Sample records for amk blending testing

  1. Antimisting kerosene: Base fuel effects, blending and quality control techniques

    NASA Technical Reports Server (NTRS)

    Yavrouian, A. H.; Ernest, J.; Sarohia, V.

    1984-01-01

    The problems associated with blending of the AMK additive with Jet A, and the base fuel effects on AMK properties are addressed. The results from the evaluation of some of the quality control techniques for AMK are presented. The principal conclusions of this investigation are: significant compositional differences for base fuel (Jet A) within the ASTM specification DI655; higher aromatic content of the base fuel was found to be beneficial for the polymer dissolution at ambient (20 C) temperature; using static mixer technology, the antimisting additive (FM-9) is in-line blended with Jet A, producing AMK which has adequate fire-protection properties 15 to 20 minutes after blending; degradability of freshly blended and equilibrated AMK indicated that maximum degradability is reached after adequate fire protection is obtained; the results of AMK degradability as measured by filter ratio, confirmed previous RAE data that power requirements to decade freshly blended AMK are significantly higher than equilibrated AMK; blending of the additive by using FM-9 concentrate in Jet A produces equilibrated AMK almost instantly; nephelometry offers a simple continuous monitoring capability and is used as a real time quality control device for AMK; and trajectory (jet thurst) and pressure drop tests are useful laboratory techniques for evaluating AMK quality.

  2. CID Aircraft pre-impact lakebed skid

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The B-720 is seen viewed moments after impact and just before hitting the wing openers. In a typical aircraft crash, fuel spilled from ruptured fuel tanks forms a fine mist that can be ignited by a number of sources at the crash site. In 1984 the NASA Dryden Flight Research Facility (after 1994 a full-fledged Center again) and the Federal Aviation Administration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID), to test crash a Boeing 720 aircraft using standard fuel with an additive designed to supress fire. The additive, FM-9, a high-molecular-weight long-chain polymer, when blended with Jet-A fuel had demonstrated the capability to inhibit ignition and flame propagation of the released fuel in simulated crash tests. This anti-misting kerosene (AMK) cannot be introduced directly into a gas turbine engine due to several possible problems such as clogging of filters. The AMK must be restored to almost Jet-A before being introduced into the engine for burning. This restoration is called 'degradation' and was accomplished on the B-720 using a device called a 'degrader.' Each of the four Pratt & Whitney JT3C-7 engines had a 'degrader' built and installed by General Electric (GE) to break down and return the AMK to near Jet-A quality. In addition to the AMK research the NASA Langley Research Center was involved in a structural loads measurement experiment, which included having instrumented dummies filling the seats in the passenger compartment. Before the final flight on December 1, 1984, more than four years of effort passed trying to set-up final impact conditions considered survivable by the FAA. During those years while 14 flights with crews were flown the following major efforts were underway: NASA Dryden developed the remote piloting techniques necessary for the B-720 to fly as a drone aircraft; General Electric installed and tested four degraders (one on each engine); and the FAA refined AMK (blending, testing, and fueling a full-size aircraft). The 15 flights had 15 takeoffs, 14 landings and a larger number of approaches to about 150 feet above the prepared crash site under remote control. These flight were used to introduce AMK one step at a time into some of the fuel tanks and engines while monitoring the performance of the engines. On the final flight (No. 15) with no crew, all fuel tanks were filled with a total of 76,000 pounds of AMK and the remotely-piloted aircraft landed on Rogers Dry Lakebed in an area prepared with posts to test the effectiveness of the AMK in a controlled impact. The CID, which some wags called the Crash in the Desert, was spectacular with a large fireball enveloping and burning the B-720 aircraft. From the standpoint of AMK the test was a major set-back, but for NASA Langley, the data collected on crashworthiness was deemed successful and just as important.

  3. Controlled Impact Demonstration instrumented test dummies installed in plane

    NASA Technical Reports Server (NTRS)

    1984-01-01

    In this photograph are seen some of dummies in the passenger cabin of the B-720 aircraft. NASA Langley Research Center instrumented a large portion of the aircraft and the dummies for loads in a crashworthiness research program. In 1984 NASA Dryden Flight Research Facility and the Federal Aviation Adimistration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID). The test involved crashing a Boeing 720 aircraft with four JT3C-7 engines burning a mixture of standard fuel with an additive called Anti-misting Kerosene (AMK) designed to supress fire. In a typical aircraft crash, fuel spilled from ruptured fuel tanks forms a fine mist that can be ignited by a number of sources at the crash site. In 1984 the NASA Dryden Flight Research Facility (after 1994 a full-fledged Center again) and the Federal Aviation Administration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID), to test crash a Boeing 720 aircraft using standard fuel with an additive designed to supress fire. The additive, FM-9, a high-molecular-weight long-chain polymer, when blended with Jet-A fuel had demonstrated the capability to inhibit ignition and flame propagation of the released fuel in simulated crash tests. This anti-misting kerosene (AMK) cannot be introduced directly into a gas turbine engine due to several possible problems such as clogging of filters. The AMK must be restored to almost Jet-A before being introduced into the engine for burning. This restoration is called 'degradation' and was accomplished on the B-720 using a device called a 'degrader.' Each of the four Pratt & Whitney JT3C-7 engines had a 'degrader' built and installed by General Electric (GE) to break down and return the AMK to near Jet-A quality. In addition to the AMK research the NASA Langley Research Center was involved in a structural loads measurement experiment, which included having instrumented dummies filling the seats in the passenger compartment. Before the final flight on December 1, 1984, more than four years of effort passed trying to set-up final impact conditions considered survivable by the FAA. During those years while 14 flights with crews were flown the following major efforts were underway: NASA Dryden developed the remote piloting techniques necessary for the B-720 to fly as a drone aircraft; General Electric installed and tested four degraders (one on each engine); and the FAA refined AMK (blending, testing, and fueling a full-size aircraft). The 15 flights had 15 takeoffs, 14 landings and a larger number of approaches to about 150 feet above the prepared crash site under remote control. These flight were used to introduce AMK one step at a time into some of the fuel tanks and engines while monitoring the performance of the engines. On the final flight (No. 15) with no crew, all fuel tanks were filled with a total of 76,000 pounds of AMK and the remotely-piloted aircraft landed on Rogers Dry Lakebed in an area prepared with posts to test the effectiveness of the AMK in a controlled impact. The CID, which some wags called the Crash in the Desert, was spectacular with a large fireball enveloping and burning the B-720 aircraft. From the standpoint of AMK the test was a major set-back, but for NASA Langley, the data collected on crashworthiness was deemed successful and just as important.

  4. CID Aircraft slap-down

    NASA Technical Reports Server (NTRS)

    1984-01-01

    In this photograph the B-720 is seen during the moments of initial impact. The left wing is digging into the lakebed while the aircraft continues sliding towards wing openers. In 1984 NASA Dryden Flight Research Facility and the Federal Aviation Administration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID). The test involved crashing a Boeing 720 aircraft with four JT3C-7 engines burning a mixture of standard fuel with an additive, Anti-misting Kerosene (AMK), designed to supress fire. In a typical aircraft crash, fuel spilled from ruptured fuel tanks forms a fine mist that can be ignited by a number of sources at the crash site. In 1984 the NASA Dryden Flight Research Facility (after 1994 a full-fledged Center again) and the Federal Aviation Administration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID), to test crash a Boeing 720 aircraft using standard fuel with an additive designed to supress fire. The additive, FM-9, a high-molecular-weight long-chain polymer, when blended with Jet-A fuel had demonstrated the capability to inhibit ignition and flame propagation of the released fuel in simulated crash tests. This anti-misting kerosene (AMK) cannot be introduced directly into a gas turbine engine due to several possible problems such as clogging of filters. The AMK must be restored to almost Jet-A before being introduced into the engine for burning. This restoration is called 'degradation' and was accomplished on the B-720 using a device called a 'degrader.' Each of the four Pratt & Whitney JT3C-7 engines had a 'degrader' built and installed by General Electric (GE) to break down and return the AMK to near Jet-A quality. In addition to the AMK research the NASA Langley Research Center was involved in a structural loads measurement experiment, which included having instrumented dummies filling the seats in the passenger compartment. Before the final flight on December 1, 1984, more than four years of effort passed trying to set-up final impact conditions considered survivable by the FAA. During those years while 14 flights with crews were flown the following major efforts were underway: NASA Dryden developed the remote piloting techniques necessary for the B-720 to fly as a drone aircraft; General Electric installed and tested four degraders (one on each engine); and the FAA refined AMK (blending, testing, and fueling a full-size aircraft). The 15 flights had 15 takeoffs, 14 landings and a larger number of approaches to about 150 feet above the prepared crash site under remote control. These flight were used to introduce AMK one step at a time into some of the fuel tanks and engines while monitoring the performance of the engines. On the final flight (No. 15) with no crew, all fuel tanks were filled with a total of 76,000 pounds of AMK and the remotely-piloted aircraft landed on Rogers Dry Lakebed in an area prepared with posts to test the effectiveness of the AMK in a controlled impact. The CID, which some wags called the Crash in the Desert, was spectacular with a large fireball enveloping and burning the B-720 aircraft. From the standpoint of AMK the test was a major set-back, but for NASA Langley, the data collected on crashworthiness was deemed successful and just as important.

  5. CID Post-impact fireball

    NASA Technical Reports Server (NTRS)

    1984-01-01

    Following its controlled impact on posts imbedded in the lakebed, the B-720 is sliding sideways and almost enveloped in the large fireball with only the aircraft's nose and right wing-tip exposed. In a typical aircraft crash, fuel spilled from ruptured fuel tanks forms a fine mist that can be ignited by a number of sources at the crash site. In 1984 the NASA Dryden Flight Research Facility (after 1994 a full-fledged Center again) and the Federal Aviation Administration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID), to test crash a Boeing 720 aircraft using standard fuel with an additive designed to supress fire. The additive, FM-9, a high-molecular-weight long-chain polymer, when blended with Jet-A fuel had demonstrated the capability to inhibit ignition and flame propagation of the released fuel in simulated crash tests. This anti-misting kerosene (AMK) cannot be introduced directly into a gas turbine engine due to several possible problems such as clogging of filters. The AMK must be restored to almost Jet-A before being introduced into the engine for burning. This restoration is called 'degradation' and was accomplished on the B-720 using a device called a 'degrader.' Each of the four Pratt & Whitney JT3C-7 engines had a 'degrader' built and installed by General Electric (GE) to break down and return the AMK to near Jet-A quality. In addition to the AMK research the NASA Langley Research Center was involved in a structural loads measurement experiment, which included having instrumented dummies filling the seats in the passenger compartment. Before the final flight on December 1, 1984, more than four years of effort passed trying to set-up final impact conditions considered survivable by the FAA. During those years while 14 flights with crews were flown the following major efforts were underway: NASA Dryden developed the remote piloting techniques necessary for the B-720 to fly as a drone aircraft; General Electric installed and tested four degraders (one on each engine); and the FAA refined AMK (blending, testing, and fueling a full-size aircraft). The 15 flights had 15 takeoffs, 14 landings and a larger number of approaches to about 150 feet above the prepared crash site under remote control. These flight were used to introduce AMK one step at a time into some of the fuel tanks and engines while monitoring the performance of the engines. On the final flight (No. 15) with no crew, all fuel tanks were filled with a total of 76,000 pounds of AMK and the remotely-piloted aircraft landed on Rogers Dry Lakebed in an area prepared with posts to test the effectiveness of the AMK in a controlled impact. The CID, which some wags called the Crash in the Desert, was spectacular with a large fireball enveloping and burning the B-720 aircraft. From the standpoint of AMK the test was a major set-back, but for NASA Langley, the data collected on crashworthiness was deemed successful and just as important.

  6. CID Aircraft post-impact lakebed skid

    NASA Technical Reports Server (NTRS)

    1984-01-01

    Moments after hitting and sliding through the wing openers the aircraft burst into flame, with a spectacular fireball seen emanating from the right inboard engine area. In a typical aircraft crash, fuel spilled from ruptured fuel tanks forms a fine mist that can be ignited by a number of sources at the crash site. In 1984 the NASA Dryden Flight Research Facility (after 1994 a full-fledged Center again) and the Federal Aviation Administration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID), to test crash a Boeing 720 aircraft using standard fuel with an additive designed to supress fire. The additive, FM-9, a high-molecular-weight long-chain polymer, when blended with Jet-A fuel had demonstrated the capability to inhibit ignition and flame propagation of the released fuel in simulated crash tests. This anti-misting kerosene (AMK) cannot be introduced directly into a gas turbine engine due to several possible problems such as clogging of filters. The AMK must be restored to almost Jet-A before being introduced into the engine for burning. This restoration is called 'degradation' and was accomplished on the B-720 using a device called a 'degrader.' Each of the four Pratt & Whitney JT3C-7 engines had a 'degrader' built and installed by General Electric (GE) to break down and return the AMK to near Jet-A quality. In addition to the AMK research the NASA Langley Research Center was involved in a structural loads measurement experiment, which included having instrumented dummies filling the seats in the passenger compartment. Before the final flight on December 1, 1984, more than four years of effort passed trying to set-up final impact conditions considered survivable by the FAA. During those years while 14 flights with crews were flown the following major efforts were underway: NASA Dryden developed the remote piloting techniques necessary for the B-720 to fly as a drone aircraft; General Electric installed and tested four degraders (one on each engine); and the FAA refined AMK (blending, testing, and fueling a full-size aircraft). The 15 flights had 15 takeoffs, 14 landings and a larger number of approaches to about 150 feet above the prepared crash site under remote control. These flight were used to introduce AMK one step at a time into some of the fuel tanks and engines while monitoring the performance of the engines. On the final flight (No. 15) with no crew, all fuel tanks were filled with a total of 76,000 pounds of AMK and the remotely-piloted aircraft landed on Rogers Dry Lakebed in an area prepared with posts to test the effectiveness of the AMK in a controlled impact. The CID, which some wags called the Crash in the Desert, was spectacular with a large fireball enveloping and burning the B-720 aircraft. From the standpoint of AMK the test was a major set-back, but for NASA Langley, the data collected on crashworthiness was deemed successful and just as important.

  7. CID Post-impact fireball

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The B-720 after impact and sliding through the wing openers is becoming enveloped in a fireball. The right wing appears to be folding over as the aircraft continues to slide. In a typical aircraft crash, fuel spilled from ruptured fuel tanks forms a fine mist that can be ignited by a number of sources at the crash site. In 1984 the NASA Dryden Flight Research Facility (after 1994 a full-fledged Center again) and the Federal Aviation Administration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID), to test crash a Boeing 720 aircraft using standard fuel with an additive designed to supress fire. The additive, FM-9, a high-molecular-weight long-chain polymer, when blended with Jet-A fuel had demonstrated the capability to inhibit ignition and flame propagation of the released fuel in simulated crash tests. This anti-misting kerosene (AMK) cannot be introduced directly into a gas turbine engine due to several possible problems such as clogging of filters. The AMK must be restored to almost Jet-A before being introduced into the engine for burning. This restoration is called 'degradation' and was accomplished on the B-720 using a device called a 'degrader.' Each of the four Pratt & Whitney JT3C-7 engines had a 'degrader' built and installed by General Electric (GE) to break down and return the AMK to near Jet-A quality. In addition to the AMK research the NASA Langley Research Center was involved in a structural loads measurement experiment, which included having instrumented dummies filling the seats in the passenger compartment. Before the final flight on December 1, 1984, more than four years of effort passed trying to set-up final impact conditions considered survivable by the FAA. During those years while 14 flights with crews were flown the following major efforts were underway: NASA Dryden developed the remote piloting techniques necessary for the B-720 to fly as a drone aircraft; General Electric installed and tested four degraders (one on each engine); and the FAA refined AMK (blending, testing, and fueling a full-size aircraft). The 15 flights had 15 takeoffs, 14 landings and a larger number of approaches to about 150 feet above the prepared crash site under remote control. These flight were used to introduce AMK one step at a time into some of the fuel tanks and engines while monitoring the performance of the engines. On the final flight (No. 15) with no crew, all fuel tanks were filled with a total of 76,000 pounds of AMK and the remotely-piloted aircraft landed on Rogers Dry Lakebed in an area prepared with posts to test the effectiveness of the AMK in a controlled impact. The CID, which some wags called the Crash in the Desert, was spectacular with a large fireball enveloping and burning the B-720 aircraft. From the standpoint of AMK the test was a major set-back, but for NASA Langley, the data collected on crashworthiness was deemed successful and just as important.

  8. CID Aircraft in practice flight above target impact site with wing cutters

    NASA Technical Reports Server (NTRS)

    1984-01-01

    In this photograph the B-720 is seen making a practice close approach over the prepared impact site. The wing openers, designed to tear open the wings and spill the fuel, are clearly seen on the ground just at the start of the bed of rocks. In a typical aircraft crash, fuel spilled from ruptured fuel tanks forms a fine mist that can be ignited by a number of sources at the crash site. In 1984 the NASA Dryden Flight Research Facility (after 1994 a full-fledged Center again) and the Federal Aviation Administration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID), to test crash a Boeing 720 aircraft using standard fuel with an additive designed to supress fire. The additive, FM-9, a high-molecular-weight long-chain polymer, when blended with Jet-A fuel had demonstrated the capability to inhibit ignition and flame propagation of the released fuel in simulated crash tests. This anti-misting kerosene (AMK) cannot be introduced directly into a gas turbine engine due to several possible problems such as clogging of filters. The AMK must be restored to almost Jet-A before being introduced into the engine for burning. This restoration is called 'degradation' and was accomplished on the B-720 using a device called a 'degrader.' Each of the four Pratt & Whitney JT3C-7 engines had a 'degrader' built and installed by General Electric (GE) to break down and return the AMK to near Jet-A quality. In addition to the AMK research the NASA Langley Research Center was involved in a structural loads measurement experiment, which included having instrumented dummies filling the seats in the passenger compartment. Before the final flight on December 1, 1984, more than four years of effort passed trying to set-up final impact conditions considered survivable by the FAA. During those years while 14 flights with crews were flown the following major efforts were underway: NASA Dryden developed the remote piloting techniques necessary for the B-720 to fly as a drone aircraft; General Electric installed and tested four degraders (one on each engine); and the FAA refined AMK (blending, testing, and fueling a full-size aircraft). The 15 flights had 15 takeoffs, 14 landings and a larger number of approaches to about 150 feet above the prepared crash site under remote control. These flight were used to introduce AMK one step at a time into some of the fuel tanks and engines while monitoring the performance of the engines. On the final flight (No. 15) with no crew, all fuel tanks were filled with a total of 76,000 pounds of AMK and the remotely-piloted aircraft landed on Rogers Dry Lakebed in an area prepared with posts to test the effectiveness of the AMK in a controlled impact. The CID, which some wags called the Crash in the Desert, was spectacular with a large fireball enveloping and burning the B-720 aircraft. From the standpoint of AMK the test was a major set-back, but for NASA Langley, the data collected on crashworthiness was deemed successful and just as important.

  9. Antimisting kerosene: Low temperature degradation and blending

    NASA Technical Reports Server (NTRS)

    Yavrouian, A.; Parikh, P.; Sarohia, V.

    1988-01-01

    The inline filtration characteristics of freshly blended and degraded antimisting fuels (AMK) at low temperature are examined. A needle valve degrader was modified to include partial recirculation of degraded fuel and heat addition in the bypass loop. A pressure drop across the needle valve of up to 4,000 psi was used. The pressure drop across a 325 mesh filter screen placed inline with the degrader and directly downstream of the needle valve was measured as a function of time for different values of pressure drop across the needle valve. A volume flux of 1 gpm/sq in was employed based on the frontal area of the screen. It was found that, at ambient temperatures, freshly blended AMK fuel could be degraded using a single pass degradation at 4,000 psi pressure drop across the needle valve to give acceptable filterability performance. At fuel temperatures below -20 C, degradation becomes increasingly difficult and a single pass technique results in unacceptable filtration performance. Recirculation of a fraction of the degraded fuel and heat addition in the bypass loop improved low temperature degradation performance. The problem is addressed of blending the AMK additive with Jet A at various base fuel temperatures.

  10. Antimisting Fuel (AMK) Flight Degrader Development and Aircraft Fuel System Investigation

    DTIC Science & Technology

    1987-02-01

    Summary of Test Results 134 CV880 Support of the CID Mission 135 Comparison of the Pump/Degrader and Needle- Valve Degrader 146 Operation on Freshly Blended...Drain Valve 53 AM 33. View of Right Side of Number 3 Engine 54 34. Redundant Shutoff Valve 55 35. Bottom View of Number 3 Engine 55 36. Onboard...Supply and Regulation/Shutoff Valves 78 44. ATMP8O-1 Pump/Degrader Test Module 79 45. Fuel Flow Circuits 80 vii La LIST OF ILLUSTRATIONS (Continued

  11. Influence of liquid water and water vapor on antimisting kerosene (AMK)

    NASA Technical Reports Server (NTRS)

    Yavrouian, A. H.; Sarolouki, M.; Sarohia, V.

    1983-01-01

    Experiments have been performed to evaluate the compatibility of liquid water and water vapor with antimisting kerosenes (AMK) containing polymer additive FM-9 developed by Imperial Chemical Industries. This effort consists of the determination of water solubility in AMK, influence of water on restoration (degradation) of AMK, and effect of water on standard AMK quality control methods. The principal conclusions of this investigation are: (1) the uptake of water in AMK critically depends upon the degree of agitation and can be as high as 1300 ppm at 20 C, (2) more than 250 to 300 ppm of water in AMK causes an insoluble second phase to form. The amount of this second phase depends on fuel temperature, agitation, degree of restoration (degradation) and the water content of the fuel, (3) laboratory scale experiments indicate precipitate formation when water vapor comes in contact with cold fuel surfaces at a much lower level of water (125 to 150 ppm), (4) precipitate formation is very pronounced in these experiments where humid air is percolated through a cold fuel (-20 C), (5) laboratory tests further indicate that water droplet settling time is markedly reduced in AMK as compared to jet A, (6) limited low temperature testing down to -30 C under laboratory conditions indicates the formation of stable, transparent gels.

  12. Antimisting kerosene JT3 engine fuel system integration study

    NASA Technical Reports Server (NTRS)

    Fiorentino, A.

    1987-01-01

    An analytical study and laboratory tests were conducted to assist NASA in determining the safety and mission suitability of the modified fuel system and flight tests for the Full-Scale Transport Controlled Impact Demonstration (CID) program. This twelve-month study reviewed and analyzed both the use of antimisting kerosene (AMK) fuel and the incorporation of a fuel degrader on the operational and performance characteristics of the engines tested. Potential deficiencies and/or failures were identified and approaches to accommodate these deficiencies were recommended to NASA Ames -Dryden Flight Research Facility. The result of flow characterization tests on degraded AMK fuel samples indicated levels of degradation satisfactory for the planned missions of the B-720 aircraft. The operability and performance with the AMK in a ground test engine and in the aircraft engines during the test flights were comparable to those with unmodified Jet A. For the final CID test, the JT-3C-7 engines performed satisfactorily while operating on AMK right up to impact.

  13. The use of AntiMisting Kerosene (AMK) in turbojet engines

    NASA Technical Reports Server (NTRS)

    Schmidt, H. W.

    1981-01-01

    The effect of antimisting kerosene (AMK) flow characteristics on fan jet engines and the impact of degradation requirements on the fuel system was evaluated. It was determined from the present program that AMK fuel cannot be used without predegradation, although some degradation occurs throughout the fuel feed system, expecially in the fuel pumps. There is a tendency toward FM-9 AMK additive agglomeration and gel formation when the liquid flows at a critical velocity through very small passages. The data indicate this phenomenon to be a function of the degree of degradation, the passage size, the differential pressure, the fluid temperature, and the accumulated flow time. Additionally, test results indicate that the long term cumulative effects of this phenomenon may require more degradation than the theoretical requirement determined from short term tests.

  14. New options of antibiotic combination therapy for multidrug-resistant Pseudomonas aeruginosa.

    PubMed

    Nakamura, I; Yamaguchi, T; Tsukimori, A; Sato, A; Fukushima, S; Matsumoto, T

    2015-01-01

    Several antibiotic combinations have demonstrated increased activity against multidrug-resistant Pseudomonas aeruginosa (MDRP) in vitro compared with a single antibiotic. The aim of this study was to investigate the activity against MDRP of some aminoglycosides in combination with monobactam, piperacillin (PIPC), and carbapenem. Clinical isolates of MDRP were collected between November 2010 and October 2012 from patients in Tokyo Medical University Hospital, Tokyo (1,015 beds). Our new method was designed to evaluate three concentrations around the breakpoint of each drug using the Checkerboard method. The aminoglycosides tested were amikacin (AMK), tobramycin (TOB), and arbekacin (ABK). Ciprofloxacin, PIPC, and biapenem (BIPM), which have been reported to demonstrate combination effects, were also tested. Sixty-six MDRP strains were identified from the 2,417 P. aeruginosa strains. Of the 66, 27 tested positive for metallo-β-lactamase (MBL). Aztreonam (AZT) with AMK or ABK was the most effective against MDRP. PIPC with AMK or ABK were somewhat effective. AZT with AMK or ABK were more effective against MBL-positive strains than MBL-negative strains. However, PIPC with AMK or ABK were more effective against MBL-negative strains than MBL-positive strains. Combination activities showed differences between MBL-positive and MBL-negative strains.

  15. Full-Scale Transport controlled Impact Demonstration

    NASA Technical Reports Server (NTRS)

    Hayduk, R. J. (Compiler)

    1986-01-01

    The controlled impact demonstration (CID) test of a transport aircraft took place on December 1, 1984, crashing at a prepared site on Rogers Dry Lakebed, Edwards Air Force Base, California. The demonstration was a setback for the antimisting kerosene (AMK) researchers. The impact conditions, considerably different from the planned scenario, exposed large quantities of degraded AMK and hydraulic fluid and caused unexpectedly hot ignition sources, bulk loss of fuel from the right wing, airflow patterns over the wings and fuselage that were untested on AMK, and fuel intrusion into the lower fuselage. The test was much more severe than planned and is generally considered to be unrepresentative of the type of survivable crash that would benefit from AMK. Ninety-seven percent of the sensors on the fuselage and wing structure, seats, dummies, restraint systems, galley, and bins were active at impact. A wealth of sensor data was collected from this once-in-a-lifetime research test. The flight data recorder experiments on board were also generally successful.

  16. The Susceptibility of Bacterial Endophthalmitis Isolates to Vancomycin, Ceftazidime, and Amikacin: a 23 Year-Review.

    PubMed

    Kodati, Shilpa; Eller, Andrew W; Kowalski, Regis P

    2017-01-01

    To investigate the in vitro susceptibility of Gram-positive and Gram-negative endophthalmitis bacterial isolates to vancomycin, amikacin, and ceftazidime over a 23-year period. Retrospective non-comparative laboratory case series. Endophthalmitis patients that were culture positive for bacteria. Laboratory records of bacteria isolated from endophthalmitis specimens collected from January 1 st 1993 to December 31 st 2015 were reviewed for incidence and standard susceptibility testing. The in vitro susceptibilities of bacteria cultured from endophthalmitis to vancomycin (VAN), amikacin (AMK), and ceftazidime (CEF). Patients with endophthalmitis were culture positive for bacteria in 665 cases.. Coagulase negative Staphylococci (CoNS) were the most common bacteria (54.6%), followed by Streptococci (Strep) species (20.8%), Staphylococcus aureus (SA) (10.2%), other Gram-positive (other-GP) bacteria (7.4%) and Gram-negative (GN) bacteria (7.1%). All Gram-positive organisms were susceptible to VAN, with the exception of 2 isolates. The in vitro susceptibilities of bacteria to AMK were: CoNS (95.3%), SA (75.0%), Strep (8.0%), GN (95.7%), and other-GP (81.1%). The in vitro susceptibilities of bacteria to CEF were: CoNS (58.5%), SA (54.4%), Strep (84.1%), GN (93.6.%), and other-GP (52.8%). There was no difference between AMK (95.7%) and CEF (93.6%) for GN coverage. AMK provided better coverage than CEF for CoNS, SA, and other-GP bacteria respectively (p<0.05, Fisher's exact), however, CEF appeared to provide better coverage (p<0.001, Fisher's exact) for Strep than AMK. Based on standard in vitro susceptibility testing, vancomycin remains an optimal antibiotic choice for the treatment of Gram-positive endophthalmitis. AMK and CEF appear to provide equal GN coverage, but AMK appears to provide better coverage for CoNS, SA, and other-GP, but not Strep.

  17. Atomization and combustion performance of antimisting kerosene and jet fuel

    NASA Technical Reports Server (NTRS)

    Fleeter, R.; Parikh, P.; Sarohia, V.

    1983-01-01

    Combustion performance of antimisting kerosene (AMK) containing FM-9 polymer was investigated at various levels of degradation (restoration of AMK for normal use in a gas turbine engine). To establish the relationship of degradation and atomization to performance in an aircraft gas turbine combustor, sprays formed by the nozzle of a JT8-D combustor with Jet A and AMK at 1 atmosphere (atm) (14.1 lb/square in absolute) pressure and 22 C at several degradation levels were analyzed. A new spray characterization technique based on digital image analysis of high resolution, wide field spray images formed under pulsed ruby laser sheet illumination was developed. Combustion tests were performed for these fuels in a JT8-D single can combustor facility to measure combustion efficiency and the lean extinction limit. Correlation of combustion performance under simulated engine operating conditions with nozzle spray Sauter mean diameter (SMD) measured at 1 atm and 22 C were observed. Fuel spray SMD and hence the combustion efficiency are strongly influenced by fuel degradation level. Use of even the most highly degraded AMK tested (filter ratio = 1.2) resulted in an increase in fuel consumption of 0.08% to 0.20% at engine cruise conditions.

  18. Aristolochia Manshuriensis Kom Inhibits Adipocyte Differentiation by Regulation of ERK1/2 and Akt Pathway

    PubMed Central

    Kwak, Dong Hoon; Lee, Ji-Hye; Kim, Taesoo; Ahn, Hyo Sun; Cho, Won-Kyung; Ha, Hyunil; Hwang, Youn-Hwan; Ma, Jin Yeul

    2012-01-01

    Aristolochia manshuriensis Kom (AMK) is a traditional medicinal herb used for the treatment of arthritis, rheumatism, hepatitis, and anti-obesity. Because of nephrotoxicity and carcinogenicity of AMK, there are no pharmacological reports on anti-obesity potential of AMK. Here, we showed AMK has an inhibitory effect on adipocyte differentiation of 3T3-L1 cells along with significantly decrease in the lipid accumulation by downregulating several adipocyte-specific transcription factors including peroxisome proliferation-activity receptor γ (PPAR-γ), CCAAT/enhancer binding protein α (C/EBP-α) and C/EBP-β, which are critical for adipogenesis in vitro. AMK also markedly activated the extracellular signal-regulated protein kinase 1/2 (ERK1/2) pathway including Ras, Raf1, and mitogen-activated protein kinase kinase 1 (MEK1), and significantly suppressed Akt pathway by inhibition of phosphoinositide-dependent kinase 1 (PDK1). Aristolochic acid (AA) and ethyl acetate (EtOAc) fraction of AMK with AA were significantly inhibited TG accumulation, and regulated two pathway (ERK1/2 and Akt) during adipocyte differentiation, and was not due to its cytotoxicity. These two pathways were upstream of PPAR-γ and C/EBPα in the adipogenesis. In addition, gene expressions of secreting factors such as fatty acid synthase (FAS), adiponectin, lipopreotein lipase (LPL), and aP2 were significantly inhibited by treatment of AMK during adipogenesis. We used the high-fat diet (HFD)-induced obesity mouse model to determine the inhibitory effects of AMK on obesity. Oral administration of AMK (62.5 mg/kg/day) significantly decreased the fat tissue weight, total cholesterol (TC), and low density lipoprotein-cholesterol (LDL-C) concentration in the blood. The results of this study suggested that AMK inhibited lipid accumulation by the down-regulation of the major transcription factors of the adipogensis pathway including PPAR-γ and C/EBP-α through regulation of Akt pathway and ERK 1/2 pathway in 3T3-L1 adipocytes and HFD-induced obesity mice, and AA may be main act in inhibitory effects of AMK during adipocyte differentiation. PMID:23166699

  19. Heat transfer, friction, and rheological characteristics of antimisting kerosene

    NASA Technical Reports Server (NTRS)

    Matthys, E.; Sarohia, V.

    1985-01-01

    Experiments were performed to determine the skin friction and heat transfer behavior of antimisting kerosene (AMK) in pipe flows. The additive used was FM-9. Based on the results of the experiments, which identify high viscosity and viscoelasticity for AMK, it is recommended that AMK be degraded. Sufficient degradation produces behavior similar to that of jet A.

  20. Design of a quasi-experiment on the effectiveness and cost-effectiveness of using the child-interview intervention during the investigation following a report of child abuse and/or neglect.

    PubMed

    Snoeren, Froukje; Hoefnagels, Cees; Lamers-Winkelman, Francien; Baeten, Paul; Evers, Silvia M A A

    2013-12-11

    In the Netherlands, suspected cases of child maltreatment can be reported to an advice and reporting center on child abuse and neglect (Advies- en Meldpunt Kindermishandeling or AMK). AMKs investigate these reports, screen for problems in the family and its surroundings and refer to child welfare. Over the last decades the focus of AMK investigations has changed from an adult-only approach to a more child-oriented approach using a Child-Interview intervention. The effects and cost-effectiveness of AMK involvement in the Netherlands have never been studied. The primary aim of this study is therefore to examine the effect of the participation of maltreated children aged 6-18 years in the Child-Interview intervention on their mental health and quality of life. As a second aim, this study will examine the balance between additional costs and effects of the Child-Interview intervention in comparison with AMK investigation without the Child-Interview intervention (adult-only intervention). A quasi-experiment will be performed consisting of two post-intervention measurements of two nonequivalent groups: an intervention group, in which the Child-Interview intervention has been used during the AMK investigation, and a control group, in which the intervention has not been used (adult-only intervention). Participants from an ongoing prospective study on the mental health and quality of life of maltreated children after a report to an AMK, will be contacted to complete a questionnaire twice. Multivariate regression analyses will be used to determine effectiveness of the Child-Interview intervention. The economic evaluation will involve a cost-effectiveness analysis and a cost-utility analysis. This will be the first study to examine the effect of AMK involvement in the Netherlands. Using the Child-Interview intervention during AMK investigation may prevent or reduce negative outcomes of child maltreatment, which may result in a lower consumption of healthcare and other services. In addition, the importance of economic evaluations is increasingly recognized, and economic evaluations about child maltreatment are scarce. Limitations include the risk of potential recall bias and selection bias. NTR3728, funded by ZonMw, project 15700.2012.

  1. Atractylodes macrocephala Koidz stimulates intestinal epithelial cell migration through a polyamine dependent mechanism.

    PubMed

    Song, Hou-Pan; Li, Ru-Liu; Zhou, Chi; Cai, Xiong; Huang, Hui-Yong

    2015-01-15

    Atractylodes macrocephala Koidz (AMK), a valuable traditional Chinese herbal medicine, has been widely used in clinical practice for treating patients with disorders of the digestive system. AMK has shown noteworthy promoting effect on improving gastrointestinal function and immunity, which might represent a promising candidate for the treatment of intestinal mucosa injury. The aim of this study was to investigate the efficacy of AMK on intestinal mucosal restitution and the underlying mechanisms via intestinal epithelial (IEC-6) cell migration model. A cell migration model of IEC-6 cells was induced by a single-edge razor blade along the diameter of the cell layers in six-well polystyrene plates. After wounding, the cells were grown in control cultures and in cultures containing spermidine (5μM, SPD, reference drug), alpha-difluoromethylornithine (2.5mM, DFMO, polyamine inhibitor), AMK (50, 100, and 200mg/L), DFMO plus SPD and DFMO plus AMK for 12h. The polyamines content was detected by high-performance liquid chromatography (HPLC) with pre-column derivatization. The Rho mRNAs expression levels were assessed by Q-RT-PCR. The Rho and non-muscle myosin II proteins expression levels were analyzed by Western blot. The formation and distribution of non-muscle myosin II stress fibers were monitored with immunostaining techniques using specific antibodies and observed by confocal microscopy. Cell migration assay was carried out using inverted microscope and the Image-Pro Plus software. All of these indexes were used to evaluate the effectiveness of AMK. (1) Treatment with AMK caused significant increases in cellular polyamines content and Rho mRNAs and proteins expression levels, as compared to control group. Furthermore, AMK exposure increased non-muscle myosin II protein expression levels and formation of non-muscle myosin II stress fibers, and resulted in an acceleration of cell migration in IEC-6 cells. (2) Depletion of cellular polyamines by DFMO resulted in a decrease of cellular polyamines levels, Rho mRNAs and proteins expression, non-muscle myosin II protein formation and distribution, thereby inhibiting IEC-6 cell migration. AMK not only reversed the inhibitory effects of DFMO on the polyamines content, Rho mRNAs and proteins expression, non-muscle myosin II protein formation and distribution, but also restored cell migration to control levels. The results obtained from this study revealed that AMK significantly stimulates the migration of IEC-6 cells through a polyamine dependent mechanism, which could accelerate the healing of intestinal injury. These findings suggest the potential value of AMK in curing intestinal diseases characterized by injury and ineffective repair of the intestinal mucosa in clinical practice. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  2. Reactions of the melatonin metabolite N(1)-acetyl-5-methoxykynuramine with carbamoyl phosphate and related compounds.

    PubMed

    Kuesel, Jana T; Hardeland, Rüdiger; Pfoertner, Henrike; Aeckerle, Nelia

    2010-01-01

    N-[2-(6-methoxyquinazolin-4-yl)-ethyl] acetamide (MQA) is a compound formed from the melatonin metabolite N(1)-acetyl-5-methoxykynuramine (AMK). We followed MQA production in reaction systems containing various putative reaction partners, in the absence and presence of hydrogen peroxide and/or copper(II). Although MQA may be formally described as a condensation product of either N(1)-acetyl-N(2)-formyl-5-methoxykynuramine (AFMK) with ammonia, or AMK with formamide, none of these combinations led to substantial quantities of MQA. However, MQA formation was observed in mixtures containing AMK, hydrogen peroxide, hydrogen carbonate and ammonia, or AMK, hydrogen peroxide, copper(II) and potentially carbamoylating agents, such as potassium cyanate or, more efficiently, carbamoyl phosphate. In the presence of hydrogen peroxide, copper(II) and carbamoyl phosphate, MQA was the major product obtained from AMK, but the omission of copper(II) mainly led to another metabolite, 3-acetamidomethyl-6-methoxycinnolinone (AMMC). This was caused by nitric oxide (NO) generated under oxidative conditions from carbamoyl phosphate, as shown by an NO spin trap. MQA formation with carbamoyl phosphate was not due to the possible decomposition product, formamide. The reaction of AMK with carbamoyl phosphate under oxidative conditions, in which inorganic phosphate and water are released and which differs from the typical process of carbamoylation via isocyanate, may be considered as a new physiological route of MQA formation.

  3. Formation of nitro musk adducts of rainbow trout hemoglobin for potential use as biomarkers of exposure.

    PubMed

    Mottaleb, M A; Zhao, X; Curtis, L R; Sovocool, G W

    2004-05-12

    The high use of nitro musk xylene (MX) and musk ketone (MK) as fragrances, and their persistence and bioaccumulation potential make them ubiquitous environmental contaminants. The 4-amino-MX (AMX) and 2-amino-MK (AMK) metabolites have been detected in trout fish hemoglobin (Hb) samples by gas chromatography-ion trap-mass spectrometry (GC-MS). Twelve Hb samples prepared from rainbow trout that were exposed to MX and MK, over a period of 24 and 72 h, were analyzed. Amino metabolites were liberated by basic hydrolysis and extracted from the fish Hb into n-hexane. The extract was concentrated, analyzed, and spiked with a standard solution (80 pg/microl) of AMX or AMK and reanalyzed. Concentrations of AMX from 10 to 25 ng/g were detected in Hb from fish taken 24 and 72 h after MX exposure. At 24 and 72 h after MK exposure, the concentration of AMK was found to be 25-51 ng/g and 9.5-25 ng/g, respectively. Concentrations of AMK in Hb from two of the three trout were substantially lower after 72 h compared with 24 h exposure. The AMX and AMK metabolites were not detected in four control samples. Average recoveries exceeding 89 and 86% could be achieved for AMX and AMK, respectively, with a coefficient of variation (CV) around 5%.

  4. RUNX1 regulates phosphoinositide 3-kinase/AKT pathway: role in chemotherapy sensitivity in acute megakaryocytic leukemia.

    PubMed

    Edwards, Holly; Xie, Chengzhi; LaFiura, Katherine M; Dombkowski, Alan A; Buck, Steven A; Boerner, Julie L; Taub, Jeffrey W; Matherly, Larry H; Ge, Yubin

    2009-09-24

    RUNX1 (AML1) encodes the core binding factor alpha subunit of a heterodimeric transcription factor complex which plays critical roles in normal hematopoiesis. Translocations or down-regulation of RUNX1 have been linked to favorable clinical outcomes in acute leukemias, suggesting that RUNX1 may also play critical roles in chemotherapy responses in acute leukemias; however, the molecular mechanisms remain unclear. The median level of RUNX1b transcripts in Down syndrome (DS) children with acute megakaryocytic leukemia (AMkL) were 4.4-fold (P < .001) lower than that in non-DS AMkL cases. Short hairpin RNA knockdown of RUNX1 in a non-DS AMkL cell line, Meg-01, resulted in significantly increased sensitivity to cytosine arabinoside, accompanied by significantly decreased expression of PIK3CD, which encodes the delta catalytic subunit of the survival kinase, phosphoinositide 3 (PI3)-kinase. Transcriptional regulation of PIK3CD by RUNX1 was further confirmed by chromatin immunoprecipitation and promoter reporter gene assays. Further, a PI3-kinase inhibitor, LY294002, and cytosine arabinoside synergized in antileukemia effects on Meg-01 and primary pediatric AMkL cells. Our results suggest that RUNX1 may play a critical role in chemotherapy response in AMkL by regulating the PI3-kinase/Akt pathway. Thus, the treatment of AMkL may be improved by integrating PI3-kinase or Akt inhibitors into the chemotherapy of this disease.

  5. FORMATION OF NITRO MUSK ADDUCTS OF RAINBOW ...

    EPA Pesticide Factsheets

    The high use of nitro musk xylene (MX) and musk ketone (MK) as fragrances, and their persistence and bioaccumulation potential make them ubiquitous environmental contaminants. The 4-amino-MX (AMX) and 2-amino-MK (AMK) metabolites have been detected in trout fish hemoglobin (Hb) samples by gas chromatography-ion trap-mass spectrometry (GC-MS). Twelve Hb samples prepared from rainbow trout that were exposed to MX and MK, over a period of 24 and 72 h, were analyzed. Amino metabolites were liberated by basic hydrolysis and extracted from the fish Hb into n-hexane. The extract was concentrated, analyzed, and spiked with a standard solution (80 pg/uL) of AMX or AMK and reanalyzed. Concentrations of AMX from 10 to 24.7 ng/g were detected in Hb from fish taken 24 and 72 h after MX exposure. At 24 and 72 h after MK exposure, the concentration of AMK was found to be 25.1 to 51, and 9.5 to 25.1 ng/g, respectively. Concentrations of AMK in Hb from two of the three trout were substantially lower after 72 h compared with 24 h exposure. The AMX and AMK metabolites were not detected in four control samples. Average recoveries exceeding 89 and 86% could be achieved for AMX and AMK, respectively, with a coefficient of variation (CV) around 5%. The research focused on in the subtasks is the development and application of state-of the-art technologies to meet the needs of the public, Office of Water, and ORD in the area of Water Quality. Located In the subtasks are the various r

  6. [Combined effect of sulbactam/cefoperazone and other antibiotics against clinical isolates of multi-resistant strains. II. In vitro combined effects of sulbactam/cefoperazone with imipenem/cilastatin, cefuzonam, flomoxef, amikacin or tobramycin].

    PubMed

    Kouda, M; Kumagai, I; Kobayashi, J; Sugai, R; Matsuzaki, H

    1991-02-01

    We evaluated combined effects of sulbactam/cefoperazone (SBT/CPZ) with each of imipenem/cilastatin (IPM), cefuzonam, flomoxef, amikacin (AMK) and tobramycin (TOB) against 324 clinical strains. Through this study, we obtained the following results. 1. Against Serratia marcescens and Enterobacter cloacae, good synergism was obtained by combining SBT/CPZ with IPM, AMK, or TOB. 2. Against Pseudomonas aeruginosa, good synergism was obtained by combining SBT/CPZ with AMK or TOB. 3. When SBT/CPZ was used in combination with IPM, antagonism was observed among about 45% of strains of P. aeruginosa.

  7. Retrieval of LAI and leaf chlorophyll content from remote sensing data by agronomy mechanism knowledge to solve the ill-posed inverse problem

    NASA Astrophysics Data System (ADS)

    Li, Zhenhai; Nie, Chenwei; Yang, Guijun; Xu, Xingang; Jin, Xiuliang; Gu, Xiaohe

    2014-10-01

    Leaf area index (LAI) and LCC, as the two most important crop growth variables, are major considerations in management decisions, agricultural planning and policy making. Estimation of canopy biophysical variables from remote sensing data was investigated using a radiative transfer model. However, the ill-posed problem is unavoidable for the unique solution of the inverse problem and the uncertainty of measurements and model assumptions. This study focused on the use of agronomy mechanism knowledge to restrict and remove the ill-posed inversion results. For this purpose, the inversion results obtained using the PROSAIL model alone (NAMK) and linked with agronomic mechanism knowledge (AMK) were compared. The results showed that AMK did not significantly improve the accuracy of LAI inversion. LAI was estimated with high accuracy, and there was no significant improvement after considering AMK. The validation results of the determination coefficient (R2) and the corresponding root mean square error (RMSE) between measured LAI and estimated LAI were 0.635 and 1.022 for NAMK, and 0.637 and 0.999 for AMK, respectively. LCC estimation was significantly improved with agronomy mechanism knowledge; the R2 and RMSE values were 0.377 and 14.495 μg cm-2 for NAMK, and 0.503 and 10.661 μg cm-2 for AMK, respectively. Results of the comparison demonstrated the need for agronomy mechanism knowledge in radiative transfer model inversion.

  8. In vitro antibacterial effect of fosfomycin combination therapy against colistin-resistant Klebsiella pneumoniae.

    PubMed

    Yu, Wei; Luo, Qixia; Shi, Qingyi; Huang, Chen; Yu, Xiao; Niu, Tianshui; Zhou, Kai; Zhang, Jiajie; Xiao, Yonghong

    2018-01-01

    Colistin is still a "last-resort" antibiotic used to manage human infections due to multidrug-resistant (MDR) Klebsiella pneumoniae . However, colistin-resistant K. pneumoniae (CR-Kp) isolates emerged a decade ago and had a worldwide distribution. The purpose of this study was to evaluate the genetic data of CR-Kp and identify the antibacterial activity of fosfomycin (FM) alone and in combination with amikacin (AMK) or colistin (COL) against CR-Kp in vitro. Three clinical CR-Kp isolates from three patients were collected. Whole-genome sequencing and bioinformatics analysis were performed. The Pharmacokinetics Auto Simulation System 400, by simulating human pharmacokinetics in vitro, was employed to simulate FM, AMK, and COL alone and in combination. Different pharmacodynamic parameters were calculated for determining the antimicrobial effect. Whole-genome sequencing revealed that none of the three isolates contain mcr gene and that no insertion was found in pmrAB , phoPQ , or mgrB genes. We found the antibacterial activity of AMK alone was more efficient than FM or COL against CR-Kp. The area between the control growth and antibacterial killing curves of FM (8 g every 8 hours) combined with AMK (15 mg/kg once daily) was higher than 170 LogCFU/mL·h -1 . In addition, the area between the control growth and antibacterial killing curves of FM (8 g every 8 hours) combined with COL (75,000 IU/kg every12 hours) was higher than that of monotherapies (>100 LogCFU/mL·h -1 vs <80 LogCFU/mL·h -1 ). FM (8 g every 8 hours) combined with AMK (15 mg/kg once daily) was effective at maximizing bacterial killing against CR-Kp.

  9. [The combination effects of antibacterial agents against clinical isolated multiple-drug resistant Pseudomonas aeruginosa].

    PubMed

    Maesaki, Shigefumi; Yamaguchi, Toshiyuki; Sasaki, Kazumasa; Hashikita, Giichi; Shibuya, Shunsuke; Watanabe, Masaharu; Takayama, Sadao; Kawakami, Sayoko; Nagasawa, Mitsuaki; Suzuki, Noriyasu; Uchida, Takashi; Okabe, Tadashi; Kobayashi, Sugako

    2006-02-01

    The effectiveness of antibacterial agents against 70 strains of clinically isolated multiple-drug resistant Pseudomonas aeruginosa (MDRP) was measured by the micro dilution method. Fifty of all strains (71%) produced metallo-beta-lactamase and the IMP-1 gene was detected by polymerase chain reaction (PCR). The MIC90 (the minimum inhibitory concentration of an antibiotic necessary to inhibit the growth of 90% of bacterial strains) values of biapenem (BIPM), meropenem (MEPM), tazobactam/piperacillin (TAZ/PIPC), sulbactam/ cefoperazone (SBT/CPZ), cefepime (CFPM), ciprofloxacin (CPFX), pazufloxacin (PZFX), amikacin (AMK) and aztreonam (AZT) were found to be 265, 512, 256, 512, 512, 64, 128, 128 and 128 microg/mL, respectively. The in vitro combination effects of antibacterial agents were examined against 62 strains of MDRP and the synergy or additive effects were evaluated by fractional inhibitory concentration (FIC) index calculated by the checkerboard method. The combination of AMK and AZT showed synergy effects on 15/59 (25.4%) strains of MDRP. The synergy and additive effects on the MDRP strains were also found by the other antibacterial agents combination such as TAZ/PIPC and AMK, CFPM and AMK, and SBT/CPZ and AZT. These results suggested the necessity of further investigation of clinical usefulness.

  10. In vitro synergism of magnolol and honokiol in combination with antibacterial agents against clinical isolates of methicillin-resistant Staphylococcus aureus (MRSA).

    PubMed

    Zuo, Guo-Ying; Zhang, Xin-Juan; Han, Jun; Li, Yu-Qing; Wang, Gen-Chun

    2015-12-01

    Methicillin-resistant Staphylococcus aureus (MRSA) is a problematic pathogen posing a serious therapeutic challenge in the clinic. It is often multidrug-resistant (MDR) to conventional classes of antibacterial agents and there is an urgent need to develop new agents or strategies for treatment. Magnolol (ML) and honokiol (HL) are two naturally occurring diallylbiphenols which have been reported to show inhibition of MRSA. In this study their synergistic effects with antibacterial agents were further evaluated via checkerboard and time-kill assays. The susceptibility spectrum of clinical MRSA strains was tested by the disk diffusion method. The minimal inhibitory concentrations (MICs) and minimal bactericidal concentrations (MBCs) of ML and HL were assayed by broth microdilution. The synergy was evaluated through checkerboard microdilution and time-killing experiments. ML and HL showed similar activity against both MSSA and MRSA with MIC/MBC at 16 ~ 64 mg/L, with potency similar to amikacin (AMK) and gentamicin (GEN). When they were used in combination with conventional antibacterial agents, they showed bacteriostatic synergy with FICIs between 0.25 ~ 0.5, leading to the combined MICs decreasing to as low as 1 ~ 2 and 1 ~ 16 mg/L for ML (HL) and the agents, respectively. MIC50 of the combinations decreased from 16 mg/L to 1 ~ 4 mg/L for ML (HL) and 8 ~ 128 mg/L to 2 ~ 64 mg/L for the antibacterial agents, which exhibited a broad spectrum of synergistic action with aminoglycosides (AMK, etilmicin (ETM) and GEN), floroquinolones (levofloxacin (LEV), ciprofloxacin and norfloxacin), fosfomycin (FOS) and piperacillin. The times of dilution (TOD, the extent of decreasing in MIC value) were determined up to 16 for the combined MIC. A more significant synergy after combining was determined as ML (HL) with AMK, ETM, GEN and FOS. ML (HL) combined with antibacterial agents did not show antagonistic effects on any of the ten MRSA strains. Reversal effects of MRSA resistance to AMK and GEN by ML and HL were also observed, respectively. All the combinations also showed better dynamic bactericidal activity against MRSA than any of single ML (HL) or the agents at 24 h incubation. The more significant synergy of combinations were determined as HL (ML) + ETM, HL + LEV and HL + AMK (GEN or FOS), with △LC24 of 2.02 ~ 2.25. ML and HL showed synergistic potentiation of antibacterial agents against clinical isolates of MRSA and warrant further pharmacological investigation.

  11. Degradation and Characterization of Antimisting Kerosene (AMK).

    DTIC Science & Technology

    1982-12-01

    EXECUTIVE SUMMARY ................................................... I. INTRODUCTION ............................................... 2 II. DEGRADER...P - density Pll-P22 - normal stress difference P12 - shear stress x EXECUTIVE SI-9ARY CSingle pass degradation of Antinmisting Kerosene (ANIK) has...While the jet thrust experiment is more difficult to execute and interpret than flow experiments, a quality control test based on normal stresses would

  12. Application of electrolysis to inactivation of antibacterials in clinical use.

    PubMed

    Nakano, Takashi; Hirose, Jun; Kobayashi, Toyohide; Hiro, Naoki; Kondo, Fumitake; Tamai, Hiroshi; Tanaka, Kazuhiko; Sano, Kouichi

    2013-04-01

    Contamination of surface water by antibacterial pharmaceuticals (antibacterials) from clinical settings may affect aquatic organisms, plants growth, and environmental floral bacteria. One of the methods to decrease the contamination is inactivation of antibacterials before being discharged to the sewage system. Recently, we reported the novel method based on electrolysis for detoxifying wastewater containing antineoplastics. In the present study, to clarify whether the electrolysis method is applicable to the inactivation of antibacterials, we electrolyzed solutions of 10 groups of individual antibacterials including amikacin sulfate (AMK) and a mixture (MIX) of some commercial antibacterials commonly prescribed at hospitals, and measured their antibacterial activities. AMK was inactivated in its antibacterial activities and its concentration decreased by electrolysis in a time-dependent manner. Eighty to ninety-nine percent of almost all antibacterials and MIX were inactivated within 6h of electrolysis. Additionally, cytotoxicity was not detected in any of the electrolyzed solutions of antibacterials and MIX by the Molt-4-based cytotoxicity test. Copyright © 2012 Elsevier Inc. All rights reserved.

  13. Second-line drug susceptibility breakpoints for Mycobacterium tuberculosis using the MODS assay.

    PubMed

    Trollip, A P; Moore, D; Coronel, J; Caviedes, L; Klages, S; Victor, T; Romancenco, E; Crudu, V; Ajbani, K; Vineet, V P; Rodrigues, C; Jackson, R L; Eisenach, K; Garfein, R S; Rodwell, T C; Desmond, E; Groessl, E J; Ganiats, T G; Catanzaro, A

    2014-02-01

    To establish breakpoint concentrations for the fluoroquinolones (moxifloxacin [MFX] and ofloxacin [OFX]) and injectable second-line drugs (amikacin [AMK], kanamycin [KM] and capreomycin [CPM]) using the microscopic observation drug susceptibility (MODS) assay. A multinational study conducted between February 2011 and August 2012 in Peru, India, Moldova and South Africa. In the first phase, breakpoints for the fluoroquinolones and injectable second-line drugs (n = 58) were determined. In the second phase, MODS second-line drug susceptibility testing (DST) as an indirect test was compared to MGIT™ DST (n = 89). In the third (n = 30) and fourth (n = 156) phases, we determined the reproducibility and concordance of MODS second-line DST directly from sputum. Breakpoints for MFX (0.5 μg/ml), OFX (1 μg/ml), AMK (2 μg/ml), KM (5 μg/ml) and CPM (2.5 μg/ml) were determined. In all phases, MODS results were highly concordant with MGIT DST. The few discrepancies suggest that the MODS breakpoint concentrations for some drugs may be too low. MODS second-line DST yielded comparable results to MGIT second-line DST, and is thus a promising alternative. Further studies are needed to confirm the accuracy of the drug breakpoints and the reliability of MODS second-line DST as a direct test.

  14. High-Molecular Compounds (Selected Articles).

    DTIC Science & Technology

    1987-09-11

    with methacrylamide (AMK), methacrylic acid (MAK) and ethylene-glycolmethacrylate (MEG), copolymer of methylmethacrylate (MMA) and MAK and...polymerization in medium of isopropyl or butyl alcohol with dinitrile of azoisobutyric acid (DAK). Samples for the tests re-precipitated from acetone... temperatu .-es T. T in films of PVTs process of thermal structuring occurs, as a result of which polymer changes into undissolved state. * REFERENCES

  15. Cluster-distinguishing genotypic and phenotypic diversity of carbapenem-resistant Gram-negative bacteria in solid-organ transplantation patients: a comparative study.

    PubMed

    Karampatakis, Theodoros; Geladari, Anastasia; Politi, Lida; Antachopoulos, Charalampos; Iosifidis, Elias; Tsiatsiou, Olga; Karyoti, Aggeliki; Papanikolaou, Vasileios; Tsakris, Athanassios; Roilides, Emmanuel

    2017-07-31

    Solid-organ transplant recipients may display high rates of colonization and/or infection by multidrug-resistant bacteria. We analysed and compared the phenotypic and genotypic diversity of carbapenem-resistant (CR) strains of Klebsiella pneumoniae, Pseudomonas aeruginosa and Acinetobacter baumannii isolated from patients in the Solid Organ Transplantation department of our hospital. Between March 2012 and August 2013, 56 CR strains from various biological fluids underwent antimicrobial susceptibility testing with VITEK 2, molecular analysis by PCR amplification and genotypic analysis with pulsed-field gel electrophoresis (PFGE). They were clustered according to antimicrobial drug susceptibility and genotypic profiles. Diversity analyses were performed by calculating Simpson's diversity index and applying computed rarefaction curves.Results/Key findings. Among K. pneumoniae, KP-producers predominated (57.1 %). VIM and OXA-23 carbapenemases prevailed among P. aeruginosa and A. baumannii (89.4 and 88.9 %, respectively). KPC-producing K. pneumoniae and OXA-23 A. baumannii were assigned in single PFGE pulsotypes. VIM-producing P. aeruginosa generated multiple pulsotypes. CR K. pneumoniae strains displayed phenotypic diversity in tigecycline, colistin (CS), amikacin (AMK), gentamicin (GEN) and co-trimoxazole (SXT) (16 clusters); P. aeruginosa displayed phenotypic diversity in cefepime (FEP), ceftazidime, aztreonam, piperacillin, piperacillin-tazobactam, AMK, GEN and CS (9 clusters); and A. baumannii displayed phenotypic diversity in AMK, GEN, SXT, FEP, tobramycin and rifampicin (8 clusters). The Simpson diversity indices for the interpretative phenotype and PFGE analysis were 0.89 and 0.6, respectively, for K. pneumoniae strains (P<0.001); 0.77 and 0.6 for P. aeruginosa (P=0.22); and 0.86 and 0.19 for A. baumannii (P=0.004). The presence of different antimicrobial susceptibility profiles does not preclude the possibility that two CR K. pneumoniae or A. baumannii isolates are clonally related.

  16. Degradation and Characterization of Antimisting Kerosene (AMK).

    DTIC Science & Technology

    1981-06-01

    the pass/fail criterion in the JPL test, which is taken as a flame length of I meter, appeared to be different from the critical velocity in the...SPILLAG;E TEST 9 passed at velocities up to 80 m/s, the flame length in all these cases appeared to be about 1/2 to 3/4 meter and did not increase...significantly with air velocity from 50-80 m/s. More importantly, the flame length for the sample without amine, which was rated as a fail at 50 m/s (i.e., had

  17. 20th Annual Systems Engineering Conference. Volume 3, Thursday

    DTIC Science & Technology

    2017-10-26

    Assurance Center (JFAC) 2017 Update u Mr. Thomas Hurt, Department of Defense 4B1 Tr a c k 2 m il le r Education & Training 19813 Shaping the...k s a n d r a M a r k i n a - K h u s i d amk@mitre.org D r. R ya n J a c o b s r j a c o b s @mitre.org October 2017 NDIA 20th Annual Systems...A n t u l lantul@mitre.org D r. A l e k s a n d r a M a r k i n a - K h u s i d amk@mitre.org D r. R y a n J a c o b s rjacobs@mitre.org J a

  18. Potentiation activity of multiple antibacterial agents by Salvianolate from the Chinese medicine Danshen against methicillin-resistant Staphylococcus aureus (MRSA).

    PubMed

    Liu, Qing-Qing; Han, Jun; Zuo, Guo-Ying; Wang, Gen-Chun; Tang, Hua-Shu

    2016-05-01

    Salvianolate (SAL) is a prescribed medicine from the Chinese herb Danshen (Salvia miltiorrhiza Bunge). It has been widely used in treatment of coronary and other diseases with significant effects. The in vitro antimicrobial activities of SAL against infectious pathogens were assayed and its combined effects on 10 clinical isolates of SCCmec III type methicillin-resistant Staphylococcus aureus (MRSA) with ten antibiotics were evaluated. Susceptibility to each agent alone was tested using a broth microdilution method, and the chequerboard and time-kill experiments were used for the combined activities. The results showed MIC was 128-256 mg/L for SAL used alone against MRSA. Significant synergies were observed for SAL/Ampicillin (Fosfomycin, Erythromycin, Piperacillin-tazobactam or Clindamycin) combination against over half of the isolates, with their MICs reduced by times of dilution (TOD) to 4-32 (FICIs 0.375-0.5), respectively. SAL/AMP combination showed the best combined effect of synergy on bacteriostatic and bactericidal activities, while SAL/AMK combination reversed the resistance of MRSA to AMK. The results demonstrated that SAL enhanced widely the in vitro anti-MRSA efficacy of the ten antibacterial agents, which had potential for combinatory therapy of patients infected with MRSA and warrants further investigations. Copyright © 2015 The Authors. Production and hosting by Elsevier B.V. All rights reserved.

  19. An assessment of the use of antimisting fuel in turbofan engines

    NASA Technical Reports Server (NTRS)

    Fiorentino, A. J.; Planell, J. R.

    1983-01-01

    An evaluation was made on the effects of using antimisting kerosene (AMK) on the performance of the components from the fuel system and the combustor of current in service JT8D aircraft engines. The objectives were to identify if there were any problems associated with using antimisting kerosene and to determine the extent of shearing or degradation required to allow the engine components to achieve satisfactory operation. The program consisted of a literature survey and a test program which evaluated the antimisting kerosene fuel in laboratory and bench component testing, and assessed the performance of the combustor in a high pressure facility and in an altitude relight/cold ignition facility.

  20. [Characterization and determination of antibiotic resistance profiles of a single clone Acinetobacter baumannii strains isolated from blood cultures].

    PubMed

    Karagöz, Alper; Baran, Irmak; Aksu, Neriman; Acar, Sümeyra; Durmaz, Rıza

    2014-10-01

    Acinetobacter baumannii which is a significant cause of nosocomial infections, increases the rate of morbidity and mortality in health care settings especially in intensive care units (ICUs). The aim of this study was to determine the antibiotic resistance profiles of A.baumannii strains isolated from blood cultures of inpatients from different ICUs, wards and hospital environment and evaluate their clonal relationships and epidemiologic features. A total of 54 A.baumannii strains (47 from the blood cultures and 7 from the hospital environment), identified between 01 January 2012-28 December 2012 at the Clinical Microbiology Laboratory of Ankara Numune Training and Research Hospital, Turkey, were included in the study. Identification of A.baumannii isolates and their antimicrobial [sulbactam-ampicillin (SAM), piperacillin (PIP), piperacillin-tazobactam (TZP), ceftazidime (CFZ), cefoperazone-sulbactam (SCF), cefepime (CEF), imipenem (IMP), meropenem (MER), amikacin (AMK), gentamicin (GEN), netilmicin (NT), ciprofloxacin (CIP), levofloxacin (LVF), tetracycline (TET), tigecycline (TG), colistin (COL), trimethoprim-sulfamethoxazole (SXT)] susceptibility testing were performed by Vitek 2 (bioMérieux, France) system. The clonal relationship between the A.baumannii isolates was analysed by pulsed-field gel electrophoresis (PFGE). In our study colistin, tigecycline and netilmicin were found to be the most effective agents against A.baumannii isolates. All of the clinical isolates (n= 47) were found susceptible to COL, however all were resistant to SAM, PIP, TZP, CEF, IPM, CFZ, MER and CIP. While 1.85%, 14.8%, 14.8%, 16.6%, 59.2% and 22.2% of the isolates were susceptible to SCF, AMK, NT, GEN, TG and SXT, respectively; 1.85%, 1.85%, 9.2%, 16.6%, 38.8% and 27.7% of the isolates were intermediate to SCF, TET, AMK, NT, LVF and TG, respectively. Similarly, all of the environmental A.baumannii isolates (n= 7) were resistant to SAM, PIP, TZP, CFZ, CEF, IPM, MER and CIP, and all were susceptible to TG and COL. The resistance rates of the environmental isolates to SCF, AMK, GEN, NT, LVF, TET and SXT were determined as 57.1%, 85.7%, 85.7%, 28.8%, 28.6%, 85.7% and 57.1%, respectively. PFGE analysis done by the use of ApaI enzyme revealed the presence of one major clone. Dendogram analysis indicated that environmental and clinical isolates were in the same clone indicating that the outbreak was possibly originated from the same internal ICUs. Our data emphasized that multidrug resistant A.baumannii isolates were quite common in our hospital, and enviromental cross-contamination throughout the year was confirmed by molecular methods. Despite the precautions such as continous education on effective hand washing, use of gloves and hospital cleaning, established in our hospital, this single clonal spread was attributed to staff shortage and poor adherence to infection control rules. In conclusion, for the prevention of dissemination of multidrug resistant A.baumannii strains and control of nosocomial infections, infection control strategies should be established and strict compliance to these rules should be provided.

  1. Genotypic and phenotypic characteristics of aminoglycoside-resistant Mycobacterium tuberculosis isolates in Latvia.

    PubMed

    Bauskenieks, Matiss; Pole, Ilva; Skenders, Girts; Jansone, Inta; Broka, Lonija; Nodieva, Anda; Ozere, Iveta; Kalvisa, Adrija; Ranka, Renate; Baumanis, Viesturs

    2015-03-01

    Mutations causing resistance to aminoglycosides, such as kanamycin (KAN), amikacin (AMK), and streptomycin, are not completely understood. In this study, polymorphisms of aminoglycoside resistance influencing genes such as rrs, eis, rpsL, and gidB in 41 drug-resistant and 17 pan-sensitive Mycobacterium tuberculosis clinical isolates in Latvia were analyzed. Mutation A1400G in rrs gene was detected in 92% isolates with high resistance level to KAN and diverse MIC level to AMK. Mutations in promoter region of eis were detected in 80% isolates with low-level MIC of KAN. The association of K43R mutation in rpsL gene, a mutation in the rrs gene at position 513, and various polymorphisms in gidB gene with distinct genetic lineages of M. tuberculosis was observed. The results of this study suggest that association of different controversial mutations of M. tuberculosis genes to the drug resistance phenotype should be done in respect to genetic lineages. Copyright © 2015 Elsevier Inc. All rights reserved.

  2. Update of incidence and antimicrobial susceptibility trends of Escherichia coli and Klebsiella pneumoniae isolates from Chinese intra-abdominal infection patients.

    PubMed

    Zhang, Hui; Yang, Qiwen; Liao, Kang; Ni, Yuxing; Yu, Yunsong; Hu, Bijie; Sun, Ziyong; Huang, Wenxiang; Wang, Yong; Wu, Anhua; Feng, Xianju; Luo, Yanping; Chu, Yunzhuo; Chen, Shulan; Cao, Bin; Su, Jianrong; Duan, Qiong; Zhang, Shufang; Shao, Haifeng; Kong, Haishen; Gui, Bingdong; Hu, Zhidong; Badal, Robert; Xu, Yingchun

    2017-12-18

    To evaluate in vitro susceptibilities of aerobic and facultative Gram-negative bacterial (GNB) isolates from intra-abdominal infections (IAIs) to 12 selected antimicrobials in Chinese hospitals from 2012 to 2014. Hospital acquired (HA) and community acquired (CA) IAIs were collected from 21 centers in 16 Chinese cities. Extended spectrum beta-lactamase (ESBL) status and antimicrobial susceptibilities were determined at a central laboratory using CLSI broth microdilution and interpretive standards. From all isolated strains the Enterobacteriaceae (81.1%) Escherichia coli accounted for 45.4% and Klebsiella pneumoniae for 20.1%, followed by Enterobacter cloacae (5.2%), Proteus mirabilis (2.1%), Citrobacter freundii (1.8%), Enterobacter aerogenes (1.8%), Klebsiella oxytoca (1.4%), Morganella morganii (1.2%), Serratia marcescens (0.7%), Citrobacter koseri (0.3%), Proteus vulgaris (0.3%) and others (1.0%). Non- Enterobacteriaceae (18.9%) included Pseudomonas aeruginosa (9.8%), Acinetobacter baumannii (6.7%), Stenotrophomonas maltophilia (0.9%), Aeromonas hydrophila (0.4%) and others (1.1%). ESBL-screen positive Escherichia coli isolates (ESBL+) showed a decreasing trend from 67.5% in 2012 to 58.9% in 2014 of all Escherichia coli isolates and the percentage of ESBL+ Klebsiella pneumoniae isolates also decreased from 2012 through 2014 (40.4% to 26.6%), which was due to reduced percentages of ESBL+ isolates in HA IAIs for both bacteria. The overall susceptibilities of all 5160 IAI isolates were 87.53% to amikacin (AMK), 78.12% to piperacillin-tazobactam (TZP) 81.41% to imipenem (IMP) and 73.12% to ertapenem (ETP). The susceptibility of ESBL-screen positive Escherichia coli strains was 96.77%-98.8% to IPM, 91.26%-93.16% to ETP, 89.48%-92.75% to AMK and 84.86%-89.34% to TZP, while ESBL-screen positive Klebsiella pneumoniae strains were 70.56%-80.15% susceptible to ETP, 80.0%-87.5% to IPM, 83.82%-87.06% to AMK and 63.53%-68.38% to TZP within the three year study. Susceptibilities to all cephalosporins and fluoroquinolones were less than 50% beside 66.5% and 56.07% to cefoxitin (FOX) for ESBL+ Escherichia coli and Klebsiella pneumoniae strains respectively. The total ESBL+ rates decreased in Escherichia coli and Klebsiella pneumoniae IAI isolates due to fewer prevalence in HA infections. IPM, ETP and AMK were the most effective antimicrobials against ESBL+ Escherichia coli and Klebsiella pneumoniae IAI isolates in 2012-2014 and a change of fluoroquinolone regimens for Chinese IAIs is recommended.

  3. Financial Autonomy and Challenges to Being a Regionally Responsive Higher Education Institution

    ERIC Educational Resources Information Center

    Kohtamaki, Vuokko; Lyytinen, Anu

    2004-01-01

    This paper discusses some current problems and challenges of the Finnish AMKs (polytechnic institutions), and whether financial autonomy could contribute to finding solutions for some of these problems. It provides an overview of the current status of financial autonomy of polytechnics in 6 European countries, and finally attempts to find links…

  4. FORMATION OF NITRO MUSK ADDUCTS OF RAINBOW TROUT HEMOGLOBIN FOR POTENTIAL USE AS BIOMARKERS OF EXPOSURE

    EPA Science Inventory

    The high use of nitro musk xylene (MX) and musk ketone (MK) as fragrances, and their persistence and bioaccumulation potential make them ubiquitous environmental contaminants. The 4-amino-MX (AMX) and 2-amino-MK (AMK) metabolites have been detected in trout fish hemoglobin (Hb) s...

  5. Update of contemporary antimicrobial resistance rates across China: reference testing results for 12 medical centers (2011).

    PubMed

    Jones, Ronald N; Castanheira, Mariana; Hu, Bijie; Ni, Yuxing; Lin, Stephen S F; Mendes, Rodrigo E; Wang, Yao

    2013-11-01

    Antimicrobial resistance (R) surveillance across Asia and especially in China has documented unique patterns and mechanisms. This 2011 study reports results for 2278 isolates from 12 hospitals in China (94-216 strains/site); most from bacteremia (20.4%), pneumonias (29.1%), or skin and skin structure infections (20.9%). Samples were tested by reference broth microdilution methods, interpreted by published susceptibility (S) breakpoints. The most common species were Staphylococcus aureus (343, 45.8% MRSA), Escherichia coli (EC; 288), Pseudomonas aeruginosa (PSA; 221), Klebsiella spp. (KSP; 208), acinetobacters (ACB; 178), enterobacters (155), Streptococcus pneumoniae (SPN; 154, 46.8% penicillin-S), and enterococci (ENT; 137). Among 849 Gram-positive (GP) cocci, linezolid, tigecycline (TIG), daptomycin, and vancomycin provided best antimicrobial coverage (≥99.7% S). Resistance patterns of concern were 0.3% VISA, 15.4% teicoplanin non-S coagulase-negative staphylococci, 1.5% vancomycin-R ENT (all Enterococcus faecium), 1.9% levofloxacin-R β-haemolytic streptococci, and 35.1 and 12.7% ceftriaxone-non-S rates for SPN and viridans group streptococci, respectively. For Gram-negative bacilli, R among Enterobacteriaceae was highest against β-lactams (extended spectrum β-lactamase-phenotype strains at 73.6 and 42.8% in EC and KSP, respectively; carbapenem-R was only 2.1-4.3% with KPC and IMP type enzymes detected in KSP). The widest spectrum agents were cefoperazone/sulbactam (79.5-86.1%), piperacillin/tazobactam (88.9-92.0%), TIG (98.6-100%), amikacin (AMK; 91.8-93.7%), and meropenem (95.7-97.1% S). PSA was most inhibited by AMK (90.5% S) and colistin (COL; 99.5%), with cefepime (67.9%) best among the tested β-lactams. Only COL (100% S) and TIG (MIC90, 2 μg/mL) showed significant potencies against ACB. In conclusion, R among pathogens from 12 Chinese hospitals illustrates several agents active against GP pathogens, but more serious R problems were noted among Enterobacteriaceae, PSA, and ACB. Combination treatment for the latter multidrug-R strains appears necessary, guided by local antibiograms and national surveillance results applying reference methods. © 2013.

  6. Susceptibility rates in Latin American nations: report from a regional resistance surveillance program (2011).

    PubMed

    Jones, Ronald N; Guzman-Blanco, Manuel; Gales, Ana C; Gallegos, Belisario; Castro, Aura Lucia Leal; Martino, Marines Dalla Valle; Vega, Silvio; Zurita, Jeannete; Cepparulo, Mario; Castanheira, Mariana

    2013-01-01

    To establish a resistance (R) surveillance program monitoring antimicrobial susceptibility patterns in Latin America (LATAM; Argentina [ARG], Brazil [BRA], Chile, Colombia [CBA], Costa Rica, Ecuador [ECU], Guatemala [GUA], Mexico [MEX], Panama [PAN], Peru, and Venezuela [VEN]). In 2011, 4979 organisms were collected from 11 nations (20 laboratories) for susceptibility testing in a central laboratory design. Antimicrobials were tested by CLSI methods and results interpreted by CLSI and EUCAST breakpoints. Most common Gram-positive (Staphylococcus aureus [SA, 921], other staphylococci [CoNS; 299], enterococci [218], Streptococcus pneumoniae [SPN; 182], β-haemolytic streptococci [115]) and Gram-negative (E. coli [EC; 644], Klebsiella spp. [KSP; 517], Enterobacters [272], Pseudomonas aeruginosa [PSA; 586], Acinetobacters [ACB; 494]) pathogens were analyzed against linezolid (LZD), vancomycin (VAN), tigecycline (TIG), colistin (COL), cefoperazone/sulbactam (C/S), and amikacin (AMK). MRSA rates varied from 29% (CBA, BRA) to 79% (Peru); but LZD (MIC90, 2mg/L), TIG (MIC90, 0.12mg/L) and VAN (MIC90, 1mg/L) covered all strains. Enterococci showed a 14% VRE rate, highest in BRA and MEX; all inhibited by TIG and daptomycin, but not LZD (three non-susceptible with G2576T mutations or cfr). Penicillin-R among SPN and viridans streptococci was 51.6 and 41.1%, respectively. LZD overall R against Gram-positives was 0.3%. High ESBL rates were observed in EC (54-71%) and KSP (≥50%) from GUA, MEX and Peru, and six nations, respectively. Carbapenem-R in KSP was 9%, highest rates associated with KPC in BRA, CBA, ECU, PAN and VEN; also a NDM-1 in KSP from CBA. AMK, TIG, C/S and carbapenems were the broadest-spectrum agents tested against Enterobacteriaceae. Only COL inhibited >90% of PSA; COL and TIG (≤2mg/L) covered ≥85% of ACB. LATAM nations demonstrated variable levels of antimicrobial R especially among Enterobacteriaceae (β-lactamase-mediated), PSA and ACB. MRSA (48%), VRE (14%) and multidrug-R SPN were also regional therapeutic challenges. Copyright © 2013 Elsevier Editora Ltda. All rights reserved.

  7. Full-scale Transport Controlled Impact Demonstration Program

    NASA Technical Reports Server (NTRS)

    1987-01-01

    The Federal Aviation Administration (FAA) and NASA conducted a full-scale air-to-surface impact-survivable impact demonstration with a remotely piloted transport aircraft on 1 December 1984, at Edwards Air Force Base, California. The test article consisted of experiments, special equipment, and supporting systems, such as antimisting kerosene (AMK), crashworthiness structural/restraint, analytical modeling, cabin fire safety, flight data recorders, post-impact investigation, instrumentation/data acquisition systems, remotely piloted vehicle/flight control systems, range and flight safety provisions, etc. This report describes the aircraft, experiments, systems, activities, and events which lead up to the Controlled Impact Demonstration (CID). An overview of the final unmanned remote control flight and sequence of impact events are delineated. Preliminary post CID observations are presented.

  8. COMPARISON OF EXPERIMENTS TO CFD MODELS FOR MIXING USING DUAL OPPOSING JETS IN TANKS WITH AND WITHOUT INTERNAL OBSTRUCTIONS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Leishear, R.; Poirier, M.; Lee, S.

