40 CFR 63.11147 - What are the standards and compliance requirements for existing sources not using batch copper...

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements for existing sources not using batch copper converters? 63.11147 Section 63.11147 Protection of... Hazardous Air Pollutants for Primary Copper Smelting Area Sources Standards and Compliance Requirements § 63.11147 What are the standards and compliance requirements for existing sources not using batch copper...

40 CFR 63.11147 - What are the standards and compliance requirements for existing sources not using batch copper...

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements for existing sources not using batch copper converters? 63.11147 Section 63.11147 Protection of... Hazardous Air Pollutants for Primary Copper Smelting Area Sources Standards and Compliance Requirements § 63.11147 What are the standards and compliance requirements for existing sources not using batch copper...

40 CFR 434.55 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... performance standards shall be achieved for the discharge of any acid or ferruginous mine drainage subject to... following new source performance standards shall apply to the post-mining areas of all new source coal mines... new source coal mines until SMCRA bond release. Except as provided in 40 CFR 401.17 and §§ 434.61 and...

40 CFR 434.55 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... performance standards shall be achieved for the discharge of any acid or ferruginous mine drainage subject to... following new source performance standards shall apply to the post-mining areas of all new source coal mines... new source coal mines until SMCRA bond release. Except as provided in 40 CFR 401.17 and §§ 434.61 and...

Spectral Radiance of a Large-Area Integrating Sphere Source

PubMed Central

Walker, James H.; Thompson, Ambler

1995-01-01

The radiance and irradiance calibration of large field-of-view scanning and imaging radiometers for remote sensing and surveillance applications has resulted in the development of novel calibration techniques. One of these techniques is the employment of large-area integrating sphere sources as radiance or irradiance secondary standards. To assist the National Aeronautical and Space Administration’s space based ozone measurement program, a commercially available large-area internally illuminated integrating sphere source’s spectral radiance was characterized in the wavelength region from 230 nm to 400 nm at the National Institute of Standards and Technology. Spectral radiance determinations and spatial mappings of the source indicate that carefully designed large-area integrating sphere sources can be measured with a 1 % to 2 % expanded uncertainty (two standard deviation estimate) in the near ultraviolet with spatial nonuniformities of 0.6 % or smaller across a 20 cm diameter exit aperture. A method is proposed for the calculation of the final radiance uncertainties of the source which includes the field of view of the instrument being calibrated. PMID:29151725

40 CFR 63.11407 - Am I subject to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... this subpart if you own or operate a chromium compounds manufacturing facility that is an area source... source. The affected source is each chromium compounds manufacturing facility. (1) An affected source is...

40 CFR 63.11407 - Am I subject to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... this subpart if you own or operate a chromium compounds manufacturing facility that is an area source... source. The affected source is each chromium compounds manufacturing facility. (1) An affected source is...

40 CFR 63.11407 - Am I subject to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... this subpart if you own or operate a chromium compounds manufacturing facility that is an area source... source. The affected source is each chromium compounds manufacturing facility. (1) An affected source is...

40 CFR 63.11407 - Am I subject to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... this subpart if you own or operate a chromium compounds manufacturing facility that is an area source... source. The affected source is each chromium compounds manufacturing facility. (1) An affected source is...

40 CFR 63.11407 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... this subpart if you own or operate a chromium compounds manufacturing facility that is an area source... source. The affected source is each chromium compounds manufacturing facility. (1) An affected source is...

Summary of 2012 Reconsideration Public Comments and Responses for Industrial, Commercial, and Institutional Boilers at Area Sources: National Emission Standards for Hazardous Air Pollutants (NESHAP)

EPA Pesticide Factsheets

This page has a 12/2012 document that provides EPA’s responses to public comments on EPA’s Proposed National Emission Standards for Hazardous Air Pollutants for Area Sources: Industrial, Commercial, and Institutional Boilers and Process Heaters

National Emission Standards for Hazardous Air Pollutants (NESHAP) for Area Source Boilers Tune-up Guides

EPA Pesticide Factsheets

This page contains two tune-up guides for area source boilers for industrial, commercial, and institutional boilers and process heaters. The first guide is for owners and operators, and the second is for technicians for the area source boilers.

40 CFR 63.11430 - What are the standards?

Code of Federal Regulations, 2010 CFR

2010-07-01

... preservative treatment of wood at a new or existing area source. You may use your standard operating procedures... 40 Protection of Environment 14 2010-07-01 2010-07-01 false What are the standards? 63.11430... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED...

40 CFR 63.11430 - What are the standards?

Code of Federal Regulations, 2014 CFR

2014-07-01

... preservative treatment of wood at a new or existing area source. You may use your standard operating procedures... 40 Protection of Environment 15 2014-07-01 2014-07-01 false What are the standards? 63.11430... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED...

40 CFR 63.11430 - What are the standards?

Code of Federal Regulations, 2013 CFR

2013-07-01

... preservative treatment of wood at a new or existing area source. You may use your standard operating procedures... 40 Protection of Environment 15 2013-07-01 2013-07-01 false What are the standards? 63.11430... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED...

40 CFR 63.11430 - What are the standards?

Code of Federal Regulations, 2012 CFR

2012-07-01

... preservative treatment of wood at a new or existing area source. You may use your standard operating procedures... 40 Protection of Environment 15 2012-07-01 2012-07-01 false What are the standards? 63.11430... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED...

40 CFR 63.11430 - What are the standards?

Code of Federal Regulations, 2011 CFR

2011-07-01

... preservative treatment of wood at a new or existing area source. You may use your standard operating procedures... 40 Protection of Environment 14 2011-07-01 2011-07-01 false What are the standards? 63.11430... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED...

40 CFR 63.11623 - What are the testing requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... of the cyclone, dry basis, corrected to standard conditions, g/min; MOUTLET = Mass of particulate... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Prepared Feeds...

40 CFR 434.55 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... standards shall be achieved for the discharge of any acid or ferruginous mine drainage subject to this... source performance standards shall apply to the post-mining areas of all new source coal mines: (a... coal mines until SMCRA bond release. Except as provided in 40 CFR 401.17 and §§ 434.61 and 434.63 (d)(2...

40 CFR 63.11402 - What are the standards and compliance requirements for new and existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false What are the standards and compliance requirements for new and existing sources? 63.11402 Section 63.11402 Protection of Environment ENVIRONMENTAL... Carbon Black Production Area Sources Standards and Compliance Requirements § 63.11402 What are the...

40 CFR 63.11409 - What are the standards?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... capture system that collects the gases and fumes released during the operation of each emissions source...

40 CFR 63.11409 - What are the standards?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... capture system that collects the gases and fumes released during the operation of each emissions source...

40 CFR 63.11409 - What are the standards?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... capture system that collects the gases and fumes released during the operation of each emissions source...

40 CFR 63.11409 - What are the standards?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... capture system that collects the gases and fumes released during the operation of each emissions source...

40 CFR 63.11409 - What are the standards?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources: Chromium... capture system that collects the gases and fumes released during the operation of each emissions source...

40 CFR 63.1191 - What notifications must I submit?

Code of Federal Regulations, 2010 CFR

2010-07-01

... types of sources are subject to the standard: (1) An area source that increases its emissions so that it becomes a major source. (2) A source that has an initial startup before the effective date of the standard. (3) A new or reconstructed source that has an initial startup after the effective date of the...

40 CFR 63.1191 - What notifications must I submit?

Code of Federal Regulations, 2014 CFR

2014-07-01

... types of sources are subject to the standard: (1) An area source that increases its emissions so that it becomes a major source. (2) A source that has an initial startup before the effective date of the standard. (3) A new or reconstructed source that has an initial startup after the effective date of the...

40 CFR 63.11502 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... begins with the initiation of steps as described in a written standard operating procedures (SOP) or... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources...

76 FR 35744 - Amendments to National Emission Standards for Hazardous Air Pollutants for Area Sources: Plating...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-20

.... Regulated sources do not include chromium electroplating and chromium anodizing sources, as those sources are subject to 40 CFR part 63, subpart N, ``Chromium Emissions From Hard and Decorative Chromium Electroplating and Chromium Anodizing Tanks.'' Manufacturing 32, 33 Area source establishments engaged in one or...

40 CFR 63.11428 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Wood Preserving Area Sources Applicability and... operate a wood preserving operation that is an area source of hazardous air pollutant (HAP) emissions. (b) The affected source is each new or existing wood preserving operation. (1) An affected source is...

40 CFR Table 1 to Subpart Wwwwww... - Table 1 to Subpart WWWWWW of Part 63. Applicability of General Provisions to Plating and...

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Applicability of General Provisions to Plating and Polishing Area Sources 1 Table 1 to Subpart WWWWWW of Part 63. Applicability of General Provisions to Plating and Polishing Area Sources Protection of Environment... Pollutants: Area Source Standards for Plating and Polishing Operations Pt. 63, Subpt. WWWWWW, Table 1 Table 1...

40 CFR Table 1 to Subpart Wwwwww... - Table 1 to Subpart WWWWWW of Part 63. Applicability of General Provisions to Plating and...

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Applicability of General Provisions to Plating and Polishing Area Sources 1 Table 1 to Subpart WWWWWW of Part 63. Applicability of General Provisions to Plating and Polishing Area Sources Protection of Environment... Pollutants: Area Source Standards for Plating and Polishing Operations Pt. 63, Subpt. WWWWWW, Table 1 Table 1...

40 CFR 63.11423 - What are the standards and compliance requirements for new and existing sources?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Lead Acid Battery Manufacturing Area Sources Standards and Compliance Requirements § 63.11423 What are.... Fabric filters equipped with a high efficiency particulate air (HEPA) filter or other secondary filter...

