AM06: the Associative Memory chip for the Fast TracKer in the upgraded ATLAS detector

NASA Astrophysics Data System (ADS)

Annovi, A.; Beretta, M. M.; Calderini, G.; Crescioli, F.; Frontini, L.; Liberali, V.; Shojaii, S. R.; Stabile, A.

2017-04-01

This paper describes the AM06 chip, which is a highly parallel processor for pattern recognition in the ATLAS high energy physics experiment. The AM06 contains memory banks that store data organized in 18 bit words; a group of 8 words is called "pattern". Each AM06 chip can store up to 131 072 patterns. The AM06 is a large chip, designed in 65 nm CMOS, and it combines full-custom memory arrays, standard logic cells and serializer/deserializer IP blocks at 2 Gbit/s for input/output communication. The overall silicon area is 168 mm2 and the chip contains about 421 million transistors. The AM06 receives the detector data for each event accepted by Level-1 trigger, up to 100 kHz, and it performs a track reconstruction based on hit information from channels of the ATLAS silicon detectors. Thanks to the design of a new associative memory cell and to the layout optimization, the AM06 consumption is only about 1 fJ/bit per comparison. The AM06 has been fabricated and successfully tested with a dedicated test system.

Inoculation with arbuscular mycorrhizal fungi suppresses initiation of haustoria in the root hemiparasite Pedicularis tricolor.

PubMed

Li, Ai-Rong; Smith, Sally E; Smith, F Andrew; Guan, Kai-Yun

2012-05-01

Plant parasitism and arbuscular mycorrhizal (AM) associations have many parallels and share a number of regulatory pathways. Despite a rapid increase in investigations addressing the roles of AM fungi in regulating interactions between parasitic plants and their hosts, few studies have tested the effect of AM fungi on the initiation and differentiation of haustoria, the parasite-specific structures exclusively responsible for host attachment and nutrient transfer. In this study, we tested the influence of AM fungi on haustorium formation in a root hemiparasitic plant. Using a facultative root hemiparasitic species (Pedicularis tricolor) with the potential to form AM associations, the effects of inoculation were tested with two AM fungal species, Glomus mosseae and Glomus intraradices, on haustorium initiation in P. tricolor grown alone or with Hordeum vulgare 'Fleet' (barley) as the host plant. This study consisted of two greenhouse pot experiments. Both AM fungal species dramatically suppressed intraspecific haustorium initiation in P. tricolor at a very low colonization level. The suppression over-rode inductive effects of the parasite's host plant on haustoria production and caused significant growth depression of P. tricolor. AM fungi had strong and direct suppressive effects on haustorium formation in the root hemiparasite. The significant role of AM fungi in haustorium initiation of parasitic plants was demonstrated for the first time. This study provides new clues for the regulation of haustorium formation and a route to development of new biocontrol strategies in management of parasitic weeds.

Pharmacological enhancement of cannabinoid CB1 receptor activity elicits an antidepressant-like response in the rat forced swim test.

PubMed

Hill, Matthew N; Gorzalka, Boris B

2005-12-01

These experiments aimed to assess whether enhanced activity at the cannabinoid CB1 receptor elicits antidepressant-like effects. To examine this we administered 1 and 5 mg/kg doses of the endocannabinoid uptake inhibitor AM404; 5 and 25 microg/kg doses of HU-210, a potent CB1 receptor agonist; 1, 2.5 and 5 mg/kg of oleamide, which elicits cannabinoidergic actions; 1 and 5 mg/kg doses of AM 251, a selective CB1 receptor antagonist, as well as 10 mg/kg desipramine (a positive antidepressant control) and measured the duration of immobility, during a 5-min test session of the rat Porsolt forced swim test. Results demonstrated that administration of desipramine reduced immobility duration by about 50% and that all of AM404, oleamide and HU-210 administration induced comparable decreases in immobility that were blocked by pretreatment with AM 251. Administration of the antagonist AM 251 alone had no effect on immobility at either dose. These data suggest that enhancement of CB1 receptor signaling results in antidepressant effects in the forced swim test similar to that seen following conventional antidepressant administration.

Am(VI) Extraction Final Report: FY16

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mincher, Bruce Jay; Grimes, Travis Shane; Tillotson, Richard Dean

This report summarizes activities related to hexavalent Am extraction for FY16, in completion of FCR&D Milestone M3FT-16IN030103027. Activities concentrated on three areas of research: 1) centrifugal contactor hot testing, 2) Am(VI) stability studies, and 3) alternative oxidant studies. A brief summary of each task follows. Hot Testing: A new engineering-scale oxidation and solvent extraction test bed was built at Idaho National Laboratory to allow for solvent extraction testing of minor actinide separation concepts. The test bed consists of an oxidation vessel, filtration apparatus, four, 3D printed, 2-cm diameter centrifugal contactors, feed/product vessels, and sample ports. This system replaced the previousmore » 3 stage, 5-cm contactor test bed that was used for the initial testing in FY14. In the FY16 hot test, a feed simulant was spiked with 243Am and 139Ce and treated with 60 g/L sodium bismuthate for two hours to oxidize the Am(III) to Am(VI). This solution was then pumped through a filter and into the four-stage centrifugal contactor setup. The organic phase solvent formulation was 1 M diethylhexylbutyramide (DEHBA)/dodecane. The test showed that Am(VI) was produced by bismuthate oxidation and the residual oxidant was successfully filtered without back pressure buildup. Sixty-four percent of Am was extracted in the contactors using DEHBA. Both Am and Ce were quantitatively stripped by 0.1 M H2O2. Successful demonstration of the utility of small, printable contactors suggests that hot testing of separations concepts can now be conducted more often, since it is cheaper, generates less waste, and entails much less radcon risk than previous testing. Am(VI) stability: A rigorous examination of reagents was conducted to determine if contaminants could interfere with Am oxidation and extraction. An series of DAm measurements showed that bismuthate particle size, water source, acid quality, and DAAP batch or pre-treatment had little effect on extraction efficiency, with a mean distribution ratio of 3.74 ± 0.5, using 1 M DAAP extraction. Additionally, the purposeful addition of millimolar amounts of nitrite or H2O2 to bismuthate-treated Am solutions did not prevent oxidation, as long as residual solid bismuthate was present. Finally, a series of irradiation experiments using a Nordion Gammacell 220E 60Co source was performed, and kinetic data for the radiolytic reduction of Am(VI) were obtained. Unsurprisingly, it was found that radiolysis reduces Am(VI), but that the presence of Ce(IV) acts as a radioprotection agent, to scavenge radiolytically-produced reducing agents, thereby enhancing the stability of the higher Am oxidation state. Alternative oxidants: To date, sodium bismuthate is the only practical oxidant for Am with utility in solvent extraction. While successful oxidation has been demonstrated with sodium peroxydisulfate, it is impractical for solvent extraction because it is only useful in dilute acid and it introduces sulfate into the process. Oxidation has been demonstrated using silver and cobalt catalyzed ozone, however, reduction upon contact with an organic phase is instantaneous. Oxidation is successful using Cu(III) periodate, and marginally successful in initial testing using DAAP extraction. However, the distribution ratios for the oxidized Am are marginal, because Cu(III) is also rapidly reduced by the organic phase. The possibility may exist that this can be optimized.« less

Porous composite with negative thermal expansion obtained by photopolymer additive manufacturing

NASA Astrophysics Data System (ADS)

Takezawa, Akihiro; Kobashi, Makoto; Kitamura, Mitsuru

2015-07-01

Additive manufacturing (AM) could be a novel method of fabricating composite and porous materials having various effective performances based on mechanisms of their internal geometries. Materials fabricated by AM could rapidly be used in industrial application since they could easily be embedded in the target part employing the same AM process used for the bulk material. Furthermore, multi-material AM has greater potential than usual single-material AM in producing materials with effective properties. Negative thermal expansion is a representative effective material property realized by designing a composite made of two materials with different coefficients of thermal expansion. In this study, we developed a porous composite having planar negative thermal expansion by employing multi-material photopolymer AM. After measurement of the physical properties of bulk photopolymers, the internal geometry was designed by topology optimization, which is the most effective structural optimization in terms of both minimizing thermal stress and maximizing stiffness. The designed structure was converted to a three-dimensional stereolithography (STL) model, which is a native digital format of AM, and assembled as a test piece. The thermal expansions of the specimens were measured using a laser scanning dilatometer. Negative thermal expansion corresponding to less than -1 × 10-4 K-1 was observed for each test piece of the N = 3 experiment.

Application and testing of additive manufacturing for mirrors and precision structures

NASA Astrophysics Data System (ADS)

Sweeney, Michael; Acreman, Martyn; Vettese, Tom; Myatt, Ray; Thompson, Mike

2015-09-01

Additive Manufacturing (aka AM, and 3-D printing) is widely touted in the media as the foundation for the next industrial revolution. Beneath the hype, AM does indeed offer profound advantages in lead-time, dramatically reduced consumption of expensive raw materials, while enabling new and innovative design forms that cannot be produced by other means. General Dynamics and their industry partners have begun to embrace this technology for mirrors and precision structures used in the aerospace, defense, and precision optical instrumentation industries. Aggressively lightweighted, open and closed back test mirror designs, 75-150 mm in size, were first produced by AM from several different materials. Subsequent optical finishing and test experiments have exceeded expectations for density, surface finish, dimensional stability and isotropy of thermal expansion on the optical scale of measurement. Materials currently under examination include aluminum, titanium, beryllium, aluminum beryllium, Inconel 625, stainless steel/bronze, and PEKK polymer.

EFFECT OF AXIAL TIBIAL TORQUE DIRECTION ON ACL RELATIVE STRAIN AND STRAIN RATE IN AN IN VITRO SIMULATED PIVOT LANDING

PubMed Central

Oh, Youkeun K.; Kreinbrink, Jennifer L.; Wojtys, Edward M.; Ashton-Miller, James A.

2011-01-01

Anterior cruciate ligament (ACL) injuries most frequently occur under the large loads associated with a unipedal jump landing involving a cutting or pivoting maneuver. We tested the hypotheses that internal tibial torque would increase the anteromedial (AM) bundle ACL relative strain and strain rate more than would the corresponding external tibial torque under the large impulsive loads associated with such landing maneuvers. Twelve cadaveric female knees [mean (SD) age: 65.0 (10.5) years] were tested. Pretensioned quadriceps, hamstring and gastrocnemius muscle-tendon unit forces maintained an initial knee flexion angle of 15°. A compound impulsive test load (compression, flexion moment and internal or external tibial torque) was applied to the distal tibia while recording the 3-D knee loads and tibofemoral kinematics. AM-ACL relative strain was measured using a 3mm DVRT. In this repeated measures experiment, the Wilcoxon Signed-Rank test was used to test the null hypotheses with p<0.05 considered significant. The mean (± SD) peak AM-ACL relative strains were 5.4±3.7 % and 3.1±2.8 % under internal and external tibial torque, respectively. The corresponding mean (± SD) peak AM-ACL strain rates reached 254.4±160.1 %/sec and 179.4±109.9 %/sec, respectively. The hypotheses were supported in that the normalized mean peak AM-ACL relative strain and strain rate were 70% and 42% greater under internal than external tibial torque, respectively (p=0.023, p=0.041). We conclude that internal tibial torque is a potent stressor of the ACL because it induces a considerably (70%) larger peak strain in the AM-ACL than does a corresponding external tibial torque. PMID:22025178

The Effect of Alcohol on Emotional Inertia: A Test of Alcohol Myopia

PubMed Central

Fairbairn, Catharine E.; Sayette, Michael A.

2017-01-01

Alcohol Myopia (AM) has emerged as one of the most widely-researched theories of alcohol’s effects on emotional experience. Given this theory’s popularity it is notable that a central tenet of AM has not been tested—namely, that alcohol creates a myopic focus on the present moment, limiting the extent to which the present is permeated by emotions derived from prior experience. We aimed to test the impact of alcohol on moment-to-moment fluctuations in affect, applying advances in emotion assessment and statistical analysis to test this aspect of AM without drawing the attention of participants to their own emotional experiences. We measured emotional fluctuations using autocorrelation, a statistic borrowed from time-series analysis measuring the correlation between successive observations in time. High emotion autocorrelation is termed “emotional inertia” and linked to negative mood outcomes. Seven-hundred-twenty social drinkers consumed alcohol, placebo, or control beverages in groups of three over a 36-min group formation task. We indexed affect using the Duchenne smile, recorded continuously during the interaction (34.9 million video frames) according to Paul Ekman’s Facial Action Coding System. Autocorrelation of Duchenne smiling emerged as the most consistent predictor of self-reported mood and social bonding when compared with Duchenne smiling mean, standard deviation, and linear trend. Alcohol reduced affective autocorrelation, and autocorrelation mediated the link between alcohol and self-reported mood and social outcomes. Findings suggest that alcohol enhances our ability to freely enjoy the present moment untethered by past experience and highlight the importance of emotion dynamics in research examining affective correlates of psychopathology. PMID:24016015

Quantitative Measurements of Autobiographical Memory Content

PubMed Central

Mainetti, Matteo; Ascoli, Giorgio A.

2012-01-01

Autobiographical memory (AM), subjective recollection of past experiences, is fundamental in everyday life. Nevertheless, characterization of the spontaneous occurrence of AM, as well as of the number and types of recollected details, remains limited. The CRAM (Cue-Recalled Autobiographical Memory) test (http://cramtest.info) adapts and combines the cue-word method with an assessment that collects counts of details recalled from different life periods. The SPAM (Spontaneous Probability of Autobiographical Memories) protocol samples introspection during everyday activity, recording memory duration and frequency. These measures provide detailed, naturalistic accounts of AM content and frequency, quantifying essential dimensions of recollection. AM content (∼20 details/recollection) decreased with the age of the episode, but less drastically than the probability of reporting remote compared to recent memories. AM retrieval was frequent (∼20/hour), each memory lasting ∼30 seconds. Testable hypotheses of the specific content retrieved in a fixed time from given life periods are presented. PMID:23028629

Comparison of level discrimination, increment detection, and comodulation masking release in the audio- and envelope-frequency domains

PubMed Central

Nelson, Paul C.; Ewert, Stephan D.; Carney, Laurel H.; Dau, Torsten

2008-01-01

In general, the temporal structure of stimuli must be considered to account for certain observations made in detection and masking experiments in the audio-frequency domain. Two such phenomena are (1) a heightened sensitivity to amplitude increments with a temporal fringe compared to gated level discrimination performance and (2) lower tone-in-noise detection thresholds using a modulated masker compared to those using an unmodulated masker. In the current study, translations of these two experiments were carried out to test the hypothesis that analogous cues might be used in the envelope-frequency domain. Pure-tone carrier amplitude-modulation (AM) depth-discrimination thresholds were found to be similar using both traditional gated stimuli and using a temporally modulated fringe for a fixed standard depth (ms=0.25) and a range of AM frequencies (4-64 Hz). In a second experiment, masked sinusoidal AM detection thresholds were compared in conditions with and without slow and regular fluctuations imposed on the instantaneous masker AM depth. Release from masking was obtained only for very slow masker fluctuations (less than 2 Hz). A physiologically motivated model that effectively acts as a first-order envelope change detector accounted for several, but not all, of the key aspects of the data. PMID:17471731

"I Am Not a Format": Teachers' Experiences with Fostering Creativity in the Era of Accountability

ERIC Educational Resources Information Center

Olivant, Katie F.

2015-01-01

This phenomenological study examined the experience of fostering creativity and creative thinking in the classroom under high-stakes testing conditions, as described by teachers at a magnet elementary school in Central California. The tensions between standardization and professionalism, as well as performativity and creativity, served as the…

Testing neoclassical competitive market theory in the field.

PubMed

List, John A

2002-11-26

This study presents results from a pilot field experiment that tests predictions of competitive market theory. A major advantage of this particular field experimental design is that my laboratory is the marketplace: subjects are engaged in buying, selling, and trading activities whether I run an exchange experiment or am a passive observer. In this sense, I am gathering data in a natural environment while still maintaining the necessary control to execute a clean comparison between treatments. The main results of the study fall into two categories. First, the competitive model predicts reasonably well in some market treatments: the expected price and quantity levels are approximated in many market rounds. Second, the data suggest that market composition is important: buyer and seller experience levels impact not only the distribution of rents but also the overall level of rents captured. An unexpected result in this regard is that average market efficiency is lowest in markets that match experienced buyers and experienced sellers and highest when experienced buyers engage in bargaining with inexperienced sellers. Together, these results suggest that both market experience and market composition play an important role in the equilibrium discovery process.

The active movement scale: an evaluative tool for infants with obstetrical brachial plexus palsy.

PubMed

Curtis, Christine; Stephens, Derek; Clarke, Howard M; Andrews, David

2002-05-01

Newborns with peripheral nerve lesions involving the upper extremity are difficult to evaluate. The reliability of the Active Movement Scale (AMS), a tool for assessing motor function in infants with obstetrical brachial plexus palsy (OBPP), was examined in 2 complementary studies. Part A was an interrater reliability study in which 63 infants younger than 1 year with OBPP were independently evaluated by 2 physical therapists using the AMS. The scores were compared for reliability and controlled for chance agreement by using kappa statistics. Overall kappa analysis of the 15 tested movements showed a moderate strength of score agreement (kappa = 0.51). Quadratic-weighted kappa (kappa(quad)) statistics showed that 8 of the 15 movements tested were in the highest strength of agreement category (kappa(quad) = 0.81-1.00). Five movements showed substantial agreement (kappa(quad) = 0.61-0.80), and 2 movements had moderate agreement (kappa(quad) = 0.41- 0.60). The overall kappa(quad) was 0.89. Part B was a variability study designed to examine the dispersion of scores when infants with OBPP were evaluated with the AMS by multiple raters. Ten pediatric physical therapists with varying degrees of experience using the scale attended a 1(1/2)-hour instructional workshop on administration of the tool for infants with OBPP. A chain-block study design was used to obtain 30 assessments of 10 infants by 10 raters. A 2-way analysis of variance indicated that the variability of scores due to rater factors was low compared with the variability due to patient factors and that variation in scores due to rater experience was minimal. The results of part A indicate that the AMS is a reliable tool for the assessment of infants with OBPP when raters familiar with the scale are compared. The results of part B suggest that, with minimal training, raters with a range of experience using the AMS are able to reliably evaluate infants with upper-extremity paralysis.

The quest for engaging AmI: Patient engagement and experience design tools to promote effective assisted living.

PubMed

Triberti, Stefano; Barello, Serena

2016-10-01

Recent research highlights that patient engagement, conceived as a patient's behavioral, cognitive and emotional commitment to his own care management, is a key issue while implementing new technologies in the healthcare process. Indeed, eHealth interventions may systematically fail when the patient's subjective experience has not been taken into consideration since the first steps of the technology design. In the present contribution, we argue that such an issue is more and more crucial as regarded to the field of Ambient Intelligence (AmI). Specifically, the exact concept of technologies embedded in the patients' surrounding environment implies a strong impact on their everyday life, which can be perceived as a limitation to autonomy and privacy, and therefore refused or even openly opposed by the final users. The present contribution tackles this issue directly, highlighting: (1) a theoretical framework to include patient engagement in the design of AmI technologies; (2) assessment measures for patient engagement while developing and testing the effectiveness of AmI prototypes for healthcare. Finally (3) this contribution provides an overview of the main issues emerging while implementing AmI technologies and suggests specific design solutions to address them. Copyright © 2016 Elsevier Inc. All rights reserved.

Snaptran2 experiment mounted on dolly being hauled by shielded locomotive ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Snaptran-2 experiment mounted on dolly being hauled by shielded locomotive from IET towards A&M turntable. Note leads from experiment gathered at coupling bar in lower right of view. Another dolly in view at left. Camera facing southeast. Photographer: Page Comiskey. Date: August 25, 1965. INEEL negative no. 65-4503 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. UAH students designed and built the rocket and AM students designed the payload. In this picture, AM students prepare their payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity, prior to launch.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the combined efforts of students from UAH and AM sent this rocket soaring into flight. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Around Marshall

NASA Image and Video Library

2002-05-22

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. UAH students designed and built the rocket and AM students designed the payload. In this picture, AM students prepare their payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity, prior to launch.

Around Marshall

NASA Image and Video Library

2002-05-23

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the combined efforts of students from UAH and AM sent this rocket soaring into flight. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

KSC-2010-4937

NASA Image and Video Library

2010-09-30

CAPE CANAVERAL, Fla. -- High overhead in the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the Alpha Magnetic Spectrometer (AMS) hovers over a rotation stand where it will be tested and processed for launch. AMS, a state-of-the-art particle physics detector, is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch February, 2011. For more information visit: http://www.nasa.gov/mission_pages/shuttle/shuttlemissions/sts134/index.html. Photo credit: NASA/Jack Pfaller

KSC-2010-4938

NASA Image and Video Library

2010-09-30

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, an overhead hoist lowers the Alpha Magnetic Spectrometer (AMS) onto a rotation stand where it will be tested and processed for launch. AMS, a state-of-the-art particle physics detector, is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch February, 2011. For more information visit: http://www.nasa.gov/mission_pages/shuttle/shuttlemissions/sts134/index.html. Photo credit: NASA/Jack Pfaller

KSC-2010-4939

NASA Image and Video Library

2010-09-30

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, technicians guide the Alpha Magnetic Spectrometer (AMS) onto a rotation stand where it will be tested and processed for launch. AMS, a state-of-the-art particle physics detector, is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch February, 2011. For more information visit: http://www.nasa.gov/mission_pages/shuttle/shuttlemissions/sts134/index.html. Photo credit: NASA/Jack Pfaller

Experimente ueber den Einflusse von Metaboliten und Antimetaboliten am Modell von Trichomonas Vaginalis. IX. Mitteilung: Experimente mit Enzymen (Experiments on the Influence of Metabolites and Antimetabolites on the Model of Trichomonas Vaginalis. IX. Communication: Experiments on Enzymes),

DTIC Science & Technology

some enzymes to trichomonas. The following enzymes were used for experiment: pepsin, trypsin, distaste, urease and lysozyme. Tests were performed...obtained in the experiments with urease . Trichomonas growth under addition of lysozyme was within the range of the control cultures. (Modified author abstract)

Effect of axial tibial torque direction on ACL relative strain and strain rate in an in vitro simulated pivot landing.

PubMed

Oh, Youkeun K; Kreinbrink, Jennifer L; Wojtys, Edward M; Ashton-Miller, James A

2012-04-01

Anterior cruciate ligament (ACL) injuries most frequently occur under the large loads associated with a unipedal jump landing involving a cutting or pivoting maneuver. We tested the hypotheses that internal tibial torque would increase the anteromedial (AM) bundle ACL relative strain and strain rate more than would the corresponding external tibial torque under the large impulsive loads associated with such landing maneuvers. Twelve cadaveric female knees [mean (SD) age: 65.0 (10.5) years] were tested. Pretensioned quadriceps, hamstring, and gastrocnemius muscle-tendon unit forces maintained an initial knee flexion angle of 15°. A compound impulsive test load (compression, flexion moment, and internal or external tibial torque) was applied to the distal tibia while recording the 3D knee loads and tibofemoral kinematics. AM-ACL relative strain was measured using a 3 mm DVRT. In this repeated measures experiment, the Wilcoxon signed-rank test was used to test the null hypotheses with p < 0.05 considered significant. The mean (±SD) peak AM-ACL relative strains were 5.4 ± 3.7% and 3.1 ± 2.8% under internal and external tibial torque, respectively. The corresponding mean (± SD) peak AM-ACL strain rates reached 254.4 ± 160.1%/s and 179.4 ± 109.9%/s, respectively. The hypotheses were supported in that the normalized mean peak AM-ACL relative strain and strain rate were 70 and 42% greater under internal than under external tibial torque, respectively (p = 0.023, p = 0.041). We conclude that internal tibial torque is a potent stressor of the ACL because it induces a considerably (70%) larger peak strain in the AM-ACL than does a corresponding external tibial torque. Copyright © 2011 Orthopaedic Research Society.

Small Payload Launch Integrated Testing Services (SPLITS) - SPSDL

NASA Technical Reports Server (NTRS)

Plotner, Benjamin

2013-01-01

My experience working on the Small Payload Launch Integrated Testing Services project has been both educational and rewarding. I have been given the opportunity to work on and experiment with a number of exciting projects and initiatives, each offering different challenges and opportunities for teamwork and collaboration. One of my assignments is to aid in the design and construction of a small-scale two stage rocket as part of a Rocket University initiative. My duties include programming a microcontroller to control the various sensors on the rocket as well as process and transmit data. Additionally, I am writing a graphical user interface application for the ground station that will receive the transmitted data from the rocket and display the information on screen along with a 3D rendering displaying the rocket orientation. Another project I am working on is to design and develop the avionics that will be used to control a high altitude balloon flight that will test a sensor called a Micro Dosimeter that will measure the total ionizing dose absorbed by electrical components during a flight. This includes assembling and soldering the various sensors and components, programming a microcontroller to input and process data from the Micro Dosimeter, and transmitting the data down to a ground station as well as save the data to an on-board SD card. Additionally, I am aiding in the setup and development of ITOS (Integrated Test and Operations System) capability in the SPSDL (Spaceport Processing System Development Lab).

Use of Accelerator Mass Spectrometry in Human Health and Molecular Toxicology.

PubMed

Enright, Heather A; Malfatti, Michael A; Zimmermann, Maike; Ognibene, Ted; Henderson, Paul; Turteltaub, Kenneth W

2016-12-19

Accelerator mass spectrometry (AMS) has been adopted as a powerful bioanalytical method for human studies in the areas of pharmacology and toxicology. The exquisite sensitivity (10 -18 mol) of AMS has facilitated studies of toxins and drugs at environmentally and physiologically relevant concentrations in humans. Such studies include risk assessment of environmental toxicants, drug candidate selection, absolute bioavailability determination, and more recently, assessment of drug-target binding as a biomarker of response to chemotherapy. Combining AMS with complementary capabilities such as high performance liquid chromatography (HPLC) can maximize data within a single experiment and provide additional insight when assessing drugs and toxins, such as metabolic profiling. Recent advances in the AMS technology at Lawrence Livermore National Laboratory have allowed for direct coupling of AMS with complementary capabilities such as HPLC via a liquid sample moving wire interface, offering greater sensitivity compared to that of graphite-based analysis, therefore enabling the use of lower 14 C and chemical doses, which are imperative for clinical testing. The aim of this review is to highlight the recent efforts in human studies using AMS, including technological advancements and discussion of the continued promise of AMS for innovative clinical based research.

The Use of Accelerator Mass Spectrometry in Human Health and Molecular Toxicology

PubMed Central

Enright, Heather A.; Malfatti, Michael A.; Zimmermann, Maike; Ognibene, Ted; Henderson, Paul; Turteltaub, Kenneth W.

2016-01-01

Accelerator Mass Spectrometry (AMS) has been adopted as a powerful bio-analytical method for human studies in the areas of pharmacology and toxicology. The exquisite sensitivity (10−18 mol) of AMS has facilitated studies of toxins and drugs at environmentally and physiologically relevant concentrations in humans. Such studies include: risk assessment of environmental toxicants, drug candidate selection, absolute bioavailability determination, and more recently, assessment of drug-target binding as a biomarker of response to chemotherapy. Combining AMS with complementary capabilities such as high performance liquid chromatography (HPLC) can maximize data within a single experiment and provide additional insight when assessing drugs and toxins, such as metabolic profiling. Recent advances in the AMS technology at Lawrence Livermore National Laboratory have allowed for direct coupling of AMS with complementary capabilities such as HPLC via a liquid sample moving wire interface, offering greater sensitivity compared to graphite-based analysis therefore, enabling the use of lower 14C and chemical doses, which are imperative for clinical testing. The aim of this review is to highlight the recent efforts in human studies using AMS, including technological advancements and discussion of the continued promise of AMS for innovative clinical based research. PMID:27726383

Additive Manufacturing and 3D Printing in NASA: An Overview of Current Projects and Future Initiatives for Space Exploration

NASA Technical Reports Server (NTRS)

Clinton, R. G., Jr.

2014-01-01

NASA, including each Mission Directorate, is investing in, experimenting with, and/or utilizing AM across a broad spectrum of applications and projects; Centers have created and are continuing to create partnerships with industry, other Government Agencies, other Centers, and Universities; In-house additive manufacturing capability enables rapid iteration of the entire design, development and testing process, increasing innovation and reducing risk and cost to projects; For deep space exploration, AM offers significant reduction to logistics costs and risk by providing ability to create on demand; There are challenges: Overwhelming message from recent JANNAF AM for Propulsion Applications TIM was "certification."; NASA will continue to work with our partners to address this and other challenges to advance the state of the art in AM and incorporate these capabilities into an array of applications from aerospace to science missions to deep space exploration.

Qualifying the Sunpower M-87N Cryocooler for Operation in the AMS-02 Magnetic Field

NASA Technical Reports Server (NTRS)

Mustafi, Shuvo; Banks, Stuart; Shirey, Kimberly; Warner, Brent; Leidecker, Henning; Breon, Susan; Boyle, Rob

2003-01-01

The Alpha Magnetic Spectrometer-02 (AMs-02) experiment consists of a superfluid helium dewar. The outer vapor cooled shields of the dewar are to be held at 77 K by four Sunpower M87N cryocoolers. These cryocoolers have magnetic components that might interact with the external applied field generated by the superconducting magnet, thereby degrading the cryocoolers' performance. Engineering models of the Sunpower M87N are being tested at NASA Goddard Space Flight in order to qualify them to operate in a magnetic environment similar to the AMS-02 magnetic environment. AMS-02 will be a space station based particle detector studying the properties and origin of cosmic particles including antimatter and dark matter. It uses a superconducting magnet that is cooled by the superfluid helium dewar. Highly sensitive detector plates inside the magnet will measure a particle's momentum and charge.

Testing neoclassical competitive market theory in the field

PubMed Central

List, John A.

2002-01-01

This study presents results from a pilot field experiment that tests predictions of competitive market theory. A major advantage of this particular field experimental design is that my laboratory is the marketplace: subjects are engaged in buying, selling, and trading activities whether I run an exchange experiment or am a passive observer. In this sense, I am gathering data in a natural environment while still maintaining the necessary control to execute a clean comparison between treatments. The main results of the study fall into two categories. First, the competitive model predicts reasonably well in some market treatments: the expected price and quantity levels are approximated in many market rounds. Second, the data suggest that market composition is important: buyer and seller experience levels impact not only the distribution of rents but also the overall level of rents captured. An unexpected result in this regard is that average market efficiency is lowest in markets that match experienced buyers and experienced sellers and highest when experienced buyers engage in bargaining with inexperienced sellers. Together, these results suggest that both market experience and market composition play an important role in the equilibrium discovery process. PMID:12432103

"Am I carrier?" The patient's lived experience of thrombophilia genetic screening and its outcome.

PubMed

Graffigna, Guendalina; Leone, Daniela; Vegni, Elena

2014-01-01

How do patients with thrombophilia experience a physician's request to undergo a genetic test? How do they experience the test outcome? To answer these questions, we conducted an interpretative phenomenological analysis study, based on 10 in-depth interviews with patients who underwent genetic testing for thrombophilia in Italy, half with positive and half with negative results. The experience of undergoing genetic screening for thrombophilia plays an important role in reconfiguring patients' signification of their illness experience. A positive outcome becomes a cue to reorganize in a more adaptive way the illness meaning at the cognitive and emotive levels, whereas a negative outcome appears more distressing and confusing. As a clinical implication of the study, clinicians should consider communicating carefully with the patients regardless from the positive/negative test results and they should explore the patient's specific reaction and understanding of test result.

Accumulation and release of 241Am by a macrophyte of the Yenisei River (Elodea canadensis).

PubMed

Bolsunovsky, A; Zotina, T; Bondareva, L

2005-01-01

The source of radioactive contamination of the Yenisei River floodplain, including contamination with transuranic elements, is the Mining-and-Chemical Combine of the Russian Ministry of Atomic Energy, which has for many years been producing weapons-grade plutonium. Transuranic elements have been detected not only in the soil and sediment of the river but also in the biomass of aquatic plants. This work is an investigation of accumulation and release of 241Am by a submerged macrophyte of the Yenisei River (Elodea canadensis) in laboratory experiments. In 2000-2003, laboratory experiments were carried out with biomass of E. canadensis Mich. and filtered river water. The samples were collected from the Yenisei River upstream of the discharge of the Combine's radioactive effluent. The experiments showed that 241Am is accumulated by Elodea biomass: the activity concentration of 241Am can reach 3280+/-240 Bq/g, with the concentration factor for 241Am 16 600+/-2200l/kg. Results of chemical fractionation have proved that in the course of 241Am accumulation by Elodea biomass, 241Am tightly bound to biomass increases from 11% to 27% of the total 241Am in the biomass. Release of 241Am from the decaying Elodea biomass has been evaluated experimentally. By the end of the experiment (lasting up to 127 days), the Elodea plants had lost up to 65% of their initial 241Am activity and the rate of 241Am release into the water environment reached 23 Bq/day.

Experimente ueber den Einflusse von Metabolites und Antimetaboliten am Modell von Trichomonas Vaginalis. III. Mitteilung: Experimente mit Essentiellen Fettsaeuren (Experiments on the Influence of Metabolites and Antimetabolites on the Model of Trichomonas Vaginalis. III. Communication: Experiments with Essential Fatty Acids),

DTIC Science & Technology

The relationship between the double and trifold unsaturated fatty acids and Trichomonas vaginalis was tested. The experiments aimed at testing the...influence of vitamin F, linolic and linoleic acid upon multiplication of Trichomonas vaginalis . Vitamin F exerts trichomonacidal effect upon... Trichomonas vaginalis cultures. Linolic acid alone does not yet show great differences at concentrations of 0,01 to 0.05 mg/ml, as compared to the controls. At

[Experimental investigations of 211Am accumulation by macrophytes of the Yenisei River].

PubMed

Bolsunovskiĭ, A Ia; Zotina, T A

2002-01-01

Experiments were carried out in which 241Am was added to water samples containing macrophytes of the Yenisei River, and the radionuclide absorption rates and concentration factors were determined for the plants. It has been shown that the water moss (Fontinalis antipyretica) has a higher capacity to accumulate 241Am than the Canadian pondweed (Elodea canadensis) does. The laboratory experiments revealed that the capacity of dead biomass of the Canadian pondweed to accumulate 241Am is twice higher than that of living biomass. In contrast, no significant increase in 241Am accumulation by dead biomass of the water moss has been recorded. The transuranic element 241Am was firmly fixed by the plant biomass and was not released into water in the course of long-duration experiments.

Improvement of portable computed tomography system for on-field applications

NASA Astrophysics Data System (ADS)

Sukrod, K.; Khoonkamjorn, P.; Tippayakul, C.

2015-05-01

In 2010, Thailand Institute of Nuclear Technology (TINT) received a portable Computed Tomography (CT) system from the IAEA as part of the Regional Cooperative Agreement (RCA) program. This portable CT system has been used as the prototype for development of portable CT system intended for industrial applications since then. This paper discusses the improvements in the attempt to utilize the CT system for on-field applications. The system is foreseen to visualize the amount of agarwood in the live tree trunk. The experiments adopting Am-241 as the radiation source were conducted. The Am-241 source was selected since it emits low energy gamma which should better distinguish small density differences of wood types. Test specimens made of timbers with different densities were prepared and used in the experiments. The cross sectional views of the test specimens were obtained from the CT system using different scanning parameters. It is found from the experiments that the results are promising as the picture can clearly differentiate wood types according to their densities. Also, the optimum scanning parameters were determined from the experiments. The results from this work encourage the research team to advance into the next phase which is to experiment with the real tree on the field.

Skylab

NASA Image and Video Library

1972-03-01

This photograph shows the flight article of the mated Airlock Module (AM) and Multiple Docking Adapter (MDA) being lowering into horizontal position on a transporter. Although the AM and the MDA were separate entities, they were in many respects simply two components of a single module. The AM enabled crew members to conduct extravehicular activities outside Skylab as required for experiment support. Oxygen and nitrogen storage tanks needed for Skylab's life support system were mounted on the external truss work of the AM. Major components in the AM included Skylab's electric power control and distribution station, environmental control system, communication system, and data handling and recording systems. The MDA, forward of the AM, provided docking facilities for the Command and Service Module. It also accommodated several experiment systems, among them the Earth Resource Experiment Package, the materials processing facility, and the control and display console needed for the Apollo Telescope Mount solar astronomy studies. The AM was built by McDornell Douglas and the MDA was built by Martin Marietta. The Marshall Space Flight Center was responsible for the design and development of the Skylab hardware and experiment management.

Feasibility of overnight closed-loop control based on hourly blood glucose measurements.

PubMed

Patte, Caroline; Pleus, Stefan; Galley, Paul; Weinert, Stefan; Haug, Cornelia; Freckmann, Guido

2012-07-01

Safe and effective closed-loop control (artificial pancreas) is the ultimate goal of insulin delivery. In this study, we examined the performance of a closed-loop control algorithm used for the overnight time period to safely achieve a narrow target range of blood glucose (BG) concentrations prior to breakfast. The primary goal was to compare the quality of algorithm control during repeated overnight experiments. Twenty-three subjects with type 1 diabetes performed 2 overnight experiments on each of three visits at the study site, resulting in 138 overnight experiments. On the first evening, the subject's insulin therapy was applied; on the second, the insulin was delivered by an algorithm based on subcutaneous continuous glucose measurements (including meal control) until midnight. Overnight closed-loop control was applied between midnight and 6 a.m. based on hourly venous BG measurements during the first and second nights. The number of BG values within the target range (90-150 mg/dl) increased from 52.9% (219 out of 414 measurements) during the first nights to 72.2% (299 out of 414 measurements) during the second nights (p < .001, χ²-test). The occurrence of hypoglycemia interventions was reduced from 14 oral glucose interventions, the latest occurring at 2:36 a.m. during the first nights, to 1 intervention occurring at 1:02 a.m. during the second nights (p < .001, χ²-test). Overnight controller performance improved when optimized initial control was given; this was suggested by the better metabolic control during the second night. Adequate controller run-in time seems to be important for achieving good overnight control. In addition, the findings demonstrate that hourly BG data are sufficient for the closed-loop control algorithm tested to achieve appropriate glycemic control. © 2012 Diabetes Technology Society.

Use of Accelerator Mass Spectrometry in Human Health and Molecular Toxicology

DOE PAGES

Enright, Heather A.; Malfatti, Michael A.; Zimmermann, Maike; ...

2016-10-11

Accelerator mass spectrometry (AMS) has been adopted as a powerful bioanalytical method for human studies in the areas of pharmacology and toxicology. The exquisite sensitivity (10–18 mol) of AMS has facilitated studies of toxins and drugs at environmentally and physiologically relevant concentrations in humans. Such studies include risk assessment of environmental toxicants, drug candidate selection, absolute bioavailability determination, and more recently, assessment of drug-target binding as a biomarker of response to chemotherapy. Combining AMS with complementary capabilities such as high performance liquid chromatography (HPLC) can maximize data within a single experiment and provide additional insight when assessing drugs and toxins,more » such as metabolic profiling. Recent advances in the AMS technology at Lawrence Livermore National Laboratory have allowed for direct coupling of AMS with complementary capabilities such as HPLC via a liquid sample moving wire interface, offering greater sensitivity compared to that of graphite-based analysis, therefore enabling the use of lower 14C and chemical doses, which are imperative for clinical testing. In conclusion, the aim of this review is to highlight the recent efforts in human studies using AMS, including technological advancements and discussion of the continued promise of AMS for innovative clinical based research.« less

Use of Accelerator Mass Spectrometry in Human Health and Molecular Toxicology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Enright, Heather A.; Malfatti, Michael A.; Zimmermann, Maike

Accelerator mass spectrometry (AMS) has been adopted as a powerful bioanalytical method for human studies in the areas of pharmacology and toxicology. The exquisite sensitivity (10–18 mol) of AMS has facilitated studies of toxins and drugs at environmentally and physiologically relevant concentrations in humans. Such studies include risk assessment of environmental toxicants, drug candidate selection, absolute bioavailability determination, and more recently, assessment of drug-target binding as a biomarker of response to chemotherapy. Combining AMS with complementary capabilities such as high performance liquid chromatography (HPLC) can maximize data within a single experiment and provide additional insight when assessing drugs and toxins,more » such as metabolic profiling. Recent advances in the AMS technology at Lawrence Livermore National Laboratory have allowed for direct coupling of AMS with complementary capabilities such as HPLC via a liquid sample moving wire interface, offering greater sensitivity compared to that of graphite-based analysis, therefore enabling the use of lower 14C and chemical doses, which are imperative for clinical testing. In conclusion, the aim of this review is to highlight the recent efforts in human studies using AMS, including technological advancements and discussion of the continued promise of AMS for innovative clinical based research.« less

A reliability generalization meta-analysis of coefficient alpha and test-retest coefficient for the aging males' symptoms (AMS) scale.

PubMed

Lee, Chin-Pang; Chiu, Yu-Wen; Chu, Chun-Lin; Chen, Yu; Jiang, Kun-Hao; Chen, Jiun-Liang; Chen, Ching-Yen

2016-12-01

The aging males' symptoms (AMS) scale is an instrument used to determine the health-related quality of life in adult and elderly men. The purpose of this study was to synthesize internal consistency (Cronbach's alpha) and test-retest reliability for the AMS scale and its three subscales. Of the 123 studies reviewed, 12 provided alpha coefficients which were then used in the meta-analyses of internal consistency. Seven of the 12 included studies provided test-retest coefficients, and these were used in the meta-analyses of test-retest reliability. The AMS scale had excellent internal consistency [α = 0.89 (95% CI 0.88-0.90)]; the mean alpha estimates across the AMS subscales ranged from 0.79 to 0.82. The AMS scale also had good test-retest reliability [r = 0.85 (95% CI 0.82-0.88]; the test-retest reliability coefficients of the AMS subscales ranged from 0.76 to 0.83. There was significant heterogeneity among the included studies. The AMS scale and the three subscales had fairly good internal consistency and test-retest reliability. Future psychometric studies of the AMS scale should report important characteristics of the participants, details of item scores, and test-retest reliability.

Arbuscular mycorrhizal fungus inoculation reduces the drought-resistance advantage of endophyte-infected versus endophyte-free Leymus chinensis.

PubMed

Liu, Hui; Chen, Wei; Wu, Man; Wu, Rihan; Zhou, Yong; Gao, Yubao; Ren, Anzhi

2017-11-01

Grasses can be infected simultaneously by endophytic fungi and arbuscular mycorrhizal (AM) fungi. In this study, we tested the hypothesis that endophyte-associated drought resistance of a native grass was affected by an AM fungus. In a greenhouse experiment, we compared the performance of endophyte-infected (EI) and endophyte-free (EF) Leymus chinensis, a dominant species native to the Inner Mongolia steppe, under altered water and AM fungus availability. The results showed that endophyte infection significantly increased drought resistance of the host grass, but the beneficial effects were reduced by AM fungus inoculation. In the mycorrhizal-non-inoculated (MF) treatment, EI plants accumulated significantly more biomass, had greater proline and total phenolic concentration, and lower malondialdehyde concentration than EF plants. In the mycorrhizal-inoculation (MI) treatment, however, no significant difference occurred in either growth or physiological characters measured between EI and EF plants. AM fungus inoculation enhanced drought resistance of EF plants but had no significant effect on drought resistance of EI plants, thus AM fungus inoculation reduced the difference between EI and EF plants. Our findings highlight the importance of interactions among multiple microorganisms for plant performance under drought stress.

Mycorrhizal fungal growth responds to soil characteristics, but not host plant identity, during a primary lacustrine dune succession.

PubMed

Sikes, Benjamin A; Maherali, Hafiz; Klironomos, John N

2014-04-01

Soil factors and host plant identity can both affect the growth and functioning of mycorrhizal fungi. Both components change during primary succession, but it is unknown if their relative importance to mycorrhizas also changes. This research tested how soil type and host plant differences among primary successional stages determine the growth and plant effects of arbuscular mycorrhizal (AM) fungal communities. Mycorrhizal fungal community, plant identity, and soil conditions were manipulated among three stages of a lacustrine sand dune successional series in a fully factorial greenhouse experiment. Late succession AM fungi produced more arbuscules and soil hyphae when grown in late succession soils, although the community was from the same narrow phylogenetic group as those in intermediate succession. AM fungal growth did not differ between host species, and plant growth was similarly unaffected by different AM fungal communities. These results indicate that though ecological filtering and/or adaptation of AM fungi occurs during this primary dune succession, it more strongly reflects matching between fungi and soils, rather than interactions between fungi and host plants. Thus, AM fungal performance during this succession may not depend directly on the sequence of plant community succession.

Microstructural Development and Technical Challenges in Laser Additive Manufacturing: Case Study with a 316L Industrial Part

NASA Astrophysics Data System (ADS)

Marya, Manuel; Singh, Virendra; Marya, Surendar; Hascoet, Jean Yves

2015-08-01

Additive manufacturing (AM) brings disruptive changes to the ways parts, and products are designed, fabricated, tested, qualified, inspected, marketed, and sold. These changes introduce novel technical challenges and concerns arising from the maturity and diversity of today's AM processes, feedstock materials, and process parameter interactions. AM bears a resemblance with laser and electron beam welding in the so-called conduction mode, which involves a multitude of dynamic physical events between the projected feedstock and a moving heat source that eventually influence AM part properties. For this paper, an air vent was selected for its thin-walled, hollow, and variable cross section, and limited size. The studied air vents, randomly selected from a qualification batch, were fabricated out of 316L stainless steel using a 4 kW fiber laser powder-fed AM system, referred to as construction laser additive direct (CLAD). These were systematically characterized by microhardness indentation, visual examination, optical and scanning electron microscopy, and electron-back-scattering diffraction in order to determine AM part suitability for service and also broadly discuss metallurgical phenomena. The paper then briefly expands the discussion to include additional engineering alloys and further analyze relationships between AM process parameters and AM part properties, consistently utilizing past experience with the same powder-fed CLAD 3D printer, the well-established science and technology of welding and joining, and recent publications on additive manufacturing.

Actinide Sorption in Rainier Mesa Tunnel Waters from the Nevada Test Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, P; Zavarin, M; Leif, R

2007-12-17

The sorption behavior of americium (Am), plutonium (Pu), neptunium (Np), and uranium (U) in perched Rainier Mesa tunnel water was investigated. Both volcanic zeolitized tuff samples and groundwater samples were collected from Rainier Mesa, Nevada Test Site, NV for a series of batch sorption experiments. Sorption in groundwater with and without the presence of dissolved organic matter (DOM) was investigated. Am(III) and Pu(IV) are more soluble in groundwater that has high concentrations of DOM. The sorption K{sub d} for Am(III) and Pu(IV) on volcanic zeolitized tuff was up to two orders of magnitude lower in samples with high DOM (15more » to 19 mg C/L) compared to samples with DOM removed (< 0.4 mg C/L) or samples with naturally low DOM (0.2 mg C/L). In contrast, Np(V) and U(VI) sorption to zeolitized tuff was much less affected by the presence of DOM. The Np(V) and U(VI) sorption Kds were low under all conditions. Importantly, the DOM was not found to significantly sorb to the zeolitized tuff during these experiment. The concentration of DOM in groundwater affects the transport behavior of actinides in the subsurface. The mobility of Am(III) and Pu(IV) is significantly higher in groundwater with elevated levels of DOM resulting in potentially enhanced transport. To accurately model the transport behavior of actinides in groundwater at Rainier Mesa, the low actinide Kd values measured in groundwater with high DOM concentrations must be incorporated in predictive transport models.« less

Testing Potential Effects of Maize Expressing the Bacillus thuringiensis Cry1Ab Endotoxin (Bt Maize) on Mycorrhizal Fungal Communities via DNA- and RNA-Based Pyrosequencing and Molecular Fingerprinting

PubMed Central

Kuramae, Eiko E.; Hillekens, Remy; de Hollander, Mattias; Kiers, E. Toby; Röling, Wilfred F. M.; Kowalchuk, George A.; van der Heijden, Marcel G. A.

2012-01-01

The cultivation of genetically modified (GM) crops has increased significantly over the last decades. However, concerns have been raised that some GM traits may negatively affect beneficial soil biota, such as arbuscular mycorrhizal fungi (AMF), potentially leading to alterations in soil functioning. Here, we test two maize varieties expressing the Bacillus thuringiensis Cry1Ab endotoxin (Bt maize) for their effects on soil AM fungal communities. We target both fungal DNA and RNA, which is new for AM fungi, and we use two strategies as an inclusive and robust way of detecting community differences: (i) 454 pyrosequencing using general fungal rRNA gene-directed primers and (ii) terminal restriction fragment length polymorphism (T-RFLP) profiling using AM fungus-specific markers. Potential GM-induced effects were compared to the normal natural variation of AM fungal communities across 15 different agricultural fields. AM fungi were found to be abundant in the experiment, accounting for 8% and 21% of total recovered DNA- and RNA-derived fungal sequences, respectively, after 104 days of plant growth. RNA- and DNA-based sequence analyses yielded most of the same AM fungal lineages. Our research yielded three major conclusions. First, no consistent differences were detected between AM fungal communities associated with GM plants and non-GM plants. Second, temporal variation in AMF community composition (between two measured time points) was bigger than GM trait-induced variation. Third, natural variation of AMF communities across 15 agricultural fields in The Netherlands, as well as within-field temporal variation, was much higher than GM-induced variation. In conclusion, we found no indication that Bt maize cultivation poses a risk for AMF. PMID:22885748

Convergent translational evidence of a role for anandamide in amygdala-mediated fear extinction, threat processing and stress-reactivity.

PubMed

Gunduz-Cinar, O; MacPherson, K P; Cinar, R; Gamble-George, J; Sugden, K; Williams, B; Godlewski, G; Ramikie, T S; Gorka, A X; Alapafuja, S O; Nikas, S P; Makriyannis, A; Poulton, R; Patel, S; Hariri, A R; Caspi, A; Moffitt, T E; Kunos, G; Holmes, A

2013-07-01

Endocannabinoids are released 'on-demand' on the basis of physiological need, and can be pharmacologically augmented by inhibiting their catabolic degradation. The endocannabinoid anandamide is degraded by the catabolic enzyme fatty acid amide hydrolase (FAAH). Anandamide is implicated in the mediation of fear behaviors, including fear extinction, suggesting that selectively elevating brain anandamide could modulate plastic changes in fear. Here we first tested this hypothesis with preclinical experiments employing a novel, potent and selective FAAH inhibitor, AM3506 (5-(4-hydroxyphenyl)pentanesulfonyl fluoride). Systemic AM3506 administration before extinction decreased fear during a retrieval test in a mouse model of impaired extinction. AM3506 had no effects on fear in the absence of extinction training, or on various non-fear-related measures. Anandamide levels in the basolateral amygdala were increased by extinction training and augmented by systemic AM3506, whereas application of AM3506 to amygdala slices promoted long-term depression of inhibitory transmission, a form of synaptic plasticity linked to extinction. Further supporting the amygdala as effect-locus, the fear-reducing effects of systemic AM3506 were blocked by intra-amygdala infusion of a CB1 receptor antagonist and were fully recapitulated by intra-amygdala infusion of AM3506. On the basis of these preclinical findings, we hypothesized that variation in the human FAAH gene would predict individual differences in amygdala threat-processing and stress-coping traits. Consistent with this, carriers of a low-expressing FAAH variant (385A allele; rs324420) exhibited quicker habituation of amygdala reactivity to threat, and had lower scores on the personality trait of stress-reactivity. Our findings show that augmenting amygdala anandamide enables extinction-driven reductions in fear in mouse and may promote stress-coping in humans.

Notched-noise precursors improve detection of low-frequency amplitude modulationa)

PubMed Central

Almishaal, Ali; Bidelman, Gavin M.; Jennings, Skyler G.

2017-01-01

Amplitude modulation (AM) detection was measured with a short (50 ms), high-frequency carrier as a function of carrier level (Experiment I) and modulation frequency (Experiment II) for conditions with or without a notched-noise precursor. A longer carrier (500 ms) was also included in Experiment I. When the carrier was preceded by silence (no precursor condition) AM detection thresholds worsened for moderate-level carriers compared to lower- or higher-level carriers, resulting in a “mid-level hump.” AM detection thresholds with a precursor were better than those without a precursor, primarily for moderate-to-high level carriers, thus eliminating the mid-level hump in AM detection. When the carrier was 500 ms, AM thresholds improved by a constant (across all levels) relative to AM thresholds with a precursor, consistent with the longer carrier providing more “looks” to detect the AM signal. Experiment II revealed that improved AM detection with compared to without a precursor is limited to low-modulation frequencies (<60 Hz). These results are consistent with (1) a reduction in cochlear gain over the course of the precursor perhaps via the medial olivocochlear reflex or (2) a form of perceptual enhancement which may be mediated by adaptation of inhibition. PMID:28147582

An empirical investigation of the possibility of adaptability of arbuscular mycorrhizal fungi to new hosts.

PubMed

Koyama, Akihiro; Pietrangelo, Olivia; Sanderson, Laura; Antunes, Pedro M

2017-08-01

Little is known about the adaptive capacity of arbuscular mycorrhizal (AM) fungi to novel hosts. Here we assessed the possibility of two heterospecific AM fungal isolates to adaptively change, in terms of host biomass response, as a function of host plant identity, over the course of a growing season. First, we produced pure inocula of Rhizophagus clarus and Rhizophagus intraradices, each starting from a single spore. Second, we "trained" each isolate individually in a community with two plants, sudangrass (Sorgum bicolour subsp. drummondii) and leek (Aliium ampeloprasum var. porrum), using a dual-compartment system to allow the establishment of a common mycorrhizal network between the two hosts. Third, we conducted a greenhouse experiment to reciprocally test each "trained" clone, obtained from each compartment, either with the same (home), or the other host (away) under two contrasting phosphorus levels. Overall, results did not support adaptive responses of the AM fungi to their hosts (i.e., greater host biomass under "home" relative to "away" conditions), but the opposite (i.e., greater host biomass under "away" relative to "home" conditions) was more frequently observed. These changes in AM fungal symbiotic functioning open the possibility for relatively rapid genetic change of arbuscular mycorrhizal fungi in response to new hosts, which represents one step forward from in vitro experiments.

Materialism and Mortality: Slavic-American Immigrant and Education, 1890-1940

ERIC Educational Resources Information Center

Bodnar, John

1976-01-01

Suggests that a concensus does not exist among immigrants in the worshipping of American schools and their potentiality. By focusing on Slavic-Americans, the essay tests the hypothesis that the American experience of southern and eastern Europeans intensified the concern for learning. (Author/AM)

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, a student from AM and his mentor install their payload into the launch vehicle which was built by the team of UAH students. The scientific payload, developed and built by the team of AM students, measured the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Around Marshall

NASA Image and Video Library

2002-05-22

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, a student from AM and his mentor install their payload into the launch vehicle which was built by the team of UAH students. The scientific payload, developed and built by the team of AM students, measured the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Knowledge of community pharmacists about antibiotics, and their perceptions and practices regarding antimicrobial stewardship: a cross-sectional study in Punjab, Pakistan

PubMed Central

Sarwar, Muhammad Rehan; Saqib, Anum; Iftikhar, Sadia; Sadiq, Tayyaba

2018-01-01

Objective To evaluate the knowledge of community pharmacists about antibiotics, and their perceptions and practices toward antimicrobial stewardship (AMS) in Punjab, Pakistan. Materials and methods A descriptive cross-sectional study was conducted among community pharmacists in Punjab, Pakistan from April 1, 2017 to May 31, 2017. A self-administered and pretested questionnaire was used for data collection. A simple random-sampling method was used to select community pharmacies. Independent-sample Mann–Whitney U tests, independent sample Kruskal–Wallis tests, and logistic regression analysis were performed with SPSS version 21.0. Results Of the 414 pharmacists, 400 responded to the survey (response rate 96.6%). The participants had good knowledge about antibiotics. They showed positive perceptions, but poor practices regarding AMS. All of the participants were of the view that AMS program could be beneficial for health care professionals for improvement of patient care, and 78% (n=312) of participants gave their opinion about incorporation of AMS programs in community pharmacies. Collaboration was never/rarely undertaken by pharmacists with other health care professionals over the use of antibiotics (n=311, 77.8%), and a significant proportion of participants (n=351, 87.8%) never/rarely participated in AMS-awareness campaigns. Logistic regression analysis revealed that male sex (OR 0.204, 95% CI 0.104−0.4; P<0.001), age 20–29 years (OR 0.172, 95% CI 0.05−0.595; P=0.005), and <1 year of experience (OR 0.197, 95% CI 0.083−0.468; P<0.001) were the factors associated with poor practices regarding AMS. Conclusion Pharmacists had good knowledge about antibiotics. There were some gaps in perceptions and practices of community pharmacists regarding AMS. In the current scenario, it will be critical to fill these gaps and improve perceptions and practices of community pharmacists regarding AMS by developing customized interventions. PMID:29403295

Amplitude modulation of sexy phrases is salient for song attractiveness in female canaries (Serinus canaria).

PubMed

Pasteau, Magali; Ung, Davy; Kreutzer, Michel; Aubin, Thierry

2012-07-01

Song discrimination and recognition in songbird species have usually been studied by measuring responses to song playbacks. In female canaries, Serinus canaria, copulation solicitation displays (CSDs) are used as an index of female preferences, which are related to song recognition. Despite the fact that many studies underline the role of song syntax in this species, we observed that short segments of songs (a few seconds long) are enough for females to discriminate between conspecific and heterospecific songs, whereas such a short duration is not sufficient to identify the syntax rules. This suggests that other cues are salient for song recognition. In this experiment, we investigated the influence of amplitude modulation (AM) on the responses (CSDs) of female canaries to song playbacks. We used two groups of females: (1) raised in acoustic isolation and (2) raised in normal conditions. When adult, we tested their preferences for sexy phrases with different AMs. We broadcast three types of stimuli: (1) songs with natural canary AM, (2) songs with AM removed, or (3) song with wren Troglodytes troglodytes AM. Results indicate that female canaries prefer and have predispositions for a song type with the natural canary AM. Thus, this acoustic parameter is a salient cue for song attractiveness.

High Purity Americium-241 for Fuel Cycle R&D Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. Paul A. Lessing

2011-07-01

Previously the U.S. Department of Energy released Am-241 for various applications such as smoke detectors and Am-Be neutron sources for oil wells. At this date there is a shortage of usable, higher purity Am-241 in metal and oxide form available in the United States. Recently, the limited source of Am-241 has been from Russia with production being contracted to existing customers. The shortage has resulted in the price per gram rising dramatically over the last few years. DOE-NE currently has need for high purity Am-241 metal and oxide to fabricate fuel pellets for reactor testing in the Fuel Cycle R&Dmore » program. All the available high purity americium has been gathered from within the DOE system of laboratories. However, this is only a fraction of the projected needs of FCRD over the next 10 years. Therefore, FCR&D has proposed extraction and purification concepts to extract Am-241 from a mixed AmO2-PuO2 feedstock stored at the Savannah River Site. The most simple extraction system is based upon high temperature reduction using lanthanum metal with concurrent evaporation and condensation to produce high purity Am metal. Metallic americium has over a four order of magnitude higher vapor pressure than plutonium. Results from small-scale reduction experiments are presented. These results confirm thermodynamic predictions that at 1000 deg C metallic lanthanum reduces both PuO2 and AmO2. Faster kinetics are expected for temperatures up to about 1500 deg C.« less

Changes in antimicrobial prescribing behavior after the introduction of the antimicrobial stewardship program: A pre- and post-intervention survey.

PubMed

Chavada, Ruchir; Walker, Harry N; Tong, Deborah; Murray, Amy

2017-10-02

The introduction of an antimicrobial stewardship (AMS) program is associated with a change in antimicrobial prescribing behavior. A proposed mechanism for this change is by impacting the prescribing etiquette described in qualitative studies. This study sought to detect a change in prescribing attitudes 12 months after the introduction of AMS and gauge utility of various AMS interventions. Surveys were distributed to doctors in two regional Australian hospitals on a convenience basis 6 months before, and 12 months after, the introduction of AMS. Agreement with 20 statements describing attitudes (cultural, behavioral and knowledge) towards antimicrobial prescribing was assessed on a 4-point Likert scale. Mean response scores were compared using the Wilcoxon Rank sum test. 155 responses were collected before the introduction of AMS, and 144 afterwards. After the introduction of AMS, an increase was observed in knowledge about available resources such as electronic decision support systems (EDSS) and therapeutic guidelines, with raised awareness about the support available through AMS rounds and the process to be followed when prescribing restricted antimicrobials. Additionally, doctors were less likely to rely on pharmacy to ascertain when an antimicrobial was restricted, depend on infectious diseases consultant advice and use past experience to guide antimicrobial prescribing. Responses to this survey indicate that positive changes to the antimicrobial prescribing etiquette may be achieved with the introduction of an AMS program. Use of EDSS and other resources such as evidence-based guidelines are perceived to be important to drive rational antimicrobial prescribing within AMS programs.

Antidepressant-like effects of the cannabinoid receptor ligands in the forced swimming test in mice: mechanism of action and possible interactions with cholinergic system.

PubMed

Kruk-Slomka, Marta; Michalak, Agnieszka; Biala, Grazyna

2015-05-01

The purpose of the experiments was to explore the role of the endocannabinoid system, through cannabinoid (CB) receptor ligands, nicotine and scopolamine, in the depression-related responses using the forced swimming test (FST) in mice. Our results revealed that acute injection of oleamide (10 and 20 mg/kg), a CB1 receptor agonist, caused antidepressant-like effect in the FST, while AM 251 (0.25-3 mg/kg), a CB1 receptor antagonist, did not provoke any effect in this test. Moreover, acute administration of both CB2 receptor agonist, JWH 133 (0.5 and 1 mg/kg) and CB2 receptor antagonist, AM 630 (0.5 mg/kg), exhibited antidepressant action. Antidepressant effects of oleamide and JWH 133 were attenuated by acute injection of both non-effective dose of AM 251, as well as AM 630. Among the all CB compounds used, only the combination of non-effective dose of oleamide (2.5 mg/kg) with non-effective dose of nicotine (0.5 mg/kg) caused an antidepressant effect. However, none of the CB receptor ligands, had influence on the antidepressant effects provoked by nicotine (0.2 mg/kg) injection. In turn, the combination of non-effective dose of oleamide (2.5 mg/kg); JWH (2 mg/kg) or AM 630 (2 mg/kg), but not of AM 251 (0.25 mg/kg), with non-effective dose of scopolamine (0.1 mg/kg), exhibited antidepressant properties. Indeed, all of the CB compounds used, intensified the antidepressant-like effects induced by an acute injection of scopolamine (0.3 mg/kg). Our results provide clear evidence that the endocannabinoid system participates in the depression-related behavior and through interactions with cholinergic system modulate these kind of responses. Copyright © 2015 Elsevier B.V. All rights reserved.

Compost Addition Enhanced Hyphal Growth and Sporulation of Arbuscular Mycorrhizal Fungi without Affecting Their Community Composition in the Soil

PubMed Central

Yang, Wei; Gu, Siyu; Xin, Ying; Bello, Ayodeji; Sun, Wenpeng; Xu, Xiuhong

2018-01-01

Arbuscular mycorrhizal (AM) fungi form symbiotic associations with most crop plant species in agricultural ecosystems, and are conspicuously influenced by various agricultural practices. To understand the impact of compost addition on AM fungi, we examined effect of four compost rates (0, 11.25, 22.5, and 45 Mg/ha) on the abundance and community composition of AM fungi in seedling, flowering, and mature stage of soybean in a 1-year compost addition experiment system in Northeast China. Soybean [Glycine max (L.) Merrill] was used as test plant. Moderate (22.5 Mg/ha) and high (45 Mg/ha) levels of compost addition significantly increased AM root colonization and extraradical hyphal (ERH) density compared with control, whereas low (11.5 Mg/ha) level of compost addition did not cause significant increase in AM root colonization and ERH density. AM fungal spore density was significantly enhanced by all the compost rates compared with control. The temporal variations analysis revealed that, AM root colonization in seedling stage was significantly lower than in flowering and mature stage. Although AM fungal operational taxonomic unit richness and community composition was unaffected by compost addition, some abundant AM fungal species showed significantly different response to compost addition. In mature stage, Rhizophagus fasciculatum showed increasing trend along with compost addition gradient, whereas the opposite was observed with Paraglomus sp. In addition, AM fungal community composition exhibited significant temporal variation during growing season. Further analysis indicated that the temporal variation in AM fungal community only occurred in control treatment, but not in low, moderate, and high level of compost addition treatments. Our findings highlighted the significant effects of compost addition on AM growth and sporulation, and emphasized that growth stage is a stronger determinant than 1-year compost addition in shaping AM fungal community in black soil of Northeast China. PMID:29467752

Compost Addition Enhanced Hyphal Growth and Sporulation of Arbuscular Mycorrhizal Fungi without Affecting Their Community Composition in the Soil.

PubMed

Yang, Wei; Gu, Siyu; Xin, Ying; Bello, Ayodeji; Sun, Wenpeng; Xu, Xiuhong

2018-01-01

Arbuscular mycorrhizal (AM) fungi form symbiotic associations with most crop plant species in agricultural ecosystems, and are conspicuously influenced by various agricultural practices. To understand the impact of compost addition on AM fungi, we examined effect of four compost rates (0, 11.25, 22.5, and 45 Mg/ha) on the abundance and community composition of AM fungi in seedling, flowering, and mature stage of soybean in a 1-year compost addition experiment system in Northeast China. Soybean [ Glycine max (L.) Merrill] was used as test plant. Moderate (22.5 Mg/ha) and high (45 Mg/ha) levels of compost addition significantly increased AM root colonization and extraradical hyphal (ERH) density compared with control, whereas low (11.5 Mg/ha) level of compost addition did not cause significant increase in AM root colonization and ERH density. AM fungal spore density was significantly enhanced by all the compost rates compared with control. The temporal variations analysis revealed that, AM root colonization in seedling stage was significantly lower than in flowering and mature stage. Although AM fungal operational taxonomic unit richness and community composition was unaffected by compost addition, some abundant AM fungal species showed significantly different response to compost addition. In mature stage, Rhizophagus fasciculatum showed increasing trend along with compost addition gradient, whereas the opposite was observed with Paraglomus sp. In addition, AM fungal community composition exhibited significant temporal variation during growing season. Further analysis indicated that the temporal variation in AM fungal community only occurred in control treatment, but not in low, moderate, and high level of compost addition treatments. Our findings highlighted the significant effects of compost addition on AM growth and sporulation, and emphasized that growth stage is a stronger determinant than 1-year compost addition in shaping AM fungal community in black soil of Northeast China.

Use of stoichiometry to predict the abundance and functioning of root symbioses

NASA Astrophysics Data System (ADS)

Johnson, N. C.

2012-04-01

Plants form nutritional symbioses with fungi and bacteria and the importance of these partnerships varies with the mineral fertility of soil. There is strong evidence that plants acclimate and adapt to their local soil conditions through root symbioses; nitrogen limitation is ameliorated by symbiosis with diazotrophic prokaryotes and mycorrhizas ameliorate phosphorus limitation. Corollaries of ecological stoichiometry may be useful for predicting the abundance and functioning of mycorrhizas and N-fixation symbioses. A series of field experiments show that arbuscular mycorrhizal (AM) symbioses in grasslands in North America and in the African Serengeti are most beneficial to plant nutrition when plants are phosphorus limited and have sufficient nitrogen and carbon. A reciprocal inoculation experiment shows that locally adapted communities of AM fungi, associated soil organisms and plants arise such that mutualistic benefits are maximized; both AM fungi and plants grew best in their "home" soil-symbiont combination compared to "away" soil-symbiont combinations. Plants in their home combination acquired more limiting resource (either phosphorus or nitrogen) and consequently grew larger; similarly, AM fungi in their home combination formed more arbuscules and extraradical hyphae. Genetic analysis of the AM fungi inside plant roots indicate that these results correspond to variation in the community composition of AM fungi and also to variation in the symbiotic performance of local isolates of one particular species of AM fungus. The next step is to conduct landscape scale studies of root symbioses to test the hypothesis that plants cultivate microbial communities in and around their roots such that the species and ecotypes of microorganisms within these communities is customized for optimal nutrient acquisition under site-specific environmental conditions. If locally adapted communities of root and rhizosphere organisms are common, then plants may be optimizing their foraging by fostering microbial partnerships which compensate for unfavorable resource stoichiometry. This finding would suggest that the communities of microorganisms associated with plant roots are somewhat analogous to the communities of microorganisms that animals cultivate in their gut.