    2012-06-26

    This paper documents testing methods, statistical data analysis, and a comparison of experimental results to CFD models for blending of fluids, which were blended using a single pump designed with dual opposing nozzles in an eight foot diameter tank. Overall, this research presents new findings in the field of mixing research. Specifically, blending processes were clearly shown to have random, chaotic effects, where possible causal factors such as turbulence, pump fluctuations, and eddies required future evaluation. CFD models were shown to provide reasonable estimates for the average blending times, but large variations -- or scatter -- occurred for blending timesmore » during similar tests. Using this experimental blending time data, the chaotic nature of blending was demonstrated and the variability of blending times with respect to average blending times were shown to increase with system complexity. Prior to this research, the variation in blending times caused discrepancies between CFD models and experiments. This research addressed this discrepancy, and determined statistical correction factors that can be applied to CFD models, and thereby quantified techniques to permit the application of CFD models to complex systems, such as blending. These blending time correction factors for CFD models are comparable to safety factors used in structural design, and compensate variability that cannot be theoretically calculated. To determine these correction factors, research was performed to investigate blending, using a pump with dual opposing jets which re-circulate fluids in the tank to promote blending when fluids are added to the tank. In all, eighty-five tests were performed both in a tank without internal obstructions and a tank with vertical obstructions similar to a tube bank in a heat exchanger. These obstructions provided scale models of vertical cooling coils below the liquid surface for a full scale, liquid radioactive waste storage tank. Also, different jet diameters and different horizontal orientations of the jets were investigated with respect to blending. Two types of blending tests were performed. The first set of eighty-one tests blended small quantities of tracer fluids into solution. Data from these tests were statistically evaluated to determine blending times for the addition of tracer solution to tanks, and blending times were successfully compared to Computational Fluid Dynamics (CFD) models. The second set of four tests blended bulk quantities of solutions of different density and viscosity. For example, in one test a quarter tank of water was added to a three quarters of a tank of a more viscous salt solution. In this case, the blending process was noted to significantly change due to stratification of fluids, and blending times increased substantially. However, CFD models for stratification and the variability of blending times for different density fluids was not pursued, and further research is recommended in the area of blending bulk quantities of fluids. All in all, testing showed that CFD models can be effectively applied if statistically validated through experimental testing, but in the absence of experimental validation CFD model scan be extremely misleading as a basis for design and operation decisions.« less

  9. Remote control of an impact demonstration vehicle

    NASA Technical Reports Server (NTRS)

    Harney, P. F.; Craft, J. B., Jr.; Johnson, R. G.

    1985-01-01

    Uplink and downlink telemetry systems were installed in a Boeing 720 aircraft that was remotely flown from Rogers Dry Lake at Edwards Air Force Base and impacted into a designated crash site on the lake bed. The controlled impact demonstration (CID) program was a joint venture by the National Aeronautics and Space Administration (NASA) and the Federal Aviation Administration (FAA) to test passenger survivability using antimisting kerosene (AMK) to inhibit postcrash fires, improve passenger seats and restraints, and improve fire-retardent materials. The uplink telemetry system was used to remotely control the aircraft and activate onboard systems from takeoff until after impact. Aircraft systems for remote control, aircraft structural response, passenger seat and restraint systems, and anthropomorphic dummy responses were recorded and displayed by the downlink stems. The instrumentation uplink and downlink systems are described.

  10. Laboratory Evaluation of Synthetic Blends of l-(+)-Lactic Acid, Ammonia, and Ketones As Potential Attractants For Aedes aegypti.

    PubMed

    Venkatesh, P M; Sen, A

    2017-12-01

    Attraction of Aedes aegypti to various binary, trinary, and quaternary blends of lactic acid and ketones with or without ammonia was studied using a dual choice olfactometer. A dose dependent attraction was observed in cases of single compounds where cyclopentanone attracted the highest percentage (36.9 ± 1.8%) of Ae. aegypti when tested alone. No significant difference was observed between the attraction levels of trinary and binary blends of lactic acid and acetone or butanone when tested against clear air. However, in competitive bioassays, the trinary blend of lactic acid, acetone, and butanone was significantly preferred over binary blends of individual compounds ( P < 0.05). Acetylacetone was weakly attractive when tested alone but showed additive attraction when blended with lactic acid. However, acetylacetone acted as an attraction inhibitor when blended with other compounds. Cyclopentanone was attractive, but enhancement of attraction was not observed when blended with other components. Addition of ammonia to binary or trinary blends of lactic acid, acetone, and/or butanone did not increase the attraction significantly. In competitive bioassays, the blends containing ammonia were significantly preferred over the blends lacking ammonia ( P < 0.05). This highlights ammonia as an essential component of synthetic blends. A quaternary blend of lactic acid, ammonia, acetone, and butanone was most attractive (65 ± 1.5%) and preferred blend of all other combinations.

  11. 40 CFR 1054.501 - How do I run a valid emission test?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... general testing. For service accumulation, use the test fuel or any commercially available fuel that is... blended fuel or the specified gasoline test fuel with that engine family. (ii) For nonhandheld engines... model year is based on test data collected using the blended fuel, we may use the blended fuel or the...

  12. 40 CFR 1054.501 - How do I run a valid emission test?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... general testing. For service accumulation, use the test fuel or any commercially available fuel that is... blended fuel or the specified gasoline test fuel with that engine family. (ii) For nonhandheld engines... model year is based on test data collected using the blended fuel, we may use the blended fuel or the...

  13. 40 CFR 1054.501 - How do I run a valid emission test?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... general testing. For service accumulation, use the test fuel or any commercially available fuel that is... blended fuel or the specified gasoline test fuel with that engine family. (ii) For nonhandheld engines... model year is based on test data collected using the blended fuel, we may use the blended fuel or the...

  14. 40 CFR 1054.501 - How do I run a valid emission test?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... general testing. For service accumulation, use the test fuel or any commercially available fuel that is... blended fuel or the specified gasoline test fuel with that engine family. (ii) For nonhandheld engines... model year is based on test data collected using the blended fuel, we may use the blended fuel or the...

  15. 40 CFR 1065.725 - High-level ethanol-gasoline blends.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false High-level ethanol-gasoline blends... Calibration Standards § 1065.725 High-level ethanol-gasoline blends. For testing vehicles capable of operating on a high-level ethanol-gasoline blend, create a test fuel as follows: (a) Add ethanol to an E10 fuel...

  16. Antimisting Fuel Research and Development for Commercial Aircraft

    DTIC Science & Technology

    1986-04-01

    applied to the same systems operating with AMK. This finding is contrary to that for forced convection, Boeing said, where AiK is a less effective heat ...Ralph Combariati Port. Authority of NY and NJ JFK International Airport Jamaica, NY 11430 Mr. Edward Conklin Sikorsky Aircraft North Main Street...Charter Oak Boulevard Box 10651 West Hartford, CT 06110-0651 Mr. Stanley Jones Pan American World Airways JFK International Airport New York, NY

  17. Advanced Vehicle Testing Activity: High-Percentage Hydrogen/CNG Blend Ford F-150 Operating Summary - January 2003

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Karner, D.; Francfort, J.E.

    2003-01-22

    Over the past two years, Arizona Public Service, a subsidiary of Pinnacle West Capital Corporation, in cooperation with the U.S. Department of Energy's Advanced Vehicle Testing Activity, tested four gaseous fuel vehicles as part of its alternative fueled vehicle fleet. One vehicle operated initially using compressed natural gas (CNG) and later a blend of CNG and hydrogen. Of the other three vehicles, one was fueled with pure hydrogen and two were fueled with a blend of CNG and hydrogen. The three blended-fuel vehicles were originally equipped with either factory CNG engines or factory gasoline engines that were converted to runmore » CNG fuel. The vehicles were variously modified to operate on blended fuel and were tested using 15 to 50% blends of hydrogen (by volume). The pure-hydrogen-fueled vehicle was converted from gasoline fuel to operate on 100% hydrogen. All vehicles were fueled from the Arizona Public Service's Alternative Fuel Pilot Plant, which was developed to dispense gaseous fuels, including CNG, blends of CNG and hydrogen, and pure hydrogen with up to 99.9999% purity. The primary objective of the test was to evaluate the safety and reliability of operating vehicles on hydrogen and blended fuel, and the interface between the vehicles and the hydrogen fueling infrastructure. A secondary objective was to quantify vehicle emissions, cost, and performance. Over a total of 40,000 fleet test miles, no safety issues were found. Also, significant reductions in emissions were achieved by adding hydrogen to the fuel. This report presents the results of 4,695 miles of testing for one of the blended fuel vehicles, a Ford F-150 pickup truck, operating on up to 50% hydrogen-50% CNG fuel.« less

  18. Advanced Vehicle Testing Activity: Low-Percentage Hydrogen/CNG Blend, Ford F-150 -- Operating Summary

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Karner, D.; Francfort, James Edward

    2003-01-01

    Over the past two years, Arizona Public Service, a subsidiary of Pinnacle West Capital Corporation, in cooperation with the U.S. Department of Energy’s Advanced Vehicle Testing Activity, tested four gaseous fuel vehicles as part of its alternative fueled vehicle fleet. One vehicle operated initially using compressed natural gas (CNG) and later a blend of CNG and hydrogen. Of the other three vehicles, one was fueled with pure hydrogen and two were fueled with a blend of CNG and hydrogen. The three blended-fuel vehicles were originally equipped with either factory CNG engines or factory gasoline engines that were converted to runmore » CNG fuel. The vehicles were variously modified to operate on blended fuel and were tested using 15 to 50% blends of hydrogen (by volume). The pure-hydrogen-fueled vehicle was converted from gasoline fuel to operate on 100% hydrogen. All vehicles were fueled from the Arizona Public Service’s Alternative Fuel Pilot Plant, which was developed to dispense gaseous fuels, including CNG, blends of CNG and hydrogen, and pure hydrogen with up to 99.9999% purity The primary objective of the test was to evaluate the safety and reliability of operating vehicles on hydrogen and blended hydrogen fuel, and the interface between the vehicles and the hydrogen fueling infrastructure. A secondary objective was to quantify vehicle emissions, cost, and performance. Over a total of 40,000 fleet test miles, no safety issues were found. Also, significant reductions in emissions were achieved by adding hydrogen to the fuel. This report presents results of 16,942 miles of testing for one of the blended fuel vehicles, a Ford F-150 pickup truck, operating on up to 30% hydrogen/70% CNG fuel.« less

  19. Advanced Vehicle Testing Activity: Low-Percentage Hydrogen/CNG Blend Ford F-150 Operating Summary - January 2003

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Karner, D.; Francfort, J.E.

    2003-01-22

    Over the past two years, Arizona Public Service, a subsidiary of Pinnacle West Capital Corporation, in cooperation with the U.S. Department of Energy's Advanced Vehicle Testing Activity, tested four gaseous fuel vehicles as part of its alternative fueled vehicle fleet. One vehicle operated initially using compressed natural gas (CNG) and later a blend of CNG and hydrogen. Of the other three vehicles, one was fueled with pure hydrogen and two were fueled with a blend of CNG and hydrogen. The three blended-fuel vehicles were originally equipped with either factory CNG engines or factory gasoline engines that were converted to runmore » CNG fuel. The vehicles were variously modified to operate on blended fuel and were tested using 15 to 50% blends of hydrogen (by volume). The pure-hydrogen-fueled vehicle was converted from gasoline fuel to operate on 100% hydrogen. All vehicles were fueled from the Arizona Public Service's Alternative Fuel Pilot Plant, which was developed to dispense gaseous fuels, including CNG, blends of CNG and hydrogen, and pure hydrogen with up to 99.9999% purity. The primary objective of the test was to evaluate the safety and reliability of operating vehicles on hydrogen and blended hydrogen fuel, and the interface between the vehicles and the hydrogen fueling infrastructure. A secondary objective was to quantify vehicle emissions, cost, and performance. Over a total of 40,000 fleet test miles, no safety issues were found. Also, significant reductions in emissions were achieved by adding hydrogen to the fuel. This report presents results of 16,942 miles of testing for one of the blended fuel vehicles, a Ford F-150 pickup truck, operating on up to 30% hydrogen/70% CNG fuel.« less

  20. Advanced Vehicle Testing Activity: High-Percentage Hydrogen/CNG Blend, Ford F-150 -- Operating Summary

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Don Karner; Francfort, James Edward

    2003-01-01

    Over the past two years, Arizona Public Service, a subsidiary of Pinnacle West Capital Corporation, in cooperation with the U.S. Department of Energy’s Advanced Vehicle Testing Activity, tested four gaseous fuel vehicles as part of its alternative fueled vehicle fleet. One vehicle operated initially using compressed natural gas (CNG) and later a blend of CNG and hydrogen. Of the other three vehicles, one was fueled with pure hydrogen and two were fueled with a blend of CNG and hydrogen. The three blended-fuel vehicles were originally equipped with either factory CNG engines or factory gasoline engines that were converted to runmore » CNG fuel. The vehicles were variously modified to operate on blended fuel and were tested using 15 to 50% blends of hydrogen (by volume). The pure-hydrogen-fueled vehicle was converted from gasoline fuel to operate on 100% hydrogen. All vehicles were fueled from the Arizona Public Service’s Alternative Fuel Pilot Plant, which was developed to dispense gaseous fuels, including CNG, blends of CNG and hydrogen, and pure hydrogen with up to 99.9999% purity. The primary objective of the test was to evaluate the safety and reliability of operating vehicles on hydrogen and blended hydrogen fuel, and the interface between the vehicles and the hydrogen fueling infrastructure. A secondary objective was to quantify vehicle emissions, cost, and performance. Over a total of 40,000 fleet test miles, no safety issues were found. Also, significant reductions in emissions were achieved by adding hydrogen to the fuel. This report presents the results of 4,695 miles of testing for one of the blended fuel vehicles, a Ford F-150 pickup truck, operating on up to 50% hydrogen–50% CNG fuel.« less

  1. Speech Understanding Systems. Summary of Results of the Five-Year Research Effort at Carnegie-Mellon University

    DTIC Science & Technology

    1977-08-01

    EVC’ (EYVR,O) S IV AH2 M CAI (-,0) S IV fEYVL. EYC (EYP.O) (AYL.0) AYC’ (AYR.C) CALCULUS (.- (-,0),-) (K.O) AE31 EL4 (- (-,0),-) (K.0) IH3 L I6 S...SOLVING CARTOGRAPHV CA-’,[ SYSTEM,- CAUSAL REASONING CELl ASAMLIUVLV THEORY CHIECKiNG PROCF-. CHESS CH[qS; PLAY ING PROGnAMk4S CIRCU’IT AI;ALVSiS

  2. NITRO MUSK BOUND TO CARP HEMOGLOBIN ...

    EPA Pesticide Factsheets

    Nitroaromatic compounds including synthetic nitro musks are important raw materials and intermediates in the synthesis of explosives, dyes, and pesticides, pharmaceutical and personal care-products (PPCPs). The nitro musks such as musk xylene (MX) and musk ketone (MK) are extensively used as fragrance ingredients in PPCPs and other commercial toiletries. Identification and quantification of a bound 4-amino-MX (4-AMX) metabolite as well as a 2- amino-MK (2-AMK) metabolite were carried out by gas chromatography-mass spectrometry' (GC/MS), with selected ion monitoring (SIM) in both the electron ionization (ElMS) and electron capture (EC) negative ion chemical ionization (NICIMS) modes. Detection of 4-AMX and 2-AMK occurred after the cysteine adducts in carp hemoglobin, derived from the nitroso metabolites, were released by alkaline hydrolysis. The released metabolites were extracted into n-hexane. The extract was preconcentrated by evaporation, and analyzed by GC-SIM-MS. A comparison between the El and EC approaches was made. EC NICIMS detected both metabolites whereas only 4-AMX was detected by ElMS. The EC NICIMS approach exhibited fewer matrix responses and provided a lower detection limit. Quantitation in both approaches was based on internal standard and a calibration plot. The research focused on in the subtasks is the development and application of state-of the-art technologies to meet the needs of the public, Office of Water, and ORD in the area of Water Q

  3. Engineered Option Treatment of Remediated Nitrate Salts: Surrogate Batch-Blending Testing

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Anast, Kurt Roy

    2016-03-11

    This report provides results from batch-blending test work for remediated nitrate salt (RNS) treatment. Batch blending was identified as a preferred option for blending RNS and unremediated nitrate salt (UNS) material with zeolite to effectively safe the salt/Swheat material identified as ignitable (U.S. Environmental Protection Agency code D001). Blending with zeolite was the preferred remediation option identified in the Options Assessment Report and was originally proposed as the best option for remediation by Clark and Funk in their report, Chemical Reactivity and Recommended Remediation Strategy for Los Alamos Remediated Nitrate Salt (RNS) Wastes, and also found to be a preferredmore » option in the Engineering Options Assessment Report: Nitrate Salt Waste Stream Processing. This test work evaluated equipment and recipe alternatives to achieve effective blending of surrogate waste with zeolite.« less

  4. Applicability of the mixture of bituminous coal and anthracite to conventional pulverized coal firing boiler

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Takano, Shin-Ichi; Kiga, Takashi; Miyamae, Shigehiro

    1994-12-31

    In some future, it is expected for Japanese power stations to be hard to get a high-grade coal like a bituminous coal. We conducted therefore pilot scale tests of pulverized blends of bituminous coal and anthracite using a 1.2MWt tunnel furnace in order to evaluate the applicability of the blends of bituminous coal and anthracite to conventional pulverized coal firing boilers. One kind of bituminous coal and two kinds of anthracite, one was of low ash content and another was of high ash content, were prepared for the test. Previously to pilot scale tests, coal properties and ash properties ofmore » the blends of bituminous coal and anthracite were analyzed to estimate the characteristics of combustion, ash deposition, and so on. In the test, we investigated the combustion efficiency, NOx emission, characteristics of ignition stability and grindability changing the blend rate of anthracite. Results of our study indicated that the critical restrictions on the blending rate of anthracite were unburnt carbon in fly ash and NOx emission as for coals tested. The acceptable limitation on blending rate of anthracite was 10 and 20%, respectively for two kinds of conventional pulverized coal fired boiler. Concerning to the grindability, it became worse with increasing the blending rate of anthracite from grindability test using a roller mill, while it became better estimating from HGI.« less

  5. Advanced Vehicle Testing Activity: Dodge Ram Wagon Van - Hydrogen/CNG Operations Summary - January 2003

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Karner, D.; Francfort, J.E.

    2003-01-16

    Over the past two years, Arizona Public Service, a subsidiary of Pinnacle West Capital Corporation, in cooperation with the U.S. Department of Energy's Advanced Vehicle Testing Activity, tested four gaseous fuel vehicles as part of its alternative fueled vehicle fleet. One vehicle, a Dodge Ram Wagon Van, operated initially using compressed natural gas (CNG) and later a blend of CNG and hydrogen. Of the other three vehicles, one was fueled with pure hydrogen and two were fueled with a blend of CNG and hydrogen. The three blended-fuel vehicles were originally equipped with either factory CNG engines or factory gasoline enginesmore » that were converted to run CNG fuel. The vehicles were variously modified to operate on blended fuel and were tested using 15 to 50% blends of hydrogen (by volume). The pure-hydrogen-fueled vehicle was converted from gasoline fuel to operate on 100% hydrogen. All vehicles were fueled from the Arizona Public Service's Fuel Pilot Plant, which was developed to dispense gaseous fuels, including CNG, blends of CNG and hydrogen, and pure hydrogen with up to 99.9999% purity. The primary objective of the test was to evaluate the safety and reliability of operating vehicles on hydrogen and blended hydrogen fuel, and the interface between the vehicles and the hydrogen fueling infrastructure. A secondary objective was to quantify vehicle emissions, cost, and performance. Over a total of 40,000 fleet test miles, no safety issues were found. Also, significant reductions in emissions were achieved by adding hydrogen to the fuel. This report presents results of 22,816 miles of testing for the Dodge Ram Wagon Van, operating on CNG fuel, and a blended fuel of 15% hydrogen-85% CNG.« less

  6. Advanced Vehicle Testing Activity: Dodge Ram Wagon Van -- Hydrogen/CNG Operations Summary

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Don Karner; Francfort, James Edward

    2003-01-01

    Over the past two years, Arizona Public Service, a subsidiary of Pinnacle West Capital Corporation, in cooperation with the U.S. Department of Energy’s Advanced Vehicle Testing Activity, tested four gaseous fuel vehicles as part of its alternative fueled vehicle fleet. One vehicle, a Dodge Ram Wagon Van, operated initially using compressed natural gas (CNG) and later a blend of CNG and hydrogen. Of the other three vehicles, one was fueled with pure hydrogen and two were fueled with a blend of CNG and hydrogen. The three blended-fuel vehicles were originally equipped with either factory CNG engines or factory gasoline enginesmore » that were converted to run CNG fuel. The vehicles were variously modified to operate on blended fuel and were tested using 15 to 50% blends of hydrogen (by volume). The pure-hydrogen-fueled vehicle was converted from gasoline fuel to operate on 100% hydrogen. All vehicles were fueled from the Arizona Public Service’s Alternative Fuel Pilot Plant, which was developed to dispense gaseous fuels, including CNG, blends of CNG and hydrogen, and pure hydrogen with up to 99.9999% purity. The primary objective of the test was to evaluate the safety and reliability of operating vehicles on hydrogen and blended hydrogen fuel, and the interface between the vehicles and the hydrogen fueling infrastructure. A secondary objective was to quantify vehicle emissions, cost, and performance. Over a total of 40,000 fleet test miles, no safety issues were found. Also, significant reductions in emissions were achieved by adding hydrogen to the fuel. This report presents results of 22,816 miles of testing for the Dodge Ram Wagon Van, operating on CNG fuel, and a blended fuel of 15% hydrogen–85% CNG.« less

  7. Toxicity of Cold Lake Blend and Western Canadian Select dilbits to standard aquatic test species

    EPA Science Inventory

    Dilbits are blends of bitumen and natural gas condensates or crude oils with only limited toxicity data. Two dilbits, Cold Lake Blend and Western Canadian Select, were tested as either unweathered or weathered oils for acute and chronic toxicity to standard freshwater and estuari...

  8. Antimisting fuel breakup and flammability

    NASA Technical Reports Server (NTRS)

    Parikh, P.; Fleeter, R.; Sarohia, V.

    1983-01-01

    The breakup behavior and flammability of antimisting turbine fuels subjected to aerodynamic shear are investigated. Fuels tested were Jet A containing 0.3% FM-9 polymer at various levels of degradation ranging from virgin AMK to neat Jet A. The misting behavior of the fuels was quantified by droplet size distribution measurements. A technique based on high resolution laser photography and digital image processing of photographic records for rapid determination of droplet size distribution was developed. The flammability of flowing droplet-air mixtures was quantified by direct measurements of temperature rise in a flame established in the wake of a continuous ignition source. The temperature rise measurements were correlated with droplet size measurements. The flame anchoring phenomenon associated with the breakup of a liquid fuel in the wake of bluff body was shown to be important in the context of a survivable crash scenario. A pass/fail criterion for flammability testing of antimisting fuels, based on this flame-anchoring phenomenon, was proposed. The role of various ignition sources and their intensity in ignition and post-ignition behavior of antimisting fuels was also investigated.

  9. [Effect of glyceryl triacetate on properties of PLA/PBAT blends].

    PubMed

    Yang, Nan; Wang, Xiyuan; Weng, Yunxuan; Jin, Yujuan; Zhang, Min

    2016-06-25

    Poly lactic acid (PLA)/Poly (butyleneadipate-co-terephthalate)(PBAT) and glyceryl triacetate (GTA) blend were prepared by torque rheometer, and the effect of GTA on thermodynamical performance, mechanical properties and microstructure of PLA/PBAT composites were studied using differential scanning calorimeter(DSC), dynamic mechanical analysis(DMA), universal testing machine, impact testing machine and scanning electron microscope(SEM). After adding GTA, Tg values of the two phases gradually became closer, blends cold crystallization temperature and melting temperature decreased. When with 3 phr GTA, the dispersed phase particle size of PLA/PBAT blend decreased. Mechanics performance test showed that the elongation at break and impact strength of the PLA/PBAT blend was greatly increased with 3 phr GTA, and the elongation at break increased 2.6 times, improved from 17.7% to 64.1%.

  10. Resistance of fly ash-Portland cement blends to thermal shock

    DOE PAGES

    Pyatina, Tatiana; Sugama, Toshifumi

    2015-09-11

    Thermal-shock resistance of high-content fly ash-Portland cement blends was tested in the following ways. Activated and non-activated blends with 80-90 % fly ash F (FAF) were left to set at room temperature, then hydrated for 24 hours at 85°C and 24-more hours at 300°C and tested in five thermal-shock cycles (600°C heat - 25°C water quenching). XRD, and thermal gravimetric analyses, along with calorimetric measurements and SEM-EDX tests demonstrated that the activated blends form more hydrates after 24 hours at 300°C, and achieve a higher short-term compressive strength than do non-activated ones. Sodium meta-silicate and sodaash engendered the concomitant hydrationmore » of OPC and FAF, with the formation of mixed crystalline FAF-OPC hydrates and FAF hydrates, such as garranite, analcime, and wairakite, along with the amorphous FAF hydration products. In SS-activated and non-activated blends separate OPC (tobermorite) and FAF (amorphous gel) hydrates with no mixed crystalline products formed. The compressive strength of all tested blends decreased by nearly 50% after 5 thermal-shock test cycles. These changes in the compressive strength were accompanied by a marked decrease in the intensities of XRD patterns of the crystalline hydrates after the thermalshock. As a result, there was no significant difference in the performance of the blends with different activators« less

  11. Effects of a blended learning module on self-reported learning performances in baccalaureate nursing students.

    PubMed

    Hsu, Li-Ling; Hsieh, Suh-Ing

    2011-11-01

    This article is a report of a quasi-experimental study of the effects of blended modules on nursing students' learning of ethics course content. There is yet to be an empirically supported mix of strategies on which a working blended learning model can be built for nursing education. This was a two-group pretest and post-test quasi-experimental study in 2008 involving a total of 233 students. Two of the five clusters were designated the experimental group to experience a blended learning model, and the rest were designated the control group to be given classroom lectures only. The Case Analysis Attitude Scale, Case Analysis Self-Evaluation Scale, Blended Learning Satisfaction Scale, and Metacognition Scale were used in pretests and post-tests for the students to rate their own performance. In this study, the experimental group did not register significantly higher mean scores on the Case Analysis Attitude Scale at post-test and higher mean ranks on the Case Analysis Self-Evaluation Scale, the Blended Learning Satisfaction Scale, and the Metacognition Scale at post-test than the control group. Moreover, the experimental group registered significant progress in the mean ranks on the Case Analysis Self-Evaluation Scale and the Metacognition Scale from pretest to post-test. No between-subjects effects of four scales at post-test were found. Newly developed course modules, be it blended learning or a combination of traditional and innovative components, should be tested repeatedly for effectiveness and popularity for the purpose of facilitating the ultimate creation of a most effective course module for nursing education. © 2011 Blackwell Publishing Ltd.

  12. Blend uniformity evaluation during continuous mixing in a twin screw granulator by in-line NIR using a moving F-test.

    PubMed

    Fonteyne, Margot; Vercruysse, Jurgen; De Leersnyder, Fien; Besseling, Rut; Gerich, Ad; Oostra, Wim; Remon, Jean Paul; Vervaet, Chris; De Beer, Thomas

    2016-09-07

    This study focuses on the twin screw granulator of a continuous from-powder-to-tablet production line. Whereas powder dosing into the granulation unit is possible from a container of preblended material, a truly continuous process uses several feeders (each one dosing an individual ingredient) and relies on a continuous blending step prior to granulation. The aim of the current study was to investigate the in-line blending capacity of this twin screw granulator, equipped with conveying elements only. The feasibility of in-line NIR (SentroPAT, Sentronic GmbH, Dresden, Germany) spectroscopy for evaluating the blend uniformity of powders after the granulator was tested. Anhydrous theophylline was used as a tracer molecule and was blended with lactose monohydrate. Theophylline and lactose were both fed from a different feeder into the twin screw granulator barrel. Both homogeneous mixtures and mixing experiments with induced errors were investigated. The in-line spectroscopic analyses showed that the twin screw granulator is a useful tool for in-line blending in different conditions. The blend homogeneity was evaluated by means of a novel statistical method being the moving F-test method in which the variance between two blocks of collected NIR spectra is evaluated. The α- and β-error of the moving F-test are controlled by using the appropriate block size of spectra. The moving F-test method showed to be an appropriate calibration and maintenance free method for blend homogeneity evaluation during continuous mixing. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Generator Set Durability Testing Using 25% ATJ Fuel Blend

    DTIC Science & Technology

    2016-02-01

    Table Page Table 1. Chemical & Physical Properties of Evaluated 25% ATJ Blend .................................................... 3 Table 2... Chemical & Physical Properties of Evaluated 25% ATJ Blend .................................................... 4 Table 3. Chemical & Physical...Properties of Evaluated 25% ATJ Blend .................................................... 5 Table 4. Chemical & Physical Properties of Evaluated 25

  14. PLA and single component silicone rubber blends for sub-zero temperature blown film packaging applications

    NASA Astrophysics Data System (ADS)

    Meekum, Utai; Khiansanoi, Apichart

    2018-06-01

    The poly(lactic acid) (PLA) blend with single component silicone rubber in the presence of reactive amino silane coupling agent and polyester polyols plasticizer were studied. The manufacturing of film packaging for sub-zero temperature applications from the PLA blend was the main objective. The mechanical properties, especially the impact strengths, of PLA/silicone blends were significantly depended on the silicone loading. The outstanding impact strengths, tested at sub-zero temperature, of the blend having silicone content of 8.0 phr was achieved. It was chosen as the best candidate for the processability improvement. Adding the talc filler into the PLA/silicone blend to enhance the rheological properties was investigated. The ductility of the talc filled blends were decreased with increasing the filler contents. However, the shear viscosity of the blend was raised with talc loading. The blend loaded with 40 phr of talc filler was justified as the optimal formula for the blown film process testing and it was successfully performed with a few difficulties. The obtained blown film showed relative good flexibility in comparison with LDPE but it has low transparency.

  15. PLA and two components silicon rubber blends aiming for frozen foods packaging applications

    NASA Astrophysics Data System (ADS)

    Meekum, Utai; Khiansanoi, Apichart

    2018-03-01

    Designing of PLA and two components silicone rubber blends was studies. Frozen food packaging application is the main ultimate aim. The statistical method using 23 DOE was conducted. The standard testing methods, in particular impact testing at sub-zero temperature, were performed. The preliminary blend formula comprised 1.0 phr of silane and polyester polyols, respectively, was initially resolved. Then, the optimize the silicone portion in the blends was determined. Blending formula using 8.0 phr of silicone with respect to PLA matrix gave rise to the overall satisfactory properties. 3. TETA was used as the silicone curing agent and reactively blended onto the ingredients. TETA at 0.4 phr, with respect to the silicone, enhanced the mechanical properties, especially flexibility and toughness, of the PLA/silicone blend. Exceeding the optimal TETA loading would cause the chain scission and also the dilution effects. Hence, marginal inferior properties of the blends were be experienced. The preliminary biodegradability investigation found that the PLA/silicone blend initially triggered at the second week. Its degradation rate was likely to be faster than neat PLA.

  16. Tests of blending and correlation of distillate fuel properties

    NASA Technical Reports Server (NTRS)

    Erwin, J.; Bowden, J. N.

    1982-01-01

    The development of a fuel test matrix, results from tests of several blends of distillate aircraft fuels, and the use of correlations in formulation determination during a NASA-sponsored program to identify new aircraft fuels are described. The program was initiated in order to characterize fuel blends which are appropriate for different types of combustors in use and under development. The fuels were required to feature a specified range of properties. Attention is given to fuel volatility, hydrogen content, aromatic content, freezing point, kinematic viscosity, and naphthalene content. Paraffinic and naphtenic base stocks were employed, using alkyl benzene, naphthene benzenes, and naphthalenes to adjust the blend properties. Categories for the test fuels comprised source-controlled and composition controlled fuels. Test results and compositions of various fuels are provided.

  17. A population-based study of first and second-line drug-resistant tuberculosis in a high-burden area of the Mexico/United States border.

    PubMed

    Becerril-Montes, Pola; Said-Fernández, Salvador; Luna-Herrera, Julieta; Caballero-Olín, Guillermo; Enciso-Moreno, José Antonio; Martínez-Rodríguez, Herminia Guadalupe; Padilla-Rivas, Gerardo; Nancy-Garza-Treviño, Elsa; Molina-Salinas, Gloria María

    2013-04-01

    The resistance of 139 Mycobacterium tuberculosis (MTB) isolates from the city of Monterrey, Northeast Mexico, to first and second-line anti-TB drugs was analysed. A total of 73 isolates were susceptible and 66 were resistant to anti-TB drugs. Monoresistance to streptomycin, isoniazid (INH) and ethambutol was observed in 29 cases. Resistance to INH was found in 52 cases and in 29 cases INH resistance was combined with resistance to two or three drugs. A total of 24 isolates were multidrug-resistant (MDR) resistant to at least INH and rifampicin and 11 MDR cases were resistant to five drugs. The proportion of MDR-TB among new TB cases in our target population was 0.72% (1/139 cases). The proportion of MDR-TB among previously treated cases was 25.18% (35/139 cases). The 13 polyresistant and 24 MDR isolates were assayed against the following seven second-line drugs: amikacin (AMK), kanamycin (KAN), capreomycin (CAP), clofazimine (CLF), ethionamide (ETH), ofloxacin (OFL) and cycloserine (CLS). Resistance to CLF, OFL or CLS was not observed. Resistance was detected to ETH (10.80%) and to AMK (2.70%), KAN (2.70%) and CAP (2.70%). One isolate of MDR with primary resistance was also resistant to three second-line drugs. Monterrey has a high prevalence of MDR-TB among previously treated cases and extensively drug-resistant-MTB strains may soon appear.

  18. A population-based study of first and second-line drug-resistant tuberculosis in a high-burden area of the Mexico/United States border

    PubMed Central

    Becerril-Montes, Pola; Said-Fernández, Salvador; Luna-Herrera, Julieta; Caballero-Olín, Guillermo; Enciso-Moreno, José Antonio; Martínez-Rodríguez, Herminia Guadalupe; Padilla-Rivas, Gerardo; Nancy-Garza-Treviño, Elsa; Molina-Salinas, Gloria María

    2013-01-01

    The resistance of 139 Mycobacterium tuberculosis (MTB) isolates from the city of Monterrey, Northeast Mexico, to first and second-line anti-TB drugs was analysed. A total of 73 isolates were susceptible and 66 were resistant to anti-TB drugs. Monoresistance to streptomycin, isoniazid (INH) and ethambutol was observed in 29 cases. Resistance to INH was found in 52 cases and in 29 cases INH resistance was combined with resistance to two or three drugs. A total of 24 isolates were multidrug-resistant (MDR) resistant to at least INH and rifampicin and 11 MDR cases were resistant to five drugs. The proportion of MDR-TB among new TB cases in our target population was 0.72% (1/139 cases). The proportion of MDR-TB among previously treated cases was 25.18% (35/139 cases). The 13 polyresistant and 24 MDR isolates were assayed against the following seven second-line drugs: amikacin (AMK), kanamycin (KAN), capreomycin (CAP), clofazimine (CLF), ethionamide (ETH), ofloxacin (OFL) and cycloserine (CLS). Resistance to CLF, OFL or CLS was not observed. Resistance was detected to ETH (10.80%) and to AMK (2.70%), KAN (2.70%) and CAP (2.70%). One isolate of MDR with primary resistance was also resistant to three second-line drugs. Monterrey has a high prevalence of MDR-TB among previously treated cases and extensively drug-resistant-MTB strains may soon appear. PMID:23579794

  19. NITRO MUSK ADDUCTS OF RAINBOW TROUT ...

    EPA Pesticide Factsheets

    Rainbow trout and other fish species can serve as 'sentinel' species for the assessment of ecological status and the presence of certain environmental contaminants. As such they act as bioindicators of exposure. Here we present seminal data regarding dose-response and toxicokinetics of trout hemoglobin adduct formation from exposure to nitro musks that are frequently used as fragrance ingredients in formulations of personal care products. Hemoglobin adducts serve as biomarkers of exposure of the sentinel species as we have shown in previous studies of hemoglobin adducts formed in trout and environmental carp exposed to musk xylene (MX) and musk ketone (MK). Gas chromatography-electron capture negative ion chemical ionization-mass spectrometry (GC-NICI-MS) employing selected ion monitoring is used to measure 4-amino-MX (4-AMX), 2-amino-MX (2-AMX), and 2-amino-MK (2-AMK) released by alkaline hydrolysis from the sulfinamide adducts of hemoglobin. Dose-response and toxicokinetics were investigated using this sensitive method for analysis of these metabolites. In the dose-response investigation, the concentrations of 4-AMX and 2-2AMX are observed to pass through a maximum at 0.10 mg/g. In the case of 2-AMK, the adduct concentration is almost the same at dosages in the range of 0.030 to 0.10 mg/g. For toxicokinetics, the concentration of the metabolites in the Hb reaches a maximum in the 3-day sample after administration of MX or MK. Further elimination of the metabo

  20. 40 CFR 1060.501 - General testing provisions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... that requires a blend of gasoline and ethanol, blend this grade of gasoline with fuel-grade ethanol... measure the ethanol concentration of such blended fuels and may instead calculate the blended composition by assuming that the ethanol is pure and mixes perfectly with the base fuel. For example, if you mix...

  1. 40 CFR 1060.501 - General testing provisions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... that requires a blend of gasoline and ethanol, blend this grade of gasoline with fuel-grade ethanol... measure the ethanol concentration of such blended fuels and may instead calculate the blended composition by assuming that the ethanol is pure and mixes perfectly with the base fuel. For example, if you mix...

  2. 40 CFR 1060.501 - General testing provisions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... that requires a blend of gasoline and ethanol, blend this grade of gasoline with fuel-grade ethanol... measure the ethanol concentration of such blended fuels and may instead calculate the blended composition by assuming that the ethanol is pure and mixes perfectly with the base fuel. For example, if you mix...

  3. 40 CFR 1060.501 - General testing provisions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... that requires a blend of gasoline and ethanol, blend this grade of gasoline with fuel-grade ethanol... measure the ethanol concentration of such blended fuels and may instead calculate the blended composition by assuming that the ethanol is pure and mixes perfectly with the base fuel. For example, if you mix...

  4. 40 CFR 1060.501 - General testing provisions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... that requires a blend of gasoline and ethanol, blend this grade of gasoline with fuel-grade ethanol... measure the ethanol concentration of such blended fuels and may instead calculate the blended composition by assuming that the ethanol is pure and mixes perfectly with the base fuel. For example, if you mix...

  5. 40 CFR 60.583 - Test methods and procedures.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... must be used in combination with plant blending records (if plant blending is done) or inventory... the inks, standard gas chromatographic techniques may be used to identify and quantify these solvents...' formulation data along with plant blending records (if plant blending is done) may be used to determine VOC...

  6. Novel Blend for Producing Porous Chitosan-Based Films Suitable for Biomedical Applications

    PubMed Central

    Nady, Norhan; Kandil, Sherif H.

    2018-01-01

    In this work, a chitosan–gelatin–ferulic acid blend was used in different ratios for preparing novel films that can be used in biomedical applications. Both acetic and formic acid were tested as solvents for the chitosan–gelatin–ferulic acid blend. Glycerol was tested as a plasticizer. The thickness, mechanical strength, static water contact angle and water uptake of the prepared films were determined. Also, the prepared films were characterized using different analysis techniques such as Fourier transform infrared spectroscopy (FT-IR) analysis, X-ray diffraction (XRD), thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Acetic acid produced continuous compact surfaces that are not recommended for testing in biomedical applications. The plasticized chitosan–gelatin–ferulic acid blend, using formic acid solvent, produced novel hexagonal porous films with a pore size of around 10–14 µm. This blend is recommended for preparing films (scaffolds) for testing in biomedical applications as it has the advantage of a decreased thickness. PMID:29301357

  7. Evaluation of 25-Percent ATJ Fuel Blends in the John Deere 4045HF 280 Engine

    DTIC Science & Technology

    2014-08-01

    25% ATJ Blend ........ 26 Figure 16 . THC Emissions, Pre-Test, Ambient Temperature ...................................................... 28 Figure...17 . THC Emissions, Pre-Test, Desert Temperature ......................................................... 28 Figure 18 . NOx Emissions, Pre-Test...Emissions, Pre-Test, Desert Temperature (Scaled) ............................................. 32 Figure 23 . THC Emissions, Post-Test, Ambient

  8. Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends.

    PubMed

    Altiparmak, Duran; Keskin, Ali; Koca, Atilla; Gürü, Metin

    2007-01-01

    In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load condition. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO(x) emissions increased up to 30% with the new fuel blends. The smoke opacity did not vary significantly.

  9. Damage initiated self-healing in ionomer blends

    NASA Astrophysics Data System (ADS)

    Rahman, Md. Arifur; Penco, Maurizio; Spagnoli, Gloria; Peroni, Isabella; Ramorino, Giorgio; Sartore, Luciana; Bignotti, Fabio; Landro, Luca Di

    2012-07-01

    The development and understanding of self-healing mechanisms have been investigated in blends of ionomers (Poly(ethyelene-co-methacrylic acid), sodium & zinc ions) (EMNa & EMZn) containing both elastomers (Epoxidized natural rubbers (ENR) and cis-1,4-Polyisoprene (PISP)) and crystalline component (Poly(vinly alcohol-co-ethylene) [PVAcE]) as secondary phases. All the blends were prepared by melt-blending and self-healing behavior was studied in ballistic puncture tests. Self-healing behavior of each material was evaluated by observing the impact zones under a stereo-optical microscope and the micrographic results were further supported by the fluid flow test in the punctured zones. Interestingly, ENR50 blends of sodium ion containing ionomers exhibited complete self-repairing behavior while zinc ion containing ionomer showed limited mending but EMNa/ENR25 and EMNa/PISP blends did not show any self-healing behavior following the damage. On the other hand, a composition dependent healing behavior was observed in the EMNa/PVAcE blends where healing was observed up to 30wt% PVAcE containing blends. The chemical structure studied by FTIR analysis showed that both ion content of ionomer and functionality of ENR have significant influence on the self-repairing behavior of blends. TEM analysis revealed that self-healing occurs in the blends when the dispersed phase has a dimension of 100 to 400 nm.

  10. Empirical Study of the Stability of Biodiesel and Biodiesel Blends: Milestone Report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    McCormick, R. L.; Westbrook, S. R.

    2007-05-01

    The objective of this work was to develop a database that supports specific proposals for a stability test and specification for biodiesel and biodiesel blends. B100 samples from 19 biodiesel producers were obtained in December of 2005 and January of 2006 and tested for stability. Eight of these samples were then selected for additional study, including long-term storage tests and blending at 5% and 20% with a number of ultra-low sulfur diesel fuels.

  11. [Near infrared analysis of blending homogeneity of Chinese medicine formula particles based on moving window F test method].

    PubMed

    Yang, Chan; Xu, Bing; Zhang, Zhi-Qiang; Wang, Xin; Shi, Xin-Yuan; Fu, Jing; Qiao, Yan-Jiang

    2016-10-01

    Blending uniformity is essential to ensure the homogeneity of Chinese medicine formula particles within each batch. This study was based on the blending process of ebony spray dried powder and dextrin(the proportion of dextrin was 10%),in which the analysis of near infrared (NIR) diffuse reflectance spectra was collected from six different sampling points in combination with moving window F test method in order to assess the blending uniformity of the blending process.The method was validated by the changes of citric acid content determined by the HPLC. The results of moving window F test method showed that the ebony spray dried powder and dextrin was homogeneous during 200-300 r and was segregated during 300-400 r. An advantage of this method is that the threshold value is defined statistically, not empirically and thus does not suffer from threshold ambiguities in common with the moving block standard deviatiun (MBSD). And this method could be employed to monitor other blending process of Chinese medicine powders on line. Copyright© by the Chinese Pharmaceutical Association.

  12. Mechanical properties, morphology, and hydrolytic degradation behavior of polylactic acid / natural rubber blends

    NASA Astrophysics Data System (ADS)

    Buys, Y. F.; Aznan, A. N. A.; Anuar, H.

    2018-01-01

    Due to its biodegradability and renewability, polylactic acid (PLA) has been receiving enormous attention as a potential candidate to replace petroleum based polymers. However, PLA has limitation due to its inherent brittleness. In order to overcome this limitation, blending PLA with elastomeric materials such as natural rubber (NR) are commonly reported. In previous, several researches on PLA/NR blend had been reported, with most of them evaluated the mechanical properties. On the other hand, study of degradation behavior is significance of importance, as controlling materials degradation is required in some applications. This research studied the effect of blend composition on mechanical properties, morphology development, and hydrolytic degradation behavior of PLA/NR blends. Various compositions of PLA/NR blends were prepared by melt blending technique. Tensile test and impact test of the blends were performed to evaluate the mechanical properties. Addition of NR improved the elongation at break and impact strength of the blends, but reduced the tensile strength and stiffness of the specimens. Dynamic Mechanical Analysis (DMA) measurements of the blends displayed two peaks at temperature -70˚C which corresponded to T g of NR and 65˚C which corresponded to T g of PLA. Field Emission Scanning Electron Microscopy (FE-SEM) micrograph of 70/30 PLA/NR specimen also showed two distinct phases, which lead to indication that PLA/NR blends are immiscible. Hydrolytic degradation behavior was evaluated by measuring the remaining weight of the samples immersed in sodium hydroxide solution for a predetermined times. It was shown that the degradation behavior of PLA/NR blends is affected by composition of the blends, with 100 PLA and 70/30 PLA/NR blend showed the fastest degradation rate and 100 NR displayed the slowest one.

  13. Combustion performance of pyrolysis oil/ethanol blends in a residential-scale oil-fired boiler

    USDA-ARS?s Scientific Manuscript database

    A 40 kWth oil-fired commercial boiler was fueled with blends of biomass pyrolysis oil (py-oil) and ethanol to determine the feasibility of using these blends as a replacement for fuel oil in home heating applications. An optimal set of test parameters was determined for the combustion of these blend...

  14. Blended learning in K-12 mathematics and science instruction -- An exploratory study

    NASA Astrophysics Data System (ADS)

    Schmidt, Jason

    Blended learning has developed into a hot topic in education over the past several years. Flipped classrooms, online learning environments, and the use of technology to deliver educational content using rich media continue to garner national attention. While generally well accepted and researched in post-secondary education, not much research has focused on blended learning in elementary, middle, and high schools. This thesis is an exploratory study to begin to determine if students and teachers like blended learning and whether or not it affects the amount of time they spend in math and science. Standardized achievement test data were also analyzed to determine if blended learning had any effect on test scores. Based on student and teacher surveys, this population seems to like blended learning and to work more efficiently in this environment. There is no evidence from this study to support any effect on student achievement.

  15. Drive cycle analysis of butanol/diesel blends in a light-duty vehicle.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Miers, S. A.; Carlson, R. W.; McConnell, S. S.

    2008-10-01

    The potential exists to displace a portion of the petroleum diesel demand with butanol and positively impact engine-out particulate matter. As a preliminary investigation, 20% and 40% by volume blends of butanol with ultra low sulfur diesel fuel were operated in a 1999 Mercedes Benz C220 turbo diesel vehicle (Euro III compliant). Cold and hot start urban as well as highway drive cycle tests were performed for the two blends of butanol and compared to diesel fuel. In addition, 35 MPH and 55 MPH steady-state tests were conducted under varying road loads for the two fuel blends. Exhaust gas emissions,more » fuel consumption, and intake and exhaust temperatures were acquired for each test condition. Filter smoke numbers were also acquired during the steady-state tests.« less

  16. Biodegradation test of SPS-LS blends as polymer electrolyte membrane fuel cells

    NASA Astrophysics Data System (ADS)

    Putri, Zufira; Arcana, I. Made

    2014-03-01

    Sulfonated polystyrene (SPS) can be applied as a proton exchange membrane fuel cell due to its fairly good chemical stability. In order to be applied as polymer electrolyte membrane fuel cells (PEMFCs), membrane polymer should have a good ionic conductivity, high proton conductivity, and high mechanical strength. Lignosulfonate (LS) is a complex biopolymer which has crosslinks and sulfonate groups. SPS-LS blends with addition of SiO2 are used to increase the proton conductivity and to improve the mechanical properties and thermal stability. However, the biodegradation test of SPS-LS blends is required to determine whether the application of these membranes to be applied as an environmentally friendly membrane. In this study, had been done the synthesis of SPS, biodegradability test of SPS-LS blends with variations of LS and SiO2 compositions. The biodegradation test was carried out in solid medium of Luria Bertani (LB) with an activated sludge used as a source of microorganism at incubation temperature of 37°C. Based on the results obtained indicated that SPS-LS-SiO2 blends are more decomposed by microorganism than SPS-LS blends. This result is supported by analysis of weight reduction percentage, functional groups with Fourier Transform Infrared (FTIR) Spectroscopy, and morphological surface with Scanning Electron Microscopy (SEM).

  17. Test Operations Procedure (TOP) 01-1-025 Camouflage Performance Testing Using Observers

    DTIC Science & Technology

    2016-05-05

    15. SUBJECT TERMS camouflage, detection, blending , signatures 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT SAR 18...21 6.2 Blending Data... learning effect on observers. If military personnel are required for testing, determine if Military Occupational Specialty (MOS) qualified Soldier

  18. Shigellosis Outbreak in Al Batinah South Governorate, Oman

    PubMed Central

    Abaidani, Idris; Raju, Prasanna A.; Al-Shualli, Issa; Al-Sa’di, Khalid; Al-Shaqsi, Nasser; Al-Khatri, Amer

    2015-01-01

    Objectives: An outbreak of acute gastroenteritis due to Shigella flexneri occurred in August 2012 in the catchment area of the Wadi Sahtan Health Center in Rustaq, Al Batinah South Governorate, Oman. The aim of this study was to discover possible causes of this outbreak in the villages of Fassa, Rogh and Amk and to measure the risk of exposure among cases and controls. Methods: A case-control study was conducted in September 2012 in Fassa, Rogh and Amk. All households in the three villages were interviewed. Case and control households were compared to determine possible exposure avenues, including place of residence, source of drinking water, hand hygiene levels and practices related to drinking water, food preparation and environmental sanitation. Results: Residing in Fassa (P <0.0001; odds ratio [OR] = 4.86, 95% confidence interval [CI] = 2.22–10.63) and average hand hygiene practices (P = 0.008; OR = 13.97, 95% CI = 1.58–123.36) were associated with an increased risk of contracting shigellosis. No significant differences were found with regards to the other exposure avenues. Conclusion: This was the first study conducted in Oman regarding an outbreak of shigellosis in a community setting. The only variables that significantly impacted the risk of acute gastroenteritis were residing in Fassa and average hand hygiene practices. The source of the outbreak could not be identified. However, septic tank sanitation and water and food consumption practices were not satisfactory in the studied villages. These need to be addressed to prevent similar outbreaks of acute gastroenteritis in this region in the future. PMID:26357558

  19. Blended learning pedagogy designed for communication module among undergraduate nursing students: A quasi-experimental study.

    PubMed

    Shorey, Shefaly; Kowitlawakul, Yanika; Devi, M Kamala; Chen, Hui-Chen; Soong, Swee Kit Alan; Ang, Emily

    2018-02-01

    Effective communication is important for nurse and patient outcomes. Nursing students often feel unprepared to communicate effectively with patients and other healthcare workers within the clinical environment. Blended learning pedagogy-based communication skills training can provide an alternative to traditional methods of teaching to enhance students' satisfaction and self-efficacy levels in communicating with others. To examine the effectiveness of blended learning pedagogy in a redesigned communication module among nursing undergraduates in enhancing their satisfaction levels and attitudes towards learning communication module as well as self-efficacy in communication. A single group pre-test and post-test quasi-experimental design was adopted. Data were collected from August 2016 to November 2016 from 124 nursing undergraduates from a leading nursing school. Blended learning pedagogy was adopted to redesign a communication module that offered a wide array of learning opportunities via face-to-face classroom and online sessions. Validated and reliable instruments were used to measure satisfaction levels with blended learning pedagogy, attitudes towards learning communication, and communication self-efficacy. Descriptive and inferential statistics were used to analyze the data. Participants had enhanced satisfaction levels with blended learning pedagogy, better attitudes in learning communication skills, and improved communication self-efficacies at posttest (week 13 of the semester) when compared with their pre-test scores (week one of the semester). Participants scored higher in the Blended Learning Satisfaction Scale, the Communication Skills Attitude Scale, and the communication skills subscale of the Nursing Students Self-Efficacy Scale. Blended learning pedagogy can be effectively used in facilitating communication modules and enhancing student outcomes among nursing undergraduates. The long-term effectiveness of using blended learning pedagogy in facilitating communication modules should be evaluated from students' and patients' perspectives. Additionally, the technology should be constantly improved by incorporating more interactive functions and should be tested to accommodate the learners' needs. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Autonomous healing materials based on epoxidized natural rubber and ethylene methacrylic acid ionomers

    NASA Astrophysics Data System (ADS)

    Arifur Rahman, Md; Penco, Maurizio; Peroni, Isabella; Ramorino, Giorgio; Janszen, Gerardus; Di Landro, Luca

    2012-03-01

    The development of autonomous healing material has an enormous scientific and technological interest. In this context, this research work deals with the investigation of autonomous healing behavior of epoxidized natural rubber (ENR) and its blends with ethylene methacrylic acid ionomers. The autonomous healing behavior of ENR and its blends containing two different ionomers [poly(ethylene-co-methacrylic acid sodium salt) (EMNa) and poly(ethylene-co-methacrylic acid zinc salt) (EMZn)] has been studied by ballistic puncture tests. Interestingly, EMNa/ENR blends exhibit complete healing just after the ballistic test but EMZn/ENR blends do not show full self-repairing. The healing efficiency has been evaluated by optical microscopy and a depressurized air-flow test. The healing mechanism has been investigated by characterizing thermal and mechanical properties of the blends. The chemical structure studied by FTIR and thermal analysis show that the ion content of ionomers and functionality of ENR has a significant influence on the self-healing behavior.

  1. Investigation of sources, properties and preparation of distillate test fuels

    NASA Technical Reports Server (NTRS)

    Bowden, J. N.; Erwin, J.

    1983-01-01

    Distillate test fuel blends were generated for prescribed variations in composition and physical properties. Fuels covering a wide range in properties and composition which would provide a matrix of fuels for possible use in future combustion research programs were identified. Except for tetralin the blending components were all from typical refinery streams. Property variation blends span a boiling range within 150 C to 335 C, freezing point -23 C to -43 C, aromatic content 20 to 50 volume percent, hydrogen content 11.8 to 14.2 mass percent, viscosity 4 and 11 cSt (-20 C), and naphthalenes 8 and 16 volume percent. Composition variation blends were made with two base stocks, one paraffinic and the other napthenic. To each base stock was added each of three aromatic type fuels (alkyl benzenes, tetralin, and naphthalenes) for assigned initial boiling point, final boiling point, and hydrogen content. The hydrogen content was 13.5 mass percent for the paraffinic base stock blends and 12.5 mass percent and 11.5 mass percent for the naphthenic base stock blends. Sample 5-gallon quantities of all blends were prepared and analyzed.

  2. Compatibility Studies of Hydrogen Peroxide and a New Hypergolic Fuel Blend

    NASA Technical Reports Server (NTRS)

    Baldridge, Jennifer; Villegas, Yvonne

    2002-01-01

    Several preliminary materials compatibility studies have been conducted to determine the practicality of a new hypergolic fuel system. Hypergolic fuel ignites spontaneously as the oxidizer decomposes and releases energy in the presence of the fuel. The bipropellant system tested consists of high-test hydrogen peroxide (HTP) and a liquid fuel blend consisting of a hydrocarbon fuel, an ignition enhancer and a transition metal catalyst. In order for further testing of the new fuel blend to take place, some basic materials compatibility and HTP decomposition studies must be accomplished. The thermal decomposition rate of HTP was tested using gas evolution and isothermal microcalorimetry (IMC). Materials were analyzed for compatibility with hydrogen peroxide including a study of the affect welding has on stainless steel elemental composition and its relation to HTP decomposition. Compatibility studies of valve materials in the fuel blend were performed to determine the corrosion resistance of the materials.

  3. Experimental investigation on Performance and Emission Characteristics of J20, P20, N20 Biodiesel blends and Sound Characteristics of P20 Biodiesel blend Used in Single Cylinder Diesel Engine

    NASA Astrophysics Data System (ADS)

    rajasekar, R.; karthik, N.; Xavier, Goldwin

    2017-05-01

    Present work provides the effect of biodiesel blends and Sound Characteristics of P20 Biodiesel blend compared with Performance and emission Characteristics of diesel. Methods and analysis biodiesel blends was prepared by the Transesterification Process. Experiments were conducted in single cylinder constant speed direct injection diesel engine for various test fuels. Research is mainly focused on pongamia oil. It was observed that a 20% Pongamia oil blends and its properties were similar to diesel. The results showed that 20% Pongamia oil blends gave better performance, less in noise and emission compared with ester of Jatropha and neem oil blends. Hence Pongamia blends can be used in existing diesel engine without compromising the engine performance.

  4. Sample Results From The Extraction, Scrub, And Strip Test For The Blended NGS Solvent

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Washington, A. L. II; Peters, T. B.

    This report summarizes the results of the extraction, scrub, and strip testing for the September 2013 sampling of the Next Generation Solvent (NGS) Blended solvent from the Modular Caustic Side-Solvent Extraction Unit (MCU) Solvent Hold Tank. MCU is in the process of transitioning from the BOBCalixC6 solvent to the NGS Blend solvent. As part of that transition, MCU has intentionally created a blended solvent to be processed using the Salt Batch program. This sample represents the first sample received from that blended solvent. There were two ESS tests performed where NGS blended solvent performance was assessed using either the Tankmore » 21 material utilized in the Salt Batch 7 analyses or a simulant waste material used in the V-5/V-10 contactor testing. This report tabulates the temperature corrected cesium distribution, or D Cs values, step recovery percentage, and actual temperatures recorded during the experiment. This report also identifies the sample receipt date, preparation method, and analysis performed in the accumulation of the listed values. The calculated extraction D Cs values using the Tank 21H material and simulant are 59.4 and 53.8, respectively. The DCs values for two scrub and three strip processes for the Tank 21 material are 4.58, 2.91, 0.00184, 0.0252, and 0.00575, respectively. The D-values for two scrub and three strip processes for the simulant are 3.47, 2.18, 0.00468, 0.00057, and 0.00572, respectively. These values are similar to previous measurements of Salt Batch 7 feed with lab-prepared blended solvent. These numbers are considered compatible to allow simulant testing to be completed in place of actual waste due to the limited availability of feed material.« less

  5. Thermal Stability Testing of Fischer-Tropsch Fuel and Various Blends with Jet A, as Well as Aromatic Blend Additives

    NASA Technical Reports Server (NTRS)

    Klettlinger, J.; Rich, R.; Yen, C.; Surgenor, A.

    2011-01-01

    Fischer-Tropsch (F-T) jet fuel composition differs from petroleum-based, conventional commercial jet fuel because of differences in feedstock and production methodology. Fischer-Tropsch fuel typically has a lower aromatic and sulfur content and consists primarily of iso and normal parafins. The ASTM D3241 specification for Jet Fuel Thermal Oxidation Test (JFTOT) break point testing method was used to test the breakpoint of a baseline conventional Jet A, a commercial grade F-T jet fuel, and various blends of this F-T fuel in Jet A. The testing completed in this report was supported by the NASA Fundamental Aeronautics Subsonics Fixed Wing Project.

  6. Parasitic wasp females are attracted to blends of host-induced plant volatiles: do qualitative and quantitative differences in the blend matter?

    PubMed Central

    Uefune, Masayoshi; Kugimiya, Soichi; Ozawa, Rika; Takabayashi, Junji

    2013-01-01

    Naïve Cotesia vestalis wasps, parasitoids of diamondback moth (DBM) larvae, are attracted to a synthetic blend (Blend A) of host-induced plant volatiles composed of sabinene, n-heptanal, α-pinene, and ( Z)-3-hexenyl acetate, in a ratio of 1.8:1.3:2.0:3.0. We studied whether qualitative (adding ( R)-limonene: Blend B) or quantitative changes (changing ratios: Blend C) to Blend A affected the olfactory response of C. vestalis in the background of intact komatsuna plant volatiles. Naïve wasps showed equal preference to Blends A and B and Blends A and C in two-choice tests. Wasps with oviposition experience in the presence of Blend B preferred Blend B over Blend A, while wasps that had oviposited without a volatile blend showed no preference between the two. Likewise, wasps that had starvation experience in the presence of Blend B preferred Blend A over Blend B, while wasps that had starved without a volatile blend showed no preference between the two. Wasps that had oviposition experience either with or without Blend A showed equal preferences between Blends C and A. However, wasps that had starvation experience in the presence of Blend A preferred Blend C over Blend A, while those that starved without a volatile blend showed equal preferences between the two. By manipulating quality and quantity of the synthetic attractants, we showed to what extent C. vestalis could discriminate/learn slight differences between blends that were all, in principle, attractive. PMID:24358892

  7. Preparation and characterization of reactive blends of poly(lactic acid), poly(ethylene-co-vinyl alcohol), and poly(ethylene-co-glycidyl methacrylate)

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Warangkhana, Phromma; Rathanawan, Magaraphan, E-mail: rathanawan.k@chula.ac.th; Jana Sadhan, C., E-mail: janas@uakron.edu

    The ternary blends of poly(lactic acid) (PLA), poly(ethylene-co-vinyl alcohol) (EVOH), and poly(ethylene-co-glycidyl methacrylate) (EGMA) were prepared. The role of EGMA as a compatibilizer was evaluated. The weight ratio of PLA:EVOH was 80:20 and the EGMA loadings were varied from 5-20 phr. The blends were characterized as follows: thermal properties by differential scanning calorimetry, morphology by scanning electron microscopy, and mechanical properties by pendulum impact tester, and universal testing machine. The glass transition temperature of PLA blends did not change much when compared with that of PLA. The blends of PLA/EGMA and EVOH/EGMA showed EGMA dispersed droplets where the latter ledmore » to poor impact properties. However, the tensile elongation at break and tensile toughness substantially increased upon addition of EGMA to blends of PLA and EVOH. It was noted in tensile test samples that both PLA and EVOH domains fibrillated significantly to produce toughness.« less

  8. Impact of biodiesel and renewable diesel on emissions of regulated pollutants and greenhouse gases on a 2000 heavy duty diesel truck

    NASA Astrophysics Data System (ADS)

    Na, Kwangsam; Biswas, Subhasis; Robertson, William; Sahay, Keshav; Okamoto, Robert; Mitchell, Alexander; Lemieux, Sharon

    2015-04-01

    As part of a broad evaluation of the environmental impacts of biodiesel and renewable diesel as alternative motor fuels and fuel blends in California, the California Air Resources Board's (CARB) Heavy-duty Diesel Emission Testing Laboratory conducted chassis dynamometer exhaust emission measurements on in-use heavy-heavy-duty diesel trucks (HHDDT). The results presented here detail the impact of biodiesel and renewable diesel fuels and fuel blends as compared to CARB ULSD on particulate matter (PM), regulated gases, and two greenhouse gases emissions from a HHDDT with a 2000 C15 Caterpillar engine with no exhaust after treatment devices. This vehicle was tested over the Urban Dynamometer Driving Schedule (UDDS) and the cruise portion of the California HHDDT driving schedule. Three neat blend stocks (soy-based and animal-based fatty acid methyl ester (FAME) biodiesels, and a renewable diesel) and CARB-certified ultra-low sulfur diesel (CARB ULSD) along with their 20% and 50% blends (blended with CARB ULSD) were tested. The effects of blend level on emission characteristics were discussed on g·km-1 basis. The results showed that PM, total hydrocarbon (THC), and carbon monoxide (CO) emissions were dependent on driving cycles, showing higher emissions for the UDDS cycles with medium load than the highway cruise cycle with high load on per km basis. When comparing CARB ULSD to biodiesels and renewable diesel blends, it was observed that the PM, THC, and CO emissions decreased with increasing blend levels regardless of the driving cycles. Note that biodiesel blends showed higher degree of emission reductions for PM, THC, and CO than renewable diesel blends. Both biodiesels and renewable diesel blends effectively reduced PM emissions, mainly due to reduction in elemental carbon emissions (EC), however no readily apparent reductions in organic carbon (OC) emissions were observed. When compared to CARB ULSD, soy- and animal-based biodiesel blends showed statistically significant increases in nitrogen oxides (NOx) emissions for 50% or higher biodiesel blends. The 20% blends of the biodiesels showed no statistically significant effect on NOx emissions on any cycle. In contrast, renewable diesel slightly decreased NOx emissions and the degree of reduction was statistically significant for 50% or higher blends over the UDDS cycle, but not at the 20% blends. The highway cruise cycles did not show a statistically strong NOx emission trend with increasing blend level of renewable diesel. Biodiesel and renewable fuel impacts on two greenhouse gases, CO2 and N2O emissions were of lower magnitude when compared to other regulated pollutants emissions, showing a change in their emissions within approximately ±3% from the CARB ULSD.

  9. Biodegradation test of SPS-LS blends as polymer electrolyte membrane fuel cells

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Putri, Zufira, E-mail: zufira.putri@gmail.com, E-mail: arcana@chem.itb.ac.id; Arcana, I Made, E-mail: zufira.putri@gmail.com, E-mail: arcana@chem.itb.ac.id

    Sulfonated polystyrene (SPS) can be applied as a proton exchange membrane fuel cell due to its fairly good chemical stability. In order to be applied as polymer electrolyte membrane fuel cells (PEMFCs), membrane polymer should have a good ionic conductivity, high proton conductivity, and high mechanical strength. Lignosulfonate (LS) is a complex biopolymer which has crosslinks and sulfonate groups. SPS-LS blends with addition of SiO{sub 2} are used to increase the proton conductivity and to improve the mechanical properties and thermal stability. However, the biodegradation test of SPS-LS blends is required to determine whether the application of these membranes tomore » be applied as an environmentally friendly membrane. In this study, had been done the synthesis of SPS, biodegradability test of SPS-LS blends with variations of LS and SiO{sub 2} compositions. The biodegradation test was carried out in solid medium of Luria Bertani (LB) with an activated sludge used as a source of microorganism at incubation temperature of 37°C. Based on the results obtained indicated that SPS-LS-SiO{sub 2} blends are more decomposed by microorganism than SPS-LS blends. This result is supported by analysis of weight reduction percentage, functional groups with Fourier Transform Infrared (FTIR) Spectroscopy, and morphological surface with Scanning Electron Microscopy (SEM)« less

  10. Durability Evaluation of the Effects of Fischer-Tropsch Derived Synthetic Paraffinic Kerosene Blended up to 50% with Petroleum JP-8 on a Detroit Diesel/MTU 8V92TA Engine

    DTIC Science & Technology

    2011-12-01

    combustion is measured by the power output of the engine , the energy transferred to the coolant system, the energy transferred to the exhaust and energy...test equipment which affected the overall performance of the fuel blend engine . While JP-8/FT SPK fuel did not have a significant effect on engine ...components during this test, more testing is recommended to form a reliable conclusion on the effects of JP-8/FT-SPK blended fuel on the 8V92TA engine

  11. Nonlinear behavior of PP/PS blends with and without clay under large amplitude oscillatory shear (LAOS) flow

    NASA Astrophysics Data System (ADS)

    Salehiyan, Reza; Song, Hyeong Yong; Hyun, Kyu

    2015-05-01

    Dynamic oscillatory measurement, i.e., small amplitude oscillatory shear (SAOS) and large amplitude oscillatory shear (LAOS) test was used to investigate linear and non-linear viscoelastic properties of Polypropylene (PP)/Polystyrene (PS) blends with and without 5 wt.% clay (C20A). Fourier transform (FT-Rheology), Lissajous curves and stress decomposition methods were used to analyze non-linear responses under LAOS flow. Composition effects of blends were investigated prior to compatibilization effects. Elevated concentrations of dispersed phase (PS) increased the moduli G'(ω) from SAOS test and G*( γ 0) from LAOS test of the blends as well as strain thinning behavior. Interestingly, addition of 5 wt.% clay (C20A) boosted moduli of the blends as well as led to similar strain thinning behaviors among the PP/PS/C20A blends, except for the (90/10) PP/PS blend. The latter did not show improved rheological properties despite morphological improvements, as shown by SEM. Results from SEM and improved rheological properties of PP/PS/C20A blends revealed the compatibilization effects of clay (C20A) particles regardless of size reduction mechanisms. Third relative intensities ( I 3/1) from FT-rheology were found to be sensitive to clay (C20A) additions for the (70/30) and (30/70) PP/PS blends. Similarly, Lissajous curves could detect changes upon clay (C20A) addition, specifically at lower strain amplitudes whereupon addition of 5 wt.% clay resulted in the closed loops of Lissajous curves showing a more ellipsoidal shape due to increased elasticity in the blends. However, detection of these changes at larger strain amplitudes was more challenging. Therefore, stress decomposition (SD) method was applied for more precise characterization as it decomposes the total stress (σ) into elastic stress (σ') and viscous stress (σ″). Using SD method, elastic stress was more distorted, especially, strain hardening, while the total stress response remained almost unchanged at larger strain amplitudes.

  12. Durability Testing of Biomass Based Oxygenated Fuel Components in a Compression Ignition Engine

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ratcliff, Matthew A; McCormick, Robert L; Baumgardner, Marc E.

    Blending cellulosic biofuels with traditional petroleum-derived fuels results in transportation fuels with reduced carbon footprints. Many cellulosic fuels rely on processing methods that produce mixtures of oxygenates which must be upgraded before blending with traditional fuels. Complete oxygenate removal is energy-intensive and it is likely that such biofuel blends will necessarily contain some oxygen content to be economically viable. Previous work by our group indicated that diesel fuel blends with low levels (<4%-vol) of oxygenates resulted in minimal negative effects on short-term engine performance and emissions. However, little is known about the long-term effects of these compounds on engine durabilitymore » issues such as the impact on fuel injection, in-cylinder carbon buildup, and engine oil degradation. In this study, four of the oxygenated components previously tested were blended at 4%-vol in diesel fuel and tested with a durability protocol devised for this work consisting of 200 hrs of testing in a stationary, single-cylinder, Yanmar diesel engine operating at constant load. Oil samples, injector spray patterns, and carbon buildup from the injector and cylinder surfaces were analyzed. It was found that, at the levels tested, these fuels had minimal impact on the overall engine operation, which is consistent with our previous findings.« less

  13. Fortification of Wheat Bread with 3-7% Defatted Soy Flour Improves Formulation, Organoleptic Characteristics, and Rat Growth Rate

    PubMed Central

    Mahmoodi, Mohammad Reza; Mashayekh, Morteza; Entezari, Mohammad Hasan

    2014-01-01

    Background: The present study designed to test effects of defatted soy-fortified wheat bread on the organoleptic properties as well as influences on rat growth rate. Methods: Defatted soy flour (DSF) was blended with wheat flour with extraction rate of 82-84% at 3, 7, and 7% levels plus 3% sugar. Bread produced with these blends compared with regular Taftoon bread and was tested for chemical and organoleptic characteristics. The organoleptic characteristics of blends consist of taste and flavor, crust texture, fragrance and aroma, appearance, bendability, and overall acceptability were determined through taste panel by 213 judges. Forty Sprague Dawley rats were randomly given codes and allocated to different groups via tables with random numbers to feed on three DSF-fortified bread blends and control bread for 30 days. Results: The blending of wheat flour with DSF altered the organoleptic properties of breads. Addition of DSF increased significantly the protein and ash content of the bread (P < 0.05). Organoleptic test indicates that the best formulation is between 3 and 7% fortifications of DSF blends. In biological evaluation, rats fed the control diet had the lowest body weight gain and their food efficiency ratio was significantly different (P < 0.05) in compare with 7% DSF-fortified blend. Conclusions: It was concluded that overall acceptability score significantly decreased with increasing DSF substitution level. Rats fed 7% DSF-fortified blend showed privileged food efficiency ratio. Then, the best formulation is between 3 and 7% DSF bread. This formulation can nourish all human at risk of malnutrition. PMID:24554990

  14. Thermal lens spectroscopy for the differentiation of biodiesel-diesel blends

    NASA Astrophysics Data System (ADS)

    Ventura, M.; Simionatto, E.; Andrade, L. H. C.; Lima, S. M.

    2012-04-01

    Thermal lens (TL) spectroscopy was applied to biofuels to test its potential to distinguish diesel from biodiesel in blended fuels. Both the heat and mass diffusion effects observed using a TL procedure provide significant information about biodiesel concentrations in blended fuels. The results indicate that the mass diffusivity decreases 32% between diesel and the blend with 10% biodiesel added to the diesel. This simple TL procedure has the potential to be used for in loco analyses to certify the mixture and quality of biodiesel-diesel blends.

  15. Mechanical properties of HDPE/UHMWPE blends: effect of filler loading and filler treatment.

    PubMed

    Lai, K L K; Roziyanna, A; Ogunniyi, D S; Zainal, Arifin M I; Azlan, Ariffin A

    2004-05-01

    Various blend ratios of high-density polyethylene (HDPE) and ultra high molecular weight polyethylene (UHMWPE) were prepared with the objective of determining their suitability as biomaterials. In the unfilled state, a blend of 50/50 (HDPE/UHMWPE) ratio by weight was found to yield optimum properties in terms of processability and mechanical properties. Hydroxyapatite (HA) was compounded with the optimum blend ratio. The effects of HA loading, varied from 0 to 50wt% for both filled and unfilled blends were tested for mechanical properties. It was found that the inclusion of HA in the blend led to a remarkable improvement of mechanical properties compared to the unfilled blend. In order to improve the bonding between the polymer blend and the filler, the HA used was chemically treated with a coupling agent known as 3-(trimethoxysiyl) propyl methacrylate and the treated HA was mixed into the blend. The effect of mixing the blend with silane-treated HA also led to an overall improvement of mechanical properties.

  16. 40 CFR 80.340 - What standards and requirements apply to refiners producing gasoline by blending blendstocks into...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... to refiners producing gasoline by blending blendstocks into previously certified gasoline (PCG)? 80... (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Sampling, Testing and Retention... gasoline by blending blendstocks into previously certified gasoline (PCG)? (a) Any refiner who produces...

  17. 40 CFR 80.340 - What standards and requirements apply to refiners producing gasoline by blending blendstocks into...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... to refiners producing gasoline by blending blendstocks into previously certified gasoline (PCG)? 80... (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Sampling, Testing and Retention... gasoline by blending blendstocks into previously certified gasoline (PCG)? (a) Any refiner who produces...

  18. 40 CFR 80.340 - What standards and requirements apply to refiners producing gasoline by blending blendstocks into...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... to refiners producing gasoline by blending blendstocks into previously certified gasoline (PCG)? 80... (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Sampling, Testing and Retention... gasoline by blending blendstocks into previously certified gasoline (PCG)? (a) Any refiner who produces...

  19. 40 CFR 80.340 - What standards and requirements apply to refiners producing gasoline by blending blendstocks into...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... to refiners producing gasoline by blending blendstocks into previously certified gasoline (PCG)? 80... (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Sampling, Testing and Retention... gasoline by blending blendstocks into previously certified gasoline (PCG)? (a) Any refiner who produces...

  20. 40 CFR 80.340 - What standards and requirements apply to refiners producing gasoline by blending blendstocks into...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... to refiners producing gasoline by blending blendstocks into previously certified gasoline (PCG)? 80... (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Sampling, Testing and Retention... gasoline by blending blendstocks into previously certified gasoline (PCG)? (a) Any refiner who produces...

  1. 40 CFR 1065.1010 - Incorporation by reference.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... approved for § 1065.701(f). (43) ASTM D6751-12, Standard Specification for Biodiesel Fuel Blend Stock (B100... D7039-13, Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence...

  2. Development of on-board fuel metering and sensing system

    NASA Astrophysics Data System (ADS)

    Hemanth, Y.; Manikanta, B. S. S.; Thangaraja, J.; Bharanidaran, R.

    2017-11-01

    Usage of biodiesel fuels and their blends with diesel fuel has a potential to reduce the tailpipe emissions and reduce the dependence on crude oil imports. Further, biodiesel fuels exhibit favourable greenhouse gas emission and energy balance characteristics. While fossil fuel technology is well established, the technological implications of biofuels particularly biodiesel is not clearly laid out. Hence, the objective is to provide an on-board metering control in selecting the different proportions of diesel and bio-diesel blends. An on-board fuel metering system is being developed using PID controller, stepper motors and a capacitance sensor. The accuracy was tested with the blends of propanol-1, diesel and are found to be within 1.3% error. The developed unit was tested in a twin cylinder diesel engine with biodiesel blended diesel fuel. There was a marginal increase (5%) in nitric oxide and 14% increase in smoke emission with 10% biodiesel blended diesel at part load conditions.

  3. Modeling and testing of fractionation effects with refrigerant blends in an actual residential heat pump system

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Biancardi, F.R.; Pandy, D.R.; Sienel, T.H.

    1997-12-31

    The heating, ventilating, and air-conditioning (HVAC) industry is actively evaluating and testing hydrofluorocarbon (HFC) refrigerant blends as a means of complying with current and impending national and international environmental regulations restricting the use and disposal of conventional chlorofluorocarbon (CFC) and hydrochlorofluorocarbon (HCFC) refrigerants that contribute to the global ozone-depletion effects. While analyses and system performance tools have shown that HFC refrigerant blends offer certain performance, capacity, and operational advantages, there are significant possible service and operational issues that are raised by the use of blends. Many of these issues occur due to the fractionation of the blends. Therefore, the objectivemore » of this program was to conduct analyses and experimental tests aimed at understanding these issues, develop approaches or techniques to predict these effects, and convey to the industry safe and reliable approaches. As a result, analytical models verified by laboratory data have been developed that predict the fractionation effects of HFC refrigerant blends (1) when exposed to selected POE lubricants, (2) during the system charging process from large liquid containers, and (3) during system start-up, operation, and shutdown within various system components (where two-phase refrigerant exists) and during selected system and component leakage scenarios. Model predictions and experimental results are presented for HFC refrigerant blends containing R-32, R-134a, and R-125 and the data are generalized for various operating conditions and scenarios.« less

  4. Flight Investigation of the Knock-Limited Performance of a Triptane Blend, a Toluene Blend, and 28-R Fuel in an R-1830-75 Engine

    NASA Technical Reports Server (NTRS)

    Blackman, Calvin C.

    1946-01-01

    Knock-limited performance data were obtained for three fuels on an R-1830-75 engine in a B-24D airplane at engine speeds of 1800, 2250, and 2600 rpm, a spark advance of 25 degrees B.T.C., and carburetor-air temperatures of 85 F for 1800 and 2250 rpm and 100 F for 2600 rpm. The test fuels were a blend of 80 percent 28-R plus 20 percent triptane (leaded to 4.5 ml TEL/gal), a blend of 80 percent 28-R plus 15 percent toluene (leaded to 4.5 ml TEL / gal), and 28-R fuel. The knock-limited manifold pressure of the toluene blend depreciated more in the lean region than the triptane blend or 28-R fuel. The knock-limited brake horsepower for the triptane blend varied from 16 to 25 percent higher than 28-R in the lean region and 18 to 30 percent higher in the rich region. The knock-limited brake horsepower of the toluene blend was approximately 15 percent higher than that of 28-R in the rich region and varied from 2 to 10 percent higher in the lean region. Knock limits of the triptane blend and 28-R fuel tested in the R-1830-75 engine agreed with limits for the same fuels determined with the R-1830-94 engine for engine speeds of 1800 and 2250 rpm.

