Science.gov

Sample records for apres irradiation neutronique

  1. Etude de la microstructure d'un acier 316 titane apres vieillissement et apres irradiation aux neutrons

    NASA Astrophysics Data System (ADS)

    Brun, G.; Le Naour, J.; Vouillon, M.

    1981-10-01

    La précipitation qui se produit lors de vieillissements de longue durée entre 450 et 700°C dans un acier 316 Ti soit hypertrempé soit écroui, a été étudiée en couplant les techniques de microscopic électronique et de microanalyse X. Pour les cas expérimentaux étudiés, les résultats obtenus montrent que la composition des carbures M 23C 6 et des phases σ, Laves et χ est peu sensible aux conditions de vieillissement et dépend également peu de l'état structural initial. Leur teneur en éléments principaux de l'alliage est d'ailleurs voisine de celle des phases précipitées dans l'acier non stabilisé. Excepté les carbures de type M 6C, toutes ces phases ont une teneur en nickel inférieure à celle de la matrice. Les premiers rérultats obtenus sur des matériaux irradiés aux neutrons montrent que la précipitation sous flux est différente de celle qui se produit dans l'acier vieilli. Les phases γ' et G ainsi que les carbures riches en nickel ont été observés. L'attention a été attirée sur le fait qu'il n'y a pas de corrélation simple entre la vitesse de gonflement et la teneuer résiduelle en nickel de la matrice.

  2. Régulation de la production, par des cellules endothéliales, de cytokines pro-inflammatoires après irradiation

    NASA Astrophysics Data System (ADS)

    van der Meeren, A.; Lafont, H.; Mathé, D.

    1998-04-01

    Gamma irradiation leads to an increased production of interleukin- (IL)-6 and IL-8 by human endothelial cells. In order to regulate the radio-induced production of these pro-inflammatory cytokines, we used the immunoregulatory cytokines IL-4 and IL-10. These agents were added either before or after a 10 Gy-irradiation. Our results show that it is possible to decrease the radio-induced production of IL-6 and IL-8 with the use of IL-4 and IL-10. Differences in the intensity of the response have been observed according to the time of treatment. The anti-inflammatory potential of both IL-4 and IL-10 was more pronounced when added after irradiation. Après irradiation gamma, des cellules endothéliales humaines ont une production accrue des interleukines (IL-) -6 et -8. Dans le but de réguler la production de ces cytokines pro-inflammatoires, nous avons utilisé des cytokines dites anti-inflammatoires, l'IL-4 et l'IL-10. Ces agents ont été ajoutés soit avant soit après une irradiation de 10Gy. Nos résultats montrent qu'il est possible de diminuer les productions radio-induites d'IL-6 et d'IL-8 par l'IL-4 et l'IL-10. Des différences dans l'intensité de la réponse ont toutefois été observées selon que l'IL-4 ou l'IL-10 ont été ajoutées avant ou après irradiation; leur efficacité anti-inflammatoire étant plus marquée lorsque les cytokines sont ajoutées après l'irradiation.

  3. Calcul par simulation des paramètres dosimétriques pour le noyau cellulaire après irradiation α in vitro

    NASA Astrophysics Data System (ADS)

    Le Foll, L.; Bailly, I.; Fritsch, P.

    1998-04-01

    Determination of absorbed dose in biological targets after high LET α particules irradiation needs heavy calculations. A softwave has been developed in order to allow everyone to calculate hit probability and absorbed dose. It is particularly adapted to the study of cell cultures irradiated with electrodeposited source or α-beam accelerator. It is based first, on a random generator of α-track homogeneously distributed in 4π, second, on the evaluation of energy loss in the different media along the track and then on a statistical analysis of the results. This method is accurate and low time consuming. The target is either modelised by an ellipsoid or represented by its 3D shape recorded using confocal microscopy. Des calculs dosimétriques complexes sont nécessaires pour l'évaluation des doses délivrées dans des cibles biologiques après irradiation par des particules α de haut TEL. Un logiciel a été développé pour rendre facilement accessible le calcul de la probabilité pour atteindre la cible et de la dose absorbée. il est particulièrement adapté à l'étude des cultures cellulaires irradiées par des sources électrodéposées de radionucléides ou des accélérateurs de particules. Il repose sur un générateur de traces aléatoires, sur une approximation de la perte d'énergie dans les différents milieux traversés et sur une exploitation statistique des résultats obtenus. Cette méthode s'avère précise et rapide. La cible est modélisée par un ellipsoïde ou représentée par son image 3D obtenue en microscopie confocale.

  4. Radiosensibilité comparative des cellules épithéliales de trachée de rats après irradiation alpha in vitro

    NASA Astrophysics Data System (ADS)

    Kugel, C.; Bailly-Despiney, I.; Lagroye, I.; Poncy, J. L.

    1998-04-01

    The main risk in nuclear industry is the internal contamination after inhalation of high LET alpha emitters radionuclides. Main targets of pulmonary carcinogenesis are epithelial respiratory tract cells. An in vitro study was performed in order to determine if a difference in the radiosensitivity occured in epithelial cells from the trachea of two rat strains: Sprague Dawley and Wistar Furth-Fischer F344 after alpha exposure. The cells were irradiated after sedimentation in a specific well. The irradiation was performed using 241Am electrodeposited sources. The irradiation dosecloning efficiency relation was evaluated. A kinetic study of the proliferation and the clonal growth has also been investigated. La contamination interne par inhalation de radionucléides émetteurs alpha de haut TEL est le risque majeur de l'industrie nucléaire. Les cibles principales de la cancérogenèse pulmonaire sont les cellules épithéliales de l'appareil respiratoire. Une étude in vitro a été menée pour déterminer s'il existe une différence de radiosensibilité aux rayonnement alpha, des cellules épithéliales trachéales de deux souches de rats : Sprague Dawley et Wistar Furth-Fischer F344. Les cellules sont irradiées sédimentées au fond d'un puit spécifique à l'aide de sources électrodéposées de 241Am. L'évaluation de la survie cellulaire en fonction de la dose d'irradiation est complétée par un suivi cinétique de la formation et de la prolifération des colonies.

  5. APR-2 Tropical Cyclone Observations

    NASA Technical Reports Server (NTRS)

    Durden, S. L.; Tanelli, S.

    2011-01-01

    The Second Generation Airborne Precipitation Radar (APR-2) participated in the Genesis and Rapid Intensification Processes (GRIP) experiment in August and September of 2010, collecting a large volume of data in several tropical systems, including Hurricanes Earl and Karl. Additional measurements of tropical cyclone have been made by APR-2 in experiments prior to GRIP (namely, CAMEX-4, NAMMA, TC4); Table 1 lists all the APR-2 tropical cyclone observations. The APR-2 observations consist of the vertical structure of rain reflectivity at 13.4 and 35.6 GHz, and at both co-polarization and crosspolarization, as well as vertical Doppler measurements and crosswind measurements. APR-2 normally flies on the NASA DC-8 aircraft, as in GRIP, collecting data with a downward looking, cross-track scanning geometry. The scan limits are 25 degrees on either side of the aircraft, resulting in a roughly 10-km swath, depending on the aircraft altitude. Details of the APR-2 observation geometry and performance can be found in Sadowy et al. (2003).The multiparameter nature of the APR-2 measurements makes the collection of tropical cyclone measurements valuable for detailed studies of the processes, microphysics and dynamics of tropical cyclones, as well as weaker systems that are associated with tropical cyclone formation. In this paper, we give a brief overview of how the APR-2 data are processed. We also discuss use of the APR-2 cross-track winds to estimate various quantities of interest in in studies of storm intensification. Finally, we show examples of the standard products and derived information.

  6. Respirators: APR Issuer Self Study 33461

    SciTech Connect

    Chochoms, Michael

    2016-07-13

    Respirators: APR Issuer Self-Study (course 33461) is designed to introduce and familiarize employees selected as air-purifying respirator (APR) issuers at Los Alamos National Laboratory (LANL) with the responsibilities, limitations, procedures, and resources for issuing APRs at LANL. The goal is to enable these issuers to consistently provide proper, functioning APRs to authorized users

  7. Soins Aux Brules Apres Un Accident Nucleaire

    PubMed Central

    Bargues, L.; Donat, N.; Jault, P.; Leclerc, T.

    2010-01-01

    Summary Les lésions radiques sont dues le plus souvent à des radio-isotopes utilisés dans l’industrie. L’explosion d’un réacteur nucléaire, les armes nucléaires ou une attaque terroriste constituent un risque d’afflux massif de victimes brûlées. Les radiations ionisantes occasionnent des brûlures thermiques, des syndromes d’irradiation aiguë avec pancytopénie et des signes cutanés retardés. Après une période de latence, des symptômes cutanés apparaissent et leur profondeur est proportionnelle à la dose reçue. Les protocoles habituels de réanimation des brûlés s’appliquent ici. Les soins aux irradiés nécessitent aussi une mesure de l’irradiation et une décontamination par des personnels entraînés. En cas de catastrophe nucléaire, la priorité est d’optimiser les structures existantes et de préserver les moyens pour les patients ayant la plus forte probabilité de survie. Après un accident nucléaire isolé, les difficultés dans les centres de brûlés sont l’évaluation de la profondeur et les techniques chirurgicales de couverture cutanée. La préparation des moyens médicaux et des centres de brûlés est nécessaire pour faire face à la prise en charge de ces brûlures différentes et complexes. PMID:21991218

  8. Evaluating SPP/APR Improvement Activities

    ERIC Educational Resources Information Center

    National Early Childhood Technical Assistance Center (NECTAC), 2009

    2009-01-01

    This document is intended to assist State Education Agency (SEA) and Lead Agency (LA) staff and technical assistance providers in designing a meaningful evaluation for the State Performance Plan (SPP)/Annual Performance Report (APR) improvement activities. It provides: (1) information about the relevance of evaluation in the context of improvement…

  9. Inactivation of aprE Gene in Bacillus subtilis 168 by Homologus Recombination

    PubMed Central

    Rabbani, Mohammed; Soleymani, Safoura; Sadeghi, Hamid Mir Mohammad; Soleimani, Narjes; Moazen, Fatemeh

    2014-01-01

    Background One of the most important producers of high quality industrial enzymes is the Gram-positive bacterium, Bacillus subtilis (B. Subtilis). One major limitation that hinders the wide application of B. subtilis is the secretion of high levels of extracellular proteases which degrade the secreted foreign proteins. In this study, homologus recombination technique was used to knock out its protease gene, aprE. Methods The internal segment of the pro-sequence of aprE gene of B. subtilis 168 with a length of 80 bps and its complementary sequence were synthesized and ligated into pUB110 at EcoR1 and XbaI restriction sites. Competent cells of B. subtilis 168 were prepared and transformed by electroporation using Bio Rad gene pulser as explained in the methods section. Transformants carrying the recombinant plasmid were selected for resistance to neomycin. The success of homologous recombination was checked by PCR amplification of the neomycin gene which was part of the vector and did not exist in the genome of B. subtilis 168. The protease activity was measured using the Protease Fluorescent Detection Kit based on the proteolytic hydrolysis of fluorescein isothiocyanate (FITC)–labeled casein-substrate. Results The results demonstrated that aprE gene would not be able to produce further active subtilisin E. The reduction of protease activity also confirmed the efficacy of the induced mutation in this gene. Conclusion It will therefore be a major challenge for future research to identify and modulate quality control systems of B. subtilis which limit the production of high quality protease- sensitive products such as lipase. PMID:25215183

  10. 12. Historic American Buildings Survey Arthur C. Haskell, Photographer Apr. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    12. Historic American Buildings Survey Arthur C. Haskell, Photographer Apr. 1, 1939 (l) INT.- STAIRWAY, 4th FLOOR, LOOKING SOUTH - M.I.T., Rogers Building, 491 Boylston Street, Boston, Suffolk County, MA

  11. 5. Historic American Buildings Survey Roger Sturtevant, Photographer Apr. 5, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. Historic American Buildings Survey Roger Sturtevant, Photographer Apr. 5, 1934 JACOB R. GIDDIS AND JOEL A. CUMBACK, MOUNTAIN VIEW CEMETERY, COLUMBIA - Grave Stones, Mountain View Cemetery, Bigler Street, Columbia, Tuolumne County, CA

  12. Revision of testing criteria for air cleaning unit of renovated APR-1000 and APR-1400 NPPS.

    PubMed

    Jeong, Seung-Young

    2011-07-01

    Designing Air Cleaning Units (ACU) of an Engineered Safety Feature and normal atmosphere clean-up system at the renovated APR-1000 and APR-1400 NPP, and fuel cycle facilities in Korea, is required to meet the standards of ASME AG-1 (1997), ASME N509/N510 (1989) and KEPIC-MH (2001) to enhance the removal efficiency of aerosols and particulates from the effluents. The revised ACU testing criteria are allowed to use alternative challenge agents of the dioctyl phthalate and Refrigerant-11 for in situ testing of high efficiency particulate air filters and adsorption banks. The operability testing time of engineered safety feature (ESF) trains was changed from 10 h to 15 min. The activated carbon in adsorption banks should undergo laboratory tests at a temperature of 30 °C and relative humidity 95 %. The removal criteria of methyl iodide should be over 99.5 % for ESF and 99 % for normal systems. This paper provides the background of the changed criteria for designing and testing of the ACU system in nuclear facilities.

  13. Implementation and Analysis for APR1400 Soft Control System

    SciTech Connect

    2015-07-01

    Due to the rapid advancement of digital technology, the definite technical advantages of digital control system compared to analog control system are accelerating the implementation of advanced distributed digital control system in the nuclear power plant. One of the major advantages of digital control system is the capability of Soft Control System. The design of Soft Control System for Advanced Power Reactor 1400 (APR1400) plant of Man-Machine Interface System (MMIS) is based on full digital technologies to enhance reliability, operability and maintainability. Computer-based compact workstation has been adopted in the APR1400 Main Control Room (MCR) to provide convenient working environment. This paper introduces the approaches and methodologies of Soft Control System for the Advanced Control Room (ACR). This paper also explains major design features for operation and display of the Soft Control System and its implementation to cope with regulatory requirements. (authors)

  14. Gamma irradiation effect on the enzymatic activities of horseradish and apple peroxidases

    NASA Astrophysics Data System (ADS)

    Constantinovici, M.; Oancea, D.; Zaharescu, T.

    2009-01-01

    The behavior at low-dose exposure (0.033-0.4 kGy) of horseradish peroxidase (HRP) and of two different purified fractions of apple (Jonathan cultivar) peroxidases (named APR 1S and APR 2S) was studied. The HRP solutions were added with either 0.32 M fructose or glucose in order to study their effect on enzymes activity response under γ ( 137Cs, dose rate 0.4 kGy/h) irradiation. The obtained results showed similar behavior between HRP-sugar-added solution and apple fraction with higher oligosaccharides content (APR 2S) undergoing low-dose treatment. The same pattern was observed between unglycosylated HRP and APR 1S with lower oligosaccharides content. These similarities gave us the possibility to conclude that the presence of oligosaccharides, in more or less quantities, influences in the same way the peroxidases activity, from different plant species, exposed to γ irradiation.

  15. Review of APR+ Level 2 PSA. Revision 2

    SciTech Connect

    Lehner, John R.; Mubayi, Vinod; Pratt, W. Trevor; Kim, Do Sam; Cho, Yong Jin; Cho, Sang Jin; Kim, In Goo

    2012-02-17

    Brookhaven National Laboratory (BNL) assisted the Korea Institute of Nuclear Safety (KINS) in reviewing the Level 2 Probabilistic Safety Assessment (PSA) of the APR+ Advanced Pressurized Water Reactor (PWR) prepared by the Korea Hydro & Nuclear Power Co., Ltd (KHNP) and KEPCO Engineering & Construction Co., Inc. (KEPCO-E&C). The work described in this report involves a review of the APR+ Level 2 PSA submittal [Ref. 1]. The PSA and, therefore, the review is limited to consideration of accidents initiated by internal events. As part of the review process, the review team also developed three sets of Requests for Additional Information (RAIs). These RAIs were provided to KHNP and KEPCO-E&C for their evaluation and response. This final detailed report documents the review findings for each technical element of the PSA and includes consideration of all of the RAIs made by the reviewers as well as the associated responses. This final report was preceded by an interim report [Ref. 2] that focused on identifying important issues regarding the PSA. In addition, a final meeting on the project was held at BNL on November 21-22, 2011, where BNL and KINS reviewers discussed their preliminary review findings with KHNP and KEPCO-E&C staffs. Additional information obtained during this final meeting was also used to inform the review findings of this final report. The review focused not only on the robustness of the APR+ design to withstand severe accidents, but also on the capability and acceptability of the Level 2 PSA in terms of level of detail and completeness. The Korean nuclear regulatory authorities will decide whether the PSA is acceptable and the BNL review team is providing its comments for KINS consideration. Section 2.0 provides the basis for the BNL review. Section 3.0 presents the review of each technical element of the PSA. Conclusions and a summary are presented in Section 4.0. Section 5.0 contains the references.

  16. FORMAL REPORT NO. 1, 1 APR-30 SEP 65.

    DTIC Science & Technology

    PROTON BEAMS), (*RADIATION EFFECTS, RADIOBIOLOGY, PRIMATES, MICE , EYE, BRAIN, WHOLE BODY IRRADIATION, RADIATION DOSAGE, DOSIMETERS, ROTATION, EXPOSURE(PHYSIOLOGY), TEST EQUIPMENT, INSTRUMENTATION, CYCLOTRONS.

  17. 53. Neg. No. F69, Apr 21, 1930, EXTERIOROFFICE BUILDING, WEST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    53. Neg. No. F-69, Apr 21, 1930, EXTERIOR-OFFICE BUILDING, WEST (FRONT) AND NORTH SIDES, OPENING DAY - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

  18. 48 CFR 1552.235-76 - Treatment of Confidential Business Information (APR 1996).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ...)(APR 1996) (a) The Project Officer (PO) or his/her designee, after a written determination by the... General Counsel for Information Law or his/her designee; and (iii) return the CBI to the PO or...

  19. 82. Neg. No. F66A, Apr 13, 1930, INTERIORASSEMBLY BUILDING, TRIM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    82. Neg. No. F-66A, Apr 13, 1930, INTERIOR-ASSEMBLY BUILDING, TRIM LINE AND GLASS DEPARTMENTS - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

  20. 83. Neg. No. F53, Apr 13, 1930, INTERIORASSEMBLY BUILDING, BACK ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    83. Neg. No. F-53, Apr 13, 1930, INTERIOR-ASSEMBLY BUILDING, BACK TRIM LINE - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

  1. 15 CFR 782.1 - Overview of reporting requirements under the APR.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL... (see § 782.5 of the APR). In addition, forms may be downloaded from the Internet at http://www.ap.gov....

  2. 15 CFR 782.5 - Where to obtain APR report forms.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL REGULATIONS GENERAL... forms required by the APR may be downloaded from the Internet at http://www.ap.gov. You also may...

  3. 15 CFR 782.1 - Overview of reporting requirements under the APR.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL... (see § 782.5 of the APR). In addition, forms may be downloaded from the Internet at http://www.ap.gov....

  4. 15 CFR 782.5 - Where to obtain APR report forms.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL REGULATIONS GENERAL... forms required by the APR may be downloaded from the Internet at http://www.ap.gov. You also may...

  5. 15 CFR 782.5 - Where to obtain APR report forms.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL REGULATIONS GENERAL... forms required by the APR may be downloaded from the Internet at http://www.ap.gov. You also may...

  6. 15 CFR 782.5 - Where to obtain APR report forms.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL REGULATIONS GENERAL... forms required by the APR may be downloaded from the Internet at http://www.ap.gov. You also may...

  7. 15 CFR 782.1 - Overview of reporting requirements under the APR.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL... (see § 782.5 of the APR). In addition, forms may be downloaded from the Internet at http://www.ap.gov....

  8. 15 CFR 782.1 - Overview of reporting requirements under the APR.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL... (see § 782.5 of the APR). In addition, forms may be downloaded from the Internet at http://www.ap.gov....

  9. 15 CFR 782.1 - Overview of reporting requirements under the APR.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL... (see § 782.5 of the APR). In addition, forms may be downloaded from the Internet at http://www.ap.gov....

  10. 15 CFR 782.5 - Where to obtain APR report forms.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL REGULATIONS GENERAL... forms required by the APR may be downloaded from the Internet at http://www.ap.gov. You also may...

  11. 86. Neg. No. F64, Apr 13, 1930, INTERIORASSEMBLY BUILDING, BODY ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    86. Neg. No. F-64, Apr 13, 1930, INTERIOR-ASSEMBLY BUILDING, BODY STORAGE CONVEYOR - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

  12. 79. Neg. No. F61A, Apr 13, 1930, INTERIORASSEMBLY BUILDING, BODY ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    79. Neg. No. F-61A, Apr 13, 1930, INTERIOR-ASSEMBLY BUILDING, BODY CONSTRUCTION - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

  13. 85. Neg. No. F51, Apr 13, 1930, INTERIORASSEMBLY BUILDING, BODY ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    85. Neg. No. F-51, Apr 13, 1930, INTERIOR-ASSEMBLY BUILDING, BODY AND CUSHION LINE - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

  14. Fuel assembly design for APR1400 with low CBC

    SciTech Connect

    Hah, Chang Joo

    2015-04-29

    APR 1400 is a PWR (Pressurized Water Reactor) with rated power of 3983 MWth and 241 assemblies. Recently, demand for extremely longer cycle up to 24 months is increasing with challenge of higher critical boron concentration (CBC). In this paper, assembly design method of selecting Gd-rods is introduced to reduce CBC. The purpose of the method is to lower the critical boron concentration of the preliminary core loading pattern (PLP), and consequently to achieve more negative or less positive moderator temperature coefficient (MTC). In this method, both the ratio of the number of low-Gd rod to the number of high-Gd rod (r) and assembly average Gd wt% (w) are the decision variables. The target function is the amount of soluble boron concentration reduction, which can be converted to Δk{sub TARGET}. A set of new designed fuel assembly satisfies an objective function, min [f=∑{sub i}(Δk{sub FA}−Δk{sub i})], and enables a final loading pattern to reach a target CBC. The constraints required to determine a set of Δk are physically realizable pair, (r,w), and the sum of Δk of new designed assemblies as close to Δk{sub TARGET} as possible. New Gd-bearing assemblies selected based on valid pairs of (r,w) are replaced with existing assemblies in a PLP. This design methodology is applied to Shin-Kori Unit 3 Cycle 1 used as a reference model. CASMO-3/MASTER code is used for depletion calculation. CASMO-3/MASTER calculations with new designed assemblies produce lower CBC than the expected CBC, proving that the proposed method works successful.

  15. Reliability enhancement of APR + diverse protection system regarding common cause failures

    SciTech Connect

    Oh, Y. G.; Kim, Y. M.; Yim, H. S.; Lee, S. J.

    2012-07-01

    The Advanced Power Reactor Plus (APR +) nuclear power plant design has been developed on the basis of the APR1400 (Advanced Power Reactor 1400 MWe) to further enhance safety and economics. For the mitigation of Anticipated Transients Without Scram (ATWS) as well as Common Cause Failures (CCF) within the Plant Protection System (PPS) and the Emergency Safety Feature - Component Control System (ESF-CCS), several design improvement features have been implemented for the Diverse Protection System (DPS) of the APR + plant. As compared to the APR1400 DPS design, the APR + DPS has been designed to provide the Safety Injection Actuation Signal (SIAS) considering a large break LOCA accident concurrent with the CCF. Additionally several design improvement features, such as channel structure with redundant processing modules, and changes of system communication methods and auto-system test methods, are introduced to enhance the functional reliability of the DPS. Therefore, it is expected that the APR + DPS can provide an enhanced safety and reliability regarding possible CCF in the safety-grade I and C systems as well as the DPS itself. (authors)

  16. Assistant Personal Robot (APR): Conception and Application of a Tele-Operated Assisted Living Robot.

    PubMed

    Clotet, Eduard; Martínez, Dani; Moreno, Javier; Tresanchez, Marcel; Palacín, Jordi

    2016-04-28

    This paper presents the technical description, mechanical design, electronic components, software implementation and possible applications of a tele-operated mobile robot designed as an assisted living tool. This robotic concept has been named Assistant Personal Robot (or APR for short) and has been designed as a remotely telecontrolled robotic platform built to provide social and assistive services to elderly people and those with impaired mobility. The APR features a fast high-mobility motion system adapted for tele-operation in plain indoor areas, which incorporates a high-priority collision avoidance procedure. This paper presents the mechanical architecture, electrical fundaments and software implementation required in order to develop the main functionalities of an assistive robot. The APR uses a tablet in order to implement the basic peer-to-peer videoconference and tele-operation control combined with a tactile graphic user interface. The paper also presents the development of some applications proposed in the framework of an assisted living robot.

  17. Molecular genetic analysis of Dichelobacter nodosus proteases AprV2/B2, AprV5/B5 and BprV/B in clinical material from European sheep flocks.

    PubMed

    Stäuble, Anna; Steiner, Adrian; Normand, Lea; Kuhnert, Peter; Frey, Joachim

    2014-01-10

    Dichelobacter nodosus, the etiological agent of ovine footrot, exists both as virulent and as benign strains, which differ in virulence mainly due to subtle differences in the three subtilisin-like proteases AprV2, AprV5 and BprV found in virulent, and AprB2, AprB5 and BprB in benign strains of D. nodosus. Our objective was a molecular genetic epidemiological analysis of the genes of these proteases by direct sequence analysis from clinical material of sheep from herds with and without history of footrot from 4 different European countries. The data reveal the two proteases known as virulent AprV2 and benign AprB2 to correlate fully to the clinical status of the individuals or the footrot history of the herd. In samples taken from affected herds, the aprV2 gene was found as a single allele whereas in samples from unaffected herds several alleles with minor modifications of the aprB2 gene were detected. The different alleles of aprB2 were related to the herds. The aprV5 and aprB5 genes were found in the form of several alleles scattered without distinction between affected and non-affected herds. However, all different alleles of aprV5 and aprB5 encode the same amino acid sequences, indicating the existence of a single protease isoenzyme 5 in both benign and virulent strains. The genes of the basic proteases BprV and BprB also exist as various alleles. However, differences found in samples from affected versus non-affected herds do not reflect the currently known epitopes that are attributed to differences in biochemical activity. The data of the study confirm the prominent role of AprV2 in the virulence of D. nodosus and shed a new light on the presence of the other protease genes and their allelic variants in clinical samples.

  18. Anti-inflammatory and anti-proliferative effect of herbal medicines (APR) in RAW264.7 cells

    PubMed Central

    CHOI, HAN-SEOK; SEO, HYE SOOK; KIM, SOON RE; CHOI, YOUN KYUNG; SHIN, YONG-CHEOL; KO, SEONG-GYU

    2014-01-01

    The objective of the present study was to analyze the effect of a mixture of medicinal plants [Angelica gigas Nakai, Panax ginseng and Rhus verniciflua Stokes (APR)] on lipopolysaccharide (LPS)-induced inflammatory responses in the murine macrophage cell line RAW264.7. Cells were treated with APR and LPS at various concentrations and indicated times. WST assay, trypan blue assay and quantification of activated cells demonstrated that APR suppressed cell proliferation in a dose-dependent manner. APR induced G1 cell cycle arrest and inhibited the LPS-induced phosphorylation of protein kinase B (AKT), extracellular signal-regulated kinase (ERK), mitogen-activated protein kinase (p38) and necrosis factor κB (NF-κB). APR also suppressed nitric oxide synthase isoform (iNOS) and prostaglandin endoperoxide synthase 2 (Cox-2) messenger ribonucleic acid (mRNA) expression induced by LPS. Furthermore, APR decreased LPS-induced intracellular reactive oxygen species (ROS) levels, mitochondrial membrane potential, as well as induced PARP and caspase-3 cleavage, suggesting that APR causes apoptosis. In conclusion, the present study indicated that APR may be advantageous in treating inflammatory disease. PMID:24626965

  19. [Food irradiation].

    PubMed

    Migdał, W

    1995-01-01

    A worldwide standard on food irradiation was adopted in 1983 by Codex Alimentarius Commission of the Joint Food Standard Programme of the Food and Agriculture Organization (FAO) of the United Nations and the World Health Organization (WHO). As a result, 41 countries have approved the use of irradiation for treating one or more food items and the number is increasing. Generally, irradiation is used to: food loses, food spoilage, disinfestation, safety and hygiene. The number of countries which use irradiation for processing food for commercial purposes has been increasing steadily from 19 in 1987 to 33 today. In the frames of the national programme on the application of irradiation for food preservation and hygienization an experimental plant for electron beam processing has been established in Institute of Nuclear Chemistry and Technology. The plant is equipped with a small research accelerator Pilot (19MeV, 1 kW) and an industrial unit Elektronika (10MeV, 10 kW). On the basis of the research there were performed at different scientific institutions in Poland, health authorities have issued permission for irradiation for: spices, garlic, onions, mushrooms, potatoes, dry mushrooms and vegetables.

  20. Tissue irradiator

    DOEpatents

    Hungate, F.P.; Riemath, W.F.; Bunnell, L.R.

    1975-12-16

    A tissue irradiator is provided for the in-vivo irradiation of body tissue. The irradiator comprises a radiation source material contained and completely encapsulated within vitreous carbon. An embodiment for use as an in- vivo blood irradiator comprises a cylindrical body having an axial bore therethrough. A radioisotope is contained within a first portion of vitreous carbon cylindrically surrounding the axial bore, and a containment portion of vitreous carbon surrounds the radioisotope containing portion, the two portions of vitreous carbon being integrally formed as a single unit. Connecting means are provided at each end of the cylindrical body to permit connections to blood- carrying vessels and to provide for passage of blood through the bore. In a preferred embodiment, the radioisotope is thulium-170 which is present in the irradiator in the form of thulium oxide. A method of producing the preferred blood irradiator is also provided, whereby nonradioactive thulium-169 is dispersed within a polyfurfuryl alcohol resin which is carbonized and fired to form the integral vitreous carbon body and the device is activated by neutron bombardment of the thulium-169 to produce the beta-emitting thulium-170.

  1. 14 CFR Appendix H to Part 23 - Installation of An Automatic Power Reserve (APR) System

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... failure, transmit signals, actuate fuel controls or power levers on operating engines, including power... power lever position; and (c) That shown to be free of hazardous engine response characteristics when...; (3) Prevent deactivation of the APR by manual adjustment of the power levers following an...

  2. 14 CFR Appendix H to Part 23 - Installation of An Automatic Power Reserve (APR) System

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... failure, transmit signals, actuate fuel controls or power levers on operating engines, including power... power lever position; and (c) That shown to be free of hazardous engine response characteristics when...; (3) Prevent deactivation of the APR by manual adjustment of the power levers following an...

  3. 14 CFR Appendix H to Part 23 - Installation of An Automatic Power Reserve (APR) System

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... failure, transmit signals, actuate fuel controls or power levers on operating engines, including power... power lever position; and (c) That shown to be free of hazardous engine response characteristics when...; (3) Prevent deactivation of the APR by manual adjustment of the power levers following an...

  4. 14 CFR Appendix H to Part 23 - Installation of An Automatic Power Reserve (APR) System

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... failure, transmit signals, actuate fuel controls or power levers on operating engines, including power... power lever position; and (c) That shown to be free of hazardous engine response characteristics when...; (3) Prevent deactivation of the APR by manual adjustment of the power levers following an...

  5. 48 CFR 1552.235-79 - Release of contractor confidential business information (APR 1996).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Release of contractor confidential business information (APR 1996). 1552.235-79 Section 1552.235-79 Federal Acquisition Regulations... pursuant to a request filed under the Freedom of Information Act. (f) The Contractor agrees to include...

  6. 54. Neg. No. F110P, Apr 24, 1931, EXTERIORPRESSED STEEL BUILDING, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    54. Neg. No. F-110P, Apr 24, 1931, EXTERIOR-PRESSED STEEL BUILDING, NORTH AND EAST SIDES, WAREHOUSE IN BACKGROUND, RAILROAD SPUR IN FOREGROUND, BONDERITE TANK AT LEFT - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

  7. 14 CFR Appendix H to Part 23 - Installation of An Automatic Power Reserve (APR) System

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... failure, transmit signals, actuate fuel controls or power levers on operating engines, including power... power lever position; and (c) That shown to be free of hazardous engine response characteristics when...; (3) Prevent deactivation of the APR by manual adjustment of the power levers following an...

  8. Privacy Impact Assessment for the TRIO Programs Annual Performance Report (APR) System

    ERIC Educational Resources Information Center

    US Department of Education, 2008

    2008-01-01

    The TRIO Programs Annual Performance Report (APR) System collects individual student records on individuals served by the following Federal TRIO Programs: Upward Bound (which includes regular Upward Bound (UB), Upward Bound Math-Science (UBMS), and Veterans Upward Bound (VUB)); Student Support Services (SSS); and the Ronald E. McNair Post…

  9. Student Access to Advanced Placement[R] (AP[R]) Coursework: Principals' Beliefs and Practices

    ERIC Educational Resources Information Center

    Wood, Steven M.

    2010-01-01

    Advanced Placement[R] (AP[R]) courses provide high school students an opportunity to be exposed to the rigors of college while they are still in high school. Since school policies play a role in the opportunities for students to pursue these courses, educational leaders must be aware of the ways in which their personal beliefs and school practices…

  10. Irradiation subassembly

    DOEpatents

    Seim, O.S.; Filewicz, E.C.; Hutter, E.

    1973-10-23

    An irradiation subassembly for use in a nuclear reactor is described which includes a bundle of slender elongated irradiation -capsules or fuel elements enclosed by a coolant tube and having yieldable retaining liner between the irradiation capsules and the coolant tube. For a hexagonal bundle surrounded by a hexagonal tube the yieldable retaining liner may consist either of six segments corresponding to the six sides of the tube or three angular segments each corresponding in two adjacent sides of the tube. The sides of adjacent segments abut and are so cut that metal-tometal contact is retained when the volume enclosed by the retaining liner is varied and Springs are provided for urging the segments toward the center of the tube to hold the capsules in a closely packed configuration. (Official Gazette)

  11. Prise en compte d'un couplage fin neutronique-thermique dans les calculs d'assemblage pour les reacteurs a eau pressurisee

    NASA Astrophysics Data System (ADS)

    Greiner, Nathan

    Core simulations for Pressurized Water Reactors (PWR) is insured by a set of computer codes which allows, under certain assumptions, to approximate the physical quantities of interest, such as the effective multiplication factor or the power or temperature distributions. The neutronics calculation scheme relies on three great steps : -- the production of an isotopic cross-sections library ; -- the production of a reactor database through the lattice calculation ; -- the full-core calculation. In the lattice calculation, in which Boltzmann's transport equation is solved over an assembly geometry, the temperature distribution is uniform and constant during irradiation. This represents a set of approximations since, on the one hand, the temperature distribution in the assembly is not uniform (strong temperature gradients in the fuel pins, discrepancies between the fuel pins) and on the other hand, irradiation causes the thermal properties of the pins to change, which modifies the temperature distribution. Our work aims at implementing and introducing a neutronics-thermomechanics coupling into the lattice calculation to finely discretize the temperature distribution and to study its effects. To perform the study, CEA (Commissariat a l'Energie Atomique et aux Energies Alternatives) lattice code APOLLO2 was used for neutronics and EDF (Electricite De France) code C3THER was used for the thermal calculations. We show very small effects of the pin-scaled coupling when comparing the use of a temperature profile with the use of an uniform temperature over UOX-type and MOX-type fuels. We next investigate the thermal feedback using an assembly-scaled coupling taking into account the presence of large water gaps on an UOX-type assembly at burnup 0. We show the very small impact on the calculation of the hot spot factor. Finally, the coupling is introduced into the isotopic depletion calculation and we show that reactivity and isotopic number densities deviations remain small

  12. Irradiated foods

    MedlinePlus

    ... it reduces the risk of food poisoning . Food irradiation is used in many countries. It was first approved in the U.S. to prevent sprouts on white potatoes, and to control insects on wheat and in certain spices and seasonings.

  13. Categorizing Ice Crystals Using Airborne APR-2 and HVPS Observations during GCPEx

    NASA Astrophysics Data System (ADS)

    Martinez, M., III; Bennartz, R.; Turk, F. J.; Tanelli, S.; Sy, O. O.; Bansemer, A.; Kuo, K. S.

    2014-12-01

    Current and planned millimeter-wave passive and active satellite sensors are proposed for future low Earth-orbiting satellite platforms. For accurate modeling and sensor simulation of ice clouds at these wavelengths, realistic particle shapes and size distributions (PSD) need to be used. During the Jan-Feb 2012 Global Precipitation Measurement (GPM) Cold Season Precipitation Experiment (GCPEx) near Toronto, Canada, the Jet Propulsion Laboratory (JPL) dual-frequency (Ku/Ka-band) Airborne Precipitation Radar (APR-2) flew onboard the NASA DC-8 aircraft. Coordinated flights were carried out with the Univ. of North Dakota Citation aircraft carrying the High Volume Precipitation Spectrometer (HVPS-3), to collect cloud PSD and particle imagery. Selected flights enabled collection of coincident sampling volumes from the APR-2 and the HVPS. This unique dataset enables the scattering properties of the frozen hydrometeors to be modeled using the HVPS-provided particle distributions, and compared with APR-2 observations. The wide variety of fractal-like particle shapes measured in the HVPS data were separated into size bins and presented as 2 dimensional histograms with bins defined by Aspect (As) and Area (Ar) ratio. Individual histograms were previously characterized by the mean As and Ar values, ignoring the preferential linear trend between As and Ar visible for data points within most particle sizes. To facilitate the scattering models, we attempted to partition particles by shape within four size-invariant As and Ar categories. The four unique PSD, created by particle shape segregation, were then used to forward model the Ku and Ka- band radar reflectivities to locate the particle characteristics that provided the best agreement with actual APR-2 observations. In future work, these PSD will be used for passive microwave satellite sensor simulations of cold season precipitation and compared to actual satellite observations.

  14. Assistant Personal Robot (APR): Conception and Application of a Tele-Operated Assisted Living Robot

    PubMed Central

    Clotet, Eduard; Martínez, Dani; Moreno, Javier; Tresanchez, Marcel; Palacín, Jordi

    2016-01-01

    This paper presents the technical description, mechanical design, electronic components, software implementation and possible applications of a tele-operated mobile robot designed as an assisted living tool. This robotic concept has been named Assistant Personal Robot (or APR for short) and has been designed as a remotely telecontrolled robotic platform built to provide social and assistive services to elderly people and those with impaired mobility. The APR features a fast high-mobility motion system adapted for tele-operation in plain indoor areas, which incorporates a high-priority collision avoidance procedure. This paper presents the mechanical architecture, electrical fundaments and software implementation required in order to develop the main functionalities of an assistive robot. The APR uses a tablet in order to implement the basic peer-to-peer videoconference and tele-operation control combined with a tactile graphic user interface. The paper also presents the development of some applications proposed in the framework of an assisted living robot. PMID:27136552

  15. The Alberta Pregnancy Outcomes and Nutrition (APrON) cohort study: rationale and methods.

    PubMed

    Kaplan, Bonnie J; Giesbrecht, Gerald F; Leung, Brenda M Y; Field, Catherine J; Dewey, Deborah; Bell, Rhonda C; Manca, Donna P; O'Beirne, Maeve; Johnston, David W; Pop, Victor J; Singhal, Nalini; Gagnon, Lisa; Bernier, Francois P; Eliasziw, Misha; McCargar, Linda J; Kooistra, Libbe; Farmer, Anna; Cantell, Marja; Goonewardene, Laki; Casey, Linda M; Letourneau, Nicole; Martin, Jonathan W

    2014-01-01

    The Alberta Pregnancy Outcomes and Nutrition (APrON) study is an ongoing prospective cohort study that recruits pregnant women early in pregnancy and, as of 2012, is following up their infants to 3 years of age. It has currently enrolled approximately 5000 Canadians (2000 pregnant women, their offspring and many of their partners). The primary aims of the APrON study were to determine the relationships between maternal nutrient intake and status, before, during and after gestation, and (1) maternal mood; (2) birth and obstetric outcomes; and (3) infant neurodevelopment. We have collected comprehensive maternal nutrition, anthropometric, biological and mental health data at multiple points in the pregnancy and the post-partum period, as well as obstetrical, birth, health and neurodevelopmental outcomes of these pregnancies. The study continues to follow the infants through to 36 months of age. The current report describes the study design and methods, and findings of some pilot work. The APrON study is a significant resource with opportunities for collaboration.

  16. Phytosanitary Irradiation

    PubMed Central

    Hallman, Guy J.; Blackburn, Carl M.

    2016-01-01

    Phytosanitary treatments disinfest traded commodities of potential quarantine pests. Phytosanitary irradiation (PI) treatments use ionizing radiation to accomplish this, and, since their international commercial debut in 2004, the use of this technology has increased by ~10% annually. Generic PI treatments (one dose is used for a group of pests and/or commodities, although not all have been tested for efficacy) are used in virtually all commercial PI treatments, and new generic PI doses are proposed, such as 300 Gy, for all insects except pupae and adult Lepidoptera (moths). Fresh fruits and vegetables tolerate PI better than any other broadly used treatment. Advances that would help facilitate the use of PI include streamlining the approval process, making the technology more accessible to potential users, lowering doses and broadening their coverage, and solving potential issues related to factors that might affect efficacy. PMID:28231103

  17. Après-Coup in French Psychoanalysis: The Long Afterlife of Nachträglichkeit: The First Hundred Years, 1893 to 1993.

    PubMed

    House, Jonathan; Slotnick, Julie

    2015-10-01

    Après-coup finds its origins in Freud's earliest psychoanalytic writings, but it was only half a century ago that French psychoanalysts rediscovered, clarified, and developed the concept and so brought it recognition as an essential Freudian concept. Because the history of après-coup is embedded in the French reading of Freud, this article will give an account of that reading in relation to après-coup.

  18. The X-ray crystal structure of APR-B, an atypical adenosine 5'-phosphosulfate reductase from Physcomitrella patens.

    PubMed

    Stevenson, Clare E M; Hughes, Richard K; McManus, Michael T; Lawson, David M; Kopriva, Stanislav

    2013-11-15

    Sulfonucleotide reductases catalyse the first reductive step of sulfate assimilation. Their substrate specificities generally correlate with the requirement for a [Fe4S4] cluster, where adenosine 5'-phosphosulfate (APS) reductases possess a cluster and 3'-phosphoadenosine 5'-phosphosulfate reductases do not. The exception is the APR-B isoform of APS reductase from the moss Physcomitrella patens, which lacks a cluster. The crystal structure of APR-B, the first for a plant sulfonucleotide reductase, is consistent with a preference for APS. Structural conservation with bacterial APS reductase rules out a structural role for the cluster, but supports the contention that it enhances the activity of conventional APS reductases.

  19. New tools for NTD vaccines: A case study of quality control assays for product development of the human hookworm vaccine Na-APR-1M74.

    PubMed

    Pearson, Mark S; Jariwala, Amar R; Abbenante, Giovanni; Plieskatt, Jordan; Wilson, David; Bottazzi, Maria Elena; Hotez, Peter J; Keegan, Brian; Bethony, Jeffrey M; Loukas, Alex

    2015-01-01

    Na-APR-1(M74) is an aspartic protease that is rendered enzymatically inactive by site-directed mutagenesis and is a candidate antigen component in the Human Hookworm Vaccine. The mutant protease exerts vaccine efficacy by inducing antibodies that neutralize the enzymatic activity of wild type enzyme (Na-APR-1wt) in the gut of the hookworm, thereby depriving the worm of its ability to digest its blood meal. Previously, canines immunized with Na-APR-1(M74) and challenged with Ancylostoma caninum were partially protected against hookworm challenge infection, especially from the loss in hemoglobin observed in control canines and canine immunoglobulin (Ig) G raised against Na-APR-1 was shown to inhibit the enzymatic activity of Na-APR-1 wt in vitro, thereby providing proof of concept of Na-APR-1(M74) as a vaccine antigen. The mutated version, Na-APR-1(M74), was then expressed at the cGMP level using a Nicotiana benthamiana expression system (Fraunhofer, CMB, Delaware, MD), formulated with Alhydrogel®, and used to immunize mice in a dose-ranging study to explore the enzyme-neutralizing capacity of the resulting anti- Na-APR-1(M74) IgG. As little as 0.99 μg of recombinant Na-APR-1(M74) could induce anti Na-APR-1(M74) IgG in mice that were capable of inhibiting Na-APR-1w t-mediated digestion of a peptide substrate by 89%. In the absence of enzymatic activity of Na-APR-1(M74) as a surrogate marker of protein functionality, we developed an assay based on the binding of a quenched fluorescence-labeled inhibitor of aspartic proteases, BODIPY-FL pepstatin A (BDP). Binding of BDP in the active site of Na-APR-1 wt was demonstrated by inhibition of enzymatic activity, and competitive binding with unlabelled pepstatin A. BDP also bound to Na-APR-1(M74) which was assessed by fluorescence polarization, but with an ∼ 50-fold reduction in the dissociation constant. Taken together, these assays comprise a "toolbox" that could be useful for the analyses of Na-APR-1(M74) as it

  20. New tools for NTD vaccines: A case study of quality control assays for product development of the human hookworm vaccine Na-APR-1M74

    PubMed Central

    Pearson, Mark S; Jariwala, Amar R; Abbenante, Giovanni; Plieskatt, Jordan; Wilson, David; Bottazzi, Maria Elena; Hotez, Peter J; Keegan, Brian; Bethony, Jeffrey M; Loukas, Alex

    2015-01-01

    Na-APR-1M74 is an aspartic protease that is rendered enzymatically inactive by site-directed mutagenesis and is a candidate antigen component in the Human Hookworm Vaccine. The mutant protease exerts vaccine efficacy by inducing antibodies that neutralize the enzymatic activity of wild type enzyme (Na-APR-1wt) in the gut of the hookworm, thereby depriving the worm of its ability to digest its blood meal. Previously, canines immunized with Na-APR-1M74 and challenged with Ancylostoma caninum were partially protected against hookworm challenge infection, especially from the loss in hemoglobin observed in control canines and canine immunoglobulin (Ig) G raised against Na-APR-1 was shown to inhibit the enzymatic activity of Na-APR-1wt in vitro, thereby providing proof of concept of Na-APR-1M74 as a vaccine antigen. The mutated version, Na-APR-1M74, was then expressed at the cGMP level using a Nicotiana benthamiana expression system (Fraunhofer, CMB, Delaware, MD), formulated with Alhydrogel®, and used to immunize mice in a dose-ranging study to explore the enzyme-neutralizing capacity of the resulting anti- Na-APR-1M74 IgG. As little as 0.99 μg of recombinant Na-APR-1M74 could induce anti Na-APR-1M74 IgG in mice that were capable of inhibiting Na-APR-1wt-mediated digestion of a peptide substrate by 89%. In the absence of enzymatic activity of Na-APR-1M74 as a surrogate marker of protein functionality, we developed an assay based on the binding of a quenched fluorescence-labeled inhibitor of aspartic proteases, BODIPY-FL pepstatin A (BDP). Binding of BDP in the active site of Na-APR-1wt was demonstrated by inhibition of enzymatic activity, and competitive binding with unlabelled pepstatin A. BDP also bound to Na-APR-1M74 which was assessed by fluorescence polarization, but with an ∼50-fold reduction in the dissociation constant. Taken together, these assays comprise a “toolbox” that could be useful for the analyses of Na-APR-1M74 as it proceeds through the

  1. Molecular analysis of the distribution and phylogeny of dissimilatory adenosine-5'-phosphosulfate reductase-encoding genes (aprBA) among sulfur-oxidizing prokaryotes.

    PubMed

    Meyer, Birte; Kuever, Jan

    2007-10-01

    Dissimilatory adenosine-5'-phosphosulfate (APS) reductase (AprBA) is a key enzyme of the dissimilatory sulfate-reduction pathway. Homologues have been found in photo- and chemotrophic sulfur-oxidizing prokaryotes (SOP), in which they are postulated to operate in the reverse direction, oxidizing sulfite to APS. Newly developed PCR assays allowed the amplification of 92-93 % (2.1-2.3 kb) of the APS reductase locus aprBA. PCR-based screening of 116 taxonomically divergent SOP reference strains revealed a distribution of aprBA restricted to photo- and chemotrophs with strict anaerobic or at least facultative anaerobic lifestyles, including Chlorobiaceae, Chromatiaceae, Thiobacillus, Thiothrix and invertebrate symbionts. In the AprBA-based tree, the SOP diverge into two distantly related phylogenetic lineages, Apr lineages I and II, with the proteins of lineage II (Chlorobiaceae and others) in closer affiliation to the enzymes of the sulfate-reducing prokaryotes (SRP). This clustering is discordant with the dissimilatory sulfite reductase (DsrAB) phylogeny and indicates putative lateral aprBA gene transfer from SRP to the respective SOB lineages. In support of lateral gene transfer (LGT), several beta- and gammaproteobacterial species harbour both aprBA homologues, the DsrAB-congruent 'authentic' and the SRP-related, LGT-derived gene loci, while some relatives possess exclusively the SRP-related apr genes as a possible result of resident gene displacement by the xenologue. The two-gene state might be an intermediate in the replacement of the resident essential gene. Collected genome data demonstrate the correlation between the AprBA tree topology and the composition/arrangement of the apr gene loci (occurrence of qmoABC or aprM genes) from SRP and SOP of lineages I and II. The putative functional role of the SRP-related APS reductases in photo- and chemotrophic SOP is discussed.

  2. Use of Irradiated Foods

    NASA Technical Reports Server (NTRS)

    Brynjolfsson, A.

    1985-01-01

    The safety of irradiated foods is reviewed. Guidelines and regulations for processing irradiated foods are considered. The radiolytic products formed in food when it is irradiated and its wholesomeness is discussed. It is concluded that food irradiation processing is not a panacea for all problems in food processing but when properly used will serve the space station well.

  3. Response Time Analysis and Test of Protection System Instrument Channels for APR1400 and OPR1000

    SciTech Connect

    Lee, Chang Jae; Han, Seung; Yun, Jae Hee; Baek, Seung Min; Lee, Sang Jeong

    2015-07-01

    Safety limits are required to maintain the integrity of physical barriers designed to prevent the uncontrolled release of radioactive materials in nuclear power plants. The safety analysis establishes two critical constraints that include an analytical limit in terms of a measured or calculated variable, and a specific time after the analytical limit is reached to begin protective action. Keeping with the nuclear regulations and industry standards, satisfying these two requirements will ensure that the safety limit will not be exceeded during the design basis event, either an anticipated operational occurrence or a postulated accident. Various studies on the setpoint determination methodology for the safety-related instrumentation have been actively performed to ensure that the requirement of the analytical limit is satisfied. In particular, the protection setpoint methodology for the advanced power reactor 1400 (APP1400) and the optimized power reactor 1000 (OPR1000) has been recently developed to cover both the design basis event and the beyond design basis event. The developed setpoint methodology has also been quantitatively validated using specific computer programs and setpoint calculations. However, the safety of nuclear power plants cannot be fully guaranteed by satisfying the requirement of the analytical limit. In spite of the response time verification requirements of nuclear regulations and industry standards, it is hard to find the studies on the systematically integrated methodology regarding the response time evaluation. In cases of APR1400 and OPR1000, the response time analysis for the plant protection system is partially included in the setpoint calculation and the response time test is separately performed via the specific plant procedure. The test technique has a drawback which is the difficulty to demonstrate completeness of timing test. The analysis technique has also a demerit of resulting in extreme times that not actually possible. Thus

  4. The structure of two subgenomic RNAs from human influenza virus A/PR/8/34.

    PubMed Central

    Winter, G; Fields, S; Ratti, G

    1981-01-01

    The nucleotide sequences of two subgenomic RNA segments from influenza virus A/PR/8/34 have been determined by cloning viral cDNA into the vector M13mp7. Sequence analysis was facilitated by a re-cloning strategy which takes advantage of both wild-type and amber derivatives of the M13 vector. The RNA species (444 and 480 nucleotides) contain the 5' and 3' termini of segment 1 and therefore derive by simple internal deletions of this segment. However, these species are not exact copies of the terminal regions of the progenitor segment but contain a few base changes. These differences suggest that after these RNAs have arisen, their sequences can drift, presumably reflecting a lower selective pressure than on the standard RNA segments. PMID:7335495

  5. Use case driven approach to develop simulation model for PCS of APR1400 simulator

    SciTech Connect

    Dong Wook, Kim; Hong Soo, Kim; Hyeon Tae, Kang; Byung Hwan, Bae

    2006-07-01

    The full-scope simulator is being developed to evaluate specific design feature and to support the iterative design and validation in the Man-Machine Interface System (MMIS) design of Advanced Power Reactor (APR) 1400. The simulator consists of process model, control logic model, and MMI for the APR1400 as well as the Power Control System (PCS). In this paper, a use case driven approach is proposed to develop a simulation model for PCS. In this approach, a system is considered from the point of view of its users. User's view of the system is based on interactions with the system and the resultant responses. In use case driven approach, we initially consider the system as a black box and look at its interactions with the users. From these interactions, use cases of the system are identified. Then the system is modeled using these use cases as functions. Lower levels expand the functionalities of each of these use cases. Hence, starting from the topmost level view of the system, we proceeded down to the lowest level (the internal view of the system). The model of the system thus developed is use case driven. This paper will introduce the functionality of the PCS simulation model, including a requirement analysis based on use case and the validation result of development of PCS model. The PCS simulation model using use case will be first used during the full-scope simulator development for nuclear power plant and will be supplied to Shin-Kori 3 and 4 plant. The use case based simulation model development can be useful for the design and implementation of simulation models. (authors)

  6. The Experience of Staging Nijinsky's "L'Apres-Midi d'un Faune" in a Higher Education Dance Program

    ERIC Educational Resources Information Center

    Curran, Tina

    2010-01-01

    This study documented the experiences of staging Vaslav Nijinsky's "L'Apres-midi d'un Faune" in a higher education dance program. The ballet was staged from Labanotation. Research questions focused on teaching and learning pedagogy, characterization of the process over time, experiences of the participants and teaching approaches. The project…

  7. 78 FR 47051 - Proposed Collection; Comment Request for Forms 943, 943-PR, 943-A, and 943A-PR

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-02

    ... Contribucion Federal Del Patrono De Empleados Agricolas, 943-A, Agricultural Employer's Record of Federal Tax Liability, and 943A-PR, Registro De La Obligacion Contributiva Del Patrono Agricola. DATES: Written comments... Para La Declarcion Anual De La Contribucion Federal Del Patrono De Empleados Agricolas (Form...

  8. 75 FR 44847 - Proposed Collection; Comment Request for Forms 943, 943-PR, 943-A, and 943A-PR

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-29

    ... Contribucion Federal Del Patrono De Empleados Agricolas, 943-A, Agricultural Employer's Record of Federal Tax Liability, and 943A-PR, Registro De La Obligacion Contributiva Del Patrono Agricola. DATES: Written comments... Agricolas (Form 943-PR), Agricultural Employer's Record of Federal Tax Liability (Form 943-A), and...

  9. Prenatal transportation alters the acute phase response (APR) of bull calves exposed to a lipopolysaccharide (LPS) challenge

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This study was designed to determine if prenatal transportation influences the acute phase response (APR) to a postnatal Lipopolysaccharide (LPS) challenge. Pregnant Brahman cows (n=96) matched by age and parity were separated into transported (TRANS; n=48; transported for 2 hours on gestational day...

  10. Mimicking acute and chronic stress exposure in naive beef steers alters the acute phase response (APR) associated with vaccination

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This study was designed to determine the effect of an acute versus chronic stress model on the APR associated with vaccination in naïve beef steers. Steers (n=32; 209 +/- 8 kg) were blocked by body weight and assigned to 1 of 3 treatments: 1) Chronic stress (CHR), 0.5 mg/kg body weight dexamethasone...

  11. The Relationship between AP[R] Exam Performance and College Outcomes. Research Report No. 2009-4

    ERIC Educational Resources Information Center

    Mattern, Krista D.; Shaw, Emily J.; Xiong, Xinhui

    2009-01-01

    This study focused on the relationship between students' Advanced Placement Program[R] (AP[R]) performance in AP English Language, Biology, Calculus, and U.S. History, and their subsequent college success. For each AP Exam studied, students were divided into three groups according to their AP Exam performance (no AP Exam taken, score of 1 or 2,…

  12. Isolation of ara-lac gene fusions in Salmonella typhimurium LT2 by using transducing bacteriophage Mu d (Apr lac).

    PubMed

    Lee, J H; Heffernan, L; Wilcox, G

    1980-09-01

    A specialized Mu transducing phage containing a gene encoding ampicillin resistance and the lac structural genes without the lac promotor [Mu d(apr lac)] has been constructed and used to create gene fusions in Escherichia coli (M. J. Cadadaban and S. N. Cohen, Proc. Natl. Acad. Sci. U.S.A. 76:4530--4533, 1979). Transposition of the Mu d(Apr lac) phage to chromosomal sites can result in lac expression being controlled by a chromosomal promoter. We have constructed an Escherichia coli K-12 strain in which the Mu d(Apr lac) phage is integrated into an F factor. The F+::Mu d(Apr lac) was then transferred by conjugation into a Salmonella typhimurium strain that was sensitive to L-arabinose. Strains containing gene fusions were selected as L-arabinose-resistant colonies after partial induction of the phage. Two classes of ara-lac fusion strains were isolated: (i) araC-lac fusions in which the expression of beta-galactosidase synthesis was constitutuve and not inducible by L-arabinose; and ((ii) fusion of the lac genes to the ara structural genes in which the expression of beta-galatosidase synthesis was induced 263-fold by L-arabinose.

  13. Commercial food irradiation

    SciTech Connect

    Black, E.F.; Libby, L.M.

    1983-06-01

    Food irradiation is discussed. Irradiation exposes food to gamma rays from a cobalt-60 or a cesium-137 source, or to high-energy electrons emitted by an electron accelerator. A major advantage is that food can be packaged either before or after treatment. FDA regulations with regard to irradiation are discussed. Comments on an 'Advance Notice' on irradiation, published by the FDA in 1981 are summarized.

  14. AFRRI reports, second quarter 1992. Rept. for Apr-Jul 92

    SciTech Connect

    Not Available

    1992-07-01

    This report includes the following topics: Short and long courses of ofloxacin therapy of Klebsiella pneumoniae sepsis following irradiation, Possible 'accelerated striatal aging' induced by 56Fe heavy-particle irradiation: Implications for manned space flights, Modulation of mortality by tissue trauma and sepsis in mice after radiation injury, Cytokine therapy in canine and primate models of radiation-induced marrow aplasia, Comparison of behavioral and radioprotective effects of WR-2721 and WR-3689, Energy transfer mechanisms in DNA: Relationship to energy deposition in sub-microscopic volumes, Role of interleukin 6 (IL-6) in protection from lethal irradiation and in endocrine responses to IL-1 and tumor necrosis factor, Effects on enhancing hemopoietic reconstitution and increasing survival following exposure to ionizing radiation, and Radioprotection of hematopoietic tissues in mice by lipoic acid.

  15. Acute exercise does not induce an acute phase response (APR) in Standardbred trotters.

    PubMed

    Kristensen, Lena; Buhl, Rikke; Nostell, Katarina; Bak, Lars; Petersen, Ellen; Lindholm, Maria; Jacobsen, Stine

    2014-04-01

    The purpose of the study was to investigate whether acute strenuous exercise (1600- to 2500-m race) would elicit an acute phase response (APR) in Standardbred trotters. Blood levels of several inflammatory markers [serum amyloid A (SAA), haptoglobin, fibrinogen, white blood cell count (WBC), and iron], muscle enzymes [creatinine kinase (CK) and aspartate transaminase (AST)], and hemoglobin were assessed in 58 Standardbred trotters before and after racing. Hemoglobin levels increased and iron levels decreased 12 to 14 h after racing and haptoglobin concentrations, white blood cell counts, and iron levels were decreased 2 and/or 7 d after racing. Concentrations of CK, AST, SAA, and fibrinogen were unaltered in response to racing. Acute strenuous exercise did not elicit an acute phase reaction. The observed acute increase in hemoglobin levels and decreases in haptoglobin and iron levels may have been caused by exercise-induced hemolysis, which indicates that horses might experience a condition similar to athlete's anemia in humans. The pathogenesis and clinical implications of the hematological and blood-biochemical changes elicited by acute exercise in Standardbred trotters in the present study warrant further investigation.

  16. Purification and characterization of a small size protease from Bacillus sp. APR-4.

    PubMed

    Kumar, D; Bhalla, T C

    2004-05-01

    A thermostable extracellular protease of Bacillus sp. APR-4 was purified by size-exclusion and ion-exchange chromatographic methods and its properties were studied. The purified enzyme had a specific activity of 21,000 U/mg of protein and gave single band on SDS/PAGE with a molecular mass of 16.9 KDa. This protease had an optimal pH of 9 and exhibited its highest activity at 60 degrees C. The enzyme activity was inhibited by EDTA, suggesting the presence of metal residue at the active site. Ca2+ (5 mM) had stabilising effect on the activity of protease, but Cu2+ (5 mM) had inhibitory effect. The enzyme exhibited highest specificity towards casein (1%) and had a Km of 26.3 mg/ml and a Vmax of 47.6 U/mg with casein as a substrate. The stability of this enzyme was evaluated in the presence of some organic solvents and the enzyme was stable in methanol, petroleum ether and ethanol. Detergents (Wheel, Farishta) had stimulatory effect on the activity of this enzyme.

  17. Welding irradiated stainless steel

    SciTech Connect

    Kanne, W.R. Jr.; Chandler, G.T.; Nelson, D.Z.; Franco-Ferreira, E.A.

    1993-12-31

    Conventional welding processes produced severe underbead cracking in irradiated stainless steel containing 1 to 33 appm helium from n,a reactions. A shallow penetration overlay technique was successfully demonstrated for welding irradiated stainless steel. The technique was applied to irradiated 304 stainless steel that contained 10 appm helium. Surface cracking, present in conventional welds made on the same steel at the same and lower helium concentrations, was eliminated. Underbead cracking was minimal compared to conventional welding methods. However, cracking in the irradiated material was greater than in tritium charged and aged material at the same helium concentrations. The overlay technique provides a potential method for repair or modification of irradiated reactor materials.

