The impact of feeding growing-finishing pigs with daily tailored diets using precision feeding techniques on animal performance, nutrient utilization, and body and carcass composition.

PubMed

Andretta, I; Pomar, C; Rivest, J; Pomar, J; Lovatto, P A; Radünz Neto, J

2014-09-01

The impact of moving from conventional to precision feeding systems in growing-finishing pig operations on animal performance, nutrient utilization, and body and carcass composition was studied. Fifteen animals per treatment for a total of 60 pigs of 41.2 (SE = 0.5) kg of BW were used in a performance trial (84 d) with 4 treatments: a 3-phase (3P) feeding program obtained by blending fixed proportions of feeds A (high nutrient density) and B (low nutrient density); a 3-phase commercial (COM) feeding program; and 2 daily-phase feeding programs in which the blended proportions of feeds A and B were adjusted daily to meet the estimated nutritional requirements of the group (multiphase-group feeding, MPG) or of each pig individually (multiphase-individual feeding, MPI). Daily feed intake was recorded each day and pigs were weighed weekly during the trial. Body composition was assessed at the beginning of the trial and every 28 d by dual-energy X-ray densitometry. Nitrogen and phosphorus excretion was estimated as the difference between retention and intake. Organ, carcass, and primal cut measurements were taken after slaughter. The COM feeding program reduced (P < 0.05) ADFI and improved G:F rate in relation to other treatments. The MPG and MPI programs showed values for ADFI, ADG, G:F, final BW, and nitrogen and phosphorus retention that were similar to those obtained for the 3P feeding program. However, compared with the 3P treatment, the MPI feeding program reduced the standardized ileal digestible lysine intake by 27%, the estimated nitrogen excretion by 22%, and the estimated phosphorus excretion by 27% (P < 0.05). Organs, carcass, and primal cut weights did not differ among treatments. Feeding growing-finishing pigs with daily tailored diets using precision feeding techniques is an effective approach to reduce nutrient excretion without compromising pig performance or carcass composition.

Simultaneous determination of eight cyclopolypeptide antibiotics in feed by high performance liquid chromatography coupled with evaporation light scattering detection.

PubMed

Song, Xuqin; Xie, Jingmeng; Zhang, Meiyu; Zhang, Yingxia; Li, Jiufeng; Huang, Qiwen; He, Limin

2018-02-15

A high throughput, reliable and reproducible analysis strategy based on high performance liquid chromatography combined to evaporative light scattering detector (HPLC-ELSD) was developed for simultaneous determination of eight cyclopolypeptide antibiotics including vancomycin, polymyxin B (polymyxin B1 and polymyxin B2), polymyxin E (colistin A and colistin B), teicoplanin, bacitracin A, daptomycin and virginiamycin M1 in animal Feed. Feed samples were extracted with methanol-2% formic acid aqueous solution, followed by a solid-phase extraction step using a HLB cartridge. Under the optimum chromatographic conditions and ELSD parameters, target compounds were separated well on a short column filled with biphenyl stationary phase. The method was developed in accordance with pig complete feed and then extended to detect polypeptide antibiotics in piglet premix, pig feed additive, poultry complete feed and fattening pig premix. The results showed that logarithmic calibration curves of eight analytes were linear (r 2  > 0.99) within the concentration range of 5-200 mg mL -1 . The developed method provided good accuracy and precision for quantification of eight polypeptides in five kinds of feeds with recoveries ranging from 72.0% to 105.4% with relative standard deviations <9.5%. The limits of detection ranged from 2 to 5 mg kg -1 . Finally, the method was successfully applied to analyze polypeptide antibiotics in commercial feed. Copyright © 2018 Elsevier B.V. All rights reserved.

Determination of d-limonene in adipose tissue by gas chromatography-mass spectrometry

PubMed Central

Miller, Jessica A.; Hakim, Iman A.; Thomson, Cynthia; Thompson, Patricia; Chow, H-H. Sherry

2008-01-01

We developed a novel method for analyzing d-limonene levels in adipose tissue. Fat samples were subjected to saponification followed by solvent extraction. d-Limonene in the sample extract was analyzed using gas chromatography-mass spectrometry (GC-MS) with selected ion monitoring. Linear calibration curves were established over the mass range of 79.0-2,529 ng d-limonene per 0.1 grams of adipose tissue. Satisfactory within day precision (RSD 6.7 to 9.6%) and accuracy (% difference of −2.7 to 3.8%) and between day precision (RSD 6.0 to 10.7%) and accuracy (% difference of 1.8 to 2.6%) were achieved. The assay was successfully applied to human fat biopsy samples from a d-limonene feeding trial. PMID:18571481

Analysis of the Growth Process of Neural Cells in Culture Environment Using Image Processing Techniques

NASA Astrophysics Data System (ADS)

Mirsafianf, Atefeh S.; Isfahani, Shirin N.; Kasaei, Shohreh; Mobasheri, Hamid

Here we present an approach for processing neural cells images to analyze their growth process in culture environment. We have applied several image processing techniques for: 1- Environmental noise reduction, 2- Neural cells segmentation, 3- Neural cells classification based on their dendrites' growth conditions, and 4- neurons' features Extraction and measurement (e.g., like cell body area, number of dendrites, axon's length, and so on). Due to the large amount of noise in the images, we have used feed forward artificial neural networks to detect edges more precisely.

Duplex communicable implanted antenna for magnetic direct feeding method: Functional electrical stimulation

NASA Astrophysics Data System (ADS)

Kato, Kentaro; Matsuki, Hidetoshi; Sato, Fumihiro; Satoh, Tadakuni; Handa, Nobuyasu

2009-04-01

Functional electrical stimulation (FES) is the therapy used for the rehabilitation of lost movement function by applying electrical stimulation (ES) to paralyzed extremities. To realize ES, we adapted the implanted direct feeding method (DFM). In this method, small implanted stimulators are placed under the skin at a depth of 10-20 mm and stimulus energy and signals for controlling devices are applied to them by a mounted system using magnetic coupling. This method has the merits of having no percutaneous points and high-precision stimulation. However, since the mounted system and implanted elements are separated, it is necessary to add feedback information from inside the body to confirm the system operation for safety therapy or to rehabilitate motor function smoothly. Satisfying both restrictions, we propose the magnetic connective dual resonance (MCDR) antenna, which has two resonance circuits. Adding the LC serial circuit to the LC parallel circuit gives the sending function. In this paper, we report the principle of the MCDR antenna and verify its duplex communication ability through communication experiment. This antenna enables DFM of FES to rehabilitate more complex movements.

Integrated modeling and analysis of the multiple electromechanical couplings for the direct driven feed system in machine tools

NASA Astrophysics Data System (ADS)

Yang, Xiaojun; Lu, Dun; Liu, Hui; Zhao, Wanhua

2018-06-01

The complicated electromechanical coupling phenomena due to different kinds of causes have significant influences on the dynamic precision of the direct driven feed system in machine tools. In this paper, a novel integrated modeling and analysis method of the multiple electromechanical couplings for the direct driven feed system in machine tools is presented. At first, four different kinds of electromechanical coupling phenomena in the direct driven feed system are analyzed systematically. Then a novel integrated modeling and analysis method of the electromechanical coupling which is influenced by multiple factors is put forward. In addition, the effects of multiple electromechanical couplings on the dynamic precision of the feed system and their main influencing factors are compared and discussed, respectively. Finally, the results of modeling and analysis are verified by the experiments. It finds out that multiple electromechanical coupling loops, which are overlapped and influenced by each other, are the main reasons of the displacement fluctuations in the direct driven feed system.

LC-MS/MS methods for sulfadimethoxine and ormetoprim analysis in feed and fish fillet and a leaching study for feed after alternative procedures for the incorporation of drugs.

PubMed

Fais, Ana Paula; Franco, Rodolfo Scarpino Barboza; da Silva, Agnaldo Fernando Baldo; de Freitas, Osvaldo; Paschoal, Jonas Augusto Rizzato

2017-04-01

This paper describes the method development for sulfadimethoxine (SDM) and ormetoprim (OMP) quantitation in fish feed and fish fillet employing LC-MS/MS. In order to assess the reliability of the analytical method, valuation was undertaken as recommended by guidelines proposed by the Brazilian Ministry of Agriculture. The calibration curve for the quantification of both drugs in feed showed adequate linearity (r > 0.99), precision (CV < 12%) and trueness ranging from 97% to 100%. The method for the determination of SDM and OMP residues in fish fillet involved a simple sample preparation procedure that had adequate linearity (r > 0.99), precision (CV < 16%) and trueness around 100%, with CCα < 100.2 ng g - 1 and CCβ < 100.4 ng g - 1 . With a goal of avoiding the risk of drug leaching from feed into the aquatic environment during fish medication via the oral route, different procedures for drug incorporation into feed were evaluated. Coating feed pellets with ethyl cellulose polymer containing the drug showed promising results. In this case, medicated feed released drugs to water at a level below 6% when the medicated feed stayed in the water for up to 15 min.

New approach for the quantification of processed animal proteins in feed using light microscopy.

PubMed

Veys, P; Baeten, V

2010-07-01

A revision of European Union's total feed ban on animal proteins in feed will need robust quantification methods, especially for control analyses, if tolerance levels are to be introduced, as for fishmeal in ruminant feed. In 2006, a study conducted by the Community Reference Laboratory for Animal Proteins in feedstuffs (CRL-AP) demonstrated the deficiency of the official quantification method based on light microscopy. The study concluded that the method had to be revised. This paper puts forward an improved quantification method based on three elements: (1) the preparation of permanent slides with an optical adhesive preserving all morphological markers of bones necessary for accurate identification and precision counting; (2) the use of a counting grid eyepiece reticle; and (3) new definitions for correction factors for the estimated portions of animal particles in the sediment. This revised quantification method was tested on feeds adulterated at different levels with bovine meat and bone meal (MBM) and fishmeal, and it proved to be effortless to apply. The results obtained were very close to the expected values of contamination levels for both types of adulteration (MBM or fishmeal). Calculated values were not only replicable, but also reproducible. The advantages of the new approach, including the benefits of the optical adhesive used for permanent slide mounting and the experimental conditions that need to be met to implement the new method correctly, are discussed.

Organization of feed-forward loop motifs reveals architectural principles in natural and engineered networks.

PubMed

Gorochowski, Thomas E; Grierson, Claire S; di Bernardo, Mario

2018-03-01

Network motifs are significantly overrepresented subgraphs that have been proposed as building blocks for natural and engineered networks. Detailed functional analysis has been performed for many types of motif in isolation, but less is known about how motifs work together to perform complex tasks. To address this issue, we measure the aggregation of network motifs via methods that extract precisely how these structures are connected. Applying this approach to a broad spectrum of networked systems and focusing on the widespread feed-forward loop motif, we uncover striking differences in motif organization. The types of connection are often highly constrained, differ between domains, and clearly capture architectural principles. We show how this information can be used to effectively predict functionally important nodes in the metabolic network of Escherichia coli . Our findings have implications for understanding how networked systems are constructed from motif parts and elucidate constraints that guide their evolution.

Organization of feed-forward loop motifs reveals architectural principles in natural and engineered networks

PubMed Central

Grierson, Claire S.

2018-01-01

Network motifs are significantly overrepresented subgraphs that have been proposed as building blocks for natural and engineered networks. Detailed functional analysis has been performed for many types of motif in isolation, but less is known about how motifs work together to perform complex tasks. To address this issue, we measure the aggregation of network motifs via methods that extract precisely how these structures are connected. Applying this approach to a broad spectrum of networked systems and focusing on the widespread feed-forward loop motif, we uncover striking differences in motif organization. The types of connection are often highly constrained, differ between domains, and clearly capture architectural principles. We show how this information can be used to effectively predict functionally important nodes in the metabolic network of Escherichia coli. Our findings have implications for understanding how networked systems are constructed from motif parts and elucidate constraints that guide their evolution. PMID:29670941

Simultaneously precise frequency transfer and time synchronization using feed-forward compensation technique via 120 km fiber link.

PubMed

Chen, Xing; Lu, Jinlong; Cui, Yifan; Zhang, Jian; Lu, Xing; Tian, Xusheng; Ci, Cheng; Liu, Bo; Wu, Hong; Tang, Tingsong; Shi, Kebin; Zhang, Zhigang

2015-12-22

Precision time synchronization between two remote sites is desired in many applications such as global positioning satellite systems, long-baseline interferometry, coherent radar detection and fundamental physics constant measurements. The recently developed frequency dissemination technologies based on optical fiber link have improved the transfer instability to the level of 10(-19)/day at remote location. Therefore it is possible to keep clock oscillation at remote locations continuously corrected, or to reproduce a "virtual" clock on the remote location. However the initial alignment and the correction of 1 pps timing signal from time to time are still required, besides the highly stabilized clock frequency transfer between distant locations. Here we demonstrate a time synchronization based on an ultra-stable frequency transfer system via 120-km commercial fiber link by transferring an optical frequency comb. Both the phase noise compensation in frequency dissemination and temporal basis alignment in time synchronization were implemented by a feed-forward digital compensation (FFDC) technique. The fractional frequency instability was measured to be 6.18 × 10(-20) at 2000 s. The timing deviation of time synchronization was measured to be 0.6 ps in 1500 s. This technique also can be applied in multi-node fiber network topology.

Simultaneously precise frequency transfer and time synchronization using feed-forward compensation technique via 120 km fiber link

PubMed Central

Chen, Xing; Lu, Jinlong; Cui, Yifan; Zhang, Jian; Lu, Xing; Tian, Xusheng; Ci, Cheng; Liu, Bo; Wu, Hong; Tang, Tingsong; Shi, Kebin; Zhang, Zhigang

2015-01-01

Precision time synchronization between two remote sites is desired in many applications such as global positioning satellite systems, long-baseline interferometry, coherent radar detection and fundamental physics constant measurements. The recently developed frequency dissemination technologies based on optical fiber link have improved the transfer instability to the level of 10−19/day at remote location. Therefore it is possible to keep clock oscillation at remote locations continuously corrected, or to reproduce a “virtual” clock on the remote location. However the initial alignment and the correction of 1 pps timing signal from time to time are still required, besides the highly stabilized clock frequency transfer between distant locations. Here we demonstrate a time synchronization based on an ultra-stable frequency transfer system via 120-km commercial fiber link by transferring an optical frequency comb. Both the phase noise compensation in frequency dissemination and temporal basis alignment in time synchronization were implemented by a feed-forward digital compensation (FFDC) technique. The fractional frequency instability was measured to be 6.18 × 10−20 at 2000 s. The timing deviation of time synchronization was measured to be 0.6 ps in 1500 s. This technique also can be applied in multi-node fiber network topology. PMID:26691731

Precision PEP-II optics measurement with an SVD-enhanced Least-Square fitting

NASA Astrophysics Data System (ADS)

Yan, Y. T.; Cai, Y.

2006-03-01

A singular value decomposition (SVD)-enhanced Least-Square fitting technique is discussed. By automatic identifying, ordering, and selecting dominant SVD modes of the derivative matrix that responds to the variations of the variables, the converging process of the Least-Square fitting is significantly enhanced. Thus the fitting speed can be fast enough for a fairly large system. This technique has been successfully applied to precision PEP-II optics measurement in which we determine all quadrupole strengths (both normal and skew components) and sextupole feed-downs as well as all BPM gains and BPM cross-plane couplings through Least-Square fitting of the phase advances and the Local Green's functions as well as the coupling ellipses among BPMs. The local Green's functions are specified by 4 local transfer matrix components R12, R34, R32, R14. These measurable quantities (the Green's functions, the phase advances and the coupling ellipse tilt angles and axis ratios) are obtained by analyzing turn-by-turn Beam Position Monitor (BPM) data with a high-resolution model-independent analysis (MIA). Once all of the quadrupoles and sextupole feed-downs are determined, we obtain a computer virtual accelerator which matches the real accelerator in linear optics. Thus, beta functions, linear coupling parameters, and interaction point (IP) optics characteristics can be measured and displayed.

Earth Science Datacasting v2.0

NASA Technical Reports Server (NTRS)

Bingham, Andrew W.; Deen, Robert G.; Hussey, Kevin J.; Stough, Timothy M.; McCleese, Sean W.; Toole, Nicholas T.

2012-01-01

The Datacasting software, which consists of a server and a client, has been developed as part of the Earth Science (ES) Datacasting project. The goal of ES Datacasting is to provide scientists the ability to automatically and continuously download Earth science data that meets a precise, predefined need, and then to instantaneously visualize it on a local computer. This is achieved by applying the concept of podcasting to deliver science data over the Internet using RSS (Really Simple Syndication) XML feeds. By extending the RSS specification, scientists can filter a feed and only download the files that are required for a particular application (for example, only files that contain information about a particular event, such as a hurricane or flood). The extension also provides the ability for the client to understand the format of the data and visualize the information locally. The server part enables a data provider to create and serve basic Datacasting (RSS-based) feeds. The user can subscribe to any number of feeds, view the information related to each item contained within a feed (including browse pre-made images), manually download files associated with items, and place these files in a local store. The client-server architecture enables users to: a) Subscribe and interpret multiple Datacasting feeds (same look and feel as a typical mail client), b) Maintain a list of all items within each feed, c) Enable filtering on the lists based on different metadata attributes contained within the feed (list will reference only data files of interest), d) Visualize the reference data and associated metadata, e) Download files referenced within the list, and f) Automatically download files as new items become available.

Usefulness of high-resolution 3D multifusion medical imaging for preoperative planning in patients with posterior fossa hemangioblastoma: technical note.

PubMed

Yoshino, Masanori; Nakatomi, Hirofumi; Kin, Taichi; Saito, Toki; Shono, Naoyuki; Nomura, Seiji; Nakagawa, Daichi; Takayanagi, Shunsaku; Imai, Hideaki; Oyama, Hiroshi; Saito, Nobuhito

2017-07-01

Successful resection of hemangioblastoma depends on preoperative assessment of the precise locations of feeding arteries and draining veins. Simultaneous 3D visualization of feeding arteries, draining veins, and surrounding structures is needed. The present study evaluated the usefulness of high-resolution 3D multifusion medical imaging (hr-3DMMI) for preoperative planning of hemangioblastoma. The hr-3DMMI combined MRI, MR angiography, thin-slice CT, and 3D rotated angiography. Surface rendering was mainly used for the creation of hr-3DMMI using multiple thresholds to create 3D models, and processing took approximately 3-5 hours. This hr-3DMMI technique was used in 5 patients for preoperative planning and the imaging findings were compared with the operative findings. Hr-3DMMI could simulate the whole 3D tumor as a unique sphere and show the precise penetration points of both feeding arteries and draining veins with the same spatial relationships as the original tumor. All feeding arteries and draining veins were found intraoperatively at the same position as estimated preoperatively, and were occluded as planned preoperatively. This hr-3DMMI technique could demonstrate the precise locations of feeding arteries and draining veins preoperatively and estimate the appropriate route for resection of the tumor. Hr-3DMMI is expected to be a very useful support tool for surgery of hemangioblastoma.

Gas cushion control of OVJP print head position

DOE Office of Scientific and Technical Information (OSTI.GOV)

Forrest, Stephen R

An OVJP apparatus and method for applying organic vapor or other flowable material to a substrate using a printing head mechanism in which the print head spacing from the substrate is controllable using a cushion of air or other gas applied between the print head and substrate. The print head is mounted for translational movement towards and away from the substrate and is biased toward the substrate by springs or other means. A gas cushion feed assembly supplies a gas under pressure between the print head and substrate which opposes the biasing of the print head toward the substrate somore » as to form a space between the print head and substrate. By controlling the pressure of gas supplied, the print head separation from the substrate can be precisely controlled.« less

LC-MS/MS methods for albendazole analysis in feed and its metabolite residues in fish fillet and a leaching study in feed after an alternative procedure for drug incorporation.

PubMed

Busatto, Zenaís; da Silva, Agnaldo Fernando Baldo; de Freitas, Osvaldo; Paschoal, Jonas Augusto Rizzato

2017-04-01

This paper describes the development of analytical methods for the quantification of albendazole (ABZ) in fish feed and ABZ and its main known metabolites (albendazole sulfoxide, albendazole sulfone and albendazole aminosulfone) in fish fillet employing LC-MS/MS. In order to assess the reliability of the analytical methods, evaluation was undertaken as recommended by related guides proposed by the Brazilian Ministry of Agriculture for analytical method validation. The calibration curve for ABZ quantification in feed showed adequate linearity (r > 0.99), precision (CV < 1.03%) and trueness ranging from 99% to 101%. The method for ABZ residues in fish fillet involving the QuEChERS technique for sample extraction had adequate linearity (r > 0.99) for all analytes, precision (CV < 13%) and trueness around 100%, with CCα < 122 ng g - 1 and CCβ < 145 ng g - 1 . Besides, by aiming to avoid the risk of ABZ leaching from feed into the aquatic environment during fish medication via the oral route, a promising procedure for drug incorporation in the feed involving coating feed pellets with ethyl cellulose polymer containing ABZ was also evaluated. The medicated feed had good homogeneity (CV < 3%) and a lower release of ABZ (< 0.2%) from feed to water when the medicated feed stayed in the water for up to 15 min.

Does choice of estimators influence conclusions from true metabolizable energy feeding trials?

USGS Publications Warehouse

Sherfy, M.H.; Kirkpatrick, R.L.; Webb, K.E.

2005-01-01

True metabolizable energy (TME) is a measure of avian dietary quality that accounts for metabolic fecal and endogenous urinary energy losses (EL) of non-dietary origin. The TME is calculated using a bird fed the test diet and an estimate of EL derived from another bird (Paired Bird Correction), the same bird (Self Correction), or several other birds (Group Mean Correction). We evaluated precision of these estimators by using each to calculate TME of three seed diets in blue-winged teal (Anas discors). The TME varied by <2% among estimators for all three diets, and Self Correction produced the least variable TMEs for each. The TME did not differ between estimators in nine paired comparisons within diets, but variation between estimators within individual birds was sufficient to be of practical consequence. Although differences in precision among methods were slight, Self Correction required the lowest sample size to achieve a given precision. Feeding trial methods that minimize variation among individuals have several desirable properties, including higher precision of TME estimates and more rigorous experimental control. Consequently, we believe that Self Correction is most likely to accurately represent nutritional value of food items and should be considered the standard method for TME feeding trials. ?? Dt. Ornithologen-Gesellschaft e.V. 2005.

Multivariate Optimization of Conditions for Digestion of Wet Feeds for Dogs and Cats Using a Closed Digester Block and Multielement Determination by ICP-OES.

PubMed

Ávila, Dayara Virgínia Lino; Souza, Sidnei Oliveira; Costa, Silvânio Silvério Lopes; Garcia, Carlos Alexandre Borges; Alves, José do Patrocínio Hora; Araujo, Rennan Geovanny Oliveira; Passos, Elisangela Andrade

2017-09-01

A full 24 factorial design was applied to find the best combination of diluted reagents (HNO3 and H2O2), time, and temperature for the digestion of samples of wet feed for dogs and cats using a closed digestion block. The residual carbon concentration (RCC) was used as the response in the factorial design. All variables and their interactions significantly influenced the digestion of the feed samples, as indicated by the RCC. The conditions established for the digestion of 0.05 g (dry mass) wet feed samples were the addition of 3.0 mol/L HNO3 and 5.0% m/m H2O2 in a final volume of 10 mL, followed by heating in a closed digestion block at a temperature of 170°C for 120 min. Analyses were performed by inductively coupled plasma (ICP) optical emission spectrometry (OES). LOQs ranged from 0.2 μg/g (Mg and Sr) to 51 μg/g (P). Accuracy of the analytical method was confirmed through the analysis of the Standard Reference Materials Tomato Leaves (NIST 1573), Apple Leaves (NIST 1515), and Peach Leaves (NIST 1547). The agreement values achieved ranged from 80.2 ± 0.3% for Ba to 113.8 ± 7.1% for Zn (n = 3). Addition and recovery tests were carried out by adding the analytes to a feed sample at two concentration levels, and the recoveries were between 84 ± 6 and 114 ± 10% for macroelements (Ca, K, Mg, and P; n = 3) and between 88 ± 3 and 113 ± 7% for microelements and trace elements (B, Cu, Fe, Sr, and Zn; n = 3). The precision values achieved for the different elements, expressed as RSDs, were better than 7.3% (Zn; n = 3) except for Cu determination, that was 14.6% (n=3). The optimized analytical method was applied to 10 commercial samples of wet feed for cats and dogs, with the concentrations of Al, B, Ba, Ca, Cu, Fe, K, Mg, Mn, P, Sr, and Zn determined by ICP-OES.

Determination of emamectin benzoate in medicated fish feed: a multisite study.

PubMed

Farer, Leslie J

2005-01-01

A new method was developed for the quantitation of emamectin benzoate in medicated fish feed at levels between 1 and 30 ppm. The new procedure, based on a previously reported assay, consists of a wet methanolic extraction of ground feed, followed by solid-phase extraction and injection onto a gradient liquid chromatographic system. A multisite study involving 3 laboratories (the developing laboratory and 2 independent laboratories) was performed to evaluate precision, recovery, linearity, and sensitivity. Mean recove;ries for triplicate analyses at 3 levels, performed by 2 analysts per laboratory, were between 89 and 97%, with coefficients of variation ranging from 1.6 to 8.6%. Coefficients of determination (r2) obtained from the plotted data were > or =0.993. The precision of the method, determined from 6 replicate preparations from the same batch of medicated feed assayed in 3 separate trials per laboratory, was between 0.6 and 5.8%. The quantitation limit was established at 0.5 ppm. Specificity and robustness studies were performed by the developing laboratory.

Electromagnetic variable degrees of freedom actuator systems and methods

DOEpatents

Montesanti, Richard C [Pleasanton, CA; Trumper, David L [Plaistow, NH; Kirtley, Jr., James L.

2009-02-17

The present invention provides a variable reluctance actuator system and method that can be adapted for simultaneous rotation and translation of a moving element by applying a normal-direction magnetic flux on the moving element. In a beneficial example arrangement, the moving element includes a swing arm that carries a cutting tool at a set radius from an axis of rotation so as to produce a rotary fast tool servo that provides a tool motion in a direction substantially parallel to the surface-normal of a workpiece at the point of contact between the cutting tool and workpiece. An actuator rotates a swing arm such that a cutting tool moves toward and away from a mounted rotating workpiece in a controlled manner in order to machine the workpiece. Position sensors provide rotation and displacement information for a swing arm to a control system. A control system commands and coordinates motion of the fast tool servo with the motion of a spindle, rotating table, cross-feed slide, and in feed slide of a precision lathe.

Automatic real-time pair-feeding system for animals

NASA Technical Reports Server (NTRS)

Leon, H. A.; Connolly, J. P.; Hitchman, M. J.; Humbert, J. E. (Inventor)

1974-01-01

A pair feeding method and apparatus are provided for experimental animals wherein the amount of food consumed is immediately delivered to a normal or control animal so that there is a qualitative, quantitative and chronological correctness in the pair feeding of the two animals. This feeding mechanism delivers precisely measured amounts of food to a feeder. Circuitry is provided between master and slave feeders so that there is virtually no chance of a malfunction of the feeding apparatus, causing erratic results. Recording equipment is also provided so that an hourly record is kept of food delivery.

Generalized Autobalanced Ramsey Spectroscopy of Clock Transitions

NASA Astrophysics Data System (ADS)

Yudin, V. I.; Taichenachev, A. V.; Basalaev, M. Yu.; Zanon-Willette, T.; Pollock, J. W.; Shuker, M.; Donley, E. A.; Kitching, J.

2018-05-01

When performing precision measurements, the quantity being measured is often perturbed by the measurement process itself. Such measurements include precision frequency measurements for atomic clock applications carried out with Ramsey spectroscopy. With the aim of eliminating probe-induced perturbations, a method of generalized autobalanced Ramsey spectroscopy (GABRS) is presented and rigorously substantiated. The usual local-oscillator frequency control loop is augmented with a second control loop derived from secondary Ramsey sequences interspersed with the primary sequences and with a different Ramsey period. This second loop feeds back to a secondary clock variable and ultimately compensates for the perturbation of the clock frequency caused by the measurements in the first loop. We show that such a two-loop scheme can lead to perfect compensation for measurement-induced light shifts and does not suffer from the effects of relaxation, time-dependent pulse fluctuations and phase-jump modulation errors that are typical of other hyper-Ramsey schemes. Several variants of GABRS are explored based on different secondary variables including added relative phase shifts between Ramsey pulses, external frequency-step compensation, and variable second-pulse duration. We demonstrate that a universal antisymmetric error signal, and hence perfect compensation at a finite modulation amplitude, is generated only if an additional frequency step applied during both Ramsey pulses is used as the concomitant variable parameter. This universal technique can be applied to the fields of atomic clocks, high-resolution molecular spectroscopy, magnetically induced and two-photon probing schemes, Ramsey-type mass spectrometry, and the field of precision measurements. Some variants of GABRS can also be applied for rf atomic clocks using coherent-population-trapping-based Ramsey spectroscopy of the two-photon dark resonance.

Determination of caffeoylquinic acids in feed and related products by focused ultrasound solid-liquid extraction and ultra-high performance liquid chromatography-mass spectrometry.

PubMed

Tena, M T; Martínez-Moral, M P; Cardozo, P W

2015-06-26

A method to determine caffeoylquinic acids (CQAs) in three sources (herbal extract, feed additive and finished feed) using for the first time focused ultrasound solid-liquid extraction (FUSLE) followed by ultra-high performance liquid chromatography (UPLC) coupled to quadrupole-time of flight mass spectrometry is presented. Pressurized liquid extraction (PLE) was also tested as extraction technique but it was discarded because cynarin was not stable under temperature values used in PLE. The separation of the CQAs isomers was carried out in only seven minutes. FUSLE variables such as extraction solvent, power and time were optimized by a central composite design. Under optimal conditions, FUSLE extraction was performed with 8mL of an 83:17 methanol-water mixture for 30s at a power of 60%. Only two extraction steps were found necessary to recover analytes quantitatively. Sensitivity, linearity, accuracy and precision were established. Matrix effect was studied for each type of sample. It was not detected for mono-CQAs, whereas the cynarin signal was strongly decreased due to ionization suppression in presence of matrix components; so the quantification by standard addition was mandatory for the determination of di-caffeoylquinic acids. Finally, the method was applied to the analysis of herbal extracts, feed additives and finished feed. In all samples, chlorogenic acid was the predominant CQA, followed by criptochlorogenic acid, neochlorogenic acid and cynarin. The method allows an efficient determination of chlorogenic acid with good recovery rates. Therefore, it may be used for screening of raw material and for process and quality control in feed manufacture. Copyright © 2015 Elsevier B.V. All rights reserved.

Real time monitoring of powder blend bulk density for coupled feed-forward/feed-back control of a continuous direct compaction tablet manufacturing process.

PubMed

Singh, Ravendra; Román-Ospino, Andrés D; Romañach, Rodolfo J; Ierapetritou, Marianthi; Ramachandran, Rohit

2015-11-10

The pharmaceutical industry is strictly regulated, where precise and accurate control of the end product quality is necessary to ensure the effectiveness of the drug products. For such control, the process and raw materials variability ideally need to be fed-forward in real time into an automatic control system so that a proactive action can be taken before it can affect the end product quality. Variations in raw material properties (e.g., particle size), feeder hopper level, amount of lubrication, milling and blending action, applied shear in different processing stages can affect the blend density significantly and thereby tablet weight, hardness and dissolution. Therefore, real time monitoring of powder bulk density variability and its incorporation into the automatic control system so that its effect can be mitigated proactively and efficiently is highly desired. However, real time monitoring of powder bulk density is still a challenging task because of different level of complexities. In this work, powder bulk density which has a significant effect on the critical quality attributes (CQA's) has been monitored in real time in a pilot-plant facility, using a NIR sensor. The sensitivity of the powder bulk density on critical process parameters (CPP's) and CQA's has been analyzed and thereby feed-forward controller has been designed. The measured signal can be used for feed-forward control so that the corrective actions on the density variations can be taken before they can influence the product quality. The coupled feed-forward/feed-back control system demonstrates improved control performance and improvements in the final product quality in the presence of process and raw material variations. Copyright © 2015 Elsevier B.V. All rights reserved.

Development and validation of an LC-MS/MS method for the quantification of tiamulin, trimethoprim, tylosin, sulfadiazine and sulfamethazine in medicated feed.

PubMed

Patyra, Ewelina; Nebot, Carolina; Gavilán, Rosa Elvira; Cepeda, Alberto; Kwiatek, Krzysztof

2018-05-01

A new multi-compound method for the analysis of veterinary drugs, namely tiamulin, trimethoprim, tylosin, sulfadiazine and sulfamethazine was developed and validated in medicated feeds. After extraction, the samples were centrifuged, diluted in Milli-Q water, filtered and analysed by high performance liquid chromatography coupled to tandem mass spectrometry. The separation of the analytes was performed on a biphenyl column with a gradient of 0.1% formic acid in acetonitrile and 0.1% formic acid in Milli-Q water. Quantitative validation was done in accordance with the guidelines laid down in European Commission Decision 2002/657/EC. Method performances were evaluated by the following parameters: linearity (R 2  < 0.99), precision (repeatability <14% and within-laboratory reproducibility <24%), recovery (73.58-115.21%), sensitivity, limit of detection (LOD), limit of quantification (LOQ), selectivity and expanded measurement uncertainty (k. = 2). The validated method was successfully applied to the 2 medicated feeds obtained from the interlaboratory studies and feed manufactures from Spain in August 2017. In these samples, tiamulin, tylosin and sulfamethazine were detected at the concentration levels declared by the manufacturers. The developed method can therefore be successfully used to routinely control the content and homogeneity of these antibacterial substances in medicated feed. Abbreviations AAFCO - Association of American Feed Control Officials; TYL - tylosin; TIAM - tiamulin fumarate; TRIM - trimethoprim; SDZ - sulfadiazine; SMZ - sulfamethazine; UV - ultraviolet detector; FLD - fluorescence detector; HPLC - high performance liquid chromatography; MS/MS - tandem mass spectrometry; LOD - limit of detection; LOQ - limit of quantification; CV - coefficient of variation; SD - standard deviation; U - uncertainty.

Scrambling and modal noise mitigation in the Habitable Zone Planet Finder fiber feed

NASA Astrophysics Data System (ADS)

Roy, Arpita; Halverson, Samuel; Mahadevan, Suvrath; Ramsey, Lawrence W.

2014-07-01

We present the baseline fiber feed design for the Habitable-zone Planet Finder (HPF), a precision radial velocity (RV) spectrograph designed to detect Earth analogs around M-dwarfs. HPF is a stabilized, fiber-fed, R˜50,000 spectrograph operating in the near-infrared (NIR) from 0.82 to 1.3 µm, and will be deployed on the Hobby- Eberly Telescope (HET) in Texas. While the essential function of the optical fibers is to deliver high throughput, this mode of light transport also provides the opportunity to introduce radial and azimuthal scrambling, which boosts instrument stability and thereby RV precision. Based on the unique requirements of HPF on the HET, we present initial tests showing very high scrambling gains via a compact scrambler in conjunction with octagonal fibers. Conversely, the propagation of light through the fibers injects modal noise, which can limit achievable RV precision. Laboratory tests of a custom-built mechanical agitator show significant gains over a static fiber feed. Overall, the fiber feed is designed to provide high relative throughput, excellent scrambling, and reliable modal noise suppression. We will also attempt to minimize focal ratio degradation (FRD) to the extent possible with the chosen configuration. HPF inculcates several other new technologies developed by the Penn State Optical-Infrared instrumentation group, including a rigorous calibration system, which are discussed separately in these proceedings.

Research note: the performance of spring- and summer-reared broilers as affected by precision beak trimming at seven days of age.

PubMed

Christmas, R B

1993-12-01

In each of two duplicate trials approximately 2,500 day-old Peterson x Arbor Acres straight-run broiler chicks were equally divided between two treatments of three pens each. Treatment 1 was maintained as controls (C), and Treatment 2 birds were precision beak-trimmed (PBT) at 7 days of age. Feed and water were supplied for ad libitum consumption to both groups. Trials 1 and 2 were initiated in March and June, respectively. Performance of spring-reared broilers were comparable regardless of beak trimming procedure, except that PBT broilers experienced slightly higher mortality after PBT. Final body weights of the summer-reared broilers were 15% lower than those reared in the spring. Additionally, PBT resulted in significantly reduced final body weights and feed intake. There were no significant differences in mortality or feed conversion due to PBT.

Optimization of A 2-Micron Laser Frequency Stabilization System for a Double-Pulse CO2 Differential Absorption Lidar

NASA Technical Reports Server (NTRS)

Chen, Songsheng; Yu, Jirong; Bai, Yingsin; Koch, Grady; Petros, Mulugeta; Trieu, Bo; Petzar, Paul; Singh, Upendra N.; Kavaya, Michael J.; Beyon, Jeffrey

2010-01-01

A carbon dioxide (CO2) Differential Absorption Lidar (DIAL) for accurate CO2 concentration measurement requires a frequency locking system to achieve high frequency locking precision and stability. We describe the frequency locking system utilizing Frequency Modulation (FM), Phase Sensitive Detection (PSD), and Proportional Integration Derivative (PID) feedback servo loop, and report the optimization of the sensitivity of the system for the feed back loop based on the characteristics of a variable path-length CO2 gas cell. The CO2 gas cell is characterized with HITRAN database (2004). The method can be applied for any other frequency locking systems referring to gas absorption line.

Drilling Precise Orifices and Slots

NASA Technical Reports Server (NTRS)

Richards, C. W.; Seidler, J. E.

1983-01-01

Reaction control thrustor injector requires precisely machined orifices and slots. Tooling setup consists of rotary table, numerical control system and torque sensitive drill press. Components used to drill oxidizer orifices. Electric discharge machine drills fuel-feed orifices. Device automates production of identical parts so several are completed in less time than previously.

Packaging, deployment, and panel design concepts for a truss-stiffened 7-panel precision deployable reflector with feed boom

NASA Technical Reports Server (NTRS)

Heard, Walter L., Jr.; Collins, Timothy J.; Dyess, James W.; Kenner, Scott; Bush, Harold G.

1993-01-01

A concept is presented for achieving a remotely deployable truss-stiffened reflector consisting of seven integrated sandwich panels that form the reflective surface, and an integrated feed boom. The concept has potential for meeting aperture size and surface precision requirements for some high-frequency microwave remote sensing applications. The packaged reflector/feed boom configuration is a self-contained unit that can be conveniently attached to a spacecraft bus. The package has a cylindrical envelope compatible with typical launch vehicle shrouds. Dynamic behavior of a deployed configuration having a 216-inch focal length and consisting of 80-inch-diameter, two-inch-thick panels is examined through finite-element analysis. Results show that the feed boom and spacecraft bus can have a large impact on the fundamental frequency of the deployed configuration. Two candidate rib-stiffened sandwich panel configurations for this application are described, and analytical results for panel mass and stiffness are presented. Results show that the addition of only a few rib stiffeners, if sufficiently deep, can efficiently improve sandwich panel stiffness.

Personalized weight change prediction in the first week of life.

PubMed

Wilbaux, Mélanie; Kasser, Severin; Gromann, Julia; Mancino, Isabella; Coscia, Tania; Lapaire, Olav; van den Anker, Johannes N; Pfister, Marc; Wellmann, Sven

2018-04-11

Almost all neonates show physiological weight loss and consecutive weight gain after birth. The resulting weight change profiles are highly variable as they depend on multiple neonatal and maternal factors. This limits the value of weight nomograms for the early identification of neonates at risk for excessive weight loss and related morbidities. The objective of this study was to characterize weight changes and the effect of supplemental feeding in late preterm and term neonates during the first week of life, to identify and quantify neonatal and maternal influencing factors, and to provide an educational online prediction tool. Longitudinal weight data from 3638 healthy term and late preterm neonates were prospectively recorded up to 7 days of life. Two-thirds (n = 2425) were randomized to develop a semi-mechanistic model characterizing weight change as a balance between time-dependent rates of weight gain and weight loss. The dose-dependent effect of supplemental feeding on weight gain was characterized. A population analysis applying nonlinear mixed-effects modeling was performed using NONMEM 7.3. The model was evaluated on the remaining third of neonates (n = 1213). Key population characteristics (median [range]) of the whole sample were gestational age 39.9 [34.4-42.4] weeks, birth weight 3400 [1980-5580] g, maternal age 32 [15-51] years, cesarean section 26%, and girls 50%. The model demonstrated good predictive performance (bias 0.01%, precision 0.56%), and is able to accurately predict individual weight change (bias 0.15%, precision 1.43%) and the dose-dependent effects of supplemental feeding up to 1 week after birth based on weight measurements during the first 3 days of life, including birth weight, and the following characteristics: gestational age, gender, delivery mode, type of feeding, maternal age, and parity. We present the first mathematical model not only to describe weight change in term and late preterm neonates but also to provide an educational online tool for personalized weight prediction in the first week of life. Copyright © 2018 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Evaluation of analytical techniques to determine AQUI-S® 20E (eugenol) concentrations in water

USGS Publications Warehouse

Meinertz, Jeffery R.; Hess, Karina R.

2014-01-01

There is a critical need in U.S. public aquaculture and fishery management programs for an immediate-release sedative, i.e. a compound that can be safely and effectively used to sedate fish and subsequently, allow for their immediate release. AQUI-S® 20E (10% active ingredient, eugenol; any use of trade, firm, or product names is for descriptive purposes only and does not imply endorsement by the U.S. Government) is being pursued for U.S. approval as an immediate-release sedative. As part of the approval process, data describing animal safety and efficacy are needed. Essential to conducting studies that generate those data, is a method to accurately and precisely determine AQUI-S® 20E concentrations in exposure baths. Spectrophotometric and solid phase extraction (SPE)–high pressure liquid chromatography (LC) methods were developed and evaluated as methods to determine AQUI-S® 20E (eugenol) concentrations in water, methods that could be applied to any situation where eugenol was being evaluated as a fish sedative. The spectrophotometric method was accurate and precise (accuracy, > 87%; precision, 86%; precision < 8.9 %CV) when determining eugenol concentrations in solutions of 50 to 1000 mg/L AQUI-S® 20E made with LC grade water and water with varying pH and hardness. The SPE–LC method was influenced to a lesser degree by the presence of fish feed indicating greater specificity for eugenol.

Experimental investigation of the tip based micro/nano machining

NASA Astrophysics Data System (ADS)

Guo, Z.; Tian, Y.; Liu, X.; Wang, F.; Zhou, C.; Zhang, D.

2017-12-01

Based on the self-developed three dimensional micro/nano machining system, the effects of machining parameters and sample material on micro/nano machining are investigated. The micro/nano machining system is mainly composed of the probe system and micro/nano positioning stage. The former is applied to control the normal load and the latter is utilized to realize high precision motion in the xy plane. A sample examination method is firstly introduced to estimate whether the sample is placed horizontally. The machining parameters include scratching direction, speed, cycles, normal load and feed. According to the experimental results, the scratching depth is significantly affected by the normal load in all four defined scratching directions but is rarely influenced by the scratching speed. The increase of scratching cycle number can increase the scratching depth as well as smooth the groove wall. In addition, the scratching tests of silicon and copper attest that the harder material is easier to be removed. In the scratching with different feed amount, the machining results indicate that the machined depth increases as the feed reduces. Further, a cubic polynomial is used to fit the experimental results to predict the scratching depth. With the selected machining parameters of scratching direction d3/d4, scratching speed 5 μm/s and feed 0.06 μm, some more micro structures including stair, sinusoidal groove, Chinese character '田', 'TJU' and Chinese panda have been fabricated on the silicon substrate.

Quantitative Analysis of Food and Feed Samples with Droplet Digital PCR

PubMed Central

Morisset, Dany; Štebih, Dejan; Milavec, Mojca; Gruden, Kristina; Žel, Jana

2013-01-01

In this study, the applicability of droplet digital PCR (ddPCR) for routine analysis in food and feed samples was demonstrated with the quantification of genetically modified organisms (GMOs). Real-time quantitative polymerase chain reaction (qPCR) is currently used for quantitative molecular analysis of the presence of GMOs in products. However, its use is limited for detecting and quantifying very small numbers of DNA targets, as in some complex food and feed matrices. Using ddPCR duplex assay, we have measured the absolute numbers of MON810 transgene and hmg maize reference gene copies in DNA samples. Key performance parameters of the assay were determined. The ddPCR system is shown to offer precise absolute and relative quantification of targets, without the need for calibration curves. The sensitivity (five target DNA copies) of the ddPCR assay compares well with those of individual qPCR assays and of the chamber digital PCR (cdPCR) approach. It offers a dynamic range over four orders of magnitude, greater than that of cdPCR. Moreover, when compared to qPCR, the ddPCR assay showed better repeatability at low target concentrations and a greater tolerance to inhibitors. Finally, ddPCR throughput and cost are advantageous relative to those of qPCR for routine GMO quantification. It is thus concluded that ddPCR technology can be applied for routine quantification of GMOs, or any other domain where quantitative analysis of food and feed samples is needed. PMID:23658750

75 FR 39869 - Airworthiness Directives; Airbus Model A330-200 and A330-300 Series Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-13

... uncommanded engine 1 in flight spool down, which occurred while applying fuel gravity feed procedure, in... while applying fuel gravity feed procedure, in response to low pressure indications from all fuel boost... applying fuel gravity feed procedure, in response to low pressure indications from all fuel boost pumps, in...

Gas Furnace with Pulsed Feeding of the Heating Agent for Volume Precision Heat Treatment of CCM Rolls

NASA Astrophysics Data System (ADS)

Moroz, V. I.; Egorova, V. M.; Gusev, S. V.

2001-05-01

A standard chamber batch furnace of the Severstal' plant has been modified for precision heat treatment of CCM rolls. The certification tests of a charge of rolls from steel 24KhM1F have shown the technical and economical advantages of the new design.

Techniques for evaluating digestibility of energy, amino acids, phosphorus, and calcium in feed ingredients for pigs.

PubMed

Zhang, Fengrui; Adeola, Olayiwola

2017-12-01

Sound feed formulation is dependent upon precise evaluation of energy and nutrients values in feed ingredients. Hence the methodology to determine the digestibility of energy and nutrients in feedstuffs should be chosen carefully before conducting experiments. The direct and difference procedures are widely used to determine the digestibility of energy and nutrients in feedstuffs. The direct procedure is normally considered when the test feedstuff can be formulated as the sole source of the component of interest in the test diet. However, in some cases where test ingredients can only be formulated to replace a portion of the basal diet to provide the component of interest, the difference procedure can be applied to get equally robust values. Based on components of interest, ileal digesta or feces can be collected, and different sample collection processes can be used. For example, for amino acids (AA), to avoid the interference of fermentation in the hind gut, ileal digesta samples are collected to determine the ileal digestibility and simple T-cannula and index method are commonly used techniques for AA digestibility analysis. For energy, phosphorus, and calcium, normally fecal samples will be collected to determine the total tract digestibility, and therefore the total collection method is recommended to obtain more accurate estimates. Concerns with the use of apparent digestibility values include different estimated values from different inclusion level and non-additivity in mixtures of feed ingredients. These concerns can be overcome by using standardized digestibility, or true digestibility, by correcting endogenous losses of components from apparent digestibility values. In this review, methodologies used to determine energy and nutrients digestibility in pigs are discussed. It is suggested that the methodology should be carefully selected based on the component of interest, feed ingredients, and available experimental facilities.

Alternative prediction methods of protein and energy evaluation of pig feeds.

PubMed

Święch, Ewa

2017-01-01

Precise knowledge of the actual nutritional value of individual feedstuffs and complete diets for pigs is important for efficient livestock production. Methods of assessment of protein and energy values in pig feeds have been briefly described. In vivo determination of protein and energy values of feeds in pigs are time-consuming, expensive and very often require the use of surgically-modified animals. There is a need for more simple, rapid, inexpensive and reproducible methods for routine feed evaluation. Protein and energy values of pig feeds can be estimated using the following alternative methods: 1) prediction equations based on chemical composition; 2) animal models as rats, cockerels and growing pigs for adult animals; 3) rapid methods, such as the mobile nylon bag technique and in vitro methods. Alternative methods developed for predicting the total tract and ileal digestibility of nutrients including amino acids in feedstuffs and diets for pigs have been reviewed. This article focuses on two in vitro methods that can be used for the routine evaluation of amino acid ileal digestibility and energy value of pig feeds and on factors affecting digestibility determined in vivo in pigs and by alternative methods. Validation of alternative methods has been carried out by comparing the results obtained using these methods with those acquired in vivo in pigs. In conclusion, energy and protein values of pig feeds may be estimated with satisfactory precision in rats and by the two- or three-step in vitro methods providing equations for the calculation of standardized ileal digestibility of amino acids and metabolizable energy content. The use of alternative methods of feed evaluation is an important way for reduction of stressful animal experiments.

Gas Fuelling System for SST-1Tokamak

NASA Astrophysics Data System (ADS)

Dhanani, Kalpesh; Raval, D. C.; Khan, Ziauddin; Semwal, Pratibha; George, Siju; Paravastu, Yuvakiran; Thankey, Prashant; Khan, M. S.; Pradhan, Subrata

2017-04-01

SST-1 Tokamak, the first Indian Steady-state Superconducting experimental device is at present under operation in the Institute for Plasma Research. For plasma break down & initiation, piezoelectric valve based gas feed system is implemented as a primary requirement due to its precise control, easy handling, low construction and maintenance cost and its flexibility in the selection of the working gas. Hydrogen gas feeding with piezoelectric valve is used in the SST-1 plasma experiments. The piezoelectric valves used in SST-1 are remotely driven by a PXI based platform and are calibrated before each SST-1 plasma operation with precise control. This paper will present the technical development and the results of the gas fuelling system of SST-1.

Evaluation of a method estimating real-time individual lysine requirements in two lines of growing-finishing pigs.

PubMed

Cloutier, L; Pomar, C; Létourneau Montminy, M P; Bernier, J F; Pomar, J

2015-04-01

The implementation of precision feeding in growing-finishing facilities requires accurate estimates of the animals' nutrient requirements. The objectives of the current study was to validate a method for estimating the real-time individual standardized ileal digestible (SID) lysine (Lys) requirements of growing-finishing pigs and the ability of this method to estimate the Lys requirements of pigs with different feed intake and growth patterns. Seventy-five pigs from a terminal cross and 72 pigs from a maternal cross were used in two 28-day experimental phases beginning at 25.8 (±2.5) and 73.3 (±5.2) kg BW, respectively. Treatments were randomly assigned to pigs within each experimental phase according to a 2×4 factorial design in which the two genetic lines and four dietary SID Lys levels (70%, 85%, 100% and 115% of the requirements estimated by the factorial method developed for precision feeding) were the main factors. Individual pigs' Lys requirements were estimated daily using a factorial approach based on their feed intake, BW and weight gain patterns. From 25 to 50 kg BW, this method slightly underestimated the pigs' SID Lys requirements, given that maximum protein deposition and weight gain were achieved at 115% of SID Lys requirements. However, the best gain-to-feed ratio (G : F) was obtained at a level of 85% or more of the estimated Lys requirement. From 70 to 100 kg, the method adequately estimated the pigs' individual requirements, given that maximum performance was achieved at 100% of Lys requirements. Terminal line pigs ate more (P=0.04) during the first experimental phase and tended to eat more (P=0.10) during the second phase than the maternal line pigs but both genetic lines had similar ADG and protein deposition rates during the two phases. The factorial method used in this study to estimate individual daily SID Lys requirements was able to accommodate the small genetic differences in feed intake, and it was concluded that this method can be used in precision feeding systems without adjustments. However, the method's ability to accommodate large genetic differences in feed intake and protein deposition patterns needs to be studied further.

Inferring the Diets of Extinct Giant Lemurs from Osteological Correlates of Muscle Dimensions.

PubMed

Perry, Jonathan M G

2018-02-01

The jaw adductor muscles of extinct mammals are often reconstructed to elucidate paleoecological relationships and to make broad comparisons among taxa. Muscle lever arms, bite load arms, muscle dimensions, and gape are often also reconstructed to better understand feeding. Several different approaches to these and related goals are discussed here. A protocol for reconstructing muscle dimensions and bite force using biomechanically informative skull measurements and osteological proxies of muscle dimensions is described and applied to a case study of subfossil Malagasy lemurs. The results of this case study show that most subfossil lemurs emphasized the masseter and medial pterygoid muscles over the temporalis. This supports the inference that these extinct lemurs depended heavily on tough food like leaves. Exceptions include signals of hard-object feeding in Archaeolemur that vary between A. majori and A. edwardsi. Reconstructions of soft-tissue and function are important for understanding past ecological relationships. Even those based on well-supported osteological proxies from extant analogues have limitations for making precise inferences. Anat Rec, 301:343-362, 2018. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.

A new simple asymmetric hysteresis operator and its application to inverse control of piezoelectric actuators.

PubMed

Badel, A; Qiu, J; Nakano, T

2008-05-01

Piezoelectric actuators (PEAs) are commonly used as micropositioning devices due to their high resolution, high stiffness, and fast frequency response. Because piezoceramic materials are ferroelectric, they fundamentally exhibit hysteresis behavior in their response to an applied electric field. The positioning precision can be significantly reduced due to nonlinear hysteresis effects when PEAs are used in relatively long range applications. This paper describes a new, precise, and simple asymmetric hysteresis operator dedicated to PEAs. The complex hysteretic transfer characteristic has been considered in a purely phenomenological way, without taking into account the underlying physics. This operator is based on two curves. The first curve corresponds to the main ascending branch and is modeled by the function f1. The second curve corresponds to the main reversal branch and is modeled by the function g2. The functions f(1) and g(2) are two very simple hyperbola functions with only three parameters. Particular ascending and reversal branches are deduced from appropriate translations of f(1) and g(2). The efficiency and precision of the proposed approach is demonstrated, in practice, by a real-time inverse feed-forward controller for piezoelectric actuators. Advantages and drawbacks of the proposed approach compared with classical hysteresis operators are discussed.

Analysis on the multi-dimensional spectrum of the thrust force for the linear motor feed drive system in machine tools

NASA Astrophysics Data System (ADS)

Yang, Xiaojun; Lu, Dun; Ma, Chengfang; Zhang, Jun; Zhao, Wanhua

2017-01-01

The motor thrust force has lots of harmonic components due to the nonlinearity of drive circuit and motor itself in the linear motor feed drive system. What is more, in the motion process, these thrust force harmonics may vary with the position, velocity, acceleration and load, which affects the displacement fluctuation of the feed drive system. Therefore, in this paper, on the basis of the thrust force spectrum obtained by the Maxwell equation and the electromagnetic energy method, the multi-dimensional variation of each thrust harmonic is analyzed under different motion parameters. Then the model of the servo system is established oriented to the dynamic precision. The influence of the variation of the thrust force spectrum on the displacement fluctuation is discussed. At last the experiments are carried out to verify the theoretical analysis above. It can be found that the thrust harmonics show multi-dimensional spectrum characteristics under different motion parameters and loads, which should be considered to choose the motion parameters and optimize the servo control parameters in the high-speed and high-precision machine tools equipped with the linear motor feed drive system.

Feeding-Related Traits Are Affected by Dosage of the foraging Gene in Drosophila melanogaster

PubMed Central

Allen, Aaron M.; Anreiter, Ina; Neville, Megan C.; Sokolowski, Marla B.

2017-01-01

Nutrient acquisition and energy storage are critical parts of achieving metabolic homeostasis. The foraging gene in Drosophila melanogaster has previously been implicated in multiple feeding-related and metabolic traits. Before foraging’s functions can be further dissected, we need a precise genetic null mutant to definitively map its amorphic phenotypes. We used homologous recombination to precisely delete foraging, generating the for0 null allele, and used recombineering to reintegrate a full copy of the gene, generating the {forBAC} rescue allele. We show that a total loss of foraging expression in larvae results in reduced larval path length and food intake behavior, while conversely showing an increase in triglyceride levels. Furthermore, varying foraging gene dosage demonstrates a linear dose-response on these phenotypes in relation to foraging gene expression levels. These experiments have unequivocally proven a causal, dose-dependent relationship between the foraging gene and its pleiotropic influence on these feeding-related traits. Our analysis of foraging’s transcription start sites, termination sites, and splicing patterns using rapid amplification of cDNA ends (RACE) and full-length cDNA sequencing, revealed four independent promoters, pr1–4, that produce 21 transcripts with nine distinct open reading frames (ORFs). The use of alternative promoters and alternative splicing at the foraging locus creates diversity and flexibility in the regulation of gene expression, and ultimately function. Future studies will exploit these genetic tools to precisely dissect the isoform- and tissue-specific requirements of foraging’s functions and shed light on the genetic control of feeding-related traits involved in energy homeostasis. PMID:28007892

Precision diet formulation to improve performance and profitability across various climates: Modeling the implications of increasing the formulation frequency of dairy cattle diets.

PubMed

White, Robin R; Capper, Judith L

2014-03-01

The objective of this study was to use a precision nutrition model to simulate the relationship between diet formulation frequency and dairy cattle performance across various climates. Agricultural Modeling and Training Systems (AMTS) CattlePro diet-balancing software (Cornell Research Foundation, Ithaca, NY) was used to compare 3 diet formulation frequencies (weekly, monthly, or seasonal) and 3 levels of climate variability (hot, cold, or variable). Predicted daily milk yield (MY), metabolizable energy (ME) balance, and dry matter intake (DMI) were recorded for each frequency-variability combination. Economic analysis was conducted to calculate the predicted revenue over feed and labor costs. Diet formulation frequency affected ME balance and MY but did not affect DMI. Climate variability affected ME balance and DMI but not MY. The interaction between climate variability and formulation frequency did not affect ME balance, MY, or DMI. Formulating diets more frequently increased MY, DMI, and ME balance. Economic analysis showed that formulating diets weekly rather than seasonally could improve returns over variable costs by $25,000 per year for a moderate-sized (300-cow) operation. To achieve this increase in returns, an entire feeding system margin of error of <1% was required. Formulating monthly, rather than seasonally, may be a more feasible alternative as this requires a margin of error of only 2.5% for the entire feeding system. Feeding systems with a low margin of error must be developed to better take advantage of the benefits of precision nutrition. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

A biomimetic hybrid nanoplatform for encapsulation and precisely controlled delivery of therasnostic agents

NASA Astrophysics Data System (ADS)

Wang, Hai; Agarwal, Pranay; Zhao, Shuting; Yu, Jianhua; Lu, Xiongbin; He, Xiaoming

2015-12-01

Nanoparticles have demonstrated great potential for enhancing drug delivery. However, the low drug encapsulation efficiency at high drug-to-nanoparticle feeding ratios and minimal drug loading content in nanoparticle at any feeding ratios are major hurdles to their widespread applications. Here we report a robust eukaryotic cell-like hybrid nanoplatform (EukaCell) for encapsulation of theranostic agents (doxorubicin and indocyanine green). The EukaCell consists of a phospholipid membrane, a cytoskeleton-like mesoporous silica matrix and a nucleus-like fullerene core. At high drug-to-nanoparticle feeding ratios (for example, 1:0.5), the encapsulation efficiency and loading content can be improved by 58 and 21 times, respectively, compared with conventional silica nanoparticles. Moreover, release of the encapsulated drug can be precisely controlled via dosing near infrared laser irradiation. Ultimately, the ultra-high (up to ~87%) loading content renders augmented anticancer capacity both in vitro and in vivo. Our EukaCell is valuable for drug delivery to fight against cancer and potentially other diseases.

Theoretical implications of quantitative properties of interval timing and probability estimation in mouse and rat.

PubMed

Kheifets, Aaron; Freestone, David; Gallistel, C R

2017-07-01

In three experiments with mice ( Mus musculus ) and rats (Rattus norvigicus), we used a switch paradigm to measure quantitative properties of the interval-timing mechanism. We found that: 1) Rodents adjusted the precision of their timed switches in response to changes in the interval between the short and long feed latencies (the temporal goalposts). 2) The variability in the timing of the switch response was reduced or unchanged in the face of large trial-to-trial random variability in the short and long feed latencies. 3) The adjustment in the distribution of switch latencies in response to changes in the relative frequency of short and long trials was sensitive to the asymmetry in the Kullback-Leibler divergence. The three results suggest that durations are represented with adjustable precision, that they are timed by multiple timers, and that there is a trial-by-trial (episodic) record of feed latencies in memory. © 2017 Society for the Experimental Analysis of Behavior.

LINC-NIRVANA piston control elements

NASA Astrophysics Data System (ADS)

Brix, Mario; Pott, Jörg-Uwe; Bertram, Thomas; Rost, Steffen; Borelli, Jose Luis; Herbst, Thomas M.; Kuerster, Martin; Rohloff, Ralf-Rainer

2010-07-01

We review the status of hardware developments related to the Linc-Nirvana optical path difference (OPD) control. The status of our telescope vibration measurements is given. We present the design concept of a feed-forward loop to damp the impact of telescope mirror vibrations on the OPD seen by Linc-Nirvana. At the focus of the article is a description of the actuator of the OPD control loop. The weight and vibration optimized construction of this actuator (aka piston mirror) and its mount has a complex dynamical behavior, which prevents classical PI feedback control from delivering fast and precise motion of the mirror surface. Therefore, an H-; optimized control strategy will be applied, custom designed for the piston mirror. The effort of realizing a custom controller on a DSP to drive the piezo is balanced by the outlook of achieving more than 5x faster servo bandwidths. The laboratory set-up to identify the system, and verify the closed loop control performance is presented. Our goal is to achieve 30 Hz closed-loop control bandwidth at a precision of 30 nm.

Propagating synchrony in feed-forward networks

PubMed Central

Jahnke, Sven; Memmesheimer, Raoul-Martin; Timme, Marc

2013-01-01

Coordinated patterns of precisely timed action potentials (spikes) emerge in a variety of neural circuits but their dynamical origin is still not well understood. One hypothesis states that synchronous activity propagating through feed-forward chains of groups of neurons (synfire chains) may dynamically generate such spike patterns. Additionally, synfire chains offer the possibility to enable reliable signal transmission. So far, mostly densely connected chains, often with all-to-all connectivity between groups, have been theoretically and computationally studied. Yet, such prominent feed-forward structures have not been observed experimentally. Here we analytically and numerically investigate under which conditions diluted feed-forward chains may exhibit synchrony propagation. In addition to conventional linear input summation, we study the impact of non-linear, non-additive summation accounting for the effect of fast dendritic spikes. The non-linearities promote synchronous inputs to generate precisely timed spikes. We identify how non-additive coupling relaxes the conditions on connectivity such that it enables synchrony propagation at connectivities substantially lower than required for linearly coupled chains. Although the analytical treatment is based on a simple leaky integrate-and-fire neuron model, we show how to generalize our methods to biologically more detailed neuron models and verify our results by numerical simulations with, e.g., Hodgkin Huxley type neurons. PMID:24298251

Infant survival, HIV infection, and feeding alternatives in less-developed countries.

PubMed Central

Kuhn, L; Stein, Z

1997-01-01

OBJECTIVES: This study examines, in the context of the human immunodeficiency virus (HIV) epidemic, the effects of optimal breast-feeding, complete avoidance of breast-feeding, and early cessation of breast-feeding. METHODS: The three categories of breast-feeding were weighed in terms of HIV transmission and infant mortality. Estimates of the frequency of adverse outcomes were obtained by simulation. RESULTS: Avoidance of all breast-feeding by the whole population always produces the worst outcome. The lowest frequency of adverse outcomes occurs if no HIV-seropositive women breast-feed and all seronegative women breast-feed optimally, given infant mortality rates below 100 per 1000 and relative risks of dying set at 2.5 for non-breast-fed compared with optimally breast-fed infants. For known HIV-seropositive mothers, fewer adverse outcomes result from early cessation than from prolonged breast-feeding if the hazard of HIV transmission through breast-feeding after 3 months is 7% or more, even at high mortality rates, given relative risks of dying set at 1.5 for early cessation compared with optimal duration of breast-feeding. CONCLUSIONS: The risk of HIV transmission through breast-feeding at various ages needs to be more precisely quantified. The grave issues that may accompany a possible decline in breast-feeding in the less developed world demand evaluation. PMID:9224171

An in situ postexposure feeding assay with Carcinus maenas for estuarine sediment-overlying water toxicity evaluations.

PubMed

Moreira, Susana M; Moreira-Santos, Matilde; Guilhermino, Lúcia; Ribeiro, Rui

2006-01-01

This study developed and evaluated a short-term sublethal in situ toxicity assay for estuarine sediment-overlying waters, with the crab Carcinus maenas (L.) based on postexposure feeding. It consisted of a 48-h in situ exposure period followed by a short postexposure feeding period (30 min). A precise method for quantifying feeding, using the Polychaeta Hediste (Nereis) diversicolor Müller as food source, was first developed. The sensitivity of the postexposure feeding response was verified by comparing it to that of lethality, upon cadmium exposure. The influence of environmental conditions prevailing during exposure (salinity, temperature, substrate, light regime, and food availability) on postexposure feeding was also addressed. The potential of this in situ assay was then investigated by deploying organisms at ten sites, located in reference and contaminated Portuguese estuaries. Organism recovery ranged between 90% and 100% and a significant postexposure feeding depression (16.3-72.7%) was observed at all contaminated sites relatively to references.

75 FR 66651 - Airworthiness Directives; Airbus Model A330-201, -202, -203, -223, and -243 Airplanes, and Model...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-29

... spool down, which occurred while applying fuel gravity feed procedure, in response to low pressure... fuel gravity feed procedure, in response to low pressure indications from all fuel boost pumps, in both... while applying fuel gravity feed procedure, in response to low pressure indications from all fuel boost...

Plasma arc torch with coaxial wire feed

DOEpatents

Hooper, Frederick M

2002-01-01

A plasma arc welding apparatus having a coaxial wire feed. The apparatus includes a plasma arc welding torch, a wire guide disposed coaxially inside of the plasma arc welding torch, and a hollow non-consumable electrode. The coaxial wire guide feeds non-electrified filler wire through the tip of the hollow non-consumable electrode during plasma arc welding. Non-electrified filler wires as small as 0.010 inches can be used. This invention allows precision control of the positioning and feeding of the filler wire during plasma arc welding. Since the non-electrified filler wire is fed coaxially through the center of the plasma arc torch's electrode and nozzle, the wire is automatically aimed at the optimum point in the weld zone. Therefore, there is no need for additional equipment to position and feed the filler wire from the side before or during welding.

Feeding tube replacement: not always that simple!

