Simulated Solar Flare X-Ray and Thermal Cycling Durability Evaluation of Hubble Space Telescope Thermal Control Candidate Replacement Materials

NASA Technical Reports Server (NTRS)

deGroh, Kim K.; Banks, Bruce A.; Sechkar, Edward A.; Scheiman, David A.

1998-01-01

During the Hubble Space Telescope (HST) second servicing mission (SM2), astronauts noticed that the multilayer insulation (MLI) covering the telescope was damaged. Large pieces of the outer layer of MLI (aluminized Teflon fluorinated ethylene propylene (Al-FEP)) were torn in several locations around the telescope. A piece of curled up Al-FEP was retrieved by the astronauts and was found to be severely embrittled, as witnessed by ground testing. Goddard Space Flight Center (GSFC) organized a HST MLI Failure Review Board (FRB) to determine the damage mechanism of FEP in the HST environment, and to recommend replacement insulation material to be installed on HST during the third servicing mission (SM3) in 1999. Candidate thermal control replacement materials were chosen by the FRB and tested for environmental durability under various exposures and durations. This paper describes durability testing of candidate materials which were exposed to charged particle radiation, simulated solar flare x-ray radiation and thermal cycling under load. Samples were evaluated for changes in solar absorptance and tear resistance. Descriptions of environmental exposures and durability evaluations of these materials are presented.

Degradation of Teflon(trademark) FEP Following Charged Particle Radiation and Rapid Thermal Cycling

NASA Technical Reports Server (NTRS)

Townsend, Jacqueline; Powers, Charles; Viens, Michael; Ayres-Treusdell, Mary; Munoz, Bruno

1999-01-01

During the Second Servicing Mission (SM2) of the Hubble Space Telescope (HST) severe degradation was observed on the outer layer of the thermal control blankets. Astronaut observations and photographs revealed large cracks in the metallized Teflon(trademark) FEP (fluorinated ethylene propylene), the outer layer of the multi-layer insulation (MLI), in many locations around the telescope. In an effort to understand what elements of the space environment might cause such damage, pristine Teflon(trademark) FEP was tested for durability to radiation and thermal cycling. Specimens were subjected to electron and proton fluences comparable to those experienced by HST and were subsequently thermal cycled in a custom-built rapid thermal cycle chamber. Tensile tests of the specimens showed that radiation followed by thermal cycling significantly reduced the ultimate strength and elongation of Teflon(trademark) FEP.

Degradation of Teflon(tm) FEP Following Charged Particle Radiation and Rapid Thermal Cycling

NASA Technical Reports Server (NTRS)

Townsend, Jacqueline A.; Powers, Charles E.; Viens, Michael J.; Ayres-Treusdell, Mary T.; Munoz, Bruno

1998-01-01

During the Second Servicing Mission (SM2) of the Hubble Space Telescope (HST) severe degradation was observed on the outer layer of the thermal control blankets. Astronaut observations and photographs revealed large cracks in the metallized Teflon FEP (fluorinated ethylene propylene), the outer layer of the multi-layer insulation (MLI), in many locations around the telescope. In an effort to understand what elements of the space environment might cause such damage, pristine Teflon' FEP was tested for durability to radiation and thermal cycling. Specimens were subjected to electron and proton fluences comparable to those experienced by HST and were subsequently thermal cycled in a custom-built rapid thermal cycle chamber. Tensile tests of the specimens showed that radiation followed by thermal cycling significantly reduced the ultimate strength and elongation of Teflon FEP.

Degradation of Teflon(tm) FEP Following Charged Particle Radiation and Rapid Thermal Cycling

NASA Technical Reports Server (NTRS)

Townsend, Jacqueline A.; Powers, Charles E.; Viens, Michael J.; Ayres-Treusdell, Mary T.; Munoz, Bruno F.

1998-01-01

During the Second Servicing Mission (SM2) of the Hubble Space Telescope (HST) severe degradation was observed on the outer layer of the thermal control blankets. Astronaut observations and photographs revealed large cracks in the metallized Teflon' FEP (fluorinated ethylene propylene), the outer layer of the multi-layer insulation (MLI), in many locations around the telescope. In an effort to understand what elements of the space environment might cause such damage, pristine Teflon(registered trademark) FEP was tested for durability to radiation and thermal cycling. Specimens were subjected to electron and proton fluences comparable to those experienced by HST and were subsequently thermal cycled in a custom-built rapid thermal cycle chamber. Tensile tests of the specimens showed that radiation followed by thermal cycling significantly reduced the ultimate strength and elongation of Teflon(registered trademark) FEP.

Degradation of Teflon(tm) FEP Following Charged Particle Radiation and Rapid Thermal Cycling

NASA Technical Reports Server (NTRS)

Townsend, Jacqueline; Powers, Charles; Viens, Michael; Ayres-Treusdell, Mary; Munoz, Bruno

1998-01-01

During the Second Servicing Mission (SM2) of the Hubble Space Telescope (HST) severe degradation was observed on the outer layer of the thermal control blankets. Astronaut observations and photographs revealed large cracks in the metallized Teflon(R) FEP (fluorinated ethylene propylene), the outer layer of the multi-layer insulation (MLI), in many locations around the telescope. In an effort to understand what elements of the space environment might cause such damage, pristine Teflon(R) FEP was tested for durability to radiation and thermal cycling. Specimens were subjected to electron and proton fluences comparable to those experienced by HST and were subsequently thermal cycled in a custom-built rapid thermal cycle chamber. Tensile tests of the specimens showed that radiation followed by thermal cycling significantly reduced the ultimate strength and elongation of Teflon(R) FEP.

Low Cost Fiber Optic Cable Assemblies for Local Distribution Systems

DTIC Science & Technology

1977-04-01

coefficient of friction, and is chemically inert. PFA exhibits low water permeability and ab- sorption . FEP-100 and FEP-110 were initially extruded over T08...with FEP 110. To overcome these problems, Teflon PFA 9704 was evaluated. It exhibited good extrudability which allowed application of thin and thick...superior extrudability, in addition to meeting the optical characteristics required for a cladding material, Teflon PFA was considered a viable

Effects of Various Wavelength Ranges of Vacuum Ultraviolet Radiation on Teflon FEP Film Investigated

NASA Technical Reports Server (NTRS)

Dever, Joyce A.; McCracken, Cara A.

2004-01-01

Teflon Fluorinated Ethylene Propylene (FTP) films (DuPont) have been widely used for spacecraft thermal control and have been observed to become embrittled and cracked upon exposure to the space environment. This degradation has been attributed to a synergistic combination of radiation and thermal effects. A research study was undertaken at the NASA Glenn Research Center to examine the effects of different wavelength ranges of vacuum ultraviolet (VUV) radiation on the degradation of the mechanical properties of FEP. This will contribute to an overall understanding of space radiation effects on Teflon FEP, and will provide information necessary to determine appropriate techniques for using laboratory tests to estimate space VUV degradation. Research was conducted using inhouse facilities at Glenn and was carried out, in part, through a grant with the Cleveland State University. Samples of Teflon FEP film of 50.8 microns thickness were exposed to radiation from a VUV lamp from beneath different cover windows to provide different exposure wavelength ranges: MgF2 (115 to 400 nm), crystalline quartz (140 to 400 nm), and fused silica (FS, 155 to 400 nm). Following exposure, FEP film specimens were tensile tested to determine the ultimate tensile strength and elongation at failure as a function of the exposure duration for each wavelength range. The graphs show the effect of ultraviolet exposure on the mechanical properties of the FEP samples.

Evaluation of Thermal Control Coatings and Polymeric Materials Exposed to Ground Simulated Atomic Oxygen and Vacuum Ultraviolet Radiation

NASA Technical Reports Server (NTRS)

Kamenetzky, R. R.; Vaughn, J. A.; Finckenor, M. M.; Linton, R. C.

1995-01-01

Numerous thermal control and polymeric samples with potential International Space Station applications were evaluated for atomic oxygen and vacuum ultraviolet radiation effects in the Princeton Plasma Physics Laboratory 5 eV Neutral Atomic Oxygen Facility and in the MSFC Atomic Oxygen Drift Tube System. Included in this study were samples of various anodized aluminum samples, ceramic paints, polymeric materials, and beta cloth, a Teflon-impregnated fiberglass cloth. Aluminum anodizations tested were black duranodic, chromic acid anodize, and sulfuric acid anodize. Paint samples consisted of an inorganic glassy black paint and Z-93 white paint made with the original PS7 binder and the new K2130 binder. Polymeric samples evaluated included bulk Halar, bulk PEEK, and silverized FEP Teflon. Aluminized and nonaluminized Chemfab 250 beta cloth were also exposed. Samples were evaluated for changes in mass, thickness, solar absorptance, and infrared emittance. In addition to material effects, an investigation was made comparing diffuse reflectance/solar absorptance measurements made using a Beckman DK2 spectroreflectometer and like measurements made using an AZ Technology-developed laboratory portable spectroreflectometer.

Effects of Heating on Teflon(Registered Trademark) FEP Thermal Control Material from the Hubble Space Telescope

NASA Technical Reports Server (NTRS)

deGroh, Kim; Gaier, James R.; Hall, Rachelle L.; Norris, Mary Jo; Espe, Matthew P.; Cato, Daveen R.

1999-01-01

Metallized Teflon(Registered Trademark) FEP (fluorinated ethylene propylene) thermal control material on the Hubble Space Telescope (HST) is degrading in the space environment. Teflon(Registered Trademark) FEP thermal control blankets (space-facing FEP) retrieved during the first servicing mission (SM1) were found to be embrittled on solar facing surfaces and contained microscopic cracks. During the second servicing mission (SM2) astronauts noticed that the FEP outer layer of the multi-layer insulation (MLI) covering the telescope was cracked in many locations around the telescope. Large cracks were observed on the light shield, forward shell and equipment bays. A tightly curled piece of cracked FEP from the light shield was retrieved during SM2 and was severely embrittled, as witnessed by ground testing. A Failure Review Board (FRB) was organized to determine the mechanism causing the MLI degradation. Density, x-ray crystallinity and solid state nuclear magnetic resonance (NMR) analyses of FEP retrieved during SM1 were inconsistent with results of FEP retrieved during SM2. Because the retrieved SM2 material curled while in space, it experienced a higher temperature extreme during thermal cycling, estimated at 200 C, than the SM1 material, estimated at 50 C. An investigation on the effects of heating pristine and FEP exposed on HST was therefore conducted. Samples of pristine. SM1, and SM2 FEP were heated to 200 C and evaluated for changes in density and morphology. Elevated temperature exposure was found to have a major impact on the density of the retrieved materials. Characterization of polymer morphology of as-received and heated FEP samples by NMR provided results that were consistent with the density results. These findings have provided insight to the damage mechanisms of FEP in the space environment.

Degradation of Hubble Space Telescope Metallized Teflon(trademark) FEP Thermal Control Materials

NASA Technical Reports Server (NTRS)

Hansen, Patricia A.; Townsend, Jacqueline A.; Yoshikawa, Yukio; Castro, J. David; Triolo, Jack J.; Peters, Wanda C.

1998-01-01

The mechanical and optical properties of the metallized Teflon Fluorinated Ethylene Propylene (FEP) thermal control materials on the Hubble Space Telescope (HST) have degraded over the seven years the telescope has been in orbit. Astronaut observations and photographic documentation from the Second Servicing Mission revealed severe cracks of the multi-layer insulation (MLI) blanket outer layer in many locations around the telescope, particularly on solar facing surfaces. Two samples, the outer Teflon FEP MLI layer and radiator surfaces, were characterized post- mission through exhaustive mechanical, thermal, chemical, and optical testing. The observed damage to the thermal control materials, the sample retrieval and handling, and the significant changes to the radiator surfaces of HST will be discussed. Each of these issues is addressed with respect to current and future mission requirements.

Development of Improved LOX-Compatible Laminated Gasket Composite

DTIC Science & Technology

1966-08-01

Braided Teflon 2. Bleached fluorocarbon felt 3. Teflon and asbestos fibers 4. Teflon and ceramic fibers 5. Teflon and glass fibers 6. Viton A and asbestos 7...fluorinated ethylene- propylene (Teflon FEP), polychlorotrifluoroethylene films (Aclar - Kel F), and fluorocarbon elastomers (Viton A - Fluorel, etc...2nd 10th CYCLE CYCLE CYCLE CYCLE CYCLE CYCLE CYCLE CYCLE CYCLE FILLED FLUOROCARBON GLASS FILLED TEFLON FLUOROCARBON LAMINATE ELASTOMER Figure 21

Mechanical Properties Degradation of Teflon(Trademark) FEP Returned from the Hubble Space Telescope

NASA Technical Reports Server (NTRS)

Dever, Joyce A.; deGroh, Kim K.; Townsend, Jacqueline A.; Wang, L. Len

1998-01-01

After 6.8 years on orbit, degradation has been observed in the mechanical properties of second-surface metalized Teflon(Reg) FEP (fluorinated ethylene propylene) used on the Hubble Space Telescope (HST) on the outer surface of the multi-layer insulation (MLI) blankets and on radiator surfaces. Cracking of FEP surfaces on HST was first observed upon close examination of samples with high solar exposure retrieved during the first servicing mission (SM1) conducted 3.6 years after HST was put into orbit. Astronaut observations and photographs from the second servicing mission (SM2), conducted after 6.8 years on orbit, revealed severe cracks in the FEP surfaces of the MLI on many locations around the telescope. This paper describes results of mechanical properties testing of FEP surfaces exposed for 3.6 years and 6.8 years to the space environment on HST. These tests include tensile testing, surface micro-hardness testing, and bend testing.

Synthesis of perm-selective membranes by grafting acrylic acid into air-irradiated Teflon-FEP films

NASA Astrophysics Data System (ADS)

Bozzi, Annick; Chapiro, Adolphe

Grafting acrylic acid into air-irradiated Teflon-FEP films was investigated. Pre-irradiation doses ranged from 0.5 to 10 kGy. Grafting occurred at 45 or 60°C. Homopolymerization inhibitors, ferrous ions or methylene blue, were added to the system. It was found that after completion of the reaction, within 40-100 min, membranes were obtained with very low electric resistivities. The influence of added inhibitors, pre-irradiation dose and grafting temperature was studied. From the results it is concluded that the initiating centers in air-irradiated Teflon-FEP are, on the one hand, peroxides of structure POOP', in which P is a polymeric radical and Pprime; a small fragment, and on the other trapped PO .2 radicals. The latter only react after losing their oxygen. In the presence of polymerization inhibitors, initiation involves a redox process which reduces the overall activation energy.

The use of FEP Teflon in solar cell cover technology

NASA Technical Reports Server (NTRS)

Broder, J. D.; Mazaris, G. A.

1973-01-01

FEP plastic film was used as a cover and as an adhesive to bond cover glasses to silicon solar cells. Various anti-reflective coatings were applied to cells and subsequently covered with FEP. Short circuit currents were measured before and after application of the coating and of the FEP. FEP was bonded to seven of the nine differently coated cells, with no change in the total short circuit current in four cases.

The use of FEP Teflon in solar cell cover technology

NASA Technical Reports Server (NTRS)

Broder, J. D.; Mazaris, G. A.

1974-01-01

FEP plastic film was used as a cover and as an adhesive to bond cover glasses to silicon solar cells. Various anti-reflective coatings were applied to cells and subsequently covered with FEP. Short-circuit currents were measured before and after application of the coating and of the FEP. FEP bonded to seven of the nine differently coated cells, with no change in the total short circuit current in four cases.

Covalent immobilisation of antibodies in Teflon-FEP microfluidic devices for the sensitive quantification of clinically relevant protein biomarkers.

PubMed

Pivetal, Jeremy; Pereira, Filipa M; Barbosa, Ana I; Castanheira, Ana P; Reis, Nuno M; Edwards, Alexander D

2017-03-13

This study reports for the first time the sensitive colorimetric and fluorescence detection of clinically relevant protein biomarkers by sandwich immunoassays using the covalent immobilisation of antibodies onto the fluoropolymer surface inside Teflon®-FEP microfluidic devices. Teflon®-FEP has outstanding optical transparency ideal for high-sensitivity colorimetric and fluorescence bioassays, however this thermoplastic is regarded as chemically inert and very hydrophobic. Covalent immobilisation can offer benefits over passive adsorption to plastic surfaces by allowing better control over antibody density, orientation and analyte binding capacity, and so we tested a range of different and novel covalent immobilisation strategies. We first functionalised the inner surface of a 10-bore, 200 μm internal diameter FEP microcapillary film with high-molecular weight polyvinyl alcohol (PVOH) without changing the outstanding optical transparency of the device delivered by the matched refractive index of FEP and water. Glutaraldehyde immobilisation was compared with the use of photoactivated linkers and NHS-ester crosslinkers for covalently immobilising capture antibodies onto PVOH. Three clinically relevant sandwich ELISAs were tested against the cytokine IL-1β, the myocardial infarct marker cardiac troponin I (cTnI), and the chronic heart failure marker brain natriuretic peptide (BNP). Overall, glutaraldehyde immobilisation was effective for BNP assays, but yielded unacceptable background for IL-1β and cTnI assays caused by direct binding of the biotinylated detection antibody to the modified PVOH surface. We found NHS-ester groups reacted with APTES-treated PVOH coated fluoropolymers. This facilitated a novel method for capture antibody immobilisation onto fluoropolymer devices using a bifunctional NHS-maleimide crosslinker. The density of covalently immobilised capture antibodies achieved using PVOH/APTES/NHS/maleimide approached levels seen with passive adsorption, and sensitive and quantitative assay performance was achieved using this method. Overall, the PVOH coating provided an excellent surface for controlled covalent antibody immobilisation onto Teflon®-FEP for performing high-sensitivity immunoassays.

Analysis of Retrieved Hubble Space Telescope Thermal Control Materials

NASA Technical Reports Server (NTRS)

Townsend, Jacqueline A.; Hansen, Patricia A.; Dever, Joyce A.; Triolo, Jack J.

1998-01-01

The mechanical and optical properties of the thermal control materials on the Hubble Space Telescope (HST) have degraded over the nearly seven years the telescope has been in orbit. Astronaut observations and photographs from the Second Servicing Mission (SM2) revealed large cracks in the metallized Teflon FEP, the outer-layer of the multi-layer insulation (MLI), in many locations around the telescope. Also, the emissivity of the bonded metallized Teflon FEP radiator surfaces of the telescope has increased over time. Samples of the top layer of the MLI and radiator material were retrieved during SM2, and a thorough investigation into the de-radiation followed in order to determine the primary cause of the damage. Mapping of the cracks on HST and the ground testing showed that thermal cycling with deep-layer damage from electron and proton radiation are necessary to cause the observed embrittlement. Further, strong, evidence was found indicating that chain scission (reduced molecular weight) is the dominant form of damage to the metallized Teflon FEP.

Space environmental effects on silvered Teflon thermal control surfaces

NASA Technical Reports Server (NTRS)

Hemminger, C. S.; Stuckey, W. K.; Uht, J. C.

1991-01-01

Cumulative space environment effects on Ag/fluorinated ethylene propylene (FEP) were a function of exposure orientation. Samples from nineteen silvered Teflon (Ag/FEP) thermal control surfaces recovered from the Long Duration Exposure Facility (LDEF) were analyzed to determine changes in this material as a function of position on the spacecraft. Although solar absorptance and infrared emittance of measured thermal blanket specimens are relatively unchanged from control specimen values, significant changes in surface morphology, composition and chemistry were observed. Researchers hypothesize that the FEP surfaces on LDEF were degraded by ultraviolet radiation exposure at all orientations, but that the damaged material had been removed by erosion from the blankets exposed to atomic oxygen flux and that contamination is masking the damage on trays flanking the trailing edge.

Use of a single-bowl continuous-flow centrifuge for dewatering suspended sediments: effect on sediment physical and chemical characteristics

USGS Publications Warehouse

Rees, T.F.; Leenheer, J.A.; Ranville, J.F.

1991-01-01

Sediment-recovery efficiency of 86-91% is comparable to that of other types of CFC units. The recovery efficiency is limited by the particle-size distribution of the feed water and by the limiting particle diameter that is retained in the centrifuge bowl. Contamination by trace metals and organics is minimized by coating all surfaces that come in contact with the sample with either FEP or PFA Teflon and using a removable FEP Teflon liner in the centrifuge bowl. -from Authors

Performance of silvered Teflon (trademark) thermal control blankets on spacecraft

NASA Technical Reports Server (NTRS)

Pippin, Gary; Stuckey, Wayne; Hemminger, Carol

1993-01-01

Silverized Teflon (Ag/FEP) is a widely used passive thermal control material for space applications. The material has a very low alpha/e ratio (less than 0.1) for low operating temperatures and is fabricated with various FEP thicknesses (as the Teflon thickness increases, the emittance increases). It is low outgassing and, because of its flexibility, can be applied around complex, curved shapes. Ag/FEP has achieved multiyear lifetimes under a variety of exposure conditions. This has been demonstrated by the Long Duration Exposure Facility (LDEF), Solar Max, Spacecraft Charging at High Altitudes (SCATHA), and other flight experiments. Ag/FEP material has been held in place on spacecraft by a variety of methods: mechanical clamping, direct adhesive bonding of tapes and sheets, and by Velcro(TM) tape adhesively bonded to back surfaces. On LDEF, for example, 5-mil blankets held by Velcro(TM) and clamping were used for thermal control over 3- by 4-ft areas on each of 17 trays. Adhesively bonded 2- and 5-mil sheets were used on other LDEF experiments, both for thermal control and as tape to hold other thermal control blankets in place. Performance data over extended time periods are available from a number of flights. The observed effects on optical properties, mechanical properties, and surface chemistry will be summarized in this paper. This leads to a discussion of performance life estimates and other design lessons for Ag/FEP thermal control material.

Space environmental effects on silvered Teflon thermal control surfaces

NASA Technical Reports Server (NTRS)

Hemminger, C. S.; Stuckey, W. K.; Uht, J. C.

1992-01-01

Cumulative space environmental effects on silver/fluorinated ethylene propylene (Ag/FEP) were a function of exposure orientation. Samples from nineteen silvered Teflon (Ag/FEP) thermal control surfaces recovered from the Long Duration Exposure Facility (LDEF) were analyzed to determine changes in this material as a function of position on the spacecraft. Although solar absorptance and infrared emittance of measured thermal blanket specimens are relatively unchanged from control specimen values, significant changes in surface morphology, composition, and chemistry were observed. We hypothesize that the FEP surfaces on the LDEF are degraded by UV radiation at all orientations, but that the damaged material has been removed by erosion from the blankets exposed to atomic oxygen flux and that contamination is masking the damage in some areas on the trays flanking the trailing edge.

Performance of silvered Teflon thermal control blankets on spacecraft

NASA Astrophysics Data System (ADS)

Pippin, G.; Stuckey, W. K.; Hemminger, C. S.

1993-03-01

Silver-backed fluorinated ethylene propylene Teflon (Ag/FEP) thin film material was used for thermal control in many locations on the Long Duration Exposure Facility (LDEF). The Ag/FEP registered the effects of atomic oxygen, solar ultraviolet radiation, meteoroid and debris impacts, thermal cycling, and contamination. This report summarizes the post-flight condition of the Ag/FEP, compares the results with performance on other spacecraft, and presents lifetime estimates for use under a variety of environmental exposures. Measurements of optical property and mechanical property and surface chemistry changes with exposure conditions, and their significance for design considerations and expected performance lifetimes, are reported for material flown on LDEF. The LDEF based data provides detailed information performance of Ag/FEP under relatively long term exposure in low Earth orbit. Comparison of this data with results from short term shuttle flights, Solar Max, SCATHA, other satellites, and ground based measurements is made to present a comprehensive summary of the use of this material for spacecraft applications.

Investigation of space stable thermal control coating properties

NASA Technical Reports Server (NTRS)

Mookherji, T.

1971-01-01

A capability to study the nuclear magnetic resonance of spacecraft thermal control coating has been built utilizing an electromagnet and V-series and Wl-series electronics. The electronics associated with the electromagnet had to be modified to make it compatible with the resonance measuring system. Resonance measurements have been performed on ZnO, Zn2TiO4 and FEP Teflon. The failure to observe resonance in ZnO and Zn2TiO4 has been theoretically explained. The linewidth and second moment measurements on ultraviolet irradiated FEP Teflon showed that there was no measurable degradation of the material due to short term irradiation.

PALS and SPM/EFM investigation of charged nanoporous electret films

NASA Astrophysics Data System (ADS)

Chiang, Dar-Ming; Liu, Wen-Liang; Chen, Jen-Luan; Susuki, Ryoichi

2005-08-01

The electret properties of nanoporous Teflon-FEP films, fabricated by the super-critical fluids method and charged by the corona method at room temperature, are investigated. PALS and SAXS are applied first to examine the charge characteristics of a free volume of electret materials. The topography and surface charges of electret materials are determined by scanning probe microscopy and electric field microscopy, respectively. The experimental results reveal that the interior surface areas of the pores of the electret materials influence the retention and stability of charge. Initial and aged surface charge was increased by factors of two and ten, with and without nanoporous Teflon-FEP films, respectively.

An analysis of LDEF-exposed silvered FEP teflon thermal blanket material

NASA Technical Reports Server (NTRS)

Young, Philip R.; Slemp, Wayne S.

1991-01-01

The characterization of selected silvered fluorinated ethylene propylene (FEP) teflon thermal blanket material which received 5 years and 9 months of exposure to the LEO environment on the Long Duration Exposure Facility is reported. X-ray photoelectron spectroscopy, infrared, and thermal analyses did not detect a significant change at the molecular level as the result of this exposure. However, various microscopic analyses revealed a roughening of the coating surface due to atomic oxygen erosion which resulted in some materials changing from specular reflectors of visible radiation to diffuse reflectors. The potential effect of silicon-containing molecular contamination on these materials is addressed.

Flexible, FEP-Teflon covered solar cell module development

NASA Technical Reports Server (NTRS)

Rauschenbach, H. S.; Cannady, M. D.

1976-01-01

Techniques and equipment were developed for the large scale, low-cost fabrication of lightweight, roll-up and fold-up, FEP-Teflon encapsulated solar cell modules. Modules were fabricated by interconnecting solderless single-crystal silicon solar cells and heat laminating them at approximately 300 C between layers of optically clear FEP and to a loadbearing Kapton substrate sheet. Modules were fabricated from both conventional and wraparound contact solar cells. A heat seal technique was developed for mechanically interconnecting modules into an array. The electrical interconnections for both roll-up and fold-up arrays were also developed. The use of parallel-gap resistance welding, ultrasonic bonding, and thermocompression bonding processes for attaching interconnects to solar cells were investigated. Parallel-gap welding was found to be best suited for interconnecting the solderless solar cells into modules. Details of the fabrication equipment, fabrication processes, module and interconnect designs, environmental test equipment, and test results are presented.

Measured current drainage through holes in various dielectrics up to 2 kilovolts in a dilute plasma

NASA Technical Reports Server (NTRS)

Grier, N. T.; Mckinzie, D. J., Jr.

1972-01-01

The electron current drained from a plasma through approximately 0.05 cm diameter holes in eight possible space applicable dielectrics placed on a probe biased at voltages up to 2000 V dc have been determined both theoretically and experimentally. The dielectrics tested were Parylene C and N, Teflon FEP type C, Teflon TFE, Nomex, quartz 7940 Corning Glass, Mylar A, and Kapton H polymide film. A Laplace field was used to predict an upper limit for the drainage current. The measured current was less than the computed current for quartz, Teflon FEP, and the 0.0123 cm thick sample of Parylene N for all voltages tested. The drainage current through the other dielectrics became equal to or greater than the computed current at a voltage below 2000 V. The magnitudes of the currents were between 0.1 and 10 microamperes for most of the dielectrics.

HST Multi Layer Insulation Failure Review Board Findings

NASA Technical Reports Server (NTRS)

Townsend, Jacqueline; Hansen, Patricia

1998-01-01

The mechanical and optical properties of the thermal control materials on the Hubble Space Telescope (HST) have degraded over the nearly seven years the telescope has been in orbit. Astronaut observations and photographs from the Second Servicing Mission (SM2) revealed large cracks in the metallized Teflon fluorinated ethylene propylene (FEP), the outer layer of the multi-layer insulation (MLI), in many locations around the telescope. Also, the absorptance of the bonded metallized Teflon FEP radiator surfaces of the telescope has increased over time. A Failure Review Board was established to determine the damage mechanism and to identify a replacement material. Samples of the top layer of the MLI and radiator material were retrieved during SM2, and a thorough investigation into the degradation followed in order to determine the primary cause of the damage. Mapping of the cracks on HST and the ground testing showed that thermal cycling with deep-layer damage from electron and proton radiation are necessary to cause the observed embrittlement. Further, strong evidence was found indicating that chain scission (reduced molecular weight) is the dominant form of damage to the metallized Teflon FEP. Given the damage to the outer layer of the multi-layer insulation (MLI) that was apparent during the second servicing mission (SM2), the decision was made to replace the outer layer during subsequent servicing missions. The replacement material had to meet the stringent thermal requirements of the spacecraft and maintain structural integrity for at least ten years. Ten candidate materials were exposed to simulated orbital environments and a replacement material was selected. This presentation will summarize the FRB results, in particular, the analysis of the retrieved specimens, the results of the simulated environmental exposures, and the selection of the replacement material. The NASA Space Environments and Effects community needs to hear these results because they reveal that Teflon (FEP) films should not be used in LEO as routinely as they are today.

A fixed tilt solar collector employing reversible vee-trough reflectors and vacuum tube receivers for solar heating and cooling systems

NASA Technical Reports Server (NTRS)

Selcuk, M. K.

1977-01-01

The usefulness of vee-trough concentrators in improving the efficiency and reducing the cost of collectors assembled from evacuated tube receivers was studied in the vee-trough/vacuum tube collector (VTVTC) project. The VTVTC was analyzed rigorously and various mathematical models were developed to calculate the optical performance of the vee-trough concentrator and the thermal performance of the evacuated tube receiver. A test bed was constructed to verify the mathematical analyses and compare reflectors made out of glass, Alzak and aluminized FEP Teflon. Tests were run at temperatures ranging from 95 to 180 C. Vee-trough collector efficiencies of 35 to 40% were observed at an operating temperature of about 175 C. Test results compared well with the calculated values. Predicted daily useful heat collection and efficiency values are presented for a year's duration of operation temperatures ranging from 65 to 230 C. Estimated collector costs and resulting thermal energy costs are presented. Analytical and experimental results are discussed along with a complete economic evaluation.

Vacuum Ultraviolet (VUV) radiation-induced degradation of Fluorinated Ethylene Propylene (FEP) Teflon aboard the Long Duration Exposure Facility (LDEF)

NASA Technical Reports Server (NTRS)

Brinza, David E.; Stiegman, A. E.; Staszak, Paul R.; Laue, Eric G.; Liang, Ranty H.

1992-01-01

Examination of fluorinated ethylene propylene (FEP) copolymer specimens recovered from the Long Duration Exposure Facility (LDEF) provides evidence for degradation attributed to extended solar vacuum ultraviolet (VUV) irradiation. Scanning electron microscope (SEM) images of sheared FEP film edges reveal the presence of a highly embrittled layer on the exposed surface of specimens obtained from the trailing edge of the LDEF. Similar images obtained for leading edge and control FEP films do not exhibit evidence for such an embrittled layer. Laboratory VUV irradiation of FEP films is found to produce a damage layer similar to that witnessed in the LDEF trailing edge films. Spectroscopic analyses of irradiated films provide data to advance a photochemical mechanism for degradation.

Diagnostic Techniques for Semiconductor Materials Processing. Materials Research Society Symposium Proceedings Held in Boston, Massachusetts on November 29-December 2, 1993. Volume 324

DTIC Science & Technology

1994-05-01

phototransmittance (PT) to study PM-HEMTs with different electron densities and found that the first derivative of the ab- sorption coefficient with...circle before striking the sample. Samples are normally sealed into bags of FEP Teflon I and suspended in the beam between strings of PFA Teflon. Prompt

Analysis of Ag/FEP Thermal Control Blanket Performance From Multiple Satellites

NASA Technical Reports Server (NTRS)

Pippin, Gary; Normand, E.; Woll, S.; Munafo, Paul (Technical Monitor)

2001-01-01

Materials performance data from operational spacecraft and spacecraft experiments has slowly accumulated over the years. Much of this data is obtained indirectly by analyzing temperature measurements telemetered to ground. Due to the Space Transportation System (STS) program, materials performance data has also been obtained by flying materials on satellites, or on the Space Shuttle itself, for limited periods of time, and then returning the materials to ground for post-flight examination. During the course of NASA contract NAS8-98213, the authors have extended the analysis of data reported for selected materials flown on a variety of spacecraft over the past 30 years. In this paper we discuss changes in two properties of silver- or aluminum-backed (metallized) FEP Teflon due to exposure to specific environmental factors on-orbit. First, the change in solar absorptance (alpha(sub s)) of metallized FEP Teflon as a function of particulate radiation will be discussed. Data providing the change in solar absorptance of metallized FEP as a function of days on orbit has been published for NTS-2 satellite, several NavStar Global Positioning Satellites (GPS), the SCATHA experiment, and the ML-101 satellite. The unique approach that we have taken is to calculate the absorbed radiation dose within the Ag/FEP for the various satellite orbits, and to plot the change in solar absorptance, alpha(sub s), as a function of the dose; the behavior agrees with the same data from laboratory tests. Second, the variation of the atomic oxygen induced material recession rate of metallized FEP will be discussed. Data from certain Space Shuttle flights, a Lockheed experiment [approximately 105 days in low Earth orbit (LEO)], and the Long Duration Exposure Facility allows the variation of the material recession rate of Ag/FEP to be estimated under conditions that include atomic oxygen exposure.

Hubble Space Telescope Bi-Stem Thermal Shield Analyses

NASA Technical Reports Server (NTRS)

Finlay, Katherine A.

2004-01-01

The Hubble Space Telescope (HST) was launched April 24, 1990, and was deployed April 25 into low Earth orbit (LEO). It was soon discovered that the metal poles holding the solar arrays were expanding and contracting as the telescope orbited the Earth passing between the sunlight and the Earth s shadow. The expansion and contraction, although very small, was enough to cause the telescope to shake because of thermal-induced jitters, a detrimental effect when trying to take pictures millions of miles away. Therefore, the European Space Agency (ESA, the provider of the solar arrays) built new solar arrays (SA-11) that contained bi-stem thermal shields which insulated the solar array metal poles. These thermal shields were made of 2 mil thick aluminized-Teflon fluorinated ethylene propylene (FEP) rings fused together into a circular bellows shape. The new solar arrays were put on the HST during an extravehicular activity (EVA), also called an astronaut space walk, during the first servicing mission (SM1) in December 1993. An on-orbit photograph of the HST with the SA-11, and a close up of the bellows-like structure of the thermal shields is provided in Figure 1.

Analysis of Silverized Teflon Thermal Control Material Flown on the Long Duration Exposure Facility

NASA Technical Reports Server (NTRS)

Pippin, H. Gary

1995-01-01

Silver backed teflon (Ag/FEP) material used for thermal control on the Long Duration Exposure Facility (LDEF) has been examined in detail. Optical, mechanical, and chemical properties were characterized for specimens exposed to a variety of space environmental conditions. Recession rates were determined for this material. Samples were obtained from virtually every LDEF location except the Earth-end. Atomic oxygen exposed regions changed from specular to diffusely reflective.

Vacuum ultraviolet radiation/atomic oxygen synergism in fluorinated ethylene propylene Teflon erosion

NASA Technical Reports Server (NTRS)

Stiegman, A. E.; Brinza, David E.; Laue, Eric G.; Anderson, Mark S.; Liang, Ranty H.

1992-01-01

A micrographic investigation is reported of samples of the fluorinated ethylene propylene (FEP) Teflon thermal-blanketing materials recovered from the Long-Duration Exposure Facility (LDEF) satellite. The samples are taken from the trailing edge and row 8 which correspond to exposures to vacuum UV (VUV) and VUV + atomic O, respectively. Data are taken from SEM and IR-spectra observations, and the LDEF leading-edge FEP shows a high degree of erosion, roughening, and sharp peaks angled in the direction of the flow of atomic O. The trailing edge sample influenced primarily by VUV shows a hard brittle layer and some cracked mosaic patterns. Comparisons to a reference sample suggest that the brittle layer is related to exposure to VUV and is removed by atomic-O impingement. Polymers that are stable to VUV radiation appear to be more stable in terms of atomic oxygen.

Teflon Examination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dooraghi, A. A.; Seetho, I.; Smith, J.. A.

2017-04-27

In this document, we outline an experiment performed at LLNL to evaluate the radiation sensitivity of polytetrafluoroethylene (PTFE) and a PTFE isomer, fluorinated ethylene propylene (FEP). We demonstrate that PTFE, a material currently used for assessing MicroCT system stability, shows higher radiation-dependent change in x-ray attenuation than FEP. Specifically, for a dose of approximately 1.44 x 10 3 Gy, the linear attenuation coefficient (LAC) of PTFE changes by 0.8 ± 0.1 %. During the same irradiation period, the LAC for FEP changes by 0.02 ± 0.1 %, which is within the statistical uncertainty of the measurement. Due to its highermore » resistance to radiation damage, we recommend that LLNL and partner labs operating under the Department of Homeland Security’s Explosives Division (DHS EXD) transition to the use of FEP as a reference material in place of PTFE.« less

Erosion Results of the MISSE 8 Polymers Experiment After 2 Years of Space Exposure on the International Space Station

NASA Technical Reports Server (NTRS)

de Groh, Kim K.; Banks, Bruce A.; Asmar, Olivia C.; Yi, Grace T.; Mitchell, Gianna G.; Guo, Aobo; Sechkar, Edward A.

2017-01-01

Polymers and other oxidizable materials on the exterior of spacecraft in the low Earth orbit (LEO) space environment can be eroded due to reaction with atomic oxygen (AO). Therefore, in order to design durable spacecraft, it is important to know the LEO AO erosion yield (E(sub y), volume loss per incident oxygen atom) of materials susceptible to AO reaction. A spaceflight experiment, called the Polymers Experiment, which contained 42 samples, was developed to determine the effect of solar exposure on the AO E(sub y) of fluoropolymers flown in ram, wake, or zenith orientations. The Polymers Experiment was exposed to the LEO space environment on the exterior of the International Space Station (ISS) as part of the Materials International Space Station Experiment 8 (MISSE 8) mission. The MISSE 8 mission included samples flown in a zenith/nadir orientation for 2.14 years in the MISSE 8 Passive Experiment Container (PEC), and samples flown in a ram/wake orientation for 2.0 years in the Optical Reflector Materials Experiment-III (ORMatEIII) tray. The experiment included Kapton H (Registered Trademark) witness samples for AO fluence determination in each orientation. This paper provides an overview of the MISSE 8 mission, a description of the flight experiment with details on the polymers flown, the characterization techniques used, the AO fluence for each exposure orientation, and the LEO E(sub y) results. The E(sub y) of Teflon fluorinated ethylene propylene (FEP) samples flown in ram, wake, and zenith orientations have been compared, and the E(sub y) was found to be highly dependent on orientation and therefore environmental exposure. The FEP E(sub y) was found to directly correlate with the solar exposure/AO fluence ratio showing the effect of solar radiation and/or heating due to solar exposure on FEP erosion. In addition, back-surface carbon painted FEP (C-FEP) flown in the zenith orientation had a significantly higher E(sub y) than clear FEP or Al-FEP further indicating that heating has a significant impact on the erosion of FEP. This experiment provides valuable LEO flight data on the erosion of Teflon FEP, a commonly used spacecraft thermal insulation.

Charging and discharging Teflon

NASA Technical Reports Server (NTRS)

Passenheim, B. C.; Vanlint, V. A. J.

1981-01-01

The charging and discharging characteristics of several common satellite materials exposed to 0-30KV electrons are measured. Teflon is discussed because the charging characteristics are radically altered immediately after a spontaneous discharge. The exterior geometry of the test structure is shown. In all cases dielectric samples were 82 cm in diameter mounted on the front of a 120 cm diameter cylinder supported on an 85 cm, 0.95 cm thick plexiglass disc. Dielectric materials investigated were: back surface aluminized Kapton, back surface silvered Teflon, silicon alkyd white thermal control paint, and 50 cm by 50 cm array of 0.030 cm thick MgF2 coated fused silica solar cell cover slips.

Optical and electrical properties of ion beam textured Kapton and Teflon

NASA Technical Reports Server (NTRS)

Mirtich, M. J.; Sovey, J. S.

1977-01-01

An electron bombardment argon ion source was used to ion etch polyimide (Kapton) and fluorinated ethylene, FEP (Teflon). Samples of polyimide and FEP were exposed to (0.5-1.0) keV Ar ions at ion current densities of (1.0-1/8) mA/sq cm for various exposure times. Changes in the optical and electrical properties of the samples were used to characterize the exposure. Spectral reflectance and transmittance measurements were made between 0.33 and 2.16 micron m using an integrating sphere after each exposure. From these measurements, values of solar absorptance were obtained. Total emittance measurements were also recorded for some samples. Surface resistivity was used to determine changes in the electrical conductivity of the etched samples. A scanning electron microscope recorded surface structure after exposure. Spectral optical data, resistivity measurements, calculated absorptance and emittance measurements are presented along with photomicrographs of the surface structure for the various exposures to Ar ions.

Silver-Teflon contamination UV radiation study

NASA Technical Reports Server (NTRS)

Muscari, J. A.

1978-01-01

Silver-Teflon (Ag/FEP) is planned to be used as the thermal control material covering the radiator surfaces on the shuttle orbiter payload bay doors. These radiators require the use of materials that have a very low solar absorptance and a high emittance for heat rejection. However, operationally, materials used on these critical radiator surfaces, such as silver-Teflon, will be exposed to a variety of conditions which include both the natural as well as the induced environments from the Shuttle Orbiter. A complete test facility was assembled, and detailed test procedures and a test matrix were developed. Measurements of low solar absorptance were taken before and after contamination, at intervals during irradiation, and after sample cleaning to fulfill all the requirements.

ESCA study of several fluorocarbon polymers exposed to atomic oxygen in low earth orbit or within or downstream from a radio-frequency oxygen plasma

NASA Technical Reports Server (NTRS)

Golub, Morton A.; Wydeven, Theodore; Cormia, Robert D.

1989-01-01

The ESCA (electron spectroscopy for chemical analysis) spectra of films of Tedlar, tetrafluoroethylene-hexafluoropropylene copolymer (in the form of a Teflon FEP coating on Kapton H, i.e., Kapton F), and polytetrafluoroethylene (Teflon or Teflon TFE), exposed to atomic oxygen O(3P) either in LEO on the STS-8 Space Shuttle or within or downstream from a radio-frequency oxygen plasma, were compared. The major difference in surface chemistry of Tedlar induced by the various exposures to O(3P) was a much larger uptake of oxygen when etched either in or out of the glow of an O2 plasma than when etched in LEO. In contrast, Kapton F exhibited very little surface oxidation during any of the three different exposures to O(3P), while Teflon was scarcely oxidized.

Laser Processing for Interconnect Technology

DTIC Science & Technology

1992-02-27

2.1 0.0002 - available in film ethylene- - insoluble propylene (FEP) Perfluoroalkoxy ( PFA ) Teflon AF Amorphous DuPont 1.9 0.0002 - soluble form...t,) where the pulse is sorption coefficient, hv is the photon energy, and f is the a maximum at the surface at time t0. The distance marker fraction

Evaluation of Brushing as a Lunar Dust Mitigation Strategy for Thermal Control Surfaces

NASA Technical Reports Server (NTRS)

Gaier, James R.; Journey, Khrissaundra; Christopher, Steven; Davis, Shanon

2011-01-01

Evaluation of brushing to remove lunar simulant dust from thermal control surfaces is described. First, strip brushes made with nylon, PTFE, or Thunderon (Nihon Sanmo Dyeing Company Ltd.) bristles were used to remove JSC-1AF dust from AZ93 thermal control paint or aluminized FEP (AlFEP) thermal control surface under ambient laboratory conditions. Nylon and PTFE bristles removed a promising amount of dust from AZ93, and nylon and Thunderon bristles from AlFEP. But when these were tested under simulated lunar conditions in the lunar dust adhesion bell jar (LDAB), they were not effective. In a third effort, seven brushes made up of three different materials, two different geometries, and different bristle lengths and thicknesses were tested under laboratory conditions against AZ93 and AlFEP. Two of these brushes, the Zephyr fiberglass fingerprint brush and the Escoda nylon fan brush, removed over 90 percent of the dust, and so were tested in the fourth effort in the LDAB. They also performed well under these conditions recovering 80 percent or more of the original thermal performance (solar absorptance/thermal emittance) of both AZ93 and AgFEP after 20 strokes, and 90 or more percent after 200 strokes

Evaluation of Brushing as a Lunar Dust Mitigation Strategy for Thermal Control Surfaces

NASA Technical Reports Server (NTRS)

Gaier, James R.; Journey, Hhrissaundra; Christopher, Steven; Davis, Shanon

2011-01-01

Evaluation of brushing to remove lunar simulant dust from thermal control surfaces is described. First, strip brushes made with nylon, PTFE, or Thunderon bristles were used to remove JSC-1AF dust from AZ93 thermal control paint or aluminized FEP (AlFEP) thermal control surface under ambient laboratory conditions. Nylon and PTFE bristles removed a promising amount of dust from AZ93, and nylon and Thunderon bristles from AlFEP. But when these were tested under simulated lunar conditions in the lunar dust adhesion bell jar (LDAB), they were not effective. In a third effort, seven brushes made up of three different materials, two different geometries, and different bristle lengths and thicknesses were tested under laboratory conditions against AZ93 and AlFEP. Two of these brushes, the Zephyr fiberglass fingerprint brush and the Escoda nylon fan brush, removed over 90 percent of the dust, and so were tested in the fourth effort in the LDAB. They also performed well under these conditions recovering 80 percent or more of the original thermal performance (solar absorptance/thermal emittance) of both AZ93 and AgFEP after 20 strokes, and 90 or more percent after 200 strokes.

Solar Effects on Tensile and Optical Properties of Hubble Space Telescope Silver-Teflon(Registered Trademark) Insulation

NASA Technical Reports Server (NTRS)

deGroh, Kim, K.; Dever, Joyce A.; Snyder, Aaron; Kaminski, Sharon; McCarthy, Catherine E.; Rapoport, Alison L.; Rucker, Rochelle N.

2006-01-01

A section of the retrieved Hubble Space Telescope (HST) solar array drive arm (SADA) multilayer insulation (MLI), which experienced 8.25 years of space exposure, was analyzed for environmental durability of the top layer of silver-Teflon (DuPont) fluorinated ethylene propylene (Ag-FEP). Because the SADA MLI had solar and anti-solar facing surfaces and was exposed to the space environment for a long duration, it provided a unique opportunity to study solar effects on the environmental degradation of Ag-FEP, a commonly used spacecraft thermal control material. Data obtained included tensile properties, solar absorptance, surface morphology and chemistry. The solar facing surface was found to be extremely embrittled and contained numerous through-thickness cracks. Tensile testing indicated that the solar facing surface lost 60% of its mechanical strength and 90% of its elasticity while the anti-solar facing surface had ductility similar to pristine FEP. The solar absorptance of both the solar facing surface (0.155 plus or minus 0.032) and the anti-solar facing surface (0.208 plus or minus 0.012) were found to be greater than pristine Ag-FEP (0.074). Solar facing and anti-solar facing surfaces were microscopically textured, and locations of isolated contamination were present on the anti-solar surface resulting in increased localized texturing. Yet, the overall texture was significantly more pronounced on the solar facing surface indicating a synergistic effect of combined solar exposure and increased heating with atomic oxygen erosion. The results indicate a very strong dependence of degradation, particularly embrittlement, upon solar exposure with orbital thermal cycling having a significant effect.

Follow-up on the effects of the space environment on UHCRE thermal blankets

NASA Technical Reports Server (NTRS)

Levadou, Francois; Vaneesbeek, Marc

1993-01-01

An overview of the effects of the space environment on the thermal blanket of the UHCRE experiment is presented with an emphasis on atomic oxygen (AO) erosion. A more accurate value for FEP Teflon reaction efficiency is given and corresponds, at normal incidence, to 3.24 10(exp -25) cu cm/atomic, therefore, the FEP Teflon erosion corresponding to the Long Duration Exposure Facility (LDEF) total mission is 29.5 microns. A power 1.44 of the cosine of the incident angle of the oxygen atoms is found. It is shown that this value is not far from the power found using Fergusson's relationship between efficiency and energy of the O-atoms. An hypothesis concerning the effect of oxygen ions (O(+)) is also presented. The presence of oxygen ions may explain the different results obtained from different flights and from laboratory tests. Finally an XPS analysis of Chemglaze Z306(tm) black paint demonstrates the presence of silicone in the paint which may explain part of the contamination found on LDEF.

Evaluation of Low Earth Orbit Environmental Effects on International Space Station Thermal Control Materials

NASA Technical Reports Server (NTRS)

Dever, Joyce A.; Rutledge, Sharon K.; Hasegawa, Mark M.; Reed, Charles K.

1998-01-01

Samples of International Space Station (ISS) thermal control coatings were exposed to simulated low Earth orbit (LEO) environmental conditions to determine effects on optical properties. In one test, samples of the white paint coating Z-93P were coated with outgassed products from Tefzel(R) (ethylene tetrafluoroethylene copolymer) power cable insulation as-may occur on ISS. These samples were then exposed, along with an uncontaminated Z-93P witness sample, to vacuum ultraviolet (VUV) radiation to determine solar absorptance degradation. The Z-93P samples coated with Tefzel(R) outgassing products experienced greater increases in solar absorptance than witness samples not coated with Tefzel(R) outgassing products. In another test, samples of second surface silvered Teflon(R) FEP (fluorinated ethylene propylene), SiO. (where x=2)-coated silvered Teflon(R) FEP, and Z-93P witness samples were exposed to the combined environments of atomic oxygen and VLTV radiation to determine optical properties changes due to these simulated ISS environmental effects. This test verified the durability of these materials in the absence of contaminants.

Atomic Oxygen (ATOX) simulation of Teflon FEP and Kapton H surfaces using a high intensity, low energy, mass selected, ion beam facility

NASA Technical Reports Server (NTRS)

Vered, R.; Grossman, E.; Lempert, G. D.; Lifshitz, Y.

1994-01-01

A high intensity (greater than 10(exp 15) ions/sq cm) low energy (down to 5 eV) mass selected ion beam (MSIB) facility was used to study the effects of ATOX on two polymers commonly used for space applications (Kapton H and Teflon FEP). The polymers were exposed to O(+) and Ne(+) fluences on 10(exp 15) - 10(exp 19) ions/sq cm, using 30eV ions. A variety of analytical methods were used to analyze the eroded surfaces including: (1) atomic force microscopy (AFM) for morphology measurements; (2) total mass loss measurements using a microbalance; (3) surface chemical composition using x-ray photoelectron spectroscopy (XPS), and (4) residual gas analysis (RGA) of the released gases during bombardment. The relative significance of the collisional and chemical degradation processes was evaluated by comparing the effects of Ne(+) and O(+) bombardment. For 30 eV ions it was found that the Kapton is eroded via chemical mechanisms while Teflon FEP is eroded via collisional mechanisms. AFM analysis was found very powerful in revealing the evolution of the damage from its initial atomic scale (roughness of approx. 1 nm) to its final microscopic scale (roughness greater than 1 micron). Both the surface morphology and the average roughness of the bombarded surfaces (averaged over 1 micron x 1 micron images by the system's computer) were determined for each sample. For 30 eV a non linear increase of the Kapton roughness with the O(+) fluence was discovered (a slow increase rate for fluences phi less than 5 x 10(exp 17) O(+)/sq cm, and a rapid increase rate for phi greater than 5 x 10(exp 17) O(+)/sq cm). Comparative studies on the same materials exposed to RF and DC oxygen plasmas indicate that the specific details of the erosion depend on the simulation facility emphasizing the advantages of the ion beam facility.

Study of Improvement of Hydrogen Maser Frequency Standard

NASA Technical Reports Server (NTRS)

Crampton, S. B.

1977-01-01

The research work dealt primarily with reducing the atom leakage rate using as storage surfaces the FEP Teflon surfaces conventionally used in contemporary hydrogen maser frequency standards. Some work was also done on a possible alternative to the conventional surfaces, but the results here and elsewhere suggest that the alternative surface is not promising enough to warrant much further work.

Waste Minimization in Circuit Board Manufacturing by PARMOD(TM) Technology

DTIC Science & Technology

1998-06-24

a foil package in air or in a plastic syringe. Thermogravimetric Analysis (TGA) Ink samples were evaluated using thermogravimetric analysis in...DTA Differential Thermal Analysis FEP Fluorinated Ethylene Propylene (Teflon®) FTIR Fourier Transform Infrared spectroscopy MOD Metallo-Organic...Decomposition ROM Reactive Organic Medium SEM Scanning Electron Microscopy TGA Thermal Gravimetry Analysis Torr Unit of pressure (one mm mercury

Degradation of FEP thermal control materials returned from the Hubble Space Telescope

NASA Technical Reports Server (NTRS)

Zuby, Thomas M.; Degroh, Kim K.; Smith, Daniela C.

1995-01-01

After an initial 3.6 years of space flight, the Hubble Space Telescope was serviced through a joint effort with the NASA and the European Space Agency. Multi-layer insulation (MLI) was retrieved from the electronics boxes of the two magnetic sensing systems (MSS), also called the magnetometers, and from the returned solar array (SA-I) drive arm assembly. The top layer of each MLI assembly is fluorinated ethylene propylene (FEP, a type of Teflon). Dramatic changes in material properties were observed when comparing areas of high solar fluence to areas of low solar fluence. Cross sectional analysis shows atomic oxygen (AO) erosion values up to 25.4 mu m (1 mil). Greater occurrences of through-thickness cracking and surface microcracking were observed in areas of high solar exposure. Atomic force microscopy (AFM) showed increases in surface microhardness measurements with increasing solar exposure. Decreases in FEP tensile strength and elongation were measured when compared to non-flight material. Erosion yield and tensile results are compared with FEP data from the Long Duration Exposure Facility. AO erosion yield data, solar fluence values, contamination, micrometeoroid or debris impact sites, and optical properties are presented.

Charging rates of metal-dielectric structures. [with implications for spacecraft

NASA Technical Reports Server (NTRS)

Purvis, C. K.; Staskus, J. V.; Roche, J. C.; Berkopec, F. D.

1979-01-01

Metal plates partially covered by 0.01-centimeter-thick fluorinated ethylene-propylene (FEP) Teflon were charged in the Lewis Research Center's geomagnetic substorm simulation facility using 5-, 8-, 10-, and 12-kilovolt electron beams. Surface voltage as a function of time was measured for various initial conditions (Teflon discharged or precharged) with the metal plate grounded or floating. Results indicate that both the charging rates and the levels to which the samples become charged are influenced by the geometry and initial charge state of the insulating surfaces. The experiments are described and the results are presented and discussed. NASA charging analyzer program (NASCAP) models of the experiments have been generated, and the predictions obtained are described. Implications of the study results for spacecraft are discussed.

Design and development of pressure and repressurization purge system for reusable space shuttle multilayer insulation system

NASA Technical Reports Server (NTRS)

1972-01-01

The experimental determination of purge bag materials properties, development of purge bag manufacturing techniques, experimental evaluation of a subscale purge bag under simulated operating conditions and the experimental evaluation of the purge pin concept for MLI purging are discussed. The basic purge bag material, epoxy fiberglass bounded by skins of FEP Teflon, showed no significant permeability to helium flow under normal operating conditions. Purge bag small scale manufacturing tests were conducted to develop tooling and fabrication techniques for use in full scale bag manufacture. A purge bag material layup technique was developed whereby the two plys of epoxy fiberglass enclosed between skins of FEP Teflon are vacuum bag cured in an oven in a single operation. The material is cured on a tool with the shape of a purge bag half. Plastic tooling was selected for use in bag fabrication. A model purge bag 0.6 m in diameter was fabricated and subjected to a series of structural and environmental tests simulating various flight type environments. Pressure cycling tests at high (450 K) and low (200 K) temperature as well as acoustic loading tests were performed. The purge bag concept proved to be structurally sound and was used for the full scale bag detailed design model.

Evaluation of advanced bladder technology

NASA Technical Reports Server (NTRS)

Christensen, M. V.; Pasternak, R. A.

1972-01-01

Research conducted during this period is reported. Studies presented include: (1) diffusion and permeation of CO2, O2, N2, and NO2 through polytetra fluoroethylene; (2) diffusion, permeation and solubility of simple gases (CO2, O2, N2, CH4, C2H6, C3H8, and C2H4) through a copolymer of hexafluoro propylene and tetrafluoro ethylene (FEP); (3) viscous flow and diffusion of gases throug small apertures; (4) diffusion and permeation of O2, N2, CO2, CH4, C2H6, and C3H8 through nitroso rubber; and (5) results of gas transport studies with carborane siloxane, nitroso rubber, silicone membrane, krytox coating on teflon, and FEP coated glass cloth. Publications generated under this program are listed.

Spacecraft Charging Standard Report.

DTIC Science & Technology

1980-09-30

SSPM include: SAMPLE POTENTIAL (with respect to S/C ground) Aluminized Kapton -2.0 kV Silvered Teflon -4.0 kV Astroquartz -3.7 kV 50.3 Analysis. As...and potential gradients on the space vehicle (candidate spacecraft locations for ESD tests) (The NASCAP computer code, when validated, will be useful...The coupling analysis should then determine as a minimum: I. electromagnetic fields generated interior to the space vehicle due to ESD 2. induced

The Solar Shield: A Thermally Insulating, Broad-Band, Electromagnetic Window for Satellites

DTIC Science & Technology

1986-06-02

1.2 but is difficult to machine to thicknesses less than about 1/4 in. without breakage. The one disadvantage of the quartz paper is that it is somewhat...flimsy. Additional structural S•.support was provided by fusing one side of the paper to FEP teflon-coated Kapton* in a laminat - ing press. Kapton...loose quartz fibers from escaping. .4.’ A non-outgassing, polyester netting+ was chosen to separate the composite layers from eachother. * DuPont Corp

Vacuum ultraviolet radiation/atomic oxygen synergism in materials reactivity

NASA Technical Reports Server (NTRS)

Koontz, Steven; Leger, Lubert; Albyn, Keith; Cross, Jon

1990-01-01

Experimental results are presented which indicate that low fluxes of vacuum UV (VUV) radiation exert a pronounced influence on the atomic oxygen reactivity of such fluorocarbon and fluorocarbon spacecraft materials as the FEP Teflon and PCTFE that are under consideration for the Space Station Freedom. With simultaneous exposure to VUV fluxes comparable to those experienced in LEO, the reactivity of these materials becomes comparable to that of Kapton; VUV radiation has also been shown to increase the reactivity of Kapton with thermal-energy oxygen atoms.

Investigation into the effect of plasma pretreatment on the adhesion of parylene to various substrates

NASA Technical Reports Server (NTRS)

Riley, T.; Mahuson, T. C.; Seibert, K.

1979-01-01

A procedure is described for using argon and oxygen plasmas to promote adhesion of parylene coatings upon many difficult-to-bond substrates. Substrates investigated were gold, nickel, kovar, teflon (FEP), kapton, silicon, tantalum, titanium, and tungsten. Without plasma treatment, 180 deg peel tests yield a few g/cm (oz/in) strengths. With dc plasma treatment in the deposition chamber, followed by coating, peel strengths are increased by one to two orders of magnitude.

Protection of Polymers from the Space Environment by Atomic Layer Deposition

NASA Astrophysics Data System (ADS)

Lindholm, Ned F.; Zhang, Jianming; Minton, Timothy K.; O'Patchen, Jennifer; George, Steven M.; Groner, Markus D.

2009-01-01

Polymers in space may be subjected to a barrage of incident atoms, photons, and/or ions. For example, oxygen atoms can etch and oxidize these materials. Photons may act either alone or in combination with oxygen atoms to degrade polymers and paints and thus limit their usefulness. Colors fade under the intense vacuum ultraviolet (VUV) solar radiation. Ions can lead to the build-up of static charge on polymers. Atomic layer deposition (ALD) techniques can provide coatings that could mitigate many challenges for polymers in space. ALD is a gas-phase technique based on two sequential, self-limiting surface reactions, and it can deposit very uniform, conformal, and pinhole-free films with atomic layer control. We have studied the efficacy of various ALD coatings to protect Kapton® polyimide, FEP Teflon®, and poly(methyl methacrylate) films from atomic-oxygen and VUV attack. Atomic-oxygen and VUV studies were conducted with the use of a laser-breakdown source for hyperthermal O atoms and a D2 lamp as a source of VUV light. These studies used a quartz crystal microbalance (QCM) to monitor mass loss in situ, as well as surface profilometry and scanning electron microscopy to study the surface recession and morphology changes ex situ. Al2O3 ALD coatings applied to polyimide and FEP Teflon® films protected the underlying substrates from O-atom attack, and ZnO coatings protected the poly(methyl methacrylate) substrate from VUV-induced damage.

Mass analysis of neutral particles and ions released during electrical breakdowns on spacecraft surfaces

NASA Technical Reports Server (NTRS)

Kendall, B. R. F.

1983-01-01

A specialized spectrometer was designed and developed to measure the mass and velocity distributions of neutral particles (molecules and molecular clusters) released from metal-backed Teflon and Kapton films. Promising results were obtained with an insulation breakdown initiation system based on a moveable contact touching the insulated surfaces. A variable energy, high voltage pulse is applied to the contact. The resulting surface damage sites can be made similar in size and shape to those produced by a high voltage electron beam system operating at similar discharge energies. The point discharge apparatus was used for final development of several high speed recording systems and for measurements of the composition of the materials given off by the discharge. Results with this apparatus show evolution of large amounts of fluorocarbon fragments from discharge through Teflon FEP, while discharges through Kapton produce mainly very light hydrocarbon fragments at masses below about 80 a.m.u.

Effects of the LDEF environment on the Ag/FEP thermal blankets

NASA Technical Reports Server (NTRS)

Levadou, Francois; Pippin, H. Gary

1992-01-01

This presentation was made by Francois Levadou at the NASA Langley Research Center LDEF materials workshop, November 19-22, 1991. It represents the results to date on the examination of silvered teflon thermal blankets primarily from the Ultra-heavy Cosmic Ray Experiment and also from the blanket from the Park Seed Company experiment. ESA/ESTEC and Boeing conducted a number of independent measurements on the blankets and in particular on the exposed fluorinated ethylene-propylene (FEP) layer of the blankets. Mass loss, thickness, and thickness profile measurements have been used by ESA, Boeing, and NASA LeRC to determine recession and average erosion yield under atomic oxygen exposure. Tensile strength and percent elongation to failure data, surface characterization by ESCA, and SEM images are presented. The Jet Propulsion Laboratory analysis of vacuum radiation effects is also presented. The results obtained by the laboratories mentioned and additional results from the Aerospace Corporation on samples provided by Boeing are quite similar and give confidence in the validity of the data.

A Study to Analyze the Permeation of High Density Gases and Propellant Vapors Through Single Layer Teflon or Teflon Structure Materials and Laminations. Volume 1

NASA Technical Reports Server (NTRS)

Johnson, R. L.; Young, Donald L. (Technical Monitor)

1967-01-01

This report contains the results of a fifteen month analytical and experimental study of the leakage rate of the pressurant gases (N2, He) and the propellant vapors (N2O4,N2H4) through bladder structures consisting of two layers of Teflon separated by a metallic foil diffusion barrier containing microscopic or larger holes. Results were obtained for the steady state leakage rate through circular holes and long rectangular openings in the barrier for arbitrary thicknesses of the two Teflon layers. The effect of hole shape and relative hole position on the leakage rate were studied. The transient problem was analyzed and it was shown that steady state calculations are adequate for estimating the leakage rate. A computer program entitled "Diffusion Analyzer Program" was developed to calculate the leakage rate, both transient and steady state. Finally, the analytical results were compared to experimentally determined values of the leakage rate through a model laminated bladder structure. The results of the analysis are in good agreement with experiment. The experimental effort (Part II of the Bladder Permeation Program) measured the solubility, diffusion coefficient and permeability of helium, nitrogen and nitrogen tetroxide vapor through Teflon TFE and FEP membranes. Data were obtained in the temperature range of 25 to 100 C at pressures ranging from near vacuum to about 20 atmospheres. Results of the experimental effort were compared with the limited data previously reported. As a verification to the applicability of results to actual bladder systems, counter diffusion tests were performed with a laminated sample containing aluminum foil with a selected group of holes.

LDEF materials data analysis: Representative examples

NASA Technical Reports Server (NTRS)

Pippin, H. Gary; Crutcher, E. R.

1992-01-01

Results of measurements on silverized teflon, heat shrink tubing and nylon tie downs on the wire harness clamps, silvered hex nuts, and contamination deposits are presented. We interpret the results in terms of our microenvironments exposure model and locations on the Long Duration Exposure Facility (LDEF). Distinct changes in the surface properties of FEP were observed as a function of UV exposure. Significant differences in outgassing characteristics were detected for hardware on the interior row 3 relative to identical hardware on the interior row 3 relative to identical hardware on nearby rows. The implications for in service performance are reviewed.

Thermal control materials on EOIM-3

NASA Technical Reports Server (NTRS)

Finckenor, Miria M.; Linton, Roger C.; Kamenetzky, Rachel R.; Vaughn, Jason A.

1995-01-01

Thermal control paints, anodized aluminum, and beta cloth samples were flown on STS-46 as part of the Evaluation of Oxygen Interaction with Materials Experiment (EOIM-3). The thermal control paints flown on EOIM-3 include ceramic and polyurethane-based paints. Passively exposed samples are compared to actively heated samples and controlled exposure samples. Optical property measurements of absorptivity, emissivity, and spectrofluorescence are presented for each paint. Several variations of anodized aluminum, including chromic acid anodize, sulfuric acid anodize, and boric/sulfuric acid anodize were flown on the actively heated trays and the passive exposure trays. The post-flight optical properties are within tolerances for these materials. Also flown were two samples of yellow anodized aluminum. The yellow anodized aluminum samples darkened noticeably. Samples of aluminized and unaluminized beta cloth, a fiberglass woven mat impregnated with TFE Teflon, were flown with passive exposure to the space environment. Data from this part of the experiment is correlated to observations from LDEF and erosion of the Teflon thin film samples also flown on EOIM-3 and LDEF.

Hubble Space Telescope Thermal Blanket Repair Design and Implementation

NASA Technical Reports Server (NTRS)

Ousley, Wes; Skladany, Joseph; Dell, Lawrence

2000-01-01

Substantial damage to the outer layer of Hubble Space Telescope (HST) thermal blankets was observed during the February 1997 servicing mission. After six years in LEO, many areas of the aluminized Teflon(R) outer blanket layer had significant cracks, and some material was peeled away to expose inner layers to solar flux. After the mission, the failure mechanism was determined, and repair materials and priorities were selected for follow-on missions. This paper focuses on the thermal, mechanical, and EVA design requirements for the blanket repair, the creative solutions developed for these unique problems, hardware development, and testing.

Scanning Tunneling Microscopy analysis of space-exposed polymer films

NASA Technical Reports Server (NTRS)

Kalil, Carol R.; Young, Philip R.

1993-01-01

The characterization of the surface of selected space-exposed polymer films by Scanning Tunneling Microscopy (STM) is reported. Principles of STM, an emerging new technique for materials analysis, are reviewed. The analysis of several films which received up to 5.8 years of low Earth orbital (LEO) exposure onboard the NASA Long Duration Exposure Facility (LDEF) is discussed. Specimens included FEP Teflon thermal blanket material, Kapton film, and several experimental polymer films. Ultraviolet and atomic oxygen-induced crazing and erosion are described. The intent of this paper is to demonstrate how STM is enhancing the understanding of LEO space environmental effects on polymer films.

Thermal design of the IMP-I and H spacecraft

NASA Technical Reports Server (NTRS)

Hoffman, R. H.

1974-01-01

A description of the thermal subsystem of the IMP-I and H spacecraft is presented. These two spacecraft were of a larger and more advanced type in the Explorer series and were successfully launched in March 1971 and September 1972. The thermal requirements, analysis, and design of each spacecraft are described including several specific designs for individual experiments. Techniques for obtaining varying degrees of thermal isolation and contact are presented. The thermal control coatings including the spaceflight performance of silver-coated FEP Teflon are discussed. Predicted performance is compared to measured flight data. The good agreement between them verifies the validity of the thermal model and the selection of coatings.

Secondary electron emission from electrically charged fluorinated-ethylene-propylene Teflon for normal and non-normal electron incidence. M.S. Thesis; [spacecraft thermal coatings

NASA Technical Reports Server (NTRS)

Budd, P. A.

1981-01-01

The secondary electron emission coefficient was measured for a charged polymer (FEP-Teflon) with normally and obliquely incident primary electrons. Theories of secondary emission are reviewed and the experimental data is compared to these theories. Results were obtained for angles of incidence up to 60 deg in normal electric fields of 1500 V/mm. Additional measurements in the range from 50 to 70 deg were made in regions where the normal and tangential fields were approximately equal. The initial input angles and measured output point of the electron beam could be analyzed with computer simulations in order to determine the field within the chamber. When the field is known, the trajectories can be calculated for impacting electrons having various energies and angles of incidence. There was close agreement between the experimental results and the commonly assumed theoretical model in the presence of normal electric fields for angles of incidence up to 60 deg. High angle results obtained in the presence of tangential electric fields did not agree with the theoretical models.

Space Environmental Effects on the Optical Properties of Selected Transparent Polymers

NASA Technical Reports Server (NTRS)

Edwards, David L.; Willowby, Douglas J.; Hubbs, Whitney C.; Piszczor, Michael F., Jr.; Bowden, Mary L.

1997-01-01

Transparent polymer films are currently considered for use as solar concentrating lenses for spacecraft power and propulsion systems. These polymer films concentrate solar energy onto energy conversion devices such as solar cells and thermal energy systems. Conversion efficiency is directly related to the polymer transmission. Space environmental effects will decrease the transmission and thus reduce the conversion efficiency. This investigation focuses on the effects of ultraviolet and charged particle radiation on the transmission of selected transparent polymers. Multiple candidate polymer samples were exposed to near ultraviolet (NUV) radiation to screen the materials and select optimum materials for further study. All materials experienced transmission degradation of varying degree. A method was developed to normalize the transmission loss and thus rank the materials according to their tolerance of NUV. Teflon(Tm) FEP and Teflon(Tm) PFA were selected for further study. These materials were subjected to a combined charged particle dose equivalent to 5 years in a typical geosynchronous Earth orbit (GEO). Results from these NUV screening tests and the 5 year GEO equivalent dose are presented.

Impact penetration experiments in teflon targets of variable thickness

NASA Astrophysics Data System (ADS)

Hoerz, F.; Cintala, M. J.; Bernhard, R. P.; See, T. H.

1993-03-01

Approximately 20.4 sq m of Teflon thermal blankets on the nonspinning Long Duration Exposure Facility (LDEF) were exposed to the orbital debris and micrometeoroid environment in low-Earth orbit (LEO) for approximately 5.7 years. Each blanket consisted of an outer layer (approximately 125 micron thick) of FEP Teflon that was backed by a vapor-deposited metal mirror (Inconel; less than 1 micron thick). The inner surface consisted of organic binders and Chemglaze thermal protective paint (approximately 50 micron thick) resulting in a somewhat variable, total blanket thickness of approximately 180 to 200 microns. There was at least one of these blankets, each exposing approximately 1.2 sq m of surface area, on nine of LDEF's 12 principal pointing directions, the exceptions being Rows 3, 9, and 12. As a consequence, these blankets represent a significant opportunity for micrometeoroid and debris studies, in general, and specifically they provide an opportunity to address those issues that require information about pointing direction (i.e., spatial density of impact events as a function of instrument orientation). During deintegration of the LDEF spacecraft at KSC, all penetration holes greater than or equal to 300 micron in diameter were documented and were recently synthesized in terms of spatial density as a function of LDEF viewing direction by. The present report describes ongoing cratering and penetration experiments in pure Teflon targets, which are intended to establish the relationships between crater or penetration-hole diameters and the associated projectile dimensions at laboratory velocities (i.e., 6 km/s). The ultimate objective of these efforts is to extract reliable mass-frequencies and associated fluxes of hypervelocity particles in LEO.

Effects of Gas-Wall Partitioning in Teflon Tubing, Instrumentation and Other Materials on Time-Resolved Measurements of Gas-Phase Organic Compounds

NASA Astrophysics Data System (ADS)

Pagonis, D.; Deming, B.; Krechmer, J. E.; De Gouw, J. A.; Jimenez, J. L.; Ziemann, P. J.

2017-12-01

Recently it has been shown that gas-phase organic compounds partition to and from the walls of Teflon environmental chambers. This process is fast, reversible, and can be modeled as absorptive partitioning. Here these studies were extended to investigate gas-wall partitioning inside Teflon tubing by introducing step function changes in the concentration of compounds being sampled and measuring the delay in the response of a proton transfer reaction-mass spectrometer (PTR-MS). We find that these delays are significant for compounds with a saturation vapor concentration (c*) below 106 μg m-3, and that the Teflon tubing and the PTR-MS both contribute to the delays. Tubing delays range from minutes to hours under common sampling conditions and can be accurately predicted by a simple chromatography model across a range of tubing lengths and diameters, flow rates, compound functional groups, and c*. This method also allows one to determine the volatility-dependent response function of an instrument, which can be convolved with the output of the tubing model to correct for delays in instrument response time for these "sticky" compounds. This correction is expected to be of particular interest to researchers utilizing and developing chemical ionization mass spectrometry (CIMS) techniques, since many of the multifunctional organic compounds detected by CIMS show significant tubing and instrument delays. These results also enable better design of sampling systems, in particular when fast instrument response is needed, such as for rapid transients, aircraft, or eddy covariance measurements. Additional results presented here extend this method to quantify the relative sorptive capacities for other commonly used tubing materials, including PFA, FEP, PTFE, PEEK, glass, copper, stainless steel, and passivated steel.