  5. Tensile properties of polyhydroxyalkanoate/polycaprolactone blends studied by rheo-optical near-infrared (NIR) spectroscopy

    NASA Astrophysics Data System (ADS)

    Nishida, Masahiro; Ogura, Takashi; Shinzawa, Hideyuki; Nishida, Masakazu; Kanematsu, Wataru

    2016-11-01

    In order to improve the mechanical properties of Polyhydroxyalkanoate (PHA), the polycaprolactone (PCL) pellet was blended with a PHA-based pellet. The effects of the mixing ratio on the tensile properties, Young's modulus, tensile strength and elongation at break, were examined using a universal testing machine. When the mixing ration of PCL increased to 50%, the elongation at break of the polymer blend increased and the gauge area of tensile test specimens whitened and became porous. In order to understand this behavior, a rheo-optical characterization technique based on near-infrared (NIR) spectroscopy was applied to the mechanical deformation of the polymer blends during static tensile tests. Two-dimensional (2D) correlation of NIR spectra was then examined. It was found from peaks of ethyl group or methyl group that PCL was preferentially deformed. The difference in the deformation behavior is thought to be the cause of the porous structure.

  6. Tibiofemoral contact stress and stress distribution evaluation of total knee arthroplasties.

    PubMed

    Szivek, J A; Cutignola, L; Volz, R G

    1995-08-01

    The Fuji film (Itochu, Los Angeles, CA) area analysis technique demonstrates that a more accurate assessment of tibiofemoral contact stresses is possible when the film is used at 37 degrees C and at the upper end of its sensitivity range (in this case, a 2,000-N load). An AMK with a regular and Hylamer-M insert (DePuy, Warsaw, IN), an MG II (Zimmer, Warsaw, IN), an Omnifit (Osteonics, Allendale, NJ), an Ortholoc III (Dow Corning Wright, Midland, MI), a PCA II (Howmedica, Rutherford, NJ), and a PFC (Johnson & Johnson Orthopaedics, Raynham, MA) had average contact stresses that varied only 12% at 60 degrees flexion. At 0 degrees, 15 degrees and 60 degrees flexion, stresses ranged from 13 to 25 MPa. Contact area distribution ratios, which were smaller at 37 degrees C than at 24 degrees C, provide a quantitative means of grouping implants according to the shape of the tibiofemoral contact area. The Omnifit, MG II, PCA II, and PFC had small ratios (symmetric areas). The AMK and Ortholoc III had large ratios (asymmetric contact areas). If the impression is reflective of wear, it would be expected to be focal in knees with small ratios and contact areas, and uniform in knees with large ratios and contact areas, whereas large ratios and small areas would imply a linear wear pattern. Calibrated electrical resistance contact stress measurements indicated that the Fuji film measurements underestimated the magnitude of contact stresses. They also provided a means of quantifying the rate of area increase during initial loading of the knees, with the highest area increase noted for the knee with the roughest insert (Ortholoc III) and the lowest area increase for the knee with the smoothest insert (PCA II).

  7. Enhancing the Dyeability of Polypropylene Fibers by Melt Blending with Polyethylene Terephthalate

    PubMed Central

    Moradian, Siamak; Ameri, Farhad

    2013-01-01

    Attempts were made to modify polypropylene fibers by melt blending with polyethylene terephthalate in order to enhance the dyeability of the resultant fiber. Five blends of polypropylene/polyethylene terephthalate/compatibilizer were prepared and subsequently spun into fibers. Three disperse dyes were used to dye such modified fibers at boiling and 130°C. The dyeing performance of the blend fibers, as well as the morphological, chemical, thermal, and mechanical properties, of the corresponding blends was characterized by means of spectrophotometry, polarized optical microscopy, scanning electron microscopy (SEM), FT-IR spectroscopy, differential scanning calorimetry (DSC), and tensile testing. PMID:24288485

  8. Thermal, mechanical and morphological characterization of plasticized PLA-PHB blends

    USDA-ARS?s Scientific Manuscript database

    A blend of poly(lactic acid) (PLA) (75% by weight) and poly(3-hydroxybutyrate) (PHB) (25% by weight) with a polyester plasticizer (Lapol 108) at two different concentrations (5 and 7% by weight per 100 parts of the blends) were investigated by TGA, DSC, XRD, SEM, mechanical testing and biodegradatio...

  9. Enhancing Student Teachers' Teaching Skills through a Blended Learning Approach

    ERIC Educational Resources Information Center

    Albhnsawy, Abeer Abdalhalim; Aliweh, Ahmed Mahmoud

    2016-01-01

    This study investigated the effect of a blended learning program on student teachers' teaching skills in an undergraduate microteaching course. The blended learning program lasted for nine weeks. This program aimed at integrating social network tasks and face-to-face teaching activities. Pre- and post-tests were administered to assess student…

  10. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Laguna, O.; Collar, E.P.; Taranco, J.

    Observations are made about microstructural aspects from HDPE and LDPE homopolymers and their blends as virgin materials and also from urban plastic wastes. Micrographs were taken by SEM. Micrographs corresponding to the fracture surface from specimens tested in an impact test clearly show different microstructural features due to polymer which is more than 50%. Parts were injection molded. A discussion is given about crystallization behavior of those materials obtained by DSC. For all blends the same results have been found, i.e., two peaks owing to each of the two polymers which are present in the blends.

  11. Effects of Blended Instructional Models on Math Performance

    ERIC Educational Resources Information Center

    Bottge, Brian A.; Ma, Xin; Gassaway, Linda; Toland, Michael D.; Butler, Mark; Cho, Sun-Joo

    2014-01-01

    A pretest-posttest cluster-randomized trial involving 31 middle schools and 335 students with disabilities tested the effects of combining explicit and anchored instruction on fraction computation and problem solving. Results of standardized and researcher-developed tests showed that students who were taught with the blended units outscored…

  12. The Development of a Survey Instrument to Measure Transactional Distance in Secondary Blended Learning Environments

    ERIC Educational Resources Information Center

    Lane, Dennis Glenn

    2017-01-01

    The goal of this study was to develop a survey instrument to measure transactional distance in secondary blended learning environments. This study resulted in a 35-item survey instrument, the Blended Learning Assessment Scale of Transactional Distance (BLASTD), which was tested using a convenience sample of secondary students (n = 222) at a…

  13. Blended E-Learning as a Requirement for Teaching EFL in a Thai Academic Context

    ERIC Educational Resources Information Center

    Tananuraksakul, Noparat

    2016-01-01

    This paper results from a pilot study in a Thai academic context testing two hypotheses. First, blended e-learning required by an institution can motivate learners extrinsically to learn EFL. Second, blended e-learning can enhance learners' positive attitudes toward learning EFL. The hypotheses were constructed based on an implication that Thai…

  14. Blended Learning vs. Traditional Instruction as a Predictor of Student Achievement in New York City Public Schools

    ERIC Educational Resources Information Center

    Murray, Anthony

    2017-01-01

    This study explored the differences in student achievement on New York State standardized tests between blended learning and traditional instructional methodologies. Specifically, the study compared student achievement in iLearnNYC schools, to their peer schools that deliver instruction in a traditional manner. iLearnNYC is a blended learning…

  15. Effect of lower and higher alcohol fuel synergies in biofuel blends and exhaust treatment system on emissions from CI engine.

    PubMed

    Subramanian, Thiyagarajan; Varuvel, Edwin Geo; Martin, Leenus Jesu; Beddhannan, Nagalingam

    2017-11-01

    The present study deals with performance, emission and combustion studies in a single cylinder CI engine with lower and higher alcohol fuel synergies with biofuel blends and exhaust treatment system. Karanja oil methyl ester (KOME), widely available biofuel in India, and orange oil (ORG), a low carbon biofuel, were taken for this study, and equal volume blend was prepared for testing. Methanol (M) and n-pentanol (P) was taken as lower and higher alcohol and blended 20% by volume with KOME-ORG blend. Activated carbon-based exhaust treatment indigenous system was designed and tested with KOME-ORG + M20 and KOME-ORG + P20 blend. The tests were carried out at various load conditions at a constant speed of 1500 rpm. The study revealed that considering performance, emission and combustion studies, KOME-ORG + M20 + activated carbon are found optimum in reducing NO, smoke and CO 2 emission. Compared to KOME, for KOME-ORG + M20 + activated carbon, NO emission is reduced from 10.25 to 7.85 g/kWh, the smoke emission is reduced from 49.4 to 28.9%, and CO 2 emission is reduced from 1098.84 to 580.68 g/kWh. However, with exhaust treatment system, an increase in HC and CO emissions and reduced thermal efficiency is observed due to backpressure effects.

  16. Experimental Investigation of Performance and emission characteristics of Various Nano Particles with Bio-Diesel blend on Di Diesel Engine

    NASA Astrophysics Data System (ADS)

    Karthik, N.; Goldwin Xavier, X.; Rajasekar, R.; Ganesh Bairavan, P.; Dhanseelan, S.

    2017-05-01

    Present study provides the effect of Zinc Oxide (ZnO) and Cerium Oxide (CeO2) nanoparticles additives on the Performance and emission uniqueness of Jatropha. Jatropha blended fuel is prepared by the emulsification technique with assist of mechanical agitator. Nano particles (Zinc Oxide (ZnO)) and Cerium Oxide (CeO2)) mixed with Jatropha blended fuel in mass fraction (100 ppm) with assist of an ultrasonicator. Experiments were conducted in single cylinder constant speed direct injection diesel engine for various test fuels. Performance results revealed that Brake Thermal Efficiency (BTE) of Jatropha blended Cerium Oxide (B20CE) is 3% and 11% higher than Jatropha blended zinc oxide (B20ZO) and Jatropha blended fuel (B20) and 4% lower than diesel fuel (D100) at full load conditions. Emission result shows that HC and CO emissions of Jatropha blended Cerium Oxide (B20CE) are (6%, 22%, 11% and 6%, 15%, 12%) less compared with Jatropha blended Zinc Oxide (B20ZO), diesel (D100) and Jatropha blended fuel (B20) at full load conditions. NOx emissions of Jatropha blended Cerium Oxide is 1 % higher than diesel fuel (D100) and 2% and 5% lower than Jatropha blended Zinc Oxide, and jatropha blended fuel.

  17. Comparative study of performance and emissions of a CI engine using biodiesel of microalgae, macroalgae and rice bran

    NASA Astrophysics Data System (ADS)

    Jayaprabakar, J.; Karthikeyan, A.; Saikiran, K.; Beemkumar, N.; Joy, Nivin

    2017-05-01

    Biodiesel is an alternative and safe fuel to replace conventional petroleum diesel. With high-lubricity and clean-burning ability the biodiesel can be a better fuel component for use in existing diesel engines without any modifications. The aim of this Research was to study the potential use of Macro algae oil, Micro algae oil, Rice Bran oil methyl ester as a substitute for diesel fuel in diesel engine. B10 and B20 blends of these three types of fuels are prepared by transesterification process. The blends on volume basis were used to test them in a four stroke single cylinder diesel engine to study the performance and emission characteristics of these fuels and compared with neat diesel fuel. Also, the property testing of these biofuels were carried out. The biodiesel blends in this study substantially reduces the emission of unburnt hydro carbons and smoke opacity and increases the emission of NOx emission in exhaust gases. These biodiesel blends were consumed more by the engine during testing than Diesel and the brake thermal efficiency and volumetric efficiency for the blends was identical with the Diesel.

  18. Poly(hydroxybutyrate)/cellulose acetate blend nanofiber scaffolds: Preparation, characterization and cytocompatibility.

    PubMed

    Zhijiang, Cai; Yi, Xu; Haizheng, Yang; Jia, Jianru; Liu, Yuanpei

    2016-01-01

    Poly(hydroxybutyrate) (PHB)/cellulose acetate (CA) blend nanofiber scaffolds were fabricated by electrospinning using the blends of chloroform and DMF as solvent. The blend nanofiber scaffolds were characterized by SEM, FTIR, XRD, DSC, contact angle and tensile test. The blend nanofibers exhibited cylindrical, uniform, bead-free and random orientation with the diameter ranged from 80-680 nm. The scaffolds had very well interconnected porous fibrous network structure and large aspect surface areas. It was found that the presence of CA affected the crystallization of PHB due to formation of intermolecular hydrogen bonds, which restricted the preferential orientation of PHB molecules. The DSC result showed that the PHB and CA were miscible in the blend nanofiber. An increase in the glass transition temperature was observed with increasing CA content. Additionally, the mechanical properties of blend nanofiber scaffolds were largely influenced by the weight ratio of PHB/CA. The tensile strength, yield strength and elongation at break of the blend nanofiber scaffolds increased from 3.3 ± 0.35 MPa, 2.8 ± 0.26 MPa, and 8 ± 0.77% to 5.05 ± 0.52 MPa, 4.6 ± 0.82 MPa, and 17.6 ± 1.24% by increasing PHB content from 60% to 90%, respectively. The water contact angle of blend nanofiber scaffolds decreased about 50% from 112 ± 2.1° to 60 ± 0.75°. The biodegradability was evaluated by in vitro degradation test and the results revealed that the blend nanofiber scaffolds showed much higher degradation rates than the neat PHB. The cytocompatibility of the blend nanofiber scaffolds was preliminarily evaluated by cell adhesion studies. The cells incubated with PHB/CA blend nanofiber scaffold for 48 h were capable of forming cell adhesion and proliferation. It showed much better biocompatibility than pure PHB film. Thus, the prepared PHB/CA blend nanofiber scaffolds are bioactive and may be more suitable for cell proliferation suggesting that these scaffolds can be used for wound dressing or tissue-engineering scaffolds. Copyright © 2015 Elsevier B.V. All rights reserved.

  19. Mechanical characterization and modelling of the temperature-dependent impact behaviour of a biocompatible poly(L-lactide)/poly(ε-caprolactone) polymer blend.

    PubMed

    Gustafsson, Gustaf; Nishida, Masahiro; Ito, Yoshitaka; Häggblad, Hans-Åke; Jonsén, Pär; Takayama, Tetsuo; Todo, Mitsugu

    2015-11-01

    Poly(ε-caprolactone) (PCL) is a ductile, bioabsorbable polymer that has been employed as a blend partner for poly(L-lactic acid) (PLLA). An improvement of the material strength and impact resistance of PLLA/PCL polymer blends compared to pure PLLA has been shown previously. To use numerical simulations in the design process of new components composed of the PLLA/PCL blend, a constitutive model for the material has to be established. In this work, a constitutive model for a PLLA/PCL polymer blend is established from the results of compressive tests at high and low strain rates at three different temperatures, including the body temperature. Finite element simulations of the split Hopkinson pressure bar test using the established constitutive model are carried out under the same condition as the experiments. During the experiments, the changes in the diameter and thickness of the specimens are captured by a high-speed video camera. The accuracy of the numerical model is tested by comparing the simulation results, such as the stress, strain, thickness and diameter histories of the specimens, with those measured in the experiments. The numerical model is also validated against an impact test of non-homogenous strains and strain rates. The results of this study provide a validated numerical model for a PLLA/PCL polymer blend at strain rates of up to 1800 s(-1) in the temperature range between 22°C and 50°C. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Mechanical properties of PA6/PP compatibilized nanocomposites using a twin screw extruder

    NASA Astrophysics Data System (ADS)

    De Almeida, M. F.; Correia, Aldina; e Silva, Eliana Costa; Lopes, I. Cristina

    2017-11-01

    In this article, a new approach to study the compatibilization effect of organophilic clays in PA6/PP polymer blends through experimental results of mechanical tests is presented. This study focus on the description of the interphase in compatibilization by addition of the organoclays C15A and C30B into the polymer PA6/PP blend by melt compounding using a Twin Screw Extruder. The experimental results variations are studied, by addition of the organoclays in uncompatibilized polymer blend, using non-parametric analysis of variance (Kruskal-Wallis Test). For all the experimental results, significant differences are identified between the types of polymer blends. It was observed the compatibilization effect of both organophilic clays, being the differences most evident in the presence of PP modified.

  1. Assessing the impacts of ethanol and isobutanol on gaseous and particulate emissions from flexible fuel vehicles.

    PubMed

    Karavalakis, Georgios; Short, Daniel; Russell, Robert L; Jung, Heejung; Johnson, Kent C; Asa-Awuku, Akua; Durbin, Thomas D

    2014-12-02

    This study investigated the effects of higher ethanol blends and an isobutanol blend on the criteria emissions, fuel economy, gaseous toxic pollutants, and particulate emissions from two flexible-fuel vehicles equipped with spark ignition engines, with one wall-guided direct injection and one port fuel injection configuration. Both vehicles were tested over triplicate Federal Test Procedure (FTP) and Unified Cycles (UC) using a chassis dynamometer. Emissions of nonmethane hydrocarbons (NMHC) and carbon monoxide (CO) showed some statistically significant reductions with higher alcohol fuels, while total hydrocarbons (THC) and nitrogen oxides (NOx) did not show strong fuel effects. Acetaldehyde emissions exhibited sharp increases with higher ethanol blends for both vehicles, whereas butyraldehyde emissions showed higher emissions for the butanol blend relative to the ethanol blends at a statistically significant level. Particulate matter (PM) mass, number, and soot mass emissions showed strong reductions with increasing alcohol content in gasoline. Particulate emissions were found to be clearly influenced by certain fuel parameters including oxygen content, hydrogen content, and aromatics content.

  2. Preparation and characterization of poly(acrylic acid)—corn starch blend for use as chemical sand-fixing materials

    NASA Astrophysics Data System (ADS)

    Dang, Xugang; Chen, Hui; Shan, Zhihua

    2017-07-01

    One chemical sand-fixing materials based on poly(acrylic acid)-corn starch (PACS) blend was studied in this work. The PACS blend was prepared by solution mixing method between PA and CS. In order to prepare sand-fixing materials for environmental applications using the well-established method of spraying evenly PACS blend solution on the surfaces of fine sand. Fourier transform infrared spectroscopy (FT-IR) revealed the existence of the intermolecular interactions between the blend components. Scanning electron microscope (SEM) analysis showed a continuous phase of blend, and it also showed the good sand-fixing capacity. The test results of hygroscopicity and water retention experiments indicated that the blends had excellent water-absorbing and water-retention capacity. The results of contact angle measurements between the PACS solutions and fine sand showed that the PACS blend has a satisfactory effect on fine sand wetting. And the PACS, as a sand-fixation material, has excellent sand-fixation rate up to 99.5%.

  3. A robust quantitative near infrared modeling approach for blend monitoring.

    PubMed

    Mohan, Shikhar; Momose, Wataru; Katz, Jeffrey M; Hossain, Md Nayeem; Velez, Natasha; Drennen, James K; Anderson, Carl A

    2018-01-30

    This study demonstrates a material sparing Near-Infrared modeling approach for powder blend monitoring. In this new approach, gram scale powder mixtures are subjected to compression loads to simulate the effect of scale using an Instron universal testing system. Models prepared by the new method development approach (small-scale method) and by a traditional method development (blender-scale method) were compared by simultaneously monitoring a 1kg batch size blend run. Both models demonstrated similar model performance. The small-scale method strategy significantly reduces the total resources expended to develop Near-Infrared calibration models for on-line blend monitoring. Further, this development approach does not require the actual equipment (i.e., blender) to which the method will be applied, only a similar optical interface. Thus, a robust on-line blend monitoring method can be fully developed before any large-scale blending experiment is viable, allowing the blend method to be used during scale-up and blend development trials. Copyright © 2017. Published by Elsevier B.V.

  4. Emissions characteristics of a diesel engine operating on biodiesel and biodiesel blended with ethanol and methanol.

    PubMed

    Zhu, Lei; Cheung, C S; Zhang, W G; Huang, Zhen

    2010-01-15

    Euro V diesel fuel, pure biodiesel and biodiesel blended with 5%, 10% and 15% of ethanol or methanol were tested on a 4-cylinder naturally-aspirated direct-injection diesel engine. Experiments were conducted under five engine loads at a steady speed of 1800 r/min. The study aims to investigate the effects of the blended fuels on reducing NO(x) and particulate. On the whole, compared with Euro V diesel fuel, the blended fuels could lead to reduction of both NO(x) and PM of a diesel engine, with the biodiesel-methanol blends being more effective than the biodiesel-ethanol blends. The effectiveness of NO(x) and particulate reductions is more effective with increase of alcohol in the blends. With high percentage of alcohol in the blends, the HC, CO emissions could increase and the brake thermal efficiency might be slightly reduced but the use of 5% blends could reduce the HC and CO emissions as well. With the diesel oxidation catalyst (DOC), the HC, CO and particulate emissions can be further reduced. Copyright 2009 Elsevier B.V. All rights reserved.

  5. Experimental investigation on CRDI engine using butanol-biodiesel-diesel blends as fuel

    NASA Astrophysics Data System (ADS)

    Divakar Shetty, A. S.; Dineshkumar, L.; Koundinya, Sandeep; Mane, Swetha K.

    2017-07-01

    In this research work an experimental investigation of butanol-biodisel-diesel blends on combustion, performance and emission characteristics of a direct injection (DI) diesel engine is carried out. The blends are prepared at different proportions and fuel properties such as calorific value, viscosity, flash point and fire point, cloud point, pour point of butanol (B), biodiesel (B), diesel (D), biodiesel-diesel (BD) blends and butanol-biodiesel-diesel (BBD) blends are determined. The engine test is conducted at different speed and load. From the results obtained for fuel properties we can observe that the flash, fire and pour point, viscosity and density are decreasing by increasing the percentage of butanol in BBD blends. It is also observed that the performance parameters such as brake thermal efficiency (BTE) and exhaust gas temperature increases with increase in the proportion of butanol in BBD blend. However, the brake specific fuel consumption (BFSC) decreases with increase in the proportion of butanol in BBD blend. The increase of butanol in BBD blends also influence to increase on emission characteristic such as carbon monoxide (CO), hydrocarbon (HC) and oxides of nitrogen (NOx).

  6. U.S. Department of Energy FreedomCAR & Vehicle Technologies Program Advanced Vehicle Testing Activity, Hydrogen/CNG Blended Fuels Performance Testing in a Ford F-150

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    James E. Francfort

    2003-11-01

    Federal regulation requires energy companies and government entities to utilize alternative fuels in their vehicle fleets. To meet this need, several automobile manufacturers are producing compressed natural gas (CNG)-fueled vehicles. In addition, several converters are modifying gasoline-fueled vehicles to operate on both gasoline and CNG (Bifuel). Because of the availability of CNG vehicles, many energy company and government fleets have adopted CNG as their principle alternative fuel for transportation. Meanwhile, recent research has shown that blending hydrogen with CNG (HCNG) can reduce emissions from CNG vehicles. However, blending hydrogen with CNG (and performing no other vehicle modifications) reduces engine powermore » output, due to the lower volumetric energy density of hydrogen in relation to CNG. Arizona Public Service (APS) and the U.S. Department of Energy’s Advanced Vehicle Testing Activity (DOE AVTA) identified the need to determine the magnitude of these effects and their impact on the viability of using HCNG in existing CNG vehicles. To quantify the effects of using various blended fuels, a work plan was designed to test the acceleration, range, and exhaust emissions of a Ford F-150 pickup truck operating on 100% CNG and blends of 15 and 30% HCNG. This report presents the results of this testing conducted during May and June 2003 by Electric Transportation Applications (Task 4.10, DOE AVTA Cooperative Agreement DEFC36- 00ID-13859).« less

  7. Reading Achievement and Reading Efficacy Changes for Middle School Students with Disabilities through Blended Learning Instruction

    ERIC Educational Resources Information Center

    Pace, Jesse R.; Mellard, Daryl F.

    2016-01-01

    This study evaluated the effects of a blended learning instructional experience for sixth-grade students in an English/language arts (ELA) course. Students at two treatment schools participated in a blended learning instructional paradigm, and their ELA test scores were compared to one comparison school that used a face-to-face delivery. Other…

  8. Biodegradable blends of poly (lactic acid) (PLA) / polyhydroxybutrate (PHB) copolymer and its effects on rheological, thermal and mechanical properties

    NASA Astrophysics Data System (ADS)

    Sood, Nitin K.

    Poly (Lactic acid) is the most important plastic derived from the renewable resources. PLA based products have extensively been used in the medical industry. However, PLA has a few disadvantages such as inherent brittleness and low toughness despite a high modulus. A focus of this experiment was to study the improvement in toughness of PLA and to study the changes in thermal and rheological properties by blending PLA with a PHB copolymer. Where, PLA and PHB copolymer were melt blended using a twin screw Brabender extruder in the ratios of 100/0, 70/30, 50/50, 30/70, 0/100. Further, the blends were injection molded into tensile bar and impact bars for mechanical testing. Rheological properties were studied using a Galaxy capillary rheometer for melt viscosities and temperature dependence indicated a shear-thinning behavior along with power law model and consistency index. Blends were characterized to study the phase model using a differential scanning calorimetric (DSC), showed two separate phases. Mechanical properties were analyzed using a Tensile and Izod impact test indicating decrease in elastic modulus with increase in toughness and elongation as the PHB copolymer content was increased in the blend.

  9. Quality-by-design (QbD): effects of testing parameters and formulation variables on the segregation tendency of pharmaceutical powder measured by the ASTM D 6940-04 segregation tester.

    PubMed

    Xie, Lin; Wu, Huiquan; Shen, Meiyu; Augsburger, Larry L; Lyon, Robbe C; Khan, Mansoor A; Hussain, Ajaz S; Hoag, Stephen W

    2008-10-01

    The objective of this study was to examine the effects of testing parameters and formulation variables on the segregation tendency of pharmaceutical powders measured by the ASTM D 6940-04 segregation tester using design of experiments (DOE) approaches. The test blends consisted of 4% aspirin (ASP) and 96% microcrystalline cellulose (MCC) with and without magnesium stearate (MgS). The segregation tendency of a blend was determined by measuring the last/first (L/F) ratio, the ratio of aspirin concentrations between the first and last samples discharged from the tester. A 2(2) factorial design was used to determine the effects of measurement parameters [amount of material loaded (W), number of segregation cycles] with number of replicates 6. ANOVA showed that W was a critical parameter for segregation testing. The L/F value deviated further from 1 (greater segregation tendency) with increasing W. A 2(3) full factorial design was used to assess the effects of formulation variables: grade of ASP (unmilled, milled), grade of MCC, and amount of lubricant, MgS. MLR and ANOVA showed that the grade of ASP was the main effect contributing to segregation tendency. Principal Component Regression Analysis established a correlation between L/F and the physical properties of the blend related to ASP and MCC, the ASP/MCC particle size ratio (PSR) and powder cohesion. The physical properties of the blend related to density and flow were not influenced by the grade of ASP and were not related to the segregation tendency of the blend. The direct relationship between L/F and PSR was determined by univariate analysis. Segregation tendency increased as the ASP to MCC particle size increased. This study highlighted critical test parameters for segregation testing and identified critical physical properties of the blends that influence segregation tendency. (c) 2008 Wiley-Liss, Inc. and the American Pharmacists Association

  10. Production and characterization of novel starch and poly(butylene adipate-co-terephthalate)-based materials and their applications

    NASA Astrophysics Data System (ADS)

    Stagner, Jacqueline Ann

    This work focuses on the production and characterization of blends of maleated thermoplastic starch (MTPS) and poly(butylenes adipate-co-terephthalate) and their application for use as thermoformed objects, films, and foams. First, by the production and characterization of maleated thermoplastic starch (MTPS) synthesized by reactive extrusion in a twin-screw extruder, a better understanding of MTPS was gained. This reactive thermoplastic starch was prepared with glycerol as the plasticizer, maleic anhydride (MA), and free-radical initiator, 2,5-bis(tert-butylperoxy)-2,5-dimethylhexane (Luperox 101). Dynamic light scattering (DLS), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), soxhlet extraction in acetone, and environmental scanning electron microscopy (ESEM) were performed to determine the effect of maleation, extrusion temperature, initiator concentration, and maleic anhydride concentration on the resulting MTPS. Next, maleated thermoplastic starch (MTPS) and thermoplastic starch (TPS) were reactively blended in a twin-screw extruder with a biodegradable polyester, poly(butylene adipate-co-terephthalate) (PBAT). The blends were extruded to produce thermoformable sheets. The mechanical properties of the sheets were characterized by tensile and puncture tests. Proof of grafting was determined by soxhlet extraction in dichloromethane and FTIR analysis. Observations of the thermal properties were made using DSC, while the surface of the sheets was imaged using ESEM. Blends of MTPS and PBAT were also extruded to produce films. Mechanical testing (tensile and puncture tests) and barrier performance testing (carbon dioxide, oxygen, and water vapor permeability) were performed on the films. Transmission electron microscopy (TEM) was used to image the blends and to view the dispersion of the various phases. Finally, blends of MTPS and PBAT were extruded with an endothermic chemical blowing agent to produce foams. The foams were characterized by measuring density, expansion ratio, specific length, compressive strength, resiliency, and moisture sorption. Also, digital light microscopy was used to image the cell structure of the foams. This work demonstrates that blends of starch and PBAT can be produced and formed into thermoformed objects, films, and foams. These objects can replace current objects made from non-biodegradable, petroleum-based plastics. By blending the starch and PBAT together, one receives advantages over using either component separately.

  11. Green fuel utilization for diesel engine, combustion and emission analysis fuelled with CNSO diesel blends with Diethyl ether as additive

    NASA Astrophysics Data System (ADS)

    Kumar, Ashok; Rajan, K.; Senthil Kumar, K. R.; Maiyappan, K.; Rasheed, Usama Tariq

    2017-05-01

    The experimental investigation is conducted to evaluate the effects by using Diethyl ether (DEE) as an additive. The Cashew Nut Shell Oil diesel blends (CDB) are tested in a 4-stroke single cylinder DI unmodified diesel engine, rated power is 4.4 kW at a speed of 1500 rpm. The effect of combustion analysis of test fuels on net heat release rate, cylinder pressure, engine power, BSFC, BTE, EGT were observed by the performance tests. The combustion and emission characteristics of a diesel engine with an additive of high cetane number is utilized with CDB and thus investigated. The influence of blends on CO, CO2, HC, NOx and smoke opacity is investigated by emission tests. Initially, the experiment was conducted with different blends of CDB diesel blends like 10%, 20%, & 30% by volume basis in a diesel engine. Among this blends B20 shows reasonable result and heat dissipation rate at full load conditions. The BTE of B20 is 27.52% whereas base diesel fuel is 29.73%. Addition of the DEE by 5%, 10% and 15% by volume basis with B20 which is a base fuel has resulted with improved estimates. The result shows that at full load conditions BTE of B20D10 is 28.96% which is close to the base fuel i.e. B20. The emissions like CO2 shows reducing trends while HC emission rises with increase in CNSO blends. The HC in diesel corresponds to 30ppm and in B20 it is 34ppm, but addition of DEE shows a decreasing trend as in B20D5 has 29ppm and B20D15 has 23ppm respectively. NOx also shows increasing trends with CNSO blend, after addition of DEE it shows declining trend. The NOx for diesel, B20, B30, B20D5, B20D10 and B20D15 emits 1195, 1450, 1511, 1327, 1373 and 1200ppm respectively. The smoke emission is 3.96, 3.38, 3.15 FSN of B20, B20D15 and diesel respectively.

  12. Microbial communities responsible for the degradation of poly(lactic acid)/poly(3-hydroxybutyrate) blend mulches in soil burial respirometric tests.

    PubMed

    Jeszeová, Lenka; Puškárová, Andrea; Bučková, Mária; Kraková, Lucia; Grivalský, Tomáš; Danko, Martin; Mosnáčková, Katarína; Chmela, Štefan; Pangallo, Domenico

    2018-06-22

    The microbial communities responsible for the degradation of poly(lactic acid)/poly(3-hydroxybutyrate) (PLA/PHB) blend foils were investigated in 1 year long laboratory soil burial experiments. Different PLA/PHB foils were tested: (a) PLA/PHB original transparent foil, (b) PLA/PHB carbon black filled foil and (c) PLA/PHB black foil previously exposed for 90 days to sun light. The microbiome diversity of these three types of foil was compared with that identified from soil/perlite sample at the beginning of experiment and that developed on a cellulose mat. Culture-dependent and culture-independent (DGGE-cloning) approaches together with PLA, PHB and PLA/PHB degradation plate assays were employed. The cultivation strategy combined with degradation tests permitted the isolation and evaluation of several PLA/PHB blend degrading microorganisms such as members of the genera Bacillus, Paenibacillus, Streptomyces, Rhodococcus, Saccharothrix, Arthrobacter, Aureobasidium, Mortierella, Absidia, Actinomucor, Bjerkandera, Fusarium, Trichoderma and Penicillium. The DGGE-cloning investigation increased the information about the microbial communities occurring during bioplastic degradation detecting several bacterial and fungal taxa and some of them (members of the orders Anaerolineales, Selenomonadales, Thelephorales and of the genera Pseudogymnoascus and Pseudeurotium) were revealed here for the first time. This survey showed the microbiome colonizing PLA/PHB blend foils and permitted the isolation of several microorganisms able to degrade the tested polymeric blends.

  13. Improvement of toughness and water resistance of bioplastic based on wheat gluten using epoxidized natural rubber

    NASA Astrophysics Data System (ADS)

    Hemsri, S.; Thongpin, C.; Somkid, P.; Sae-arma, S.; Paiykaew, A.

    2015-07-01

    Novel blends based on wheat gluten (WG) and epoxidized natural rubber (ENR) were fabricated with different ENR contents of 10, 20 and 30 wt% in an internal mixer. Sulfur vulcanization was used to crosslink the ENR phase in the blends. Comparatively, blends of WG and natural rubber (WG/NR) were prepared in the same condition as the WG/ENR blends. Tensile mechanical properties and impact strength of the WG/ENR blends were investigated and compared with the WG/NR blends as well as pure WG. Moreover, water absorption of pure WG and the WG/ENR blends was also tested. As investigated by scanning electron microscopy (SEM), the results revealed more compatibility between WG and ENR compared with NR. The elongation at break, impact strength and water resistance of the WG/ENR blends were found to remarkably increase with respect to the pure WG. Thus, incorporation of ENR into WG could improve toughness and water resistance of WG. Furthermore, the effect of adding glycerol acting as a plasticizer on the mechanical properties and impact strength of the WG/ENR blends was also studied. The blends with glycerol-plasticized WG (WG-Gly/ENR) showed more homogeneous morphologies and superior results in the mechanical properties and impact strength compared with the WG/ENR blends.

  14. Polymeric Endoaortic Paving (PEAP): Mechanical, Thermoforming, and Degradation Properties of Polycaprolactone/Polyurethane Blends for Cardiovascular Applications

    PubMed Central

    Ashton, John H.; Mertz, James A. M.; Harper, John L.; Slepian, Marvin J.; Mills, Joseph L.; McGrath, Dominic V.; Vande Geest, Jonathan P.

    2010-01-01

    Polymeric endoaortic paving (PEAP) is a process by which a polymer is endovascularly delivered and thermoformed to coat or “pave” the lumen of the aorta. This method may offer an improvement to conventional endoaortic therapy in allowing conformal graft application with reduced risk of endoleak and customization to complex patient geometries. Polycaprolactone (PCL)/polyurethane (PU) blends of various blend ratios were assessed as a potential material for PEAP by characterizing their mechanical, thermoforming, and degradation properties. Biaxial tension testing revealed that the blends' stiffness is similar to that of aortic tissue, is higher for blends with more PCL content, and may be affected by thermoforming and degradation. Tubes of blends were able to maintain a higher diameter increase after thermoforming at higher PCL content and higher heating temperatures; 50/50 blend tubes heated to 55°C were able to maintain 90% of the diameter increase applied. Delamination forces of the blends ranged from 41 to 235 N/m2. In a Pseudomonas lipase solution, the 50/50 blend had a 94% lower degradation rate than pure PCL, and the 10/90 blend exhibited no degradation. These results indicate that PEAP, consisting of a PCL/PU blend, may be useful in developing the next generation of endoaortic therapy. PMID:20832506

  15. Effect of Cold-Drawn Fibers on the Self-Reinforcement of PP/LDPE Composites

    NASA Astrophysics Data System (ADS)

    Zhou, Ying-Guo; Su, Bei; Wu, Hai-Hong

    2017-08-01

    In our previous study, a method to fabricate super-ductile polypropylene/low-density polyethylene (PP/LDPE) blends was proposed, and a fiber-shape structure was shown to be formed, presenting necking propagation during tensile testing. In this study, the mechanical properties and thermal behavior of the necking region of tested super-ductile PP/LDPE samples were carefully investigated and further compared with the melt-stretched, untested, and thermo-mechanical-history-removed samples by differential scanning calorimetry and tensile testing. The results suggest that the tested samples have high mechanical properties and are more thermo-mechanically stable than the common PP/LDPE blends and melt-stretched samples. Additionally, to investigate their structure-property relationship, the necking region of the tested samples was further characterized by scanning electron microscopy and hot-stage polarized light microscopy. It can be concluded that the variation of the microstructure can be attributed to the cold-drawn fibers (CDFs), which were more stable thermally, formed during the tensile test. Furthermore, the CDFs were used for the filler in PP/LDPE blends. The experimental results of the different PP/LDPE composites indicate that the CDFs are a good reinforcement candidate and have the ability to improve the mechanical properties of the PP/LDPE blends.

  16. Impact of higher alcohols blended in gasoline on light-duty vehicle exhaust emissions.

    PubMed

    Ratcliff, Matthew A; Luecke, Jon; Williams, Aaron; Christensen, Earl; Yanowitz, Janet; Reek, Aaron; McCormick, Robert L

    2013-12-03

    Certification gasoline was splash blended with alcohols to produce four blends: ethanol (16 vol%), n-butanol (17 vol%), i-butanol (21 vol%), and an i-butanol (12 vol%)/ethanol (7 vol%) mixture; these fuels were tested in a 2009 Honda Odyssey (a Tier 2 Bin 5 vehicle) over triplicate LA92 cycles. Emissions of oxides of nitrogen, carbon monoxide, non-methane organic gases (NMOG), unburned alcohols, carbonyls, and C1-C8 hydrocarbons (particularly 1,3-butadiene and benzene) were determined. Large, statistically significant fuel effects on regulated emissions were a 29% reduction in CO from E16 and a 60% increase in formaldehyde emissions from i-butanol, compared to certification gasoline. Ethanol produced the highest unburned alcohol emissions of 1.38 mg/mile ethanol, while butanols produced much lower unburned alcohol emissions (0.17 mg/mile n-butanol, and 0.30 mg/mile i-butanol); these reductions were offset by higher emissions of carbonyls. Formaldehyde, acetaldehyde, and butyraldehyde were the most significant carbonyls from the n-butanol blend, while formaldehyde, acetone, and 2-methylpropanal were the most significant from the i-butanol blend. The 12% i-butanol/7% ethanol blend was designed to produce no increase in gasoline vapor pressure. This fuel's exhaust emissions contained the lowest total oxygenates among the alcohol blends and the lowest NMOG of all fuels tested.

  17. Investigation into the fractionation of refrigerant blends. Final technical report, March 1994--December 1995

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Biancardi, F.R.; Michels, H.; Sienel, T.

    1996-01-01

    As a means of complying with current and impending national and international environmental regulations restricting the use and disposal of conventional CFC and HCFC refrigerants which contribute to the global ozone depletion effects, the HVAC industry is vigorously evaluating and testing BFC refrigerant blends. While analyses and system performance tools have shown that BFC refrigerant blends offer certain performance, capacity and operational advantages, there are significant possible service and operational issues that are raised by the use of blends. Many of these issues occur due to the fractionation of the blends. Therefore, the objective of this program is to conductmore » analyses and experimental tests aimed at understanding these issues, develop approaches or techniques to predict these effects and convey to the industry safe and reliable approaches. As a result, analytical models, verified by laboratory data, have been developed that predict the fractionation effects of HFC refrigerant blends when (1) exposed to selected POE lubricants, (2) during the system charging process from large liquid containers, and (3) during system startup, operation and shutdown within various system components (where two-phase refrigerant exists), and during selected system and component leakage scenarios. Model predictions and experimental results are presented for HFC refrigerant blends containing HFC-32, HFC-134a, and HFC-125 and the data are generalized for various operating conditions and scenarios.« less

  18. Resistance surveillance program report for selected European nations (2011).

    PubMed

    Jones, Ronald N; Flonta, Mirela; Gurler, Nazahat; Cepparulo, Mario; Mendes, Rodrigo E; Castanheira, Mariana

    2014-04-01

    In the European component of the Regional Resistance Surveillance study for 2011, a total of 21 countries were monitored for antimicrobial resistance patterns including Belgium, Bulgaria (BU), Croatia, Czech Republic, France (F), Germany (GE), Greece (GR), Ireland (IR), Israel (IS), Italy (IT), Poland (PO), Portugal (PT), Romania (RO), Russia (RU), Slovakia (SK), Slovenia, Spain, Sweden (SW), Turkey (T), Ukraine, and United Kingdom. Results from testing 12,572 strains (100 [BU] to 1535 [F] per nation) were interpreted by contemporary published breakpoints. Samples from 47 hospitals were reference tested against agents such as amikacin (AMK), cefoperazone/sulbactam (C/S), colistin (COL), levofloxacin, linezolid (LZD), tigecycline (TIG), vancomycin (VAN), and 21 others. Among Staphylococcus aureus, LZD (MIC90, 2 μg/mL), TIG (MIC90, 0.12 μg/mL), and VAN (MIC90, 1 μg/mL) exhibited complete coverage and methicillin resistance rates among nations (average, 31%) ranged from 0.9% (SW) to 60.0-60.2% (PT, SK). Seven LZD-resistant coagulase-negative staphylococci (only 1.1% resistance overall) were noted in 5 nations, and a Staphylococcus simulans strain (MIC, 8 μg/mL from RO) had L3 mutations (N130D, G152A, F147S, A157R); also 6 LZD-resistant enterococci were detected in 3 countries (GE, IR, T). VAN-resistant enterococci (10% overall; 84% VanA) were found in 14 countries, highest in GE and IR (23.0%). The ESBL phenotype rate for Escherichia coli was 20.1% (range, 0.9% [SW] to 70.0-89.7% [BU, RU]), best inhibited by COL (100.0% S), TIG (100.0%), AMK (83.3-94.1%), C/S (81.0%), and carbapenems (>99.0%; resistant strains in IS and T). Klebsiella spp. had greater ESBL rates (45.7% overall, range 2.5-100.0%), as well as carbapenem resistance (8.3% overall, greatest in BU, GR, IS, IT, PO, RO, RU, T). Non-fermentative Gram-negative bacilli (Pseudomonas aeruginosa, Acinetobacter [ACB]) were generally less susceptible, except against COL (99.2-99.6% S) and TIG (95.0% inhibited at ≤2 μg/mL; ACB only). The following carbapenemases were detected: VIM-1 (2 countries); IMP-1 (1 from T); KPC-2 or -3 (2 countries); VIM-4 (1 from PO), NDM-1 (2 in RO; 2 centers); and OXA-48 or -162 (5 from T; 2 centers). European surveillance sampling demonstrates a wide array of resistant isolates, less prevalent among Gram-positive cocci that remain inhibited by several available agents. However, beta-lactamase-mediated mechanisms have spread widely among Gram-negative bacilli, especially across the Eastern and Southern European nations, severely limiting infection chemotherapy and necessitating escalated antimicrobial stewardship. © 2014.

  19. Practical Skills Training in Agricultural Education--A Comparison between Traditional and Blended Approaches

    ERIC Educational Resources Information Center

    Deegan, Donna; Wims, Padraig; Pettit, Tony

    2016-01-01

    Purpose: In this article the use of blended learning multimedia materials as an education tool was compared with the traditional approach for skills training. Design/Methodology/Approach: This study was conducted in Ireland using a pre-test, post-test experimental design. All students were instructed on how to complete two skills using either a…

  20. Preparation and tensile properties of linear low density polyethylene/rambutan peels (Nephelium chryseum Blum.) flour blends

    NASA Astrophysics Data System (ADS)

    Nadhirah, A. Ainatun.; Sam, S. T.; Noriman, N. Z.; Voon, C. H.; Samera, S. S.

    2015-05-01

    The effect of rambutan peels flour (RPF) content on the tensile properties of linear low density polyethylene filled with rambutan peel flour was studied. RPF was melt blended with linear low-density polyethylene (LLDPE). LLDPE/RPF blends were prepared by using internal mixer (brabender) at 160 °C with the flour content ranged from 0 to 15 wt%. The tensile properties were tested by using a universal testing machine (UTM) according to ASTM D638. The highest tensile strength was observed for pure LLDPE while the tensile strength LLDPE/RPF decreased gradually with the addition of rambutan peels flour content from 0% to 15%. Young's modulus of 63 µm to 250 µm rambutan peels blends with LLDPE with the fiber loading of 0 - 15 wt% increased with increasing fiber loading.

  1. Effect of Pertalite-Spiritus Blend Fuel on Performance of Single Cylinder Spark Ignition Engine

    NASA Astrophysics Data System (ADS)

    Wibowo, H.; Susastriawan, A. A. P.; Andrian, D.

    2018-02-01

    This work aims to experimentally investigate an effect of Spiritus and Pertalite blend on engine’s performance (brake horsepower and torque, specific fuel consumption rate, and exhaust gas emission). The tests are conducted at 3000-7000 rpm for four different fuels, i.e., pertalite, 95%P-5%S, 90%P-10%S, and 85%P-15%S to obtain an optimum ratio of the Pertalite-Spiritus blend. The blend ratios of Pertalite (P) and Spiritus (S) are measured by volume. The result shows that addition of 15% Spiritus (by volume) on Pertalilte can enhance the combustion process of the blend hence increasing engine’s brake horsepower and decreasing specific fuel consumption rate. However, engine’s torque is lower when using the blend 85%P-15%S if compared with using Pertalite.

  2. Experimental assessment of non-edible candlenut biodiesel and its blend characteristics as diesel engine fuel.

    PubMed

    Imdadul, H K; Zulkifli, N W M; Masjuki, H H; Kalam, M A; Kamruzzaman, M; Rashed, M M; Rashedul, H K; Alwi, Azham

    2017-01-01

    Exploring new renewable energy sources as a substitute of petroleum reserves is necessary due to fulfilling the oncoming energy needs for industry and transportation systems. In this quest, a lot of research is going on to expose different kinds of new biodiesel sources. The non-edible oil from candlenut possesses the potential as a feedstock for biodiesel production. The present study aims to produce biodiesel from crude candlenut oil by using two-step transesterification process, and 10%, 20%, and 30% of biodiesel were mixed with diesel fuel as test blends for engine testing. Fourier transform infrared (FTIR) and gas chromatography (GC) were performed and analyzed to characterize the biodiesel. Also, the fuel properties of biodiesel and its blends were measured and compared with the specified standards. The thermal stability of the fuel blends was measured by thermogravimetric analysis (TGA) and differential scan calorimetry (DSC) analysis. Engine characteristics were measured in a Yanmar TF120M single cylinder direct injection (DI) diesel engine. Biodiesel produced from candlenut oil contained 15% free fatty acid (FFA), and two-step esterification and transesterification were used. FTIR and GC remarked the biodiesels' existing functional groups and fatty acid methyl ester (FAME) composition. The thermal analysis of the biodiesel blends certified about the blends' stability regarding thermal degradation, melting and crystallization temperature, oxidative temperature, and storage stability. The brake power (BP), brake specific fuel consumption (BSFC), and brake thermal efficiency (BTE) of the biodiesel blends decreased slightly with an increasing pattern of nitric oxide (NO) emission. However, the hydrocarbon (HC) and carbon monoxides (CO) of biodiesel blends were found decreased.

  3. Attraction of female grapevine moth to common and specific olfactory cues from 2 host plants.

    PubMed

    Tasin, Marco; Bäckman, Anna-Carin; Anfora, Gianfranco; Carlin, Silvia; Ioriatti, Claudio; Witzgall, Peter

    2010-01-01

    In herbivorous insects with more than 1 host plant, attraction to host odor could conceptually be mediated by common compounds, by specific compounds released by each plant or by combinations of common and specific compounds. We have compared the attraction of female grapevine moth, Lobesia botrana, with specific and common (shared) odors from 2 different plants: a wild host (Daphne gnidium) and a recently colonized host (Vitis vinifera). Odor blends eliciting female attraction to V. vinifera have previously been identified. In this study, olfactory cues from D. gnidium were identified by electroantennographic detection and chemical analysis. The attraction of mated females to synthetic odor blends was then tested in a wind tunnel bioassay. Female attraction was elicited by a blend of compounds released by both from D. gnidium and V. vinifera and by 2 blends with the compounds released specifically from each host. However, more complete odor blends of the 2 plants elicited stronger attraction. The common compounds in combination with the specific compounds of D. gnidium were the most attractive blend. This blend was tested with the common compounds presented both in the ratio emitted by D. gnidium and by V. vinifera, but there was no difference in female attraction. Our findings suggest that specific as well as common plant odor cues play a role in L. botrana host recognition and that there is plasticity in attraction to partial blends. The results are discussed in relation to mechanisms behind host odor recognition and the evolution of insect-plant associations.

  4. Power-grade butanol recovery and utilization

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Noon, R.

    1982-02-12

    As an alternative to the traditional recovery systems, it was proposed in a previous publication that the n-butanol/acetone/ethanol fermentation products could be recovered as a power grade fuel blend and used directly as a fuel. This would affect a savings in process energy requirements because each chemical component would not have to be processed individually to technical grade purity. Further, some residual water could be tolerated in the fuel blend. To develop such a power grade fuel recovery scheme beyond the conceptual stage, the Energy Research and Resource Division of the Kansas Energy Office undertook a two-fold program to demonstratemore » and test a power grade butanol/acetone/ethanol fuel recovery system, and further to demonstrate the feasibility of using the fuel blend in a standard type engine. A development program was initiated to accomplish the following objectives: design and test an operational power grade butanol recovery plant that would operate at one liter per hour output; and test and assess the performance of power grade butanol in a spark ignition automotive engine. This project has demonstrated that recovery of a power grade butanol fuel blend is simple and can be accomplished at a considered energy advantage over ethanol. It was further demonstrated that such a power grade blend works well in a typical spark ignition engine.« less

  5. Managing variability in algal biomass production through drying and stabilization of feedstock blends

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wahlen, Bradley D.; Roni, Mohammad S.; Cafferty, Kara G.

    The uncertainty and variability of algal biomass production presents several challenges to the algal biofuel industry including equipment scaling and the ability to provide a consistent feedstock stream for conversion. Blended feedstocks containing both algal and terrestrial biomass may provide a cost-effective method to manage variability of algal biomass production. The hypothesis is that mixing of algae with terrestrial biomass has the potential to create blends with rheologic (flowability) properties similar to terrestrial feedstock and that blends with the consistency of terrestrial biomass can be dried using established low-cost drying systems. To test this hypothesis and its technical feasibility, prototypemore » bench scale simulated drum dyers were designed and tested with blends of algae and ground pine. Scenedesmus dimorphus biomass was used as the algal feedstock, while 2 mm grind pine was used as the terrestrial feedstock. Pine was selected as the representative terrestrial feedstock to leverage independent HTL research using pine feedstock. In these studies, blends up to 60% algae produced drying curves similar to those of pine alone, and reached dryness (2% moisture) much more rapidly than algae alone. Thermogravimetric analyses performed on these feedstocks provided drying curves consistent with the simulated drum dryers. In addition, observable rheologic properties at the time of blending served as an indicator of drying performance, as those blends with texture similar to pine also dried similar to the pine control. Logistics analyses performed to determine cost and availability of feedstock materials for blending at production scale further indicate the potential of this approach. Lastly, our results indicate that blending of algae with terrestrial biomass enables the use of low cost dryers and has the potential to improve overall algal biofuel economics by capturing the value of excess biomass produced during periods of high productivity and by decoupling of algal production farms and conversion facilities.« less

  6. Computed Tomography Window Blending: Feasibility in Thoracic Trauma.

    PubMed

    Mandell, Jacob C; Wortman, Jeremy R; Rocha, Tatiana C; Folio, Les R; Andriole, Katherine P; Khurana, Bharti

    2018-02-07

    This study aims to demonstrate the feasibility of processing computed tomography (CT) images with a custom window blending algorithm that combines soft-tissue, bone, and lung window settings into a single image; to compare the time for interpretation of chest CT for thoracic trauma with window blending and conventional window settings; and to assess diagnostic performance of both techniques. Adobe Photoshop was scripted to process axial DICOM images from retrospective contrast-enhanced chest CTs performed for trauma with a window-blending algorithm. Two emergency radiologists independently interpreted the axial images from 103 chest CTs with both blended and conventional windows. Interpretation time and diagnostic performance were compared with Wilcoxon signed-rank test and McNemar test, respectively. Agreement with Nexus CT Chest injury severity was assessed with the weighted kappa statistic. A total of 13,295 images were processed without error. Interpretation was faster with window blending, resulting in a 20.3% time saving (P < .001), with no difference in diagnostic performance, within the power of the study to detect a difference in sensitivity of 5% as determined by post hoc power analysis. The sensitivity of the window-blended cases was 82.7%, compared to 81.6% for conventional windows. The specificity of the window-blended cases was 93.1%, compared to 90.5% for conventional windows. All injuries of major clinical significance (per Nexus CT Chest criteria) were correctly identified in all reading sessions, and all negative cases were correctly classified. All readers demonstrated near-perfect agreement with injury severity classification with both window settings. In this pilot study utilizing retrospective data, window blending allows faster preliminary interpretation of axial chest CT performed for trauma, with no significant difference in diagnostic performance compared to conventional window settings. Future studies would be required to assess the utility of window blending in clinical practice. Copyright © 2018 The Association of University Radiologists. All rights reserved.

  7. Managing variability in algal biomass production through drying and stabilization of feedstock blends

    DOE PAGES

    Wahlen, Bradley D.; Roni, Mohammad S.; Cafferty, Kara G.; ...

    2017-03-22

    The uncertainty and variability of algal biomass production presents several challenges to the algal biofuel industry including equipment scaling and the ability to provide a consistent feedstock stream for conversion. Blended feedstocks containing both algal and terrestrial biomass may provide a cost-effective method to manage variability of algal biomass production. The hypothesis is that mixing of algae with terrestrial biomass has the potential to create blends with rheologic (flowability) properties similar to terrestrial feedstock and that blends with the consistency of terrestrial biomass can be dried using established low-cost drying systems. To test this hypothesis and its technical feasibility, prototypemore » bench scale simulated drum dyers were designed and tested with blends of algae and ground pine. Scenedesmus dimorphus biomass was used as the algal feedstock, while 2 mm grind pine was used as the terrestrial feedstock. Pine was selected as the representative terrestrial feedstock to leverage independent HTL research using pine feedstock. In these studies, blends up to 60% algae produced drying curves similar to those of pine alone, and reached dryness (2% moisture) much more rapidly than algae alone. Thermogravimetric analyses performed on these feedstocks provided drying curves consistent with the simulated drum dryers. In addition, observable rheologic properties at the time of blending served as an indicator of drying performance, as those blends with texture similar to pine also dried similar to the pine control. Logistics analyses performed to determine cost and availability of feedstock materials for blending at production scale further indicate the potential of this approach. Lastly, our results indicate that blending of algae with terrestrial biomass enables the use of low cost dryers and has the potential to improve overall algal biofuel economics by capturing the value of excess biomass produced during periods of high productivity and by decoupling of algal production farms and conversion facilities.« less

  8. Improving Education in Medical Statistics: Implementing a Blended Learning Model in the Existing Curriculum

    PubMed Central

    Milic, Natasa M.; Trajkovic, Goran Z.; Bukumiric, Zoran M.; Cirkovic, Andja; Nikolic, Ivan M.; Milin, Jelena S.; Milic, Nikola V.; Savic, Marko D.; Corac, Aleksandar M.; Marinkovic, Jelena M.; Stanisavljevic, Dejana M.

    2016-01-01

    Background Although recent studies report on the benefits of blended learning in improving medical student education, there is still no empirical evidence on the relative effectiveness of blended over traditional learning approaches in medical statistics. We implemented blended along with on-site (i.e. face-to-face) learning to further assess the potential value of web-based learning in medical statistics. Methods This was a prospective study conducted with third year medical undergraduate students attending the Faculty of Medicine, University of Belgrade, who passed (440 of 545) the final exam of the obligatory introductory statistics course during 2013–14. Student statistics achievements were stratified based on the two methods of education delivery: blended learning and on-site learning. Blended learning included a combination of face-to-face and distance learning methodologies integrated into a single course. Results Mean exam scores for the blended learning student group were higher than for the on-site student group for both final statistics score (89.36±6.60 vs. 86.06±8.48; p = 0.001) and knowledge test score (7.88±1.30 vs. 7.51±1.36; p = 0.023) with a medium effect size. There were no differences in sex or study duration between the groups. Current grade point average (GPA) was higher in the blended group. In a multivariable regression model, current GPA and knowledge test scores were associated with the final statistics score after adjusting for study duration and learning modality (p<0.001). Conclusion This study provides empirical evidence to support educator decisions to implement different learning environments for teaching medical statistics to undergraduate medical students. Blended and on-site training formats led to similar knowledge acquisition; however, students with higher GPA preferred the technology assisted learning format. Implementation of blended learning approaches can be considered an attractive, cost-effective, and efficient alternative to traditional classroom training in medical statistics. PMID:26859832

  9. Improving Education in Medical Statistics: Implementing a Blended Learning Model in the Existing Curriculum.

    PubMed

    Milic, Natasa M; Trajkovic, Goran Z; Bukumiric, Zoran M; Cirkovic, Andja; Nikolic, Ivan M; Milin, Jelena S; Milic, Nikola V; Savic, Marko D; Corac, Aleksandar M; Marinkovic, Jelena M; Stanisavljevic, Dejana M

    2016-01-01

    Although recent studies report on the benefits of blended learning in improving medical student education, there is still no empirical evidence on the relative effectiveness of blended over traditional learning approaches in medical statistics. We implemented blended along with on-site (i.e. face-to-face) learning to further assess the potential value of web-based learning in medical statistics. This was a prospective study conducted with third year medical undergraduate students attending the Faculty of Medicine, University of Belgrade, who passed (440 of 545) the final exam of the obligatory introductory statistics course during 2013-14. Student statistics achievements were stratified based on the two methods of education delivery: blended learning and on-site learning. Blended learning included a combination of face-to-face and distance learning methodologies integrated into a single course. Mean exam scores for the blended learning student group were higher than for the on-site student group for both final statistics score (89.36±6.60 vs. 86.06±8.48; p = 0.001) and knowledge test score (7.88±1.30 vs. 7.51±1.36; p = 0.023) with a medium effect size. There were no differences in sex or study duration between the groups. Current grade point average (GPA) was higher in the blended group. In a multivariable regression model, current GPA and knowledge test scores were associated with the final statistics score after adjusting for study duration and learning modality (p<0.001). This study provides empirical evidence to support educator decisions to implement different learning environments for teaching medical statistics to undergraduate medical students. Blended and on-site training formats led to similar knowledge acquisition; however, students with higher GPA preferred the technology assisted learning format. Implementation of blended learning approaches can be considered an attractive, cost-effective, and efficient alternative to traditional classroom training in medical statistics.

  10. 40 CFR 80.46 - Measurement of reformulated gasoline and conventional gasoline fuel parameters.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... D7039-13, Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence...

  11. Physicochemical and toxicological characteristics of particulate matter emitted from a non-road diesel engine: comparative evaluation of biodiesel-diesel and butanol-diesel blends.

    PubMed

    Zhang, Zhi-Hui; Balasubramanian, Rajasekhar

    2014-01-15

    Combustion experiments were conducted to evaluate the effects of using blends of ultralow sulfur diesel (ULSD) with biodiesel or n-butanol on physicochemical and toxicological characteristics of particulate emissions from a non-road diesel engine. The results indicated that compared to ULSD, both the blended fuels could effectively reduce the particulate mass and elemental carbon emissions, with butanol being more effective than biodiesel. The proportion of organic carbon and volatile organic compounds in particles increased for both blended fuels. However, biodiesel blended fuels showed lower total particle-phase polycyclic aromatic hydrocarbons (PAHs) emissions. The total number emissions of particles ≤560nm in diameter decreased gradually for the butanol blended fuels, but increased significantly for the biodiesel blended fuels. Both the blended fuels indicated lower soot ignition temperature and activation energy. All the particle extracts showed a decline in cell viability with the increased dose. However, the change in cell viability among test fuels is not statistically significant different with the exception of DB-4 (biodiesel-diesel blend containing 4% oxygen) used at 75% engine load. Copyright © 2013 Elsevier B.V. All rights reserved.

  12. Characterization of an Experimental Referee Broadened Specification (ERBS) aviation turbine fuel and ERBS fuel blends

    NASA Technical Reports Server (NTRS)

    Seng, G. T.

    1982-01-01

    Characterization data and comparisons of these data are presented for three individual lots of a research test fuel designated as an Experimental Referee Broadened Specification (ERBS) aviation turbine fuel. This research fuel, which is a blend of kerosene and hydrotreated catalytic gas oil, is a representation of a kerojet fuel with broadened properties. To lower the hydrogen content of the ERBS fuel, a blending stock, composed of xylene bottoms and hydrotreated catalytic gas oil, was developed and employed to produce two different ERBS fuel blends. The ERBS fuel blends and the blending stock were also characterized and the results for the blends are compared to those of the original ERBS fuel. The characterization results indicate that with the exception of the freezing point for ERBS lot 2, which was slightly high, the three lots, produced over a 2 year period, met all general fuel requirements. However, although the properties of the fuels were found to be fairly consistent, there were differences in composition. Similarly, all major requirements for the ERBS fuel blends were met or closely approached, and the properties of the blended fuels were found to generally reflect those expected for the proportions of ERBS fuel and blending stock used in their production.

  13. Physical characterization and modeling of chitosan/peg blends for injectable scaffolds.

    PubMed

    Lima, Daniel B; Almeida, Renata D; Pasquali, Matheus; Borges, Sílvia P; Fook, Marcus L; Lisboa, Hugo M

    2018-06-01

    Injectable scaffolds find many applications on the biomedical field due to several advantages on preformed scaffolds such as being able to fill any defect can be used in minimal invasion surgeries and are ready to use products. The most critical parameter for an injectable scaffold usage is its injectability, which can be related with rheological properties. Therefore, the objective of the present work was to increase knowledge about the critical parameters influencing injectability of biopolymers used for injectable scaffolds. Rheological and mechanical properties of a biopolymer blend in combination with injectability tests for a given design space controlled by the concentrations of both polymers and temperatures was made. Then those results were modeled to better understand the impact of parameters on injectability. The biopolymer blend chosen was Chitosan physically blended with Poly(ethylene glycol) where variations of both polymer concentrations and molecular weights were tested. Rheological and mechanical properties of all samples were determined, together with the injection force using a compression test at different injection conditions. All solutions were clear and transparent suggesting perfect miscibility. Rheological results were modeled using Ostwald-Waelle law and revealed a shear thinning pseudo-plastic solution at any composition and temperature, being chitosan concentration the most influencing variable. Compression tests results revealed mean injection forces ranging from 9.9 ± 0.06N to 29.9 ± 0.65N and it was possible to accurately estimate those results. Simulations revealed draw speed as the most influencing parameter. Cell viability tests revealed a non-cytotoxic biopolymer blend. Copyright © 2018 Elsevier Ltd. All rights reserved.

  14. Sampling bias in blending validation and a different approach to homogeneity assessment.

    PubMed

    Kraemer, J; Svensson, J R; Melgaard, H

    1999-02-01

    Sampling of batches studied for validation is reported. A thief particularly suited for granules, rather than cohesive powders, was used in the study. It is shown, as has been demonstrated in the past, that traditional 1x to 3x thief sampling of a blend is biased, and that the bias decreases as the sample size increases. It is shown that taking 50 samples of tablets after blending and testing this subpopulation for normality is a discriminating manner of testing for homogeneity. As a criterion, it is better than sampling at mixer or drum stage would be even if an unbiased sampling device were available.

  15. Publications - GMC 353 | Alaska Division of Geological & Geophysical

    Science.gov Websites

    and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a Umiat (Blend, unknown well number) and from US Navy Umiat Ruby #1 (renamed Umiat Test Well #4); both Samples from US Navy Umiat (Blend, unknown well number) and from US Navy Umiat Ruby #1 (renamed Umiat Test

  16. Blended Learning Versus Traditional Lecture in Introductory Nursing Pathophysiology Courses.

    PubMed

    Blissitt, Andrea Marie

    2016-04-01

    Currently, many undergraduate nursing courses use blended-learning course formats with success; however, little evidence exists that supports the use of blended formats in introductory pathophysiology courses. The purpose of this study was to compare the scores on pre- and posttests and course satisfaction between traditional and blended course formats in an introductory nursing pathophysiology course. This study used a quantitative, quasi-experimental, nonrandomized control group, pretest-posttest design. Analysis of covariance compared pre- and posttest scores, and a t test for independent samples compared students' reported course satisfaction of the traditional and blended course formats. Results indicated that the differences in posttest scores were not statistically significant between groups. Students in the traditional group reported statistically significantly higher satisfaction ratings than students in the blended group. The results of this study support the need for further research of using blended learning in introductory pathophysiology courses in undergraduate baccalaureate nursing programs. Further investigation into how satisfaction is affected by course formats is needed. Copyright 2016, SLACK Incorporated.

  17. Impact-induced fracture mechanisms of immiscible PC/ABS (50/50) blends

    NASA Astrophysics Data System (ADS)

    Machmud, M. N.; Omiya, M.; Inoue, H.; Kishimoto, K.

    2018-03-01

    This paper presents a study on fracture mechanisms of polycarbonate (PC)/acrylonitrile-butadiene-styrene (ABS) (50/50) blends with different ABS types under a drop weight impact test (DWIT) using a circular sheet specimen. Formation of secondary crack indicated by a stress-whitening layer on the mid-plane of scattered specimens and secondary surface of fracture perpendicular to primary fracture surface were captured under scanning electron microscope (SEM). Although the both blends finally failed in brittle modes, SEM observation showed that their secondary fracture mechanisms were completely different. Observation through the thickness of the etched PC/ABS specimen samples using SEM also clearly showed that PC and ABS were immiscible. The immiscibility between PC and ABS was indicated by presence of their layer structures through the thickness of the blends. It was revealed that layer of ABS structure was influenced by size of rubber particle and this latter parameter then affected microstructure and fracture mechanisms of the blends. Impact-induced fracture mechanisms of the blends due to such microstructures are discussed in this paper. It was also pointed out that the secondary cracking was likely caused by interface delamination between PC and ABS layers in the core due to transverse shear stress generated during the impact test.

  18. Biodegradation of diesel/biodiesel blends by a consortium of hydrocarbon degraders: effect of the type of blend and the addition of biosurfactants.

    PubMed

    Owsianiak, Mikołaj; Chrzanowski, Łukasz; Szulc, Alicja; Staniewski, Jacek; Olszanowski, Andrzej; Olejnik-Schmidt, Agnieszka K; Heipieper, Hermann J

    2009-02-01

    Biodegradation experiments for diesel/biodiesel blends in liquid cultures by-petroleum degrading microbial consortium showed that for low amendments of biodiesel (10%) the overall biodegradation efficiency of the mixture after seven days was lower than for petroleum diesel fuel. Preferential usage of methyl esters in the broad biodiesel concentration range and diminished biodegradation of petroleum hydrocarbons for 10% biodiesel blend was confirmed. Rhamnolipids improved biodegradation efficiency only for blends with low content of biodiesel. Emulsion formation experiments showed that biodiesel amendments significantly affected dispersion of fuel mixtures in water. The presence of rhamnolipids biosurfactant affected stability of such emulsions and altered cell surface properties of tested consortium.

  19. Influence of adipic acid on tensile and morphology properties of linear low density polyethylene/rambutan peels flour blends

    NASA Astrophysics Data System (ADS)

    Nadhirah, A. A.; Sam, S. T.; Noriman, N. Z.; Ragunathan, S.; Ismail, H.

    2015-07-01

    This study investigate about the tensile and morphological properties of degradable polymer produced from linear low density polyethylene/rambutan peel flour (LLDPE/RPF) blends and adipic acid (AA) was used as a compatibilizer by varying the rambutan peel flour (RPF) amount from 0-25wt%. The samples were subjected to tensile and morphological tests. AA compatibilized showed higher strength compared to uncompatibilized blends. The Young's modulus for LLDPE/RPF blends increased with increasing flour content. However, the addition of adipic acid had reduced the Young's Modulus.

  20. Effect of some Turkish vegetable oil-diesel fuel blends on exhaust emissions

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ergeneman, M.; Oezaktas, T.; Cigizoglu, K.B.

    1997-10-01

    For different types of vegetable oils of Turkish origin (sunflower, corn, soybean, and olive oil) were blended with grade No. 2-D diesel fuel at a ratio of 20/80 (v/v). The effect of the compression ratio on exhaust emissions is investigated in an American Society for Testing and Materials (ASTM)-cooperative fuel research (CFR) engine working with the mentioned fuel blends and a baseline diesel fuel. A decrease in soot, CO, CO{sub 2}, and HC emissions and an increase in NO{sub x} emissions have been observed for fuel blends compared to diesel fuel.

  1. X-48C Hybrid - Blended Wing Body Demonstrator

    NASA Image and Video Library

    2013-02-28

    The NASA-Boeing X-48C Hybrid/Blended Wing Body research aircraft banked left during one of its final test flights over Edwards Air Force Base from NASA's Dryden Flight Research Center on Feb. 28, 2013.

  2. Spices in a Product Affect Emotions: A Study with an Extruded Snack Product †.

    PubMed

    Bell, Brandon; Adhikari, Koushik; Chambers, Edgar; Alavi, Sajid; King, Silvia; Haub, Mark

    2017-08-18

    Food commonly is associated with emotion. The study was designed to determine if a spice blend (cinnamon, ginger, nutmeg, and cloves) high in antioxidants can evoke changes in consumer emotions. This was an exploratory study to determine the effects of these four spices on emotions. Three extruded, dry snack products containing 0, 4, or a 5% spice blend were tested. One day of hedonic and just-about-right evaluations ( n = 100), followed by three days of emotion testing were conducted. A human clinical trial ( n = 10), using the control and the 4% samples, measured total antioxidant capacity and blood glucose levels. The emotion "Satisfied" increased significantly in the 5% blend, showing an effect of a higher spice content. The 4% blend was significantly higher in total antioxidant capacity than the baseline, but blood glucose levels were not significantly different.

  3. Spices in a Product Affect Emotions: A Study with an Extruded Snack Product †

    PubMed Central

    Bell, Brandon; Adhikari, Koushik; Alavi, Sajid; King, Silvia; Haub, Mark

    2017-01-01

    Food commonly is associated with emotion. The study was designed to determine if a spice blend (cinnamon, ginger, nutmeg, and cloves) high in antioxidants can evoke changes in consumer emotions. This was an exploratory study to determine the effects of these four spices on emotions. Three extruded, dry snack products containing 0, 4, or a 5% spice blend were tested. One day of hedonic and just-about-right evaluations (n = 100), followed by three days of emotion testing were conducted. A human clinical trial (n = 10), using the control and the 4% samples, measured total antioxidant capacity and blood glucose levels. The emotion “Satisfied” increased significantly in the 5% blend, showing an effect of a higher spice content. The 4% blend was significantly higher in total antioxidant capacity than the baseline, but blood glucose levels were not significantly different. PMID:28820459

  4. Blended Learning Educational Format for Third-Year Pediatrics Clinical Rotation.

    PubMed

    Langenau, Erik E; Lee, Robert; Fults, Marci

    2017-04-01

    Traditional medical education is shifting to incorporate learning technologies and online educational activities with traditional face-to-face clinical instruction to engage students, especially at remote clinical training sites. To describe and evaluate the effectiveness of the blended learning format (combining online and face-to-face instruction) for third-year osteopathic medical students during their pediatric rotation. Third-year medical students who completed the 4-week clerkship in pediatrics during the 2014-2015 academic year were divided into a standard learning group and a blended learning group with online activities (discussion boards, blogs, virtual patient encounters, narrated video presentations, and online training modules). Comprehensive Osteopathic Medical Achievement Test scores and final course grades were compared between the standard learning and blended learning groups. Students in the blended learning group completed a postsurvey regarding their experiences. Of 264 third-year students who completed the 4-week clerkship in pediatrics during the 2014-2015 academic year, 78 (29.5%) participated in the blended learning supplement with online activities. Of 53 students who completed the postsurvey in the blended learning group, 44 (83.0%) agreed or strongly agreed that "The integration of e-learning and face-to-face learning helped me learn pediatrics." Open-ended comments supported this overall satisfaction with the course format; however, 26 of 100 comments reflected a desire to increase the amount of clinical exposure and face-to-face time with patients. No statistical differences were seen between the standard learning (n=186) and blended learning (n=78) groups with regard to Comprehensive Osteopathic Medical Achievement Test scores (P=.321). Compared with the standard learning group, more students in the blended learning group received a final course grade of honors (P=.015). Results of this study support the use of blended learning in a clinical training environment. As more medical educators use blended learning, it is important to investigate the best balance between learning with technology and learning in a face-to-face setting. Online activities may enhance but should never fully replace face-to-face learning with real patients.

  5. Evaluation of the impacts of biodiesel and second generation biofuels on NO(x) emissions for CARB diesel fuels.

    PubMed

    Hajbabaei, Maryam; Johnson, Kent C; Okamoto, Robert A; Mitchell, Alexander; Pullman, Marcie; Durbin, Thomas D

    2012-08-21

    The impact of biodiesel and second generation biofuels on nitrogen oxides (NO(x)) emissions from heavy-duty engines was investigated using a California Air Resources Board (CARB) certified diesel fuel. Two heavy-duty engines, a 2006 engine with no exhaust aftertreatment, and a 2007 engine with a diesel particle filter (DPF), were tested on an engine dynamometer over four different test cycles. Emissions from soy- and animal-based biodiesels, a hydrotreated renewable diesel, and a gas to liquid (GTL) fuel were evaluated at blend levels from 5 to 100%. NO(x) emissions consistently increased with increasing biodiesel blend level, while increasing renewable diesel and GTL blends showed NO(x) emissions reductions with blend level. NO(x) increases ranged from 1.5% to 6.9% for B20, 6.4% to 18.2% for B50, and 14.1% to 47.1% for B100. The soy-biodiesel showed higher NO(x) emissions increases compared to the animal-biodiesel. NO(x) emissions neutrality with the CARB diesel was achieved by blending GTL or renewable diesel fuels with various levels of biodiesel or by using di-tert-butyl peroxide (DTBP). It appears that the impact of biodiesel on NO(x) emissions might be a more important consideration when blended with CARB diesel or similar fuels, and that some form of NO(x) mitigation might be needed for biodiesel blends with such fuels.

  6. Effects of Mid-Level Ethanol Blends on Conventional Vehicle Emissions

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Knoll, K.; West, B.; Huff, S.

    2010-06-01

    Tests were conducted in 2008 on 16 late-model conventional vehicles (1999-2007) to determine short-term effects of mid-level ethanol blends on performance and emissions. Vehicle odometer readings ranged from 10,000 to 100,000 miles, and all vehicles conformed to federal emissions requirements for their federal certification level. The LA92 drive cycle, also known as the Unified Cycle, was used for testing because it more accurately represents real-world acceleration rates and speeds than the Federal Test Procedure. Test fuels were splash-blends of up to 20 volume percent ethanol with federal certification gasoline. Both regulated and unregulated air-toxic emissions were measured. For the 16-vehiclemore » fleet, increasing ethanol content resulted in reductions in average composite emissions of both nonmethane hydrocarbons and carbon monoxide and increases in average emissions of ethanol and aldehydes.« less

  7. A Rigorous Test of the Fit of the Circumplex Model to Big Five Personality Data: Theoretical and Methodological Issues and Two Large Sample Empirical Tests.

    PubMed

    DeGeest, David Scott; Schmidt, Frank

    2015-01-01

    Our objective was to apply the rigorous test developed by Browne (1992) to determine whether the circumplex model fits Big Five personality data. This test has yet to be applied to personality data. Another objective was to determine whether blended items explained correlations among the Big Five traits. We used two working adult samples, the Eugene-Springfield Community Sample and the Professional Worker Career Experience Survey. Fit to the circumplex was tested via Browne's (1992) procedure. Circumplexes were graphed to identify items with loadings on multiple traits (blended items), and to determine whether removing these items changed five-factor model (FFM) trait intercorrelations. In both samples, the circumplex structure fit the FFM traits well. Each sample had items with dual-factor loadings (8 items in the first sample, 21 in the second). Removing blended items had little effect on construct-level intercorrelations among FFM traits. We conclude that rigorous tests show that the fit of personality data to the circumplex model is good. This finding means the circumplex model is competitive with the factor model in understanding the organization of personality traits. The circumplex structure also provides a theoretically and empirically sound rationale for evaluating intercorrelations among FFM traits. Even after eliminating blended items, FFM personality traits remained correlated.

  8. Quantification of synthetic cannabinoids in herbal smoking blends using NMR.

    PubMed

    Dunne, Simon J; Rosengren-Holmberg, Jenny P

    2017-05-01

    Herbal smoking blends containing synthetic cannabinoids have become popular alternatives to marijuana. These products were previously sold in pre-packaged foil bags, but nowadays seizures usually contain synthetic cannabinoid powders together with unprepared plant materials. A question often raised by the Swedish police is how much smoking blend can be prepared from certain amounts of banned substance, in order to establish the severity of the crime. To address this question, information about the synthetic cannabinoid content in both the powder and the prepared herbal blends is necessary. In this work, an extraction procedure compatible with direct NMR quantification of synthetic cannabinoids in herbal smoking blends was developed. Extraction media, time and efficiency were tested for different carrier materials containing representative synthetic cannabinoids. The developed protocol utilizes a 30 min extraction step in d 4 -methanol in presence of internal standard allowing direct quantitation of the extract using NMR. The accuracy of the developed method was tested using in-house prepared herbal smoking blends. The results showed deviations less than 0.2% from the actual content, proving that the method is sufficiently accurate for these quantifications. Using this method, ten synthetic cannabinoids present in sixty-three different herbal blends seized by the Swedish police between October 2012 and April 2015 were quantified. Obtained results showed a variation in cannabinoid contents from 1.5% (w/w) for mixtures containing MDMB-CHMICA to over 5% (w/w) for mixtures containing 5F-AKB-48. This is important information for forensic experts when making theoretical calculations of production quantities in legal cases regarding "home-made" herbal smoking blends. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  9. Is Blended e-Learning as Measured by an Achievement Test and Self-Assessment Better than Traditional Classroom Learning for Vocational High School Students?