40 CFR 63.11423 - What are the standards and compliance requirements for new and existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Lead Acid Battery Manufacturing Area Sources Standards and Compliance Requirements § 63.11423 What are.... Fabric filters equipped with a high efficiency particulate air (HEPA) filter or other secondary filter...

40 CFR 63.11423 - What are the standards and compliance requirements for new and existing sources?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Lead Acid Battery Manufacturing Area Sources Standards and Compliance Requirements § 63.11423 What are.... Fabric filters equipped with a high efficiency particulate air (HEPA) filter or other secondary filter...

40 CFR 63.11423 - What are the standards and compliance requirements for new and existing sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Lead Acid Battery Manufacturing Area Sources Standards and Compliance Requirements § 63.11423 What are.... Fabric filters equipped with a high efficiency particulate air (HEPA) filter or other secondary filter...

40 CFR 63.11423 - What are the standards and compliance requirements for new and existing sources?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Lead Acid Battery Manufacturing Area Sources Standards and Compliance Requirements § 63.11423 What are.... Fabric filters equipped with a high efficiency particulate air (HEPA) filter or other secondary filter...

Analysis of PAEs contaminants in water sources for agriculture, industrial and residential areas from local city district

NASA Astrophysics Data System (ADS)

Chen, Qidan; Chen, Qixian; Wu, Fei; Liao, Jia; Zhao, Xi

2018-02-01

The technology of DEHP and DBP detection by high performance liquid chromatography coupled with ultraviolet detection (HPLC-UV) was developed and applied in analysis of local water sources from agriculture, industrial and residential areas. Under the optimized sample pretreatment and detection conditions, DEHP and DBP were well separated and detected in 4 mins. The detection limit of DBP was 0.002 mg/L and DEHP was 0.006 mg/L, and it meets the Chinese National Standard limitations for drinking water quality. The linear correlation coefficient of DBP and DEHP standard calibration curves was 0.9998 and 0.9995. The linear range of DBP was 0.020 mg/L ∼20.0 mg/L, with the standard deviation of 0.560% ∼5.07%, and the linear range of DEHP was 0.060 mg/L ∼15.0 mg/L, with the standard deviation of 0.546% ∼5.74%. Ten water samples from Jinwan district of Zhuhai in Guangdong province of China were analyzed. However, the PAEs amounts found in the water sources from industrial areas were higher than the agriculture and residential areas, industries grow incredibly fast in the district in recently years and more attention should be paid to the increasing risks of water sources pollution.

Summary of Energy Assessment Requirements under the Area Source Boiler Rule

EPA Pesticide Factsheets

This document provides an overview of the energy assessment requirements for the national emission standards for hazardous air pollutants (NESHAP) for area sources: industrial, commercial and Institutional boilers, 40 CFR Part 63, Subpart JJJJJJ.

California's Ozone-Reduction Strategy for Light Duty Vehicles - An Economic Assessment

DOT National Transportation Integrated Search

1996-01-01

California has adopted an aggressive plan to bring the state into compliance with national ambient air quality standards. California's strategy includes strict emission standards on mobile and stationary sourcs and on area sources such as solvents, p...

Development of a Mobile Tracer Correlation Method for Assessment of Air Emissions from Landfills and Other Area Sources

EPA Science Inventory

Information form the previously approved extended abstract A standardized area source measurement method based on mobile tracer correlation was used for methane emissions assessment in 52 field deployments...

Fact Sheet: Final Rule to Reduce Air Toxics Emissions from Area Source Paints and Allied Products Manufacturing Facilities

EPA Pesticide Factsheets

This page contains a November 2009 fact sheet with information regarding the National Emission Standards for Hazardous Air Pollutants (NESHAP) for Area Sources of Paints and Allied Products Manufacturing.

40 CFR 63.11465 - What are the standards for new and existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Metals Processing Area Sources Standards, Compliance, and Monitoring Requirements § 63.11465 What are the... through a fabric filter or baghouse that achieves a particulate matter (PM) control efficiency of at least... affected source through a fabric filter or baghouse that achieves a PM control efficiency of at least 99.5...

40 CFR 63.11567 - Who implements and enforces this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

...). 2. A high-efficiency air filter or fiber bed filter a. Inlet gas temperature b, andb. Pressure drop...) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt...

40 CFR 131.35 - Colville Confederated Tribes Indian Reservation.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-effective and reasonable best management practices for nonpoint source control. (iii) Where high quality... within areas designated as unique water quality management areas and waters otherwise of exceptional... PROGRAMS WATER QUALITY STANDARDS Federally Promulgated Water Quality Standards § 131.35 Colville...

40 CFR Table 1 to Subpart Gggggg... - Applicability of General Provisions to Primary Zinc Production Area Sources

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 15 2012-07-01 2012-07-01 false Applicability of General Provisions to Primary Zinc Production Area Sources 1 Table 1 to Subpart GGGGGG of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIE...

40 CFR Table 1 to Subpart Gggggg... - Applicability of General Provisions to Primary Zinc Production Area Sources

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 15 2014-07-01 2014-07-01 false Applicability of General Provisions to Primary Zinc Production Area Sources 1 Table 1 to Subpart GGGGGG of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIE...

40 CFR Table 1 to Subpart Gggggg... - Applicability of General Provisions to Primary Zinc Production Area Sources

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 15 2013-07-01 2013-07-01 false Applicability of General Provisions to Primary Zinc Production Area Sources 1 Table 1 to Subpart GGGGGG of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIE...

40 CFR 63.11588 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry Other Requirements and Information § 63.11588 What definitions apply to this subpart? Chemical... by the paints and allied products area source rule (40 CFR part 63, subpart CCCCCCC). Chemical...

40 CFR 63.11588 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry Other Requirements and Information § 63.11588 What definitions apply to this subpart? Chemical... by the paints and allied products area source rule (40 CFR part 63, subpart CCCCCCC). Chemical...

40 CFR 63.11588 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry Other Requirements and Information § 63.11588 What definitions apply to this subpart? Chemical... by the paints and allied products area source rule (40 CFR part 63, subpart CCCCCCC). Chemical...

40 CFR 63.11400 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Carbon Black Production Area Sources... if you own or operate a carbon black production facility that is an area source of hazardous air... units, maintenance wastewater, and equipment components that contain or contact HAP that are associated...

40 CFR 63.11498 - What are the standards and compliance requirements for wastewater systems?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Chemical Manufacturing Area Sources Standards and Compliance Requirements § 63.11498 What are the standards... each wastewater stream using process knowledge, engineering assessment, or test data. Also, you must...

40 CFR 63.11498 - What are the standards and compliance requirements for wastewater systems?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Chemical Manufacturing Area Sources Standards and Compliance Requirements § 63.11498 What are the standards... each wastewater stream using process knowledge, engineering assessment, or test data. Also, you must...

76 FR 80261 - National Emission Standards for Hazardous Air Pollutants: Area Source Standards for Prepared...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-23

... specifications and operating instructions, if available, or standard operating procedures must be developed by... manufacturer's specifications and operating instructions, if available, or standard operating procedures must... operating specifications or standard operating procedures developed by the prepared feeds manufacturer be...

40 CFR 63.11417 - What are the compliance requirements for new and existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Flexible Polyurethane Foam Production and Fabrication Area Sources Standards and Compliance Requirements... a slabstock flexible polyurethane foam production affected source, you must comply with the... affected source, or a loop slitter at a flexible polyurethane foam fabrication affected source you must...

40 CFR 63.11417 - What are the compliance requirements for new and existing sources?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Flexible Polyurethane Foam Production and Fabrication Area Sources Standards and Compliance Requirements... a slabstock flexible polyurethane foam production affected source, you must comply with the... affected source, or a loop slitter at a flexible polyurethane foam fabrication affected source you must...

40 CFR 63.11417 - What are the compliance requirements for new and existing sources?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Flexible Polyurethane Foam Production and Fabrication Area Sources Standards and Compliance Requirements... a slabstock flexible polyurethane foam production affected source, you must comply with the... affected source, or a loop slitter at a flexible polyurethane foam fabrication affected source you must...

40 CFR 63.11417 - What are the compliance requirements for new and existing sources?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Flexible Polyurethane Foam Production and Fabrication Area Sources Standards and Compliance Requirements... a slabstock flexible polyurethane foam production affected source, you must comply with the... affected source, or a loop slitter at a flexible polyurethane foam fabrication affected source you must...

40 CFR 63.11417 - What are the compliance requirements for new and existing sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Flexible Polyurethane Foam Production and Fabrication Area Sources Standards and Compliance Requirements... a slabstock flexible polyurethane foam production affected source, you must comply with the... affected source, or a loop slitter at a flexible polyurethane foam fabrication affected source you must...

75 FR 10184 - National Emission Standards for Hazardous Air Pollutants: Area Source Standards for Paints and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-05

... information and technology exchange in various areas of air pollution control. I. Corrections On December 3... CFR Part 63 Environmental protection, Administrative practice and procedure, Air pollution control... section during the grinding and milling of materials containing compounds of cadmium, chromium, lead, or...

40 CFR 63.11395 - What are the standards and compliance requirements for existing sources?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Modacrylic Fibers Production Area Sources Standards and Compliance Requirements § 63.11395 What are the... enclosure systems that collect the gases and fumes containing acrylonitrile (AN) released from... through a closed vent system to a control device. (b) Except as provided in paragraph (b)(3) of this...

40 CFR 63.11395 - What are the standards and compliance requirements for existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Modacrylic Fibers Production Area Sources Standards and Compliance Requirements § 63.11395 What are the... enclosure systems that collect the gases and fumes containing acrylonitrile (AN) released from... through a closed vent system to a control device. (b) Except as provided in paragraph (b)(3) of this...