Neutron capture and neutron-induced fission experiments on americium isotopes with DANCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jandel, M.; Bredeweg, T. A.; Fowler, M. M.

2009-01-28

Neutron capture cross section data on Am isotopes were measured using the Detector for Advanced Neutron Capture Experiments (DANCE) at Los Alamos National Laboratory. The neutron capture cross section was determined for {sup 241}Am for neutron energies between thermal and 320 keV. Preliminary results were also obtained for {sup 243}Am for neutron energies between 10 eV and 250 keV. The results on concurrent neutron-induced fission and neutron-capture measurements on {sup 242m}Am will be presented where the fission events were actively triggered during the experiments. In these experiments, a Parallel-Plate Avalanche Counter (PPAC) detector that surrounds the target located in themore » center of the DANCE array was used as a fission-tagging detector to separate (n,{gamma}) events from (n,f) events. The first direct observation of neutron capture on {sup 242m}Am in the resonance region in between 2 and 9 eV of the neutron energy was obtained.« less

Neutron capture and neutron-induced fission experiments on americium isotopes with DANCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jandel, Marian

2008-01-01

Neutron capture cross section data on Am isotopes were measured using the Detector for Advanced Neutron Capture Experiments (DANCE) at Los Alamos National Laboratory. The neutron capture cross section was determined for {sup 241}Am for neutron energies between thermal and 320 keV. Preliminary results were also obtained for {sup 243}Am for neutron energies between 35 eV and 200 keV. The results on concurrent neutron-induced fission and neutron-capture measurements on {sup 242m}Am will be presented, where the fission events were actively triggered during the experiments. In these experiments, the Parallel-Plate Avalanche Counter (PPAC) detector that surrounds the target located in themore » center of the DANCE array was used as a fission-tagging detector to separate (n,{gamma}) from (n,f) events. The first evidence of neutron capture on {sup 242m}Am in the resonance region in between 2 and 9 eV of the neutron energy was obtained.« less

Laboratory investigation of the role of desorption kinetics on americium transport associated with bentonite colloids.

PubMed

Dittrich, Timothy Mark; Boukhalfa, Hakim; Ware, Stuart Douglas; Reimus, Paul William

2015-10-01

Understanding the parameters that control colloid-mediated transport of radionuclides is important for the safe disposal of used nuclear fuel. We report an experimental and reactive transport modeling examination of americium transport in a groundwater-bentonite-fracture fill material system. A series of batch sorption and column transport experiments were conducted to determine the role of desorption kinetics from bentonite colloids in the transport of americium through fracture materials. We used fracture fill material from a shear zone in altered granodiorite collected from the Grimsel Test Site (GTS) in Switzerland and colloidal suspensions generated from FEBEX bentonite, a potential repository backfill material. The colloidal suspension (100 mg L(-1)) was prepared in synthetic groundwater that matched the natural water chemistry at GTS and was spiked with 5.5 × 10(-10) M (241)Am. Batch characterizations indicated that 97% of the americium in the stock suspension was adsorbed to the colloids. Breakthrough experiments conducted by injecting the americium colloidal suspension through three identical columns in series, each with mean residence times of 6 h, show that more than 95% of the bentonite colloids were transported through each of the columns, with modeled colloid filtration rates (k(f)) of 0.01-0.02 h(-1). Am recoveries in each column were 55-60%, and Am desorption rate constants from the colloids, determined from 1-D transport modeling, were 0.96, 0.98, and 0.91 h(-1) in the three columns, respectively. The consistency in Am recoveries and desorption rate constants in each column indicates that the Am was not associated with binding sites of widely-varying strengths on the colloids, as one binding site with fast kinetics represented the system accurately for all three sequential columns. Our data suggest that colloid-mediated transport of Am in a bentonite-fracture fill material system is unlikely to result in transport over long distance scales because of the ability of the fracture materials to rapidly strip Am from the bentonite colloids and the apparent lack of a strong binding site that would keep a fraction of the Am strongly-associated with the colloids. Published by Elsevier Ltd.

Welding of AM350 and AM355 steel

NASA Technical Reports Server (NTRS)

Davis, R. J.; Wroth, R. S.

1967-01-01

A series of tests was conducted to establish optimum procedures for TIG welding and heat treating of AM350 and AM355 steel sheet in thicknesses ranging from 0.010 inch to 0.125 inch. Statistical analysis of the test data was performed to determine the anticipated minimum strength of the welded joints.

Diurnal effects of prior heat stress exposure on sprint and endurance exercise capacity in the heat.

PubMed

Otani, Hidenori; Kaya, Mitsuharu; Tamaki, Akira; Goto, Heita; Goto, Takayuki; Shirato, Minayuki

2018-03-21

Active individuals often perform exercises in the heat following heat stress exposure (HSE) regardless of the time-of-day and its variation in body temperature. However, there is no information concerning the diurnal effects of a rise in body temperature after HSE on subsequent exercise performance in a hot environnment. This study therefore investigated the diurnal effects of prior HSE on both sprint and endurance exercise capacity in the heat. Eight male volunteers completed four trials which included sprint and endurance cycling tests at 30 °C and 50% relative humidity. At first, volunteers completed a 30-min pre-exercise routine (30-PR): a seated rest in a temperate environment in AM (AmR) or PM (PmR) (Rest trials); and a warm water immersion at 40 °C to induce a 1 °C increase in core temperature in AM (AmW) or PM (PmW) (HSE trials). Volunteers subsequently commenced exercise at 0800 h in AmR/AmW and at 1700 h in PmR/PmW. The sprint test determined a 10-sec maximal sprint power at 5 kp. Then, the endurance test was conducted to measure time to exhaustion at 60% peak oxygen uptake. Maximal sprint power was similar between trials (p = 0.787). Time to exhaustion in AmW (mean±SD; 15 ± 8 min) was less than AmR (38 ± 16 min; p < 0.01) and PmR (43 ± 24 min; p < 0.01) but similar with PmW (24 ± 9 min). Core temperature was higher from post 30-PR to 6 min into the endurance test in AmW and PmW than AmR and PmR (p < 0.05) and at post 30-PR and the start of the endurance test in PmR than AmR (p < 0.05). The rate of rise in core temperature during the endurance test was greater in AmR than AmW and PmW (p < 0.05). Mean skin temperature was higher from post 30-PR to 6 min into the endurance test in HSE trials than Rest trials (p < 0.05). Mean body temperature was higher from post 30-PR to 6 min into the endurance test in AmW and PmW than AmR and PmR (p < 0.05) and the start to 6 min into the endurance test in PmR than AmR (p < 0.05). Convective, radiant, dry and evaporative heat losses were greater on HSE trials than on Rest trials (p < 0.001). Heart rate and cutaneous vascular conductance were higher at post 30-PR in HSE trials than Rest trials (p < 0.05). Thermal sensation was higher from post 30-PR to the start of the endurance test in AmW and PmW than AmR and PmR (p < 0.05). Perceived exertion from the start to 6 min into the endurance test was higher in HSE trials than Rest trials (p < 0.05). This study demonstrates that an approximately 1 °C increase in core temperature by prior HSE has the diurnal effects on endurance exercise capacity but not on sprint exercise capacity in the heat. Moreover, prior HSE reduces endurance exercise capacity in AM, but not in PM. This reduction is associated with a large difference in pre-exercise core temperature between AM trials which is caused by a relatively lower body temperature in the morning due to the time-of-day variation and contributes to lengthening the attainment of high core temperature during exercise in AmR.

A Narrative Analysis of Educators' Lived Experiences of Motherhood and Teaching

ERIC Educational Resources Information Center

Knowles, Mariska; Nieuwenhuis, Jan; Smit, Brigitte

2009-01-01

In this article we argue that mothers often construct images of what they perceive as society's expectations of them. These images become the parameters in the eyes of society to which they aspire. This is reminiscent of the adage: "I am not who you think I am. I am not who I think I am. I am who I think you think I am". This study is…

Chemical/Biological Agent Resistance Test (CBART) Test Fixture System Verification and Analytical Monitioring System Development

DTIC Science & Technology

2011-03-15

Lone Eagle Street Columbus Ohio 43228 Installation trades personnel 5/7/2009 12:00:00AM 10/31/2010 12:00:00AM Sub Contractor Numbers (c): Patent...43026-2573 Pipe fitter installation trades personnel. 10/21/2009 12:00:00AM 1/31/2011 12:00:00AM Sub Contractor Numbers (c): Patent Clause Number...City Electric Company 1099 Sullivant Avenue Columbus Ohio 43223 Electrical installation trades personnel 4/5/2009 12:00:00AM 9/30/2010 12:00:00AM

The impact of scopolamine pretreatment on 3-iodothyronamine (T1AM) effects on memory and pain in mice.

PubMed

Laurino, Annunziatina; Lucenteforte, Ersilia; De Siena, Gaetano; Raimondi, Laura

2017-08-01

We previously demonstrated that 3-iodothyronamine (T1AM), a by-product of thyroid hormone metabolism, pharmacologically administered to mice acutely stimulated learning and memory acquisition and provided hyperalgesia with a mechanism which remains to be defined. We now aimed to investigate whether the T1AM effect on memory and pain was maintained in mice pre-treated with scopolamine, a non-selective muscarinic antagonist expected to induce amnesia and, possibly, hyperalgesia. Mice were pre-treated with scopolamine and, after 20min, injected intracerebroventricularly (i.c.v.) with T1AM (0.13, 0.4, 1.32μg/kg). 15min after T1AM injection, the mice learning capacity or their pain threshold were evaluated by the light/dark box and by the hot plate test (51.5°C) respectively. Experiments in the light/dark box were repeated in mice receiving clorgyline (2.5mg/kg, i.p.), a monoamine oxidase (MAO) inhibitor administered 10min before scopolamine (0.3mg/kg). Our results demonstrated that 0.3mg/kg scopolamine induced amnesia without modifying the murine pain threshold. T1AM fully reversed scopolamine-induced amnesia and produced hyperalgesia at a dose as low as 0.13μg/kg. The T1AM anti-amnestic effect was lost in mice pre-treated with clorgyline. We report that the removal of muscarinic signalling increases T1AM pro learning and hyperalgesic effectiveness suggesting T1AM as a potential treatment as a "pro-drug" for memory dysfunction in neurodegenerative diseases. Copyright © 2017 Elsevier Inc. All rights reserved.

Experimente ueber den Einflusse von Metaboliten und Antimetaboliten am Modell von Trichomonas Vaginalis. VIII. Mitteilung: Experiments mit Hormonen (Experiments on the Influence of Metabolites and Antimetabolites on the Model of Trichomonas Vaginalis. VIII. Communication: Experiments with Hormones),

DTIC Science & Technology

experiments were performed on 7 trichomonas vaginalis strains. The test cultures with serotonin, oestron, testosteron and methyltestosteron grew at...The present study has been concerned with the influence of some hormones upon trichomonas growth. The following substances were used for our...ml onward. Adrenalin and noradrenalin have generally inhibiting action (from 0.80 mg/ml onward) upon trichomonas growth. The antihormone 3.5-dijodtyrosin does rarely influence the growth of trichomonas . (Author)

CSI feedback-based CS for underwater acoustic adaptive modulation OFDM system with channel prediction

NASA Astrophysics Data System (ADS)

Kuai, Xiao-yan; Sun, Hai-xin; Qi, Jie; Cheng, En; Xu, Xiao-ka; Guo, Yu-hui; Chen, You-gan

2014-06-01

In this paper, we investigate the performance of adaptive modulation (AM) orthogonal frequency division multiplexing (OFDM) system in underwater acoustic (UWA) communications. The aim is to solve the problem of large feedback overhead for channel state information (CSI) in every subcarrier. A novel CSI feedback scheme is proposed based on the theory of compressed sensing (CS). We propose a feedback from the receiver that only feedback the sparse channel parameters. Additionally, prediction of the channel state is proposed every several symbols to realize the AM in practice. We describe a linear channel prediction algorithm which is used in adaptive transmission. This system has been tested in the real underwater acoustic channel. The linear channel prediction makes the AM transmission techniques more feasible for acoustic channel communications. The simulation and experiment show that significant improvements can be obtained both in bit error rate (BER) and throughput in the AM scheme compared with the fixed Quadrature Phase Shift Keying (QPSK) modulation scheme. Moreover, the performance with standard CS outperforms the Discrete Cosine Transform (DCT) method.

The efficacies of pure LICAM(C) and DTPA on the retention of plutonium-238 and americium-241 in rats after their inhalation as nitrate and intravenous injection as citrate.

PubMed

Stradling, G N; Stather, J W; Gray, S A; Moody, J C; Ellender, M; Hodgson, A; Volf, V; Taylor, D M; Wirth, P; Gaskin, P W

1989-10-01

The pure carboxylated catechoyl amide LICAM(C) and the calcium and zinc salts of diethylenetriaminepenta-acetic acid (DTPA), were tested for efficacy for removing 238Pu and 241Am from rats after inhalation of the nitrate or intravenous injection of the citrate. The results were compared with the efficacy of methylated LICAM(C) used in previous experiments. It was shown that: (1) after inhalation of 238Pu nitrate, DTPA was far superior to pure LICAM(C); (2) after intravenous injection of 238Pu citrate, the infusion of DTPA plus LICAM(C) was only marginally more effective than DTPA alone; and (3) after inhalation or intravenous injection of 238Pu plus 241Am, the efficacy of pure LICAM(C) was only marginally more effective than the methylated form and neither form was effective for the decorporation of 241Am. It was concluded that DTPA, at present, remains the chelating agent of choice for treating persons accidentally contaminated with transportable forms of Pu and Am.

Ectopic Integration of Transforming DNA Is Rare among Neurospora Transformants Selected for Gene Replacement

PubMed Central

Miao, VPW.; Rountree, M. R.; Selker, E. U.

1995-01-01

In a variety of organisms, DNA-mediated transformation experiments commonly produce transformants with multiple copies of the transforming DNA, including both selected and unselected molecules. Such ``cotransformants'' are much more common than expected from the individual transformation frequencies, suggesting that subpopulations of cells, or nuclei, are particularly competent for transformation. We found that Neurospora crassa transformants selected for gene replacement at the am gene had not efficiently incorporated additional DNA, suggesting that nuclei that undergo transformation by homologous recombination are not highly competent at integration of DNA by illegitimate recombination. Spheroplasts were treated with DNA fragments homologous to am and with an Escherichia coli hph plasmid. Transformants were initially selected for hph (hygromycin(R)), allowed to conidiate to generate homokaryons and then selected for either Am(-) (gene replacements) or hph. Surprisingly, most am replacement strains were hygromycin(S) (124/140) and carried no extraneous DNA (116/140). Most transformants selected for hph also had ectopic copies of am DNA and/or multiple copies of hph sequences (32/35), generally at multiple sites, confirming that efficient cotransformation could occur. To test the implication that cotransformation involving gene replacement and ectopic integration is rare, we compared the yields of am replacement strains with or without prior selection for hph. The initial selection did not appreciably help (or hinder) recovery of strains with replacements. PMID:7789758

Assessment of 14C AMS dating of phytoliths as a new paleoenvironmental and archaeological tool

NASA Astrophysics Data System (ADS)

Corbineau, R.; Alexandre, A. E.; Santos, G. M.; Reyerson, P. E.

2011-12-01

14C AMS analysis of occluded carbon in phytoliths (phytC) is a promising dating tool for palaeoenvironmental and archaeological studies. In order to assess the accuracy of this method, different tests were recently carried out on large phytolith concentrates of phytC samples extracted from soils and harvested plants, in association with blank samples of SiO2 powder to check the absence of carbon contamination during the treatments. Despite this precaution, 14C values from recent harvested plants were inexplicably old (2 - 8 ka years BP). Nevertheless, we noticed that many chemical extraction protocols that were used did not lead to samples totally free of organic matter. In order to tackle this problem, and as a first step, the efficiency of common extraction protocols from the literature were tested. Samples were analyzed by SEM/EDX in order to assess the purity of the siliceous material following extraction. As a result of these tests, a new extraction protocol combining acid digestion, oxidation and dry ashing to acquire pure samples of phytoliths from harvested plants is proposed. In a second step, modern and well dated archaeological materials (harvested plants grown within a FACE experiment and plant residues from a 17th century French mummy) were analyzed in 14C-AMS. Results should allow either to demonstrate the reliability of 14C-AMS analysis of phytolith occluded carbon as a dating tool or trigger further investigations of possible sources of old occluded carbon in phytoliths if the 14C ages are still older than expected.

Effect of Surface Imperfections and Excrescences on the Crossflow Instability

NASA Astrophysics Data System (ADS)

Tufts, Matthew; Duncan, Glen, Jr.; Crawford, Brian; Reed, Helen; Saric, William

2012-11-01

Presented is analysis of the planned SWIFTER experiment to be flown on Texas A&M University's O-2A aircraft. Simultaneous control of the crossflow and streamwise boundary-layer instabilities is a challenge for laminar flow control on swept wings. Solving this problem is an active area of research, with a specific need to quantify the effect of surface imperfections and outer mold line excrescences on crossflow instabilities. The SWIFTER test article is a modification of a prior-tested flight model, with the additional capability of creating controlled excrescences in flight. Using a finite-element Navier-Stokes solution and a spectrally accurate boundary-layer solver, coupled with linear and nonlinear stability analyses, we show that the flow field over the test article is well suited to this study. Results are compared with flight data. The work is supported by the Air Force Research Laboratory through General Dynamics Information Technology, Inc. under sub Agreement No USAF-3446-11-50-SC-01 and the Texas A&M Supercomputing Facility.

Relation between acid dissolution time in the vacuum test tube and time required for graphitization for AMS target preparation

NASA Astrophysics Data System (ADS)

Yokoyama, Yusuke; Miyairi, Yousuke; Matsuzaki, Hiroyuki; Tsunomori, Fumiaki

2007-06-01

Availability of an effective graphitization system is essential for the successful operation of an AMS laboratory for radiocarbon measurements. We have set up a graphitization system consisting of metal vacuum lines for cleaning CO2 sample gas which is then converted to graphite. CO2 gas from a carbonate sample is produced in vacuum in a test tube by injecting concentrated phosphoric acid. The tube is placed into a heated metal block to accelerate dissolution. However, we have observed systematic differences in the time required to convert the CO2 gas to graphite under a hydrogen atmosphere, from less than 3 h to over 10 h. We have conducted a series of experiments including background measurements and yield measurements to monitor secondary carbon contamination and changes in isotopic fractionation. All of the tests show that the carbon isotope ratios remain unaffected by the duration of the process. We also used a quadrupole mass spectrometer (QMS) to identify possible contaminant gases. Contaminant peaks were identified at high mass (larger than 60) only for long duration experiments. This suggests a possible reaction between the rubber cap and acid fumes producing a contaminant gas that impeded the reduction of CO2.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Young Jin

The PowerPoint presentation focused on research goals, specific information about the atomic magnetometer, response and resolution factors of the SERF magnetometer, FC+AM systems, tests of field transfer and resolution on FC, gradient cancellation, testing of AM performance, ideas for a multi-channel AM, including preliminary sensitivity testing, and a description of a 6 channel DAQ system. A few ideas for future work ended the presentation.

Recommended Protocol for Round Robin Studies in Additive Manufacturing

PubMed Central

Moylan, Shawn; Brown, Christopher U.; Slotwinski, John

2016-01-01

One way to improve confidence and encourage proliferation of additive manufacturing (AM) technologies and parts is by generating more high quality data describing the performance of AM processes and parts. Many in the AM community see round robin studies as a way to generate large data sets while distributing the cost among the participants, thereby reducing the cost to individual users. The National Institute of Standards and Technology (NIST) has conducted and participated in several of these AM round robin studies. While the results of these studies are interesting and informative, many of the lessons learned in conducting these studies concern the logistics and methods of the study and unique issues presented by AM. Existing standards for conducting interlaboratory studies of measurement methods, along with NIST’s experience, form the basis for recommended protocols for conducting AM round robin studies. The role of round robin studies in AM qualification, some of the limitations of round robin studies, and the potential benefit of less formal collaborative experiments where multiple factors, AM machine being only one, are varied simultaneously are also discussed. PMID:27274602

Recommended Protocol for Round Robin Studies in Additive Manufacturing.

PubMed

Moylan, Shawn; Brown, Christopher U; Slotwinski, John

2016-03-01

One way to improve confidence and encourage proliferation of additive manufacturing (AM) technologies and parts is by generating more high quality data describing the performance of AM processes and parts. Many in the AM community see round robin studies as a way to generate large data sets while distributing the cost among the participants, thereby reducing the cost to individual users. The National Institute of Standards and Technology (NIST) has conducted and participated in several of these AM round robin studies. While the results of these studies are interesting and informative, many of the lessons learned in conducting these studies concern the logistics and methods of the study and unique issues presented by AM. Existing standards for conducting interlaboratory studies of measurement methods, along with NIST's experience, form the basis for recommended protocols for conducting AM round robin studies. The role of round robin studies in AM qualification, some of the limitations of round robin studies, and the potential benefit of less formal collaborative experiments where multiple factors, AM machine being only one, are varied simultaneously are also discussed.

Power Quality and Reliability Project

NASA Technical Reports Server (NTRS)

Attia, John O.

2001-01-01

One area where universities and industry can link is in the area of power systems reliability and quality - key concepts in the commercial, industrial and public sector engineering environments. Prairie View A&M University (PVAMU) has established a collaborative relationship with the University of'Texas at Arlington (UTA), NASA/Johnson Space Center (JSC), and EP&C Engineering and Technology Group (EP&C) a small disadvantage business that specializes in power quality and engineering services. The primary goal of this collaboration is to facilitate the development and implementation of a Strategic Integrated power/Systems Reliability and Curriculum Enhancement Program. The objectives of first phase of this work are: (a) to develop a course in power quality and reliability, (b) to use the campus of Prairie View A&M University as a laboratory for the study of systems reliability and quality issues, (c) to provide students with NASA/EPC shadowing and Internship experience. In this work, a course, titled "Reliability Analysis of Electrical Facilities" was developed and taught for two semesters. About thirty seven has benefited directly from this course. A laboratory accompanying the course was also developed. Four facilities at Prairie View A&M University were surveyed. Some tests that were performed are (i) earth-ground testing, (ii) voltage, amperage and harmonics of various panels in the buildings, (iii) checking the wire sizes to see if they were the right size for the load that they were carrying, (iv) vibration tests to test the status of the engines or chillers and water pumps, (v) infrared testing to the test arcing or misfiring of electrical or mechanical systems.

The experience of flatus incontinence from a bowel ostomy: a hermeneutic phenomenology.

PubMed

Annells, Merilyn

2006-01-01

To interpret and present possible meanings in the stories of people with bowel ostomies about their experience of impact of flatus incontinence on their life and being. Hermeneutic phenomenology guided by a Gadamerian perspective. Six people with a bowel ostomy were recruited from a city in Australia. In-depth, nonstructured interviews generated rich text. Interviews were videotaped. A variety of interpretive, hermeneutic techniques were applied for text interpretation Nine existential themes of meaning emerged: I am undignified, I am a secret, I am always with gas, I am not myself alone, I am without choice, I am a seeker of control, I am the smell, I am not normal, and I am living a life-sort of. Through symbiotic interpretation, writing, and re-writing, themes were encompassed in a short story: a creative synthesis of actual events and interpreted understandings for ostomates about possible meanings of experiencing flatus incontinence. Flatus incontinence for people with bowel ostomies can be quite discommoding and impact on their interactions, self-image, sexuality, social activity, and psychological well-being. Nurses need to understand this for empathetic interaction, patient assessment, intervention selection, research planning, and pertinent education.

Clinical evaluation of the COBAS Amplicor HBV monitor test for measuring serum HBV DNA and comparison with the Quantiplex branched DNA signal amplification assay in Taiwan.

PubMed

Dai, C-Y; Yu, M-L; Chen, S-C; Lin, Z-Y; Hsieh, M-Y; Wang, L-Y; Tsai, J-F; Chuang, W-L; Chang, W-Y

2004-02-01

To evaluate the performance characteristics and clinical usefulness of the COBAS Amplicor HBV monitor (COBAS-AM) test in Taiwan and to examine its correlation with the Quantiplex branched DNA signal amplification (bDNA) assay for measuring serum hepatitis B virus (HBV) DNA concentrations. HBV DNA was measured by the COBAS-AM test in 149 sera from chronic HBV infected patients that had previously been analysed by the bDNA assay. The COBAS-AM test showed good reproducibility, with acceptable intra-assay and interassay coefficients of variation (1.6% and 0.9%, respectively) and good linearity (r2=0.98). The overall sensitivity of the COBAS-AM test was significantly higher than that of the bDNA assay (95.3% v 83.2%): 69.6% of samples with HBV DNA below the detection limit of the bDNA assay could be measured by the COBAS-AM test. There was a significant correlation between the results of the two assays (r=0.901; p<0.0001). On average, the results derived from the COBAS-AM test were 0.55 log lower than those of the bDNA assay. HBV DNA concentrations were significantly higher among HBV e antigen (HBeAg) positive patients than negative ones, and higher among patients with abnormal alanine aminotransferase (ALT) concentrations than those with normal ALT concentrations (p=0.0003). The COBAS-AM assay, more sensitive in HBeAg negative samples than the bDNA assay, can effectively measure HBV DNA concentrations in Taiwanese patients. HBV DNA values measured by the COBAS-AM test and bDNA assay correlate significantly.

Investigation into the influence of build parameters on failure of 3D printed parts

NASA Astrophysics Data System (ADS)

Fornasini, Giacomo

Additive manufacturing, including fused deposition modeling (FDM), is transforming the built world and engineering education. Deep understanding of parts created through FDM technology has lagged behind its adoption in home, work, and academic environments. Properties of parts created from bulk materials through traditional manufacturing are understood well enough to accurately predict their behavior through analytical models. Unfortunately, Additive Manufacturing (AM) process parameters create anisotropy on a scale that fundamentally affects the part properties. Understanding AM process parameters (implemented by program algorithms called slicers) is necessary to predict part behavior. Investigating algorithms controlling print parameters (slicers) revealed stark differences between the generation of part layers. In this work, tensile testing experiments, including a full factorial design, determined that three key factors, width, thickness, infill density, and their interactions, significantly affect the tensile properties of 3D printed test samples.

Combined use of alcohol and energy drinks: Dose relationship with self-reported physiological stimulation and sedation side effects.

PubMed

Droste, Nicolas; Peacock, Amy; Bruno, Raimondo; Pennay, Amy; Zinkiewicz, Lucy; Lubman, Dan I; Miller, Peter

2017-08-01

Negative physiological stimulation and sedation side effects are experienced by a significant proportion of consumers who consume alcohol mixed with energy drinks (AmED). Few studies have compared the frequency of side effects between sessions of AmED and sessions of alcohol only within-subject, and none have explored a dose relationship. Explore the occurrence of self-reported physiological stimulant and sedative side effects between sessions of AmED and alcohol only, and at varying ED dosage levels within AmED sessions. A convenience sample of 2953 residents of New South Wales, Australia completed an online survey. N=731 AmED users reported daily caffeine intake, typical alcohol and AmED consumption, and past 12-month experience of physiological stimulation and sedation side effects during AmED and alcohol only sessions. Within-subject analyses compared occurrence of side effects between session types. Hierarchical binary logistic regression analyses explored the association of ED dose during AmED sessions with the experience of physiological side effects. There were greater odds of most stimulant side effects, and lower odds of sedation side effects, during AmED sessions compared to alcohol only sessions. Compared to one ED, consumption of three or more EDs was significantly associated with the majority of both stimulant and alcohol intoxication side effects after controlling for demographics and consumption covariates. AmED is associated with perceived changes in physiological stimulant and sedation side effects of alcohol. Experience of side effects is positively associated with ED dosage. Future research should account for varying ED dosage, and reflect real world consumption levels. Copyright © 2017 Elsevier Ltd. All rights reserved.

Teacher Professional Development in Laredo, TX

NASA Astrophysics Data System (ADS)

Finkelstein, Keely D.; Macri, L. M.; Hemenway, M.; Wetzel, M.; Preston, S.; Rood, M.

2014-01-01

In the fall of 2012, McDonald Observatory, Texas A&M University, and Texas A&M International University conducted a series of workshops on astronomy content for 5th - 8th grade teachers in Laredo, Texas. Three one-day workshops were held at the Lamar Bruni Vergara Planetarium of Texas A&M International University, using a mix of in-person and distance learning technology. Texas A&M professor Lucas Macri gave public talks in English and Spanish, and a lunch-time presentation to the teachers. A series of evaluation tools were used to assess the success of the workshops. A Nominal Group Technique (NGT) discussion was used, through which groups developed consensus answers about their learning, expectations for classroom use, and satisfaction with the workshop. The Astronomy/Space Science Test (MOSART Grades 5-8) was also issued as a pre- and post-test to assess gains in knowledge. Teacher consensus was that the materials and activities of the workshop had been helpful for learning and that they expected to use many of them in their classrooms. However, the evaluation also showed that teachers would have preferred the Observatory educator be physically present for all workshops. Past video-conferencing workshops, where local facilitators first participated in workshops at the Observatory, showed better feedback and results concerning this point. Comparing those results to the present case, we conclude that more clearly defined roles and better training for the science specialists and local facilitators would improve the video conference experience for the teachers. Comparison of pre- and post-test results showed improved teacher knowledge. An additional benefit of this project was the further development of partnerships between McDonald Observatory and Texas A&M International University, which has resulted in further education projects, including a video-conference presentation series to eight-grade students and their families. This secondary project focused on motivating and increasing underserved students from the Laredo area in STEM fields, and featured lectures from University of Texas / McDonald Observatory astronomers.

Rolling-element fatigue life of AMS 5749 corrosion resistant, high temperature bearing steel

NASA Technical Reports Server (NTRS)

Parker, R. J.; Hodder, R. S.

1977-01-01

The rolling element fatigue lives of AMS 5749 and AISI M-50 were compared in tests run in the five ball fatigue tester and the rolling contact fatigue tester. The effects of double vacuum melting and retained austenite on the life of AMS 5749 were determined in five ball fatigue tests. The double vacuum melting process consisted of induction vacuum melting followed by vacuum arc remelting (VIM-VAR). In the five ball tests, VIM-VAR AMS 5749 gave lives at least six times that of VIM-VAR AISI M-50. Similar tests in the rolling contact fatigue tester showed no significant difference in the lives of the two materials. The rolling element fatigue life of VIM-VAR AMS 5749 was at least 14 times that of vacuum induction melted AMS 5749. A trend toward increased rolling element fatigue life with decreased retained austenite is apparent, but the confidence that all experimental differences are significant is not great.

Accelerated Learning: Undergraduate Research Experiences at the Texas A&M Cyclotron Institute

NASA Astrophysics Data System (ADS)

Yennello, S. J.

The Texas A&M Cyclotron Institute (TAMU CI) has had an NSF funded Research Experiences for Undergraduates program since 2004. Each summer about a dozen students from across the country join us for the 10-week program. They are each imbedded in one of the research groups of the TAMU CI and given their own research project. While the main focus of their effort is their individual research project, we also have other activities to broaden their experience. For instance, one of those activities has been involvement in a dedicated group experiment. Because not every experimental group will run during those 10 weeks and the fact that some of the students are in theory research groups, a group research experience allows everyone to actually be involved in an experiment using the accelerator. In stark contrast to the REU students' very focused experience during the summer, Texas A&M undergraduates can be involved in research projects at the Cyclotron throughout the year, often for multiple years. This extended exposure enables Texas A&M students to have a learning experience that cannot be duplicated without a local accelerator. The motivation for the REU program was to share this accelerator experience with students who do not have that opportunity at their home institution.

Integrated corridor management analysis, modeling, and simulation experimental plan for the test corridor.

DOT National Transportation Integrated Search

2008-03-01

This document, the AMS Experimental Plan, lays out the scope of analysis that will be conducted through the application of the AMS methodology to the Test Corridor. The specific objectives of the Experimental Plan are: create an AMS framework that id...

THER ROLE OF REMOTE SENSING AND GIS IN IDENTIFYING AND REMOVING BURIED WORLD WAR I MUNITIONS AT THE AMERICAN UNIVERSITY, WASHINGTON, DC

EPA Science Inventory

During World War I, The American University in Washington D.C. was used by the U.S. Am1y as an experiment station for the development and testing of a variety of battlefield munitions including chemical weapons such as Mustard Gas, Phosgene, Ricin and Lewisite, among others. Afte...

Comparison of in situ forces and knee kinematics in anteromedial and high anteromedial bundle augmentation for partially ruptured anterior cruciate ligament.

PubMed

Xu, Yan; Liu, Jianyu; Kramer, Scott; Martins, Cesar; Kato, Yuki; Linde-Rosen, Monica; Smolinski, Patrick; Fu, Freddie H

2011-02-01

High tunnel placement is common in single- and double-bundle anterior cruciate ligament (ACL) reconstructions. Similar nonanatomic tunnel placement may also occur in ACL augmentation surgery. In this study, in situ forces and knee kinematics were compared between nonanatomic high anteromedial (AM) and anatomic AM augmentation in a knee with isolated AM bundle injury. Controlled laboratory study. Seven fresh-frozen cadaver knees were used (age, 48 ± 12.5 years). First, intact knee kinematics was tested with a robotic-universal force sensor testing system under 2 loading conditions. An 89-N anterior load was applied, and an anterior tibial translation was measured at knee flexion angles of 0°, 30°, 60°, and 90°. Then, combined rotatory loads of 7-N·m valgus and 5-N·m internal tibial rotation were applied at 15° and 30° of knee flexion angles, which mimic the pivot shift. Afterward, only the AM bundle of the ACL was cut arthroscopically, keeping the posterolateral bundle intact. The knee was again tested using the intact knee kinematics to measure the in situ force of the AM bundle. Then, arthroscopic anatomic AM bundle reconstruction was performed with an allograft, and the knee was tested to give the in situ force of the reconstructed AM bundle. Knee kinematics under the 3 conditions (intact, anatomic AM augmentation, and nonanatomic high AM augmentation) and the in situ force were compared and analyzed. The high AM graft had significantly lower in situ force than the intact and anatomic reconstructed AM bundle at 0° of knee flexion (P < .05) and the intact AM bundle at 30° of knee flexion under anterior tibial loading. There were no differences between anatomic graft and intact AM bundle. The high AM graft also had a significantly lower in situ force than the intact and anatomic reconstructed AM with simulated pivot-shift loading at 15° and 30° of flexion (P < .05). Under anterior tibial and rotatory loading, there was a difference in tibial displacement between anatomic and high AM reconstructions and between the high AM graft and intact ACL under rotational loading with the knee at 15° of flexion. Anatomic AM augmentation can lead to biomechanical advantages at time zero when compared with the nonanatomic (high AM) augmentation. Anatomic AM augmentation better restores the knee kinematics to the intact ACL state.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) Program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the university students prepare their rocket for flight on the launch pad. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the University students prepare their rocket for launch. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Around Marshall

NASA Image and Video Library

2002-05-22

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the University students prepare their rocket for launch. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Around Marshall

NASA Image and Video Library

2002-05-22

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) Program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the university students prepare their rocket for flight on the launch pad. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Association of Cognitive Performance with Time at Altitude, Sleep Quality, and Acute Mountain Sickness Symptoms.

PubMed

Issa, Amine N; Herman, Nicole M; Wentz, Robert J; Taylor, Bryan J; Summerfield, Doug C; Johnson, Bruce D

2016-09-01

It is well documented that cognitive performance may be altered with ascent to altitude, but the association of various cognitive performance tests with symptoms of acute mountain sickness (AMS) is not well understood. Our objective was to assess and compare cognitive performance during a high-altitude expedition using several tests and to report the association of each test with AMS, headache, and quality of sleep. During an expedition to Mount Everest, 3 cognitive tests (Stroop, Trail Making, and the real-time cognitive assessment tool, an in-house developed motor accuracy test) were used along with a questionnaire to assess health and AMS. Eight team members were assessed pre-expedition, postexpedition, and at several time points during the expedition. There were no significant differences (P >.05) found among scores taken at 3 time points at base camp and the postexpedition scores for all 3 tests. Changes in the Stroop test scores were significantly associated with the odds of AMS (P <.05). The logistic regression results show that the percent change from baseline for Stroop score (β = -5.637; P = .032) and Stroop attempts (β = -5.269; P = .049) are significantly associated with the odds of meeting the criteria for AMS. No significant changes were found in overall cognitive performance at altitude, but a significant relationship was found between symptoms of AMS and performance in certain cognitive tests. This research shows the need for more investigation of objective physiologic assessments to associate with self-perceived metrics of AMS to gauge effect on cognitive performance. Crown Copyright © 2016. Published by Elsevier Inc. All rights reserved.

Laboratory investigation of the role of desorption kinetics on americium transport associated with bentonite colloids

DOE PAGES

Dittrich, Timothy Mark; Boukhalfa, Hakim; Ware, Stuart Douglas; ...

2015-07-13

Understanding the parameters that control colloid-mediated transport of radionuclides is important for the safe disposal of used nuclear fuel. We report an experimental and reactive transport modeling examination of americium transport in a groundwater–bentonite–fracture fill material system. A series of batch sorption and column transport experiments were conducted to determine the role of desorption kinetics from bentonite colloids in the transport of americium through fracture materials. We used fracture fill material from a shear zone in altered granodiorite collected from the Grimsel Test Site (GTS) in Switzerland and colloidal suspensions generated from FEBEX bentonite, a potential repository backfill material. Themore » colloidal suspension (100 mg L –1) was prepared in synthetic groundwater that matched the natural water chemistry at GTS and was spiked with 5.5 × 10 –10 M 241Am. Batch characterizations indicated that 97% of the americium in the stock suspension was adsorbed to the colloids. Breakthrough experiments conducted by injecting the americium colloidal suspension through three identical columns in series, each with mean residence times of 6 h, show that more than 95% of the bentonite colloids were transported through each of the columns, with modeled colloid filtration rates (k f) of 0.01–0.02 h –1. Am recoveries in each column were 55–60%, and Am desorption rate constants from the colloids, determined from 1-D transport modeling, were 0.96, 0.98, and 0.91 h –1 in the three columns, respectively. The consistency in Am recoveries and desorption rate constants in each column indicates that the Am was not associated with binding sites of widely-varying strengths on the colloids, as one binding site with fast kinetics represented the system accurately for all three sequential columns. As a result, our data suggest that colloid-mediated transport of Am in a bentonite-fracture fill material system is unlikely to result in transport over long distance scales because of the ability of the fracture materials to rapidly strip Am from the bentonite colloids and the apparent lack of a strong binding site that would keep a fraction of the Am strongly-associated with the colloids.« less

Herald : field operational test evaluation final report

DOT National Transportation Integrated Search

2000-09-01

The Herald Field Operational Test (FOT) tested AM radio as a low-cost way to broadcast traveler information in rural areas. It tested the feasibility of broadcasting data on the inaudible portion of an existing AM broadcast. Two systems were tested, ...

Herald Field Operation Test Evaluation : Final Report

DOT National Transportation Integrated Search

2000-09-01

The Herald Field Operational Test (FOT) tested AM radio as a low-cost way to broadcast traveler information in rural areas. It tested the feasibility of broadcasting data on the inaudible portion of an existing AM broadcast. Two systems were tested, ...

Self-absorption Effects on Alpha-Induced Atmospheric Nitrogen Fluorescence Yield

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bachelor, Paula P.; Jordan, David V.; Harper, Warren W.

2009-12-01

Nitrogen fluorescence induced by alpha, beta and gamma radiation can be used to detect the presence of radioactive contamination in the environment. Successful measurement of fluorescence yield involves a number of factors, including: known fluorescence signal rate during the measurement; the effective alpha spectrum of the radioactive sources used in the measurement; optical attenuation length of the fluorescence signal in air during the measurement; the absolute throughput of the instrumentation; calibration of the instrumentation; and radiation transport modeling of the "effective" array exposure rate given the spectrum of the alpha particles. Field testing of optical instrumentation was conducted to measuremore » the nitrogen fluorescence yield from the alpha radiation generated from americium-241 (241Am) decay. The 241Am test sources were prepared by direct evaporation of ~1 mCi in nitric acid solution, and some solids were visible on the surface of the sources. A laboratory study was conducted with lower activities of 241Am to determine whether the presence of solids on the surface of the sources prepared both by direct evaporation and by electrodeposition onto stainless steel disks produced sufficient self-absorption to cause a decrease in expected fluorescence. Alpha spectroscopy was used to determine the apparent activity of the sources versus the known activity deposited on the surface. Results from the self-absorption laboratory studies were used to correct the activity values in the model and calculate the nitrogen fluorescence generated by the 241Am during the field experiments.« less

Social Simulation for AmI Systems Engineering

NASA Astrophysics Data System (ADS)

Garcia-Valverde, Teresa; Serrano, Emilio; Botia, Juan A.

This paper propose the use of multi-agent based simulation (MABS) to allow testing, validating and verifying Ambient Intelligence (AmI) environments in a flexible and robust way. The development of AmI is very complex because of this technology must often adapt to contextual information as well as unpredictable and changeable behaviours. The concrete simulation is called Ubik and is integrated into the AmISim architecture which is also presented in this paper. This architecture deals with AmI applications in order to discover defects, estimate quality of applications, help to make decisions about the design, etc. The paper shows that Ubik and AmISim provide a simulation framework which can test scenarios that would be impossible in real environments or even with previous AmI simulation approaches.

The Texas A&M Radioisotope Production and Radiochemistry Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akabani, Gamal

The main motivation of the project at Texas A&M University was to carry out the production of critically needed radioisotopes used in medicine for diagnostic and therapy, and to establish an academic program in radionuclide production and separation methods. After a lengthy battle with the Texas A&M University Radiation Safety Office, the Texas Department of State Health Services granted us a license for the production of radionuclides in July 2015, allowing us to work in earnest in our project objectives. Experiments began immediately after licensing, and we started the assembly and testing of our target systems. There were four analytical/theoreticalmore » projects and two experimental target systems. These were for At-211 production and for Zn- 62/Cu-62 production. The theoretical projects were related to the production of Mo-99/Tc-99m using (a) a subcritical aqueous target system and (b) production of Tc-99m from accelerator-generated Mo-99 utilizing a photon-neutron interaction with enriched Mo-100 targets. The two experimental projects were the development of targetry systems and production of At-211 and Zn-62/Cu-62 generator. The targetry system for At-211 has been tested and production of At-211 is chronic depending of availability of beam time at the cyclotron. The installation and testing of the targetry system for the production of Zn-62/Cu-62 has not been finalized. A description of the systems is described. The academic program in radionuclide production and separation methods was initiated in the fall of 2011; due to the lack of a radiochemistry laboratory, it was suspended. We expect to re-start the academic program at the Texas A&M Institute for Preclinical Studies under the Molecular Imaging Program.« less

The Texas A&M Radioisotope Production and Radiochemistry Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akabani, Gamal

The main motivation of the project at Texas A&M University was to carry out the production of critically needed radioisotopes used in medicine for diagnostics and therapy, and to establish an academic program in radionuclide production and separation methods. After a lengthy battle with the Texas A&M University Radiation Safety Office, the Texas Department of State Health Services granted us a license for the production of radionuclides in July 2015, allowing us to work in earnest in our project objectives. Experiments began immediately after licensing, and we started the assembly and testing of our target systems. There were four analytical/theoreticalmore » projects and two experimental target systems. These were for At-211 production and for Zn-62/Cu-62 production. The theoretical projects were related to the production of Mo-99/Tc-99m using a) a subcritical aqueous target system and b) production of Tc-99m from accelerator-generated Mo-99 utilizing a photon-neutron interaction with enriched Mo-100 targets. The two experimental projects were the development of targetry systems and production of At-211 and Zn-62/Cu-62 generator. The targetry system for At-211 has been tested and production of At-211 is chronic depending of availability of beam time at the cyclotron. The installation and testing of the targetry system for the production of Zn-62/Cu-62 has not been finalized. A description of the systems is described. The academic program in radionuclide production and separation methods was initiated in the fall of 2011 and, due to the lack of a radiochemistry laboratory, it was suspended. We expect to re-start the academic program at the Texas A&M Institute for Preclinical Studies under the Molecular Imaging Program.« less

Interpretation of actinide-distribution data obtained from non-destructive and destructive post-test analyses of an intact-core column of Culebra dolomite.

PubMed

Perkins, W G; Lucero, D A

2001-02-01

The US Department of Energy (DOE), with technical assistance from Sandia National Laboratories, has successfully received EPA certification and opened the Waste Isolation Pilot Plant (WIPP), a nuclear waste disposal facility located approximately 42 km east of Carlsbad, NM. Performance assessment (PA) analyses indicate that human intrusions by inadvertent, intermittent drilling for resources provide the only credible mechanisms for significant releases of radionuclides from the disposal system. For long-term brine releases, migration pathways through the permeable layers of rock above the Salado formation are important. Major emphasis is placed on the Culebra Member of the Rustler Formation because this is the most transmissive geologic layer overlying the WIPP site. In order to help quantify parameters for the calculated releases, radionuclide transport experiments have been carried out using intact-core columns obtained from the Culebra dolomite member of the Rustler Formation within the WIPP site. This paper deals primarily with results of analyses for 241Pu and 241Am distributions developed during transport experiments in one of these cores. Transport experiments were done using a synthetic brine that simulates Culebra brine at the core recovery location (the WIPP air-intake shaft (AIS)). Hydraulic characteristics (i.e., apparent porosity and apparent dispersion coefficient) for intact-core columns were obtained via experiments using the conservative tracer 22Na. Elution experiments carried out over periods of a few days with tracers 232U and 239Np indicated that these tracers were weakly retarded as indicated by delayed elution of the species. Elution experiments with tracers 241Pu and 241Am were attempted but no elution of either species has been observed to date, including experiments of many months' duration. In order to quantify retardation of the non-eluted species 241Pu and 241Am after a period of brine flow, non-destructive and destructive analyses of one intact-core column were carried out to determine distribution of these actinides in the rock. Analytical results indicate that the majority of the 241Am remained very near the injection surface of the core (possibly as a precipitate), and that the majority of the 241Pu was dispersed with a very high apparent retardation value. The 241Pu distribution is interpreted using a single-porosity advection-dispersion model, and an approximate retardation value is reported.

Diffusion of Antimicrobials Across Silicone Hydrogel Contact Lenses.

PubMed

Zambelli, Alison M; Brothers, Kimberly M; Hunt, Kristin M; Romanowski, Eric G; Nau, Amy C; Dhaliwal, Deepinder K; Shanks, Robert M Q

2015-09-01

To measure the diffusion of topical preparations of moxifloxacin, amphotericin B (AmB), and polyhexamethylene biguanide (PHMB) through silicone hydrogel (SH) contact lenses (CLs) in vitro. Using an in vitro model, the diffusion of three antimicrobials through SH CLs was measured. Diffused compounds were measured using a spectrophotometer at set time points over a period of 4 hr. The amount of each diffused antimicrobial was determined by comparing the experimental value with a standard curve. A biological assay was performed to validate the CL diffusion assay by testing antimicrobial activity of diffused material against lawns of susceptible bacteria (Staphylococcus epidermidis) and yeast (Saccharomyces cerevisiae). Experiments were repeated at least two times with a total of at least four independent replicates. Our data show detectable moxifloxacin and PHMB diffusion through SH CLs at 30 min, whereas AmB diffusion remained below the limit of detection within the 4-hr experimental period. In the biological assay, diffused moxifloxacin demonstrated microbial killing starting at 20 min on bacterial lawns, whereas PHMB and AmB failed to demonstrate killing on microbial lawns over the course of the 60-min experiment. In vitro diffusion assays demonstrate limited penetration of certain anti-infective agents through SH CLs. Further studies regarding the clinical benefit of using these agents along with bandage CL for corneal pathologic condition are warranted.

3D printed drug delivery and testing systems - a passing fad or the future?

PubMed

Lim, Seng Han; Kathuria, Himanshu; Tan, Justin Jia Yao; Kang, Lifeng

2018-05-18

The US Food and Drug Administration approval of the first 3D printed tablet in 2015 has ignited growing interest in 3D printing, or additive manufacturing (AM), for drug delivery and testing systems. Beyond just a novel method for rapid prototyping, AM provides key advantages over traditional manufacturing of drug delivery and testing systems. These includes the ability to fabricate complex geometries to achieve variable drug release kinetics; ease of personalising pharmacotherapy for patient and lowering the cost for fabricating personalised dosages. Furthermore, AM allows fabrication of complex and micron-sized tissue scaffolds and models for drug testing systems that closely resemble in vivo conditions. However, there are several limitations such as regulatory concerns that may impede the progression to market. Here, we provide an overview of the advantages of AM drug delivery and testing, as compared to traditional manufacturing techniques. Also, we discuss the key challenges and future directions for AM enabled pharmaceutical applications. Copyright © 2018 Elsevier B.V. All rights reserved.

Arbuscular mycorrhizal fungal hyphae contribute to the uptake of polycyclic aromatic hydrocarbons by plant roots.

PubMed

Gao, Yanzheng; Cheng, Zhaoxia; Ling, Wanting; Huang, Jing

2010-09-01

The arbuscular mycorrhizal (AM) hyphae-mediated uptake of polycyclic aromatic hydrocarbons (PAHs) by the roots of ryegrass (Lolium multiflorum Lam.) was investigated using three-compartment systems. Glomus mosseae and Glomus etunicatum were chosen, and fluorene and phenanthrene were used as representative PAHs. When roots were grown in un-spiked soils, AM hyphae extended into PAH-spiked soil and clearly absorbed and transported PAHs to roots, resulting in high concentrations of fluorene and phenanthrene in roots. This was further confirmed by the batch equilibration experiment, which revealed that the partition coefficients (K(d)) of tested PAHs by mycorrhizal hyphae were 270-356% greater than those by roots, suggesting the great potential of hyphae to absorb PAHs. Because of fluorene's lower molecular weight and higher water solubility, its translocation by hyphae was greater than that of phenanthrene. These results provide new perspectives on the AM hyphae-mediated uptake by plants of organic contaminants from soil. Copyright 2010 Elsevier Ltd. All rights reserved.

Chromium resistance of dandelion (Taraxacum platypecidum Diels.) and bermudagrass (Cynodon dactylon [Linn.] Pers.) is enhanced by arbuscular mycorrhiza in Cr(VI)-contaminated soils.

PubMed

Wu, Song-Lin; Chen, Bao-Dong; Sun, Yu-Qing; Ren, Bai-Hui; Zhang, Xin; Wang, You-Shan

2014-09-01

In a greenhouse pot experiment, dandelion (Taraxacum platypecidum Diels.) and bermudagrass (Cynodon dactylon[Linn.] Pers.), inoculated with and without arbuscular mycorrhizal fungus (AMF) Rhizophagus irregularis, were grown in chromium (Cr)-amended soils (0 mg/kg, 5 mg/kg, 10 mg/kg, and 20 mg/kg Cr[VI]) to test whether arbuscular mycorrhizal (AM) symbiosis can improve Cr tolerance in different plant species. The experimental results indicated that the dry weights of both plant species were dramatically increased by AM symbiosis. Mycorrhizal colonization increased plant P concentrations and decreased Cr concentrations and Cr translocation from roots to shoots for dandelion; in contrast, mycorrhizal colonization decreased plant Cr concentrations without improvement of P nutrition in bermudagrass. Chromium speciation analysis revealed that AM symbiosis potentially altered Cr species and bioavailability in the rhizosphere. The study confirmed the protective effects of AMF on host plants under Cr contaminations. © 2014 SETAC.

Skylab

NASA Image and Video Library

1972-01-01

This photograph depicts the flight article of the Airlock Module (AM) Flight Article being mated to the Fixed Airlock Shroud and aligned in a clean room of the McDornell Douglas Plant in St. Louis, Missouri. The AM enabled crew members to conduct extravehicular activities outside Skylab as required for experiment support. Separated from the Workshop and the Multiple Docking Adapter by doors, the AM could be evacuated for egress or ingress of a space-suited astronaut through a side hatch. Oxygen and nitrogen storage tanks needed for Skylab's life support system were mounted on the external truss work of the AM. Major components in the AM included Skylab's electric power control and distribution station, environmental control system, communication system, and data handling and recording systems. The Marshall Space Flight Center was responsible for the design and development of the Skylab hardware and experiment management.

Microstructure and corrosion behavior of die-cast AM60B magnesium alloys in a complex salt solution. A slow positron beam study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Y. F.; Yang, W.; Qin, Q. L.

2013-12-15

The microstructure and corrosion behavior of high pressure die-cast (HPDC) and super vacuum die-cast (SVDC) AM60B magnesium alloys were investigated in a complex salt solution using slow positron beam technique and potentiodynamic polarization tests. The experiments revealed that a CaCO 3 film was formed on the surface of the alloys and that the rate of CaCO 3 formation for the SVDC alloy with immersion time was slower than that of the HPDC alloy. The larger volume fraction of b-phase in the skin layer of the SVDC alloy than that of the HPDC alloy was responsible for the better corrosion resistance.

STS-29 Landing Approach at Edwards

NASA Image and Video Library

1989-03-18

The STS-29 Space Shuttle Discovery mission approaches for a landing at NASA's then Ames-Dryden Flight Research Facility, Edwards AFB, California, early Saturday morning, 18 March 1989. Touchdown was at 6:35:49 a.m. PST and wheel stop was at 6:36:40 a.m. on runway 22. Controllers chose the concrete runway for the landing in order to make tests of braking and nosewheel steering. The STS-29 mission was very successful, completing the launch a Tracking and Data Relay communications satellite, as well as a range of scientific experiments. Discovery's five man crew was led by Commander Michael L. Coats, and included pilot John E. Blaha and mission specialists James P. Bagian, Robert C. Springer, and James F. Buchli.

Experimente ueber den Einflusse von Metaboliten und Antimetaboliten am Model von Trichomonas Vaginalis. II. Mitteilung: Experimente mit der Vitamin K-Gruppe (Experiments on the Influence of Metabolites and Antimetabolites on the Model of Trichomonas Vaginalis. II. Communication: Experiments with the Vitamin K-Group),

DTIC Science & Technology

K4 essential reduction of multiplication of Trichomonas vaginalis was observed within a range of 0.25 and 0.35 mg/ml, from 0.40 mg/ml onward single...The aim of the investigation was to test the relationship between the individual K-vitamins K1, K3, K4 and K5 and Trichomonas analytically. The...show any remarkable differences between the control culture and the test series (Table 1) in Trichomonas multiplication. With vitamin K3 gradually

A comparative study of three cytotoxicity test methods for nanomaterials using sodium lauryl sulfate.

PubMed

Kwon, Jae-Sung; Kim, Kwang-Mahn; Kim, Kyoung-Nam

2014-10-01

The biocompatibility evaluation of nanomaterials is essential for their medical diagnostic and therapeutic usage, where a cytotoxicity test is the simplest form of biocompatibility evaluation. Three methods have been commonly used in previous studies for the cytotoxicity testing of nanomaterials: trypan blue exclusion, colorimetric assay using water soluble tetrazolium (WST), and imaging under a microscope following calcein AM/ethidium homodimer-1 staining. However, there has yet to be a study to compare each method. Therefore, in this study three methods were compared using the standard reference material of sodium lauryl sulfate (SLS). Each method of the cytotoxicity test was carried out using mouse fibroblasts of L-929 exposed to different concentrations of SLS. Compared to the gold standard trypan blue exclusion test, both colorimetric assay using water soluble tetrazolium (WST) and imaging under microscope with calcein AM/ethidium homodimer-1 staining showed results that were not statistically different. Also, each method exhibited various advantages and disadvantages, which included the need of equipment, time taken for the experiment, and provision of additional information such as cell morphology. Therefore, this study concludes that all three methods of cytotoxicity testing may be valid, though careful consideration will be needed when selecting tests with regard to time, finances, and the amount of information required by the researcher(s).

Development of Metallic Fuels for Actinide Transmutation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hayes, Steven Lowe; Fielding, Randall Sidney; Benson, Michael Timothy

Research and development activities on metallic fuels are focused on their potential use for actinide transmutation in future sodium fast reactors. As part of this application, there is also a need for a near zero-loss fabrication process and a desire to demonstrate a multifold increase in burnup potential. The incorporation of Am and Np into the traditional U-20Pu-10Zr metallic fuel alloy was demonstrated in the US during the Integral Fast Reactor Program of the 1980’s and early 1990’s. However, the conventional counter gravity injection casting method performed under vacuum, previously used to fabricate these metallic fuel alloys, was not optimizedmore » for mitigating loss of the volatile Am constituent in the casting charge; as a result, approximately 40% of the Am casting charge failed to be incorporated into the as-cast fuel alloys. Fabrication development efforts of the past few years have pursued an optimized bottom-pour casting method to increase utilization of the melted charge to near 100%, and a differential pressure casting approach, performed under an argon overpressure, has been demonstrated to result in essentially no loss of Am due to volatilization during fabrication. In short, a path toward zero-loss fabrication of metallic fuels including minor actinides has been shown to be feasible. Irradiation testing of advanced metallic fuel alloys in the Advanced Test Reactor (ATR) has been underway since 2003. Testing in the ATR is performed inside of cadmium-shrouded positions to remove >99% of the thermal flux incident on the test fuels, resulting in an epi-thermal driven fuel test that is free from gross flux depression and producing an essentially prototypic radial temperature profile inside the fuel rodlets. To date, three irradiation test series (AFC-1,2,3) have been completed. Over 20 different metallic fuel alloys have been tested to burnups as high as 30% with constituent compositions of Pu up to 30%, Am up to 12%, Np up to 10%, and Zr between 10 and 60%. In general, the performance of all of these substantially disparate metallic fuel alloys has been observed to be excellent, and their irradiation behaviors are generally consistent with historic norms for metallic fuels without minor actinide additions and having lower Pu or Zr contents. Future work is being undertaken with a view toward increasing the burnup potential of metallic fuels even more. Design innovations under investigation include: 1) lowering the fuel smear density in order to accommodate more swelling, 2) annular fuel geometry to eliminate the need for a sodium bond, 3) minor alloy additions to stabilize lanthanide fission products inside the fuel and prevent their transport to the cladding where they can participate in fuel-cladding chemical interaction (FCCI), and 4) coatings/liners on the cladding inner surface to mitigate FCCI and enable higher temperature operation. This paper will present the current state of development of metallic fuels for actinide transmutation in the US. Highlights will include recent results from metallic fuel casting experiments, experiments to identify alloy additions to immobilize lanthanide fission products, and postirradiation examinations of annular metallic fuels at low burnup.« less

Symbiotic soil fungi enhance ecosystem resilience to climate change.

PubMed

Martínez-García, Laura B; De Deyn, Gerlinde B; Pugnaire, Francisco I; Kothamasi, David; van der Heijden, Marcel G A

2017-12-01

Substantial amounts of nutrients are lost from soils through leaching. These losses can be environmentally damaging, causing groundwater eutrophication and also comprise an economic burden in terms of lost agricultural production. More intense precipitation events caused by climate change will likely aggravate this problem. So far it is unresolved to which extent soil biota can make ecosystems more resilient to climate change and reduce nutrient leaching losses when rainfall intensity increases. In this study, we focused on arbuscular mycorrhizal (AM) fungi, common soil fungi that form symbiotic associations with most land plants and which increase plant nutrient uptake. We hypothesized that AM fungi mitigate nutrient losses following intensive precipitation events (higher amount of precipitation and rain events frequency). To test this, we manipulated the presence of AM fungi in model grassland communities subjected to two rainfall scenarios: moderate and high rainfall intensity. The total amount of nutrients lost through leaching increased substantially with higher rainfall intensity. The presence of AM fungi reduced phosphorus losses by 50% under both rainfall scenarios and nitrogen losses by 40% under high rainfall intensity. Thus, the presence of AM fungi enhanced the nutrient interception ability of soils, and AM fungi reduced the nutrient leaching risk when rainfall intensity increases. These findings are especially relevant in areas with high rainfall intensity (e.g., such as the tropics) and for ecosystems that will experience increased rainfall due to climate change. Overall, this work demonstrates that soil biota such as AM fungi can enhance ecosystem resilience and reduce the negative impact of increased precipitation on nutrient losses. © 2017 The Authors. Global Change Biology Published by John Wiley & Sons Ltd.

Evaluation of the Eberline AMS-3A and AMS-4 Beta continuous air monitors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, M.L.; Sisk, D.R.

1996-03-01

Eberline AMS-3A-1 and AMS-4 beta continuous air monitors were tested against the criteria set forth in the ANSI Standards N42.18, Specification and Performance of On-site Instrumentation for Continuously Monitoring Radioactivity in Effluents, and ANSI N42.17B, Performance Specification for Health Physics Instrumentation - Occupational Airborne Radioactivity Monitoring Instrumentation. ANSI N42.18 does not, in general, specify testing procedures for demonstrating compliance with the criteria set forth in the standard; therefore, wherever possible, the testing procedures given in ANSI N42.17B were adopted. In all cases, the more restrictive acceptance criteria and/or the more demanding test conditions of the two standards were used.

Overview of AMS (CCSDS Asynchronous Message Service)

NASA Technical Reports Server (NTRS)

Burleigh, Scott

2006-01-01

This viewgraph presentation gives an overview of the Consultative Committee for Space Data Systems (CCSDS) Asynchronous Message Service (AMS). The topics include: 1) Key Features; 2) A single AMS continuum; 3) The AMS Protocol Suite; 4) A multi-continuum venture; 5) Constraining transmissions; 6) Security; 7) Fault Tolerance; 8) Performance of Reference Implementation; 9) AMS vs Multicast (1); 10) AMS vs Multicast (2); 11) RAMS testing exercise; and 12) Results.

Contribution of amygdalar and lateral hypothalamic neurons to visual information processing of food and nonfood in monkey.

PubMed

Ono, T; Tamura, R; Nishijo, H; Nakamura, K; Tabuchi, E

1989-02-01

Visual information processing was investigated in the inferotemporal cortical (ITCx)-amygdalar (AM)-lateral hypothalamic (LHA) axis which contributes to food-nonfood discrimination. Neuronal activity was recorded from monkey AM and LHA during discrimination of sensory stimuli including sight of food or nonfood. The task had four phases: control, visual, bar press, and ingestion. Of 710 AM neurons tested, 220 (31.0%) responded during visual phase: 48 to only visual stimulation, 13 (1.9%) to visual plus oral sensory stimulation, 142 (20.0%) to multimodal stimulation and 17 (2.4%) to one affectively significant item. Of 669 LHA neurons tested, 106 (15.8%) responded in the visual phase. Of 80 visual-related neurons tested systematically, 33 (41.2%) responded selectively to the sight of any object predicting the availability of reward, and 47 (58.8%) responded nondifferentially to both food and nonfood. Many of AM neuron responses were graded according to the degree of affective significance of sensory stimuli (sensory-affective association), but responses of LHA food responsive neurons did not depend on the kind of reward indicated by the sensory stimuli (stimulus-reinforcement association). Some AM and LHA food responses were modulated by extinction or reversal. Dynamic information processing in ITCx-AM-LHA axis was investigated by reversible deficits of bilateral ITCx or AM by cooling. ITCx cooling suppressed discrimination by vision responding AM neurons (8/17). AM cooling suppressed LHA responses to food (9/22). We suggest deep AM-LHA involvement in food-nonfood discrimination based on AM sensory-affective association and LHA stimulus-reinforcement association.

Engineering sciences area and module performance and failure analysis area

NASA Technical Reports Server (NTRS)

Ross, R. G., Jr.; Runkle, L. D.

1982-01-01

Photovoltaic-array/power-conditioner interface studies are updated. An experiment conducted to evaluate different operating-point strategies, such as constant voltage and pilot cells, and to determine array energy losses when the array is operated off the maximum power points is described. Initial results over a test period of three and a half weeks showed a 2% energy loss when the array is operated at a fixed voltage. Degraded-array studies conducted at NE RES that used a range of simulated common types of degraded I-V curves are reviewed. The instrumentation installed at the JPL field-test site to obtain the irradiance data was described. Experiments using an optical filter to adjust the spectral irradiance of the large-area pulsed solar simulator (LAPSS) to AM1.5 are described. Residential-array research activity is reviewed. Voltage isolation test results are described. Experiments performed on one type of module to determine the relationship between leakage current and temperature are reviewed. An encapsulated-cell testing approach is explained. The test program, data reduction methods, and initial results of long-duration module testing are described.

Validity of wearable activity monitors for tracking steps and estimating energy expenditure during a graded maximal treadmill test.

PubMed

Kendall, Bradley; Bellovary, Bryanne; Gothe, Neha P

2018-06-04

The purpose of this study was to assess the accuracy of energy expenditure (EE) estimation and step tracking abilities of six activity monitors (AMs) in relation to indirect calorimetry and hand counted steps and assess the accuracy of the AMs between high and low fit individuals in order to assess the impact of exercise intensity. Fifty participants wore the Basis watch, Fitbit Flex, Polar FT7, Jawbone, Omron pedometer, and Actigraph during a maximal graded treadmill test. Correlations, intra-class correlations, and t-tests determined accuracy and agreement between AMs and criterions. The results indicate that the Omron, Fitbit, and Actigraph were accurate for measuring steps while the Basis and Jawbone significantly underestimated steps. All AMs were significantly correlated with indirect calorimetry, however, no devices showed agreement (p < .05). When comparing low and high fit groups, correlations between AMs and indirect calorimetry improved for the low fit group, suggesting AMs may be better at measuring EE at lower intensity exercise.

Utilization of inoculum of AM fungi produced on-farm for the production of Solanum lycopersicum: a summary of 7 years of field trials on a conventional vegetable farm with high soil phosphorus

USDA-ARS?s Scientific Manuscript database

Adding arbuscular mycorrhizal [AM] fungus inoculum to potting media enables vegetable farmers to better take advantage of the AM symbiosis. On-farm production of AM fungus inoculum is a viable alternative to commercially-available inocula. We conducted a seven year experiment at a conventional veg...

KSC-2010-5494

NASA Image and Video Library

2010-11-04

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the Alpha Magnetic Spectrometer-2 (AMS) sits in its cargo element work stand, where technicians will continue to process the experiment for launch. AMS is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch Feb. 27, 2011. Photo credit: NASA/Jack Pfaller

KSC-2010-5493

NASA Image and Video Library

2010-11-04

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the Alpha Magnetic Spectrometer-2 (AMS) sits in its cargo element work stand, where technicians will continue to process the experiment for launch. AMS is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch Feb. 27, 2011. Photo credit: NASA/Jack Pfaller

Sensitivity and validity of psychometric tests for assessing driving impairment: effects of sleep deprivation.