PubMed Central

Lederman, Alex; Coelho da Rocha, Ricardo Frank; Lourenção, Rodrigo Montenegro

2015-01-01

Although surgical gastrostomy is not a technically troublesome surgery, the procedure may be accompanied by unfavorable outcomes. Most complications occur early in the post-operative period and include feeding tube dislodgment, stomal infection, peritonitis, and pneumonia. The authors report the case of an 83-year-old man who underwent a surgical gastrostomy because of a swallowing disorder after an ischemic stroke. Nine months after the procedure, the feeding tube dislodged and a new tube was inserted with a certain delay and with some difficulty, causing a false path and consequently an intrabdominal abscess after diet infusion. The outcome was fatal. The authors call attention for meticulous care with the insertion of feeding tubes and advise the performance of imaging control to assure its precise positioning. PMID:26484325

Online, efficient and precision laser profiling of bronze-bonded diamond grinding wheels based on a single-layer deep-cutting intermittent feeding method

NASA Astrophysics Data System (ADS)

Deng, Hui; Chen, Genyu; He, Jie; Zhou, Cong; Du, Han; Wang, Yanyi

2016-06-01

In this study, an online, efficient and precision laser profiling approach that is based on a single-layer deep-cutting intermittent feeding method is described. The effects of the laser cutting depth and the track-overlap ratio of the laser cutting on the efficiency, precision and quality of laser profiling were investigated. Experiments on the online profiling of bronze-bonded diamond grinding wheels were performed using a pulsed fiber laser. The results demonstrate that an increase in the laser cutting depth caused an increase in the material removal efficiency during the laser profiling process. However, the maximum laser profiling efficiency was only achieved when the laser cutting depth was equivalent to the initial surface contour error of the grinding wheel. In addition, the selection of relatively high track-overlap ratios of laser cutting for the profiling of grinding wheels was beneficial with respect to the increase in the precision of laser profiling, whereas the efficiency and quality of the laser profiling were not affected by the change in the track-overlap ratio. After optimized process parameters were employed for online laser profiling, the circular run-out error and the parallelism error of the grinding wheel surface decreased from 83.1 μm and 324.6 μm to 11.3 μm and 3.5 μm, respectively. The surface contour precision of the grinding wheel significantly improved. The highest surface contour precision for grinding wheels of the same type that can be theoretically achieved after laser profiling is completely dependent on the peak power density of the laser. The higher the laser peak power density is, the higher the surface contour precision of the grinding wheel after profiling.

Confirmatory analysis of 17beta-boldenone, 17alpha-boldenone and androsta-1,4-diene-3,17-dione in bovine urine, faeces, feed and skin swab samples by liquid chromatography-electrospray ionisation tandem mass spectrometry.

PubMed

Nielen, Michel W F; Rutgers, Paula; van Bennekom, Eric O; Lasaroms, Johan J P; van Rhijn, J A Hans

2004-03-05

The origin, i.e. natural occurrence or illegal treatment, of findings of 17alpha-boldenone (alpha-Bol) and 17beta-boldenone (beta-Bol) in urine and faeces of cattle is under debate within the European Union. A liquid chromatographic positive ion electrospray tandem mass spectrometric method is presented for the confirmatory analysis of 17beta-boldenone, 17alpha-boldenone and an important metabolite/precursor androsta-1,4-diene-3,17-dione (ADD), using deuterium-labelled 17beta-boldenone (beta-Bol-d3) as internal standard. Detailed sample preparation procedures were developed for a variety of sample matrices such as bovine urine, faeces, feed and skin swab samples. The method was validated as a quantitative confirmatory method according to the latest EU guidelines and shows good precision, linearity and accuracy data, and CCalpha and CCbeta values of 0.1-0.3 and 0.4-1.0 ng/ml, respectively. Currently, the method has been successfully applied to suspect urine samples for more than a year, and occasionally to faeces, feed and swab samples as well. Results obtained from untreated and treated animals are given and their impact on the debate about the origin of residues of 17beta-boldenone is critically discussed. Finally, preliminary data about the degree of conjugation of boldenone residues are presented and a simple procedure for discrimination between residues from abuse versus natural origin is proposed.

40 CFR 63.11627 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... feed supplements; prepared animal feeds; specialty animal (e.g., guinea pig, mice, mink) feeds; fish... the purposes of this subpart. Average daily feed production level means the average amount of animal... feed production level is based on the one-year period prior to the compliance date for existing sources...

An Ultra-Precise Method for the Nano Thin-Film Removal

NASA Astrophysics Data System (ADS)

Pa, P. S.

In this research an electrode-set is used to investigate via an ultra-precise method for the removal of Indium Tin Oxide (ITO) thin-film microstructure from defective display panels to conquer the low yield rate in display panel production as to from imperfect Indium Tin Oxide layer deposition is well known. This process, which involves the removal of ITO layer substructure by means of an electrochemical removal (ECMR), is of major interest to the optoelectronics semiconductor industry. In this electro machining process a high current flow and high feed rate of the display (color filter) achieves complete and efficient removal of the ITO layer. The ITO thin-film can be removed completely by a proper combination of feed rate and electric power. A small gap between the diameter cathode virtual rotation circle and the diameter virtual rotation circle also corresponds to a higher removal rate. A small anode edge radius with a small cathode edge radius effectively improves dregs discharge and is an advantage when associated with a high workpiece feed rate. This precision method for the recycling of defective display screen color filters is presented as an effective tool for use in the screen manufacturing process. The defective Indium Tin Oxide thin-film can be removed easily and cleanly in a short time. The complete removal of the ITO layer makes it possible to put these panels back into the production line for reuse with a considerable reduction of both waste and production cost.

Lateral vibration control of a precise machine using magneto-rheological mounts featuring multiple directional damping effect

NASA Astrophysics Data System (ADS)

Kim, Hyung Tae; Jeong, An Mok; Kim, Hyo Young; An, Jong Wook; Kim, Cheol Ho; Jin, Kyung Chan; Choi, Seung-Bok

2018-03-01

In a previous work, magneto-rheological (MR) dampers were originally designed and implemented for reducing the vertical low-frequency vibration occurring in precise semi-conductor manufacturing equipment. To reduce the vibrations, an isolator levitated the manufacturing machine from the floor using pneumatic pressure which cut off the external vibration, while the MR damper was used to decrease the transient response of the isolator. However, it has been found that the MR damper also provides a damping effect on the lateral vibration induced by the high-speed plane motions. Therefore, in this work both vertical and lateral vibrations are controlled using the yield and shear stresses of the lateral directions generated from the MR fluids by applying a magnetic field. After deriving a vibration control model, an overall control logic is formulated considering both vertical and lateral vibrations. In this control strategy, a feedback loop associated with the laser sensor is used for vertical vibration control, while a feed-forward loop with the motion information is used for lateral vibration control. The experimental results show that the proposed concept is highly effective for lateral vibration control using the damping effect on multiple directions.

Tape transport mechanism

DOEpatents

Groh, Edward F.; McDowell, William; Modjeski, Norbert S.; Keefe, Donald J.; Groer, Peter

1979-01-01

A device is provided for transporting, in a stepwise manner, tape between a feed reel and takeup reel. An indexer moves across the normal path of the tape displacing it while the tape on the takeup reel side of the indexer is braked. After displacement, the takeup reel takes up the displaced tape while the tape on the feed reel side of the indexer is braked, providing stepwise tape transport in precise intervals determined by the amount of displacement caused by the indexer.

Effects of pesticide applications and cultural controls on efficacy of control for adult Japanese beetles (Coleoptera: Scarabaeidae) on roses.

PubMed

Vitullo, Justin M; Sadof, Clifford S

2007-02-01

Cultural and chemical controls were evaluated to determine their ability to deter feeding by Japanese beetles, Popillia japonica Newman (Coleoptera: Scarabaeidae), on floribunda type roses, Rosa 'Acadia Sunrise'. Roses were arranged in field plots and exposed to resident adult beetle populations. Cultural controls were designed to block the feeding-induced aggregation response by manually removing beetles and/ or damaged blooms from rose plants. Azadirachtin, carbaryl, and imidacloprid were evaluated in field and laboratory trials. In no-choice laboratory assays, foliar applications of azadirachtin caused low rates of morbidity to adult beetles and were unable to deter feeding. Foliar-applied carbaryl and soil-applied imidacloprid caused high rates of morbidity and reduced feeding injury. In the field, foliar sprays of azadirachtin and carbaryl, deterred feeding on foliage under low beetle pressure (maximum of 29% defoliation in untreated controls), when applied weekly after first beetle flight or every 2 wk after 5% injury was reached. A single foliar application of these materials at the 5% injury level did not significantly reduce peak defoliation. Soil applications of imidacloprid also deterred foliar feeding in the field. Blooms were more difficult to protect with both foliar- and soil-applied insecticides with only weekly application of foliar insecticides providing significant reductions in bloom injury. Removing beetles and/or blooms provided marginally greater reductions in leaf and flower injury. This suggests that blocking the feeding-induced aggregation response of Japanese beetles can provide only modest levels of control in roses where both flowers and feeding-induced volatiles recruit beetles to plants.

A real-time surface inspection system for precision steel balls based on machine vision

NASA Astrophysics Data System (ADS)

Chen, Yi-Ji; Tsai, Jhy-Cherng; Hsu, Ya-Chen

2016-07-01

Precision steel balls are one of the most fundament components for motion and power transmission parts and they are widely used in industrial machinery and the automotive industry. As precision balls are crucial for the quality of these products, there is an urgent need to develop a fast and robust system for inspecting defects of precision steel balls. In this paper, a real-time system for inspecting surface defects of precision steel balls is developed based on machine vision. The developed system integrates a dual-lighting system, an unfolding mechanism and inspection algorithms for real-time signal processing and defect detection. The developed system is tested under feeding speeds of 4 pcs s-1 with a detection rate of 99.94% and an error rate of 0.10%. The minimum detectable surface flaw area is 0.01 mm2, which meets the requirement for inspecting ISO grade 100 precision steel balls.

Control of cerebellar granule cell output by sensory-evoked Golgi cell inhibition

PubMed Central

Duguid, Ian; Branco, Tiago; Chadderton, Paul; Arlt, Charlotte; Powell, Kate; Häusser, Michael

2015-01-01

Classical feed-forward inhibition involves an excitation–inhibition sequence that enhances the temporal precision of neuronal responses by narrowing the window for synaptic integration. In the input layer of the cerebellum, feed-forward inhibition is thought to preserve the temporal fidelity of granule cell spikes during mossy fiber stimulation. Although this classical feed-forward inhibitory circuit has been demonstrated in vitro, the extent to which inhibition shapes granule cell sensory responses in vivo remains unresolved. Here we combined whole-cell patch-clamp recordings in vivo and dynamic clamp recordings in vitro to directly assess the impact of Golgi cell inhibition on sensory information transmission in the granule cell layer of the cerebellum. We show that the majority of granule cells in Crus II of the cerebrocerebellum receive sensory-evoked phasic and spillover inhibition prior to mossy fiber excitation. This preceding inhibition reduces granule cell excitability and sensory-evoked spike precision, but enhances sensory response reproducibility across the granule cell population. Our findings suggest that neighboring granule cells and Golgi cells can receive segregated and functionally distinct mossy fiber inputs, enabling Golgi cells to regulate the size and reproducibility of sensory responses. PMID:26432880

An automatic pellet dispenser for precise control of feeding topography in granivorous birds

PubMed Central

Berkhoudt, H.; Van Der Reijden, D.; Heijmans, M.

1987-01-01

Design and construction of an automatic pellet dispenser for granivorous birds are described. The dispenser permits rapid pneumatic delivery of pellets (five pellets per second maximum) to one controlled position and does not interfere with simultaneous electrophysiological recording. In addition, the device continuously indicates presence or absence of a pellet in the delivery position. This automatic dispenser proved very effective in our studies of stereotyped topographies of feeding in granivorous birds, such as pigeons and chickens. PMID:16812503

Design of a novel automated methanol feed system for pilot-scale fermentation of Pichia pastoris.

PubMed

Hamaker, Kent H; Johnson, Daniel C; Bellucci, Joseph J; Apgar, Kristie R; Soslow, Sherry; Gercke, John C; Menzo, Darrin J; Ton, Christopher

2011-01-01

Large-scale fermentation of Pichia pastoris requires a large volume of methanol feed during the induction phase. However, a large volume of methanol feed is difficult to use in the processing suite because of the inconvenience of constant monitoring, manual manipulation steps, and fire and explosion hazards. To optimize and improve safety of the methanol feed process, a novel automated methanol feed system has been designed and implemented for industrial fermentation of P. pastoris. Details of the design of the methanol feed system are described. The main goals of the design were to automate the methanol feed process and to minimize the hazardous risks associated with storing and handling large quantities of methanol in the processing area. The methanol feed system is composed of two main components: a bulk feed (BF) system and up to three portable process feed (PF) systems. The BF system automatically delivers methanol from a central location to the portable PF system. The PF system provides precise flow control of linear, step, or exponential feed of methanol to the fermenter. Pilot-scale fermentations with linear and exponential methanol feeds were conducted using two Mut(+) (methanol utilization plus) strains, one expressing a recombinant therapeutic protein and the other a monoclonal antibody. Results show that the methanol feed system is accurate, safe, and efficient. The feed rates for both linear and exponential feed methods were within ± 5% of the set points, and the total amount of methanol fed was within 1% of the targeted volume. Copyright © 2011 American Institute of Chemical Engineers (AIChE).

The potential and biological test on cloned cassava crop remains on local sheep

NASA Astrophysics Data System (ADS)

Ginting, R.; Umar, S.; Hanum, C.

2018-02-01

This research aims at knowing the potential of cloned cassava crop remains dry matter and the impact of the feeding of the cloned cassava crop remains based complete feed on the consumption, the body weight gain, and the feed conversion of the local male sheep with the average of initial body weight of 7.75±1.75 kg. The design applied in the first stage research was random sampling method with two frames of tile and the second stage research applied Completely Randomized Design (CRD) with three (3) treatments and four (4) replicates. These treatments consisted of P1 (100% grass); P2 (50% grass, 50% complete feed pellet); P3 (100% complete feed from the raw material of cloned cassava crop remaining). Statistical tests showed that the feeding of complete feed whose raw material was from cloned cassava crop remains gave a highly significant impact on decreasing feed consumption, increasing body weight, lowering feed conversion, and increasing crude protein digestibility. The conclusion is that the cloned cassava crop remains can be used as complete sheep feed to replace green grass and can give the best result.

Livestock Nutrition and Feeding. Student Manual. Second Edition.

ERIC Educational Resources Information Center

Ridenour, Harlan E.

This manual is designed to help agricultural education students and teachers to apply scientific facts and principles to problem-solving procedures in determining nutritious and economical livestock feeding programs. The manual provides applied scientific activities in biological science and chemistry, mathematics, and communication skills. It…

Planar Laser Imaging of Scattering and Fluorescence of Zooplankton Feeding in Layers of Phytoplankton in situ

DTIC Science & Technology

2007-09-30

Planar Laser Imaging of Scattering and Fluorescence of Zooplankton Feeding in Layers of Phytoplankton in situ Peter J.S. Franks Scripps...herbivorous copepod feeding in the laboratory, and 2) to apply these methods in the field to observe the dynamics of copepod feeding in situ. In...particular we intend to test the “ feeding sorties” hypothesis vs. the “in situ feeding ” hypothesis regarding the location and timing of copepod feeding

A modular assembling platform for manufacturing of microsystems by optical tweezers

NASA Astrophysics Data System (ADS)

Ksouri, Sarah Isabelle; Aumann, Andreas; Ghadiri, Reza; Prüfer, Michael; Baer, Sebastian; Ostendorf, Andreas

2013-09-01

Due to the increased complexity in terms of materials and geometries for microsystems new assembling techniques are required. Assembling techniques from the semiconductor industry are often very specific and cannot fulfill all specifications in more complex microsystems. Therefore, holographic optical tweezers are applied to manipulate structures in micrometer range with highest flexibility and precision. As is well known non-spherical assemblies can be trapped and controlled by laser light and assembled with an additional light modulator application, where the incident laser beam is rearranged into flexible light patterns in order to generate multiple spots. The complementary building blocks are generated by a two-photon-polymerization process. The possibilities of manufacturing arbitrary microstructures and the potential of optical tweezers lead to the idea of combining manufacturing techniques with manipulation processes to "microrobotic" processes. This work presents the manipulation of generated complex microstructures with optical tools as well as a storage solution for 2PP assemblies. A sample holder has been developed for the manual feeding of 2PP building blocks. Furthermore, a modular assembling platform has been constructed for an `all-in-one' 2PP manufacturing process as a dedicated storage system. The long-term objective is the automation process of feeding and storage of several different 2PP micro-assemblies to realize an automated assembly process.

Modeling and control of a dielectric elastomer actuator

NASA Astrophysics Data System (ADS)

Gupta, Ujjaval; Gu, Guo-Ying; Zhu, Jian

2016-04-01

The emerging field of soft robotics offers the prospect of applying soft actuators as artificial muscles in the robots, replacing traditional actuators based on hard materials, such as electric motors, piezoceramic actuators, etc. Dielectric elastomers are one class of soft actuators, which can deform in response to voltage and can resemble biological muscles in the aspects of large deformation, high energy density and fast response. Recent research into dielectric elastomers has mainly focused on issues regarding mechanics, physics, material designs and mechanical designs, whereas less importance is given to the control of these soft actuators. Strong nonlinearities due to large deformation and electromechanical coupling make control of the dielectric elastomer actuators challenging. This paper investigates feed-forward control of a dielectric elastomer actuator by using a nonlinear dynamic model. The material and physical parameters in the model are identified by quasi-static and dynamic experiments. A feed-forward controller is developed based on this nonlinear dynamic model. Experimental evidence shows that this controller can control the soft actuator to track the desired trajectories effectively. The present study confirms that dielectric elastomer actuators are capable of being precisely controlled with the nonlinear dynamic model despite the presence of material nonlinearity and electromechanical coupling. It is expected that the reported results can promote the applications of dielectric elastomer actuators to soft robots or biomimetic robots.

Promotion and advocacy for improved complementary feeding: can we apply the lessons learned from breastfeeding?

PubMed

Piwoz, Ellen G; Huffman, Sandra L; Quinn, Victoria J

2003-03-01

Although many successes have been achieved in promoting breastfeeding, this has not been the case for complementary feeding. Some successes in promoting complementary feeding at the community level have been documented, but few of these efforts have expanded to a larger scale and become sustained. To discover the reasons for this difference, the key factors for the successful promotion of breastfeeding on a large scale were examined and compared with the efforts made in complementary feeding. These factors include definition and rationale, policy support, funding, advocacy, private-sector involvement, availability and use of monitoring data, integration of research into action, and the existence of a well-articulated series of steps for successful implementation. The lessons learned from the promotion of breastfeeding should be applied to complementary feeding, and the new Global Strategy for Infant and Young Child Feeding provides an excellent first step in this process.

How Nectar-Feeding Bats Localize their Food: Echolocation Behavior of Leptonycteris yerbabuenae Approaching Cactus Flowers

PubMed Central

Koblitz, Jens C.; Fleming, Theodore H.; Medellín, Rodrigo A.; Kalko, Elisabeth K. V.; Schnitzler, Hans-Ulrich; Tschapka, Marco

2016-01-01

Nectar-feeding bats show morphological, physiological, and behavioral adaptations for feeding on nectar. How they find and localize flowers is still poorly understood. While scent cues alone allow no precise localization of a floral target, the spatial properties of flower echoes are very precise and could play a major role, particularly at close range. The aim of this study is to understand the role of echolocation for classification and localization of flowers. We compared the approach behavior of Leptonycteris yerbabuenae to flowers of a columnar cactus, Pachycereus pringlei, to that to an acrylic hollow hemisphere that is acoustically conspicuous to bats, but has different acoustic properties and, contrary to the cactus flower, present no scent. For recording the flight and echolocation behaviour we used two infrared video cameras under stroboscopic illumination synchronized with ultrasound recordings. During search flights all individuals identified both targets as a possible food source and initiated an approach flight; however, they visited only the cactus flower. In experiments with the acrylic hemisphere bats aborted the approach at ca. 40–50 cm. In the last instant before the flower visit the bats emitted a long terminal group of 10–20 calls. This is the first report of this behaviour for a nectar-feeding bat. Our findings suggest that L. yerbabuenae use echolocation for classification and localization of cactus flowers and that the echo-acoustic characteristics of the flower guide the bats directly to the flower opening. PMID:27684373

Method for controlling gas metal arc welding

DOEpatents

Smartt, Herschel B.; Einerson, Carolyn J.; Watkins, Arthur D.

1989-01-01

The heat input and mass input in a Gas Metal Arc welding process are controlled by a method that comprises calculating appropriate values for weld speed, filler wire feed rate and an expected value for the welding current by algorithmic function means, applying such values for weld speed and filler wire feed rate to the welding process, measuring the welding current, comparing the measured current to the calculated current, using said comparison to calculate corrections for the weld speed and filler wire feed rate, and applying corrections.

21 CFR 1.377 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-04-01

..., fruits, vegetables, fish, dairy products, eggs, raw agricultural commodities for use as food or components of food, animal feed, including pet food, food and feed ingredients and additives, including... 21 Food and Drugs 1 2010-04-01 2010-04-01 false What definitions apply to this subpart? 1.377...

Assessing impacts of land-applied manure from concentrated animal feeding operations on fish populations and communities

EPA Science Inventory

Concentrated animal feeding operation (CAFO) waste is a cost effective fertilizer. In the Midwest, networks of subsurface tile-drains expedite transport of animal hormones and nutrients from land-applied CAFO waste to adjacent waterways. The objective of this study was to evaluat...

Effect of diet composition and incubation time on feed indigestible neutral detergent fiber concentration in dairy cows.

PubMed

Krizsan, S J; Huhtanen, P

2013-03-01

Indigestible neutral detergent fiber (NDF) predicts forage digestibility accurately and precisely when determined by a 288-h ruminal in situ incubation, and it is an important parameter in mechanistic rumen models. The long incubation time required is a disadvantage. Further, intrinsic cell wall characteristics of feeds should be determined under ideal conditions for fiber digestion. The objective of this study was to determine the effects of diet composition and rumen incubation time on the concentrations of indigestible NDF (iNDF) for a wide range of feeds in dairy cows. Additionally, predicted concentrations of unavailable NDF generated using the National Research Council (NRC) model and the Cornell Net Carbohydrate and Protein System (CNCPS) were evaluated. Indigestible NDF was evaluated in 18 feeds using 4 cows in a split-split plot design. Treatments were in a 3 × 3 factorial arrangement, consisting of different diets and incubation times. Diet composition was primarily varied by changing the level of concentrate supplementation between 190 (low), 421 (medium), and 625 (high)g/kg of diet dry matter (DM). Grass silage was used as the basal forage for all cows. The feeds were incubated for 144, 216, and 288 h. Indigestible NDF was determined from 2-g samples weighed into polyester bags with a pore size of 12 µm and a pore area equal to 6% of the total surface area, giving a sample size to surface ratio of 10mg/cm(2). Across all feeds, the measured iNDF concentrations ranged from 6 to 516 g/kg of DM. The feed iNDF concentration was not affected by the cow used, but diet composition had a significant effect. The mean measured iNDF concentrations for cows consuming low-, medium-, and high-concentrate diets were 178, 186, and 197 g/kg of DM, respectively. The incubation time also affected the feed iNDF concentrations, which averaged 199, 185, and 177 g/kg of DM for 144-, 216-, and 288-h incubations, respectively. We also observed significant interactions between incubation time and feed, and between diet composition and feed, with fiber-rich feeds being most sensitive to these factors. The evaluation of model predictions of unavailable NDF indicated poor precision with prediction errors of 56 (NRC) and 84 (CNCPS)g/kg of DM. Indigestible NDF should be determined based on 288-h ruminal in situ incubations in cows consuming diets with a low proportion of concentrate to represent the feed fraction that is unavailable to the animal. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Simulation to coating weight control for galvanizing

NASA Astrophysics Data System (ADS)

Wang, Junsheng; Yan, Zhang; Wu, Kunkui; Song, Lei

2013-05-01

Zinc coating weight control is one of the most critical issues for continuous galvanizing line. The process has the characteristic of variable-time large time delay, nonlinear, multivariable. It can result in seriously coating weight error and non-uniform coating. We develop a control system, which can automatically control the air knives pressure and its position to give a constant and uniform zinc coating, in accordance with customer-order specification through an auto-adaptive empirical model-based feed forward adaptive controller, and two model-free adaptive feedback controllers . The proposed models with controller were applied to continuous galvanizing line (CGL) at Angang Steel Works. By the production results, the precise and stability of the control model reduces over-coating weight and improves coating uniform. The product for this hot dip galvanizing line does not only satisfy the customers' quality requirement but also save the zinc consumption.

Non-stationary time series modeling on caterpillars pest of palm oil for early warning system

NASA Astrophysics Data System (ADS)

Setiyowati, Susi; Nugraha, Rida F.; Mukhaiyar, Utriweni

2015-12-01

The oil palm production has an important role for the plantation and economic sector in Indonesia. One of the important problems in the cultivation of oil palm plantation is pests which causes damage to the quality of fruits. The caterpillar pest which feed palm tree's leaves will cause decline in quality of palm oil production. Early warning system is needed to minimize losses due to this pest. Here, we applied non-stationary time series modeling, especially the family of autoregressive models to predict the number of pests based on its historical data. We realized that there is some uniqueness of these pests data, i.e. the spike value that occur almost periodically. Through some simulations and case study, we obtain that the selection of constant factor has a significance influence to the model so that it can shoot the spikes value precisely.

Comparison study of two procedures for the determination of emamectin benzoate in medicated fish feed.

PubMed

Farer, Leslie J; Hayes, John M

2005-01-01

A new method has been developed for the determination of emamectin benzoate in fish feed. The method uses a wet extraction, cleanup by solid-phase extraction, and quantitation and separation by liquid chromatography (LC). In this paper, we compare the performance of this method with that of a previously reported LC assay for the determination of emamectin benzoate in fish feed. Although similar to the previous method, the new procedure uses a different sample pretreatment, wet extraction, and quantitation method. The performance of the new method was compared with that of the previously reported method by analyses of 22 medicated feed samples from various commercial sources. A comparison of the results presented here reveals slightly lower assay values obtained with the new method. Although a paired sample t-test indicates the difference in results is significant, this difference is within the method precision of either procedure.

Preparation of pentacene thin film deposited using organic material auto-feeding system for the fabrication of organic thin film transistor.

PubMed

Kim, Young Baek; Choi, Bum Ho; Lim, Yong Hwan; Yoo, Ha Na; Lee, Jong Ho; Kim, Jin Hyeok

2011-02-01

In this study, pentacene organic thin film was prepared using newly developed organic material auto-feeding system integrated with linear cell and characterized. The newly developed organic material auto-feeding system consists of 4 major parts: reservoir, micro auto-feeder, vaporizer, and linear cell. The deposition of organic thin film could be precisely controlled by adjusting feeding rate, main tube size, position and size of nozzle. 10 nm thick pentacene thin film prepared on glass substrate exhibited high uniformity of 3.46% which is higher than that of conventional evaporation method using point cell. The continuous deposition without replenishment of organic material can be performed over 144 hours with regulated deposition control. The grain size of pentacene film which affect to mobility of OTFT, was controlled as a function of the temperature.

High Dielectric Low Loss Transparent Glass Material Based Dielectric Resonator Antenna with Wide Bandwidth Operation

NASA Astrophysics Data System (ADS)

Mehmood, Arshad; Zheng, Yuliang; Braun, Hubertus; Hovhannisyan, Martun; Letz, Martin; Jakoby, Rolf

2015-01-01

This paper presents the application of new high permittivity and low loss glass material for antennas. This glass material is transparent. A very simple rectangular dielectric resonator antenna is designed first with a simple microstrip feeding line. In order to widen the bandwidth, the feed of the design is modified by forming a T-shaped feeding. This new design enhanced the bandwidth range to cover the WLAN 5 GHz band completely. The dielectric resonator antenna cut into precise dimensions is placed on the modified microstrip feed line. The design is simple and easy to manufacture and also very compact in size of only 36 × 28 mm. A -10 dB impedance bandwidth of 18% has been achieved, which covers the frequency range from 5.15 GHz to 5.95 GHz. Simulations of the measured return loss and radiation patterns are presented and discussed.

Feeding modes in stream salmonid population models: Is drift feeding the whole story?

Treesearch

Bret Harvey; Steve Railsback

2014-01-01

Drift-feeding models are essential components of broader models that link stream habitat to salmonid populations and community dynamics. But is an additional feeding mode needed for understanding and predicting salmonid population responses to streamflow and other environmental factors? We addressed this question by applying two versions of the individual-based model...

Application of Prebiotics and Probiotics in Livestock

NASA Astrophysics Data System (ADS)

Collins, James W.; La Ragione, Roberto M.; Woodward, Martin J.; Searle, Laura E. J.

The advent of antibiotics and their use for treatment of clinical manifestations of infections has had a profound impact on animal health and welfare. In addition to direct application in the control of infection, low concentrations of antibiotics given in animal feed has been shown to correlate with higher health status and improved performance in terms of feed conversion (productive weight gain). Thus it is that antibiotics have been used as “growth promoters” in feed for livestock since the 1940s (Cromwell, 2001). Since the inception of this growth promotion concept there has been a debate on precisely how low level antibiotics mediate their action and whether or not this contributes to the acquisition of resistance in the bacterial flora of livestock.

A method for including external feed in depletion calculations with CRAM and implementation into ORIGEN

DOE PAGES

Isotalo, Aarno E.; Wieselquist, William A.

2015-05-15

A method for including external feed with polynomial time dependence in depletion calculations with the Chebyshev Rational Approximation Method (CRAM) is presented and the implementation of CRAM to the ORIGEN module of the SCALE suite is described. In addition to being able to handle time-dependent feed rates, the new solver also adds the capability to perform adjoint calculations. Results obtained with the new CRAM solver and the original depletion solver of ORIGEN are compared to high precision reference calculations, which shows the new solver to be orders of magnitude more accurate. Lastly, in most cases, the new solver is upmore » to several times faster due to not requiring similar substepping as the original one.« less

KSC-08pd0040

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- Mike Berger, with Lockheed Martin, examines the replacement feed-through connector for the engine cutoff, or ECO, sensor system in space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

KSC-08pd0043

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- Lloyd Johns, with Lockheed Martin, attaches the replacement feed-through connector in the engine cutoff, or ECO, sensor system to the internal connector on space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

KSC-08pd0044

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- Lloyd Johns, with Lockheed Martin, attaches the replacement feed-through connector in the engine cutoff, or ECO, sensor system to the internal connector on space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

KSC-08pd0041

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- This closeup of the replacement feed-through connector for the engine cutoff, or ECO, sensor system on space shuttle Atlantis shows the pins that were soldered at Kennedy. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

Review: Milking robot utilization, a successful precision livestock farming evolution.

PubMed

John, A J; Clark, C E F; Freeman, M J; Kerrisk, K L; Garcia, S C; Halachmi, I

2016-09-01

Automatic milking systems (AMS), one of the earliest precision livestock farming developments, have revolutionized dairy farming around the world. While robots control the milking process, there have also been numerous changes to how the whole farm system is managed. Milking is no longer performed in defined sessions; rather, the cow can now choose when to be milked in AMS, allowing milking to be distributed throughout a 24 h period. Despite this ability, there has been little attention given to milking robot utilization across 24 h. In order to formulate relevant research questions and improve farm AMS management there is a need to determine the current knowledge gaps regarding the distribution of robot utilization. Feed, animal and management factors and their interplay on levels of milking robot utilization across 24 h for both indoor and pasture-based systems are here reviewed. The impact of the timing, type and quantity of feed offered and their interaction with the distance of feed from the parlour; herd social dynamics, climate and various other management factors on robot utilization through 24 h are provided. This novel review draws together both the opportunities and challenges that exist for farm management to use these factors to improved system efficiency and those that exist for further research.

Method for controlling gas metal arc welding

DOEpatents

Smartt, H.B.; Einerson, C.J.; Watkins, A.D.

1987-08-10

The heat input and mass input in a Gas Metal Arc welding process are controlled by a method that comprises calculating appropriate values for weld speed, filler wire feed rate and an expected value for the welding current by algorithmic function means, applying such values for weld speed and filler wire feed rate to the welding process, measuring the welding current, comparing the measured current to the calculated current, using said comparison to calculate corrections for the weld speed and filler wire feed rate, and applying corrections. 3 figs., 1 tab.

A precision mechanical nerve stimulator

NASA Technical Reports Server (NTRS)

Tcheng, Ping; Supplee, Frank H., Jr.; Prass, Richard L.

1988-01-01

An electromechanical device, used to apply and monitor stimulating pulses to a mammalian motor nerve, has been successfully developed at NASA Langley Research Center. Two existing force transducers, a flight skin friction balance and a miniature skin friction balance which were designed for making aerodynamic drag measurements, were modified and incorporated to form this precision instrument. The nerve stimulator is a type one servomechanism capable of applying and monitoring stimulating pulses of 0 to 10 grams with a precision of better than +/- 0.05 grams. Additionally, the device can be independently used to apply stimulating pulses by displacing the nerve from 0 to 0.25 mm with a precision of better than +/- 0.001 mm while measuring the level of the load applied.

Nomenclature of nearctic conifer-feeding choristoneura (Lepidoptera: tortricidae): historical review and present status.

Treesearch

Jerry A. Powell

1980-01-01

There have been 18 species-group names proposed for Nearctic conifer-feeding moths in the genus Choristoneura. Of these, houstonana (Grote) and its synonym, retana (Walsingham), apply to Cupressaceae-feeding populations now assigned to Cudonigera Obraztsov & Powell. The remaining...

Aspects of ultra-high-precision diamond machining of RSA 443 optical aluminium

NASA Astrophysics Data System (ADS)

Mkoko, Z.; Abou-El-Hossein, K.

2015-08-01

Optical aluminium alloys such as 6061-T6 are traditionally used in ultra-high precision manufacturing for making optical mirrors for aerospace and other applications. However, the optics industry has recently witnessed the development of more advanced optical aluminium grades that are capable of addressing some of the issues encountered when turning with single-point natural monocrystalline diamond cutters. The advent of rapidly solidified aluminium (RSA) grades has generally opened up new possibilities for ultra-high precision manufacturing of optical components. In this study, experiments were conducted with single-point diamond cutters on rapidly solidified aluminium RSA 443 material. The objective of this study is to observe the effects of depth of cut and feed rate at a fixed rotational speed on the tool wear rate and resulting surface roughness of diamond turned specimens. This is done to gain further understanding of the rate of wear on the diamond cutters versus the surface texture generated on the RSA 443 material. The diamond machining experiments yielded machined surfaces which are less reflective but with consistent surface roughness values. Cutting tools were observed for wear through scanning microscopy; relatively low wear pattern was evident on the diamond tool edge. The highest tool wear were obtained at higher depth of cut and increased feed rate.

Development of an LC-MS/MS analytical method for the simultaneous measurement of aldehydes from polyunsaturated fatty acids degradation in animal feed.

PubMed

Douny, Caroline; Bayram, Pinar; Brose, François; Degand, Guy; Scippo, Marie-Louise

2016-05-01

Knowing that polyunsaturated fatty acids can lead to the formation of potentially toxic aldehydes as secondary oxidation products, an analytical method using liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) detection was developed to measure the concentration of eight aldehydes in animal feed: malondialdehyde (MDA), 4-hydroxy-2-nonenal (4-HNE), 4-hydroxy-2-hexenal (4-HHE), crotonaldehyde (CRT), benzaldehyde (BNZ), hexanal (HXL), 2,4-nonadienal, and 2,4-decadienal. The developed method was validated according to the criteria and procedure described in international standards. The evaluated parameters were specificity/selectivity, recovery, precision, accuracy, uncertainty, limits of detection and quantification, using the concept of accuracy profiles. These parameters were determined during experiments conducted over three different days with ground Kellogg's® Corn Flakes® cereals as model matrix for animal feed and spiked at different levels of concentration. Malondialdehyde, 4-HHE, 4-HNE, crotonaldehyde, benzaldehyde, and hexanal can be analyzed in the same run in animal feed with a very good accuracy, with recovery rates ranging from 86 to 109% for a working range going from 0.16 to 12.50 mg/kg. The analysis of 2,4-nonadienal and 2,4-decadienal can also be performed but in a limited range of concentration and with a limited degree of accuracy. Their recovery rates ranged between 54 and 114% and coefficient of variation for the intermediate precision between 11 and 25% for these two compounds. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Creep feeding nursing beef calves.

PubMed

Lardy, Gregory P; Maddock, Travis D

2007-03-01

Creep feeding can be used to increase calf weaning weights. However, the gain efficiency of free-choice, energy-based creep feeds is relatively poor. Generally, limit-feeding, high-protein creep feeds are more efficient, and gains may be similar to those produced by creep feeds offered free choice. Creep feeding can increase total organic matter intake and improve the overall energy status of the animal. Creep-fed calves tend to acclimate to the feedlot more smoothly than unsupplemented calves. Furthermore, provision of a high-starch creep feed may have a positive influence on subsequent carcass quality traits. Creep feeding can be applied to numerous environmental situations to maximize calf performance; however, beef cattle producers should consider their individual situations carefully before making the decision to creep feed.

Planar Laser Imaging of Scattering and Fluorescence of Zooplankton Feeding in Layers of Phytoplankton in situ

DTIC Science & Technology

2010-09-30

planktonic ecosystems. OBJECTIVES Our objectives in this work are to 1) visualize and quantify herbivorous copepod feeding in the laboratory...and 2) to apply these methods in the field to observe the dynamics of copepod feeding in situ. In particular we intend to test the “feeding sorties...hypothesis vs. the “in situ feeding” hypothesis regarding the location and timing of copepod feeding and vertical migration. APPROACH Previous

Feeding Experimentation Device (FED): A flexible open-source device for measuring feeding behavior.

PubMed

Nguyen, Katrina P; O'Neal, Timothy J; Bolonduro, Olurotimi A; White, Elecia; Kravitz, Alexxai V

2016-07-15

Measuring food intake in rodents is a conceptually simple yet labor-intensive and temporally-imprecise task. Most commonly, food is weighed manually, with an interval of hours or days between measurements. Commercial feeding monitors are excellent, but are costly and require specialized caging and equipment. We have developed the Feeding Experimentation Device (FED): a low-cost, open-source, home cage-compatible feeding system. FED utilizes an Arduino microcontroller and open-source software and hardware. FED dispenses a single food pellet into a food well where it is monitored by an infrared beam. When the mouse removes the pellet, FED logs the timestamp to a secure digital (SD) card and dispenses a new pellet into the well. Post-hoc analyses of pellet retrieval timestamps reveal high-resolution details about feeding behavior. FED is capable of accurately measuring food intake, identifying discrete trends during light and dark-cycle feeding. Additionally, we show the utility of FED for measuring increases in feeding resulting from optogenetic stimulation of agouti-related peptide neurons in the arcuate nucleus of the hypothalamus. With a cost of ∼$350 per device, FED is >10× cheaper than commercially available feeding systems. FED is also self-contained, battery powered, and designed to be placed in standard colony rack cages, allowing for monitoring of true home cage feeding behavior. Moreover, FED is highly adaptable and can be synchronized with emerging techniques in neuroscience, such as optogenetics, as we demonstrate here. FED allows for accurate, precise monitoring of feeding behavior in a home cage setting. Published by Elsevier B.V.

Deoxynivalenol, zearalenone and T-2 in grain based swine feed in Hungary.

PubMed

Tima, Helga; Rácz, Anita; Guld, Zsuzsanna; Mohácsi-Farkas, Csilla; Kiskó, Gabriella

2016-12-01

Fusarium genera can produce trichothecenes like deoxynivalenol (DON), zearalenone (ZEN) and T-2 toxin, which can occur in feed cereal grains. Enzyme-linked immunosorbent assays (ELISA) tests of different Hungarian swine feedstuff proved that these mycotoxins were present. In this survey, 45 feed samples from 3 significant Hungarian swine feedstuff manufacturers were tested. ELISA methodology validation showed mean recovery rates in ranges from 85.3% to 98.1%, with intermediate precision of 86.9-96.9% and variation coefficients of 3.4-5.7% and 5.9-7.1%, respectively. The results showed that among Fusarium toxins, generally DON was present in the highest concentration, followed by T-2 and finally ZEN in all tested swine feeds. Each of the mycotoxins was found above the limit of detection in all swine feedstuffs. Boars feed's DON (average ± standard deviation was 872 ± 139 µg kg -1 ) and ZEN (172 ± 18 µg kg -1 ) results of one of the manufacturers were above the guidance values. It indicates the necessity for efficient monitoring of DON, ZEN and T-2 mycotoxins in swine feeds.

Mycotoxin Contamination in the EU Feed Supply Chain: A Focus on Cereal Byproducts.

PubMed

Pinotti, Luciano; Ottoboni, Matteo; Giromini, Carlotta; Dell'Orto, Vittorio; Cheli, Federica

2016-02-15

Mycotoxins represent a risk to the feed supply chain with an impact on economies and international trade. A high percentage of feed samples have been reported to be contaminated with more than one mycotoxin. In most cases, the concentrations were low enough to ensure compliance with the European Union (EU) guidance values or maximum admitted levels. However, mycotoxin co-contamination might still exert adverse effects on animals due to additive/synergistic interactions. Studies on the fate of mycotoxins during cereal processing, such as milling, production of ethanol fuels, and beer brewing, have shown that mycotoxins are concentrated into fractions that are commonly used as animal feed. Published data show a high variability in mycotoxin repartitioning, mainly due to the type of mycotoxins, the level and extent of fungal contamination, and a failure to understand the complexity of food processing technologies. Precise knowledge of mycotoxin repartitioning during technological processes is critical and may provide a sound technical basis for feed managers to conform to legislation requirements and reduce the risk of severe adverse market and trade repercussions. Regular, economical and straightforward feed testing is critical to reach a quick and accurate diagnosis of feed quality. The use of rapid methods represents a future challenge.

Mycotoxin Contamination in the EU Feed Supply Chain: A Focus on Cereal Byproducts

PubMed Central

Pinotti, Luciano; Ottoboni, Matteo; Giromini, Carlotta; Dell’Orto, Vittorio; Cheli, Federica

2016-01-01

Mycotoxins represent a risk to the feed supply chain with an impact on economies and international trade. A high percentage of feed samples have been reported to be contaminated with more than one mycotoxin. In most cases, the concentrations were low enough to ensure compliance with the European Union (EU) guidance values or maximum admitted levels. However, mycotoxin co-contamination might still exert adverse effects on animals due to additive/synergistic interactions. Studies on the fate of mycotoxins during cereal processing, such as milling, production of ethanol fuels, and beer brewing, have shown that mycotoxins are concentrated into fractions that are commonly used as animal feed. Published data show a high variability in mycotoxin repartitioning, mainly due to the type of mycotoxins, the level and extent of fungal contamination, and a failure to understand the complexity of food processing technologies. Precise knowledge of mycotoxin repartitioning during technological processes is critical and may provide a sound technical basis for feed managers to conform to legislation requirements and reduce the risk of severe adverse market and trade repercussions. Regular, economical and straightforward feed testing is critical to reach a quick and accurate diagnosis of feed quality. The use of rapid methods represents a future challenge. PMID:26891326

Bone mineral content and density of the lumbar spine of infants and toddlers: influence of age, sex, race, growth, and human milk feeding.

PubMed

Kalkwarf, Heidi J; Zemel, Babette S; Yolton, Kimberly; Heubi, James E

2013-01-01

Little is known about factors that affect bone mass and density of infants and toddlers and the means to assess their bone health owing to challenges in studying this population. The objectives of this study were to describe age, sex, race, growth, and human milk feeding effects on bone mineral content (BMC) and areal density (aBMD) of the lumbar spine, and determine precision of BMC and aBMD measurements. We conducted a cross-sectional study of 307 healthy participants (63 black), ages 1 to 36 months. BMC and aBMD of the lumbar spine were measured by dual-energy X-ray absorptiometry. Duplicate scans were obtained on 76 participants for precision determination. Age-specific Z-scores for aBMD, weight, and length (BMDZ, WAZ, LAZ) were calculated. Information on human milk feeding duration was ascertained by questionnaire. Between ages 1 and 36 months, lumbar spine BMC increased about fivefold and aBMD increased twofold (p < 0.0001). BMC was greater (5.8%) in males than in females (p = 0.001), but there was no difference in aBMD (p = 0.37). There was no difference in BMC or aBMD between whites and blacks (p ≥ 0.16). WAZ and LAZ were positively associated with BMDZ (r = 0.34 and 0.24, p < 0.001). Duration of human milk feeding was negatively associated with BMDZ in infants <12 months of age (r = -0.42, p < 0.001). Precision of BMC and aBMD measurements was good, 2.20% and 1.84%, respectively. Dramatic increases in BMC and aBMD of the lumbar spine occur in the first 36 months of life. We provide age-specific values for aBMD of healthy infants and toddlers that can be used to evaluate bone deficits. Future studies are needed to identify the age when sex and race differences in aBMD occur, and how best to account for delayed or accelerated growth in the context of bone health assessment of infants and toddlers. Copyright © 2013 American Society for Bone and Mineral Research.

KSC-08pd0038

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- This closeup shows the internal connector to which the replacement feed-through connector in the engine cutoff, or ECO, sensor system on space shuttle Atlantis' external tank will be installed. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

KSC-08pd0045

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- Ray Clark, a Lockheed Martin engineer, completes attaching the replacement feed-through connector in the engine cutoff, or ECO, sensor system to the internal connector on space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

KSC-08pd0042

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- Jim Davis, a NASA quality inspector, examines the internal connector on space shuttle Atlantis' external tank to which the replacement feed-through connector in the engine cutoff, or ECO, sensor system will be attached. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

Determination of melamine in animal feed based on liquid chromatography tandem mass spectrometry analysis and dynamic microwave-assisted extraction coupled on-line with strong cation-exchange resin clean-up.

PubMed

Chen, Ligang; Zeng, Qinglei; Du, Xiaobo; Sun, Xin; Zhang, Xiaopan; Xu, Yang; Yu, Aimin; Zhang, Hanqi; Ding, Lan

2009-11-01

In this work, a new method was developed for the determination of melamine (MEL) in animal feed. The method was based on the on-line coupling of dynamic microwave-assisted extraction (DMAE) to strong cation-exchange (SCX) resin clean-up. The MEL was first extracted by 90% acidified methanol aqueous solution (v/v, pH = 3) under the action of microwave energy, and then the extract was cooled and passed through the SCX resin. Thus, the protonated MEL was retained on the resin through ion exchange interaction and the sample matrixes were washed out. Some obvious benefits were achieved, such as acceleration of analytical process, together with reduction in manual handling, risk of contamination, loss of analyte, and sample consumption. Finally, the analyte was separated by a liquid chromatograph with a SCX analytical column, and then identified and quantitatived by a tandem mass spectrometry with positive ionization mode and multiple-reaction monitoring. The DMAE parameters were optimized by the Box-Behnken design. The linearity of quantification obtained by analyzing matrix-matched standards is in the range of 50-5,000 ng g(-1). The limit of detection and limit of quantification obtained are 12.3 and 41.0 ng g(-1), respectively. The mean intra- and inter-day precisions expressed as relative standard deviations with three fortified levels (50, 250, and 500 ng g(-1)) are 5.1% and 7.3%, respectively, and the recoveries of MEL are in the range of 76.1-93.5%. The proposed method was successfully applied to determine MEL in different animal feeds obtained from the local market. MEL was detectable with the contents of 279, 136, and 742 ng g(-1) in three samples.

Cylindrical Asymmetrical Capacitors for Use in Outer Space

NASA Technical Reports Server (NTRS)

Campbell, Jonathan W.

2007-01-01

A report proposes that cylindrical asymmetrical capacitors (CACs) be used to generate small thrusts for precise maneuvering of spacecraft on long missions. The report notes that it has been known for decades that when high voltages are applied to CACs in air, thrusts are generated - most likely as a result of ionization of air molecules and acceleration of the ions by the high electric fields. The report goes on to discuss how to optimize the designs of CACs for operation as thrusters in outer space. Components that could be used to enable outerspace operation include a supply of gas and a shroud, partly surrounding a CAC, into which the gas would flow. Other elements of operation and design discussed in the report include variation of applied voltage and/or of gas flow to vary thrust, effects of CAC and shroud dimensions on thrust and weight, some representative electrode configurations, and several alternative designs, including one in which the basic CAC configuration would be modified into something shaped like a conventional rocket engine with converging/diverging nozzle and an anode with gas feed in the space that, in a conventional rocket engine, would be the combustion chamber.

Water Contaminant Mitigation in Ionic Liquid Propellant

NASA Technical Reports Server (NTRS)

Conroy, David; Ziemer, John

2009-01-01

Appropriate system and operational requirements are needed in order to ensure mission success without unnecessary cost. Purity requirements applied to thruster propellants may flow down to materials and operations as well as the propellant preparation itself. Colloid electrospray thrusters function by applying a large potential to a room temperature liquid propellant (such as an ionic liquid), inducing formation of a Taylor cone. Ions and droplets are ejected from the Taylor cone and accelerated through a strong electric field. Electrospray thrusters are highly efficient, precise, scaleable, and demonstrate low thrust noise. Ionic liquid propellants have excellent properties for use as electrospray propellants, but can be hampered by impurities, owing to their solvent capabilities. Of foremost concern is the water content, which can result from exposure to atmosphere. Even hydrophobic ionic liquids have been shown to absorb water from the air. In order to mitigate the risks of bubble formation in feed systems caused by water content of the ionic liquid propellant, physical properties of the ionic liquid EMI-Im are analyzed. The effects of surface tension, material wetting, physisorption, and geometric details of the flow manifold and electrospray emitters are explored. Results are compared to laboratory test data.

AE Monitoring of Diamond Turned Rapidly Soldified Aluminium 443

NASA Astrophysics Data System (ADS)

Onwuka, G.; Abou-El-Hossein, K.; Mkoko, Z.

2017-05-01

The fast replacement of conventional aluminium with rapidly solidified aluminium alloys has become a noticeable trend in the current manufacturing industries involved in the production of optics and optical molding inserts. This is as a result of the improved performance and durability of rapidly solidified aluminium alloys when compared to conventional aluminium. Melt spinning process is vital for manufacturing rapidly solidified aluminium alloys like RSA 905, RSA 6061 and RSA 443 which are common in the industries today. RSA 443 is a newly developed alloy with few research findings and huge research potential. There is no available literature focused on monitoring the machining of RSA 443 alloys. In this research, Acoustic Emission sensing technique was applied to monitor the single point diamond turning of RSA 443 on an ultrahigh precision lathe machine. The machining process was carried out after careful selection of feed, speed and depths of cut. The monitoring process was achieved with a high sampling data acquisition system using different tools while concurrent measurement of the surface roughness and tool wear were initiated after covering a total feed distance of 13km. An increasing trend of raw AE spikes and peak to peak signal were observed with an increase in the surface roughness and tool wear values. Hence, acoustic emission sensing technique proves to be an effective monitoring method for the machining of RSA 443 alloy.

Compact and Integrated Liquid Bismuth Propellant Feed System

NASA Technical Reports Server (NTRS)

Polzin, Kurt A.; Stanojev, Boris; Korman, Valentin; Gross, Jeffrey T.

2007-01-01

Operation of Hall thrusters with bismuth propellant has been shown to be a promising path toward high-power, high-performance, long-lifetime electric propulsion for spaceflight missions [1]. There has been considerable effort in the past three years aimed at resuscitating this promising technology and validating earlier experimental results indicating the advantages of a bismuth-fed Hall thruster. A critical element of the present effort is the precise metering of propellant to the thruster, since performance cannot be accurately assessed without an accurate accounting of mass flow rate. Earlier work used a pre./post-test propellant weighing scheme that did not provide any real-time measurement of mass flow rate while the thruster was firing, and makes subsequent performance calculations difficult. The motivation of the present work is to develop a precision liquid bismuth Propellant Management System (PMS) that provides hot, molten bismuth to the thruster while simultaneously monitoring in real-time the propellant mass flow rate. The system is a derivative of our previous propellant feed system [2], but the present system represents a more compact design. In addition, all control electronics are integrated into a single unit and designed to reside on a thrust stand and operate in the relevant vacuum environment where the thruster is operating, significantly increasing the present technology readiness level of liquid metal propellant feed systems. The design of various critical components in a bismuth PMS are described. These include the bismuth reservoir and pressurization system, 'hotspot' flow sensor, power system and integrated control system. Particular emphasis is given to selection of the electronics employed in this system and the methods that were used to isolate the power and control systems from the high-temperature portions of the feed system and thruster. Open loop calibration test results from the 'hotspot' flow sensor are reported, and results of integrated thruster/PMS tests demonstrate operation of the feed system in the relevant environment.

Influence of feed provisioning prior to digesta sampling on precaecal amino acid digestibility in broiler chickens.

PubMed

Siegert, Wolfgang; Ganzer, Christian; Kluth, Holger; Rodehutscord, Markus

2018-06-01

A regression approach was applied to determine the influence of feed provisioning prior to digesta sampling on precaecal (pc) amino acid (AA) digestibility in broiler chickens. Soybean meal was used as an example test ingredient. Five feed-provisioning protocols were investigated, four with restricted provision and one with ad libitum provision. When provision was restricted, feed was provided for 30 min after a withdrawal period of 12 h. Digesta were sampled 1, 2, 4 and 6 h after feeding commenced. A diet containing 300 g maize starch/kg was prepared. Half or all the maize starch was replaced with soybean meal in two other diets. Average pc digestibility of all determined AA in the soybean meal was 86% for the 4 and 6-h protocols and 66% and 60% for the 2 and 1-h protocols, respectively. Average pc AA digestibility of soybean meal was 76% for ad libitum feed provision. Feed provisioning also influenced the determined variance. Variance in digestibility ranked in magnitude 1 h > ad libitum > 2 h > 6 h > 4 h for all AA. Owing to the considerable influence of feed-provisioning protocols found in this study, comparisons of pc AA digestibility between studies applying different protocols prior to digesta sampling must be treated with caution. Digestibility experiments aimed at providing estimates for practical feed formulation should use feed-provisioning procedures similar to those used in practice.

Growth hormone response to feeding in term and preterm neonates.

PubMed

Adrian, T E; Lucas, A; Bloom, S R; Aynsley-Green, A

1983-03-01

Plasma growth hormone concentrations were measured in 248 healthy term and preterm infants. At birth growth hormone concentrations in cord blood from both term and preterm babies were approximately 100-fold higher than those in blood drawn from healthy adults. By the sixth postnatal day basal pre-feed levels had fallen in term neonates by 65% and a marked postprandial rise was apparent; preterm infants did not show this initial fall in preprandial hormone levels nor was any response to feeding seen. However a fall in preprandial concentrations accompanied by the development of postprandial surges in growth hormone occurred during the next 2 weeks so that by 24 days the postprandial rise was similar to that of term neonates on the sixth day. We conclude that although the initial postnatal changes in plasma growth hormone concentrations are different in preterm and term infants, feeding is a major stimulus to growth hormone secretion in both groups of neonates. Further work is needed to define the precise role of this hormone in neonatal metabolic adaptation.

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2011 CFR

2011-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2013 CFR

2013-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2014 CFR

2014-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2012 CFR

2012-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2010 CFR

2010-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

Genetic and phenotypic parameter estimates for feed intake and other traits in growing beef cattle

USDA-ARS?s Scientific Manuscript database

Genetic parameters for dry matter intake (DMI), residual feed intake (RFI), average daily gain (ADG), mid-period body weight (MBW), gain to feed ratio (G:F) and flight speed (FS) were estimated using 1165 steers from a mixed-breed population using restricted maximum likelihood methodology applied to...

Tune variations in the Large Hadron Collider

NASA Astrophysics Data System (ADS)

Aquilina, N.; Giovannozzi, M.; Lamont, M.; Sammut, N.; Steinhagen, R.; Todesco, E.; Wenninger, J.

2015-04-01

The horizontal and vertical betatron tunes of the Large Hadron Collider (LHC) mainly depend on the strength of the quadrupole magnets, but are also affected by the quadrupole component in the main dipoles. In case of systematic misalignments, the sextupole component from the main dipoles and sextupole corrector magnets also affect the tunes due to the feed down effect. During the first years of operation of the LHC, the tunes have been routinely measured and corrected through either a feedback or a feed forward system. In this paper, the evolution of the tunes during injection, ramp and flat top are reconstructed from the beam measurements and the settings of the tune feedback loop and of the feed forward corrections. This gives the obtained precision of the magnetic model of the machine with respect to quadrupole and sextupole components. Measurements at the injection plateau show an unexpected large decay whose origin is not understood. This data is discussed together with the time constants and the dependence on previous cycles. We present results of dedicated experiments that show that this effect does not originate from the decay of the main dipole component. During the ramp, the tunes drift by about 0.022. It is shown that this is related to the precision of tracking the quadrupole field in the machine and this effect is reduced to about 0.01 tune units during flat top.

Telerobotic-assisted bone-drilling system using bilateral control with feed operation scaling and cutting force scaling

PubMed Central

Kasahara, Yusuke; Kawana, Hiromasa; Usuda, Shin; Ohnishi, Kouhei

2012-01-01

Background Drilling is used in the medical field, especially in oral surgery and orthopaedics. In recent years, oral surgery involving dental implants has become more common. However, the risky drilling process causes serious accidents. To prevent these accidents, supporting systems such as robotic drilling systems are required. Methods A telerobotic-assisted drilling system is proposed. An acceleration-based four-channel bilateral control system is implemented in linear actuators in a master–slave system for drill feeding. A reaction force observer is used instead of a force sensor for measuring cutting force. Cutting force transmits from a cutting material to a surgeon, who may feel a static cutting resistance force and vigorous cutting vibrations, via the master–slave system. Moreover, position scaling and force scaling are achieved. Scaling functions are used to achieve precise drilling and hazard detection via force sensation. Results Cutting accuracy and reproducibility of the cutting force were evaluated by angular velocity/position error and frequency analysis of the cutting force, respectively, and errors were > 2.0 rpm and > 0.2 mm, respectively. Spectrum peaks of the cutting vibration were at the theoretical vibration frequencies of 30, 60 and 90 Hz. Conclusions The proposed telerobotic-assisted drilling system achieved precise manipulation of the drill feed and vivid feedback from the cutting force. Copyright © 2012 John Wiley & Sons, Ltd. PMID:22271710

40 CFR 63.7325 - What test methods and other procedures must I use to demonstrate initial compliance with the TDS...

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... applied to the coke (e.g., from the header that feeds water to the quench tower reservoirs). Conduct... sample of the quench water as applied to the coke (e.g., from the header that feeds water to the quench...

40 CFR 63.7325 - What test methods and other procedures must I use to demonstrate initial compliance with the TDS...

Code of Federal Regulations, 2012 CFR

2012-07-01

...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... applied to the coke (e.g., from the header that feeds water to the quench tower reservoirs). Conduct... sample of the quench water as applied to the coke (e.g., from the header that feeds water to the quench...

40 CFR 63.7325 - What test methods and other procedures must I use to demonstrate initial compliance with the TDS...

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... applied to the coke (e.g., from the header that feeds water to the quench tower reservoirs). Conduct... sample of the quench water as applied to the coke (e.g., from the header that feeds water to the quench...

40 CFR 63.7325 - What test methods and other procedures must I use to demonstrate initial compliance with the TDS...

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... applied to the coke (e.g., from the header that feeds water to the quench tower reservoirs). Conduct... sample of the quench water as applied to the coke (e.g., from the header that feeds water to the quench...

Low-Contamination Vibrating Feeder for Silicon Chips

NASA Technical Reports Server (NTRS)

Mackintosh, B. H.

1984-01-01

Vibratory feeding is method of controlling flow of small oddly shaped particles. Technique applied to other materials that require contamination control by feeding material through vibrating troughs topped by particular material.

KSC-08pd0066

NASA Image and Video Library

2008-01-17

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, foam is being replaced around the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The foam was removed to enable engineers to remove and replace a feed-through ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0039

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- Mike Berger, with Lockheed Martin, examines the internal connector on space shuttle Atlantis' external tank to which the replacement feed-through connector in the engine cutoff, or ECO, sensor system will be attached. The replacement connector is seen below Berger's hand. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

KSC-08pd0067

NASA Image and Video Library

2008-01-17

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, foam is being replaced around the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The foam was removed to enable engineers to remove and replace a feed-through ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0036

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- This closeup shows the final splicing completed on the wiring between space shuttle Atlantis' external tank and the engine cutoff, or ECO, sensor system before the replacement feed-through connector in the ECO sensor system is installed. Cryogenic shielding is installed around the wiring. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

SYSTEMIC ACTIVITY OF NEONICOTINOIDS INFLUENCES FEEDING BY ADULT BLACK VINE WEEVILS ON VARIOUS SPECIES OF ORNAMENTALS

USDA-ARS?s Scientific Manuscript database

The black vine weevil (BVW) is a serious pest of ornamental nursery crops. The larval stage feeds on the roots of ornamental plants and small fruits often stunting or killing the plants. The adults feed on the foliage of ornamental plants. A standard management technique is to apply foliar treatm...

A New Blind Pointing Model Improves Large Reflector Antennas Precision Pointing at Ka-Band (32 GHz)

NASA Technical Reports Server (NTRS)

Rochblatt, David J.

2009-01-01

The National Aeronautics and Space Administration (NASA), Jet Propulsion Laboratory (JPL)-Deep Space Network (DSN) subnet of 34-m Beam Waveguide (BWG) Antennas was recently upgraded with Ka-Band (32-GHz) frequency feeds for space research and communication. For normal telemetry tracking a Ka-Band monopulse system is used, which typically yields 1.6-mdeg mean radial error (MRE) pointing accuracy on the 34-m diameter antennas. However, for the monopulse to be able to acquire and lock, for special radio science applications where monopulse cannot be used, or as a back-up for the monopulse, high-precision open-loop blind pointing is required. This paper describes a new 4th order pointing model and calibration technique, which was developed and applied to the DSN 34-m BWG antennas yielding 1.8 to 3.0-mdeg MRE pointing accuracy and amplitude stability of 0.2 dB, at Ka-Band, and successfully used for the CASSINI spacecraft occultation experiment at Saturn and Titan. In addition, the new 4th order pointing model was used during a telemetry experiment at Ka-Band (32 GHz) utilizing the Mars Reconnaissance Orbiter (MRO) spacecraft while at a distance of 0.225 astronomical units (AU) from Earth and communicating with a DSN 34-m BWG antenna at a record high rate of 6-megabits per second (Mb/s).

Parenting Styles, Feeding Styles, Feeding Practices, and Weight Status in 4–12 Year-Old Children: A Systematic Review of the Literature

PubMed Central

Shloim, Netalie; Edelson, Lisa R.; Martin, Nathalie; Hetherington, Marion M.

2015-01-01

Childhood is a critical period in the development of obesity. Eating patterns established early in life track into later life. Therefore, parental approaches to feeding in their general parenting style, feeding styles, and specific feeding practices will have a profound impact on how children eat and grow. A systematic research review following PRISMA guidelines was conducted to identify, discuss and integrate recent research investigating the relationship between parenting styles, feeding styles, feeding practices, and body mass index (BMI) in children. Medline (Ovid), PsycINFO, Web of Science, and Food Science and Technology Abstracts were systematically searched using sensitive search strategies. Studies were limited to papers published in English between 2010 and February 2015 with participants aged 4–12 years old with outcomes including obesity, change in weight, or BMI. The search yielded 31 relevant quantitative peer-reviewed papers meeting all inclusion criteria: seven longitudinal, 23 cross-sectional, one randomized control trial. Associations between parenting style and child BMI were strongest and most consistent within the longitudinal studies. Uninvolved, indulgent or highly protective parenting was associated with higher child BMI, whereas authoritative parenting was associated with a healthy BMI. Similarly for feeding styles, indulgent feeding was consistently associated with risk of obesity within cross-sectional studies. Specific feeding practices such as restriction and pressure to eat were linked to BMI, especially within cross-sectional studies. Where child traits were measured, the feeding practice appeared to be responsive to the child, therefore restriction was applied to children with a high BMI and pressure to eat applied to children with a lower BMI. Behaviors and styles that are specific to the feeding context are consistently associated with child BMI. However, since obesity emerges over time, it is through longitudinal, carefully measured (through questionnaire and observation) studies which take account of child appetite and temperament that the association between parenting style, feeding style, specific feeding practices, and child obesity will be understood. PMID:26696920

Parenting Styles, Feeding Styles, Feeding Practices, and Weight Status in 4-12 Year-Old Children: A Systematic Review of the Literature.

PubMed

Shloim, Netalie; Edelson, Lisa R; Martin, Nathalie; Hetherington, Marion M

2015-01-01

Childhood is a critical period in the development of obesity. Eating patterns established early in life track into later life. Therefore, parental approaches to feeding in their general parenting style, feeding styles, and specific feeding practices will have a profound impact on how children eat and grow. A systematic research review following PRISMA guidelines was conducted to identify, discuss and integrate recent research investigating the relationship between parenting styles, feeding styles, feeding practices, and body mass index (BMI) in children. Medline (Ovid), PsycINFO, Web of Science, and Food Science and Technology Abstracts were systematically searched using sensitive search strategies. Studies were limited to papers published in English between 2010 and February 2015 with participants aged 4-12 years old with outcomes including obesity, change in weight, or BMI. The search yielded 31 relevant quantitative peer-reviewed papers meeting all inclusion criteria: seven longitudinal, 23 cross-sectional, one randomized control trial. Associations between parenting style and child BMI were strongest and most consistent within the longitudinal studies. Uninvolved, indulgent or highly protective parenting was associated with higher child BMI, whereas authoritative parenting was associated with a healthy BMI. Similarly for feeding styles, indulgent feeding was consistently associated with risk of obesity within cross-sectional studies. Specific feeding practices such as restriction and pressure to eat were linked to BMI, especially within cross-sectional studies. Where child traits were measured, the feeding practice appeared to be responsive to the child, therefore restriction was applied to children with a high BMI and pressure to eat applied to children with a lower BMI. Behaviors and styles that are specific to the feeding context are consistently associated with child BMI. However, since obesity emerges over time, it is through longitudinal, carefully measured (through questionnaire and observation) studies which take account of child appetite and temperament that the association between parenting style, feeding style, specific feeding practices, and child obesity will be understood.

BAD Modulates Counterregulatory Responses to Hypoglycemia and Protective Glucoprivic Feeding

PubMed Central

Osundiji, Mayowa A.; Godes, Marina L.; Evans, Mark L.; Danial, Nika N.

2011-01-01

Hypoglycemia or glucoprivation triggers protective hormonal counterregulatory and feeding responses to aid the restoration of normoglycemia. Increasing evidence suggests pertinent roles for the brain in sensing glucoprivation and mediating counterregulation, however, the precise nature of the metabolic signals and molecular mediators linking central glucose sensing to effector functions are not fully understood. Here, we demonstrate that protective hormonal and feeding responses to hypoglycemia are regulated by BAD, a BCL-2 family protein with dual functions in apoptosis and metabolism. BAD-deficient mice display impaired glycemic and hormonal counterregulatory responses to systemic glucoprivation induced by 2-deoxy-D-glucose. BAD is also required for proper counterregulatory responses to insulin-induced hypoglycemia as evident from significantly higher glucose infusion rates and lower plasma epinephrine levels during hyperinsulinemic hypoglycemic clamps. Importantly, RNA interference-mediated acute knockdown of Bad in the brain provided independent genetic evidence for its relevance in central glucose sensing and proper neurohumoral responses to glucoprivation. Moreover, BAD deficiency is associated with impaired glucoprivic feeding, suggesting that its role in adaptive responses to hypoglycemia extends beyond hormonal responses to regulation of feeding behavior. Together, these data indicate a previously unappreciated role for BAD in the control of central glucose sensing. PMID:22162752

Interval timing in genetically modified mice: a simple paradigm

PubMed Central

Balci, F.; Papachristos, E. B.; Gallistel, C. R.; Brunner, D.; Gibson, J.; Shumyatsky, G. P.