Development of Mobile Tracer Correlation Method for Assessment of Air Emissions from Landfills and Other Area Sources

EPA Science Inventory

Abstract - A standardized version of a mobile tracer correlation measurement method was developed and used for assessment of methane emissions from 15 landfills in 56 field deployments from 2009 to 2013. This general area source measurement method uses advances in instrumentation...

76 FR 80314 - National Emission Standards for Hazardous Air Pollutants: Area Source Standards for Prepared...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-23

... operating instructions, if available, or standard operating procedures must be developed by the facility... operating instructions, if available, or standard operating procedures must be developed by the facility... standard operating procedures developed by the prepared feeds manufacturer be required as part of the...

40 CFR 63.11561 - What are my standards and management practices?

Code of Federal Regulations, 2013 CFR

2013-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Standards and Compliance Requirements § 63.11561 What are my standards and management practices? (a) For asphalt processing operations, you must meet the emission limits...

40 CFR 63.11561 - What are my standards and management practices?

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Standards and Compliance Requirements § 63.11561 What are my standards and management practices? (a) For asphalt processing operations, you must meet the emission limits...

40 CFR 63.11561 - What are my standards and management practices?

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Standards and Compliance Requirements § 63.11561 What are my standards and management practices? (a) For asphalt processing operations, you must meet the emission limits...

40 CFR 63.11561 - What are my standards and management practices?

Code of Federal Regulations, 2011 CFR

2011-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Standards and Compliance Requirements § 63.11561 What are my standards and management practices? (a) For asphalt processing operations, you must meet the emission limits...

Open Standards, Open Source, and Open Innovation: Harnessing the Benefits of Openness

ERIC Educational Resources Information Center

Committee for Economic Development, 2006

2006-01-01

Digitization of information and the Internet have profoundly expanded the capacity for openness. This report details the benefits of openness in three areas--open standards, open-source software, and open innovation--and examines the major issues in the debate over whether openness should be encouraged or not. The report explains each of these…

40 CFR 63.11396 - What are the standards and compliance requirements for new sources?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Modacrylic Fibers Production Area Sources Standards and Compliance Requirements § 63.11396 What are the... through a closed vent system to any combination of control devices meeting the requirements for process... (b)(1), (2), or (3) of this section for each fiber spinning line that uses a spin dope produced from...

40 CFR 63.11396 - What are the standards and compliance requirements for new sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Modacrylic Fibers Production Area Sources Standards and Compliance Requirements § 63.11396 What are the... through a closed vent system to any combination of control devices meeting the requirements for process... (b)(1), (2), or (3) of this section for each fiber spinning line that uses a spin dope produced from...

Development of a Mobile Tracer Correlation Method for Assessment of Air Emissions from Landfills and Other Area Sources (Abstract)

EPA Science Inventory

Work toward a standardized version of a mobile tracer correlation measurement method is discussed. The method used for assessment of methane emissions from 15 landfills in 56 field deployments from 2009 to 2013. This general area source measurement method uses advances in instrum...

Area Source Boiler National Emission Standards for Hazardous Air Pollutants (NESHAP), 40 CFR Part 63, Subpart JJJJJJ: Questions and Answers

EPA Pesticide Factsheets

This October 2016 question and answer (Q&A) document is in response to a number of questions the EPA has received from delegated state and local agencies and the regulated community regarding the NESHAP for Area source boilers. Document updates 4/2014 PDF.

Example Owner/Operator Certification for Painter Training Under National Emission Standards for Hazardous Air Pollutant (NESHAP): Area Source Standards for Nine Metal Fabrication and Finishing Source Categories 40 CFR 60 Subpart XXXXXX

EPA Pesticide Factsheets

This example training certification format and any attached training documentation may be used to demonstrate, document and certify successful completion of required training topics under 40 CFR 63.11515(d)(6) for personnel, who spray apply surface coating

A novel method for the activity measurement of large-area beta reference sources.

PubMed

Stanga, D; De Felice, P; Keightley, J; Capogni, M; Ioan, M R

2016-03-01

A novel method has been developed for the activity measurement of large-area beta reference sources. It makes use of two emission rate measurements and is based on the weak dependence between the source activity and the activity distribution for a given value of transmission coefficient. The method was checked experimentally by measuring the activity of two ((60)Co and (137)Cs) large-area reference sources constructed from anodized aluminum foils. Measurement results were compared with the activity values measured by gamma spectrometry. For each source, they agree within one standard uncertainty and also agree within the same limits with the certified values of the source activity. Copyright © 2015 Elsevier Ltd. All rights reserved.

Guidance for creating annual on-road mobile source emission inventories for PM2.5 nonattainment areas for use in SIPs and conformity.

DOT National Transportation Integrated Search

2005-08-01

The purpose of this document is to provide areas that are nonattainment or maintenance for the annual PM2.5 national ambient air quality standard (standard) with guidance on developing annual PM2.5 on-road motor vehicle emissions estimates to m...

Quantification of metal loading to Silver Creek through the Silver Maple Claims area, Park City, Utah, May 2002

USGS Publications Warehouse

Kimball, Briant A.; Johnson, Kevin K.; Runkel, Robert L.; Steiger, Judy I.

2004-01-01

The Silver Maple Claims area along Silver Creek, near Park City, Utah, is administered by the Bureau of Land Management. To quantify possible sources of elevated zinc concentrations in Silver Creek that exceed water-quality standards, the U.S. Geological Survey conducted a mass-loading study in May 2002 along a 1,400-meter reach of Silver Creek that included the Silver Maple Claims area. Additional samples were collected upstream and downstream from the injection reach to investigate other possible sources of zinc and other metals to the stream. Many metals were investigated in the study, but zinc is of particular concern for water-quality standards. The total loading of zinc along the study reach from Park City to Wanship, Utah, was about 49 kilograms per day. The Silver Maple Claims area contributed about 38 percent of this load. The Silver Creek tailings discharge pipe, which empties just inside the Silver Maple Claims area, contributed more than half the load of the Silver Maple Claims area. Substantial zinc loads also were added to Silver Creek downstream from the Silver Maple Claims area. Ground-water discharge upstream from the waste-water treatment plant contributed 20 percent of the total zinc load, and another 17 percent was contributed near the waste-water treatment plant. By identifying the specific areas where zinc and other metal loads are contributed to Silver Creek, it is possible to assess the needs of a remediation plan. For example, removing the tailings from the Silver Maple Claims area could contribute to lowering the zinc concentration in Silver Creek, but without also addressing the loading from the Silver Creek tailings discharge pipe and the ground-water discharge farther downstream, the zinc concentration could not be lowered enough to meet water-quality standards. Additional existing sources of zinc loading downstream from the Silver Maple Claims area could complicate the process of lowering zinc concentration to meet water-quality standards.

40 CFR 63.11645 - What are my mercury emission standards?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 14 2011-07-01 2011-07-01 false What are my mercury emission standards... Area Source Category Standards and Compliance Requirements § 63.11645 What are my mercury emission standards? (a) For existing ore pretreatment processes, you must emit no more than 127 pounds of mercury per...

40 CFR 63.11645 - What are my mercury emission standards?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 15 2012-07-01 2012-07-01 false What are my mercury emission standards... Area Source Category Standards and Compliance Requirements § 63.11645 What are my mercury emission standards? (a) For existing ore pretreatment processes, you must emit no more than 127 pounds of mercury per...

40 CFR 63.11645 - What are my mercury emission standards?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 15 2014-07-01 2014-07-01 false What are my mercury emission standards... Area Source Category Standards and Compliance Requirements § 63.11645 What are my mercury emission standards? (a) For existing ore pretreatment processes, you must emit no more than 127 pounds of mercury per...

40 CFR 63.11645 - What are my mercury emission standards?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 15 2013-07-01 2013-07-01 false What are my mercury emission standards... Area Source Category Standards and Compliance Requirements § 63.11645 What are my mercury emission standards? (a) For existing ore pretreatment processes, you must emit no more than 127 pounds of mercury per...

40 CFR 63.11581 - What are my standards?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry... requirements in paragraph (a) or (b) of this section that apply to you. These standards apply at all times. (a) You must meet one of the emission standards in Table 1 of this subpart and the management practices in...

40 CFR 63.11581 - What are my standards?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry... requirements in paragraph (a) or (b) of this section that apply to you. These standards apply at all times. (a) You must meet one of the emission standards in Table 1 of this subpart and the management practices in...

Fact Sheet: Final Air Toxics Standards for Area Sources in Seven Industry Sectors

EPA Pesticide Factsheets

This fact sheet discusses national emission standards for acrylic and modacrylic fibers production, carbon black production, chemical manufacturing: chromium compounds, flexible polyurethane foam production and fabrication, lead acid battery manufacturing,

40 CFR 63.11467 - What are the initial compliance demonstration requirements for new and existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Pollutants for Secondary Nonferrous Metals Processing Area Sources Standards, Compliance, and Monitoring... for structural integrity and fabric filter condition. You must record the results of the inspection...

Open Data, Open Source and Open Standards in chemistry: The Blue Obelisk five years on

PubMed Central

2011-01-01

Background The Blue Obelisk movement was established in 2005 as a response to the lack of Open Data, Open Standards and Open Source (ODOSOS) in chemistry. It aims to make it easier to carry out chemistry research by promoting interoperability between chemistry software, encouraging cooperation between Open Source developers, and developing community resources and Open Standards. Results This contribution looks back on the work carried out by the Blue Obelisk in the past 5 years and surveys progress and remaining challenges in the areas of Open Data, Open Standards, and Open Source in chemistry. Conclusions We show that the Blue Obelisk has been very successful in bringing together researchers and developers with common interests in ODOSOS, leading to development of many useful resources freely available to the chemistry community. PMID:21999342

75 FR 32682 - National Emission Standards for Hazardous Air Pollutants for Major Sources: Industrial...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-09

... for Existing Sources: Commercial and Industrial Solid Waste Incineration Units; Identification of Non-Hazardous Secondary Materials That Are Solid Waste AGENCY: Environmental Protection Agency. ACTION: Notice... Institutional Boilers located at area sources; and Commercial and Industrial Solid Waste Incineration Units. On...