PubMed

Jongen, Stefan; Perrier, Joy; Vuurman, Eric F; Ramaekers, Johannes G; Vermeeren, Annemiek

2015-01-01

To assess drug induced driving impairment, initial screening is needed. However, no consensus has been reached about which initial screening tools have to be used. The present study aims to determine the ability of a battery of psychometric tests to detect performance impairing effects of clinically relevant levels of drowsiness as induced by one night of sleep deprivation. Twenty four healthy volunteers participated in a 2-period crossover study in which the highway driving test was conducted twice: once after normal sleep and once after one night of sleep deprivation. The psychometric tests were conducted on 4 occasions: once after normal sleep (at 11 am) and three times during a single night of sleep deprivation (at 1 am, 5 am, and 11 am). On-the-road driving performance was significantly impaired after sleep deprivation, as measured by an increase in Standard Deviation of Lateral Position (SDLP) of 3.1 cm compared to performance after a normal night of sleep. At 5 am, performance in most psychometric tests showed significant impairment. As expected, largest effect sizes were found on performance in the Psychomotor Vigilance Test (PVT). Large effects sizes were also found in the Divided Attention Test (DAT), the Attention Network Test (ANT), and the test for Useful Field of View (UFOV) at 5 and 11 am during sleep deprivation. Effects of sleep deprivation on SDLP correlated significantly with performance changes in the PVT and the DAT, but not with performance changes in the UFOV. From the psychometric tests used in this study, the PVT and DAT seem most promising for initial evaluation of drug impairment based on sensitivity and correlations with driving impairment. Further studies are needed to assess the sensitivity and validity of these psychometric tests after benchmark sedative drug use.

Results from the XENON10 and the Race to Detect Dark Matter with Noble Liquids

ScienceCinema

Shutt, Tom [Case Western Reserve, Cleveland, Ohio, United States

2017-12-09

Detectors based on liquid noble gases have the potential to revolutionize the direct search for WIMP dark matter. The XENON10 experiment, of which I am a member, has recently announced the results from it's first data run and is now the leading WIMP search experiment. This and other experiments using xenon, argon and neon have the potential to rapidly move from the current kg-scale target mass to the ton scale and well beyond. This should allow a (nearly) definitive test or discovery of dark matter if it is in the form of weakly interacting massive particles.

A&M. Plot plan of administration and A&M areas. Shows relationships ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Plot plan of administration and A&M areas. Shows relationships among administration buildings and to A&M building (TAN-607), railroad turntable. Ralph M. Parsons 902-2&3-ANP-U 3. Date: December 1952. INEEL index code no. 032-0100-00-693-106690 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Nestedness in Arbuscular Mycorrhizal Fungal Communities along Soil pH Gradients in Early Primary Succession: Acid-Tolerant Fungi Are pH Generalists

PubMed Central

Kawahara, Ai; An, Gi-Hong; Miyakawa, Sachie; Sonoda, Jun

2016-01-01

Soil acidity is a major constraint on plant productivity. Arbuscular mycorrhizal (AM) fungi support plant colonization in acidic soil, but soil acidity also constrains fungal growth and diversity. Fungi in extreme environments generally evolve towards specialists, suggesting that AM fungi in acidic soil are acidic-soil specialists. In our previous surveys, however, some AM fungi detected in strongly acidic soils could also be detected in a soil with moderate pH, which raised a hypothesis that the fungi in acidic soils are pH generalists. To test the hypothesis, we conducted a pH-manipulation experiment and also analyzed AM fungal distribution along a pH gradient in the field using a synthesized dataset of the previous and recent surveys. Rhizosphere soils of the generalist plant Miscanthus sinensis were collected both from a neutral soil and an acidic soil, and M. sinensis seedlings were grown at three different pH. For the analysis of field communities, rhizosphere soils of M. sinensis were collected from six field sites across Japan, which covered a soil pH range of 3.0–7.4, and subjected to soil trap culture. AM fungal community compositions were determined based on LSU rDNA sequences. In the pH-manipulation experiment the acidification of medium had a significant impact on the compositions of the community from the neutral soil, but the neutralization of the medium had no effect on those of the community from the acidic soil. Furthermore, the communities in lower -pH soils were subsets of (nested in) those in higher-pH soils. In the field communities a significant nestedness pattern was observed along the pH gradient. These observations suggest that the fungi in strongly acidic soils are pH generalists that occur not only in acidic soil but also in wide ranges of soil pH. Nestedness in AM fungal community along pH gradients may have important implications for plant community resilience and early primary succession after disturbance in acidic soils. PMID:27755574

Nestedness in Arbuscular Mycorrhizal Fungal Communities along Soil pH Gradients in Early Primary Succession: Acid-Tolerant Fungi Are pH Generalists.

PubMed

Kawahara, Ai; An, Gi-Hong; Miyakawa, Sachie; Sonoda, Jun; Ezawa, Tatsuhiro

2016-01-01

Soil acidity is a major constraint on plant productivity. Arbuscular mycorrhizal (AM) fungi support plant colonization in acidic soil, but soil acidity also constrains fungal growth and diversity. Fungi in extreme environments generally evolve towards specialists, suggesting that AM fungi in acidic soil are acidic-soil specialists. In our previous surveys, however, some AM fungi detected in strongly acidic soils could also be detected in a soil with moderate pH, which raised a hypothesis that the fungi in acidic soils are pH generalists. To test the hypothesis, we conducted a pH-manipulation experiment and also analyzed AM fungal distribution along a pH gradient in the field using a synthesized dataset of the previous and recent surveys. Rhizosphere soils of the generalist plant Miscanthus sinensis were collected both from a neutral soil and an acidic soil, and M. sinensis seedlings were grown at three different pH. For the analysis of field communities, rhizosphere soils of M. sinensis were collected from six field sites across Japan, which covered a soil pH range of 3.0-7.4, and subjected to soil trap culture. AM fungal community compositions were determined based on LSU rDNA sequences. In the pH-manipulation experiment the acidification of medium had a significant impact on the compositions of the community from the neutral soil, but the neutralization of the medium had no effect on those of the community from the acidic soil. Furthermore, the communities in lower -pH soils were subsets of (nested in) those in higher-pH soils. In the field communities a significant nestedness pattern was observed along the pH gradient. These observations suggest that the fungi in strongly acidic soils are pH generalists that occur not only in acidic soil but also in wide ranges of soil pH. Nestedness in AM fungal community along pH gradients may have important implications for plant community resilience and early primary succession after disturbance in acidic soils.

Polymorphs and solvatomorphs of azilsartan medoxomil: Elucidation of solvent-induced construction and conformational diversity

NASA Astrophysics Data System (ADS)

Zhang, Xian-Rui; He, Sai-Fei; Zhang, Shuo; Li, Jing; Li, Shan; Liu, Jin-Song; Zhang, Lei

2017-02-01

Two polymorphs (AM-A and AM-B) of azilsartan medoxomil (AM) and four AM solvatomorphs with toluene (AM-TOL), 1,4-dioxane (AM-DIO), chloroform (AM-TCM) and N,N-dimethylacetamide (AM-DMA) have been prepared by the hydrolysis of azilsartan medoxomil potassium in aqueous-organic solutions. In the crystal structures of two polymorphs and three solvatomorphs (AM-TOL, AM-DIO and AM-TCM), two asymmetric AM molecules form the dimeric cycle-like structures via intermolecular Nsbnd H⋯N hydrogen bonds in R22 (26) ring, while AM-DMA shows intramolecular Nsbnd H⋯O hydrogen bond between AM and DMA molecules. The hydrogen bonds (Csbnd H⋯O or Csbnd H⋯N) and π···π (or Csbnd H···π) interactions are helpful to stabilize the conformational diversity of AM. The solvent-induced experiment shows that solvent molecules have great influence on the solvatomorph formation and DIO can form the most steady solvatomorph than other solvents. The thermal study demonstrates that toluene molecules in three solvatomorphs (AM-TOL, AM-DIO and AM-TCM) are the most difficult to remove from the cage. Our results illustrate that the solvent plays significant role in tuning the size of the cage and producing the conformational diversity of AM molecules.

Effects of refrigerating preinoculated Vitek cards on microbial physiology and antibiotic susceptibility

NASA Technical Reports Server (NTRS)

Skweres, Joyce A.; Bassinger, Virginia J.; Mishra, S. K.; Pierson, Duane L.

1992-01-01

Reference cultures of 16 microorganisms obtained from the American Type Culture Collection and four clinical isolates were used in standardized solutions to inoculate 60 cards for each test strain. A set of three ID and three susceptibility cards was processed in the Vitek AutoMicrobic System (AMS) immediately after inoculation. The remaining cards were refrigerated at 4 C, and sets of six cards were removed and processed periodically for up to 17 days. The preinoculated AMS cards were evaluated for microorganism identification, percent probability of correct identification, length of time required for final result, individual substrate reactions, and antibiotic minimal inhibitory/concentration (MIC) values. Results indicate that 11 of the 20 microbes tested withstood refrigerated storage up to 17 days without detectable changes in delineating characteristics. MIC results appear variable, but certain antibiotics proved to be more stable than others. The results of these exploratory studies will be used to plan a microgravity experiment designed to study the effect of microgravity on microbial physiology and antibiotic sensitivity.

Technology Reinvestment Project Manufacturing Education and Training. Volume 1

NASA Technical Reports Server (NTRS)

Schroer, Bernard J.; Bond, Arthur J.

1997-01-01

The manufacturing education program is a joint program between the University of Alabama in Huntsville's (UAH) College of Engineering and Alabama A&M University's (AAMLJ) School of Engineering and Technology. The objective of the program is to provide more hands-on experiences to undergraduate engineering and engineering technology students. The scope of work consisted of. Year 1, Task 1: Review courses at Alabama Industrial Development Training (AIDT); Task 2: Review courses at UAH and AAMU; Task 3: Develop new lab manuals; Task 4: Field test manuals; Task 5: Prepare annual report. Year 2, Task 1: Incorporate feedback into lab manuals; Task 2 : Introduce lab manuals into classes; Task 3: Field test manuals; Task 4: Prepare annual report. Year 3, Task 1: Incorporate feedback into lab manuals; Task 2: Introduce lab manuals into remaining classes; Task 3: Conduct evaluation with assistance of industry; Task 4: Prepare final report. This report only summarizes the activities of the University of Alabama in Huntsville. The activities of Alabama A&M University are contained in a separate report.

Human Milk Adrenomedullin Is Unstable During Cold Storage at 4°C.

PubMed

Peila, Chiara; Coscia, Alessandra; Bertino, Enrico; Li Volti, Giovanni; Galvano, Fabio; Barbagallo, Ignazio; Gazzolo, Diego

2017-11-01

Under some circumstances human milk (HM) extraction and refrigerated storage may be necessary. Depending on the length and on the type of cold storage, milk may lose some important properties, but current advices on safe HM storage are discordant. Moreover until now no data in literature were present on the effect of prolonged cold storage on biologically active components of the HM such as adrenomedullin (AM). This important peptide is involved in response to hypoxia and inflammation, associated with neovascularization, in several tissues. The aim is to evaluate: (a) the presence of AM in preterm and term HM and (b) the concentration of AM in refrigerated milk at 4°C at 24-hour intervals, up to 96 hours of storage. The experiment was repeated four times. Immediately after collection, each HM sample deriving from each mother was divided into two parts as follows: "Pool" line and "Single Mother" line. One part (Pool line) was pooled and then divided into five aliquots. The other part (Single Mother line) was divided into five aliquots. From each line, one aliquot was analyzed within 3 hours, while the others were stored in the refrigerator for 24, 48, 72, and 96 hours, respectively, and then analyzed. AM levels were determined using a specific ELISA test. AM was detectable in all samples. Its concentration was significantly higher in preterm milk with respect to term milk (p < 0.05). Significant differences were observed during the cold storage: the AM levels decreased steadily during the storage and the remaining concentration at 96 hours is ∼2%. This study provides evidences regarding the presence of AM in HM, regardless of the gestational age. In particular, the refrigeration of fresh HM in controlled conditions significantly affected its bioactivity and nutritional quality related with AM, already at 24 hours.

77 FR 26471 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs: 6-acetylmorphine (6-AM...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-04

... 2105-AE14 Procedures for Transportation Workplace Drug and Alcohol Testing Programs: 6-acetylmorphine... Department is amending certain provisions of its drug testing procedures for 6-acetylmorphine (6-AM), a... (email). SUPPLEMENTARY INFORMATION: Background For its drug testing regulation, the Department of...

Sleep disordered breathing and acute mountain sickness in workers rapidly transported to the South Pole (2835 m).

PubMed

Anderson, P J; Wiste, H J; Ostby, S A; Miller, A D; Ceridon, M L; Johnson, B D

2015-05-01

Sleep disordered breathing may be a risk factor for high altitude illness. Past Antarctic sleep studies suggest that rapid transport from sea level (SL) to the Amundsen Scott South Pole Station (SP, 2835 m) increases risk of Acute Mountain Sickness (AMS). We analyzed sleep studies in 38 healthy polar workers to explore the association between sleep disordered breathing and AMS after rapid transport to the South Pole. Subjects completed a baseline questionnaire, performed basic physiology tests, and were evaluated for AMS and medication use using an extended Lake Louise Questionnaire (LLQ) during their first week at the South Pole. Participants were included in this study if they took no medications and underwent polysomnography on their first nights at Sea Level and the South Pole using the Vivometrics LifeShirt(®). Within group changes were assessed with Wilcoxon signed rank tests and between group differences were assessed with Kruskal-Wallis rank sum tests. Overall, 21/38 subjects met criteria for AMS at some time on or prior to the third morning at the South Pole. Subjective poor sleep quality was reported by both AMS (65%) and no AMS (41%) groups. The Apnea Hypopnea Index (AHI) increased significantly in both the AMS and no AMS groups, but the difference in the increase between the two groups was not statistically significant. Increased AHI was not associated with increased AMS symptoms. Previous altitude illness (p=0.06) and residence at low altitudes (p = 0.02) were risk factors for AMS. AMS was not significantly associated with sleep architecture changes or increased AHI. However, AHI sharply increased at South Pole (19/38 participants) primarily due to central apneas. Those developing AMS were more likely to have experienced previous problems at altitude and reported living at lowland altitudes within the 3 months prior to rapid transport to the South Pole than those without AMS. Copyright © 2015 Elsevier B.V. All rights reserved.

In Vitro Dissolution Tests of Plutonium and Americium Containing Contamination Originating From ZPPR Fuel Plates

DOE Office of Scientific and Technical Information (OSTI.GOV)

William F. Bauer; Brian K. Schuetz; Gary M. Huestis

2012-09-01

Assessing the extent of internal dose is of concern whenever workers are exposed to airborne radionuclides or other contaminants. Internal dose determinations depend upon a reasonable estimate of the expected biological half-life of the contaminants in the respiratory tract. One issue with refractory elements is determining the dissolution rate of the element. Actinides such as plutonium (Pu) and Americium (Am) tend to be very refractory and can have biological half-lives of tens of years. In the event of an exposure, the dissolution rates of the radionuclides of interest needs to be assessed in order to assign the proper internal dosemore » estimates. During the November 2011 incident at the Idaho National Laboratory (INL) involving a ZPPR fuel plate, air filters in a constant air monitor (CAM) and a giraffe filter apparatus captured airborne particulate matter. These filters were used in dissolution rate experiments to determine the apparent dissolution half-life of Pu and Am in simulated biological fluids. This report describes these experiments and the results. The dissolution rates were found to follow a three term exponential decay equation. Differences were noted depending upon the nature of the biological fluid simulant. Overall, greater than 95% of the Pu and 93% of the Am were in a very slow dissolving component with dissolution half-lives of over 10 years.« less

Utilization of unconventional lignocellulosic waste biomass for the biosorption of toxic triphenylmethane dye malachite green from aqueous solution.

PubMed

Selvasembian, Rangabhashiyam; P, Balasubramanian

2018-05-12

Biosorption potential of novel lignocellulosic biosorbents Musa sp. peel (MSP) and Aegle marmelos shell (AMS) was investigated for the removal of toxic triphenylmethane dye malachite green (MG), from aqueous solution. Batch experiments were performed to study the biosorption characteristics of malachite green onto lignocellulosic biosorbents as a function of initial solution pH, initial malachite green concentration, biosorbents dosage, and temperature. Biosorption equilibrium data were fitted to two and three parameters isotherm models. Three-parameter isotherm models better described the equilibrium data. The maximum monolayer biosorption capacities obtained using the Langmuir model for MG removal using MSP and AMS was 47.61 and 18.86 mg/g, respectively. The biosorption kinetic data were analyzed using pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models. The pseudo-second-order kinetic model best fitted the experimental data, indicated the MG biosorption using MSP and AMS as chemisorption process. The removal of MG using AMS was found as highly dependent on the process temperature. The removal efficiency of MG showed declined effect at the higher concentrations of NaCl and CaCl 2 . The regeneration test of the biosorbents toward MG removal was successful up to three cycles.

Agency and Error in Young Adults' Stories of Sexual Decision Making

ERIC Educational Resources Information Center

Allen, Katherine R.; Husser, Erica K.; Stone, Dana J.; Jordal, Christian E.

2008-01-01

We conducted a qualitative analysis of 148 college students' written comments about themselves as sexual decision makers. Most participants described experiences in which they were actively engaged in decision-making processes of "waiting it out" to "working it out." The four patterns were (a) I am in control, (b) I am experimenting and learning,…

76 FR 72681 - Proposed Information Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-25

... street address given in paragraph (1) above, between 9 a.m. and 4 p.m. Monday through Friday, except... telecommunications device for the deaf (TTY-TDD) may call 1 (800) 833- 3722 between 8 a.m. and 8 p.m. Eastern Time... participants experience connections to their service experience in order to develop knowledge and refine...

Trivalent Actinide Uptake by Iron (Hydr)oxides.

PubMed

Finck, Nicolas; Nedel, Sorin; Dideriksen, Knud; Schlegel, Michel L

2016-10-04

The retention of Am(III) by coprecipitation with or adsorption onto preformed magnetite was investigated by X-ray diffraction (XRD), solution chemistry, and X-ray absorption spectroscopy (XAS). In the coprecipitation experiment, XAS data indicated the presence of seven O atoms at 2.44(1) Å, and can be explained by an Am incorporation at Fe structural sites at the magnetite surface. Next-nearest Fe were detected at distances suggesting that Am and Fe polyhedra share corners in geometries ranging from bent to close to linear Am-O-Fe bonds. After aging for two years, the coordination number and the distance to the first O shell significantly decreased, and atomic shells were detected at higher distances. These data suggest a structural reorganization and an increase in structural order around sorbed Am. Upon contact with preformed Fe 3 O 4 , Am(III) forms surface complexes with cosorbed Fe at the surface of magnetite, a possible consequence of the high concentration of dissolved Fe. In a separate experiment, chloride green rust (GR) was synthesized in the presence of Am(III), and subsequently converted to Fe(OH) 2 (s) intermixed with magnetite. XAS data indicated that the actinide is successively located first at octahedral brucite-like sites in the GR precursor, then in Fe(OH) 2 (s), an environment markedly distinct from that of Am(III) in Fe 3 O 4 . The findings indicate that the magnetite formation pathway dictates the magnitude of Am(III) incorporation within this solid.

Booster Test for Space Launch System Rocket

NASA Image and Video Library

2016-06-26

The test area where the second and final qualification motor (QM-2) test for the Space Launch System’s booster is seen Sunday, June 26, 2016, at Orbital ATK Propulsion Systems test facilities in Promontory, Utah. The test is scheduled for Tuesday, June 28 at 10:05 a.m. EDT (8:05 a.m. MDT). Photo Credit: (NASA/Bill Ingalls)

The ETA-II induction linac as a high-average-power FEL driver

NASA Astrophysics Data System (ADS)

Nexsen, W. E.; Atkinson, D. P.; Barrett, D. M.; Chen, Y.-J.; Clark, J. C.; Griffith, L. V.; Kirbie, H. C.; Newton, M. A.; Paul, A. C.; Sampayan, S.; Throop, A. L.; Turner, W. C.

1990-10-01

The Experimental Test Accelerator II (ETA-II) is the first induction linac designed specifically to FEL requirements. It is primarily intended to demonstrate induction accelerator technology for high-average-power, high-brightness electron beams, and will be used to drive a 140 and 250 GHz microwave FEL for plasma heating experiments in the Microwave Tokamak Experiment (MTX) at LLNL. Its features include high-vacuum design which allows the use of an intrinsically bright dispenser cathode, induction cells designed to minimize BBU growth rate, and careful attention to magnetic alignment to minimize radial sweep due to beam corkscrew. The use of magnetic switches allows high-average-power operation. At present ETA-II is being used to drive 140 GHz plasma heating experiments. These experiments require nominal beam parameters of 6 MeV energy, 2 kA current, 20 ns pulse width and a brightness of 1 × 108 A/(m rad)2 at the wiggler with a pulse repetition frequency (prf) of 0.5 Hz. Future 250 GHz experiments require beam parameters of 10 MeV energy, 3 kA current, 50 ns pulse width and a brightness of 1 × 108 A/(m rad)2 with a 5 kHz prf for 0.5 s. In this paper we discuss the present status of ETA-II parameters and the phased development program necessary to satisfy these future requirements.

AMS in payload bay viewed from Mir Space Station

NASA Image and Video Library

2016-08-24

STS091-367-033 (2-12 June 1998) --- This photo of the Space Shuttle Discovery's aft section features the Alpha Magnetic Spectrometer (AMS), as seen from Russia's Mir space station, docked with Discovery at the time. AMS is the first large-magnet experiment ever placed in Earth orbit. The scientific goal of this high-energy physics experiment is to increase our understanding of the composition and origin of the universe. It is designed to search for and measure charged particles, including antimatter, outside Earth's atmosphere. The charge of such particles can be identified only by their trajectories in a magnetic field.

Phylogenetic trait conservatism and the evolution of functional trade-offs in arbuscular mycorrhizal fungi.

PubMed

Powell, Jeff R; Parrent, Jeri L; Hart, Miranda M; Klironomos, John N; Rillig, Matthias C; Maherali, Hafiz

2009-12-07

The diversity of functional and life-history traits of organisms depends on adaptation as well as the legacy of shared ancestry. Although the evolution of traits in macro-organisms is well studied, relatively little is known about character evolution in micro-organisms. Here, we surveyed an ancient and ecologically important group of microbial plant symbionts, the arbuscular mycorrhizal (AM) fungi, and tested hypotheses about the evolution of functional and life-history traits. Variation in the extent of root and soil colonization by AM fungi is constrained to a few nodes basal to the most diverse groups within the phylum, with relatively little variation associated with recent divergences. We found no evidence for a trade-off in biomass allocated to root versus soil colonization in three published glasshouse experiments; rather these traits were positively correlated. Partial support was observed for correlated evolution between fungal colonization strategies and functional benefits of the symbiosis to host plants. The evolution of increased soil colonization was positively correlated with total plant biomass and shoot phosphorus content. Although the effect of AM fungi on infection by root pathogens was phylogenetically conserved, there was no evidence for correlated evolution between the extent of AM fungal root colonization and pathogen infection. Variability in colonization strategies evolved early in the diversification of AM fungi, and we propose that these strategies were influenced by functional interactions with host plants, resulting in an evolutionary stasis resembling trait conservatism.

Sorption of Fluorotelomer Sulfonates, Fluorotelomer Sulfonamido Betaines, and a Fluorotelomer Sulfonamido Amine in National Foam Aqueous Film-Forming Foam to Soil.

PubMed

Barzen-Hanson, Krista A; Davis, Shannon E; Kleber, Markus; Field, Jennifer A

2017-11-07

During fire-fighter training, equipment testing, and emergency responses with aqueous film-forming foams (AFFFs), milligrams per liter concentrations of anionic, zwitterionic, and cationic per- and polyfluoroalkyl substances (PFASs) enter the environment. Because the behavior of zwitterionic and cationic PFASs in the subsurface is unknown, batch sorption experiments were conducted using National Foam AFFF, which contains anionic fluorotelomer sulfonates (FtSs), zwitterionic fluorotelomer sulfonamido betaines (FtSaBs), and cationic 6:2 fluorotelomer sulfonamido amine (FtSaAm). Sorption of the FtSs, FtSaBs, and 6:2 FtSaAm to six soils with varying organic carbon, effective cation-exchange capacity, and anion-exchange capacity was evaluated to determine sorption mechanisms. Due to the poor recovery of the FtSaBs and 6:2 FtSaAm with published PFAS soil extraction methods, a new soil extraction method was developed to achieve good (90-100%) recoveries. The 6:2 FtSaAm was depleted from the aqueous phase in all but one soil, which is attributed to electrostatic and hydrophobic interactions. Sorption of the FtSs was driven by hydrophobic interactions, while the FtSaBs behave more like cations that strongly associate with the solid phase relative to groundwater. Thus, the sorption mechanisms of the FtSs, FtSaBs, and 6:2 FtSaAm are more complex than expected and cannot be predicted by bulk soil properties.

Time reversal through a solid-liquid interface and super-resolution

NASA Astrophysics Data System (ADS)

Tsogka, Chrysoula; Papanicolaou, George C.

2002-12-01

We present numerical computations that reproduce the time-reversal experiments of Draeger et al (Draeger C, Cassereau D and Fink M 1998 Appl. Phys. Lett. 72 1567-9), where ultrasound elastic waves are time-reversed back to their source with a time-reversal mirror in a fluid adjacent to the solid. We also show numerically that multipathing caused by random inhomogeneities improves the focusing of the back-propagated elastic waves beyond the diffraction limit seen previously in acoustic wave propagation (Dowling D R and Jackson D R 1990 J. Acoust. Soc. Am. 89 171-81, Dowling D R and Jackson D R 1992 J. Acoust. Soc. Am. 91 3257-77, Fink M 1999 Sci. Am. 91-7, Kuperman W A, Hodgkiss W S, Song H C, Akal T, Ferla C and Jackson D R 1997 J. Acoust. Soc. Am. 103 25-40, Derode A, Roux P and Fink M 1995 Phys. Rev. Lett. 75 4206-9), which is called super-resolution. A theoretical explanation of the robustness of super-resolution is given, along with several numerical computations that support this explanation (Blomgren P, Papanicolaou G and Zhao H 2002 J. Acoust. Soc. Am. 111 238-48). Time reversal with super-resolution can be used in non-destructive testing and, in a different way, in imaging with active arrays (Borcea L, Papanicolaou G, Tsogka C and Berryman J 2002 Inverse Problems 18 1247-79).

On-line I-/Te- separation for the AMS analysis of 125I

NASA Astrophysics Data System (ADS)

Charles, C. R. J.; Cornett, R. J.; Zhao, X.-L.; Litherland, A. E.; Kieser, W. E.

2015-10-01

The isobar separator for anions (ISA) was used together with a 3 MV tandem accelerator mass spectrometer (AMS) to demonstrate the real time (on-line) separation of Te- from I-. Following the ion source mass spectrometry and major retardation to tens of eV, the ISA uses a radiofrequency quadrupole (RFQ) ion guide to confine and direct I- and associated Te- isobar anions through a gas-reaction cell, where chemical reactions occur at eV energies with the electronegative gas NO2. Anions are subsequently reaccelerated out of the ISA to near original ion source extraction energies for AMS analysis. At 5 mTorr NO2 in the ISA gas-reaction cell, 125Te- was observed to be attenuated by a factor of ∼107 as compared to 127I- that did not experience significant (<50%) losses. A comparative test using 37Cl- and 32S- (having similar chemical properties to iodine and tellurium) showed a 32S- attenuation of >107 relative to 37Cl- under the same ISA-AMS conditions. The preferential destruction of Te- (and S-) at eV energies in the ISA is likely due to a larger favorable destruction cross-section with NO2. This study is the first demonstration of I-Te anion separation for AMS, and makes possible the use of 125I, free of the contaminant 125Te isobar after suitable sample purification, for future 129I/125I carrier-free analyses of natural samples at ultra-low trace levels.

Interactions between amplitude modulation and frequency modulation processing: Effects of age and hearing loss.

PubMed

Paraouty, Nihaad; Ewert, Stephan D; Wallaert, Nicolas; Lorenzi, Christian

2016-07-01

Frequency modulation (FM) and amplitude modulation (AM) detection thresholds were measured for a 500-Hz carrier frequency and a 5-Hz modulation rate. For AM detection, FM at the same rate as the AM was superimposed with varying FM depth. For FM detection, AM at the same rate was superimposed with varying AM depth. The target stimuli always contained both amplitude and frequency modulations, while the standard stimuli only contained the interfering modulation. Young and older normal-hearing listeners, as well as older listeners with mild-to-moderate sensorineural hearing loss were tested. For all groups, AM and FM detection thresholds were degraded in the presence of the interfering modulation. AM detection with and without interfering FM was hardly affected by either age or hearing loss. While aging had an overall detrimental effect on FM detection with and without interfering AM, there was a trend that hearing loss further impaired FM detection in the presence of AM. Several models using optimal combination of temporal-envelope cues at the outputs of off-frequency filters were tested. The interfering effects could only be predicted for hearing-impaired listeners. This indirectly supports the idea that, in addition to envelope cues resulting from FM-to-AM conversion, normal-hearing listeners use temporal fine-structure cues for FM detection.

Endocannabinoid signaling is required for development and critical period plasticity of the whisker map in somatosensory cortex

PubMed Central

Li, Lu; Bender, Kevin J.; Drew, Patrick J.; Jadhav, Shantanu P.; Sylwestrak, Emily; Feldman, Daniel E.

2009-01-01

Summary Type 1 cannabinoid (CB1) receptors mediate widespread synaptic plasticity, but how this contributes to systems-level plasticity and development in vivo is unclear. We tested whether CB1 signaling is required for development and plasticity of the whisker map in rat somatosensory cortex. Treatment with the CB1 antagonist AM251 during an early critical period for layer (L) 2/3 development (beginning postnatal day [P] 12–16) disrupted whisker map development, leading to inappropriate whisker tuning in L2/3 column edges and a blurred map. Early AM251 treatment also prevented experience-dependent plasticity in L2/3, including deprivation-induced synapse weakening and weakening of deprived whisker responses. CB1 blockade after P25 did not disrupt map development or plasticity. AM251 had no acute effect on sensory-evoked spiking, and only modestly affected field potentials, suggesting that plasticity effects were not secondary to gross activity changes. These findings implicate CB1-dependent plasticity in systems-level development and early postnatal plasticity of the whisker map. PMID:19945395

Using Case Studies in Calculus-based Physics

NASA Astrophysics Data System (ADS)

Katz, Debora M.

2006-12-01

Do your students believe that the physics only works in your classroom or laboratory? Or do they see that physics underlies their everyday experience? Case studies in physics help students connect physics principles to their everyday experience. For decades, case studies have been used to teach law, medicine and biology, but they are rarely used in physics. I am working on a calculus-based physics textbook for scientists and engineers. Case studies are woven into each chapter. Stop by and get a case study to test out in your classroom. I would love to get your feedback.

Multisite analytical evaluation of the Abbott ARCHITECT cyclosporine assay.

PubMed

Wallemacq, Pierre; Maine, Gregory T; Berg, Keith; Rosiere, Thomas; Marquet, Pierre; Aimo, Giuseppe; Mengozzi, Giulio; Young, Julianna; Wonigeit, Kurt; Kretschmer, Robert; Wermuth, Bendicht; Schmid, Rainer W

2010-04-01

The objective of this study was to evaluate the analytical performance of the Abbott ARCHITECT Cyclosporine (CsA) immunoassay in 7 clinical laboratories in comparison to liquid chromatography/tandem mass spectrometry (LC/MS/MS), Abbott TDx, Cobas Integra 800, and the Dade Dimension Xpand immunoassay. The ARCHITECT assay uses a whole blood specimen, a pretreatment step with organic reagents to precipitate proteins and extract the drug, followed by a 2-step automated immunoassay with magnetic microparticles coated with anti-CsA antibody and an acridinium-CsA tracer. Imprecision testing at the 7 evaluation sites gave a range of total % coefficient of variations of 7.5%-12.2% at 87.5 ng/mL, 6.6%-14.3% at 411 ng/mL, and 5.2%-10.7% at 916 ng/mL. The lower limit of quantification ranged from 12 to 20 ng/mL. Purified CsA metabolites AM1, AM1c, AM4N, AM9, and AM19 were tested in whole blood by the ARCHITECT assay and showed minimal cross-reactivity at all 7 sites. In particular, AM1 and AM9 cross-reactivity in the ARCHITECT assay, ranged from -2.5% to 0.2% and -0.8% to 2.2%, respectively, and was significantly lower than for the TDx assay, in which the values were 3.2% and 16.1%, respectively. Comparable testing of metabolites in the Dade Dimension Xpand assay at 2 evaluation sites showed cross-reactivity to AM4N (6.4% and 6.8%) and AM9 (2.6% and 3.6%) and testing on the Roche Integra 800 showed cross-reactivity to AM1c (2.4%), AM9 (10.7%), and AM19 (2.8%). Cyclosporine International Proficiency Testing Scheme samples, consisting of both pooled specimens from patients receiving CsA therapy as well as whole-blood specimens supplemented with CsA, were tested by the ARCHITECT assay at 6 sites and showed an average bias of -24 to -58 ng/mL versus LC/MSMS CsA and -2 to -37 ng/mL versus AxSYM CsA. Studies were performed with the ARCHITECT CsA assay on patient specimens with the following results: ARCHITECT CsA assay versus LC/MSMS, average bias of 31 ng/mL; ARCHITECT versus the Dade Dimension assay (4 sites), average biases of -7 to -228 ng/mL; ARCHITECT versus AxSYM and TDx, average biases of -4 and -53 ng/mL, respectively. Spearman correlation coefficients were >or=0.89. The ARCHITECT CsA assay has significantly reduced CsA metabolite interference relative to other immunoassays and is a convenient and sensitive semiautomated method to measure CsA in whole blood.

77 FR 67239 - National Organic Program; Periodic Residue Testing

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-09

... genetically modified organisms (GMOs). AMS does not intend for the testing conducted under section 205.670 to..., but not limited to, pesticides, hormones, antibiotics, and GMOs. AMS notes that, under section 205.671...

Neurometric amplitude-modulation detection threshold in the guinea-pig ventral cochlear nucleus

PubMed Central

Sayles, Mark; Füllgrabe, Christian; Winter, Ian M

2013-01-01

Amplitude modulation (AM) is a pervasive feature of natural sounds. Neural detection and processing of modulation cues is behaviourally important across species. Although most ecologically relevant sounds are not fully modulated, physiological studies have usually concentrated on fully modulated (100% modulation depth) signals. Psychoacoustic experiments mainly operate at low modulation depths, around detection threshold (∼5% AM). We presented sinusoidal amplitude-modulated tones, systematically varying modulation depth between zero and 100%, at a range of modulation frequencies, to anaesthetised guinea-pigs while recording spikes from neurons in the ventral cochlear nucleus (VCN). The cochlear nucleus is the site of the first synapse in the central auditory system. At this locus significant signal processing occurs with respect to representation of AM signals. Spike trains were analysed in terms of the vector strength of spike synchrony to the amplitude envelope. Neurons showed either low-pass or band-pass temporal modulation transfer functions, with the proportion of band-pass responses increasing with increasing sound level. The proportion of units showing a band-pass response varies with unit type: sustained chopper (CS) > transient chopper (CT) > primary-like (PL). Spike synchrony increased with increasing modulation depth. At the lowest modulation depth (6%), significant spike synchrony was only observed near to the unit's best modulation frequency for all unit types tested. Modulation tuning therefore became sharper with decreasing modulation depth. AM detection threshold was calculated for each individual unit as a function of modulation frequency. Chopper units have significantly better AM detection thresholds than do primary-like units. AM detection threshold is significantly worse at 40 dB vs. 10 dB above pure-tone spike rate threshold. Mean modulation detection thresholds for sounds 10 dB above pure-tone spike rate threshold at best modulation frequency are (95% CI) 11.6% (10.0–13.1) for PL units, 9.8% (8.2–11.5) for CT units, and 10.8% (8.4–13.2) for CS units. The most sensitive guinea-pig VCN single unit AM detection thresholds are similar to human psychophysical performance (∼3% AM), while the mean neurometric thresholds approach whole animal behavioural performance (∼10% AM). PMID:23629508

Mycorrhizal fungi enhance plant nutrient acquisition and modulate nitrogen loss with variable water regimes.

PubMed

Bowles, Timothy M; Jackson, Louise E; Cavagnaro, Timothy R

2018-01-01

Climate change will alter both the amount and pattern of precipitation and soil water availability, which will directly affect plant growth and nutrient acquisition, and potentially, ecosystem functions like nutrient cycling and losses as well. Given their role in facilitating plant nutrient acquisition and water stress resistance, arbuscular mycorrhizal (AM) fungi may modulate the effects of changing water availability on plants and ecosystem functions. The well-characterized mycorrhizal tomato (Solanum lycopersicum L.) genotype 76R (referred to as MYC+) and the mutant mycorrhiza-defective tomato genotype rmc were grown in microcosms in a glasshouse experiment manipulating both the pattern and amount of water supply in unsterilized field soil. Following 4 weeks of differing water regimes, we tested how AM fungi affected plant productivity and nutrient acquisition, short-term interception of a 15NH4+ pulse, and inorganic nitrogen (N) leaching from microcosms. AM fungi enhanced plant nutrient acquisition with both lower and more variable water availability, for instance increasing plant P uptake more with a pulsed water supply compared to a regular supply and increasing shoot N concentration more when lower water amounts were applied. Although uptake of the short-term 15NH4+ pulse was higher in rmc plants, possibly due to higher N demand, AM fungi subtly modulated NO3- leaching, decreasing losses by 54% at low and high water levels in the regular water regime, with small absolute amounts of NO3- leached (<1 kg N/ha). Since this study shows that AM fungi will likely be an important moderator of plant and ecosystem responses to adverse effects of more variable precipitation, management strategies that bolster AM fungal communities may in turn create systems that are more resilient to these changes. © 2017 John Wiley & Sons Ltd.

Sensitivity and Validity of Psychometric Tests for Assessing Driving Impairment: Effects of Sleep Deprivation

PubMed Central

Jongen, Stefan; Perrier, Joy; Vuurman, Eric F.; Ramaekers, Johannes G.; Vermeeren, Annemiek

2015-01-01

Objective To assess drug induced driving impairment, initial screening is needed. However, no consensus has been reached about which initial screening tools have to be used. The present study aims to determine the ability of a battery of psychometric tests to detect performance impairing effects of clinically relevant levels of drowsiness as induced by one night of sleep deprivation. Methods Twenty four healthy volunteers participated in a 2-period crossover study in which the highway driving test was conducted twice: once after normal sleep and once after one night of sleep deprivation. The psychometric tests were conducted on 4 occasions: once after normal sleep (at 11 am) and three times during a single night of sleep deprivation (at 1 am, 5 am, and 11 am). Results On-the-road driving performance was significantly impaired after sleep deprivation, as measured by an increase in Standard Deviation of Lateral Position (SDLP) of 3.1 cm compared to performance after a normal night of sleep. At 5 am, performance in most psychometric tests showed significant impairment. As expected, largest effect sizes were found on performance in the Psychomotor Vigilance Test (PVT). Large effects sizes were also found in the Divided Attention Test (DAT), the Attention Network Test (ANT), and the test for Useful Field of View (UFOV) at 5 and 11 am during sleep deprivation. Effects of sleep deprivation on SDLP correlated significantly with performance changes in the PVT and the DAT, but not with performance changes in the UFOV. Conclusion From the psychometric tests used in this study, the PVT and DAT seem most promising for initial evaluation of drug impairment based on sensitivity and correlations with driving impairment. Further studies are needed to assess the sensitivity and validity of these psychometric tests after benchmark sedative drug use. PMID:25668292

Near minimum-time maneuvers of the advanced space structures technology research experiment (ASTREX) test article: Theory and experiments

NASA Technical Reports Server (NTRS)

Vadali, Srinivas R.; Carter, Michael T.

1994-01-01

The Phillips Laboratory at the Edwards Air Force Base has developed the Advanced Space Structures Technology Research Experiment (ASTREX) facility to serve as a testbed for demonstrating the applicability of proven theories to the challenges of spacecraft maneuvers and structural control. This report describes the work performed on the ASTREX test article by Texas A&M University under contract NAS119373 as a part of the Control-Structure Interaction (CSI) Guest Investigator Program. The focus of this work is on maneuvering the ASTREX test article with compressed air thrusters that can be throttled, while attenuating structural excitation. The theoretical foundation for designing the near minimum-time thrust commands is based on the generation of smooth, parameterized optimal open-loop control profiles, and the determination of control laws for final position regulation and tracking using Lyapunov stability theory. Details of the theory, mathematical modeling, model updating, and compensation for the presence of 'real world' effects are described and the experimental results are presented. The results show an excellent match between theory and experiments.

Proceedings of the Conference on the Design of Experiments in Army Research Development and Testing (4th) Held in Natick, Massachusetts on October 22-24, 1958

DTIC Science & Technology

1959-08-01

quality evaluation. Biometrics, 9, 22-38 (1953). 12. Campbell, W.I.P. and Blakeslee, A.F. Would a rose smell so sweet by any other name? Horticulture ... Therapeutics , 65, 275-280 (1939). 35. Scheffe, H. An analysis of variance for paired comparisons. J. Am., Stat. Assoc., 47, 381-4oo (1952). 36. Youden, W.J

KSC-02pd1926

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- STS-107 Payload Specialist Ilan Ramon, the first Israeli astronaut, participates in Terminal Countdown Demonstration Test activities, a standard part of Shuttle launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

Studies on the Mechanism of Action of the ’in vitro’ PGB Sub x Effect. 4. The Effect of Order of Addition of PGB Sub x to Assay System.

DTIC Science & Technology

1981-10-16

not cond. totewn endlersment by the Govermeont wrdothey coey orimply the leeneeor rigt @ o Am h products APPROVED BY: DATE: ___________ CDR USN...favorable results from only a few animal experiments (4, 5, 6, 7, 8, 9, 10). Obviously before any human trials may be undertaken much more animal testing must

Combined alcohol and energy drink use: hedonistic motives, adenosine, and alcohol dependence.

PubMed

Marczinski, Cecile A

2014-07-01

Consumption of alcohol mixed with energy drinks (AmED) has been associated with both short- and long-term risks beyond those observed with alcohol alone. AmED use has been associated with heavy episodic (binge) drinking, risky behaviors, and risk of alcohol dependence. Laboratory research has demonstrated that AmED beverages lead to greater motivation to drink versus the same amount of alcohol consumed alone. However, the reason consumers find AmED beverages particularly appealing has been unclear. A recent report by Droste and colleagues (Alcohol Clin Exp Res 2014; 38:2087-2095) is the first study to investigate motivations related to AmED consumption and to determine which motives predict AmED consumption patterns, experience of drinking-related harms, and risk of alcohol dependence. The findings of this study significantly enhance our understanding of why AmED consumption is related to the risk of alcohol dependence and change our understanding of why consumers choose AmED beverages. The authors report that hedonistic motives strongly predicted AmED use and the harms associated with use. While intoxication-reduction motives predicted self-reported accidents and injuries, these motives did not predict AmED consumption patterns and risk of dependence. The risk of alcohol dependence may arise from repeated experiences when drinking alcohol is more pleasurable when energy drinks are consumed with the alcohol. This commentary will focus on why energy drinks might increase the rewarding properties of alcohol in social drinkers. In addition, discussion is provided explaining why more research on the neurotransmitter, adenosine, may actually inform us about the mechanisms contributing to the development of alcohol dependence. Copyright © 2014 by the Research Society on Alcoholism.

Enabling Technologies for Entrepreneurial Opportunities in 3D printing of SmallSats

NASA Technical Reports Server (NTRS)

Kwas, Andrew; MacDonald, Eric; Muse, Dan; Wicker, Ryan; Kief, Craig; Aarestad, Jim; Zemba, Mike; Marshall, Bill; Tolbert, Carol; Connor, Brett

2014-01-01

A consortium of innovative experts in additive manufacturing (AM) comprising Northrup Grumman Technical Services, University of Texas at El Paso (UTEP), Configurable Space Microsystems Innovations & Applications Center (COSMIAC), NASA Glenn Research Center (GRC), and Youngstown State University, have made significant breakthroughs in the goal of creating the first complete 3D printed small satellite. Since AM machines are relatively inexpensive, this should lead to many entrepreneurial opportunities for the small satellite community. Our technology advancements are focused on the challenges of embedding key components within the structure of the article. We have demonstrated, using advanced fused deposition modeling techniques, complex geometric shapes which optimize the spacecraft design. The UTEP Keck Center has developed a method that interrupts the printing process to insert components into specific cavities, resulting in a spacecraft that has minimal internal space allocated for what traditionally were functional purposes. This allows us to increase experiment and instrument capability by provided added volume in a confined small satellite space. Leveraging initial progress made on a NASA contract, the team investigated the potential of new materials that exploit the AM process, producing candidate compositions that exceed the capabilities of traditional materials. These "new materials" being produced and tested include some that have improved radiation shielding, increased permeability, enhanced thermal properties, better conductive properties, and increased structural performance. The team also investigated materials that were previously not possible to be made. Our testing included standard mechanical tests such as vibration, tensile, thermal cycling, and impact resistance as well as radiation and electromagnetic tests. The initial results of these products and their performance will be presented and compared with standard properties. The new materials with the highest probability to disrupt the future of small satellite systems by driving down costs will be highlighted, in conjunction with the electronic embedding process.

241Am (n,gamma) isomer ratio measurement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bond, Evelyn M; Vieira, David J; Moody, Walter A

The objective of this project is to improve the accuracy of the {sup 242}Cm/{sup 241}Am radiochemistry ratio. We have performed an activation experiment to measure the {sup 241}Am(n,{gamma}) cross section leading to either the ground state of {sup 242g}Am (t{sub 1/2} = 16 hr) which decays to {sup 242}Cm (t{sub 1/2} = 163 d) or the long-lived isomer {sup 242m}Am (t{sub 1/2} = 141 yr). This experiment will develop a new set of americium cross section evaluations that can be used with a measured {sup 242}Cm/{sup 241}Am radiochemical measurement for nuclear forensic purposes. This measurement is necessary to interpret themore » {sup 242}Cm/{sup 241}Am ratio because a good measurement of this neutron capture isomer ratio for {sup 241}Am does not exist. The targets were prepared in 2007 from {sup 241}Am purified from LANL stocks. Gold was added to the purified {sup 241}Am as an internal neutron fluence monitor. These targets were placed into a holder, packaged, and shipped to Forschungszentrum Karlsruhe, where they were irradiated at their Van de Graff facility in February 2008. One target was irradiated with {approx}25 keV quasimonoenergetic neutrons produced by the {sup 7}Li(p,n) reaction for 3 days and a second target was also irradiated for 3 days with {approx}500 keV neutrons. Because it will be necessary to separate the {sup 242}Cm from the {sup 241}Am in order to measure the amount of {sup 242}Cm by alpha spectrometry, research into methods for americium/curium separations were conducted concurrently. We found that anion exchange chromatography in methanol/nitric acid solutions produced good separations that could be completed in one day resulting in a sample with no residue. The samples were returned from Germany in July 2009 and were counted by gamma spectrometry. Chemical separations have commenced on the blank sample. Each sample will be spiked with {sup 244}Cm, dissolved and digested in nitric acid solutions. One third of each sample will be processed at a time. First, the gold will be removed by anion exchange chromatography. Then the {sup 242}Cm will be separated from the {sup 241}Am using the methanol/nitric acid anion exchange method. When a sufficient separation has been achieved, a deposit will be prepared and the {sup 242}Cm will be counted by alpha spectrometry. The purified {sup 241}Am fraction containing the long lived {sup 242m}Am will be allowed to decay into {sup 242}Cm for a period of {approx}6 months. After this time, the americium/curium separations will be repeated and the {sup 242}Cm that has grown in will be counted by alpha spectrometry. At the conclusion of the experiment, we will have cross section measurements for {sup 241}Am (n,{gamma}) {sup 242g}Am and {sup 241}Am (n,V) {sup 242m}Am at two energies.« less

Gender differences in autobiographical memory for everyday events: retrieval elicited by SenseCam images versus verbal cues.

PubMed

St Jacques, Peggy L; Conway, Martin A; Cabeza, Roberto

2011-10-01

Gender differences are frequently observed in autobiographical memory (AM). However, few studies have investigated the neural basis of potential gender differences in AM. In the present functional MRI (fMRI) study we investigated gender differences in AMs elicited using dynamic visual images vs verbal cues. We used a novel technology called a SenseCam, a wearable device that automatically takes thousands of photographs. SenseCam differs considerably from other prospective methods of generating retrieval cues because it does not disrupt the ongoing experience. This allowed us to control for potential gender differences in emotional processing and elaborative rehearsal, while manipulating how the AMs were elicited. We predicted that males would retrieve more richly experienced AMs elicited by the SenseCam images vs the verbal cues, whereas females would show equal sensitivity to both cues. The behavioural results indicated that there were no gender differences in subjective ratings of reliving, importance, vividness, emotion, and uniqueness, suggesting that gender differences in brain activity were not due to differences in these measures of phenomenological experience. Consistent with our predictions, the fMRI results revealed that males showed a greater difference in functional activity associated with the rich experience of SenseCam vs verbal cues, than did females.

DEEP: Discover, Explore, and Enjoy Physics & Engineering via High Impact Educational Experiences at Texas A&M and Beyond

NASA Astrophysics Data System (ADS)

Erukhimova, Tatiana; Fry, Edward

2014-03-01

We will present the first results of an innovative program at Texas A&M University that aims to enhance the learning and research experiences of undergraduate and graduate students through their participation in high-profile outreach activities: principally the Texas A&M Physics and Engineering Festival and the Physics Shows. The goals are to enhance students' knowledge of fundamental physics concepts through collaborative hands-on research and educational activities, to teach them effective communication skills and responsibility, and to enhance their opportunities for interactions with their peers and professors outside the classroom. The program activities include (i) students working side-by-side with their peers and professors on research, concept, design, and fabrication of physics demonstration experiments, (ii) presentation of these exhibits during the Festival and Shows in teams of several students and faculty members, (iii) assessment of students teamwork, and (iv) incorporation of new demonstrations in core curriculum classes. Texas A&M Physics and Engineering Festival is a major annual outreach event at TAMU attracting over 4000 visitors and featuring over 100 interactive exhibits, public lectures by prominent scientists, and various hands-on activities. This program is supported by Tier One Grant from Texas A&M University.

Column strength of magnesium alloy AM-57S

NASA Technical Reports Server (NTRS)

Holt, M

1942-01-01

Tests were made to determine the column strength of extruded magnesium alloy AM-57S. Column specimens were tested with round ends and with flat ends. It was found that the compressive properties should be used in computations for column strengths rather than the tensile properties because the compressive yield strength was approximately one-half the tensile yield strength. A formula for the column strength of magnesium alloy AM-57S is given.

Booster Test for Space Launch System Rocket

NASA Image and Video Library

2016-06-26

The test area where the second and final qualification motor (QM-2) test for the Space Launch System’s booster is seen through the window of a camera bunker, Sunday, June 26, 2016, at Orbital ATK Propulsion Systems test facilities in Promontory, Utah. The test is scheduled for Tuesday, June 28 at 10:05 a.m. EDT (8:05 a.m. MDT). Photo Credit: (NASA/Bill Ingalls)

Specificity in autobiographical memory narratives correlates with performance on the Autobiographical Memory Test and prospectively predicts depressive symptoms

PubMed Central

Sumner, Jennifer A.; Mineka, Susan; McAdams, Dan P.

2012-01-01

Reduced autobiographical memory specificity (AMS) is an important cognitive marker in depression that is typically measured with the Autobiographical Memory Test (AMT; Williams & Broadbent, 1986). The AMT is widely used, but the overreliance on a single methodology for assessing AMS is a limitation in the field. The current study investigated memory narratives as an alternative measure of AMS in an undergraduate student sample selected for being high or low on a measure of depressive symptoms (N = 55). We employed a multi-method design to compare narrative- and AMT-based measures of AMS. Participants generated personally significant self-defining memory narratives, and also completed two versions of the AMT (with and without instructions to retrieve specific memories). Greater AMS in self-defining memory narratives correlated with greater AMS in performance on both versions of the AMT in the full sample, and the patterns of relationships between the different AMS measures were generally similar in low and high dysphoric participants. Furthermore, AMS in self-defining memory narratives was prospectively associated with depressive symptom levels. Specifically, greater AMS in self-defining memory narratives predicted fewer depressive symptoms at a 10-week follow-up over and above baseline symptom levels. Implications for future research and clinical applications are discussed. PMID:23240988

Specificity in autobiographical memory narratives correlates with performance on the autobiographical memory test and prospectively predicts depressive symptoms.

PubMed

Sumner, Jennifer A; Mineka, Susan; McAdams, Dan P

2013-01-01

Reduced autobiographical memory specificity (AMS) is an important cognitive marker in depression that is typically measured with the Autobiographical Memory Test (AMT; Williams & Broadbent, 1986). The AMT is widely used, but the over-reliance on a single methodology for assessing AMS is a limitation in the field. The current study investigated memory narratives as an alternative measure of AMS in an undergraduate student sample selected for being high or low on a measure of depressive symptoms (N=55). We employed a multi-method design to compare narrative- and AMT-based measures of AMS. Participants generated personally significant self-defining memory narratives, and also completed two versions of the AMT (with and without instructions to retrieve specific memories). Greater AMS in self-defining memory narratives correlated with greater AMS in performance on both versions of the AMT in the full sample, and the patterns of relationships between the different AMS measures were generally similar in low and high dysphoric participants. Furthermore, AMS in self-defining memory narratives was prospectively associated with depressive symptom levels. Specifically, greater AMS in self-defining memory narratives predicted fewer depressive symptoms at a 10-week follow-up over and above baseline symptom levels. Implications for future research and clinical applications are discussed.

Enhancement of amphotericin B activity against Candida albicans by superoxide radical.

PubMed

Okamoto, Yuichi; Aoki, Shigeji; Mataga, Izumi

2004-07-01

This study aimed to examine the involvement of oxidative damage in amphotericin B (AmB) activity against Candida albicans using the superoxide (O2-) generator paraquat (PQ). The effects of PQ on AmB activities against growth, viability, membrane permeability and respiration were examined in a wild-type parent strain (K) and a respiration-deficient mutant (KRD-19) since PQ-induced superoxide generation depends on respiration. In the parent strain, the minimal inhibitory concentration (MIC) of AmB, 0.25 microg/ml, tested with a liquid culture was lowered to 0.025 microg/ml by 1 mM PQ. Such a PQ-induced decrease in the MIC value of AmB was minimal in the mutant. Similar PQ-induced enhancement of AmB activity toward the parent strain was also observed with growth on an agar medium. In viability tests, when candidal cells were exposed to AmB (0.1 microg/ml) for I h, the lethality of AmB was enhanced by 1 mM PQ only in the parent strain. Exogenous superoxide dismutase and catalase failed to diminish the enhancing effect of PQ on the growth inhibitory activity of AmB in the parent strain, suggesting an interaction between superoxide and AmB in candidal cells. The enhancement of AmB activity by PQ, observed preferentially in the wild-type strain, can be explained by extensive superoxide generation depending on respiration. These results suggest that oxidative damage induced by superoxide is involved in AmB activity against C. albicans.

Overview Of The U.S. Cotton Classification System and a Comparison of the U.S. and Chinese Cotton Classing Parameters

USDA-ARS?s Scientific Manuscript database

All U.S. cotton bales are classed by the Cotton Division of the Agriculture Marketing Service (AMS) of the United States Department of Agriculture. Since 1991, more than 220 million bales have been tested by AMS. AMS has 12 classing offices with 290 High Volume Instruments (HVI). AMS has various ...

Family Experiences of Transition from Child Care to School.

ERIC Educational Resources Information Center

Elliott, Alison

A study traced the experiences of Australian working families as their children started formal schooling. Each family faced the prospect of moving their child or children from the intimate environment of a child care center that operated from 8 a.m. to 6 p.m. to a large elementary school with a 9 a.m. to 3 p.m. school day. The study focused on:…

Cosmic ray strangelets

NASA Astrophysics Data System (ADS)

Madsen, Jes

2005-06-01

Searching for strangelets in cosmic rays may be the best way to test the possible stability of strange quark matter. I review calculations of the astrophysical strangelet flux in the GV TV rigidity range, which will be investigated from the Alpha Magnetic Spectrometer (AMS-02) on the International Space Station, and discuss the merits of strangelets as ultra-high energy cosmic rays at EeV ZeV energies, beyond the Greisen Zatsepin Kuzmin cutoff. I also address some 'counter-arguments' sometimes raised against the possibility of stable strangelets. It will be argued that stability of strange quark matter remains a viable possibility, which must be tested by experiments.

Proceedings of the Conference on the Design of Experiments in Army Research Development and Testing (35th) Held in Monterey California, California on 18-20 October 1989

DTIC Science & Technology

1990-08-01

Statistics. John Wiley and Sons , 1980, p. 111. 7. Hanson, D. L. and Koopmans, Lo H.t Tolerance Limits for the Class of Distributions With Increasing...Am. Statis° Assoc., vol. 82, 1987, p. 918. 9. Lehmann, E0 Lot Testing Statistical Hypotheses. John Wiley and Sons , 1959, pp. 274-275. 10. Lemon, G. H...Surfaces," John Wily & Sons , Inc., New York. 3. Box, G. E. P. and Wilson, K. B. (1951), "On the Experimental Attainment of Optimum Conditions," Journal of

A&M. Jet engine test building (TAN609). Exterior. Equipment inside rollup ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Jet engine test building (TAN-609). Exterior. Equipment inside roll-up door is blowdown test facility, part of loft-semiscale program. Note width of central section serving as blast protection for operator on left side. Photographer: Cahoon. Date: July 22, 1965. INEEL negative no. 65-3703 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

30 CFR 250.524 - When am I required to take action from my casing diagnostic test?

Code of Federal Regulations, 2010 CFR

2010-07-01

... casing diagnostic test; (c) Any well that has demonstrated tubing/casing, tubing/riser, casing/casing... casing diagnostic test? 250.524 Section 250.524 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT... Gas Well-Completion Operations Casing Pressure Management § 250.524 When am I required to take action...

Aerodynamic and Aeroacoustic Wind Tunnel Testing of the Orion Spacecraft

NASA Technical Reports Server (NTRS)

Ross, James C.

2011-01-01

The Orion aerodynamic testing team has completed more than 40 tests as part of developing the aerodynamic and loads databases for the vehicle. These databases are key to achieving good mechanical design for the vehicle and to ensure controllable flight during all potential atmospheric phases of a mission, including launch aborts. A wide variety of wind tunnels have been used by the team to document not only the aerodynamics but the aeroacoustic environment that the Orion might experience both during nominal ascents and launch aborts. During potential abort scenarios the effects of the various rocket motor plumes on the vehicle must be accurately understood. The Abort Motor (AM) is a high-thrust, short duration motor that rapidly separates Orion from its launch vehicle. The Attitude Control Motor (ACM), located in the nose of the Orion Launch Abort Vehicle, is used for control during a potential abort. The 8 plumes from the ACM interact in a nonlinear manner with the four AM plumes which required a carefully controlled test to define the interactions and their effect on the control authority provided by the ACM. Techniques for measuring dynamic stability and for simulating rocket plume aerodynamics and acoustics were improved or developed in the course of building the aerodynamic and loads databases for Orion.

Activity Monitors as Support for Older Persons' Physical Activity in Daily Life: Qualitative Study of the Users' Experiences.

PubMed

Ehn, Maria; Eriksson, Lennie Carlén; Åkerberg, Nina; Johansson, Ann-Christin

2018-02-01

Falls are a major threat to the health and independence of seniors. Regular physical activity (PA) can prevent 40% of all fall injuries. The challenge is to motivate and support seniors to be physically active. Persuasive systems can constitute valuable support for persons aiming at establishing and maintaining healthy habits. However, these systems need to support effective behavior change techniques (BCTs) for increasing older adults' PA and meet the senior users' requirements and preferences. Therefore, involving users as codesigners of new systems can be fruitful. Prestudies of the user's experience with similar solutions can facilitate future user-centered design of novel persuasive systems. The aim of this study was to investigate how seniors experience using activity monitors (AMs) as support for PA in daily life. The addressed research questions are as follows: (1) What are the overall experiences of senior persons, of different age and balance function, in using wearable AMs in daily life?; (2) Which aspects did the users perceive relevant to make the measurements as meaningful and useful in the long-term perspective?; and (3) What needs and requirements did the users perceive as more relevant for the activity monitors to be useful in a long-term perspective? This qualitative interview study included 8 community-dwelling older adults (median age: 83 years). The participants' experiences in using two commercial AMs together with tablet-based apps for 9 days were investigated. Activity diaries during the usage and interviews after the usage were exploited to gather user experience. Comments in diaries were summarized, and interviews were analyzed by inductive content analysis. The users (n=8) perceived that, by using the AMs, their awareness of own PA had increased. However, the AMs' impact on the users' motivation for PA and activity behavior varied between participants. The diaries showed that self-estimated physical effort varied between participants and varied for each individual over time. Additionally, participants reported different types of accomplished activities; talking walks was most frequently reported. To be meaningful, measurements need to provide the user with a reliable receipt of whether his or her current activity behavior is sufficient for reaching an activity goal. Moreover, praise when reaching a goal was described as motivating feedback. To be useful, the devices must be easy to handle. In this study, the users perceived wearables as easy to handle, whereas tablets were perceived difficult to maneuver. Users reported in the diaries that the devices had been functional 78% (58/74) of the total test days. Activity monitors can be valuable for supporting seniors' PA. However, the potential of the solutions for a broader group of seniors can significantly be increased. Areas of improvement include reliability, usability, and content supporting effective BCTs with respect to increasing older adults' PA. ©Maria Ehn, Lennie Carlén Eriksson, Nina Åkerberg, Ann-Christin Johansson. Originally published in JMIR Mhealth and Uhealth (http://mhealth.jmir.org), 01.02.2018.

Integrated corridor management analysis, modeling, and simulation results for the test corridor.

DOT National Transportation Integrated Search

2008-06-01

This report documents the Integrated Corridor Management (ICM) Analysis Modeling and Simulation (AMS) tools and strategies used on a Test Corridor, presents results and lessons-learned, and documents the relative capability of AMS to support benefit-...

Microbial identification system for Space Station Freedom

NASA Technical Reports Server (NTRS)

Brown, Harlan D.; Scarlett, Janie B.; Skweres, Joyce A.; Fortune, Russell L.; Staples, John L.; Pierson, Duane L.

1989-01-01

The Environmental Health System (EHS) and Health Maintenance Facility (HMF) on Space Station Freedom will require a comprehensive microbiology capability. This requirement entails the development of an automated system to perform microbial identifications on isolates from a variety of environmental and clinical sources and, when required, to perform antimicrobial sensitivity testing. The unit currently undergoing development and testing is the Automated Microbiology System II (AMS II) built by Vitek Systems, Inc. The AMS II has successfully completed 12 months of laboratory testing and evaluation for compatibility with microgravity operation. The AMS II is a promising technology for use on Space Station Freedom.

Advanced Cosmic Ray Composition Experiment for Space Station (ACCESS)

NASA Technical Reports Server (NTRS)

Wilson, Thomas L.; Wefel, John P.

1999-01-01

In 1994 the first high-energy particle physics experiment for the Space Station, the Alpha Magnetic Spectrometer (AMS), was selected by NASA's Administrator as a joint collaboration with the U.S. Department of Energy (DOE). The AMS program was chartered to place a magnetic spectrometer in Earth orbit and search for cosmic antimatter. A natural consequence of this decision was that NASA would begin to explore cost-effective ways through which the design and implementation of AMS might benefit other promising payload experiments which were evolving from the Office of Space Science. The first such experiment to come forward was ACCESS in 1996. It was proposed as a new mission concept in space physics to place a cosmic-ray experiment of weight, volume, and geometry similar to the AMS on the ISS, and replace the latter as its successor when the AMS is returned to Earth. This was to be an extension of NASA's sub-orbital balloon program, with balloon payloads serving as the precursor flights and heritage for ACCESS. The balloon programs have always been a cost-effective NASA resource since the particle physics instrumentation for balloon and space applications are directly related. The next step was to expand the process, pooling together expertise from various NASA centers and universities while opening up definition of the ACCESS science goals to the international community through the standard practice of peer-review. This process is still on-going and the Accommodation Study presented here will discuss the baseline definition of ACCESS as we understand it today. Further detail on the history, scope, and background of the study is provided in Appendix A.

Phytoplankton growth response to Asian dust addition in the northwest Pacific Ocean versus the Yellow Sea

NASA Astrophysics Data System (ADS)

Zhang, Chao; Gao, Huiwang; Yao, Xiaohong; Shi, Zongbo; Shi, Jinhui; Yu, Yang; Meng, Ling; Guo, Xinyu

2018-02-01

In this study, five on-board microcosm experiments were performed in the subtropical gyre, the Kuroshio Extension region of the northwest Pacific Ocean (NWPO), and the Yellow Sea (YS) in order to investigate phytoplankton growth following the addition of artificially modified mineral dust (AM dust) and various nutrients (nitrogen (N), phosphorus (P), iron (Fe), N + P, and N + P + Fe). The two experiments carried out with AM-dust addition in the subtropical gyre showed a maximum chlorophyll a (Chl a) concentration increase of 1.7- and 2.8-fold, while the cell abundance of large-sized phytoplankton ( > 5 µm) showed a 1.8- and 3.9-fold increase, respectively, relative to the controls. However, in the Kuroshio Extension region and the YS, the increases in maximum Chl a and cell abundance of large-sized phytoplankton following AM-dust addition were at most 1.3-fold and 1.7-fold larger than those in the controls, respectively. A net conversion efficiency index (NCEI) newly proposed in this study, size-fractionated Chl a, and the abundance of large-sized phytoplankton were analysed to determine which nutrients contribute to supporting phytoplankton growth. Our results demonstrate that a combination of nutrients, N-P or N + P + Fe, is responsible for phytoplankton growth in the subtropical gyre following AM-dust addition. Single nutrient addition, i.e., N in the Kuroshio Extension region and P or N in the YS, controls the phytoplankton growth following AM-dust addition. In the AM-dust-addition experiments, in which the increased N-P or P was identified to determine phytoplankton growth, the dissolved inorganic P from AM dust (8.6 nmol L-1) was much lower than the theoretically estimated minimum P demand (˜ 20 nmol L-1) for phytoplankton growth. These observations suggest that additional supply augments the bioavailable P stock in incubated seawater with AM-dust addition, most likely due to an enhanced solubility of P from AM dust or the remineralization of the dissolved organic P.

Prevalence of acute mountain sickness on Mount Fuji: A pilot study.

PubMed

Horiuchi, Masahiro; Endo, Junko; Akatsuka, Shin; Uno, Tadashi; Jones, Thomas E

2016-04-01

Few studies have investigated climbing-related acute mountain sickness (AMS) on Mt Fuji. Although several studies of AMS have been conducted elsewhere, Mt Fuji is unique because there are many mountain lodges between the fifth station (a common starting point for climbers at an altitude of 2305 m) and the summit (3776 m), and many climbers commonly sleep overnight at mountain lodges during their ascents. This study surveyed the prevalence of AMS among climbers on Mt Fuji to determine which factors, if any, were related to the risk of developing AMS. This study collected data from 345 participants who climbed Mt Fuji in August 2013, including information regarding age, sex, climbing experience and whether the climber stayed at a mountain lodge (n = 239). AMS was surveyed using the Lake Louise Score (LLS) questionnaire. The item on perceived sleep quality was excluded for those who did not stay at a mountain lodge (n = 106). The overall prevalence of AMS was 29.5% (≥ 3 LLS with headache). According to a univariate analysis, AMS was not associated with sex (male vs female), age group (20-29, 30-39, 40-49 or >50 years) or stay at a mountain lodge (single day vs overnight stay). Conversely, prior experience climbing Mt Fuji (no prior attempts vs one or more prior attempts) was related to the risk of AMS. In addition, there was a significant deviation in the number of participants reporting poor sleep, and total sleep time was significantly shorter in participants with AMS. These preliminary findings suggest that no single factor can explain the risk for developing AMS while climbing Mt Fuji. In addition, impaired perceived sleep quality was associated with the severity of AMS in climbers who stayed overnight at a mountain lodge. © International Society of Travel Medicine, 2016. All rights reserved. Published by Oxford University Press. For permissions, please e-mail: journals.permissions@oup.com.