Ground-based simulation of LEO environment: Investigations of a select LDEF material: FEP Teflon (trademark)

NASA Technical Reports Server (NTRS)

Cross, Jon B.; Koontz, Steven L.

1993-01-01

The Long Duration Exposure Facility (LDEF) has produced a wealth of data on materials degradation in the low earth orbit (LEO) space environment and has conclusively shown that surface chemistry (as opposed to surface physics-sputtering) is the key to understanding and predicting the degradation of materials in the LEO environment. It is also clear that materials degradation and spacecraft contamination are closely linked and that the fundamental mechanisms responsible for this linking are in general not well understood especially in the area of synergistic effects. The study of the fundamental mechanisms underlying materials degradation in LEO is hampered by the fact that the degradation process itself is not observed during the actual exposure to the environment. Rather the aftermath of the degradation process is studied, i.e., the material that remains after exposure is observed and mechanisms are proposed to explain the observed results. The EOIM-3 flight experiment is an attempt to bring sophisticated diagnostic equipment into the space environment and monitor the degradation process in real time through the use of mass spectrometry. More experiments of this nature which would include surface sensitive diagnostics (Auger and photoelectron spectroscopes) are needed to truly unravel the basic chemical mechanisms involved in the materials degradation process. Since these in-space capabilities will most likely not be available in the near future, ground-based LEO simulation facilities employing sophisticated diagnostics are needed to further advance the basic understanding of the materials degradation mechanisms. The LEO simulation facility developed at Los Alamos National Laboratory has been used to investigate the atomic oxygen/vacuum ultraviolet (AO/VUV) enhanced degradation of FEP Teflon. The results show that photo-ejection of polymer fragments occur at elevated temperature (200 C), that VUV synergistic rare gas sputtering of polymer fragments occur even at 25 C, and that combined OA/VUV interaction produces a wide variety of gas phase reaction products.

Area scaling investigations of charging phenomena. [discharge pulse characteristics of Teflon thermal control tape

NASA Technical Reports Server (NTRS)

Aron, P. R.; Staskus, J. V.

1979-01-01

The charging and discharging behavior of square, planar samples of silvered, fluorinated ethylene-propylene (FEP) Teflon thermal control tape was measured. The equilibrium voltage profiles scaled with the width of the sample. A wide range of discharge pulse characteristics was observed, and the area dependences of the peak current, charge, and pulse widths are described. The observed scaling of the peak currents with area was weaker than that previously reported. The discharge parameters were observed to depend strongly on the grounding impedance and the beam voltage. Preliminary results suggest that measuring only the return-current-pulse characteristics is not adequate to describe the spacecraft discharging behavior of this material. The seams between strips of tape appear to play a fundamental role in determining the discharging behavior. An approximate propagation velocity for the charge cleanoff was extracted from the data. The samples - 232, 1265, and 5058 square centimeters in area - were exposed at ambient temperature to a 1- to 2-nA/sq cm electron beam at energies of 10, 15, and 20 kilovolts in a 19-meter-long by 4.6-meter-diameter simulation facility at the Lewis Research Center.

Photoconductivity of high-voltage space insulating materials

NASA Technical Reports Server (NTRS)

Coffey, H. T.; Nanevicz, J. E.; Adamo, R. C.

1975-01-01

The dark and photoconductivities of four high voltage spacecraft insulators, Kapton-H, FEP Teflon, Parylene, and fused quartz, were studied under a variety of conditions intended to simulate a space environment. All measurements were made in a vacuum of less than .00001 torr while the temperature was varied from 22 C to 100 C. Some of the samples used employed conventional deposited metal electrodes--others employed electrodes composed either of an electron beam or a plasma formed by ionization of the residual gas in the test chamber. Test results show: (1) Kapton had unusual conduction properties; it conductivity decreased by more than an order of magnitude when heated at 100 C in a vacuum, but ultimately attained a stable and reproducible value. (2) Both Teflon and fused quartz had high dark resistivities but low photoresistivities when exposed to UV. Optical-density measurements revealed that both materials transmitted UV with little attenuation. (3) Parylene was found to have a low but relatively stable resistivity--comparatively minor changes occurred upon heating or illuminating the sample. Optical-density measurements showed that Parylene was absorbent in the UV and would prevent photoemission from the metal electrode on the back surface.

Cratering and penetration experiments in Teflon targets at velocities from 1 to 7 km/s

NASA Technical Reports Server (NTRS)

Hoerz, Friedrich; Bernhard, Ronald P.; Cintala, Mark J.; See, Thomas H.

1995-01-01

Approximately 20 sq m of protective thermal blankets, largely composed of Teflon, were retrieved from the Long Duration Exposure Facility (LDEF) after the spacecraft had spent approximately 5.7 years in space. Examination of these blankets revealed that they contained thousands of hypervelocity impact features ranging from micron-sized craters to penetration holes several millimeters in diameter. We conducted impact experiments in an effort to reproduce such features and to -- hopefully -- understand the relationships between projectile size and the resulting crater or penetration-hole diameter over a wide range of impact velocity. Such relationships are needed to derive the size- and mass-frequency distribution and flux of natural and man-made particles in low-Earth orbit. Powder propellant and light-gas guns were used to launch soda-lime glass spheres of 3.175 mm (1/8 inch) nominal diameter (Dp) into pure Teflon FEP targets at velocities ranging from 1 to 7 km/s. Target thickness (T) was varied over more than three orders of magnitude from infinite halfspace targets (Dp/T less than 0.1) to very thin films (Dp/T greater than 100). Cratering and penetration of massive Teflon targets is dominated by brittle failure and the development of extensive spall zones at the target's front and, if penetrated, the target's rear side. Mass removal by spallation at the back side of Teflon targets may be so severe that the absolute penetration-hole diameter (Dh) can become larger than that of a standard crater (Dc) at relative target thicknesses of Dp/T = 0.6-0.9. The crater diameter is infinite halfspace Teflon targets increases -- at otherwise constant impact conditions -- with encounter velocity by a factor of V0.44. In contrast, the penetration-hole size is very thin foils (Dp/T greater than 50) is essentially unaffected by impact velocity. Penetrations at target thicknesses intermediate to these extremes will scale with variable exponents of V. Our experimental matrix is sufficiently systematic and complete, up to 7 km/s, to make reasonable recommendations for the velocity-scaling of Teflon craters and penetrations. We specifically suggest that cratering behavior and associated equations dominate all impacts in which the shock-pulse duration of the projectile (tp) is shorter than that of the target (tt). We also demonstrate that each penetration hole from space-retrieved surfaces may be assigned a unique projectile size, provided an impact velocity is known or assumed. This calibration seems superior to the traditional ballistic-limit approach.

Cratering and penetration experiments in Teflon targets at velocities from 1 to 7 km/s

NASA Astrophysics Data System (ADS)

Hoerz, Friedrich; Bernhard, Ronald P.; Cintala, Mark J.; See, Thomas H.

1995-02-01

Approximately 20 sq m of protective thermal blankets, largely composed of Teflon, were retrieved from the Long Duration Exposure Facility (LDEF) after the spacecraft had spent approximately 5.7 years in space. Examination of these blankets revealed that they contained thousands of hypervelocity impact features ranging from micron-sized craters to penetration holes several millimeters in diameter. We conducted impact experiments in an effort to reproduce such features and to -- hopefully -- understand the relationships between projectile size and the resulting crater or penetration-hole diameter over a wide range of impact velocity. Such relationships are needed to derive the size- and mass-frequency distribution and flux of natural and man-made particles in low-Earth orbit. Powder propellant and light-gas guns were used to launch soda-lime glass spheres of 3.175 mm (1/8 inch) nominal diameter (Dp) into pure Teflon FEP targets at velocities ranging from 1 to 7 km/s. Target thickness (T) was varied over more than three orders of magnitude from infinite halfspace targets (Dp/T less than 0.1) to very thin films (Dp/T greater than 100). Cratering and penetration of massive Teflon targets is dominated by brittle failure and the development of extensive spall zones at the target's front and, if penetrated, the target's rear side. Mass removal by spallation at the back side of Teflon targets may be so severe that the absolute penetration-hole diameter (Dh) can become larger than that of a standard crater (Dc) at relative target thicknesses of Dp/T = 0.6-0.9. The crater diameter is infinite halfspace Teflon targets increases -- at otherwise constant impact conditions -- with encounter velocity by a factor of V0.44. In contrast, the penetration-hole size is very thin foils (Dp/T greater than 50) is essentially unaffected by impact velocity. Penetrations at target thicknesses intermediate to these extremes will scale with variable exponents of V. Our experimental matrix is sufficiently systematic and complete, up to 7 km/s, to make reasonable recommendations for the velocity-scaling of Teflon craters and penetrations. We specifically suggest that cratering behavior and associated equations dominate all impacts in which the shock-pulse duration of the projectile (tp) is shorter than that of the target (tt). We also demonstrate that each penetration hole from space-retrieved surfaces may be assigned a unique projectile size, provided an impact velocity is known or assumed. This calibration seems superior to the traditional ballistic-limit approach.

Comparison of Observed Beta Cloth Interactions with Simulated and Actual Space Environment

NASA Technical Reports Server (NTRS)

Kamenetzy, R. R.; Finckenor, M. M.

1999-01-01

A common component of multilayer insulation blankets is beta cloth, a woven fiberglass cloth impregnated with Teflon(TM). It is planned for extensive use on the International Space Station. The Environmental Etl'ects Group of the Marshall Space Flight Center Materials, Processing, and Manufacturing Department has investigated the impact of atomic oxygen (AO) and ultraviolet (UV) radiation on the optical properties of plain and aluminized beta cloth. both in the laboratory and as part of long-duration flight experiments. These investigations indicate that beta cloth is susceptible to darkening in the presence of UV radiation, dependent on the additives used. AO interactions resulted in bleaching of the beta cloth.

Sensitive Technique Developed Using Atomic Force Microscopy to Measure the Low-Earth-Orbit Atomic Oxygen Erosion of Polymers

NASA Technical Reports Server (NTRS)

deGroh, Kim D.; Banks, Bruce A.; Clark, Gregory W.; Hammerstrom, Anne; Youngstrom, Erica; Kaminski, Carolyn; Fine, Elizabeth; Marx, Laura

2001-01-01

A recession measurement technique has been developed at the NASA Glenn Research Center to determine the atomic oxygen durability of polymers exposed to the space environment for short durations. Polymers such as polyimide Kapton and Teflon FEP (fluorinated ethylene propylene, DuPont) are commonly used in spacecraft because of their desirable properties, such as flexibility, low density, and in the case of FEP, low solar absorptance and high thermal emittance. Polymers on the exterior of spacecraft in the low- Earth-orbit environment are exposed to energetic atomic oxygen, resulting in erosion and potential structural loss. It is, therefore, important to understand the atomic oxygen erosion yield (E, the volume loss per incident oxygen atom) of polymers being considered in spacecraft design. Because long-term space exposure data are rare and very costly, short-term exposures, such as on the space shuttles, are often relied on for atomic oxygen erosion determination. The most common technique for determining E is through mass-loss measurements. For limited-duration exposure experiments, such as shuttle flight experiments, the atomic oxygen fluence is often so small that mass-loss measurements are not sensitive enough. Therefore, a recession measurement technique has been developed at Glenn to obtain accurate erosion yields of polymers exposed to low atomic oxygen fluences.

The Syntheses and Structure of the First Vanadium(IV) and Vanadium(V) Binary Azides, V(N3)4, [V(N3)6]2- and [V(N3)6]- (Preprint)

DTIC Science & Technology

2009-11-17

V(N3)3(N3S2)] 2- , [22] have been reported, and no binary vanadium(V) compounds had been known except for VF5, VF6 - and V2O5 . By analogy with...valves. Volatile materials were handled in a Pyrex glass or stainless steel/Teflon-FEP vacuum line. [31] All reaction vessels were passivated with ClF3...successful synthesis of the [V(N3)6] - anion, the only binary vanadium(V) compound known besides VF5, VF6 - and V2O5 . N1’ N8 N9 N1 N2 N3 V N4 N5 N6 N2

Materials characterization study of conductive flexible second surface mirrors

NASA Technical Reports Server (NTRS)

Levadou, F.; Bosma, S. J.; Paillous, A.

1981-01-01

The status of prequalification and qualification work on conductive flexible second surface mirrors is described. The basic material is FEP Teflon witn either aluminium or silver vacuum deposited reflectors. The top layer has been made conductive by deposition of layer of a indium oxide. The results of a prequalification program comprised of decontamination, humidity, thermal cycling, thermal shock and vibration tests are presented. Thermo-optical and electrical properties. The results of a prequalification program comprised of decontamination, humidity, thermal cycling, thermal shock and vibration tests are presented. Thermo-optical and electrical properties, the electrostatic behavior of the materials under simulated substorm environment and electrical conductivity at low temperatures are characterized. The effects of simulated ultra violet and particles irradiation on electrical and thermo-optical properties of the materials are also presented.

The NASA atomic oxygen effects test program

NASA Technical Reports Server (NTRS)

Banks, Bruce A.; Rutledge, Sharon K.; Brady, Joyce A.

1988-01-01

The NASA Atomic Oxygen Effects Test Program was established to compare the low earth orbital simulation characteristics of existing atomic oxygen test facilities and utilize the collective data from a multitude of simulation facilities to promote understanding of mechanisms and erosion yield dependence upon energy, flux, metastables, charge, and environmental species. Four materials chosen for this evaluation include Kapton HN polyimide, FEP Teflon, polyethylene, and graphite single crystals. The conditions and results of atomic oxygen exposure of these materials is reported by the participating organizations and then assembled to identify degrees of dependency of erosion yields that may not be observable from any single atomic oxygen low earth orbital simulation facility. To date, the program includes 30 test facilities. Characteristics of the participating test facilities and results to date are reported.

High Altitude Venus Operational Concept (HAVOC): Proofs of Concept

NASA Technical Reports Server (NTRS)

Jones, Christopher A.; Arney, Dale C.; Bassett, George Z.; Clark, James R.; Hennig, Anthony I.; Snyder, Jessica C.

2015-01-01

The atmosphere of Venus is an exciting destination for both further scientific study and future human exploration. A recent internal NASA study of a High Altitude Venus Operational Concept (HAVOC) led to the development of an evolutionary program for the exploration of Venus, with focus on the mission architecture and vehicle concept for a 30-day crewed mission into Venus's atmosphere at 50 kilometers. Key technical challenges for the mission include performing the aerocapture maneuvers at Venus and Earth, inserting and inflating the airship at Venus during the entry sequence, and protecting the solar panels and structure from the sulfuric acid in the atmosphere. Two proofs of concept were identified that would aid in addressing some of the key technical challenges. To mitigate the threat posed by the sulfuric acid ambient in the atmosphere of Venus, a material was needed that could protect the systems while being lightweight and not inhibiting the performance of the solar panels. The first proof of concept identified candidate materials and evaluated them, finding FEP-Teflon (Fluorinated Ethylene Propylene-Teflon) to maintain 90 percent transmittance to relevant spectra even after 30 days of immersion in concentrated sulfuric acid. The second proof of concept developed and verified a packaging algorithm for the airship envelope to inform the entry, descent, and inflation analysis.

ECTFE (HALAR) as a New Material for Primary Sample Containment of Astromaterials

NASA Technical Reports Server (NTRS)

Calaway, Michael J.; McConnell, J.T.

2014-01-01

Fluoropolymers, such as Teflon® (PTFE, PFA, FEP) and Viton® (FKM), have been used for over 40 years in curating astromaterials at NASA JSC. In general, fluoropolymers have low outgassing and particle shedding properties that reduce cross-contamination to curated samples. Ethylene - Chlorotrifluoroethylene (ECTFE), commonly called Halar® (trademark of Solvay Solexis), is a partially fluorinated semi-crystalline copolymer in the same class of fluoropolymers with superior abrasion resistance and extremely low permeability to liquids, gases, and vapors than any other fluoropolymer (fig. 1). ECTFE coatings are becoming more popular in the nuclear, semiconductor, and biomedical industry for lining isolation containment gloveboxes and critical piping as well as other clean room applications. A study was conducted at NASA JSC to evaluate the potential use of Halar on future sample return missions as a material for primary sample containment.

Surface contamination on LDEF exposed materials

NASA Technical Reports Server (NTRS)

Hemminger, Carol S.

1992-01-01

X-ray photoelectron spectroscopy (XPS) has been used to study the surface composition and chemistry of Long Duration Exposure Facility (LDEF) exposed materials including silvered Teflon (Ag/FEP), Kapton, S13GLO paint, quartz crystal monitors (QCM's), carbon fiber/organic matrix composites, and carbon fiber/Al Alloy composites. In each set of samples, silicones were the major contributors to the molecular film accumulated on the LDEF exposed surfaces. All surfaces analyzed have been contaminated with Si, O, and C; most have low levels (less than 1 atom percent) of N, S, and F. Occasionally observed contaminants included Cl, Na, K, P, and various metals. Orange/brown discoloration observed near vent slots in some Ag/FEP blankets were higher in carbon, sulfur, and nitrogen relative to other contamination types. The source of contamination has not been identified, but amine/amide functionalities were detected. It is probable that this same source of contamination account for the low levels of sulfur and nitrogen observed on most LDEF exposed surfaces. XPS, which probes 50 to 100 A in depth, detected the major sample components underneath the contaminant film in every analysis. This probably indicates that the contaminant overlayer is patchy, with significant areas covered by less that 100 A of molecular film. Energy dispersive x-ray spectroscopy (EDS) of LDEF exposed surfaces during secondary electron microscopy (SEM) of the samples confirmed contamination of the surfaces with Si and O. In general, particulates were not observed to develop from the contaminant overlayer on the exposed LDEF material surfaces. However, many SiO2 submicron particles were seen on a masked edge of an Ag/FEP blanket. In some cases such as the carbon fiber/organic matrix composites, interpretation of the contamination data was hindered by the lack of good laboratory controls. Examination of laboratory controls for the carbon fiber/Al alloy composites showed that preflight contamination was the most significant factor for all the contaminants generally detected at less than 1 atom percent, or detected only occasionally (i.e., all but Si, O, and C). Flight control surfaces, including sample backsides not exposed to space radiation or atomic oxygen flux, have accumulated some contamination on flight (compared to laboratory controls), but experimentally, the LDEF exposed surface contamination levels are generally higher for the contaminants Si and O. For most materials analyzed, Si contamination levels were higher on the leading edge surfaces than on the trailing edge surfaces. This was true even for the composite samples where considerable atomic oxygen erosion of the leading edge surfaces was observed by SEM. It is probable that the return flux associated with atmospheric backscatter resulted in enhanced deposition of silicones and other contaminants on the leading edge flight surfaces relative to the trailing edge. Although the Si concentration data suggested greater on-flight deposition of contaminants on the leading edge surfaces, the XPS analyses did not conclusively show different relative total thicknesses of flight deposited contamination for leading and trailing edge surfaces. It is possible that atomic oxygen reactions on the leading edge resulted in greater volatilization of the carbon component of the deposited silicones, effectively 'thinning' the leading edge deposited overlayer. Unlike other materials, exposed polymers such as Kapton and FEP-type Teflon had very low contamination on the leading edge surfaces. SEM evidence showed that undercutting of the contaminant overlayer and damaged polymer layers occurred during atomic oxygen erosion, which would enhance loss of material from the exposed surface.

Measurements of Gas-Wall Partitioning of Oxidized Species in Environmental Smog Chambers and Teflon Sampling Lines

NASA Astrophysics Data System (ADS)

Krechmer, J.; Pagonis, D.; Ziemann, P. J.; Jimenez, J. L.

2015-12-01

Environmental "smog" chambers have played an integral role in atmospheric aerosol research for decades. Recently, many works have demonstrated that the loss of gas-phase material to fluorinated ethylene propylene (FEP) chamber walls can have significant effects on secondary organic aerosol (SOA) yield results. The effects of gas-wall partitioning on highly oxidized species is still controversial, however. In this work we performed a series of experiments examining the losses of oxidized gas-phase compounds that were generated in-situ­ in an environmental chamber. The loss of species to the walls was measured using three chemical ionization mass spectrometry techniques: proton-transfer-reaction (PTR), nitrate (NO3-) ion, and iodide (I-). Many oxidized species have wall loss timescales ranging between 15 to 45 minutes and scale according to the molecule's estimated saturation concentration c* and functional groups. By comparing results of the different techniques, and in particular by the use of the "wall-less" NO3- source, we find that measuring species with high chamber wall-loss rates is complicated by the use of a standard ion-molecule reaction (IMR) region, as well as long Teflon sampling lines, which can be important sinks for gas-phase species. This effect is observed even for semi-volatile species and could have significant effects on ambient sampling techniques that make highly time-resolved measurements using long sampling lines, such as eddy covariance measurements.

Evaluation of sample recovery of malodorous livestock gases from air sampling bags, solid-phase microextraction fibers, Tenax TA sorbent tubes, and sampling canisters.

PubMed

Koziel, Jacek A; Spinhirne, Jarett P; Lloyd, Jenny D; Parker, David B; Wright, Donald W; Kuhrt, Fred W

2005-08-01

Odorous gases associated with livestock operations are complex mixtures of hundreds if not thousands of compounds. Research is needed to know how best to sample and analyze these compounds. The main objective of this research was to compare recoveries of a standard gas mixture of 11 odorous compounds from the Carboxen/PDMS 75-microm solid-phase microextraction fibers, polyvinyl fluoride (PVF; Tedlar), fluorinated ethylene propylene copolymer (FEP; Teflon), foil, and polyethylene terephthalate (PET; Melinex) air sampling bags, sorbent 2,b-diphenylene-oxide polymer resin (Tenax TA) tubes, and standard 6-L Stabilizer sampling canisters after sample storage for 0.5, 24, and 120 (for sorbent tubes only) hrs at room temperature. The standard gas mixture consisted of 7 volatile fatty acids (VFAs) from acetic to hexanoic, and 4 semivolatile organic compounds including p-cresol, indole, 4-ethylphenol, and 2'-aminoacetophenone with concentrations ranging from 5.1 ppb for indole to 1270 ppb for acetic acid. On average, SPME had the highest mean recovery for all 11 gases of 106.2%, and 98.3% for 0.5- and 24-hr sample storage time, respectively. This was followed by the Tenax TA sorbent tubes (94.8% and 88.3%) for 24 and 120 hr, respectively; PET bags (71.7% and 47.2%), FEP bags (75.4% and 39.4%), commercial Tedlar bags (67.6% and 22.7%), in-house-made Tedlar bags (47.3% and 37.4%), foil bags (16.4% and 4.3%), and canisters (4.2% and 0.5%), for 0.5 and 24 hr, respectively. VFAs had higher recoveries than semivolatile organic compounds for all of the bags and canisters. New FEP bags and new foil bags had the lowest and the highest amounts of chemical impurities, respectively. New commercial Tedlar bags had measurable concentrations of N,N-dimethyl acetamide and phenol. Foil bags had measurable concentrations of acetic, propionic, butyric, valeric, and hexanoic acids.

Techniques for Measuring Low Earth Orbital Atomic Oxygen Erosion of Polymers

NASA Technical Reports Server (NTRS)

deGroh, Kim K.; Banks, Bruce A.; Demko, Rikako

2002-01-01

Polymers such as polyimide Kapton and Teflon FEP (fluorinated ethylene propylene) are commonly used spacecraft materials due to their desirable properties such as flexibility, low density, and in the case of FEP, a low solar absorptance and high thermal emittance. Polymers on the exterior of spacecraft in the low Earth orbit (LEO) environment are exposed to energetic atomic oxygen. Atomic oxygen reaction with polymers causes erosion, which is a threat to spacecraft durability. It is therefore important to understand the atomic oxygen erosion yield (E, the volume loss per incident oxygen atom) of polymers being considered in spacecraft design. The most common technique for determining E is through mass loss measurements. For limited duration exposure experiments, such as shuttle experiments, where the atomic oxygen fluence is often so low that mass loss measurements can not produce acceptable uncertainties, recession measurements based on atomic force microscopy analyses can be used. Equally necessary to knowing the mass loss or recession depth for determining the erosion yield of polymers is the knowledge of the atomic oxygen fluence that the polymers were exposed to in space. This paper discusses the procedures and relevant issues for mass loss and recession depth measurements for passive atomic oxygen erosion yield characterization of polymers, along with techniques for active atomic oxygen fluence and erosion characterization. One active atomic oxygen erosion technique discussed is a new technique based on optical measurements. Details including the use of both semi-transparent and opaque polymers for active erosion measurement are reviewed.

High resolution masks for ion milling pores through substrates of biological interest

NASA Technical Reports Server (NTRS)

Donovan, S. S.

1978-01-01

The feasibility was investigated of electrochemically oxidizing vapor deposited aluminum coatings to produce porous aluminum oxide coatings with submicron pore diameters and with straight channels normal to the substrate surface. Porous aluminum oxide coatings were produced from vapor deposited aluminum coatings on thin stainless steel (304), copper, Teflon (FEP) and Kapton substrates and also on pure aluminum substrates. Scanning electron microscope examination indicated that porous oxide coatings can be produced with straight channels, appropriate pore diameters and none or minimal intervening residual aluminum. The oxide coatings on the copper and Kapton substrates had the straightest channels and in general were superior to those fabricated on the other substrate materials. For oxide coatings fabricated at 600 V and 300 V, pore diameters were 0.4-0.6, and 0.3 micron with center-to-center spacing of 0.7-0.8, and 0.4 micron, respectively. Estimated direct labor and materials costs to prepare an oxide mask is anticipated to be about $4-$6 per square foot.

Secondary electron emission from a dielectric film subjected to an electric field. M.S. Thesis

NASA Technical Reports Server (NTRS)

Quoc-Nguyen, N.

1977-01-01

An electric field in the range of 0.3,3.3 kV/mm is created normal to a thin film FEP teflon sample which accumulates potential of up to 8.8, 13.7 or 18.3 kV when exposed to an electron beam having energy of 10.0, 15.0 or 20.0 kV, respectively. It is found that the secondary electron emission from the charged sample varies with field. The threshold voltage, at which the secondary electron emission coefficient sigma is unity, drops down from a low field value of 13.73 kV to a high field value of 13.11 kV for a 15.0 kV beam. A computational technique was developed that generates equipotential lines or contours and field vectors above a plane where potential is known. The utilization of conformal transformations allows the extension of the technique to configurations which map into a plane.

Gaseous Elemental Mercury (GEM) Emissions from Snow Surfaces in Northern New York

PubMed Central

Maxwell, J. Alexander; Holsen, Thomas M.; Mondal, Sumona

2013-01-01

Snow surface-to-air exchange of gaseous elemental mercury (GEM) was measured using a modified Teflon fluorinated ethylene propylene (FEP) dynamic flux chamber (DFC) in a remote, open site in Potsdam, New York. Sampling was conducted during the winter months of 2011. The inlet and outlet of the DFC were coupled with a Tekran Model 2537A mercury (Hg) vapor analyzer using a Tekran Model 1110 two port synchronized sampler. The surface GEM flux ranged from −4.47 ng m−2 hr−1 to 9.89 ng m−2 hr−1. For most sample periods, daytime GEM flux was strongly correlated with solar radiation. The average nighttime GEM flux was slightly negative and was not well correlated with any of the measured meteorological variables. Preliminary, empirical models were developed to estimate GEM emissions from snow surfaces in northern New York. These models suggest that most, if not all, of the Hg deposited with and to snow is reemitted to the atmosphere. PMID:23874951

Materials and techniques for spacecraft static charge control

NASA Technical Reports Server (NTRS)

Amore, L. J.; Eagles, A. E.

1977-01-01

An overview of the design, development, fabrication, and testing of transparent conductive coatings and conductive lattices deposited or formed on high resistivity spacecraft dielectric materials to obtain control static charge buildup on spacecraft external surfaces is presented. Fabrication techniques for the deposition of indium/tin oxide coatings and copper grid networks on Kapton and FEP Teflon films and special frit coatings for OSR and solar cell cover glasses are discussed. The techniques include sputtering, photoetching, silkscreening, and mechanical processes. A facility designed and built to simulate the electron plasma at geosynchronous altitudes is described along with test procedures. The results of material characterizations as well as electron irradiation aging effects in this facility for spacecraft polymers treated to control static charge are presented. The data presents results for electron beam energies up to 30 kV and electron current densities of 30 nA/cm squared. Parameters measured include secondary emission, surface leakage, and through the sample currents as a function of primary beam energy and voltage.

Conceptual approach study of a 200 watt per kilogram solar array

NASA Technical Reports Server (NTRS)

Stanhouse, R. W.; Fox, D.; Wilson, W.

1976-01-01

Solar array candidate configurations (flexible rollup, flexible flat-pact, semi-rigid panel, semi-rigid flat-pack) were analyzed with particular attention to the specific power (W/kg) requirement. Two of these configurations (flexible rollup and flexible flat-pack) are capable of delivering specific powers equal to or exceeding the baseline requirement of 200 W/kg. Only the flexible rollup is capable of in-flight retraction and subsequent redeployment. The wrap-around contact photovoltaic cell configuration has been chosen over the conventional cell. The demand for ultra high specific power forces the selection of ultra-thin cells and cover material. Based on density and mass range considerations, it was concluded that 13 micrometers of FEP Teflon is sufficient to protect the cell from a total proton fluency of 2(10 to the 12th power) particles/sq cm over a three-year interplanetary mission. The V-stiffened, lattice boom deployed, flexible substrate rollup array holds the greatest promise of meeting the baseline requirements set for this study.

Solar maximum: Solar array degradation

NASA Technical Reports Server (NTRS)

Miller, T.

1985-01-01

The 5-year in-orbit power degradation of the silicon solar array aboard the Solar Maximum Satellite was evaluated. This was the first spacecraft to use Teflon R FEP as a coverglass adhesive, thus avoiding the necessity of an ultraviolet filter. The peak power tracking mode of the power regulator unit was employed to ensure consistent maximum power comparisons. Telemetry was normalized to account for the effects of illumination intensity, charged particle irradiation dosage, and solar array temperature. Reference conditions of 1.0 solar constant at air mass zero and 301 K (28 C) were used as a basis for normalization. Beginning-of-life array power was 2230 watts. Currently, the array output is 1830 watts. This corresponds to a 16 percent loss in array performance over 5 years. Comparison of Solar Maximum Telemetry and predicted power levels indicate that array output is 2 percent less than predictions based on an annual 1.0 MeV equivalent election fluence of 2.34 x ten to the 13th power square centimeters space environment.

Gaseous elemental mercury (GEM) emissions from snow surfaces in northern New York.

PubMed

Maxwell, J Alexander; Holsen, Thomas M; Mondal, Sumona

2013-01-01

Snow surface-to-air exchange of gaseous elemental mercury (GEM) was measured using a modified Teflon fluorinated ethylene propylene (FEP) dynamic flux chamber (DFC) in a remote, open site in Potsdam, New York. Sampling was conducted during the winter months of 2011. The inlet and outlet of the DFC were coupled with a Tekran Model 2537A mercury (Hg) vapor analyzer using a Tekran Model 1110 two port synchronized sampler. The surface GEM flux ranged from -4.47 ng m(-2) hr(-1) to 9.89 ng m(-2) hr(-1). For most sample periods, daytime GEM flux was strongly correlated with solar radiation. The average nighttime GEM flux was slightly negative and was not well correlated with any of the measured meteorological variables. Preliminary, empirical models were developed to estimate GEM emissions from snow surfaces in northern New York. These models suggest that most, if not all, of the Hg deposited with and to snow is reemitted to the atmosphere.

A new plant chamber facility PLUS coupled to the atmospheric simulation chamber SAPHIR

NASA Astrophysics Data System (ADS)

Hohaus, T.; Kuhn, U.; Andres, S.; Kaminski, M.; Rohrer, F.; Tillmann, R.; Wahner, A.; Wegener, R.; Yu, Z.; Kiendler-Scharr, A.

2015-11-01

A new PLant chamber Unit for Simulation (PLUS) for use with the atmosphere simulation chamber SAPHIR (Simulation of Atmospheric PHotochemistry In a large Reaction Chamber) has been build and characterized at the Forschungszentrum Jülich GmbH, Germany. The PLUS chamber is an environmentally controlled flow through plant chamber. Inside PLUS the natural blend of biogenic emissions of trees are mixed with synthetic air and are transferred to the SAPHIR chamber where the atmospheric chemistry and the impact of biogenic volatile organic compounds (BVOC) can be studied in detail. In PLUS all important enviromental parameters (e.g. temperature, PAR, soil RH etc.) are well-controlled. The gas exchange volume of 9.32 m3 which encloses the stem and the leafes of the plants is constructed such that gases are exposed to FEP Teflon film and other Teflon surfaces only to minimize any potential losses of BVOCs in the chamber. Solar radiation is simulated using 15 LED panels which have an emission strength up to 800 μmol m-2 s-1. Results of the initial characterization experiments are presented in detail. Background concentrations, mixing inside the gas exchange volume, and transfer rate of volatile organic compounds (VOC) through PLUS under different humidity conditions are explored. Typical plant characteristics such as light and temperature dependent BVOC emissions are studied using six Quercus Ilex trees and compared to previous studies. Results of an initial ozonolysis experiment of BVOC emissions from Quercus Ilex at typical atmospheric concentrations inside SAPHIR are presented to demonstrate a typical experimental set up and the utility of the newly added plant chamber.

A technique for synergistic atomic oxygen and vacuum ultraviolet radiation durability evaluation of materials for use in LEO

NASA Technical Reports Server (NTRS)

Rutledge, Sharon K.; Banks, Bruce A.

1996-01-01

Material erosion data collected during flight experiments such as the Environmental Oxygen Interaction with Materials (EOIM)-3 and the Long Duration Exposure Facility (LDEF) have raised questions as to the sensitivity of material erosion to levels of atomic oxygen exposure and vacuum ultraviolet (VUV) radiation. The erosion sensitivity of some materials such as FEP Teflon used as a thermal control material on satellites in low Earth orbit (LEO), is particularly important but difficult to determine. This is in large part due to the inability to hold all but one exposure parameter constant during a flight experiment. This is also difficult to perform in a ground based facility, because often the variation of the level of atomic oxygen or VUV radiation also results in a change in the level of the other parameter. A facility has been developed which allows each parameter to be changed almost independently and offer broad area exposure. The resulting samples can be made large enough for mechanical testing. The facility uses an electron cyclotron resonance plasma source to provide the atomic oxygen. A series of glass plates is used to focus the atomic oxygen while filtering the VUV radiation from the plasma source. After filtering, atomic oxygen effective flux levels can still be measured which are as high as 7 x 10(exp 15) atoms/cm(exp 2)-sec which is adequate for accelerated testing. VUV radiation levels after filtering can be as low as 0.3 suns. Additional VUV suns can be added with the use of deuterium lamps which allow the VUV level to be changed while keeping the flux of atomic oxygen constant. This paper discusses the facility, and results from exposure of Kapton and FEP at pre-determined atomic oxygen flux and VUV sun levels.

Export of FepA::PhoA fusion proteins to the outer membrane of Escherichia coli K-12.

PubMed

Murphy, C K; Klebba, P E

1989-11-01

A library of fepA::phoA gene fusions was generated in order to study the structure and secretion of the Escherichia coli K-12 ferric enterobactin receptor, FepA. All of the fusion proteins contained various lengths of the amino-terminal portion of FepA fused in frame to the catalytic portion of bacterial alkaline phosphatase. Localization of FepA::PhoA fusion proteins in the cell envelope was dependent on the number of residues of mature FepA present at the amino terminus. Hybrids containing up to one-third of the amino-terminal portion of FepA fractionated with their periplasm, while those containing longer sequences of mature FepA were exported to the outer membrane. Outer membrane-localized fusion proteins expressed FepA sequences on the external face of the outer membrane and alkaline phosphatase moieties in the periplasmic space. From sequence determinations of the fepA::phoA fusion joints, residues within FepA which may be exposed on the periplasmic side of the outer membrane were identified.

FEATURES, EVENTS, AND PROCESSES: SYSTEM-LEVEL AND CRITICALITY

DOE Office of Scientific and Technical Information (OSTI.GOV)

D.L. McGregor

The primary purpose of this Analysis/Model Report (AMR) is to identify and document the screening analyses for the features, events, and processes (FEPs) that do not easily fit into the existing Process Model Report (PMR) structure. These FEPs include the 3 1 FEPs designated as System-Level Primary FEPs and the 22 FEPs designated as Criticality Primary FEPs. A list of these FEPs is provided in Section 1.1. This AMR (AN-WIS-MD-000019) documents the Screening Decision and Regulatory Basis, Screening Argument, and Total System Performance Assessment (TSPA) Disposition for each of the subject Primary FEPs. This AMR provides screening information and decisionsmore » for the TSPA-SR report and provides the same information for incorporation into a project-specific FEPs database. This AMR may also assist reviewers during the licensing-review process.« less

Monitoring and forecasting of great radiation hazards for spacecraft and aircrafts by online cosmic ray data

NASA Astrophysics Data System (ADS)

Dorman, L. I.

2005-11-01

We show that an exact forecast of great radiation hazard in space, in the magnetosphere, in the atmosphere and on the ground can be made by using high-energy particles (few GeV/nucleon and higher) whose transportation from the Sun is characterized by a much bigger diffusion coefficient than for small and middle energy particles. Therefore, high energy particles come from the Sun much earlier (8-20 min after acceleration and escaping into solar wind) than the main part of smaller energy particles (more than 30-60 min later), causing radiation hazard for electronics and personal health, as well as spacecraft and aircrafts. We describe here principles of an automatic set of programs that begin with "FEP-Search", used to determine the beginning of a large FEP event. After a positive signal from "FEP-Search", the following programs start working: "FEP-Research/Spectrum", and then "FEP-Research/Time of Ejection", "FEP-Research /Source" and "FEP-Research/Diffusion", which online determine properties of FEP generation and propagation. On the basis of the obtained information, the next set of programs immediately start to work: "FEP-Forecasting/Spacecrafts", "FEP-Forecasting/Aircrafts", "FEP-Forecasting/Ground", which determine the expected differential and integral fluxes and total fluency for spacecraft on different orbits, aircrafts on different airlines, and on the ground, depending on altitude and cutoff rigidity. If the level of radiation hazard is expected to be dangerous for high level technology or/and personal health, the following programs will be used "FEP-Alert/Spacecrafts", "FEP-Alert/ Aircrafts", "FEP-Alert/Ground".

A new plant chamber facility, PLUS, coupled to the atmosphere simulation chamber SAPHIR

NASA Astrophysics Data System (ADS)

Hohaus, T.; Kuhn, U.; Andres, S.; Kaminski, M.; Rohrer, F.; Tillmann, R.; Wahner, A.; Wegener, R.; Yu, Z.; Kiendler-Scharr, A.

2016-03-01

A new PLant chamber Unit for Simulation (PLUS) for use with the atmosphere simulation chamber SAPHIR (Simulation of Atmospheric PHotochemistry In a large Reaction Chamber) has been built and characterized at the Forschungszentrum Jülich GmbH, Germany. The PLUS chamber is an environmentally controlled flow-through plant chamber. Inside PLUS the natural blend of biogenic emissions of trees is mixed with synthetic air and transferred to the SAPHIR chamber, where the atmospheric chemistry and the impact of biogenic volatile organic compounds (BVOCs) can be studied in detail. In PLUS all important environmental parameters (e.g., temperature, photosynthetically active radiation (PAR), soil relative humidity (RH)) are well controlled. The gas exchange volume of 9.32 m3 which encloses the stem and the leaves of the plants is constructed such that gases are exposed to only fluorinated ethylene propylene (FEP) Teflon film and other Teflon surfaces to minimize any potential losses of BVOCs in the chamber. Solar radiation is simulated using 15 light-emitting diode (LED) panels, which have an emission strength up to 800 µmol m-2 s-1. Results of the initial characterization experiments are presented in detail. Background concentrations, mixing inside the gas exchange volume, and transfer rate of volatile organic compounds (VOCs) through PLUS under different humidity conditions are explored. Typical plant characteristics such as light- and temperature- dependent BVOC emissions are studied using six Quercus ilex trees and compared to previous studies. Results of an initial ozonolysis experiment of BVOC emissions from Quercus ilex at typical atmospheric concentrations inside SAPHIR are presented to demonstrate a typical experimental setup and the utility of the newly added plant chamber.

International Test Program for Synergistic Atomic Oxygen and Vacuum Ultraviolet Radiation Exposure of Spacecraft Materials

NASA Technical Reports Server (NTRS)

Miller, Sharon K.

2001-01-01

The components and materials of spacecraft in low Earth orbit can degrade in thermal and optical performance through interaction with atomic oxygen and vacuum ultraviolet (VUV) radiation, which are predominant in low Earth orbit. Because of the importance of low Earth orbit durability and performance to manufacturers and users, an international test program for assessing the durability of spacecraft materials and components was initiated. Initial tests at the NASA Glenn Research Center consisted of exposure of samples representing a variety of thermal control paints, multilayer insulation materials, and Sun sensors that have been used in space. Materials donated from various international sources were tested alongside materials whose performance is well known, such as Teflon FEP, Kapton H, or Z-93-P white paint. The optical, thermal, or mass loss data generated during the tests were then provided to the participating material suppliers. Data were not published unless the participant donating the material consented to publication. The test program is intended to give spacecraft builders and users a better understanding of degradation processes and effects so that they can improve their predictions of spacecraft performance.

Mass spectra of neutral particles released during electrical breakdown of thin polymer films

NASA Technical Reports Server (NTRS)

Kendall, B. R. F.

1985-01-01

A special type of time-of-flight mass spectrometer triggered from the breakdown event was developed to study the composition of the neutral particle flux released during the electrical breakdown of polymer films problem. Charge is fed onto a metal-backed polymer surface by a movable smooth platinum contact. A slowly increasing potential from a high-impedance source is applied to the contact until breakdown occurs. The breakdown characteristics is made similar to those produced by an electron beam charging system operating at similar potentials. The apparatus showed that intense instantaneous fluxes of neutral particles are released from the sites of breakdown events. For Teflon FEP films of 50 and 75 microns thickness the material released consists almost entirely of fluorocarbon fragments, some of them having masses greater than 350 atomic mass units amu, while the material released from a 50 micron Kapton film consists mainly of light hydrocarbons with masses at or below 44 amu, with additional carbon monoxide and carbon dioxide. The apparatus is modified to allow electron beam charging of the samples.

Role of the Twin-Arginine Translocation Pathway in Staphylococcus▿ †

PubMed Central

Biswas, Lalitha; Biswas, Raja; Nerz, Christiane; Ohlsen, Knut; Schlag, Martin; Schäfer, Tina; Lamkemeyer, Tobias; Ziebandt, Anne-Kathrin; Hantke, Klaus; Rosenstein, Ralf; Götz, Friedrich

2009-01-01

In Staphylococcus, the twin-arginine translocation (Tat) pathway is present only in some species and is composed of TatA and TatC. The tatAC operon is associated with the fepABC operon, which encodes homologs to an iron-binding lipoprotein, an iron-dependent peroxidase (FepB), and a high-affinity iron permease. The FepB protein has a typical twin-arginine (RR) signal peptide. The tat and fep operons constitute an entity that is not present in all staphylococcal species. Our analysis was focused on Staphylococcus aureus and S. carnosus strains. Tat deletion mutants (ΔtatAC) were unable to export active FepB, indicating that this enzyme is a Tat substrate. When the RR signal sequence from FepB was fused to prolipase and protein A, their export became Tat dependent. Since no other protein with a Tat signal could be detected, the fepABC-tatAC genes comprise not only a genetic but also a functional unit. We demonstrated that FepABC drives iron import, and in a mouse kidney abscess model, the bacterial loads of ΔtatAC and Δtat-fep mutants were decreased. For the first time, we show that the Tat pathway in S. aureus is functional and serves to translocate the iron-dependent peroxidase FepB. PMID:19633084

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Hyo-Jin; Lee, Kang-Lok; Kim, Kyoung-Dong

Iron homeostasis is tightly regulated since iron is an essential but toxic element in the cell. The GATA-type transcription factor Fep1 and its orthologs contribute to iron homeostasis in many fungi by repressing genes for iron uptake when intracellular iron is high. Even though the function and interaction partners of Fep1 have been elucidated extensively In Schizosaccharomyces pombe, the mechanism behind iron-sensing by Fep1 remains elusive. It has been reported that Fep1 interacts with Fe-S-containing monothiol glutaredoxin Grx4 and Grx4-Fra2 complex. In this study, we demonstrate that Fep1 also binds iron, in the form of Fe-S cluster. Spectroscopic and biochemicalmore » analyses of as isolated and reconstituted Fep1 suggest that the dimeric Fep1 binds Fe-S clusters. The mutation study revealed that the cluster-binding depended on the conserved cysteines located between the two zinc fingers in the DNA binding domain. EPR analyses revealed [Fe-S]-specific peaks indicative of mixed presence of [2Fe-2S], [3Fe-4S], or [4Fe-4S]. The finding that Fep1 is an Fe-S protein fits nicely with the model that the Fe-S-trafficking Grx4 senses intracellular iron environment and modulates the activity of Fep1. - Highlights: • Fep1, a prototype fungal iron uptake regulator, was isolated stably from Schizosaccharomyces pombe. • Fep1 exhibits UV–visible absorption spectrum, characteristic of [Fe-S] proteins. • The iron and sulfide contents in purified or reconstituted Fep1 also support [Fe-S]. • The conserved cysteines are critical for [Fe-S]-binding. • EPR spectra at 5 K and 123 K suggest a mixed population of [Fe-S].« less

Evaluation of Surface Modification as a Lunar Dust Mitigation Strategy for Thermal Control Surfaces

NASA Technical Reports Server (NTRS)

Gaier, James R.; Waters, Deborah L.; Misconin, Robert M.; Banks, Bruce A.; Crowder, Mark

2011-01-01

Three surface treatments were evaluated for their ability to lower the adhesion between lunar simulant dust and AZ93, AlFEP, and AgFEP thermal control surfaces under simulated lunar conditions. Samples were dusted in situ and exposed to a standardized puff of nitrogen gas. Thermal performance before dusting, after dusting, and after part of the dust was removed by the puff of gas, were compared to perform the assessment. None of the surface treatments was found to significantly affect the adhesion of lunar simulants to AZ93 thermal control paint. Oxygen ion beam texturing also did not lower the adhesion of lunar simulant dust to AlFEP or AgFEP. But a workfunction matching coating and a proprietary Ball Aerospace surface treatment were both found to significantly lower the adhesion of lunar simulants to AlFEP and AgFEP. Based on these results, it is recommended that all these two techniques be further explored as dust mitigation coatings for AlFEP and AgFEP thermal control surfaces.

The iron uptake repressor Fep1 in the fission yeast binds Fe-S cluster through conserved cysteines.

PubMed

Kim, Hyo-Jin; Lee, Kang-Lok; Kim, Kyoung-Dong; Roe, Jung-Hye

2016-09-09

Iron homeostasis is tightly regulated since iron is an essential but toxic element in the cell. The GATA-type transcription factor Fep1 and its orthologs contribute to iron homeostasis in many fungi by repressing genes for iron uptake when intracellular iron is high. Even though the function and interaction partners of Fep1 have been elucidated extensively In Schizosaccharomyces pombe, the mechanism behind iron-sensing by Fep1 remains elusive. It has been reported that Fep1 interacts with Fe-S-containing monothiol glutaredoxin Grx4 and Grx4-Fra2 complex. In this study, we demonstrate that Fep1 also binds iron, in the form of Fe-S cluster. Spectroscopic and biochemical analyses of as isolated and reconstituted Fep1 suggest that the dimeric Fep1 binds Fe-S clusters. The mutation study revealed that the cluster-binding depended on the conserved cysteines located between the two zinc fingers in the DNA binding domain. EPR analyses revealed [Fe-S]-specific peaks indicative of mixed presence of [2Fe-2S], [3Fe-4S], or [4Fe-4S]. The finding that Fep1 is an Fe-S protein fits nicely with the model that the Fe-S-trafficking Grx4 senses intracellular iron environment and modulates the activity of Fep1. Copyright © 2016 Elsevier Inc. All rights reserved.

Effect of electron irradiation in vacuum on FEP-A silicon solar cell covers

NASA Technical Reports Server (NTRS)

Marsik, S. J.; Broder, J. D.

1975-01-01

Fluorinated ethylene-propylene-A (FEP-A) covers on silicon solar cells were irradiated with 1-MeV electrons, in vacuum, to an accumulated fluence equivalent to approximately 28 years in synchronous orbit. The effect of irradiation on the light transmittance of FEP-A was checked by measuring the short-circuit current of the cells after each dose increment. The results indicate no apparent overall loss in transmission due to irradiation of FEP-A. Filter wheel measurements revealed some darkening of the FEP-A at the blue end of the spectrum. Although no delamination from the cell surface was observed while in vacuum, embrittlement of FEP-A occurred at the accumulated dose.

Analysis of International Space Station Vehicle Materials on MISSE 6

NASA Technical Reports Server (NTRS)

Finckenor, Miria; Golden, Johnny; Kravchenko, Michael; O'Rourke, Mary Jane

2010-01-01

The International Space Station Materials and Processes team has multiple material samples on MISSE 6, 7 and 8 to observe Low Earth Orbit (LEO) environmental effects on Space Station materials. Optical properties, thickness/mass loss, surface elemental analysis, visual and microscopic analysis for surface change are some of the techniques employed in this investigation. Results for the following MISSE 6 samples materials will be presented: deionized water sealed anodized aluminum; Hyzod(tm) polycarbonate used to temporarily protect ISS windows; Russian quartz window material; Beta Cloth with Teflon(tm) reformulated without perfluorooctanoic acid (PFOA), and electroless nickel. Discussion for current and future MISSE materials experiments will be presented. MISSE 7 samples are: more deionized water sealed anodized aluminum, including Photofoil(tm); indium tin oxide (ITO) over-coated Kapton(tm) used as thermo-optical surfaces; mechanically scribed tin-plated beryllium-copper samples for "tin pest" growth (alpha/beta transformation); and beta cloth backed with a black coating rather than aluminization. MISSE 8 samples are: exposed "scrim cloth" (fiberglass weave) from the ISS solar array wing material, protective fiberglass tapes and sleeve materials, and optical witness samples to monitor contamination.

Development of a quantum mechanics-based free-energy perturbation method: use in the calculation of relative solvation free energies.

PubMed

Reddy, M Rami; Singh, U C; Erion, Mark D

2004-05-26

Free-energy perturbation (FEP) is considered the most accurate computational method for calculating relative solvation and binding free-energy differences. Despite some success in applying FEP methods to both drug design and lead optimization, FEP calculations are rarely used in the pharmaceutical industry. One factor limiting the use of FEP is its low throughput, which is attributed in part to the dependence of conventional methods on the user's ability to develop accurate molecular mechanics (MM) force field parameters for individual drug candidates and the time required to complete the process. In an attempt to find an FEP method that could eventually be automated, we developed a method that uses quantum mechanics (QM) for treating the solute, MM for treating the solute surroundings, and the FEP method for computing free-energy differences. The thread technique was used in all transformations and proved to be essential for the successful completion of the calculations. Relative solvation free energies for 10 structurally diverse molecular pairs were calculated, and the results were in close agreement with both the calculated results generated by conventional FEP methods and the experimentally derived values. While considerably more CPU demanding than conventional FEP methods, this method (QM/MM-based FEP) alleviates the need for development of molecule-specific MM force field parameters and therefore may enable future automation of FEP-based calculations. Moreover, calculation accuracy should be improved over conventional methods, especially for calculations reliant on MM parameters derived in the absence of experimental data.

Field evoked potentials in the globus pallidus of non-human primates.

PubMed

Prescott, Ian A; Marino, Robert A; Levy, Ron

2017-07-01

Stimulation-induced field evoked potentials (fEPs) have been described in the basal ganglia output nuclei of patients with Parkinson's disease and dystonia. The aim of this study was to ascertain whether fEPs were inducible in the external (GPe) and internal (GPi) segments of the globus pallidus in normal non-human primates (NHPs). Microelectrode recording and stimulation was performed in the GPe and GPi of 2 healthy NHPs. Stimulus response curves of the fEP response to changing pulse width and amplitude examined strength-duration relationships and allowed for calculation of fEP chronaxie in the GPe and GPi. Traditional localization techniques were also used, including comparison of neuronal firing rates, optic tract activation, and internal capsule activation. Notable differences were seen in the fEPs found in GPe compared to the fEPs found in GPi. The GPe fEP had a smaller chronaxie time and larger positive deflection amplitude compared to GPi. In addition, an earlier negative deflection was identified in both nuclei and a late negative deflection was observed in the GPe in contrast to reported fEPs in patients with movement disorders. fEPs proved valuable as an ancillary method in localizing the GPe and GPi in NHPs and may be useful in the operating room during human GPi deep brain stimulation or pallidotomy procedures. Copyright © 2017 Elsevier Ireland Ltd and Japan Neuroscience Society. All rights reserved.

Development of a large area space solar cell assembly

NASA Technical Reports Server (NTRS)

Spitzer, M. B.

1982-01-01

The development of a large area high efficiency solar cell assembly is described. The assembly consists of an ion implanted silicon solar cell and glass cover. The important attributes of fabrication are the use of a back surface field which is compatible with a back surface reflector, and integration of coverglass application and cell fabrications. Cell development experiments concerned optimization of ion implantation processing of 2 ohm-cm boron-doped silicon. Process parameters were selected based on these experiments and cells with area of 34.3 sq cm wre fabricated. The average AMO efficiency of the twenty-five best cells was 13.9% and the best bell had an efficiency of 14.4%. An important innovation in cell encapsulation was also developed. In this technique, the coverglass is applied before the cell is sawed to final size. The coverglass and cell are then sawed as a unit. In this way, the cost of the coverglass is reduced, since the tolerance on glass size is relaxed, and costly coverglass/cell alignment procedures are eliminated. Adhesive investigated were EVA, FEP-Teflon sheet and DC 93-500. Details of processing and results are reported.

Effects of atomic oxygen on polymeric materials flown on EOIM-3

NASA Technical Reports Server (NTRS)

Kamenetzky, Rachel R.; Linton, Roger C.; Finckenor, Miria M.; Vaughn, Jason A.

1995-01-01

Diverse polymeric materials, including several variations of Kapton, were flown on STS-46 as part of the Evaluation of Oxygen Interaction with Materials Experiment (EOIM-3). These materials were flown in the cargo bay and exposed to the space environment July 31 - August 8, 1992, including 40 hours of direct atomic oxygen impingement. The atomic oxygen exposure was approximately 2.2 x 10(exp 20) atoms/sq cm. Polymeric materials flown on EOIM-3 include coated and uncoated Kapton, Tefzel ETFE, Lexan, FEP and TFE Teflon, bulk Halar and PEEK, S383 silicone and Viton elastomeric seal material. Analyses performed included thickness measurements using Dektak and eddy current methods, mass loss, resistance, permeability, hardness, and FTIR. The effects of stress and the space environment on Kapton were also evaluated. Previous EOIM missions on STS-5 and STS-8 and the Long Duration Exposure Facility also contained polymeric material samples. Data from these previous flights are shown for comparison, as well as ground simulation of space environment effects using both thermal energy flow tubes and 5 eV neutral atomic oxygen beam facilities. Reaction efficiencies for the various atomic oxygen exposure conditions are discussed.

One-year follow-up study of first suicide attempts in first episode psychosis: Personality traits and temporal pattern.

PubMed

Canal-Rivero, Manuel; Barrigón, Maria Luisa; Perona-Garcelán, Salvador; Rodriguez-Testal, Juan F; Giner, Lucas; Obiols-Llandrich, Jordi E; Ruiz-Veguilla, Miguel

2016-11-01

The highest suicide rates occur after psychiatric hospitalization or soon after discharge. In addition to other factors, personality traits have been suggested as predictors of suicide attempts (SA) after first episode psychosis (FEP). In this study we examined their temporal pattern and the influence of personality traits on first suicide attempts (fSA) during one year after FEP. One-year follow-up of 65 FEP patients. Bivariate and multivariable analyses were performed to explore the relationship between personality traits and fSA. This analysis was also adjusted for a set of sociodemographic, clinical and psychopathological variables. fSAs in the six months following FEP were predicted by higher scores in passive-dependent personality traits (OR = 2.42, 95% CI = 1.15-5.09) and severity of symptoms at onset (OR = 2.00, 95% CI = 1.07-3.76). Severity of symptoms at onset (OR = 2.71, CI = 1.15-6.39) was the most significant predictor of fSA from six to twelve months after FEP. Seventy percent of fSA occurred during the first six months after FEP, decreasing considerably afterwards. Our study suggests that personality traits play a role in fSA after FEP. Specifically, passive-dependent personality traits emerged as a predictor of fSA in the six months following FEP. Severity of symptoms at onset predicted early and late first suicide attempts. We also found that risk of fSA is highest during the six months following FEP. These results can contribute to the implementation of prevention program. Copyright © 2016 Elsevier Inc. All rights reserved.

Staphylococcus aureus FepA and FepB proteins drive heme iron utilization in Escherichia coli.

PubMed

Turlin, Evelyne; Débarbouillé, Michel; Augustyniak, Katarzyna; Gilles, Anne-Marie; Wandersman, Cécile

2013-01-01

EfeUOB-like tripartite systems are widespread in bacteria and in many cases they are encoded by genes organized into iron-regulated operons. They consist of: EfeU, a protein similar to the yeast iron permease Ftrp1; EfeO, an extracytoplasmic protein of unknown function and EfeB, also an extracytoplasmic protein with heme peroxidase activity, belonging to the DyP family. Many bacterial EfeUOB systems have been implicated in iron uptake, but a prefential iron source remains undetermined. Nevertheless, in the case of Escherichia coli, the EfeUOB system has been shown to recognize heme and to allow extracytoplasmic heme iron extraction via a deferrochelation reaction. Given the high level of sequence conservations between EfeUOB orthologs, we hypothesized that heme might be the physiological iron substrate for the other orthologous systems. To test this hypothesis, we undertook characterization of the Staphylococcus aureus FepABC system. Results presented here indicate: i) that the S. aureus FepB protein binds both heme and PPIX with high affinity, like EfeB, the E. coli ortholog; ii) that it has low peroxidase activity, comparable to that of EfeB; iii) that both FepA and FepB drive heme iron utilization, and both are required for this activity and iv) that the E. coli FepA ortholog (EfeO) cannot replace FepA in FepB-driven iron release from heme indicating protein specificity in these activities. Our results show that the function in heme iron extraction is conserved in the two orthologous systems.

Salmonella typhimurium IroN and FepA Proteins Mediate Uptake of Enterobactin but Differ in Their Specificity for Other Siderophores

PubMed Central

Rabsch, Wolfgang; Voigt, Wolfgang; Reissbrodt, Rolf; Tsolis, Renée M.; Bäumler, Andreas J.

1999-01-01

Salmonella typhimurium possesses two outer membrane receptor proteins, IroN and FepA, which have been implicated in the uptake of enterobactin. To determine whether both receptors have identical substrate specificities, fepA and iroN mutants and a double mutant were characterized. While both receptors transported enterobactin, the uptake of corynebactin and myxochelin C was selectively mediated by IroN and FepA, respectively. PMID:10348879

Facial emotion perception in schizophrenia: Does sex matter?

PubMed

Mote, Jasmine; Kring, Ann M

2016-06-22

To review the literature on sex differences in facial emotion perception (FEP) across the schizophrenia spectrum. We conducted a systematic review of empirical articles that were included in five separate meta-analyses of FEP across the schizophrenia spectrum, including meta-analyses that predominantly examined adults with chronic schizophrenia, people with early (onset prior to age 18) or recent-onset (experiencing their first or second psychotic episode or illness duration less than 2 years) schizophrenia, and unaffected first-degree relatives of people with schizophrenia. We also examined articles written in English (from November 2011 through June 2015) that were not included in the aforementioned meta-analyses through a literature search in the PubMed database. All relevant articles were accessed in full text. We examined all studies to determine the sample sizes, diagnostic characteristics, demographic information, methodologies, results, and whether each individual study reported on sex differences. The results from the meta-analyses themselves as well as the individual studies are reported in tables and text. We retrieved 134 articles included in five separate meta-analyses and the PubMed database that examined FEP across the schizophrenia spectrum. Of these articles, 38 examined sex differences in FEP. Thirty of these studies did not find sex differences in FEP in either chronically ill adults with schizophrenia, early-onset or recently diagnosed people with schizophrenia, or first-degree relatives of people with schizophrenia. Of the eight studies that found sex differences in FEP, three found that chronically ill women outperformed men, one study found that girls with early-onset schizophrenia outperformed boys, and two studies found that women (including first-degree relatives, adults with schizophrenia, and the healthy control group) outperformed men on FEP tasks. In total, six of the eight studies that examined sex differences in FEP found that women outperformed men across the schizophrenia spectrum. Evidence to date suggests few sex differences in FEP in schizophrenia; both men and women across the schizophrenia spectrum have deficits in FEP.

F19. TELOMERE SHORTENING IN YOUNG PEOPLE WITH FIRST EPISODE PSYCHOSIS: A 12-MONTH FOLLOW-UP STUDY

PubMed Central

Fraguas, David; Recio, Sandra; Diaz-Caneja, Covadonga M; Blasco, Maria A; Moisés, Ana Carolina; Arango, Celso

2018-01-01

Abstract Background Short telomere length is a biomarker of cell oxidation and aging. Patients with first-episode psychosis (FEP) have been reported to have shorter telomeres than healthy controls (HC), suggesting that there is a premature and accelerated cellular aging in FEP. However, there are not data on longitudinal changes of telomere length in people with FEP relative to HC. We present preliminary results on 1-year longitudinal changes in peripheral blood mononuclear cells (PBMCs) telomere length and the proportion of PBMCs with short telomeres in young people with FEP and HC. Methods 16 young patients with FEP (43.8% female, mean age 17.9 years) and 21 young HC (61.9% female, mean age 16.6 years) were enrolled in the study. PBMCs telomere length and the proportion of PBMCs with short telomeres (i.e. <3kb) were determined using high-throughput quantitative fluorescence in situ hybridization (HT Q-FISH) at baseline (16 patients with FEP and 21 HC) and 12-month follow-up (4 patients with FEP and 4 HC). Results At baseline, we did not find significant differences in telomere length nor in proportion of PBMCs with short telomeres between FEP patients and HC. During the one-year follow-up, we found a significantly greater loss of telomere length (p=0.019; explained variance=69.7%) and a non-significantly trend for greater increase in the proportion of PBMCs with short telomeres (p=0.097; explained variance=45.5%) in patients with FEP than in HC. Discussion Telomere length changes during the first years of the illness can represent an early marker of accelerated cellular aging in patients with first-episode psychosis.

Functional Magnetic Resonance Imaging Correlates of First-Episode Psychoses during Attentional and Memory Task Performance.

PubMed

Del Casale, Antonio; Kotzalidis, Georgios D; Rapinesi, Chiara; Sorice, Serena; Girardi, Nicoletta; Ferracuti, Stefano; Girardi, Paolo

2016-01-01

The nature of the alteration of the response to cognitive tasks in first-episode psychosis (FEP) still awaits clarification. We used activation likelihood estimation, an increasingly used method in evaluating normal and pathological brain function, to identify activation changes in functional magnetic resonance imaging (fMRI) studies of FEP during attentional and memory tasks. We included 11 peer-reviewed fMRI studies assessing FEP patients versus healthy controls (HCs) during performance of attentional and memory tasks. Our database comprised 290 patients with FEP, matched with 316 HCs. Between-group analyses showed that HCs, compared to FEP patients, exhibited hyperactivation of the right middle frontal gyrus (Brodmann area, BA, 9), right inferior parietal lobule (BA 40), and right insula (BA 13) during attentional task performances and hyperactivation of the left insula (BA 13) during memory task performances. Right frontal, parietal, and insular dysfunction during attentional task performance and left insular dysfunction during memory task performance are significant neural functional FEP correlates. © 2016 S. Karger AG, Basel.

Density and mechanical properties of calcium aluminate cement

NASA Astrophysics Data System (ADS)

Ahmed, Syed Taqi Uddin; Ahmmad, Shaik Kareem

2018-04-01

Calcium aluminate cements are a special type of cements which have their composition mainly dominated by the presence of Monocalcium Aluminates. In the present paper for the first time we have shown theoretical density and elastic constants for various calcium aluminate cements. The density of the present CAS decrease with aluminates presents in the cement. Using the density data, the elastic moduli namely Young's modulus, bulk and shear modulus show strong linear dependence as a function of compositional parameter.

Antipsychotic Treatment Reduces Indices of Oxidative Stress in First-Episode Psychosis Patients

PubMed Central

Haring, Liina; Vasar, Eero; Vasar, Veiko; Zilmer, Mihkel

2016-01-01

38 first-episode psychosis (FEP) patients and 37 control subjects were recruited for the study of indices of oxidative stress (OxS). The main purpose of the study was to compare the OxS statuses (serum total antioxidant capacity (TAC), total level of peroxides (TPX), oxidative stress index (OSI), and ratio oxidized methionine (Met-SO) to methionine (Met)) between antipsychotic-naïve FEP patients and individuals without a history of psychiatric disorders. Subsequently, the impact of 7-month antipsychotic treatment was evaluated on the OxS status in FEP patients. An attempt was made to assess links between OxS signature and inflammation markers. The oxidative stress indices remained generally unchanged in antipsychotic-naïve FEP patients compared to control subjects. Despite that, there was a significant correlation between the levels of TPX and EGF (endothelial growth factor) in FEP patients. This correlation disappeared after antipsychotic treatment of FEP patients. Moreover, antipsychotic treatment was associated with a significant reduction in OxS indices, including TPX, OSI, and ratio between Met-SO and Met. By contrast, in chronic SCZ patients we established a significant high-grade OxS. In conclusion, the markers of total antioxidative capacity, lipid peroxidation, and protein oxidation revealed no high-grade OxS in FEP patients. Nevertheless, antipsychotic treatment induced a considerable anti-inflammatory effect. OxS levels were also significantly decreased if compared in FEP patients before and after antipsychotic treatment. PMID:27528889

Analysis, development and testing of a fixed tilt solar collector employing reversible Vee-Trough reflectors and vacuum tube receivers

NASA Technical Reports Server (NTRS)

Selcuk, M. K.

1979-01-01

The Vee-Trough/Vacuum Tube Collector (VTVTC) aimed to improve the efficiency and reduce the cost of collectors assembled from evacuated tube receivers. The VTVTC was analyzed rigorously and a mathematical model was developed to calculate the optical performance of the vee-trough concentrator and the thermal performance of the evacuated tube receiver. A test bed was constructed to verify the mathematical analyses and compare reflectors made out of glass, Alzak and aluminized GEB Teflon. Tests were run at temperatures ranging from 95 to 180 C during the months of April, May, June, July and August 1977. Vee-trough collector efficiencies of 35-40 per cent were observed at an operating temperature of about 175 C. Test results compared well with the calculated values. Test data covering a complete day are presented for selected dates throughout the test season. Predicted daily useful heat collection and efficiency values are presented for a year's duration at operation temperatures ranging from 65 to 230 C. Estimated collector costs and resulting thermal energy costs are presented. Analytical and experimental results are discussed along with an economic evaluation.

Remission and recovery from first-episode psychosis in adults: systematic review and meta-analysis of long-term outcome studies.

PubMed

Lally, John; Ajnakina, Olesya; Stubbs, Brendon; Cullinane, Michael; Murphy, Kieran C; Gaughran, Fiona; Murray, Robin M

2017-12-01

Background Remission and recovery rates for people with first-episode psychosis (FEP) remain uncertain. Aims To assess pooled prevalence rates of remission and recovery in FEP and to investigate potential moderators. Method We conducted a systematic review and meta-analysis to assess pooled prevalence rates of remission and recovery in FEP in longitudinal studies with more than 1 year of follow-up data, and conducted meta-regression analyses to investigate potential moderators. Results Seventy-nine studies were included representing 19072 patients with FEP. The pooled rate of remission among 12301 individuals with FEP was 58% (60 studies, mean follow-up 5.5 years). Higher remission rates were moderated by studies from more recent years. The pooled prevalence of recovery among 9642 individuals with FEP was 38% (35 studies, mean follow-up 7.2 years). Recovery rates were higher in North America than in other regions. Conclusions Remission and recovery rates in FEP may be more favourable than previously thought. We observed stability of recovery rates after the first 2 years, suggesting that a progressive deteriorating course of illness is not typical. Although remission rates have improved over time recovery rates have not, raising questions about the effectiveness of services in achieving improved recovery. © The Royal College of Psychiatrists 2017.

Childhood adversities and clinical symptomatology in first-episode psychosis.

PubMed

Lindgren, Maija; Mäntylä, Teemu; Rikandi, Eva; Torniainen-Holm, Minna; Morales-Muñoz, Isabel; Kieseppä, Tuula; Mantere, Outi; Suvisaari, Jaana

2017-12-01

In addition to severe traumatic experiences, milder, more common childhood adversities reflecting psychosocial burden may also be common in people with psychotic disorders and have an effect on symptomatology and functioning. We explored eleven negative childhood experiences and their influence on clinical symptoms among young adults with first-episode psychosis (FEP, n = 75) and matched population controls (n = 51). Individuals with FEP reported more adversities than controls. Specifically serious conflicts within the family, bullying at school, maternal mental health problems, and one's own and parents' serious illness during childhood were experienced by the patients more often than by controls. In the FEP group, the severity of adversity was associated with increased anxiety, manic, and obsessive-compulsive symptoms, but not with the severity of positive psychotic symptoms. Adversity produced a more pronounced effect on symptoms in male patients than in female patients. To conclude, in line with earlier studies of more chronic psychosis, a majority of the participants with FEP reported exposure to childhood adversities, with the FEP group reporting more adversities than controls. High levels of mood and anxiety symptoms in patients with FEP may be related to cumulative exposure to childhood adversities. This should be taken into account in the treatment for FEP. Copyright © 2017 Elsevier B.V. All rights reserved.

Testing odorants recovery from a novel metallized fluorinated ethylene propylene gas sampling bag.

PubMed

Zhu, Wenda; Koziel, Jacek A; Cai, Lingshuang; Wright, Donald; Kuhrt, Fred

2015-12-01

Industry-standard Tedlar bags for odor sample collection from confined animal feeding operations (CAFOs) have been challenged by the evidence of volatile organic compound (VOC) losses and background interferences. Novel impermeable aluminum foil with a thin layer of fluorinated ethylene propylene (FEP) film on the surface that is in contact with a gas sample was developed to address this challenge. In this research, Tedlar and metallized FEP bags were compared for (a) recoveries of four characteristic CAFO odorous VOCs (ethyl mercaptan, butyric acid, isovaleric acid and p-cresol) after 30 min and 24 hr sample storage time and for (b) chemical background interferences. All air sampling and analyses were performed with solid-phase microextraction (SPME) followed by gas chromatography-mass spectroscopy (GC-MS). Mean target gas sample recoveries from metallized FEP bags were 25.9% and 28.0% higher than those in Tedlar bags, for 30 min and 24 hr, respectively. Metallized FEP bags demonstrated the highest p-cresol recoveries after 30-min and 24-hr storage, 96.1±44.5% and 44.8±10.2%, respectively, among different types of sampling bags reported in previous studies. However, a higher variability was observed for p-cresol recovery with metallized FEP bags. A 0% recovery of ethyl mercaptan was observed with Tedlar bags after 24-hr storage, whereas an 85.7±7.4% recovery was achieved with metallized FEP bags. Recoveries of butyric and isovaleric acids were similar for both bag types. Two major impurities in Tedlar bags' background were identified as N,N-dimethylacetamide and phenol, while backgrounds of metallized FEP bags were significantly cleaner. Reusability of metallized FEP bags was tested. Caution is advised when using polymeric materials for storage of livestock-relevant odorous volatile organic compounds. The odorants loss with storage time confirmed that long-term storage in whole-air form is ill advised. A focused short-term odor sample containment should be biased toward the most inert material available relative to the highest impact target odorant. Metallized FEP was identified as such a material to p-cresol as the highest impact odorant from confined animal feeding operations. Metallized FEP bags have much cleaner background than commercial Tedlar bags do. Significantly higher recoveries of methyl mercaptan and p-cresol were also observed with metallized FEP bags.

Crystal structure control of aluminized clay minerals on the mobility of caesium in contaminated soil environments

NASA Astrophysics Data System (ADS)

Dzene, Liva; Ferrage, Eric; Viennet, Jean-Christophe; Tertre, Emmanuel; Hubert, Fabien

2017-02-01

Radioactive caesium pollution resulting from Fukushima Dai-ichi and Chernobyl nuclear plant accidents involves strong interactions between Cs+ and clays, especially vermiculite-type minerals. In acidic soil environments, such as in Fukushima area, vermiculite is subjected to weathering processes, resulting in aluminization. The crystal structure of aluminized clays and its implications for Cs+ mobility in soils remain poorly understood due to the mixture of these minerals with other clays and organic matter. We performed acidic weathering of a vermiculite to mimic the aluminization process in soils. Combination of structure analysis and Cs+ extractability measurements show that the increase of aluminization is accompanied by an increase in Cs+ mobility. Crystal structure model for aluminized vermiculite is based on the interstratification of unaltered vermiculite layers and aluminized layers within the same particle. Cs+ in vermiculite layers is poorly mobile, while the extractability of Cs+ is greatly enhanced in aluminized layers. The overall reactivity of the weathered clay (cation exchange capacity, Cs+ mobility) is then governed by the relative abundance of the two types of layers. The proposed layer model for aluminized vermiculite with two coexisting populations of caesium is of prime importance for predicting the fate of caesium in contaminated soil environments.

Altered default network resting state functional connectivity in patients with a first episode of psychosis.