2009-01-01

We describe a behavioral screen for the quantitative study of interval timing and interval memory in mice. Mice learn to switch from a short-latency feeding station to a long-latency station when the short latency has passed without a feeding. The psychometric function is the cumulative distribution of switch latencies. Its median measures timing accuracy and its interquartile interval measures timing precision. Next, using this behavioral paradigm, we have examined mice with a gene knockout of the receptor for gastrin-releasing peptide that show enhanced (i.e. prolonged) freezing in fear conditioning. We have tested the hypothesis that the mutants freeze longer because they are more uncertain than wild types about when to expect the electric shock. The knockouts however show normal accuracy and precision in timing, so we have rejected this alternative hypothesis. Last, we conduct the pharmacological validation of our behavioral screen using D-amphetamine and methamphetamine. We suggest including the analysis of interval timing and temporal memory in tests of genetically modified mice for learning and memory and argue that our paradigm allows this to be done simply and efficiently. PMID:17696995

Interval timing in genetically modified mice: a simple paradigm.

PubMed

Balci, F; Papachristos, E B; Gallistel, C R; Brunner, D; Gibson, J; Shumyatsky, G P

2008-04-01

We describe a behavioral screen for the quantitative study of interval timing and interval memory in mice. Mice learn to switch from a short-latency feeding station to a long-latency station when the short latency has passed without a feeding. The psychometric function is the cumulative distribution of switch latencies. Its median measures timing accuracy and its interquartile interval measures timing precision. Next, using this behavioral paradigm, we have examined mice with a gene knockout of the receptor for gastrin-releasing peptide that show enhanced (i.e. prolonged) freezing in fear conditioning. We have tested the hypothesis that the mutants freeze longer because they are more uncertain than wild types about when to expect the electric shock. The knockouts however show normal accuracy and precision in timing, so we have rejected this alternative hypothesis. Last, we conduct the pharmacological validation of our behavioral screen using d-amphetamine and methamphetamine. We suggest including the analysis of interval timing and temporal memory in tests of genetically modified mice for learning and memory and argue that our paradigm allows this to be done simply and efficiently.

Polymeric check valve with an elevated pedestal for precise cracking pressure in a glaucoma drainage device.

PubMed

Park, Chang-Ju; Yang, Dong-Seong; Cha, Jung-Joon; Lee, Jong-Hyun

2016-02-01

This paper presents the design, fabrication, and characterization of a polymeric micro check valve for a glaucoma drainage device (GDD) featuring the precise regulation of intraocular pressure (IOP) and effective aqueous humor turnover (AHT). The pedestal, slightly elevated by selective coating of a parylene C film, induces pre-stress in the thin valve membrane, which enhances the predictability of the cracking pressure of the GDD. The proposed GDD comprises a cannula and a normally closed polymeric micro check valve, which are made of PDMS, a biocompatible polymer, with three layers: top (cover), intermediate (thin valve membrane), and bottom (base plate). A feedback channel, located between the top and intermediate layers, prevents reverse flow by feeding the pressure of the outlet channel back to the thin valve membrane. To achieve a precise cracking pressure and sufficient drainage of humor for humans, the thicknesses of the valve membrane and parylene C film are designed to be 58 μm and 1 μm, respectively, which are confirmed using a COMSOL simulation. The experimental results show that the cracking pressure of the fabricated GDD lies within the range of normal IOP (1.33-2.67 kPa). The forward flow rate (drainage rate), 4.3 ± 0.9 μL/min at 2.5 kPa, is adequate to accommodate the rate of AHT in a normal human eye (2.4 ± 0.6 μL/min). The reverse flow was not observed when a hydrostatic pressure of up to 4 kPa was applied to the outlet and the feedback channel.

Basic Research in Plasma Medicine - A Throughput Approach from Liquids to Cells

PubMed Central

Bekeschus, Sander; Schmidt, Anke; Niessner, Felix; Gerling, Torsten; Weltmann, Klaus-Dieter; Wende, Kristian

2017-01-01

In plasma medicine, ionized gases with temperatures close to that of vertebrate systems are applied to cells and tissues. Cold plasmas generate reactive species known to redox regulate biological processes in health and disease. Pre-clinical and clinical evidence points to beneficial effects of plasma treatment in the healing of chronic ulcer of the skin. Other emerging topics, such as plasma cancer treatment, are receiving increasing attention. Plasma medical research requires interdisciplinary expertise in physics, chemistry, and biomedicine. One goal of plasma research is to characterize plasma-treated cells in a variety of specific applications. This includes, for example, cell count and viability, cellular oxidation, mitochondrial activity, cytotoxicity and mode of cell death, cell cycle analysis, cell surface marker expression, and cytokine release. This study describes the essential equipment and workflows required for such research in plasma biomedicine. It describes the proper operation of an atmospheric pressure argon plasma jet, specifically monitoring its basic emission spectra and feed gas settings to modulate reactive species output. Using a high-precision xyz-table and computer software, the jet is hovered in millisecond-precision over the cavities of 96-well plates in micrometer-precision for maximal reproducibility. Downstream assays for liquid analysis of redox-active molecules are shown, and target cells are plasma-treated. Specifically, melanoma cells are analyzed in an efficient sequence of different consecutive assays but using the same cells: measurement of metabolic activity, total cell area, and surface marker expression of calreticulin, a molecule important for the immunogenic cell death of cancer cells. These assays retrieve content-rich biological information about plasma effects from a single plate. Altogether, this study describes the essential steps and protocols for plasma medical research. PMID:29286412

Basic Research in Plasma Medicine - A Throughput Approach from Liquids to Cells.

PubMed

Bekeschus, Sander; Schmidt, Anke; Niessner, Felix; Gerling, Torsten; Weltmann, Klaus-Dieter; Wende, Kristian

2017-11-17

In plasma medicine, ionized gases with temperatures close to that of vertebrate systems are applied to cells and tissues. Cold plasmas generate reactive species known to redox regulate biological processes in health and disease. Pre-clinical and clinical evidence points to beneficial effects of plasma treatment in the healing of chronic ulcer of the skin. Other emerging topics, such as plasma cancer treatment, are receiving increasing attention. Plasma medical research requires interdisciplinary expertise in physics, chemistry, and biomedicine. One goal of plasma research is to characterize plasma-treated cells in a variety of specific applications. This includes, for example, cell count and viability, cellular oxidation, mitochondrial activity, cytotoxicity and mode of cell death, cell cycle analysis, cell surface marker expression, and cytokine release. This study describes the essential equipment and workflows required for such research in plasma biomedicine. It describes the proper operation of an atmospheric pressure argon plasma jet, specifically monitoring its basic emission spectra and feed gas settings to modulate reactive species output. Using a high-precision xyz-table and computer software, the jet is hovered in millisecond-precision over the cavities of 96-well plates in micrometer-precision for maximal reproducibility. Downstream assays for liquid analysis of redox-active molecules are shown, and target cells are plasma-treated. Specifically, melanoma cells are analyzed in an efficient sequence of different consecutive assays but using the same cells: measurement of metabolic activity, total cell area, and surface marker expression of calreticulin, a molecule important for the immunogenic cell death of cancer cells. These assays retrieve content-rich biological information about plasma effects from a single plate. Altogether, this study describes the essential steps and protocols for plasma medical research.

40 CFR 503.11 - Special definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... applied to an area of land. (g) Forest is a tract of land thick with trees and underbrush. (h) Land... feed directly on feed crops such as legumes, grasses, grain stubble, or stover. (l) Public contact site...

40 CFR 503.11 - Special definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... applied to an area of land. (g) Forest is a tract of land thick with trees and underbrush. (h) Land... feed directly on feed crops such as legumes, grasses, grain stubble, or stover. (l) Public contact site...

Cell-controlled hybrid perfusion fed-batch CHO cell process provides significant productivity improvement over conventional fed-batch cultures.

PubMed

Hiller, Gregory W; Ovalle, Ana Maria; Gagnon, Matthew P; Curran, Meredith L; Wang, Wenge

2017-07-01

A simple method originally designed to control lactate accumulation in fed-batch cultures of Chinese Hamster Ovary (CHO) cells has been modified and extended to allow cells in culture to control their own rate of perfusion to precisely deliver nutritional requirements. The method allows for very fast expansion of cells to high density while using a minimal volume of concentrated perfusion medium. When the short-duration cell-controlled perfusion is performed in the production bioreactor and is immediately followed by a conventional fed-batch culture using highly concentrated feeds, the overall productivity of the culture is approximately doubled when compared with a highly optimized state-of-the-art fed-batch process. The technology was applied with near uniform success to five CHO cell processes producing five different humanized monoclonal antibodies. The increases in productivity were due to the increases in sustained viable cell densities. Biotechnol. Bioeng. 2017;114: 1438-1447. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Mechanism and experimental research on ultra-precision grinding of ferrite

NASA Astrophysics Data System (ADS)

Ban, Xinxing; Zhao, Huiying; Dong, Longchao; Zhu, Xueliang; Zhang, Chupeng; Gu, Yawen

2017-02-01

Ultra-precision grinding of ferrite is conducted to investigate the removal mechanism. Effect of the accuracy of machine tool key components on grinding surface quality is analyzed. The surface generation model of ferrite ultra-precision grinding machining is established. In order to reveal the surface formation mechanism of ferrite in the process of ultraprecision grinding, furthermore, the scientific and accurate of the calculation model are taken into account to verify the grinding surface roughness, which is proposed. Orthogonal experiment is designed using the high precision aerostatic turntable and aerostatic spindle for ferrite which is a typical hard brittle materials. Based on the experimental results, the influence factors and laws of ultra-precision grinding surface of ferrite are discussed through the analysis of the surface roughness. The results show that the quality of ferrite grinding surface is the optimal parameters, when the wheel speed of 20000r/mm, feed rate of 10mm/min, grinding depth of 0.005mm, and turntable rotary speed of 5r/min, the surface roughness Ra can up to 75nm.

An overview of tests for animal tissues in feeds applied in response to public health concerns regarding bovine spongiform encephalopathy.

PubMed

Gizzi, G; van Raamsdonk, L W D; Baeten, V; Murray, I; Berben, G; Brambilla, G; von Holst, C

2003-04-01

Enforcing the ban on meat-and-bone meal in feed for farmed animals, and especially ruminants, is considered an important measure to prevent the spread of bovine spongiform encephalopathy. The authors describe current analytical methods for the detection and identification of animal tissues in feed. In addition, recently approved requirements, such as the ban of intra-species recycling (practice of feeding an animal species with proteins derived from the bodies, or parts of bodies, of the same species) are described. In principle, four different approaches are currently applied, i.e. microscopic analysis, polymerase chain reaction, immunoassay analysis and near infrared spectroscopy or microscopy. The principal performance characteristics of these methods are presented and compared, and their specific advantages and disadvantages described. Special emphasis is also placed on the impact of rendering conditions, particularly high temperatures and on the use of molecular biology techniques.

Robust iterative learning contouring controller with disturbance observer for machine tool feed drives.

PubMed

Simba, Kenneth Renny; Bui, Ba Dinh; Msukwa, Mathew Renny; Uchiyama, Naoki

2018-04-01

In feed drive systems, particularly machine tools, a contour error is more significant than the individual axial tracking errors from the view point of enhancing precision in manufacturing and production systems. The contour error must be within the permissible tolerance of given products. In machining complex or sharp-corner products, large contour errors occur mainly owing to discontinuous trajectories and the existence of nonlinear uncertainties. Therefore, it is indispensable to design robust controllers that can enhance the tracking ability of feed drive systems. In this study, an iterative learning contouring controller consisting of a classical Proportional-Derivative (PD) controller and disturbance observer is proposed. The proposed controller was evaluated experimentally by using a typical sharp-corner trajectory, and its performance was compared with that of conventional controllers. The results revealed that the maximum contour error can be reduced by about 37% on average. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

KSC-08pd0062

NASA Image and Video Library

2008-01-16

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, foam insulation is being trimmed for placement around the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The foam was removed to enable engineers to remove and replace a feed-through ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0064

NASA Image and Video Library

2008-01-16

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, foam insulation is being trimmed for placement around the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The foam was removed to enable engineers to remove and replace a feed-through ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0063

NASA Image and Video Library

2008-01-16

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, foam insulation is being trimmed for placement around the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The foam was removed to enable engineers to remove and replace a feed-through ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0068

NASA Image and Video Library

2008-01-17

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, a technician trims foam placed around the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The foam was removed to enable engineers to remove and replace a feed-through ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0065

NASA Image and Video Library

2008-01-16

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, foam insulation is being trimmed for placement around the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The foam was removed to enable engineers to remove and replace a feed-through ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

A Kinect-based system for automatic recording of some pigeon behaviors.

PubMed

Lyons, Damian M; MacDonall, James S; Cunningham, Kelly M

2015-12-01

Contact switches and touch screens are the state of the art for recording pigeons' pecking behavior. Recording other behavior, however, requires a different sensor for each behavior, and some behaviors cannot easily be recorded. We present a flexible and inexpensive image-based approach to detecting and counting pigeon behaviors that is based on the Kinect sensor from Microsoft. Although the system is as easy to set up and use as the standard approaches, it is more flexible because it can record behaviors in addition to key pecking. In this article, we show how both the fast, fine motion of key pecking and the gross body activity of feeding can be measured. Five pigeons were trained to peck at a lighted contact switch, a pigeon key, to obtain food reward. The timing of the pecks and the food reward signals were recorded in a log file using standard equipment. The Kinect-based system, called BehaviorWatch, also measured the pecking and feeding behavior and generated a different log file. For key pecking, BehaviorWatch had an average sensitivity of 95% and a precision of 91%, which were very similar to the pecking measurements from the standard equipment. For detecting feeding activity, BehaviorWatch had a sensitivity of 95% and a precision of 97%. These results allow us to demonstrate that an advantage of the Kinect-based approach is that it can also be reliably used to measure activity other than key pecking.

Modeling, simulation and control of pulsed DE-GMA welding process for joining of aluminum to steel

NASA Astrophysics Data System (ADS)

Zhang, Gang; Shi, Yu; Li, Jie; Huang, Jiankang; Fan, Ding

2014-09-01

Joining of aluminum to steel has attracted significant attention from the welding research community, automotive and rail transportation industries. Many current welding methods have been developed and applied, however, they can not precisely control the heat input to work-piece, they are high costs, low efficiency and consist lots of complex welding devices, and the generated intermetallic compound layer in weld bead interface is thicker. A novel pulsed double electrode gas metal arc welding(Pulsed DE-GMAW) method is developed. To achieve a stable welding process for joining of aluminum to steel, a mathematical model of coupled arc is established, and a new control scheme that uses the average feedback arc voltage of main loop to adjust the wire feed speed to control coupled arc length is proposed and developed. Then, the impulse control simulation of coupled arc length, wire feed speed and wire extension is conducted to demonstrate the mathematical model and predict the stability of welding process by changing the distance of contact tip to work-piece(CTWD). To prove the proposed PSO based PID control scheme's feasibility, the rapid prototyping experimental system is setup and the bead-on-plate control experiments are conducted to join aluminum to steel. The impulse control simulation shows that the established model can accurately represent the variation of coupled arc length, wire feed speed and the average main arc voltage when the welding process is disturbed, and the developed controller has a faster response and adjustment, only runs about 0.1 s. The captured electric signals show the main arc voltage gradually closes to the supposed arc voltage by adjusting the wire feed speed in 0.8 s. The obtained typical current waveform demonstrates that the main current can be reduced by controlling the bypass current under maintaining a relative large total current. The control experiment proves the accuracy of proposed model and feasibility of new control scheme further. The beautiful and smooth weld beads are also obtained by this method. Pulsed DE-GMAW can thus be considered as an alternative method for low cost, high efficiency joining of aluminum to steel.

GSM Web-Based Centralized Remote Wireless Automatic Controlling and Monitoring of Aquafeeder

NASA Astrophysics Data System (ADS)

Wong, C. L.; Idris, A.; Hasan, Z.

2016-03-01

This project is about producing a prototype to feed fishes at fish ponds of remote location with the use of GSM mobile phone. An automatic fish feeder is an electric device that has been designed to give out the right amount of pellets at the designed time. In this project, the automatic feeder designed consists of photovoltaic solar cells that are used to generate electricity and storing it into batteries. Solar charge controllers can be used to determine the rate of which current is drawn and added from the batteries. GSM cellular communication is used to allow user to control from a distance. Commands or instructions are sent to the operating system which in return runs the servomotor and blower by blowing certain amount of fish pallets into the pond to feed the fishes. The duration of the feeding processes is fixed by the user, hence the amount of fish food pallets released are precisely the same for each time. This technology is especially useful for fish farmers where they can remotely feed their fishes.

Authentication of meat and meat products vs. detection of animal species in feed - what is the difference?

NASA Astrophysics Data System (ADS)

Nešić, K.; Stojanović, D.; Baltić, Ž. M.

2017-09-01

Authenticity of food is an issue that is growing in awareness and concern. Although food adulteration has been present since antiquity, it has broadened to include entire global populations as modern food supply chains have expanded, enriched and become more complex. Different forms of adulteration influence not only the quality of food products, but also may cause harmful health effects. Meat and meat products are often subjected to counterfeiting, mislabelling and similar fraudulent activities, while substitutions of meat ingredients with other animal species is one among many forms of food fraud. Feed is also subject to testing for the presence of different animal species, but as part of the eradication process of transmissible spongiform encephalopathies (TSE). In both food and feed cases, the final goal is consumer protection, which should be provided by quick, precise and specific tools. Several analytical tests have been employed for such needs. This paper provides an overview of authentication of meat and meat products compared with species identification in feed control, highlighting the most prevalent laboratory methods.

The Screening Tool of Feeding Problems Applied to Children (STEP-CHILD): Psychometric Characteristics and Associations with Child and Parent Variables

ERIC Educational Resources Information Center

Seiverling, Laura; Hendy, Helen M.; Williams, Keith

2011-01-01

The present study evaluated the 23-item Screening Tool for Feeding Problems (STEP; Matson & Kuhn, 2001) with a sample of children referred to a hospital-based feeding clinic to examine the scale's psychometric characteristics and then demonstrate how a children's revision of the STEP, the STEP-CHILD is associated with child and parent variables.…

Unexpected arousal modulates the influence of sensory noise on confidence

PubMed Central

Allen, Micah; Frank, Darya; Schwarzkopf, D Samuel; Fardo, Francesca; Winston, Joel S; Hauser, Tobias U; Rees, Geraint

2016-01-01

Human perception is invariably accompanied by a graded feeling of confidence that guides metacognitive awareness and decision-making. It is often assumed that this arises solely from the feed-forward encoding of the strength or precision of sensory inputs. In contrast, interoceptive inference models suggest that confidence reflects a weighted integration of sensory precision and expectations about internal states, such as arousal. Here we test this hypothesis using a novel psychophysical paradigm, in which unseen disgust-cues induced unexpected, unconscious arousal just before participants discriminated motion signals of variable precision. Across measures of perceptual bias, uncertainty, and physiological arousal we found that arousing disgust cues modulated the encoding of sensory noise. Furthermore, the degree to which trial-by-trial pupil fluctuations encoded this nonlinear interaction correlated with trial level confidence. Our results suggest that unexpected arousal regulates perceptual precision, such that subjective confidence reflects the integration of both external sensory and internal, embodied states. DOI: http://dx.doi.org/10.7554/eLife.18103.001 PMID:27776633

The impact of water exchange rate on the health and performance of rainbow trout Oncorhynchus mykiss in recirculation aquaculture systems

USDA-ARS?s Scientific Manuscript database

Fish mortality in recirculating aquaculture systems (RAS) has been observed by the authors to increase when RAS are managed at low makeup water exchange rates with relatively high feed loading. The precise etiology of this elevated mortality was unknown, all typical water quality parameters were wit...

The study of optimization on process parameters of high-accuracy computerized numerical control polishing

NASA Astrophysics Data System (ADS)

Huang, Wei-Ren; Huang, Shih-Pu; Tsai, Tsung-Yueh; Lin, Yi-Jyun; Yu, Zong-Ru; Kuo, Ching-Hsiang; Hsu, Wei-Yao; Young, Hong-Tsu

2017-09-01

Spherical lenses lead to forming spherical aberration and reduced optical performance. Consequently, in practice optical system shall apply a combination of spherical lenses for aberration correction. Thus, the volume of the optical system increased. In modern optical systems, aspherical lenses have been widely used because of their high optical performance with less optical components. However, aspherical surfaces cannot be fabricated by traditional full aperture polishing process due to their varying curvature. Sub-aperture computer numerical control (CNC) polishing is adopted for aspherical surface fabrication in recent years. By using CNC polishing process, mid-spatial frequency (MSF) error is normally accompanied during this process. And the MSF surface texture of optics decreases the optical performance for high precision optical system, especially for short-wavelength applications. Based on a bonnet polishing CNC machine, this study focuses on the relationship between MSF surface texture and CNC polishing parameters, which include feed rate, head speed, track spacing and path direction. The power spectral density (PSD) analysis is used to judge the MSF level caused by those polishing parameters. The test results show that controlling the removal depth of single polishing path, through the feed rate, and without same direction polishing path for higher total removal depth can efficiently reduce the MSF error. To verify the optical polishing parameters, we divided a correction polishing process to several polishing runs with different direction polishing paths. Compare to one shot polishing run, multi-direction path polishing plan could produce better surface quality on the optics.

Ataxia Telangiectasia in Siblings: Oral Motor and Swallowing Characterization.

PubMed

Rondon-Melo, Silmara; de Almeida, Isabel Junqueira; Andrade, Claudia Regina Furquim de; Sassi, Fernanda Chiarion; Molini-Avejonas, Daniela Regina

2017-07-12

BACKGROUND The body of literature on oral motor and swallowing disorders in patients with ataxia telangiectasia (AT) is limited. CASE REPORT The purpose of this study was to characterize oral motor and swallowing disorders in two siblings with AT, based on oral motor and swallowing assessments. Specific procedures were applied for oral motor and swallowing assessments and both patients underwent videofluoroscopy (VFS). Case 1 presented vocal instability, change in postural control during feeding; food retention in oral cavity; slower oral transit time; and multiple swallowing (signs for solid and liquid). Case 2 presented parted lips at rest and reduced muscle strength; reduced strength and mobility of the tongue; vocal weakness and instability; reduced speech precision and intelligibility; decreased intonation pattern; food retention in oral cavity during feeding; slower oral transit time; multiple swallowing (signs for solid and liquid); poor bolus ejection; incoordination and difficulty in controlling the sips of water taken from the cup; altered cervical auscultation after swallowing and respiratory distress (liquid and puree). For both patients VFS results revealed laryngeal penetration for liquid. CONCLUSIONS Although the literature describes the occurrence of dysarthria and swallowing disorders in patients with AT, little attention has been given to describing which oral motor deficits are responsible for these disorders. Early identification of swallowing alterations and rehabilitation could decrease the risk of aspiration pneumonia. Future studies are necessary in order to investigate the deterioration process of swallowing in AT and the influence of rehabilitation in maintaining functional health.

A thematic review of life cycle assessment (LCA) applied to pig production

DOE Office of Scientific and Technical Information (OSTI.GOV)

McAuliffe, Graham A., E-mail: g.a.mcauliffe@umail.ucc.ie; School of Biological, Earth and Environmental Sciences, University College Cork, Distillery Fields, North Mall, Cork; Chapman, Deborah V.

Commercial livestock production is known to have significant impacts on the environment. Pig production is a complex system which involves the production of animal feed, transportation, animal rearing and waste management. One tool for assessing the environmental performance of such complex systems is life cycle assessment (LCA). LCA has been applied to pig production considerably to date. This paper provides a chronological review of state-of-the-art pig production LCAs under three themes: feed production; entire-system livestock rearing; and waste management. The study considers how LCA applications have addressed technological improvements in animal husbandry, and highlights methodological limitations, particularly related to cross-studymore » comparisons. Recent research demonstrates crude protein reduction in feed and anaerobic treatment of pig excreta resulting in bioenergy production are the key targets for environmental performance improvements related to pig production. - Highlights: • An extensive review of LCA applied to pig production is provided chronologically over the past decade. • Individual studies have been categorised into feed, whole-system pig production and waste management themes. • We consider how LCAs have addressed state-of-the-art pig husbandry. • We offer a discussion on key findings, limitations and future research.« less

[Correlation between feeding index and growth development of 6-36 month-old infants in two counties of western China by applying multiple correspondence analysis].

PubMed

Chen, Hong-da; Hao, Bo; Kang, Xiao-ping; Zhao, Geng-li; Zhou, Min

2012-06-18

To explore the correlation between feeding index and growth development status of infants from two counties of western China by applying the method of multiple correspondence analysis. Two sample counties were randomly selected from the ones that satisfied the research conditions in Shaanxi province and Chongqing in western China. In the study, 472 premature/low birth weight infants (PLBW) and 461 normal term infants (NT) of 6-36 months from the two counties were investigated from September 2010 to November 2010. The SPSS 19.0 software was applied to analyze the data using general statistical analysis and multiple correspondence analysis. In the two counties of western China, the proportion of infants with feeding index at the medium level was the highest, which was between 50% and 60%. In the PLBW group and the NT group, the proportion of low level of feeding index among 6-9 month-old infants was the highest, and the proportion was 33.3% for the PLBW group and 29.4% for the NT group. For both the PLBW group and the NT group, the distribution of feeding index among the different age groups showed significant difference (P<0.05).Among the infants with low level of feeding index, the growth development of the PLBW lay behind that of the NT. We could see a catching-up trend of the PLBW with medium or good level of feeding index, but their growth development index was still at a lower level than that of the NT with the same level of feeding condition. Through multiple correspondence analyses, the outcomes of PLBW corresponded and strongly correlated with low level of feeding index, low level of growth development index, mother's low education degree and low annual family income. And the outcomes of NT corresponded and strongly correlated with medium/good level of feeding index, medium level of growth development status, mother's medium/high education degree and medium/high level of annual family income. There are good correspondence correlations at different hierarchical levels of the infants' group, feeding index, growth development index and family factors in the two counties of western China. Multiple correspondence analysis could directly reveal the correlation among several variables, which is a suitable method for categorical data. The result can be illustrated directly through a two-dimensional graph and could provide the suggestion of feeding practice for different infants in western rural China.

Biotechnological application of functional genomics towards plant-parasitic nematode control.

PubMed

Li, Jiarui; Todd, Timothy C; Lee, Junghoon; Trick, Harold N

2011-12-01

Plant-parasitic nematodes are primary biotic factors limiting the crop production. Current nematode control strategies include nematicides, crop rotation and resistant cultivars, but each has serious limitations. RNA interference (RNAi) represents a major breakthrough in the application of functional genomics for plant-parasitic nematode control. RNAi-induced suppression of numerous genes essential for nematode development, reproduction or parasitism has been demonstrated, highlighting the considerable potential for using this strategy to control damaging pest populations. In an effort to find more suitable and effective gene targets for silencing, researchers are employing functional genomics methodologies, including genome sequencing and transcriptome profiling. Microarrays have been used for studying the interactions between nematodes and plant roots and to measure both plants and nematodes transcripts. Furthermore, laser capture microdissection has been applied for the precise dissection of nematode feeding sites (syncytia) to allow the study of gene expression specifically in syncytia. In the near future, small RNA sequencing techniques will provide more direct information for elucidating small RNA regulatory mechanisms in plants and specific gene silencing using artificial microRNAs should further improve the potential of targeted gene silencing as a strategy for nematode management. © 2011 The Authors. Plant Biotechnology Journal © 2011 Society for Experimental Biology, Association of Applied Biologists and Blackwell Publishing Ltd.

High-power Yb-fiber comb with feed-forward control of nonlinear-polarization-rotation mode-locking and large-mode-area fiber amplification.

PubMed

Yan, Ming; Li, Wenxue; Yang, Kangwen; Zhou, Hui; Shen, Xuling; Zhou, Qian; Ru, Qitian; Bai, Dongbi; Zeng, Heping

2012-05-01

We report on a simple scheme to precisely control carrier-envelope phase of a nonlinear-polarization-rotation mode-locked self-started Yb-fiber laser system with an average output power of ∼7  W and a pulse width of 130 fs. The offset frequency was locked to the repetition rate of ∼64.5  MHz with a relative linewidth of ∼1.4  MHz by using a self-referenced feed-forward scheme based on an acousto-optic frequency shifter. The phase noise and timing jitter were calculated to be 370 mrad and 120 as, respectively.

Direct deposit of catalyst on the membrane of direct feed fuel cells

NASA Technical Reports Server (NTRS)

Chun, William (Inventor); Narayanan, Sekharipuram R. (Inventor); Jeffries-Nakamura, Barbara (Inventor); Valdez, Thomas I. (Inventor); Linke, Juergen (Inventor)

2001-01-01

An improved direct liquid-feed fuel cell having a solid membrane electrolyte for electrochemical reactions of an organic fuel. Catalyst utilization and catalyst/membrane interface improvements are disclosed. Specifically, the catalyst layer is applied directly onto the membrane electrolyte.

A Framework to Evaluate Wildlife Feeding in Research, Wildlife Management, Tourism and Recreation.

PubMed

Dubois, Sara; Fraser, David

2013-10-11

Feeding of wildlife occurs in the context of research, wildlife management, tourism and in opportunistic ways. A review of examples shows that although feeding is often motivated by good intentions, it can lead to problems of public safety and conservation and be detrimental to the welfare of the animals. Examples from British Columbia illustrate the problems (nuisance animal activity, public safety risk) and consequences (culling, translocation) that often arise from uncontrolled feeding. Three features of wildlife feeding can be distinguished: the feasibility of control, the effects on conservation and the effects on animal welfare. An evaluative framework incorporating these three features was applied to examples of feeding from the literature. The cases of feeding for research and management purposes were generally found to be acceptable, while cases of feeding for tourism or opportunistic feeding were generally unacceptable. The framework should allow managers and policy-makers to distinguish acceptable from unacceptable forms of wildlife feeding as a basis for policy, public education and enforcement. Many harmful forms of wildlife feeding seem unlikely to change until they come to be seen as socially unacceptable.

Octopamine: a new feeding modulator in Lymnaea

PubMed Central

Vehovszky, Á.

1998-01-01

The role of octopamine (OA) in the feeding system of the pond snail, Lymnaea stagnalis, was studied by applying behavioural tests on intact animals, and a combination of electrophysiological analysis and morphological labelling in the isolated central nervous system. OA antagonists phentolamine, demethylchlordimeform (DCDM) and 2-chloro-4-methyl-2-(phenylimino)-imidazolidine (NC-7) were injected into intact snails and the sucrose-induced feeding response of animals was monitored. Snails that received 25 to 50 mg kg-1 phentolamine did not start feeding in sucrose, and the same dose of NC-7 reduced the number of feeding animals by 80 to 90% 1 to 3 hours after injection. DCDM treatment reduced feeding by 20 to 60%. In addition, both phentolamine and NC-7 significantly decreased the feeding rate of those animals that still accepted food after 1 to 6 hours of injection. In the central nervous system a pair of buccal neurons was identified by electrophysiological and morphological criteria. After double labelling (intracellular staining with Lucifer yellow followed by OA-immunocytochemistry) these neurons were shown to be OA immunoreactive, and electrophysiological experiments confirmed that they are members of the buccal feeding system. Therefore the newly identified buccal neurons were called OC neurons (putative octopamine containing neurons or octopaminergic cells). Synchronous intracellular recordings demonstrated that the OC neurons share a common rhythm with feeding neurons either appearing spontaneously or evoked by intracellularly stimulated feeding interneurons. OC neurons also have synaptic connections with identified members of the feeding network: electrical coupling was demonstrated between OC neurons and members of the B4 cluster motoneurons, furthermore, chemically transmitted synaptic responses were recorded both on feeding motoneurons (B1, B2 cells) and the SO modulatory interneuron after the stimulation of OC neurons. However, elementary synaptic potentials could not be recorded on the follower cells of OC neurons. Prolonged (20 to 30 s) intracellular stimulation of OC cells activated the buccal feeding neurons leading to rhythmic activity pattern (fictive feeding) in a way similar to OA applied by perfusion onto isolated central nervous system (CNS) preparations. Our results suggest that OA acts as a modulatory substance in the feeding system of Lymnaea stagnalis and the newly identified pair of OC neurons belongs to the buccal feeding network.

Improvements on GPS Location Cluster Analysis for the Prediction of Large Carnivore Feeding Activities: Ground-Truth Detection Probability and Inclusion of Activity Sensor Measures

PubMed Central

Blecha, Kevin A.; Alldredge, Mat W.

2015-01-01

Animal space use studies using GPS collar technology are increasingly incorporating behavior based analysis of spatio-temporal data in order to expand inferences of resource use. GPS location cluster analysis is one such technique applied to large carnivores to identify the timing and location of feeding events. For logistical and financial reasons, researchers often implement predictive models for identifying these events. We present two separate improvements for predictive models that future practitioners can implement. Thus far, feeding prediction models have incorporated a small range of covariates, usually limited to spatio-temporal characteristics of the GPS data. Using GPS collared cougar (Puma concolor) we include activity sensor data as an additional covariate to increase prediction performance of feeding presence/absence. Integral to the predictive modeling of feeding events is a ground-truthing component, in which GPS location clusters are visited by human observers to confirm the presence or absence of feeding remains. Failing to account for sources of ground-truthing false-absences can bias the number of predicted feeding events to be low. Thus we account for some ground-truthing error sources directly in the model with covariates and when applying model predictions. Accounting for these errors resulted in a 10% increase in the number of clusters predicted to be feeding events. Using a double-observer design, we show that the ground-truthing false-absence rate is relatively low (4%) using a search delay of 2–60 days. Overall, we provide two separate improvements to the GPS cluster analysis techniques that can be expanded upon and implemented in future studies interested in identifying feeding behaviors of large carnivores. PMID:26398546

'Intelligent' system's cost-cutting power.

PubMed

Dodge, Jeremy

2010-05-01

Jeremy Dodge, business manager at Marshall Tufflex Energy Management, explains how a voltage optimisation system that, in a claimed industry first, uses "auto-transformers" to reduce incoming mains electricity voltage so that electrical equipment receives precisely the "outgoing feed" it needs to function optimally and no more, thus significantly reducing wastage, can help major electricity users cut their bills "by as much as 25%".

Elevating Precision Agriculture to New Heights

ERIC Educational Resources Information Center

Smith, Kayla

2017-01-01

The world population is expected to reach 9.2 billion by the year 2050. Farmers are faced with the daily challenge of how to feed these people while availability of land and water is dwindling. The growth rates of global agricultural production and crop yields have slowed in the last couple of years, raising fears that the world may not be able to…

Modulation of parathion toxicity by glucose feeding: Is nitric oxide involved?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu Jing; Gupta, Ramesh C.; Goad, John T.

2007-03-15

Glucose feeding can markedly exacerbate the toxicity of the anticholinesterase insecticide, parathion. We determined the effects of parathion on brain nitric oxide and its possible role in potentiation of toxicity by glucose feeding. Adult rats were given water or 15% glucose in water for 3 days and challenged with vehicle or parathion (18 mg/kg, s.c.) on day 4. Functional signs, plasma glucose and brain cholinesterase, citrulline (an indicator of nitric oxide production) and high-energy phosphates (HEPs) were measured 1-3 days after parathion. Glucose feeding exacerbated cholinergic toxicity. Parathion increased plasma glucose (15-33%) and decreased cortical cholinesterase activity (81-90%), with nomore » significant differences between water and glucose treatment groups. In contrast, parathion increased brain regional citrulline (40-47%) and decreased HEPs (18-40%) in rats drinking water, with significantly greater changes in glucose-fed rats (248-363% increase and 31-61% decrease, respectively). We then studied the effects of inhibiting neuronal nitric oxide synthase (nNOS) by 7-nitroindazole (7NI, 30 mg/kg, i.p. x4) on parathion toxicity and its modulation by glucose feeding. Co-exposure to parathion and 7NI led to a marked increase in cholinergic signs of toxicity and lethality, regardless of glucose intake. Thus, glucose feeding enhanced the accumulation of brain nitric oxide following parathion exposure, but inhibition of nitric oxide synthesis was ineffective at counteracting increased parathion toxicity associated with glucose feeding. Evidence is therefore presented to suggest that nitric oxide may play both toxic and protective roles in cholinergic toxicity, and its precise contribution to modulation by glucose feeding requires further investigation.« less

Bullet trajectory reconstruction - Methods, accuracy and precision.

PubMed

Mattijssen, Erwin J A T; Kerkhoff, Wim

2016-05-01

Based on the spatial relation between a primary and secondary bullet defect or on the shape and dimensions of the primary bullet defect, a bullet's trajectory prior to impact can be estimated for a shooting scene reconstruction. The accuracy and precision of the estimated trajectories will vary depending on variables such as, the applied method of reconstruction, the (true) angle of incidence, the properties of the target material and the properties of the bullet upon impact. This study focused on the accuracy and precision of estimated bullet trajectories when different variants of the probing method, ellipse method, and lead-in method are applied on bullet defects resulting from shots at various angles of incidence on drywall, MDF and sheet metal. The results show that in most situations the best performance (accuracy and precision) is seen when the probing method is applied. Only for the lowest angles of incidence the performance was better when either the ellipse or lead-in method was applied. The data provided in this paper can be used to select the appropriate method(s) for reconstruction and to correct for systematic errors (accuracy) and to provide a value of the precision, by means of a confidence interval of the specific measurement. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Current situation and future prospects for beef production in South Korea.

PubMed

Chung, Ki Yong; Lee, Seung Hwan; Cho, Soo Hyun; Kwon, Eung Gi; Lee, Jun Heon

2018-05-31

Hanwoo cattle are an important food source in Korea and their supply can have a major impact on meat availability for Korean consumers. The Hanwoo population was 1.8 million head in 2005 and gradually increased to 2.6 million in 2015. Per capita beef consumption has also increased, to 11.6 kg per year in 2015, and is expected to continue to increase. Because intramuscular fat (IMF) percentage is a critical contributor to meat quality, Hanwoo cattle are fed a high-energy corn-based diet for long fattening periods. Long fed diet causes significant alterations in fat percentage in the loin muscle and other areas of the carcass. However, these long feeding periods increase feeding costs and beef prices. Recently, there has been increased Korean consumer demand for lean beef which has less fat, but is tender and priced more reasonably. These consumer demands on the Korean beef industry are driving differing beef production systems and also changes to the beef grading methodology. Korean government has made a significant investment to select bulls with favorable production traits using progeny testing. Progeny tested bull semen has been disseminated to all Hanwoo farmers. Beef traceability system in Korea was employed for all cattle breeds since 2009. Hanwoo cattle are ear-marked with a 12-digit identification number from birth to slaughter. This number allows traceability of the management history of individual cattle, and also provides information to consumers. Traceability including management information such as herd, farm, year of birth, and carcass data determine estimated breeding values of Hanwoo. For a sustainable Hanwoo industry, research scientists in Korea have attempted to develop feeds for efficient fattening periods and precision feeding systems based on genetic information for Hanwoo cattle. These initiatives aim to Korean consumer demands for beef and provide more precision management in beef production in Korea.

Serotonin Regulates the Feeding and Reproductive Behaviors of Pratylenchus penetrans.

PubMed

Han, Ziduan; Boas, Stephanie; Schroeder, Nathan E

2017-07-01

The success of all plant-parasitic nematodes is dependent on the completion of several complex behaviors. The lesion nematode Pratylenchus penetrans is an economically important parasite of a diverse range of plant hosts. Unlike the cyst and root-knot nematodes, P. penetrans moves both within and outside of the host roots and can feed from both locations. Adult females of P. penetrans require insemination by actively moving males for reproduction and can lay eggs both within and outside of the host roots. We do not have a complete understanding of the molecular basis for these behaviors. One candidate modulator of these behaviors is the neurotransmitter serotonin. Previous research demonstrated an effect of exogenously applied serotonin on the feeding and male mating behaviors of cyst and root-knot nematodes. However, there are no data on the role of exogenous serotonin on lesion nematodes. Similarly, there are no data on the presence and function of endogenous serotonin in any plant-parasitic nematode. Here, we establish that exogenous serotonin applied to P. penetrans regulates both feeding and sex-specific behaviors. Furthermore, using immunohistochemistry and pharmacological assays, our data suggest that P. penetrans utilizes endogenous serotonin to regulate both feeding and sex-specific behaviors.

Effect of influx on the free surface transport within a hollow ampule

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, S.C.; Vafai, K.

1994-07-01

A numerical investigation of free surface transport within a hollow glass ampule with feed-in boundary conditions is presented. The glass ampule is treated as a vertical film with a finite pressure difference across the film, with applied influx on the upper boundary, and with applied heat flux at the outer free surface. Two different sizes of glass ampules, along with different influx values are investigated. A finite element method with full consideration of surface tension and viscosity effects is used to solve the transient Navier-Stokes equations in cylindrical coordinates. Radiative and convective boundary conditions are incorporated when solving the energymore » equation. The movement of the inner and outer free surfaces with the specified feed-in velocity for different dimensions and temporal temperature distribution are analyzed. It is found that the feed-in mechanism rather than the pressure difference provides the more dominant driving forces. Also studied is the effect of using different feed-in velocities on the flow and temperature fields. The results presented in this work illustrate the basic effects of the feed-in mechanism of the free surface transport phenomenon.« less

Robotic milking: Feeding strategies and economic returns.

PubMed

Bach, Alex; Cabrera, Victor

2017-09-01

Cows in herds equipped with conventional milking parlors follow a structured, consistent, and social milking and feeding routine. Furthermore, in most cases cows in conventional herds receive all their nutrients from a total mixed ration, whereas in herds equipped with robotic or automatic milking systems (AMS) a fraction of their nutrients is provided during milking, mainly as a means to attract cows to the milking system. In this regards, AMS present both a challenge and an opportunity for feeding cows. The main challenge resides in maintaining a minimum and relatively constant milking frequency in AMS. However, milking frequency is dependent on many factors, including the social structure of the herd, the farm layout design, the type of traffic imposed to cows, the type of flooring, the health status of the cow (especially lameness, but also mastitis, metritis, among others), the stage of lactation, the parity, and the type of ration fed at the feed bunk and the concentrate offered in the AMS. Uneven milk frequency has been associated with milk losses and increased risk of mastitis, but most importantly it is a lost opportunity for milking the cow and generating profit. On the other hand, the opportunity from AMS resides in the possibility of milking more frequently and feeding cows more precisely or more closely to their nutrient needs on an individual basis, potentially resulting in a more profitable production system. But, feeding cows in the parlor or AMS has many challenges. On one side, feeding starchy, highly palatable ingredients in large amounts may upset rumen fermentation or alter feeding behavior after milking, whereas feeding high-fiber concentrates may compromise total energy intake and limit milking performance. Nevertheless, AMS (and some milking parlors, especially rotary ones) offer the possibility of feeding the cows to their estimated individual nutrient needs by combining different feeds on real time with the aim of maximizing profits rather than milk yield. This approach requires that not only the amount of feed offered to each cow but also the composition of the feed vary according to the different nutrient needs of the cows. This review discusses the opportunities and pitfalls of milking and feeding cows in an AMS and summarizes different feeding strategies to maximize profits by managing the nutrition of the cows individually. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Validation of a near infrared microscopy method for the detection of animal products in feedingstuffs: results of a collaborative study.

PubMed

Boix, A; Fernández Pierna, J A; von Holst, C; Baeten, V

2012-01-01

The performance characteristics of a near infrared microscopy (NIRM) method, when applied to the detection of animal products in feedingstuffs, were determined via a collaborative study. The method delivers qualitative results in terms of the presence or absence of animal particles in feed and differentiates animal from vegetable feed ingredients on the basis of the evaluation of near infrared spectra obtained from individual particles present in the sample. The specificity ranged from 86% to 100%. The limit of detection obtained on the analysis of the sediment fraction, prepared as for the European official method, was 0.1% processed animal proteins (PAPs) in feed, since all laboratories correctly identified the positive samples. This limit has to be increased up to 2% for the analysis of samples which are not sedimented. The required sensitivity for the official control is therefore achieved in the analysis of the sediment fraction of the samples where the method can be applied for the detection of the presence of animal meal. Criteria for the classification of samples, when fewer than five spectra are found, as being of animal origin needs to be set up in order to harmonise the approach taken by the laboratories when applying NIRM for the detection of the presence of animal meal in feed.

First light of a laser frequency comb at SALT

NASA Astrophysics Data System (ADS)

Depagne, Éric; McCracken, Richard A.; Reid, Derryck T.; Kuhn, Rudi B.; Erasmus, Nicolas; Crause, Lisa A.

2016-08-01

We present preliminary results of the commissioning and testing of SALT-CRISP (SALT-Calibration Ruler for Increased Spectrograph Precision), a Laser Frequency Comb (LFC) built by Heriot-Watt University and temporarily installed at the Southern African Large Telescope (SALT). The comb feeds the High Stability mode of SALT's High Resolution Spectrograph (HRS) and fully covers the wavelength range of the red channel of the HRS: 555-890 nm. The LFC provides significantly improved wavelength calibration compared to a standard Thorium-Argon (ThAr) lamp and hence offers unprecedented opportunities to characterise the resolution, stability and radial velocity precision of the HRS. Results from this field trial will be incorporated into subsequent LFC designs.

Molecularly imprinted solid-phase extraction for determination of tilmicosin in feed using high performance liquid chromatography.

PubMed

Zheng, Yaqiu; Liu, Yahong; Guo, Hongbin; He, Limin; Fang, Binghu; Zeng, Zhenling

2011-04-01

A simple, sensitive and reproducible molecularly imprinted solid-phase extraction (MISPE) coupled with high performance liquid chromatographic method was developed for monitoring tilmicosin in feeds. The polymers were prepared using tylosin as mimic template molecule, methacrylic acid as functional monomer and ethylene glycol dimethacrylate as cross-linking monomer, and chloroform as a solvent by bulk polymerization. Under the optimum MISPE conditions, the novel polymer sorbent can selectively extract and enrich tilmicosin from variety of feeds. The MISPE cartridge was better than non-imprinted, C(18) and HLB cartridges in terms of both recovery and precision. Mean recoveries of tilmicosin from five kinds of feeds spiked at 1, 10 and 50 mg kg(-1) ranged from 76.9% to 95.6%, with intra-day and inter-day relative standard deviation less than 7.6%. The linearity was ranged from 1.0 to 100 mg L(-1) for matrix standard solution (r=0.9990). The limit of detection was approximately 0.35 mg kg(-1) and the limit of quantification was approximately 0.98 mg kg(-1). There was cleaner chromatogram by using MISPE than C(18) and HLB SPE. Copyright © 2011 Elsevier B.V. All rights reserved.

Shared neurocircuitry underlying feeding and drugs of abuse in Drosophila.

PubMed

Landayan, Dan; Wolf, Fred W

2015-12-01

The neural circuitry and molecules that control the rewarding properties of food and drugs of abuse appear to partially overlap in the mammalian brain. This has raised questions about the extent of the overlap and the precise role of specific circuit elements in reward and in other behaviors associated with feeding regulation and drug responses. The much simpler brain of invertebrates including the fruit fly Drosophila, offers an opportunity to make high-resolution maps of the circuits and molecules that govern behavior. Recent progress in Drosophila has revealed not only some common substrates for the actions of drugs of abuse and for the regulation of feeding, but also a remarkable level of conservation with vertebrates for key neuromodulatory transmitters. We speculate that Drosophila may serve as a model for distinguishing the neural mechanisms underlying normal and pathological motivational states that will be applicable to mammals. Copyright © 2016 Chang Gung University. Published by Elsevier B.V. All rights reserved.

Propellant Feed Subsystem for a 26 kW flight arcjet propulsion system

NASA Astrophysics Data System (ADS)

Vaughan, C. E.; Morris, J. P.

1993-06-01

The USAF arcjet ATTD program demanded the development of a low-cost ammonia Propellant Feed Subsystem (PFS). A flow rate of 240 +/- 5 mg/sec during a total of ten 15-min ammonia outflows was required for the flight mission. The precision of the flow tolerance required a departure from the design of previous ammonia propellant feed systems. Since a propellant management device was not used, thermocapillary forces were explored as a means to limit outflow of liquid phase ammonia. A high energy density feedline heater with an internal wick was developed to guarantee that only gas phase propellant would reach the arcjet. A digital control algorithm was developed to implement bang-bang control of mass flow rate metered by a sonic venturi. Development tests of this system have been completed. The system is capable of continuous gas phase outflows regardless of orientation. Integrated tests with the arcjet and power conditioning unit have also been successfully completed.

KSC-08pd0037

NASA Image and Video Library

2008-01-13

KENNEDY SPACE CENTER, FLA. -- Lloyd Johns, with Lockheed Martin, prepares the area where the replacement feed-through connector in the engine cutoff, or ECO, sensor system on space shuttle Atlantis' external tank will be installed. Seen next to Johns' arm is the internal connector. The area is wrapped in material for weather protection. Berger wears safety equipment as helium gas is employed to keep the equipment under wrap dry. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The work is being done on Launch Pad 39A. Space shuttle Atlantis is now targeted for launch on Feb. 7. Photo credit: NASA/George Shelton

Incorporating a Constrained Optimization Algorithm into Remote- Sensing/Precision Agriculture Methodology

NASA Astrophysics Data System (ADS)

Morgenthaler, George; Khatib, Nader; Kim, Byoungsoo

with information to improve their crop's vigor has been a major topic of interest. With world population growing exponentially, arable land being consumed by urbanization, and an unfavorable farm economy, the efficiency of farming must increase to meet future food requirements and to make farming a sustainable occupation for the farmer. "Precision Agriculture" refers to a farming methodology that applies nutrients and moisture only where and when they are needed in the field. The goal is to increase farm revenue by increasing crop yield and decreasing applications of costly chemical and water treatments. In addition, this methodology will decrease the environmental costs of farming, i.e., reduce air, soil, and water pollution. Sensing/Precision Agriculture has not grown as rapidly as early advocates envisioned. Technology for a successful Remote Sensing/Precision Agriculture system is now available. Commercial satellite systems can image (multi-spectral) the Earth with a resolution of approximately 2.5 m. Variable precision dispensing systems using GPS are available and affordable. Crop models that predict yield as a function of soil, chemical, and irrigation parameter levels have been formulated. Personal computers and internet access are in place in most farm homes and can provide a mechanism to periodically disseminate, e.g. bi-weekly, advice on what quantities of water and chemicals are needed in individual regions of the field. What is missing is a model that fuses the disparate sources of information on the current states of the crop and soil, and the remaining resource levels available with the decisions farmers are required to make. This must be a product that is easy for the farmer to understand and to implement. A "Constrained Optimization Feed-back Control Model" to fill this void will be presented. The objective function of the model will be used to maximize the farmer's profit by increasing yields while decreasing environmental costs and decreasing application of costly treatments. This model will incorporate information from remote sensing, in-situ weather sources, soil measurements, crop models, and tacit farmer knowledge of the relative productivity of the selected control regions of the farm to provide incremental advice throughout the growing season on water and chemical treatments. Genetic and meta-heuristic algorithms will be used to solve the constrained optimization problem that possesses complex constraints and a non-linear objective function. *

21 CFR 1.328 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-04-01

... Section 1.328 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL.... Farm means a facility in one general physical location devoted to the growing and harvesting of crops...; animal feed, including pet food; food and feed ingredients and additives, including substances that...

21 CFR 1.328 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-04-01

... Section 1.328 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL.... Farm means a facility in one general physical location devoted to the growing and harvesting of crops...; animal feed, including pet food; food and feed ingredients and additives, including substances that...

21 CFR 1.328 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-04-01

... Section 1.328 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL.... Farm means a facility in one general physical location devoted to the growing and harvesting of crops...; animal feed, including pet food; food and feed ingredients and additives, including substances that...

21 CFR 1.328 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-04-01

... Section 1.328 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL.... Farm means a facility in one general physical location devoted to the growing and harvesting of crops...; animal feed, including pet food; food and feed ingredients and additives, including substances that...

KSC-08pd0072

NASA Image and Video Library

2008-01-17

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, a technician begins attaching the cover over the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0073

NASA Image and Video Library

2008-01-17

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, a technician attaches the cover over the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0069

NASA Image and Video Library

2008-01-17

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, technicians prepare the cover to be installed over the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0074

NASA Image and Video Library

2008-01-17

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, a technician completes installing the cover over the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

KSC-08pd0071

NASA Image and Video Library

2008-01-17

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, a technician gets ready to place the cover over the engine cutoff, or ECO, sensor system connector and wiring on space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

Time-delayed directional beam phased array antenna

DOEpatents

Fund, Douglas Eugene; Cable, John William; Cecil, Tony Myron

2004-10-19

An antenna comprising a phased array of quadrifilar helix or other multifilar antenna elements and a time-delaying feed network adapted to feed the elements. The feed network can employ a plurality of coaxial cables that physically bridge a microstrip feed circuitry to feed power signals to the elements. The cables provide an incremental time delay which is related to their physical lengths, such that replacing cables having a first set of lengths with cables having a second set of lengths functions to change the time delay and shift or steer the antenna's main beam. Alternatively, the coaxial cables may be replaced with a programmable signal processor unit adapted to introduce the time delay using signal processing techniques applied to the power signals.

Clinical assessment of nutritional status and feeding programs in horses.

PubMed

Becvarova, Iveta; Pleasant, R Scott; Thatcher, Craig D

2009-04-01

Veterinarians are a primary source of nutritional information and advice for horse owners. This article reviews methods for clinical assessment of nutritional status and feeding programs that can be applied to an individual horse or group of horses. Physical examination, including measurement of body weight and evaluation of body condition score, estimation of nutrient requirements and the nutrient content of the horse's diet, and evaluation of the feeding method are important components of the assessment. Ongoing clinical assessment of health and body condition will gauge the need for reassessment of the feeding plan. Obvious indications for prompt reevaluation of diet and feeding include changes in health status (eg, body condition), life stage or physiologic state (eg, pregnancy), or performance status.

Concept of a self-pressurized feed system for liquid rocket engines and its fundamental experiment results

NASA Astrophysics Data System (ADS)

Matsumoto, Jun; Okaya, Shunichi; Igoh, Hiroshi; Kawaguchi, Junichiro

2017-04-01

A new propellant feed system referred to as a self-pressurized feed system is proposed for liquid rocket engines. The self-pressurized feed system is a type of gas-pressure feed system; however, the pressurization source is retained in the liquid state to reduce tank volume. The liquid pressurization source is heated and gasified using heat exchange from the hot propellant using a regenerative cooling strategy. The liquid pressurization source is raised to critical pressure by a pressure booster referred to as a charger in order to avoid boiling and improve the heat exchange efficiency. The charger is driven by a part of the generated pressurization gas using a closed-loop self-pressurized feed system. The purpose of this study is to propose a propellant feed system that is lighter and simpler than traditional gas pressure feed systems. The proposed system can be applied to all liquid rocket engines that use the regenerative cooling strategy. The concept and mathematical models of the self-pressurized feed system are presented first. Experiment results for verification are then shown and compared with the mathematical models.

Precision Learning Assessment: An Alternative to Traditional Assessment Techniques.

ERIC Educational Resources Information Center

Caltagirone, Paul J.; Glover, Christopher E.

1985-01-01

A continuous and curriculum-based assessment method, Precision Learning Assessment (PLA), which integrates precision teaching and norm-referenced techniques, was applied to a math computation curriculum for 214 third graders. The resulting districtwide learning curves defining average annual progress through the computation curriculum provided…

Chapter 10: Precision Agriculture for Sustainability and Environmental Protection

USDA-ARS?s Scientific Manuscript database

Available supplies of water for irrigation and other uses are becoming more limited around the world, and this trend is accelerating. Emerging computerized precision irrigation technologies will enable growers to apply water and agrochemicals more precisely and site-specifically to match the status...

Lethal and sub-lethal effects of select macrocyclic lactones insecticides on forager worker honey bees under laboratory experimental conditions.

PubMed

Abdu-Allah, Gamal A M; Pittendrigh, Barry R

2018-01-01

Selective insecticide application is one important strategy for more precisely targeting harmful insects while avoiding or mitigating collateral damage to beneficial insects like honey bees. Recently, macrocyclic lactone-class insecticides have been introduced into the market place as selective bio-insecticides for controlling many arthropod pests, but how to target this selectivity only to harmful insects has yet to be achieved. In this study, the authors investigated the acute toxicity of fourmacrocyclic lactone insecticides (commercialized as abamectin, emamectin benzoate, spinetoram, and spinosad) both topically and through feeding studies with adult forager honey bees. Results indicated emamectin benzoate as topically 133.3, 750.0, and 38.3-fold and orally 3.3, 7.6, and 31.7-fold more toxic, respectively than abamectin, spinetoram and spinosad. Using Hazard Quotients for estimates of field toxicity, abamectin was measured as the safest insecticide both topically and orally for honey bees. Moreover, a significant reduction of sugar solution consumption by treatment group honey bees for orally applied emamectin benzoate and spinetoram suggests that these insecticides may have repellent properties.

Development and validation of a rapid multi-class method for the confirmation of fourteen prohibited medicinal additives in pig and poultry compound feed by liquid chromatography-tandem mass spectrometry.

PubMed

Cronly, Mark; Behan, P; Foley, B; Malone, E; Earley, S; Gallagher, M; Shearan, P; Regan, L

2010-12-01

A confirmatory method has been developed to allow for the analysis of fourteen prohibited medicinal additives in pig and poultry compound feed. These compounds are prohibited for use as feed additives although some are still authorised for use in medicated feed. Feed samples are extracted by acetonitrile with addition of sodium sulfate. The extracts undergo a hexane wash to aid with sample purification. The extracts are then evaporated to dryness and reconstituted in initial mobile phase. The samples undergo an ultracentrifugation step prior to injection onto the LC-MS/MS system and are analysed in a run time of 26 min. The LC-MS/MS system is run in MRM mode with both positive and negative electrospray ionisation. The method was validated over three days and is capable of quantitatively analysing for metronidazole, dimetridazole, ronidazole, ipronidazole, chloramphenicol, sulfamethazine, dinitolimide, ethopabate, carbadox and clopidol. The method is also capable of qualitatively analysing for sulfadiazine, tylosin, virginiamycin and avilamycin. A level of 100 microg kg(-1) was used for validation purposes and the method is capable of analysing to this level for all the compounds. Validation criteria of trueness, precision, repeatability and reproducibility along with measurement uncertainty are calculated for all analytes. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Cranial biomechanics of Diplodocus (Dinosauria, Sauropoda): testing hypotheses of feeding behaviour in an extinct megaherbivore

NASA Astrophysics Data System (ADS)

Young, Mark T.; Rayfield, Emily J.; Holliday, Casey M.; Witmer, Lawrence M.; Button, David J.; Upchurch, Paul; Barrett, Paul M.

2012-08-01

Sauropod dinosaurs were the largest terrestrial herbivores and pushed at the limits of vertebrate biomechanics and physiology. Sauropods exhibit high craniodental diversity in ecosystems where numerous species co-existed, leading to the hypothesis that this biodiversity is linked to niche subdivision driven by ecological specialisation. Here, we quantitatively investigate feeding behaviour hypotheses for the iconic sauropod Diplodocus. Biomechanical modelling, using finite element analysis, was used to examine the performance of the Diplodocus skull. Three feeding behaviours were modelled: muscle-driven static biting, branch stripping and bark stripping. The skull was found to be `over engineered' for static biting, overall experiencing low stress with only the dentition enduring high stress. When branch stripping, the skull, similarly, is under low stress, with little appreciable difference between those models. When simulated for bark stripping, the skull experiences far greater stresses, especially in the teeth and at the jaw joint. Therefore, we refute the bark-stripping hypothesis, while the hypotheses of branch stripping and/or precision biting are both consistent with our findings, showing that branch stripping is a biomechanically plausible feeding behaviour for diplodocids. Interestingly, in all simulations, peak stress is observed in the premaxillary-maxillary `lateral plates', supporting the hypothesis that these structures evolved to dissipate stress induced while feeding. These results lead us to conclude that the aberrant craniodental form of Diplodocus was adapted for food procurement rather than resisting high bite forces.

Genetic parameters of pelt character, feed efficiency and size traits in Finnish blue fox (Vulpes lagopus).

PubMed

Kempe, R; Koskinen, N; Strandén, I

2013-12-01

Pelt character traits (size, quality, colour clarity, darkness) are important economic traits in blue fox breeding. Better feed efficiency (FE) is another economically important and new breeding goal for fur animals. The purpose of this study was to determine the correlations between pelt character traits, FE and size traits and to estimate genetic parameters for pelt character traits. Pelt size (pSIcm ) had a high positive genetic correlation with animal grading size (gSI), final body weight (BWFin), body length and daily gain (DG), and a moderate correlation with body condition score (BCS). Animal body length and BCS (describing fatness) were considered as genetically different traits. Genetic correlations between pelt quality and size traits were estimated without precision and did not differ from zero, but colour clarity (pCL) had a low antagonistic genetic correlation with FE. Pelt size and DG had a favourable genetic correlation with FE but a fairly high unfavourable genetic correlation with dry matter feed intake. The current emphasis on selection for larger animal and pelt size improves FE indirectly, but selection for larger pelt size favours fast-growing and fat individuals and simultaneously increases feed intake. The detected genetic connections between FE, size, feed intake and pCL should be taken into account in the Finnish blue fox breeding programme. © 2013 Blackwell Verlag GmbH.

Feeding behavior improves prediction of dairy cow voluntary feed intake but cannot serve as the sole indicator.

PubMed

Halachmi, I; Ben Meir, Y; Miron, J; Maltz, E

2016-09-01

Low-cost feeding-behavior sensors will soon be available for commercial use in dairy farms. The aim of this study was to develop a feed intake model for the individual dairy cow that includes feeding behavior. In a research farm, the individual cows' voluntary feed intake and feeding behavior were monitored at every meal. A feed intake model was developed based on data that exist in commercial modern farms: 'BW,' 'milk yield' and 'days in milking' parameters were applied in this study. At the individual cow level, eating velocity seemed to be correlated with feed intake (R 2=0.93 to 0.94). The eating velocity coefficient varied among individuals, ranging from 150 to 230 g/min per cow. The contribution of feeding behavior (0.28) to the dry matter intake (DMI) model was higher than the contribution of BW (0.20), similar to the contribution of fat-corrected milk (FCM)/BW (0.29) and not as large as the contribution of FCM (0.49). Incorporating feeding behavior into the DMI model improved its accuracy by 1.3 (38%) kg/cow per day. The model is ready to be implemented in commercial farms as soon as companies introduce low-cost feeding-behavior sensors on commercial level.

Monitoring utilizations of amino acids and vitamins in culture media and Chinese hamster ovary cells by liquid chromatography tandem mass spectrometry.

PubMed

Qiu, Jinshu; Chan, Pik Kay; Bondarenko, Pavel V

2016-01-05

Monitoring amino acids and vitamins is important for understanding human health, food nutrition and the culture of mammalian cells used to produce therapeutic proteins in biotechnology. A method including ion pairing reversed-phase liquid chromatography with tandem mass spectrometry was developed and optimized to quantify 21 amino acids and 9 water-soluble vitamins in Chinese hamster ovary (CHO) cells and culture media. By optimizing the chromatographic separation, scan time, monitoring time window, and sample preparation procedure, and using isotopically labeled (13)C, (15)N and (2)H internal standards, low limits of quantitation (≤0.054 mg/L), good precision (<10%) and good accuracy (100±10%) were achieved for nearly all the 30 compounds. Applying this method to CHO cell extracts, statistically significant differences in the metabolite levels were measured between two cell lines originated from the same host, indicating differences in genetic makeup or metabolic activities and nutrient supply levels in the culture media. In a fed-batch process of manufacturing scale bioreactors, two distinguished trends for changes in amino acid concentrations were identified in response to feeding. Ten essential amino acids showed a zigzag pattern with maxima at the feeding days, and 9 non-essential amino acids displayed a smoothly changing profile as they were mainly products of cellular metabolism. Five of 9 vitamins accumulated continuously during the culture period, suggesting that they were fed in access. The method serves as an effective tool for the development and optimization of mammalian cell cultures. Copyright © 2015 Elsevier B.V. All rights reserved.

Metal alloy coatings and methods for applying

DOEpatents

Merz, Martin D.; Knoll, Robert W.

1991-01-01

A method of coating a substrate comprises plasma spraying a prealloyed feed powder onto a substrate, where the prealloyed feed powder comprises a significant amount of an alloy of stainless steel and at least one refractory element selected from the group consisting of titanium, zirconium, hafnium, niobium, tantalum, molybdenum, and tungsten. The plasma spraying of such a feed powder is conducted in an oxygen containing atmosphere and forms an adherent, corrosion resistant, and substantially homogenous metallic refractory alloy coating on the substrate.

Breast-fed infants and their later cardiovascular health: a prospective study from birth to age 32 years.

PubMed

Pirilä, Satu; Taskinen, Mervi; Viljakainen, Heli; Mäkitie, Outi; Kajosaari, Merja; Saarinen-Pihkala, Ulla M; Turanlahti, Maila

2014-03-28

The aim of the present study was to evaluate the impact of infant breast-feeding on cardiovascular risk in young adults. This unique study group involved 158 subjects (eighty-two females) originally collected prospectively at birth in 1975 and followed up to the age of 32 years. Frequent visits during the first year guaranteed the knowledge of the precise duration of breast-feeding. All infants received at least some breast milk. Participants were assessed for both individual cardiovascular risk factors (blood pressure, plasma lipids, homeostatic model assessment of insulin resistance and waist circumference) and the general clinical risk of cardiovascular events by calculating the Framingham risk score (FRS) and the metabolic syndrome criteria score (NCEP-ATPIII; National Cholesterol Education Program's Adult Treatment Panel III). Data on lifestyle factors were carefully collected. Linear regression analyses revealed that the effect of the duration of breast-feeding was not relevant (0·02 decrease in the FRS per one additional breast-feeding month; 95 % CI - 0·19, 0·09). Similarly, the effect of breast-feeding was minor on all of the individual cardiovascular risk factors. We used sex, physical activity, dietary fat and vitamin C, smoking and alcohol consumption as covariates. Again, logistic regression analyses detected no significant impact of the duration of breast-feeding on the risk of the metabolic syndrome according to the NCEP-ATPIII (OR 0·95, 95 % CI 0·8, 1·1). The strongest independent predictor for later CVD risk was male sex. In conclusion, in this prospectively followed cohort of young adults born at term and at weight appropriate for gestational age, the duration of breast-feeding did not have an impact on the accumulation of cardiovascular risk factors.