Booster Test for Space Launch System Rocket

NASA Image and Video Library

2016-06-26

The quench system arm and nozzle are seen at the test area where the second and final qualification motor (QM-2) test for the Space Launch System’s booster will take place, Sunday, June 26, 2016, at Orbital ATK Propulsion Systems test facilities in Promontory, Utah. The test is scheduled for Tuesday, June 28 at 10:05 a.m. EDT (8:05 a.m. MDT). Photo Credit: (NASA/Bill Ingalls)

Advanced Cosmic-Ray Composition Experiment for Space Station (ACCESS): ACCESS Accommodation Study Report

NASA Technical Reports Server (NTRS)

Wilson, Thomas L. (Editor); Wefel, John P. (Editor)

1999-01-01

In 1994 NASA Administrator selected the first high-energy particle physics experiment for the Space Station, the Alpha Magnetic Spectrometer (AMS), to place a magnetic spectrometer in Earth orbit and search for cosmic antimatter. A natural consequence of this decision was that NASA would begin to explore cost-effective ways through which the design and implementation of AMS might benefit other promising payload experiments. The first such experiment to come forward was Advanced Cosmic-Ray Composition Experiment for Space Station (ACCESS) in 1996. It was proposed as a new mission concept in space physics to attach a cosmic-ray experiment of weight, volume, and geometry similar to the AMS on the International Space Station (ISS), and replace the latter as its successor when the AMS is returned to Earth. This was to be an extension of NASA's suborbital balloon program, with balloon payloads serving as the precursor flights and heritage for ACCESS. The balloon programs have always been a cost-effective NASA resource since the particle physics instrumentation for balloon and space applications are directly related. The next step was to expand the process, pooling together expertise from various NASA centers and universities while opening up definition of the ACCESS science goals to the international community through the standard practice of peer review. This process is still ongoing, and the accommodation study presented here will discuss the baseline definition of ACCESS as we understand it today.

2011 Joint Missions Conference Held in Bloomington, Indiana on August 29-31, 2011

DTIC Science & Technology

2011-08-31

Breakfast Sponsored by CTC Foyer 8:00 AM – 8:15 AM NSWC Crane Welcome Remarks Great Hall  Mr. Duane Embree (SES), Technical...Director, NSWC Crane 8:15 AM – 8:30 AM NDIA Welcome Remarks Great Hall  MG Barry D. Bates, USA (Ret), VP Operations, NDIA 8:30 AM...Agile Response • Test and Evaluation Design • Concurrent systems evolution NPS Perspective on FX Research Dimensions HADR FX COCOM FX (Proposed)SOF FX

Genotypic variation in the response of chickpea to arbuscular mycorrhizal fungi and non-mycorrhizal fungal endophytes.

PubMed

Bazghaleh, Navid; Hamel, Chantal; Gan, Yantai; Tar'an, Bunyamin; Knight, Joan Diane

2018-04-01

Plant roots host symbiotic arbuscular mycorrhizal (AM) fungi and other fungal endophytes that can impact plant growth and health. The impact of microbial interactions in roots may depend on the genetic properties of the host plant and its interactions with root-associated fungi. We conducted a controlled condition experiment to investigate the effect of several chickpea (Cicer arietinum L.) genotypes on the efficiency of the symbiosis with AM fungi and non-AM fungal endophytes. Whereas the AM symbiosis increased the biomass of most of the chickpea cultivars, inoculation with non-AM fungal endophytes had a neutral effect. The chickpea cultivars responded differently to co-inoculation with AM fungi and non-AM fungal endophytes. Co-inoculation had additive effects on the biomass of some cultivars (CDC Corrine, CDC Anna, and CDC Cory), but non-AM fungal endophytes reduced the positive effect of AM fungi on Amit and CDC Vanguard. This study demonstrated that the response of plant genotypes to an AM symbiosis can be modified by the simultaneous colonization of the roots by non-AM fungal endophytes. Intraspecific variations in the response of chickpea to AM fungi and non-AM fungal endophytes indicate that the selection of suitable genotypes may improve the ability of crop plants to take advantage of soil ecosystem services.

Latest AMS Results on Cosmic Ray fluxes

NASA Astrophysics Data System (ADS)

Bertucci, Bruna; AMS Collaboration

2017-01-01

AMS-02 is a wide acceptance high-energy physics experiment installed on the International Space Station in May 2011 and it has been operating continuously since then. Accurate studies of CR composition and energy spectra can be performed in AMS thanks to the unprecedented collected statistics - more than 90 billion events as of today - and the redundant measurements of particle charge, velocity, rigidity and energy. In this contribution we will present an overview of the latest results on anti-particles, electrons and light nuclei fluxes. On behalf of the AMS Collaboration.

The AMS tracking detector for cosmic-ray physics in space

NASA Astrophysics Data System (ADS)

Bourquin, Maurice; AMS Tracker Collaboration

2005-04-01

AMS-02 is a general-purpose spectrometer designed to measure cosmic rays and gamma rays in near-Earth orbit. The main scientific motivations are the search for cosmic anti-matter, the search for dark matter, precision measurements on the relative abundance of different nuclei and isotopes, as well as the measurement of very high-energy gamma rays. Constructed by a large international collaboration of institutes from America, Asia and Europe, it will collect data on the International Space Station for a period of at least three years. In this contribution, I first identify the various detector requirements necessary to carry out this ambitious program. In particular, a large-area silicon microstrip detector inside a 0.8 T superconducting magnet is well suited to measure rigidity p/Z and specific energy loss d E/d x of cosmic rays, as well as the direction and energy of converted gamma rays. I review the advantage of such a silicon-tracking detector, taking into account the constraints of the space environment. The collaboration has gained extensive operating experience with double-sided silicon sensors in beam tests, and above all with AMS-01, a precursor spectrometer flown in the cargo bay of the Shuttle Discovery. During the entire 10-day STS-91 mission, the Silicon Tracker functioned without fault and with good spatial resolution. From the lessons learned with AMS-01, improvements were made to the design and assembly procedure of the 2500 sensors of AMS-02. As a result, the charge identification has been extended from Oxygen ( Z=8) to Iron ( Z=26). The physics reach of the new spectrometer is presented.

Biotic and Abiotic Stimulation of Root Epidermal Cells Reveals Common and Specific Responses to Arbuscular Mycorrhizal Fungi1[W

PubMed Central

Genre, Andrea; Ortu, Giuseppe; Bertoldo, Chiara; Martino, Elena; Bonfante, Paola

2009-01-01

During arbuscular mycorrhizal (AM) colonization, a focal accumulation of organelles occurs in root epidermal cells, prior to fungal penetration, beneath adhering hyphopodia. This is followed by the appearance of the prepenetration apparatus (PPA), a transcellular column of cytoplasm connected to the nucleus and rich in cytoskeleton and secretory endomembranes. This apparatus appears to be responsible for the construction of an apoplastic compartment that confines the fungus within the cell lumen. To identify AM-specific elements within the PPA response, we challenged root cultures of Medicago truncatula, expressing a green fluorescent protein tag for the endoplasmic reticulum, with an AM symbiont, a necrotrophic pathogen, a hemibiotrophic pathogen, a noncompatible endomycorrhizal fungus, or abiotic physical stimuli. Parallel experiments were made on a M. truncatula nonsymbiotic mutant (doesn't make infections, dmi3-1). The results have highlighted a correlation between physical stimulation of the cell surface and nuclear repositioning. Cytoplasmic aggregation was only induced by contact with compatible fungi, whereas PPA appearance was specifically triggered by the AM fungus. The dmi3-1 mutant did not develop cytoplasmic aggregation or PPA and underwent cell death upon physical stimulation. The up-regulation of an expansin-like gene, already identified as an early marker of AM fungal contact, was triggered in wild-type roots by all the fungi tested. Such observations identify responses that are specific to mycorrhizal interactions and extend the role of the DMI3 protein, a calcium/calmodulin-dependent kinase, from symbiotic to pathogenic interactions. PMID:19151131

Comparative Shock Response of Additively Manufactured Versus Conventionally Wrought 304L Stainless Steel*

NASA Astrophysics Data System (ADS)

Wise, J. L.; Adams, D. P.; Nishida, E. E.; Song, B.; Maguire, M. C.; Carroll, J.; Reedlunn, B.; Bishop, J. E.

2015-06-01

Gas-gun experiments have probed the compression and release behavior of impact-loaded 304L stainless steel specimens machined from additively manufactured (AM) blocks as well as baseline ingot-derived bar stock. The AM technology allows direct fabrication of metal parts. For the present study, a velocity interferometer (VISAR) measured the time-resolved motion of samples subjected to one-dimensional (i.e., uniaxial strain) shock compression to peak stresses ranging from 0.2 to 7.5 GPa. The acquired wave-profile data have been analyzed to determine the comparative Hugoniot Elastic Limit (HEL), Hugoniot equation of state, spall strength, and high-pressure yield strength of the AM and conventional materials. Observed differences in shock loading and unloading characteristics for the two 304L source variants have been correlated to complementary Kolsky bar results for compressive and tensile testing at lower strain rates. The effects of composition, porosity, microstructure (e.g., grain size and morphology), residual stress, and sample axis orientation relative to the additive manufacturing deposition trajectory have been assessed to explain differences between the AM and baseline 304L dynamic mechanical properties. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under Contract DE-AC04-94AL85000.

STS-107 Payload Specialist Ilan Ramon during TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Payload Specialist Ilan Ramon, the first Israeli astronaut, participates in Terminal Countdown Demonstration Test activities, a standard part of Shuttle launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

Alchemical prediction of hydration free energies for SAMPL

PubMed Central

Mobley, David L.; Liu, Shaui; Cerutti, David S.; Swope, William C.; Rice, Julia E.

2013-01-01

Hydration free energy calculations have become important tests of force fields. Alchemical free energy calculations based on molecular dynamics simulations provide a rigorous way to calculate these free energies for a particular force field, given sufficient sampling. Here, we report results of alchemical hydration free energy calculations for the set of small molecules comprising the 2011 Statistical Assessment of Modeling of Proteins and Ligands (SAMPL) challenge. Our calculations are largely based on the Generalized Amber Force Field (GAFF) with several different charge models, and we achieved RMS errors in the 1.4-2.2 kcal/mol range depending on charge model, marginally higher than what we typically observed in previous studies1-5. The test set consists of ethane, biphenyl, and a dibenzyl dioxin, as well as a series of chlorinated derivatives of each. We found that, for this set, using high-quality partial charges from MP2/cc-PVTZ SCRF RESP fits provided marginally improved agreement with experiment over using AM1-BCC partial charges as we have more typically done, in keeping with our recent findings5. Switching to OPLS Lennard-Jones parameters with AM1-BCC charges also improves agreement with experiment. We also find a number of chemical trends within each molecular series which we can explain, but there are also some surprises, including some that are captured by the calculations and some that are not. PMID:22198475

Continuous infusion of amphotericin B: preliminary experience at Faculdade de Medicina da Fundação ABC.

PubMed

Uehara, Roberto Palermo; Sá, Victor Hugo Lara de; Koshimura, Erika Tae; Prudente, Fernanda Vilas Boas; Tucunduva, Luciana Tomanik Cardozo de Mello; Gonçalves, Marina Sahade; Samano, Eliana Sueco Tibana; del Giglio, Auro

2005-09-01

Intravenous amphotericin B deoxycholate (AmB-D) infusions, usually given over 4 hours, frequently induce nephrotoxicity and undesirable infusion-related side effects such as rigors and chills. There is evidence in the literature that the use of AmB-D in the form of continuous 24-hour infusion is less toxic than the usual four-hour infusion of this drug. Our objective was to evaluate the efficacy and safety of continuous infusion of AmB-D for the treatment of persistent fever in neutropenic patients with hematological malignancies after chemotherapy. Observational retrospective analysis of our experience with continuous infusion of AmB-D, at Faculdade de Medicina da Fundação ABC and Hospital Estadual Mário Covas in Santo André. From October 2003 to May 2004, 12 patients with hematological malignancies and chemotherapy-induced neutropenia received 13 cycles of continuous infusion of AmB-D. The median dose of AmB-D was 0.84 mg/kg/day (0.33 to 2.30 mg/kg/day). Concomitant use of nephrotoxic medications occurred in 92% of the cycles. Nephrotoxicity occurred in 30.76% of the cycles, hypokalemia in 16.67%, hepatotoxicity in 30% and adverse infusion-related events in 23%. All patients survived for at least seven days after starting continuous infusion of AmB-D, and clinical resolution occurred in 76% of the cycles. Continuous infusion of AmB-D can be used in our Institution as an alternative to the more toxic four-hour infusion of AmB-D and possibly also as an alternative to the more expensive liposomal formulations of the drug.

Comparison of myocardial ischemia during intense mental stress using flight simulation in airline pilots with coronary artery disease to that produced with conventional mental and treadmill exercise stress testing.

PubMed

Doorey, Andrew; Denenberg, Barry; Sagar, Vidya; Hanna, Tracy; Newman, Jack; Stone, Peter H

2011-09-01

Mental stress increases cardiovascular morbidity and mortality. Although laboratory mental stress often causes less myocardial ischemia than exercise stress (ES), it is unclear whether mental stress is intrinsically different or differences are due to less hemodynamic stress with mental stress. We sought to evaluate the hemodynamic and ischemic response to intense realistic mental stress created by modern flight simulators and compare this response to that of exercise treadmill testing and conventional laboratory mental stress (CMS) testing in pilots with coronary disease. Sixteen airline pilots with angiographically documented coronary disease and documented myocardial ischemia during ES were studied using maximal treadmill ES, CMS, and aviation mental stress (AMS) testing. AMS testing was done in a sophisticated simulator using multiple system failures as stressors. Treadmill ES testing resulted in the highest heart rate, but AMS caused a higher blood pressure response than CMS. Maximal rate-pressure product was not significantly different between ES and AMS (25,646 vs 23,347, p = 0.08), although these were higher than CMS (16,336, p <0.0001). Despite similar hemodynamic stress induced by ES and AMS, AMS resulted in significantly less ST-segment depression and nuclear ischemia than ES. Differences in induction of ischemia by mental stress compared to ES do not appear to be due to the creation of less hemodynamic stress. In conclusion, even with equivalent hemodynamic stress, intense realistic mental stress induced by flight simulators results in significantly less myocardial ischemia than ES as measured by ST-segment depression and nuclear ischemia. Copyright © 2011 Elsevier Inc. All rights reserved.

Elution kinetics, antimicrobial activity, and mechanical properties of 11 different antibiotic loaded acrylic bone cement.

PubMed

Gálvez-López, Ruben; Peña-Monje, Alejandro; Antelo-Lorenzo, Ramón; Guardia-Olmedo, Juan; Moliz, Juan; Hernández-Quero, José; Parra-Ruiz, Jorge

2014-01-01

Antibiotic-loaded acrylic bone cements (ALABC) spacers are routinely used in the treatment of prosthetic joint infections. The objectives of our study were to evaluate different ALABC for elution kinetics, thermal stability, and mechanical properties. A 10 or 20% mixture (w/w) beads of medium viscosity bone cement (DePuy, Inc) and vancomycin (VAN), gentamycin (GM), daptomycin (DAP), moxifloxacin (MOX), rifampicin (RIF), cefotaxime (CTX), cefepime (FEP), amoxicillin clavulanate (AmC), ampicillin (AMP), meropenem (MER), and ertapenem (ERT) were formed and placed into wells filled with phosphate-buffered saline. Antibiotic concentrations were determined using high-performance liquid chromatography. Antimicrobial activity was tested against Micrococcus luteus ATCC 9341 or Escherichia coli ATCC 25922. AmC, AMP, and FEP concentration rapidly decreased after day 2, being almost undetectable at day 4. Sustained and high elution rates were observed with VAN, GM, MOX, and RIF for the 30-day duration of the experiment. DAP, MER, ERT, and CTX elution rates constantly decreased from day 4. All antibiotics tested retained antimicrobial activity proving thermal stability. Mechanical properties of ALABC were maintained except when RIF was used. © 2013.

The Neurophysiology of Autonomic Dysfunction in SCI: Plasticity in the Input and Output Neurons

DTIC Science & Technology

2014-04-01

multi-segmental spinal pain reflex Location: Halls B-H Presentation Time: Tuesday , Nov 16, 2010, 8:00 AM - 9:00 AM Authors: *K. E. TANSEY1, M...neurological scoring methods. Cognitive functions were tested using Fear Conditioning tests at 8–10 days post- injury and Morris Water Maze tests 11–15

AmO 2 Analysis for Analytical Method Testing and Assessment: Analysis Support for AmO 2 Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuhn, Kevin John; Bland, Galey Jean; Fulwyler, James Brent

Americium oxide samples will be measured for various analytes to support AmO 2 production. The key analytes that are currently requested by the Am production customer at LANL include total Am content, Am isotopics, Pu assay, Pu isotopics, and trace element content including 237Np content. Multiple analytical methods will be utilized depending on the sensitivity, accuracy and precision needs of the Am matrix. Traceability to the National Institute of Standards and Technology (NIST) will be achieved, where applicable, by running NIST traceable quality control materials. This given that there are no suitable AmO 2 reference materials currently available for requestedmore » analytes. The primary objective is to demonstrate the suitability of actinide analytical chemistry methods to support AmO 2 production operations.« less

Preliminary measurements of 135Cs with AMS

NASA Astrophysics Data System (ADS)

Yin, Xinyi; He, Ming; Dong, Kejun; Dou, Liang; Lan, Xiaoxi; Pang, Fangfang; Wu, Shaoyong; Jiang, Shan

2015-10-01

135Cs is an interesting nuclide in many research fields, especially in environmental study. Preliminary measurements of the long-lived 135Cs with accelerator mass spectrometry (AMS) have been developed with the HI-13 tandem AMS facility at China Institute of Atomic Energy (CIAE). In order to improve ion extracting current and depressing background interference, experiments were carried out on different ions of Cs extracted from different samples. It was found that Cs- extracted from CsNO3 can be used for AMS measurement of 135Cs. According to the preliminary results, the background level can be obtained with blanks was 135Ba/Cs ∼ 8.8 × 10-12 with the CIAE-AMS system.

DOE Non-Proliferation Experiment includes seismic data

NASA Astrophysics Data System (ADS)

Zucca, Jay

The U.S. Department of Energy detonated approximately 1.29 million kg of a commercial blasting agent, based on ammonium nitrate and fuel oil (ANFO), at the Nevada Test Site (NTS) on September 22, 1993, at 00:01.080 a.m. Pacific Daylight Time. The blasting agent was emplaced in a cylindrical chamber, approximately 15.2 m in diameter × 5.5 m high, located at 37.20193°N and 116.20986°E in a Rainier Mesa tunnel, 390 m underground. Code-named the Non-Proliferation Experiment (NPE), the explosion had an energy release of approximately 1 kt (1 kiloton = 4.186×1012 joules).

Starch-based Antimicrobial Films Incorporated with Lauric Acid and Chitosan

NASA Astrophysics Data System (ADS)

Salleh, E.; Muhamad, I. I.

2010-03-01

Antimicrobial (AM) packaging is one of the most promising active packaging systems. Starch-based film is considered an economical material for antimicrobial packaging. This study aimed at the development of food packaging based on wheat starch incorporated with lauric acid and chitosan as antimicrobial agents. The purpose is to restrain or inhibit the growth of spoilage and/or pathogenic microorganisms that are contaminating foods. The antimicrobial effect was tested on B. substilis and E. coli. Inhibition of bacterial growth was examined using two methods, i.e. zone of inhibition test on solid media and liquid culture test (optical density measurements). The control and AM films (incorporated with chitosan and lauric acid) were produced by casting method. From the observations, AM films exhibited inhibitory zones. Interestingly, a wide clear zone on solid media was observed for B. substilis growth inhibition whereas inhibition for E. coli was not as effective as B. substilis. From the liquid culture test, the AM films clearly demonstrated a better inhibition against B. substilis than E. coli.

Adaptation in sound localization processing induced by interaural time difference in amplitude envelope at high frequencies.

PubMed

Kawashima, Takayuki; Sato, Takao

2012-01-01

When a second sound follows a long first sound, its location appears to be perceived away from the first one (the localization/lateralization aftereffect). This aftereffect has often been considered to reflect an efficient neural coding of sound locations in the auditory system. To understand determinants of the localization aftereffect, the current study examined whether it is induced by an interaural temporal difference (ITD) in the amplitude envelope of high frequency transposed tones (over 2 kHz), which is known to function as a sound localization cue. In Experiment 1, participants were required to adjust the position of a pointer to the perceived location of test stimuli before and after adaptation. Test and adapter stimuli were amplitude modulated (AM) sounds presented at high frequencies and their positional differences were manipulated solely by the envelope ITD. Results showed that the adapter's ITD systematically affected the perceived position of test sounds to the directions expected from the localization/lateralization aftereffect when the adapter was presented at ±600 µs ITD; a corresponding significant effect was not observed for a 0 µs ITD adapter. In Experiment 2, the observed adapter effect was confirmed using a forced-choice task. It was also found that adaptation to the AM sounds at high frequencies did not significantly change the perceived position of pure-tone test stimuli in the low frequency region (128 and 256 Hz). The findings in the current study indicate that ITD in the envelope at high frequencies induces the localization aftereffect. This suggests that ITD in the high frequency region is involved in adaptive plasticity of auditory localization processing.

A&M. A&M building (TAN607). Camera facing east. From left to ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. A&M building (TAN-607). Camera facing east. From left to right, pool section, hot shop, cold shop, and machine shop. Biparting doors to hot shop are in open position behind shroud. Four rail tracks lead to hot shop and cold shop. Date: August 20, 1954. INEEL negative no. 11706 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

AM(VI) partitioning studies. FY14 final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mincher, Bruce J.

2014-10-01

The use of higher oxidation states of americium in partitioning from the lanthanides is under continued investigation by the sigma team. This is based on the hypothesis that Am(VI) can be produced and remain stable in irradiated first cycle raffinate solution long enough to perform solvent extraction for separations. The stability of Am(VI) to autoreduction was measured using millimolar americium concentrations in a 1-cm cell with a Cary 6000 UV/Vis spectrophotometer for data acquisition. At millimolar americium concentrations, Am(VI) is stable enough against its own autoreduction for separations purposes. A second major accomplishment during FY14 was the hot test. Americiummore » oxidation and extraction was performed using a centrifugal contactor-based test bed consisting of an extraction stage and two stripping stages. Sixty-three percent americium extraction was obtained in one extraction stage, in agreement with batch contacts. Promising electrochemical oxidation results have also been obtained, using terpyridine ligand derivatized electrodes for binding of Am(III). Approximately 50 % of the Am(III) was oxidized to Am(V) over the course of 1 hour. It is believed that this is the first demonstration of the electrolytic oxidation of americium in a non-complexing solution. Finally, an initial investigation of Am(VI) extraction using diethylhexylbutyramide (DEHBA) was performed.« less

Data related to the experimental design for powder bed binder jetting additive manufacturing of silicone.

PubMed

Liravi, Farzad; Vlasea, Mihaela

2018-06-01

The data included in this article provides additional supporting information on our recent publication (Liravi et al., 2018 [1]) on a novel hybrid additive manufacturing (AM) method for fabrication of three-dimensional (3D) structures from silicone powder. A design of experiments (DoE) study has been carried out to optimize the geometrical fidelity of AM-made parts. This manuscript includes the details of a multi-level factorial DOE and the response optimization results. The variation in the temperature of powder-bed when exposed to heat is plotted as well. Furthermore, the effect of blending ratio of two parts of silicone binder on its curing speed was investigated by conducting DSC tests on a silicone binder with 100:2 precursor to curing agent ratio. The hardness of parts fabricated with non-optimum printing conditions are included and compared.

Basic EMC (Electromagnetic compatibility) technology advancement for C3 (Command, control, and communications) systems. Volume 6

NASA Astrophysics Data System (ADS)

Weiner, D.; Paul, C. R.; Whalen, J.

1985-04-01

This research effort was devoted to eliminating some of the basic technological gaps in the two important areas of: (1) electromagnetic effects (EM) on microelectronic circuits and (2) EM coupling and testing. The results are presented in fourteen reports which have been organized into six volumes. The reports are briefly summarized in this volume. In addition, an experiment is described which was performed to demonstrate the feasibility of applying several of the results to a problem involving electromagnetic interference. Specifically, experimental results are provided for the randomness associated with: (1) crosstalk in cable harnesses and (2) demodulation of amplitude modulated (AM) signals in operational amplifiers. These results are combined to predict candidate probability density functions (pdf's) for the amplitude of an AM interfering signal required to turn on a light emitting diode. The candidate pdf's are shown to be statistically consistent with measured data.

Two Novel Algicidal Isolates Kill Chlorella pyrenoidosa by Inhibiting their Host Antioxidase Activities.

PubMed

Liao, Chunli; Liu, Xiaobo; Liu, Ruifang; Shan, Linna

2015-09-01

In the biocontrol of harmful algal blooms, there has been considerable interest about the role of algicidal bacteria in algicidal activity. In this experiment, two novel algicidal bacteria (strains NP23 and AM11) against Chlorella pyrenoidosa were isolated from the Baiguishan reservoir in China. Phylogenetic analysis based on 16S rRNA gene sequences revealed that strains NP23 and AM11 belonged to Enterobacter cloacae and Gibberella moniliformis, respectively. To further understand the algicidal activities, five parameters including the chlorophyll a content, cell survival rate, superoxide dismutase (SOD) peroxide dismutase (POD), and catalase (CAT) were tested in the C. pyrenoidosa cells after inoculation with the algicidal bacteria Enterobacter cloacae NP23 and Gibberella moniliformis AM11. As a result, the growth of the treated C. pyrenoidosa was significantly restrained with a great decline of chlorophyll a content. Meanwhile, three antioxidase activities of the treated C. pyrenoidosa were initially stimulated from day 1 to day 3 but then dramatically inhibited at low level. These results induced that the oxidative imbalance (i.e., inhibition of antioxidase activities) caused by algicidal bacteria could be the killing agent of the C. pyrenoidosa cells.

Specific interactions between arbuscular mycorrhizal fungi and plant growth-promoting bacteria--as revealed by different combinations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jaderlund, Lotta; Arthurson, Veronica; Granhall, Ulf

2008-05-15

The interactions between two plant growth promoting rhizobacteria (PGPR), Pseudomonas fluorescens SBW25 and Paenibacillus brasilensis PB177, two arbuscular mycorrhizal (AM) fungi (Glomus mosseae and G. intraradices) and one pathogenic fungus (Microdochium nivale) were investigated on winter wheat (Triticum aestivum cultivar Tarso) in a greenhouse trial. PB177, but not SBW25, had strong inhibitory effects on M. nivale in dual culture plate assays. The results from the greenhouse experiment show very specific interactions; e.g. the two AM fungi react differently when interacting with the same bacteria on plants. G. intraradices (single inoculation or together with SBW25) increased plant dry weight on M.more » nivale infested plants, suggesting that the pathogenic fungus is counteracted by G. intraradices, but PB177 inhibited this positive effect. This is an example of two completely different reactions between the same AM fungus and two species of bacteria, previously known to enhance plant growth and inhibit pathogens. When searching for plant growth promoting microorganisms it is therefore important to test for the most suitable combination of plant, bacteria and fungi in order to get satisfactory plant growth benefits.« less

How interacting fungal species and mineral nitrogen inputs affect transfer of nitrogen from litter via arbuscular mycorrhizal mycelium.

PubMed

He, Yuejun; Cornelissen, J Hans C; Zhong, Zhangcheng; Dong, Ming; Jiang, Changhong

2017-04-01

In the karst landscape, widespread in the world including southern China, soil nutrient supply is strongly constrained. In such environments, arbuscular mycorrhizal (AM) fungi may facilitate plant nutrient uptake. However, the possible role of different AM fungal species, and their interactions, especially in transferring nitrogen (N) from litter to plant, is poorly understood. We conducted two microcosm experiments to investigate the role that two karst soil AM fungi, Glomus etunicatum and Glomus mosseae, play in the transfer of N from decomposing litter to the host plant and to determine how N availability influences these processes. In experiment 1, Cinnamomum camphora tree seedlings were grown in compartments inoculated with G. etunicatum. Lolium perenne leaf litter labeled with δ 15 N was added to the soil in unplanted compartments. Compartments containing the δ 15 N labeled litter were either accessible to hyphae but not to seedling roots or were not accessible to hyphae or roots. The addition of mineral N to one of the host compartments at the start of the experiment significantly increased the biomass of the C. camphora seedlings, N content and N:P ratio, AM mycelium length, and soil microbial biomass carbon and N. However, significantly, more δ 15 N was acquired, from the leaf litter by the AM hyphae and transferred to the host when mineral N was not added to the soil. In experiment 2, in which C. camphora seedlings were inoculated with both G. etunicatum and G. mosseae rather than with G. mosseae alone, there was a significant increase in mycelial growth (50.21%), in soil microbial biomass carbon (417.73%) in the rhizosphere, and in the amount of δ 15 N that was transferred to the host. These findings suggest that maintaining AM fungal diversity in karst soils could be important for mediating N transfer from organic material to host plants in N-poor soils.

AM2 Mat End Connector Modeling and Performance Validation

DTIC Science & Technology

2015-08-01

9 3.2.1 Subgrade construction and posttest forensics...layout. 3.2.1 Subgrade construction and posttest forensics The test section subgrade was built using in-place material from a previous AM2 test...area 50 ft wide by 42 ft long of the existing test bed was removed and replaced with newly processed material. Posttest values from the previous

STS-107 Payload Specialist Ilan Ramon suits up for TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Payload Specialist Ilan Ramon, the first Israeli astronaut, gets help with his suitup for Terminal Countdown Demonstration Test activities, which include a simulated launch countdown at the pad. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia. .

STS-107 Pilot William McCool in the cockpit of Columbia during TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. - STS-107 Pilot William 'Willie' McCool checks instructions in the cockpit of Space Shuttle Columbia during a simulated launch countdown, part of Terminal Countdown Demonstration Test activities. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia. .

STS-107 Mission Specialist David Brown suits up for TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Mission Specialist David Brown happily submits to suit check prior to Terminal Countdown Demonstration Test activities, which include a simulated launch countdown at the pad. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia. .

STS-107 Mission Specialist Laurel Clark suits up for TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. - STS-107 Mission Specialist Laurel Clark happily submits to suit check prior to Terminal Countdown Demonstration Test activities, which include a simulated launch countdown at the pad. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia. .

STS-107 Payload Specialist Ilan Ramon suits up for TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. - STS-107 Payload Specialist Ilan Ramon, the first Israeli astronaut, sits happily during suitup for Terminal Countdown Demonstration Test activities, which include a simulated launch countdown at the pad. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia. .

STS-107 Mission Specialist David Brown suits up for TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Mission Specialist David Brown waves as he completes suit check prior to Terminal Countdown Demonstration Test activities, which include a simulated launch countdown at the pad. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia. .

STS-107 Mission Specialist Kalpana Chawla during TCDT at LC-39A

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. - STS-107 Mission Specialist Kalpana Chawla is shown during the crew's Terminal Countdown Demonstration Test activities on Launch Pad 39A. The TCDT also includes a simulated launch countdown. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia. .

STS-107 Mission Specialist Laurel Clark suits up for TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Mission Specialist Laurel Clark has her helmet checked during suitup for Terminal Countdown Demonstration Test activities, which include a simulated launch countdown at the pad. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia. .

KSC-02pd1937

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- -- STS-107 Pilot William "Willie" McCool operates an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. Instructor George Hoggard (left) supervises the training. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

KSC-02pd1930

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- STS-107 Mission Specialist Laurel Clark (in yellow cap) is instructed on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

KSC-02pd1935

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- -- STS-107 Mission Specialist David Brown takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

KSC-02pd1934

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- -- STS-107 Payload Commander Michael Anderson takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

KSC-02pd1928

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- STS-107 Mission Specialist Kalpana Chawla takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

KSC-02pd1931

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- STS-107 Payload Specialist Ilan Ramon, the first Israeli astronaut, takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

KSC-02pd1936

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- -- STS-107 Pilot William "Willie" McCool takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

Modified Light Duty AM2 Capability Assessment

DTIC Science & Technology

The Modified Light -Duty AM2 matting was designed specifically for lightweight, remote-piloted aircraft (RPA) applications. An in- depth study was... Ratio (CBR) of 6. To understand the full potential of the Modified Light -Duty AM2, a full- scale evaluation was performed with contingency C-17 and...stir welding for use in fabrication of the lightweight RPA matting in conjunction with a full- scale test on the Modified Light -Duty AM2 matting system

Toward a Common Language for Measuring Patient Mobility in the Hospital: Reliability and Construct Validity of Interprofessional Mobility Measures.

PubMed

Hoyer, Erik H; Young, Daniel L; Klein, Lisa M; Kreif, Julie; Shumock, Kara; Hiser, Stephanie; Friedman, Michael; Lavezza, Annette; Jette, Alan; Chan, Kitty S; Needham, Dale M

2018-02-01

The lack of common language among interprofessional inpatient clinical teams is an important barrier to achieving inpatient mobilization. In The Johns Hopkins Hospital, the Activity Measure for Post-Acute Care (AM-PAC) Inpatient Mobility Short Form (IMSF), also called "6-Clicks," and the Johns Hopkins Highest Level of Mobility (JH-HLM) are part of routine clinical practice. The measurement characteristics of these tools when used by both nurses and physical therapists for interprofessional communication or assessment are unknown. The purposes of this study were to evaluate the reliability and minimal detectable change of AM-PAC IMSF and JH-HLM when completed by nurses and physical therapists and to evaluate the construct validity of both measures when used by nurses. A prospective evaluation of a convenience sample was used. The test-retest reliability and the interrater reliability of AM-PAC IMSF and JH-HLM for inpatients in the neuroscience department (n = 118) of an academic medical center were evaluated. Each participant was independently scored twice by a team of 2 nurses and 1 physical therapist; a total of 4 physical therapists and 8 nurses participated in reliability testing. In a separate inpatient study protocol (n = 69), construct validity was evaluated via an assessment of convergent validity with other measures of function (grip strength, Katz Activities of Daily Living Scale, 2-minute walk test, 5-times sit-to-stand test) used by 5 nurses. The test-retest reliability values (intraclass correlation coefficients) for physical therapists and nurses were 0.91 and 0.97, respectively, for AM-PAC IMSF and 0.94 and 0.95, respectively, for JH-HLM. The interrater reliability values (intraclass correlation coefficients) between physical therapists and nurses were 0.96 for AM-PAC IMSF and 0.99 for JH-HLM. Construct validity (Spearman correlations) ranged from 0.25 between JH-HLM and right-hand grip strength to 0.80 between AM-PAC IMSF and the Katz Activities of Daily Living Scale. The results were obtained from inpatients in the neuroscience department of a single hospital. The AM-PAC IMSF and JH-HLM had excellent interrater reliability and test-retest reliability for both physical therapists and nurses. The evaluation of convergent validity suggested that AM-PAC IMSF and JH-HLM measured constructs of patient mobility and physical functioning. © 2017 American Physical Therapy Association

Insight into the Am-O Phase Equilibria: A Thermodynamic Study Coupling High-Temperature XRD and CALPHAD Modeling.

PubMed

Epifano, Enrica; Guéneau, Christine; Belin, Renaud C; Vauchy, Romain; Lebreton, Florent; Richaud, Jean-Christophe; Joly, Alexis; Valot, Christophe; Martin, Philippe M

2017-07-03

In the frame of minor actinide transmutation, americium can be diluted in UO 2 and (U, Pu)O 2 fuels burned in fast neutron reactors. The first mandatory step to foresee the influence of Am on the in-reactor behavior of transmutation targets or fuel is to have fundamental knowledge of the Am-O binary system and, in particular, of the AmO 2-x phase. In this study, we coupled HT-XRD (high-temperature X-ray diffraction) experiments with CALPHAD thermodynamic modeling to provide new insights into the structural properties and phase equilibria in the AmO 2-x -AmO 1.61+x -Am 2 O 3 domain. Because of this approach, we were able for the first time to assess the relationships between temperature, lattice parameter, and hypostoichiometry for fcc AmO 2-x . We showed the presence of a hyperstoichiometric existence domain for the bcc AmO 1.61+x phase and the absence of a miscibility gap in the fcc AmO 2-x phase, contrary to previous representations of the phase diagram. Finally, with the new experimental data, a new CALPHAD thermodynamic model of the Am-O system was developed, and an improved version of the phase diagram is presented.

Neural Correlates of Glucocorticoids Effects on Autobiographical Memory Retrieval in Healthy Women.

PubMed

Fleischer, Juliane; Metz, Sophie; Düsenberg, Moritz; Grimm, Simone; Golde, Sabrina; Roepke, Stefan; Renneberg, Babette; Wolf, Oliver T; Otte, Christian; Wingenfeld, Katja

2018-06-22

It is well known that elevated cortisol after stress or after exogenous administration impairs episodic memory retrieval including autobiographical memory (AM) retrieval. This impairment might be mediated by deactivation of a neural network associated with memory retrieval including the prefrontal cortex (PFC) and limbic structures. However, the neural underpinnings of these cortisol effects on AM retrieval have not been investigated yet. In this study, thirty-three healthy women received either placebo or 10 mg hydrocortisone in a double blind cross-over design before completing an AM test during fMRI. In this test, participants are asked to recall specific events from their own past in response to a cue word. In a first step, we analyzed the neural underpinnings of AM retrieval in the placebo condition. We found an activation pattern consistent with core regions involved in autobiographical memory recall, including the ventromedial PFC, anterior medial (am)PFC, inferior frontal gyrus, the posterior cingulate cortex, the tempoparietal junction, the middle temporal gyrus and the hippocampus. Further, we analyzed brain activation during AM retrieval after hydrocortisone compared to placebo. Region of interest (ROI) analyses revealed a hydrocortisone-induced deactivation during AM retrieval in the right amPFC. Results of the ROI analyses were non-significant in the left and right hippocampus, the left and right vmPFC and the left amPFC In sum, during AM retrieval hydrocortisone had the most pronounced effects on the amPFC. This might be explained by the strong involvement of this brain region in self-referential behavior, which is essential for recalling autobiographic information. Copyright © 2018. Published by Elsevier B.V.

Phylogenetically diverse AM fungi from Ecuador strongly improve seedling growth of native potential crop trees.

PubMed

Schüßler, Arthur; Krüger, Claudia; Urgiles, Narcisa

2016-04-01

In many deforested regions of the tropics, afforestation with native tree species could valorize a growing reservoir of degraded, previously overused and abandoned land. The inoculation of tropical tree seedlings with arbuscular mycorrhizal fungi (AM fungi) can improve tree growth and viability, but efficiency may depend on plant and AM fungal genotype. To study such effects, seven phylogenetically diverse AM fungi, native to Ecuador, from seven genera and a non-native AM fungus (Rhizophagus irregularis DAOM197198) were used to inoculate the tropical potential crop tree (PCT) species Handroanthus chrysanthus (synonym Tabebuia chrysantha), Cedrela montana, and Heliocarpus americanus. Twenty-four plant-fungus combinations were studied in five different fertilization and AMF inoculation treatments. Numerous plant growth parameters and mycorrhizal root colonization were assessed. The inoculation with any of the tested AM fungi improved seedling growth significantly and in most cases reduced plant mortality. Plants produced up to threefold higher biomass, when compared to the standard nursery practice. AM fungal inoculation alone or in combination with low fertilization both outperformed full fertilization in terms of plant growth promotion. Interestingly, root colonization levels for individual fungi strongly depended on the host tree species, but surprisingly the colonization strength did not correlate with plant growth promotion. The combination of AM fungal inoculation with a low dosage of slow release fertilizer improved PCT seedling performance strongest, but also AM fungal treatments without any fertilization were highly efficient. The AM fungi tested are promising candidates to improve management practices in tropical tree seedling production.

AMS,Chang-Diaz works with computers in the middeck

NASA Image and Video Library

2016-08-24

STS091-378-028 (2-12 June 1998) --- Astronaut Franklin R. Chang-Diaz, payload commander, inputs data on a laptop computer associated with the Alpha Magnetic Spectrometer (AMS) hardware located in the aft cargo bay. Reference JSC photo number STS091-367-033, which shows the hardware as seen from Russia's Mir space station, which was docked with Discovery at the time. AMS is the first large magnet experiment ever placed in Earth orbit. The scientific goal of this high-energy physics experiment is to increase our understanding of the composition and origin of the universe. It is designed to search for and measure charged particles, including antimatter, outside Earth's atmosphere. The charge of such particles can be identified by their trajectories in a magnetic field.

Atomic magnetometer-based ultra-sensitive magnetic microscopy

NASA Astrophysics Data System (ADS)

Kim, Young Jin; Savukov, Igor

2016-03-01

An atomic magnetometer (AM) based on lasers and alkali-metal vapor cells is currently the most sensitive non-cryogenic magnetic-field sensor. Many applications in neuroscience and other fields require high resolution, high sensitivity magnetic microscopic measurements. In order to meet this need we combined a cm-size spin-exchange relaxation-free AM with a flux guide (FG) to produce an ultra-sensitive FG-AM magnetic microscope. The FG serves to transmit the target magnetic flux to the AM thus enhancing both the sensitivity and resolution for tiny magnetic objects. In this talk, we will describe a prototype FG-AM device and present experimental and numerical tests of its sensitivity and resolution. We also demonstrate that an optimized FG-AM achieves high resolution and high sensitivity sufficient to detect a magnetic field of a single neuron in a few seconds, which would be an important milestone in neuroscience. We anticipate that this unique device can be applied to the detection of a single neuron, the detection of magnetic nano-particles, which in turn are very important for detection of target molecules in national security and medical diagnostics, and non-destructive testing.

Identification of key residues involved in adrenomedullin binding to the AM1 receptor

PubMed Central

Watkins, HA; Au, M; Bobby, R; Archbold, JK; Abdul-Manan, N; Moore, JM; Middleditch, MJ; Williams, GM; Brimble, MA; Dingley, AJ; Hay, DL

2013-01-01

Background and Purpose Adrenomedullin (AM) is a peptide hormone whose receptors are members of the class B GPCR family. They comprise a heteromer between the GPCR, the calcitonin receptor-like receptor and one of the receptor activity-modifying proteins 1–3. AM plays a significant role in angiogenesis and its antagonist fragment AM22–52 can inhibit blood vessel and tumour growth. The mechanism by which AM interacts with its receptors is unknown. Experimental Approach We determined the AM22–52 binding epitope for the AM1 receptor extracellular domain using biophysical techniques, heteronuclear magnetic resonance spectroscopy and alanine scanning. Key Results Chemical shift perturbation experiments located the main binding epitope for AM22–52 at the AM1 receptor to the C-terminal 8 amino acids. Isothermal titration calorimetry of AM22–52 alanine-substituted peptides indicated that Y52, G51 and I47 are essential for AM1 receptor binding and that K46 and P49 and R44 have a smaller role to play. Characterization of these peptides at the full-length AM receptors was assessed in Cos7 cells by cAMP assay. This confirmed the essential role of Y52, G51 and I47 in binding to the AM1 receptor, with their substitution resulting in ≥100-fold reduction in antagonist potency compared with AM22–52. R44A, K46A, S48A and P49A AM22–52 decreased antagonist potency by approximately 10-fold. Conclusions and Implications This study localizes the main binding epitope of AM22–52 to its C-terminal amino acids and distinguishes essential residues involved in this binding. This will inform the development of improved AM receptor antagonists. PMID:23351143

LEO Flight Testing of GaAs on Si Solar Cells Aboard MISSES

NASA Technical Reports Server (NTRS)

Wilt, David M.; Clark, Eric B.; Ringel, Steven A.; Andre, Carrie L.; Smith, Mark A.; Scheiman, David A.; Jenkins, Phillip P.; Maurer, William F.; Fitzgerald, Eugene A.; Walters, R. J.

2004-01-01

Previous research efforts have demonstrated small area (0.04 cm) GaAs on Si (GaAs/Si) solar cells with AM0 efficiencies in excess of 17%. These results were achieved on Si substrates coated with a step graded buffer of Si(x),Ge(1-x) alloys graded to 100% Ge. Recently, a 100-fold increase in device area was accomplished for these devices in preparation for on-orbit testing of this technology aboard Materials International Space Station Experiment number 5 (MISSE5). The GaAs/Si MISSE5 experiment contains five (5) GaAs/Si test devices with areas of lcm(exp 2) and 4cm(exp 4) as well as two (2) GaAs on GaAs control devices. Electrical performance data, measured on-orbit for three (3) of the test devices and one (1) of the control devices, will be telemetered to ground stations daily. After approximately one year on orbit, the MISSE5 payload will be returned to Earth for post flight evaluation. This paper will discuss the development of the GaAs/Si devices for the MISSE5 flight experiment and will present recent ground and on-orbit performance data.

Evaluation of detection and response times of fire sensors using an atmospheric monitoring system

PubMed Central

Rowland, J.H.; Litton, C.D.; Thomas, R.A.

2017-01-01

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners. PMID:28529442

Evaluation of detection and response times of fire sensors using an atmospheric monitoring system.

PubMed

Rowland, J H; Litton, C D; Thomas, R A

2016-01-01

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Dynamic behavior of acoustic metamaterials and metaconfigured structures with local oscillators

NASA Astrophysics Data System (ADS)

Manimala, James Mathew

Dynamic behavior of acoustic metamaterials (AM) and metaconfigured structures (MCS) with various oscillator-type microstructures or local attachments was investigated. AM derive their unusual elastic wave manipulation capabilities not just from material constituents but more so from engineered microstructural configurations. Depending on the scale of implementation, these "microstructures" may be deployed as microscopic inclusions in metacomposites or even as complex endo-structures within load-bearing exo-structures in MCS. The frequency-dependent negative effective-mass exhibited by locally resonant microstructures when considered as a single degree of freedom system was experimentally verified using a structure with an internal mass-spring resonator. AM constructed by incorporating resonators in a host material display spatial attenuation of harmonic stress waves within a tunable bandgap frequency range. An apparent damping coefficient was derived to compare the degree of attenuation achieved in these wholly elastic AM to equivalent conventionally damped models illustrating their feasibility as stiff structures that simultaneously act as effective damping elements. Parametric studies were performed using simulations to design and construct MCS with attached resonators for dynamic load mitigation applications. 98% payload isolation at resonance (7 Hz) was experimentally attained using a low-frequency vibration isolator with tip-loaded cantilever beam resonators. Pendulum impact tests on a resonator stack substantiated a peak transmitted stress reduction of about 60% and filtering of the resonator frequencies in the transmitted spectrum. Drop-tower tests were done to gauge the shock mitigation performance of an AM-inspired infrastructural building-block with internal resonators. Proof-of-concept experiments using an array of multifunctional resonators demonstrate the possibility of integrating energy harvesting and transducer capabilities. Stress wave attenuation in locally dissipative AM with various damped oscillator microstructures was studied using mechanical lattice models. The presence of damping was represented by a complex effective-mass. Analytical transmissibilities and numerical verifications were obtained for Kelvin-Voigt-type, Maxwell-type and Zener-type oscillators. Although peak attenuation at resonance is diminished, broadband attenuation was found to be achievable without increasing mass ratio, obviating the bandgap width limitations of locally resonant AM. Static and frequency-dependent measures of optimal damping that maximize the attenuation characteristics were established. A transitional value for the excitation frequency was identified within the locally resonant bandgap, above which there always exists an optimal amount of damping that renders the attenuation for the dissipative AM greater than that for the locally resonant case. AM with nonlinear stiffnesses were also investigated. For a base-excited two degree of freedom system consisting of a master structure and a Duffing-type oscillator, approximate transmissibility was derived, verified using simulations and compared to its equivalent damped model. Analytical solutions for dispersion curve shifts in nonlinear chains with linear resonators and in linear chains with nonlinear oscillators were obtained using perturbation analysis and first order approximations for cubic hardening and softening cases. Amplitude-activated alterations in bandgap width and the possibility of phenomena such as branch curling and overtaking were observed. Device implications of nonlinear AM as amplitude-dependent filters and direction-biased waveguides were examined using simulations.

Quantitative characterization of galectin-3-C affinity mass spectrometry measurements: Comprehensive data analysis, obstacles, shortcuts and robustness.

PubMed

Haramija, Marko; Peter-Katalinić, Jasna

2017-10-30

Affinity mass spectrometry (AMS) is an emerging tool in the field of the study of protein•carbohydrate complexes. However, experimental obstacles and data analysis are preventing faster integration of AMS methods into the glycoscience field. Here we show how analysis of direct electrospray ionization mass spectrometry (ESI-MS) AMS data can be simplified for screening purposes, even for complex AMS spectra. A direct ESI-MS assay was tested in this study and binding data for the galectin-3C•lactose complex were analyzed using a comprehensive and simplified data analysis approach. In the comprehensive data analysis approach, noise, all protein charge states, alkali ion adducts and signal overlap were taken into account. In a simplified approach, only the intensities of the fully protonated free protein and the protein•carbohydrate complex for the main protein charge state were taken into account. In our study, for high intensity signals, noise was negligible, sodiated protein and sodiated complex signals cancelled each other out when calculating the K d value, and signal overlap influenced the Kd value only to a minor extent. Influence of these parameters on low intensity signals was much higher. However, low intensity protein charge states should be avoided in quantitative AMS analyses due to poor ion statistics. The results indicate that noise, alkali ion adducts, signal overlap, as well as low intensity protein charge states, can be neglected for preliminary experiments, as well as in screening assays. One comprehensive data analysis performed as a control should be sufficient to validate this hypothesis for other binding systems as well. Copyright © 2017 John Wiley & Sons, Ltd.

Selective changes in locomotor activity in mice due to low-intensity microwaves amplitude modulated in the EEG spectral domain.

PubMed

Van Eeghem, Vincent; El Arfani, Anissa; Anthoula, Arta; Walrave, Laura; Pourkazemi, Ali; Bentea, Eduard; Demuyser, Thomas; Smolders, Ilse; Stiens, Johan

2017-09-17

Despite the numerous benefits of microwave applications in our daily life, microwaves were associated with diverse neurological complaints such as headaches and impaired sleep patterns, and changes in the electroencephalogram (EEG). To which extent microwaves influence the brain function remains unclear. This exploratory study assessed the behavior and neurochemistry in mice immediately or 4weeks after a 6-day exposure to low-intensity 10-GHz microwaves with an amplitude modulation (AM) of 2 or 8Hz. These modulation frequencies of 2 and 8Hz are situated within the delta and theta-alpha frequency bands in the EEG spectrum and are associated with sleep and active behavior, respectively. During these experiments, the specific absorbance rate was 0.3W/kg increasing the brain temperature with 0.23°C. For the first time, exposing mice to 8-Hz AM significantly reduced locomotor activity in an open field immediately after exposure which normalized after 4weeks. This in contrast to 2-Hz AM which didn't induce significant changes in locomotor activity immediately and 4weeks after exposure. Despite this difference in motor behavior, no significant changes in striatal dopamine (DA) and 3,4-dihydroxyphenylacetic acid (DOPAC) levels and DOPAC/DA turnover nor in cortical glutamate (GLU) concentrations were detected. In all cases, no effects on motor coordination on a rotarod, spatial working memory, anxiety nor depressive-like behavior were observed. The outcome of this study indicates that exposing mice to low-intensity 8-Hz AM microwaves can alter the locomotor activity in contrast to 2-Hz AM which did not affect the tested behaviors. Copyright © 2017 IBRO. Published by Elsevier Ltd. All rights reserved.

Mechanisms of Analgesic and Anti-Inflammatory Properties of Annona muricata Linn. (Annonaceae) Fruit Extract in Rodents

PubMed Central

Ishola, Ismail O.; Olusayero, Abayomi Micheal; Ochieng, Charles O.

2014-01-01

Abstract Unripe fruit of Annona muricata Linn. (Annonaceae) (soursop) is used in traditional African medicine for the treatment of neuralgia, rheumatism, and arthritic pain. This study sought to investigate the analgesic and anti-inflammatory effects of lyophilized fruit extract of Annona muricata (AM) in rodents. The analgesic activity was evaluated using the mouse writhing, formalin, and hot-plate tests while the anti-inflammatory action was investigated using the carrageenan-induced rat paw edema and xylene-induced ear edema tests. Pretreatment with AM (50, 100, and 200 mg/kg, p.o.) produced dose-dependent (P<.001) inhibition of writhes and formalin-induced pain in the late phase. AM and morphine produced time-course increase in pain threshold in hot-plate test. However, the analgesic effect elicited by AM was reversed (P<.05) by naloxone pretreatment. Similarly, the time-dependent increase in paw circumference induced by carrageenan was inhibited by AM treatment with peak effect (0.23±0.10 cm; P<.001, 200 mg/kg; 6 h), which was comparatively similar to that of diclofenac treated. Further, the xylene-induced ear edema was significantly reduced by AM (50 or 100 mg/kg) pretreatment; however, the anti-inflammatory effect elicited by AM was prevented by pretreatment of mice with NG-nitro-l-arginine (20 mg/kg, i.p., nitric-oxide synthase inhibitor) 15 min before AM (200 mg/kg, p.o.). The in vitro cyclooxygenase assay also showed that AM produced concentration-dependent inhibition of both cyclooxygenase (COX)-1 and COX-2 activity by 39.44%±0.05% and 55.71%±0.12%, respectively, at 100 μg/mL. In conclusion, A. muricata possesses analgesic effect through interaction with opioidergic pathway and anti-inflammatory property through inhibition of chemical mediators of inflammation. PMID:25133801

A&M. TAN607. Elevation for secondphase expansion of A&M Building. Work ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. TAN-607. Elevation for second-phase expansion of A&M Building. Work areas south of the Carpentry Shop. High-bay shop, decontamination room at south-most end. Approved by INEEL Classification Office for public release. Ralph M. Parsons 1299-5-ANP/GE-3-607-A 106. Date: August 1956. INEEL index code no. 034-0607-00-693-107166 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

High turnover of fungal hyphae in incubation experiments.

PubMed

de Vries, Franciska T; Bååth, Erland; Kuyper, Thom W; Bloem, Jaap

2009-03-01

Soil biological studies are often conducted on sieved soils without the presence of plants. However, soil fungi build delicate mycelial networks, often symbiotically associated with plant roots (mycorrhizal fungi). We hypothesized that as a result of sieving and incubating without plants, the total fungal biomass decreases. To test this, we conducted three incubation experiments. We expected total and arbuscular mycorrhizal (AM) fungal biomass to be higher in less fertilized soils than in fertilized soils, and thus to decrease more during incubation. Indeed, we found that fungal biomass decreased rapidly in the less fertilized soils. A shift towards thicker hyphae occurred, and the fraction of septate hyphae increased. However, analyses of phospholipid fatty acids (PLFAs) and neutral lipid fatty acids could not clarify which fungal groups were decreasing. We propose that in our soils, there was a fraction of fungal biomass that was sensitive to fertilization and disturbance (sieving, followed by incubation without plants) with a very high turnover (possibly composed of fine hyphae of AM and saprotrophic fungi), and a fraction that was much less vulnerable with a low turnover (composed of saprotrophic fungi and runner hyphae of AMF). Furthermore, PLFAs might not be as sensitive in detecting changes in fungal biomass as previously thought.

Transcriptome Profiling of Lotus japonicus Roots During Arbuscular Mycorrhiza Development and Comparison with that of Nodulation

PubMed Central

Deguchi, Yuichi; Banba, Mari; Shimoda, Yoshikazu; Chechetka, Svetlana A.; Suzuri, Ryota; Okusako, Yasuhiro; Ooki, Yasuhiro; Toyokura, Koichi; Suzuki, Akihiro; Uchiumi, Toshiki; Higashi, Shiro; Abe, Mikiko; Kouchi, Hiroshi; Izui, Katsura; Hata, Shingo

2007-01-01

Abstract To better understand the molecular responses of plants to arbuscular mycorrhizal (AM) fungi, we analyzed the differential gene expression patterns of Lotus japonicus, a model legume, with the aid of a large-scale cDNA macroarray. Experiments were carried out considering the effects of contaminating microorganisms in the soil inoculants. When the colonization by AM fungi, i.e. Glomus mosseae and Gigaspora margarita, was well established, four cysteine protease genes were induced. In situ hybridization revealed that these cysteine protease genes were specifically expressed in arbuscule-containing inner cortical cells of AM roots. On the other hand, phenylpropanoid biosynthesis-related genes for phenylalanine ammonia-lyase (PAL), chalcone synthase, etc. were repressed in the later stage, although they were moderately up-regulated on the initial association with the AM fungus. Real-time RT–PCR experiments supported the array experiments. To further confirm the characteristic expression, a PAL promoter was fused with a reporter gene and introduced into L. japonicus, and then the transformants were grown with a commercial inoculum of G. mosseae. The reporter activity was augmented throughout the roots due to the presence of contaminating microorganisms in the inoculum. Interestingly, G. mosseae only colonized where the reporter activity was low. Comparison of the transcriptome profiles of AM roots and nitrogen-fixing root nodules formed with Mesorhizobium loti indicated that the PAL genes and other phenylpropanoid biosynthesis-related genes were similarly repressed in the two organs. PMID:17634281

Biosorption of americium-241 by immobilized Rhizopus arrihizus.

PubMed

Liao, Jiali; Yang, Yuanyou; Luo, Shunzhong; Liu, Ning; Jin, Jiannan; Zhang, Taiming; Zhao, Pengji

2004-01-01

Rhizopus arrihizus (R. arrihizus), a fungus, which in previous experiments had shown encouraging ability to remove 241Am from solutions, was immobilized by calcium alginate and other reagents. The various factors affecting 241Am biosorption by the immobilized R. arrihizus were investigated. The results showed that not only can immobilized R. arrihizus adsorb 241Am as efficiently as free R. arrihizus, but that also can be used repeatedly or continuously. The biosorption equilibrium was achieved within 2 h, and more than 94% of 241Am was removed from 241Am solutions of 1.08 MBq/l by immobilized R. arrihizu in the pH range 1-7. Temperature did not affect the adsorption on immobilized R. arrihizus in the range 15-45 degrees C. After repeated adsorption for 8 times, the immobilized R. arrihizus still adsorbed more than 97% of 241Am. At this time, the total adsorption of 241Am was more than 88.6 KBq/g, and had not yet reached saturation. Ninety-five percent of the adsorbed 241Am was desorbed by saturated EDTA solution and 98% by 2 mol/l HNO(3).

Optimization of an Advanced Multi-Junction Solar-Cell Design for Space Environments (AM0) Using Nearly Orthogonal Latin Hypercubes

DTIC Science & Technology

2017-06-01

AN ADVANCED MULTI-JUNCTION SOLAR -CELL DESIGN FOR SPACE ENVIRONMENTS (AM0) USING NEARLY ORTHOGONAL LATIN HYPERCUBES by Silvio Pueschel June...ADVANCED MULTI-JUNCTION SOLAR -CELL DESIGN FOR SPACE ENVIRONMENTS (AM0) USING NEARLY ORTHOGONAL LATIN HYPERCUBES 5. FUNDING NUMBERS 6. AUTHOR(S) Silvio...multi-junction solar cells with Silvaco Atlas simulation software. It introduces the nearly orthogonal Latin hypercube (NOLH) design of experiments (DoE

Can energy drinks increase the desire for more alcohol?

PubMed

Marczinski, Cecile A

2015-01-01

Energy drinks, the fastest growing segment in the beverage market, have become popular mixers with alcohol. The emerging research examining the use of alcohol mixed with energy drinks (AmEDs) indicates that the combination of caffeine-containing energy drinks with alcohol may be riskier than the use of alcohol alone. The public health concerns arising from AmED use are documented in different research domains. Epidemiologic studies reveal that the consumption of AmEDs is frequent among young and underage drinkers, demographic groups that are more likely to experience the harms and hazards associated with alcohol use. In addition, for all consumers, elevated rates of binge drinking and risk of alcohol dependence have been associated with AmED use when compared to alcohol alone. Results from laboratory studies help explain why AmED use is associated with excessive intake of alcohol. When an energy drink (or caffeine) is combined with alcohol, the desire (or urge) to drink more alcohol is more pronounced in both humans and animals than with the same dose of alcohol alone. The experience of drinking alcohol appears to be more rewarding when combined with energy drinks. Given that caffeine in other foods and beverages increases preference for those products, further research on AmEDs may elucidate the underlying mechanisms that contribute to alcohol dependence. © 2015 American Society for Nutrition.

Cardiac effects of 3-iodothyronamine: a new aminergic system modulating cardiac function.

PubMed

Chiellini, Grazia; Frascarelli, Sabina; Ghelardoni, Sandra; Carnicelli, Vittoria; Tobias, Sandra C; DeBarber, Andrea; Brogioni, Simona; Ronca-Testoni, Simonetta; Cerbai, Elisabetta; Grandy, David K; Scanlan, Thomas S; Zucchi, Riccardo

2007-05-01

3-Iodothyronamine T1AM is a novel endogenous thyroid hormone derivative that activates the G protein-coupled receptor known as trace anime-associated receptor 1 (TAAR1). In the isolated working rat heart and in rat cardiomyocytes, T1AM produced a reversible, dose-dependent negative inotropic effect (e.g., 27+/-5, 51+/-3, and 65+/-2% decrease in cardiac output at 19, 25, and 38 microM concentration, respectively). An independent negative chronotropic effect was also observed. The hemodynamic effects of T1AM were remarkably increased in the presence of the tyrosine kinase inhibitor genistein, whereas they were attenuated in the presence of the tyrosine phosphatase inhibitor vanadate. No effect was produced by inhibitors of protein kinase A, protein kinase C, calcium-calmodulin kinase II, phosphatidylinositol-3-kinase, or MAP kinases. Tissue cAMP levels were unchanged. In rat ventricular tissue, Western blot experiments with antiphosphotyrosine antibodies showed reduced phosphorylation of microsomal and cytosolic proteins after perfusion with synthetic T1AM; reverse transcriptase-polymerase chain reaction experiments revealed the presence of transcripts for at least 5 TAAR subtypes; specific and saturable binding of [125I]T1AM was observed, with a dissociation constant in the low micromolar range (5 microM); and endogenous T1AM was detectable by tandem mass spectrometry. In conclusion, our findings provide evidence for the existence of a novel aminergic system modulating cardiac function.

Characterization of a mine fire using atmospheric monitoring system sensor data.

PubMed

Yuan, L; Thomas, R A; Zhou, L

2017-06-01

Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the United States for the detection of fire in the belt entry and the monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data have the potential to provide fire characteristic information such as fire growth - in terms of heat release rate - and exact fire location. Such information is critical in making decisions regarding fire-fighting strategies, underground personnel evacuation and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide concentration, carbon dioxide concentration and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division's Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy.

Assessment of rhythmic entrainment at multiple timescales in dyslexia: evidence for disruption to syllable timing.

PubMed

Leong, Victoria; Goswami, Usha

2014-02-01

Developmental dyslexia is associated with rhythmic difficulties, including impaired perception of beat patterns in music and prosodic stress patterns in speech. Spoken prosodic rhythm is cued by slow (<10 Hz) fluctuations in speech signal amplitude. Impaired neural oscillatory tracking of these slow amplitude modulation (AM) patterns is one plausible source of impaired rhythm tracking in dyslexia. Here, we characterise the temporal profile of the dyslexic rhythm deficit by examining rhythmic entrainment at multiple speech timescales. Adult dyslexic participants completed two experiments aimed at testing the perception and production of speech rhythm. In the perception task, participants tapped along to the beat of 4 metrically-regular nursery rhyme sentences. In the production task, participants produced the same 4 sentences in time to a metronome beat. Rhythmic entrainment was assessed using both traditional rhythmic indices and a novel AM-based measure, which utilised 3 dominant AM timescales in the speech signal each associated with a different phonological grain-sized unit (0.9-2.5 Hz, prosodic stress; 2.5-12 Hz, syllables; 12-40 Hz, phonemes). The AM-based measure revealed atypical rhythmic entrainment by dyslexic participants to syllable patterns in speech, in perception and production. In the perception task, both groups showed equally strong phase-locking to Syllable AM patterns, but dyslexic responses were entrained to a significantly earlier oscillatory phase angle than controls. In the production task, dyslexic utterances showed shorter syllable intervals, and differences in Syllable:Phoneme AM cross-frequency synchronisation. Our data support the view that rhythmic entrainment at slow (∼5 Hz, Syllable) rates is atypical in dyslexia, suggesting that neural mechanisms for syllable perception and production may also be atypical. These syllable timing deficits could contribute to the atypical development of phonological representations for spoken words, the central cognitive characteristic of developmental dyslexia across languages. Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

Establishing nurse-led active surveillance for men with localised prostate cancer: development and formative evaluation of a model of care in the ProtecT trial.