    ERIC Educational Resources Information Center

    Chang, Chi-Cheng; Shu, Kuen-Ming; Liang, Chaoyun; Tseng, Ju-Shih; Hsu, Yu-Sheng

    2014-01-01

    The purpose of this study is to examine the effects of blended e-learning on electrical machinery performance (achievement test and self-assessment). Participants were two classes of 11th graders majoring in electrical engineering and taking the electrical machinery class at a vocational high school in Taiwan. The participants were randomly…

  10. Effect of the Blended Learning Environment and the Application of Virtual Class upon the Achievement and the Attitude against the Geography Course

    ERIC Educational Resources Information Center

    Dikmenli, Yurdal; Unaldi, Ulku Eser

    2013-01-01

    This study involves the elucidation of the effect of the virtual classroom application and blended learning medium upon the academic achievement of the students and their attitudes against the geography curse compared to the face to face expository (traditional) method. The study was carried out according to pre-test--post-test experimental design…

  11. A Pilot Study to Compare a Mushroom-Soy-Beef Burger to an All-Beef Burger in School Meals

    ERIC Educational Resources Information Center

    Summers, Amber C.; Smith, Paul; Ezike, Adaora; Frutchey, Robin; Fahle, Jenna; DeVries, Eva; Taylor, Jarrett; Cheskin, Lawrence J.

    2015-01-01

    Purpose/Objectives: The purpose of this study was to determine if mushroom blended recipes are an acceptable option for use in the school food program. The palatability and acceptance of mushroom-soy-beef blend burgers among school-aged children was tested. Methods: Students in grades 2 through 8 were invited to participate in a taste test.…

  12. A Comparison of Student Satisfaction and Value of Academic Community between Blended and Online Sections of a University-Level Educational Foundations Course

    ERIC Educational Resources Information Center

    Overbaugh, Richard C.; Nickel, Christine E.

    2011-01-01

    This pre-test/post-test study explores students' (n = 262) sense of academic community, including their perspectives of the value of academic community, plus course satisfaction and perceived learning in nearly identical blended and online sections of an educational foundations course. Students in both delivery modes were generally satisfied with…

  13. Nutrient composition, functional, and pasting properties of unripe cooking banana, pigeon pea, and sweetpotato flour blends.

    PubMed

    Ohizua, Ehimen R; Adeola, Abiodun A; Idowu, Micheal A; Sobukola, Olajide P; Afolabi, T Adeniyi; Ishola, Raphael O; Ayansina, Simeon O; Oyekale, Tolulope O; Falomo, Ayorinde

    2017-05-01

    This study investigated some quality attributes of unripe cooking banana (UBF), pigeon pea (PPF), and sweetpotato (SPF) flour blends. Simplex centroid mixture design was used to obtain 17 blends from the flours. The nutrient composition, color, and functional properties of the blends were evaluated using standard methods. Data were subjected to analysis of variance and treatment means were compared using Duncan's multiple range test at 5% probability level. There were significant ( p  < .05) differences in the nutrient composition, and functional and pasting properties of the blends. The crude protein, crude fiber, ash, foaming capacity, emulsion capacity, and least gelation capacity of the blends increased as the PPF level increased. The blends had Na/K ratio of <1.0. The dispersibility, bulk density, water, and oil absorption capacities of the blends increased as SPF and UBF increased. The peak, setback, and final viscosities increased as UBF and SPF inclusion increased,whereas pasting temperature and time increased as the PPF level increased. The L*, a*, and b* values of the flour blends which were significantly ( p  < .05) different ranged from 79.58 to 102.71, -0.15 to 2.79, and 13.82 to 23.69, respectively. Cooking banana-pigeon pea-sweetpotato flour blends are desirable for alleviating malnutrition in Nigeria and developing new food formulations.

  14. Thermal and mechanical properties of gamma-irradiated prevulcanized natural rubber latex/low nitrosamines latex blends

    NASA Astrophysics Data System (ADS)

    Ibrahim, Pairu; Daik, Rusli; Wan Zin, Wan Manshol

    2016-12-01

    Thermal and mechanical properties of blended radiation prevulcanized natural rubber latex (RVNRL) and low nitrosamines latex (LNL) were studied. RVNRL was blended with LNL at various composition ratios. From the tensile test, it was found that the optimum tensile value was attained at a total blending ratio of 70% RVNRL and 30% LNL. Latex blending with optimum tensile strength was then subjected to gamma irradiation at various doses with the presence and absence of methyl methacrylate (MMA) at 10 pphr. It was found that the gamma irradiation of latex blend with the presence of MMA could help increase further the tensile value. Composition of blending at a specific ratio and gamma irradiation at a specific dose has led to a significant improvement in the mechanical properties of the latex blend. The formation of grafting in the latex blend was characterized by Fourier transform infrared spectra (FTIR) spectroscopy and differential scanning calorimetry (DSC). FTIR spectroscopy confirmed that MMA could be grafted onto blended latex effectively under appropriate irradiation conditions. Two new peaks at 1731 and 1149 cm-1 were observed after irradiation, indicating the presence of an ester group from poly(methyl methacrylate) (PMMA), which was grafted onto rubber chains. This finding was proved by the presence of new Tg in DSC analysis. The increase in new Tg indicates the movement of grafting chains, which are tightly bound onto rubber chains.

  15. Synthesis and characterization of polyurethane-cellulose acetate blend membrane for chromium (VI) removal.

    PubMed

    Riaz, Tabinda; Ahmad, Adnan; Saleemi, Sidra; Adrees, Muhammad; Jamshed, Fahad; Hai, Abdul Moqeet; Jamil, Tahir

    2016-11-20

    Blended membranes of polyurethane and cellulose acetate were prepared, characterized and investigated for their performance. Various ratios of cellulose acetate were employed to prepare four different blend membranes. The characteristics of both pure and blend membranes were investigated and results were compared to distinguish their properties. Functional group analysis was carried out by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) of pure and blend samples. Contact angle measurement and water content were evaluated to determine the membrane hydrophilicity. Moreover, the membrane morphology was studied by scanning electron microscopy (SEM). The membrane permeation properties and ability to reject chromium (VI) ions were tested at various pH and pressure by utilizing different salt concentrations. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Fuel property effects on Navy aircraft fuel systems

    NASA Technical Reports Server (NTRS)

    Moses, C. A.

    1984-01-01

    Problems of ensuring compatibility of Navy aircraft with fuels that may be different than the fuels for which the equipment was designed and qualified are discussed. To avoid expensive requalification of all the engines and airframe fuel systems, methodologies to qualify future fuels by using bench-scale and component testing are being sought. Fuel blends with increasing JP5-type aromatic concentration were seen to produce less volume swell than an equivalent aromatic concentration in the reference fuel. Futhermore, blends with naphthenes, decalin, tetralin, and naphthalenes do not deviate significantly from the correlation line of aromatic blends, Similar results are found with tensile strenth and elongation. Other elastomers, sealants, and adhesives are also being tested.

  17. Rapid engine test to measure injector fouling in diesel engines using vegetable oil fuels

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Korus, R.A.; Jaiduk, J.; Peterson, C.L.

    1985-11-01

    Short engine tests were used to determine the rate of carbon deposition on direct injection diesel nozzles. Winter rape, high-oleic and high-linoleic safflower blends with 50% diesel were tested for carbon deposit and compared to that with D-2 Diesel Control Fuel. Deposits were greatest with the most unsaturated fuel, high-linoleic safflower, and least with winter rape. All vegetable oil blends developed power similar to diesel fueled engines with a 6 to 8% greater fuel consumption. 8 references.

  18. BLENDING ANALYSIS FOR RADIOACTIVE SALT WASTE PROCESSING FACILITY

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lee, S.

    2012-05-10

    Savannah River National Laboratory (SRNL) evaluated methods to mix and blend the contents of the blend tanks to ensure the contents are properly blended before they are transferred from the blend tank such as Tank 21 and Tank 24 to the Salt Waste Processing Facility (SWPF) feed tank. The tank contents consist of three forms: dissolved salt solution, other waste salt solutions, and sludge containing settled solids. This paper focuses on developing the computational model and estimating the operation time of submersible slurry pump when the tank contents are adequately blended prior to their transfer to the SWPF facility. Amore » three-dimensional computational fluid dynamics approach was taken by using the full scale configuration of SRS Type-IV tank, Tank 21H. Major solid obstructions such as the tank wall boundary, the transfer pump column, and three slurry pump housings including one active and two inactive pumps were included in the mixing performance model. Basic flow pattern results predicted by the computational model were benchmarked against the SRNL test results and literature data. Tank 21 is a waste tank that is used to prepare batches of salt feed for SWPF. The salt feed must be a homogeneous solution satisfying the acceptance criterion of the solids entrainment during transfer operation. The work scope described here consists of two modeling areas. They are the steady state flow pattern calculations before the addition of acid solution for tank blending operation and the transient mixing analysis during miscible liquid blending operation. The transient blending calculations were performed by using the 95% homogeneity criterion for the entire liquid domain of the tank. The initial conditions for the entire modeling domain were based on the steady-state flow pattern results with zero second phase concentration. The performance model was also benchmarked against the SRNL test results and literature data.« less

  19. Characterization of plastic blends made from mixed plastics waste of different sources.

    PubMed

    Turku, Irina; Kärki, Timo; Rinne, Kimmo; Puurtinen, Ari

    2017-02-01

    This paper studies the recyclability of construction and household plastic waste collected from local landfills. Samples were processed from mixed plastic waste by injection moulding. In addition, blends of pure plastics, polypropylene and polyethylene were processed as a reference set. Reference samples with known plastic ratio were used as the calibration set for quantitative analysis of plastic fractions in recycled blends. The samples were tested for the tensile properties; scanning electron microscope-energy-dispersive X-ray spectroscopy was used for elemental analysis of the blend surfaces and Fourier transform infrared (FTIR) analysis was used for the quantification of plastics contents.

  20. Certification of alternative aviation fuels and blend components

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wilson III, George R.; Edwards, Tim; Corporan, Edwin

    2013-01-15

    Aviation turbine engine fuel specifications are governed by ASTM International, formerly known as the American Society for Testing and Materials (ASTM) International, and the British Ministry of Defence (MOD). ASTM D1655 Standard Specification for Aviation Turbine Fuels and MOD Defence Standard 91-91 are the guiding specifications for this fuel throughout most of the world. Both of these documents rely heavily on the vast amount of experience in production and use of turbine engine fuels from conventional sources, such as crude oil, natural gas condensates, heavy oil, shale oil, and oil sands. Turbine engine fuel derived from these resources and meetingmore » the above specifications has properties that are generally considered acceptable for fuels to be used in turbine engines. Alternative and synthetic fuel components are approved for use to blend with conventional turbine engine fuels after considerable testing. ASTM has established a specification for fuels containing synthesized hydrocarbons under D7566, and the MOD has included additional requirements for fuels containing synthetic components under Annex D of DS91-91. New turbine engine fuel additives and blend components need to be evaluated using ASTM D4054, Standard Practice for Qualification and Approval of New Aviation Turbine Fuels and Fuel Additives. This paper discusses these specifications and testing requirements in light of recent literature claiming that some biomass-derived blend components, which have been used to blend in conventional aviation fuel, meet the requirements for aviation turbine fuels as specified by ASTM and the MOD. The 'Table 1' requirements listed in both D1655 and DS91-91 are predicated on the assumption that the feedstocks used to make fuels meeting these requirements are from approved sources. Recent papers have implied that commercial jet fuel can be blended with renewable components that are not hydrocarbons (such as fatty acid methyl esters). These are not allowed blend components for turbine engine fuels as discussed in this paper.« less

  1. Manufacturing and characterization of encapsulated microfibers with different molecular weight poly(ε-caprolactone) (PCL) resins using a melt electrospinning technique

    NASA Astrophysics Data System (ADS)

    Lee, Jason K.; Ko, Junghyuk; Jun, Martin B. G.; Lee, Patrick C.

    2016-02-01

    Encapsulated structures of poly(ε-caprolactone) microfibers were successfully fabricated through two distinct melt electrospinning methods: melt coaxial and melt-blending electrospinning methods. Both methods resulted in encapsulated microfibers, but the resultant microfibers had different morphologies. Melt coaxial electrospinning formed a dual, semi-concentric structure, whereas melt-blending electrospinning resulted in an islands-in-a-sea fiber structure (i.e. a multiple-core structure). The encapsulated microfibers were produced using a custom-designed melt coaxial electrospinning device and the microfibers were characterized using a scanning electron microscope. To analyze the properties of the melt blended encapsulated fibers and coaxial fibers, the microfiber mesh specimens were collected. The mechanical properties of each microfiber mesh were analyzed through a tensile test. The coaxial microfiber meshes were post processed with a femtosecond laser machine to create dog-bone shaped tensile test specimens, while the melt blended microfiber meshes were kept as-fabricated. The tensile experiments undertaken with coaxial microfiber specimens resulted in an increase in tensile strength compared to 10 k and 45 k monolayer specimens. However, melt blended microfiber meshes did not result in an increase in tensile strength. The melt blended microfiber mesh results indicate that by using greater amounts of 45 k PCL resin within the microstructure, the resulting fibers obtain a higher tensile strength.

  2. Self-repairing systems based on ionomers and epoxidized natural rubber blends.

    PubMed

    Rahman, Md Arifur; Penco, Maurizio; Peroni, Isabella; Ramorino, Giorgio; Grande, Antonio Mattia; Di Landro, Luca

    2011-12-01

    The development of materials with the ability of intrinsic self-repairing after damage in a fashion resembling that of living tissues has important scientific and technological implications, particularly in relation to cost-effective approaches toward damage management of materials. Natural rubbers with epoxy functional groups in the macromolecular chain (ENR) and ethylene-methacrylic acid ionomers having acid groups partially neutralized with metal ions possess self-repairing behavior following high energy impacts. This research investigates the self-repairing behavior of both ENR and ionomers during ballistic puncture test on the basis of their thermal and mechanical properties. Heterogeneous blending of ionomers and ENR have also been used here as a strategy to tune the thermal and mechanical properties of the materials. Interestingly, blends of sodium ion containing ionomer exhibit complete self-repairing behavior, whereas blends of zinc ion containing ionomer show limited mending. The chemical structure studied by FTIR and thermal analysis shows that both ion content of ionomer and functionality of ENR have significant influence on the self-repairing behavior of blends. The mobility of rubbery phases along with its interaction to ionomer phase in the blends significantly changes the mending capability of materials. The healing behavior of the materials has been discussed on the basis of their thermal, mechanical, and rheological tests for each materials. © 2011 American Chemical Society

  3. Unique synergism in flame retardancy in ABS based composites through blending PVDF and halloysite nanotubes

    NASA Astrophysics Data System (ADS)

    Remanan, Sanjay; Sharma, Maya; Jayashree, Priyadarshini; Parameswaranpillai, Jyotishkumar; Fabian, Thomas; Shih, Julie; Shankarappa, Prasad; Nuggehalli, Bharath; Bose, Suryasarathi

    2017-06-01

    This study demonstrates flame retardant materials designed using bi-phasic polymer blends of acrylonitrile butadiene styrene (ABS) and polyvinylidene fluoride (PVDF) containing halloysite nanotubes (HNTs) and Cloisite 30B nanoclay. The prepared blends with and without nanoparticles were extensively characterized. The nanoparticles were added in different weight concentrations to improve the flame retardancy. It was observed that prepared ABS/PVDF blends showed better flame retardancy than ABS based composites. The flame resistance was further improved by the addition of nanoparticles in the blends. The microscale combustion calorimetry (MCC) test showed better flame resistance in ABS/PVDF blends filled with 5 wt% HNTs than other composites. The total heat release of ABS/PVDF blend filled with 5 wt% HNTs decreased by 31% and also the heat of combustion decreased by 26% as compared to neat ABS. When compared with nanoparticles, the addition of PVDF reduced the peak heat release rate (PHRR) and increased the char residue more effectively. A synergistic improvement was observed from both PVDF and HNTs on the flame resistance properties.

  4. Miscible blends of biobased poly(lactide) with poly(methyl methacrylate): Effects of chopped glass fiber incorporation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Cousins, Dylan S.; Lowe, Corinne; Swan, Dana

    Poly(lactide) (PLA) and poly(methyl methacrylate) (PMMA) are melt compounded with chopped glass fiber using laboratory scale twin-screw extrusion. Physical properties are examined using differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), tensile testing, impact testing, X-ray computed tomography (CT) scanning, and field emission scanning electron microscopy (FE-SEM). Molecular weight is determined using gel permeation chromatography (GPC). Miscibility of the blends is implied by the presence of a single glass transition temperature and homogeneous morphology. PLA/PMMA blends tend to show positive deviations from a simple linear mixing rule in their mechanical properties (e.g., tensile toughness, modulus, andmore » stress at break). The addition of 40 wt % glass fiber to the system dramatically increases physical properties. Across all blend compositions, the tensile modulus increases from roughly 3 GPa to roughly 10 GPa. Estimated heat distortion temperatures (HDTs) are also greatly enhanced; the pure PLA sample HDT increases from 75 degrees C to 135 degrees C. Fiber filled polymer blends represent a sustainable class of earth abundant materials which should prove useful across a range of applications.« less

  5. Modification of bone graft by blending with lecithin to improve hydrophilicity and biocompatibility.

    PubMed

    Wang, Y; Cui, F Z; Jiao, Y P; Hu, K; Fan, D D

    2008-03-01

    Lecithin was blended to improve the hydrophilicity and biocompatibility of bone graft containing poly(l-lactic acid) (PLLA). Solution blending and freeze drying were used to fabricate symmetrical scaffolds containing different percentages of lecithin (lecithin: PLLA = 0, 5, 10 wt%). Scanning electron microscopy showed that the scaffolds maintained the three-dimensional porous structure. A water uptake experiment proved the significant improvement of hydrophilicity of the blend scaffold. With the addition of lecithin, the compressive strength and compressive modulus decreased. When the weight ratio of lecithin to PLLA was up to 10%, the compressive strength was still more than the lower limit of natural cancellous bone. To test the biocompatibility of the scaffolds, cell culture in vitro and subcutaneous implantation in vivo were performed. MC3T3-E1 preosteoblastic cells were cultured on the scaffolds for 7 days. Methylthiazol tetrazolium assay and laser scanning confocal microscopy were used to exhibit proliferation and morphology of the cells. The subcutaneous implantation in rats tested inflammatory response to the scaffolds. The results proved the better biocompatibility and milder inflammatory reactions of the blend scaffold (lecithin: PLLA = 5%) compared with the scaffold without lecithin. The modified scaffold containing lecithin is promising for bone tissue engineering.

  6. REDUCING POWER PRODUCTION COSTS BY UTILIZING PETROLEUM COKE

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    1998-09-01

    A Powder River Basin subbituminous coal from the North Antelope mine and a petroleum shot coke were received from Northern States Power Company (NSP) for testing the effects of parent fuel properties on coal-coke blend grindability and evaluating the utility of petroleum coke blending as a strategy for improving electrostatic precipitator (ESP) particulate collection efficiency. Petroleum cokes are generally harder than coals, as indicated by Hardgrove grindability tests. Therefore, the weaker coal component may concentrate in the finer size fractions during the pulverizing of coal-coke blends. The possibility of a coal-coke size fractionation effect is being investigated because it maymore » adversely affect combustion performance. Although the blending of petroleum coke with coal may adversely affect combustion performance, it may enhance ESP particulate collection efficiency. Petroleum cokes contain much higher concentrations of V relative to coals. Consequently, coke blending can significantly increase the V content of fly ash resulting from coal-coke combustion. Pentavalent vanadium oxide (V{sub 2}O{sub 5}) is a known catalyst for transforming gaseous sulfur dioxide (SO{sub 2}[g]) to gaseous sulfur trioxide (SO{sub 3}[g]). The presence of SO{sub 3}(g) strongly affects fly ash resistivity and, thus, ESP performance.« less

  7. Wind tunnel behavioural response and field trapping of the blowfly Calliphora vicina.

    PubMed

    Aak, A; Knudsen, G K; Soleng, A

    2010-09-01

    The attraction of the blowfly Calliphora vicina Robineau-Desvoidy, 1830 (Diptera: Calliphoridae) to single synthetic compounds, blends and authentic odours was investigated in a wind tunnel. A total of 1850 C. vicina (1750 females and 100 males) were tested. A comparison of male and female responses showed significant differences in attraction between the sexes. Females were more attracted than males to liver odour. The attraction of females lay in the ranges of 0-22% for single compounds, 26-64% for synthetic blends and 58-88% for authentic odours. Dimethyl trisulphide was the most attractive single compound. Significant improvement in attraction was achieved with blends and a three-component lure, consisting of dimethyl trisulphide, mercaptoethanol and o-cresol, was found to be the best solution for field trapping of C. vicina. Authentic odours from dead fish and mice were significantly more attractive than liver and the three-component blend, and the blend and liver were similarly effective as attractants. Field tests support the results of the wind tunnel study and a high number of C. vicina were caught in funnel traps. Overall, 99.1% of the specimens caught were females.

  8. Preparation and characterization of jackfruit seed starch/poly (vinyl alcohol) (PVA) blend film

    NASA Astrophysics Data System (ADS)

    Sarifuddin, N.; Shahrim, N. A.; Rani, N. N. S. A.; Zaki, H. H. M.; Azhar, A. Z. A.

    2018-01-01

    From the environmental point of view, biodegradable materials have been rapidly developed in the past years. PVA is one of the biodegradable synthetic polymers commonly used, but its degradation rate is slow. As an alternative to reduce plastic waste and accelerate the degradation process, PVA frequently blended with other natural polymers to improve its biodegradability. The natural polymer such as starch has high potential in enhancing PVA biodegradability by blending both components. The usage of starch extracted from agriculture wastes such as jackfruit seed is quite promising. In this study, jackfruit seed starch (JFSS)/poly (vinyl alcohol) (PVA) blend films were prepared using the solution casting method. The effect of starch content on the mechanical (tensile strength and elongation to break %) and physical properties of the tested films were investigated. The optimum tensile strength was obtained at 10.45 MPa when 4 wt. % of starch added to the blend. But, decreasing trend of tensile strength was found upon increasing the amount of starch beyond 4 wt. % in starch/PVA blend films. Nevertheless, elongation at break decreases with the increase in starch content. The mechanical properties of the blend films are supported by the Field Emission Scanning Electron Microscopy (FESEM), in which the native JFSS granules are wetted by PVA continuous phase with good dispersion and less agglomeration. The incorporation of JFSS in PVA has also resulted in the appearance of hydrogen bond peak, which evidenced by Fourier Transform Infrared (FTIR). Additionally, the biodegradation rate of JFSS/PVA was evaluated through soil burial test.

  9. "Flipping" the introductory clerkship in radiology: impact on medical student performance and perceptions.

    PubMed

    Belfi, Lily M; Bartolotta, Roger J; Giambrone, Ashley E; Davi, Caryn; Min, Robert J

    2015-06-01

    Among methods of "blended learning" (ie, combining online modules with in-class instruction), the "flipped classroom" involves student preclass review of material while reserving class time for interactive knowledge application. We integrated blended learning methodology in a "flipped" introductory clerkship in radiology, and assessed the impact of this approach on the student educational experience (performance and perception). In preparation for the "flipped clerkship," radiology faculty and residents created e-learning modules that were uploaded to an open-source website. The clerkship's 101 rising third-year medical students were exposed to different teaching methods during the course, such as blended learning, traditional lecture learning, and independent learning. Students completed precourse and postcourse knowledge assessments and surveys. Student knowledge improved overall as a result of taking the course. Blended learning achieved greater pretest to post-test improvement of high statistical significance (P value, .0060) compared to lecture learning alone. Blended learning also achieved greater pretest to post-test improvement of borderline statistical significance (P value, .0855) in comparison to independent learning alone. The difference in effectiveness of independent learning versus lecture learning was not statistically significant (P value, .2730). Student perceptions of the online modules used in blended learning portions of the course were very positive. They specifically enjoyed the self-paced interactivity and the ability to return to the modules in the future. Blended learning can be successfully applied to the introductory clerkship in radiology. This teaching method offers educators an innovative and efficient approach to medical student education in radiology. Copyright © 2015 AUR. Published by Elsevier Inc. All rights reserved.

  10. E-beam sterilizable thermoplastics elastomers for healthcare devices: Mechanical, morphology, and in vivo studies.

    PubMed

    Balaji, Ananad Bellam; Ratnam, Chantara Thevy; Khalid, Mohammad; Walvekar, Rashmi

    2018-03-01

    The effect of electron beam radiation on ethylene-propylene diene terpolymer/polypropylene blends is studied as an attempt to develop radiation sterilizable polypropylene/ethylene-propylene diene terpolymer blends suitable for medical devices. The polypropylene/ethylene-propylene diene terpolymer blends with mixing ratios of 80/20, 50/50, 20/80 were prepared in an internal mixer at 165°C and a rotor speed of 50 rpm/min followed by compression molding. The blends and the individual components were radiated using 3.0 MeV electron beam accelerator at doses ranging from 0 to 100 kGy in air and room temperature. All the samples were tested for tensile strength, elongation at break, hardness, impact strength, and morphological properties. After exposing to 25 and 100 kGy radiation doses, 50% PP blend was selected for in vivo studies. Results revealed that radiation-induced crosslinking is dominating in EPDM dominant blends, while radiation-induced degradation is prevailing in PP dominant blends. The 20% PP blend was found to be most compatible for 20-60 kGy radiation sterilization. The retention in impact strength with enhanced tensile strength of 20% PP blend at 20-60 kGy believed to be associated with increased compatibility between PP and EPDM along with the radiation-induced crosslinking. The scanning electron micrographs of the fracture surfaces of the PP/EPDM blends showed evidences consistent with the above contentation. The in vivo studies provide an instinct that the radiated blends are safe to be used for healthcare devices.

  11. Evaluation of novophalt as an additive in asphalt.

    DOT National Transportation Integrated Search

    1991-01-01

    Novophalt, which is an ethylene vinyl acetate polymer, was used as an asphalt additive in a test section in an attempt to determine whether it is useful in the prevention of rutting. A special blending unit was required to blend the asphalt cement an...

  12. Life cycle assessment of PC blend 2 aircraft radome depainter. Final report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Thomas, R.; Franklin, W.E.

    1996-09-01

    This report describes a multi-year effort to test and evaluate a solvent blend alternative for methyl ethyl ketone (MEK) in aircraft radome depainting operations. The study was conducted at the Oklahoma City Air Logistics Center (OC-ALC) at Tinker Air Force Base (TAFB). TAFB currently uses MEK to depaint B-52 and KC-135 aircraft randomes in a ventilated booth. Because MEK is highly volatile, many gallons vaporize in the atmosphere during each depainting session. Supported by SERDP and EPA`s WREAPS program, this study began with a preliminary testing by Huntsman Chemical Company to determine the optimal formulation of the chemical stripper. Wemore » then conducted a demonstration of a formulation designated PC Blend 2, which was shown to have performance characteristics comparable to MEK. This report expands upon the completed technology evaluation through a life cycle evaluation of PC Blend 2 to determine the environmental, energy and economic impacts of each chemical and the formulation.« less

  13. Toxicity of tomato red, a popular food dye blend on male albino mice.

    PubMed

    Sharma, Shipra; Goyal, Rajendra P; Chakravarty, Geetanjali; Sharma, Anjali

    2008-06-01

    Colour in food is an integral part of our culture and is also indispensable to the modern day consumer. During the past several decades, the technology of food processing has changed dramatically and the growth in the use of synthetic food colours as an individual dye or in the form of blends has increased enormously. In the present investigation, an attempt has been made to evaluate the toxic effects of a commonly used dye blend, tomato red on male Swiss albino mice. The mice were treated orally with 2 and 6g/kg body weight/day for 42 days. The present study revealed an increase in the body weight and liver weight. However, a decrease was recorded in the weights of kidneys and testes. Histopathological study revealed severe degenerative changes in the liver, kidney and testes. In conclusion, the use of the dye blend in various food items has adverse effect on the vital organs.

  14. Polyethersulfone - barium chloride blend ultrafiltration membranes for dye removal studies

    NASA Astrophysics Data System (ADS)

    Rambabu, K.; Srivatsan, N.; Gurumoorthy, Anand V. P.

    2017-11-01

    A series of Polyethersulfone (PES) - barium chloride (BaCl2) blend ultra filtration membrane was developed by varying the BaCl2 concentration in the dope solution. Prepared membranes were subjected to membrane characterization and their performance was studied through dye rejection tests. Morphological studies through SEM and AFM showed that the composite membranes exhibited differences in morphologies, porosities and properties due to the BaCl2 addition as compared with pristine PES membrane. Addition of the inorganic modifier enhanced the hydrophilicity and water permeability of the blend membrane system. Polymer enhanced ultrafiltration of dye solutions showed that the proposed blend system had better performance in terms of flux and rejection efficiency than the pure polymer membrane. The performance of the 2 wt% BaCl2 blend membrane was more promising for application to real time dye wastewater studies.

  15. Comparative analysis of emission characteristics and noise test of an I.C. engine using different biodiesel blends

    NASA Astrophysics Data System (ADS)

    Hossain, Md. Alamgir; Rahman, Fariha; Mamun, Maliha; Naznin, Sadia; Rashid, Adib Bin

    2017-12-01

    Biodiesel is a captivating renewable resource providing the potential to reduce particulate emissions in compressionignition engines. A comparative study is conducted to evaluate the effects of using biodiesel on exhaust emissions. Exhaust smokiness, noise and exhaust regulated gas emissions such as carbon di oxides, carbon monoxide and oxygen are measured. It is observed that methanol-biodiesel blends (mustard oil, palm oil) cause reduction of emissions remarkably. Most of the harmful pollutants in the exhaust are reduced significantly with the use of methanol blended fuels. Reduction in CO emission is more with mustard oil blend compared to palm oil blend. Comparatively clean smoke is observed with biodiesel than diesel. It is also observed that, there is a decrease of noise while performing with biodiesel blends which is around 78 dB whereas noise caused by diesel is 80 dB. Biodiesel, more importantly mustard oil is a clean burning fuel that does not contribute to the net increase of carbon dioxide.

  16. Effect of EPDM-g-MAH on properties of HDPE/OBC blends

    NASA Astrophysics Data System (ADS)

    Li, M.; Yu, L. Y.; Li, P. F.; Bin, Y. H.; Zhang, H. J.

    2017-04-01

    In this paper, we take the HDPE as the matrix material, OBC as the toughening material, and EDPM-g-MAH as the compatibility agent, HDPE/OBC/EPDM-g-MAH blends were prepared by high speed mixing, melt extrusion, injection molding and so on. The effects of OBC and EPDM-g-MAH on mechanical properties, crystalline properties, fracture surface structure and rheological properties of HDPE were analyzed by universal tensile tester, melt mass flow rate test machine, DSC and SEM. Experimental results show that: with the addition of EPDM-g-MAH, the notched impact strength of the blends increased first and then decreased; HDPE/OBC blend containing 4% EPDM-g-MAH, OBC dispersion in the matrix is more uniform, particle size is significantly refined, melt flow has some improvement, Compared with HDPE/OBC blend materials, notched impact strength and elongation at break increased by 41.07% and 107.28% respectively, the toughness of the blend was greatly improved.

  17. Preparation and Effect of Gamma Radiation on The Properties and Biodegradability of Poly(Styrene/Starch) Blends

    NASA Astrophysics Data System (ADS)

    Ali, H. E.; Abdel Ghaffar, A. M.

    2017-01-01

    Biodegradable blends based on Poly(styrene/starch) Poly(Sty/Starch) were prepared by the casting method using different contents of starch in the range of 0-20 wt% aiming at preparing disposable packaging materials. The prepared bio-blends were Characterized by Fourier transform infrared (FTIR), swelling behavior, mechanical properties, thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). It was found that the swelling behavior slightly increased with increasing starch content and not exceeding 7.5%. The results showed that by increasing irradiation dose up to 5 kGy, the mechanical properties of the prepared PSty/10 wt% Starch blend film modified than other blend films, and hence it is selected. Also the water resistant increased, by irradiation of the selected PSty/10 wt% Starch blend film. The intermolecular hydrogen bonding interaction between Starch and PSty of the PSty/10 wt% Starch blend film promote a more homogenous blend film as shown in scanning electron microscopy (SEM). The prepared Poly(Sty/Starch) blends with different compositions and the selected irradiated PSty/10 wt% Starch blend were subjected to biodegradation in soil burial tests for 6 months using two different types of soils; agricultural and desert soils, then analyzed gravimetrically and by scanning electron microscopy (SEM). The results suggested that there is a possibility of using irradiated PSty/10 wt% Starch at a dose of 5 kGy as a potential candidate for packaging material.

  18. Influence of Blended Cements with Calcareous Fly Ash on Chloride Ion Migration and Carbonation Resistance of Concrete for Durable Structures.

    PubMed

    Glinicki, Michał A; Jóźwiak-Niedźwiedzka, Daria; Gibas, Karolina; Dąbrowski, Mariusz

    2016-01-02

    The objective of this paper is to examine the possible use of new blended cements containing calcareous fly ash in structural concrete, potentially adequate for structural elements of nuclear power plants. The investigation included five new cements made with different contents of non-clinker constituents: calcareous fly ash, siliceous fly ash, ground granulated blastfurnace slag, and a reference cement-ordinary Portland cement. The influence of innovative cements on the resistance of concrete to chloride and carbonation exposure was studied. Additionally, an evaluation of the microstructure was performed using optical microscopy on concrete thin sections. Test results revealed a substantial improvement of the resistance to chloride ion penetration into concrete containing blended cements. The resistance was higher for increased clinker replacement levels and increased with curing time. However, concrete made with blended cements exhibited higher depth of carbonation than the Portland cement concrete, except the Portland-fly ash cement with 14.3% of calcareous fly ash. The thin sections analysis confirmed the values of the carbonation depth obtained from the phenolphthalein test. Test results indicate the possible range of application for new cements containing calcareous fly ash.

  19. Influence of Blended Cements with Calcareous Fly Ash on Chloride Ion Migration and Carbonation Resistance of Concrete for Durable Structures

    PubMed Central

    Glinicki, Michał A.; Jóźwiak-Niedźwiedzka, Daria; Gibas, Karolina; Dąbrowski, Mariusz

    2016-01-01

    The objective of this paper is to examine the possible use of new blended cements containing calcareous fly ash in structural concrete, potentially adequate for structural elements of nuclear power plants. The investigation included five new cements made with different contents of non-clinker constituents: calcareous fly ash, siliceous fly ash, ground granulated blastfurnace slag, and a reference cement—ordinary Portland cement. The influence of innovative cements on the resistance of concrete to chloride and carbonation exposure was studied. Additionally, an evaluation of the microstructure was performed using optical microscopy on concrete thin sections. Test results revealed a substantial improvement of the resistance to chloride ion penetration into concrete containing blended cements. The resistance was higher for increased clinker replacement levels and increased with curing time. However, concrete made with blended cements exhibited higher depth of carbonation than the Portland cement concrete, except the Portland-fly ash cement with 14.3% of calcareous fly ash. The thin sections analysis confirmed the values of the carbonation depth obtained from the phenolphthalein test. Test results indicate the possible range of application for new cements containing calcareous fly ash. PMID:28787821

  20. Friction characteristics of 20 x 4.4, type 7, aircraft tires constructed with different tread rubber compounds

    NASA Technical Reports Server (NTRS)

    Dreher, R. C.; Yager, T. J.

    1976-01-01

    A test program was conducted at the Langley aircraft landing loads and traction facility to evaluate the friction characteristics of 20 x 4.4, type, aircraft tires constructed with experimental cut-resistant, tread rubber compounds. These compounds consisted of different blends of natural rubber (NR) and an alfin catalyzed styrene-butadiene copolymer rubber (SBR). One tire having a blend of 30 SBR and 70 NR and another having a blend of 60 SBR and 40 NR in the tread were tested together with a standard production tire with no SBR content in the tread rubber. The results of this investigation indicated that the test tires constructed with the special cut-resistant tread rubber compositions did not suffer any significant degradation in tire friction capability when compared with the standard tire. In general, tire friction capability decreased with increasing speed and surface wetness condition. As yaw angle increased, tire braking capability decreased while tire cornering capability increased. Tread-wear data based on number of brake cycles, however, suggested that the tires with alfin SBR blends experienced significantly greater wear than the standard production tire.

  1. The influence of the biofuel blends on the energetic and ecological performances of the Diesel engine

    NASA Astrophysics Data System (ADS)

    Benea, B. C.

    2016-08-01

    This study presents the influence of the diesel fuel blended with biodiesel fuel obtained from sunflower oil, corn oil and peanut oil on the energetic performances, combustion process and pollutant emissions. This research was done virtually and experimentally. In this study pure diesel fuel and two concentrations (6% and 10%) of blends with biofuels were used for experimentally tests on a Renault K9K diesel engine. Five parameters were observed during experimental tests: engine power, fuel consumption, cylinder pressure, and the amount of CO and NOx emissions. The same five parameters were simulated using AVL Boost program. The variations of effective power and maximal cylinder pressure are caused due to the lower calorific value of the tested fuels. Better oxidation of the biofuels induces a better combustion in cylinder and less CO and NOx emissions. The CO emissions are either influence by the lower carbon content of biofuels. The results of this study sustain that using 6% and 10% of blended biofuels with diesel fuel decrease the pollutant emissions of the diesel engine. Deviations between experimental and the simulation results confirm the validity of the mathematical model adopted for the simulation.

  2. Effects of Blended-Cement Paste Chemical Composition Changes on Some Strength Gains of Blended-Mortars

    PubMed Central

    Kirgiz, Mehmet Serkan

    2014-01-01

    Effects of chemical compositions changes of blended-cement pastes (BCPCCC) on some strength gains of blended cement mortars (BCMSG) were monitored in order to gain a better understanding for developments of hydration and strength of blended cements. Blended cements (BC) were prepared by blending of 5% gypsum and 6%, 20%, 21%, and 35% marble powder (MP) or 6%, 20%, 21%, and 35% brick powder (BP) for CEMI42.5N cement clinker and grinding these portions in ball mill at 30 (min). Pastes and mortars, containing the MP-BC and the BP-BC and the reference cement (RC) and tap water and standard mortar sand, were also mixed and they were cured within water until testing. Experiments included chemical compositions of pastes and compressive strengths (CS) and flexural strengths (FS) of mortars were determined at 7th-day, 28th-day, and 90th-day according to TS EN 196-2 and TS EN 196-1 present standards. Experimental results indicated that ups and downs of silica oxide (SiO2), sodium oxide (Na2O), and alkali at MP-BCPCC and continuously rising movement of silica oxide (SiO2) at BP-BCPCC positively influenced CS and FS of blended cement mortars (BCM) in comparison with reference mortars (RM) at whole cure days as MP up to 6% or BP up to 35% was blended for cement. PMID:24587737

  3. Investigation of compression behavior of PE/EVA foam injection molded parts

    NASA Astrophysics Data System (ADS)

    Spina, Roberto

    2017-10-01

    The main objective of the presented work is to evaluate the compression behavior of a polymeric foam blend by using a robust framework for the testing sequence of foaming injection molded parts, with the aim of establishing a standard testing cycle for the evaluation of new matrix material. The research purpose is to assess parameters influencing compression behavior and give useful suggestions for the implementation of a finite element analysis. The polymeric blend consisted of a mixture of low density polyethylenes (LDPEs), a high-density polyethylene (HDPE), an ethylene-vinyl acetate (EVA) and an azodicarbonamide (ADC). The thermal, rheological and compression properties of the blend are fully described, as well as the injection molding process for two specimen types.

  4. Regulated emissions from biodiesel fuels from on/off-road applications

    NASA Astrophysics Data System (ADS)

    Durbin, Thomas D.; Cocker, David R.; Sawant, Aniket A.; Johnson, Kent; Miller, J. Wayne; Holden, Bruce B.; Helgeson, Norman L.; Jack, Jason A.

    This research is one of the largest studies of biodiesel in both on-road and off-road uses. The testing was conducted for the military and encompassed a wide range of application types including two medium-duty trucks, two Humvees, a heavy heavy-duty diesel truck, a bus, two stationary backup generators (BUGs), a forklift, and an airport tow vehicle. The full range of fuels tested included a California ultra-low sulfur diesel (ULSD) fuel, different blend ratios of two different yellow-grease biodiesels and one soy-based biodiesel, JP-8, and yellow-grease biodiesel blends with two different NO x reduction additives. The B20-YGA, B20-YGB, and B20-Soy did not show trends relative to ULSD that were consistent over all applications tested. Higher biodiesel blends were tested on only one vehicle, but showed a tendency for higher total hydrocarbons (THC) and carbon monoxide (CO) emissions and lower particulate matter (PM) emissions. The JP-8 showed increases in THC and CO relative to the ULSD.

  5. Integrated Experimental and Numerical Research on the Aerodynamics of Unsteady Moving Aircraft

    DTIC Science & Technology

    2007-06-01

    blended wing body configuration were tested in different modes of oscillatory motions roll, pitch and yaw as well as delta wing geometries like X-31...airplane configurations (e.g. wide body, green aircraft, blended wing body) the approach up to now using semi-empirical methods as standard...cross section wing. In order to evaluate the influence of individual components of the tested airplane configuration, such as winglets , vertical or

  6. [Blended-learning in psychosomatics and psychotherapy - Increasing the satisfaction and knowledge of students with a web-based e-learning tool].

    PubMed

    Ferber, Julia; Schneider, Gudrun; Havlik, Linda; Heuft, Gereon; Friederichs, Hendrik; Schrewe, Franz-Bernhard; Schulz-Steinel, Andrea; Burgmer, Markus

    2014-01-01

    To improve the synergy of established methods of teaching, the Department of Psychosomatics and Psychotherapy, University Hospital Münster, developed a web-based elearning tool using video clips of standardized patients. The effect of this blended-learning approach was evaluated. A multiple-choice test was performed by a naive (without the e-learning tool) and an experimental (with the tool) cohort of medical students to test the groups' expertise in psychosomatics. In addition, participants' satisfaction with the new tool was evaluated (numeric rating scale of 0-10). The experimental cohort was more satisfied with the curriculum and more interested in psychosomatics. Furthermore, the experimental cohort scored significantly better in the multiple-choice test. The new tool proved to be an important addition to the classical curriculum as a blended-learning approach which improves students' satisfaction and knowledge in psychosomatics.

  7. Formulation and evaluation of C-Ether fluids as lubricants useful to 260 C. [air breathing engines

    NASA Technical Reports Server (NTRS)

    Clark, F. S.; Miller, D. R.

    1980-01-01

    Three base stocks were evaluated in bench and bearing tests to determine their suitability for use at bulk oil temperatures (BOT) from -40 C to +260 C. A polyol ester gave good bearing tests at a bulk temperature of 218 C, but only a partially successful run at 274 C. These results bracket the fluid's maximum operating temperature between these values. An extensive screening program selected lubrication additives for a C-ether (modified polyphenyl ether) base stock. One formulation lubricated a bearing for 111 hours at 274 C (BOT), but this fluid gave many deposit related problems. Other C-ether blends produced cage wear or fatigue failures. Studies of a third fluid, a C-ether/disiloxane blend, consisted of bench oxidation and lubrication tests. These showed that some additives react differently in the blend than in pure C-ethers.

  8. Thermal Stability Testing of a Fischer-Tropsch Fuel and Various Blends with Jet A

    NASA Technical Reports Server (NTRS)

    Klettlinger, Jennifer Suder; Surgenor, Angela; Yen, Chia

    2010-01-01

    Fischer-Tropsch (F-T) jet fuel composition differs from petroleum-based, conventional commercial jet fuel because of differences in feedstock and production methodology. Fischer-Tropsch fuel typically has a lower aromatic and sulfur content and consists primarily of iso and normal parafins. The ASTM D3241 specification for Jet Fuel Thermal Oxidation Test (JFTOT) break point testing method was used to test the breakpoint of a baseline conventional Jet A, a commercial grade F-T jet fuel, and various blends of this F-T fuel in Jet A. The testing completed in this report was supported by the NASA Fundamental Aeronautics Subsonics Fixed Wing Project.

  9. Microbial Degradation Behavior in Seawater of Polyester Blends Containing Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx)

    PubMed Central

    Sashiwa, Hitoshi; Fukuda, Ryuji; Okura, Tetsuo; Sato, Shunsuke; Nakayama, Atsuyoshi

    2018-01-01

    The microbial degradation behavior of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) and its compound with several polyesters such as poly(butylene adipate-co-telephtharate) (PBAT), poly(butylene succinate) (PBS), and polylactic acid (PLA) in seawater was tested by a biological oxygen demand (BOD) method. PHBHHx showed excellent biodegradation in seawater in this study. In addition, the biodegradation rate of several blends was much influenced by the weight ratio of PHBHHx in their blends and decreased in accordance with the decrement of PHBHHX ratio. The surface morphology of the sheet was important factor for controlling the biodegradation rate of PHBHHx-containing blends in seawater. PMID:29342118

  10. 40 CFR Table 5 to Subpart Qqqq of... - Default Organic HAP Mass Fraction for Solvents and Solvent Blends

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... the following table for solvent blends for which you do not have test data or manufacturer's... spirits 64742-89-6 0.15 Toluene. 14. Low aromatic white spirit 64742-82-1 0 None. 15. Mineral spirits...

  11. 40 CFR Table 3 to Subpart Nnnn of... - Default Organic HAP Mass Fraction for Solvents and Solvent Blends

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... the following table for solvent blends for which you do not have test data or manufacturer's... spirits 64742-89-6 0.15 Toluene. 14. Low aromatic white spirit 64742-82-1 0 None. 15. Mineral spirits...

  12. 40 CFR Table 5 to Subpart Qqqq of... - Default Organic HAP Mass Fraction for Solvents and Solvent Blends

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... the following table for solvent blends for which you do not have test data or manufacturer's... spirits 64742-89-6 0.15 Toluene. 14. Low aromatic white spirit 64742-82-1 0 None. 15. Mineral spirits...

  13. 40 CFR Table 3 to Subpart Nnnn of... - Default Organic HAP Mass Fraction for Solvents and Solvent Blends

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... the following table for solvent blends for which you do not have test data or manufacturer's... spirits 64742-89-6 0.15 Toluene. 14. Low aromatic white spirit 64742-82-1 0 None. 15. Mineral spirits...

  14. Microstructure and molecular interaction in glycerol plasticized chitosan/poly(vinyl alcohol) blending films

    USDA-ARS?s Scientific Manuscript database

    Poly (vinyl alcohol) (PVA)/chitosan (CS) blended films plasticized by glycerol were investigated using mechanical testing, atomic force microscopy (AFM), differential scanning calorimetry (DSC) and FTIR spectroscopy, with primary emphasis on the effects of the glycerol content and the molecular weig...

  15. Predicting the composition of red wine blends using an array of multicomponent Peptide-based sensors.

    PubMed

    Ghanem, Eman; Hopfer, Helene; Navarro, Andrea; Ritzer, Maxwell S; Mahmood, Lina; Fredell, Morgan; Cubley, Ashley; Bolen, Jessica; Fattah, Rabia; Teasdale, Katherine; Lieu, Linh; Chua, Tedmund; Marini, Federico; Heymann, Hildegarde; Anslyn, Eric V

    2015-05-20

    Differential sensing using synthetic receptors as mimics of the mammalian senses of taste and smell is a powerful approach for the analysis of complex mixtures. Herein, we report on the effectiveness of a cross-reactive, supramolecular, peptide-based sensing array in differentiating and predicting the composition of red wine blends. Fifteen blends of Cabernet Sauvignon, Merlot and Cabernet Franc, in addition to the mono varietals, were used in this investigation. Linear Discriminant Analysis (LDA) showed a clear differentiation of blends based on tannin concentration and composition where certain mono varietals like Cabernet Sauvignon seemed to contribute less to the overall characteristics of the blend. Partial Least Squares (PLS) Regression and cross validation were used to build a predictive model for the responses of the receptors to eleven binary blends and the three mono varietals. The optimized model was later used to predict the percentage of each mono varietal in an independent test set composted of four tri-blends with a 15% average error. A partial least square regression model using the mouth-feel and taste descriptive sensory attributes of the wine blends revealed a strong correlation of the receptors to perceived astringency, which is indicative of selective binding to polyphenols in wine.

  16. Testing of commonly used mixing and sampling procedures to evaluate fertilizer blends prepared with matched and mismatched particle sizes.

    PubMed

    Hall, William L; Ramsey, Charles; Falls, J Harold

    2014-01-01

    Bulk blending of dry fertilizers is a common practice in the United States and around the world. This practice involves the mixing (either physically or volumetrically) of concentrated, high analysis raw materials. Blending is followed by bagging (for small volume application such as lawn and garden products), loading into truck transports, and spreading. The great majority of bulk blended products are not bagged but handled in bulk and transferred from the blender to a holding hopper. The product is then transferred to a transport vehicle, which may, or may not, also be a spreader. If the primary transport vehicle is not a spreader, then there is another transfer at the user site to a spreader for application. Segregation of materials that are mismatched due to size, density, or shape is an issue when attempting to effectively sample or evenly spread bulk blended products. This study, prepared in coordination with and supported by the Florida Department of Agriculture and Consumer Services and the Florida Fertilizer and Agrochemical Association, looks at the impact of varying particle size as it relates to blending, sampling, and application of bulk blends. The study addresses blends containing high ratios of N-P-K materials and varying (often small) quantities of the micronutrient Zn.

  17. Proceedings of the Annual Conference of the Military Testing Association Held in San Diego, California on 26-29 October 1992. Volume 2

    DTIC Science & Technology

    1992-10-29

    Blend engine stator vane K 620 Inspect engines removed from storag G 253 Blend engine turbine air seals K 621 Inspect fuel manifold test stands * 254...Assessment and Human Learning Skills G. F Fullerton D. P. Hunt 497 How Personnel Testing is Adapting to a Changing Air Force T S. Ziebell 503 Problems of...of Intelligence Among Navy and Air Force Personnel R. F Dillon 526 Session 25 Measuring Martial Attitudes: The Military Ethos Scale (MES) in Retrcspect

  18. Coupling Finite Element and Meshless Local Petrov-Galerkin Methods for Two-Dimensional Potential Problems

    NASA Technical Reports Server (NTRS)

    Chen, T.; Raju, I. S.

    2002-01-01

    A coupled finite element (FE) method and meshless local Petrov-Galerkin (MLPG) method for analyzing two-dimensional potential problems is presented in this paper. The analysis domain is subdivided into two regions, a finite element (FE) region and a meshless (MM) region. A single weighted residual form is written for the entire domain. Independent trial and test functions are assumed in the FE and MM regions. A transition region is created between the two regions. The transition region blends the trial and test functions of the FE and MM regions. The trial function blending is achieved using a technique similar to the 'Coons patch' method that is widely used in computer-aided geometric design. The test function blending is achieved by using either FE or MM test functions on the nodes in the transition element. The technique was evaluated by applying the coupled method to two potential problems governed by the Poisson equation. The coupled method passed all the patch test problems and gave accurate solutions for the problems studied.

  19. Attractiveness of MM-X Traps Baited with Human or Synthetic Odor to Mosquitoes (Diptera: Culicidae) in The Gambia

    PubMed Central

    QIU, YU TONG; SMALLEGANGE, RENATE C.; TER BRAAK, CAJO J. F.; SPITZEN, JEROEN; VAN LOON, JOOP J. A.; JAWARA, MUSA; MILLIGAN, PAUL; GALIMARD, AGNES M.; VAN BEEK, TERIS A.; KNOLS, BART G. J.; TAKKEN, WILLEM

    2013-01-01

    Chemical cues play an important role in the host-seeking behavior of blood-feeding mosquitoes (Diptera: Culicidae). A field study was carried out in The Gambia to investigate the effects of human odor or synthetic odor blends on the attraction of mosquitoes. MM-X traps baited with 16 odor blends to which carbon dioxide (CO2) was added were tested in four sets of experiments. In a second series of experiments, MM-X traps with 14 odor blends without CO2 were tested. A blend of ammonia and l-lactic acid with or without CO2 was used as control odor in series 1 and 2, respectively. Centers for Disease Control and Prevention (CDC) traps were placed in a traditional house and an experimental house to monitor mosquito densities during the experiments. The MM-X traps caught a total number of 196,756 mosquitoes, with the most abundant species belonging to the genera Mansonia (70.6%), Anopheles (17.5%), and Culex (11.5%). The most abundant mosquito species caught by the CDC traps (56,290 in total) belonged to the genera Mansonia (59.4%), Anopheles (16.0% An. gambiae s.l. Giles, and 11.3% An. ziemanni Grünberg), and Culex (11.6%). MM-X traps baited with synthetic blends were in many cases more attractive than MM-X traps baited with human odors. Addition of CO2 to synthetic odors substantially increased the catch of all mosquito species in the MM-X traps. A blend of ammonia + L-lactic acid + CO2 + 3-methylbutanoic acid was the most attractive odor for most mosquito species. The candidate odor blend shows the potential to enhance trap collections so that traps will provide better surveillance and possible control. PMID:18047195

  20. Ingestion of soy-whey blended protein augments sports performance and ameliorates exercise-induced fatigue in a rat exercise model.

    PubMed

    Ren, Guangxu; Yi, Suqing; Zhang, Hongru; Wang, Jing

    2017-02-22

    This study sought to determine the effects of soy-whey blended protein supplementation on sports performance and related biochemical parameters after long-term training. After a week of adaptation, eighteen 6-week-old male Wistar rats were randomly assigned to 3 groups: the standard chow diet plus whey protein (Whey) group, the standard chow diet plus soy-whey blended protein (BP) group and the standard chow diet only (control) group. Each group included 6 rats for the seven-week experiment. Before the experiment, the baseline values of body weight, grasping force and time to exhaustion due to the loaded-swimming test were recorded for each group. During the experimental period, all rats performed the loaded-swimming test until exhaustion five days each week. The results showed that the mean maximum grasping force of the BP group significantly increased between the 5 th and the 7 th week (p < 0.05) compared with the other groups. The ingestion of blended protein for 7 weeks significantly increased the mean time to exhaustion due to swimming by 1.5-fold and 1.2-fold compared with the control and Whey groups, respectively. The plasma levels of leucine, isoleucine and valine were significantly higher at 60 min after the blended protein intervention compared with the Whey and control interventions (p < 0.05). Furthermore, the ingestion of soy-whey blended protein enhanced the activities of lactate dehydrogenase and superoxide dismutase and decreased the levels of malondialdehyde in serum. These results collectively suggest that soy-whey blended protein ingestion with resistance exercise can improve sports performance and ameliorate exercise-induced fatigue in rats.

  1. CONCEPTUAL DESIGN ASSESSMENT FOR THE CO-FIRING OF BIO-REFINERY SUPPLIED LIGNIN PROJECT

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ted Berglund; Jeffrey T. Ranney; Carol L. Babb

    2002-04-01

    The major aspects of this project are proceeding toward completion. Prior to this quarter, design criteria, tentative site selection, facility layout, and preliminary facility cost estimates were completed and issued. Processing of bio-solids was completed, providing material for the pilot operations. Pilot facility hydrolysis production has been completed to produce lignin for co-fire testing and the lignin fuel was washed and dewatered. Both the lignin and bio-solids fuel materials for co-fire testing were sent to the co-fire facility (EERC) for evaluation and co-firing. EERC has received coal typical of the fuel to the TVA-Colbert boilers. This material was used atmore » EERC as baseline material and for mixing with the bio-fuel for combustion testing. All the combustion and fuel handling tests at EERC have been completed. During fuel preparation EERC reported no difficulties in fuel blending and handling. Preliminary co-fire test results indicate that the blending of lignin and bio-solids with the Colbert coal blend generally reduces NO{sub x} emissions, increases the reactivity of the coal, and increases the ash deposition rate on superheater surfaces. Deposits produced from the fuel blends, however, are more friable and hence easier to remove from tube surfaces relative to those produced from the baseline Colbert coal blend. The final co-fire testing report is being prepared at EERC and will be completed by the end of the second quarter of 2002. The TVA-Colbert facility has neared completion of the task to evaluate co-location of the Masada facility on the operation of the power generation facility. The TVA-Colbert fossil plant is fully capable of providing a reliable steam supply. The preferred steam supply connection points and steam pipeline routing have been identified. The environmental review of the pipeline routing has been completed and no major impacts have been identified. Detailed assessment of steam export impacts on the Colbert boiler system have been completed and a cost estimate for the steam supply system was completed. The cost estimate and output and heat rate impacts have been used to determine a preliminary price for the exported steam. TVA is further evaluating the impacts of adding lignin to the coal fuel blend and how the steam cost is impacted by proximity of the Masada biomass facility.« less

  2. Mechanical and thermal properties of conventional and microcellular injection molded poly (lactic acid)/poly (ε-caprolactone) blends.

    PubMed

    Zhao, Haibin; Zhao, Guoqun

    2016-01-01

    In view of their complementary properties, blending polylactide (PLA) with poly (ε-caprolactone) (PCL) becomes a good choice to improve PLA's properties without compromising its biodegradability. A series of blends of biodegradable PLA and PCL with different mass fraction were prepared by melt mixing. Standard tensile bars were produced by both conventional and microcellular injection molding to study their mechanical and thermal properties. With the increase in PCL content, the blend showed decreased tensile strength and modulus; however, elongation was dramatically increased. With the addition of PCL, the failure mode changed from brittle fracture of the neat PLA to ductile fracture of the blend as demonstrated by tensile test. Various theoretical models based on dispersion and interface adhesion were used to predict the Young's modulus and the results shows the experimental data are consistent with the predictions of the foam model and Kerner-Uemura-Takayangi model. The thermal behavior of the blends was investigated by DSC and TGA. The melting temperature and the degree of crystallinity of PCL in the PLA/PCL did not significantly change with the PCL content increasing in the whole range of blends composition. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Treeing phenomenon of thermoplastic polyethylene blends for recyclable cable insulation materials

    NASA Astrophysics Data System (ADS)

    Li, Lunzhi; Zhang, Kai; Zhong, Lisheng; Gao, Jinghui; Xu, Man; Chen, Guanghui; Fu, Mingli

    2017-02-01

    Owing to its good recyclability and low processing energy consumption, non-crosslinked polyethylene blends (e.g. LLDPE-HDPE blends) are considered as one of potential environmental-friendly substitutions for crosslinked polyethylene (XLPE) as cable insulation material. Although extensive work has been performed for measuring the basic dielectric properties, there is a lack of the investigations on the aging properties for such a material system, which hinders the evaluation of reliability and lifetime of the material for cable insulation. In this paper, we study the electric aging phenomenon of 0.7LLDPE-0.3HDPE blending material by investigating the treeing behavior, and its comparison with XLPE and LLDPE. Treeing tests show that the 0.7LLDPE-0.3HDPE blends have lower probability for treeing as well as smaller treeing dimensions. Further thermal analysis and microstructure study results suggest that the blends exhibit larger proportion of thick lamellae and higher crystallinity with homogeneously-distributed amorphous region, which is responsible for good anti-treeing performance. Our finding provides the evidence that the 0.7LLDPE-0.3HDPE blends exhibits better electric-aging-retardance properties than XLPE, which may result in a potential application for cable insulation.

  4. Preparation and emission characteristics of ethanol-diesel fuel blends.

    PubMed

    Zhang, Run-Duo; He, Hong; Shi, Xiao-Yan; Zhang, Chang-Bin; He, Bang-Quan; Wang, Jian-Xin

    2004-01-01

    The preparation of ethanol-diesel fuel blends and their emission characteristics were investigated. Results showed the absolute ethanol can dissolve in diesel fuel at an arbitrary ratio and a small quantity of water(0.2%) addition can lead to the phase separation of blends. An organic additive was synthesized and it can develop the ability of resistance to water and maintain the stability of ethanol-diesel-trace amounts of water system. The emission characteristics of 10%, 20%, and 30% ethanol-diesel fuel blends, with or without additives, were compared with those of diesel fuel in a direct injection (DI) diesel engine. The experimental results indicated that the blend of ethanol with diesel fuel significantly reduced the concentrations of smoke, hydrocarbon (HC), and carbon monoxide (CO) in exhaust gas. Using 20% ethanol-diesel fuel blend with the additive of 2% of the total volume, the optimum mixing ratio was achieved, at which the bench diesel engine testing showed a significant decrease in exhaust gas. Bosch smoke number was reduced by 55%, HC emission by 70%, and CO emission by 45%, at 13 kW/1540 r/min. However, ethanol-diesel fuel blends produced a few ppm acetaldehydes and more ethanol in exhaust gas.

  5. A FIELD TEST USING COAL:DRDF BLENDS IN SPREADER STOKER-FIRED BOILERS

    EPA Science Inventory

    This program was conducted to characterize and demonstrate the technical, economic, and environmental feasibility of combustion densified forms of refuse derived fuel (dRDF) blended with coal in spreader stoker-fired boilers. A total of 258.5 Mg (285 tons) of pelletized 1/2-inch-...

  6. 40 CFR 86.308-79 - Gas specifications.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... blending. Nitrogen shall be the predominant diluent with the balance oxygen. Blends required for gasoline... zero grade nitrogen as a diluent. Combined CO and CO2 span gases are permitted. Zero grade nitrogen... analyzer shall be propane with zero-grade nitrogen as a diluent when testing gasoline-fueled engines. For...

  7. 40 CFR 86.308-79 - Gas specifications.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... blending. Nitrogen shall be the predominant diluent with the balance oxygen. Blends required for gasoline... zero grade nitrogen as a diluent. Combined CO and CO2 span gases are permitted. Zero grade nitrogen... analyzer shall be propane with zero-grade nitrogen as a diluent when testing gasoline-fueled engines. For...

  8. 40 CFR Table 4 to Subpart Oooo of... - Default Organic HAP Mass Fraction for Solvents and Solvent Blends

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... fraction values in the following table for solvent blends for which you do not have test data or... spirits 64742-89-6 0.15 Toluene. 14. Low aromatic white spirit 64742-82-1 0 None. 15. Mineral spirits...

  9. 40 CFR Table 3 to Subpart IIIi of... - Default Organic HAP Mass Fraction for Solvents and Solvent Blends

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... fraction values in the following table for solvent blends for which you do not have test data or... spirits 64742-89-6 0.15 Toluene. 14. Low aromatic white spirit 64742-82-1 0 None. 15. Mineral spirits...

  10. 40 CFR Table 4 to Subpart Oooo of... - Default Organic HAP Mass Fraction for Solvents and Solvent Blends

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... fraction values in the following table for solvent blends for which you do not have test data or... spirits 64742-89-6 0.15 Toluene. 14. Low aromatic white spirit 64742-82-1 0 None. 15. Mineral spirits...

  11. 40 CFR Table 3 to Subpart IIIi of... - Default Organic HAP Mass Fraction for Solvents and Solvent Blends

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... fraction values in the following table for solvent blends for which you do not have test data or... spirits 64742-89-6 0.15 Toluene. 14. Low aromatic white spirit 64742-82-1 0 None. 15. Mineral spirits...

  12. Locomotive emissions measurements for various blends of biodiesel fuel.

    DOT National Transportation Integrated Search

    2014-12-01

    The objective of this project was to assess the effects of various blends of biodiesel on locomotive engine exhaust emissions. The : emission tests were conducted on two locomotive models, a Tier 2 EMD SD70ACe and a Tier 1 Plus GE Dash9-44CW, using t...

  13. Rheology and mechanics of polyether(ether)ketone - Polyetherimide blends for composites in aeronautics

    NASA Astrophysics Data System (ADS)

    Rosa, Mattia; Grassia, Luigi; D'Amore, Alberto; Carotenuto, Claudia; Minale, Mario

    2016-05-01

    In the present work rheological and mechanical properties of PEEK-PEI blends were investigated. Besides the pure components, blends with PEI concentration ranging from 10% to 90% in mass were considered. Oscillatory experiments in controlled atmosphere were conducted at different frequencies and temperatures. The frequency responses at different temperatures allowed using the TTS principle to reconstruct the master curves. All systems showed a shear thinning behavior and a flux index increasing with the percentage of PEI. The zero-shear viscosity was computed with the implementation of the Cross model and showed a decreasing behavior with the percentage of PEI. The relaxation time estimated from the crossover value of storage and loss moduli didn't change significantly with blend composition, suggesting the non-sensibility of the elasticity of the system. Lastly, tensile tests were executed to investigate the dependence of Young modulus in the different blends.

  14. Preparation of 3D fibroin/chitosan blend porous scaffold for tissue engineering via a simplified method.

    PubMed

    Ruan, Yuhui; Lin, Hong; Yao, Jinrong; Chen, Zhengrong; Shao, Zhengzhong

    2011-03-10

    In this work, we developed a simple and flexible method to manufacture a 3D porous scaffold based on the blend of regenerated silk fibroin (RSF) and chitosan (CS). No crosslinker or other toxic reagents were used in this method. The pores of resulted 3D scaffolds were connected with each other, and their sizes could be easily controlled by the concentration of the mixed solution. Compared with pure RSF scaffolds, the water absorptivities of these RSF/CS blend scaffolds with significantly enhanced mechanical properties were greatly increased. The results of MTT and RT-PCR tests indicated that the chondrocytes grew very well in these blend RSF/CS porous scaffolds. This suggested that the RSF/CS blend scaffold prepared by this new method could be a promising candidate for applications in tissue engineering. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Physicochemical properties and potential food applications of Moringa oleifera seed oil blended with other vegetable oils.

    PubMed

    Dollah, Sarafhana; Abdulkarim, Sabo Muhammad; Ahmad, Siti Hajar; Khoramnia, Anahita; Ghazali, Hasanah Mohd

    2014-01-01

    Blends (30:70, 50:50 and 70:30 w/w) of Moringa oleifera seed oil (MoO) with palm olein (PO), palm stearin (PS), palm kernel oil (PKO) and virgin coconut oil (VCO) were prepared. To determine the physicochemical properties of the blends, the iodine value (IV), saponication value (SV), fatty acid (FA) composition, triacylglycerol (TAG) composition, thermal behaviour (DSC) and solid fat content (SFC) tests were analysed. The incorporation of high oleic acid (81.73%) MoO into the blends resulted in the reduction of palmitic acid content of PO and PS from 36.38% to 17.17% and 54.66% to 14.39% and lauric acid content of PKO and VCO from 50.63% to 17.70% and 51.26% to 26.05% respectively while oleic acid and degree of unsaturation were increased in all blends. Changes in the FA composition and TAG profile have significantly affected the thermal behavior and solid fat content of the oil blends. In MoO/PO blends the melting temperature of MoO decreased while, in MoO/PS, MoO/PKO and MoO/VCO blends, it increased indicating produce of zero-trans harder oil blends without use of partial hydrogenation. The spreadability of PS, PKO and VCO in low temperatures was also increased due to incorporation of MoO. The melting point of PS significantly decreased in MoO/PS blends which proved to be suitable for high oleic bakery shortening and confectionary shortening formulation. The finding appears that blending of MoO with other vegetable oils would enable the initial properties of the oils to be modified or altered and provide functional and nutritional attributes for usage in various food applications, increasing the possibilities for the commercial use of these oils.

  16. Ionic liquids for low-tension oil recovery processes: Phase behavior tests.

    PubMed

    Rodriguez-Escontrela, Iria; Puerto, Maura C; Miller, Clarence A; Soto, Ana

    2017-10-15

    Chemical flooding with surfactants for reducing oil-brine interfacial tensions (IFTs) to mobilize residual oil trapped by capillary forces has a great potential for Enhanced Oil Recovery (EOR). Surface-active ionic liquids (SAILs) constitute a class of surfactants that has recently been proposed for this application. For the first time, SAILs or their blends with an anionic surfactant are studied by determining equilibrium phase behavior for systems of about unit water-oil ratio at various temperatures. The test fluids were model alkane and aromatic oils, NaCl brine, and synthetic hard seawater (SW). Patterns of microemulsions observed are those of classical phase behavior (Winsor I-III-II transition) known to correlate with low IFTs. The two anionic room-temperature SAILs tested were made from common anionic surfactants by substituting imidazolium or phosphonium cations for sodium. These two anionic and two cationic SAILs were found to have little potential for EOR when tested individually. Thus, also tested were blends of an anionic internal olefin sulfonate (IOS) surfactant with one of the anionic SAILs and both cationic SAILs. Most promising for EOR was the anionic/cationic surfactant blend of IOS with [C 12 mim]Br in SW. A low equilibrium IFT of ∼2·10 -3 mN/m was measured between n-octane and an aqueous solution having the optimal blend ratio for this system at 25°C. Copyright © 2017 Elsevier Inc. All rights reserved.

  17. Blended-Wing-Body Low-Speed Flight Dynamics: Summary of Ground Tests and Sample Results

    NASA Technical Reports Server (NTRS)

    Vicroy, Dan D.

    2009-01-01

    A series of low-speed wind tunnel tests of a Blended-Wing-Body tri-jet configuration to evaluate the low-speed static and dynamic stability and control characteristics over the full envelope of angle of attack and sideslip are summarized. These data were collected for use in simulation studies of the edge-of-the-envelope and potential out-of-control flight characteristics. Some selected results with lessons learned are presented.

  18. The Knock-Limited Performance of Fuel Blends Containing Aromatics V : N-Propylbenzene, N-Butylbenzene, Isobutylbenzene, M-Xylene, and 1-Isopropyl-4-Methylbenzene

    NASA Technical Reports Server (NTRS)

    Meyer, Carl L.; Branstetter, J. Robert

    1946-01-01

    Results are reported of knock-limited tests of five aromatics, each individually blended with selected base fuels and tested with and without TEL, using 17.6, F-4, and F-3 small-scale engines. The five aromatics rated in the following order of decreasing antiknock effectiveness at fuel/air ratio 0.10: m-xylene, 1-isopropyl-4-methylbenzene, n-propylbenzene, isobutylbenzene, and n-butylbenzene.

  19. The Effect of the Diesel Cetane Number on Exhaust Emissions Characteristics by Various Additives

    NASA Astrophysics Data System (ADS)

    Lim, Yunsung; Seo, Choongyeol; Lee, Jongtae; Kang, Daeil; Kim, Jeong Soo; Kim, Hyung Jun

    This paper described the effect of the diesel cetane number on exhaust emissions characteristics according to various additives. In addition, the emission characteristics of test fuels blended with three additives (GTL, biodiesel and additive for improving CN) were analyzed and the potential for uses of these additives were evaluated in this study. To achieve this purpose, the test diesel vehicle with a two-thousand cubic centimeter displacement was used to analyze the emission characteristics according to the CN. Also, the NEDC (New European Driving Cycle) was applied as the test mode which is widely used as the test method for environmental certification of diesel vehicles. To analyze the characteristics of HAPs, the VOCs and PAHs were analyzed from the BTEX and the particulate matter, respectively. The analysis results revealed that the CO emissions show the largest reduction rate while the NOx+THC emissions are reduced at a low as the CN got higher. In the NEDC mode, the PM emissions in the EUDC mode were found to be at a lower level than those in the UDC mode. As for the VOCs and PAHs characteristics, the VOCs of the CN 58 show the lowest amounts. Also, the PAHs of diesel blended with GTL show the highest level, followed by those of diesel blended with biodiesel and diesel blended with cetane additive.

  20. Postprandial lipid responses of butter blend containing fish oil in a single-meal study in humans.

    PubMed

    Overgaard, Julie; Porsgaard, Trine; Guo, Zheng; Lauritzen, Lotte; Mu, Huiling

    2008-10-01

    The postprandial effects of a butter product containing fish oil were investigated in a single-meal, randomized crossover study with a commercial butter product as the control. Twelve healthy males consumed two test meals with (13)C-labelled cholesterol (45 mg) and either an interesterified butter blend with fish oil (352 mg n-3 long-chain PUFA (LCPUFA)) or the commercial butter blend. Blood samples were collected after the meals and in the fasting condition on the test day and the following morning, and were analysed for cholesterol absorption, plasma lipid profile and fatty acid composition. No significant difference in the postprandial plasma fatty acid composition was observed between the groups, neither difference in cholesterol absorption, plasma cholesterol or the cholesterol contents of plasma lipoproteins. The incorporation of fish oil in the butter resulted in a significant lower concentration of triacylglycerols in the plasma 2 h after the meal in comparison with the commercial butter blend (p = 0.02); there was, however, no significant difference 24 h after the meal. In conclusion, fish oil-enriched butter blend provides a source to increase the intake of n-3 LCPUFA in the population, but has no acute effect on cholesterol absorption and plasma cholesterol concentration in human.

  1. Coalescence in PLA-PBAT blends under shear flow: Effects of blend preparation and PLA molecular weight

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Nofar, M.; Heuzey, M. C.; Carreau, P. J., E-mail: pierre.carreau@polymtl.ca

    Blends containing 75 wt. % of an amorphous polylactide (PLA) with two different molecular weights and 25 wt. % of a poly[(butylene adipate)-co-terephthalate] (PBAT) were prepared using either a Brabender batch mixer or a twin-screw extruder. These compounds were selected because blending PLA with PBAT can overcome various drawbacks of PLA such as its brittleness and processability limitations. In this study, we investigated the effects of varying the molecular weight of the PLA matrix and of two different mixing processes on the blend morphology and, further, on droplet coalescence during shearing. The rheological properties of these blends were investigated and the interfacialmore » properties were analyzed using the Palierne emulsion model. Droplet coalescence was investigated by applying shear flows of 0.05 and 0.20 s{sup −1} at a fixed strain of 60. Subsequently, small amplitude oscillatory shear tests were conducted to investigate changes in the viscoelastic properties. The morphology of the blends was also examined using scanning electron microscope (SEM) micrographs. It was observed that the PBAT droplets were much smaller when twin-screw extrusion was used for the blend preparation. Shearing at 0.05 s{sup −1} induced significant droplet coalescence in all blends, but coalescence and changes in the viscoelastic properties were much more pronounced for the PLA-PBAT blend based on a lower molecular weight PLA. The viscoelastic responses were also somehow affected by the thermal degradation of the PLA matrix during the experiments.« less

  2. Degradation of PVC/HC blends. II. Terrestrial plant growth test.

    PubMed

    Pascu, Mihaela; Agafiţei, Gabriela-Elena; Profire, Lenuţa; Vasile, Cornelia

    2009-01-01

    The behavior at degradation by soil burial of some plasticized polyvinyl chloride (PVC) based blends with a variable content of hydrolyzed collagen (HC) has been followed. The modifications induced in the environment by the polymer systems (pH variation, physiologic state of the plants, assimilatory pigments) were studied. Using the growth test of the terrestrial plants, we followed the development of Triticum (wheat), Helianthus annus minimus (little sunflower), Pisum sativum (pea), and Vicia X hybrida hort, during a vegetation cycle. After the harvest, for each plant, the quantities of chlorophyll and carotenoidic pigments and of trace- and macroelements were determined. It was proved that, in the presence of polymer blends, the plants do not suffer morphological and physiological modifications, the products released in the culture soil being not toxic for the plants growth.

  3. Study of EPDM/PP polymeric blends: mechanical behavior and effects of compatibilization

    NASA Astrophysics Data System (ADS)

    Bouchart, Vanessa; Bhatnagar, N.; Brieu, Mathias; Ghosh, A. K.; Kondo, Djimedo

    2008-09-01

    A blend of Ethylene Propylene Diene Monomer (EPDM) rubber reinforced by polypropylene (PP) particles has been processed and its hyperelastic behavior has been characterized under cyclic uni-axial tensile tests. The experimental results show a significant effect of the fraction of polypropylene particles (10%, 25% and 30% by weight). Moreover, from another series of tests conducted on materials containing compatibilizers at different mass concentration, it is observed that the introduction of a compatibilizer increases the rigidity of the blends and affects notably their macroscopic behavior. These observations are interpreted as a consequence of the modification at microlevel of adherence between particles and matrix phases. The use of a nonlinear micromechanical model allows us to confirm this interpretation. To cite this article: V. Bouchart et al., C. R. Mecanique 336 (2008).

  4. Reverse indentation size effects in gamma irradiated blood compatible blend films of chitosan-poly (vinyl alcohol) for possible medical applications.

    PubMed

    Bisen, D S; Bhatt, Rinkesh; Bajpai, A K; Bajpai, R; Katare, R

    2017-02-01

    In the present work binary blends of polyvinyl alcohol (PVA) and chitosan (CS) were prepared by solution cast method and characterized by analytical methods like FTIR, XRD and SEM for seeking structural and morphological information. The blends were exposed to gamma radiation and evaluated for their improved mechanical strength. It was found that the tensile strength and microhardness increased after irradiation of CS-PVA films. Plastic effect due to absorption of water molecules and scissoring effect due to gamma irradiation were found to decrease the softness or increase the microhardness of the blends. Improved mechanical properties were attributed to intermolecular and intramolecular hydrogen bonds and adhesive nature of the blends also. The blends were also investigated for water intake behavior and in vitro blood compatibility property on the basis of certain in vitro tests like protein adsorption, haemolysis and blood clot formation on the un-irradiated and irradiated blend samples. The increased % swelling with time could be assigned to the fact that increasing water content facilitates the phase separation process within the blend which results in advancement in interstitial nano-void spaces which are occupied by water molecules. The blood compatibility results showed that when the amount of CS was varied from 0.5% to 2%, the amount of blood clot and percent haemolysis decreased while the protein adsorption increased with increasing CS content of the blend films. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. Effect of TiO2-Crystal Forms on the Photo-Degradation of EVA/PLA Blend Under Accelerated Weather Testing

    NASA Astrophysics Data System (ADS)

    Van Cong, Do; Trang, Nguyen Thi Thu; Giang, Nguyen Vu; Lam, Tran Dai; Hoang, Thai

    2016-05-01

    Photo-degradation of poly (ethylene-co-vinyl acetate) (EVA)/poly (lactic acid) (PLA) blend and EVA/PLA/TiO2 nanocomposites was carried out under accelerated weather testing conditions by alternating cycles of ultraviolet (UV) light and moisture at controlled and elevated temperatures. The characters, properties, and morphology of these materials before and after accelerated weather testing were determined by Fourier transform infrared spectroscopy, colour changes, viscosity, tensile test, thermogravimetric analysis, and field emission scanning electron microscopy. The increases in the content of oxygen-containing groups, colour changes; the decreases in viscosity, tensile properties, and thermal stability of these materials after accelerated weather testing are the evidence for the photo-degradation of the blend and nanocomposites. After accelerated weather testing, the appearance of many micro-holes and micro-pores on the surface of the collected samples was observed. The photo-degradation degree of the nanocomposites depended on the TiO2-crystal form. Rutile TiO2 do not enhance the degradation, but anatase and mixed crystals TiO2 nanoparticles promoted the degradation of the nanocomposites. Particularly, the mixed crystals TiO2 nanoparticles showed the highest photo-catalytic activity of the nanocomposites.