40 CFR 440.104 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines that... process wastewater to navigable waters from mine areas and mills processes and areas that use dump, heap...

75 FR 9647 - National Emission Standards for Hazardous Air Pollutants for Reciprocating Internal Combustion...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-03

...EPA is promulgating national emission standards for hazardous air pollutants for existing stationary compression ignition reciprocating internal combustion engines that either are located at area sources of hazardous air pollutant emissions or that have a site rating of less than or equal to 500 brake horsepower and are located at major sources of hazardous air pollutant emissions. In addition, EPA is promulgating national emission standards for hazardous air pollutants for existing non-emergency stationary compression ignition engines greater than 500 brake horsepower that are located at major sources of hazardous air pollutant emissions. Finally, EPA is revising the provisions related to startup, shutdown, and malfunction for the engines that were regulated previously by these national emission standards for hazardous air pollutants.

40 CFR 63.11440 - What are the monitoring requirements for new and existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Clay Ceramics Manufacturing Area Sources Standards, Compliance, and Monitoring Requirements § 63.11440... ceramic ware, you must conduct a daily check of the peak firing temperature. If the peak temperature...

Example Annual Certification & Compliance Reports for Sources with and without Visible Emissions Testing: NESHAP Area Source Standards for Nine Metal Fabrication and Finishing Source Categories 40 CFR 63 Subpart XXXXXX

EPA Pesticide Factsheets

This page contains examples of the type of information that must be submitted to fulfill the Notification of Compliance Status requirement of 40 CFR 63, subpart XXXXXX for sources reporting and not reporting visible emissions information.

40 CFR 63.1340 - Applicability and designation of affected sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... CATEGORIES National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing... portland cement plant which is a major source or an area source as defined in § 63.2. (b) The affected... portland cement plant which is a major source; (3) Each raw mill at any portland cement plant which is a...

40 CFR 63.1218 - What are the standards for hydrochloric acid production furnaces that burn hazardous waste?

Code of Federal Regulations, 2013 CFR

2013-07-01

... limits provided by paragraph (a)(5) of this section; (2) For mercury, hydrogen chloride and chlorine gas..., except for an area source as defined under § 63.2, hydrogen chloride and chlorine gas emissions in excess..., except for an area source as defined under § 63.2, hydrogen chloride and chlorine gas emissions in excess...

Games between stakeholders and the payment for ecological services: evidence from the Wuxijiang River reservoir area in China

PubMed Central

2018-01-01

A gambling or “game” phenomenon can be observed in the complex relationship between sources and receptors of ecological compensation among multiple stakeholders. This paper investigates the problem of gambling to determine payment amounts, and details a method to estimate the ecological compensation amount related to water resources in the Wuxijiang River reservoir area in China. Public statistics and first-hand data obtained from a field investigation were used as data sources. Estimation of the source and receptor amount of ecological compensation relevant to the water resource being investigated was achieved using the contingent valuation method (CVM). The ecological compensation object and its benefit and gambling for the Wuxijiang River water source area are also analyzed in this paper. According to the results of a CVM survey, the ecological compensation standard for the Wuxijiang River was determined by the CVM, and the amount of compensation was estimated. Fifteen blocks downstream of the Wuxijiang River and 12 blocks in the water source area were used as samples to administer a survey that estimated the willingness to pay (WTP) and the willingness to accept (WTA) the ecological compensation of Wuxijiang River for both nonparametric and parametric estimation. Finally, the theoretical value of the ecological compensation amount was estimated. Without taking other factors into account, the WTP of residents in the Wuxi River water source was 297.48 yuan per year, while the WTAs were 3864.48 yuan per year. The theoretical standard of ecological compensation is 2294.39–2993.81 yuan per year. Under the parameter estimation of other factors, the WTP of residents in the Wuxi River water source area was 528.72 yuan per year, while the WTA was 1514.04 yuan per year. The theoretical standard of ecological compensation is 4076.25–5434.99 yuan per year. The main factors influencing the WTP ecological compensation in the Wuxi River basin are annual income and age. The main factors affecting WTA are gender and attention to the environment, age, marital status, local birth, and location in the main village. PMID:29568707

Games between stakeholders and the payment for ecological services: evidence from the Wuxijiang River reservoir area in China.

PubMed

Shu, Lin

2018-01-01

A gambling or "game" phenomenon can be observed in the complex relationship between sources and receptors of ecological compensation among multiple stakeholders. This paper investigates the problem of gambling to determine payment amounts, and details a method to estimate the ecological compensation amount related to water resources in the Wuxijiang River reservoir area in China. Public statistics and first-hand data obtained from a field investigation were used as data sources. Estimation of the source and receptor amount of ecological compensation relevant to the water resource being investigated was achieved using the contingent valuation method (CVM). The ecological compensation object and its benefit and gambling for the Wuxijiang River water source area are also analyzed in this paper. According to the results of a CVM survey, the ecological compensation standard for the Wuxijiang River was determined by the CVM, and the amount of compensation was estimated. Fifteen blocks downstream of the Wuxijiang River and 12 blocks in the water source area were used as samples to administer a survey that estimated the willingness to pay (WTP) and the willingness to accept (WTA) the ecological compensation of Wuxijiang River for both nonparametric and parametric estimation. Finally, the theoretical value of the ecological compensation amount was estimated. Without taking other factors into account, the WTP of residents in the Wuxi River water source was 297.48 yuan per year, while the WTAs were 3864.48 yuan per year. The theoretical standard of ecological compensation is 2294.39-2993.81 yuan per year. Under the parameter estimation of other factors, the WTP of residents in the Wuxi River water source area was 528.72 yuan per year, while the WTA was 1514.04 yuan per year. The theoretical standard of ecological compensation is 4076.25-5434.99 yuan per year. The main factors influencing the WTP ecological compensation in the Wuxi River basin are annual income and age. The main factors affecting WTA are gender and attention to the environment, age, marital status, local birth, and location in the main village.

10 CFR 20.1601 - Control of access to high radiation areas.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Control of access to high radiation areas. 20.1601 Section 20.1601 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1601 Control of access to high radiation areas. (a...

10 CFR 20.1601 - Control of access to high radiation areas.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Control of access to high radiation areas. 20.1601 Section 20.1601 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1601 Control of access to high radiation areas. (a...

10 CFR 20.1601 - Control of access to high radiation areas.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Control of access to high radiation areas. 20.1601 Section 20.1601 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1601 Control of access to high radiation areas. (a...

10 CFR 20.1601 - Control of access to high radiation areas.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Control of access to high radiation areas. 20.1601 Section 20.1601 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1601 Control of access to high radiation areas. (a...

10 CFR 20.1601 - Control of access to high radiation areas.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Control of access to high radiation areas. 20.1601 Section 20.1601 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1601 Control of access to high radiation areas. (a...

A GIS-based time-dependent seismic source modeling of Northern Iran

NASA Astrophysics Data System (ADS)

Hashemi, Mahdi; Alesheikh, Ali Asghar; Zolfaghari, Mohammad Reza

2017-01-01

The first step in any seismic hazard study is the definition of seismogenic sources and the estimation of magnitude-frequency relationships for each source. There is as yet no standard methodology for source modeling and many researchers have worked on this topic. This study is an effort to define linear and area seismic sources for Northern Iran. The linear or fault sources are developed based on tectonic features and characteristic earthquakes while the area sources are developed based on spatial distribution of small to moderate earthquakes. Time-dependent recurrence relationships are developed for fault sources using renewal approach while time-independent frequency-magnitude relationships are proposed for area sources based on Poisson process. GIS functionalities are used in this study to introduce and incorporate spatial-temporal and geostatistical indices in delineating area seismic sources. The proposed methodology is used to model seismic sources for an area of about 500 by 400 square kilometers around Tehran. Previous researches and reports are studied to compile an earthquake/fault catalog that is as complete as possible. All events are transformed to uniform magnitude scale; duplicate events and dependent shocks are removed. Completeness and time distribution of the compiled catalog is taken into account. The proposed area and linear seismic sources in conjunction with defined recurrence relationships can be used to develop time-dependent probabilistic seismic hazard analysis of Northern Iran.

40 CFR 63.11424 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false [Reserved] 63.11424 Section 63.11424 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL... Standards for Hazardous Air Pollutants for Lead Acid Battery Manufacturing Area Sources Standards and...

40 CFR 63.11158 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

...? 63.11158 Section 63.11158 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Secondary Copper Smelting Area...

40 CFR 63.11158 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

...? 63.11158 Section 63.11158 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Secondary Copper Smelting Area...

40 CFR 63.11158 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

...? 63.11158 Section 63.11158 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Secondary Copper Smelting Area...

40 CFR 63.11403 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false [Reserved] 63.11403 Section 63.11403 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL... Standards for Hazardous Air Pollutants for Carbon Black Production Area Sources Standards and Compliance...

40 CFR 63.11457 - What are the recordkeeping requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area... calibration and maintenance records. (7) For each bag leak detection system, the records specified in...

40 CFR 63.11457 - What are the recordkeeping requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area... calibration and maintenance records. (7) For each bag leak detection system, the records specified in...