PubMed

Wade, Julia; Holding, Peter N; Bonnington, Susan; Rooshenas, Leila; Lane, J Athene; Salter, C Elizabeth; Tilling, Kate; Speakman, Mark J; Brewster, Simon F; Evans, Simon; Neal, David E; Hamdy, Freddie C; Donovan, Jenny L

2015-09-18

To develop a nurse-led, urologist-supported model of care for men managed by active surveillance or active monitoring (AS/AM) for localised prostate cancer and provide a formative evaluation of its acceptability to patients, clinicians and nurses. Nurse-led care, comprising an explicit nurse-led protocol with support from urologists, was developed as part of the AM arm of the Prostate testing for cancer and Treatment (ProtecT) trial. Interviews and questionnaire surveys of clinicians, nurses and patients assessed acceptability. Nurse-led clinics were established in 9 centres in the ProtecT trial and compared with 3 non-ProtecT urology centres elsewhere in UK. Within ProtecT, 22 men receiving AM nurse-led care were interviewed about experiences of care; 11 urologists and 23 research nurses delivering ProtecT trial care completed a questionnaire about its acceptability; 20 men managed in urology clinics elsewhere in the UK were interviewed about models of AS/AM care; 12 urologists and three specialist nurses working in these clinics were also interviewed about management of AS/AM. Nurse-led care was commended by ProtecT trial participants, who valued the flexibility, accessibility and continuity of the service and felt confident about the quality of care. ProtecT consultant urologists and nurses also rated it highly, identifying continuity of care and resource savings as key attributes. Clinicians and patients outside the ProtecT trial believed that nurse-led care could relieve pressure on urology clinics without compromising patient care. The ProtecT AM nurse-led model of care was acceptable to men with localised prostate cancer and clinical specialists in urology. The protocol is available for implementation; we aim to evaluate its impact on routine clinical practice. NCT02044172; ISRCTN20141297. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Assessment of rhythmic entrainment at multiple timescales in dyslexia: Evidence for disruption to syllable timing☆

PubMed Central

Leong, Victoria; Goswami, Usha

2014-01-01

Developmental dyslexia is associated with rhythmic difficulties, including impaired perception of beat patterns in music and prosodic stress patterns in speech. Spoken prosodic rhythm is cued by slow (<10 Hz) fluctuations in speech signal amplitude. Impaired neural oscillatory tracking of these slow amplitude modulation (AM) patterns is one plausible source of impaired rhythm tracking in dyslexia. Here, we characterise the temporal profile of the dyslexic rhythm deficit by examining rhythmic entrainment at multiple speech timescales. Adult dyslexic participants completed two experiments aimed at testing the perception and production of speech rhythm. In the perception task, participants tapped along to the beat of 4 metrically-regular nursery rhyme sentences. In the production task, participants produced the same 4 sentences in time to a metronome beat. Rhythmic entrainment was assessed using both traditional rhythmic indices and a novel AM-based measure, which utilised 3 dominant AM timescales in the speech signal each associated with a different phonological grain-sized unit (0.9–2.5 Hz, prosodic stress; 2.5–12 Hz, syllables; 12–40 Hz, phonemes). The AM-based measure revealed atypical rhythmic entrainment by dyslexic participants to syllable patterns in speech, in perception and production. In the perception task, both groups showed equally strong phase-locking to Syllable AM patterns, but dyslexic responses were entrained to a significantly earlier oscillatory phase angle than controls. In the production task, dyslexic utterances showed shorter syllable intervals, and differences in Syllable:Phoneme AM cross-frequency synchronisation. Our data support the view that rhythmic entrainment at slow (∼5 Hz, Syllable) rates is atypical in dyslexia, suggesting that neural mechanisms for syllable perception and production may also be atypical. These syllable timing deficits could contribute to the atypical development of phonological representations for spoken words, the central cognitive characteristic of developmental dyslexia across languages. This article is part of a Special Issue entitled . PMID:23916752

Establishing nurse-led active surveillance for men with localised prostate cancer: development and formative evaluation of a model of care in the ProtecT trial

PubMed Central

Wade, Julia; Holding, Peter N; Bonnington, Susan; Rooshenas, Leila; Lane, J Athene; Salter, C Elizabeth; Tilling, Kate; Speakman, Mark J; Brewster, Simon F; Evans, Simon; Neal, David E; Hamdy, Freddie C; Donovan, Jenny L

2015-01-01

Objectives To develop a nurse-led, urologist-supported model of care for men managed by active surveillance or active monitoring (AS/AM) for localised prostate cancer and provide a formative evaluation of its acceptability to patients, clinicians and nurses. Nurse-led care, comprising an explicit nurse-led protocol with support from urologists, was developed as part of the AM arm of the Prostate testing for cancer and Treatment (ProtecT) trial. Design Interviews and questionnaire surveys of clinicians, nurses and patients assessed acceptability. Setting Nurse-led clinics were established in 9 centres in the ProtecT trial and compared with 3 non-ProtecT urology centres elsewhere in UK. Participants Within ProtecT, 22 men receiving AM nurse-led care were interviewed about experiences of care; 11 urologists and 23 research nurses delivering ProtecT trial care completed a questionnaire about its acceptability; 20 men managed in urology clinics elsewhere in the UK were interviewed about models of AS/AM care; 12 urologists and three specialist nurses working in these clinics were also interviewed about management of AS/AM. Results Nurse-led care was commended by ProtecT trial participants, who valued the flexibility, accessibility and continuity of the service and felt confident about the quality of care. ProtecT consultant urologists and nurses also rated it highly, identifying continuity of care and resource savings as key attributes. Clinicians and patients outside the ProtecT trial believed that nurse-led care could relieve pressure on urology clinics without compromising patient care. Conclusions The ProtecT AM nurse-led model of care was acceptable to men with localised prostate cancer and clinical specialists in urology. The protocol is available for implementation; we aim to evaluate its impact on routine clinical practice. Trial registration numbers NCT02044172; ISRCTN20141297. PMID:26384727

Higher Americium Oxidation State Research Roadmap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mincher, Bruce J.; Law, Jack D.; Goff, George S.

2015-12-18

The partitioning of hexavalent Am from dissolved nuclear fuel requires the ability to efficiently oxidize Am(III) to Am(VI) and to maintain that oxidation state for a length of time sufficient to perform the separation. Several oxidants have been, or are being developed. Chemical oxidants include Ag-catalyzed ozone, Ag-catalyzed peroxydisulfate, Cu(III) periodate, and sodium bismuthate. Hexavalent americium has also now successfully been prepared by electrolysis, using functionalized electrodes. So-called auto-reduction rates of Am(VI) are sufficiently slow to allow for separations. However, for separations based on solvent extraction or ion exchange using organic resins, the high valence state must be maintained undermore » the reducing conditions of the organic phase contact, and a holding oxidant is probably necessary. Until now, only Cu(III) periodate and sodium bismuthate oxidation have been successfully combined with solvent extraction separations. Bismuthate oxidation provided the higher DAm, since it acts as its own holding oxidant, and a successful hot test using centrifugal contactors was performed. For the other oxidants, Ag-catalyzed peroxydisulfate will not oxidize americium in nitric acid concentrations above 0.3 M, and it is not being further investigated. Peroxydisulfate in the absence of Ag catalysis is being used to prepare Am(V) in ion exchange work, discussed below. Preliminary work with Ag-catalyzed ozone has been unsuccessful for extractions of Am(VI) from 6.5 M HNO3, and only one attempt at extraction, also from 6.5 M HNO3, using the electrolytic oxidation has been attempted. However, this high acid concentration was based on the highest Am extraction efficiency using the bismuthate oxidant; which is only sparingly soluble, and thus the oxidation yield is based on bismuthate solubility. Lower acid concentrations may be sufficient with alternative oxidants and work with Ag-ozone, Cu(III) and electrolysis is on-going. Two non-solvent-extraction separations are also under investigation. The first would separate Am(VI) by co-crystallization with uranium and the other oxidizable actinides as their nitrate salts. This novel idea has been successful in lab scale testing, and merits further investigation. Similarly, success has been achieved in separations using inorganic or hybrid ion exchange materials to sorb the lanthanides and actinides, while allowing pentavalent americium to elute. This is the only technique currently investigating Am(V), despite the advantages of this oxidation state with regard to its higher stability. The ultimate destination for this roadmap is to develop an americium separation that can be applied under process conditions, preferably affording a co-separation of the actinyl (VI) ions. Toward that end, emphasis is given here to selection of a solvent extraction flowsheet for testing in the INL centrifugal contactor hot test bed during FY16. A solvent extraction process will be tested mainly because solvent extraction separations of Am(VI) are relatively mature and the test bed currently exists in a configuration to support them. Thus, a major goal of FY16 is to select the oxidant/ligand combination to run such a test using the contactors. The only ligands under consideration are DAAP and DEHBA. This is not to say that ion exchange and co-crystallization techniques are unimportant. They merit continued investigation, but are not mature enough for hot test bed testing at this time.« less

78 FR 52128 - Cotton Classing, Testing and Standards: Notice of Request for an Extension and Revision to a...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-22

... DEPARTMENT OF AGRICULTURE Agricultural Marketing Service [AMS-CN-13-0044] Cotton Classing, Testing..., for an extension and revision to the currently approved information collection entitled Cotton... proposal to: Shethir M. Riva, Chief, Research and Promotion Staff, Cotton and Tobacco Programs, AMS, USDA...

78 FR 23884 - Seed Testing Service Program; Request for an Extension of and Revision to a Currently Approved...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-23

... Marketing Service's (AMS) intention to request approval from the Office of Management and Budget (OMB), for... DEPARTMENT OF AGRICULTURE Agricultural Marketing Service [Doc. No. AMS-LS-13-0007] Seed Testing... AGENCY: Agricultural Marketing Service, USDA. ACTION: Request for comments. SUMMARY: In accordance with...

Arbuscular mycorrhiza improve growth, nitrogen uptake, and nitrogen use efficiency in wheat grown under elevated CO2.

PubMed

Zhu, Xiancan; Song, Fengbin; Liu, Shengqun; Liu, Fulai

2016-02-01

Effects of the arbuscular mycorrhizal (AM) fungus Rhizophagus irregularis on plant growth, carbon (C) and nitrogen (N) accumulation, and partitioning was investigated in Triticum aestivum L. plants grown under elevated CO2 in a pot experiment. Wheat plants inoculated or not inoculated with the AM fungus were grown in two glasshouse cells with different CO2 concentrations (400 and 700 ppm) for 10 weeks. A (15)N isotope labeling technique was used to trace plant N uptake. Results showed that elevated CO2 increased AM fungal colonization. Under CO2 elevation, AM plants had higher C concentration and higher plant biomass than the non-AM plants. CO2 elevation did not affect C and N partitioning in plant organs, while AM symbiosis increased C and N allocation into the roots. In addition, plant C and N accumulation, (15)N recovery rate, and N use efficiency (NUE) were significantly higher in AM plants than in non-AM controls under CO2 enrichment. It is concluded that AM symbiosis favors C and N partitioning in roots, increases C accumulation and N uptake, and leads to greater NUE in wheat plants grown at elevated CO2.

Spectral and temporal resolutions of information-bearing acoustic changes for understanding vocoded sentencesa)

PubMed Central

Stilp, Christian E.; Goupell, Matthew J.

2015-01-01

Short-time spectral changes in the speech signal are important for understanding noise-vocoded sentences. These information-bearing acoustic changes, measured using cochlea-scaled entropy in cochlear implant simulations [CSECI; Stilp et al. (2013). J. Acoust. Soc. Am. 133(2), EL136–EL141; Stilp (2014). J. Acoust. Soc. Am. 135(3), 1518–1529], may offer better understanding of speech perception by cochlear implant (CI) users. However, perceptual importance of CSECI for normal-hearing listeners was tested at only one spectral resolution and one temporal resolution, limiting generalizability of results to CI users. Here, experiments investigated the importance of these informational changes for understanding noise-vocoded sentences at different spectral resolutions (4–24 spectral channels; Experiment 1), temporal resolutions (4–64 Hz cutoff for low-pass filters that extracted amplitude envelopes; Experiment 2), or when both parameters varied (6–12 channels, 8–32 Hz; Experiment 3). Sentence intelligibility was reduced more by replacing high-CSECI intervals with noise than replacing low-CSECI intervals, but only when sentences had sufficient spectral and/or temporal resolution. High-CSECI intervals were more important for speech understanding as spectral resolution worsened and temporal resolution improved. Trade-offs between CSECI and intermediate spectral and temporal resolutions were minimal. These results suggest that signal processing strategies that emphasize information-bearing acoustic changes in speech may improve speech perception for CI users. PMID:25698018

Inorganic Salt Interference on CO2+ in Aerodyne AMS and ACSM Organic Aerosol Composition Studies.

PubMed

Pieber, Simone M; El Haddad, Imad; Slowik, Jay G; Canagaratna, Manjula R; Jayne, John T; Platt, Stephen M; Bozzetti, Carlo; Daellenbach, Kaspar R; Fröhlich, Roman; Vlachou, Athanasia; Klein, Felix; Dommen, Josef; Miljevic, Branka; Jiménez, José L; Worsnop, Douglas R; Baltensperger, Urs; Prévôt, André S H

2016-10-04

Aerodyne aerosol mass spectrometer (AMS) and Aerodyne aerosol chemical speciation monitor (ACSM) mass spectra are widely used to quantify organic aerosol (OA) elemental composition, oxidation state, and major environmental sources. The OA CO 2 + fragment is among the most important measurements for such analyses. Here, we show that a non-OA CO 2 + signal can arise from reactions on the particle vaporizer, ion chamber, or both, induced by thermal decomposition products of inorganic salts. In our tests (eight instruments, n = 29), ammonium nitrate (NH 4 NO 3 ) causes a median CO 2 + interference signal of +3.4% relative to nitrate. This interference is highly variable between instruments and with measurement history (percentiles P 10-90 = +0.4 to +10.2%). Other semi-refractory nitrate salts showed 2-10 times enhanced interference compared to that of NH 4 NO 3 , while the ammonium sulfate ((NH 4 ) 2 SO 4 ) induced interference was 3-10 times lower. Propagation of the CO 2 + interference to other ions during standard AMS and ACSM data analysis affects the calculated OA mass, mass spectra, molecular oxygen-to-carbon ratio (O/C), and f 44 . The resulting bias may be trivial for most ambient data sets but can be significant for aerosol with higher inorganic fractions (>50%), e.g., for low ambient temperatures, or laboratory experiments. The large variation between instruments makes it imperative to regularly quantify this effect on individual AMS and ACSM systems.

Magnetic fabric of sheared till: A strain indicator for evaluating the bed deformation model of glacier flow

USGS Publications Warehouse

Hooyer, T.S.; Iverson, N.R.; Lagroix, F.; Thomason, J.F.

2008-01-01

Wet-based portions of ice sheets may move primarily by shearing their till beds, resting in high sediment fluxes and the development of subglacial landforms. This model of glacier movement, which requires high bed shear strains, can be tested using till microstructural characteristics that evolve during till deformation. Here we examine the development of magnetic fabric using a ring shear device to defom two Wisconsin-age basal tills to shear strains as high as 70. Hysteresis experiments and the dependence of magnetic susceptibility of these tills on temperature demonstrate that anisotropy of magnetic susceptibility (AMS) develops during shear due to the rotation of primarily magnetite particles that are silt sized or smaller. At moderate shear strains (???6-25), principal axes of maximum magnetic susceptibility develop a strong fabric (S1 eignevalues of 0.83-0.96), without further strengthening at higher strains, During deformation, directions of maximum susceptibility cluster strongly in the direction of shear and plunge 'up-glacier,' consistent with the behavior of pebbles and sand particles studied in earlier experiments. In contrast, the magnitude of AMS does not vary systematically with strain and is small relative to its variability among samples; this is because most magnetite grains are contained as inclusions in larger particles and hence do not align during shear. Although processes other than pervasive bed deformation may result in strong flow parallel fabrics, AMS fabrics provide a rapid and objective means of identifying basal tills that have not been sheared sufficiently to be compatible with the bed deformation model. Copyright 2008 by the American Geophysical Union.

Trait differences in responses to arbuscular mycorrhizal fungi are stronger and more consistent than fixed differences among populations of Asclepias speciosa.

PubMed

Waller, Lauren P; Hahn, Philip G; Maron, John L; Lekberg, Ylva

2018-02-01

Arbuscular mycorrhizal (AM) fungi can promote plant growth and reproduction, but other plant physiological traits or traits that provide defense against herbivores can also be affected by AM fungi. However, whether responses of different traits to AM fungi are correlated and whether these relationships vary among plants from different populations are unresolved. In a common garden experiment, we grew Asclepias speciosa plants from seed collected from populations found along an environmental gradient with and without AM fungi to assess whether the responses of six growth and defense traits to AM fungi are correlated. Although there was strong genetic differentiation in mean trait values among populations, AM fungi consistently increased expression of most growth and defense traits across all populations. Responses of biomass and root to shoot ratio to AM fungi were positively correlated, suggesting that plants that are more responsive to AM fungi allocated more biomass belowground. Responses of biomass and trichome density to AM fungi were negatively correlated, indicating a trade-off in responsiveness between a growth and defensive trait. Our results suggest that while there is substantial population differentiation in many traits of A. speciosa, populations respond similarly to AM fungi, and both positive and negative correlations among trait responses occur. © 2018 Botanical Society of America.

KSC-2010-5391

NASA Image and Video Library

2010-11-01

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the Alpha Magnetic Spectrometer-2 (AMS) will be rotated 180 degrees to provide better access for work to be performed on its avionics box. Technicians also will install a flight releasable grappling fixture to AMS while it is upside down. AMS is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch Feb. 27, 2011. Photo credit: NASA/Jack Pfaller

KSC-2010-5400

NASA Image and Video Library

2010-11-01

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the Alpha Magnetic Spectrometer-2 (AMS) will be rotated 180 degrees to provide better access for work to be performed on its avionics box. Technicians also will install a flight releasable grappling fixture to AMS while it is upside down. AMS is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch Feb. 27, 2011. Photo credit: NASA/Jack Pfaller

KSC-2010-5395

NASA Image and Video Library

2010-11-01

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the Alpha Magnetic Spectrometer-2 (AMS) rotates 180 degrees to provide better access for work to be performed on its avionics box. Technicians also will install a flight releasable grappling fixture to AMS while it is upside down. AMS is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch Feb. 27, 2011. Photo credit: NASA/Jack Pfaller

KSC-2010-5396

NASA Image and Video Library

2010-11-01

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the Alpha Magnetic Spectrometer-2 (AMS) is positioned at a 180-degree angle to provide better access for work to be performed on its avionics box. Technicians also will install a flight releasable grappling fixture to AMS while it is upside down. AMS is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch Feb. 27, 2011. Photo credit: NASA/Jack Pfaller

KSC-2010-5399

NASA Image and Video Library

2010-11-01

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the Alpha Magnetic Spectrometer-2 (AMS) rotates 180 degrees to provide better access for work to be performed on its avionics box. Technicians also will install a flight releasable grappling fixture to AMS while it is upside down. AMS is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch Feb. 27, 2011. Photo credit: NASA/Jack Pfaller

Immediate hypersensitivity reaction following liposomal amphotericin-B (AmBisome) infusion

PubMed Central

Nath, Proggananda; Harada, Michiyo; Sarkar, Santana; Selim, Shahjada; Maude, Richard J; Noiri, Eisei; Faiz, Abul

2014-01-01

Liposomal amphotericin-B (AmBisome) is now becoming first choice for the treatment of visceral leishmaniasis (kala-azar) patients due to high efficacy and less toxicity. The reported incidence of hypersensitivity reactions to liposomal amphotericin-B (AmBisome), especially during therapy, is very rare. We report two patients with kala-azar: one developed breathing difficulties and hypotension followed by shock and the other had facial angioedema with chest tightness during treatment. Both patients were managed with immediate action of injection: adrenaline, diphenhydramine and hydrocortisone. In our experience, AmBisome can cause severe hypersensitivity reactions that warrant proper support and close supervision. PMID:25139411

Pan American World Airways flight training: A new direction. Flight operations resource management

NASA Technical Reports Server (NTRS)

Butler, Roy

1987-01-01

The Pan Am Flight Training Department shares the experiences it is having in its attempt to integrate cockpit resource management philosophies into its training programs. A slide-tape presentation on Pan Am's new direction in flight training is presented and briefly discussed.

Selection of Additive Manufacturing (AM) Equipment

DTIC Science & Technology

2017-04-01

in the design , test, and fabrication of the systems within the AMRDEC portfolio. 14. SUBJECT TERMS Additive Manufacturing (AM), Fused Deposition...tools in the design and development of AMRDEC products .   Figure 1. Stratasys Objet Connex3 [1] While these machines and technologies have...TECHNICAL REPORT RDMR-WD-16-87 SELECTION OF ADDITIVE MANUFACTURING (AM) EQUIPMENT Lance E. Hall Weapons Development

Explosives mimic for testing, training, and monitoring

DOEpatents

Reynolds, John G.; Durban, Matthew M.; Gash, Alexander E.; Grapes, Michael D.; Kelley, Ryan S.; Sullivan, Kyle T.

2018-02-13

Additive Manufacturing (AM) is used to make mimics for explosives. The process uses mixtures of explosives and matrices commonly used in AM. The explosives are formulated into a mixture with the matrix and printed using AM techniques and equipment. The explosive concentrations are kept less than 10% by wt. of the mixture to conform to requirements of shipping and handling.

Using mental visual imagery to improve autobiographical memory and episodic future thinking in relapsing-remitting multiple sclerosis patients: A randomised-controlled trial study.

PubMed

Ernst, Alexandra; Blanc, Frédéric; De Seze, Jérôme; Manning, Liliann

2015-01-01

The co-occurrence of autobiographical memory (AM) and episodic future thinking (EFT) impairment has been documented in relapsing-remitting multiple sclerosis (RR-MS) patients. On these bases, we aimed at probing the efficacy of a mental visual imagery (MVI)-based facilitation programme on AM and EFT functioning in the context of a randomised-controlled trial study in RR-MS patients. Using the Autobiographical Interview (AI), 40 patients presenting with an AM/EFT impairment were randomly assigned in three groups: (i) the experimental (n = 17), who followed the MVI programme, (ii) the verbal control (n = 10), who followed a sham verbal programme, and (iii) the stability groups (n = 13), who underwent the AM/EFT test twice, with no intervention in between. AI's second assessment scores showed a significant improvement of AM and EFT performance only for the experimental group, with a long-term robustness of treatment benefits. The control and stability groups' results ruled out nursing and test learning effects as explanations of AM/EFT improvement. These benefits were corroborated by the patients' comments, which indicated an effective MVI strategy transfer to daily life. Our results suggest that the MVI programme tackles a common cognitive process of scene construction present in AM and EFT.

Status, technology and development of silicon solar cells at INER

NASA Astrophysics Data System (ADS)

Jao, S. S.; Tseng, H. H.; Cheng, C.; Tzeng, Y. C.; Chang, H. H.; Hwang, H. L.

Test runs using 200 5-cm-diameter silicon wafers are carried out, yielding 87% with an AM1 conversion efficiency greater than 11.5%. The highest efficiency is 12.7%. Concentrator solar cells of 2 x 2 sq cm are made with an AM1 efficiency of 14%. Solar cells with a diameter of 7.5 cm have attained AM1 efficiencies of more than 11.3%, and texturized solar cells of the same diameter fabricated from rejected wafers show AM1 efficiencies of 9.5-10.5%. It is noted that solar panels comprising 68 cells with a maximum output power of 13.5 W have been manufactured. The results of a 6-month test of a photovoltaic charge station for electric motorcycles are reported.

Stability and Control. Volume 2. Stability and Control Flight Test Theory

DTIC Science & Technology

1974-07-01

e we have 2 mx , . mx , mx n am e + bme + ce = 0 or (am2 + bm + c)emx = 0 (1.21) mx , n Since e ? 0...1.97) (1.98) Substituting 2 mt , , mt , mt n am e + bme + ce =0 (1.99) and emt (am2 + bm + c) =0 (1.100) led us to assert that 1.98 would...derive Laplace transforms each time we use them. Extensive tables of transforms exist in most advanced mathe- matics and control system textbooks . We

Science is innate!

DOE PAGES

Gilbert, Jack A.

2014-10-02

I am a professional scientist. What does that mean? I think it is safe to say it means that, to the best of my ability, I apply the scientist method to test hypotheses and gain a clearer understanding of the world around me. Furthermore, I am also a human being, and so when I am asked, as I often am, about how my research findings have influenced my day-to-day activities, I like to take a step back and think about what it means to be a scientist.

Prophylactic Acetaminophen or Ibuprofen Results in Equivalent Acute Mountain Sickness Incidence at High Altitude: A Prospective Randomized Trial.

PubMed

Kanaan, Nicholas C; Peterson, Alicia L; Pun, Matiram; Holck, Peter S; Starling, Jennifer; Basyal, Bikash; Freeman, Thomas F; Gehner, Jessica R; Keyes, Linda; Levin, Dana R; O'Leary, Catherine J; Stuart, Katherine E; Thapa, Ghan B; Tiwari, Aditya; Velgersdyk, Jared L; Zafren, Ken; Basnyat, Buddha

2017-06-01

Recent trials have demonstrated the usefulness of ibuprofen in the prevention of acute mountain sickness (AMS), yet the proposed anti-inflammatory mechanism remains unconfirmed. Acetaminophen and ibuprofen were tested for AMS prevention. We hypothesized that a greater clinical effect would be seen from ibuprofen due to its anti-inflammatory effects compared with acetaminophen's mechanism of possible symptom reduction by predominantly mediating nociception in the brain. A double-blind, randomized trial was conducted testing acetaminophen vs ibuprofen for the prevention of AMS. A total of 332 non-Nepali participants were recruited at Pheriche (4371 m) and Dingboche (4410 m) on the Everest Base Camp trek. The participants were randomized to either acetaminophen 1000 mg or ibuprofen 600 mg 3 times a day until they reached Lobuche (4940 m), where they were reassessed. The primary outcome was AMS incidence measured by the Lake Louise Questionnaire score. Data from 225 participants who met inclusion criteria were analyzed. Twenty-five participants (22.1%) in the acetaminophen group and 18 (16.1%) in the ibuprofen group developed AMS (P = .235). The combined AMS incidence was 19.1% (43 participants), 14 percentage points lower than the expected AMS incidence of untreated trekkers in prior studies at this location, suggesting that both interventions reduced the incidence of AMS. We found little evidence of any difference between acetaminophen and ibuprofen groups in AMS incidence. This suggests that AMS prevention may be multifactorial, affected by anti-inflammatory inhibition of the arachidonic-acid pathway as well as other analgesic mechanisms that mediate nociception. Additional study is needed. Copyright © 2017 Wilderness Medical Society. Published by Elsevier Inc. All rights reserved.

Testing the CaR-FA-X model: investigating the mechanisms underlying reduced autobiographical memory specificity in individuals with and without a history of depression.

PubMed

Sumner, Jennifer A; Mineka, Susan; Adam, Emma K; Craske, Michelle G; Vrshek-Schallhorn, Suzanne; Wolitzky-Taylor, Kate; Zinbarg, Richard E

2014-08-01

Reduced autobiographical memory specificity (AMS) is an important cognitive phenomenon in major depressive disorder (MDD), but knowledge about mechanisms is lacking. The CaR-FA-X model of Williams and colleagues (2007) proposed that 3 processes contributed to reduce AMS: capture and rumination (CaR), functional avoidance (FA), and impaired executive control (X). However, the entire CaR-FA-X model has not been tested. We addressed this gap in the literature by investigating contributions of the CaR-FA-X mechanisms to reduced AMS, alone or in interaction, in a subset of young adults (N = 439) from the Northwestern-UCLA Youth Emotion Project. Participants were classified as those with (n = 164) and without (n = 275) a history of MDD at AMS assessment. They completed measures of: AMS; rumination (the brooding factor; CaR); childhood, adolescent, and early adulthood adversity (FA); avoidant coping (FA); and verbal fluency (X). Using structural equation modeling, we found greatest support for associations between reduced AMS and the capture and rumination, and impaired executive control mechanisms. In those with and without a history of MDD, brooding and verbal fluency interacted to contribute to reduced AMS. For participants without a history of MDD, lower verbal fluency (indicating impaired executive control) was associated with reduced AMS among those high on brooding. For participants with a history of MDD, lower verbal fluency was associated with reduced AMS among those low on brooding. The first finding was consistent with the CaR-FA-X model but the latter was not. Implications for conceptualizations of reduced AMS and its mechanisms are discussed. (c) 2014 APA, all rights reserved.

AMS results on the fluxes of light nuclei in cosmic rays

NASA Astrophysics Data System (ADS)

Bertucci, Bruna; AMS Collaboration

2017-01-01

AMS-02 is a wide acceptance high-energy physics experiment installed on the International Space Station in May 2011 and it has been operating continuously since then. AMS-02 is able to separate cosmic rays light nuclei species (1 <= Z <= 8) with contaminations less than 10-3 thanks to the redundant measurement of the particle charge in eight silicon tracker layers, four scintillator planes and the Ring Imaging Cherenkov detector. The accurate measure of their spectrum in the GeV-TeV range is performed by the magnetic spectrometer with a maximum detectable rigidity of 2-3 TV. Precise measurements from AMS will be presented, including proton, helium, boron to carbon flux ratio, and highlights of ongoing analyses discussed. On behalf of the AMS Collaboration.

Recovery of rat alveolar macrophages by bronchoalveolar lavage under normal and activated conditions.

PubMed Central

Rehn, B; Bruch, J; Zou, T; Hobusch, G

1992-01-01

When rat (female Wistar) lungs were lavaged (bronchoalveolar lavage, BAL) six times with physiological saline, approximately the same number of alveolar macrophages (AM) were found in the first and second BAL, whereas in the third fourth, fifth, and sixth BAL, the number of AM decreased exponentially. Morphometric counting of the number of AM in histological sections of lung tissue showed that only 14% of the AM population had been recovered by BAL. Although additives to the BAL fluid such as lidocaine and/or fetal calf serum increased the AM count in the first washing considerably, the total number of AM washed out remained unaltered. Addition of the phagocytosis stimulant zymosan increased the AM count in BAL by a factor of more than 2. On stimulation of the lungs with an inert dust (silicon carbide), the AM count in the BAL and the lung was only slightly increased 8 weeks after intratracheal instillation. In contrast, after exposure to fibrogenic and cytotoxic quartz, the AM count in BAL and lung was significantly increased, and the recovery of AM had also increased by a factor of approximately 2. The experiments show that it is the micromilieu of the alveoli and the condition of the AM (certain physiological activation states, such as phagocytic activity) that essentially determine the degree of recovery. PMID:1396444

Development of the Accelerator Mass Spectrometry technology at the Comenius University in Bratislava

NASA Astrophysics Data System (ADS)

Povinec, Pavel P.; Masarik, Jozef; Ješkovský, Miroslav; Kaizer, Jakub; Šivo, Alexander; Breier, Robert; Pánik, Ján; Staníček, Jaroslav; Richtáriková, Marta; Zahoran, Miroslav; Zeman, Jakub

2015-10-01

An Accelerator Mass Spectrometry (AMS) laboratory has been established at the Centre for Nuclear and Accelerator Technologies (CENTA) at the Comenius University in Bratislava comprising of a MC-SNICS ion source, 3 MV Pelletron tandem accelerator, and an analyzer of accelerated ions. The preparation of targets for 14C and 129I AMS measurements is described in detail. The development of AMS techniques for potassium, uranium and thorium analysis in radiopure materials required for ultra-low background underground experiments is briefly mentioned.

EOS-AM precision pointing verification

NASA Technical Reports Server (NTRS)

Throckmorton, A.; Braknis, E.; Bolek, J.

1993-01-01

The Earth Observing System (EOS) AM mission requires tight pointing knowledge to meet scientific objectives, in a spacecraft with low frequency flexible appendage modes. As the spacecraft controller reacts to various disturbance sources and as the inherent appendage modes are excited by this control action, verification of precision pointing knowledge becomes particularly challenging for the EOS-AM mission. As presently conceived, this verification includes a complementary set of multi-disciplinary analyses, hardware tests and real-time computer in the loop simulations, followed by collection and analysis of hardware test and flight data and supported by a comprehensive data base repository for validated program values.

Development of an AMS method to study oceanic circulation characteristics using cosmogenic 39Ar

USGS Publications Warehouse

Collon, P.H.; Bichler, M.; Caggiano, J.; Cecil, L.D.; El, Masri Y.; Golser, R.; Jiang, C.L.; Heinz, A.; Henderson, D.; Kutschera, W.; Lehmann, B.E.; Leleux, P.; Loosli, H.H.; Pardo, R.C.; Paul, M.; Rehm, K.E.; Schlosser, P.; Scott, R.H.; Smethie, W.M.; Vondrasek, R.

2004-01-01

Initial experiments at the ATLAS facility [Nucl. Instr. and Meth. B 92 (1994) 241] resulted in a clear detection of cosmogenic 39Ar signal at the natural level. The present paper summarizes the recent developments of 39Ar AMS measurements at ATLAS: the use of an electron cyclotron resonance (ECR) positive ion source equipped with a special quartz liner to reduce 39K background, the development of a gas handling system for small volume argon samples, the acceleration of 39Ar8+ ions to 232 MeV, and the final separation of 39Ar from 39K in a gas-filled spectrograph. The first successful AMS measurements of 39Ar in ocean water samples from the Southern Atlantic ventilation experiment (SAVE) are reported. Published by Elsevier B.V.

How to Manage an Extensive Laserdisk Installation: The Texas A&M Experience.

ERIC Educational Resources Information Center

Tucker, Sandra L.; And Others

1988-01-01

The second of two articles on the acquisition and implementation of a large laserdisk service at Texas A&M University covers equipment and supplies, future plans, service, staffing, training of staff and patrons, and statistics. A floor plan, user instruction sheet, and news release are included. (MES)

How To Organize an Extensive Laserdisk Installation: The Texas A&M Experience.

ERIC Educational Resources Information Center

Jackson, Kathy M.; And Others

1988-01-01

The first of two articles on the acquisition and implementation of a large laserdisk service at Texas A&M University covers funding, donor recognition, selection and ordering of databases, planning and integrating the service with other information services, and future funding and plans. (5 references) (MES)

Psychoacoustics and Passive Sonar Detection

DTIC Science & Technology

1974-09-09

al., 1956; Veniar, 1958; Swets, Shipley, McKey und Gree^., 1959; Creelman , 1960; Green, 1961; and Gundy, 1961). In general, the experiments first...Acoust. Soc. Am. 3_7. 1064, (1965). 5. CD. Creelman , "Detection of Signals of Uncertain Frequency", J. Acoust. Soc. Am. 32, 805, (1960). 6. J.P

Effects of Different Spectral Shapes and Amplitude Modulation of Broadband Noise on Annoyance Reactions in a Controlled Listening Experiment.

PubMed

Schäffer, Beat; Pieren, Reto; Schlittmeier, Sabine J; Brink, Mark

2018-05-19

Environmental noise from transportation or industrial infrastructure typically has a broad frequency range. Different sources may have disparate acoustical characteristics, which may in turn affect noise annoyance. However, knowledge of the relative contribution of the different acoustical characteristics of broadband noise to annoyance is still scarce. In this study, the subjectively perceived short-term (acute) annoyance reactions to different broadband sounds (namely, realistic outdoor wind turbine and artificial, generic sounds) at 40 dBA were investigated in a controlled laboratory listening experiment. Combined with the factorial design of the experiment, the sounds allowed for separation of the effects of three acoustical characteristics on annoyance, namely, spectral shape, depth of periodic amplitude modulation (AM), and occurrence (or absence) of random AM. Fifty-two participants rated their annoyance with the sounds. Annoyance increased with increasing energy content in the low-frequency range as well as with depth of periodic AM, and was higher in situations with random AM than without. Similar annoyance changes would be evoked by sound pressure level changes of up to 8 dB. The results suggest that besides standard sound pressure level metrics, other acoustical characteristics of (broadband) noise should also be considered in environmental impact assessments, e.g., in the context of wind turbine installations.

Printability of alloys for additive manufacturing

PubMed Central

Mukherjee, T.; Zuback, J. S.; De, A.; DebRoy, T.

2016-01-01

Although additive manufacturing (AM), or three dimensional (3D) printing, provides significant advantages over existing manufacturing techniques, metallic parts produced by AM are susceptible to distortion, lack of fusion defects and compositional changes. Here we show that the printability, or the ability of an alloy to avoid these defects, can be examined by developing and testing appropriate theories. A theoretical scaling analysis is used to test vulnerability of various alloys to thermal distortion. A theoretical kinetic model is used to examine predisposition of different alloys to AM induced compositional changes. A well-tested numerical heat transfer and fluid flow model is used to compare susceptibilities of various alloys to lack of fusion defects. These results are tested and validated with independent experimental data. The findings presented in this paper are aimed at achieving distortion free, compositionally sound and well bonded metallic parts. PMID:26796864

Surface-specific additive manufacturing test artefacts

NASA Astrophysics Data System (ADS)

Townsend, Andrew; Racasan, Radu; Blunt, Liam

2018-06-01

Many test artefact designs have been proposed for use with additive manufacturing (AM) systems. These test artefacts have primarily been designed for the evaluation of AM form and dimensional performance. A series of surface-specific measurement test artefacts designed for use in the verification of AM manufacturing processes are proposed here. Surface-specific test artefacts can be made more compact because they do not require the large dimensions needed for accurate dimensional and form measurements. The series of three test artefacts are designed to provide comprehensive information pertaining to the manufactured surface. Measurement possibilities include deviation analysis, surface texture parameter data generation, sub-surface analysis, layer step analysis and build resolution comparison. The test artefacts are designed to provide easy access for measurement using conventional surface measurement techniques, for example, focus variation microscopy, stylus profilometry, confocal microscopy and scanning electron microscopy. Additionally, the test artefacts may be simply visually inspected as a comparative tool, giving a fast indication of process variation between builds. The three test artefacts are small enough to be included in every build and include built-in manufacturing traceability information, making them a convenient physical record of the build.

L1 track trigger for the CMS HL-LHC upgrade using AM chips and FPGAs

NASA Astrophysics Data System (ADS)

Fedi, Giacomo

2017-08-01

The increase of luminosity at the HL-LHC will require the introduction of tracker information in CMS's Level-1 trigger system to maintain an acceptable trigger rate when selecting interesting events, despite the order of magnitude increase in minimum bias interactions. To meet the latency requirements, dedicated hardware has to be used. This paper presents the results of tests of a prototype system (pattern recognition ezzanine) as core of pattern recognition and track fitting for the CMS experiment, combining the power of both associative memory custom ASICs and modern Field Programmable Gate Array (FPGA) devices. The mezzanine uses the latest available associative memory devices (AM06) and the most modern Xilinx Ultrascale FPGAs. The results of the test for a complete tower comprising about 0.5 million patterns is presented, using as simulated input events traversing the upgraded CMS detector. The paper shows the performance of the pattern matching, track finding and track fitting, along with the latency and processing time needed. The pT resolution over pT of the muons measured using the reconstruction algorithm is at the order of 1% in the range 3-100 GeV/c.

Soil nutritional status, not inoculum identity, primarily determines the effect of arbuscular mycorrhizal fungi on the growth of Knautia arvensis plants.

PubMed

Doubková, Pavla; Kohout, Petr; Sudová, Radka

2013-10-01

Arbuscular mycorrhizal (AM) symbiosis is among the factors contributing to plant survival in serpentine soils characterised by unfavourable physicochemical properties. However, AM fungi show a considerable functional diversity, which is further modified by host plant identity and edaphic conditions. To determine the variability among serpentine AM fungal isolates in their effects on plant growth and nutrition, a greenhouse experiment was conducted involving two serpentine and two non-serpentine populations of Knautia arvensis plants grown in their native substrates. The plants were inoculated with one of the four serpentine AM fungal isolates or with a complex AM fungal community native to the respective plant population. At harvest after 6-month cultivation, intraradical fungal development was assessed, AM fungal taxa established from native fungal communities were determined and plant growth and element uptake evaluated. AM symbiosis significantly improved the performance of all the K. arvensis populations. The extent of mycorrhizal growth promotion was mainly governed by nutritional status of the substrate, while the effect of AM fungal identity was negligible. Inoculation with the native AM fungal communities was not more efficient than inoculation with single AM fungal isolates in any plant population. Contrary to the growth effects, a certain variation among AM fungal isolates was revealed in terms of their effects on plant nutrient uptake, especially P, Mg and Ca, with none of the AM fungi being generally superior in this respect. Regardless of AM symbiosis, K. arvensis populations significantly differed in their relative nutrient accumulation ratios, clearly showing the plant's ability to adapt to nutrient deficiency/excess.

Auditory steady-state responses to MM and exponential envelope AM(2)/FM stimuli in normal-hearing adults.

PubMed

D'haenens, Wendy; Dhooge, Ingeborg; De Vel, Eddy; Maes, Leen; Bockstael, Annelies; Vinck, Bart M

2007-08-01

The present study utilized a commercially available multiple auditory steady-state response (ASSR) system to test normal hearing adults (n=55). The primary objective was to evaluate the impact of the mixed modulation (MM) and the novel proposed exponential AM(2)/FM stimuli on the signal-to-noise ratio (SNR) and threshold estimation accuracy, through a within-subject comparison. The second aim was to establish a normative database for both stimulus types. The results demonstrated that the AM(2)/FM and MM stimulus had a similar effect on the SNR, whereas the ASSR threshold results revealed that the AM(2)/FM produced better thresholds than the MM stimulus for the 500, 1000, and 4000 Hz carrier frequency. The mean difference scores to tones of 500, 1000, 2000, and 4000 Hz were for the MM stimulus: 20+/-12, 14+/-9, 10+/-8, and 12+/-8 dB; and for the AM(2)/FM stimulus: 18+/-13, 12+/-8, 11+/-8, and 10+/-8 dB, respectively. The current research confirms that the AM(2)/FM stimulus can be used efficiently to test normal hearing adults.

Crossability of Triticum urartu and Triticum monococcum Wheats, Homoeologous Recombination, and Description of a Panel of Interspecific Introgression Lines

PubMed Central

Fricano, Agostino; Brandolini, Andrea; Rossini, Laura; Sourdille, Pierre; Wunder, Joerg; Effgen, Sigi; Hidalgo, Alyssa; Erba, Daniela; Piffanelli, Pietro; Salamini, Francesco

2014-01-01

Triticum monococcum (genome Am) and T. urartu (genome Au) are diploid wheats, with the first having been domesticated in the Neolithic Era and the second being a wild species. In a germplasm collection, rare wild T. urartu lines with the presence of T. monococcum alleles were found. This stimulated our interest to develop interspecific introgression lines of T. urartu in T. monococcum, a breeding tool currently implemented in several crop species. Moreover, the experiments reported were designed to reveal the existence in nature of Am/Au intermediate forms and to clarify whether the two species are at least marginally sexually compatible. From hand-made interspecific crosses, almost-sterile F1 plants were obtained when the seed-bearing parent was T. monococcum. A high degree of fertility was, however, evident in some advanced generations, particularly when T. urartu donors were molecularly more related to T. monococcum. Analysis of the marker populations demonstrated chromosome pairing and recombination in F1 hybrid plants. Forty-six introgression lines were developed using a line of T. monococcum with several positive agronomic traits as a recurrent parent. Microsatellite markers were tested on Au and Am genomes, ordered in a T. monococcum molecular map, and used to characterize the exotic DNA fragments present in each introgression line. In a test based on 28 interspecific introgression lines, the existence of genetic variation associated with T. urartu chromosome fragments was proven for the seed content of carotenoids, lutein, β-cryptoxanthin, and zinc. The molecular state of available introgression lines is summarized. PMID:25147190

Early Rockets

NASA Image and Video Library

1959-05-18

A squirrel monkey, Able, is being ready for placement into a capsule for a preflight test of Jupiter, AM-18 mission. AM-18 was launched on May 28, 1959 and also carried a rhesus monkey, Baker, into suborbit.

A Comparison of Pig Farmers' and Veterinarians' Perceptions and Intentions to Reduce Antimicrobial Usage in Six European Countries.

PubMed

Visschers, V H M; Backhans, A; Collineau, L; Loesken, S; Nielsen, E O; Postma, M; Belloc, C; Dewulf, J; Emanuelson, U; Grosse Beilage, E; Siegrist, M; Sjölund, M; Stärk, K D C

2016-11-01

Antimicrobial (AM) resistance is an increasing problem in human and veterinary medicine. To manage this problem, the usage of AM should be reduced in pig farming, as well as in other areas. It is important to investigate the factors that influence both pig farmers' and veterinarians' intentions to reduce AM usage, which is a prerequisite for developing intervention measures. We conducted a mail survey among pig farmers (N = 1,294) and an online survey among veterinarians (N = 334) in Belgium, Denmark, France, Germany, Sweden and Switzerland. The farmers' survey assessed the perceived risks and benefits of and need for AM usage; the intention to reduce AM usage; farmers' efficacy (i.e. perception of their ability to reduce AM usage); support from their veterinarian; and the future reduction potential of AM usage. Additionally, self-reported reduction behaviours, the perceived farmers' barriers to reduce AM usage and relationships with farmers were assessed in the veterinarians' survey. The results showed that farmers and veterinarians had similar perceptions of the risks and benefits of AM usage. Veterinarians appeared to be more optimistic than pig farmers about reducing AM usage in pig farming. Farmers believed that their efficacy over AM reduction was relatively high. Farmers' intention to reduce AM usage and veterinarians' self-reported reduction behaviours were mainly associated with factors concerning the feasibility of reducing AM usage. To promote prudent AM usage, pig farmers should learn and experience how to reduce usage by applying alternative measures, whereas veterinarians should strengthen their advisory role and competencies to support and educate farmers. © 2016 Blackwell Verlag GmbH.

E-cigarette aerosol exposure can cause craniofacial defects in Xenopus laevis embryos and mammalian neural crest cells

PubMed Central

Kennedy, Allyson E.; Kandalam, Suraj; Olivares-Navarrete, Rene

2017-01-01

Since electronic cigarette (ECIG) introduction to American markets in 2007, vaping has surged in popularity. Many, including women of reproductive age, also believe that ECIG use is safer than traditional tobacco cigarettes and is not hazardous when pregnant. However, there are few studies investigating the effects of ECIG exposure on the developing embryo and nothing is known about potential effects on craniofacial development. Therefore, we have tested the effects of several aerosolized e-cigarette liquids (e-cigAM) in an in vivo craniofacial model, Xenopus laevis, as well as a mammalian neural crest cell line. Results demonstrate that e-cigAM exposure during embryonic development induces a variety of defects, including median facial clefts and midface hypoplasia in two of e-cigAMs tested e-cigAMs. Detailed quantitative analyses of the facial morphology revealed that nicotine is not the main factor in inducing craniofacial defects, but can exacerbate the effects of the other e-liquid components. Additionally, while two different e-cigAMs can have very similar consequences on facial appearances, there are subtle differences that could be due to the differences in e-cigAM components. Further assessment of embryos exposed to these particular e-cigAMs revealed cranial cartilage and muscle defects and a reduction in the blood supply to the face. Finally, the expression of markers for vascular and cartilage differentiation was reduced in a mammalian neural crest cell line corroborating the in vivo effects. Our work is the first to show that ECIG use could pose a potential hazard to the developing embryo and cause craniofacial birth defects. This emphasizes the need for more testing and regulation of this new popular product. PMID:28957438

E-cigarette aerosol exposure can cause craniofacial defects in Xenopus laevis embryos and mammalian neural crest cells.

PubMed

Kennedy, Allyson E; Kandalam, Suraj; Olivares-Navarrete, Rene; Dickinson, Amanda J G

2017-01-01

Since electronic cigarette (ECIG) introduction to American markets in 2007, vaping has surged in popularity. Many, including women of reproductive age, also believe that ECIG use is safer than traditional tobacco cigarettes and is not hazardous when pregnant. However, there are few studies investigating the effects of ECIG exposure on the developing embryo and nothing is known about potential effects on craniofacial development. Therefore, we have tested the effects of several aerosolized e-cigarette liquids (e-cigAM) in an in vivo craniofacial model, Xenopus laevis, as well as a mammalian neural crest cell line. Results demonstrate that e-cigAM exposure during embryonic development induces a variety of defects, including median facial clefts and midface hypoplasia in two of e-cigAMs tested e-cigAMs. Detailed quantitative analyses of the facial morphology revealed that nicotine is not the main factor in inducing craniofacial defects, but can exacerbate the effects of the other e-liquid components. Additionally, while two different e-cigAMs can have very similar consequences on facial appearances, there are subtle differences that could be due to the differences in e-cigAM components. Further assessment of embryos exposed to these particular e-cigAMs revealed cranial cartilage and muscle defects and a reduction in the blood supply to the face. Finally, the expression of markers for vascular and cartilage differentiation was reduced in a mammalian neural crest cell line corroborating the in vivo effects. Our work is the first to show that ECIG use could pose a potential hazard to the developing embryo and cause craniofacial birth defects. This emphasizes the need for more testing and regulation of this new popular product.

Distinct contributions of the fornix and inferior longitudinal fasciculus to episodic and semantic autobiographical memory.

PubMed

Hodgetts, Carl J; Postans, Mark; Warne, Naomi; Varnava, Alice; Lawrence, Andrew D; Graham, Kim S

2017-09-01

Autobiographical memory (AM) is multifaceted, incorporating the vivid retrieval of contextual detail (episodic AM), together with semantic knowledge that infuses meaning and coherence into past events (semantic AM). While neuropsychological evidence highlights a role for the hippocampus and anterior temporal lobe (ATL) in episodic and semantic AM, respectively, it is unclear whether these constitute dissociable large-scale AM networks. We used high angular resolution diffusion-weighted imaging and constrained spherical deconvolution-based tractography to assess white matter microstructure in 27 healthy young adult participants who were asked to recall past experiences using word cues. Inter-individual variation in the microstructure of the fornix (the main hippocampal input/output pathway) related to the amount of episodic, but not semantic, detail in AMs - independent of memory age. Conversely, microstructure of the inferior longitudinal fasciculus, linking occipitotemporal regions with ATL, correlated with semantic, but not episodic, AMs. Further, these significant correlations remained when controlling for hippocampal and ATL grey matter volume, respectively. This striking correlational double dissociation supports the view that distinct, large-scale distributed brain circuits underpin context and concepts in AM. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cotton, T. E. Anne; Fitter, Alastair H.; Miller, R. Michael

Understanding the natural dynamics of arbuscular mycorrhizal (AM) fungi and their response to global environmental change is essential for the prediction of future plant growth and ecosystem functions. We investigated the long-term temporal dynamics and effect of elevated atmospheric carbon dioxide (CO 2) and ozone (O 3) concentrations on AM fungal communities. Molecular methods were used to characterize the AM fungal communities of soybean ( Glycine max) grown under elevated and ambient atmospheric concentrations of both CO 2 and O 3 within a free air concentration enrichment experiment in three growing seasons over 5 yr. Elevated CO 2 altered themore » community composition of AM fungi, increasing the ratio of Glomeraceae to Gigasporaceae. By contrast, no effect of elevated O 3 on AM fungal communities was detected. However, the greatest compositional differences detected were between years, suggesting that, at least in the short term, large-scale interannual temporal dynamics are stronger mediators than atmospheric CO 2 concentrations of AM fungal communities. We conclude that, although atmospheric change may significantly alter AM fungal communities, this effect may be masked by the influences of natural changes and successional patterns through time. We suggest that changes in carbon availability are important determinants of the community dynamics of AM fungi.« less

Characterization of a mine fire using atmospheric monitoring system sensor data

PubMed Central

Yuan, L.; Thomas, R.A.; Zhou, L.

2017-01-01

Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the United States for the detection of fire in the belt entry and the monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data have the potential to provide fire characteristic information such as fire growth — in terms of heat release rate — and exact fire location. Such information is critical in making decisions regarding fire-fighting strategies, underground personnel evacuation and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide concentration, carbon dioxide concentration and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division’s Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy. PMID:28845058

Dispersal of arbuscular mycorrhizal fungi and plants during succession

NASA Astrophysics Data System (ADS)

García de León, David; Moora, Mari; Öpik, Maarja; Jairus, Teele; Neuenkamp, Lena; Vasar, Martti; Bueno, C. Guillermo; Gerz, Maret; Davison, John; Zobel, Martin

2016-11-01

Arbuscular mycorrhizal (AM) fungi are important root symbionts that enhance plant nutrient uptake and tolerance to pathogens and drought. While the role of plant dispersal in shaping successional vegetation is well studied, there is very little information about the dispersal abilities of AM fungi. We conducted a trap-box experiment in a recently abandoned quarry at 10 different distances from the quarry edge (i.e. the potential propagule source) over eleven months to assess the short term, within-year, arrival of plant and AM fungal assemblages and hence their dispersal abilities. Using DNA based techniques we identified AM fungal taxa and analyzed their phylogenetic diversity. Plant diversity was determined by transporting trap soil to a greenhouse and identifying emerging seedlings. We recorded 30 AM fungal taxa. These contained a high proportion of ruderal AM fungi (30% of taxa, 79% of sequences) but the richness and abundance of AM fungi were not related to the distance from the presumed propagule source. The number of sequences of AM fungi decreased over time. Twenty seven plant species (30% of them ruderal) were recorded from the soil seed traps. Plant diversity decreased with distance from the propagule source and increased over time. Our data show that AM fungi with ruderal traits can be fast colonizers of early successional habitats.

Autobiographical memory dysfunctions in depressive disorders.

PubMed

Talarowska, Monika; Berk, Michael; Maes, Michael; Gałecki, Piotr

2016-02-01

Autobiographical memory (AM) is a ubiquitous human experience that belongs to long-term declarative memory. It plays interpersonal and intrapsychic functions. The main aim of this study is to present results of contemporary research on AM in recurrent depressive disorders. The available research literature suggests that AM dysfunctions are a precursor and risk factor for recurrent depressive disorders and that they also appear to be a consequence of depressive symptoms in a bidirectional and interacting manner. These data suggest that AM might be a viable therapeutic target for cognitive remediation strategies, given the impact of cognition on diverse clinical outcomes. © 2015 The Authors. Psychiatry and Clinical Neurosciences © 2015 Japanese Society of Psychiatry and Neurology.

Immediate hypersensitivity reaction following liposomal amphotericin-B (AmBisome) infusion.

PubMed

Nath, Proggananda; Basher, Ariful; Harada, Michiyo; Sarkar, Santana; Selim, Shahjada; Maude, Richard J; Noiri, Eisei; Faiz, Abul

2014-10-01

Liposomal amphotericin-B (AmBisome) is now becoming first choice for the treatment of visceral leishmaniasis (kala-azar) patients due to high efficacy and less toxicity. The reported incidence of hypersensitivity reactions to liposomal amphotericin-B (AmBisome), especially during therapy, is very rare. We report two patients with kala-azar: one developed breathing difficulties and hypotension followed by shock and the other had facial angioedema with chest tightness during treatment. Both patients were managed with immediate action of injection: adrenaline, diphenhydramine and hydrocortisone. In our experience, AmBisome can cause severe hypersensitivity reactions that warrant proper support and close supervision. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

An arbuscular mycorrhizal fungus and Epichloë festucae var. lolii reduce Bipolaris sorokiniana disease incidence and improve perennial ryegrass growth.

PubMed

Li, Fang; Guo, Yan'e; Christensen, Michael J; Gao, Ping; Li, Yanzhong; Duan, Tingyu

2018-02-01

Leaf spot of perennial ryegrass (Lolium perenne) caused by Bipolaris sorokiniana is an important disease in temperate regions of the world. We designed this experiment to test for the combined effects of the arbuscular mycorrhizal (AM) fungus Claroideoglomus etunicatum and the grass endophyte fungus Epichloë festucae var. lolii on growth and disease occurrence in perennial ryegrass. The results show that C. etunicatum increased plant P uptake and total dry weight and that this beneficial effect was slightly enhanced when in association with the grass endophyte. The presence in plants of both the endophyte and B. sorokiniana decreased AM fungal colonization. Plants inoculated with B. sorokiniana showed the typical leaf spot symptoms 2 weeks after inoculation and the lowest disease incidence was with plants that were host to both C. etunicatum and E. festucae var. lolii. Plants with these two fungi had much higher activity of peroxidases (POD), superoxide dismutase (SOD) and catalase (CAT) and lower values of malondialdehyde (MDA) and hydrogen peroxide (H 2 O 2 ). The AM fungus C. etunicatum and the grass endophyte fungus E. festucae var. lolii have the potential to promote perennial ryegrass growth and resistance to B. sorokiniana leaf spot.

Suppression of the root-knot nematode [Meloidogyne incognita (Kofoid & White) Chitwood] on tomato by dual inoculation with arbuscular mycorrhizal fungi and plant growth-promoting rhizobacteria.

PubMed

Liu, Runjin; Dai, Mei; Wu, Xia; Li, Min; Liu, Xingzhong

2012-05-01

Arbuscular mycorrhizal (AM) fungi and plant growth-promoting rhizobacteria (PGPR) have potential for the biocontrol of soil-borne diseases. The objectives of this study were to quantify the interactions between AM fungi [Glomus versiforme (Karsten) Berch and Glomus mosseae (Nicol. & Gerd.) Gerdemann & Trappe] and PGPR [Bacillus polymyxa (Prazmowski) Mace and Bacillus sp.] during colonization of roots and rhizosphere of tomato (Lycopersicon esculentum Mill) plants (cultivar Jinguan), and to determine their combined effects on the root-knot nematode, Meloidogyne incognita, and on tomato growth. Three greenhouse experiments were conducted. PGPR increased colonization of roots by AM fungi, and AM fungi increased numbers of PGPR in the rhizosphere. Dual inoculations of AM fungi plus PGPR provided greater control of M. incognita and greater promotion of plant growth than single inoculations, and the best combination was G. mosseae plus Bacillus sp. The results indicate that specific AM fungi and PGPR can stimulate each other and that specific combinations of AM fungi and PGPR can interact to suppress M. incognita and disease development. © Springer-Verlag 2012

Evolutionary asymmetry in the arbuscular mycorrhizal symbiosis: conservatism in fungal morphology does not predict host plant growth.

PubMed

Koch, Alexander M; Antunes, Pedro M; Maherali, Hafiz; Hart, Miranda M; Klironomos, John N

2017-05-01

Although arbuscular mycorrhizal (AM) fungi are obligate symbionts that can influence plant growth, the magnitude and direction of these effects are highly variable within fungal genera and even among isolates within species, as well as among plant taxa. To determine whether variability in AM fungal morphology and growth is correlated with AM fungal effects on plant growth, we established a common garden experiment with 56 AM fungal isolates comprising 17 genera and six families growing with three plant host species. Arbuscular mycorrhizal fungal morphology and growth was highly conserved among isolates of the same species and among species within a family. By contrast, plant growth response to fungal inoculation was highly variable, with the majority of variation occurring among different isolates of the same AM fungal species. Our findings show that host performance cannot be predicted from AM fungal morphology and growth traits. Divergent effects on plant growth among isolates within an AM fungal species may be caused by coevolution between co-occurring fungal and plant populations. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

The Improvement of Bone-Tendon Fixation by Porous Titanium Interference Screw: A Rabbit Animal Model.

PubMed

Tsai, Pei-I; Chen, Chih-Yu; Huang, Shu-Wei; Yang, Kuo-Yi; Lin, Tzu-Hung; Chen, San-Yuan; Sun, Jui-Sheng

2018-05-04

The interference screw is a widely used fixation device in the anterior cruciate ligament (ACL) reconstruction surgeries. Despite the generally satisfactory results, problems of using interference screws were reported. By using additive manufacturing (AM) technology, we developed an innovative titanium alloy (Ti 6 Al 4 V) interference screw with rough surface and inter-connected porous structure designs to improve the bone-tendon fixation. An innovative Ti 6 Al 4 V interference screws were manufactured by AM technology. In vitro mechanical tests were performed to validate its mechanical properties. Twenty-seven New Zealand white rabbits were randomly divided into control and AM screw groups for biomechanical analyses and histological analysis at 4, 8 and 12 weeks postoperatively; while micro-CT analysis was performed at 12 weeks postoperatively. The biomechanical tests showed that the ultimate failure load in the AM interference screw group was significantly higher than that in the control group at all tested periods. These results were also compatible with the findings of micro-CT and histological analyses. In micro-CT analysis, the bone-screw gap was larger in the control group; while for the additive manufactured screw, the screw and bone growth was in close contact. In histological study, the bone-screw gaps were wider in the control group and were almost invisible in the AM screw group. The innovative AM interference screws with surface roughness and inter-connected porous architectures demonstrated better bone-tendon-implant integration, and resulted in stronger biomechanical characteristics when compared to traditional screws. These advantages can be transferred to future interference screw designs to improve their clinical performance. The AM interference screw could improve graft fixation and eventually result in better biomechanical performance of the bone-tendon-screw construct. The innovative AM interference screws can be transferred to future interference screw designs to improve the performance of implants. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

STS-107 Pilot William McCool during TCDT M113 training activities

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- -- STS-107 Pilot William 'Willie' McCool takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

STS-107 Pilot William McCool during TCDT M113 training activities

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- -- STS-107 Pilot William 'Willie' McCool operates an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. Instructor George Hoggard (left) supervises the training. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

STS-107 M.S. Laurel Clark during TCDT M113 training activities

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Mission Specialist Laurel Clark (in yellow cap) is instructed on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

STS-107 M.S. Laurel Clark takes a break during TCDT M113 training

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Mission Specialist Laurel Clark takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

STS-107 M.S. Kalpana Chawla takes a break during TCDT M113 training

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Mission Specialist Kalpana Chawla takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

STS-107 Payload Commander Michael Anderson during TCDT M113 training activities

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- -- STS-107 Payload Commander Michael Anderson takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

STS-107 Mission Specialist David Brown during TCDT M113 training activities

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- -- STS-107 Mission Specialist David Brown takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

KSC-02pd1932

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- STS-107 Commander Rick Husband takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. Instructor George Hoggard looks on over Husband's shoulder. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

Installation Restoration Program Records Search for McChord Air Force Base, Washington.

DTIC Science & Technology

1982-08-01

responsible for smoke testing for possi- ble outlets. g ŕ 115 0 V -j q * REFERENCES * .4 g SI * I w I WI j EU REFERENCES Brandin , R. M., and S. Sgt. S. A...Ms. R. Brandin . Griffin, W. C., et al. 1962. Water Resources of the Tacoma Area Washington. Geological Survey Water Supply Paper 1499-B. Prepared in...MEMBERS vS U STEVEN R. HOFFMAN Education B.S., Civil Engineering, South Dakota School of Mines and Technology, 1971 Experience - -. Mr. Hoffman is a

Risk factors for occupational acute mountain sickness.

PubMed

Vinnikov, D; Brimkulov, N; Krasotski, V; Redding-Jones, R; Blanc, P D

2014-10-01

Studies of occupational acute mountain sickness (AMS) have not focused on the more severe end of the spectrum to date. To examine risk factors associated with the development of occupational AMS severe enough to receive treatment in a compression chamber. A nested case referent study in a cohort of high-altitude (4000 m) mine workers, comparing cases of severe, chamber-treated AMS to matched referents. Using logistic regression, we tested potential risk factors based on premorbid surveillance examinations, including cigarette smoking (current smoking, smoking intensity and exhaled carbon monoxide [CO]). There were 15 cases and 30 controls. In multivariate analysis including age, sex and place of residence, current smoking was associated with increased risk of severe AMS (odds ratio [OR] 10.0; 95% confidence interval [CI] 1.5-67.4), taking into account any prior, less severe AMS event, which was also a potent risk factor (OR 33.3; 95% CI 2.8-390). Smoking intensity (cigarettes per day) and exhaled CO were also statistically significantly associated with severe AMS. Cigarette smoking is a strong, previously under-appreciated risk factor for severe AMS. Because this is a modifiable factor, these findings suggest that workplace-based smoking cessation should be tested as an intervention to prevent such morbidity. © The Author 2014. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Autobiographical Memory Deficits in Alcohol-Dependent Patients with Short- and Long-Term Abstinence.

PubMed

Nandrino, Jean-Louis; El Haj, Mohamad; Torre, Julie; Naye, Delphine; Douchet, Helyette; Danel, Thierry; Cottençin, Oliver

2016-04-01

Autobiographical memory (AM) enables the storage and retrieval of life experiences that allow individuals to build their sense of identity. Several AM impairments have been described in patients with alcohol abuse disorders without assessing whether such deficits can be recovered. This cross-sectional study aimed to identify whether the semantic (SAM) and episodic (EAM) dimensions of AM are affected in individuals with alcohol dependence after short-term abstinence (STA) or long-term abstinence (LTA). A second aim of this study was to examine the factors that could disrupt the efficiency of semantic and episodic AM (the impact of depression severity, cognitive functions, recent or early traumatic events, and drinking history variables). After clinical and cognitive evaluations (alcohol consumption, depression, anxiety, IQ, memory performance), AM was assessed with the Autobiographical Memory Interview in patients with recent (between 4 and 6 weeks) and longer (at least 6 months) abstinence. Participants were asked to retrieve the number and nature of traumatic or painful life experiences in recent or early life periods (using the Childhood Traumatic Events Scale). The 2 abstinent groups had lower global EAM and SAM scores than the control group. These scores were comparable for both abstinent groups. For childhood events, no significant differences were observed in SAM for both groups compared with control participants. For early adulthood and recent events, both STA and LTA groups had lower scores on both SAM and EAM. Moreover, there was a negative correlation between the length of substance consumption and SAM scores. This study highlighted a specific AM disorder in both episodic and semantic dimensions. These deficits remained after 6 months of abstinence. This AM impairment may be explained by compromised encoding and consolidation of memories during bouts of drinking. Copyright © 2016 by the Research Society on Alcoholism.

Synthetic Ligands of Cannabinoid Receptors Affect Dauer Formation in the Nematode Caenorhabditis elegans.

PubMed

Reis Rodrigues, Pedro; Kaul, Tiffany K; Ho, Jo-Hao; Lucanic, Mark; Burkewitz, Kristopher; Mair, William B; Held, Jason M; Bohn, Laura M; Gill, Matthew S

2016-06-01

Under adverse environmental conditions the nematode Caenorhabditis elegans can enter an alternate developmental stage called the dauer larva. To identify lipophilic signaling molecules that influence this process, we screened a library of bioactive lipids and found that AM251, an antagonist of the human cannabinoid (CB) receptor, suppresses dauer entry in daf-2 insulin receptor mutants. AM251 acted synergistically with glucose supplementation indicating that the metabolic status of the animal influenced the activity of this compound. Similarly, loss of function mutations in the energy-sensing AMP-activated kinase subunit, aak-2, enhanced the dauer-suppressing effects of AM251, while constitutive activation of aak-2 in neurons was sufficient to inhibit AM251 activity. Chemical epistasis experiments indicated that AM251 acts via G-protein signaling and requires the TGF-β ligand DAF-7, the insulin peptides DAF-28 and INS-6, and a functional ASI neuron to promote reproductive growth. AM251 also required the presence of the SER-5 serotonin receptor, but in vitro experiments suggest that this may not be via a direct interaction. Interestingly, we found that other antagonists of mammalian CB receptors also suppress dauer entry, while the nonselective CB receptor agonist, O-2545, not only inhibited the activity of AM251, but also was able to promote dauer entry when administered alone. Since worms do not have obvious orthologs of CB receptors, the effects of synthetic CBs on neuroendocrine signaling in C. elegans are likely to be mediated via another, as yet unknown, receptor mechanism. However, we cannot exclude the existence of a noncanonical CB receptor in C. elegans. Copyright © 2016 Rodrigues et al.

Synthetic Ligands of Cannabinoid Receptors Affect Dauer Formation in the Nematode Caenorhabditis elegans

PubMed Central

Reis Rodrigues, Pedro; Kaul, Tiffany K.; Ho, Jo-Hao; Lucanic, Mark; Burkewitz, Kristopher; Mair, William B.; Held, Jason M.; Bohn, Laura M.; Gill, Matthew S.

2016-01-01

Under adverse environmental conditions the nematode Caenorhabditis elegans can enter an alternate developmental stage called the dauer larva. To identify lipophilic signaling molecules that influence this process, we screened a library of bioactive lipids and found that AM251, an antagonist of the human cannabinoid (CB) receptor, suppresses dauer entry in daf-2 insulin receptor mutants. AM251 acted synergistically with glucose supplementation indicating that the metabolic status of the animal influenced the activity of this compound. Similarly, loss of function mutations in the energy-sensing AMP-activated kinase subunit, aak-2, enhanced the dauer-suppressing effects of AM251, while constitutive activation of aak-2 in neurons was sufficient to inhibit AM251 activity. Chemical epistasis experiments indicated that AM251 acts via G-protein signaling and requires the TGF-β ligand DAF-7, the insulin peptides DAF-28 and INS-6, and a functional ASI neuron to promote reproductive growth. AM251 also required the presence of the SER-5 serotonin receptor, but in vitro experiments suggest that this may not be via a direct interaction. Interestingly, we found that other antagonists of mammalian CB receptors also suppress dauer entry, while the nonselective CB receptor agonist, O-2545, not only inhibited the activity of AM251, but also was able to promote dauer entry when administered alone. Since worms do not have obvious orthologs of CB receptors, the effects of synthetic CBs on neuroendocrine signaling in C. elegans are likely to be mediated via another, as yet unknown, receptor mechanism. However, we cannot exclude the existence of a noncanonical CB receptor in C. elegans. PMID:27172180

76 FR 69678 - Domestic Dates Produced or Packed in Riverside County, CA; Proposed Amendments to Marketing Order...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-09

... an alternate during that time. AMS's experience with similar marketing programs is that establishing... DEPARTMENT OF AGRICULTURE Agricultural Marketing Service 7 CFR Part 987 [Doc. No. AMS-FV-10-0025... Marketing Order 987 and Referendum Order AGENCY: Agricultural Marketing Service, USDA. ACTION: Proposed rule...