PubMed

Alonso-Solís, Anna; Corripio, Iluminada; de Castro-Manglano, Pilar; Duran-Sindreu, Santiago; Garcia-Garcia, Manuel; Proal, Erika; Nuñez-Marín, Fidel; Soutullo, Cesar; Alvarez, Enric; Gómez-Ansón, Beatriz; Kelly, Clare; Castellanos, F Xavier

2012-08-01

Default network (DN) abnormalities have been identified in patients with chronic schizophrenia using "resting state" functional magnetic resonance imaging (R-fMRI). Here, we examined the integrity of the DN in patients experiencing their first episode of psychosis (FEP) compared with sex- and age-matched healthy controls. We collected R-fMRI data from 19 FEP patients (mean age 24.9 ± 4.8 yrs, 14 males) and 19 healthy controls (26.1 ± 4.8 yrs, 14 males) at 3T. Following standard preprocessing, we examined the functional connectivity (FC) of two DN subsystems and the two DN hubs (P<0.0045, corrected). Patients with FEP exhibited abnormal FC that appeared largely restricted to the dorsomedial prefrontal cortex (dMPFC) DN subsystem. Relative to controls, FEP patients exhibited weaker positive FC between dMPFC and posterior cingulate cortex (PCC) and precuneus, extending laterally through the parietal lobe to the posterior angular gyrus. Patients with FEP exhibited weaker negative FC between the lateral temporal cortex and the intracalcarine cortex, bilaterally. The PCC and temporo-parietal junction also exhibited weaker negative FC with the right fusiform gyrus extending to the lingual gyrus and lateral occipital cortex, in FEP patients, compared to controls. By contrast, patients with FEP showed stronger negative FC between the temporal pole and medial motor cortex, anterior precuneus and posterior mid-cingulate cortex. Abnormalities in the dMPFC DN subsystem in patients with a FEP suggest that FC patterns are altered even in the early stages of psychosis. Copyright © 2012 Elsevier B.V. All rights reserved.

Altered Default Network Resting State Functional Connectivity in Patients with a First Episode of Psychosis

PubMed Central

Alonso-Solís, Anna; Corripio, Iluminada; de Castro-Manglano, Pilar; Duran-Sindreu, Santiago; Garcia-Garcia, Manuel; Proal, Erika; Nuñez-Marín, Fidel; Soutullo, Cesar; Alvarez, Enric; Gómez-Ansón, Beatriz; Kelly, Clare; Castellanos, F. Xavier

2012-01-01

Background Default network (DN) abnormalities have been identified in patients with chronic schizophrenia using “resting state” functional magnetic resonance imaging (R-fMRI). Here, we examined the integrity of the DN in patients experiencing their first episode of psychosis (FEP) compared with sex- and age-matched healthy controls. Methods We collected R-fMRI data from 19 FEP patients (mean age 24.9±4.8 yrs, 14 males) and 19 healthy controls (26.1±4.8 yrs, 14 males) at 3 Tesla. Following standard preprocessing, we examined the functional connectivity (FC) of two DN subsystems and the two DN hubs (P<0.0045, corrected). Results Patients with FEP exhibited abnormal FC that appeared largely restricted to the dorsomedial prefrontal cortex (dMPFC) DN subsystem. Relative to controls, FEP patients exhibited weaker positive FC between dMPFC and posterior cingulate cortex (PCC) and precuneus, extending laterally through the parietal lobe to the posterior angular gyrus. Patients with FEP exhibited weaker negative FC between the lateral temporal cortex and the intracalcarine cortex, bilaterally. The PCC and temporo-parietal junction also exhibited weaker negative FC with the right fusiform gyrus extending to the lingual gyrus and lateral occipital cortex, in FEP patients, compared to controls. By contrast, patients with FEP showed stronger negative FC between the temporal pole and medial motor cortex, anterior precuneus and posterior mid-cingulate cortex. Conclusions Abnormalities in the dMPFC DN subsystem in patients with a FEP suggest that FC patterns are altered even in the early stages of psychosis. PMID:22633527

Status of FEP encapsulated solar cell modules used in terrestrial applications

NASA Technical Reports Server (NTRS)

Ratajczak, A. F.; Forestieri, A. F.

1974-01-01

The Lewis Research Center has been engaged in transferring the FEP encapsulated solar cell technology developed for the space program to terrestrial applications. FEP encapsulated solar cell modules and arrays were designed and built expressly for terrestrial applications. Solar cell power systems were installed at three different land sites, while individual modules are undergoing marine environment tests. Four additional power systems are being completed for installation during the summer of 1974. These tests have revealed some minor problems which have been corrected. The results confirm the inherent utility of FEP encapsulated terrestrial solar cell systems.

First-episode psychosis at the West Bologna Community Mental Health Centre: results of an 8-year prospective study.

PubMed

Tarricone, I; Mimmi, S; Paparelli, A; Rossi, E; Mori, E; Panigada, S; Carchia, G; Bandieri, V; Michetti, R; Minenna, G; Boydell, J; Morgan, C; Berardi, D

2012-11-01

Research mostly conducted in the UK and northern Europe has established that there are high rates of first-episode psychosis (FEP) in large cities and immigrant populations; moreover, psychosis has been found to be associated with cannabis use and early trauma. The present study aimed to evaluate the incidence rate of FEP and the distribution of several risk factors (e.g. age, ethnicity, substance abuse) in Bologna, Italy. The Bologna FEP (BoFEP) study is an 8-year prospective study. All FEP patients, 18-64 years old, consecutively referred to the West Bologna Community Mental Health Centre (CMHC) from 2002 to 2009 were evaluated. Sociodemographic information, migration history and clinical data were collected through an ad-hoc schedule. Psychiatric diagnoses were recorded using the Schedule for Clinical Assessment of Neuropsychiatry (SCAN). The overall incidence rate (IR) in the BoFEP study was 16.4 per 100 000 person-years [95% confidence interval (CI) 13.9-18.9]. The incidence was higher in young people, men and migrants (MI). The IR of FEP found by the Bologna study is lower than that found by other European studies. However, as in other studies, the incidence was higher in certain groups. This heterogeneity has implications for policy and mental health service development, and for understanding the aetiology of psychosis.

Integrated Specialized Early-Course Psychosis Treatment Services - University Psychiatric Hospital Vrapce Model.

PubMed

Ostojić, DraŽenka; Čulo, Ilaria; Silić, Ante; Kos, Suzana; Savić, Aleksandar

2018-06-01

First episode of psychosis presents a critical period in terms of numerous associated risks, but also possibilities for effective therapeutic interventions. There is a continued focus on early interventions in prodromal states and early course of frank psychosis, aimed at ensuring faster remission, reducing relapses, achieving better long-term functioning, and preventing adverse outcomes linked to untreated psychosis and chronic psychotic disorders. A number of different specialized treatment models and services exist trying to close knowledge gaps and provide clinical interventions to first-episode psychosis (FEP) patients, but there is still no generally accepted standard of care informing our every-day practice. FEP and early-course psychosis specialized treatment model developed in 2004 in University Psychiatric Hospital Vrapce rests on integration of care across different organization units and clinical presentation acuity levels and patient needs (intensive care, FEP inpatient unit, FEP outpatient services including day hospital). Such integration of FEP services allows for flexible entry point on multiple levels, earlier structuring of therapeutic alliance for those requiring inpatient care, reduction of risks associated with FEP, quicker formation of long-term treatment plans, reduction of delay in accessing specialized services, and a more coordinated diagnostic process and recruitment of FEP patient population. Detailed evaluations of outcomes and comparisons with different treatment models are necessary in order to assess strengths and weaknesses of each specific model and inform modifications to current practice models.

Use of high L.E.T. radiation to improve adhesion of metals to polytetrafluoroethylene

NASA Technical Reports Server (NTRS)

Wheeler, D. R.; Pepper, S. V.

1982-01-01

MgK alpha X-rays (1254 eV) and 2 keV electrons irradiate the surface of polytetrafluoro ethylene (PTFE). The damage is confined to a few tenths of a micron below the surface, and the doses exceed 10 to the eight power rad. X-ray Photoelectron Spectroscopy (XPS) of the irradiated surfaces and mass spectroscopy of the gaseous products of irradiation indicate that the damaged layer is crosslinked or branched PTFE. After either type of irradiation, the surface has enhanced affinity for metals and a lower contact angle with hexadecane. Tape pull tests show that evaporated Ni and Au films adhere better to the irradiated surface. XPS shows the Ni interacts chemically with PTFE forming NiF2 and possibly NiC. However, the gold adhesion and contact angle results indicate that the interaction is, at least in part, chemically nonspecific. Decreased contact angles on FEP Teflon crystallized against gold were attributed to either the presence of a polar oxygen layer or increased physical forces due to greater density. In the case of irradiated PTFE, no oxygen on the surface was observed. The crosslinked structure might, however, have a greater density, thus accounting for the observed increase in adhesion and wettability.

International Test Program for Synergistic Atomic Oxygen and VUV Exposure of Spacecraft Materials

NASA Technical Reports Server (NTRS)

Rutledge, Sharon; Banks, Bruce; Dever, Joyce; Savage, William

2000-01-01

Spacecraft in low Earth orbit (LEO) are subject to degradation in thermal and optical performance of components and materials through interaction with atomic oxygen and vacuum ultraviolet radiation which are predominant in LEO. Due to the importance of LEO durability and performance to manufacturers and users, an international test program for assessing the durability of spacecraft materials and components was initiated. Initial tests consisted of exposure of samples representing a variety of thermal control paints and multilayer insulation materials that have been used in space. Materials donated from various international sources were tested alongside a material whose performance is well known such as Teflon FEP or Kapton H for multilayer insulation, or Z-93-P for white thermal control paints. The optical, thermal or mass loss data generated during the test was then provided to the participating material supplier. Data was not published unless the participant donating the material consented to publication. This paper presents a description of the types of tests and facilities that have been used for the test program as well as some examples of data that have been generated. The test program is intended to give spacecraft builders and users a better understanding of degradation processes and effects to enable improved prediction of spacecraft performance.

Evaluation and Selection of Replacement Thermal Control Materials for the Hubble Space Telescope

NASA Technical Reports Server (NTRS)

Townsend, Jacqueline A.; Hansen, Patricia A.; McClendon, Mark W.; Dever, Joyce A.; Triolo, Jack J.

1998-01-01

The mechanical and optical properties of the metallized Teflon(Registered Trademark) FEP thermal control materials on the Hubble Space Telescope (HST) have degraded over the nearly seven years the telescope has been in orbit. Given the damage to the outer layer of the multi-layer insulation (MLI) that was apparent during the second servicing mission (SM2), the decision was made to replace the outer layer during subsequent servicing missions. A Failure Review Board was established to investigate the damage to the MLI and identify a replacement material. The replacement material had to meet the stringent thermal requirements of the spacecraft and maintain structural integrity for at least ten years. Ten candidate materials were selected and exposed to ten-year HST-equivalent doses of simulated orbital environments. Samples of the candidates were exposed sequentially to low and high energy electrons and protons, atomic oxygen, x-ray radiation, ultraviolet radiation and thermal cycling. Following the exposures, the mechanical integrity and optical properties of the candidates were investigated using Optical Microscopy, Scanning Electron Microscopy (SEM), and a Laboratory Portable Spectroreflectometer (LPSR). Based on the results of these simulations and analyses, the FRB selected a replacement material and two alternates that showed the highest likelihood of providing the requisite thermal properties and surviving for ten years in orbit.q

Differences in cannabis-related experiences between patients with a first episode of psychosis and controls.

PubMed

Bianconi, F; Bonomo, M; Marconi, A; Kolliakou, A; Stilo, S A; Iyegbe, C; Gurillo Muñoz, P; Homayoun, S; Mondelli, V; Luzi, S; Dazzan, P; Prata, D; La Cascia, C; O'Connor, J; David, A; Morgan, C; Murray, R M; Lynskey, M; Di Forti, M

2016-04-01

Many studies have reported that cannabis use increases the risk of a first episode of psychosis (FEP). However, only a few studies have investigated the nature of cannabis-related experiences in FEP patients, and none has examined whether these experiences are similar in FEP and general populations. The aim of this study was to explore differences in self-reported cannabis experiences between FEP and non-psychotic populations. A total of 252 subjects, who met International Classification of Diseases (ICD)-10 criteria for FEP, and 217 controls who reported cannabis use were selected from the Genetics and Psychosis (GAP) study. The Medical Research Council Social Schedule and the Cannabis Experience Questionnaire were used to collect sociodemographic data and cannabis use information, respectively. Both 'bad' and 'enjoyable' experiences were more commonly reported by FEP subjects than controls. Principal components factor analysis identified four components which explained 62.3% of the variance. Linear regression analysis on the whole sample showed that the type of cannabis used and beliefs about the effect of cannabis on health all contributed to determining the intensity and frequency of experiences. Linear regression analysis on FEP subjects showed that the duration of cannabis use and amount of money spent on cannabis were strongly related to the intensity and frequency of enjoyable experiences in this population. These results suggest a higher sensitivity to cannabis effects among people who have suffered their first psychotic episode; this hypersensitivity results in them reporting both more 'bad' and 'enjoyable' experiences. The greater enjoyment experienced may provide an explanation of why FEP patients are more likely to use cannabis and to continue to use it despite experiencing an exacerbation of their psychotic symptoms.

Metacognitive capacity as a predictor of insight in first-episode psychosis.

PubMed

Vohs, Jenifer L; Lysaker, Paul H; Liffick, Emily; Francis, Michael M; Leonhardt, Bethany L; James, Alison; Buck, Kelly D; Hamm, Jay A; Minor, Kyle S; Mehdiyoun, Nikki; Breier, Alan

2015-05-01

Impaired insight is common in the first episode of psychosis (FEP). Although considerable research has examined the factors that are associated with impaired insight in chronic psychosis, less is known about the factors that underlie and sustain poor insight in FEP. Impaired metacognition, or the ability to form integrated representations of self and others, is a promising potential contributor to poor insight in FEP. To explore this possibility, the authors assessed insight and metacognition in 40 individuals with FEP and then examined the relationship between these areas and social cognition domains, neurocognitive domains, and psychotic symptoms. Correlation analyses revealed that improved insight was associated with higher metacognition, better vocabulary and Theory of Mind scores, and fewer symptoms. The domain of metacognitive mastery also predicted clinical insight. Results support the need to develop an integrative therapeutic approach focused on improving metacognition, hence addressing poor insight in FEP.

Examining the usefulness of a Family Empowerment Program guided by the Illness Beliefs Model for families caring for a child with thalassemia.

PubMed

Wacharasin, Chintana; Phaktoop, Maneerat; Sananreangsak, Siriyupa

2015-05-01

The purpose of this pilot study was to design, implement, and evaluate a Family Empowerment Program (FEP), guided by the Illness Beliefs Model. Participants included 25 Thai family members who were the primary caregivers of a child with thalassemia. In Phase I, data were collected from participants using individual in-depth interviews and focus groups before involvement in the FEP. In Phase II, 12 hr of FEP sessions were offered to groups of participants. Content analysis of the audiotaped FEP sessions is reported in this article. Family caregivers reported that the FEP helped them share beliefs and experiences related to caring for their child with thalassemia, make decisions related to families' problems/needs and beliefs, provide each other mutual social support, and develop increased ability to manage care for their chronically ill child through sharing information and learning from other family caregivers about family functioning, family management, and family relationships. Future research is needed to examine the FEP intervention under more controlled conditions with measures that include family functioning and child health outcomes. © The Author(s) 2015.

Characterizing AISI 1045 steel surface duplex-treated by alternating current field enhanced pack aluminizing and nitriding

NASA Astrophysics Data System (ADS)

Xie, Fei; Zhang, Ge; Pan, Jianwei

2018-02-01

Thin cases and long treating time are shortcomings of conventional duplex treatment of aluminizing followed by nitriding (DTAN). Alternating current field (ACF) enhanced DTAN was carried out on AISI 1045 steel by applying an ACF to treated samples and treating agents with a pair of electrodes for overcoming those shortcomings. By investigating cases' structures, phases, composition and hardness distributions of differently treated samples, preliminary studies were made on characterizations of the ACF enhanced duplex treatment to AISI 1045 steel. The results show that, with the help of the ACF, the surface Al-rich phase Al5Fe2 formed in conventional pack aluminizing can be easily avoided and the aluminizing process is dramatically promoted. The aluminizing case can be nitrided either with conventional pack nitriding or ACF enhanced pack nitriding. By applying ACF to pack nitriding, the diffusion of nitrogen into the aluminizing case is promoted. AlN, Fe2∼3N and solid solution of N in iron are efficiently formed as a result of reactions of N with the aluminizing case. A duplex treated case with an effective thickness of more than 170 μm can be obtained by the alternating current field enhanced 4 h pack aluminizing plus 4 h pack nitriding.

ENGINEERED BARRIER SYSTEM: PHYSICAL AND CHEMICAL ENVIRONMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. Jarek

2005-08-29

The purpose of this model report is to describe the evolution of the physical and chemical environmental conditions within the waste emplacement drifts of the repository, including the drip shield and waste package surfaces. The resulting seepage evaporation and gas abstraction models are used in the total system performance assessment for the license application (TSPA-LA) to assess the performance of the engineered barrier system and the waste form. This report develops and documents a set of abstraction-level models that describe the engineered barrier system physical and chemical environment. Where possible, these models use information directly from other reports as input,more » which promotes integration among process models used for TSPA-LA. Specific tasks and activities of modeling the physical and chemical environment are included in ''Technical Work Plan for: Near-Field Environment and Transport In-Drift Geochemistry Model Report Integration'' (BSC 2005 [DIRS 173782], Section 1.2.2). As described in the technical work plan, the development of this report is coordinated with the development of other engineered barrier system reports. To be consistent with other project documents that address features, events, and processes (FEPs), Table 6.14.1 of the current report includes updates to FEP numbers and FEP subjects for two FEPs identified in the technical work plan (TWP) governing this report (BSC 2005 [DIRS 173782]). FEP 2.1.09.06.0A (Reduction-oxidation potential in EBS), as listed in Table 2 of the TWP (BSC 2005 [DIRS 173782]), has been updated in the current report to FEP 2.1.09.06.0B (Reduction-oxidation potential in Drifts; see Table 6.14-1). FEP 2.1.09.07.0A (Reaction kinetics in EBS), as listed in Table 2 of the TWP (BSC 2005 [DIRS 173782]), has been updated in the current report to FEP 2.1.09.07.0B (Reaction kinetics in Drifts; see Table 6.14-1). These deviations from the TWP are justified because they improve integration with FEPs documents. The updates have no impact on the model developed in this report.« less

Irradiation and measurements of fluorinated ethylene-propylene-A on silicon solar cells in vacuum

NASA Technical Reports Server (NTRS)

Marsik, S. J.; Broder, J. D.

1975-01-01

Silicon monoxide (SiO) coated silicon solar cells covered with fluorinated ethylene-propylene-A (FEP-A) were irradiated by 1-MeV electrons in vacuum. The effect of irradiation on the light transmittance of FEP-A was checked by measuring the short-circuit current of the cells while in vacuum after each dose increment, immediately after the irradiation, and again after a minimum elapsed time of 16 hr. The results indicated no apparent loss in transmission due to irradiation of FEP-A and no delamination from the SiO surface while the cells were in vacuum, but embrittlement of FEP-A occurred at the accumulated dose.

Modification of carbon nanotubes with fluorinated ionic liquid for improving processability of fluoro-ethylene-propylene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Hongyang; Chu, Benjamin; Hsiao, Benjamin S.

Fluorinated ionic liquid (F-IL), 1-(3-perfluorooctylpropyl)-3-methylimidazolium bis(perfluoroethylsufonyl)amine, had been successfully prepared and employed to modify multi-wall carbon nanotubes (MWCNTs) for improving the processability of fluoro-ethylene-propylene (FEP). The thermally decomposed temperature of F-IL was higher than 350 °C measured by thermal gravimetric analysis (TGA) which indicated that the fluorinated ionic liquid could be suitable for melting blend with FEP (blending at 290 °C) by a twin-screw extruder. Through “cation-π” interaction between the imidazolium cation of F-IL and the graphene surface of MWCNTs, MWCNTs can be modified with F-IL and used as nanofillers to improve the dispersity of MWCNTs in fluorocopolymer FEP verifiedmore » by SEM images of the FEP nanocomposite. The structural characterization and mechanical property of FEP nanocomposite during the deformation were investigated by tensile experiments and simultaneous time-resolved wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) techniques.« less

Association between serum levels of bioavailable vitamin D and negative symptoms in first-episode psychosis.

PubMed

Yee, Jie Yin; See, Yuen Mei; Abdul Rashid, Nur Amirah; Neelamekam, Sasi; Lee, Jimmy

2016-09-30

Total vitamin D levels had been commonly reported to be lowered in patients with chronic psychotic illnesses in countries from the higher latitudes. However, studies on patients with first episode psychosis (FEP) are limited. In this study we investigated serum concentrations of total and bioavailable vitamin D levels in FEP patients compared to healthy controls and the association between symptom severity and vitamin D components. A total of 31 FEP patients and 31 healthy controls were recruited from Institute of Mental Health, Singapore. FEP patients were identified using Structured Clinical Interview for DSM-IV Axis I disorders (SCID-1) and severity symptoms were assessed using the positive and negative syndrome scale (PANSS). Sera from participants were analyzed for total vitamin D, vitamin D-binding protein (DBP) and bioavailable vitamin D. Linear regressions were performed to examine the associations between serum total and bioavailable vitamin D and the PANSS subscales. Current study noted a significantly lower bioavailable vitamin D was in the FEP group and an association between bioavailable vitamin D and negative symptoms in FEP patients in a population with a consistent supply of sun exposure throughout the year. Copyright © 2016 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

Studies of Ion Beam Charge Neutralization by Ferroelectric Plasma Sources

NASA Astrophysics Data System (ADS)

Stepanov, A.; Gilson, E. P.; Grisham, L.; Davidson, R. C.

2013-10-01

Space-charge forces limit the possible transverse compression of high perveance ion beams that are used in ion-beam-driven high energy density physics applications; the minimum radius to which a beam can be focused is an increasing function of perveance. The limit can be overcome if a plasma is introduced in the beam path between the focusing element and the target in order to neutralize the space charge of the beam. This concept has been implemented on the Neutralized Drift Compression eXperiment (NDCX) at LBNL using Ferroelectric Plasma Sources (FEPS). In our experiment at PPPL, we propagate a perveance-dominated ion beam through a FEPS to study the effect of the neutralizing plasma on the beam envelope and its evolution in time. A 30-60 keV space-charge-dominated Argon beam is focused with an Einzel lens into a FEPS located at the beam waist. The beam is intercepted downstream from the FEPS by a movable Faraday cup that provides time-resolved 2D current density profiles of the beam spot on target. We report results on: (a) dependence of charge neutralization on FEPS plasma density; (b) effects on beam emittance, and (c) time evolution of the beam envelope after the FEPS pulse. Research supported by the U.S. Department of Energy.

Family functioning in first-episode psychosis: a systematic review of the literature.

PubMed

Koutra, Katerina; Vgontzas, Alexandros N; Lionis, Christos; Triliva, Sofia

2014-07-01

The influential role of family in the outcome of chronic schizophrenia is well documented. However, there has been relatively little research on the intrafamilial relationships of people experiencing their first episode of psychosis (FEP), a point in time when most of the changes in family dynamics are observed. The aim of this article is to present a review of the literature focusing on the family environment of FEP patients. We carried out a computerized literature search on MEDLINE and PsycINFO (1990-2013), and a manual search of references of pertinent articles. In total, 27 studies investigating expressed emotion (EE) and family burden (FB) in FEP were identified and fulfilled the inclusion criteria. Similar to chronic patients, a high prevalence of high-EE in carers of FEP patients was reported. High-EE status appears to be independent of the patient's illness-related characteristics, but dependent of relatives' attributions. In contrast to chronic patients, low levels of FB and psychological distress among family members of FEP patients were observed indicating that in the early stages of the illness family involvement is not yet associated with significant disruption in their lives. Studies assessing FB in chronic patients have found a well-established link of FB with patient's illness-related factors, but in FEP patients the families' appraisal of FB is more closely associated with their coping mechanisms. Further studies evaluating family functioning in terms of cohesion and adaptability will shed light on the intrafamilial relationships in FEP patients which may be associated with the long-term outcome of this chronic illness.

The complete genome sequences of poxviruses isolated from a penguin and a pigeon in South Africa and comparison to other sequenced avipoxviruses.

PubMed

Offerman, Kristy; Carulei, Olivia; van der Walt, Anelda Philine; Douglass, Nicola; Williamson, Anna-Lise

2014-06-12

Two novel avipoxviruses from South Africa have been sequenced, one from a Feral Pigeon (Columba livia) (FeP2) and the other from an African penguin (Spheniscus demersus) (PEPV). We present a purpose-designed bioinformatics pipeline for analysis of next generation sequence data of avian poxviruses and compare the different avipoxviruses sequenced to date with specific emphasis on their evolution and gene content. The FeP2 (282 kbp) and PEPV (306 kbp) genomes encode 271 and 284 open reading frames respectively and are more closely related to one another (94.4%) than to either fowlpox virus (FWPV) (85.3% and 84.0% respectively) or Canarypox virus (CNPV) (62.0% and 63.4% respectively). Overall, FeP2, PEPV and FWPV have syntenic gene arrangements; however, major differences exist throughout their genomes. The most striking difference between FeP2 and the FWPV-like avipoxviruses is a large deletion of ~16 kbp from the central region of the genome of FeP2 deleting a cc-chemokine-like gene, two Variola virus B22R orthologues, an N1R/p28-like gene and a V-type Ig domain family gene. FeP2 and PEPV both encode orthologues of vaccinia virus C7L and Interleukin 10. PEPV contains a 77 amino acid long orthologue of Ubiquitin sharing 97% amino acid identity to human ubiquitin. The genome sequences of FeP2 and PEPV have greatly added to the limited repository of genomic information available for the Avipoxvirus genus. In the comparison of FeP2 and PEPV to existing sequences, FWPV and CNPV, we have established insights into African avipoxvirus evolution. Our data supports the independent evolution of these South African avipoxviruses from a common ancestral virus to FWPV and CNPV.

Hierarchical Recursive Organization and the Free Energy Principle: From Biological Self-Organization to the Psychoanalytic Mind

PubMed Central

Connolly, Patrick; van Deventer, Vasi

2017-01-01

The present paper argues that a systems theory epistemology (and particularly the notion of hierarchical recursive organization) provides the critical theoretical context within which the significance of Friston's (2010a) Free Energy Principle (FEP) for both evolution and psychoanalysis is best understood. Within this perspective, the FEP occupies a particular level of the hierarchical organization of the organism, which is the level of biological self-organization. This form of biological self-organization is in turn understood as foundational and pervasive to the higher levels of organization of the human organism that are of interest to both neuroscience as well as psychoanalysis. Consequently, central psychoanalytic claims should be restated, in order to be located in their proper place within a hierarchical recursive organization of the (situated) organism. In light of the FEP the realization of the psychoanalytic mind by the brain should be seen in terms of the evolution of different levels of systematic organization where the concepts of psychoanalysis describe a level of hierarchical recursive organization superordinate to that of biological self-organization and the FEP. The implication of this formulation is that while “psychoanalytic” mental processes are fundamentally subject to the FEP, they nonetheless also add their own principles of process over and above that of the FEP. A model found in Grobbelaar (1989) offers a recursive bottom-up description of the self-organization of the psychoanalytic ego as dependent on the organization of language (and affect), which is itself founded upon the tendency toward autopoiesis (self-making) within the organism, which is in turn described as formally similar to the FEP. Meaningful consilience between Grobbelaar's model and the hierarchical recursive description available in Friston's (2010a) theory is described. The paper concludes that the valuable contribution of the FEP to psychoanalysis underscores the necessity of reengagement with the core concepts of psychoanalytic theory, and the usefulness that a systems theory epistemology—particularly hierarchical recursive description—can have for this goal. PMID:29038652

Hierarchical Recursive Organization and the Free Energy Principle: From Biological Self-Organization to the Psychoanalytic Mind.

PubMed

Connolly, Patrick; van Deventer, Vasi

2017-01-01

The present paper argues that a systems theory epistemology (and particularly the notion of hierarchical recursive organization) provides the critical theoretical context within which the significance of Friston's (2010a) Free Energy Principle (FEP) for both evolution and psychoanalysis is best understood. Within this perspective, the FEP occupies a particular level of the hierarchical organization of the organism, which is the level of biological self-organization. This form of biological self-organization is in turn understood as foundational and pervasive to the higher levels of organization of the human organism that are of interest to both neuroscience as well as psychoanalysis. Consequently, central psychoanalytic claims should be restated, in order to be located in their proper place within a hierarchical recursive organization of the (situated) organism. In light of the FEP the realization of the psychoanalytic mind by the brain should be seen in terms of the evolution of different levels of systematic organization where the concepts of psychoanalysis describe a level of hierarchical recursive organization superordinate to that of biological self-organization and the FEP. The implication of this formulation is that while "psychoanalytic" mental processes are fundamentally subject to the FEP, they nonetheless also add their own principles of process over and above that of the FEP. A model found in Grobbelaar (1989) offers a recursive bottom-up description of the self-organization of the psychoanalytic ego as dependent on the organization of language (and affect), which is itself founded upon the tendency toward autopoiesis (self-making) within the organism, which is in turn described as formally similar to the FEP. Meaningful consilience between Grobbelaar's model and the hierarchical recursive description available in Friston's (2010a) theory is described. The paper concludes that the valuable contribution of the FEP to psychoanalysis underscores the necessity of reengagement with the core concepts of psychoanalytic theory, and the usefulness that a systems theory epistemology-particularly hierarchical recursive description-can have for this goal.

Reflective Packaging

NASA Technical Reports Server (NTRS)

1994-01-01

The aluminized polymer film used in spacecraft as a radiation barrier to protect both astronauts and delicate instruments has led to a number of spinoff applications. Among them are aluminized shipping bags, food cart covers and medical bags. Radiant Technologies purchases component materials and assembles a barrier made of layers of aluminized foil. The packaging reflects outside heat away from the product inside the container. The company is developing new aluminized lines, express mailers, large shipping bags, gel packs and insulated panels for the building industry.

EUPHORE: Research facility to study tropospheric transformation processes

NASA Astrophysics Data System (ADS)

Wirtz, K.

2003-04-01

The EUPHORE simulation chamber consists of two half-spherical Teflon bags, each with a volume of 200 m^3 and a base diameter of 9.2 m. The FEP Teflon has a transmission of about 75% at 280 nm and of more than 80% above 300 nm. Purified and dried ambient air is used to fill the chamber and flush it between experiments. The humidity in the chamber is measured by a dew point hygrometer, and the temperature is monitored by several thermocouples located at different positions inside the chamber. The solar flux is monitored with spectral resolution in the photochemically active spectral region. The simulation chamber is equipped with a number of analytical instruments for the measurement of single VOC components, NO, NO_2, O_3 and other species. In-situ measurements in the ppb range are performed using long-path absorption spectroscopy, in the UV/VIS by DOAS and in the IR by FT-IR. A GC-MS system is used for the sensitive analysis of a variety of reaction products. A newly installed LIF technique allows the in situ measurement of OH and HO_2 radicals during the reaction processes. The technological concept and the organisation structure of the EUPHORE facility will be presented. The integration of quality control measures is an obvious and necessary second step for the successful exploitation of the technically advanced outdoor smog chamber EUPHORE as a research tool. This will underline the leadership of the European scientific community in the important research areas of investigating transformation processes in the troposphere and tracking the influence of human activities on photooxidant formation and its interaction with processes related to global change. In the coming years the main scientific focus will be on testing chemical mechanisms in order to improve the models which describe the atmospheric processes of complex chemical systems. The collaborative work at the EUPHORE outdoor simulation chamber will provide all the users of the installation with a basic platform to exchange analytical technology, sampling procedures, methods of data treatment, and know-how that can also be applied in field campaigns.

A study of the UV and VUV degradation of FEP

NASA Technical Reports Server (NTRS)

George, Graeme A.; Hill, David J. T.; Odonnell, James H.; Pomery, Peter J.; Rasoul, Firas A.

1993-01-01

UV and VUV degradation of fluorinated ethylene propylene (FEP) copolymer was studied using electron spin resonance (ESR) spectroscopy, x-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The ESR study revealed the formation of a terminal polymer radical. The stability of this radical was investigated under different environments. An XPS study of FEP film exposed to VUV and atomic oxygen showed that oxidation takes place on the polymer surface. The study revealed also that the percentage of CF2 in the polymer surface decreased with exposure time and the percentage of CF, CF3, and carbon attached to oxygen increased. SEM micrographs of FEP film exposed to VUV and atomic oxygen identified a rough surface with undulations similar to sand dunes.

Nutritional Deficiencies and Clinical Correlates in First-Episode Psychosis: A Systematic Review and Meta-analysis.

PubMed

Firth, Joseph; Carney, Rebekah; Stubbs, Brendon; Teasdale, Scott B; Vancampfort, Davy; Ward, Philip B; Berk, Michael; Sarris, Jerome

2017-11-30

Diet is increasingly recognized as a potentially modifiable factor influencing the onset and outcomes of psychiatric disorders. Whereas, previous research has shown long-term schizophrenia is associated with various nutritional deficiencies, this meta-analysis aimed to determine the prevalence and extent of nutritional deficits in first-episode psychosis (FEP). A search of electronic databases conducted in July 2017 identified 28 eligible studies, examining blood levels of 6 vitamins and 10 minerals across 2612 individuals: 1221 individuals with FEP and 1391 control subjects. Meta-analyses compared nutrient levels in FEP to nonpsychiatric controls. Clinical correlates of nutritional status in patient samples were systematically reviewed. Significantly lower blood levels of folate (N = 6, n = 827, g = -0.624, 95% confidence interval [CI] = -1.176 to -0.072, P = .027) and vitamin D (N = 7, n = 906, g = -1.055, 95% CI = -1.99 to -0.119, P = .027) were found in FEP compared to healthy controls. Synthesis of clinical correlates found both folate and vitamin D held significant inverse relationships with psychiatric symptoms in FEP. There was also limited evidence for serum level reductions of vitamin C (N = 2, n = 96, g = -2.207, 95% CI = -3.71 to -0.71, P = .004). No differences were found for other vitamins or minerals. Deficits in vitamin D and folate previously observed in long-term schizophrenia appear to exist from illness onset, and are associated with worse symptomology. Further research must examine the direction and nature of these relationships (ie, mediator, moderator, or marker) with clinical status in FEP. Future trials assessing efficacy of nutrient supplementation in FEP samples should consider targeting and stratifying for baseline deficiency. © The Author(s) 2017. Published by Oxford University Press on behalf of the Maryland Psychiatric Research Center.

Verbal memory improvement in first-episode psychosis APOE-ε4 carriers: a pleiotropic effect?

PubMed

Vila-Rodriguez, Fidel; Lang, Donna J; Baitz, Heather; Gicas, Kristina; Thorton, Allen E; Ehmann, Thomas S; Smith, Geoff N; Barr, Alasdair M; Torres, Ivan J; Kopala, Lili C; MacEwan, G William; Müller, Daniel J; Kennedy, James L; Honer, William G

2017-01-01

Verbal memory impairment is a core feature in schizophrenia even at early stages of the disease, but its etiopathogenesis is not fully understood. The APOE -ε4 is the main genetic risk factor for late-onset Alzheimer's disease. Our primary goal was to ascertain whether APOE -ε4 status had a pleiotropic effect in early stages of the illness. A total of 86 first-episode psychosis (FEP) outpatients and 39 healthy volunteers were recruited. Demographic and clinical data, APOE genotyping, and a neuropsychological test battery including the California Verbal Learning Test - second edition (CVLT-II) were administered and assessed at study entry and at 1-year follow-up. Data were analyzed using mixed-model repeated measures, where the dependent variable was verbal memory indexed by California Verbal Learning Test (CVLT) Trials 1-5 total recall score. FEP- APOE -ε4 carriers and FEP- APOE -ε4 noncarriers had similar symptom severity, clinical outcomes, premorbid and current intelligence quotient, and exposure to antipsychotics. There was a main effect of group on CVLT 1-5 (FEP =43.30 vs control =58.25; F [1, 119.7]=42.97; P <0.001) as well as an APOE -ε4 by group by time ( F [4, 116.2]=2.73, P =0.033) interaction with only FEP- APOE -ε4 carriers showing improved verbal memory at follow-up. Our study is the first to report improvement in verbal memory in persons afflicted by FEP who are APOE -ε4 carriers and replicates the prominent verbal memory deficits present in FEP. Our work provides further evidence pointing to an antagonistic pleiotropic effect of APOE -ε4 in neuropsychiatric disorders. Our results merit further research into antagonistic pleiotropic effects in schizophrenia.

Fluoresceination of FepA during colicin B killing: effects of temperature, toxin and TonB.

PubMed

Smallwood, Chuck R; Marco, Amparo Gala; Xiao, Qiaobin; Trinh, Vy; Newton, Salete M C; Klebba, Phillip E

2009-06-01

We studied the reactivity of 35 genetically engineered Cys sulphydryl groups at different locations in Escherichia coli FepA. Modification of surface loop residues by fluorescein maleimide (FM) was strongly temperature-dependent in vivo, whereas reactivity at other sites was much less affected. Control reactions with bovine serum albumin showed that the temperature dependence of loop residue reactivity was unusually high, indicating that conformational changes in multiple loops (L2, L3, L4, L5, L7, L8, L10) transform the receptor to a more accessible form at 37 degrees C. At 0 degrees C colicin B binding impaired or blocked labelling at 8 of 10 surface loop sites, presumably by steric hindrance. Overall, colicin B adsorption decreased the reactivity of more than half of the 35 sites, in both the N- and C- domains of FepA. However, colicin B penetration into the cell at 37 degrees C did not augment the chemical modification of any residues in FepA. The FM modification patterns were similarly unaffected by the tonB locus. FepA was expressed at lower levels in a tonB host strain, but when we accounted for this decrease its FM labelling was comparable whether TonB was present or absent. Thus we did not detect TonB-dependent structural changes in FepA, either alone or when it interacted with colicin B at 37 degrees C. The only changes in chemical modification were reductions from steric hindrance when the bacteriocin bound to the receptor protein. The absence of increases in the reactivity of N-domain residues argues against the idea that the colicin B polypeptide traverses the FepA channel.

Fluoresceination of FepA during Colicin B Killing: Effects of Temperature, Toxin and TonB

PubMed Central

Smallwood, Chuck R.; Marco, Amparo Gala; Xiao, Qiaobin; Trinh, Vy; Newton, Salete M. C.; Klebba, Phillip E.

2009-01-01

We studied the reactivity of 35 genetically engineered Cys sulfhydryl groups at different locations in Escherichia coli FepA. Modification of surface loop residues by fluorescein maleimide (FM) was strongly temperature-dependent in vivo, whereas reactivity at other sites was much less affected. Control reactions with bovine serum albumin showed that the temperature dependence of loop residue reactivity was unusually high, indicating that conformational changes in multiple loops (L2, L3, L4, L5, L7, L8, L10) transform the receptor to a more accessible form at 37 °C. At 0 °C colicin B binding impaired or blocked labeling at 8 of 10 surface loop sites, presumably by steric hindrance. Overall, colicin B adsorption decreased the reactivity of more than half of the 35 sites, in both the N - and C- domains of FepA. However, colicin B penetration into the cell at 37 °C did not augment the chemical modification of any residues in FepA. The FM modification patterns were similarly unaffected by the tonB locus. FepA was expressed at lower levels in a tonB host strain, but when we accounted for this decrease its FM-labeling was comparable whether TonB was present or absent. Thus we did not detect TonB-dependent structural changes in FepA, either alone or when it interacted with colicin B at 37 °C. The only changes in chemical modification were reductions from steric hindrance when the bacteriocin bound to the receptor protein. The absence of increases in the reactivity of N-domain residues argues against the idea (Devanathan and Postle, Mol. Microbiol. 65: 441–453, 2007) that the colicin B polypeptide traverses the FepA channel. PMID:19432807

Family functioning in families of first-episode psychosis patients as compared to chronic mentally ill patients and healthy controls.

PubMed

Koutra, Katerina; Triliva, Sofia; Roumeliotaki, Theano; Stefanakis, Zacharias; Basta, Maria; Lionis, Christos; Vgontzas, Alexandros N

2014-11-30

The present study aimed to investigate possible differences in family environment among patients experiencing their First Episode of Psychosis (FEP), chronic patients and controls. Family cohesion and flexibility (FACES-IV) and psychological distress (GHQ-28) were evaluated in families of 50 FEP and 50 chronic patients, as well as 50 controls, whereas expressed emotion (FQ) and family burden (FBS) were assessed in families of FEP and chronic patients. Multivariable linear regression analysis, adjusted for confounders, indicated impaired cohesion and flexibility for families of FEP patients compared to controls, and lower scores for families of chronic patients compared to those of FEP patients. Caregivers of chronic patients scored significantly higher in criticism, and reported higher burden and psychological distress than those of FEP patients. Our findings suggest that unbalanced levels of cohesion and flexibility, high criticism and burden appeared to be the outcome of psychosis and not risk factors triggering the onset of the illness. Furthermore, emotional over-involvement both in terms of positive (i.e. concern) and negative behaviors (i.e. overprotection) is prevalent in Greek families. Psychoeducational interventions from the early stages of the illness should be considered to promote caregivers' awareness regarding the patients' illness, which in turn, may ameliorate dysfunctional family interactions. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

A Multifunctional ATP-Binding Cassette Transporter System from Vibrio cholerae Transports Vibriobactin and Enterobactin

PubMed Central

Wyckoff, Elizabeth E.; Valle, Ana-Maria; Smith, Stacey L.; Payne, Shelley M.

1999-01-01

Vibrio cholerae uses the catechol siderophore vibriobactin for iron transport under iron-limiting conditions. We have identified genes for vibriobactin transport and mapped them within the vibriobactin biosynthetic gene cluster. Within this genetic region we have identified four genes, viuP, viuD, viuG and viuC, whose protein products have homology to the periplasmic binding protein, the two integral cytoplasmic membrane proteins, and the ATPase component, respectively, of other iron transport systems. The amino-terminal region of ViuP has homology to a lipoprotein signal sequence, and ViuP could be labeled with [3H]palmitic acid. This suggests that ViuP is a membrane lipoprotein. The ViuPDGC system transports both vibriobactin and enterobactin in Escherichia coli. In the same assay, the E. coli enterobactin transport system, FepBDGC, allowed the utilization of enterobactin but not vibriobactin. Although the entire viuPDGC system could complement mutations in fepB, fepD, fepG, or fepC, only viuC was able to independently complement the corresponding fep mutation. This indicates that these proteins usually function as a complex. V. cholerae strains carrying a mutation in viuP or in viuG were constructed by marker exchange. These mutations reduced, but did not completely eliminate, vibriobactin utilization. This suggests that V. cholerae contains genes in addition to viuPDGC that function in the transport of catechol siderophores. PMID:10601218

Migration and transformation of different phosphorus forms in rainfall runoff in bioretention system.

PubMed

Song, Yujia; Song, Shoufa

2018-06-04

Artificial bioretention system consisting of Ophiopogon japonicus infiltration medium was used to simulate an infiltration experiment of rainfall runoff. Continuous extraction method was used to detect contents of inorganic phosphorus (P) under exchangeable state (Ex-P) and aluminium phosphate (Al-P) and iron phosphate (Fe-P) at different depths (0, 5, 15 and 35 cm) of soil infiltration medium in bioretention system. Effluent total P (TP) concentration of the system was also monitored. Results indicated that the adsorption of inorganic P, Al-P and Fe-P by soil infiltration medium was implemented layer by layer from top to bottom and gradually weakened. Moreover, Ex-P was gradually transformed into Al-P and Fe-P, whereas Al-P was gradually transformed into Fe-P; thus, Ex-P content reduced layer by layer, whereas Al-P and Fe-P gradually accumulated. The TP removal rate in runoff rainwater by the system was more than 90%, where the TP that was not used by plants was under dynamic equilibrium in water-soil-root system/biological system.

The Solution Structure, Binding Properties, and Dynamics of the Bacterial Siderophore-binding Protein FepB*

PubMed Central

Chu, Byron C. H.; Otten, Renee; Krewulak, Karla D.; Mulder, Frans A. A.; Vogel, Hans J.

2014-01-01

The periplasmic binding protein (PBP) FepB plays a key role in transporting the catecholate siderophore ferric enterobactin from the outer to the inner membrane in Gram-negative bacteria. The solution structures of the 34-kDa apo- and holo-FepB from Escherichia coli, solved by NMR, represent the first solution structures determined for the type III class of PBPs. Unlike type I and II PBPs, which undergo large “Venus flytrap” conformational changes upon ligand binding, both forms of FepB maintain similar overall folds; however, binding of the ligand is accompanied by significant loop movements. Reverse methyl cross-saturation experiments corroborated chemical shift perturbation results and uniquely defined the binding pocket for gallium enterobactin (GaEnt). NMR relaxation experiments indicated that a flexible loop (residues 225–250) adopted a more rigid and extended conformation upon ligand binding, which positioned residues for optimal interactions with the ligand and the cytoplasmic membrane ABC transporter (FepCD), respectively. In conclusion, this work highlights the pivotal role that structural dynamics plays in ligand binding and transporter interactions in type III PBPs. PMID:25173704

40 CFR 721.10423 - Complex strontium aluminate, rare earth doped (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... earth doped (generic). 721.10423 Section 721.10423 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.10423 Complex strontium aluminate, rare earth doped... substances identified generically as complex strontium aluminate, rare earth doped (PMNs P-12-22, P-12-23, P...

Occupational stress and strain in relation to personal protective equipment of Japanese firefighters assessed by a questionnaire.

PubMed

Son, Su-Young; Lee, Joo-Young; Tochihara, Yutaka

2013-01-01

The purpose of the present study was to elucidate differences in actual work environments, mobility and satisfaction between firefighters wearing aluminized and non-aluminized personal protective equipment (PPE), and to suggest a proper standard test method for Japanese firefighters' PPE. A survey from two cities in Japan (City A: aluminized PPE; City B: non aluminized PPE) was undertaken. A total of 525 firefighters from City A and 757 from City B participated. Firefighters spent 22.5 min (City A) and 27.3 min (City B) on average firefighting with the full set of PPE in one incident, but the heat strain experienced among firefighters from City A was twice that of firefighters from City B (57.5% and 28.4%). Firefighters spent 65.9 min on one incident and 24.2 min for suppression of fire with the full set of PPE on average. The toughest task that caused physical strain in City A was 'stair climbing' and in City B was 'drawing up a hose filled with water'. The most restricted body region due to PPE was the knee for both groups. Evaluations revealed that the aluminized fire jacket had worse ventilation and mobility than the non-aluminized, while the non-aluminized one received with more unfavorable evaluations for water resistance and maintainability.

Utilization of FEP energetics

NASA Technical Reports Server (NTRS)

Frederking, T. H. K.; Abbassi, P.; Afifi, F.; Khandhar, P. K.; Ono, D. Y.; Chen, W. E. W.

1987-01-01

The research and development work on Fountain Effect Pump Systems (FEP systems) has been of interest in the competition between mechanical pumps for He II and FEP units. The latter do not have moving parts. In the course of the work, the energetics have been addressed using one part of a simple four-changes-of-state cycle. One option is the FEP ideal change of state at constant chemical potential (mu). The other option is the two-state sequence mu-P with a d mu=0 state change followed by an isobar. Questions of pump behavior, of flow rate response to temperature difference at the hot end, and related questions of thermodynamic cycle completion and heat transfer have been addressed. Porous media data obtained elucidate differences between vapor-liquid phase separation (VLPS) and Zero Net Mass Transfer (ZNMF).

Prediction of the explosion effect of aluminized explosives

NASA Astrophysics Data System (ADS)

Zhang, Qi; Xiang, Cong; Liang, HuiMin

2013-05-01

We present an approach to predict the explosion load for aluminized explosives using a numerical calculation. A code to calculate the species of detonation products of high energy ingredients and those of the secondary reaction of aluminum and the detonation products, velocity of detonation, pressure, temperature and JWL parameters of aluminized explosives has been developed in this study. Through numerical calculations carried out with this code, the predicted JWL parameters for aluminized explosives have been compared with those measured by the cylinder test. The predicted JWL parameters with this code agree with those measured by the cylinder test. Furthermore, the load of explosion for the aluminized explosive was calculated using the numerical simulation by using the JWL equation of state. The loads of explosion for the aluminized explosive obtained using the predicted JWL parameters have been compared with those using the measured JWL parameters. Both of them are almost the same. The numerical results using the predicted JWL parameters show that the explosion air shock wave is the strongest when the mass fraction of aluminum powder in the explosive mixtures is 30%. This result agrees with the empirical data.

MISSE PEACE Polymers: An International Space Station Environmental Exposure Experiment Being Conducted

NASA Technical Reports Server (NTRS)

deGroh, Kim K.; Banks, Bruce A.; Hammerstrom, Anne; Youngstrom, Erica; Kaminski, Carolyn; Marx, Laura; Fine, Elizabeth; Gummow, Jonathan D.; Wright, Douglas

2002-01-01

As part of the Materials International Space Station Experiment (MISSE), 41 different polymers are being exposed for approximately 1 1/2 years to the low-Earth-orbit (LEO) environment on the exterior of the International Space Station. MISSE is a materials flight experiment sponsored by the Air Force Research Lab/Materials Lab and NASA, and is the first external experiment on the space station. A similar set of 41 polymers will be flown as part of the Polymer Erosion and Contamination Experiment (PEACE) a shuttle flight experiment that is being developed at the NASA Glenn Research Center collaboratively with the Hathaway Brown School for girls. Therefore, these 41 polymers are collectively called the MISSE PEACE Polymers. The purpose of the MISSE PEACE Polymers experiment is to determine how durable polymers are in the LEO space environment where spacecraft, such as the space station, orbit. Polymers are commonly used as spacecraft materials because of their desirable properties such as good flexibility, low density, and certain electrical properties or optical properties (such as a low solar absorptance and high thermal emittance). Two examples of the use of polymers on the exterior of spacecraft exposed to the space environment include metalized Teflon FEP (fluorinated ethylene propylene, DuPont) thermal control materials on the Hubble Space Telescope, and polyimide Kapton (DuPont) solar array blankets.

Exposure of Polymer Film Thermal Control Materials on the Materials International Space Station Experiment (MISSE)

NASA Technical Reports Server (NTRS)

Dever, Joyce; Miller, Sharon; Messer, Russell; Sechkar, Edward; Tollis, Greg

2002-01-01

Seventy-nine samples of polymer film thermal control (PFTC) materials have been provided by the National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) for exposure to the low Earth orbit environment on the exterior of the International Space Station (ISS) as part of the Materials International Space Station Experiment (MISSE). MISSE is a materials flight experiment sponsored by the Air Force Research Lab/Materials Lab and NASA. This paper will describe background, objectives, and configurations for the GRC PFTC samples for MISSE. These samples include polyimides, fluorinated polyimides, and Teflon fluorinated ethylene propylene (FEP) with and without second-surface metallizing layers and/or surface coatings. Also included are polyphenylene benzobisoxazole (PBO) and a polyarylene ether benzimidazole (TOR-LM). On August 16, 2001, astronauts installed passive experiment carriers (PECs) on the exterior of the ISS in which were located twenty-eight of the GRC PFTC samples for 1-year space exposure. MISSE PECs for 3-year exposure, which will contain fifty-one GRC PFTC samples, will be installed on the ISS at a later date. Once returned from the ISS, MISSE GRC PFTC samples will be examined for changes in optical and mechanical properties and atomic oxygen (AO) erosion. Additional sapphire witness samples located on the AO exposed trays will be examined for deposition of contaminants.

Some results of the oxidation investigation of copper and silver samples flown on LDEF

NASA Technical Reports Server (NTRS)

Derooij, A.

1992-01-01

The Long Duration Exposure Facility (LDEF) Mission provides a unique opportunity to study the long term effects of the space environment on materials. The LDEF has been deployed in orbit on 7 April 1984 by the shuttle Challenger in an almost circular orbit with a mean altitude of 477 km and an inclination of 28.5 degrees. It was retrieved from its decayed orbit of 335 km by the shuttle Columbia on 12 January 1990 after almost 6 years in space. The LDEF is a 12-sided, 4.267 m diameter, and 9.144 m long structure. The experiments, placed on trays, are attached to the twelve sides and the two ends of the spacecraft. The LDEF was passively stabilized with one end of the spacecraft always pointing towards the earth center and one of the sides (row 9) always facing the flight direction. The materials investigated originate from the Ultra-Heavy Cosmic Ray Experiment (UHCRE). The main objective is a detailed study of the charge spectra of ultraheavy cosmic-ray nuclei from zinc to uranium and beyond, using solid-state track detectors. Besides the aluminium alloy used for the experiment, UHCRE comprises several other materials. The results of space exposure for two of them, the copper grounding strips and the thermal covers (FEP Teflon/Ag/Inconel) painted black on the inner side (Chemglaze Z306), are presented.

Ground-Based Testing of Replacement Thermal Control Materials for the Hubble Space Telescope

NASA Technical Reports Server (NTRS)

Townsend, Jacqueline A.; Hansen, Patricia A.; McClendon, Mark W.; deGroh, Kim K.; Banks, Bruce A.; Triolo, Jack J.

1998-01-01

The mechanical and optical properties of the metallized Teflon FEP thermal control materials on the Hubble Space Telescope (HST) have degraded over the nearly seven years the telescope has been in orbit. Given the damage to the outer layer of the multi-layer insulation (MLI) that was apparent during the second servicing mission (SM2), the decision was made to replace the outer layer during subsequent servicing missions. A Failure Review Board was established to investigate the damage to the MLI and identify a replacement material. The replacement material had to meet the stringent thermal requirements of the spacecraft and maintain mechanical integrity for at least ten years. Ten candidate materials were selected and exposed to ten-year HST-equivalent doses of simulated orbital environments. Samples of the candidates were exposed sequentially to low and high energy electrons and protons, atomic oxygen, x-ray radiation, ultraviolet radiation and thermal cycling. Following the exposures, the mechanical integrity and optical properties of the candidates were investigated using Optical Microscopy, Scanning Electron Microscopy (SEM), a Laboratory Portable Spectroreflectometer (LPSR) and a Lambda 9 Spectroreflectometer. Based on the results of these simulations and analyses, the Failure Review Board selected a replacement material and two alternates that showed the highest likelihood of providing the requisite thermal properties and surviving for ten years in orbit.

Simultaneous separation and detection of actinides in acidic solutions using an extractive scintillating resin.

PubMed

Roane, J E; DeVol, T A

2002-11-01

An extractive scintillating resin was evaluated for the simultaneous separation and detection of actinides in acidic solutions. The transuranic extractive scintillating (TRU-ES) resin is composed of an inert macroporous polystyrene core impregnated with organic fluors (diphenyloxazole and 1,4-bis-(4-methyl-5-phenyl-2-oxazolyl)benzene) and an extractant (octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide in tributyl phosphate). The TRU-ES resin was packed into FEP Teflon tubing to produce a flow cell (0.2-mL free column volume), which is placed into a scintillation detection system to obtain pulse height spectra and time series data during loading and elution of actinides onto/from the resin. The alpha-particle absolute detection efficiencies ranged from 77% to 96.5%, depending on the alpha energy and quench. In addition to the on-line analyses, off-line analyses of the effluent can be conducted using conventional detection methods. The TRU-ES resin was applied to the quantification of a mixed radionuclide solution and two actual waste samples. The on-line characterization of the mixed radionuclide solution was within 10% of the reported activities whereas the agreement with the waste samples was not as good due to sorption onto the sample container walls and the oxidation state of plutonium. Agreement between the on-line and off-line analyses was within 35% of one another for both waste samples.

LDEF polymeric materials: A summary of Langley characterization

NASA Technical Reports Server (NTRS)

Young, Philip R.; Slemp, Wayne S.; Whitley, Karen S.; Kalil, Carol R.; Siochi, Emilie J.; Shen, James Y.; Chang, A. C.

1995-01-01

The NASA Long Duration Exposure Facility (LDEF) enabled the exposure of a wide variety of materials to the low earth orbit (LEO) environment. This paper provides a summary of research conducted at the Langley Research Center into the response of selected LDEF polymers to this environment. Materials examined include graphite fiber reinforced epoxy, polysulfone, and additional polyimide matrix composites, films of FEP Teflon, Kapton, several experimental high performance polyimides, and films of more traditional polymers such as poly(vinyl toluene) and polystyrene. Exposure duration was either 10 months or 5.8 years. Flight and control specimens were characterized by a number of analytical techniques including ultraviolet-visible and infrared spectroscopy, thermal analysis, scanning electron and scanning tunneling microscopy, x-ray photoelectron spectroscopy, and, in some instances, selected solution property measurements. Characterized effects were found to be primarily surface phenomena. These effects included atomic oxygen-induced erosion of unprotected surfaces and ultraviolet-induced discoloration and changes in selected molecular level parameters. No gross changes in molecular structure or glass transition temperature were noted. The intent of this characterization is to increase our fundamental knowledge of space environmental effects as an aid in developing new and improved polymers for space application. A secondary objective is to develop benchmarks to enhance our methodology for the ground-based simulation of environmental effects so that polymer performance in space can be more reliably predicted.

Construction and Characterization of an Indoor Smog Chamber for Measuring Chemical and Optical Properties of Biomass Burning Aerosols as a Function of Age

NASA Astrophysics Data System (ADS)

Smith, D. M.; Fiddler, M. N.; Sexton, K.; Bililign, S.; Dowdell, T. M.

2016-12-01

Biomass burning is recognized as one of the largest sources of absorbing aerosols in the atmosphere and significantly influences the radiative properties of the atmosphere. In the atmosphere, aerosols dynamically change in complex ways. The chemical composition and physical properties of particles evolve during their atmospheric lifetime due to condensation, oxidation reactions, etc. Changes in chemical composition due to aging is likely to change the optical properties of these particles as well. We have built a 9.01m3 indoor smog chamber made of FEP Teflon. Wood and other organic samples are burned in a tube furnace with the exhaust going directly into the chamber. The construction, characterization, and calibration of the smog chamber will be presented, along with preliminary measurements of extinction and scattering of biomass burning aerosols measured using a Cavity Ring-down and Integrating Nephelometry system. This system allows us to measure any changes in the optical properties of the soot as it ages. Injections to the chamber can be controlled to simulate various atmospheric conditions. These include clean (dry) air, laboratory (room) air, water vapor, NOX, and various biogenic and anthropogenic VOCs such as aromatic hydrocarbons. These components and some of their oxidation products can also be monitored and characterized during aging. The authors acknowledge the support from the National Science Foundation through Grant Number NSF-AGS-1555479

Method of preparing electrolyte for use in fuel cells

DOEpatents

Kinoshita, Kimio; Ackerman, John P.

1978-01-01

An electrolyte compact for fuel cells includes a particulate support material of lithium aluminate that contains a mixture of alkali metal compounds, such as carbonates or hydroxides, as the active electrolyte material. The porous lithium aluminate support structure is formed by mixing alumina particles with a solution of lithium hydroxide and another alkali metal hydroxide, evaporating the solvent from the solution and heating to a temperature sufficient to react the lithium hydroxide with alumina to form lithium aluminate. Carbonates are formed by reacting the alkali metal hydroxides with carbon dioxide gas in an exothermic reaction which may proceed simultaneously with the formation with the lithium aluminate. The mixture of lithium aluminate and alkali metal in an electrolyte active material is pressed or otherwise processed to form the electrolyte structure for assembly into a fuel cell.

Reducing friction and miscibility studies of FEP dispersion/ PDMS fluid blends

NASA Astrophysics Data System (ADS)

Buapool, S.; Thavarungkul, N.; Srisukhumbowornchai, N.

2017-04-01

To develop new polymer blends having reduced friction force of fluorinated ethylene propylene (FEP) dispersion and improved adhesion of polydimethylsiloxane (PDMS) fluid, FEP dispersion was blended with PDMS fluids at different viscosities of 20 cSt and 100 cSt by using solution mixing method. The FEP/PDMS blends were coated on short hollow tubes and examined by penetrating the tubes into the rubber stoppers. It was found that the tubes coated with the blends showed reduced penetration and friction forces and improved adhesion. The tubes coated with the 100 cSt-PDMS blend in the ratio of 5:1.5 demonstrated the penetration and average friction forces as low as 3828 mN and 1524 mN, respectively. The formation of physical blends was characterized and confirmed by FTIR and DSC analyses.

The role of premorbid personality and social cognition in suicidal behaviour in first-episode psychosis: A one-year follow-up study.

PubMed

Canal-Rivero, Manuel; Lopez-Moriñigo, J D; Barrigón, M L; Perona-Garcelán, S; Jimenez-Casado, C; David, A S; Obiols-Llandrich, J E; Ruiz-Veguilla, M

2017-10-01

High suicide attempt (SA) rates have been reported in first-episode psychosis (FEP) patients, particularly during the first year after the illness onset. Despite previous studies establishing several risk factors for suicidal behaviour in FEP, premorbid personality and social cognition have not been sufficiently investigated to date. To test whether personality traits and social cognition are associated with SAs in FEP over a 12-month follow-up. Sixty-five FEP patients were evaluated at first contact with mental health services. The presence of SAs was recorded at six and twelve months after first presentation. Bivariate and multivariate analyses explored the influence of a range of sociodemographic and clinical variables, including premorbid personality and social cognition-related Theory of Mind (ToM) measures, on SAs. SAs were associated with greater severity of symptoms at first hospitalization with psychotic symptoms (OR = 2.18, 95% CI = 1.25-3.82), schizoid personality traits (OR = 1.62, 95% CI = 1.02-2.57) and impairment in a first-order false belief task (OR = 4.26, 95% CI = 1.05-17.31) in the multivariate models. Symptom severity at illness onset, premorbid schizoid personality traits and ToM impairment emerged as predictors of SA in this FEP sample, which, if replicated, may be useful in identifying high-risk groups and implementing more targeted suicide prevention programs in FEP. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

Cannabis Use Is Associated With Increased Psychotic Symptoms and Poorer Psychosocial Functioning in First-Episode Psychosis: A Report From the UK National EDEN Study.

PubMed

Seddon, Jennifer L; Birchwood, Max; Copello, Alex; Everard, Linda; Jones, Peter B; Fowler, David; Amos, Tim; Freemantle, Nick; Sharma, Vimal; Marshall, Max; Singh, Swaran P

2016-05-01

The use of cannabis during the early stage of psychosis has been linked with increased psychotic symptoms. This study aimed to examine the use of cannabis in the 12 months following a first-episode of psychosis (FEP) and the link with symptomatic course and outcome over 1 year post psychosis onset. One thousand twenty-seven FEP patients were recruited upon inception to specialized early intervention services (EIS) for psychosis in the United Kingdom. Participants completed assessments at baseline, 6 and 12 months. The results indicate that the use of cannabis was significantly associated with increased severity of psychotic symptoms, mania, depression and poorer psychosocial functioning. Continued use of cannabis following the FEP was associated with poorer outcome at 1 year for Positive and Negative Syndrome Scale total score, negative psychotic symptoms, depression and psychosocial functioning, an effect not explained by age, gender, duration of untreated psychosis, age of psychosis onset, ethnicity or other substance use. This is the largest cohort study of FEP patients receiving care within EIS. Cannabis use, particularly "continued use," was associated with poorer symptomatic and functional outcome during the FEP. The results highlight the need for effective and early intervention for cannabis use in FEP. © The Author 2015. Published by Oxford University Press on behalf of the Maryland Psychiatric Research Center. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Teflon Might Be a Factor Accounting for a Failed Microvascular Decompression in Hemifacial Spasm: A Technical Note.

PubMed

Dou, Ning-Ning; Zhong, Jun; Liu, Ming-Xing; Xia, Lei; Sun, Hui; Li, Bin; Li, Shi-Ting

2016-01-01

Although Teflon is widely adopted for microvascular decompression (MVD) surgery, it has never been addressed for failure analysis. This study analyzed the reasons for failed MVDs with emphasis on the Teflon sponge. Among the 685 hemifacial spasm cases between 2010 and 2014, 31 were reoperated on within a week because of unsatisfactory outcome, which was focused on in this study. Intraoperative findings regarding Teflon inserts of these repeat MVDs were reviewed. Among the 38 without satisfactory outcomes, 31 underwent repeat MVDs, and they were all spasm free afterwards. Eventually, the final cure rate was 99.2%. It was found in the repeat MVDs that the failure was attributable to the Teflon insert in most of the cases (74.2%) directly or indirectly. It was caused by improper placement (47.8%), inappropriate size (34.8%) and unsuitable shape (17.4%) of the Teflon sponge. Although it is not difficult for an experienced neurosurgeon to discover a neurovascular conflict during the MVD process, the size, shape and location of the Teflon sponge should not be ignored. Basically, the Teflon insert is used to keep the offending artery away from the facial nerve root rather than to isolate it. Therefore, the ideal Teflon sponge should be just small enough to produce a neurovascular separation. © 2016 S. Karger AG, Basel.

Cortical thickness and surface area correlates with cognitive dysfunction among first-episode psychosis patients.

PubMed

Haring, L; Müürsepp, A; Mõttus, R; Ilves, P; Koch, K; Uppin, K; Tarnovskaja, J; Maron, E; Zharkovsky, A; Vasar, E; Vasar, V

2016-07-01

In studies using magnetic resonance imaging (MRI), some have reported specific brain structure-function relationships among first-episode psychosis (FEP) patients, but findings are inconsistent. We aimed to localize the brain regions where cortical thickness (CTh) and surface area (cortical area; CA) relate to neurocognition, by performing an MRI on participants and measuring their neurocognitive performance using the Cambridge Neuropsychological Test Automated Battery (CANTAB), in order to investigate any significant differences between FEP patients and control subjects (CS). Exploration of potential correlations between specific cognitive functions and brain structure was performed using CANTAB computer-based neurocognitive testing and a vertex-by-vertex whole-brain MRI analysis of 63 FEP patients and 30 CS. Significant correlations were found between cortical parameters in the frontal, temporal, cingular and occipital brain regions and performance in set-shifting, working memory manipulation, strategy usage and sustained attention tests. These correlations were significantly dissimilar between FEP patients and CS. Significant correlations between CTh and CA with neurocognitive performance were localized in brain areas known to be involved in cognition. The results also suggested a disrupted structure-function relationship in FEP patients compared with CS.

A study of cytocompatibility and degradation of iron-based biodegradable materials.

PubMed

Oriňaková, Renáta; Oriňak, Andrej; Giretová, Mária; Medvecký, L'ubomír; Kupková, Miriam; Hrubovčáková, Monika; Maskal'ová, Iveta; Macko, Ján; Kal'avský, František

2016-02-01

Biodegradable metallic implants are of significant importance in the replacement of bones or the repair of bone defects. Iron-phosphate-coated carbonyl iron powder (Fe/P) was prepared by the phosphating method. Moreover, Fe/P-Mn alloy was produced by sintering the Fe/P powder mixed with manganese powder. Bare carbonyl iron samples and the Fe/P and Fe/P-Mn sintered samples were evaluated for their microstructure, cytotoxicity, and hemocompatibility. The microstructure of the sintered samples was examined using an optical microscope and scanning electron microscopic analysis. Corrosion behavior was evaluated by potentiodynamic polarization in Hank's solution. The in vitro biocompatibilities were investigated by cytotoxicity and hemolysis tests. The results obtained demonstrate that the addition of Mn resulted in higher surface inhomogeneity, porosity and roughness as well as in increased cytotoxicity. The phosphate coating has a moderately negative effect on the cytotoxicity. The corrosion rates determined from Tafel diagrams were ordered in the following sequence: Fe/P-Mn, Fe, Fe/P from high to low. The hemocompatibility of experimental samples was ordered in the following sequence: Fe/P, Fe/P-Mn, Fe from high to low. All samples were found to be hemocompatible. © The Author(s) 2015.

Possibilities of using aluminate cements in high-rise construction

NASA Astrophysics Data System (ADS)

Kaddo, Maria

2018-03-01

The article describes preferable ways of usage of alternative binders for high-rise construction based on aluminate cements. Possible areas of rational use of aluminate cements with the purpose of increasing the service life of materials and the adequacy of the durability of materials with the required durability of the building are analyzed. The results of the structure, shrinkage and physical and mechanical properties of concrete obtained from dry mixes on the base of aluminate cements for self-leveling floors are presented. To study the shrinkage mechanism of curing binders and to evaluate the role of evaporation of water in the development of shrinkage was undertaken experiment with simple unfilled systems: gypsum binder, portland cement and «corrosion resistant high alumina cement + gypsum». Principle possibility of binder with compensated shrinkage based on aluminate cement, gypsum and modern superplasticizers was defined, as well as cracking resistance and corrosion resistance provide durability of the composition.

Collaborating to improve the use of free-energy and other quantitative methods in drug discovery

NASA Astrophysics Data System (ADS)

Sherborne, Bradley; Shanmugasundaram, Veerabahu; Cheng, Alan C.; Christ, Clara D.; DesJarlais, Renee L.; Duca, Jose S.; Lewis, Richard A.; Loughney, Deborah A.; Manas, Eric S.; McGaughey, Georgia B.; Peishoff, Catherine E.; van Vlijmen, Herman

2016-12-01

In May and August, 2016, several pharmaceutical companies convened to discuss and compare experiences with Free Energy Perturbation (FEP). This unusual synchronization of interest was prompted by Schrödinger's FEP+ implementation and offered the opportunity to share fresh studies with FEP and enable broader discussions on the topic. This article summarizes key conclusions of the meetings, including a path forward of actions for this group to aid the accelerated evaluation, application and development of free energy and related quantitative, structure-based design methods.

T245. THE ROLE OF PROTECTIVE FACTORS IN THE FIRST-EPISODE PSYCHOSIS: PRELIMINARY RESULTS

PubMed Central

Vila-Badia, Regina; Butjosa, Anna; Del Cacho, Núria; de Aguileta, Itziar Riera-López; Alvárez, Mar; Pardo, Marta; Coromina, Marta; Grases, Núria; Ochoa, Susana; Usall, Judith

2018-01-01

Abstract Background Currently, there is a great interest in stress since many diseases can be affected by stress, including psychotic disorders. Interpretation and capacity of the person to tackle situations of psychosocial stress and their recovery capacities are relevant factors in the prevention of psychotic disorders (López-Soler, 2008; N Pereda, 2009, 2010; Noemí Pereda, Guilera, Forns, & Gómez-Benito, 2009). Some of protector factors that have been studied are the following: Resilience (R), Coping Strategies (CS) and Social Support (SS). Furthermore, few studies have been performed with FEP population. Methods This research was part of a longitudinal observational study called ‘PROFEP Group’ in Catalonia. The patients belong to Mental Health Parc Sanitari Sant Joan de Déu (for adults) and Hospital Sant Joan de Déu (for children and adolescents) health care sector. Participants were FEP patients (N=15); males= 9, females= 6) and HC (N=19; males=6, females=13) between 14 and 42 years. We used the PANSS scale (positive, negative and general) to evaluate psychotic symptoms and DUKE (social support), EMA (coping strategies) and CD-RISC-17 (resilience) scales to evaluate protective factors. Results FEP patients showed worse resilience (p<0.05), less social support (p<0.05) and more avoidance coping strategies (p<0.05) than HC. On the other hand, in FEP patients, some protective factors correlate with the symptomatology. The DUKE scale and the EMA cautious action subscale correlate with the total PANSS, while the EMA social joining subscale correlates with the positive symptoms (p<0.05). Discussion Resilience, Coping Strategies and Social Support seem to have an important role in the appearance and severity of an FEP. It is necessary to carry out more studies with more sample, even so, the results indicate that these factors may be important for the prevention of an FEP and could be worked on in future interventions in FEP patients as well as in HC.

Re-examining the prospects of aluminous cements based on alkali-earth and rare-earth oxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chatterjee, A.K., E-mail: anjan.k.chatterjee@gmail.co

2009-11-15

In the family of aluminous cements the potential of strontium aluminate, the strontium-barium aluminate and the barium aluminate cements have been sporadically and incoherently studied over several decades in various parts of the world and more particularly in the East European countries without much wide-spread commercial success. Attempts had also been made to extend the exploratory studies to the (Ca, Sr, Ba)O-Al{sub 2}O{sub 3}-ZrO{sub 2}-HfO{sub 2} system to synthesize super-refractory binders. In fact, the above compositions, prima facie, seem to have the potential of arriving at cementitious formulations that, apart from being super-refractory, may as well be highly resistant tomore » seawater, X-rays and gamma radiation. Looking at these potentials, quite a few experimental studies have been carried out under the guidance and supervision of the present author. The present paper is an endeavour to collate the data on some of these systems both from the published literature as well as from the author's findings. The prime motive has been to review and re-assess the prospects of manufacturing a range of new aluminous binders with superior properties.« less

Ultraviolet irradiation at elevated temperatures and thermal cycling in vacuum of FEP-A covered silicon solar cells

NASA Technical Reports Server (NTRS)

Broder, J. D.; Marsik, S. J.

1978-01-01

Experiments were designed and performed on silicon solar cells covered with heat-bonded FEP-A in an effort to explain the rapid degeneration of open-circuit voltage and maximum power observered on cells of this type included in an experiment on the ATS-6 spacecraft. Solar cells were exposed to ultraviolet light in vacuum at temperatures ranging from 30 to 105 C. The samples were then subjected to thermal cycling from 130 to -130 C. Inspection following irradiation indicated that all the covers remained physically intact. However, during the temperature cycling heat-bonded covers showed cracking. The test showed that heat-bonded FEP-A covers embrittle during UV exposure and the embrittlement is dependent upon sample temperature during irradiation. The results of the experiment suggest a probable mechanism for the degradation of the FEP-A cells on ATS-6.