40 CFR 63.11457 - What are the recordkeeping requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area... calibration and maintenance records. (7) For each bag leak detection system, the records specified in...

40 CFR 63.11457 - What are the recordkeeping requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area... calibration and maintenance records. (7) For each bag leak detection system, the records specified in...

[Evaluation of environmental conditions: air, water and soil in areas of mining activity in Boyacá, Colombia].

PubMed

Agudelo-Calderón, Carlos A; Quiroz-Arcentales, Leonardo; García-Ubaque, Juan C; Robledo-Martínez, Rocío; García-Ubaque, Cesar A

2016-02-01

Objectives To determine concentrations of PM10, mercury and lead in indoor air of homes, water sources and soil in municipalities near mining operations. Method 6 points were evaluated in areas of influence and 2 in control areas. For measurements of indoor air, we used the NIOSH 600 method (PM10), NIOSH 6009 (mercury) and NIOSH 7300 (lead). For water analysis we used the IDEAM Guide for monitoring discharges. For soil analysis, we used the cold vapor technique (mercury) and atomic absorption (lead). Results In almost all selected households, the average PM10 and mercury concentrations in indoor air exceeded applicable air quality standards. Concentrations of lead were below standard levels. In all water sources, high concentrations of lead were found and in some places within the mining areas, high levels of iron, aluminum and mercury were also found. In soil, mercury concentrations were below the detection level and for lead, differences between the monitored points were observed. Conclusions The results do not establish causal relationships between mining and concentration of these pollutants in the evaluated areas because of the multiplicity of sources in the area. However, such studies provide important information, useful to agents of the environmental health system and researchers. Installation of networks for environmental monitoring to obtain continuous reports is suggested.

Imminent Danger Pay: Actions Needed Regarding Pay Designations in the U.S. Central Command Area of Responsibility

DTIC Science & Technology

2014-01-30

results of previous audits conducted on the data systems 1The source of this review is the Senate...locations within the CENTCOM area of responsibility. We conducted this performance audit from December 2012 to January 2014 in accordance with...generally accepted government auditing standards. Those standards require that we plan and perform the audit to obtain sufficient, appropriate evidence to

77 FR 75739 - National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-21

...On January 30, 2012, the EPA proposed revisions to several provisions of the final National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources. The proposed revisions were made, in part, in response to a petition for reconsideration received by the Administrator following the promulgation of the October 29, 2009, final rule (``2009 final rule''). In this action, the EPA is finalizing those amendments, lifting the stay of the title V permit requirement issued on March 14, 2011, and lifting the stay of the final rule issued on October 25, 2012. In addition, this final action includes revisions to the EPA's approach for addressing malfunctions and standards applicable during startup and shutdown periods. This final action also includes amendments and technical corrections to the final rule to clarify applicability and compliance issues raised by stakeholders subject to the 2009 final rule. The revisions to the final rule do not reduce the level of environmental protection or emissions control on sources regulated by this rule but provide flexibility and clarity to improve implementation. This action also extends the compliance date for existing sources and the EPA's final response to all issues raised in the petition for reconsideration.

40 CFR 63.11562 - What are my initial compliance requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Standards and Compliance Requirements § 63.11562 What are my initial compliance requirements? (a) For asphalt processing operations, you must: (1) Demonstrate initial...

40 CFR 63.11562 - What are my initial compliance requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Standards and Compliance Requirements § 63.11562 What are my initial compliance requirements? (a) For asphalt processing operations, you must: (1) Demonstrate initial...

40 CFR 63.11562 - What are my initial compliance requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Standards and Compliance Requirements § 63.11562 What are my initial compliance requirements? (a) For asphalt processing operations, you must: (1) Demonstrate initial...

40 CFR 63.11562 - What are my initial compliance requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Standards and Compliance Requirements § 63.11562 What are my initial compliance requirements? (a) For asphalt processing operations, you must: (1) Demonstrate initial...

40 CFR 63.11562 - What are my initial compliance requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Standards and Compliance Requirements § 63.11562 What are my initial compliance requirements? (a) For asphalt processing operations, you must: (1) Demonstrate initial...

Effect of mercury and arsenic from industrial effluents on the drinking water and comparison of the water quality of polluted and non-polluted areas: a case study of Peshawar and Lower Dir.

PubMed

Ishaq, M; Jan, F Akbar; Khan, Murad Ali; Ihsanullah, I; Ahmad, I; Shakirullah, M; Roohullah

2013-02-01

The purpose of the present study was to find out the sources of mercury and arsenic pollution of water in the industrial area of Peshawar, the capital of Khyber Pakhtunkhwa, Pakistan. Samples of effluents, mud, and water were collected from the target area (industrial area of Peshawar), the area of water supply source, and from the less polluted area, the Lower Dir district, as the control. Hg was determined by the cold vapor generation technique, while arsenic was determined using the electrothermal atomic absorption technique. Data of the water from the industrial area were compared with that of the source area, control area, as well as with the WHO and some international drinking water quality standards. The results show that some parameters, i.e., TDS, DO, pH, and hardness, were more than the permissible limits. Textile and glass industries were found to be the major sources of Hg and As pollution. Downstream dilution of these contaminants was also observed.

10 CFR 20.1602 - Control of access to very high radiation areas.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Control of access to very high radiation areas. 20.1602 Section 20.1602 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1602 Control of access to very high radiation areas...

10 CFR 20.1602 - Control of access to very high radiation areas.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Control of access to very high radiation areas. 20.1602 Section 20.1602 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1602 Control of access to very high radiation areas...

10 CFR 20.1602 - Control of access to very high radiation areas.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Control of access to very high radiation areas. 20.1602 Section 20.1602 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1602 Control of access to very high radiation areas...

10 CFR 20.1602 - Control of access to very high radiation areas.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Control of access to very high radiation areas. 20.1602 Section 20.1602 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1602 Control of access to very high radiation areas...

10 CFR 20.1602 - Control of access to very high radiation areas.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Control of access to very high radiation areas. 20.1602 Section 20.1602 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Control of Exposure From External Sources in Restricted Areas § 20.1602 Control of access to very high radiation areas...

40 CFR Table 4 to Subpart Zzzzz of... - Compliance Certifications for New and Existing Affected Sources Classified as Large Iron and...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Existing Affected Sources Classified as Large Iron and Steel Foundries 4 Table 4 to Subpart ZZZZZ of Part... Emission Standards for Hazardous Air Pollutants for Iron and Steel Foundries Area Sources Pt. 63, Subpt... Affected Sources Classified as Large Iron and Steel Foundries As required by § 63.10900(b), your...

40 CFR Table 4 to Subpart Zzzzz of... - Compliance Certifications for New and Existing Affected Sources Classified as Large Iron and...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Existing Affected Sources Classified as Large Iron and Steel Foundries 4 Table 4 to Subpart ZZZZZ of Part... Emission Standards for Hazardous Air Pollutants for Iron and Steel Foundries Area Sources Pt. 63, Subpt... Affected Sources Classified as Large Iron and Steel Foundries As required by § 63.10900(b), your...

40 CFR Table 4 to Subpart Zzzzz of... - Compliance Certifications for New and Existing Affected Sources Classified as Large Iron and...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Existing Affected Sources Classified as Large Iron and Steel Foundries 4 Table 4 to Subpart ZZZZZ of Part... Emission Standards for Hazardous Air Pollutants for Iron and Steel Foundries Area Sources Pt. 63, Subpt... Affected Sources Classified as Large Iron and Steel Foundries As required by § 63.10900(b), your...

40 CFR Table 4 to Subpart Zzzzz of... - Compliance Certifications for New and Existing Affected Sources Classified as Large Iron and...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Existing Affected Sources Classified as Large Iron and Steel Foundries 4 Table 4 to Subpart ZZZZZ of Part... Emission Standards for Hazardous Air Pollutants for Iron and Steel Foundries Area Sources Pt. 63, Subpt... Affected Sources Classified as Large Iron and Steel Foundries As required by § 63.10900(b), your...

40 CFR Table 4 to Subpart Zzzzz of... - Compliance Certifications for New and Existing Affected Sources Classified as Large Iron and...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Existing Affected Sources Classified as Large Iron and Steel Foundries 4 Table 4 to Subpart ZZZZZ of Part... Emission Standards for Hazardous Air Pollutants for Iron and Steel Foundries Area Sources Pt. 63, Subpt... Affected Sources Classified as Large Iron and Steel Foundries As required by § 63.10900(b), your...

Black Swan Event Assessment for Fort Leonard Wood, Missouri

DTIC Science & Technology

2016-03-01

FEMA standards category and using ASCE 7-05. (Source: FEMA.) ................ 16 Figure 9. Estimated trajectory and impact area of the Joplin tornado in...Missouri on May 22, 2011. (Source: U.S. Army Corps of Engineers, Kansas City District.) .............. 18 Figure 10. Tornado intensities and path...near Fort Leonard Wood, Missouri. (Source: Tornado History Project webpage

Source Monitoring 15 Years Later: What Have We Learned from fMRI about the Neural Mechanisms of Source Memory?

ERIC Educational Resources Information Center

Mitchell, Karen J.; Johnson, Marcia K.

2009-01-01

Focusing primarily on functional magnetic resonance imaging (fMRI), this article reviews evidence regarding the roles of subregions of the medial temporal lobes, prefrontal cortex, posterior representational areas, and parietal cortex in source memory. In addition to evidence from standard episodic memory tasks assessing accuracy for neutral…

75 FR 6473 - Primary National Ambient Air Quality Standards for Nitrogen Dioxide

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-09

... review, however, some areas could be classified as non-attainment. Certain States will be required to... sources of NO X emissions are on-road mobile sources, electricity generating units, and non-road mobile... tracking. 2. NO 2 Air Quality and Gradients Around Roadways On-road and non-road mobile sources account for...