Progress on multi-nuclide AMS of JAEA-AMS-TONO

NASA Astrophysics Data System (ADS)

Saito-Kokubu, Yoko; Matsubara, Akihiro; Miyake, Masayasu; Nishizawa, Akimitsu; Ohwaki, Yoshio; Nishio, Tomohiro; Sanada, Katsuki; Hanaki, Tatsumi

2015-10-01

The JAEA-AMS-TONO (Japan Atomic Energy Agency's Accelerator Mass Spectrometer established at the Tono Geoscience Center) facility has been used for the dating of geological samples. The AMS system is versatile, based on a 5 MV tandem Pelletron-type accelerator. Since its establishment in 1997, the AMS system has been used for measurement of carbon-14 (14C) mainly for 14C dating studies in neotectonics and hydrogeology, in support of JAEA's research on geosphere stability applicable to the long-term isolation of high-level radioactive waste. Results of the measurement of 14C in soils and plants has been applied to the dating of fault activity and volcanism. Development of beryllium-10 (10Be) and aluminum-26 (26Al) AMS systems are now underway to enhance the capability of the multi-nuclide AMS in studies of dating by cosmogenic nuclides. The 10Be-AMS system has already been used for routine measurements in applied studies and improvements of the measurement technique have been made. Now we plan to fine tune the system and perform test measurements to develop the 26Al-AMS system.

Risk Assessment of Physiological Effects of Atmospheric Composition and Pressure in Constellation Vehicles

NASA Technical Reports Server (NTRS)

Scheuring, Richard A.; Conkin, Johnny; Jones, J. A.; Gernhardt, M.

2007-01-01

To limit the risk of fire and reduce denitrogenation time to prevent decompression sickness to support frequent extravehicular activities on the Moon, a hypobaric (PB = 414 mmHg) and mildly hypoxic (ppO2 = 132 mmHg, 32% O2 - 68% N2) living environment is considered for the Crew Exploration Vehicle (CEV) and Lunar Surface Access Module (LSAM). With acute change in ppO2 from 145-178 mmHg at standard vehicular operating pressure to less than 125 mmHg at desired lunar surface vehicular operating pressures, there is the possibility that some crewmembers may develop symptoms of Acute Mountain Sickness (AMS). The signs and symptoms of AMS (headache plus nausea, dizziness, fatigue, or sleeplessness), could impact crew health and performance on lunar surface missions. An exhaustive literature review on the topic of the physiological effects of reduced ppO2 and absolute pressure as may contribute to the development of altitude symptoms or AMS was performed. The results of the nine most rigorous studies were collated, analyzed and contents on AMS and hypoxia symptoms summarized. There is evidence for an absolute pressure effect per se on AMS, so the higher the altitude for a given hypoxic alveolar O2 partial pressure (PAO2), the greater the AMS response. About 25% of adults are likely to experience mild AMS near 2,000 m altitude following a rapid ascent from sea level while breathing air (6,500 feet, acute PAO2 = 75 mmHg). The operational experience with the Shuttle staged denitrogenation protocol at 528 mmHg (3,048 m) while breathing 26.5% O2 (acute PAO2 = 85 mmHg) in astronauts adapting to microgravity suggests a similar likely experience in the proposed CEV environment. We believe the risk of mild AMS is greater given a PAO2 of 77 mmHg at 4,876 m altitude while breathing 32% O2 than at 1,828 m altitude while breathing 21% O2. Only susceptible astronauts would develop mild and transient AMS with prolonged exposure to 414 mmHg (4,876 m) while breathing 32% O2 (acute PAO2 = 77 mmHg). So the following may be employed for operational risk reduction: 1) develop procedures to increase PB as needed in the CEV, and use a gradual or staged reduction in cabin pressure during lunar outbound; 2) train crews for symptoms of hypoxia, to allow early recognition and consider pre-adaptation of crews to a hypoxic environment prior to launch, 3) consider prophylactic acetazolamide for acute pressure changes and be prepared to treat any AMS associated symptoms early with both carbonic anhydrase inhibitors and supplemental oxygen.

Anti-Inflammatory Effects of Adult Stem Cells in Sustained Lung Injury: A Comparative Study

PubMed Central

Moodley, Yuben; Vaghjiani, Vijesh; Chan, James; Baltic, Svetlana; Ryan, Marisa; Tchongue, Jorge; Samuel, Chrishan S.; Murthi, Padma; Parolini, Ornella; Manuelpillai, Ursula

2013-01-01

Lung diseases are a major cause of global morbidity and mortality that are treated with limited efficacy. Recently stem cell therapies have been shown to effectively treat animal models of lung disease. However, there are limitations to the translation of these cell therapies to clinical disease. Studies have shown that delayed treatment of animal models does not improve outcomes and that the models do not reflect the repeated injury that is present in most lung diseases. We tested the efficacy of amnion mesenchymal stem cells (AM-MSC), bone marrow MSC (BM-MSC) and human amniotic epithelial cells (hAEC) in C57BL/6 mice using a repeat dose bleomycin-induced model of lung injury that better reflects the repeat injury seen in lung diseases. The dual bleomycin dose led to significantly higher levels of inflammation and fibrosis in the mouse lung compared to a single bleomycin dose. Intravenously infused stem cells were present in the lung in similar numbers at days 7 and 21 post cell injection. In addition, stem cell injection resulted in a significant decrease in inflammatory cell infiltrate and a reduction in IL-1 (AM-MSC), IL-6 (AM-MSC, BM-MSC, hAEC) and TNF-α (AM-MSC). The only trophic factor tested that increased following stem cell injection was IL-1RA (AM-MSC). IL-1RA levels may be modulated by GM-CSF produced by AM-MSC. Furthermore, only AM-MSC reduced collagen deposition and increased MMP-9 activity in the lung although there was a reduction of the pro-fibrogenic cytokine TGF-β following BM-MSC, AM-MSC and hAEC treatment. Therefore, AM-MSC may be more effective in reducing injury following delayed injection in the setting of repeated lung injury. PMID:23936322

Reconstruction of early phase deformations by integrated magnetic and mesotectonic data evaluation

NASA Astrophysics Data System (ADS)

Sipos, András A.; Márton, Emő; Fodor, László

2018-02-01

Markers of brittle faulting are widely used for recovering past deformation phases. Rocks often have oriented magnetic fabrics, which can be interpreted as connected to ductile deformation before cementation of the sediment. This paper reports a novel statistical procedure for simultaneous evaluation of AMS (Anisotropy of Magnetic Susceptibility) and fault-slip data. The new method analyzes the AMS data, without linearization techniques, so that weak AMS lineation and rotational AMS can be assessed that are beyond the scope of classical methods. This idea is extended to the evaluation of fault-slip data. While the traditional assumptions of stress inversion are not rejected, the method recovers the stress field via statistical hypothesis testing. In addition it provides statistical information needed for the combined evaluation of the AMS and the mesotectonic (0.1 to 10 m) data. In the combined evaluation a statistical test is carried out that helps to decide if the AMS lineation and the mesotectonic markers (in case of repeated deformation of the oldest set of markers) were formed in the same or different deformation phases. If this condition is met, the combined evaluation can improve the precision of the reconstruction. When the two data sets do not have a common solution for the direction of the extension, the deformational origin of the AMS is questionable. In this case the orientation of the stress field responsible for the AMS lineation might be different from that which caused the brittle deformation. Although most of the examples demonstrate the reconstruction of weak deformations in sediments, the new method is readily applicable to investigate the ductile-brittle transition of any rock formation as long as AMS and fault-slip data are available.

A&M. Hot liquid waste building (TAN616). Interior of evaporator control ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Hot liquid waste building (TAN-616). Interior of evaporator control room. Date: 1962. INEEL negative no. 62-6824 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Effect of arbuscular mycorrhizal (AM) fungi on 137Cs uptake by plants grown on different soils.

PubMed

Vinichuk, M; Mårtensson, A; Ericsson, T; Rosén, K

2013-01-01

The potential use of mycorrhiza as a bioremediation agent for soils contaminated by radiocesium was evaluated in a greenhouse experiment. The uptake of (137)Cs by cucumber, perennial ryegrass, and sunflower after inoculation with a commercial arbuscular mycorrhizal (AM) product in soils contaminated with (137)Cs was investigated, with non-mycorrhizal quinoa included as a "reference" plant. The effect of cucumber and ryegrass inoculation with AM fungi on (137)Cs uptake was inconsistent. The effect of AM fungi was most pronounced in sunflower: both plant biomass and (137)Cs uptake increased on loamy sand and loamy soils. The total (137)Cs activity accumulated within AM host sunflower on loamy sand and loamy soils was 2.4 and 3.2-fold higher than in non-inoculated plants. Although the enhanced uptake of (137)Cs by quinoa plants on loamy soil inoculated by the AM fungi was observed, the infection of the fungi to the plants was not confirmed. Copyright © 2012 Elsevier Ltd. All rights reserved.

Technical basis for the use of a correlated neutron source in the uranium neutron coincidence collar

DOE PAGES

Root, Margaret A.; Menlove, Howard Olsen; Lanza, Richard C.; ...

2017-01-16

Active neutron coincidence systems are commonly used by international inspectorates to verify a material balance across the various stages of the nuclear fuel cycle. The Uranium Neutron Coincidence Collar (UNCL) is one such instrument; it is used to measure the linear density of 235U (g 235U/cm of active length in assembly) in fresh light water reactor fuel in nuclear fuel fabrication facilities. The UNCL and other active neutron interrogation detectors have historically relied on americium lithium ( 241AmLi) sources to induce fission within the sample in question. Californium-252 is under consideration as a possible alternative to the traditional 241AmLi source.more » Finally, this work relied upon a combination of experiments and Monte Carlo simulations to demonstrate the technical basis for the replacement of 241AmLi sources with 252Cf sources by evaluating the statistical uncertainty in the measurements incurred by each source and assessing the penetrability of neutrons from each source for the UNCL.« less

Technical basis for the use of a correlated neutron source in the uranium neutron coincidence collar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Root, Margaret A.; Menlove, Howard Olsen; Lanza, Richard C.

Active neutron coincidence systems are commonly used by international inspectorates to verify a material balance across the various stages of the nuclear fuel cycle. The Uranium Neutron Coincidence Collar (UNCL) is one such instrument; it is used to measure the linear density of 235U (g 235U/cm of active length in assembly) in fresh light water reactor fuel in nuclear fuel fabrication facilities. The UNCL and other active neutron interrogation detectors have historically relied on americium lithium ( 241AmLi) sources to induce fission within the sample in question. Californium-252 is under consideration as a possible alternative to the traditional 241AmLi source.more » Finally, this work relied upon a combination of experiments and Monte Carlo simulations to demonstrate the technical basis for the replacement of 241AmLi sources with 252Cf sources by evaluating the statistical uncertainty in the measurements incurred by each source and assessing the penetrability of neutrons from each source for the UNCL.« less

Printability of alloys for additive manufacturing

DOE PAGES

Mukherjee, T.; Zuback, J. S.; De, A.; ...

2016-01-22

Although additive manufacturing (AM), or three dimensional (3D) printing, provides significant advantages over existing manufacturing techniques, metallic parts produced by AM are susceptible to distortion, lack of fusion defects and compositional changes. Here we show that the printability, or the ability of an alloy to avoid these defects, can be examined by developing and testing appropriate theories. A theoretical scaling analysis is used to test vulnerability of various alloys to thermal distortion. A theoretical kinetic model is used to examine predisposition of different alloys to AM induced compositional changes. A well-tested numerical heat transfer and fluid flow model is usedmore » to compare susceptibilities of various alloys to lack of fusion defects. These results are tested and validated with independent experimental data. Here, the findings presented in this paper are aimed at achieving distortion free, compositionally sound and well bonded metallic parts.« less

Influence of nutrient signals and carbon allocation on the expression of phosphate and nitrogen transporter genes in winter wheat (Triticum aestivum L.) roots colonized by arbuscular mycorrhizal fungi

PubMed Central

Tian, Hui; Yuan, Xiaolei; Duan, Jianfeng; Li, Wenhu; Zhai, Bingnian; Gao, Yajun

2017-01-01

Arbuscular mycorrhizal (AM) colonization of plant roots causes the down-regulation of expression of phosphate (Pi) or nitrogen (N) transporter genes involved in direct nutrient uptake pathways. The mechanism of this effect remains unknown. In the present study, we sought to determine whether the expression of Pi or N transporter genes in roots of winter wheat colonized by AM fungus responded to (1) Pi or N nutrient signals transferred from the AM extra-radical hyphae, or (2) carbon allocation changes in the AM association. A three-compartment culture system, comprising a root compartment (RC), a root and AM hyphae compartment (RHC), and an AM hyphae compartment (HC), was used to test whether the expression of Pi or N transporter genes responded to nutrients (Pi, NH4+ and NO3-) added only to the HC. Different AM inoculation density treatments (roots were inoculated with 0, 20, 50 and 200 g AM inoculum) and light regime treatments (6 hours light and 18 hours light) were established to test the effects of carbon allocation on the expression of Pi or N transporter genes in wheat roots. The expression of two Pi transporter genes (TaPT4 and TaPHT1.2), five nitrate transporter genes (TaNRT1.1, TaNRT1.2, TaNRT2.1, TaNRT2.2, and TaNRT2.3), and an ammonium transporter gene (TaAMT1.2) was quantified using real-time polymerase chain reaction. The expression of TaPT4, TaNRT2.2, and TaAMT1.2 was down-regulated by AM colonization only when roots of host plants received Pi or N nutrient signals. However, the expression of TaPHT1.2, TaNRT2.1, and TaNRT2.3 was down-regulated by AM colonization, regardless of whether there was nutrient transfer from AM hyphae. The expression of TaNRT1.2 was also down-regulated by AM colonization even when there was no nutrient transfer from AM hyphae. The present study showed that an increase in carbon consumption by the AM fungi did not necessarily result in greater down-regulation of expression of Pi or N transporter genes. PMID:28207830

Influence of nutrient signals and carbon allocation on the expression of phosphate and nitrogen transporter genes in winter wheat (Triticum aestivum L.) roots colonized by arbuscular mycorrhizal fungi.

PubMed

Tian, Hui; Yuan, Xiaolei; Duan, Jianfeng; Li, Wenhu; Zhai, Bingnian; Gao, Yajun

2017-01-01

Arbuscular mycorrhizal (AM) colonization of plant roots causes the down-regulation of expression of phosphate (Pi) or nitrogen (N) transporter genes involved in direct nutrient uptake pathways. The mechanism of this effect remains unknown. In the present study, we sought to determine whether the expression of Pi or N transporter genes in roots of winter wheat colonized by AM fungus responded to (1) Pi or N nutrient signals transferred from the AM extra-radical hyphae, or (2) carbon allocation changes in the AM association. A three-compartment culture system, comprising a root compartment (RC), a root and AM hyphae compartment (RHC), and an AM hyphae compartment (HC), was used to test whether the expression of Pi or N transporter genes responded to nutrients (Pi, NH4+ and NO3-) added only to the HC. Different AM inoculation density treatments (roots were inoculated with 0, 20, 50 and 200 g AM inoculum) and light regime treatments (6 hours light and 18 hours light) were established to test the effects of carbon allocation on the expression of Pi or N transporter genes in wheat roots. The expression of two Pi transporter genes (TaPT4 and TaPHT1.2), five nitrate transporter genes (TaNRT1.1, TaNRT1.2, TaNRT2.1, TaNRT2.2, and TaNRT2.3), and an ammonium transporter gene (TaAMT1.2) was quantified using real-time polymerase chain reaction. The expression of TaPT4, TaNRT2.2, and TaAMT1.2 was down-regulated by AM colonization only when roots of host plants received Pi or N nutrient signals. However, the expression of TaPHT1.2, TaNRT2.1, and TaNRT2.3 was down-regulated by AM colonization, regardless of whether there was nutrient transfer from AM hyphae. The expression of TaNRT1.2 was also down-regulated by AM colonization even when there was no nutrient transfer from AM hyphae. The present study showed that an increase in carbon consumption by the AM fungi did not necessarily result in greater down-regulation of expression of Pi or N transporter genes.

A new AMS facility in Caserta/Italy

NASA Astrophysics Data System (ADS)

Terrasi, F.; Rogalla, D.; De Cesare, N.; D'Onofrio, A.; Lubritto, C.; Marzaioli, F.; Passariello, I.; Rubino, M.; Sabbarese, C.; Casa, G.; Palmieri, A.; Gialanella, L.; Imbriani, G.; Roca, V.; Romano, M.; Sundquist, M.; Loger, R.

2007-06-01

A new AMS system has been installed at Center for Isotopic Research on Cultural and Environmental Heritage (CIRCE) in Caserta/Italy. It was built by National Electrostatics Corp. Middleton, WI/USA, and arrived at CIRCE in the middle of January 2005; the installation and the acceptance tests were completed at the end of February 2005. At first, the system is intended for Radiocarbon AMS; for future Al and Be AMS only minor upgrades are needed and the magnets are designed to bend heavy isotopes like Uranium. Concerning Radiocarbon AMS, the first measurements of unknown samples, prepared in the internal preparation laboratory, already yielded results of high precision and 14C dating is in full swing.

Correction of Rayleigh Scattering Effects in Cloud Optical Thickness Retrievals

NASA Technical Reports Server (NTRS)

Wang, Meng-Hua; King, Michael D.

1997-01-01

We present results that demonstrate the effects of Rayleigh scattering on the 9 retrieval of cloud optical thickness at a visible wavelength (0.66 Am). The sensor-measured radiance at a visible wavelength (0.66 Am) is usually used to infer remotely the cloud optical thickness from aircraft or satellite instruments. For example, we find that without removing Rayleigh scattering effects, errors in the retrieved cloud optical thickness for a thin water cloud layer (T = 2.0) range from 15 to 60%, depending on solar zenith angle and viewing geometry. For an optically thick cloud (T = 10), on the other hand, errors can range from 10 to 60% for large solar zenith angles (0-60 deg) because of enhanced Rayleigh scattering. It is therefore particularly important to correct for Rayleigh scattering contributions to the reflected signal from a cloud layer both (1) for the case of thin clouds and (2) for large solar zenith angles and all clouds. On the basis of the single scattering approximation, we propose an iterative method for effectively removing Rayleigh scattering contributions from the measured radiance signal in cloud optical thickness retrievals. The proposed correction algorithm works very well and can easily be incorporated into any cloud retrieval algorithm. The Rayleigh correction method is applicable to cloud at any pressure, providing that the cloud top pressure is known to within +/- 100 bPa. With the Rayleigh correction the errors in retrieved cloud optical thickness are usually reduced to within 3%. In cases of both thin cloud layers and thick ,clouds with large solar zenith angles, the errors are usually reduced by a factor of about 2 to over 10. The Rayleigh correction algorithm has been tested with simulations for realistic cloud optical and microphysical properties with different solar and viewing geometries. We apply the Rayleigh correction algorithm to the cloud optical thickness retrievals from experimental data obtained during the Atlantic Stratocumulus Transition Experiment (ASTEX) conducted near the Azores in June 1992 and compare these results to corresponding retrievals obtained using 0.88 Am. These results provide an example of the Rayleigh scattering effects on thin clouds and further test the Rayleigh correction scheme. Using a nonabsorbing near-infrared wavelength lambda (0.88 Am) in retrieving cloud optical thickness is only applicable over oceans, however, since most land surfaces are highly reflective at 0.88 Am. Hence successful global retrievals of cloud optical thickness should remove Rayleigh scattering effects when using reflectance measurements at 0.66 Am.

NASA Glenn Research Center Solar Cell Experiment Onboard the International Space Station

NASA Technical Reports Server (NTRS)

Myers, Matthew G.; Wolford, David S.; Prokop, Norman F.; Krasowski, Michael J.; Parker, David S.; Cassidy, Justin C.; Davies , William E.; Vorreiter, Janelle O.; Piszczor, Michael F.; Mcnatt, Jeremiah S.;

Photodynamic inactivation of microorganisms which cause pulmonary diseases with infrared light: an in vitro study

NASA Astrophysics Data System (ADS)

Leite, Ilaiáli S.; Geralde, Mariana C.; Salina, Ana C.; Medeiros, Alexandra I.; Kurachi, Cristina; Bagnato, Vanderlei S.; Inada, Natalia M.

2014-03-01

Lower respiratory infections are among the leading causes of death worldwide. In this study, it was evaluated the interaction of indocyanine green, a photosensitizer activated by infrared light, with alveolar macrophages and the effectiveness of the photodynamic therapy using this compound against Streptococcus pneumoniae . Initial experiments analyzed indocyanine green toxicity to alveolar macrophages in the dark with different drug concentrations and incubation times, and macrophage viability was obtained with the MTT method. The average of the results showed viability values below 90% for the two highest concentrations. Experiments with Streptococcus pneumoniae showed photodynamic inactivation with 10 μM indocyanine green solution. Further experiments with the bacteria in co-culture with AM will be conducted verifying the photodynamic inactivation effectiveness of the tested drug concentrations and incubation periods using infrared light.

Organic and Aqueous Redox Speciation of Cu(III) Periodate Oxidized Transuranium Actinides

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCann, Kevin; Sinkov, Sergey I.; Lumetta, Gregg J.

A hexavalent group actinide separation process could streamline used nuclear fuel recycle and waste management. The limiting factor to such a process compatible with current fuel dissolution practices is obtaining and maintaining hexavalent Am, in molar nitric acid due to the high reduction potential of the Am(VI)/Am(III) couple (1.68 V vs SCE). Two strong oxidants, sodium bismuthate and Cu(III) periodate, have demonstrated quantitative oxidation of Am under molar acid conditions and better than 50% recovery by diamyl amylphosphonate (DAAP) is possible under these same conditions. This work considers the use of Cu(III) periodate to oxidize Np(V) to Np(VI) and Pu(IV)more » to Pu(VI) and recover these elements by extraction with DAAP. A metal:oxidant ratio of 1:1.2 and 1:3 was necessary to quantitatively oxidize Np(V) and Pu(IV), respectively, to the hexavalent state. Extraction of hexavalent Np, Pu, and Am by 1 M DAAP in n-dodecane was measured using UV-Vis [Pu(VI), Am (VI)] and NIR [Np(VI)]. Distribution values of Am(VI) were found to match previous tracer level studies. The organic phase spectra of Np, Pu, and Am are presented and molar absorptivities are calculated for characteristic peaks. Hexavalent Pu was found to be stable in the organic phase while Np(VI) showed some reduction to Np(V) and Am was present as Am(III), Am(V), and Am(VI) species in aqueous and organic phases during the extraction experiments. These results demonstrate, for the first time, the ability to recover macroscopic amounts of americium that would be present during fuel reprocessing and are the first characterization of Am organic phase oxidation state speciation relevant to a hexavalent group actinide separation process under acidic conditions.« less

KSC-2010-5492

NASA Image and Video Library

2010-11-04

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the Alpha Magnetic Spectrometer-2 (AMS) sits in its cargo element work stand, where more processing will take place. AMS is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch Feb. 27, 2011. Photo credit: NASA/Jack Pfaller

Cooling Performance of Additively Manufactured Microchannels and Film Cooling Holes

NASA Astrophysics Data System (ADS)

Stimpson, Curtis K.

Additive manufacturing (AM) enables fabrication of components that cannot be made with any other manufacturing method. Significant advances in metal-based AM systems have made this technology feasible for building production parts to be used use in commercial products. In particular, the gas turbine industry benefits from AM as a manufacturing technique especially for development of components subjected to high heat flux. It has been shown that the use of microchannels in high heat flux components can lead to more efficient cooling designs than those that presently exist. The current manufacturing methods have prevented the use of microchannels in such parts, but AM now makes them manufacturable. However, before such designs can become a reality, much research must be done to characterize impacts on flow and heat transfer of AM parts. The current study considers the effect on flow and heat transfer through turbine cooling features made with AM. Specifically, the performance of microchannels and film cooling holes made with laser powder bed fusion (L-PBF) is assessed. A number of test coupons containing microchannels were built from high temperature alloy powders on a commercially available L-PBF machine. Pressure drop and heat transfer experiments characterized the flow losses and convective heat transfer of air passing through the channels at various Reynolds numbers and Mach numbers. The roughness of the channels' surfaces was characterized in terms of statistical roughness parameters; the morphology of the roughness was examined qualitatively. Magnitude and morphology of surface roughness found on AM parts is unlike any form of roughness seen in the literature. It was found that the high levels of roughness on AM surfaces result in markedly augmented pressure loss and heat transfer at all Reynolds numbers, and conventional flow and heat transfer correlations produce erroneous estimates. The physical roughness measurements made in this study were correlated to flow and heat transfer measurements to generate a predictive model for flow through AM microchannels. The flow compressibility was also found to play a significant role in flow loss through these channels. Overall effectiveness of film cooling combined with the internal microchannel flow was examined in a conjugate experimental setup. The validity of the experimental conditions was established by matching important dimensionless parameters of the experimental setup to common values found in turbine engines. These results showed that the roughness in the film cooling holes produced higher in-hole convection than those made with current manufacturing methods. The roughness in the holes also repressed the film performance. However, high relative roughness was shown to minimize the impact of coolant feed direction on the film effectiveness of the AM holes.

Progress Report, Grant AFOSR-79-0134, September 1, 1981 - August 31, 1982,

DTIC Science & Technology

1982-08-31

Math., 41, 4-3uO, S1. 40 R. Burridge Poroelasticity equations derived from J. B. Keller microstructure Pub: J. Acoust . Soc. Am., 70, 1140-1146, 1981...penny- J. D.’Achenbach shaped cracks in metals: Theory and L. Adler experiment D. K. Lewis Pub: J. Acoust . Soc. Am., 66, 1848-1856, 1979. 4 J.-M. Vanden...bPb: J. Acoust . Soc. Am., 68, 628-633, 1980. 16 J.-M. Vanden-Broeck Bubble or drop distortion in a straining flowJ. B. Keller in two dimensions Pub

Suitability of the microbial community composition and function in a semiarid mine soil for assessing phytomanagement practices based on mycorrhizal inoculation and amendment addition.

PubMed

Kohler, J; Caravaca, F; Azcón, R; Díaz, G; Roldán, A

2016-03-15

The recovery of species composition and functions of soil microbial community of degraded lands is crucial in order to guarantee the long-term self-sustainability of the ecosystems. A field experiment was carried out to test the influence of combining fermented sugar beet residue (SBR) addition and inoculation with the arbuscular mycorrhizal (AM) fungus Funneliformis mosseae on the plant growth parameters and microbial community composition and function in the rhizosphere of two autochthonous plant species (Dorycnium pentaphyllum L. and Asteriscus maritimus L.) growing in a semiarid soil contaminated by heavy metals. We analysed the phospholipid fatty acids (PLFAs), neutral lipids fatty acids (NLFAs) and enzyme activities to study the soil microbial community composition and function, respectively. The combined treatment was not effective for increasing plant growth. The SBR promoted the growth of both plant species, whilst the AM fungus was effective only for D. pentaphyllum. The effect of the treatments on plant growth was linked to shifts in the rhizosphere microbial community composition and function. The highest increase in dehydrogenase and β-glucosidase activities was recorded in SBR-amended soil. The SBR increased the abundance of marker PLFAs for saprophytic fungi, Gram+ and Gram- bacteria and actinobacteria, whereas the AM fungus enhanced the abundance of AM fungi-related NLFA and marker PLFAs for Gram- bacteria. Measurement of the soil microbial community composition and function was useful to assess the success of phytomanagement technologies in a semiarid, contaminated soil. Copyright © 2016 Elsevier Ltd. All rights reserved.

Application of Ti6Al7Nb Alloy for the Manufacture of Biomechanical Functional Structures (BFS) for Custom-Made Bone Implants.

PubMed

Szymczyk, Patrycja; Ziółkowski, Grzegorz; Junka, Adam; Chlebus, Edward

2018-06-08

Unlike conventional manufacturing techniques, additive manufacturing (AM) can form objects of complex shape and geometry in an almost unrestricted manner. AM’s advantages include higher control of local process parameters and a possibility to use two or more various materials during manufacture. In this work, we applied one of AM technologies, selective laser melting, using Ti6Al7Nb alloy to produce biomedical functional structures (BFS) in the form of bone implants. Five types of BFS structures (A1, A2, A3, B, C) were manufactured for the research. The aim of this study was to investigate such technological aspects as architecture, manufacturing methods, process parameters, surface modification, and to compare them with such functional properties such as accuracy, mechanical, and biological in manufactured implants. Initial in vitro studies were performed using osteoblast cell line hFOB 1.19 (ATCC CRL-11372) (American Type Culture Collection). The results of the presented study confirm high applicative potential of AM to produce bone implants of high accuracy and geometric complexity, displaying desired mechanical properties. The experimental tests, as well as geometrical accuracy analysis, showed that the square shaped (A3) BFS structures were characterized by the lowest deviation range and smallestanisotropy of mechanical properties. Moreover, cell culture experiments performed in this study proved that the designed and obtained implant’s internal porosity (A3) enhances the growth of bone cells (osteoblasts) and can obtain predesigned biomechanical characteristics comparable to those of the bone tissue.

Radionuclide Basics: Americium-241

EPA Pesticide Factsheets

Americium (chemical symbol Am) is a man-made radioactive metal that is solid under normal conditions. Exposure to a significant amount of Am-241 is generally unlikely. Small amounts are found in the soil, plants and water from nuclear weapons testing.

A&M. Hot liquid waste building (TAN616) under construction. Camera facing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Hot liquid waste building (TAN-616) under construction. Camera facing northeast. Date: November 25, 1953. INEEL negative no. 9232 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Low Cost, Upper Stage-Class Propulsion

NASA Technical Reports Server (NTRS)

Vickers, John

2015-01-01

The low cost, upper stage-class propulsion (LCUSP) element will develop a high strength copper alloy additive manufacturing (AM) process as well as critical components for an upper stage-class propulsion system that will be demonstrated with testing. As manufacturing technologies have matured, it now appears possible to build all the major components and subsystems of an upper stage-class rocket engine for substantially less money and much faster than traditionally done. However, several enabling technologies must be developed before that can happen. This activity will address these technologies and demonstrate the concept by designing, manufacturing, and testing the critical components of a rocket engine. The processes developed and materials' property data will be transitioned to industry upon completion of the activity. Technologies to enable the concept are AM copper alloy process development, AM post-processing finishing to minimize surface roughness, AM material deposition on existing copper alloy substrate, and materials characterization.

Opportunities in low-level radiocarbon microtracing: applications and new technology

PubMed Central

Vuong, Le Thuy; Song, Qi; Lee, Hee Joo; Roffel, Ad F; Shin, Seok-Ho; Shin, Young G; Dueker, Stephen R

2016-01-01

14C-radiolabeled (radiocarbon) drug studies are central to defining the disposition of therapeutics in clinical development. Concerns over radiation, however, have dissuaded investigators from conducting these studies as often as their utility may merit. Accelerator mass spectrometry (AMS), originally designed for carbon dating and geochronology, has changed the outlook for in-human radiolabeled testing. The high sensitivity of AMS affords human clinical testing with vastly reduced radiative (microtracing) and chemical exposures (microdosing). Early iterations of AMS were unsuitable for routine biomedical use due to the instruments’ large size and associated per sample costs. The situation is changing with advances in the core and peripheral instrumentation. We review the important milestones in applied AMS research and recent advances in the core technology platform. We also look ahead to an entirely new class of 14C detection systems that use lasers to measure carbon dioxide in small gas cells. PMID:28031933

Effects of self-relevant cues and cue valence on autobiographical memory specificity in dysphoria.

PubMed

Matsumoto, Noboru; Mochizuki, Satoshi

2017-04-01

Reduced autobiographical memory specificity (rAMS) is a characteristic memory bias observed in depression. To corroborate the capture hypothesis in the CaRFAX (capture and rumination, functional avoidance, executive capacity and control) model, we investigated the effects of self-relevant cues and cue valence on rAMS using an adapted Autobiographical Memory Test conducted with a nonclinical population. Hierarchical linear modelling indicated that the main effects of depression and self-relevant cues elicited rAMS. Moreover, the three-way interaction among valence, self-relevance, and depression scores was significant. A simple slope test revealed that dysphoric participants experienced rAMS in response to highly self-relevant positive cues and low self-relevant negative cues. These results partially supported the capture hypothesis in nonclinical dysphoria. It is important to consider cue valence in future studies examining the capture hypothesis.

Toward Personalized Control of Human Gut Bacterial Communities.

PubMed

David, Lawrence A

2018-01-01

A key challenge in microbiology will be developing tools for manipulating human gut bacterial communities. Our ability to predict and control the dynamics of these communities is now in its infancy. To manage human gut microbiota, I am developing methods in three research domains. First, I am refining in vitro tools to experimentally study gut microbes at high throughput and in controlled settings. Second, I am adapting "big data" techniques to overcome statistical challenges confronting microbiota modeling. Third, I am testing study designs that can streamline human testing of microbiota manipulations. Assembling these methods creates new challenges, including training scientists who can work across disciplines such as engineering, ecology, and medicine. Nevertheless, I envision that overcoming these obstacles will enable my group to construct platforms that can personalize microbiota treatments, particularly ones based on diet. More broadly, I anticipate that such platforms will have applications across fields such as agriculture, biotechnology, and environmental management.

"I just feel like I am broken. I am the worst pregnant woman ever": A qualitative exploration of the "at odds" experience of women's antenatal distress.

PubMed

Staneva, Aleksandra A; Bogossian, Fiona; Morawska, Alina; Wittkowski, Anja

2017-06-01

Advances in perinatal mental health research have provided valuable insights around risk factors for the overall development of maternal distress. However, there is still a limited understanding of the experience of women struggling emotionally during pregnancy. We explored how women view, experience, and interpret psychological distress antenatally. Eighteen Australian women participated in in-depth interviews that were analyzed thematically within a critical realist theoretical framework. We present and situate the current findings within the dominant discourse of the good mother, which arguably promotes guilt and stigma and results in women self-labeling as bad mothers.

Arbuscular Mycorrhizal Symbiosis with Arundo donax Decreases Root Respiration and Increases Both Photosynthesis and Plant Biomass Accumulation.

PubMed

Romero-Munar, Antònia; Del-Saz, Néstor Fernández; Ribas-Carbó, Miquel; Flexas, Jaume; Baraza, Elena; Florez-Sarasa, Igor; Fernie, Alisdair Robert; Gulías, Javier

2017-07-01

The effect of arbuscular mycorrhiza (AM) symbiosis on plant growth is associated with the balance between costs and benefits. A feedback regulation loop has been described in which the higher carbohydrate cost to plants for AM symbiosis is compensated by increases in their photosynthetic rates. Nevertheless, plant carbon balance depends both on photosynthetic carbon uptake and respiratory carbon consumption. The hypothesis behind this research was that the role of respiration in plant growth under AM symbiosis may be as important as that of photosynthesis. This hypothesis was tested in Arundo donax L. plantlets inoculated with Rhizophagus irregularis and Funneliformis mosseae. We tested the effects of AM inoculation on both photosynthetic capacity and in vivo leaf and root respiration. Additionally, analyses of the primary metabolism and ion content were performed in both leaves and roots. AM inoculation increased photosynthesis through increased CO 2 diffusion and electron transport in the chloroplast. Moreover, respiration decreased only in AM roots via the cytochrome oxidase pathway (COP) as measured by the oxygen isotope technique. This decline in the COP can be related to the reduced respiratory metabolism and substrates (sugars and tricarboxylic acid cycle intermediates) observed in roots. © 2017 John Wiley & Sons Ltd.

A Comparison of Internal Dispositions and Career Trajectories after Collaborative versus Apprenticed Research Experiences for Undergraduates

PubMed Central

Frantz, Kyle J.; Demetrikopoulos, Melissa K.; Britner, Shari L.; Carruth, Laura L.; Williams, Brian A.; Pecore, John L.; DeHaan, Robert L.; Goode, Christopher T.

2017-01-01

Undergraduate research experiences confer benefits on students bound for science, technology, engineering, and mathematics (STEM) careers, but the low number of research professionals available to serve as mentors often limits access to research. Within the context of our summer research program (BRAIN), we tested the hypothesis that a team-based collaborative learning model (CLM) produces student outcomes at least as positive as a traditional apprenticeship model (AM). Through stratified, random assignment to conditions, CLM students were designated to work together in a teaching laboratory to conduct research according to a defined curriculum led by several instructors, whereas AM students were paired with mentors in active research groups. We used pre-, mid-, and postprogram surveys to measure internal dispositions reported to predict progress toward STEM careers, such as scientific research self-efficacy, science identity, science anxiety, and commitment to a science career. We are also tracking long-term retention in science-related career paths. For both short- and longer-term outcomes, the two program formats produced similar benefits, supporting our hypothesis that the CLM provides positive outcomes while conserving resources, such as faculty mentors. We discuss this method in comparison with course-based undergraduate research and recommend its expansion to institutional settings in which mentor resources are scarce. PMID:28130268

Antinociceptive effects of HUF-101, a fluorinated cannabidiol derivative.

PubMed

Silva, Nicole R; Gomes, Felipe V; Fonseca, Miriam D; Mechoulam, Raphael; Breuer, Aviva; Cunha, Thiago M; Guimarães, Francisco S

2017-10-03

Cannabidiol (CBD) is a phytocannabinoid with multiple pharmacological effects and several potential therapeutic properties. Its low oral bioavailability, however, can limit its clinical use. Preliminary results indicate that fluorination of the CBD molecule increases its pharmacological potency. Here, we investigated whether HUF-101 (3, 10, and 30mg/kg), a fluorinated CBD analogue, would induce antinociceptive effects. HUF-101 effects were compared to those induced by CBD (10, 30, and 90mg/kg) and the cannabinoid CB 1/2 receptor agonist WIN55,212-2 (1, 3, and 5mg/kg). These drugs were tested in male Swiss mice submitted to the following models predictive to antinociceptive drugs: hot plate, acetic acid-induced writhing, and carrageenan-induced inflammatory hyperalgesia. To evaluate the involvement of CB 1 and CB 2 receptors in HUF-101 and CBD effects, mice received the CB 1 receptor antagonist AM251 (1 or 3mg/kg) or the CB 2 receptor antagonist AM630 (1 or 3mg/kg) 30min before HUF-101, CBD, or WIN55,212-2. In the hot plate test, HUF-101 (30mg/kg) and WIN55,212-2 (5mg/kg) induced antinociceptive effects, which were attenuated by the pretreatment with AM251 and AM630. In the abdominal writhing test, CBD (30 and 90mg/kg), HUF-101 (30mg/kg), and WIN55,212-2 (3 and 5mg/kg) induced antinociceptive effects indicated by a reduction in the number of writhing. Whereas the pretreatment with AM630 did not mitigate the effects induced by any drug in this test, the pretreatment with AM251 attenuated the effect caused by WIN55,212-2. In the carrageenan-induced hyperalgesia test, CBD (30 and 90mg/kg), HUF-101 (3, 10 and 30mg/kg) and WIN55,212-2 (1mg/kg) decreased the intensity of mechanical hyperalgesia measured by the electronic von Frey method. The effects of all compounds were attenuated by the pretreatment with AM251 and AM630. Additionally, we evaluated whether HUF-101 would induce the classic cannabinoid CB 1 receptor-mediated tetrad (hypolocomotion, catalepsy, hypothermia, and antinociception). Unlike WIN55,212-2, CBD and HUF-101 did not induce the cannabinoid tetrad. These findings show that HUF-101 produced antinociceptive effects at lower doses than CBD, indicating that the addition of fluoride improved its pharmacological profile. Furthermore, some of the antinociceptive effects of CBD and HUF-101 effects seem to involve the activation of CB 1 and CB 2 receptors. Copyright © 2017 Elsevier Inc. All rights reserved.

Who Am I? "I Am a Swifty!" Some Stories from EFL Learners

ERIC Educational Resources Information Center

Prapunta, Sudatip

2017-01-01

This paper aims to report stories of two Thai learners who were purposively selected from a quantitative study of 233 freshmen. They study English as a Foreign Language (EFL) in the monolingual context. They were formally interviewed three times about their L2 motivation and learning experiences using narrative inquiry. Narrative data were…

Arbuscular mycorrhizal fungi differ in their ability to regulate the expression of phosphate transportors in maize (Zea mays L.)

USDA-ARS?s Scientific Manuscript database

A greenhouse experiment was conducted to study the expression of two phosphate (P) transporter genes ZEAma:Pht1;3 (epidermal-expressed) and ZEAma:Pht1;6 (AM specific induced, and expressed around arbuscules) in maize root to colonization by different arbuscular mycorrhizal (AM) fungal inoculants. No...

Neural correlates of behavioral amplitude modulation sensitivity in the budgerigar midbrain

PubMed Central

Neilans, Erikson G.; Abrams, Kristina S.; Idrobo, Fabio; Carney, Laurel H.

2016-01-01

Amplitude modulation (AM) is a crucial feature of many communication signals, including speech. Whereas average discharge rates in the auditory midbrain correlate with behavioral AM sensitivity in rabbits, the neural bases of AM sensitivity in species with human-like behavioral acuity are unexplored. Here, we used parallel behavioral and neurophysiological experiments to explore the neural (midbrain) bases of AM perception in an avian speech mimic, the budgerigar (Melopsittacus undulatus). Behavioral AM sensitivity was quantified using operant conditioning procedures. Neural AM sensitivity was studied using chronically implanted microelectrodes in awake, unrestrained birds. Average discharge rates of multiunit recording sites in the budgerigar midbrain were insufficient to explain behavioral sensitivity to modulation frequencies <100 Hz for both tone- and noise-carrier stimuli, even with optimal pooling of information across recording sites. Neural envelope synchrony, in contrast, could explain behavioral performance for both carrier types across the full range of modulation frequencies studied (16–512 Hz). The results suggest that envelope synchrony in the budgerigar midbrain may underlie behavioral sensitivity to AM. Behavioral AM sensitivity based on synchrony in the budgerigar, which contrasts with rate-correlated behavioral performance in rabbits, raises the possibility that envelope synchrony, rather than average discharge rate, might also underlie AM perception in other species with sensitive AM detection abilities, including humans. These results highlight the importance of synchrony coding of envelope structure in the inferior colliculus. Furthermore, they underscore potential benefits of devices (e.g., midbrain implants) that evoke robust neural synchrony. PMID:26843608

Activity Monitors as Support for Older Persons’ Physical Activity in Daily Life: Qualitative Study of the Users’ Experiences

PubMed Central

Eriksson, Lennie Carlén; Åkerberg, Nina; Johansson, Ann-Christin

2018-01-01

Background Falls are a major threat to the health and independence of seniors. Regular physical activity (PA) can prevent 40% of all fall injuries. The challenge is to motivate and support seniors to be physically active. Persuasive systems can constitute valuable support for persons aiming at establishing and maintaining healthy habits. However, these systems need to support effective behavior change techniques (BCTs) for increasing older adults’ PA and meet the senior users’ requirements and preferences. Therefore, involving users as codesigners of new systems can be fruitful. Prestudies of the user’s experience with similar solutions can facilitate future user-centered design of novel persuasive systems. Objective The aim of this study was to investigate how seniors experience using activity monitors (AMs) as support for PA in daily life. The addressed research questions are as follows: (1) What are the overall experiences of senior persons, of different age and balance function, in using wearable AMs in daily life?; (2) Which aspects did the users perceive relevant to make the measurements as meaningful and useful in the long-term perspective?; and (3) What needs and requirements did the users perceive as more relevant for the activity monitors to be useful in a long-term perspective? Methods This qualitative interview study included 8 community-dwelling older adults (median age: 83 years). The participants’ experiences in using two commercial AMs together with tablet-based apps for 9 days were investigated. Activity diaries during the usage and interviews after the usage were exploited to gather user experience. Comments in diaries were summarized, and interviews were analyzed by inductive content analysis. Results The users (n=8) perceived that, by using the AMs, their awareness of own PA had increased. However, the AMs’ impact on the users’ motivation for PA and activity behavior varied between participants. The diaries showed that self-estimated physical effort varied between participants and varied for each individual over time. Additionally, participants reported different types of accomplished activities; talking walks was most frequently reported. To be meaningful, measurements need to provide the user with a reliable receipt of whether his or her current activity behavior is sufficient for reaching an activity goal. Moreover, praise when reaching a goal was described as motivating feedback. To be useful, the devices must be easy to handle. In this study, the users perceived wearables as easy to handle, whereas tablets were perceived difficult to maneuver. Users reported in the diaries that the devices had been functional 78% (58/74) of the total test days. Conclusions Activity monitors can be valuable for supporting seniors’ PA. However, the potential of the solutions for a broader group of seniors can significantly be increased. Areas of improvement include reliability, usability, and content supporting effective BCTs with respect to increasing older adults’ PA. PMID:29391342

Impact of Study Design on Reported Incidences of Acute Mountain Sickness: A Systematic Review.

PubMed

Waeber, Baptiste; Kayser, Bengt; Dumont, Lionel; Lysakowski, Christopher; Tramèr, Martin R; Elia, Nadia

2015-09-01

Published incidences of acute mountain sickness (AMS) vary widely. Reasons for this variation, and predictive factors of AMS, are not well understood. We aimed to identify predictive factors that are associated with the occurrence of AMS, and to test the hypothesis that study design is an independent predictive factor of AMS incidence. We did a systematic search (Medline, bibliographies) for relevant articles in English or French, up to April 28, 2013. Studies of any design reporting on AMS incidence in humans without prophylaxis were selected. Data on incidence and potential predictive factors were extracted by two reviewers and crosschecked by four reviewers. Associations between predictive factors and AMS incidence were sought through bivariate and multivariate analyses for different study designs separately. Association between AMS incidence and study design was assessed using multiple linear regression. We extracted data from 53,603 subjects from 34 randomized controlled trials, 44 cohort studies, and 33 cross-sectional studies. In randomized trials, the median of AMS incidences without prophylaxis was 60% (range, 16%-100%); mode of ascent and population were significantly associated with AMS incidence. In cohort studies, the median of AMS incidences was 51% (0%-100%); geographical location was significantly associated with AMS incidence. In cross-sectional studies, the median of AMS incidences was 32% (0%-68%); mode of ascent and maximum altitude were significantly associated with AMS incidence. In a multivariate analysis, study design (p=0.012), mode of ascent (p=0.003), maximum altitude (p<0.001), population (p=0.002), and geographical location (p<0.001) were significantly associated with AMS incidence. Age, sex, speed of ascent, duration of exposure, or history of AMS were inconsistently reported and therefore not further analyzed. Reported incidences and identifiable predictive factors of AMS depend on study design.

Rapid change of AM fungal community in a rain-fed wheat field with short-term plastic film mulching practice.

PubMed

Liu, Yongjun; Mao, Lin; He, Xinhua; Cheng, Gang; Ma, Xiaojun; An, Lizhe; Feng, Huyuan

2012-01-01

Plastic film mulching (PFM) is a widely used agricultural practice in the temperate semi-arid Loess Plateau of China. However, how beneficial soil microbes, arbuscular mycorrhizal (AM) fungi in particular, respond to the PFM practice is not known. Here, a field experiment was performed to study the effects of a 3-month short-term PFM practice on AM fungi in plots planted with spring wheat (Triticum aestivum L. cv. Dingxi-2) in the Loess Plateau. AM colonization, spore density, wheat spike weight, and grain phosphorus (P) content were significantly increased in the PFM treatments, and these changes were mainly attributable to changes in soil properties such as available P and soil moisture. Alkaline phosphatase activity was significantly higher in PFM soils, but levels of AM fungal-related glomalin were similar between treatments. A total of nine AM fungal phylotypes were detected in root samples based on AM fungal SSU rDNA analyses, with six and five phylotypes in PFM and no-PFM plots, respectively. Although AM fungal phylotype richness was not statistically different between treatments, the community compositions were different, with four and three specific phylotypes in the PFM and no-PFM plots, respectively. A significant and rapid change in AM fungal, wheat, and soil variables following PFM suggested that the functioning of the AM symbiosis had been changed in the wheat field under PFM. Future studies are needed to investigate whether PFM applied over a longer term has a similar effect on the AM fungal community and their functioning in an agricultural ecosystem.

Fungi in the future: Interannual variation and effects of atmospheric change on arbuscular mycorrhizal fungal communities

DOE PAGES

Cotton, T. E. Anne; Fitter, Alastair H.; Miller, R. Michael; ...

2015-01-05

Understanding the natural dynamics of arbuscular mycorrhizal (AM) fungi and their response to global environmental change is essential for the prediction of future plant growth and ecosystem functions. We investigated the long-term temporal dynamics and effect of elevated atmospheric carbon dioxide (CO 2) and ozone (O 3) concentrations on AM fungal communities. Molecular methods were used to characterize the AM fungal communities of soybean ( Glycine max) grown under elevated and ambient atmospheric concentrations of both CO 2 and O 3 within a free air concentration enrichment experiment in three growing seasons over 5 yr. Elevated CO 2 altered themore » community composition of AM fungi, increasing the ratio of Glomeraceae to Gigasporaceae. By contrast, no effect of elevated O 3 on AM fungal communities was detected. However, the greatest compositional differences detected were between years, suggesting that, at least in the short term, large-scale interannual temporal dynamics are stronger mediators than atmospheric CO 2 concentrations of AM fungal communities. We conclude that, although atmospheric change may significantly alter AM fungal communities, this effect may be masked by the influences of natural changes and successional patterns through time. We suggest that changes in carbon availability are important determinants of the community dynamics of AM fungi.« less

Novel aminobenzanthrone dyes for amyloid fibril detection

NASA Astrophysics Data System (ADS)

Vus, Kateryna; Trusova, Valeriya; Gorbenko, Galyna; Kirilova, Elena; Kirilov, Georgiy; Kalnina, Inta; Kinnunen, Paavo

2012-04-01

A series of novel fluorescent aminobenzanthrone dyes have been tested for their ability to identify and characterize the oligomeric and fibrillar aggregates of lysozyme. The parameters of the dye binding to native, oligomeric and fibrillar protein have been calculated from the results of fluorimetric titration. Furthermore, several additional quantities reflecting the preference of the probe to either pre-fibrillar or fibrillar protein aggregates, have been evaluated. Based on the comparative analysis of the recovered parameters, AM4 was recommended for selective detection of protein pre-fibrillar assemblies, while the dyes AM1, AM2, AM3 were selected as the most prospective amyloid tracers.

AMS Prototyping Activities

NASA Technical Reports Server (NTRS)

Burleigh, Scott

2008-01-01

This slide presentation reviews the activity around the Asynchronous Message Service (AMS) prototype. An AMS reference implementation has been available since late 2005. It is aimed at supporting message exchange both in on-board environments and over space links. The implementation incoroporates all mandatory elements of the draft recommendation from July 2007: (1) MAMS, AMS, and RAMS protocols. (2) Failover, heartbeats, resync. (3) "Hooks" for security, but no cipher suites included in the distribution. The performance is reviewed, and a Benchmark latency test over VxWorks Message Queues is shown as histograms of a count vs microseconds per 1000-byte message

Plasticity of signaling and mate choice in a trilling species of the Mecopoda complex (Orthoptera: Tettigoniidae).

PubMed

Krobath, I; Römer, H; Hartbauer, M

2017-01-01

Males of a trilling species in the Mecopoda complex produce conspicuous calling songs that consist of two motifs: an amplitude-modulated motif with alternating loud and soft segments (AM-motif) and a continuous, high-intensity trill. The function of these song motifs for female attraction and competition between males was investigated. We tested the hypothesis that males modify their signaling behavior depending on the social environment (presence/absence of females or rival males) when they compete for mates. Therefore, we analyzed acoustic signaling of males in three different situations: (1) solo singing, (2) acoustic interaction with another male, and (3) singing in the presence of a female. In addition, the preference of females for these song motifs and further song parameters was studied in two-choice experiments. As expected, females showed a preference for conspicuous and loud song elements, but nevertheless, males increased the proportion of the AM-motif in the presence of a female. In acoustic interactions, males reduced bout duration significantly compared to both other situations. However, song bouts in this situation still overlapped more than expected by chance, which indicates intentionally simultaneous singing. A multivariate statistical analysis revealed that the proportion of the AM-motif and the duration of loud segments within the AM-motif allow a reliable prediction of whether males sing in isolation, compete with another male, or sing in the presence of a female. These results indicate that the AM-motif plays a dominant role especially in close-range courtship and that males are challenged in finding a balance between attracting females and saving energy during repeated acoustic interactions. Males of acoustic insects often produce conspicuous calling songs that have a dual function in male-male competition and mate attraction. High signal amplitudes and signal rates are associated with high energetic costs for signal production. We would therefore predict that males adjust their signaling behavior according to their perception of the social context. Here we studied signal production and mate choice in a katydid, where males switch between loud and soft song segments in a dynamic way. Additionally, we examined the attractiveness of different song elements in female choice tests. Our results show how males of this katydid deal with the conflict of remaining attractive for females and competing with a costly signal with rivals.

Environmental Cracking and Irradiation Resistant Stainless Steels by Additive Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rebak, Raul B.; Lou, Xiaoyuan

Metal additive manufacturing (AM), or metal 3D printing is an emergent advanced manufacturing method that can create near net shape geometries directly from computer models. This technology can provide the capability to rapidly fabricate complex parts that may be required to enhance the integrity of reactor internals components. Such opportunities may be observed during a plant refueling outage and AM parts can be rapidly custom designed, manufactured and deployed within the outage interval. Additive manufacturing of stainless steel (SS) components can add business benefits on fast delivery on repair hardware, installation tooling, new design prototypes tests, etc. For the nuclearmore » industry, the supply chain is always an issue for reactor service. AM can provide through-life supply chain (40-60 years) for high-value low-volume components. In the meantime, the capability of generating complex geometries and functional gradient materials will improve the performance, reduce the overall component cost, plant asset management cost and increase the plant reliability by the improvement in materials performance in nuclear environments. While extensive work has been conducted regarding additively manufacturing of austenitic SS parts, most efforts focused only on basic attributes such as porosity, residual stress, basic tensile properties, along with components yield and process monitoring. Little work has been done to define and evaluate the material requirements for nuclear applications. Technical gaps exist, which limit this technology adoption in the nuclear industry, which includes high manufacturing cost, unknown risks, limited nuclear related data, lack of specification and qualification methods, and no prior business experience. The main objective of this program was to generate research data to address all these technical gaps and establish a commercial practice to use AM technology in the nuclear power industry. The detailed objectives are listed as follows: (1) Evaluate nuclear related properties of AM 316L SS, including microstructure, tensile properties, impact toughness, stress corrosion cracking (SCC), corrosion fatigue (CF), irradiation effects, and irradiation assisted stress corrosion cracking (IASCC). (2) Understand the correlations among laser processing, heat treatment, microstructure and SCC/irradiation properties; (3) Optimize and improve the manufacturing process to achieve enhanced nuclear application properties; (4) Fabricate, evaluate, qualify and test a prototype reactor component to demonstrate the commercial viability and cost benefit; (5) Create regulatory approval path and commercialization plans for the production of a commercial reactor component.« less

Nutrient limitation drives response of Calamagrostis epigejos to arbuscular mycorrhiza in primary succession.

PubMed

Rydlová, Jana; Püschel, David; Dostálová, Magdalena; Janoušková, Martina; Frouz, Jan

2016-10-01

Little is known about the functioning of arbuscular mycorrhizal (AM) symbiosis over the course of primary succession, where soil, host plants, and AM fungal communities all undergo significant changes. Over the course of succession at the studied post-mining site, plant cover changes from an herbaceous community to the closed canopy of a deciduous forest. Calamagrostis epigejos (Poaceae) is a common denominator at all stages, and it dominates among AM host species. Its growth response to AM fungi was studied at four distinctive stages of natural succession: 12, 20, 30, and 50 years of age, each represented by three spatially separated sites. Soils obtained from all 12 studied sites were γ-sterilized and used in a greenhouse experiment in which C. epigejos plants were (1) inoculated with a respective community of native AM fungi, (2) inoculated with reference AM fungal isolates from laboratory collection, or (3) cultivated without AM fungi. AM fungi strongly boosted plant growth during the first two stages but not during the latter two, where the effect was neutral or even negative. While plant phosphorus (P) uptake was generally increased by AM fungi, no contribution of mycorrhizae to nitrogen (N) uptake was recorded. Based on N:P in plant biomass, we related the turn from a positive to a neutral/negative effect of AM fungi on plant growth, observed along the chronosequence, to a shift in relative P and N availability. No functional differences were found between native and reference inocula, yet root colonization by the native AM fungi decreased relative to the reference inoculum in the later succession stages, thereby indicating shifts in the composition of AM fungal communities reflected in different functional characteristics of their members.

Reduction Rates for Higher Americium Oxidation States in Nitric Acid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grimes, Travis Shane; Mincher, Bruce Jay; Schmitt, Nicholas C

The stability of hexavalent americium was measured using multiple americium concentrations and nitric acid concentrations after contact with the strong oxidant sodium bismuthate. Contrary to our hypotheses Am(VI) was not reduced faster at higher americium concentrations, and the reduction was only zero-order at short time scales. Attempts to model the reduction kinetics using zero order kinetic models showed Am(VI) reduction in nitric acid is more complex than the autoreduction processes reported by others in perchloric acid. The classical zero-order reduction of Am(VI) was found here only for short times on the order of a few hours. We did show thatmore » the rate of Am(V) production was less than the rate of Am(VI) reduction, indicating that some Am(VI) undergoes two electron-reduction to Am(IV). We also monitored the Am(VI) reduction in contact with the organic diluent dodecane. A direct comparison of these results with those in the absence of the organic diluent showed the reduction rates for Am(VI) were not statistically different for both systems. Additional americium oxidations conducted in the presence of Ce(IV)/Ce(III) ions showed that Am(VI) is reduced without the typical growth of Am(V) observed in the systems sans Ce ion. This was an interesting result which suggests a potential new reduction/oxidation pathway for Am in the presence of Ce; however, these results were very preliminary, and will require additional experiments to understand the mechanism by which this occurs. Overall, these studies have shown that hexavalent americium is fundamentally stable enough in nitric acid to run a separations process. However, the complicated nature of the reduction pathways based on the system components is far from being rigorously understood.« less

Arbuscular mycorrhizas enhance nutrient uptake in different wheat genotypes at high salinity levels under field and greenhouse conditions.

PubMed

Mardukhi, Baran; Rejali, Farhad; Daei, Gudarz; Ardakani, Mohammad Reza; Malakouti, Mohammad Javad; Miransari, Mohammad

2011-07-01

Since most experiments regarding the symbiosis between arbuscular mycorrhizal (AM) fungi and their host plants under salinity stress have been performed only under greenhouse conditions, this research work was also conducted under field conditions. The effects of three AM species including Glomus mosseae, G. etunicatum and G. intraradices on the nutrient uptake of different wheat cultivars (including Roshan, Kavir and Tabasi) under field and greenhouse (including Chamran and Line 9) conditions were determined. At field harvest, the concentrations of N, Ca, Mg, Fe, Cu, and Mn, and at greenhouse harvest, plant growth, root colonization and concentrations of different nutrients including N, K, P, Ca, Mg, Mn, Cu, Fe, Zn, Na and Cl were determined. The effects of wheat cultivars on the concentrations of N, Ca, and Mn, and of all nutrients were significant at field and greenhouse conditions, respectively. In both experiments, AM fungi significantly enhanced the concentrations of all nutrients including N, K, P, Ca, Mg, Mn, Cu, Fe, Zn, Na and Cl. The synergistic and enhancing effects of co-inoculation of AM species on plant growth and the inhibiting effect of AM species on Na(+) rather than on Cl(-) uptake under salinity are also among the important findings of this research work. Copyright © 2011 Académie des sciences. Published by Elsevier SAS. All rights reserved.

Intraspecific ploidy variation: A hidden, minor player in plant-soil-mycorrhizal fungi interactions.

PubMed

Sudová, Radka; Pánková, Hana; Rydlová, Jana; Münzbergová, Zuzana; Suda, Jan

2014-01-01

Genome duplication and arbuscular mycorrhizal (AM) symbiosis are ubiquitous in angiosperms. While the significance of each of these phenomena separately has been intensively studied, their interaction remains to be understood. Three diploid and three hexaploid populations of Aster amellus (Asteraceae) were characterized in terms of the soil conditions in situ and mycorrhizal root colonization. In a greenhouse experiment, the effects of ploidy level, substrate conditions, and AM fungi on plant performance were then separated by growing noninoculated plants or plants inoculated with AM fungi in substrates native to either the diploids or hexaploids. The diploids inhabited nutritionally richer sites but did not differ from hexaploid plants in the level of mycorrhizal root colonization in situ. In the experiment, hexaploids generally performed better than the diploids. This intercytotype growth difference was enhanced by soil fertility, with hexaploids benefiting more from nutritionally richer substrate than the diploids. AM inoculation was crucial for plant growth and phosphorus uptake. The interaction between ploidy level and AM inoculation significantly influenced only dry mass of roots, phosphorus concentrations in shoot biomass, and the length of the extraradical mycelium in the nonsterile substrates. Our results support the idea that polyploidy can affect the mycorrhizal growth response of host plants. Nevertheless, the effects of the interaction between ploidy and inoculation were weaker than the main effects of these factors.

Constraints on Leptophilic Dark Matter from the AMS-02 Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cavasonza, Leila Ali; Gast, Henning; Schael, Stefan

2017-04-10

The annihilation of dark matter particles in the Galactic halo of the Milky Way may lead to cosmic ray signatures that can be probed by the AMS-02 experiment, which has measured the composition and fluxes of charged cosmic rays with unprecedented precision. Given the absence of characteristic spectral features in the electron and positron fluxes measured by AMS-02, we derive upper limits on the dark matter annihilation cross section for leptophilic dark matter models. Our limits are based on a new background model that describes all recent measurements of the energy spectra of cosmic-ray positrons and electrons. For thermal darkmore » matter relics, we can exclude dark matter masses below about 100 GeV. We include the radiation of electroweak gauge bosons in the dark matter annihilation process and compute the antiproton signal that can be expected within leptophilic dark matter models.« less

Physical requirements and milestones for the HIT-PoP Experiment

NASA Astrophysics Data System (ADS)

Jarboe, Thomas

2011-10-01

Recent success with HIT-SI demonstrates the viability of steady inductive helicity injection (SIHI) as a spheromak formation and sustainment method. Results include the sustainment of toroidal current of over 50 kA, up to 40 kA of plasma current that is separate from the injectors, toroidal flux up to 6 times the peak injected flux, and j/n > 1014Am. All were achieved with 10MW or less applied power. This paper explores the requirements for a confinement test of the concept using a larger proof of principle experiment. The confinement experiment must not exceed the beta limit, the drift parameter limit, or the wall loading limit, where the drift parameter is (drift of electrons relative to ions to produce current)/(ion thermal speed). It must also exceed a minimum j/n, a minimum n a, and a minimum electron temperature, where a is the minor radius. The drift parameter limit and beta limit appear to play defining roles in spheromak performance leading to a very favorable scaling of wall loading with size. The milestones sequence suggested is the following: 1. Startup at drift parameter and beta limit minimum density. 2. Raise current until j/n exceeds 10-14Am. 3. Raise the current and temperature until T ~ 50 eV for good ionization. 4. Raise the current and density until n a > 2x1019 m-2 for neutral screening. 5. Raise current and temperature until T > 200eV so magnetic confinement can be studied.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richardson, B.; Robinson, B.; Mosher, T.

From 1982 through 1986, Philadelphia Electric Company (PECo) hosted the test of a communication system proposed for distribution automation and load management. The system included a utility control center (UCC), a broadcast interface unit in the AM station transmitter, and receiving units. To implement two-way communications, transmitters operating in the VHF spectrum at 154.463750 MHz were coupled with AM receivers. The VHF signal was received by four central receivers installed in the PECo service territory, and communicated to the UCC by either microwave or telephone links. The AM carrier signal provided communications and a synchronous time reference for the communicationmore » system. Station WCAU, 1210 kHz, was the broadcaster for the test. The test results confirmed the effectiveness of the AM broadcast link. However, in this particular implementation, the VHF link fell short of both expectation and acceptablity for return-path communications. The data is summarized and discussed in Volume I, and presented with additional detail in Volume II. A communications system consultant developed analytical models for the AM and VHF signal paths, and analyzed the data with respect to the models. Volume I of the two-volume report describes the communications system in general, presents the major data interpretations and conclusions, and describes the chronology and background for the project. It must be read and understood as a prerequisite for studying the information in Volume II. 14 figs., 1 tab.« less

Uptake and intracellular activity of AM-1155 in phagocytic cells.

PubMed Central

Yamamoto, T; Kusajima, H; Hosaka, M; Fukuda, H; Oomori, Y; Shinoda, H

1996-01-01

The uptake and intracellular activity of AM-1155 in murine J774.1 macrophages and human polymorphonuclear leukocytes were investigated. AM-1155 penetrated phagocytic cells rapidly and reversibly, although the penetration process was not affected by metabolic inhibitors such as sodium fluoride, cyanide m-chlorophenylhydrazone, or ouabain or by nucleoside transport system inhibitors such as adenosine. The intracellular concentration-to-extracellular concentration ratio of AM-1155 in both cell types of phagocytes ranged from 5 to 7. These ratios were almost equal to those for sparfloxacin. The intracellular activity of AM-1155 in J774.1 macrophages, examined with Staphylococcus aureus 209P as a test bacterium, was dependent on the extracellular concentration. AM-1155 at a concentration of 1 microgram/ml reduced the number of viable cells of S. aureus ingested by more than 90%. The intracellular activity of AM-1155 was more potent than those of sparfloxacin, ofloxacin, ciprofloxacin, flomoxef, and erythromycin. These results suggest that the potent intracellular activity of AM-1155 might mainly be due to the high intracellular concentration and its potent in vitro activity. PMID:9124835

Adrenalectomy for metastases from hepatocellular carcinoma - a single center experience.

PubMed

Popescu, Irinel; Alexandrescu, Sorin; Ciurea, Silviu; Brasoveanu, Vlad; Hrehoret, Doina; Gangone, Eliza; Boros, Mirela; Herlea, Vlad; Croitoru, Adina

2007-05-01

Adrenal metastases (AM) from hepatocellular carcinoma (HCC) are rarely seen in clinical practice. The treatment is not standardized, the indications and efficacy of different therapeutic approaches being still controversial. Between January 1995 and December 2005, 174 patients underwent liver resection for HCC in our center. AM were detected in four patients (2.3%): three of them had HCC and synchronous AM, and the remaining one developed AM 10 months after liver resection. All the patients with AM were treated by adrenalectomy (simultaneously with liver resection in synchronous metastases), followed by systemic chemotherapy. Non-resectable multifocal liver recurrences occurred in two patients, one of them having also a contralateral adrenal metastasis; these two patients are presently alive 26 and 43 months after adrenalectomy, respectively. Another patient died by liver recurrence 27 months postoperatively. The fourth patient is disease-free at 17 months after the initial operation. Adrenalectomy for AM from HCC should be performed whenever the primary tumor is well therapeutically controlled and the patient has a good performance status. Adrenalectomy offers the chance of more than 2 years survival in many patients. However, once AM are detected, the prognosis remains poor.

Synthesis, characterization and DFT-modeling of novel agents for the protection and restoration of historical calcareous stone substrates.

PubMed

Maiore, Laura; Aragoni, M Carla; Carcangiu, Gianfranco; Cocco, Ombretta; Isaia, Francesco; Lippolis, Vito; Meloni, Paola; Murru, Arianna; Tuveri, Enrica; Arca, Massimiliano

2015-06-15

The ammonium salts of oxamate (AmOxam) and monomethyloxalate (AmMeox), structurally related to ammonium oxalate (AmOx), were synthesized and characterized as protecting agents/filler for calcareous stone substrates. Both compounds featured an improved solubility in water and alcoholic-water mixtures with respect to AmOx. While AmOxam is stable in aqueous solution and reacts with calcite to afford the corresponding insoluble calcium oxamate (CaOxam), AmMeox spontaneously undergoes hydrolysis to give ammonium monohydrogen oxalate hemihydrate (AmBiox) and calcium oxalate (CaOx). Both compounds have been tested for the restoration of naturally weathered marble and biomicritic limestone. The formation of a superficial layer of CaOxam and CaOx was observed on stone samples treated with AmOxam and AmMeox, respectively, depending on the solvent mixture. A quantum-mechanical study was carried out at DFT level in order to investigate the nature of the interactions occurring between the lithic substrate (calcite) and the passivating agents, showing how the structural modifications on oxalic acid derivatives can be exploited to fine-tune their interaction with the calcite surface. Copyright © 2015 Elsevier Inc. All rights reserved.