  18. Anti-Influenza Activity of Betulinic Acid from Zizyphus jujuba on Influenza A/PR/8 Virus

    PubMed Central

    Hong, Eun-Hye; Song, Jae Hyoung; Kang, Kyo Bin; Sung, Sang Hyun; Ko, Hyun-Jeong; Yang, Heejung

    2015-01-01

    Betulinic acid, a pentacyclic triterpene isolated from Jujube tree (Zizyphus jujuba Mill), has been known for a wide range of biological and medicinal properties such as antibacterial, antimalarial, anti-inflammatory, antihelmintic, antinociceptive, and anticancer activities. In the study, we investigated the antiviral activity on influenza A/PR/8 virus infected A549 human lung adenocarcinoma epithelial cell line and C57BL/6 mice. Betulinic acid showed the anti-influenza viral activity at a concentration of 50 μM without a significant cytotoxicity in influenza A/PR/8 virus infected A549 cells. Also, betulinic acid significantly attenuated pulmonary pathology including increased necrosis, numbers of inflammatory cells and pulmonary edema induced by influenza A/PR/8 virus infection compared with vehicle- or oseltamivir-treated mice in vivo model. The down-regulation of IFN-γ level, which is critical for innate and adaptive immunity in viral infection, after treating of betulinic acid in mouse lung. Based on the obtained results, it is suggested that betulinic acid can be the potential therapeutic agent for virus infection via anti-inflammatory activity. PMID:26157551

  19. Facteurs déterminants le regret après ligature tubaire

    PubMed Central

    Boufettal, Houssine; Mahdaoui, Sakher; Samouh, Naïma

    2014-01-01

    Introduction La ligature tubaire peut générer regret. Le but de cette étude est d’étudier le vécu après la stérilisation ainsi que le regret et ses facteurs de risque. Méthodes Il s'agit d'une étude rétrospective chez 52 femmes stérilisées entre 2004 et 2010. Résultats Vingt cinq (48%) femmes avaient regretté la réalisation de la ligature tubaire. La moyenne d’âge était de 40,5 ans. Le temps consacré aux explications était très court dans tous les cas. Trois quart des femmes n’était pas au courant des complications de la ligature tubaire. Le regret était dû au facteur religieux (23%), aux algies pelviennes (11,5%), au désir d'autres enfants (9,6%) ou à la prise de connaissance d'autres moyens contraceptifs (3,9%). Conclusion Un certains nombre de facteurs de risque de regret de la ligature tubaire sont retrouvés dans la littérature, comme dans notre série, dont l’âge, le désir de procréer, l'information incomplète, le délai de réflexion et le facteur religieux. PMID:25309644

  20. Predictors of exclusive breastfeeding: observations from the Alberta pregnancy outcomes and nutrition (APrON) study

    PubMed Central

    2013-01-01

    Background Despite growing evidence that supports the importance of 6-month exclusive breastfeeding, few Canadian mothers adhere to this, and early weaning onto solids is a common practice. This study assessed infant feeding transitions during the first 6 months postpartum and factors that predicted exclusive breastfeeding to 3 and 6 months. Methods This prospective cohort study was part of the Alberta Pregnancy Outcomes and Nutrition study (APrON). From an initial sample of 600 pregnant women recruited from Edmonton and Calgary, 402 mothers provided complete details at 3 months postpartum; 300 stayed on to provide information at 6 months postpartum. During pregnancy and at 3 and 6 months postpartum, data on maternal and infant socio-demographic, behavior, and feeding were collected. Results Even though there was a high rate of “ever having breastfed” (98.6%), exclusive breastfeeding rates for 3 and 6 months were 54.0% and 15.3%, respectively. After controlling for potential confounders, the study showed that mothers who held post-graduate university degrees were 3.76 times more likely to breastfeed exclusively for 6 months than those without a university degree (95% CI: 1.30-10.92; p = 0.015). In addition, mother of previous children were more likely to breastfeed exclusively for 6 months (OR: 2.21, 95% CI: 1.08-4.52; p = 0.031). Mothers who were in the highest quartile of the Iowa Infant Feeding Attitude Score were 4.29 and 5.40 times more likely to breastfeed exclusively for 3 months (95% CI: 1.31-14.08; p-trend < 0.001) and 6 months (95% CI: 2.75-10.60; P-trend < 0.001), respectively. Conclusions The 6-month exclusive breastfeeding rate in Alberta is considerably below national and international breastfeeding recommendations. Professional advice that focuses on prenatal maternal knowledge, attitudes, and misperceptions may promote adherence to World Health Organization breastfeeding guidelines. Knowing that exclusive breastfeeding

  1. Suivi après le traitement du cancer du sein

    PubMed Central

    Sisler, Jeffrey; Chaput, Geneviève; Sussman, Jonathan; Ozokwelu, Emmanuel

    2016-01-01

    Résumé Objectif Offrir aux médecins de famille un résumé des recommandations fondées sur les données probantes pour guider les soins aux survivantes traitées pour le cancer du sein. Qualité des données Une recherche documentaire a été effectuée dans MEDLINE entre 2000 et 2016 à l’aide des mots-clés anglais suivants : breast cancer, survivorship, follow-up care, aftercare, guidelines et survivorship care plans, en se concentrant sur la revue des lignes directrices publiées récemment par les organismes nationaux de cancérologie. Les données étaient de niveaux I à III. Message principal Les soins aux survivantes comportent 4 facettes : surveillance et dépistage, prise en charge des effets à long terme, promotion de la santé et coordination des soins. La surveillance des récidives ne se traduit que par une mammographie annuelle, et le dépistage d’autres cancers doit suivre les lignes directrices basées sur la population. La prise en charge des effets à long terme du cancer et de son traitement aborde des problèmes courants tels la douleur, la fatigue, le lymphœdème, la détresse et les effets indésirables des médicaments, de même que les préoccupations à long terme comme la santé du cœur et des os. La promotion de la santé met en relief les bienfaits de l’activité chez les survivantes du cancer, avec l’accent mis sur l’activité physique. Les soins aux survivantes sont de meilleure qualité lorsque divers services et professionnels de la santé participent aux soins, et le médecin de famille joue un rôle important dans la coordination des soins. Conclusion Les médecins de famille sont de plus en plus souvent les principaux fournisseurs de soins de suivi après le traitement du cancer du sein. Le cancer du sein doit être considéré comme une affection médicale chronique, même chez les femmes en rémission, et les patientes profitent de la même approche que celle utilisée pour les autres affections chroniques en

  2. Comminuting irradiated ferritic steel

    DOEpatents

    Bauer, Roger E.; Straalsund, Jerry L.; Chin, Bryan A.

    1985-01-01

    Disclosed is a method of comminuting irradiated ferritic steel by placing the steel in a solution of a compound selected from the group consisting of sulfamic acid, bisulfate, and mixtures thereof. The ferritic steel is used as cladding on nuclear fuel rods or other irradiated components.

  3. Perspective on food irradiation

    SciTech Connect

    Not Available

    1987-02-01

    Recent US Food and Drug Administration approval of irradiation treatment for fruit, vegetables and pork has stimulated considerable discussion in the popular press on the safety and efficacy of irradiation processing of food. This perspective is designed to summarize the current scientific information available on this issue.

  4. MASSIVE LEAKAGE IRRADIATOR

    DOEpatents

    Wigner, E.P.; Szilard, L.; Christy, R.F.; Friedman, F.L.

    1961-05-30

    An irradiator designed to utilize the neutrons that leak out of a reactor around its periphery is described. It avoids wasting neutron energy and reduces interference with the core flux to a minimum. This is done by surrounding all or most of the core with removable segments of the material to be irradiated within a matrix of reflecting material.

  5. Irradiation Creep in Graphite

    SciTech Connect

    Ubic, Rick; Butt, Darryl; Windes, William

    2014-03-13

    An understanding of the underlying mechanisms of irradiation creep in graphite material is required to correctly interpret experimental data, explain micromechanical modeling results, and predict whole-core behavior. This project will focus on experimental microscopic data to demonstrate the mechanism of irradiation creep. High-resolution transmission electron microscopy should be able to image both the dislocations in graphite and the irradiation-induced interstitial clusters that pin those dislocations. The team will first prepare and characterize nanoscale samples of virgin nuclear graphite in a transmission electron microscope. Additional samples will be irradiated to varying degrees at the Advanced Test Reactor (ATR) facility and similarly characterized. Researchers will record microstructures and crystal defects and suggest a mechanism for irradiation creep based on the results. In addition, the purchase of a tensile holder for a transmission electron microscope will allow, for the first time, in situ observation of creep behavior on the microstructure and crystallographic defects.

  6. Expression, purification, and characterization of the Necator americanus aspartic protease-1 (Na-APR-1 (M74)) antigen, a component of the bivalent human hookworm vaccine

    PubMed Central

    Seid, Christopher A; Curti, Elena; Jones, R Mark; Hudspeth, Elissa; Rezende, Wanderson; Pollet, Jeroen; Center, Lori; Versteeg, Leroy; Pritchard, Sonya; Musiychuk, Konstantin; Yusibov, Vidadi; Hotez, Peter J; Bottazzi, Maria Elena

    2015-01-01

    Over 400 million people living in the world's poorest developing nations are infected with hookworms, mostly of the genus Necator americanus. A bivalent human hookworm vaccine composed of the Necator americanus Glutathione S-Transferase-1 (Na-GST-1) and the Necator americanus Aspartic Protease-1 (Na-APR-1 (M74)) is currently under development by the Sabin Vaccine Institute Product Development Partnership (Sabin PDP). Both monovalent vaccines are currently in Phase 1 trials. Both Na-GST-1 and Na-APR-1 antigens are expressed as recombinant proteins. While Na-GST-1 was found to express with high yields in Pichia pastoris, the level of expression of Na-APR-1 in this host was too low to be suitable for a manufacturing process. When the tobacco plant Nicotiana benthamiana was evaluated as an expression system, acceptable levels of solubility, yield, and stability were attained. Observed expression levels of Na-APR-1 (M74) using this system are ∼300 mg/kg. Here we describe the achievements and obstacles encountered during process development as well as characterization and stability of the purified Na-APR-1 (M74) protein and formulated vaccine. The expression, purification and analysis of purified Na-APR-1 (M74) protein obtained from representative 5 kg reproducibility runs performed to qualify the Na-APR-1 (M74) production process is also presented. This process has been successfully transferred to a pilot plant and a 50 kg scale manufacturing campaign under current Good Manufacturing Practice (cGMP) has been performed. The 50 kg run has provided a sufficient amount of protein to support the ongoing hookworm vaccine development program of the Sabin PDP. PMID:25905574

  7. Processing of High Resolution, Multiparametric Radar Data for the Airborne Dual-Frequency Precipitation Radar APR-2

    NASA Technical Reports Server (NTRS)

    Tanelli, Simone; Meagher, Jonathan P.; Durden, Stephen L.; Im, Eastwood

    2004-01-01

    Following the successful Precipitation Radar (PR) of the Tropical Rainfall Measuring Mission, a new airborne, 14/35 GHz rain profiling radar, known as Airborne Precipitation Radar - 2 (APR-2), has been developed as a prototype for an advanced, dual-frequency spaceborne radar for a future spaceborne precipitation measurement mission. . This airborne instrument is capable of making simultaneous measurements of rainfall parameters, including co-pol and cross-pol rain reflectivities and vertical Doppler velocities, at 14 and 35 GHz. furthermore, it also features several advanced technologies for performance improvement, including real-time data processing, low-sidelobe dual-frequency pulse compression, and dual-frequency scanning antenna. Since August 2001, APR-2 has been deployed on the NASA P3 and DC8 aircrafts in four experiments including CAMEX-4 and the Wakasa Bay Experiment. Raw radar data are first processed to obtain reflectivity, LDR (linear depolarization ratio), and Doppler velocity measurements. The dataset is then processed iteratively to accurately estimate the true aircraft navigation parameters and to classify the surface return. These intermediate products are then used to refine reflectivity and LDR calibrations (by analyzing clear air ocean surface returns), and to correct Doppler measurements for the aircraft motion. Finally, the the melting layer of precipitation is detected and its boundaries and characteristics are identifIed at the APR-2 range resolution of 30m. The resulting 3D dataset will be used for validation of other airborne and spaceborne instruments, development of multiparametric rain/snow retrieval algorithms and melting layer characterization and statistics.

  8. Multi-analytical characterisation of D'Aprés Cormon by José Veloso Salgado

    NASA Astrophysics Data System (ADS)

    Cardeira, A. M.; Longelin, S.; Costa, S.; Candeias, A.; Carvalho, M. L.; Manso, M.

    2014-07-01

    This case study reveals the analytical characterisation carried out on 'D'Aprés Cormon' (1891) by Veloso Salgado, a copy of 'Caïn' (1880) by Fernando Cormon, belonging nowadays to Musée d'Orsay. Infrared Reflectography made in situ revealed underdrawing grid that was used to transpose the original painting to a smaller scale, pictorial style, execution method and retouched/restored areas. In situ EDXRF analysis together with Raman microscopy allowed the identification of gypsum, lead white, titanium white, yellow ochre, vermilion, ultramarine and lamp black. These results provide valuable information about the Salgado's palette and his production technique.

  9. Characterisation of the Thermostable Protease AprX in Strains of Pseudomonas Fluorescens and Impact on the Shelf-life of Dairy Products: Preliminary Results.

    PubMed

    Andreani, Nadia Andrea; Carraro, Lisa; Fasolato, Luca; Balzan, Stefania; Lucchini, Rosaria; Novelli, Enrico; Cardazzo, Barbara

    2016-09-20

    Bacterial proteases are involved in food spoilage and shelf-life reduction. Among the bacterial proteases, a predominant role in spoilage of dairy products seems to be played by the thermostable metallo-protease AprX, which is produced by various strains of Pseudomonas fluorescens. Differences in AprX enzyme activity among different strains were highlighted, but the most proteolytic strains were not identified. In this study, the presence of the aprX gene was evaluated in 69 strains isolated from food matrices and 18 reference strains belonging to the P. fluorescens group, which had been previously typed by the multi locus sequence typing method. Subsequently, a subset of reference strains was inoculated in ultra-high temperature milk, and the expression of the aprX gene was evaluated at 22 and 6°C. On the same milk samples, the proteolytic activity was then evaluated through Azocasein and trinitrobenzenesulfonic acid solution assays. Finally, to assess the applicability of the former assay directly on dairy products the proteolityc activity was tested on industrial ricotta samples using the Azocasein assay. These results demonstrate the spread of aprX gene in most strains tested and the applicability of Azocasein assay to monitor the proteolytic activity in dairy products.

  10. Characterisation of the Thermostable Protease AprX in Strains of Pseudomonas Fluorescens and Impact on the Shelf-life of Dairy Products: Preliminary Results

    PubMed Central

    Andreani, Nadia Andrea; Carraro, Lisa; Fasolato, Luca; Balzan, Stefania; Lucchini, Rosaria; Novelli, Enrico; Cardazzo, Barbara

    2016-01-01

    Bacterial proteases are involved in food spoilage and shelf-life reduction. Among the bacterial proteases, a predominant role in spoilage of dairy products seems to be played by the thermostable metallo-protease AprX, which is produced by various strains of Pseudomonas fluorescens. Differences in AprX enzyme activity among different strains were highlighted, but the most proteolytic strains were not identified. In this study, the presence of the aprX gene was evaluated in 69 strains isolated from food matrices and 18 reference strains belonging to the P. fluorescens group, which had been previously typed by the multi locus sequence typing method. Subsequently, a subset of reference strains was inoculated in ultra-high temperature milk, and the expression of the aprX gene was evaluated at 22 and 6°C. On the same milk samples, the proteolytic activity was then evaluated through Azocasein and trinitrobenzenesulfonic acid solution assays. Finally, to assess the applicability of the former assay directly on dairy products the proteolityc activity was tested on industrial ricotta samples using the Azocasein assay. These results demonstrate the spread of aprX gene in most strains tested and the applicability of Azocasein assay to monitor the proteolytic activity in dairy products. PMID:28217561

  11. Long-term trends of global solar ultraviolet-B, ultraviolet-A and total irradiances measured in Japan since 2001

    NASA Astrophysics Data System (ADS)

    Takeshita, Shu; Sasaki, Masako

    2017-02-01

    Global and diffuse solar ultraviolet-B, ultraviolet-A, and Total irradiances have been measured at Shonan Campus of Tokai University (Kanagawa, Japan, 35°21'N, 139°11'E) since 1990. Analysis of data recorded from Apr. 2001 to Dec. 2015 shows that daily integrated global UV-B irradiance has decreasing in the long-term as -0.381 %/year for the 95 % confidence interval in this period. More detail evaluation is made on the data recorded from Jan. 2009 to Dec. 2015. In this period, an increase trend in global UV-B irradiance was obtained (+0.607 %/year). This result suggests that critical factor on increase in UV-B irradiance is not only ozone amount but also amount of aerosols, sunshine duration and solar cycle.

  12. Alaskan Commodities Irradiation Project

    SciTech Connect

    Zarling, J.P.; Swanson, R.B.; Logan, R.R.; Das, D.K.; Lewis, C.E.; Workman, W.G.; Tumeo, M.A.; Hok, C.I.; Birklid, C.A.; Bennett, F.L.

    1988-12-01

    The ninety-ninth US Congress commissioned a six-state food irradiation research and development program to evaluate the commercial potential of this technology. Hawaii, Washington, Iowa, Oklahoma and Florida as well as Alaska have participated in the national program; various food products including fishery products, red meats, tropical and citrus fruits and vegetables have been studied. The purpose of the Alaskan study was to review and evaluate those factors related to the technical and economic feasibility of an irradiator in Alaska. This options analysis study will serve as a basis for determining the state's further involvement in the development of food irradiation technology. 40 refs., 50 figs., 53 tabs.

  13. Food irradiation in perspective

    NASA Astrophysics Data System (ADS)

    Henon, Y. M.

    1995-02-01

    Food irradiation already has a long history of hopes and disappointments. Nowhere in the world it plays the role that it should have, including in the much needed prevention of foodborne diseases. Irradiated food sold well wherever consumers were given a chance to buy them. Differences between national regulations do not allow the international trade of irradiated foods. While in many countries food irradiation is still illegal, in most others it is regulated as a food additive and based on the knowledge of the sixties. Until 1980, wholesomeness was the big issue. Then the "prerequisite" became detection methods. Large amounts of money have been spent to design and validate tests which, in fact, aim at enforcing unjustified restrictions on the use of the process. In spite of all the difficulties, it is believed that the efforts of various UN organizations and a growing legitimate demand for food safety should in the end lead to recognition and acceptance.

  14. [The irradiation process].

    PubMed

    Barillot, I; Chauvet, B; Hannoun Lévi, J M; Lisbona, A; Leroy, T; Mahé, M A

    2016-09-01

    The purpose of this article is to describe the regulatory framework of the radiotherapy practice in France, the external irradiation and brachytherapy process and the guidelines for patient follow-up.

  15. Total lymphoid irradiation

    SciTech Connect

    Sutherland, D.E.; Ferguson, R.M.; Simmons, R.L.; Kim, T.H.; Slavin, S.; Najarian, J.S.

    1983-05-01

    Total lymphoid irradiation by itself can produce sufficient immunosuppression to prolong the survival of a variety of organ allografts in experimental animals. The degree of prolongation is dose-dependent and is limited by the toxicity that occurs with higher doses. Total lymphoid irradiation is more effective before transplantation than after, but when used after transplantation can be combined with pharmacologic immunosuppression to achieve a positive effect. In some animal models, total lymphoid irradiation induces an environment in which fully allogeneic bone marrow will engraft and induce permanent chimerism in the recipients who are then tolerant to organ allografts from the donor strain. If total lymphoid irradiation is ever to have clinical applicability on a large scale, it would seem that it would have to be under circumstances in which tolerance can be induced. However, in some animal models graft-versus-host disease occurs following bone marrow transplantation, and methods to obviate its occurrence probably will be needed if this approach is to be applied clinically. In recent years, patient and graft survival rates in renal allograft recipients treated with conventional immunosuppression have improved considerably, and thus the impetus to utilize total lymphoid irradiation for its immunosuppressive effect alone is less compelling. The future of total lymphoid irradiation probably lies in devising protocols in which maintenance immunosuppression can be eliminated, or nearly eliminated, altogether. Such protocols are effective in rodents. Whether they can be applied to clinical transplantation remains to be seen.

  16. Blood irradiation: Rationale and technique

    SciTech Connect

    Lewis, M.C. )

    1990-01-01

    Upon request by the local American Red Cross, the Savannah Regional Center for Cancer Care irradiates whole blood or blood components to prevent post-transfusion graft-versus-host reaction in patients who have severely depressed immune systems. The rationale for blood irradiation, the total absorbed dose, the type of patients who require irradiated blood, and the regulations that apply to irradiated blood are presented. A method of irradiating blood using a linear accelerator is described.

  17. Sulphur flux through the sulphate assimilation pathway is differently controlled by adenosine 5'-phosphosulphate reductase under stress and in transgenic poplar plants overexpressing gamma-ECS, SO, or APR.

    PubMed

    Scheerer, Ursula; Haensch, Robert; Mendel, Ralf R; Kopriva, Stanislav; Rennenberg, Heinz; Herschbach, Cornelia

    2010-01-01

    Sulphate assimilation provides reduced sulphur for the synthesis of cysteine, methionine, and numerous other essential metabolites and secondary compounds. The key step in the pathway is the reduction of activated sulphate, adenosine 5'-phosphosulphate (APS), to sulphite catalysed by APS reductase (APR). In the present study, [(35)S]sulphur flux from external sulphate into glutathione (GSH) and proteins was analysed to check whether APR controls the flux through the sulphate assimilation pathway in poplar roots under some stress conditions and in transgenic poplars. (i) O-Acetylserine (OAS) induced APR activity and the sulphur flux into GSH. (ii) The herbicide Acetochlor induced APR activity and results in a decline of GSH. Thereby the sulphur flux into GSH or protein remained unaffected. (iii) Cd treatment increased APR activity without any changes in sulphur flux but lowered sulphate uptake. Several transgenic poplar plants that were manipulated in sulphur metabolism were also analysed. (i) Transgenic poplar plants that overexpressed the gamma-glutamylcysteine synthetase (gamma-ECS) gene, the enzyme catalysing the key step in GSH formation, showed an increase in sulphur flux into GSH and sulphate uptake when gamma-ECS was targeted to the cytosol, while no changes in sulphur flux were observed when gamma-ECS was targeted to plastids. (ii) No effect on sulphur flux was observed when the sulphite oxidase (SO) gene from Arabidopsis thaliana, which catalyses the back reaction of APR, that is the reaction from sulphite to sulphate, was overexpressed. (iii) When Lemna minor APR was overexpressed in poplar, APR activity increased as expected, but no changes in sulphur flux were observed. For all of these experiments the flux control coefficient for APR was calculated. APR as a controlling step in sulphate assimilation seems obvious under OAS treatment, in gamma-ECS and SO overexpressing poplars. A possible loss of control under certain conditions, that is Cd treatment

  18. Investigation of laser-induced retinal damage. Annual report, 1 Apr 91-31 Mar 92

    SciTech Connect

    Glickman, R.D.; Lam, K.W.

    1992-04-22

    Laser-induced, photooxidative damage in ocular tissue was studied with a quantitative assay using high performance liquid chromatography (HPLC) to separate oxidized and reduced ascorbic acid in exposed tissue components. We demonstrated that ascorbic acid, incubated with whole, bovine retinal pigment epithelial (RPE) cells, was oxidized when the reaction mixture was exposed to the output of an argon-ion continuous wave laser The amount of ascorbic acid oxidized was proportional to the irradiance of the sample, and the reaction was wavelength-dependent, with short-wavelength visible light more effective than long-wavelengths in driving the, reaction. The photosensitizing activity was associated with the RPE melanin pigment granules, and was not lost after disrupting or heating the RPE cells. Because melanin was known to form free radicals when illuminated, we hypothesized that ascorbic acid detoxified the light-activated melanin free radicals while being itself oxidized in process. If the supply of reduced ascorbic acid were exhausted, however, the activated melanin could have been the source of tissue-damaging radicals. This model was consistent with a photochemical damage mechanism involving light-activated melanin.

  19. Research, development, and demonstration of algal production raceway (APR) systems for the production of hydrocarbon resources

    SciTech Connect

    Laws, E.A.

    1984-02-01

    A fractional factorial experimental design was used to determine the maximum production and photosynthetic efficiency that could be achieved in shallow algal mass culture systems (SAMCS) of the marine diatom Phaeodactylum tricornutum. Dilution rate and CO/sub 2/ supply were found to be the most important system parameters. Maximum production was found to be about 25 g dry wt m/sup -2/d/sup -1/. This production corresponded to a photosynthetic efficiency of 5.6%. These figures are 50 to 100% better than the production rates achieved in earlier P. tricornutum cultures using conventional culture techniques. The results are consistent with a theoretical model of the impact of the flashing light effect on algal mass culture production. This model predicts that at the typical irradiances in Hawaii, full utilization of the flashing light effect should enhance production by 70% to over 200%. It was concluded that the use of foil arrays in the experimental flume creates systematic vertical mixing on a time scale suitable for utilizing the flashing light effect. Production of P. tricornutum culture is probably limited by temperature. P. tricornutum cannot survive at temperatures in excess of 25/sup 0/C in outdoor mass cultures. Growth of mesophilic species in the temperature range 30 to 35/sup 0/C may well result in even higher production than that achieved with P. tricornutum.

  20. ORNL irradiation creep facility

    SciTech Connect

    Reiley, T.C.; Auble, R.L.; Beckers, R.M.; Bloom, E.E.; Duncan, M.G.; Saltmarsh, M.J.; Shannon, R.H.

    1980-09-01

    A machine was developed at ORNL to measure the rates of elongation observed under irradiation in stressed materials. The source of radiation is a beam of 60 MeV alpha particles from the Oak Ridge Isochronous Cyclotron (ORIC). This choice allows experiments to be performed which simulate the effects of fast neutrons. A brief review of irradiation creep and experimental constraints associated with each measurement technique is given. Factors are presented which lead to the experimental choices made for the Irradiation Creep Facility (ICF). The ICF consists of a helium-filled chamber which houses a high-precision mechanical testing device. The specimen to be tested must be thermally stabilized with respect to the temperature fluctuations imposed by the particle beam which passes through the specimen. Electrical resistance of the specimen is the temperature control parameter chosen. Very high precision in length measurement and temperature control are required to detect the small elongation rates relevant to irradiation creep in the test periods available (approx. 1 day). The apparatus components and features required for the above are presented in some detail, along with the experimental procedures. The damage processes associated with light ions are discussed and displacement rates are calculated. Recent irradiation creep results are given, demonstrating the suitability of the apparatus for high resolution experiments. Also discussed is the suitability of the ICF for making high precision thermal creep measurements.

  1. Carcinoïde primitif du rein métastasant après 12 ans

    PubMed Central

    Bacha, Dhouha; Lahmar, Ahlem; Gharbi, Lassad; Slama, Sana Ben; Bouraoui, Saadia; Chatti, Samia; Regaya, Sabeh Mzabi

    2016-01-01

    Les carcinoïdes primitifs du rein sont rares avec une centaine de cas rapportés dans la littérature. Sur le plan histologique, il s'agit d'une tumeur bien différenciée dont la morphologie rejoint souvent celle des carcinoïdes dans les autres localisations. Nous rapportons un cas de carcinoïde primitif du rein survenant chez un homme de 41 ans, découvert à la suite de métastases hépatiques. La tumeur était particulière par son architecture tubulo-papillaire, suggérant à tort le diagnostic de carcinome papillaire du rein. Ce diagnostic a été redressé 12 ans après, à la suite de l'apparition d'autres métastases hépatiques, osseuses et pulmonaires. PMID:27217899

  2. 78 FR 14155 - Special Conditions: Learjet Inc., Model LJ-200-1A10 Airplane; Use of Automatic Power Reserve (APR...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-05

    ... Power Reserve (APR), an Automatic Takeoff Thrust Control System (ATTCS), for Go-Around Performance... airplane will have novel or unusual design features associated with utilizing go-around performance credit...: Federal eRegulations Portal: Go to http://www.regulations.gov/ and follow the online instructions...

  3. Synthesis of Key Points from the OSEP Early Childhood Transition FAQ (SPP/APR Indicators C-8, B-11 and B-12)

    ERIC Educational Resources Information Center

    Diefendorf, M.; Henson, J.; Lucas, A.; Whaley, K.

    2010-01-01

    This document is a synthesis of the key points provided in the Office of Special Education Programs (OSEP) Early Childhood Transition FAQs: SPP/APR indicators C-8 and B-12 released on December 1, 2009. It was developed to assist states with the implementation of effective transition policies and practices. The following is included: (1) Transition…

  4. FOOD IRRADIATION REACTOR

    DOEpatents

    Leyse, C.F.; Putnam, G.E.

    1961-05-01

    An irradiation apparatus is described. It comprises a pressure vessel, a neutronic reactor active portion having a substantially greater height than diameter in the pressure vessel, an annular tank surrounding and spaced from the pressure vessel containing an aqueous indium/sup 1//sup 1//sup 5/ sulfate solution of approximately 600 grams per liter concentration, means for circulating separate coolants through the active portion and the space between the annular tank and the pressure vessel, radiator means adapted to receive the materials to be irradiated, and means for flowing the indium/sup 1//sup 1//sup 5/ sulfate solution through the radiator means.

  5. Fuel or irradiation subassembly

    DOEpatents

    Seim, O.S.; Hutter, E.

    1975-12-23

    A subassembly for use in a nuclear reactor is described which incorporates a loose bundle of fuel or irradiation pins enclosed within an inner tube which in turn is enclosed within an outer coolant tube and includes a locking comb consisting of a head extending through one side of the inner sleeve and a plurality of teeth which extend through the other side of the inner sleeve while engaging annular undercut portions in the bottom portion of the fuel or irradiation pins to prevent movement of the pins.

  6. Irradiating insect pests

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This is a non-technical article focusing on phytosanitary uses of irradiation. In a series of interview questions, I present information on the scope of the invasive species problem and the contribution of international trade in agricultural products to the movement of invasive insects. This is foll...

  7. Update on meat irradiation

    SciTech Connect

    Olson, D.G.

    1997-12-01

    The irradiation of meat and poultry in the United States is intended to eliminate pathogenic bacteria from raw product, preferably after packaging to prevent recontamination. Irradiation will also increase the shelf life of raw meat and poultry products approximately two to three times the normal shelf life. Current clearances in the United States are for poultry (fresh or frozen) at doses from 1.5 to 3.0 kGy and for fresh pork at doses from 0.3 to 1.0 kGy. A petition for the clearance of all red meat was submitted to the Food and Drug Administration (FDA) in July 1994. The petition is for clearances of fresh meat at doses from 1.5 to 4.5 kGy and for frozen meat at {approximately}2.5 to 7.5 kGy. Clearance for red meat is expected before the end of 1997. There are 28 countries that have food irradiation clearances, of which 18 countries have clearances for meat or poultry. However, there are no uniform categories or approved doses for meat and poultry among the countries that could hamper international trade of irradiated meat and poultry.

  8. Phytosanitary applications of irradiation

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Phytosanitary treatments are used to disinfest agricultural commodities of quarantine pests so the commodities can be shipped across quarantine barriers to trade. Ionizing irradiation is a promising treatment that is increasing in use. Almost 19,000 tons of sweet potatoes and several fruits, plus ...

  9. Generic phytosanitary irradiation treatments

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The history of the development of generic phytosanitary irradiation (PI) treatments is discussed beginning with its initial proposal in 1986. Generic PI treatments in use today are 150 Gy for all hosts of Tephritidae, 250 Gy for all arthropods on mango and papaya shipped from Australia to New Zeala...

  10. NSUF Irradiated Materials Library

    SciTech Connect

    Cole, James Irvin

    2015-09-01

    The Nuclear Science User Facilities has been in the process of establishing an innovative Irradiated Materials Library concept for maximizing the value of previous and on-going materials and nuclear fuels irradiation test campaigns, including utilization of real-world components retrieved from current and decommissioned reactors. When the ATR national scientific user facility was established in 2007 one of the goals of the program was to establish a library of irradiated samples for users to access and conduct research through competitively reviewed proposal process. As part of the initial effort, staff at the user facility identified legacy materials from previous programs that are still being stored in laboratories and hot-cell facilities at the INL. In addition other materials of interest were identified that are being stored outside the INL that the current owners have volunteered to enter into the library. Finally, over the course of the last several years, the ATR NSUF has irradiated more than 3500 specimens as part of NSUF competitively awarded research projects. The Logistics of managing this large inventory of highly radioactive poses unique challenges. This document will describe materials in the library, outline the policy for accessing these materials and put forth a strategy for making new additions to the library as well as establishing guidelines for minimum pedigree needed to be included in the library to limit the amount of material stored indefinitely without identified value.

  11. Electron spin resonance detection of oxygen radicals released by UVA-irradiated human fibroblasts

    NASA Astrophysics Data System (ADS)

    Souchard, J. P.; Pierlot, G.; Barbacanne, M. A.; Charveron, M.; Bonafé, J.-L.; Nepveu, F.

    1999-01-01

    This work reports the electron spin resonance (ESR) detection of oxygenated radicals (OR) released by cultured human fibroblasts after UVA (365 nm) exposure. 5,5-dimethyl-pyrroline-N-oxide (DMPO) was used as spin trap. After a UVA irradiation of one hour, followed by a latent period of at least 45 min., and an incubation time of 30 min. in a trapping medium containing DMPO, glucose, Na^+, K+ and Ca2+ an ESR signal was recorded. By contrast, an ESR signal was produced after only 15 min. incubation when calcium ionophore A23187 was used. Although the ESR signal was characteristic of the hydroxyl adduct DMPO-OH, the use of catalase and superoxide dismutase (SOD) revealed that UVA stimulated fibroblasts released the superoxide anion O2- in the medium. SOD, vitamin C and (+)-catechin inhibited the release of superoxide generated by human fibroblasts stimulated with A23187 calcium ionophore at 5 units/ml, 10-5 M and 2× 10-4 M, respectively. Dans ce travail nous présentons la détection par résonance de spin électronique (RSE) de radicaux oxygénés (RO) libérés par des fibroblastes humains en culture après irradiation aux UVA (365 nm). Le 5,5-diméthyl-1-pyrroline-N-oxyde (DMPO) a été utilisé comme piégeur de spin. Après une irradiation aux UVA d'une heure, suivie d'une période de latence d'au moins 45 min. et d'une incubation de 30 min. dans un milieu de piégeage composé de DMPO, glucose, Na^+, K+ et Ca2+, un signal RPE est enregistré. L'ionophore calcique A23187 entraîne l'apparition d'un signal RPE après seulement 15 min. d'incubation. Bien que le signal RPE obtenu corresponde à l'adduit DMPO-OH du radical hydroxyle, l'utilisation de catalase et de superoxyde dismutase (SOD) a révélé que les fibroblastes libéraient l'anion superoxyde dans le milieu de culture. Sur ce modèle cellulaire la SOD, la vitamine C et la (+) catéchine inhibent la production du radical superoxyde aux concentrations respectivement de 5 unités/ml, 10-5 M et 2× 10-4M.

  12. Le don après un décès d'origine cardiocirculatoire au Canada

    PubMed Central

    Shemie, Sam D.; Baker, Andrew J.; Knoll, Greg; Wall, William; Rocker, Graeme; Howes, Daniel; Davidson, Janet; Pagliarello, Joe; Chambers-Evans, Jane; Cockfield, Sandra; Farrell, Catherine; Glannon, Walter; Gourlay, William; Grant, David; Langevin, Stéphan; Wheelock, Brian; Young, Kimberly; Dossetor, John

    2006-01-01

    Résumé Ces recommandations sont le fruit d'un processus multidisciplinaire national ayant duré un an et visant à déterminer si et comment l'on pourrait procéder au don d'organes après un décès d'origine cardiocirculatoire («don après le décès cardiocirculatoire», ou DDC) au Canada. Le forum national organisé en février 2005 a permis aux participants de discuter et d'élaborer des recommandations sur les principes, interventions et pratiques se rapportant au DDC. Les aspects éthiques et juridiques ont été abordés dans les discussions. À la fin du Forum, la majorité des participants ont été favorables à l'implantation de programmes de DDC au Canada. Les participants du Forum ont également convenu qu'il fallait formuler et prôner des valeurs fondamentales pour orienter l'élaboration de programmes et de protocoles basés sur le cadre médical, éthique et juridique établi lors de cette réunion. Même si la possibilité d'un don d'organes et de tissus doit faire partie intégrante des soins de fin de vie, il faut insister sur le fait que le devoir de diligence envers les patients mourants et leurs familles doit demeurer la priorité des équipes soignantes. La complexité et les répercussions profondes du décès sont reconnues et doivent être respectées, de même que les différences personnelles, ethnoculturelles et religieuses face à la mort et au don d'organes. Les décisions d'arrêter le traitement de maintien des fonctions vitales, la prise en charge des derniers moments de la vie et le diagnostic de décès selon des critères cardiocirculatoires doivent être distincts et indépendants des processus de don et transplantation. Ce rapport contient des recommandations destinées aux gestionnaires de program, aux autorités sanitaires régionales et aux instances appelés à élaborer les protocoles de DDC. Les programmes doivent être conçus en fonction des éléments suivants : direction et planification locales, éducation et

  13. Food irradiation: Activities and potentialities

    NASA Astrophysics Data System (ADS)

    Doellstaedt, R.; Huebner, G.

    After the acceptance of food irradiation up to an overall average dose of 10 kGy recommended by the Joint FAO/IAEA/WHO Expert Committee on the Wholesomeness of Irradiated Food in October 1980, the G.D.R. started a programme for the development of techniques for food irradiation. A special onion irradiator was designed and built as a pilot plant for studying technological and economic parameters of the irradiation of onions. The new principle of bulk-cargo irradiation allows the integration of this technology into the usual harvest technology for onions on the way from field to storage. Scientific and applied research work has been carried out in the past 3 yr on the irradiation of spices, potatoes, eviscerated chicken, animal feeds, fodder yeast, drugs and vaccines. In connection with the irradiation of eviscerated chicken, fodder yeast and animal feeds the basis of an antisalmonella programme has been discussed. Germ-count-reduced spices were employed for the production of test charges of preserves and tinned products. The results have led to the decision to design and build a new multipurpose irradiator for food irradiation. In order to cover the legal aspects of food irradiation the Ministry of Health issued regulations concerning the recommendation of irradiated food in the G.D.R.

  14. ELECTRON IRRADIATION OF SOLIDS

    DOEpatents

    Damask, A.C.

    1959-11-01

    A method is presented for altering physical properties of certain solids, such as enhancing the usefulness of solids, in which atomic interchange occurs through a vacancy mechanism, electron irradiation, and temperature control. In a centain class of metals, alloys, and semiconductors, diffusion or displacement of atoms occurs through a vacancy mechanism, i.e., an atom can only move when there exists a vacant atomic or lattice site in an adjacent position. In the process of the invention highenergy electron irradiation produces additional vacancies in a solid over those normally occurring at a given temperature and allows diffusion of the component atoms of the solid to proceed at temperatures at which it would not occur under thermal means alone in any reasonable length of time. The invention offers a precise way to increase the number of vacancies and thereby, to a controlled degree, change the physical properties of some materials, such as resistivity or hardness.

  15. BIOLOGICAL IRRADIATION FACILITY

    DOEpatents

    McCorkle, W.H.; Cern, H.S.

    1962-04-24

    A facility for irradiating biological specimens with neutrons is described. It includes a reactor wherein the core is off center in a reflector. A high-exposure room is located outside the reactor on the side nearest the core while a low-exposure room is located on the opposite side. Means for converting thermal neutrons to fast neutrons are movably disposed between the reactor core and the high and low-exposure rooms. (AEC)

  16. Surface segregation during irradiation

    SciTech Connect

    Rehn, L.E.; Lam, N.Q.

    1985-10-01

    Gibbsian adsorption is known to alter the surface composition of many alloys. During irradiation, four additional processes that affect the near-surface alloy composition become operative: preferential sputtering, displacement mixing, radiation-enhanced diffusion and radiation-induced segregation. Because of the mutual competition of these five processes, near-surface compositional changes in an irradiation environment can be extremely complex. Although ion-beam induced surface compositional changes were noted as long as fifty years ago, it is only during the past several years that individual mechanisms have been clearly identified. In this paper, a simple physical description of each of the processes is given, and selected examples of recent important progress are discussed. With the notable exception of preferential sputtering, it is shown that a reasonable qualitative understanding of the relative contributions from the individual processes under various irradiation conditions has been attained. However, considerably more effort will be required before a quantitative, predictive capability can be achieved. 29 refs., 8 figs.

  17. APR-246/PRIMA-1(MET) rescues epidermal differentiation in skin keratinocytes derived from EEC syndrome patients with p63 mutations.

    PubMed

    Shen, Jinfeng; van den Bogaard, Ellen H; Kouwenhoven, Evelyn N; Bykov, Vladimir J N; Rinne, Tuula; Zhang, Qiang; Tjabringa, Geuranne S; Gilissen, Christian; van Heeringen, Simon J; Schalkwijk, Joost; van Bokhoven, Hans; Wiman, Klas G; Zhou, Huiqing

    2013-02-05

    p53 and p63 share extensive sequence and structure homology. p53 is frequently mutated in cancer, whereas mutations in p63 cause developmental disorders manifested in ectodermal dysplasia, limb defects, and orofacial clefting. We have established primary adult skin keratinocytes from ectrodactyly, ectodermal dysplasia, and cleft lip/palate (EEC) syndrome patients with p63 mutations as an in vitro human model to study the disease mechanism in the skin of EEC patients. We show that these patient keratinocytes cultured either in submerged 2D cultures or in 3D skin equivalents have impaired epidermal differentiation and stratification. Treatment of these patient keratinocytes with the mutant p53-targeting compound APR-246/PRIMA-1(MET) (p53 reactivation and induction of massive apoptosis) that has been successfully tested in a phase I/II clinical trial in cancer patients partially but consistently rescued morphological features and gene expression during epidermal stratification in both 2D and 3D models. This rescue coincides with restoration of p63 target-gene expression. Our data show that EEC patient keratinocytes with p63 mutations can be used for characterization of the abnormal molecular circuitry in patient skin and may open possibilities for the design of novel pharmacological treatment strategies for patients with mutant p63-associated developmental abnormalities.

  18. FDA perspective on food irradiation

    SciTech Connect

    Pauli, G.H.

    1994-12-31

    The Center for Food Safety and Applied Nutrition (CFSAN) monitors the safety of food irradiation. A few limited uses are regulated, and occasionally CFSAN receives a petition for a new use. Despite extensive studies (more than 400) showing the safety of food irradiation, a cloud of suspicion continues to hang over this issue in the mind of the public. People perceive food irradiation and direct body irradiation as having similar implications. Food irradiation is banned in two states in the United States. Food is irradiated for the following purposes: delay of ripening, prevention of sprouting, eradication of pests and sterilization, and allowing commodities to be stored unrefrigerated for long periods of time. The dosage depends on the purpose of the irradiation. Radiolytic products are formed during irradiation and during storage afterward. Most of these products are also formed during conventional preservation. In 1980, CFSAN, then the Bureau of Foods, introduced the term unique radiolytic products for compounds not identified in foods after conventional processing. Although the existence of URPs was never proven chemically, the term has caused anxiety. Irradiation of foods in the commercially useful range does not generate radioactivity above natural background. Because radiolytic products formed from beef, chicken, and pork are primarily the same, irradiated foods of similar food groups may be evaluated generically.

  19. Replacement of 137Cs irradiators with x-ray irradiators.

    PubMed

    Dodd, Brian; Vetter, Richard J

    2009-02-01

    Self-shielded 137Cs irradiators have been used for many years to irradiate blood products to prevent graft vs. host disease and to irradiate cells and small animals in research. A report by the National Academy of Sciences recommends that careful consideration be given to replacement of 137Cs irradiators with x-ray irradiators. Several manufacturers and users of x-ray irradiators were contacted to determine costs of replacing and maintaining 137Cs irradiators with x-ray units and to assess users' experience with x-ray irradiators. Purchase costs of x-ray units are similar to 137Cs irradiators, but maintenance costs are significantly higher if annual service contracts are used. Performance of the two irradiator types appears to be equivalent, but in some cases x-ray irradiations may need to be performed in multiple configurations to achieve adequate uniformity in dose. No literature reports were found that evaluated the biological effectiveness of x rays vs. 137Cs gamma rays; therefore, a careful study should be conducted to determine the biological effectiveness of x rays vs. 137Cs gamma rays for biological responses relevant to transfusion medicine and immunological research. Throughput may be problematic for large transfusion medicine programs, and back-up plans may be necessary in case the x-ray unit needs to be taken out of service for extended maintenance. Disposition of a 137Cs irradiator will add to the cost of replacement with an x-ray unit, but disposal may be possible through the U.S. Department of Energy's Off-Site Source Recovery Program.

  20. Antiviral activity of the plant extracts from Thuja orientalis, Aster spathulifolius, and Pinus thunbergii against influenza virus A/PR/8/34.

    PubMed

    Won, Ji-Na; Lee, Seo-Yong; Song, Dae-sub; Poo, Haryoung

    2013-01-01

    Influenza viruses cause significant morbidity and mortality in humans through epidemics or pandemics. Currently, two classes of anti-influenza virus drugs, M2 ion-channel inhibitors (amantadin and rimantadine) and neuraminidase inhibitors (oseltamivir and zanamivir), have been used for the treatment of the influenza virus infection. Since the resistance to these drugs has been reported, the development of a new antiviral agent is necessary. In this study, we examined the antiviral efficacy of the plant extracts against the influenza A/PR/8/34 infection. In vitro, the antiviral activities of the plant extracts were investigated using the cell-based screening. Three plant extracts, Thuja orientalis, Aster spathulifolius, and Pinus thunbergii, were shown to induce a high cell viability rate after the infection with the influenza A/PR/8/34 virus. The antiviral activity of the plant extracts also increased as a function of the concentration of the extracts and these extracts significantly reduced the visible cytopathic effect caused by virus infections. Furthermore, the treatment with T. orientalis was shown to have a stronger inhibitory effect than that with A. spathulifolius or P. thunbergii. These results may suggest that T. orientalis has anti-influenza A/PR/8/34 activity.

  1. Craniospinal irradiation techniques

    SciTech Connect

    Scarlatescu, Ioana Avram, Calin N.; Virag, Vasile

    2015-12-07

    In this paper we present one treatment plan for irradiation cases which involve a complex technique with multiple beams, using the 3D conformational technique. As the main purpose of radiotherapy is to administrate a precise dose into the tumor volume and protect as much as possible all the healthy tissues around it, for a case diagnosed with a primitive neuro ectoderm tumor, we have developed a new treatment plan, by controlling one of the two adjacent fields used at spinal field, in a way that avoids the fields superposition. Therefore, the risk of overdose is reduced by eliminating the field divergence.

  2. Irradiation of northwest agricultural products

    NASA Astrophysics Data System (ADS)

    Eakin, D. E.; Tingey, G. I.

    1985-02-01

    Irradiation of food for disinfestation and preservation is increasing in importance because of increasing restrictions on various chemical treatments. Irradiation treatment is of particular interest in the Northwest because of a growing supply of agricultural products and the need to develop new export markets. Several products have, or could potentially have, significant export markets if stringent insect ocntrol procedures are developed and followed. Due to the recognized potential benefits of irradiation, this program was conducted to evaluate the benefits of using irradiation on Northwest agricultural products. Commodities currently included in the program are cherries, apples, asparagus, spices, hay, and hides.

  3. Food irradiation and the consumer

    NASA Astrophysics Data System (ADS)

    A Thomas, P.

    The poster presents a review of research work undertaken on the perception and understanding that consumers have of food irradiation. Food irradiation is not a revolutionary new food processing technique, in fact it is probably one of the most investigated methods presently available. Many countries such as Belgium, France, Denmark, Italy, Spain, the Netherlands and the United States of America permit food irradiation. In Britain it is presently banned although this is currently under review. Awareness of food irradiation by the general public in Britain, although not extensively researched would appear to be increasing, especially in the light of recent media coverage. New quantitative and qualitative work indicates that the general public are concerned about the safety and effectiveness of food irradiation. Research has shown that a large proportion of consumers in Britain, if given the opportunity to purchase irradiated food, would not do so. Further exploration into this response revealed the fact that consumers are confused over what food irradiation is. In addition, there is concern over the detection of irradiated food. The views presented in this paper, of the consumer reaction to irradiated food are of great importance to those involved in the food industry and industries allied to it, which are ultimately dependent on the consumer for their commercial survival.

  4. PRIMA-1Met/APR-246 displays high antitumor activity in multiple myeloma by induction of p73 and Noxa.

    PubMed

    Saha, Manujendra N; Jiang, Hua; Yang, Yijun; Reece, Donna; Chang, Hong

    2013-11-01

    Targeting p53 by the small-molecule PRIMA-1(Met)/APR-246 has shown promising preclinical activity in various cancer types. However, the mechanism of PRIMA-1(Met)-induced apoptosis is not completely understood and its effect on multiple myeloma cells is unknown. In this study, we evaluated antitumor effect of PRIMA-1(Met) alone or its combination with current antimyeloma agents in multiple myeloma cell lines, patient samples, and a mouse xenograft model. Results of our study showed that PRIMA-1(Met) decreased the viability of multiple myeloma cells irrespective of p53 status, with limited cytotoxicity toward normal hematopoietic cells. Treatment of multiple myeloma cells with PRIMA-1(Met) resulted in induction of apoptosis, inhibition of colony formation, and migration. PRIMA-1(Met) restored wild-type conformation of mutant p53 and induced activation of p73 upregulating Noxa and downregulating Mcl-1 without significant modulation of p53 level. siRNA-mediated silencing of p53 showed a little effect on apoptotic response of PRIMA-1(Met), whereas knockdown of p73 led to substantial attenuation of apoptotic activity in multiple myeloma cells, indicating that PRIMA-1(Met)-induced apoptosis is, at least in part, p73-dependent. Importantly, PRIMA-1(Met) delayed tumor growth and prolonged survival of mice bearing multiple myeloma tumor. Furthermore, combined treatment of PRIMA-1(Met) with dexamethasone or doxorubicin displayed synergistic effects in both multiple myeloma cell lines and primary multiple myeloma samples. Consistent with our in vitro observations, cotreatment with PRIMA-1(Met) and dexamethasone resulted in enhanced antitumor activity in vivo. Our study for the first time shows antimyeloma activity of PRIMA-1(Met) and provides the rationale for its clinical evaluation in patients with multiple myeloma, including the high-risk group with p53 mutation/deletion.

  5. Activity of Melaleuca alternifolia (tea tree) oil on Influenza virus A/PR/8: study on the mechanism of action.

    PubMed

    Garozzo, A; Timpanaro, R; Stivala, A; Bisignano, G; Castro, A

    2011-01-01

    Our previous study demonstrated that Melaleuca alternifolia (tea tree) oil (TTO) had an interesting antiviral activity against Influenza A in MDCK cells. In fact, when we tested TTO and some of its components, we found that TTO had an inhibitory effect on influenza virus replication at doses below the cytotoxic dose; terpinen-4-ol, terpinolene, and alfa-terpineol were the main active components. The aim of this study was to investigate the mechanism of action of TTO and its active components against Influenza A/PR/8 virus subtype H1N1 in MDCK cells. None of the test compounds showed virucidal activity nor any protective action for the MDCK cells. Thus, the effect of TTO and its active components on different steps of the replicative cycle of influenza virus was studied by adding the test compounds at various times after infection. These experiments revealed that viral replication was significantly inhibited if TTO was added within 2h of infection, indicating an interference with an early step of the viral replicative cycle of influenza virus. The influence of the compound on the virus adsorption step, studied by the infective center assay, indicated that TTO did not interfere with cellular attachment of the virus. TTO did not inhibit influenza virus neuraminidase activity, as shown by the experiment measuring the amount of 4-methylumbelliferone, cleaved by the influenza virus neuraminidase from the fluorogenic substrate 2'-O-(4-methylumbelliferyl)-N-acetylneuraminic acid. The effect of TTO on acidification of cellular lysosomes was studied by vital staining with acridine orange using bafilomycin A1 as positive control. The treatment of cells with 0.01% (v/v) of TTO at 37°C for 4h before staining inhibited the acridine orange accumulation in acid cytoplasmic vesicles, indicating that TTO could inhibit viral uncoating by an interference with acidification of intralysosomal compartment.

  6. Food irradiation and sterilization

    NASA Astrophysics Data System (ADS)

    Josephson, Edward S.

    Radiation sterilization of food (radappertization) requires exposing food in sealed containers to ionizing radiation at absorbed doses high enough (25-70 kGy) to kill all organisms of food spoilage and public health significance. Radappertization is analogous to thermal canning is achieving shelf stability (long term storage without refrigeration). Except for dry products in which autolysis is negligible, the radappertization process also requires that the food be heated to an internal temperature of 70-80°C (bacon to 53°C) to inactivate autolytic enzymes which catalyze spoilage during storage without refrigeration. To minimize the occurence of irradiation induced off-flavors and odors, undesirable color changes, and textural and nutritional losses from exposure to the high doses required for radappertization, the foods are vacuum sealed and irradiated frozen (-40°C to -20°C). Radappertozed foods have the characteristic of fresh foods prepared for eating. Radappertization can substitute in whole or in part for some chemical food additives such as ethylene oxide and nitrites which are either toxic, carcinogenic, mutagenic, or teratogenic. After 27 years of testing for "wholesomeness" (safety for consumption) of radappertized foods, no confirmed evidence has been obtained of any adverse effecys of radappertization on the "wholesomeness" characteristics of these foods.

  7. Wholesomeness of irradiated food

    NASA Astrophysics Data System (ADS)

    Ehlermann, Dieter A. E.

    2016-12-01

    Just with the emergence of the idea to treat food by ionizing radiation, the concerns were voiced whether it would be safe to consume such food. Now, we look back on more than hundred years of research into the 'wholesomeness', a terminology developed during those efforts. This review will cover the many questions which had been raised, explaining the most relevant ones in some detail; it will also give place to the concerns and elucidate their scientific relevance and background. There has never been any other method of food processing studied in such depth and in such detail as food irradiation. The conclusion based on science is: Consumption of any food treated at any high dose is safe, as long as the food remains palatable. This conclusion has been adopted by WHO, also by international and national bodies. Finally, this finding has also been adopted by Codex Alimentarius in 2003, the international standard for food. However, this conclusion has not been adopted and included at its full extent in most national regulations. As the literature about wholesomeness of irradiated food is abundant, this review will use only a few, most relevant references, which will guide the reader to further reading.

  8. Qualification sous irradiation du crayon cea: de la conception des composants a l'irradiation d'assemblages en reacteur de puissance

    NASA Astrophysics Data System (ADS)

    Marin, Jean-François; Pillet, Claude; François, Bernard; Morize, Pierre; Petitgrand, Sylvie; Atabek, Rose-Marie; Houdaille, Brigitte

    1982-04-01

    Cet article résume les principaux résultats obtenus au CEA au cours des dix dernières années dans la conception, la qualification et la fabrication des différents éléments originaux constitutifs d'un assemblage de réacteur à eau pressurisée, notamment: l'oxyde UO 2 obtenu par le procédé du Double Cycle Inverse, la gaine en zircaloy 4 recris talllsée, la grille à ressort papillon, la structure à grilles coulissantes. Les etudes et essais hors-pile de comportement thermomécanique du crayon et thermohydraulique des composants de l'assemblage, les irradiations paramétriques de crayons jusqu'à une combustion massique élevée, la validation à partir d'examens aprés irradiation des principaux modèles introduits dans les calculs de conception, enfin l'introduction en réacteur prototype, puis en réacteur de puissance d'assemblages comportant ces différents éléments, constituent les principales étapes de ce développement.

  9. Commercial implementation of food irradiation

    NASA Astrophysics Data System (ADS)

    Welt, M. A.

    In July 1981, the first specifically designed multi-purpose irradiation facility for food irradiation was put into service by the Radiation Technology, Inc. subsidiary Process Technology, Inc. in West Memphis, Arkansas. The operational experience gained, resulted in an enhanced design which was put into commercial service in Haw River, North Carolina, by another subsidiary, Process Technology (N.C.), Inc. in October 1983. These facilities have enabled the food industry to assess the commercial viability of food irradiation. Further impetus towards commercialization of food irradiation was gained in March 1981 with the filing in the Federal Register, by the FDA, of an Advanced Proposed Notice of Rulemaking for Food Irradiation. Two years later in July 1983, the FDA approved the first food additive regulation involving food irradiation in nineteen years, when they approved the Radiation Technology, Inc. petition calling for the sanitization of spices, onion powder and garlic powder at a maximum dosage of 10 kGy. Since obtaining the spice irradiation approval, the FDA has accepted four additional petitions for filing in the Federal Register. One of the petitions which extended spice irradiation to include insect disinfestation has issued into a regulation while the remaining petitions covering the sanitization of herbs, spice blends, vegetable seasonings and dry powdery enzymes as well as the petition to irradiate hog carcasses and pork products for trichinae control at 1 kGy, are expected to issue either before the end of 1984 or early in 1985. More recently, food irradiation advocates in the United States received another vote of confidence by the announcement that a joint venture food irradiation facility to be constructed in Hawaii by Radiation Technology, is backed by a contractual committment for the processing of 40 million pounds of produce per year. Another step was taken when the Port of Salem, New Jersey announced that the Radiation Technology Model RT-4104

  10. Pallet irradiators for food processing

    NASA Astrophysics Data System (ADS)

    McKinnon, R. G.; Chu, R. D. H.

    This paper looks at the various design concepts for the irradiation processing of food products, with particular emphasis on handling the products on pallets. Pallets appear to offer the most attractive method for handling foods from many considerations. Products are transported on pallets. Warehouse space is commonly designed for pallet storage and, if products are already palletized before and after irradiation, then labour could be saved by irradiating on pallets. This is also an advantage for equipment operation since a larger carrier volume means lower operation speeds. Different pallet irradiator design concepts are examined and their suitability for several applications are discussed. For example, low product holdup for fast turn around will be a consideration for those operating an irradiation "service" business; others may require a very large source where efficiency is the primary requirement and this will not be consistent with low holdup. The radiation performance characteristics and processing costs of these machines are discussed.

  11. Phytosanitary irradiation - Development and application

    NASA Astrophysics Data System (ADS)

    Hallman, Guy J.; Loaharanu, Paisan

    2016-12-01

    Phytosanitary irradiation, the use of ionizing radiation to disinfest traded agricultural commodities of regulated pests, is a growing use of food irradiation that has great continued potential for increase in commercial application. In 2015 approximately 25,000 t of fresh fruits and vegetables were irradiated globally for phytosanitary purposes. Phytosanitary irradiation has resulted in a paradigm shift in phytosanitation in that the final burden of proof of efficacy of the treatment has shifted from no live pests upon inspection at a port of entry (as for all previous phytosanitary treatments) to total dependence on certification that the treatment for target pests is based on adequate science and is commercially conducted and protected from post-treatment infestation. In this regard phytosanitary irradiation is managed more like a hazard analysis and critical control point (HACCP) approach more consistent with food safety than phytosanitation. Thus, phytosanitary irradiation offers a more complete and rigorous methodology for safeguarding than other phytosanitary measures. The role of different organizations in achieving commercial application of phytosanitary irradiation is discussed as well as future issues and applications, including new generic doses.

  12. New facility for post irradiation examination of neutron irradiated beryllium

    SciTech Connect

    Ishitsuka, Etsuo; Kawamura, Hiroshi

    1995-09-01

    Beryllium is expected as a neutron multiplier and plasma facing materials in the fusion reactor, and the neutron irradiation data on properties of beryllium up to 800{degrees}C need for the engineering design. The acquisition of data on the tritium behavior, swelling, thermal and mechanical properties are first priority in ITER design. Facility for the post irradiation examination of neutron irradiated beryllium was constructed in the hot laboratory of Japan Materials Testing Reactor to get the engineering design data mentioned above. This facility consist of the four glove boxes, dry air supplier, tritium monitoring and removal system, storage box of neutron irradiated samples. Beryllium handling are restricted by the amount of tritium;7.4 GBq/day and {sup 60}Co;7.4 MBq/day.

  13. Proton irradiation of simple gas mixtures: Influence of irradiation parameters

    NASA Technical Reports Server (NTRS)

    Sack, Norbert J.; Schuster, R.; Hofmann, A.

    1990-01-01

    In order to get information about the influence of irradiation parameters on radiolysis processes of astrophysical interest, methane gas targets were irradiated with 6.5 MeV protons at a pressure of 1 bar and room temperature. Yields of higher hydrocarbons like ethane or propane were found by analysis of irradiated gas samples using gas chromatography. The handling of the proton beam was of great experimental importance for determining the irradiation parameters. In a series of experiments current density of the proton beam and total absorbed energy were shown to have a large influence on the yields of produced hydrocarbons. Mechanistic interpretations of the results are given and conclusions are drawn with regard to the chemistry and the simulation of various astrophysical systems.

  14. (Irradiation creep of graphite)

    SciTech Connect

    Kennedy, C.R.

    1990-12-21

    The traveler attended the Conference, International Symposium on Carbon, to present an invited paper, Irradiation Creep of Graphite,'' and chair one of the technical sessions. There were many papers of particular interest to ORNL and HTGR technology presented by the Japanese since they do not have a particular technology embargo and are quite open in describing their work and results. In particular, a paper describing the failure of Minor's law to predict the fatigue life of graphite was presented. Although the conference had an international flavor, it was dominated by the Japanese. This was primarily a result of geography; however, the work presented by the Japanese illustrated an internal program that is very comprehensive. This conference, a result of this program, was better than all other carbon conferences attended by the traveler. This conference emphasizes the need for US participation in international conferences in order to stay abreast of the rapidly expanding HTGR and graphite technology throughout the world. The United States is no longer a leader in some emerging technologies. The traveler was surprised by the Japanese position in their HTGR development. Their reactor is licensed and the major problem in their graphite program is how to eliminate it with the least perturbation now that most of the work has been done.

  15. Generic phytosanitary irradiation treatments

    NASA Astrophysics Data System (ADS)

    Hallman, Guy J.

    2012-07-01

    The history of the development of generic phytosanitary irradiation (PI) treatments is discussed beginning with its initial proposal in 1986. Generic PI treatments in use today are 150 Gy for all hosts of Tephritidae, 250 Gy for all arthropods on mango and papaya shipped from Australia to New Zealand, 300 Gy for all arthropods on mango shipped from Australia to Malaysia, 350 Gy for all arthropods on lychee shipped from Australia to New Zealand and 400 Gy for all hosts of insects other than pupae and adult Lepidoptera shipped to the United States. Efforts to develop additional generic PI treatments and reduce the dose for the 400 Gy treatment are ongoing with a broad based 5-year, 12-nation cooperative research project coordinated by the joint Food and Agricultural Organization/International Atomic Energy Agency Program on Nuclear Techniques in Food and Agriculture. Key groups identified for further development of generic PI treatments are Lepidoptera (eggs and larvae), mealybugs and scale insects. A dose of 250 Gy may suffice for these three groups plus others, such as thrips, weevils and whiteflies.

  16. Irradiation of Northwest agricultural products

    SciTech Connect

    Eakin, D.E.; Tingey, G.L.

    1985-02-01

    Irradiation of food for disinfestation and preservation is increasing in importance because of increasing restrictions on various chemical treatments. Irradiation treatment is of particular interest in the Northwest because of a growing supply of agricultural products and the need to develop new export markets. Several products have, or could potentially have, significant export markets if stringent insect control procedures are developed and followed. Due to the recognized potential benefits of irradiation, Pacific Northwest Laboratory (PNL) is conducting this program to evaluate the benefits of using irradiation on Northwest agricultural products under the US Department of Energy (DOE) Defense Byproducts Production and Utilization Program. Commodities currently included in the program are cherries, apples, asparagus, spices, hay, and hides.

  17. Irradiation pretreatment for coal desulfurization

    NASA Technical Reports Server (NTRS)

    Hsu, G. C.

    1979-01-01

    Process using highly-penetrating nuclear radiation (Beta and Gamma radiation) from nuclear power plant radioactive waste to irradiate coal prior to conventional desulfurization procedures increases total extraction of sulfur.

  18. Slag recycling of irradiated vanadium

    SciTech Connect

    Gorman, Patrick K.

    1995-04-05

    An experimental inductoslag apparatus to recycle irradiated vanadium was fabricated and tested. An experimental electroslag apparatus was also used to test possible slags. The testing was carried out with slag materials that were fabricated along with impurity bearing vanadium samples. Results obtained include computer simulated thermochemical calculations and experimentally determined removal efficiencies of the transmutation impurities. Analyses of the samples before and after testing were carried out to determine if the slag did indeed remove the transmutation impurities from the irradiated vanadium.

  19. Consumer attitudes toward irradiated food

    SciTech Connect

    Conley, S.

    1994-12-31

    Throughout history, new methods of food preservation have been met with skepticism and fear. Such processes as pasteurization and canning were denounced as being dangerous, detrimental to nutrients, or an excuse for dirty products. Now comes irradiation, and activists argue against this new process for the same reasons. Publicly, the perception is that consumers, distrustful of nuclear power, will never buy or accept irradiated food.