DEVELOPMENT OF A MODEL FOR REAL TIME CO CONCENTRATIONS NEAR ROADWAYS

EPA Science Inventory

Although emission standards for mobile sources continue to be tightened, tailpipe emissions in urban areas continue to be a major source of human exposure to air toxics. Current human exposure models using simplified assumptions based on fixed air monitoring stations and region...

40 CFR 63.545 - What are my standards for fugitive dust sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (4) Battery storage area. (5) Equipment maintenance. (6) Material storage areas. (7) Material... achieve 99.97 percent capture efficiency for 0.3 micron particles in a manner that does not generate... 40 CFR 302.4). (4) Battery storage areas. You must inspect any batteries that are not stored in a...

40 CFR 63.545 - What are my standards for fugitive dust sources?

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (4) Battery storage area. (5) Equipment maintenance. (6) Material storage areas. (7) Material... achieve 99.97 percent capture efficiency for 0.3 micron particles in a manner that does not generate... 40 CFR 302.4). (4) Battery storage areas. You must inspect any batteries that are not stored in a...

40 CFR 63.545 - What are my standards for fugitive dust sources?

Code of Federal Regulations, 2014 CFR

2014-07-01

.... (4) Battery storage area. (5) Equipment maintenance. (6) Material storage areas. (7) Material... achieve 99.97 percent capture efficiency for 0.3 micron particles in a manner that does not generate... 40 CFR 302.4). (4) Battery storage areas. You must inspect any batteries that are not stored in a...

Nitrogen Control Through Decentralized Wastewater Treatment: Process Performance and Alternative Management Strategies

EPA Science Inventory

Decentralized or onsite wastewater treatment (OWT) systems have long been implicated in being a major source of N inputs to surface and ground waters and numerous regulatory bodies have promulgated strict total N (TN) effluent standards in N-sensitive areas. These standards, howe...

[Ischemic heart disease prevalence estimated using a standard algorithm based on electronic health data in various areas of Italy].

PubMed

Balzi, Daniela; Barchielli, Alessandro; Battistella, Giuseppe; Gnavi, Roberto; Inio, Andrea; Tessari, Roberta; Picariello, Roberta; Canova, Cristina; Simonato, Lorenzo

2008-01-01

to define an algorithm to estimate prevalence of ischemic heart disease from health administrative datasets. four Italian areas: Venezia, Treviso, Torino, Firenze. resident population in the four areas in the period 2002-2004 (only 2003 for Firenze) for a total of 2,350,000 inhabitants in 2003. annual crude and standardized prevalence rate (x100 inhabitants), 95% confidence intervals by area. Quality (comparability and coherence) indicators are also reported the algorithm is based on record linkage of hospital discharges (SDO), pharmacological prescriptions (PF), exemptions from health-tax exemptions (ET) and causes of mortality (CM). From SDO we extracted discharges for ICD9-CM codes 410*-414* in all diagnoses in the estimation year and during the four years immediately preceding. We selected from PF subjects with at least two prescriptions of organic nitrates (ATC = C01DA*) in the estimation year. From ET subjects with a new exemption for ischemic heart disease (002.414) or who obtained exemption in the three years preceding, were selected. We also considered all deaths in the year for ischemic heart disease (ICD9 CM 410-414). Cases were defined as ischemic heart disease prevalent cases if they were extracted at least once from one of the datasets and if they were alive on January 1 of the estimation year. estimated crude prevalence ranges from 2.5 to 4%. The standardized prevalence led to a narrower range of values (2.8-3.3%). Venezia and Firenze show a higher standardized prevalence in both sexes (men 4.7% and 4.4%; women 2.3% and 2.2% respectively); Treviso and Torino present a lower standardized prevalence (men: 3.9%; women: 1.9%). The hospital discharges are the main source to identify prevalent subjects (34-48% of subjects are solely identified by SDO), pharmacological prescriptions are a relevant source in Firenze and Torino (27-28%), while they are less relevant in Venezia and Treviso (13-15%). ET shows a different contribution to prevalent case identification in the four areas: Venezia (8%), Treviso (3.2%), Firenze (1.3%), whereas in Torino this source was not available at all. Subjects classified as prevalent cases only through causes of death are less than 2%. The percentage of subjects simultaneously identified by multiple sources is high in Venezia (43%) and low in Torino (30%). patterns in use of pharmaceuticals and exemptions from prescription charges appear to be heterogeneous in the different areas under study. These two aspects make a proper comparison between areas difficult. The algorithm could be applied only in areas with a similar use of organic nitrates and with a good comparability of the exemptions dataset.

10 CFR 60.41 - Standards for issuance of a license.

Code of Federal Regulations, 2010 CFR

2010-01-01

... REPOSITORIES Licenses License Issuance and Amendment § 60.41 Standards for issuance of a license. A license to receive and possess source, special nuclear, or byproduct material at a geologic repository operations area may be issued by the Commission upon finding that: (a) Construction of the geologic repository...

40 CFR 60.757 - Reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... current amount of solid waste-in-place and the estimated waste acceptance rate for each year of the 5...) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Municipal Solid Waste... areas where solid waste may be landfilled according to the permit issued by the State, local, or tribal...

40 CFR 60.757 - Reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... current amount of solid waste-in-place and the estimated waste acceptance rate for each year of the 5...) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Municipal Solid Waste... areas where solid waste may be landfilled according to the permit issued by the State, local, or tribal...

40 CFR 60.757 - Reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... current amount of solid waste-in-place and the estimated waste acceptance rate for each year of the 5...) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Municipal Solid Waste... areas where solid waste may be landfilled according to the permit issued by the State, local, or tribal...

40 CFR 60.757 - Reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... current amount of solid waste-in-place and the estimated waste acceptance rate for each year of the 5...) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Municipal Solid Waste... areas where solid waste may be landfilled according to the permit issued by the State, local, or tribal...

40 CFR 60.757 - Reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... current amount of solid waste-in-place and the estimated waste acceptance rate for each year of the 5...) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Municipal Solid Waste... areas where solid waste may be landfilled according to the permit issued by the State, local, or tribal...

49 CFR 571.111 - Standard No. 111; Rear visibility.

Code of Federal Regulations, 2014 CFR

2014-10-01

... mirror that reflect images, excluding the mirror rim or mounting brackets. Environmental test fixture... defined in S15. Rearview image means a visual image, detected by means of a single source, of the area... function of producing the rearview image as required under this standard. Small manufacturer means an...

40 CFR 63.11559 - Am I subject to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt... are subject to this subpart if you own or operate an asphalt processing operation and/or asphalt... paragraphs (b)(1) and (b)(2) of this section. (1) Asphalt processing. The affected source for asphalt...

40 CFR 63.11559 - Am I subject to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt... are subject to this subpart if you own or operate an asphalt processing operation and/or asphalt... paragraphs (b)(1) and (b)(2) of this section. (1) Asphalt processing. The affected source for asphalt...

40 CFR 63.11559 - Am I subject to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt... are subject to this subpart if you own or operate an asphalt processing operation and/or asphalt... paragraphs (b)(1) and (b)(2) of this section. (1) Asphalt processing. The affected source for asphalt...

40 CFR 63.11559 - Am I subject to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt... are subject to this subpart if you own or operate an asphalt processing operation and/or asphalt... paragraphs (b)(1) and (b)(2) of this section. (1) Asphalt processing. The affected source for asphalt...

40 CFR 63.11559 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt... are subject to this subpart if you own or operate an asphalt processing operation and/or asphalt... paragraphs (b)(1) and (b)(2) of this section. (1) Asphalt processing. The affected source for asphalt...

40 CFR 63.11640 - Am I subject to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production Area... subject to this subpart if you own or operate a gold mine ore processing and production facility as... source. The affected sources are each collection of “ore pretreatment processes” at a gold mine ore...

40 CFR 63.11640 - Am I subject to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production Area... subject to this subpart if you own or operate a gold mine ore processing and production facility as... source. The affected sources are each collection of “ore pretreatment processes” at a gold mine ore...

40 CFR 63.11640 - Am I subject to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production Area... subject to this subpart if you own or operate a gold mine ore processing and production facility as... source. The affected sources are each collection of “ore pretreatment processes” at a gold mine ore...

40 CFR 63.11640 - Am I subject to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production Area... subject to this subpart if you own or operate a gold mine ore processing and production facility as... source. The affected sources are each collection of “ore pretreatment processes” at a gold mine ore...

Countries of the World and International Organizations: Sources of Information

DTIC Science & Technology

2007-01-08

provides business addresses worldwide by geographical areas and by standard industrial classification (SIC) codes. Maps Map Catalog (New York, Tilden...Francisco. These offices are often excellent sources of free printed matter — brochures, maps, posters, etc. A directory of tourism offices worldwide is...Peterson’s Guides, Inc.). Published irregularly, these sources offer information by field of work (agriculture, business and industry , teaching English

Using a Divided Bar Apparatus to Measure Thermal Conductivity of Samples of Odd Sizes and Shapes

NASA Astrophysics Data System (ADS)

Crowell, J. "; Gosnold, W. D.