Teaching medical students a clinical approach to altered mental status: simulation enhances traditional curriculum

PubMed Central

Sperling, Jeremy D.; Clark, Sunday; Kang, Yoon

2013-01-01

Introduction Simulation-based medical education (SBME) is increasingly being utilized for teaching clinical skills in undergraduate medical education. Studies have evaluated the impact of adding SBME to third- and fourth-year curriculum; however, very little research has assessed its efficacy for teaching clinical skills in pre-clerkship coursework. To measure the impact of a simulation exercise during a pre-clinical curriculum, a simulation session was added to a pre-clerkship course at our medical school where the clinical approach to altered mental status (AMS) is traditionally taught using a lecture and an interactive case-based session in a small group format. The objective was to measure simulation's impact on students’ knowledge acquisition, comfort, and perceived competence with regards to the AMS patient. Methods AMS simulation exercises were added to the lecture and small group case sessions in June 2010 and 2011. Simulation sessions consisted of two clinical cases using a high-fidelity full-body simulator followed by a faculty debriefing after each case. Student participation in a simulation session was voluntary. Students who did and did not participate in a simulation session completed a post-test to assess knowledge and a survey to understand comfort and perceived competence in their approach to AMS. Results A total of 154 students completed the post-test and survey and 65 (42%) attended a simulation session. Post-test scores were higher in students who attended a simulation session compared to those who did not (p<0.001). Students who participated in a simulation session were more comfortable in their overall approach to treating AMS patients (p=0.05). They were also more likely to state that they could articulate a differential diagnosis (p=0.03), know what initial diagnostic tests are needed (p=0.01), and understand what interventions are useful in the first few minutes (p=0.003). Students who participated in a simulation session were more likely to find the overall AMS curriculum useful (p<0.001). Conclusion Students who participated in a simulation exercise performed better on a knowledge-based test and reported increased comfort and perceived competence in their clinical approach to AMS. SBME shows significant promise for teaching clinical skills to medical students during pre-clinical curriculum. PMID:23561054

Computed Tomography Inspection and Analysis for Additive Manufacturing Components

NASA Technical Reports Server (NTRS)

Beshears, Ronald D.

2017-01-01

Computed tomography (CT) inspection was performed on test articles additively manufactured from metallic materials. Metallic AM and machined wrought alloy test articles with programmed flaws and geometric features were inspected using a 2-megavolt linear accelerator based CT system. Performance of CT inspection on identically configured wrought and AM components and programmed flaws was assessed to determine the impact of additive manufacturing on inspectability of objects with complex geometries.

Influence of Acute Normobaric Hypoxia on Hemostasis in Volunteers with and without Acute Mountain Sickness

PubMed Central

Schaber, Marc; Leichtfried, Veronika; Fries, Dietmar; Wille, Maria; Gatterer, Hannes; Faulhaber, Martin; Würtinger, Philipp; Schobersberger, Wolfgang

2015-01-01

Introduction. The aim of the present study was to investigate whether a 12-hour exposure in a normobaric hypoxic chamber would induce changes in the hemostatic system and a procoagulant state in volunteers suffering from acute mountain sickness (AMS) and healthy controls. Materials and Methods. 37 healthy participants were passively exposed to 12.6% FiO2 (simulated altitude hypoxia of 4,500 m). AMS development was investigated by the Lake Louise Score (LLS). Prothrombin time, activated partial thromboplastin time, fibrinogen, and platelet count were measured and specific methods (i.e., thromboelastometry and a thrombin generation test) were used. Results. AMS prevalence was 62.2% (LLS cut off of 3). For the whole group, paired sample t-tests showed significant increase in the maximal concentration of generated thrombin. ROTEM measurements revealed a significant shortening of coagulation time and an increase of maximal clot firmness (InTEM test). A significant increase in maximum clot firmness could be shown (FibTEM test). Conclusions. All significant changes in coagulation parameters after exposure remained within normal reference ranges. No differences with regard to measured parameters of the hemostatic system between AMS-positive and -negative subjects were observed. Therefore, the hypothesis of the acute activation of coagulation by hypoxia can be rejected. PMID:26451374

Influence of Acute Normobaric Hypoxia on Hemostasis in Volunteers with and without Acute Mountain Sickness.

PubMed

Schaber, Marc; Leichtfried, Veronika; Fries, Dietmar; Wille, Maria; Gatterer, Hannes; Faulhaber, Martin; Würtinger, Philipp; Schobersberger, Wolfgang

2015-01-01

The aim of the present study was to investigate whether a 12-hour exposure in a normobaric hypoxic chamber would induce changes in the hemostatic system and a procoagulant state in volunteers suffering from acute mountain sickness (AMS) and healthy controls. 37 healthy participants were passively exposed to 12.6% FiO2 (simulated altitude hypoxia of 4,500 m). AMS development was investigated by the Lake Louise Score (LLS). Prothrombin time, activated partial thromboplastin time, fibrinogen, and platelet count were measured and specific methods (i.e., thromboelastometry and a thrombin generation test) were used. AMS prevalence was 62.2% (LLS cut off of 3). For the whole group, paired sample t-tests showed significant increase in the maximal concentration of generated thrombin. ROTEM measurements revealed a significant shortening of coagulation time and an increase of maximal clot firmness (InTEM test). A significant increase in maximum clot firmness could be shown (FibTEM test). All significant changes in coagulation parameters after exposure remained within normal reference ranges. No differences with regard to measured parameters of the hemostatic system between AMS-positive and -negative subjects were observed. Therefore, the hypothesis of the acute activation of coagulation by hypoxia can be rejected.

Archetype-based conversion of EHR content models: pilot experience with a regional EHR system.

PubMed

Chen, Rong; Klein, Gunnar O; Sundvall, Erik; Karlsson, Daniel; Ahlfeldt, Hans

2009-07-01

Exchange of Electronic Health Record (EHR) data between systems from different suppliers is a major challenge. EHR communication based on archetype methodology has been developed by openEHR and CEN/ISO. The experience of using archetypes in deployed EHR systems is quite limited today. Currently deployed EHR systems with large user bases have their own proprietary way of representing clinical content using various models. This study was designed to investigate the feasibility of representing EHR content models from a regional EHR system as openEHR archetypes and inversely to convert archetypes to the proprietary format. The openEHR EHR Reference Model (RM) and Archetype Model (AM) specifications were used. The template model of the Cambio COSMIC, a regional EHR product from Sweden, was analyzed and compared to the openEHR RM and AM. This study was focused on the convertibility of the EHR semantic models. A semantic mapping between the openEHR RM/AM and the COSMIC template model was produced and used as the basis for developing prototype software that performs automated bi-directional conversion between openEHR archetypes and COSMIC templates. Automated bi-directional conversion between openEHR archetype format and COSMIC template format has been achieved. Several archetypes from the openEHR Clinical Knowledge Repository have been imported into COSMIC, preserving most of the structural and terminology related constraints. COSMIC templates from a large regional installation were successfully converted into the openEHR archetype format. The conversion from the COSMIC templates into archetype format preserves nearly all structural and semantic definitions of the original content models. A strategy of gradually adding archetype support to legacy EHR systems was formulated in order to allow sharing of clinical content models defined using different formats. The openEHR RM and AM are expressive enough to represent the existing clinical content models from the template based EHR system tested and legacy content models can automatically be converted to archetype format for sharing of knowledge. With some limitations, internationally available archetypes could be converted to the legacy EHR models. Archetype support can be added to legacy EHR systems in an incremental way allowing a migration path to interoperability based on standards.

KSC-2011-2205

NASA Image and Video Library

2011-03-10

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, media check out the Alpha Magnetic Spectrometer-2 (AMS). AMS is a particle physics detector, designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS-2 will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch April 19 at 7:48 p.m. EDT. For more information visit, www.nasa.gov/mission_pages/shuttle/shuttlemissions/sts134/index.html. Photo credit: NASA/Glenn Benson

KSC-2011-2206

NASA Image and Video Library

2011-03-10

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, media check out the Alpha Magnetic Spectrometer-2 (AMS). AMS is a particle physics detector, designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS-2 will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch April 19 at 7:48 p.m. EDT. For more information visit, www.nasa.gov/mission_pages/shuttle/shuttlemissions/sts134/index.html. Photo credit: NASA/Glenn Benson

KSC-2011-2201

NASA Image and Video Library

2011-03-10

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, processing continues for the Alpha Magnetic Spectrometer-2 (AMS). AMS is a particle physics detector, designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS-2 will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch April 19 at 7:48 p.m. EDT. For more information visit, www.nasa.gov/mission_pages/shuttle/shuttlemissions/sts134/index.html. Photo credit: NASA/Glenn Benson

Arbuscular mycorrhizal fungi alleviate arsenic toxicity to Medicago sativa by influencing arsenic speciation and partitioning.

PubMed

Li, Jinglong; Sun, Yuqing; Jiang, Xuelian; Chen, Baodong; Zhang, Xin

2018-08-15

In a pot experiment, Medicago sativa inoculated with/without arbuscular mycorrhizal (AM) fungus Rhizophagus irregularis were grown in four levels (0, 10, 25, and 75 mg/kg) of arsenic (As)-polluted soil to investigate the influences of AM symbiosis on plant As tolerance. The results showed that mycorrhizal inoculation significantly increased plant biomass, while As addition decreased mycorrhizal colonization and hyphal length density. Mycorrhizal inoculation dramatically improved plant phosphorus (P) nutrition, restricted As uptake and retained more As in roots by upregulating the expression of the AM-induced P transporter gene MsPT4 and the metallothionein gene MsMT2. High soil As content downregulated MsPT4 expression. Dimethylarsenic acid (DMA) was detected only in the shoots of mycorrhizal plants, indicating that AM fungi likely play an essential role in As detoxification by biological methylation. The present investigation allowed deeper insights into the As detoxification mechanisms of AM associations and demonstrated the important role of AM fungi in plant resistance under As-contaminated conditions. Copyright © 2018 Elsevier Inc. All rights reserved.

Additive Manufacturing in Production: A Study Case Applying Technical Requirements

NASA Astrophysics Data System (ADS)

Ituarte, Iñigo Flores; Coatanea, Eric; Salmi, Mika; Tuomi, Jukka; Partanen, Jouni

Additive manufacturing (AM) is expanding the manufacturing capabilities. However, quality of AM produced parts is dependent on a number of machine, geometry and process parameters. The variability of these parameters affects the manufacturing drastically and therefore standardized processes and harmonized methodologies need to be developed to characterize the technology for end use applications and enable the technology for manufacturing. This research proposes a composite methodology integrating Taguchi Design of Experiments, multi-objective optimization and statistical process control, to optimize the manufacturing process and fulfil multiple requirements imposed to an arbitrary geometry. The proposed methodology aims to characterize AM technology depending upon manufacturing process variables as well as to perform a comparative assessment of three AM technologies (Selective Laser Sintering, Laser Stereolithography and Polyjet). Results indicate that only one machine, laser-based Stereolithography, was feasible to fulfil simultaneously macro and micro level geometrical requirements but mechanical properties were not at required level. Future research will study a single AM system at the time to characterize AM machine technical capabilities and stimulate pre-normative initiatives of the technology for end use applications.

Intercondylar roof impingement pressure after anterior cruciate ligament reconstruction in a porcine model.

PubMed

Iriuchishima, Takanori; Tajima, Goro; Ingham, Sheila J M; Shen, Wei; Horaguchi, Takashi; Saito, Akiyoshi; Smolinski, Patrick; Fu, Freddie H

2009-06-01

Anterior cruciate ligament (ACL) graft impingement against the intercondylar roof has been postulated, but not thoroughly investigated. The roof impingement pressure changes with different tibial and femoral tunnel positions in ACL reconstruction. Anterior tibial translation is also affected by the tunnel positions of ACL reconstruction. The study design included a controlled laboratory study. In 15 pig knees, the impingement pressure between ACL and intercondylar roof was measured using pressure sensitive film before and after ACL single bundle reconstruction. ACL reconstructions were performed in each knee with two different tibial and femoral tunnel position combinations: (1) tibial antero-medial (AM) tunnel to femoral AM tunnel (AM to AM) and (2) tibial postero-lateral (PL) tunnel to femoral High-AM tunnel (PL to High-AM). Anterior tibial translation (ATT) was evaluated after each ACL reconstruction using robotic/universal force-moment sensor testing system. Neither the AM to AM nor the PL to High-AM ACL reconstruction groups showed significant difference when compared with intact ACL in roof impingement pressure. The AM to AM group had a significantly higher failure load than PL to High-AM group. This study showed how different tunnel placements affect the ACL-roof impingement pressure and anterior-posterior laxity in ACL reconstruction. Anatomical ACL reconstruction does not cause roof impingement and it has a biomechanical advantage in ATT when compared with non-anatomical ACL reconstructions in the pig knee. There is no intercondylar roof impingement after anatomical single bundle ACL reconstruction.

Charting a Course through CORAL: Texas A&M University Libraries' Experience Implementing an Open-Source Electronic Resources Management System

ERIC Educational Resources Information Center

Hartnett, Eric; Beh, Eugenia; Resnick, Taryn; Ugaz, Ana; Tabacaru, Simona

2013-01-01

In 2010, after two previous unsuccessful attempts at electronic resources management system (ERMS) implementation, Texas A&M University (TAMU) Libraries set out once again to find an ERMS that would fit its needs. After surveying the field, TAMU Libraries selected the University of Notre Dame Hesburgh Libraries-developed, open-source ERMS,…

"I Can See You": An Autoethnography of My Teacher-Student Self

ERIC Educational Resources Information Center

Vasconcelos, Erika Franca de Souza

2011-01-01

This article is an autoethnographic investigation of my second-nature teacher-student self. What has made me into the teacher I am? What makes me the teacher I am? I draw upon my memories of my own teachers and students to address these questions. As I portray my teaching-learning experiences as textual "snapshots," I find that my dearest memories…

Now I Am NObody, See Me for Who I Am: The Paradox of Performativity

ERIC Educational Resources Information Center

Rich, Emma; Evans, John

2009-01-01

This paper draws on data collected from young white middle class women experiencing eating disorders to highlight what we refer to as the paradox of performativity in schools. In interviews with these young women on their schooling experiences, their narratives convey both a critique of the social conditions of their schooling and their subjugated…

Effectiveness of arbuscular mycorrhizal fungi in phytoremediation of lead- contaminated soil by vetiver grass.

PubMed

Bahraminia, Mahboobeh; Zarei, Mehdi; Ronaghi, Abdolmajid; Ghasemi-Fasaei, Reza

2016-01-01

A greenhouse experiment was conducted to evaluate the effectiveness of arbuscular mycorrhizal (AM) fungi in phytoremediation of lead (Pb)-contaminated soil by vetiver grass. Experiment was a factorial arranged in a completely randomized design. Factors included four Pb levels (50, 200, 400, and 800 mg kg(-1)) as Pb (NO3)2, AM fungi at three levels (non mycorrhizal (NM) control, Rhizophagus intraradices, Glomus versiforme). Shoot and root dry weights (SDW and RDW) decreased as Pb levels increased. Mycorrhizal inoculation increased SDW and RDW compared to NM control. With mycorrhizal inoculation and increasing Pb levels, Pb uptake of shoot and root increased compared to those of NM control. Root colonization increased with mycorrhizal inoculation but decreased as Pb levels increased. Phosphorus concentration and uptake in shoot of plants inoculated with AM fungi was significantly higher than NM control at 200 and 800 mg Pb kg(-1). The Fe concentration, Fe and Mn uptake of shoot in plants inoculated with Rhizophagus intraradices in all levels of Pb were significantly higher than NM control. Mycorrhizal inoculation increased Pb extraction, uptake and translocation efficiencies. Lead translocation factor decreased as Pb levels increased; however inoculation with AM fungi increased Pb translocation.

A&M. Radioactive parts security storage area. camera facing northwest. Outdoor ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Radioactive parts security storage area. camera facing northwest. Outdoor storage of concrete storage casks. Photographer: M. Holmes. Date: November 21, 1959. INEEL negative no. 59-6081 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

A&M. Hot liquid waste holding tanks. Camera faces southeast. Located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Hot liquid waste holding tanks. Camera faces southeast. Located in vicinity of TAN-616, hot liquid waste treatment plant. Date: November 13, 1953. INEEL negative no. 9159 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Search for Antimatter in Space with the Alpha Magnetic Spectrometer

NASA Astrophysics Data System (ADS)

Dirks, B. P. F.

Increasing distances between galaxies and the homogeneous low temperature cosmic radiation suggests the universe to be created out of a major explosion: the Big Bang. As the early hot universe expands and cools, matter starts to condense. Because of decoupling of forces, different forms of matter appear. Matter and antimatter should be created in even amounts. Therefore, one would expect the universe to be symmetric. However, no antimatter is found within a radius of 10 MPc from earth. In 1967 Sakharov argued that there must be 3 ingredients to create an asymmetric universe: baryonnummer violation, CP-violation and no thermal equilibrium during baryogenesis. Several theoretical models have been developed. Most of them exclude large amounts of antimatter, only a few allow for a symmetric universe. To verify these models, several cosmic ray experiments have been performed over the past thirty years. All of them were balloon experiments. The sensitivity of these experiments was not sufficient to give evidence for the existence of antimatter. The Alpha Magnetic Spectrometer (AMS) is built to derive a lower limit on the amount of antimatter in the Universe. This lower limit (or discovery!) may challenge present theories on the birth of the Universe. To reduce the background from anti-particles formed by collisions in our atmosphere, the detector will operate in space. The scientific goals of AMS are the following: (1) determination of the existence or non-existence of antimatter in de universe, (2) search for dark matter, which is believed to make up 90% of the universe, (3) other astrophysics like measurements on the ratio 10Be/910 which give information of cosmic ray transport. The AMS detector has been designed to identify particles in cosmic rays by measuring their charge, momentum, speed and energy deposition. Charged particles are bent in a magnetic dipole field. Their trajectory is reconstructed by a silicon tracker, which provides a measurement of energy loss as well. Triggering is done by the time-of-flight (TOF) system, which also measures energy deposition, and an anti- coincidence counter (ACC). The latter rejects particles from the side. Independent velocity measurement is done with a Cherenkov counter. A qualification test flight with AMS-01 on the Space Shuttle took place in 1998. During 184 hours of data taking 3x106 helium nuclei were collected. No anti-helium events were found. To extend the data taking period (and therefore improving statistics), an improved detector, AMS-02, will be installed on the International Space Station (ISS) in 2004. It will perform measurements on cosmic rays for three years. One expects to collect about 2x109 helium events. AMS-02 will set a firm limit on the ratio of antimatter over matter (in case of non-observation): anti-helium/helium < 1/109. With GEANT, a toolkit for the simulation of the passage of particles through matter, a complete detector description and response simulation is performed. Simulated events have been analyzed. It is shown that particle identification is possible by measuring speed as function of momentum up to the TeV level and by energy deposition. The determination of the efficiency of different sub-detectors is performed as well.

Meta-atom cluster acoustic metamaterial with broadband negative effective mass density

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Huaijun; Zhai, Shilong; Ding, Changlin

2014-02-07

We design a resonant meta-atom cluster, via which a two-dimensional (2D) acoustic metamaterial (AM) with broadband negative effective mass density from 1560 Hz to 5580 Hz is fabricated. Experimental results confirm that there is only weak interaction among the meta-atoms in the cluster. And then the meta-atoms in the cluster independently resonate, resulting in the cluster becoming equivalent to a broadband resonance unit. Extracted effective refractive indices from reflection and transmission measurements of the 2D AM appear to be negative from 1500 Hz to 5480 Hz. The broadband negative refraction has also been demonstrated by our further experiments. We expectmore » that this meta-atom cluster AM will significantly contribute to the design of broadband negative effective mass density AM.« less

Check-Up of Planet Earth at the Turn of the Millennium: Anticipated New Phase in Earth Sciences

NASA Technical Reports Server (NTRS)

Kaufman, Y. J.; Ramanathan, V.

1998-01-01

Langley's remarkable solar and lunar spectra collected from Mt. Whitney inspired Arrhenius to develop the first quantitative climate model in 1896. In 1999, NASA's Earth Observing AM Satellite (EOS-AM) will repeat Langley's experiment, but for the entire planet, thus pioneering calibrated spectral observations from space. Conceived in response to real environmental problems, EOS-AM, in conjunction with other international satellite efforts, will fill a major gap in current efforts by providing quantitative global data sets with a resolution of few kilometers on the physical, chemical and biological elements of the earth system. Thus, like Langley's data, EOS-AM can revolutionize climate research by inspiring a new generation of climate system models and enable us to assess the human impact on the environment.

Effect of high terrestrial altitude and supplemental oxygen on human performance and mood.

PubMed

Crowley, J S; Wesensten, N; Kamimori, G; Devine, J; Iwanyk, E; Balkin, T

1992-08-01

Sustained exposure to high terrestrial altitudes is associated with cognitive decrement, mood changes, and acute mountain sickness (AMS). Such impairment in aviators could be a safety hazard. Thirteen male soldiers, ages 19-24, ascended in 10 min from sea level to 4,300 m (simulated), and remained there 2.5 d. Four times per day, subjects completed a test battery consisting of nine cognitive tests, a mood scale, and an AMS questionnaire. During one test session per day, subjects breathed 35% oxygen instead of ambient air. Analysis revealed transient deficits on altitude day 1 for three cognitive tasks. Most tasks displayed a persistent training effect. Sick subjects' moods were more negative and their performance improvement less. On altitude day 1, oxygen administration improved performance on two cognitive tests and one mood subscale. Following rapid ascent to 4,300 m, performance is most affected during the first 8 h. Individuals affected by AMS tend to improve more slowly in performance and have more negative moods than those who feel well.

Further Analyses of the NASA Glenn Research Center Solar Cell and Photovoltaic Materials Experiment Onboard the International Space Station

NASA Technical Reports Server (NTRS)

Myers, Matthew G.; Prokop, Norman F.; Krasowski, Michael J.; Piszczor, Michael F.; McNatt, Jeremiah S.

2016-01-01

Accurate air mass zero (AM0) measurement is essential for the evaluation of new photovoltaic (PV) technology for space solar cells. The NASA Glenn Research Center (GRC) has flown an experiment designed to measure the electrical performance of several solar cells onboard NASA Goddard Space Flight Center's (GSFC) Robotic Refueling Mission's (RRM) Task Board 4 (TB4) on the exterior of the International Space Station (ISS). Four industry and government partners provided advanced PV devices for measurement and orbital environment testing. The experiment was positioned on the exterior of the station for approximately eight months, and was completely self-contained, providing its own power and internal data storage. Several new cell technologies including four-junction (4J) Inverted Metamorphic Multi-Junction (IMM) cells were evaluated and the results will be compared to ground-based measurement methods.

[Preparation and evaluation of novel mesoporous molecular sieve of baicalin surface molecularly imprinted polymers].

PubMed

Gu, Xia-li; He, Hong-liang; Shi, Li-ying; Gao, Yan-kun; Chen, Li-na

2015-05-01

Taking mesoporous molecular sieve MCM-41 as a substrate, baicalin (BA) as template, acrylamide (AM) as the functional monomer, ethylene glycol dimethacrylate (EGDMA) as a cross-linking agent, ethanol as solvent, under thermal polymerization initiator of azobis isobutyronitrilo (AIBN) , a kind of selective recognition of baicalin surface molecularly imprinted polymer was synthesized. The surface morphologies and characteristics of the MIPs were characterized by infrared spectroscopy (IR) and transmission electron microscope (TEM). The adsorption properties of polymer microsphere for the template were tested by the dynamic adsorption equilibrium experiments and static adsorption equilibrium experiments. The experiment showed that the imprinting process was successfully and the well-ordered one-dimensional pore structure of MCM-41 was still preserved. Furthermore, molecularly imprinted polymers had higher selective ability for BA, then provided a new method for the efficient separation and enrichment of baicalin active ingredients from medicinal plants Scutellaria baicalensis.

Prevalence of heroin markers in urine for pain management patients.

PubMed

Knight, Julie; Puet, Brandi L; DePriest, Anne; Heltsley, Rebecca; Hild, Cheryl; Black, David L; Robert, Timothy; Caplan, Yale H; Cone, Edward J

2014-10-01

Surveys of current trends indicate heroin abuse is associated with nonmedical use of pain relievers. Consequently, there is an interest in evaluating the presence of heroin-specific markers in chronic pain patients who are prescribed controlled substances. A total of 926,084 urine specimens from chronic pain patients were tested for heroin/diacetylmorphine (DAM), 6-acetylmorphine (6AM), 6-acetylcodeine (6AC), codeine (COD), and morphine (MOR). Heroin and markers were analyzed using liquid chromatography tandem mass spectrometry (LC-MS-MS). Opiates were analyzed following hydrolysis using LC-MS-MS. The prevalence of heroin use was 0.31%, as 2871 were positive for one or more heroin-specific markers including DAM, 6AM, or 6AC (a known contaminant of illicit heroin). Of these, 1884 were additionally tested for the following markers of illicit drug use: 3,4-methylenedioxymethamphetamine (MDMA), 3,4-methylenedioxyamphetamine (MDA), methamphetamine (MAMP), 11-nor-9-carboxy-Δ(9)-tetracannabinol (THCCOOH), and benzoylecgonine (BZE); 654 (34.7%) had positive findings for one or more of these analytes. The overall prevalence of heroin markers were as follows: DAM 1203 (41.9%), 6AM 2570 (89.5%), 6AC 1082 (37.7%). MOR was present in 2194 (76.4%) and absent (

HEP Data Grid Applications in Korea

NASA Astrophysics Data System (ADS)

Cho, Kihyeon; Oh, Youngdo; Son, Dongchul; Kim, Bockjoo; Lee, Sangsan

2003-04-01

We will introduce the national HEP Data Grid applications in Korea. Through a five-year HEP Data Grid project (2002-2006) for CMS, AMS, CDF, PHENIX, K2K and Belle experiments in Korea, the Center for High Energy Physics, Kyungpook National University in Korea will construct the 1,000 PC cluster and related storage system such as 1,200 TByte Raid disk system. This project includes one of the master plan to construct Asia Regional Data Center by 2006 for the CMS and AMS Experiments and DCAF(DeCentralized Analysis Farm) for the CDF Experiments. During the first year of the project, we have constructed a cluster of around 200 CPU's with a 50 TBytes of a storage system. We will present our first year's experience of the software and hardware applications for HEP Data Grid of EDG and SAM Grid testbeds.

Genetic variation in the response of the weed Ruellia nudiflora (Acanthaceae) to arbuscular mycorrhizal fungi.

PubMed

Ramos-Zapata, José Alberto; Campos-Navarrete, María José; Parra-Tabla, Víctor; Abdala-Roberts, Luis; Navarro-Alberto, Jorge

2010-04-01

The main goal of this work was to test for plant genetic variation in the phenotypic plasticity response of the weed Ruellia nudiflora to arbuscular mycorrhizal (AM) fungi inoculation. We collected plants in the field, kept them under homogeneous conditions inside a nursery, and then collected seeds from these parent plants to generate five inbred lines (i.e., genetic families). Half of the plants of each inbred line were inoculated with AM fungi while the other half were not (controls); a fully crossed experimental design was then used to test for the effects of treatment (with or without AM fungi inoculation) and inbred line (genetic family). For each plant, we recorded the number of leaves produced and the number of days it survived during a 2-month period. Results showed a strong positive treatment effect (plastic response to AM fungi inoculation) for leaf production and survival. Moreover, in terms of survival, the treatment effect differed between genetic families (significant genetic family by treatment interaction). These findings indicate that the positive effect of AM fungi on plant survival (and potentially also growth) differs across plant genotypes and that such condition may contribute to R. nudiflora's capacity to colonize new environments.

Facilitation between woody and herbaceous plants that associate with arbuscular mycorrhizal fungi in temperate European forests.

PubMed

Veresoglou, Stavros D; Wulf, Monika; Rillig, Matthias C

2017-02-01

In late-successional environments, low in available nutrient such as the forest understory, herbaceous plant individuals depend strongly on their mycorrhizal associates for survival. We tested whether in temperate European forests arbuscular mycorrhizal (AM) woody plants might facilitate the establishment of AM herbaceous plants in agreement with the mycorrhizal mediation hypothesis. We used a dataset spanning over 400 vegetation plots in the Weser-Elbe region (northwest Germany). Mycorrhizal status information was obtained from published resources, and Ellenberg indicator values were used to infer environmental data. We carried out tests for both relative richness and relative abundance of herbaceous plants. We found that the subset of herbaceous individuals that associated with AM profited when there was a high cover of AM woody plants. These relationships were retained when we accounted for environmental filtering effects using path analysis. Our findings build on the existing literature highlighting the prominent role of mycorrhiza as a coexistence mechanism in plant communities. From a nature conservation point of view, it may be possible to promote functional diversity in the forest understory through introducing AM woody trees in stands when absent.

Determining the dissolution rates of actinide glasses: A time and temperature Product Consistency Test study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel, W.E.; Best, D.R.

1995-12-01

Vitrification has been identified as one potential option for the e materials such as Americium (Am), Curium (Cm), Neptunium (Np), and Plutonium (Pu). A process is being developed at the Savannah River Site to safely vitrify all of the highly radioactive Am/Cm material and a portion of the fissile (Pu) actinide materials stored on site. Vitrification of the Am/Cm will allow the material to be transported and easily stored at the Oak Ridge National Laboratory. The Am/Cm glass has been specifically designed to be (1) highly durable in aqueous environments and (2) selectively attacked by nitric acid to allow recoverymore » of the valuable Am and Cm isotopes. A similar glass composition will allow for safe storage of surplus plutonium. This paper will address the composition, relative durability, and dissolution rate characteristics of the actinide glass, Loeffler Target, that will be used in the Americium/Curium Vitrification Project at Westinghouse Savannah River Company near Aiken, South Carolina. The first part discusses the tests performed on the Loeffler Target Glass concerning instantaneous dissolution rates. The second part presents information concerning pseudo-activation energy for the one week glass dissolution process.« less

Thyronamines are isozyme-specific substrates of deiodinases.

PubMed

Piehl, S; Heberer, T; Balizs, G; Scanlan, T S; Smits, R; Koksch, B; Köhrle, J

2008-06-01

3-Iodothyronamine (3-T 1 AM) and thyronamine (T AM) are novel endogenous signaling molecules that exhibit great structural similarity to thyroid hormones but apparently antagonize classical thyroid hormone (T(3)) actions. Their proposed biosynthesis from thyroid hormones would require decarboxylation and more or less extensive deiodination. Deiodinases (Dio1, Dio2, and Dio3) catalyze the removal of iodine from their substrates. Because a role of deiodinases in thyronamine biosynthesis requires their ability to accept thyronamines as substrates, we investigated whether thyronamines are converted by deiodinases. Thyronamines were incubated with isozyme-specific deiodinase preparations. Deiodination products were analyzed using a newly established method applying liquid chromatography and tandem mass spectrometry (LC-MS/MS). Phenolic ring deiodinations of 3,3',5'-triiodothyronamine (rT3AM), 3',5'-diiodothyronamine (3',5'-T2AM), and 3,3'-diiodothyronamine (3,3'-T2AM) as well as tyrosyl ring deiodinations of 3,5,3'-triiodothyronamine (T3AM) and 3,5-diiodothyronamine (3,5-T2AM) were observed with Dio1. These reactions were completely inhibited by the Dio1-specific inhibitor 6n-propyl-2-thiouracil (PTU). Dio2 containing preparations also deiodinated rT(3)AM and 3',5'-T2AM at the phenolic rings but in a PTU-insensitive fashion. All thyronamines with tyrosyl ring iodine atoms were 5(3)-deiodinated by Dio3-containing preparations. In functional competition assays, the newly identified thyronamine substrates inhibited an established iodothyronine deiodination reaction. By contrast, thyronamines that had been excluded as deiodinase substrates in LC-MS/MS experiments failed to show any effect in the competition assays, thus verifying the former results. These data support a role for deiodinases in thyronamine biosynthesis and contribute to confining the biosynthetic pathways for 3-T 1 AM and T 0 AM.

The AMS-02 RICH detector: Performance during ground-based data taking at CERN

NASA Astrophysics Data System (ADS)

Pereira, R.; AMS RICH Collaboration

2011-05-01

The Alpha Magnetic Spectrometer (AMS), whose final version AMS-02 is to be installed on the International Space Station (ISS) in 2011, is a detector designed to measure charged cosmic ray spectra with energies up to the TeV region and with high energy photon detection capability up to a few hundred GeV, using state-of-the art particle identification techniques. Among several detector subsystems, AMS includes a proximity focusing RICH detector enabling precise measurements of particle electric charge (charge identification up to the iron region) and velocity ( Δβ/β˜10-3 for Z=1, Δβ/β˜10-4 for Z=10-20). The optimization of the RICH reconstruction efficiency imposed a dual radiator configuration with 16 NaF tiles ( n=1.33) in the centre and 92 aerogel tiles ( n=1.050) in the outer region, a pixelized detection matrix with 680 Hamamatsu R7600-M16 photomultipliers (each with 4×4 pixels) and a highly reflective conical mirror to increase photon collection. After its assembly at CIEMAT in Madrid, the RICH was taken to CERN in January 2008 and integrated into the full AMS-02 detector. AMS-02 underwent a pre-assembly in 2008 without magnet followed by a second detector assembly with a superconducting magnet in 2009 and the final assembly with a permanent magnet in mid-2010. Cosmic events were acquired in the context of the 2008 pre-assembly and in 2009, and two beam tests from CERN SPS took place in 2010. Results obtained with data from ground-based tests on the RICH performance are presented. A comparison with the aerogel light yield obtained on previous beam tests with a prototype detector is also discussed.

STS-107 Commander Rick Husband takes a break during TCDT M113 training

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Commander Rick Husband takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. Instructor George Hoggard looks on over Husband's shoulder. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

STS-107 Payload Specialist Ilan Ramon takes a break during TCDT M113 training

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-107 Payload Specialist Ilan Ramon, the first Israeli astronaut, takes a break during training on the operation of an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

KSC-02pd1933

NASA Image and Video Library

2002-12-18

KENNEDY SPACE CENTER, FLA. -- STS-107 Commander Rick Husband operates an M113 armored personnel carrier during Terminal Countdown Demonstration Test activities, a standard part of launch preparations. From left, Payload Specialist Ilan Ramon, the first Israeli astronaut, Instructor George Hoggard, and Mission Specialists Laurel Clark (face obscured) and Kalpana Chawla enjoy the ride in the background. STS-107 is a mission devoted to research and will include more than 80 experiments that will study Earth and space science, advanced technology development, and astronaut health and safety. Launch is planned for Jan. 16, 2003, between 10 a.m. and 2 p.m. EST aboard Space Shuttle Columbia.

L.E.R.C.I.P. Internship Summary

NASA Technical Reports Server (NTRS)

Donovan, Owen

2004-01-01

I am currently working towards a double major in Computer Science and Electrical and Computer Engineering. My summer internship at NASA Glenn Research Center has allowed me to apply and further my knowledge of both of these fields. This summer is my second L.E.R.C.I.P. experience, and has worked out equally well as the first. I haven't been working on one single project this year, but instead have had a good variety of thinking work on. Thus far I have spend time on the following tasks: antenna measurements, high-temperature reliability testing, and left-handed metamaterials.

Organisational adaptation in an activist network: social networks, leadership, and change in al-Muhajiroun.

PubMed

Kenney, Michael; Horgan, John; Horne, Cale; Vining, Peter; Carley, Kathleen M; Bigrigg, Michael W; Bloom, Mia; Braddock, Kurt

2013-09-01

Social networks are said to facilitate learning and adaptation by providing the connections through which network nodes (or agents) share information and experience. Yet, our understanding of how this process unfolds in real-world networks remains underdeveloped. This paper explores this gap through a case study of al-Muhajiroun, an activist network that continues to call for the establishment of an Islamic state in Britain despite being formally outlawed by British authorities. Drawing on organisation theory and social network analysis, we formulate three hypotheses regarding the learning capacity and social network properties of al-Muhajiroun (AM) and its successor groups. We then test these hypotheses using mixed methods. Our methods combine quantitative analysis of three agent-based networks in AM measured for structural properties that facilitate learning, including connectedness, betweenness centrality and eigenvector centrality, with qualitative analysis of interviews with AM activists focusing organisational adaptation and learning. The results of these analyses confirm that al-Muhajiroun activists respond to government pressure by changing their operations, including creating new platforms under different names and adjusting leadership roles among movement veterans to accommodate their spiritual leader's unwelcome exodus to Lebanon. Simple as they are effective, these adaptations have allowed al-Muhajiroun and its successor groups to continue their activism in an increasingly hostile environment. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Effects of Fluid Load on Human Urine Characteristics Related to Workplace Drug testing

DTIC Science & Technology

2012-03-01

Human.subject.participation.was.approved. by.the.Institutional.Review.Boards.of.the.University.of. Oklahoma.Health. Sciences. Center. (OUHSC),.Okla- homa . City,. OK,. and. of...Ju st A fte r F lu id In ta ke (S am pl e 3) A t S to m ac h C le ar an ce (S am pl e 4) A t F irs t U rg e (S am pl e 5

Assessment of frequency specific auditory steady-state response using amplitude modulation with 2-order exponential envelope.

PubMed

Cevallos-Larrea, Pablo; Pereira, Thobias; Santos, Wagner; Frota, Silvana M; Infantosi, Antonio F; Ichinose, Roberto M; Tierra-Criollo, Carlos

2016-08-01

This study investigated the performance of Frequency Specific Auditory Steady-State Response (FS-ASSR) detection elicited by the amplitude modulated tone with 2-order exponential envelope (AM2), using objective response detection (ORD) techniques of Spectral F-Test (SFT) and Magnitude Squared Coherence (MSC). ASSRs from 24 normal hearing adults were obtained during binaural multi-tone stimulation of amplitude-modulation (AM) and AM2 at intensities of 60, 45 and 30 dBSPL. The carrier frequencies were 500, 1000, 2000, and 4000 Hz, modulated between 77 and 105 Hz. AM2 achieve FS-ASSR amplitudes higher than AM by 16%, 18% and 12% at 60, 45 and 30 dBSPL, respectively, with a major increase at 500 Hz (22.5%). AMS2PL increased the Detection Rate (DR) up to 8.3% at 500 Hz for 30 dBSPL, which is particularly beneficial for FS-ASSR detection near the hearing threshold. In addition, responses in 1000 and 4000 Hz were consistently increased. The MSC and SFT presented no differences in Detection Rate (DR). False Detection Rate (FDR) was close to 5% for both techniques and tones. Detection times to reach DR over 90% were 3.5 and 4.9 min at 60 and 45 dBSPL, respectively. Further investigation concerning efficient multiple FS-ASSR is still necessary, such as testing subjects with hearing loss.

Computed Tomography Inspection and Analysis for Additive Manufacturing Components

NASA Technical Reports Server (NTRS)

Beshears, Ronald D.

2016-01-01

Computed tomography (CT) inspection was performed on test articles additively manufactured from metallic materials. Metallic AM and machined wrought alloy test articles with programmed flaws were inspected using a 2MeV linear accelerator based CT system. Performance of CT inspection on identically configured wrought and AM components and programmed flaws was assessed using standard image analysis techniques to determine the impact of additive manufacturing on inspectability of objects with complex geometries.

Impact of Sleeping Altitude on Symptoms of Acute Mountain Sickness on Mt. Fuji.

PubMed

Horiuchi, Masahiro; Uno, Tadashi; Endo, Junko; Handa, Yoko; Hasegawa, Tatsuya

2018-05-09

Horiuchi, Masahiro, Tadashi Uno, Junko Endo, Yoko Handa, and Tatsuya Hasegawa. Impact of sleeping altitude on symptoms of acute mountain sickness on Mt. Fuji. High Alt Med Biol. 00:000-000, 2018. We sought to investigate the factors influencing acute mountain sickness (AMS) on Mt. Fuji in Japan, in particular, to assess the effects of sleeping altitude, by means of a questionnaire survey. This study involved 1932 participants who climbed Mt. Fuji, and obtained information regarding sex, age, and whether participants stayed at the mountain lodges. The AMS survey excluded the perceived sleep difficulties assessed with the Lake Louise Scoring (LLS) system for all climbers. The overall prevalence of AMS was 31.6% for all participants (LLS score ≥3 with headache, excluding sleep difficulties). A univariate analysis revealed that overnight stay at Mt. Fuji was associated with an increased prevalence of AMS, but that sex and age were not. For overnight lodgers, the mean sleeping altitude in participants with AMS was slightly higher than that in participants without AMS (p < 0.05). Moreover, participants who stayed above 2870 m were more likely to experience AMS than those who stayed below 2815 m (p < 0.001), but sex and age were not significantly associated with the probability of experiencing AMS. Staying overnight at a mountain lodge, especially one above 2870 m, may be associated with an increased prevalence of AMS on Mt. Fuji.

Thermal Hydraulic Computational Fluid Dynamics Simulations and Experimental Investigation of Deformed Fuel Assemblies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mays, Brian; Jackson, R. Brian

2017-03-08

The project, Toward a Longer Life Core: Thermal Hydraulic CFD Simulations and Experimental Investigation of Deformed Fuel Assemblies, DOE Project code DE-NE0008321, was a verification and validation project for flow and heat transfer through wire wrapped simulated liquid metal fuel assemblies that included both experiments and computational fluid dynamics simulations of those experiments. This project was a two year collaboration between AREVA, TerraPower, Argonne National Laboratory and Texas A&M University. Experiments were performed by AREVA and Texas A&M University. Numerical simulations of these experiments were performed by TerraPower and Argonne National Lab. Project management was performed by AREVA Federal Services.more » The first of a kind project resulted in the production of both local point temperature measurements and local flow mixing experiment data paired with numerical simulation benchmarking of the experiments. The project experiments included the largest wire-wrapped pin assembly Mass Index of Refraction (MIR) experiment in the world, the first known wire-wrapped assembly experiment with deformed duct geometries and the largest numerical simulations ever produced for wire-wrapped bundles.« less

Targeted killing of Leishmania donovani in vivo and in vitro with amphotericin B attached to functionalized carbon nanotubes.

PubMed

Prajapati, Vijay Kumar; Awasthi, Kalpana; Gautam, Shalini; Yadav, Thakur Prasad; Rai, Madhukar; Srivastava, Onkar Nath; Sundar, Shyam

2011-04-01

This study describes the antileishmanial efficacy of the novel drug formulation of amphotericin B (AmB) attached to functionalized carbon nanotubes (f-CNTs) and compares it with AmB. f-CNTs were prepared in a two-step chemical carboxylation and amidation process. The AmB was then attached to make f-CNT-AmB and its construction was confirmed by Fourier transform infrared (FTIR) spectroscopy and transmission electron microscopy (TEM). The cytotoxicity of the constructed compound, f-CNT-AmB, was assessed in vitro using the J774A.1 macrophage cell line and in vivo using healthy BALB/c mice. Antileishmanial activity of AmB and f-CNT-AmB was assessed in vitro using a macrophage (J774A.1 cell line) model of Leishmania donovani infection. Antileishmanial activity was assessed in vivo by comparing the parasite load of hamsters treated with a 5 day course of AmB, f-CNTs or f-CNT-AmB initiated at 30 days after infection with L. donovani parasites. The FTIR spectroscopy and TEM data demonstrate the successful attachment of AmB to f-CNTs. The in vitro cytotoxicity of AmB, f-CNTs and f-CNT-AmB was measured by the cytotoxic concentration required to kill 50% of the cells: 0.48±0.06 μg/mL; 7.31±1.16 μg/mL; 0.66±0.17 μg/mL, respectively, in the J774A.1 cell line. The in vivo toxicity assessment of the compounds in BALB/c mice revealed no hepatic or renal toxicity. Against intracellular amastigotes the in vitro antileishmanial efficacy of f-CNT-AmB was significantly higher than that of AmB (IC50 0.00234±0.00075 μg/mL versus 0.03263±0.00123 μg/mL; P≤0.0001). The percentage inhibition of amastigote replication in hamsters treated with f-CNT-AmB was significantly more than that with AmB (89.85%±2.93% versus 68.97%±1.84%; P=0.0004). The results of these experiments clearly demonstrate that f-CNT-AmB has significantly greater antileishmanial efficacy than AmB and had no significant cytotoxic effects.

Effects of arbuscular mycorrhizal inoculation and biochar amendment on maize growth, cadmium uptake and soil cadmium speciation in Cd-contaminated soil.

PubMed

Liu, Ling; Li, Jiwei; Yue, Feixue; Yan, Xinwei; Wang, Fayuan; Bloszies, Sean; Wang, Yanfang

2018-03-01

Experiments conducted to understand how arbuscular mycorrhizal (AM) inoculation or biochar application affect plant growth and heavy metal uptake have thus far looked at single applications of either soil amendment. There is little evidence of their synergistic effects, in particular for plants grown in cadmium (Cd) contaminated soil. We conducted a mesocosm experiment to investigate the effect of AM inoculation (Glomus intraradices BEG 141) and/or wheat-straw biochar amendment on maize (Zea mays L. cv. Hongdan No. 897) growth, antioxidant enzymatic activities, and Cd uptake, as well as soil Cd speciation under applications of 0, 3, 6 mg Cd per kg soil. Applying either AM inoculant or biochar alone significantly increased maize growth and reduced Cd uptake. Furthermore, solo AM inoculation alleviating Cd stress more fully than biochar, in turn facilitating maize growth and decreasing soil Cd translocation into plant tissue. Still, solo biochar amendment was more effective at inducing soil alkalinization and contributing to Cd immobilization. Adding biochar together with AM inoculant significantly promoted fungal populations compared to a control. Amending soil with AM inoculant and biochar together produced the largest increase in maize growth and decrease in tissue Cd concentrations. This effect was additive, with 79.1% greater biomass, 51.42%, 82.91%, 43.96% higher activities of superoxide dismutase (SOD), peroxidase (POD), catalase (CAT), and 50.06%, 67.19%, 58.04% and 76.19% lower Cd concentrations in roots, stems, leaves, and ears, respectively, at a 6 mg kg -1 Cd contamination rate. The combined treatment also had a synergistic effect on inducing soil alkalinization and causing Cd immobilization, and decreasing Cd phytoavailability and post-harvest transfer risks. These results suggest that AM inoculation in combination with biochar application may be applicable not only for maize production but also for phytostabilization of Cd-contaminated soil. Copyright © 2017 Elsevier Ltd. All rights reserved.

Performance and modeling of cesium ion exchange by ENGI neered form crystalline silicotitanates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anthony, R.G.; Gu, D.; Huckman, M.

1996-10-01

TAM-5, a hydrous crystalline silicotitanate (CST) powder developed by Sandia National Laboratories and Texas A&M University, and commercialized by UOP as IONSIV{reg_sign} Ion Exchanger Type IE-910, is a highly selective material for removing cesium and strontium from aqueous radioactive wastes such as those found at the Hanford site in Washington. An engineered form of the material suitable for column ion exchange type operations has been developed and tested. Data relevant to processing radioactive tank wastes including equilibrium distribution coefficients and column testing will be presented. The impact of exposure of the engineered form to chemically aggressive environments such as itmore » might experience during waste processing, and to the less aggressive environments it might experience during post processing storage has been assessed. The thermal stability of the material has also been evaluated. The experimental results have been integrated with an effort to model the material`s equilibrium and kinetic behavior.« less

Dynamics of arbuscular mycorrhizal fungal community structure and functioning along a nitrogen enrichment gradient in an alpine meadow ecosystem.

PubMed

Jiang, Shengjing; Liu, Yongjun; Luo, Jiajia; Qin, Mingsen; Johnson, Nancy Collins; Öpik, Maarja; Vasar, Martti; Chai, Yuxing; Zhou, Xiaolong; Mao, Lin; Du, Guozhen; An, Lizhe; Feng, Huyuan

2018-03-30

Nitrogen (N) availability is increasing dramatically in many ecosystems, but the influence of elevated N on the functioning of arbuscular mycorrhizal (AM) fungi in natural ecosystems is not well understood. We measured AM fungal community structure and mycorrhizal function simultaneously across an experimental N addition gradient in an alpine meadow that is limited by N but not by phosphorus (P). AM fungal communities at both whole-plant-community (mixed roots) and single-plant-species (Elymus nutans roots) scales were described using pyro-sequencing, and the mycorrhizal functioning was quantified using a mycorrhizal-suppression treatment in the field (whole-plant-community scale) and a glasshouse inoculation experiment (single-plant-species scale). Nitrogen enrichment progressively reduced AM fungal abundance, changed AM fungal community composition, and shifted mycorrhizal functioning towards parasitism at both whole-plant-community and E. nutans scales. N-induced shifts in AM fungal community composition were tightly linked to soil N availability and/or plant species richness, whereas the shifts in mycorrhizal function were associated with the communities of specific AM fungal lineages. The observed changes in both AM fungal community structure and functioning across an N enrichment gradient highlight that N enrichment of ecosystems that are not P-limited can induce parasitic mycorrhizal functioning and influence plant community structure and ecosystem sustainability. © 2018 The Authors. New Phytologist © 2018 New Phytologist Trust.

Factors affecting the availability of americium-241 to the rice plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adriano, D.C.

1979-11-01

Since there has been no published transuranic uptake data on the rice plant (Oryza sativa L.), greenhouse experiments were conducted to determine the effects of some factors on the uptake of /sup 241/Am by this crop. Results indicate that chelated /sup 241/Am (in the form of americium-241-diethylenetriaminepentaacetic acid) applied to the flood water was markedly taken up by the rice plant, compared to the nonchelated form. However, most of the accumulation of /sup 241/Am occurred in the vegetative parts and only trace amounts, if any, were translocated to the grain. Soil application of /sup 241/Am resulted in much lower uptake.more » Soil amendment with either diethylenetriaminepentaacetic acid (DTPA) or organic matter did not produce a discernible uptake pattern. A synthesis of published data on plant uptake of /sup 241/Am indicates that the concentration ratio (CR, a measure of availability of /sup 241/Am to the plants) values for /sup 241/Am for agricultural crops ranged from 10-/sup 6/ to 10/sup 1/ (from lowest to highest availability). Some factors that appear to influence /sup 241/Am uptake are as follows: plant parts (grain usually having lower CR), chelating agents (DTPA usually increasing the CR), organic matter (inconsistent effects although generally decreasing the CR), and lime (usually decreasing the CR).« less

Effects of co-inoculation with arbuscular mycorrhizal fungi and rhizobia on soybean growth as related to root architecture and availability of N and P.

PubMed

Wang, Xiurong; Pan, Qiang; Chen, Fengxian; Yan, Xiaolong; Liao, Hong

2011-04-01

Soybean plants can form tripartite symbiotic associations with rhizobia and arbuscular mycorrhizal (AM) fungi, but little is known about effects of co-inoculation with rhizobia and AM fungi on plant growth, or their relationships to root architecture as well as nitrogen (N) and phosphorus (P) availability. In the present study, two soybean genotypes contrasting in root architecture were grown in a field experiment to evaluate relationships among soybean root architecture, AMF colonization, and nodulation under natural conditions. Additionally, a soil pot experiment in greenhouse was conducted to investigate the effects of co-inoculation with rhizobia and AM fungi on soybean growth, and uptake of N and P. Our results indicated that there was a complementary relationship between root architecture and AMF colonization in the field. The deep root soybean genotype had greater AMF colonization at low P, but better nodulation with high P supply than the shallow root genotype. A synergistic relationship dependent on N and P status exists between rhizobia and AM fungi on soybean growth. Co-inoculation with rhizobia and AM fungi significantly increased soybean growth under low P and/or low N conditions as indicated by increased shoot dry weight, along with plant N and P content. There were no significant effects of inoculation under adequate N and P conditions. Furthermore, the effects of co-inoculation were related to root architecture. The deep root genotype, HN112, benefited more from co-inoculation than the shallow root genotype, HN89. Our results elucidate new insights into the relationship between rhizobia, AM fungi, and plant growth under limitation of multiple nutrients, and thereby provides a theoretical basis for application of co-inoculation in field-grown soybean.

A&M. TAN607. Special equipment services room. Workers are filling viewing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. TAN-607. Special equipment services room. Workers are filling viewing window with zinc bromide through tube penetrating concrete shield wall. Date: August 16, 1954. INEEL negative no. 11689 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

A&M. Special shielding materials. Stockpile of magnetite, used for making ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Special shielding materials. Stockpile of magnetite, used for making high-density concrete, and loading conveyor near TAN-607 construction site. Date: September 25, 1953. INEEL negative no. 8710 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Additively Manufactured Metals in Oxygen Systems Project

NASA Technical Reports Server (NTRS)

Tylka, Jonathan

2015-01-01

Metals produced by additive manufacturing methods, such as Powder Bed Fusion Technology, are now mature enough to be considered for qualification in human spaceflight oxygen systems. The mechanical properties of metals produced through AM processes are being systematically studied. However, it is unknown whether AM metals in oxygen applications may present an increased risk of flammability or ignition as compared to wrought metals of the same metallurgical composition due to increased porosity. Per NASA-STD-6001B materials to be used in oxygen system applications shall be based on flammability and combustion test data, followed by a flammability assessment. Without systematic flammability and ignition testing in oxygen there is no credible method for NASA to accurately evaluate the risk of using AM metals in oxygen systems.

[Comparison of the acrylamide level in microwaved popcorn with that of ordinarily heated one].

PubMed

Sun, Shiyu; Xia, Yongmei; Liu, Xuefeng; Hu, Xueyi

2007-03-01

To establish a method of examining acrylamide in cooked popcorn. Solid phase extraction/gas chromatography (SPE/GC) was established with N, N-dimethyl acrylamide as internal standard. The detection limit and the quantification limit were estimated at 3 microg/L and 10 microg/L, respectively, and the linear correlation coefficient was 0.9969. Seven commercial popcorn samples with different flavors were collected and tested in this paper. The RSD of acrylamide level of caramel sweet popcorn microwaved was 1.95 % (n = 6). When the commercial popcorns of caramel sweet and cream salted were microwaved (A and D) or conventional heated (A' and D'), the acrylamide levels reached [Am]A = 1017 microg/kg, [Am]D = 146.5 microg/kg, [Am]A, = 2206 microg/kg and [Am]D = 970.1 microg/kg, respectively. The microwaved popcorns tested are safer in general because the acrylamide level of them except that with high simple sugar content is obviously lower than that of ordinarily heated one.

Simulations of arctic mixed-phase clouds in forecasts with CAM3 and AM2 for M-PACE

DOE PAGES

Xie, Shaocheng; Boyle, James; Klein, Stephen A.; ...

2008-02-27

[1] Simulations of mixed-phase clouds in forecasts with the NCAR Atmosphere Model version 3 (CAM3) and the GFDL Atmospheric Model version 2 (AM2) for the Mixed-Phase Arctic Cloud Experiment (M-PACE) are performed using analysis data from numerical weather prediction centers. CAM3 significantly underestimates the observed boundary layer mixed-phase cloud fraction and cannot realistically simulate the variations of liquid water fraction with temperature and cloud height due to its oversimplified cloud microphysical scheme. In contrast, AM2 reasonably reproduces the observed boundary layer cloud fraction while its clouds contain much less cloud condensate than CAM3 and the observations. The simulation of themore » boundary layer mixed-phase clouds and their microphysical properties is considerably improved in CAM3 when a new physically based cloud microphysical scheme is used (CAM3LIU). The new scheme also leads to an improved simulation of the surface and top of the atmosphere longwave radiative fluxes. Sensitivity tests show that these results are not sensitive to the analysis data used for model initialization. Increasing model horizontal resolution helps capture the subgrid-scale features in Arctic frontal clouds but does not help improve the simulation of the single-layer boundary layer clouds. AM2 simulated cloud fraction and LWP are sensitive to the change in cloud ice number concentrations used in the Wegener-Bergeron-Findeisen process while CAM3LIU only shows moderate sensitivity in its cloud fields to this change. Furthermore, this paper shows that the Wegener-Bergeron-Findeisen process is important for these models to correctly simulate the observed features of mixed-phase clouds.« less

Simulations of Arctic mixed-phase clouds in forecasts with CAM3 and AM2 for M-PACE

NASA Astrophysics Data System (ADS)

Xie, Shaocheng; Boyle, James; Klein, Stephen A.; Liu, Xiaohong; Ghan, Steven

2008-02-01

Simulations of mixed-phase clouds in forecasts with the NCAR Atmosphere Model version 3 (CAM3) and the GFDL Atmospheric Model version 2 (AM2) for the Mixed-Phase Arctic Cloud Experiment (M-PACE) are performed using analysis data from numerical weather prediction centers. CAM3 significantly underestimates the observed boundary layer mixed-phase cloud fraction and cannot realistically simulate the variations of liquid water fraction with temperature and cloud height due to its oversimplified cloud microphysical scheme. In contrast, AM2 reasonably reproduces the observed boundary layer cloud fraction while its clouds contain much less cloud condensate than CAM3 and the observations. The simulation of the boundary layer mixed-phase clouds and their microphysical properties is considerably improved in CAM3 when a new physically based cloud microphysical scheme is used (CAM3LIU). The new scheme also leads to an improved simulation of the surface and top of the atmosphere longwave radiative fluxes. Sensitivity tests show that these results are not sensitive to the analysis data used for model initialization. Increasing model horizontal resolution helps capture the subgrid-scale features in Arctic frontal clouds but does not help improve the simulation of the single-layer boundary layer clouds. AM2 simulated cloud fraction and LWP are sensitive to the change in cloud ice number concentrations used in the Wegener-Bergeron-Findeisen process while CAM3LIU only shows moderate sensitivity in its cloud fields to this change. This paper shows that the Wegener-Bergeron-Findeisen process is important for these models to correctly simulate the observed features of mixed-phase clouds.

Electrochemical oxidation of bio-refractory dye in a simulated textile industry effluent using DSA electrodes in a filter-press type FM01-LC reactor.

PubMed

Rodríguez, Francisca A; Mateo, María N; Aceves, Juan M; Rivero, Eligio P; González, Ignacio

2013-01-01

This work presents a study on degradation of indigo carmine dye in a filter-press type FM01-LC reactor using Sb2O5-doped Ti/IrO2-SnO2 dimensionally stable anode (DSA) electrodes. Micro- and macroelectrolysis studies were carried out using solutions of 0.8 mM indigo carmine in 0.05 M NaCl, which resemble blue denim laundry industrial wastewater. Microelectrolysis results show the behaviour of DSA electrodes in comparison with the behaviour of boron-doped diamond (BDD) electrodes. In general, dye degradation reactions are carried out indirectly through active chlorine generated on DSA, whereas in the case of BDD electrodes more oxidizing species are formed, mainly OH radicals, on the electrode surface. The well-characterized geometry, flow pattern and mass transport of the FM01-LC reactor used in macroelectrolysis experiments allowed the evaluation of the effect of hydrodynamic conditions on the chlorine-mediated degradation rate. Four values of Reynolds number (Re) (93, 371, 464 and 557) at four current densities (50, 100, 150 and 200 A/m2) were tested. The results show that the degradation rate is independent of Re at low current density (50 A/m2) but becomes dependent on the Re at high current density (200 A/m2). This behaviour shows the central role of mass transport and the reactor parameters and design. The low energy consumption (2.02 and 9.04 kWh/m3 for complete discolouration and chemical oxygen demand elimination at 50 A/m2, respectively) and the low cost of DSA electrodes compared to BDD make DSA electrodes promising for practical application in treating industrial textile effluents. In the present study, chlorinated organic compounds were not detected.

A Study of the quality of CsI detectors and pulse-shape discrimination of scintillators for ?[U+0251]-particles, ?[U+0263]-particles, and neutrons

NASA Astrophysics Data System (ADS)

Salyer, Kaitlin; Rogachev, Grigory; Hooker, Joshua

2016-09-01

This project studied the capabilities of two different scintillators, Cesium Iodide (CsI) and p-Terphenyl. First, the resolution of a CsI detector was investigated by exposing only very small areas of its surface at a time to an alpha source. Second, the abilities of p-Terphenyl to detect alpha particles, gamma particles, and neutrons were analyzed through pulse shape discrimination. p-Terphenyl is of particular interest because it will be used in the Mitchell Institute Neutrino Experiment at Reactor (MINER) at Texas A&M University for measuring background data. The information learned from conducting these tests will be useful in understanding and expanding the limits of the experiments in which these detectors will ultimately be used.

Occupational Health and Safety of Finnish Dairy Farmers Using Automatic Milking Systems.

PubMed

Karttunen, Janne P; Rautiainen, Risto H; Lunner-Kolstrup, Christina

2016-01-01

Conventional pipeline and parlor milking expose dairy farmers and workers to adverse health outcomes. In recent years, automatic milking systems (AMS) have gained much popularity in Finland, but the changes in working conditions when changing to AMS are not well known. The aim of this study was to investigate the occupational health and safety risks in using AMS, compared to conventional milking systems (CMS). An anonymous online survey was sent to each Finnish dairy farm with an AMS in 2014. Only those dairy farmers with prior work experience in CMS were included in the final analysis consisting of frequency distributions and descriptive statistics. We received 228 usable responses (131 male and 97 female; 25.2% response rate). The majority of the participants found that AMS had brought flexibility to the organization of farm work, and it had increased leisure time, quality of life, productivity of dairy work, and the attractiveness of dairy farming among the younger generation. In addition, AMS reduced the perceived physical strain on the musculoskeletal system as well as the risk of occupational injuries and diseases, compared to CMS. However, working in close proximity to the cattle, particularly training of heifers to use the AMS, was regarded as a high-risk work task. In addition, the daily cleaning of the AMS and manual handling of rejected milk were regarded as physically demanding. The majority of the participants stated that mental stress caused by the monotonous, repetitive, paced, and hurried work had declined after changing to AMS. However, many indicated increased mental stress because of the demanding management of the AMS. Nightly alarms caused by the AMS, lack of adequately skilled hired labor or farm relief workers, and the 24/7 standby for the AMS were issues that also caused mental stress. Based on this study, AMS may have significant potential in the prevention of adverse health outcomes in milking of dairy cows. In addition, AMS may improve the productivity of dairy work and sustainability of dairy production. However, certain characteristics of the AMS require further attention with regard to occupational health and safety risks.

Mechanical and Fatigue Properties of Additively Manufactured Metallic Materials

NASA Astrophysics Data System (ADS)

Yadollahi, Aref

This study aims to investigate the mechanical and fatigue behavior of additively manufactured metallic materials. Several challenges associated with different metal additive manufacturing (AM) techniques (i.e. laser-powder bed fusion and direct laser deposition) have been addressed experimentally and numerically. Experiments have been carried out to study the effects of process inter-layer time interval--i.e. either building the samples one-at-a-time or multi-at-a-time (in-parallel)--on the microstructural features and mechanical properties of 316L stainless steel samples, fabricated via a direct laser deposition (DLD). Next, the effect of building orientation--i.e. the orientation in which AM parts are built--on microstructure, tensile, and fatigue behaviors of 17-4 PH stainless steel, fabricated via a laser-powder bed fusion (L-PBF) method was investigated. Afterwards, the effect of surface finishing--here, as-built versus machined--on uniaxial fatigue behavior and failure mechanisms of Inconel 718 fabricated via a laser-powder bed fusion technique was sought. The numerical studies, as part of this dissertation, aimed to model the mechanical behavior of AM materials, under monotonic and cyclic loading, based on the observations and findings from the experiments. Despite significant research efforts for optimizing process parameters, achieving a homogenous, defect-free AM product--immediately after fabrication--has not yet been fully demonstrated. Thus, one solution for ensuring the adoption of AM materials for application should center on predicting the variations in mechanical behavior of AM parts based on their resultant microstructure. In this regard, an internal state variable (ISV) plasticity-damage model was employed to quantify the damage evolution in DLD 316L SS, under tensile loading, using the microstructural features associated with the manufacturing process. Finally, fatigue behavior of AM parts has been modeled based on the crack-growth concept. Using the FASTRAN code, the fatigue-life of L-PBF Inconel 718 was accurately calculated using the size and shape of process-induced voids in the material. In addition, the maximum valley depth of the surface profile was found to be an appropriate representative of the initial surface flaw for fatigue-life prediction of AM materials in an as-built surface condition.

Asymmetric response of root-associated fungal communities of an arbuscular mycorrhizal grass and an ectomycorrhizal tree to their coexistence in primary succession.

PubMed

Knoblochová, Tereza; Kohout, Petr; Püschel, David; Doubková, Pavla; Frouz, Jan; Cajthaml, Tomáš; Kukla, Jaroslav; Vosátka, Miroslav; Rydlová, Jana

2017-11-01

The arbuscular mycorrhizal (AM) grass Calamagrostis epigejos and predominantly ectomycorrhizal (EcM) tree Salix caprea co-occur at post-mining sites spontaneously colonized by vegetation. During succession, AM herbaceous vegetation is replaced by predominantly EcM woody species. To better understand the interaction of AM and EcM plants during vegetation transition, we studied the reciprocal effects of these species' coexistence on their root-associated fungi (RAF). We collected root and soil samples from three different microenvironments: stand of C. epigejos, under S. caprea canopy, and contact zone where roots of the two species interacted. RAF communities and mycorrhizal colonization were determined in sampled roots, and the soil was tested for EcM and AM inoculation potentials. Although the microenvironment significantly affected composition of the RAF communities in both plant species, the effect was greater in the case of C. epigejos RAF communities than in that of S. caprea RAF communities. The presence of S. caprea also significantly decreased AM fungal abundance in soil as well as AM colonization and richness of AM fungi in C. epigejos roots. Changes observed in the abundance and community composition of AM fungi might constitute an important factor in transition from AM-dominated to EcM-dominated vegetation during succession.

Cross-Cultural Variations in the Phenomenological Experience of Depression: I. Word Association Studies

ERIC Educational Resources Information Center

Tanaka-Matsumi, Junto; Marsella, Anthony J.

1976-01-01

Results indicate that nature plays a significant role in the emotional experience of the Japanese by providing concrete images which render impersonal ways of expressing feelings and emotions. (Author/AM)

Native arbuscular mycorrhizal symbiosis alters foliar bacterial community composition.

PubMed

Poosakkannu, Anbu; Nissinen, Riitta; Kytöviita, Minna-Maarit

2017-11-01

The effects of arbuscular mycorrhizal (AM) fungi on plant-associated microbes are poorly known. We tested the hypothesis that colonization by an AM fungus affects microbial species richness and microbial community composition of host plant tissues. We grew the grass, Deschampsia flexuosa in a greenhouse with or without the native AM fungus, Claroideoglomus etunicatum. We divided clonally produced tillers into two parts: one inoculated with AM fungus spores and one without AM fungus inoculation (non-mycorrhizal, NM). We characterized bacterial (16S rRNA gene) and fungal communities (internal transcribed spacer region) in surface-sterilized leaf and root plant compartments. AM fungus inoculation did not affect microbial species richness or diversity indices in leaves or roots, but the AM fungus inoculation significantly affected bacterial community composition in leaves. A total of three OTUs in leaves belonging to the phylum Firmicutes positively responded to the presence of the AM fungus in roots. Another six OTUs belonging to the Proteobacteria (Alpha, Beta, and Gamma) and Bacteroidetes were significantly more abundant in NM plants when compared to AM fungus-inoculated plants. Further, there was a significant correlation between plant dry weight and leaf microbial community compositional shift. Also, there was a significant correlation between leaf bacterial community compositional shift and foliar nitrogen content changes due to AM fungus inoculation. The results suggest that AM fungus colonization in roots has a profound effect on plant physiology that is reflected in leaf bacterial community composition.