  20. Calculating Irradiance For Photosynthesis In The Ocean

    NASA Technical Reports Server (NTRS)

    Collins, Donald J.; Davis, Curtiss O.; Booth, C. Rockwell; Kiefer, Dale A.; Stallings, Casson

    1990-01-01

    Mathematical model predicts available and usable irradiances. Yields estimates of irradiance available for photosynthesis (Epar) and irradiance usable for photosynthesis (Epur) as functions of depth in ocean. Describes Epur and Epar in terms of spectral parameters measured remotely (from satellites or airplanes). These irradiances useful in studies of photosynthetic productivity of phytoplankton in euphotic layer.

  1. Irradiance-dependent UVB Photocarcinogenesis

    PubMed Central

    Lan, Cheng-Che E.; Wu, Ching-Shuang; Huang, Shu-Mei; Wu, Chin-Han; Lai, Hsiao-Chi; Peng, Yu-Ting; Hou, Pao-Sheng; Yang, Hui-Jun; Chen, Gwo-Shing

    2016-01-01

    Ultraviolet B (UVB) radiation from the sun may lead to photocarcinogenesis of the skin. Sunscreens were used to protect the skin by reducing UVB irradiance, but sunscreen use did not reduce sunburn episodes. It was shown that UVB-induced erythema depends on surface exposure but not irradiance of UVB. We previously showed that irradiance plays a critical role in UVB-induced cell differentiation. This study investigated the impact of irradiance on UVB-induced photocarcinogenesis. For hairless mice receiving equivalent exposure of UVB radiation, the low irradiance (LI) UVB treated mice showed more rapid tumor development, larger tumor burden, and more keratinocytes harboring mutant p53 in the epidermis as compared to their high irradiance (HI) UVB treated counterpart. Mechanistically, using cell models, we demonstrated that LI UVB radiation allowed more keratinocytes harboring DNA damages to enter cell cycle via ERK-related signaling as compared to its HI UVB counterpart. These results indicated that at equivalent exposure, UVB radiation at LI has higher photocarcinogenic potential as compared to its HI counterpart. Since erythema is the observed sunburn at moderate doses and use of sunscreen was not found to associate with reduced sunburn episodes, the biological significance of sunburn with or without sunscreen use warrants further investigation. PMID:27869214

  2. Computing Solar EUV Irradiance Variability

    NASA Astrophysics Data System (ADS)

    Warren, H. P.

    2014-12-01

    The solar EUV irradiance plays a central role in determining the state of the Earth's upper atmosphere. The EUV irradiance at the shortest wavelengths, which is highly variable over time scales from seconds to decades, is particularly important for many aspects of space weather. Systematic spectrally resolved observations at the shortest EUV wavelengths, however, have been rare and there is a need to develop a methodology for estimating and forecasting the solar irradiance at all EUV wavelengths from sparse data sets. In this presentation we report on our efforts to use AIA DEM calculations to estimate the solar EUV irradiance at wavelength below 450 Å, where the emission is predominately optically thin. To validate our AIA DEM calculations we have performed extensive comparisons with simultaneous observations from the EVE instrument on SDO and the EIS instrument on Hinode and find that with the proper constraints we can generally reproduce the results obtained with detailed spectroscopic observations. Using a proxy for solar activity derived from photospheric magnetic field measurements we extend our model calculations to previous solar cycles and discuss how the model can be used to forecast EUV irradiance variability over short time scales. Finally, we speculate on what is needed to further develop semi-empirical and physical models for use in understanding the solar spectral irradiance at these wavelengths.

  3. Targeted cytoplasmic irradiation and autophagy.

    PubMed

    Wu, Jinhua; Zhang, Bo; Wuu, Yen-Ruh; Davidson, Mercy M; Hei, Tom K

    2017-03-01

    The effect of ionizing irradiation on cytoplasmic organelles is often underestimated because the general dogma considers direct DNA damage in the nuclei to be the primary cause of radiation induced toxicity. Using a precision microbeam irradiator, we examined the changes in mitochondrial dynamics and functions triggered by targeted cytoplasmic irradiation with α-particles. Mitochondrial dysfunction induced by targeted cytoplasmic irradiation led to activation of autophagy, which degraded dysfunctional mitochondria in order to maintain cellular energy homeostasis. The activation of autophagy was cytoplasmic irradiation-specific and was not detected in nuclear irradiated cells. This autophagic process was oxyradical-dependent and required the activity of the mitochondrial fission protein dynamin related protein 1 (DRP1). The resultant mitochondrial fission induced phosphorylation of AMP activated protein kinase (AMPK) which leads to further activation of the extracellular signal-related kinase (ERK) 1/2 with concomitant inhibition of the mammalian target of rapamycin (mTOR) to initiate autophagy. Inhibition of autophagy resulted in delayed DNA damage repair and decreased cell viability, which supports the cytoprotective function of autophagy. Our results reveal a novel mechanism in which dysfunctional mitochondria are degraded by autophagy in an attempt to protect cells from toxic effects of targeted cytoplasmic radiation.

  4. Peut-on réaliser une analgésie péridurale après un blood patch récent?

    PubMed Central

    Chkoura, Khalid; Kechna, Hicham; Loutid, Jaouad; Ouzad, Omar; Hachimi, Moulay Ahmed; Hannafi, Sidi Mohamed

    2015-01-01

    Le blood patch constitue le traitement de référence du syndrome post ponction lombaire. Son efficacité a été démontrée par plusieurs essais randomisés comparant le BPE aux mesures conservatrices et au placebo. Il consiste en l'injection d'une quantité de sang autologue dans l'espace péridurale afin d'obturer la brèche dure-mérienne. La réalisation d'une analgésie péridurale après antécédent de blood patch est possible, malgré la persistance de questions sur les délais de retour à la normal de l'espace péridurale. Nous rapportons un cas où une analgésie péridurale a été réalisée avec succès trois semaines après un blood patch. PMID:26600909

  5. Application of the response surface methodology for optimizing the activity of an aprE-driven gene expression system in Bacillus subtilis.

    PubMed

    El-Helow, E R; Abdel-Fattah, Y R; Ghanem, K M; Mohamad, E A

    2000-10-01

    The major targets for improvement of recombinant expression systems in microbial cells are gene dosage, transcriptional control machinery and, to some extent, translation. Here we show that optimization of fermentation conditions by applying statistically designed, multifactorial experiments offers an additional method for potential enhancement of gene expression systems. A chromosomally encoded fusion between the Bacillus subtilis aprE regulatory region and the E. coli lacZ gene carried by the B. subtilis host cells was used. The 2 x SG sporulation medium was used as a basal medium. Among the 11 fermentation factors we examined, the most significant variables influencing beta-galactosidase expression were statistically elucidated for optimization and included peptone, MgSO4.7H2O, and KCl. The optimum concentrations of these variables were predicted by using a second-order polynomial model fitted to the results obtained by applying the Box-Behnken design, a response surface method. Calculated optimum concentrations were predicted to confer a maximum yield of 2,423.5 beta-galactosidase specific activity units. A verification experiment performed under optimal conditions yielded 96% of the predicted specific activity value with an increase by a factor of almost 5 compared with the results obtained under basal conditions.

  6. Irradiation hardening of pure tungsten exposed to neutron irradiation

    DOE PAGES

    Hu, Xunxiang; Koyanagi, Takaaki; Fukuda, Makoto; ...

    2016-08-26

    In this paper, pure tungsten samples have been neutron irradiated in HFIR at 90–850 °C to 0.03–2.2 dpa. A dispersed barrier hardening model informed by the available microstructure data has been used to predict the hardness. Comparison of the model predictions and the measured Vickers hardness reveals the dominant hardening contribution at various irradiation conditions. For tungsten samples irradiated in HFIR, the results indicate that voids and dislocation loops contributed to the hardness increase in the low dose region (<0.3 dpa), while the formation of intermetallic second phase precipitation, resulting from transmutation, dominates the radiation-induced strengthening beginning with a relativelymore » modest dose (>0.6 dpa). Finally, the precipitate contribution is most pronounced for the HFIR irradiations, whereas the radiation-induced defect cluster microstructure can rationalize the entirety of the hardness increase observed in tungsten irradiated in the fast neutron spectrum of Joyo and the mixed neutron spectrum of JMTR.« less

  7. Irradiation hardening of pure tungsten exposed to neutron irradiation

    SciTech Connect

    Hu, Xunxiang; Koyanagi, Takaaki; Fukuda, Makoto; Kumar, N. A. P. Kiran; Snead, Lance L.; Wirth, Brian D.; Katoh, Yutai

    2016-08-26

    In this paper, pure tungsten samples have been neutron irradiated in HFIR at 90–850 °C to 0.03–2.2 dpa. A dispersed barrier hardening model informed by the available microstructure data has been used to predict the hardness. Comparison of the model predictions and the measured Vickers hardness reveals the dominant hardening contribution at various irradiation conditions. For tungsten samples irradiated in HFIR, the results indicate that voids and dislocation loops contributed to the hardness increase in the low dose region (<0.3 dpa), while the formation of intermetallic second phase precipitation, resulting from transmutation, dominates the radiation-induced strengthening beginning with a relatively modest dose (>0.6 dpa). Finally, the precipitate contribution is most pronounced for the HFIR irradiations, whereas the radiation-induced defect cluster microstructure can rationalize the entirety of the hardness increase observed in tungsten irradiated in the fast neutron spectrum of Joyo and the mixed neutron spectrum of JMTR.

  8. Irradiation damage to the lung

    SciTech Connect

    Fennessy, J.J.

    1987-07-01

    While some degree of injury to normal, non-tumor-bearing, intrathoracic structures always occurs following irradiation for cure or palliation of neoplastic disease, clinical expression of this injury is uncommon. However, under certain circumstances, clinical manifestations may be severe and life threatening. Acute radiographic manifestations of pulmonary injury usually appear either synchronous with or, more typically, seven to ten days after the onset of the clinical syndrome. The acute signs of edema and slight volume loss within the irradiated zone are nonspecific except for their temporal and spatial relationship to the irradiation of the patient. Resolution of the acute changes is followed by pulmonary cicatrization, which is almost always stable within one year after completion of therapy. Change in postirradiation scarring following stabilization of the reaction must always be assumed to be due to some other process. While the radiograph primarily reveals pulmonary injury, all tissues, including the heart and major vessels, are susceptible, and the radiologist must recognize that any change within the thorax of a patient who has undergone thoracic irradiation may be a complication of that treatment. Differentiation of irradiation injury from residual or recurrent tumor, drug reaction, or opportunistic infection may be difficult and at times impossible.

  9. Food irradiation: Public opinion surveys

    SciTech Connect

    Kerr, S.D.

    1987-01-01

    The Canadian government are discussing the legislation, regulations and practical protocol necessary for the commercialization of food irradiation. Food industry marketing, public relations and media expertise will be needed to successfully introduce this new processing choice to retailers and consumers. Consumer research to date including consumer opinion studies and market trials conducted in the Netherlands, United States, South Africa and Canada will be explored for signposts to successful approaches to the introduction of irradiated foods to retailers and consumers. Research has indicated that the terms used to describe irradiation and information designed to reduce consumer fears will be important marketing tools. Marketers will be challenged to promote old foods, which look the same to consumers, in a new light. Simple like or dislike or intention to buy surveys will not be effective tools. Consumer fears must be identified and effectively handled to support a receptive climate for irradiated food products. A cooperative government, industry, health professional, consumer association and retailer effort will be necessary for the successful introduction of irradiated foods into the marketplace. Grocery Products Manufacturers of Canada is a national trade association of more than 150 major companies engaged in the manufacture of food, non-alcoholic beverages and array of other national-brand consumer items sold through retail outlets.

  10. Real-Time PCR Quantification and Diversity Analysis of the Functional Genes aprA and dsrA of Sulfate-Reducing Prokaryotes in Marine Sediments of the Peru Continental Margin and the Black Sea.

    PubMed

    Blazejak, Anna; Schippers, Axel

    2011-01-01

    Sulfate-reducing prokaryotes (SRP) are ubiquitous and quantitatively important members in many ecosystems, especially in marine sediments. However their abundance and diversity in subsurface marine sediments is poorly understood. In this study, the abundance and diversity of the functional genes for the enzymes adenosine 5'-phosphosulfate reductase (aprA) and dissimilatory sulfite reductase (dsrA) of SRP in marine sediments of the Peru continental margin and the Black Sea were analyzed, including samples from the deep biosphere (ODP site 1227). For aprA quantification a Q-PCR assay was designed and evaluated. Depth profiles of the aprA and dsrA copy numbers were almost equal for all sites. Gene copy numbers decreased concomitantly with depth from around 10(8)/g sediment close to the sediment surface to less than 10(5)/g sediment at 5 mbsf. The 16S rRNA gene copy numbers of total bacteria were much higher than those of the functional genes at all sediment depths and used to calculate the proportion of SRP to the total Bacteria. The aprA and dsrA copy numbers comprised in average 0.5-1% of the 16S rRNA gene copy numbers of total bacteria in the sediments up to a depth of ca. 40 mbsf. In the zone without detectable sulfate in the pore water from about 40-121 mbsf (Peru margin ODP site 1227), only dsrA (but not aprA) was detected with copy numbers of less than 10(4)/g sediment, comprising ca. 14% of the 16S rRNA gene copy numbers of total bacteria. In this zone, sulfate might be provided for SRP by anaerobic sulfide oxidation. Clone libraries of aprA showed that all isolated sequences originate from SRP showing a close relationship to aprA of characterized species or form a new cluster with only distant relation to aprA of isolated SRP. For dsrA a high diversity was detected, even up to 121 m sediment depth in the deep biosphere.

  11. Monoclinically distorted perovskites, A{sub 2}ZnTiO{sub 6} (A=Pr, Gd): Rietveld refinement, and dielectric studies

    SciTech Connect

    Das, Nibedita; Nath, Masood A.; Thakur, Gohil S.; Thirumal, M.; Ganguli, Ashok K.

    2015-09-15

    Double perovskite related oxide A{sub 2}ZnTiO{sub 6}A=Pr, Gd were synthesized by the solid state reaction method at 1523 K. The structure and microstructure of the compounds were studied by X-ray, SAED and FESEM. Rietveld refinement of the powder X-ray analysis shows that the compounds crystallizes in monoclinic space group P2{sub 1}/n (a{sup +}b{sup −}b{sup −}) with unit cell parameter √2a{sub p}×√2a{sub p}×2a{sub p} (a=5.5026(1) Å, b=5.6305(1) Å, c=7.8149(1) Å, β=90.02(1)° for Pr{sub 2}ZnTiO{sub 6} and a=5.3621(1) Å, b=5.6565(2) Å, c=7.6779(2) Å and β=90.264(2)° for Gd{sub 2}ZnTiO{sub 6}. Electron diffraction study confirms P2{sub 1}/n symmetry of the oxides. The monoclinic distortion is larger in Gd{sub 2}ZnTiO{sub 6} than Pr{sub 2}ZnTiO{sub 6} which is associated with the tolerance factor and the tilting angle of ZnO{sub 6} and TiO{sub 6} octahedra (ϕ=13.64° for Pr{sub 2}ZnTiO{sub 6} and 16.51° for Gd{sub 2}ZnTiO{sub 6}). The compounds are highly ordered. The charge and size difference between B site cations are the driving force for the ordering of the B′O{sub 6} and B″O{sub 6} octahedra. Pr{sub 2}ZnTiO{sub 6} shows a dielectric constant of 27 and dielectric loss of 0.003 while Gd{sub 2}ZnTiO{sub 6} has a dielectric constant of 17 and dielectric loss of 0.005 measured at 1 MHz. - Graphical abstract: Synthesis of new double perovskite dielectric material with very low dielectric loss. - Highlights: • Synthesis of new monoclinically distorted double perovskite (Pr{sub 2}ZnTiO{sub 6}). • Synthesis of monoclinically distorted double perovskite (Gd{sub 2}ZnTiO{sub 6}). • Selected area electron diffraction study of A{sub 2}ZnTiO{sub 6} (A=Pr, Gd). • Study of dielectric properties of A{sub 2}ZnTiO{sub 6} (A=Pr, Gd)

  12. Cinétique de la troponine Ic et valeurs seuils pour le diagnostic d'infarctus du myocarde après chirurgie cardiaque sous circulation extracorporelle

    PubMed Central

    Kallel, Samy; Jarraya, Anwar; Ellouze, Maged; Frikha, Imed; Karoui, Abbdelhamid

    2012-01-01

    Introduction L'objectif de ce travail était d’étudier la cinétique de la Troponine Ic (TnIc) après chirurgie cardiaque sous circulation extracorporelle (CEC) et établir des valeurs seuils de TnIc pour le diagnostic d'infarctus du myocarde (IDM) post opératoire. Il s'agissait d'une étude prospective type cohorte observationnelle. Méthodes Nous avons inclus 37 patients âgés de plus de 18 ans proposés pour chirurgie valvulaire ou pontage aorto coronarien sous CEC. Nous avons suivi la cinétique de TnIc par des dosages immunoenzymatique sur mini-vidas® avant et après la CEC, à H4 et H12 postopératoire puis tous les jours les 4 premiers jours. Le cutoff pour le diagnostic d'IDM post opératoire a été défini comme la valeur moyenne de troponine + deux déviations standards des patients indemnes de complications cardiaques. Résultats Les valeurs de TnIc en préopératoire étaient toutes inférieures au seuil de détection de la méthode de dosage (<0,01µg/l). Les valeurs de TnIc augmentent en postopératoire immédiat pour atteindre un maximum à H4 puis diminuent progressivement pour se normaliser après 4 à 5 jours. Les valeurs seuils ont été déterminées pour H0, H4,H12, H24, H48, H72, H96 et ont été respectivement 1.36, 2.58, 3.1, 3.23, 2.13, 1.53, 1.17 pour la chirurgie coronaire et 3.75, 5.39, 4.22, 3.41, 1.65, 1.3 1.19 pour la chirurgie valvulaire. Conclusion La connaissance de la cinétique de TnIc lors de chirurgie cardiaque non compliquée et la fixation de valeur seuil ou Cutoff permet aux cliniciens de distinguer entre dommage myocardique secondaire à la chirurgie et IDM. PMID:23396754

  13. Neutron irradiation of beryllium pebbles

    SciTech Connect

    Gelles, D.S.; Ermi, R.M.; Tsai, H.

    1998-03-01

    Seven subcapsules from the FFTF/MOTA 2B irradiation experiment containing 97 or 100% dense sintered beryllium cylindrical specimens in depleted lithium have been opened and the specimens retrieved for postirradiation examination. Irradiation conditions included 370 C to 1.6 {times} 10{sup 22} n/cm{sup 2}, 425 C to 4.8 {times} 10{sup 22} n/cm{sup 2}, and 550 C to 5.0 {times} 10{sup 22} n/cm{sup 2}. TEM specimens contained in these capsules were also retrieved, but many were broken. Density measurements of the cylindrical specimens showed as much as 1.59% swelling following irradiation at 500 C in 100% dense beryllium. Beryllium at 97% density generally gave slightly lower swelling values.

  14. Fracture surfaces of irradiated composites

    NASA Technical Reports Server (NTRS)

    Milkovich, Scott M.; Sykes, George F., Jr.; Herakovich, Carl T.

    1987-01-01

    Electron microscopy was used to analyze the fracture surfaces of T300/934 graphite/epoxy unidirectional off-axis tensile coupons which were subjected to 1.0-MeV electron radiation at a rate of 50 Mrad/h for a total dose of 10 Grad. Fracture surfaces from irradiated and nonirradiated specimens tested at 116 K, room temperature, and 394 K were analyzed to assess the influence of radiation and temperature on the mode of failure and variations in constituent material as a function of environmental exposure. Micrographs of fracture surfaces indicate that irradiated specimens are more brittle than nonirradiated specimens at low temperatures. However, at elevated temperatures the irradiated specimens exhibit significantly more plasticity than nonirradiated specimens.

  15. Effects of irradiation on PVC compounds

    NASA Astrophysics Data System (ADS)

    Bataille, P.; Ulkem, I.; Schreiber, H. P.

    1995-11-01

    PVC compounds containing CaCO 3 filler and plasticizers were prepared with or without a trifunctional acrylic crosslinking agent and irradiated by 60Co γ-rays under air or nitrogen atmosphere. The samples without crosslinking agent did not respond to irradiation. The mechanical properties of the other samples such as tensile strength, yield strength and % elongation showed a great sensitivity to irradiation. Lower values of Young's modulus were observed for samples irradiated in air compared with samples irradiated in nitrogen indicating the effect of atmosphere in the range of irradiation studied.

  16. Healing in the irradiated wound

    SciTech Connect

    Miller, S.H.; Rudolph, R. )

    1990-07-01

    Poor or nonhealing of irradiated wounds has been attributed to progressive obliterative endarteritis. Permanently damaged fibroblasts may also play an important part in poor healing. Regardless of the cause, the key to management of irradiated skin is careful attention to prevent its breakdown and conservative, but adequate, treatment when wounds are minor. When wounds become larger and are painful, complete excision of the wound or ulcer is called for and coverage should be provided by a well-vascularized nonparasitic distant flap.16 references.

  17. Modeling Solar Lyman Alpha Irradiance

    NASA Technical Reports Server (NTRS)

    Pap, J.; Hudson, H. S.; Rottman, G. J.; Willson, R. C.; Donnelly, R. F.; London, J.

    1990-01-01

    Solar Lyman alpha irradiance is estimated from various solar indices using linear regression analyses. Models developed with multiple linear regression analysis, including daily values and 81-day running means of solar indices, predict reasonably well both the short- and long-term variations observed in Lyman alpha. It is shown that the full disk equivalent width of the He line at 1083 nm offers the best proxy for Lyman alpha, and that the total irradiance corrected for sunspot effect also has a high correlation with Lyman alpha.

  18. The LasB Elastase of Pseudomonas aeruginosa Acts in Concert with Alkaline Protease AprA To Prevent Flagellin-Mediated Immune Recognition

    PubMed Central

    Casilag, Fiordiligie; Lorenz, Anne; Krueger, Jonas; Klawonn, Frank; Weiss, Siegfried

    2015-01-01

    The opportunistic pathogen Pseudomonas aeruginosa is capable of establishing severe and persistent infections in various eukaryotic hosts. It encodes a wide array of virulence factors and employs several strategies to evade immune detection. In the present study, we screened the Harvard Medical School transposon mutant library of P. aeruginosa PA14 for bacterial factors that modulate interleukin-8 responses in A549 human airway epithelial cells. We found that in addition to the previously identified alkaline protease AprA, the elastase LasB is capable of degrading exogenous flagellin under calcium-replete conditions and prevents flagellin-mediated immune recognition. Our results indicate that the production of two proteases with anti-flagellin activity provides a failsafe mechanism for P. aeruginosa to ensure the maintenance of protease-dependent immune-modulating functions. PMID:26502908

  19. The LasB Elastase of Pseudomonas aeruginosa Acts in Concert with Alkaline Protease AprA To Prevent Flagellin-Mediated Immune Recognition.

    PubMed

    Casilag, Fiordiligie; Lorenz, Anne; Krueger, Jonas; Klawonn, Frank; Weiss, Siegfried; Häussler, Susanne

    2015-10-26

    The opportunistic pathogen Pseudomonas aeruginosa is capable of establishing severe and persistent infections in various eukaryotic hosts. It encodes a wide array of virulence factors and employs several strategies to evade immune detection. In the present study, we screened the Harvard Medical School transposon mutant library of P. aeruginosa PA14 for bacterial factors that modulate interleukin-8 responses in A549 human airway epithelial cells. We found that in addition to the previously identified alkaline protease AprA, the elastase LasB is capable of degrading exogenous flagellin under calcium-replete conditions and prevents flagellin-mediated immune recognition. Our results indicate that the production of two proteases with anti-flagellin activity provides a failsafe mechanism for P. aeruginosa to ensure the maintenance of protease-dependent immune-modulating functions.

  20. The destiny of an unacknowledged trauma: the deferred retroactive effect of après-coup in the hidden Jewish children of wartime Belgium.

    PubMed

    Fohn, Adeline; Heenen-Wolff, Susann

    2011-02-01

    For almost 45 years, the experience of Jewish children who were hidden during World War II was considered to be of little importance, particularly with respect to what had taken place in the concentration camps. Their very history was ignored in the many accounts of the Holocaust. It was only at the end of the 1980s that their experience began to be thought of as potentially traumatic. In this paper, the authors report on their psychoanalytical research project concerning the psychological outcomes of those experiences that had remained concealed for such an extraordinarily long latency period. The results are based on the analysis of 60 accounts and on psychoanalytically-oriented group work. The authors show that the trauma experienced by those hidden children was triggered by the retroactive effect of a deferred action [après-coup].

  1. The SAMPL5 host-guest challenge: computing binding free energies and enthalpies from explicit solvent simulations by the attach-pull-release (APR) method

    NASA Astrophysics Data System (ADS)

    Yin, Jian; Henriksen, Niel M.; Slochower, David R.; Gilson, Michael K.

    2017-01-01

    The absolute binding free energies and binding enthalpies of twelve host-guest systems in the SAMPL5 blind challenge were computed using our attach-pull-release (APR) approach. This method has previously shown good correlations between experimental and calculated binding data in retrospective studies of cucurbit[7]uril (CB7) and β-cyclodextrin (βCD) systems. In the present work, the computed binding free energies for host octa acid (OA or OAH) and tetra-endo-methyl octa-acid (TEMOA or OAMe) with guests are in good agreement with prospective experimental data, with a coefficient of determination (R2) of 0.8 and root-mean-squared error of 1.7 kcal/mol using the TIP3P water model. The binding enthalpy calculations achieve moderate correlations, with R2 of 0.5 and RMSE of 2.5 kcal/mol, for TIP3P water. Calculations using the newly developed OPC water model also show good performance. Furthermore, the present calculations semi-quantitatively capture the experimental trend of enthalpy-entropy compensation observed, and successfully predict guests with the strongest and weakest binding affinity. The most populated binding poses of all twelve systems, based on clustering analysis of 750 ns molecular dynamics (MD) trajectories, were extracted and analyzed. Computational methods using MD simulations and explicit solvent models in a rigorous statistical thermodynamic framework, like APR, can generate reasonable predictions of binding thermodynamics. Especially with continuing improvement in simulation force fields, such methods hold the promise of making substantial contributions to hit identification and lead optimization in the drug discovery process.

  2. Gangrène de la main après injection accidentelle intra artérielle de floxacilline: à propos d’un cas

    PubMed Central

    Salama, Tarik; Aghoutane, El Mohtadi; Fezzazi, Rédouane El

    2016-01-01

    La floxacilline appartient à la classe des pénicillines bêta lactames. Dans notre contexte elle est très utilisée pour lutter contre les infections à germes Gram positif dont le staphylocoque doré. Cependant son utilisation doit être très prudente car elle n’est pas dénuée de complications. Nous rapportons l’observation d’un garçon de 6 ans opéré pour fracture de l’humérus. L’enfant a été mis sous floxacilline injectable après suspicion d’une infection sur matériel 2 mois après son opération. Le lendemain du début de l’antibiothérapie, l’enfant a présenté une ischémie aigue de la main droite. Il nous a alors été adressé pour prise en charge. Les explorations ont objectivé une obstruction de l’artère radiale. Une aponévrotomie de décharge a été réalisée et une héparinothérapie post opératoire a été démarrée. L’évolution a été marquée par une gangrène de toute la main. A travers cette observation nous voulons sensibiliser le personnel soignant sur le risque de survenue de cette complication désastreuse, et les mesures à prendre pour la prévenir. PMID:28293337

  3. Hair dosimetry following neutron irradiation.

    PubMed

    Lebaron-Jacobs, L; Gaillard-Lecanu, E; Briot, F; Distinguin, S; Boisson, P; Exmelin, L; Racine, Y; Berard, P; Flüry-Herard, A; Miele, A; Fottorino, R

    2007-05-01

    Use of hair as a biological dosimeter of neutron exposure was proposed a few years ago. To date, the (32)S(n,p)(32)P reaction in hair with a threshold of 2.5 MeV is the best choice to determine the fast neutron dose using body activation. This information is essential with regards to the heterogeneity of the neutron transfer to the organism. This is a very important parameter for individual dose reconstruction from the surface to the deeper tissues. This evaluation is essential to the adapted management of irradiated victims by specialized medical staff. Comparison exercises between clinical biochemistry laboratories from French sites (the CEA and COGEMA) and from the IRSN were carried out to validate the measurement of (32)P activity in hair and to improve the techniques used to perform this examination. Hair was placed on a phantom and was irradiated at different doses in the SILENE reactor (Valduc, France). Different parameters were tested: variation of hair type, minimum weight of hair sample, hair wash before measurement, delivery period of results, and different irradiation configurations. The results obtained in these comparison exercises by the different laboratories showed an excellent correlation. This allowed the assessment of a dose-activity relationship and confirmed the feasibility and the interest of (32)P measurement in hair following fast neutron irradiation.

  4. Irradiation enhancement of biomass conversion

    NASA Astrophysics Data System (ADS)

    Smith, G. S.; Kiesling, H. E.; Galyean, M. L.; Bader, J. R.

    The vast supply of cellulosic agricultural residues and industrial by-products that is produced each year is a prospective resource of biomass suitable for conversion to useful products such as feedstock for the chemicals industry and feedstuffs for the livestock industry. Conversions of such biomass is poor at present, and utilization is inefficient, because of physio-chemical barriers to biological degradation and (or) anti-quality components such as toxicants that restrict biological usages. Improvements in biodegradability of ligno-cellulosic materials have been accomplished by gamma-ray and electron-beam irradiation at intermediate dosage (˜ 50 Mrad; .5 MGy); but applications of the technology have been hampered by questionable interpretations of results. Recent research with organic wastes such as sewage sludge and straw suggests opportunity for important applications of irradiation technology in enhancement of biomass conversion. Data from experiments using irradiated straw as feed for ruminants are presented and discussed in relation to research on prospective usage of sewage products as feed for ruminants. Findings are discussed in regard to prospective applications in industrial fermentation processes. Possible usage of irradiation technology for destruction of toxicants in exotic plants is considered in regard to prospective new feedstuffs.

  5. Irradiance Variability of the Sun

    NASA Technical Reports Server (NTRS)

    Froehlich, Claus

    1990-01-01

    Direct measurements of the solar constant--the total irradiance at mean Sun-Earth distance--during the last ten years from satellites show variations over time scales from minutes to years and decades. At high frequencies the spectral power is determined by granulation, super- and mesogranulation. In the 5-minute range, moreover, it is dominated by power from the solar p-mode oscillations. Their power and frequencies change with time, yielding information about changes in the convection zone. During periods of several hours, the power is steadily increasing and may be partly due to solar gravity modes. The most important variance is in the range from days to several months and is related to the photospheric features of solar activity, decrease of the irradiance during the appearance of sunspots, and increasing by faculae and the magnetic network. Long-term modulation by the 11-year activity cycle are observed conclusively with the irradiance being higher during solar maximum. All these variations can be explained--at least qualitatively--by their manifestation on the photosphere. For the long-term changes, the simultaneous changes of the frequencies of solar p-mode oscillations suggest a more global origin of the variations. Indeed, it seems that the observed irradiance modulation is a true luminosity change with the magnetic cycle of the Sun.

  6. Microstructural processes in irradiated materials

    NASA Astrophysics Data System (ADS)

    Byun, Thak Sang; Morgan, Dane; Jiao, Zhijie; Almer, Jonathan; Brown, Donald

    2016-04-01

    These proceedings contain the papers presented at two symposia, the Microstructural Processes in Irradiated Materials (MPIM) and Characterization of Nuclear Reactor Materials and Components with Neutron and Synchrotron Radiation, held in the TMS 2015, 144th Annual Meeting & Exhibition at Walt Disney World, Orlando, Florida, USA on March 15-19, 2015.

  7. Food Irradiation Research and Technology

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Food Irradiation is a safe and effective U.S. Food and Drug Administration (FDA) approved process that can be used to disinfest or delay the maturation of fruits and vegetables, improve the microbiological safety of shellfish, eggs, raw meat and poultry, spices, and seeds used for sprouting. FDA ap...

  8. Food irradiation research and technology

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Food Irradiation is a safe and effective U.S. Food and Drug Administration (FDA) approved process that can be used to disinfest or delay the maturation of fruits and vegetables, improve the microbiological safety of shellfish, eggs, raw meat and poultry, spices, and seeds used for sprouting. FDA ap...

  9. Internal irradiation for cystic craniopharyngioma

    SciTech Connect

    Kobayashi, T.; Kageyama, N.; Ohara, K.

    1981-12-01

    The authors report the results of internal irradiation with labeled chromic phosphate (32P) and gold-198 (198Au) colloid in eight cases of cystic craniopharyngiomas. They used a newly developed dosimetric formula, by which the radiation dose at the cyst wall and at any point far from the radioactive source can be calculated. Ten courses of irradiation in eight patients were carried out by injection of either 32P or 198Au colloid into the cyst through an Ommaya drainage system that had been placed at craniotomy. Follow-up studies ranging from 13 to 156 months revealed that all cysts were effectively treated, with elimination of fluid or collapse of the cyst. This was confirmed by Conray cystography and/or computerized tomography. Not only the dose delivered to the wall but also the thickness of the cyst wall and the location of the cyst are important factors in planning internal irradiation. A safe and adequate dose to the cyst wall could range between 9000 to 30,000 rads for craniopharyngioma. This treatment is suitable for large cysts that are thought to be difficult to remove radically, recurrent cysts resistant to previous treatment, or multiple cysts. Internal irradiation may also be applicable in other cystic intracranial tumors if dosimetry is calculated accurately.

  10. Statistical criteria for characterizing irradiance time series.

    SciTech Connect

    Stein, Joshua S.; Ellis, Abraham; Hansen, Clifford W.

    2010-10-01

    We propose and examine several statistical criteria for characterizing time series of solar irradiance. Time series of irradiance are used in analyses that seek to quantify the performance of photovoltaic (PV) power systems over time. Time series of irradiance are either measured or are simulated using models. Simulations of irradiance are often calibrated to or generated from statistics for observed irradiance and simulations are validated by comparing the simulation output to the observed irradiance. Criteria used in this comparison should derive from the context of the analyses in which the simulated irradiance is to be used. We examine three statistics that characterize time series and their use as criteria for comparing time series. We demonstrate these statistics using observed irradiance data recorded in August 2007 in Las Vegas, Nevada, and in June 2009 in Albuquerque, New Mexico.

  11. Ultrasonic Transducer Irradiation Test Results

    SciTech Connect

    Daw, Joshua; Palmer, Joe; Ramuhalli, Pradeep; Keller, Paul; Montgomery, Robert; Chien, Hual-Te; Kohse, Gordon; Tittmann, Bernhard; Reinhardt, Brian; Rempe, Joy

    2015-02-01

    Ultrasonic technologies offer the potential for high-accuracy and -resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. Other ongoing efforts include an ultrasonic technique to detect morphology changes (such as crack initiation and growth) and acoustic techniques to evaluate fission gas composition and pressure. These efforts are limited by the lack of identified ultrasonic transducer materials capable of long term performance under irradiation test conditions. For this reason, the Pennsylvania State University (PSU) was awarded an ATR NSUF project to evaluate the performance of promising magnetostrictive and piezoelectric transducers in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 1021 n/cm2. The goal of this research is to characterize and demonstrate magnetostrictive and piezoelectric transducer operation during irradiation, enabling the development of novel radiation-tolerant ultrasonic sensors for use in Material Testing Reactors (MTRs). As such, this test is an instrumented lead test and real-time transducer performance data is collected along with temperature and neutron and gamma flux data. The current work bridges the gap between proven out-of-pile ultrasonic techniques and in-pile deployment of ultrasonic sensors by acquiring the data necessary to demonstrate the performance of ultrasonic transducers. To date, one piezoelectric

  12. Biological effects of ultraviolet irradiation on bees

    SciTech Connect

    Es`kov, E.K.

    1995-09-01

    The influence of natural solar and artificial ultraviolet irradiation on developing bees was studied. Lethal exposures to irradiation at different stages of development were determined. The influence of irradiation on the variability of the morphometric features of bees was revealed. 5 refs., 1 fig.

  13. Schedule and status of irradiation experiments

    SciTech Connect

    Rowcliffe, A.F.; Grossbeck, M.L.

    1997-04-01

    To provide an updated summary of the status of irradiation experiments for the neutron-interactive materials program. The current status of reactor irradiation experiments is presented in tables summarizing the experimental objectives, conditions, and schedule. Currently, the program has two irradiation experiments in reactor; and 8 experiments in the planning or design stages. Postirradiation examination and testing is in progress on 18 experiments.

  14. Laser irradiation to produce amorphous pharmaceuticals.

    PubMed

    Titapiwatanakun, Varin; Tankul, Junlathip; Basit, Abdul W; Gaisford, Simon

    2016-11-30

    Using a high-power CO2 laser to irradiate powder beds, it was possible to induce phase transformation to the amorphous state. Irradiation of a model drug, indometacin, resulted in formation of a glass. Varying the settings of the laser (power and raster speed) was shown to change the physicochemical properties of the glasses produced and all irradiated glasses were found to be more stable than a reference glass produced by melt-quenching. Irradiation of a powder blend of paracetamol and polyvinylpyrrolidone K30 was found to produce a solid amorphous dispersion. The results suggest that laser-irradiation might be a useful method for making amorphous pharmaceuticals.

  15. Food irradiation development in Pakistan

    NASA Astrophysics Data System (ADS)

    Khan, I.

    The large scale trials were held to extend the storage life of potatoes, onions and dry fruits by gamma radiation. It was concluded that radiation preservation of potatoes and onions was much cheaper as compared to conventional methods. A dose of 1 kGy can control the insects in dry fruits and nuts. The consumers' acceptability and market testing performed during the last four years are also conducive to the commercialization of the technology in this country. The Government of Pakistan has accorded clearance for the irradiation of some food items like potatoes, onions, garlic and spices for human consumption. The Pakistan Radiation Services (PARAS), the commercial irradiator (200 Kci) at Lahore, has already started functioning in April, 1987. It is planned to start large scale sterilization of spices by gamma radiation in PARAS shortly.

  16. Particular applications of food irradiation fresh produce

    NASA Astrophysics Data System (ADS)

    Prakash, Anuradha

    2016-12-01

    On fresh fruits and vegetables, irradiation at low and medium dose levels can effectively reduce microbial counts which can enhance safety, inhibit sprouting to extend shelf-life, and eliminate or sterilize insect pests which can serve to facilitate trade between countries. At the dose levels used for these purposes, the impact on quality is negligible. Despite the fact that regulations in many countries allow the use of irradiation for fresh produce, the technology remains under-utilized, even in the light of an increase in produce related disease outbreaks and the economic benefits of extended shelf life and reduced food waste. Putative concerns about consumer acceptance particularly for produce that is labeled as irradiated have deterred many companies from using irradiation and retailers to carry irradiated produce. This section highlights the commercial use of irradiation for fresh produce, other than phytosanitary irradiation which is covered in supplementary sections.

  17. Blood Irradiator Interactive Tool Beta Version

    SciTech Connect

    Howington, John; Potter, Charles; DeGroff, Tavias; Best, Derek

    2016-04-15

    The “Blood Irradiator Interactive Tool” compares a typical Cs-137 Blood Irradiator with that of the capabilities of an average X-ray Irradiator. It is designed to inform the user about the potential capabilities that an average X-ray Irradiator could offer them. Specifically the tool compares the amount of blood bags that can be irradiated by the users’ machine with that of the average X-ray capability. It also forcasts the amount of blood that can be irradiated on yearly basis for both the users’ machine and an average X-ray Device. The Average X-ray capabilities are taken from the three X-ray devices currently on the market: The RS 3400 Rad Source X-ray Blood Irradiator and both the 2.0L and 3.5 L versions of the Best Theratronis Raycell MK2

  18. Future Satellite Observations of Solar Irradiance

    NASA Technical Reports Server (NTRS)

    Cahalan, R. F.; Rottman, G.; Woods, T.; Lawrence, G.; Harder, J.; McClintock, W.; Kopp, G.

    2003-01-01

    Required solar irradiance measurements for climate studies include those now being made by the Total Irradiance Monitor (TIM) and the Spectral Irradiance Monitor (SIM) onboard the SORCE satellite, part of the Earth Observing System fleet of NASA satellites. Equivalent or better measures of Total Solar Irradiance (TSI) and Spectral Solar Irradiance (SSI, 200 to 2000 nm) are planned for the post-2010 satellites of the National Polar-orbiting Operational Environmental Satellite System ("OESS). The design life of SORCE is 5 years, so a "Solar Irradiance Gap Filler" EOS mission is being planned for launch in the 2007 time frame, to include the same TSI and SSI measurements. Besides avoiding any gap, overlap of the data sources is also necessary for determination of possible multi-decadal trends in solar irradiance. We discuss these requirements and the impacts of data gaps, and data overlaps, that may occur in the monitoring of the critical solar radiative forcing.

  19. Microstructure evolution in irradiated materials

    SciTech Connect

    Caturla, M

    1999-11-30

    Study the interaction of defects produced during irradiation or deformation of a metal with the microstructure of that particular material, such as dislocations and grain boundaries. In particular we will study the interaction of dislocation with interstitial loops and stacking fault tetrahedral, and the production of displacement cascades close to dislocations and grain boundaries. The data obtained from these simulations will be used as input to diffusion models and dislocation dynamics models.

  20. RERTR-8 Irradiation Summary Report

    SciTech Connect

    D. M. Perez; M. A. Lillo; G. S. Chang; G. A. Roth; N. E. Woolstenhulme; D. M. Wachs

    2011-12-01

    The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-8, was designed to test monolithic mini-fuel plates fabricated via hot isostatic pressing (HIP), the effect of molybdenum (Mo) content on the monolithic fuel behavior, and the efficiency of ternary additions to dispersion fuel particles on the interaction layer behavior at higher burnup. The following report summarizes the life of the RERTR-8 experiment through end of irradiation, including as-run neutronic analysis, thermal analysis and hydraulic testing results.

  1. RERTR-6 Irradiation Summary Report

    SciTech Connect

    D. M. Perez; M. A. Lillo; G. S. Chang; G. A. Roth; N. E. Woolstenhulme; D. M. Wachs

    2011-12-01

    The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-6 was designed to evaluate several modified fuel designs that were proposed to address the possibility of breakaway swelling due to porosity within the (U. Mo) Al interaction product observed in the full-size plate tests performed in Russia and France1. The following report summarizes the life of the RERTR-6 experiment through end of irradiation, including as-run neutronic analyses, thermal analyses and hydraulic testing results.

  2. Microstructural processes in irradiated materials

    SciTech Connect

    Byun, Thak Sang; Morgan, Dane; Jiao, Zhijie; Almer, Jonathan; Brown, Donald

    2016-04-01

    This is an editorial article (preface) for the publication of symposium papers in the Journal of Nuclear materials: These proceedings contain the papers presented at two symposia, the Microstructural Processes in Irradiated Materials (MPIM) and Characterization of Nuclear Reactor Materials and Components with Neutron and Synchrotron Radiation, held in the TMS 2015, 144th Annual Meeting & Exhibition at Walt Disney World, Orlando, Florida, USA on March 15–19, 2015.

  3. FFTF utilization for irradiation testing

    SciTech Connect

    Corrigan, D.C.; Julyk, L.J.; Hoth, C.W.; McGuire, J.C.; Sloan, W.R.

    1980-01-01

    FFTF utilization for irradiation testing is beginning. Two Fuels Open Test Assemblies and one Vibration Open Test Assembly, both containing in-core contact instrumentation, are installed in the reactor. These assemblies will be used to confirm plant design performance predictions. Some 100 additional experiments are currently planned to follow these three. This will result in an average core loading of about 50 test assemblies throughout the early FFTF operating cycles.

  4. Radical Irradiation of Extracranial Oligometastases

    PubMed Central

    Salama, Joseph K.; Milano, Michael T.

    2014-01-01

    Advances in radiotherapy planning and delivery have been used to treat patients with limited metastatic disease. With these techniques, high rates of treated metastasis control and low toxicity have been reported. Some patients have long disease-free intervals after radiotherapy similar to those seen after surgical resection. Ongoing studies will determine the benefit of these irradiation techniques to treat limited metastases, identify appropriate candidates, and assist in integrating these treatments into management strategies for specific diseases. PMID:25113765

  5. Licensing a new industrial irradiator.

    PubMed

    Bates, Nicolas K; Entwistle, Frederick B

    2010-02-01

    After nearly three decades of medical product sterilization, 3M launched a major new project to build and license an irradiator facility. 3M Corporate Health Physics was responsible for the licensing aspect of this project. The licensing process consisted of six amendments, over 30 submissions to the U.S. Nuclear Regulatory Commission (U.S. NRC) and four U.S. NRC site visits. It took approximately 22 months to complete. The six license amendments are reviewed and several of the submissions are discussed. These include 3M's response to the U.S. NRC's interest in the shielding calculations used for the bioshield, the development of a protocol of radiation safety system test methods, and an analysis to show that a dropped cask during loading operations would not fall on sealed sources. A number of lessons were learned during the course of licensing the new irradiator. Among these were the importance of understanding the U.S. NRC license reviewer's perspective, the need to thoroughly review the irradiator manufacturer's licensing package during project negotiations, the benefits of leaving the Health Physics Office and meeting with the non-health physicists involved in the project, and the necessity of maintaining the solid relationships that already existed with the site Radiation Safety Officer and Sterilization Engineer.

  6. Status of Post Irradiation Examination of FCAB and FCAT Irradiation Capsules

    SciTech Connect

    Field, Kevin G.; Yamamoto, Yukinori; Howard, Richard H.

    2016-09-29

    A series of irradiation programs are ongoing to address the need for determining the radiation tolerance of FeCrAl alloys. These irradiation programs, deemed the FCAT and FCAB irradiation programs, use the High Flux Isotope Reactor (HFIR) to irradiate second generation wrought FeCrAl alloys and early-generation powder-metallurgy (PM) oxide dispersion-strengthened (ODS) FeCrAl alloys. Irradiations have been or are being performed at temperatures of 200°C, 330°C, and 550°C from doses of 1.8 dpa up to 16 dpa. Preliminary post-irradiation examination (PIE) on low dose (<2 dpa) irradiation capsules of tensile specimens has been performed. Analysis of co-irradiated SiC thermometry have shown reasonable matching between the nominal irradiation temperatures and the target irradiation temperatures. Room temperature tensile tests have shown typical radiation-induced hardening and embrittlement at irradiations of 200°C and 330°C, but a propensity for softening when irradiated to 550°C for the wrought alloys. The PM-ODS FeCrAl specimens showed less hardening compared to the wrought alloys. Future PIE includes high temperature tensile tests on the low dose irradiation capsules as well as the determination of reference fracture toughness transition temperature, To, in alloys irradiated to 7 dpa and higher.

  7. Étude des anomalies chromosomiques après radiothérapie chez des patients traités pour lymphome malin non-Hodgkinien

    NASA Astrophysics Data System (ADS)

    Mahe, M. A.; André, M. J.; Moyon, E.; Le Mevel, A.; Soubeyran, P.; Hamidou, M.; Milpied, N.; Bourdin, S.; Cuillière, J. C.; Chatal, J. F.

    1998-04-01

    Structural chromosome defects were evaluated in the lymphocytes of 30 patients (pts) who had undergone radiotherapy for non Hodgkin's lymphoma (NHL). Twelve had received 20 Grays (Gy) over the abdomen (group I), 12 whole body irradiation at 1.5 Gy (group II) and 6 whole body irradiation at 15 Gy (group III). A cohort of 468 unirradiated pts served as controls. For the irradiated group, 7% of cells had aberrations compared to 0.4% in controls {P <10-6}. The frequency of abnormal cells was statistically higher in group I (12%) than in group II (3.5%) and III (2.5%) . In group I, frequency of aberrations was statistically higher in pts who had additionnal extra-abdominal involved field irradiation, those with evolutive NHL and those receiving chemotherapy at the time of the cytogenetic analysis. Les aberrations chromosomiques ont ,été, mesurées sur les lymphocytes de 30 patients (pts) irradiés pour lymphome malin non-hodgkinien (LNH) selon 3 modalités : 20 Grays (Gy) sur l'abdomen (groupe I : 12 pts), Irradiation corporelle totale 1,5 Gy (groupe II : 12 pts), ou 15 Gy (groupe III : 6 pts). Une population non irradiée de 468 pts a servi de témoin. Dans le groupe irradié, 7 % des cellules présentaient des anomalies contre 0,4 % dans le groupe témoin {P <10-6}. Les aberrations ,étaient statistiquement plus nombreuses dans le groupe I (12 % des cellules) que dans les groupes II (3,5 %) et III (2,5 %). Dans le groupe I, les anomalies , étaient statistiquement plus fréquentes chez les pts ayant eu une irradiation localisée extra-abdominale en complément de celle de l'abdomen ainsi que chez ceux en rechute de leur LNH et ceux recevant une chimiothérapie lors de l',étude cytogénétique.

  8. Validation of Meteornom solar irradiation data for three regions in Brazil

    NASA Astrophysics Data System (ADS)

    Pereira, E. B.; Teixeira, V. A.; Martins, F. R.

    2015-12-01

    This work is a part of a study to identify available and reliable sources of solar irradiation data in Brazil - with a strong focus on their relevance for PV and CSP applications. One of these sources is the Meteonorm . Meteonorm is a comprehensive meteorological reference. It gives access to a catalogue of solar radiation data and meteorological data for solar applications and system design at any desired location in the world. The current report provides an evaluation of the solar irradiation data derived from version 7.0 of the Meteonorm software for Brazil. This evaluation was made by using the observation data of horizontal global solar irradiation from the SONDA/BSRN network for Petrolina (PTR), Brasilia (BRB), and São Martinho do Serra (SMS). These sites were chosen based on a careful data quality control, absence of daily gaps, and less than 60% of missing data per month. The Meteonorm data were generated with real input monthly average for each selected validation sites for the years 2011, 2013, and 2014. The analysis was performed by relative and cumulative frequency of annual and seasonal solar irradiance, based on the methodology proposed by Pierre Inechen, 2006. The results showed little interannual variability for the validation sites and presented a recurrent occurrence of the value of 1000W.m-2 for stations PTR and BRB. The Meteonorm was able to represent the high frequencies in these locations, however, presented an interannual variation greater than observed, and an overestimation of values. As for the seasonal analysis, it was possible to verify that the quarters which varied the most from one year to the next were the Dec-Jan-Feb and Sep-Oct-Nov in BRB station; Dec-Jan-Feb and Mar-Apr-May in the PTR station; and Dec-Jan-Feb in the SMS station. The Meteornorm was able identify the months of highest and lowest variability in the BRB and SMS stations, except PTR station which yielded a large

  9. 2-alkylcyclobutanones as irradiation dose indicators in irradiated ground beef patties.

    PubMed

    Gadgil, Priyadarshini; Hachmeister, Kathleen A; Smith, J Scott; Kropf, Donald H

    2002-09-25

    Alkylcyclobutanones have been recognized as chemical markers of irradiated lipid-containing foods since 1970. They are important because they are produced solely as a result of irradiation and not any other processing method. This study investigated the formation of 2-dodecylcyclobutanone (2-DCB) and 2-tetradec-5'-enylcyclobutanone (2-TDCB) in irradiated ground beef patties from commercial and noncommercial sources. Patties were irradiated using a (60)C source (gamma-irradiation) and electron beam irradiation, at five targeted absorbed doses of 0.5, 1.0, 2.5, 5.0, and 7.0 kGy. Commercially available irradiated patties were also studied. A supercritical fluid extraction (SFE) procedure was optimized and used for the extraction and isolation of the alkylcyclobutanones. Samples can be used for extraction without a prior cleanup step, which makes this procedure rapid and convenient to use. Identification and quantitation of the cyclobutanones were done by gas chromatography-mass spectroscopy. 2-DCB was detected in all of the irradiated samples (including commercial patties), and its concentration increased linearly with the irradiation dose. Electron beam irradiation produced a greater amount of 2-DCB compared to gamma-irradiation at dose levels >2.5 kGy. 2-TDCB was detected only at the two higher irradiation doses, whereas both marker compounds were not detected in the non-irradiated samples.

  10. Activation of CK1ε by PP2A/PR61ε is required for the initiation of Wnt signaling

    PubMed Central

    Curto, J; Padilla, M; Villarroel, A; Yang, J; de Herreros, AG; Duñach, M

    2016-01-01

    Canonical Wnt signaling induces the stabilization of β-catenin, its translocation to the nucleus and the activation of target promoters. This pathway is initiated by the binding of Wnt ligands to the Frizzled receptor, the association of the LRP5/6 coreceptor and the formation of a complex comprising Dvl-2, Axin and protein kinases CK1α, ε, γ and GSK3. Among these, activation of CK1ε, constitutively bound to LRP5/6 through p120-catenin, is required for the association of the rest of the components. We describe here that CK1ε is activated by the PP2A/PR61ε phosphatase. Binding of Wnt ligands promotes the interaction of LRP5/6-associated CK1ε with Frizzled-bound PR61ε regulatory subunit, facilitating the access of PP2A catalytic subunit to CK1ε and its activation, what enables the recruitment of Dvl-2 to the receptor complex and the initiation of the Wnt pathway. Our results uncover the mechanism of activation of the canonical Wnt pathway by its ligands. PMID:27321178

  11. L'endométriose pariétale cicatricielle après césarienne: une entité rare

    PubMed Central

    El Fahssi, Mohammed; Lomdo, Massama; Bounaim, Ahmed; Ali, Abdelmounaim Ait; Sair, Khalid

    2016-01-01

    L'endométriose de la paroi est une entité clinique rare, dont la physiopathologie demeure imprécise. Elle survient le plus souvent après une intervention chirurgicale gynécologique ou obstétricale. Nous rapportons le cas d'une patiente présentant une douleur cyclique, au niveau de la cicatrice de césarienne, Avec à l'examen clinique une masse de 5cm localisée au niveau de la fosse iliaque droite. la tomodensitométrie montre une masse de densité tissulaire de 45mm de grand axe. D'où la décision d'excision large de la lésion dont l’étude anatomopathologique confirme le diagnostic d'endométriose pariétale. Les suites postopératoires étaient simples avec un recul de 20 mois sans récidive de la masse ni de la douleur. A travers notre cas, nous insisterons sur les caractéristiques de cette pathologie, ce qui permettra au praticien de comprendre l'intérêt du diagnostic et de la prise en charge précoce de cette affection ainsi que la possibilité de sa prévention au cours de chaque chirurgie gynécologique ou obstétricale. PMID:27642418

  12. Complete Protection against Influenza Virus H1N1 Strain A/PR/8/34 Challenge in Mice Immunized with Non-Adjuvanted Novirhabdovirus Vaccines

    PubMed Central

    Rouxel, Ronan N.; Mérour, Emilie; Biacchesi, Stéphane; Brémont, Michel

    2016-01-01

    Novirhabdoviruses like Viral Hemorrhagic Septicemia Virus (VHSV) and Infectious Hematopoietic Necrosis Virus (IHNV) are fish-infecting Rhabdoviruses belonging to the Mononegavirales order. By reverse genetics, we previously showed that a recombinant VHSV expressing the West Nile Virus (WNV) E glycoprotein could serve as a vaccine platform against WNV. In the current study, we aimed to evaluate the potential of the Novirhabdovirus platform as a vaccine against influenza virus. Recombinant Novirhabdoviruses, rVHSV-HA and rIHNV-HA, expressing at the viral surface the hemagglutinin HA ectodomain were generated and used to immunized mice. We showed that mice immunized with either, rVHSV-HA or rIHNV-HA, elicited a strong neutralizing antibody response against influenza virus. A complete protection was conferred to the immunized mice when challenged with a lethal dose of influenza H1N1 A/PR/8/34 virus. Furthermore we showed that although acting as inert antigen in mice, since naturally inactivated over 20°C, mice immunized with rVHSV-HA or rIHNV-HA in the absence of adjuvant were also completely protected from a lethal challenge. Novirhabdoviruses platform are of particular interest as vaccines for mammals since they are cost effective to produce, relatively easy to generate and very effective to protect immunized animals. PMID:27711176

  13. Activation of CK1ɛ by PP2A/PR61ɛ is required for the initiation of Wnt signaling.

    PubMed

    Vinyoles, M; Del Valle-Pérez, B; Curto, J; Padilla, M; Villarroel, A; Yang, J; de Herreros, A G; Duñach, M

    2017-01-19

    Canonical Wnt signaling induces the stabilization of β-catenin, its translocation to the nucleus and the activation of target promoters. This pathway is initiated by the binding of Wnt ligands to the Frizzled receptor, the association of the LRP5/6 co-receptor and the formation of a complex comprising Dvl-2, Axin and protein kinases CK1α, ɛ, γ and GSK3. Among these, activation of CK1ɛ, constitutively bound to LRP5/6 through p120-catenin, is required for the association of the rest of the components. We describe here that CK1ɛ is activated by the PP2A/PR61ɛ phosphatase. Binding of Wnt ligands promotes the interaction of LRP5/6-associated CK1ɛ with Frizzled-bound PR61ɛ regulatory subunit, facilitating the access of PP2A catalytic subunit to CK1ɛ and its activation, what enables the recruitment of Dvl-2 to the receptor complex and the initiation of the Wnt pathway. Our results uncover the mechanism of activation of the canonical Wnt pathway by its ligands.

  14. Thermal analysis applied to irradiated propolis

    NASA Astrophysics Data System (ADS)

    Matsuda, Andrea Harumi; Machado, Luci Brocardo; del Mastro, Nélida Lucia

    2002-03-01

    Propolis is a resinous hive product, collected by bees. Raw propolis requires a decontamination procedure and irradiation appears as a promising technique for this purpose. The valuable properties of propolis for food and pharmaceutical industries have led to increasing interest in its technological behavior. Thermal analysis is a chemical analysis that gives information about changes on heating of great importance for technological applications. Ground propolis samples were 60Co gamma irradiated with 0 and 10 kGy. Thermogravimetry curves shown a similar multi-stage decomposition pattern for both irradiated and unirradiated samples up to 600°C. Similarly, through differential scanning calorimetry , a coincidence of melting point of irradiated and unirradiated samples was found. The results suggest that the irradiation process do not interfere on the thermal properties of propolis when irradiated up to 10 kGy.

  15. Methods for detection of irradiation of spices.

    PubMed

    Sjöberg, A M; Manninen, M; Härmälä, P; Pinnioja, S

    1990-02-01

    Three types of methods for the identification of irradiation of spices were tested as potential control methods. The methods were microbiological, combining a direct epifluorescent filter technique (DEFT) with a total aerobic plate count (APC), a chemiluminescence method and chemical gas-chromatographic (GC) and GC mass-spectrometric (MS) methods for analysis of volatile oils of spices isolated by steam distillation. Twelve samples of spices, mainly peppers, were analysed before and after gamma-irradiation with doses of 10 and 50 kGy. The chemiluminescence measurements were performed before the irradiation and 10 and 100 days after the irradiation. The best methods for control purposes were the microbiological (DEFT + APC) methods combined with chemiluminescence measurements. No differences were detected between the irradiated and non-irradiated samples with the chemical methods.

  16. HRB-22 irradiation phase test data report

    SciTech Connect

    Montgomery, F.C.; Acharya, R.T.; Baldwin, C.A.; Rittenhouse, P.L.; Thoms, K.R.; Wallace, R.L.

    1995-03-01

    Irradiation capsule HRB-22 was a test capsule containing advanced Japanese fuel for the High Temperature Test Reactor (HTTR). Its function was to obtain fuel performance data at HTTR operating temperatures in an accelerated irradiation environment. The irradiation was performed in the High Flux Isotope Reactor (HFIR) at the Oak Ridge National Laboratory (ORNL). The capsule was irradiated for 88.8 effective full power days in position RB-3B of the removable beryllium (RB) facility. The maximum fuel compact temperature was maintained at or below the allowable limit of 1300{degrees}C for a majority of the irradiation. This report presents the data collected during the irradiation test. Included are test thermocouple and gas flow data, the calculated maximum and volume average temperatures based on the measured graphite temperatures, measured gaseous fission product activity in the purge gas, and associated release rate-to-birth rate (R/B) results. Also included are quality assurance data obtained during the test.

  17. Early esophageal carcinoma treated with intracavitary irradiation

    SciTech Connect

    Hishikawa, Y.; Tanaka, S.; Miura, T.

    1985-08-01

    Five patients with early esophageal carcinoma were treated by 6-12 Gy of intracavitary irradiation following 50-60 Gy of external irradiation as a boost therapy. Surgery was not performed in these cases. None of the patients had local recurrence after radiation therapy, as demonstrated by esophagography and endoscopy. Three patients have been alive for 1-3 years 10 months. Esophageal ulceration induced by intracavitary irradiation has occurred in three of the five patients; however, intracavitary irradiation is still a beneficial treatment because of its efficacy in controlling local lesions and because radiation ulceration can eventually be cured. Intracavitary irradiation is recommended to follow external irradiation as a boost therapy for the treatment of early esophageal carcinoma.

  18. A new multipurpose gamma-irradiation facility

    NASA Astrophysics Data System (ADS)

    Huebner, G.

    In the past 3 yr much work has been done in the G.D.R. on food irradiation. The experiments have shown that this treatment gives favourable results in many products such as spices, onions, potatoes, chicken, animal feeds, fodder yeast, drugs and vaccines. Economic aspects of food irradiation require the effective use of an irradiation plant and cobalt-60. Therefore, a new multipurpose irradiation facility was developed, applicable as an onion irradiator with a capacity of about 15 ton/h and for the simultaneous irradiation of different products (spices, animal feed, chicken, etc.) in closed product ☐es with a size of 1.2 m x 1.0 m x 1.2 m. A microcomputer controls the transport of product ☐es around the gamma sources.

  19. Irradiation preservation of seafood: Literature review

    SciTech Connect

    Molton, P.M.

    1987-10-01

    The application of gamma-irradiation for extending the shelf life of seafood has been of interest for many years. This report reviews a number of studies on seafood irradiation conducted over the past several years. Topics covered include seafood irradiation techniques and dosages, species applicability and differences, the effects of packaging on seafood preservation, and changes in organoleptic acceptability as a result of irradiation. Particular attention is given to radiation effects (likely and unlikely) of concern to the public. These include the potential for generation of toxic chemical products, botulinum toxin production, and other health concerns. No scientifically defensible evidence of any kind was found for any harmful effect of irradiation of seafoods at the doses being considered (less than 300 krad), and all indications are that irradiation is an acceptable and needed additional tool for seafood preservation. 49 refs., 14 figs., 14 tabs.

  20. EPR Investigation of Irradiated Curry Powder

    SciTech Connect

    Duliu, O. G.; Ali, S. I.; Georgescu, R.

    2007-04-23

    Gamma-ray irradiated curry powder, a well priced oriental spice was investigated in order to establish the ability of EPR to detect the presence and time stability of free irradiation free-radicals. Accordingly, curry powder aliquots were irradiated with gradually increasing absorbed doses up to 11.3 kGy. The EPR spectra of all irradiated samples show the presence of al last two different species of free radicals, whose concentration increased monotonously with the absorbed doses. A 100 deg. C isothermal annealing of irradiated samples has shown a differential reduction of amplitude of various components of the initial spectra, but even after 3.6 h of thermal treatment, the remaining amplitude represents no less then 30% of the initial ones. The same peculiarities have been noticed after more than one year storage at room temperature, all of them being very useful in establishing the existence of any previous irradiation treatment.