2012-12-01

Standard procedure for measuring thermal conductivity using a divided bar apparatus requires a sample that has the same surface dimensions as the heat sink/source surface in the divided bar. Heat flow is assumed to be constant throughout the column and thermal conductivity (K) is determined by measuring temperatures (T) across the sample and across standard layers and using the basic relationship Ksample=(Kstandard*(ΔT1+ΔT2)/2)/(ΔTsample). Sometimes samples are not large enough or of correct proportions to match the surface of the heat sink/source, however using the equations presented here the thermal conductivity of these samples can still be measured with a divided bar. Measurements were done on the UND Geothermal Laboratories stationary divided bar apparatus (SDB). This SDB has been designed to mimic many in-situ conditions, with a temperature range of -20C to 150C and a pressure range of 0 to 10,000 psi for samples with parallel surfaces and 0 to 3000 psi for samples with non-parallel surfaces. The heat sink/source surfaces are copper disks and have a surface area of 1,772 mm2 (2.74 in2). Layers of polycarbonate 6 mm thick with the same surface area as the copper disks are located in the heat sink and in the heat source as standards. For this study, all samples were prepared from a single piece of 4 inch limestone core. Thermal conductivities were measured for each sample as it was cut successively smaller. The above equation was adjusted to include the thicknesses (Th) of the samples and the standards and the surface areas (A) of the heat sink/source and of the sample Ksample=(Kstandard*Astandard*Thsample*(ΔT1+ΔT3))/(ΔTsample*Asample*2*Thstandard). Measuring the thermal conductivity of samples of multiple sizes, shapes, and thicknesses gave consistent values for samples with surfaces as small as 50% of the heat sink/source surface, regardless of the shape of the sample. Measuring samples with surfaces smaller than 50% of the heat sink/source surface resulted in thermal conductivity values which were too high. The cause of the error with the smaller samples is being examined as is the relationship between the amount of error in the thermal conductivity and the difference in surface areas. As more measurements are made an equation to mathematically correct for the error is being developed on in case a way to physically correct the problem cannot be determined.

75 FR 41991 - Amendments to National Emission Standards for Hazardous Air Pollutants: Area Source Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-20

... Technology Transfer and Advancement Act Section 12(d) of the National Technology Transfer and Advancement Act... confidential business information (CBI) or other information whose disclosure is restricted by statute. Do not... Concerning Regulations That Significantly Affect Energy Supply, Distribution, or Use I. National Technology...

40 CFR 434.30 - Applicability; description of the acid or ferruginous mine drainage subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... SOURCE CATEGORY BPT, BAT, BCT LIMITATIONS AND NEW SOURCE PERFORMANCE STANDARDS Acid or Ferruginous Mine Drainage § 434.30 Applicability; description of the acid or ferruginous mine drainage subcategory. The provisions of this subpart are applicable to acid or ferruginous mine drainage from an active mining area...

40 CFR 434.30 - Applicability; description of the acid or ferruginous mine drainage subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... SOURCE CATEGORY BPT, BAT, BCT LIMITATIONS AND NEW SOURCE PERFORMANCE STANDARDS Acid or Ferruginous Mine Drainage § 434.30 Applicability; description of the acid or ferruginous mine drainage subcategory. The provisions of this subpart are applicable to acid or ferruginous mine drainage from an active mining area...

40 CFR 434.30 - Applicability; description of the acid or ferruginous mine drainage subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... SOURCE CATEGORY BPT, BAT, BCT LIMITATIONS AND NEW SOURCE PERFORMANCE STANDARDS Acid or Ferruginous Mine Drainage § 434.30 Applicability; description of the acid or ferruginous mine drainage subcategory. The provisions of this subpart are applicable to acid or ferruginous mine drainage from an active mining area...

40 CFR 63.11452 - What are the performance test requirements for new and existing sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

... production rate for the performance test, kilograms (tons) of glass produced per hour. (v) Calculate the 3... = Average glass production rate for the performance test, kilograms (tons) of glass produced per hour. (v... Glass Manufacturing Area Sources Standards, Compliance, and Monitoring Requirements § 63.11452 What are...

40 CFR 63.11452 - What are the performance test requirements for new and existing sources?

Code of Federal Regulations, 2012 CFR

2012-07-01

... production rate for the performance test, kilograms (tons) of glass produced per hour. (v) Calculate the 3... = Average glass production rate for the performance test, kilograms (tons) of glass produced per hour. (v... Glass Manufacturing Area Sources Standards, Compliance, and Monitoring Requirements § 63.11452 What are...

40 CFR 63.11452 - What are the performance test requirements for new and existing sources?

Code of Federal Regulations, 2014 CFR

2014-07-01

... production rate for the performance test, kilograms (tons) of glass produced per hour. (v) Calculate the 3... = Average glass production rate for the performance test, kilograms (tons) of glass produced per hour. (v... Glass Manufacturing Area Sources Standards, Compliance, and Monitoring Requirements § 63.11452 What are...

40 CFR 63.11452 - What are the performance test requirements for new and existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... production rate for the performance test, kilograms (tons) of glass produced per hour. (v) Calculate the 3... = Average glass production rate for the performance test, kilograms (tons) of glass produced per hour. (v... Glass Manufacturing Area Sources Standards, Compliance, and Monitoring Requirements § 63.11452 What are...

40 CFR 63.11452 - What are the performance test requirements for new and existing sources?

Code of Federal Regulations, 2011 CFR

2011-07-01

... production rate for the performance test, kilograms (tons) of glass produced per hour. (v) Calculate the 3... = Average glass production rate for the performance test, kilograms (tons) of glass produced per hour. (v... Glass Manufacturing Area Sources Standards, Compliance, and Monitoring Requirements § 63.11452 What are...

40 CFR 63.11420 - Who implements and enforces this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11420 Who...

40 CFR 63.11420 - Who implements and enforces this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11420 Who...

40 CFR 63.11420 - Who implements and enforces this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11420 Who...

40 CFR 63.11420 - Who implements and enforces this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11420 Who...

40 CFR 63.11420 - Who implements and enforces this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11420 Who...

The role of open-source software in innovation and standardization in radiology.

PubMed

Erickson, Bradley J; Langer, Steve; Nagy, Paul

2005-11-01

The use of open-source software (OSS), in which developers release the source code to applications they have developed, is popular in the software industry. This is done to allow others to modify and improve software (which may or may not be shared back to the community) and to allow others to learn from the software. Radiology was an early participant in this model, supporting OSS that implemented the ACR-National Electrical Manufacturers Association (now Digital Imaging and Communications in Medicine) standard for medical image communications. In radiology and in other fields, OSS has promoted innovation and the adoption of standards. Popular OSS is of high quality because access to source code allows many people to identify and resolve errors. Open-source software is analogous to the peer-review scientific process: one must be able to see and reproduce results to understand and promote what is shared. The authors emphasize that support for OSS need not threaten vendors; most vendors embrace and benefit from standards. Open-source development does not replace vendors but more clearly defines their roles, typically focusing on areas in which proprietary differentiators benefit customers and on professional services such as implementation planning and service. Continued support for OSS is essential for the success of our field.

Source apportion of atmospheric particulate matter: a joint Eulerian/Lagrangian approach.

PubMed

Riccio, A; Chianese, E; Agrillo, G; Esposito, C; Ferrara, L; Tirimberio, G

2014-12-01

PM2.5 samples were collected during an annual monitoring campaign (January 2012-January 2013) in the urban area of Naples, one of the major cities in Southern Italy. Samples were collected by means of a standard gravimetric sampler (Tecora Echo model) and characterized from a chemical point of view by ion chromatography. As a result, 143 samples together with their ionic composition have been collected. We extend traditional source apportionment techniques, usually based on multivariate factor analysis, interpreting the chemical analysis results within a Lagrangian framework. The Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT) model was used, providing linkages to the source regions in the upwind areas. Results were analyzed in order to quantify the relative weight of different source types/areas. Model results suggested that PM concentrations are strongly affected not only by local emissions but also by transboundary emissions, especially from the Eastern and Northern European countries and African Saharan dust episodes.

40 CFR 63.11418 - What General Provisions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11418 What General...

40 CFR 63.11418 - What General Provisions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11418 What General...

40 CFR 63.11418 - What General Provisions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11418 What General...

40 CFR 63.11418 - What General Provisions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11418 What General...

40 CFR 63.11418 - What General Provisions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production and Fabrication Area Sources Other Requirements and Information § 63.11418 What General...

75 FR 42030 - Amendments to National Emission Standards for Hazardous Air Pollutants: Area Source Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-20

.... National Technology Transfer Advancement Act J. Executive Order 12898: Federal Actions to Address..., or use of energy. I. National Technology Transfer and Advancement Act Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (``NTTAA''), Public Law 104-113 (15 U.S.C. 272 note) directs...

75 FR 28227 - National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-20

... published a proposed rule for mercury emissions from the gold mine ore processing and production area source... proposed rule (75 FR 22470). Several parties requested that EPA extend the comment period. EPA has granted...-AP48 National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production...

40 CFR 63.1340 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORIES National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing... subpart apply to each new and existing portland cement plant which is a major source or an area source as... this part; (2) Each clinker cooler at any portland cement plant; (3) Each raw mill at any portland...

40 CFR 63.1340 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2011 CFR

2011-07-01

... CATEGORIES National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing... subpart apply to each new and existing portland cement plant which is a major source or an area source as... this part; (2) Each clinker cooler at any portland cement plant; (3) Each raw mill at any portland...

40 CFR 63.11455 - What are the continuous compliance requirements for new and existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Glass Manufacturing Area Sources Standards, Compliance, and Monitoring Requirements § 63.11455 What are... pollution control and monitoring equipment, according to the provisions in § 63.6(e)(1)(i). (c) For each... as specified in your approved alternative monitoring plan. (2) For each new affected furnace that is...

Investigating scintillometer source areas

NASA Astrophysics Data System (ADS)

Perelet, A. O.; Ward, H. C.; Pardyjak, E.