Opening a Can of wERMS: Texas A&M University's Experiences in Implementing Two Electronic Resource Management Systems

ERIC Educational Resources Information Center

Hartnett, Eric; Price, Apryl; Smith, Jane; Barrett, Michael

2010-01-01

Over the past few years, Texas A&M University (TAMU) has searched for a way to administer its electronic subscriptions as well as the electronic subscriptions shared among the TAMU System. In this article, we address our attempts to implement an effective electronic resource management system (ERMS), both for subscriptions on the main campus…

Oxygen fugacity control in piston-cylinder experiments: a re-evaluation

NASA Astrophysics Data System (ADS)

Jakobsson, Sigurdur; Blundy, Jon; Moore, Gordon

2014-06-01

Jakobsson (Contrib Miner Petrol 164(3):397-407, 2012) investigated a double capsule assembly for use in piston-cylinder experiments that would allow hydrous, high-temperature, and high-pressure experiments to be conducted under controlled oxygen fugacity conditions. Using a platinum outer capsule containing a metal oxide oxygen buffer (Ni-NiO or Co-CoO) and H2O, with an inner gold-palladium capsule containing hydrous melt, this study was able to compare the oxygen fugacity imposed by the outer capsule oxygen buffer with an oxygen fugacity estimated by the AuPdFe ternary system calibrated by Barr and Grove (Contrib Miner Petrol 160(5):631-643, 2010). H2O loss or gain, as well as iron loss to the capsule walls and carbon contamination, is often observed in piston-cylinder experiments and often go unexplained. Only a few have attempted to actually quantify various aspects of these changes (Brooker et al. in Am Miner 83(9-10):985-994, 1998; Truckenbrodt and Johannes in Am Miner 84:1333-1335, 1999). It was one of the goals of Jakobsson (Contrib Miner Petrol 164(3):397-407, 2012) to address these issues by using and testing the AuPdFe solution model of Barr and Grove (Contrib Miner Petrol 160(5):631-643, 2010), as well as to constrain the oxygen fugacity of the inner capsule. The oxygen fugacities of the analyzed melts were assumed to be equal to those of the solid Ni-NiO and Co-CoO buffers, which is incorrect since the melts are all undersaturated in H2O and the oxygen fugacities should therefore be lower than that of the buffer by 2 log.

In situ measurement and source apportionment of aerosols in the Kathmandu valley, Nepal, April 2015.

NASA Astrophysics Data System (ADS)

DeCarlo, P. F.; Werden, B.; Goetz, J. D.; Giordano, M.; Bhave, P.; Jayarathne, T. S.; Stockwell, C.; Christian, T. J.; Nadler, W.; Panday, A. K.; Yokelson, R. J.; Stone, E. A.

2017-12-01

The Kathmandu Valley in Nepal is home to over 2.5 Million people, and is one of the fastest growing metropolitan areas in South Asia. It is subject to extreme pollution events due to numerous unregulated localized pollution sources and regional transport from the Indo-Gangetic Plain (IGP). Over 10% of Nepali fatalities are from lung disorders, making it the most common cause of death in the country. Previous field work has studied gas species, wintertime VOCs and PM in the valley. The Nepal Ambient Measurement and Site Testing Experiment [NAMaSTE] is the first deployment of a High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS) in Nepal and allows for a more comprehensive analysis of aerosol species and their source contributions. Ambient measurements for the NAMaSTE campaign were made in Bode, 8 km east of Kathmandu. Intensive measurements were made in April 2015, but cut short by the 2015 Gorka earthquake. HR-ToF-AMS measurements provided detailed chemical composition information on particulate matter in the valley. Ancillary measurements of chemical species CO, CO2, CH4, H2O, O3, NOx, BC and PM were carried out and compared to AMS data and meteorological parameters. AMS species show a clear diurnal pattern, with extremely elevated concentrations in the morning, with a wind shift to westerly in the afternoon. PMF was performed on the ambient data set, and mass spectral data was compared to source mass spectra generated from emission testing of various local sources measured during the campaign. The mean concentration of PM2.5 was 83 ± 45 µg/m3, which is above the 24 hour WHO exposure threshold of 25 µg/m3 and annual continous exposure limit of 10 µg/m3­­. Localized sources of anthropogenic emissions such as garbage burning, coal for brick kilns, dung and biomass burning for cooking and agriculture are likely sources of elevated pollutant emissions. Unmitigated burning of trash and biomass coupled with irregular fuels are a major source of pollutant species and aerosols in the undeveloped world.

Heat transfer characteristics of building walls using phase change material

NASA Astrophysics Data System (ADS)

Irsyad, M.; Pasek, A. D.; Indartono, Y. S.; Pratomo, A. W.

2017-03-01

Minimizing energy consumption in air conditioning system can be done with reducing the cooling load in a room. Heat from solar radiation which passes through the wall increases the cooling load. Utilization of phase change material on walls is expected to decrease the heat rate by storing energy when the phase change process takes place. The stored energy is released when the ambient temperature is low. Temperature differences at noon and evening can be utilized as discharging and charging cycles. This study examines the characteristics of heat transfer in walls using phase change material (PCM) in the form of encapsulation and using the sleeve as well. Heat transfer of bricks containing encapsulated PCM, tested the storage and released the heat on the walls of the building models were evaluated in this study. Experiments of heat transfer on brick consist of time that is needed for heat transfer and thermal conductivity test as well. Experiments were conducted on a wall coated by PCM which was exposed on a day and night cycle to analyze the heat storage and heat release. PCM used in these experiments was coconut oil. The measured parameter is the temperature at some points in the brick, walls and ambient temperature as well. The results showed that the use of encapsulation on an empty brick can increase the time for thermal heat transfer. Thermal conductivity values of a brick containing encapsulated PCM was lower than hollow bricks, where each value was 1.3 W/m.K and 1.6 W/m.K. While the process of heat absorption takes place from 7:00 am to 06:00 pm, and the release of heat runs from 10:00 pm to 7:00 am. The use of this PCM layer can reduce the surface temperature of the walls of an average of 2°C and slows the heat into the room.

Interactions between biochar and mycorrhizal fungi in a water-stressed agricultural soil.

PubMed

Mickan, Bede S; Abbott, Lynette K; Stefanova, Katia; Solaiman, Zakaria M

2016-08-01

Biochar may alleviate plant water stress in association with arbuscular mycorrhizal (AM) fungi but research has not been conclusive. Therefore, a glasshouse experiment was conducted to understand how interactions between AM fungi and plants respond to biochar application under water-stressed conditions. A twin chamber pot system was used to determine whether a woody biochar increased root colonisation by a natural AM fungal population in a pasture soil ('field' chamber) and whether this was associated with increased growth of extraradical AM fungal hyphae detected by plants growing in an adjacent ('bait') chamber containing irradiated soil. The two chambers were separated by a mesh that excluded roots. Subterranean clover was grown with and without water stress and harvested after 35, 49 and 63 days from each chamber. When biochar was applied to the field chamber under water-stressed conditions, shoot mass increased in parallel with mycorrhizal colonisation, extraradical hyphal length and shoot phosphorus concentration. AM fungal colonisation of roots in the bait chamber indicated an increase in extraradical mycorrhizal hyphae in the field chamber. Biochar had little effect on AM fungi or plant growth under well-watered conditions. The biochar-induced increase in mycorrhizal colonisation was associated with increased growth of extraradical AM fungal hyphae in the pasture soil under water-stressed conditions.

In Vitro and In Vivo Investigation of the Potential of Amorphous Microporous Silica as a Protein Delivery Vehicle

PubMed Central

Vanmellaert, Lieve; Vermaelen, Peter; Deroose, Christophe M.; Naert, Ignace; Cardoso, Marcio Vivan; Martens, Johan A.

2013-01-01

Delivering growth factors (GFs) at bone/implant interface needs to be optimized to achieve faster osseointegration. Amorphous microporous silica (AMS) has a potential to be used as a carrier and delivery platform for GFs. In this work, adsorption (loading) and release (delivery) mechanism of a model protein, bovine serum albumin (BSA), from AMS was investigated in vitro as well as in vivo. In general, strong BSA adsorption to AMS was observed. The interaction was stronger at lower pH owing to favorable electrostatic interaction. In vitro evaluation of BSA release revealed a peculiar release profile, involving a burst release followed by a 6 h period without appreciable BSA release and a further slower release later. Experimental data supporting this observation are discussed. Apart from understanding protein/biomaterial (BSA/AMS) interaction, determination of in vivo protein release is an essential aspect of the evaluation of a protein delivery system. In this regard micropositron emission tomography (μ-PET) was used in an exploratory experiment to determine in vivo BSA release profile from AMS. Results suggest stronger in vivo retention of BSA when adsorbed on AMS. This study highlights the possible use of AMS as a controlled protein delivery platform which may facilitate osseointegration. PMID:23991413

Measurements of Size Resolved Organic Particulate Mass Using An On-line Aerosol Mass Spectrometer (ams) Laboratory Validation; Analysis Tool Development; and Interpretation of Field Data

NASA Astrophysics Data System (ADS)

Alfarra, M. R.; Coe, H.; Allan, J. D.; Bower, K. N.; Garforth, A. A.; Canagaratna, M.; Worsnop, D.

The aerosol mass spectrometer (AMS) is a quantitative instrument designed to deliver real-time size resolved chemical composition of the volatile and semi volatile aerosol fractions. The AMS response to a wide range of organic compounds has been exper- imentally characterized, and has been shown to compare well with standard libraries of 70 eV electron impact ionization mass spectra. These results will be presented. Due to the scanning nature of the quadrupole mass spectrometer, the AMS provides averaged composition of ensemble of particles rather than single particle composi- tion. However, the mass spectra measured by AMS are reproducible and similar to those of standard libraries so analysis tools can be developed on large mass spectral libraries that can provide chemical composition information about the type of organic compounds in the aerosol. One such tool is presented and compared with laboratory measurements of single species and mixed component organic particles by the AMS. We will then discuss the applicability of these tools to interpreting field AMS data ob- tained in a range of experiments at different sites in the UK and Canada. The data will be combined with other measurements to show the behaviour of the organic aerosol fraction in urban and sub-urban environments.

A&M. Hot liquid waste treatment building (TAN616). Camera facing east. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Hot liquid waste treatment building (TAN-616). Camera facing east. Showing west facades of structure. Photographer: Ron Paarmann. Date: September 22, 1997. INEEL negative no. HD-20-1-1 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Recent advances in AM OLED technologies for application to aerospace and military systems

NASA Astrophysics Data System (ADS)

Sarma, Kalluri R.; Roush, Jerry; Chanley, Charles

2012-06-01

While initial AM OLED products have been introduced in the market about a decade ago, truly successful commercialization of OLEDs has started only a couple of years ago, by Samsung Mobile Display (SMD), with small high performance displays for smart phone applications. This success by Samsung has catalyzed significant interest in AM OLED technology advancement and commercialization by other display manufacturers. Currently, significant manufacturing capacity for AM OLED displays is being established by the industry to serve the growing demand for these displays. The current development in the AM OLED industry are now focused on the development and commercialization of medium size (~10") AM OLED panels for Tablet PC applications and large size (~55") panels for TV applications. This significant progress in commercialization of AM OLED technology is enabled by major advances in various enabling technologies that include TFT backplanes, OLED materials and device structures and manufacturing know-how. In this paper we will discuss these recent advances, particularly as they relate to supporting high performance applications such as aerospace and military systems, and then discuss the results of the OLED testing for aerospace applications.

KSC-2011-2200

NASA Image and Video Library

2011-03-10

CAPE CANAVERAL, Fla. -- In the Space Station Processing Facility's conference room at NASA's Kennedy Space Center in Florida, Ken Bollweg, Alpha Magnetic Spectrometer-2 (AMS) deputy project manager, talks to media about the particle physics detector. AMS is designed to operate as an external experiment on the International Space Station. It will use the unique environment of space to study the universe and its origin by searching for dark matter. AMS-2 will fly to the station aboard space shuttle Endeavour's STS-134 mission targeted to launch April 19 at 7:48 p.m. EDT. For more information visit, www.nasa.gov/mission_pages/shuttle/shuttlemissions/sts134/index.html. Photo credit: NASA/Glenn Benson

AmI in good care? Developing design principles for ambient intelligent domotics for elderly.

PubMed

Meulendijk, Michiel; Van De Wijngaert, Lidwien; Brinkkemper, Sjaak; Leenstra, Herbert

2011-03-01

The combination of ambient intelligence (AmI) and domotics has the potential to respond to elderly people's desire to live independent from extensive forms of care. Their slow adoption of technological aids shows reluctance, though. This article investigates their motivations to adopt ambient intelligent domotics, and proposes design principles specifically based on their preferences and experiences. Respondents appeared to be more acceptive of tangible problems they expected with AmI domotics than intangible ones. In addition, their opinions seemed to be profoundly influenced by the way they perceived their psychological quality of life, while their physical conditions did not seem to have noticeable impacts.

The subjectively perceived quality of postgraduate medical training in integrative medicine within the public healthcare systems of Germany and Switzerland: the example of anthroposophic hospitals

PubMed Central

2014-01-01

Background Integrative medicine (IM) integrates evidence-based Complementary and Alternative Medicine (CAM) with conventional medicine (CON). Medical schools offer basic CAM electives but in postgraduate medical training (PGMT) little has been done for the integration of CAM. An exception to this is anthroposophic medicine (AM), a western form of CAM based on CON, offering an individualized holistic IM approach. AM hospitals are part of the public healthcare systems in Germany and Switzerland and train AM in PGMT. We performed the first quality evaluation of the subjectively perceived quality of this PGMT. Methods An anonymous full survey of all 214 trainers (TR) and 240 trainees (TE) in all 15 AM hospitals in Germany and Switzerland, using the ETHZ questionnaire for annual national PGMT assessments in Switzerland (CH) and Germany (D), complemented by a module for AM. Data analysis included Cronbach’s alpha to assess internal consistency questionnaire scales, 2-tailed Pearson correlation of specific quality dimensions of PGMT and department size, 2-tailed Wilcoxon Matched-Pair test for dependent variables and 2-tailed Mann–Whitney U-test for independent variables to calculate group differences. The level of significance was set at p < 0.05. Results Return rates were: D: TE 89/215 (41.39%), TR 78/184 (42.39%); CH: TE 19/25 (76%), TR 22/30 (73.33%). Cronbach’s alpha values for TE scales were >0.8 or >0.9, and >0.7 to >0.5 for TR scales. Swiss hospitals surpassed German ones significantly in Global Satisfaction with AM (TR and TE); Clinical Competency training in CON (TE) and AM (TE, TR), Error Management, Culture of Decision Making, Evidence-based Medicine, and Clinical Competency in internal medicine CON and AM (TE). When the comparison was restricted to departments of comparable size, differences remained significant for Clinical Competencies in AM (TE, TR), and Culture of Decision Making (TE). CON received better grades than AM in Global Satisfaction and Clinical Competency. Quality of PGMT depended on department size, working conditions and structural training features. Conclusion The lower quality of PGMT in German hospitals can be attributed to larger departments, more difficult working conditions, and less favorable structural features for PGMT in AM, possibly also in relation to increased financial pressure. PMID:24934998

The subjectively perceived quality of postgraduate medical training in integrative medicine within the public healthcare systems of Germany and Switzerland: the example of anthroposophic hospitals.

PubMed

Heusser, Peter; Eberhard, Sabine; Berger, Bettina; Weinzirl, Johannes; Orlow, Pascale

2014-06-16

Integrative medicine (IM) integrates evidence-based Complementary and Alternative Medicine (CAM) with conventional medicine (CON). Medical schools offer basic CAM electives but in postgraduate medical training (PGMT) little has been done for the integration of CAM. An exception to this is anthroposophic medicine (AM), a western form of CAM based on CON, offering an individualized holistic IM approach. AM hospitals are part of the public healthcare systems in Germany and Switzerland and train AM in PGMT. We performed the first quality evaluation of the subjectively perceived quality of this PGMT. An anonymous full survey of all 214 trainers (TR) and 240 trainees (TE) in all 15 AM hospitals in Germany and Switzerland, using the ETHZ questionnaire for annual national PGMT assessments in Switzerland (CH) and Germany (D), complemented by a module for AM. Data analysis included Cronbach's alpha to assess internal consistency questionnaire scales, 2-tailed Pearson correlation of specific quality dimensions of PGMT and department size, 2-tailed Wilcoxon Matched-Pair test for dependent variables and 2-tailed Mann-Whitney U-test for independent variables to calculate group differences. The level of significance was set at p < 0.05. Return rates were: D: TE 89/215 (41.39%), TR 78/184 (42.39%); CH: TE 19/25 (76%), TR 22/30 (73.33%). Cronbach's alpha values for TE scales were >0.8 or >0.9, and >0.7 to >0.5 for TR scales. Swiss hospitals surpassed German ones significantly in Global Satisfaction with AM (TR and TE); Clinical Competency training in CON (TE) and AM (TE, TR), Error Management, Culture of Decision Making, Evidence-based Medicine, and Clinical Competency in internal medicine CON and AM (TE). When the comparison was restricted to departments of comparable size, differences remained significant for Clinical Competencies in AM (TE, TR), and Culture of Decision Making (TE). CON received better grades than AM in Global Satisfaction and Clinical Competency. Quality of PGMT depended on department size, working conditions and structural training features. The lower quality of PGMT in German hospitals can be attributed to larger departments, more difficult working conditions, and less favorable structural features for PGMT in AM, possibly also in relation to increased financial pressure.

Through the Glass Lightly.

ERIC Educational Resources Information Center

Wooddell, Glenn

1982-01-01

Recounts teaching experiences of a junior high school music teacher and his attempt to organize his experiences meaningfully. The discussion covers dimensions of student-teacher relationships, the importance of musicality, and the distinction between music training and music education. (AM)

Functions of Autobiographical Memory in Younger and Older Adults.

PubMed

Vranić, Andrea; Jelić, Margareta; Tonković, Mirjana

2018-01-01

Functional approach to autobiographical memory (AM) posits its three broad functions: directive, self, and social. Although these functions are probably universal, life stage and gender variations are expected. This research builds on previous studies investigating the validity of Thinking About Life Experiences Questionnaire (TALE; Bluck and Alea, 2011). A sample of 365 adults (56% female, mean age 43.3 years), divided in 2 age cohorts (young: 18-45 years, old: 46-90 years), used TALE, to rate their tendency of using AM for three different purposes, and measures of self-concept clarity, attachment in close relationships and time perspective. Confirmatory factor analysis of TALE confirmed the tripartite model of AM functions and further analysis showed partial factorial equivalence across age and gender groups. Young tend to use AM more for directing future behavior and social-bonding, while no age differences were found in the use of AM to serve self-function. As for gender variations, women tend to use AM more for directing their behavior, while no other gender differences in the use of AM were found. TALE showed good internal consistency and convergent validity of the three subscales. The theory-driven hypotheses that individuals with low self-concept clarity would use AM more often to serve a self-function, those with higher levels of attachment anxiety would use AM more often to serve a social function, and those past-oriented would use memory more often for directive purpose, were all confirmed. Also confirmed was the notion of Past Negative Orientation to be more related to the directive use of AM than Past Positive Time Orientation. Limitations and future directions are discussed.

Functions of Autobiographical Memory in Younger and Older Adults

PubMed Central

Vranić, Andrea; Jelić, Margareta; Tonković, Mirjana

2018-01-01

Functional approach to autobiographical memory (AM) posits its three broad functions: directive, self, and social. Although these functions are probably universal, life stage and gender variations are expected. This research builds on previous studies investigating the validity of Thinking About Life Experiences Questionnaire (TALE; Bluck and Alea, 2011). A sample of 365 adults (56% female, mean age 43.3 years), divided in 2 age cohorts (young: 18–45 years, old: 46–90 years), used TALE, to rate their tendency of using AM for three different purposes, and measures of self-concept clarity, attachment in close relationships and time perspective. Confirmatory factor analysis of TALE confirmed the tripartite model of AM functions and further analysis showed partial factorial equivalence across age and gender groups. Young tend to use AM more for directing future behavior and social-bonding, while no age differences were found in the use of AM to serve self-function. As for gender variations, women tend to use AM more for directing their behavior, while no other gender differences in the use of AM were found. TALE showed good internal consistency and convergent validity of the three subscales. The theory-driven hypotheses that individuals with low self-concept clarity would use AM more often to serve a self-function, those with higher levels of attachment anxiety would use AM more often to serve a social function, and those past-oriented would use memory more often for directive purpose, were all confirmed. Also confirmed was the notion of Past Negative Orientation to be more related to the directive use of AM than Past Positive Time Orientation. Limitations and future directions are discussed. PMID:29599732

Ultra-sensitive magnetic microscopy with an atomic magnetometer and flux guides

NASA Astrophysics Data System (ADS)

Kim, Young Jin; Savukov, Igor

Many applications in neuroscience, biomedical research, and material science require high-sensitivity, high-resolution magnetometry. In order to meet this need we recently combined a cm-size spin-exchange relaxation-free Atomic Magnetometer (AM) with a flux guide (FG) to produce ultra-sensitive FG-AM magnetic microscopy. The FG serves to transmit the target magnetic flux to the AM thus enhancing both the sensitivity and resolution to tiny magnetic objects. In this talk, we will describe existing and next generation FG-AM devices and present experimental and numerical tests of its sensitivity and resolution. We demonstrate that an optimized FG-AM has sufficient resolution and sensitivity for the detection of a small number of neurons, which would be an important milestone in neuroscience. In addition, as a demonstration of one possible application of the FG-AM device, we conducted high-resolution magnetic imaging of micron-size magnetic particles. We will show that the device can produce clear microscopic magnetic image of 10 μm-size magnetic particles.

A&M. Outdoor turntable. Workings and design exposed during demolition. View ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Outdoor turntable. Workings and design exposed during demolition. View between two of the four rails of the track. Note motor and electrical conduit. Date: February 3, 2003. INEEL negative no. HD-37-1-1 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Predicting Naming Latencies with an Analogical Model

ERIC Educational Resources Information Center

Chandler, Steve

2008-01-01

Skousen's (1989, Analogical modeling of language, Kluwer Academic Publishers, Dordrecht) Analogical Model (AM) predicts behavior such as spelling pronunciation by comparing the characteristics of a test item (a given input word) to those of individual exemplars in a data set of previously encountered items. While AM and other exemplar-based models…

Environmental Technology Verification Report for Abraxis Ecologenia® Ethynylestradiol (EE2) Microplate Enzyme-Linked Immunosorbent Assay (ELISA) Test Kits

EPA Science Inventory

The EPA's National Risk Management Research Laboratory (NRMRL) and its verification organization partner, Battelle, operate the Advanced Monitoring Systems (AMS) Center under ETV. The AMS Center recently evaluated the performance of the Abraxis Ecologenia Ethynylestradiol (EE2) ...

A&M. Hot liquid waste treatment building (TAN616). Camera facing northeast. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Hot liquid waste treatment building (TAN-616). Camera facing northeast. South wall with oblique views of west sides of structure. Photographer: Ron Paarmann. Date: September 22, 1997. INEEL negative no. HD-20-1-2 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

A&M. Hot liquid waste treatment building (TAN616). Camera facing north. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. Hot liquid waste treatment building (TAN-616). Camera facing north. Detail of personnel entrance door, stoop, and stairway. Photographer: Ron Paarmann. Date: September 22, 1997. INEEL negative no. HD-20-2-1 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

7 CFR 91.101 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Definitions. 91.101 Section 91.101 Agriculture... Officially Tested By AMS § 91.101 Definitions. Words used in the regulations in this part in the singular... United States of America to another country in the course of trade. Laboratory. An AMS Science and...

A&M. TAN607. Southern sections added in expansion project of 1957. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. TAN-607. Southern sections added in expansion project of 1957. Camera facing northwest. Concrete decontamination section on left end. Photographer: Jack L. Anderson. Date: October 23, 1957. INEEL negative no. 57-5337 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Development of a modular test system for the silicon sensor R&D of the ATLAS Upgrade

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, H.; Benoit, M.; Chen, H.

High Voltage CMOS sensors are a promising technology for tracking detectors in collider experiments. Extensive R&D studies are being carried out by the ATLAS Collaboration for a possible use of HV-CMOS in the High Luminosity LHC upgrade of the Inner Tracker detector. CaRIBOu (Control and Readout Itk BOard) is a modular test system developed to test Silicon based detectors. It currently includes five custom designed boards, a Xilinx ZC706 development board, FELIX (Front-End LInk eXchange) PCIe card and a host computer. A software program has been developed in Python to control the CaRIBOu hardware. CaRIBOu has been used in themore » testbeam of the HV-CMOS sensor AMS180v4 at CERN. Preliminary results have shown that the test system is very versatile. In conclusion, further development is ongoing to adapt to different sensors, and to make it available to various lab test stands.« less

Development of a modular test system for the silicon sensor R&D of the ATLAS Upgrade

DOE PAGES

Liu, H.; Benoit, M.; Chen, H.; ...

2017-01-11

High Voltage CMOS sensors are a promising technology for tracking detectors in collider experiments. Extensive R&D studies are being carried out by the ATLAS Collaboration for a possible use of HV-CMOS in the High Luminosity LHC upgrade of the Inner Tracker detector. CaRIBOu (Control and Readout Itk BOard) is a modular test system developed to test Silicon based detectors. It currently includes five custom designed boards, a Xilinx ZC706 development board, FELIX (Front-End LInk eXchange) PCIe card and a host computer. A software program has been developed in Python to control the CaRIBOu hardware. CaRIBOu has been used in themore » testbeam of the HV-CMOS sensor AMS180v4 at CERN. Preliminary results have shown that the test system is very versatile. In conclusion, further development is ongoing to adapt to different sensors, and to make it available to various lab test stands.« less

Risk Assessment of Physiological Effects of Atmospheric Composition and Pressure in Constellation Vehicles

NASA Technical Reports Server (NTRS)

Scheuring, Richard A.; Conkin, Johnny; Jones, Jeffrey A.; Gernhardt, Michael L.

2007-01-01

To reduce denitrogenation time to prevent decompression sickness to support frequent extravehicular activities on the Moon, and to limit the risk of fire, a hypobaric (P(sub B) = 414 mmHg) and mildly hypoxic (ppO2 = 132 mmHg, 32% O2 - 68% N2) living environment is being considered during lunar missions for the Crew Exploration Vehicle (CEV) and Lunar Surface Access Module (LSAM). If the vehicular ppO2 is acutely changed from 145-178 mmHg at standard vehicular operating pressure to less than 125 mmHg at desired lunar surface outpost operating pressures, there is the possibility that some crewmembers may develop symptoms of Acute Mountain Sickness (AMS). The signs and symptoms of AMS (headache plus nausea, dizziness, fatigue, or sleeplessness), could impact crew health and performance on lunar surface missions. Methods: An exhaustive literature review on the topic of the physiological effects of reduced ppO2 and absolute pressure as may contribute to the development of hypoxia and altitude symptoms or AMS. The results of the nine most rigorous studies were collated, analyzed and contents on the physiological concerns associated with hypobaric operations, AMS and hypoxia symptoms summarized. Results: Although space vehicles have operated in hypobaric conditions previously, they have not operated in a mildly hypoxic ppO2. There is evidence for an absolute pressure effect per se on AMS, such that the higher the altitude for a given hypoxic alveolar O2 partial pressure (P(sub A)O2), the greater the likelihood of an AMS response. About 25% of adults are likely to experience mild AMS near 2,000 m (xxx mmHg) altitude following a rapid ascent from sea level while breathing air (6,500 feet, acute (P(sub A)O2) = 75 mmHg). The operational experience with the Shuttle staged denitrogenation protocol at 528 mmHg (3,048 m) while breathing 26.5% O2 (acute (P(sub A)O2) = 85 mmHg) in astronauts adapting to microgravity suggests a similar likely experience in the proposed CEV environment. Conclusions: We feel that the slightly elevated risk of AMS with the recommended exploration atmospheric parameters is offset by the DCS risk reduction and improved operational efficiency offered by the hypobaric lunar surface vehicular pressure. We believe the risk of mild AMS is greater given a (P(sub A)O2) of 77 mmHg at 4,876 m altitude while breathing 32% O2 than at 1,828 m altitude while breathing 21% O2. Only susceptible astronauts would develop mild and transient AMS with prolonged exposure to 414 mmHg (4,876 m) while breathing 32% O2 (acute (P(sub A)O2) = 77 mmHg). So the following may be employed for operational risk reduction: 1) develop procedures to increase P(sub B) as needed in the CEV, and use a gradual or staged reduction in cabin pressure during lunar outbound; 2) train crews for symptoms of hypoxia, to allow early recognition and consider pre-adaptation of crews to a hypoxic environment prior to launch, 3) consider prophylactic acetazolamide for acute pressure changes and be prepared to treat any AMS associated symptoms early with both carbonic anhydrase inhibitors and supplemental oxygen.

Immunoadjuvant Chemotherapy of Visceral Leishmaniasis in Hamsters Using Amphotericin B-Encapsulated Nanoemulsion Template-Based Chitosan Nanocapsules

PubMed Central

Asthana, Shalini; Jaiswal, Anil K.; Gupta, Pramod K.; Pawar, Vivek K.; Dube, Anuradha

2013-01-01

The accessible treatment options for life-threatening neglected visceral leishmaniasis (VL) disease have problems with efficacy, stability, adverse effects, and cost, making treatment a complex issue. Here we formulated nanometric amphotericin B (AmB)-encapsulated chitosan nanocapsules (CNC-AmB) using a polymer deposition technique mediated by nanoemulsion template fabrication. CNC-AmB exhibited good steric stability in vitro, where the chitosan content was found to be efficient at preventing destabilization in the presence of protein and Ca2+. A toxicity study on the model cell line J774A and erythrocytes revealed that CNC-AmB was less toxic than commercialized AmB formulations such as Fungizone and AmBisome. The results of in vitro (macrophage-amastigote system; 50% inhibitory concentration [IC50], 0.19 ± 0.04 μg AmB/ml) and in vivo (Leishmania donovani-infected hamsters; 86.1% ± 2.08% parasite inhibition) experiments in conjunction with effective internalization by macrophages illustrated the efficacy of CNC-AmB at augmenting antileishmanial properties. Quantitative mRNA analysis by real-time PCR (RT-PCR) showed that the improved effect was synergized with the upregulation of tumor necrosis factor alpha (TNF-α), interleukin-12 (IL-12), and inducible nitric oxide synthase and with the downregulation of transforming growth factor β (TGF-β), IL-10, and IL-4. These research findings suggest that a cost-effective CNC-AmB immunoadjuvant chemotherapeutic delivery system could be a viable alternative to the current high-cost commercial lipid-based formulations. PMID:23357762

Alcohol mixed with energy drink: Use may be a consequence of heavy drinking.

PubMed

Rossheim, Matthew E; Thombs, Dennis L; Weiler, Robert M; Barry, Adam E; Suzuki, Sumihiro; Walters, Scott T; Barnett, Tracey E; Paxton, Raheem J; Pealer, Lisa N; Cannell, Brad

2016-06-01

In recent years, studies have indicated that consumers of alcohol mixed with energy drink (AmED) are more likely to drink heavily and experience more negative consequences than consumers who avoid these beverages. Although researchers have identified a number of plausible hypotheses that explain how alcohol-energy drink co-ingestion could cause greater alcohol consumption, there has been no postulation about reverse causal relations. This paper identifies several plausible hypotheses for the observed associations between AmED consumption and greater alcohol consumption, and provides initial evidence for one such hypothesis suggesting that heavy drinking may be a determinant of AmED use. Data collected from 511bar patrons were used to examine the plausibility of one of the proposed hypotheses, i.e., AmED is an artifact of heavy drinking. Associations between the consumption of an assortment of alcoholic beverage types and total alcohol consumption were examined at the event-level, to assess whether AmED is uniquely related with greater alcohol consumption. Increased alcohol consumption was associated with greater odds of consuming most alcoholic beverage types; this association was not unique to AmED. Results support the overlooked hypothesis that AmED use is an artifact of heavy drinking. Thus, AmED consumption may be a consequence or marker of heavier drinking. Much of the existing research on alcoholic beverage types is limited in its ability to implicate any specific type of drink, including AmED, as a cause of increased alcohol consumption and related harm. More rigorous study designs are needed to examine causal relationships. Copyright © 2016 Elsevier Ltd. All rights reserved.

Competitive interactions are mediated in a sex-specific manner by arbuscular mycorrhiza in Antennaria dioica.

PubMed

Varga, S; Vega-Frutis, R; Kytöviita, M-M

2017-03-01

Plants usually interact with other plants, and the outcome of such interaction ranges from facilitation to competition depending on the identity of the plants, including their sexual expression. Arbuscular mycorrhizal (AM) fungi have been shown to modify competitive interactions in plants. However, few studies have evaluated how AM fungi influence plant intraspecific and interspecific interactions in dioecious species. The competitive abilities of female and male plants of Antennaria dioica were examined in a greenhouse experiment. Females and males were grown in the following competitive settings: (i) without competition, (ii) with intrasexual competition, (iii) with intersexual competition, and (iv) with interspecific competition by Hieracium pilosella - a plant with similar characteristics to A. dioica. Half of the pots were grown with Claroideoglomus claroideum, an AM fungus isolated from the same habitat as the plant material. We evaluated plant survival, growth, flowering phenology, and production of AM fungal structures. Plant survival was unaffected by competition or AM fungi. Competition and the presence of AM fungi reduced plant biomass. However, the sexes responded differently to the interaction between fungal and competition treatments. Both intra- and interspecific competition results were sex-specific, and in general, female performance was reduced by AM colonization. Plant competition or sex did not affect the intraradical structures, extraradical hyphae, or spore production of the AM fungus. These findings suggest that plant sexual differences affect fundamental processes such as competitive ability and symbiotic relationships with AM fungi. © 2016 German Botanical Society and The Royal Botanical Society of the Netherlands.

The stationary non-equilibrium plasma of cosmic-ray electrons and positrons

NASA Astrophysics Data System (ADS)

Tomaschitz, Roman

2016-06-01

The statistical properties of the two-component plasma of cosmic-ray electrons and positrons measured by the AMS-02 experiment on the International Space Station and the HESS array of imaging atmospheric Cherenkov telescopes are analyzed. Stationary non-equilibrium distributions defining the relativistic electron-positron plasma are derived semi-empirically by performing spectral fits to the flux data and reconstructing the spectral number densities of the electronic and positronic components in phase space. These distributions are relativistic power-law densities with exponential cutoff, admitting an extensive entropy variable and converging to the Maxwell-Boltzmann or Fermi-Dirac distributions in the non-relativistic limit. Cosmic-ray electrons and positrons constitute a classical (low-density high-temperature) plasma due to the low fugacity in the quantized partition function. The positron fraction is assembled from the flux densities inferred from least-squares fits to the electron and positron spectra and is subjected to test by comparing with the AMS-02 flux ratio measured in the GeV interval. The calculated positron fraction extends to TeV energies, predicting a broad spectral peak at about 1 TeV followed by exponential decay.

High-Temperature Creep Degradation of the AM1/NiAlPt/EBPVD YSZ System

NASA Astrophysics Data System (ADS)

Riallant, Fanny; Cormier, Jonathan; Longuet, Arnaud; Milhet, Xavier; Mendez, José

2014-01-01

The failure mechanisms of a NiAlPt/electron beam physical vapor deposition yttria-stabilized-zirconia thermal barrier coating system deposited on the AM1 single crystalline substrate have been investigated under pure creep conditions in the temperature range from 1273 K to 1373 K (1000 °C to 1100 °C) and for durations up to 1000 hours. Doubly tapered specimens were used allowing for the analysis of different stress states and different accumulated viscoplastic strains for a given creep condition. Under such experiments, two kinds of damage mechanisms were observed. Under low applied stress conditions ( i.e., long creep tests), microcracking is localized in the vicinity of the thermally grown oxide (TGO). Under high applied stress conditions, an unconventional failure mechanism at the substrate/bond coat interface is observed because of large creep strains and fast creep deformation, hence leading to a limited TGO growth. This unconventional failure mechanism is observed although the interfacial bond coat/top coat TGO thickening is accelerated by the mechanical applied stress beyond a given stress threshold.

Mitigation of High Altitude and Low Earth Orbit Radiation Effects on Microelectronics via Shielding or Error Detection and Correction Systems

NASA Technical Reports Server (NTRS)

Gupta, Kajal (Technical Monitor); Kirby, Kelvin

2004-01-01

The NASA Cooperative Agreement NAG4-210 was granted under the FY2000 Faculty Awards for Research (FAR) Program. The project was proposed to examine the effects of charged particles and neutrons on selected random access memory (RAM) technologies. The concept of the project was to add to the current knowledge of Single Event Effects (SEE) concerning RAM and explore the impact of selected forms of radiation on Error Detection and Correction Systems. The project was established as an extension of a previous FAR awarded to Prairie View A&M University (PVAMU), under the direction of Dr. Richard Wilkins as principal investigator. The NASA sponsored Center for Applied Radiation Research (CARR) at PVAMU developed an electronic test-bed to explore and quantify SEE on RAM from charged particles and neutrons. The test-bed was developed using 486DX microprocessor technology (PC-104) and a custom test board to mount RAM integrated circuits or other electronic devices. The test-bed had two configurations - a bench test version for laboratory experiments and a 400 Hz powered rack version for flight experiments. The objectives of this project were to: 1) Upgrade the Electronic Test-bed (ETB) to a Pentium configuration; 2) Accommodate more than only 8 Mbytes of RAM; 3) Explore Error Detection and Correction Systems for radiation effects; 4) Test modern RAM technologies in radiation environments.

Orally Administered DTPA Di-ethyl Ester for Decorporation of 241Am in dogs: Assessment of Safety and Efficacy in an Inhalation-Contamination Model

PubMed Central

Huckle, James E.; Sadgrove, Matthew P.; Pacyniak, Erik; Leed, Marina G. D.; Weber, Waylon M.; Doyle-Eisele, Melanie; Guilmette, Raymond A.; Agha, Bushra J.; Susick, Robert L.; Mumper, Russell J.; Jay, Michael

2016-01-01

Purpose Currently two injectable products of diethylenetriaminepentaacetic acid (DTPA) are U.S. Food and Drug Administration (FDA) approved for decorporation of 241Am, however, an oral product is considered more amenable in a mass casualty situation. The diethyl ester of DTPA, named C2E2, is being developed as an oral drug for treatment of internal radionuclide contamination. Materials and methods Single dose decorporation efficacy of C2E2 administered 24-hours post contamination was determined in beagle dogs using a 241Am nitrate inhalation contamination model. Single and multiple dose toxicity studies in beagle dogs were performed as part of an initial safety assessment program. In addition, the genotoxic potential of C2E2 was evaluated by the in vitro bacterial reverse mutation Ames test, mammalian cell chromosome aberration cytogenetic assay and an in vivo micronucleus test. Results Oral administration of C2E2 significantly increased 241Am elimination over untreated controls and significantly reduced the retention of 241Am in tissues, especially liver, kidney, lung and bone. Daily dosing of 200 mg/kg/day for 10 days was well tolerated in dogs. C2E2 was found to be neither mutagenic or clastogenic. Conclusions The di-ethyl ester of DTPA (C2E2) was shown to effectively enhance the elimination of 241Am after oral administration in a dog inhalation-contamination model and was well tolerated in toxicity studies. PMID:25912343

[The effect of the intratracheal administration of americium-241 on rat alveolar macrophages].

PubMed

Shopova, V; Sŭlovski, P; Dancheva, V

1996-01-01

In experiments in rats it was found that 241Am transitory decreases the total cell number and alveolar macrophage's percentage in bronchoalveolar lavage fluid (BALF): increases the macrophages size and nuclear size; and increases acid phosphatase and lactate dehydrogenase activities in BALF. It was suggested that 241Am causes and activation in the alveolar macrophages which probably appears as one of factors provoking lung injuries.

Precise measurement of cosmic ray fluxes with the AMS-02 experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vecchi, Manuela, E-mail: manuela.vecchi@ifsc.usp.br

2015-12-17

The AMS-02 detector is a large acceptance magnetic spectrometer operating onboard the International Space Station since May 2011. The main goals of the detector are the search for antimatter and dark matter in space, as well as the measurement of cosmic ray composition and flux. In this document we present precise measurements of cosmic ray positrons, electrons and protons, collected during the first 30 months of operations.

M-TeX and MIST Experiments Launched from Alaska

NASA Image and Video Library

2017-12-08

Caption: Composite shot of all four rockets for the M-TeX and MIST experiments is made up of 30 second exposures. The rocket salvo began at 4:13 a.m. EST, Jan. 26, 2015, from the Poker Flat Research Range, Alaska. Credit: NASA/Jamie Adkins More info: The Mesosphere-Lower Thermosphere Turbulence Experiment, or M-TeX, and the Mesospheric Inversion-layer Stratified Turbulence, or MIST, experiment were successfully conducted the morning of Jan. 26, 2015, from the Poker Flat Research Range, Alaska. The first M-Tex rocket, a NASA Terrier-Improved Malemute sounding rocket, was launched at 4:13 a.m. EST and was followed one-minute later by the first MIST experiment payload on a NASA Terrier-Improved Orion. The second M-TeX payload was launched at 4:46 a.m. EST and also was followed one minute later by the second MIST payload. Preliminary data show that all four payloads worked as planned and the trimethyl aluminum, or TMA, vapor trails were seen at the various land-based observation sites in Alaska. A fifth rocket carrying the Auroral Spatial Structures Probe remains ready on the launch pad. The launch window for this experiment runs through Jan. 27. NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Autobiographical memory and structural brain changes in chronic phase TBI.

PubMed

Esopenko, Carrie; Levine, Brian

2017-04-01

Traumatic brain injury (TBI) is associated with a range of neuropsychological deficits, including attention, memory, and executive functioning attributable to diffuse axonal injury (DAI) with accompanying focal frontal and temporal damage. Although the memory deficit of TBI has been well characterized with laboratory tests, comparatively little research has examined retrograde autobiographical memory (AM) at the chronic phase of TBI, with no prior studies of unselected patients drawn directly from hospital admissions for trauma. Moreover, little is known about the effects of TBI on canonical episodic and non-episodic (e.g., semantic) AM processes. In the present study, we assessed the effects of chronic-phase TBI on AM in patients with focal and DAI spanning the range of TBI severity. Patients and socioeconomic- and age-matched controls were administered the Autobiographical Interview (AI) (Levine, Svoboda, Hay, Winocur, & Moscovitch, 2002) a widely used method for dissociating episodic and semantic elements of AM, along with tests of neuropsychological and functional outcome. Measures of episodic and non-episodic AM were compared with regional brain volumes derived from high-resolution structural magnetic resonance imaging (MRI). Severe TBI (but not mild or moderate TBI) was associated with reduced recall of episodic autobiographical details and increased recall of non-episodic details relative to healthy comparison participants. There were no significant associations between AM performance and neuropsychological or functional outcome measures. Within the full TBI sample, autobiographical episodic memory was associated with reduced volume distributed across temporal, parietal, and prefrontal regions considered to be part of the brain's AM network. These results suggest that TBI-related distributed volume loss affects episodic autobiographical recollection. Copyright © 2017 Elsevier Ltd. All rights reserved.

Refined liquid smoke: a potential antilisterial additive to cold-smoked sockeye salmon (Oncorhynchus nerka).

PubMed

Montazeri, Naim; Himelbloom, Brian H; Oliveira, Alexandra C M; Leigh, Mary Beth; Crapo, Charles A

2013-05-01

Cold-smoked salmon (CSS) is a potentially hazardous ready-to-eat food product due to the high risk of contamination with Listeria monocytogenes and lack of a listericidal step. We investigated the antilisterial property of liquid smokes (LS) against Listeria innocua ATCC 33090 (surrogate to L. monocytogenes) as a potential supplement to vacuum-packaged CSS. A full-strength LS (Code 10-Poly), and three commercially refined fractions (AM-3, AM-10, and 1291) having less color and flavor (lower content of phenols and carbonyl-containing compounds) were tested. In vitro assays showed strong inhibition for all LS except for 1291. The CSS strips were surface coated with AM-3 and AM-10 at 1% LS (vol/wt) with an L-shaped glass rod and then inoculated with L. innocua at 3.5 log CFU/g, vacuum packaged, and stored at 4°C. The LS did not completely eliminate L. innocua but provided a 2-log reduction by day 14, with no growth up to 35 days of refrigerated storage. A simple difference sensory test by 180 untrained panelists showed the application of AM-3 did not significantly influence the overall sensorial quality of CSS. In essence, the application of the refined LS as an antilisterial additive to CSS is recommended.

Multiple disparities in adult mortality in relation to social and health care perspective: results from different data sources.

PubMed

Ranabhat, Chhabi Lal; Kim, Chun-Bae; Park, Myung-Bae; Acharaya, Sambhu

2017-08-08

Disparity in adult mortality (AM) with reference to social dynamics and health care has not been sufficiently examined. This study aimed to identify the gap in the understanding of AM in relation to religion, political stability, economic level, and universal health coverage (UHC). A cross-national study was performed with different sources of data, using the administrative record linkage theory. Data was created from the 2013 World Bank data catalogue by region, The Economist (Political instability index 2013), Stuckler David et al. (Universal health coverage, 2010), and religious categories of all UN country members. Descriptive statistics, a t-test, an ANOVA followed by a post hoc test, and a linear regression were used where applicable. The average AM rate for males and females was 0.20 ± 0.10 and 0.14 ± 0.10, respectively. There was high disparity of AM between countries with and without UHC and between groups with low and high income. UHC and political stability would significantly reduce AMR by >0.41 in both sexes and high economic status would reduce male AMR by 0.44, and female AMR by 0.70. It can be concluded that effective health care; UHC and political stability significantly reduce AM.

Design and Fabrication of an Elastomer Test Machine.

DTIC Science & Technology

1988-05-01

provided by the Army Materials Technology Laboratories, were tested with the ETM at U.C.N.W. RUBBER 15 TP14AX 15 NAT25A 15 SBR26 NBR 6 FIBREGLASS REINFORCED...stationary, tilted and rotational) are comparable with 0001 AM and 0001 AN samples. SAMPLE NBR 62 This is a matt black, rubber based sample described as a... RUBBER 0001 AM 0001 AN 0001 AE -6- POLYURETHANE ECP 1 S ECP 2 Morbay 2690 Budd 20 1080 (Polyester) ) Gallagher Corporation A8 (Polyester) ) All

A&M. TAN607 first floor plan for cold assembly area. Shows ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

A&M. TAN-607 first floor plan for cold assembly area. Shows special source vaults, X-ray room, instrument shops, and positions of large machines in component test laboratory. This drawing was re-drawn to show conditions in 1994. Ralph M. Parsons 902-3-ANP-607-A 100. Date of original: December 1952. Approved by INEEL Classification Office for public release. INEEL index code no. 034-060-00-693-106752 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

Engineering Oral and Parenteral Amorphous Amphotericin B Formulations against Experimental Trypanosoma cruzi Infections.

PubMed

Rolón, Miriam; Serrano, Dolores R; Lalatsa, Aikaterini; de Pablo, Esther; Torrado, Juan Jose; Ballesteros, Maria Paloma; Healy, Anne Marie; Vega, Celeste; Coronel, Cathia; Bolás-Fernández, Francisco; Dea-Ayuela, Maria Auxiliadora

2017-04-03

Chagas disease (CD) is a parasitic zoonosis endemic in most mainland countries of Central and South America affecting nearly 10 million people, with 100 million people at high risk of contracting the disease. Treatment is only effective if received at the early stages of the disease. Only two drugs (benznidazole and nifurtimox) have so far been marketed, and both share various limitations such as variable efficacy, many side effects, and long duration of treatment, thus reducing compliance. The in vitro and in vivo efficacy of poly-aggregated amphotericin B (AmB), encapsulated poly-aggregated AmB in albumin microspheres (AmB-AME), and dimeric AmB-sodium deoxycholate micelles (AmB-NaDC) was evaluated. Dimeric AmB-NaDC exhibited a promising selectivity index (SI = 3164) against amastigotes, which was much higher than those obtained for licensed drugs (benznidazole and nifurtimox). AmB-AME, but not AmB-NaDC, significantly reduced the parasitemia levels (3.6-fold) in comparison to the control group after parenteral administration at day 7 postinfection. However, the oral administration of AmB-NaDC (10-15 mg/kg/day for 10 days) resulted in a 75% reduction of parasitemia levels and prolonged the survival rate in 100% of the tested animals. Thus, the results presented here illustrate for the first time the oral efficacy of AmB in the treatment of trypanosomiasis. AmB-NaDC is an easily scalable, affordable formulation prepared from GRAS excipients, enabling treatment access worldwide, and therefore it can be regarded as a promising therapy for trypanosomiasis.

Arbuscular mycorrhizal communities in tropical forests are affected by host tree species and environment.

PubMed

Lovelock, Catherine E; Andersen, Kelly; Morton, Joseph B

2003-04-01

Arbuscular mycorrhizal (AM) fungi are mutualists with plant roots that are proposed to enhance plant community diversity. Models indicate that AM fungal communities could maintain plant diversity in forests if functionally different communities are spatially separated. In this study we assess the spatial and temporal distribution of the AM fungal community in a wet tropical rainforest in Costa Rica. We test whether distinct fungal communities correlate with variation in tree life history characteristics, with host tree species, and the relative importance of soil type, seasonality and rainfall. Host tree species differ in their associated AM fungal communities, but differences in the AM community between hosts could not be generalized over life history groupings of hosts. Changes in the relative abundance of a few common AM fungal species were the cause of differences in AM fungal communities for different host tree species instead of differences in the presence and absence of AM fungal species. Thus, AM fungal communities are spatially distinguishable in the forest, even though all species are widespread. Soil fertility ranging between 5 and 9 Mg/ha phosphorus did not affect composition of AM fungal communities, although sporulation was more abundant in lower fertility soils. Sampling soils over seasons revealed that some AM fungal species sporulate profusely in the dry season compared to the rainy season. On one host tree species sampled at two sites with vastly different rainfall, relative abundance of spores from Acaulospora was lower and that of Glomus was relatively higher at the site with lower and more seasonal rainfall.

Combined caffeine and bright light reduces dangerous driving in sleep-deprived healthy volunteers: a pilot cross-over randomised controlled trial.

PubMed

Hartley, S L; Barbot, F; Machou, M; Lejaille, M; Moreau, B; Vaugier, I; Lofaso, F; Quera-Salva, M A

2013-06-01

To explore the effects of caffeine and bright light therapy on simulated nighttime driving in sleep-deprived healthy volunteers. Twelve male healthy volunteers aged 20 to 50 years participated in a randomized cross-over study of simulated nighttime driving at a sleep laboratory, followed by recovery sleep with polysomnography at home. The volunteers received variable combinations of caffeine 200mg (C+), caffeine placebo (C-), bright light 10,000 lux (L+), and bright light placebo<50 lux (L-), in four sessions (C+L+, C+L-, C-L+, C-L-), in random order with a wash-out period of 7 days. Treatments were given at 1 a.m. and testing was performed at 1:30 a.m., 3 a.m., 4 a.m., and 6 a.m. Lane drifting was the primary outcome measure. Other measures were reaction times, self-rated fatigue, sleepiness and recovery sleep. Without treatment, lane drifting increased throughout the night, and objective and subjective vigilance declined. Paired comparisons showed that lane drifting was significantly worse at 6 a.m. and at 4 a.m. than at 1:30 a.m. There was a global treatment effect on lane drifting. Lane drifting at 6 a.m. was significantly decreased with C+L+ compared to C-L-. Bright light therapy combined with caffeine administered at 1 a.m. decreased lane drifting by healthy volunteers during simulated nighttime driving. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

Altered free radical metabolism in acute mountain sickness: implications for dynamic cerebral autoregulation and blood-brain barrier function.

PubMed

Bailey, D M; Evans, K A; James, P E; McEneny, J; Young, I S; Fall, L; Gutowski, M; Kewley, E; McCord, J M; Møller, Kirsten; Ainslie, P N

2009-01-15

We tested the hypothesis that dynamic cerebral autoregulation (CA) and blood-brain barrier (BBB) function would be compromised in acute mountain sickness (AMS) subsequent to a hypoxia-mediated alteration in systemic free radical metabolism. Eighteen male lowlanders were examined in normoxia (21% O(2)) and following 6 h passive exposure to hypoxia (12% O(2)). Blood flow velocity in the middle cerebral artery (MCAv) and mean arterial blood pressure (MAP) were measured for determination of CA following calculation of transfer function analysis and rate of regulation (RoR). Nine subjects developed clinical AMS (AMS+) and were more hypoxaemic relative to subjects without AMS (AMS-). A more marked increase in the venous concentration of the ascorbate radical (A(*-)), lipid hydroperoxides (LOOH) and increased susceptibility of low-density lipoprotein (LDL) to oxidation was observed during hypoxia in AMS+ (P < 0.05 versus AMS-). Despite a general decline in total nitric oxide (NO) in hypoxia (P < 0.05 versus normoxia), the normoxic baseline plasma and red blood cell (RBC) NO metabolite pool was lower in AMS+ with normalization observed during hypoxia (P < 0.05 versus AMS-). CA was selectively impaired in AMS+ as indicated both by an increase in the low-frequency (0.07-0.20 Hz) transfer function gain and decrease in RoR (P < 0.05 versus AMS-). However, there was no evidence for cerebral hyper-perfusion, BBB disruption or neuronal-parenchymal damage as indicated by a lack of change in MCAv, S100beta and neuron-specific enolase. In conclusion, these findings suggest that AMS is associated with altered redox homeostasis and disordered CA independent of barrier disruption.

Concurrent encoding of frequency and amplitude modulation in human auditory cortex: encoding transition.

PubMed

Luo, Huan; Wang, Yadong; Poeppel, David; Simon, Jonathan Z

2007-12-01

Complex natural sounds (e.g., animal vocalizations or speech) can be characterized by specific spectrotemporal patterns the components of which change in both frequency (FM) and amplitude (AM). The neural coding of AM and FM has been widely studied in humans and animals but typically with either pure AM or pure FM stimuli. The neural mechanisms employed to perceptually unify AM and FM acoustic features remain unclear. Using stimuli with simultaneous sinusoidal AM (at rate f(AM) = 37 Hz) and FM (with varying rates f(FM)), magnetoencephalography (MEG) is used to investigate the elicited auditory steady-state response (aSSR) at relevant frequencies (f(AM), f(FM), f(AM) + f(FM)). Previous work demonstrated that for sounds with slower FM dynamics (f(FM) < 5 Hz), the phase of the aSSR at f(AM) tracked the FM; in other words, AM and FM features were co-tracked and co-represented by "phase modulation" encoding. This study explores the neural coding mechanism for stimuli with faster FM dynamics (< or =30 Hz), demonstrating that at faster rates (f(FM) > 5 Hz), there is a transition from pure phase modulation encoding to a single-upper-sideband (SSB) response (at frequency f(AM) + f(FM)) pattern. We propose that this unexpected SSB response can be explained by the additional involvement of subsidiary AM encoding responses simultaneously to, and in quadrature with, the ongoing phase modulation. These results, using MEG to reveal a possible neural encoding of specific acoustic properties, demonstrate more generally that physiological tests of encoding hypotheses can be performed noninvasively on human subjects, complementing invasive, single-unit recordings in animals.

The intersection of antimicrobial stewardship and microbiology: educating the next generation of health care professionals.

PubMed

O'Donnell, Lauren A; Guarascio, Anthony J

2017-01-01

With the alarming rise of antibiotic resistance, clinical professionals are called upon to manage antibiotic therapies using the most relevant and recent clinical and laboratory data. To this end, antimicrobial stewardship (AMS) programs aim to reduce unnecessary or suboptimal use of antibiotics while maximizing outcomes for the patient. For AMS programs to succeed, the active participation of clinical professionals at all levels of patient care is required. Although programs exist to train established clinicians in AMS, there is a paucity of literature on how and when to integrate AMS concepts and skills in pre-clinical and clinical coursework. Here, we discuss the crucial microbiology concepts and proficiencies that are necessary for building and supporting an AMS program. We provide recommendations for key points to include in clinical curricula in order to develop the necessary microbiology interpretation skills to participate in AMS. The influence of AMS programs on local organism susceptibility patterns is emphasized. The importance of antibiograms, rapid diagnostic testing and the practical interpretations of microbiology laboratory reporting are discussed in regard to prioritization in clinical curricula. We also review the current literature on instructional strategies for introducing AMS into clinical programs, and propose concepts that should be included in didactic coursework in order to provide a foundation for AMS education. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Systemic and local regulation of phosphate and nitrogen transporter genes by arbuscular mycorrhizal fungi in roots of winter wheat (Triticum aestivum L.).

PubMed

Duan, Jianfeng; Tian, Hui; Drijber, Rhae A; Gao, Yajun

2015-11-01

Previous studies have reported that the expression of phosphate (Pi) or nitrogen (N) transporter genes in roots of plants could be regulated by arbuscular mycorrhizal (AM) fungi, but little is known whether the regulation is systemic or not. The present study investigated the systemic and local regulation of multiple phosphate and nitrogen transporter genes by four AM fungal species belonging to four genera in the roots of winter wheat. A split-root culture system with AM inoculated (MR) and non-inoculated root compartments (NR) was used to investigate the systemic or local responses of phosphate and nitrogen transporter genes to colonization by four AM fungi in the roots of wheat. The expression of four Pi transporter, five nitrate transporter, and three ammonium transporter genes was quantified using real-time PCR. Of the four AM fungi tested, all locally increased expression of the AM-inducible Pi transporter genes, and most locally decreased expression of a Pi-starvation inducible Pi transporter gene. The addition of N in soil increased the expression of either Pi starvation inducible Pi transporters or AM inducible Pi transporters. Inoculation with AM fungi either had no effect, or could locally or systemically down-regulate expression of nitrogen transporter genes depending on gene type and AM fungal species. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

VIEW OF WATER SUPPLY TANK FOR THE PRESSURIZED SUBCRITICAL EXPERIMENT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF WATER SUPPLY TANK FOR THE PRESSURIZED SUBCRITICAL EXPERIMENT (PSE), LOCATED IN STAIRWELL ADJACENT TO SP-SE ROOM, LEVEL -15’, LOOKING NORTH - Physics Assembly Laboratory, Area A/M, Savannah River Site, Aiken, Aiken County, SC

Additively Manufactured Combustion Devices Components for LOX/Methane Applications

NASA Technical Reports Server (NTRS)

Greene, Sandra Elam; Protz, Christopher; Garcia, Chance; Goodman, Dwight; Baker, Kevin

2016-01-01

Marshall Space Flight Center (MSFC) has designed, fabricated, and hot-fire tested a variety of successful injectors, chambers, and igniters for potential liquid oxygen (LOX) and methane (CH4) systems since 2005. The most recent efforts have focused on components with additive manufacturing (AM) to include unique design features, minimize joints, and reduce final machining efforts. Inconel and copper alloys have been used with AM processes to produce a swirl coaxial injector and multiple methane cooled thrust chambers. The initial chambers included unique thermocouple ports for measuring local coolant channel temperatures along the length of the chamber. Results from hot-fire testing were used to anchor thermal models and generate a regeneratively cooled thruster for a 4,000 lbf LOX/CH4 engine. The completed thruster will be hot-fire tested in the summer of 2016 at MSFC. The thruster design can also be easily scaled and used on a 25,000 lbf engine. To further support the larger engine design, an AM gas generator injector has been designed. Hot-fire testing on this injector is planned for the summer of 2016 at MSFC.

Motility in the L3 stage is a poor phenotype for detecting and measuring resistance to avermectin/milbemycin drugs in gastrointestinal nematodes of livestock.

PubMed

George, Melissa M; Lopez-Soberal, Lorraine; Storey, Bob E; Howell, Sue B; Kaplan, Ray M

2018-04-01

Motility is a commonly used in vitro phenotype for assessing anthelmintic activity of candidate compounds, and for detecting anthelmintic resistance in nematodes. Third-stage larvae (L3) of parasitic nematodes are commonly used in motility-based assays because L3 are simple to obtain and can remain viable in storage for extended periods. To improve the measurement of motility of microscopic stages of nematodes, our laboratory developed the Worminator, which quantitatively measures motility of parasites. Using the Worminator, we compared the dose-response characteristics of several avermectin/milbemycin (AM) compounds using L3 from both AM-susceptible and AM-resistant Cooperia spp. (abamectin, doramectin, eprinomectin, ivermectin, moxidectin) and Haemonchus contortus (eprinomectin, ivermectin, moxidectin). Concentrations tested with the Worminator ranged from 0.156 to 40 μM. Differences in EC 50 between AM-susceptible and AM-resistant isolates of Cooperia spp. and Haemonchus contortus were small, with resistance ratios ranging from 1.00 to 1.34 for Cooperia spp., 0.99 to 1.65 for Haemonchus contortus. Larval migration inhibition assays were conducted using the same isolates and were equally ineffective for detection of resistance with resistance ratios less than 2.0. These results contrast with those of the Larval Development Assay where we obtained a resistance ratio of 16.48 using the same isolates of Haemonchus contortus. Moreover, even at the highest concentration tested (40 μM), 100% inhibition of motility was never achieved and EC 50 for Worminator assays were more than 100× higher than peak plasma levels achieved in vivo following treatment. These data demonstrate that dose-response characteristics for inhibition of motility in L3 of gastrointestinal nematodes of livestock do not significantly differ for AM-susceptible and AM-resistant isolates. These data challenge the suitability of motility as a phenotype for detecting and measuring resistance to AM drugs in gastrointestinal nematodes of livestock. Copyright © 2017. Published by Elsevier Ltd.

Synergistic activity of biocides and antibiotics on resistant bacteria from organically produced foods.

PubMed

Fernández Fuentes, Miguel Angel; Abriouel, Hikmate; Gadea, Rebeca; Pérez Pulido, Rubén; Gálvez, Antonio; Ortega, Elena

2014-10-01

Synergism between biocides and antibiotics was investigated in 20 biocide and antibiotic-resistant bacterial strains that were previously isolated from organically produced foods, according to their antimicrobial resistance profiles. Most of the antibiotic/biocide combinations yielded synergistic interactions, reducing the inhibitory concentrations of biocides and antibiotics by 4- to 16-fold. Among enterococci, synergism with biocides was detected for amoxicillin (AM), cefuroxime (CX), erythromycin (EM), ciprofloxacin (CP), and trimethoprim/sulphametoxazol (T/S). Among staphylococci, interactions were synergistic (AM) and either synergistic or indifferent (CX and EM, depending on biocide). Among the three methicillin-resistant Staphylococcus aureus clinical strains included in the study, the combinations of methicillin and triclosan or hexachlorophene acted synergistically in all strains, but interactions were either synergistic or indifferent for the other biocides, depending on the strain. All combinations tested were synergistic for Lactobacillus (AM, CX, EM, and CP) and Micrococcus (AM, EM). In Salmonella, interactions were indifferent (AM, CX, EM, and CP) or synergistic (T/S). Synergism with biocides was also detected in Klebsiella isolates (AM, CX, and T/S), Enterobacter sp. (AM, CX, EM, and T/S), Pantoea (AM, CX, EM, CP, and T/S), and Chryseobacterium sp. (EM). These results suggest that combinations of biocides and antibiotics may open new possibilities to combat antimicrobial resistance.

Glucose Transporter 1 Expression in Odontogenic Keratocyst, Dentigerous Cyst, and Ameloblastoma: An Immunohistochemical Study.

PubMed

Bandyopadhyay, Alokenath; Panda, Abikshyeet; Behura, Shyam S; Ramachandra, Sujatha; Dash, Kailash C; Mishra, Pallavi

2017-05-01

An array of odontogenic lesions manifest in the maxillofacial region with variable presentations. The biological behavior of lesions, such as odontogenic keratocyst (OKC), dentigerous cyst (DC), and ameloblastoma (AM) always invite debate. Glucose transporter 1 (GLUT-1) is proven to be an indicator of metabolic behavior of several benign and malignant neoplasms. The purpose of this study was to evaluate the expression of GLUT-1 in OKC, DC, and AM to understand their metabolic behavior. Immunohistochemical expression of GLUT-1 was evaluated in each of the 15 cases of OKC, DC, and AM. The number of labeled cells, staining intensity, and membrane or cytoplasmic expressions were the parameters assessed and analyzed using chi-square test. All cases showed positive GLUT-1 expression: 86.6% OKC showed more than 50% labeled cells followed by DC (40%) and AM (26.5%); 53.3% OKC showed strong intensity in comparison to AM, which showed weak intensity in 53.3% cases; 86.6% of OKCs showed both membrane and cytoplasmic expression followed by DC (40%) and AM (26.6%), whereas 73.3% of AM showed only membrane expression followed by DC (60%) and OKC (13.3%). Odontogenic keratocyst was found out to be more metabolically active followed by DC and AM.

Similar below-ground carbon cycling dynamics but contrasting modes of nitrogen cycling between arbuscular mycorrhizal and ectomycorrhizal forests.

PubMed

Lin, Guigang; McCormack, M Luke; Ma, Chengen; Guo, Dali

2017-02-01

Compared with ectomycorrhizal (ECM) forests, arbuscular mycorrhizal (AM) forests are hypothesized to have higher carbon (C) cycling rates and a more open nitrogen (N) cycle. To test this hypothesis, we synthesized 645 observations, including 22 variables related to below-ground C and N dynamics from 100 sites, where AM and ECM forests co-occurred at the same site. Leaf litter quality was lower in ECM than in AM trees, leading to greater forest floor C stocks in ECM forests. By contrast, AM forests had significantly higher mineral soil C concentrations, and this result was strongly mediated by plant traits and climate. No significant differences were found between AM and ECM forests in C fluxes and labile C concentrations. Furthermore, inorganic N concentrations, net N mineralization and nitrification rates were all higher in AM than in ECM forests, indicating 'mineral' N economy in AM but 'organic' N economy in ECM trees. AM and ECM forests show systematic differences in mineral vs organic N cycling, and thus mycorrhizal type may be useful in predicting how different tree species respond to multiple environmental change factors. By contrast, mycorrhizal type alone cannot reliably predict below-ground C dynamics without considering plant traits and climate. © 2016 The Authors. New Phytologist © 2016 New Phytologist Trust.

Sleep inertia during a simulated 6-h on/6-h off fixed split duty schedule.

PubMed

Hilditch, Cassie J; Short, Michelle; Van Dongen, Hans P A; Centofanti, Stephanie A; Dorrian, Jillian; Kohler, Mark; Banks, Siobhan

Sleep inertia is a safety concern for shift workers returning to work soon after waking up. Split duty schedules offer an alternative to longer shift periods, but introduce additional wake-ups and may therefore increase risk of sleep inertia. This study investigated sleep inertia across a split duty schedule. Sixteen participants (age range 21-36 years; 10 females) participated in a 9-day laboratory study with two baseline nights (10 h time in bed, [TIB]), four 24-h periods of a 6-h on/6-h off split duty schedule (5-h TIB in off period; 10-h TIB per 24 h) and two recovery nights. Two complementary rosters were evaluated, with the timing of sleep and wake alternating between the two rosters (2 am/2 pm wake-up roster versus 8 am/8 pm wake-up roster). At 2, 17, 32 and 47 min after scheduled awakening, participants completed an 8-min inertia test bout, which included a 3-min psychomotor vigilance test (PVT-B), a 3-min Digit-Symbol Substitution Task (DSST), the Karolinska Sleepiness Scale (KSS), and the Samn-Perelli Fatigue Scale (SP-Fatigue). Further testing occurred every 2 h during scheduled wakefulness. Performance was consistently degraded and subjective sleepiness/fatigue was consistently increased during the inertia testing period as compared to other testing times. Morning wake-ups (2 am and 8 am) were associated with higher levels of sleep inertia than later wake-ups (2 pm and 8 pm). These results suggest that split duty workers should recognise the potential for sleep inertia after waking, especially during the morning hours.