  6. Hemorrhagic versus ischemic stroke: Who can best benefit from blended conventional physiotherapy with robotic-assisted gait therapy?

    PubMed

    Dierick, Frédéric; Dehas, Mélanie; Isambert, Jean-Luc; Injeyan, Soizic; Bouché, Anne-France; Bleyenheuft, Yannick; Portnoy, Sigal

    2017-01-01

    Contrary to common belief of clinicians that hemorrhagic stroke survivors have better functional prognoses than ischemic, recent studies show that ischemic survivors could experience similar or even better functional improvements. However, the influence of stroke subtype on gait and posture outcomes following an intervention blending conventional physiotherapy with robotic-assisted gait therapy is missing. This study compared gait and posture outcome measures between ambulatory hemorrhagic patients and ischemic patients, who received a similar 4 weeks' intervention blending a conventional bottom-up physiotherapy approach and an exoskeleton top-down robotic-assisted gait training (RAGT) approach with Lokomat. Forty adult hemiparetic stroke inpatient subjects were recruited: 20 hemorrhagic and 20 ischemic, matched by age, gender, side of hemisphere lesion, stroke severity, and locomotor impairments. Functional Ambulation Category, Postural Assessment Scale for Stroke, Tinetti Performance Oriented Mobility Assessment, 6 Minutes Walk Test, Timed Up and Go and 10-Meter Walk Test were performed before and after a 4-week long intervention. Functional gains were calculated for all tests. Hemorrhagic and ischemic subjects showed significant improvements in Functional Ambulation Category (P<0.001 and P = 0.008, respectively), Postural Assessment Scale for Stroke (P<0.001 and P = 0.003), 6 Minutes Walk Test (P = 0.003 and P = 0.015) and 10-Meter Walk Test (P = 0.001 and P = 0.024). Ischemic patients also showed significant improvements in Timed Up and Go. Significantly greater mean Functional Ambulation Category and Tinetti Performance Oriented Mobility Assessment gains were observed for hemorrhagic compared to ischemic, with large (dz = 0.81) and medium (dz = 0.66) effect sizes, respectively. Overall, both groups exhibited quasi similar functional improvements and benefits from the same type, length and frequency of blended conventional physiotherapy and RAGT protocol. The use of intensive treatment plans blending top-down physiotherapy and bottom-up robotic approaches is promising for post-stroke rehabilitation.

  7. Hemorrhagic versus ischemic stroke: Who can best benefit from blended conventional physiotherapy with robotic-assisted gait therapy?

    PubMed Central

    Dehas, Mélanie; Isambert, Jean-Luc; Injeyan, Soizic; Bouché, Anne-France; Bleyenheuft, Yannick; Portnoy, Sigal

    2017-01-01

    Background Contrary to common belief of clinicians that hemorrhagic stroke survivors have better functional prognoses than ischemic, recent studies show that ischemic survivors could experience similar or even better functional improvements. However, the influence of stroke subtype on gait and posture outcomes following an intervention blending conventional physiotherapy with robotic-assisted gait therapy is missing. Objective This study compared gait and posture outcome measures between ambulatory hemorrhagic patients and ischemic patients, who received a similar 4 weeks’ intervention blending a conventional bottom-up physiotherapy approach and an exoskeleton top-down robotic-assisted gait training (RAGT) approach with Lokomat. Methods Forty adult hemiparetic stroke inpatient subjects were recruited: 20 hemorrhagic and 20 ischemic, matched by age, gender, side of hemisphere lesion, stroke severity, and locomotor impairments. Functional Ambulation Category, Postural Assessment Scale for Stroke, Tinetti Performance Oriented Mobility Assessment, 6 Minutes Walk Test, Timed Up and Go and 10-Meter Walk Test were performed before and after a 4-week long intervention. Functional gains were calculated for all tests. Results Hemorrhagic and ischemic subjects showed significant improvements in Functional Ambulation Category (P<0.001 and P = 0.008, respectively), Postural Assessment Scale for Stroke (P<0.001 and P = 0.003), 6 Minutes Walk Test (P = 0.003 and P = 0.015) and 10-Meter Walk Test (P = 0.001 and P = 0.024). Ischemic patients also showed significant improvements in Timed Up and Go. Significantly greater mean Functional Ambulation Category and Tinetti Performance Oriented Mobility Assessment gains were observed for hemorrhagic compared to ischemic, with large (dz = 0.81) and medium (dz = 0.66) effect sizes, respectively. Conclusion Overall, both groups exhibited quasi similar functional improvements and benefits from the same type, length and frequency of blended conventional physiotherapy and RAGT protocol. The use of intensive treatment plans blending top-down physiotherapy and bottom-up robotic approaches is promising for post-stroke rehabilitation. PMID:28575054

  8. DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    The objective of Task I is to prepare and evaluate catalysts and to develop efficient reactor systems for the selective conversion of hydrogen-lean synthesis gas to alcohol fuel extenders and octane enhancers. In Task 1, during this reporting period, we encountered and solved a problem in the analysis of the reaction products containing a small amount of heavy components. Subsequently, we continued with the major thrusts of the program. We analyzed the results from our preliminary studies on the packed-bed membrane reactor using the BASF methanol synthesis catalyst. We developed a quantitative model to describe the performance of the reactor.more » The effect of varying permeances and the effect of catalyst aging are being incorporated into the model. Secondly, we resumed our more- detailed parametric studies on selected non-sulfide Mo-based catalysts. Finally, we continue with the analysis of data from the kinetic study of a sulfided carbon-supported potassium-doped molybdenum-cobalt catalyst in the Rotoberty reactor. We have completed catalyst screening at UCC. The complete characterization of selected catalysts has been started. In Task 2, the fuel blends of alcohol and unleaded test gas 96 (UTG 96) have been made and tests have been completed. The testing includes knock resistance tests and emissions tests. Emissions tests were conducted when the engine was optimized for the particular blend being tested (i.e. where the engine produced the most power when running on the blend in question). The data shows that the presence of alcohol in the fuel increases the fuel`s ability to resist knock. Because of this, when the engine was optimized for use with alcohol blends, the engine produced more power and lower emission rates.« less

  9. Optimization of Rice bran biodiesel blends on CI engine and investigating its effects

    NASA Astrophysics Data System (ADS)

    Jayaprabakar, J.; Dey, Biraj; Dey, Krishanu; Hareesh, Batchu; Anish, M.

    2017-05-01

    Bio-diesel can be produced from various plant oils like soybean, sunflower or rice bran. Here the focus is on converting the rice bran oil into bio-diesel which is produced by transesterifying the rice bran oil with a low molecular weight alcohol (methanol) and a non-conventional catalyst (lipase). Using a lipase based catalyst brings down the cost of bio diesel production significantly by reducing the number of washing cycles and its ability to be reused further. Four different blends of B10, B20, B30, B40 and straight diesel are tested in a single cylinder, fourstroke, vertical air cooled Kirloskar Diesel Engine having ignition timing of 23° before Top Dead Centre (TDC). As compared to straight diesel the Brake Thermal Efficiency (BTE) value for all the blends are higher. The Specific Fuel Consumption (BSFC) values for most of the blends are less as compared to diesel. Emissions of CO, CO2 and HC for all the blends decreased quite significantly. As a summary, the blend B20 records better performance as well as emission characteristics as compared to diesel.

  10. Experimental investigation on performance and exhaust emissions of castor oil biodiesel from a diesel engine.

    PubMed

    Shojaeefard, M H; Etgahni, M M; Meisami, F; Barari, A

    2013-01-01

    Biodiesel, produced from plant and animal oils, is an important alternative to fossil fuels because, apart from dwindling supply, the latter are a major source of air pollution. In this investigation, effects of castor oil biodiesel blends have been examined on diesel engine performance and emissions. After producing castor methyl ester by the transesterification method and measuring its characteristics, the experiments were performed on a four cylinder, turbocharged, direct injection, diesel engine. Engine performance (power, torque, brake specific fuel consumption and thermal efficiency) and exhaust emissions were analysed at various engine speeds. All the tests were done under 75% full load. Furthermore, the volumetric blending ratios of biodiesel with conventional diesel fuel were set at 5, 10, 15, 20 and 30%. The results indicate that lower blends of biodiesel provide acceptable engine performance and even improve it. Meanwhile, exhaust emissions are much decreased. Finally, a 15% blend of castor oil-biodiesel was picked as the optimized blend of biodiesel-diesel. It was found that lower blends of castor biodiesel are an acceptable fuel alternative for the engine.

  11. A comparative study of almond biodiesel-diesel blends for diesel engine in terms of performance and emissions.

    PubMed

    Abu-Hamdeh, Nidal H; Alnefaie, Khaled A

    2015-01-01

    This paper investigates the opportunity of using almond oil as a renewable and alternative fuel source. Different fuel blends containing 10, 30, and 50% almond biodiesel (B10, B30, and B50) with diesel fuel (B0) were prepared and the influence of these blends on emissions and some performance parameters under various load conditions were inspected using a diesel engine. Measured engine performance parameters have generally shown a slight increase in exhaust gas temperature and in brake specific fuel consumption and a slight decrease in brake thermal efficiency. Gases investigated were carbon monoxide (CO) and oxides of nitrogen (NOx). Furthermore, the concentration of the total particulate and the unburned fuel emissions in the exhaust gas were tested. A blend of almond biodiesel with diesel fuel gradually reduced the engine CO and total particulate emissions compared to diesel fuel alone. This reduction increased with more almond biodiesel blended into the fuel. Finally, a slight increase in engine NO x using blends of almond biodiesel was measured.

  12. A Comparative Study of Almond Biodiesel-Diesel Blends for Diesel Engine in Terms of Performance and Emissions

    PubMed Central

    Alnefaie, Khaled A.

    2015-01-01

    This paper investigates the opportunity of using almond oil as a renewable and alternative fuel source. Different fuel blends containing 10, 30, and 50% almond biodiesel (B10, B30, and B50) with diesel fuel (B0) were prepared and the influence of these blends on emissions and some performance parameters under various load conditions were inspected using a diesel engine. Measured engine performance parameters have generally shown a slight increase in exhaust gas temperature and in brake specific fuel consumption and a slight decrease in brake thermal efficiency. Gases investigated were carbon monoxide (CO) and oxides of nitrogen (NOx). Furthermore, the concentration of the total particulate and the unburned fuel emissions in the exhaust gas were tested. A blend of almond biodiesel with diesel fuel gradually reduced the engine CO and total particulate emissions compared to diesel fuel alone. This reduction increased with more almond biodiesel blended into the fuel. Finally, a slight increase in engine NOx using blends of almond biodiesel was measured. PMID:25874218

  13. Experimentation on bio-kerosene stove using organic additive

    NASA Astrophysics Data System (ADS)

    Varshini, M.; Shetty, Divakar

    2017-07-01

    One of the basic worthy item used in most of the villages even now a day's also is the kerosene stove. But in the current scenario, the petroleum products are been replenished. So an alternate fuel should be found in order delve. This work is to check the contingency of blending pongamia oil and kerosene in which is used as an additive. Pongamia is one of the forest based fast growing evergreen tree which is capable of yielding 9 - 90 kg seeds from which 25% of oil can be extracted. Distilled cow urine is to be used so that the fuel can be stored for longer time and is odorless. Blends of 10% to 70% neat pongamia oil - kerosene(KEP) and pongamia oil - kerosene with additive(KEPWA) are prepared. The properties such as flash point, fire point and viscosity are determined. The blends are been compared by doing emission test. The blends with additive showed better properties and reducing in emission characteristics compared to neat blends. It is also observed that emission of CO is decreasing with increasing blends.

  14. A randomized, investigator-masked clinical evaluation of the efficacy and safety of clobetasol propionate 0.05% shampoo and tar blend 1% shampoo in the treatment of moderate to severe scalp psoriasis.

    PubMed

    Griffiths, Christopher E M; Finlay, Andrew Y; Fleming, Colin J; Barker, Jonathan N W N; Mizzi, Fabienne; Arsonnaud, Stéphanie

    2006-01-01

    The clinical benefit of currently available tar blend shampoos for the treatment of scalp psoriasis is restricted due to their limited efficacy, low cosmetic appeal and potential for carcinogenicity. This 4-week multicentre, randomized, parallel-group, investigator-masked study included 162 subjects and aimed to compare the efficacy, safety and cosmetic acceptability of clobetasol propionate 0.05% shampoo versus a currently marketed tar blend 1% shampoo in subjects with moderate to severe scalp psoriasis. Clobetasol propionate shampoo was superior to tar blend shampoo with respect to all efficacy variables tested (p<0.001): Total and Global Severity Score; erythema; plaque thickening; desquamation; pruritus; total scalp area involved; and the subject's global assessment of clinical improvement. Both treatments were safe and well-tolerated. Furthermore, more subjects indicated that clobetasol propionate shampoo was more cosmetically acceptable than tar blend shampoo. Clobetasol propionate 0.05% shampoo is a good alternative to tar blend shampoo in the treatment of moderate to severe scalp psoriasis.

  15. Determination of Component Contents of Blend Oil Based on Characteristics Peak Value Integration.

    PubMed

    Xu, Jing; Hou, Pei-guo; Wang, Yu-tian; Pan, Zhao

    2016-01-01

    Edible blend oil market is confused at present. It has some problems such as confusing concepts, randomly named, shoddy and especially the fuzzy standard of compositions and ratios in blend oil. The national standard fails to come on time after eight years. The basic reason is the lack of qualitative and quantitative detection of vegetable oils in blend oil. Edible blend oil is mixed by different vegetable oils according to a certain proportion. Its nutrition is rich. Blend oil is eaten frequently in daily life. Different vegetable oil contains a certain components. The mixed vegetable oil can make full use of their nutrients and make the nutrients more balanced in blend oil. It is conducive to people's health. It is an effectively way to monitor blend oil market by the accurate determination of single vegetable oil content in blend oil. The types of blend oil are known, so we only need for accurate determination of its content. Three dimensional fluorescence spectra are used for the contents in blend oil. A new method of data processing is proposed with calculation of characteristics peak value integration in chosen characteristic area based on Quasi-Monte Carlo method, combined with Neural network method to solve nonlinear equations to obtain single vegetable oil content in blend oil. Peanut oil, soybean oil and sunflower oil are used as research object to reconcile into edible blend oil, with single oil regarded whole, not considered each oil's components. Recovery rates of 10 configurations of edible harmonic oil is measured to verify the validity of the method of characteristics peak value integration. An effective method is provided to detect components content of complex mixture in high sensitivity. Accuracy of recovery rats is increased, compared the common method of solution of linear equations used to detect components content of mixture. It can be used in the testing of kinds and content of edible vegetable oil in blend oil for the food quality detection, and provide an effective reference for the creation of national standards.

  16. A model of blended learning in a preclinical course in prosthetic dentistry.

    PubMed

    Reissmann, Daniel R; Sierwald, Ira; Berger, Florian; Heydecke, Guido

    2015-02-01

    The aim of this study was to evaluate the use of blending learning that added online tools to traditional learning methods in a preclinical course in prosthetic dentistry at one dental school in Germany. The e-learning modules were comprised of three main components: fundamental principles, additional information, and learning objective tests. Video recordings of practical demonstrations were prepared and cut into sequences meant to achieve single learning goals. The films were accompanied by background information and, after digital processing, were made available online. Additionally, learning objective tests and learning contents were integrated. Evaluations of 71 of 89 students (response rate: 80%) in the course with the integrated e-learning content were available for the study. Compared with evaluation results of the previous years, a substantial and statistically significant increase in satisfaction with learning content (from 30% and 34% to 86%, p<0.001) and learning effect (from 65% and 63% to 83%, p<0.05) was observed. Satisfaction ratings stayed on a high level in three subsequent courses with the modules. Qualitative evaluation revealed mostly positive responses, with not a single negative comment regarding the blended learning concept. The results showed that the e-learning tool was appreciated by the students and suggest that learning objective tests can be successfully implemented in blended learning.

  17. Midwifery education and technology enhanced learning: Evaluating online story telling in preregistration midwifery education.

    PubMed

    Scamell, Mandie; Hanley, Thomas

    2018-03-01

    A major issue regarding the implementation of blended learning for preregistration health programmes is the analysis of students' perceptions and attitudes towards their learning. It is the extent of the embedding of Technology Enhanced Learning (TEL) into the higher education curriculum that makes this analysis so vital. This paper reports on the quantitative results of a UK based study that was set up to respond to the apparent disconnect between technology enhanced education provision and reliable student evaluation of this mode of learning. Employing a mixed methods research design, the research described here was carried to develop a reliable and valid evaluation tool to measure acceptability of and satisfaction with a blended learning approach, specifically designed for a preregistration midwifery module offered at level 4. Feasibility testing of 46 completed blended learning evaluation questionnaires - Student Midwife Evaluation of Online Learning Effectiveness (SMEOLE) - using descriptive statistics, reliability and internal consistency tests. Standard deviations and mean scores all followed predicted pattern. Results from the reliability and internal consistency testing confirm the feasibility of SMEOLE as an effective tool for measuring student satisfaction with a blended learning approach to preregistration learning. The analysis presented in this paper suggests that we have been successful in our aim to produce an evaluation tool capable of assessing the quality of technology enhanced, University level learning in Midwifery. This work can provide future benchmarking against which midwifery, and other health, blended learning curriculum planning could be structured and evaluated. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Compilation of Energy Efficient Concepts in Advanced Aircraft Design and Operations. Volume 2. Abstract Data Base

    DTIC Science & Technology

    1980-11-05

    content were studied using a T56 single can combustor rig. Test fuels included single and double ring aromatic types as well as paraffins blended with each...simulated by blending of petroleum based fuels and will be used to conduct research tests required to evolve the technology that may be needed to use...small vertical ° wInglet ° located just inboard of each wingtip; the implementation of supercritlcal aerodynamic wing designs; increase in frequency and

  19. Developing ICT Competency for Thai Teachers through Blended Training

    ERIC Educational Resources Information Center

    Akarawang, Chaiya; Kidrakran, Pachoen; Nuangchalerm, Prasart

    2016-01-01

    The purpose of this study aims to enhance teachers' ICT competency. Three hundred and thirty seven teachers are surveyed through a questionnaire to identify training problems and training needs. Then the blended training model is implemented with teachers. The result showed that it can increase score in cognitive and attitude tests. The post-test…

  20. An Analysis of Factors Affecting Student Perceptions in a Blended Learning Environment

    ERIC Educational Resources Information Center

    Peruso, Florence Mary

    2012-01-01

    The current quantitative study measured the perceptions of students towards online-only learning and towards blended-hybrid learning. Descriptive statistics were implemented to analyze the data from a Likert-type survey, administered to students in degree-seeking programs at an institution of higher learning. A "t"-test and…

  1. Teachers' Perceptions of the Effectiveness of a Blended Learning Approach for ICT Teacher Training

    ERIC Educational Resources Information Center

    Mouzakis, Charalambos

    2008-01-01

    The survey presented in this article examines teachers' perspectives of the effectiveness of the European Pedagogic ICT Licence pilot test in Greece. A total of 51 primary and secondary education teachers participated in the study, immediately following the blended training course. Data were gathered using both quantitative and qualitative…

  2. Effect of first and second generation biodiesel blends on engine performance and emission

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Azad, A. K., E-mail: azad.cqu@gmail.com, E-mail: a.k.azad@cqu.edu.au; Rasul, M. G., E-mail: m.rasul@cqu.edu.au; Bhuiya, M. M. K., E-mail: m.bhuiya@cqu.edu.au

    The biodiesel is a potential source of alternative fuel which can be used at different proportions with diesel fuel. This study experimentally investigated the effect of blend percentage on diesel engine performance and emission using first generation (soybean) and second generation (waste cooking) biodiesel. The characterization of the biodiesel was done according to ASTM and EN standards and compared with ultralow sulfur diesel (ULSD) fuel. A multi-cylinder test bed engine coupled with electromagnetic dynamometer and 5 gas analyzer were used for engine performance and emission test. The investigation was made using B5, B10 and B15 blends for both biodiesels. Themore » study found that brake power (BP) and brake torque (BT) slightly decreases and brake specific fuel consumption (BSFC) slightly increases with an increase in biodiesel blends ratio. Besides, a significant reduction in exhaust emissions (except NO{sub x} emission) was found for both biodiesels compared to ULSD. Soybean biodiesel showed better engine performance and emissions reduction compared with waste cooking biodiesel. However, NO{sub x} emission for B5 waste cooking biodiesel was lower than soybean biodiesel.« less

  3. Cleaner co-combustion of lignite-biomass-waste blends by utilising inhibiting compounds of toxic emissions.

    PubMed

    Skodras, G; Palladas, A; Kaldis, S P; Sakellaropoulos, G P

    2007-04-01

    In this paper, the co-combustion behaviour of coal with wastes and biomass and the related toxic gaseous emissions were investigated. The objective of this work is to add on towards a cleaner co-combustion of lignite-waste-biomass blends by utilizing compounds that could inhibit the formation of toxic pollutants. A series of co-combustion tests was performed in a pilot scale incinerator, and the emissions of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) were measured. The co-combustion behaviour of lignite with olive kernels, MDF and sawdust was studied and the ability of additives such as urea, almond shells and municipal sewage sludge to reduce the PCDD/F emissions was examined. All blends were proven good fuels and reproducible combustion conditions were achieved. The addition of inhibitors prior to combustion showed in some cases, relatively high PCDD/F emissions reduction. Among the inhibitors tested, urea seems to achieve a reduction of PCDD/F emissions for all fuel blends, while an unstable behaviour was observed for the others.

  4. Investigation of in-situ poly(lactic acid)/soy protein concentrate composites: Composite preparation, properties and foam application development

    NASA Astrophysics Data System (ADS)

    Liu, Bo

    2011-12-01

    In this study, soy protein (SP), the residue of oil crushing, was used for preparation of value-added thermoplastics. Novel poly(lactic acid) (PLA)/soy protein concentrate (SPC) blends were investigated and foaming of the resulting blends was developed. PLA/SPC blends were prepared by twin-screw extrusion and test specimens by injection molding. Unlike the practice elsewhere SP was used as a filler in mixing with other polymers, SPC was processed as a plastic component in blending process in this work. Processing SPC as plastic component, water played an important role in terms of the deformability and the morphology of SP thus the properties of the blends. Plasticization of SP, compatibilization of the blends and structure-property relationship of the PLA/SPC blends were studied. In the literature water and glycerol were often used together in preparing SP plastics or plastic blends, but this study found that this traditional combination did not provide the best results in terms of morphology and mechanical properties. Water is only recommended in plasticizing SP in the blends. This study showed water as a plasticizer was a domain factor on control of morphology and properties of PLA/SPC blends. The due to the evaporation of water after extrusion, SP domain lost its deformability thus resulted in in-situ composites. Interconnected SPC phase structure was achieved by control water content in the pre-formulated SPC and SPC content in the blends. A novel dual compatibilization method was developed to improve the properties of PLA/SPC blends. Poly(2-ethyl-2-oxazoline) was used to improve the dispersion of SPC in the blending stage, and polymeric methylene diphenyl diisocyanate was used to improve the interfacial adhesion between SPC and PLA in the subsequent processing. The result showed excellent mechanical properties and improved thermal properties of PLA/SPC blends. Using processing aids is an effective way to decrease processing temperature and thermal degradation of PLA/SPC blends. Interfacial adhesion and chemical blowing agent (CBA) played important roles in extrusion foaming PLA/SPC blends. The interconnected SPC particles provided a convenient passage for gas escape due to the weak adhesion between PLA melt and SPC, especially when CBA content was high. Strong interfacial adhesion is necessary to prevent gas escape and get low density foam at low CBA content. The new findings in this work contribute to the knowledgebase of polymer blends and composites. The findings in this work and implementation of the investigation of preparation and properties of PLA/SP blends set up a framework for future research and development of similar natural polymer blends and will contribute to the commercialization of natural polymer based polymer blends such as starch and sugar beet pulp.

  5. Improving the Cold Temperature Properties of Tallow-Based Methyl Ester Mixtures Using Fractionation, Blending, and Additives

    NASA Astrophysics Data System (ADS)

    Elwell, Caleb

    Beef tallow is a less common feedstock source for biodiesel than soy or canola oil, but it can have economic benefits in comparison to these traditional feedstocks. However, tallow methyl ester (TME) has the major disadvantage of poor cold temperature properties. Cloud point (CP) is an standard industry metric for evaluating the cold temperature performance of biodiesel and is directly related to the thermodynamic properties of the fuel's constituents. TME has a CP of 14.5°C compared with 2.3°C for soy methyl ester (SME) and -8.3°C for canola methyl ester (CME). In this study, three methods were evaluated to reduce the CP of TME: fractionation, blending with SME and CME, and using polymer additives. TME fractionation (i.e. removal of specific methyl ester constituents) was simulated by creating FAME mixtures to match the FAME profiles of fractionated TME. The fractionation yield was found to be highest at the eutectic point of methyl palmitate (MP) and methyl stearate (MS), which was empirically determined to be at a MP/(MP+MS) ratio of approximately 82%. Since unmodified TME has a MP/(MP+MS) ratio of 59%, initially only MS should be removed to produce a ratio closer to the eutectic point to reduce CP and maximize yield. Graphs relating yield (with 4:1 methyl stearate to methyl oleate carryover) to CP were produced to determine the economic viability of this approach. To evaluate the effect of blending TME with other methyl esters, SME and CME were blended with TME at blend ratios of 0 to 100%. Both the SME/TME and CME/TME blends exhibited decreased CPs with increasing levels of SME and CME. Although the CP of the SME/TME blends varied linearly with SME content, the CP of the CME/TME blends varied quadratically with CME content. To evaluate the potential of fuel additives to reduce the CP of TME, 11 different polymer additives were tested. Although all of these additives were specifically marketed to enhance the cold temperature properties of petroleum diesel or biodiesel, only two of the additives had any significant effect on TME CP. The additive formulated by Meat & Livestock Australia (MLA) outperformed Evonik's Viscoplex 10-530. The MLA additive was investigated further and its effect on CP was characterized in pure TME and in CME/TME blends. When mixed in CME/TME blends, the MLA additive had a synergistic effect and produced lower CPs than the addition of mixing MLA in TME and blending CME with TME. To evalulate the cold temperature properties of TME blended with petroleum diesel, CPs of TME/diesel blends from 0 to 100% were measured. The TME/diesel blends were treated with the MLA additives to determine the effects of the additives under these blend conditions. The MLA additive also had a synergistic effect when mixed in TME/diesel blends. Finally, all three of the TME CP reduction methods were evaluated in an economic model to determine the conditions under which each method would be economically viable. Each of the CP reduction methods were compared using a common metric based on the cost of reducing the CP of 1 gallon of finished biodiesel by 1°C (i.e. $/gal/°C). Since the cost of each method is dependent on varying commodity prices, further development of the economic model (which was developed and tested with 2012 prices) to account for stochastic variation in commodity prices is recommended.

  6. Blended shared control utilizing online identification : Regulating grasping forces of a surrogate surgical grasper.

    PubMed

    Stephens, Trevor K; Kong, Nathan J; Dockter, Rodney L; O'Neill, John J; Sweet, Robert M; Kowalewski, Timothy M

    2018-06-01

    Surgical robots are increasingly common, yet routine tasks such as tissue grasping remain potentially harmful with high occurrences of tissue crush injury due to the lack of force feedback from the grasper. This work aims to investigate whether a blended shared control framework which utilizes real-time identification of the object being grasped as part of the feedback may help address the prevalence of tissue crush injury in robotic surgeries. This work tests the proposed shared control framework and tissue identification algorithm on a custom surrogate surgical robotic grasping setup. This scheme utilizes identification of the object being grasped as part of the feedback to regulate to a desired force. The blended shared control is arbitrated between human and an implicit force controller based on a computed confidence in the identification of the grasped object. The online identification is performed using least squares based on a nonlinear tissue model. Testing was performed on five silicone tissue surrogates. Twenty grasps were conducted, with half of the grasps performed under manual control and half of the grasps performed with the proposed blended shared control, to test the efficacy of the control scheme. The identification method resulted in an average of 95% accuracy across all time samples of all tissue grasps using a full leave-grasp-out cross-validation. There was an average convergence time of [Formula: see text] ms across all training grasps for all tissue surrogates. Additionally, there was a reduction in peak forces induced during grasping for all tissue surrogates when applying blended shared control online. The blended shared control using online identification more successfully regulated grasping forces to the desired target force when compared with manual control. The preliminary work on this surrogate setup for surgical grasping merits further investigation on real surgical tools and with real human tissues.

  7. Controlled release of acidic drugs in compendial and physiological hydrogen carbonate buffer from polymer blend-coated oral solid dosage forms.

    PubMed

    Wulff, R; Rappen, G-M; Koziolek, M; Garbacz, G; Leopold, C S

    2015-09-18

    The objective of this study was to investigate the suitability of "Eudragit® RL/Eudragit® L55" (RL/L55) blend coatings for a pH-independent release of acidic drugs. A coating for ketoprofen and naproxen mini tablets was developed showing constant drug release rate under pharmacopeial two-stage test conditions for at least 300 min. To simulate drug release from the mini tablets coated with RL/L55 blends in the gastrointestinal (GI) tract, drug release profiles in Hanks buffer pH 6.8 were recorded and compared with drug release profiles in compendial media. RL/L55 blend coatings showed increased drug permeability in Hanks buffer pH 6.8 compared to phosphate buffer pH 6.8 due to its higher ion concentration. However, drug release rates of acidic drugs were lower in Hanks buffer pH 6.8 because of the lower buffer capacity resulting in reduced drug solubility. Further dissolution tests were performed in Hanks buffer using pH sequences simulating the physiological pH conditions in the GI tract. Drug release from mini tablets coated with an RL/L55 blend (8:1) was insensitive to pH changes of the medium within the pH range of 5.8-7.5. It was concluded that coatings of RL/L55 blends show a high potential for application in coated oral drug delivery systems with a special focus on pH-independent release of acidic drugs. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Students' Perceptions of Blended Learning and its Effectiveness As a Part of Second Year Dental Curriculum

    NASA Astrophysics Data System (ADS)

    Varthis, Spyridon

    The field of dental medical education is one of the most rapidly evolving fields in education. Newer teaching methods are being evaluated and incorporated in dental institutions. One of the promising new methods is the blended learning approach that may involve a "flipped" instructional sequencing, where online instruction precedes the group meeting, allowing for more sophisticated learning through discussion and critical thinking. The author conducted a mixed method, experimental study that focused on second year dental students' perceptions of blended learning and its effectiveness. A sample size of 40 dental students in their second year from a Northeastern Regional Dental School were invited to participate in this study to evaluate a blended learning approach in comparison to a more traditional lecture format. Students who participated in the study, participated in group problem-solving, responded to Likert-type surveys, completed content exams, and were interviewed individually. Based on Likert survey data and interview responses, the participants in the blended learning treatment reported very positive opinions including positive perceptions of the organization, support of meaningful learning and potential merits for use in dental education. There also was evidence that the blended learning group achieved at least as well as the traditional lecture group, and excelled on certain content test items. The results of this study support the conclusion that blended instruction promotes active, in-depth and self-regulated learning. During blended learning, students set standards or goals regarding their learning, evaluate their progress toward these goals, and then adapt and regulate their cognition, motivation, and behavior in order to accomplish their goals. Overall, the results of this research on blended learning, including the use of problem-based learning in group discussions, supports the merits of incorporating blended earning in dental education curricula.

  9. Swelling and tribological properties of melt-mixed fluoroelastomer/nitrile rubber blends under crude oil

    NASA Astrophysics Data System (ADS)

    Tagelsir, Yasin; Li, San-Xi; Lv, Xiaoren; Wang, Shijie; Wang, Song; Osman, Zeinab

    2018-01-01

    The melt-mixed fluoroelastomer (FKM)/ nitrile rubber (NBR) blends of (90/10, 80/20, 70/30, 60/40 and 50/50) ratios with same hardness were prepared, and their swelling and tribological properties under crude oil were investigated for the purpose of developing high performance cost-effective elastomers meeting requirement of oil extraction progressive cavity pump stator. Differential scanning calorimetry confirmed compatible blend system for all blends. Field emission scanning electron microscopy (FE-SEM) showed co-continuous morphology of 200-400 nm phase size for all blends, expect FKM/NBR (90/10) which exhibited partially continuous phase morphology of 100-250 nm phase size. The results of swelling and linear wear tests under crude oil indicated that swelling percentage, coefficient of friction and specific wear rate of FKM/NBR blends were much better than NBR, with FKM/NBR (90/10 and 80/20) showing swelling percentage and specific wear rate very close to FKM. Attenuated total reflectance-Fourier transform infrared spectroscopy disclosed that fracture of macromolecular chains was the main mechanochemical effect of unswollen and swollen worn surfaces, in addition to oxygenated degradation detected with increasing NBR ratio in the blends. The fracture of macromolecular chains resulted in slight fatigue wear mechanism, which was also confirmed by FE-SEM of the worn surfaces.

  10. [Online endpoint detection algorithm for blending process of Chinese materia medica].

    PubMed

    Lin, Zhao-Zhou; Yang, Chan; Xu, Bing; Shi, Xin-Yuan; Zhang, Zhi-Qiang; Fu, Jing; Qiao, Yan-Jiang

    2017-03-01

    Blending process, which is an essential part of the pharmaceutical preparation, has a direct influence on the homogeneity and stability of solid dosage forms. With the official release of Guidance for Industry PAT, online process analysis techniques have been more and more reported in the applications in blending process, but the research on endpoint detection algorithm is still in the initial stage. By progressively increasing the window size of moving block standard deviation (MBSD), a novel endpoint detection algorithm was proposed to extend the plain MBSD from off-line scenario to online scenario and used to determine the endpoint in the blending process of Chinese medicine dispensing granules. By online learning of window size tuning, the status changes of the materials in blending process were reflected in the calculation of standard deviation in a real-time manner. The proposed method was separately tested in the blending processes of dextrin and three other extracts of traditional Chinese medicine. All of the results have shown that as compared with traditional MBSD method, the window size changes according to the proposed MBSD method (progressively increasing the window size) could more clearly reflect the status changes of the materials in blending process, so it is suitable for online application. Copyright© by the Chinese Pharmaceutical Association.

  11. Performance of blend sign in predicting hematoma expansion in intracerebral hemorrhage: A meta-analysis.

    PubMed

    Yu, Zhiyuan; Zheng, Jun; Guo, Rui; Ma, Lu; Li, Mou; Wang, Xiaoze; Lin, Sen; Li, Hao; You, Chao

    2017-12-01

    Hematoma expansion is independently associated with poor outcome in intracerebral hemorrhage (ICH). Blend sign is a simple predictor for hematoma expansion on non-contrast computed tomography. However, its accuracy for predicting hematoma expansion is inconsistent in previous studies. This meta-analysis is aimed to systematically assess the performance of blend sign in predicting hematoma expansion in ICH. A systematic literature search was conducted. Original studies about predictive accuracy of blend sign for hematoma expansion in ICH were included. Pooled sensitivity, specificity, positive and negative likelihood ratios were calculated. Summary receiver operating characteristics curve was constructed. Publication bias was assessed by Deeks' funnel plot asymmetry test. A total of 5 studies with 2248 patients were included in this meta-analysis. The pooled sensitivity, specificity, positive and negative likelihood ratios of blend sign for predicting hematoma expansion were 0.28, 0.92, 3.4 and 0.78, respectively. The area under the curve (AUC) was 0.85. No significant publication bias was found. This meta-analysis demonstrates that blend sign is a useful predictor with high specificity for hematoma expansion in ICH. Further studies with larger sample size are still necessary to verify the accuracy of blend sign for predicting hematoma expansion. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Blended learning is an effective strategy for acquiring competence in public health biostatistics.

    PubMed

    Milic, Natasa; Masic, Srdjan; Bjegovic-Mikanovic, Vesna; Trajkovic, Goran; Marinkovic, Jelena; Milin-Lazovic, Jelena; Bukumiric, Zoran; Savic, Marko; Cirkovic, Andja; Gajic, Milan; Stanisavljevic, Dejana

    2018-04-01

    We sought to determine whether blended learning is an effective strategy for acquiring competence in public health biostatistics. The trial was conducted with 69 Masters' students of public health attending the School of Public Health at University of Belgrade. Students were exposed to the traditional and blended learning styles. Blended learning included a combination of face-to-face and distance learning methodologies integrated into a single course. Curriculum development was guided by competencies as suggested by the Association of Schools of Public Health in the European Region (ASPHER). Teaching methods were compared according to the final competence score. Forty-four students were enrolled in the traditional method of education delivery, and 25 to the blended learning format. Mean exam scores for the blended learning group were higher than for the on-site group for both the final statistics score (89.65 ± 6.93 vs. 78.21 ± 13.26; p < 0.001) and knowledge test score (35.89 ± 3.66 vs. 22.56 ± 7.12; p < 0.001), with estimated large effect size (d > 0.8). A blended learning approach is an attractive and effective way of acquiring biostatistics competence for Masters of Public Health (MPH) graduate students.

  13. Synthetic aggregate compositions derived from spent bed materials from fluidized bed combustion and fly ash

    DOEpatents

    Boyle, Michael J.

    1994-01-01

    Cementitious compositions useful as lightweight aggregates are formed from a blend of spent bed material from fluidized bed combustion and fly ash. The proportions of the blend are chosen so that ensuing reactions eliminate undesirable constituents. The blend is then mixed with water and formed into a shaped article. The shaped article is preferably either a pellet or a "brick" shape that is later crushed. The shaped articles are cured at ambient temperature while saturated with water. It has been found that if used sufficiently, the resulting aggregate will exhibit minimal dimensional change over time. The aggregate can be certified by also forming standardized test shapes, e.g., cylinders while forming the shaped articles and measuring the properties of the test shapes using standardized techniques including X-ray diffraction.

  14. Novel bio-based and biodegradable polymer blends

    NASA Astrophysics Data System (ADS)

    Yang, Shengzhe

    Most plastic materials, including high performance thermoplastics and thermosets are produced entirely from petroleum-based products. The volatility of the natural oil markets and the increasing cost of petroleum have led to a push to reduce the dependence on petroleum products. Together with an increase in environmental awareness, this has promoted the use of alternative, biorenewable, environmentally-friendly products, such as biomass. The growing interest in replacing petroleum-based products by inexpensive, renewable, natural materials is important for sustainable development into the future and will have a significant impact on the polymer industry and the environment. This thesis involved characterization and development of two series of novel bio-based polymer blends, namely polyhydroxyalkanoate (PHA)/polyamide (PA) and poly(lactic acid) (PLA)/soy protein. Blends with different concentrations and compatible microstructures were prepared using twin-screw extruder. For PHA/PA blends, the poor mechanical properties of PHA improved significantly with an excellent combination of strength, stiffness and toughness by adding PA. Furthermore, the effect of blending on the viscoelastic properties has been investigated using small-amplitude oscillatory shear flow experiments as a function of blend composition and angular frequency. The elastic shear modulus (G‧) and complex viscosity of the blends increased significantly with increasing the concentration of PHA. Blending PLA with soy protein aims at reducing production cost, as well as accelerating the biodegradation rate in soil medium. In this work, the mechanical, thermal and morphological properties of the blends were investigated using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and tensile tests.

  15. BioBlend: automating pipeline analyses within Galaxy and CloudMan.

    PubMed

    Sloggett, Clare; Goonasekera, Nuwan; Afgan, Enis

    2013-07-01

    We present BioBlend, a unified API in a high-level language (python) that wraps the functionality of Galaxy and CloudMan APIs. BioBlend makes it easy for bioinformaticians to automate end-to-end large data analysis, from scratch, in a way that is highly accessible to collaborators, by allowing them to both provide the required infrastructure and automate complex analyses over large datasets within the familiar Galaxy environment. http://bioblend.readthedocs.org/. Automated installation of BioBlend is available via PyPI (e.g. pip install bioblend). Alternatively, the source code is available from the GitHub repository (https://github.com/afgane/bioblend) under the MIT open source license. The library has been tested and is working on Linux, Macintosh and Windows-based systems.

  16. Microscopic understanding of the complex polymer dynamics in a blend —A molecular-dynamics simulation study

    NASA Astrophysics Data System (ADS)

    Diddens, D.; Brodeck, M.; Heuer, A.

    2011-09-01

    Within polymer blends composed of two species with largely different glass transition temperatures like PEO/PMMA, the dynamics of the fast PEO component is severely affected by the rather immobile PMMA, reflected by a breakdown of the typical Rouse scaling. The phenomenological random Rouse model (RRM), in which each monomer has an individual mobility obeying a broad log-normal distribution, has been applied to these blends. Using a newly developed method, we extract the distribution of friction coefficients from MD simulations of a PEO/PMMA blend, thereby testing the RRM explicitly. In our simulations we observe that the distribution is much narrower than expected from the RRM. Here, rather, the presence of additional forward-backward correlations of intermolecular origin is responsible for the anomalous PEO behavior.

  17. Friction and wear study of NR/SBR blends with Si3N4Filler

    NASA Astrophysics Data System (ADS)

    GaneshKumar, A.; Balaganesan, G.; Sivakumar, M. S.

    2018-04-01

    The aim of this paper is to investigate mechanical and frictional properties of natural rubber/styrene butadiene rubber (NR/SBR) blends with and without silicon nitride (Si3N4) filler. The rubber is surface modified by silane coupling agent (Si-69) for enhancing hydrophobic property. The Si3N4of percentage 0 1, 3, 5 and 7, is incorporated into NR/SBR rubber compounds with 20% precipitated silica. The specimens with and without fillers are prepared as per standard for tensile and friction testing. Fourier transform infrared (FTIR) spectroscopy test is conducted and it is inferred that the coupling agent is covalently bonded on the surface of Si3N4 particles and an organic coating layer is formed. The co-efficient of friction and specific wear rate of NR/SBR blends are examined using an in-house built friction tester in a disc-on-plate (DOP) configuration. The specimens are tested to find coefficient of friction (COF) against steel grip antiskid plate under dry, mud, wet and oil environmental conditions. It is found that the increase in tensile strength and modulus at low percentage of Si3N4 dispersion. It is also observed that increase in sliding friction co-efficient and decrease in wear rate for 1% of Si3N4 dispersion in NR/SBR blends. The friction tested surfaces are inspected using Scanning Electron Microscope (SEM) and 3D non contact surface profiler.

  18. Thermal Stability Results of a Fischer-Tropsch Fuel With Various Blends of Aromatic Solution

    NASA Technical Reports Server (NTRS)

    Lindsey, Jennifer; Klettlinger, Suder

    2013-01-01

    Fischer-Tropsch (F-T) jet fuel composition differs from petroleum-based, conventional commercial jet fuel because of differences in feedstock and production methodology. F-T fuel typically has a lower aromatic and sulfur content and consists primarily of iso and normal paraffins. The ASTM D3241 specification for Jet Fuel Thermal Oxidation Test (JFTOT) break point testing method was used to test the breakpoint of a baseline commercial grade F-T jet fuel, and various blends of this F-T fuel with an aromatic solution. The goal of this research is to determine the effect of aromatic content on the thermal stability of F-T fuel. The testing completed in this report was supported by the NASA Fundamental Aeronautics Subsonic Fixed Wing Project. Two different aromatic content fuels from Rentech, as well as these fuels with added aromatic blend were analyzed for thermal stability using the JFTOT method. Preliminary results indicate a reduction in thermal stability occurs upon increasing the aromatic content to 10% by adding an aromatic blend to the neat fuel. These results do not specify a failure based on pressure drop, but only on tube color. It is unclear whether tube color correlates to more deposition on the tube surface or not. Further research is necessary in order to determine if these failures are true failures based on tube color. Research using ellipsometry to determine tube deposit thickness rather than color will be continued in follow-up of this study.

  19. Antibacterial, antifungal, and antiviral effects of three essential oil blends.

    PubMed

    Brochot, Amandine; Guilbot, Angèle; Haddioui, Laïla; Roques, Christine

    2017-08-01

    New agents that are effective against common pathogens are needed particularly for those resistant to conventional antimicrobial agents. Essential oils (EOs) are known for their antimicrobial activity. Using the broth microdilution method, we showed that (1) two unique blends of Cinnamomum zeylanicum, Daucus carota, Eucalyptus globulus and Rosmarinus officinalis EOs (AB1 and AB2; cinnamon EOs from two different suppliers) were active against the fourteen Gram-positive and -negative bacteria strains tested, including some antibiotic-resistant strains. Minimal inhibitory concentrations (MICs) ranged from 0.01% to 3% v/v with minimal bactericidal concentrations from <0.01% to 6.00% v/v; (2) a blend of Cinnamomum zeylanicum, Daucus carota, Syzygium aromaticum, Origanum vulgare EOs was antifungal to the six Candida strains tested, with MICs ranging from 0.01% to 0.05% v/v with minimal fungicidal concentrations from 0.02% to 0.05% v/v. Blend AB1 was also effective against H1N1 and HSV1 viruses. With this dual activity, against H1N1 and against S. aureus and S. pneumoniae notably, AB1 may be interesting to treat influenza and postinfluenza bacterial pneumonia infections. These blends could be very useful in clinical practice to combat common infections including those caused by microorganisms resistant to antimicrobial drugs. © 2017 The Authors. MicrobiologyOpen published by John Wiley & Sons Ltd.

  20. Experimental investigation on flexure and impact properties of injection molded polypropylene-nylon 6-glass fiber polymer composites

    NASA Astrophysics Data System (ADS)

    Nuruzzaman, D. M.; Kusaseh, N. M.; Chowdhury, M. A.; Rahman, N. A. N. A.; Oumer, A. N.; Fatchurrohman, N.; Iqbal, A. K. M. A.; Ismail, N. M.

    2018-04-01

    In this research study, glass fiber (GF) reinforced polypropylene (PP)-nylon 6 (PA6) polymer blend composites were prepared using injection molding process. Specimens of four different compositions such as 80%PP+20%PA6, 80%PP+18%PA6+2%GF, 80%PP+16%PA6+4%GF and 80%PP+14%PA6+6%GF were prepared. In the injection molding process, suitable process parameters were selected depending on the type of composite specimen in producing defects free dog bone shaped specimens. Flexure and impact tests were carried out according to ASTM standard. The important flexure properties such as flexural modulus, flexural yield strength, flexural strength and flexural strain were investigated. The obtained results revealed that flexural modulus of 80%PP+20%PA6 polymer blend is the lowest and the polymer blend composite shows steadily improved modulus as the glass fiber content is increased. Results also showed that flexural strength of pure polymer blend is the lowest but it improves gradually when the glass fiber content is increased. Impact test results revealed that impact strength of 80%PP+20%PA6 polymer blend is the highest whereas all the composites show reduced impact strength or toughness. It is noticed that 80%PP+14%PA6+6%GF composite exhibits the lowest impact strength.

  1. High calcium fly ash geopolymer stabilized lateritic soil and granulated blast furnace slag blends as a pavement base material.

    PubMed

    Phummiphan, Itthikorn; Horpibulsuk, Suksun; Rachan, Runglawan; Arulrajah, Arul; Shen, Shui-Long; Chindaprasirt, Prinya

    2018-01-05

    Granulated Blast Furnace Slag (GBFS) was used as a replacement material in marginal lateritic soil (LS) while class C Fly Ash (FA) was used as a precursor for the geopolymerization process to develop a low-carbon pavement base material at ambient temperature. Unconfined Compression Strength (UCS) tests were performed to investigate the strength development of geopolymer stabilized LS/GBFS blends. Scanning Electron Microscopy and X-ray Diffraction analysis were undertaken to examine the role of the various influencing factors on UCS development. The influencing factors studied included GBFS content, Na 2 SiO 3 :NaOH ratio (NS:NH) and curing time. The 7-day soaked UCS of FA geopolymer stabilized LS/GBFS blends at various NS:NH ratios tested was found to satisfy the specifications of the Thailand national road authorities. The GBFS replacement was found to be insignificant for the improvement of the UCS of FA geopolymer stabilized LS/GBFS blends at low NS:NH ratio of 50:50. Microstructural analysis indicated the coexistence of Calcium Silicate Hydrate (CSH) and Sodium Alumino Silicate Hydrate products in FA geopolymer stabilized LS/GBFS blends. This research enables GBFS, which is traditionally considered as a waste material, to be used as a replacement and partially reactive material in FA geopolymer pavement applications. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Shetty, G. Rajesha; Kumar, R. Madhu; Rao, B. Lakshmeesha

    In this work, the structural and mechanical stability of silk fibroin/Hydroxypropylmethyl cellulose (SF-HPMC) blend films were characterized by X-ray diffraction (XRD) and Universal Testing Machine (UTM). The results indicate that with the introduction of HPMC, the interactions between SF and HPMC results in improved crystallite size and increase in mechanical properties. The blend film obtained is more flexible compared to pure SF film.

  3. Effects of Traditional, Blended and E-Learning on Students' Achievement in Higher Education

    ERIC Educational Resources Information Center

    Al-Qahtani, Awadh A. Y.; Higgins, S. E.

    2013-01-01

    The study investigates the effect of e-learning, blended learning and classroom learning on students' achievement. Two experimental groups together with a control group from Umm Al-Qura University in Saudi Arabia were identified randomly. To assess students' achievement in the different groups, pre- and post-achievement tests were used. The…

  4. The Development of Instructional Materials E-Learning Based on Blended Learning

    ERIC Educational Resources Information Center

    Kristanto, Andi; Mustaji; Mariono, Andi

    2017-01-01

    The use of e-learning is becoming the global issue now. In an educational field, there are many institutions already use it. The study very important aimed to test the feasibility and effectiveness the development of instructional materials e-learning based on the blended learning in audio/radio media development course. The background laid behind…

  5. 40 CFR 80.49 - Fuels to be used in augmenting the complex emission model through vehicle testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... shall be within the blending tolerances defined in this paragraph (a)(4) relative to the values... be within the blending tolerances defined in this paragraph (c) relative to the values specified in... “candidate” level of the parameter shall refer to the most extreme value of the parameter, relative to...

  6. Facile fabrication of HDPE-g-MA/nanodiamond nanocomposites via one-step reactive blending.

    PubMed

    Song, Ping'an; Yu, Youming; Wu, Qiang; Fu, Shenyuan

    2012-06-29

    In this letter, nanocomposites based on maleic anhydride grafted high density polyethylene (HDPE-g-MA) and amine-functionalized nanodiamond (ND) were fabricated via one-step reactive melt-blending, generating a homogeneous dispersion of ND, as evidenced by transmission electron microscope observations. Thermal analysis results suggest that addition of ND does not affect significantly thermal stability of polymer matrix in nitrogen. However, it was interestingly found that incorporating pure ND decreases the thermal oxidation degradation stability temperature, but blending amino-functionalized ND via reactive processing significantly enhances it of HDPE in air condition. Most importantly, cone tests revealed that both ND additives and reactive blending greatly reduce the heat release rate of HDPE. The results suggest that ND has a potential application as flame retardant alternative for polymers. Tensile results show that adding ND considerably enhances Young's modulus, and reactive blending leads to further improvement in Young's modulus while hardly reducing the elongation at break of HDPE.

  7. Facile fabrication of HDPE-g-MA/nanodiamond nanocomposites via one-step reactive blending

    PubMed Central

    2012-01-01

    In this letter, nanocomposites based on maleic anhydride grafted high density polyethylene (HDPE-g-MA) and amine-functionalized nanodiamond (ND) were fabricated via one-step reactive melt-blending, generating a homogeneous dispersion of ND, as evidenced by transmission electron microscope observations. Thermal analysis results suggest that addition of ND does not affect significantly thermal stability of polymer matrix in nitrogen. However, it was interestingly found that incorporating pure ND decreases the thermal oxidation degradation stability temperature, but blending amino-functionalized ND via reactive processing significantly enhances it of HDPE in air condition. Most importantly, cone tests revealed that both ND additives and reactive blending greatly reduce the heat release rate of HDPE. The results suggest that ND has a potential application as flame retardant alternative for polymers. Tensile results show that adding ND considerably enhances Young’s modulus, and reactive blending leads to further improvement in Young’s modulus while hardly reducing the elongation at break of HDPE. PMID:22747773

  8. Comparison of the effect of lecture and blended teaching methods on students’ learning and satisfaction

    PubMed Central

    SADEGHI, ROYA; SEDAGHAT, MOHAMMAD MEHDI; SHA AHMADI, FARAMARZ

    2014-01-01

    Introduction: Blended learning, a new approach in educational planning, is defined as an applying more than one method, strategy, technique or media in education. Todays, due to the development of infrastructure of Internet networks and the access of most of the students, the Internet can be utilized along with traditional and conventional methods of training. The aim of this study was to compare the students’ learning and satisfaction in combination of lecture and e-learning with conventional lecture methods. Methods: This quasi-experimental study is conducted among the sophomore students of Public Health School, Tehran University of Medical Science in 2012-2013. Four classes of the school are randomly selected and are divided into two groups. Education in two classes (45 students) was in the form of lecture method and in the other two classes (48 students) was blended method with e-Learning and lecture methods. The students’ knowledge about tuberculosis in two groups was collected and measured by using pre and post-test. This step has been done by sending self-reported electronic questionnaires to the students' email addresses through Google Document software. At the end of educational programs, students' satisfaction and comments about two methods were also collected by questionnaires. Statistical tests such as descriptive methods, paired t-test, independent t-test and ANOVA were done through the SPSS 14 software, and p≤0.05 was considered as significant difference. Results: The mean scores of the lecture and blended groups were 13.18±1.37 and 13.35±1.36, respectively; the difference between the pre-test scores of the two groups was not statistically significant (p=0.535). Knowledge scores increased in both groups after training, and the mean and standard deviation of knowledge scores of the lectures and combined groups were 16.51±0.69 and 16.18±1.06, respectively. The difference between the post-test scores of the two groups was not statistically significant (p=0.112). Students’ satisfaction in blended learning method was higher than lecture method. Conclusion: The results revealed that the blended method is effective in increasing the students' learning rate. E-learning can be used to teach some courses and might be considered as economic aspects. Since in universities of medical sciences in the country, the majority of students have access to the Internet and email address, using e-learning could be used as a supplement to traditional teaching methods or sometimes as educational alternative method because this method of teaching increases the students’ knowledge, satisfaction and attention. PMID:25512938

  9. Comparison of the effect of lecture and blended teaching methods on students' learning and satisfaction.

    PubMed

    Sadeghi, Roya; Sedaghat, Mohammad Mehdi; Sha Ahmadi, Faramarz

    2014-10-01

    Blended learning, a new approach in educational planning, is defined as an applying more than one method, strategy, technique or media in education. Todays, due to the development of infrastructure of Internet networks and the access of most of the students, the Internet can be utilized along with traditional and conventional methods of training. The aim of this study was to compare the students' learning and satisfaction in combination of lecture and e-learning with conventional lecture methods. This quasi-experimental study is conducted among the sophomore students of Public Health School, Tehran University of Medical Science in 2012-2013. Four classes of the school are randomly selected and are divided into two groups. Education in two classes (45 students) was in the form of lecture method and in the other two classes (48 students) was blended method with e-Learning and lecture methods. The students' knowledge about tuberculosis in two groups was collected and measured by using pre and post-test. This step has been done by sending self-reported electronic questionnaires to the students' email addresses through Google Document software. At the end of educational programs, students' satisfaction and comments about two methods were also collected by questionnaires. Statistical tests such as descriptive methods, paired t-test, independent t-test and ANOVA were done through the SPSS 14 software, and p≤0.05 was considered as significant difference. The mean scores of the lecture and blended groups were 13.18±1.37 and 13.35±1.36, respectively; the difference between the pre-test scores of the two groups was not statistically significant (p=0.535). Knowledge scores increased in both groups after training, and the mean and standard deviation of knowledge scores of the lectures and combined groups were 16.51±0.69 and 16.18±1.06, respectively. The difference between the post-test scores of the two groups was not statistically significant (p=0.112). Students' satisfaction in blended learning method was higher than lecture method. The results revealed that the blended method is effective in increasing the students' learning rate. E-learning can be used to teach some courses and might be considered as economic aspects. Since in universities of medical sciences in the country, the majority of students have access to the Internet and email address, using e-learning could be used as a supplement to traditional teaching methods or sometimes as educational alternative method because this method of teaching increases the students' knowledge, satisfaction and attention.

  10. Study of biodegradable polylactide/poly(butylene adipate-co-terephthalate) blends.

    PubMed

    Jiang, Long; Wolcott, Michael P; Zhang, Jinwen

    2006-01-01

    Both polylactide (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) are biodegradable polymers. They are thermoplastics which can be processed using most conventional polymer processing methods. PLA is high in strength and modulus (63 MPa and 3.4 GPa, respectively) but brittle (strain at break 3.8%) while PBAT is flexible and tough (strain at break approximately 710%). In view of their complementary properties, blending PLA with PBAT becomes a natural choice to improve PLA properties without compromising its biodegradability. In this study, PLA and PBAT were melt blended using a twin screw extruder. Melt elasticity and viscosity of the blends increased with the concentration of PBAT. Crystallization of the PLA component, phase morphology of the blend, mechanical properties, and toughening mechanism were investigated. The blend comprised an immiscible, two-phase system with the PBAT evenly dispersed in the form of approximately 300 nm domains within the PLA matrix. The PBAT component accelerated the crystallization rate of PLA but had little effect on its final degree of crystallinity. With the increase in PBAT content (5-20 wt %), the blend showed decreased tensile strength and modulus; however, elongation and toughness were dramatically increased. With the addition of PBAT, the failure mode changed from brittle fracture of the neat PLA to ductile fracture of the blend as demonstrated by tensile test and scanning electron microcopy (SEM) micrographs. Debonding between the PLA and PBAT domains induced large plastic deformation in PLA matrix ligaments.

  11. A blended design in acute care training: similar learning results, less training costs compared with a traditional format.

    PubMed

    Dankbaar, Mary E W; Storm, Diana J; Teeuwen, Irene C; Schuit, Stephanie C E

    2014-09-01

    Introduction There is a demand for more attractive and efficient training programmes in postgraduate health care training. This retrospective study aims to show the effectiveness of a blended versus traditional face-to-face training design. For nurses in postgraduate Acute and Intensive Care training, the effectiveness of a blended course design was compared with a traditional design. Methods In a first pilot study 57 students took a traditional course (2-h lecture and 2-h workshop) and 46 students took a blended course (2-h lecture and 2-h online self-study material). Test results were compared for both groups. After positive results in the pilot study, the design was replicated for the complete programme in Acute and Intensive Care. Now 16 students followed the traditional programme (11 days face-to-face education) and 31 students did the blended programme (7 days face-to-face and 40 h online self-study). An evaluation was done after the pilot and course costs were calculated. Results Results show that the traditional and blended groups were similar regarding the main characteristics and did not differ in learning results for both the pilot and the complete programme. Student evaluations of both designs were positive; however, the blended group were more confident that they had achieved the learning objectives. Training costs were reduced substantially. Conclusion The blended training design offers an effective and attractive training solution, leading to a significant reduction in costs.

  12. Investigation of Atomization and Combustion Performance of Renewable Biofuels and the Effects of Ethanol Blending in Biodiesel

    NASA Astrophysics Data System (ADS)

    Silver, Adam Gregory

    This thesis presents results from an experimental investigation of the macroscopic and microscopic atomization and combustion behavior of B99 biodiesel, ethanol, B99-ethanol blends, methanol, and an F-76-Algae biodiesel blend. In addition, conventional F-76 and Diesel #2 sprays were characterized as a base case to compare with. The physical properties and chemical composition of each fuel were measured in order to characterize and predict atomization performance. A variety of B99-ethanol fuel blends were used which demonstrate a tradeoff between lower density, surface tension, and viscosity with a decrease in the air to liquid ratio. A plain jet air-blast atomizer was used for both non-reacting and reacting tests. The flow rates for the alternative fuels were set by matching the power input provided by the baseline fossil fuels in order to simulate use as a drop in replacement. For this study, phase Doppler interferometry is employed to gain information on drop size, SMD, velocity, and volume flux distribution across the spray plume. A high speed camera is used to gather high speed cinematography of the sprays for observing breakup characteristics and providing additional insight. Reacting flow tests captured NOx, CO, and UHC emissions along with high speed footage used to predict soot levels based on flame luminosity. The results illustrate how the fuel type impacts the atomization and spray characteristics. The air-blast atomizer resulted in similar atomization performance among the DF2, F-76, and the F-76/Algae blend. While methanol and ethanol are not suitable candidates for this air-blast configuration and B99 produces significantly larger droplets, the addition of ethanol decreased drop sizes for all B99-ethanol blends by approximately 5 microns. In regards to reacting conditions, increased ethanol blending to B99 consistently lowered NOx emissions while decreasing combustion efficiency. Overall, lower NOx and CO emissions were achieved with the fuel blends than for conventional diesels, while the neat biofuels emitted overall less NOx per CO than the baseline fuels. This research clearly demonstrated that blends of two renewable fuels (B99 and ethanol improved (1) atomization and (2) emissions performance for the burner studied when compared to the baseline fossil fuels DF2 and F-76.

  13. Properties investigation of sulfonated poly(ether ether ketone)/polyacrylonitrile acid-base blend membrane for vanadium redox flow battery application.

    PubMed

    Li, Zhaohua; Dai, Wenjing; Yu, Lihong; Liu, Le; Xi, Jingyu; Qiu, Xinping; Chen, Liquan

    2014-11-12

    Acid-base blend membrane prepared from sulfonated poly(ether ether ketone) (SPEEK) and polyacrylonitrile (PAN) was detailedly evaluated for vanadium redox flow battery (VRFB) application. SPEEK/PAN blend membrane exhibited dense and homogeneous cross-section morphology as scanning electron microscopy and energy-dispersive X-ray spectroscopy images show. The acid-base interaction of ionic cross-linking and hydrogen bonding between SPEEK and PAN could effectively reduce water uptake, swelling ratio, and vanadium ion permeability, and improve the performance and stability of blend membrane. Because of the good balance of proton conductivity and vanadium ion permeability, blend membrane with 20 wt % PAN (S/PAN-20%) showed higher Coulombic efficiency (96.2% vs 91.1%) and energy efficiency (83.5% vs 78.4%) than Nafion 117 membrane at current density of 80 mA cm(-2) when they were used in VRFB single cell. Besides, S/PAN-20% membrane kept a stable performance during 150 cycles at current density of 80 mA cm(-2) in the cycle life test. Hence the SPEEK/PAN acid-base blend membrane could be used as promising candidate for VRFB application.

  14. Development of Antimicrobial Packaging Film Made from Poly(Lactic Acid) Incorporating Titanium Dioxide and Silver Nanoparticles.

    PubMed

    Li, Wenhui; Zhang, Cheng; Chi, Hai; Li, Lin; Lan, Tianqing; Han, Peng; Chen, Haiyan; Qin, Yuyue

    2017-07-13

    Polylactide (PLA)/nano-TiO₂ and PLA/nano-TiO₂/nano-Ag blends films were prepared by a solvent volatilization method. Compared to pure PLA film, the nano-blend films have low water vapor permeability (WVP) and a poor transparency. With the increase of the NPs in the PLA, the tensile strength (TS) and elastic modulus (EM) decreased, while the elongation at break (ε) increased. SEM analysis indicated a rougher cross-section of the nano-blend films. According to the FTIR analysis, no new chemical bonds were formed in the nano-blend films. By using DSC to examine the crystallization and melting behavior, the result shows that the NPs have no effect on the glass transition (T g ) and melting temperature (T m ), but they caused an increase on the cold crystallization (T c) and crystallinity ( X c ). TGA results show that the addition of nanoparticles significantly improved the thermal stability. The PLA nano-blend films show a good antimicrobial activity against. E. coli and Listeria monocytogenes . Most important, we carried out migration tests, and verified that the release of NPs from the nano-blend films was within the standard limits.

  15. Regulated and unregulated emissions from a diesel engine fueled with diesel fuel blended with diethyl adipate

    NASA Astrophysics Data System (ADS)

    Zhu, Ruijun; Cheung, C. S.; Huang, Zuohua; Wang, Xibin

    2011-04-01

    Experiments were carried out on a four-cylinder direct-injection diesel engine operating on Euro V diesel fuel blended with diethyl adipate (DEA). The blended fuels contain 8.1%, 16.4%, 25% and 33.8% by volume fraction of DEA, corresponding to 3%, 6%, 9% and 12% by mass of oxygen in the blends. The engine performance and exhaust gas emissions of the different fuels were investigated at five engine loads at a steady speed of 1800 rev/min. The results indicated an increase of brake specific fuel consumption and brake thermal efficiency when the engine was fueled with the blended fuels. In comparison with diesel fuel, the blended fuels resulted in an increase in hydrocarbon (HC) and carbon monoxide (CO), but a decrease in particulate mass concentrations. The nitrogen oxides (NO x) emission experienced a slight variation among the test fuels. In regard to the unregulated gaseous emissions, formaldehyde and acetaldehyde increased, while 1,3-butadiene, ethene, ethyne, propylene and BTX (benzene, toluene and xylene) in general decreased. A diesel oxidation catalyst (DOC) was found to reduce significantly most of the investigated unregulated pollutants when the exhaust gas temperature was sufficiently high.

  16. The effect of azeotropism on combustion characteristics of blended fuel pool fire.

    PubMed

    Ding, Yanming; Wang, Changjian; Lu, Shouxiang

    2014-04-30

    The effect of azeotropism on combustion characteristics of blended fuel pool fire was experimentally studied in an open fire test space of State Key Laboratory of Fire Science. A 30 cm × 30 cm square pool filled with n-heptane and ethanol blended fuel was employed. Flame images, burning rate and temperature distribution were collected and recorded in the whole combustion process. Results show that azeotropism obviously dominates the combustion behavior of n-heptane/ethanol blended fuel pool fire. The combustion process after ignition exhibits four typical stages: initial development, azeotropic burning, single-component burning and decay stage. Azeotropism appears when temperature of fuel surface reaches azeotropic point and blended fuel burns at azeotropic ratio. Compared with individual pure fuel, the effect of azeotropism on main fire parameters, such as flame height, burning rate, flame puffing frequency and centerline temperature were analyzed. Burning rate and centerline temperature of blended fuel are higher than that of individual pure fuel respectively at azeotropic burning stage, and flame puffing frequency follows the empirical formula between Strouhal and Froude number for pure fuel. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Variation in and responses to brood pheromone of the honey bee (Apis mellifera L.).

    PubMed

    Metz, Bradley N; Pankiw, Tanya; Tichy, Shane E; Aronstein, Katherine A; Crewe, Robin M

    2010-04-01

    The 10 fatty acid ester components of brood pheromone were extracted from larvae of different populations of USA and South African honey bees and subjected to gas chromatography-mass spectrometry quantitative analysis. Extractable amounts of brood pheromone were not significantly different by larval population; however, differences in the proportions of components enabled us to classify larval population of 77% of samples correctly by discriminant analysis. Honeybee releaser and primer pheromone responses to USA, Africanized and-European pheromone blends were tested. Texas-Africanized and Georgia-European colonies responded with a significantly greater ratio of returning pollen foragers when treated with a blend from the same population than from a different population. There was a significant interaction of pheromone blend by adult population source among Georgia-European bees for modulation of sucrose response threshold, a primer response. Brood pheromone blend variation interacted with population for pollen foraging response of colonies, suggesting a self recognition cue for this pheromone releaser behavior. An interaction of pheromone blend and population for priming sucrose response thresholds among workers within the first week of adult life suggested a more complex interplay of genotype, ontogeny, and pheromone blend.

  18. Process analytical technology in continuous manufacturing of a commercial pharmaceutical product.

    PubMed

    Vargas, Jenny M; Nielsen, Sarah; Cárdenas, Vanessa; Gonzalez, Anthony; Aymat, Efrain Y; Almodovar, Elvin; Classe, Gustavo; Colón, Yleana; Sanchez, Eric; Romañach, Rodolfo J

    2018-03-01

    The implementation of process analytical technology and continuous manufacturing at an FDA approved commercial manufacturing site is described. In this direct compaction process the blends produced were monitored with a Near Infrared (NIR) spectroscopic calibration model developed with partial least squares (PLS) regression. The authors understand that this is the first study where the continuous manufacturing (CM) equipment was used as a gravimetric reference method for the calibration model. A principal component analysis (PCA) model was also developed to identify the powder blend, and determine whether it was similar to the calibration blends. An air diagnostic test was developed to assure that powder was present within the interface when the NIR spectra were obtained. The air diagnostic test as well the PCA and PLS calibration model were integrated into an industrial software platform that collects the real time NIR spectra and applies the calibration models. The PCA test successfully detected an equipment malfunction. Variographic analysis was also performed to estimate the sampling analytical errors that affect the results from the NIR spectroscopic method during commercial production. The system was used to monitor and control a 28 h continuous manufacturing run, where the average drug concentration determined by the NIR method was 101.17% of label claim with a standard deviation of 2.17%, based on 12,633 spectra collected. The average drug concentration for the tablets produced from these blends was 100.86% of label claim with a standard deviation of 0.4%, for 500 tablets analyzed by Fourier Transform Near Infrared (FT-NIR) transmission spectroscopy. The excellent agreement between the mean drug concentration values in the blends and tablets produced provides further evidence of the suitability of the validation strategy that was followed. Copyright © 2018 Elsevier B.V. All rights reserved.

  19. Identification of host fruit volatiles from three mayhaw species (Crataegus series Aestivales) attractive to mayhaw-origin Rhagoletis pomonella flies in the southern United States.

    PubMed

    Cha, Dong H; Powell, Thomas H Q; Feder, Jeffrey L; Linn, Charles E

    2011-09-01

    The apple maggot fly, Rhagoletis pomonella, infests several hawthorn species in the southern USA. Here, we tested the hypothesis that these populations could serve as reservoirs for fruit odor discrimination behaviors facilitating sympatric host race formation and speciation, specifically the recent shift from downy hawthorn (Crataegus mollis) to domestic apple (Malus domestica) in the northern USA. Coupled gas chromatography and electroantennographic detection (GC-EAD), gas chromatography with mass spectrometry (GC-MS), and flight tunnel bioassays were used to identify the behaviorally active natal fruit volatile blends for three of the five major southern hawthorns: C. opaca (western mayhaw), C. aestivalis (eastern mayhaw), and C. rufula (a possible hybrid between C. opaca and C. aestivalis). A 6-component blend was developed for C. opaca (3-methylbutan-1-ol [44%], pentyl acetate [6%], butyl butanoate [6%], propyl hexanoate [6%], butyl hexanoate [26%], and hexyl butanoate [12%]); an 8-component blend for C. aestivalis (3-methylbutan-1-ol [2%], butyl acetate [47%], pentyl acetate [2%], butyl butanoate [12%], propyl hexanoate [1%], butyl hexanoate [25%], hexyl butanoate [9%], and pentyl hexanoate [2%]); and a 9-component blend for C. rufula (3-methylbutan-1-ol [1%], butyl acetate [57%], 3-methylbutyl acetate [3%], butyl butanoate [5%], propyl hexanoate [1%], hexyl propionate [1%], butyl hexanoate [23%], hexyl butanoate [6%], and pentyl hexanoate [3%]). Crataegus aestivalis and C. opaca-origin flies showed significantly higher levels of upwind directed flight to their natal blend in flight tunnel assays compared to the non-natal blend and previously developed apple, northern downy hawthorn, and flowering dogwood blends. Eastern and western mayhaw flies also were tested to the C. rufula blend, with eastern flies displaying higher levels of upwind flight compared with the western flies, likely due to the presence of butyl acetate in the C. aestivalis and C. rufula blends, an agonist compound for eastern mayhaw-origin flies, but a behavioral antagonist for western flies. The results discount the possibility that the apple fly was "pre-assembled" and originated via a recent introduction of southern mayhaw flies predisposed to accepting apple. Instead, the findings are consistent with the possibility of southern mayhaw-infesting fly host races. However, mayhaw fruits do emit several volatiles found in apple. It is, therefore, possible that the ability of the fly to evolve a preference for apple volatiles, although not the entire blend, stemmed, in part, from standing variation related to the presence of these compounds in southern mayhaw fruit.

  20. Multidirectional wear and impact-to-wear tests of phospholipid-polymer-grafted and vitamin E-blended crosslinked polyethylene: a pilot study.

    PubMed

    Kyomoto, Masayuki; Moro, Toru; Takatori, Yoshio; Tanaka, Sakae; Ishihara, Kazuhiko

    2015-03-01

    Modifying the surface and substrate of a crosslinked polyethylene (CLPE) liner may be beneficial for high wear resistance as well as high oxidative stability and excellent mechanical properties, which would be useful in contributing to the long-term performance of orthopaedic bearings. A grafted poly(2-methacryloyloxyethyl phosphorylcholine) (PMPC) layer on a vitamin E-blended crosslinked PE (HD-CLPE[VE]) surface may provide hydrophilicity and lubricity without compromising the oxidative stability or mechanical properties. (1) Will the modifications (PMPC grafting and vitamin E blending) affect the lubrication characteristics of the CLPE surface? (2) Will the modifications affect wear resistance? (3) Will the modifications affect fatigue resistance? We investigated the effects of surface and substrate modifications (PMPC grafting and vitamin E blending) on the wear and fatigue fracture of thin CLPE samples. For each of the untreated and PMPC-grafted CLPE surfaces with and without vitamin E blended (four groups), wettability and lubricity surface analyses were conducted as well as multidirectional wear and impact-to-wear tests using a pin-on-disk testing machine. The water wettability and lubricity (CLPE [mean ± 95% confidence interval]: 23.2° ± 1.8°, 0.005 ± 0.001; HD-CLPE[VE]: 26.0° ± 2.3°, 0.009 ± 0.003) of the PMPC-grafted surfaces were greater (p < 0.001) than that (CLPE: 90.3° ± 1.2°, 0.067 ± 0.015; HD-CLPE[VE]: 90.8° ± 2.0°, 0.063 ± 0.008) of the untreated surface regardless of vitamin E additives. It was observed that the PMPC grafting (CLPE: 0.23 ± 0.06 mg; HD-CLPE[VE]: 0.05 ± 0.10 mg) was associated with reduced gravimetric wear (CLPE: 0.53 ± 0.08 mg, p = 0.004 HD-CLPE[VE]: 0.23 ± 0.07 mg, p = 0.038) in the multidirectional wear test. The PMPC-grafted surface characteristics did not appear to affect the impact fatigue resistance regardless of vitamin E blending. PMPC grafting improved the surface hydrophilicity and lubricity, and it reduced the gravimetric wear in terms of multidirectional sliding. It did not result in differences in terms of the impact-to-unidirectional sliding regardless of vitamin E blending. Further research is needed to evaluate the wear resistance of PMPC-grafted HD-CLPE(VE) in long-term hip simulator tests under normal and severe conditions, which may offer useful clues to the possible performance of these materials in vivo. Our preliminary in vitro findings suggest that some improvement in the wear performance of crosslinked polyethylene acetabular liners in total hip arthroplasty could be obtained using PMPC grafting. Further research is needed to evaluate the wear resistance of PMPC-grafted HD-CLPE(VE) in long-term hip simulator tests under normal and severe conditions, which may offer useful clues to the possible performance of these materials in vivo.

  1. CONCEPTUAL DESIGN ASSESSMENT FOR THE COFIRING OF BIOREFINERY SUPPLIED LIGNIN PROJECT

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    David J. Webster; Jeffrey T. Ranney; Jacqueline G. Broder

    2002-07-01

    The major aspects of this project are proceeding toward completion. Prior to this quarter, design criteria, tentative site selection, facility layout, and preliminary facility cost estimates were completed. Processing of biosolids and pilot facility hydrolysis production have been completed to produce lignin for cofire testing. EERC had received all the biomass and baseline coal fuels for use in testing. All the combustion and fuel handling tests at EERC have been completed. During fuel preparation EERC reported no difficulties in fuel blending and handling. Preliminary cofire test results indicate that the blending of lignin and biosolids with the Colbert coal blendmore » generally reduces NOx emissions, increases the reactivity of the coal, and increases the ash deposition rate on superheater surfaces. Deposits produced from the fuel blends, however, are more friable and hence easier to remove from tube surfaces relative to those produced from the baseline Colbert coal blend. A draft of the final cofire technical report entitled ''Effects of Cofiring Lignin and Biosolids with Coal on Fireside Performance and Combustion Products'' has been prepared and is currently being reviewed by project team members. A final report is expected by mid-third quarter 2002. The TVA-Colbert facility has neared completion of the task to evaluate co-location of the Masada facility on the operation of the power generation facility. The TVA-Colbert fossil plant is fully capable of providing a reliable steam supply. The environmental review, preferred steam supply connection points and steam pipeline routing, and assessment of steam export impacts have been completed without major issue. A cost estimate for the steam supply system was also completed. TVA is further evaluating the impacts of adding lignin to the coal fuel blend and how the steam cost is impacted by proximity of the Masada biomass facility. TVA has provided a draft final report that is under review by team members.« less

  2. Engineering Polymer Blends for Impact Damage Mitigation

    NASA Technical Reports Server (NTRS)

    Gordon, Keith L.; Smith, Russell W.; Working, Dennis C.; Siochi, Emilie J.

    2016-01-01

    Structures containing polymers such as DuPont's Surlyn® 8940, demonstrate puncture healing when impacted by a 9 millimeter projectile traveling from speeds near 300 meters per second (1,100 feet per second) to hypervelocity impacts in the micrometeoroid velocity range of 5 kilometers per second (16,000 feet per second). Surlyn® 8940 puncture heals over a temperature range of minus 30 degrees Centigrade to plus 70 degrees Centigrade and shows potential for use in pressurized vessels subject to impact damage. However, such polymers are difficult to process and limited in applicability due to their low thermal stability, poor chemical resistance and overall poor mechanical properties. In this work, several puncture healing engineered melt formulations were developed. Moldings of melt blend formulations were impacted with a 5.56 millimeter projectile with a nominal velocity of 945 meters per second (3,100 feet per second) at about 25 degrees Centigrade, 50 degrees Centigrade and 100 degrees Centigrade, depending upon the specific blend being investigated. Self-healing tendencies were determined using surface vacuum pressure tests and tensile tests after penetration using tensile dog-bone specimens (ASTM D 638-10). For the characterization of tensile properties both pristine and impacted specimens were tested to obtain tensile modulus, yield stress and tensile strength, where possible. Experimental results demonstrate a range of new puncture healing blends which mitigate damage in the ballistic velocity regime.

  3. Development of an antimicrobial blended white LED system containing pulsed 405nm LEDs for decontamination applications

    NASA Astrophysics Data System (ADS)

    Gillespie, Jonathan B.; Maclean, Michelle; Wilson, Mark P.; Given, Martin J.; MacGregor, Scott J.