Impact of welan gum on tricalcium aluminate-gypsum hydration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma Lei, E-mail: malei198713@163.com; Zhao Qinglin, E-mail: zhaoqinglin@whut.edu.cn; Yao Chukang

The retarding effect of welan gum on tricalcium aluminate-gypsum hydration, as a partial system of ordinary Portland cement (OPC) hydration, was investigated with several methods. The tricalcium aluminate-gypsum hydration behavior in the presence or absence of welan gum was researched by field emission gun scanning electron microscopy, X-ray diffraction and zeta potential analysis. Meanwhile, we studied the surface electrochemical properties and adsorption characteristics of welan gum by utilizing a zeta potential analyzer and UV-VIS absorption spectrophotometer. By adding welan gum, the morphology change of ettringite and retardation of hydration stages in tricalcium aluminate-gypsum system was observed. Moreover, we detected themore » adsorption behavior and zeta potential inversion of tricalcium aluminate and ettringite, as well as a rapid decrease in the zeta potential of tricalcium aluminate-gypsum system. The reduction on nucleation rate of ettringite and hydration activity of C{sub 3}A was also demonstrated. Thus, through the adsorption effect, welan gum induces a retarding behavior in tricalcium aluminate-gypsum hydration. Highlights: Black-Right-Pointing-Pointer Adsorption characteristics of welan gum on C{sub 3}A and ettringite have been studied. Black-Right-Pointing-Pointer C{sub 3}A-gypsum hydration behavior and the hydration products are examined in L/S = 3. Black-Right-Pointing-Pointer Welan gum retards the process of C{sub 3}A-gypsum hydration. Black-Right-Pointing-Pointer The addition of welan gum changes the nucleation growth of ettringite.« less

Living history in current orthopaedic hip surgery: intrapelvic teflon granuloma after total hip replacement.

PubMed

Gheorghiu, Daniel; Peter, Viju; Lynch, Martin

2010-02-01

The teflon hip arthroplasty design was used by Sir John Charnley in the early 60's but was taken off the market due to high complication rates. A case is reported of an intrapelvic granuloma after total hip arthroplasty following the use of a teflon socket. This appears to be the last surviving patient treated by Sir John Charnley using a Teflon hip socket design.

Dysfunctional insular connectivity during reward prediction in patients with first-episode psychosis

PubMed Central

Schmidt, André; Palaniyappan, Lena; Smieskova, Renata; Simon, Andor; Riecher-Rössler, Anita; Lang, Undine E.; Fusar-Poli, Paolo; McGuire, Philip; Borgwardt, Stefan J.

2016-01-01

Background Increasing evidence indicates that psychosis is associated with abnormal reward processing. Imaging studies in patients with first-episode psychosis (FEP) have revealed reduced activity in diverse brain regions, including the ventral striatum, insula and anterior cingulate cortex (ACC), during reward prediction. However, whether these reductions in local brain activity are due to altered connectivity has rarely been explored. Methods We applied dynamic causal modelling and Bayesian model selection to fMRI data during the Salience Attribution Task to investigate whether patients with FEP showed abnormal modulation of connectivity between the ventral striatum, insula and ACC induced by rewarding cues and whether these changes were related to positive psychotic symptoms and atypical antipsychotic medication. Results The model including reward-induced modulation of insula–ACC connectivity was the best fitting model in each group. Compared with healthy controls (n = 19), patients with FEP (n = 29) revealed reduced right insula–ACC connectivity. After subdividing patients according to current antipsychotic medication, we found that the reduced insula–ACC connectivity relative to healthy controls was observed only in untreated patients (n = 17), not in patients treated with antipsychotics (n = 12), and that it correlated negatively with unusual thought content in untreated patients with FEP. Limitations The modest sample size of untreated patients with FEP was a limitation of our study. Conclusion This study indicates that insula–ACC connectivity during reward prediction is reduced in untreated patients with FEP and related to the formation of positive psychotic symptoms. Our study further suggests that atypical antipsychotics may reverse connectivity between the insula and the ACC during reward prediction. PMID:26854756

Sharing information about diagnosis and outcome of first-episode psychosis in patients presenting to early intervention services.

PubMed

Farooq, Saeed; Green, Debra J; Singh, Swaran P

2018-05-04

First-episode psychosis (FEP) can be a serious and debilitating disease, but there is limited literature on how to inform patients and carers about its diagnosis and outcome. We aimed to examine the attitudes, practices and views of clinicians working in Early Intervention Service about sharing information on diagnosis and outcome of FEP. A 26-item questionnaire was sent electronically to clinical staff who have been involved in the discussion of FEP diagnosis in Early Intervention Services in the West Midlands, UK. A total of 51 clinicians completed the questionnaire. All respondents stated that patients or carers of those presenting with FEP wish to be informed of their diagnosis, and three-quarters (76%) felt there is a need to develop guidelines on how to inform about diagnosis; 57% stated that they usually use broad diagnostic groups such as psychosis when discussing diagnosis, and only 11% use the term schizophrenia. A total of 40% thought that the therapeutic relationship and treatment adherence (58%) would improve if patients know about their diagnosis; 42 (88%) respondents felt that the likely outcome of the illness should also be discussed with patients when the diagnosis is communicated. The clinicians were aware that service users wished to be informed about the diagnosis and outcome of FEP but had no guidance on the subject. Despite the limitations of an online self-administered survey, the study highlights the need for guidance and improving clinical practice in discussing the diagnosis of FEP in a vulnerable population. © 2018 John Wiley & Sons Australia, Ltd.

Learning to trust: social feedback normalizes trust behavior in first-episode psychosis and clinical high risk.

PubMed

Lemmers-Jansen, Imke L J; Fett, Anne-Kathrin J; Hanssen, Esther; Veltman, Dick J; Krabbendam, Lydia

2018-06-13

Psychosis is characterized by problems in social functioning that exist well before illness onset, and in individuals at clinical high risk (CHR) for psychosis. Trust is an essential element for social interactions that is impaired in psychosis. In the trust game, chronic patients showed reduced baseline trust, impaired response to positive social feedback, and attenuated brain activation in reward and mentalizing areas. We investigated whether first-episode psychosis patients (FEP) and CHR show similar abnormalities in the neural and behavioral mechanisms underlying trust. Twenty-two FEP, 17 CHR, and 43 healthy controls performed two trust games, with a cooperative and an unfair partner in the fMRI scanner. Region of interest analyses were performed on mentalizing and reward processing areas, during the investment and outcome phases of the games. Compared with healthy controls, FEP and CHR showed reduced baseline trust, but like controls, learned to trust in response to cooperative and unfair feedback. Symptom severity was not associated with baseline trust, however in FEP associated with reduced response to feedback. The only group differences in brain activation were that CHR recruited the temporo-parietal junction (TPJ) more than FEP and controls during investment in the unfair condition. This hyper-activation in CHR was associated with greater symptom severity. Reduced baseline trust may be associated with risk for psychotic illness, or generally with poor mental health. Feedback learning is still intact in CHR and FEP, as opposed to chronic patients. CHR however show distinct neural activation patterns of hyper-activation of the TPJ.

DR Argillite Disposal R&D at LBNL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Liange; Kim, Kunhwi; Xu, Hao

2016-08-12

Within the Natural Barrier System (NBS) group of the Used Fuel Disposition (UFD) Campaign at the Department of Energy’s (DOE) Office of Nuclear Energy, LBNL’s research activities have focused on understanding and modeling EDZ evolution and the associated coupled processes and impacts of high temperature on parameters and processes relevant to performance of a clay repository to establish the technical base for the maximum allowable temperature. This report documents results from some of these activities. These activities address key Features, Events, and Processes (FEPs), which have been ranked in importance from medium to high, as listed in Table 7 ofmore » the Used Fuel Disposition Campaign Disposal Research and Development Roadmap (FCR&D-USED-2011-000065 REV0) (Nutt, 2011). Specifically, they address FEP 2.2.01, Excavation Disturbed Zone, for clay/shale, by investigating how coupled processes affect EDZ evolution; FEP 2.2.05, Flow and Transport Pathways; and FEP 2.2.08, Hydrologic Processes, and FEP 2.2.07, Mechanical Processes, and FEP 2.2.09, Chemical Process—Transport, by studying near-field coupled THMC processes in clay/shale repositories. The activities documented in this report also address a number of research topics identified in Research & Development (R&D) Plan for Used Fuel Disposition Campaign (UFDC) Natural System Evaluation and Tool Development (Wang 2011), including Topics S3, Disposal system modeling – Natural System; P1, Development of discrete fracture network (DFN) model; P14, Technical basis for thermal loading limits; and P15 Modeling of disturbed rock zone (DRZ) evolution (clay repository).« less

Social anxiety disorder in first-episode psychosis: incidence, phenomenology and relationship with paranoia.

PubMed

Michail, Maria; Birchwood, Max

2009-09-01

Social anxiety disorder constitutes a significant problem for people with psychosis. It is unclear whether this is a by-product of persecutory thinking. To compare the phenomenology of social anxiety disorder in first-episode psychosis with that in a group without psychosis. The relationship between social anxiety and psychosis symptoms was investigated. A sample of people with first-episode psychosis (FEP group) was compared with a sample with social anxiety disorder without psychosis (SaD group). Of the individuals in the FEP group (n = 80) 25% were diagnosed with an ICD-10 social anxiety disorder (FEP/SaD group); a further 11.6% reported severe difficulties in social encounters. The FEP/SaD and SaD groups reported comparable levels of social anxiety, autonomic symptoms, avoidance and depression. Social anxiety in psychosis was not related to the positive symptoms of the Positive and Negative Syndrome Scale (PANSS) including suspiciousness/persecution. However, a significantly greater percentage of socially anxious v. non-socially anxious individuals with psychosis expressed perceived threat from persecutors, although this did not affect the severity of social anxiety within the FEP/SaD group. The majority of those in the FEP/SaD group did not have concurrent persecutory delusions. Social anxiety is a significant comorbidity in first-episode psychosis. It is not simply an epiphenomenon of psychotic symptoms and clinical paranoia, and it has more than one causal pathway. For a subgroup of socially anxious people with psychosis, anticipated harm is present and the processes that underlie its relationship with social anxiety warrant further investigation.

A Sensitive Technique Using Atomic Force Microscopy to Measure the Low Earth Orbit Atomic Oxygen Erosion of Polymers

NASA Technical Reports Server (NTRS)

deGroh, Kim K.; Banks, Bruce A.; Clark, Gregory W.; Hammerstrom, Anne M.; Youngstrom, Erica E.; Kaminski, Carolyn; Fine, Elizabeth S.; Marx, Laura M.

2001-01-01

Polymers such as polyimide Kapton and Teflon FEP (fluorinated ethylene propylene) are commonly used spacecraft materials due to their desirable properties such as flexibility, low density, and in the case of FEP low solar absorptance and high thermal emittance. Polymers on the exterior of spacecraft in the low Earth orbit (LEO) environment are exposed to energetic atomic oxygen. Atomic oxygen erosion of polymers occurs in LEO and is a threat to spacecraft durability. It is therefore important to understand the atomic oxygen erosion yield (E, the volume loss per incident oxygen atom) of polymers being considered in spacecraft design. Because long-term space exposure data is rare and very costly, short-term exposures such as on the shuttle are often relied upon for atomic oxygen erosion determination. The most common technique for determining E is through mass loss measurements. For limited duration exposure experiments, such as shuttle experiments, the atomic oxygen fluence is often so small that mass loss measurements can not produce acceptable uncertainties. Therefore, a recession measurement technique has been developed using selective protection of polymer samples, combined with postflight atomic force microscopy (AFM) analysis, to obtain accurate erosion yields of polymers exposed to low atomic oxygen fluences. This paper discusses the procedures used for this recession depth technique along with relevant characterization issues. In particular, a polymer is salt-sprayed prior to flight, then the salt is washed off postflight and AFM is used to determine the erosion depth from the protected plateau. A small sample was salt-sprayed for AFM erosion depth analysis and flown as part of the Limited Duration Candidate Exposure (LDCE-4,-5) shuttle flight experiment on STS-51. This sample was used to study issues such as use of contact versus non-contact mode imaging for determining recession depth measurements. Error analyses were conducted and the percent probable error in the erosion yield when obtained by the mass loss and recession depth techniques has been compared. The recession depth technique is planned to be used to determine the erosion yield of 42 different polymers in the shuttle flight experiment PEACE (Polymer Erosion And Contamination Experiment) planned to fly in 2002 or 2003.

Kinetics of pack aluminization of nickel

NASA Technical Reports Server (NTRS)

Seigle, L. L.; Gupta, B. K.; Shankar, R.; Sarkhel, A. K.

1978-01-01

The kinetics of pack aluminization of unalloyed nickel in packs of varying aluminum activity with various halide activators were studied. Surface compositions of the coatings as functions of time, temperature, and pack composition were obtained in order to establish the boundary conditions for diffusion in the system. The structure of the packs was also examined in order to clarify the mechanism of aluminum transport. The results indicate that the kinetics of pack aluminization are controlled jointly by gas diffusion in the pack and solid diffusion in the coating. Levine and Caves' model for gas diffusion was combined with calculations of rates of diffusion in the solid to formulate a more complete theory for the kinetics of pack aluminization.

Neurological soft signs in patients with psychosis and cannabis abuse: a systematic review and meta-analysis of paradox.

PubMed

Ruiz-Veguilla, Miguel; Callado, Luis F; Ferrin, Maite

2012-01-01

Although neurological soft signs (NSSs) have been consistently associated with schizophrenia and a variety of risk factors, few studies have focused on the association between NSSs and environmental factors such as cannabis use, particularly in patients with first episode psychosis (FEP). To review studies that have specifically investigated the association between NSSs and cannabis use in subjects who suffer from psychosis, and more specifically in FEP. A review of studies investigating the associations between neurological function in psychotic patients and cannabis use. A total of 5 studies met our inclusion criteria. Two of these included data only from patients with FEP. Four studies concluded that patients with psychosis and particularly FEP who consumed cannabis showed fewer NSSs. Four possible explanations are suggested for the paradoxical relationship between cannabis use and NSSs in FEP. First, heavy cannabis users present with different acute responses to cannabis use than do occasional cannabis users. Second, the psychoses developed by patients who consume cannabis follow different physio-pathological pathways that include fewer neurodevelopmental abnormalities. Third, the direct effect of cannabis on the Central Nervous System (CNS) may be responsible for the paradox. Finally,severe NSSsare associated with other clinical characteristics that would limit a subject's personal access to cannabis.

Ferroelectric Plasma Sources for Ion Beam Neutralization

NASA Astrophysics Data System (ADS)

Stepanov, A.; Gilson, E. P.; Grisham, L. R.; Davidson, R. C.

2014-10-01

A 40 keV Ar+ beam with a dimensionless perveance of 4 ×10-4 is propagated through a Ferroelectric Plasma Source (FEPS) to determine the effects of charge neutralization on the transverse beam profile. Neutralization is established 5 μs after the FEPS is triggered, and lasts between 10 and 35 μs. When the beam is fully neutralized, the profile has a Gaussian shape with a half-angle divergence of 0.87°, which is attributed to ion optics. The effects of the resistance and capacitance in the pulser circuit on the FEPS discharge are studied. The electron current emitted by the FEPS is calculated from measurements of the forward and return currents in the circuit. Electron emission typically begins 0.5 μs after the driving pulse, lasting for tens of μs, which is similar to the duration of ion beam neutralization. The total emitted charge does not depend significantly on the resistance, but depends strongly on the storage capacitance. Lowering the capacitance from 141 nF to 47 nF results in a near-complete shut-off of charge emission, although the amplitude of the applied voltage pulse is as high as when high-density plasma is produced. Overall, the data suggest that ferroelectric effects are significant in the physics of the FEPS discharge.

Shock Initiation Characteristics of an Aluminized DNAN/RDX Melt-Cast Explosive

NASA Astrophysics Data System (ADS)

Cao, Tong-Tang; Zhou, Lin; Zhang, Xiang-Rong; Zhang, Wei; Miao, Fei-Chao

2017-10-01

Shock sensitivity is one of the key parameters for newly developed, 2,4-dinitroanisole (DNAN)-based, melt-cast explosives. For this paper, a series of shock initiation experiments were conducted using a one-dimensional Lagrangian system with a manganin piezoresistive pressure gauge technique to evaluate the shock sensitivity of an aluminized DNAN/cyclotrimethylenetrinitramine (RDX) melt-cast explosive. This study fully investigated the effects of particle size distributions in both RDX and aluminum, as well as the RDX's crystal quality on the shock sensitivity of the aluminized DNAN/RDX melt-cast explosive. Ultimately, the shock sensitivity of the aluminized DNAN/RDX melt-cast explosives increases when the particle size decreases in both RDX and aluminum. Additionally, shock sensitivity increases when the RDX's crystal quality decreases. In order to simulate these effects, an Ignition and Growth (I&G) reactive flow model was calibrated. This calibrated I&G model was able to predict the shock initiation characteristics of the aluminized DNAN/RDX melt-cast explosive.

Synthesis of magnesium aluminate spinel by periclase and alumina chlorination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orosco, Pablo, E-mail: porosco@unsl.edu.ar; Facultad de Química, Bioquímica y Farmacia, Universidad Nacional de San Luis Chacabuco y Pedernera, San Luis; Barbosa, Lucía

2014-11-15

Highlights: • Use of chlorination for the synthesis of magnesium aluminate spinel. • The reagents used were alumina, periclase and chlorine. • Isothermal and non-isothermal assays were performed in air and Cl{sub 2}–N{sub 2} flows. • The chlorination produced magnesium aluminate spinel at 700 °C. • Selectivity of the chlorination reaction to obtain spinel is very high. - Abstract: A pyrometallurgical route for the synthesis of magnesium aluminate spinel by thermal treatment of a mechanical mixture containing 29 wt% MgO (periclase) and 71 wt% Al{sub 2}O{sub 3} (alumina) in chlorine atmosphere was developed and the results were compared with thosemore » obtained by calcining the same mixture of oxides in air atmosphere. Isothermal and non-isothermal assays were performed in an experimental piece of equipment adapted to work in corrosive atmospheres. Both reagents and products were analyzed by differential thermal analysis (DTA), X-ray diffraction (XRD) and X-ray fluorescence (XRF). Thermal treatment in Cl{sub 2} atmosphere of the MgO–Al{sub 2}O{sub 3} mixture produces magnesium aluminate spinel at 700 °C, while in air, magnesium spinel is generated at 930 °C. The synthesis reaction of magnesium aluminate spinel was complete at 800 °C.« less

Multicale modeling of the detonation of aluminized explosives using SPH-MD-QM method

NASA Astrophysics Data System (ADS)

Peng, Qing; Wang, Guangyu; Liu, Gui-Rong; de, Suvranu

Aluminized explosives have been applied in military industry since decades ago. Compared with ideal explosives, aluminized explosives feature both fast detonation and slow metal combustion chemistry, generating a complex multi-phase reactive flow. Here, we introduce a sequential multiscale model of SPH-MD-QM to simulate the detonation behavior of aluminized explosives. At the bottom level, first-principles quantum mechanics (QM) calculations are employed to obtain the training sets for fitting the ReaxFF potentials, which are used in turn in the reactive molecular dynamics (MD) simulations in the middle level to obtain the chemical reaction rates and equations of states. At the up lever, a smooth particle hydrodynamics (SPH) method incorporated ignition and growth model and afterburning model has been used for the simulation of the detonation and combustion of the aluminized explosive. Simulation is compared with experiment and good agreement is observed. The proposed multiscale method of SPH-MD-QM could be used to optimize the performance of aluminized explosives. The authors would like to acknowledge the generous financial support from the Defense Threat Reduction Agency (DTRA) Grant No. HDTRA1-13-1-0025 and the Office of Naval Research Grants ONR Award No. N00014-08-1-0462 and No. N00014-12-1-0527.

Quantitative analysis for the determination of aluminum percentage and detonation performance of aluminized plastic bonded explosives by laser-induced breakdown spectroscopy

NASA Astrophysics Data System (ADS)

Rezaei, A. H.; Keshavarz, M. H.; Kavosh Tehrani, M.; Darbani, S. M. R.

2018-06-01

The aluminized plastic-bonded explosive (PBX) is a composite material in which solid explosive particles are dispersed in a polymer matrix, which includes three major components, i.e. polymeric binder, metal fuel (aluminum) and nitramine explosive. This work introduces a new method on the basis of the laser-induced breakdown spectroscopy (LIBS) technique in air and argon atmospheres to investigate the determination of aluminum content and detonation performance of aluminized PBXs. Plasma emissions of aluminized PBXs are recorded where atomic lines of Al, C and H as well as molecular bands of AlO and CN are identified. The experimental results demonstrate that a good discrimination and separation between the aluminized PBXs is possible using LIBS and principle component analysis, although they have similar atomic composition. Relative intensity of the AlO/Al is used to determine aluminum percentage of the aluminized PBXs. The obtained quantitative calibration curve using the relative intensity of the AlO/Al is better than the resulting calibration curve using only the intensity of Al. By using the LIBS method and the measured intensity ratio of CN/C, an Al content of 15% is found to be the optimum value in terms of velocity of detonation of the RDX/Al/HTPB standard samples.

Criticism and Depression among the Caregivers of At-Risk Mental State and First-Episode Psychosis Patients

PubMed Central

Hamaie, Yumiko; Ohmuro, Noriyuki; Katsura, Masahiro; Obara, Chika; Kikuchi, Tatsuo; Ito, Fumiaki; Miyakoshi, Tetsuo; Matsuoka, Hiroo; Matsumoto, Kazunori

2016-01-01

Expressed emotion (EE), especially criticism, is an important predictor of outcomes for the patient for a wide range of mental health problems. To understand complex links between EE and various relevant variables in early phase psychosis, this study examined criticism, distress of caregivers, other patients’, and caregivers’ variables, and links between criticism and these variables in those with at-risk mental state (ARMS) for psychosis and first-episode psychosis (FEP). The participants were 56 patients (mean age 18.8 ± 4.2 years) with ARMS and their caregivers (49.4 ± 5.8 years) and 43 patients (21.7 ± 5.2 years) with FEP and their caregivers (49.3 ± 7.4 years). We investigated criticisms made by caregivers using the Japanese version of the Family Attitude Scale and caregiver depressive symptoms via the self-report Beck Depression Inventory. We also assessed psychiatric symptoms and functioning of the patients. Approximately one-third of caregivers of patients with ARMS or FEP had depressive symptoms, predominately with mild-to-moderate symptom levels, whereas only a small portion exhibited high criticism. The level of criticism and depression were comparable between ARMS and FEP caregivers. The link between criticism, caregivers’ depression, and patients’ symptoms were observed in FEP but not in ARMS caregivers. These findings imply that the interaction between criticism and caregivers’ and patients’ mental states may develop during or after the onset of established psychosis and interventions for the caregivers should be tailored to the patient’s specific stage of illness. Interventions for FEP caregivers should target their emotional distress and include education about patient’s general symptoms. PMID:26918629

Does neuroanatomy account for superior temporal dysfunction in early psychosis? A multimodal MRI investigation

PubMed Central

Pettersson-Yeo, William; Benetti, Stefania; Frisciata, Silvia; Catani, Marco; Williams, Steve C.R.; Allen, Paul; McGuire, Philip; Mechelli, Andrea

2015-01-01

Background Neuroimaging studies of ultra-high risk (UHR) and first-episode psychosis (FEP) have revealed widespread alterations in brain structure and function. Recent evidence suggests there is an intrinsic relationship between these 2 types of alterations; however, there is very little research linking these 2 modalities in the early stages of psychosis. Methods To test the hypothesis that functional alteration in UHR and FEP participants would be associated with corresponding structural alteration, we examined brain function and structure in these participants as well as in a group of healthy controls using multimodal MRI. The data were analyzed using statistical parametric mapping. Results We included 24 participants in the FEP group, 18 in the UHR group and 21 in the control group. Patients in the FEP group showed a reduction in functional activation in the left superior temporal gyrus relative to controls, and the UHR group showed intermediate values. The same region showed a corresponding reduction in grey matter volume in the FEP group relative to controls. However, while the difference in grey matter volume remained significant after including functional activation as a covariate of no interest, the reduction in functional activation was no longer evident after including grey matter volume as a covariate of no interest. Limitations Our sample size was relatively small. All participants in the FEP group and 2 in the UHR group had received antipsychotic medication, which may have impacted neurofunction and/or neuroanatomy. Conclusion Our results suggest that superior temporal dysfunction in early psychosis is accounted for by a corresponding alteration in grey matter volume. This finding has important implications for the interpretation of functional alteration in early psychosis. PMID:25338016

The impact of cannabis use on cognitive functioning in patients with schizophrenia: a meta-analysis of existing findings and new data in a first-episode sample.

PubMed

Yücel, Murat; Bora, Emre; Lubman, Dan I; Solowij, Nadia; Brewer, Warrick J; Cotton, Sue M; Conus, Philippe; Takagi, Michael J; Fornito, Alex; Wood, Stephen J; McGorry, Patrick D; Pantelis, Christos

2012-03-01

Cannabis use is highly prevalent among people with schizophrenia, and coupled with impaired cognition, is thought to heighten the risk of illness onset. However, while heavy cannabis use has been associated with cognitive deficits in long-term users, studies among patients with schizophrenia have been contradictory. This article consists of 2 studies. In Study I, a meta-analysis of 10 studies comprising 572 patients with established schizophrenia (with and without comorbid cannabis use) was conducted. Patients with a history of cannabis use were found to have superior neuropsychological functioning. This finding was largely driven by studies that included patients with a lifetime history of cannabis use rather than current or recent use. In Study II, we examined the neuropsychological performance of 85 patients with first-episode psychosis (FEP) and 43 healthy nonusing controls. Relative to controls, FEP patients with a history of cannabis use (FEP + CANN; n = 59) displayed only selective neuropsychological impairments while those without a history (FEP - CANN; n = 26) displayed generalized deficits. When directly compared, FEP + CANN patients performed better on tests of visual memory, working memory, and executive functioning. Patients with early onset cannabis use had less neuropsychological impairment than patients with later onset use. Together, these findings suggest that patients with schizophrenia or FEP with a history of cannabis use have superior neuropsychological functioning compared with nonusing patients. This association between better cognitive performance and cannabis use in schizophrenia may be driven by a subgroup of "neurocognitively less impaired" patients, who only developed psychosis after a relatively early initiation into cannabis use.

Prefrontal and Striatal Gamma-Aminobutyric Acid Levels and the Effect of Antipsychotic Treatment in First-Episode Psychosis Patients.

PubMed

de la Fuente-Sandoval, Camilo; Reyes-Madrigal, Francisco; Mao, Xiangling; León-Ortiz, Pablo; Rodríguez-Mayoral, Oscar; Jung-Cook, Helgi; Solís-Vivanco, Rodolfo; Graff-Guerrero, Ariel; Shungu, Dikoma C

2018-03-15

Abnormally elevated levels of gamma-aminobutyric acid (GABA) in the medial prefrontal cortex (mPFC) have been reported in antipsychotic-free patients with schizophrenia. Whether such GABA elevations are also present in other brain regions and persist after antipsychotic treatment has not been previously investigated. Twenty-eight antipsychotic-naïve patients with first-episode psychosis (FEP) and 18 healthy control subjects completed the study. Following baseline proton magnetic resonance spectroscopy scans targeting the mPFC and a second region, the dorsal caudate, patients with FEP were treated with oral risperidone for 4 weeks at an initial dose of 1 mg/day that was titrated as necessary based on clinical judgment. After the 4-week treatment period, both groups were brought back to undergo outcome magnetic resonance spectroscopy scans, which were identical to the scans conducted at baseline. At baseline, higher GABA levels were found both in the mPFC and in the dorsal caudate of patients with FEP compared with healthy control subjects. Following 4 weeks of antipsychotic treatment, GABA levels in patients with FEP decreased relative to baseline in the mPFC, but decreased only at the trend level relative to baseline in the dorsal caudate. For either brain region, GABA levels at 4 weeks or posttreatment did not differ between patients with FEP and healthy control subjects. The results of the present study documented elevations of GABA levels both in the mPFC and, for the first time, in the dorsal caudate of antipsychotic-naïve patients with FEP, which normalized in both regions following 4 weeks of antipsychotic treatment. Copyright © 2017 Society of Biological Psychiatry. Published by Elsevier Inc. All rights reserved.

Testing a model of the relationship between childhood sexual abuse and psychosis in a first-episode psychosis group: the role of hallucinations and delusions, posttraumatic intrusions, and selective attention.

PubMed

Bendall, Sarah; Hulbert, Carol Anne; Alvarez-Jimenez, Mario; Allott, Kelly; McGorry, Patrick D; Jackson, Henry James

2013-11-01

Several theories suggest that posttraumatic intrusive symptoms are central to the relationship between childhood trauma (CT) and hallucinations and delusions in psychosis. Biased selective attention has been implicated as a cognitive process underlying posttraumatic intrusions. The current study sought to test theories of the relationship between childhood sexual abuse (CSA), hallucinations and delusions, posttraumatic intrusions, and selective attention in first-episode psychosis (FEP). Twenty-eight people with FEP and 21 nonclinical controls were assessed for CT and psychotic and posttraumatic stress symptoms and completed an emotional Stroop test using CSA-related and other words. Those with FEP and CSA had more severe hallucinations and delusions than those with FEP and without CSA. They also reported posttraumatic intrusions at clinical levels and showed selective attention to CSA-related words. The results are consistent with the posttraumatic intrusions account of hallucinations and delusions in those with CSA and psychosis.

Terrestrial applications of FEP-encapsulated solar cell modules. [power systems using Fluorinated Ethylene Propylene encapsulation

NASA Technical Reports Server (NTRS)

Forestieri, A. F.; Ratajczak, A. F.

1974-01-01

The NASA-Lewis Research Center program of transferring the FEP-encapsulated solar cell technology developed for the space program to terrestrial applications is presented. The electrical power system design and the array mechanical design are described, and power systems being tested are discussed. The latter are located at NOAA-RAMOS weather stations at Sterling, Va., and Mammoth Mountain, Calif.; on the roof of the Lewis Research Center; on a NOAA-Coast Guard buoy in the Gulf of Mexico; in a U.S. Forest Service mountaintop voice repeater station in the Inyo National Forest, Calif., and in a backpack charger for portable transmitter/receivers being used in the same place. Preliminary results of testing are still incomplete, but show that rime ice can cause cracks in modular cells without damaging the FEP though, which keeps the grid lines intact, and that electrically active elements of the module must be completely sealed from salt water to prevent FEP delamination.

Understanding access and use of technology among youth with first-episode psychosis to inform the development of technology-enabled therapeutic interventions.

PubMed

Abdel-Baki, Amal; Lal, Shalini; D-Charron, Olivier; Stip, Emmanuel; Kara, Nadjia

2017-02-01

Computers, video games and technological devices are part of young people's everyday lives. However, their use in first-episode psychosis (FEP) treatment is rare. The purpose of this study was to better understand the access and use of technology among individuals with FEP, including gaming activities, to inform future development of technology-enabled therapeutic applications. Self-administered survey on use of technological tools in 71 FEP individuals. PCs/laptops were used by all participants; cellphones/smartphones by 92%, consoles by 83% (mainly male and younger participants). Women texted and used social networks more frequently; men played games (mainly action) more often. The younger individuals reported playing games frequently (32% daily) with less use of the Web and social networks (favourite: Facebook). These data will be useful for developing Web-based psychoeducation tools and cognitive remediation video games for youth with FEP. © 2015 Wiley Publishing Asia Pty Ltd.

The Positive and Negative Experiences of Caregiving for Siblings of Young People with First Episode Psychosis

PubMed Central

Bowman, Siann; Alvarez-Jimenez, Mario; Wade, Darryl; Howie, Linsey; McGorry, Patrick

2017-01-01

Background: The impact of first episode psychosis (FEP) upon parents’ experience of caregiving has been well-documented. However, the determinants and nature of this remain poorly understood in siblings. It is hypothesized that siblings of young people with FEP are also impacted by caregiving and burden. This study aimed to characterize the experience of caregiving for siblings of young people with FEP. Method: Survey methodology was used to explore the experience of 157 siblings in the first 18 months of their brother or sister’s treatment for FEP. Participants reported on their appraisal of the negative and positive aspects of caregiving as measured by the Experience of Caregiving Inventory (ECI). Descriptive statistics were used to establish the results for the total sample as well as for gender and birth order differences. A series of multivariate regression analyses were conducted to determine the relationships between illness characteristics and siblings’ experience of caregiving. Results: Older brothers reported the lowest scores for negative experiences in caregiving and younger sisters reported the highest. Negative experiences in caregiving resulted in less warmth within the sibling relationship and impacted negatively upon quality of life. When the young person with FEP had attempted suicide and/or been physically violent, siblings experienced more caregiver burden. Multivariate analysis showed that female gender was a significant factor in explaining the impact of illness related variables on the experience of caregiving. Conclusion: Suicide attempts and a history of violence resulted in higher caregiving burden for siblings regardless of whether they lived with the young person experiencing FEP or not. Female siblings are at higher risk of negative experiences from caregiving resulting in a reduced quality of life and a changed sibling relationship. Suicide attempts and violence are indicators for intensive case management to improve outcomes for the individual with FEP which may in turn reduce the burden experienced by the sibling. Clinicians can use these findings to identify siblings, assertively intervene and provide increased psychological support, psychoeducation and practical problem solving to reduce the burden. The caregiving role that they already play for their ill brother or sister should be recognized. PMID:28588522

Do stress and support matter for caring? The role of perceived stress and social support on expressed emotion of carers of persons with first episode psychosis.

PubMed

Sadath, Anvar; Muralidhar, D; Varambally, Shivarama; Gangadhar, B N; Jose, Justin P

2017-02-01

Caring for a person with first episode psychosis (FEP) is a challenging and distressing task for the carers. The carers' stress in the early stage of psychosis can increase their expressed emotion (EE) while social support is hypothesized to decrease EE. However, the influence of stress and social support on carers' EE is not well understood in FEP. To examine how the stress and social support shape expressed emotion in the carers of FEP. Seventy one carers of the patients with non-affective FEP were recruited from the inpatient psychiatry ward of a tertiary mental health care center in South India. The family questionnaire, perceived stress scale and multidimensional scale of perceived social support were used to measure their EE, stress and social support respectively. Carers experienced high level of perceived stress, EE and poor social support. Perceived stress significantly increased EE (β=0.834; p<0.001) and social support did not significantly influence EE (β=-0.065; p>0.05). Perceived stress predicted 76 percent of the variance on EE (Adjusted R 2 =0.761). The results emphasize high level of stress and EE in carers of patients with FEP that implies the need for appropriate psychosocial interventions to manage their stress. Copyright © 2016 Elsevier B.V. All rights reserved.

Deficits of cognitive theory of mind and its relationship with functioning in individuals with an at-risk mental state and first-episode psychosis.

PubMed

Ohmuro, Noriyuki; Katsura, Masahiro; Obara, Chika; Kikuchi, Tatsuo; Sakuma, Atsushi; Iizuka, Kunio; Hamaie, Yumiko; Ito, Fumiaki; Matsuoka, Hiroo; Matsumoto, Kazunori

2016-09-30

Disturbance of theory of mind (ToM) and its relationship with functioning in schizophrenia is well documented; however, this is unclear in spectrum disorders like at-risk mental state (ARMS) and first-episode psychosis (FEP). To assess mental state reasoning ability, the total score of the Theory of Mind Picture Stories Task questionnaire was compared among 36 Japanese individuals with ARMS, 40 with FEP, and 25 healthy controls (HC). Pearson's correlations between ToM performance and global and social functioning indices were examined. ToM performance for FEP and ARMS subjects was significantly lower than that for HC, though the significance of the difference between the ARMS and HC disappeared when controlling for premorbid IQ. ToM deficits in ARMS subjects were confirmed only in the comprehension of higher-order false belief. Only among FEP subjects were ToM performance and global functioning significantly correlated, though the significance disappeared when controlling for neurocognitive performance or dose of antipsychotics. No significant correlation between ToM performance and social functioning was observed in the FEP and ARMS groups. The current findings suggest that ToM deficits emerge in ARMS subjects confined within a higher-order domain, and that the relationship between ToM impairment and functional deterioration might be established after psychosis onset. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

On the kinetics of pack aluminization

NASA Technical Reports Server (NTRS)

Gupta, B. K.; Sarkhel, A. K.; Seigle, L. L.

1975-01-01

A theory of pack aluminization has been formulated by combining gaseous and solid-state diffusion rates. This theory relates the surface composition of the coating and therefore, in principle, the phase morphology and the growth rate of the coating, to pack operating parameters such as pack aluminum density, type of activator, temperature and others. Experimental data on the aluminization of unalloyed nickel in pure aluminum packs obtained to date are in good agreement with the predictions of the theory.

Ambient Observations of the Soot Aging Process during the SHARP Intensive Field Campaign

NASA Astrophysics Data System (ADS)

Reed, C.; Collins, D. R.; Khalizov, A. F.; Zheng, J.; Zhang, R.

2009-12-01

Soot aerosols affect climate both directly through absorption of solar radiation and indirectly by potentially serving as cloud condensation nuclei. Among the sources of uncertainty surrounding the effects of soot aerosol on the environment is the lack of scientific insight into the soot aging process, in which soot particles develop a coating of secondary species such as sulfates, ammonium, nitrate, and organics. Such processes may alter the behavior of soot by modifying particle morphology over time leading to changes in chemical, physical and scattering properties of the aerosol. However, it is often difficult to quantify such processes in the ambient environment due to the complex composition and spatial and temporal variability of the atmospheric aerosol. In order to better understand the effects of the environment on soot particles, it is desirable to study the processes responsible for their transformation in the ambient air without influence from variability in source region and history prior to sampling. To achieve this, the overall soot aging process in the ambient environment was physically isolated utilizing environmental chambers. Chamber measurements were conducted on the Moody Tower at the University of Houston using The Ambient Aerosol Chamber for Evolution Studies (AACES) during the SHARP campaign. AACES is a roughly cubical chamber constructed of a rigid acrylic outer shell, which transmits UV radiation both in the UV-B and UV-A ranges. FEP Teflon lines the inside of the chamber on all sides and the top, while expanded-PTFE (ePTFE) Teflon is used on the bottom of the chamber. The fibrous structure of the ePTFE acts as a barrier to particulates, while allowing gas molecules to move virtually unimpeded from the surrounding air into the chamber, creating an environment inside the chamber that is initially free of particles and continuously mimics the local ambient air. In order to study the effects of the soot aging process, a non-premixed propane flame was used to generate a polydisperse fresh soot aerosol. Then, using a differential mobility analyzer, a monodisperse, uncharged soot aerosol was injected into the environmental chamber. Observations of particle concentration, size, hygroscopicity, effective density, and light extinction and scattering properties were carried out over time using a tandem differential mobility analyzer system, an aerosol particle mass analyzer, a nephelometer and a cavity ringdown spectrometer. Results from preliminary analysis of the data collected during the campaign will be presented.

MISSE PEACE Polymers Atomic Oxygen Erosion Results

NASA Technical Reports Server (NTRS)

deGroh, Kim, K.; Banks, Bruce A.; McCarthy, Catherine E.; Rucker, Rochelle N.; Roberts, Lily M.; Berger, Lauren A.

2006-01-01

Forty-one different polymer samples, collectively called the Polymer Erosion and Contamination Experiment (PEACE) Polymers, have been exposed to the low Earth orbit (LEO) environment on the exterior of the International Space Station (ISS) for nearly 4 years as part of Materials International Space Station Experiment 2 (MISSE 2). The objective of the PEACE Polymers experiment was to determine the atomic oxygen erosion yield of a wide variety of polymeric materials after long term exposure to the space environment. The polymers range from those commonly used for spacecraft applications, such as Teflon (DuPont) FEP, to more recently developed polymers, such as high temperature polyimide PMR (polymerization of monomer reactants). Additional polymers were included to explore erosion yield dependence upon chemical composition. The MISSE PEACE Polymers experiment was flown in MISSE Passive Experiment Carrier 2 (PEC 2), tray 1, on the exterior of the ISS Quest Airlock and was exposed to atomic oxygen along with solar and charged particle radiation. MISSE 2 was successfully retrieved during a space walk on July 30, 2005, during Discovery s STS-114 Return to Flight mission. Details on the specific polymers flown, flight sample fabrication, pre-flight and post-flight characterization techniques, and atomic oxygen fluence calculations are discussed along with a summary of the atomic oxygen erosion yield results. The MISSE 2 PEACE Polymers experiment is unique because it has the widest variety of polymers flown in LEO for a long duration and provides extremely valuable erosion yield data for spacecraft design purposes.

[Preparation and clinical application of Teflon-wire piston and stapes height measurer].

PubMed

Xie, Nan-ping

2003-08-01

With Teflon, and a tiny stainless steel needle of a number 7 injector and an acupuncture needle,Teflon-piston and a measurer of the stapes height were prepared respectively of stapedectomy for treatment of otosclerosis. Good clinical results were achieved with these simple and useful devices.

Risk management in a large-scale CO2 geosequestration pilot project, Illinois, USA

USGS Publications Warehouse

Hnottavange-Telleen, K.; Chabora, E.; Finley, R.J.; Greenberg, S.E.; Marsteller, S.

2011-01-01

Like most large-scale infrastructure projects, carbon dioxide (CO 2) geological sequestration (GS) projects have multiple success criteria and multiple stakeholders. In this context "risk evaluation" encompasses multiple scales. Yet a risk management program aims to maximize the chance of project success by assessing, monitoring, minimizing all risks in a consistent framework. The 150,000-km2 Illinois Basin underlies much of the state of Illinois, USA, and parts of adjacent Kentucky and Indiana. Its potential for CO2 storage is first-rate among basins in North America, an impression that has been strengthened by early testing of the injection well of the Midwest Geological Sequestration Consortium's (MGSC's) Phase III large scale demonstration project, the Illinois Basin - Decatur Project (IBDP). The IBDP, funded by the U.S. Department of Energy's National Energy Technology Laboratory (NETL), represents a key trial of GS technologies and project-management techniques. Though risks are specific to each site and project, IBDP risk management methodologies provide valuable experience for future GS projects. IBDP views risk as the potential for negative impact to any of these five values: health and safety, environment, financial, advancing the viability and public acceptability of a GS industry, and research. Research goals include monitoring one million metric tonnes of injected CO2 in the subsurface. Risk management responds to the ways in which any values are at risk: for example, monitoring is designed to reduce uncertainties in parameter values that are important for research and system control, and is also designed to provide public assurance. Identified risks are the primary basis for risk-reduction measures: risks linked to uncertainty in geologic parameters guide further characterization work and guide simulations applied to performance evaluation. Formally, industry defines risk (more precisely risk criticality) as the product L*S, the Likelihood multiplied by the Severity of negative impact. L and S are each evaluated on five-point scales, yielding a theoretical spread in risk values of 1 through 25. So defined, these judgment-based values are categorical and ordinal - they do not represent physically measurable quantities, but are nonetheless useful for comparison and therefore decision support. The "risk entities" first evaluated are FEPs - conceptual Features, Events, and Processes based on the list published by Quintessa Ltd. After concrete scenarios are generated based on selected FEPs, scenarios become the critical entities whose associated risks are evaluated and tracked. In IBDP workshops, L and S values for 123 FEPs were generated through expert elicitation. About 30 experts in the project or in GS in general were assigned among six facilitated working groups, and each group was charged to envision risks within a sphere of project operations. Working groups covered FEPs with strong spatial characteristics - such as those related to the injection wellbore and simulated plume footprint - and "nonspatial" FEPs related to finance, regulations, legal, and stakeholder issues. Within these working groups, experts shared information, examined assumptions, refined and extended the FEP list, calibrated responses, and provided initial L and S values by consensus. Individual rankings were collected in a follow-up process via emailed spreadsheets. For each of L and S, three values were collected: Lower Bound, Best Guess, and Upper Bound. The Lower-Upper Bound ranges and the spreads among experts can be interpreted to yield rough confidence measures. Based on experts' responses, FEPs were ranked in terms of their L*S risk levels. FEP rankings were determined from individual (not consensus or averaged) results, thus no high-risk responses were damped out. The higher-risk FEPs were used to generate one or more concrete, well defined risk-bearing scenarios for each FEP. Any FEP scored by any expert as having associated risk of

Ions beams and ferroelectric plasma sources

NASA Astrophysics Data System (ADS)

Stepanov, Anton

Near-perfect space-charge neutralization is required for the transverse compression of high perveance ion beams for ion-beam-driven warm dense matter experiments, such as the Neutralized Drift Compression eXperiment (NDCX). Neutralization can be accomplished by introducing a plasma in the beam path, which provides free electrons that compensate the positive space charge of the ion beam. In this thesis, charge neutralization of a 40 keV, perveance-dominated Ar+ beam by a Ferroelectric Plasma Source (FEPS) is investigated. First, the parameters of the ion beam, such as divergence due to the extraction optics, charge neutralization fraction, and emittance were measured. The ion beam was propagated through the FEPS plasma, and the effects of charge neutralization were inferred from time-resolved measurements of the transverse beam profile. In addition, the dependence of FEPS plasma parameters on the configuration of the driving pulser circuit was studied to optimize pulser design. An ion accelerator was constructed that produced a 30-50 keV Ar + beam with pulse duration <300 mus and dimensionless perveance Q up to 8 x 10-4. Transverse profile measurements 33 cm downstream of the ion source showed that the dependence of beam radius on Q was consistent with space charge expansion. It was concluded that the beam was perveance-dominated with a charge neutralization fraction of approximately zero in the absence of neutralizing plasma. Since beam expansion occurred primarily due to space charge, the decrease in effective perveance due to neutralization by FEPS plasma can be inferred from the reduction in beam radius. Results on propagation of the ion beam through FEPS plasma demonstrate that after the FEPS is triggered, the beam radius decreases to its neutralized value in about 5 mus. The duration of neutralization was about 10 mus at a charging voltage VFEPS = 5.5 kV and 35 mus at VFEPS = 6.5 kV. With VFEPS = 6.5 kV, the transverse current density profile 33 cm downstream of the source had a Gaussian shape with xrms =5 mm, which corresponds to a half-angle divergence of 0.87°. The measurements show that near-perfect charge neutralization with FEPS can be attained. No loss of ion beam current was detected, indicating the absence of a neutral cloud in the region of beam propagation, which would cause beam loss to charge exchange collisions. This provides evidence in favor of using FEPS in a future Heavy Ion Fusion accelerator. The FEPS discharge was investigated based on current-voltage measurements in the pulser circuit. Different values of series resistance and storage capacitance in the pulser circuit were used. The charged particle current emitted by the FEPS into vacuum was measured from the difference in forward and return currents in the driving circuit. It was found that FEPS is an emitter of negative charge, and that electron current emission begins approximately 0.5 mus after the fast-rising high voltage pulse is applied and lasts for tens of mus. The value of the series resistance in the pulser circuit was varied to change the rise time of the voltage pulse; plasma density was expected to decrease with increasing values of resistance. However, the data showed that changing the resistance had no significant effect. The average charge emitted per shot depends strongly on the value of the storage capacitance. Lowering the capacitance from 141 nF to 47 nF resulted in a near-complete shut-off of charge emission, although the amplitude of the applied voltage pulse was as high, and rise time as short, as when high-density plasma was produced. Increasing the capacitance from 141 nF to 235 nF increased the average charge emitted per shot by a factor of 2.

Quantitative description of yttrium aluminate ceramic composition by means of Er+3 microluminescence spectrum

NASA Astrophysics Data System (ADS)

Videla, F. A.; Tejerina, M. R.; Moreira-Osorio, L.; Conconi, M. S.; Orzi, D. J. O.; Flores, T.; Ponce, L. V.; Bilmes, G. M.; Torchia, G. A.

2018-05-01

The composition of erbium-doped yttrium aluminate ceramics was analyzed by means of confocal luminescence spectroscopy, EDX, and X-ray diffraction. A well-defined linear correlation was found between a proposed estimator computed from the luminescence spectrum and the proportion of ceramic phases coexisting in different samples. This result shows the feasibility of using erbium luminescence spectroscopy to perform a quantitative determination of different phases of yttrium aluminates within a micrometric region in nanograined ceramics.

Phosphate-bonded calcium aluminate cements

DOEpatents

Sugama, Toshifumi

1993-01-01

A method is described for making a rapid-setting phosphate-bonded cementitious material. A powdered aluminous cement is mixed with an aqueous solution of ammonium phosphate. The mixture is allowed to set to form an amorphous cementitious material which also may be hydrothermally treated at a temperature of from about 120.degree. C. to about 300.degree. C. to form a crystal-containing phosphate-bonded material. Also described are the cementitious products of this method and the cement composition which includes aluminous cement and ammonium polyphosphate.

Phosphate-bonded calcium aluminate cements

DOEpatents

Sugama, T.

1993-09-21

A method is described for making a rapid-setting phosphate-bonded cementitious material. A powdered aluminous cement is mixed with an aqueous solution of ammonium phosphate. The mixture is allowed to set to form an amorphous cementitious material which also may be hydrothermally treated at a temperature of from about 120 C to about 300 C to form a crystal-containing phosphate-bonded material. Also described are the cementitious products of this method and the cement composition which includes aluminous cement and ammonium polyphosphate. 10 figures.

Embossed Teflon AF Laminate Membrane Microfluidic Diaphragm Valves

NASA Technical Reports Server (NTRS)

Willis, Peter; Hunt, Brian; White,Victor; Grunthaner, Frank

2008-01-01

A microfluidic system has been designed to survive spaceflight and to function autonomously on the Martian surface. It manipulates microscopic quantities of liquid water and performs chemical analyses on these samples to assay for the presence of molecules associated with past or present living processes. This technology lies at the core of the Urey Instrument, which is scheduled for inclusion on the Pasteur Payload of the ESA ExoMars rover mission in 2013. Fabrication processes have been developed to make the microfabricated Teflon-AF microfluidic diaphragm pumps capable of surviving extreme temperature excursions before and after exposure to liquid water. Two glass wafers are etched with features and a continuous Teflon membrane is sandwiched between them (see figure). Single valves are constructed using this geometry. The microfabricated devices are then post processed by heating the assembled device while applying pneumatic pressure to force the Teflon diaphragm against the valve seat while it is softened. After cooling the device, the embossed membrane retains this new shape. This solves previous problems with bubble introduction into the fluid flow where deformations of the membrane at the valve seat occurred during device bonding at elevated temperatures (100-150 C). The use of laminated membranes containing commercial Teflon AF 2400 sheet sandwiched between spun Teflon AF 1600 layers performed best, and were less gas permeable than Teflon AF 1600 membranes on their own. Spinning Teflon AF 1600 solution (6 percent in FLOURINERT(Registered TradeMark) FC40 solvent, 3M Company) at 500 rpm for 1.5 seconds, followed by 1,000 rpm for 3 seconds onto Borofloat glass wafers, results in a 10-micron-thick film of extremely smooth Teflon AF. This spinning process is repeated several times on flat, blank, glass wafers in order to gradually build a thick, smooth membrane. After running this process at least five times, the wafer and Teflon coating are heated under vacuum at 220 C for one hour in order to drive off any residual solvent present in the composite film. After this, a second blank, glass wafer is brought down from above and the stack is held under vacuum at 3 atm mechanical pressure for ten 10 hours.

Optical and electrical properties of ion beam textured Kapton and Teflon

NASA Technical Reports Server (NTRS)

Mirtich, M. J.; Sovey, J. S.

1977-01-01

Results are given for ion beam texturing of polyimide (Kapton) and fluorinated ethylene propylene (Teflon) by means of a 30-cm diam electron bombardment argon ion source. Ion beam-textured Kapton and Teflon surfaces are evaluated for various beam energies, current densities, and exposure times. The optical properties and sheet resistance are measured after each exposure. Provided in the paper are optical spectral data, resistivity measurements, calculated absorptance and emittance measurements, and surface structure SEM micrographs for various exposures to argon ions. It is found that Kapton becomes conducting and Teflon nonconducting when ion beam-textured. Textured Kapton exhibits large changes in the transmittance and solar absorptance, but only slight changes in reflectance. Surface texturing of Teflon may allow better adherence of subsequent sputtered metallic films for a high absorptance value. The results are valuable in spacecraft charging applications.

Bias-switchable negative and positive photoconductivity in 2D FePS3 ultraviolet photodetectors.

PubMed

Gao, Yi; Lei, Shuijin; Kang, Tingting; Fei, Linfeng; Mak, Chee-Leung; Yuan, Jian; Zhang, Mingguang; Li, Shaojuan; Bao, Qiaoliang; Zeng, Zhongming; Wang, Zhao; Gu, Haoshuang; Zhang, Kai

2018-06-15

Metal-phosphorus-trichalcogenides (MPTs), represented by NiPS 3 , FePS 3 , etc, are newly developed 2D wide-bandgap semiconductors and have been proposed as excellent candidates for ultraviolet (UV) optoelectronics. In spite of having superior advantages for solar-blind UV photodetectors, including those free of surface trap states, being highly compatible with versatile integrations as well as having an appropriate band gap, to date relevant study is rare. In this work, the photoresponse characteristic of UV detectors based on few-layer FePS 3 has been comprehensively investigated. The responsivity of the photodetector, which is observed to be determined by bias gate voltage, may achieve as high as 171.6 mAW -1 under the illumination of 254 nm weak light, which is comparable to most commercial UV detectors. Notably, both negative and positive photoconductivities exist in the FePS 3 photodetectors and can be controllably switched with bias voltage. The eminent and novel photoresponse property paves the way for the further development and practical use of 2D MPTs in high-performance UV photodetections.

Bias-switchable negative and positive photoconductivity in 2D FePS3 ultraviolet photodetectors

NASA Astrophysics Data System (ADS)

Gao, Yi; Lei, Shuijin; Kang, Tingting; Fei, Linfeng; Mak, Chee-Leung; Yuan, Jian; Zhang, Mingguang; Li, Shaojuan; Bao, Qiaoliang; Zeng, Zhongming; Wang, Zhao; Gu, Haoshuang; Zhang, Kai

2018-06-01

Metal-phosphorus-trichalcogenides (MPTs), represented by NiPS3, FePS3, etc, are newly developed 2D wide-bandgap semiconductors and have been proposed as excellent candidates for ultraviolet (UV) optoelectronics. In spite of having superior advantages for solar-blind UV photodetectors, including those free of surface trap states, being highly compatible with versatile integrations as well as having an appropriate band gap, to date relevant study is rare. In this work, the photoresponse characteristic of UV detectors based on few-layer FePS3 has been comprehensively investigated. The responsivity of the photodetector, which is observed to be determined by bias gate voltage, may achieve as high as 171.6 mAW‑1 under the illumination of 254 nm weak light, which is comparable to most commercial UV detectors. Notably, both negative and positive photoconductivities exist in the FePS3 photodetectors and can be controllably switched with bias voltage. The eminent and novel photoresponse property paves the way for the further development and practical use of 2D MPTs in high-performance UV photodetections.

Enzymatic Kinetic Isotope Effects from Path-Integral Free Energy Perturbation Theory.

PubMed

Gao, J

2016-01-01

Path-integral free energy perturbation (PI-FEP) theory is presented to directly determine the ratio of quantum mechanical partition functions of different isotopologs in a single simulation. Furthermore, a double averaging strategy is used to carry out the practical simulation, separating the quantum mechanical path integral exactly into two separate calculations, one corresponding to a classical molecular dynamics simulation of the centroid coordinates, and another involving free-particle path-integral sampling over the classical, centroid positions. An integrated centroid path-integral free energy perturbation and umbrella sampling (PI-FEP/UM, or simply, PI-FEP) method along with bisection sampling was summarized, which provides an accurate and fast convergent method for computing kinetic isotope effects for chemical reactions in solution and in enzymes. The PI-FEP method is illustrated by a number of applications, to highlight the computational precision and accuracy, the rule of geometrical mean in kinetic isotope effects, enhanced nuclear quantum effects in enzyme catalysis, and protein dynamics on temperature dependence of kinetic isotope effects. © 2016 Elsevier Inc. All rights reserved.

Method of preparing a sintered lithium aluminate structure for containing electrolyte

DOEpatents

Sim, James W.; Kinoshita, Kimio

1981-01-01

A porous sintered tile is formed of lithium aluminate for retaining molten lectrolyte within a fuel cell. The tile is prepared by reacting lithium hydroxide in aqueous solution with alumina particles to form beta lithium aluminate particles. The slurry is evaporated to dryness and the solids dehydrated to form a beta lithium aluminate powder. The powder is compacted into the desired shape and sintered at a temperature in excess of 1200 K. but less than 1900 K. to form a porous integral structure that is subsequently filled with molten electrolyte. A tile of this type is intended for use in containing molten alkali metal carbonates as electolyte for use in a fuel cell having porous metal or metal oxide electrodes for burning a fuel gas such as hydrogen and/or carbon monoxide with an oxidant gas containing oxygen.

Origins of saccharide-dependent hydration at aluminate, silicate, and aluminosilicate surfaces.

PubMed

Smith, Benjamin J; Rawal, Aditya; Funkhouser, Gary P; Roberts, Lawrence R; Gupta, Vijay; Israelachvili, Jacob N; Chmelka, Bradley F

2011-05-31

Sugar molecules adsorbed at hydrated inorganic oxide surfaces occur ubiquitously in nature and in technologically important materials and processes, including marine biomineralization, cement hydration, corrosion inhibition, bioadhesion, and bone resorption. Among these examples, surprisingly diverse hydration behaviors are observed for oxides in the presence of saccharides with closely related compositions and structures. Glucose, sucrose, and maltodextrin, for example, exhibit significant differences in their adsorption selectivities and alkaline reaction properties on hydrating aluminate, silicate, and aluminosilicate surfaces that are shown to be due to the molecular architectures of the saccharides. Solid-state (1)H, (13)C, (29)Si, and (27)Al nuclear magnetic resonance (NMR) spectroscopy measurements, including at very high magnetic fields (19 T), distinguish and quantify the different molecular species, their chemical transformations, and their site-specific adsorption on different aluminate and silicate moieties. Two-dimensional NMR results establish nonselective adsorption of glucose degradation products containing carboxylic acids on both hydrated silicates and aluminates. In contrast, sucrose adsorbs intact at hydrated silicate sites and selectively at anhydrous, but not hydrated, aluminate moieties. Quantitative surface force measurements establish that sucrose adsorbs strongly as multilayers on hydrated aluminosilicate surfaces. The molecular structures and physicochemical properties of the saccharides and their degradation species correlate well with their adsorption behaviors. The results explain the dramatically different effects that small amounts of different types of sugars have on the rates at which aluminate, silicate, and aluminosilicate species hydrate, with important implications for diverse materials and applications.

Vitamin D deficiency in first episode psychosis: a case-control study.

PubMed

Crews, Matthieu; Lally, John; Gardner-Sood, Poonam; Howes, Oliver; Bonaccorso, Stefania; Smith, Shubulade; Murray, Robin M; Di Forti, Marta; Gaughran, Fiona

2013-11-01

Vitamin D deficiency is seen in a high proportion of people with established psychotic disorders, but it is not known if this is present at onset of the illness. We set out to examine vitamin D levels in people with their first episode of psychosis (FEP). We conducted a matched case-control study to examine vitamin D levels and rates of vitamin D deficiency in sixty nine patients presenting with their FEP and sixty nine controls matched for age, sex and ethnicity. Differences between groups were tested using student's-t tests, paired t-tests and odds ratios for further analysis. Vitamin D levels were significantly lower in cases than in controls (p<0.001). The odds ratio of being vitamin D deficient was 2.99 in the FEP group relative to the control group. There was no correlation between vitamin D levels and length of hospitalisation in the patient group (r=-0.027, p=0.827). We found higher rates of vitamin D deficiency in people with FEP compared to matched controls. Given that vitamin D is neuroprotective; that developmental vitamin D deficiency may be a risk factor for psychosis, and that incipient psychosis may affect lifestyle factors and diet, future studies are required to examine this association further. In the meantime, there is a need for more widespread testing of vitamin D levels in FEP and for the development of appropriate management strategies. © 2013 Elsevier B.V. All rights reserved.

Spatial Working Memory Ability in Individuals at Ultra High Risk for Psychosis

PubMed Central

Goghari, Vina M.; Brett, Caroline; Tabraham, Paul; Johns, Louise; Valmaggia, Lucia; Broome, Matthew; Woolley, James; Bramon, Elvira; Howes, Oliver

2014-01-01

The goal of this investigation was to clarify the nature of spatial working memory difficulties in individuals at ultra high risk (UHR) for psychosis. We evaluated spatial working memory and intelligence in 96 individuals at UHR for psychosis, 28 patients with first episode psychosis (FEP), and 23 healthy controls. Fourteen UHR individuals developed a psychotic disorder during follow-up. Compared to controls, the UHR group was impaired in both the short-term maintenance of material and in the effective use of strategy, but not more immediate memory. These impairments were not as severe as those in the FEP group, as the UHR group performed better than the FEP group. A similar pattern of results was found for the intelligence measures. Discriminant function analyses demonstrated short-term maintenance of material significantly differentiated the UHR and healthy control groups even when accounting for full scale intelligence quotient (IQ); whereas full scale IQ significantly differentiated the UHR and FEP groups and FEP and control groups. Notably, within the UHR group, impaired spatial working memory performance was associated with lower global functioning, but not full scale IQ. The subgroup of UHR individuals who later developed psychosis was not significantly more impaired on any aspect of working memory performance than the group of UHR individuals who did not develop psychosis. Given, the relationship between spatial working memory deficits and functional outcome, these results indicate that cognitive remediation could be useful in individuals at UHR for psychosis to potentially improve functioning. PMID:24398256

Differential patterns of contextual organization of memory in first-episode psychosis.

PubMed

Murty, Vishnu P; McKinney, Rachel A; DuBrow, Sarah; Jalbrzikowski, Maria; Haas, Gretchen L; Luna, Beatriz

2018-02-15

Contextual information is used to support and organize episodic memory. Prior research has reliably shown memory deficits in psychosis; however, little research has characterized how this population uses contextual information during memory recall. We employed an approach founded in a computational framework of free recall to quantify how individuals with first episode of psychosis (FEP, N = 97) and controls (CON, N = 55) use temporal and semantic context to organize memory recall. Free recall was characterized using the Hopkins Verbal Learning Test-Revised (HVLT-R). We compared FEP and CON on three measures of free recall: proportion recalled, temporal clustering, and semantic clustering. Measures of temporal/semantic clustering quantified how individuals use contextual information to organize memory recall. We also assessed to what extent these measures relate to antipsychotic use and differentiated between different types of psychosis. We also explored the relationship between these measures and intelligence. In comparison to CON, FEP had reduced recall and less temporal clustering during free recall (p < 0.05, Bonferroni-corrected), and showed a trend towards greater semantic clustering (p = 0.10, Bonferroni-corrected). Within FEP, antipsychotic use and diagnoses did not differentiate between free recall accuracy or contextual organization of memory. IQ was related to free recall accuracy, but not the use of contextual information during recall in either group (p < 0.05, Bonferroni-corrected). These results show that in addition to deficits in memory recall, FEP differed in how they organize memories compared to CON.

Olfactory Functioning in First-Episode Psychosis.

PubMed

Kamath, Vidyulata; Lasutschinkow, Patricia; Ishizuka, Koko; Sawa, Akira

2018-04-06

Though olfactory deficits are well-documented in schizophrenia, fewer studies have examined olfactory performance profiles across the psychosis spectrum. The current study examined odor identification, discrimination, and detection threshold performance in first-episode psychosis (FEP) patients diagnosed with schizophrenia, schizoaffective disorder, bipolar disorder with psychotic features, major depression with psychotic features, and other psychotic conditions. FEP patients (n = 97) and healthy adults (n = 98) completed birhinal assessments of odor identification, discrimination, and detection threshold sensitivity for lyral and citralva. Participants also completed measures of anticipatory pleasure, anhedonia, and empathy. Differences in olfactory performances were assessed between FEP patients and controls and within FEP subgroups. Sex-stratified post hoc analyses were employed for a complete analysis of sex differences. Relationships between self-report measures and olfactory scores were also examined. Individuals with psychosis had poorer scores across all olfactory measures when compared to the control group. Within the psychosis cohort, patients with schizophrenia-associated psychosis had poorer odor identification, discrimination, and citralva detection threshold scores relative to controls. In schizophrenia patients, greater olfactory disturbance was associated with increased negative symptomatology, greater self-reported anhedonia, and lower self-reported anticipatory pleasure. Patients with mood-associated psychosis performed comparable to controls though men and women in this cohort showed differential olfactory profiles. These findings indicate that olfactory deficits extend beyond measures of odor identification in FEP with greater deficits observed in schizophrenia-related subgroups of psychosis. Studies examining whether greater olfactory dysfunction confers greater risk for developing schizophrenia relative to other forms of psychosis are warranted.

Dynamics of Ion Beam Charge Neutralization by Ferroelectric Plasma Sources

NASA Astrophysics Data System (ADS)

Stepanov, Anton D.; Gilson, Erik P.; Grisham, Larry R.; Kaganovich, Igor D.; Davidson, Ronald C.; Ji, Qing; Persaud, Arun; Seidl, Peter A.; Schenkel, Thomas

2016-10-01

Ferroelectric Plasma Sources (FEPSs) can generate plasma that provides effective space-charge neutralization of intense high-perveance ion beams. Here we present experimental results on charge neutralization of a high-perveance 38 keV Ar+ beam by a FEPS plasma. By comparing the measured beam radius with the envelope model for space-charge expansion, it is shown that a charge neutralization fraction of 98% is attainable. The transverse electrostatic potential of the ion beam is reduced from 15 V before neutralization to 0.3 V, implying that the energy of the neutralizing electrons is below 0.3 eV. Near-complete charge neutralization is established 5 μs after the driving pulse is applied to the FEPS, and can last for 35 μs. It is argued that the duration of neutralization is much longer than a reasonable lifetime of the plasma produced in the sub- μs surface discharge. Measurements of current flow in the driving circuit of the FEPS suggest that plasma can be generated for tens of μs after the high voltage pulse is applied. This is confirmed by fast photography of the plasma in the 1-meter long FEPS on NDCX-II, where effective charge neutralization of the beam was achieved with the optimized FEPS timing. This work was supported by the Office of Science of the US Department of Energy under contracts DE-AC0209CH11466 (PPPL) and DE-AC0205CH11231 (LBNL).

Impaired MMN/P3a complex in first-episode psychosis: cognitive and psychosocial associations.

PubMed

Hermens, Daniel F; Ward, Philip B; Hodge, M Antoinette Redoblado; Kaur, Manreena; Naismith, Sharon L; Hickie, Ian B

2010-08-16

Mismatch negativity (MMN) is a neurophysiological indicator of the brain's ability to extract relevant information from an irrelevant background. The P3a orienting response often accompanies MMN in deviance detection paradigms. Both MMN and P3a have been described as reliable biomarkers of schizophrenia. MMN/P3a impairments are associated with deficits in verbal memory and attentional switching, reflecting dysfunctions in the temporal and frontal systems, respectively. It remains unresolved whether MMN/P3a are robust biomarkers of psychosis in first-episode patients. Thirty-four young people (18 to 30years) were assessed in this study; 17 first-episode psychosis (FEP) patients were compared to 17 healthy controls. To elicit MMN/P3a, a two-tone passive auditory oddball paradigm with 8% duration deviants was used; event-related potentials were recorded at frontal, central and temporal (mastoid) sites. Neuropsychological assessments included processing speed, attentional switching, simple attention, and verbal learning and memory. Social functioning and quality of life measures were also obtained. The FEP group showed significantly reduced MMN amplitudes compared to controls. The FEP group also showed significantly reduced P3a amplitudes at frontal and central sites compared with controls. As expected, the FEP group also showed significant deficits in attention and verbal learning/memory. Correlational analyses found strong associations between fronto-central MMN/P3a peak amplitude and cognitive/psychosocial functioning. This study provides evidence of early neurobiological markers in young people with FEP. These findings suggest that MMN/P3a impairments are present at early stages of psychosis and that fundamental pre-attentive/deviance detection deficits may mark the beginning of progressive underlying changes with illness onset. Such deficits in FEP appear to have important links with higher-order cognitive and psychosocial functioning. Copyright (c) 2010 Elsevier Inc. All rights reserved.

NHEXAS PHASE I ARIZONA STUDY--STANDARD OPERATING PROCEDURE FOR FILTER WEIGHING (UA-L-9.1)

EPA Science Inventory

The purpose of this SOP is to describe the procedures to be followed in determining the pre- and post-exposure weight of 37mm and 25mm Teflon filters, Teflon sentinel filters and Teflon vacuum dust filters. This procedure applies to the pre- and post-exposure weighing of the fil...

Going Outside the TonB Box: Identification of Novel FepA-TonB Interactions In Vivo.

PubMed

Gresock, Michael G; Postle, Kathleen

2017-05-15

In Gram-negative bacteria, the cytoplasmic membrane protein TonB transmits energy derived from proton motive force to energize transport of important nutrients through TonB-dependent transporters in the outer membrane. Each transporter consists of a beta barrel domain and a lumen-occluding cork domain containing an essential sequence called the TonB box. To date, the only identified site of transporter-TonB interaction is between the TonB box and residues ∼158 to 162 of TonB. While the mechanism of ligand transport is a mystery, a current model based on site-directed spin labeling and molecular dynamics simulations is that, following ligand binding, the otherwise-sequestered TonB box extends into the periplasm for recognition by TonB, which mediates transport by pulling or twisting the cork. In this study, we tested that hypothesis with the outer membrane transporter FepA using in vivo photo-cross-linking to explore interactions of its TonB box and determine whether additional FepA-TonB interaction sites exist. We found numerous specific sites of FepA interaction with TonB on the periplasmic face of the FepA cork in addition to the TonB box. Two residues, T32 and A33, might constitute a ligand-sensitive conformational switch. The facts that some interactions were enhanced in the absence of ligand and that other interactions did not require the TonB box argued against the current model and suggested that the transport process is more complex than originally conceived, with subtleties that might provide a mechanism for discrimination among ligand-loaded transporters. These results constitute the first study on the dynamics of TonB-gated transporter interaction with TonB in vivo IMPORTANCE The TonB system of Gram-negative bacteria has a noncanonical active transport mechanism involving signal transduction and proteins integral to both membranes. To achieve transport, the cytoplasmic membrane protein TonB physically contacts outer membrane transporters such as FepA. Only one contact between TonB and outer membrane transporters has been identified to date: the TonB box at the transporter amino terminus. The TonB box has low information content, raising the question of how TonB can discriminate among multiple different TonB-dependent transporters present in the bacterium if it is the only means of contact. Here we identified several additional sites through which FepA contacts TonB in vivo , including two neighboring residues that may explain how FepA signals to TonB that ligand has bound. Copyright © 2017 American Society for Microbiology.

A drift chamber constructed of aluminized mylar tubes

NASA Astrophysics Data System (ADS)

Baringer, P.; Jung, C.; Ogren, H. O.; Rust, D. R.

1987-03-01

A thin reliable drift chamber has been constructed to be used near the interaction point of the PEP storage ring in the HRS detector. It is composed of individual drift tubes with aluminized mylar walls.

Evaluation of non-specular reflecting silvered Teflon and filled adhesives

NASA Technical Reports Server (NTRS)

Bourland, G.; Cox, R. L.

1981-01-01

A non-specular silver-Teflon tape thermal control coating was tested to provide the data necessary to qualify it for use on the Space Shuttle Orbiter radiators. Effects of cure cycle temperature and pressure on optical and mechanical properties on the silver-Teflon tape were evaluated. The baseline Permacel P-223 adhesive, used with the specular silver-Teflon tape initially qualified for the Orbiter radiators, and four alternate metal-filled and unfilled adhesives were evaluated. Tests showed the cure process has no effect on the silver-Teflon optical properties, and that the baseline adhesive cure cycle gives best results. In addition the P-223 adhesive bond is more reproducible than the alternates, and the non-specular tape meets both the mechanical and the optical requirements of the Orbiter radiator coating specification. Existing Orbiter coating techniques were demonstrated to be effective in aplying the non-specular tape to a curved panel simulating the radiators. Author

Eigenvalue Detonation of Combined Effects Aluminized Explosives

NASA Astrophysics Data System (ADS)

Capellos, C.; Baker, E. L.; Nicolich, S.; Balas, W.; Pincay, J.; Stiel, L. I.

2007-12-01

Theory and performance for recently developed combined—effects aluminized explosives are presented. Our recently developed combined-effects aluminized explosives (PAX-29C, PAX-30, PAX-42) are capable of achieving excellent metal pushing, as well as high blast energies. Metal pushing capability refers to the early volume expansion work produced during the first few volume expansions associated with cylinder and wall velocities and Gurney energies. Eigenvalue detonation explains the observed detonation states achieved by these combined effects explosives. Cylinder expansion data and thermochemical calculations (JAGUAR and CHEETAH) verify the eigenvalue detonation behavior.

Effect of aluminum substitution on the reflectance spectra of hematite

NASA Technical Reports Server (NTRS)

Morris, R. V.; Lauer, H. V., Jr.; Mendell, W. W.

1982-01-01

Hematite and aluminous hematite were synthesized and the diffuse reflectance spectra were recorded for the region between 0.35 and 1.20 microns. Results show that the near-IR based minimum for the aluminous hematite is shifted longward by about 0.02 microns and is much more shallow. Also, the aluminous specimen is considerably more reflective shortward of approximately 0.55 microns where the ferritic specimen is strongly absorbing. This is noteworthy since the visible slope and the red shoulder are often used in the construction of false color and band ratio images.

The Impact of FEP Legislation

ERIC Educational Resources Information Center

Adams, Arvil

1975-01-01

This testimony, before a public hearing of the New York City Commission on Human Rights in May 1974, had three express focuses: (1) on urban poverty among blacks in the non-south; (2) on the enforcement of Fair Employment Practice (FEP) legislation and its effect on the economic position of blacks and other minority groups; and, (3) on guidelines…

Regional Gray Matter Volume Deficits in Adolescents with First-Episode Psychosis

ERIC Educational Resources Information Center

Janssen, Joost; Parellada, Mara; Moreno, Dolores; Graell, Montserrat; Fraguas, David; Zabala, Arantzazu; Vazquez, Veronica Garcia; Desco, Manuel; Arango, Celso

2008-01-01

The regional gray matter volumes of adolescents with first-episode psychosis are compared with those of a control group. Magnetic resonance imaging was conducted on 70 patients with early onset FEP and on 51 individuals without FEP. Findings revealed that volume deficits in the left medial frontal gray matter were common in individuals with…

Corrosion of Spiral Rib Aluminized Pipe

DOT National Transportation Integrated Search

2012-08-01

Large diameter, corrugated steel pipes are a common sight in the culverts that run alongside many Florida roads. Spiral-ribbed aluminized pipe (SRAP) has been widely specified by the Florida Department of Transportation (FDOT) for runoff drainage. Th...