  1. Irradiation Testing of Ultrasonic Transducers

    SciTech Connect

    Daw, Joshua; Tittmann, Bernhard; Reinhardt, Brian; Kohse, Gordon E.; Ramuhalli, Pradeep; Montgomery, Robert O.; Chien, Hual-Te; Villard, Jean-Francois; Palmer, Joe; Rempe, Joy

    2014-07-30

    Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of single, small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. Other efforts include an ultrasonic technique to detect morphology changes (such as crack initiation and growth) and acoustic techniques to evaluate fission gas composition and pressure. These efforts are limited by the lack of existing knowledge of ultrasonic transducer material survivability under irradiation conditions. For this reason, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate promising magnetostrictive and piezoelectric transducer performance in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 1021 n/cm2 (E> 0.1 MeV). The goal of this research is to characterize magnetostrictive and piezoelectric transducer survivability during irradiation, enabling the development of novel radiation tolerant ultrasonic sensors for use in Material and Test Reactors (MTRs). As such, this test will be an instrumented lead test and real-time transducer performance data will be collected along with temperature and neutron and gamma flux data. The current work bridges the gap between proven out-of-pile ultrasonic techniques and in-pile deployment of ultrasonic sensors by acquiring the data necessary to demonstrate the performance of ultrasonic transducers.

  2. Irradiation Testing of Ultrasonic Transducers

    SciTech Connect

    Daw, Joshua; Tittmann, Bernhard; Reinhardt, Brian; Kohse, Gordon E.; Ramuhalli, Pradeep; Montgomery, Robert O.; Chien, Hual-Te; Villard, Jean-Francois; Palmer, Joe; Rempe, Joy

    2013-12-01

    Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of single, small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. Other efforts include an ultrasonic technique to detect morphology changes (such as crack initiation and growth) and acoustic techniques to evaluate fission gas composition and pressure. These efforts are limited by the lack of existing knowledge of ultrasonic transducer material survivability under irradiation conditions. For this reason, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate promising magnetostrictive and piezoelectric transducer performance in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 1021 n/cm2 (E> 0.1 MeV). The goal of this research is to characterize magnetostrictive and piezoelectric transducer survivability during irradiation, enabling the development of novel radiation tolerant ultrasonic sensors for use in Material and Test Reactors (MTRs). As such, this test will be an instrumented lead test and real-time transducer performance data will be collected along with temperature and neutron and gamma flux data. The current work bridges the gap between proven out-of-pile ultrasonic techniques and in-pile deployment of ultrasonic sensors by acquiring the data necessary to demonstrate the performance of ultrasonic transducers.

  3. Ion irradiation of astrophysical ices

    NASA Astrophysics Data System (ADS)

    Palumbo, M. E.; Baratta, G. A.; Fulvio, D.; Garozzo, M.; Gomis, O.; Leto, G.; Spinella, F.; Strazzulla, G.

    2008-02-01

    Ices, silicates and carbonaceous materials have been detected in several astrophysical environments such as interstellar molecular clouds, comets, and planetary surfaces. These solids are continuously exposed to ion irradiation and UV photolysis. Our knowledge on the properties of solids and molecules and on the modification induced by fast ions (keV-MeV) and UV photons is mainly based on laboratory experiments and on the comparison of experimental results with observations. Here we will give a few examples of the role of laboratory experiments to our understanding of the physical and chemical properties of ices in space.

  4. Thymus irradiation for myasthenia gravis

    SciTech Connect

    Currier, R.D.; Routh, A.; Hickman, B.T.; Douglas, M.A.

    1983-01-01

    Twenty-eight patients with progressive myasthenia gravis without thymoma received treatment of 3000 rads (30 Gy) to the anterior mediastinum, and a followup was conducted for five to 18 years. Twenty-four patients had generalized myasthenia, and four had ocular myasthenia gravis. Twenty patients with generalized myasthenia survived the several month post-treatment period and improved, but four died during that period. The improvement lasted a median of 1.5 years, and older patients had longer remissions than younger patients. The four patients who had ocular myasthenia did not change after treatment. Mediastinal irradiation produces a temporary remission in generalized myasthenia.

  5. Food irradiation and airline catering

    SciTech Connect

    Preston, F.S.

    1988-04-01

    Food poisoning from contaminated airline food can produce serious consequences for airline crew and passengers and can hazard flight. While irradiation of certain foodstuffs has been practised in a number of countries for some years, application of the process has not been made to complete meals. This paper considers the advantages, technical considerations, costs and possible application to airline meals. In addition, the need to educate the public in the advantages of the process in the wake of incidents such as Chernobyl is discussed.

  6. Electron spin resonance identification of irradiated fruits

    NASA Astrophysics Data System (ADS)

    Raffi, Jacques J.; Agnel, Jean-Pierre L.

    The electron spin resonance spectrum of achenes, pips, stalks and stones from irradiated fruits (strawberry, raspberry, red currant, bilberry, apple, pear, fig, french prune, kiwi, water-melon and cherry) always displays, just after γ-treatment, a weak triplet ( aH≈30 G) due to a cellulose radical; its left line (lower field) can be used as an identification test of irradiation, at least for strawberries, rapsberries, red currants or bilberries irradiated in order to improve their storage time.

  7. Food irradiation facilities: Requirements and technical aspects

    NASA Astrophysics Data System (ADS)

    Mittendorfer, Josef

    2016-12-01

    This survey presents some aspects and requirement for food irradiation facilities. Topics like radiation source, dose ranges and dose rate are discussed, together with logistics and operational considerations

  8. Aqueous marker penetration into ion irradiated polyimide

    NASA Astrophysics Data System (ADS)

    Fink, D.; Müller, M.; Petrov, A.; Klett, R.; Palmetshofer, L.; Hnatowicz, V.; Vacik, J.; Cervena, J.; Chadderton, L. T.

    2002-05-01

    The penetration of aqueous 6Li + markers into low energy ion irradiated polyimide (PI) foils was examined by the neutron depth profiling technique in combination with a modified tomographic approach. The ion irradiation always leads to an enhancement in marker uptake. After irradiation at low fluence the marker profiles follow the nuclear damage distribution even in three dimensions. At elevated fluences saturation in the marker uptake is clearly seen. The polymer's penetrant uptake can be described well by regular diffusion, with nuclear damage centres acting as saturable traps. These observations are strikingly different from the marker penetration into high-energy heavy-ion irradiated PI.

  9. Free radical kinetics on irradiated fennel

    NASA Astrophysics Data System (ADS)

    Yamaoki, Rumi; Kimura, Shojiro; Ohta, Masatoshi

    2008-09-01

    Herein, an electron spin resonance study on the behavior of organic radicals in fennel before and after irradiation is reported. The spectrum of irradiated fennel composed of the spectrum component derived from the un-irradiated sample (near g=2.005) and the spectra components derived from carbohydrates. The time decay of intensity spectral components was well explained by first-order kinetics with a variety of rate constants. Especially, the signal at near g=2.02 ascribed to stable cellulose-derivative components is expected to be a good indicator in the identification of irradiated plant samples.

  10. Analytical screening studies on irradiated food packaging.

    PubMed

    Driffield, M; Bradley, E L; Leon, I; Lister, L; Speck, D R; Castle, L; Potter, E L J

    2014-01-01

    Foods may be irradiated in their final packaging and this process may affect the composition of the packaging and in turn affect the migration of substances into food. Headspace and liquid injection GC-MS and HPLC with time-of-flight MS have been used to identify and estimate levels of radiolytic products in irradiated finished plastic packaging materials. Fifteen retail packaging materials were studied. Investigations were carried out into the effect of different irradiation types (gamma and electron beam), irradiation doses (1, 3, 7 and 10 kGy) and dose rates (5 kGy s(-1) for electron beam and 0.4 and 1.85 kGy h(-1) for gamma) on the radiolytic products. Any differences seen in comparing the two ionising radiation types were attributed largely to the very different dose rates; for electron beam a 10 kGy dose was delivered in just 2 s whereas using gamma it took 5.4 h. Differences were also seen when comparing the same samples irradiated at different doses. Some substances were not affected by irradiation, others decreased in concentration and others were formed upon increasing doses of irradiation. These results confirm that irradiation-induced changes do occur in substances with the potential to migrate and that the safety of the finished packaging material following irradiation should be assessed.

  11. The irradiation effects on zirconium alloys

    NASA Astrophysics Data System (ADS)

    Negut, Gh.; Ancuta, M.; Radu, V.; Ionescu, S.; Stefan, V.; Uta, O.; Prisecaru, I.; Danila, N.

    2007-05-01

    Pressure tube samples were irradiated under helium atmosphere in the TRIGA Steady State Research and Material Test Reactor of the Romanian Institute for Nuclear Research (INR). These samples are made of the Zr-2.5%Nb alloy used as structural material for the CANDU Romanian power reactors. After irradiation, mechanical tests were performed in the Post Irradiation Examination Laboratory (PIEL) to study the influence of irradiation on zirconium alloys mechanical behaviour. The tensile test results were used for structural integrity assessment. Results of the tests are presented. The paper presents, also, pressure tube structural integrity assessment.

  12. Study of irradiation creep of vanadium alloys

    SciTech Connect

    Tsai, H.; Strain, R.V.; Smith, D.L.

    1997-08-01

    Thin-wall tubing was produced from the 832665 (500 kg) heat of V-4 wt.% Cr-4 wt.% Ti to study its irradiation creep behavior. The specimens, in the form of pressurized capsules, were irradiated in Advanced Test Reactor and High Flux Isotope Reactor experiments (ATR-A1 and HFIR RB-12J, respectively). The ATR-A1 irradiation has been completed and specimens from it will soon be available for postirradiation examination. The RB-12J irradiation is not yet complete.

  13. Healing burns using atmospheric pressure plasma irradiation

    NASA Astrophysics Data System (ADS)

    Hirata, Takamichi; Kishimoto, Takumi; Tsutsui, Chihiro; Kanai, Takao; Mori, Akira

    2014-01-01

    An experiment testing the effects of plasma irradiation with an atmospheric-pressure plasma (APP) reactor on rats given burns showed no evidence of electric shock injuries upon pathology inspection of the irradiated skin surface. In fact, the observed evidence of healing and improvement of the burns suggested healing effects from plasma irradiation. The quantities of neovascular vessels in the living tissues at 7 days were 9.2 ± 0.77 mm-2 without treatment and 18.4 ± 2.9 mm-2 after plasma irradiation.

  14. A scaling study of the natural circulation flow of the ex-vessel core catcher cooling system of EU-APR1400 for designing a scale-down test facility for design verification

    SciTech Connect

    Rhee, B. W.; Ha, K. S.; Park, R. J.; Song, J. H.; Revankar, S. T.

    2012-07-01

    In this paper a scaling study on the steady state natural circulation flow along the flow path of the ex vessel core catcher cooling system of EU-APR1400 is described, and the scaling criteria for reproducing the same steady state thermalhydraulic characteristics of the natural circulation flow as a prototype core catcher cooling system in the scale-down test facility are derived in terms of the down-comer pipe diameter and orifice resistance. (authors)

  15. Food irradiation: Key research needs

    SciTech Connect

    Morehouse, K.M. )

    1993-01-01

    Treatment of foods with ionizing radiation reduces microbial infection and insect infestations, inhibits sprouting, and delays maturation, thereby extending the shelf life of foods. The treatment of different types of foods with ionizing radiation for specific purposes is accepted in several countries, although it is prohibited in others. The US Food and Drug Administration has established regulations to allow the treatment of several different foods with ionizing radiation and has received petitions for the approval of radiation treatment of additional foods. When carried out according to established good manufacturing practices, food irradiation yields safe, wholesome foods. The irradiated product may be often chemically or microbiologically [open quotes]safer[close quotes] than the nonirradiated product. This paper presents several areas of scientific research in which more information would facilitate the expansion of this technology and points out major areas of concern. The question of the public acceptance of foods that have been treated with ionizing radiation is discussed only briefly in order to make the presentation complete.

  16. A SU-8 dish for cell irradiation

    NASA Astrophysics Data System (ADS)

    Arteaga-Marrero, N.; Auzelyte, V.; Olsson, M. G.; Pallon, J.

    2007-10-01

    The objective of the CELLION project is radiation research at low doses. The main cell responses to low dose irradiation are bystander effects, genomic instability and adaptive responses. In order to study these effects it is convenient to make the cells addressable in space and time through locking the cell position. A new alternative dish has been developed for irradiation procedures at the Lund Nuclear Probe. The versatile dish can be used both to cultivate and to hold the cells during the irradiation procedure. The irradiation dish is made of an epoxy-based photopolymer named SU-8 chosen by its flexibility, non-toxicity and biological compatibility to cell attachment. It has been fabricated using a UV lithographic technique. The irradiation dish forms a 2 × 2 mm 2 grid which contains 400 squares. Each square has 80 μm side and is separated from neighbouring ones by 20 μm wide walls. The location of each square is marked by a row letter and column number patterned outside the grid. The Cell Irradiation Facility at the Lund Nuclear Probe utilizes protons to irradiate living cells. A post-cell detection set up is used to control the applied dose, detecting the number of protons after passing through the targeted cell. The transmission requirement is fulfilled by our new irradiation dish. So far, the dish has been used to perform non-targeted irradiation of Hepatoma cells. The cells attach and grow easily on the SU-8 surface. In addition, the irradiation procedure can be performed routinely and faster since the cells are incubated and irradiated in the same surface.

  17. Correlation of irradiation data using activation fluences and irradiation temperature.

    NASA Technical Reports Server (NTRS)

    Lynch, J. H.

    1972-01-01

    A new method of correlating radiation damage data is tested using actual measured data taken from the open literature. This method, the activation fluence method, was found to be as accurate as other contemporary models with which it was compared. The new method also has several advantages over the other methods. The method employs a new entity, the activation fluence (time-integrated specific activation rate), as the independent variables in a regression model. Temperature at which the irradiation takes place is also a variable. Although the method was tested for a specific type of damage (change in nil-ductility transition temperature for A302-B steel) it has no inherent restrictions and is limited only by the imagination of the user.

  18. Cherry Irradiation Studies. 1984 annual report

    SciTech Connect

    Eakin, D.E.; Hungate, F.P.; Tingey, G.L.; Olsen, K.L.; Fountain, J.B.; Burditt, A.K. Jr.; Moffit, H.R.; Johnson, D.A.; Lunden, J.D.

    1985-04-01

    Fresh cherries, cherry fruit fly larvae, and codling moth larvae were irradiated using the PNL cobalt-60 facility to determine the efficacy of irradiation treatment for insect disinfestation and potential shelf life extension. Irradiation is an effective disinfestation treatment with no significant degradation of fruit at doses well above those required for quarantine treatment. Sufficient codling moth control was achieved at projected doses of less than 25 krad; cherry fruit fly control, at projected doses of less than 15 krad. Dose levels up to 60 krad did not adversely affect cherry quality factors tested. Irradiation above 60 krad reduced the firmness of cherries but had no significant impact on other quality factors tested. Irradiation of cherries below 80 krad did not result in any significant differences in sensory evaluations (appearance, flavor, and firmness) in tests conducted at OSU. Irradiation up to 200 krad at a temperature of about 25/sup 0/C (77/sup 0/F) did not measurably extend shelf life. Irradiation at 500 krad at 25/sup 0/C (77/sup 0/F) increased mold and rotting of cherries tested. There is no apparent advantage of irradiation over low-temperature fumigation.

  19. Reprocessing technology development for irradiated beryllium

    SciTech Connect

    Kawamura, H.; Sakamoto, N.; Tatenuma, K.

    1995-09-01

    At present, beryllium is under consideration as a main candidate material for neutron multiplier and plasma facing material in a fusion reactor. Therefore, it is necessary to develop the beryllium reprocessing technology for effective resource use. And, we have proposed reprocessing technology development on irradiated beryllium used in a fusion reactor. The preliminary reprocessing tests were performed using un-irradiated and irradiated beryllium. At first, we performed beryllium separation tests using un-irradiated beryllium specimens. Un-irradiated beryllium with beryllium oxide which is a main impurity and some other impurities were heat-treated under chlorine gas flow diluted with Ar gas. As the results high purity beryllium chloride was obtained in high yield. And it appeared that beryllium oxide and some other impurities were removed as the unreactive matter, and the other chloride impurities were separated by the difference of sublimation temperature on beryllium chloride. Next, we performed some kinds of beryllium purification tests from beryllium chloride. And, metallic beryllium could be recovered from beryllium chloride by the reduction with dry process. In addition, as the results of separation and purification tests using irradiated beryllium specimens, it appeared that separation efficiency of Co-60 from beryllium was above 96%. It is considered that about 4% Co-60 was carried from irradiated beryllium specimen in the form of cobalt chloride. And removal efficiency of tritium from irradiated beryllium was above 95%.

  20. Proton irradiation study of GFR candidate ceramics

    NASA Astrophysics Data System (ADS)

    Gan, Jian; Yang, Yong; Dickson, Clayton; Allen, Todd

    2009-06-01

    This work investigated the microstructural response of SiC, ZrC and ZrN irradiated with 2.6 MeV protons at 800 °C to a fluence of 2.75 × 10 19 protons/cm 2, corresponding to 0.71-1.8 displacement per atom (dpa), depending on the material. The change of lattice constant evaluated using HOLZ patterns is not observed. In comparison to Kr ion irradiation at 800 °C to 10 dpa from the previous studies, the proton irradiated ZrC and ZrN at 1.8 dpa show less irradiation damage to the lattice structure. The proton irradiated ZrC exhibits faulted loops which are not observed in the Kr ion irradiated sample. ZrN shows the least microstructural change from proton irradiation. The microstructure of 6H-SiC irradiated to 0.71 dpa consists of black dot defects at high density.

  1. A Retailer's Experience with Irradiated Foods

    SciTech Connect

    James P. Corrigan

    2000-11-12

    A food irradiation success story comes from Northbrook, Illinois, where Carrot Top, Inc., has been routinely carrying irradiated food for more than 7 yr. This paper presents the experiences of Carrot Top during those years, details the marketing approaches used, and summarizes the resulting sales figures.

  2. Schedule and status of irradiation experiments

    SciTech Connect

    Rowcliffe, A.F.; Grossbeck, M.L.; Robertson, J.P.

    1998-09-01

    The current status of reactor irradiation experiments is presented in tables summarizing the experimental objectives, conditions, and schedule. Currently, the program has one irradiation experiment in reactor and five experiments in the design or construction stages. Postirradiation examination and testing is in progress on ten experiments.

  3. Electron irradiation of dry food products

    NASA Astrophysics Data System (ADS)

    Grünewald, Th.

    The interest of the industrial food producer is increasing in having the irradiation facility installed in the food processing chain. The throughput of the irradiator should be high and the residence time of the product in the facility should be short. These conditions can be accomplished by electron irradiators. To clarify the irradiation conditions spices taken out of the industrial process, food grade salt, sugar, and gums as models of dry food products were irradiated. With a radiation dose of 10 kGy microbial load can be reduced on 10∗∗4 microorganisms/g. The sensory properties of the spices were not changed in an atypical way. For food grade salt and sugar changes of colour were observed which are due to lattice defects or initiated browning. The irradiation of several gums led only in some cases to an improvement of the thickness properties in the application below 50°C, in most cases the thickness effect was reduced. The products were packaged before irradiation. But it would be possible also to irradiate the products without packaging moving the product through the iradiation field in a closed conveyor system.

  4. Schedule and status of irradiation experiments

    SciTech Connect

    Rowcliffe, A.F.; Grossbeck, M.L.; Robertson, J.P.

    1998-03-01

    The current status of reactor irradiation experiments is presented in tables summarizing the experimental objectives, conditions, and schedule. Currently, the program has four irradiation experiments in reactor, and five experiments in the design or construction stages. Postirradiation examination and testing is in progress on ten experiments.

  5. Electron Spin Relaxation in Irradiated Solids.

    DTIC Science & Technology

    1996-03-01

    the development and use of ELDOR techniques to study the spectral diffusion in irradiated L-alanine and other irradiated organic solids. Pulsed STELDOR...and pulsed two-frequency ELDOR methods were developed and the details of the implementation is reported. The assignment of relaxation times that gave

  6. Immune reactivity after high-dose irradiation

    SciTech Connect

    Gassmann, W.; Wottge, H.U.; von Kolzynski, M.; Mueller-Ruchholtz, W.

    1986-03-01

    Immune reactivity after total-body irradiation was investigated in rats using skin graft rejection as the indicator system. After sublethal irradiation with 10.5 Gy (approximately 50% lethality/6 weeks) the rejection of major histocompatibility complex allogeneic skin grafts was delayed significantly compared with nonirradiated control animals (28 versus 6.5 days). In contrast, skin grafts were rejected after 7.5 days in sublethally irradiated animals and 7 days in lethally irradiated animals if additional skin donor type alloantigens--namely, irradiated bone marrow cells--were given i.v. either simultaneously or with a delay of not more than 24 hr after the above conditioning regimen. These reactions were alloantigen-specific. They were observed in six different strain combinations with varying donors and recipients. Starting on day 2 after irradiation, i.v. injection of bone marrow gradually lost its effectivity and skin grafts were no longer rejected with uniform rapidity; skin donor marrow given on days 4 or 8 did not accelerate skin graft rejection at all. These data show that for approximately 1-2 days after high-dose total-body irradiation rats are still capable of starting a vigorous immune reaction against i.v.-injected alloantigens. The phenomenon of impaired rejection of skin grafted immediately after high-dose irradiation appears to result from the poor accessibility of skin graft alloantigens during the early postirradiation phase when vascularization of the grafted skin is insufficient.

  7. Passive SiC irradiation temperature monitor

    SciTech Connect

    Youngblood, G.E.

    1996-04-01

    A new, improved passive irradiation temperature monitoring method was examined after an irradiation test at 627{degrees}C. The method is based on the analysis of thermal diffusivity changes during postirradiation annealing of polycrystalline SiC. Based on results from this test, several advantages for using this new method rather than a method based on length or lattice parameter changes are given.

  8. Many variable region genes are utilized in the antibody response of BALB/c mice to the influenza virus A/PR/8/34 hemagglutinin.

    PubMed

    Caton, A J; Stark, S E; Kavaler, J; Staudt, L M; Schwartz, D; Gerhard, W

    1991-09-01

    We have examined how many different H chain variable (VH) and kappa-chain variable (Vk) germ-line genes are used in the antibody response to the influenza virus A/PR/8/34 hemagglutinin (PR8 HA), and have assessed how the expression of individual VH and/or Vk genes contributes to the generation of specificity for the HA. A panel of 51 hybridoma antibodies that recognize two antigenic regions on the HA were compared for the sequence of their Ig H and L chain V regions. The hybridomas were obtained from 28 individual BALB/c mice that had been immunized with PR8 under a variety of primary and secondary response immunization protocols. The degree and pattern of sequence similarity suggests that 29 different VH genes drawn from seven different VH gene families, and 25 different Vk genes drawn from 12 different Vk gene families were used in this panel. Based on current estimates of the total numbers of VH and Vk genes in the mouse, this suggests that between 2.5 and 10% of the entire VH and Vk germ-line repertoires were used by these hybridomas. Despite this extensive diversity, some V genes were repetitively identified among these hybridomas, and were most often expressed in the context of specific VH/Vk combinations. Because antibodies that used identical VH/Vk combinations also usually displayed similar reactivity patterns with a panel of mutant viruses, this indicates that VH/Vk pairing can be important in establishing the specificity of antibodies for the HA.

  9. Coadministration of Hedera helix L. Extract Enabled Mice to Overcome Insufficient Protection against Influenza A/PR/8 Virus Infection under Suboptimal Treatment with Oseltamivir.

    PubMed

    Hong, Eun-Hye; Song, Jae-Hyoung; Shim, Aeri; Lee, Bo-Ra; Kwon, Bo-Eun; Song, Hyuk-Hwan; Kim, Yeon-Jeong; Chang, Sun-Young; Jeong, Hyeon Gun; Kim, Jong Geal; Seo, Sang-Uk; Kim, HyunPyo; Kwon, YongSoo; Ko, Hyun-Jeong

    2015-01-01

    Several anti-influenza drugs that reduce disease manifestation exist, and although these drugs provide clinical benefits in infected patients, their efficacy is limited by the emergence of drug-resistant influenza viruses. In the current study, we assessed the therapeutic strategy of enhancing the antiviral efficacy of an existing neuraminidase inhibitor, oseltamivir, by coadministering with the leaf extract from Hedera helix L, commonly known as ivy. Ivy extract has anti-inflammatory, antibacterial, antifungal, and antihelminthic properties. In the present study, we investigated its potential antiviral properties against influenza A/PR/8 (PR8) virus in a mouse model with suboptimal oseltamivir that mimics a poor clinical response to antiviral drug treatment. Suboptimal oseltamivir resulted in insufficient protection against PR8 infection. Oral administration of ivy extract with suboptimal oseltamivir increased the antiviral activity of oseltamivir. Ivy extract and its compounds, particularly hedrasaponin F, significantly reduced the cytopathic effect in PR8-infected A549 cells in the presence of oseltamivir. Compared with oseltamivir treatment alone, coadministration of the fraction of ivy extract that contained the highest proportion of hedrasaponin F with oseltamivir decreased pulmonary inflammation in PR8-infected mice. Inflammatory cytokines and chemokines, including tumor necrosis factor-alpha and chemokine (C-C motif) ligand 2, were reduced by treatment with oseltamivir and the fraction of ivy extract. Analysis of inflammatory cell infiltration in the bronchial alveolar of PR8-infected mice revealed that CD11b+Ly6G+ and CD11b+Ly6Cint cells were recruited after virus infection; coadministration of the ivy extract fraction with oseltamivir reduced infiltration of these inflammatory cells. In a model of suboptimal oseltamivir treatment, coadministration of ivy extract fraction that includes hedrasaponin F increased protection against PR8 infection that could be

  10. Coadministration of Hedera helix L. Extract Enabled Mice to Overcome Insufficient Protection against Influenza A/PR/8 Virus Infection under Suboptimal Treatment with Oseltamivir

    PubMed Central

    Shim, Aeri; Lee, Bo-Ra; Kwon, Bo-Eun; Song, Hyuk-Hwan; Kim, Yeon-Jeong; Chang, Sun-Young; Jeong, Hyeon Gun; Kim, Jong Geal; Seo, Sang-Uk; Kim, HyunPyo; Kwon, YongSoo; Ko, Hyun-Jeong

    2015-01-01

    Several anti-influenza drugs that reduce disease manifestation exist, and although these drugs provide clinical benefits in infected patients, their efficacy is limited by the emergence of drug-resistant influenza viruses. In the current study, we assessed the therapeutic strategy of enhancing the antiviral efficacy of an existing neuraminidase inhibitor, oseltamivir, by coadministering with the leaf extract from Hedera helix L, commonly known as ivy. Ivy extract has anti-inflammatory, antibacterial, antifungal, and antihelminthic properties. In the present study, we investigated its potential antiviral properties against influenza A/PR/8 (PR8) virus in a mouse model with suboptimal oseltamivir that mimics a poor clinical response to antiviral drug treatment. Suboptimal oseltamivir resulted in insufficient protection against PR8 infection. Oral administration of ivy extract with suboptimal oseltamivir increased the antiviral activity of oseltamivir. Ivy extract and its compounds, particularly hedrasaponin F, significantly reduced the cytopathic effect in PR8-infected A549 cells in the presence of oseltamivir. Compared with oseltamivir treatment alone, coadministration of the fraction of ivy extract that contained the highest proportion of hedrasaponin F with oseltamivir decreased pulmonary inflammation in PR8-infected mice. Inflammatory cytokines and chemokines, including tumor necrosis factor-alpha and chemokine (C-C motif) ligand 2, were reduced by treatment with oseltamivir and the fraction of ivy extract. Analysis of inflammatory cell infiltration in the bronchial alveolar of PR8-infected mice revealed that CD11b+Ly6G+ and CD11b+Ly6Cint cells were recruited after virus infection; coadministration of the ivy extract fraction with oseltamivir reduced infiltration of these inflammatory cells. In a model of suboptimal oseltamivir treatment, coadministration of ivy extract fraction that includes hedrasaponin F increased protection against PR8 infection that could be

  11. ECC Water Film Spreading, ECC Water Bypass and Sweep-out Phenomena in the Downcomer with DVI of APR1400 under LBLOCA

    SciTech Connect

    Lee, Dong Won; No, Hee Cheon; Kim, Han Kon; Oh, Seung Jong

    2002-07-01

    In the present study, several experiments related to the thermal-hydraulic phenomena in downcomer with DVI under LBLOCA (Large Break Loss of Coolant Accident) were carried out using the experimental facility of plane-channel type scaled down as 1/7 ratio of prototype reactor (APR1400). Especially, phenomena such as ECC (Emergency Core Cooling) water entrainment and mixing in the downcomer were focused in the present study. Water film spreading was studied and compared with the full-scaled experiment and the experiment with a 1/7 scaled cylindrical-type test section to see the scaling effect and its curvature effect. It turns out that the curvature effect is negligible and the present modified linear scaling law is more appropriate than the linear scaling law. The water height and the amount of ECC water bypass by onset of sweep-out were measured from the visual observation of sweep-out in the downcomer. From this test, the onset of continuous sweep-out was used to analyze the water height in the downcomer. The amount of ECC water bypass by sweep-out was measured and compared with the UCB and KfK correlations. It is found that the best fit of the data from the present experiment lies between the predictions by the two correlations. ECC water mixing phenomena in downcomer were observed focusing on the ECC water film behavior. From the air and water mixing tests, it is concluded that ECC water bypass fraction is highly dependent on DVI position rather than gas flow rates and ECC water bypass fraction is less than 10% of injection ECC water. From the steam and water mixing tests, it is concluded that ECC bypass fraction with steam injection is under 1.5% and much less than that with an air injection because of the condensation in the downcomer. (authors)

  12. Folate, vitamin B12, and vitamin B6 status of a group of high socioeconomic status women in the Alberta Pregnancy Outcomes and Nutrition (APrON) cohort.

    PubMed

    Fayyaz, Faiqa; Wang, Flora; Jacobs, René L; O'Connor, Deborah L; Bell, Rhonda C; Field, Catherine J

    2014-12-01

    Folic acid supplementation and food fortification policies have improved folate status in North American women of child bearing age. Recent studies have reported the possible inadequacy of vitamin B12 and B6 in the etiology of neural tube defects in folate-fortified populations. The aims of this study were to describe folate status and its relationship to supplementation and to assess vitamin B12 and B6 status in a cohort of pregnant women. Supplement intake data were collected in each trimester from the first cohort (n = 599) of the Alberta Pregnancy Outcomes and Nutrition (APrON) study. Red blood cell folate (RBCF) and plasma folate, holotranscobalamin, and pyridoxal 5-phosphate were measured. Overt folate deficiency was rare (3%) but 24% of women in their first trimester had suboptimal RBCF concentration (<906 nmol·L(-1)). The proportion of the cohort in this category declined substantially in second (9%) and third (7%) trimesters. High RBCF (>1360 nmol·L(-1)) was observed in approximately half of the women during each pregnancy trimester. Vitamin B12 and B6 deficiencies were rare (<1% of the cohort). Women consuming folic acid supplements above the upper level had significantly higher RBCF and plasma folate concentrations. In conclusion, the prevalence of vitamin B12 and B6 deficiency was very low. A quarter of the women had suboptimal folate status in the first trimester of pregnancy and over half the women had abnormally high RBCF, suggesting that supplementation during pregnancy is not appropriate in a cohort of women considered to be healthy and a low risk for nutritional deficiencies.

  13. AGR-1 Post Irradiation Examination Final Report

    SciTech Connect

    Demkowicz, Paul Andrew

    2015-08-01

    The post-irradiation examination (PIE) of the Advanced Gas Reactor (AGR)-1 experiment was a multi-year, collaborative effort between Idaho National Laboratory (INL) and Oak Ridge National Laboratory (ORNL) to study the performance of UCO (uranium carbide, uranium oxide) tristructural isotropic (TRISO) coated particle fuel fabricated in the U.S. and irradiated at the Advanced Test Reactor at INL to a peak burnup of 19.6% fissions per initial metal atom. This work involved a broad array of experiments and analyses to evaluate the level of fission product retention by the fuel particles and compacts (both during irradiation and during post-irradiation heating tests to simulate reactor accident conditions), investigate the kernel and coating layer morphology evolution and the causes of coating failure, and explore the migration of fission products through the coating layers. The results have generally confirmed the excellent performance of the AGR-1 fuel, first indicated during the irradiation by the observation of zero TRISO coated particle failures out of 298,000 particles in the experiment. Overall release of fission products was determined by PIE to have been relatively low during the irradiation. A significant finding was the extremely low levels of cesium released through intact coatings. This was true both during the irradiation and during post-irradiation heating tests to temperatures as high as 1800°C. Post-irradiation safety test fuel performance was generally excellent. Silver release from the particles and compacts during irradiation was often very high. Extensive microanalysis of fuel particles was performed after irradiation and after high-temperature safety testing. The results of particle microanalysis indicate that the UCO fuel is effective at controlling the oxygen partial pressure within the particle and limiting kernel migration. Post-irradiation examination has provided the final body of data that speaks to the quality of the AGR-1 fuel, building

  14. Production of modified starches by gamma irradiation

    NASA Astrophysics Data System (ADS)

    Kang, Il-Jun; Byun, Myung-Woo; Yook, Hong-Sun; Bae, Chun-Ho; Lee, Hyun-Soo; Kwon, Joong-Ho; Chung, Cha-Kwon

    1999-04-01

    As a new processing method for the production of modified starch, gamma irradiation and four kinds of inorganic peroxides were applied to commercial corn starch. The addition of inorganic peroxides without gamma irradiation or gamma irradiation without the addition of inorganic peroxides effectively decreased initial viscosity, but did not sufficiently keep viscosity stable. The combination of adding ammonium persulfate (APS) and gamma irradiation showed the lowest initial viscosity and the best stability out of the tested four kinds of inorganic peroxides. Among the tested mixing methods of APS, soaking was found to be more effective than dry blending or spraying. Therefore, the production of modified starch with low viscosity as well as with sufficient viscosity stability became feasible by the control of gamma irradiation dose levels and the amount of added APS to starch.

  15. Characterisation and disintegration properties of irradiated starch.

    PubMed

    De Kerf, M; Mondelaers, W; Lahorte, P; Vervaet, C; Remon, J P

    2001-06-19

    Irradiation treatment could provide a quick and simple way to modify the physical, chemical and pharmaceutical properties of biopolymers such as starch. Corn, potato and drum dried corn starch were exposed to X-ray and electron beam (e-beam) irradiation treatment at doses of 10, 50 and 100 kGy. The disintegration properties of these starches were compared using alpha-lactose monohydrate tablets containing 5% (w/w) starch as disintegrant. Starch solubility increased, while its swelling capacity decreased with increasing irradiation dose. The irradiation treatment caused fragmentation of the amylopectin fraction. Irradiation modified the different starches thoroughly, showing remarkable differences in disintegration properties after X-ray treatment and e-beam modification. The e-beam modification resulted in significantly higher disintegration times of the tablets.

  16. Effect of Laser Irradiation on Enzyme Activity

    NASA Astrophysics Data System (ADS)

    Murakami, Satoshi; Kashii, Masafumi; Kitano, Hiroshi; Adachi, Hiroaki; Takano, Kazufumi; Matsumura, Hiroyoshi; Inoue, Tsuyoshi; Mori, Yusuke; Doi, Masaaki; Sugamoto, Kazuomi; Yoshikawa, Hideki; Sasaki, Takatomo

    2005-11-01

    We previously developed a protein crystallization technique using a femtosecond laser and protein crystal processing and detaching techniques using a pulsed UV laser. In this study, we examine the effect of laser irradiation on protein integrity. After several kinds of laser were irradiated on part of a solution of glycerol-6-phosphate dehydrogenase from Leuconostoc mesenteroides, we measured the enzyme activity. Femtosecond and deep-UV laser irradiations have little influence on the whole enzyme activity, whereas the enzyme lost its activity upon high-power near-infrared laser irradiation at a wavelength of 1547 nm. These results suggest that suitable laser irradiation has no remarkable destructive influence on protein crystallization or crystal processing.

  17. Cost effective alternative to low irradiance measurements

    NASA Technical Reports Server (NTRS)

    Oleary, Scott T.

    1988-01-01

    Martin Marietta's Space Simulation Laboratory (SSL) has a Thermal Environment Simulator (TES) with 56 individually controlled heater zones. The TES has a temperature range of approximately minus 129 C to plus 149 C. Because of the ability of TES to provide complex irradiance distributions, it is necessary to be able to measure a wide range of irradiance levels. SSL currently uses ambient temperature controlled radiometers with the capacity to measure sink irradiance levels of approximately 42.6 mw/sq cm, sink temperature equals 21 C and up. These radiometers could not be used to accurately measure the lower irradiance levels of the TES. Therefore, it was necessary to obtain a radiometer or develop techniques which could be used to measure lower irradiance levels.

  18. ATF Neutron Irradiation Program Technical Plan

    SciTech Connect

    Geringer, J. W.; Katoh, Yutai

    2016-03-01

    The Japan Atomic Energy Agency (JAEA) under the Civil Nuclear Energy Working Group (CNWG) is engaged in a cooperative research effort with the U.S. Department of Energy (DOE) to explore issues related to nuclear energy, including research on accident-tolerant fuels and materials for use in light water reactors. This work develops a draft technical plan for a neutron irradiation program on the candidate accident-tolerant fuel cladding materials and elements using the High Flux Isotope Reactor (HFIR). The research program requires the design of a detailed experiment, development of test vehicles, irradiation of test specimens, possible post-irradiation examination and characterization of irradiated materials and the shipment of irradiated materials to JAEA in Japan. This report discusses the technical plan of the experimental study.

  19. Relief of vasospasm by intravascular ultraviolet irradiation

    NASA Astrophysics Data System (ADS)

    Nakai, Kanji; Morimoto, Yuji; Ito, Hirotaka; Kominami, Kimito; Matsuo, Hirotaka; Arai, Tsunenori; Kikuchi, Makoto

    1998-05-01

    We investigated the photovasorelaxation with intravascular transluminal irradiation using in vivo model. A 2.5 Fr. catheter was inserted in the femoral artery of a rabbit under anesthesia. A 400 micrometers diameter quartz fiber was inserted through the catheter. The catheter was withdrawn from the distal end to the proximal end of the exposed femoral artery without laser irradiation in order to observe the mechanical dilation by the procedure. The femoral artery lumen was irradiated by a Helium-Cadmium(He-Cd) laser (wavelength; 325 nm) with 8 mW through the fiber during 30 s. We carried out that the laser irradiation produced vasorelaxation (185% on the average) compared with mechanical vasodilation (150% on the average) with angiography. The results suggest that intravascular transluminal irradiation with low-power UV laser might be applicable to the relief of acute arterial vasospasm.

  20. Modeling of Irradiation Hardening of Polycrystalline Materials

    SciTech Connect

    Li, Dongsheng; Zbib, Hussein M.; Garmestani, Hamid; Sun, Xin; Khaleel, Mohammad A.

    2011-09-14

    High energy particle irradiation of structural polycrystalline materials usually produces irradiation hardening and embrittlement. The development of predict capability for the influence of irradiation on mechanical behavior is very important in materials design for next generation reactors. In this work a multiscale approach was implemented to predict irradiation hardening of body centered cubic (bcc) alpha-iron. The effect of defect density, texture and grain boundary was investigated. In the microscale, dislocation dynamics models were used to predict the critical resolved shear stress from the evolution of local dislocation and defects. In the macroscale, a viscoplastic self-consistent model was applied to predict the irradiation hardening in samples with changes in texture and grain boundary. This multiscale modeling can guide performance evaluation of structural materials used in next generation nuclear reactors.

  1. Li + grafting of ion irradiated polyethylene

    NASA Astrophysics Data System (ADS)

    Švorčík, V.; Rybka, V.; Vacík, J.; Hnatowicz, V.; Öchsner, R.; Ryssel, H.

    1999-02-01

    Foils of oriented polyethylene (PE) were irradiated with 63 keV Ar + and 155 keV Xe + ions to different fluences at room temperature and then doped from water solution of LiCl. The as irradiated and irradiated plus doped samples were examined by IR, EPR and neutron depth profiling (NDP) technique. The sheet resistance was also measured by the standard two points method. After Li salt doping of ion modified layer of PE, a reaction between degraded macromolecules and Li occur and thus a new chemical structure C-Li + is formed. Owing to the presence of these cations on the polymer chain, the irradiated plus doped layer exhibits higher electric conductivity compared to as-irradiated ones.

  2. Microbiological decontamination of natural honey by irradiation

    NASA Astrophysics Data System (ADS)

    Migdał, W.; Owczarczyk, H. B.; K ȩdzia, B.; Hołderna-K ȩdzia, E.; Madajczyk, D.

    2000-03-01

    Degree of microbiological decontamination, organoleptic and physico-chemical properties of natural honeys were investigated after radiation treatment. Seven kinds of honeys were irradiated with the beams of 10 MeV electrons from a 10 kW linear accelerator "Elektronika 10-10" at the dose 10 kGy. It was shown, that after irradiation, the total count of aerobic and anaerobic bacteria and moulds decrease by 99%. The antibiotic value in investigated honeys increased in turn from 1.67 to 2.67 after irradiation. Such factors and parameters of investigated honeys as their consistency, content of water and saccharose, acidity, the diastase and 5-HMF values were not changed significantly after irradiation. Decontamination by irradiation is a process which allows us to obtain high microbiological purity of honeys. It is especially needed, when honeys are used in surgical treatment of injuries and in nutrition of babies with food deficiency.

  3. ESR spectroscopic properties of irradiated gum Arabic.

    PubMed

    Leonor, S J; Gómez, J A; Kinoshita, A; Calandreli, I; Tfouni, E; Baffa, O

    2013-12-01

    Electron spin resonance (ESR) spectra of irradiated gum Arabic with doses between 0.5 and 5 kGy were studied. A linear relationship between the absorbed dose and the intensities of the ESR spectra was observed. ESR spectra of irradiated gum Arabic showed a decay of relative concentrations of free radicals originated by radiation and the production of at least two species of free radicals with half-times: 3.3 and 125.4 h. The results of spectral simulations for these radical groups were giso=2.0046; A=1.2 mT and gx=gy=2.0062, gz=2.0025. Hydration and dehydration of irradiated gum Arabic returns the ESR spectrum to its initial state before irradiation. The results show that ESR can be used as simple and reliable method to detect irradiated gum Arabic up to 60 days after initial radiation with doses on the order of 5 kGy.

  4. Tensile properties of irradiated surveillance coupons

    SciTech Connect

    Huang, F.H.; Blackburn, L.D.

    1994-06-01

    Tensile testing of austenitic steel and superalloy samples irradiated in the HMO 13 assembly was performed in support of the Fast Flux Test Facility (FFTF) Surveillance Program. Postirradiation yield stress, ultimate tensile stress, uniform elongation, total elongation, and reduction in area of 304 stainless steel (SS), 308 SS weld, 316 SS, A286, In718, and In718 weld were determined. Results showed the strength of austenitic steels increased while the ductility decreased as a result of irradiation. Low irradiation exposure produced little property change in In718. Overall, the tensile properties of HMO 13 surveillance coupons showed a lower magnitude of irradiation-induced property change than was expected based on earlier studies. Results from these tests gave no indications of unexpectedly severe irradiation damage to FFTF components.

  5. RERTR-7 Irradiation Summary Report

    SciTech Connect

    D. M. Perez; M. A. Lillo; G. S. Chang; G. A. Roth; N. E. Woolstenhulme; D. M. Wachs

    2011-12-01

    The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-7A, was designed to test several modified fuel designs to target fission densities representative of a peak low enriched uranium (LEU) burnup in excess of 90% U-235 at peak experiment power sufficient to generate a peak surface heat flux of approximately 300 W/cm2. The RERTR-7B experiment was designed as a high power test of 'second generation' dispersion fuels at peak experiment power sufficient to generate a surface heat flux on the order of 230 W/cm2.1 The following report summarizes the life of the RERTR-7A and RERTR-7B experiments through end of irradiation, including as-run neutronic analyses, thermal analyses and hydraulic testing results.

  6. Variability of solar ultraviolet irradiance

    NASA Technical Reports Server (NTRS)

    Pap, J. M.; Donnelly, R. F.; Hudson, H. S.; Rottman, G. J.; Willson, R. C.

    1991-01-01

    A model of solar Lyman alpha irradiance developed by multiple linear regression analysis, including the daily values and 81-day running means of the full disk equivalent width of the Helium line at 1083 nm, predicts reasonably well both the short- and long-term variations observed in Lyman alpha. In contrast, Lyman alpha models calculated from the 10.7-cm radio flux overestimate the observed variations in the rising portion and maximum period of solar cycle, and underestimates them during solar minimum. Models are shown of Lyman alpha based on the He-line equivalent width and 10.7-cm radio flux for those time intervals when no satellite observations exist, namely back to 1974 and after April 1989, when the measurements of the Solar Mesosphere Satellite were terminated.

  7. AFIP-3 Irradiation Summary Report

    SciTech Connect

    Danielle M Perez; M. A. Lillo; G. S. Chang; G. A. Roth; N. E. Woolstenhulme; D. M. Wachs

    2011-05-01

    The Advanced Test Reactor (ATR) Full size plate In center flux trap Position (AFIP) experiment AFIP-3 was designed to evaluate the performance of monolithic fuels at a prototypic scale of 2.25 inches x 21.5 inches x 0.050 inches (5.75 cm x 54.6 cm x 0.13cm). The AFIP-3 experiment was fabricated by hot isostatic pressing (HIP) and consists of two plates, one with a zirconium (Zr) diffusion barrier and one with a silicon (Si) enhanced fuel/clad interface1,2. The following report summarizes the life of the AFIP-3 experiment through end of irradiation, including a brief description of the safety analysis, as-run neutronic analysis results, hydraulic testing results, and thermal analysis results.

  8. AFIP-3 Irradiation Summary Report

    SciTech Connect

    Danielle M Perez

    2011-04-01

    The Advanced Test Reactor (ATR) Full size plate In center flux trap Position (AFIP) experiment AFIP-3 was designed to evaluate the performance of monolithic fuels at a prototypic scale of 2.25 inches x 21.5 inches x 0.050 inches (5.75 cm x 54.6 cm x 0.13cm). The AFIP-3 experiment was fabricated by hot isostatic pressing (HIP) and consists of two plates, one with a zirconium (Zr) diffusion barrier and one with a silicon (Si) enhanced fuel/clad interface1,2. The following report summarizes the life of the AFIP-3 experiment through end of irradiation, including a brief description of the safety analysis, as-run neutronic analysis results, hydraulic testing results, and thermal analysis results.

  9. AFIP-3 Irradiation Summary Report

    SciTech Connect

    Danielle M Perez; M. A. Lillo; G. S. Chang; G. A. Roth; N. E. Woolstenhulme; D. M. Wachs

    2012-03-01

    The Advanced Test Reactor (ATR) Full size plate In center flux trap Position (AFIP) experiment AFIP-3 was designed to evaluate the performance of monolithic fuels at a prototypic scale of 2.25 inches x 21.5 inches x 0.050 inches (5.75 cm x 54.6 cm x 0.13cm). The AFIP-3 experiment was fabricated by hot isostatic pressing (HIP) and consists of two plates, one with a zirconium (Zr) diffusion barrier and one with a silicon (Si) enhanced fuel/clad interface1,2. The following report summarizes the life of the AFIP-3 experiment through end of irradiation, including a brief description of the safety analysis, as-run neutronic analysis results, hydraulic testing results, and thermal analysis results.

  10. RERTR-10 Irradiation Summary Report

    SciTech Connect

    D. M. Perez

    2011-05-01

    The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-10 was designed to further test the effectiveness of modified fuel/clad interfaces in monolithic fuel plates. The experiment was conducted in two campaigns: RERTR-10A and RERTR-10B. The fuel plates tested in RERTR-10A were all fabricated by Hot Isostatic Pressing (HIP) and were designed to evaluate the effect of various Si levels in the interlayer and the thickness of the Zr interlayer (0.001”) using 0.010” and 0.020” nominal foil thicknesses. The fuel plates in RERTR-10B were fabricated by Friction Bonding (FB) with two different thickness Si layers and Nb and Zr diffusion barriers.1 The following report summarizes the life of the RERTR-10A/B experiment through end of irradiation, including as-run neutronic analysis results, thermal analysis results and hydraulic testing results.

  11. Irradiation creep of dispersion strengthened copper alloy

    SciTech Connect

    Pokrovsky, A.S.; Barabash, V.R.; Fabritsiev, S.A.

    1997-04-01

    Dispersion strengthened copper alloys are under consideration as reference materials for the ITER plasma facing components. Irradiation creep is one of the parameters which must be assessed because of its importance for the lifetime prediction of these components. In this study the irradiation creep of a dispersion strengthened copper (DS) alloy has been investigated. The alloy selected for evaluation, MAGT-0.2, which contains 0.2 wt.% Al{sub 2}O{sub 3}, is very similar to the GlidCop{trademark} alloy referred to as Al20. Irradiation creep was investigated using HE pressurized tubes. The tubes were machined from rod stock, then stainless steel caps were brazed onto the end of each tube. The creep specimens were pressurized by use of ultra-pure He and the stainless steel caps subsequently sealed by laser welding. These specimens were irradiated in reactor water in the core position of the SM-2 reactors to a fluence level of 4.5-7.1 x 10{sup 21} n/cm{sup 2} (E>0.1 MeV), which corresponds to {approx}3-5 dpa. The irradiation temperature ranged from 60-90{degrees}C, which yielded calculated hoop stresses from 39-117 MPa. A mechanical micrometer system was used to measure the outer diameter of the specimens before and after irradiation, with an accuracy of {+-}0.001 mm. The irradiation creep was calculated based on the change in the diameter. Comparison of pre- and post-irradiation diameter measurements indicates that irradiation induced creep is indeed observed in this alloy at low temperatures, with a creep rate as high as {approx}2 x 10{sup {minus}9}s{sup {minus}1}. These results are compared with available data for irradiation creep for stainless steels, pure copper, and for thermal creep of copper alloys.

  12. Historical Variations in Solar UV Irradiance

    NASA Astrophysics Data System (ADS)

    DeLand, M. T.

    2011-12-01

    Satellite measurements of solar UV variability have been made by at least fifteen different instruments since 1978. While it is difficult to keep a single UV irradiance instrument operating throughout a complete solar cycle, many of these instruments (Nimbus-7 SBUV, SME, NOAA-9 SBUV/2, NOAA-11 SBUV/2, UARS SUSIM, UARS SOLSTICE) were able to observe both maximum and minimum irradiance levels during either rising or declining phases of solar activity. Comparisons of these published results for solar cycles 21, 22, and 23 show consistent solar cycle irradiance changes at key wavelengths for terrestrial effects (e.g. 205 nm, 240 nm) within instrumental uncertainties. All historical data sets also show the same relative spectral dependence in the ultraviolet for both short-term (rotational) and long-term (solar cycle) variations. Empirical solar irradiance models that employ multiple proxy data sets to represent spectral irradiance produce long-term solar UV variations that are in good agreement with merged observational data through 2005. Recent UV irradiance data from the SORCE mission covering the declining phase of Cycle 23 present a different picture of long-term solar variations, with significantly larger temporal changes and different spectral dependence. We present comparisons of the SORCE irradiance data with previous solar UV observations and current model predictions. Scaling factors for use with solar UV proxy indexes have been derived from SORCE SIM and SORCE SOLSTICE data during 2004-2005. These scale factors, based on short-term irradiance variations, agree very well with results derived from concurrent NOAA-17 SBUV/2 and UARS SUSIM measurements. The 2004-2005 scale factors are consistent with previously derived scale factors that produce calculated long-term irradiance changes in good agreement with observations. The SORCE long-term solar UV irradiance results, corresponding to the early part of the mission, are consistent with undercorrection of

  13. Parameterization of Solar Global Uv Irradiation

    NASA Astrophysics Data System (ADS)

    Feister, U.; Jaekel, E.; Gericke, K.

    Daily doses of solar global UV-B, UV-A, and erythemal irradiation have been param- eterized to be calculated from pyranometer data of global and diffuse irradiation as well as from atmospheric column ozone measured at Potsdam (52 N, 107 m asl). The method has been validated against independent data of measured UV irradiation. A gain of information is provided by use of the parameterization for the three UV compo- nents (UV-B, UV-A and erythemal) referring to average values of UV irradiation. Ap- plying the method to UV irradiation measured at the mountain site Hohenpeissenberg (48 N, 977 m asl) shows that the parameterization even holds under completely differ- ent climatic conditions. On a long-term average (1953 - 2000), parameterized annual UV irradiation values are by 15 % (UV-A) and 21 % (UV-B), respectively, higher at Hohenpeissenberg, than they are at Potsdam. Using measured input data from 27 Ger- man weather stations, the method has been also applied to estimate the spatial distribu- tion of UV irradiation across Germany. Daily global and diffuse irradiation measured at Potsdam (1937 -2000) as well as atmospheric column ozone measured at Potsdam between1964 - 2000 have been used to derive long-term estimates of daily and annual totals of UV irradiation that include the effects of changes in cloudiness, in aerosols and, at least for the period 1964 to 2000, also in atmospheric ozone. It is shown that the extremely low ozone values observed mainly after the volcanic eruptions of Mt. Pinatubo in 1991 have substantially enhanced UV-B irradiation in the first half of the 90ies of the last century. The non-linear long-term changes between 1968 and 2000 amount to +4% ...+5% for annual global and UV-A irradiation mainly due to changing cloudiness, and +14% ... +15% for UV-B and erythemal irradiation due to both chang- ing cloudiness and decreasing column ozone. Estimates of long-term changes in UV irradiation derived from data measured at other German sites are

  14. AGR-1 Irradiation Experiment Test Plan

    SciTech Connect

    John T. Maki

    2009-10-01

    This document presents the current state of planning for the AGR-1 irradiation experiment, the first of eight planned irradiations for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. The objectives of the AGR-1 experiment are: 1. To gain experience with multi-capsule test train design, fabrication, and operation with the intent to reduce the probability of capsule or test train failure in subsequent irradiation tests. 2. To irradiate fuel produced in conjunction with the AGR fuel process development effort. 3. To provide data that will support the development of an understanding of the relationship between fuel fabrication processes, fuel product properties, and irradiation performance. In order to achieve the test objectives, the AGR-1 experiment will be irradiated in the B-10 position of the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). The test will contain six independently controlled and monitored capsules. Each capsule will contain a single type, or variant, of the AGR coated fuel. The irradiation is planned for about 700 effective full power days (approximately 2.4 calendar years) with a time-averaged, volume-average temperature of approximately 1050 °C. Average fuel burnup, for the entire test, will be greater than 17.7 % FIMA, and the fuel will experience fast neutron fluences between 2.4 and 4.5 x 1025 n/m2 (E>0.18 MeV).

  15. [Near infrared light irradiator using halogen lamp].

    PubMed

    Ide, Yasuo

    2012-07-01

    The practical electric light bulb was invented by Thomas Alva Edison in 1879. Halogen lamp is the toughest and brightest electric light bulb. With light filter, it is used as a source of near infrared light. Super Lizer and Alphabeam are made as near infrared light irradiator using halogen lamp. The light emmited by Super Lizer is linear polarized near infrared light. The wave length is from 600 to 1,600 nm and strongest at about 1,000 nm. Concerning Super Lizer, there is evidence of analgesic effects and normalization of the sympathetic nervous system. Super Lizer has four types of probes. SG type is used for stellate ganglion irradiation. B type is used for narrow area irradiation. C and D types are for broad area irradiation. The output of Alphabeam is not polarized. The wave length is from 700 to 1,600 nm and the strongest length is about 1,000nm. Standard attachment is used for spot irradiation. Small attachment is used for stellate ganglion irradiation. Wide attachment is used for broad area irradiation. The effects of Alphabeam are thought to be similar to that of Super Lizer.

  16. AGC-1 Post Irradiation Examination Status

    SciTech Connect

    David Swank

    2011-09-01

    The Next Generation Nuclear Plant (NGNP) Graphite R&D program is currently measuring irradiated material property changes in several grades of nuclear graphite for predicting their behavior and operating performance within the core of new Very High Temperature Reactor (VHTR) designs. The Advanced Graphite Creep (AGC) experiment consisting of six irradiation capsules will generate this irradiated graphite performance data for NGNP reactor operating conditions. All six AGC capsules in the experiment will be irradiated in the Advanced Test Reactor (ATR), disassembled in the Hot Fuel Examination Facility (HFEF), and examined at the INL Research Center (IRC) or Oak Ridge National Laboratory (ORNL). This is the first in a series of status reports on the progress of the AGC experiment. As the first capsule, AGC1 was irradiated from September 2009 to January 2011 to a maximum dose level of 6-7 dpa. The capsule was removed from ATR and transferred to the HFEF in April 2011 where the capsule was disassembled and test specimens extracted from the capsules. The first irradiated samples from AGC1 were shipped to the IRC in July 2011and initial post irradiation examination (PIE) activities were begun on the first 37 samples received. PIE activities continue for the remainder of the AGC1 specimen as they are received at the IRC.

  17. The Next Spaceflight Solar Irradiance Sensor: TSIS

    NASA Astrophysics Data System (ADS)

    Kopp, Greg; Pilewskie, Peter; Richard, Erik

    2016-05-01

    The Total and Spectral Solar Irradiance Sensor (TSIS) will continue measurements of the solar irradiance with improved accuracies and stabilities over extant spaceflight instruments. The two TSIS solar-observing instruments include the Total Irradiance Monitor (TIM) and the Spectral Irradiance Monitor (SIM) for measuring total- and spectral- solar-irradiance, respectively. The former provides the net energy powering the Earth’s climate system while the latter helps attribute where that energy is absorbed by the Earth’s atmosphere and surface. Both spaceflight instruments are assembled and being prepared for integration on the International Space Station. With operations commencing in late 2017, the TSIS is intended to overlap with NASA’s ongoing SOlar Radiation and Climate Experiment (SORCE) mission, which launched in 2003 and contains the first versions of both the TIM and SIM instruments, as well as with the TSI Calibration Transfer Experiment (TCTE), which began total solar irradiance measurements in 2013. We summarize the TSIS’s instrument improvements and intended solar-irradiance measurements.

  18. Irradiation exposure modulates central opioid functions

    SciTech Connect

    Dougherty, P.M.; Dafny, N.

    1987-11-01

    Exposure to low doses of gamma irradiation results in the modification of both the antinociceptive properties of morphine and the severity of naloxone-precipitated withdrawal in morphine-dependent rats. To better define the interactions between gamma irradiation and these opiate-mediated phenomena, dose-response studies were undertaken of the effect of irradiation on morphine-induced antinociception, and on the naloxone-precipitated withdrawal syndrome of morphine-dependent rats. In addition, electrophysiologic studies were conducted in rats after irradiation exposure and morphine treatment correlating with the behavioral studies. The observations obtained demonstrated that the antinociceptive effects of morphine as well as naloxone-precipitated withdrawal were modified in a dose-dependent manner by irradiation exposure. In addition, irradiation-induced changes in the evoked responses obtained from four different brain regions demonstrated transient alterations in both baseline and morphine-treated responses that may reflect the alterations observed in the behavioral paradigms. These results suggest that the effects of irradiation on opiate activities resulted from physiologic alterations of central endogenous opioid systems due to alterations manifested within peripheral targets.

  19. Rheological changes in irradiated chicken eggs

    NASA Astrophysics Data System (ADS)

    Ferreira, Lúcia F. S.; Del Mastro, Nélida L.

    1998-06-01

    Pathogenic bacteria may cause foodborne illnesses. Humans may introduce pathogens into foods during production, processing, distribution and or preparation. Some of these microorganisms are able to survive conventional preservation treatments. Heat pasteurization, which is a well established and satisfactory means of decontamination/disinfection of liquid foods, cannot efficiently achieve a similar objective for solid foods. Extensive work carried out worldwide has shown that irradiation is efficient in eradicating foodborne pathogens like Salmonella spp. that can contaminate poultry products. In this work Co-60 gamma irradiation was applied to samples of industrial powder white, yolk and whole egg at doses between 0 and 25 kGy. Samples were rehydrated and the viscosity measured in a Brookfield viscosimeter, model DV III at 5, 15 and 25°C. The rheological behaviour among the various kinds of samples were markedly different. Irradiation with doses up to 5 kGy, known to reduced bacterial contamination to non-detectable levels, showed almost no variation of viscosity of irradiated egg white samples. On the other hand, whole or yolk egg samples showed some changes in rheological properties depending on the dose level, showing the predominance of whether polimerization or degradation as a result of the irradiation. Additionally, irradiation of yolk egg powder reduced yolk color as a function of the irradiation exposure implemented. The importance of these results are discussed in terms of possible industrial applications.

  20. Influence of microwave irradiation on enzyme kinetics

    NASA Astrophysics Data System (ADS)

    Pavelkić, V. M.; Stanisavljev, D. R.; Gopčević, K. R.; Beljanski, M. V.

    2009-09-01

    The in vitro effect of 2.45 GHz microwave irradiation on porcine pepsin activity under controlled temperature and absorbed microwave power via kinetic parameters was evaluated. Kinetic study with respect of time of irradiation demonstrated the existence of an inactivation effect of microwaves at pH 2 on pepsin molecule. Bovine serum albumin (BSA)-bromphenol blue (BPB) complex was used as substrate for the assay of pepsin by kinetic method. Depending on absorbed microwave dose, the degree of caused inactivation varies from 39.11 to 45.91% for 5 and 20 min of pepsin MW irradiation, respectively. The V maxapp and K mapp were calculated for low (5 min of MW irradiation) and higher specific absorbed dose (20 min of MW irradiation), as well as for untreated enzyme, from double reciprocal Lineweaver-Burk plot. The effect of microwaves on substrate (BSA-BPB complex) was also investigated. For reaction performed with MW irradiated substrate for 5 min the reaction rate was decreased for 15.15%, while for 20 min of substrate irradiation reaction rate was decreased for 25.52% compared to the control reaction.

  1. Rapid detection of irradiated frozen hamburgers

    NASA Astrophysics Data System (ADS)

    Delincée, Henry

    2002-03-01

    DNA comet assay can be employed as a rapid and inexpensive screening test to check whether frozen ground beef patties (hamburgers) have been irradiated as a means to increase their safety by eliminating pathogenic bacteria, e.g. E. coli O157:H7. Such a detection procedure will provide an additional check on compliance with existing regulations, e.g. enforcement of labelling and rules in international trade. Frozen ready prepared hamburgers from the market place were `electron irradiated' with doses of 0, 1.3, 2.7, 4.5 and 7.2kGy covering the range of potential commercial irradiation. DNA fragmentation in the hamburgers was made visible within a few hours using the comet assay, and non-irradiated hamburgers could be easily discerned from the irradiated ones. Even after 9 months of frozen storage, irradiated hamburgers could be identified. Since DNA fragmentation may also occur with other food processes (e.g. temperature abuse), positive screening tests shall be confirmed using a validated method to specifically prove an irradiation treatment, e.g. EN 1784 or EN 1785.

  2. Microstructure evolution during helium irradiation and post-irradiation annealing in a nanostructured reduced activation steel

    NASA Astrophysics Data System (ADS)

    Liu, W. B.; Ji, Y. Z.; Tan, P. K.; Zhang, C.; He, C. H.; Yang, Z. G.