Single nucleotide polymorphisms and haplotypes associated with feed efficiency in beef cattle

PubMed Central

2013-01-01

Background General, breed- and diet-dependent associations between feed efficiency in beef cattle and single nucleotide polymorphisms (SNPs) or haplotypes were identified on a population of 1321 steers using a 50 K SNP panel. Genomic associations with traditional two-step indicators of feed efficiency – residual feed intake (RFI), residual average daily gain (RADG), and residual intake gain (RIG) – were compared to associations with two complementary one-step indicators of feed efficiency: efficiency of intake (EI) and efficiency of gain (EG). Associations uncovered in a training data set were evaluated on independent validation data set. A multi-SNP model was developed to predict feed efficiency. Functional analysis of genes harboring SNPs significantly associated with feed efficiency and network visualization aided in the interpretation of the results. Results For the five feed efficiency indicators, the numbers of general, breed-dependent, and diet-dependent associations with SNPs (P-value < 0.0001) were 31, 40, and 25, and with haplotypes were six, ten, and nine, respectively. Of these, 20 SNP and six haplotype associations overlapped between RFI and EI, and five SNP and one haplotype associations overlapped between RADG and EG. This result confirms the complementary value of the one and two-step indicators. The multi-SNP models included 89 SNPs and offered a precise prediction of the five feed efficiency indicators. The associations of 17 SNPs and 7 haplotypes with feed efficiency were confirmed on the validation data set. Nine clusters of Gene Ontology and KEGG pathway categories (mean P-value < 0.001) including, 9nucleotide binding; ion transport, phosphorous metabolic process, and the MAPK signaling pathway were overrepresented among the genes harboring the SNPs associated with feed efficiency. Conclusions The general SNP associations suggest that a single panel of genomic variants can be used regardless of breed and diet. The breed- and diet-dependent associations between SNPs and feed efficiency suggest that further refinement of variant panels require the consideration of the breed and management practices. The unique genomic variants associated with the one- and two-step indicators suggest that both types of indicators offer complementary description of feed efficiency that can be exploited for genome-enabled selection purposes. PMID:24066663

Feeding behavior of the stink bug Bagrada hilaris is changed by the electrical signals applied during EPG recordings

USDA-ARS?s Scientific Manuscript database

Feeding behavior of piercing-sucking insects is most rigorously studied using eletropenetrography (EPG). This technique utilizes an electrical circuit to record waveforms caused by voltage fluctuations when a wired insect inserts its stylet into an electrified plant. Past researchers have asserted t...

7 CFR 760.206 - Notice of loss and application process.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., Honeybees, and Farm-Raised Fish Program § 760.206 Notice of loss and application process. (a) To apply for ELAP, the participant that suffered eligible livestock, honeybee, or farm-raised fish losses must... Application; (ii) For honeybee feed, honeybee colony, honeybee hive, or farm-raised fish feed or death losses...

The Impact of Chile's School Feeding Program on Education Outcomes

ERIC Educational Resources Information Center

McEwan, Patrick J.

2013-01-01

Chile operates one of the oldest and largest school feeding programs in Latin America, targeting higher-calorie meals to relatively poorer schools. This paper evaluates the impact of higher-calorie meals on the education outcomes of public, rural schools and their students. It applies a regression-discontinuity design to administrative data,…

75 FR 44184 - Aluminum tris(O-ethylphosphonate), Butylate, Chlorethoxyfos, Clethodim, et al.; Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-28

...: Crop production (NAICS code 111). Animal production (NAICS code 112). Food manufacturing (NAICS code... contamination of food, feed, or food-contact/feed-contact surfaces. Compliance with the tolerance level... Apply to Me? You may be potentially affected by this action if you are an agricultural producer, food...

Artificial feeding of Varroa destructor through a chitosan membrane: a tool for studying the host-microparasite relationship.

PubMed

Tabart, Jeremy; Colin, Marc-Edouard; Carayon, Jean-Luc; Tene, Nathan; Payre, Bruno; Vetillard, Angelique

2013-09-01

Rearing pests or parasites of very small size in the absence of their living host is a challenge for behavioural, physiological and pathological studies. For feeding Varroa destructor, an ectoparasitic mite of Apis mellifera, a confinement space with a membrane separating the nutritive solution and the space was designed. The mite measures less than 2 mm and bears a perforating apparatus with a length of 15 μm. The membrane, an essential element of the chamber, has a thickness of 0.1 μm, and is made of chitosan. It closes one face of the individual confinement chamber and allows piercing and the ingestion of the nutritive solution. Factors inducing feeding can be applied on the inner walls or on the membrane. In the particular case of Varroa, the highest percentages of feeding mites are obtained by addition of host haemolymph to the nutritive solution, suggesting the kairomonal role of haemolymph in addition to its nutritional one. The membrane concept can be easily applied to several mites or other micro-pests.

Feed network and electromagnetic radiation source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ardavan, Arzhang; Singleton, John; Linehan, Kevin E.

An antenna may include a volume polarization current radiator and a feed network. The volume polarization current radiator, includes a dielectric solid (such as a dielectric strip), and a plurality of closely-spaced excitation elements (24), each excitation element (24) being configured to induce a volume polarization current distribution in the dielectric solid proximate to the excitation element when a voltage is applied to the excitation element. The feed network is coupled to the volume polarization current radiator. The feed network also includes a plurality of passive power divider elements (32) and a plurality of passive delay elements (d1-d6) coupling themore » first port (30) and the plurality of second ports (108, 109, 164), the plurality of power divider elements (32) and the plurality of phase delay elements (d1-d6) being configured such that a radio-frequency signal that is applied to the first port (30) experiences a progressive change of phase as it is coupled to the plurality of second ports (108, 109, 164) so as to cause the volume polarization current distribution to propagate along the dielectric solid.« less

Habituation in Frankliniella occidentalis to deterrent plant compounds and their blends.

PubMed

Egger, Barbara; Spangl, Bernhard; Koschier, Elisabeth Helene

2014-06-01

Feeding and oviposition deterrence of three secondary plant compounds and their 1:1 blends to adult female Frankliniella occidentalis Pergande (Thysanoptera: Thripidae) and the potential for habituation of the thrips to the pure compounds and the 1:1 blends at various concentrations were investigated. In choice assays, we tested dose-dependent feeding and oviposition deterrence of the two fatty acid derivatives methyl jasmonate and cis -jasmone, the phenylpropanoid allylanisole, and their blends when directly applied to bean leaf discs. The concentration required to reduce the feeding damage by 50% relative to the control treatment (FDC 50 ) was lowest for cis -jasmone and highest for allylanisole. The feeding deterrent effect of both jasmonates was increased when blended with allylanisole. Feeding deterrence and oviposition deterrence were strongly correlated. In no-choice assays conducted over four consecutive days, we discovered that dilutions at low concentrations (FDC 15 ) applied to bean leaves resulted in habituation to the deterrents, whereas no habituation occurred at higher concentrations (FDC 50 ). We observed a tendency that the 1:1 blends reduce the probability that thrips habituate to the deterrent compounds. Our results may be useful in the development of integrated crop protection strategies with the implementation of allelochemicals as pest behaviour-modifying agents.

Effect of water activity and temperature on the growth of Eurotium species isolated from animal feeds.

PubMed

Greco, Mariana; Pardo, Alejandro; Pose, Graciela; Patriarca, Andrea

Xerophilic fungi represent a serious problem due to their ability to grow at low water activities causing the spoiling of low and intermediate moisture foods, stored goods and animal feeds, with the consequent economic losses. The combined effect of water activity and temperature of four Eurotium species isolated from animal feeds was investigated. Eurotium amstelodami, Eurotium chevalieri, Eurotium repens and Eurotium rubrum were grown at 5, 15, 25, 37 and 45°C on malt extract agar adjusted with glycerol in the range 0.710-0.993 of water activities. The cardinal model proposed by Rosso and Robinson (2001) was applied to fit growth data, with the variable water activity at fixed temperatures, obtaining three cardinal water activities (a wmin , a wmax , a wopt ) and the specific growth rate at the optimum a w (μ opt ). A probabilistic model was also applied to define the interface between growth and no-growth. The cardinal model provided an adequate estimation of the optimal a w to grow and the maximum growth rate. The probabilistic model showed a good performance to fit growth/no-growth cases in the predicted range. The results presented here could be applied to predict Eurotium species growth in animal feeds. Copyright © 2017 Asociación Española de Micología. Publicado por Elsevier España, S.L.U. All rights reserved.

Safety Assessment of Food and Feed from GM Crops in Europe: Evaluating EFSA's Alternative Framework for the Rat 90-day Feeding Study.

PubMed

Hong, Bonnie; Du, Yingzhou; Mukerji, Pushkor; Roper, Jason M; Appenzeller, Laura M

2017-07-12

Regulatory-compliant rodent subchronic feeding studies are compulsory regardless of a hypothesis to test, according to recent EU legislation for the safety assessment of whole food/feed produced from genetically modified (GM) crops containing a single genetic transformation event (European Union Commission Implementing Regulation No. 503/2013). The Implementing Regulation refers to guidelines set forth by the European Food Safety Authority (EFSA) for the design, conduct, and analysis of rodent subchronic feeding studies. The set of EFSA recommendations was rigorously applied to a 90-day feeding study in Sprague-Dawley rats. After study completion, the appropriateness and applicability of these recommendations were assessed using a battery of statistical analysis approaches including both retrospective and prospective statistical power analyses as well as variance-covariance decomposition. In the interest of animal welfare considerations, alternative experimental designs were investigated and evaluated in the context of informing the health risk assessment of food/feed from GM crops.

Crop Yield Predictions - High Resolution Statistical Model for Intra-season Forecasts Applied to Corn in the US

NASA Astrophysics Data System (ADS)

Cai, Y.

2017-12-01

Accurately forecasting crop yields has broad implications for economic trading, food production monitoring, and global food security. However, the variation of environmental variables presents challenges to model yields accurately, especially when the lack of highly accurate measurements creates difficulties in creating models that can succeed across space and time. In 2016, we developed a sequence of machine-learning based models forecasting end-of-season corn yields for the US at both the county and national levels. We combined machine learning algorithms in a hierarchical way, and used an understanding of physiological processes in temporal feature selection, to achieve high precision in our intra-season forecasts, including in very anomalous seasons. During the live run, we predicted the national corn yield within 1.40% of the final USDA number as early as August. In the backtesting of the 2000-2015 period, our model predicts national yield within 2.69% of the actual yield on average already by mid-August. At the county level, our model predicts 77% of the variation in final yield using data through the beginning of August and improves to 80% by the beginning of October, with the percentage of counties predicted within 10% of the average yield increasing from 68% to 73%. Further, the lowest errors are in the most significant producing regions, resulting in very high precision national-level forecasts. In addition, we identify the changes of important variables throughout the season, specifically early-season land surface temperature, and mid-season land surface temperature and vegetation index. For the 2017 season, we feed 2016 data to the training set, together with additional geospatial data sources, aiming to make the current model even more precise. We will show how our 2017 US corn yield forecasts converges in time, which factors affect the yield the most, as well as present our plans for 2018 model adjustments.

Precision stellar radial velocity measurements with FIDEOS at the ESO 1-m telescope of La Silla

NASA Astrophysics Data System (ADS)

Vanzi, L.; Zapata, A.; Flores, M.; Brahm, R.; Tala Pinto, M.; Rukdee, S.; Jones, M.; Ropert, S.; Shen, T.; Ramirez, S.; Suc, V.; Jordán, A.; Espinoza, N.

2018-07-01

We present results from the commissioning and early science programs of FIbre Dual Echelle Optical Spectrograph (FIDEOS), the new high-resolution echelle spectrograph developed at the Centre of Astro Engineering of Pontificia Universidad Catolica de Chile, and recently installed at the ESO 1-m telescope of La Silla. The instrument provides spectral resolution R ˜ 43 000 in the visible spectral range 420-800 nm, reaching a limiting magnitude of 11 in V band. Precision in the measurement of radial velocity is guaranteed by light feeding with an octagonal optical fibre, suitable mechanical isolation, thermal stabilization, and simultaneous wavelength calibration. Currently the instrument reaches radial velocity stability of ˜8 m s-1 over several consecutive nights of observation.

A flux calibration device for the SuperNova Integral Field Spectrograph (SNIFS)

NASA Astrophysics Data System (ADS)

Lombardo, Simona; Aldering, Greg; Hoffmann, Akos; Kowalski, Marek; Kuesters, Daniel; Reif, Klaus; Rigault, Michael

2014-07-01

Observational cosmology employing optical surveys often require precise flux calibration. In this context we present SNIFS Calibration Apparatus (SCALA), a flux calibration system developed for the SuperNova Integral Field Spectrograph (SNIFS), operating at the University of Hawaii 2.2 m telescope. SCALA consists of a hexagonal array of 18 small parabolic mirrors distributed over the face of, and feeding parallel light to, the telescope entrance pupil. The mirrors are illuminated by integrating spheres and a wavelength-tunable (from UV to IR) light source, generating light beams with opening angles of 1°. These nearly parallel beams are flat and flux-calibrated at a subpercent level, enabling us to calibrate our "telescope + SNIFS system" at the required precision.

ZERODUR expanding capabilities and capacity for future spaceborne and ground-based telescopes

NASA Astrophysics Data System (ADS)

Westerhoff, Thomas; Werner, Thomas

2017-09-01

The glass ceramic ZERODUR is well known for its extremely low coefficient of thermal expansion making it one of the key materials for ultra-precision application such as IC and LCD Lithography, High-end Metrology, Aviation and space borne or ground based Astronomy. The steady growth of demand for more precision in those applications together with a growing number of precision systems and components is requesting the ability to on hand increase precision in manufacturing. Additionally, there is a need to increase production capacity of ZERODUR CNC machined products in parallel. This paper reports on the measures SCHOTT is realizing to feed the continuously increasing demand on high precision material and components. Next to a second melting tank additional capacity is going to be installed along the entire value stream of ZERODUR production. Features of new CNC machining capabilities in the two and four meter class will be reported allowing to provide tighter tolerance on mirror surface figure together with reduced sub surface damage in order to accelerate the polishing time. Examples are discussed such as the 4 m class secondary and tertiary mirrors for the ESO E-ELT. The new equipment will enable SCHOTT to light weight 4 m class mirror substrates for future space optics demand.

Pediatricians', obstetricians', gynecologists', and family medicine physicians' experiences with and attitudes about breast-feeding.

PubMed

Anchondo, Inés; Berkeley, Lizabeth; Mulla, Zuber D; Byrd, Theresa; Nuwayhid, Bahij; Handal, Gilbert; Akins, Ralitsa

2012-05-01

Investigate physicians' breast-feeding experiences and attitudes using a survey based on two behavioral theories: theory of reasoned action (TRA) and the health belief model (HBM). There were 73 participants included in the investigation. These participants were resident and faculty physicians from pediatrics, obstetrics/gynecology, and family medicine at a university campus, located on the US-Mexico border. The sample was reduced to 53 and 56 records for the attitude and confidence variables, respectively. Physicians answered a survey about their breast-feeding experiences and attitudes to learn about intention and ability applying constructs from TRA and HBM. An attitude scale, confidence variable (from self-efficacy items), and a lactation training index were created for the analysis. Analysis of the association between physicians' breastfeeding experiences and their attitudes revealed physicians are knowledgeable about breast-feeding and have positive attitudes towards breast-feeding. They did not seem to remember how long they breast-fed their children or whether they enjoyed breast-feeding, but they wanted to continue breast-feeding. Physicians cite work as a main reason for not continuing to breast-feed. Physicians' attitudes toward breast-feeding are positive. They are expected to practice health-promotion behavior including breast-feeding; however, physicians' breast-feeding rates are low and although they are knowledgeable about breast-feeding their training lacks on didactic depth and hands-on experience. If physicians learn more about breast-feeding and breast-feed exclusively and successfully, the rates in the United States would increase naturally.

The importance of hormonal circadian rhythms in daily feeding patterns: An illustration with simulated pigs.

PubMed

Boumans, Iris J M M; de Boer, Imke J M; Hofstede, Gert Jan; la Fleur, Susanne E; Bokkers, Eddie A M

2017-07-01

The interaction between hormonal circadian rhythms and feeding behaviour is not well understood. This study aimed to deepen our understanding of mechanisms underlying circadian feeding behaviour in animals, using pigs, Sus scrofa, as a case study. Pigs show an alternans feeding pattern, that is, a small peak of feed intake at the beginning of the day and a larger peak at the end of the day. We simulated the feeding behaviour of pigs over a 24h period. The simulation model contained mechanisms that regulate feeding behaviour of animals, including: processing of feed in the gastrointestinal tract, fluctuation in energy balance, circadian rhythms of melatonin and cortisol and motivational decision-making. From the interactions between these various processes, feeding patterns (e.g. feed intake, meal frequency, feeding rate) emerge. These feeding patterns, as well as patterns for the underlying mechanisms (e.g. energy expenditure), fitted empirical data well, indicating that our model contains relevant mechanisms. The circadian rhythms of cortisol and melatonin explained the alternans pattern of feeding in pigs. Additionally, the timing and amplitude of cortisol peaks affected the diurnal and nocturnal peaks in feed intake. Furthermore, our results suggest that circadian rhythms of other hormones, such as leptin and ghrelin, are less important in circadian regulation of feeding behaviour than previously thought. These results are relevant to animal species with a metabolic and endocrine system similar to that of pigs, such as humans. Moreover, the modelling approach to understand feeding behaviour can be applied to other animal species. Copyright © 2017 Elsevier Inc. All rights reserved.

Modeling of membrane processes for air revitalization and water recovery

NASA Technical Reports Server (NTRS)

Lange, Kevin E.; Foerg, Sandra L.; Dall-Bauman, Liese A.

1992-01-01

Gas-separation and reverse-osmosis membrane models are being developed in conjunction with membrane testing at NASA JSC. The completed gas-separation membrane model extracts effective component permeabilities from multicomponent test data, and predicts the effects of flow configuration, operating conditions, and membrane dimensions on module performance. Variable feed- and permeate-side pressures are considered. The model has been applied to test data for hollow-fiber membrane modules with simulated cabin-air feeds. Results are presented for a membrane designed for air drying applications. Extracted permeabilities are used to predict the effect of operating conditions on water enrichment in the permeate. A first-order reverse-osmosis model has been applied to test data for spiral wound membrane modules with a simulated hygiene water feed. The model estimates an effective local component rejection coefficient under pseudosteady-state conditions. Results are used to define requirements for a detailed reverse-osmosis model.

Grinding Method and Error Analysis of Eccentric Shaft Parts

NASA Astrophysics Data System (ADS)

Wang, Zhiming; Han, Qiushi; Li, Qiguang; Peng, Baoying; Li, Weihua

2017-12-01

RV reducer and various mechanical transmission parts are widely used in eccentric shaft parts, The demand of precision grinding technology for eccentric shaft parts now, In this paper, the model of X-C linkage relation of eccentric shaft grinding is studied; By inversion method, the contour curve of the wheel envelope is deduced, and the distance from the center of eccentric circle is constant. The simulation software of eccentric shaft grinding is developed, the correctness of the model is proved, the influence of the X-axis feed error, the C-axis feed error and the wheel radius error on the grinding process is analyzed, and the corresponding error calculation model is proposed. The simulation analysis is carried out to provide the basis for the contour error compensation.

Quantifying Drosophila food intake: comparative analysis of current methodology

PubMed Central

Deshpande, Sonali A.; Carvalho, Gil B.; Amador, Ariadna; Phillips, Angela M.; Hoxha, Sany; Lizotte, Keith J.; Ja, William W.

2014-01-01

Food intake is a fundamental parameter in animal studies. Despite the prevalent use of Drosophila in laboratory research, precise measurements of food intake remain challenging in this model organism. Here, we compare several common Drosophila feeding assays: the Capillary Feeder (CAFE), food-labeling with a radioactive tracer or a colorimetric dye, and observations of proboscis extension (PE). We show that the CAFE and radioisotope-labeling provide the most consistent results, have the highest sensitivity, and can resolve differences in feeding that dye-labeling and PE fail to distinguish. We conclude that performing the radiolabeling and CAFE assays in parallel is currently the best approach for quantifying Drosophila food intake. Understanding the strengths and limitations of food intake methodology will greatly advance Drosophila studies of nutrition, behavior, and disease. PMID:24681694

Fiber feed for the CFHT Gecko spectrograph

NASA Astrophysics Data System (ADS)

Baudrand, Jacques; Vitry, Rene

2000-08-01

Motivated by a strong concern to keep maintenance work as low as possible the direction of the CFHT had for some times contemplated the possibility to replace the original mirror train f/20 focus feeding their Gecko High Resolution Coude Spectrograph by a more convenient fiber link coupled to the f/8 Cassegrain focus. A decision supporting that idea was ultimately taken two years ago and our group at the OPM was contacted to build such a system according to precise specifications. This telescope facility, baptized CAFÉ for Cassegrain Fiber Environment, has now arrived to near completion and we are able to present here its main characteristics and the technical solutions that were adopted to meet the CFHT requirements and to provide the system with the best performances in terms of robustness and efficiency.

KSC-08pd0070

NASA Image and Video Library

2008-01-17

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A at NASA's Kennedy Space Center, technicians prepare the cover to be installed over the engine cutoff, or ECO, sensor system connector and wiring on space shuttle space shuttle Atlantis' external tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Kim Shiflett

The in ovo feeding administration (gallus gallus)-an emerging in vivo approach to assess bioactive compounds with potential nutritional benefits

USDA-ARS?s Scientific Manuscript database

In recent years, the in ovo feeding in fertilized broiler (Gallus gallus) eggs approach was further developed and currently is widely applied in the evaluation process of the effects of functional foods (primarily plant origin compounds) on the functionality of the intestinal brush border membrane, ...

40 CFR 503.11 - Special definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Agricultural land is land on which a food crop, a feed crop, or a fiber crop is grown. This includes range land...) designed: (1) To provide the amount of nitrogen needed by the food crop, feed crop, fiber crop, cover crop... applied to an area of land. (g) Forest is a tract of land thick with trees and underbrush. (h) Land...

40 CFR 503.11 - Special definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Agricultural land is land on which a food crop, a feed crop, or a fiber crop is grown. This includes range land...) designed: (1) To provide the amount of nitrogen needed by the food crop, feed crop, fiber crop, cover crop... applied to an area of land. (g) Forest is a tract of land thick with trees and underbrush. (h) Land...

40 CFR 503.11 - Special definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Agricultural land is land on which a food crop, a feed crop, or a fiber crop is grown. This includes range land...) designed: (1) To provide the amount of nitrogen needed by the food crop, feed crop, fiber crop, cover crop... applied to an area of land. (g) Forest is a tract of land thick with trees and underbrush. (h) Land...

Effect of non-feeding period length on the intermittent operation of UASB reactors treating dairy effluents.

PubMed

Coelho, N M; Rodrigues, A A; Arroja, L M; Capela, I F

2007-02-01

Recent environmental concerns have prompted a re-evaluation of conventional management strategies and refueled the search of innovative waste management practices. In this sense, the anaerobic digestion of both fat and the remaining complex organic matter present in dairy wastewaters is attractive, although the continuous operation of high rate anaerobic processes treating this type of wastewaters causes the failure of the process. This work accesses the influence of non-feeding period length on the intermittent operation of mesophilic UASB reactors treating dairy wastewater, in order to allow the biological degradation to catch up with adsorption phenomenon. During the experiments, two UASB reactors were subject to three organic loading rates, ranging from 6 to 12 g(COD) x L(-1) x d(-1), with the same daily load applied to both reactors, each one with a different non-feeding period. Both reactors showed good COD removal efficiencies (87-92%). A material balance for COD in the reactors during the feeding and non-feeding periods showed the importance of the feedless period, which allowed the biomass to degrade substrate that was accumulated during the feeding period. The reactor with the longest non-feeding period had a better performance, which resulted in a higher methane production and adsorption capacity for the same organic load applied with a consequent less accumulation of substrate into the biomass. In addition, both reactors had a stable operation for the organic load of 12 g(COD) x L(-1) x d(-1), which is higher than the maximum applicable load reported in literature for continuous systems (3-6 g(COD) x L(-1) x d(-1)). (c) 2006 Wiley Periodicals, Inc.

Application of Artificial Neural Network and Support Vector Machines in Predicting Metabolizable Energy in Compound Feeds for Pigs.

PubMed

Ahmadi, Hamed; Rodehutscord, Markus

2017-01-01

In the nutrition literature, there are several reports on the use of artificial neural network (ANN) and multiple linear regression (MLR) approaches for predicting feed composition and nutritive value, while the use of support vector machines (SVM) method as a new alternative approach to MLR and ANN models is still not fully investigated. The MLR, ANN, and SVM models were developed to predict metabolizable energy (ME) content of compound feeds for pigs based on the German energy evaluation system from analyzed contents of crude protein (CP), ether extract (EE), crude fiber (CF), and starch. A total of 290 datasets from standardized digestibility studies with compound feeds was provided from several institutions and published papers, and ME was calculated thereon. Accuracy and precision of developed models were evaluated, given their produced prediction values. The results revealed that the developed ANN [ R 2  = 0.95; root mean square error (RMSE) = 0.19 MJ/kg of dry matter] and SVM ( R 2  = 0.95; RMSE = 0.21 MJ/kg of dry matter) models produced better prediction values in estimating ME in compound feed than those produced by conventional MLR ( R 2  = 0.89; RMSE = 0.27 MJ/kg of dry matter). The developed ANN and SVM models produced better prediction values in estimating ME in compound feed than those produced by conventional MLR; however, there were not obvious differences between performance of ANN and SVM models. Thus, SVM model may also be considered as a promising tool for modeling the relationship between chemical composition and ME of compound feeds for pigs. To provide the readers and nutritionist with the easy and rapid tool, an Excel ® calculator, namely, SVM_ME_pig, was created to predict the metabolizable energy values in compound feeds for pigs using developed support vector machine model.

Enhancement of L-Threonine Production by Controlling Sequential Carbon-Nitrogen Ratios during Fermentation.

PubMed

Lee, Hyeok-Won; Lee, Hee-Suk; Kim, Chun-Suk; Lee, Jin-Gyeom; Kim, Won-Kyo; Lee, Eun-Gyo; Lee, Hong-Weon

2018-02-28

Controlling the residual glucose concentration is important for improving productivity in L-threonine fermentation. In this study, we developed a procedure to automatically control the feeding quantity of glucose solution as a function of ammonia-water consumption rate. The feeding ratio (R C/N ) of glucose and ammonia water was predetermined via a stoichiometric approach, on the basis of glucose-ammonia water consumption rates. In a 5-L fermenter, 102 g/l L -threonine was obtained using our glucose-ammonia water combined feeding strategy, which was then successfully applied in a 500-L fermenter (89 g/l). Therefore, we conclude that an automatic combination feeding strategy is suitable for improving L-threonine production.

A farm-level precision land management framework based on integer programming

PubMed Central

Li, Qi; Hu, Guiping; Jubery, Talukder Zaki; Ganapathysubramanian, Baskar

2017-01-01

Farmland management involves several planning and decision making tasks including seed selection and irrigation management. A farm-level precision farmland management model based on mixed integer linear programming is proposed in this study. Optimal decisions are designed for pre-season planning of crops and irrigation water allocation. The model captures the effect of size and shape of decision scale as well as special irrigation patterns. The authors illustrate the model with a case study on a farm in the state of California in the U.S. and show the model can capture the impact of precision farm management on profitability. The results show that threefold increase of annual net profit for farmers could be achieved by carefully choosing irrigation and seed selection. Although farmers could increase profits by applying precision management to seed or irrigation alone, profit increase is more significant if farmers apply precision management on seed and irrigation simultaneously. The proposed model can also serve as a risk analysis tool for farmers facing seasonal irrigation water limits as well as a quantitative tool to explore the impact of precision agriculture. PMID:28346499

Dynamic Stability and Gravitational Balancing of Multiple Extended Bodies

NASA Technical Reports Server (NTRS)

Quadrelli, Marco

2008-01-01

Feasibility of a non-invasive compensation scheme was analyzed for precise positioning of a massive extended body in free fall using gravitational forces influenced by surrounding source masses in close proximity. The N-body problem of classical mechanics is a paradigm used to gain insight into the physics of the equivalent N-body problem subject to control forces. The analysis addressed how a number of control masses move around the proof mass so that the proof mass position can be accurately and remotely compensated when exogenous disturbances are acting on it, while its sensitivity to gravitational waves remains unaffected. Past methods to correct the dynamics of the proof mass have considered active electrostatic or capacitive methods, but the possibility of stray capacitances on the surfaces of the proof mass have prompted the investigation of other alternatives, such as the method presented in this paper. While more rigorous analyses of the problem should be carried out, the data show that, by means of a combined feedback and feed-forward control approach, the control masses succeeded in driving the proof mass along the specified trajectory, which implies that the proof mass can, in principle, be balanced via gravitational forces only while external perturbations are acting on it. This concept involves the dynamic stability of a group of massive objects interacting gravitationally under active control, and can apply to drag-free control of spacecraft during missions, to successor gravitational wave space borne sensors, or to any application requiring flying objects to be precisely controlled in position and attitude relative to another body via gravitational interactions only.

Influence of coolant on ductile mode processing of binderless nanocrystalline tungsten carbide through ultraprecision diamond turning

NASA Astrophysics Data System (ADS)

Doetz, Marius; Dambon, Olaf; Klocke, Fritz; Fähnle, Oliver

2015-08-01

Molds made of tungsten carbide are typically used for the replicative mass production of glass lenses by precision glass molding. Consequently an ultra-precision grinding process with a subsequent fresh-feed polishing operation is conventionally applied. These processes are time consuming and have a relatively low reproducibility. An alternative manufacturing technology, with a high predictability and efficiency, which additionally allows a higher geometrical flexibility, is the single point diamond turning technique (SPDT). However, the extreme hardness and the chemical properties of tungsten carbide lead to significant tool wear and therefore the impossibility of machining the work pieces in an economical way. One approach to enlarge the tool life is to affect the contact zone between tool and work piece by the use of special cutting fluids. This publication emphasizes on the most recent investigations and results in direct machining of nano-grained tungsten carbide with mono crystal diamonds under the influence of various kinds of cutting fluids. Therefore basic ruling experiments on binderless nano grained tungsten carbide were performed, where the tool performed a linear movement with a steadily increasing depth of cut. As the ductile cutting mechanism is a prerequisite for the optical manufacturing of tungsten carbide these experiments serve the purpose for establish the influence of different cutting fluid characteristics on the cutting performance of mono crystal diamonds. Eventually it is shown that by adjusting the coolant fluid it is possible to significantly shift the transition point from ductile to brittle removal to larger depths of cut eventually enabling a SPDT of binderless tungsten carbide molds.

Observing exoplanet populations with high-precision astrometry

NASA Astrophysics Data System (ADS)

Sahlmann, Johannes

2012-06-01

This thesis deals with the application of the astrometry technique, consisting in measuring the position of a star in the plane of the sky, for the discovery and characterisation of extra-solar planets. It is feasible only with a very high measurement precision, which motivates the use of space observatories, the development of new ground-based astronomical instrumentation and of innovative data analysis methods: The study of Sun-like stars with substellar companions using CORALIE radial velocities and HIPPARCOS astrometry leads to the determination of the frequency of close brown dwarf companions and to the discovery of a dividing line between massive planets and brown dwarf companions; An observation campaign employing optical imaging with a very large telescope demonstrates sufficient astrometric precision to detect planets around ultra-cool dwarf stars and the first results of the survey are presented; Finally, the design and initial astrometric performance of PRIMA, ! a new dual-feed near-infrared interferometric observing facility for relative astrometry is presented.

Audio-based performance evaluation of squash players

PubMed Central

Hajdú-Szücs, Katalin; Fenyvesi, Nóra; Vattay, Gábor

2018-01-01

In competitive sports it is often very hard to quantify the performance. A player to score or overtake may depend on only millesimal of seconds or millimeters. In racquet sports like tennis, table tennis and squash many events will occur in a short time duration, whose recording and analysis can help reveal the differences in performance. In this paper we show that it is possible to architect a framework that utilizes the characteristic sound patterns to precisely classify the types of and localize the positions of these events. From these basic information the shot types and the ball speed along the trajectories can be estimated. Comparing these estimates with the optimal speed and target the precision of the shot can be defined. The detailed shot statistics and precision information significantly enriches and improves data available today. Feeding them back to the players and the coaches facilitates to describe playing performance objectively and to improve strategy skills. The framework is implemented, its hardware and software components are installed and tested in a squash court. PMID:29579067

Electromagnetic Pumps for Conductive-Propellant Feed Systems

NASA Technical Reports Server (NTRS)

Markusic, T. E.; Polzin, K. A.

2005-01-01

There has been a recent, renewed interest in high-power electric thrusters for application in nuclear-electric propulsion systems. Two of the most promising thrusters utilize liquid metal propellants: the lithium-fed magnetoplasmadynamic thruster and the bismuth-fed Hall thruster. An important element of part of the maturation of these thrusters will be the development of compact, reliable conductive-propellant feed system components. In the present paper we provide design considerations and experimental calibration data for electromagnetic (EM) pumps. The role of an electromagnetic pump in a liquid metal feed system is to establish a pressure gradient between the propellant reservoir and the thruster - to establish the requisite mass flow rate. While EM pumps have previously been used to a limited extent in nuclear reactor cooling loops, they have never been implemented in electric propulsion (EP) systems. The potential benefit of using EM pumps for EP are reliability (no moving parts) and the ability to precisely meter the propellant flow rate. We have constructed and tested EM pumps that use gallium, lithium, and bismuth propellants. Design details, test results (pressure developed versus current), and material compatibility issues are reported. It is concluded that EM pumps are a viable technology for application in both laboratory and flight EP conductive-propellant feed systems.

Low-frequency signals produced by Northeast Atlantic killer whales (Orcinus orca).

PubMed

Samarra, Filipa I P; Deecke, Volker B; Miller, Patrick J O

2016-03-01

Killer whale acoustic behavior has been extensively investigated; however, most studies have focused on pulsed calls and whistles. This study reports the production of low-frequency signals by killer whales at frequencies below 300 Hz. Recordings were made in Iceland and Norway when killer whales were observed feeding on herring and no other marine mammal species were nearby. Low-frequency sounds were identified in Iceland and ranged in duration between 0.14 and 2.77 s and in frequency between 50 and 270 Hz, well below the previously reported lower limit for killer whale tonal sounds of 500 Hz. Low-frequency sounds appeared to be produced close in time to tail slaps, which are indicative of feeding attempts, suggesting that these sounds may be related to a feeding context. However, their precise function is unknown, and they could be the by-product of a non-vocal behavior rather than a vocal signal deliberately produced by the whales. Although killer whales in Norway exhibit similar feeding behavior, this sound has not been detected in recordings from Norway to date. This study suggests that, like other delphinids, killer whales produce low-frequency sounds, but further studies will be required to understand whether similar sounds exist in other killer whale populations.

Dynamic balance of excitation and inhibition rapidly modulates spike probability and precision in feed-forward hippocampal circuits

PubMed Central

Wahlstrom-Helgren, Sarah

2016-01-01

Feed-forward inhibitory (FFI) circuits are important for many information-processing functions. FFI circuit operations critically depend on the balance and timing between the excitatory and inhibitory components, which undergo rapid dynamic changes during neural activity due to short-term plasticity (STP) of both components. How dynamic changes in excitation/inhibition (E/I) balance during spike trains influence FFI circuit operations remains poorly understood. In the current study we examined the role of STP in the FFI circuit functions in the mouse hippocampus. Using a coincidence detection paradigm with simultaneous activation of two Schaffer collateral inputs, we found that the spiking probability in the target CA1 neuron was increased while spike precision concomitantly decreased during high-frequency bursts compared with a single spike. Blocking inhibitory synaptic transmission revealed that dynamics of inhibition predominately modulates the spike precision but not the changes in spiking probability, whereas the latter is modulated by the dynamics of excitation. Further analyses combining whole cell recordings and simulations of the FFI circuit suggested that dynamics of the inhibitory circuit component may influence spiking behavior during bursts by broadening the width of excitatory postsynaptic responses and that the strength of this modulation depends on the basal E/I ratio. We verified these predictions using a mouse model of fragile X syndrome, which has an elevated E/I ratio, and found a strongly reduced modulation of postsynaptic response width during bursts. Our results suggest that changes in the dynamics of excitatory and inhibitory circuit components due to STP play important yet distinct roles in modulating the properties of FFI circuits. PMID:27605532

Sheep numbers required for dry matter digestibility evaluations when fed fresh perennial ryegrass or forage rape.

PubMed

Sun, Xuezhao; Krijgsman, Linda; Waghorn, Garry C; Kjestrup, Holly; Koolaard, John; Pacheco, David

2017-03-01

Research trials with fresh forages often require accurate and precise measurement of digestibility and variation in digestion between individuals, and the duration of measurement periods needs to be established to ensure reliable data are obtained. The variation is likely to be greater when freshly harvested feeds are given, such as perennial ryegrass ( Lolium perenne L.) and forage rape ( Brassica napus L.), because the nutrient composition changes over time and in response to weather conditions. Daily feed intake and faeces output data from a digestibility trial with these forages were used to calculate the effects of differing lengths of the measurement period and differing numbers of sheep, on the precision of digestibility, with a view towards development of a protocol. Sixteen lambs aged 8 months and weighing 33 kg at the commencement of the trial were fed either perennial ryegrass or forage rape (8/treatment group) over 2 periods with 35 d between measurements. They had been acclimatised to the diets, having grazed them for 42 d prior to 11 days of indoor measurements. The sheep numbers required for a digestibility trial with different combinations of acclimatisation and measurement period lengths were subsequently calculated for 3 levels of imposed precision upon the estimate of mean dry matter (DM) digestibility. It is recommended that if the standard error of the mean for digestibility is equal to or higher than 5 g/kg DM, and if sheep are already used to a fresh perennial ryegrass or forage rape diet, then a minimum of 6 animals are needed and 4 acclimatisation days being fed individually in metabolic crates followed by 7 days of measurement.

Feeding of the megamouth shark (Pisces: Lamniformes: Megachasmidae) predicted by its hyoid arch: a biomechanical approach.

PubMed

Tomita, Taketeru; Sato, Keiichi; Suda, Kenta; Kawauchi, Junro; Nakaya, Kazuhiro

2011-05-01

Studies of the megamouth shark, one of three planktivorous sharks, can provide information about their evolutionary history. Megamouth shark feeding has never been observed in life animals, but two alternative hypotheses on biomechanics suggest either feeding, i.e., ram feeding or suction feeding. In this study, the second moment of area of the ceratohyal cartilages, which is an indicator of the flexural stiffness of the cartilages, is calculated for 21 species of ram- and suction-feeding sharks using computed tomography. The results indicate that suction-feeding sharks have ceratohyal cartilages with a larger second moment of area than ram-feeding sharks. The result also indicates that the ram-suction index, which is an indicator of relative contribution of ram and suction behavior, is also correlated with the second moment of area of the ceratohyal. Considering that large bending stresses are expected to be applied to the ceratohyal cartilage during suction, the larger second moment of area of the ceratohyal of suction-feeding sharks can be interpreted as an adaptation for suction feeding. Based on the small second moment of area of the ceratohyal cartilage of the megamouth shark, the feeding mode of the megamouth shark is considered to be ram feeding, similar to the planktivorous basking shark. From these results, an evolutionary scenario of feeding mechanics of three species of planktivorous sharks can be suggested. In this scenario, the planktivorous whale shark evolved ram feeding from a benthic suction-feeding ancestor. Ram feeding in the planktivorous megamouth shark and the basking shark evolved from ram feeding swimming-type ancestors and that both developed their unique filtering system to capture small-sized prey. Copyright © 2011 Wiley-Liss, Inc.

Porosity of spacer-filled channels in spiral-wound membrane systems: Quantification methods and impact on hydraulic characterization.

PubMed

Siddiqui, A; Lehmann, S; Haaksman, V; Ogier, J; Schellenberg, C; van Loosdrecht, M C M; Kruithof, J C; Vrouwenvelder, J S

2017-08-01

The porosity of spacer-filled feed channels influences the hydrodynamics of spiral-wound membrane systems and impacts the overall performance of the system. Therefore, an exact measurement and a detailed understanding of the impact of the feed channel porosity is required to understand and improve the hydrodynamics of spiral-wound membrane systems applied for desalination and wastewater reuse. The objectives of this study were to assess the accuracy of porosity measurement techniques for feed spacers differing in geometry and thickness and the consequences of using an inaccurate method on hydrodynamic predictions, which may affect permeate production. Six techniques were applied to measure the porosity namely, three volumetric techniques based on spacer strand count together with a cuboidal (SC), cylindrical (VCC) and ellipsoidal volume calculation (VCE) and three independent techniques based on volume displacement (VD), weight and density (WD) and computed tomography (CT) scanning. The CT method was introduced as an alternative for the other five already existing and applied methods in practice. Six feed spacers used for the porosity measurement differed in filament thickness, angle between the filaments and mesh-size. The results of the studies showed differences between the porosities, measured by the six methods. The results of the microscopic techniques SC, VCC and VCE deviated significantly from measurements by VD, WD and CT, which showed similar porosity values for all spacer types. Depending on the maximum deviation of the porosity measurement techniques from -6% to +6%, (i) the linear velocity deviations were -5.6% and +6.4% respectively and (ii) the pressure drop deviations were -31% and +43% respectively, illustrating the importance of an accurate porosity measurement. Because of the accuracy and standard deviation, the VD and WD method should be applied for the porosity determination of spacer-filled channels, while the CT method is recommended for numerical modelling purposes. The porosity has a linear relationship with the flow velocity and a superlinear effect on the pressure drop. Accurate porosity data are essential to evaluate feed spacer performance in spiral-wound membrane systems. Porosity of spacer-filled feed channels has a strong impact on membrane performance and biofouling impact. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Variation in the emission rate of sounds in a captive group of false killer whales Pseudorca crassidens during feedings: possible food anticipatory vocal activity?

NASA Astrophysics Data System (ADS)

Platto, Sara; Wang, Ding; Wang, Kexiong

2016-11-01

This study examines whether a group of captive false killer whales ( Pseudorca crassidens ) showed variations in the vocal rate around feeding times. The high level of motivation to express appetitive behaviors in captive animals may lead them to respond with changes of the behavioral activities during the time prior to food deliveries which are referred to as food anticipatory activity. False killer whales at Qingdao Polar Ocean World (Qingdao, China) showed significant variations of the rates of both the total sounds and sound classes (whistles, clicks, and burst pulses) around feedings. Precisely, from the Transition interval that recorded the lowest vocalization rate (3.40 s/m/d), the whales increased their acoustic emissions upon trainers' arrival (13.08 s/m/d). The high rate was maintained or intensified throughout the food delivery (25.12 s/m/d), and then reduced immediately after the animals were fed (9.91 s/m/d). These changes in the false killer whales sound production rates around feeding times supports the hypothesis of the presence of a food anticipatory vocal activity. Although sound rates may not give detailed information regarding referential aspects of the animal communication it might still shed light about the arousal levels of the individuals during different social or environmental conditions. Further experiments should be performed to assess if variations of the time of feeding routines may affect the vocal activity of cetaceans in captivity as well as their welfare.

The effect of starvation and re-feeding on mitochondrial potential in the midgut of Neocaridina davidi (Crustacea, Malacostraca)

PubMed Central

Włodarczyk, Agnieszka; Sonakowska, Lidia; Kamińska, Karolina; Marchewka, Angelika; Wilczek, Grażyna; Wilczek, Piotr; Student, Sebastian; Rost-Roszkowska, Magdalena

2017-01-01

The midgut in the freshwater shrimp Neocaridina davidi (previously named N. heteropoda) (Crustacea, Malacostraca) is composed of a tube-shaped intestine and a large hepatopancreas that is formed by numerous blind-ended tubules. The precise structure and ultrastructure of these regions were presented in our previous papers, while here we focused on the ultrastructural changes that occurred in the midgut epithelial cells (D-cells in the intestine, B- and F- cells in the hepatopancreas) after long-term starvation and re-feeding. We used transmission electron microscopy, light and confocal microscopes and flow cytometry to describe all of the changes that occurred due to the stressor with special emphasis on mitochondrial alterations. A quantitative assessment of cells with depolarized mitochondria helped us to establish whether there is a relationship between starvation, re-feeding and the inactivation/activation of mitochondria. The results of our studies showed that in the freshwater shrimp N. davidi that were analyzed, long-term starvation activates the degeneration of epithelial cells at the ultrastructural level and causes an increase of cells with depolarized (non-active) mitochondria. The process of re-feeding leads to the gradual regeneration of the cytoplasm of the midgut epithelial cells; however, these changes were observed at the ultrastructural level. Additionally, re-feeding causes the regeneration of mitochondrial ultrastructure. Therefore, we can state that the increase in the number of cells with polarized mitochondria occurs slowly and does not depend on ultrastructural alterations. PMID:28282457

The effect of starvation and re-feeding on mitochondrial potential in the midgut of Neocaridina davidi (Crustacea, Malacostraca).

PubMed

Włodarczyk, Agnieszka; Sonakowska, Lidia; Kamińska, Karolina; Marchewka, Angelika; Wilczek, Grażyna; Wilczek, Piotr; Student, Sebastian; Rost-Roszkowska, Magdalena

2017-01-01

The midgut in the freshwater shrimp Neocaridina davidi (previously named N. heteropoda) (Crustacea, Malacostraca) is composed of a tube-shaped intestine and a large hepatopancreas that is formed by numerous blind-ended tubules. The precise structure and ultrastructure of these regions were presented in our previous papers, while here we focused on the ultrastructural changes that occurred in the midgut epithelial cells (D-cells in the intestine, B- and F- cells in the hepatopancreas) after long-term starvation and re-feeding. We used transmission electron microscopy, light and confocal microscopes and flow cytometry to describe all of the changes that occurred due to the stressor with special emphasis on mitochondrial alterations. A quantitative assessment of cells with depolarized mitochondria helped us to establish whether there is a relationship between starvation, re-feeding and the inactivation/activation of mitochondria. The results of our studies showed that in the freshwater shrimp N. davidi that were analyzed, long-term starvation activates the degeneration of epithelial cells at the ultrastructural level and causes an increase of cells with depolarized (non-active) mitochondria. The process of re-feeding leads to the gradual regeneration of the cytoplasm of the midgut epithelial cells; however, these changes were observed at the ultrastructural level. Additionally, re-feeding causes the regeneration of mitochondrial ultrastructure. Therefore, we can state that the increase in the number of cells with polarized mitochondria occurs slowly and does not depend on ultrastructural alterations.

Spatial patterns of aflatoxin levels in relation to ear-feeding insect damage in pre-harvest corn.

PubMed

Ni, Xinzhi; Wilson, Jeffrey P; Buntin, G David; Guo, Baozhu; Krakowsky, Matthew D; Lee, R Dewey; Cottrell, Ted E; Scully, Brian T; Huffaker, Alisa; Schmelz, Eric A

2011-07-01

Key impediments to increased corn yield and quality in the southeastern US coastal plain region are damage by ear-feeding insects and aflatoxin contamination caused by infection of Aspergillus flavus. Key ear-feeding insects are corn earworm, Helicoverpa zea, fall armyworm, Spodoptera frugiperda, maize weevil, Sitophilus zeamais, and brown stink bug, Euschistus servus. In 2006 and 2007, aflatoxin contamination and insect damage were sampled before harvest in three 0.4-hectare corn fields using a grid sampling method. The feeding damage by each of ear/kernel-feeding insects (i.e., corn earworm/fall armyworm damage on the silk/cob, and discoloration of corn kernels by stink bugs), and maize weevil population were assessed at each grid point with five ears. The spatial distribution pattern of aflatoxin contamination was also assessed using the corn samples collected at each sampling point. Aflatoxin level was correlated to the number of maize weevils and stink bug-discolored kernels, but not closely correlated to either husk coverage or corn earworm damage. Contour maps of the maize weevil populations, stink bug-damaged kernels, and aflatoxin levels exhibited an aggregated distribution pattern with a strong edge effect on all three parameters. The separation of silk- and cob-feeding insects from kernel-feeding insects, as well as chewing (i.e., the corn earworm and maize weevil) and piercing-sucking insects (i.e., the stink bugs) and their damage in relation to aflatoxin accumulation is economically important. Both theoretic and applied ramifications of this study were discussed by proposing a hypothesis on the underlying mechanisms of the aggregated distribution patterns and strong edge effect of insect damage and aflatoxin contamination, and by discussing possible management tactics for aflatoxin reduction by proper management of kernel-feeding insects. Future directions on basic and applied research related to aflatoxin contamination are also discussed.

Spatial Patterns of Aflatoxin Levels in Relation to Ear-Feeding Insect Damage in Pre-Harvest Corn

PubMed Central

Ni, Xinzhi; Wilson, Jeffrey P.; Buntin, G. David; Guo, Baozhu; Krakowsky, Matthew D.; Lee, R. Dewey; Cottrell, Ted E.; Scully, Brian T.; Huffaker, Alisa; Schmelz, Eric A.

2011-01-01

Key impediments to increased corn yield and quality in the southeastern US coastal plain region are damage by ear-feeding insects and aflatoxin contamination caused by infection of Aspergillus flavus. Key ear-feeding insects are corn earworm, Helicoverpa zea, fall armyworm, Spodoptera frugiperda, maize weevil, Sitophilus zeamais, and brown stink bug, Euschistus servus. In 2006 and 2007, aflatoxin contamination and insect damage were sampled before harvest in three 0.4-hectare corn fields using a grid sampling method. The feeding damage by each of ear/kernel-feeding insects (i.e., corn earworm/fall armyworm damage on the silk/cob, and discoloration of corn kernels by stink bugs), and maize weevil population were assessed at each grid point with five ears. The spatial distribution pattern of aflatoxin contamination was also assessed using the corn samples collected at each sampling point. Aflatoxin level was correlated to the number of maize weevils and stink bug-discolored kernels, but not closely correlated to either husk coverage or corn earworm damage. Contour maps of the maize weevil populations, stink bug-damaged kernels, and aflatoxin levels exhibited an aggregated distribution pattern with a strong edge effect on all three parameters. The separation of silk- and cob-feeding insects from kernel-feeding insects, as well as chewing (i.e., the corn earworm and maize weevil) and piercing-sucking insects (i.e., the stink bugs) and their damage in relation to aflatoxin accumulation is economically important. Both theoretic and applied ramifications of this study were discussed by proposing a hypothesis on the underlying mechanisms of the aggregated distribution patterns and strong edge effect of insect damage and aflatoxin contamination, and by discussing possible management tactics for aflatoxin reduction by proper management of kernel-feeding insects. Future directions on basic and applied research related to aflatoxin contamination are also discussed. PMID:22069748

A new microscope optics for laser dark-field illumination applied to high precision two dimensional measurement of specimen displacement.

PubMed

Noda, Naoki; Kamimura, Shinji

2008-02-01

With conventional light microscopy, precision in the measurement of the displacement of a specimen depends on the signal-to-noise ratio when we measure the light intensity of magnified images. This implies that, for the improvement of precision, getting brighter images and reducing background light noise are both inevitably required. For this purpose, we developed a new optics for laser dark-field illumination. For the microscopy, we used a laser beam and a pair of axicons (conical lenses) to get an optimal condition for dark-field observations. The optics was applied to measuring two dimensional microbead displacements with subnanometer precision. The bandwidth of our detection system overall was 10 kHz. Over most of this bandwidth, the observed noise level was as small as 0.1 nm/radicalHz.

An experimental study of nettle feeding in captive gorillas.

PubMed

Tennie, Claudio; Hedwig, Daniela; Call, Josep; Tomasello, Michael

2008-06-01

Mountain gorillas (Gorilla beringei beringei) in Karisoke, Rwanda, feed on the stinging nettle Laportea alatipes by means of elaborate processing skills. Byrne [e.g. Philosophical Transactions of the Royal Society of London, Series B, Biological Sciences 358:529-536, 2003] has claimed that individuals acquire these skills by means of the so-called program-level imitation, in which the overall sequence of problem-solving steps (not the precise actions) is reproduced. In this study we present western lowland gorillas (Gorilla gorilla gorilla) with highly similar nettles. Twelve gorillas in three different groups (including also one nettle-naïve gorilla) used the same program-level technique as wild mountain gorillas (with differences mainly on the action level). Chimpanzees, orangutans, and bonobos did not show these program-level patterns, nor did the gorillas when presented with a plant similar in structural design but lacking stinging defenses. We conclude that although certain aspects (i.e. single actions) of this complex skill may be owing to social learning, at the program level gorilla nettle feeding derives mostly from genetic predispositions and individual learning of plant affordances. Copyright 2008 Wiley-Liss, Inc.

Optimizing the way kinematical feed chains with great distance between slides are chosen for CNC machine tools

NASA Astrophysics Data System (ADS)

Lucian, P.; Gheorghe, S.

2017-08-01

This paper presents a new method, based on FRISCO formula, for optimizing the choice of the best control system for kinematical feed chains with great distance between slides used in computer numerical controlled machine tools. Such machines are usually, but not limited to, used for machining large and complex parts (mostly in the aviation industry) or complex casting molds. For such machine tools the kinematic feed chains are arranged in a dual-parallel drive structure that allows the mobile element to be moved by the two kinematical branches and their related control systems. Such an arrangement allows for high speed and high rigidity (a critical requirement for precision machining) during the machining process. A significant issue for such an arrangement it’s the ability of the two parallel control systems to follow the same trajectory accurately in order to address this issue it is necessary to achieve synchronous motion control for the two kinematical branches ensuring that the correct perpendicular position it’s kept by the mobile element during its motion on the two slides.

Prandiology of Drosophila and the CAFE assay

PubMed Central

Ja, William W.; Carvalho, Gil B.; Mak, Elizabeth M.; de la Rosa, Noelle N.; Fang, Annie Y.; Liong, Jonathan C.; Brummel, Ted; Benzer, Seymour

2007-01-01

Studies of feeding behavior in genetically tractable invertebrate model systems have been limited by the lack of proper methodology. We introduce the Capillary Feeder (CAFE), a method allowing precise, real-time measurement of ingestion by individual or grouped fruit flies on the scale of minutes to days. Using this technique, we conducted the first quantitative analysis of prandial behavior in Drosophila melanogaster. Our results allow the dissection of feeding into discrete bouts of ingestion, defining two separate parameters, meal volume and frequency, that can be uncoupled and thus are likely to be independently regulated. In addition, our long-term measurements show that flies can ingest as much as 1.7× their body mass over 24 h. Besides the study of appetite, the CAFE can be used to monitor oral drug delivery. As an illustration, we used the CAFE to test the effects of dietary supplementation with two compounds, paraquat and ethanol, on food ingestion and preference. Paraquat, a prooxidant widely used in stress tests, had a strong anorexigenic effect. In contrast, in a feeding preference assay, ethanol-laced food, but not ethanol by itself, acted as an attractant. PMID:17494737

Suction is kid's play: extremely fast suction in newborn seahorses.

PubMed

Van Wassenbergh, Sam; Roos, Gert; Genbrugge, Annelies; Leysen, Heleen; Aerts, Peter; Adriaens, Dominique; Herrel, Anthony

2009-04-23

Ongoing anatomical development typically results in a gradual maturation of the feeding movements from larval to adult fishes. Adult seahorses are known to capture prey by rotating their long-snouted head extremely quickly towards prey, followed by powerful suction. This type of suction is powered by elastic recoil and requires very precise coordination of the movements of the associated feeding structures, making it an all-or-none phenomenon. Here, we show that newborn Hippocampus reidi are able to successfully feed using an extremely rapid and powerful snout rotation combined with a high-volume suction, surpassing that observed in adult seahorses. An inverse dynamic analysis shows that an elastic recoil mechanism is also used to power head rotation in newborn H. reidi. This illustrates how extreme levels of performance in highly complex musculoskeletal systems can be present at birth given a delayed birth and rapid development of functionally important structures. The fact that the head skeleton of newborn seahorses is still largely cartilaginous may not be problematic because the hydrodynamic stress on the rotating snout appeared considerably lower than in adult syngnathids.

Suction is kid's play: extremely fast suction in newborn seahorses

PubMed Central

Van Wassenbergh, Sam; Roos, Gert; Genbrugge, Annelies; Leysen, Heleen; Aerts, Peter; Adriaens, Dominique; Herrel, Anthony

2009-01-01

Ongoing anatomical development typically results in a gradual maturation of the feeding movements from larval to adult fishes. Adult seahorses are known to capture prey by rotating their long-snouted head extremely quickly towards prey, followed by powerful suction. This type of suction is powered by elastic recoil and requires very precise coordination of the movements of the associated feeding structures, making it an all-or-none phenomenon. Here, we show that newborn Hippocampus reidi are able to successfully feed using an extremely rapid and powerful snout rotation combined with a high-volume suction, surpassing that observed in adult seahorses. An inverse dynamic analysis shows that an elastic recoil mechanism is also used to power head rotation in newborn H. reidi. This illustrates how extreme levels of performance in highly complex musculoskeletal systems can be present at birth given a delayed birth and rapid development of functionally important structures. The fact that the head skeleton of newborn seahorses is still largely cartilaginous may not be problematic because the hydrodynamic stress on the rotating snout appeared considerably lower than in adult syngnathids. PMID:19324657

KSC-08pd0078

NASA Image and Video Library

2008-01-23

KENNEDY SPACE CENTER, FLA. -- Quality inspectors with NASA and Lockheed Martin examine a red-line drawing of foam placement on space shuttle Atlantis's external tank (in front of them) to verify the foam insulation that was reapplied. The foam covers the feed-through engine cut-off, or ECO, sensor connector. The foam was removed to enable engineers to remove and replace the ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The repair work was done on Atlantis while the shuttle has been on Launch Pad 39A at NASA's Kennedy Space Center. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Cory Husten

KSC-08pd0033

NASA Image and Video Library

2008-01-11

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A, Lockheed Martin engineer Ray Clark splices wires between space shuttle Atlantis' external tank and the engine cutoff, or ECO, sensor system. The replacement feed-through connector in the ECO sensor system will be installed later. Some of the tank's ECO sensors gave failed readings during propellant tanking for Atlantis' STS-122 mission launch attempts on Dec. 6 and Dec. 9. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The feed-through connector passes the wires from the inside of the tank to the outside. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. No problems with the ECO sensors themselves have been found. NASA's Space Shuttle Program has proposed a target launch date of Feb. 7 for the STS-122 mission. That proposed launch date remains under evaluation pending coordination with all partners in the International Space Station Program. Photo credit: NASA/George Shelton

KSC-08pd0077

NASA Image and Video Library

2008-01-23

KENNEDY SPACE CENTER, FLA. -- Quality inspectors with NASA and Lockheed Martin examine a red-line drawing of foam placement on space shuttle Atlantis's external tank (in front of them) to verify the foam insulation that was reapplied. The foam covers the feed-through engine cut-off, or ECO, sensor connector. The foam was removed to enable engineers to remove and replace the ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The repair work was done on Atlantis while the shuttle has been on Launch Pad 39A at NASA's Kennedy Space Center. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Cory Husten

KSC-08pd0076

NASA Image and Video Library

2008-01-23

KENNEDY SPACE CENTER, FLA. -- The white foam insulation freshly reapplied to space shuttle Atlantis's external tank completes the work to remove and replace the feed-through connector on the engine cut-off, or ECO, sensor connector. The repair work was done on Atlantis while the shuttle has been on Launch Pad 39A at NASA's Kennedy Space Center. The foam was removed to enable engineers to remove and replace the ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The repair work was done on Atlantis while the shuttle has been on Launch Pad 39A at NASA's Kennedy Space Center. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Cory Husten

KSC-08pd0035

NASA Image and Video Library

2008-01-11

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A, Lockheed Martin engineer Ray Clark splices wires between space shuttle Atlantis' external tank and the engine cutoff, or ECO, sensor system. The replacement feed-through connector in the ECO sensor system will be installed later. Some of the tank's ECO sensors gave failed readings during propellant tanking for Atlantis' STS-122 mission launch attempts on Dec. 6 and Dec. 9. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The feed-through connector passes the wires from the inside of the tank to the outside. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. No problems with the ECO sensors themselves have been found. NASA's Space Shuttle Program has proposed a target launch date of Feb. 7 for the STS-122 mission. That proposed launch date remains under evaluation pending coordination with all partners in the International Space Station Program. Photo credit: NASA/George Shelton

KSC-08pd0080

NASA Image and Video Library

2008-01-23

KENNEDY SPACE CENTER, FLA. -- Quality inspectors with NASA and Lockheed Martin examine a red-line drawing of foam placement on space shuttle Atlantis's external tank (in front of them) to verify the foam insulation that was reapplied. The foam covers the feed-through engine cut-off, or ECO, sensor connector. The foam was removed to enable engineers to remove and replace the ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The repair work was done on Atlantis while the shuttle has been on Launch Pad 39A at NASA's Kennedy Space Center. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Cory Husten

KSC-08pd0034

NASA Image and Video Library

2008-01-11

KENNEDY SPACE CENTER, FLA. -- On Launch Pad 39A, Lockheed Martin engineer Ray Clark splices wires between space shuttle Atlantis' external tank and the engine cutoff, or ECO, sensor system. The replacement feed-through connector in the ECO sensor system will be installed later. Some of the tank's ECO sensors gave failed readings during propellant tanking for Atlantis' STS-122 mission launch attempts on Dec. 6 and Dec. 9. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The feed-through connector passes the wires from the inside of the tank to the outside. The pins in the replacement connector have been precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. No problems with the ECO sensors themselves have been found. NASA's Space Shuttle Program has proposed a target launch date of Feb. 7 for the STS-122 mission. That proposed launch date remains under evaluation pending coordination with all partners in the International Space Station Program. Photo credit: NASA/George Shelton

KSC-08pd0075

NASA Image and Video Library

2008-01-23

KENNEDY SPACE CENTER, FLA. -- The white foam insulation freshly reapplied to space shuttle Atlantis's external tank completes the work to remove and replace the feed-through connector on the engine cut-off, or ECO, sensor connector. The repair work was done on Atlantis while the shuttle has been on Launch Pad 39A at NASA's Kennedy Space Center. The foam was removed to enable engineers to remove and replace the ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The repair work was done on Atlantis while the shuttle has been on Launch Pad 39A at NASA's Kennedy Space Center. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Cory Husten

KSC-08pd0079

NASA Image and Video Library

2008-01-23

KENNEDY SPACE CENTER, FLA. -- Quality inspectors with NASA and Lockheed Martin examine a red-line drawing of foam placement on space shuttle Atlantis's external tank (in front of them) to verify the foam insulation that was reapplied. The foam covers the feed-through engine cut-off, or ECO, sensor connector. The foam was removed to enable engineers to remove and replace the ECO sensor connector on the tank. The feed-through connector passes the wires from the inside of the tank to the outside. Results of a tanking test on Dec. 18 pointed to an open circuit in the feed-through connector wiring, which is located at the base of the tank. The pins in the replacement connector were precisely soldered to create a connection that allows sensors inside the tank to send signals to the computers onboard Atlantis. The repair work was done on Atlantis while the shuttle has been on Launch Pad 39A at NASA's Kennedy Space Center. The launch date for the shuttle's STS-122 mission has now been targeted for Feb. 7. Photo credit: NASA/Cory Husten

Impact on environment, ecosystem, diversity and health from culturing and using GMOs as feed and food.

PubMed

Tsatsakis, Aristidis M; Nawaz, Muhammad Amjad; Tutelyan, Victor A; Golokhvast, Kirill S; Kalantzi, Olga-Ioanna; Chung, Duck Hwa; Kang, Sung Jo; Coleman, Michael D; Tyshko, Nadia; Yang, Seung Hwan; Chung, Gyuhwa

2017-09-01

Modern agriculture provides the potential for sustainable feeding of the world's increasing population. Up to the present moment, genetically modified (GM) products have enabled increased yields and reduced pesticide usage. Nevertheless, GM products are controversial amongst policy makers, scientists and the consumers, regarding their possible environmental, ecological, and health risks. Scientific-and-political debates can even influence legislation and prospective risk assessment procedure. Currently, the scientifically-assessed direct hazardous impacts of GM food and feed on fauna and flora are conflicting; indeed, a review of literature available data provides some evidence of GM environmental and health risks. Although the consequences of gene flow and risks to biodiversity are debatable. Risks to the environment and ecosystems can exist, such as the evolution of weed herbicide resistance during GM cultivation. A matter of high importance is to provide precise knowledge and adequate current information to regulatory agencies, governments, policy makers, researchers, and commercial GMO-releasing companies to enable them to thoroughly investigate the possible risks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Certain applied electrical signals during EPG cause negative effects on stylet probing behaviors by adult Lygus lineolaris (Hemiptera: Miridae)

USDA-ARS?s Scientific Manuscript database

This study is the first to fully evaluate whether electrical signals applied to insects during electropenetrography (EPG; also called electrical penetration graph) affect insect behavior. During EPG, electrical signals are applied to plants, and thus to the gold-wire-tethered insects feeding on elec...