Corrosion of Spiral Rib Aluminized Pipe : [Summary

DOT National Transportation Integrated Search

2012-01-01

Large diameter, corrugated steel pipes are a common sight in the culverts that run alongside many Florida roads. Spiral-ribbed aluminized pipe (SRAP) has been widely specified by the Florida Department of Transportation (FDOT) for runoff drainage. Th...

Calcium aluminate coated and uncoated free form fabricated CoCr implants: a comparative study in rabbit.

PubMed

Palmquist, A; Jarmar, T; Hermansson, L; Emanuelsson, L; Taylor, A; Taylor, M; Engqvist, H; Thomsen, P

2009-10-01

The purpose of this study was to compare the integration in bone of uncoated free form fabricated cobalt chromium (CoCr) implants to the same implant with a calcium aluminate coating. The implants of cylindrical design with a pyramidal surface structure were press-fit into the limbs of New Zealand white rabbits. After 6 weeks, the rabbits were sacrificed, and samples were retrieved and embedded. Ground sections were subjected to histological analysis and histomorphometry. The section counter part was used for preparing an electron transparent transmission electron microscopy sample by focused ion beam milling. Calcium aluminate dip coating provided a significantly greater degree of bone contact than that of the native CoCr. The gibbsite hydrate formed in the hardening reaction of the calcium aluminate was found to be the exclusive crystalline phase material in direct contact with bone. (c) 2009 Wiley Periodicals, Inc.

Research on Equation of State For Detonation Products of Aluminized Explosive

NASA Astrophysics Data System (ADS)

Yue, Jun-Zheng; Duan, Zhuo-Ping; Zhang, Zhen-Yu; Ou, Zhuo-Cheng

2017-10-01

The secondary reaction of the aluminum powder contained in an aluminized explosive is investigated, from which the energy loss resulted from the quantity reduce of the gaseous products is demonstrated. Moreover, taking the energy loss into account, the existing improved Jones-Wilkins-Lee (JWL) equation of state for detonation products of aluminized explosive is modified. Furthermore, the new modified JWL equation of state is implemented into the dynamic analysis software (DYNA)-2D hydro-code to simulate numerically the metal plate acceleration tests of the Hexogen (RDX)-based aluminized explosives. It is found that the numerical results are in good agreement with previous experimental data. In addition, it is also demonstrated that the reaction rate of explosive before the Chapman-Jouget (CJ) state has little influence on the motion of the metal plate, based on which a simple approach is proposed to simulate numerically the products expansion process after the CJ state.

U.S.-MEXICO BORDER PROGRAM ARIZONA BORDER STUDY--STANDARD OPERATING PROCEDURE FOR FILTER WEIGHING (UA-L-9.1)

EPA Science Inventory

The purpose of this SOP is to describe the procedures to be followed in determining the pre- and post-exposure weight of 37mm and 25mm Teflon filters, Teflon sentinel filters and Teflon vacuum dust filters. This procedure applies to the pre- and post-exposure weighing of the fil...

HNS/Teflon, a new heat resistant explosive

NASA Technical Reports Server (NTRS)

Heller, H.; Bertram, A. L.

1973-01-01

HNS/Teflon (90/10) is a new pressed explosive developed for use in the Apollo program. The major advantages of HNS/Teflon are (1) excellent thermal stability at elevated temperatures, (2) superior resistance to sublimation at high temperatures and low pressures and (3) ease of molding powder preparation, pressing and machining. The impact sensitivity of HNS/Teflon is between that of Comp B and Comp A-3 while its explosive performance is about the same as TNT. Under the severe environmental conditions of the moon's surface, this explosive successfully performed its intended function of generating seismic waves in the Apollo ALSEP and LSPE experiments. (Modified author abstract)

Isentropic compression of argon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Veeser, L.R.; Ekdahl, C.A.; Oona, H.

1997-06-01

The compression was done in an MC-1 flux compression (explosive) generator, in order to study the transition from an insulator to a conductor. Since conductivity signals were observed in all the experiments (except when the probe is removed), both the Teflon and the argon are becoming conductive. The conductivity could not be determined (Teflon insulation properties unknown), but it could be bounded as being {sigma}=1/{rho}{le}8({Omega}cm){sub -1}, because when the Teflon breaks down, the dielectric constant is reduced. The Teflon insulator problem remains, and other ways to better insulate the probe or to measure the conductivity without a probe is beingmore » sought.« less

Software framework for the upcoming MMT Observatory primary mirror re-aluminization

NASA Astrophysics Data System (ADS)

Gibson, J. Duane; Clark, Dusty; Porter, Dallan

2014-07-01

Details of the software framework for the upcoming in-situ re-aluminization of the 6.5m MMT Observatory (MMTO) primary mirror are presented. This framework includes: 1) a centralized key-value store and data structure server for data exchange between software modules, 2) a newly developed hardware-software interface for faster data sampling and better hardware control, 3) automated control algorithms that are based upon empirical testing, modeling, and simulation of the aluminization process, 4) re-engineered graphical user interfaces (GUI's) that use state-of-the-art web technologies, and 5) redundant relational databases for data logging. Redesign of the software framework has several objectives: 1) automated process control to provide more consistent and uniform mirror coatings, 2) optional manual control of the aluminization process, 3) modular design to allow flexibility in process control and software implementation, 4) faster data sampling and logging rates to better characterize the approximately 100-second aluminization event, and 5) synchronized "real-time" web application GUI's to provide all users with exactly the same data. The framework has been implemented as four modules interconnected by a data store/server. The four modules are integrated into two Linux system services that start automatically at boot-time and remain running at all times. Performance of the software framework is assessed through extensive testing within 2.0 meter and smaller coating chambers at the Sunnyside Test Facility. The redesigned software framework helps ensure that a better performing and longer lasting coating will be achieved during the re-aluminization of the MMTO primary mirror.

Study of the affinity between the protein kinase PKA and homoarginine-containing peptides derived from kemptide: Free energy perturbation (FEP) calculations.

PubMed

Mena-Ulecia, Karel; Gonzalez-Norambuena, Fabian; Vergara-Jaque, Ariela; Poblete, Horacio; Tiznado, William; Caballero, Julio

2018-06-15

Protein kinases (PKs) discriminate between closely related sequences that contain serine, threonine, and/or tyrosine residues. Such specificity is defined by the amino acid sequence surrounding the phosphorylatable residue, so that it is possible to identify an optimal recognition motif (ORM) for each PK. The ORM for the protein kinase A (PKA), a well-known member of the PK family, is the sequence RRX(S/T)X, where arginines at the -3 and -2 positions play a key role with respect to the primed phosphorylation site. In this work, differential affinities of PKA for the peptide substrate Kemptide (LRRASLG) and mutants that substitute the arginine residues by the unnatural peptide homoarginine were evaluated through molecular dynamics (MD) and free energy perturbation (FEP) calculations. The FEP study for the homoarginine mutants required previous elaboration of a CHARMM "arginine to homoarginine" (R2B) hybrid topology file which is available in this manuscript as Supporting Information. Mutants substituting the arginine residues by alanine, lysine, and histidine were also considered in the comparison by using the same protocol. FEP calculations allowed estimating the free energy changes from the free PKA to PKA-substrate complex (ΔΔG E→ES ) when Kemptide structure was mutated. Both ΔΔG S→ES values for homoarginine mutants were predicted with a difference below 1 kcal/mol. In addition, FEP correctly predicted that all the studied mutations decrease the catalytic efficiency of Kemptide for PKA. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.

Suicide in first episode psychosis: a nationwide cohort study.

PubMed

Björkenstam, C; Björkenstam, E; Hjern, A; Bodén, R; Reutfors, J

2014-08-01

Relatively little is known about suicide in diagnostic subtypes of first episode psychosis (FEP). Our aim was to assess suicide rates and potential risk factors for suicide in FEP. This is a national register-based cohort study of patients born in 1973-1978 in Sweden and who were hospitalized with a FEP between ages 15 and 30years (n=2819). The patients were followed from date of discharge until death, emigration, or 31st of December 2008. The suicide rates for six diagnostic subtypes of FEP were calculated. Suicide incidence rate ratios (IRRs) were calculated to evaluate the association between suicide and psychiatric, familial, social, and demographic factors. In total 121 patients died by suicide. The overall suicide rate was 4.3 (95% confidence interval [CI] 3.5-5.0) per 1000person-years. The highest suicide rates were found in depressive disorder with psychotic symptoms and in delusional disorder. In an adjusted model, the strongest risk factors for suicide were self-harm (IRR 2.7, CI 1.7-4.4) or a conviction for violent crime (IRR 2.0, CI 1.3-3.2). Also having a first-degree relative with a schizophrenia/bipolar diagnosis (IRR 2.1, CI 1.2-3.6) or substance use disorder (IRR 2.0, CI 1.2-3.2) were significant risk factors for suicide. Impulsive behavior such as self-harm as well as having a family history of severe mental disorder or substance use are important risk factors for suicide in FEP. Copyright © 2014 Elsevier B.V. All rights reserved.

Heme oxygenase-1 upregulation modulates tone and fibroelastic properties of internal anal sphincter

PubMed Central

Krishna, Chadalavada Vijay; Singh, Jagmohan; Kumar, Sumit

2014-01-01

A compromise in the internal anal sphincter (IAS) tone and fibroelastic properties (FEP) plays an important role in rectoanal incontinence. Herein, we examined the effects of heme oxygenase (HO)-1 upregulation on these IAS characteristics in young rats. We determined the effect of HO-1 upregulator hemin on HO-1 mRNA and protein expressions and on basal IAS tone and its FEP before and after HO-1 inhibitor tin protoporphyrin IX. For FEP, we determined the kinetics of the IAS smooth muscle responses, by the velocities of relaxation, and recovery of the IAS tone following 0 Ca2+ and electrical field stimulation. To characterize the underlying signal transduction for these changes, we determined the effects of hemin on RhoA-associated kinase (RhoA)/Rho kinase (ROCK) II, myosin-binding subunit of myosin light chain phosphatase 1, fibronectin, and elastin expression levels. Hemin increased HO-1 mRNA and protein similar to the increases in the basal tone, and in the FEP of the IAS. Underlying mechanisms in the IAS characteristics are associated with increases in the genetic and translational expressions of RhoA/ROCKII, and elastin. Fibronectin expression levels on the other hand were found to be decreased following HO-1 upregulation. The results of our study show that the hemin/HO-1 system regulates the tone and FEP of IAS. The hemin/HO-1 system thus provides a potential target for the development of new interventions aimed at treatment of gastrointestinal motility disorders, specifically the age-related IAS dysfunction. PMID:25035109

The development of an inert simulant for HNS/teflon explosive

NASA Technical Reports Server (NTRS)

Elban, W. L.

1972-01-01

The report describes the development and evaluation of an inert simulant for the thermally stable, heat-resistant plastic-bonded explosive HNS/Teflon. The simulant is made by dry blending vinylidene fluoride, melamine and Teflon which when compared has a pressed density and thermal properties corresponding closely to the explosive. In addition, the machinability and handling characteristics of the simulant are similar to the explosive.

Duration of Untreated Psychosis Is Associated with More Negative Schizophrenia Symptoms after Acute Treatment for First-Episode Psychosis

ERIC Educational Resources Information Center

Grano, Niklas; Lindsberg, Jenni; Karjalainen, Marjaana; Gronroos, Peter; Blomberg, Ari-Pekka

2010-01-01

Evidence of association between duration of untreated psychosis (DUP) and negative symptoms of schizophrenia in first-episode psychosis (FEP) patients is inconsistent in the recent literature. In the present study, DUP, schizophrenia symptoms, duration of medication, and diagnosis were obtained from hospital archives in a sample of FEP patients.…

DEPRESSION OF THE PHOTIC AFTER DISCHARGE OF FLASH EVOKED POTENTIALS BY PHYSOSTIGMINE, CARBARYL AND PROPOXUR AND THE RELATIONSHIP TO INHIBITION OF BRAIN CHOLINESTERASE

EPA Science Inventory

The effects of N-methyl carbamate pesticides on the photic after discharge (PhAD) of flash evoked potentials (FEPs) and the relationship between inhibition of brain cholinesterase (ChE) activity and the PhAD were evaluated. FEPs were recorded in Long Evans rats treated with physo...

Very Long O-antigen Chains Enhance Fitness during Salmonella-induced Colitis by Increasing Bile Resistance

PubMed Central

Crawford, Robert W.; Keestra, A. Marijke; Winter, Sebastian E.; Xavier, Mariana N.; Tsolis, Renée M.; Tolstikov, Vladimir; Bäumler, Andreas J.

2012-01-01

Intestinal inflammation changes the luminal habitat for microbes through mechanisms that have not been fully resolved. We noticed that the FepE regulator of very long O-antigen chain assembly in the enteric pathogen Salmonella enterica serotype Typhimurium (S. Typhimurium) conferred a luminal fitness advantage in the mouse colitis model. However, a fepE mutant was not defective for survival in tissue, resistance to complement or resistance to polymyxin B. We performed metabolite profiling to identify changes in the luminal habitat that accompany S. Typhimurium-induced colitis. This analysis suggested that S. Typhimurium-induced colitis increased the luminal concentrations of total bile acids. A mutation in fepE significantly reduced the minimal inhibitory concentration (MIC) of S. Typhimurium for bile acids in vitro. Oral administration of the bile acid sequestrant cholestyramine resin lowered the concentrations of total bile acids in colon contents during S. Typhimurium infection and significantly reduced the luminal fitness advantage conferred by the fepE gene in the mouse colitis model. Collectively, these data suggested that very long O-antigen chains function in bile acid resistance of S. Typhimurium, a property conferring a fitness advantage during luminal growth in the inflamed intestine. PMID:23028318

In-situ carbon-coated Na2FeP2O7 anchored in three-dimensional reduced graphene oxide framework as a durable and high-rate sodium-ion battery cathode

NASA Astrophysics Data System (ADS)

Chen, Xiaobin; Du, Ke; Lai, Yanqing; Shang, Guozhi; Li, Huangxu; Xiao, Zhiwei; Chen, Yuxiang; Li, Junming; Zhang, Zhian

2017-07-01

Na2FeP2O7, which is considered as a promising cathode for sodium ion batteries (SIBs) on account of its economical efficiency and outstanding thermal stability, has been widely studied for the purpose of enhancing its electronic conductivity and interface ion transportation. In this paper, a double-carbon synergistically modified strategy was firstly introduced to facilitate the electrochemical performance of Na2FeP2O7. Na2FeP2O7 particles are enwrapped in situ by a carbon layer and further anchored in reduced graphene oxide (RGO) framework through a facile urea-nitrate combustion method. Consequently, the excellent rate performance and durable cycle stability of this compound are identified, which exhibits a reversible sodium storage capacity of 65 mAh g-1 at a current density of 10 C and no obvious decay in capacity after circling for 300 cycles at 1 C. What's more, no drastic degradation in capacity is observed when the cycling current density is brought back to high rates after cycling for more than 360 cycles at various rates.

Integrated fountain effect pump device for fluid management at low gravity

NASA Astrophysics Data System (ADS)

Yuan, S. W. K.; Frank, D. J.

1988-02-01

To transfer He II in space, the supply tank must be drained at low gravity. Conventional capillary devices such as the gallery system make use of the capillary retention capability of the screens for fluid management. Liquid helium is collected into gallery channels and then conveyed to the downstream fountain effect pump (FEP) or mechanical pump. In this Paper, a new fluid management device is proposed. The screens along the gallery channels are replaced by porous plugs which are responsible for both the fluid retention and pumping (by mechanical effect) of He II. No downstream pump is needed. The plugs in contact with liquid helium on both sides act as FEPs, and plugs exposed to vapour on one side behave as vapour-liquid phase separators (VLPSs). The total net transfer rate of He II into the receiving tank is the mass flow rate through the FEP minus the liquid loss from the VLPS plugs. The performance of the integrated FEP device (IFD) was analysed. The possibility of liquid breakthrough in the IFD was studied. The IFD is a very promising system for the fluid management of He II at low gravity.

Association Between Vitamin D Status and Schizophrenia: A First Psychotic Episode Study.

PubMed

Salavert, José; Grados, Dolors; Ramiro, Nuria; Carrión, Maria Isabel; Fadeuilhe, Christian; Palma, Felipe; López, Laura; Erra, Alba; Ramírez, Nicolás

2017-05-01

Vitamin D deficiency has been linked with schizophrenia. We aimed to determine whether patients with a first episode of psychosis (FEP) had lower vitamin D levels compared with controls considering their final diagnosis. We conducted a cross-sectional study determining 25-hydroxyvitamin D blood levels. 25-Hydroxyvitamin D levels were considered optimum at 20 ng/mL or greater. A group of 45 adult patients with FEP and a group of 22 healthy controls matched for age were recruited. The patient group was subdivided in two final diagnosis groups (schizophrenia versus other psychoses) after a 6-month follow-up. Average vitamin D values were deficient for FEP patients, especially those 22 with a final diagnosis of schizophrenia. These results relating vitamin D and schizophrenia generate interest to further examine this association.

Mechanisms for the adhesion of silver to glow discharge sensitized perfluorinated ethylene propylene (PEP)

NASA Technical Reports Server (NTRS)

Schutt, J. B.; Gilchrist, W. H.; Paczkowski, F. N.

1972-01-01

Details are given for the deposition of silver onto FEP for a batch coater capable of handling 864 square inches at a time. The effectiveness of the glow discharge is shown to be optimum when the FEP faces the anode. Using solid state theory based upon the work function difference, and the heuristic assumption that the surface of FEP is populated with fluoride ions, it is argued that an anode sensitized surface develops states receptive to electron transfer from silver, whereas a cathode sensitized surface is polarized only, and as a result cannot permanently trap charge. Thermodynamic arguments given show that an order of magnitude of 10 to the 9th power electrons are transferred into states to a depth of 10 nm.

Whole-Teflon microfluidic chips

PubMed Central

Ren, Kangning; Dai, Wen; Zhou, Jianhua; Su, Jing; Wu, Hongkai

2011-01-01

Although microfluidics has shown exciting potential, its broad applications are significantly limited by drawbacks of the materials used to make them. In this work, we present a convenient strategy for fabricating whole-Teflon microfluidic chips with integrated valves that show outstanding inertness to various chemicals and extreme resistance against all solvents. Compared with other microfluidic materials [e.g., poly(dimethylsiloxane) (PDMS)] the whole-Teflon chip has a few more advantages, such as no absorption of small molecules, little adsorption of biomolecules onto channel walls, and no leaching of residue molecules from the material bulk into the solution in the channel. Various biological cells have been cultured in the whole-Teflon channel. Adherent cells can attach to the channel bottom, spread, and proliferate well in the channels (with similar proliferation rate to the cells in PDMS channels with the same dimensions). The moderately good gas permeability of the Teflon materials makes it suitable to culture cells inside the microchannels for a long time. PMID:21536918

Ultras-stable Physical Vapor Deposited Amorphous Teflon Films with Extreme Fictive Temperature Reduction

NASA Astrophysics Data System (ADS)

McKenna, Gregory; Yoon, Heedong; Koh, Yung; Simon, Sindee

In the present work, we have produced highly stable amorphous fluoropolymer (Teflon AF® 1600) films to study the calorimetric and relaxation behavior in the deep in the glassy regime. Physical vapor deposition (PVD) was used to produce 110 to 700 nm PVD films with substrate temperature ranging from 0.70 Tg to 0.90 Tg. Fictive temperature (Tf) was measured using Flash DSC with 600 K/s heating and cooling rates. Consistent with prior observations for small molecular weight glasses, large enthalpy overshoots were observed in the stable amorphous Teflon films. The Tf reduction for the stable Teflon films deposited in the vicinity of 0.85 Tg was approximately 70 K compared to the Tgof the rejuvenated system. The relaxation behavior of stable Teflon films was measured using the TTU bubble inflation technique and following Struik's protocol in the temperature range from Tf to Tg. The results show that the relaxation time decreases with increasing aging time implying that devitrification is occurring in this regime.

Evaluation of commercially supplied silver coated Teflon for spacecraft temperature control usage

NASA Technical Reports Server (NTRS)

Heaney, J. B.

1974-01-01

A series of tests are described which were performed to evaluate the acceptability of a commercially supplied silver backed teflon thermal control coating relative to teflon previously coated at GSFC. Optical measurements made on numerous samples indicate that the commercial material possesses an average solar absorptance of 0.085, an emittance of 0.76 and an average alpha/epsilon equal to 0.112, all of which are equivalent to the GSFC coated teflon. The emittance of the protective inconel backing was found to be 0.037. The coating is shown to have good adhesion at the Ag-teflon interface and exposure to UV irradiation uncovered no coating irregularities. Temperature cycling over the range -135 C to +200 C produced crazing in the evaporated Ag layer as expected but no delamination was observed. The suitability of Mystik no. 7366 and 3M no. 467 adhesives as bonding agents for the metallized polymer is demonstrated. Various problems associated with production reproducibility and selection of a proper bonding process are discussed.

The effect of ambient ozone and humidity on the performance of nylon and Teflon filters used in ambient air monitoring filter-pack systems

Treesearch

PE Padgett

2010-01-01

Nylon and Teflon filter media are frequently used for monitoring ambient air pollutants. These media are subject to many environmental factors that may influence adsorption and retention of particulate and gaseous nitrogenous pollutants. This study evaluated the effects of ozone and humidity on the efficacy of nylon and Teflon filters used in the US dry deposition...

Excimer laser with fluoropolymer lining

DOEpatents

Sze, Robert C.

1982-01-01

A cavity formed of Teflon to provide extended static fill lifetimes for gases containing halogens. A double cavity configuration provides structural integrity to the inner Teflon cavity by maintaining an identical multi-atmospheric pressure within the outer structural cavity to minimize tension on the Teflon inner cavity. Use of a quantity of the lasing gas in the outer cavity or a constituent of that gas minimizes contamination of the lasing gas.

SINTERING AND SULFATION OF CALCIUM SILICATE-ALUMINATE

EPA Science Inventory

The effect of sintering on the reactivity of solids at high temperature was studied. The nature of the interaction was studied with calcium silicate-aluminate reacting with SO2 between 665 and 800 C. The kinetics of the sintering and sulfation processes were measured independentl...

Ion microprobe analyses of aluminous lunar glasses - A test of the 'rock type' hypothesis

NASA Technical Reports Server (NTRS)

Meyer, C., Jr.

1978-01-01

Previous soil survey investigations found that there are natural groupings of glass compositions in lunar soils and that the average major element composition of some of these groupings is the same at widely separated lunar landing sites. This led soil survey enthusiasts to promote the hypothesis that the average composition of glass groupings represents the composition of primary lunar 'rock types'. In this investigation the trace element composition of numerous aluminous glass particles was determined by the ion microprobe method as a test of the above mentioned 'rock type' hypothesis. It was found that within any grouping of aluminous lunar glasses by major element content, there is considerable scatter in the refractory trace element content. In addition, aluminous glasses grouped by major elements were found to have different average trace element contents at different sites (Apollo 15, 16 and Luna 20). This evidence argues that natural groupings in glass compositions are determined by regolith processes and may not represent the composition of primary lunar 'rock types'.

Methods of use of calcium hexa aluminate refractory linings and/or chemical barriers in high alkali or alkaline environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGowan, Kenneth A; Cullen, Robert M; Keiser, James R

A method for improving the insulating character/and or penetration resistance of a liner in contact with at least one of an alkali and/or alkaline environments is provided. The method comprises lining a surface that is subject to wear by an alkali environment and/or an alkaline environment with a refractory composition comprising a refractory aggregate consisting essentially of a calcium hexa aluminate clinker having the formula CA.sub.6, wherein C is equal to calcium oxide, wherein A is equal to aluminum oxide, and wherein the hexa aluminate clinker has from zero to less than about fifty weight percent C.sub.12A.sub.7, and wherein greatermore » than 98 weight percent of the calcium hexa aluminate clinker having a particle size ranging from -20 microns to +3 millimeters, for forming a liner of the surface. This method improves the insulating character/and or penetration resistance of the liner.« less

Hydration of Portland cement with additions of calcium sulfoaluminates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Le Saout, Gwenn, E-mail: gwenn.le-saout@mines-ales.fr; Lothenbach, Barbara; Hori, Akihiro

2013-01-15

The effect of mineral additions based on calcium aluminates on the hydration mechanism of ordinary Portland cement (OPC) was investigated using isothermal calorimetry, thermal analysis, X-ray diffraction, scanning electron microscopy, solid state nuclear magnetic resonance and pore solution analysis. Results show that the addition of a calcium sulfoaluminate cement (CSA) to the OPC does not affect the hydration mechanism of alite but controls the aluminate dissolution. In the second blend investigated, a rapid setting cement, the amorphous calcium aluminate reacts very fast to ettringite. The release of aluminum ions strongly retards the hydration of alite but the C-S-H has amore » similar composition as in OPC with no additional Al to Si substitution. As in CSA-OPC, the aluminate hydration is controlled by the availability of sulfates. The coupling of thermodynamic modeling with the kinetic equations predicts the amount of hydrates and pore solution compositions as a function of time and validates the model in these systems.« less

Characteristics of edge breakdowns on Teflon samples

NASA Technical Reports Server (NTRS)

Yadlowsky, E. J.; Hazelton, R. C.; Churchill, R. J.

1980-01-01

The characteristics of electrical discharges induced on silverbacked Teflon samples irradiated by a monoenergetic electron beam have been studied under controlled laboratory conditions. Measurements of breakdown threshold voltages indicate a marked anisotropy in the electrical breakdown properties of Teflon: differences of up to 10 kV in breakdown threshold voltage are observed depending on the sample orientation. The material anisotropy can be utilized in spacecraft construction to reduce the magnitude of discharge currents.

The Bond Strength of Composite Resin to Dental Casting Alloys Using an Electro-Chemical Tin Plating System.

DTIC Science & Technology

1985-06-01

of Opaque-Adhesive Containing Opaque Powder ..................... 36 Figure 12. Isosit Resin Condensed into Teflon Tubes ..... 37 Figure 13. Device...millimeter long teflon tube was positioned centrally on each specimen. The Isosit body resin was condensed into the tube using the blunt end of a...8217.*. .’-~ ~**.*~.**.**.*~.**.*%~ 37 Figure 12. Isosit Resin Condensed into Teflon Tubes Wy~WW’. WVtTh. .. . - . - S.. * ***’h.).’ *.~’b

Mechanical impact tests of materials in oxygen effects of contamination. [Teflon, stainless steel, and aluminum

NASA Technical Reports Server (NTRS)

Ordin, P. M.

1980-01-01

The effect of contaminants on the mechanical impact sensitivity of Teflon, stainless steel, and aluminum in a high-pressure oxygen environment was investigated. Uncontaminated Teflon did not ignite under the test conditions. The liquid contaminants - cutting oil, motor lubricating oil, and toolmaker dye - caused Teflon to ignite. Raising the temperature lowered the impact energy required for ignition. Stainless steel was insensitive to ignition under the test conditions with the contaminants used. Aluminum appeared to react without contaminants under certain test conditions; however, contamination with cutting oil, motor lubricating oil, and toolmakers dye increased the sensitivity of aluminum to mechanical impact. The grit contaminants silicon dioxide and copper powder did not conclusively affect the sensitivity of aluminum.

Do the same factors predict outcome in schizophrenia and non-schizophrenia syndromes after first-episode psychosis? A two-year follow-up study.

PubMed

Peña, Javier; Segarra, Rafael; Ojeda, Natalia; García, Jon; Eguiluz, José I; Gutiérrez, Miguel

2012-06-01

The aim of this two-year longitudinal study was to identify the best baseline predictors of functional outcome in first-episode psychosis (FEP). We tested whether the same factors predict functional outcomes in two different subsamples of FEP patients: schizophrenia and non-schizophrenia syndrome groups. Ninety-five patients with FEP underwent a full clinical evaluation (i.e., PANSS, Mania, Depression and Insight). Functional outcome measurements included the WHO Disability Assessment Schedule (DAS-WHO), Global Assessment of Functioning (GAF) and Clinical Global Impression (CGI). Estimation of cognition was obtained by a neuropsychological battery which included attention, processing speed, language, memory and executive functioning. Greater severity of visuospatial functioning at baseline predicted poorer functional outcome as measured by the three functional scales (GAF, CGI and DAS-WHO) in the pooled FEP sample (explaining ut to the 12%, 9% and 10% of the variance, respectively). Negative symptoms also effectively contributed to predict GAF scores (8%). However, we obtained different predictive values after differentiating sample diagnoses. Processing speed significantly predicted most functional outcome measures in patients with schizophrenia, whereas visuospatial functioning was the only significant predictor of functional outcomes in the non-schizophrenia subgroup. Our results suggest that processing speed, visuospatial functioning and negative symptoms significantly (but differentially) predict outcomes in patients with FEP, depending on their clinical progression. For patients without a schizophrenia diagnosis, visuospatial functioning was the best predictor of functional outcome. The performance on processing speed seemed to be a key factor in more severe syndromes. However, only a small proportion of the variance could be explained by the model, so there must be many other factors that have to be considered. Copyright © 2012 Elsevier Ltd. All rights reserved.

Elevated Myo-Inositol, Choline, and Glutamate Levels in the Associative Striatum of Antipsychotic-Naive Patients With First-Episode Psychosis: A Proton Magnetic Resonance Spectroscopy Study With Implications for Glial Dysfunction

PubMed Central

Plitman, Eric; de la Fuente-Sandoval, Camilo; Reyes-Madrigal, Francisco; Chavez, Sofia; Gómez-Cruz, Gladys; León-Ortiz, Pablo; Graff-Guerrero, Ariel

2016-01-01

Glial disturbances are highly implicated in the pathophysiology of schizophrenia and may be linked with glutamatergic dysregulation. Myo-inositol (mI), a putative marker of glial cells, and choline (Cho), representative of membrane turnover, are both present in larger concentrations within glial cells than in neurons, and their elevation is often interpreted to reflect glial activation. Proton magnetic resonance spectroscopy (1H-MRS) allows for the evaluation of mI, Cho, glutamate, glutamate + glutamine (Glx), and N-acetylaspartate (NAA). A collective investigation of these measures in antipsychotic-naive patients experiencing their first nonaffective episode of psychosis (FEP) can improve the understanding of glial dysfunction and its implications in the early stages of schizophrenia. 3-Tesla 1H-MRS (echo time = 35ms) was performed in 60 antipsychotic-naive patients with FEP and 60 age- and sex-matched healthy controls. mI, Cho, glutamate, Glx, and NAA were estimated using LCModel and corrected for cerebrospinal fluid composition within the voxel. mI, Cho, and glutamate were elevated in the FEP group. After correction for multiple comparisons, mI positively correlated with grandiosity. The relationships between mI and glutamate, and Cho and glutamate, were more positive in the FEP group. These findings are suggestive of glial activation in the absence of neuronal loss and may thereby provide support for the presence of a neuroinflammatory process within the early stages of schizophrenia. Dysregulation of glial function might result in the disruption of glutamatergic neurotransmission, which may influence positive symptomatology in patients with FEP. PMID:26320195

Elevated Myo-Inositol, Choline, and Glutamate Levels in the Associative Striatum of Antipsychotic-Naive Patients With First-Episode Psychosis: A Proton Magnetic Resonance Spectroscopy Study With Implications for Glial Dysfunction.

PubMed

Plitman, Eric; de la Fuente-Sandoval, Camilo; Reyes-Madrigal, Francisco; Chavez, Sofia; Gómez-Cruz, Gladys; León-Ortiz, Pablo; Graff-Guerrero, Ariel

2016-03-01

Glial disturbances are highly implicated in the pathophysiology of schizophrenia and may be linked with glutamatergic dysregulation. Myo-inositol (mI), a putative marker of glial cells, and choline (Cho), representative of membrane turnover, are both present in larger concentrations within glial cells than in neurons, and their elevation is often interpreted to reflect glial activation. Proton magnetic resonance spectroscopy ((1)H-MRS) allows for the evaluation of mI, Cho, glutamate, glutamate + glutamine (Glx), and N-acetylaspartate (NAA). A collective investigation of these measures in antipsychotic-naive patients experiencing their first nonaffective episode of psychosis (FEP) can improve the understanding of glial dysfunction and its implications in the early stages of schizophrenia. 3-Tesla (1)H-MRS (echo time = 35 ms) was performed in 60 antipsychotic-naive patients with FEP and 60 age- and sex-matched healthy controls. mI, Cho, glutamate, Glx, and NAA were estimated using LCModel and corrected for cerebrospinal fluid composition within the voxel. mI, Cho, and glutamate were elevated in the FEP group. After correction for multiple comparisons, mI positively correlated with grandiosity. The relationships between mI and glutamate, and Cho and glutamate, were more positive in the FEP group. These findings are suggestive of glial activation in the absence of neuronal loss and may thereby provide support for the presence of a neuroinflammatory process within the early stages of schizophrenia. Dysregulation of glial function might result in the disruption of glutamatergic neurotransmission, which may influence positive symptomatology in patients with FEP. © The Author 2015. Published by Oxford University Press on behalf of the Maryland Psychiatric Research Center. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Estimation of relative free energies of binding using pre-computed ensembles based on the single-step free energy perturbation and the site-identification by Ligand competitive saturation approaches.

PubMed

Raman, E Prabhu; Lakkaraju, Sirish Kaushik; Denny, Rajiah Aldrin; MacKerell, Alexander D

2017-06-05

Accurate and rapid estimation of relative binding affinities of ligand-protein complexes is a requirement of computational methods for their effective use in rational ligand design. Of the approaches commonly used, free energy perturbation (FEP) methods are considered one of the most accurate, although they require significant computational resources. Accordingly, it is desirable to have alternative methods of similar accuracy but greater computational efficiency to facilitate ligand design. In the present study relative free energies of binding are estimated for one or two non-hydrogen atom changes in compounds targeting the proteins ACK1 and p38 MAP kinase using three methods. The methods include standard FEP, single-step free energy perturbation (SSFEP) and the site-identification by ligand competitive saturation (SILCS) ligand grid free energy (LGFE) approach. Results show the SSFEP and SILCS LGFE methods to be competitive with or better than the FEP results for the studied systems, with SILCS LGFE giving the best agreement with experimental results. This is supported by additional comparisons with published FEP data on p38 MAP kinase inhibitors. While both the SSFEP and SILCS LGFE approaches require a significant upfront computational investment, they offer a 1000-fold computational savings over FEP for calculating the relative affinities of ligand modifications once those pre-computations are complete. An illustrative example of the potential application of these methods in the context of screening large numbers of transformations is presented. Thus, the SSFEP and SILCS LGFE approaches represent viable alternatives for actively driving ligand design during drug discovery and development. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Neuropsychological assessment of memory in child and adolescent first episode psychosis: cannabis and «the paradox effect».

PubMed

Moreno-Granados, Josefa María; Ferrín, Maite; Salcedo-Marín, Dolores M; Ruiz-Veguilla, Miguel

2014-01-01

The importance of neuropsychological functioning in First-Episode Psychosis (FEP) has led to the publication of a growing number of studies in this area of research. The present study pursued three goals: First, to examine verbal and visual memory in a sample of Child and Adolescent FEP, second, to evaluate the effect of other cognitive domains on verbal and visual memory, and finally, to examine the relationship between performance in this cognitive dimension and the use of cannabis at this age. A sample of 41 FEPs and 39 healthy subjects were evaluated. The variables assessed were verbal and visual memory, attention, working memory, processing speed, mental flexibility, verbal fluency, motor coordination, planning ability and intelligence. Our results found impairment of short and long-term recall of verbal memory, and short-term visual memory in early psychosis. They also found relationships between cognitive dimensions, such as visual memory and intelligence and motor coordination. Finally, a «paradoxical» effect was found in patients who used cannabis, as the FEP consumers performed the visual memory test better than those who had not used it. Patients showed impairment of short and long-term recall of verbal information and short-term visual reproduction. In the second place, motor coordination and intelligence influenced short-term visual memory in patients in the early stages of the illness. Third, use of cannabis in patients with FEP was associated with better performance in the test that evaluated the short-term visual memory, as measured by task completion time, that is, efficiency in performing the test. However, when measured by task execution accuracy, their visual memory was no better than the controls. Copyright © 2012 SEP y SEPB. Published by Elsevier España. All rights reserved.

Confined Mobility of TonB and FepA in Escherichia coli Membranes

PubMed Central

Lill, Yoriko; Jordan, Lorne D.; Smallwood, Chuck R.; Newton, Salete M.; Lill, Markus A.; Klebba, Phillip E.; Ritchie, Ken

2016-01-01

The important process of nutrient uptake in Escherichia coli, in many cases, involves transit of the nutrient through a class of beta-barrel proteins in the outer membrane known as TonB-dependent transporters (TBDTs) and requires interaction with the inner membrane protein TonB. Here we have imaged the mobility of the ferric enterobactin transporter FepA and TonB by tracking them in the membranes of live E. coli with single-molecule resolution at time-scales ranging from milliseconds to seconds. We employed simple simulations to model/analyze the lateral diffusion in the membranes of E.coli, to take into account both the highly curved geometry of the cell and artifactual effects expected due to finite exposure time imaging. We find that both molecules perform confined lateral diffusion in their respective membranes in the absence of ligand with FepA confined to a region 0.180−0.007+0.006 μm in radius in the outer membrane and TonB confined to a region 0.266−0.009+0.007 μm in radius in the inner membrane. The diffusion coefficient of these molecules on millisecond time-scales was estimated to be 21−5+9 μm2/s and 5.4−0.8+1.5 μm2/s for FepA and TonB, respectively, implying that each molecule is free to diffuse within its domain. Disruption of the inner membrane potential, deletion of ExbB/D from the inner membrane, presence of ligand or antibody to FepA and disruption of the MreB cytoskeleton was all found to further restrict the mobility of both molecules. Results are analyzed in terms of changes in confinement size and interactions between the two proteins. PMID:27935943

Confined Mobility of TonB and FepA in Escherichia coli Membranes.

PubMed

Lill, Yoriko; Jordan, Lorne D; Smallwood, Chuck R; Newton, Salete M; Lill, Markus A; Klebba, Phillip E; Ritchie, Ken

2016-01-01

The important process of nutrient uptake in Escherichia coli, in many cases, involves transit of the nutrient through a class of beta-barrel proteins in the outer membrane known as TonB-dependent transporters (TBDTs) and requires interaction with the inner membrane protein TonB. Here we have imaged the mobility of the ferric enterobactin transporter FepA and TonB by tracking them in the membranes of live E. coli with single-molecule resolution at time-scales ranging from milliseconds to seconds. We employed simple simulations to model/analyze the lateral diffusion in the membranes of E.coli, to take into account both the highly curved geometry of the cell and artifactual effects expected due to finite exposure time imaging. We find that both molecules perform confined lateral diffusion in their respective membranes in the absence of ligand with FepA confined to a region [Formula: see text] μm in radius in the outer membrane and TonB confined to a region [Formula: see text] μm in radius in the inner membrane. The diffusion coefficient of these molecules on millisecond time-scales was estimated to be [Formula: see text] μm2/s and [Formula: see text] μm2/s for FepA and TonB, respectively, implying that each molecule is free to diffuse within its domain. Disruption of the inner membrane potential, deletion of ExbB/D from the inner membrane, presence of ligand or antibody to FepA and disruption of the MreB cytoskeleton was all found to further restrict the mobility of both molecules. Results are analyzed in terms of changes in confinement size and interactions between the two proteins.

Brain-relevant antibodies in first-episode psychosis: a matched case-control study.

PubMed

Gaughran, Fiona; Lally, John; Beck, Katherine; McCormack, Ruaidhri; Gardner-Sood, Poonam; Coutinho, Ester; Jacobson, Leslie; Lang, Bethan; Sainz-Fuertes, Ricardo; Papanastasiou, Evangelos; Di Forti, Marta; Nicholson, Tim; Vincent, Angela; Murray, Robin M

2018-06-01

There has been much recent excitement about the possibility that some cases of psychosis may be wholly due to brain-reactive antibodies, with antibodies to N-methyl-D-aspartate receptor (NMDAR) and the voltage-gated potassium channel (VGKC)-complex reported in a few patients with first-episode psychosis (FEP). Participants were recruited from psychiatric services in South London, UK, from 2009 to 2011 as part of the Genetics and Psychosis study. We conducted a case-control study to examine NMDAR and VGKC-complex antibody levels and rates of antibody positivity in 96 patients presenting with FEP and 98 controls matched for age and sex. Leucine-rich glioma inactiviated-1 (LGI1) and contactin-associated protein (CASPR) antibodies were also measured. Notably, patients with suspicion of organic disease were excluded. VGKC-complex antibodies were found in both cases (n = 3) and controls (n = 2). NMDAR antibody positivity was seen in one case and one control. Either LGI1-Abs or CASPR2-Abs were found in three cases and three controls. Neuronal antibody staining, consistent with the above results or indicating potential novel antigens, was overall positive in four patients but also in six controls. Overall, antibody positivity was at low levels only and not higher in cases than in controls. This case-control study of the prevalence of antibodies in FEP does not provide evidence to support the hypothesis that FEP is associated with an immune-mediated process in a subgroup of patients. Nevertheless, as other bio-clinical factors may influence the effect of such antibodies in a given individual, and patients with organic neurological disease may be misdiagnosed as FEP, the field requires more research to put these findings in context.

Relationship between plasma homovanillic acid and outcome in patients with psychosis spectrum disorders.

PubMed

van de Kerkhof, Nora W A; Fekkes, Durk; van der Heijden, Frank M M A; Egger, Jos I M; Verhoeven, Willem M A

2015-01-01

Psychosis spectrum disorders, especially schizophrenia, have been linked to disturbed dopaminergic activity in the brain. Plasma homovanillic acid (pHVA) levels partly represent dopaminergic metabolism in the central nervous system. In the present study associations between (changes in) pHVA levels, symptom severity and symptomatic improvement in patients with psychoses were investigated. From a total of 80 patients, 58 fulfilled all inclusion criteria and their symptom profile and severity were assessed by means of the Comprehensive Assessment of Symptoms and History (CASH), the Positive and Negative Syndrome Scale (PANSS) and the Clinical Global Impression Scale for Severity and Improvement (CGI-S/CGI-I) at baseline and after 6 weeks of antipsychotic treatment. After inclusion, all patients were prescribed first- or second-generation antipsychotics by their treating psychiatrist. A total of 12 patients had first-episode psychosis (FEP). At both time points, pHVA levels were measured. Subsequently, pHVA levels were compared with an age-matched control sample and changes in pHVA levels (ΔpHVA) after treatment were associated with clinical parameters. Before analyses, data were scrutinized for possible confounders, particularly gender, smoking, medication status (including antipsychotic class), and recent drug use. The pHVA levels in patients were not different from those in controls. Treatment resulted in a significant decrease of all parameters. Symptomatic improvement as well as ΔpHVA was most pronounced in FEP patients. These findings show that patients with FEP have a more favourable outcome than non-FEP patients and that greater ΔpHVA also suggests that FEP patients still have the capacity to adjust dopaminergic neurotransmission. © 2015 S. Karger AG, Basel.

Differences in Facial Emotion Recognition between First Episode Psychosis, Borderline Personality Disorder and Healthy Controls.

PubMed

Catalan, Ana; Gonzalez de Artaza, Maider; Bustamante, Sonia; Orgaz, Pablo; Osa, Luis; Angosto, Virxinia; Valverde, Cristina; Bilbao, Amaia; Madrazo, Arantza; van Os, Jim; Gonzalez-Torres, Miguel Angel

2016-01-01

Facial emotion recognition (FER) is essential to guide social functioning and behaviour for interpersonal communication. FER may be altered in severe mental illness such as in psychosis and in borderline personality disorder patients. However, it is unclear if these FER alterations are specifically related to psychosis. Awareness of FER alterations may be useful in clinical settings to improve treatment strategies. The aim of our study was to examine FER in patients with severe mental disorder and their relation with psychotic symptomatology. Socio-demographic and clinical variables were collected. Alterations on emotion recognition were assessed in 3 groups: patients with first episode psychosis (FEP) (n = 64), borderline personality patients (BPD) (n = 37) and healthy controls (n = 137), using the Degraded Facial Affect Recognition Task. The Positive and Negative Syndrome Scale, Structured Interview for Schizotypy Revised and Community Assessment of Psychic Experiences scales were used to assess positive psychotic symptoms. WAIS III subtests were used to assess IQ. Kruskal-Wallis analysis showed a significant difference between groups on the FER of neutral faces score between FEP, BPD patients and controls and between FEP patients and controls in angry face recognition. No significant differences were found between groups in the fear or happy conditions. There was a significant difference between groups in the attribution of negative emotion to happy faces. BPD and FEP groups had a much higher tendency to recognize happy faces as negatives. There was no association with the different symptom domains in either group. FEP and BPD patients have problems in recognizing neutral faces more frequently than controls. Moreover, patients tend to over-report negative emotions in recognition of happy faces. Although no relation between psychotic symptoms and FER alterations was found, these deficits could contribute to a patient's misinterpretations in daily life.

Virulence-related genes, adhesion and invasion of some Yersinia enterocolitica-like strains suggests its pathogenic potential.

PubMed

Imori, Priscilla F M; Passaglia, Jaqueline; Souza, Roberto A; Rocha, Lenaldo B; Falcão, Juliana P

2017-03-01

Yersina enterocolitica-like species have not been extensively studied regarding its pathogenic potential. This work aimed to assess the pathogenic potential of some Y. enterocolitica-like strains by evaluating the presence of virulence-related genes by PCR and their ability to adhere to and invade Caco-2 and HEp-2 cells. A total of 50 Y. frederiksenii, 55 Y. intermedia and 13 Y. kristensenii strains were studied. The strains contained the following genes: Y. frederiksenii, fepA(44%), fes(44%) and ystB(18%); Y. intermedia, ail(53%), fepA (35%), fepD(2%), fes(97%), hreP(2%), ystB(2%) and tccC(35%); Y. kristensenii, ail(62%), ystB(23%), fepA(77%), fepD(54%), fes(54%) and hreP(77%). Generally, the Y. enterocolitica-like strains had a reduced ability to adhere to and invade mammalian cells compared to the highly pathogenic Y. enterocolitica 8081. However, Y. kristensenii FCF410 and Y. frederiksenii FCF461 presented high invasion potentials in Caco-2 cells after five days of pre-incubation increased by 45- and 7.2-fold compared to Y. enterocolitica 8081, respectively; but, the ail gene was not detected in these strains. The presence of virulence-related genes in some of the Y. enterocolitica-like strains indicated their possible pathogenic potential. Moreover, the results suggest the existence of alternative virulence mechanisms and that the pathogenicity of Y. kristensenii and Y. frederiksenii may be strain-dependent. Copyright © 2017 Elsevier Ltd. All rights reserved.

Free Energy Perturbation Hamiltonian Replica-Exchange Molecular Dynamics (FEP/H-REMD) for Absolute Ligand Binding Free Energy Calculations.

PubMed

Jiang, Wei; Roux, Benoît

2010-07-01

Free Energy Perturbation with Replica Exchange Molecular Dynamics (FEP/REMD) offers a powerful strategy to improve the convergence of free energy computations. In particular, it has been shown previously that a FEP/REMD scheme allowing random moves within an extended replica ensemble of thermodynamic coupling parameters "lambda" can improve the statistical convergence in calculations of absolute binding free energy of ligands to proteins [J. Chem. Theory Comput. 2009, 5, 2583]. In the present study, FEP/REMD is extended and combined with an accelerated MD simulations method based on Hamiltonian replica-exchange MD (H-REMD) to overcome the additional problems arising from the existence of kinetically trapped conformations within the protein receptor. In the combined strategy, each system with a given thermodynamic coupling factor lambda in the extended ensemble is further coupled with a set of replicas evolving on a biased energy surface with boosting potentials used to accelerate the inter-conversion among different rotameric states of the side chains in the neighborhood of the binding site. Exchanges are allowed to occur alternatively along the axes corresponding to the thermodynamic coupling parameter lambda and the boosting potential, in an extended dual array of coupled lambda- and H-REMD simulations. The method is implemented on the basis of new extensions to the REPDSTR module of the biomolecular simulation program CHARMM. As an illustrative example, the absolute binding free energy of p-xylene to the nonpolar cavity of the L99A mutant of T4 lysozyme was calculated. The tests demonstrate that the dual lambda-REMD and H-REMD simulation scheme greatly accelerates the configurational sampling of the rotameric states of the side chains around the binding pocket, thereby improving the convergence of the FEP computations.

Fabrication of polystyrene/gold nanotubes and nanostructure-controlled growth of aluminate.

PubMed

Zhu, Haifeng; Ai, Sufen; He, Qiang; Cui, Yue; Li, Junbai

2007-07-01

Direct adsorption of gold nanoparticles in the inner of alumina template and following immersion of polystyrene (PS) dichloromethane solution in the template resulted in the fabrication of composite nanotubes of PS and gold nanoparticles. Several methods have been used to characterize the tubular structure. Nanostructured sodium aluminates were formed when the anodic alumina oxide membrane was dissolved by the sodium hydroxide. A "flower" shape was found after etching the template while the synthesis process was recorded as function of a time. The results demonstrate that the shape and size of the aluminates nanostructure can be controlled by etching time and the pore diameter of the alumina membrane.

The influence of high temperatures on selected properties of calcium aluminous composites

NASA Astrophysics Data System (ADS)

KoÅáková, Dana; KoÅ¥átková, Jaroslava; Čáchová, Monika; Vejmelková, Eva; Čechmánek, René; Reiterman, Pavel; Černý, Robert

2017-07-01

The article compares different types of aluminate cements with the reference Portland cement, used in refractory composites. The rate of influence of elevated temperatures (400 °C and 1000 °C) is studied. The investigated parameters are basic physical characteristics and mechanical properties. Results show the best behaviour of the mixture containing Portland cement for the reference state (in the means of all studied parameters); which however after exposition to 1000 °C has the worst performance. Both aluminate cements behave better after heating, which proves its suitability for refractory composites. It is concluded, that the mixture with Gorkal cement achieves the best results.

Integrated fountain effect pump device for fluid management at low gravity

NASA Technical Reports Server (NTRS)

Yuan, S. W. K.; Frank, D. J.

1988-01-01

A new device for fluid management at low gravity is described. The system is basically the same as the enclosed capillary device using screens, in which the screens along the gallery channels are replaced by porous plugs which are responsible for both the fluid retention and pumping of He II; in this device, no downstream pump is needed. The plugs in contact with liquid He on both sides act as a fountain-effect pumps (FEPs), while plugs exposed to vapor on one side behave as vapor-liquid phase separators (VLPSs). The total net rate of He II transfer into the receiving tank equals the mass flow rate through the FEP plugs minus the liquid loss from the VLPS plugs. The results of the performance analysis of this integrated FEP device are presented together with its schematic diagram.

Volatilization of PM2.5 Inorganic Ions in a Filter Pack System with Backup Filter and Denuders

NASA Astrophysics Data System (ADS)

Kim, C.; Choi, Y.; Ghim, Y.

2012-12-01

Concentrations of PM2.5 inorganic ions were measured at the rooftop of the 5-story building on the hill (37.02oN, 127.16oE, 167 m above sea level) in the Global Campus of Hankuk University of Foreign Studies, about 35 km southeast of downtown Seoul, Korea. The measurements were made four times during one-year span between 2011 and 2012 by considering the climate of Korea with distinct seasonal variations: July 29 to August 26 (summer); September 14 to October 13 (fall); November 28 to January 4 (winter); February 14 to May 31 (spring). A filter pack system was composed of PM2.5 cyclone, two annular denuders, Teflon filter, nylon filter, and an annular denuder, in series. Two annular denuders were to remove acidic and basic gases prior to collecting particles on the Teflon filter. Nylon filter and an annular denuder were to back up the Teflon filter by absorbing acidic and basic gases, respectively, which were volatilized from collected particles on the Teflon filter. Samplings were made for 24 hours every day. Extracts from filters and denuders were analyzed by ion chromatography to measure concentrations of anions (SO42-, NO3-, Cl-) and cations (Ca2+, Mg2+, NH4+, Na+, K+). The amounts of ionic species absorbed at the backup nylon filter and denuder were examined in terms of meteorological parameters, the amounts of gases removed in front of the Teflon filter, and the amounts of particulate ions collected on the Teflon filter. Major factors to affect the volatilization from particles collected on the Teflon filter were discussed.

Plumbing Fixture for a Microfluidic Cartridge

NASA Technical Reports Server (NTRS)

Francis, Kevin

2007-01-01

A fixture has been devised for making the plumbing connections between a microfluidic device in a replaceable cartridge and an external fluidic system. The fixture includes a 0.25-in. (6.35-mm) thick steel plate, to which the cartridge is fastened by two 10-32 thumb screws. The plate holds one plumbing fitting for the inlet and one for the outlet of the microfluidic device. Each fitting includes a fused-silica tube of 0.006-in. (approx.0.15-mm) inside diameter within a fluorinated ethylene-propylene (FEP) tube of 0.0155-in. (approx.0.39-mm) inside diameter and 0.062- in. (approx.1.57-mm) outside diameter. The FEP tube is press-fit through the steel plate so that its exposed end is flush with the surface of the plate, and the silica tube protrudes 0.03 in. (approx.0.76 mm) from the plate/FEP-tube-end surface. The cartridge includes a glass cover plate that contains 0.06-mm-wide access ports. When the cartridge is fastened to the steel plate, the silica tubes become inserted through the access ports and into the body of the cartridge, while the ends of the FEP tubes become butted against the glass cover plate. An extremely tight seal is thereby made.

The role of intramolecular nonbonded interaction and angle sampling in single-step free energy perturbation

NASA Astrophysics Data System (ADS)

Chiang, Ying-Chih; Pang, Yui Tik; Wang, Yi

2016-12-01

Single-step free energy perturbation (sFEP) has often been proposed as an efficient tool for a quick free energy scan due to its straightforward protocol and the ability to recycle an existing molecular dynamics trajectory for free energy calculations. Although sFEP is expected to fail when the sampling of a system is inefficient, it is often expected to hold for an alchemical transformation between ligands with a moderate difference in their sizes, e.g., transforming a benzene into an ethylbenzene. Yet, exceptions were observed in calculations for anisole and methylaniline, which have similar physical sizes as ethylbenzene. In this study, we show that such exceptions arise from the sampling inefficiency on an unexpected rigid degree of freedom, namely, the bond angle θ. The distributions of θ differ dramatically between two end states of a sFEP calculation, i.e., the conformation of the ligand changes significantly during the alchemical transformation process. Our investigation also reveals the interrelation between the ligand conformation and the intramolecular nonbonded interactions. This knowledge suggests a best combination of the ghost ligand potential and the dual topology setting, which improves the accuracy in a single reference sFEP calculation by bringing down its error from around 5kBT to kBT.

Operating system for a real-time multiprocessor propulsion system simulator

NASA Technical Reports Server (NTRS)

Cole, G. L.

1984-01-01

The success of the Real Time Multiprocessor Operating System (RTMPOS) in the development and evaluation of experimental hardware and software systems for real time interactive simulation of air breathing propulsion systems was evaluated. The Real Time Multiprocessor Operating System (RTMPOS) provides the user with a versatile, interactive means for loading, running, debugging and obtaining results from a multiprocessor based simulator. A front end processor (FEP) serves as the simulator controller and interface between the user and the simulator. These functions are facilitated by the RTMPOS which resides on the FEP. The RTMPOS acts in conjunction with the FEP's manufacturer supplied disk operating system that provides typical utilities like an assembler, linkage editor, text editor, file handling services, etc. Once a simulation is formulated, the RTMPOS provides for engineering level, run time operations such as loading, modifying and specifying computation flow of programs, simulator mode control, data handling and run time monitoring. Run time monitoring is a powerful feature of RTMPOS that allows the user to record all actions taken during a simulation session and to receive advisories from the simulator via the FEP. The RTMPOS is programmed mainly in PASCAL along with some assembly language routines. The RTMPOS software is easily modified to be applicable to hardware from different manufacturers.

A Study of Soft Neurological Signs and Its Correlates in Drug-Naive Patients with First Episode Psychosis.

PubMed

Gunasekaran, Vanishree; Venkatesh, V Mathan Kumar; Asokan, T V

2016-01-01

Soft neurological signs are minor, non localizing, objective abnormalities, thought to reflect damage in cortical and sub-cortical connections or connections within different cortical regions. Regional structural grey matter anomalies have already been observed and correlated with the presence of cognitive deficits and presence of soft neurological signs in schizophrenic patients. Drug naive patients presenting with first episode of psychosis (FEP)were clinically evaluated for soft neurological signs using the Cambridge Neurological Inventory. The soft neurological signs scores were compared with scores in healthy volunteers. In the patient group, this score was also correlated with demographic and disorder variables. Of the 30 patients with FEP, 60% were women. The average age of the participant was 36.2 years. The average duration of illness was 1.55 years. More than 50% of the patients had schizophrenia. 93.3% of patients with FEP had atleast one soft neurological sign compared to 16.6% of controls. The average score on BPRS was 25.86 and on PANSS was 39.29, and BPRS, PANSS scores had a significant correlation with total soft neurological signs score. There is a significantly higher incidence of soft neurological signs in patients with FEP, particularly schizophrenia. The presence of soft signs correlated with the severity of psychosis.

Results from a pilot study of a computer-based role-playing game for young people with psychosis.

PubMed

Olivet, Jeffrey; Haselden, Morgan; Piscitelli, Sarah; Kenney, Rachael; Shulman, Alexander; Medoff, Deborah; Dixon, Lisa

2018-03-15

Recent research on first episode psychosis (FEP) has demonstrated the effectiveness of coordinated specialty care (CSC) models to support young adults and their families, yet few tools exist to promote engagement in care. This study aimed to develop a prototype computer-based role-playing game (RPG) designed for young people who have experienced FEP, and conduct a pilot study to determine feasibility and test whether the game improves consumers' attitudes toward treatment and recovery. Twenty young people with FEP who were receiving services at a CSC program enrolled in the study and played the game for 1 hour. Pre- and post-quantitative assessments measured change in hope, recovery, stigma, empowerment and engagement in treatment. Qualitative interviews explored participants' experience with the game and ideas for further product development. Participants showed significant increase in positive attitudes toward recovery. The qualitative findings further demonstrated the game's positive impact across these domains. Of all game features, participants most highly valued video testimonials of other young adults with FEP telling their stories of hope and recovery. These findings provide modest support for the potential benefits of this type of computer-based RPG, if further developed for individuals experiencing psychosis. © 2018 John Wiley & Sons Australia, Ltd.

Corrosion Chemistry in Inhibited HDA.

DTIC Science & Technology

1980-11-30

mg HF. 200 B.1 Teflon PFA Reactor 201 (xviii) .. .. - i LIST OF MICROGRAPHS Micrograph Follows Page 4.1 A1/HDA x 1,000 80 4.2 A1/0.4 Wt % PF5 x 2,000...Ethylene Propylene copolymer Teflon PTFE Polytetrafluoroethylene Teflon PFA Perfluoroalkoxy fluorocarbon resin Spectroscopy IR (ir) Infra-red UV...fluoroplastic apparatus (to avoid any possible contamination by the reaction products of HF with glass). Iron powder (0.3g) was placed in a PFA screw-cap

Evaluation of the Snap Sampler for Sampling Ground Water Monitoring Wells for VOCs and Explosives

DTIC Science & Technology

2007-08-01

prevent losses due to sorption . The time needed for equilibration will depend on the sampling device (and the materials in the sampler), the physical...bottles contain a perfluoroalkoxy ( PFA ) Teflon-coated spring mechanism that is connected to PFA Teflon end caps at both ends of the bottles...materials: polyvinylidene fluoride (PVDF) Kynar tubing or PFA Teflon tubing. These samplers are deployed in the well with the end caps of the bottle

Nylon and teflon scribe effect on NBR to Chemlok 233 and NBR to NBR bond interfaces

NASA Technical Reports Server (NTRS)

Jensen, S. K.

1990-01-01

A study was requested by Manufacturing Engineering to determine what effects marking with nylon (6/6) and Teflon scribes may have on subsequent bonding. Witness panel bond specimens were fabricated by the development lab to test both acrylonitrile butadiene rubber (NBR) to Chemlok and NBR to NBR after controlled exposure. The nylon rod used as a scribe tool demonstrates virtually no bond deterioration when used to scribe lines on either the Chemlok to NBR surfaces or the NBR to NBR interface. Lab test results indicate that the nylon rod-exposed samples produce tensile and peel values very similar to the control samples and the Teflon exposed samples produce tensile and peel values much lower than the control samples. Visual observation of the failure surfaces of the tested samples shows that Teflon scribing produces an obvious contamination to the surface and the nylon produces no effect. Photographs of test samples are provided. It is concluded that Teflon stock used as a scribe tool on a Chemlok 233 to NBR surface or an NBR to NBR surface has a detrimental effect on the bond integrity on either of these bond interfaces. Therefore, it is recommended that the nylon rod continue to be used where a scribe line is required in the redesigned solid rocket motor segment insulation layup operations. The use of Teflon scribes should not be considered.

Teflon Injection into the Trachea Causes Predictable Fibroblastic Response and Collagen Deposition: A Pilot Study.

PubMed

Longoria, Javier A; Fujiwara, Miwa; Guerra, Catalina; Lee, Jeffrey L; Sassoon, Catherine S H; Mazdisnian, Farhad

2016-10-01

Expiratory central airway collapse is an increasingly recognized abnormality of the central airways and may be present in as many as 22% of patients evaluated for chronic obstructive pulmonary disease and/or asthma. Many current treatment options require invasive procedures that have been shown to cause significant morbidity and mortality. To test the hypothesis that Teflon injection will induce sufficient fibroblast proliferation and collagen deposition, we evaluated the time course on the effect of Teflon injection in the posterior membranous trachea on the histopathology of the tracheobronchial tree. Six Yucatan Pigs were assigned to undergo general anesthesia and injection of 0.3 to 0.5 mL of sterile Teflon paste in 50% glycerin into the posterior membranous tracheal wall. A control pig received an equivalent volume of glycerin. Animals were euthanized in predefined intervals and tracheas were excised and examined under light microscopy for identifying fibroblast proliferation and collagen deposition. Compared with the control pig, the Teflon injection site showed tissue reaction of fibrohistiocytic proliferation and subsequent collagen deposition in all animals. Furthermore, the increased fibroblast proliferation and collagen deposition were time dependent (P<0.01). This pilot study demonstrates histopathologic changes in the trachea after Teflon injection, comprised of increased fibroblast activity and collagen deposition that could be of potential use in creating greater airway rigidity in patients with sever diffuse excessive dynamic airway collapse.

Teflon-wire piston or stainless-steel bucket stapes prosthesis: does it make a difference?

PubMed

Farrior, J B; Temple, A E

1999-04-01

The goal of this study was to determine whether postoperative (implantation of a stapes prosthesis) hearing gain and the amount of air-bone gap overclosure are more improved with the Teflon-wire piston or with the stainless-steel bucket prosthesis. We retrospectively reviewed the outcomes of 82 surgeries that had been performed by the primary author; 41 of these patients had received a Fisch Teflon-wire piston, and 41 had received a Bailey-modified Robinson stainless-steel bucket prosthesis. The mean hearing gain for the patients who received the Teflon-wire piston was 23.3 dB after primary stapes surgery and 20.5 dB after revision surgery. Patients who received the stainless-steel bucket prosthesis experienced a mean hearing gain of 20.7 and 20.3 dB, respectively. Following primary stapes surgery, the air-bone gap overclosure was 4.4 dB with the Teflon-wire piston and 5.2 dB with the stainless-steel bucket prosthesis. There was no statistically significant difference in either hearing gain or air-bone gap overclosure between the two prostheses.

Lithium aluminate/zirconium material useful in the production of tritium

DOEpatents

Cawley, W.E.; Trapp, T.J.

A composition is described useful in the production of tritium in a nuclear reactor. Lithium aluminate particles are dispersed in a matrix of zirconium. Tritium produced by the reactor of neutrons with the lithium are absorbed by the zirconium, thereby decreasing gas pressure within capsules carrying the material.

Lithium aluminate/zirconium material useful in the production of tritium

DOEpatents

Cawley, W.E.; Trapp, T.J.

1984-10-09

A composition is described useful in the production of tritium in a nuclear reactor. Lithium aluminate particles are dispersed in a matrix of zirconium. Tritium produced by the reactor of neutrons with the lithium are absorbed by the zirconium, thereby decreasing gas pressure within capsules carrying the material.

Lithium aluminate/zirconium material useful in the production of tritium

DOEpatents

Cawley, William E.; Trapp, Turner J.

1984-10-09

A composition is described useful in the production of tritium in a nuclear eactor. Lithium aluminate particles are dispersed in a matrix of zirconium. Tritium produced by the reactor of neutrons with the lithium are absorbed by the zirconium, thereby decreasing gas pressure within capsules carrying the material.

Duplex aluminized coatings

NASA Technical Reports Server (NTRS)

Gedwill, M. A.; Grisaffe, S. J. (Inventor)

1975-01-01

The surface of a metallic base system is initially coated with a metallic alloy layer that is ductile and oxidation resistant. An aluminide coating is then applied to the metallic alloy layer. The chemistry of the metallic alloy layer is such that the oxidation resistance of the subsequently aluminized outermost layer is not seriously degraded.

Luminal surface fabrication for cardiovascular prostheses

NASA Technical Reports Server (NTRS)

Deininger, William D. (Inventor); Gabriel, Stephen B. (Inventor)

1988-01-01

A method is provided for forming a mold surface with microscopic upstanding pillars for molding the inside surface of a vascular prostheses (synthetic blood vessel). The mold article is formed from a quantity of Teflon (polytetrafluoroethylene) which has a polished, flat surface on which a gold film has been sputter deposited. A photoresist layer, which cannot adhere directly to Teflon, adheres to the gold. The photoresist is exposed and developed leaving a sputter resistant mask defining the desired pillar locations, and the resulting workpiece is ion etched to form the pillars in the Teflon. A synthetic blood vessel material is cast against the Teflon mold to form blind recesses on the inside of the synthetic blood vessel, with the recesses being of predetermined uniform cross section and present in a predetermined uniform pattern.

Sapphire tube pressure vessel

DOEpatents

Outwater, John O.

2000-01-01

A pressure vessel is provided for observing corrosive fluids at high temperatures and pressures. A transparent Teflon bag contains the corrosive fluid and provides an inert barrier. The Teflon bag is placed within a sapphire tube, which forms a pressure boundary. The tube is received within a pipe including a viewing window. The combination of the Teflon bag, sapphire tube and pipe provides a strong and inert pressure vessel. In an alternative embodiment, tie rods connect together compression fittings at opposite ends of the sapphire tube.

Investigation of Hydrophobic Radomes for Microwave Landing System.

DTIC Science & Technology

1982-11-01

horizontal heating wires on the inside surface, and 2) a slotted waveguide unit (C-band waveguide, about 2 feet in length) covered with a Teflon shrink tube ...AZ) Fiberglass flat 1.5ft x 13ft NE sandwich (EL) Teflon shrink 1 in x 2 ft SW tubing (Field Mon.) 7 (8) Hydrophobic Coating for Antenna Weather...SURFACE PREPARATION 13 24 Mar 󈨖 Conolite Primer: Vellox S-048 Finish: Microfine FSD, 7 coats, sprayed 14 24 Mar 󈨖 Conolite Teflon film, C-TAPE-36

Study of optical properties of cerium ion doped barium aluminate phosphor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lohe, P. P., E-mail: prachiti.lohe2012@gmail.com; Omanwar, S. K.; Bajaj, N. S.

2016-05-06

In the recent years due to their various optical and technological applications aluminate materials have attracted attention of several researchers. When these materials are doped with rare earth ions they show properties favorable for many optical applications such as high quantum efficiencies. These materials are used in various applications such as lamp phosphors, optically and thermoluminescence dosimeter etc Barium aluminate BaAl{sub 2}O{sub 4} doped with Ce is well known long lasting phosphor. This paper reports synthesis of BaAl{sub 2}O{sub 4}: Ce phosphor prepared by a simple combustion synthesis. The samples were characterized for the phase purity, chemical bonds and luminescentmore » properties.« less

Wafer-scale fabrication of glass-FEP-glass microfluidic devices for lipid bilayer experiments.

PubMed

Bomer, Johan G; Prokofyev, Alexander V; van den Berg, Albert; Le Gac, Séverine

2014-12-07

We report a wafer-scale fabrication process for the production of glass-FEP-glass microdevices using UV-curable adhesive (NOA81) as gluing material, which is applied using a novel "spin & roll" approach. Devices are characterized for the uniformity of the gluing layer, presence of glue in the microchannels, and alignment precision. Experiments on lipid bilayers with electrophysiological recordings using a model pore-forming polypeptide are demonstrated.

BRAIN CHOLINESTERASE INHIBITION AND DEPRESSION OF THE PHOTIC AFTER DISCHARGE (PHAD) OF FLASH EVOKED POTENTIALS (FEPS) IN LONG EVANS RATS FOLLOWING ACUTE OR REPEATED EXPOSURES TO A MIXTURE OF CARBARYL AND PROPOXUR.

EPA Science Inventory

Carbaryl and propoxur are N-methyl carbamate pesticides (NMCs) which are part of the EPA’s cumulative risk assessments for NMCs. These NMCs inhibit cholinesterase (ChE) activity and may lead to cholinergic disruption of CNS function. We used decreases in the PhAD of FEPs to indic...

Association between financial strain, social network and five-year recovery from first episode psychosis.

PubMed

Mattsson, Maria; Topor, Alain; Cullberg, Johan; Forsell, Yvonne

2008-12-01

Despite much effort to positively affect long-term outcome in psychosis and schizophrenia many patients are still facing a poor outcome with persistent psychotic symptoms and decline in social functioning. The aim of this study was to examine the relationship between financial strain and social network and five-year outcome of first episode psychosis (FEP). FEP patients were divided into recovered (n = 52) and non-recovered (n = 19). Each person was matched according to age and gender with four persons (n = 284) from a longitudinal population-based study. All persons had answered an extensive questionnaire including social network, quantitative and qualitative, financial strain and mental health. Linear regression analysis showed that both financial strain and social network were associated, and had a unique contribution, to outcome. The results indicate that FEP patients might benefit from interventions that reduce financial strain thus facilitating daily life and cultural and social activities.

Defect controlled magnetism in FeP/graphene/Ni(111)

PubMed Central

Bhandary, Sumanta; Eriksson, Olle; Sanyal, Biplab

2013-01-01

Spin switching of organometallic complexes by ferromagnetic surfaces is an important topic in the area of molecular nanospintronics. Moreover, graphene has been shown as a 2D surface for physisorption of molecular magnets and strain engineering on graphene can tune the spin state of an iron porphyrin (FeP) molecule from S = 1 to S = 2. Our ab initio density functional calculations suggest that a pristine graphene layer placed between a Ni(111) surface and FeP yields an extremely weak exchange interaction between FeP and Ni whereas the introduction of defects in graphene shows a variety of ferromagnetic and antiferromagnetic exchange interactions. Moreover, these defects control the easy axes of magnetization, strengths of magnetic anisotropy energies and spin-dipolar contributions. Our study suggests a new way of manipulating molecular magnetism by defects in graphene and hence has the potential to be explored in designing spin qubits to realize logic operations in molecular nanospintronics. PMID:24296980

Optimization of a Strontium Aluminate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bone, Alexandria N.

2017-08-01

Strontium aluminate with Eu 2+ and Dy 3+ has been at the forefront of emerging applications for storage phosphors since its discovery in 1996. In this study, the emission intensity and luminescence lifetime of SrAl 2O 4: Eu 2+, Dy 3+ were enhanced by partial substitution of Ca 2+ into Sr 2+ sites in the matrix.

Novel mechanism for the modification of Al2O3-based inclusions in ultra-low carbon Al-killed steel considering the effects of magnesium and calcium

NASA Astrophysics Data System (ADS)

Guo, Jing; Cheng, Shu-sen; Guo, Han-jie; Mei, Ya-guang

2018-03-01

Many researchers have explored the inclusion modification mechanism to improve non-metallic inclusion modifications in steelmaking. In this study, two types of industrial trials on inclusion modifications in liquid steel were conducted using ultra-low-carbon Al-killed steel with different Mg and Ca contents to verify the effects of Ca and Mg contents on the modification mechanism of Al2O3-based inclusions during secondary refining. The results showed that Al2O3-based inclusions can be modified into liquid calcium aluminate or a multi-component inclusion with the addition of a suitable amount of Ca. In addition, [Mg] in liquid steel can further reduce CaO in liquid calcium aluminate to drive its evolution into CaO-MgO-Al2O3 multi-component inclusions. Thermodynamic analysis confirmed that the reaction between [Mg] and CaO in liquid calcium aluminate occurs when the MgO content of liquid calcium aluminate is less than 3wt% and the temperature is higher than 1843 K.

Numerical prediction on static and dynamic properties for rotating mirror of ultra-high-speed photography

NASA Astrophysics Data System (ADS)

Huang, Hongbin; Li, Jingzhen; Gong, Xiangdong; Sun, Fengshan; He, Tiefeng

2007-01-01

The methods of numerical analysis for the strength and vibration modals of rotating mirrors were presented based respectively on the three-dimensional elastic mechanics and dynamics. On strength computation, the finite element models of rotating mirror were established according to the real structure of mirror, and the rotating three-faced aluminous and beryllium mirrors were analysed contrastively. Results display that the surface deformation quantity of the aluminous mirror is approximately 20 times as large as beryllium one, and the maximum stress is 1.6 times against the latter. Then, the three-faced aluminous mirrors were analyzed at variedly fit between shaft and axle hole. One conclusion is gotten out that the mirror strength is foreign to fits, but it is weaken by the axle hole obviously. On the modal analysis of vibration, this method can simulates accurately the natural frequencies and corresponding modalities of mirror. And the results from three-face aluminous mirror indicate that the resonance points of a new mirror may be guaranteed existing in selected speed range.