    2016-10-01

    Severe plastic deformation, intense single-beam He-ion irradiation and post-irradiation annealing were performed on a nanostructured reduced activation ferritic/martensitic (RAFM) steel to investigate the effect of grain boundaries (GBs) on its microstructure evolution during these processes. A surface layer with a depth-dependent nanocrystalline (NC) microstructure was prepared in the RAFM steel using surface mechanical attrition treatment (SMAT). Microstructure evolution after helium (He) irradiation (24.8 dpa) at room temperature and after post-irradiation annealing was investigated using Transmission Electron Microscopy (TEM). Experimental observation shows that GBs play an important role during both the irradiation and the post-irradiation annealing process. He bubbles are preferentially trapped at GBs/interfaces during irradiation and cavities with large sizes are also preferentially trapped at GBs/interfaces during post-irradiation annealing, but void denuded zones (VDZs) near GBs could not be unambiguously observed. Compared with cavities at GBs and within larger grains, cavities with smaller size and higher density are found in smaller grains. The average size of cavities increases rapidly with the increase of time during post-irradiation annealing at 823 K. Cavities with a large size are observed just after annealing for 5 min, although many of the cavities with small sizes also exist after annealing for 240 min. The potential mechanism of cavity growth behavior during post-irradiation annealing is also discussed.

  3. Influences of Microwave Irradiation on Environment

    NASA Astrophysics Data System (ADS)

    Murakami, H.; Abe, Y.; Iwata, T.; Kudo, I.; Saito, K.; Okuda, T.

    2004-12-01

    An experimental facility to evaluate the long-duration influence of microwave to environment, a so-called long duration microwave exposure facility (LDMEF), was constructed in Tsukuba in 1994, and so far irradiation tests on plants accumulated over 40,000 hours have been conducted with the aid of 2.45 GHz magnetron. The LDMEF consists of a pair of outdoor electromagnetically isolated areas, one under the influence of microwave irradiation with a 500 W magnetron and one without microwave irradiation. The growth rates of plants in both areas were compared and evaluated with the experimental data for the temperature distribution in the soil and power distribution of microwave. Although any appreciable influence of microwave was not noticed in the power density less than 10 mW/cm2 , the experimental results showed a significant growth rate enhancement when the power density became over 10 mW/cm2 . However, the growth was rather depressed when the power density increased over 15 mW/cm2 . These effects are well explained by the temperature and moisture in the soil which are also under an appreciable influence of microwave irradiation [1,2]. In this context, we newly constructed an indoor irradiation facility, in which the growth conditions of plants under a constant soil temperature can be maintained. In addition, irradiation with a 5.8 GHz magnetron will be conducted in the new facility. In parallel to a series of indoor and outdoor irradiation tests on plants, the influence of microwave irradiation on the growth pattern of albino mouse will be conducted. This experiment will be the first experimental evaluation for the influence of microwave irradiation on animals.

  4. Infrared spectroscopy study of irradiated PVDF

    SciTech Connect

    Chappa, Veronica; Grosso, Mariela del; Garcia Bermudez, Gerardo; Behar, Moni

    2007-10-26

    The effects induced by 1 MeV/amu ion irradiations were compared to those induced by 4-12 MeV/amu irradiations. Structural analysis with infrared spectroscopy (FTIR) was carried out on PVDF irradiated using C and He beams with different fluences. From these spectra it was observed, as a function of fluence, an overall destruction of the polymer, amorphization of the crystalline regions and the creation of in-chain unsaturations. The track dimensions were determined using a previously developed Monte Carlo simulation code and these results were compared to a semiempirical model.

  5. Laser Irradiated Growth of Protein Crystal

    NASA Astrophysics Data System (ADS)

    Adachi, Hiroaki; Takano, Kazufumi; Hosokawa, Youichiroh; Inoue, Tsuyoshi; Mori, Yusuke; Matsumura, Hiroyoshi; Yoshimura, Masashi; Tsunaka, Yasuo; Morikawa, Masaaki; Kanaya, Shigenori; Masuhara, Hiroshi; Kai, Yasushi; Sasaki, Takatomo

    2003-07-01

    We succeeded in the first ever generation of protein crystals by laser irradiation. We call this process Laser Irradiated Growth Technique (LIGHT). Effective crystallization was confirmed by applying an intense femtosecond laser. The crystallization period was dramatically shortened by LIGHT. In addition, protein crystals were obtained by LIGHT from normally uncrystallized conditions. These results indicate that intense femtosecond laser irradiation generates crystal nuclei; protein crystals can then be grown from the nuclei that act as seeds in a supersaturated solution. The nuclei formation is possible primarily due to nonlinear nucleation processes of an intense femtosecond laser with a peak intensity of over a gigawatt (GW).

  6. Total body calcium analysis. [neutron irradiation

    NASA Technical Reports Server (NTRS)

    Lewellen, T. K.; Nelp, W. B.

    1974-01-01

    A technique to quantitate total body calcium in humans is developed. Total body neutron irradiation is utilized to produce argon 37. The radio argon, which diffuses into the blood stream and is excreted through the lungs, is recovered from the exhaled breath and counted inside a proportional detector. Emphasis is placed on: (1) measurement of the rate of excretion of radio argon following total body neutron irradiation; (2) the development of the radio argon collection, purification, and counting systems; and (3) development of a patient irradiation facility using a 14 MeV neutron generator. Results and applications are discussed in detail.

  7. Hyperparathyroidism following head and neck irradiation

    SciTech Connect

    Rao, S.D.; Frame, B.; Miller, M.J.; Kleerskoper, M.; Block, M.A.; Parfitt, A.M.

    1980-02-01

    A history of head and neck irradiation in childhood or adolescence was found in 22 of 130 patients with primary hyperparathyroidism compared with only 12 of 400 control patients. Among 200 patients with a known history of childhood irradiation, biochemical or surgical evidence of hyperparathyroidism was found in ten, a prevalence of 5%. This is at least 30 times the prevalence of hyperparathyroidism in the general population. The data indicate that head and neck irradiation should be regarded as an important risk factor in the subsequent development of hyperparathyroidism.

  8. Gamma-ray irradiated polymer optical waveguides

    SciTech Connect

    Lai, C.-C.; Wei, T.-Y.; Chang, C.-Y.; Wang, W.-S.; Wei, Y.-Y.

    2008-01-14

    Optical waveguides fabricated by gamma-ray irradiation on polymer through a gold mask are presented. The gamma-ray induced index change is found almost linearly dependent on the dose of the irradiation. And the measured propagation losses are low enough for practical application. Due to the high penetrability of gamma ray, uniform refractive index change in depth can be easily achieved. Moreover, due to large-area printing, the uniformity of waveguide made by gamma-ray irradiation is much better than that by e-beam direct writing.

  9. Processing Irradiated Beryllium For Disposal

    SciTech Connect

    T. J. Tranter; R. D. Tillotson; N. R. Mann; G. R. Longhurst

    2005-11-01

    The purpose of this research was to develop a process for decontaminating irradiated beryllium that will allow it to be disposed of through normal radwaste channels. Thus, the primary objectives of this ongoing study are to remove the transuranic (TRU) isotopes to less than 100 nCi/g and remove {sup 60}Co, and {sup 137}Cs, to levels that will allow the beryllium to be contact handled. One possible approach that appears to have the most promise is aqueous dissolution and separation of the isotopes by selected solvent extraction followed by precipitation, resulting in a granular form for the beryllium that may be fixed to prevent it from becoming respirable and therefore hazardous. Beryllium metal was dissolved in nitric and fluorboric acids. Isotopes of {sup 241}Am, {sup 239}Pu, {sup 85}Sr, and {sup 137}Cs were then added to make a surrogate beryllium waste solution. A series of batch contacts was performed with the spiked simulant using chlorinated cobalt dicarbollide (CCD) and polyethylene glycol diluted with sulfone to extract the isotopes of Cs and Sr. Another series of batch contacts was performed using a combination of octyl (phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) in tributyl phosphate (TBP) diluted with dodecane for extracting the isotopes of Pu and Am. The results indicate that greater than 99.9% removal can be achieved for each isotope with only three contact stages.

  10. Première expérience de l'utilisation du Misoprostol comme soin après avortement (SAA) à Libreville, Gabon

    PubMed Central

    Mayi-Tsonga, Sosthène; Minkobame, Ulysse; Mbila, Arielle; Assoumou, Pamphile; Diop, Ayisha; Winikoff, Beverly

    2014-01-01

    Introduction Une étude a été menée afin de déterminer le taux d'acceptabilité de 400µg de misoprostol par voie sublinguale comme traitement de première intention de l'avortement incomplet et de préciser le taux d'avortement complet ou vacuité utérine. Méthodes Les femmes éligibles avaient un diagnostic clinique d'avortement incomplet avec une taille utérine inférieure à celle d'un utérus de 12 semaines d'aménorrhées (SA). Chacune a reçu 400µg de misoprostol par voie sublinguale. Les femmes ont été revues après une semaine. A J7, celles qui n'avaient pas complètement expulsé ont eu le choix entre une nouvelle consultation de suivi à J14 et la pratique d'une évacuation chirurgicale immédiate. Résultats 145 patientes ont été éligibles et ont toutes accepté la méthode (100%). L’âge moyen était de 25,9 ± 6 ans. A J7, 120 patientes étaient guéries (85,7%). A J14, le taux de réussitea été de 95,7% soit 134 patientes guéries. Les patientes guéries ont déclaré être très satisfaites (57,5%), satisfaites (41,8%) et insatisfaite (0,7%). Au total,128 femmes (95,5%) ont dit être prêtes à utiliser de nouveau le misoprostol comme méthode d’évacuation utérine en cas d'avortement incomplet. Conclusion L’étude démontre que le 400µg misoprostol par voie sublinguale nous permet de prendre en charge d'une manière adéquate l'avortement incomplet surtout dans les pays à faible ressource et notamment dans les structures sanitaires de première ligne ou éloignées. PMID:25469194

  11. Surface Irradiances Consistent With CERES-Derived Top-of-Atmosphere Shortwave and Longwave Irradiances

    NASA Technical Reports Server (NTRS)

    Kato, Seiji; Loeb, Norman G.; Rose, Fred G.; Doelling, David R.; Rutan, David A.; Caldwell, Thomas E.; Yu, Lisan; Weller, Robert A.

    2013-01-01

    The estimate of surface irradiance on a global scale is possible through radiative transfer calculations using satellite-retrieved surface, cloud, and aerosol properties as input. Computed top-of-atmosphere (TOA) irradiances, however, do not necessarily agree with observation-based values, for example, from the Clouds and the Earth's Radiant Energy System (CERES). This paper presents amethod to determine surface irradiances using observational constraints of TOA irradiance from CERES. A Lagrange multiplier procedure is used to objectively adjust inputs based on their uncertainties such that the computed TOA irradiance is consistent with CERES-derived irradiance to within the uncertainty. These input adjustments are then used to determine surface irradiance adjustments. Observations by the Atmospheric Infrared Sounder (AIRS), Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO), CloudSat, andModerate Resolution Imaging Spectroradiometer (MODIS) that are a part of the NASA A-Train constellation provide the uncertainty estimates. A comparison with surface observations from a number of sites shows that the bias [root-mean-square (RMS) difference] between computed and observed monthlymean irradiances calculated with 10 years of data is 4.7 (13.3) W/sq m for downward shortwave and 22.5 (7.1) W/sq m for downward longwave irradiances over ocean and 21.7 (7.8) W m22 for downward shortwave and 21.0 (7.6) W/sq m for downward longwave irradiances over land. The bias andRMS error for the downward longwave and shortwave irradiances over ocean are decreased from those without constraint. Similarly, the bias and RMS error for downward longwave over land improves, although the constraint does not improve downward shortwave over land. This study demonstrates how synergetic use of multiple instruments (CERES,MODIS, CALIPSO, CloudSat, AIRS, and geostationary satellites) improves the accuracy of surface irradiance computations.

  12. Irradiated foods: current trends and technologies

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Additional demands on keeping food safe and palatable through longer distribution chains have led industry executives to reconsider irradiation and other technologies as viable processing alternatives for many foods. Other intervention technologies (precision thermal, UV, and novel sanitizer formula...

  13. He-Ne laser extravascular irradiation therapy

    NASA Astrophysics Data System (ADS)

    Chen, Rong; Chen, Huifang; Xie, Shusen; Chen, Yanjiao; Zhang, Yanrong

    2000-10-01

    Based on the study of tissue optics related with the laser irradiation blood therapy, a new treatment method, extravascular low-level laser irradiation therapy (ELLLI) is developed. The veins of 30 patients with cerebrovascular disease combined with diabetes, asthma were treated by He-Ne laser (632.8nm, 25mW) which was delivered by an optics fiber. The fiber was outside the patient's skin and the laser irradiated on the blood vessel perpendicularly. The therapy time was 60 minutes each time and about 7-10 times a course of the treatment. The values of blood sugar, blood- fat and hemorrheology were measured as the effective indexes. After the treatment the effective indexes and the symptoms of the patients were all improved. With the advantages of simplicity and safety (no medical infection), laser extravascular irradiation therapy is likely to be a new medical method for heart brain and other diseases.

  14. Laser irradiation of carbon-tungsten materials

    NASA Astrophysics Data System (ADS)

    Marcu, A.; Avotina, L.; Marin, A.; Lungu, C. P.; Grigorescu, C. E. A.; Demitri, N.; Ursescu, D.; Porosnicu, C.; Osiceanu, P.; Kizane, G.; Grigoriu, C.

    2014-09-01

    Carbon-tungsten layers deposited on graphite by thermionic vacuum arc (TVA) were directly irradiated with a femtosecond terawatt laser. The morphological and structural changes produced in the irradiated area by different numbers of pulses were systematically explored, both along the spots and in their depths. Although micro-Raman and Synchrotron-x-ray diffraction investigations have shown no carbide formation, they have shown the unexpected presence of embedded nano-diamonds in the areas irradiated with high fluencies. Scanning electron microscopy images show a cumulative effect of the laser pulses on the morphology through the ablation process. The micro-Raman spatial mapping signalled an increased percentage of sp3 carbon bonding in the areas irradiated with laser fluencies around the ablation threshold. In-depth x-ray photoelectron spectroscopy investigations suggested a weak cumulative effect on the percentage increase of the sp2-sp3 transitions with the number of laser pulses just for nanometric layer thicknesses.

  15. Neoplasia in fast neutron-irradiated beagles

    SciTech Connect

    Bradley, E.W.; Zook; B.C.; Casarett, G.W.

    1981-09-01

    One hundred fifty-one beagle dogs were irradiated with either photons or fast neutrons (15 MeV) to one of three dose-limiting normal tissues - spinal cord, lung, or brain. The radiation was given in four fractions per week for 5 weeks (spinal cord), 6 weeks (lung), 7 weeks (brain) to total doses encompassing those given clinically for cancer management. To date, no nonirradiated dogs or photon-irradiated dogs have developed neoplasms within the irradiated field. Of the neutron-irradiated dogs at risk, the incidence of neoplasia was 15%. The latent period for radiation-induced cancers has varied from 1 to 4 1/2 years at this time in the study.

  16. Neoplasia in fast neutron-irradiated beagles

    SciTech Connect

    Bradley, E.W.; Zook, B.C.; Casarett, G.W.; Deye, J.A.; Adoff, L.M.; Rogers, C.C.

    1981-09-01

    One hundred fifty-one beagle dogs were irradiated with either photons or fast neutrons (15 MeV) to one of three dose-limiting normal tissues--spinal cord, lung, or brain. The radiation was given in four fractions per week for 5 weeks (spinal cord), 6 weeks (lung), or 7 weeks (brain) to total doses encompassing those given clinically for cancer management. To date, no nonirradiated dogs or photon-irradiated dogs have developed any neoplasms. Seven dogs receiving fast neutrons have developed 9 neoplasms within the irradiated field. Of the neutron-irradiated dogs at risk, the incidence of neoplasia was 15%. The latent period for radiation-induced cancers has varied from 1 to 4 1/2 years at this time in the study.

  17. Irradiated Shellfish: Identification by Photostimulated Luminescence

    PubMed Central

    Di Schiavi, Maria Teresa; Falconi, Grazia; Verità, Francesca Della; Cavallina, Roberta

    2014-01-01

    The irradiation of food is a technology used in the industry to prevent the deterioration of foodstuff in some countries. The European Community legislation states that each Member State must carry out annual checks on the products during commercialisation. The Istituto Zooprofilattico Sperimentale delle regioni Lazio e Toscana (Rome, Italy) has developed and validated the screening method of photostimulated luminescence UNI EN 13751:2009 to identify irradiated shellfish. A total of 30 tests of shellfish samples, consisting of 22 certified as irradiated and 8 not-irradiated samples, were performed. The validation procedure was based on sensitivity and specificity; the compatibility between the screening method and the reference standard EN 13751:2009 was evaluated. Data were processed: 100% sensitivity and 100% specificity were obtained. Results obtained in our laboratory were perfectly compatible with the reference standard. For this reason, the method has been validated and proved to be suitable for its intended use. PMID:27800335

  18. Antioxidant tolerance of kidney after irradiation.

    PubMed

    Bukan, Neslihan; Güney, Yildiz; Hiçsönmez, Ayşe; Bilgihan, Ayşe

    2003-03-01

    Different doses of irradiation were performed in which group 1 (non-irradiated), group 2 (8 Gy/single dose/whole body) and group 3 (15 Gy/single dose/whole body) were formed of guinea pigs. After 24 hr of radiation exposure the levels of lipid peroxidation product, malondialdehyde, (MDA), glutathione (GSH) and activities of superoxide dismutase (SOD) and glutathione peroxidase (GSH-Px) were measured in the whole kidney. The MDA content increased in animals irradiated with 8 and 15 Gy. And group 3 showed an increase the level of MDA. GSH contents of kidney in group 2 and 3 increased. The activity of SOD decreased markedly in group 3 when compared with control group. The activity of GSH-Px decreased significantly in group 2 and group 3 in comparison to controls. It may be concluded that a high dose of ionizing irradiation cause excessive oxidative stress in kidney.

  19. IRRADIATION METHOD OF CONVERTING ORGANIC COMPOUNDS

    DOEpatents

    Allen, A.O.; Caffrey, J.M. Jr.

    1960-10-11

    A method is given for changing the distribution of organic compounds from that produced by the irradiation of bulk alkane hydrocarbons. This method consists of depositing an alkane hydrocarbon on the surface of a substrate material and irradiating with gamma radiation at a dose rate of more than 100,000 rads. The substrate material may be a metal, metal salts, metal oxides, or carbons having a surface area in excess of 1 m/sup 2//g. The hydrocarbons are deposited in layers of from 0.1 to 10 monolayers on the surfaces of these substrates and irradiated. The product yields are found to vary from those which result from the irradiation of bulk hydrocarbons in that there is an increase in the quantity of branched hydrocarbons.

  20. Hardness Evolution of Gamma-Irradiated Polyoxymethylene

    NASA Astrophysics Data System (ADS)

    Hung, Chuan-Hao; Harmon, Julie P.; Lee, Sanboh

    2016-12-01

    This study focuses on analyzing hardness evolution in gamma-irradiated polyoxymethylene (POM) exposed to elevated temperatures after irradiation. Hardness increases with increasing annealing temperature and time, but decreases with increasing gamma ray dose. Hardness changes are attributed to defects generated in the microstructure and molecular structure. Gamma irradiation causes a decrease in the glass transition temperature, melting point, and extent of crystallinity. The kinetics of defects resulting in hardness changes follow a first-order structure relaxation. The rate constant adheres to an Arrhenius equation, and the corresponding activation energy decreases with increasing dose due to chain scission during gamma irradiation. The structure relaxation of POM has a lower energy barrier in crystalline regions than in amorphous ones. The hardness evolution in POM is an endothermic process due to the semi-crystalline nature of this polymer.

  1. Thermoluminescence properties of irradiated chickpea and corn

    NASA Astrophysics Data System (ADS)

    Necmeddin Yazici, A.; Bedir, Metin; Bozkurt, Halil; Bozkurt, Hüseyin

    2008-02-01

    A study was carried out to establish a detection method for irradiated chickpea and corn by thermoluminescence (TL) method. The leguminous were packed in polyethylene bags and then the packets were irradiated at room temperature at different doses by 60Co gamma source at 1, 4, 8 and 10 kGy. Minerals extracted from the leguminous were deposited onto a clean aluminum disc and TL intensities of the minerals were measured by TL. It was observed that the extracted samples from both leguminous exhibit good TL Intensity and the TL intensity of glow curves of them increased proportionally to irradiation doses. The TL glow curve of both irradiated leguminous presents a single broad peak below 400 °C. The TL trapping parameters glow peaks were estimated by the additive dose (AD), Tm(Ea)-Tstop and computerized glow curve deconvolution (CGCD) methods. The fading characteristics of glow curves were also recorded up to 6 months.

  2. Food Irradiation: Is It Safe and Wholesome?

    ERIC Educational Resources Information Center

    Rebus, Shirley

    1990-01-01

    Addresses some of the major issues of food irradiation with respect to safety and wholesomeness, including formation of radiolytic products, effects on nutrients, prevention of food-borne illness, development of radiation-resistant bacteria, and formation of afaltoxins. (Author)

  3. Total lymphoid irradiation in alloimmunity and autoimmunity

    SciTech Connect

    Strober, S.

    1987-12-01

    Total lymphoid irradiation has been used as an immunosuppressive regimen in autoimmune disease and organ transplantation. The rationale for its use originated from studies of patients with Hodgkin disease, in whom this radiotherapy regimen was noted to induce profound and long-lasting immune suppression and yet was well tolerated, with few long-term side effects. Total lymphoid irradiation is a unique immunosuppressive regimen that produces a selective (and long-lasting) reduction in the number and function of helper T cells and certain subsets of B cells. Conventional immunosuppressive drugs show little selectivity, and their effects are short-lived. The most important aspect of total lymphoid irradiation is the potential for achieving transplantation tolerance and permanent remissions in autoimmune disease in laboratory animals. Attempts are being made to achieve similar goals in humans given total lymphoid irradiation, so that immunosuppressive drugs can be ultimately withdrawn from transplant recipients and patients with lupus nephritis. 28 references.

  4. Polymer Morphological Change Induced by Terahertz Irradiation.

    PubMed

    Hoshina, Hiromichi; Suzuki, Hal; Otani, Chiko; Nagai, Masaya; Kawase, Keigo; Irizawa, Akinori; Isoyama, Goro

    2016-06-07

    As terahertz (THz) frequencies correspond to those of the intermolecular vibrational modes in a polymer, intense THz wave irradiation affects the macromolecular polymorph, which determines the polymer properties and functions. THz photon energy is quite low compared to the covalent bond energy; therefore, conformational changes can be induced "softly," without damaging the chemical structures. Here, we irradiate a poly(3-hydroxybutylate) (PHB) / chloroform solution during solvent casting crystallization using a THz wave generated by a free electron laser (FEL). Morphological observation shows the formation of micrometer-sized crystals in response to the THz wave irradiation. Further, a 10-20% increase in crystallinity is observed through analysis of the infrared (IR) absorption spectra. The peak power density of the irradiating THz wave is 40 MW/cm(2), which is significantly lower than the typical laser intensities used for material manipulation. We demonstrate for the first time that the THz wave effectively induces the intermolecular rearrangement of polymer macromolecules.

  5. Food Irradiation Update and Cost Analysis

    DTIC Science & Technology

    1991-11-01

    poultry 3kGy Control Salrnl’..a products and other bacteria Fresh fruits and vegetables ikGy Inhibit growth and maturation Wheat, rice, barley, fruit...to the chilled non-irradiated product. Strawberries are frequently attacked by the fungi Botrytis cinerea Pers. ex Fr., or "gray mold", which can...Low dose irradiation delays ripening or mold growth , and therefore extends the shelf life of some fruits and vegetables. Apples, cherries, peaches

  6. Neutron Irradiation Resistance of RAFM Steels

    SciTech Connect

    Gaganidze, Ermile; Dafferner, Bernhard; Aktaa, Jarir

    2008-07-01

    The neutron irradiation resistance of the reduced-activation ferritic/martensitic (RAFM) steel EUROFER97 and international reference steels (F82H-mod, OPTIFER-Ia, GA3X and MANET-I) have been investigated after irradiation in the Petten High Flux Reactor up to 16.3 dpa at different irradiation temperatures (250-450 deg. C). The embrittlement behavior and hardening are investigated by instrumented Charpy-V tests with sub-size specimens. Neutron irradiation-induced embrittlement and hardening of EUROFER97 was studied under different heat treatment conditions. Embrittlement and hardening of as-delivered EUROFER97 steel are comparable to those of reference steels. Heat treatment of EUROFER97 at a higher austenitizing temperature substantially improves the embrittlement behaviour at low irradiation temperatures. Analysis of embrittlement vs. hardening behavior of RAFM steels within a proper model in terms of the parameter C={delta}DBTT/{delta}{sigma} indicates hardening-dominated embrittlement at irradiation temperatures below 350 deg. C with 0.17 {<=} C {<=} 0.53 deg. C/MPa. Scattering of C at irradiation temperatures above 400 deg. C indicates non hardening embrittlement. A role of He in a process of embrittlement is investigated in EUROFER97 based steels, that are doped with different contents of natural B and the separated {sup 10}B-isotope (0.008-0.112 wt.%). Testing on small scale fracture mechanical specimens for determination of quasi-static fracture toughness will be also presented in a view of future irradiation campaigns. (authors)

  7. Gamma irradiation effects in W films

    SciTech Connect

    Claro, Luiz H.; Santos, Ingrid A.; Silva, Cassia F.

    2013-05-06

    Using the van Der Pauw methodology, the surface resistivity of irradiated tungsten films deposited on Silicon substrate was measured. The films were exposed to {gamma} radiation using a isotopic {sup 60}Co source in three irradiation stages attaining 40.35 kGy in total dose. The obtained results for superficial resistivity display a time annealing features and their values are proportional to the total dose.

  8. Brain fibronectin expression in prenatally irradiated mice

    SciTech Connect

    Meznarich, H.K.; McCoy, L.S.; Bale, T.L.; Stiegler, G.L.; Sikov, M.R. )

    1993-01-01

    Activation of gene transcription by radiation has been recently demonstrated in vivo. However, little is known on the specificity of these alterations on gene transcription. Prenatal irradiation is a known teratogen that affects the developing mammalian central nervous system (CNS). Altered neuronal migration has been suggested as a mechanism for abnormal development of prenatally irradiated brains. Fibronectin (FN), an extracellular glycoprotein, is essential for neural crest cell migration and neural cell growth. In addition, elevated levels of FN have been found in the extracellular matrix of irradiated lung. To test whether brain FN is affected by radiation, either FN level in insoluble matrix fraction or expression of FN mRNA was examined pre- and postnatally after irradiation. Mice (CD1), at 13 d of gestation (DG), served either as controls or were irradiated with 14 DG, 17 DG, or 5,6, or 14 d postnatal. Brain and liver were collected from offspring and analyzed for either total FN protein levels or relative mRNAs for FN and tubulin. Results of prenatal irradiation on reduction of postnatal brain weight relative to whole are comparable to that reported by others. Insoluble matrix fraction (IMF) per gram of brain, liver, lung, and heart weight was not significantly different either between control and irradiated groups or between postnatal stages, suggesting that radiation did not affect the IMF. However, total amounts of FN in brain IMF at 17 DG were significantly different (p < .02) between normal (1.66 [+-] 0.80 [mu]g) and irradiated brains (0.58 [+-] 0.22 [mu]g). FN mRNA was detectable at 13, 14, and 17 DG, but was not detectable at 6 and 14 d postnatal, indicating that FN mRNA is developmentally regulated. 41 refs., 4 figs., 3 tabs.

  9. Irradiance analyzer for high power lasers

    SciTech Connect

    Conrad, R.W.

    1981-04-07

    An irradiance analysis system which includes an array of square rods that are joined together and have a flat entrance end and a polished flat exit end through which visible light is transmitted to a fresnel lens and focused to a particular area where the image focused is photographed so that when the various frames are developed they can be analyzed in a conventional film densitometer to yield quantative data on the temporal variation of laser beam irradiance distributions.

  10. Preserved irradiated homologous cartilage for orbital reconstruction

    SciTech Connect

    Linberg, J.V.; Anderson, R.L.; Edwards, J.J.; Panje, W.R.; Bardach, J.

    1980-07-01

    Human costal cartilage is an excellent implant material for orbital and periorbital reconstruction because of its light weight, strength, homogeneous consistency and the ease with which it can be carved. Its use has been limited by the necessity of a separate surgical procedure to obtain the material. Preserved irradiated homologous cartilage has been shown to have almost all the autogenous cartilage and is convenient to use. Preserved irradiated homologous cartilage transplants do not elicit rejection reactions, resist infection and rarely undergo absorption.

  11. Van de Graaff Irradiation of Materials

    SciTech Connect

    Quigley, Kevin; Chemerisov, Sergey; Tkac, Peter; Vandegrift, George F.

    2016-10-01

    Through irradiations using our 3 MeV Van de Graaf accelerator, Argonne is testing the radiation stability of components of equipment that are being used to dispense molybdenum solutions for use as feeds to 99mTc generators and in the 99mTc generators themselves. Components have been irradiated by both a direct electron beam and photons generated from a tungsten convertor.

  12. Food Irradiation | RadTown USA | US EPA

    EPA Pesticide Factsheets

    2016-02-23

    Using radiation to kill bacteria and other pathogens in food is called food irradiation. Irradiating food kills bacteria and molds that can make people sick. Irradiation does not remove toxins that are already in food. The high energy of the radiation breaks chemical bonds to stop bacteria and other pathogens from multiplying. Irradiation does not make food radioactive.

  13. Irradiation of municipal sludge for agricultural use

    NASA Astrophysics Data System (ADS)

    Ahlstrom, Scott B.

    Research has demonstrated that irradiation is an effective means for reducing pathogens in sewage sludge to levels where sludge reuse in public areas meets criteria for protection of the public health. Complementary research has demonstrated the value of the irradiated sludge in both agronomic and animal science applications. The benefits of sludge application to cropland are well documented. The irradiation process does not increase the extractability and plant uptake of a broad range of nutrients and heavy metals from sludge-amended soils. However, it does eliminate the hazards associated with pathogen contamination when applying sludge to agricultural land. Irradiated sludge has also been evaluated as a supplemental foodstuff for cattle and sheep. The data indicate that products derived from raw sewage may have a substantial nutritive value for ruminant animals. Irradiation of sewage sludge is a practical means of sludge disinfection. Where a highly disinfected sludge is required, it should be considered as a viable sludge management alternative. Evaluation of sludge irradiation technology and its associated costs must be done with consideration of other sludge treatment processes to develop an acceptable sludge management system.

  14. Total lymphoid irradiation and discordant cardiac xenografts

    SciTech Connect

    Kaplan, E.; Dresdale, A.R.; Diehl, J.T.; Katzen, N.A.; Aronovitz, M.J.; Konstam, M.A.; Payne, D.D.; Cleveland, R.J. )

    1990-01-01

    Total lymphoid irradiation can prolong concordant cardiac xenografts. The effects of total lymphoid irradiation in a discordant xenograft model (guinea pig to rat) were studied with and without adjuvant pharmacologic immunosuppression. Inbred Lewis rats were randomly allocated to one of four groups. Group 1 (n = 6) served as a control group and rats received no immunosuppression. Group 2 (n = 5) received triple-drug therapy that consisted of intraperitoneal azathioprine (2 mg/kg), cyclosporine (20 mg/kg), and methylprednisolone (1 mg/kg) for 1 week before transplantation. Group 3 animals (n = 5) received 15 Gy of total lymphoid irradiation in 12 divided doses over a 3-week period. Group 4 (n = 6) received both triple-drug therapy and total lymphoid irradiation as described for groups 2 and 3. Complement-dependent cytotoxicity assay was performed to determine if a correlation between complement-dependent cytotoxicity and rejection-free interval existed. Rejection was defined as cessation of graft pulsation and was confirmed by histologic test results. Only groups 1 and 2 showed a difference in survival (group 1, 6.9 +/- 1.0 minutes; group 2, 14.2 +/- 2.7 minutes, p = 0.02). Although total lymphoid irradiation did decrease complement-dependent cytotoxicity, linear regression revealed no correlation between complement-dependent cytotoxicity and graft survival (coefficient of correlation, 0.30). Unlike concordant cardiac xenografts, total lymphoid irradiation with or without triple-drug therapy does not prolong graft survival.

  15. [Light irradiator for various chronic pain].

    PubMed

    Ide, Yasuo

    2014-07-01

    Effects of light upon human tissue are divided into irreversible effects and reversible effects. Irreversible effects can be called as high level laser therapy (HLLT), and reversible effects can be called as low level light therapy (LLLT). Light irradiators for chronic pain act under principle of LLLT. Laser diode, halogen lamp and xenon lamp are used as light sources for light irradiator for various chronic pain. These days, light emitting diode (LED) is used as light source for light irradiator for various kinds of pain. Light irradiators are now divided into portable light weight low power machine and heavy weight, high power machine. In the dental area Nd : YAG laser is using as HLLT tool. But, now there are many reports about Nd : YAG laser used as anesthetic machine. In these reports, topical anesthetic effects of Nd : YAG laser are immediate and with fewer side effects compared with topical anesthetic agents. These effects are explained as LLLT. Halogen lamp and xenon lamp type irradiators were also introduced. MEDILASER SOFT PULSE10, an laser diode type irradiator was withdrawn from the market.

  16. Irradiated Nuclear Fuel Management: Resource Versus Waste

    SciTech Connect

    Nash, Kenneth L.; Lumetta, Gregg J.; Vienna, John D.

    2013-01-01

    Management of irradiated fuel is an important component of commercial nuclear power production. Although it is broadly agreed that the disposition of some fraction of the fuel in geological repositories will be necessary, there is a range of options that can be considered that affect exactly what fraction of material will be disposed in that manner. Furthermore, until geological repositories are available to accept commercial irradiated fuel, these materials must be safely stored. Temporary storage of irradiated fuel has traditionally been conducted in storage pools, and this is still true for freshly discharged fuel. Criticality control technologies have led to greater efficiencies in packing of irradiated fuel into storage pools. With continued delays in establishing permanent repositories, utilities have begun to move some of the irradiated fuel inventory into dry storage. Fuel cycle options being considered worldwide include the once-through fuel cycle, limited recycle in which U and Pu are recycled back to power reactors as mixed oxide fuel, and advance partitioning and transmutation schemes designed to reduce the long term hazards associated with geological disposal from millions of years to a few hundred years. Each of these options introduces specific challenges in terms of the waste forms required to safely immobilize the hazardous components of irradiated fuel.

  17. A study on the effect of various design parameters on the natural circulation flow rate of the ex-vessel core catcher cooling system of EU-APR1400

    SciTech Connect

    Rhee, B. W.; Ha, K. S.; Park, R. J.; Song, J. H.

    2012-07-01

    In this paper, a study on the effect of various design parameters such as the channel gap width, heat flux distribution, down-comer pipe size and two-phase flow slip ratio on the natural circulation flow rate is performed based on a physical model for a natural circulation flow along the flow path of the ex-vessel core catcher cooling system of an EU-APR1400, and these effects on the natural circulation flow rate are analyzed and compared with the minimum flow rate required for the safe operation of the system. (authors)

  18. Amélioration de la calcinose tumorale de la main droite après para thyroïdectomie chez un hémodialysé chronique

    PubMed Central

    El Maghraoui, Jaouad; Hammou, Mohamed; Kabbali, Nadia; Arrayhani, Mohamed; Houssaini, Tariq Sqalli

    2016-01-01

    Les calcifications des tissus péri articulaires sont fréquentes chez les insuffisants rénaux chroniques en hémodialyse. Nous rapportons le cas d'un hémodialysé chronique depuis 10 ans qui a présenté une calcinose pseudo tumorale isolé à la main droite nettement améliorée après para thyroïdectomie. A travers cette observation, nous montrons l'impact du para thyroïdectomie sur la calcinose pseudo tumorale. PMID:27583094

  19. Dosimetry Formalism and Implementation of a Homogenous Irradiation Protocol to Improve the Accuracy of Small Animal Whole-Body Irradiation Using a 137Cs Irradiator.

    PubMed

    Brodin, N Patrik; Chen, Yong; Yaparpalvi, Ravindra; Guha, Chandan; Tomé, Wolfgang A

    2016-02-01

    Shielded Cs irradiators are routinely used in pre-clinical radiation research to perform in vitro or in vivo investigations. Without appropriate dosimetry and irradiation protocols in place, there can be large uncertainty in the delivered dose of radiation between irradiated subjects that could lead to inaccurate and possibly misleading results. Here, a dosimetric evaluation of the JL Shepard Mark I-68A Cs irradiator and an irradiation technique for whole-body irradiation of small animals that allows one to limit the between subject variation in delivered dose to ±3% are provided. Mathematical simulation techniques and Gafchromic EBT film were used to describe the region within the irradiation cavity with homogeneous dose distribution (100% ± 5%), the dosimetric impact of varying source-to-subject distance, and the variation in attenuation thickness due to turntable rotation. Furthermore, an irradiation protocol and dosimetry formalism that allows calculation of irradiation time for whole-body irradiation of small animals is proposed that is designed to ensure a more consistent dose delivery between irradiated subjects. To compare this protocol with the conventional irradiation protocol suggested by the vendor, high-resolution film dosimetry measurements evaluating the dose difference between irradiation subjects and the dose distribution throughout subjects was performed using phantoms resembling small animals. Based on these results, there can be considerable variation in the delivered dose of > ± 5% using the conventional irradiation protocol for whole-body irradiation doses below 5 Gy. Using the proposed irradiation protocol this variability can be reduced to within ±3% and the dosimetry formalism allows for more accurate calculation of the irradiation time in relation to the intended prescription dose.

  20. Single- and double-strand breaks induced in plasmid DNA irradiated by ultra-soft X-rays

    NASA Astrophysics Data System (ADS)

    Fayard, B.; Touati, A.; Sage, E.; Abel, F.; Champion, C.; Chetoui, A.

    1999-01-01

    In order to investigate the molecular consequences of a carbon K photo-ionization located on DNA, dry pBS plasmid samples were irradiated with ultra-soft X-rays at energies below and above the carbon K-threshold (E_K=278 eV). Single- and double-strand breaks (ssb and dsb) were quantified after resolution of the three plasmid forms (supercoiled, relaxed circular, linear) by gel electrophoresis. A factor of 1.2 was found between the doses required at 250 eV and 380 eV to induce the same number of dsb per plasmid. Dans le but d'étudier les conséquences à l'échelle moléculaire d'une photo- ionisation en couche K du carbone de l'ADN, des dépots de plasmides ont été irradiés à sec par des X ultra-mous d'énergies situées de part et d'autre du seuil d'ionisation en couche interne du carbone (E_K=278 eV). Les taux de cassures simple- et double-brin (ssb et dsb) ont été quantifiées après résolution des trois formes de plasmide (surenroulé, circulaire relaché, linéaire) par électrophorèse. Un facteur de 1.2 a été mesuré entre les doses nécessaires à 250 eV et 380 eV pour produire le même nombre de dsb par plasmide.

  1. A Solar Irradiance Climate Data Record

    NASA Astrophysics Data System (ADS)

    Coddington, O.; Lean, J. L.; Pilewskie, P.; Snow, M.; Lindholm, D.

    2016-08-01

    We present a new climate data record for total solar irradiance and solar spectral irradiance between 1610 and the present day with associated wavelength and time-dependent uncertainties and quarterly updates. The data record, which is part of the National Oceanic and Atmospheric Administration’s (NOAA) Climate Data Record (CDR) program, provides a robust, sustainable, and scientifically defensible record of solar irradiance that is of sufficient length, consistency, and continuity for use in studies of climate variability and climate change on multiple time scales and for user groups spanning climate modeling, remote sensing, and natural resource and renewable energy industries. The data record, jointly developed by the University of Colorado’s Laboratory for Atmospheric and Space Physics (LASP) and the Naval Research Laboratory (NRL), is constructed from solar irradiance models that determine the changes with respect to quiet sun conditions when facular brightening and sunspot darkening features are present on the solar disk where the magnitude of the changes in irradiance are determined from the linear regression of a proxy magnesium (Mg) II index and sunspot area indices against the approximately decade-long solar irradiance measurements of the Solar Radiation and Climate Experiment (SORCE). To promote long-term data usage and sharing for a broad range of users, the source code, the dataset itself, and supporting documentation are archived at NOAA's National Centers for Environmental Information (NCEI). In the future, the dataset will also be available through the LASP Interactive Solar Irradiance Data Center (LISIRD) for user-specified time periods and spectral ranges of interest.

  2. Removal of carbon-14 from irradiated graphite

    NASA Astrophysics Data System (ADS)

    Dunzik-Gougar, Mary Lou; Smith, Tara E.

    2014-08-01

    Approximately 250,000 tonnes of irradiated graphite waste exists worldwide and that quantity is expected to increase with decommissioning of Generation II reactors and deployment of Generation IV gas-cooled, graphite moderated reactors. This situation indicates the need for a graphite waste management strategy. On of the isotopes of great concern for long-term disposal of irradiated graphite is carbon-14 (14C), with a half-life of 5730 years. Study of irradiated graphite from some nuclear reactors indicates 14C is concentrated on the outer 5 mm of the graphite structure. The aim of the research presented here is to develop a practical method by which 14C can be removed. In parallel with these efforts, the same irradiated graphite material is being characterized to identify the chemical form of 14C in irradiated graphite. A nuclear-grade graphite, NBG-18, and a high-surface-area graphite foam, POCOFoam®, were exposed to liquid nitrogen (to increase the quantity of 14C precursor) and neutron-irradiated (1013 neutrons/cm2/s). During post-irradiation thermal treatment, graphite samples were heated in the presence of an inert carrier gas (with or without the addition of an oxidant gas), which carries off gaseous products released during treatment. Graphite gasification occurs via interaction with adsorbed oxygen complexes. Experiments in argon only were performed at 900 °C and 1400 °C to evaluate the selective removal of 14C. Thermal treatment also was performed with the addition of 3 and 5 vol% oxygen at temperatures 700 °C and 1400 °C. Thermal treatment experiments were evaluated for the effective selective removal of 14C. Lower temperatures and oxygen levels correlated to more efficient 14C removal.

  3. Preservation of food products by irradiation

    SciTech Connect

    McGivney, W.T.

    1988-01-01

    The use of irradiation to preserve food has the potential to significantly enhance our capacity to maximize the quality and quantity of the food we consume. In a world in which distribution of food occurs across continents and in which malnourished populations are in dire need of basic food products, any safe, effective, and efficient means of preserving food is more than welcome. Irradiation, as a method for food preservation, has been studied for more than 30 years. This discussion focuses on this most recent method for the preservation of food with particular emphasis on its effects on the safety, nutritive, and aesthetic values of the food preserved by irradiation. The use of ionizing radiation as a method to preserve foods is one that has been demonstrated to be effective for a variety of food classes. Irradiation offers a means to decontaminate, disinfest, and retard the spoilage of the food supply. At the same time, it appears that the wholesomeness of these food products is maintained. Nutritive value can be sustained by use of effective doses of radiation. Concerns over the safety of irradiated food are rooted in questions regarding the potential induction of radioactivity, harmful radiolytic products, and pathogenic radiation-resistant or mutant strains of microorganisms. Research findings have allayed concerns over safety. However, more research is necessary to conclusively resolve these safety issues. Food irradiation is a promising technology that has and will contribute to our ability to feed the people of this world. This technology is but one of many available ways to preserve our greatest natural resource, the food supply. Enhancement of the ability to preserve food by irradiation will facilitate the distribution of food from fertile developed regions to the malnourished peoples of underdeveloped countries. 21 references.

  4. The treatment of extensively burned patients and {beta} irradiational injury skin burn patients with irradiated pigskin

    SciTech Connect

    Tang Zhong Yi; Lu Xing An; Jing Ling; Qi Qiang

    1994-12-31

    Obvious therapeutic effects achieved by the covering of irradiation sterilized pigskin on burn wounds, escarectomized 3rd degree burn wounds and {beta} injured burns are introduced. The article introduces also the manufacture processes of irradiated pigskins and the selection of surgical treatments of various burns.

  5. Quality of gamma ray-irradiated iceberg lettuce and treatments to minimize irradiation-induced disorders

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Irradiation of Iceberg lettuce was recently approved by the FDA to enhance microbial safety and to extend shelf-life at doses up to 4 kGy. However, the radiation tolerance of whole head lettuce is unclear. The present study was conducted to investigate the effects of irradiation on the quality of he...

  6. Epidémiologie et facteurs de risque des complications respiratoires majeures après chirurgie de l'aorte abdominale au CHU Ibn Sina, Maroc

    PubMed Central

    Awab, Almahdi; Elahmadi, Brahim; Lamkinsi, Tarik; El Moussaoui, Rachid; El Hijri, Ahmed; Azzouzi, Abderrahim; Alilou, Mustapha

    2013-01-01

    Introduction L'incidence des complications respiratoires postopératoires (CRPO) reste très diversement appréciées selon les critères diagnostiques retenues dans les différentes études, ce qui la fait varier de 5 à plus de 50%. Les CRPO majeurs après chirurgie de l'aorte abdominale sont responsables d'une grande morbi-mortalité pouvant aller jusqu’à 36%, d'une durée d'hospitalisation et d'un coût plus importants. Ainsi dans l'optique d'améliorer notre prise en charge périopératoire de la chirurgie de l'aorte, nous avons décidé de mener une étude pour dresser le profil épidémiologique et déterminer les facteurs de risque des complications respiratoires dans notre contexte Méthodes Il s'agit d'une étude de cohorte rétrospective du mois de Janvier 2007 au mois de décembre 2011 portant sur l'ensemble des patients opérés pour pathologie aortique au bloc opératoire central de l'hôpital Ibn Sina de Rabat, Maroc. Résultats Cent vingt cinq patients ont été inclus dans notre étude, 24 patients ont été opérés pour anévrysme de l'aorte abdominale et 101 patients pour lésion occlusive aortoiliaque. Dans notre série 22 malades soit 17,6% ont présenté une complication respiratoire majeure avec, une reventilation dans 4,8% des cas, une difficulté de sevrage de la ventilation artificielle dans 3,2% des cas, une pneumopathie dans 4% des cas, un syndrome de détresse respiratoire aigue (SDRA) dans 4% des cas et une nécessité de fibroaspiration bronchique dans 1,6% des cas. En analyse univariée: l’âge, la présence d'une BPCO avec dyspnée stade 3 ou 4, la présence d'une anomalie à l'EFR préopératoire, la présence d'un stade avancé (III ou IV) de LOAI et la reprise chirurgicale étaient statistiquement associés à la survenue d'une complication respiratoire postopératoire. En analyse multivariée, seule une anomalie à l'EFR en préopératoire constituait un facteur de risque indépendant de survenue d'une complication

  7. Irradiation response on mechanical properties of neutron irradiated F82H

    NASA Astrophysics Data System (ADS)

    Shiba, K.; Suzuki, M.; Hishinuma, A.

    1996-10-01

    Tensile and Charpy impact properties of neutron irradiated F82H (Fe8Cr2WVTa) with and without boron have been investigated to obtain the basic irradiation response on mechanical properties in low damage regime less than 1 dpa at the temperature ranging from 300° to 590°C. Boron-doped steel was used for the helium effect due to (n, α) reaction. Typical irradiation hardening was observed at 300°C. The irradiation above 520°C did not reveal increase in yield stress, but the specimen irradiated at 590°C showed some reduction in elongation in room temperature tensile testing. Slight difference in the tensile properties between boron-doped and boron-free were observed at 590°C. No changes in ductile brittle transition temperature (DBTT) occurred at a temperature between 335° and 460°C by Charpy impact testing.

  8. The influence of Gamma Irradiation on flavonoïds content during storage of irradiated clementina

    NASA Astrophysics Data System (ADS)

    Oufedjikh, H.; Mahrouz, M.; Lacroix, M.; Amiot, M. J.; Taccini, M.

    1998-06-01

    The influence of Gamma irradiation on content of some important flavonoïds (flavonones glycosides and polymethoxylated flavones) was evaluated during storage of Moroccan clementina treated at a mean dose of 0.3 kGy and stored three months at 3'C. Results shows that at day one, gamma irradiation induced degradation of small quantities of these flavonoïds, however after 14 days of storage, the content of these compounds was significantly higher (p≤0.05) in irradiated samples. Irradiation stimulated biosynthesis of flavonoïds after 14 days of storage. Hesperidin was the major flavanones compounds in clementines. Nobiletin and Heptamethoxyflavone were the major polymethoxylated flavones in clementines. Our study demonstrated that the content of these compounds was significantly higher (p≤0.05) in irradiated samples.

  9. The volume effect in irradiated mouse colorectum

    NASA Astrophysics Data System (ADS)

    Skwarchuk, Mark William

    1997-11-01

    Damage of the colorectum is the dose-limiting normal tissue complication following radiotherapy of prostate and cervical cancers. One approach for decreasing complications is to physically reduce the treatment volume. Mathematical models have been previously developed to describe the change in associated toxicity with a change in irradiated volume, i.e. the 'volume effect', for serial-type normal tissues including the colorectum. The first goal of this thesis was to test the hypothesis that there would not be a threshold length in the development of obstruction after irradiation of mouse colorectum, as predicted by the Probability model of the volume effect. The second goal was to examine if there were differences in the threshold and in the incidence of colorectal obstruction after irradiation of two mouse strains, C57B1/6 (C57) and C3Hf/Kam (C3H), previously found to be fibrosis-prone and-resistant, respectively, after lung irradiation due, in part, to genetic differences. The hypothesis examined was that differences in incidence between strains were due to the differential expression of the fibrogenic cytokines TGF/beta and TNF/alpha. Various lengths of C57 and C3H mouse colorectum were irradiated and the incidence of colorectal obstruction was followed up to 15 months. A threshold length was observed for both mouse strains, in contradiction of model predictions. The mechanism of the threshold was epithelial regeneration after irradiation. C57 mice had significantly higher incidence of colorectal obstruction compared to C3H mice, especially at smaller irradiated lengths. Colorectal tissue was obtained at various times after irradiation and prepared for histology, immunohistochemistry and RNase protection assay for measurement of TGF/beta 1, 2, 3 and TNF/alpha mRNA. Distinct strain differences in the histological time of appearance and spatial locations of fibrosis were observed. However, there were no consistent strain difference in mRNA levels or

  10. Effects of irradiation on platelet function

    SciTech Connect

    Rock, G.; Adams, G.A.; Labow, R.S.

    1988-09-01

    Current medical practice involves the irradiation of blood components, including platelet concentrates, before their administration to patients with severe immunosuppression. The authors studied the effect of irradiation on in vitro platelet function and the leaching of plasticizers from the bag, both immediately and after 5 days of storage. The platelet count, white cell count, pH, glucose, lactate, platelet aggregation and release reaction, and serotonin uptake were not altered by the irradiation of random-donor or apheresis units with 2000 rads carried out at 0 and 24 hours and 5 days after collection. The leaching of di(2-ethylhexyl)phthalate from the plastic bags followed by the conversion to mono(2-ethylhexyl)phthalate was not increased by irradiation. Therefore, it is possible to irradiate platelet concentrates on the day of collection and subsequently store them for at least 5 days while maintaining in vitro function. This procedure could have considerable benefit for blood banks involved in the provision of many platelet products.

  11. Measurement of Diameter Changes during Irradiation Testing

    SciTech Connect

    Davis, K. L.; Knudson, D. L.; Crepeau, J. C.; Solstad, S.

    2015-03-01

    New materials are being considered for fuel, cladding, and structures in advanced and existing nuclear reactors. Such materials can experience significant dimensional and physical changes during irradiation. Currently in the US, such changes are measured by repeatedly irradiating a specimen for a specified period of time and then removing it from the reactor for evaluation. The time and labor to remove, examine, and return irradiated samples for each measurement makes this approach very expensive. In addition, such techniques provide limited data and handling may disturb the phenomena of interest. In-pile detection of changes in geometry is sorely needed to understand real-time behavior during irradiation testing of fuels and materials in high flux US Material and Test Reactors (MTRs). This paper presents development results of an advanced Linear Variable Differential Transformer-based test rig capable of detecting real-time changes in diameter of fuel rods or material samples during irradiation in US MTRs. This test rig is being developed at the Idaho National Laboratory and will provide experimenters with a unique capability to measure diameter changes associated with fuel and cladding swelling, pellet-clad interaction, and crud buildup.

  12. Disinfestation of different cereal products by irradiation

    NASA Astrophysics Data System (ADS)

    Kovács, E.; Kiss, I.; Boros, A.; Horváth, Ny.; Tóth, J.; Gyulai, P.; Szalma, Á.

    The sensitivity of overlineTribolium confusum - small flour beetle - to radiation was studied in a dose range of 0-0.8 kGy. We found that the insect egg was the most sensitive to radiation, then larvae and pupae followed it. 0.2 kGy dose of irradiation kills these forms or their further development is inhibited. Imagoes do not immediately die after 0.8 kGy dose of irradiation; the young imagoes are more sensitive to radiation than the aged ones. 0.4 kGy average dose of irradiation is a suitable protection against overlineTribolium confusum. Disinfestation experiments were performed with wheat-germ and wheat-bran and parallelly the most important ingredients of the two products were analysed. The vitamin E content and the rate of lipid-oxidation of wheat germ were determined. The vitamin E content decreased after radiation treatment, however, during storage of at least 6 months, it remained at a level specified by food quality standards (higher than 10 mg%). Carbohydrate content of wheat-bran (water soluble carbohydrate content, crude-fibre and dietary fibre content) did not change at all. Storability of radiation disinfested wheat-germ was 8 months, wheat-bran 3-4 months. On the base of the results 2-2 tons of wheat-germ and wheat-bran were irradiated and trial marked in 1985. In 1986 the irradiation of 10 tons of wheat-germ is planned.

  13. Infrared Irradiation: Toward Green Chemistry, a Review

    PubMed Central

    Escobedo, René; Miranda, René; Martínez, Joel

    2016-01-01

    This review provides a comprehensive overview of where infrared irradiation has been employed, mainly as regards activating green mode for natural products extractions, as well as to favor a reaction, highlighting its actual importance. It is also underlined that infrared irradiation heating has been around for a long time; however, only in the last eighteen years have many of its advantages been applied to satisfy a wide range of chemical processes, natural products extractions, and for the promotion of many kinds of reactions. In addition, it is brought to light that near infrared irradiation is more efficient than middle and far infrared irradiations, being easily controllable and with the quality of a fast responding heat source. Thus, the main objective of this review is to offer infrared irradiation as an alternative clean energy source to activate reactions, in addition to favor the selective extraction of natural products, all of which is within the Green Chemistry protocol. Some recent results from our laboratory are also included. PMID:27023535

  14. Carotid artery disease following external cervical irradiation

    SciTech Connect

    Elerding, S.C.; Fernandez, R.N.; Grotta, J.C.; Lindberg, R.D.; Causay, L.C.; McMurtrey, M.J.

    1981-01-01

    A retrospective study of 910 patients surviving at least five years after cervical irradiation for Hodgkin's disease, non-Hodgkin's lymphoma, or primary head an neck neoplasms showed the incidence of stroke following cervical irradiation was 63 of 910 patients (6.3%) during a mean period of observation of nine years. This represents a trend toward an increased risk for this population observed over the same period of time (p . 0.39). A prospective study of 118 similar patients currently living five years after cervical radiotherapy was performed to determine the incidence of carotid artery disease occurring as a consequence of neck irradiation. Abnormal carotid phonangiograms (CPA) were found in 25% of the patients and abnormal oculoplethysmographs (OPG) were found in 17%. These studies represent significant carotid lesions that are not expected in such a population. It is concluded that the carotid stenoses demonstrated are most likely a consequence of prior irradiation. Patients that are five-year survivors of cervical irradiation should have noninvasive vascular laboratory studies performed as part of their routine follow-up examinations in order to detect these carotid lesions while they are occult.

  15. Carotid artery disease following external cervical irradiation

    SciTech Connect

    Elerding, S.C.; Fernandez, R.N.; Grotta, J.C.; Lindberg, R.D.; Causay, L.C.; McMurtrey, M.J.

    1981-11-01

    A retrospective study of 910 patients surviving at least five years after cervical irradiation for Hodgkin's disease, non-Hodgkin's lymphoma, or primary head and neck neoplasms showed the incidence of stroke following cervical irradiation was 63 of 910 patients (6.3%) during a mean period of observation of nine years. This represents a trend toward an increased risk for this population over the expected incidence of 38 strokes for a matched population observed over the same period of time (p = 0.39). A prospective study of 118 similar patients currently living five years after cervical radiotherapy was performed to determine the incidence of carotid artery disease occurring as a consequence of neck irradiation. Abnormal carotid phonoangiograms (CPA) were found in 25% of the patients and abnormal oculoplethysmographs (OPG) were found in 17%. These studies represent significant carotid lesions that are not expected in such a population. It is concluded that the carotid stenoses demonstrated are most likely a consequence of prior irradiation. Patients that are five-year survivors of cervical irradiation should have noninvasive vascular laboratory studies performed as part of their routine follow-up examinations in order to detect these carotid lesions while they are occult.

  16. The LASP Interactive Solar IRradiance Datacenter (LISIRD)

    NASA Astrophysics Data System (ADS)

    Snow, M.; Woods, T. N.; Eparvier, F. G.; Fontenla, J.; Harder, J.; McClintock, W. E.; Pankratz, C.; Richard, E.; Windnagel, A.; Woodraska, D.

    2005-12-01

    LASP has created an online resource for combined solar irradiance datasets from the SORCE, TIMED, UARS, and SME missions. The LASP Interactive Solar IRradiance Datacenter (LISIRD) not only provides unified access to the individual datasets, but also combines them for ease of use by scientists, educators, and the general public. In particular, LISIRD makes available composite spectra and time series. The TIMED SEE, SORCE SOLSTICE, and SORCE SIM instruments produce spectra that together cover the solar spectrum from 1 to 2700 nm. Through the LISIRD interface, the user can get data that bridges the various missions in both wavelength and time. LISIRD also hosts data products of interest to the space weather community. They have slightly different needs than the atmospheric modelers that are the typical users of irradiance data. For space weather applications, high time cadence and near real-time data delivery are key. For these users, we make our observations available shortly after spacecraft contact, and append the observations to a single data file which they can retrieve using anonymous ftp every few hours. The third component of LISIRD is the Solar Physical Radiation Model (SPRM) results of Fontenla et al. It provides a model of current solar activity, the synthetic spectral irradiance, and tools that permit one to model the solar activity source of the spectral irradiance variations.

  17. Infrared Irradiation: Toward Green Chemistry, a Review.

    PubMed

    Escobedo, René; Miranda, René; Martínez, Joel

    2016-03-26

    This review provides a comprehensive overview of where infrared irradiation has been employed, mainly as regards activating green mode for natural products extractions, as well as to favor a reaction, highlighting its actual importance. It is also underlined that infrared irradiation heating has been around for a long time; however, only in the last eighteen years have many of its advantages been applied to satisfy a wide range of chemical processes, natural products extractions, and for the promotion of many kinds of reactions. In addition, it is brought to light that near infrared irradiation is more efficient than middle and far infrared irradiations, being easily controllable and with the quality of a fast responding heat source. Thus, the main objective of this review is to offer infrared irradiation as an alternative clean energy source to activate reactions, in addition to favor the selective extraction of natural products, all of which is within the Green Chemistry protocol. Some recent results from our laboratory are also included.

  18. Cobalt-60 gamma irradiation of shrimp

    SciTech Connect

    Sullivan, N.L.B.

    1993-01-01

    Meta- and ortho-tyrosine were measured using high performance liquid chromatography (HPLC) in conjunction with electrochemical detection in shrimp irradiated using cobalt-60 gamma radiation in the absorbed dose range 0.8 to 6.0 kGy, in nonirradiated shrimp, and in bovine serum albumin (BSA) irradiated in dilute aqueous solution at 25.0 kGy. Ortho-tyrosine was measured in nonirradiated BSA. Para-, meta-, and ortho-tyrosine was measured using HPLC in conjunction with uv-absorption detection in dilute aqueous solutions of phenylalanine irradiated in the absorbed dose range 16.0 to 195.0 kGy. The measured yields of tyrosine isomers were approximately linear as a function of absorbed dose in shrimp, and in irradiated solutions of phenylalanine up to 37.0 kGy. The occurrence of meta- and ortho-tyrosine, which had formerly been considered unique radiolytic products, has not previously been reported in nonirradiated shrimp or BSA. The conventional hydrolyzation and analytical techniques used in the present study to measure meta- and ortho-tyrosine may provide the basis for a method to detect and determine the dose used in food irradiation.

  19. Ion irradiation effects on metallic nanocrystals

    SciTech Connect

    Kluth, P.; Johannessen, B.; Giulian, R.; Schnohr, C.S.; Foran, G.J.; Cookson, D.J.; Byrne, A.P.; Ridgway, M.C.

    2008-04-02

    We have investigated structural and morphological properties of metallic nanocrystals (NCs) exposed to ion irradiation. NCs were characterized by transmission electron microscopy in combination with advanced synchrotron-based analytical techniques, in particular X-ray absorption spectroscopy and small-angle X-ray scattering. A number of different effects were observed depending on the irradiation conditions. At energies where nuclear stopping is predominant, structural disorder/amorphization followed by inverse Ostwald ripening/dissolution due to ion beam mixing was observed for Au and Cu NCs embedded in SiO{sub 2}. The ion-irradiation-induced crystalline to amorphous transition in the NCs, which cannot be achieved in the corresponding bulk metals, was attributed to their initially higher structural energy as compared to bulk material and possibly preferential nucleation of the amorphous phase at the NC/SiO{sub 2} interface. At very high irradiation energies (swift heavy ion irradiation), where the energy loss is nearly entirely due to electronic stopping, a size-dependent shape transformation of the NCs from spheres to rod like shapes was apparent in Au NCs. Our preliminary results are in good agreement with considerations on melting of the NCs in the ion track as one mechanism involved in the shape transformation.

  20. Neoplasms in young dogs after perinatal irradiation

    SciTech Connect

    Benjamin, S.A.; Lee, A.C.; Angleton, G.M.; Saunders, W.J.; Miller, G.K.; Williams, J.S.; Brewster, R.D.; Long, R.I.

    1986-08-01

    For a study of the life-time effects of irradiation during development, 1,680 beagles were given single, whole-body exposures to /sup 60/Co gamma-radiation at one of three prenatal (preimplantation, embryonic, and fetal) or at one of three postnatal (neonatal, juvenile, and young adult) ages. Mean doses were 0, 0.16, or 0.83 Gy. For comparison with data on childhood cancer after prenatal irradiation, examination was made of tumors occurring in young dogs in this life-span experiment. Up to 4 years of age, 18 dogs had neoplasms diagnosed, 2 of these being in controls. Four dogs that were irradiated in the perinatal (late fetal or neonatal) period died of cancers prior to 2 years of age. This risk was of significant increase compared to the risks for other experimental groups and for the canine population in general. Overall, 71% (5 of 7) of all cancers and 56% (10 of 18) of all benign and malignant neoplasms seen in the first 4 years of life occurred in 29% (480 of 1680) of the dogs irradiated in the perinatal period. These data suggest an increased risk for neoplasia after perinatal irradiation in dogs.