Metatranscriptomic Profiling Reveals Linkages between the Active Rumen Microbiome and Feed Efficiency in Beef Cattle

PubMed Central

Li, Fuyong

2017-01-01

ABSTRACT Exploring compositional and functional characteristics of the rumen microbiome can improve the understanding of its role in rumen function and cattle feed efficiency. In this study, we applied metatranscriptomics to characterize the active rumen microbiomes of beef cattle with different feed efficiencies (efficient, n = 10; inefficient, n = 10) using total RNA sequencing. Active bacterial and archaeal compositions were estimated based on 16S rRNAs, and active microbial metabolic functions including carbohydrate-active enzymes (CAZymes) were assessed based on mRNAs from the same metatranscriptomic data sets. In total, six bacterial phyla (Proteobacteria, Firmicutes, Bacteroidetes, Spirochaetes, Cyanobacteria, and Synergistetes), eight bacterial families (Succinivibrionaceae, Prevotellaceae, Ruminococcaceae, Lachnospiraceae, Veillonellaceae, Spirochaetaceae, Dethiosulfovibrionaceae, and Mogibacteriaceae), four archaeal clades (Methanomassiliicoccales, Methanobrevibacter ruminantium, Methanobrevibacter gottschalkii, and Methanosphaera), 112 metabolic pathways, and 126 CAZymes were identified as core components of the active rumen microbiome. As determined by comparative analysis, three bacterial families (Lachnospiraceae, Lactobacillaceae, and Veillonellaceae) tended to be more abundant in low-feed-efficiency (inefficient) animals (P < 0.10), and one archaeal taxon (Methanomassiliicoccales) tended to be more abundant in high-feed-efficiency (efficient) cattle (P < 0.10). Meanwhile, 32 microbial metabolic pathways and 12 CAZymes were differentially abundant (linear discriminant analysis score of >2 with a P value of <0.05) between two groups. Among them, 30 metabolic pathways and 11 CAZymes were more abundant in the rumen of inefficient cattle, while 2 metabolic pathways and 1 CAZyme were more abundant in efficient animals. These findings suggest that the rumen microbiomes of inefficient cattle have more diverse activities than those of efficient cattle, which may be related to the host feed efficiency variation. IMPORTANCE This study applied total RNA-based metatranscriptomics and showed the linkage between the active rumen microbiome and feed efficiency (residual feed intake) in beef cattle. The data generated from the current study provide fundamental information on active rumen microbiome at both compositional and functional levels, which serve as a foundation to study rumen function and its role in cattle feed efficiency. The findings that the active rumen microbiome may contribute to variations in feed efficiency of beef cattle highlight the possibility of enhancing nutrient utilization and improve cattle feed efficiency through modification of rumen microbial functions. PMID:28235871

A Framework to Evaluate Wildlife Feeding in Research, Wildlife Management, Tourism and Recreation

PubMed Central

Dubois, Sara; Fraser, David

2013-01-01

Simple Summary Human feeding of wildlife is a world-wide phenomenon with very diverse effects on conservation, animal welfare and public safety. From a review of the motivations, types and consequences of wildlife feeding, an evaluative framework is presented to assist policy-makers, educators and managers to make ethical- and biologically-based decisions about the appropriateness of feeding wildlife in the context of research, wildlife management, tourism and recreation. Abstract Feeding of wildlife occurs in the context of research, wildlife management, tourism and in opportunistic ways. A review of examples shows that although feeding is often motivated by good intentions, it can lead to problems of public safety and conservation and be detrimental to the welfare of the animals. Examples from British Columbia illustrate the problems (nuisance animal activity, public safety risk) and consequences (culling, translocation) that often arise from uncontrolled feeding. Three features of wildlife feeding can be distinguished: the feasibility of control, the effects on conservation and the effects on animal welfare. An evaluative framework incorporating these three features was applied to examples of feeding from the literature. The cases of feeding for research and management purposes were generally found to be acceptable, while cases of feeding for tourism or opportunistic feeding were generally unacceptable. The framework should allow managers and policy-makers to distinguish acceptable from unacceptable forms of wildlife feeding as a basis for policy, public education and enforcement. Many harmful forms of wildlife feeding seem unlikely to change until they come to be seen as socially unacceptable. PMID:26479747

Intestinal digestibility of amino acids in rumen-undegraded protein estimated using a precision-fed cecectomized rooster bioassay: II. Distillers dried grains with solubles and fish meal.

PubMed

Boucher, S E; Calsamiglia, S; Parsons, C M; Stein, H H; Stern, M D; Erickson, P S; Utterback, P L; Schwab, C G

2009-12-01

The objectives of this experiment were to measure intestinal digestibility of AA in the rumen-undegraded protein fraction (RUP-AA) of distillers dried grains with solubles (DDGS) and fish meal (FM) samples and to determine whether these feeds contain a constant protein fraction that is undegradable in the rumen and indigestible in the small intestine, as assumed in the French Institut National de la Recherche Agronomique (Paris, France) and Scandinavian AAT-PBV (AAT = AA absorbed from small intestine; PBV = protein balance in the rumen) models. Five sources of DDGS and 5 sources of FM were obtained from Feed Analysis Consortium, Inc. (Champaign, IL). To obtain the rumen-undegradable protein fraction, samples were ruminally incubated in situ for 16 h in 4 lactating cows, and the collected rumen-undegraded residues (RUR) were pooled by sample. Subsamples of the intact feeds and RUR were crop-intubated to 4 cecectomized roosters, and total excreta were collected for 48 h. Intact feeds, RUR, and excreta were analyzed for AA. Basal endogenous AA loss estimates were obtained from fasted birds and were used to calculate standardized digestibility of RUP-AA and AA in the intact feeds. Indigestibility coefficients of the intact feeds were calculated as (100 - % standardized AA digestibility), and indigestibility of the RUR was calculated as [(100 - % ruminal degradation of AA) x (100 - % standardized RUP-AA digestibility)/100]. Results indicate that standardized digestibility of feed-AA differs from RUP-AA for DDGS samples but not for FM samples, and that standardized digestibility of individual AA differs within samples. For the DDGS samples, standardized feed-AA and RUP-AA digestibility values were most often lowest for His and Lys and highest for Met and Trp. For FM samples, standardized feed-AA and RUP-AA digestibility values were most often lowest for His and highest for Trp. Results also indicate that DDGS and most FM samples do not contain a constant protein fraction that is both undegradable in the rumen and indigestible in the small intestine. Indigestibility values of RUR were lower than in intact feeds, suggesting that the feed ingredients used in this experiment contain a protein fraction that is indigestible in the intestine but partly degradable in the rumen or digestible in the intestine after rumen incubation, or both.

POST-HIGH SCHOOL CURRICULUM FOR THE GRAIN, FEED, SEED AND FARM SUPPLY INDUSTRY.

ERIC Educational Resources Information Center

CLARK, RAYMOND M.; OLIVER, ALVIN E.

A COMMITTEE OF EDUCATION AND INDUSTRY REPRESENTATIVES RECOMMENDED 20 ESSENTIAL AND THREE SUBSTITUTE COURSES FOR A 2-YEAR POST-HIGH SCHOOL PROGRAM FOR TRAINING YOUNG MEN FOR THE NATIONAL GRAIN, FEED, SEED, AND FARM SUPPLY INDUSTRY. SOME ESSENTIAL COURSES WERE (1) SOIL SCIENCE I AND II, (2) CROP PRODUCTION, (3) APPLIED ANIMAL BIOCHEMISTRY, (4)…

21 CFR 589.2001 - Cattle materials prohibited in animal food or feed to prevent the transmission of bovine...

Code of Federal Regulations, 2012 CFR

2012-04-01

.... Bradley Ave., Champaign, IL 61821. Copies may be examined at the Center for Food Safety and Applied..., or metabolic conditions. (3) Mechanically separated beef means a finely comminuted meat food product... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Cattle materials prohibited in animal food or feed...

21 CFR 589.2001 - Cattle materials prohibited in animal food or feed to prevent the transmission of bovine...

Code of Federal Regulations, 2010 CFR

2010-04-01

.... Bradley Ave., Champaign, IL 61821. Copies may be examined at the Center for Food Safety and Applied..., or metabolic conditions. (3) Mechanically separated beef means a finely comminuted meat food product... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Cattle materials prohibited in animal food or feed...

21 CFR 589.2001 - Cattle materials prohibited in animal food or feed to prevent the transmission of bovine...

Code of Federal Regulations, 2013 CFR

2013-04-01

.... Bradley Ave., Champaign, IL 61821. Copies may be examined at the Center for Food Safety and Applied..., or metabolic conditions. (3) Mechanically separated beef means a finely comminuted meat food product... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Cattle materials prohibited in animal food or feed...

21 CFR 589.2001 - Cattle materials prohibited in animal food or feed to prevent the transmission of bovine...

Code of Federal Regulations, 2011 CFR

2011-04-01

.... Bradley Ave., Champaign, IL 61821. Copies may be examined at the Center for Food Safety and Applied..., or metabolic conditions. (3) Mechanically separated beef means a finely comminuted meat food product... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Cattle materials prohibited in animal food or feed...

21 CFR 589.2001 - Cattle materials prohibited in animal food or feed to prevent the transmission of bovine...

Code of Federal Regulations, 2014 CFR

2014-04-01

.... Bradley Ave., Champaign, IL 61821. Copies may be examined at the Center for Food Safety and Applied..., or metabolic conditions. (3) Mechanically separated beef means a finely comminuted meat food product... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Cattle materials prohibited in animal food or feed...

Effect of feed-related farm characteristics on relative values of genetic traits in dairy cows to reduce greenhouse gas emissions along the chain.

PubMed

Van Middelaar, C E; Berentsen, P B M; Dijkstra, J; Van Arendonk, J A M; De Boer, I J M

2015-07-01

Breeding has the potential to reduce greenhouse gas (GHG) emissions from dairy farming. Evaluating the effect of a 1-unit change (i.e., 1 genetic standard deviation improvement) in genetic traits on GHG emissions along the chain provides insight into the relative importance of genetic traits to reduce GHG emissions. Relative GHG values of genetic traits, however, might depend on feed-related farm characteristics. The objective of this study was to evaluate the effect of feed-related farm characteristics on GHG values by comparing the values of milk yield and longevity for an efficient farm and a less efficient farm. The less efficient farm did not apply precision feeding and had lower feed production per hectare than the efficient farm. Greenhouse gas values of milk yield and longevity were calculated by using a whole-farm model and 2 different optimization methods. Method 1 optimized farm management before and after a change in genetic trait by maximizing labor income; the effect on GHG emissions (i.e., from production of farm inputs up to the farm gate) was considered a side effect. Method 2 optimized farm management after a change in genetic trait by minimizing GHG emissions per kilogram of milk while maintaining labor income and milk production at least at the level before the change in trait; the effect on labor income was considered a side effect. Based on maximizing labor income (method 1), GHG values of milk yield and longevity were, respectively, 279 and 143kg of CO2 equivalents (CO2e)/unit change per cow per year on the less efficient farm, and 247 and 210kg of CO2e/unit change per cow per year on the efficient farm. Based on minimizing GHG emissions (method 2), GHG values of milk yield and longevity were, respectively, 538 and 563kg of CO2e/unit change per cow per year on the less efficient farm, and 453 and 441kg of CO2e/unit change per cow per year on the efficient farm. Sensitivity analysis showed that, for both methods, the absolute effect of a change in genetic trait depends on model inputs, including prices and emission factors. Substantial changes in relative importance between traits due to a change in model inputs occurred only in case of maximizing labor income. We concluded that assumptions regarding feed-related farm characteristics affect the absolute level of GHG values, as well as the relative importance of traits to reduce emissions when using a method based on maximizing labor income. This is because optimizing farm management based on maximizing labor income does not give any incentive for lowering GHG emissions. When using a method based on minimizing GHG emissions, feed-related farm characteristics affected the absolute level of the GHG values, but the relative importance of the traits scarcely changed: at each level of efficiency, milk yield and longevity were equally important. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Total Breast-Feeding Duration and Dental Caries in Healthy Urban Children.

PubMed

Wong, Peter D; Birken, Catherine S; Parkin, Patricia C; Venu, Isvarya; Chen, Yang; Schroth, Robert J; Maguire, Jonathon L

2017-04-01

To determine if there is an association between longer breast-feeding duration and dental caries in healthy urban children. We conducted a cross-sectional study of urban children aged 1 to 6 years recruited through The Applied Research Group for Kids (TARGet Kids!) practice-based research network between September 2011 and August 2013. The main outcome measure was parental report of dental caries. The adjusted predicted probability of dental caries was 7%, 8%, 11%, and 16% with total duration of breast-feeding duration of 12, 18, 24, and 36 months, respectively. In the adjusted logistic regression analyses, relative to breast-feeding 0 to 5 months, the odds of dental caries with total breast-feeding duration >24 months was 2.75 (95% confidence interval 1.61-4.72). Among healthy urban children, longer breast-feeding duration was associated with higher odds of dental caries. These findings support heightened awareness and enhanced anticipatory guidance for preventive dental care, particularly among children who breast-feed beyond 2 years of age. Copyright © 2016 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

Investigation of pharmaceuticals in processed animal by-products by liquid chromatography coupled to high-resolution mass spectrometry.

PubMed

Nácher-Mestre, Jaime; Ibáñez, María; Serrano, Roque; Boix, Clara; Bijlsma, Lubertus; Lunestad, Bjørn Tore; Hannisdal, Rita; Alm, Martin; Hernández, Félix; Berntssen, Marc H G

2016-07-01

There is an on-going trend for developing more sustainable salmon feed in which traditionally applied marine feed ingredients are replaced with alternatives. Processed animal products (PAPs) have been re-authorized as novel high quality protein ingredients in 2013. These PAPs may harbor undesirable substances such as pharmaceuticals and metabolites which are not previously associated with salmon farming, but might cause a potential risk for feed and food safety. To control these contaminants, an analytical strategy based on a generic extraction followed by ultra-high performance liquid chromatography coupled to high resolution mass spectrometry (UHPLC-HRMS) using quadrupole time-of-flight mass analyzer (QTOF MS) was applied for wide scope screening. Quality control samples, consisting of PAP commodities spiked at 0.02, 0.1 and 0.2 mg/kg with 150 analytes, were injected in every sample batch to verify the overall method performance. The methodology was applied to 19 commercially available PAP samples from six different types of matrices from the EU animal rendering industry. This strategy allows assessing possible emergent risk exposition of the salmon farming industry to 1005 undesirables, including pharmaceuticals, several dyes and relevant metabolites. Copyright © 2016 Elsevier Ltd. All rights reserved.

High-level production of L-threonine by recombinant Escherichia coli with combined feeding strategies

PubMed Central

Wang, Jian; Cheng, Li-Kun; Chen, Ning

2014-01-01

The process of L-threonine production using Escherichia coli TRFC was investigated, and the result showed that there was a large amount of acetic acid in the broth. The effects of acetic acid, which is a known inhibitory metabolite in E. coli cultivation, on L-threonine production by recombinant E. coli TRFC were evaluated, and the result indicated that the growth of E. coli TRFC and L-threonine formation were significantly inhibited in the presence of acetic acid. Two combined feeding strategies were applied to L-threonine fed-batch fermentation in order to investigate the effects of the feeding strategy on L-threonine fermentation. The results showed that using the combined feeding strategy of pseudo-exponential feeding and glucose-stat feeding resulted in high cell density (36.67 g L−1) and L-threonine production (124.57 g L−1) as well as low accumulation of by-products. This work provides a useful approach for large-scale production of L-threonine. PMID:26019535

Design and evaluation of a Stochastic Optimal Feed-forward and Feedback Technology (SOFFT) flight control architecture

NASA Technical Reports Server (NTRS)

Ostroff, Aaron J.; Proffitt, Melissa S.

1994-01-01

This paper describes the design and evaluation of a stochastic optimal feed-forward and feedback technology (SOFFT) control architecture with emphasis on the feed-forward controller design. The SOFFT approach allows the designer to independently design the feed-forward and feedback controllers to meet separate objectives and then integrate the two controllers. The feed-forward controller has been integrated with an existing high-angle-of-attack (high-alpha) feedback controller. The feed-forward controller includes a variable command model with parameters selected to satisfy level 1 flying qualities with a high-alpha adjustment to achieve desired agility guidelines, a nonlinear interpolation approach that scales entire matrices for approximation of the plant model, and equations for calculating feed-forward gains developed for perfect plant-model tracking. The SOFFT design was applied to a nonlinear batch simulation model of an F/A-18 aircraft modified for thrust vectoring. Simulation results show that agility guidelines are met and that the SOFFT controller filters undesired pilot-induced frequencies more effectively during a tracking task than a flight controller that has the same feedback control law but does not have the SOFFT feed-forward control.

Intestinal digestibility of amino acids in rumen undegradable protein estimated using a precision-fed cecectomized rooster bioassay: I. Soybean meal and SoyPlus.

PubMed

Boucher, S E; Calsamiglia, S; Parsons, C M; Stein, H H; Stern, M D; Erickson, P S; Utterback, P L; Schwab, C G

2009-09-01

The objectives of this experiment were to measure intestinal digestibility of AA in rumen undegradable protein (RUP-AA) in soybean meal (SBM) and expeller SBM (SoyPlus, West Central, Ralston, IA; SP) and to determine if these feeds contain a constant protein fraction that is undegradable in the rumen and indigestible in the small intestine, as assumed in the French Institut National de la Recherche Agronomique (Paris, France) and Scandinavian AAT-PBV (AAT = AA absorbed from small intestine; PBV = protein balance in the rumen) models. Three samples of SBM and 3 samples of SP were obtained from the Feed Analysis Consortium Inc. (Savoy, IL). To obtain the RUP fraction, samples were ruminally incubated in situ for 16 h in 4 lactating cows, and the collected rumen undegraded residues (RUR) were pooled by sample. Subsamples of the intact feeds and RUR were crop intubated to 4 cecectomized roosters, and total excreta were collected for 48 h. Intact feeds, RUR, and excreta were analyzed for AA. Basal endogenous AA loss estimates were obtained from fasted birds and were used to calculate standardized digestibility of AA in the intact feeds and RUP-AA. Indigestibility coefficients of the intact feeds were calculated as (100 - % standardized AA digestibility), and indigestibility of the RUR was calculated as [(100 - % ruminal degradation of AA) x [(100 - % standardized RUP-AA digestibility)]/100]. Results indicated that standardized digestibility of feed-AA was similar to standardized digestibility of RUP-AA for SBM and SP samples and that standardized digestibility of individual AA differed within samples. Standardized feed-AA and RUP-AA digestibility values were lowest for Lys and Cys and highest for Trp and Met. Results also indicated that SBM and SP did not contain a constant protein fraction that was both undegradable in the rumen and indigestible in the small intestine. Indigestibility values of RUR were lower than in intact feeds, suggesting that SBM and SP contain a protein fraction that is indigestible in the intestine but partly degradable in the rumen, digestible in the intestine after ruminal incubation, or both.

2005 Precision Strike Technology Symposium

DTIC Science & Technology

2005-10-20

Radars in  Production  Mission Computer  Software   Functionality to drive Mission System Requirements  Liquid  Cooling   Expanded  Cooling   Capability and Flow...Targeting Demonstration Using the APL Precision Target Locator Demonstrator, Mr. Ben Huguenin and Mr. Joe Schissler, Johns Hopkins University, Applied ...Forces October 18-20, 2005 Kossiakoff Conference Center The Johns Hopkins University/ Applied Physics Laboratory, Laurel, MD David K. Sanders

F-MAP: A Bayesian approach to infer the gene regulatory network using external hints

PubMed Central

Shahdoust, Maryam; Mahjub, Hossein; Sadeghi, Mehdi

2017-01-01

The Common topological features of related species gene regulatory networks suggest reconstruction of the network of one species by using the further information from gene expressions profile of related species. We present an algorithm to reconstruct the gene regulatory network named; F-MAP, which applies the knowledge about gene interactions from related species. Our algorithm sets a Bayesian framework to estimate the precision matrix of one species microarray gene expressions dataset to infer the Gaussian Graphical model of the network. The conjugate Wishart prior is used and the information from related species is applied to estimate the hyperparameters of the prior distribution by using the factor analysis. Applying the proposed algorithm on six related species of drosophila shows that the precision of reconstructed networks is improved considerably compared to the precision of networks constructed by other Bayesian approaches. PMID:28938012

Strawberry Maturity Neural Network Detectng System Based on Genetic Algorithm

NASA Astrophysics Data System (ADS)

Xu, Liming

The quick and non-detective detection of agriculture product is one of the measures to increase the precision and productivity of harvesting and grading. Having analyzed H frequency of different maturities in different light intensities, the results show that H frequency for the same maturity has little influence in different light intensities; Under the same light intensity, three strawberry maturities are changing in order. After having confirmed the H frequency section to distinguish the different strawberry maturity, the triplelayer feed-forward neural network system to detect strawberry maturity was designed by using genetic algorithm. The test results show that the detecting precision ratio is 91.7%, it takes 160ms to distinguish one strawberry. Therefore, the online non-detective detecting the strawberry maturity could be realized.

The Value of Listening to Grandmothers’ Infant-Feeding Stories

PubMed Central

Grassley, Jane S.; Eschiti, Valerie

2011-01-01

The purpose of this study was to examine the usefulness of storytelling as a foundation for communicating with grandmothers about breastfeeding. The benefits of storytelling are applied to an analysis of infant-feeding stories that grandmothers told during a focus group study conducted by the authors. Thirty-five grandmothers participated in the study. A qualitative content analysis of the interview transcripts revealed that grandmothers’ infant-feeding stories provided insights into the people (characters) and circumstances (setting) that affected their early experiences of infant feeding. By asking grandmothers to tell their stories, health-care professionals may understand the personal and cultural context grandmothers bring to their support of new mothers and facilitate a place for grandmothers’ voices to be heard. PMID:22654462

A Seed-Based Plant Propagation Algorithm: The Feeding Station Model

PubMed Central

Salhi, Abdellah

2015-01-01

The seasonal production of fruit and seeds is akin to opening a feeding station, such as a restaurant. Agents coming to feed on the fruit are like customers attending the restaurant; they arrive at a certain rate and get served at a certain rate following some appropriate processes. The same applies to birds and animals visiting and feeding on ripe fruit produced by plants such as the strawberry plant. This phenomenon underpins the seed dispersion of the plants. Modelling it as a queuing process results in a seed-based search/optimisation algorithm. This variant of the Plant Propagation Algorithm is described, analysed, tested on nontrivial problems, and compared with well established algorithms. The results are included. PMID:25821858

[Enteral nutrition: drug administration via feeding tube].

PubMed

Behnken, I; Gaschott, T; Stein, J

2005-11-01

Enteral nutrition support via a feeding tube is a preferred and broadly applied way of artificial nutrition in patients who cannot take up orally an adequate amount of nutrients. These patients often need simultaneous drug therapy as well. Thus, there is a high risk of drug-nutrient interactions. Although enteral nutrition is commonly used there is a lack of awareness and knowledge about the appropriate handling and drug administration via the feeding tube. On the one hand, drug-nutrient interactions can lead to clogging of the tube, on the other hand, the change in bioavailability of the drug can have a direct effect on the therapeutic effort. To optimise safety and efficacy of drug therapy in patients with feeding tubes, some basic rules have been set up.

Evolution and Development of Dual Ingestion Systems in Mammals: Notes on a New Thesis and Its Clinical Implications

PubMed Central

Alberts, Jeffrey R.; Pickler, Rita H.

2012-01-01

Traditionally, the development of oral feeding is viewed as a continuous, unitary process in which reflex-dominated sucking behavior gives rise to a more varied and volitional feeding behavior. In contrast, we consider the thesis that the infant develops two separable ingestive systems, one for suckling and one for feeding. First, we apply an evolutionary perspective, recognizing that suckling-feeding is a universal, mammalian developmental sequence. We find that in mammalian evolution, feeding systems in offspring were established prior to the evolution of lactation, and therefore suckling is a separable feature that was added to feeding. We next review an experimental literature that characterizes suckling and feeding as separable in terms of their topography, sensory controls, physiological controls, neural substrates, and experience-based development. Together, these considerations constitute a view of “dual ingestive systems.” The thesis, then, is that suckling is not a simple precursor of feeding but is a complete behavior that emerges, forms, and then undergoes a dissolution that overlaps with the emergence of independent feeding. This thesis guides us to focus differently on the challenges of properly managing and facilitating oral ingestion in infants, especially those born preterm, prior to the developmental onset of suckling. PMID:23028391

Evolution and development of dual ingestion systems in mammals: notes on a new thesis and its clinical implications.

PubMed

Alberts, Jeffrey R; Pickler, Rita H

2012-01-01

Traditionally, the development of oral feeding is viewed as a continuous, unitary process in which reflex-dominated sucking behavior gives rise to a more varied and volitional feeding behavior. In contrast, we consider the thesis that the infant develops two separable ingestive systems, one for suckling and one for feeding. First, we apply an evolutionary perspective, recognizing that suckling-feeding is a universal, mammalian developmental sequence. We find that in mammalian evolution, feeding systems in offspring were established prior to the evolution of lactation, and therefore suckling is a separable feature that was added to feeding. We next review an experimental literature that characterizes suckling and feeding as separable in terms of their topography, sensory controls, physiological controls, neural substrates, and experience-based development. Together, these considerations constitute a view of "dual ingestive systems." The thesis, then, is that suckling is not a simple precursor of feeding but is a complete behavior that emerges, forms, and then undergoes a dissolution that overlaps with the emergence of independent feeding. This thesis guides us to focus differently on the challenges of properly managing and facilitating oral ingestion in infants, especially those born preterm, prior to the developmental onset of suckling.

Evaluation of Amino Acid and Energy Utilization in Feedstuff for Swine and Poultry Diets

PubMed Central

Kong, C.; Adeola, O.

2014-01-01

An accurate feed formulation is essential for optimizing feed efficiency and minimizing feed cost for swine and poultry production. Because energy and amino acid (AA) account for the major cost of swine and poultry diets, a precise determination of the availability of energy and AA in feedstuffs is essential for accurate diet formulations. Therefore, the methodology for determining the availability of energy and AA should be carefully selected. The total collection and index methods are 2 major procedures for estimating the availability of energy and AA in feedstuffs for swine and poultry diets. The total collection method is based on the laborious production of quantitative records of feed intake and output, whereas the index method can avoid the laborious work, but greatly relies on accurate chemical analysis of index compound. The direct method, in which the test feedstuff in a diet is the sole source of the component of interest, is widely used to determine the digestibility of nutritional components in feedstuffs. In some cases, however, it may be necessary to formulate a basal diet and a test diet in which a portion of the basal diet is replaced by the feed ingredient to be tested because of poor palatability and low level of the interested component in the test ingredients. For the digestibility of AA, due to the confounding effect on AA composition of protein in feces by microorganisms in the hind gut, ileal digestibility rather than fecal digestibility has been preferred as the reliable method for estimating AA digestibility. Depending on the contribution of ileal endogenous AA losses in the ileal digestibility calculation, ileal digestibility estimates can be expressed as apparent, standardized, and true ileal digestibility, and are usually determined using the ileal cannulation method for pigs and the slaughter method for poultry. Among these digestibility estimates, the standardized ileal AA digestibility that corrects apparent ileal digestibility for basal endogenous AA losses, provides appropriate information for the formulation of swine and poultry diets. The total quantity of energy in feedstuffs can be partitioned into different components including gross energy (GE), digestible energy (DE), metabolizable energy (ME), and net energy based on the consideration of sequential energy losses during digestion and metabolism from GE in feeds. For swine, the total collection method is suggested for determining DE and ME in feedstuffs whereas for poultry the classical ME assay and the precision-fed method are applicable. Further investigation for the utilization of ME may be conducted by measuring either heat production or energy retention using indirect calorimetry or comparative slaughter method, respectively. This review provides information on the methodology used to determine accurate estimates of AA and energy availability for formulating swine and poultry diets. PMID:25050031

Evaluation of amino Acid and energy utilization in feedstuff for Swine and poultry diets.

PubMed

Kong, C; Adeola, O

2014-07-01

An accurate feed formulation is essential for optimizing feed efficiency and minimizing feed cost for swine and poultry production. Because energy and amino acid (AA) account for the major cost of swine and poultry diets, a precise determination of the availability of energy and AA in feedstuffs is essential for accurate diet formulations. Therefore, the methodology for determining the availability of energy and AA should be carefully selected. The total collection and index methods are 2 major procedures for estimating the availability of energy and AA in feedstuffs for swine and poultry diets. The total collection method is based on the laborious production of quantitative records of feed intake and output, whereas the index method can avoid the laborious work, but greatly relies on accurate chemical analysis of index compound. The direct method, in which the test feedstuff in a diet is the sole source of the component of interest, is widely used to determine the digestibility of nutritional components in feedstuffs. In some cases, however, it may be necessary to formulate a basal diet and a test diet in which a portion of the basal diet is replaced by the feed ingredient to be tested because of poor palatability and low level of the interested component in the test ingredients. For the digestibility of AA, due to the confounding effect on AA composition of protein in feces by microorganisms in the hind gut, ileal digestibility rather than fecal digestibility has been preferred as the reliable method for estimating AA digestibility. Depending on the contribution of ileal endogenous AA losses in the ileal digestibility calculation, ileal digestibility estimates can be expressed as apparent, standardized, and true ileal digestibility, and are usually determined using the ileal cannulation method for pigs and the slaughter method for poultry. Among these digestibility estimates, the standardized ileal AA digestibility that corrects apparent ileal digestibility for basal endogenous AA losses, provides appropriate information for the formulation of swine and poultry diets. The total quantity of energy in feedstuffs can be partitioned into different components including gross energy (GE), digestible energy (DE), metabolizable energy (ME), and net energy based on the consideration of sequential energy losses during digestion and metabolism from GE in feeds. For swine, the total collection method is suggested for determining DE and ME in feedstuffs whereas for poultry the classical ME assay and the precision-fed method are applicable. Further investigation for the utilization of ME may be conducted by measuring either heat production or energy retention using indirect calorimetry or comparative slaughter method, respectively. This review provides information on the methodology used to determine accurate estimates of AA and energy availability for formulating swine and poultry diets.

Ataxia Telangiectasia in Siblings: Oral Motor and Swallowing Characterization

PubMed Central

Rondon-Melo, Silmara; de Almeida, Isabel Junqueira; de Andrade, Claudia Regina Furquim; Sassi, Fernanda Chiarion; Molini-Avejonas, Daniela Regina

2017-01-01

Case series Patient: Male, 23 • Female, 20 Final Diagnosis: Ataxia telnagiectasia Symptoms: Gagging • coughing • hoarseness • articulatory inaccuracy Medication: — Clinical Procedure: Oral motor and swallowing assessment Specialty: Neurology Objective: Rare disease Background: The body of literature on oral motor and swallowing disorders in patients with ataxia telangiectasia (AT) is limited. Case Report: The purpose of this study was to characterize oral motor and swallowing disorders in two siblings with AT, based on oral motor and swallowing assessments. Specific procedures were applied for oral motor and swallowing assessments and both patients underwent videofluoroscopy (VFS). Case 1 presented vocal instability, change in postural control during feeding; food retention in oral cavity; slower oral transit time; and multiple swallowing (signs for solid and liquid). Case 2 presented parted lips at rest and reduced muscle strength; reduced strength and mobility of the tongue; vocal weakness and instability; reduced speech precision and intelligibility; decreased intonation pattern; food retention in oral cavity during feeding; slower oral transit time; multiple swallowing (signs for solid and liquid); poor bolus ejection; incoordination and difficulty in controlling the sips of water taken from the cup; altered cervical auscultation after swallowing and respiratory distress (liquid and puree). For both patients VFS results revealed laryngeal penetration for liquid. Conclusions: Although the literature describes the occurrence of dysarthria and swallowing disorders in patients with AT, little attention has been given to describing which oral motor deficits are responsible for these disorders. Early identification of swallowing alterations and rehabilitation could decrease the risk of aspiration pneumonia. Future studies are necessary in order to investigate the deterioration process of swallowing in AT and the influence of rehabilitation in maintaining functional health. PMID:28698541

Electrochemical Impedance Sensors for Monitoring Trace Amounts of NO3 in Selected Growing Media.

PubMed

Ghaffari, Seyed Alireza; Caron, William-O; Loubier, Mathilde; Normandeau, Charles-O; Viens, Jeff; Lamhamedi, Mohammed S; Gosselin, Benoit; Messaddeq, Younes

2015-07-21

With the advent of smart cities and big data, precision agriculture allows the feeding of sensor data into online databases for continuous crop monitoring, production optimization, and data storage. This paper describes a low-cost, compact, and scalable nitrate sensor based on electrochemical impedance spectroscopy for monitoring trace amounts of NO3- in selected growing media. The nitrate sensor can be integrated to conventional microelectronics to perform online nitrate sensing continuously over a wide concentration range from 0.1 ppm to 100 ppm, with a response time of about 1 min, and feed data into a database for storage and analysis. The paper describes the structural design, the Nyquist impedance response, the measurement sensitivity and accuracy, and the field testing of the nitrate sensor performed within tree nursery settings under ISO/IEC 17025 certifications.

Electrochemical Impedance Sensors for Monitoring Trace Amounts of NO3 in Selected Growing Media

PubMed Central

Ghaffari, Seyed Alireza; Caron, William-O.; Loubier, Mathilde; Normandeau, Charles-O.; Viens, Jeff; Lamhamedi, Mohammed S.; Gosselin, Benoit; Messaddeq, Younes

2015-01-01

With the advent of smart cities and big data, precision agriculture allows the feeding of sensor data into online databases for continuous crop monitoring, production optimization, and data storage. This paper describes a low-cost, compact, and scalable nitrate sensor based on electrochemical impedance spectroscopy for monitoring trace amounts of NO3− in selected growing media. The nitrate sensor can be integrated to conventional microelectronics to perform online nitrate sensing continuously over a wide concentration range from 0.1 ppm to 100 ppm, with a response time of about 1 min, and feed data into a database for storage and analysis. The paper describes the structural design, the Nyquist impedance response, the measurement sensitivity and accuracy, and the field testing of the nitrate sensor performed within tree nursery settings under ISO/IEC 17025 certifications. PMID:26197322

Influence of Mycotoxin Binders on the Oral Bioavailability of Doxycycline in Pigs.

PubMed

De Mil, Thomas; Devreese, Mathias; De Saeger, Sarah; Eeckhout, Mia; De Backer, Patrick; Croubels, Siska

2016-03-16

Mycotoxin binders are feed additives that aim to adsorb mycotoxins in the gastrointestinal tract of animals, making them unavailable for systemic absorption. The antimicrobial drug doxycycline (DOX) is often used in pigs and is administered through feed or drinking water; hence, DOX can come in contact with mycotoxin binders in the gastrointestinal tract. This paper describes the effect of four mycotoxin binders on the absorption of orally administered DOX in pigs. Two experiments were conducted: The first used a setup with bolus administration to fasted pigs at two different dosages of mycotoxin binder. In the second experiment, DOX and the binders were mixed in the feed at dosages recommended by the manufacturers (= field conditions). Interactions are possible between some of the mycotoxin binders dosed at 10 g/kg feed but not at 2 g/kg feed. When applying field conditions, no influences were seen on the plasma concentrations of DOX.

Planar microstrip YAGI antenna array

NASA Technical Reports Server (NTRS)

Huang, John (Inventor)

1993-01-01

A directional microstrip antenna includes a driven patch surrounded by an isolated reflector and one or more coplanar directors, all separated from a ground plane on the order of 0.1 wavelength or less to provide end fire beam directivity without requiring power dividers or phase shifters. The antenna may be driven at a feed point a distance from the center of the driven patch in accordance with conventional microstrip antenna design practices for H-plane coupled or horizontally polarized signals. The feed point for E-plane coupled or vertically polarized signals is at a greater distance from the center than the first distance. This feed point is also used for one of the feed signals for circularly polarized signals. The phase shift between signals applied to feed points for circularly polarized signals must be greater than the conventionally required 90 degrees and depends upon the antenna configuration.

Cholinergic interneurons in the feeding system of the pond snail Lymnaea stagnalis. III. Pharmacological dissection of the feeding rhythm.

PubMed

Elliott, C J

1992-05-29

The feeding activity of the pond snail Lymnaea stagnalis was stimulated by depolarization of a modulatory interneuron (SO) or of a N1 pattern-generating interneuron. The cholinergic antagonists phenyltrimethylammonium (PTMA), methylxylocholine (MeXCh), hexamethonium (HMT) and atropine (ATR) were applied at 0.5 mM in the bath and their effects on the rhythmic feeding pattern were monitored. Each of the antagonists slowed or blocked the feeding rhythm. The block was due to interference in the pattern generating network, not to disturbance of modulatory inputs. The experimental results favour a model in which the alternation of protraction (N1) and retraction (N2) phases occurs by recurrent inhibition. The results would be more difficult to explain on the reciprocal inhibition model. When all the N1 output was blocked, the N1 neurons fired rhythmic bursts endogenously.

Optimal actuator placement in adaptive precision trusses

NASA Technical Reports Server (NTRS)

Baycan, C. M.; Utku, S.; Das, S. K.; Wada, B. K.

1992-01-01

Actuator placement in adaptive truss structures is to cater to two needs: displacement control of precision points and preloading the elements to overcome joint slackness. Due to technological and financial considerations, the number of actuators available is much less than the degrees of freedom of precision points to be controlled and the degree of redundancy of the structure. An approach for optimal actuator location is outlined. Test cases to demonstrate the effectiveness of the scheme are applied to the Precision Segmented Reflector Truss.

Direct methanol feed fuel cell with reduced catalyst loading

NASA Technical Reports Server (NTRS)

Kindler, Andrew (Inventor)

1999-01-01

Improvements to direct feed methanol fuel cells include new protocols for component formation. Catalyst-water repellent material is applied in formation of electrodes and sintered before application of ionomer. A membrane used in formation of an electrode assembly is specially pre-treated to improve bonding between catalyst and membrane. The improved electrode and the pre-treated membrane are assembled into a membrane electrode assembly.

USSR Report, Agriculture

DTIC Science & Technology

1984-04-13

and Lipetsk and Tambov oblasts. It is necessary to better utilize peat for fer- tilizers and litter , to apply phosphorite and gypsum in a high...concentrates. Equipment was inadequately cleaned in shifting to production of feed formula- tions for broilers following preparation of feed mix...not prepare prestarter mixes for 1 to 4-day broilers . The author of this article was employed for many years in the Ptitseprom system and recalls

Carbon, nitrogen, and phosphorus budget in scampi (Macrobrachium rosenbergii) culture ponds.

PubMed

Sahu, Bharat Chandra; Adhikari, Subhendu; Mahapatra, Abhijit S; Dey, Lambodar

2013-12-01

Experiments were conducted for the study of nutrient budget in ten farmer's ponds (0.2-0.5 ha) in Orissa, India with a mean water depth of 1.0-1.2 m. Scampi (Macrobrachium rosenbergii) were stocked in these ponds at stocking density of 3.75-5.0/m(2). The average initial body weight of scampi was 0.02 mg. The culture period was for 4 months. Feed was the main input. Total feed applied to these ponds ranged from 945 to 2261 kg pond/cycle (crop). The feed conversion ratio varied 1.65 to 1.78. In addition to feed, rice straw, urea, and single super phosphate were applied to these ponds in small amounts for plankton production. At harvest time, the average weight of scampi varied from 60-90 g. The budget showed that feed was the major input of nitrogen (N), phosphorus (P), and carbon in these ponds. The inorganic fertilizer (urea and single super phosphate), organic fertilizer (rice straw and yeast extract), and inlet water, either from the initial fills or from rainwater, were the source of all other N, P, and organic carbon (OC) to these ponds. Total N applied to these ponds through all these inputs ranged from 44.45 to 103.98 kg N per crop, 12.23 to 28.79 kg P per crop, and from 381.54 to 905.22 kg OC per crop, respectively. Among all the inputs, feed alone accounted for 95.34 % N, 97.98 % P, and 94.27 % OC, respectively. Recovery of 16.34 to 38.66 kg N (average 29.27 kg), 1.28 to 3.02 kg P (average 2.29 kg), and 63.21 to 149.51 kg OC (average 113.20 kg), respectively, by the scampi harvest were observed in these ponds. Thus, harvest of scampi accounted for recovery of 35.18 to 39.01 (average 36.85%) of added N, 10.09 to 10.97 (average 10.44%) of added P, and 7.57 to 17.12 (average 16.34%) of added OC, respectively.

2006 Precision Strike Technology Symposium

DTIC Science & Technology

2006-10-19

s Navy Unique Joint system 14 A/C Unique Components Framework JMPS Common Components Crypto Key GCCS-M Interface Carrier Intel Feed Carrier...210 GPS Prediction CUPC GPS Crypto Key TAMMAC SLAM-ER GPS Almanac ETIRMS PMA-281 NGMS PMA-209 Boeing PMA-201 Raytheon ESC (USAF) Hill AFB PMA-234 PMA...242 F/A-18 UPC GPS Prediction CUPC GPS Crypto Key TAMMAC SLAM-ER GPS Almanac HARM WASP Framework ARC-210 ETIRMS PMA-281 Integration/Test/ Support TLAM

Proceedings of the 1989 Antenna Applications Symposium. Volume 1

DTIC Science & Technology

1990-03-01

of this antenna is the absence of spillover sidelobes where energy from the feed spills past the edge of the reflector to give a 112 relatively high ... High Gain Receive Cylindrical, Array 381 Antenna WIth Ful Azimuth Coverage," J. C. Herper, A. M. bucceri ’&nd J. J. Stangel 22. "Conformal Ac-tive...Phased Array Demonstration," � Jerome D. Hanfling 23 " High Precision Frequency Locking technique for Active 441 Microstrip Antenna Arrays,’ Gabriel

Visualizing Non Infectious and Infectious Anopheles gambiae Blood Feedings in Naive and Saliva-Immunized Mice

PubMed Central

Choumet, Valerie; Attout, Tarik; Chartier, Loïc; Khun, Huot; Sautereau, Jean; Robbe-Vincent, Annie; Brey, Paul; Huerre, Michel; Bain, Odile

2012-01-01

Background Anopheles gambiae is a major vector of malaria and lymphatic filariasis. The arthropod-host interactions occurring at the skin interface are complex and dynamic. We used a global approach to describe the interaction between the mosquito (infected or uninfected) and the skin of mammals during blood feeding. Methods Intravital video microscopy was used to characterize several features during blood feeding. The deposition and movement of Plasmodium berghei sporozoites in the dermis were also observed. We also used histological techniques to analyze the impact of infected and uninfected feedings on the skin cell response in naive mice. Results The mouthparts were highly mobile within the skin during the probing phase. Probing time increased with mosquito age, with possible effects on pathogen transmission. Repletion was achieved by capillary feeding. The presence of sporozoites in the salivary glands modified the behavior of the mosquitoes, with infected females tending to probe more than uninfected females (86% versus 44%). A white area around the tip of the proboscis was observed when the mosquitoes fed on blood from the vessels of mice immunized with saliva. Mosquito feedings elicited an acute inflammatory response in naive mice that peaked three hours after the bite. Polynuclear and mast cells were associated with saliva deposits. We describe the first visualization of saliva in the skin by immunohistochemistry (IHC) with antibodies directed against saliva. Both saliva deposits and sporozoites were detected in the skin for up to 18 h after the bite. Conclusion This study, in which we visualized the probing and engorgement phases of Anopheles gambiae blood meals, provides precise information about the behavior of the insect as a function of its infection status and the presence or absence of anti-saliva antibodies. It also provides insight into the possible consequences of the inflammatory reaction for blood feeding and pathogen transmission. PMID:23272060

Visualizing non infectious and infectious Anopheles gambiae blood feedings in naive and saliva-immunized mice.

PubMed

Choumet, Valerie; Attout, Tarik; Chartier, Loïc; Khun, Huot; Sautereau, Jean; Robbe-Vincent, Annie; Brey, Paul; Huerre, Michel; Bain, Odile

2012-01-01

Anopheles gambiae is a major vector of malaria and lymphatic filariasis. The arthropod-host interactions occurring at the skin interface are complex and dynamic. We used a global approach to describe the interaction between the mosquito (infected or uninfected) and the skin of mammals during blood feeding. Intravital video microscopy was used to characterize several features during blood feeding. The deposition and movement of Plasmodium berghei sporozoites in the dermis were also observed. We also used histological techniques to analyze the impact of infected and uninfected feedings on the skin cell response in naive mice. The mouthparts were highly mobile within the skin during the probing phase. Probing time increased with mosquito age, with possible effects on pathogen transmission. Repletion was achieved by capillary feeding. The presence of sporozoites in the salivary glands modified the behavior of the mosquitoes, with infected females tending to probe more than uninfected females (86% versus 44%). A white area around the tip of the proboscis was observed when the mosquitoes fed on blood from the vessels of mice immunized with saliva. Mosquito feedings elicited an acute inflammatory response in naive mice that peaked three hours after the bite. Polynuclear and mast cells were associated with saliva deposits. We describe the first visualization of saliva in the skin by immunohistochemistry (IHC) with antibodies directed against saliva. Both saliva deposits and sporozoites were detected in the skin for up to 18 h after the bite. This study, in which we visualized the probing and engorgement phases of Anopheles gambiae blood meals, provides precise information about the behavior of the insect as a function of its infection status and the presence or absence of anti-saliva antibodies. It also provides insight into the possible consequences of the inflammatory reaction for blood feeding and pathogen transmission.

Evaluation of a High Throughput Starch Analysis Optimised for Wood

PubMed Central

Bellasio, Chandra; Fini, Alessio; Ferrini, Francesco

2014-01-01

Starch is the most important long-term reserve in trees, and the analysis of starch is therefore useful source of physiological information. Currently published protocols for wood starch analysis impose several limitations, such as long procedures and a neutralization step. The high-throughput standard protocols for starch analysis in food and feed represent a valuable alternative. However, they have not been optimised or tested with woody samples. These have particular chemical and structural characteristics, including the presence of interfering secondary metabolites, low reactivity of starch, and low starch content. In this study, a standard method for starch analysis used for food and feed (AOAC standard method 996.11) was optimised to improve precision and accuracy for the analysis of starch in wood. Key modifications were introduced in the digestion conditions and in the glucose assay. The optimised protocol was then evaluated through 430 starch analyses of standards at known starch content, matrix polysaccharides, and wood collected from three organs (roots, twigs, mature wood) of four species (coniferous and flowering plants). The optimised protocol proved to be remarkably precise and accurate (3%), suitable for a high throughput routine analysis (35 samples a day) of specimens with a starch content between 40 mg and 21 µg. Samples may include lignified organs of coniferous and flowering plants and non-lignified organs, such as leaves, fruits and rhizomes. PMID:24523863

Breast-feeding influences on later life--cardiovascular disease.

PubMed

Leon, D A; Ronalds, G

2009-01-01

Current evidence, almost exclusively from observational studies, provides a rather mixed picture. From the few studies that have been able to look at fatal or non-fatal cardiovascular events, there is little indication that breast-feeding is associated with either an increased or decreased risk. With respect to blood pressure, the meta-analyses suggest a small but statistically significant lowering of around 1 mmHg SBP associated with having been breast-fed in infancy. However, there is a strong indication from the meta-analyses that even this small effect may partly be accounted for by publication bias. The strongest evidence for an effect of breast-feeding reviewed in this chapter is for serum lipids, where there is good evidence that being breast-fed is associated with an increase in serum total cholesterol in infancy. In childhood there appears to be no association, while in adults there is some indication of breast-feeding being associated with a small decline in total cholesterol levels. As already outlined at the start of the chapter, this whole area of research is made particularly difficult by the fact that breast-feeding can be defined in many different ways. Some studies use definitions that are equivalent to exclusive breast-feeding prior to weaning, while others define it as having ever been breast-fed. This problem of classification is likely to dilute any real associations that may exist. The other major problem is one of interpretation. A result implying that breast-feeding is a "good thing" for cardiovascular health could equally be construed as evidence for a "bad" effect of bottle-feeding. From these data alone, we cannot convincingly determine which conclusion is correct. This is not simply a philosophical debating point. As discussed above in relation to the interpretation of results from the randomised trial of infant feeding, the issue has implications for all research on this topic. Some progress in this area will be made if studies are conducted which define breast-feeding in a more precise and comparable way, and take account of the composition of alternative infant feeds. This will be most easily done by following up more recent study populations that were originally recruited to look at shorter-term effects of infant feeding on outcomes such as growth. With respect to randomised trial evidence, looking at the cardiovascular disease risk profiles of children (and later adults) who were part of the PROBIT trial in Belarus (see Chapters 5 and 10) is likely to prove fruitful.

Island phytophagy: explaining the remarkable diversity of plant-feeding insects

PubMed Central

Joy, Jeffrey B.; Crespi, Bernard J.

2012-01-01

Plant-feeding insects have undergone unparalleled diversification among different plant taxa, yet explanations for variation in their diversity lack a quantitative, predictive framework. Island biogeographic theory has been applied to spatially discrete habitats but not to habitats, such as host plants, separated by genetic distance. We show that relationships between the diversity of gall-inducing flies and their host plants meet several fundamental predictions from island biogeographic theory. First, plant-taxon genetic distinctiveness, an integrator for long-term evolutionary history of plant lineages, is a significant predictor of variance in the diversity of gall-inducing flies among host-plant taxa. Second, range size and structural complexity also explain significant proportions of the variance in diversity of gall-inducing flies among different host-plant taxa. Third, as with other island systems, plant-lineage age does not predict species diversity. Island biogeographic theory, applied to habitats defined by genetic distance, provides a novel, comprehensive framework for analysing and explaining the diversity of plant-feeding insects and other host-specific taxa. PMID:22553094

Island phytophagy: explaining the remarkable diversity of plant-feeding insects.

PubMed

Joy, Jeffrey B; Crespi, Bernard J

2012-08-22

Plant-feeding insects have undergone unparalleled diversification among different plant taxa, yet explanations for variation in their diversity lack a quantitative, predictive framework. Island biogeographic theory has been applied to spatially discrete habitats but not to habitats, such as host plants, separated by genetic distance. We show that relationships between the diversity of gall-inducing flies and their host plants meet several fundamental predictions from island biogeographic theory. First, plant-taxon genetic distinctiveness, an integrator for long-term evolutionary history of plant lineages, is a significant predictor of variance in the diversity of gall-inducing flies among host-plant taxa. Second, range size and structural complexity also explain significant proportions of the variance in diversity of gall-inducing flies among different host-plant taxa. Third, as with other island systems, plant-lineage age does not predict species diversity. Island biogeographic theory, applied to habitats defined by genetic distance, provides a novel, comprehensive framework for analysing and explaining the diversity of plant-feeding insects and other host-specific taxa.

Examination of the torque required to passively palmar abduct the thumb CMC joint in a pediatric population with hemiplegia and stroke.

PubMed

Stirling, Leia; Ahmad, Mona Qureshi; Kelty-Stephen, Damian; Correia, Annette

2015-12-16

Many activities of daily living involve precision grasping and bimanual manipulation, such as putting toothpaste on a toothbrush or feeding oneself. However, children afflicted by stroke, cerebral palsy, or traumatic brain injury may have lost or never had the ability to actively and accurately control the thumb. To translate insights from adult rehabilitation robotics to innovative therapies for hand rehabilitation in pediatric care, specifically for thumb deformities, an understanding of the torque needed to abduct the thumb to assist grasping tasks is required. Participants (n=16, 10 female, 13.2±3.1 years) had an upper extremity evaluation and measures were made of their passive range of motion, anthropometrics, and torques to abduct the thumb for both their affected and non-affected sides. Torque measures were made using a custom wrist orthosis that was adjusted for each participant. The torque to achieve maximum abduction was 1.47±0.61inlb for the non-affected side and 1.51±0.68inlb for the affected side, with a maximum recorded value of 4.87inlb. The overall maximum applied torque was observed during adduction and was 5.10inlb. We saw variation in the applied torque, which could have been due to the applied torques by the Occupational Therapist or the participant actively assisting or resisting the motion rather than remaining passive. We expect similar muscle and participant variation to exist with an assistive device. Thus, the data presented here can be used to inform the specifications for the development of an assistive thumb orthosis for children with "thumb-in-palm" deformity. Copyright © 2015 Elsevier Ltd. All rights reserved.

Multi-residue analysis of 36 priority and emerging pollutants in marine echinoderms (Holothuria tubulosa) and marine sediments by solid-liquid extraction followed by dispersive solid phase extraction and liquid chromatography-tandem mass spectrometry analysis.

PubMed

Martín, J; Zafra-Gómez, A; Hidalgo, F; Ibáñez-Yuste, A J; Alonso, E; Vilchez, J L

2017-05-01

Marine echinoderms are filter-feeding invertebrates widely distributed along the coasts, and which are therefore extensively exposed to anthropogenic xenobiotics. They can serve as good sentinels for monitoring a large variety of contaminants in marine ecosystems. In this context, a multi-residue analytical method has been validated and applied to Holothuria tubulosa specimens and marine sediments for the determination of 36 organic compounds, which belong to some of the most problematic groups of emerging and priority pollutants (perfluoroalkyl compounds, estrogens, parabens, benzophenones, plasticizers, surfactants, brominated flame retardants and alkylphenols). Lyophilization of samples prior to solvent extraction and clean-up of extracts with C18, followed by liquid chromatography-tandem mass spectrometry analysis, is proposed. A Box-Behnken design was used for optimization of the most influential variables affecting the extraction and clean-up steps. For validation, matrix-matched calibration and recovery assay were applied. Linearity (% r 2 ) higher than 99%, recoveries between 80% and 114% (except in LAS and NP1EO), RSD (precision) lower than 15% and limits of quantification between 0.03 and 12.5ngg -1 dry weight (d.w.) were achieved. The method was applied to nine samples of Holothuria collected along the coast of Granada (Spain), and to marine sediments around the animals. The results demonstrated high bioaccumulation of certain pollutants. A total of 25 out of the 36 studied compounds were quantified, being surfactants, alkylphenols, perfluoroalkyl compounds, triclocarban and parabens the most frequently detected. Nonylphenol was found in the highest concentration (340 and 323ngg -1 d.w. in sediment and Holothuria samples, respectively). Copyright © 2017 Elsevier B.V. All rights reserved.

Estimation of costs for control of Salmonella in high-risk feed materials and compound feed

PubMed Central

Wierup, Martin; Widell, Stig

2014-01-01

Introduction Feed is a potential and major source for introducing Salmonella into the animal-derived food chain. This is given special attention in the European Union (EU) efforts to minimize human food-borne Salmonella infections from animal-derived food. The objective of this study was to estimate the total extra cost for preventing Salmonella contamination of feed above those measures required to produce commercial feed according to EU regulation (EC) No 183/2005. The study was carried out in Sweden, a country where Salmonella infections in food-producing animals from feed have largely been eliminated. Methods On the initiative and leadership of the competent authority, the different steps of feed production associated with control of Salmonella contamination were identified. Representatives for the major feed producers operating in the Swedish market then independently estimated the annual mean costs during the years 2009 and 2010. The feed producers had no known incentives to underestimate the costs. Results and discussion The total cost for achieving a Salmonella-safe compound feed, when such a control is established, was estimated at 1.8–2.3 € per tonne of feed. Of that cost, 25% relates to the prevention of Salmonella contaminated high-risk vegetable feed materials (mainly soybean meal and rapeseed meal) from entering feed mills, and 75% for measures within the feed mills. Based on the feed formulations applied, those costs in relation to the farmers’ 2012 price for compound feed were almost equal for broilers and dairy cows (0.7%). Due to less use of protein concentrate to fatten pigs, the costs were lower (0.6%). These limited costs suggest that previous recommendations to enforce a Salmonella-negative policy for animal feed are realistic and economically feasible to prevent a dissemination of the pathogen to animal herds, their environment, and potentially to human food products. PMID:24959328

40 CFR 412.20 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.20 Applicability. This subpart applies to discharges resulting from the production areas at dry lot and wet lot duck CAFOs. This subpart does not apply to such CAFOs with less than the following capacities: 5,000 ducks. ...

40 CFR 412.20 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.20 Applicability. This subpart applies to discharges resulting from the production areas at dry lot and wet lot duck CAFOs. This subpart does not apply to such CAFOs with less than the following capacities: 5,000 ducks. ...

40 CFR 412.20 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.20 Applicability. This subpart applies to discharges resulting from the production areas at dry lot and wet lot duck CAFOs. This subpart does not apply to such CAFOs with less than the following capacities: 5,000 ducks. ...

40 CFR 412.20 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.20 Applicability. This subpart applies to discharges resulting from the production areas at dry lot and wet lot duck CAFOs. This subpart does not apply to such CAFOs with less than the following capacities: 5,000 ducks. ...

40 CFR 412.20 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

... CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.20 Applicability. This subpart applies to discharges resulting from the production areas at dry lot and wet lot duck CAFOs. This subpart does not apply to such CAFOs with less than the following capacities: 5,000 ducks. ...

High-precision x-ray spectroscopy of highly charged ions with microcalorimeters

NASA Astrophysics Data System (ADS)

Kraft-Bermuth, S.; Andrianov, V.; Bleile, A.; Echler, A.; Egelhof, P.; Grabitz, P.; Ilieva, S.; Kilbourne, C.; Kiselev, O.; McCammon, D.; Meier, J.

2013-09-01

The precise determination of the energy of the Lyman α1 and α2 lines in hydrogen-like heavy ions provides a sensitive test of quantum electrodynamics in very strong Coulomb fields. To improve the experimental precision, the new detector concept of microcalorimeters is now exploited for such measurements. Such detectors consist of compensated-doped silicon thermistors and Pb or Sn absorbers to obtain high quantum efficiency in the energy range of 40-70 keV, where the Doppler-shifted Lyman lines are located. For the first time, a microcalorimeter was applied in an experiment to precisely determine the transition energy of the Lyman lines of lead ions at the experimental storage ring at GSI. The energy of the Ly α1 line E(Ly-α1, 207Pb81+) = (77937 ± 12stat ± 25syst) eV agrees within error bars with theoretical predictions. To improve the experimental precision, a new detector array with more pixels and better energy resolution was equipped and successfully applied in an experiment to determine the Lyman-α lines of gold ions 197Au78+.

Significant improvement of intestinal microbiota of gibel carp (Carassius auratus gibelio) after traditional Chinese medicine feeding.

PubMed

Wu, Z B; Gatesoupe, F-J; Li, T T; Wang, X H; Zhang, Q Q; Feng, D Y; Feng, Y Q; Chen, H; Li, A H

2018-03-01

Increasing attention has been attracted to intestinal microbiota, due to interactions with nutrition, metabolism and immune defence of the host. Traditional Chinese medicine (TCM) feed additives have been applied in aquaculture to improve fish health, but the interaction with fish gut microbiota is still poorly understood. This study aimed to explore the effect of adding TCM in feed on the intestinal microbiota of gibel carp (Carassius auratus gibelio). Bacterial communities of 16 fish intestinal contents and one water sample were characterized by high-throughput sequencing and analysis of the V4-V5 region of the 16S rRNA gene. The results showed that the composition and structure of the bacterial community were significantly altered by the TCM feeding. Some phyla increased markedly (Proteobacteria, Actinobacteria, Acidobacteria, etc.), while Fusobacteria were significantly reduced. Concurrently, the richness and diversity of the taxonomic units increased, and the microbiota composition of TCM-treated fish was more homogeneous among individuals. At the genus level, the addition of TCM tended to reduce the incidence of potential pathogens (Aeromonas, Acinetobacter and Shewanella), while stimulating the emergence of some potential probiotics (Lactobacillus, Lactococcus, Bacillus and Pseudomonas). These data suggested that the feed additive could regulate the fish intestinal microbiota by reinforcing the microbial balance. This study may provide useful information for further application of TCM for diseases prevention and stress management in aquaculture. © 2017 The Society for Applied Microbiology.

An Online Respiratory Quotient-Feedback Strategy of Feeding Yeast Extract for Efficient Arachidonic Acid Production by Mortierella alpina

PubMed Central

Li, Xiangyu; Yu, Chao; Yao, Jianming; Wang, Zhiming; Lu, Shuhuan

2018-01-01

Mortierella alpina (M. alpina) is well known for arachidonic acid (ARA) production. However, low efficiency and unstableness are long existed problems for industrial production of ARA by M. alpina due to the lack of online regulations. The aim of the present work is to develop an online-regulation strategy for efficient and stable ARA production in industry. The strategy was developed in 50 L fermenters and then applied in a 200 m3 fermenter. Results indicated that yeast extract (YE) highly increased cell growth in shake flask, it was then used in bioreactor fermentation by various feeding strategies. Feeding YE to control respiratory quotient (RQ) at 1.1 during 0–48 h and at 1.5 during 48–160 h, dry cell weight, and ARA titer reached 53.1 and 11.49 g/L in 50 L fermenter, which were increased by 79.4 and 36.9% as compared to that without YE feeding, respectively. Then, the online RQ-feedback strategy was applied in 200 m3 bioreactor fermentation and an average ARA titer of 16.82 g/L was obtained from 12 batches, which was 41.0% higher than the control batches. This is the first report on successful application of online RQ-feedback control of YE in ARA production, especially in an industrial scale of 200 m3 fermentation. It could be applied to other industrial production of microbial oil by oleaginous microorganisms. PMID:29404320

Characterization of Dietary Energy in Swine Feed and Feed Ingredients: A Review of Recent Research Results

PubMed Central

Velayudhan, D. E.; Kim, I. H.; Nyachoti, C. M.

2015-01-01

Feed is single most expensive input in commercial pork production representing more than 50% of the total cost of production. The greatest proportion of this cost is associated with the energy component, thus making energy the most important dietary in terms of cost. For efficient pork production, it is imperative that diets are formulated to accurately match dietary energy supply to requirements for maintenance and productive functions. To achieve this goal, it is critical that the energy value of feeds is precisely determined and that the energy system that best meets the energy needs of a pig is used. Therefore, the present review focuses on dietary supply and needs for pigs and the available energy systems for formulating swine diets with particular emphasis on the net energy system. In addition to providing a more accurate estimate of the energy available to the animal in an ingredient and the subsequent diet, diets formulated using the this system are typically lower in crude protein, which leads to additional benefits in terms of reduced nitrogen excretion and consequent environmental pollution. Furthermore, using the net energy system may reduce diet cost as it allows for increased use of feedstuffs containing fibre in place of feedstuffs containing starch. A brief review of the use of distiller dried grains with solubles in swine diets as an energy source is included. PMID:25557670

Characterization of dietary energy in Swine feed and feed ingredients: a review of recent research results.

PubMed

Velayudhan, D E; Kim, I H; Nyachoti, C M

2015-01-01

Feed is single most expensive input in commercial pork production representing more than 50% of the total cost of production. The greatest proportion of this cost is associated with the energy component, thus making energy the most important dietary in terms of cost. For efficient pork production, it is imperative that diets are formulated to accurately match dietary energy supply to requirements for maintenance and productive functions. To achieve this goal, it is critical that the energy value of feeds is precisely determined and that the energy system that best meets the energy needs of a pig is used. Therefore, the present review focuses on dietary supply and needs for pigs and the available energy systems for formulating swine diets with particular emphasis on the net energy system. In addition to providing a more accurate estimate of the energy available to the animal in an ingredient and the subsequent diet, diets formulated using the this system are typically lower in crude protein, which leads to additional benefits in terms of reduced nitrogen excretion and consequent environmental pollution. Furthermore, using the net energy system may reduce diet cost as it allows for increased use of feedstuffs containing fibre in place of feedstuffs containing starch. A brief review of the use of distiller dried grains with solubles in swine diets as an energy source is included.

Precision displacement reference system

DOEpatents

Bieg, Lothar F.; Dubois, Robert R.; Strother, Jerry D.

2000-02-22

A precision displacement reference system is described, which enables real time accountability over the applied displacement feedback system to precision machine tools, positioning mechanisms, motion devices, and related operations. As independent measurements of tool location is taken by a displacement feedback system, a rotating reference disk compares feedback counts with performed motion. These measurements are compared to characterize and analyze real time mechanical and control performance during operation.

Low-income mothers’ feeding goals predict observed home mealtime and child feeding practices

PubMed Central

Pesch, Megan H.; Miller, Alison L.; Appugliese, Danielle P.; Kaciroti, Niko; Rosenblum, Katherine L.; Lumeng, Julie C.

2016-01-01

Background Mothers’ goals are important for health behavior change, and engagement in child obesity interventions. It is unknown if maternal feeding goals are associated with observed home mealtime or feeding practices. The objective of this study was to examine the association of four common feeding goals (restrict junk food, promote fruit or vegetable intake, promote autonomy in eating, and prevent obesity) with mothers’ observed home mealtime and feeding practices. Methods Low-income mothers (N = 265) of children (mean child age 70.8 months) participated in a semi-structured interview about child feeding. A coding scheme was developed and reliably applied to identify mothers’ feeding goals from transcripts. Mothers’ observed home mealtime and feeding practices were reliably coded from home mealtimes and a laboratory eating protocol. Mothers completed a questionnaire and reported demographics. Participant weights and heights were obtained. Regression models were used to test the association of each feeding goal with observed maternal practice, controlling for covariates. Results The goal of restricting junk food was associated with the child always eating at a table (OR 2.87, 95% CI (1.39–5.96) p =0.005), but not with the mother restricting junk food. The goal of promoting fruit or vegetable intake was associated with observationally promoting vegetables (OR 1.41, 95% CI (1.09–1.84), p = 0.01). The goals of promoting autonomy and preventing obesity were not associated with any observed maternal home mealtime or feeding practices. Conclusions While mothers’ goals to restrict junk food and promote fruit or vegetable intake were associated with observed home mealtime and feeding practices, promoting autonomy and preventing obesity were not. Increased understanding of why low-income mothers may not translate certain feeding goals into practices may inform childhood obesity interventions. PMID:27558923

The effects of enteral feeding improvement massage on premature infants: A randomised controlled trial.

PubMed

Kim, Hee-Young; Bang, Kyung-Sook

2018-01-01

To prove the effects of an enteral feeding improvement massage for premature infants with regard to their feeding, growing and superior mesentery artery blood flow aspect by a randomised controlled trial. Premature infants have feeding-related problems related to eating and absorbing nutrition due to their immature gastrointestinal function. Studies regarding the effectiveness of premature infants' enteral feeding improvement by tactile stimulation massage are rare. The study group was composed of 55 patients. Of the 55 patients, 26 were randomised into an experimental group and 29 were randomised into a control group. They were all born <34 weeks of gestational age between 1 July 2011 and 30 March 2012. Premature infants in the experimental group received enteral feeding improvement massage twice a day for 14 days, and infants in the control group received a sham exercise. The collected data were analysed by spss 19.0, through t test, chi-square test (Fisher's exact) and ANCOVA. (i) The experimental group had reached the day of full enteral feeding significantly faster. (ii) The experimental group had a higher superior mesentery artery peak velocity (V max ) and lower RI (resistant index). (iii) The experimental group of the feeding-intolerant subgroup had a higher superior mesentery artery V max and V min . (iv) The experimental group had a heavier weight and larger head circumference after 14 days. This study demonstrates that enteral feeding improvement massage can be helpful for achieving earlier full enteral feeding, more increased superior mesentery artery, and faster growing. In particular, it can be a therapeutic, independent and evidence-based nursing intervention for feeding-intolerant premature infants. Neonatal nurses in neonatal intensive care unit can apply enteral feeding improvement massage massage for feeding-intolerant infants. © 2017 John Wiley & Sons Ltd.

A review of feed efficiency in swine: biology and application.

PubMed

Patience, John F; Rossoni-Serão, Mariana C; Gutiérrez, Néstor A

2015-01-01

Feed efficiency represents the cumulative efficiency with which the pig utilizes dietary nutrients for maintenance, lean gain and lipid accretion. It is closely linked with energy metabolism, as the oxidation of carbon-containing components in the feed drive all metabolic processes. While much is known about nutrient utilization and tissue metabolism, blending these subjects into a discussion on feed efficiency has proven to be difficult. For example, while increasing dietary energy concentration will almost certainly increase feed efficiency, the correlation between dietary energy concentration and feed efficiency is surprisingly low. This is likely due to the plethora of non-dietary factors that impact feed efficiency, such as the environment and health as well as individual variation in maintenance requirements, body composition and body weight. Nonetheless, a deeper understanding of feed efficiency is critical at many levels. To individual farms, it impacts profitability. To the pork industry, it represents its competitive position against other protein sources. To food economists, it means less demand on global feed resources. There are environmental and other societal implications as well. Interestingly, feed efficiency is not always reported simply as a ratio of body weight gain to feed consumed. This review will explain why this arithmetic calculation, as simple as it initially seems, and as universally applied as it is in science and commerce, can often be misleading due to errors inherent in recording of both weight gain and feed intake. This review discusses the importance of feed efficiency, the manner in which it can be measured and reported, its basis in biology and approaches to its improvement. It concludes with a summary of findings and recommendations for future efforts.