Novel nanostructured oxygen sensor

NASA Astrophysics Data System (ADS)

Boardman, Alan James

New government regulations and industry requirements for medical oxygen sensors require the development of alternate materials and process optimization of primary sensor components. Current oxygen sensors are not compliant with the Restriction of Hazardous Substances (RoHS) Directive. This work focused on two areas. First, was finding suitable readily available materials for the sensor anodes. Second was optimizing the processing of the sensor cathode membrane for reduced delamination. Oxygen sensors were made using tin (Sn) and bismuth (Bi) electrodes, potassium hydroxide (KOH) and acetic acid (CH3COOH) electrolytes with platinum (Pt) and gold (Au) reference electrodes. Bi electrodes were fabricated by casting and pressing processes. Electrochemical characterization of the Sn and Bi electrodes was performed by Cyclic Voltammetry (CV), Electrochemical Impedance Spectroscopy (EIS) and sensing characterization per BSEN ISO 21647:2009 at various oxygen percentages, 0%, 20.9% and 100% oxygen levels with an automated test apparatus. The Sn anode with both electrolyte solutions showed good oxygen sensing properties and performance in a sensor. This system shows promise for replacement of Pb electrodes as required by the RoHS Directive. The Bi anode with Au cathode in both KOH and CH3COOH electrolytes showed acceptable performance and oxygen sensing properties. The Bi anodes fabricated by separate manufacturing methods demonstrated effectiveness for use in medical oxygen sensors. Gold thin films were prepared by magnetron sputtering on Flouroethylene Polymer (FEP) films. The FEP substrate temperature ranged from -77°C to 50°C. X-Ray Diffraction (XRD) and 4-point resistivity characterized the effects of substrate temperature to Au thin film particle size. XRD peak broadening and resistivity measurements showed a strong correlation of particle size to FEP substrate temperature. Particle size at 50°C was 594A and the -77°C particle size was 2.4 x 103A. Substrate temperature exhibited a strong correlation to adhesion of the Au thin film to the FEP. Adhesion of the Au thin film with a FEP temperature of 50°C was rated a 3B per the ASTM D3359-02 peel test standard. At FEP substrate temperature of -77°C it was rated at 1B. The morphology of the deposited Au thin films was observed using optical microscopy and Scanning Electron Microscopy (SEM).

Multiwall carbon nanotube reinforced teflon fibrils for oil spill clean up and its effective recycling as textile dye sorbent.

PubMed

Padmajan Sasikala, Suchithra; Mahesh, K V; Prabhakaran, Prem; Peer Mohammed, A; Ananthakumar, S

2018-04-01

Surface functionalized multiwall carbon nanotube (MWCNT) reinforced teflon fibrils (MWCNT@Teflon) were successfully tested as an - oil - absorbent that can be used as a potential oil recovery material at the time of oil spill accidents in water. We found that oleic acid functionalization of MWCNTs was important for their adhesion onto teflon fibrils and at the same time prevented the MWCNT leaching into oil/water interface. The fibrils had displayed superior mechanical and thermal stability and provided a new insight to oil spill clean-up applications with easy recovery of absorbed oil by simple squeezing. Recycling of exhausted MWCNT@Teflon fibrils after oil recovery applications was conducted by pyrolysis under inert atmosphere in presence of magnetic clay. The magnetic clay absorbed the pyrolysis products, resulting in a heterostructured magnetic clay carbon composite (MCC) which was found super paramagnetic and chemically stable in all pH. The MCC was found capable of adsorbing textile dye from water ultra-fast with in a maximum contact time of 2 min and magnetically separable after adsorption experiments. Copyright © 2018 Elsevier Ltd. All rights reserved.

Electrochemical cell

DOEpatents

Nagy, Z.; Yonco, R.M.; You, H.; Melendres, C.A.

1992-08-25

An electrochemical cell has a layer-type or sandwich configuration with a Teflon center section that houses working, reference and counter electrodes and defines a relatively narrow electrolyte cavity. The center section is surrounded on both sides with thin Teflon membranes. The membranes are pressed in place by a pair of Teflon inner frames which are in turn supported by a pair of outer metal frames. The pair of inner and outer frames are provided with corresponding, appropriately shaped slits that are in plane generally transverse to the plane of the working electrode and permit X-ray beams to enter and exit the cell through the Teflon membranes that cover the slits so that the interface between the working electrode and the electrolyte within the cell may be analyzed by transmission geometry. In one embodiment, the center section consists of two parts, one on top of the other. Alternatively, the center section of the electrochemical cell may consist of two intersliding pieces or may be made of a single piece of Teflon sheet material. The electrolyte cavity is shaped so that the electrochemical cell can be rotated 90[degree] in either direction while maintaining the working and counter electrodes submerged in the electrolyte. 5 figs.

Electrochemical cell

DOEpatents

Nagy, Zoltan; Yonco, Robert M.; You, Hoydoo; Melendres, Carlos A.

1992-01-01

An electrochemical cell has a layer-type or sandwich configuration with a Teflon center section that houses working, reference and counter electrodes and defines a relatively narrow electrolyte cavity. The center section is surrounded on both sides with thin Teflon membranes. The membranes are pressed in place by a pair of Teflon inner frames which are in turn supported by a pair of outer metal frames. The pair of inner and outer frames are provided with corresponding, appropriately shaped slits that are in plane generally transverse to the plane of the working electrode and permit X-ray beams to enter and exit the cell through the Teflon membranes that cover the slits so that the interface between the working electrode and the electrolyte within the cell may be analyzed by transmission geometry. In one embodiment, the center section consists of two parts, one on top of the other. Alternatively, the center section of the electrochemical cell may consist of two intersliding pieces or may be made of a single piece of Teflon sheet material. The electrolyte cavity is shaped so that the electrochemical cell can be rotated 90.degree. in either direction while maintaining the working and counter electrodes submerged in the electrolyte.

Improved Binding Free Energy Predictions from Single-Reference Thermodynamic Integration Augmented with Hamiltonian Replica Exchange

DTIC Science & Technology

2011-08-15

Izmaylov, A. F.; Bloino, J.; Zheng, G.; Sonnenberg, J. L.; Hada, M.; Ehara, M.; Toyota , K.; Fukuda,R.;Hasegawa, J.; Ishida,M.;Nakajima,T.; Honda , Y...limitations that are inherent in the molecular dynamics (MD) methods used in the simulations. Conventional FEP and TI free energy calculations are...with HREX (HREX-SRTI), which achieved convergence of solvation free energies for a challenging case of an amide system where conventional FEP and TI

Prediction of motivational impairment: 12-month follow-up of the randomized-controlled trial on extended early intervention for first-episode psychosis.

PubMed

Chang, W C; Kwong, V W Y; Chan, G H K; Jim, O T T; Lau, E S K; Hui, C L M; Chan, S K W; Lee, E H M; Chen, E Y H

2017-03-01

Amotivation is prevalent in first-episode psychosis (FEP) patients and is a major determinant of functional outcome. Prediction of amotivation in the early stage of psychosis, however, is under-studied. We aimed to prospectively examine predictors of amotivation in FEP patients in a randomized-controlled trial comparing a 1-year extension of early intervention (Extended EI, 3-year EI) with step-down psychiatric care (SC, 2-year EI). One hundred sixty Chinese patents were recruited from a specialized EI program for FEP in Hong Kong after they have completed this 2-year EI service, randomly allocated to Extended EI or SC, and followed up for 12 months. Assessments on premorbid adjustment, onset profiles, baseline symptom severity and treatment characteristics were conducted. Data analysis was based on 156 subjects who completed follow-up assessments. Amotivation at 12-month follow-up was associated with premorbid adjustment, allocated treatment condition, and levels of positive symptoms, disorganization, amotivation, diminished expression (DE) and depression at study intake. Hierarchical multiple regression analysis revealed that Extended EI and lower levels of DE independently predicted better outcome on 12-month amotivation. Our findings indicate a potentially critical therapeutic role of an extended specialized EI on alleviating motivational impairment in FEP patients. The longer-term effect of Extended EI on amotivation merits further investigation. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Suicidality in first episode psychosis is associated with insight and negative beliefs about psychosis.

PubMed

Barrett, Elizabeth A; Sundet, Kjetil; Faerden, Ann; Agartz, Ingrid; Bratlien, Unni; Romm, Kristin Lie; Mork, Erlend; Rossberg, Jan Ivar; Steen, Nils Eiel; Andreassen, Ole A; Melle, Ingrid

2010-11-01

Suicidal behaviour is prevalent in psychotic disorders. Insight has been found to be associated with increased risk for suicidal behaviour, but not consistently. A possible explanation for this is that insight has different consequences for patients depending on their beliefs about psychosis. The present study investigated whether a relationship between insight, negative beliefs about psychosis and suicidality was mediated by depressive symptoms, and if negative beliefs about psychosis moderated the relationship between insight and suicidality in patients with a first episode of psychosis (FEP). One hundred ninety-four FEP-patients were assessed with a clinical interview for diagnosis, symptoms, functioning, substance use, suicidality, insight, and beliefs about psychosis. Nearly 46% of the patients were currently suicidal. Depressive symptoms, having a schizophrenia spectrum disorder, insight, and beliefs about negative outcomes for psychosis were independently associated with current suicidality; contradicting a mediating effect of depressive symptoms. Negative beliefs about psychosis did not moderate the effect of insight on current suicidality. The results indicate that more depressive symptoms, higher insight, and negative beliefs about psychosis increase the risk for suicidality in FEP-patients. The findings imply that monitoring insight should be part of assessing the suicide risk in patients with FEP, and that treating depression and counteracting negative beliefs about psychosis may possibly reduce the risk for suicidality. Copyright © 2010 Elsevier B.V. All rights reserved.

Emotional perception and theory of mind in first episode psychosis: the role of obsessive-compulsive symptomatology.

PubMed

Ntouros, Evangelos; Bozikas, Vasilios P; Andreou, Christina; Kourbetis, Dimitris; Lavrentiadis, Grigoris; Garyfallos, George

2014-12-15

The aim of the present study was to investigate the effects of comorbid obsessive-compulsive symptoms on emotional perception and theory of mind (ToM) in patients with first-episode psychosis. Participants were 65 patients with non-affective first episode psychosis (FEP) and 47 healthy controls. The patient group was divided into two subgroups, those with (FEP+; n=38) and those without obsessive-compulsive symptomatology (FEP-; n=27). Emotion perception and ToM were assessed with the Perception of Social Inference Test. Severity of psychotic and obsessive-compulsive symptoms was assessed with the Positive and Negative Syndrome Scale (PANSS) and the Yale-Brown Obsessive-Compulsive Scale (Y-BOCS), respectively. Deficits in emotion recognition and theory of mind were confirmed in patients with non-affective first-episode psychosis compared to healthy controls. In patients, comorbidity with obsessive-compulsive symptoms was associated with worse performance on certain aspects of social cognition (ToM 2nd order) compared to FEP- patients. Our findings of impaired emotion perception and ToM in patients with first-episode psychosis support the hypothesis that deficits are already present at illness onset. Presence of OCS appears to have further deleterious effects on social cognition, suggesting that these patients may belong to a schizo-obsessive subtype of schizophrenia characterized by more extensive neurobiological impairment. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

The impact of substance use at psychosis onset on First Episode Psychosis course: results from a 1 year follow-up study in Bologna.

PubMed

Tarricone, Ilaria; Boydell, Jane; Panigada, Serena; Allegri, Fabio; Marcacci, Thomas; Minenna, Maria Gabriella; Kokona, Arnisa; Triolo, Federico; Storbini, Viviana; Michetti, Rossella; Morgan, Craig; Di Forti, Marta; Murray, Robin M; Berardi, Domenico

2014-03-01

Substance abuse is a well established risk factor for First-Episode Psychosis (FEP), but its influence on FEP course is less clear. Starting from our baseline observation that substance users were younger than non-users at the psychosis onset, we hypothesized that substance use at baseline could be an independent risk factor for a worse clinical course. An incidence cohort of patients with FEP collected in an 8year period (2002-2009) at the Bologna West Community Mental Health Centers (CMHCs) was assessed at baseline and at 12month follow-up. Drop-out, hospitalizations and service utilization were used as clinical outcomes. Most of the patients were still in contact with CMHC at 12month follow up. Substance users had a significantly higher rate of hospitalizations during the follow-up after adjusting for age, gender and other potential confounders (OR 5.84, 95% CI 2.44-13.97, p≤0.001). This study adds to previous evidence showing the independent effect of substance use on FEP course. The identification of a "potentially modifiable" environmental predictor of the course of the illness such as substance use at psychosis onset allows us to envisage the possibility of ameliorating the course of the illness by managing this factor. Copyright © 2014 Elsevier B.V. All rights reserved.

Childhood symptoms of inattention-hyperactivity predict cannabis use in first episode psychosis.

PubMed

Cassidy, Clifford M; Joober, Ridha; King, Suzanne; Malla, Ashok K

2011-11-01

A history of childhood symptoms of inattention-hyperactivity is often reported in first episode psychosis (FEP) as is cannabis use. In the general population childhood ADHD predicts future cannabis use but the relationship has not been tested in FEP. Parents of patients with a first episode of psychosis (n=75) retrospectively assessed their affected child for symptoms of early-life disorders, namely, attention deficit hyperactivity disorder (ADHD), conduct disorder (CD) and oppositional defiant disorder (ODD) using the Child Behaviour Checklist (CBCL). Assessments were made prospectively of cannabis use over two years following a FEP and of SCID diagnosis of cannabis-use disorder. Childhood hyperactivity-inattention symptoms predicted inability to maintain abstinence from cannabis following treatment (Wald=8.4, p=.004) and lifetime cannabis-use diagnosis (Wald=5.3, p=.022) in a logistic regression controlling for relevant covariates including symptoms of CD and ODD from ages 12 to 18. When the symptom of inattention was considered in place of the hyperactivity-inattention syndrome it predicted cannabis-use diagnosis (Wald=6.4, p=.011) and persistent abstinence from cannabis (Wald=5.3, p=.021). Symptoms of CD and ODD did not predict cannabis use when hyperactivity-inattention symptoms were controlled for. Symptoms of childhood inattention-hyperactivity predict subsequent cannabis use in FEP. Copyright © 2011 Elsevier B.V. All rights reserved.

Identification of the protein folding transition state from molecular dynamics trajectories

NASA Astrophysics Data System (ADS)

Muff, S.; Caflisch, A.

2009-03-01

The rate of protein folding is governed by the transition state so that a detailed characterization of its structure is essential for understanding the folding process. In vitro experiments have provided a coarse-grained description of the folding transition state ensemble (TSE) of small proteins. Atomistic details could be obtained by molecular dynamics (MD) simulations but it is not straightforward to extract the TSE directly from the MD trajectories, even for small peptides. Here, the structures in the TSE are isolated by the cut-based free-energy profile (cFEP) using the network whose nodes and links are configurations sampled by MD and direct transitions among them, respectively. The cFEP is a barrier-preserving projection that does not require arbitrarily chosen progress variables. First, a simple two-dimensional free-energy surface is used to illustrate the successful determination of the TSE by the cFEP approach and to explain the difficulty in defining boundary conditions of the Markov state model for an entropically stabilized free-energy minimum. The cFEP is then used to extract the TSE of a β-sheet peptide with a complex free-energy surface containing multiple basins and an entropic region. In contrast, Markov state models with boundary conditions defined by projected variables and conventional histogram-based free-energy profiles are not able to identify the TSE of the β-sheet peptide.

Rates and predictors of 18-months remission in an epidemiological cohort of 661 patients with first-episode psychosis.

PubMed

Conus, Philippe; Cotton, Sue; Schimmelmann, Benno G; McGorry, Patrick D; Lambert, Martin

2017-09-01

Most first episode psychosis (FEP) outcome studies are based on patient samples enrolled through an informed consent procedure, which may induce important biases. Our aim was to study the 18-month outcome of FEP in an epidemiological sample of patients treated at the Early Psychosis Prevention and Intervention Centre (EPPIC). The files of 661 FEP patients treated for up to 18 months between 1998 and 2000 were assessed. Symptomatic remission was defined as receiving a score ≤3 on the Clinical Global Impressions (CGI) scales, and functional remission as concurrent fulfillment of occupation/employment and independent living. Predictors were analyzed using stepwise logistic regression models. At endpoint, 63% of FEP patients had reached symptomatic remission and 44% functional remission. Duration of untreated psychosis, baseline symptom intensity, time in service and decrease or remission of substance use, predicted both symptomatic and functional outcome. A history of suicide attempt or non-adherence to medication was linked to lower likelihood to reach symptomatic remission while pre-morbid GAF and employment at baseline were linked to functional outcome. The development of early intervention strategies should be pursued, in order both to provide treatment before symptoms reach a high intensity and to maintain social integration. Specific strategies need to promote engagement, facilitate adherence to medication and to create a framework where key issues such as substance abuse co-morbidity can be addressed.

A Study of Soft Neurological Signs and Its Correlates in Drug-Naive Patients with First Episode Psychosis

PubMed Central

Gunasekaran, Vanishree; Venkatesh, V. Mathan Kumar; Asokan, T. V.

2016-01-01

Background: Soft neurological signs are minor, non localizing, objective abnormalities, thought to reflect damage in cortical and sub-cortical connections or connections within different cortical regions. Regional structural grey matter anomalies have already been observed and correlated with the presence of cognitive deficits and presence of soft neurological signs in schizophrenic patients. Materials and Methods: Drug naive patients presenting with first episode of psychosis (FEP)were clinically evaluated for soft neurological signs using the Cambridge Neurological Inventory. The soft neurological signs scores were compared with scores in healthy volunteers. In the patient group, this score was also correlated with demographic and disorder variables. Results: Of the 30 patients with FEP, 60% were women. The average age of the participant was 36.2 years. The average duration of illness was 1.55 years. More than 50% of the patients had schizophrenia. 93.3% of patients with FEP had atleast one soft neurological sign compared to 16.6% of controls. The average score on BPRS was 25.86 and on PANSS was 39.29, and BPRS, PANSS scores had a significant correlation with total soft neurological signs score. Conclusion: There is a significantly higher incidence of soft neurological signs in patients with FEP, particularly schizophrenia. The presence of soft signs correlated with the severity of psychosis. PMID:27833222

Can cognitive insight predict symptom remission in a first episode psychosis cohort?

PubMed

O'Connor, Jennifer A; Ellett, Lyn; Ajnakina, Olesya; Schoeler, Tabea; Kollliakou, Anna; Trotta, Antonella; Wiffen, Benjamin D; Falcone, Aurora M; Di Forti, Marta; Murray, Robin M; Bhattacharyya, Sagnik; David, Anthony S

2017-02-06

The outcome of first episode psychosis (FEP) is highly variable and difficult to predict. Cognitive insight measured at illness onset has previously been found to predict psychopathology 12-months later. The aims of this study were to examine whether the prospective relationship between cognitive insight and symptom severity is evident at four-years following FEP and to examine some psychological correlates of cognitive insight. FEP participants (n = 90) completed the Beck Cognitive Insight Scale (BCIS) at illness onset, and associations between BCIS scores with symptom severity outcomes (4-years after FEP) were assessed. The BCIS scales (self-reflectiveness and self-certainty) were examined as a composite score, and individually compared to other cognitive measures (IQ and jumping to conclusions (JTC) bias). Regression analyses revealed that the cognitive insight composite did not predict 4-year symptom remission in this study while the self-reflection subscale of the BCIS predicted severity of symptoms at 4-years. Self-certainty items of the BCIS were not associated with symptom severity. Significant correlations between the JTC bias, self-certainty and IQ were found, but self-reflection did not correlate with these other cognitive measures. Self-reflective capacity is a more relevant and independent cognitive construct than self-certainty for predicting prospective symptom severity in psychosis. Improving self-reflection may be a useful target for early intervention research.

Measurements of prompt radiation induced conductivity in Teflon (PTFE).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartman, E. Frederick; Zarick, Thomas Andrew; Sheridan, Timothy J.

2013-05-01

We performed measurements of the prompt radiation induced conductivity (RIC) in thin samples of Teflon (PTFE) at the Little Mountain Medusa LINAC facility in Ogden, UT. Three mil (76.2 microns) samples were irradiated with a 0.5 %CE%BCs pulse of 20 MeV electrons, yielding dose rates of 1E9 to 1E11 rad/s. We applied variable potentials up to 2 kV across the samples and measured the prompt conduction current. Details of the experimental apparatus and analysis are reported in this report on prompt RIC in Teflon.

Detonation Chemistry: An Investigation of Fluorine as an Oxidizing Moiety in Explosives

DTIC Science & Technology

1982-07-07

Aluminized Explosives .. .. .... ....... ....... .... 32 Conclusion .. .. ....... ....... ....... .........34 References...heats with a knifeblade heater. A small centrifugal pump circulates water from the jacket through the jacket lid. The thermometric system is a Hewlett...and that the relative flatness of the expansion adiabats for products of aluminized explosives is due to very high vibrational energy (temperature) and

Radon daughter plate-out onto Teflon

NASA Astrophysics Data System (ADS)

Morrison, E. S.; Frels, T.; Miller, E. H.; Schnee, R. W.; Street, J.

2018-01-01

Radiopure materials for detector components in rare event searches may be contaminated after manufacturing with long-lived 210Pb produced by the decay of atmospheric radon. Charged radon daughters deposited on the surface or implanted in the bulk of detector materials have the potential to cause noticeable backgrounds within dark matter regions of interest. Understanding the mechanics governing these background signals is therefore a paramount concern in dark matter experiments in order to distinguish a real signal from internal detector backgrounds. Teflon (i.e. PTFE) is a specific material of interest because it makes up the walls of the inner detector of many liquid noble detectors such as the LUX-ZEPLIN experiment. The rate of radon daughter plate-out onto Teflon can be orders of magnitude larger than the plate-out rate onto other materials. Mitigation of plate-out onto Teflon and steel by proximity to other materials is demonstrated.

Teflon/SiO₂ Bilayer Passivation for Improving the Electrical Reliability of Oxide TFTs Fabricated Using a New Two-Photomask Self-Alignment Process.

PubMed

Fan, Ching-Lin; Shang, Ming-Chi; Li, Bo-Jyun; Lin, Yu-Zuo; Wang, Shea-Jue; Lee, Win-Der; Hung, Bohr-Ran

2015-04-13

This study proposes a two-photomask process for fabricating amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFTs) that exhibit a self-aligned structure. The fabricated TFTs, which lack etching-stop (ES) layers, have undamaged a-IGZO active layers that facilitate superior performance. In addition, we demonstrate a bilayer passivation method that uses a polytetrafluoroethylene (Teflon) and SiO₂ combination layer for improving the electrical reliability of the fabricated TFTs. Teflon was deposited as a buffer layer through thermal evaporation. The Teflon layer exhibited favorable compatibility with the underlying IGZO channel layer and effectively protected the a-IGZO TFTs from plasma damage during SiO₂ deposition, resulting in a negligible initial performance drop in the a-IGZO TFTs. Compared with passivation-free a-IGZO TFTs, passivated TFTs exhibited superior stability even after 168 h of aging under ambient air at 95% relative humidity.

Evaluation program for secondary spacecraft cells. Initial evaluation tests of General Electric Company standard and teflonated negative electrode 20.0 ampere-hour, nickel-cadmium spacecraft cells with auxiliary electrodes

NASA Technical Reports Server (NTRS)

1974-01-01

The standard plate cells exhibited higher average end-of-charge (EOC) voltages than the cells with teflonated negative plates; they also delivered a higher capacity output in ampere hours following these charges. All the cells reached a pressure of 20 psia before reaching the voltage limit of 1.550 volts during the pressure versus capacity test. The average ampere hours in and voltages at this pressure were 33.6 and 1.505 volts respectively for the teflonated negative plate cells and 35.5 and 1.523 volts for the standard plate cells. All cells exhibited pressure decay in the range of 1 to 7 psia during the last 30 minutes of the 1-hour open circuit stand. Average capacity out for the teflonated and standard negative plate cells was 29.4 and 29.9 ampere hours respectively.

Neutron Monitor Observations and Space Weather, 1. Automatically Search of Great Solar Energetic Particle Event Beginning.

NASA Astrophysics Data System (ADS)

Dorman, L. I.; Pustil'Nik, L. A.; Sternlieb, A.; Zukerman, I. G.

It is well known that in periods of great SEP fluxes of energetic particles can be so big that memory of computers and other electronics in space may be destroyed, satellites and spacecrafts became dead: according to NOAA Space Weather Scales are danger- ous Solar Radiation Storms S5-extreme (flux level of particles with energy > 10 MeV more than 10^5), S4-severe (flux more than 10^4) and S3-strong (flux more than 10^3). In these periods is necessary to switch off some part of electronics for few hours to protect computer memories. These periods are also dangerous for astronauts on space- ships, and passengers and crew in commercial jets (especially during S5 storms). The problem is how to forecast exactly these dangerous phenomena. We show that exact forecast can be made by using high-energy particles (few GeV/nucleon and higher) which transportation from the Sun is characterized by much bigger diffusion coeffi- cient than for small and middle energy particles. Therefore high energy particles came from the Sun much more early (8-20 minutes after acceleration and escaping into so- lar wind) than main part of smaller energy particles caused dangerous situation for electronics (about 30-60 minutes later). We describe here principles and experience of automatically working of program "FEP-Search". The positive result which shows the exact beginning of FEP event on the Emilio Segre' Observatory (2025 m above sea level, Rc=10.8 GV), is determined now automatically by simultaneously increas- ing on 2.5 St. Dev. in two sections of neutron supermonitor. The next 1-min data the program "FEP-Search" uses for checking that the observed increase reflects the begin- ning of real great FEP or not. If yes, automatically starts to work on line the programs "FEP-Research".

Differences in Facial Emotion Recognition between First Episode Psychosis, Borderline Personality Disorder and Healthy Controls

PubMed Central

Gonzalez de Artaza, Maider; Bustamante, Sonia; Orgaz, Pablo; Osa, Luis; Angosto, Virxinia; Valverde, Cristina; Bilbao, Amaia; Madrazo, Arantza; van Os, Jim; Gonzalez-Torres, Miguel Angel

2016-01-01

Background Facial emotion recognition (FER) is essential to guide social functioning and behaviour for interpersonal communication. FER may be altered in severe mental illness such as in psychosis and in borderline personality disorder patients. However, it is unclear if these FER alterations are specifically related to psychosis. Awareness of FER alterations may be useful in clinical settings to improve treatment strategies. The aim of our study was to examine FER in patients with severe mental disorder and their relation with psychotic symptomatology. Materials and Methods Socio-demographic and clinical variables were collected. Alterations on emotion recognition were assessed in 3 groups: patients with first episode psychosis (FEP) (n = 64), borderline personality patients (BPD) (n = 37) and healthy controls (n = 137), using the Degraded Facial Affect Recognition Task. The Positive and Negative Syndrome Scale, Structured Interview for Schizotypy Revised and Community Assessment of Psychic Experiences scales were used to assess positive psychotic symptoms. WAIS III subtests were used to assess IQ. Results Kruskal-Wallis analysis showed a significant difference between groups on the FER of neutral faces score between FEP, BPD patients and controls and between FEP patients and controls in angry face recognition. No significant differences were found between groups in the fear or happy conditions. There was a significant difference between groups in the attribution of negative emotion to happy faces. BPD and FEP groups had a much higher tendency to recognize happy faces as negatives. There was no association with the different symptom domains in either group. Conclusions FEP and BPD patients have problems in recognizing neutral faces more frequently than controls. Moreover, patients tend to over-report negative emotions in recognition of happy faces. Although no relation between psychotic symptoms and FER alterations was found, these deficits could contribute to a patient’s misinterpretations in daily life. PMID:27467692

The SYSGEN user package

NASA Technical Reports Server (NTRS)

Carlson, C. R.

1981-01-01

The user documentation of the SYSGEN model and its links with other simulations is described. The SYSGEN is a production costing and reliability model of electric utility systems. Hydroelectric, storage, and time dependent generating units are modeled in addition to conventional generating plants. Input variables, modeling options, output variables, and reports formats are explained. SYSGEN also can be run interactively by using a program called FEPS (Front End Program for SYSGEN). A format for SYSGEN input variables which is designed for use with FEPS is presented.

Effect of aluminizing of Cr-containing ferritic alloys on the seal strength of a novel high-temperature solid oxide fuel cell sealing glass

NASA Astrophysics Data System (ADS)

Chou, Yeong-Shyung; Stevenson, Jeffry W.; Singh, Prabhakar

A novel high-temperature alkaline earth silicate sealing glass was developed for solid oxide fuel cell (SOFC) applications. The glass was used to join two metallic coupons of Cr-containing ferritic stainless steel for seal strength evaluation. In previous work, SrCrO 4 was found to form along the glass/steel interface, which led to severe strength degradation. In the present study, aluminization of the steel surface was investigated as a remedy to minimize or prevent the strontium chromate formation. Three different processes for aluminization were evaluated with Crofer22APU stainless steel: pack cementation, vapor-phase deposition, and aerosol spraying. It was found that pack cementation resulted in a rough surface with occasional cracks in the Al-diffused region. Vapor-phase deposition yielded a smoother surface, but the resulting high Al content increased the coefficient of thermal expansion (CTE), resulting in the failure of joined coupons. Aerosol spraying of an Al-containing salt resulted in the formation of a thin aluminum oxide layer without any surface damage. The room temperature seal strength was evaluated in the as-fired state and in environmentally aged conditions. In contrast to earlier results with uncoated Crofer22APU, the aluminized samples showed no strength degradation even for samples aged in air. Interfacial and chemical compatibility was also investigated. The results showed aluminization to be a viable candidate approach to minimize undesirable chromate formation between alkaline earth silicate sealing glass and Cr-containing interconnect alloys for SOFC applications.

Charge division in a small proportional chamber constructed with aluminized mylar tubes

NASA Astrophysics Data System (ADS)

Biino, C.; Mussa, R.; Palestini, S.; Pastrone, N.; Pesando, L.

1988-09-01

A tracking detector composed of aluminized mylar drift tubes is under development for the Fermilab experiment 760. A prototype chamber has been constructed. Results on the longitudinal coordinate determined by charge division are given. Spatial resolution values below 2 mm (rms) were found, corresponding to <1% of the chamber length. Results on chamber ageing are also discussed.

High Temperature Oxidation of Hot-Dip Aluminized T92 Steels

NASA Astrophysics Data System (ADS)

Abro, Muhammad Ali; Hahn, Junhee; Lee, Dong Bok

2018-03-01

The T92 steel plate was hot-dip aluminized, and oxidized in order to characterize the high-temperature oxidation behavior of hot-dip aluminized T92 steel. The coating consisted of Al-rich topcoat with scattered Al3Fe grains, Al3Fe-rich upper alloy layer with scattered (Al, Al5Fe2, AlFe)-grains, and Al5Fe2-rich lower alloy layer with scattered (Al5Fe2, AlFe)-grains. Oxidation at 800 °C for 20 h formed (α-Al2O3 scale)/(AlFe layer)/(AlFe3 layer)/(α-Fe(Al) layer), while oxidation at 900 °C for 20 h formed (α-Al2O3 scale plus some Fe2O3)/(AlFe layer)/(AlFe3 layer)/(α-Fe(Al) layer) from the surface. During oxidation, outward migration of all substrate elements, inward diffusion of oxygen, and back and forth diffusion of Al occurred according to concentration gradients. Also, diffusion transformed and broadened AlFe and AlFe3 layers dissolved with some oxygen and substrate alloying elements. Hot-dip aluminizing improved the high-temperature oxidation resistance of T92 steel through preferential oxidation of Al at the surface.

High Temperature Oxidation of Hot-Dip Aluminized T92 Steels

NASA Astrophysics Data System (ADS)

Abro, Muhammad Ali; Hahn, Junhee; Lee, Dong Bok

2018-05-01

The T92 steel plate was hot-dip aluminized, and oxidized in order to characterize the high-temperature oxidation behavior of hot-dip aluminized T92 steel. The coating consisted of Al-rich topcoat with scattered Al3Fe grains, Al3Fe-rich upper alloy layer with scattered (Al, Al5Fe2, AlFe)-grains, and Al5Fe2-rich lower alloy layer with scattered (Al5Fe2, AlFe)-grains. Oxidation at 800 °C for 20 h formed (α-Al2O3 scale)/(AlFe layer)/(AlFe3 layer)/(α-Fe(Al) layer), while oxidation at 900 °C for 20 h formed (α-Al2O3 scale plus some Fe2O3)/(AlFe layer)/(AlFe3 layer)/(α-Fe(Al) layer) from the surface. During oxidation, outward migration of all substrate elements, inward diffusion of oxygen, and back and forth diffusion of Al occurred according to concentration gradients. Also, diffusion transformed and broadened AlFe and AlFe3 layers dissolved with some oxygen and substrate alloying elements. Hot-dip aluminizing improved the high-temperature oxidation resistance of T92 steel through preferential oxidation of Al at the surface.

BLENDED CALCIUM ALUMINATE-CALCIUM SULFATE CEMENT-BASED GROUT FOR P-REACTOR VESSEL IN-SITU DECOMMISSIONING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Langton, C.; Stefanko, D.

2011-03-10

The objective of this report is to document laboratory testing of blended calcium aluminate - calcium hemihydrate grouts for P-Reactor vessel in-situ decommissioning. Blended calcium aluminate - calcium hemihydrate cement-based grout was identified as candidate material for filling (physically stabilizing) the 105-P Reactor vessel (RV) because it is less alkaline than portland cement-based grout which has a pH greater than 12.4. In addition, blended calcium aluminate - calcium hemihydrate cement compositions can be formulated such that the primary cementitious phase is a stable crystalline material. A less alkaline material (pH {<=} 10.5) was desired to address a potential materials compatibilitymore » issue caused by corrosion of aluminum metal in highly alkaline environments such as that encountered in portland cement grouts [Wiersma, 2009a and b, Wiersma, 2010, and Serrato and Langton, 2010]. Information concerning access points into the P-Reactor vessel and amount of aluminum metal in the vessel is provided elsewhere [Griffin, 2010, Stefanko, 2009 and Wiersma, 2009 and 2010, Bobbitt, 2010, respectively]. Radiolysis calculations are also provided in a separate document [Reyes-Jimenez, 2010].« less

Experimental validation of a numerical model predicting the charging characteristics of Teflon and Kapton under electron beam irradiation

NASA Technical Reports Server (NTRS)

Hazelton, R. C.; Yadlowsky, E. J.; Churchill, R. J.; Parker, L. W.; Sellers, B.

1981-01-01

The effect differential charging of spacecraft thermal control surfaces is assessed by studying the dynamics of the charging process. A program to experimentally validate a computer model of the charging process was established. Time resolved measurements of the surface potential were obtained for samples of Kapton and Teflon irradiated with a monoenergetic electron beam. Results indicate that the computer model and experimental measurements agree well and that for Teflon, secondary emission is the governing factor. Experimental data indicate that bulk conductivities play a significant role in the charging of Kapton.

Production of biologically inert Teflon thin layers on the surface of allergenic metal objects by pulsed laser deposition technology

NASA Astrophysics Data System (ADS)

Hopp, B.; Smausz, T.; Kresz, N.; Nagy, P. M.; Juhász, A.; Ignácz, F.; Márton, Z.

Allergic-type diseases are current nowadays, and they are frequently caused by certain metals. We demonstrated that the metal objects can be covered by Teflon protective thin layers using a pulsed laser deposition procedure. An ArF excimer laser beam was focused onto the surface of pressed PTFE powder pellets; the applied fluences were 7.5-7.7 J/cm2. Teflon films were deposited on fourteen-carat gold, silver and titanium plates. The number of ablating pulses was 10000. Post-annealing of the films was carried out in atmospheric air at oven temperatures between 320 and 500 °C. The thickness of the thin layers was around 5 μm. The prepared films were granular without heat treatment or after annealing at a temperature below 340 °C. At 360 °C a crystalline, contiguous, smooth, very compact and pinhole-free thin layer was produced; a melted and re-solidified morphology was observed above 420 °C. The adhesion strength between the Teflon films and the metal substrates was determined. This could exceed 1-4 MPa depending on the treatment temperature. It was proved that the prepared Teflon layers can be suitable for prevention of contact between the human body and allergen metals and so for avoidance of metal allergy.

Flexible Teflon nanocone array surfaces with tunable superhydrophobicity for self-cleaning and aqueous droplet patterning.

PubMed

Toma, Mana; Loget, Gabriel; Corn, Robert M

2014-07-23

Tunable hydrophobic/hydrophilic flexible Teflon nanocone array surfaces were fabricated over large areas (cm(2)) by a simple two-step method involving the oxygen plasma etching of a colloidal monolayer of polystyrene beads on a Teflon film. The wettability of the nanocone array surfaces was controlled by the nanocone array dimensions and various additional surface modifications. The resultant Teflon nanocone array surfaces were hydrophobic and adhesive (a "gecko" type of surface on which a water droplet has a high contact angle but stays in place) with a contact angle that correlated with the aspect ratio/sharpness of the nanocones. The surfaces switched to a superhydrophobic or "lotus" type of surface when hierarchical nanostructures were created on Teflon nanocones by modifying them with a gold nanoparticle (AuNPs) film. The nanocone array surfaces could be made superhydrophobic with a maximum contact angle of 160° by the further modification of the AuNPs with an octadecanethiol (C18SH) monolayer. Additionally, these nanocone array surfaces became hydrophilic when the nanocone surfaces were sequentially modified with AuNPs and hydrophilic polydopamine (PDA) layers. The nanocone array surfaces were tested for two potential applications: self-cleaning superhydrophobic surfaces and for the passive dispensing of aqueous droplets onto hybrid superhydrophobic/hydrophilic microarrays.

Doppler ultrasound compatible plastic material for use in rigid flow models.

PubMed

Wong, Emily Y; Thorne, Meghan L; Nikolov, Hristo N; Poepping, Tamie L; Holdsworth, David W

2008-11-01

A technique for the rapid but accurate fabrication of multiple flow phantoms with variations in vascular geometry would be desirable in the investigation of carotid atherosclerosis. This study demonstrates the feasibility and efficacy of implementing numerically controlled direct-machining of vascular geometries into Doppler ultrasound (DUS)-compatible plastic for the easy fabrication of DUS flow phantoms. Candidate plastics were tested for longitudinal speed of sound (SoS) and acoustic attenuation at the diagnostic frequency of 5 MHz. Teflon was found to have the most appropriate SoS (1376 +/- 40 m s(-1) compared with 1540 m s(-1) in soft tissue) and thus was selected to construct a carotid bifurcation flow model with moderate eccentric stenosis. The vessel geometry was machined directly into Teflon using a numerically controlled milling technique. Geometric accuracy of the phantom lumen was verified using nondestructive micro-computed tomography. Although Teflon displayed a higher attenuation coefficient than other tested materials, Doppler data acquired in the Teflon flow model indicated that sufficient signal power was delivered throughout the depth of the vessel and provided comparable velocity profiles to that obtained in the tissue-mimicking phantom. Our results indicate that Teflon provides the best combination of machinability and DUS compatibility, making it an appropriate choice for the fabrication of rigid DUS flow models using a direct-machining method.

Fast surface temperature measurement of Teflon propellant-in-pulsed ablative discharges using HgCdTe photovoltaic cells

NASA Astrophysics Data System (ADS)

Antonsen, Erik L.; Burton, Rodney L.; Reed, Garrett A.; Spanjers, Gregory G.

2006-10-01

High-speed mercury cadmium telluride photovoltaic detectors, sensitive to infrared emission, are investigated as a means of measuring surface temperature on a microsecond time frame during pulsed ablative discharges with Teflon™ as the ablated material. Analysis is used to derive a governing equation for detector output voltage for materials with wavelength dependent emissivity. The detector output voltage is experimentally calibrated against thermocouples embedded in heated Teflon. Experimental calibration is performed with Teflon that has been exposed to ˜200 pulsed discharges and non-plasma-exposed Teflon and is compared to theoretical predictions to analyze emissivity differences. The diagnostic capability is evaluated with measurements of surface temperature from the Teflon propellant of electric micropulsed plasma thrusters. During the pulsed current discharge, there is insufficient information to claim that the surface temperature is accurately measured. However, immediately following the discharge, the postpulse cooling curve is measured. The statistical spread of postpulse surface temperature from shot to shot, most likely due to arc constriction and localization, is investigated to determine an operational envelope for postpulse temperature and mass ablation. This information is useful for determining postpulse ablation contributions to mass loss as well as evaluation of theoretical discharge models currently under development.

Europa Propulsion Valve Seat Material Testing

NASA Technical Reports Server (NTRS)

Addona, Brad M.

2017-01-01

The Europa mission and spacecraft design presented unique challenges for selection of valve seat materials that met the fluid compatibility requirements, and combined fluid compatibility and high radiation exposure level requirements. The Europa spacecraft pressurization system valves will be exposed to fully saturated propellant vapor for the duration of the mission. The effects of Nitrogen Tetroxide (NTO) and Monomethylhydrazine (MMH) propellant vapors on heritage valve seat materials, such as Vespel SP-1 and Polychlorotrifluoroethylene (PCTFE), were evaluated to determine if an alternate material is required. In liquid system applications, Teflon is the only available compatible valve seat material. Radiation exposure data for Teflon in an air or vacuum environment has been previously documented. Radiation exposure data for Teflon in an oxidizer environment such as NTO, was not available, and it was unknown whether the effects would be similar to those on air-exposed samples. Material testing was conducted by Marshall Space Flight Center (MSFC) and White Sands Test Facility (WSTF) to determine the effects of propellant vapor on heritage seat materials for pressurization valve applications, and the effects of combined radiation and NTO propellant exposure on Teflon. The results indicated that changes in heritage pressurization valve seat materials' properties rendered them unsuitable for the Europa application. The combined radiation and NTO exposure testing of Teflon produced results equivalent to combined radiation and air exposure results.

Application of Free Energy Perturbation for the Design of BACE1 Inhibitors.

PubMed

Ciordia, Myriam; Pérez-Benito, Laura; Delgado, Francisca; Trabanco, Andrés A; Tresadern, Gary

2016-09-26

Novel spiroaminodihydropyrroles probing for optimized interactions at the P3 pocket of β-secretase 1 (BACE1) were designed with the use of free energy perturbation (FEP) calculations. The resulting molecules showed pIC50 potencies in enzymatic BACE1 inhibition assays ranging from approximately 5 to 7. Good correlation was observed between the predicted activity from the FEP calculations and experimental activity. Simulations run with a default 5 ns approach delivered a mean unsigned error (MUE) between prediction and experiment of 0.58 and 0.91 kcal/mol for retrospective and prospective applications, respectively. With longer simulations of 10 and 20 ns, the MUE was in both cases 0.57 kcal/mol for the retrospective application, and 0.69 and 0.59 kcal/mol for the prospective application. Other considerations that impact the quality of the calculations are discussed. This work provides an example of the value of FEP as a computational tool for drug discovery.

Comparative study between REAP 200 and FEP171 CAR with 50-kV raster e-beam system for sub-100-nm technology

NASA Astrophysics Data System (ADS)

Baik, Ki-Ho; Lem, Homer Y.; Dean, Robert L.; Osborne, Stephen; Mueller, Mark; Abboud, Frank E.

2003-08-01

In this paper, a process established with a positive-tone chemically amplified resist (CAR) from TOK REAP200 and Fujifilm Arch FEP171 and 50kV MEBES system is discussed. This TOK resist is developed for raster scan 50 kV e-beam systems. It has high contrast, good coating characteristics, good dry etch selectivity, and high environmental stability. In the mask industries, the most popular positive tone CAR is FEP171, which is a high activation energy type CAR. REAP (Raster E-beam Advanced Process) 200 is low activation energy type and new acetal protecting polymer. In this study, we compared to these different type resists in terms of contrast, PAB and PEB latitude, resist profile, footing, T-topping, PED stability, LER, Global CDU (Critical Dimension Uniformity) and resolution. The REAP200 Resist obtained 75nm isolated lines and spaces, 90nm dense patterns with vertical profile, and a good stability of delay time.

Self-Cleaning Microcavity Array for Photovoltaic Modules.

PubMed

Vüllers, Felix; Fritz, Benjamin; Roslizar, Aiman; Striegel, Andreas; Guttmann, Markus; Richards, Bryce S; Hölscher, Hendrik; Gomard, Guillaume; Klampaftis, Efthymios; Kavalenka, Maryna N

2018-01-24

Development of self-cleaning coatings is of great interest for the photovoltaic (PV) industry, as soiling of the modules can significantly reduce their electrical output and increase operational costs. We fabricated flexible polymeric films with novel disordered microcavity array (MCA) topography from fluorinated ethylene propylene (FEP) by hot embossing. Because of their superhydrophobicity with water contact angles above 150° and roll-off angles below 5°, the films possess self-cleaning properties over a wide range of tilt angles, starting at 10°, and contaminant sizes (30-900 μm). Droplets that impact the FEP MCA surface with velocities of the same order of magnitude as that of rain bounce off the surface without impairing its wetting properties. Additionally, the disordered MCA topography of the films enhances the performance of PV devices by improving light incoupling. Optical coupling of the FEP MCA films to a glass-encapsulated multicrystalline silicon solar cell results in 4.6% enhancement of the electrical output compared to that of an uncoated device.

Characterization of external potential for field emission resonances and its applications on nanometer-scale measurements

NASA Astrophysics Data System (ADS)

Lu, Shin-Ming; Chan, Wen-Yuan; Su, Wei-Bin; Pai, Woei Wu; Liu, Hsiang-Lin; Chang, Chia-Seng

2018-04-01

The form of the external potential (FEP) for generating field emission resonance (FER) in a scanning tunneling microscopy (STM) junction is usually assumed to be triangular. We demonstrate that this assumption can be examined using a plot that can characterize FEP. The plot is FER energies versus the corresponding distances between the tip and sample. Through this energy–distance relationship, we discover that the FEP is nearly triangular for a blunt STM tip. However, the assumption of a triangular potential form is invalid for a sharp tip. The disparity becomes more severe as the tip is sharper. We demonstrate that the energy–distance plot can be exploited to determine the barrier width in field emission and estimate the effective sharpness of an STM tip. Because FERs were observed on Pb islands grown on the Cu(111) surface in this study, determination of the tip sharpness enabled the derivation of the subtle expansion deformation of Pb islands due to electrostatic force in the STM junction.

Determination of performance of non-ideal aluminized explosives.

PubMed

Keshavarz, Mohammad Hossein; Mofrad, Reza Teimuri; Poor, Karim Esmail; Shokrollahi, Arash; Zali, Abbas; Yousefi, Mohammad Hassan

2006-09-01

Non-ideal explosives can have Chapman-Jouguet (C-J) detonation pressure significantly different from those expected from existing thermodynamic computer codes, which usually allows finding the parameters of ideal detonation of individual high explosives with good accuracy. A simple method is introduced by which detonation pressure of non-ideal aluminized explosives with general formula C(a)H(b)N(c)O(d)Al(e) can be predicted only from a, b, c, d and e at any loading density without using any assumed detonation products and experimental data. Calculated detonation pressures show good agreement with experimental values with respect to computed results obtained by complicated computer code. It is shown here how loading density and atomic composition can be integrated into an empirical formula for predicting detonation pressure of proposed aluminized explosives.

Synthesis of nano grade hollow silica sphere via a soft template method.

PubMed

Tsai, Ming-Shyong; Li, Miao Ju; Yen, Fu-Hsu

2008-06-01

The nano grade hollow silica sphere (HSS) was synthesized by a novel soft template method. We found that the precipitate of aluminate had a porous structure that could be the soft template for HSS. After mixing the colloidal silica with the aluminate precipitate, the bubble trapped in this porous structure could form the nano grade HSS. The aluminate precipitate was removed by adjusting the pH of the slurry to approximately 1. The outside diameter, the specific surface, and the mean pore size diameter of the forming HSS were 60-90 nm, 571 m2/g, and 3 nm, respectively. The formed HSS was collected by modifying the surface with Si(OCH3)3CHCH2 (VTMO) and then filtrating the precipitated gel in the n-butanol and ethanol solvent system.

Validation of tautomeric and protomeric binding modes by free energy calculations. A case study for the structure based optimization of D-amino acid oxidase inhibitors.

PubMed

Orgován, Zoltán; Ferenczy, György G; Steinbrecher, Thomas; Szilágyi, Bence; Bajusz, Dávid; Keserű, György M

2018-02-01

Optimization of fragment size D-amino acid oxidase (DAAO) inhibitors was investigated using a combination of computational and experimental methods. Retrospective free energy perturbation (FEP) calculations were performed for benzo[d]isoxazole derivatives, a series of known inhibitors with two potential binding modes derived from X-ray structures of other DAAO inhibitors. The good agreement between experimental and computed binding free energies in only one of the hypothesized binding modes strongly support this bioactive conformation. Then, a series of 1-H-indazol-3-ol derivatives formerly not described as DAAO inhibitors was investigated. Binding geometries could be reliably identified by structural similarity to benzo[d]isoxazole and other well characterized series and FEP calculations were performed for several tautomers of the deprotonated and protonated compounds since all these forms are potentially present owing to the experimental pKa values of representative compounds in the series. Deprotonated compounds are proposed to be the most important bound species owing to the significantly better agreement between their calculated and measured affinities compared to the protonated forms. FEP calculations were also used for the prediction of the affinities of compounds not previously tested as DAAO inhibitors and for a comparative structure-activity relationship study of the benzo[d]isoxazole and indazole series. Selected indazole derivatives were synthesized and their measured binding affinity towards DAAO was in good agreement with FEP predictions.

Virtual substitution scan via single-step free energy perturbation.

PubMed

Chiang, Ying-Chih; Wang, Yi

2016-02-05

With the rapid expansion of our computing power, molecular dynamics (MD) simulations ranging from hundreds of nanoseconds to microseconds or even milliseconds have become increasingly common. The majority of these long trajectories are obtained from plain (vanilla) MD simulations, where no enhanced sampling or free energy calculation method is employed. To promote the 'recycling' of these trajectories, we developed the Virtual Substitution Scan (VSS) toolkit as a plugin of the open-source visualization and analysis software VMD. Based on the single-step free energy perturbation (sFEP) method, VSS enables the user to post-process a vanilla MD trajectory for a fast free energy scan of substituting aryl hydrogens by small functional groups. Dihedrals of the functional groups are sampled explicitly in VSS, which improves the performance of the calculation and is found particularly important for certain groups. As a proof-of-concept demonstration, we employ VSS to compute the solvation free energy change upon substituting the hydrogen of a benzene molecule by 12 small functional groups frequently considered in lead optimization. Additionally, VSS is used to compute the relative binding free energy of four selected ligands of the T4 lysozyme. Overall, the computational cost of VSS is only a fraction of the corresponding multi-step FEP (mFEP) calculation, while its results agree reasonably well with those of mFEP, indicating that VSS offers a promising tool for rapid free energy scan of small functional group substitutions. This article is protected by copyright. All rights reserved. © 2016 Wiley Periodicals, Inc.

Peripheral endocannabinoid system dysregulation in first-episode psychosis.

PubMed

Bioque, Miquel; García-Bueno, Borja; Macdowell, Karina S; Meseguer, Ana; Saiz, Pilar A; Parellada, Mara; Gonzalez-Pinto, Ana; Rodriguez-Jimenez, Roberto; Lobo, Antonio; Leza, Juan C; Bernardo, Miguel

2013-12-01

Several hypotheses involving alterations of the immune system have been proposed among etiological explanations for psychotic disorders. The endocannabinoid system (ECS) has a homeostatic role as an endogenous neuroprotective and anti-inflammatory system. Alterations of this system have been associated with psychosis. Cannabis use is a robust risk factor for these disorders that could alter the ECS signalling. In this study, 95 patients with a first episode of psychosis (FEP) and 90 healthy controls were recruited. Protein expression of cannabinoid receptor 2 (CB2), the protein levels of the main endocannabinoid synthesizing enzymes N-acyl phosphatidylethanolamine phospholipase (NAPE) and diacylglycerol lipase (DAGL), and of degradation enzymes fatty acid amide hydrolase (FAAH) and monoacylglycerol lipase (MAGL) were determined by western blot analysis in peripheral blood mononuclear cells (PBMCs). Patients with a FEP showed a decreased expression of CB2 and of both endocannabinoids synthesizing enzymes (NAPE and DAGL) in comparison to healthy controls. After controlling for age, gender, body mass index, and cannabis use, NAPE and DAGL expression remained significantly decreased, whereas FAAH and MAGL expression were increased. On the other hand, FEP subjects with history of severe cannabis use showed a larger ECS dysregulation compared with healthy controls. These results indicate an ECS dysregulation in PBMC of FEP patients. The alteration of the ECS presented at the initial phases of psychosis could be contributing to the pathophysiology of the disease and constitutes a possible biomarker of psychotic disorders and an interesting pharmacological target to take into account for therapeutic purposes.

Validation of tautomeric and protomeric binding modes by free energy calculations. A case study for the structure based optimization of d-amino acid oxidase inhibitors

NASA Astrophysics Data System (ADS)

Orgován, Zoltán; Ferenczy, György G.; Steinbrecher, Thomas; Szilágyi, Bence; Bajusz, Dávid; Keserű, György M.

2018-02-01

Optimization of fragment size d-amino acid oxidase (DAAO) inhibitors was investigated using a combination of computational and experimental methods. Retrospective free energy perturbation (FEP) calculations were performed for benzo[d]isoxazole derivatives, a series of known inhibitors with two potential binding modes derived from X-ray structures of other DAAO inhibitors. The good agreement between experimental and computed binding free energies in only one of the hypothesized binding modes strongly support this bioactive conformation. Then, a series of 1-H-indazol-3-ol derivatives formerly not described as DAAO inhibitors was investigated. Binding geometries could be reliably identified by structural similarity to benzo[d]isoxazole and other well characterized series and FEP calculations were performed for several tautomers of the deprotonated and protonated compounds since all these forms are potentially present owing to the experimental pKa values of representative compounds in the series. Deprotonated compounds are proposed to be the most important bound species owing to the significantly better agreement between their calculated and measured affinities compared to the protonated forms. FEP calculations were also used for the prediction of the affinities of compounds not previously tested as DAAO inhibitors and for a comparative structure-activity relationship study of the benzo[d]isoxazole and indazole series. Selected indazole derivatives were synthesized and their measured binding affinity towards DAAO was in good agreement with FEP predictions.

Social Functioning Trajectories of Young First-Episode Psychosis Patients with and without Cannabis Misuse: A 30-Month Follow-Up Study

PubMed Central

González-Blanch, César; Gleeson, John F.; Koval, Peter; Cotton, Sue M.; McGorry, Patrick D.; Alvarez-Jimenez, Mario

2015-01-01

The aim of the study was to investigate trajectories of social functioning in young people with first-episode psychosis (FEP) with and without cannabis misuse using a secondary analysis of data from the Episode-II trial. Forty-two young people with FEP and comorbid cannabis use disorder were compared with 39 young people with FEP but without a cannabis use disorder. Social functioning was assessed every 6 months during a 30-month follow-up. Multilevel linear growth curve modeling was used to compare the social functioning trajectories over time for those with and without cannabis misuse. Cannabis misuse was not associated with social functioning at baseline assessment. Over a 30-month follow-up, FEP patients without cannabis disorder showed significant improvements in their social functioning, whereas patients with cannabis misuse at baseline displayed no such improvement. Patients with and without cannabis misuse differed significantly in their levels of social functioning after 24 months. Similar results were obtained after adjusting for potential confounders (i.e., age, gender, negative symptoms, premorbid functioning, DSM-IV diagnoses, baseline social functioning and other substance use). In the context of a specialized early intervention service, patients with cannabis misuse at baseline did not attain the improvements in social outcomes observed in their counterparts without cannabis misuse. There is a need to develop effective interventions to reduce cannabis misuse to ultimately improve social outcomes in young people with psychosis. PMID:25849623

Surmounting the Tower of Babel: Monolingual and bilingual 2-year-olds' understanding of the nature of foreign language words.

PubMed

Byers-Heinlein, Krista; Chen, Ke Heng; Xu, Fei

2014-03-01

Languages function as independent and distinct conventional systems, and so each language uses different words to label the same objects. This study investigated whether 2-year-old children recognize that speakers of their native language and speakers of a foreign language do not share the same knowledge. Two groups of children unfamiliar with Mandarin were tested: monolingual English-learning children (n=24) and bilingual children learning English and another language (n=24). An English speaker taught children the novel label fep. On English mutual exclusivity trials, the speaker asked for the referent of a novel label (wug) in the presence of the fep and a novel object. Both monolingual and bilingual children disambiguated the reference of the novel word using a mutual exclusivity strategy, choosing the novel object rather than the fep. On similar trials with a Mandarin speaker, children were asked to find the referent of a novel Mandarin label kuò. Monolinguals again chose the novel object rather than the object with the English label fep, even though the Mandarin speaker had no access to conventional English words. Bilinguals did not respond systematically to the Mandarin speaker, suggesting that they had enhanced understanding of the Mandarin speaker's ignorance of English words. The results indicate that monolingual children initially expect words to be conventionally shared across all speakers-native and foreign. Early bilingual experience facilitates children's discovery of the nature of foreign language words. Copyright © 2013 Elsevier Inc. All rights reserved.

Aberrant within- and between-network connectivity of the mirror neuron system network and the mentalizing network in first episode psychosis.

PubMed

Choe, Eugenie; Lee, Tae Young; Kim, Minah; Hur, Ji-Won; Yoon, Youngwoo Bryan; Cho, Kang-Ik K; Kwon, Jun Soo

2018-03-26

It has been suggested that the mentalizing network and the mirror neuron system network support important social cognitive processes that are impaired in schizophrenia. However, the integrity and interaction of these two networks have not been sufficiently studied, and their effects on social cognition in schizophrenia remain unclear. Our study included 26 first-episode psychosis (FEP) patients and 26 healthy controls. We utilized resting-state functional connectivity to examine the a priori-defined mirror neuron system network and the mentalizing network and to assess the within- and between-network connectivities of the networks in FEP patients. We also assessed the correlation between resting-state functional connectivity measures and theory of mind performance. FEP patients showed altered within-network connectivity of the mirror neuron system network, and aberrant between-network connectivity between the mirror neuron system network and the mentalizing network. The within-network connectivity of the mirror neuron system network was noticeably correlated with theory of mind task performance in FEP patients. The integrity and interaction of the mirror neuron system network and the mentalizing network may be altered during the early stages of psychosis. Additionally, this study suggests that alterations in the integrity of the mirror neuron system network are highly related to deficient theory of mind in schizophrenia, and this problem would be present from the early stage of psychosis. Copyright © 2018 Elsevier B.V. All rights reserved.

Birth weight and obstetric complications determine age at onset in first episode of psychosis.

PubMed

Rubio-Abadal, E; Ochoa, S; Barajas, A; Baños, I; Dolz, M; Sanchez, B; Del Cacho, N; Carlson, J; Huerta-Ramos, E; Usall, J

2015-06-01

Earlier age at onset of psychosis (AOP) has been associated with poor social adjustment and clinical outcome. Genetic and environmental factors such as obstetric complications, parental history of psychosis, advanced paternal age at time of birth, low birth weight and gestational age, and use of drugs have been described as bringing AOP forward. This study aims to evaluate the relationship between AOP and these factors in a sample of first episode of psychosis (FEP) patients. Clinical and sociodemographic data, age at FEP, age of parents at birth, parental history of psychosis, drug-use habits of the mother during pregnancy and of the patient before psychotic onset, and Lewis and Murray obstetric complication scale were obtained from 90 patients with FEP. Statistical analysis was performed by means of Pearson correlations, Chi-square tests, Student T-test analyses and a linear regression model using SPSS version 22. Pre-eclampsia, need for incubator at birth, use of forceps, parental history of psychosis, and low birth weight were associated with an earlier AOP. Use of forceps and birth weight are the variables which best predict AOP in FEP. Stimulant drugs, which were mostly used together with cannabis and cocaine, were the only substances associated with an earlier AOP. Our findings are consistent with previous study results and underline the role of the prenatal period in the development of psychosis and the importance of careful monitoring of pregnancy and delivery, especially in cases with familial history. Copyright © 2015 Elsevier Ltd. All rights reserved.

A Randomized Controlled Trial of Clinician-Supported Problem-Solving Bibliotherapy for Family Caregivers of People With First-Episode Psychosis.

PubMed

Chien, Wai Tong; Thompson, David R; Lubman, Dan I; McCann, Terence V

2016-11-01

Family interventions for first-episode psychosis (FEP) are an integral component of treatment, with positive effects mainly on patients' mental state and relapse rate. However, comparatively little attention has been paid to the effects of family interventions on caregivers' stress coping and well-being, especially in non-Western countries. We aimed to test the effects of a 5-month clinician-supported problem-solving bibliotherapy (CSPSB) for Chinese family caregivers of people with FEP in improving family burden and carers' problem-solving and caregiving experience, and in reducing psychotic symptoms and duration of re-hospitalizations, compared with those only received usual outpatient family support (UOFS). A randomized controlled trial was conducted across 2 early psychosis clinics in Hong Kong, where there might be inadequate usual family support services for FEP patients. A total of 116 caregivers were randomly selected, and after baseline measurement, randomly assigned to the CSPSB or UOFS. They were also assessed at 1-week and 6- and 12-month post-intervention. Intention-to-treat analyses were applied and indicated that the CSPSB group reported significantly greater improvements in family burden and caregiving experience, and reductions in severity of psychotic symptoms and duration of re-hospitalizations, than the UOFS group at 6- and 12-month follow-up. CSPSB produces moderate long-term benefits to caregivers and FEP patients, and is a low-cost adjunct to UOFS. © The Author 2016. Published by Oxford University Press on behalf of the Maryland Psychiatric Research Center.

Maintenance of storage properties of pediatric aliquots of apheresis platelets in fluoroethylene propylene containers.

PubMed

Skripchenko, Andrey; Myrup, Andrew; Thompson-Montgomery, Dedeene; Awatefe, Helen; Wagner, Stephen J

2013-04-01

Platelet (PLT) aliquots for pediatric use have been shown to retain in vitro properties when stored in gas-impermeable syringes for up to 6 hours. As an alternative, PLT aliquots can be stored for longer periods in containers used for storage of whole blood-derived PLTs. These containers are not available separate from whole blood collection sets and PLT volumes less than 35 mL either have not been evaluated or may be unsuitable for PLT storage. Gas-permeable fluoroethylene propylene (FEP) containers have been used in the storage of cell therapy preparations and are available in multiple sizes as single containers but have not been evaluated for PLT storage. A single apheresis unit was divided on Day 3 into small aliquots with volume ranging from 20 to 60 mL, transferred using a sterile connection device, and stored for an additional 2 days either in CLX (control) or in FEP containers. PLT storage properties of PLTs stored in FEP containers were compared to those stored in CLX containers. Standard PLT in vitro assays were performed (n =6). PLT storage properties were either similar to those of CLX containers or differed by less than 20% excepting carbon dioxide levels, which varied less than 60%. Pediatric PLT aliquots of 20, 30, and 60mL transferred on Day 3 into FEP cell culture containers adequately maintain PLT properties for an additional 2days of storage. © 2012 American Association of Blood Banks.

Toward a Model of Cognitive Insight in First-Episode Psychosis: Verbal Memory and Hippocampal Structure

PubMed Central

Buchy, L.; Czechowska, Y.; Chochol, C.; Malla, A.; Joober, R.; Pruessner, J.; Lepage, M.

2010-01-01

Our previous work has linked verbal learning and memory with cognitive insight, but not clinical insight, in individuals with a first-episode psychosis (FEP). The current study reassessed the neurocognitive basis of cognitive and clinical insight and explored their neural basis in 61 FEP patients. Cognitive insight was measured with the Beck Cognitive Insight Scale (BCIS) and clinical insight with the Scale to assess Unawareness of Mental Disorder (SUMD). Global measures for 7 domains of cognition were examined. Hippocampi were manually segmented in to 3 parts: the body, head, and tail. Verbal learning and memory significantly correlated with the BCIS composite index. Composite index scores were significantly associated with total left hippocampal (HC) volume; partial correlations, however, revealed that this relationship was attributable largely to verbal memory performance. The BCIS self-certainty subscale significantly and inversely correlated with bilateral HC volumes, and these associations were independent of verbal learning and memory performance. The BCIS self-reflectiveness subscale significantly correlated with verbal learning and memory but not with HC volume. No significant correlations emerged between the SUMD and verbal memory or HC volume. These results strengthen our previous assertion that in individuals with an FEP cognitive insight may rely on memory whereby current experiences are appraised based on previous ones. The HC may be a viable location among others for the brain system that underlies aspects of cognitive insight in individuals with an FEP. PMID:19346315

A decreased soluble Klotho level with normal eGFR, FGF23, serum phosphate, and FEP in an ADPKD patient with enlarged kidneys due to multiple cysts.

PubMed

Kanai, Takahiro; Shiizaki, Kazuhiro; Betsui, Hiroyuki; Aoyagi, Jun; Yamagata, Takanori

2018-05-16

Autosomal dominant polycystic kidney disease (ADPKD) is the most common hereditary renal disorder. ADPKD is characterized clinically by the presence of multiple bilateral renal cysts that lead to chronic renal failure. The cysts evolve from renal tubular epithelial cells that express the Klotho gene. Notably, Klotho acts as a co-receptor for fibroblast growth factor 23 (FGF23); in this context, it induces phosphaturia and maintains serum phosphate at a normal level. Many reports have shown that decreases in the soluble Klotho level and increases in the FGF23 level are associated with glomerular filtration rate (GFR) decline, but a recent study observed these changes in patient with normal eGFR. It remains unclear whether the decrease in the Klotho level precedes the increase in FGF23. Here, we present an ADPKD patient with enlarged kidneys due to multiple cysts who had a decreased soluble Klotho level but a normal eGFR and a normal FGF23 level. The patient's serum phosphate level was normal, as was the fractional excretion of phosphate (FEP). This appears to be the first reported case to show a decreased soluble Klotho level plus normal eGFR, FGF23, and FEP. These results suggest that Klotho decreases before FGF23 increases and further suggest that Klotho is not required to maintain normal serum phosphate levels in ADPKD if the FEP and serum phosphate levels are normal.

Social class at birth and risk of psychosis.

PubMed

O'Donoghue, Brian; Fanning, Felicity; Lyne, John; Renwick, Laoise; Madigan, Kevin; Kinsella, Anthony; Lane, Abbie; Turner, Niall; O'Callaghan, Eadbhard; Clarke, Mary

2015-12-01

Individuals with psychotic disorders are represented more in the lower social classes, yet there is conflicting evidence to whether these individuals drift into the lower social classes or whether lower social class is a risk factor for developing psychosis. The aim of this study was to examine whether the social class at birth is a risk factor for developing psychosis. We included individuals with a first episode of psychosis (FEP) whose social class at birth was determined from birth records. We employed a case-control study design and also compared the distribution of the social classes at birth of the cases to that of the general population. A total of 380 individuals with an FEP and 760 controls were included in the case-control study. The odds ratio for developing an FEP associated with social class (low vs high) was .62 (95% confidence interval (CI): .46-.85, p < .001), indicating that individuals from a lower social class at birth have a reduced risk of psychosis. Individuals born between 1961 and 1980 with an FEP were more likely to be from a higher social class at birth compared to the general population (60.8% vs 36.7%, χ(2) = 60.85, df = 1, p < .001). However, this association was not observed for those born between 1981 and 1990. A higher social class at birth is associated with a greater risk for developing a psychotic disorder; however, this effect may show temporal variation. © The Author(s) 2015.

MUTAGENICITY OF TEFLON-COATED GLASS FIBER FILTERS: A POTENTIAL PROBLEM AND SOLUTIONS

EPA Science Inventory

Teflon-coated glass fiber filters, used in studies of airborne particulate matter, were tested for mutagenic activity using the Salmonella/mammalian-microsome (Ames) assay. For each sample, eight blank filters were simultaneously extracted with dichloromethane (DCM), and the extr...

Molybdeno-Aluminizing of Powder Metallurgy and Wrought Ti and Ti-6Al-4V alloys by Pack Cementation process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsipas, Sophia A., E-mail: stsipas@ing.uc3m.es; Go

Wear and high temperature oxidation resistance of some titanium-based alloys needs to be enhanced, and this can be effectively accomplished by surface treatment. Molybdenizing is a surface treatment where molybdenum is introduced into the surface of titanium alloys causing the formation of wear-resistant surface layers containing molybdenum, while aluminizing of titanium-based alloys has been reported to improve their high temperature oxidation properties. Whereas pack cementation and other surface modification methods have been used for molybdenizing or aluminizing of wrought and/or cast pure titanium and titanium alloys, such surface treatments have not been reported on titanium alloys produced by powder metallurgymore » (PM). Also a critical understanding of the process parameters for simultaneous one step molybdeno-aluminizing of titanium alloys by pack cementation and the predominant mechanism for this process have not been reported. The current research work describes the surface modification of titanium and Ti-6Al-4V prepared by PM by molybdeno-aluminizing and analyzes thermodynamic aspects of the deposition process. Similar coatings are also deposited to wrought Ti-6Al-4V and compared. Characterization of the coatings was carried out using scanning electron microscopy and x-ray diffraction. For both titanium and Ti-6Al-4V, the use of a powder pack containing ammonium chloride as activator leads to the deposition of molybdenum and aluminium into the surface but also introduces nitrogen causing the formation of a thin titanium nitride layer. In addition, various titanium aluminides and mixed titanium aluminium nitrides are formed. The appropriate conditions for molybdeno-aluminizing as well as the phases expected to be formed were successfully determined by thermodynamic equilibrium calculations. - Highlights: •Simultaneous co-deposition of Mo-Al onto powder metallurgy and wrought Ti alloy •Thermodynamic calculations were used to optimize deposition conditions •External TiN and internal a Mo-rich layer on all alloy substrates •Titanium aluminides and Ti-Al mixed nitrides are formed on Ti-6Al-4V •The presence of Al and V alloying elements modifies the diffusion of Mo.« less

Teflon/SiO2 Bilayer Passivation for Improving the Electrical Reliability of Oxide TFTs Fabricated Using a New Two-Photomask Self-Alignment Process

PubMed Central

Fan, Ching-Lin; Shang, Ming-Chi; Li, Bo-Jyun; Lin, Yu-Zuo; Wang, Shea-Jue; Lee, Win-Der; Hung, Bohr-Ran

2015-01-01

This study proposes a two-photomask process for fabricating amorphous indium–gallium–zinc oxide (a-IGZO) thin-film transistors (TFTs) that exhibit a self-aligned structure. The fabricated TFTs, which lack etching-stop (ES) layers, have undamaged a-IGZO active layers that facilitate superior performance. In addition, we demonstrate a bilayer passivation method that uses a polytetrafluoroethylene (Teflon) and SiO2 combination layer for improving the electrical reliability of the fabricated TFTs. Teflon was deposited as a buffer layer through thermal evaporation. The Teflon layer exhibited favorable compatibility with the underlying IGZO channel layer and effectively protected the a-IGZO TFTs from plasma damage during SiO2 deposition, resulting in a negligible initial performance drop in the a-IGZO TFTs. Compared with passivation-free a-IGZO TFTs, passivated TFTs exhibited superior stability even after 168 h of aging under ambient air at 95% relative humidity. PMID:28788026

Poststapedectomy hearing gain: comparison of a Teflon (fluoroplastic ASTM F 754) prosthesis with a Schuknecht-type wire/Teflon prosthesis.

PubMed

Zepeda-López, Emilia Guadalupe; Bello-Mora, Antonio; Félix-Trujillo, Manuel Martín

2005-11-01

We conducted a retrospective study to compare poststapedectomy hearing gain in study-eligible patients who had received a Teflon (fluoroplastic ASTM F 754) prosthesis (study group; n = 76) with hearing gain achieved in a matched group (by age, sex, and degree of hypoacusis) of patients who had received a Schuknecht-type wire/Teflon prosthesis (control group; n = 70). All procedures had been performed by the authors at our institution between Jan. 2, 1994, and Dec. 31, 1997. Airway averages at low, medium, and high frequencies were estimated on the basis ofpre- and postoperative audiologic evaluations, as were total air-bone gaps at 7 frequencies between 125 and 8, 000 Hz. We found that the study group achieved a significantly greater degree of hearing gain at 125 and 250 Hz and significantly better closure of the air-bone gap at 250, 500, 1,000, 2,000, and 4,000 Hz. The hearing outcomes among patients in the study group were excellent.

Resistance of Spores of Bacillus subtilis var. niger on Kapton and Teflon Film to High Temperature and Dry Heat

PubMed Central

Bruch, Mary K.; Smith, Frederick W.

1968-01-01

To determine parameters that would assure sterility of a sealed seam of film for application in “split-seam entry,” spores of Bacillus subtilis var. niger were sprayed onto pieces of Kapton and Teflon film. Short-time, high-temperature (200 to 270 C) exposures were made with film pieces between aluminum blocks in a hot-air oven, and the D and z values were determined after subculture of surviving spores. The use of Kapton film allowed the study of high temperatures, since it is not heat sealable and could be used to make thin packages for heat treatment. Spores on Teflon were dry-heat treated in a package designed to simulate an actual seam to be sealed. The z values of 29.1 C (52.4 F) for spores on Kapton and 139 C (250.4 F) for spores on Teflon were calculated. Images Fig. 1 Fig. 2 Fig. 3 PMID:4973071

Cratering and penetration experiments in teflon targets at velocities from 1 to 7 km/s

NASA Technical Reports Server (NTRS)

Horz, Friedrich; Cintala, Mark; Bernhard, Ronald P.; Cardenas, Frank; Davidson, William; Haynes, Gerald; See, Thomas H.; Winkler, Jerry; Knight, Jeffrey

1994-01-01

Approximately 20 sq m of protective thermal blankets, largely composed of Teflon, were retrieved from the Long Duration Exposure Facility after the spacecraft spent approximately 5.7 years in space. Examination of these blankets revealed that they contained thousands of hypervelocity impact features ranging from micron-sized craters to penetration holes several millimeters in diameter. We conducted impact experiments to reproduce such features and to understand the relationships between projectile size and the resulting crater or penetration hole diameter over a wide range of impact velocities. Such relationships are needed to derive the size and mass frequency distribution and flux of natural and man-made particles in low-earth orbit. Powder propellant and light-gas guns were used to launch soda-lime glass spheres into pure Teflon targets at velocities ranging from 1 to 7 km/s. Target thickness varied over more than three orders of magnitude from finite halfspace targets to very thin films. Cratering and penetration of massive Teflon targets is dominated by brittle failure and the development of extensive spall zones at the target's front and, if penetrated, the target's rear side. Mass removal by spallation at the back side of Teflon targets may be so severe that the absolute penetration hole diameter can become larger than that of a standard crater. The crater diameter in infinite halfspace Teflon targets increases, at otherwise constant impact conditions, with encounter velocity by a factor of V (exp 0.44). In contrast, the penetration hole size in very thin foils is essentially unaffected by impact velocity. Penetrations at target thicknesses intermediate to these extremes will scale with variable exponents of V. Our experimental matrix is sufficiently systematic and complete, up to 7 km/s, to make reasonable recommendations for velocity-scaling of Teflon craters and penetrations. We specifically suggest that cratering behavior and associated equations apply to all impacts in which the shock-pulse duration of the projectile is shorter than that assigned a unique projectile size, provided an impact velocity is known or assumed. This calibration seems superior to the traditional ballistic-limit approach.