    2017-03-01

    This study details the design, build and testing of a prototype antimicrobial blended white light unit containing pulsed red, yellow, green and 405nm LEDs. With a push for alternative methods of disinfection, optical methods have become a topic of interest. Ultra-violet (UV) light is widely known for its antimicrobial properties however; 405nm light has demonstrated significant antimicrobial properties against many common hospital acquired pathogens. In this study, a pulsed, blended, white-light prototype with a high content of 405 nm antimicrobial light, was designed, built and tested. Antimicrobial efficacy testing of the prototype was conducted using Staphylococcus aureus and Pseudomonas. aeruginosa, two bacteria which are common causes of hospital acquired infections. These were exposure to 3 different light outputs from the prototype and the surviving bacteria enumerated. Results showed that the mixed light output provided a much better CRI and light output under which to work. Also, the light output containing 405 nm light provided an antimicrobial effect, with decontamination of 103 CFUml-1 populations of both bacterial species. The other light content (red, yellow, green) had no beneficial or adverse effects on the antimicrobial properties of the 405nm light. The results suggest that with further development, it could be possible to produce an antimicrobial blended white light containing pulsed 405nm light that could supplement or even replace standard white lighting in certain environments.

  4. Toughening modification of poly(butylene terephthalate)/poly(ethylene terephthalate) blends by an epoxy-functionalized elastomer

    NASA Astrophysics Data System (ADS)

    Zhang, Weizhou; Wang, Kai; Yan, Wei; Guo, Weihong

    2017-10-01

    New toughened poly(butylene terephthalate) (PBT)/poly(ethylene terephthalate) (PET) (40/60 wt%) blends were obtained by melting with Glycidyl methacrylate grafted poly(ethylene octane) copolymer (POE-g-GMA), varying the POE-g-GMA content up to 20 wt%, in a twin-screw extruder, followed by injection molding. The influence of POE-g-GMA on the properties of the PBT/PET blends was investigated by mechanical testing, Fourier transform infrared (FT-IR) analysis, gel fractions analysis, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC) and scanning electronic microscopy (SEM). The mechanical testing results indicated that the incorporation of POE-g-GMA led to increases in the notched impact strength and decreases in the tensile strength, flexural strength, and flexural modulus. When POE-g-GMA content reached 20 wt%, the notched impact strength (8.0 kJ m-2) was achieved for the PBT/PET/POE-g-GMA blends. FT-IR results proved that some PBT/PET/POE-g-GMA copolymers were produced, which improved the compatibility between POE-g-GMA and the PBT/PET matrix. The extent of crosslinking was observed by gel fraction measurements. DMA results further testified chain-extending and micro-crosslink reactions occurred between POE-g-GMA and PBT/PET blends. In addition, the reactions induced by POE-g-GMA affected the crystallization behavior of PBT/PET blends obviously, as observed from DSC results. By means of SEM observation of the impact fracture surface morphology, and the discussion of the micro-crosslink reaction process between the epoxide-containing elastomers and PBT/PET matrix, the toughening mechanism was proposed to be taken into account the shear yielding of PBT/PET matrix and cavitation of elastomer particles.

  5. Blend membrane of succinic acid-crosslinked chitosan grafted with heparin/PVA-PEG (polyvinyl alcohol-polyethylene glycol) and its characterization

    NASA Astrophysics Data System (ADS)

    Sangkota, V. D. A.; Lusiana, R. A.; Astuti, Y.

    2018-04-01

    Crosslinking and grafting reactions are required to modify the functional groups on chitosan to increase the number of its active groups. In this study, crosslinking reaction of succinic acid and grafting reaction of heparin on chitosan were conducted to produce a membrane as a candidate of a hemodialysis membrane. The mole ratio between chitosan and succinate acids was varied to obtain the best composition of modified materials. By blending all the material composition with PVA-PEG, the blend was transformed into a membrane. The resulted membrane was then characterized by various test methods such as tests of thickness, weight, water uptake, pH resistance, tensile strength and membrane hydrophilicity. The results showed that the best composition of the membrane reached in the addition of 0.011 gram of succinic acid proved by its highest mechanical strength compared to the other membranes.

  6. Effect of Fuel Composition on Particulate Matter Emissions from a Gasoline Direct Injection Engine

    NASA Astrophysics Data System (ADS)

    Smallwood, Bryden Alexander

    The effects of fuel composition on reducing PM emissions were investigated using a Ford Focus wall-guided gasoline direct injection engine (GDI). Initial results with a 65% isooctane and 35% toluene blend showed significant reductions in PM emissions. Further experiments determined that this decrease was due to a lack of light-end components in that fuel blend. Tests with pentane content lower than 15% were found to have PN concentrations 96% lower than tests with 20% pentane content. This indicates that there is a shift in mode of soot production. Pentane significantly increases the vapour pressure of the fuel blend, potentially resulting in surface boiling, less homogeneous mixtures, or decreased fuel rebound from the piston. PM mass measurements and PN Index values both showed strong correlations with the PN concentration emissions. In the gaseous exhaust, THC, pentane, and 1,3 butadiene showed strong correlations with the PM emissions.

  7. [Study on the calcium-based sorbent for removal fluorine during coal combustion].

    PubMed

    Li, Shu-ling; Qi, Qing-jie; Liu, Jian-zhong; Cao, Xin-yu; Zhou, Jun-hu; Cen, Ke-fa

    2004-03-01

    In the paper, the reaction of CaO-HF and fluorine removal mechanics at high temperature by blending calcium-based sorbents with coal during coal combustion were discussed, and test results about fluorine retention during coal combustion in fluidized bed and chain-grate furnace were reported. The results identified that lime and calcium-based sorbets developed can restratin the emission of fluorine during coal combustion. The efficiency of fluorine removal can reach 66.7%-70.0% at Ca/F 60-70 by blending lime with coal in fluidized bed combustion, and the efficiency of fluorine removal are between 57.32% and 75.19% by blending calcium-based sorbets with coal in chain-grate furnace combustion. Blending CaO or lime with coal during coal combustion can remove SO2 and HF simultaneously.

  8. Thermodynamic aspects of reformulation of automotive fuels

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zudkevitch, D.; Murthy, A.K.S.; Gmehling, J.

    1995-09-01

    A study of procedures for measuring and predicting the RVP and the initial vapor emissions of reformulated gasoline blends which contain one or more oxygenated compounds, viz., Ethanol, MTBE, ETBE, and TAME is discussed. Two computer simulation methods were programmed and tested. In one method, Method A, the D-86 distillation data on the blend are used for predicting the blend`s RVP from a simulation of the Mini RVPE (RVP Equivalent) experiment. The other method, Method B, relies on analytical information (PIANO analyzes) on the nature of the base gasoline and utilizes classical thermodynamics for simulating the same RVPE, Mini experiment.more » Method B, also, predicts the composition and other properties of the initial vapor emission from the fuel. The results indicate that predictions made with both methods agree very well with experimental values. The predictions with Method B illustrate that the admixture of an oxygenate to a gasoline blend changes the volatility of the blend and, also, the composition of the vapor emission. From the example simulations, a blend with 10 vol % ethanol increases the RVP by about 0.8 psi. The accompanying vapor emission will contain about 15% ethanol. Similarly, the vapor emission of a fuel blend with 11 vol % MTBE was calculated to contain about 11 vol % MTBE. Predictions of the behavior of blends with ETBE and ETBE+Ethanol are also presented and discussed. Recognizing that quite some efforts have been invested in developing empirical correlations for predicting RVP, the writers consider the purpose of this paper to be pointing out that the methods of classical thermodynamics are adequate and that there is a need for additional work in developing certain fundamental data that are still lacking.« less

  9. Development of a mosquito attractant blend of small molecules against host-seeking Aedes aegypti.

    PubMed

    Saratha, R; Mathew, Nisha

    2016-04-01

    A mosquito's dependence on olfaction in the hunt for human host could be efficiently exploited to protect humans from mosquito bites. The present study is undertaken to make the most attractant compound blend for Aedes aegypti mosquitoes to lure them to traps. Eleven molecules (M1-M11) at different dilutions were screened for attractancy against non-blood-fed adult female mosquitoes in an olfactometer. The results showed that the attractancy was dependent on both the chemical nature of the molecule and the strength of the odor. Out of 11 molecules screened, 9 showed significant attractancy (P < 0.05) when tested individually. The attractancy was in the order of M11 > M7 > M6 > M10 > M9 > M3 > M2 > M1 > M4 with attractancy indices (AIs) 86.11, 55.93, 55.17, 54, 52.94, 52, 50, 43.64, and 32, respectively, at the optimum dilutions. Seven blends (I-VII) were made and were screened for attractancy against Ae. aegypti. All the blends showed significant attractancy (P < 0.05). The attractancy was in the order of blend VII > III > IV > I > VI > V > II with AIs 96.63, 89.19, 65, 57.89, 56.1, 47.13, and 44.44, respectively. Among the seven blends, blend VII with constituent molecules M6, M9, M10, and M11 is the most promising with an AI value of 96.63. This blend will be useful in luring the host-seeking mosquitoes to traps. The field efficacy of these attractant blends may be explored in the future.

  10. Children in Blended and Step Families. Foundation for Child and Youth Studies Selected Papers Number 44.

    ERIC Educational Resources Information Center

    Phillips, Shelley

    Fairy tales dramatize a widely held presumption that children are at high risk of abuse in stepfamilies. The idea seems almost accepted as fact, yet it has never been adequately tested. This paper provides detailed information about life in blended and stepfamilies. Sections focus on (1) stepmothers; (2) children's views of their stepmothers; (3)…

  11. 40 CFR 1065.701 - General requirements for test fuels.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... procedure 1 Light distillate and light blends with residual ASTM D975-07b. Diesel Middle distillate ASTM D6985-04a. Biodiesel (B100) ASTM D6751-07b. Intermediate and residual fuel All See § 1065.705. Gasoline Motor vehicle gasoline ASTM D4814-07a. Minor oxygenated gasoline blends ASTM D4814-07a. Alcohol Ethanol...

  12. Carbonaceous PM2.5 emitted from light-duty vehicles operating on low-level ethanol fuel blends.

    EPA Science Inventory

    This study aims to examine carbonaceous aerosol emissions from three Tier 2-certified 2008 model year LDVs burning e0, e10, and e85 fuel blends at -7°C and 24°C. The LDVs were tested on an electric chasis dynamometer using the LA-92 Urban Driving Cycle (UDC). Exhaust was ...

  13. Adopting a Blended Learning Approach: Challenges Encountered and Lessons Learned in an Action Research Study

    ERIC Educational Resources Information Center

    Kenney, Jane; Newcombe, Ellen

    2011-01-01

    Adopting a new teaching approach is often a daunting task especially if one is an early adopter in a limited-resource environment. This article describes the challenges encountered and the strategies used in pilot testing a blended instructional method in a large size class within the college of education at a medium-sized university. The main…

  14. Reducing power production costs by utilizing petroleum coke. Annual report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Galbreath, K.C.

    1998-07-01

    A Powder River Basin subbituminous coal from the North Antelope mine and a petroleum shot coke were received from Northern States Power Company (NSP) for testing the effects of parent fuel properties on coal-coke blend grindability and evaluating the utility of petroleum coke blending as a strategy for improving electrostatic precipitator (ESP) particulate collection efficiency. Petroleum cokes are generally harder than coals, as indicated by Hardgrove grindability tests. Therefore, the weaker coal component may concentrate in the finer size fractions during the pulverizing of coal-coke blends. The possibility of a coal-coke size fractionation effect is being investigated because it maymore » adversely affect combustion performance, it may enhance ESP particulate collection efficiency. Petroleum cokes contain much higher concentrations of V relative to coals. Consequently, coke blending can significantly increase the V content of fly ash resulting from coal-coke combustion. Pentavalent vanadium oxide (V{sub 2}O{sub 5}) is a known catalyst for transforming gaseous sulfur dioxide (SO{sub 2}[g]) to gaseous sulfur trioxide (SO{sub 3}[g]). The presence of SO{sub 3}(g) strongly affects fly ash resistivity and, thus, ESP performance.« less

  15. A high-throughput media design approach for high performance mammalian fed-batch cultures

    PubMed Central

    Rouiller, Yolande; Périlleux, Arnaud; Collet, Natacha; Jordan, Martin; Stettler, Matthieu; Broly, Hervé

    2013-01-01

    An innovative high-throughput medium development method based on media blending was successfully used to improve the performance of a Chinese hamster ovary fed-batch medium in shaking 96-deepwell plates. Starting from a proprietary chemically-defined medium, 16 formulations testing 43 of 47 components at 3 different levels were designed. Media blending was performed following a custom-made mixture design of experiments considering binary blends, resulting in 376 different blends that were tested during both cell expansion and fed-batch production phases in one single experiment. Three approaches were chosen to provide the best output of the large amount of data obtained. A simple ranking of conditions was first used as a quick approach to select new formulations with promising features. Then, prediction of the best mixes was done to maximize both growth and titer using the Design Expert software. Finally, a multivariate analysis enabled identification of individual potential critical components for further optimization. Applying this high-throughput method on a fed-batch, rather than on a simple batch, process opens new perspectives for medium and feed development that enables identification of an optimized process in a short time frame. PMID:23563583

  16. Using a mass balance to determine the potency loss during the production of a pharmaceutical blend.

    PubMed

    Mackaplow, Michael B

    2010-09-01

    The manufacture of a blend containing the active pharmaceutical ingredient (API) and inert excipients is a precursor for the production of most pharmaceutical capsules and tablets. However, if there is a net water gain or preferential loss of API during production, the potency of the final drug product may be less than the target value. We use a mass balance to predict the mean potency loss during the production of a blend via wet granulation and fluidized bed drying. The result is an explicit analytical equation for the change in blend potency a function of net water gain, solids losses (both regular and high-potency), and the fraction of excipients added extragranularly. This model predicts that each 1% gain in moisture content (as determined by a loss on drying test) will decrease the API concentration of the final blend at least 1% LC. The effect of pre-blend solid losses increases with their degree of superpotency. This work supports Quality by Design by providing a rational method to set the process design space to minimize blend potency losses. When an overage is necessary, the model can help justify it by providing a quantitative, first-principles understanding of the sources of potency loss. The analysis is applicable to other manufacturing processes where the primary sources of potency loss are net water gain and/or mass losses.

  17. Physicochemical and FTIR Study of Diesel-Hydrogen Peroxide Fuel Blend

    NASA Astrophysics Data System (ADS)

    Saad Khan, Muhammad; Ahmed, Iqbal; Lal, Bhajan; Idris, Al-Amin; Albeirutty, Muhammad H.; Ayoub, Muhammad; Sufian, Suriati binti

    2018-04-01

    Physicochemical properties of combustion fuels play a key role in determining the qualitative and quantitative characteristics, reliability and health effects associated with emissions. This paper reports the preparation of polysaccharide (PS) based emulsifier for stable blending of petroleum diesel-hydrogen peroxide (H2O2) and investigated the influence of H2O2 as diesel fuel blends on the physicochemical properties and characteristics. The quantity of PS-emulsifier was kept at 5 volume % (vol. %) and the volume ratio of H2O2 were varied 5-15 vol. % to reference diesel (RD), respectively. The blended diesel/H2O2 fuel were prepared under inert oxygen (O2) gas closed heating system; afterthought, physiochemical properties of diesel/H2O2 blend were evaluated at standard ASTM D-975 testing method. The kinetic properties show the interaction of RD and H2O2 blend at presence of PS emulsifier which exhibit the phenomenon to diminish the interfacial tension among the two different phases to form a homogenized stable solution. Results revealed that H2O2 is capable of enhancing the diesel fuel properties and showed that the addition of H2O2 in a diesel fuel blend are lied within the ranges of standard ASTM D-975. Due to further oxygen atom present in H2O2, it can facilitate the combustion process which ultimately effect on exhaust emission.

  18. Training community healthcare workers on the use of information and communication technologies: a randomised controlled trial of traditional versus blended learning in Malawi, Africa.

    PubMed

    Mastellos, Nikolaos; Tran, Tammy; Dharmayat, Kanika; Cecil, Elizabeth; Lee, Hsin-Yi; Wong, Cybele C Peng; Mkandawire, Winnie; Ngalande, Emmanuel; Wu, Joseph Tsung-Shu; Hardy, Victoria; Chirambo, Baxter Griphin; O'Donoghue, John Martin

    2018-04-02

    Despite the increasing uptake of information and communication technologies (ICT) within healthcare services across developing countries, community healthcare workers (CHWs) have limited knowledge to fully utilise computerised clinical systems and mobile apps. The 'Introduction to Information and Communication Technology and eHealth' course was developed with the aim to provide CHWs in Malawi, Africa, with basic knowledge and computer skills to use digital solutions in healthcare delivery. The course was delivered using a traditional and a blended learning approach. Two questionnaires were developed and tested for face validity and reliability in a pilot course with 20 CHWs. Those were designed to measure CHWs' knowledge of and attitudes towards the use of ICT, before and after each course, as well as their satisfaction with each learning approach. Following validation, a randomised controlled trial was conducted to assess the effectiveness of the two learning approaches. A total of 40 CHWs were recruited, stratified by position, gender and computer experience, and allocated to the traditional or blended learning group using block randomisation. Participants completed the baseline and follow-up questionnaires before and after each course to assess the impact of each learning approach on their knowledge, attitudes, and satisfaction. Per-item, pre-post and between-group, mean differences for each approach were calculated using paired and unpaired t-tests, respectively. Per-item, between-group, satisfaction scores were compared using unpaired t-tests. Scores across all scales improved after attending the traditional and blended learning courses. Self-rated ICT knowledge was significantly improved in both groups with significant differences between groups in seven domains. However, actual ICT knowledge scores were similar across groups. There were no significant differences between groups in attitudinal gains. Satisfaction with the course was generally high in both groups. However, participants in the blended learning group found it more difficult to follow the content of the course. This study shows that there is no difference between blended and traditional learning in the acquisition of actual ICT knowledge among community healthcare workers in developing countries. Given the human resource constraints in remote resource-poor areas, the blended learning approach may present an advantageous alternative to traditional learning.

  19. Paleocurrents in the Charlie-Gibbs Fracture Zone during the Late Quaternary

    NASA Astrophysics Data System (ADS)

    Bashirova, L. D.; Dorokhova, E.; Sivkov, V.; Andersen, N.; Kuleshova, L. A.; Matul, A.

    2017-12-01

    The sedimentary processes prevailing in the Charlie-Gibbs Fracture Zone (CGFZ) are gravity flows. They rework pelagic sediments and contourites, and hereby mask the paleoceanographic information partly. The aim of this work is to study sediments of the AMK-4515 core taken in eastern part of the CGFZ. The sediment core AMK-4515 (52°03.14" N, 29°00.12" W; 370 cm length, water depth 3590 m) is located in the southern valley of the CGFZ. This natural deep corridor is influenced by both the westward Iceland-Scotland Overflow Water and underlying counterflow from the Newfoundland Basin. An alternation of the calcareous silty clays and hemipelagic clayey muds in the studied section indicates similarity between our core and long cores taking from CGFZ. A sharp facies shift was found at 80 cm depth in the investigated core. Only the upper section (0-80 cm) is valid for paleoreconstruction. Planktonic foraminiferal distribution and sea-surface temperature (SST) derived from these allow for tracing the PF and NAC latitudinal migrations during investigated period. So-called sortable silt mean size (SS) was used as proxy for reconstruction of bottom current intensity. The age model is based on δ18O and AMS 14C dating, as well as ice-rafted debris (IRD) counts and CaCO3 content. Stratigraphic subdivision of this section allows to allocate 2 marine isotope stages (MIS) covering the last 27 ka. We refer sediments below this level (80-370 cm) to upper part of turbidite, which was formed as a result of massive slide in the southern channel of the CGFZ. Sandy particles were deposited first, underlying silts and clays. This short-term event occurred so quickly that pelagic sedimentation played no role and was not reflected in the grain size distributions. There is evidence for the significant role of gravity flows in sedimentation in the southern channel of the CGFZ. According to our data, the massive sediment slide occurred in the CGFZ about 27 ka. The authors are grateful to RSF (grant No.14-50-00095) for financial support of analytical studies. Absolute datings were obtained with support from the IKBFU 5-100 Russian academic excellence project.

  20. Design of a prospective study on mental health and quality of life of maltreated children (aged 5–16 years) after a report to an advice and reporting center on child abuse and neglect

    PubMed Central

    2013-01-01

    Background Child maltreatment is recognized as a widespread problem with huge implications for mental health and quality of life. Studies have repeatedly shown that victims of child maltreatment report significantly more adverse life outcomes than non-victims. The main objective of the study is (1) to examine the mental health and quality of life of maltreated children over a 1.5 year period beginning shortly after a report has been filed with an Advies- en Meldpunt Kindermishandeling (AMK) (advice and reporting center on child abuse and neglect). Secondary objectives are: (2) to examine how relevant determinants influence the mental health and quality of life of maltreated children, and (3) to examine differences in mental health and quality of life outcomes when comparing families of Dutch origin with families originating from Morocco and Suriname. Methods/Design A prospective study will be performed, in which parent–child dyads will be followed over a 1.5 year period. Participants will be recruited shortly after the report to the AMK and they will be asked to complete a questionnaire four times, at baseline and every six months thereafter. Data will be analyzed using a longitudinal multi-level analysis. Discussion The study is expected to yield evidence about the mental health and quality of life of maltreated children and about determinants that influence their mental health and quality of life outcomes. Strengths of this study are (1) the design which makes it possible to start examining outcomes shortly after or even during the actual maltreatment and to follow parent–child dyads for 1.5 years, and (2) asking children as informants about their own situation by making use of self-report questionnaires as much as possible. Limitations include the risks of selection bias and loss to follow-up during 1.5 years of data collection. Trial registration NTR3674, funded by ZonMw, project 15700.2012. PMID:24106987

  1. Low-speed wind-tunnel tests of a one-tenth-scale model of a blended-arrow advanced supersonic transport. [conducted in Langley full-scale tunnel

    NASA Technical Reports Server (NTRS)

    Lemore, H. C.; Parett, L. P.

    1975-01-01

    Tests were conducted in the Langley full scale tunnel to determine the low-speed aerodynamic characteristics of a 1/10 scale model of a blended-arrow advanced supersonic transport. Tests were made for the clean configuration and a high-lift configuration with several combinations of leading- and trailing-edge flaps deflected for providing improved lift and longitudinal stability in the landing and takeoff modes. The tests were conducted for a range of angles of attack from about -6 deg to 30 deg, sideslip angles from -5 deg to 10 deg, and for Reynolds numbers from 6.78 x 1,000,000 to 13.85 x 1,000,000 corresponding to test velocities of 41 knots to 85 knots, respectively.

  2. Overview of Low-Speed Aerodynamic Tests on a 5.75% Scale Blended-Wing-Body Twin Jet Configuration

    NASA Technical Reports Server (NTRS)

    Vicroy, Dan D.; Dickey, Eric; Princen, Norman; Beyar, Michael D.

    2016-01-01

    The NASA Environmentally Responsible Aviation (ERA) Project sponsored a series of computational and experimental investigations of the propulsion and airframe integration issues associated with Hybrid-Wing-Body (HWB) or Blended-Wing-Body (BWB) configurations. NASA collaborated with Boeing Research and Technology (BR&T) to conduct this research on a new twin-engine Boeing BWB transport configuration. The experimental investigations involved a series of wind tunnel tests with a 5.75-percent scale model conducted in two low-speed wind tunnels. This testing focused on the basic aerodynamics of the configuration and selection of the leading edge Krueger slat position for takeoff and landing. This paper reviews the results and analysis of these low-speed wind tunnel tests.

  3. Catalytic combustion with incompletely vaporized residual fuel

    NASA Technical Reports Server (NTRS)

    Rosfjord, T. J.

    1981-01-01

    Catalytic combustion of fuel lean mixtures of incompletely vaporized residual fuel and air was investigated. The 7.6 cm diameter, graded cell reactor was constructed from zirconia spinel substrate and catalyzed with a noble metal catalyst. Streams of luminous particles exited the rector as a result of fuel deposition and carbonization on the substrate. Similar results were obtained with blends of No. 6 and No. 2 oil. Blends of shale residual oil and No. 2 oil resulted in stable operation. In shale oil blends the combustor performance degraded with a reduced degree of fuel vaporization. In tests performed with No. 2 oil a similar effect was observed.

  4. Blending problem-based learning with Web technology positively impacts student learning outcomes in acid-base physiology.

    PubMed

    Taradi, Suncana Kukolja; Taradi, Milan; Radic, Kresimir; Pokrajac, Niksa

    2005-03-01

    World Wide Web (Web)-based learning (WBL), problem-based learning (PBL), and collaborative learning are at present the most powerful educational options in higher education. A blended (hybrid) course combines traditional face-to-face and WBL approaches in an educational environment that is nonspecific as to time and place. To provide educational services for an undergraduate second-year elective course in acid-base physiology, a rich, student-centered educational Web-environment designed to support PBL was created by using Web Course Tools courseware. The course is designed to require students to work in small collaborative groups using problem solving activities to develop topic understanding. The aim of the study was to identify the impact of the blended WBL-PBL-collaborative learning environment on student learning outcomes. Student test scores and satisfaction survey results from a blended WBL-PBL-based test group (n = 37) were compared with a control group whose instructional opportunities were from a traditional in-class PBL model (n = 84). WBL students scored significantly (t = 3.3952; P = 0.0009) better on the final acid-base physiology examination and expressed a positive attitude to the new learning environment in the satisfaction survey. Expressed in terms of a difference effect, the mean of the treated group (WBL) is at the 76th percentile of the untreated (face-to-face) group, which stands for a "medium" effect size. Thus student progress in the blended WBL-PBL collaborative environment was positively affected by the use of technology.

  5. Effects of a saw palmetto herbal blend in men with symptomatic benign prostatic hyperplasia.

    PubMed

    Marks, L S; Partin, A W; Epstein, J I; Tyler, V E; Simon, I; Macairan, M L; Chan, T L; Dorey, F J; Garris, J B; Veltri, R W; Santos, P B; Stonebrook, K A; deKernion, J B

    2000-05-01

    We tested the effects of a saw palmetto herbal blend in men with symptomatic benign prostatic hyperplasia (BPH) via a randomized, placebo controlled trial. We randomized 44 men 45 to 80 years old with symptomatic BPH into a trial of a saw palmetto herbal blend versus placebo. End points included routine clinical measures (symptom score, uroflowmetry and post-void residual urine volume), blood chemistry studies (prostate specific antigen, sex hormones and multiphasic analysis), prostate volumetrics by magnetic resonance imaging, and prostate biopsy for zonal tissue morphometry and semiquantitative histology studies. Saw palmetto herbal blend and placebo groups had improved clinical parameters with a slight advantage in the saw palmetto group (not statistically significant). Neither prostate specific antigen nor prostate volume changed from baseline. Prostate epithelial contraction was noted, especially in the transition zone, where percent epithelium decreased from 17.8% at baseline to 10.7% after 6 months of saw palmetto herbal blend (p <0.01). Histological studies showed that the percent of atrophic glands increased from 25. 2% to 40.9% after treatment with saw palmetto herbal blend (p <0.01). The mechanism of action appeared to be nonhormonal but it was not identified by tissue studies of apoptosis, cellular proliferation, angiogenesis, growth factors or androgen receptor expression. We noted no adverse effects of saw palmetto herbal blend. When the study was no longer blinded, 41 men elected to continue therapy in an open label extension. Saw palmetto herbal blend appears to be a safe, highly desirable option for men with moderately symptomatic BPH. The secondary outcome measures of clinical effect in our study were only slightly better for saw palmetto herbal blend than placebo (not statistically significant). However, saw palmetto herbal blend therapy was associated with epithelial contraction, especially in the transition zone (p <0.01), indicating a possible mechanism of action underlying the clinical significance detected in other studies.

  6. Physical-biopolymer characterization of polyhydroxybutyrate-co-hydroxyvalerate (PHBV) blended with natural rubber latex

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kuntanoo, K., E-mail: thip-kk@hotmail.com; Promkotra, S., E-mail: sarunya@kku.ac.th; Kaewkannetra, P., E-mail: paknar@kku.ac.th

    A biopolymer of polyhydroxybutyrate-co-hydroxyvalerate (PHBV) is blended with bio-based materials, natural rubber latex, to improve their microstructures. The various ratios between PHBV and natural rubber latex are examined to develop their mechanical properties. In general, physical properties of PHBV are hard, brittle and low flexible while natural rubber (NR) is presented itself as high elastic materials. Concentrations of the PHBV solution are constituted at 1%, 2% and 3% (w/v). The mixtures of their PHBV solutions to natural rubber latex are produced the blended films in three different ratios of 4:6, 5:5 and 6:4, respectively. They are characterized by appearance analysesmore » which are the scanning electron microscope (SEM), universal testing machine (UTM) and differential scanning calorimetry (DSC). The SEM photomicrographs of the blended films and the controlled PHBV can provide the void distribution in the range of 12-14% and 19-21%, respectively. For mechanical properties of the blended films, the various elastic moduli of 1%, 2% and 3% (w/v) PHBV are the average of 773, 956 and 1,007 kPa, respectively. The tensile strengths of the blends increase with the increased concentrations of PHBV, similarly trend to the elastic modulus. The crystallization and melting behavior of unmixed PHBV and the blends are determined by DSC. Melting transition temperatures (T{sub m}) of the unmixed PHBV are stated two melting peak at 154°C and 173°C. Besides, the melting peaks of the blends alter in the range of 152-156°C and 168-171°C, respectively. According to morphology of the blends, the void distribution decreases twice compared to the unmixed PHBV. The results of mechanical properties and thermal analysis indicate that the blended PHBV can be developed their properties by more resilient and wide range of temperature than usual.« less

  7. Using Innovative Tools to Teach Computer Application to Business Students--A Hawthorne Effect or Successful Implementation Here to Stay

    ERIC Educational Resources Information Center

    Khan, Zeenath Reza

    2014-01-01

    A year after the primary study that tested the impact of introducing blended learning and guided discovery to help teach computer application to business students, this paper looks into the continued success of using guided discovery and blended learning with learning management system in and out of classrooms to enhance student learning.…

  8. Influence of electron beam irradiation on mechanical and thermal properties of polypropylene/polyamide blend

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Nakamura, Shigeya, E-mail: shi-nakamura@hitachi-chem.co.jp; Tokumitsu, Katsuhisa

    The effects of electron beam irradiation on the mechanical and thermal properties of polypropylene (PP) and polyamide6 (PA6) blends-with talc 20 wt% as filler, SEBS-g-MAH as compatibilizer, and triallyl isocyanurate as crosslinking agent-were investigated. Although the tensile and flexural moduli and strengths of the PP/PA6 blends with talc, SEBS-g-MAH, and TAIC could be increased by the application of electron beam irradiation, the impact strength was decreased. Ddifferential scanning calorimetryer measurements showed that the melting temperatures of all PP/PA6 blends were decreased with increases in the electron beam irradiationdose. From dynamic mechanical analyzer results, a storage modulus curve in the plateaumore » region was observed only in the PP/PA6 blends with talc, SEBS-g-MAH, and TAIC; the storage modulus increased with increasing electron beam irradiation dose, indicating that the three-dimensional network developed gradually in the more amorphous PA6. As a result, the most significant improvement observed in heat distortion tests under high load (1.8 MPa) occurred at 200 kGy.« less

  9. Blended particle filters for large-dimensional chaotic dynamical systems

    PubMed Central

    Majda, Andrew J.; Qi, Di; Sapsis, Themistoklis P.

    2014-01-01

    A major challenge in contemporary data science is the development of statistically accurate particle filters to capture non-Gaussian features in large-dimensional chaotic dynamical systems. Blended particle filters that capture non-Gaussian features in an adaptively evolving low-dimensional subspace through particles interacting with evolving Gaussian statistics on the remaining portion of phase space are introduced here. These blended particle filters are constructed in this paper through a mathematical formalism involving conditional Gaussian mixtures combined with statistically nonlinear forecast models compatible with this structure developed recently with high skill for uncertainty quantification. Stringent test cases for filtering involving the 40-dimensional Lorenz 96 model with a 5-dimensional adaptive subspace for nonlinear blended filtering in various turbulent regimes with at least nine positive Lyapunov exponents are used here. These cases demonstrate the high skill of the blended particle filter algorithms in capturing both highly non-Gaussian dynamical features as well as crucial nonlinear statistics for accurate filtering in extreme filtering regimes with sparse infrequent high-quality observations. The formalism developed here is also useful for multiscale filtering of turbulent systems and a simple application is sketched below. PMID:24825886

  10. Improvement of wear resistance of plasma-sprayed molybdenum blend coatings

    NASA Astrophysics Data System (ADS)

    Ahn, Jeehoon; Hwang, Byoungchul; Lee, Sunghak

    2005-06-01

    The wear resistance of plasma sprayed molybdenum blend coatings applicable to synchronizer rings or piston rings was investigated in this study. Four spray powders, one of which was pure molybdenum and the others blended powders of bronze and aluminum-silicon alloy powders mixed with molybdenum powders, were sprayed on a low-carbon steel substrate by atmospheric plasma spraying. Microstructural analysis of the coatings showed that the phases formed during spraying were relatively homogeneously distributed in the molybdenum matrix. The wear test results revealed that the wear rate of all the coatings increased with increasing wear load and that the blended coatings exhibited better wear resistance than the pure molybdenum coating, although the hardness was lower. In the pure molybdenum coatings, splats were readily fractured, or cracks were initiated between splats under high wear loads, thereby leading to the decrease in wear resistance. On the other hand, the molybdenum coating blended with bronze and aluminum-silicon alloy powders exhibited excellent wear resistance because hard phases such as CuAl2 and Cu9Al4 formed inside the coating.

  11. Carbon nano fibers reinforced composites origami inspired mechanical metamaterials with passive and active properties

    NASA Astrophysics Data System (ADS)

    Kshad, Mohamed Ali E.; D'Hondt, Clement; Naguib, Hani E.

    2017-10-01

    Core panels used for compression or impact damping are designed to dissipate energy and to reduce the transferred force and energy. They are designed to have high strain and deformation with low density. The geometrical configuration of such cores plays a significant role in redistributing the applied forces to dampen the compression and impact energy. Origami structures are renowned for affording large macroscopic deformation which can be employed for force redistribution and energy damping. The material selection for the fabrication of origami structures affects the core capacity to withstand compression and impact loads. Polymers are characterized by their high compression and impact resistance; the drawback of polymers is the low stiffness and elastic moduli compared with metallic materials. This work is focused on the study of the effect of Carbon Nano Fibers (CNF) on the global mechanical properties of the origami panel cores made of polymeric blends. The base matrix materials used were Polylactic Acid (PLA) and Thermoplastic Polyurethane (TPU) blends, and the percentages of the PLA/TPU were 100/0, 20/80, 65/35, 50/50, 20/80, and 0/100 as a percentage of weight. The weight percentages of CNF added to the polymeric blends were 1%, 3%, and 5%. This paper deals with the fabrication process of the polymeric reinforced blends and the origami cores, in order to predict the best fabrication conditions. The dynamic scanning calorimetry and the dynamic mechanical analyzer were used to test the reinforced blended base material for thermomechanical and viscoelastic properties. The origami core samples were fabricated using per-molded geometrical features and then tested for compression and impact properties. The results of the study were compared with previous published results which showed that there is considerable enhancement in the mechanical properties of the origami cores compared with the pure blended polymeric origami cores. The active properties of the origami unit cell made of composite polymers containing a low percentage of CNF were also investigated in this study, in which the shape memory effect test conducted on the origami unit cell.

  12. Thermal and mechanical behavior of flame retardant epoxy-polyesterurethane blends

    NASA Astrophysics Data System (ADS)

    Patel, R. H.; Hirani, A. V.; Kachhia, P. H.

    2016-05-01

    Polyesterurethanes are used in different applications due to their unique combination of the properties like toughness, flexibility, solvent resistance, etc. Nowadays flame retardant properties of polymers are of commercial interest because of their potential use in high performance applications. In the present study attempts have been taken to improve the flame retardant properties of conventional epoxy resin by incorporating phosphorus based polyesterurethane. Polyesterurethane has been synthesized in the laboratory and characterized by chemical and instrumental analysis techniques. Thermal stability and char value of the blends have been determined using thermogravimetric analysis technique. Limiting Oxygen Index (LOI) and UL-94 test methods have been used to determine the flame retardant properties of neat polymer and their blends in film form. Mechanical properties like tensile strength, elongation and impact resistance of the blends have been found out. Polyblend of epoxy resin with phosphorus based polyesterurethane has improved flame retardant properties compare to neat epoxy resin.

  13. Peel/seal properties of poly(ethylene methyl acrylate)/polybutene-1 blend films

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Mohammdi, Seyedeh Raziyeh; Ajji, Abdellah; Tabatabaei, Seyed H.

    Nowadays, the possibility to easy open a food package is of great interest both from the consumer and food producers’ perspective. In this study, the peel/seal properties of poly (ethylene methyl acrylate) (EMA)/polybutene-1 (PB-1) blend films were investigated. Three blends of EMA/PB-1 with different methyl acrylate (MA) content were prepared using cast extrusion process. Differential Scanning Calorimetry (DSC) was used to investigate the thermal behavior as well as the crystalinity of the blends. The effect of polymer matrix on the crystalline structure of PB-1 was studied using Wide Angle X-ray Diffraction (WAXD) and DSC. T-peel tests were carried out onmore » the heat sealed films at various seal temperatures. The effect of MA content and heat seal temperature on peel/seal properties (i.e. peel initiation temperature, temperature window of sealability and peel strength) of the films were studied.« less

  14. Green Composites Based on Blends of Polypropylene with Liquid Wood Reinforced with Hemp Fibers: Thermomechanical Properties and the Effect of Recycling Cycles.

    PubMed

    Cicala, Gianluca; Tosto, Claudio; Latteri, Alberta; La Rosa, Angela Daniela; Blanco, Ignazio; Elsabbagh, Ahmed; Russo, Pietro; Ziegmann, Gerhard

    2017-08-26

    Green composites from polypropylene and lignin-based natural material were manufactured using a melt extrusion process. The lignin-based material used was the so called "liquid wood". The PP/"Liquid Wood" blends were extruded with "liquid wood" content varying from 20 wt % to 80 wt %. The blends were thoroughly characterized by flexural, impact, and dynamic mechanical testing. The addition of the Liquid Wood resulted in a great improvement in terms of both the flexural modulus and strength but, on the other hand, a reduction of the impact strength was observed. For one blend composition, the composites reinforced with hemp fibers were also studied. The addition of hemp allowed us to further improve the mechanical properties. The composite with 20 wt % of hemp, subjected to up to three recycling cycles, showed good mechanical property retention and thermal stability after recycling.

  15. A Science and Risk-Based Pragmatic Methodology for Blend and Content Uniformity Assessment.

    PubMed

    Sayeed-Desta, Naheed; Pazhayattil, Ajay Babu; Collins, Jordan; Doshi, Chetan

    2018-04-01

    This paper describes a pragmatic approach that can be applied in assessing powder blend and unit dosage uniformity of solid dose products at Process Design, Process Performance Qualification, and Continued/Ongoing Process Verification stages of the Process Validation lifecycle. The statistically based sampling, testing, and assessment plan was developed due to the withdrawal of the FDA draft guidance for industry "Powder Blends and Finished Dosage Units-Stratified In-Process Dosage Unit Sampling and Assessment." This paper compares the proposed Grouped Area Variance Estimate (GAVE) method with an alternate approach outlining the practicality and statistical rationalization using traditional sampling and analytical methods. The approach is designed to fit solid dose processes assuring high statistical confidence in both powder blend uniformity and dosage unit uniformity during all three stages of the lifecycle complying with ASTM standards as recommended by the US FDA.

  16. Organic biowastes blend selection for composting industrial eggshell by-product: experimental and statistical mixture design.

    PubMed

    Soares, Micaela A R; Andrade, Sandra R; Martins, Rui C; Quina, Margarida J; Quinta-Ferreira, Rosa M

    2012-01-01

    Composting is one of the technologies recommended for pre-treating industrial eggshells (ES) before its application in soils, for calcium recycling. However, due to the high inorganic content of ES, a mixture of biodegradable materials is required to assure a successful procedure. In this study, an adequate organic blend composition containing potato peel (PP), grass clippings (GC) and wheat straw (WS) was determined by applying the simplex-centroid mixture design method to achieve a desired moisture content, carbon: nitrogen ratio and free air space for effective composting of ES. A blend of 56% PP, 37% GC and 7% WS was selected and tested in a self heating reactor, where 10% (w/w) of ES was incorporated. After 29 days of reactor operation, a dry matter reduction of 46% was achieved and thermophilic temperatures were maintained during 15 days, indicating that the blend selected by statistical approach was adequate for composting of ES.

  17. Green Composites Based on Blends of Polypropylene with Liquid Wood Reinforced with Hemp Fibers: Thermomechanical Properties and the Effect of Recycling Cycles

    PubMed Central

    Latteri, Alberta; La Rosa, Angela Daniela; Elsabbagh, Ahmed; Ziegmann, Gerhard

    2017-01-01

    Green composites from polypropylene and lignin-based natural material were manufactured using a melt extrusion process. The lignin-based material used was the so called “liquid wood”. The PP/“Liquid Wood” blends were extruded with “liquid wood” content varying from 20 wt % to 80 wt %. The blends were thoroughly characterized by flexural, impact, and dynamic mechanical testing. The addition of the Liquid Wood resulted in a great improvement in terms of both the flexural modulus and strength but, on the other hand, a reduction of the impact strength was observed. For one blend composition, the composites reinforced with hemp fibers were also studied. The addition of hemp allowed us to further improve the mechanical properties. The composite with 20 wt % of hemp, subjected to up to three recycling cycles, showed good mechanical property retention and thermal stability after recycling. PMID:28846607

  18. Morphology Formation in PC/ABS Blends during Thermal Processing and the Effect of the Viscosity Ratio of Blend Partners

    PubMed Central

    Bärwinkel, Stefanie; Seidel, Andreas; Hobeika, Sven; Hufen, Ralf; Mörl, Michaela; Altstädt, Volker

    2016-01-01

    Morphology formation during compounding, as well as injection molding of blends containing 60 wt % polycarbonate (PC) and 40 wt % polybutadiene rubber-modified styrene-acrylonitrile copolymers (ABS), has been investigated by transmission electron microscopy (TEM). Profiles of the blend morphology have been recorded in injection-molded specimens and significant morphology gradients observed between their skin and core. A <10 µm thick surface layer with strongly dispersed and elongated nano-scale (streak-like) styrene acrylonitrile (SAN) phases and well-dispersed, isolated SAN-grafted polybutadiene rubber particles is followed by a 50–150 µm thick skin layer in which polymer morphology is characterized by lamellar SAN/ABS phases. Thickness of these lamellae increases with the distance from the specimen’s surface. In the core of the specimens the SAN-grafted polybutadiene rubber particles are exclusively present within the SAN phases, which exhibit a much coarser and less oriented, dispersed morphology compared to the skin. The effects of the viscosity of the SAN in the PC/ABS blends on phase morphologies and correlations with fracture mechanics in tensile and impact tests were investigated, including scanning electron microscopy (SEM) assessment of the fracture surfaces. A model explaining the mechanisms of morphology formation during injection molding of PC/ABS blends is discussed. PMID:28773780

  19. Mixing order of glidant and lubricant – Influence on powder and tablet properties

    PubMed Central

    Pingali, Kalyana; Mendez, Rafael; Lewis, Daniel; Michniak-Kohn, Bozena; Cuitino, Alberto; Muzzio, Fernando

    2014-01-01

    The main objective of the present work was to study the effect of mixing order of Cab-O-Sil (CS) and magnesium stearate (MgSt) and microlayers during mixing on blend and tablet properties. A first set of pharmaceutical blend containing Avicel PH200, Pharmatose and micronized acetaminophen was prepared with three mixing orders (mixing order-1: CS added first; mixing order-2: MgSt added first; mixing order-3: CS and MgSt added together). All the blends were subjected to a shear rate of 80 rpm and strain of 40, 160 and 640 revolutions in a controlled shear environment resulting in nine different blends. A second set of nine blends was prepared by replacing Avicel PH200 with Avicel PH102. A total of eighteen blends thus prepared were tested for powder hydrophobicity, powder flow, tablet weight, tablet hardness and tablet dissolution. Results indicated that powder hydrophobicity increased significantly for mixing order-1. Intermediate hydrophobic behavior was found for mixing order-3. Additionally, mixing order 1 resulted in improved powder flow properties, low weight variability, higher average tablet weight and slow drug release rates. Dissolution profiles obtained were found to be strongly dependent not only on the mixing order of flowing agents, but also on the strain and the resulting hydrophobicity. PMID:21356286

  20. Modeling strategies for pharmaceutical blend monitoring and end-point determination by near-infrared spectroscopy.

    PubMed

    Igne, Benoît; de Juan, Anna; Jaumot, Joaquim; Lallemand, Jordane; Preys, Sébastien; Drennen, James K; Anderson, Carl A

    2014-10-01

    The implementation of a blend monitoring and control method based on a process analytical technology such as near infrared spectroscopy requires the selection and optimization of numerous criteria that will affect the monitoring outputs and expected blend end-point. Using a five component formulation, the present article contrasts the modeling strategies and end-point determination of a traditional quantitative method based on the prediction of the blend parameters employing partial least-squares regression with a qualitative strategy based on principal component analysis and Hotelling's T(2) and residual distance to the model, called Prototype. The possibility to monitor and control blend homogeneity with multivariate curve resolution was also assessed. The implementation of the above methods in the presence of designed experiments (with variation of the amount of active ingredient and excipients) and with normal operating condition samples (nominal concentrations of the active ingredient and excipients) was tested. The impact of criteria used to stop the blends (related to precision and/or accuracy) was assessed. Results demonstrated that while all methods showed similarities in their outputs, some approaches were preferred for decision making. The selectivity of regression based methods was also contrasted with the capacity of qualitative methods to determine the homogeneity of the entire formulation. Copyright © 2014. Published by Elsevier B.V.

  1. Habituation in Frankliniella occidentalis to deterrent plant compounds and their blends.

    PubMed

    Egger, Barbara; Spangl, Bernhard; Koschier, Elisabeth Helene

    2014-06-01

    Feeding and oviposition deterrence of three secondary plant compounds and their 1:1 blends to adult female Frankliniella occidentalis Pergande (Thysanoptera: Thripidae) and the potential for habituation of the thrips to the pure compounds and the 1:1 blends at various concentrations were investigated. In choice assays, we tested dose-dependent feeding and oviposition deterrence of the two fatty acid derivatives methyl jasmonate and cis -jasmone, the phenylpropanoid allylanisole, and their blends when directly applied to bean leaf discs. The concentration required to reduce the feeding damage by 50% relative to the control treatment (FDC 50 ) was lowest for cis -jasmone and highest for allylanisole. The feeding deterrent effect of both jasmonates was increased when blended with allylanisole. Feeding deterrence and oviposition deterrence were strongly correlated. In no-choice assays conducted over four consecutive days, we discovered that dilutions at low concentrations (FDC 15 ) applied to bean leaves resulted in habituation to the deterrents, whereas no habituation occurred at higher concentrations (FDC 50 ). We observed a tendency that the 1:1 blends reduce the probability that thrips habituate to the deterrent compounds. Our results may be useful in the development of integrated crop protection strategies with the implementation of allelochemicals as pest behaviour-modifying agents.

  2. Strong and biocompatible three-dimensional porous silk fibroin/graphene oxide scaffold prepared by phase separation.

    PubMed

    Wang, Shu-Dong; Ma, Qian; Wang, Ke; Ma, Pi-Bo

    2018-05-01

    Silk fibroin (SF) is blended with graphene oxide (GO) to prepare the strong and biocompatible three dimensional porous SF/GO blended scaffold via phase separation. GO could be well dispersed in SF solution and GO could also be well distributed in the SF scaffold. Furthermore, the introduction of GO can lead to structural change in the bended scaffold. Higher concentration of GO resulted in more compact structure and smaller pore size of the composite scaffolds without decreasing their porosity. Scanning electron microscopy and energy dispersive spectrometry results also reveal that SF and GO are homogeneous blended together. Analysis of chemical structures of the scaffold shows that addition of GO do not affect the crystalline structure of SF and it is evenly blended with SF. The blended scaffold has significantly higher breaking strength than the pure SF scaffold. In vitro study indicates that both pure SF scaffold and SF/GO composite scaffold support growth and proliferation of MC3T3-E1 osteoprogenitor cells. However, the addition of GO contribute to the proliferation of MC3T3-E1 osteoprogenitor. The testing results show that the blended scaffold is an appropriate candidate for tissue engineering. Copyright © 2018 Elsevier B.V. All rights reserved.

  3. Improved blend and tablet properties of fine pharmaceutical powders via dry particle coating.

    PubMed

    Huang, Zhonghui; Scicolone, James V; Han, Xi; Davé, Rajesh N

    2015-01-30

    The improvements in the flow and packing of fine pharmaceutical powder blends due to dry coating of micronized acetaminophen (mAPAP, ∼11μm), a model poorly flowing drug, are quantified. Poor flow and packing density of fine excipients (∼20μm) allowed testing the hypothesis that dry coating of cohesive API may counteract poor flow and packing of fine pharmaceutical powder blends. Further, fine excipients could improve compaction and reduce segregation tendency. It was found that flow function coefficient (FFC) and bulk density enhancements for 10%, 30%, and 60% (w/w), API loading blends with dry coated API are significantly higher than those without coated silica. At the highest API loading, for which coarser excipients were also used as reference, the flow and packing of dry coated mAPAP blends were significantly increased regardless of the excipient particle size, exceeding those of a well compacting excipient, Avicel 102. In addition, tensile strength of tablets with fine excipients was significantly higher, indicating improved compactibility. These results show for the first time that dry coating of fine, cohesive API powder leads to significantly improved flow and packing of high API loading blends consisting of fine excipients, while achieving improved tablet compactibility, suggesting suitability for direct compaction. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. Acute aquatic toxicity and biodegradation potential of biodiesel fuels

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Haws, R.A.; Zhang, X.; Marshall, E.A.

    1995-12-31

    Recent studies on the biodegradation potential and aquatic toxicity of biodiesel fuels are reviewed. Biodegradation data were obtained using the shaker flask method observing the appearance of CO{sub 2} and by observing the disappearance of test substance with gas chromatography. Additional BOD{sub 5} and COD data were obtained. The results indicate the ready biodegradability of biodiesel fuels as well as the enhanced co-metabolic biodegradation of biodiesel and petroleum diesel fuel mixtures. The study examined reference diesel, neat soy oil, neat rape oil, and the methyl and ethyl esters of these vegetable oils as well as various fuel blends. Acute toxicitymore » tests on biodiesel fuels and blends were performed using Oncorhynchus mykiss (Rainbow Trout) in a static non-renewal system and in a proportional dilution flow replacement system. The study is intended to develop data on the acute aquatic toxicity of biodiesel fuels and blends under US EPA Good Laboratory Practice Standards. The test procedure is designed from the guidelines outlined in Methods for Measuring the Acute Toxicity of Effluents and Receiving Waters to Freshwater and Marine Organisms and the Fish Acute Aquatic Toxicity Test guideline used to develop aquatic toxicity data for substances subject to environmental effects test regulations under TSCA. The acute aquatic toxicity is estimated by an LC50, a lethal concentration effecting mortality in 50% of the test population.« less

  5. At the foot of the smoking mountains: The 2014 scientific investigations in the Islands of the Four Mountains

    USGS Publications Warehouse

    Hatfield, Virginia; Bruner, Kale; West, Dixie; Savinetsky, Arkady; Krylovich, Olga; Khasanov, Bulat; Vasyukov, Dmitry; Antipushina, Zhanna; Okuno, Mitsuru; Crockford, Susan; Nicolaysen, Kirsten; MacInnes, Breanyn; Persico, Lyman; Izbekov, Pavel; Neal, Christina; Bartlett, Thomas; Loopesko, Lydia; Fulton, Anne

    2016-01-01

    An interdisciplinary research team conducted archaeological, geological, and biological investigations in the Islands of the Four Mountains, Alaska during the summer of 2014 as part of a three-year project to study long-term geological and ecological patterns and processes with respect to human settlement. Researchers investigated three archaeological sites on Chuginadak Island (SAM-0014, SAM-0016 and SAM-0047) and two archaeological sites on Carlisle Island (AMK-0003 and SAM-0034) as well as peat, tephra, and lava deposition on those islands. These investigations resulted in the delineation of archaeological sites, documentation of geological and cultural stratigraphy, excavation of house-pit features, visual characterization and sampling of potential lithic sources, and documentation of Unangan occupation in the Islands of the Four Mountains from roughly 3,800 years ago to Russian contact.

  6. Flight and Test-stand Investigation of High-performance Fuels in Modified Double-row Radial Air-cooled Engines III: Knock-limited Performance of 33-R as Compared with a Triptane Blend and 28-R in Flight

    NASA Technical Reports Server (NTRS)

    Blackman, Calvin C.; White, H. Jack

    1945-01-01

    A comparison has been made in flight of the antiknock characteristics of 33-R fuel with that of 28-R and a triptane blent. The knock-limited performance of the three fuels - 33-R, a blend of 80 percent 28-R plus 20 percent triptane (leaded to 4.5 ml TEL/gal), and 28-R - was investigated in two modified 14-cylinder double-row radial air-cooled engines. Tests were conducted on the engines as installed in the left inboard nacelle of an airplane. A carburetor-air temperature of approximately 85 deg F was maintained. The conditions covered at an engine speed of 2250 rpm were high and low blower ratios and spark advances of 25 deg and 32 deg B.T.C. For an engine speed of 1800 rpm only the high-blower condition was investigated for both 25 deg and 32 deg spark advances. For the conditions investigated the difference between 33-R and the triptane blend was found to be slight; the performance of 33-R fuel, however, was slightly higher than that of the triptane blend in the lean region. The knock-limited power obtained with the 33-R fuel was from 14 to 28 percent higher than that of the 28-R fuel for the entire range of test conditions; the greatest improvement was shown in the lean region.

  7. TANK 21 AND TANK 24 BLEND AND FEED STUDY: BLENDING TIMES, SETTLING TIMES, AND TRANSFERS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lee, S.; Leishear, R.; Poirier, M.

    2012-05-31

    The Salt Disposition Integration (SDI) portfolio of projects provides the infrastructure within existing Liquid Waste facilities to support the startup and long term operation of the Salt Waste Processing Facility (SWPF). Within SDI, the Blend and Feed Project will equip existing waste tanks in the Tank Farms to serve as Blend Tanks where salt solutions of up to 1.2 million gallons will be blended in 1.3 million gallon tanks and qualified for use as feedstock for SWPF. In particular, Tanks 21 and 24 are planned to be used for blending and transferring to the SDI feed tank. These tanks weremore » evaluated here to determine blending times, to determine a range of settling times for disturbed sludge, and to determine that the SWPF Waste Acceptance Criteria that less than 1200 mg/liter of solids will be entrained in salt solutions during transfers from the Tank 21 and Tank 24 will be met. Overall conclusions for Tank 21 and Tank 24 operations include: (1) Experimental correction factors were applied to CFD (computational fluid dynamics) models to establish blending times between approximately two and five hours. As shown in Phase 2 research, blending times may be as much as ten times greater, or more, if lighter fluids are added to heavier fluids (i.e., water added to salt solution). As the densities of two salt solutions converge this effect may be minimized, but additional confirmatory research was not performed. (2) At the current sludge levels and the presently planned operating heights of the transfer pumps, solids entrainment will be less than 1200 mg/liter, assuming a conservative, slow settling sludge simulant. (3) Based on theoretical calculations, particles in the density range of 2.5 to 5.0 g/mL must be greater than 2-4 {micro}m in diameter to ensure they settle adequately in 30-60 days to meet the SWPF feed criterion (<1200 mg/l). (4) Experimental tests with sludge batch 6 simulant and field turbidity data from a recent Tank 21 mixing evolution suggest the solid particles have higher density and/or larger size than indicated by previous analysis of SRS sludge and sludge simulants. (5) Tank 21 waste characterization, laboratory settling tests, and additional field turbidity measurements during mixing evolutions are recommended to better understand potential risk for extended (> 60 days) settling times in Tank 21.« less

  8. Comparable postprandial glucose reductions with viscous fiber blend enriched biscuits in healthy subjects and patients with diabetes mellitus: acute randomized controlled clinical trial.

    PubMed

    Jenkins, Alexandra L; Jenkins, David J A; Wolever, Thomas M S; Rogovik, Alexander L; Jovanovski, Elena; Bozikov, Velimir; Rahelić, Dario; Vuksan, Vladimir

    2008-12-01

    To compare the blood glucose-lowering effect of a highly viscous fiber blend (VFB) added to a starchy snack on postprandial glycemia between healthy participants and participants with diabetes mellitus. Ten healthy participants (4 men and 6 women, aged 28+/-2.6 years, body mass index [BMI], 24.3+/-0.8 kg/m(2)) and 9 participants with diabetes mellitus type 2 (3 men and 6 women, aged 68+/-3.8 years, BMI 28.8+/-1.2 kg/m(2)) on four separate occasions took either 50 g available carbohydrates as control biscuits, biscuits with 10 g of highly viscous fiber blend, white bread with 12 g of margarine, or white bread alone. Postprandial blood glucose response, glycemic index (GI), and palatability were determined. Mean (95% confidence interval) GI values of the viscous fiber blend biscuits were 26 (16-36) and 37 (27-47) GI units for healthy participants and participants with diabetes mellitus, respectively. These values were significantly lower than those of white bread, white bread with 12 g of margarine, and control biscuits (P<0.001, paired t test) both in healthy participants (GI 100, 108 [57-159], and 101 [44-158], respectively) and participants with diabetes mellitus (GI 100, 103 [79-127], and 94 [78-110], respectively). Viscous fiber blend significantly reduced the glycemic index by 74% (7.4 GI units/g of fiber) in healthy participants and by 63% (6.3 GI units/g of fiber) in participants with diabetes. The GI did not differ between control meals in both healthy participants and participants with diabetes. There were no significant differences in palatability among the types of meals, although participants with diabetes found the viscous fiber blend biscuits more palatable (P=0.002, t test). Viscous fiber blend is a very potent and palatable soluble fiber addition to a starchy snack, which is able to reduce the glycemic response to a similar extent in both healthy participants and individuals with diabetes mellitus. Biscuits with low GI, and possibly other viscous fiber blend fortified starchy foods, may potentially be a useful replacement of high GI snack foods in the diet.

  9. PVDF-based semicrystalline-amorphous blends: Phase behavior and thermomechanical properties

    NASA Astrophysics Data System (ADS)

    Campo, Cheryl Josephine

    Poly(vinylidene fluoride) [PVDF]-based semicrystalline-amorphous blends were studied to better understand the degree to which transition temperatures and mechanical properties could be varied as a function of composition. Changes in the amorphous component, processing parameters, MW, and filler content were used to manipulate blend properties. Compositional and MW series of PVDF:poly(vinyl acetate) [PVAc] blends were prepared and characterized. Varying PVDF content led to appreciable changes in crystallinity. In contrast, the effect of composition on blend glass transition temperature, Tg, was manifested only at low PVDF contents. The effect of MWPVA, on the 30:70 PVDF:PVAc composition was manifested primarily in the materials' viscoelastic response to deformation. Ternary blends of PVDF, PVAc, and poly(methyl methacrylate) [PMMA] showed limited miscibility with both a PVAc- and PMMA-rich amorphous phase apparent in all the compositions tested. PVDF:PMMA blends on the other hand exhibited good miscibility characterized by tunable Tg values which were further exploited by varying the processing conditions in order to obtain thermomechanical properties ideal for bio-related shape memory applications. PVDF:poly(ethyl methacrylate) [PEMA] blends, despite having very broad transitions, similarly exhibited desirable transition temperatures for in vivo actuation. The effect of boron nitride (BN), short carbon fibers (SCF), and clay on blend properties was also assessed. SCF filler in 50:50 PVDF:PMMA led mainly to the formation of PVDF crystals in the alpha form, clay was observed to promote growth of the beta crystal form, and BN led to a mixture of crystal forms. BN also exhibited interesting effects in the creep behavior of this system as well as the crystallization behavior of the 50:50 PVDF:PEMA blend, suppressed kinetic crystallization competing with enhanced nucleation effect under isothermal conditions observed in the latter. Depending on the processing conditions used, SCF was found to have similar nucleation effects in the 50:50 PVDF:PMMA blend but diminished degrees of crystallinity overall. Finally, shape memory behavior of PVDF:PVAc blends as well as SCF-filled 50:50 PVDF:PMMA was characterized using single and multiple shape memory cycles. Increasing PVDF content had a negative impact on PVDF:PVAc shape memory properties while increasing stress was found to have an enhancing effect as did low SCF filler content in 50:50 PVDF:PMMA.

  10. The chocolate-colored expanse of Rogers Dry Lake frames the sleek lines of the Boeing / NASA X-48B subscale demonstrator during a test flight at Edwards AFB

    NASA Image and Video Library

    2007-08-14

    Boeing Phantom Works' subscale Blended Wing Body technology demonstration aircraft began its initial flight tests from NASA's Dryden Flight Research Center at Edwards Air Force Base, Calif. in the summer of 2007. The 8.5 percent dynamically scaled unmanned aircraft, designated the X-48B by the Air Force, is designed to mimic the aerodynamic characteristics of a full-scale large cargo transport aircraft with the same blended wing body shape. The initial flight tests focused on evaluation of the X-48B's low-speed flight characteristics and handling qualities. About 25 flights were planned to gather data in these low-speed flight regimes. Based on the results of the initial flight test series, a second set of flight tests was planned to test the aircraft's low-noise and handling characteristics at transonic speeds.

  11. Approach for energy saving and pollution reducing by fueling diesel engines with emulsified biosolution/ biodiesel/diesel blends.

    PubMed

    Lin, Yuan-Chung; Lee, Wen-Jhy; Chao, How-Ran; Wang, Shu-Li; Tsou, Tsui-Chun; Chang-Chien, Guo-Ping; Tsai, Perng-Jy

    2008-05-15

    The developments of both biodiesel and emulsified diesel are being driven by the need for reducing emissions from diesel engines and saving energy. Artificial chemical additives are also being used in diesel engines for increasing their combustion efficiencies. But the effects associated with the use of emulsified additive/biodiesel/diesel blends in diesel engines have never been assessed. In this research, the premium diesel fuel (PDF) was used as the reference fuel. A soy-biodiesel was selected as the test biodiesel. A biosolution made of 96.5 wt % natural organic enzyme-7F (NOE-7F) and 3.5 wt % water (NOE-7F water) was used as the fuel additive. By adding additional 1 vol % of surfactant into the fuel blend, a nanotechnology was used to form emulsified biosolution/soy-biodiesel/PDF blends for fueling the diesel engine. We found that the emulsified biosolution/soy-biodiesel/PDF blends did not separate after being kept motionless for 30 days. The above stability suggests that the above combinations are suitable for diesel engines as alternative fuels. Particularly, we found that the emulsified biosolution/soy-biodiesel/PDF blends did have the advantage in saving energy and reducing the emissions of both particulate matters (PM) and polycyclic aromatic hydrocarbons (PAHs) from diesel engines as compared with PDF, soy-biodiesel/PDF blends, and emulsified soy-biodiesel/ PDF blends. The results obtained from this study will provide useful approaches for reducing the petroleum reliance, pollution, and global warming. However, it should be noted that NO(x) emissions were not measured in the present study which warrants the need for future investigation.

  12. Combustion behaviors and kinetics of sewage sludge blended with pulverized coal: With and without catalysts.

    PubMed

    Wang, Zhiqiang; Hong, Chen; Xing, Yi; Li, Yifei; Feng, Lihui; Jia, Mengmeng

    2018-04-01

    The combustion behaviors of sewage sludge (SS), pulverized coal (PC), and their blends were studied using a thermogravimetric analyzer. The effect of the mass ratio of SS to PC on the co-combustion characteristics was analyzed. The experiments showed that the ignition performance of the blends improved significantly as the mass percentage of SS increased, but its combustion intensity decreased. The burnout temperature (T b ) and comprehensive combustibility index (S) of the blends were almost unchanged when the mass percentage of SS was less than 10%. However, a high mass percentage of SS (>10%) resulted in a great increase in T b and a notable decrease in S. Subsequently, the effects of different catalysts (CaO, CeO 2 , MnO 2 , and Fe 2 O 3 ) on the combustion characteristics and activation energy of the SS/PC blend were investigated. The four catalysts promoted the release and combustion of volatile matters in the blended fuels and shifted their combustion profiles to a low temperature. In addition, their peak separating tendencies were obvious at 350-550 C, resulting in high peak widths. All the catalysts improved combustion activity of the blended fuel and accelerated fixed carbon combustion, which decreased the ignition temperature and burnout temperature of the fuels. CeO 2 had the best catalytic effects in terms of the comprehensive combustion performance and activation energy, followed closely by Fe 2 O 3 . However, the rare-earth compounds are expensive to be applied in the catalytic combustion process of SS/PC blend at present. Based on both catalytic effects and economy, Fe 2 O 3 was potentially an optimal option for catalytic combustion among the tested catalysts. Copyright © 2018 Elsevier Ltd. All rights reserved.

  13. Fiber-Content Measurement of Wool-Cashmere Blends Using Near-Infrared Spectroscopy.

    PubMed

    Zhou, Jinfeng; Wang, Rongwu; Wu, Xiongying; Xu, Bugao

    2017-10-01

    Cashmere and wool are two protein fibers with analogous geometrical attributes, but distinct physical properties. Due to its scarcity and unique features, cashmere is a much more expensive fiber than wool. In the textile production, cashmere is often intentionally blended with fine wool in order to reduce the material cost. To identify the fiber contents of a wool-cashmere blend is important to quality control and product classification. The goal of this study is to develop a reliable method for estimating fiber contents in wool-cashmere blends based on near-infrared (NIR) spectroscopy. In this study, we prepared two sets of cashmere-wool blends by using either whole fibers or fiber snippets in 11 different blend ratios of the two fibers and collected the NIR spectra of all the 22 samples. Of the 11 samples in each set, six were used as a subset for calibration and five as a subset for validation. By referencing the NIR band assignment to chemical bonds in protein, we identified six characteristic wavelength bands where the NIR absorbance powers of the two fibers were significantly different. We then performed the chemometric analysis with two multilinear regression (MLR) equations to predict the cashmere content (CC) in a blended sample. The experiment with these samples demonstrated that the predicted CCs from the MLR models were consistent with the CCs given in the preparations of the two sample sets (whole fiber or snippet), and the errors of the predicted CCs could be limited to 0.5% if the testing was performed over at least 25 locations. The MLR models seem to be reliable and accurate enough for estimating the cashmere content in a wool-cashmere blend and have potential to be used for tackling the cashmere adulteration problem.

  14. A comparison between the effects of gamma radiation and sulfur cure system on the microstructure and crosslink network of (styrene butadiene rubber/ethylene propylene diene monomer) blends in presence of nanoclay

    NASA Astrophysics Data System (ADS)

    Shoushtari Zadeh Naseri, Aida; Jalali-Arani, Azam

    2015-10-01

    Rubber blends based on (styrene-butadiene rubber (SBR)/ethylene-propylene-diene monomer (EPDM)) with and without organoclay (OC) were prepared through a melt mixing process. The concentration ratio of the rubber phases (EPDM/SBR; 50/50 wt%) and the amount of the OC were kept constant. The samples were then vulcanized by means of gamma radiation using a Co-60 gamma source as well as sulfur cure system. The effect of absorbed dose on the formation of the crosslinks was confirmed by the Fourier transform infrared spectroscopy (FTIR). The effects of absorbed dose, sulfur cure system and OC on the gel content, and crosslink density were evaluated by the chemical tests. Applying the Charlesby-Pinner equation to estimate the radiation chemical yield, revealed that the use of OC in the blend caused 20% reduction in the degradation/crosslinking ratio. Employing the swelling test data, some thermodynamic parameters were determined. Using field emission scanning electron microscopy (FE-SEM) to investigate microstructure of the samples revealed a more homogeneous structure and also an increase in compatibility of the blend components in the sample cured by the irradiation in comparison to that cured by the sulfur curing system.

  15. The combination of two novel tobacco blends and filter technologies to reduce the in vitro genotoxicity and cytotoxicity of prototype cigarettes.

    PubMed

    Crooks, Ian; Scott, Ken; Dalrymple, Annette; Dillon, Debbie; Meredith, Clive

    2015-04-01

    Tobacco smoke from a combustible cigarette contains more than 6000 constituents; approximately 150 of these are identified as toxicants. Technologies that modify the tobacco blend to reduce toxicant emissions have been developed. These include tobacco sheet substitute to dilute toxicants in smoke and blend treated tobacco to reduce the levels of nitrogenous precursors and some polyphenols. Filter additives to reduce gas (vapour) phase constituents have also been developed. In this study, both tobacco blend and filter technologies were combined into an experimental cigarette and smoked to International Organisation on Standardisation and Health Canada puffing parameters. The resulting particulate matter was subjected to a battery of in vitro genotoxicity and cytotoxicity assays - the Ames test, mouse lymphoma assay, the in vitro micronucleus test and the Neutral Red Uptake assay. The results indicate that cigarettes containing toxicant reducing technologies may be developed without observing new additional genotoxic hazards as assessed by the assays specified. In addition, reductions in bacterial mutagenicity and mammalian genotoxicity of the experimental cigarette were observed relative to the control cigarettes. There were no significant differences in cytotoxicity relative to the control cigarettes. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  16. FR Performance of New Fire-off on PET/CO blend fabrics

    NASA Astrophysics Data System (ADS)

    Atakan, R.; Çelebi, E.; Ozcan, G.; Soydan, N.; Sarac, A. S.

    2017-10-01

    This paper represents the investigation on flame retardancy performance and durability of polyester/cotton (P/C) fabrics treated with a novel halogen/formaldehyde free, P-N synergetic FR finishing agent called New Fire-off. 100 % Cotton, 100 % Polyester and three different blend P/C fabrics were chosen in this study. Fabric samples were treated with New Fire-off through pad-dry-cure process. Flammability and thermal properties of the treated samples with New Fire-off were tested according to relevant ISO standard and procedures. The obtained results showed that this new finishing formulation is a good char-forming agent. However, further studies are required to achieve washing durability for the P/C blends.

  17. Viability and Biomechanics of Diced Cartilage Blended With Platelet-Rich Plasma and Wrapped With Poly (Lactic-Co-Glycolic) Acid Membrane.

    PubMed

    Liao, Jun-Lin; Chen, Jia; He, Bin; Chen, Yong; Xu, Jia-Qun; Xie, Hong-Ju; Hu, Feng; Wang, Ai-Jun; Luo, ChengQun; Li, Qing-Feng; Zhou, Jian-Da

    2017-09-01

    The objective of this study was to investigate the viability and biomechanics of diced cartilage blended with platelet-rich plasma (PRP) and wrapped with poly (lactic-co-glycolic) acid (PLGA) membrane in a rabbit model. A total of 10 New Zealand rabbits were used for the study. Cartilage grafts were harvested from 1 side ear. The grafts were divided into 3 groups for comparison: bare diced cartilage, diced cartilage wrapped with PLGA membrane, and diced cartilage blended with PRP and wrapped with PLGA membrane. Platelet-rich plasma was prepared using 8 mL of auricular blood. Three subcutaneous pockets were made in the backs of the rabbits, and the grafts were placed in these pockets. The subcutaneous implant tests were conducted for safety assessment of the PLGA membrane in vivo. All of the rabbits were sacrificed at the end of 3 months, and the specimens were collected. The sections were stained with hematoxylin and eosin, toluidin blue, and collagen II immunohistochemical. Simultaneously, biomechanical properties of grafts were assessed. This sample of PLGA membrane was conformed to the current standard of biological evaluation of medical devices. Moderate resorption was seen at the end of 3 months in the gross assessment in diced cartilage wrapped with PLGA membrane, while diced cartilage blended with PRP had no apparent resorption macroscopically and favorable viability in vivo after 3 months, and the histological parameters supported this. Stress-strain curves for the compression test indicated that the modulus of elasticity of bare diced cartilage was 7.65 ± 0.59 MPa; diced cartilage wrapped with PLGA membrane was 5.98 ± 0.45 MPa; and diced cartilage blended with PRP and wrapped with PLGA membrane was 7.48 ± 0.55 MPa, respectively. Diced cartilage wrapped with PLGA membrane had moderate resorption macroscopically after 3 months. However, blending with PRP has beneficial effects in improving the viability of diced cartilages. Additionally, the compression modulus of diced cartilage blended with PRP and wrapped with PLGA membrane was similar to bare diced cartilage.

  18. Experimental study on particulate and NOx emissions of a diesel engine fueled with ultra low sulfur diesel, RME-diesel blends and PME-diesel blends.

    PubMed

    Zhu, Lei; Zhang, Wugao; Liu, Wei; Huang, Zhen

    2010-02-01

    Ultra low sulfur diesel and two different kinds of biodiesel fuels blended with baseline diesel fuel in 5% and 20% v/v were tested in a Cummins 4BTA direct injection diesel engine, with a turbocharger and an intercooler. Experiments were conducted under five engine loads at two steady speeds (1500 rpm and 2500 rpm). The study aims at investigating the engine performance, NO(x) emission, smoke opacity, PM composition, PM size distribution and comparing the impacts of low sulfur content of biodiesel with ULSD on the particulate emission. The results indicate that, compared to base diesel fuel, the increase of biodiesel in blends could cause certain increase in both brake specific fuel consumption and brake thermal efficiency. Compared with baseline diesel fuel, the biodiesel blends bring about more NO(x) emissions. With the proportion of biodiesel increase in blends, the smoke opacity decreases, while total particle number concentration increases. Meanwhile the ULSD gives lower NO(x) emissions, smoke opacity and total number concentration than those of baseline diesel fuel. In addition, the percentages of SOF and sulfate in particulates increase with biodiesel in blends, while the dry soot friction decreases obviously. Compared with baseline diesel fuel, the biodiesel blends increase the total nucleation number concentration, while ULSD reduces the total nucleation number concentration effectively, although they all have lower sulfur content. It means that, for ULSD, the lower sulfur content is the dominant factor for suppressing nucleation particles formation, while for biodiesel blends, lower volatile, lower aromatic content and higher oxygen content of biodiesel are key factors for improving the nucleation particles formation. The results demonstrate that the higher NO(x) emission and total nucleation number concentration are considered as the big obstacles of the application of biodiesel in diesel engine. Copyright 2009 Elsevier B.V. All rights reserved.

  19. Dispensing Equipment Testing with Mid-Level Ethanol/Gasoline Test Fluid: Summary Report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Boyce, K.; Chapin, J. T.

    The National Renewable Energy Laboratory's (NREL) Nonpetroleum-Based Fuel Task addresses the hurdles to commercialization of biomass-derived fuels and fuel blends. One such hurdle is the unknown compatibility of new fuels with current infrastructure, such as the equipment used at service stations to dispense fuel into automobiles. The U.S. Department of Energy's (DOE) Vehicle Technology Program and the Biomass Program have engaged in a joint project to evaluate the potential for blending ethanol into gasoline at levels higher than nominal 10 volume percent. This project was established to help DOE and NREL better understand any potentially adverse impacts caused by amore » lack of knowledge about the compatibility of the dispensing equipment with ethanol blends higher than what the equipment was designed to dispense. This report provides data about the impact of introducing a gasoline with a higher volumetric ethanol content into service station dispensing equipment from a safety and a performance perspective.« less

  20. Analysis of performance and emissions of diesel engine using sunflower biodiesel

    NASA Astrophysics Data System (ADS)

    Tutunea, Dragos; Dumitru, Ilie

    2017-10-01

    The world consumption of fossil fuels is increasing rapidly and it affects the environment by green house gases causing health hazards. Biodiesel is emerging as an important promising alternative energy resource which can be used to reduce or even replace the usage of petroleum. Since is mainly derived from vegetable oil or animal fats can be produce for large scale by local farmers offering a great choice. However the extensive utilization of the biofuels can lead to shortages in the food chain. This paper analyzed the sunflower methyl ester (SFME) and its blends as an alternate source of fuel for diesel engines. Biodiesel was prepared from sunflower oil in laboratory in a small biodiesel installation (30L) by base transesterification. A 4 cylinder Deutz F4L912 diesel engine was used to perform the tests on various blends of sunflower biodiesel. The emissions of CO, HC were lower than diesel fuel for all blends tested. The NOx emissions were higher due to the high volatility and high viscosity of biodiesel.

  1. Nanostructured and Conventional Cr2O3, TiO2, and TiO2-Cr2O3 Thermal-Sprayed Coatings for Metal-Seated Ball Valve Applications in Hydrometallurgy

    NASA Astrophysics Data System (ADS)

    Vernhes, Luc; Bekins, Craig; Lourdel, Nicolas; Poirier, Dominique; Lima, Rogerio S.; Li, Duanjie; Klemberg-Sapieha, Jolanta E.

    2016-06-01

    A detailed characterization project was undertaken by Velan, an international industrial valve designer and manufacturer, in collaboration with the National Research Council of Canada, Boucherville, and Polytechnique Montréal. The purpose was to assess the mechanical and tribological resistances of promising ceramic coatings for hydrometallurgy applications, including a novel n-TiO2-Cr2O3 blend. Hardness and shear strength were determined using microhardness indentation testers and universal tensile testing equipment. Wear resistance of the coatings under sliding wear, abrasion, and galling conditions were measured by standard pin-on-disk tests, abrasion tests, and custom-designed galling tests. The main result is that the synergy between Cr2O3 and n-TiO2 produced abrasion performance exceeding that of these materials alone. Also, an optimized balance between the hard and brittle Cr2O3 phases and the soft and ductile n-TiO2 phases resulted in higher abrasion, sliding, and galling resistance. The novel n-TiO2-Cr2O3 blend is therefore considered as a promising evolution of the current TiO2-Cr2O3 blend.