  1. RESTORATION INDUCED BY CATALASE IN IRRADIATED MICROORGANISMS

    PubMed Central

    Latarjet, Raymond; Caldas, Luis Renato

    1952-01-01

    1. E. coli, strain K-12, and B. megatherium 899, irradiated in strict but still undefined physiological conditions with certain heavy doses of ultraviolet light, are efficiently restored by catalase, which acts on or fixes itself upon the bacteria in a few minutes. This restoration (C. R.), different from photorestoration, is aided by a little visible light. 2. At 37° the restorability lasts for about 2 hours after UV irradiation; the restored cells begin to divide at the same time as the normal survivors. 3. C. R. is not produced after x-irradiation. 4. B. megatherium Mox and E. coli, strain B/r show little C. R.; E. coli strain B shows none. None of these three strains is lysogenic, whereas the two preceding catalase-restorable strains are. 5. Phage production in the system "K-12 infected with T2 phage" is restored by catalase after UV irradiation, whereas phage production in the system "infected B" is not. 6. With K-12, catalase does not prevent the growth of phage and the lysis induced by UV irradiation (Lwoff's phenomenon). 7. Hypotheses are discussed concerning: (a) the chemical nature of this action of catalase; (b) a possible relation between C. R. and lysogenicity of the sensitive bacteria; (c) the consequences of such chemical restorations on the general problem of cell radiosensitivity. PMID:14898028

  2. Complications métaboliques après transplantation rénale à partir du donneur vivant: expérience du CHU Ibn Sina de Rabat

    PubMed Central

    Mouram, Hala; Benamar, Loubna; Ouzeddoune, Naima; Bayahia, Rabia; Ezaitouni, Fatima

    2014-01-01

    La transplantation rénale (TR) constitue le traitement de choix de l'insuffisance rénale chronique terminale. Les complications métaboliques après TR (diabète, dyslipidémie, hyperuricémie, obésité), en grande partie liées au traitement immunosuppresseur, deviennent une préoccupation car elles constituent un facteur de risque de morbimortalité et de perte fonctionnelle du greffon. Le but de notre étude est d’évaluer la fréquence de ces anomalies après TR. Il s'agit d'une étude rétrospective incluant tous les patients ayant bénéficié d'une première TR par donneur vivant (DV) de Juin 1998 à Décembre 2010. Nous avons recensé les données démographiques propres au receveur, le traitement immunosuppresseur après TR. Les paramètres clinico-biologiques recueillis sont (index de masse corporel (IMC), glycémie à jeun, hémoglobine glyquée, CT, C-HDL, C-LDL, TG, acide urique). Soixante dix patients ont été colligés, l’âge moyen est de 36.3 + /-9.6 ans (21 à 62) avec un sex ratio de 0.5. Quinze patients (21.4%) étaient hypertendus avant la TR et 2.9% avaient une néphropathie diabétiques. L’âge moyen du donneur est de 47.5 + /-10.2 ans (20-65). Le traitement immunosuppresseur pendant la phase d'induction était une trithérapie associant corticostéroïdes, anticalcineurines chez tous les patients et mycophénolate mofétil chez 68.6% et azathioprine dans 31.4% des cas. L'IMC moyen était de 24.1 + /-4.0 (16.9 à 37), 33% des patients étaient considérés en surpoids dont 21.8% en obésité. L'hypercholestérolémie, a été retrouvée chez 25 patients soit 36%. Presque la moitié des patients (48.5%) avaient une hyperuricémie. Quatre patients ont développé un diabète après TR soit 6% des cas. La perte du greffon a été notée chez 12 patients et 2 patients sont décédés dont un avec un greffon fonctionnel. En analyse univariée, l'hyperuricémie et la dyslipidémie ont été considérées comme facteur de risque de perte

  3. The effect of gamma irradiation on injectable human amnion collagen

    SciTech Connect

    Liu, B.C.; Harrell, R.; Davis, R.H.; Dresden, M.H.; Spira, M. )

    1989-08-01

    The effect of gamma irradiation on the physicochemical properties of injectable human amnion collagen was investigated. Pepsin-extracted human amnion collagen was purified, reconstituted, and irradiated with varying doses of gamma irradiation (0.25 Mrads to 2.5 Mrads). Gamma irradiation had a significant impact on the physical characteristics of the collagen. The neutral solubility of collagen in PBS at 45{degrees}C was decreased from 100% for the nonirradiated control sample to 16% for the 2.5 Mrads irradiated sample. SDS polyacrylamide gel electrophoresis also demonstrated the dose-dependent effect of gamma irradiation on collagen cross-links. Electron microscopic observation revealed that even at low irradiation dose (0.25 Mrads), collagen fibril diameter increased. The average diameter was 50 nm for nonirradiated control fibrils, while 4.4% of the irradiated collagen fibrils had a diameter greater than 100 nm. Irradiated collagen showed little evidence of damage. Well-preserved cross-striations were found in collagen fibrils at all doses of irradiation. Native amnion collagen irradiated with gamma rays demonstrated a slight increase in resistance to collagenase degradation compared with nonirradiated native collagen samples. Increased resistance to collagenase did not correlate with increasing irradiation dose. After 30 min of incubation at 37{degrees}C, both irradiated and nonirradiated collagen was completely digested by collagenase. However, gamma-irradiated collagen did become more sensitive to hydrolysis by trypsin. The higher the irradiation doses used, the greater sensitivity to trypsin was observed. At 0.25 Mrads irradiation only a slight increase was found. No marked differences in amino acid composition were noted among the high dose irradiated, low dose irradiated and control amnion collagen.

  4. Irradiation creep of vanadium-base alloys

    SciTech Connect

    Tsai, H.; Billone, M.C.; Strain, R.V.; Smith, D.L.; Matsui, H.

    1998-03-01

    A study of irradiation creep in vanadium-base alloys is underway with experiments in the Advanced Test Reactor (ATR) and the High Flux Isotope Reactor (HFIR) in the United States. Test specimens are thin-wall sealed tubes with internal pressure loading. The results from the initial ATR irradiation at low temperature (200--300 C) to a neutron damage level of 4.7 dpa show creep rates ranging from {approx}0 to 1.2 {times} 10{sup {minus}5}/dpa/MPa for a 500-kg heat of V-4Cr-4Ti alloy. These rates were generally lower than reported from a previous experiment in BR-10. Because both the attained neutron damage levels and the creep strains were low in the present study, however, these creep rates should be regarded as only preliminary. Substantially more testing is required before a data base on irradiation creep of vanadium alloys can be developed and used with confidence.

  5. Horizontal modular dry irradiated fuel storage system

    DOEpatents

    Fischer, Larry E.; McInnes, Ian D.; Massey, John V.

    1988-01-01

    A horizontal, modular, dry, irradiated fuel storage system (10) includes a thin-walled canister (12) for containing irradiated fuel assemblies (20), which canister (12) can be positioned in a transfer cask (14) and transported in a horizontal manner from a fuel storage pool (18), to an intermediate-term storage facility. The storage system (10) includes a plurality of dry storage modules (26) which accept the canister (12) from the transfer cask (14) and provide for appropriate shielding about the canister (12). Each module (26) also provides for air cooling of the canister (12) to remove the decay heat of the irradiated fuel assemblies (20). The modules (26) can be interlocked so that each module (26) gains additional shielding from the next adjacent module (26). Hydraulic rams (30) are provided for inserting and removing the canisters (12) from the modules (26).

  6. Status of food irradiation in the world

    NASA Astrophysics Data System (ADS)

    Kume, Tamikazu; Furuta, Masakazu; Todoriki, Setsuko; Uenoyama, Naoki; Kobayashi, Yasuhiko

    2009-03-01

    The status of food irradiation in the world in 2005 was investigated using published data, a questionnaire survey and direct visits. The results showed that the quantity of irradiated foods in the world in 2005 was 405,000 ton and comprised 1,86,000 ton (46%) for disinfection of spices and dry vegetables, 82,000 ton (20%) for disinfestation of grains and fruits, 32,000 ton (8%) for disinfection of meat and fish, 88,000 ton (22%) for sprout inhibition of garlic and potato, and 17,000 ton (4%) of other food items that included health foods, mushroom, honey, etc. Commercial food irradiation is increasing significantly in Asia, but decreasing in EU.

  7. Dosimetry procedures for an industrial irradiation plant

    NASA Astrophysics Data System (ADS)

    Grahn, Ch.

    Accurate and reliable dosimetry procedures constitute a very important part of process control and quality assurance at a radiation processing plant. γ-Dose measurements were made on the GBS 84 irradiator for food and other products on pallets or in containers. Chemical dosimeters wre exposed in the facility under conditions of the typical plant operation. The choice of the dosimeter systems employed was based on the experience in chemical dosimetry gained over several years. Dose uniformity information was obtained in air, spices, bulbs, feeds, cosmetics, plastics and surgical goods. Most products currently irradiated require dose uniformity which can be efficiently provided by pallet or box irradiators like GBS 84. The radiation performance characteristics and some dosimetry procedures are discussed.

  8. Enucleation versus plaque irradiation for choroidal melanoma

    SciTech Connect

    Straatsma, B.R.; Fine, S.L.; Earle, J.D.; Hawkins, B.S.; Diener-West, M.; McLaughlin, J.A.

    1988-07-01

    The Collaborative Ocular Melanoma Study (COMS) is an international, multicenter-controlled study. The organization includes an Executive Committee, Steering Committee, 6 Central Units, 32 Clinical Centers, and a Data and Safety Monitoring Committee. Scientifically, the COMS consists of (1) a randomized trial of patients with medium choroidal melanoma treated with enucleation versus iodine-125 plaque irradiation, (2) a randomized trial of patients with large choroidal melanoma treated with enucleation versus preenucleation external beam irradiation and enucleation, and (3) a prospective observational study of patients with small choroidal melanoma to determine whether a randomized trial of treatment is appropriate. In design and conduct of the COMS, special consideration is given to biostatistics and sample size considerations, iodine-125 plaque irradiation of choroidal melanoma, and coordinated ocular melanoma research. Recruitment is in progress. However, the pool of eligible patients is limited and the COMS needs the continued support and cooperation of ophthalmologists throughout the United States and Canada.

  9. Neutrophil myeloperoxidase destruction by ultraviolet irradiation

    SciTech Connect

    Hanker, J.; Giammara, B.; Strauss, G.

    1988-01-01

    The peroxidase activity of enriched leukocyte preparations on coverslips was determined cytochemically with a newly developed method. The techniques utilizes diaminobenzidine medium and cupric nitrate intensification and is suitable for analysis with light microscopy, SEM, and TEM. Blood specimens from control individuals were studied with and without in vitro UV irradiation and compared with those from psoriasis patients exposed therapeutically to various types of UV in phototherapy. All UV irradiated samples showed diminished neutrophil myeloperoxidase (MP) activity although that of the principal eosinophil peroxidase was unaffected. The SEMs supported the contention that decreased neutrophil MP activity might be related to UV induced degranulation. It is believed to be possible, eventually, to equate the observed MP degranulation effect after UV irradiation with diminished ability to fight bacterial infections.

  10. Effects of Laser Irradiation on Peripheral Nerve

    NASA Astrophysics Data System (ADS)

    Baxter, G. D.; Chow, R.; Armati, P.; Bjordal, J. M.; Laakso, L.

    2009-06-01

    A literature review was undertaken to determine the electrophysiological effects of Laser Irradiation (LI) on peripheral mammalian nerves, as a means of elucidating the potential mechanisms underlying pain relief associated with laser therapy. Relevant computerized databases and reference lists were searched, and experts consulted for further articles. A total of 38 studies, comprising 82 separate experiments were identified. In human studies, all types of LI (red and infrared, pulsed and cw) slowed nerve conduction velocity, and reduced compound action potential of irradiated nerves. In animal studies, infrared LI suppressed conduction velocity, as well as noxious stimulation evoked potential. This review thus indicates the potential of laser irradiation to inhibit activity in peripheral nerves, and highlights one potential mechanism of action for laser-mediated pain relief.

  11. Irradiated homologous costal cartilage for augmentation rhinoplasty

    SciTech Connect

    Lefkovits, G. )

    1990-10-01

    Although the ideal reconstructive material for augmentation rhinoplasty continues to challenge plastic surgeons, there exists no report in the literature that confines the use of irradiated homologous costal cartilage, first reported by Dingman and Grabb in 1961, to dorsal nasal augmentation. The purpose of this paper is to present a retrospective analysis of the author's experience using irradiated homologous costal cartilage in augmentation rhinoplasty. Twenty-seven dorsal nasal augmentations were performed in 24 patients between 16 and 49 years of age with a follow-up ranging from 1 to 27 months. Good-to-excellent results were achieved in 83.3% (20 of 24). Poor results requiring revision were found in 16.7% (4 of 24). Complication rates included 7.4% infection (2 of 27) and 14.8% warping (4 of 27). The resorption rate was zero. These results compare favorably with other forms of nasal augmentation. Advantages and disadvantages of irradiated homologous costal cartilage are discussed.

  12. Slow ion irradiation of sugar: astrobiological implications

    NASA Astrophysics Data System (ADS)

    Tuleta, M.; Gabla, L.; Wickramasinghe, N. C.

    2009-10-01

    As a result of irradiation by slow hydrogen and argon ions of saccharose, humic films having a fractal nature were produced. The use of hydrogen ions simulated roughly the interaction of low-energy solar wind protons with interplanetary dust grains which, in addition to organic and mineral dust, may include clumps of viable bacteria. The type of film generated by this experimental procedure could play a role in shielding the interior of micron-sized clumps from damaging ultraviolet and low-energy cosmic ray irradiation. We argue that such films may have played a role in processes that led to the initial origin of life, and following the emergence of life the same types of films (as, for instance, in biofilms surrounding cells) may have been modified by irradiation to offer protection to viable cells in the interior.

  13. Irradiation properties of T0 chopper components

    NASA Astrophysics Data System (ADS)

    Itoh, Shinichi; Ueno, Kenji; Ohkubo, Ryuji; Sagehashi, Hidenori; Funahashi, Yoshisato; Yokoo, Tetsuya

    2011-10-01

    We investigated the irradiation properties of the components of a T0 chopper. The organic materials in the rotor bearing grease, the magnetic fluids in seals, and the rubber in the timing belt, as well as the semiconductor materials in the rotation sensor and motor encoder, were all irradiated with high-energy γ-rays up to 100 kGy. No significant damage that shortens the lifetime of a T0 chopper was observed for the mechanical components. However, the semiconductor components were damaged by the irradiation. For the rotation sensor system detecting the rotor phase, the signal from a marker on the rotor shaft was transmitted outside the shielding by an optical fiber with radiation-proofing and the electrical circuits were removed from the beamline shielding. The lifetime of the motor encoder possibly meets the requirement for the maintenance period of the T0 chopper.

  14. Health risk assessment of irradiated topaz

    SciTech Connect

    Nelson, J.W.; Baum, J.W.

    1993-01-01

    Irradiated topaz gemstones are currently processed for color improvement by subjecting clear stones to neutron or high-energy electron irradiations, which leads to activation of trace elements in the stones. Assessment of the risk to consumers required the identification and quantification of the resultant radionuclides and the attendant exposure. Representative stones from Brazil, India, Nigeria, Sri Lanka were irradiated and analyzed for gamma ray and beta particle emissions, using sodium iodide and germanium spectrometers; and Geiger-Muller, plastic and liquid scintillation, autoradiography, and thermoluminescent-dosimetry measurement techniques. Based on these studies and other information derived from published literature, dose and related risk estimates were made for typical user conditions. New criteria and methods for routine assays for acceptable release, based on gross beta and gross photon emissions from the stones, were also developed.

  15. BPX insulation irradiation program test results

    SciTech Connect

    McManamy, T.J. ); Kanemoto, G. ); Snook, P.G. . Plasma Physics Lab.)

    1991-01-01

    The toroidal field coil insulation for the Burning Plasma Experiment (BPX) is expected to receive a radiation dose of nearly 10{sup 10} rad and to withstand significant mechanical stresses. An irradiation test program was performed at the Idaho National Engineering Laboratory (INEL) using the Advanced Technology Reactor (ATR) for irradiations to doses on the order of 3 {times} 10{sup 10} rad. The flexure and shear strength with compression of commercially procured sheet material were reported earlier. A second series of tests has been performed to slightly higher dose levels with vacuum impregnated materials, glass strand material, and Spaulrad-S sheet samples. Vacuum impregnation with a Shell 9405 resin and 9470 hardener was used to produce bonded copper squares and flexure samples of both pure resin and resin with S-glass. A new test fixture was developed to test the bonded samples in shear without applied compression. The Spaulrad-S flexure samples demonstrated a loss of strength with irradiation, similar to previous results. The pure resin lost nearly all flexibility, while the S-glass-reinforced samples retained between 30% and 40% of the initial flexure strength. The S-glass strands showed a 30% loss of strength at the higher dose level when tested in tension. The bonded copper squares had a low room-temperature shear strength of approximately 17 MPa before irradiation, which was unchanged in the irradiated samples. Shear testing of unirradiated bonded copper squares with ten different types of surface treatment revealed that the low shear strength resulted from the polyurethane primer used. In the later series of test, the epoxy-based primers and DZ-80 from Ciba-Geigy did much better, with shear strengths on the order of 40 MPa. These samples also demonstrated a resistance to cryogenic shock. One irradiated bonded sample was tested up 10 210 MPa in compression, the limit of the test fixture, without failure.

  16. Studies on potato irradiation in the G.D.R.

    NASA Astrophysics Data System (ADS)

    Luther, Th.; Hübner, G.; Grahn, Ch.; Döllstädt, R.

    The studies of potato irradiation have been conducted in the framework of the National Food Irradiation Research Project for 4 years. Although in the G.D.R. the use of chemical sprout inhibitors is allowed, potato irradiation can be an alternative technique for potato processing. Before irradiation a wound healing period of approx. 2 weeks is absolutely necessary to protect the potatoes from Fusarium. The method that presents the minimum risk of damage is irradiation in containers. Economic evaluations for the irradiation of potatoes are also made.

  17. [Pelvic irradiation in prostate cancer: what place for what volumes?].

    PubMed

    Chapet, O; Enachescu, C; Lorchel, F

    2013-10-01

    External beam radiotherapy alone is a standard treatment for prostate cancer. According to clinical, histological and biological characteristics of the tumour, lymph node irradiation can be done in combination with irradiation of the prostate. The completion of pelvic irradiation remains controversial and may cause complications by increasing volumes of irradiated healthy tissues. The accuracy of the delineation of lymph node becomes an important issue. This article proposes to take on the characteristics of the pelvic lymph node drainage of the prostate, to review the literature on pelvic irradiation and the definition of volumes to be irradiated.

  18. Enhancement of Irradiation Capability of the Experimental Fast Reactor Joyo

    NASA Astrophysics Data System (ADS)

    Maeda, Shigetaka; Serine, Takashi; Aoyama, Takafumi; Suzuki, Soju

    2009-08-01

    The experimental fast reactor Joyo is the first sodium-cooled fast reactor in Japan. One of its primary missions is to perform irradiation tests of fuel and structural materials to support the development of fast reactors. The MK-III high performance core upgrade to enhance the irradiation testing capabilities was completed in 2003. In order to expand Joyo's capabilities for innovative irradiation testing applications, neutron spectrum tailoring, lower irradiation temperature, movable sample devices and fast neutron beam holes are being considered. This program responds to existing irradiation needs and aims to further expand capabilities for a variety of irradiation tests.

  19. Electron irradiation of modern solar cells

    NASA Technical Reports Server (NTRS)

    Anspaugh, B. E.; Miyahira, T. F.

    1977-01-01

    A number of modern solar cell types representing 1976 technology (as well as some older types) were irradiated with 1 MeV electrons (and a limited number with 2 MeV electrons and 10 MeV protons). After irradiation, the cells were annealed, with I-V curves measured under AMO at 30 C. The purpose was to provide data to be incorporated in the revision of the solar cell radiation handbook. Cell resistivities ranged from 2 to 20 ohm-cm, and cell thickness from 0.05 to 0.46 mm. Cell types examined were conventional, shallow junction, back surface field (BSF), textured, and textured with BSF.

  20. Quantum dot intermixing using excimer laser irradiation

    SciTech Connect

    Djie, H. S.; Ooi, B. S; Gunawan, O.

    2006-08-21

    The authors report a spatial control of the band gap in InGaAs/GaAs quantum dots (QDs) using the combined effects of pulsed excimer laser irradiation and impurity-free dielectric cap induced intermixing technique. A large band gap shift of up to 180 meV has been obtained under laser irradiation of 480 mJ/cm{sup 2} and 150 pulses to the SiO{sub 2} capped shallow QD structure, while the nonirradiated SiO{sub 2} and Si{sub x}N{sub y} capped QDs only exhibit band gap shifts of 18 and 91 meV, respectively.

  1. Schistosoma mansoni: cercarial responses to irradiance changes

    SciTech Connect

    Saladin, K.S.

    1982-02-01

    Cercariae of Schistosoma mansoni alternate between active swimming and passive drifting. They began swimming in response to either an increase or decrease in irradiance experienced during the passive phase. The number of cercariae reacting to a shadow was proportional to the magnitude of the stimulus. The shadow response may be mediated by the cercaria's ciliary receptors. About half as many cercariae reacted to an irradiance increase as to an equivalent decrease. This report is the first quantitative study of photosensory stimulus-response relationships in schistosome cercariae.

  2. Vanadium irradiation at ATR - neutronics aspects

    SciTech Connect

    Gomes, I.C.; Smith, D.L.

    1995-04-01

    Calculations were performed to estimate damage and transmutation rates in vanadium irradiated in the ATR (Advanced Test Reactor) located in Idaho. The main focuses of the study are to evaluate the transmutation of vanadium to chromium and to explore ways to design the irradiation experiment to avoid excessive transmutation. It was found that the A-hole of ATR produces damage rate of {approximately} 0.2%/dpa of vanadium to chromium. A thermal neutron filter can be incorporated into the design to reduce the vanadium-to-chromium transmutation rate to low levels. A filter 1-2 mm thick of gadolinium or hafnium can be used.

  3. Separation of sodium-22 from irradiated targets

    DOEpatents

    Taylor, Wayne A.; Jamriska, David

    1996-01-01

    A process for selective separation of sodium-22 from an irradiated target including dissolving an irradiated target to form a first solution, contacting the first solution with hydrated antimony pentoxide to selectively separate sodium-22 from the first solution, separating the hydrated antimony pentoxide including the separated sodium-22 from the first solution, dissolving the hydrated antimony pentoxide including the separated sodium-22 in a mineral acid to form a second solution, and, separating the antimony from the sodium-22 in the second solution.

  4. Effects of gamma irradiation on deteriorated paper

    NASA Astrophysics Data System (ADS)

    Bicchieri, Marina; Monti, Michela; Piantanida, Giovanna; Sodo, Armida

    2016-08-01

    Even though gamma radiation application, also at the minimum dosage required for disinfection, causes depolymerization and degradation of the paper substrate, recently published papers seemed, instead, to suggest that γ-rays application could be envisaged in some conditions for Cultural Heritage original documents and books. In some of the published papers, the possible application of γ-rays was evaluated mainly by using mechanical tests that scarcely reflect the chemical modifications induced in the cellulosic support. In the present article the effect of low dosage γ-irradiation on cellulosic substrates was studied and monitored applying different techniques: colorimetry, spectroscopic measurements, carbonyl content and average viscometric degree of polymerization. Two different papers were investigated, a non-sized, non-filled cotton paper, and a commercial permanent paper. To simulate a real deteriorated document, which could need γ-rays irradiation, some samples were submitted to a hydrolysis treatment. We developed a treatment based on the exposition of paper to hydrochloric acid vapors, avoiding any contact of the samples with water. This method induces a degradation similar to that observed on original documents. The samples were then irradiated with 3 kGy γ-rays at a 5258 Gy/h rate. The aforementioned analyses were performed on the samples just irradiated and after artificial ageing. All tests showed negative effects of gamma irradiation on paper. Non-irradiated paper preserves better its appearance and chemical properties both in the short term and after ageing, while the irradiated samples show appreciable color change and higher oxidation extent. Since the Istituto centrale restauro e conservazione patrimonio archivistico e librario is responsible for the choice of all restoration treatments that could be applied on library and archival materials under the protection of the Italian State (http://www.icpal.beniculturali.it/allegati/DM-7

  5. Bonding of dopants to irradiated polymers

    NASA Astrophysics Data System (ADS)

    Fink, D.; Klett, R.; Hnatowicz, V.; Vacik, J.; Mathis, C.; Omichi, H.; Hosoi, F.; Chadderton, L. T.; Wang, L.

    1996-08-01

    Latent tracks are formed in polyimide, polypropylene and polyethylene by irradiation with 0.5 to 3 GeV heavy ions. They are then doped with aqueous LiCl, organo- {Li}/{THF}, or {C60}/{THF} solutions for well-defined periods after the irradiation. Subsequently, the excess of non-trapped Li dopant fraction is washed out. The remaining lithium-doped polymer zones along the latent ion tracks are studied here. The depth distribution of the bonding efficiency, as determined by neutron depth profiling, points out an electronic nature of the bonding process.

  6. Irradiated versus fumigated spices in sausage.

    PubMed

    Bolander, C R; Toma, R B; Davis, R M; Medora, N P

    1995-11-01

    The efficacy of gamma radiation and ethylene oxide fumigation as decontaminating treatments for spices used in sausages was compared. Microbial loads of sausages containing irradiated, fumigated or non-treated spices were examined over three intervals of time. No significant differences between microbial loads of Mexican sausages containing irradiated spices (10 kGy) verses ethylene oxide-treated spices were found. Mexican sausages containing treated spices had significantly lower yeast, mould and spore counts than control sausages. After 8 weeks of storage, only the microbial loads of control sausages suggested spoilage. No discernable differences in treatment efficacy were noted with respect to yeast, mould and spore counts in Italian sausages.

  7. Neutron Spectrum Measurements from Irradiations at NCERC

    SciTech Connect

    Jackman, Kevin Richard; Mosby, Michelle A.; Bredeweg, Todd Allen; Hutchens, Gregory Joe; White, Morgan Curtis

    2015-04-15

    Several irradiations have been conducted on assemblies (COMET/ZEUS and Flattop) at the National Criticality Experiments Research Center (NCERC) located at the Nevada National Security Site (NNSS). Configurations of the assemblies and irradiated materials changed between experiments. Different metallic foils were analyzed using the radioactivation method by gamma-ray spectrometry to understand/characterize the neutron spectra. Results of MCNP calculations are shown. It was concluded that MCNP simulated spectra agree with experimental measurements, with the caveats that some data are limited by statistics at low-energies and some activation foils have low activities.

  8. The effects of sunspots on solar irradiance

    NASA Technical Reports Server (NTRS)

    Hudson, H. S.; Silva, S.; Woodard, M.; Willson, R. C.

    1982-01-01

    It is pointed out that the darkness of a sunspot on the visible hemisphere of the sun will reduce the solar irradiance on the earth. Approaches are discussed for obtaining a crude estimate of the irradiance deficit produced by sunspots and of the total luminosity reduction for the whole global population of sunspots. Attention is given to a photometric sunspot index, a global measure of spot flux deficit, and models for the compensating flux excess. A model is shown for extrapolating visible-hemisphere spot areas to the invisible hemisphere. As an illustration, this extrapolation is used to calculate a very simple model for the reradiation necessary to balance the flux deficit.

  9. Irradiation of meat products, chicken and use of irradiated spices for sausages

    NASA Astrophysics Data System (ADS)

    Kiss, I. F.; Beczner, J.; Zachariev, Gy.; Kovács, S.

    The shelf-life of packed minced meat has been increased at least threefold at 4°C by applying a 2 kGy dose. Results have been confirmed by detailed quatitative microbiological examinations. Sensory evaluations show no significant difference between the unirradiated samples. The optimal average dose was 4 kGy for packed-frosen chicken. The number of mesophilic aerobic microbes was reduced by 2, that of psychrotolerant by 2-3 and that of Enterbacteriaceae by 3-4 orders of magnitude by 4 kGy. S. aureus and Salmonella could not be detected in the irradiated samples. In sensory evaluations there was no significant difference between untreated and irradiated samples. In 1984-1985 5100 kg irradiated chickens were marketed labelled as radiation treated. Irradiated spices (5 kGy) were used in the production of sausages (heat-treated and non-heat-treated) under industrial conditions. The microbiological contamination of irradiated spices was lower than that of ethylene oxide treated ones. The cell count in products made with irradiated spices was lower than in those made with unirradiated spices. The sausages proved to be of very good quality. In accordance with the permission, products were marketed and because of the low ratio of spices there was no need to declare them as using irradiated spices.

  10. Determination of irradiation dose and distinguishing between irradiated and non irradiated fish meat by real-time PCR.

    PubMed

    Şakalar, Ergün; Mol, Sühendan

    2015-09-01

    In this study, the effects of gamma irradiation on the DNA of fish (Oncorhynchus mykiss) by real-time PCR were studied. Fish (O. mykiss) were exposed to radiation doses of 0.250, 0.500, 1, 3, 5, 7, and 9 kGy in a gamma cell. Primers were designed for regions with different lengths of both nuclear and mitochondrial DNA, and each primer was used to amplify the DNA from irradiated samples. The amplicon curves for mitochondrial and nuclear DNA, and the correlations among the curves, were obtained. The Ct values for a 519 bp region of the 18S RNA gene on nuclear DNA correlated appropriately. Radiation doses applied to the fillets were estimated using the standard curve data obtained from the correlation values, and the DNA damage caused by each dose was calculated. As a consequence, a molecular methodology to analyze irradiated fish meat qualitatively and also for the estimation of administered dose was developed. This method allowed analysis of irradiated fish, which had been stored for up to 3 months with a dose limit of approximately 0.5 kGy.

  11. Understanding the Irradiation Behavior of Zirconium Carbide

    SciTech Connect

    Motta, Arthur; Sridharan, Kumar; Morgan, Dane; Szlufarska, Izabela

    2013-10-11

    Zirconium carbide (ZrC) is being considered for utilization in high-temperature gas-cooled reactor fuels in deep-burn TRISO fuel. Zirconium carbide possesses a cubic B1-type crystal structure with a high melting point, exceptional hardness, and good thermal and electrical conductivities. The use of ZrC as part of the TRISO fuel requires a thorough understanding of its irradiation response. However, the radiation effects on ZrC are still poorly understood. The majority of the existing research is focused on the radiation damage phenomena at higher temperatures (>450{degree}C) where many fundamental aspects of defect production and kinetics cannot be easily distinguished. Little is known about basic defect formation, clustering, and evolution of ZrC under irradiation, although some atomistic simulation and phenomenological studies have been performed. Such detailed information is needed to construct a model describing the microstructural evolution in fast-neutron irradiated materials that will be of great technological importance for the development of ZrC-based fuel. The goal of the proposed project is to gain fundamental understanding of the radiation-induced defect formation in zirconium carbide and irradiation response by using a combination of state-of-the-art experimental methods and atomistic modeling. This project will combine (1) in situ ion irradiation at a specialized facility at a national laboratory, (2) controlled temperature proton irradiation on bulk samples, and (3) atomistic modeling to gain a fundamental understanding of defect formation in ZrC. The proposed project will cover the irradiation temperatures from cryogenic temperature to as high as 800{degree}C, and dose ranges from 0.1 to 100 dpa. The examination of this wide range of temperatures and doses allows us to obtain an experimental data set that can be effectively used to exercise and benchmark the computer calculations of defect properties. Combining the examination of radiation

  12. Polymer Morphological Change Induced by Terahertz Irradiation

    PubMed Central

    Hoshina, Hiromichi; Suzuki, Hal; Otani, Chiko; Nagai, Masaya; Kawase, Keigo; Irizawa, Akinori; Isoyama, Goro

    2016-01-01

    As terahertz (THz) frequencies correspond to those of the intermolecular vibrational modes in a polymer, intense THz wave irradiation affects the macromolecular polymorph, which determines the polymer properties and functions. THz photon energy is quite low compared to the covalent bond energy; therefore, conformational changes can be induced “softly,” without damaging the chemical structures. Here, we irradiate a poly(3-hydroxybutylate) (PHB) / chloroform solution during solvent casting crystallization using a THz wave generated by a free electron laser (FEL). Morphological observation shows the formation of micrometer-sized crystals in response to the THz wave irradiation. Further, a 10−20% increase in crystallinity is observed through analysis of the infrared (IR) absorption spectra. The peak power density of the irradiating THz wave is 40 MW/cm2, which is significantly lower than the typical laser intensities used for material manipulation. We demonstrate for the first time that the THz wave effectively induces the intermolecular rearrangement of polymer macromolecules. PMID:27272984

  13. Minimizing material damage using low temperature irradiation

    NASA Astrophysics Data System (ADS)

    Craven, E.; Hasanain, F.; Winters, M.

    2012-08-01

    Scientific advancements in healthcare driven both by technological breakthroughs and an aging and increasingly obese population have lead to a changing medical device market. Complex products and devices are being developed to meet the demands of leading edge medical procedures. Specialized materials in these medical devices, including pharmaceuticals and biologics as well as exotic polymers present a challenge for radiation sterilization as many of these components cannot withstand conventional irradiation methods. The irradiation of materials at dry ice temperatures has emerged as a technique that can be used to decrease the radiation sensitivity of materials. The purpose of this study is to examine the effect of low temperature irradiation on a variety of polymer materials, and over a range of temperatures from 0 °C down to -80 °C. The effectiveness of microbial kill is also investigated under each of these conditions. The results of the study show that the effect of low temperature irradiation is material dependent and can alter the balance between crosslinking and chain scission of the polymer. Low temperatures also increase the dose required to achieve an equivalent microbiological kill, therefore dose setting exercises must be performed under the environmental conditions of use.

  14. 10 CFR 36.33 - Irradiator pools.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... purification system designed to be capable of maintaining the water during normal operation at a conductivity..., irradiator pools must either: (1) Have a water-tight stainless steel liner or a liner metallurgically... water level that could allow water to drain out of the pool. Pipes that have intakes more than 0.5...

  15. Monitoring pathogens from irradiated agriculture products

    NASA Astrophysics Data System (ADS)

    Butterweck, Joseph S.

    The final food and environmental safety assessment of agriculture product irradiation can only be determined by product history. Product history will be used for future research and development, regulations, commercial practices and implementation of agriculture and food irradiation on a regional basis. The commercial irradiator treats large varieties and amounts of products that are used in various environments. It, in time, will generate a large data base of product history. Field product monitoring begins when food irradiation progresses from the pilot/demonstration phase to the commercial phase. At that time, it is important that there be in place a monitoring system to collect and analyze field data. The systems managers, public health authorities and exotic disease specialists will use this information to assess the reduction of food pathogens on the populace and the environment. The common sources of monitoring data are as follows: 1) Host Monitoring a) Medical Diagnosis b) Autopsy c) Serology Surveys 2) Environmental Monitoring a) Sentinel b) Pest Surveys/Microbial Counts c) Sanitary Inspections 3) Food Industries Quality Assurance Monitoring a) End Product Inspection b) Complaints c) Continual Use of the Product

  16. Amphytrion: Example of a high capacity irradiator

    NASA Astrophysics Data System (ADS)

    Keraron(SGN-France), Y.; Santos(Amphytrion-France), P. L.

    SGN recently built a pallet irradiator for the AMPHYTRION Company which incorporates new technological features. After a short review of the design criteria, the major mechanical equipment is described (source-holder, conveyor, automatic warehouse system), together with the ventilation/air conditioning system and the control/management architecture. Information is given on the new technical aspects and the performance of the facility.

  17. Microwave Irradiation on Halloysite-Polypropylene Nanocomposites

    NASA Astrophysics Data System (ADS)

    Espino, Omar; Yust, Brian; Chipara, Dorina; Ajayan, Pullickel; Chipara, Alin; Chipara, Mircea; Utrgv Collaboration; Rice Collaboration

    Halloysite is an unique cyllindrical nanoclay characterized by poor electrical and thermal conductivity, which may become the filler of choice for the reinforcement of polymeric matrix, where electrical or thermal insulation are required. The main limits in the use of halloysite as replacement for carbon nanotube (CNT) are: 1. Smaller aspect ratio as halloysites are typically shorter than CNTs. 2. Smaller Young modulus of halloysites compared with CNTs. 3. Reduced thermal stability due to the loss of water upon heating. A research on halloysite dispersed within isotactic polypropylene is reported. To improve the interface between the halloysite and the polymeric matrix a microwave irradiation step has been considered. The local heating of the halloysite nanotubes is mediated by the absorbed/structural water content of the nanoclay. Nanocomposites loaded by various amounts of halloysite ranging from 0 % to 20 % wt. have been prepared by melt mixing by using a Haake RheoMixer. The as obtained nanocomposites have been subjected to microwave irradiation at 75 W in an Anton Paar Monowave 300 system and various irradiation times ranging from 5, 10, 15, 30, 45, and 60 minutes. The effect of microwave irradiation has been studied by Raman and FTIR spectroscopy

  18. Studies of Solar EUV Irradiance from SOHO

    NASA Technical Reports Server (NTRS)

    Floyd, Linton

    2002-01-01

    The Extreme Ultraviolet (EUV) irradiance central and first order channel time series (COC and FOC) from the Solar EUV Monitor aboard the Solar and Heliospheric observatory (SOHO) issued in early 2002 covering the time period 1/1/96-31/1201 were analyzed in terms of other solar measurements and indices. A significant solar proton effect in the first order irradiance was found and characterized. When this effect is removed, the two irradiance time series are almost perfectly correlated. Earlier studies have shown good correlation between the FOC and the Hall core-to-wing ratio and likewise, it was the strongest component of the COC. Analysis of the FOC showed dependence on the F10.7 radio flux. Analysis of the CDC signals showed additional dependences on F10.7 and the GOES x-ray fluxes. The SEM FOC was also well correlated with thein 30.4 nm channel of the SOHO EUV Imaging Telescope (EIT). The irradiance derived from all four EIT channels (30.4 nm, 17.1 nm, 28.4 nm, and 19.5 nm) showed better correlation with MgII than F10.7.

  19. 10 CFR 36.33 - Irradiator pools.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... purification system designed to be capable of maintaining the water during normal operation at a conductivity..., irradiator pools must either: (1) Have a water-tight stainless steel liner or a liner metallurgically... water level that could allow water to drain out of the pool. Pipes that have intakes more than 0.5...

  20. 10 CFR 36.33 - Irradiator pools.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... purification system designed to be capable of maintaining the water during normal operation at a conductivity..., irradiator pools must either: (1) Have a water-tight stainless steel liner or a liner metallurgically... water level that could allow water to drain out of the pool. Pipes that have intakes more than 0.5...

  1. 10 CFR 36.33 - Irradiator pools.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... purification system designed to be capable of maintaining the water during normal operation at a conductivity..., irradiator pools must either: (1) Have a water-tight stainless steel liner or a liner metallurgically... water level that could allow water to drain out of the pool. Pipes that have intakes more than 0.5...

  2. 10 CFR 36.33 - Irradiator pools.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... purification system designed to be capable of maintaining the water during normal operation at a conductivity..., irradiator pools must either: (1) Have a water-tight stainless steel liner or a liner metallurgically... water level that could allow water to drain out of the pool. Pipes that have intakes more than 0.5...

  3. Fluorescence anisotropy of UV-irradiated viruses.

    PubMed

    Hörer, O L

    1989-01-01

    The steady-state fluorescence anisotropy measurements on influenza and parainfluenza viruses, showed no changes in the microviscosity of the viral membranes after exposure to UV-irradiation, when a fluorescent probe was used, but the intrinsic fluorescence of viral proteins presented, under the same experimental conditions, a significant difference of anisotropy behaviour in the two viruses used.

  4. SOLVENT FREE CHEMICAL TRANSFORMATION USING MICROWAVE IRRADIATION

    EPA Science Inventory

    Microwave-expedited solvent-free synthetic processes will be described that involve the exposure of neat reactants to microwave (MW) irradiation in the presence of supported reagents or catalysts on mineral oxides. Recent developments will be presented on the synthetic utility o...

  5. Sucrose synthesis in gamma irradiated sweet potato

    SciTech Connect

    Ailouni, S.; Hamdy, M.K.; Toledo, R.T.

    1987-01-01

    Effect of ..cap alpha..-irradiation carbohydrate metabolism was examined to elucidate mechanism of sucrose accumulation in sweet potato (SP). Enzymes examined were: ..beta..-amylase, phosphorylase, phosphoglucomutase, phosphoglucose isomerase, sucrose phosphate synthetase and sucrose synthetase. Irradiated SP (Red Jewell) sucrose was synthesized to yield 10.7% after 4 d PI. Activities of sugar synthesizing enzymes in irradiated SP were enhanced to different degrees using 100-200 Krad and 3 d PI at 24/sup 0/C. Phosphorylase and phosphoglucomutases specific activities reached 2.4 and 1.8 folds, respectively compared to control SP. ..beta..-amylase, phosphoglucose isomerase, sucrose synthetase and sucrose phosphate synthetase were also affected to yield 1.2, 1.3, 1.3 and 1.2 folds, respectively compared to controls. It is believed that amylase hydrolyzed starch to glucose which is converted to fructose by phosphoglucose isomerase. Sucrose is then formed by sucrose phosphate synthetase and/or sucrose synthetase leading to its accumulation. The irradiated SP was used for alcohol fermentation leading to 500 gal. of 200 proof ethanol/acre (from 500-600 bushels tuber/acre).

  6. Localized comedo formation after cobalt irradiation

    SciTech Connect

    Myskowski, P.L.; Safai, B.

    1981-10-01

    Following Cobalt-60 irradiation for a left frontotemporal tumor, a 61-year-old woman developed comedones on the forehead. These changes responded to conventional acne therapy with retinoic acid. Multiple acneigenic factors were implicated in the pathogenesis of her lesions.

  7. Hyperparathyroidism After Irradiation for Childhood Malignancy

    SciTech Connect

    McMullen, Todd; Bodie, Greg; Gill, Anthony; Ihre-Lundgren, Catharina; Shun, Albert; Bergin, Mary; Stevens, Graham; Delbridge, Leigh

    2009-03-15

    Purpose: To examine the occurrence of hyperparathyroidism in a cohort of patients undergoing combined parathyroid and thyroid surgery after previous head-and-neck irradiation for childhood malignancy. Methods and Materials: This is a retrospective cohort study for the years 1996 to 2007. The study group comprised patients undergoing surgery in University of Sydney Endocrine Surgical Unit who had received previous head-and-neck irradiation in childhood and who were identified as having pathologic thyroid and parathyroid characteristics. Results: A total of 53 patients were identified in whom head-and-neck irradiation for the treatment of childhood malignancy had been documented. In each of the cases, thyroid disease was the primary reason for referral for surgery. Five of these patients (10%) were found to exhibit coexisting hyperparathyroidism. The latency period for hyperparathyroidism was less than 20 years in 4 of the 5 cases. There were four conventional parathyroid adenomas and one parathyroid lipoadenoma. All patients exhibited a significant decrease in postoperative calcium levels after surgery. Conclusions: To our knowledge, this is the first study to document the significant risk of hyperparathyroidism after radiation exposure for childhood malignancy. The timeframe for development of disease is much shorter than that published for individuals who have undergone irradiation for benign diseases. High doses of therapeutic radiation at a young age make childhood survivors of malignancy at especially high risk for developing hyperparathyroidism.

  8. New pallet irradiation for Gammaster International

    NASA Astrophysics Data System (ADS)

    Möhlmann, Mr. J. H. F.

    1993-07-01

    State of the art technology offers many opportunities to improve production process with ionizing radiation. Also the requirements to this process become more and more stringent; who was aware of the ISO-9000 Standards? Now it is a necessary concept? Internal and external audits, in particular by Regulatory Bodies such as the FDA and DHSS/MCA, are necessary and commonplace requirements when operating in the Healthcare and Pharmaceutical sectors. Efficiency is a major requirement for industry and also for our radiation business. With all the above mentioned items in mind, Gammaster International B.V. in close cooperation with Nordion International Inc. has developed and built a new type Pallet Irradiator. In this new concept, our 22 years experience in gamma processing and the expertise gained in 10 years of operation of pallet irradiators was incorporated. For this irradiator Gammaster International designed and built a new process control console, incorporating state of the art technology such as: - A well-balanced safety system - A control panel, with status indication for all essential operating and safety parameters - Advances warning for necessary maintenance work - Automatic timer-setting control in addition to an automatic timer setting modification - Clear indication of the position of the product inside the unit and its status - Fully automatic product information generated when the product leaves the irradiation unit - Visual process control with the help of a color monitor - Incremental dose-control - Fault identification

  9. Continuous wave laser irradiation of explosives

    SciTech Connect

    McGrane, Shawn D.; Moore, David S.

    2010-12-01

    Quantitative measurements of the levels of continuous wave (CW) laser light that can be safely applied to bare explosives during contact operations were obtained at 532 nm, 785 nm, and 1550 nm wavelengths. A thermal camera was used to record the temperature of explosive pressed pellets and single crystals while they were irradiated using a measured laser power and laser spot size. A visible light image of the sample surface was obtained before and after the laser irradiation. Laser irradiation thresholds were obtained for the onset of any visible change to the explosive sample and for the onset of any visible chemical reaction. Deflagration to detonation transitions were not observed using any of these CW laser wavelengths on single crystals or pressed pellets in the unconfined geometry tested. Except for the photochemistry of DAAF, TATB and PBX 9502, all reactions appeared to be thermal using a 532 nm wavelength laser. For a 1550 nm wavelength laser, no photochemistry was evident, but the laser power thresholds for thermal damage in some of the materials were significantly lower than for the 532 nm laser wavelength. No reactions were observed in any of the studied explosives using the available 300 mW laser at 785 nm wavelength. Tables of laser irradiance damage and reaction thresholds are presented for pressed pellets of PBX9501, PBX9502, Composition B, HMX, TATB, RDX, DAAF, PETN, and TNT and single crystals of RDX, HMX, and PETN for each of the laser wavelengths.

  10. Polymer Morphological Change Induced by Terahertz Irradiation

    NASA Astrophysics Data System (ADS)

    Hoshina, Hiromichi; Suzuki, Hal; Otani, Chiko; Nagai, Masaya; Kawase, Keigo; Irizawa, Akinori; Isoyama, Goro

    2016-06-01

    As terahertz (THz) frequencies correspond to those of the intermolecular vibrational modes in a polymer, intense THz wave irradiation affects the macromolecular polymorph, which determines the polymer properties and functions. THz photon energy is quite low compared to the covalent bond energy; therefore, conformational changes can be induced “softly,” without damaging the chemical structures. Here, we irradiate a poly(3-hydroxybutylate) (PHB) / chloroform solution during solvent casting crystallization using a THz wave generated by a free electron laser (FEL). Morphological observation shows the formation of micrometer-sized crystals in response to the THz wave irradiation. Further, a 10‑20% increase in crystallinity is observed through analysis of the infrared (IR) absorption spectra. The peak power density of the irradiating THz wave is 40 MW/cm2, which is significantly lower than the typical laser intensities used for material manipulation. We demonstrate for the first time that the THz wave effectively induces the intermolecular rearrangement of polymer macromolecules.

  11. X-ray irradiation of yeast cells

    NASA Astrophysics Data System (ADS)

    Masini, Alessandra; Batani, Dimitri; Previdi, Fabio; Conti, Aldo; Pisani, Francesca; Botto, Cesare; Bortolotto, Fulvia; Torsiello, Flavia; Turcu, I. C. Edmond; Allott, Ric M.; Lisi, Nicola; Milani, Marziale; Costato, Michele; Pozzi, Achille; Koenig, Michel

    1997-10-01

    Saccharomyces Cerevisiae yeast cells were irradiated using the soft X-ray laser-plasma source at Rutherford Laboratory. The aim was to produce a selective damage of enzyme metabolic activity at the wall and membrane level (responsible for fermentation) without interfering with respiration (taking place in mitochondria) and with nuclear and DNA activity. The source was calibrated by PIN diodes and X-ray spectrometers. Teflon stripes were chosen as targets for the UV laser, emitting X-rays at about 0.9 keV, characterized by a very large decay exponent in biological matter. X-ray doses to the different cell compartments were calculated following a Lambert-Bouguet-Beer law. After irradiation, the selective damage to metabolic activity at the membrane level was measured by monitoring CO2 production with pressure silicon detectors. Preliminary results gave evidence of pressure reduction for irradiated samples and non-linear response to doses. Also metabolic oscillations were evidenced in cell suspensions and it was shown that X-ray irradiation changed the oscillation frequency.

  12. Nanoscale Morphology Evolution Under Ion Irradiation

    SciTech Connect

    Aziz, Michael J.

    2014-11-10

    We showed that the half-century-old paradigm of morphological instability under irradiation due to the curvature-dependence of the sputter yield, can account neither for the phase diagram nor the amplification or decay rates that we measure in the simplest possible experimental system -- an elemental semiconductor with an amorphous surface under noble-gas ion irradiation; We showed that a model of pattern formation based on the impact-induced redistribution of atoms that do not get sputtered away explains our experimental observations; We developed a first-principles, parameter-free approach for predicting morphology evolution, starting with molecular dynamics simulations of single ion impacts, lasting picoseconds, and upscaling through a rigorous crater-function formalism to develop a partial differential equation that predicts morphology evolution on time scales more than twelve orders of magnitude longer than can be covered by the molecular dynamics; We performed the first quantitative comparison of the contributions to morphological instability from sputter removal and from impact-induced redistribution of atoms that are removed, and showed that the former is negligible compared to the latter; We established a new paradigm for impact-induced morphology evolution based on crater functions that incorporate both redistribution and sputter effects; and We developed a model of nanopore closure by irradiation-induced stress and irradiationenhanced fluidity, for the near-surface irradiation regime in which nuclear stopping predominates, and showed that it explains many aspects of pore closure kinetics that we measure experimentally.

  13. Irradiation Processing Department monthly report, June 1962

    SciTech Connect

    Not Available

    1992-07-13

    This document details activities of the Irradiation Processing Department during the month of June, 1962. A general summary is included at the start of the report, after which the report is divided into the following sections: Research and Engineering Operations; Production and Reactor Operations; Facilities Engineering Operation; and NPR Project.

  14. High accuracy diffuse horizontal irradiance measurements without a shadowband

    SciTech Connect

    Schlemmer, J.A; Michalsky, J.J.

    1995-12-31

    The standard method for measuring diffuse horizontal irradiance uses a fixed shadowband to block direct solar radiation. This method requires a correction for the excess skylight blocked by the band, and this correction varies with sky conditions. Alternately, diffuse horizontal irradiance may be calculated from total horizontal and direct normal irradiance. This method is in error because of angular (cosine) response of the total horizontal pyranometer to direct beam irradiance. This paper describes an improved calculation of diffuse horizontal irradiance from total horizontal and direct normal irradiance using a predetermination of the angular response of the total horizontal pyranometer. We compare these diffuse horizontal irradiance calculations with measurements made with a shading-disk pyranometer that shields direct irradiance using a tracking disk. Results indicate significant improvement in most cases. Remaining disagreement most likely arises from undetected tracking errors and instrument leveling.

  15. Food irradiation: Standards, regulations and world-wide trade

    NASA Astrophysics Data System (ADS)

    Roberts, Peter B.

    2016-12-01

    There is an established framework of international standards for food irradiation covering human health, plant protection, labelling, dose delivery, quality assurance and facility management. Approximately 60 countries permit irradiation of one or more food or food classes. National regulations are briefly reviewed. Decontamination of spices, herbs and condiments remains the single largest application of irradiation. However, in recent years the market for irradiated fresh and processed meat has become firmly established in several countries including China and the USA. At least 10 countries have recently established bi-lateral agreements for trade in irradiated fresh fruits and vegetables using phytosanitary irradiation. Irradiated fresh produce volumes now exceed 20,000 t per year. Rationalization and greater consistency in labelling regulations would be advantageous to the future growth of applications of food irradiation.

  16. Neutron irradiation of Am-241 effectively produces curium

    NASA Technical Reports Server (NTRS)

    Anderson, R. W.; Milstead, J.; Stewart, D. C.

    1967-01-01

    Computer study was made on the production of multicurie amounts of highly alpha-active curium 242 from americium 241 irradiation. The information available includes curium 242 yields, curium composition, irradiation data, and production techniques and safeguards.

  17. The present situation of the irradiation application industry and irradiation facilities in Japan

    NASA Astrophysics Data System (ADS)

    Mizusawa, K.; Baba, T.

    2003-08-01

    The irradiation application industry and irradiation facilities in Japan have been making slow but steady progress for the past 2-3 years. Beside conventional applications, new ones such as carbon fibers and membrane filters have come into the market. There are a lot of new applications about to emerge. PE tubing, already is in the European market, is being evaluated by end users in Japan. Cleaning of dioxin in exhaust gas was successfully tested at a pilot plant. Cross-linked PTFE and polyamide are waiting customers' evaluations as an engineering plastic. Surface cross-linking of artificial polycarbonate teeth has yielded remarkable experimental results. Cross-linking of polycaprolactone will be useful for biodegradable products. Being aware of the future growth of irradiation industry, contract service providers opened new facilities or increased their capability. Beside in-house facilities, there are now three Co-60 facilities and nine EB facilities available for contract irradiation in Japan.

  18. Electrokinetic and surface chemical characterizations of an irradiated microfiltration polysulfone membrane: comparison of two irradiation doses.

    PubMed

    de Lara, R; Benavente, J

    2007-06-15

    The effect of ionizing radiation on the surface and electrokinetic characteristic parameters for a porous membrane of pore size 0.2 mum is determined and correlated with the irradiation dose (10 and 80 J/kg). Changes in NaCl permeability and membrane system electrical resistance determined from diffusion and impedance spectroscopy measurements are consistent with the increase of membrane pore radii/porosity, in agreement with SEM micrographs and reported results. Low irradiation dose seems to clean the membrane surface of impurities, according to XPS results, but the increase of irradiation doses could affect surface roughness. Due to the relatively high pore radius, ion transport numbers are practically independent of radiation and dose, but irradiation slightly modifies the membrane solution interface by increasing its weakly electronegative character, which could be of interest in the ultrafiltration of proteins or macromolecules.

  19. Calibration of the Odyssey Photosynthetic Irradiance Recorder for Absolute Irradiance Measures

    EPA Science Inventory

    Researchers are increasingly interested in measuring hotosynthetically active radiation (PAR) because of its importance in determining the structure and function of lotic ecosystems. The Odyssey Photosynthetic Irradiance Recorder is an affordable PAR meter gaining popularity am...

  20. Optical imaging of irradiated and non-irradiated hearts (Conference Presentation)

    NASA Astrophysics Data System (ADS)

    Bolin, Stephanie; Chen, Guanchu; Medhora, Meetha M.; Camara, Amadou K. S.; Ranji, Mahsa

    2016-03-01

    Objective: In this study, the metabolic state of the heart tissue is studied in a rodent model of ischemia and reperfusion (IR) in rats exposed to irradiation injury using a cryofluorescence imaging technique. Mitochondrial metabolic state is evaluated by autofluorescence of mitochondrial metabolic coenzymes NADH and FAD. The redox ratio (NADH/FAD) is used as a biochemical/metabolic marker of oxidative stress, before, during and after IR. Materials and methods: Hearts were extracted from non-irradiated (control) and irradiated rats (Irr) given 15 Gy whole thorax irradiation rats (WTI). After 35 days, before the onset of radiation pneumonitis, these two groups of hearts were subjected to one of three treatments; Time control (TC; hearts perfused for the duration of the protocol without ischemia or IR), 25 minutes ischemia with no reperfusion and 25 minutes ischemia followed by 60 minutes reperfusion (IR). Hearts were removed from the Langendorff perfusion system and immediately snap frozen in liquid N2 to preserve the metabolic state after injury; 3-dimensional (3D) cryo-fluorescent imager was used to obtain in fixed time NADH and FAD fluorescence images and their distribution across the entire ventricles. In this study, a 30-μm axial resolution was used resulting in 550 cross-section images per heart. The 3D images of the redox ratio and their respective histograms were calculated in the six groups of hearts. Results: We compared the mean values of the redox ratio in each group, which demonstrate a reduced mitochondrial redox state in both irradiated and non-irradiated ischemic hearts and an oxidized mitochondrial redox state for both irradiated and non-irradiated ischemia-reperfusion hearts compared to control hearts. For non-irradiated hearts, ischemia and IR injuries resulted respectively in 61% increase and 54% decrease in redox ratio when compared with TC. For irradiated hearts, ischemia and IR injuries resulted respectively in 90% increase and 50% decrease

  1. IRRADIATION EFFECTS ON THE PHYSICAL CHARACTERISTICS OF SEWAGE SLUDGE

    SciTech Connect

    Lee, M-J.; Lee, J-K.; Yoo, D-H.; Ho, K.

    2004-10-05

    The radiation effects on the physical characteristic of the sewage sludge were studied in order to obtain information which will be used for study on the enhancement of the sludge's dewaterability. Water contents, capillary suction time, zeta potential, irradiation dose, sludge acidity, total solid concentration, sludge particle size and microbiology before and after irradiation were investigated. Irradiation gave an effect on physical characteristics sludge. Water content in sludge cake could be reduced by irradiation at the dose of 10kGy.

  2. Ionospheric Change and Solar EUV Irradiance

    NASA Astrophysics Data System (ADS)

    Sojka, J. J.; David, M.; Jensen, J. B.; Schunk, R. W.

    2011-12-01

    The ionosphere has been quantitatively monitored for the past six solar cycles. The past few years of observations are showing trends that differ from the prior cycles! Our good statistical relationships between the solar radio flux index at 10.7 cm, the solar EUV Irradiance, and the ionospheric F-layer peak density are showing indications of divergence! Present day discussion of the Sun-Earth entering a Dalton Minimum would suggest change is occurring in the Sun, as the driver, followed by the Earth, as the receptor. The dayside ionosphere is driven by the solar EUV Irradiance. But different components of this spectrum affect the ionospheric layers differently. For a first time the continuous high cadence EUV spectra from the SDO EVE instrument enable ionospheric scientists the opportunity to evaluate solar EUV variability as a driver of ionospheric variability. A definitive understanding of which spectral components are responsible for the E- and F-layers of the ionosphere will enable assessments of how over 50 years of ionospheric observations, the solar EUV Irradiance has changed. If indeed the evidence suggesting the Sun-Earth system is entering a Dalton Minimum periods is correct, then the comprehensive EVE solar EUV Irradiance data base combined with the ongoing ionospheric data bases will provide a most fortuitous fiduciary reference baseline for Sun-Earth dependencies. Using the EVE EUV Irradiances, a physics based ionospheric model (TDIM), and 50 plus years of ionospheric observation from Wallops Island (Virginia) the above Sun-Earth ionospheric relationship will be reported on.

  3. Experimental plan for irradiation experiment HRB-21

    SciTech Connect

    Goodin, D. T.; Kania, M. J.; Patton, B. W.

    1989-04-01

    Irradiation experiment HRB-21 is the first in a series of test capsules that are designed to provide a fuel-performance data base to be used for the validation of modular high-temperature gas-cooled reactor (MHTGR) coated-particle fuel performance models under MHTGR normal operating conditions and specific licensing basis events. Capsule HRB-21 will contain an advanced TRISO-P UCO/ThO{sub 2} - coated-particle fuel system with demonstrated low defective-particle fraction ({le}5 {times} 10{sup {minus}5}) and a heavy metal-contamination fraction ({le}1 {times} 10{sup {minus}5}) that meets MHTGR quality specifications. The coated particles and fuel compacts were fabricated in laboratory-scale facilities using MHTGR reference procedures at General Atomics (GA). Nearly 150,000 fissile and fertile particles will be irradiated in capsule HRB-21 at a mean volumetric fuel temperature of 975{degree}C and will achieve a peak fissile burnup of 26% fissions per initial metal atom (FIMA) while accumulating a fast neutron fluence of about 4.5 {times} 10{sup 25} neutrons/m{sup 2}. This experiment is a cooperative effort between the US Department of Energy (DOE) and the Japan Atomic Energy Research Institute (JAERI). The participants are the Oak Ridge National Laboratory (ORNL), GA, and the Tokai Research Establishment. Capsule HRB-21 will contain the US MHTGR fuel specimens, and a companion capsule, HRB-22, will contain the JAERI fuel. The irradiation will take place in the removable beryllium reflector facility of the High Flux Isotope Reactor (HFIR) at ORNL. The performance of the fuel during irradiation will be closely monitored through on-line fission gas release measurements. Detailed postirradiation examination and conduction cooldown simulation testing will be performed on the irradiated fuel compacts from both the HRB-21 and HRB-22 capsules. 5 refs., 9 figs., 6 tabs.

  4. Updated Results of Ultrasonic Transducer Irradiation Test

    SciTech Connect

    Daw, Joshua; Palmer, Joe; Ramuhalli, Pradeep; Keller, Paul; Montgomery, Robert; Chien, Hual-Te; Tittmann, Bernhard; Reinhardt, Brian; Kohse, Gordon; Rempe, Joy; Villard, J.F.

    2015-07-01

    Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. These efforts are limited by the lack of identified ultrasonic transducer materials capable of long term performance under irradiation test conditions. To address this need, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate the performance of promising magnetostrictive and piezoelectric transducers in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 10{sup 21} n/cm{sup 2}. A multi-National Laboratory collaboration funded by the Nuclear Energy Enabling Technologies Advanced Sensors and Instrumentation (NEET-ASI) program also provided initial support for this effort. This irradiation, which started in February 2014, is an instrumented lead test and real-time transducer performance data are collected along with temperature and neutron and gamma flux data. The irradiation is ongoing and will continue to approximately mid-2015. To date, very encouraging results have been attained as several transducers continue to operate under irradiation. (authors)

  5. Biodegradation of selected UV-irradiated and non-irradiated polycyclic aromatic hydrocarbons (PAHs).

    PubMed

    Lehto, Kirsi-Maarit; Puhakka, Jaakko A; Lemmetyinen, Helge

    2003-08-01

    Biodegradation of UV-irradiated anthracene, pyrene, benz[a]anthracene, and dibenz[a,h]anthracene was compared to that of the non-irradiated samples, individually and in synthetic mixtures with enrichment cultures. Combined treatment was repeated for individual anthracene and for the PAH mixture with Sphingomonas sp. strain EPA 505 and Sphingomonas yanoikuyae. Enrichment culture studies were performed on the PAH mixtures in the presence of the main photoproduct of anthracene, pure 9,10-anthracenedione. Photochemically pretreated creosote solutions were also subjected to biodegradation and the results were compared to those of the non-irradiated solutions. The primary interest was on 16 polycyclic aromatic hydrocarbons (PAHs) listed as priority pollutants by European Union (EU) and the United States Environmental Protection Agency (USEPA). Irradiation accelerated the biodegradation onset for anthracene, pyrene, and benz[a]anthracene when they were treated individually. The biodegradation of irradiated pyrene started with no lag phase and was complete by 122 h whereas biodegradation of the non-irradiated sample had a lag of 280 h and resulted in complete degradation by 720 h. Biodegradation of PAHs was accelerated in synthetic mixtures, especially in the presence of pure 9,10-anthracenedione. In general, irradiation had no effect on the biodegradation of PAHs incubated in synthetic mixtures or with pure cultures. Under current experimental conditions, the UV-irradiation invariably reduced the biodegradation of PAHs in creosote. Based on the results of the present and previous photochemical-biological studies of PAHs, the influence of the photochemical pretreatment on the biodegradation is highly dependent on the compounds being treated and other process parameters.

  6. Phytosanitary irradiation and fresh fruit quality: Cultivar and maturity effects

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Irradiation is an effective quarantine treatment for global trade of fresh produce. Variation in cultivars and maturity stages can impact the tolerance of fresh fruits to irradiation for the purposes of quarantine security. Tolerance thresholds for irradiated fruit are lacking for a large number of ...

  7. Food irradiation regulatory development in the U.S.

    NASA Astrophysics Data System (ADS)

    Miller, Sandford A.; Coleman, Eugene C.

    The Food and Drug Administration's involvement in food irradiation dates back more than thirty years. The agency has been involved with the wholesomeness testing of the irradiated foods from both nutritional and toxicological standpoints. Knowledge about the nutritional and toxicological aspects of irradiated foods is fundamental in the development of a regulatory strategy for assuring the safe use of such foods.

  8. Coincidence doppler broadening study in electron-irradiated polyurethane

    NASA Astrophysics Data System (ADS)

    Yang, D. J.; Zhang, J. D.; Leung, J. K. C.; Beling, C. D.; Liu, L. B.