A breast-feeding promotion and support program a randomized trial in The Netherlands.

PubMed

Kools, Els J; Thijs, Carel; Kester, Arnold D M; van den Brandt, Piet A; de Vries, Hein

2005-01-01

In the Netherlands, the initiation rate of breast-feeding (BF) was 80% in 2002, but only 35% of the mothers continued to breast-feed for 3 months. This study examined the effectiveness of a breast-feeding promotion program to increase the continuation of breast-feeding. A cluster-randomized intervention trial was used. Ten child health care centers in three regions of the home health care were randomly allocated to the program or usual care. Elements in the program were health counseling, measures to enhance cooperation, early signaling of breast-feeding problems and continuity of care, and lactation consultancy. Pregnant mothers who applied for home health care in the intervention or usual care regions were enrolled and were followed up from pregnancy until 6 months postpartum (n = 683). The primary outcome measure was the continuation of breast-feeding until at least 3 months. The 3-month breast-feeding rate was 32% in the intervention and 38% in the control groups (OR = 0.79, 95% CI = 0.58-1.08). The program was not effective. We discuss possible explanations from the design and execution of the trial and give some points for improvement of our program, such as the categories of caregivers involved and the number and duration of contacts after parturition.

Use of fish species from different trophic levels to control algae and water quality: An enclosure experiment in eutrophic area of Xiaojiang River.

PubMed

Hu, Lian; Yang, Zhi; Pan, Xiaojie; Zhao, Na; Peng, Jianhua; Wan, Chengyan

2017-01-01

The effects of stocking both filter-feeding fish and piscivorous fish were compared to the effects of stocking only filter-feeding fish for suppressing algal blooms and improving water quality in the impoundment area of Xiaojiang River where catfish were dominant. Using only filter-feeding fish for algal suppression and water quality control was more effective in the short-term, but use of both filter-feeding fish and piscivorous fish was better in the long-term. Obvious suppression of phytoplankton biomass (PB) only occurred during the first 14 days regardless of the fish stocked. Adding fish to the enclosure clearly alters phytoplankton community structure and introducing piscivorous fish to an enclosure stocked with filter-feeding fish changed the relative densities of dominant algae species. While stocking filter-feeding fish decreased total nitrogen concentration by removing phytoplankton, it did not effectively decrease total phosphorus and Chlorophyll a concentrations. Introducing piscivorous fish to the enclosure weakened the relationship between nutrients and phytoplankton. Results indicate that stocking only filter-feeding fish to improve water quality and suppress phytoplankton in an impoundment area is insufficient and other technologies and means should be applied simultaneously.

Determinants of breast-feeding patterns in an urban society of India.

PubMed

Nath, D C; Goswami, G

1997-08-01

Breast feeding is the focus of rapidly growing interest in many areas of demographic research. However, relatively few rigorous studies on breast-feeding patterns and correlates in contemporary India have been published. This study uses data from a retrospective survey conducted in 1991-1992 to investigate current breast-feeding patterns and to identify the key factors that influence the duration of exclusive breast feeding and infant's age at the time of weaning in an urban Hindu society of the northeast Indian state of Assam. Applying life table procedures and a hazards regression model, we found evidence that the median duration of exclusive breast feeding and infant's age at the time of weaning were negatively associated with mother's education, per capita income, and social status of the household. Those infants who were breast-fed longer at night than in the daytime were also at greater risk of earlier introduction of non-breast-milk foods and of earlier termination of breast feeding than infants who were breast-fed longer during the day. Gender bias toward males in rearing infants prevails in this urban society, and male infants were found to have a significantly lower risk of early weaning than female infants.

The work of the European Union Reference Laboratory for Food Additives (EURL) and its support for the authorisation process of feed additives in the European Union: a review

PubMed Central

von Holst, Christoph; Robouch, Piotr; Bellorini, Stefano; de la Huebra, María José González; Ezerskis, Zigmas

2016-01-01

ABSTRACT This paper describes the operation of the European Union Reference Laboratory for Feed Additives (EURL) and its role in the authorisation procedure of feed additives in the European Union. Feed additives are authorised according to Regulation (EC) No. 1831/2003, which introduced a completely revised authorisation procedure and also established the EURL. The regulations authorising feed additives contain conditions of use such as legal limits of the feed additives, which require the availability of a suitable method of analysis for official control purposes under real world conditions. It is the task of the EURL to evaluate the suitability of analytical methods as proposed by the industry for this purpose. Moreover, the paper shows that one of the major challenges is the huge variety of the methodology applied in feed additive analysis, thus requiring expertise in quite different analytical areas. In order to cope with this challenge, the EURL is supported by a network of national reference laboratories (NRLs) and only the merged knowledge of all NRLs allows for a scientifically sound assessment of the analytical methods. PMID:26540604

Precise attitude rate estimation using star images obtained by mission telescope for satellite missions

NASA Astrophysics Data System (ADS)

Inamori, Takaya; Hosonuma, Takayuki; Ikari, Satoshi; Saisutjarit, Phongsatorn; Sako, Nobutada; Nakasuka, Shinichi

2015-02-01

Recently, small satellites have been employed in various satellite missions such as astronomical observation and remote sensing. During these missions, the attitudes of small satellites should be stabilized to a higher accuracy to obtain accurate science data and images. To achieve precise attitude stabilization, these small satellites should estimate their attitude rate under the strict constraints of mass, space, and cost. This research presents a new method for small satellites to precisely estimate angular rate using star blurred images by employing a mission telescope to achieve precise attitude stabilization. In this method, the angular velocity is estimated by assessing the quality of a star image, based on how blurred it appears to be. Because the proposed method utilizes existing mission devices, a satellite does not require additional precise rate sensors, which makes it easier to achieve precise stabilization given the strict constraints possessed by small satellites. The research studied the relationship between estimation accuracy and parameters used to achieve an attitude rate estimation, which has a precision greater than 1 × 10-6 rad/s. The method can be applied to all attitude sensors, which use optics systems such as sun sensors and star trackers (STTs). Finally, the method is applied to the nano astrometry satellite Nano-JASMINE, and we investigate the problems that are expected to arise with real small satellites by performing numerical simulations.

40 CFR 412.10 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Horses and Sheep § 412.10 Applicability. This subpart applies to discharges resulting from the production areas at horse and sheep CAFOs. This subpart does not apply to such CAFOs with less than the following capacities: 10,000 sheep or 500 horses. ...

Normal contour error measurement on-machine and compensation method for polishing complex surface by MRF

NASA Astrophysics Data System (ADS)

Chen, Hua; Chen, Jihong; Wang, Baorui; Zheng, Yongcheng

2016-10-01

The Magnetorheological finishing (MRF) process, based on the dwell time method with the constant normal spacing for flexible polishing, would bring out the normal contour error in the fine polishing complex surface such as aspheric surface. The normal contour error would change the ribbon's shape and removal characteristics of consistency for MRF. Based on continuously scanning the normal spacing between the workpiece and the finder by the laser range finder, the novel method was put forward to measure the normal contour errors while polishing complex surface on the machining track. The normal contour errors was measured dynamically, by which the workpiece's clamping precision, multi-axis machining NC program and the dynamic performance of the MRF machine were achieved for the verification and security check of the MRF process. The unit for measuring the normal contour errors of complex surface on-machine was designed. Based on the measurement unit's results as feedback to adjust the parameters of the feed forward control and the multi-axis machining, the optimized servo control method was presented to compensate the normal contour errors. The experiment for polishing 180mm × 180mm aspherical workpiece of fused silica by MRF was set up to validate the method. The results show that the normal contour error was controlled in less than 10um. And the PV value of the polished surface accuracy was improved from 0.95λ to 0.09λ under the conditions of the same process parameters. The technology in the paper has been being applied in the PKC600-Q1 MRF machine developed by the China Academe of Engineering Physics for engineering application since 2014. It is being used in the national huge optical engineering for processing the ultra-precision optical parts.

Genomic-based-breeding tools for tropical maize improvement.

PubMed

Chakradhar, Thammineni; Hindu, Vemuri; Reddy, Palakolanu Sudhakar

2017-12-01

Maize has traditionally been the main staple diet in the Southern Asia and Sub-Saharan Africa and widely grown by millions of resource poor small scale farmers. Approximately, 35.4 million hectares are sown to tropical maize, constituting around 59% of the developing worlds. Tropical maize encounters tremendous challenges besides poor agro-climatic situations with average yields recorded <3 tones/hectare that is far less than the average of developed countries. On the contrary to poor yields, the demand for maize as food, feed, and fuel is continuously increasing in these regions. Heterosis breeding introduced in early 90 s improved maize yields significantly, but genetic gains is still a mirage, particularly for crop growing under marginal environments. Application of molecular markers has accelerated the pace of maize breeding to some extent. The availability of array of sequencing and genotyping technologies offers unrivalled service to improve precision in maize-breeding programs through modern approaches such as genomic selection, genome-wide association studies, bulk segregant analysis-based sequencing approaches, etc. Superior alleles underlying complex traits can easily be identified and introgressed efficiently using these sequence-based approaches. Integration of genomic tools and techniques with advanced genetic resources such as nested association mapping and backcross nested association mapping could certainly address the genetic issues in maize improvement programs in developing countries. Huge diversity in tropical maize and its inherent capacity for doubled haploid technology offers advantage to apply the next generation genomic tools for accelerating production in marginal environments of tropical and subtropical world. Precision in phenotyping is the key for success of any molecular-breeding approach. This article reviews genomic technologies and their application to improve agronomic traits in tropical maize breeding has been reviewed in detail.

Osmoregulation, ionoregulation and acid-base regulation by the gastrointestinal tract after feeding in the elasmobranch (Squalus acanthias).

PubMed

Wood, Chris M; Kajimura, Makiko; Bucking, Carol; Walsh, Patrick J

2007-04-01

In order to study the physiological consequences of voluntary feeding in the gastrointestinal tract of a ureotelic marine elasmobranch, dogfish (fasted for 96 h) were sampled at various times up to 360 h after consuming a 5-6% ration of teleost fish (hake) under natural feeding conditions. Digestion and absorption were completed between 120 and 360 h post-feeding. The tissue masses of different segments of the gastrointestinal tract increased and decreased markedly as the chyme moved through, mainly because of fluid engorgement rather than hyperplasia. In fasted dogfish, the cardiac and pyloric stomachs contained only small volumes of highly acidic fluid (pH 1.77+/-1.12, 2.05+/-0.08) similar in composition to seawater. Feeding resulted in gastric pHs of 3.20+/-0.31 and 3.95+/-0.40 at 6 h, followed by slow declines through 60 h. An alkaline tide in the blood also occurred at 6 h. In the face of large changing masses of highly acidic chyme in the stomachs, the pH (6.50+/-0.10), ionic composition and volume of chyme in the intestine (spiral valve) were precisely regulated from 6 to 60 h post-feeding at very different values from those in the stomachs, and intestinal HCO3(-) remained low (5.12+/-0.83 mmol l(-1)). The colon was usually empty and its pH constant at 7.20+/-0.16 at all times. Despite the ingestion of strongly hypo-osmotic teleost tissue, the osmolality of the chyme remained in equilibrium with that of the blood plasma in all segments at all times after feeding. Much of the osmotic equilibration was because of the secretion of urea into the chyme, particularly in the intestine. After feeding, gastric fluid concentrations of Na(+) and Mg(2+) declined, K(+) and Ca(2+) increased, whereas Cl(-) exhibited little change, indicating that additional drinking of seawater was minimal. Na(+), K(+), water and especially Cl(-) were absorbed in the intestine, whereas Mg(2+) and Ca(2+) were largely excluded. Our results illustrate the complex integration of digestive and ionoregulatory function in the elasmobranch digestive tract, and marked differences from the teleost pattern.

Beta-delayed proton emission from 20Mg

NASA Astrophysics Data System (ADS)

Lund, M. V.; Andreyev, A.; Borge, M. J. G.; Cederkäll, J.; De Witte, H.; Fraile, L. M.; Fynbo, H. O. U.; Greenlees, P. T.; Harkness-Brennan, L. J.; Howard, A. M.; Huyse, M.; Jonson, B.; Judson, D. S.; Kirsebom, O. S.; Konki, J.; Kurcewicz, J.; Lazarus, I.; Lica, R.; Lindberg, S.; Madurga, M.; Marginean, N.; Marginean, R.; Marroquin, I.; Mihai, C.; Munch, M.; Nacher, E.; Negret, A.; Nilsson, T.; Page, R. D.; Pascu, S.; Perea, A.; Pucknell, V.; Rahkila, P.; Rapisarda, E.; Riisager, K.; Rotaru, F.; Sotty, C.; Stanoiu, M.; Tengblad, O.; Turturica, A.; Van Duppen, P.; Vedia, V.; Wadsworth, R.; Warr, N.

2016-10-01

Beta-delayed proton emission from 20 Mg has been measured at ISOLDE, CERN, with the ISOLDE Decay Station (IDS) setup including both charged-particle and gamma-ray detection capabilities. A total of 27 delayed proton branches were measured including seven so far unobserved. An updated decay scheme, including three new resonances above the proton separation energy in 20 Na and more precise resonance energies, is presented. Beta-decay feeding to two resonances above the Isobaric Analogue State (IAS) in 20 Na is observed. This may allow studies of the 4032.9(2.4)keV resonance in 19 Ne through the beta decay of 20 Mg, which is important for the astrophysically relevant reaction 15O( α, γ)19Ne . Beta-delayed protons were used to obtain a more precise value for the half-life of 20 Mg, 91.4(1.0)ms.

Method and apparatus for measuring areas of photoelectric cells and photoelectric cell performance parameters

DOEpatents

Osterwald, C.R.; Emery, K.A.

1984-05-29

A laser scanning system for scanning the surface of photovoltaic cell in a precise, stepped raster pattern includes electric current detecting and measuring equipment for sensing the current response of the scanned cell to the laser beam at each stepped irradiated spot or pixel on the cell surface. A computer is used to control and monitor the raster position of the laser scan as well as monitoring the corresponding current responses, storing this data, operating on it, and for feeding the data to a graphical plotter for producing a visual, color-coded image of the current response of the cell to the laser scan. A translation platform driven by stepper motors in precise X and Y distances holds and rasters the cell being scanned under a stationary spot-focused laser beam.

Method and apparatus for measuring areas of photoelectric cells and photoelectric cell performance parameters

DOEpatents

Osterwald, Carl R.; Emery, Keith A.

1987-01-01

A laser scanning system for scanning the surface of a photovoltaic cell in a precise, stepped raster pattern includes electric current detecting and measuring equipment for sensing the current response of the scanned cell to the laser beam at each stepped irradiated spot or pixel on the cell surface. A computer is used to control and monitor the raster position of the laser scan as well as monitoring the corresponding current responses, storing this data, operating on it, and for feeding the data to a graphic plotter for producing a visual, color-coded image of the current response of the cell to the laser scan. A translation platform driven by stepper motors in precise X and Y distances holds and rasters the cell being scanned under a stationary spot-focused laser beam.

Research on Precision Tracking on Fast Steering Mirror and Control Strategy

NASA Astrophysics Data System (ADS)

Di, Lin; Yi-ming, Wu; Fan, Zhu

2018-01-01

Fast steering mirror is a device used for controlling the beam direction precisely. Due to the short travel of the push-pull FSM, a compound fast steering mirror system driven by both limited-angle voice coil motor and push-pull FSM together is proposed. In the compound FSM system, limited-angle voice coil motor quickly swings at wide angle, while the push-pull FSM do high frequency movement in a small range, which provides the system with the high bandwidth and long travel. In the control strategy, the method of combining feed-forward control in Kalman filtering with auto-disturbance rejection control is used to improve trajectory tracking accuracy. The simulation result shows that tracking accuracy measured by the compound method can be improved by more than 5 times than that of the conventional PID.

Early oral feeding after pancreatoduodenectomy enhances recovery without increasing morbidity

PubMed Central

Gerritsen, Arja; Wennink, Roos A W; Besselink, Marc G H; van Santvoort, Hjalmar C; Tseng, Dorine S J; Steenhagen, Elles; Borel Rinkes, Inne H M; Molenaar, I Quintus

2014-01-01

Objective The aim of this study was to evaluate whether a change in the routine feeding strategy applied after pancreatoduodenectomy (PD) from nasojejunal tube (NJT) feeding to early oral feeding improved clinical outcomes. Methods An observational cohort study was performed in 102 consecutive patients undergoing PD. In period 1 (n = 51, historical controls), the routine postoperative feeding strategy was NJT feeding. This was changed to a protocol of early oral feeding with on-demand NJT feeding in period 2 (n = 51, consecutive prospective cohort). The primary outcome was time to resumption of adequate oral intake. Results The baseline characteristics of study subjects in both periods were comparable. In period 1, 98% (n = 50) of patients received NJT feeding, whereas in period 2, 53% (n = 27) of patients did so [for delayed gastric empting (DGE) (n = 20) or preoperative malnutrition (n = 7)]. The time to resumption of adequate oral intake significantly decreased from 12 days in period 1 to 9 days in period 2 (P = 0.015), and the length of hospital stay shortened from 18 days in period 1 to 13 days in period 2 (P = 0.015). Overall, there were no differences in the incidences of complications of Clavien–Dindo Grade III or higher, DGE, pancreatic fistula, postoperative haemorrhage and mortality between the two periods. Conclusions The introduction of an early oral feeding strategy after PD reduced the time to resumption of adequate oral intake and length of hospital stay without negatively impacting postoperative morbidity. PMID:24308458

Capacity of frontline ICDS functionaries to support caregivers on infant and young child feeding (IYCF) practices in Gujarat, India.

PubMed

Chaturvedi, Anuraag; Nakkeeran, N; Doshi, Minal; Patel, Ruchi; Bhagwat, Sadhana

2014-01-01

Improved infant and young child feeding practices have the potential to improve child growth and development outcomes in India. Anganwadi Workers, the frontline government functionaries of the national nutrition supplementation programme in India, play a vital role in promoting infant and young child feeding practices in the community. The present study assessed the Anganwadi Workers' knowledge of infant and young child feeding practices, and their ability to counsel and influence caregivers regarding these practices. Eighty Anganwadi Workers from four districts of Gujarat participated in assessment centres designed to evaluate a range of competencies considered necessary for the successful promotion of infant and young child feeding practices. The results of the evaluation showed the Anganwadi Workers possessing more knowledge about infant and young child feeding practices like initiation of breastfeeding, pre-lacteal feeding and colostrum, age of introduction of complementary foods, portion size and feeding frequency than about domains which appear to have a direct bearing on practices. A huge contrast existed between the Anganwadi Workers' knowledge and their ability to apply this in formal counselling sessions with caregivers. Inability to empathetically engage with caregivers, disregard for taking the feeding history of children, poor active listening skills and inability to provide need-based advice were pervasive during counselling. In conclusion, to ensure enhanced interaction between the Anganwadi Workers and caregivers on infant and young child feeding practices, a paradigm shift in training is required, making communication processes and counselling skills central to the training.

What ticks do under your skin: two-photon intravital imaging of Ixodes scapularis feeding in the presence of the lyme disease spirochete.

PubMed

Bockenstedt, Linda K; Gonzalez, David; Mao, Jialing; Li, Ming; Belperron, Alexia A; Haberman, Ann

2014-03-01

Lyme disease, due to infection with the Ixodes-tick transmitted spirochete Borrelia burgdorferi, is the most common tick-transmitted disease in the northern hemisphere. Our understanding of the tick-pathogen-vertebrate host interactions that sustain an enzootic cycle for B. burgdorferi is incomplete. In this article, we describe a method for imaging the feeding of Ixodes scapularis nymphs in real-time using two-photon intravital microscopy and show how this technology can be applied to view the response of Lyme borrelia in the skin of an infected host to tick feeding.

Recycling of rare earth particle by mini-hydrocyclones.

PubMed

Yu, Jian-Feng; Fu, Jian; Cheng, Hao; Cui, Zhengwei

2017-03-01

Mini-hydrocyclones were applied to separate the fine rare earth particles from the suspensions. The effects of the flow rate, split ratio, and feed concentration on the total separation efficiency and grade separation efficiency were studied. The combined effects of the flow rate (1200-1600L/h), split ratio (20-60%) and concentration (0.6-1.0wt%) on the total separation efficiency in mini-hydrocyclones were investigated using a response surface methodology. The optimum operating parameters for a total separation efficiency of 92.5% were: feed flow rate=1406L/h, split ratio=20%, and feed concentration=1wt%. Copyright © 2016 Elsevier Ltd. All rights reserved.

Energetic dose: Beyond fire and flint?

USGS Publications Warehouse

Linder, G.; Rattner, B.; Cohen, J.

2000-01-01

Nutritional and bioenergetic interactions influence exposure to environmental chemicals and may affect the risk realized when wildlife are exposed in the field. Here, food-chain analysis focuses on prairie voles (Microtus ochrogaster) and the evaluation of chemical risks associated with paraquat following 10-d dietary exposures. Reproductive effects were measured in 60-d trials that followed exposures to paraquat-tainted feed: control (untainted feed); 21 mg paraquat/kg feed; 63 mg paraquat/kg feed; and feed-restricted control (untainted feed restricted to 60% baseline consumption). Reproductive success was evaluated in control and treated breeding pairs, and a preliminary bioenergetics analysis was completed in parallel to derive exposure dose. Although reproductive performance differed among groups, feed-restriction appeared to be the dominant treatment effect observed in these 10-d feeding exposure/limited reproductive trials. Exposure dose ranged from 3.70-3.76 to 9.41-11.51 mg parquat/kg BW/day at 21 and 63 mg paraquat/kg feed stock exposures, respectively. Energetic doses as ug paraquat/kcal yielded preliminary estimates of energetic costs associated with paraquat exposure, and were similar within treatments for both sexes, ranging from 4.2-5.5 and 13.1-15.0 ug paraquat/kcal for voles exposed to 21 mg/kg feed stock and 63 mg/kg feed stock, respectively. Given the increasing likelihood that environmental chemicals will be found in wildlife habitat at 'acceptable levels', the critical role that wildlife nutrition plays in evaluating ecological risks should be fully integrated into the assessment process. Tools applied to the analysis of risk must gain higher resolution than the relatively crude methods we currently bring to the process.

Phased array feed design technology for Large Aperture Microwave Radiometer (LAMR) Earth observations

NASA Technical Reports Server (NTRS)

Schuman, H. K.

1992-01-01

An assessment of the potential and limitations of phased array antennas in space-based geophysical precision radiometry is described. Mathematical models exhibiting the dependence of system and scene temperatures and system sensitivity on phased array antenna parameters and components such as phase shifters and low noise amplifiers (LNA) are developed. Emphasis is given to minimum noise temperature designs wherein the LNA's are located at the array level, one per element or subarray. Two types of combiners are considered: array lenses (space feeds) and corporate networks. The result of a survey of suitable components and devices is described. The data obtained from that survey are used in conjunction with the mathematical models to yield an assessment of effective array antenna noise temperature for representative geostationary and low Earth orbit systems. Practical methods of calibrating a space-based, phased array radiometer are briefly addressed as well.

A Low-Cost, Reliable, High-Throughput System for Rodent Behavioral Phenotyping in a Home Cage Environment

PubMed Central

Parkison, Steven A.; Carlson, Jay D.; Chaudoin, Tammy R.; Hoke, Traci A.; Schenk, A. Katrin; Goulding, Evan H.; Pérez, Lance C.; Bonasera, Stephen J.

2016-01-01

Inexpensive, high-throughput, low maintenance systems for precise temporal and spatial measurement of mouse home cage behavior (including movement, feeding, and drinking) are required to evaluate products from large scale pharmaceutical design and genetic lesion programs. These measurements are also required to interpret results from more focused behavioral assays. We describe the design and validation of a highly-scalable, reliable mouse home cage behavioral monitoring system modeled on a previously described, one-of-a-kind system [1]. Mouse position was determined by solving static equilibrium equations describing the force and torques acting on the system strain gauges; feeding events were detected by a photobeam across the food hopper, and drinking events were detected by a capacitive lick sensor. Validation studies show excellent agreement between mouse position and drinking events measured by the system compared with video-based observation – a gold standard in neuroscience. PMID:23366406

Rotary fast tool servo system and methods

DOEpatents

Montesanti, Richard C.; Trumper, David L.

2007-10-02

A high bandwidth rotary fast tool servo provides tool motion in a direction nominally parallel to the surface-normal of a workpiece at the point of contact between the cutting tool and workpiece. Three or more flexure blades having all ends fixed are used to form an axis of rotation for a swing arm that carries a cutting tool at a set radius from the axis of rotation. An actuator rotates a swing arm assembly such that a cutting tool is moved in and away from the lathe-mounted, rotating workpiece in a rapid and controlled manner in order to machine the workpiece. A pair of position sensors provides rotation and position information for a swing arm to a control system. A control system commands and coordinates motion of the fast tool servo with the motion of a spindle, rotating table, cross-feed slide, and in-feed slide of a precision lathe.

Rotary fast tool servo system and methods

DOEpatents

Montesanti, Richard C [Cambridge, MA; Trumper, David L [Plaistow, NH; Kirtley, Jr., James L.

2009-08-18

A high bandwidth rotary fast tool servo provides tool motion in a direction nominally parallel to the surface-normal of a workpiece at the point of contact between the cutting tool and workpiece. Three or more flexure blades having all ends fixed are used to form an axis of rotation for a swing arm that carries a cutting tool at a set radius from the axis of rotation. An actuator rotates a swing arm assembly such that a cutting tool is moved in and away from the lathe-mounted, rotating workpiece in a rapid and controlled manner in order to machine the workpiece. One or more position sensors provides rotation and position information for a swing arm to a control system. A control system commands and coordinates motion of the fast tool servo with the motion of a spindle, rotating table, cross-feed slide, and in-feed slide of a precision lathe.

Paleo-tribology: development of wear measurement techniques and a three-dimensional model revealing how grinding dentitions self-wear to enable functionality

NASA Astrophysics Data System (ADS)

Erickson, Gregory M.; Sidebottom, Mark A.; Curry, John F.; Kay, David Ian; Kuhn-Hendricks, Stephen; Norell, Mark A.; Sawyer, W. Gregory; Krick, Brandon A.

2016-06-01

In most mammals and a rare few reptilian lineages the evolution of precise dental occlusion led to the capacity to form functional chewing surfaces due to pressures generated while feeding. The complex dental architectures of such teeth and the biomechanics of their self-wearing nature are poorly understood. Our research team composed of paleontologists, evolutionary biologists, and engineers have developed a protocol to: (1) determine the histological make-up of grinding dentitions in extant and fossil taxa; (2) ascertain wear-relevant material properties of the tissues; (3) determine how those properties relate to inter-tissue-biomechanics leading the dental functionality using a three-dimensional Archard’s wear model developed specifically for dental applications; (4) analyze those data in phylogenetic contexts to infer evolutionary patterns as they relate to feeding. Finally we discuss industrial applications that are emerging from our paleontologically-inspired research.

Performance Guaranteed Inertia Emulation forDiesel-Wind System Feed Microgrid via ModelReference Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melin, Alexander M.; Zhang, Yichen; Djouadi, Seddik

In this paper, a model reference control based inertia emulation strategy is proposed. Desired inertia can be precisely emulated through this control strategy so that guaranteed performance is ensured. A typical frequency response model with parametrical inertia is set to be the reference model. A measurement at a specific location delivers the information of disturbance acting on the diesel-wind system to the referencemodel. The objective is for the speed of the diesel-wind system to track the reference model. Since active power variation is dominantly governed by mechanical dynamics and modes, only mechanical dynamics and states, i.e., a swing-engine-governor system plusmore » a reduced-order wind turbine generator, are involved in the feedback control design. The controller is implemented in a three-phase diesel-wind system feed microgrid. The results show exact synthetic inertia is emulated, leading to guaranteed performance and safety bounds.« less

Sub-Shot-Noise Transmission Measurement Enabled by Active Feed-Forward of Heralded Single Photons

NASA Astrophysics Data System (ADS)

Sabines-Chesterking, J.; Whittaker, R.; Joshi, S. K.; Birchall, P. M.; Moreau, P. A.; McMillan, A.; Cable, H. V.; O'Brien, J. L.; Rarity, J. G.; Matthews, J. C. F.

2017-07-01

Harnessing the unique properties of quantum mechanics offers the possibility of delivering alternative technologies that can fundamentally outperform their classical counterparts. These technologies deliver advantages only when components operate with performance beyond specific thresholds. For optical quantum metrology, the biggest challenge that impacts on performance thresholds is optical loss. Here, we demonstrate how including an optical delay and an optical switch in a feed-forward configuration with a stable and efficient correlated photon-pair source reduces the detector efficiency required to enable quantum-enhanced sensing down to the detection level of single photons and without postselection. When the switch is active, we observe a factor of improvement in precision of 1.27 for transmission measurement on a per-input-photon basis compared to the performance of a laser emitting an ideal coherent state and measured with the same detection efficiency as our setup. When the switch is inoperative, we observe no quantum advantage.

[Precision and personalized medicine].

PubMed

Sipka, Sándor

2016-10-01

The author describes the concept of "personalized medicine" and the newly introduced "precision medicine". "Precision medicine" applies the terms of "phenotype", "endotype" and "biomarker" in order to characterize more precisely the various diseases. Using "biomarkers" the homogeneous type of a disease (a "phenotype") can be divided into subgroups called "endotypes" requiring different forms of treatment and financing. The good results of "precision medicine" have become especially apparent in relation with allergic and autoimmune diseases. The application of this new way of thinking is going to be necessary in Hungary, too, in the near future for participants, controllers and financing boards of healthcare. Orv. Hetil., 2016, 157(44), 1739-1741.

Understanding Infusion Pumps.

PubMed

Mandel, Jeff E

2018-04-01

Infusion systems are complicated electromechanical systems that are used to deliver anesthetic drugs with moderate precision. Four types of systems are described-gravity feed, in-line piston, peristaltic, and syringe. These systems are subject to a number of failure modes-occlusion, disconnection, siphoning, infiltration, and air bubbles. The relative advantages of the various systems and some of the monitoring capabilities are discussed. A brief example of the use of an infusion system during anesthetic induction is presented. With understanding of the functioning of these systems, users may develop greater comfort.

ATS-6 engineering performance report. Volume 2: Orbit and attitude controls

NASA Technical Reports Server (NTRS)

Wales, R. O. (Editor)

1981-01-01

Attitude control is reviewed, encompassing the attitude control subsystem, spacecraft attitude precision pointing and slewing adaptive control experiment, and RF interferometer experiment. The spacecraft propulsion system (SPS) is discussed, including subsystem, SPS design description and validation, orbital operations and performance, in-orbit anomalies and contingency operations, and the cesium bombardment ion engine experiment. Thruster failure due to plugging of the propellant feed passages, a major cause for mission termination, are considered among the critical generic failures on the satellite.

Quantitation of fumonisin B1 and B2 in feed using FMOC pre-column derivatization with HPLC and fluorescence detection.

PubMed

Smith, Lori L; Francis, Kyle A; Johnson, Joseph T; Gaskill, Cynthia L

2017-11-01

Pre-column derivatization with 9-fluorenylmethyl chloroformate (FMOC-Cl) was determined to be effective for quantitation of fumonisins B 1 and B 2 in feed. Liquid-solid extraction, clean-up using immunoaffinity solid phase extraction chromatography, and FMOC-derivatization preceded analysis by reverse phase HPLC with fluorescence. Instrument response was unchanged in the presence of matrix, indicating no need to use matrix-matched calibrants. Furthermore, high method recoveries indicated calibrants do not need to undergo clean-up to account for analyte loss. Established method features include linear instrument response from 0.04-2.5µg/mL and stable derivatized calibrants over 7days. Fortified cornmeal method recoveries from 0.1-30.0μg/g were determined for FB 1 (75.1%-109%) and FB 2 (96.0%-115.2%). Inter-assay precision ranged from 1.0%-16.7%. Method accuracy was further confirmed using certified reference material. Inter-laboratory comparison with naturally-contaminated field corn demonstrated equivalent results with conventional derivatization. These results indicate FMOC derivatization is a suitable alternative for fumonisins B 1 and B 2 quantitation in corn-based feeds. Copyright © 2017 Elsevier Ltd. All rights reserved.

Review: Quantifying animal feeding behaviour with a focus on pigs.

PubMed

Maselyne, Jarissa; Saeys, Wouter; Van Nuffel, Annelies

2015-01-01

The study of animal feeding behaviour is of interest to understand feeding, to investigate the effect of treatments and conditions or to predict illness. This paper reviews the different steps to undertake when studying animal feeding behaviour, with illustrations for group-housed pigs. First, one must be aware of the mechanisms that control feeding and the various influences that can change feeding behaviour. Satiety is shown to largely influence free feeding (ad libitum and without an operant condition) in animals, but 'free' feeding seems a very fragile process, given the many factors that can influence feeding behaviour. Second, a measurement method must be chosen that is compatible with the goal of the research. Several measurement methods exist, which lead to different experimental set-ups and measurement data. Sensors are available for lab conditions, for research on group-housed pigs and also for on-farm use. Most of these methods result in a record of feeding visits. However, these feeding visits are often found to be clustered into meals. Thus, the third step is to choose which unit of feeding behaviour to use for analysis. Depending on the situation, either meals, feeding visits, other raw data, or a combination thereof can be suitable. Meals are more appropriate for analysing short-term feeding behaviour, but this may not be true for disease detection. Further research is therefore needed. To cluster visits into meals, an appropriate analysis method has to be selected. The last part of this paper provides a review and discussion of the existing methods for meal determination. A variety of methods exist, with the most recent methods based on the influence of satiety on feeding. More thorough validation of the recent methods, including validation from a behavioural point of view and uniformity in the applied methods is therefore necessary. Copyright © 2014 Elsevier Inc. All rights reserved.

Process for forming coal compacts and product thereof

DOEpatents

Gunnink, Brett; Kanunar, Jayanth; Liang, Zhuoxiong

2002-01-01

A process for forming durable, mechanically strong compacts from coal particulates without use of a binder is disclosed. The process involves applying a compressive stress to a particulate feed comprising substantially water-saturated coal particles while the feed is heated to a final compaction temperature in excess of about 100.degree. C. The water present in the feed remains substantially in the liquid phase throughout the compact forming process. This is achieved by heating and compressing the particulate feed and cooling the formed compact at a pressure sufficient to prevent water present in the feed from boiling. The compacts produced by the process have a moisture content near their water saturation point. As a result, these compacts absorb little water and retain exceptional mechanical strength when immersed in high pressure water. The process can be used to form large, cylindrically-shaped compacts from coal particles (i.e., "coal logs") so that the coal can be transported in a hydraulic coal log pipeline.

Established enteral nutrition pathway in a severe acute pancreatitis patient with duodenum fistula: a case report.

PubMed

Li, G; Shen, X; Ke, L; Tong, Z; Li, W

2015-10-01

Enteral feeding is the preferred way to provide nutritional support in patients with high nutritional risk but relatively normal gastrointestinal function; thus, establishing a safe and a reliable pathway of enteral nutrition (EN) is of great importance. There are many techniques for placing the feeding tube, such as blind placement at bedside, assisting by fluoroscopy and endoscopy, surgical and so on. Despite these variable techniques, it is still difficult to obtain the pathway for EN in some specific patients. Here, we present a recent case of infected pancreatic/peripancreatic necrosis complicated by a duodenal enteric fistula in whom we establish the feeding pathway extraordinarily. Briefly, after several failed attempts of placing the nasojejunal feeding tube, a jejunal feeding tube was placed percutaneously guided by computed tomography, and EN was successfully applied thereafter. With the implementation of EN, duodenal fistula healed without surgical intervention. As EN is pivotal for the recovery of duodenal fistula, this novel approach could be beneficial in selected patients.

Impact of carbon and nitrogen feeding strategy on high production of biomass and docosahexaenoic acid (DHA) by Schizochytrium sp. LU310.

PubMed

Ling, Xueping; Guo, Jing; Liu, Xiaoting; Zhang, Xia; Wang, Nan; Lu, Yinghua; Ng, I-Son

2015-05-01

A new isolated Schizochytrium sp. LU310 from the mangrove forest of Wenzhou, China, was found as a high producing microalga of docosahexaenoic acid (DHA). In this study, the significant improvements for DHA fermentation by the batch mode in the baffled flasks (i.e. higher oxygen supply) were achieved. By applied the nitrogen-feeding strategy in 1000 mL baffled flasks, the biomass, DHA concentration and DHA productivity were increased by 110.4%, 117.9% and 110.4%, respectively. Moreover, DHA concentration of 21.06 g/L was obtained by feeding 15 g/L of glucose intermittently, which was an increase of 41.25% over that of the batch mode. Finally, an innovative strategy was carried out by intermittent feeding carbon and simultaneously feeding nitrogen. The maximum DHA concentration and DHA productivity in the fed-batch cultivation reached to 24.74 g/L and 241.5 mg/L/h, respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fast and simultaneous prediction of animal feed nutritive values using near infrared reflectance spectroscopy

NASA Astrophysics Data System (ADS)

Samadi; Wajizah, S.; Munawar, A. A.

2018-02-01

Feed plays an important factor in animal production. The purpose of this study is to apply NIRS method in determining feed values. NIRS spectra data were acquired for feed samples in wavelength range of 1000 - 2500 nm with 32 scans and 0.2 nm wavelength. Spectral data were corrected by de-trending (DT) and standard normal variate (SNV) methods. Prediction of in vitro dry matter digestibility (IVDMD) and in vitro organic matter digestibility (IVOMD) were established as model by using principal component regression (PCR) and validated using leave one out cross validation (LOOCV). Prediction performance was quantified using coefficient correlation (r) and residual predictive deviation (RPD) index. The results showed that IVDMD and IVOMD can be predicted by using SNV spectra data with r and RPD index: 0.93 and 2.78 for IVDMD ; 0.90 and 2.35 for IVOMD respectively. In conclusion, NIRS technique appears feasible to predict animal feed nutritive values.

Central composite rotatable design for investigation of microwave-assisted extraction of ginger (Zingiber officinale)

NASA Astrophysics Data System (ADS)

Fadzilah, R. Hanum; Sobhana, B. Arianto; Mahfud, M.

2015-12-01

Microwave-assisted extraction technique was employed to extract essential oil from ginger. The optimal condition for microwave assisted extraction of ginger were determined by resposnse surface methodology. A central composite rotatable design was applied to evaluate the effects of three independent variables. The variables is were microwave power 400 - 800W as X1, feed solvent ratio of 0.33 -0.467 as X2 and feed size 1 cm, 0.25 cm and less than 0.2 cm as X3. The correlation analysis of mathematical modelling indicated that quadratic polynomial could be employed to optimize microwave assisted extraction of ginger. The optimal conditions to obtain highest yield of essential oil were : microwave power 597,163 W : feed solvent ratio and size of feed less than 0.2 cm.

Study on the cutting mechanism and the brittle ductile transition model of isotropic pyrolyric graphite

NASA Astrophysics Data System (ADS)

Wang, Minghai; Wang, Hujun; Liu, Zhonghai

2011-05-01

Isotropic pyrolyric graphite (IPG) is a new kind of brittle material, it can be used for sealing the aero-engine turbine shaft and the ethylene high-temperature equipment. It not only has the general advantages of ordinal carbonaceous materials such as high temperature resistance, lubrication and abrasion resistance, but also has the advantages of impermeability and machinability that carbon/carbon composite doesn't have. Therefore, it has broad prospects for development. Mechanism of brittle-ductile transition of IPG is the foundation of precision cutting while the plastic deformation of IPG is the essential and the most important mechanical behavior of precision cutting. Using the theory of strain gradient, the mechanism of this material removal during the precision cutting is analyzed. The critical cutting thickness of IPG is calculated for the first time. Furthermore, the cutting process parameters such as cutting depth, feed rate which corresponding to the scale of brittle-ductile transition deformation of IPG are calculated. In the end, based on the theory of micromechanics, the deformation behaviors of IPG such as brittle fracture, plastic deformation and mutual transformation process are all simulated under the Sih.G.C fracture criterion. The condition of the simulation is that the material under the pressure-shear loading conditions .The result shows that the best angle during the IPG precision cutting is -30°. The theoretical analysis and the simulation result are validated by precision cutting experiments.

Single Mode, Extreme Precision Doppler Spectrographs

NASA Astrophysics Data System (ADS)

Schwab, Christian; Leon-Saval, Sergio G.; Betters, Christopher H.; Bland-Hawthorn, Joss; Mahadevan, Suvrath

2014-04-01

The `holy grail' of exoplanet research today is the detection of an earth-like planet: a rocky planet in the habitable zone around a main-sequence star. Extremely precise Doppler spectroscopy is an indispensable tool to find and characterize earth-like planets; however, to find these planets around solar-type stars, we need nearly one order of magnitude better radial velocity (RV) precision than the best current spectrographs provide. Recent developments in astrophotonics (Bland-Hawthorn & Horton 2006, Bland-Hawthorn et al. 2010) and adaptive optics (AO) enable single mode fiber (SMF) fed, high resolution spectrographs, which can realize the next step in precision. SMF feeds have intrinsic advantages over multimode fiber or slit coupled spectrographs: The intensity distribution at the fiber exit is extremely stable, and as a result the line spread function of a well-designed spectrograph is fully decoupled from input coupling conditions, like guiding or seeing variations (Ihle et al. 2010). Modal noise, a limiting factor in current multimode fiber fed instruments (Baudrand & Walker 2001), can be eliminated by proper design, and the diffraction limited input to the spectrograph allows for very compact instrument designs, which provide excellent optomechanical stability. A SMF is the ideal interface for new, very precise wavelength calibrators, like laser frequency combs (Steinmetz et al. 2008, Osterman et al. 2012), or SMF based Fabry-Perot Etalons (Halverson et al. 2013). At near infrared wavelengths, these technologies are ready to be implemented in on-sky instruments, or already in use. We discuss a novel concept for such a spectrograph.

Ultrananocrystalline Diamond Cantilever Wide Dynamic Range Acceleration/Vibration /Pressure Sensor

DOEpatents

Krauss, Alan R.; Gruen, Dieter M.; Pellin, Michael J.; Auciello, Orlando

2003-09-02

An ultrananocrystalline diamond (UNCD) element formed in a cantilever configuration is used in a highly sensitive, ultra-small sensor for measuring acceleration, shock, vibration and static pressure over a wide dynamic range. The cantilever UNCD element may be used in combination with a single anode, with measurements made either optically or by capacitance. In another embodiment, the cantilever UNCD element is disposed between two anodes, with DC voltages applied to the two anodes. With a small AC modulated voltage applied to the UNCD cantilever element and because of the symmetry of the applied voltage and the anode-cathode gap distance in the Fowler-Nordheim equation, any change in the anode voltage ratio V1/V2 required to maintain a specified current ratio precisely matches any displacement of the UNCD cantilever element from equilibrium. By measuring changes in the anode voltage ratio required to maintain a specified current ratio, the deflection of the UNCD cantilever can be precisely determined. By appropriately modulating the voltages applied between the UNCD cantilever and the two anodes, or limit electrodes, precise independent measurements of pressure, uniaxial acceleration, vibration and shock can be made. This invention also contemplates a method for fabricating the cantilever UNCD structure for the sensor.

Ultrananocrystalline diamond cantilever wide dynamic range acceleration/vibration/pressure sensor

DOEpatents

Krauss, Alan R [Naperville, IL; Gruen, Dieter M [Downers Grove, IL; Pellin, Michael J [Naperville, IL; Auciello, Orlando [Bolingbrook, IL

2002-07-23

An ultrananocrystalline diamond (UNCD) element formed in a cantilever configuration is used in a highly sensitive, ultra-small sensor for measuring acceleration, shock, vibration and static pressure over a wide dynamic range. The cantilever UNCD element may be used in combination with a single anode, with measurements made either optically or by capacitance. In another embodiment, the cantilever UNCD element is disposed between two anodes, with DC voltages applied to the two anodes. With a small AC modulated voltage applied to the UNCD cantilever element and because of the symmetry of the applied voltage and the anode-cathode gap distance in the Fowler-Nordheim equation, any change in the anode voltage ratio V1/N2 required to maintain a specified current ratio precisely matches any displacement of the UNCD cantilever element from equilibrium. By measuring changes in the anode voltage ratio required to maintain a specified current ratio, the deflection of the UNCD cantilever can be precisely determined. By appropriately modulating the voltages applied between the UNCD cantilever and the two anodes, or limit electrodes, precise independent measurements of pressure, uniaxial acceleration, vibration and shock can be made. This invention also contemplates a method for fabricating the cantilever UNCD structure for the sensor.

The better to eat you with: the comparative feeding morphology of phocid seals (Pinnipedia, Phocidae).

PubMed

Kienle, Sarah S; Berta, Annalisa

2016-03-01

One adaptation crucial to the survival of mammalian lineages that secondarily transitioned from land to water environments was the ability to capture and consume prey underwater. Phocid seals have evolved diverse feeding strategies to feed in the marine environment, and the objectives of this study were to document the specialized feeding morphologies and identify feeding strategies used by extant phocids. This study used principal component analysis (PCA) to determine the major axes of diversification in the skull for all extant phocid taxa and the recently extinct Caribbean monk seal (n = 19). Prey data gathered from the literature and musculoskeletal data from dissections were included to provide a comprehensive description of each feeding strategy. Random Forest analysis was used to determine the morphological, ecological and phylogenetic variables that best described each feeding strategy. There is morphological evidence for four feeding strategies in phocids: filter; grip and tear; suction; and pierce feeding. These feeding strategies are supported by quantitative cranial and mandibular characters, dietary information, musculoskeletal data and, for some species, behavioral observations. Most phocid species are pierce feeders, using a combination of biting and suction to opportunistically catch prey. Grip and tear and filter feeding are specialized strategies with specific morphological adaptations. These unique adaptations have allowed leopard seals (Hydrurga leptonyx) and crabeater seals (Lobodon carcinophaga) to exploit novel ecological niches and prey types. This study provides the first cranial and mandibular morphological evidence for the use of specialized suction feeding in hooded seals (Cystophora cristata), northern elephant seals (Mirounga angustirostris) and southern elephant seals (Mirounga leonina). The most important variables in determining the feeding strategy of a given phocid species were cranial and mandibular shape, diet, and phylogeny. These results provide a framework for understanding the evolution and adaptability of feeding strategies employed by extant phocid species, and these findings can be applied to other pinniped lineages and extinct taxa. © 2015 Anatomical Society.

Effect of methionine and lactic acid bacteria as aflatoxin binder on broiler performance

NASA Astrophysics Data System (ADS)

Istiqomah, Lusty; Damayanti, Ema; Julendra, Hardi; Suryani, Ade Erma; Sakti, Awistaros Angger; Anggraeni, Ayu Septi

2017-06-01

The use of aflatoxin binder product based amino acids, lacic acid bacteria, and natural product gived the opportunity to be an alternative biological decontamination of aflatoxins. A study was conducted to determine the efficacy of aflatoxin binder administration (amino acid methionine and lactic acid bacteria (Lactobacillus plantarum G7)) as feed additive on broiler performance. In this study, 75 Lohmann unsexed day old chicks were distributed randomly into 5 units of cages, each filled with 15 broilers. Five cages were assigned into 5 treatments groups and fed with feed contained aflatoxin. The treatments as follow: P1 (aflatoxin feed without aflatoxin binder), P3 (aflatoxin feed + 0.8% of methionine + 1% of LAB), P4 (aflatoxin feed + 1.2% of methionine + 1% of LAB), P5 (aflatoxin feed + 1% of LAB), and K0 (commercial feed). The measurement of aflatoxin content in feed was performed by Enzyme Linked Immunosorbent Assay method using AgraQuant® Total Aflatoxin Assay Romer Labs procedure. The experimental period was 35 days with feeding and drinking ad libitum. LAB was administered into drinking water, while methionine into feed. Vaccination program of Newcastle Disease (ND) was using active vaccine at 4 and 18 day old, while Infectious Bursal Disease (IBD) was given at 8 day old. Parameter of body weight was observed weekly, while feed consumption noted daily. The result showed that aflatoxin in feed for 35 days period did not significantly affect the body weight gain and feed conversion. The lowest percentage of organ damage at 21 day old was found in P5 treatment (55%), while at 35day old was found in P4 treatment (64%). It could be concluded that technological process of detoxifying aflatoxin could be applied in an attempt to reduce the effect on the toxicity of aflatoxin in poultry feed.

Localising livestock protein feed production and the impact on land use and greenhouse gas emissions.

PubMed

Sasu-Boakye, Y; Cederberg, C; Wirsenius, S

2014-08-01

Livestock farmers in Sweden usually grow feed grains for livestock but import protein feed from outside Sweden. Aside from the economic implications, some environmental issues are associated with this practice. We used life cycle assessment to evaluate the impact of local protein feed production on land use and greenhouse gas emissions, compared with the use of imported protein feed, for pig meat and dairy milk produced in Sweden. Our results showed that local production reduced greenhouse gas emissions by 4.5% and 12%, respectively, for pigs and dairy cows. Land use for feed production in Sweden increased by 11% for pigs and 25% for dairy cows, but total land use decreased for pig production and increased for dairy milk production. Increased protein feed cultivation in Sweden decreased inputs needed for animal production and improved some ecological processes (e.g. nutrient recycling) of the farm systems. However, the differences in results between scenarios are relatively small and influenced to an extent by methodological choices such as co-product allocation. Moreover, it was difficult to assess the contribution of greenhouse emissions from land use change. The available accounting methods we applied did not adequately account for the potential land use changes and in some cases provided conflicting results. We conclude that local protein feed production presents an opportunity to reduce greenhouse gas emissions but at a cost of increasing land occupation in Sweden for feed production.

Feeding behaviour in a 'basal' tortoise provides insights on the transitional feeding mode at the dawn of modern land turtle evolution.

PubMed

Natchev, Nikolay; Tzankov, Nikolay; Werneburg, Ingmar; Heiss, Egon

2015-01-01

Almost all extant testudinids are highly associated with terrestrial habitats and the few tortoises with high affinity to aquatic environments are found within the genus Manouria. Manouria belongs to a clade which forms a sister taxon to all remaining tortoises and is suitable as a model for studying evolutionary transitions within modern turtles. We analysed the feeding behaviour of Manouria emys and due to its phylogenetic position, we hypothesise that the species might have retained some ancestral features associated with an aquatic lifestyle. We tested whether M. emys is able to feed both in aquatic and terrestrial environments. In fact, M. emys repetitively tried to reach submerged food items in water, but always failed to grasp them-no suction feeding mechanism was applied. When feeding on land, M. emys showed another peculiar behaviour; it grasped food items by its jaws-a behaviour typical for aquatic or semiaquatic turtles-and not by the tongue as generally accepted as the typical feeding mode in all tortoises studied so far. In M. emys, the hyolingual complex remained retracted during all food uptake sequences, but the food transport was entirely lingual based. The kinematical profiles significantly differed from those described for other tortoises and from those proposed from the general models on the function of the feeding systems in lower tetrapods. We conclude that the feeding behaviour of M. emys might reflect a remnant of the primordial condition expected in the aquatic ancestor of the tortoises.

Strain-specific antibodies reduce co-feeding transmission of the Lyme disease pathogen, Borrelia afzelii.

PubMed

Jacquet, Maxime; Durand, Jonas; Rais, Olivier; Voordouw, Maarten J

2016-03-01

Vector-borne pathogens use a diversity of strategies to evade the vertebrate immune system. Co-feeding transmission is a potential immune evasion strategy because the vector-borne pathogen minimizes the time spent in the vertebrate host. We tested whether the Lyme disease pathogen, Borrelia afzelii, can use co-feeding transmission to escape the acquired immune response in the vertebrate host. We induced a strain-specific, protective antibody response by immunizing mice with one of two variants of OspC (A3 and A10), the highly variable outer surface protein C of Borrelia pathogens. Immunized mice were challenged via tick bite with B. afzelii strains A3 or A10 and infested with larval ticks at days 2 and 34 post-infection to measure co-feeding and systemic transmission respectively. Antibodies against a particular OspC variant significantly reduced co-feeding transmission of the targeted (homologous) strain but not the non-targeted (heterologous) strain. Cross-immunity between OspC antigens had no effect in co-feeding ticks but reduced the spirochaete load twofold in ticks infected via systemic transmission. In summary, OspC-specific antibodies reduced co-feeding transmission of a homologous but not a heterologous strain of B. afzelii. Co-feeding transmission allowed B. afzelii to evade the negative consequences of cross-immunity on the tick spirochaete load. © 2015 Society for Applied Microbiology and John Wiley & Sons Ltd.

Effect of prolonged breast-feeding on risk of atopic dermatitis in early childhood.

PubMed

Hong, Soyoung; Choi, Won-Jun; Kwon, Ho-Jang; Cho, Yoon Hee; Yum, Hye Yung; Son, Dong Koog

2014-01-01

The effect of breast-feeding on the risk of developing atopic disease remains controversial. This study is an investigation of the effect of breast-feeding on current atopic dermatitis (AD) among Korean children. This cross-sectional study of children's histories of current AD and environmental factors was completed by the subjects' parents. The subjects included 10,383 children aged 0-13 years in Seoul, Korea, in 2008. The diagnostic criteria of the International Study of Asthma and Allergies in Childhood were applied in this study. Adjustments were performed for age, gender, maternal education, smoking in the household, relocation to a new house within 1 year of birth, and parental history of atopic disease. After adjustment for confounders, age and duration of maternal education were found to be inversely associated with the prevalence of AD. Among subjects aged ≤5 years, the prevalence of AD was positively associated with the duration of breast-feeding (p < 0.001). However, there was no significant association between AD and breast-feeding among children >5 years of age. Regardless of parental history of atopic diseases, breast-feeding >12 months was a significant risk factor for AD. The effect of breast-feeding differed by age group. Prolonged breast-feeding increased the risk of AD in children <5 years of age, regardless of parental history of atopic diseases.

Comparative study on gastrointestinal microbiota of eight fish species with different feeding habits.

PubMed

Li, J; Ni, J; Li, J; Wang, C; Li, X; Wu, S; Zhang, T; Yu, Y; Yan, Q

2014-12-01

To reveal the effects of fish genotype, feeding habits and serum physiological index on the composition of gastrointestinal microbiota, eight fish species with four different feeding habits were investigated. The V1 to V3 regions of 16S rRNA gene were analysed by high-throughput sequencing (454 platform) to compare the gut microbiota of different fish species. A total of 551 995 high-quality sequences with an average length of 463 bp were obtained from the 48 samples. No significant difference was observed among the detected sequences obtained from fishes with different feeding habits (One-way anova, F = 1·003, P = 0·400), but the number of OTUs among different feeding habits was significantly different (One-way anova, F = 7·564, P < 0·001). Additionally, significant correlations were detected between the fish genotype and microbial composition (partial Mantel test, all P values = 0·001) in the stomach, foregut and hindgut. Moreover, different core intestinal microbiota was also noticed in the eight fish species with different feeding habits. Feeding habits and genotype clearly affected the gastrointestinal microbiota of fish. Moreover, the evolutionary process shaped the serum physiological indexes of fish. This study provided much important information for developing commercial fish feeds. © 2014 The Society for Applied Microbiology.

Use of precision time and time interval (PTTI)

NASA Technical Reports Server (NTRS)

Taylor, J. D.

1974-01-01

A review of range time synchronization methods are discussed as an important aspect of range operations. The overall capabilities of various missile ranges to determine precise time of day by synchronizing to available references and applying this time point to instrumentation for time interval measurements are described.

A comparison of precision mobile drip irrigation, LESA and LEPA

USDA-ARS?s Scientific Manuscript database

Precision mobile drip irrigation (PMDI) is a surface drip irrigation system fitted onto moving sprinkler systems that applies water through the driplines as they are dragged across the field. This application method can conserve water by limiting runoff, and reducing evaporative losses since the wat...

The feeding tube of cyst nematodes: characterisation of protein exclusion.

PubMed

Eves-van den Akker, Sebastian; Lilley, Catherine J; Ault, James R; Ashcroft, Alison E; Jones, John T; Urwin, Peter E

2014-01-01

Plant parasitic nematodes comprise several groups; the most economically damaging of these are the sedentary endoparasites. Sedentary endoparasitic nematodes are obligate biotrophs and modify host root tissue, using a suite of effector proteins, to create a feeding site that is their sole source of nutrition. They feed by withdrawing host cell assimilate from the feeding site though a structure known as the feeding tube. The function, composition and molecular characteristics of feeding tubes are poorly characterised. It is hypothesised that the feeding tube facilitates uptake of host cell assimilate by acting as a molecular sieve. Several studies, using molecular mass as the sole indicator of protein size, have given contradictory results about the exclusion limits of the cyst nematode feeding tube. In this study we propose a method to predict protein size, based on protein database coordinates in silico. We tested the validity of these predictions using travelling wave ion mobility spectrometry--mass spectrometry, where predictions and measured values were within approximately 6%. We used the predictions, coupled with mass spectrometry, analytical ultracentrifugation and protein electrophoresis, to resolve previous conflicts and define the exclusion characteristics of the cyst nematode feeding tube. Heterogeneity was tested in the liquid, solid and gas phase to provide a comprehensive evaluation of three proteins of particular interest to feeding tube size exclusion, GFP, mRFP and Dual PI. The data and procedures described here could be applied to the design of plant expressed defence compounds intended for uptake into cyst nematodes. We also highlight the need to assess protein heterogeneity when creating novel fusion proteins.

Routing of Fatty Acids from Fresh Grass to Milk Restricts the Validation of Feeding Information Obtained by Measuring (13)C in Milk.

PubMed

Auerswald, Karl; Schäufele, Rudi; Bellof, Gerhard

2015-12-09

Dairy production systems vary widely in their feeding and livestock-keeping regimens. Both are well-known to affect milk quality and consumer perceptions. Stable isotope analysis has been suggested as an easy-to-apply tool to validate a claimed feeding regimen. Although it is unambiguous that feeding influences the carbon isotope composition (δ(13)C) in milk, it is not clear whether a reported feeding regimen can be verified by measuring δ(13)C in milk without sampling and analyzing the feed. We obtained 671 milk samples from 40 farms distributed over Central Europe to measure δ(13)C and fatty acid composition. Feeding protocols by the farmers in combination with a model based on δ(13)C feed values from the literature were used to predict δ(13)C in feed and subsequently in milk. The model considered dietary contributions of C3 and C4 plants, contribution of concentrates, altitude, seasonal variation in (12/13)CO2, Suess's effect, and diet-milk discrimination. Predicted and measured δ(13)C in milk correlated closely (r(2) = 0.93). Analyzing milk for δ(13)C allowed validation of a reported C4 component with an error of <8% in 95% of all cases. This included the error of the method (measurement and prediction) and the error of the feeding information. However, the error was not random but varied seasonally and correlated with the seasonal variation in long-chain fatty acids. This indicated a bypass of long-chain fatty acids from fresh grass to milk.

The Feeding Tube of Cyst Nematodes: Characterisation of Protein Exclusion

PubMed Central

Eves-van den Akker, Sebastian; Lilley, Catherine J.; Ault, James R.; Ashcroft, Alison E.; Jones, John T.; Urwin, Peter E.

2014-01-01

Plant parasitic nematodes comprise several groups; the most economically damaging of these are the sedentary endoparasites. Sedentary endoparasitic nematodes are obligate biotrophs and modify host root tissue, using a suite of effector proteins, to create a feeding site that is their sole source of nutrition. They feed by withdrawing host cell assimilate from the feeding site though a structure known as the feeding tube. The function, composition and molecular characteristics of feeding tubes are poorly characterised. It is hypothesised that the feeding tube facilitates uptake of host cell assimilate by acting as a molecular sieve. Several studies, using molecular mass as the sole indicator of protein size, have given contradictory results about the exclusion limits of the cyst nematode feeding tube. In this study we propose a method to predict protein size, based on protein database coordinates in silico. We tested the validity of these predictions using travelling wave ion mobility spectrometry – mass spectrometry, where predictions and measured values were within approximately 6%. We used the predictions, coupled with mass spectrometry, analytical ultracentrifugation and protein electrophoresis, to resolve previous conflicts and define the exclusion characteristics of the cyst nematode feeding tube. Heterogeneity was tested in the liquid, solid and gas phase to provide a comprehensive evaluation of three proteins of particular interest to feeding tube size exclusion, GFP, mRFP and Dual PI. The data and procedures described here could be applied to the design of plant expressed defence compounds intended for uptake into cyst nematodes. We also highlight the need to assess protein heterogeneity when creating novel fusion proteins. PMID:24489891

Design and Validation of In-Source Atmospheric Pressure Photoionization Hydrogen/Deuterium Exchange Mass Spectrometry with Continuous Feeding of D2O.

PubMed

Acter, Thamina; Lee, Seulgidaun; Cho, Eunji; Jung, Maeng-Joon; Kim, Sunghwan

2018-01-01

In this study, continuous in-source hydrogen/deuterium exchange (HDX) atmospheric pressure photoionization (APPI) mass spectrometry (MS) with continuous feeding of D 2 O was developed and validated. D 2 O was continuously fed using a capillary line placed on the center of a metal plate positioned between the UV lamp and nebulizer. The proposed system overcomes the limitations of previously reported APPI HDX-MS approaches where deuterated solvents were premixed with sample solutions before ionization. This is particularly important for APPI because solvent composition can greatly influence ionization efficiency as well as the solubility of analytes. The experimental parameters for APPI HDX-MS with continuous feeding of D 2 O were optimized, and the optimized conditions were applied for the analysis of nitrogen-, oxygen-, and sulfur-containing compounds. The developed method was also applied for the analysis of the polar fraction of a petroleum sample. Thus, the data presented in this study clearly show that the proposed HDX approach can serve as an effective analytical tool for the structural analysis of complex mixtures. Graphical abstract ᅟ.

High efficiency cell-recycle continuous sodium gluconate production by Aspergillus niger using on-line physiological parameters association analysis to regulate feed rate rationally.

PubMed

Lu, Fei; Li, Chao; Wang, Zejian; Zhao, Wei; Chu, Ju; Zhuang, Yingping; Zhang, Siliang

2016-11-01

In this paper, a system of cell-recycle continuous fermentation for sodium gluconate (SG) production by Aspergillus niger (A. niger) was established. Based on initial continuous fermentation result (100.0h) with constant feed rate, an automatic feedback strategy to regulate feed rate using on-line physiological parameters (OUR and DO) was proposed and applied successfully for the first time in the improved continuous fermentation (240.5h). Due to less auxiliary time, highest SG production rate (31.05±0.29gL(-1)h(-1)) and highest yield (0.984±0.067molmol(-1)), overall SG production capacity (975.8±5.8gh(-1)) in 50-L fermentor of improved continuous fermentation increased more than 300.0% compared to that of batch fermentation. Improvement of mass transfer and dispersed mycelia morphology were the two major reasons responsible for the high SG production rate. This system had been successfully applied to industrial fermentation and SG production was greatly improved. Copyright © 2016 Elsevier Ltd. All rights reserved.

Molecular diversity of lactic acid bacteria on ileum broiler chicken fed by bran and bran fermentation

NASA Astrophysics Data System (ADS)

Baniyah, Laelatul; Nur Jannah, Siti; Rukmi, Isworo; Sugiharto

2018-05-01

Lactic Acid Bacteria (LAB) is a digestive tract microflora that have a positive role in poultry health. The number and diversity of LAB in the digestive tract affected by several factors, among them was the kind of feed. The purpose of this research was to know diversity of Lactic Acid Bacteria (LAB) ileum broiler’s after feeding with prebiotic bran and Rhizopus oryzae fermented bran which was added to commercial feed. As much as 15 broilers were used to determine the diversity of LAB. All broilers were fed using commercial feed. The control used commercial feed no addition of bran or fermented bran, and commercial feed with fermented bran and nonfermented bran were as a treatment. To determine the diversity of LAB, T-RFLP method was applied. The Hae III and Msp I were used as restriction enzymes. The number of phylotype, relative abundance, Shannon diversity index (H '), evenness (E), and Dominance (D) were examined. The results indicated that the addition of prebiotic bran on commercial feed showed a higher diversity of lactic acid bacteria on broiler’s ileum, compared with control and addition of Rhizopus oryzae fermented bran. LAB group that dominates in the ileum is Lactobacillus sp. and L. delbruecii subs bulgaricus.

Radiocarbon as a Novel Tracer of Extra-Antarctic Feeding in Southern Hemisphere Humpback Whales.

PubMed

Eisenmann, Pascale; Fry, Brian; Mazumder, Debashish; Jacobsen, Geraldine; Holyoake, Carlysle Sian; Coughran, Douglas; Bengtson Nash, Susan

2017-06-29

Bulk stable isotope analysis provides information regarding food web interactions, and has been applied to several cetacean species for the study of migration ecology. One limitation in bulk stable isotope analysis arises when a species, such as Southern hemisphere humpback whales, utilises geographically distinct food webs with differing isotopic baselines. Migrations to areas with different baselines can result in isotopic changes that mimic changes in feeding relations, leading to ambiguous food web interpretations. Here, we demonstrate the novel application of radiocarbon measurement for the resolution of such ambiguities. Radiocarbon was measured in baleen plates from humpback whales stranded in Australia between 2007 and 2013, and in skin samples collected in Australia and Antarctica from stranded and free-ranging animals. Radiocarbon measurements showed lower values for Southern Ocean feeding than for extra-Antarctic feeding in Australian waters. While the whales mostly relied on Antarctic-derived energy stores during their annual migration, there was some evidence of feeding within temperate zone waters in some individuals. This work, to our knowledge, provides the first definitive biochemical evidence for supplementary feeding by southern hemisphere humpback whales within temperate waters during migration. Further, the work contributes a powerful new tool (radiocarbon) for tracing source regions and geographical feeding.

Technical options for the mitigation of direct methane and nitrous oxide emissions from livestock: a review.

PubMed

Gerber, P J; Hristov, A N; Henderson, B; Makkar, H; Oh, J; Lee, C; Meinen, R; Montes, F; Ott, T; Firkins, J; Rotz, A; Dell, C; Adesogan, A T; Yang, W Z; Tricarico, J M; Kebreab, E; Waghorn, G; Dijkstra, J; Oosting, S

2013-06-01

Although livestock production accounts for a sizeable share of global greenhouse gas emissions, numerous technical options have been identified to mitigate these emissions. In this review, a subset of these options, which have proven to be effective, are discussed. These include measures to reduce CH4 emissions from enteric fermentation by ruminants, the largest single emission source from the global livestock sector, and for reducing CH4 and N2O emissions from manure. A unique feature of this review is the high level of attention given to interactions between mitigation options and productivity. Among the feed supplement options for lowering enteric emissions, dietary lipids, nitrates and ionophores are identified as the most effective. Forage quality, feed processing and precision feeding have the best prospects among the various available feed and feed management measures. With regard to manure, dietary measures that reduce the amount of N excreted (e.g. better matching of dietary protein to animal needs), shift N excretion from urine to faeces (e.g. tannin inclusion at low levels) and reduce the amount of fermentable organic matter excreted are recommended. Among the many 'end-of-pipe' measures available for manure management, approaches that capture and/or process CH4 emissions during storage (e.g. anaerobic digestion, biofiltration, composting), as well as subsurface injection of manure, are among the most encouraging options flagged in this section of the review. The importance of a multiple gas perspective is critical when assessing mitigation potentials, because most of the options reviewed show strong interactions among sources of greenhouse gas (GHG) emissions. The paper reviews current knowledge on potential pollution swapping, whereby the reduction of one GHG or emission source leads to unintended increases in another.