  2. Effect of chain extension on rheology and tensile properties of PHB and PHB-PLA blends

    NASA Astrophysics Data System (ADS)

    Bousfield, Glenn

    Poly(3-hydroxybutyrate), referred to as PHB, is a bacterially-synthesized and biodegradable polymer which is being considered as a substitute for non-biodegradable bulk polymers like polypropylene. PHB is naturally extremely isotactic and naturally has a very high degree of crystallinity, resulting in a stiff but brittle material. The stability of PHB crystals also means that the melting point of the polymer is approximately 170°C, high with respect to similar polymers. For instance, the melting point of poly(4-hydroxybutyrate) is only 53°C (Saito, Nakamura, Hiramitsu, & Doi, 1996). Above 170°C, PHB is subject to a thermomechanical degradation mechanism, meaning that the polymer cannot be melted without degrading. One possible solution to the problem of degradation is to add a chain extender to the molten polymer to increase average molecular weight to counteract the molecular weight lost to degradation. In this work, a variety of chain extenders (JoncrylRTM ADR 4368-C, pyromellitic dianhydride, hexamethylene diisocyanate, polycarbodiimide) were compounded with a random copolymer of 98 mol% 3-hydroxybutyrate and 2 mol% 3-hydroxyvalerate (referred to as PHB) in concentrations ranging from 0.25% to 4%, to determine which chain extender functionality worked best with PHB. Molecular weight change was inferred from torque monitored during compounding, and from complex viscosity determined from parallel-plate rheology. None of the chain extenders changed the rate of degradation of PHB, although Joncryl increased the complex viscosity of the polymer. PHB was also blended with Poly(L-lactic acid), referred to as PLLA in PHB/PLLA ratios of 100/0, 75/25, 50/50, 25/75 and 0/100, to determine the effect of blending on the thermal stability of PHB. Again, thermal stability was determined by monitoring torque during compounding and by measuring complex viscosity through parallel-plate rheology. Blends in which PHB was the more abundant phase, as well as the 50% PHB/50% PLA blend continued to degrade, and the PLLA did not in these cases significantly increase complex viscosity. By contrast, the 25/75 PHB/PLLA blend had a complex viscosity equal to the neat PLLA blend, and both of the blends remained stable. All five blends were also produced with 1% Joncryl to observe the effect of Joncryl on the blends. In the 50/50 blend and the blends in which PLLA was the major component, complex viscosity increased by at least an order of magnitude, while in the 75/25 PHB/PLLA blend and the neat PHB blend, the effect of Joncryl was to increase complex viscosity only by a factor of 2. The effect of blending and of Joncryl on PHB-PLA blends was further investigated through uniaxial tensile stress testing of compression moulded samples of the blends, neat and with 1% Joncryl. The results showed an increase in tensile stress at yield and tensile strain at break for blends with the addition of Joncryl, although Young's modulus was somewhat diminished for these blends. In conclusion, chain extenders were not effective in reversing the effect of thermomechanical degradation, possibly because they do not change the resistance to bond rotation in PHB chains, or because they are not reactive with acrylates, although the exact cause has not been determined.

  3. Development and Assessment of Plant-Based Synthetic Odor Baits for Surveillance and Control of Malaria Vectors

    PubMed Central

    Nyasembe, Vincent O.; Tchouassi, David P.; Kirwa, Hillary K.; Foster, Woodbridge A.; Teal, Peter E. A.; Borgemeister, Christian; Torto, Baldwyn

    2014-01-01

    Background Recent malaria vector control measures have considerably reduced indoor biting mosquito populations. However, reducing the outdoor biting populations remains a challenge because of the unavailability of appropriate lures to achieve this. This study sought to test the efficacy of plant-based synthetic odor baits in trapping outdoor populations of malaria vectors. Methodology and Principal Finding Three plant-based lures ((E)-linalool oxide [LO], (E)-linalool oxide and (E)-β-ocimene [LO + OC], and a six-component blend comprising (E)-linalool oxide, (E)-β-ocimene, hexanal, β-pinene, limonene, and (E)-β-farnesene [Blend C]), were tested alongside an animal/human-based synthetic lure (comprising heptanal, octanal, nonanal, and decanal [Blend F]) and worn socks in a malaria endemic zone in the western part of Kenya. Mosquito Magnet-X (MM-X) and lightless Centre for Disease Control (CDC) light traps were used. Odor-baited traps were compared with traps baited with either solvent alone or solvent + carbon dioxide (controls) for 18 days in a series of randomized incomplete-block designs of days × sites × treatments. The interactive effect of plant and animal/human odor was also tested by combining LO with either Blend F or worn socks. Our results show that irrespective of trap type, traps baited with synthetic plant odors compared favorably to the same traps baited with synthetic animal odors and worn socks in trapping malaria vectors, relative to the controls. Combining LO and worn socks enhanced trap captures of Anopheles species while LO + Blend F recorded reduced trap capture. Carbon dioxide enhanced total trap capture of both plant- and animal/human-derived odors. However, significantly higher proportions of male and engorged female Anopheles gambiae s.l. were caught when the odor treatments did not include carbon dioxide. Conclusion and Significance The results highlight the potential of plant-based odors and specifically linalool oxide, with or without carbon dioxide, for surveillance and mass trapping of malaria vectors. PMID:24587059

  4. Development and assessment of plant-based synthetic odor baits for surveillance and control of malaria vectors.

    PubMed

    Nyasembe, Vincent O; Tchouassi, David P; Kirwa, Hillary K; Foster, Woodbridge A; Teal, Peter E A; Borgemeister, Christian; Torto, Baldwyn

    2014-01-01

    Recent malaria vector control measures have considerably reduced indoor biting mosquito populations. However, reducing the outdoor biting populations remains a challenge because of the unavailability of appropriate lures to achieve this. This study sought to test the efficacy of plant-based synthetic odor baits in trapping outdoor populations of malaria vectors. Three plant-based lures ((E)-linalool oxide [LO], (E)-linalool oxide and (E)-β-ocimene [LO + OC], and a six-component blend comprising (E)-linalool oxide, (E)-β-ocimene, hexanal, β-pinene, limonene, and (E)-β-farnesene [Blend C]), were tested alongside an animal/human-based synthetic lure (comprising heptanal, octanal, nonanal, and decanal [Blend F]) and worn socks in a malaria endemic zone in the western part of Kenya. Mosquito Magnet-X (MM-X) and lightless Centre for Disease Control (CDC) light traps were used. Odor-baited traps were compared with traps baited with either solvent alone or solvent + carbon dioxide (controls) for 18 days in a series of randomized incomplete-block designs of days × sites × treatments. The interactive effect of plant and animal/human odor was also tested by combining LO with either Blend F or worn socks. Our results show that irrespective of trap type, traps baited with synthetic plant odors compared favorably to the same traps baited with synthetic animal odors and worn socks in trapping malaria vectors, relative to the controls. Combining LO and worn socks enhanced trap captures of Anopheles species while LO + Blend F recorded reduced trap capture. Carbon dioxide enhanced total trap capture of both plant- and animal/human-derived odors. However, significantly higher proportions of male and engorged female Anopheles gambiae s.l. were caught when the odor treatments did not include carbon dioxide. The results highlight the potential of plant-based odors and specifically linalool oxide, with or without carbon dioxide, for surveillance and mass trapping of malaria vectors.

  5. A novel fortified blended flour, corn-soy blend “plus-plus,” is not inferior to lipid-based ready-to-use supplementary foods for the treatment of moderate acute malnutrition in Malawian children12345

    PubMed Central

    LaGrone, Lacey N; Trehan, Indi; Meuli, Gus J; Wang, Richard J; Thakwalakwa, Chrissie; Maleta, Kenneth; Manary, Mark J

    2012-01-01

    Background: Children with moderate acute malnutrition (MAM) are often treated with fortified blended flours, most commonly a corn-soy blend (CSB). However, recovery rates remain <75%, lower than the rate achieved with peanut paste–based ready-to-use supplementary foods (RUSFs). To bridge this gap, a novel CSB recipe fortified with oil and dry skim milk, “CSB++,” has been developed. Objective: In this trial we compared CSB++ with 2 RUSF products for the treatment of MAM to test the hypothesis that the recovery rate achieved with CSB++ will not be >5% worse than that achieved with either RUSF. Design: We conducted a prospective, randomized, investigator-blinded, controlled noninferiority trial involving rural Malawian children aged 6–59 mo with MAM. Children received 75 kcal CSB++ · kg−1 · d−1, locally produced soy RUSF, or an imported soy/whey RUSF for ≤12 wk. Results: The recovery rate for CSB++ (n = 763 of 888; 85.9%) was similar to that for soy RUSF (795 of 806, 87.7%; risk difference: −1.82%; 95% CI: −4.95%, 1.30%) and soy/whey RUSF (807 of 918, 87.9%; risk difference: −1.99%; 95% CI: −5.10%, 1.13%). On average, children who received CSB++ required 2 d longer to recover, and the rate of weight gain was less than that with either RUSF, although height gain was the same among all 3 foods studied. Conclusions: A novel, locally produced, fortified blended flour (CSB++) was not inferior to a locally produced soy RUSF and an imported soy/whey RUSF in facilitating recovery from MAM. The recovery rate observed for CSB++ was higher than that for any other fortified blended flour tested previously. This trial is registered at clinicaltrials.gov as NCT00998517. PMID:22170366

  6. Mechanical properties of PP/PA blends in addition with PP-g-MAH with different PP molecular weight and MAH content

    NASA Astrophysics Data System (ADS)

    Tokumitsu, Katuhisa; Nakajima, Yuki; Aoki, Kenji

    2016-03-01

    The mechanical properties and morphological changes of PP/PA6/PP-g-MAH blends were investigated. In particular, various kinds of PP-g-MAH, which have a series of different Mw of PP and MAH content, were investigated. From the tensile test results of PP/PA6 blends, although the elongation at break and yield stress can be improved by adding PP-g-MAH, modulus slightly decreased. In particular, elongation at break of PP/PA in addition with PP-g-MAH increased twentyfold from 27.0% (without PP-g-MAH) to 570%. On the basis of Charpy impact test results, the impact strength can also be improved by adding PP-g-MAH. From SEM observation, it was found that the diameter of the dispersed PA6 phase in PP matrix was getting much smaller with PP-g-MAH content. From the TEM observation, the boundary of the PA phase in PP/PA blends without PP-g-MAH compatibilizer can be observed clearly, but it becomes hard to see the boundary part of the PA phase in PP/PA blend with compatibilizer. Furthermore, when comparing the inside of the PA phase, small amount of PP phase can be observed in the PA phase of PP/PA blend with compatibilizer. Here, we defined a parameter, Comprehensive Mechanical Property Factor (CMPF), which can be calculated by multiple each mechanical property (elongation at break, yield stress, modulus and impact strength) against each maximum value, and it was found that CMPF has a good correlation with the diameter of PA6 phase. In conclusion, an optimum mechanical property of PP/PA6 can be obtained by using PP-g-MAH with Mw around 35,000 ˜ 50,000 g mol-1 and MAH content around 2.0 ˜ 3.5 %.

  7. Improved algorithms in the CE-QUAL-W2 water-quality model for blending dam releases to meet downstream water-temperature targets

    USGS Publications Warehouse

    Rounds, Stewart A.; Buccola, Norman L.

    2015-01-01

    Water-quality models allow water resource professionals to examine conditions under an almost unlimited variety of potential future scenarios. The two-dimensional (longitudinal, vertical) water-quality model CE-QUAL-W2, version 3.7, was enhanced and augmented with new features to help dam operators and managers explore and optimize potential solutions for temperature management downstream of thermally stratified reservoirs. Such temperature management often is accomplished by blending releases from multiple dam outlets that access water of different temperatures at different depths. The modified blending algorithm in version 3.7 of CE-QUAL-W2 allows the user to specify a time-series of target release temperatures, designate from 2 to 10 floating or fixed-elevation outlets for blending, impose minimum and maximum head and flow constraints for any blended outlet, and set priority designations for each outlet that allow the model to choose which outlets to use and how to balance releases among them. The modified model was tested with a variety of examples and against a previously calibrated model of Detroit Lake on the North Santiam River in northwestern Oregon, and the results compared well. These updates to the blending algorithms will allow more complicated dam-operation scenarios to be evaluated somewhat automatically with the model, with decreased need for multiple model runs or preprocessing of model inputs to fully characterize the operational constraints.

  8. Preparation and release characteristics of polymer-coated and blended alginate microspheres.

    PubMed

    Lee, D W; Hwang, S J; Park, J B; Park, H J

    2003-01-01

    To prevent a rapid drug release from alginate microspheres in simulated intestinal media, alginate microspheres were coated or blended with polymers. Three polymers were selected and evaluated such as HPMC, Eudragit RS 30D and chitosan, as both coating materials and additive polymers for controlling the drug release. This study focused on the release characteristics of polymer-coated and blended alginate microspheres, varying the type of polymer and its concentration. The alginate microspheres were prepared by dropping the mixture of drug and sodium alginate into CaCl(2) solution using a spray-gun. Polymer-coated microspheres were prepared by adding alginate microspheres into polymer solution with mild stirring. Polymer-blended microspheres were prepared by dropping the mixture of drug, sodium alginate and additive polymer with plasticizer into CaCl(2) solution. In vitro release test was carried out to investigate the release profiles in 500 ml of phosphate buffered saline (PBS, pH 7.4). As the amount of polymer in sodium alginate or coating solution increase, the drug release generally decreased. HPMC-blended microspheres swelled but withstood the disintegration, showing an ideal linear release profiles. Chitosan-coated microspheres showed smooth and round surface and extended the release of drug. In comparison with chitosan-coated microspheres, HPMC-blended alginate microspheres can be easily made and used for controlled drug delivery systems due to convenient process and controlled drug release.

  9. Effects of Burning Alternative Fuel in a 5-Cup Combustor Sector

    NASA Technical Reports Server (NTRS)

    Tacina, K. M.; Chang, C. T.; Lee, C.-M.; He, Z.; Herbon, J.

    2015-01-01

    A goal of NASA's Environmentally Responsible Aviation (ERA) program is to develop a combustor that will reduce the NOx emissions and that can burn both standard and alternative fuels. To meet this goal, NASA partnered with General Electric Aviation to develop a 5-cup combustor sector; this sector was tested in NASA Glenn's Advanced Subsonic Combustion Rig (ASCR). To verify that the combustor sector was fuel-flexible, it was tested with a 50-50 blend of JP-8 and a biofuel made from the camelina sativa plant. Results from this test were compared to results from tests where the fuel was neat JP-8. Testing was done at three combustor inlet conditions: cruise, 30% power, and 7% power. When compared to burning JP-8, burning the 50-50 blend did not significantly affect emissions of NOx, CO, or total hydrocarbons. Furthermore, it did not significantly affect the magnitude and frequency of the dynamic pressure fluctuations.

  10. Evaluation of fuel additives for reduction of material imcompatibilities in methanol-gasoline blends

    NASA Technical Reports Server (NTRS)

    Rodriguez, C. F.; Barbee, J. G.; Knutson, W. K.; Cuellar, J. P., Jr.

    1983-01-01

    Screening tests determined the efficacy of six commercially available additives as modifiers of methanol's corrosivity toward metals and its weakening of tensile properties of nonmetals in automotive fuel systems. From the screening phase, three additives which seemed to protect some of the metals were tested in higher concentrations and binary combinations in search of optimal application conditions. Results indicate that two of the additives have protective properties and combining them increases the protection of the metals corroded by methanol-gasoline blends. Half of the metals in the tests were not corroded. Testing at recommended concentrations and then at higher concentrations and in combinations shows that the additives would have no protective or harmful effects on the nonmetals. Two additives emerged as candidates for application to the protection of metals in automotive methanol-gasoline fuel systems. The additives tested were assigned letter codes to protect their proprietary nature.

  11. Thermodynamics of reformulated automotive fuels

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zudkevitch, D.; Murthy, A.K.S.; Gmehling, J.

    1995-06-01

    Two methods for predicting Reid vapor pressure (Rvp) and initial vapor emissions of reformulated gasoline blends that contain one or more oxygenated compounds show excellent agreement with experimental data. In the first method, method A, D-86 distillation data for gasoline blends are used for predicting Rvp from a simulation of the mini dry vapor pressure equivalent (Dvpe) experiment. The other method, method B, relies on analytical information (PIANO analyses) of the base gasoline and uses classical thermodynamics for simulating the same Rvp equivalent (Rvpe) mini experiment. Method B also predicts composition and other properties for the fuel`s initial vapor emission.more » Method B, although complex, is more useful in that is can predict properties of blends without a D-86 distillation. An important aspect of method B is its capability to predict composition of initial vapor emissions from gasoline blends. Thus, it offers a powerful tool to planners of gasoline blending. Method B uses theoretically sound formulas, rigorous thermodynamic routines and uses data and correlations of physical properties that are in the public domain. Results indicate that predictions made with both methods agree very well with experimental values of Dvpe. Computer simulation methods were programmed and tested.« less

  12. Emission comparison of urban bus engine fueled with diesel oil and 'biodiesel' blend.

    PubMed

    Turrio-Baldassarri, Luigi; Battistelli, Chiara L; Conti, Luigi; Crebelli, Riccardo; De Berardis, Barbara; Iamiceli, Anna Laura; Gambino, Michele; Iannaccone, Sabato

    2004-07-05

    The chemical and toxicological characteristics of emissions from an urban bus engine fueled with diesel and biodiesel blend were studied. Exhaust gases were produced by a turbocharged EURO 2 heavy-duty diesel engine, operating in steady-state conditions on the European test 13 mode cycle (ECE R49). Regulated and unregulated pollutants, such as carcinogenic polycyclic aromatic hydrocarbons (PAHs) and nitrated derivatives (nitro-PAHs), carbonyl compounds and light aromatic hydrocarbons were quantified. Mutagenicity of the emissions was evaluated by the Salmonella typhimurium/mammalian microsome assay. The effect of the fuels under study on the size distribution of particulate matter (PM) was also evaluated. The use of biodiesel blend seems to result in small reductions of emissions of most of the aromatic and polyaromatic compounds; these differences, however, have no statistical significance at 95% confidence level. Formaldehyde, on the other hand, has a statistically significant increase of 18% with biodiesel blend. In vitro toxicological assays show an overall similar mutagenic potency and genotoxic profile for diesel and biodiesel blend emissions. The electron microscopy analysis indicates that PM for both fuels has the same chemical composition, morphology, shape and granulometric spectrum, with most of the particles in the range 0.06-0.3 microm.

  13. Investigation into the use of microwave sensors to monitor particulate manufacturing processes

    NASA Astrophysics Data System (ADS)

    Austin, John Samuel, III

    Knowledge of a material's properties in-line during manufacture is of critical importance to many industries, including the pharmaceutical industry, and can be used for either process or quality control. Different microwave sensor configurations were tested to determine both the moisture content and the bulk density in pharmaceutical powders during processing on-line. Although these parameters can significantly affect a material's flowability, compressibility, and cohesivity, in the presence of blends, the picture is incomplete. Due to the ease with which particulate blends tend to segregate, blend uniformity and chemical composition are two critical parameters in nearly all solids manufacturing industries. The prevailing wisdom has been that microwave sensors are not capable of or sensitive enough to measure the relative concentrations of components in a blend. Consequently, it is common to turn to near infrared sensing to determine material composition on-line. In this study, a novel microwave sensor was designed and utilized to determine, separately, the concentrations of different components in a blend of pharmaceutical powders. This custom microwave sensor was shown to have comparable accuracy to the state-of-the-art for both chemical composition and moisture content determination.

  14. Process improvement for regulatory analyses of custom-blend fertilizers.

    PubMed

    Wegner, Keith A

    2014-01-01

    Chemical testing of custom-blend fertilizers is essential to ensure that the products meet the formulation requirements. For purposes of proper crop nutrition and consumer protection, regulatory oversight promotes compliance and particular attention to blending and formulation specifications. Analyses of custom-blend fertilizer products must be performed and reported within a very narrow window in order to be effective. The Colorado Department of Agriculture's Biochemistry Laboratory is an ISO 17025 accredited facility and conducts analyses of custom-blend fertilizer products primarily during the spring planting season. Using the Lean Six Sigma (LSS) process, the Biochemistry Laboratory has reduced turnaround times from as much as 45 days to as little as 3 days. The LSS methodology focuses on waste reduction through identifying: non-value-added steps, unneeded process reviews, optimization of screening and confirmatory analyses, equipment utilization, nonessential reporting requirements, and inefficient personnel deployment. Eliminating these non-value-added activities helped the laboratory significantly shorten turnaround time and reduce costs. Key improvement elements discovered during the LSS process included: focused sample tracking, equipment redundancy, strategic supply stocking, batch size optimization, critical sample paths, elimination of nonessential QC reviews, and more efficient personnel deployment.

  15. Inquiry and Blended Learning Based Learning Material Development for Improving Student Achievement on General Physics I of Mathematics and Natural Science of State University of Medan

    ERIC Educational Resources Information Center

    Motlan; Sinulinggga, Karya; Siagian, Henok

    2016-01-01

    The aim of this research is to determine if inquiry and blended learning based materials can improve student's achievement. The learning materials are: book, worksheet, and test, website, etc. The type of this research is quasi experiment using two-group pretest posttest design. The population is all students of first year who take general physics…

  16. Characterization of mutagenic activity in grain-based coffee-substitute blends and instant coffees

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Johansson, M.A.E.; Knize, M.G.; Felton, J.S.

    1994-06-01

    Several grain-based coffee-substitute blends and instant coffees showed a mutagenic response in the Ames/Salmonella test using TA98, YG1024 and YG1O29 with metabolic activation. The beverage powders contained 150 to 500 TA98 and 1150 to 4050 YG1024 revertant colonies/gram, respectively. The mutagenic activity in the beverage powders was shown to be stable to heat and the products varied in resistance to acid nitrite treatment. Characterization of the mutagenic activity, using HPLC-and the Ames test of the collected fractions, showed the coffee-substitutes and instant coffees contain several mutagenic compounds, which are most likely aromatic amines.

  17. Anti-inflammatory properties of blended edible oil with synergistic antioxidants.

    PubMed

    Upadya, Haridas; Devaraju, C J; Joshi, Shashank R

    2015-01-01

    Blending of oil combines the potency of two edible oils and offers a balance of fatty acids. Various cooking preparations existing across different ethnicities and regions subject oil to different cooking temperatures thereby causing deterioration of the oil due to oxidative stress. In order to prevent the oxidative damage of unsaturated fatty acid, a blend of rice bran oil (RBO) and safflower oil (SO) (70:30) with an antioxidant technology was designed. A controlled trial was carried out to assess the efficacy of the blend on different biomarkers including lipid parameters and some important inflammatory markers that have the potency to lead to various lifestyle diseases. A prospective, double-blind, randomized, parallel group study (on 80 adult hyperlipidemic patients) was conducted for 3 months. During the study, all the subjects were recommended lifestyle modifications, which included, exercise regime and diet counseling; oil quantity consumed was 1 L/person/month for both the groups. The subjects were divided into two groups; one group, continued with their regularly consumed oil whereas, the other was given the test oil. Biomarkers assessed were lipid profile and seven other inflammatory markers were assessed. Low-density lipoprotein cholesterol (LDL-C) the primary marker for cardiovascular diseases showed a decrease of 56.07 ± 04.31 mg/dL and 31.98 ± 03.81 mg/dL (P < 0.001 by analysis of variance [ANOVA]) from baseline in test and control group, respectively, during 3 months. Similar reduction trends were observed for total cholesterol where -52.31 ± 13.04 mg/dL and 31.98 ± 04.12 mg/dL (P < 0.001 by ANOVA, between the groups) were seen in test and control group, respectively. Oxidized LDL and high sensitivity C-reactive protein showed a reduction of 2.23 ± 1.3 units/dL and 0.87 ± 2.85 mg/L in test group whereas; an increase of 1.04 ± 1.73 units/dL and 0.44 ± 2.37 mg/L was seen in the control group, respectively (P < 0.05 by Student's t-test, between the groups). The study showed that the blend of RBO and SO with antioxidant technology along with other lifestyle changes helps lowering of blood lipids and stated inflammatory biomarkers and thus, in turn may help prevent lifestyle diseases.

  18. Anti-inflammatory properties of blended edible oil with synergistic antioxidants

    PubMed Central

    Upadya, Haridas; Devaraju, C. J.; Joshi, Shashank R.

    2015-01-01

    Background: Blending of oil combines the potency of two edible oils and offers a balance of fatty acids. Various cooking preparations existing across different ethnicities and regions subject oil to different cooking temperatures thereby causing deterioration of the oil due to oxidative stress. In order to prevent the oxidative damage of unsaturated fatty acid, a blend of rice bran oil (RBO) and safflower oil (SO) (70:30) with an antioxidant technology was designed. A controlled trial was carried out to assess the efficacy of the blend on different biomarkers including lipid parameters and some important inflammatory markers that have the potency to lead to various lifestyle diseases. Study Design: A prospective, double-blind, randomized, parallel group study (on 80 adult hyperlipidemic patients) was conducted for 3 months. During the study, all the subjects were recommended lifestyle modifications, which included, exercise regime and diet counseling; oil quantity consumed was 1 L/person/month for both the groups. The subjects were divided into two groups; one group, continued with their regularly consumed oil whereas, the other was given the test oil. Biomarkers assessed were lipid profile and seven other inflammatory markers were assessed. Results: Low-density lipoprotein cholesterol (LDL-C) the primary marker for cardiovascular diseases showed a decrease of 56.07 ± 04.31 mg/dL and 31.98 ± 03.81 mg/dL (P < 0.001 by analysis of variance [ANOVA]) from baseline in test and control group, respectively, during 3 months. Similar reduction trends were observed for total cholesterol where −52.31 ± 13.04 mg/dL and 31.98 ± 04.12 mg/dL (P < 0.001 by ANOVA, between the groups) were seen in test and control group, respectively. Oxidized LDL and high sensitivity C-reactive protein showed a reduction of 2.23 ± 1.3 units/dL and 0.87 ± 2.85 mg/L in test group whereas; an increase of 1.04 ± 1.73 units/dL and 0.44 ± 2.37 mg/L was seen in the control group, respectively (P < 0.05 by Student's t-test, between the groups). Conclusion: The study showed that the blend of RBO and SO with antioxidant technology along with other lifestyle changes helps lowering of blood lipids and stated inflammatory biomarkers and thus, in turn may help prevent lifestyle diseases. PMID:26180768

  19. Cell culture medium improvement by rigorous shuffling of components using media blending.

    PubMed

    Jordan, Martin; Voisard, Damien; Berthoud, Antoine; Tercier, Laetitia; Kleuser, Beate; Baer, Gianni; Broly, Hervé

    2013-01-01

    A novel high-throughput methodology for the simultaneous optimization of many cell culture media components is presented. The method is based on the media blending approach which has several advantages as it works with ready-to-use media. In particular it allows precise pH and osmolarity adjustments and eliminates the need of concentrated stock solutions, a frequent source of serious solubility issues. In addition, media blending easily generates a large number of new compositions providing a remarkable screening tool. However, media blending designs usually do not provide information on distinct factors or components that are causing the desired improvements. This paper addresses this last point by considering the concentration of individual medium components to fix the experimental design and for the interpretation of the results. The extended blending strategy was used to reshuffle the 20 amino acids in one round of experiments. A small set of 10 media was specifically designed to generate a large number of mixtures. 192 mixtures were then prepared by media blending and tested on a recombinant CHO cell line expressing a monoclonal antibody. A wide range of performances (titers and viable cell density) was achieved from the different mixtures with top titers significantly above our previous results seen with this cell line. In addition, information about major effects of key amino acids on cell densities and titers could be extracted from the experimental results. This demonstrates that the extended blending approach is a powerful experimental tool which allows systematic and simultaneous reshuffling of multiple medium components.

  20. Effect of organo clay on curing, mechanical and dielectric properties of NR/SBR blends

    NASA Astrophysics Data System (ADS)

    Ravikumar, K.; Joseph, Reji; Ravichandran, K.

    2018-04-01

    Natural rubber (NR) and styrene butadiene rubber (SBR) based elastomeric blends reinforced with organically modified Sodium bentonite clay were prepared by two roll mills. Vulcanization parameters such as minimum and maximum torque values scorch and cure times are measured by Oscillating Disc Rheometer. Mechanical properties such as Tensile strength, modulus at 100%, 200% and 300% elongation and elongation at break and Hardness were measured by Universal testing machine and Durometer Shore A hardness meter respectively. Dielectric properties such as dielectric constant (ε’), dissipation factor (tanδ) and volume resistivity (ρv) were measured at room temperature. The curing studies show that torque values are increasing in NR/SBR blends by increase NR content. The scorch and optimum cure time in NR/SBR blends reinforced organo modified clay was found through increase in the SBR content. This may be due to better processing safety of the NR/SBR blends reinforced with organo modified clay. Mechanical properties show that addition of SBR in blends, tensile strength, elongation modulus increases, but 100% modulus slightly increases and no change was observed in Hardness. Dielectric studies show that dielectric constant of NR and SBR rubbers are almost same, it may due to their non-polar nature. But addition of SBR in NR/SBR blend, dielectric constant gradually increases and maximum value observed at 50/50 ratio. But no considerable change was observed in dissipation factor. Frequency dependant resistivity shows that volume resistivity was not changed with respect to frequency up to 3.5 kHz and beyond that the frequency dependence resistivity was found.

  1. A Study on the Reuse of Plastic Concrete Using Extended Set-Retarding Admixtures.

    PubMed

    Lobo, Colin; Guthrie, William F; Kacker, Raghu

    1995-01-01

    The disposal of ready mixed concrete truck wash water and returned plastic concrete is a growing concern for the ready mixed concrete industry. Recently, extended set-retarding admixtures, or stabilizers, which slow or stop the hydration of portland cement have been introduced to the market. Treating truck wash-water or returned plastic concrete with stabilizing admixtures delays its setting and hardening, thereby facilitating the incorporation of these typically wasted materials in subsequent concrete batches. In a statistically designed experiment, the properties of blended concrete containing stabilized plastic concrete were evaluated. The variables in the study included (1) concrete age when stabilized, (2) stabilizer dosage, (3) holding period of the treated (stabilized) concrete prior to blending with fresh ingredients, and (4) amount of treated concrete in the blended batch. The setting time, strength, and drying shrinkage of the blended concretes were evaluated. For the conditions tested, batching 5 % treated concrete with fresh material did not have a significant effect on the setting time, strength, or drying shrinkage of the resulting blended concrete. Batching 50 % treated concrete with fresh materials had a significant effect on the setting characteristics of the blended cocnrete, which in turn affected the water demand to maintain slump. The data suggests that for a known set of conditions, the stabilizer dosage can be optimized within a relatively narrow range to produce desired setting characteristics. The strength and drying shrinkage of the blended concretes were essentially a function of the water content at different sampling ages and the relationship followed the general trend of control concrete.

  2. A Study on the Reuse of Plastic Concrete Using Extended Set-Retarding Admixtures

    PubMed Central

    Lobo, Colin; Guthrie, William F.; Kacker, Raghu

    1995-01-01

    The disposal of ready mixed concrete truck wash water and returned plastic concrete is a growing concern for the ready mixed concrete industry. Recently, extended set-retarding admixtures, or stabilizers, which slow or stop the hydration of portland cement have been introduced to the market. Treating truck wash-water or returned plastic concrete with stabilizing admixtures delays its setting and hardening, thereby facilitating the incorporation of these typically wasted materials in subsequent concrete batches. In a statistically designed experiment, the properties of blended concrete containing stabilized plastic concrete were evaluated. The variables in the study included (1) concrete age when stabilized, (2) stabilizer dosage, (3) holding period of the treated (stabilized) concrete prior to blending with fresh ingredients, and (4) amount of treated concrete in the blended batch. The setting time, strength, and drying shrinkage of the blended concretes were evaluated. For the conditions tested, batching 5 % treated concrete with fresh material did not have a significant effect on the setting time, strength, or drying shrinkage of the resulting blended concrete. Batching 50 % treated concrete with fresh materials had a significant effect on the setting characteristics of the blended cocnrete, which in turn affected the water demand to maintain slump. The data suggests that for a known set of conditions, the stabilizer dosage can be optimized within a relatively narrow range to produce desired setting characteristics. The strength and drying shrinkage of the blended concretes were essentially a function of the water content at different sampling ages and the relationship followed the general trend of control concrete. PMID:29151762

  3. Abnormalities in the male reproductive system after exposure to diesel and biodiesel blend.

    PubMed

    Kisin, Elena R; Yanamala, Naveena; Farcas, Mariana T; Gutkin, Dmitriy W; Shurin, Michael R; Kagan, Valerian E; Bugarski, Aleksandar D; Shvedova, Anna A

    2015-03-01

    Altering the fuel source from petroleum-based ultralow sulfur diesel to biodiesel and its blends is considered by many to be a sustainable choice for controlling exposures to particulate material. As the exhaust of biodiesel/diesel blends is composed of a combination of combustion products of polycyclic aromatic hydrocarbons and fatty acid methyl esters, we hypothesize that 50% biodiesel/diesel blend (BD50) exposure could induce harmful outcomes because of its ability to trigger oxidative damage. Here, adverse effects were compared in murine male reproductive organs after pharyngeal aspiration with particles generated by engine fueled with BD50 or neat petroleum diesel (D100). When compared with D100, exposure to BD50 significantly altered sperm integrity, including concentration, motility, and morphological abnormalities, as well as increasing testosterone levels in testes during the time course postexposure. Serum level of luteinizing hormone was significantly depleted only after BD50 exposure. Moreover, we observed that exposure to BD50 significantly increased sperm DNA fragmentation and the upregulation of inflammatory cytokines in the serum and testes on Day 7 postexposure when compared with D100. Histological evaluation of testes sections from BD50 exposure indicated more noticeable interstitial edema, degenerating spermatocytes, and dystrophic seminiferous tubules with arrested spermatogenesis. Significant differences in the level of oxidative stress assessed by accumulation of lipid peroxidation products and depletion of glutathione were detected on exposure to respirable BD50 and D100. Taken together, these results indicate that exposure of mice to inhalable BD50 caused more pronounced adverse effects on male reproductive function than diesel. © 2014 Wiley Periodicals, Inc.

  4. Abnormalities in the Male Reproductive System After Exposure to Diesel and Biodiesel Blend

    PubMed Central

    Kisin, Elena R.; Yanamala, Naveena; Farcas, Mariana T.; Gutkin, Dmitriy W.; Shurin, Michael R.; Kagan, Valerian E.; Bugarski, Aleksandar D.; Shvedova, Anna A.

    2016-01-01

    Altering the fuel source from petroleum-based ultra-low sulfur diesel to biodiesel and its blends is considered by many to be a sustainable choice for controlling exposures to particulate material. As the exhaust of biodiesel/diesel blends is composed of a combination of combustion products of polycyclic aromatic hydrocarbons and fatty acid methyl esters, we hypothesize that 50% biodiesel/diesel blend (BD50) exposure could induce harmful outcomes because of its ability to trigger oxidative damage. Here, adverse effects were compared in murine male reproductive organs after pharyngeal aspiration with particles generated by engine fueled with BD50 or neat petroleum diesel (D100). When compared with D100, exposure to BD50 significantly altered sperm integrity, including concentration, motility, and morphological abnormalities, as well as increasing testosterone levels in testes during the time course postexposure. Serum level of luteinizing hormone was significantly depleted only after BD50 exposure. Moreover, we observed that exposure to BD50 significantly increased sperm DNA fragmentation and the upregulation of inflammatory cytokines in the serum and testes on Day 7 postexposure when compared with D100. Histological evaluation of testes sections from BD50 exposure indicated more noticeable interstitial edema, degenerating spermatocytes, and dystrophic seminiferous tubules with arrested spermatogenesis. Significant differences in the level of oxidative stress assessed by accumulation of lipid peroxidation products and depletion of glutathione were detected on exposure to respirable BD50 and D100. Taken together, these results indicate that exposure of mice to inhalable BD50 caused more pronounced adverse effects on male reproductive function than diesel. PMID:25327512

  5. Comparative Studies on Performance Characteristics of CI Engine Fuelled with Neem Methyl Ester and Mahua Methyl Ester and Its Respective Blends with Diesel Fuel.

    PubMed

    Ragit, S S; Mohapatra, S K; Kundu, K

    2014-01-01

    In the present investigation, neem and mahua methyl ester were prepared by transesterification using potassium hydroxide as a catalyst and tested in 4-stroke single cylinder water cooled diesel engine. Tests were carried out at constant speed of 1500 rev/min at different brake mean effective pressures. A series of tests were conducted which worked at different brake mean effective pressures, OkPa, 1kPa, 2kPa, 3kPa, 4kPa, 5kPa, 6kPa and 6.5kPa. The performance and exhaust emission characteristics of the diesel engine were analyzed and compared with diesel fuel. Results showed that BTE of NME was comparable with diesel and it was noted that the BTE of N0100 is 63.11% higher than that of diesel at part load whereas it reduces 11.2% with diesel fuel at full load. In case of full load, NME showed decreasing trend with diesel fuel. BTE of diesel was 15.37% and 36.89% at part load and full load respectively. The observation indicated that BTE for MME 100 was slightly higher than diesel at part loads. The specific fuel consumption (SFC) was more for almost all blends at all loads, compared to diesel. At part load, the EGT of MME and its blends were showing similar trend to diesel fuel and at full load, the exhaust gas temperature of MME and blends were higher than diesel. Based on this study, NME could be a substitute for diesel fuel in diesel engine.

  6. An efficient, maintenance free and approved method for spectroscopic control and monitoring of blend uniformity: The moving F-test.

    PubMed

    Besseling, Rut; Damen, Michiel; Tran, Thanh; Nguyen, Thanh; van den Dries, Kaspar; Oostra, Wim; Gerich, Ad

    2015-10-10

    Dry powder mixing is a wide spread Unit Operation in the Pharmaceutical industry. With the advent of in-line Near Infrared (NIR) Spectroscopy and Quality by Design principles, application of Process Analytical Technology to monitor Blend Uniformity (BU) is taking a more prominent role. Yet routine use of NIR for monitoring, let alone control of blending processes is not common in the industry, despite the improved process understanding and (cost) efficiency that it may offer. Method maintenance, robustness and translation to regulatory requirements have been important barriers to implement the method. This paper presents a qualitative NIR-BU method offering a convenient and compliant approach to apply BU control for routine operation and process understanding, without extensive calibration and method maintenance requirements. The method employs a moving F-test to detect the steady state of measured spectral variances and the endpoint of mixing. The fundamentals and performance characteristics of the method are first presented, followed by a description of the link to regulatory BU criteria, the method sensitivity and practical considerations. Applications in upscaling, tech transfer and commercial production are described, along with evaluation of the method performance by comparison with results from quantitative calibration models. A full application, in which end-point detection via the F-test controls the blending process of a low dose product, was successfully filed in Europe and Australia, implemented in commercial production and routinely used for about five years and more than 100 batches. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Design features to enhance external hip protector adherence in the nursing home setting.

    PubMed

    Honkanen, Lisa A; Dehner, Melissa L; Lachs, Mark S

    2006-11-01

    To determine the preferences for external hip protector (EHP) design features of both certified nursing assistants (CNAs) and nursing home laundry personnel, and to test the durability of favored model features. Cross-sectional descriptive study of CNAs' and laundry personnels' preferences and a prospective experimental study of EHP fastener durability under institutional laundry conditions. Three urban nursing homes and a hospital-based laundry service. Twenty-seven CNAs, 4 laundry service supervisors. Five focus groups with CNAs and a survey of laundry supervisors were conducted to elicit preferences of EHP design features with an emphasis on convenience and durability. A laundry test of 20 EHPs was conducted to compare these design features. There was wide agreement among CNAs and laundry personnel that EHPs with soft pads in garments of light neutral colors, and cotton-blend fabrics were most preferred. CNAs preferred sewn-in pads to removeable ones, but laundry personnel had no consensus on this issue. For dependent residents, wraparound (front opening) garments using Velcro were preferred by CNAs, whereas laundry supervisors preferred snap closures. When EHP underwent repeated washing in the laundry test, Velcro and snaps were functionally comparable at 52 cycles. Garments constructed of heavyweight cotton blends, polyester, or cotton with spandex maintained elasticity at 52 weeks, whereas the lightweight cotton blend stretched significantly. Based on CNAs' preferences, laundry personnels' input, and a laundry test, EHP design features that could enhance both caregiver efficiency and resident comfort include soft pads sewn into a light-colored (but non-white) heavier weight cotton-blend garment, with the availability of both a pull-up style and a wraparound style using Velcro fasteners. Snaps did not demonstrate superior durability in the laundry test, but further comparison with Velcro under clinical conditions is indicated. Education and inclusion of CNAs in EHP decision making are important ways to improve EHP adherence.

  8. Improving Anatomic Pathology in Sub-Saharan Africa to Support Cancer Care.

    PubMed

    Wilson, Michael L; Ayers, Stephanie; Berney, Daniel; Eslan, Alexia; Guarner, Jeannette; Lester, Susan; Masia, Ricard; Moloo, Zahir; Mutuku, Angela; Roberts, Drucilla; Stall, Jennifer; Sayed, Shahin

    2018-03-07

    Cancer care requires both accurate pathologic diagnosis as well as pathologic cancer staging. We evaluated three approaches to training pathologists in sub-Saharan Africa to perform pathologic cancer staging of breast, cervix, prostate, and colorectal cancers. One of three training methods was used at each workshop: didactic, case-based testing (CBT), or a blended approach. The project involved 52 participants from 16 pathology departments in 11 countries in East, Central, and Southern Africa. Evaluation of each method included pre- and postworkshop knowledge assessments, online pre- and postworkshop surveys of practice changes at the individual and institutional levels, and selected site visits. While CBT resulted in the highest overall average postassessment individual scores, both CBT and blended approaches resulted in 19% increases in average scores from pre- to postworkshop assessments. Institutions that participated in the blended workshop had increased changes in practice as indicated by the institutional survey. Both CBT and a blended approach are effective methods for training pathologists in pathologic cancer staging. Both are superior to traditional lectures alone.

  9. Plasticized poly(lactic acid)-poly(hydroxybutyrate) (PLA-PHB) blends incorporated with catechin intended for active food-packaging applications.

    PubMed

    Arrieta, Marina Patricia; Castro-López, María del Mar; Rayón, Emilio; Barral-Losada, Luis Fernando; López-Vilariño, José Manuel; López, Juan; González-Rodríguez, María Victoria

    2014-10-15

    Active biobased packaging materials based on poly(lactic acid)-poly(hydroxybutyrate) (PLA-PHB) blends were prepared by melt blending and fully characterized. Catechin incorporation, as antioxidant compound, enhanced the thermal stability, whereas its release was improved by the addition of acetyl(tributyl citrate) (ATBC) as plasticizer. Whereas the incorporation of ATBC resulted in a reduction of elastic modulus and hardness, catechin addition produced more rigid materials due to hydrogen-bonding interactions between catechin hydroxyl groups and carbonyl groups of PLA and PHB. The quantification of catechin released into a fatty food simulant and the antioxidant effectiveness after the release process were demonstrated. The effect of the materials' exposure to a food simulant was also investigated. PHB-added materials maintained their structural and mechanical properties after 10 days in a test medium that represents the worst foreseeable conditions of the intended use. Thus, plasticized PLA-PHB blends with catechin show their potential as biobased active packaging for fatty food.

  10. Long term exposure of metals to hydrazine nitrate blend

    NASA Technical Reports Server (NTRS)

    Moran, Clifford M.; Blue, Gary D.

    1986-01-01

    A long term testing program is being conducted to determine the effects of materials in contact with a hydrazine nitrate blend for the purpose of designing chemical propulsion systems which can be used for current as well as future planetary spacecraft. Analysis of this data indicates that some aluminum alloys are acceptable for use with the particular blend of fuel used. Titanium alloy was identified as being acceptable for 10-year applications. Corrosion resistant steels, however, were found to have excessive corrosion rates and are therefore considered unacceptable for long-term use. There is also some evidence that the propellant decomposed at a rate far in excess of the acceptable rate of 0.1 percent per year when in contact with stainless steel.

  11. Performance Test on Compression Ignition Engine by Blending Ethanol and Waste Plastic Pyrolysis Oil with Cetane Additive

    NASA Astrophysics Data System (ADS)

    Padmanabhan, S.; Ganesan, S.; Jeswin Arputhabalan, J.; Chithrala, Varun; Ganesh Bairavan, P.

    2017-05-01

    The demand for diesel fuel is higher than that of petrol throughout the world hence seeking alternative to mineral diesel is a natural choice. Alternative fuels should be easily available at lower cost, environment friendly and fulfill energy needs without modifying engine’s operational parameters. Waste to energy is the trend in the selection of alternate fuels. In this work, Waste Plastic Pyrolysis oil (WPPO), Ethanol, Diesel blend with Cetane additive has been attempted as an alternative fuel. A Twin cylinder, Direct Injection engine was used to assess the engine performance and emission characteristics of waste plastic pyrolysis oil with cetane additive. Experimental results of blended plastic fuel and diesel fuel were compared.

  12. Online learning versus blended learning of clinical supervisee skills with pre-registration nursing students: A randomised controlled trial.

    PubMed

    McCutcheon, Karen; O'Halloran, Peter; Lohan, Maria

    2018-06-01

    The World Health Organisation amongst others recognises the need for the introduction of clinical supervision education in health professional education as a central strategy for improving patient safety and patient care. Online and blended learning methods are growing exponentially in use in higher education and the systematic evaluation of these methods will aid understanding of how best to teach clinical supervision. The purpose of this study was to test whether undergraduate nursing students who received clinical supervisee skills training via a blended learning approach would score higher in terms of motivation and attitudes towards clinical supervision, knowledge of clinical supervision and satisfaction of learning method, when compared to those students who received an online only teaching approach. A post-test-only randomised controlled trial. Participants were a total of 122 pre-registration nurses enrolled at one United Kingdom university, randomly assigned to the online learning control group (n = 60) or the blended learning intervention group (n = 62). The blended learning intervention group participated in a face-to-face tutorial and the online clinical supervisee skills training app. The online learning control group participated in an online discussion forum and the same online clinical supervisee skills training app. The outcome measures were motivation and attitudes using the modified Manchester Clinical Supervision Scale, knowledge using a 10 point Multiple Choice Questionnaire and satisfaction using a university training evaluation tool. Statistical analysis was performed using independent t-tests to compare the differences between the means of the control group and the intervention group. Thematic analysis was used to analyse responses to open-ended questions. All three of our study hypotheses were confirmed. Participants who received clinical supervisee skills training via a blended learning approach scored higher in terms of motivation and attitudes - mean (m) = 85.5, standard deviation (sd) = 9.78, number of participants (n) = 62 - compared to the online group (m = 79.5, sd = 9.69, n = 60) (p = .001). The blended learning group also scored higher in terms of knowledge (m = 4.2, sd = 1.43, n = 56) compared to the online group (m = 3.51, sd = 1.51, n = 57) (p = .015); and in terms of satisfaction (m = 30.89, sd = 6.54, n = 57) compared to the online group (m = 26.49, sd = 6.93, n = 55) (p = .001). Qualitative data supported results. Blended learning provides added pedagogical value when compared to online learning in terms of teaching undergraduate nurses clinical supervision skills. The evidence is timely given worldwide calls for expanding clinical skills supervision in undergraduate health professional education to improve quality of care and patient safety. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

  13. Tag Array gene chip rapid diagnosis anti-tuberculosis drug resistance in pulmonary tuberculosis -a feasibility study.

    PubMed

    Wu, Wenjie; Cheng, Peng; Lyu, Jingtong; Zhang, Zehua; Xu, Jianzhong

    2018-05-01

    We developed a Tag Array chip for detecting first- and second-line anti tuberculosis drug resistance in pulmonary tuberculosis and compared the analytical performance of the gene chip to that of phenotypic drug susceptibility testing (DST). From November 2011 to April 2016.234 consecutive culture-confirmed, clinically and imaging diagnosed patients with pulmonary tuberculosis from Southwest Hospital, Chongqing were enrolled into the study. Specimens collected during sputum or bronchoalveolar lavage fluid from the pulmonary tuberculosis patients were subjected to M. tuberculosis species identification and drug-resistance detection by the Tag Array gene chip, and evaluate the sensitivity and specificity of chip. A total of 186 patients was diagnosed drug-resistant tuberculosis. The detection of rifampicin (RFP), isoniazid (INH), fluoroquinolones (FQS), streptomycin (SM) resistance genes was highly sensitive and specific: however, for detection of amikacin (AMK), capreomycin (CPM), Kanamycin (KM), specificity was higher, but sensitivity was lower. Sensitivity for the detection of a mutation in the eis promoter region could be improved. The detection sensitivity of the EMB resistance gene was low, therefore it is easy to miss a diagnosis of EMB drug resistance, but its specificity was high. Tag Array chip can achieve rapid, accurate and high-throughput detection of tuberculosis resistance in pulmonary tuberculosis, which has important clinical significance and feasibility. Copyright © 2018. Published by Elsevier Ltd.

  14. Effect of Molarity of Sodium Hydroxide and Curing Method on the Compressive Strength of Ternary Blend Geopolymer Concrete

    NASA Astrophysics Data System (ADS)

    Sathish Kumar, V.; Ganesan, N.; Indira, P. V.

    2017-07-01

    Concrete plays a vital role in the development of infrastructure and buildings all over the world. Geopolymer based cement-less concrete is one of the current findings in the construction industry which leads to a green environment. This research paper deals with the results of the use of Fly ash (FA), Ground Granulated Blast Furnace Slag (GGBS) and Metakaolin (MK) as a ternary blend source material in Geopolymer concrete (GPC). The aspects that govern the compressive strength of GPC like the proportion of source material, Molarity of Sodium Hydroxide (NaOH) and Curing methods were investigated. The purpose of this research is to optimise the local waste material and use them effectively as a ternary blend in GPC. Seven combinations of binder were made in this study with replacement of FA with GGBS and MK by 35%, 30%, 25%, 20%, 15%, 10%, 5% and 5%, 10%, 15%, 20%, 25%, 30%, 35% respectively. The molarity of NaOH solution was varied by 12M, 14M and 16M and two types of curing method were adopted, viz. Hot air oven curing and closed steam curing for 24 hours at 60°C (140°F). The samples were kept at ambient temperature till testing. The compressive strength was obtained after 7 days and 28 days for the GPC cubes. The test data reveals that the ternary blend GPC with molarity 14M cured by hot air oven produces the maximum compressive strength. It was also observed that the compressive strength of the oven cured GPC is approximately 10% higher than the steam cured GPC using the ternary blend.

  15. Effects of supplementation with acai (Euterpe oleracea Mart.) berry-based juice blend on the blood antioxidant defence capacity and lipid profile in junior hurdlers. A pilot study.

    PubMed

    Sadowska-Krępa, E; Kłapcińska, B; Podgórski, T; Szade, B; Tyl, K; Hadzik, A

    2015-06-01

    The purpose of this pilot study was to examine whether regular consumption of an acai berry-based juice blend would affect sprint performance and improve blood antioxidant status and lipid profile in junior athletes. Seven junior hurdlers (17.5±1.2 years) taking part in a pre-season conditioning camp were supplemented once a day, for six weeks, with 100 ml of the juice blend. At the start and the end of the camp the athletes performed a 300-m sprint running test on an outdoor track. Blood samples were taken before and immediately after the test and after 1 h of recovery. Blood antioxidant status was evaluated based on activities of antioxidant enzymes (superoxide dismutase [SOD], catalase [CAT], glutathione peroxidase [GSH-Px], glutathione reductase [GR]), concentrations of non-enzymatic antioxidants (reduced glutathione [GSH], uric acid), total plasma polyphenols, ferric reducing ability of plasma (FRAP), thiobarbituric acid reactive substances (TBARS) and activities of creatine kinase (CK) and lactate dehydrogenase (LDH) as muscle damage markers. In order to evaluate potential health benefits of the acai berry, the post-treatment changes in lipid profile parameters (triglycerides, cholesterol and its fractions) were analysed. Six weeks' consumption of acai berry-based juice blend had no effect on sprint performance, but it led to a marked increase in the total antioxidant capacity of plasma, attenuation of the exercise-induced muscle damage, and a substantial improvement of serum lipid profile. These findings strongly support the view of the health benefits of supplementation with the acai berry-based juice blend, mainly attributed to its high total polyphenol content and the related high in vivo antioxidant and hypocholesterolaemic activities of this supplement.

  16. Effects of supplementation with acai (Euterpe oleracea Mart.) berry-based juice blend on the blood antioxidant defence capacity and lipid profile in junior hurdlers. A pilot study

    PubMed Central

    Kłapcińska, B; Podgórski, T; Szade, B; Tyl, K; Hadzik, A

    2015-01-01

    The purpose of this pilot study was to examine whether regular consumption of an acai berry-based juice blend would affect sprint performance and improve blood antioxidant status and lipid profile in junior athletes. Seven junior hurdlers (17.5±1.2 years) taking part in a pre-season conditioning camp were supplemented once a day, for six weeks, with 100 ml of the juice blend. At the start and the end of the camp the athletes performed a 300-m sprint running test on an outdoor track. Blood samples were taken before and immediately after the test and after 1 h of recovery. Blood antioxidant status was evaluated based on activities of antioxidant enzymes (superoxide dismutase [SOD], catalase [CAT], glutathione peroxidase [GSH-Px], glutathione reductase [GR]), concentrations of non-enzymatic antioxidants (reduced glutathione [GSH], uric acid), total plasma polyphenols, ferric reducing ability of plasma (FRAP), thiobarbituric acid reactive substances (TBARS) and activities of creatine kinase (CK) and lactate dehydrogenase (LDH) as muscle damage markers. In order to evaluate potential health benefits of the acai berry, the post-treatment changes in lipid profile parameters (triglycerides, cholesterol and its fractions) were analysed. Six weeks’ consumption of acai berry-based juice blend had no effect on sprint performance, but it led to a marked increase in the total antioxidant capacity of plasma, attenuation of the exercise-induced muscle damage, and a substantial improvement of serum lipid profile. These findings strongly support the view of the health benefits of supplementation with the acai berry-based juice blend, mainly attributed to its high total polyphenol content and the related high in vivo antioxidant and hypocholesterolaemic activities of this supplement. PMID:26060341

  17. Papain wound dressings obtained from poly(vinyl alcohol)/calcium alginate blends as new pharmaceutical dosage form: Preparation and preliminary evaluation.

    PubMed

    Dutra, J A P; Carvalho, S G; Zampirolli, A C D; Daltoé, R D; Teixeira, R M; Careta, F P; Cotrim, M A P; Oréfice, R L; Villanova, J C O

    2017-04-01

    Transparent, soft, flexible, mechanically resistant films, which are ideal for use as wound dressings were prepared in the presence of 2% papain, a proteolytic enzyme that can play a role in the chemical debridement of the skin and can accelerate the healing process. The films, based on poly(vinyl alcohol):calcium alginate blends with increasing concentrations of polysaccharide (10, 20, and 30% v/v), were obtained by casting method. FTIR and DSC analyses were performed to assess the composition and miscibility of blends. Mechanical properties such as tensile strength, elasticity modulus, and elongation at breakpoint were evaluated. The influence of different concentrations of calcium alginate on physical attributes of films like wettability, swelling capacity and mechanical properties was determined. The stability of papain in the films was assessed indirectly by hemolytic activity assay employing direct contact method and confirmed by technique based on blood agar diffusion. Preliminary cytotoxicity was evaluated with the XTT method. The results showed that at the polymer concentrations tested, the blends were miscible. The increase in the content of the calcium alginate increased the wettability and swelling capacity of the films, which is desirable in wound dressings. On the other hand, mechanical resistance decreased without causing breakage of the films during the swelling tests. The hemolytic activity of the films was maintained during the studied period, suggesting the stability of papain in the proposed formulations. Cellular viability indicated that the films were non-toxic. The analysis of the results showed that it is possible to prepare interactive and bioactive wound dressing containing papain from blends of PVA and calcium alginate polymers. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. A Navy User’s Guide for Quality Assurance of New Concrete Construction

    DTIC Science & Technology

    2012-06-01

    types and blends of cements, fly ash, silica fume, and blast furnace slag . During construction, concrete samples are taken to test and document the...chemical compositions provided by specific types and blends of cements, fly ash, silica fume, and blast furnace slag when used with specific aggregates...of portland cement and blast furnace slag . Before the 11 owner accepts the completed structure, all cracks transverse to the steel rebar in excess

  19. Conversion of a Micro, Glow-Ignition, Two-Stroke Engine from Nitromethane-Methanol Blend Fuel to Military Jet Propellant (JP-8)

    DTIC Science & Technology

    2012-01-01

    Table 10-4: Selected Birk polyimide heater sizes, resistances and locations [37] ........................ 79 Table 10-5: Final starting tests with (3...damage, and fire are prevalent. Kerosene type fuels are also cheaper and more common than nitromethane-methanol blend fuels. One final note is...diesel fuel was changed to produce lower emissions, the abrasiveness of diesel fuel increased. This was especially problematic for the new high

  20. Hydrogen effects on materials for CNG/H2 blends.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Farese, David; Keller, Jay O.; Somerday, Brian P.

    2010-09-01

    No concerns for Hydrogen-Enriched Compressed Natural gas (HCNG) in steel storage tanks if material strength is < 950 MPa. Recommend evaluating H{sub 2}-assisted fatigue cracking in higher strength steels at H{sub 2} partial pressure in blend. Limited fatigue testing on higher strength steel cylinders in H{sub 2} shows promising results. Impurities in Compressed Natural Gas (CNG) (e.g., CO) may provide extrinsic mechanism for mitigating H{sub 2}-assisted fatigue cracking in steel tanks.

  1. Impact of Fire Resistant Fuel Blends on Compression Ignition Engine Performance

    DTIC Science & Technology

    2011-07-01

    EFFECTS ON ENGINE PERFORMANCE FRF blends were tested in the CAT C7 and GEP 6.5L(T) engines to determine the effects of FRF on engine ...impact on efficiency of the Stanadyne rotary injection pump used in the GEP 6.5L(T) engine , thus largely effecting its power output when varying... exhaust backpressure .  Emissions are sampled from an exhaust probe installed between the engine and exhaust system butterfly valve. 

  2. Mosquito repellent activity of volatile oils from selected aromatic plants.

    PubMed

    Lalthazuali; Mathew, Nisha

    2017-02-01

    Essential oils from fresh leaves of four aromatic plants viz., Ocimum sanctum, Mentha piperita, Eucalyptus globulus and Plectranthus amboinicus were extracted by hydrodistillation. The test solutions were prepared as 20% essential oil in ethanol and positive control as 20% DEET in ethanol. Essential oil blend was prepared as 5% concentration. Nulliparous, 3-5-day-old female adult Aedes aegypti mosquitoes were used for repellency screening as per ICMR protocol. The study showed that the repellency of 20% essential oil of O. sanctum, M. piperita and P. amboinicus were comparable with that of the standard DEET (20%) as no mosquito landing on the test was observed up to 6 h. The E. globulus oil exhibited mosquito repellency only upto 1½ h. Considerable mosquito landing and feeding was displayed in negative control. In the case of the oil blend, no landing of mosquitoes was seen up to 6 h as that of positive control. The results showed that the essential oil blend from O. sanctum, M. piperita, E. globulus and P. amboinicus could repel Ae. aegypti mosquitoes or prevent from feeding as in the case of DEET even at a lower concentration of 5%. This study demonstrates the potential of essential oils from O. sanctum, M. piperita, E. globulus and P. amboinicus and their blend as mosquito repellents against Ae. aegypti, the vector of dengue, chikungunya and yellow fever.

  3. PM, carbon, and PAH emissions from a diesel generator fuelled with soy-biodiesel blends.

    PubMed

    Tsai, Jen-Hsiung; Chen, Shui-Jen; Huang, Kuo-Lin; Lin, Yuan-Chung; Lee, Wen-Jhy; Lin, Chih-Chung; Lin, Wen-Yinn

    2010-07-15

    Biodiesels have received increasing attention as alternative fuels for diesel engines and generators. This study investigates the emissions of particulate matter (PM), total carbon (TC), e.g., organic/elemental carbons, and polycyclic aromatic hydrocarbons (PAHs) from a diesel generator fuelled with soy-biodiesel blends. Among the tested diesel blends (B0, B10 (10 vol% soy-biodiesel), B20, and B50), B20 exhibited the lowest PM emission concentration despite the loads (except the 5 kW case), whereas B10 displayed lower PM emission factors when operating at 0 and 10 kW than the other fuel blends. The emission concentrations or factors of EC, OC, and TC were the lowest when B10 or B20 was used regardless of the loading. Under all tested loads, the average concentrations of total-PAHs emitted from the generator using the B10 and B20 were lower (by 38% and 28%, respectively) than those using pure petroleum diesel fuel (B0), while the emission factors of total-PAHs decreased with an increasing ratio of biodiesel to premium diesel. With an increasing loading, although the brake specific fuel consumption decreased, the energy efficiency increased despite the bio/petroleum diesel ratio. Therefore, soy-biodiesel is promising for use as an alternative fuel for diesel generators to increase energy efficiency and reduce the PM, carbon, and PAH emissions. 2010 Elsevier B.V. All rights reserved.

  4. Puffing of okara/rice blends using a rice cake machine.

    PubMed

    Xie, M; Huff, H; Hsieh, F; Mustapha, A

    2008-10-01

    Okara is the insoluble byproduct of soymilk and tofu manufactures. It is cheap, high in nutrients, and possesses great potential to be applied to functional human foods. In this study, a puffed okara/rice cake product was developed with blends of okara pellets and parboiled rice. Consumer preference and acceptance tests were conducted for the product. Okara pellets were prepared by grinding the strands obtained from extruding a mixture of dried okara and rice flour (3:2, w/w) with a twin-screw extruder. Okara pellets and parboiled rice were blended in 4 ratios, 90:10, 70:30, 40:60, and 0:100 (w/w), and tempered to 14% and 17% moisture. The blends were puffed at 221, 232, and 243 degrees C for 4, 5, or 6 s. The okara/rice cakes were evaluated for specific volume (SPV), texture, color, and percent weight loss after tumbling. Overall, the decrease in okara content and increase in moisture, heating temperature and time led to greater specific volume (SPV) and hardness, lighter color, and lower percent weight loss after tumbling. The consumer tests indicated that the okara/rice cake containing 70% okara pellets was preferred and the 90% one was liked the least. The possible drivers of liking for the puffed okara/rice cakes could be the okara content, hardness, SPV, bright color, and percent weight loss after tumbling.

  5. Repeated testing improves achievement in a blended learning approach for risk competence training of medical students: results of a randomized controlled trial.

    PubMed

    Spreckelsen, C; Juenger, J

    2017-09-26

    Adequate estimation and communication of risks is a critical competence of physicians. Due to an evident lack of these competences, effective training addressing risk competence during medical education is needed. Test-enhanced learning has been shown to produce marked effects on achievements. This study aimed to investigate the effect of repeated tests implemented on top of a blended learning program for risk competence. We introduced a blended-learning curriculum for risk estimation and risk communication based on a set of operationalized learning objectives, which was integrated into a mandatory course "Evidence-based Medicine" for third-year students. A randomized controlled trial addressed the effect of repeated testing on achievement as measured by the students' pre- and post-training score (nine multiple-choice items). Basic numeracy and statistical literacy were assessed at baseline. Analysis relied on descriptive statistics (histograms, box plots, scatter plots, and summary of descriptive measures), bootstrapped confidence intervals, analysis of covariance (ANCOVA), and effect sizes (Cohen's d, r) based on adjusted means and standard deviations. All of the 114 students enrolled in the course consented to take part in the study and were assigned to either the intervention or control group (both: n = 57) by balanced randomization. Five participants dropped out due to non-compliance (control: 4, intervention: 1). Both groups profited considerably from the program in general (Cohen's d for overall pre vs. post scores: 2.61). Repeated testing yielded an additional positive effect: while the covariate (baseline score) exhibits no relation to the post-intervention score, F(1, 106) = 2.88, p > .05, there was a significant effect of the intervention (repeated tests scenario) on learning achievement, F(1106) = 12.72, p < .05, d = .94, r = .42 (95% CI: [.26, .57]). However, in the subgroup of participants with a high initial numeracy score no similar effect could be observed. Dedicated training can improve relevant components of risk competence of medical students. An already promising overall effect of the blended learning approach can be improved significantly by implementing a test-enhanced learning design, namely repeated testing. As students with a high initial numeracy score did not profit equally from repeated testing, target-group specific opt-out may be offered.

  6. Improved Algorithms for Blending Dam Releases to Meet Downstream Water-Temperature Targets in the CE-QUAL-W2 Water-Quality Model

    NASA Astrophysics Data System (ADS)

    Rounds, S. A.; Buccola, N. L.

    2014-12-01

    The two-dimensional (longitudinal, vertical) water-quality model CE-QUAL-W2, version 3.7, was enhanced with new features to help dam operators and managers efficiently explore and optimize potential solutions for temperature management downstream of thermally stratified reservoirs. Such temperature management often is accomplished by blending releases from multiple dam outlets that access water of different temperatures at different depths in the reservoir. The original blending algorithm in this version of the model was limited to mixing releases from two outlets at a time, and few constraints could be imposed. The new enhanced blending algorithm allows the user to (1) specify a time-series of target release temperatures, (2) designate from 2 to 10 floating or fixed-elevation outlets for blending, (3) impose maximum head constraints as well as minimum and maximum flow constraints for any blended outlet, and (4) set a priority designation for each outlet that allows the model to choose which outlets to use and how to balance releases among them. The modified model was tested against a previously calibrated model of Detroit Lake on the North Santiam River in northwestern Oregon, and the results compared well. The enhanced model code is being used to evaluate operational and structural scenarios at multiple dam/reservoir systems in the Willamette River basin in Oregon, where downstream temperature management for endangered fish is a high priority for resource managers and dam operators. These updates to the CE-QUAL-W2 blending algorithm allow scenarios involving complicated dam operations and/or hypothetical outlet structures to be evaluated more efficiently with the model, with decreased need for multiple/iterative model runs or preprocessing of model inputs to fully characterize the operational constraints.

  7. Biodegradable polymer based ternary blends for removal of trace metals from simulated industrial wastewater.

    PubMed

    Prakash, N; Arungalai Vendan, S

    2016-02-01

    The ternary blends consisting of Chitosan (CS), Nylon 6 (Ny 6) and Montmorillonite clay (MM clay) were prepared by the solution blending method with glutaraldehyde. The prepared ternary blends were characterization by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermo gravimetric analysis (TGA), Differential scanning calorimetry (DSC) and Scanning electron microscope (SEM). The FTIR results showed that the strong intermolecular hydrogen bondings were established between chitosan, nylon 6 and montmorillonite clay. TGA showed the thermal stability of the blend is enhanced by glutaraldehyde as Crosslink agent. Results of XRD indicated that the relative crystalline of the pure chitosan film was reduced when the polymeric network was reticulated by glutaraldehyde. Finally, the results of scanning electron microscopy (SEM) indicated that the morphology of the blend was rough and heterogenous. Further, it confirms the interaction between the functional groups of the blend components. The extent of removal of the trace metals was found to be almost the same. The removal of these metals at different pH was also done and the maximum removal of the metals was observed at pH 4.5 for both trace metals. Adsorption studies and kinetic analysis have also been made. Moreover, the protonation of amine groups is induced an electrostatic repulsion of cations. When the pH of the solution was more than 5.5, the sorption rate began to decrease. Besides, the quantity of adsorbate on absorbent was fitted as a function in Langmuir and Freundlich isotherm. The sorption kinetics was tested for pseudo first order and pseudo second order reaction. The kinetic experimental data correlated with the second order kinetic model and rate constants of sorption for kinetic models were calculated and accordingly, the correlation coefficients were obtained. Copyright © 2016. Published by Elsevier B.V.

  8. 40 CFR 60.41b - Definitions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Society of Testing and Materials in ASTM D3699 (incorporated by reference, see § 60.17), biodiesel as... § 60.17), or biodiesel blends as defined by the American Society of Testing and Materials in ASTM D7467...

  9. 40 CFR 60.41b - Definitions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Society of Testing and Materials in ASTM D3699 (incorporated by reference, see § 60.17), biodiesel as... § 60.17), or biodiesel blends as defined by the American Society of Testing and Materials in ASTM D7467...

  10. 40 CFR 60.41b - Definitions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Society of Testing and Materials in ASTM D3699 (incorporated by reference, see § 60.17), biodiesel as... § 60.17), or biodiesel blends as defined by the American Society of Testing and Materials in ASTM D7467...

  11. Cross-linked polyvinyl alcohol films as alkaline battery separators

    NASA Technical Reports Server (NTRS)

    Sheibley, D. W.; Manzo, M. A.; Gonzalez-Sanabria, O. D.

    1983-01-01

    Cross-linking methods have been investigated to determine their effect on the performance of polyvinyl alcohol (PVA) films as alkaline battery separators. The following types of cross-linked PVA films are discussed: (1) PVA-dialdehyde blends post-treated with an acid or acid periodate solution (two-step method) and (2) PVA-dialdehyde blends cross-linked during film formation (drying) by using a reagent with both aldehyde and acid functionality (one-step method). Laboratory samples of each cross-linked type of film were prepared and evaluated in standard separator screening tests. Then pilot-plant batches of films were prepared and compared to measure differences due to the cross-linking method. The pilot-plant materials were then tested in nickel oxide-zinc cells to compare the two methods with respect to performance characteristics and cycle life. Cell test results are compared with those from tests with Celgard.

  12. Cross-linked polyvinyl alcohol films as alkaline battery separators

    NASA Technical Reports Server (NTRS)

    Sheibley, D. W.; Manzo, M. A.; Gonzalez-Sanabria, O. D.

    1982-01-01

    Cross-linking methods were investigated to determine their effect on the performance of polyvinyl alcohol (PVA) films as alkaline battery separators. The following types of cross-linked PVA films are discussed: (1) PVA-dialdehyde blends post-treated with an acid or acid periodate solution (two-step method) and (2) PVA-dialdehyde blends cross-linked during film formation (drying) by using a reagent with both aldehyde and acid functionality (one-step method). Laboratory samples of each cross-linked type of film were prepared and evaluated in standard separator screening tests. The pilot-plant batches of films were prepared and compared to measure differences due to the cross-linking method. The pilot-plant materials were then tested in nickel oxide - zinc cells to compare the two methods with respect to performance characteristics and cycle life. Cell test results are compared with those from tests with Celgard.

  13. Antimicrobial activity of blended essential oil preparation.

    PubMed

    Tadtong, Sarin; Suppawat, Supatcha; Tintawee, Anchalee; Saramas, Phanida; Jareonvong, Suchada; Hongratanaworakit, Tapanee

    2012-10-01

    Antimicrobial activities of two blended essential oil preparations comprising lavender oil, petigrain oil, clary sage oil, ylang ylang oil and jasmine oil were evaluated against various pathogenic microorganisms. Both preparations showed antimicrobial activity in the agar disc diffusion assay against the Gram-positive bacteria, Staphylococcus aureus ATCC6538 and S. epidermidis isolated strain, the fungus, Candida albicans ATCC10231, and the Gram-negative bacterium, Escherichia coli ATCC25922, but showed no activity against Pseudomonas aeruginosa ATCC9027. The minimum inhibitory concentration (MIC) of these preparations was evaluated. By the broth microdilution assay, preparation 1, comprising lavender oil, clary sage oil, and ylang ylang oil (volume ratio 3:4:3), exhibited stronger antimicrobial activity than preparation 2, which was composed of petigrain oil, clary sage oil, and jasmine oil (volume ratio 3:4:3). Moreover, the sum of the fractional inhibitory concentrations (Sigma fic) of preparation 1 expressed a synergistic antimicrobial effect against the tested microorganisms (Sigma fic

  14. Preparation and application of agar/alginate/collagen ternary blend functional food packaging films.

    PubMed

    Wang, Long-Feng; Rhim, Jong-Whan

    2015-09-01

    Ternary blend agar/alginate/collagen (A/A/C) hydrogel films with silver nanoparticles (AgNPs) and grapefruit seed extract (GSE) were prepared. Their performance properties, transparency, tensile strength (TS), water vapor permeability (WVP), water contact angle (CA), water swelling ratio (SR), water solubility (WS), and antimicrobial activity were determined. The A/A/C film was highly transparent, and both AgNPs and GSE incorporated blend films (A/A/C(AgNPs) and A/A/C(GSE)) exhibited UV-screening effect, especially, the A/A/C(GSE) film had high UV-screening effect without sacrificing the transmittance. In addition, the A/A/C blend films formed efficient hydrogel film with the water holding capacity of 23.6 times of their weight. Both A/A/C(AgNPs) and A/A/C(GSE) composite films exhibited strong antimicrobial activity against both Gram-positive (Listeria monocytogenes) and Gram-negative (Escherichia coli) food-borne pathogenic bacteria. The test results of fresh potatoes packaging revealed that all the A/A/C ternary blend films prevented forming of condensed water on the packaged film surface, both A/A/C(AgNPs) and A/A/C(GSE) composite films prevented greening of potatoes during storage. The results indicate that the ternary blend hydrogel films incorporated with AgNPs or GSE can be used not only as antifogging packaging films for highly respiring fresh agriculture produce, but also as an active food packaging system utilizing their strong antimicrobial activity. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Studies on the effect of compatibilizers on mechanical, thermal and flow properties of polycarbonate/poly (butylene terephthalate) blends

    NASA Astrophysics Data System (ADS)

    Kumar, Ravindra; Kar, Kamal K.; Kumar, Vijai

    2018-01-01

    Bisphenol-A polycarbonate (PC) and poly(butylene terephthalate) (PBT) were melt blended with ethylene-n-butylacrylate-glycidylmethacrylate terpolymer (E-BA-GMA) at various proportions in order to study the effects of compatibilizers on mechanical, thermal and flow properties of blends. Furthermore, on the basis of this study, PC and PBT were melt-blended at 60/40 proportion with three different compatibilizers viz., ethylene-n-butylacrylate copolymer (E-BA), E-BA-GMA and random copolymer of ethylene and glycidylmethacrylate (E-GMA) at 3 phr loading in a co-rotating twin screw extruder. Tensile, flexural and impact tests were carried out on injection molded samples of PC/PBT blends. The notched izod impact strength increases enormously (˜2-3 times) on addition of any one of the three compatibilizers, and elongation at break (%) also improves tremendously (3, 5 and 4 times) on incorporation of E-BA, E-BA-GMA and E-GMA copolymer, respectively while other mechanical properties decreases slightly (3%-8%) on addition of any one of these compatibilizers. The heat deflection temperature (HDT) raises ˜8 °C-9 °C on addition of either E-BA-GMA or E-GMA, while E-BA shows a negative effect on HDT. The melt flow index diminishes significantly (˜5%-20%) on incorporation of these compatibilizers. The morphology studies via scanning electron microscopy of these four blends were carried out to confirm the mechanical results.

  16. Experimental investigations on a diesel engine operated with fuel blends derived from a mixture of Pakistani waste tyre oil and waste soybean oil biodiesel.

    PubMed

    Qasim, Muhammad; Ansari, Tariq Mahmood; Hussain, Mazhar

    2017-10-18

    The waste tyre and waste cooking oils have a great potential to be used as alternative fuels for diesel engines. The aim of this study was to convert light fractions of pyrolysis oil derived from Pakistani waste vehicle tyres and waste soybean oil methyl esters into valuable fuel and to reduce waste disposal-associated environmental problems. In this study, the waste tyre pyrolysis liquid (light fraction) was collected from commercial tyre pyrolysis plant and biodiesel was prepared from waste soybean oil. The fuel blends (FMWO10, FMWO20, FMWO30, FMWO40 and FMWO50) were prepared from a 30:70 mixture of waste tyre pyrolysis liquid and waste soybean oil methyl esters with different proportions of mineral diesel. The mixture was named as the fuel mixture of waste oils (FMWO). FT-IR analysis of the fuel mixture was carried out using ALPHA FT-IR spectrometer. Experimental investigations on a diesel engine were carried out with various FMWO blends. It was observed that the engine fuel consumption was marginally increased and brake thermal efficiency was marginally decreased with FMWO fuel blends. FMWO10 has shown lowest NOx emissions among all the fuel blends tested. In addition, HC, CO and smoke emissions were noticeably decreased by 3.1-15.6%, 16.5-33.2%, and 1.8-4.5%, respectively, in comparison to diesel fuel, thereby qualifying the blends to be used as alternative fuel for diesel engines.

  17. An investigation into the use of polymer blends to improve the printability of and regulate drug release from pharmaceutical solid dispersions prepared via fused deposition modeling (FDM) 3D printing.

    PubMed

    Alhijjaj, Muqdad; Belton, Peter; Qi, Sheng

    2016-11-01

    FDM 3D printing has been recently attracted increasing research efforts towards the production of personalized solid oral formulations. However, commercially available FDM printers are extremely limited with regards to the materials that can be processed to few types of thermoplastic polymers, which often may not be pharmaceutically approved materials nor ideal for optimizing dosage form performance of poor soluble compounds. This study explored the use of polymer blends as a formulation strategy to overcome this processability issue and to provide adjustable drug release rates from the printed dispersions. Solid dispersions of felodipine, the model drug, were successfully fabricated using FDM 3D printing with polymer blends of PEG, PEO and Tween 80 with either Eudragit E PO or Soluplus. As PVA is one of most widely used polymers in FDM 3D printing, a PVA based solid dispersion was used as a benchmark to compare the polymer blend systems to in terms of processability. The polymer blends exhibited excellent printability and were suitable for processing using a commercially available FDM 3D printer. With 10% drug loading, all characterization data indicated that the model drug was molecularly dispersed in the matrices. During in vitro dissolution testing, it was clear that the disintegration behavior of the formulations significantly influenced the rates of drug release. Eudragit EPO based blend dispersions showed bulk disintegration; whereas the Soluplus based blends showed the 'peeling' style disintegration of strip-by-strip. The results indicated that interplay of the miscibility between excipients in the blends, the solubility of the materials in the dissolution media and the degree of fusion between the printed strips during FDM process can be used to manipulate the drug release rate of the dispersions. This brings new insight into the design principles of controlled release formulations using FDM 3D printing. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. Identification of host fruit volatiles from domestic apple (Malus domestica), native black hawthorn (Crataegus douglasii) and introduced ornamental hawthorn (C. monogyna) attractive to Rhagoletis pomonella flies from the western United States.

    PubMed

    Cha, Dong H; Yee, Wee L; Goughnour, Robert B; Sim, Sheina B; Powell, Thomas H Q; Feder, Jeffrey L; Linn, Charles E

    2012-03-01

    The apple maggot fly, Rhagoletis pomonella, infests apple (Malus domestica) and hawthorn species (most notably the downy hawthorn, Crataegus mollis) in the eastern USA. Evidence suggests that the fly was introduced into the western USA sometime in the last 60 years. In addition to apple, R. pomonella also infests two species of hawthorns in the western USA as major hosts: the native black hawthorn (C. douglasii) and the introduced ornamental English hawthorn, C. monogyna. Apple and downy hawthorn-origin flies in the eastern USA use volatile blends emitted from the surface of their respective ripening fruit to find and discriminate among host trees. To test whether the same is true for western flies, we used coupled gas chromatography and electroantennographic detection (GC-EAD) and developed a 7-component apple fruit blend for western apple-origin flies, an 8-component black hawthorn fruit blend for flies infesting C. douglasii, and a 9-component ornamental hawthorn blend for flies from C. monogyna. Crataegus douglasii and C. monogyna-origin flies showed similar levels of upwind directed flight to their respective natal synthetic fruit blends in flight tunnel assays compared to whole fruit adsorbent extracts, indicating that the blends contain all the behaviorally relevant fruit volatiles to induce maximal response levels. The black and ornamental hawthorn blends shared four compounds in common including 3-methylbutan-1-ol, which appears to be a key volatile for R. pomonella populations in the eastern, southern, and western USA that show a preference for fruit from different Crataegus species. However, the blends also differed from one another and from domesticated apple in several respects that make it possible that western R. pomonella flies behaviorally discriminate among fruit volatiles and form ecologically differentiated host races, as is the case for eastern apple and hawthorn flies.