Reuse of ornamental rock-cutting waste in aluminous porcelain.

PubMed

Silva, M A; Paes, H R; Holanda, J N F

2011-03-01

Large amounts of solid wastes are discarded in the ornamental rocks industry. This work investigates the incorporation of ornamental rock-cutting waste as a raw material into an aluminous porcelain body, replacing natural feldspar material by up to 35 wt.%. Formulations containing rock-cutting waste were pressed and sintered at 1350 °C. The porcelain pieces were tested to determine their properties (linear shrinkage, water absorption, apparent density, mechanical strength, and electrical resistivity). Development of the microstructure was followed by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses. The results showed that ornamental rock-cutting waste could be used in aluminous porcelains, in the range up to 10 wt.%, as a partial replacement for traditional flux material, resulting in a valid route for management of this abundant waste. Copyright © 2010 Elsevier Ltd. All rights reserved.

Response to ``Comment on `Slow Debye-type peak observed in the dielectric response of polyalcohols' '' [J. Chem. Phys. 134, 037101 (2011)

NASA Astrophysics Data System (ADS)

Bergman, R.; Jansson, H.; Swenson, J.

2011-01-01

In our recent article [R. Bergman et al., J. Chem. Phys. 132, 044504 (2010)] we investigated some polyalcohols, i.e., glycerol, xylitol, and sorbitol by dielectric spectroscopy. In the study, a low-frequency peak of Debye character that normally is hidden by the large low-frequency dispersion due to conductivity was revealed by analyzing the real part of the permittivity and by using a thin Teflon film to suppress the low-frequency dispersion. We agree with the comment by Paluch et al. [J. Chem. Phys. 134, 037101 (2011)] that the Teflon film setup will indeed create a peak due to the dc conductivity. However, due to the fact that the location of the peak was almost identical in measurement with and without Teflon, we unfortunately mainly showed the data measured with Teflon, despite that it could also be observed in the real part of the permittivity without using the Teflon setup, as shown in our original article [R. Bergman et al., J. Chem. Phys. 132, 044504 (2010)]. Here, we show that the low-frequency peak of Debye character can also be observed by subtracting the dc conductivity. Furthermore, we show that the modulus representation used in Paluch et al. [J. Chem. Phys. 134, 037101 (2011).] is also not suitable for detecting processes hidden by the conductivity.

Effect of friction on shear jamming

NASA Astrophysics Data System (ADS)

Wang, Dong; Ren, Jie; Dijksman, Joshua; Behringer, Robert

2014-03-01

Shear Jamming of granular materials was first found for systems of frictional disks, with a static friction coefficients μs ~= 0 . 6 . Jamming by shear is obtained by starting from a zero-stress state with a packing fraction ϕS <= ϕ <=ϕJ between ϕJ (isotropic jamming) and a lowest ϕS for shear jamming. This phenomenon is associated with strong anisotropy in stress and the contact network in the form of ``force chains,'' which are stabilized and/or enhanced by the presence of friction. We address experimentally how reducing friction affects shear jamming by using either teflon disks of teflon wrapped photoelastic particles. The teflon disks were placed in a wall driven 2D shear apparatus, in which we can probe shear stresses mechanically. Teflon-wrapped disks were placed in a bottom driven 2D shear apparatus (Ren et al., PRL 2013). Both apparatuses provide uniform simple shear. In all low- μ experiments, the shear jamming occurred, as observed through stress increases on the packing. However, the low- μ differences observed for ϕJ -ϕS were smaller than for higher friction particles. Ongoing work is studying systems using hydrogel disks, which have a lower friction coefficient than teflon. We acknowledge support from NSF Grant No. DMR12-06351, ARO Grant No. W911NF-1-11-0110, and NASA Grant No. NNX10AU01G.

Capping a Pulpotomy with Calcium Aluminosilicate Cement: Comparison to Mineral Trioxide Aggregates

PubMed Central

Kramer, Phillip R.; Woodmansey, Karl F.; White, Robert; Primus, Carolyn M.; Opperman, Lynne A.

2014-01-01

Introduction Calcium aluminate cements have shown little affinity for bacterial growth, low toxicity, and immunogenicity when used as a restoration material, but calcium aluminate cements have not been tested in vivo in pulpotomy procedures. Methods To address this question, a calcium aluminate cement (Quick-Set) was tested along with 2 mineral trioxide aggregates, ProRoot MTA and MTA Plus. These cements were used as a capping agent after pulpotomy. Control rats had no pulpotomy, or the pulpotomy was not capped. Proinflammatory cytokines interleukin (IL)-1β and IL-1α were measured, and histology was performed at 30 and 60 days after capping. The nociceptive response was determined by measuring the lengthening of the rat's meal duration. Results and Conclusions: IL-1β and IL-1α concentrations were reduced in the capped teeth, but no differences were observed among the 3 cements. Dentinal bridging could be detected at both 30 and 60 days with each of the 3 cements, and the pulps were still vital 60 days after capping. Meal duration significantly shortened after placement of the 3 different cements, indicating a nociceptive response, but there were no differences among the materials. Calcium aluminate cements had similar properties to mineral trioxide aggregates and is a viable option for pulpotomy procedures. PMID:25146026

Driving Ability of HMX based Aluminized Explosive Affected by the Reaction Degree of Aluminum Powder

NASA Astrophysics Data System (ADS)

Duan, Yingliang

2017-06-01

Due to the time scale of aluminum reaction, the detonation process of the aluminized explosive becomes very complex, and there is less agreement on the reaction mechanism of aluminum powder. If the reaction of aluminum occurs in the reaction zone, the energy released will further strengthen the work ability of detonation wave. So it is very important for characterizing the detonation parameters and detonation driving ability to accurately understand the role of aluminum powder in the reaction zone. In this paper, detonation driving process of HMX based aluminized explosive was studied by cylinder test, obtaining the expansion track of cylinder wall. In order to further research the reaction degree (λ) of aluminum in the reaction zone, the thermodynamic program VHL was used to calculate the detonation process at different reaction degrees, obtaining the parameters of detonation products thermodynamic state. Using the dynamic software LS-DYNA and the JWL equation of state by fitting the pressure and relative volume relationship, the cylinder test was simulated. Compared with the experimental results, when the reaction degree is 20%, the driving ability is found to be in agreement with measured ones. It is concluded that the driving ability of HMX based aluminized explosive can be more accurately characterized by considering the reaction degree of aluminum powder in the reaction zone.

The effect of explosive percentage on underwater explosion energy release of hexanitrohexaazaisowurtzitane and octogen based aluminized explosives

NASA Astrophysics Data System (ADS)

Jiao, Qingjie; Wang, Qiushi; Nie, Jianxin; Guo, Xueyong; Zhang, Wei; Fan, Wenqi

2018-03-01

To control the explosion energy output by optimizing explosive components is a key requirement in a number of different application areas. The effect of different Al/O Ratio on underwater explosion of aluminized explosives has been studied detailedly. However, the effect of explosive percentage in the same Al/O Ratio is rarely researched, especially for Hexanitrohexaazaisowurtzitane (CL-20) based aluminized explosives. In this study, we performed the underwater explosion experiments with 1.2-kilogram explosives in order to investigate the explosion energy released from CL-20 and Octogen (HMX) based aluminized explosives. The percentage of the explosive varied from 5% to 30% and it is shown that: the shockwave peak pressure (pm) grows gradually; shock wave energy (Es) continues increasing, bubble energy (Eb) increases then decreases peaking at 15% for both formulas, and the total energy (E) and energy release rate (η) peak at 20% for CL-20 and 15% for HMX. This paper outlines the physical mechanism of Eb change under the influence of an aluminium initial reaction temperature and reaction active detonation product percentage coupling. The result shows that CL-20 is superior as a new high explosive and has promising application prospects in the regulation of explosive energy output for underwater explosives.

Mass transfer in fuel cells. [electron microscopy of components, thermal decomposition of Teflon, water transport, and surface tension of KOH solutions

NASA Technical Reports Server (NTRS)

Walker, R. D., Jr.

1973-01-01

Results of experiments on electron microscopy of fuel cell components, thermal decomposition of Teflon by thermogravimetry, surface area and pore size distribution measurements, water transport in fuel cells, and surface tension of KOH solutions are described.

Demonstrating a Lack of Reactivity Using a Teflon-Coated Pan.

ERIC Educational Resources Information Center

Richmond, Thomas G.

1995-01-01

Illustrates the chemical resistance of polytetrafluoroethene to mineral acids using an ordinary Teflon-coated frying pan. The demonstration can also be used to lead to a discussion of the long lifetimes of fluorocarbons and chlorofluorocarbons in the atmosphere and their roles in the breakdown of the ozone layer. (AIM)

75 FR 77790 - Airworthiness Directives; The Boeing Company Model 767 Series Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-14

... repetitive inspections to detect discrepancies of the wiring and surrounding Teflon sleeves of the fuel tank... airplanes; and repair or replacement of the wiring and sleeves with new parts, as necessary. This proposed...).) That AD requires repetitive inspections to detect discrepancies of the wiring and surrounding Teflon...

Recovery in remitted first-episode psychosis at 7 years of follow-up of an early dose reduction/discontinuation or maintenance treatment strategy: long-term follow-up of a 2-year randomized clinical trial.

PubMed

Wunderink, Lex; Nieboer, Roeline M; Wiersma, Durk; Sytema, Sjoerd; Nienhuis, Fokko J

2013-09-01

Short-term outcome studies of antipsychotic dose-reduction/discontinuation strategies in patients with remitted first-episode psychosis (FEP) showed higher relapse rates but no other disadvantages compared with maintenance treatment; however, long-term effects on recovery have not been studied before. To compare rates of recovery in patients with remitted FEP after 7 years of follow-up of a dose reduction/discontinuation (DR) vs maintenance treatment (MT) trial. Seven-year follow-up of a 2-year open randomized clinical trial comparing MT and DR. One hundred twenty-eight patients participating in the original trial were recruited from 257 patients with FEP referred from October 2001 to December 2002 to 7 mental health care services in a 3.2 million-population catchment area. Of these, 111 patients refused to participate and 18 patients did not experience remission. PARTICIPANTS After 7 years, 103 patients (80.5%) of 128 patients who were included in the original trial were located and consented to follow-up assessment. After 6 months of remission, patients were randomly assigned to DR strategy or MT for 18 months. After the trial, treatment was at the discretion of the clinician. Primary outcome was rate of recovery, defined as meeting the criteria of symptomatic and functional remission. Determinants of recovery were examined using logistic regression analysis; the treatment strategy (MT or DR) was controlled for baseline parameters. The DR patients experienced twice the recovery rate of the MT patients (40.4% vs 17.6%). Logistic regression showed an odds ratio of 3.49 (P = .01). Better DR recovery rates were related to higher functional remission rates in the DR group but were not related to symptomatic remission rates. Dose reduction/discontinuation of antipsychotics during the early stages of remitted FEP shows superior long-term recovery rates compared with the rates achieved with MT. To our knowledge, this is the first study showing long-term gains of an early-course DR strategy in patients with remitted FEP. Additional studies are necessary before these results are incorporated into general practice. isrctn.org Identifier: ISRCTN16228411.

Evaluation of attenuated PSM photomask blanks with TF11 chrome and FEP-171 resist on a 248 nm DUV laser pattern generator

NASA Astrophysics Data System (ADS)

Xing, Kezhao; Björnborg, Charles; Karlsson, Henrik; Paulsson, Adisa; Rosendahl, Anna; Beiming, Peter; Vedenpää, Jukka; Walford, Jonathan; Newman, Tom

2007-10-01

Tighter requirements on mask resolution, CD and image positioning accuracy at and beyond the 45 nm technology node push the development of improved photomask blanks. One such blank for attenuated phase-shift masks (att-PSM) provides a thinner chrome film, named TF11, with higher chrome etch rate compared to the previous generation Att- PSM blank (NTAR5 chrome film) from the same supplier. Reduced stress in the chrome film also results in less image placement error induced by the material. FEP-171 is the positive chemically amplified resist (PCAR) that is most commonly used in advanced mask manufacturing with both 50 keV variable shaped e-beam (VSB) and DUV laser pattern generators. TF11 allows an FEP-171 resist film down to about 2000 Å thickness with sufficient etch resistance, while the standard resist thickness for NTAR5 is around 3000 Å. This work has experimentally evaluated the use of TF11 chrome and FEP-171 resist together with a 248 nm DUV laser pattern generator, the Sigma7500. First, patterning performance in resist with thicknesses from 2000 Å to 2600 Å, in steps of 100 Å, was tested with respect to swing curve and basic lithographic parameters including resolution, CD linearity, CD iso-dense bias and dose sensitivity. Patterning results on mask showed a swing minimum at around 2200 Å and a swing maximum at around 2500 Å, which correspond to reflectivity measurements for 248 nm wavelength performed by the blank supplier. It was concluded that the overall patterning performance was best close to the swing maximum. Thereafter the patterning performance using TF11 at two resist thicknesses, 2000 Å and 2550 Å, was studied in more detail and compared to performance using NTAR5 with 3200 Å resist. The evaluation showed that the Sigma7500-II offers good compatibility with TF11, especially using the optimized FEP-171 resist thickness of 2550 Å. It also showed that the patterning capability of the Sigma7500-II using TF11 and 2550 Å resist is improved compared to using NTAR5 and 3200 Å resist.

Experimental microbiological issues related to biocontamination and human life support inside manned space modules

NASA Astrophysics Data System (ADS)

Canganella, Francesco; Rettberg, Petra; Bianconi, G.; di Mattia, E.; Taddei, A. R.; Iylin, V.; Novikova, N.; Fani, R.; Brigidi, P.; Vitali, B.; Candela, M.; Lobascio, C.; Saverino, A.; Simone, A.; Fossati, F.; Ferraris, M.

The issue of biocontamination in manned space modules is very important for the International Space Station (ISS) as well as for future planetary bases. We have previously carried out re-search activities concerning biofilm metabolic activities of some reference bacteria on materials commonly used for aerospace industry and currently examined for space greenhouses. It was evaluated the effect on these materials of a mixture of emulsifiers produced by Pseudomonas strain AD1 and recently characterized by chemical methods. The following materials were in-vestigated: Kevlar, Nomex, Betacloth, aluminized Kapton, conventional Kapton, Combitherm, Mylar, copper foil, Teflon, aluminum, carbon fiber composite, aluminum thermo-dissipating tex-tile, aluminum tape, Zylon, Ergoflex, Vectran. Results showed a diverse affinity of materials for bacterial biofilm formation and occasionally sessile colonization was rejected. Pre-conditioning with the emulsifying extract led in some cases to a diminish of biofilm dehydrogenase activity and development compared to untreated materials, taking into account both concentrations and experimental conditions. This also concerned the relationship between the physical traits of materials and the level of bacterial biofilm developed under the experimental conditions. Presently we are investigating microbial biofilm development on either conventional or innova-tive space materials, experimentally treated by biological or chemo-physical coating. VIABLE ISS is a flight experiment concerning the exposure of these materials inside an ISS module for about 4 years. Another initiative (MICHA) on progress is part of the MARS500 Programme, presently going on at the IBMP facility in Moscow. Data will be useful to select appropriate material to be used for life support hardware to decrease the risk of surface biocontamination and health problems inside space modules, a great challenge for both biological and medical research.

Insight and suicidality in first-episode psychosis: understanding the influence of suicidal history on insight dimensions at first presentation.

PubMed

López-Moríñigo, Javier D; Wiffen, Benjamin; O'Connor, Jennifer; Dutta, Rina; Di Forti, Marta; Murray, Robin M; David, Anthony S

2014-05-01

Lack of insight is a cardinal feature of psychosis with crucial implications for outcome. Concerns have been raised regarding a link between insight and suicidality. This study aimed to test the relationship between suicidal behaviour preceding first-episode psychosis (FEP) and insight dimensions at treatment onset. A total of 112 FEP inpatients were recruited. Suicidal events prior to admission were recorded. Insight was assessed multidimensionally with the Schedule for the Assessment of Insight - Expanded version shortly after admission. Suicidal and non-suicidal patients were compared regarding scores on 'total insight' and three insight domains: 'awareness of mental illness', 'relabeling of psychotic experiences as abnormal' and 'compliance'. This analysis was also adjusted for a set of sociodemographic, clinical, neurocognitive and psychopathological variables. Bivariate analyses demonstrated a direct association between previous suicidality and all insight domains. However, these associations did not survive multivariable regression models, which demonstrated gender (female), shorter duration of untreated psychosis (DUP) and psychopathological symptoms - depression and disorganization - to mediate the influence of suicidal history on insight, and therefore to underlie the latter. Insight dimensions in FEP patients are influenced by having suicidal antecedents through some mediating variables such as gender, DUP and depression. Further prospective studies are needed to clarify the potential implications of these findings on the management of insight in FEP. As suicidal history is associated with greater levels of both depression and insight at first presentation, these three variables might be useful in predicting further suicidal events. © 2013 Wiley Publishing Asia Pty Ltd.

Substance abuse and gender differences in first episode psychosis: Impact on hospital readmissions.

PubMed

Crosas, Josep M; Cobo, Jesus; Ahuir, Maribel; Hernández, Carla; García, Rebeca; Pousa, Esther; Oliva, Joan-Carles; Monreal, José-Antonio; Palao, Diego J

There have been controversial results in the study of gender differences in first episode psychosis (FEP). Substance abuse is the main existing comorbidity in FEP, and has been associated with worse prognosis and greater symptom severity. To explore gender differences in FEP in relation to drug abuse, and their relationship with hospital readmissions. Descriptive and prospective study (18 months). We included 141 patients (31.2% women), aged 26.1 years on average, mostly diagnosed with schizophreniform disorder (32.6%). A percentage of 58.9 had problematic use of drugs. Gender significant differences were found in age of onset, age at entry to the programme, marital status and cohabitation, and percentage differences were revealed in current drug abuse and frequency of consumption. Gender, duration of untreated psychosis, psychiatric history, age of onset and previous drug use were not predictors of re-entry. Hospital readmission rate was 24.8%, with no gender differences. The most common reasons for admission were abandonment of treatment (66.7%) and drug abuse (44.4%). Drug abuse was higher in the men than in the women as a reason for re-admission. There are gender differences in FEP. Men have an earlier onset of symptoms and have worse functional outcomes. Drug abuse in men is higher and represents a major cause of hospital readmission. Therapeutic interventions to prevent the effects of drug abuse are necessary from the early stages of the illness. Copyright © 2017 SEP y SEPB. Publicado por Elsevier España, S.L.U. All rights reserved.

Self-stigma and affiliate stigma in first-episode psychosis patients and their caregivers.

PubMed

Chen, Emily S M; Chang, Wing Chung; Hui, Christy L M; Chan, Sherry K W; Lee, Edwin Ho Ming; Chen, Eric Y H

2016-09-01

Stigma is a major factor causing delayed help-seeking and poor treatment adherence in patients with psychotic disorders. Previous research has mostly focused on chronic samples and the impact of culturally-relevant variables on both patients' and their caregivers' stigmatization is understudied. This study aimed to examine the relationships between various forms of stigma, "face concern", and clinical characteristics in a group of Chinese first-episode psychosis (FEP) patients and their caregivers. Forty-four Hong Kong Chinese aged 15-54 years presenting with FEP to psychiatric services and their caregivers were recruited. Assessments on self-stigma, affiliate stigma, perceived public stigma, "face concern", symptom severity and subjective quality of life (QoL) were conducted. Self-stigma of FEP patients was correlated with perceived public stigma, "face concern", insight and psychological health of QoL. Multiple regression analysis revealed that perceived public stigma and "face concern" independently predicted self-stigma. Mediation analysis further suggested that "face concern" partially mediated the relationship between perceived public stigma and self-stigma. Caregivers' affiliate stigma was significantly associated with higher levels of stress, and symptoms of depression and anxiety. Affiliate stigma did not correlate with perceived public stigma and "face concern". Our results indicate a critical role of perceived public stigma and fear of losing face in determining self-stigma in Chinese patients with FEP. Caregivers with greater degree of affiliate stigma experience increased stress and emotional distress. Our findings highlight the importance to examine culturally specific factors that may contribute to the development of self-stigma in first-episode populations of different ethnicities.

Dynamics of ion beam charge neutralization by ferroelectric plasma sources

DOE PAGES

Stepanov, Anton D.; Gilson, Erik P.; Grisham, Larry R.; ...

2016-04-27

Ferroelectric Plasma Sources (FEPSs) can generate plasma that provides effective space-charge neutralization of intense high-perveance ion beams, as has been demonstrated on the Neutralized Drift Compression Experiment NDCX-I and NDCX-II. This article presents experimental results on charge neutralization of a high-perveance 38 keV Ar + beam by a plasma produced in a FEPS discharge. By comparing the measured beam radius with the envelope model for space-charge expansion, it is shown that a charge neutralization fraction of 98% is attainable with sufficiently dense FEPS plasma. The transverse electrostatic potential of the ion beam is reduced from 15V before neutralization to 0.3more » V, implying that the energy of the neutralizing electrons is below 0.3 eV. Measurements of the time-evolution of beam radius show that near-complete charge neutralization is established similar to –5 μs after the driving pulse is applied to the FEPS and can last for 35 μs. It is argued that the duration of neutralization is much longer than a reasonable lifetime of the plasma produced in the sub-mu s surface discharge. Measurements of current flow in the driving circuit of the FEPS show the existence of electron emission into vacuum, which lasts for tens of mu s after the high voltage pulse is applied. Lastly, it is argued that the beam is neutralized by the plasma produced by this process and not by a surface discharge plasma that is produced at the instant the high-voltage pulse is applied.« less

Cultural and social influences of negative illness appraisals in first-episode psychosis.

PubMed

Upthegrove, Rachel; Atulomah, Onyekachi; Brunet, Kat; Chawla, Rajan

2013-11-01

In the UK, there has been growing concern about the incidence and prognosis of psychosis in minority ethnic groups for a number of years. Negative self-appraisals after first-episode psychosis (FEP) are associated with post-psychotic depression, poor functioning and suicidality. In carers, appraisals of loss and decreased control are linked with high expressed emotion and relapse; however, as yet there has been no investigation as to how ethnicity and culture relate to these negative appraisals in FEP. The study aims to investigate the occurrence of negative illness appraisals, for example, loss and shame, in FEP within different ethnic and social-cultural groups. In addition, it aims to explore influence of insight, recovery style and carers' appraisals in the development of negative appraisals. There were 67 patients and 46 carers who completed reliable and valid measures on beliefs about illness, insight and recovery style. Data on ethnicity and deprivation were also collected. Black patients experienced significantly less loss, lack of control and entrapment than White, Asian and mixed ethnicity patients, yet these were not explained by lower levels of insight or recovery style. Patient's and carer's appraisals were highly correlated. Black patients, in spite of higher incidence and poorer outcome in FEP, experienced less loss and shame. Possible explanations, including a protective aspect of alternative health belief models, are explored. This area provides much scope for further investigation. Strong relationships between patient and carer appraisals indicate that family interventions are essential to improved clinical outcomes. © 2012 Wiley Publishing Asia Pty Ltd.

Social cognitive markers of short-term clinical outcome in first-episode psychosis.

PubMed

Montreuil, Tina; Bodnar, Michael; Bertrand, Marie-Claude; Malla, Ashok K; Joober, Ridha; Lepage, Martin

2010-07-01

In psychotic disorders, impairments in cognition have been associated with both clinical and functional outcome, while deficits in social cognition have been associated with functional outcome. As an extension to a recent report on neurocognition and short-term clinical outcome in first-episode psychosis (FEP), the current study explored whether social cognitive deficits could also identify poor short-term clinical outcome among FEP patients. We defined the social-cognition domain based on the scores from the Hinting Task and the Four Factor Tests of Social Intelligence. Data were collected in 45 FEP patients and 26 healthy controls. The patients were divided into good- and poor-outcome groups based on clinical data at six months following initiation of treatment. Social cognition was compared among 27 poor-outcome, 18 good-outcome, and 26 healthy-control participants. Outcome groups significantly differed in the social cognition domain (z-scores: poor outcome=-2.0 [SD=1.4]; good outcome=-1.0 [SD=1.0]; p=0.005), with both groups scoring significantly lower than the control group (p<0.003). Moreover, outcome groups differed significantly only on the Cartoon Predictions subtest (z-scores: poor outcome=-2.7 [SD=2.7]; good outcome=-0.7 [SD=1.8]; p=0.001) among the five subtests used. Overall, social cognition appears to be compromised in all FEP patients compared to healthy controls. More interestingly, significant differences in social cognitive impairments exist between good and poor short-term clinical outcome groups, with the largest effect found in the Cartoon Predictions subtest.

The relationships of suicidal ideation with symptoms, neurocognitive function, and psychological factors in patients with first-episode psychosis.

PubMed

Chang, Wing Chung; Chen, Emily Sze Man; Hui, Christy Lai Ming; Chan, Sherry Kit Wa; Lee, Edwin Ho Ming; Chen, Eric Yu Hai

2014-08-01

Individuals with first-episode psychosis (FEP) have markedly elevated risk for suicide. Previous research on suicidality in early psychosis mainly focused on attempted and completed suicide. Data regarding risk factors for suicidal ideation, which is a common antecedent and predictor of suicide attempt, were limited. This study aimed to examine the prevalence of suicidal ideation and its relationships with clinical, neurocognitive and psychological factors in FEP patients. Eighty-nine Chinese patients aged 15 to 25years presenting with FEP to specialized early intervention service were recruited. A comprehensive set of assessments examining pre-treatment illness characteristics, symptom severity, neurocognitive function, and psychological factors were administered. Current suicidal ideation and history of suicide attempt were systematically evaluated. Approximately 42% of patients expressed suicidal ideation after service entry. Univariate regression analyses found that suicidal ideation was significantly associated with past suicide attempt, depressive symptoms, emotion expressivity, hopelessness, future expectation, attentional impulsiveness, internal and external locus of control, and the likelihood of endorsing fear of social approval and survival and coping beliefs as reasons for living. Final multivariate model showed that previous suicide attempt, depression, less severe diminished expression, greater degree of hopelessness and lower level of internal locus of control independently predicted suicidal ideation. Suicidal ideation was prevalent in FEP patients. Our findings implied that close monitoring and prompt intervention of those potentially modifiable risk factors for suicidal ideation including depression, hopelessness and perceived inadequate personal control may reduce suicide risk in the early course of psychotic illness. Copyright © 2014 Elsevier B.V. All rights reserved.

Facial affect recognition in early and late-stage schizophrenia patients.

PubMed

Romero-Ferreiro, María Verónica; Aguado, Luis; Rodriguez-Torresano, Javier; Palomo, Tomás; Rodriguez-Jimenez, Roberto; Pedreira-Massa, José Luis

2016-04-01

Prior studies have shown deficits in social cognition and emotion perception in first-episode psychosis (FEP) and multi-episode schizophrenia (MES) patients. These studies compared patients at different stages of the illness with only a single control group which differed in age from at least one clinical group. The present study provides new evidence of a differential pattern of deficit in facial affect recognition in FEP and MES patients using a double age-matched control design. Compared to their controls, FEP patients only showed impaired recognition of fearful faces (p=.007). In contrast to this, the MES patients showed a more generalized deficit compared to their age-matched controls, with impaired recognition of angry, sad and fearful faces (ps<.01) and an increased misattribution of emotional meaning to neutral faces. PANSS scores of FEP patients on Depressed factor correlated positively with the accuracy to recognize fearful expressions (r=.473). For the MES group fear recognition correlated positively with negative PANSS factor (r=.498) and recognition of sad and neutral expressions was inversely correlated with disorganized PANSS factor (r=-.461 and r=-.541, respectively). These results provide evidence that a generalized impairment of affect recognition is observed in advanced-stage patients and is not characteristic of the early stages of schizophrenia. Moreover, the finding that anomalous attribution of emotional meaning to neutral faces is observed only in MES patients suggests that an increased attribution of salience to social stimuli is a characteristic of social cognition in advanced stages of the disorder. Copyright © 2016 Elsevier B.V. All rights reserved.

Determinants of duration of untreated psychosis among first-episode psychosis patients in Denmark: A nationwide register-based study.

PubMed

Hastrup, Lene Halling; Haahr, Ulrik Helt; Jansen, Jens Einar; Simonsen, Erik

2018-02-01

Information on determinants of duration of untreated psychosis (DUP) is still needed to inform campaigns targeting people with first episode psychosis (FEP). This nation-wide study analysed the association between demographic factors (age, sex, ethnicity, marital status, and geographic area), premorbid and illness-related factors (global functional level, substance misuse, and contact to police), healthcare factors (referral source and first FEP contact) and DUP. The study population of 1266 patients aged 15-25years diagnosed with FEP (ICD10 F20.0-F20.99) was drawn from the Danish National Indicator Project during 2009-2011. The study population was combined with data from national administrative registers. A multinomial regression model was estimated to analyse the impact of demographic, premorbid and illness-related, and healthcare factors on DUP. One third of the population had a DUP below 6months. DUP longer than 12months was associated with older age at onset, being female, having cannabis misuse, and living in peripheral municipalities. Being charged by the criminal authorities during one year before FEP was associated with a DUP over 6months. DUP is related to a number of demographic, premorbid and healthcare factors. These findings suggest that future information campaigns should focus on increasing the awareness of early signs of psychosis not only among mental health professionals but also other professionals in contact with adolescents such as the police. It may also be useful to consider how to target information campaigns towards persons living in peripheral areas. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of Annealing on Mechanical Properties and Formability of Cold Rolled Thin Sheets of Fe-P P/M Alloys

NASA Astrophysics Data System (ADS)

Trivedi, Shefali; Ravi Kumar, D.; Aravindan, S.

2016-10-01

Phosphorus in steel is known to increase strength and hardness and decrease ductility. Higher phosphorus content (more than 0.05%), however, promotes brittle behavior due to segregation of Fe3P along the grain boundaries which makes further mechanical working of these alloys difficult. In this work, thin sheets of Fe-P alloys (with phosphorus in range of 0.1-0.35%) have been developed through processing by powder metallurgy followed by hot rolling and cold rolling. The effect of phosphorus content and annealing parameters (temperature and time) on microstructure, mechanical properties, formability in biaxial stretching and fracture behavior of the cold rolled and annealed sheets has been studied. A comparison has also been made between the properties of the sheets made through P/M route and the conventional cast route with similar phosphorus content. It has been shown that thin sheets of Fe-P alloys with phosphorous up to 0.35% possessing a good combination of strength and formability can be produced through rolling of billets of these alloys made through powder metallurgy technique without the problem of segregation.

[Questionnaire on parental attitudes and rearing practices (FEPS)].

PubMed

Richter-Appelt, Hertha; Schimmelmann, Benno Graf; Tiefensee, Jutta

2004-01-01

A positive parent-child relationship is one of the most important determinants of a healthy cognitive, emotional and social development. The relationship from parent to child is determined by parenting styles. Parenting styles are characterised by the two dimensions parental attitudes and rearing practices. The development and the psychometric properties of a questionnaire on parental attitudes and rearing practices (FEPS), which contains an extended version of the Parental Bonding Instrument by Parker et al. (PBI, 1979) and two scales on parental reinforcement and punishment behaviour, is presented. In a sample of 457 women and 159 men factorial and item analysis revealed four scales (care, autonomy, low punishment and low material reinforcement). The care dimension contained items of immaterial reinforcement on the positive pole and items of coldness and ignorance as means of punishment on the negative pole. Based on findings from its first application in a clinical study it can be assumed that the FEPS differentiates between clinical and non-clinical populations. Additionally, varying patterns of the four scales may emerge as risk factors for the development of certain psychiatric/psychological problems.

Template-based fluoroethylenepropylene piezoelectrets with tubular channels for transducer applications

NASA Astrophysics Data System (ADS)

Altafim, Ruy Alberto Pisani; Qiu, Xunlin; Wirges, Werner; Gerhard, Reimund; Altafim, Ruy Alberto Corrêa; Basso, Heitor Cury; Jenninger, Werner; Wagner, Joachim

2009-07-01

We describe the concept, the fabrication, and the most relevant properties of a piezoelectric-polymer system: Two fluoroethylenepropylene (FEP) films with good electret properties are laminated around a specifically designed and prepared polytetrafluoroethylene (PTFE) template at 300 °C. After removing the PTFE template, a two-layer FEP film with open tubular channels is obtained. For electric charging, the two-layer FEP system is subjected to a high electric field. The resulting dielectric barrier discharges inside the tubular channels yield a ferroelectret with high piezoelectricity. d33 coefficients of up to 160 pC/N have already been achieved on the ferroelectret films. After charging at suitable elevated temperatures, the piezoelectricity is stable at temperatures of at least 130 °C. Advantages of the transducer films include ease of fabrication at laboratory or industrial scales, a wide range of possible geometrical and processing parameters, straightforward control of the uniformity of the polymer system, flexibility, and versatility of the soft ferroelectrets, and a large potential for device applications e.g., in the areas of biomedicine, communications, production engineering, sensor systems, environmental monitoring, etc.

Crystal structures and optical properties of new quaternary strontium europium aluminate luminescent nanoribbons

DOE PAGES

Li, Xufan; Budai, John D.; Liu, Feng; ...

2014-11-12

We report the synthesis and characterizations of three series of quaternary strontium europium aluminate (Sr-Eu-Al-O; SEAO) luminescent nanoribbons that show blue, green, and yellow luminescence from localized Eu2+ luminescent centers. These three series of SEAO nanoribbons are: blue luminescent, tetragonal Sr1-xEuxAl6O10 (01-xEu xAl 2O 4 (01-xEu xAl 2O 4 (0

Development of High Temperature Superconducting Josephson Junction Device Technology

DTIC Science & Technology

1998-07-09

neodymium gallate , cerium oxide-buffered sapphire, and lanthanum aluminate, are not ideal for an in situ thallium cuprate junction technology. Moreover...determined that the standard HTS substrates, neodymium gallate , cerium oxide-buffered sapphire, and lanthanum aluminate, are not ideal for an in situ...2.2.1. Deposition Uniformity 10 2.2.2. Radiative Element 12 2.3. SUBSTRATES 13 2.3.1. Neodymium gallate 14 2.3.2. Cerium Oxide-Buffered Sapphire 16

Eigenvalue Detonation of Combined Effects Aluminized Explosives

NASA Astrophysics Data System (ADS)

Capellos, Christos; Baker, Ernest; Balas, Wendy; Nicolich, Steven; Stiel, Leonard

2007-06-01

This paper reports on the development of theory and performance for recently developed combined effects aluminized explosives. Traditional high energy explosives used for metal pushing incorporate high loading percentages of HMX or RDX, whereas blast explosives incorporate some percentage of aluminum. However, the high blast explosives produce increased blast energies, with reduced metal pushing capability due to late time aluminum reaction. Metal pushing capability refers to the early volume expansion work produced during the first few volume expansions associated with cylinder wall velocities and Gurney energies. Our Recently developed combined effects aluminized explosives (PAX-29C, PAX-30, PAX-42) are capable of achieving excellent metal pushing and high blast energies. Traditional Chapman-Jouguet detonation theory does not explain the observed detonation states achieved by these combined effects explosives. This work demonstrates, with the use of cylinder expansion data and thermochemical code calculations (JAGUAR and CHEETAH), that eigenvalue detonation theory explains the observed behavior.

Study of photoluminescence properties of CaAl{sub 2}O{sub 4}: Eu{sup 2+} prepared by combustion synthesis method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hingwe, V. S., E-mail: vishwas.hingwe@yahoo.in; Omanwar, S. K.; Bajaj, N. S.

2016-05-06

Eu{sup 2+} doped alkaline earth metals such as strontium aluminate, calcium aluminate and barium aluminate prepared by using modified combustion synthesis method at 600°C with Urea as fuel. Crystal structure is determined by using XRD and the sample confirmation by using the FTIR. The effect of the host material on the photoluminescence (PL) and phosphorescence properties were studied by using the Hitachi F-7000 spectrofluorimeter equipped with a 450W Xenon lamp, in the range 200-650 nm. The emission spectra of Eu{sup 2+} range from 450 to 500 nm in the Blue to aqua region and the transition 4f{sup 7}-4f{sup 6} 5d{sup 1}.more » The observed emission in CaAl{sub 2}O{sub 4} is 440 nm.« less

Spacecraft outer thermal blankets as hypervelocity impact bumpers

NASA Astrophysics Data System (ADS)

Cour-Palais, B. G.

1996-05-01

A thermal barrier consisting of a woven fabric outer layer followed by several layers of aluminized mylar insulation has been the primary impact protection against micrometeoroid and orbital impacts for many spacecraft currently in orbit. This paper examines its effectiveness as a hypervelocity "bumper" based on the performance of a NASA space suit. In this case, the thermal barrier consisted of a fabric layer followed by five layers of the aluminized mylar, which shielded either an aluminum rear wall or a rubberized pressure garment. The total areal density of the fabric and mylar layers was 0.052 g/cm2 and the fabric stand-off was 4 mm from the protected surfaces, with the aluminized mylar filling the space. Test results obtained with hypervelocity aluminum projectile impacts up to 8.5 km/s on the thermal barrier and aluminum wall are described, and a semi-empirical equation for this type of shielding is suggested.

Method of processing aluminous ores

DOEpatents

Loutfy, Raouf O.; Keller, Rudolf; Yao, Neng-Ping

1981-01-01

A method of producing aluminum chloride from aluminous materials containing compounds of iron, titanium and silicon comprising reacting the aluminous materials with carbon and a chlorine-containing gas at a temperature of about 900.degree. K. to form a gaseous mixture containing chlorides of aluminum, iron, titanium and silicon and oxides of carbon; cooling the gaseous mixture to a temperature of about 400.degree. K. or lower to condense the aluminum chlorides and iron chlorides while titanium chloride and silicon chloride remain in the gas phase to effect a separation thereof; heating the mixture of iron chlorides and aluminum chlorides to a temperature of about 800.degree. K. to form gaseous aluminum chlorides and iron chlorides; passing the heated gases into intimate contact with aluminum sulfide to precipitate solid iron sulfide and to form additional gaseous aluminum chlorides; and separating the gaseous aluminum chloride from the solid iron sulfide.

Single Common Powertrain Lubricant (SCPL) Development. Part 2

DTIC Science & Technology

2014-04-01

stand and connected via steel braided Teflon hose to the engines oil filter outlet port. A remote liquid-liquid heat exchanger was then added in...series with the stainless braided Teflon oil lines (after the oil filter), and its return was plumbed back to the engine via the engine’s front lower

78 FR 14934 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-08

... discrepancies of the wiring and surrounding Teflon sleeves of the fuel tank boost pumps and override/jettison... the wiring and sleeves with new parts, as necessary. The first SNPRM proposed to reduce the initial... inspections to detect discrepancies of the wiring and surrounding Teflon sleeves of the fuel tank boost pumps...

Fluorescence High-Throughput Screening for Inhibitors of TonB Action.

PubMed

Nairn, Brittany L; Eliasson, Olivia S; Hyder, Dallas R; Long, Noah J; Majumdar, Aritri; Chakravorty, Somnath; McDonald, Peter; Roy, Anuradha; Newton, Salete M; Klebba, Phillip E

2017-05-15

Gram-negative bacteria acquire ferric siderophores through TonB-dependent outer membrane transporters (TBDT). By fluorescence spectroscopic hgh-throughput screening (FLHTS), we identified inhibitors of TonB-dependent ferric enterobactin (FeEnt) uptake through Escherichia coli FepA (EcoFepA). Among 165 inhibitors found in a primary screen of 17,441 compounds, we evaluated 20 in secondary tests: TonB-dependent ferric siderophore uptake and colicin killing and proton motive force-dependent lactose transport. Six of 20 primary hits inhibited TonB-dependent activity in all tests. Comparison of their effects on [ 59 Fe]Ent and [ 14 C]lactose accumulation suggested several as proton ionophores, but two chemicals, ebselen and ST0082990, are likely not proton ionophores and may inhibit TonB-ExbBD. The facility of FLHTS against E. coli led us to adapt it to Acinetobacter baumannii We identified its FepA ortholog (AbaFepA), deleted and cloned its structural gene, genetically engineered 8 Cys substitutions in its surface loops, labeled them with fluorescein, and made fluorescence spectroscopic observations of FeEnt uptake in A. baumannii Several Cys substitutions in AbaFepA (S279C, T562C, and S665C) were readily fluoresceinated and then suitable as sensors of FeEnt transport. As in E. coli , the test monitored TonB-dependent FeEnt uptake by AbaFepA. In microtiter format with A. baumannii , FLHTS produced Z' factors 0.6 to 0.8. These data validated the FLHTS strategy against even distantly related Gram-negative bacterial pathogens. Overall, it discovered agents that block TonB-dependent transport and showed the potential to find compounds that act against Gram-negative CRE (carbapenem-resistant Enterobacteriaceae) /ESKAPE ( Enterococcus faecium , Staphylococcus aureus , Klebsiella pneumoniae , Acinetobacter baumannii , Pseudomonas aeruginosa , and Enterobacter species) pathogens. Our results suggest that hundreds of such chemicals may exist in larger compound libraries. IMPORTANCE Antibiotic resistance in Gram-negative bacteria has spurred efforts to find novel compounds against new targets. The CRE/ESKAPE pathogens are resistant bacteria that include Acinetobacter baumannii , a common cause of ventilator-associated pneumonia and sepsis. We performed fluorescence high-throughput screening (FLHTS) against Escherichia coli to find inhibitors of TonB-dependent iron transport, tested them against A. baumannii , and then adapted the FLHTS technology to allow direct screening against A. baumannii This methodology is expandable to other drug-resistant Gram-negative pathogens. Compounds that block TonB action may interfere with iron acquisition from eukaryotic hosts and thereby constitute bacteriostatic antibiotics that prevent microbial colonization of human and animals. The FLHTS method may identify both species-specific and broad-spectrum agents against Gram-negative bacteria. Copyright © 2017 American Society for Microbiology.

Advancing Drug Discovery through Enhanced Free Energy Calculations.

PubMed

Abel, Robert; Wang, Lingle; Harder, Edward D; Berne, B J; Friesner, Richard A

2017-07-18

A principal goal of drug discovery project is to design molecules that can tightly and selectively bind to the target protein receptor. Accurate prediction of protein-ligand binding free energies is therefore of central importance in computational chemistry and computer aided drug design. Multiple recent improvements in computing power, classical force field accuracy, enhanced sampling methods, and simulation setup have enabled accurate and reliable calculations of protein-ligands binding free energies, and position free energy calculations to play a guiding role in small molecule drug discovery. In this Account, we outline the relevant methodological advances, including the REST2 (Replica Exchange with Solute Temperting) enhanced sampling, the incorporation of REST2 sampling with convential FEP (Free Energy Perturbation) through FEP/REST, the OPLS3 force field, and the advanced simulation setup that constitute our FEP+ approach, followed by the presentation of extensive comparisons with experiment, demonstrating sufficient accuracy in potency prediction (better than 1 kcal/mol) to substantially impact lead optimization campaigns. The limitations of the current FEP+ implementation and best practices in drug discovery applications are also discussed followed by the future methodology development plans to address those limitations. We then report results from a recent drug discovery project, in which several thousand FEP+ calculations were successfully deployed to simultaneously optimize potency, selectivity, and solubility, illustrating the power of the approach to solve challenging drug design problems. The capabilities of free energy calculations to accurately predict potency and selectivity have led to the advance of ongoing drug discovery projects, in challenging situations where alternative approaches would have great difficulties. The ability to effectively carry out projects evaluating tens of thousands, or hundreds of thousands, of proposed drug candidates, is potentially transformative in enabling hard to drug targets to be attacked, and in facilitating the development of superior compounds, in various dimensions, for a wide range of targets. More effective integration of FEP+ calculations into the drug discovery process will ensure that the results are deployed in an optimal fashion for yielding the best possible compounds entering the clinic; this is where the greatest payoff is in the exploitation of computer driven design capabilities. A key conclusion from the work described is the surprisingly robust and accurate results that are attainable within the conventional classical simulation, fixed charge paradigm. No doubt there are individual cases that would benefit from a more sophisticated energy model or dynamical treatment, and properties other than protein-ligand binding energies may be more sensitive to these approximations. We conclude that an inflection point in the ability of MD simulations to impact drug discovery has now been attained, due to the confluence of hardware and software development along with the formulation of "good enough" theoretical methods and models.

43. Cognitive Functioning in First-Episode Psychosis:_x000B_ Comparison of a 2-Year Coordinated Specialty Care Program to Community Care

PubMed Central

Schooler, Nina; Khan, Anzalee; Keefe, Richard; Robinson, Delbert; Kane, John

2017-01-01

Abstract Background: Significant cognitive impairment is already seen in first-episode psychosis (FEP) and degree of impairment is a moderator of long-term outcomes. Does specialized FEP treatment improve cognitive functioning? The NIMH sponsored RAISE-ETP study allows comparison of NAVIGATE, a coordinated specialty care intervention designed for FEP, to Community Care (CC) in a randomized clinical trial. (RCT) Methods: The RCT was conducted at 34 sites in the United States. Seventeen sites were randomly assigned to provide NAVIGATE and 17 to provide CC. Four hundred four consenting participants age 15 to 45 years old, experiencing an FEP and had not received more than 6 months of antipsychotic medication entered the study. Treatment and assessment continued for up to two years. The Brief Assessment of Cognition in Schizophrenia (BACS) was administered at baseline, one and two years. Age and sex adjusted T-scores for the BACS Composite and six sub-tests (Verbal Memory, Digit Sequencing, Verbal Fluency, Token Motor, Symbol Coding and Tower of London) were calculated. Generalized estimating equations (GEEs) were applied to compare change in treatments between baseline, months 12 and 24 adjusting for within and between site variation. Results: The NAVIGATE and CC groups included 221 and 181 participants. The Group X Visit interactions was a statistically significant predictor of change in: Verbal Memory, Verbal Fluency, Symbol Coding, Tower of London and the Composite (P < .001 for all). For the NAVIGATE group, there was significant improvement at Month 12 and Month 24 for Verbal Memory, Digit Sequencing, Tower of London, and the Composite. For the CC group, there was a significant improvement at Month 12 and Month 24 for the Composite; and only at month 24 for the Tower of London. Conclusion: The results of this analysis suggest that NAVIGATE resulted in greater improvement in cognitive functioning in both an overall score and for specific components than did CC. NAVIGATE is a multi-component intervention, guided by manuals and supervision by a central team. NAVIGATE includes psychopharmacological treatment with antipsychotics and other psychotropic medications using an internet based decision support system, an individual psychotherapy called Individual Resiliency Training, family psychoeducation and supported employment and education. The role of individual components cannot be readily determined and further analyses will evaluate the effect of moderator variables such as duration of untreated psychosis, symptomatology and functioning at study entry. To date, pharmacologic treatments to improve cognition have not demonstrated efficacy. Cognitive remediation strategies, notably Cognitive Enhancement Therapy pioneered by Gerard Hogarty, has shown efficacy in FEP patients but to the best of our knowledge, this is the first RCT to show an effect of a broad FEP focused intervention on cognitive functioning.

[How do metallic middle ear implants behave in the MRI?].

PubMed

Kwok, P; Waldeck, A; Strutz, J

2003-01-01

Magnetic resonance imaging (MRI) has gained in frequency and importance as a diagnostic procedure. In respect to the close anatomical relationship in the temporal bone it is necessary to know whether it is hazardous to patients with metallic middle ear implants regarding displacement and rise in temperature. For the MR image quality artefacts caused by metallic prostheses should be low. Four different stapes prostheses made from titanium, gold, teflon/platinum and teflon/steel, a titanium total ossicular reconstruction prosthesis (TORP) and two ventilation tubes (made from titanium and gold) were tested in a 1.5 Tesla MRI machine regarding their displacement. All objects were first placed in a petri dish, then suspended from a thread and finally immersed in a dish filled with Gadolinium. Temperature changes of the implants were recorded by a pyrometer. None of the implants moved when they were placed in the petri dish or suspended from the thread. On the water surface the teflon/platinum and the teflon/steel pistons adjusted their direction with their axis longitudinally to the MRI scanner opening and the teflon/steel piston floated towards the MRI-machine when put close enough to the scanner opening. No rise in temperature was recorded. All implants showed as little artefacts that would still make an evaluation of the surrounding tissue possible. Patients with any of the metallic middle ear implants that were examined in this study may undergo MRI-investigations without significant adverse effects.

Shrinkage vectors of a flowable composite in artificial cavity models with different boundary conditions: Ceramic and Teflon.

PubMed

Kaisarly, Dalia; El Gezawi, Moataz; Xu, Xiaohui; Rösch, Peter; Kunzelmann, Karl-Heinz

2018-01-01

Polymerization shrinkage of dental resin composites leads to stress build-up at the tooth-restoration interface that predisposes the restoration to debonding. In contrast to the heterogeneity of enamel and dentin, this study investigated the effect of boundary conditions in artificial cavity models such as ceramic and Teflon. Ceramic serves as a homogenous substrate that provides optimal bonding conditions, which we presented in the form of etched and silanized ceramic in addition to an etched, silanized and bonded ceramic cavity. In contrast, the Teflon cavity presented a non-adhesive boundary condition that provided an exaggerated condition of poor bonding as in the case of contamination during the application procedure or a poor bonding substrate such as sclerotic or deep dentin. The greatest 3D shrinkage vectors and movement in the axial direction were observed in the ceramic cavity with the bonding agent followed by the silanized ceramic cavity, and smallest shrinkage vectors and axial movements were observed in the Teflon cavity. The shrinkage vectors in the ceramic cavities exhibited downward movement toward the cavity bottom with great downward shrinkage of the free surface. The shrinkage vectors in the Teflon cavity pointed towards the center of the restoration with lateral movement greater at one side denoting the site of first detachment from the cavity walls. These results proved that the boundary conditions, in terms of bonding substrates, significantly influenced the shrinkage direction. Copyright © 2017 Elsevier Ltd. All rights reserved.

Monolithic Teflon membrane valves and pumps for harsh chemical and low-temperature use.

PubMed

Willis, Peter A; Hunt, Brian D; White, Victor E; Lee, Michael C; Ikeda, Michael; Bae, Sam; Pelletier, Michael J; Grunthaner, Frank J

2007-11-01

Microfluidic diaphragm valves and pumps capable of surviving conditions required for unmanned spaceflight applications have been developed. The Pasteur payload of the European ExoMars Rover is expected to experience temperatures ranging between -100 degrees C and +50 degrees C during its transit to Mars and on the Martian surface. As such, the Urey instrument package, which contains at its core a lab-on-a-chip capillary electrophoresis analysis system first demonstrated by Mathies et al., requires valving and pumping systems that are robust under these conditions before and after exposure to liquid samples, which are to be analyzed for chemical signatures of past or present living processes. The microfluidic system developed to meet this requirement uses membranes consisting of Teflon and Teflon AF as a deformable material in the valve seat region between etched Borofloat glass wafers. Pneumatic pressure and vacuum, delivered via off-chip solenoid valves, are used to actuate individual on-chip valves. Valve sealing properties of Teflon diaphragm valves, as well as pumping properties from collections of valves, are characterized. Secondary processing for embossing the membrane against the valve seats after fabrication is performed to optimize single valve sealing characteristics. A variety of different material solutions are found to produce robust devices. The optimal valve system utilizes a membrane of mechanically cut Teflon sandwiched between two thin spun films of Teflon AF-1600 as a composite "laminated" diaphragm. Pump rates up to 1600 nL s(-1) are achieved with pumps of this kind. These high pumping rates are possible because of the very fast response of the membranes to applied pressure, enabling extremely fast pump cycling with relatively small liquid volumes, compared to analogous diaphragm pumps. The developed technologies are robust over extremes of temperature cycling and are applicable in a wide range of chemical environments.

The effect of ozone on nicotine desorption from model surfaces:evidence for heterogeneous chemistry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Destaillats, Hugo; Singer, Brett C.; Lee, Sharon K.

Assessment of secondhand tobacco smoke exposure using nicotine as a tracer or biomarker is affected by sorption of the alkaloid to indoor surfaces and by its long-term re-emission into the gas phase. However, surface chemical interactions of nicotine have not been sufficiently characterized. Here, the reaction of ozone with nicotine sorbed to Teflon and cotton surfaces was investigated in an environmental chamber by monitoring nicotine desorption over a week following equilibration in dry or humid air (65-70 % RH). The Teflon and cotton surfaces had N{sub 2}-BET surface areas of 0.19 and 1.17 m{sup 2} g{sup -1}, and water massmore » uptakes (at 70 % RH) of 0 and 7.1 % respectively. Compared with dry air baseline levels in the absence of O{sub 3}, gas phase nicotine concentrations decrease, by 2 orders of magnitude for Teflon after 50 h at 20-45 ppb O{sub 3}, and by a factor of 10 for cotton after 100 h with 13-15 ppb O{sub 3}. The ratios of pseudo first-order rate constants for surface reaction (r) to long-term desorption (k) were r/k = 3.5 and 2.0 for Teflon and cotton surfaces, respectively. These results show that surface oxidation was competitive with desorption. Hence, oxidative losses could significantly reduce long-term re-emissions of nicotine from indoor surfaces. Formaldehyde, N-methylformamide, nicotinaldehyde and cotinine were identified as oxidation products, indicating that the pyrrolidinic N was the site of electrophilic attack by O{sub 3}. The presence of water vapor had no effect on the nicotine-O{sub 3} reaction on Teflon surfaces. By contrast, nicotine desorption from cotton in humid air was unaffected by the presence of ozone. These observations are consistent with complete inhibition of ozone-nicotine surface reactions in an aqueous surface film present in cotton but not in Teflon surfaces.« less

Pulmonary effects induced by ultrafine PTFE particles.

PubMed

Johnston, C J; Finkelstein, J N; Mercer, P; Corson, N; Gelein, R; Oberdörster, G

2000-11-01

PTFE (polytetrafluoroethylene) fumes consisting of large numbers of ultrafine (uf) particles and low concentrations of gas-phase compounds can cause severe acute lung injury. Our studies were designed to test three hypotheses: (i) uf PTFE fume particles are causally involved in the induction of acute lung injury, (ii) uf PTFE elicit greater pulmonary effects than larger sized PTFE accumulation mode particles, and (iii) preexposure to the uf PTFE fume particles will induce tolerance. We used uf Teflon (PTFE) fumes (count median particle size approximately 16 nm) generated by heating PTFE in a tube furnace to 486 degrees C to evaluate principles of ultrafine particle toxicity. Teflon fumes at ultrafine particle concentrations of 50 microg/m(3) were extremely toxic to rats when inhaled for only 15 min. We found that when generated in argon, the ultrafine Teflon particles alone are not toxic at these exposure conditions; neither were Teflon fume gas-phase constituents when generated in air. Only the combination of both phases when generated in air caused high toxicity, suggesting either the existence of radicals on the surface or a carrier mechanism of the ultrafine particles for adsorbed gas compounds. Aging of the fresh Teflon fumes for 3.5 min led to a predicted coagulation to >100 nm particles which no longer caused toxicity in exposed animals. This result is consistent with a greater toxicity of ultrafine particles compared to accumulation mode particles, although changes in particle surface chemistry during the aging process may have contributed to the diminished toxicity. Furthermore, the pulmonary toxicity of the ultrafine Teflon fumes could be prevented by adapting the animals with short 5-min exposures on 3 days prior to a 15-min exposure. Messages encoding antioxidants and chemokines were increased substantially in nonadapted animals, yet were unaltered in adapted animals. This study shows the importance of preexposure history for the susceptibility to acute ultrafine particle effects. Copyright 2000 Academic Press.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bizzozero, Julien, E-mail: julien.bizzozero@gmail.com; Scrivener, Karen L.

This paper reports a study of ternary blends composed of calcium aluminate cement, calcium sulfate hemihydrate and limestone. Compressive strength tests and hydration kinetics were studied as a function of limestone and calcium sulfate content. The phase evolution and the total porosity were followed and compared to thermodynamic simulation to understand the reactions involved and the effect of limestone on these binders. The reaction of limestone leads to the formation of hemicarboaluminate and monocarboaluminate. Increasing the ratio between sulfate and aluminate decreases the extent of limestone reaction.

A Combined Brazing and Aluminizing Process for Repairing Turbine Blades by Thermal Spraying Using the Coating System NiCrSi/NiCoCrAlY/Al

NASA Astrophysics Data System (ADS)

Nicolaus, M.; Möhwald, K.; Maier, H. J.

2017-10-01

The repair and maintenance of components in the aerospace industry play an increasingly important role due to rising manufacturing costs. Besides welding, vacuum brazing is a well-established repair process for turbine blades made of nickel-based alloys. After the coating of the worn turbine blade has been removed, the manual application of the nickel-based filler metal follows. Subsequently, the hot gas corrosion-protective coating is applied by thermal spraying. The brazed turbine blade is aluminized to increase the hot gas corrosion resistance. The thermal spray technology is used to develop a two-stage hybrid technology that allows shortening the process chain for repair brazing turbine blades and is described in the present paper. In the first step, the coating is applied on the base material. Specifically, the coating system employed here is a layer system consisting of nickel filler metal, NiCoCrAlY and aluminum. The second step represents the combination of brazing and aluminizing of the coating system which is subjected to a heat treatment. The microstructure, which results from the combined brazing and aluminizing process, is characterized and the relevant diffusion processes in the coating system are illustrated. The properties of the coating and the ramifications with respect to actual applications will be discussed.

Towards the nonstick egg: designing fluorous proteins.

PubMed

Neil, E; Marsh, G

2000-07-01

Anyone who has made scrambled eggs will have had cause to praise the properties of Teflon. Teflon's highly chemically inert and nonstick nature derives from the perfluorinated polymer polytetrafluoroethylene. Perfluorocarbons have unique and valuable physical properties not found in nature. By incorporating fluorine into proteins, it might be possible to produce biological molecules with novel and useful properties.

Dimensional scaling for impact cratering and perforation

NASA Technical Reports Server (NTRS)

Watts, Alan; Atkinson, Dale; Rieco, Steve

1993-01-01

This report summarizes the development of two physics-based scaling laws for describing crater depths and diameters caused by normal incidence impacts into aluminum and TFE Teflon. The report then describes equations for perforations in aluminum and TFE Teflon for normal impacts. Lastly, this report also studies the effects of non-normal incidence on cratering and perforation.

Seeking help for first-episode psychosis: a family narrative.

PubMed

Connor, Charlotte; Greenfield, Sheila; Lester, Helen; Channa, Sunita; Palmer, Colin; Barker, Clare; Lavis, Anna; Birchwood, Max

2016-08-01

Delayed help-seeking can have serious consequences for young people with first-episode psychosis (FEP), in terms of treatment response and outcome. Young people's narratives about help-seeking are important to understand why delays occur; however, as the majority of help-seeking is initiated by family members, through a general practitioner (GP), family narratives are also of interest. The aim of this study was to explore help-seeking for FEP, including first contact with a GP. A semistructured interview was developed using a topic guide. Framework analysis was used to analyse data and a deductive qualitative method for applied research. The study was set in Birmingham, UK. Participants were interviewed separately by researchers. Joint coding and identification of 14 complete family dyads was then explored for emerging patterns within the family context. Family responses to FEP that had an impact on help-seeking behaviour included withdrawal, normalization, stigma, fear and guilt; poor knowledge of availability, and means of access to mental health services was also important. Help-seeking was usually instigated by a family member through a GP, although this was not the case for two of our families, and while contact with GP was generally described as a positive experience for several families, it was hindered by poor communication and lack of engagement. Families play a key role in facilitating help-seeking for FEP, but attempts are often derailed by complex family responses to illness. Public mental health interventions should focus on increasing community awareness of psychosis and improving access and alternative routes to mental health services. However, improvements will have little impact unless primary care and other help-seeking sources engage in open and easy dialogue with the families and young people trying to access their specialist services. © 2014 Wiley Publishing Asia Pty Ltd.

The prognostic value of formal thought disorder following first episode psychosis.

PubMed

Roche, Eric; Lyne, John; O'Donoghue, Brian; Segurado, Ricardo; Behan, Caragh; Renwick, Laoise; Fanning, Felicity; Madigan, Kevin; Clarke, Mary

2016-12-01

Formal thought disorder (FTD) is associated with poor outcome in established psychotic illnesses and it can be assessed as a categorical or dimensional variable. However, its influence on functional outcome and hospitalisation patterns in early psychosis has not been investigated. We evaluated the relationship between FTD and these outcomes in a first episode psychosis (FEP) sample. A mixed diagnostic FEP cohort was recruited through an Early Intervention in Psychosis Service in Ireland. Participants were assessed at initial presentation and one year later with the MIRECC GAF to evaluate social and occupational functioning domains. Disorganisation (disFTD), verbosity (verFTD) and poverty (povFTD) dimensions of FTD were examined at both time points, as well as a unitary FTD construct. Analyses were controlled for demographic, clinical and treatment variables. DisFTD was the only FTD dimension associated with functional outcome, specifically social functioning, on multivariate analysis (beta=0.13, P<0.05). The unitary FTD construct was not associated with functional outcome. DisFTD at FEP presentation predicted a greater number of hospitalisations (adjusted beta=0.24, P<0.001) and prolonged inpatient admission (adjusted OR=1.08, 95% CI 1.02-1.15, P<0.05) following FEP. Longitudinal and dimensional evaluation of FTD has a clinical utility that is distinct from a cross-sectional or unitary assessment. Dimensions of FTD may map onto different domains of functioning. These findings are supportive of some of the changes in DSM-V with an emphasis on longitudinal and dimensional appraisal of psychopathology. Communication disorders may be considered a potential target for intervention in psychotic disorders. Copyright © 2016 Elsevier B.V. All rights reserved.

Social inclusion and its interrelationships with social cognition and social functioning in first-episode psychosis.

PubMed

Gardner, Andrew; Cotton, Sue M; Allott, Kelly; Filia, Kate M; Hester, Robert; Killackey, Eóin

2017-10-27

People with psychosis are at risk of social exclusion. Research is needed in this area due to the lack of direct measurement of social inclusion, which becomes salient in adolescence and is relevant to first-episode psychosis (FEP; the onset of which typically occurs during or shortly after adolescence). Social inclusion may be impacted by impaired social cognition and social functioning, which are related features observed in psychosis. The aim of this study was to explore interrelationship(s) between social cognition, social functioning and social inclusion in FEP while controlling for symptomatology (positive, negative and depressive symptoms) and demographic characteristics. A series of cross-sectional hierarchical multiple regressions were conducted to examine whether: social cognition (theory of mind, emotion recognition) predicted social functioning; social functioning predicted social inclusion, and whether social functioning mediated the relationship between social cognition and social inclusion in people aged 15 to 25 (M = 20.49, SD = 2.41) with FEP (N = 146). Age, sex, premorbid IQ, positive and negative psychotic symptoms and depression were control variables. Poor facial emotion recognition (β = -.22, P < .05) and negative symptoms (β = -.45, P < .001) predicted lower social functioning. Role-specific social functioning (ie, current employment) predicted greater social inclusion (β = .17, P < .05). Higher depression symptomatology predicted lower social inclusion (β = -.43, P < .001). Social functioning did not mediate the relationship between social cognition and inclusion. Psychotic symptoms were unrelated to social inclusion. Employment and depression may influence social inclusion somewhat independently of psychotic symptomatology in FEP. Inferences should be viewed with caution given this study did not involve longitudinal data. © 2017 John Wiley & Sons Australia, Ltd.

Gray and white matter changes and their relation to illness trajectory in first episode psychosis.

PubMed

Keymer-Gausset, Alejandro; Alonso-Solís, Anna; Corripio, Iluminada; Sauras-Quetcuti, Rosa B; Pomarol-Clotet, Edith; Canales-Rodriguez, Erick J; Grasa-Bello, Eva; Álvarez, Enric; Portella, Maria J

2018-03-01

Previous works have studied structural brain characteristics in first-episode psychosis (FEP), but few have focused on the relation between brain differences and illness trajectories. The aim of this study is to analyze gray and white matter changes in FEP patients and their relation with one-year clinical outcomes. A sample of 41 FEP patients and 41 healthy controls (HC), matched by age and educational level was scanned with a 3T MRI during the first month of illness onset. One year later, patients were assigned to two illness trajectories (schizophrenia and non-schizophrenia). Voxel-based morphometry (VBM) was used for gray matter and Tract-based spatial statistics (TBSS) was used for white matter data analysis. VBM revealed significant and widespread bilateral gray matter density differences between FEP and HC groups in areas that included the right insular Cortex, the inferior frontal gyrus and orbito-frontal cortices, and segments of the occipital cortex. TBSS showed a significant lower fractional anisotropy (FA) in 8 clusters that included segments of the anterior thalamic radiation, the left body and forceps minor of corpus callosum, the right anterior segment of the inferior fronto-occipital fasciculus and the anterior segments of the cingulum. The sub-groups comparison revealed significant lower FA in the schizophrenia sub-group in two clusters: the anterior thalamic radiation and the anterior segment of left cingulum. These findings are coherent with previous morphology studies. The results suggest that gray and white matter abnormalities are present at early stages of the disease, and white matter differences may distinguish different illness prognosis. Copyright © 2018 Elsevier B.V. and ECNP. All rights reserved.

Exercise effects on cognitive functioning in young adults with first-episode psychosis: FitForLife.

PubMed

Hallgren, Mats; Skott, Maria; Ekblom, Örjan; Firth, Joseph; Schembri, Adrian; Forsell, Yvonne

2018-05-06

Exercise has mood-enhancing effects and can improve cognitive functioning, but the effects in first-episode psychosis (FEP) remain understudied. We examined the feasibility and cognitive effects of exercise in FEP. Multi-center, open-label intervention study. Ninety-one outpatients with FEP (mean age = 30 years, 65% male) received usual care plus a 12-week supervised circuit-training program, consisting of high-volume resistance exercises, aerobic training, and stretching. Primary study outcome was cognitive functioning assessed by Cogstate Brief Battery (processing speed, attention, visual learning, working memory) and Trailmaking A and B tasks (visual attention and task shifting). Within-group changes in cognition were assessed using paired sample t tests with effect sizes (Hedges' g) reported for significant values. Relationships between exercise frequency and cognitive improvement were assessed using analysis of covariance. Moderating effects of gender were explored with stratified analyses. Participants exercised on average 13.5 (s.d. = 11.7) times. Forty-eight percent completed 12 or more sessions. Significant post-intervention improvements were seen for processing speed, visual learning, and visual attention; all with moderate effect sizes (g = 0.47-0.49, p < 0.05). Exercise participation was also associated with a positive non-significant trend for working memory (p < 0.07). Stratified analyses indicated a moderating effect of gender. Positive changes were seen among females only for processing speed, visual learning, working memory, and visual attention (g = 0.43-0.69). A significant bivariate correlation was found between total training frequency and improvements in visual attention among males (r = 0.40, p < 0.05). Supported physical exercise is a feasible and safe adjunct treatment for FEP with potential cognitive benefits, especially among females.

Brain bioenergetics and redox state measured by 31P magnetic resonance spectroscopy in unaffected siblings of patients with psychotic disorders.

PubMed

Chouinard, Virginie-Anne; Kim, Sang-Young; Valeri, Linda; Yuksel, Cagri; Ryan, Kyle P; Chouinard, Guy; Cohen, Bruce M; Du, Fei; Öngür, Dost

2017-09-01

Brain bioenergetic anomalies and redox dysregulation have been implicated in the pathophysiology of psychotic disorders. The present study examined brain energy-related metabolites and the balance between nicotinamide adenine dinucleotide metabolites (oxidized NAD+ and reduced NADH) using 31 P-magnetic resonance spectroscopy ( 31 P-MRS) in unaffected siblings, compared to first episode psychosis (FEP) patients and healthy controls. 21 unaffected siblings, 32 FEP patients (including schizophrenia spectrum and affective psychoses), and 21 controls underwent 31 P-MRS in the frontal lobe (6×6×4cm 3 ) on a 4T MR scanner, using custom-designed dual-tuned surface coil with outer volume suppression. Brain parenchymal pH and steady-state metabolite ratios of high energy phosphate compounds were measured. NAD+ and NADH levels were determined using a 31 P-MRS fitting algorithm. 13 unaffected sibling-patient pairs were related; other patients and siblings were unrelated. ANCOVA analyses were used to examine 31 P-MRS measures, with age and gender as covariates. The phosphocreatine/adenosine triphosphate ratio was significantly reduced in both unaffected siblings and FEP patients, compared to controls. NAD+/NADH ratio was significantly reduced in patients compared to siblings and controls, with siblings showing a reduction in NAD+/NADH compared to controls that was not statistically significant. Compared to patients and controls, siblings showed significantly reduced levels of NAD+. Siblings did not differ from patients or controls on brain pH. Our results indicate that unaffected siblings show some, but not all the same abnormalities in brain energy metabolites and redox state as FEP patients. Thus, 31 P-MRS studies may identify factors related both to risk and expression of psychosis. Copyright © 2017 Elsevier B.V. All rights reserved.

Impaired action self-monitoring and cognitive confidence among ultra-high risk for psychosis and first-episode psychosis patients.

PubMed

Gawęda, Ł; Li, E; Lavoie, S; Whitford, T J; Moritz, S; Nelson, B

2018-01-01

Self-monitoring biases and overconfidence in incorrect judgments have been suggested as playing a role in schizophrenia spectrum disorders. Little is known about whether self-monitoring biases may contribute to early risk factors for psychosis. In this study, action self-monitoring (i.e., discrimination between imagined and performed actions) was investigated, along with confidence in judgments among ultra-high risk (UHR) for psychosis individuals and first-episode psychosis (FEP) patients. Thirty-six UHR for psychosis individuals, 25 FEP patients and 33 healthy controls (CON) participated in the study. Participants were assessed with the Action memory task. Simple actions were presented to participants verbally or non-verbally. Some actions were required to be physically performed and others were imagined. Participants were asked whether the action was presented verbally or non-verbally (action presentation type discrimination), and whether the action was performed or imagined (self-monitoring). Confidence self-ratings related to self-monitoring responses were obtained. The analysis of self-monitoring revealed that both UHR and FEP groups misattributed imagined actions as being performed (i.e., self-monitoring errors) significantly more often than the CON group. There were no differences regarding performed actions as being imagined. UHR and FEP groups made their false responses with higher confidence in their judgments than the CON group. There were no group differences regarding discrimination between the types of actions presented (verbal vs non-verbal). A specific type of self-monitoring bias (i.e., misattributing imagined actions with performed actions), accompanied by high confidence in this judgment, may be a risk factor for the subsequent development of a psychotic disorder. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Premorbid IQ subgroups in first episode non affective psychosis patients: Long-term sex differences in function and neurocognition.

PubMed

Ayesa-Arriola, Rosa; Setién-Suero, Esther; Neergaard, Karl David; Belzunces, Àuria Albacete; Contreras, Fernando; van Haren, Neeltje E M; Crespo-Facorro, Benedicto

2017-12-21

Low IQ has been associated with schizophrenia, even to the point of being posited as a possible causal factor for psychosis. However, individuals with normal and high IQ also develop psychotic illnesses. The aim of this study was to characterize premorbid IQ subgroups at first episode of psychosis (FEP). The study sample comes from a large epidemiological, 3-year longitudinal, intervention program on psychosis containing individuals living in a catchment area in Spain. Estimated premorbid IQ (epIQ) scores were used to build low (<90), normal (90-110) and high (>110) epIQ subgroups in samples of FEP patients (N=292) and healthy controls (N=199). The epIQ subgroups were compared in sociodemographic, neuropsychological, clinical and premorbid characteristics. Long-term functional and cognitive outcome, with a focus on sex differences, were also explored. Low-epIQ was more frequently found in FEP patients (28.8%) than in healthy controls (14.6%). Low-epIQ patients were more likely to have worse premorbid adjustment, belong to low socioeconomic status families, have less years of education, and to be single, unemployed, and younger. They presented more severe impairments in processing speed, executive and global cognitive function. Female patients with low-epIQ showed better baseline function and more stable outcome than males. Our results indicate that low premorbid IQ is a morbid manifestation, easily detected in a subgroup of FEP patients that predicts poorer outcome particularly in males. This perspective provides important information for the tailoring of subgroup-specific early intervention programs for psychosis. Copyright © 2017 Elsevier B.V. All rights reserved.

Phosphorus speciation and its bioavailability in sediments of the Jiaozhou Bay

NASA Astrophysics Data System (ADS)

Kang, Xuming; Song, Jinming; Yuan, Huamao; Shi, Xin; Yang, Weifeng; Li, Xuegang; Li, Ning; Duan, Liqin

2017-03-01

Phosphorus (P) is an important macronutrient that can limit primary productivity in coastal marine ecosystems. In this study, four sediment cores were collected in the Jiaozhou Bay to study the phosphorus forms and their bioavailability, including exchangeable or loosely sorbed P (Ex-P), iron-bound P (Fe-P), authigenic P (Ca-P), detrital P (De-P) and organic P (OP), which were separated and quantified using a sequential extraction method (SEDEX). The results showed that the concentration of total P (TP) in core sediments ranged from 6.23 to 10.46 μmol/g, and inorganic P (IP) was the dominated P form. Fe-P and De-P were the main chemical forms of IP in core sediments. The profile variation of OP presented the most significant among the phosphorus forms. Whereas the concentrations of Ex-P, Fe-P, and Ca-P varied slightly with depth, indicating that the transformation of Ex-P, Fe-P, Ca-P, and OP could occur during sedimentary P burial. Moreover, the distribution of P species was influenced by many factors, including terrigenous input, biological processes, organic matter degradation and increasing human activities. High total organic carbon (TOC)/OP ratio occurred in the Jiaozhou Bay, ranging from 73 to 472 (average, 180 ± 81) in core sediments, which was caused by the increasing terrestrial organic matter. The ratio of TOC/Preactive ranged from 24 to 101 (average 46 ± 15) in core sediments (lower than the Redfield ratio), implying a surplus of sedimentary reactive P compared with TOC. Potential bioavailable P (BAP) accounted for about 28.2-60.8% (average, 47.1 ± 7.4%) of TP in core sediments, and presented an increasing trend since 1980s, which might be responsible for the shift of phytoplankton community composition during these decades.