Novel AC Servo Rotating and Linear Composite Driving Device for Plastic Forming Equipment

NASA Astrophysics Data System (ADS)

Liang, Jin-Tao; Zhao, Sheng-Dun; Li, Yong-Yi; Zhu, Mu-Zhi

2017-07-01

The existing plastic forming equipment are mostly driven by traditional AC motors with long transmission chains, low efficiency, large size, low precision and poor dynamic response are the common disadvantages. In order to realize high performance forming processes, the driving device should be improved, especially for complicated processing motions. Based on electric servo direct drive technology, a novel AC servo rotating and linear composite driving device is proposed, which features implementing both spindle rotation and feed motion without transmission, so that compact structure and precise control can be achieved. Flux switching topology is employed in the rotating drive component for strong robustness, and fractional slot is employed in the linear direct drive component for large force capability. Then the mechanical structure for compositing rotation and linear motion is designed. A device prototype is manufactured, machining of each component and the whole assembly are presented respectively. Commercial servo amplifiers are utilized to construct the control system of the proposed device. To validate the effectiveness of the proposed composite driving device, experimental study on the dynamic test benches are conducted. The results indicate that the output torque can attain to 420 N·m and the dynamic tracking errors are less than about 0.3 rad in the rotating drive. the dynamic tracking errors are less than about 1.6 mm in the linear feed. The proposed research provides a method to construct high efficiency and accuracy direct driving device in plastic forming equipment.

Impact of applying edible oils to silk channels on ear pests of sweet corn

USDA-ARS?s Scientific Manuscript database

The impact of applying vegetable oils to corn silks on ear-feeding insects in sweet corn production was evaluated in 2006 and 2007. Six vegetable oils used in this experiment were canola, corn, olive, peanut, sesame, and soybean. Water and two commercial insecticidal oils (Neemix' neem oil and Sun...

21 CFR 1.276 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-04-01

... the United States. If an article of food is wild fish, including seafood that was caught or harvested..., food and feed additives, dietary supplements and dietary ingredients, infant formula, beverages... 21 Food and Drugs 1 2010-04-01 2010-04-01 false What definitions apply to this subpart? 1.276...

Precision manufacturing for clinical-quality regenerative medicines.

PubMed

Williams, David J; Thomas, Robert J; Hourd, Paul C; Chandra, Amit; Ratcliffe, Elizabeth; Liu, Yang; Rayment, Erin A; Archer, J Richard

2012-08-28

Innovations in engineering applied to healthcare make a significant difference to people's lives. Market growth is guaranteed by demographics. Regulation and requirements for good manufacturing practice-extreme levels of repeatability and reliability-demand high-precision process and measurement solutions. Emerging technologies using living biological materials add complexity. This paper presents some results of work demonstrating the precision automated manufacture of living materials, particularly the expansion of populations of human stem cells for therapeutic use as regenerative medicines. The paper also describes quality engineering techniques for precision process design and improvement, and identifies the requirements for manufacturing technology and measurement systems evolution for such therapies.

Dietary vitamin E dosage and source affects meat quality parameters in light weight lambs.

PubMed

Leal, Leonel N; Beltrán, José A; Alonso, Verónica; Bello, José M; den Hartog, Leo A; Hendriks, Wouter H; Martín-Tereso, Javier

2018-03-01

Supra-nutritional vitamin E supplementation is a commonly used approach to delay lipid oxidation and colour deterioration in lamb and beef meat marketed under modified atmosphere packaging. However, these applications lack a precise calibration of dose for the desired effect and, in addition, limited information is available regarding the use of natural vitamin E for this purpose. Three hundred and sixty Rasa Aragonesa lambs were fed diets supplemented with all-rac-α-tocopheryl acetate (250, 500, 1000 and 2000 mg kg -1 compound feed), RRR-α-tocopheryl acetate (125, 250, 500 and 1000 mg kg -1 compound feed) and a basal diet without vitamin E supplementation for 14 days before slaughter at 25.8 ± 1.67 kg body weight. Vitamin E supplementation had no effect (P > 0.05) on average daily weight gain, feed intake and feed efficiency. Display time had larger effects on lipid oxidation, colour stability, myoglobin forms and meat discolouration parameters compared to vitamin E supplementation. However, vitamin E source and dosage significantly extended meat shelf-life as indicated by lipid oxidation, redness, hue angle, metmyoglobin formation, deoxymyoglobin formation, A 580-630 and I SO2 . The quantification of these effects demonstrated that the biological activity value of 1.36 used to distinguish both vitamin E sources is not appropriate for meat quality enhancing properties. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Discrete neurochemical coding of distinguishable motivational processes: insights from nucleus accumbens control of feeding.

PubMed

Baldo, Brian A; Kelley, Ann E

2007-04-01

The idea that nucleus accumbens (Acb) dopamine transmission contributes to the neural mediation of reward, at least in a general sense, has achieved wide acceptance. Nevertheless, debate remains over the precise nature of dopamine's role in reward and even over the nature of reward itself. In the present article, evidence is reviewed from studies of food intake, feeding microstructure, instrumental responding for food reinforcement, and dopamine efflux associated with feeding, which suggests that reward processing in the Acb is best understood as an interaction among distinct processes coded by discrete neurotransmitter systems. In agreement with several theories of Acb dopamine function, it is proposed here that allocation of motor effort in seeking food or food-associated conditioned stimuli can be dissociated from computations relevant to the hedonic evaluation of food during the consummatory act. The former appears to depend upon Acb dopamine transmission and the latter upon striatal opioid peptide release. Moreover, dopamine transmission may play a role in 'stamping in' associations between motor acts and goal attainment and perhaps also neural representations corresponding to rewarding outcomes. Finally, evidence is reviewed that amino acid transmission specifically in the Acb shell acts as a central 'circuit breaker' to flexibly enable or terminate the consummatory act, via descending connections to hypothalamic feeding control systems. The heuristic framework outlined above may help explain why dopamine-compromising manipulations that strongly diminish instrumental goal-seeking behaviors leave consummatory activity relatively unaffected.

An improved wavelet neural network medical image segmentation algorithm with combined maximum entropy

NASA Astrophysics Data System (ADS)

Hu, Xiaoqian; Tao, Jinxu; Ye, Zhongfu; Qiu, Bensheng; Xu, Jinzhang

2018-05-01

In order to solve the problem of medical image segmentation, a wavelet neural network medical image segmentation algorithm based on combined maximum entropy criterion is proposed. Firstly, we use bee colony algorithm to optimize the network parameters of wavelet neural network, get the parameters of network structure, initial weights and threshold values, and so on, we can quickly converge to higher precision when training, and avoid to falling into relative extremum; then the optimal number of iterations is obtained by calculating the maximum entropy of the segmented image, so as to achieve the automatic and accurate segmentation effect. Medical image segmentation experiments show that the proposed algorithm can reduce sample training time effectively and improve convergence precision, and segmentation effect is more accurate and effective than traditional BP neural network (back propagation neural network : a multilayer feed forward neural network which trained according to the error backward propagation algorithm.

Apparatus and Method to Enable Precision and Fast Laser Frequency Tuning

NASA Technical Reports Server (NTRS)

Chen, Jeffrey R. (Inventor); Numata, Kenji (Inventor); Wu, Stewart T. (Inventor); Yang, Guangning (Inventor)

2015-01-01

An apparatus and method is provided to enable precision and fast laser frequency tuning. For instance, a fast tunable slave laser may be dynamically offset-locked to a reference laser line using an optical phase-locked loop. The slave laser is heterodyned against a reference laser line to generate a beatnote that is subsequently frequency divided. The phase difference between the divided beatnote and a reference signal may be detected to generate an error signal proportional to the phase difference. The error signal is converted into appropriate feedback signals to phase lock the divided beatnote to the reference signal. The slave laser frequency target may be rapidly changed based on a combination of a dynamically changing frequency of the reference signal, the frequency dividing factor, and an effective polarity of the error signal. Feed-forward signals may be generated to accelerate the slave laser frequency switching through laser tuning ports.

Approximating quantum many-body wave functions using artificial neural networks

NASA Astrophysics Data System (ADS)

Cai, Zi; Liu, Jinguo

2018-01-01

In this paper, we demonstrate the expressibility of artificial neural networks (ANNs) in quantum many-body physics by showing that a feed-forward neural network with a small number of hidden layers can be trained to approximate with high precision the ground states of some notable quantum many-body systems. We consider the one-dimensional free bosons and fermions, spinless fermions on a square lattice away from half-filling, as well as frustrated quantum magnetism with a rapidly oscillating ground-state characteristic function. In the latter case, an ANN with a standard architecture fails, while that with a slightly modified one successfully learns the frustration-induced complex sign rule in the ground state and approximates the ground states with high precisions. As an example of practical use of our method, we also perform the variational method to explore the ground state of an antiferromagnetic J1-J2 Heisenberg model.

The effect of 1-week feed restriction on performance, digestibility of nutrients and digestive system development in the growing rabbit.

PubMed

Tůmová, E; Volek, Z; Chodová, D; Härtlová, H; Makovický, P; Svobodová, J; Ebeid, T A; Uhlířová, L

2016-01-01

A 3 to 4 week feed restriction of about 20% to 25% of the free intake is widely applied in rabbit breeding systems to reduce post-weaning digestive disorders. However, a short intensive feed restriction is described in few studies and can be beneficial for growing rabbits due to a longer re-alimentation period. The aim of this study was to evaluate the effect of ad libitum (AL) and two restriction levels of feeding (50 and 65 g/rabbit per day) applied for 1 week on performance, gastrointestinal morphology and physiological parameters during the restriction and during the re-alimentation period. Rabbits were divided into three experimental groups: AL rabbits were fed AL, R1 rabbits were restricted from 42 to 49 days of age and received 50 g daily (29% of AL) and R2 rabbits were restricted at the same age and were fed 65 g of feed daily (37% of AL). In the 1(st) week after weaning and in the weeks after restriction, all the groups were fed AL. During the restriction period, daily weight gain (DWG) in R1 significantly dropped to 11% (experiment 1) and 5% (experiment 2) compared with rabbits in the AL group, although they were fed 29% of AL, whereas in the R2 group it decreased to 20% (experiment 1) and 10% (experiment 2). In the week following feed restriction, DWG in the restricted groups increased (P<0.001) to 166% and 148% in R1 and to 128% and 145% in R2. Restricted rabbits in both the experiments reached up to 90% to 93% of the final live weight (70 days) of the AL group. Over the entire experimental period, feed restriction significantly decreased feed intake to 85% to 88% of the AL group; however, the feed conversion ratio was lower (P<0.05) only in experiment 1 (-6% in R1 and -4% in R2). Digestibilities of CP and fat were not significantly higher during the restriction period and during the 1(st) week of re-alimentation compared with the AL group. Significant interactions between feeding regime and age revealed the shortest large intestine in the AL group at 49 days of age and the longest at 70 days in the AL and R1 groups. Small intestinal villi were significantly higher and the crypts were significantly deeper in the restricted groups. It could be concluded that short intensive feed restriction increased digestible area in the small and large intestines, including the height of villi and depth of crypts, which might be involved in the compensatory growth and defence mechanism.

Practical experiences with an extended screening strategy for genetically modified organisms (GMOs) in real-life samples.

PubMed

Scholtens, Ingrid; Laurensse, Emile; Molenaar, Bonnie; Zaaijer, Stephanie; Gaballo, Heidi; Boleij, Peter; Bak, Arno; Kok, Esther

2013-09-25

Nowadays most animal feed products imported into Europe have a GMO (genetically modified organism) label. This means that they contain European Union (EU)-authorized GMOs. For enforcement of these labeling requirements, it is necessary, with the rising number of EU-authorized GMOs, to perform an increasing number of analyses. In addition to this, it is necessary to test products for the potential presence of EU-unauthorized GMOs. Analysis for EU-authorized and -unauthorized GMOs in animal feed has thus become laborious and expensive. Initial screening steps may reduce the number of GMO identification methods that need to be applied, but with the increasing diversity also screening with GMO elements has become more complex. For the present study, the application of an informative detailed 24-element screening and subsequent identification strategy was applied in 50 animal feed samples. Almost all feed samples were labeled as containing GMO-derived materials. The main goal of the study was therefore to investigate if a detailed screening strategy would reduce the number of subsequent identification analyses. An additional goal was to test the samples in this way for the potential presence of EU-unauthorized GMOs. Finally, to test the robustness of the approach, eight of the samples were tested in a concise interlaboratory study. No significant differences were found between the results of the two laboratories.

Maternal Representations of their Children in relation to Feeding Beliefs and Practices among Low-Income Mothers of Young Children

PubMed Central

Leung, Christy Y.Y.; Miller, Alison L.; Lumeng, Julie C.; Kaciroti, Niko A.; Rosenblum, Katherine L.

2015-01-01

Identifying maternal characteristics in relation to child feeding is important for addressing the current childhood obesity epidemic. The present study examines whether maternal representations of their children are associated with feeding beliefs and practices. Maternal representations refer to mothers' affective and cognitive perspectives regarding their children and their subjective experiences of their relationships with their children. This key maternal characteristic has not been examined in association with maternal feeding. Thus the purpose of the current study was to examine whether maternal representations of their children, reflected by Working Model of the Child Interview typologies (Balanced, Disengaged, or Distorted), were associated with maternal feeding beliefs (Authority, Confidence, and Investment) and practices (Pressure to Eat, Restriction, and Monitoring) among low-income mothers of young children, with maternal education examined as a covariate. Results showed that Balanced mothers were most likely to demonstrate high authority, Distorted mothers were least likely to demonstrate confidence, and Disengaged mothers were least likely to demonstrate investment in child feeding. Moreover, Balanced mothers were least likely to pressure their children to eat. Findings are discussed with regard to implications for the study of childhood obesity and for applied preventions. PMID:26145277

Spectroscopy applied to feed additives of the European Union Reference Laboratory: a valuable tool for traceability.

PubMed

Omar, Jone; Slowikowski, Boleslaw; Boix, Ana; von Holst, Christoph

2017-08-01

Feed additives need to be authorised to be placed on the market according to Regulation (EU) No. 1831/2003. Next to laying down the procedural requirements, the regulation creates the European Union Reference Laboratory for Feed Additives (EURL-FA) and requires that applicants send samples to the EURL-FA. Once authorised, the characteristics of the marketed feed additives should correspond to those deposited in the sample bank of the EURL-FA. For this purpose, the submitted samples were subjected to near-infrared (NIR) and Raman spectroscopy for spectral characterisation. These techniques have the valuable potential of characterising the feed additives in a non-destructive manner without any complicated sample preparation. This paper describes the capability of spectroscopy for a rapid characterisation of products to establish whether specific authorisation criteria are met. This study is based on the analysis of feed additive samples from different categories and functional groups, namely products containing (1) selenium, (2) zinc and manganese, (3) vitamins and (4) essential oils such as oregano and thyme oil. The use of chemometrics turned out to be crucial, especially in cases where the differentiation of spectra by visual inspection was very difficult.

Effect of feed-gas humidity on nitrogen atmospheric-pressure plasma jet for biological applications.

PubMed

Stephan, Karl D; McLean, Robert J C; DeLeon, Gian; Melnikov, Vadim

2016-11-14

We investigate the effect of feed-gas humidity on the oxidative properties of an atmospheric-pressure plasma jet using nitrogen gas. Plasma jets operating at atmospheric pressure are finding uses in medical and biological settings for sterilization and other applications involving oxidative stress applied to organisms. Most jets use noble gases, but some researchers use less expensive nitrogen gas. The feed-gas water content (humidity) has been found to influence the performance of noble-gas plasma jets, but has not yet been systematically investigated for jets using nitrogen gas. Low-humidity and high-humidity feed gases were used in a nitrogen plasma jet, and the oxidation effect of the jet was measured quantitatively using a chemical dosimeter known as FBX (ferrous sulfate-benzoic acid-xylenol orange). The plasma jet using high humidity was found to have about ten times the oxidation effect of the low-humidity jet, as measured by comparison with the addition of measured amounts of hydrogen peroxide to the FBX dosimeter. Atmospheric-pressure plasma jets using nitrogen as a feed gas have a greater oxidizing effect with a high level of humidity added to the feed gas.

Shelf-life extension of preservative-free hydrated feed using gamma pasteurization and its effect on growth performance of eel

NASA Astrophysics Data System (ADS)

Kim, Dongho; Song, Hyunpa; Lim, Sangyong; Jo, Minho; Song, Duseop; Jo, Cheorun

2012-08-01

Hydrated feed (HF) promotes the growth performance and shortens the feeding time of fish by increasing the efficiency of digestion. However, the shelf-life of HF is a concern due to its relatively higher water content. In this study, radiation pasteurization was applied to improve the shelf-life and microbiological quality of HF for fish farming. Preservative-free HF containing 25% moisture was gamma-irradiated and its microbiological and nutritional properties evaluated in addition to a practical feeding trial carried out using eel. The viable counts of bacteria and fungi in HF were 106 and 104 CFU/g, respectively. All coliform bacteria and yeast in HF were eliminated by irradiation at a dose of 5 kGy, and total aerobic bacteria were eliminated at 10 kGy. The shelf-life of the preservative-free and irradiated (10 kGy) HF was estimated as 6 months under ambient conditions. The nutritional composition of HF was stable up to 10 kGy of irradiation. Based on a feeding trial, it was proven that eel fed HF had about 20% higher growth rate than that fed dried feed.

Palatability and pharmacokinetics of flunixin when administered to sheep through feed

PubMed Central

Pippia, Joe; Colditz, Ian G.; Hinch, Geoff N.; Petherick, Carol J.; Lee, Caroline

2016-01-01

Applying analgesics to feed is a potentially easy method of providing pain-relief to sheep and lambs that undergo painful husbandry procedures. To be effective, the medicated feed needs to be readily accepted by sheep and its consumption needs to result in therapeutic concentrations of the drug. In the present experiment, pelleted feed was supplemented with flunixin (4.0 mg/kg live weight) and offered to eight sheep. To test the palatability of flunixin, the individually penned sheep were offered normal feed and feed supplemented with flunixin in separate troughs for two consecutive days. A trend for a day by feed-type (control versus flunixin supplemented) interaction suggested that sheep may have had an initial mild aversion to pellets supplemented with flunixin on the first day of exposure, however, by on the second day there was no difference in consumption of normal feed and feed supplemented with flunixin. To test pharmacokinetics, sheep were offered 800 g of flunixin supplemented feed for a 12 h period. Blood samples were taken over 48 h and plasma drug concentrations were determined using ultra-high-pressure liquid chromatography, negative electrospray ionisation and tandem mass spectrometry. The mean ± S.D. time required to reach maximum concentration was 6.00 ± 4.14 h and ranged from 1 to 12 h. Average maximum plasma concentration was 1.78 ± 0.48 µg/mL and ranged from 1.61 to 2.80 µg/mL. The average half-life of flunixin was 7.95 ± 0.77 h and there was a mean residence time of 13.62 ± 1.17 h. Free access to flunixin supplemented feed enabled all sheep to obtain inferred therapeutic concentrations of flunixin in plasma within 6 h of starting to consume the feed. Provision of an analgesic in feed may be an alternative practical method for providing pain relief to sheep. PMID:26989633

The infant feeding choices and experiences of women living with HIV in Kinshasa, Democratic Republic of Congo.

PubMed

Maman, Suzanne; Cathcart, Rebecca; Burkhardt, Gillian; Omba, Serge; Thompson, Deidre; Behets, Frieda

2012-01-01

HIV transmission through breastfeeding is a significant public health challenge. While breastfeeding provides important nutrition, and results in reduced morbidity and mortality, there is a risk of HIV transmission through breastfeeding. International prevention of mother-to-child transmission (PMTCT) guidelines recommend exclusive breastfeeding for six months among HIV-infected women on antiretroviral therapy. Promoting exclusive feeding has proved difficult in settings where mixed feeding is a cultural norm. Understanding the factors that influence HIV infected women's infant feeding choices and practices is critical to promoting adherence to PMTCT guidelines. We conducted in-depth interviews with 40 HIV+ pregnant and post-partum women in Kinshasa, Democratic Republic of Congo to understand their infant feeding experiences. Interviews were conducted in Lingala, and transcribed and translated into French for analysis. Deductive and inductive codes were applied, and matrices were created to facilitate cross-case analysis. Women had limited understanding of the specific mechanisms through which their infant feeding practices influenced HIV transmission risk. Clinical staff was the primary source of women's knowledge of HIV mother-to-child-transmission. Among the 24 post-partum women in the sample, seven women adhered to exclusive breastfeeding and two women to exclusive formula feeding for at least six months. Women's beliefs and awareness about HIV transmission through breastfeeding, as well as the information and support from clinical staff and other members of their support networks positively influenced their exclusive feeding. Common barriers to exclusive feeding included financial constraints, breast health problems, misinformation about HIV transmission, local norms, and prior feeding experiences. Health care workers play a key role in providing correct information on PMTCT and supporting women's infant feeding choices to adhere to guidelines of exclusive infant feeding. Optimizing provider-patient communication and creating a supportive environment surrounding infant feeding is critical.

Feed-drug interaction of orally applied butyrate and phenobarbital on hepatic cytochrome P450 activity in chickens.

PubMed

Mátis, G; Kulcsár, A; Petrilla, J; Hermándy-Berencz, K; Neogrády, Zs

2016-08-01

The expression of hepatic drug-metabolizing cytochrome P450 (CYP) enzymes may be affected by several nutrition-derived compounds, such as by the commonly applied feed additive butyrate, possibly leading to feed-drug interactions. The aim of this study was to provide some evidence if butyrate can alter the activity of hepatic CYPs in chickens exposed to CYP-inducing xenobiotics, monitoring for the first time the possibility of such interaction. Ross 308 chickens in the grower phase were treated with daily intracoelomal phenobarbital (PB) injection (80 mg/kg BW), applied as a non-specific CYP-inducer, simultaneously with two different doses of intra-ingluvial sodium butyrate boluses (0.25 and 1.25 g/kg BW) for 5 days. Activity of CYP2H and CYP3A subfamilies was assessed by specific enzyme assays from isolated liver microsomes. According to our results, the lower dose of orally administered butyrate significantly attenuated the PB-triggered elevation of both hepatic CYP2H and CYP3A activities, which might be in association with the partly common signalling pathways of butyrate and CYP-inducing drugs, such as that of PB. Based on these data, butyrate may take part in pharmacoepigenetic interactions with simultaneously applied drugs or other CYP-inducing xenobiotics, with possible consequences for food safety and pharmacotherapy. Butyrate was found to be capable to maintain physiological CYP activity by attenuating CYP induction, underlining the safety of butyrate application in poultry nutrition. Journal of Animal Physiology and Animal Nutrition © 2015 Blackwell Verlag GmbH.

The precision seismometer based on planar electrochemical transducer

NASA Astrophysics Data System (ADS)

Shabalina, A. S.; Krishtop, V. G.

2016-12-01

In this paper we investigate the possibility of applying a planar electrochemical trancducer (ECT) as a sensing element for a precision seismometer with a high inertial mass. The precision seismometer based on simplest planar ECT was manufactured and tested. We investigated the amplitude-frequency and volt-ampere characteristics, self-noise level and the transducer's impedance frequency dependence. One of the key characteristics for the seismometer is the intrinsic noise level, this work focuses on the self-noise level.

Waveform synthesis for imaging and ranging applications

DOEpatents

Doerry, Armin W.; Dudley, Peter A.; Dubert, Dale F.; Tise, Bertice L.

2004-12-07

Frequency dependent corrections are provided for quadrature imbalance and Local Oscillator (LO) feed-through. An operational procedure filters imbalance and LO feed-through effects without prior calibration or equalization. Waveform generation can be adjusted/corrected in a synthetic aperture radar system (SAR), where a rolling phase shift is applied to the SAR's QDWS signal where it is demodulated in a receiver; unwanted energies, such as LO feed-through and/or imbalance energy, are separated from a desired signal in Doppler; the separated energy is filtered from the receiver leaving the desired signal; and the separated energy in the receiver is measured to determine the degree of imbalance that is represented by it. Calibration methods can also be implemented into synthesis. The degree of LO feed-through and imbalance can be used to determine calibration values that can then be provided as compensation for frequency dependent errors in components, such as the QDWS and SSB mixer, affecting quadrature signal quality.

Characterization of the chemical variation of feed coal and coal combustion products from a power plant utilizing low sulfur Powder River Basin coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Affolter, R.H.; Brownfield, M.E.; Cathcart, J.D.

2000-07-01

The US Geological Survey and the University of Kentucky Center for Applied Energy Research, in collaboration with an Indiana utility, are studying a coal-fired power plant burning Powder River Basin coal. This investigation involves a systematic study of the chemical and mineralogical characteristics of feed coal and coal combustion products (CCPs) from a 1,300-megawatt (MW) power unit. The main goal of this study is to characterize the temporal chemical variability of the feed coal, fly ash, and bottom ash by looking at the major-, minor-, and trace-element compositions and their associations with the feed coal mineralogy. Emphasis is also placedmore » on the abundance and modes of occurrence of elements of potential environmental concern that may affect the utilization of these CCPs and coals.« less

Coplanar UHF RFID tag antenna with U-shaped inductively coupled feed for metallic applications.

PubMed

Salman, Karrar Naji; Ismail, Alyani; Raja Abdullah, Raja Syamsul Azmir; Saeedi, Tale

2017-01-01

In this paper, we present a novel compact, coplanar, tag antenna design for metallic objects. Electrically small antenna has designed for a UHF RFID (860-960 MHz) based on a proximity-coupled feed through. Furthermore, two symmetrical Via-loaded coplanar grounds fed by a U-shaped inductively coupled feed through an embedded transmission line. This configuration results in an antenna with dimensions of 31 × 19.5 × 3.065 mm3 at 915 MHz, and the total gain for the antenna is 0.12 dBi. The Via-loaded coplanar and U-shaped inductively coupled feeds allow the antenna to provide flexible tuning in terms of antenna impedance. In addition, a figure of merit is applied for the proposed tag antenna, and the results are presented. The read range is measured to be 4.2 m, which is very close to simulated values. This antenna measurement shows very good agreement with simulations.

Waveform Synthesizer For Imaging And Ranging Applications

DOEpatents

Dubbert, Dale F.; Dudley, Peter A.; Doerry, Armin W.; Tise, Bertice L.

2004-12-28

Frequency dependent corrections are provided for Local Oscillator (LO) feed-through. An operational procedure filters LO feed-through effects without prior calibration or equalization. Waveform generation can be adjusted/corrected in a synthetic aperture radar system (SAR), where a rolling phase shift is applied to the SAR's QDWS signal where it is demodulated in a receiver, unwanted energies, such as LO feed-through energy, are separated from a desired signal in Doppler; the separated energy is filtered from the receiver leaving the desired signal; and the separated energy in the receiver is measured to determine the degree of imbalance that is represented by it. Calibration methods can also be implemented into synthesis. The degree of LO feed-through can be used to determine calibration values that can then be provided as compensation for frequency dependent errors in components, such as the QDWS and SSB mixer, affecting quadrature signal quality.

Economics of production efficiency: Nutritional grouping of the lactating cow.

PubMed

Cabrera, V E; Kalantari, A S

2016-01-01

Nutritional grouping of lactating cows under total mixed ration (TMR) feeding systems has been discussed in the literature since 1970. Most studies have concluded that using multiple, more-homogeneous TMR feeding groups is economically beneficial because of either nutrient cost savings, improved productivity, or both. Nonetheless, no consensus has been formed around this technique nor has it been widely adopted. By using optimal criteria for grouping and more precise nutrient specifications of diets, the latest studies have reported a consistently greater income over feed cost ($/cow per year) with multiple TMR groups compared with 1 TMR (3 TMR=$46 and 2 TMR=$21 to $39). Critical factors that determine the economic value of nutritional grouping are: (1) criteria for grouping, (2) nutrient specifications of diets, (3) effects on milk production, (4) health and environmental benefits, (5) number, size, and frequency of grouping, and (6) additional costs and benefits. It has been documented that grouping cows according to their simultaneous nutritional requirements (a.k.a., cluster grouping) is optimal. Cluster grouping is superior to other methods, such as grouping according to days in milk, milk production, or production and body weight combined. However, the dairy industry still uses less-than-optimal grouping criteria. Using cluster grouping will enhance the positive economic effects of multiple TMR. In addition, nutrient specifications of diets for groups do not seem optimal either. Milk lead factors, which are only based on group average milk production, are used. Diets could, however, be formulated more precisely based on overall group nutrient requirements. Providing more precise diets should also be in favor of grouping economics. Furthermore, an area that requires more attention is the potential negative effect of grouping on the milk production of moved cows because of either or both social interactions or diet concentration changes. Although the literature is inconclusive on this subject matter, the latest studies indicate that multiple TMR groups economically outperform 1 TMR, even after considering plausible potential milk losses when grouping. Moreover, additional positive effects of nutritional grouping of improved herd health and environmental stewardship should be translated into economic benefits. Finally, additional costs of management, labor, facilities, and equipment required for grouping are farm specific. The few studies that have integrated these factors in their analyses found that multiple TMR groups would still be economically superior to 1 TMR. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

VLBI2010 Demonstrator Project

NASA Astrophysics Data System (ADS)

Niell, A.

2008-12-01

The next generation geodetic VLBI instrument is being developed with a goal of 1 mm position uncertainty in twenty-four hours. Knowing that spatial and temporal fluctuations in the atmosphere delay are a major component of the error in position determination, the VLBI2010 committee has carried out a large number of simulations to arrive at design goals for the antenna system. These goals are fast slewing antennas and high delay precision per observation. With existing and anticipated data recording capabilities, these translate to an antenna diameter of 12 m or larger and a per-observation delay precision of approximately 4 psec. The major innovation for the VLBI2010 concept that allows the use of relatively small antennas to achieve these goals is the proposal to observe in four frequency bands, instead of the two currently used, in order to gain the higher precision of phase delays compared to the group delay. The other advance that enables the use of small antennas is the significant increase in data acquisition rates that has been made possible by the development of disk-based recorders and digital back ends. To evaluate this concept, a prototype of the feed-to-recorder system has been implemented by the Broadband Development Team* on two antennas, the 5 m MV-3 antenna at Goddard Space Flight Center near Washington, D.C., and the 18 m Westford antenna at Haystack Observatory near Boston. The system includes a broadband feed and low noise amplifiers covering the range approximately 2 GHz to 13 GHz, all cooled to 20K; a newly developed phase calibration generator; a flexible local oscillator (LO) that allows selection of any band in the range of the feed/LNAs; Digital Back End; and a disk-based recorder capable of a sustained rate of 2 gigabits per second (gbps). Four sets of the LO/DBE/recorder chain are used at each antenna to give a total record rate of 8 gbps. The systems have been successfully used in the band 8.5 to 9 GHz with one set of the recorder chain. Observations demonstrating the full four-band configuration are planned for October. In this talk the results of these tests, the improvements that are anticipated for the operational VLBI2010 network, and the status of other developments in the next generation of geodetic VLBI systems will be presented. * Bruce Whittier, Mike Titus, Jason SooHoo, Dan Smythe, Alan Rogers, Jay Redmond, Mike Poirier, Chuck Kodak, Alan Hinton, Ed Himwich, Skip Gordon, Mark Evangelista, Irv Diegel, Brian Corey, Tom Clark, Chris Beaudoin (in reverse alphabetical order)

Applying geophysical surveys for studying subsurface geology of monogenetic volcanic fields: the example of La Garrotxa Volcanic Field (NE of Iberian Peninsula)

NASA Astrophysics Data System (ADS)

Bolós, Xavier; Barde-Cabusson, Stéphanie; Pedrazzi, Dario; Martí, Joan; Casas, Albert; Lovera, Raúl; Nadal-Sala, Daniel

2014-05-01

Improving knowledge of the shallowest part of the feeding system of monogenetic volcanoes and the relationship with the subsurface geology is an important task. We applied high-precision geophysical techniques that are self-potential and electrical resistivity tomography, for the exploration of the uppermost part of the substrate of La Garrotxa Volcanic Field, which is part of the European Cenozoic Rift System. Previous geophysical studies carried out in the same area at a less detailed scale were aimed at identifying deeper structures, and together constitute the basis to establish volcanic susceptibility in La Garrotxa. Self-potential study allowed identifying key areas where electrical resistivity tomography could be conducted. Dykes and faults associated with several monogenetic cones were identified through the generation of resistivity models. The combined results confirm that shallow tectonics controlling the distribution of the foci of eruptive activity in this volcanic zone mainly correspond to NNW-SSE and accessorily by NNE-SSW Neogene extensional fissures and faults and concretely show the associated magmatic intrusions. These studies show that previous alpine tectonic structures played no apparent role in controlling the loci of this volcanism. Furthermore, the results obtained show that the changes in eruption dynamics occurring at different vents located at relatively short distances in this volcanic area can be controlled by shallow stratigraphical, structural, and hydrogeological features underneath these monogenetic volcanoes. This study was partially funded by the Beca Ciutat d'Olot en Ciències Naturals and the European Commission (FT7 Theme: ENV.2011.1.3.3-1; Grant 282759: "VUELCO").

Reliability of Pressure Ulcer Rates: How Precisely Can We Differentiate Among Hospital Units, and Does the Standard Signal‐Noise Reliability Measure Reflect This Precision?

PubMed Central

Cramer, Emily

2016-01-01

Abstract Hospital performance reports often include rankings of unit pressure ulcer rates. Differentiating among units on the basis of quality requires reliable measurement. Our objectives were to describe and apply methods for assessing reliability of hospital‐acquired pressure ulcer rates and evaluate a standard signal‐noise reliability measure as an indicator of precision of differentiation among units. Quarterly pressure ulcer data from 8,199 critical care, step‐down, medical, surgical, and medical‐surgical nursing units from 1,299 US hospitals were analyzed. Using beta‐binomial models, we estimated between‐unit variability (signal) and within‐unit variability (noise) in annual unit pressure ulcer rates. Signal‐noise reliability was computed as the ratio of between‐unit variability to the total of between‐ and within‐unit variability. To assess precision of differentiation among units based on ranked pressure ulcer rates, we simulated data to estimate the probabilities of a unit's observed pressure ulcer rate rank in a given sample falling within five and ten percentiles of its true rank, and the probabilities of units with ulcer rates in the highest quartile and highest decile being identified as such. We assessed the signal‐noise measure as an indicator of differentiation precision by computing its correlations with these probabilities. Pressure ulcer rates based on a single year of quarterly or weekly prevalence surveys were too susceptible to noise to allow for precise differentiation among units, and signal‐noise reliability was a poor indicator of precision of differentiation. To ensure precise differentiation on the basis of true differences, alternative methods of assessing reliability should be applied to measures purported to differentiate among providers or units based on quality. © 2016 The Authors. Research in Nursing & Health published by Wiley Periodicals, Inc. PMID:27223598

An experimental hut study to quantify the effect of DDT and airborne pyrethroids on entomological parameters of malaria transmission

PubMed Central

2014-01-01

Background Current malaria vector control programmes rely on insecticides with rapid contact toxicity. However, spatial repellents can also be applied to reduce man-vector contact, which might ultimately impact malaria transmission. The aim of this study was to quantify effects of airborne pyrethroids from coils and DDT used an indoor residual spray (IRS) on entomological parameters that influence malaria transmission. Methods The effect of Transfluthrin and Metofluthrin coils compared to DDT on house entry, exit and indoor feeding behaviour of Anopheles gambiae sensu lato were measured in experimental huts in the field and in the semi-field. Outcomes were deterrence - reduction in house entry of mosquitoes; irritancy or excito-repellency – induced premature exit of mosquitoes; blood feeding inhibition and effect on mosquito fecundity. Results Transfluthrin coils, Metofluthrin coils and DDT reduced human vector contact through deterrence by 38%, 30% and 8%, respectively and induced half of the mosquitoes to leave huts before feeding (56%, 55% and 48%, respectively). Almost all mosquitoes inside huts with Metofluthrin and Transfluthrin coils and more than three quarters of mosquitoes in the DDT hut did not feed, almost none laid eggs and 67%, 72% and 70% of all mosquitoes collected from Transfluthrin, Metofluthrin and DDT huts, respectively had died after 24 hours. Conclusion This study highlights that airborne pyrethroids and DDT affect a range of anopheline mosquito behaviours that are important parameters in malaria transmission, namely deterrence, irritancy/excito-repellency and blood-feeding inhibition. These effects are in addition to significant toxicity and reduced mosquito fecundity that affect mosquito densities and, therefore, provide community protection against diseases for both users and non-users. Airborne insecticides and freshly applied DDT had similar effects on deterrence, irritancy and feeding inhibition. Therefore, it is suggested that airborne pyrethroids, if delivered in suitable formats, may complement existing mainstream vector control tools. PMID:24693934

Protocol for a feasibility trial for improving breast feeding initiation and continuation: assets-based infant feeding help before and after birth (ABA)

PubMed Central

Jolly, Kate; Ingram, Jenny; Clarke, Joanne; Johnson, Debbie; Trickey, Heather; Thomson, Gill; Dombrowski, Stephan U; Sitch, Alice; Dykes, Fiona; Feltham, Max G; Darwent, Kirsty; MacArthur, Christine; Roberts, Tracy

2018-01-01

Introduction Breast feeding improves the health of mothers and infants; the UK has low rates, with marked socioeconomic inequalities. While trials of peer support services have been effective in some settings, UK trials have not improved breast feeding rates. Qualitative research suggests that many women are alienated by the focus on breast feeding. We propose a change from breast feeding-focused interactions to respecting a woman’s feeding choices, inclusion of behaviour change theory and an increased intensity of contacts in the 2 weeks after birth when many women cease to breast feed. This will take place alongside an assets-based approach that focuses on the positive capability of individuals, their social networks and communities. We propose a feasibility study for a multicentre randomised controlled trial of the Assets feeding help Before and After birth (ABA) infant feeding service versus usual care. Methods and analysis A two-arm, non-blinded randomised feasibility study will be conducted in two UK localities. Women expecting their first baby will be eligible, regardless of feeding intention. The ABA infant feeding intervention will apply a proactive, assets-based, woman-centred, non-judgemental approach, delivered antenatally and postnatally tailored through face-to-face contacts, telephone and SMS texts. Outcomes will test the feasibility of delivering the intervention with recommended intensity and duration to disadvantaged women; acceptability to women, feeding helpers and professionals; and feasibility of a future randomised controlled trial (RCT), detailing recruitment rates, willingness to be randomised, follow-up rates at 3 days, 8 weeks and 6 months, and level of outcome completion. Outcomes of the proposed full trial will also be collected. Mixed methods will include qualitative interviews with women/partners, feeding helpers and health service staff; feeding helper logs; and review of audio-recorded helper–women interactions to assess intervention fidelity. Ethics and dissemination Study results will inform the design of a larger multicentre RCT. The National Research Ethics Service Committee approved the study protocol. Trial registration number ISRCTN14760978; Pre-results. PMID:29362263

Protocol for a feasibility trial for improving breast feeding initiation and continuation: assets-based infant feeding help before and after birth (ABA).

PubMed

Jolly, Kate; Ingram, Jenny; Clarke, Joanne; Johnson, Debbie; Trickey, Heather; Thomson, Gill; Dombrowski, Stephan U; Sitch, Alice; Dykes, Fiona; Feltham, Max G; Darwent, Kirsty; MacArthur, Christine; Roberts, Tracy; Hoddinott, Pat

2018-01-23

Breast feeding improves the health of mothers and infants; the UK has low rates, with marked socioeconomic inequalities. While trials of peer support services have been effective in some settings, UK trials have not improved breast feeding rates. Qualitative research suggests that many women are alienated by the focus on breast feeding. We propose a change from breast feeding-focused interactions to respecting a woman's feeding choices, inclusion of behaviour change theory and an increased intensity of contacts in the 2 weeks after birth when many women cease to breast feed. This will take place alongside an assets-based approach that focuses on the positive capability of individuals, their social networks and communities.We propose a feasibility study for a multicentre randomised controlled trial of the Assets feeding help Before and After birth (ABA) infant feeding service versus usual care. A two-arm, non-blinded randomised feasibility study will be conducted in two UK localities. Women expecting their first baby will be eligible, regardless of feeding intention. The ABA infant feeding intervention will apply a proactive, assets-based, woman-centred, non-judgemental approach, delivered antenatally and postnatally tailored through face-to-face contacts, telephone and SMS texts. Outcomes will test the feasibility of delivering the intervention with recommended intensity and duration to disadvantaged women; acceptability to women, feeding helpers and professionals; and feasibility of a future randomised controlled trial (RCT), detailing recruitment rates, willingness to be randomised, follow-up rates at 3 days, 8 weeks and 6 months, and level of outcome completion. Outcomes of the proposed full trial will also be collected. Mixed methods will include qualitative interviews with women/partners, feeding helpers and health service staff; feeding helper logs; and review of audio-recorded helper-women interactions to assess intervention fidelity. Study results will inform the design of a larger multicentre RCT. The National Research Ethics Service Committee approved the study protocol. ISRCTN14760978; Pre-results. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Peanut Oil

MedlinePlus

... Rectally, peanut oil is used in ointments and medicinal oils for treating constipation. Pharmaceutical companies use peanut ... applied to the skin, or used rectally in medicinal amounts. Special precautions & warnings: Pregnancy and breast-feeding: ...

Predicting the environmental impacts of chicken systems in the United Kingdom through a life cycle assessment: egg production systems.

PubMed

Leinonen, I; Williams, A G; Wiseman, J; Guy, J; Kyriazakis, I

2012-01-01

The aim of this study was to apply a life cycle assessment (LCA) method, from cradle to gate, to quantify the environmental burdens per 1,000 kg of eggs produced in the 4 major hen-egg production systems in the United Kingdom: 1) cage, 2) barn, 3) free range, and 4) organic. The analysis was based on an approach that applied a structural model for the industry and mechanistic submodels for animal performance, crop production, and nutrient flows. Baseline feeds representative of those used by the UK egg production industry were used. Typical figures from the UK egg production industry, feed intake, mortality of birds, farm energy, and material use in different systems were applied. Monte Carlo simulations were used to quantify the uncertainties in the outputs and allow for comparisons between the systems. The number of birds required to produce 1,000 kg of eggs was highest in the organic and lowest in the cage system; similarly, the amount of feed consumed per bird was highest in the organic and lowest in the cage system. These general differences in productivity largely affected the differences in the environmental impacts between the systems. Feed production, processing, and transport caused greater impacts compared with those from any other component of production; that is, 54 to 75% of the primary energy use and 64 to 72% of the global warming potential of the systems. Electricity (used mainly for ventilation, automatic feeding, and lighting) had the second greatest impact in primary energy use (16-38%). Gas and oil (used mainly for heating in pullet rearing and incineration of dead layer birds) used 7 to 14% of the total primary energy. Manure had the greatest impact on the acidification and eutrophication potentials of the systems because of ammonia emissions that contributed to both of these potentials and nitrate leaching that only affected eutrophication potential. The LCA method allows for comparisons between systems and for the identification of hotspots of environmental impacts that could be subject to mitigation.

Regular monitoring of breast-feeding rates: feasible and sustainable. The Emilia-Romagna experience.

PubMed

Di Mario, Simona; Borsari, Silvana; Verdini, Eleonora; Battaglia, Sergio; Cisbani, Luca; Sforza, Stefano; Cuoghi, Chiara; Basevi, Vittorio

2017-08-01

An efficient breast-feeding monitoring system should be in place in every country to assist policy makers and health professionals plan activities to reach optimal breast-feeding rates. Design/Setting/Subjects From March to June 2015, breast-feeding rates at 3 and 5 months of age were monitored in Emilia-Romagna, an Italian region, using four questions added to a newly developed paediatric immunization database with single records for each individual. Data were collected at primary-care centres. Breast-feeding definitions and 24 h recall as recommended by the WHO were used. Direct age standardization was applied to breast-feeding rates. Record linkage with the medical birth database was attempted to identify maternal, pregnancy and delivery factors associated with full breast-feeding rates at 3 and 5 months of age. Data on breast-feeding were collected for 14044 infants. The mean regional full breast-feeding rate at 3 months was 52 %; differences between local health authorities ranged from 42 to 62 %. At 5 months of age, the mean regional full breast-feeding rate dropped to 33 % (range between local health authorities: 26 to 46 %). Record linkage with the birth certificate database was successful for 93 % of records. Total observations more than doubled with respect to the previous regional survey. The new monitoring system implemented in 2015 in Emilia-Romagna region, totally integrated with the immunization database, has proved to be feasible, sustainable and more efficient than the previous one. This system can be a model for other regions and countries where the vast majority of mothers obtain vaccinations from public health facilities and that already have an immunization database in place.

An artificial neural network to predict resting energy expenditure in obesity.

PubMed

Disse, Emmanuel; Ledoux, Séverine; Bétry, Cécile; Caussy, Cyrielle; Maitrepierre, Christine; Coupaye, Muriel; Laville, Martine; Simon, Chantal

2017-09-01

The resting energy expenditure (REE) determination is important in nutrition for adequate dietary prescription. The gold standard i.e. indirect calorimetry is not available in clinical settings. Thus, several predictive equations have been developed, but they lack of accuracy in subjects with extreme weight including obese populations. Artificial neural networks (ANN) are useful predictive tools in the area of artificial intelligence, used in numerous clinical fields. The aim of this study was to determine the relevance of ANN in predicting REE in obesity. A Multi-Layer Perceptron (MLP) feed-forward neural network with a back propagation algorithm was created and cross-validated in a cohort of 565 obese subjects (BMI within 30-50 kg m -2 ) with weight, height, sex and age as clinical inputs and REE measured by indirect calorimetry as output. The predictive performances of ANN were compared to those of 23 predictive REE equations in the training set and in two independent sets of 100 and 237 obese subjects for external validation. Among the 23 established prediction equations for REE evaluated, the Harris & Benedict equations recalculated by Roza were the most accurate for the obese population, followed by the USA DRI, Müller and the original Harris & Benedict equations. The final 5-fold cross-validated three-layer 4-3-1 feed-forward back propagation ANN model developed in that study improved precision and accuracy of REE prediction over linear equations (precision = 68.1%, MAPE = 8.6% and RMSPE = 210 kcal/d), independently from BMI subgroups within 30-50 kg m -2 . External validation confirmed the better predictive performances of ANN model (precision = 73% and 65%, MAPE = 7.7% and 8.6%, RMSPE = 187 kcal/d and 200 kcal/d in the 2 independent datasets) for the prediction of REE in obese subjects. We developed and validated an ANN model for the prediction of REE in obese subjects that is more precise and accurate than established REE predictive equations independent from BMI subgroups. For convenient use in clinical settings, we provide a simple ANN-REE calculator available at: https://www.crnh-rhone-alpes.fr/fr/ANN-REE-Calculator. Copyright © 2017 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Tunable laser techniques for improving the precision of observational astronomy

NASA Astrophysics Data System (ADS)

Cramer, Claire E.; Brown, Steven W.; Lykke, Keith R.; Woodward, John T.; Bailey, Stephen; Schlegel, David J.; Bolton, Adam S.; Brownstein, Joel; Doherty, Peter E.; Stubbs, Christopher W.; Vaz, Amali; Szentgyorgyi, Andrew

2012-09-01

Improving the precision of observational astronomy requires not only new telescopes and instrumentation, but also advances in observing protocols, calibrations and data analysis. The Laser Applications Group at the National Institute of Standards and Technology in Gaithersburg, Maryland has been applying advances in detector metrology and tunable laser calibrations to problems in astronomy since 2007. Using similar measurement techniques, we have addressed a number of seemingly disparate issues: precision flux calibration for broad-band imaging, precision wavelength calibration for high-resolution spectroscopy, and precision PSF mapping for fiber spectrographs of any resolution. In each case, we rely on robust, commercially-available laboratory technology that is readily adapted to use at an observatory. In this paper, we give an overview of these techniques.

Precision Medicine: The New Frontier in Idiopathic Pulmonary Fibrosis.

PubMed

Brownell, Robert; Kaminski, Naftali; Woodruff, Prescott G; Bradford, Williamson Z; Richeldi, Luca; Martinez, Fernando J; Collard, Harold R

2016-06-01

Precision medicine is defined by the National Institute of Health's Precision Medicine Initiative Working Group as an approach to disease treatment that takes into account individual variability in genes, environment, and lifestyle. There has been increased interest in applying the concept of precision medicine to idiopathic pulmonary fibrosis, in particular to search for genetic and molecular biomarker-based profiles (so called endotypes) that identify mechanistically distinct disease subgroups. The relevance of precision medicine to idiopathic pulmonary fibrosis is yet to be established, but we believe that it holds great promise to provide targeted and highly effective therapies to patients. In this manuscript, we describe the field's nascent efforts in genetic/molecular endotype identification and how environmental and behavioral subgroups may also be relevant to disease management.

Changes in behavioral responses of Lygus lineolaris (Hemiptera: Miridae) from various applied signal voltages during EPG recordings

USDA-ARS?s Scientific Manuscript database

A 3rd-generation AC-DC electrical penetration graph (EPG) monitor was used to study feeding behaviors of pre-reproductive adult Lygus lineolaris (Hemiptera: Miridae) on pinhead (<3mm) cotton squares, applying different signal voltages at several input impedances. The AC-DC monitor allows a user to s...

Comparison of three different techniques for application of water solutions to Finn Chambers®.

PubMed

Frick-Engfeldt, Malin; Gruvberger, Birgitta; Isaksson, Marléne; Hauksson, Inese; Pontén, Ann; Bruze, Magnus

2010-11-01

With regard to contact allergy, the dose of a sensitizer per unit skin area is an important factor for both sensitization and elicitation, and therefore a known amount/volume of test preparation should be applied at patch testing. To compare three different techniques for the application of aqueous solutions to Finn Chambers, in order to determine the precision and accuracy of each technique when the recommended 15 µl volume is applied. Four technicians applied formaldehyde 1.0% aq. (wt/vol) and methylchloroisothiazolinone/methylisothiazolinone 200 ppm (wt/vol) in sets of 10 onto Finn Chambers, with three different techniques: (i) micro-pipetting; (ii) dripping the solutions; and (iii) dripping the solutions followed by removal of excess solution with a soft tissue. Assessment of the variations was performed with the use of descriptive data. The ability to apply the exact amount was assessed by Fisher's exact test by categorizing each application as in or out of the range 12-18 µl. The micro-pipette technique had the best accuracy and precision, as well as the lowest inter-individual variation. The technique in which excess solution was removed had good precision, but failed in the application of the defined amount, i.e. 15 µl. © 2010 John Wiley & Sons A/S.

[The evaluation of organizational structure and work hygiene in milk kitchen centers in Poland on the basis of questionnaire].

PubMed

Weker, H; Rudzka-Kańtoch, Z

1999-01-01

On the basis of available publications and obligatory legal regulations regarding the organisation of collective feeding patterns in Social Service Health Centres a questionnaire study was established to examine the way milk kitchen function in Poland. The study covered 533 milk kitchen centres (in hospitals, orphanages and crèches) from February to December 1997. The afore-mentioned study analysed the general characteristics of the milk kitchen centre, its type of work, supervisory methods and the personnel's hygiene. From the results of this research it can be concluded that the organisational structure of the milk centres was appropriate, appliances and equipment in the majority centres were adequate but basis utensils were insufficient. It is obvious that dietetic feeding methods for this particular group of children are insufficiently applied. Only 22.2% of the centres apply the recommended proposals i.e. without boiling, without pasteurisation, ready for consumption when preparing, infant formulae, follow-up formulae and other mixed products. Work hygiene and health quality of production in the milk kitchen centres is subject to systematic controls by competent individuals from the State Sanitary Inspection services. In the years 1995-96, 72 samples of infant food that mainly came from hospital milk kitchen centres were taken due to the poor microbiological quality of the food. The considerable changes that have taken place over the last few years as far as infant feeding is concerned, for example, the promotion of breast-feeding, taking advantage of prepared dietetic products for infants (infant formulae, follow-up formulae, vegetable products, fruits, vegetable-meat products, cereal products) require changes at the organisational level of infant collective feeding which was confirmed by the afore-mentioned study.

Carers' experiences of home enteral feeding: A survey exploring medicines administration challenges and strategies.

PubMed

Alsaeed, D; Furniss, D; Blandford, A; Smith, F; Orlu, M

2018-06-01

The use of enteral tube feeding at home is becoming more widespread, with patients ranging in age and diseases. Dysphagia and swallowing difficulties can compromise nutritional intake and the administration of oral medications, affecting therapeutic outcomes negatively. Carers' experiences of medicines administration and medicines optimization have not been explored fully. The objectives of this study were to identify issues carers experience in medicines administration; the strategies they have developed to cope; and suggestions to improve the medicines administration process. An online survey was promoted nationally; 42 carers completed it. Descriptive statistical analysis was applied, as well as thematic analysis of open-ended responses. Results were compared against the 4 principles of medicines optimization. 93% of respondents administered medications with enteral feeding tubes, but only 62% had received advice from healthcare professionals and only 8% had received written information on how to do so. Responses identified 5 medicines administration issues experienced by carers; 4 strategies they developed to cope; and 3 main areas of suggestions to improve medicines administration via enteral feeding at home. The 4 principles of medicines optimization have not previously been applied to enteral feeding. We present a novel account of carers' experiences, for example coping with ill-suited formulations and a lack of training and support, which should inform better practice (Principle 1). Carers sometimes experience suboptimal choice of medicines (Principle 2). Carers' practices are not always well-informed and may affect therapeutic outcomes and safety (Principle 3). There is scope for improvement in carer training, education and support to better support medicines optimization (Principle 4). © 2018 The Authors. Journal of Clinical Pharmacy and Therapeutics Published by John Wiley & Sons Ltd.

Development of a foraging model framework to reliably estimate daily food consumption by young fishes

USGS Publications Warehouse

Deslauriers, David; Rosburg, Alex J.; Chipps, Steven R.

2017-01-01

We developed a foraging model for young fishes that incorporates handling and digestion rate to estimate daily food consumption. Feeding trials were used to quantify functional feeding response, satiation, and gut evacuation rate. Once parameterized, the foraging model was then applied to evaluate effects of prey type, prey density, water temperature, and fish size on daily feeding rate by age-0 (19–70 mm) pallid sturgeon (Scaphirhynchus albus). Prey consumption was positively related to prey density (for fish >30 mm) and water temperature, but negatively related to prey size and the presence of sand substrate. Model evaluation results revealed good agreement between observed estimates of daily consumption and those predicted by the model (r2 = 0.95). Model simulations showed that fish feeding on Chironomidae or Ephemeroptera larvae were able to gain mass, whereas fish feeding solely on zooplankton lost mass under most conditions. By accounting for satiation and digestive processes in addition to handling time and prey density, the model provides realistic estimates of daily food consumption that can prove useful for evaluating rearing conditions for age-0 fishes.

Hydrothermal carbonization of sewage sludge: The effect of feed-water pH on fate and risk of heavy metals in hydrochars.

PubMed

Zhai, Yunbo; Liu, Xiangmin; Zhu, Yun; Peng, Chuan; Wang, Tengfei; Zhu, Luo; Li, Caiting; Zeng, Guangming

2016-10-01

In this study, the effect of feed-water pH (pH=2-12) on fate and risk of heavy metals (HMs) in hydrochars (HCs) was investigated. Hydrothermal carbonization (HTC) of sewage sludge (SS) was carried out with different feed-water pH at 270°C. The research results showed that changing feed-water pH had a positive effect on accumulating Pb, Ni, Cd and Zn in HCs. Chemical forms of Cu and Cr converted from an unstable state to stable in the alkaline environment while in the acidic condition was opposite. The effect of feed-water pH on the chemical forms of HMs was variable but not significant. Risk assessments of Igeo, Er(i), RAC and RI were applied to evaluate the accumulation levels of individual metal, the potential ecological risks, the bio-availabilities and the comprehensive toxicity and sensitivity of HMs, respectively. The lowest pollution level of HMs was obtained at 270°C with pH=11. Copyright © 2016 Elsevier Ltd. All rights reserved.

Powering the High-Luminosity Triplets

NASA Astrophysics Data System (ADS)

Ballarino, A.; Burnet, J. P.

The powering of the magnets in the LHC High-Luminosity Triplets requires production and transfer of more than 150 kA of DC current. High precision power converters will be adopted, and novel High Temperature Superconducting (HTS) current leads and MgB2 based transfer lines will provide the electrical link between the power converters and the magnets. This chapter gives an overview of the systems conceived in the framework of the LHC High-Luminosity upgrade for feeding the superconducting magnet circuits. The focus is on requirements, challenges and novel developments.

Comparison of tool feed influence in CNC polishing between a novel circular-random path and other pseudo-random paths.

PubMed

Takizawa, Ken; Beaucamp, Anthony

2017-09-18

A new category of circular pseudo-random paths is proposed in order to suppress repetitive patterns and improve surface waviness on ultra-precision polished surfaces. Random paths in prior research had many corners, therefore deceleration of the polishing tool affected the surface waviness. The new random path can suppress velocity changes of the polishing tool and thus restrict degradation of the surface waviness, making it suitable for applications with stringent mid-spatial-frequency requirements such as photomask blanks for EUV lithography.

MASS SPECTROMETER LEAK

DOEpatents

Shields, W.R.

1960-10-18

An improved valve is described for precisely regulating the flow of a sample fluid to be analyzed, such as in a mass spectrometer, where a gas sample is allowed to "leak" into an evacuated region at a very low, controlled rate. The flow regulating valve controls minute flow of gases by allowing the gas to diffuse between two mating surfaces. The structure of the valve is such as to prevent the corrosive feed gas from contacting the bellows which is employed in the operation of the valve, thus preventing deterioration of the bellows.

Research and development of a control system for multi axis cooperative motion based on PMAC

NASA Astrophysics Data System (ADS)

Guo, Xiao-xiao; Dong, Deng-feng; Zhou, Wei-hu

2017-10-01

Based on Programmable Multi-axes Controller (PMAC), a design of a multi axis motion control system for the simulator of spatial targets' dynamic optical properties is proposed. According to analysis the properties of spatial targets' simulator motion control system, using IPC as the main control layer, TurboPMAC2 as the control layer to meet coordinated motion control, data acquisition and analog output. A simulator using 5 servomotors which is connected with speed reducers to drive the output axis was implemented to simulate the motion of both the sun and the space target. Based on PMAC using PID and a notch filter algorithm, negative feedback, the speed and acceleration feed forward algorithm to satisfy the axis' requirements of the good stability and high precision at low speeds. In the actual system, it shows that the velocity precision is higher than 0.04 s ° and the precision of repetitive positioning is better than 0.006° when each axis is at a low-speed. Besides, the system achieves the control function of multi axis coordinated motion. The design provides an important technical support for detecting spatial targets, also promoting the theoretical research.

Issues in the design of a clinical trial with a behavioral intervention--the Zambia exclusive breast-feeding study.

PubMed

Thea, Donald M; Vwalika, Cheswa; Kasonde, Prisca; Kankasa, Chipepo; Sinkala, Moses; Semrau, Katherine; Shutes, Erin; Ayash, Christine; Tsai, Wei-Yann; Aldrovandi, Grace; Kuhn, Louise

2004-08-01

We present the rationale and design of the Zambian Exclusive Breast-feeding Study (ZEBS), a randomized trial evaluating the efficacy of short-duration exclusive breast-feeding (EBF) as a strategy to reduce postnatal human immunodeficiency virus (HIV) transmission while preserving the other health benefits of this important mode of infant feeding. One thousand two hundred HIV-positive pregnant women were recruited in Lusaka, Zambia, and followed with their infants for 24 months. In addition to Nevirapine (NVP), all women received intensive and frequent clinic- and home-based counseling to support exclusive breast-feeding. When the infant was 1 week of age, half of the women were randomly assigned to a group encouraged to abruptly (<24 h) cease all breast-feeding at 4 months. The primary outcome of the experimental (randomized) comparison is HIV-free survival at 24 months. The design is also observational and will compare HIV transmission rates between those who do and do not adhere to the counseling intervention promoting exclusive breast-feeding. Our study aims to quantify the benefit-risk ratio of early cessation of exclusive breast-feeding to interrupt mother-to-child transmission of HIV with an intensive behavioral intervention and has both observational and experimental analytic approaches. Our study design assesses efficacy and also has a prominent applied component that if the intervention is effective, it will permit rapid and sustainable adoption within low-resource communities.

Precision Farming and Precision Pest Management: The Power of New Crop Production Technologies

PubMed Central

Strickland, R. Mack; Ess, Daniel R.; Parsons, Samuel D.

1998-01-01

The use of new technologies including Geographic Information Systems (GIS), the Global Positioning System (GPS), Variable Rate Technology (VRT), and Remote Sensing (RS) is gaining acceptance in the present high-technology, precision agricultural industry. GIS provides the ability to link multiple data values for the same geo-referenced location, and provides the user with a graphical visualization of such data. When GIS is coupled with GPS and RS, management decisions can be applied in a more precise "micro-managed" manner by using VRT techniques. Such technology holds the potential to reduce agricultural crop production costs as well as crop and environmental damage. PMID:19274236

Fine-tuned Remote Laser Welding of Aluminum to Copper with Local Beam Oscillation

NASA Astrophysics Data System (ADS)

Fetzer, Florian; Jarwitz, Michael; Stritt, Peter; Weber, Rudolf; Graf, Thomas

Local beam oscillation in remote laser welding of aluminum to copper was investigated. Sheets of 1 mm thickness were welded in overlap configuration with aluminum as top material. The laser beam was scanned in a sinusoidal mode perpendicular to the direction of feed and the influence of the oscillation parameters frequency and amplitude on the weld geometry was investigated. Scanning frequencies up to 1 kHz and oscillation amplitudes in the range from 0.25 mm to 1 mm were examined. Throughout the experiments the laser power and the feed rate were kept constant. A decrease of welding depth with amplitude and frequency is found. The scanning amplitude had a strong influence and allowed coarse setting of the welding depth into the lower material, while the frequency allowed fine tuning in the order of 10% of the obtained depth. The oscillation parameters were found to act differently on the aluminum sheet compared to copper sheet regarding the amount of fused material. It is possible to influence the geometry of the fused zones separately for both sheets. Therefore the average composition in the weld can be set with high precision via the oscillation parameters. A setting of the generated intermetallics in the weld zone is possible without adjustment of laser power and feed rate.

Portable device for generation of ultra-pure water vapor feeds

NASA Astrophysics Data System (ADS)

Velin, P.; Stenman, U.; Skoglundh, M.; Carlsson, P.-A.

2017-11-01

A portable device for the generation of co-feeds of water vapor has been designed, constructed, and evaluated for flexible use as an add-on component to laboratory chemical reactors. The vapor is formed by catalytic oxidation of hydrogen, which benefits the formation of well-controlled minute concentrations of ultra-pure water. Analysis of the effluent stream by on-line mass spectrometry and Fourier transform infrared spectroscopy confirms that water vapor can be, with high precision, generated both rapidly and steadily over extended periods in the range of 100 ppm to 3 vol. % (limited by safety considerations) using a total flow of 100 to 1500 ml/min at normal temperature and pressure. Further, the device has been used complementary to a commercial water evaporator and mixing system to span water concentrations up to 12 vol. %. Finally, an operando diffuse reflective infrared Fourier transform spectroscopic measurement of palladium catalysed methane oxidation in the absence and presence of up to 1.0 vol. % water has been carried out to demonstrate the applicability of the device for co-feeding well-controlled low concentrations of water vapor to a common type of spectroscopic experiment. The possibilities of creating isotopically labeled water vapor as well as using tracer gases for dynamic experiments are discussed.

Portable device for generation of ultra-pure water vapor feeds.

PubMed

Velin, P; Stenman, U; Skoglundh, M; Carlsson, P-A

2017-11-01

A portable device for the generation of co-feeds of water vapor has been designed, constructed, and evaluated for flexible use as an add-on component to laboratory chemical reactors. The vapor is formed by catalytic oxidation of hydrogen, which benefits the formation of well-controlled minute concentrations of ultra-pure water. Analysis of the effluent stream by on-line mass spectrometry and Fourier transform infrared spectroscopy confirms that water vapor can be, with high precision, generated both rapidly and steadily over extended periods in the range of 100 ppm to 3 vol. % (limited by safety considerations) using a total flow of 100 to 1500 ml/min at normal temperature and pressure. Further, the device has been used complementary to a commercial water evaporator and mixing system to span water concentrations up to 12 vol. %. Finally, an operando diffuse reflective infrared Fourier transform spectroscopic measurement of palladium catalysed methane oxidation in the absence and presence of up to 1.0 vol. % water has been carried out to demonstrate the applicability of the device for co-feeding well-controlled low concentrations of water vapor to a common type of spectroscopic experiment. The possibilities of creating isotopically labeled water vapor as well as using tracer gases for dynamic experiments are discussed.

Effects of machining parameters on tool life and its optimization in turning mild steel with brazed carbide cutting tool

NASA Astrophysics Data System (ADS)

Dasgupta, S.; Mukherjee, S.

2016-09-01

One of the most significant factors in metal cutting is tool life. In this research work, the effects of machining parameters on tool under wet machining environment were studied. Tool life characteristics of brazed carbide cutting tool machined against mild steel and optimization of machining parameters based on Taguchi design of experiments were examined. The experiments were conducted using three factors, spindle speed, feed rate and depth of cut each having three levels. Nine experiments were performed on a high speed semi-automatic precision central lathe. ANOVA was used to determine the level of importance of the machining parameters on tool life. The optimum machining parameter combination was obtained by the analysis of S/N ratio. A mathematical model based on multiple regression analysis was developed to predict the tool life. Taguchi's orthogonal array analysis revealed the optimal combination of parameters at lower levels of spindle speed, feed rate and depth of cut which are 550 rpm, 0.2 mm/rev and 0.5mm respectively. The Main Effects plot reiterated the same. The variation of tool life with different process parameters has been plotted. Feed rate has the most significant effect on tool life followed by spindle speed and depth of cut.

Development and validation of rapid multiresidue and multi-class analysis for antibiotics and anthelmintics in feed by ultra-high-performance liquid chromatography coupled to tandem mass spectrometry.