    2007-06-01

    Coincidence doppler broadening measurements on electron-irradiated polyurethanes were performed in the presence of air. It is shown that, after a certain electron irradiation, the momentum density distributions of annihilation electrons have obvious changes for the high crosslinking polyurethane, but no significant changes have been observed for the low crosslinking polyurethane. The results were performed to analyse by irradiation crosslinking and degradation principles.

  9. Response of neutron-irradiated RPV steels to thermal annealing

    SciTech Connect

    Iskander, S.K.; Sokolov, M.A.; Nanstad, R.K.

    1997-03-01

    One of the options to mitigate the effects of irradiation on reactor pressure vessels (RPVs) is to thermally anneal them to restore the fracture toughness properties that have been degraded by neutron irradiation. This paper summarizes experimental results of work performed at the Oak Ridge National Laboratory (ORNL) to study the annealing response of several irradiated RPV steels.

  10. Soluble irradiation targets and methods for the production of radiorhenium

    SciTech Connect

    Vanderhevden, J.L.E.; Su, F.M.; Ehrhardt, G.J.

    1992-09-08

    This patent describes a method of producing a rhenium-188 radionuclide generator. It comprises irradiating a water soluble irradiation target selected from the group consisting of sodium tungstate and lithium tungstate, reacting the irradiated target with an aqueous zirconium solution to obtain an insoluble zirconium tungstate gel, and disposing the zirconium tungstate in an elutable container to obtain the rhenium-188 radionuclide generator.

  11. Irradiation creep of various ferritic alloys irradiated {approximately}400 C in the PFR and FFTF reactors

    SciTech Connect

    Toloczko, M.B.; Garner, F.A.; Eiholzer, C.R.

    1998-03-01

    Three ferritic alloys were irradiated in two fast reactors to doses of 50 dpa or more at temperatures near 400 C. One martensitic alloy, HT9, was irradiated in both the FFTF and PFR reactors. PFR is the Prototype Fast Reactor in Dourneay, Scotland, and FFTF is the Fast Flux Test Facility in Richland, WA. D57 is a developmental alloy that was irradiated in PFR only, and MA957 is a Y{sub 2}O{sub 3} dispersion-hardened ferritic alloy that was irradiated only in FFTF. These alloys exhibited little or no void swelling at {approximately}400 C. Depending on the alloy starting condition, these steels develop a variety of non-creep strains early in the irradiation that are associated with phase changes. Each of these alloys creeps at a rate that is significantly lower than that of austenitic steels irradiated in the same experiments. The creep compliance for ferritic alloys in general appears to be {approximately}0.5 {times} 10{sup {minus}6} MPa{sup {minus}1} dpa{sup {minus}1}, independent of both composition and starting state. The addition of Y{sub 2}O{sub 3} as a dispersoid does not appear to change the creep behavior.

  12. Detection of low amount of irradiated ingredients in non-irradiated precooked meals

    NASA Astrophysics Data System (ADS)

    Marchioni, Eric; Horvatovich, Peter; Ndiaye, Bara; Miesch, Michel; Hasselmann, Claude

    2002-03-01

    The application of the European Standards for the detection of irradiated food by thermoluminescence of silicates, electron-spin resonance spectroscopy of bones or gas chromatography-mass spectrometry of 2-alkylcyclobutanones does not allow the detection of irradiated ingredients included in small quantity in the matrix of a food which has not been irradiated, but which could be subjected to various processing technologies such as cooking, freezing or storage. The use of an enzymatic food hydrolysis carried out at moderated temperature, for the extraction of the food-contaminating silicate minerals and bone fragments, followed by a purification of the extracts by a high-density aqueous solution of sodium polytungstate, allows a simultaneous detection of weak inclusions (0.1% m:m) of irradiated spices and mechanically deboned turkey meat (MRM) included in various precooked foods. Moreover, the use of a supercritical fluid extraction procedure for the 2-alkylcyclobutanones or an additional purification step of the lipid extracts made it possible to lower the detection limit of the 2-alkylcyclobutanones radiation-induced from triglycerides. Using gas chromatography-mass spectrometry, down to 0.5% (m:m) of irradiated MRM included in non-irradiated chicken quenelles could be detected.

  13. Sensitivity of ultrasonic nonlinearity to irradiated, annealed, and re-irradiated microstructure changes in RPV steels

    SciTech Connect

    Matlack, Katie; Kim, J-Y.; Wall, J.J.; Jacobs, L.J.; Sokolov, Mikhail A

    2014-05-01

    The planned life extension of nuclear reactors throughout the US and abroad will cause reactor vessel and internals materials to be exposed to more neutron irradiation than was originally intended. A nondestructive evaluation (NDE) method to monitor radiation damage would enable safe and cost-effective continued operation of nuclear reactors. Radiation damage in reactor pressure vessel (RPV) steels causes microstructural changes that leave the material in an embrittled state. Nonlinear ultrasound is an NDE technique quantified by the measurable acoustic nonlinearity parameter, which is sensitive to microstructural changes in metallic materials such as dislocations, precipitates and their combinations. Recent research has demonstrated the sensitivity of the acoustic nonlinearity parameter to increasing neutron fluence in representative RPV steels. The current work considers nonlinear ultrasonic experiments conducted on similar RPV steel samples that had a combination of irradiation, annealing, re-irradiation, and/or re-annealing to a total neutron fluence of 0.5 5 1019 n/cm2 (E > 1 MeV) at an irradiation temperature of 290 C. The acoustic nonlinearity parameter generally increased with increasing neutron fluence, and consistently decreased from the irradiated to the annealed state over different levels of neutron fluence. Results of the measured acoustic nonlinearity parameter are compared with those from previous measurements on other RPV steel samples. This comprehensive set of results illustrates the dependence of the measured acoustic nonlinearity parameter on neutron fluence, material composition, irradiation temperature and annealing.

  14. Influence du débit et de la répartition de dose sur l'incidence des cancers pulmonaires après inhalation d'émetteurs

    NASA Astrophysics Data System (ADS)

    Fritsch, P.; Dudoignon, N.; Morlier, J. P.; Monchaux, G.; Morin, M.

    1998-04-01

    We have discussed experimental results reported on the influence of dose rate and dose distribution on the incidence of lung tumors after inhalation exposure to α emitters. New experiments have been carried out to characterize the range of tumor risk which could vary over more than a factor 20 depending on the α activity of the inhaled particles. Long term effects induced in rats after inhalation of poorly soluble 237NpO2 and industrial PuO2 with a similar granulometry will be compared, the specific activities of which varying within a factor 500. Nous avons rapporté les différentes données expérimentales de cancérogenèse pulmonaire qui montrent une variation du risque d'induction des tumeurs après inhalation de radionucléides émetteurs α selon le débit et la répartition de dose. De nouvelles expérimentations ont été initiées afin de préciser ces variations qui s'étalent sur plus d'un facteur 20. Elles consistent à comparer les effets induits chez le rat après exposition à des aérosols de 237NpO2 et de PuO2 d'origine industrielle peu solubles et de granulométrie analogue dont les activités spécifiques diffèrent d'un facteur 500.

  15. Effect of low-level laser irradiating point on immunity

    NASA Astrophysics Data System (ADS)

    Cai, ChangSong; Qi, Qiong-fang; Xin, Jiang

    1993-03-01

    This paper reports that cellular immune function was observed when He-Ne laser was used to irradiate `zusanli' point in rats using various power, time, and periods. The indicator was a lymphocyte transformation test (LTT) by MTT colorimetric analysis. The best irradiating condition was determined, the effect and both virtues and defects of the laser were compared with those of electropuncture. The results show (1) LTT was enhanced in the group of laser irradiating point, but LTT was not enhanced in non-point (t' test, P < 0.01). (2) Lower power -- 2 mW or 5 mW of irradiating for 15 - 20 min, was better; 10 mW or 20 mW of irradiating for 10 - 15 min was suitable. Prolonged irradiating time did not enhance the immune function of the rats. On the contrary, immune function was inhibited. (3) A 7-day period of irradiating was best (once a day, 10 mW for 10 min). Enhanced LTT was not seen when irradiation days were added (SNK, P > 0.05). (4) Laser irradiation point and electropuncture were compared with vehicle control, LTT in the former two groups was enhanced significantly (ANOVA, P < 0.01), and laser irradiating point and electropuncture had the same effect (SNK, P > 0.05). The data suggest that laser irradiating point was able to enhance cell immunity and the enhancement of LTT had a point specific characteristic. The best condition of laser irradiating point was 2 mW for 15 - 20 min, and 10 mW or 20 mW for 10 - 15 min. The best period was 7-day irradiation. The results show laser irradiating the point may activate the main and collateral channels system, then modify the immune function of the body. Our observations provide experimental evidence for proper clinical application of laser irradiating points. The paper theoretically discusses and analyzes the experiment results in detail.

  16. Advanced Numerical Model for Irradiated Concrete

    SciTech Connect

    Giorla, Alain B.

    2015-03-01

    In this report, we establish a numerical model for concrete exposed to irradiation to address these three critical points. The model accounts for creep in the cement paste and its coupling with damage, temperature and relative humidity. The shift in failure mode with the loading rate is also properly represented. The numerical model for creep has been validated and calibrated against different experiments in the literature [Wittmann, 1970, Le Roy, 1995]. Results from a simplified model are shown to showcase the ability of numerical homogenization to simulate irradiation effects in concrete. In future works, the complete model will be applied to the analysis of the irradiation experiments of Elleuch et al. [1972] and Kelly et al. [1969]. This requires a careful examination of the experimental environmental conditions as in both cases certain critical information are missing, including the relative humidity history. A sensitivity analysis will be conducted to provide lower and upper bounds of the concrete expansion under irradiation, and check if the scatter in the simulated results matches the one found in experiments. The numerical and experimental results will be compared in terms of expansion and loss of mechanical stiffness and strength. Both effects should be captured accordingly by the model to validate it. Once the model has been validated on these two experiments, it can be applied to simulate concrete from nuclear power plants. To do so, the materials used in these concrete must be as well characterized as possible. The main parameters required are the mechanical properties of each constituent in the concrete (aggregates, cement paste), namely the elastic modulus, the creep properties, the tensile and compressive strength, the thermal expansion coefficient, and the drying shrinkage. These can be either measured experimentally, estimated from the initial composition in the case of cement paste, or back-calculated from mechanical tests on concrete. If some

  17. Planarian immobilization, partial irradiation, and tissue transplantation.

    PubMed

    Guedelhoefer, Otto C; Sánchez Alvarado, Alejandro

    2012-08-06

    The planarian, a freshwater flatworm, has proven to be a powerful system for dissecting metazoan regeneration and stem cell biology. Planarian regeneration of any missing or damaged tissues is made possible by adult stem cells termed neoblasts. Although these stem cells have been definitively shown to be pluripotent and singularly capable of reconstituting an entire animal, the heterogeneity within the stem cell population and the dynamics of their cellular behaviors remain largely unresolved. Due to the large number and wide distribution of stem cells throughout the planarian body plan, advanced methods for manipulating subpopulations of stem cells for molecular and functional study in vivo are needed. Tissue transplantation and partial irradiation are two methods by which a subpopulation of planarian stem cells can be isolated for further study. Each technique has distinct advantages. Tissue transplantation allows for the introduction of stem cells, into a naïve host, that are either inherently genetically distinct or have been previously treated pharmacologically. Alternatively, partial irradiation allows for the isolation of stem cells within a host, juxtaposed to tissue devoid of stem cells, without the introduction of a wound or any breech in tissue integrity. Using these two methods, one can investigate the cell autonomous and non-autonomous factors that control stem cell functions, such as proliferation, differentiation, and migration. Both tissue transplantation and partial irradiation have been used historically in defining many of the questions about planarian regeneration that remain under study today. However, these techniques have remained underused due to the laborious and inconsistent nature of previous methods. The protocols presented here represent a large step forward in decreasing the time and effort necessary to reproducibly generate large numbers of grafted or partially irradiated animals with efficacies approaching 100 percent. We cover the

  18. Planarian Immobilization, Partial Irradiation, and Tissue Transplantation

    PubMed Central

    Guedelhoefer IV, Otto C.; Sánchez Alvarado, Alejandro

    2012-01-01

    The planarian, a freshwater flatworm, has proven to be a powerful system for dissecting metazoan regeneration and stem cell biology1,2. Planarian regeneration of any missing or damaged tissues is made possible by adult stem cells termed neoblasts3. Although these stem cells have been definitively shown to be pluripotent and singularly capable of reconstituting an entire animal4, the heterogeneity within the stem cell population and the dynamics of their cellular behaviors remain largely unresolved. Due to the large number and wide distribution of stem cells throughout the planarian body plan, advanced methods for manipulating subpopulations of stem cells for molecular and functional study in vivo are needed. Tissue transplantation and partial irradiation are two methods by which a subpopulation of planarian stem cells can be isolated for further study. Each technique has distinct advantages. Tissue transplantation allows for the introduction of stem cells, into a naïve host, that are either inherently genetically distinct or have been previously treated pharmacologically. Alternatively, partial irradiation allows for the isolation of stem cells within a host, juxtaposed to tissue devoid of stem cells, without the introduction of a wound or any breech in tissue integrity. Using these two methods, one can investigate the cell autonomous and non-autonomous factors that control stem cell functions, such as proliferation, differentiation, and migration. Both tissue transplantation5,6 and partial irradiation7 have been used historically in defining many of the questions about planarian regeneration that remain under study today. However, these techniques have remained underused due to the laborious and inconsistent nature of previous methods. The protocols presented here represent a large step forward in decreasing the time and effort necessary to reproducibly generate large numbers of grafted or partially irradiated animals with efficacies approaching 100 percent. We

  19. La physique cométaire après l'exploration de la comète de Halley

    NASA Astrophysics Data System (ADS)

    Encrenaz, Thérèse

    The 1986 apparition of Comet Halley has provided a unique opportunity for cometary research. An exceptional international cooperative program has been set up, and the comet has been investigated by five space probes in March 1986. Many new parent-molecules have been identified : H2O, CO2, CO, H2CO, HCN, OCS. In addition, a spectral signature attributed to hydrocarbons, either in the gaseous or in the solid phase, has been detected at 3 μm. The spatial distribution of radicals has been obtained, as well as the dust distribution. The silicate signature has been detected at 10 μm, and the signature of water ice is marginally present around 3 μm. The nucleus has been found to be larger (7.5 x 7.5 x 15 km) and warmer than expected, with a very low albedo (0.04). It might be covered with refractory material, possibly comparable to the organic refractory material which is formed by irradiation of ices with UV flux or energetic particles. From mass spectrometer experiments, there is evidence for light, « primitive » particles (« CHON » particles) in large amounts. The dust impact experiments have also detected large abundances of very small particles (10 -15 to 10-17 g). In summary, these results confirm the « primitive », untransformed origin of comets and their possible analogy with presolar and interstellar material. L'apparition de la comète de Halley en 1986 a procuré une occasion unique pour la recherche cométaire. Elle a été l'objet d'une campagne d'observation au sol sans précédent, et d'un effort de coopération international exceptionnel ; enfin, la comète a été visitée par cinq sondes spatiales en mars 1986. De nombreuses nouvelles molécules-mères ont été identifiées : H2O, CO2, CO, H2CO, HCN, OCS... De plus, une signature spectrale a été identifiée à 3 μm, et attribuée à des hydrocarbures, sous une forme solide ou gazeuse. La distribution spatiale des radicaux a été obtenue, ainsi que celle de la poussière. La signature des

  20. A study on preparation of glucoamylase by irradiation

    NASA Astrophysics Data System (ADS)

    Ruyan, Chen; Junming, Lan; Youqi, Yan; Can, Tao; Shijie, Li; Liangbi, Song

    1993-10-01

    A study on preparation of industrial glucoamylase irradiated by 60Co gamma-ray showed that an abvious change took place in the extraviolet absorption spectrum and the pH - value of the enzyme solution and the activity of the enzyme preparation was much more resistant to irradiation than that of microbes contained in the preparation. The result indicates that irradiated glucoamylase preparation is not only favourable to activity preservation but also is improved in the hygienic quality of products. A comparison of the various properties of irradiated enzyme preparation with those of unirradiated one has proved that irradiation does not change the normal application of glucoamylase preparation.

  1. Application of gamma irradiation for inhibition of food allergy

    NASA Astrophysics Data System (ADS)

    Byun, Myung-Woo; Lee, Ju-Woon; Yook, Hong-Sun; Jo, Cheorun; Kim, Hee-Yun

    2002-03-01

    This study was carried out to evaluate the application of food irradiation technology as a method for reducing food allergy. Milk β-lactoglobulin, chicken egg albumin, and shrimp tropomyosin were used as model food allergens for experiments on allergenic and molecular properties by gamma irradiation. The amount of intact allergens in an irradiated solution was reduced by gamma irradiation depending upon the dose. These results showed that epitopes on the allergens were structurally altered by radiation treatment and that the irradiation technology can be applied to reduce allergenicity of allergic foods.

  2. Mechanical properties of UV irradiated rat tail tendon (RTT) collagen.

    PubMed

    Sionkowska, Alina; Wess, Tim

    2004-04-01

    The mechanical properties of RTT collagen tendon before and after UV irradiation have been investigated by mechanical testing (Instron). Air-dried tendon were submitted to treatment with UV irradiation (wavelength 254 nm) for different time intervals. The changes in such mechanical properties as breaking strength and percentage elongation have been investigated. The results have shown, that the mechanical properties of the tendon were greatly affected by time of UV irradiation. Ultimate tensile strength and ultimate percentage elongation decreased after UV irradiation of the tendon. Increasing UV irradiation leads to a decrease in Young's modulus of the tendon.

  3. Food irradiation in the UK and the European Directive

    NASA Astrophysics Data System (ADS)

    Woolston, John

    2000-03-01

    Food irradiation in the UK has been authorised since the early 1990s. In principle it is possible to irradiate a wide range of foods for a variety of purposes. In practice food irradiation is virtually non-existent. The structure of food retailing in the UK, a continual stream of food safety scares and a developing public 'crisis of confidence' in the food producer/supply chain have combined to make the future for food irradiation look bleak. The new European Directive on Food Irradiation is unlikely to alter this outlook.

  4. Influence of gamma ray irradiation on metakaolin based sodium geopolymer

    NASA Astrophysics Data System (ADS)

    Lambertin, D.; Boher, C.; Dannoux-Papin, A.; Galliez, K.; Rooses, A.; Frizon, F.

    2013-11-01

    Effects of gamma irradiation on metakaolin based Na-geopolymer have been investigated by external irradiation. The experiments were carried out in a gamma irradiator with 60Co sources up to 1000 kGy. Various Na-geopolymer with three H2O/Na2O ratios have been studied in terms of hydrogen radiolytic yield. The results show that hydrogen production increases linearly with water content. Gamma irradiation effects on Na-geopolymer microstructure have been investigated with porosity measurements and X-ray pair distribution function analysis. A change of pore size distribution and a structural relaxation have been found after gamma ray irradiation.

  5. Irradiation creep and swelling of various austenitic alloys irradiated in PFR and FFTF

    SciTech Connect

    Garner, F.A.; Toloczko, M.B.

    1996-10-01

    In order to use data from surrogate neutron spectra for fusion applications, it is necessary to analyze the impact of environmental differences on property development. This is of particular importance in the study of irradiation creep and its interactions with void swelling, especially with respect to the difficulty of separation of creep strains from various non-creep strains. As part of an on-going creep data rescue and analysis effort, the current study focuses on comparative irradiations conducted on identical gas-pressurized tubes produced and constructed in the United States from austenitic steels (20% CW 316 and 20% CW D9), but irradiated in either the Prototype Fast Reactor (PFR) in the United Kingdom or the Fast Flux Test Facility in the United States. In PFR, Demountable Subassemblies (DMSA) serving as heat pipes were used without active temperature control. In FFTF the specimens were irradiated with active ({+-}{degrees}5C) temperature control. Whereas the FFTF irradiations involved a series of successive side-by-side irradiation, measurement and reinsertion of the same series of tubes, the PFR experiment utilized simultaneous irradiation at two axial positions in the heat pipe to achieve different fluences at different flux levels. The smaller size of the DMSA also necessitated a separation of the tubes at a given flux level into two groups (low-stress and high-stress) at slightly different axial positions, where the flux between the two groups varied {le}10%. Of particular interest in this study was the potential impact of the two types of separation on the derivation of creep coefficients.

  6. [Dosimetric comparison of external partial breast irradiation with whole breast irradiation and partial breast brachytherapy].

    PubMed

    Bodács, István; Polgár, Csaba; Major, Tibor

    2014-06-01

    Different techniques exist for the delivery of radiotherapy after breast conserving surgery. The conventional method is whole breast irradiation. However, in selected patients partial breast irradiation can be performed, either with external beams or brachytherapy. In the current study three irradiation techniques are compared regarding dosimetric aspects. Treatment plans of thirty women treated with external beam conformal partial breast irradiation (CONF) were evaluated using dose-volume histograms. For the same patients whole breast irradiation plans (WBI) were made and compared with the CONF ones. Breast and lung of both sides, and heart at left sided lesions were contoured as organs at risk. After this, dose plans of another thirty patients treated with interstitial brachytherapy (IBT) were analyzed and compared with the CONF plans. According to our results the 90% isodose curve covered at least 97% of the target volume at all three techniques, and this value was 100% for CONF. The maximal dose within target volume was 106% in CONF and 115% in WBI plans. Volume of ipsilateral breast receiving the prescribed dose was 66%, 15% and 13% in the WBI, CONF and IBT plans, respectively. The dose to the contralateral breast was less for CONF compared to WBI. Volume of the ipsilateral lung receiving 30% of the prescribed dose was 15%, 8% and 1%, the maximal dose was 105%, 94% and 47% in the WBI, CONF and IBT plans, respectively. In the same order the maximal dose to the heart was 82%, 49% and 25%, while the dose irradiated to 5% of the heart volume was 27%, 19% and 14% at left sided lesions. Regarding target coverage, the conformal technique was the best, and the dose was more homogeneous than at WBI. With respect to dose to organs at risk the partial breast irradiation techniques were much more favorable than WBI, and the lowest doses occurred in the IBT treatment plans.

  7. Post-irradiation stability of polyvinyl chloride at sterilizing doses

    NASA Astrophysics Data System (ADS)

    Naimian, F.; Katbab, A. A.; Nazokdast, H.

    1994-12-01

    Post-irradiation stability of plasticized PVC irradiated by 60Co gamma ray at sterilizing doses has been studied. Effects of irradiation upon chemical structure, mechanical properties and rheological behaviour of samples contained different amounts of Di(2-ethylhexyl)phthalate as plasticizer have been investigated. Formation of conjugated double bonds, carbonyl and hydroxyl groups have been followed by UV and FTIR spectrometers up to 6 months after irradiation. FTIR spectra of irradiated samples showed no significant changes in carbonyl and hydroxyl groups even 6 months after irradiation. However, changes in UV-visible spectra was observed for the irradiated samples up to 6 months post-irradiation. This has been attributed to the formation of polyenes which leads to the discoloration of this polymer. Despite a certain degree of discoloration, it appears that the mechanical properties of PVC are not affected by irradiation at sterilizing doses. No change in the melt viscosity of the irradiated PVC samples with post-irradiation was observed, which is in consistent with the IR results.

  8. Gamma irradiation influence on physical properties of milk proteins

    NASA Astrophysics Data System (ADS)

    Cieśla, K.; Salmieri, S.; Lacroix, M.; Tien, C. Le

    2004-09-01

    Gamma irradiation was found to be an effective method for the improvement of both barrier and mechanical properties of the edible films and coatings based on calcium and sodium caseinates alone or combined with some globular proteins. Our current studies concern gamma irradiation influence on the physical properties of calcium caseinate-whey protein isolate-glycerol (1:1:1) solutions and gels, used for films preparation. Irradiation of solutions was carried out with Co-60 gamma rays applying 0 and 32 kGy dose. The increase in viscosity of solutions was found after irradiation connected to induced crosslinking. Lower viscosity values were detected, however, after heating of the solutions irradiated with a 32 kGy dose than after heating of the non-irradiated ones regarding differences in the structure of gels and resulting in different temperature-viscosity curves that were recorded for the irradiated and the non-irradiated samples during heating and cooling. Creation of less stiff but better ordered gels after irradiation arises probably from reorganisation of aperiodic helical phase and β-sheets, in particular from increase of β-strands, detected by FTIR. Films obtained from these gels are characterised by improved barrier properties and mechanical resistance and are more rigid than those prepared from the non-irradiated gels. The route of gel creation was investigated for the control and the irradiated samples during heating and the subsequent cooling.

  9. Microarchitecture of irradiated bone: comparison with healthy bone

    NASA Astrophysics Data System (ADS)

    Bléry, Pauline; Amouriq, Yves; Guédon, Jeanpierre; Pilet, Paul; Normand, Nicolas; Durand, Nicolas; Espitalier, Florent; Arlicot, Aurore; Malard, Olivier; Weiss, Pierre

    2012-03-01

    The squamous cell carcinomas of the upper aero-digestive tract represent about ten percent of cancers. External radiation therapy leads to esthetic and functional consequences, and to a decrease of the bone mechanical abilities. For these patients, the oral prosthetic rehabilitation, including possibilities of dental implant placement, is difficult. The effects of radiotherapy on bone microarchitecture parameters are not well known. Thus, the purpose of this study is to assess the effects of external radiation on bone micro architecture in an experimental model of 25 rats using micro CT. 15 rats were irradiated on the hind limbs by a single dose of 20 Grays, and 10 rats were non irradiated. Images of irradiated and healthy bone were compared. Bone microarchitecture parameters (including trabecular thickness, trabecular number, trabecular separation, connectivity density and tissue and bone volume) between irradiated and non-irradiated bones were calculated and compared using a Mann and Whitney test. After 7 and 12 weeks, images of irradiated and healthy bone are different. Differences on the irradiated and the healthy bone populations exhibit a statistical significance. Trabecular number, connectivity density and closed porosity are less important on irradiated bone. Trabecular thickness and separation increase for irradiated bone. These parameters indicate a decrease of irradiated bone properties. Finally, the external irradiation induces changes on the bone micro architecture. This knowledge is of prime importance for better oral prosthetic rehabilitation, including implant placement.

  10. Mechanical properties for irradiated face-centred cubic nanocrystalline metals.

    PubMed

    Xiao, X Z; Song, D K; Chu, H J; Xue, J M; Duan, H L

    2015-05-08

    In this paper, a self-consistent plasticity theory is proposed to model the mechanical behaviours of irradiated face-centred cubic nanocrystalline metals. At the grain level, a tensorial crystal model with both irradiation and grain size effects is applied for the grain interior (GI), whereas both grain boundary (GB) sliding with irradiation effect and GB diffusion are considered in modelling the behaviours of GBs. The elastic-viscoplastic self-consistent method with considering grain size distribution is developed to transit the microscopic behaviour of individual grains to the macroscopic properties of nanocrystals (NCs). The proposed theory is applied to model the mechanical properties of irradiated NC copper, and the feasibility and efficiency have been validated by comparing with experimental data. Numerical results show that: (i) irradiation-induced defects can lead to irradiation hardening in the GIs, but the hardening effect decreases with the grain size due to the increasing absorption of defects by GBs. Meanwhile, the absorbed defects would make the GBs softer than the unirradiated case. (ii) There exists a critical grain size for irradiated NC metals, which separates the grain size into the irradiation hardening dominant region (above the critical size) and irradiation softening dominant region (below the critical size). (iii) The distribution of grain size has a significant influence on the mechanical behaviours of both irradiated and unirradiated NCs. The proposed model can offer a valid theoretical foundation to study the irradiation effect on NC materials.

  11. Fractionated total body irradiation for metastatic neuroblastoma

    SciTech Connect

    Kun, L.E.; Casper, J.T.; Kline, R.W.; Piaskowski, V.D.

    1981-11-01

    Twelve patients over one year old with neuroblastoma (NBL) metastatic to bone and bone marrow entered a study of adjuvant low-dose, fractionated total body irradiation (TBI). Six children who achieved a ''complete clinical response'' following chemotherapy (cyclophosphamide and adriamycin) and surgical resection of the abdominal primary received TBI (10 rad/fraction to totals of 100-120 rad/10-12 fx/12-25 days). Two children received concurrent local irradiation for residual abdominal tumor. The intervals from cessation of chemotherapy to documented progression ranged from 2-16 months, not substatially different from patients receiving similar chemotherapy and surgery without TBI. Three additional children with progressive NBL received similar TBI (80-120 rad/8-12 fx) without objective response.

  12. Laryngeal acinic cell carcinoma following thyroid irradiation

    SciTech Connect

    Reibel, J.F.; McLean, W.C.; Cantrell, R.W.

    1981-01-01

    Only three examples of acinic cell carcinoma of the larynx or trachea are found in the recent literature. A case of acinic cell carcinoma of the subglottic larynx and trachea was diagnosed and treated at the University of Virginia Medical Center. To our knowledge this is the first such case with a prior history of radiation to the neck. The patient is a 56-year-old woman who was irradiated for hyperthyroidism 46 years ago. When seen she also had parathyroid hyperplasia and multiple thyroid adenomas, conditions that frequently follow irradiation of the thyroid in children. These findings in this case support the concept that radiation may be responsible for inducing this tumor, which otherwise rarely occurs in this location. The use of electron microscopy was extremely useful in the diagnosis of this tumor. She was treated with total laryngectomy and right neck dissection and is now free of disease one year after surgery.

  13. Spectral measurements of asymmetrically irradiated capsule backlighters

    NASA Astrophysics Data System (ADS)

    Keiter, P. A.; Drake, R. P.

    2016-11-01

    Capsule backlighters provide a quasi-continuum x-ray spectrum over a wide range of photon energies [J. F. Hansen et al., Rev. Sci. Instrum. 79, 013504 (2008)]. Ideally one irradiates the capsule backlighter symmetrically, however, in complex experimental geometries, this is not always possible. In recent experiments we irradiated capsule backlighters asymmetrically and measured the x-ray spectrum from multiple directions. We will present time-integrated spectra over the photon energy range of 2-13 keV and time-resolved spectra over the photon energy range of 2-3 keV. We will compare the spectra from different lines of sight to determine if the laser asymmetry results in an angular dependence in the x-ray emission.

  14. Spectral measurements of asymmetrically irradiated capsule backlighters

    DOE PAGES

    Keiter, P. A.; Drake, R. P.

    2016-09-09

    Capsule backlighters provide a quasi-continuum x-ray spectrum over a wide range of photon energies. Ideally one irradiates the capsule backlighter symmetrically, however, in complex experimental geometries, this is not always possible. In recent experiments we irradiated capsule backlighters asymmetrically and measured the x-ray spectrum from multiple directions. We will present time-integrated spectra over the photon energy range of ~2-13 keV and time-resolved spectra over the photon energy range of ~2-3 keV. Lastly, we will compare the spectra from different lines of sight to determine if the laser asymmetry results in an angular dependence in the x-ray emission.

  15. Membrane Protein Crystallization Using Laser Irradiation

    NASA Astrophysics Data System (ADS)

    Adachi, Hiroaki; Murakami, Satoshi; Niino, Ai; Matsumura, Hiroyoshi; Takano, Kazufumi; Inoue, Tsuyoshi; Mori, Yusuke; Yamaguchi, Akihito; Sasaki, Takatomo

    2004-10-01

    We demonstrate the crystallization of a membrane protein using femtosecond laser irradiation. This method, which we call the laser irradiated growth technique (LIGHT), is useful for producing AcrB crystals in a solution of low supersaturation range. LIGHT is characterized by reduced nucleation times. This feature is important for crystallizing membrane proteins because of their labile properties when solubilized as protein-detergent micelles. Using LIGHT, high-quality crystals of a membrane transporter protein, AcrB, were obtained. The resulting crystals were found to be of sufficiently high resolution for X-ray diffraction. The results reported here indicate that LIGHT is a powerful tool for membrane protein crystallization, as well as for the growth of soluble proteins.

  16. Neutron irradiation induced amorphization of silicon carbide

    SciTech Connect

    Snead, L.L.; Hay, J.C.

    1998-09-01

    This paper provides the first known observation of silicon carbide fully amorphized under neutron irradiation. Both high purity single crystal hcp and high purity, highly faulted (cubic) chemically vapor deposited (CVD) SiC were irradiated at approximately 60 C to a total fast neutron fluence of 2.6 {times} 10{sup 25} n/m{sup 2}. Amorphization was seen in both materials, as evidenced by TEM, electron diffraction, and x-ray diffraction techniques. Physical properties for the amorphized single crystal material are reported including large changes in density ({minus}10.8%), elastic modulus as measured using a nanoindentation technique ({minus}45%), hardness as measured by nanoindentation ({minus}45%), and standard Vickers hardness ({minus}24%). Similar property changes are observed for the critical temperature for amorphization at this neutron dose and flux, above which amorphization is not possible, is estimated to be greater than 130 C.

  17. Titanium implants in irradiated dog mandibles

    SciTech Connect

    Schweiger, J.W. )

    1989-08-01

    The use of osseointegrated titanium implants has been a great benefit to selected cancer patients who otherwise would not be able to wear conventional and/or maxillofacial prostheses. Cognizant of the risk of osteoradionecrosis, we used an animal model to seek experimental evidence for successful osseointegration in bone irradiated to tumoricidal levels. Five healthy male beagle dogs received 60 gray to a previously edentulated and healed area of the right hemimandible. The left hemimandible was kept as a nonirradiated control. After 9 months, titanium implants were placed and allowed an additional 5 1/2 months to osseointegrate. At that time, block specimens were obtained, radiographed, photographed, and analyzed histologically. Although statistical significance cannot be attached to the results, osseointegration was achieved in half of the irradiated specimens.

  18. UVA system for human cornea irradiation

    NASA Astrophysics Data System (ADS)

    Pereira, Fernando R. A.; Stefani, Mario; Otoboni, José A.; Richter, Eduardo H.; Rossi, Giuliano; Mota, Alessandro D.; Ventura, Liliane

    2009-02-01

    According to recent studies, an increase in corneal stiffness is a promising alternative for avoiding ectasias and for stagnating keratoconus of grades 1 and 2. The clinical treatment consists essentially of instilling Riboflavin (vitamin B2), in the cornea and then irradiating the corneal tissue, with UVA (365nm) radiation at 3mW/cm2 for 30min. This procedure provides collagen cross-linking in the corneal surface, increasing its stiffness. This work presents a system for UVA irradiation of the corneas at a peak wavelength of 365nm with adjustable power up to 5mW. The system has closed loop electronics to control the emitted power with 20% precision from the sated power output. The system is a prototype for performing corneal cross-linking and has been clinically tested. The closed loop electronics is a differential from the equipments available on the market.

  19. Sublethal irradiation promotes invasiveness of neuroblastoma cells

    SciTech Connect

    Schweigerer, Lothar; Rave-Fraenk, Margret; Schmidberger, Heinz; Hecht, Monica . E-mail: monica.hecht@med.uni-goettingen.de

    2005-05-13

    Neuroblastoma is the most frequent extracranial solid tumour of childhood. Despite multiple clinical efforts, clinical outcome has remained poor. Neuroblastoma is considered to be radiosensitive, but some clinical studies including the German trial NB90 failed to show a clinical benefit of radiation therapy. The mechanisms underlying this apparent discrepancy are still unclear. We have therefore investigated the effects of radiation on neuroblastoma cell behaviour in vitro. We show that sublethal doses of irradiation up-regulated the expression of the hepatocyte growth factor (HGF) and its receptor c-Met in some neuroblastoma cell lines. The increase in HGF/c-Met expression was correlated with enhanced invasiveness and activation of proteases degrading the extracellular matrix. Thus, irradiation at sublethal doses may promote the metastatic dissemination of neuroblastoma cells through activating the HGF/c-Met pathway and triggering matrix degradation.

  20. Nanohardness and brittleness of irradiated spinel ceramics

    NASA Astrophysics Data System (ADS)

    Jagielski, J.; Aubert, P.; Maciejak, O.; Piatkowska, A.; Labdi, S.; Jozwik-Biala, I.; Jozwik, P.; Wajler, A.

    2012-09-01

    The influence of the size of crystalline regions on mechanical properties of irradiated oxides has been studied using magnesium aluminate spinel MgAl2O4. The samples characterized by different dimensions of crystalline domains, from sintered ceramics with grains of few micrometers in size up to single crystals, were used in the experiments. The samples were irradiated at room temperature with 320 keV Ar2+ ions up to fluences reaching 5 × 1016 cm-2. Nanomechanical properties were measured by using a nanoindentation technique and the resistance to crack formation by measurement of the total crack lengths made by Vickers indenter. The results revealed: correlation of nanohardness with accumulated damage, radiation-induced hardness increase in grain-boundary region and significant improvement of material resistance to crack formation.

  1. Stress relaxation of vitreous silica on irradiation

    SciTech Connect

    Primak, W.

    1982-11-01

    The radiation-induced stress relaxation which is observed on ion bombardment of vitreous silica is described as a viscoelastic behavior in which the apparent viscosity is reduced to approx.10/sup 14/ Poise during irradiation and then increases rapidly by 4 or 5 orders of magnitude on cessation or interruption of irradiation. The bombarded layer appears to possess a viscosity approx.10/sup 19/ Poise, lower than would be expected for normal vitreous silica. On electron bombardment the viscosity is also reduced, but not as greatly as an ion bombardment, yet sufficiently to result in the whole radiation-induced volume contraction being realized perpendicularly to the surface, as has been found for ion bombardment. The maximum elastic stored energy which can be realized is but a fraction of a calorie per gram, hence the reported values of 200 cal/g would seem to be associated with the fragmentation of the network responsible for the reduced viscosity.

  2. Stored energy in irradiated silicon carbide

    SciTech Connect

    Snead, L.L.; Burchell, T.D.

    1997-04-01

    This report presents a short review of the phenomenon of Wigner stored energy release from irradiated graphite and discusses it in relation to neutron irradiation of silicon carbide. A single published work in the area of stored energy release in SiC is reviewed and the results are discussed. It appears from this previous work that because the combination of the comparatively high specific heat of SiC and distribution in activation energies for recombining defects, the stored energy release of SiC should only be a problem at temperatures lower than those considered for fusion devices. The conclusion of this preliminary review is that the stored energy release in SiC will not be sufficient to cause catastrophic heating in fusion reactor components, though further study would be desirable.

  3. Prospects for Irradiation in Cellulosic Ethanol Production

    PubMed Central

    Saini, Anita; Aggarwal, Neeraj K.; Sharma, Anuja; Yadav, Anita

    2015-01-01

    Second generation bioethanol production technology relies on lignocellulosic biomass composed of hemicelluloses, celluloses, and lignin components. Cellulose and hemicellulose are sources of fermentable sugars. But the structural characteristics of lignocelluloses pose hindrance to the conversion of these sugar polysaccharides into ethanol. The process of ethanol production, therefore, involves an expensive and energy intensive step of pretreatment, which reduces the recalcitrance of lignocellulose and makes feedstock more susceptible to saccharification. Various physical, chemical, biological, or combined methods are employed to pretreat lignocelluloses. Irradiation is one of the common and promising physical methods of pretreatment, which involves ultrasonic waves, microwaves, γ-rays, and electron beam. Irradiation is also known to enhance the effect of saccharification. This review explains the role of different radiations in the production of cellulosic ethanol. PMID:26839707

  4. Quantification of biologically effective environmental UV irradiance

    NASA Astrophysics Data System (ADS)

    Horneck, G.

    To determine the impact of environmental UV radiation on human health and ecosystems demands monitoring systems that weight the spectral irradiance according to the biological responses under consideration. In general, there are three different approaches to quantify a biologically effective solar irradiance: (i) weighted spectroradiometry where the biologically weighted radiometric quantities are derived from spectral data by multiplication with an action spectrum of a relevant photobiological reaction, e.g. erythema, DNA damage, skin cancer, reduced productivity of terrestrial plants and aquatic foodweb; (ii) wavelength integrating chemical-based or physical dosimetric systems with spectral sensitivities similar to a biological response curve; and (iii) biological dosimeters that directly weight the incident UV components of sunlight in relation to the effectiveness of the different wavelengths and to interactions between them. Most biological dosimeters, such as bacteria, bacteriophages, or biomolecules, are based on the UV sensitivity of DNA. If precisely characterized, biological dosimeters are applicable as field and personal dosimeters.

  5. Solar Irradiance, Plage and SOHO UV Images

    NASA Astrophysics Data System (ADS)

    Lopresto, James C.; Manross, Kevin

    1996-05-01

    Calcium K and H alpha plage and sunspot area have been monitored using Big Bear Observatory images on the INTERNET since November of 1992. The purpose of the project is to determine the correlation of changing plage area and solar irradiance changes. We also monitor changes in the K2 spec- tral index provided daily from Sacramento Peak. With the recent launching of the SOHO satellite, we are able to monitor the plage in the He II 304 Angstroms UV image. This image is near the top of the chromosphere nar or just under the transition region. The images show limb brightening as expected. Since it is widely believed that short time scale changes in the UV may be the dominant cause for low amplitude solar irradiance changes, the comparison of the "plage" ara in these UV images to those in conventional visible images should prove instructive.

  6. Cadmium Nanowire Formation Induced by Ion Irradiation

    SciTech Connect

    Jiang, Weilin; Weber, William J.; Wang, Chong M.; Young, James S.; Boatner, Lynn A.; Lian, Jie; Wang, Lumin; Ewing, Rodney C.

    2005-07-04

    One-dimensional nanostructures, such as nanowires, of semiconductors and metals are of great technological interest due to their potential for many advanced technology applications. Utilization of these materials versus their bulk counterparts will not only allow for device miniaturisation, but also may improve device performance or create new functions. Here we report a novel method for the synthesis of crystalline Cd-nanowires without involving either templates or a “seeded” structure. Ion irradiation at low temperatures (≤ 295 K) has been used to induce material decomposition and phase segregation in a cadmium niobate pyrochlore (Cd2Nb2O7) wafer. During the formation and rupture of the gas-filled blisters in the material, soft metallic Cd is extruded/extracted as nanowires through pores in the exfoliated layer. The entire process may be readily controlled by changing the ion irradiation conditions (e.g., ion species, dose and energy) with minimal thermal constraints.

  7. Long-term effects of orbital irradiation

    SciTech Connect

    Guyuron, B.; Dagys, A.P.; Munro, I.R.

    1987-11-01

    This retrospective study is a review of 18 patients who received radiotherapy to the orbit between the ages of 1 month and 10 years. Patients were followed for 7-21 years in an attempt to define the effects of orbital irradiation on a growing child. None of the patients in the study was spared injurious effects on soft tissue or bone, but soft tissue appeared to be more vulnerable to radiation than bone. Orbital irradiation caused soft tissue deficits of the upper face in 100% of the patients. Sixty-seven percent of patients had soft tissue deformities of the midface, and 13% had soft tissue deformities of the lower face. Bony deficits were found in the upper face in 67% of the patients, the midface in 50%, and the lower face in 6%. This study found no correlation between age and time of radiotherapy on the effects of facial growth.

  8. Raman spectroscopy of ion-irradiated astrophysically relevant materials

    NASA Astrophysics Data System (ADS)

    Baratta, G. A.; Brunetto, R.; Leto, G.; Palumbo, M. E.; Spinella, F.; Strazzulla, G.

    Solid objects in space (interstellar grains, comets, interplanetary dust particles, etc.) are continuously exposed to energetic processes, such as cosmic ion irradiation, that influence their evolution. In this paper we present an experimental study, carried out by Raman spectroscopy, of the effects induced by ion irradiation on frozen ices and refractory materials. If the irradiated ice mixture contains a relevant amount of carbon atoms, the ice is converted into an organic residue (stable at room temperature), which at high irradiation dose evolves toward a hydrogenated amorphous carbon. Here we show that material similar to that produced in the laboratory by ion irradiation of frozen ice mixtures and refractory materials can be formed in space by cosmic ion irradiation. This finding has been recently confirmed by the Stardust mission, which revealed in some of the cometary particles collected in space and returned to earth carbonaceous materials that have been processed by cosmic ion irradiation.

  9. Identification of gamma-irradiated papaya, melon and watermelon

    NASA Astrophysics Data System (ADS)

    Marín-Huachaca, Nélida S.; Mancini-Filho, Jorge; Delincée, Henry; Villavicencio, Anna Lúcia C. H.

    2004-09-01

    Ionizing radiation can be used to control spoilage microorganisms and to increase the shelf life of fresh fruits and vegetables in replacement for the treatment with chemical fumigants. In order to enforce labelling regulations, methods for detecting the irradiation treatment directly in the produce are required. Recently, a number of detection methods for irradiated food have been adopted by the Codex Comission. A rapid screening method for qualitative detection of irradiation is the DNA Comet Assay. The applicability of the DNA Comet Assay for distinguishing irradiated papaya, melon, and watermelon was evaluated. The samples were treated in a 60Co facility at dose levels of 0.0, 0.5, 0.75, and 1.0kGy. The irradiated samples showed typical DNA fragmentation whereas cells from non-irradiated ones appeared intact. In addition to the DNA Comet Assay also the half-embryo test was applied in melon and watermelon to detect the irradiation treatment.

  10. Low Dose Food Irradiation at Natick

    DTIC Science & Technology

    1977-06-01

    activity, titratable acidity, pH, ash, protein, and moisture content), dough and baking characteristics (bread scores, rheological and alpha-amylase...on the vitamin content in the irradiated flour or in the bread made from the 1 3See footnote 5 15 flour (Tables 10,11). Farinographs, dough ...sometimes sour , replaced it. The appearance of the nonirradiated chicken showed no discoloration up to about 8 days in storage, after which a dull

  11. Post irradiation examination of thermal reactor fuels

    NASA Astrophysics Data System (ADS)

    Sah, D. N.; Viswanathan, U. K.; Ramadasan, E.; Unnikrishnan, K.; Anantharaman, S.

    2008-12-01

    The post irradiation examination (PIE) facility at the Bhabha Atomic Research Centre (BARC) has been in operation for more than three decades. Over these years this facility has been utilized for examination of experimental fuel pins and fuels from commercial power reactors operating in India. In a program to assess the performance of (U,Pu)O 2 MOX fuel prior to its introduction in commercial reactors, three experimental MOX fuel clusters irradiated in the pressurized water loop (PWL) of CIRUS up to burnup of 16 000 MWd/tU were examined. Fission gas release from these pins was measured by puncture test. Some of these fuel pins in the cluster contained controlled porosity pellets, low temperature sintered (LTS) pellets, large grain size pellets and annular pellets. PIE has also been carried out on natural UO 2 fuel bundles from Indian PHWRs, which included two high burnup (˜15 000 MWd/tU) bundles. Salient investigations carried out consisted of visual examination, leak testing, axial gamma scanning, fission gas analysis, microstructural examination of fuel and cladding, β, γ autoradiography of the fuel cross-section and fuel central temperature estimation from restructuring. A ThO 2 fuel bundle irradiated in Kakrapar Atomic Power Station (KAPS) up to a nominal fuel burnup of ˜11 000 MWd/tTh was also examined to evaluate its in-pile performance. The performance of the BWR fuel pins of Tarapur Atomic Power Stations (TAPS) was earlier assessed by carrying out PIE on 18 fuel elements selected from eight fuel assemblies irradiated in the two reactors. The burnup of these fuel elements varied from 5000 to 29 000 MWd/tU. This paper provides a brief review of some of the fuels examined and the results obtained on the performance of natural UO 2, enriched UO 2, MOX, and ThO 2 fuels.

  12. Total lymphoid irradiation for multiple sclerosis

    SciTech Connect

    Devereux, C.K.; Vidaver, R.; Hafstein, M.P.; Zito, G.; Troiano, R.; Dowling, P.C.; Cook, S.D.

    1988-01-01

    Although chemical immunosuppression has been shown to benefit patients with chronic progressive multiple sclerosis (MS), it appears that chemotherapy has an appreciable oncogenic potential in patients with multiple sclerosis. Accordingly, we developed a modified total lymphoid irradiation (TLI) regimen designed to reduce toxicity and applied it to a randomized double blind trial of TLI or sham irradiation in MS. Standard TLI regimens were modified to reduce dose to 1,980 rad, lowering the superior mantle margin to midway between the thyroid cartilage and angle of the mandible (to avert xerostomia) and the lower margin of the mantle field to the inferior margin of L1 (to reduce gastrointestinal toxicity by dividing abdominal radiation between mantle and inverted Y), limiting spinal cord dose to 1,000 rad by custom-made spine blocks in the mantle and upper 2 cm of inverted Y fields, and also protecting the left kidney even if part of the spleen were shielded. Clinical efficacy was documented by the less frequent functional scale deterioration of 20 TLI treated patients with chronic progressive MS compared to to 20 sham-irradiated progressive MS patients after 12 months (16% versus 55%, p less than 0.03), 18 months (28% versus 63%, p less than 0.03), and 24 months (44% versus 74%, N.S.). Therapeutic benefit during 3 years follow-up was related to the reduction in lymphocyte count 3 months post-irradiation (p less than 0.02). Toxicity was generally mild and transient, with no instance of xerostomia, pericarditis, herpes zoster, or need to terminate treatment in TLI patients. However, menopause was induced in 2 patients and staphylococcal pneumonia in one.

  13. Adjustable compensators for whole-brain irradiation.

    PubMed

    Lerch, I A; Newall, J

    1979-02-01

    A compensator for use in irradiating the whole brain with parellel opposed lateral fields was made from a stack of thin tempered aluminum plates. This configuration gives a wide latitude of degrees of compensation and can accommodate a broad range of head sizes. Dosimetry studies indicate that overcompensation may be desirable to reduce the dose to the mid-coronal plane of the skull and scalp without seriously affecting the dose uniformity in the treatment volume.

  14. Surface changes of implants after laser irradiation

    NASA Astrophysics Data System (ADS)

    Rechmann, Peter; Sadegh, Hamid M. M.; Goldin, Dan S.; Hennig, Thomas

    1999-05-01

    Periimplantitis is one of the major factors for the loss of dental implants. Due to the minor defense ability of the tissue surrounding the implant compared to natural teeth treatment of periimplantitis in the early stage is very important. Reducing bacteria with a laser might be the most successful step in therapy of periimplantitis. Aim of the study was to observe changes in surface morphology of seven different implants after irradiation with three different lasers. Two kinds of flat round samles were prepared by the manufacturers either identical to the body surface or to the cervical area of the corresponding implants. The samples were irradiated using different power settings. The lasers used were a CO2 laser (Uni Laser 450P, ASAH Medico Denmark; fiber guided, wavelength 10.6 μm, max. average power 8.3 W, "soft-pulse" and cw) an Er:YAG laser (KaVo Key Laser II, wavelength 2.94 μm, pulse duration 250-500μs, pulse energy 60-500 mJ, pulse repetition rate 1-15 Hz, focus diameter 620 μm, air-water cooling; Biberach, Germany; a frequency doubled Alexandrite laser (laboratory prototype, q-switched, fiber guided, wavelength 377 nm, pulse duration 1 μs, pulse repetition rate 30 Hz, water cooling). After irradiation the implant surfaces were investigated with a Scanning Electron Microscope. Ablation thresholds were determined. After CO2 laser irradiation no changes in surface morphology were observed whereas using the pulsed Er:YAG laser or frequency doubled Alexandrite laser even at low energies loss of integrity or melting of the surface was observed. The changes in surface morphology seem to depend very strongly on the type of surface coating.

  15. Metal fuel manufacturing and irradiation performance

    SciTech Connect

    Pedersen, D.R.; Walters, L.C.

    1992-01-01

    The advances in metal fuel by the Integral Fast Reactor Program at Argonne National Laboratory are the subject of this paper. The Integral Fast Reactor (IFR) is an advanced liquid-metal-cooled reactor concept being developed at Argonne National Laboratory. The advances stressed in the paper include fuel irradiation performance, and improved passive safety. The goals and the safety philosophy of the Integral Fast Reactor Program are stressed.

  16. Metal fuel manufacturing and irradiation performance

    SciTech Connect

    Pedersen, D.R.; Walters, L.C.

    1992-06-01

    The advances in metal fuel by the Integral Fast Reactor Program at Argonne National Laboratory are the subject of this paper. The Integral Fast Reactor (IFR) is an advanced liquid-metal-cooled reactor concept being developed at Argonne National Laboratory. The advances stressed in the paper include fuel irradiation performance, and improved passive safety. The goals and the safety philosophy of the Integral Fast Reactor Program are stressed.

  17. Antitumor Immunity Induced after α Irradiation123

    PubMed Central

    Gorin, Jean-Baptiste; Ménager, Jérémie; Gouard, Sébastien; Maurel, Catherine; Guilloux, Yannick; Faivre-Chauvet, Alain; Morgenstern, Alfred; Bruchertseifer, Frank; Chérel, Michel; Davodeau, François; Gaschet, Joëlle

    2014-01-01

    Radioimmunotherapy (RIT) is a therapeutic modality that allows delivering of ionizing radiation directly to targeted cancer cells. Conventional RIT uses β-emitting radioisotopes, but recently, a growing interest has emerged for the clinical development of α particles. α emitters are ideal for killing isolated or small clusters of tumor cells, thanks to their specific characteristics (high linear energy transfer and short path in the tissue), and their effect is less dependent on dose rate, tissue oxygenation, or cell cycle status than γ and X rays. Several studies have been performed to describe α emitter radiobiology and cell death mechanisms induced after α irradiation. But so far, no investigation has been undertaken to analyze the impact of α particles on the immune system, when several studies have shown that external irradiation, using γ and X rays, can foster an antitumor immune response. Therefore, we decided to evaluate the immunogenicity of murine adenocarcinoma MC-38 after bismuth-213 (213Bi) irradiation using a vaccination approach. In vivo studies performed in immunocompetent C57Bl/6 mice induced a protective antitumor response that is mediated by tumor-specific T cells. The molecular mechanisms potentially involved in the activation of adaptative immunity were also investigated by in vitro studies. We observed that 213Bi-treated MC-38 cells release “danger signals” and activate dendritic cells. Our results demonstrate that α irradiation can stimulate adaptive immunity, elicits an efficient antitumor protection, and therefore is an immunogenic cell death inducer, which provides an attractive complement to its direct cytolytic effect on tumor cells. PMID:24862758

  18. Histologic changes in previously irradiated thyroid glands

    SciTech Connect

    Valdiserri, R.O.; Borochovitz, D.

    1980-03-01

    Thyroid tissue from 90 patients with a history of therapeutic irradiation to the head and neck in childhood and adolescence was examined microscopically. In addition to the well-known observation that these individuals have an increased incidence of primary thyroid carcinoma, it was also demonstrated that they have an increased incidence of benign histologic changes. These changes represent a spectrum from nonspecific hyperplastic lesions to benign neoplasis and thyroidltis.

  19. Electron Irradiation of Light Emitting Diodes.

    DTIC Science & Technology

    1984-12-01

    the present experiment were fabricated by liquid phase epitaxy (LPE) or vapor phase epitaxy (VPE). Millea and Aukerman [Ref. 5 and 6] studied electron...neutron induced damage. They and Millea and Aukerman [Ref. 6] observed the absence of bias induced recovery in neutron irradiated LEDs. This is in...Herrick, D., J. Applied Phys., 41, 3783, 1970. 4. Stanley, A.G., IEEE Trans. Nucl. Sci., NS-17, 239, 1970. 5. Millea, M.F., and Aukerman , L.W., J

  20. Mechanical Cutting of Irradiated Reactor Internal Components

    SciTech Connect

    Anderson, M.G.; Fennema, J.A.

    2007-07-01

    This paper discusses the use of mechanical cutting methods to volume reduce and package irradiated reactor internal components. The recent completion of the removal of the Reactor Vessel Internals (RVI) from within the Sacramento Municipal Utility District's (SMUD) Rancho Seco Nuclear Power Plant demonstrates that unlike previous methods used for similar projects, mechanical cutting minimizes exposure to workers, costly water cleanup, and excessive secondary waste generation. (authors)

  1. Optical Properties of Irradiated Topaz Crystals

    NASA Astrophysics Data System (ADS)

    Skvortsova, V.; Mironova-Ulmane, N.; Trinkler, L.

    2015-04-01

    The results of an investigation of UV-Visible absorption and photoluminescence spectra of colorless topaz before and after neutron irradiation, natural blue topaz from Ukraine, and yellow topaz are presented. We assume that the absorption band ∼ 620 nm and broad emission band 300-700 nm in topaz crystals are associated with exchange interaction between a radiation defect (anion vacancies, which capture one or two electrons) and impurity ions Cr3+, Fe3+ and Mn2+.

  2. Irradiation Products On Dwarf Planet Makemake

    NASA Astrophysics Data System (ADS)

    Brown, M. E.; Schaller, E. L.; Blake, G. A.

    2015-03-01

    The dark, reddish tinged surfaces of icy bodies in the outer solar system are usually attributed to the long term irradiation of simple hydrocarbons leading to the breaking of C-H bonds, loss of hydrogen, and the production of long carbon chains. While the simple hydrocarbon methane is stable and detected on the most massive bodies in the Kuiper Belt, evidence of active irradiation chemistry is scant except for the presence of ethane on methane-rich Makemake and the possible detections of ethane on more methane-poor Pluto and Quaoar. We have obtained deep high signal-to-noise spectra of Makemake from 1.4 to 2.5 μm in an attempt to trace the radiation chemistry in the outer solar system beyond the initial ethane formation. We present the first astrophysical detection of solid ethylene and evidence for acetylene and high-mass alkanes—all expected products of the continued irradiation of methane, and use these species to map the chemical pathway from methane to long-chain hydrocarbons.

  3. Advanced lymphosarcoma treated by total body irradiation.

    PubMed Central

    Chaffey, J. T.; Rosenthal, D. S.; Pinkus, F.; Hellman, S.

    1975-01-01

    Twenty-five cases of clinical Stage III and Stage IV lymphosarcoma primarily treated by total body irradiation (TBI) are reported. Fifteen cases demonstrated nodular histology and 10 demonstrated diffuse histology by the Rappaport criteria. Treatments were 15 rad given twice weekly, calculated to midpelvis, to a total dose of 150 rad. Toxicity was confined to thrombocytopenia, one-third of patients requiring interruptions in the treatment course to allow platelet count recovery. Five patients had additional local irradiation. Complete responses were seen in 80% of patients and partial responses in 20%. Sixteen patients (64%) have been in continuous, unmaintained remission since treatments for variable periods to 39 months. Of 9 patients with clinically recurrent disease, 3 received further TBI and are in remission, 3 are in remission on chemotherapy, one patient has died, failing on all therapy, and 2 have not been treated. One patient died of pneumonia at 12 months, without clinical evidence of disease. Overall, actuarial survival is 87% at 2 years and compares well with survival in a sequential combination drug treated group of patients matched for age, sex, and histology, though differences are not statistically significant in these small groups. Total body irradiation is an effective systemic agent in the management of advanced lymphosarcoma and should be considered in treating this disease. PMID:810155

  4. Irradiation Environment of the Materials Test Station

    SciTech Connect

    Pitcher, Eric John

    2012-06-21

    Conceptual design of the proposed Materials Test Station (MTS) at the Los Alamos Neutron Science Center (LANSCE) is now complete. The principal mission is the irradiation testing of advanced fuels and materials for fast-spectrum nuclear reactor applications. The neutron spectrum in the fuel irradiation region of MTS is sufficiently close to that of fast reactor that MTS can match the fast reactor fuel centerline temperature and temperature profile across a fuel pellet. This is an important characteristic since temperature and temperature gradients drive many phenomena related to fuel performance, such as phase stability, stoichiometry, and fission product transport. The MTS irradiation environment is also suitable in many respects for fusion materials testing. In particular, the rate of helium production relative to atomic displacements at the peak flux position in MTS matches well that of fusion reactor first wall. Nuclear transmutation of the elemental composition of the fusion alloy EUROFER97 in MTS is similar to that expected in the first wall of a fusion reactor.

  5. Electron Irradiation of Interstellar Ice Analogues

    NASA Astrophysics Data System (ADS)

    Nair, B. G.; Mason, N. J.

    2011-05-01

    Molecular synthesis in the Universe primarily occurs in the icy mantles on dust grains in dense interstellar dust clouds. The interaction of photons, electrons and cosmic rays with these ice mantles triggers complex chemical synthesis leading to the formation of complex molecules. Such molecular reactions can only be understood by systematic laboratory studies. In our experiments astrophysical environments are recreated in the laboratory using an ultra high vacuum chamber (UHV) capable of reaching pressures of the order of 10 -10 mBar containing a liquid helium cryostat capable of attaining a temperature of 20 K. Ice films are deposited on a ZnSe substrate (cooled by cryostat) by background deposition and irradiated with electrons of 1KeV energy. Chemical changes induced by electron irradiation were monitored by an infrared spectrometer. By varying the temperature, we also investigate the temperature dependence on the kinetics of the reactions. In this poster we will present the first results of electron irradiation of simple organic molecules like formamide (HCONH2) and allyl alcohol (CH2CHCH2OH).

  6. Local brain heavy ion irradiation induced Immunosuppression

    NASA Astrophysics Data System (ADS)

    Lei, Runhong; Deng, Yulin; Huiyang Zhu, Bitlife.; Zhao, Tuo; Wang, Hailong; Yu, Yingqi; Ma, Hong; Wang, Xiao; Zhuang, Fengyuan; Qing, Hong

    Purpose: To investigate the long term effect of acute local brain heavy ion irradiation on the peripheral immune system in rat model. Methodology: Only the brain of adult male Wistar rats were radiated by heavy ions at the dose of 15 Gy. One, two and three months after irradiation, thymus and spleen were analyzed by four ways. Tunel assay was performed to evaluate the percentage of apoptotic cells in thymus and spleen, level of Inflammatory cytokines (IL-2, IL-6, SSAO, and TNF-α) was detected by ELISA assay, the differentiation of thymus T lymphocyte subsets were measured by flow cytometry and the relative expression levels of genes related to thymus immune cell development were measured by using quantitative real-time PCR. Results: Thymus and spleen showed significant atrophy from one month to three months after irradiation. A high level of apoptosis in thymus and spleen were obtained and the latter was more vulnerable, also, high level of inflammatory cytokines were found. Genes (c-kit, Rag1, Rag2 and Sca1) related to thymus lymphocytes’ development were down-regulated. Conclusion: Local area radiation in the rat brain would cause the immunosuppression, especially, the losing of cell-mediated immune functions. In this model, radiation caused inflammation and then induced apoptosis of cells in the immune organs, which contributed to immunosuppression.

  7. Irradiation response and stability of nanoporous materials

    SciTech Connect

    Fu, Engang; Wang, Yongqiang; Serrano De Caro, Magdalena; Caro, Jose A.; Zepeda-Ruiz, L; Bringa, E.; Nastasi, Mike; Baldwin, Jon K.

    2012-08-28

    Nanoporous materials consist of a regular organic or inorganic framework supporting a regular, porous structure. Pores are by definition roughly in the nanometre range, that is between 0.2 nm and 100 nm. Nanoporous materials can be subdivided into 3 categories (IUPAC): (1) Microporous materials - 0.2-2 nm; (2) Mesoporous materials - 2-50 nm; and (3) Macroporous materials - 50-1000 nm. np-Au foams were successfully synthesized by de-alloying process. np-Au foams remain porous structure after Ne ion irradiation to 1 dpa. Stacking Fault Tetrahedra (SFTs) were observed in RT irradiated np-Au foams under the highest and intermediate fluxes, but not under the lowest flux. SFTs were not observed in LNT irradiated np-Au foams under all fluxes. The vacancy diffusivity in Au at RT is high enough so that the vacancies have enough time to agglomerate and then collapse to form SFTs. The high ion flux creates more damage per unit time; vacancies don't have enough time to diffuse or recombine. As a result, SFTs were formed at high ion fluxes.