  19. A Phagostimulant Blend for the Asian Citrus Psyllid.

    PubMed

    Lapointe, Stephen L; Hall, David G; George, Justin

    2016-09-01

    Chemical cues that elicit orientation by the Asian citrus psyllid, Diaphorina citri Kuwayama (Hemiptera: Liviidae), are of interest because it is the primary vector of the causal pathogen of citrus greening disease. Non-pesticidal control methods for D. citri remain a high priority for the citrus industry. While searching for semiochemicals that may be involved in orientation to host plants, we previously identified a blend of formic and acetic acids that stimulated substrate probing by D. citri. Here, we applied geometric mixture designs and response surface modeling to identify and optimize a 3-component blend that further increased the number of salivary sheaths produced by D. citri on a wax substrate containing a 3.5:1.6:1 blend of formic acid, acetic acid, and p-cymene, respectively. No evidence was found for remote orientation by D. citri adults through olfaction to the phagostimulant blends. Increased probing in response to the presence of phagostimulants in the wax matrix occurred after contact with the substrate. Yellow wax beads always attracted more D. citri adults and received more probes compared with white wax beads. Yellow beads containing the 3-component blend of phagostimulants were probed by D. citri 2 to 3 times more often compared with yellow beads alone. The phagostimulant effect also was tested by covering wax beads containing the 3-component blend with a plastic film to minimize olfaction or contact chemoreception by antennation. The plastic film did not affect the probing response, thus suggesting that chemosensation was associated with mouthparts and not olfactory receptors. Salivary sheaths produced in wax beads containing the phagostimulant blend were 4.5 times longer than sheaths produced in beads without tastants. This phenomenon might be used to improve a trap, design an attract-and-kill product, or enhance other means of managing D. citri and citrus greening disease.

  20. Effects of pomegranate and pomegranate-apple blend juices on the growth characteristics of Alicyclobacillus acidoterrestris DSM 3922 type strain vegetative cells and spores.

    PubMed

    Molva, Celenk; Baysal, Ayse Handan

    2015-05-04

    The present study examined the growth characteristics of Alicyclobacillus acidoterrestris DSM 3922 vegetative cells and spores after inoculation into apple, pomegranate and pomegranate-apple blend juices (10, 20, 40 and 80%, v/v). Also, the effect of sporulation medium was tested using mineral [Bacillus acidoterrestris agar (BATA) and Bacillus acidocaldarius agar (BAA)] and non-mineral containing media [potato dextrose agar (PDA) and malt extract agar (MEA)]. The juice samples were inoculated separately with approximately 10(5)CFU/mL cells or spores from different sporulation media and then incubated at 37°C for 336 h. The number of cells decreased significantly with increasing pomegranate juice concentration in the blend juices and storage time (p<0.001). Based on the results, 3.17, 3.53, and 3.72 log cell reductions were observed in 40%, 80% blend and pomegranate juices, respectively while the cell counts attained approximately 7.17 log CFU/mL in apple juice after 336 h. On the other hand, the cell growth was inhibited for a certain time, and then the numbers started to increase after 72 and 144 h in 10% and 20% blend juices, respectively. After 336 h, total population among spores produced on PDA, BATA, BAA and MEA indicated 1.49, 1.65, 1.67, and 1.28 log reductions in pomegranate juice; and 1.51, 1.38, 1.40 and 1.16 log reductions in 80% blend juice, respectively. The inhibitory effects of 10%, 20% and 40% blend juices varied depending on the sporulation media used. The results obtained in this study suggested that pomegranate and pomegranate-apple blend juices could inhibit the growth of A. acidoterrestris DSM 3922 vegetative cells and spores. Copyright © 2015 Elsevier B.V. All rights reserved.

  1. The study on injection parameters of selected alternative fuels used in diesel engines

    NASA Astrophysics Data System (ADS)

    Balawender, K.; Kuszewski, H.; Lejda, K.; Lew, K.

    2016-09-01

    The paper presents selected results concerning fuel charging and spraying process for selected alternative fuels, including regular diesel fuel, rape oil, FAME, blends of these fuels in various proportions, and blends of rape oil with diesel fuel. Examination of the process included the fuel charge measurements. To this end, a set-up for examination of Common Rail-type injection systems was used constructed on the basis of Bosch EPS-815 test bench, from which the high-pressure pump drive system was adopted. For tests concerning the spraying process, a visualisation chamber with constant volume was utilised. The fuel spray development was registered with the use of VisioScope (AVL).

  2. Electrospun nanofibrous SF/P(LLA-CL) membrane: a potential substratum for endothelial keratoplasty.

    PubMed

    Chen, Junzhao; Yan, Chenxi; Zhu, Mengyu; Yao, Qinke; Shao, Chunyi; Lu, Wenjuan; Wang, Jing; Mo, Xiumei; Gu, Ping; Fu, Yao; Fan, Xianqun

    2015-01-01

    Cornea transplant technology has progressed markedly in recent decades, allowing surgeons to replace diseased corneal endothelium by a thin lamellar structure. A thin, transparent, biocompatible, tissue-engineered substratum with corneal endothelial cells for endothelial keratoplasty is currently of interest. Electrospinning a nanofibrous structure can simulate the extracellular matrix and have beneficial effects for cell culture. Silk fibroin (SF) has good biocompatibility but poor mechanical properties, while poly(L-lactic acid-co-ε-caprolactone) (P(LLA-CL)) has good mechanical properties but poor biocompatibility. Blending SF with P(LLA-CL) can maintain the advantages of both these materials and overcome their disadvantages. Blended electrospun nanofibrous membranes may be suitable for regeneration of the corneal endothelium. The aim of this study was to produce a tissue-engineered construct suitable for endothelial keratoplasty. Five scaffolds containing different SF:P(LLA-CL) blended ratios (100:0, 75:25, 50:50, 25:75, 0:100) were manufactured. A human corneal endothelial (B4G12) cell line was cultured on the membranes. Light transmission, speed of cell adherence, cell viability (live-dead test), cell proliferation (Ki-67, BrdU staining), and cell monolayer formation were detected on membranes with the different blended ratios, and expression of some functional genes was also detected by real-time polymerase chain reaction. Different blended ratios of scaffolds had different light transmittance properties. The 25:75 blended ratio membrane had the best transmittance among these scaffolds. All electrospun nanofibrous membranes showed improved speed of cell adherence when compared with the control group, especially when the P(LLA-CL) ratio increased. The 25:75 blended ratio membranes also had the highest cell proliferation. B4G12 cells could form a monolayer on all scaffolds, and most functional genes were also stably expressed on all scaffolds. Only two genes showed changes in expression. All blended ratios of SF:P(LLA-CL) scaffolds were evaluated and showed good biocompatibility for cell adherence and monolayer formation. Among them, the 25:75 blended ratio SF:P(LLA-CL) scaffold had the best transmittance and the highest cell proliferation. These attributes further the potential application of the SF:P(LLA-CL) scaffold for corneal endothelial transplantation.

  3. Qualification of a cyanate ester epoxy blend supplied by Japanese industry for the ITER TF coil insulation

    NASA Astrophysics Data System (ADS)

    Prokopec, R.; Humer, K.; Fillunger, H.; Maix, R. K.; Weber, H. W.; Knaster, J.; Savary, F.

    2012-06-01

    During the last years, two cyanate ester epoxy blends supplied by European and US industry have been successfully qualified for the ITER TF coil insulation. The results of the qualification of a third CE blend supplied by Industrial Summit Technology (IST, Japan) will be presented in this paper. Sets of test samples were fabricated exactly under the same conditions as used before. The reinforcement of the composite consists of wrapped R-glass / polyimide tapes, which are vacuum pressure impregnated with the resin. The mechanical properties of this material were characterized prior to and after reactor irradiation to a fast neutron fluence of 2×1022m-2 (E>0.1 MeV), i.e. twice the ITER design fluence. Static and dynamic tensile as well as static short beam shear tests were carried out at 77 K. In addition, stress strain relations were recorded to determine the Young's modulus at room temperature and at 77 K. The results are compared in detail with the previously qualified materials from other suppliers.

  4. Preparation and characterization of silk sericin/PVA blend film with silver nanoparticles for potential antimicrobial application.

    PubMed

    He, Huawei; Cai, Rui; Wang, Yejing; Tao, Gang; Guo, Pengchao; Zuo, Hua; Chen, Liqun; Liu, Xinyu; Zhao, Ping; Xia, Qingyou

    2017-11-01

    Sericin has great potentials in biomedical applications for its good reactive activity, biocompatibility and biodegradability. However, the undesirable mechanical performance limits its application. Here, we developed a green, facile and economic approach to prepare sericin/polyvinyl alcohol (PVA) blend film. Further, silver nanoparticles (AgNPs) were synthesized in situ on the surface of sericin/PVA film via UV-assisted green synthesis method. Mechanical performance, swelling, mass losing and water retention tests showed the blend film had good mechanical performance, hygroscopicity, water retention capacity and low mass losing ratio. Scanning electron microscopy, fourier transfer infrared spectroscopy, X-ray diffractometry diffraction and X-ray photoelectron spectroscopy indicated the blending of PVA and sericin promoted the formation of hydrogen bond network between sericin and PVA, thus enhanced the mechanical performance and the stability of sericin, as well as the hygroscopicity and water retention capacity. UV irradiation and AgNPs modification did not affect the inner crystalline structure of sericin/PVA blend film. The inhibition zone and bacteria growth curve assay suggested AgNPs-sericin/PVA film had good antibacterial activities against E. coli and S. aureus. This novel AgNPs-sericin/PVA film shows great potentials in biomedical materials such as wound dressing and skin tissue engineering. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. The durability of concrete containing a high-level of fly ash or a ternary blend of supplementary cementing materials

    NASA Astrophysics Data System (ADS)

    Gilbert, Christine M.

    The research for this study was conducted in two distinct phases as follows: Phase 1: The objective was to determine the effect of fly ash on the carbonation of concrete. The specimens made for this phase of the study were larger in size than those normally used in carbonation studies and were are meant to more accurately reflect real field conditions. The results from early age carbonation testing indicate that the larger size specimens do not have a measured depth of carbonation as great as that of the smaller specimens typically used in carbonation studies at the same age and under the same conditions. Phase 2: The objective was to evaluate the performance of ternary concrete mixes containing a ternary cement blend consisting of Portland cement, slag and Type C fly ash. It was found that concrete mixtures containing the fly ash with the lower calcium (CaO) content (in binary or ternary blends) provided superior durability performance and resistance to ASR compared to that of the fly ash with the higher CaO content. Ternary blends (regardless of the CaO content of the fly ash) provided better overall durability performance than binary blends of cementing materials or the control.

  6. Effect of enzymatic hydrolysis of starch on pasting, rheological and viscoelastic properties of milk-barnyard millet (Echinochloa frumentacea) blends meant for spray drying.

    PubMed

    Kumar, P Arun; Pushpadass, Heartwin A; Franklin, Magdaline Eljeeva Emerald; Simha, H V Vikram; Nath, B Surendra

    2016-10-01

    The influence of enzymatic hydrolysis of starch on the pasting properties of barnyard millet was studied using a rheometer. The effects of blending hydrolyzed barnyard millet wort with milk at different ratios (0:1, 1:1, 1:1.5 and 1:2) on flow and viscoelastic behavior were investigated. From the pasting curves, it was evident that enzymatically-hydrolyzed starch did not exhibit typical pasting characteristics expected of normal starch. The Herschel-Bulkley model fitted well to the flow behaviour data, with coefficient of determination (R(2)) ranging from 0.942 to 0.988. All milk-wort blends demonstrated varying degree of shear thinning with flow behavior index (n) ranging from 0.252 to 0.647. Stress-strain data revealed that 1:1 blend of milk to wort had the highest storage modulus (7.09-20.06Pa) and an elastically-dominant behavior (phase angle <45°) over the tested frequency range. The crossover point of G' and G" shifted to higher frequencies with increasing wort content. From the flow and viscoelastic behavior, it was concluded that the 1:1 blend of milk to wort would have least phase separation and better flowability during spray drying. Copyright © 2016 Elsevier B.V. All rights reserved.

  7. Ambipolar Small-Molecule:Polymer Blend Semiconductors for Solution-Processable Organic Field-Effect Transistors.

    PubMed

    Kang, Minji; Hwang, Hansu; Park, Won-Tae; Khim, Dongyoon; Yeo, Jun-Seok; Kim, Yunseul; Kim, Yeon-Ju; Noh, Yong-Young; Kim, Dong-Yu

    2017-01-25

    We report on the fabrication of an organic thin-film semiconductor formed using a blend solution of soluble ambipolar small molecules and an insulating polymer binder that exhibits vertical phase separation and uniform film formation. The semiconductor thin films are produced in a single step from a mixture containing a small molecular semiconductor, namely, quinoidal biselenophene (QBS), and a binder polymer, namely, poly(2-vinylnaphthalene) (PVN). Organic field-effect transistors (OFETs) based on QBS/PVN blend semiconductor are then assembled using top-gate/bottom-contact device configuration, which achieve almost four times higher mobility than the neat QBS semiconductor. Depth profile via secondary ion mass spectrometry and atomic force microscopy images indicate that the QBS domains in the films made from the blend are evenly distributed with a smooth morphology at the bottom of the PVN layer. Bias stress test and variable-temperature measurements on QBS-based OFETs reveal that the QBS/PVN blend semiconductor remarkably reduces the number of trap sites at the gate dielectric/semiconductor interface and the activation energy in the transistor channel. This work provides a one-step solution processing technique, which makes use of soluble ambipolar small molecules to form a thin-film semiconductor for application in high-performance OFETs.

  8. Biogasification of Walt Disney World biomass waste blend. Annual report Jan-Dec 82

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Biljetina, R.; Chynoweth, D.P.; Janulis, J.

    1983-05-01

    The objective of this research is to develop efficient processes for conversion of biomass-waste blends to methane and other resources. To evaluate the technical and economic feasibility, an experimental test facility (ETU) is being designed and installed at the Reedy Creek Wastewater Treatment Plant at Walt Disney World, Orlando, Florida. The facility will integrate a biomethanogenic conversion process with a waste-water treatment process employing water hyacinth ponds for secondary and tertiary treatment of sewage produced at Walt Disney World. The ETU will be capable of feeding 1-wet ton per day of water hyacinth-sludge blends to the digestion system for productionmore » of methane and other byproducts. The detailed design of the facility has been completed and procurement of equipment is in progress.« less

  9. Preferred delivery method and acceptability of Wheat-Soy Blend (WSB++) as a daily complementary food supplement in northwest Bangladesh.

    PubMed

    Shamim, Abu Ahmed; Hanif, Abu A M; Merrill, Rebecca D; Campbell, Rebecca K; Kumkum, Mehnaz Alam; Shaikh, Saijuddin; de Pee, Saskia; Ahmed, Tahmeed; Parveen, Monira; Mehra, Sucheta; Klemm, Rolf D W; Labrique, Alain B; West, Keith P; Christian, Parul

    2015-01-01

    Fortified blended foods (FBFs) are widely used to prevent undernutrition in early childhood in food-insecure settings. We field tested enhanced Wheat Soy Blend (WSB++)-a FBF fortified with micronutrients, milk powder, sugar, and oil-in preparation for a complementary food supplement (CFS) trial in rural northwestern Bangladesh. Formative work was conducted to determine the optimal delivery method (cooked vs. not) for this CFS, to examine mothers' child feeding practices with and acceptance of the WSB++, and to identify potential barriers to adherence. Our results suggest WSB++ is an acceptable CFS in rural Bangladesh and the requirement for mothers to cook WSB++ at home is unlikely to be a barrier to its daily use as a CFS in this population.

  10. Radiation resistant polypropylene blended with mobilizer,. antioxidants and nucleating agent

    NASA Astrophysics Data System (ADS)

    Shamshad, A.; Basfar, A. A.

    2000-03-01

    Post-irradiation storage of medical disposables prepared from isotactic polypropylene renders them brittle due to degradation. To avoid this, isotactic polypropylene [(is)PP] was blended with a mobilizer, dioctyl pthallate (DOP), three antioxidants (hindered amines and a secondary antioxidant) and benzoic acid to obtain radiation-resistant, thermally-stable and transparent material. Different formulations prepared were subjected to gamma radiation to doses of 25 and 50 kGy. Tests of breakage on bending after ageing in an oven at 70°C up to 12 months have shown that the addition of DOP and the antioxidants imparts improved radiation and thermal stability as compared to (is)PP alone or its blend with DOP. All the formulations irradiated or otherwise demonstrated excellent colour stability even after accelerated ageing at 70°C for prolonged periods.

  11. Interfacial adhesion of carbon fibers

    NASA Technical Reports Server (NTRS)

    Bascom, Willard D.

    1987-01-01

    Relative adhesion strengths between AS4, AS1, and XAS carbon fibers and thermoplastic polymers were determined using the embedded single filament test. Polymers studied included polycarbonate, polyphenylene oxide, polyetherimide, polysulfone, polyphenylene oxide blends with polystyrene, and polycarbonate blends with a polycarbonate polysiloxane block copolymer. Fiber surface treatments and sizings improved adhesion somewhat, but adhesion remained well below levels obtained with epoxy matrices. An explanation for the differences between the Hercules and Grafil fibers was sought using X ray photon spectroscopy, wetting, scanning electron microscopy and thermal desorption analysis.

  12. Military Uniforms: Issues Related to the Supply of Flame Resistant Fibers for the Production of Military Uniforms

    DTIC Science & Technology

    2011-06-30

    fibers. A variety of fibers may be used to create a fabric blend, including FR rayon, Nomex®, Twaron®, Kevlar®, FR cotton, polybenzimidazole ( PBI ...as meta-aramids (e.g., Nomex®), modacrylic, PBI , and FR-treated cotton. o For example, the Army is currently testing fabrics in an attempt to...considering fabric blends containing FR-treated cotton as a potential alternative. o The Marine Corps uses PBI fibers in its balaclava (a protective

  13. Procedures for Handling and Chemical Analysis of Sediment and Water Samples,

    DTIC Science & Technology

    1981-05-01

    silts. Particularly suitable for studies of the sediment/ water interface, for studies on depositonal sediment structures. Al pi ne- ravity Cores of 2 m...adverse water quality impacts would occur. Elemental partitioning or sedimentation fractionation studies are the most complex of the tests considered...8217 water %nd blend the core or dredge sample. Place a{js roximalel-i 00 cc of’ the blended sample in an oxygen-free, poly - ca rbor’~ [ ’-l centrifuge bottle

  14. Thermogenic Blend Alone or in Combination with Whey Protein Supplement Stimulates Fat Metabolism and Improves Body Composition in Mice.

    PubMed

    Vieira-Brock, Paula de Lima; Vaughan, Brent M; Vollmer, David L

    2018-01-01

    Certain food ingredients promote thermogenesis and fat loss. Similarly, whey protein improves body composition. Due to this potential synergistic effect, a blend of thermogenic food ingredients containing African mango, citrus fruit extract, Coleus forskohlii , dihydrocapsiate, and red pepper was tested alone and in combination with a whey protein supplement for its effects on body composition in sedentary mice during high-fat diet. The objective of this study was to evaluate the interaction of thermogenic foods on improving body composition during consumption of an unhealthy diet. C57BL/6J young adult male mice ( n = 12) were placed on a 60% high-fat diet for 4 weeks and subsequently randomly assigned to receive daily dosing by oral gavage of vehicle, the novel blend alone or with whey protein supplement for another 4 weeks. Body composition, thermal imaging of brown adipose tissue (BAT), mitochondrial BAT uncoupling protein 1 (UCP1), and plasma levels of leptin were assessed. Novel blend alone and in combination with protein supplement attenuated body weight gain, fat, and increased surface BAT temperature in comparison to vehicle control and to baseline ( P < 0.5). The combination of novel blend and whey protein supplement also significantly increased UCP1 protein expression in BAT mitochondria in comparison to vehicle control and novel blend alone ( P < 0.5). These data indicate that this novel blend stimulates thermogenesis and attenuates the gain in body weight and fat in response to high-fat diet in mice and these effects were improved when administered in combination with whey protein supplement. 30 days oral administration to mice of a novel blend containing African mango seed extract, citrus fruits extract, Coleus forskohlii root extract, dihydrocapsiate and red pepper fruit extract reduced body weight and fat gain in response to high-fat diet without impairing muscle mass.The novel blend stimulated thermogenesis as shown by the increased thermal imaging and UCP1 protein expression in brown adipose tissue, indicating that improvement in body composition potentially occurred due to a fat-burning effect.The positive effects on body weight, fat, and thermogenesis were improved when the novel blend was administered in combination with a whey protein supplement suggesting that protein provides a synergistic fat-burning effect. Abbreviations Used: BAT: Brown adipose tissue, UCP1: Uncoupling protein 1, DEXA: Dual-energy X-ray absorptiometry.

  15. Analytical characterization of products obtained from slow pyrolysis of Calophyllum inophyllum seed cake: study on performance and emission characteristics of direct injection diesel engine fuelled with bio-oil blends.

    PubMed

    Rajamohan, Sakthivel; Kasimani, Ramesh

    2018-04-01

    This paper aims to analyse the characteristics and properties of the fractions obtained from slow pyrolysis of non-edible seed cake of Calophyllum inophyllum (CI). The gas, bio-oil and biochar obtained from the pyrolysis carried out at 500 °C in a fixed bed batch type reactor at a heating rate of 30 °C/min were characterized by various analytical techniques. Owing to the high volatile content of CI biomass (72.61%), it was selected as the raw material in this present investigation. GC-MS and FT-IR analysis of bio-oil showed the presence of higher amount of oxygenated compounds, phenol derivatives, esters, acid and furans. The physicochemical properties of the bio-oil were tested as per ASTM norms which imply that bio-oil is a highly viscous liquid with lower heating value as compared to that of diesel fuel. The chemical composition of evolved gas was analysed by using GC testing which revealed the presence of combustible components. The FT-IR characterization of biochar showed the presence of aliphatic and aromatic hydrocarbons whereas the elevated amount of carbon in biochar indicates its potential to be used as solid fuel. The performance and emission characteristics of CI engine were assessed with different CI bio-oil blends and compared with baseline diesel fuel. The results showed that addition of bio-oil leads to decreased brake thermal efficiency and increased brake specific energy consumption. Meanwhile, increase in blend ratio reduces harmful pollutants such as oxides of nitrogen and smoke in the exhaust. From the engine testing, it is suggested to employ 20% of CI bio-oil blends in CI engine to obtain better operation.

  16. Behavioral and Antennal Responses of Drosophila suzukii (Diptera: Drosophilidae) to Volatiles From Fruit Extracts.

    PubMed

    Abraham, John; Zhang, Aijun; Angeli, Sergio; Abubeker, Sitra; Michel, Caryn; Feng, Yan; Rodriguez-Saona, Cesar

    2015-04-01

    Native to Southeast Asia, the spotted wing drosophila, Drosophila suzukii Matsumura (Diptera: Drosophilidae), has become a serious pest of soft-skinned fruit crops since its introduction into North America and Europe in 2008. Current monitoring strategies use baits based on fermentation products; however, to date, no fruit-based volatile blends attractive to this fly have been identified. This is particularly important because females are able to cut into the epicarp of ripening fruit for oviposition. Thus, we conducted studies to: 1) investigate the behavioral responses of adult D. suzukii to volatiles from blueberry, cherry, raspberry, and strawberry fruit extracts; 2) identify the antennally active compounds from the most attractive among the tested extracts (raspberry) using gas chromatography (GC)-mass spectrometry and coupled gas chromatography -electroantennographic detection (GC-EAD); and 3) test a synthetic blend containing the EAD-active compounds identified from raspberry extract on adult attraction. In olfactometer studies, both female and male D. suzukii were attracted to all four fruit extracts. The attractiveness of the fruit extracts ranks as: raspberry ≥ strawberry > blueberry ≥ cherry. GC analyses showed that the fruit extracts emit distinct volatile compounds. In GC-EAD experiments, 11 raspberry extract volatiles consistently elicited antennal responses in D. suzukii. In choice test bioassays, a synthetic EAD-active blend attracted more D. suzukii than a blank control, but was not as attractive as the raspberry extract. To our knowledge, this is the first report of a behaviorally and antennally active blend of host fruit volatiles attractive to D. suzukii, offering promising opportunities for the development of improved monitoring and behaviourally based management tools. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  17. Adaptive neuro-fuzzy inference system (ANFIS) to predict CI engine parameters fueled with nano-particles additive to diesel fuel

    NASA Astrophysics Data System (ADS)

    Ghanbari, M.; Najafi, G.; Ghobadian, B.; Mamat, R.; Noor, M. M.; Moosavian, A.

    2015-12-01

    This paper studies the use of adaptive neuro-fuzzy inference system (ANFIS) to predict the performance parameters and exhaust emissions of a diesel engine operating on nanodiesel blended fuels. In order to predict the engine parameters, the whole experimental data were randomly divided into training and testing data. For ANFIS modelling, Gaussian curve membership function (gaussmf) and 200 training epochs (iteration) were found to be optimum choices for training process. The results demonstrate that ANFIS is capable of predicting the diesel engine performance and emissions. In the experimental step, Carbon nano tubes (CNT) (40, 80 and 120 ppm) and nano silver particles (40, 80 and 120 ppm) with nanostructure were prepared and added as additive to the diesel fuel. Six cylinders, four-stroke diesel engine was fuelled with these new blended fuels and operated at different engine speeds. Experimental test results indicated the fact that adding nano particles to diesel fuel, increased diesel engine power and torque output. For nano-diesel it was found that the brake specific fuel consumption (bsfc) was decreased compared to the net diesel fuel. The results proved that with increase of nano particles concentrations (from 40 ppm to 120 ppm) in diesel fuel, CO2 emission increased. CO emission in diesel fuel with nano-particles was lower significantly compared to pure diesel fuel. UHC emission with silver nano-diesel blended fuel decreased while with fuels that contains CNT nano particles increased. The trend of NOx emission was inverse compared to the UHC emission. With adding nano particles to the blended fuels, NOx increased compared to the net diesel fuel. The tests revealed that silver & CNT nano particles can be used as additive in diesel fuel to improve combustion of the fuel and reduce the exhaust emissions significantly.

  18. Investigation on the emission quality, performance and combustion characteristics of the compression ignition engine fueled with environmental friendly corn oil methyl ester - Diesel blends.

    PubMed

    Nagaraja, S; Soorya Prakash, K; Sudhakaran, R; Sathish Kumar, M

    2016-12-01

    This paper deals with emission quality of diesel engine based on eco toxicological studies with different methods of environmental standard toxicity tests satisfy the Bharath and European emission norms. Based on the emission norms, Corn Oil Methyl Ester (COME) with diesel is tested in a compression ignition engine and the performance and combustion characteristics are discussed. The corn oil was esterified and the property of corn oil methyl ester was within the limits specified in ASTM D 6751-03. The COME was blended together with diesel in different proportion percentages along with B20, B40, B60, B80, and B100. The emission and performance tests for various blends of COME was carried out using single cylinder, four stroke diesel engine, and compared with the performance obtained with 100% diesel (D100). The results give clear information that COME has low exhaust emissions and increase in performance compared to D100 without any modifications. It gives better performance, which is nearer to the obtained results of D100. Specific Fuel Consumption (SFC) of B100 at the full load condition is found to be 4% lower than that of (D100). The maximum Brake Thermal Efficiency (BTE) of B100 is found to be 8.5% higher than that of the D100 at full load. Also, the maximum BTE of part load for different blends is varied from 5.9% to 7.45% which is higher than D100. The exhaust gas emissions like Carbon Monoxide (CO), Carbon Dioxide (CO 2 ), Hydro Carbon (HC) and Nitrogen Oxide (NO x ) are found to be 2.3 to 18.8% lower compared to D100 for part as well as full load. The heat release rate of biodiesel and it blends are found to 16% to 35% lower as compared to D100 for part load, where as for full load it is 21% lower than D100. The results showed that the test of emissions norms are well within the limits of Bharath VI and European VI and it leads to less pollution, less effect on green eco system and potential substitute to fossil fuels. Copyright © 2016 Elsevier Inc. All rights reserved.

  19. Catalytic combustion of coal-derived liquids

    NASA Technical Reports Server (NTRS)

    Bulzan, D. L.; Tacina, R. R.

    1981-01-01

    A noble metal catalytic reactor was tested with three grades of SRC 2 coal derived liquids, naphtha, middle distillate, and a blend of three parts middle distillate to one part heavy distillate. A petroleum derived number 2 diesel fuel was also tested to provide a direct comparison. The catalytic reactor was tested at inlet temperatures from 600 to 800 K, reference velocities from 10 to 20 m/s, lean fuel air ratios, and a pressure of 3 x 10 to the 5th power Pa. Compared to the diesel, the naphtha gave slightly better combustion efficiency, the middle distillate was almost identical, and the middle heavy blend was slightly poorer. The coal derived liquid fuels contained from 0.58 to 0.95 percent nitrogen by weight. Conversion of fuel nitrogen to NOx was approximately 75 percent for all three grades of the coal derived liquids.

  20. 40 CFR 63.750 - Test methods and procedures.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 11 2014-07-01 2014-07-01 false Test methods and procedures. 63.750...) National Emission Standards for Aerospace Manufacturing and Rework Facilities § 63.750 Test methods and... engineering reference texts, or other equivalent methods. (2) The composite vapor pressure of a blended hand...

  1. Flight Testing the X-48B at the Dryden Flight Research Center

    NASA Technical Reports Server (NTRS)

    Cosenito, Gary B.

    2010-01-01

    Topics discussed include: a) UAV s at NASA Dryden, Past and Present; b) Why Do We Flight Test?; c) The Blended (or Hybrid) Wing-Body Advantage; d) Program Objectives; e) The X-48B Vehicle and Ground Control Station; and f) Flight Test Highlights & Video.

  2. 40 CFR 86.213 - Fuel specifications.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Passenger Vehicles; Cold Temperature Test Procedures § 86.213 Fuel specifications. (a) Gasoline. Use a gasoline test fuel with ethanol (low-level blend only) or without ethanol as follows: (1) You must certify using service accumulation fuel and E10 test fuel as specified in § 86.113 for any vehicles required to...

  3. Effect of organoclay on morphology and properties of linear low density polyethylene and Vietnamese cassava starch biobased blend.

    PubMed

    Nguyen, D M; Vu, T T; Grillet, Anne-Cécile; Ha Thuc, H; Ha Thuc, C N

    2016-01-20

    Linear low density polyethylene (LLDPE)/thermal plastic starch (TPS) blend was studied to prepare the biobased nanocomposite material using organoclay nanofil15 (N15) modified by alkilammonium as the reinforced phase. The LLDPE/TPS blend and its nanocomposites were elaborated by melt mixing method at 160 °C for 7 min. And the compounded sample was filmed by blowing method at three different zones of temperature profile which are 160-170-165 °C. The good dispersion of clay in the polymer blend matrix is showed by X-ray diffraction (XRD) and transmission electronic microscopy (TEM), and a semi-exfoliated structure was obtained. The thermal and mechanical properties of materials are enhanced when N15 is added to the mixture. The effect of N15 on morphology and particles size of TPS phase is also investigated. The biodegradation test shows that more than 60% in weight of LLDPE/TPS film is degraded into CO2, H2O, methane and biomass after 5 months in compost soil. Copyright © 2015 Elsevier Ltd. All rights reserved.

  4. Blending of phased array data

    NASA Astrophysics Data System (ADS)

    Duijster, Arno; van Groenestijn, Gert-Jan; van Neer, Paul; Blacquière, Gerrit; Volker, Arno

    2018-04-01

    The use of phased arrays is growing in the non-destructive testing industry and the trend is towards large 2D arrays, but due to limitations, it is currently not possible to record the signals from all elements, resulting in aliased data. In the past, we have presented a data interpolation scheme `beyond spatial aliasing' to overcome this aliasing. In this paper, we present a different approach: blending and deblending of data. On the hardware side, groups of receivers are blended (grouped) in only a few transmit/recording channels. This allows for transmission and recording with all elements, in a shorter acquisition time and with less channels. On the data processing side, this blended data is deblended (separated) by transforming it to a different domain and applying an iterative filtering and thresholding. Two different filtering methods are compared: f-k filtering and wavefield extrapolation filtering. The deblending and filtering methods are demonstrated on simulated experimental data. The wavefield extrapolation filtering proves to outperform f-k filtering. The wavefield extrapolation method can deal with groups of up to 24 receivers, in a phased array of 48 × 48 elements.

  5. Nitrogen evolution during the co-combustion of hydrothermally treated municipal solid waste and coal in a bubbling fluidized bed.

    PubMed

    Lu, Liang; Jin, Yuqi; Liu, Hongmei; Ma, Xiaojun; Yoshikawa, Kunio

    2014-01-01

    Nitrogen evolution was studied during the co-combustion of hydrothermally treated municipal solid wastes (HT MSW) and coal in a bubbling fluidized bed (BFB). HT MSW blending ratios as 10%, 20% and 30% (wt.%) were selected and tested at 700, 800, 900 °C. Emissions of NO and N2O from blends were measured and compared with the results of mono-combustion trials. Moreover, concentrations of precursors like NH3 and HCN were also quantified. The results are summarized as follows: NO emissions were predominant in all the cases, which rose with increasing temperature. The blending of HT MSW contributed to the NO reduction. N2O emissions decreased with temperature rising and the blending of HT MSW also presented positive effects. At 30% HT MSW addition, both NO and N2O emissions showed the lowest values (391.85 ppm and 55.33 ppm, respectively at 900 °C). For the precursors, more HCN was detected than NH3 and both played important roles on the gas side nitrogen evolution. Copyright © 2013. Published by Elsevier Ltd.

  6. Preparation and characterization of composites based on the blends of collagen, chitosan and hyaluronic acid with nano-hydroxyapatite.

    PubMed

    Sionkowska, Alina; Kaczmarek, Beata

    2017-09-01

    3D porous composites based on the blend of chitosan, collagen and hyaluronic acid with the addition of nano-hydroxyapatite were prepared. SEM images for the composites were made and the structure was assessed. Mechanical properties were studied using a Zwick&Roell Testing Mashine. In addition, the porosity and density of composites were measured. The concentration of calcium ions released from the material was detected by the complexometric titration method. The results showed that in 3D porous sponge based on the blend of chitosan, collagen and hyaluronic acid, inorganic particles of nanohydroxyapatite can be incorporated, as well as that the properties of 3D composites depend on the material composition. Mechanical parameters and thermal stability of ternary biopolymeric blends were improved by the addition of hydroxyapatite. Moreover, the porosity of ternary materials was higher than in materials based on pure chitosan or collagen. All composites were characterized by a porous structure with interconnected pores. Calcium ions can be released from the composite during its degradation in water. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Experimental studies on natural aspirated diesel engine fuelled with corn seed oil methyl ester as a bio-diesel.

    NASA Astrophysics Data System (ADS)

    Rama Krishna Reddy, E.; Dhana Raju, V.

    2018-03-01

    This paper evaluates the possibilities of using corn seed oil methyl ester as a fuel for compression ignition engines. The biodiesels are contained high oxygen content, and high Cetane number, due to this properties efficiency of biodiesel is higher than diesel fuel. The experiments were conducted with different biodiesel blends of (B10, B15, B20 and B25) corn seed oil on single cylinder four stroke natural aspirated diesel engines. Performance parameters and exhaust emissions are investigated in this experimental with the blends of the corn seed oil methyl ester and diesel fuel. The test results showed that the bio-diesel blends gives improved results for brake thermal efficiency and specific fuel consumption when compared with the diesel fuel. The emissions of corn seed methyl esters follow the same trend of diesel but the smoke opacity was reduces for all blends. From the investigation, corn seed methyl ester is also having the properties similar to diesel fuel; it is biodegradable and renewable fuel, so it will be used as an alternative for diesel fuel.

  8. Preparation and characterization of poly (hydroxy butyrate)/chitosan blend scaffolds for tissue engineering applications

    PubMed Central

    Karbasi, Saeed; Khorasani, Saied Nouri; Ebrahimi, Somayeh; Khalili, Shahla; Fekrat, Farnoosh; Sadeghi, Davoud

    2016-01-01

    Background: Poly (hydroxy butyrate) (PHB) is a biodegradable and biocompatible polymer with good mechanical properties. This polymer could be a promising material for scaffolds if some features improve. Materials and Methods: In the present work, new PHB/chitosan blend scaffolds were prepared as a three-dimensional substrate in cartilage tissue engineering. Chitosan in different weight percent was added to PHB and solved in trifluoroacetic acid. Statistical Taguchi method was employed in the design of experiments. Results: The Fourier-transform infrared spectroscopy test revealed that the crystallization of PHB in these blends is suppressed with increasing the amount of chitosan. Scanning electron microscopy images showed a thin and rough top layer with a nodular structure, supported with a porous sub-layer in the surface of the scaffolds. In vitro degradation rate of the scaffolds was higher than pure PHB scaffolds. Maximum degradation rate has been seen for the scaffold with 90% wt. NaCl and 40% wt. chitosan. Conclusions: The obtained results suggest that these newly developed PHB/chitosan blend scaffolds may serve as a three-dimensional substrate in cartilage tissue engineering. PMID:28028517

  9. Preparation and characterization of poly (hydroxy butyrate)/chitosan blend scaffolds for tissue engineering applications.

    PubMed

    Karbasi, Saeed; Khorasani, Saied Nouri; Ebrahimi, Somayeh; Khalili, Shahla; Fekrat, Farnoosh; Sadeghi, Davoud

    2016-01-01

    Poly (hydroxy butyrate) (PHB) is a biodegradable and biocompatible polymer with good mechanical properties. This polymer could be a promising material for scaffolds if some features improve. In the present work, new PHB/chitosan blend scaffolds were prepared as a three-dimensional substrate in cartilage tissue engineering. Chitosan in different weight percent was added to PHB and solved in trifluoroacetic acid. Statistical Taguchi method was employed in the design of experiments. The Fourier-transform infrared spectroscopy test revealed that the crystallization of PHB in these blends is suppressed with increasing the amount of chitosan. Scanning electron microscopy images showed a thin and rough top layer with a nodular structure, supported with a porous sub-layer in the surface of the scaffolds. In vitro degradation rate of the scaffolds was higher than pure PHB scaffolds. Maximum degradation rate has been seen for the scaffold with 90% wt. NaCl and 40% wt. chitosan. The obtained results suggest that these newly developed PHB/chitosan blend scaffolds may serve as a three-dimensional substrate in cartilage tissue engineering.

  10. Property tuning of poly(lactic acid)/cellulose bio-composites through blending with modified ethylene-vinyl acetate copolymer.

    PubMed

    Pracella, Mariano; Haque, Md Minhaz-Ul; Paci, Massimo; Alvarez, Vera

    2016-02-10

    The effect of addition of an ethylene-vinyl acetate copolymer modified with glycidyl methacrylate (EVA-GMA) on the structure and properties of poly(lactic acid) (PLA) composites with cellulose micro fibres (CF) was investigated. Binary (PLA/CF) and ternary (PLA/EVA-GMA/CF) composites obtained by melt mixing in Brabender mixer were analysed by SEM, POM, WAXS, DSC, TGA and tensile tests. The miscibility and morphology of PLA/EVA-GMA blends were first examined as a function of composition: a large rise of PLA spherulite growth rate in the blends was discovered with increasing the EVA-GMA content (0-30 wt%) in the isothermal crystallization both from the melt and the solid state. PLA/EVA-GMA/CF ternary composites displayed improved adhesion and dispersion of fibres into the matrix as compared to PLA/CF system. Marked changes of thermodynamic and tensile parameters, as elastic modulus, strength and elongation at break were observed for the composites, depending on blend composition, polymer miscibility and fibre-matrix chemical interactions at the interface. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Differential Attraction of Malaria Mosquitoes to Volatile Blends Produced by Human Skin Bacteria

    PubMed Central

    Verhulst, Niels O.; Andriessen, Rob; Groenhagen, Ulrike; Bukovinszkiné Kiss, Gabriella; Schulz, Stefan; Takken, Willem; van Loon, Joop J. A.; Schraa, Gosse; Smallegange, Renate C.

    2010-01-01

    The malaria mosquito Anopheles gambiae sensu stricto is mainly guided by human odour components to find its blood host. Skin bacteria play an important role in the production of human body odour and when grown in vitro, skin bacteria produce volatiles that are attractive to A. gambiae. The role of single skin bacterial species in the production of volatiles that mediate the host-seeking behaviour of mosquitoes has remained largely unknown and is the subject of the present study. Headspace samples were taken to identify volatiles that mediate this behaviour. These volatiles could be used as mosquito attractants or repellents. Five commonly occurring species of skin bacteria were tested in an olfactometer for the production of volatiles that attract A. gambiae. Odour blends produced by some bacterial species were more attractive than blends produced by other species. In contrast to odours from the other bacterial species tested, odours produced by Pseudomonas aeruginosa were not attractive to A. gambiae. Headspace analysis of bacterial volatiles in combination with behavioural assays led to the identification of six compounds that elicited a behavioural effect in A. gambiae. Our results provide, to our knowledge, the first evidence for a role of selected bacterial species, common on the human skin, in determining the attractiveness of humans to malaria mosquitoes. This information will be used in the further development of a blend of semiochemicals for the manipulation of mosquito behaviour. PMID:21209854

  12. Recycled asphalt pavement - fly ash geopolymer as a sustainable stabilized pavement material

    NASA Astrophysics Data System (ADS)

    Horpibulsuk, S.; Hoy, M.; Witchayaphong, P.; Rachan, R.; Arulrajah, A.

    2017-11-01

    Strength, durability, microstructure and leachate characteristics of Recycled Asphalt Pavement and Fly Ash (RAP-FA) geopolymers and RAP-FA blends as a sustainable pavement material are evaluated in this paper. The strength development of the stabilized materials with and without effect wetting-drying (w-d) cycles was determined by Unconfined Compression Strength (UCS) test. The mineralogical and microstructural changes of the stabilized material were analyzed by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The leachability of the heavy metals were measured by Toxicity Characteristic Leaching Procedure (TCLP) and compared with international standard. The results show that both RAP-FA blend and RAP-FA geopolymer increase with increasing the number of w-d cycles (C), reaching its peak at 6 w-d cycles. The XRD and SEM analyses indicate that the strength development of RAP-FA blend occurs due to stimulation of the chemical reaction between the high amount to Calcium in RAP and the high amount of Silica and Alumina in FA leaching to production of Calcium Aluminium (Silicate) Hydrate, while the geopolymerization reaction is observed in RAP-FA geopolymer. For C> 6, the significant macro- and micro-cracks developed during w-d cycles cause strength reduction for both RAP-FA blend and geopolymer. The TCLP results demonstrate that there is no environmental risk for these stabilized materials. Furthermore, FA-geopolymer can reduce the leachability of heavy metal in RAP-FA blend. The outcome from this research confirms the viability of using RAP-FA blend and RAP-FA geopolymer as alternative sustainable pavement materials.

  13. High throughput research and evaporation rate modeling for solvent screening for ethylcellulose barrier membranes in pharmaceutical applications.

    PubMed

    Schoener, Cody A; Curtis-Fisk, Jaime L; Rogers, True L; Tate, Michael P

    2016-10-01

    Ethylcellulose is commonly dissolved in a solvent or formed into an aqueous dispersion and sprayed onto various dosage forms to form a barrier membrane to provide controlled release in pharmaceutical formulations. Due to the variety of solvents utilized in the pharmaceutical industry and the importance solvent can play on film formation and film strength it is critical to understand how solvent can influence these parameters. To systematically study a variety of solvent blends and how these solvent blends influence ethylcellulose film formation, physical and mechanical film properties and solution properties such as clarity and viscosity. Using high throughput capabilities and evaporation rate modeling, thirty-one different solvent blends composed of ethanol, isopropanol, acetone, methanol, and/or water were formulated, analyzed for viscosity and clarity, and narrowed down to four solvent blends. Brookfield viscosity, film casting, mechanical film testing and water permeation were also completed. High throughput analysis identified isopropanol/water, ethanol, ethanol/water and methanol/acetone/water as solvent blends with unique clarity and viscosity values. Evaporation rate modeling further rank ordered these candidates from excellent to poor interaction with ethylcellulose. Isopropanol/water was identified as the most suitable solvent blend for ethylcellulose due to azeotrope formation during evaporation, which resulted in a solvent-rich phase allowing the ethylcellulose polymer chains to remain maximally extended during film formation. Consequently, the highest clarity and most ductile films were formed. Employing high throughput capabilities paired with evaporation rate modeling allowed strong predictions between solvent interaction with ethylcellulose and mechanical film properties.

  14. Using 3D Printing for Rapid Prototyping of Characterization Tools for Investigating Powder Blend Behavior.

    PubMed

    Hirschberg, Cosima; Boetker, Johan P; Rantanen, Jukka; Pein-Hackelbusch, Miriam

    2018-02-01

    There is an increasing need to provide more detailed insight into the behavior of particulate systems. The current powder characterization tools are developed empirically and in many cases, modification of existing equipment is difficult. More flexible tools are needed to provide understanding of complex powder behavior, such as mixing process and segregation phenomenon. An approach based on the fast prototyping of new powder handling geometries and interfacing solutions for process analytical tools is reported. This study utilized 3D printing for rapid prototyping of customized geometries; overall goal was to assess mixing process of powder blends at small-scale with a combination of spectroscopic and mechanical monitoring. As part of the segregation evaluation studies, the flowability of three different paracetamol/filler-blends at different ratios was investigated, inter alia to define the percolation thresholds. Blends with a paracetamol wt% above the percolation threshold were subsequently investigated in relation to their segregation behavior. Rapid prototyping using 3D printing allowed designing two funnels with tailored flow behavior (funnel flow) of model formulations, which could be monitored with an in-line near-infrared (NIR) spectrometer. Calculating the root mean square (RMS) of the scores of the two first principal components of the NIR spectra visualized spectral variation as a function of process time. In a same setup, mechanical properties (basic flow energy) of the powder blend were monitored during blending. Rapid prototyping allowed for fast modification of powder testing geometries and easy interfacing with process analytical tools, opening new possibilities for more detailed powder characterization.

  15. Communication in mental health nursing - Bachelor Students' appraisal of a blended learning training programme - an exploratory study.

    PubMed

    Furnes, Merete; Kvaal, Kari Sofie; Høye, Sevald

    2018-01-01

    It is important that mental health nursing students at Bachelor level obtain effective communication skills. Many students dread the fact that in the mental health field they will encounter patients and relatives with various backgrounds and personalities. Large classes and limited teaching resources in nursing education are challenging. To prepare students for mental health nursing practice, a communication skills course based on the blended learning method was developed and carried out at two different campuses.The aim of the study is to explore Bachelor nursing students' appraisal of blended learning methods for enhancing communication skills in mental health nursing. This study employed an exploratory design. Teaching and information materials were available on the learning management system (LMS). Videotaped role play training was carried out in the Simulation Department. Data were collected after the course by means of a questionnaire with closed and open-ended questions. The response rate was 59.2%. Quantitative data were analysed using the Statistical package for the Social Sciences (SPSS) and the Kruskal Wallis test, while qualitative data were analysed by content analysis based on Graneheim and Lundman's approach. No impact of background variables was observed. Students appreciated teachers' participation in role play and immediate feedback was considered especially important for learning outcomes. The students perceived that their communication skills and knowledge had improved after completing the blended learning programme. According to the nursing students, blended learning is an appropriate method for improving communication skills in preparation for mental health nursing. Blended learning makes it possible to build flexible courses with limited resources.

  16. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Joyce, R.J.; Natusch, D.F.S.; Richardson, D.W.

    Blends of 15% methanol with petrol containing 1% isobutanol have been utilised by 45 vehicles operated for a period of two years. An additional 907 vehicles have been operated for approximately one year to obtain information about the distribution of M15 blends, about necessary co-solvent concentrations, and about general vehicle driveability. Initial studies have also been conducted using 15-20% emulsions of methanol with diesel in diesel-cycle engines. High methanol fuels ranging from M85 to M100 have been tested in six purpose-built vehicles and 45 retrofitted vehicles involving four different types of retrofit systems. In addition, high methanol fuels have alsomore » been tested in dieselcycle engines involving two different types of purpose-built engines, together with unmodified engines.« less

  17. Numerical-experimental investigation of PE/EVA foam injection molded parts

    NASA Astrophysics Data System (ADS)

    Spina, Roberto

    The main objective of the presented work is to propose a robust framework to test foaming injection molded parts, with the aim of establishing a standard testing cycle for the evaluation of a new foam material based on numerical and experimental results. The research purpose is to assess parameters influencing several aspects, such as foam morphology and compression behavior, using useful suggestions from finite element analysis. The investigated polymeric blend consisted of a mixture of low density polyethylenes (LDPEs), a high-density polyethylene (HDPE), an ethylene-vinyl acetate (EVA) and an azodicarbonamide (ADC). The thermal, rheological and compression properties of the blend are fully described, as well as the numerical models and the parameters of the injection molding process.

  18. 40 CFR 1054.145 - Are there interim provisions that apply only for a limited time?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... them to us if we ask for them (see 40 CFR 1068.101(a)(2)). (n) Ethanol-blended test fuel for...) California test fuel. Through model year 2019, you may perform testing with a fuel meeting the requirements... Phase 2 test fuel. Any EPA testing with such an engine family may use either this same certification...

  19. 40 CFR 86.113-15 - Fuel specifications.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Heavy-Duty Vehicles; Test Procedures § 86.113-15 Fuel specifications. Section 86.113-15 includes text... transition to an ethanol-blend test fuel for vehicles certified under subpart S of this part. You may use the test fuels specified in § 86.113-04(a) for vehicles that are not yet subject to testing with the new...

  20. Asphalt compatibility testing using the automated Heithaus titration test

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Pauli, A.T.

    1996-12-31

    The Heithaus titration test or variations of the test have been used for over 35 years to predict compatibilities of blends of asphalts from different crude sources. Asphalt compatibility is determined from three calculated parameters that measure the state of peptization of an asphalt or asphalt blend. The parameter p{sub a} is a measure of the peptizability of the asphaltenes. The parameter p{sub a} is a measure of the peptizing power of the maltenes, and the parameter P, derived from p{sub a} and p{sub o} values, is a measure of the overall state of peptization of the asphalt or asphaltmore » blend. In Heithaus original procedure, samples of asphalt were dissolved in toluene and titrated with n-heptane in order to initiate flocculation. The onset of flocculation was detected either by photography or by spotting a filter paper with a small amount of the titrated solution. Recently, an {open_quotes}automated{close_quotes} procedure, after Hotier and Robin, has been developed for use with asphalt. In the automated method UV-visible spectrophotometric detection measures the onset of flocculation as a peak with the percent transmittance plotted as a function of the volume of titrating solvent added to a solution of asphalt. The automated procedure has proven to be less operator dependent and much faster than the original Heithaus procedure. Results from the automated procedure show the data to be consistent with results from the original, {open_quotes}classical{close_quotes} Heithaus procedure.« less

  1. Blended learning approach improves teaching in a problem-based learning environment in orthopedics - a pilot study.

    PubMed

    Back, David A; Haberstroh, Nicole; Antolic, Andrea; Sostmann, Kai; Schmidmaier, Gerhard; Hoff, Eike

    2014-01-27

    While e-learning is enjoying increasing popularity as adjunct in modern teaching, studies on this topic should shift from mere evaluation of students' satisfaction towards assessing its benefits on enhancement of knowledge and skills. This pilot study aimed to detect the teaching effects of a blended learning program on students of orthopedics and traumatology in the context of a problem-based learning environment. The project NESTOR (network for students in traumatology and orthopedics) was offered to students in a problem-based learning course. Participants completed written tests before and directly after the course, followed by a final written test and an objective structured clinical examination (OSCE) as well as an evaluation questionnaire at the end of the semester. Results were compared within the group of NESTOR users and non-users and between these two groups. Participants (n = 53) rated their experiences very positively. An enhancement in knowledge was found directly after the course and at the final written test for both groups (p < 0.001). NESTOR users scored higher than non-users in the post-tests, while the OSCE revealed no differences between the groups. This pilot study showed a positive effect of the blended learning approach on knowledge enhancement and satisfaction of participating students. However, it will be an aim for the future to further explore the chances of this approach and internet-based technologies for possibilities to improve also practical examination skills.

  2. Blended learning approach improves teaching in a problem-based learning environment in orthopedics - a pilot study

    PubMed Central

    2014-01-01

    Background While e-learning is enjoying increasing popularity as adjunct in modern teaching, studies on this topic should shift from mere evaluation of students’ satisfaction towards assessing its benefits on enhancement of knowledge and skills. This pilot study aimed to detect the teaching effects of a blended learning program on students of orthopedics and traumatology in the context of a problem-based learning environment. Methods The project NESTOR (network for students in traumatology and orthopedics) was offered to students in a problem-based learning course. Participants completed written tests before and directly after the course, followed by a final written test and an objective structured clinical examination (OSCE) as well as an evaluation questionnaire at the end of the semester. Results were compared within the group of NESTOR users and non-users and between these two groups. Results Participants (n = 53) rated their experiences very positively. An enhancement in knowledge was found directly after the course and at the final written test for both groups (p < 0.001). NESTOR users scored higher than non-users in the post-tests, while the OSCE revealed no differences between the groups. Conclusions This pilot study showed a positive effect of the blended learning approach on knowledge enhancement and satisfaction of participating students. However, it will be an aim for the future to further explore the chances of this approach and internet-based technologies for possibilities to improve also practical examination skills. PMID:24690365

  3. Biodegradability and biodegradation rate of poly(caprolactone)-starch blend and poly(butylene succinate) biodegradable polymer under aerobic and anaerobic environment.

    PubMed

    Cho, H S; Moon, H S; Kim, M; Nam, K; Kim, J Y

    2011-03-01

    The biodegradability and the biodegradation rate of two kinds biodegradable polymers; poly(caprolactone) (PCL)-starch blend and poly(butylene succinate) (PBS), were investigated under both aerobic and anaerobic conditions. PCL-starch blend was easily degraded, with 88% biodegradability in 44 days under aerobic conditions, and showed a biodegradation rate of 0.07 day(-1), whereas the biodegradability of PBS was only 31% in 80 days under the same conditions, with a biodegradation rate of 0.01 day(-1). Anaerobic bacteria degraded well PCL-starch blend (i.e., 83% biodegradability for 139 days); however, its biodegradation rate was relatively slow (6.1 mL CH(4)/g-VS day) compared to that of cellulose (13.5 mL CH(4)/g-VS day), which was used as a reference material. The PBS was barely degraded under anaerobic conditions, with only 2% biodegradability in 100 days. These results were consistent with the visual changes and FE-SEM images of the two biodegradable polymers after the landfill burial test, showing that only PCL-starch blend had various sized pinholes on the surface due to attack by microorganisms. This result may be use in deciding suitable final disposal approaches of different types of biodegradable polymers in the future. Copyright © 2010 Elsevier Ltd. All rights reserved.

  4. Development and evaluation of emulsion-liposome blends for resveratrol delivery.

    PubMed

    Hung, Chi-Feng; Chen, Jan-Kan; Liao, Mei-Hui; Lo, Huey-Ming; Fang, Jia-You

    2006-01-01

    Nano- and submicron-sized vesicles are beneficial for the controlled delivery of drugs. Resveratrol, the main active polyphenol in red wine, was incorporated into various combinations of emulsions and liposomes to examine its physicochemical characteristics and cardiovascular protection. The blends of emulsion-liposome were composed of coconut oil, soybean lecithin, glycerol formal, and non-ionic surfactants. Multiple systems were assessed by evaluating the droplet size, surface charge, drug encapsulation, release rate, and stability. The vesicle diameter of the systems ranged from 114 to 195 nm. The liposomal vesicles in the systems had smaller diameters (of 43 approximately 56 nm) (F6 and F7). Drug encapsulation of approximately 70% were achieved by the vesicles. The inclusion of resveratrol in these systems retarded the drug release in both the presence and absence of plasma in vitro. The emulsion-liposome blends which incorporated Brij 98 (F5) exhibited the slowest release at zero-order for resveratrol delivery. Treatment using resveratrol in the blended formulations dramatically inhibited vascular intimal thickening, which was tested in an experimental model in which endothelial injury was produced in normal rat carotid arteries. Intraperitoneal injection of the multiple systems was associated with no or negligible liver and kidney toxicity. We concluded that encapsulation by the emulsion-liposome blends is a potent way to enhance the preventative and therapeutic benefits of resveratrol.

  5. Analysis of Flame Retardancy in Polymer Blends by Synchrotron X-ray K-edge Tomography and Interferometric Phase Contrast Movies.

    PubMed

    Olatinwo, Mutairu B; Ham, Kyungmin; McCarney, Jonathan; Marathe, Shashidhara; Ge, Jinghua; Knapp, Gerry; Butler, Leslie G

    2016-03-10

    Underwriters Laboratories 94 test bars have been imaged with X-ray K-edge tomography between 12 and 32 keV to assess the bromine and antimony concentration gradient across char layers of partially burnt samples. Phase contrast tomography on partially burnt samples showed gas bubbles and dark-field scattering ascribed to residual blend inhomogeneity. In addition, single-shot grating interferometry was used to record X-ray movies of test samples during heating (IR and flame) intended to mimic the UL 94 plastics flammability test. The UL 94 test bars were formulated with varying concentrations of a brominated flame retardant, Saytex 8010, and a synergist, Sb2O3, blended into high-impact polystyrene (HIPS). Depending on the sample composition, samples will pass or fail the UL 94 plastics flammability test. Tomography and interferometry imaging show differences that correlate with UL 94 performance. Key features such as char layer, gas bubble formation, microcracks, and dissolution of the flame retardant in the char layer regions are used in understanding the efficiency of the flame retardant and synergist. The samples that pass the UL 94 test have a thick, highly visible char layer as well as an interior rich in gas bubbles. Growth of gas bubbles from flame-retardant thermal decomposition is noted in the X-ray phase contrast movies. Also noteworthy is an absence of bubbles near the burning surface of the polymer; dark-field images after burning suggest a microcrack structure between interior bubbles and the surface. The accepted mechanism for flame retardant activity includes free radical quenching in the flame by bromine and antimony species. The imaging supports this as well as provides a fast inspection of other parameters, such as viscosity and surface tension.

  6. High explosive corner turning performance and the LANL Mushroom test

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hill, L.G.; Seitz, W.L.; Forest, C.A.

    1997-09-01

    The Mushroom test is designed to characterize the corner turning performance of a new generation of less insensitive booster explosives. The test is described in detail, and three corner turning figures-of-merit are examined using pure TATB (both Livermore`s Ultrafine and a Los Alamos research blend) and PBX9504 as examples.

  7. Stress Corrosion Cracking of Pipeline Steels in Fuel Grade Ethanol and Blends - Study to Evaluate Alternate Standard Tests and Phenomenological Understanding of SCC

    DOT National Transportation Integrated Search

    2011-10-30

    Main aim of this project was to evaluate alternate standard test methods for stress corrosion cracking (SCC) and compare them with the results from slow strain rate test (SSRT) results under equivalent environmental conditions. Other important aim of...

  8. Separator for lithium-sulfur battery based on polymer blend membrane

    NASA Astrophysics Data System (ADS)

    Freitag, Anne; Stamm, Manfred; Ionov, Leonid

    2017-09-01

    In this work we report a novel way of reducing the polysulfide shuttle in lithium-sulfur batteries by a new separator material. Polyvinylsulfate potassium salt (PVSK) as polymeric additive is introduced into a polyvinylidene fluoride-hexafluoropropylene (PVdF-HFP) matrix membrane to improve the battery performance. PVSK is expected to lower the polysulfide mobility due to interaction with the sulfonic group. PVdF-HFP/PVSK blend membranes are prepared and an UV/Vis polysulfide diffusion test clearly demonstrates the positive effect of PVSK. Electrochemical testing reveals a significant improvement of cycling stability up to more than 200 cycles. In addition, the effect of separator porosity to the polysulfide shuttle is investigated with PVdF-HFP membranes of different porosity. A simple polysulfide diffusion test and potentiostatic charge/discharge cycling clearly demonstrate that low separator porosity is favorable in a lithium-sulfur cell.

  9. FY2000 FRED Test Report - Final Report on the Crossflow Filter Optimization with 5.6M Sodium Salt Solution

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Poirier, M.R.

    2001-04-04

    The Filtration Research Engineering Demonstration (FRED) at the University of South Carolina ran a test campaign to confirm the utility of crossflow filtration for use with the MST sorption as a strontium-actinide removal technology that is expected to be coupled with the ion exchange and solvent extraction process alternatives. FRED has a Mott Metallurgical 7 tube filter with individual tubes 10 ft long and 3/4 inch o.d. having a nominal pore size of 0.5 microns. The blend sludge consisted of a 50/50 wt percent mixture of sludge simulants of SRS Tank 40H and Tank 8F simulated sludges previously manufactured atmore » FRED. Monosodium Titanate (MST) was blended with the 50/50 sludge mixture in a proportion of 0.9167 MST-to-Sludge ratio to provide the solids loadings analyzed in this test.« less

  10. Pyrolysis of coal, biomass and their blends: performance assessment by thermogravimetric analysis.

    PubMed

    Ferrara, Francesca; Orsini, Alessandro; Plaisant, Alberto; Pettinau, Alberto

    2014-11-01

    With the aim to support the experimental tests in a gasification pilot plant, the thermal decomposition of coal, biomass and their mixtures has been carried out through a thermogravimetric analysis (TGA) and a simplified kinetic analysis. The TGA of pure fuels indicates the low reactivity of South African coal and the relatively high reactivity of Sardinian Sulcis coal during pyrolysis. Among the tested fuels, biomass (stone pine wood chips) is the most reactive one. These results fully confirm those obtained during the experimental tests in the gasification pilot plant. As for the fuel blends, the analysis shows that the synergic effects between the considered coals and biomass are negligible when they are co-pyrolyzed. The results of the analysis confirm that TGA could be very useful to generally predict the gasification performance and to optimize the experimental campaigns in pilot-scale gasification plants. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. Energy value of poultry byproduct meal and animal-vegetable oil blend for broiler chickens by the regression method.

    PubMed

    Cao, M H; Adeola, O

    2016-02-01

    The energy values of poultry byproduct meal (PBM) and animal-vegetable oil blend (A-V blend) were determined in 2 experiments with 288 broiler chickens from d 19 to 25 post hatching. The birds were fed a starter diet from d 0 to 19 post hatching. In each experiment, 144 birds were grouped by weight into 8 replicates of cages with 6 birds per cage. There were 3 diets in each experiment consisting of one reference diet (RD) and 2 test diets (TD). The TD contained 2 levels of PBM (Exp. 1) or A-V blend (Exp. 2) that replaced the energy sources in the RD at 50 or 100 g/kg (Exp. 1) or 40 or 80 g/kg (Exp. 2) in such a way that the same ratio were maintained for energy ingredients across experimental diets. The ileal digestible energy (IDE), ME, and MEn of PBM and A-V blend were determined by the regression method. Dry matter of PBM and A-V blend were 984 and 999 g/kg; the gross energies were 5,284 and 9,604 kcal/kg of DM, respectively. Addition of PBM to the RD in Exp. 1 linearly decreased (P < 0.05) DM, ileal and total tract of DM, energy and nitrogen digestibilities and utilization. In Exp. 2, addition of A-V blend to the RD linearly increased (P < 0.001) ileal digestibilities and total tract utilization of DM, energy and nitrogen as well as IDE, ME, and MEn. Regressions of PBM-associated IDE, ME, or MEn intake in kcal against PBM intake were: IDE = 3,537x + 4.953, r(2) = 0.97; ME = 3,805x + 1.279, r(2) = 0.97; MEn = 3,278x + 0.164, r(2) = 0.90; and A-V blend as follows: IDE = 10,616x + 7.350, r(2) = 0.96; ME = 10,121x + 0.447, r(2) = 0.99; MEn = 10,124x + 2.425, r(2) = 0.99. These data indicate the respective IDE, ME, MEn values (kcal/kg of DM) of PBM evaluated to be 3,537, 3,805, and 3,278, and A-V blend evaluated to be 10,616, 10,121, and 10,124. © 2015 Poultry Science Association Inc.

  12. Thermogenic Blend Alone or in Combination with Whey Protein Supplement Stimulates Fat Metabolism and Improves Body Composition in Mice

    PubMed Central

    Vieira-Brock, Paula de Lima; Vaughan, Brent M.; Vollmer, David L.

    2018-01-01

    Background: Certain food ingredients promote thermogenesis and fat loss. Similarly, whey protein improves body composition. Due to this potential synergistic effect, a blend of thermogenic food ingredients containing African mango, citrus fruit extract, Coleus forskohlii, dihydrocapsiate, and red pepper was tested alone and in combination with a whey protein supplement for its effects on body composition in sedentary mice during high-fat diet. Objective: The objective of this study was to evaluate the interaction of thermogenic foods on improving body composition during consumption of an unhealthy diet. Materials and Methods: C57BL/6J young adult male mice (n = 12) were placed on a 60% high-fat diet for 4 weeks and subsequently randomly assigned to receive daily dosing by oral gavage of vehicle, the novel blend alone or with whey protein supplement for another 4 weeks. Body composition, thermal imaging of brown adipose tissue (BAT), mitochondrial BAT uncoupling protein 1 (UCP1), and plasma levels of leptin were assessed. Results: Novel blend alone and in combination with protein supplement attenuated body weight gain, fat, and increased surface BAT temperature in comparison to vehicle control and to baseline (P < 0.5). The combination of novel blend and whey protein supplement also significantly increased UCP1 protein expression in BAT mitochondria in comparison to vehicle control and novel blend alone (P < 0.5). Conclusions: These data indicate that this novel blend stimulates thermogenesis and attenuates the gain in body weight and fat in response to high-fat diet in mice and these effects were improved when administered in combination with whey protein supplement. SUMMARY 30 days oral administration to mice of a novel blend containing African mango seed extract, citrus fruits extract, Coleus forskohlii root extract, dihydrocapsiate and red pepper fruit extract reduced body weight and fat gain in response to high-fat diet without impairing muscle mass.The novel blend stimulated thermogenesis as shown by the increased thermal imaging and UCP1 protein expression in brown adipose tissue, indicating that improvement in body composition potentially occurred due to a fat-burning effect.The positive effects on body weight, fat, and thermogenesis were improved when the novel blend was administered in combination with a whey protein supplement suggesting that protein provides a synergistic fat-burning effect. Abbreviations Used: BAT: Brown adipose tissue, UCP1: Uncoupling protein 1, DEXA: Dual-energy X-ray absorptiometry PMID:29568185

  13. Assessment of environmentally friendly fuel emissions from in-use vehicle exhaust: low-blend iso-stoichiometric GEM mixture as example.

    PubMed

    Schifter, Isaac; Díaz-Gutiérrez, Luis; Rodríguez-Lara, René; González-Macías, Carmen; González-Macías, Uriel

    2017-05-01

    Gasoline-ethanol-methanol fuel blends were formulated with the same stoichiometric air-to-fuel ratio and volumetric energy concentration as any binary ethanol-gasoline blend. When the stoichiometric blends operated in a vehicle, the time period, injector voltage, and pressure for each fuel injection event in the engine corresponded to a given stoichiometric air-to-fuel ratio, and the load was essentially constant. Three low oxygen content iso-stoichiometric ternary gasoline-ethanol-methanol fuel blends were prepared, and the properties were compared with regular-type fuel without added oxygen. One of the ternary fuels was tested using a fleet of in-use vehicles for15 weeks and compared to neat gasoline without oxygenated compounds as a reference. Only a small number of publications have compared these ternary fuels in the same engine, and little data exist on the performance and emissions of in-use spark-ignition engines. The total hydrocarbon emissions observed was similar in both fuels, in addition to the calculated ozone forming potential of the tailpipe and evaporative emissions. In ozone non-attainment areas, the original purpose for oxygenate gasolines was to decrease carbon monoxide emissions. The results suggest that the strategy is less effective than expected because there still exist a great number of vehicles that have suffered the progressive deterioration of emissions and do not react to oxygenation, while new vehicles are equipped with sophisticated air/fuel control systems, and oxygenation does not improve combustion because the systems adjust the stoichiometric point, making it insensitive to the origin of the added excess oxygen (fuel or excess air). Graphical abstract Low level ternary blend of gasoline-ethanol-methanol were prepared with the same stoichiometric air-fuel ratio and volumetric energy concentration, based on the volumetric energy density of the pre-blended components. Exhaust and evaporative emissions was compared with a blend having no oxygen in a fleet of 12 in-use vehicles. Vehicles that had suffer a normal deterioration of emissions and do not react to oxygenation, and new vehicles with more sophisticated air/fuel control systems do not improve combustion.

  14. Clinical Value of Dual-energy CT in Detection of Pancreatic Adenocarcinoma: Investigation of the Best Pancreatic Tumor Contrast to Noise Ratio.

    PubMed

    He, Yong-Lan; Zhang, Da-Ming; Xue, Hua-Dan; Jin, Zheng-Yu

    2013-01-01

    Objective To quantitatively compare and determine the best pancreatic tumor contrast to noise ratio (CNR) in different dual-energy derived datasets. Methods In this retrospective, single center study, 16 patients (9 male, 7 female, average age 59.4±13.2 years) with pathologically diagnosed pancreatic cancer were enrolled. All patients received an abdominal scan using a dual source CT scanner 7 to 31 days before biopsy or surgery. After injection of iodine contrast agent, arterial and pancreatic parenchyma phase were scanned consequently, using a dual-energy scan mode (100 kVp/230 mAs and Sn 140 kVp/178 mAs) in the pancreatic parenchyma phase. A series of derived dual-energy datasets were evaluated including non-liner blending (non-linear blending width 0-500 HU; blending center -500 to 500 HU), mono-energetic (40-190 keV), 100 kVp and 140 kVp. On each datasets, mean CT values of the pancreatic parenchyma and tumor, as well as standard deviation CT values of subcutaneous fat and psoas muscle were measured. Regions of interest of cutaneous fat and major psoas muscle of 100 kVp and 140 kVp images were calculated. Best CNR of subcutaneous fat (CNRF) and CNR of the major psoas muscle (CNRM) of non-liner blending and mono-energetic datasets were calculated with the optimal mono-energetic keV setting and the optimal blending center/width setting for the best CNR. One Way ANOVA test was used for comparison of best CNR between different dual-energy derived datasets. Results The best CNRF (4.48±1.29) was obtained from the non-liner blending datasets at blending center -16.6±103.9 HU and blending width 12.3±10.6 HU. The best CNRF (3.28±0.97) was obtained from the mono-energetic datasets at 73.3±4.3 keV. CNRF in the 100 kVp and 140 kVp were 3.02±0.91 and 1.56±0.56 respectively. Using fat as the noise background, all of these images series showed significant differences (P<0.01) except best CNRF of mono-energetic image sets vs. CNRF of 100 kVp image (P=0.460). Similar results were found using muscle as the noise background (mono-energetic image vs. 100 kVp image: P=0.246; mono-energetic image vs. non-liner blending image: P=0.044; others: P<0.01). Conclusion Compared with mono-energetic datasets and low kVp datasets, non-linear blending image at automatically chosen blending width/window provides better tumor to the pancreas CNR, which might be beneficial for better detection of pancreatic tumors.

  15. Impacts of ethanol fuel level on emissions of regulated and unregulated pollutants from a fleet of gasoline light-duty vehicles

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Karavalakis, Georgios; Durbin, Thomas; Shrivastava, ManishKumar B.

    The study investigated the impact of ethanol blends on criteria emissions (THC, NMHC, CO, NOx), greenhouse gas (CO2), and a suite of unregulated pollutants in a fleet of gasoline-powered light-duty vehicles. The vehicles ranged in model year from 1984 to 2007 and included one Flexible Fuel Vehicle (FFV). Emission and fuel consumption measurements were performed in duplicate or triplicate over the Federal Test Procedure (FTP) driving cycle using a chassis dynamometer for four fuels in each of seven vehicles. The test fuels included a CARB phase 2 certification fuel with 11% MTBE content, a CARB phase 3 certification fuel withmore » a 5.7% ethanol content, and E10, E20, E50, and E85 fuels. In most cases, THC and NMHC emissions were lower with the ethanol blends, while the use of E85 resulted in increases of THC and NMHC for the FFV. CO emissions were lower with ethanol blends for all vehicles and significantly decreased for earlier model vehicles. Results for NOx emissions were mixed, with some older vehicles showing increases with increasing ethanol level, while other vehicles showed either no impact or a slight, but not statistically significant, decrease. CO2 emissions did not show any significant trends. Fuel economy showed decreasing trends with increasing ethanol content in later model vehicles. There was also a consistent trend of increasing acetaldehyde emissions with increasing ethanol level, but other carbonyls did not show strong trends. The use of E85 resulted in significantly higher formaldehyde and acetaldehyde emissions than the specification fuels or other ethanol blends. BTEX and 1,3-butadiene emissions were lower with ethanol blends compared to the CARB 2 fuel, and were almost undetectable from the E85 fuel. The largest contribution to total carbonyls and other toxics was during the cold-start phase of FTP.« less

  16. 40 CFR 86.101 - General applicability.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... procedures. For example, if you are testing an ethanol-fueled vehicle, perform diagnostics in your evaporative emission enclosure with ethanol and propane. (9) For exhaust emission testing with ethanol-gasoline blends that have less than 25% ethanol by volume, if you use NMHC-to-NMOG conversion factors...

  17. COBALT: Development of a Platform to Flight Test Lander GN&C Technologies on Suborbital Rockets

    NASA Technical Reports Server (NTRS)

    Carson, John M., III; Seubert, Carl R.; Amzajerdian, Farzin; Bergh, Chuck; Kourchians, Ara; Restrepo, Carolina I.; Villapando, Carlos Y.; O'Neal, Travis V.; Robertson, Edward A.; Pierrottet, Diego; hide

    2017-01-01

    The NASA COBALT Project (CoOperative Blending of Autonomous Landing Technologies) is developing and integrating new precision-landing Guidance, Navigation and Control (GN&C) technologies, along with developing a terrestrial fight-test platform for Technology Readiness Level (TRL) maturation. The current technologies include a third- generation Navigation Doppler Lidar (NDL) sensor for ultra-precise velocity and line- of-site (LOS) range measurements, and the Lander Vision System (LVS) that provides passive-optical Terrain Relative Navigation (TRN) estimates of map-relative position. The COBALT platform is self contained and includes the NDL and LVS sensors, blending filter, a custom compute element, power unit, and communication system. The platform incorporates a structural frame that has been designed to integrate with the payload frame onboard the new Masten Xodiac vertical take-o, vertical landing (VTVL) terrestrial rocket vehicle. Ground integration and testing is underway, and terrestrial fight testing onboard Xodiac is planned for 2017 with two flight campaigns: one open-loop and one closed-loop.

  18. High-alcohol microemulsion fuel performance in a diesel engine

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    West, B.H.; Compere, A.L.; Griffith, W.L.

    1990-01-01

    Incidence of methanol use in diesel engines is increasing rapidly due to the potential to reduce both diesel particulate emissions and petroleum consumption. Because simple alcohols and conventional diesel fuel are normally immiscible, most tests to date have used neat to near-neat alcohol, or blends incorporating surfactants or other alcohols. Alcohol's poor ignition quality usually necssitates the use of often expensive cetane enhancers, full-time glow plugs, or spark assist. Reported herein are results of screening tests of clear microemulsion and micellar fuels which contain 10 to 65% C{sub 1}--C{sub 4} alcohol. Ignition performance and NO emissions were measured for clear,more » stable fuel blends containing alcohols, diesel fuel and additives such as alkyl nitrates, acrylic acids, and several vegetable oil derivatives. Using a diesel engine calibrated with reference fuels, cetane numbers for fifty four blends were estimated. The apparent cetane numbers ranged from around 20 to above 50 with the majority between 30 and 45. Emissions of nitric oxide were measured for a few select fuels and were found to be 10 to 20% lower than No. 2 diesel fuel. 36 refs., 87 figs., 8 tabs.« less

  19. Phenology of semiochemical-mediated host foraging by the western boxelder bug, Boisea rubrolineata, an aposematic seed predator.

    PubMed

    Schwarz, Joseph; Gries, Regine; Hillier, Kirk; Vickers, Neil; Gries, Gerhard

    2009-01-01

    The western boxelder bug (BEB), Boisea rubrolineata (Heteroptera: Rhopalidae), is a specialist herbivore of boxelder trees, Acer negundo. We tested the hypothesis that BEBs use semiochemicals to locate host trees. Headspace volatiles from trees bearing staminate inflorescences ("staminate trees") and from trees bearing pistillate inflorescences ("pistillate trees") were collected throughout the season and bioassayed in Y-tube olfactometer experiments. Headspace extracts of early-season, pollen-bearing staminate trees and midseason pistillate trees with mature samaras (seed pods) attracted female and male BEBs. By using coupled gas chromatographic-electroantennographic detection and gas chromatography-mass spectrometry, we identified and tested a five-component synthetic blend of candidate semiochemicals (hexanol, pentyl acetate, phenylacetonitrile, 2-phenethyl acetate, and trans-nerolidol). This blend attracted females, males, and fifth-instar nymphs. Phenylacetonitrile by itself was as attractive as the five-component blend to both adults and nymphs. By responding to phenylacetonitrile emitted by pollen-bearing staminate trees and pistillate trees with maturing seeds, BEBs appear to track and exploit the availability of nutrient-rich food sources, suggesting that the bugs' reproductive ecology is synchronized to the phenology of their host boxelder tree.

  20. Eucalyptus Biodiesel as an Alternative to Diesel Fuel: Preparation and Tests on DI Diesel Engine

    PubMed Central

    Tarabet, Lyes; Loubar, Khaled; Lounici, Mohand Said; Hanchi, Samir; Tazerout, Mohand

    2012-01-01

    Nowadays, the increasing oil consumption throughout the world induces crucial economical, security, and environmental problems. As a result, intensive researches are undertaken to find appropriate substitution to fossil fuels. In view of the large amount of eucalyptus trees present in arid areas, we focus in this study on the investigation of using eucalyptus biodiesel as fuel in diesel engine. Eucalyptus oil is converted by transesterification into biodiesel. Eucalyptus biodiesel characterization shows that the physicochemical properties are comparable to those of diesel fuel. In the second phase, a single cylinder air-cooled, DI diesel engine was used to test neat eucalyptus biodiesel and its blends with diesel fuel in various ratios (75, 50, and 25 by v%) at several engine loads. The engine combustion parameters such as peak pressure, rate of pressure rise, and heat release rate are determined. Performances and exhaust emissions are also evaluated at all operating conditions. Results show that neat eucalyptus biodiesel and its blends present significant improvements of carbon monoxide, unburned hydrocarbon, and particulates emissions especially at high loads with equivalent performances to those of diesel fuel. However, the NOx emissions are slightly increased when the biodiesel content is increased in the blend. PMID:22675246

Some links on this page may take you to non-federal websites. Their policies may differ from this site.
Top