PubMed

Robert, Christelle; Brasseur, Pierre-Yves; Dubois, Michel; Delahaut, Philippe; Gillard, Nathalie

2016-08-01

A new multi-residue method for the analysis of veterinary drugs, namely amoxicillin, chlortetracycline, colistins A and B, doxycycline, fenbendazole, flubendazole, ivermectin, lincomycin, oxytetracycline, sulfadiazine, tiamulin, tilmicosin and trimethoprim, was developed and validated for feed. After acidic extraction, the samples were centrifuged, purified by SPE and analysed by ultra-high-performance liquid chromatography coupled to tandem mass spectrometry. Quantitative validation was done in accordance with the guidelines laid down in European Commission Decision 2002/657/CE. Matrix-matched calibration with internal standards was used to reduce matrix effects. The target level was set at the authorised carryover level (1%) and validation levels were set at 0.5%, 1% and 1.5%. Method performances were evaluated by the following parameters: linearity (0.986 < R(2) < 0.999), precision (repeatability < 12.4% and reproducibility < 14.0%), accuracy (89% < recovery < 107%), sensitivity, decision limit (CCα), detection capability (CCβ), selectivity and expanded measurement uncertainty (k = 2).This method has been used successfully for three years for routine monitoring of antibiotic residues in feeds during which period 20% of samples were found to exceed the 1% authorised carryover limit and were deemed non-compliant.

Atmospheric pressure plasma jet treatment of Salmonella Enteritidis inoculated eggshells.

PubMed

Moritz, Maike; Wiacek, Claudia; Koethe, Martin; Braun, Peggy G

2017-03-20

Contamination of eggshells with Salmonella Enteritidis remains a food safety concern. In many cases human salmonellosis within the EU can be traced back to raw or undercooked eggs and egg products. Atmospheric pressure plasma is a novel decontamination method that can reduce a wide range of pathogens. The aim of this work was to evaluate the possibility of using an effective short time cold plasma treatment to inactivate Salmonella Enteritidis on the eggshell. Therefore, artificially contaminated eggshells were treated with an atmospheric pressure plasma jet under different experimental settings with various exposure times (15-300s), distances from the plasma jet nozzle to the eggshell surface (5, 8 or 12mm), feed gas compositions (Ar, Ar with 0.2, 0.5 or 1.0% O 2 ), gas flow rates (5 and 7slm) and different inoculations of Salmonella Enteritidis (10 1 -10 6 CFU/cm 2 ). Atmospheric pressure plasma could reduce Salmonella Enteritidis on eggshells significantly. Reduction factors ranged between 0.22 and 2.27 log CFU (colony-forming units). Exposure time and, particularly at 10 4 CFU/cm 2 inoculation, feed gas had a major impact on Salmonella reduction. Precisely, longer exposure times led to higher reductions and Ar as feed gas was more effective than ArO 2 mixtures. Copyright © 2017 Elsevier B.V. All rights reserved.

Development of an Ion-Pairing Reagent and HPLC-UV Method for the Detection and Quantification of Six Water-Soluble Vitamins in Animal Feed.

PubMed

Kim, Ho Jin

2016-01-01

A novel and simple method for detecting six water-soluble vitamins in animal feed using high performance liquid chromatography equipped with a photodiode array detector (HPLC/PDA) and ion-pairing reagent was developed. The chromatographic peaks of the six water-soluble vitamins were successfully identified by comparing their retention times and UV spectra with reference standards. The mobile phase was composed of buffers A (5 mM PICB-6 in 0.1% CH3COOH) and B (5 mM PICB-6 in 65% methanol). All peaks were detected using a wavelength of 270 nm. Method validation was performed in terms of linearity, sensitivity, selectivity, accuracy, and precision. The limits of detection (LODs) for the instrument employed in these experiments ranged from 25 to 197 μg/kg, and the limits of quantification (LOQs) ranged from 84 to 658 μg/kg. Average recoveries of the six water-soluble vitamins ranged from 82.3% to 98.9%. Method replication resulted in intraday and interday peak area variation of <5.6%. The developed method was specific and reliable and is therefore suitable for the routine analysis of water-soluble vitamins in animal feed.

Polymer Nanocomposite Film with Metal Rich Surface Prepared by In Situ Single-Step Formation of Palladium Nanoparticles: An Interesting Way to Combine Specific Functional Properties.

PubMed

Thompson, David; Kranbuehl, David; Espuche, Eliane

2016-10-18

This paper presents a continuous single-step route that permits preparation of a thermostable polymer/metal nanocomposite film and to combine different functional properties in a unique material. More precisely, palladium nanoparticles are in situ generated in a polyimide matrix thanks to a designed curing cycle which is applied to a polyamic acid/metal precursor solution cast on a glass plate. A metal-rich surface layer which is strongly bonded to the bulk film is formed in addition to homogeneously dispersed metal nanoparticles. This specific morphology leads to obtaining an optically reflective film. The metal nanoparticles act as gas diffusion barriers for helium, oxygen, and carbon dioxide; they induce a tortuosity effect which allows dividing the gas permeation coefficients by a factor near to 2 with respect to the neat polyimide matrix. Moreover, the ability of the in situ synthesized palladium nanoparticles to entrap hydrogen is evidenced. The nanocomposite film properties can be modulated as a function of the location of the film metal-rich surface with respect to the hydrogen feed. The synthesized nanocomposite could represent a major interest for a wide variety of applications, from specific coatings for aerospace or automotive industry, to catalysis applications or sensors.

Simultaneous determination of three classes of antibiotics in the suspended solids of swine wastewater by ultrasonic extraction, solid-phase extraction and liquid chromatography-mass spectrometry.

PubMed

Pan, Xun; Qiang, Zhimin; Ben, Weiwei; Chen, Meixue

2011-01-01

This work describes a systematic approach to the development of a method for simultaneous determination of three classes of veterinary antibiotics in the suspended solids (SS) of swine wastewater, including five sulfonamides, three tetracyclines and one macrolide (tiamulin). The entire procedures for sample pretreatment, ultrasonic extraction (USE), solid-phase extraction (SPE), and liquid chromatography-mass spectrometry (LC-MS) quantification were examined and optimized. The recovery efficiencies were found to be 76%-104% for sulfonamides, 81%-112% for tetracyclines, and 51%-64% for tiamulin at three spiking levels. The intra-day and inter-day precisions, as expressed by the relative standard deviation (RSD), were below 17%. The method detection limits (MDLs) were between 0.14 and 7.14 microg/kg, depending on a specific antibiotic studied. The developed method was applied to field samples collected from three concentrated swine feeding plants located in Beijing, Shanghai and Shandong province of China. All the investigated antibiotics were detected in both SS and liquid phase of swine wastewater, with partition coefficients (logK(d)) ranging from 0.49 to 2.30. This study demonstrates that the SS can not be ignored when determining the concentrations of antibiotics in swine wastewater.

The In Ovo Feeding Administration (Gallus Gallus)—An Emerging In Vivo Approach to Assess Bioactive Compounds with Potential Nutritional Benefits

PubMed Central

2018-01-01

In recent years, the in ovo feeding in fertilized broiler (Gallus gallus) eggs approach was further developed and currently is widely applied in the evaluation process of the effects of functional foods (primarily plant origin compounds) on the functionality of the intestinal brush border membrane, as well as potential prebiotic properties and interactions with the intestinal microbial populations. This review collates the information of potential nutrients and their effects on the mineral absorption, gut development, brush border membrane functionality, and immune system. In addition, the advantages and limitations of the in ovo feeding method in the assessment of potential prebiotic effects of plant origin compounds is discussed. PMID:29597266

Potential Application of Electronic Olfaction Systems in Feedstuffs Analysis and Animal Nutrition

PubMed Central

Campagnoli, Anna; Dell'Orto, Vittorio

2013-01-01

Electronic Olfaction Systems (EOSs) based on a variety of gas-sensing technologies have been developed to simulate in a simplified manner animal olfactory sensing systems. EOSs have been successfully applied to many applications and fields, including food technology and agriculture. Less information is available for EOS applications in the feed technology and animal nutrition sectors. Volatile Organic Compounds (VOCs), which are derived from both forages and concentrate ingredients of farm animal rations, are considered and described in this review as olfactory markers for feedstock quality and safety evaluation. EOS applications to detect VOCs from feedstuffs (as analytical matrices) are described, and some future scenarios are hypothesised. Furthermore, some EOS applications in animal feeding behaviour and organoleptic feed assessment are also described. PMID:24172280

Growth-independent cross-feeding modifies boundaries for coexistence in a bacterial mutualism.

PubMed

McCully, Alexandra L; LaSarre, Breah; McKinlay, James B

2017-09-01

Nutrient cross-feeding can stabilize microbial mutualisms, including those important for carbon cycling in nutrient-limited anaerobic environments. It remains poorly understood how nutrient limitation within natural environments impacts mutualist growth, cross-feeding levels and ultimately mutualism dynamics. We examined the effects of nutrient limitation within a mutualism using theoretical and experimental approaches with a synthetic anaerobic coculture pairing fermentative Escherichia coli and phototrophic Rhodopseudomonas palustris. In this coculture, E. coli and R. palustris resemble an anaerobic food web by cross-feeding essential carbon (organic acids) and nitrogen (ammonium) respectively. Organic acid cross-feeding stemming from E. coli fermentation can continue in a growth-independent manner during nitrogen limitation, while ammonium cross-feeding by R. palustris is growth-dependent. When ammonium cross-feeding was limited, coculture trends changed yet coexistence persisted under both homogenous and heterogenous conditions. Theoretical modelling indicated that growth-independent fermentation was crucial to sustain cooperative growth under conditions of low nutrient exchange. In contrast to stabilization at most cell densities, growth-independent fermentation inhibited mutualistic growth when the E. coli cell density was adequately high relative to that of R. palustris. Thus, growth-independent fermentation can conditionally stabilize or destabilize a mutualism, indicating the potential importance of growth-independent metabolism for nutrient-limited mutualistic communities. © 2017 Society for Applied Microbiology and John Wiley & Sons Ltd.

Transfer of arsenic from poultry feed to poultry litter: A mass balance study.

PubMed

Gupta, Sanjay K; Le, X Chris; Kachanosky, Gary; Zuidhof, Martin J; Siddique, Tariq

2018-07-15

Roxarsone (rox), an arsenic (As) containing organic compound, is a common feed additive used in poultry production. To determine if As present in rox is excreted into the poultry litter without any retention in chicken meat for safe human consumption, the transference of As from the feed to poultry excreta was assessed using two commercial chicken strains fed with and without dietary rox. The results revealed that both the strains had similar behaviour in growth (chicken weight; 2.17-2.25kg), feed consumption (282-300kgpen -1 initially containing 102 chicken) and poultry litter production (73-81kgpen -1 ) during the growth phase of 35days. Our mass balance calculations showed that chickens ingested 2669-2730mg As with the feed and excreted out 2362-2896mg As in poultry litter during the growth period of 28days when As containing feed was used, yielding As recovery between 86 and 108%. Though our complementary studies show that residual arsenic species in rox-fed chicken meat may have relevance to human exposure, insignificant retention of total As in the chicken meat substantiates our mass balance results. The results are important in evaluating the fate of feed additive used in poultry production and its potential environmental implications if As containing poultry litter is applied to soil for crop production. Copyright © 2018 Elsevier B.V. All rights reserved.

Maternal self-efficacy and feeding practices in children aged 3-6 years

PubMed Central

Doaei, Saeid; Gholamalizadeh, Maryam; Entezari, Mohammad Hassan

2015-01-01

Objective: Nutrition in childhood has an important role in current and adulthood health. Recent studies have shown that the mother’s lifestyle has an important role in the methods used by mother to feed child. This paper aimed to investigate the association between mother’s weight efficacy lifestyle with feeding practices in children aged 3- 6 years. Materials and Methods: In this cross-sectional study which was carried out in 30 primary schools of Rasht (Iran) in 2012, 165 mothers with children aged 3-6 years were participated. Mothers reported their own and their child’s demographics. Aspects of mother’s weight efficacy lifestyle and mother’s control practices were assessed using Weight Efficacy Lifestyle (WEL) questionnaire and Comprehensive Feeding Practices questionnaire (CFPQ) respectively. Height and weight of mothers participated in the study were measured. The role of mother’s weight efficacy in predicting child’s feeding practices was assessed using linear regression. Results: Results showed that mother’s weight efficacy was related to child feeding practices. The mothers with similar weight efficacy lifestyle applied similar methods in child nutrition. Mothers with better weight efficacy used more encourage balance and variety, environmental control, child involvement and less emotion regulation using foods. Conclusion: ‎ ‏ ‏‎ The result of the ‎study showed that maternal ‎lifestyle was associated with ‎child feeding practices.‎ PMID:27006673

Cooccurrence of Mycotoxins in Maize and Poultry Feeds from Brazil by Liquid Chromatography/Tandem Mass Spectrometry

PubMed Central

de Souza, Maria de Lourdes Mendes; Sulyok, Michael; Costa, Sônia Soares; Machinski Junior, Miguel; Sekiyama, Beatriz Leiko; Vargas, Eugenia Azevedo; Krska, Rudolf; Schuhmacher, Rainer

2013-01-01

The objective of this study was to quantitatively evaluate mycotoxins in samples of maize and poultry feed produced in Brazil. A multimycotoxin method based on HPLC-MS/MS was applied to investigate the occurrence of toxical fungal metabolites in 119 samples collected from poultry feed factory integrated poultry farms: maize grain (74), poultry feed (36), and feed factory residue (9). Twenty of 101 fungal metabolites investigated were detected and quantified in the samples: aflatoxins B1, B2, G1, and G2, fumonisins B1, B2, and B3, hydrolyzed fumonisin B1, zearalenone, agroclavine, chanoclavine, deoxynivalenol, and nivalenol, and enniatin A, A1, B, B1, beauvericin, kojic acid, and moniliformin. Most samples were contaminated with more than one mycotoxin. All samples were contaminated with fumonisins, with medians values of 1,840 μg/kg, 239 μg/kg, and 23,676 μg/kg for maize, feed, and factory residue samples, respectively. Surprisingly, beauvericin was detected in more than 90% of samples. The median contaminations of aflatoxin and trichothecenes were low, near LOD values. The factory residue presented highest contamination levels for all mycotoxins. This is the first study dealing with agroclavine, chanoclavine, enniatin A, A1, B, B1, beauvericin, and kojic acid contamination of maize and poultry feeds from Brazil. PMID:24348157

Exploring economically and environmentally viable northeastern US dairy farm strategies for coping with rising corn grain prices.

PubMed

Ghebremichael, L T; Veith, T L; Cerosaletti, P E; Dewing, D E; Rotz, C A

2009-08-01

In 2008, corn grain prices rose $115/t of DM above the 2005 average. Such an increase creates tight marginal profits for small (<100) and medium-sized (100 to 199) dairy farms in the northeastern United States importing corn grain as animal feed supplement. Particularly in New York State, dairy farmers are attempting to avoid or minimize profit losses by growing more corn silage and reducing corn grain purchases. This study applies the Integrated Farm Systems Model to 1 small and 1 medium-sized New York State dairy farm to predict 1) sediment and P loss impacts from expanding corn fields, 2) benefits of no-till or cover cropping on corn fields, and 3) alternatives to the economic challenge of the current farming system as the price ratio of milk to corn grain continues to decline. Based on the simulation results, expanding corn silage production by 3% of the cultivated farm area increased sediment and sediment-bound P losses by 41 and 18%, respectively. Implementing no-till controlled about 84% of the erosion and about 75% of the sediment-bound P that would have occurred from the conventionally tilled, expanded corn production scenario. Implementing a conventionally tilled cover crop with the conventionally tilled, expanded corn production scenario controlled both erosion and sediment-bound P, but to a lesser extent than no-till corn with no cover crop. However, annual farm net return using cover crops was slightly less than when using no-till. Increasing on-farm grass productivity while feeding cows a high-quality, high-forage diet and precise dietary P levels offered dual benefits: 1) improved farm profitability from reduced purchases of dietary protein and P supplements, and 2) decreased runoff P losses from reduced P-levels in applied manure. Moreover, alternatives such as growing additional small grains on marginal lands and increasing milk production levels demonstrated great potential in increasing farm profitability. Overall, it is crucial that conservation measures such as no-till and cover cropping be implemented on new or existing corn lands as these areas often pose the highest threat for P losses through runoff. Although alternatives that would likely provide the largest net profit were evaluated one at a time to better quantify their individual impacts, combinations of these strategies, such as no-till corn plus a minimum-till cover crop, are recommended whenever feasible.

Direct and correlated responses to selection in two lines of rabbits selected for feed efficiency under ad libitum and restricted feeding: I. Production traits and gut microbiota characteristics.

PubMed

Drouilhet, L; Achard, C S; Zemb, O; Molette, C; Gidenne, T; Larzul, C; Ruesche, J; Tircazes, A; Segura, M; Bouchez, T; Theau-Clément, M; Joly, T; Balmisse, E; Garreau, H; Gilbert, H

2016-01-01

To get insights into selection criteria for feed efficiency, 2 rabbit lines have been created: the ConsoResidual line was selected for residual feed intake (RFI) with ad libitum feeding and the ADGrestrict line was selected for ADG under restricted feeding (-20% of voluntary intake). The first objective of this study was to evaluate, after 9 generations of selection, the direct and correlated responses to selection on production traits in the 2 lines for traits recorded during growth. Second, applying the 2 feeding conditions used for selection to both selected lines plus the control unselected line (generation 0, G0) in a 2 × 3 factorial trial, the line performances were compared and the gut microbiota of the lines was characterized. The correlated responses in feed conversion ratio (FCR) were remarkably equivalent in both selected lines (-2.74 genetic σ) but correlated responses in other traits were notably different. In the ConsoResidual line, selection for decreased RFI resulted in a small negative correlated response in BW at 63 d old (BW63) and in a null response in ADG. In the ADGrestrict line, on the contrary, the correlated response in BW63 was substantial (+1.59 σ). The 2 selected lines had a FCR reduced by 0.2 point compared with the G0 line, and the same difference was found in both feeding regimens ( < 0.001). Indeed, selection on ADG would lead to heavier animals with no significant reduction of feed costs, whereas selection on RFI leads to lower feed costs and no increase of animal BW under ad libitum feeding. Altogether, our results do not suggest any genotype × environment interaction in the response to feeding regimens. The intestinal microbial communities from efficient rabbits differed from their unselected counterparts in terms of fermentation end products and microbial phylotypes, suggesting a central role of these microbes in the better feed efficiency of the rabbits.

Accuracy assessment of the Precise Point Positioning method applied for surveys and tracking moving objects in GIS environment

NASA Astrophysics Data System (ADS)

Ilieva, Tamara; Gekov, Svetoslav

2017-04-01

The Precise Point Positioning (PPP) method gives the users the opportunity to determine point locations using a single GNSS receiver. The accuracy of the determined by PPP point locations is better in comparison to the standard point positioning, due to the precise satellite orbit and clock corrections that are developed and maintained by the International GNSS Service (IGS). The aim of our current research is the accuracy assessment of the PPP method applied for surveys and tracking moving objects in GIS environment. The PPP data is collected by using preliminary developed by us software application that allows different sets of attribute data for the measurements and their accuracy to be used. The results from the PPP measurements are directly compared within the geospatial database to different other sets of terrestrial data - measurements obtained by total stations, real time kinematic and static GNSS.

Bioinspired design and macroscopic assembly of poly(vinyl alcohol)-coated graphene into kilometers-long fibers

NASA Astrophysics Data System (ADS)

Kou, Liang; Gao, Chao

2013-05-01

Nacre is characterized by its excellent mechanical performance due to the well-recognized ``brick and mortar'' structure. Many efforts have been applied to make nacre-mimicking materials, but it is still a big challenge to realize their continuous production. Here, we prepared sandwich-like building blocks of poly(vinyl alcohol) (PVA)-coated graphene, and achieved high-nanofiller-content kilometers-long fibers by continuous wet-spinning assembly technology. The fibers have a strict ``brick and mortar'' layered structure, with graphene sheet as rigid brick and PVA as soft mortar. The mortar thickness can be precisely tuned from 2.01 to 3.31 nm by the weight feed ratio of PVA to graphene, as demonstrated by both atomic force microscopy and X-ray diffraction measurements. The mechanical strength of the nacre-mimicking fibers increases with increasing the content of PVA, and it rises gradually from 81 MPa for the fiber with 53.1 wt% PVA to 161 MPa for the fiber with 65.8 wt% PVA. The mechanical performance of our fibers was independent of the molecular weight (MW) of PVA in the wide range of 2-100 kDa, indicating that low MW polymers can also be used to make strong nanocomposites. The tensile stress of fibers immersed in PVA 5 wt% solution reached ca. 200 MPa, surpassing the values of nacre and most of other nacre-mimicking materials. The nacre-mimicking fibers are highly electrically conductive (~350 S m-1) after immersing in hydroiodic acid, enabling them to connect a circuit to illuminate an LED lamp.Nacre is characterized by its excellent mechanical performance due to the well-recognized ``brick and mortar'' structure. Many efforts have been applied to make nacre-mimicking materials, but it is still a big challenge to realize their continuous production. Here, we prepared sandwich-like building blocks of poly(vinyl alcohol) (PVA)-coated graphene, and achieved high-nanofiller-content kilometers-long fibers by continuous wet-spinning assembly technology. The fibers have a strict ``brick and mortar'' layered structure, with graphene sheet as rigid brick and PVA as soft mortar. The mortar thickness can be precisely tuned from 2.01 to 3.31 nm by the weight feed ratio of PVA to graphene, as demonstrated by both atomic force microscopy and X-ray diffraction measurements. The mechanical strength of the nacre-mimicking fibers increases with increasing the content of PVA, and it rises gradually from 81 MPa for the fiber with 53.1 wt% PVA to 161 MPa for the fiber with 65.8 wt% PVA. The mechanical performance of our fibers was independent of the molecular weight (MW) of PVA in the wide range of 2-100 kDa, indicating that low MW polymers can also be used to make strong nanocomposites. The tensile stress of fibers immersed in PVA 5 wt% solution reached ca. 200 MPa, surpassing the values of nacre and most of other nacre-mimicking materials. The nacre-mimicking fibers are highly electrically conductive (~350 S m-1) after immersing in hydroiodic acid, enabling them to connect a circuit to illuminate an LED lamp. Electronic supplementary information (ESI) available: More AFM and SEM images and electrical conductivities of CRG@PVA with different feed ratios, FTIR spectra, Raman and XPS results of GO, CRG and CRG@PVA, SEM images of CRG@PVA fibers with different diameters, SEM images and conductivity of CRG@PVA fibers with different MW of PVA, the tensile curve of CRG@PVA paper, and videos of graphene knot and spring. See DOI: 10.1039/c3nr00455d

Apparatus for Precise Indium-Bump Bonding of Microchips

NASA Technical Reports Server (NTRS)

Wild, Larry; Mulder, Jerry; Alvarado, Nicholas

2005-01-01

An improved apparatus has been designed and built for use in precise positioning and pressing of a microchip onto a substrate (which could, optionally, be another microchip) for the purpose of indium-bump bonding. The apparatus (see figure) includes the following: A stereomicroscope, A stage for precise positioning of the microchip in rotation angle (theta) about the nominally vertical pressing axis and in translation along two nominally horizontal coordinate axes (x and y), and An actuator system that causes a bonding tip to press the microchip against the substrate with a precisely controlled force. In operation, the microscope and the stage are used to position the microchip under the bonding tip and to align the indium bumps on the chip and the substrate, then the actuator system is used to apply a prescribed bonding force for a prescribed time. The improved apparatus supplants a partly similar prior apparatus that operated with less precision and repeatability, producing inconsistent and unreliable bonds. Results of the use of the prior apparatus included broken microchips, uneven bonds, and bonds characterized, variously, by overcompression or undercompression. In that apparatus, the bonding force was generated and controlled by use of a micrometer head positioned over the center of a spring-loaded scale, and the force was applied to the microchip via the scale, which was equipped for digital readout of the force. The inconsistency of results was attributed to the following causes: It was not possible to control the bonding force with sufficient precision or repeatability. Particularly troublesome was the inability to control the force at levels less than the weight of 150 g. Excessive compliance in the spring-loaded scale, combined with deviations from parallelarity of the substrate and bonding-tip surfaces, gave rise to nonuniformity in the pressure applied to the microchip, thereby generating excessive stresses and deformations in the microchip. In the improved apparatus, the bonding tip and the components that hold the substrate and the microchip are more rigid and precise than in the prior apparatus, so as to ensure less deviation from parallelarity of the bonding-tip and substrate surfaces, thereby ensuring more nearly uniform distribution of bonding force over the area of the microchip. The bonding force is now applied through, and measured by, a load cell that makes it possible to exert finer control over the force. The force can be set at any value between 0 and the weight of 800 g in increments of 0.2 g.

Effects of complementary and excess diet supplementation with selected minerals on their metabolism and distribution in the body: a model study.

PubMed

Friedrich, Mariola; Podlaszewska, Grażyna; Pokorska-Niewiada, Kamila

2015-01-01

n. The study was aimed at determining, on an animal model, effects of supplementing a diet, modified by substituting whole wheat and corn grains with white flour and sucrose, with calcium, magnesium, zinc, and chromium on metabolism of the minerals and their distribution in the body. The study involved 4 groups of Wistar rat females (n = 11) fed: a standard feed (group I) containing, i.a., whole wheat and corn grains; modified feed (84% and 50% of whole wheat and corn grains, respectively, in the standard feed substituted with Type 500 wheat flour and sucrose, respectively) (group II); modified feed with complementary supplementation (elimination of Ca, Mg, Zn, and Cr deficiencies resulting from diet modification) (group III); and modified feed with excess supplementation (the same minerals applied in excess, i.e., amounts from 0.5 to 3 times higher than the deficiencies produced by diet modification) (group IV). The replacement of whole grains with white flour and sucrose, as well as the mineral  supplementation could, to some extent, imitate the contemporary eating habits and supplementation applied in food technology. The excess supplementation is, on the other hand, typical of current behaviours of various social groups. Both types of supplementation resulted in a significant increase in the perivisceral adipose tissue content, but did not affect the fat tissue content in muscles. The supplementation applied did not change the content of calcium, magnesium, and zinc in muscles, nor did it significantly change calcium and magnesium excretion with urine. However, changes in the ALP activity and calcitonin concentration did not suggest the deposition of the minerals in bones. Analysis of the results allowed to conclude that: 1) except for chromium, contents of the selected minerals in the tissues examined and urea, as well as concentrations of calcitonin and alkaline phosphatase (ALP) activities did not point to any significant effect of the supplementation applied on the body contents of those minerals; 2) effects observed as the accumulation of perivisceral, epicardial and intramuscular adipose tissue, as well as increased body weight increments could have been related to disturbed proportions of the minerals supplemented, their synergy and antagonism and, consequently, a potential generation of secondary deficiencies and excesses which could significantly affect individual metabolic pathways; 3) the intensity of changes observed was generally higher in the females receiving complementary supplementation, although their uptake of minerals studied was similar to that shown by the females kept on the standard diet.

Herd health and management of dairy cow

NASA Astrophysics Data System (ADS)

Ćaǧlayan, Alper; Yüca, Songül

2016-04-01

Herd management requires multidisciplinary practices including animal feeding, gynecology, artificial insemination, immunology, and similar topics. Animal feeding is the most delicate subject as the fodder expense is 70% of the farm cost and as nearly all of the metabolic diseases arising out as health problem are because of misfeeding. However, a business organization's being able to maintain making profit will be possible by taking a healthy calf from breeding herd every year. For this reason, precision registrations of birth and artificial insemination, following-up pregnant state of animals, and making the other animals pregnant as soon as possible should be primary aim. It should not be forgotten that diarrhea and pneumonia in calves are among the most frequently witnessed infection related health problems. Mastitis, metritis and foot diseases take an important place in mature cows. These diseases can be minimized by vaccinations that are done properly and in suitable time, in-service training of staffs, making shelters suitable for animals welfare, and improving the hygienic conditions.

Development of a general equation to determine the transfer factor feed-to-meat for radiocesium on the basis of the body mass of domestic animals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nalezinski, S.; Ruehm, W.; Wirth, E.

1996-05-01

Transfer factors from feed to meat (5{sub {integral}}), taken from literature for monogastric animals and ruminants have been correlated to their corresponding animal body mass (m{sub b}). Taking all data into account, a close relationship between both transfer factor and body mass becomes evident, yielding a regression function of (T{sub {integral}} = 8.0 x m{sub b}{sup {minus}0.91}) (r = -0.97). For monogastric animals (including poultry), the corresponding relationships are T{sub {integral}} = 1.9 x m{sub b}{sup {minus}0.72} (r = 0.78). The equations offer the opportunity to estimate the transfer factor for individual animals more precisely taking individual body masses intomore » account. They are of interest for animals, on which no or only poor data concerning radiocesium transfer factors are available. The determination of radiocesium transfer factors are reduced to a simple weighing process. 17 refs., 1 fig., 2 tabs.« less

Bidirectional Anticipation of Future Osmotic Challenges by Vasopressin Neurons.

PubMed

Mandelblat-Cerf, Yael; Kim, Angela; Burgess, Christian R; Subramanian, Siva; Tannous, Bakhos A; Lowell, Bradford B; Andermann, Mark L

2017-01-04

Ingestion of water and food are major hypo- and hyperosmotic challenges. To protect the body from osmotic stress, posterior pituitary-projecting, vasopressin-secreting neurons (VP pp neurons) counter osmotic perturbations by altering their release of vasopressin, which controls renal water excretion. Vasopressin levels begin to fall within minutes of water consumption, even prior to changes in blood osmolality. To ascertain the precise temporal dynamics by which water or food ingestion affect VP pp neuron activity, we directly recorded the spiking and calcium activity of genetically defined VP pp neurons. In states of elevated osmolality, water availability rapidly decreased VP pp neuron activity within seconds, beginning prior to water ingestion, upon presentation of water-predicting cues. In contrast, food availability following food restriction rapidly increased VP pp neuron activity within seconds, but only following feeding onset. These rapid and distinct changes in activity during drinking and feeding suggest diverse neural mechanisms underlying anticipatory regulation of VP pp neurons. Published by Elsevier Inc.

Modeling neural circuits in Parkinson's disease.

PubMed

Psiha, Maria; Vlamos, Panayiotis

2015-01-01

Parkinson's disease (PD) is caused by abnormal neural activity of the basal ganglia which are connected to the cerebral cortex in the brain surface through complex neural circuits. For a better understanding of the pathophysiological mechanisms of PD, it is important to identify the underlying PD neural circuits, and to pinpoint the precise nature of the crucial aberrations in these circuits. In this paper, the general architecture of a hybrid Multilayer Perceptron (MLP) network for modeling the neural circuits in PD is presented. The main idea of the proposed approach is to divide the parkinsonian neural circuitry system into three discrete subsystems: the external stimuli subsystem, the life-threatening events subsystem, and the basal ganglia subsystem. The proposed model, which includes the key roles of brain neural circuit in PD, is based on both feed-back and feed-forward neural networks. Specifically, a three-layer MLP neural network with feedback in the second layer was designed. The feedback in the second layer of this model simulates the dopamine modulatory effect of compacta on striatum.

Technology achievements and projections for communication satellites of the future

NASA Technical Reports Server (NTRS)

Bagwell, J. W.

1986-01-01

Multibeam systems of the future using monolithic microwave integrated circuits to provide phase control and power gain are contrasted with discrete microwave power amplifiers from 10 to 75 W and their associated waveguide feeds, phase shifters and power splitters. Challenging new enabling technology areas include advanced electrooptical control and signal feeds. Large scale MMIC's will be used incorporating on chip control interfaces, latching, and phase and amplitude control with power levels of a few watts each. Beam forming algorithms for 80 to 90 deg. wide angle scanning and precise beam forming under wide ranging environments will be required. Satelllite systems using these dynamically reconfigured multibeam antenna systems will demand greater degrees of beam interconnectivity. Multiband and multiservice users will be interconnected through the same space platform. Monolithic switching arrays operating over a wide range of RF and IF frequencies are contrasted with current IF switch technology implemented discretely. Size, weight, and performance improvements by an order of magnitude are projected.

Precise, flexible and affordable gene stacking for crop improvement.

PubMed

Chen, Weiqiang; Ow, David W

2017-09-03

The genetic engineering of plants offers a revolutionary advance for crop improvement, and the incorporation of transgenes into crop species can impart new traits that would otherwise be difficult to obtain through conventional breeding. Transgenes introduced into plants, however, can only be useful when bred out to field cultivars. As new traits are continually added to further improve transgenic cultivars, clustering new DNA near previously introduced transgenes keep from inflating the number of segregating units that breeders must assemble back into a breeding line. Here we discuss various options to introduce DNA site-specifically into an existing transgenic locus. As food security is becoming a pressing global issue, the old proverb resonates true to this day: "give a man a fish and you feed him for a day; teach a man to fish and you feed him for a lifetime." Hence, we describe a recombinase-mediate gene stacking system designed with freedom to operate, providing an affordable option for crop improvement by less developed countries where food security is most at risk.

Nest Mosquito Trap quantifies contact rates between nesting birds and mosquitoes.

PubMed

Caillouët, Kevin A; Riggan, Anna E; Rider, Mark; Bulluck, Lesley P

2012-06-01

Accurate estimates of host-vector contact rates are required for precise determination of arbovirus transmission intensity. We designed and tested a novel mosquito collection device, the Nest Mosquito Trap (NMT), to collect mosquitoes as they attempt to feed on unrestrained nesting birds in artificial nest boxes. In the laboratory, the NMT collected nearly one-third of the mosquitoes introduced to the nest boxes. We then used these laboratory data to estimate our capture efficiency of field-collected bird-seeking mosquitoes collected over 66 trap nights. We estimated that 7.5 mosquitoes per trap night attempted to feed on nesting birds in artificial nest boxes. Presence of the NMT did not have a negative effect on avian nest success when compared to occupied nest boxes that were not sampled with the trap. Future studies using the NMT may elucidate the role of nestlings in arbovirus transmission and further refine estimates of nesting bird and vector contact rates. © 2012 The Society for Vector Ecology.

Nest Mosquito Trap quantifies contact rates between nesting birds and mosquitoes

PubMed Central

Caillouët, Kevin A.; Riggan, Anna E.; Rider, Mark; Bulluck, Lesley P.

2012-01-01

Accurate estimates of host-vector contact rates are required for precise determination of arbovirus transmission intensity. We designed and tested a novel mosquito collection device, the Nest Mosquito Trap (NMT), to collect mosquitoes as they attempt to feed on unrestrained nesting birds in artificial nest boxes. In the laboratory, the NMT collected nearly one-third of the mosquitoes introduced to the nest boxes. We then used these laboratory data to estimate our capture efficiency of field-collected bird-seeking mosquitoes collected over 66 trap nights. We estimated that 7.5 mosquitoes per trap night attempted to feed on nesting birds in artificial nest boxes. Presence of the NMT did not have a negative effect on avian nest success when compared to occupied nest boxes that were not sampled with the trap. Future studies using the NMT may elucidate the role of nestlings in arbovirus transmission and further refine estimates of nesting bird and vector contact rates. PMID:22548555

Disinfection effect of non-thermal atmospheric pressure plasma for foodborne bacteria

NASA Astrophysics Data System (ADS)

Pervez, Mohammad Rasel; Inomata, Takanori; Ishijima, Tatsuo; Kakikawa, Makiko; Uesugi, Yoshihiko; Tanaka, Yasunori; Yano, Toshihiro; Miwa, Shoji; Noguchi, Akinori

2015-09-01

Non-thermal atmospheric pressure plasma (NAPP) exposure can be a suitable alternative for bacteria inactivation in food processing industry. Specimen placed in the enclosure are exposed to various reactive radicals produced within the discharge chamber. It is also exposed to the periodic variation of the electric field strength in the chamber. Dielectric barrier discharge is produced by high voltage pulse (Vpp = 18 kV, pulse width 20 μs, repetition frequency 10 kHz) in a polypropylene box (volume = 350 cm3) using helium as main feed gas. Inactivation efficiency of NAPP depends on the duration of NAPP exposure, applied voltage pulse strength and type, pulse duration, electrode separation and feed gas composition. In this study we have investigated inactivation of Bacillus lichenformis spore as an example of food borne bacteria. Keeping applied voltage, electrode configuration and total gas flow rate constant, spores are exposed to direct NAPP for different time duration while O2 concentration in the feed gas composition is varied. 10 minutes NAPP exposure resulted in ~ 3 log reduction of Bacillus lichenformis spores for 1% O2concentration (initial concentration ~ 106 / specimen). This work is supported by research and development promotion grant provided by the Hokuriku Industrial Advancement Center.

Performance evaluation of a dental handpiece in simulation of clinical finishing using a novel 2DOF in vitro apparatus.

PubMed

Yin, L; Song, X F; Qu, S F; Huang, T; Mei, J P; Yang, Z Y; Li, J

2006-11-01

This paper reports on the performance evaluation of a dental handpiece in simulation of clinical finishing using a novel two-degrees-of-freedom (2DOF) in vitro apparatus. The instrumented apparatus consisted of a two-dimensional computer-controlled coordinate worktable carrying a dental handpiece, a piezoelectric force dynamometer, and a high-speed data acquisition and signal conditioning system for simulating the clinical operations and monitoring the dental finishing processes. The performance of the dental handpiece was experimentally evaluated with respect to rotational speed, torque, and specific finishing energy under the applied clinical finishing conditions. The results show that the rotational speeds of the dental handpiece decreased by increasing either the depth of cut or the feed rate at a constant clinically applied air pressure and water flowrate. They also decreased when increasing both the tangential and normal finishing forces. The specific finishing energy decreased with an increase in either depth of cut or feed rate, while the finishing torque increased as either the depth of cut or the feed rate was increased. Implications of these results were to provide guidance for proper applications of dental handpieces in clinical practice.

Design and Validation of In-Source Atmospheric Pressure Photoionization Hydrogen/Deuterium Exchange Mass Spectrometry with Continuous Feeding of D2O

NASA Astrophysics Data System (ADS)

Acter, Thamina; Lee, Seulgidaun; Cho, Eunji; Jung, Maeng-Joon; Kim, Sunghwan

2018-01-01

In this study, continuous in-source hydrogen/deuterium exchange (HDX) atmospheric pressure photoionization (APPI) mass spectrometry (MS) with continuous feeding of D2O was developed and validated. D2O was continuously fed using a capillary line placed on the center of a metal plate positioned between the UV lamp and nebulizer. The proposed system overcomes the limitations of previously reported APPI HDX-MS approaches where deuterated solvents were premixed with sample solutions before ionization. This is particularly important for APPI because solvent composition can greatly influence ionization efficiency as well as the solubility of analytes. The experimental parameters for APPI HDX-MS with continuous feeding of D2O were optimized, and the optimized conditions were applied for the analysis of nitrogen-, oxygen-, and sulfur-containing compounds. The developed method was also applied for the analysis of the polar fraction of a petroleum sample. Thus, the data presented in this study clearly show that the proposed HDX approach can serve as an effective analytical tool for the structural analysis of complex mixtures. [Figure not available: see fulltext.

The applicability of animal health surveillance systems for post-market monitoring of potential adverse effects of genetically modified (GM) feed.

PubMed

Vince, L; Kleter, G A; Kostov, K; Pfeiffer, D U; Guitian, J

2018-04-20

A facultative post market monitoring of potential health impacts of genetically modified (GM) feedstuffs on livestock consuming these feeds after pre-market risk assessment is under ongoing consideration. Within the IPAFEED database, scientific studies on health effects beyond performance in livestock and the results of a systematic search for evidence of outcome effects due to GM feed are consolidated. These outcomes were reviewed and checked for consistency in order to identify plausible syndromes suitable for conducting surveillance. The 24 selected studies showed no consistent changes in any health parameter. There were no repeated studies in any species by GM crop type and animal species. As such, there is insufficient evidence to inform the design of surveillance systems for detecting known adverse effects. Animal health surveillance systems have been proposed for the post market monitoring of potential adverse effects in animals. Such systems were evaluated for their applicability to the detection of hypothetical adverse effects and their strengths and weaknesses to detect syndromes of concern are presented. For known adverse effects, applied controlled post-market studies may yield conclusive and high-quality evidence. For detecting unknown adverse effects, the use of existing surveillance systems may still be of interest. A simulation tool developed within the project can be adapted and applied to existing surveillance systems to explore their applicability to the detection of potential adverse effects of GM feed. Copyright © 2018. Published by Elsevier Ltd.

Radiation patterns of multimode feed-horn-coupled bolometers for FAR-IR space applications

NASA Astrophysics Data System (ADS)

Kalinauskaite, Eimante; Murphy, J. Anthony; McAuley, Ian; Trappe, Neal A.; McCarthy, Darragh N.; Bracken, Colm P.; Doherty, Stephen; Gradziel, Marcin L.; O'Sullivan, Créidhe; Wilson, Daniel; Peacocke, Tully; Maffei, Bruno; Lamarre, Jean-Michel; Ade, Peter A. R.; Savini, Giorgio

2017-02-01

A multimode horn differs from a single mode horn in that it has a larger sized waveguide feeding it. Multimode horns can therefore be utilized as high efficiency feeds for bolometric detectors, providing increased throughput and sensitivity over single mode feeds, while also ensuring good control of the beam pattern characteristics. Although a cavity mounted bolometer can be modelled as a perfect black body radiator (using reciprocity in order to calculate beam patterns), nevertheless, this is an approximation. In this paper we present how this approach can be improved to actually include the cavity coupled bolometer, now modelled as a thin absorbing film. Generally, this is a big challenge for finite element software, in that the structures are typically electrically large. However, the radiation pattern of multimode horns can be more efficiently simulated using mode matching, typically with smooth-walled waveguide modes as the basis and computing an overall scattering matrix for the horn-waveguide-cavity system. Another issue on the optical efficiency of the detectors is the presence of any free space gaps, through which power can escape. This is best dealt with treating the system as an absorber. Appropriate reflection and transmission matrices can be determined for the cavity using the natural eigenfields of the bolometer cavity system. We discuss how the approach can be applied to proposed terahertz systems, and also present results on how the approach was applied to improve beam pattern predictions on the sky for the multi-mode HFI 857GHz channel on Planck.

Effects of applying anchovy (Stolephorus insularis) substrates on the microhardness of tooth enamel in Sprague-Dawley rats

NASA Astrophysics Data System (ADS)

Hendrik, Y. C.; Puspitawati, R.; Gunawan, H. A.

2017-08-01

Anchovies (Stolephorus insularis) contain high levels of fluor in the form of CaF2. The aim of this study is to analyze changes in tooth enamel microhardness after application of anchovy substrates by feeding or as a topical fluoridation material. An in vivo study of the lower left incisors of nine Sprague-Dawley rats was conducted. The sample was comprised of baseline and treatment groups, including feeding application, topical application, negative control feeding, and negative control topical groups. The treatment groups were given 5% anchovy substrates through feeding and topical applications. After treatment, tooth samples were extracted from each of the rats for examination, and statistical analyses were performed after determining hardness numbers for enamel surfaces using Vickers microhardness tester. Vickers hardness numbers (VHNs) for anchovy substrate application and consumption by feeding (440.3 ± 24.72) were higher than for the negative control (315.80 ± 17.51). VHNs for the topical application group were higher than for the negative control (347.28 ± 28.56) and for the feeding group. The use of anchovy as a fluoridation material in form of topical application is potentially an effective method for increasing the microhardness of the tooth enamel surface

Maternal representations of their children in relation to feeding beliefs and practices among low-income mothers of young children.

PubMed

Leung, Christy Y Y; Miller, Alison L; Lumeng, Julie C; Kaciroti, Niko A; Rosenblum, Katherine L

2015-12-01

Identifying maternal characteristics in relation to child feeding is important for addressing the current childhood obesity epidemic. The present study examines whether maternal representations of their children are associated with feeding beliefs and practices. Maternal representations refer to mothers' affective and cognitive perspectives regarding their children and their subjective experiences of their relationships with their children. This key maternal characteristic has not been examined in association with maternal feeding. Thus the purpose of the current study was to examine whether maternal representations of their children, reflected by Working Model of the Child Interview typologies (Balanced, Disengaged, or Distorted), were associated with maternal feeding beliefs (Authority, Confidence, and Investment) and practices (Pressure to Eat, Restriction, and Monitoring) among low-income mothers of young children, with maternal education examined as a covariate. Results showed that Balanced mothers were most likely to demonstrate high authority, Distorted mothers were least likely to demonstrate confidence, and Disengaged mothers were least likely to demonstrate investment in child feeding. Moreover, Balanced mothers were least likely to pressure their children to eat. Findings are discussed with regard to implications for the study of childhood obesity and for applied preventions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Plane of nutrition affects the phylogenetic diversity and relative abundance of transcriptionally active methanogens in the bovine rumen.

PubMed

McGovern, Emily; McCabe, Matthew S; Cormican, Paul; Popova, Milka; Keogh, Kate; Kelly, Alan K; Kenny, David A; Waters, Sinead M

2017-10-12

Methane generated during enteric fermentation in ruminant livestock species is a major contributor to global anthropogenic greenhouse gas emissions. A period of moderate feed restriction followed by ad libitum access to feed is widely applied in cattle management to exploit the animal's compensatory growth potential and reduce feed costs. In the present study, we utilised microbial RNA from rumen digesta samples to assess the phylogenetic diversity of transcriptionally active methanogens from feed-restricted and non-restricted animals. To determine the contribution of different rumen methanogens to methanogenesis during dietary restriction of cattle, we conducted high-throughput mcrA cDNA amplicon sequencing on an Illumina MiSeq and analysed both the abundance and phylogenetic origin of different mcrA cDNA sequences. When compared to their unrestricted contemporaries, in feed-restricted animals, the methanogenic activity, based on mcrA transcript abundance, of Methanobrevibacter gottschalkii clade increased while the methanogenic activity of the Methanobrevibacter ruminantium clade and members of the Methanomassiliicoccaceae family decreased. This study shows that the quantity of feed consumed can evoke large effects on the composition of methanogenically active species in the rumen of cattle. These data potentially have major implications for targeted CH 4 mitigation approaches such as anti-methanogen vaccines and/or tailored dietary management.

Effect of Correlated Precision Errors on Uncertainty of a Subsonic Venturi Calibration

NASA Technical Reports Server (NTRS)

Hudson, S. T.; Bordelon, W. J., Jr.; Coleman, H. W.

1996-01-01

An uncertainty analysis performed in conjunction with the calibration of a subsonic venturi for use in a turbine test facility produced some unanticipated results that may have a significant impact in a variety of test situations. Precision uncertainty estimates using the preferred propagation techniques in the applicable American National Standards Institute/American Society of Mechanical Engineers standards were an order of magnitude larger than precision uncertainty estimates calculated directly from a sample of results (discharge coefficient) obtained at the same experimental set point. The differences were attributable to the effect of correlated precision errors, which previously have been considered negligible. An analysis explaining this phenomenon is presented. The article is not meant to document the venturi calibration, but rather to give a real example of results where correlated precision terms are important. The significance of the correlated precision terms could apply to many test situations.

Precision Medicine: The New Frontier in Idiopathic Pulmonary Fibrosis

PubMed Central

Brownell, Robert; Kaminski, Naftali; Woodruff, Prescott G.; Bradford, Williamson Z.; Richeldi, Luca; Martinez, Fernando J.

2016-01-01

Precision medicine is defined by the National Institute of Health’s Precision Medicine Initiative Working Group as an approach to disease treatment that takes into account individual variability in genes, environment, and lifestyle. There has been increased interest in applying the concept of precision medicine to idiopathic pulmonary fibrosis, in particular to search for genetic and molecular biomarker-based profiles (so called endotypes) that identify mechanistically distinct disease subgroups. The relevance of precision medicine to idiopathic pulmonary fibrosis is yet to be established, but we believe that it holds great promise to provide targeted and highly effective therapies to patients. In this manuscript, we describe the field’s nascent efforts in genetic/molecular endotype identification and how environmental and behavioral subgroups may also be relevant to disease management. PMID:26991475

The application of Near-Infrared Reflectance Spectroscopy (NIRS) to detect melamine adulteration of soya bean meal.

PubMed

Haughey, Simon A; Graham, Stewart F; Cancouët, Emmanuelle; Elliott, Christopher T

2013-02-15

Soya bean products are used widely in the animal feed industry as a protein based feed ingredient and have been found to be adulterated with melamine. This was highlighted in the Chinese scandal of 2008. Dehulled soya (GM and non-GM), soya hulls and toasted soya were contaminated with melamine and spectra were generated using Near Infrared Reflectance Spectroscopy (NIRS). By applying chemometrics to the spectral data, excellent calibration models and prediction statistics were obtained. The coefficients of determination (R(2)) were found to be 0.89-0.99 depending on the mathematical algorithm used, the data pre-processing applied and the sample type used. The corresponding values for the root mean square error of calibration and prediction were found to be 0.081-0.276% and 0.134-0.368%, respectively, again depending on the chemometric treatment applied to the data and sample type. In addition, adopting a qualitative approach with the spectral data and applying PCA, it was possible to discriminate between the four samples types and also, by generation of Cooman's plots, possible to distinguish between adulterated and non-adulterated samples. Copyright © 2012 Elsevier Ltd. All rights reserved.

A qualitative study of the infant feeding beliefs and behaviours of mothers with low educational attainment.

PubMed

Russell, Catherine Georgina; Taki, Sarah; Azadi, Leva; Campbell, Karen J; Laws, Rachel; Elliott, Rosalind; Denney-Wilson, Elizabeth

2016-05-21

Infancy is an important period for the promotion of healthy eating, diet and weight. However little is known about how best to engage caregivers of infants in healthy eating programs. This is particularly true for caregivers, infants and children from socioeconomically disadvantaged backgrounds who experience greater rates of overweight and obesity yet are more challenging to reach in health programs. Behaviour change interventions targeting parent-infant feeding interactions are more likely to be effective if assumptions about what needs to change for the target behaviours to occur are identified. As such we explored the precursors of key obesity promoting infant feeding practices in mothers with low educational attainment. One-on-one semi-structured telephone interviews were developed around the Capability Opportunity Motivation Behaviour (COM-B) framework and applied to parental feeding practices associated with infant excess or healthy weight gain. The target behaviours and their competing alternatives were (a) initiating breastfeeding/formula feeding, (b) prolonging breastfeeding/replacing breast milk with formula, (c) best practice formula preparation/sub-optimal formula preparation, (d) delaying the introduction of solid foods until around six months of age/introducing solids earlier than four months of age, and (e) introducing healthy first foods/introducing unhealthy first foods, and (f) feeding to appetite/use of non-nutritive (i.e., feeding for reasons other than hunger) feeding. The participants' education level was used as the indicator of socioeconomic disadvantage. Two researchers independently undertook thematic analysis. Participants were 29 mothers of infants aged 2-11 months. The COM-B elements of Social and Environmental Opportunity, Psychological Capability, and Reflective Motivation were the key elements identified as determinants of a mother's likelihood to adopt the healthy target behaviours although the relative importance of each of the COM-B factors varied with each of the target feeding behaviours. Interventions targeting healthy infant feeding practices should be tailored to the unique factors that may influence mothers' various feeding practices, taking into account motivational and social influences.

Evaluation and Management of Neonatal Dysphagia: Impact of Pharyngoesophageal Motility Studies and Multidisciplinary Feeding Strategy

PubMed Central

Jadcherla, Sudarshan R.; Stoner, Erin; Gupta, Alankar; Bates, D. Gregory; Fernandez, Soledad; Di Lorenzo, Carlo; Linscheid, Thomas

2013-01-01

Background and objectives Abnormal swallowing (dysphagia) among neonates is commonly evaluated using the videofluoroscopic swallow study (VSS). Radiological findings considered high risk for administration of oral feeding include nasopharyngeal reflux, laryngeal penetration, aspiration, or pooling. Our aims were to determine pharyngoesophageal motility correlates in neonates with dysphagia and the impact of multidisciplinary feeding strategy. Methods Twenty dysphagic neonates (mean gestation ± standard deviation [SD] = 30.9 ± 4.9 weeks; median 31.1 weeks; range = 23.7–38.6 weeks) with abnormal VSS results were evaluated at 49.9 ± 16.5 weeks (median 41.36 weeks) postmenstrual age. The subjects underwent a swallow-integrated pharyngoesophageal motility assessment of basal and adaptive swallowing reflexes using a micromanometry catheter and pneumohydraulic water perfusion system. Based on observations during the motility study, multidisciplinary feeding strategies were applied and included postural adaptation, sensory modification, hunger manipulation, and operant conditioning methods. To discriminate pharyngoesophageal manometry correlates between oral feeders and tube feeders, data were stratified based on the primary feeding method at discharge, oral feeding versus tube feeding. Results At discharge, 15 of 20 dysphagic neonates achieved oral feeding success, and the rest required chronic tube feeding. Pharyngoesophageal manometry correlates were significantly different (P <0.05) between the primary oral feeders versus the chronic tube feeders for swallow frequency, swallow propagation, presence of adaptive peristaltic reflexes, oral feeding challenge test results, and upper esophageal sphincter tone. VSS results or disease characteristics had little effect on the feeding outcomes (P = NS). Conclusions Swallow-integrated esophageal motility studies permit prolonged evaluation of swallowing reflexes and responses to stimuli under controlled conditions at cribside. The dysfunctional neuromotor mechanisms may be responsible for neonatal dysphagia or its consequences. Manometry may be a better predictor than VSS in identifying patients who are likely to succeed in vigorous intervention programs. PMID:19179881

Investigation of the performance behavior of a forward osmosis membrane system using various feed spacer materials fabricated by 3D printing technique.

PubMed

Yanar, Numan; Son, Moon; Yang, Eunmok; Kim, Yeji; Park, Hosik; Nam, Seung-Eun; Choi, Heechul

2018-07-01

Recently, feed spacer research for improving the performance of a membrane module has adopted three-dimensional (3D) printing technology. This study aims to improve the performance of membrane feed spacers by using various materials and incorporating 3D printing. The samples were fabricated after modeling with 3D computer-aided design (CAD) software to investigate the mechanical strength, water flux, reverse solute flux, and fouling performances. This research was performed using acrylonitrile butadiene styrene (ABS), polypropylene (PP), and natural polylactic acid (PLA) as printing material, and the spacer model was produced using a diamond-shaped feed spacer, with a commercially available product as a reference. The 3D printed samples were initially compared in terms of size and precision with the 3D CAD model, and deviations were observed between the products and the CAD model. Then, the spacers were tested in terms of mechanical strength, water flux, reverse solute flux, and fouling (alginate-based waste water was used as a model foulant). Although there was not much difference among the samples regarding the water flux, better performances than the commercial product were obtained for reverse solute flux and fouling resistance. When comparing the prominent performance of natural PLA with the commercial product, PLA was found to have approximately 10% less fouling (based on foulant volume per unit area and root mean square roughness values), although it showed similar water flux. Thus, another approach has been introduced for using bio-degradable materials for membrane spacers. Copyright © 2018 Elsevier Ltd. All rights reserved.

High levels of grass pollen inside European dairy farms: a role for the allergy-protective effects of environment?

PubMed

Sudre, B; Vacheyrou, M; Braun-Fahrländer, C; Normand, A-C; Waser, M; Reboux, G; Ruffaldi, P; von Mutius, E; Piarroux, R

2009-07-01

There is evidence of an allergy protective effect in children raised on farm. It has been assumed that microbial exposure may confer this protection. However in farm, little attention has been given to the pollen level and to concomitant microbiological exposure, and indoor pollen concentrations have never been precisely quantified. The kinetics of pollen in dairy farms have been studied in a pilot study (n = 9), and exposure in a sub-sample of the ongoing European birth cohort PASTURE (n = 106). Measurements of viable microorganisms and pollen were performed in air samples. To identify factors that modulate the pollen concentration multivariate regression analyses were run. Indoor pollen (95% of Poaceae fragments and grains) were significantly higher in winter than in summer (P = 0.001) and ranged between 858 to 11 265 counts/m(3) during feeding in winter, thus exceeding typical outdoor levels during the pollen season. Geometric mean in French farms was significantly higher than in German and Swiss farms (7 534, 992 and 1 079 count/m(3), respectively). The presence of a ventilation system and loose housing systems significantly reduced indoor pollen levels. This pollen concentration rise after feeding was accompanied by an increase in fungal and actinomycetal levels, whereas the concentration of bacteria was not associated with feeding. Farmers and their children who attend cowsheds during the feeding sessions are exposed perennially to high pollen concentrations. It might be speculated that the combined permanent exposure to microbes from livestock and grass pollen may initiate tolerance in children living on a farm.

Energetic responses to variation in food availability in the two mountain gorilla populations (Gorilla beringei beringei).

PubMed

Wright, Edward; Grueter, Cyril C; Seiler, Nicole; Abavandimwe, Didier; Stoinski, Tara S; Ortmann, Sylvia; Robbins, Martha M

2015-11-01

Here, we compare food availability and relate this to differences in energy intake rates, time spent feeding, and daily travel distance of gorillas in the two populations. Comparative intraspecific studies investigating spatiotemporal variation in food availability can help us understand the complex relationships between ecology, behavior, and life history in primates and are relevant to understanding hominin evolution. Differences in several variables have been documented between the two mountain gorilla populations in the Virunga Massif and Bwindi Impenetrable National Park, but few direct comparisons that link ecological conditions to feeding behavior have been made. Using similar data collection protocols we conducted vegetation sampling and nutritional analysis on important foods to estimate food availability. Detailed observations of feeding behavior were used to compute energy intake rates and daily travel distance was estimated through GPS readings. Food availability was overall lower and had greater temporal variability in Bwindi than in the Virungas. Energy intake rates and time spent feeding were similar in both populations, but energy intake rates were significantly higher in Bwindi during the period of high fruit consumption. Daily travel distances were significantly shorter in the Virungas. Overall, despite the differences in food availability, we did not find large differences in the energetics of gorillas in the two populations, although further work is needed to more precisely quantify energy expenditure and energy balance. These results emphasize that even species with high food availability can exhibit behavioral and energetic responses to variable ecological conditions, which are likely to affect growth, reproduction, and survival. © 2015 Wiley Periodicals, Inc.

Nanotechnology in agri-food production: an overview

PubMed Central

Sekhon, Bhupinder Singh

2014-01-01

Nanotechnology is one of the most important tools in modern agriculture, and agri-food nanotechnology is anticipated to become a driving economic force in the near future. Agri-food themes focus on sustainability and protection of agriculturally produced foods, including crops for human consumption and animal feeding. Nanotechnology provides new agrochemical agents and new delivery mechanisms to improve crop productivity, and it promises to reduce pesticide use. Nanotechnology can boost agricultural production, and its applications include: 1) nanoformulations of agrochemicals for applying pesticides and fertilizers for crop improvement; 2) the application of nanosensors/nanobiosensors in crop protection for the identification of diseases and residues of agrochemicals; 3) nanodevices for the genetic manipulation of plants; 4) plant disease diagnostics; 5) animal health, animal breeding, poultry production; and 6) postharvest management. Precision farming techniques could be used to further improve crop yields but not damage soil and water, reduce nitrogen loss due to leaching and emissions, as well as enhance nutrients long-term incorporation by soil microorganisms. Nanotechnology uses include nanoparticle-mediated gene or DNA transfer in plants for the development of insect-resistant varieties, food processing and storage, nanofeed additives, and increased product shelf life. Nanotechnology promises to accelerate the development of biomass-to-fuels production technologies. Experts feel that the potential benefits of nanotechnology for agriculture, food, fisheries, and aquaculture need to be balanced against concerns for the soil, water, and environment and the occupational health of workers. Raising awareness of nanotechnology in the agri-food sector, including feed and food ingredients, intelligent packaging and quick-detection systems, is one of the keys to influencing consumer acceptance. On the basis of only a handful of toxicological studies, concerns have arisen regarding the safety of nanomaterials, and researchers and companies will need to prove that these nanotechnologies do not have more of a negative impact on the environment. PMID:24966671

Post-Exercise Carbohydrate-Energy Replacement Attenuates Insulin Sensitivity and Glucose Tolerance the Following Morning in Healthy Adults

PubMed Central

Taylor, Harry L.; Wu, Ching-Lin; Chen, Yung-Chih; Wang, Pin-Ging; Betts, James A.

2018-01-01

The carbohydrate deficit induced by exercise is thought to play a key role in increased post-exercise insulin action. However, the effects of replacing carbohydrate utilized during exercise on postprandial glycaemia and insulin sensitivity are yet to be determined. This study therefore isolated the extent to which the insulin-sensitizing effects of exercise are dependent on the carbohydrate deficit induced by exercise, relative to other exercise-mediated mechanisms. Fourteen healthy adults performed a 90-min run at 70% V˙O2max starting at 1600–1700 h before ingesting either a non-caloric artificially-sweetened placebo solution (CHO-DEFICIT) or a 15% carbohydrate solution (CHO-REPLACE; 221.4 ± 59.3 g maltodextrin) to precisely replace the measured quantity of carbohydrate oxidized during exercise. The alternate treatment was then applied one week later in a randomized, placebo-controlled, and double-blinded crossover design. A standardized low-carbohydrate evening meal was consumed in both trials before overnight recovery ahead of a two-hour oral glucose tolerance test (OGTT) the following morning to assess glycemic and insulinemic responses to feeding. Compared to the CHO-DEFICIT condition, CHO-REPLACE increased the incremental area under the plasma glucose curve by a mean difference of 68 mmol·L−1 (95% CI: 4 to 132 mmol·L−1; p = 0.040) and decreased the Matsuda insulin sensitivity index by a mean difference of −2 au (95% CI: −1 to −3 au; p = 0.001). This is the first study to demonstrate that post-exercise feeding to replaceme the carbohydrate expended during exercise can attenuate glucose tolerance and insulin sensitivity the following morning. The mechanism through which exercise improves insulin sensitivity is therefore (at least in part) dependent on carbohydrate availability and so the day-to-day metabolic health benefits of exercise might be best attained by maintaining a carbohydrate deficit overnight. PMID:29370143

Switching-type regulator circuit has increased efficiency

NASA Technical Reports Server (NTRS)

Clapp, W. M.

1967-01-01

Switching series regulator circuit uses an inductive network to feed most of the current applied to the control circuit to the load. This circuit eliminates resistive losses and the need for heat sinks.

Breast-feeding and maternal risk of type 2 diabetes: a prospective study and meta-analysis.

PubMed

Jäger, Susanne; Jacobs, Simone; Kröger, Janine; Fritsche, Andreas; Schienkiewitz, Anja; Rubin, Diana; Boeing, Heiner; Schulze, Matthias B

2014-07-01

We aimed to examine the association between breast-feeding and maternal risk of type 2 diabetes and to investigate whether this association is mediated by anthropometric and biochemical factors. A case-cohort study nested within the European Prospective Investigation into Cancer and Nutrition (EPIC)-Potsdam Study between 1994 and 2005 including 1,262 childbearing women (1,059 in a random sub-cohort and 203 incident cases) mainly aged between 35 and 64 years at baseline was applied. Self-reported lifetime duration of breast-feeding was assessed by questionnaire. Blood samples were used for biomarker measurement (HDL-cholesterol, triacylglycerols, C-reactive protein, fetuin-A, γ-glutamyltransferase, adiponectin). A systematic literature search and meta-analysis was conducted of prospective cohort studies investigating breast-feeding and risk of type 2 diabetes. The HR for each additional 6 months of breast-feeding was 0.73 (95% CI 0.56, 0.94) in EPIC-Potsdam. Meta-analysis of three previous prospective studies and the current study revealed an inverse association between breast-feeding duration and risk of diabetes (pooled HR for lifetime breast-feeding duration of 6-11 months compared with no breast-feeding 0.89; 95% CI 0.82, 0.97). Adjustment for BMI and waist circumference attenuated the association (HR per six additional months in EPIC-Potsdam 0.80; 95% CI 0.61, 1.04). Further controlling for potentially mediating biomarkers largely explained this association (HR 0.89; 95% CI 0.68, 1.16). Longer duration of breast-feeding may be related to a lower risk of diabetes. This potentially protective effect seems to be reflected by a more favourable metabolic profile; however, the role of body weight as a mediator or confounder remains uncertain.

Previous exposure to dietary phytase reduces the endogenous energy losses from precision-fed chickens.

PubMed

Pirgozliev, V; Acamovic, T; Bedford, M R

2009-09-01

1. A precision feeding experiment was conducted with broiler chickens, which were previously fed on diets with or without phytase, to study the effects of previous exposure to dietary phytase supplementation on the excretions of endogenous energy, nitrogen, amino acids and minerals. 2. Female Ross 308 broiler chickens, which had previously received one of 4 experimental diets (low P maize/soy diets (control, D), D + 250 international units of phytase per kg diet (FTU), D + 500 FTU and D + 2500 FTU) were used in the study. All birds were starved and then given 50 ml of glucose solution at 44 d of age. The birds were allocated to individual metabolism cages in a randomised block design with 8 replicates of each of the 4 dietary treatments. 3. Chickens which had been previously fed on diets supplemented with phytase excreted 32% less energy and 28% less dry matter per kg metabolic body weight (W(075)) from endogenous sources, compared to birds fed the unsupplemented diet. 4. Birds previously given phytase supplemented diets excreted 60% less sodium than those given the control diet, but there was no effect on all other minerals investigated. There was no effect of diet on the excretion of endogenous N, sialic acid or amino acids. 5. The results showed that the effects of feeding chickens on diets with supplementary phytase may continue for a few days after the diets are withdrawn. This suggests that previous exposure to phytase may alter the nutritive value of follow-on diets, which may be a commercially important effect.

Endogenous opioids and feeding behavior: a 30-year historical perspective.

PubMed

Bodnar, Richard J

2004-04-01

This invited review, based on the receipt of the Third Gayle A. Olson and Richard D. Olson Prize for the publication of the outstanding behavioral article published in the journal Peptides in 2002, examines the 30-year historical perspective of the role of the endogenous opioid system in feeding behavior. The review focuses on the advances that this field has made over the past 30 years as a result of the timely discoveries that were made concerning this important neuropeptide system, and how these discoveries were quickly applied to the analysis of feeding behavior and attendant homeostatic processes. The discoveries of the opioid receptors and opioid peptides, and the establishment of their relevance to feeding behavior were pivotal in studies performed in the 1970s. The 1980s were characterized by the establishment of opioid receptor subtype agonists and antagonists and their relevance to the modulation of feeding behavior as well as by the use of general opioid antagonists in demonstrating the wide array of ingestive situations and paradigms involving the endogenous opioid system. The more recent work from the 1990s to the present, utilizes the advantages created by the cloning of the opioid receptor genes, the development of knockout and knockdown techniques, the systematic utilization of a systems neuroscience approach, and establishment of the reciprocity of how manipulations of opioid peptides and receptors affect feeding behavior with how feeding states affect levels of opioid peptides and receptors. The role of G-protein effector systems in opioid-mediated feeding responses, which was the subject of the prize-winning article, is then reviewed. Copyright 2004 Elsevier Inc.