The Stability of Hydrous Silicates in Earth's Lower Mantle: Experimental constraints from the System MgO-Al2O3-SiO2-H2O

NASA Astrophysics Data System (ADS)

Walter, M. J.; Thomson, A. R.; Wang, W.; Lord, O. T.; Kleppe, A. K.; Ross, J.; Kohn, S. C.

2014-12-01

Laser-heated diamond anvil cell experiments were performed at pressures from ~ 30 to 125 GPa on bulk compositions in the system MgO-Al2O3-SiO2-H2O (MASH) to constrain the stability of hydrous phases in Earth's lower mantle. Phase identification in run products by synchrotron powder diffraction reveals a consistent set of stability relations for the high-pressure, dense hydrous silicate phases D and H. Experiments show that aluminous phase D is stable to ~ 55 GPa. Aluminous phase H becomes stable at ~ 40 GPa and remains stable to higher pressures throughout the lower mantle depth range in both model peridotitic and basaltic lithologies. Preliminary FEG-probe analyses indicate that Phase H is alumina-rich at ~ 50 GPa, with only 5 to 10 wt% each of MgO and SiO2. Variations in ambient unit cell volumes show that Mg-perovskite becomes more aluminous with pressure throughout the pressure range studied, and that Phase H may become more Mg- and Si-rich with pressure. We also find that at pressures above ~ 90 GPa stishovite is replaced in Si-rich compositions by seifertite, at which point there is a corresponding increase in the Al-content of phase H. The melting curves of MASH compositions have been determined using thermal perturbations in power versus temperature curves, and are observed to be shallow with dT/dP slopes of ~ 4K/GPa. Our results show that hydrated peridotitic or basaltic compositions in the lower mantle should be partially molten at all depths along an adiabatic mantle geotherm. Aluminous Phase H will be stable in colder, hydrated subducting slabs, potentially to the core-mantle boundary. Thus, aluminous phase H is the primary vessel for transport of hydrogen to the deepest mantle, but hydrous silicate melt will be the host of hydrogen at ambient mantle temperatures.

Boundary conditions for diffusion in the pack-aluminizing of nickel.

NASA Technical Reports Server (NTRS)

Sivakumar, R.; Seigle, L. L.; Menon, N. B.

1973-01-01

The surface compositions of nickel specimens coated for various lengths of time in aluminizing packs at 2000 F were studied, in order to obtain information about the kinetics of the pack-cementation process in the formation of aluminide coatings. The results obtained indicate that the surface compositions of the coated nickel specimens are independent of time, at least for time between 0.5 and 20 hrs. Another important observation is that the specimens gained weight during the coating process.

Thermodynamics and kinetics of reactions in protective coating systems

NASA Technical Reports Server (NTRS)

Gupta, B.; Sarkhel, A.; Shankar, S.; Seigle, L.

1975-01-01

A study of the aluminization of Ni from packs containing various percentages of unalloyed Al confirmed that the surface aluminum content of specimens aluminized tends to decrease with time and consequently a simple parabolic law for the weight-gain vs. time relationship is not obeyed. The diffusivity-composition relationship in NiAl was examined, and a set of curves is presented. A numerical method for the calculation of coating dissolution rates was developed and applied to NiAl-Ni3Al type of coatings.

Water-sensitive positron trapping modes in nanoporous magnesium aluminate ceramics

NASA Astrophysics Data System (ADS)

Filipecki, J.; Ingram, A.; Klym, H.; Shpotyuk, O.; Vakiv, M.

2007-08-01

The water-sensitive positron trapping modes in nanoporous MgAl2O4 ceramics with a spinel structure are studied. It is shown that water-sorption processes in magnesium aluminate ceramics leads to corresponding increase in positron trapping rates of extended defects located near intergranual boundaries. This catalytic affect has reversible nature, being strongly dependent on sorption water fluxes in ceramics. The fixation of all water-dependent positron trapping inputs allow to refine the most significant changes in positron trapping rate of extended defects.

Growth and Structure of Strontium Doped LaGaO3

DTIC Science & Technology

2001-01-01

Sandstrom, E.A. Giess, W.J. Gallagher, A. Segmifler, E.I. Cooper, M.F. Chisholm, A. Gupta, S. Shinole, R.B. Laibowitz," Lanthanum gallate substrates...that a structural phase transition occurs at -150 °C 5. The phase transition is the most serious drawback of many lanthanide gallates and aluminates5 for...and C.D. Brandle, "Thermal analysis of rare earth gallates and aluminates", J Mater. Res. 5, p. 183, 1990. 6. S. Miyazawa," Surface roughening

Space power plants

NASA Astrophysics Data System (ADS)

Khudyakov, S. A.

1985-05-01

Power generators in space are examined. A semiconducting photoelectric converter (FEP) which converts the energy of solar radiation directly into electrical energy is discussed. The operating principle of an FEP is based on the interaction of solar light with a crystal semiconductor, in the process of which the photons produce free electrons, carriers of an electrical charge, in the crystal. Areas with a strong electrical field created specially under the effect of the p-n junction trap the freed electrons and divide them in such a fashion that a current and corresponding electrical power appear in the load circuit. The absorption of light in metals and pure semiconductors is outlined.

Intrinsic motivation and amotivation in first episode and prolonged psychosis.

PubMed

Luther, Lauren; Lysaker, Paul H; Firmin, Ruth L; Breier, Alan; Vohs, Jenifer L

2015-12-01

The deleterious functional implications of motivation deficits in psychosis have generated interest in examining dimensions of the construct. However, there remains a paucity of data regarding whether dimensions of motivation differ over the course of psychosis. Therefore, this study examined two motivation dimensions, trait-like intrinsic motivation, and the negative symptom of amotivation, and tested the impact of illness phase on the 1) levels of these dimensions and 2) relationship between these dimensions. Participants with first episode psychosis (FEP; n=40) and prolonged psychosis (n=66) completed clinician-rated measures of intrinsic motivation and amotivation. Analyses revealed that when controlling for group differences in gender and education, the FEP group had significantly more intrinsic motivation and lower amotivation than the prolonged psychosis group. Moreover, intrinsic motivation was negatively correlated with amotivation in both FEP and prolonged psychosis, but the magnitude of the relationship did not statistically differ between groups. These findings suggest that motivation deficits are more severe later in the course of psychosis and that low intrinsic motivation may be partially independent of amotivation in both first episode and prolonged psychosis. Clinically, these results highlight the importance of targeting motivation in early intervention services. Copyright © 2015 Elsevier B.V. All rights reserved.

Minimum MD simulation length required to achieve reliable results in free energy perturbation calculations: case study of relative binding free energies of fructose-1,6-bisphosphatase inhibitors.

PubMed

Rathore, R S; Aparoy, P; Reddanna, P; Kondapi, A K; Reddy, M Rami

2011-07-30

In an attempt to establish the criteria for the length of simulation to achieve the desired convergence of free energy calculations, two studies were carried out on chosen complexes of FBPase-AMP mimics. Calculations were performed for varied length of simulations and for different starting configurations using both conventional- and QM/MM-FEP methods. The results demonstrate that for small perturbations, 1248 ps simulation time could be regarded a reasonable yardstick to achieve convergence of the results. As the simulation time is extended, the errors associated with free energy calculations also gradually tapers off. Moreover, when starting the simulation from different initial configurations of the systems, the results are not changed significantly, when performed for 1248 ps. This study carried on FBPase-AMP mimics corroborates well with our previous successful demonstration of requirement of simulation time for solvation studies, both by conventional and ab initio FEP. The establishment of aforementioned criteria of simulation length serves a useful benchmark in drug design efforts using FEP methodologies, to draw a meaningful and unequivocal conclusion. Copyright © 2011 Wiley Periodicals, Inc.

Flood Mapping in the Lower Mekong River Basin Using Daily MODIS Observations

NASA Technical Reports Server (NTRS)

Fayne, Jessica V.; Bolten, John D.; Doyle, Colin S.; Fuhrmann, Sven; Rice, Matthew T.; Houser, Paul R.; Lakshmi, Venkat

2017-01-01

In flat homogenous terrain such as in Cambodia and Vietnam, the monsoon season brings significant and consistent flooding between May and November. To monitor flooding in the Lower Mekong region, the near real-time NASA Flood Extent Product (NASA-FEP) was developed using seasonal normalized difference vegetation index (NDVI) differences from the 250 m resolution Moderate Resolution Imaging Spectroradiometer (MODIS) sensor compared to daily observations. The use of a percentage change interval classification relating to various stages of flooding reduces might be confusing to viewers or potential users, and therefore reducing the product usage. To increase the product usability through simplification, the classification intervals were compared with other commonly used change detection schemes to identify the change classification scheme that best delineates flooded areas. The percentage change method used in the NASA-FEP proved to be helpful in delineating flood boundaries compared to other change detection methods. The results of the accuracy assessments indicate that the -75% NDVI change interval can be reclassified to a descriptive 'flood' classification. A binary system was used to simplify the interpretation of the NASA-FEP by removing extraneous information from lower interval change classes.

Binding affinity of the L-742,001 inhibitor to the endonuclease domain of A/H1N1/PA influenza virus variants: Molecular simulation approaches

NASA Astrophysics Data System (ADS)

Nguyen, Hung; Nguyen, Hoang Linh; Linh, Huynh Quang; Nguyen, Minh Tho

2018-01-01

The steered molecular dynamics (SMD), molecular mechanics Poisson-Boltzmann surface area (MM-PBSA) and free energy perturbation (FEP) methods were used to determine the binding affinity of the L-742,001 inhibitor to the endonuclease domain of the A/H1N1/PA influenza viruses (including wild type (WT) and three mutations I79L, E119D and F105S for both pH1N1 PA and PR8 PA viruses). Calculated results showed that the L-742,001 inhibitor not only binds to the PR8 PAs (1934 A influenza virus) better than to the pH1N1 PAs (2009 A influenza virus) but also more strongly interacts with the WT endonuclease domain than with three mutant variants for both pH1N1 PA and PR8 PA viruses. The binding affinities obtained by the SMD, MM-PBSA and FEP methods attain high correlation with available experimental data. Here the FEP method appears to provide a more accurate determination of the binding affinity than the SMD and MM-PBSA counterparts.

Work life after psychosis: A detailed examination.

PubMed

Turner, Niall; O'Mahony, Paul; Hill, Michelle; Fanning, Felicity; Larkin, Conall; Waddington, John; O'Callaghan, Eadbhard; Clarke, Mary

2015-01-01

Conducting research on the work outcomes of first episode psychosis (FEP) samples may extend our understanding of the factors associated with the work outcome of people with schizophrenia and other psychotic illnesses. To conduct a detailed study of the work outcome of an FEP sample. Members of a FEP cohort, who had completed a 12-year clinical outcome assessment, were invited to participate in an adjunctive work outcome study. Engagement in paid and non-paid work was first established and the relationship with potentially influential baseline characteristics investigated. Subsequently the influence of work outcome to participants' level of quality of life, mental health, recovery, and social inclusion were examined. Among the 38 participants the mean percentage of time spent in work was 62% of which 50% was in paid work and 12% was in non-paid work. Being employed at inception was the only independent predictor of the duration of the follow-up period spent in work. Relationships between work outcome and all measures of wellbeing were found. The paid and non-paid work attained by people affected by a psychotic illness played an important role in the extent of their wellbeing, recovery, and social inclusion.

Use of cemented paste backfill in arsenic-rich tailings

NASA Astrophysics Data System (ADS)

Hamberg, Roger; Maurice, Christian; Alakangas, Lena

2015-04-01

Gold is extracted by cyanide leaching from inclusions in arsenopyrite from a mine in the north of Sweden. The major ore mineral assemblage consists of pyrrhotite and arsenopyrite-loellingite. Effluents from the gold extraction were treated with Fe2(SO4)3, with the aim to form stable As-bearing Fe-precipitates (FEP). The use of the method called cemented paste backfill (CPB) is sometimes suggested for the management of tailings. In CPB, tailings are commonly mixed with low proportions (3 - 7 %) of cement and backfilled into underground excavated area. To reduce costs, amendments such as granulated blast furnace slag (GBFS), biofuel fly ash (BFA) and cement kiln dust (CKD) are used for partial replacement of cement in CPB due to their pozzolanic and alkaline properties. The objective for this study was to evaluate the leaching behaviour of As in CPB-mixtures with low proportions (1 - 3 %) of BFA and ordinary cement and unmodified tailings. The selection of CPB-recipies was made based on technical and economical criterias to adress the demands deriving from the mining operations. Speciation of the As in ore and tailings samples revealed that mining processes have dissolved the majority of the arsenopyrite in the ore, causing secondary As phases to co-precipitate with newly formed FEP:s. Tank leaching tests (TLT) and weathering cells (WCT) were used to compare leaching behaviour in a monolithic mass contra a crushed material. Quantification of the presumed benefit of CPB was made by calculation of the cumulative leaching of As. Results from the leaching tests (TLT and WCT) showed that the inclusion of As-rich tailings into a cementitious matrix increased leaching of As. This behaviour could partially be explained by an increase of pH. The addition of alkaline binder materials to tailings increased As leaching due to the relocation of desorbed As from FEPs into less acid-tolerant species such as Ca-arsenates and cementitious As-phases. Unmodified tailings generated an acidic environment in which As-bearing FEPs were stable. The addition of binders increased the tailings' acid-neutralizing capacity and introduced more Ca-ions and Fe-precipitates into the tailings matrix, both of which may facilitate As adsorption and reduce the potential for sulphide oxidation on a long-term basis.

Computational study on hydroxybenzotriazoles as reagents for ester hydrolysis.

PubMed

Kumar, V Praveen; Ganguly, Bishwajit; Bhattacharya, Santanu

2004-12-10

1-Hydroxybenzotriazole (1) and several of its derivatives (2-5) demonstrate potent esterolytic activity toward activated esters such as p-nitrophenyl diphenyl phosphate (PNPDPP) and p-nitrophenyl hexanoate (PNPH) in cationic micelles at pH 8.2 and 25 degrees C. The deprotonated anionic forms of such reagents act as reactive species in the hydrolysis of ester. To rationalize the origin of their nucleophilic character, a detailed ab initio/DFT computational study has been performed on 1-5 along with additional hydroxybenzotriazole derivatives (6-13). The geometries of 1-hydroxybenzotriazoles (1-13) and their corresponding bases are discussed in detail. All calculations were carried out using different methods, i.e., restricted Hartree-Fock (RHF) and hybrid ab initio/DFT (B3LYP) using 6-31G and 6-31+G basis sets. Free energy of protonation ("fep") of the 1-hydroxybenzotriazoles (1-13), free energy of solvation DeltaG(aq), and the corresponding pK(a) values have been calculated. Solvation-free energies were calculated using density functional theory and the polarizable continuum model. In addition, to examine the reliability of calculated fep, benzaldehyde oxime (14) and 2-methyl propionaldehyde oxime (15) have been computed as reference systems using different methods and basis sets, the experimental feps of which are known. Our experimental finding shows that the compound 4 is the most effective catalyst for the hydrolytic cleavages of PNPDPP and PNPH. This has been predicted from our calculated fep, pK(a), and natural charge analysis results as well. In general, the introduction of electron-withdrawing substituents on 1-hydroxybenzotriazoles facilitates the lowering of pK(a) and fep. As the pK(a) values are lowered, a greater percentage of such hydroxybenzotriazoles remain in their deprotonated, anionic forms at pH 8.2. Since the anionic forms are nucleophilic, pK(a) lowering should enhance their ester cleaving capacity. However, such substitution also decreases the charge density on the catalytically active oxido atom (O(7)). Taking these two factors together, the derivatives are only modestly better nucleophiles in comparison to the parent 1-hydroxybenzotriazole. Interestingly, the introduction of electron-donating groups does not significantly enhance the charge accumulation on the oxido atom (O(7)) of 1-hydroxybenzotriazoles.

Coronary artery compression by teflon pledget granuloma following aortic valve replacement.

PubMed

Cohle, S D; Delavan, J W

1997-09-01

We describe a massive fatal posterior myocardial infarct resulting from compression of the right coronary artery by a Teflon pledget granuloma in a patient who had undergone aortic valve replacement six months before death. Other iatrogenic causes of coronary artery occlusion or compression are discussed in this paper. To our knowledge this is the first report of this surgical complication.

Plasma Igniter for Reliable Ignition of Combustion in Rocket Engines

NASA Technical Reports Server (NTRS)

Martin, Adam; Eskridge, Richard

2011-01-01

A plasma igniter has been developed for initiating combustion in liquid-propellant rocket engines. The device propels a hot, dense plasma jet, consisting of elemental fluorine and fluorine compounds, into the combustion chamber to ignite the cold propellant mixture. The igniter consists of two coaxial, cylindrical electrodes with a cylindrical bar of solid Teflon plastic in the region between them. The outer electrode is a metal (stainless steel) tube; the inner electrode is a metal pin (mild steel, stainless steel, tungsten, or thoriated-tungsten). The Teflon bar fits snugly between the two electrodes and provides electrical insulation between them. The Teflon bar may have either a flat surface, or a concave, conical surface at the open, down-stream end of the igniter (the igniter face). The igniter would be mounted on the combustion chamber of the rocket engine, either on the injector-plate at the upstream side of the engine, or on the sidewalls of the chamber. It also might sit behind a valve that would be opened just prior to ignition, and closed just after, in order to prevent the Teflon from melting due to heating from the combustion chamber.

Identification of the hydrate gel phases present in phosphate-modified calcium aluminate binders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chavda, Mehul A.; Bernal, Susan A.; Apperley, David C.

The conversion of hexagonal calcium aluminate hydrates to cubic phases in hydrated calcium aluminate cements (CAC) can involve undesirable porosity changes and loss of strength. Modification of CAC by phosphate addition avoids conversion, by altering the nature of the reaction products, yielding a stable amorphous gel instead of the usual crystalline hydrate products. Here, details of the environments of aluminium and phosphorus in this gel were elucidated using solid-state NMR and complementary techniques. Aluminium is identified in both octahedral and tetrahedral coordination states, and phosphorus is present in hydrous environments with varying, but mostly low, degrees of crosslinking. A {supmore » 31}P/{sup 27}Al rotational echo adiabatic passage double resonance (REAPDOR) experiment showed the existence of aluminium–phosphorus interactions, confirming the formation of a hydrated calcium aluminophosphate gel as a key component of the binding phase. This resolves previous disagreements in the literature regarding the nature of the disordered products forming in this system.« less

New support for high-performance liquid chromatography based on silica coated with alumina particles.

PubMed

Silveira, José Leandro R; Dib, Samia R; Faria, Anizio M

2014-01-01

A new material based on silica coated with alumina nanoparticles was proposed for use as a chromatographic support for reversed-phase high-performance liquid chromatography. Alumina nanoparticles were synthesized by a sol-gel process in reversed micelles composed of sodium bis(2-ethylhexyl)sulfosuccinate, and the support material was formed by the self-assembly of alumina layers on silica spheres. Spectroscopic and (29)Si nuclear magnetic resonance results showed evidence of chemical bonds between the alumina nanoparticles and the silica spheres, while morphological characterizations showed that the aluminized silica maintained the morphological properties of silica desired for chromatographic purposes after alumina incorporation. Stability studies indicated that bare silica showed high dissolution (~83%), while the aluminized silica remained practically unchanged (99%) after passing one liter of the alkaline mobile phase, indicating high stability under alkaline conditions. The C18 bonded aluminized silica phase showed great potential for use in high-performance liquid chromatography to separate basic molecules in the reversed-phase mode.

Rear surface light emission measurements from laser-produced shock waves in clear and Al-coated polystyrene targets

NASA Astrophysics Data System (ADS)

McLean, E. A.; Deniz, A. V.; Schmitt, A. J.; Stamper, J. A.; Obenschain, S. P.; Lehecka, T.; Mostovych, A. N.; Seely, J.

1999-08-01

The Nike KrF laser, with its very uniform focal distributions, has been used at intensities near 10 14 W/cm 2 to launch shock waves in polystyrene targets. The rear surface visible light emission differed between clear polystyrene (CH) targets and targets with a thin (125 nm) Al coating on the rear side. The uncoated CH targets showed a relatively slowly rising emission followed by a sudden fall when the shock emerges, while the Al-coated targets showed a rapid rise in emission when the shock emerges followed by a slower fall, allowing an unambiguous determination of the time the shock arrived at the rear surface. A half-aluminized target allowed us to observe this difference in a single shot. The brightness temperature of both the aluminized targets and the non-aluminized targets was slightly below but close to rear surface temperature predictions of a hydrodynamic code. A discussion of preheat effects is given.

On the kinetics of the pack - Aluminization process

NASA Technical Reports Server (NTRS)

Sivakumar, R.; Seigle, L. L.

1976-01-01

An investigation has been made of the aluminization of unalloyed Ni in fluoride-activated packs of varying Al activity. In packs of low Al activity, in which the ratio of Al to Ni was less than 50 at. pct, the specimen surface quickly came to equilibrium with the pack and remained close to equilibrium for the duration of normal coating runs. In these packs the kinetics of aluminization was controlled by diffusion in the solid. In packs of higher Al activity the surface of the specimen did not come to equilibrium with the pack and the kinetics of the process was governed by a combination of solid and gas diffusion rates. Under most conditions however, the surface composition was time-invariant and a steady-state appeared to exist at the pack-coating interface. By combining Levine and Caves' model for gaseous diffusion in pure-Al packs with calculations of solid diffusion rates some success has been achieved in explaining the results.

Aluminate effect on desilication product phase transformation

NASA Astrophysics Data System (ADS)

Peng, Hong; Vaughan, James

2018-06-01

It remains a grand challenge in the treatment of bauxite residue to physically separate zeolite (also known as the DeSilication Product, DSP) from other unleached mineral phases owing to their fine sizes, typically less than 2 μm in diameter. In this study, the effect of aluminate concentration on DSP phase transformation was investigated from synthetic NaOH-NaAl(OH)4-Na2SiO3-H2O solution at 90 °C. The results show how at relatively low aluminate concentrations of 0.125 and 0.25 M NaAl(OH)4(aq), larger zeolite crystals of up to 60 μm in diameter are formed during homogenous precipitation from aqueous solution. The precipitation process involves the conversion of zeolite LTA to sodalite via the formation of an intermediate phase, octahedral LTN. Initial amorphous solids precipitate as aggregates in which cubic zeolite LTA nucleation occurs. As the reaction proceeds, truncated octahedral LTN appears with the cubic zeolite LTA and finally sodalite crystallizes on the LTA-LTN aggregates resulting in coarsened particles.

Formation of Aluminide Coatings on Fe-Based Alloys by Chemical Vapor Deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Ying; Pint, Bruce A; Cooley, Kevin M

2008-01-01

Aluminide and Al-containing coatings were synthesized on commercial ferritic (P91) and austenitic (304L) alloys via a laboratory chemical vapor deposition (CVD) procedure for rigorous control over coating composition, purity and microstructure. The effect of the CVD aluminizing parameters such as temperature, Al activity, and post-aluminizing anneal on coating growth was investigated. Two procedures involving different Al activities were employed with and without including Cr-Al pellets in the CVD reactor to produce coatings with suitable thickness and composition for coating performance evaluation. The phase constitution of the as-synthesized coatings was assessed with the aid of a combination of X-ray diffraction, electronmore » probe microanalysis, and existing phase diagrams. The mechanisms of formation of these CVD coatings on the Fe-based alloys are discussed, and compared with nickel aluminide coatings on Ni-base superalloys. In addition, Cr-Al pellets were replaced with Fe-Al metals in some aluminizing process runs and similar coatings were achieved.« less

A New Method for Determining the Equation of State of Aluminized Explosive

NASA Astrophysics Data System (ADS)

Zhou, Zheng-Qing; Nie, Jian-Xin; Guo, Xue-Yong; Wang, Qiu-Shi; Ou, Zhuo-Cheng; Jiao, Qing-Jie

2015-01-01

The time-dependent Jones—Wilkins—Lee equation of state (JWL-EOS) is applied to describe detonation state products for aluminized explosives. To obtain the time-dependent JWL-EOS parameters, cylinder tests and underwater explosion experiments are performed. According to the result of the wall radial velocity in cylinder tests and the shock wave pressures in underwater explosion experiments, the time-dependent JWL-EOS parameters are determined by iterating these variables in AUTODYN hydrocode simulations until the experimental values are reproduced. In addition, to verify the reliability of the derived JWL-EOS parameters, the aluminized explosive experiment is conducted in concrete. The shock wave pressures in the affected concrete bodies are measured by using manganin pressure sensors, and the rod velocity is obtained by using a high-speed camera. Simultaneously, the shock wave pressure and the rod velocity are calculated by using the derived time-dependent JWL equation of state. The calculated results are in good agreement with the experimental data.

Esophagogastric fistula secondary to teflon pledget: a rare complication following laparoscopic fundoplication.

PubMed

Baladas, H G; Smith, G S; Richardson, M A; Dempsey, M B; Falk, G L

2000-01-01

Laparoscopic fundoplication has become the standard operation for gastroesophageal reflux disease. In our service, a laparoscopic fundoplication is performed as a 2-cm floppy 360 degrees wrap with division of the short gastric vessels and the fundoplication is sutured using a prolene 2/0 mattress suture (Ethicon, USA) and buttressed laterally with two teflon pledgets (PTFE 1.85 mm; low porosity, Bard, USA). We report a patient with post-operative dysphagia due to an esophagogastric fistula caused by erosion of a teflon pledget. This is the first such case in 734 laparoscopic fundoplications performed between January 1991 and December 1998. Reoperation was required, resulting in a prolonged convalescence. A review of current literature has not revealed any similar cases. Causes for this rare complication are postulated.

Randomized Trial of Infusion Set Function: Steel Versus Teflon

PubMed Central

Patel, Parul J.; Benasi, Kari; Ferrari, Gina; Evans, Mark G.; Shanmugham, Satya; Wilson, Darrell M.

2014-01-01

Abstract Background: This study compared infusion set function for up to 1 week using either a Teflon® (Dupont™, Wilmington, DE) catheter or a steel catheter for insulin pump therapy in type 1 diabetes mellitus. Subjects and Methods: Twenty subjects participating in a randomized, open-labeled, crossover study were asked to wear two Quick-Set® and two Sure-T® infusion sets (both from Medtronic Minimed, Northridge, CA) until the infusion set failed or was worn for 1 week. All subjects wore a MiniMed continuous glucose monitoring system for the duration of the study. Results: One subject withdrew from the study. There were 38 weeks of Sure-T wear and 39 weeks of Quick-Set wear with no difference in the survival curves of the infusion sets. There was, however, a 15% initial failure rate with the Teflon infusion set. After 7 days, both types of infusion sets had a 64% failure rate. Overall, 30% failed because of hyperglycemia and a failed correction dose, 13% were removed for pain, 10% were pulled out by accident, 10% had erythema and/or induration of>10 mm, 5% fell out because of loss of adhesion, and 4% were removed for infection. The main predictor of length of wear was the individual subject. There was no increase in hyperglycemia or daily insulin requirements when an infusion set was successfully used for 7 days (n=25 of 77 weeks). Conclusions: We found no difference between steel and Teflon infusion sets in their function over 7 days, although 15% of Teflon sets failed because of kinking on insertion. The strongest predictor of prolonged 7-day infusion set function was the individual subject, not the type of infusion set. PMID:24090124

Temperature and Pressure Sensors Based on Spin-Allowed Broadband Luminescence of Doped Orthorhombic Perovskite Structures

NASA Technical Reports Server (NTRS)

Eldridge, Jeffrey I. (Inventor); Chambers, Matthew D. (Inventor)

2014-01-01

Systems and methods that are capable of measuring pressure or temperature based on luminescence are discussed herein. These systems and methods are based on spin-allowed broadband luminescence of sensors with orthorhombic perovskite structures of rare earth aluminates doped with chromium or similar transition metals, such as chromium-doped gadolinium aluminate. Luminescence from these sensors can be measured to determine at least one of temperature or pressure, based on either the intense luminescence of these sensors, even at high temperatures, or low temperature techniques discussed herein.

System and process for aluminization of metal-containing substrates

DOEpatents

Chou, Yeong-Shyung; Stevenson, Jeffry W.

2017-12-12

A system and method are detailed for aluminizing surfaces of metallic substrates, parts, and components with a protective alumina layer in-situ. Aluminum (Al) foil sandwiched between the metallic components and a refractory material when heated in an oxidizing gas under a compression load at a selected temperature forms the protective alumina coating on the surface of the metallic components. The alumina coating minimizes evaporation of volatile metals from the metallic substrates, parts, and components in assembled devices that can degrade performance during operation at high temperature.

System and process for aluminization of metal-containing substrates

DOEpatents

Chou, Yeong-Shyung; Stevenson, Jeffry W

2015-11-03

A system and method are detailed for aluminizing surfaces of metallic substrates, parts, and components with a protective alumina layer in-situ. Aluminum (Al) foil sandwiched between the metallic components and a refractory material when heated in an oxidizing gas under a compression load at a selected temperature forms the protective alumina coating on the surface of the metallic components. The alumina coating minimizes evaporation of volatile metals from the metallic substrates, parts, and components in assembled devices during operation at high temperature that can degrade performance.

Possibilities and Limitations of Multioxides Crystals Growth

DTIC Science & Technology

2001-01-01

between 1 26 neodymium and lanthanum along growth direction of c,=33 mol % NdGaO3 Laj-,Nd.GaO3 single crystals 7. Concentration of 2 24- k= 0.77 (A-0.008...50, 60 and 66.6 mol.% of lanthanum aluminate concentration. The crystals adopt cubic structure at x up to 0.50 with the half of lattice constant...from the melt containing 22 mol.% and 30 Proc. SPIE Vol. 4412 more lanthanum aluminate were light yellow if the 3.90 processes were carried out in pure

Porous electrolyte retainer for molten carbonate fuel cell. [lithium aluminate

DOEpatents

Singh, R.N.; Dusek, J.T.

1979-12-27

A porous tile for retaining molten electrolyte within a fuel cell is prepared by sintering particles of lithium aluminate into a stable structure. The tile is assembled between two porous metal plates which serve as electrodes with fuels gases such as H/sub 2/ and CO opposite to oxidant gases such as O/sub 2/ and CO/sub 2/. The tile is prepared with a porosity of 55 to 65% and a pore size distribution selected to permit release of sufficient molten electrolyte to wet but not to flood the adjacent electrodes.

Phase Equilibria of Stored Chemical Energy Reactants.

DTIC Science & Technology

1984-07-25

aluminate-lithium ferrate system. Detection of a Li1 Al4/7Fe 3/704 compound: C. R. Acad. Sci., Ser. C, V. 273, No. 15, p. 888-90. McNicol, B. D. and Pott...thermodynamic properties of lithium ferrate (LiO.5Fe2 .504) and lithium aluminate (LiO 5Al 2 504) from 5 to 545 K: J. Chem. Thermodyn., V. 7, No. 7, p. 693- 2...1977, Study of low-temperature hydrothermal crystallization in lithium oxide-silicon dioxide-water, potassium oxide-silicon dioxide-water, and

Preliminary results of accelerated exposure testing of solar cell system components

NASA Technical Reports Server (NTRS)

Anagnostou, E.; Forestieri, A. F.

1977-01-01

Plastic samples and solar cell sub modules were exposed to an accelerated outdoor environment in Arizona and an accelerated simulated environment in a cyclic ultraviolet exposure tester which included humidity exposure. These tests were for preliminary screening of materials suitable for use in the manufacture of solar cell modules which are to have a 20-year lifetime. The samples were exposed for various times up to six months, equivalent to a real time exposure of four years. Suitable materials were found to be FEP-A, FEP-C, PFA, acrylic, silicone compounds and adhesives and possibly parylene. The method of packaging the sub modules was also found to be important to their performance.

Summing coincidence correction for γ-ray measurements using the HPGe detector with a low background shielding system

NASA Astrophysics Data System (ADS)

He, L.-C.; Diao, L.-J.; Sun, B.-H.; Zhu, L.-H.; Zhao, J.-W.; Wang, M.; Wang, K.

2018-02-01

A Monte Carlo method based on the GEANT4 toolkit has been developed to correct the full-energy peak (FEP) efficiencies of a high purity germanium (HPGe) detector equipped with a low background shielding system, and moreover evaluated using summing peaks in a numerical way. It is found that the FEP efficiencies of 60Co, 133Ba and 152Eu can be improved up to 18% by taking the calculated true summing coincidence factors (TSCFs) correction into account. Counts of summing coincidence γ peaks in the spectrum of 152Eu can be well reproduced using the corrected efficiency curve within an accuracy of 3%.

Effects of pressure, oxygen concentration, and forced convection on flame spread rate of Plexiglas, Nylon and Teflon

NASA Technical Reports Server (NTRS)

Notardonato, J. J.; Burkhardt, L. A.; Cochran, T. H.

1974-01-01

Experiments were conducted in which the burning of cylindrical materials in a flowing oxidant stream was studied. Plexiglas, Nylon, and Teflon fuel specimens were oriented such that the flames spread along the surface in a direction opposed to flowing gas. Correlations of flame spread rate were obtained that were power law relations in terms of pressure, oxygen concentration, and gas velocity.

Nitric Oxide Generating Polymeric Coatings for Subcutaneous Glucose Sensors

DTIC Science & Technology

2008-10-14

polymers for RSe immobilization. They both are thermoplastic poly(ether) polyurethanes but differ in composition of soft segments, hydrophobicity...thin layers of silicone rubber and Teflon AF, and the resulting device has yielded excellent NO sensitivity, high selectivity over NO2- and NH4Cl...layers over the sensor represent PDADM, 1% silicone rubber, and Teflon AF, respectively. This sensor can be coated with polymers containing RSe

Direct Push Chemical Sensors for DNAPL

DTIC Science & Technology

2007-01-01

System Improvements Problem Solution 1. Insufficient thermal protection Implemented use of microporous insulation . Lab and field tests have shown...screw thread cap with Teflon lined septum. The soil and methanol were mixed by hand and the vial was placed in an insulated cooler on ice until...Teflon lined septum. The vials were stored within an insulated cooler on ice until shipped to Columbia Analytical Services for analysis by U.S. EPA

The use of silicone based adhesives to encapsulate manganin gauges for high stress experiments

NASA Astrophysics Data System (ADS)

Be'Ery, Ilan; Rosenberg, Zvi

2007-06-01

The use of commercial manganin stress gauges has been limited to stresses in the range of 0-20 GPa due to the short-circuiting of their encapsulating materials (epoxy, Kapton) at higher pressures. Researchers at Lawrence Livermore overcome this difficulty by embedding their gauges in Teflon sheets and measured shock pressures as high as 40 GPa. The fact that Teflon can keep its resistivity at high pressures is attributed to the lack of benzene rings in its structure. On the other hand, Teflon is difficult to work with as an encapsulating material because of its poor adhesive properties. In order to overcome this difficulty we encapsulated our foils in between two tapes of Teflon which have a silicone adhesive glued to it. These are 50 μm thick commercial tapes (manufactured by 3M, type #60) which have a 50 μm thick silicone adhesive (PSA -- pressure sensitive adhesive) on them. This adhesive is easy to work with, has no benzene rings in its structure and has a lower carbon content, compared to other adhesives. Several experiments were conducted in order to directly measure the resistivity of these tapes at high pressures, as well as using them to encapsulate our manganin foils for high pressure studies.

Thin teflon-like films for MEMS: Film properties and reliability studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, B.K.; LaVigne, G.; Sniegowski, J.J.

1998-07-01

This work presents film properties and initial reliability studies for thin Teflon-like films applied to a unique test vehicle, the Sandia-designed and fabricated microengine. Results on microengines coated with the film show a factor of three improvement in their lifetime and an order of magnitude reduction in the coefficient of friction when compared to uncoated samples. Coefficients Of Friction (COF) of 0.07 for the Teflon-like film and 1.0 for uncoated samples are extracted from models which match the measured behavior of working microengines. These films, deposited form a plasma source, exhibit the ability to penetrate into very narrow, deep channelsmore » common to many MEMS devices. For as-deposited film, both the refractive index at 1.4 and the contact angle with water at 108{degree} show the film to be very similar to bulk Teflon PTFE. Film stability as a function of temperature has been examined using Fourier Transformation Infrared (FTIR) spectroscopy. The film structure as observed by the fluorine-carbon (F-C) peak is stable up to 200 C, but starts decomposing above 250 C. Film composition has been examined using X-ray photoelectron spectroscopy (XPS) and is quite different for directly exposed surfaces compared with deep, narrow channels where the deposition process is diffusion limited.« less

Selected laboratory evaluations of the whole-water sample-splitting capabilities of a prototype fourteen-liter Teflon churn splitter

USGS Publications Warehouse

Horowitz, A.J.; Smith, J.J.; Elrick, K.A.

2001-01-01

A prototype 14-L Teflon? churn splitter was evaluated for whole-water sample-splitting capabilities over a range of sediment concentratons and grain sizes as well as for potential chemical contamination from both organic and inorganic constituents. These evaluations represent a 'best-case' scenario because they were performed in the controlled environment of a laboratory, and used monomineralic silica sand slurries of known concentration made up in deionized water. Further, all splitting was performed by a single operator, and all the requisite concentration analyses were performed by a single laboratory. The prototype Teflon? churn splitter did not appear to supply significant concentrations of either organic or inorganic contaminants at current U.S. Geological Survey (USGS) National Water Quality Laboratory detection and reporting limits when test samples were prepared using current USGS protocols. As with the polyethylene equivalent of the prototype Teflon? churn, the maximum usable whole-water suspended sediment concentration for the prototype churn appears to lie between 1,000 and 10,000 milligrams per liter (mg/L). Further, the maximum grain-size limit appears to lie between 125- and 250-microns (m). Tests to determine the efficacy of the valve baffle indicate that it must be retained to facilitate representative whole-water subsampling.

Teflon pledget reinforced fundoplication causes symptomatic gastric and esophageal lumenal penetration.

PubMed

Dally, Elizabeth; Falk, Gregory L

2004-02-01

Nissen fundoplication has become the standard operative procedure for the treatment of severe gastroesophageal reflux disease. The use of Teflon pledgets in Nissen fundoplications by our unit has been associated with a number of complications that has led to a change of technique in performing these operations. We reviewed our database of all patients who had fundoplications that involved the use of pledgets and identified those who had represented with postoperative complications related to pledget erosion/migration. We identified 11 patients to date from a total of 1,175 fundoplications who had symptomatic pledget erosion occurring between 2 and 85 months after surgery (mean time 33.3 months). Symptoms included dysphagia, recurrent symptomatic gastroesophageal reflux, chest pain, and melaena, and in some cases significant morbidity was associated with the erosion. No common factor predisposing these patients to pledget erosion was identified. In the majority of cases removal of the pledget was associated with resolution of the symptoms. A review of the literature does not reveal any similar studies but problems associated with the erosion and migration of Teflon prostheses are described. The use of Teflon pledgets in fundoplication is associated with a small but significant risk of complications that has led to our unit abandoning this technique.

Erosion Results of the MISSE 7 Polymers Experiment and Zenith Polymers Experiment After 1.5 Years of Space Exposure

NASA Technical Reports Server (NTRS)

De Groh, Kim K.; Banks, Bruce A.; Yi, Grace T.; Haloua, Athena; Imka, Emily C.; Mitchell, Gianna G.; Asmar, Olivia C.; Leneghan, Halle A.; Sechkar, Edward A.

2016-01-01

Polymers and other oxidizable materials on the exterior of spacecraft in the low Earth orbit (LEO) space environment can be eroded due to reaction with atomic oxygen (AO). Therefore, in order to design durable spacecraft it is important to know the LEO AO erosion yield (E(sub y), volume loss per incident oxygen atom) of materials susceptible to AO reaction. Two spaceflight experiments, the Polymers Experiment and the Zenith Polymers Experiment, were developed to determine the AO E(sub y) of various polymers flown in ram, wake or zenith orientations in LEO. These experiments were flown as part of the Materials International Space Station Experiment 7 (MISSE 7) mission for 1.5 years on the exterior of the International Space Station (ISS). The experiments included Kapton H(TradeMark) witness samples for AO fluence determination in ram and zenith orientations. The Polymers Experiment also included samples to determine whether AO erosion of high and low ash containing polymers is dependent on fluence. This paper provides an overview of the MISSE 7 mission, a description of the flight experiments with details on the polymers flown, the characterization techniques used, the AO fluence for each exposure orientation, and the LEO E(sub y) results. The E(sub y) values ranged from 7.99x10(exp -28)cu cm/atom for TiO2/Al2O3 coated Teflon(TradeMark) fluorinated ethylene propylene (FEP) flown in the ram orientation to 1.22x10(exp -23cu cm/atom for polyvinyl alcohol (PVOH) flown in the zenith orientation. The E(sub y) of similar samples flown in different orientations has been compared to help determine solar exposure and associated heating effects on AO erosion. The E(sub y) data from these ISS spaceflight experiments provides valuable information for LEO spacecraft design purposes.

Aging of plumes from emission sources based on chamber simulation

NASA Astrophysics Data System (ADS)

Wang, X.; Deng, W.; Fang, Z.; Bernard, F.; Zhang, Y.; Yu, J.; Mellouki, A.; George, C.

2017-12-01

Study on atmospheric aging of plumes from emission sources is essential to understand their contribution to both secondary and primary pollutants occurring in the ambient air. Here we directly introduced vehicle exhaust, biomass burning plume, industrial solvents and cooking plumes into a smog chamber with 30 m3 fluorinated ethylene propylene (FEP) Teflon film reactor housed in a temperature-controlled enclosure, for characterizing primarily emitted air pollutants and for investigating secondarily formed products during photo-oxidation. Moreover, we also initiated study on the formation of secondary aerosols when gasoline vehicle exhaust is mixed with typical coal combustion pollutant SO2 or typical agricultural-related pollutant NH3. Formation of secondary organic aerosols (SOA) from typical solvent toluene was also investigated in ambient air matrix in comparison with purified air matrix. Main findings include: 1) Except for exhaust from idling gasoline vehicles, traditional precursor volatile organic compounds could only explain a very small fraction of SOA formed from vehicle exhaust, biomass burning or cooking plumes, suggesting knowledge gap in SOA precursors; 2) There is the need to re-think vehicle emission standards with a combined primary and/or secondary contribution of vehicle exhaust to PM2.5 or other secondary pollutants such as ozone; 3) When mixed with SO2, the gasoline vehicle exhaust revealed an increase of SOA production factor by 60-200% and meanwhile SO2 oxidation rates increased about a factor of 2.7; when the aged gasoline vehicle exhaust were mixing with NH3, both particle number and mass concentrations were increasing explosively. These phenomenons implied the complex interaction during aging of co-existing source emissions. 4) For typical combination of "tolune+SO2+NOx", when compared to chamber simulation with purified air as matrix, both SOA formation and SO2 oxidation were greatly enhanced under ambient air matrix, and the enhancement of SO2 oxidation was found be largely heterogonous and the enhancement of SOA formation seemed to be acid-catalyzed.

DNA adsorption onto glass surfaces

NASA Astrophysics Data System (ADS)

Carlson, Krista Lynn

Streaming potential measurements were performed on microspheres of silica, lime silicate (SLS) and calcium aluminate (CA) glasses containing silica and iron oxide (CASi and CAFe). The silicate based glasses exhibited acidic surfaces with isoelectric points (IEP) around a pH of 3 while the calcium aluminates displayed more basic surfaces with IEP ranging from 8--9.5. The surface of the calcium aluminate microspheres containing silica reacted with the background electrolyte, altering the measured zeta potential values and inhibiting electrolyte flow past the sample at ˜ pH 4 due to formation of a solid plug. DNA adsorption experiments were performed using the microspheres and a commercially available silicate based DNA isolation filter using a known quantity of DNA suspended in a chaotropic agent free 0.35 wt% Tris(hydroxymethyl)aminomethane (Tris) buffer solution. The microspheres and commercial filter were also used to isolate DNA from macrophage cells in the presence of chaotropic agents. UV absorbance at ˜260 nm and gel electrophoresis were used to quantify the amount and size of the DNA strands that adsorbed to the microsphere surfaces. In both experiments, the 43--106 microm CAFe microspheres adsorbed the largest quantity of DNA. However, the 43--106 microm SLS microspheres isolated more DNA from the cells than the <43 microm CAFe microspheres, indicating that microsphere size contributes to isolation ability. The UV absorbance of DNA at ˜260 nm was slightly altered due to the dissolution of the calcium aluminate glasses during the adsorption process. Inductively coupled plasma-optical emission spectroscopy (ICP-OES) determined that calcium and aluminum ions leached from the CA and CAFe microsphere surfaces during these experiments. Circular dichroism (CD) spectroscopy showed that the leached ions had no effect on the conformation of the DNA, and therefore would not be expected to interfere in downstream applications such as DNA replication. The 0.35 wt% Tris solution completely inhibited the formation of the hydrated crystalline layer that develops when the calcium aluminate glassess are incubated in deionized water. A Tris concentration of 0.24 wt% allowed for the formation of both hexagonal and cubic hydrates, however they were severely distorted and present in low amounts such that they were undectable by XRD.

Relatives' expressed emotion, distress and attributions in clinical high-risk and recent onset of psychosis.

PubMed

Domínguez-Martínez, Tecelli; Medina-Pradas, Cristina; Kwapil, Thomas R; Barrantes-Vidal, Neus

2017-01-01

It has been well-demonstrated that Expressed Emotion (EE) in caregivers of schizophrenia patients is related to their illness attributions, but little is known about relatives' cognitive and emotional appraisals at early stages of psychosis. This study examined differences on the relationships of EE with distress and illness attributions in 78 relatives of At-Risk Mental States (ARMS) and First-Episode of Psychosis (FEP) patients, and which of those variables better predicted EE. Criticism and Emotional Over-Involvement (EOI) were associated with distress and with several illness attributions in both groups. Anxiety was more strongly associated with criticism in ARMS than in FEP-relatives, and it was associated with EOI in the ARMS but not in the FEP-group. No differences on the relationships of EE with depression or attributions were found. Furthermore, distress and attributions of blame toward the patients predicted criticism. Attributions of control by the patient and emotional negative representation about the disorder predicted EOI. Findings highlight the need to focus on early family interventions that provide proper information and psychological support in accordance with the illness stage, to help relatives improve their understanding of the disorder, handle difficult thoughts and emotions, reduce negative appraisals, and prevent high-EE over the psychotic process. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Metacognition in first-episode psychosis and its association with positive and negative symptom profiles.

PubMed

Trauelsen, Anne Marie; Gumley, Andrew; Jansen, Jens Einar; Pedersen, Marlene Buch; Nielsen, Hanne-Grethe Lyse; Trier, Christopher Høier; Haahr, Ulrik H; Simonsen, Erik

2016-04-30

There is growing evidence that metacognitive abilities which include the ability to synthesize knowledge regarding mental states in self and others and use this ability to solve problems are impaired in non-affective psychosis and associated with positive and negative symptom severity. We sought to (a) investigate the severity of metacognitive impairments in first-episode psychosis (FEP) compared to non-clinical controls and (b) explore associations with positive and negative symptom profiles. Ninety-seven people with FEP were compared to 101 control persons. Metacognition was assessed with interviews and the Metacognitive assessment scale-abbreviated. Four groups based on positive and negative symptoms were identified by cluster analysis and compared on metacognition, childhood adversities, duration of untreated psychosis and premorbid social and academic adjustment. Those with high levels of negative symptoms had poorer metacognitive abilities. Those with high positive and low negative symptoms did not have poorer metacognitive abilities than those with low positive and negative symptoms. None of the other predictors differed between the groups. The FEP group had poorer metacognitive abilities than the control group. Inclusion of metacognition in psychosis models may improve our understanding of negative symptoms, while previous findings of a relation with positive symptoms may have been confounded. Implications for current interventions are discussed. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

The subjective experience and phenomenology of depression following first episode psychosis: a qualitative study using photo-elicitation.

PubMed

Sandhu, Amrita; Ives, Jonathan; Birchwood, Max; Upthegrove, Rachel

2013-07-01

Depression following first episode psychosis (FEP) is a frequent occurrence, with profound impact on recovery and outcome. Whilst many theories exist about the causes of depression here, research to date has been based on nosology imported wholesale from affective disorder, with little primary research on the subjective experience. This study aimed to explore the subjective experience and phenomenological features of post-psychotic depression in FEP. A qualitative methodology, photo-elicitation, together with unstructured interviews, was used to characterise aspects of depression following FEP and analysed using contemporary framework analysis. Depression was reported by participants as linked to the experience of and recovery from psychosis. The psychotic episode was a traumatic event followed by subjective doubt, shame and embarrassment. Loss and social isolation were central. Core biological symptoms did not feature. Despite the relatively small sample size, this study was able to generate in-depth data that provides useful and novel insight. Whilst generalisability is incompatible with qualitative methodology, further research using the same methodology would generate a wider range of experiences and perspectives. Understanding this dimension of psychosis in and of itself has the potential to improve and aid development of more effective and appropriately targeted interventions and associated outcomes. Crown Copyright © 2013. Published by Elsevier B.V. All rights reserved.

Robustly photogenerating H2 in water using FeP/CdS catalyst under solar irradiation

PubMed Central

Cheng, Huanqing; Lv, Xiao-Jun; Cao, Shuang; Zhao, Zong-Yan; Chen, Yong; Fu, Wen-Fu

2016-01-01

Photosplitting water for H2 production is a promising, sustainable approach for solar-to-chemical energy conversion. However, developing low-cost, high efficient and stable photocatalysts remains the major challenge. Here we report a composite photocatalyst consisting of FeP nanoparticles and CdS nanocrystals (FeP/CdS) for photogenerating H2 in aqueous lactic acid solution under visible light irradiation. Experimental results demonstrate that the photocatalyst is highly active with a H2-evolution rate of 202000 μmol h−1 g−1 for the first 5 h (106000 μmol h−1 g−1 under natural solar irradiation), which is the best H2 evolution activity, even 3-fold higher than the control in situ photo-deposited Pt/CdS system, and the corresponding to an apparent quantum efficiency of over 35% at 520 nm. More important, we found that the system exhibited excellent stability and remained effective after more than 100 h in optimal conditions under visible light irradiation. A wide-ranging analysis verified that FeP effectively separates the photoexcited charge from CdS and showed that the dual active sites in FeP enhance the activity of FeP/CdS photocatalysts. PMID:26818001

A descriptive review of qualitative studies in first episode psychosis.

PubMed

Boydell, Katherine M; Stasiulis, Elaine; Volpe, Tiziana; Gladstone, Brenda

2010-02-01

The aim of this paper is to provide a descriptive review of published qualitative research studies on first episode psychosis (FEP). A review was undertaken to describe the findings of qualitative studies in early psychosis. Keyword searches in Medline, CINAHL, ASSIA, PsychINFO databases, as well as manual searches of other relevant journals and reference lists of primary papers, were conducted. Thirty-one qualitative papers (representing 27 discrete studies) were identified. The majority reported research concerning young people based in community settings. The research studies were organized according to the following generic social processes: (i) achieving identity; (ii) acquiring perspectives; (iii) doing activity; and, (iv) experiencing relationships. The papers reviewed are based on first-person accounts obtained from individuals who have experienced FEP, their family members and service providers. This descriptive review contributes to our understanding of the complex social processes of achieving identity, acquiring perspectives, doing activities and developing relationships as experienced by young people and the significant others in their world. The cumulative findings highlight the contextually rich and detailed information made possible through qualitative studies of FEP. They begin to account for the active engagement of individuals affected by psychosis in making sense of their experience and suggest that this experience should be understood from within young people's own framework of meaning.

Plasma and serum brain-derived neurotrophic factor (BDNF) levels and their association with neurocognition in at-risk mental state, first episode psychosis and chronic schizophrenia patients.

PubMed

Heitz, Ulrike; Papmeyer, Martina; Studerus, Erich; Egloff, Laura; Ittig, Sarah; Andreou, Christina; Vogel, Tobias; Borgwardt, Stefan; Graf, Marc; Eckert, Anne; Riecher-Rössler, Anita

2018-06-25

Brain-derived neurotrophic factor (BDNF) is involved in numerous cognitive processes. Since cognitive deficits are a core feature of psychotic disorders, the investigation of BDNF levels in psychosis and their correlation with cognition has received increased attention. However, there are no studies investigating BDNF levels in individuals with an at-risk mental state (ARMS) for psychosis. Hence, the aims of the present study were: (1) assessing peripheral BDNF levels across different (potential) stages of psychosis; (2) investigating their association with cognition. Plasma and serum BDNF levels and neuropsychological performance were assessed in 16 ARMS, six first-episode psychosis (FEP), and 11 chronic schizophrenia (CS) patients. Neuropsychological assessment covered intelligence, verbal memory, working memory, attention and executive functioning. Both plasma and serum BDNF levels were highest in CS, intermediate in FEP and lowest in ARMS. Multiple regression analysis revealed a significant positive association of plasma BDNF levels with planning ability across all groups. The lower peripheral BDNF levels in ARMS compared to FEP and CS might point towards an important drop of this neurotrophin prior to the onset of frank psychosis. The associations of peripheral BDNF with planning-abilities match previous findings.

Transitions in a genetic transcriptional regulatory system under Lévy motion

PubMed Central

Zheng, Yayun; Serdukova, Larissa; Duan, Jinqiao; Kurths, Jürgen

2016-01-01

Based on a stochastic differential equation model for a single genetic regulatory system, we examine the dynamical effects of noisy fluctuations, arising in the synthesis reaction, on the evolution of the transcription factor activator in terms of its concentration. The fluctuations are modeled by Brownian motion and α-stable Lévy motion. Two deterministic quantities, the mean first exit time (MFET) and the first escape probability (FEP), are used to analyse the transitions from the low to high concentration states. A shorter MFET or higher FEP in the low concentration region facilitates such a transition. We have observed that higher noise intensities and larger jumps of the Lévy motion shortens the MFET and thus benefits transitions. The Lévy motion activates a transition from the low concentration region to the non-adjacent high concentration region, while Brownian motion can not induce this phenomenon. There are optimal proportions of Gaussian and non-Gaussian noises, which maximise the quantities MFET and FEP for each concentration, when the total sum of noise intensities are kept constant. Because a weaker stability indicates a higher transition probability, a new geometric concept is introduced to quantify the basin stability of the low concentration region, characterised by the escaping behaviour. PMID:27411445

The family empowerment program: an interdisciplinary approach to working with multi-stressed urban families.

PubMed

Cleek, Elizabeth N; Wofsy, Matt; Boyd-Franklin, Nancy; Mundy, Brian; Howell Lcsw, Tamika J

2012-06-01

The family empowerment program (FEP) is a multi-systemic family therapy program that partners multi-stressed families with an interdisciplinary resource team while remaining attached to a "traditional" mental health clinic. The rationale for this model is that far too often, families presenting at community mental health centers struggle with multiple psychosocial forces, for example problems with housing, domestic violence, child care, entitlements, racism, substance abuse, and foster care, as well as chronic medical and psychiatric illnesses, that exacerbate symptoms and impact traditional service delivery and access to effective treatment. Thus, families often experience fragmented care and are involved with multiple systems with contradictory and competing agendas. As a result, services frequently fail to harness the family's inherent strengths. The FEP partners the family with a unified team that includes representatives from Entitlements Services, Family Support and Parent Advocacy, and Clinical Staff from the agency's Outpatient Mental Health Clinic practicing from a strength-based family therapy perspective. The goal of the FEP is to support the family in achieving their goals. This is accomplished through co-construction of a service plan that addresses the family's needs in an efficient and coherent manner-emphasizing family strengths and competencies and supporting family self-sufficiency. © FPI, Inc.

The Impact of First-Episode Psychosis on the Sibling Relationship.

PubMed

Bowman, Siann; Alvarez-Jimenez, Mario; Howie, Linsey; McGorry, Patrick; Wade, Darryl

2015-01-01

Research and clinical practice in first-episode psychosis (FEP) has predominantly focused on parents and partners and has neglected siblings needs. This study aims to characterize the sibling relationship in FEP and to examine the illness-related variables that influence this relationship. Survey methodology explored the experience of 157 siblings during the first 18 months of their brother or sister's treatment. The Adult Sibling Relationship Questionnaire was used to measure the warmth, conflict, and rivalry within the relationship. A series of multivariate regression analyses were conducted to determine the relationship between illness characteristics and sibling relationship. When the young person experiencing FEP had a period of untreated psychosis longer than six months, required more than one hospital admission, had persisting psychotic symptoms, continued to use substances, and/or had a history of physical violence, warmth within the sibling relationship deteriorated. Regression analysis revealed that a history of violence was a significant predictor of the warmth, conflict, and rivalry within the sibling relationship. Suicide attempts were a significant predictor of conflict. This study has established associations between the sibling relationship and illness-related variables. This study promotes consideration of the importance of including siblings in early intervention. Given the powerful role this relationship can have as a protective factor, this study could inform future interventions involving siblings.

Can patients at risk for persistent negative symptoms be identified during their first episode of psychosis?

PubMed

Malla, Ashok K; Norman, Ross M G; Takhar, Jatinder; Manchanda, Rahul; Townsend, Laurel; Scholten, Derek; Haricharan, Raj

2004-07-01

Patients with schizophrenia who show persistent negative symptoms are an important subgroup, but they are difficult to identify early in the course of illness. The objective of this study was to examine characteristics that discriminate between first-episode psychosis (FEP) patients in whom primary negative symptoms did or did not persist after 1 year of treatment. Patients with a DSM-IV diagnosis of FEP whose primary negative symptoms did (N = 36) or did not (N = 35) persist at 1 year were contrasted on their baseline and 1-year characteristics. Results showed that patients with persistent primary negative symptoms (N = 36) had a significantly longer duration of untreated psychosis (p < .005), worse premorbid adjustment during early (p < .001) and late adolescence (p < .01), and a higher level of affective flattening (p < .01) at initial presentation compared with patients with transitory primary negative symptoms. The former group also showed significantly lower remission rates at 1 year (p < .001). Multiple regression analysis confirmed the independent contribution of duration of untreated psychosis, premorbid adjustment, and affective flattening at baseline to the patients' likelihood of developing persistent negative symptoms. It may therefore be possible to distinguish a subgroup of FEP patients whose primary negative symptoms are likely to persist on the basis of characteristics shown at initial presentation for treatment.

Individual differences in schizophrenia

PubMed Central

Lu, Wenlian; Wan, Lin; Yan, Hao; Wang, Chuanyue; Yang, Fude; Tan, Yunlong; Li, Lingjiang; Yu, Hao; Liddle, Peter F.; Palaniyappan, Lena; Zhang, Dai

2017-01-01

Background Whether there are distinct subtypes of schizophrenia is an important issue to advance understanding and treatment of schizophrenia. Aims To understand and treat individuals with schizophrenia, the aim was to advance understanding of differences between individuals, whether there are discrete subtypes, and how first-episode patients (FEP) may differ from multiple episode patients (MEP). Method These issues were analysed in 687 FEP and 1880 MEP with schizophrenia using the Positive and Negative Syndrome Scale for (PANSS) schizophrenia before and after antipsychotic medication for 6 weeks. Results The seven Negative Symptoms were correlated with each other and with P2 (conceptual disorganisation), G13 (disturbance of volition), and G7 (motor retardation). The main difference between individuals was in the cluster of seven negative symptoms, which had a continuous unimodal distribution. Medication decreased the PANSS scores for all the symptoms, which were similar in the FEP and MEP groups. Conclusions The negative symptoms are a major source of individual differences, and there are potential implications for treatment. Declaration of interests L.P. received speaker fees from Otsuka Canada and educational grant from Janssen Canada in 2017. Copyright and usage © The Royal College of Psychiatrists 2017. This is an open access article distributed under the terms of the Creative Commons Non-Commercial, No Derivatives (CC BY-NC-ND) license. PMID:29163982

Robustly photogenerating H2 in water using FeP/CdS catalyst under solar irradiation

NASA Astrophysics Data System (ADS)

Cheng, Huanqing; Lv, Xiao-Jun; Cao, Shuang; Zhao, Zong-Yan; Chen, Yong; Fu, Wen-Fu

2016-01-01

Photosplitting water for H2 production is a promising, sustainable approach for solar-to-chemical energy conversion. However, developing low-cost, high efficient and stable photocatalysts remains the major challenge. Here we report a composite photocatalyst consisting of FeP nanoparticles and CdS nanocrystals (FeP/CdS) for photogenerating H2 in aqueous lactic acid solution under visible light irradiation. Experimental results demonstrate that the photocatalyst is highly active with a H2-evolution rate of 202000 μmol h-1 g-1 for the first 5 h (106000 μmol h-1 g-1 under natural solar irradiation), which is the best H2 evolution activity, even 3-fold higher than the control in situ photo-deposited Pt/CdS system, and the corresponding to an apparent quantum efficiency of over 35% at 520 nm. More important, we found that the system exhibited excellent stability and remained effective after more than 100 h in optimal conditions under visible light irradiation. A wide-ranging analysis verified that FeP effectively separates the photoexcited charge from CdS and showed that the dual active sites in FeP enhance the activity of FeP/CdS photocatalysts.

Preparation of ceramic coating on Ti substrate by Plasma electrolytic oxidation in different electrolytes and evaluation of its corrosion resistance

NASA Astrophysics Data System (ADS)

Shokouhfar, M.; Dehghanian, C.; Baradaran, A.

2011-01-01

Ceramic oxide coatings (titania) were produced on Ti by micro-arc oxidation in different aluminate and carbonate based electrolytes. This process was conducted under constant pulsed DC voltage condition. The effect of KOH and NaF in aluminate based solution was also studied. The surface morphology, growth and phase composition of coatings were investigated using scanning electron microscope and X-ray diffraction. Corrosion behavior of the coatings was also examined by potentiodynamic polarization and electrochemical impedance spectroscopy. It was found that the sparking initiation voltage (spark voltage) had a significant effect on the form and properties of coatings. Coatings obtained from potassium aluminate based solution had a lower spark voltage, higher surface homogeneity and a better corrosion resistance than the carbonate based solution. Addition of NaF instead of KOH had improper effects on the homogeneity and adhesion of coatings which in turn caused a poor corrosion protection behavior of the oxide layer. AC impedance curves showed two time constants which is an indication of the coatings with an outer porous layer and an inner compact layer.

Hydration kinetics of CA{sub 2} and CA-Investigations performed on a synthetic calcium aluminate cement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klaus, S.R., E-mail: klaus@geol.uni-erlangen.de; Neubauer, J., E-mail: juergen.neubauer@gzn.uni-erlangen.de; Goetz-Neunhoeffer, F., E-mail: friedlinde.goetz@gzn.uni-erlangen.de

2013-01-15

Much is already known about the hydration of monocalcium aluminate (CA) in calcium aluminate cements (CACs). CA{sub 2} is known to be weakly hydraulic. Therefore, the hydration kinetics of CA{sub 2} were not of as great interest as those of the hydration of CAC. We were able to show that the hydration of CA{sub 2} begins as soon as the hydration rate of CA has reached its maximum and the first precipitation of C{sub 2}AH{sub 8} has started. The hydration of different CA/CA{sub 2} ratios was analyzed by the G-factor quantification. The individual contributions of the phases CA and CA{submore » 2} to the heat flow were calculated based on the amounts dissolved by applying thermodynamic data. The heat flow as calculated from XRD data was then compared with the measured heat flow. It obtained a good consistency between the two. The very pronounced influence of CA{sub 2} during hydration of CAC can be clearly demonstrated.« less

Using Underwater Explosion and Cylinder Expansion Tests to Calibrate Afterburn Models for Aluminized Explosives

NASA Astrophysics Data System (ADS)

Wedberg, Rasmus

2017-06-01

The study explores the combined use of underwater performance tests and cylinder expansion tests in order to parameterize detonation models for aluminized explosives which exhibit afterburning. The approach is suggested to be used in conjunction with thermochemical computation. A formulation containing RDX and aluminum powder is considered and several charges with varying masses are submerged and detonated. Pressure gauges are employed at horizontal distances scaling with the charge diameter, and the specific shock wave energy is shown to increase with charge mass. This is attributed to the combustion of aluminum particles after the Chapman-Jouguet plane. Cylinder expansion tests are carried out using Photon Doppler Velocimetry to register the wall expansion velocity. The tests are modeled using a multi-material arbitrary Lagrangian-Eulerian approach with the Guirguis-Miller model describing detonation with afterburning. The equation of state and afterburn rate law parameters are adjusted such that the model reproduces the results from the cylinder expansion and underwater tests. The approach seems promising, and might be valuable for aluminized explosive formulations intended to be used in a variety of confinement conditions. Swedish Armed Forces.

Sodium Aluminate Concentration Effects on Microstructure and Corrosion Behavior of the Plasma Electrolytic Oxidation Coatings on Pure Titanium

NASA Astrophysics Data System (ADS)

Molaei, Maryam; Fattah-Alhosseini, Arash; Gashti, Seyed Omid

2018-01-01

Sodium aluminate (NaAlO2) concentration was varied in order to understand the influence of the chemical composition of electrolyte on the spark characteristics, microstructure, and corrosion behavior of plasma electrolytic oxidation (PEO) coatings. For this purpose, PEO coatings were formed on the pure titanium substrate surface using solutions of four diverse sodium aluminate concentrations (6, 8, 10, and 12 g/L). The PEO process was carried out at constant time and voltage (180 seconds and 420 V). Studying the microstructures of samples by scanning electron microscope (SEM) and their corrosion behavior in 3.5 wt pct NaCl solutions indicated that the increase in NaAlO2 concentration (up to 10 g/L) led to an increase in uniformity and compactness, thus decreasing the size of micro-pores and increment of corrosion resistance. However, at a certain level of NaAlO2 concentration (12 g/L), large and severe sparks were created on the surface of the sample during the process, worsening the corrosion resistance and microstructure of coating.

Early transcriptomic response to Fe supply in Fe-deficient tomato plants is strongly influenced by the nature of the chelating agent.

PubMed

Zamboni, Anita; Zanin, Laura; Tomasi, Nicola; Avesani, Linda; Pinton, Roberto; Varanini, Zeno; Cesco, Stefano

2016-01-07

It is well known that in the rhizosphere soluble Fe sources available for plants are mainly represented by a mixture of complexes between the micronutrient and organic ligands such as carboxylates and phytosiderophores (PS) released by roots, as well as fractions of humified organic matter. The use by roots of these three natural Fe sources (Fe-citrate, Fe-PS and Fe complexed to water-extractable humic substances, Fe-WEHS) have been already studied at physiological level but the knowledge about the transcriptomic aspects is still lacking. The (59)Fe concentration recorded after 24 h in tissues of tomato Fe-deficient plants supplied with (59)Fe complexed to WEHS reached values about 2 times higher than those measured in response to the supply with Fe-citrate and Fe-PS. However, after 1 h no differences among the three Fe-chelates were observed considering the (59)Fe concentration and the root Fe(III) reduction activity. A large-scale transcriptional analysis of root tissue after 1 h of Fe supply showed that Fe-WEHS modulated only two transcripts leaving the transcriptome substantially identical to Fe-deficient plants. On the other hand, Fe-citrate and Fe-PS affected 728 and 408 transcripts, respectively, having 289 a similar transcriptional behaviour in response to both Fe sources. The root transcriptional response to the Fe supply depends on the nature of chelating agents (WEHS, citrate and PS). The supply of Fe-citrate and Fe-PS showed not only a fast back regulation of molecular mechanisms modulated by Fe deficiency but also specific responses due to the uptake of the chelating molecule. Plants fed with Fe-WEHS did not show relevant changes in the root transcriptome with respect to the Fe-deficient plants, indicating that roots did not sense the restored cellular Fe accumulation.

The effect of the environment on symptom dimensions in the first episode of psychosis: a multilevel study.

PubMed

Oher, F J; Demjaha, A; Jackson, D; Morgan, C; Dazzan, P; Morgan, K; Boydell, J; Doody, G A; Murray, R M; Bentall, R P; Jones, P B; Kirkbride, J B

2014-08-01

The extent to which different symptom dimensions vary according to epidemiological factors associated with categorical definitions of first-episode psychosis (FEP) is unknown. We hypothesized that positive psychotic symptoms, including paranoid delusions and depressive symptoms, would be more prominent in more urban environments. We collected clinical and epidemiological data on 469 people with FEP (ICD-10 F10-F33) in two centres of the Aetiology and Ethnicity in Schizophrenia and Other Psychoses (AESOP) study: Southeast London and Nottinghamshire. We used multilevel regression models to examine neighbourhood-level and between-centre differences in five symptom dimensions (reality distortion, negative symptoms, manic symptoms, depressive symptoms and disorganization) underpinning Schedules for Clinical Assessment in Neuropsychiatry (SCAN) Item Group Checklist (IGC) symptoms. Delusions of persecution and reference, along with other individual IGC symptoms, were inspected for area-level variation. Reality distortion [estimated effect size (EES) 0.15, 95% confidence interval (CI) 0.06-0.24] and depressive symptoms (EES 0.21, 95% CI 0.07-0.34) were elevated in people with FEP living in more urban Southeast London but disorganized symptomatology was lower (EES -0.06, 95% CI -0.10 to -0.02), after controlling for confounders. Delusions of persecution were not associated with increased neighbourhood population density [adjusted odds ratio (aOR) 1.01, 95% CI 0.83-1.23], although an effect was observed for delusions of reference (aOR 1.41, 95% CI 1.12-1.77). Hallucinatory symptoms showed consistent elevation in more densely populated neighbourhoods (aOR 1.32, 95% CI 1.09-1.61). In people experiencing FEP, elevated levels of reality distortion and depressive symptoms were observed in more urban, densely populated neighbourhoods. No clear association was observed for paranoid delusions; hallucinations were consistently associated with increased population density. These results suggest that urban environments may affect the syndromal presentation of psychotic disorders.

Are patterns of violence and aggression at presentation in patients with first-episode psychosis temporally stable? A comparison of 2 cohorts.

PubMed

Keane, Sarah; Szigeti, Attila; Fanning, Felicity; Clarke, Mary

2018-06-11

The aim of this study is to assess the prevalence and clinical correlates of aggression and violence in individuals presenting with first-episode psychosis (FEP) and to evaluate whether this prevalence has changed in recent years when compared to a similar previous study. Retrospective cross-sectional study of clinical case notes and database records using a keyword search of a sample of patients with FEP (n = 132) aged between 18 and 65 years presenting from a geographically defined catchment area to a secondary referral psychiatric service over a 4-year period (2010-2013 inclusive). Use of the Modified Overt Aggression Scale to retrospectively assess aggression and violence in the week prior to, and post, presentation with FEP. The overall proportion of individuals found to be aggressive and violent was 36% and 29%, respectively. These rates were similar to the 1995 to 1998 cohort (ie, 33% and 29%). A higher percentage of our sample (22%) was violent in the week prior to presentation compared to the 1995 to 1998 cohort (13%). Aggression was independently associated with involuntary (odds ratio [OR] = 4.085, 95% confidence interval [CI] 1.310-12.733) and inpatient treatment status (OR = 0.109, 95% CI 0.023-0.532) in the week prior to presentation and with high activation (OR = 6.770, 95% CI 1.372-33.394) and involuntary treatment status (OR = 10.163, 95% CI 2.257-45.759) in the week following presentation. Violence was associated with involuntary (OR = 3.691, 95% CI 1.197-11.382) and inpatient status (OR = 0.096, 95% CI 0.020-0.465) in the week prior to and with high activation (OR = 29.513 95% CI 1.879-463.676) the week following presentation. Aggression and violence rates in FEP appear relatively stable over time. © 2018 John Wiley & Sons Australia, Ltd.

Formation of Fe(III) oxyhydroxide colloids in freshwater and brackish seawater, with incorporation of phosphate and calcium

NASA Astrophysics Data System (ADS)

Gunnars, Anneli; Blomqvist, Sven; Johansson, Peter; Andersson, Christian

2002-03-01

The formation of Fe(III) oxyhydroxide colloids by oxidation of Fe(II) and their subsequent aggregation to larger particles were studied in laboratory experiments with natural water from a freshwater lake and a brackish coastal sea. Phosphate was incorporated in the solid phase during the course of hydrolysis of iron. The resulting precipitated amorphous Fe(III) oxyhydroxide phases were of varying composition, depending primarily on the initial dissolved Fe/P molar ratio, but with little influence by salinity or concentration of calcium ions. The lower limiting Fe/P ratio found for the solid phase suggests the formation of a basic Fe(III) phosphate compound with a stoichiometric Fe/P ratio of close to two. This implies that an Fe/P stoichiometry of ≈2 ultimately limits the capacity of precipitating Fe(III) to fix dissolved phosphate at oxic/anoxic boundaries in natural waters. In contrast to phosphorus, the uptake of calcium seemed to be controlled by sorption processes at the surface of the iron-rich particles formed. This uptake was more efficient in freshwater than in brackish water, suggesting that salinity restrains the uptake of calcium by newly formed Fe(III) oxyhydroxides in natural waters. Moreover, salinity enhanced the aggregation rate of the colloids formed. The suspensions were stabilised by the presence of organic matter, although this effect was less pronounced in seawater than in freshwater. Thus, in seawater of 6 to 33 ‰S, the removal of particles was fast (removal half time < 200 h), whereas the colloidal suspensions formed in freshwater were stable (removal half time > 900 h). Overall, oxidation of Fe(II) and removal of Fe(III) oxyhydroxide particles were much faster in seawater than in freshwater. This more rapid turnover results in lower iron availability in coastal seawater than in freshwater, making iron more likely to become a limiting element for chemical scavenging and biologic production.