  8. Polyethylene terephthalate degradation under reactor neutron irradiation

    NASA Astrophysics Data System (ADS)

    Chikaoui, K.; Izerrouken, M.; Djebara, M.; Abdesselam, M.

    2017-01-01

    This paper is devoted to study the defects generated by reactor neutron in polyethylene terephthalate (PET) films. The explored fast neutron fluence ranges from 2.02×1016 to 2.07×1018 n cm-2. The induced damages were investigated using ultraviolet-visible spectrophotometry (UV-vis), Fourier Transform Infrared spectrometry (FTIR) and X-ray diffraction (XRD). The UV-vis spectra show important changes indicating the degradation of the chemical structure and the creation of new chromophores. FTIR spectra reveal that the intensities of the different absorption bands decrease linearly under fast neutron irradiation. The internal reference band at 1410 cm-1 is used to follow the overall damage during irradiation. The 1342 cm-1 band corresponding to CH2 wagging of trans conformation of crystalline phase show a sharpe linear decrease as the fast neutrons fluence goes up. The creation of the monosubstituted benzene, investigated using the 1610 cm-1 band. It shows a linear increase with fast neutron fluence. It is found from XRD analysis that the diffraction peak (100) intensity is drastically reduced after irradiation at 2.02×1016 n cm-2.

  9. Recycling of irradiated high-density polyethylene

    NASA Astrophysics Data System (ADS)

    Navratil, J.; Manas, M.; Mizera, A.; Bednarik, M.; Stanek, M.; Danek, M.

    2015-01-01

    Radiation crosslinking of high-density polyethylene (HDPE) is a well-recognized modification of improving basic material characteristics. This research paper deals with the utilization of electron beam irradiated HDPE (HDPEx) after the end of its lifetime. Powder of recycled HDPEx (irradiation dose 165 kGy) was used as a filler into powder of virgin low-density polyethylene (LDPE) in concentrations ranging from 10% to 60%. The effect of the filler on processability and mechanical behavior of the resulting mixtures was investigated. The results indicate that the processability, as well as mechanical behavior, highly depends on the amount of the filler. Melt flow index dropped from 13.7 to 0.8 g/10 min comparing the lowest and the highest concentration; however, the higher shear rate the lower difference between each concentration. Toughness and hardness, on the other hand, grew with increasing addition of the recycled HDPEx. Elastic modulus increased from 254 to 450 MPa and material hardness increased from 53 to 59 ShD. These results indicate resolving the problem of further recycling of irradiated polymer materials while taking advantage of the improved mechanical properties.

  10. Hydrogen retention in ion irradiated steels

    SciTech Connect

    Hunn, J.D.; Lewis, M.B.; Lee, E.H.

    1998-11-01

    In the future 1--5 MW Spallation Neutron Source, target radiation damage will be accompanied by high levels of hydrogen and helium transmutation products. The authors have recently carried out investigations using simultaneous Fe/He,H multiple-ion implantations into 316 LN stainless steel between 50 and 350 C to simulate the type of radiation damage expected in spallation neutron sources. Hydrogen and helium were injected at appropriate energy and rate, while displacement damage was introduced by nuclear stopping of 3.5 MeV Fe{sup +}, 1 {micro}m below the surface. Nanoindentation measurements showed a cumulative increase in hardness as a result of hydrogen and helium injection over and above the hardness increase due to the displacement damage alone. TEM investigation indicated the presence of small bubbles of the injected gases in the irradiated area. In the current experiment, the retention of hydrogen in irradiated steel was studied in order to better understand its contribution to the observed hardening. To achieve this, the deuterium isotope ({sup 2}H) was injected in place of natural hydrogen ({sup 1}H) during the implantation. Trapped deuterium was then profiled, at room temperature, using the high cross-section nuclear resonance reaction with {sup 3}He. Results showed a surprisingly high concentration of deuterium to be retained in the irradiated steel at low temperature, especially in the presence of helium. There is indication that hydrogen retention at spallation neutron source relevant target temperatures may reach as high as 10%.

  11. The spectral irradiance of the moon

    USGS Publications Warehouse

    Kieffer, H.H.; Stone, T.C.

    2005-01-01

    Images of the Moon at 32 wavelengths from 350 to 2450 nm have been obtained from a dedicated observatory during the bright half of each month over a period of several years. The ultimate goal is to develop a spectral radiance model of the Moon with an angular resolution and radiometric accuracy appropriate for calibration of Earth-orbiting spacecraft. An empirical model of irradiance has been developed that treats phase and libration explicitly, with absolute scale founded on the spectra of the star Vega and returned Apollo samples. A selected set of 190 standard stars are observed regularly to provide nightly extinction correction and long-term calibration of the observations. The extinction model is wavelength-coupled and based on the absorption coefficients of a number of gases and aerosols. The empirical irradiance model has the same form at each wavelength, with 18 coefficients, eight of which are constant across wavelength, for a total of 328 coefficients. Over 1000 lunar observations are fitted at each wavelength; the average residual is less than 1%. The irradiance model is actively being used in lunar calibration of several spacecraft instruments and can track sensor response changes at the 0.1% level. ?? 2005. The American Astronomical Society. All rights reserved.

  12. Blue LED irradiation to hydration of skin

    NASA Astrophysics Data System (ADS)

    Menezes, Priscila F. C.; Requena, Michelle B.; Lizarelli, Rosane F., Z.; Bagnato, Vanderlei S.

    2015-06-01

    Blue LED system irradiation shows many important properties on skin as: bacterial decontamination, degradation of endogenous skin chromophores and biostimulation. In this clinical study we prove that the blue light improves the skin hydration. In the literature none authors reports this biological property on skin. Then this study aims to discuss the role of blue light in the skin hydration. Twenty patients were selected to this study with age between 25-35 years old and phototype I, II and III. A defined area from forearm was pre determined (A = 4.0 cm2). The study was randomized in two treatment groups using one blue light device (power of 5.3mW and irradiance of 10.8mW/cm2). The first treatment group was irradiated with 3J/cm2 (277seconds) and the second with 6J/cm2 (555 seconds). The skin hydration evaluations were done using a corneometer. The measurements were collected in 7, 14, 21 and 30 days, during the treatment. Statistical test of ANOVA, Tukey and T-Student were applied considering 5% of significance. In conclusion, both doses were able to improve the skin hydration; however, 6J/cm2 has kept this hydration for 30 days.

  13. NOTE: Validation of blood product irradiation doses

    NASA Astrophysics Data System (ADS)

    Cheung, T.; Butson, M.; Yu, P. K. N.

    2001-10-01

    Dosimetry of blood irradiation using x-ray beams on a medical linear accelerator has been studied to evaluate the accuracy of a diode detector and the delivery achievable. Variations in applied doses for a standard dual field 6 MV x-ray are measured with a commercial diode detector. Results show that the diode detector measured applied in vitro doses to within 5.4% (2 standard deviations (2 SD)) of those calculated with a collapsed-cone convolution treatment-planning computer for a sample of 100 blood irradiations. Experiments involving the packing procedure of the blood products in the blood box were performed. It was found that a large proportion of the variation in the predicted and measured dose was due to the compacting of the scatter material at the base of the blood box (over a 6 month period) producing a higher density below the blood than originally scanned; hence an overall reduction of delivered dose was observed. The diode measurements (which provide an immediate printout) are recommended in conjunction with a film dosimeter such as radiochromic film, which still provides a back-up dose monitor and a visual reminder that the blood has been irradiated. It is also recommended that the blood box be completely evacuated of all scatter material every month and the base be carefully repacked to provide uniform scatter material.

  14. Validation of blood product irradiation doses.

    PubMed

    Cheung, T; Butson, M; Yu, P K

    2001-10-01

    Dosimetry of blood irradiation using x-ray beams on a medical linear accelerator has been studied to evaluate the accuracy of a diode detector and the delivery achievable. Variations in applied doses for a standard dual field 6 MV x-ray are measured with a commercial diode detector. Results show that the diode detector measured applied in vitro doses to within 5.4% (2 standard deviations (2 SD)) of those calculated with a collapsed-cone convolution treatment-planning computer for a sample of 100 blood irradiations. Experiments involving the packing procedure of the blood products in the blood box were performed. It was found that a large proportion of the variation in the predicted and measured dose was due to the compacting of the scatter material at the base of the blood box (over a 6 month period) producing a higher density below the blood than originally scanned; hence an overall reduction of delivered dose was observed. The diode measurements (which provide an immediate printout) are recommended in conjunction with a film dosimeter such as radiochromic film, which still provides a back-up dose monitor and a visual reminder that the blood has been irradiated. It is also recommended that the blood box be completely evacuated of all scatter material every month and the base be carefully repacked to provide uniform scatter material.

  15. Protein Quality of Irradiated Brazilian Beans

    NASA Astrophysics Data System (ADS)

    Delincée, Henry; Villavicencio, Anna-Lucia C. H.; Mancini-Filho, Jorge

    1998-06-01

    Beans are a major source of dietary protein in Brazil. However, high losses due to insect infestation occur after each harvest. To combat these losses, radiation processing of beans offers promise as an alternative to chemical treatment, provided the nutritional quality of beans is not impaired by the radiation treatment. Conflicting results have been published about the effect of radiation on the biological value of legume proteins. Therefore, two varieties of Brazilian beans were studied: 1) Phaseolus vulgaris L., var. carioca and 2) Vigna unguiculata (L.) Walp, var. macaçar. The beans were irradiated with doses of 0, 0.5, 1.0, 2.5, 5.0 and 10 kGy. Since irradiated beans will be consumed after appropriate storage, the beans under study were stored for 6 months at ambient temperature. Protein quality was measured by a biological assay employing the nitrogen balance approach in weanling rats. The animals were fed with optimally cooked beans, which were the only source of protein (˜10%). Nitrogen contents of legumes, diets, animal urine and faeces were determined by Kjeldahl analysis. The indices for apparent protein quality: net protein utilisation, digestibility and biological value were not influenced by irradiation. Thus, radiation treatment of Brazilian beans offers considerable promise as an effective insect disinfection process, without impairing the biological quality of the valuable bean protein.

  16. Upgrade to the Birmingham Irradiation Facility

    NASA Astrophysics Data System (ADS)

    Dervan, P.; French, R.; Hodgson, P.; Marin-Reyes, H.; Parker, K.; Wilson, J.; Baca, M.

    2015-10-01

    The Birmingham Irradiation Facility was developed in 2013 at the University of Birmingham using the Medical Physics MC40 cyclotron. It can achieve High Luminosity LHC (HL-LHC) fluences of 1015 (1 MeV neutron equivalent (neq)) cm-2 in 80 s with proton beam currents of 1 μA and so can evaluate effectively the performance and durability of detector technologies and new components to be used for the HL-LHC. Irradiations of silicon sensors and passive materials can be carried out in a temperature controlled cold box which moves continuously through the homogenous beamspot. This movement is provided by a pre-configured XY-axis Cartesian robot scanning system. In 2014 the cooling system and cold box were upgraded from a recirculating glycol chiller system to a liquid nitrogen evaporative system. The new cooling system achieves a stable temperature of -50 °C in 30 min and aims to maintain sub-0 °C temperatures on the sensors during irradiations. This paper reviews the design, development, commissioning and performance of the new cooling system.

  17. Hodgkin's disease: thyroid dysfunction following external irradiation

    SciTech Connect

    Tamura, K.; Shimaoka, K.

    1981-01-01

    The thyroid gland is commonly included in the field of radiation therapy for patients with malignant lymphoma and with head and neck tumors. The radiation dose for malignant diseases varies considerably depending on the purpose of treatment and the institutional policies. A substantial number of these patients are developing subclinical and clinical hypothyroidism. The risk of developing hypothyroidism after a moderate radiation dose of 2000 to 4500 rads has been reported to be 10 to 20 percent. In addition, subclinical hypothyroidism is induced further in one third of the patients. There are also suggestions that external irradiation of the thyroid gland in patients with malignant lymphomas, as well as internal irradiation with radioiodine of the normal and hyperthyroid human thyroid glands, would induce elevations of serum antithyroid autoantibody titers. However, only a few cases of Graves disease following irradiation to the thyroid gland have been reported. We encountered a young woman who received radiation therapy to the mantle field for her Hodgkin's disease and developed hypothyroxinemia without overt signs and symptoms of hypothyroidism, followed by appearance of nodular goiter and then full-blown Graves disease.

  18. Multivariate Analysis of Solar Spectral Irradiance Measurements

    NASA Technical Reports Server (NTRS)

    Pilewskie, P.; Rabbette, M.

    2001-01-01

    Principal component analysis is used to characterize approximately 7000 downwelling solar irradiance spectra retrieved at the Southern Great Plains site during an Atmospheric Radiation Measurement (ARM) shortwave intensive operating period. This analysis technique has proven to be very effective in reducing a large set of variables into a much smaller set of independent variables while retaining the information content. It is used to determine the minimum number of parameters necessary to characterize atmospheric spectral irradiance or the dimensionality of atmospheric variability. It was found that well over 99% of the spectral information was contained in the first six mutually orthogonal linear combinations of the observed variables (flux at various wavelengths). Rotation of the principal components was effective in separating various components by their independent physical influences. The majority of the variability in the downwelling solar irradiance (380-1000 nm) was explained by the following fundamental atmospheric parameters (in order of their importance): cloud scattering, water vapor absorption, molecular scattering, and ozone absorption. In contrast to what has been proposed as a resolution to a clear-sky absorption anomaly, no unexpected gaseous absorption signature was found in any of the significant components.

  19. Analyzing UV-B narrowband solar irradiance: comparison with erythemal and vitamin D production irradiances.

    PubMed

    Sola, Yolanda; Lorente, Jerónimo; Ossó, Albert

    2012-12-05

    The heliotherapy and the phototherapy are mainly focused on taking benefit of the therapeutic effects of the ultraviolet (UV) irradiance on different skin diseases. The use of UV-B narrowband lamps, with emissions centered at 311 nm, has spread out among the dermatologist community because of its high therapeutic effect in comparison with its low erythema dose. For cloudless sun exposure, the balance of solar erythemal and solar narrowband (NB)-equivalent irradiances depends on several factors such as the solar zenith angle (SZA), the total ozone column (TOC) and the altitude. For SZA below 55°, the ratio of solar UV-B narrowband and erythemal irradiances increases with the SZA whereas the ratio of vitamin D production and erythemal irradiances decreases with the SZA with the maximum around midday. Furthermore, the solar NB ratio also increases with the TOC because the shorter wavelengths of the erythemal action spectrum are more affected by the ozone absorption processes. Considering the daily variations of the ratio between narrowband and erythemal irradiance, sun exposures avoiding midday hours are recommended in order to prevent negative side-effects. However to accumulate great NB doses and sufficient vitamin D in winter months is difficult because the time exposures may be longer than the day duration.

  20. METAPHIX-1 non destructive post irradiation examinations in the irradiated elements cell at Phenix

    SciTech Connect

    Breton, Laurent; Masson, M.; Garces, E.; Desjardins, S.; Fontaine, B.; Lacroix, B.; Martella, T.; Loubet, L.; Ohta, H.; Yokoo, T.; Ougier, M.; Glatz, J.P.

    2007-07-01

    Central Research Institute of Electric Power Industry (CRIEPI) has been developing minor actinide (MA) transmutation technology in homogeneous loading mode by use of metal fuel fast reactors in cooperation with Institute for Transuranium Elements (ITU) and Commissariat a l'Energie Atomique (CEA). Fast reactor metal fuel pins of Uranium- Plutonium-Zirconium (U-Pu-Zr) alloy containing 2 wt% MAs and 2 wt% rare earth elements (REs), 5 wt% MAs, and 5 wt% MAs and 5 wt% REs were irradiated in the PHENIX French fast reactor as METAPHIX experiments. In these METAPHIX experiments, three rigs each consisting of three metal fuel experimental pins and sixteen oxide fuel driver pins were irradiated. The target burnup of the three rigs is 2.4 at%, 7 at% and 11 at% which corresponds to 120, 360 and 600 equivalent full power days (EFPD) in terms of irradiation periods, respectively. The low burnup rig of 2.4 at%, METAPHIX-1, was discharged from the core in August 2004. After cooling, the non-destructive post irradiation examinations (PIEs) of the rig (visual examination, measurement of rig length and deformation) and of the metal fuel pins (visual examination, measurement of pin length and deformation, {gamma}-spectrometry and neutron radiography) were conducted in the Irradiated Elements Cell (IEC) at PHENIX. (authors)

  1. Plant responses to UV-B irradiation are modified by UV-A irradiation

    SciTech Connect

    Middleton, E.M.; Teramura, A.H. Univ. of Maryland, College Park )

    1993-06-01

    The increasing UV-B radiation (0.28-0.32 [mu]m) reaching the earth's surface is an important concern. Plant response in artificial UV-B irradiation studies has been difficult to assess, especially regarding photosynthetic pigments, because the fluorescent lamps also produce UV-A (0.32-0.40[mu]m) radiation which is involved with blue light in pigment synthesis. Both UV-A and UV-B irradiances were controlled in two glasshouse experiments conducted under relatively high PPFD (> 1300[mu]mol m[sup [minus]2] s[sup [minus]1]) at two biologically effective daily UV-B irradiances (10.7 and 14.1 kJ m[sup [minus]2]); UV-A irradiances were matched in Controls ([approximately]5, 9 kJ m[sup [minus]2]). Normal, chlorophyll-deficient, and flavonoid-deficient isolines of soybean cultivar, Clark, were utilized. Many growth/ pigment variables exhibited a statistically significant interaction between light quality and quantity: in general, UV-A radiation moderated the damaging effects of UV-B radiation. Regression analyses demonstrated that a single negative function related photosynthetic efficiency to carotenoid Content (r[sup 2] =0.73, P[le]0.001), implying a [open quotes]cost[close quotes] in maintaining carotenoids for photoprotection. A stomatal limitation to photosynthesis was verified and carotenoid content was correlated with UV-B absorbing compound levels, in UV-B irradiated plants.

  2. Survival after total body irradiation: Effects of irradiation of exteriorized small intestine. (Reannouncement with new availability information)

    SciTech Connect

    Vriesendorp, H.M.; Vigneulle, R.M.; Kitto, G.; Pelky, T.; Taylor, P.

    1993-12-31

    Rats receiving lethal irradiation to their exteriorized small intestine with pulsed 18 MVp bremsstrahlung radiation live about 4 days longer than rats receiving a dose of total-body irradiation (TBI) causing intestinal death. The LD50 for intestinal irradiation is approximately 6 Gy higher than the LD50 for intestinal death after TBI. Survival time after exteriorized intestinal irradiation can be decreased, by adding abdominal irradiation. Adding thoracic or pelvic irradiation does not alter survival time. Shielding of large intestine improves survival after irradiation of the rest of the abdomen while the small intestine is also shielded. The kinetics of histological changes in small intestinal tissues implicate the release of humoral factors after irradiation of the abdomen. Radiation injury develops faster in the first (proximal) 40 cm of the small intestine and is expressed predominantly as shortening in villus height. In the last (distal) 40 cm of the small intestine, the most pronounced radiation effect is a decrease in the number of crypts per millimeter. Irradiation (20 Gy) of the proximal small intestine causes 92 % mortality (median survival 10 days). Irradiation (20 Gy) of the distal small intestine causes 27% mortality (median survival > 30 days). In addition to depletion of crypt stem cells in the small intestine, other issues (humoral factors, irradiated subsection of the small intestine and shielding of the large intestine) appear to influence radiation-induced intestinal mortality.

  3. Methods for routine control of irradiated food: Determination of the irradiation status of shellfish by thermoluminescence analysis

    NASA Astrophysics Data System (ADS)

    Schreiber, G. A.; Hoffmann, A.; Helle, N.; Bögl, K. W.

    1994-06-01

    In some countries, clearance has been given for treating certain types of shellfish by ionizing radiation in order to increase the shelf-life and to reduce health hazards which might be caused by contaminating microorganisms. In the present study, thermoluminescence (TL) analysis was used to examine the irradiation status of shellfish products purchased from local suppliers. For analysis minerals were isolated from the guts of the animals. Although on none of the examined products an irradiation treatment prior to analysis could be shown, the results obtained on non-irradiated and irradiated products have revealed that irradiation within the commercially used dose range can clearly be detected. Already first glow TL intensities of minerald indicated irradiation treatments. Normalized TL signals of non-irradiated and irradiated samples were clearly separated. By calculation of differences of TL intensities and TL signals between non-irradiated and irradiated samples in dependency of integration temperature an optimized integration area for glow curves was determined. The result of this study agree well with results obtained by two large-scale intercomparisons between food control laboratories to detect irradiation treatment of spices and herbal products as well as of fruit and vegetables by TL analysis of contaminating minerals.

  4. The spectral irradiance traceability chain at PTB

    SciTech Connect

    Sperfeld, P.; Pape, S.; Nevas, S.

    2013-05-10

    Spectral irradiance is a fundamental radiometric unit. Its application to measurement results requires qualified traceability to basic units of the international system of units (Systeme international d'unites, SI). The Physikalisch-Technische Bundesanstalt (PTB) is amongst other national metrological institutes (NMIs) responsible for the realization, maintenance and dissemination of various radiometric and photometric units based on and traceable to national standards. The unit of spectral irradiance is realized and represented by a blackbody-radiator as the national primary standard of the PTB. Based on Planck's radiation law, the irradiance is calculated and realized for any wavelength taking into account the exact knowledge of the radiation temperature and the geometrical parameters. Using a double-monochromator-based spectroradiometer system, secondary standard lamps can be calibrated by direct comparison to the blackbody-radiator (substitution method). These secondary standard lamps are then used at the PTB to calibrate standard lamps of customers. The customers themselves use these so-called transfer standards to calibrate their working standard lamps. These working standards are then used to calibrate own spectroradiometers or sources. This rather complex calibration chain is a common procedural method that for the customers generally leads to satisfying measurement results on site. Nevertheless, the standard lamps in use have to fulfill highest requirements concerning stability and reproducibility. Only this allows achieving comparably low transfer measurement uncertainties, which occur at each calibration step. Thus, the PTB is constantly investigating the improvement and further development of transfer standards and measurement methods for various spectral regions. The realization and dissemination of the spectral irradiance using the blackbody-radiator at the PTB is accomplished with worldwide approved minimized measurement uncertainties confirmed by

  5. EFFECTS OF GAMMA IRRADIATION ON EPDM ELASTOMERS

    SciTech Connect

    Clark, E.

    2011-09-22

    Two formulations of EPDM elastomer, one substituting a UV stabilizer for the normal antioxidant in this polymer, and the other the normal formulation, were synthesized and samples of each were exposed to gamma irradiation in initially pure deuterium gas to compare their radiation stability. Stainless steel containers having rupture disks were designed for this task. After 130 MRad dose of cobalt-60 radiation in the SRNL Gamma Irradiation Facility, a significant amount of gas was created by radiolysis; however the composition indicated by mass spectroscopy indicated an unexpected increase in the total amount deuterium in both formulations. The irradiated samples retained their ductility in a bend test. No change of sample weight, dimensions, or density was observed. No change of the glass transition temperature as measured by dynamic mechanical analysis was observed, and most of the other dynamic mechanical properties remained unchanged. There appeared to be an increase in the storage modulus of the irradiated samples containing the UV stabilizer above the glass transition, which may indicate hardening of the material by radiation damage. Polymeric materials become damaged by exposure over time to ionizing radiation. Despite the limited lifetime, polymers have unique engineering material properties and polymers continue to be used in tritium handling systems. In tritium handling systems, polymers are employed mainly in joining applications such as valve sealing surfaces (eg. Stem tips, valve packing, and O-rings). Because of the continued need to employ polymers in tritium systems, over the past several years, programs at the Savannah River National Laboratory have been studying the effect of tritium on various polymers of interest. In these studies, samples of materials of interest to the SRS Tritium Facilities (ultra-high molecular weight polyethylene (UHMW-PE), polytetrafluoroethylene (PTFE, Teflon{reg_sign}), Vespel{reg_sign} polyimide, and the elastomer

  6. The spectral irradiance traceability chain at PTB

    NASA Astrophysics Data System (ADS)

    Sperfeld, P.; Pape, S.; Nevas, S.

    2013-05-01

    Spectral irradiance is a fundamental radiometric unit. Its application to measurement results requires qualified traceability to basic units of the international system of units (Système international d'unités, SI). The Physikalisch-Technische Bundesanstalt (PTB) is amongst other national metrological institutes (NMIs) responsible for the realization, maintenance and dissemination of various radiometric and photometric units based on and traceable to national standards. The unit of spectral irradiance is realized and represented by a blackbody-radiator as the national primary standard of the PTB. Based on Planck's radiation law, the irradiance is calculated and realized for any wavelength taking into account the exact knowledge of the radiation temperature and the geometrical parameters. Using a double-monochromator-based spectroradiometer system, secondary standard lamps can be calibrated by direct comparison to the blackbody-radiator (substitution method). These secondary standard lamps are then used at the PTB to calibrate standard lamps of customers. The customers themselves use these so-called transfer standards to calibrate their working standard lamps. These working standards are then used to calibrate own spectroradiometers or sources. This rather complex calibration chain is a common procedural method that for the customers generally leads to satisfying measurement results on site. Nevertheless, the standard lamps in use have to fulfill highest requirements concerning stability and reproducibility. Only this allows achieving comparably low transfer measurement uncertainties, which occur at each calibration step. Thus, the PTB is constantly investigating the improvement and further development of transfer standards and measurement methods for various spectral regions. The realization and dissemination of the spectral irradiance using the blackbody-radiator at the PTB is accomplished with worldwide approved minimized measurement uncertainties confirmed by

  7. Evaluation of various procedures transposing global tilted irradiance to horizontal surface irradiance

    NASA Astrophysics Data System (ADS)

    Housmans, Caroline; Bertrand, Cédric

    2017-02-01

    Many transposition models have been proposed in the literature to convert solar irradiance on the horizontal plane to that on a tilted plane. The inverse process, i.e. the conversion from tilted to horizontal is investigated here based upon seven months of in-plane global solar irradiance measurements recorded on the roof of the Royal Meteorological Institute of Belgium's radiation tower in Uccle (Longitude 4.35° E, Latitude 50.79° N). Up to three pyranometers mounted on inclined planes of different tilts and orientations were involved in the inverse transposition process. Our results indicate that (1) the tilt to horizontal irradiance conversion is improved when measurements from more than one tilted pyranometer are considered (i.e. by using a multi-pyranometer approach) and (2) the improvement from using an isotropic model to anisotropic models in the inverse transposition problem is not significant.

  8. Preliminary analysis of irradiation effects on CLAM after low dose neutron irradiation

    NASA Astrophysics Data System (ADS)

    Peng, Lei; Huang, Qunying; Li, Chunjing; Liu, Shaojun

    2009-04-01

    To investigate the irradiation effects on a new version of reduced activation ferritic/martensitic steels (RAFMs) i.e. China Low Activation Martensitic steel (CLAM), neutron irradiation experiments has been being carried out under wide collaboration in China and overseas. In this paper, the mechanical properties of CLAM heats 0603A, 0408B, and 0408D were investigated before and after neutron irradiation to ˜0.02 dpa at 250 °C. The test results showed that ultimate strength and yield stress of CLAM HEAT 0603A increased about 10-30 MPa and ductile to brittle transition temperature (DBTT) shift was about 5 °C. For CLAM heats 0408B and 0408D, ultimate strength and yield stress increased about 80-150 MPa.

  9. Gamma irradiation treatment of cereal grains for chick diets

    SciTech Connect

    Campbell, G.L.; Classen, H.L.; Ballance, G.M.

    1986-04-01

    Wheat (W), triticale (T), hulled barley (HB), hull-less barley (HLB), hulled oats (HO), and hull-less oats (HLO) were gamma irradiated (/sup 60/Co) at 0, 3, 6 and 9 Mrad to study the effect of irradiation on the nutritional value of cereal grains for chicks. A significant curvilinear relationship between radiation dose and 3-wk body weight of chicks fed irradiated cereals was noted for T, HB, HLB, HO and HLO. Chicks fed W or T showed no effect or lower body weight, respectively, while body weights of chicks fed barley or oat samples were higher with irradiation. The improvement tended to be maximal at the 6 Mrad level. Irradiation significantly improved the gain-to-feed ratio for chicks fed either HO or HLO. Apparent fat retention and tibia ash were higher in chicks fed irradiated HLO than in those fed untreated HLO. In a second experiment chick body weight, apparent amino acid and fat retention, tibia ash, and gain-to-feed ratios were lower in chicks fed autoclaved (121 degrees C for 20 min) barley than in those fed untreated barley. Irradiation (6 Mrad) subsequent to autoclaving barley samples eliminated these effects. Irradiation appears to benefit cereals containing soluble or mucilagenous fiber types as typified by beta-glucan of barley and oats. These fibers appear prone to irradiation-induced depolymerization, as suggested by increased beta-glucan solubility and reduced extract viscosity for irradiated barley and oat samples.

  10. Physicochemical and sensory properties of irradiated dry-cured ham

    NASA Astrophysics Data System (ADS)

    Jin, Sang-Keun; Kim, Chul-Wook; Chung, Ki-Hwa; Jo, Kwang-Keun; Jeong, Jin-Yeon; Hur, In-Chul; Jung, Eun-Young; Joo, Seon-Tea; Yang, Han-Sul

    2012-02-01

    To determine the effect of different irradiation doses on ready-to-eat (RTE) dry-cured shoulder hams, physicochemical and sensory attributes were analyzed during 8 weeks of refrigerated storage. The results show that irradiation reduced the redness value and increased the 2-thiobarbituric acid-reactive substance (TBARS) value as well as the irradiation aroma during storage. However, ham samples irradiated with 2.5 and 5.0 kGy did not show significant changes in lightness values compared to the control sample during 8 weeks of storage. TBARS values were lower in the sample irradiated with 2.5 kGy than in the other irradiated samples. The total plate counts of the 5.0 kGy-irradiated samples were not measured after 0 weeks. Sensory panels found that the 2.5- and 5.0 kGy-irradiated samples had better overall acceptability scores than the other irradiated samples. It was concluded that treatments with lower levels of irradiation (≤5.0 kGy) can enhance the microbial safety and sensory acceptance of dry-cured shoulder hams.

  11. Evaluation of Neutron Irradiated Silicon Carbide and Silicon Carbide Composites

    SciTech Connect

    Newsome G, Snead L, Hinoki T, Katoh Y, Peters D

    2007-03-26

    The effects of fast neutron irradiation on SiC and SiC composites have been studied. The materials used were chemical vapor deposition (CVD) SiC and SiC/SiC composites reinforced with either Hi-Nicalon{trademark} Type-S, Hi-Nicalon{trademark} or Sylramic{trademark} fibers fabricated by chemical vapor infiltration. Statistically significant numbers of flexural samples were irradiated up to 4.6 x 10{sup 25} n/m{sup 2} (E>0.1 MeV) at 300, 500 and 800 C in the High Flux Isotope Reactor at Oak Ridge National Laboratory. Dimensions and weights of the flexural bars were measured before and after the neutron irradiation. Mechanical properties were evaluated by four point flexural testing. Volume increase was seen for all bend bars following neutron irradiation. Magnitude of swelling depended on irradiation temperature and material, while it was nearly independent of irradiation fluence over the fluence range studied. Flexural strength of CVD SiC increased following irradiation depending on irradiation temperature. Over the temperature range studied, no significant degradation in mechanical properties was seen for composites fabricated with Hi-Nicalon{trademark} Type-S, while composites reinforced with Hi-Nicalon{trademark} or Sylramic fibers showed significant degradation. The effects of irradiation on the Weibull failure statistics are also presented suggesting a reduction in the Weibull modulus upon irradiation. The cause of this potential reduction is not known.

  12. Effect of Electron Beam Irradiation on Tensile Strength of Polypropylene

    NASA Astrophysics Data System (ADS)

    Yamada, Hiroshi; Ikeda, Masayuki; Shimbo, Minoru; Miyano, Yasushi

    In this paper, the effects of the intensity of electron beam and the variation with time after irradiation of electron beam on the tensile strength of the polypropylene (PP), which is widely used as medicine containers, were investigated. PP with and without colorants were used first and samples irradiated under various intensity of EB. A tensile test on the irradiated samples with elapsed time after the irradiation of the electron beam was carried out. The effects of those factors on the tensile strength were discussed. The following results were obtained (1) The tensile strength of PP decreased due to the influence of the electron beam irradiation, however the rate of the decrease in strength was small compared with the original one. Furthermore, the rate of the decrease in strength was very small owing to the variation with time after the EB irradiation. (2) The tensile rupture strength of PP increased and the rupture strain owing to the influence of the electron beam irradiation compared with the original one. In addition, these rupture strength increased and the rupture strain decreased along with time after the irradiation of the electron beam. (3) The tensile rupture strain energy of PP decreased owing to the influence of the electron beam irradiation compared with the original one. In addition, the strain energy decreases with time after the irradiation of the electron beam. Moreover, the strength characteristics of PP with colorants received greater influence of electron beam compared with the one without colorants.

  13. Bystander responses in low dose irradiated cells treated with plasma from gamma irradiated blood

    NASA Astrophysics Data System (ADS)

    Acheva, A.; Georgieva, R.; Rupova, I.; Boteva, R.; Lyng, F.

    2008-02-01

    There are two specific low-dose radiation-induced responses that have been the focus of radiobiologists' interest in recent years. These are the bystander effect in non-irradiated cells and the adaptive response to a challenge dose after prior low dose irradiation. In the present study we have investigated if plasma from irradiated blood can act as a 'challenge dose' on low dose irradiated reporter epithelial cells (HaCaT cell line). The main aim was to evaluate the overall effect of low dose irradiation (0.05 Gy) of reporter cells and the influence of bystander factors in plasma from 0.5 Gy gamma irradiated blood on these cells. The effects were estimated by clonogenic survival of the reporter cells. We also investigated the involvement of reactive oxygen species (ROS) as potential factors involved in the bystander signaling. Calcium fluxes and mitochondrial membrane potential (MMP) depolarization were also examined as a marker for initiation of apoptosis in the reporter cells. The results show that there are large individual differences in the production of bystander effects and adaptive responses between different donors. These may be due to the specific composition of the donor plasma. The observed effects generally could be divided into two groups: adaptive responses and additive effects. ROS appeared to be involved in the responses of the low dose pretreated reporter cells. In all cases there was a significant decrease in MMP which may be an early event in the apoptotic process. Calcium signaling also appeared to be involved in triggering apoptosis in the low dose pretreated reporter cells. The heterogeneity of the bystander responses makes them difficult to be modulated for medical uses. Specific plasma characteristics that cause these large differences in the responses would need to be identified to make them useful for radiotherapy.

  14. Effect of gamma irradiation on Korean traditional multicolored paintwork

    NASA Astrophysics Data System (ADS)

    Yoon, Minchul; Kim, Dae-Woon; Choi, Jong-il; Chung, Yong-Jae; Kang, Dai-Ill; Hoon Kim, Gwang; Son, Kwang-Tae; Park, Hae-Jun; Lee, Ju-Woon

    2015-10-01

    Gamma irradiation can destroy fungi and insects involved in the bio-deterioration of organic cultural heritages. However, this irradiation procedure can alter optical and structural properties of historical pigments used in wooden cultural heritage paintings. The crystal structure and color centers of these paintings must be maintained after application of the irradiation procedure. In this study, we investigated the effects of gamma irradiation on Korean traditional multicolored paintwork (Dancheong) for the preservation of wooden cultural heritages. The main pigments in Korean traditional wooden cultural heritages, Sukganju (Hematite; Fe2O3), Jangdan (Minium; Pb3O4), Whangyun (Crocoite; PbCrO4), and Jidang (Rutile; TiO2), were irradiated by gamma radiation at doses of 1, 5, and 20 kGy. After irradiation, changes in Commision Internationale d'Eclairage (CIE) color values (L*, a*, b*) were measured using the color difference meter, and their structural changes were analyzed using X-ray diffraction (XRD) analysis. The slightly change in less than 1 dE* unit by gamma irradiation was observed, and structural changes in the Dancheong were stable after exposure to 20 kGy gamma irradiation. In addition, gamma irradiation could be applied to painted wooden cultural properties from the Korean Temple. Based on the color values, gamma irradiation of 20 kGy did not affect the Dancheong and stability was maintained for five months. In addition, the fungicidal and insecticidal effect by less than 5 kGy gamma irradiation was conformed. Therefore, the optical and structural properties of Dancheong were maintained after gamma irradiation, which suggested that gamma irradiation can be used for the preservation of wooden cultural heritages painted with Dancheong.

  15. Post-irradiation-examination of irradiated fuel outside the hot cell

    SciTech Connect

    Dawn E. Janney; Adam B. Robinson; Thomas P. O'Holleran; R. Paul Lind; Marc Babcock; Laurence C. Brower; Julie Jacobs; Pamela K. Hoggan

    2007-09-01

    Because of their high radioactivity, irradiated fuels are commonly examined in a hot cell. However, the Idaho National Laboratory (INL) has recently investigated irradiated U-Mo-Al metallic fuel from the Reduced Enrichment for Research and Test Reactors (RERTR) project using a conventional unshielded scanning electron microscope outside a hot cell. This examination was possible because of a two-step sample-preparation approach in which a small volume of fuel was isolated in a hot cell and shielding was introduced during later stages of sample preparation. The resulting sample contained numerous sample-preparation artifacts but allowed analysis of microstructures from selected areas.

  16. Qualité de vie et vécu de la maladie, avant et après hystérectomie vaginale, chez les femmes admises au Centre Hospitalier Universitaire de Brazzaville

    PubMed Central

    Mbongo, Jean Alfred; Mouanga, Alain; Miabaou, Didace Massamba; Nzelie, Aya; Iloki, Léon Hervé

    2016-01-01

    Toute maladie est un mal en soi qu’il faut éradiquer car elle altère souvent de façon significative la qualité de la vie. L’hystérectomie vaginale est indiquée pour les patientes qui présentent certaines affections gynécologiques graves, elle est donc bénéfique mais, peut également avoir une répercussion néfaste sur la qualité de vie de la femme. Ainsi nous avons voulu explorer le vécu de la maladie et de l’hystérectomie vaginale (HV) des femmes avant et après l’intervention chirurgicale. Nous avons effectué une étude prospective qualitative, à recueil clinique sur une période de 12 mois; qui a concerné les femmes, ayant subi une hystérectomie vaginale. Celles n’ayant pas accepté de participer à l’étude, ou n’ayant pas de contact téléphonique n’ont pas été incluses. Pendant la maladie, le vécu des femmes a été: l’inconfort sexuel 26/40 (65%); les saignements génitaux 12/40 (30%); les douleurs pelviennes 13/40 (32,5%). En Post-opératoire, ont été noté les dyspareunies transitoires30/40 (75%) ; les céphalées secondaires à l’anesthésie 4/40 (10%). Le vécu psychologique a été dominé avant l’HV par la peur de la chirurgie chez toutes les patientes, les troubles du sommeil 38/40 (95%), l’angoisse 30 /40(75%), un sentiment de honte lié aux difficultés à accomplir l’acte sexuel en raison du prolapsus 26/40(65%) et/ ou en raison des saignements génitaux, dus au fibrome utérin 14/40(35%). Le sentiment de la perte de féminité était déclaré par 26/40 femmes porteuses de prolapsus utérin (65%), la modification de l’estime de soi 26/40 (65%). Ces appréciations subjectives ont été améliorées avec l’HV, contre balançant la perte de leur organe de reproduction. Aucune information n’a été donnée par les femmes à leurs proches et aux membres de la famille avant la chirurgie, traduisant ainsi leur sentiment de gène ou de honte. L’arrêt des symptômes a été observé dans tous les

  17. Development of microstructure and irradiation hardening of Zircaloy during low dose neutron irradiation at nominally 358 C

    SciTech Connect

    Cockeram, Brian V; Smith, Richard W; Leonard, Keith J; Byun, Thak Sang; Snead, Lance Lewis

    2011-01-01

    Wrought Zircaloy-2 and Zircaloy-4 were neutron irradiated at nominally 358 C in the high flux isotope reactor (HFIR) at relatively low neutron fluences between 5.8 1022 and 2.9 1025 n/m2 (E > 1 MeV). The irradiation hardening and change in microstructure were characterized following irradiation using tensile testing and examinations of microstructure using Analytical Electron Microscopy (AEM). Small increments of dose (0.0058, 0.11, 0.55, 1.08, and 2.93 1025 n/m2) were used in the range where the saturation of irradiation hardening is typically observed so that the role of microstructure evolution and hai loop formation on irradiation hardening could be correlated. An incubation dose between 5.8 1023 and 1.1 1024 n/m2 was needed for loop nucleation to occur that resulted in irradiation hardening. Increases in yield strength were consistent with previous results in this temperature regime, and as expected less irradiation hardening and lower hai loop number density values than those generally reported in literature for irradiations at 260 326 C were observed. Unlike previous lower temperature data, there is evidence in this study that the irradiation hardening can decrease with dose over certain ranges of fluence. Irradiation induced voids were observed in very low numbers in the Zircaloy-2 materials at the highest fluence.

  18. Formation of hazardous by-products resulting from the irradiation of natural organic matter: comparison between UV and VUV irradiation.

    PubMed

    Buchanan, W; Roddick, F; Porter, N

    2006-05-01

    The use of ultraviolet (UV) or vacuum ultraviolet (VUV) photo-oxidation followed by biological treatment for the removal of natural organic matter (NOM) in drinking water is a potential water treatment technique under investigation. This paper reports on the trihalomethane formation potential (THMFP), the haloacetic acid formation potential (HAAFP), and formation of nitrite and peroxide following both UV and VUV irradiation of NOM prior to biological treatment. The total THMFP was found to decrease with increasing UV and VUV irradiation dose, although there was a linear increase in bromoform formation. Determination of the THMFP of NOM fractions obtained after irradiation, showed that the hydrophobic fraction was dominated by chlorinated species which accounted for the majority of the total THMFP, while bromoform was observed only in the hydrophilic fraction of NOM. VUV irradiation reduced the HAAFP with increasing dose, in contrast, UV irradiation had a limited effect on the overall HAAFP. Following UV or VUV irradiation, the chlorinated species accounted for the majority of HAAFP; however, significant formation of brominated haloacetic acid (HAA) was observed. The nitrate concentration of the untreated water directly influenced the concentration of nitrite produced as a consequence of UV and VUV irradiation. Hydrogen peroxide formation was greater during VUV irradiation than during UV irradiation. Samples exposed to various doses of UV or VUV irradiation (up to 138 J cm(-2)) were deemed non-cytotoxic (African green monkey kidney cells) and non-mutagenic (Ames test).

  19. NANOSTRUCTURE PATTERNING UNDER ENERGETIC PARTICLE BEAM IRRADIATION

    SciTech Connect

    Wang, Lumin; Lu, Wei

    2013-01-31

    Energetic ion bombardment can lead to the development of complex and diverse nanostructures on or beneath the material surface through induced self-organization processes. These self-organized structures have received particular interest recently as promising candidates as simple, inexpensive, and large area patterns, whose optical, electronic and magnetic properties are different from those in the bulk materials [1-5]. Compared to the low mass efficiency production rate of lithographic methods, these self-organized approaches display new routes for the fabrication of nanostructures over large areas in a short processing time at the nanoscale, beyond the limits of lithography [1,4]. Although it is believed that surface nanostructure formation is based on the morphological instability of the sputtered surface, driven by a kinetic balance between roughening and smoothing actions [6,7], the fundamental mechanisms and experimental conditions for the formation of these nanostructures has still not been well established, the formation of the 3-D naopatterns beneath the irradiated surface especially needs more exploration. During the last funding period, we have focused our efforts on irradiation-induced nanostructures in a broad range of materials. These structures have been studied primarily through in situ electron microscopy during electron or ion irradiation. In particular, we have performed studies on 3-D void/bubble lattices (in metals and CaF2), embedded sponge-like porous structure with uniform nanofibers in irradiated semiconductors (Ge, GaSb, and InSb), 2-D highly ordered pattern of nanodroplets (on the surface of GaAs), hexagonally ordered nanoholes (on the surface of Ge), and 1-D highly ordered ripple and periodic arrays (of Cu nanoparticles) [3,8-11]. The amazing common feature in those nanopatterns is the uniformity of the size of nanoelements (nanoripples, nanodots, nanovoids or nanofibers) and the distance separating them. Our research focuses on the

  20. Physicochemical and structural characteristics of rice starch modified by irradiation.

    PubMed

    Polesi, Luís Fernando; Sarmento, Silene Bruder Silveira; Moraes, Jaqueline de; Franco, Célia Maria Landi; Canniatti-Brazaca, Solange Guidolin

    2016-01-15

    This work evaluated the physicochemical and structural properties of rice starch of the cultivars IAC 202 and IRGA 417 modified by irradiation. Starch samples were irradiated by (60)Co in doses 1, 2 and 5kGy, on a rate of 0.4kGy/h. A control not irradiated was used for comparison. The granule morphology and A-type X-ray diffraction pattern were not altered by irradiation. There was an increase in amylose content, carboxyl content and acidity with irradiation. Gamma radiation did not affect the thermal properties of IAC202, but increased gelatinization temperature of IRGA417, in the higher dose (5kGy). The number of long chains of amylopectin was reduced and short chains were increased for IAC202, whereas for IRGA 417, the opposite was observed, probably due to cross-linking of starch chains. Starches had their physicochemical and structural properties modified by irradiation differently.

  1. Safety evaluation of irradiated foods in China: A condensed report

    SciTech Connect

    Yin, D. )

    1989-03-01

    Eight trials, with 439 human volunteers who consumed irradiated foods including rice, potatoes, mushrooms, peanuts, and Chinese sausages, as well as diets composed of multiple irradiated foods (irradiated at dosages of 0.2 to 8 kGy) that accounted for 60-66% of the entire diet, were carried out for 2-3 months according to a unified protocol. No adverse effects on body weight, blood pressure, ECG, hematology, blood enzyme activities, serum lipids or blood or urine 17-hydroxycortisol contents and no chromosomal aberration of peripheral blood lymphocytes were found. It is especially worthwhile to note that there was no change in the polyploidy after consumption of irradiated diets. On the basis of these results and a comprehensive analysis of the physical and chemical characteristics of irradiated foods, temporary hygienic standards for irradiated rice, potatoes, onions, garlic, Chinese sausages, peanuts, and mushrooms were promulgated by the Chinese Ministry of Public Health.

  2. Spectral properties of ion irradiated carbon rich solids

    NASA Astrophysics Data System (ADS)

    Strazzulla, G.; Baratta, G.; Brunetto, R.; Garozzo, M.; Kanuchova, Z.

    2009-04-01

    Carbon rich solid materials have been studied before, during, and after ion irradiation (3-400 keV ions) by in situ reflectance spectroscopy (from UV to IR). Frozen hydrocarbons (benzene, methane, butane, acetylene, etc., also mixed with water ice) have been irradiated at low temperature with fast ions. Irradiation causes the formation of many molecular species and of a long chain polymer like material (organic refractory residue). The process mimics what occurs in space because of cosmic ion irradiation of the icy surfaces of some objects in the Solar System. Other irradiated materials include natural bitumens (Asphaltite, kerite) and polymers (i.e. polystyrene). Upon irradiation the originally transparent polymer samples are converted in a material that, already at low doses, strongly absorbs in the UV. Such materials could mimic a kind of organic material (i.e. a spectrally neutral one) freshly exposed at the surface of minor objects in the Solar System because of meteoritic impact.

  3. Solar irradiance measurements - Minimum through maximum solar activity

    NASA Technical Reports Server (NTRS)

    Lee, R. B., III; Gibson, M. A.; Shivakumar, N.; Wilson, R.; Kyle, H. L.; Mecherikunnel, A. T.

    1991-01-01

    The Earth Radiation Budget Satellite (ERBS) and the NOAA-9 spacecraft solar monitors were used to measure the total solar irradiance during the period October 1984 to December 1989. Decreasing trends in the irradiance measurements were observed as sunspot activity decreased to minimum levels in 1986; after 1986, increasing trends were observed as sunspot activity increased. The magnitude of the irradiance variability was found to be approximately 0.1 percent between sunspot minimum and maximum (late 1989). When compared with the 1984 to 1989 indices of solar magnetic activity, the irradiance trends appear to be in phase with the 11-year sunspot cycle. Both irradiance series yielded 1,365/sq Wm as the mean value of the solar irradiance, normalized to the mean earth/sun distance. The monitors are electrical substitution, active-cavity radiometers with estimated measurement precisions and accuracies of less than 0.02 and 0.2 percent, respectively.

  4. Performance of single crystalline silicon solar cell with irradiance

    NASA Astrophysics Data System (ADS)

    Chander, Subhash; Purohit, A.; Nehra, Anshu; Nehra, S. P.; Dhaka, M. S.

    2015-06-01

    In this paper, the effect of irradiance on the performance parameters of single crystalline silicon solar cell is undertaken. The experiment was carried out employing solar cell simulator with varying irradiance in the range 115-550W/m2 at constant cell temperature 25°C. The results show that the short circuit current is found to be increased linearly with irradiance and the open circuit voltage is increased slightly. The fill factor, maximum power and cell efficiency are also found to be increased with irradiance. The efficiency is increased linearly at lower irradiance while slightly increased at higher. The results revealed that the irradiance has a dominant effect on the performance parameters. The results are in good agreement with the available literature.

  5. Commercialization of food irradiation in the U.S.A.

    NASA Astrophysics Data System (ADS)

    Cottee, Jim; Kunstadt, Peter; Fraser, Frank

    1995-02-01

    Commercializing food irradiation in the United States has been a major marketing and business challenge. This paper begins by examining the situation before America's first food irradiator was established, in 1992. With the Vindicator irradiator in place, beneficial changes and market offerings took place, amidst perceived activist threats and disinterest from the food industry. Initial efforts to market irradiated foods were made by independents in the food business, as part of their attempts to differentiate themselves from large food companies and grocery chains. Special tactics were needed to launch products into sensitive and fearful market-places. The brisk sales of irradiated foods in small, initial markets, has been an unexpected success. This paper discusses the methods used to promote positive awareness of irradiated foods nationally, building on small local successes.

  6. Up-to-date status of food irradiation

    NASA Astrophysics Data System (ADS)

    Ahmed, Mainuddin

    1993-07-01

    The last decade has witnessed significant advancement of the acceptance of food irradiation processing. At present 37 countries have approved one or more food items for human consumption and 25 countries have commercialized this process. More developing countries are showing keen interest to introduce irradiation processing in order to reduce post-harvest food losses, to increase export potentials and to ensure safety of food to their people. Although progress towards acceptance of food irradiation by the industry is slow, actual market trials have shown that once consumers have understood this technology, they are willing to buy irradiated foods. This paper deals with the latest developments in the field of food irradiation with particular reference to legislation, consumer acceptance, commercialization and potential application in developing countries. This paper also deals with the role played by the International Organizations, aimed at facilitating the acceptance of food irradiation.

  7. Antioxidant Approaches to Management of Ionizing Irradiation Injury

    PubMed Central

    Greenberger, Joel; Kagan, Valerian; Bayir, Hulya; Wipf, Peter; Epperly, Michael

    2015-01-01

    Ionizing irradiation induces acute and chronic injury to tissues and organs. Applications of antioxidant therapies for the management of ionizing irradiation injury fall into three categories: (1) radiation counter measures against total or partial body irradiation; (2) normal tissue protection against acute organ specific ionizing irradiation injury; and (3) prevention of chronic/late radiation tissue and organ injury. The development of antioxidant therapies to ameliorate ionizing irradiation injury began with initial studies on gene therapy using Manganese Superoxide Dismutase (MnSOD) transgene approaches and evolved into applications of small molecule radiation protectors and mitigators. The understanding of the multiple steps in ionizing radiation-induced cellular, tissue, and organ injury, as well as total body effects is required to optimize the use of antioxidant therapies, and to sequence such approaches with targeted therapies for the multiple steps in the irradiation damage response. PMID:26785339

  8. Modeling and prediction of irradiation assisted stress corrosion cracking

    SciTech Connect

    Andresen, P.L.; Ford, F.P.

    1995-12-31

    Following an introduction to the phenomenology and consequences of irradiation assisted stress corrosion cracking (IASCC), the many common aspects of SCC response in unirradiated and irradiated environments is reviewed. From a secure basis of understanding and predictive modeling under unirradiated conditions, the effects of individual irradiation phenomena are identified and modeled. The individual effects of radiation on segregation, creep/stress relaxation, hardening, and radiolytic water chemistry are modeled based on the best available data, some from proprietary sources. Critical issues are addressed, such as the possibility that radiation produces very high corrosion potentials in crevices/cracks under irradiated conditions. A wide variety of irradiated laboratory data and field observations provides a basis for comparison with prediction and an optimism that, despite an imperfect understanding of irradiation phenomena, it is possible to develop predictive algorithms that characterize IASCC with reasonable accuracy and, from that, to develop an effective approach for life prediction.

  9. Thermal analysis of the FSP-1RR irradiation test

    SciTech Connect

    Webb, R.H.; Lyon, W.F. III

    1992-10-14

    The thermal analysis of four unirradiated fuel pins to be tested in the FSP-1RR fuels irradiation experiment was completed. This test is a follow-on experiment in the series of fuel pin irradiation tests conducted by the SP-100 Program in the Fast Flux Test Facility. One of the pins contains several meltwire temperature monitors within the fuel and the Li annulus. A post-irradiation examination will verify the accuracy of the pre-irradiation thermal analysis. The purpose of the pre-irradiation analysis was to determine the appropriate insulating gap gas compositions required to provide the design goal cladding operating temperatures and to ensure that the meltwire temperature ranges in the temperature monitored pin bracket peak irradiation temperatures. This paper discusses the methodology and summarizes the results of the analysis.

  10. Thermal analysis of the FSP-1RR irradiation test

    SciTech Connect

    Webb, R.H.; Lyon, W.F. III )

    1993-01-10

    The thermal analysis of four unirradiated fuel pins to be tested in the FSP-1RR fuels irradiation experiment was completed. This test is a follow-on experiment in the series of fuel pin irradiation tests conducted by the SP-100 Program in the Fast Flux Test Facility. One of the pins contains several meltwire temperature monitors within the fuel and the Li annulus. A post-irradiation examination will verify the accuracy of the pre-irradiation thermal analysis. The purpose of the pre-irradiation analysis was to determine the appropriate insulating gap gas compositions required to provide the design goal cladding operating temperatures and to ensure that the meltwire temperature ranges in the temperature monitored pin bracket peak irradiation temperatures. This paper discusses the methodology and summarizes the results of the analysis.

  11. Hydrodynamic Simulations of Unevenly Irradiated Jovian Planets

    NASA Astrophysics Data System (ADS)

    Langton, Jonathan; Laughlin, Gregory

    2008-02-01

    We employ a two-dimensional, grid-based hydrodynamic model to simulate upper atmospheric dynamics on extrasolar giant planets. The hydrodynamic equations of motion are integrated on a rotating, irradiated sphere using a pseudospectral algorithm. We use a two-frequency, two-stream approximation of radiative transfer to model the temperature forcing. This model is well suited to simulate the dynamics of the atmospheres of planets with high orbital eccentricity, which are subject to widely varying irradiation conditions. We identify six such planets, with eccentricities between e = 0.28 and e = 0.93 and semimajor axes from a = 0.0508 AU to a = 0.432 AU, as particularly interesting. For each, we determine the temperature profile and resulting infrared light curves in the 8 μm Spitzer band. Especially notable are the results for HD 80606b, which has the largest eccentricity (e = 0.9321) of any known planet, and HAT-P-2b, which transits its parent star, so that its physical properties are well constrained. Despite the varied orbital parameters, the atmospheric dynamics of these planets display a number of interesting common properties. In all cases, the atmospheric response is primarily driven by the intense irradiation at periastron. The resulting expansion of heated air produces high-velocity turbulent flow, including long-lived circumpolar vortices. In addition, a superrotating acoustic front develops on some planets; the strength of this disturbance depends on both the eccentricity and the temperature gradient from uneven heating. The specifics of the resulting infrared light curves depend strongly on the orbital geometry. We show, however, that the variations on HD 80606b and HAT-P-2b should be readily detectable at 4.5 and 8 μm using Spitzer. These two objects present the most attractive observational targets of all known high-e exoplanets.

  12. Protostellar chemistry dominated by external irradiation

    NASA Astrophysics Data System (ADS)

    Lindberg, Johan E.; Charnley, Steven B.; Jørgensen, Jes K.; Watanabe, Yoshimasa; Bisschop, Suzanne E.; Sakai, Nami; Yamamoto, Satoshi

    2015-08-01

    In their youngest stages, protostars are deeply enshrouded in envelopes of gas and dust, material that later accretes onto the central object and the protoplanetary disc. The chemical composition and excitation properties measured towards these envelopes provide valuable information about the current and previous irradiation environment of the forming protostar.We demonstrate the strengths of unbiased single-dish line surveys, which we use to study the chemical and physical properties of protostellar envelopes. We have performed line surveys of more than 50 sources in the nearby Corona Australis and Ophiuchus star-forming regions using the APEX telescope. Many of the Corona Australis sources are located near the intermediate-mass Herbig Be star R CrA, and we find that despite its moderate luminosity, the irradiation from this star enhances the H2CO temperatures of the nearby protostellar envelopes from 10 K to at least 30-40 K. This drastically elevated temperature should be of crucial importance to the chemistry of these envelopes, due to thermal evaporation of many key species from the dust grain surfaces.Towards R CrA-IRS7B, the most thoroughly investigated object in our study, we find that the chemistry differs greatly from other thoroughly investigated deeply embedded protostars (hot corinos and warm carbon-chain chemistry sources, WCCC). We find low abundances of complex organic molecules such as CH3OCH3 and CH3CN, but instead elevated abundances of CN and some carbon-chain species like HC3N and C2H, although not to the same level as towards typical WCCC sources. We interpret the observed chemical properties as a result of thermal evaporation of CO from the grain mantles and photo-dissociation reactions in the IRS7B envelope, both initiated by the irradiation from R CrA.

  13. A Simplified Shuttle Irradiation Facility for ATR

    SciTech Connect

    Palmer, Alma Joseph; Laflin, S. T.

    1999-09-01

    During the past fifteen years there has been a steady increase in the demand for radioisotopes in nuclear medicine and a corresponding decline in the number of reactors within the U.S. capable of producing them. The Advanced Test Reactor (ATR) is the largest operating test reactor in the U.S., but its isotope production capabilities have been limited by the lack of an installed isotope shuttle irradiation system. A concept for a simple “low cost” shuttle irradiation facility for ATR has been developed. Costs were reduced (in comparison to previous ATR designs) by using a shielded trough of water installed in an occupiable cubicle as a shielding and contamination control barrier for the send and receive station. This shielding concept also allows all control valves to be operated by hand and thus the need for an automatic control system was eliminated. It was determined that 4 – 5 ft of water would be adequate to shield the isotopes of interest while shuttles are transferred to a small carrier. An additional feature of the current design is a non-isolatable by-pass line, which provides a minimum coolant flow to the test region regardless of which control valves are opened or closed. This by-pass line allows the shuttle facility to be operated without bringing reactor coolant water into the cubicle except for send and receive operations. The irradiation position selected for this concept is a 1.5 inch “B” hole (B-11). This position provides neutron fluxes of approximately: 1.6 x 1014 (<0.5 eV) and 4.0 x 1013 (>0.8 MeV) n/cm2*sec.

  14. Early and Late Responses to Ion Irradiation

    NASA Astrophysics Data System (ADS)

    Schulte, Reinhard; Ling, Ted

    Early and late responses to ion beam therapy (IBT) are the result of complex interactions between host, dose volume, and radiobiological factors. Our understanding of these early and late tissue responses has improved greatly with the accumulation of laboratory and clinical experience with proton and heavy ion irradiation. With photon therapy becoming increasingly conformal, many concepts developed for 3D conformal radiotherapy and intensity modulated radiation therapy with photons are also applicable to IBT. This chapter reviews basic concepts and experimental data of early and late tissue responses to protons and ions.

  15. Nasopharyngeal radium irradiation: The lessons of history.

    PubMed

    Graamans, Kees

    2017-02-01

    In the Netherlands, nasopharyngeal radium irradiation was started in 1945. The indications included refractory symptoms of otitis media with effusion and other adenoid-related disorders after adenoidectomy. It was considered a safe and effective therapy. Its use decreased sharply in 1958, following a worldwide media avalanche around the dramatic events in the treatment of a 5-year-old child in Utrecht, enhancing the widespread fear of radioactivity. This case history illustrates the powerful role of the media in medical decision-making.

  16. DECONTAMINATION OF NEUTRON-IRRADIATED REACTOR FUEL

    DOEpatents

    Buyers, A.G.; Rosen, F.D.; Motta, E.E.

    1959-12-22

    A pyrometallurgical method of decontaminating neutronirradiated reactor fuel is presented. In accordance with the invention, neutron-irradiated reactor fuel may be decontaminated by countercurrently contacting the fuel with a bed of alkali and alkaine fluorides under an inert gas atmosphere and inductively melting the fuel and tracking the resulting descending molten fuel with induction heating as it passes through the bed. By this method, a large, continually fresh surface of salt is exposed to the descending molten fuel which enhances the efficiency of the scrubbing operation.

  17. Microstructural examination of irradiated vanadium alloys

    SciTech Connect

    Gelles, D.S.; Chung, H.M.

    1997-04-01

    Microstructural examination results are reported for a V-5Cr-5Ti unirradiated control specimens of heat BL-63 following annealing at 1050{degrees}C, and V-4Cr-4Ti heat BL-47 irradiated in three conditions from the DHCE experiment: at 425{degrees}C to 31 dpa and 0.39 appm He/dpa, at 600{degrees}C to 18 dpa and 0.54 appm He/dpa and at 600{degrees}C to 18 dpa and 4.17 appm He/dpa.

  18. Preoperative irradiation and cystectomy for bladder cancer.

    PubMed

    Smith, J A; Batata, M; Grabstald, H; Sogani, P C; Herr, H; Whitmore, W F

    1982-03-01

    Between 1971 and 1974, 101 patients at Memorial Sloan-Kettering Cancer Center underwent planned integrated treatment for bladder cancer with 2000 rads by megavoltage delivered to the whole pelvis over five consecutive days followed by radical cystectomy within a week. The overall five-year survival rate was 39%; the hospital mortality rate was 2%. In the pelvis alone tumor recurred in 9% of the patients. These results support other studies demonstrating the efficacy of this and other regimens of preoperative irradiation and cystectomy.

  19. Medical waste irradiation study. Final report

    SciTech Connect

    Adler, R.J.; Stein, J.; Nygard, J.

    1998-07-25

    The North Star Research Corporation Medical Waste project is described in this report, with details of design, construction, operation, and results to date. The project began with preliminary design of the accelerator. The initial design was for a single accelerator chamber with a vacuum tube cavity driver built into the chamber itself, rather than using a commercial tube separate from the RF accelerator. The authors believed that this would provide more adjustability and permit better coupling to be obtained. They did not have sufficient success with that approach, and finally completed the project using a DC accelerator with a unique new scanning system to irradiate the waste.

  20. Separation of transuranium elements from irradiated targets

    SciTech Connect

    Wham, R.M.; Benker, D.E.; Felker, L.K.; Chattin, F.R.

    1993-12-31

    Aluminum targets containing curium/americium oxide are irradiated to produce the transcurium actinides einsteinium, fermium, berkelium, and californium. Recovery of recycle curium/americium and the transcurium elements involves several chemical processing steps to selectively recover those elements and remove fission products. Chemical processing steps developed at the Radiochemical Engineering Development Center (REDC) include aluminum dejacketing, solvent extraction to remove bulk impurities, solvent extraction to remove plutonium, anion exchange to partition curium and transcurium elements from the rare earths, and a second anion exchange cycle to separate americium/curium from the transcurium elements.