2017-12-01

Scintillometry is an indirect ground-based method for measuring line-averaged surface heat and moisture fluxes on length scales of 0.5 - 10 km. These length scales are relevant to urban and other complex areas where setting up traditional instrumentation like eddy covariance is logistically difficult. In order to take full advantage of scintillometry, a better understanding of the flux source area is needed. The source area for a scintillometer is typically calculated as a convolution of point sources along the path. A weighting function is then applied along the path to compensate for a total signal contribution that is biased towards the center of the beam path, and decreasing near the beam ends. While this method of calculating the source area provides an estimate of the contribution of the total flux along the beam, there are still questions regarding the physical meaning of the weighted source area. These questions are addressed using data from an idealized experiment near the Salt Lake City International Airport in northern Utah, U.S.A. The site is a flat agricultural area consisting of two different land uses. This simple heterogeneity in the land use facilitates hypothesis testing related to source areas. Measurements were made with a two wavelength scintillometer system spanning 740 m along with three standard open-path infrared gas analyzer-based eddy-covariance stations along the beam path. This configuration allows for direct observations of fluxes along the beam and comparisons to the scintillometer average. The scintillometer system employed measures the refractive index structure parameter of air for two wavelengths of electromagnetic radiation, 880 μm and 1.86 cm to simultaneously estimate path-averaged heat and moisture fluxes, respectively. Meteorological structure parameters (CT2, Cq2, and CTq) as well as surface fluxes are compared for various amounts of source area overlap between eddy covariance and scintillometry. Additionally, surface properties from LANDSAT 7 & 8 are used to help understand source area composition for different times throughout the experiment.

40 CFR 63.11565 - What general provisions sections apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information § 63.11565 What general...

40 CFR 63.11565 - What general provisions sections apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information § 63.11565 What general...

40 CFR 63.11565 - What general provisions sections apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information § 63.11565 What general...

40 CFR 63.11565 - What general provisions sections apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information § 63.11565 What general...

40 CFR 63.11565 - What general provisions sections apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information § 63.11565 What general...

Pollution of water sources and removal of pollutants by advanced drinking-water treatment in China.

PubMed

Wang, L; Wang, B

2000-01-01

The pollution of water resources and drinking water sources in China is described in this paper with basic data. About 90% of surface waters and over 60% of drinking water sources in urban areas have been polluted to different extents. The main pollutants present in drinking water sources are organic substances, ammonia nitrogen, phenols, pesticides and pathogenic micro-organisms, some of which cannot be removed effectively by the traditional water treatment processes like coagulation, sedimentation, filtration and chlorination, and the product water usually does not meet Chinese national drinking water standards, when polluted source water is treated. In some drinking-water plants in China, advanced treatment processes including activated carbon filtration and adsorption, ozonation, biological activated carbon and membrane separation have been employed for further treatment of the filtrate from a traditional treatment system producing unqualified drinking water, to make final product water meet the WHO guidelines and some developed countries' standards, as well as the Chinese national standards for drinking water. Some case studies of advanced water treatment plants are described in this paper as well.

Environmental Assessment for Clear AFS Grid Tie-in and Heat Plant, Clear Air Force Station, Alaska

DTIC Science & Technology

2013-07-01

greenhouse gases are presented in this section. 3.3.2.1 Air Quality Standards All stationary and mobile sources of air pollutants within a...These inventories provide estimates of criteria pollutant emissions associated with industrial sources, residential wood burning, mobile sources...larger, more mobile wildlife species are expected to vacate the project area, whereas individuals of less mobile species (i.e., small mammals,) could

EPA Office of Water (OW): Nonpoint Source Projects NHDPlus Indexed Dataset

EPA Pesticide Factsheets

GRTS locational data for nonpoint source projects. GRTS locations are coded onto NHDPlus v2.1 flowline features to create point and line events or coded onto NHDPlus v2.1 waterbody features to create area events. In addition to NHDPlus reach indexed data there may also be custom events (point, line or area) that are not associated with NHD and are in an EPA standard format that is compatible with EPA's Reach Address Database. Custom events are used to represent GRTS locations that are not represented well in NHDPlus.

40 CFR 63.9495 - When do I have to comply with this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Friction Materials Manufacturing... initial startup. (c) If your friction materials manufacturing facility is an area source that increases...

40 CFR 63.9495 - When do I have to comply with this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Friction Materials Manufacturing... initial startup. (c) If your friction materials manufacturing facility is an area source that increases...

40 CFR 63.9495 - When do I have to comply with this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Friction Materials Manufacturing... initial startup. (c) If your friction materials manufacturing facility is an area source that increases...

40 CFR 63.9495 - When do I have to comply with this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Friction Materials Manufacturing... initial startup. (c) If your friction materials manufacturing facility is an area source that increases...

40 CFR 63.10382 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hospital Ethylene Oxide Sterilizers Applicability and Compliance Dates § 63... ethylene oxide sterilization facility at a hospital that is an area source of hazardous air pollutant (HAP...

Standardized data sharing in a paediatric oncology research network--a proof-of-concept study.

PubMed

Hochedlinger, Nina; Nitzlnader, Michael; Falgenhauer, Markus; Welte, Stefan; Hayn, Dieter; Koumakis, Lefteris; Potamias, George; Tsiknakis, Manolis; Saraceno, Davide; Rinaldi, Eugenia; Ladenstein, Ruth; Schreier, Günter

2015-01-01

Data that has been collected in the course of clinical trials are potentially valuable for additional scientific research questions in so called secondary use scenarios. This is of particular importance in rare disease areas like paediatric oncology. If data from several research projects need to be connected, so called Core Datasets can be used to define which information needs to be extracted from every involved source system. In this work, the utility of the Clinical Data Interchange Standards Consortium (CDISC) Operational Data Model (ODM) as a format for Core Datasets was evaluated and a web tool was developed which received Source ODM XML files and--via Extensible Stylesheet Language Transformation (XSLT)--generated standardized Core Dataset ODM XML files. Using this tool, data from different source systems were extracted and pooled for joined analysis in a proof-of-concept study, facilitating both, basic syntactic and semantic interoperability.

The National Map seamless digital elevation model specifications

USGS Publications Warehouse

Archuleta, Christy-Ann M.; Constance, Eric W.; Arundel, Samantha T.; Lowe, Amanda J.; Mantey, Kimberly S.; Phillips, Lori A.

2017-08-02

This specification documents the requirements and standards used to produce the seamless elevation layers for The National Map of the United States. Seamless elevation data are available for the conterminous United States, Hawaii, Alaska, and the U.S. territories, in three different resolutions—1/3-arc-second, 1-arc-second, and 2-arc-second. These specifications include requirements and standards information about source data requirements, spatial reference system, distribution tiling schemes, horizontal resolution, vertical accuracy, digital elevation model surface treatment, georeferencing, data source and tile dates, distribution and supporting file formats, void areas, metadata, spatial metadata, and quality assurance and control.

Task Analysis for Health Occupations. Cluster: Nursing. Occupation: Professional Nurse (Associate Degree). Education for Employment Task Lists.

ERIC Educational Resources Information Center

Lake County Area Vocational Center, Grayslake, IL.

This document contains a task analysis for health occupations (professional nurse) in the nursing cluster. For each task listed, occupation, duty area, performance standard, steps, knowledge, attitudes, safety, equipment/supplies, source of analysis, and Illinois state goals for learning are listed. For the duty area of "providing therapeutic…

Task Analysis for Health Occupations. Cluster: Nursing. Occupation: Home Health Aide. Education for Employment Task Lists.

ERIC Educational Resources Information Center

Lake County Area Vocational Center, Grayslake, IL.

This document contains a task analysis for health occupations (home health aid) in the nursing cluster. For each task listed, occupation, duty area, performance standard, steps, knowledge, attitudes, safety, equipment/supplies, source of analysis, and Illinois state goals for learning are listed. For the duty area of "providing therapeutic…

77 FR 34810 - Determination of Failure To Attain by 2005 and Determination of Current Attainment of the 1-Hour...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-12

... obviates the need for submission of any contingency measures for failure to attain that revoked standard... Baltimore area is no longer obliged to submit and implement the 1-hour ozone contingency measure requirement... 1-hour nonattainment area contingency measures or major source penalty fee programs among the...

Evaluation of the APEX model to simulate runoff quality from agricultural fields in the southern region of the US

USDA-ARS?s Scientific Manuscript database

The phosphorus (P) Index (PI) is the risk assessment tool approved in the NRCS 590 standard used to target critical source areas and practices to reduce P losses. A revision of the 590 standard, suggested using the Agricultural Policy/Environmental eXtender (APEX) model to assess the risk of nitroge...

40 CFR 63.11601 - What are the standards for new and existing paints and allied products manufacturing facilities?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Hazardous Air Pollutants for Area Sources: Paints and Allied Products Manufacturing Standards, Monitoring... cleaning must be kept in a closed container. The closed container may contain a device that allows pressure relief, but does not allow liquid solvent to drain from the container. [74 FR 63525, Dec. 3, 2009, as...

40 CFR 63.11601 - What are the standards for new and existing paints and allied products manufacturing facilities?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Hazardous Air Pollutants for Area Sources: Paints and Allied Products Manufacturing Standards, Monitoring... cleaning must be kept in a closed container. The closed container may contain a device that allows pressure relief, but does not allow liquid solvent to drain from the container. [74 FR 63525, Dec. 3, 2009, as...

40 CFR 63.11601 - What are the standards for new and existing paints and allied products manufacturing facilities?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Hazardous Air Pollutants for Area Sources: Paints and Allied Products Manufacturing Standards, Monitoring... cleaning must be kept in a closed container. The closed container may contain a device that allows pressure relief, but does not allow liquid solvent to drain from the container. [74 FR 63525, Dec. 3, 2009, as...

Precision blackbody sources for radiometric standards.

PubMed

Sapritsky, V I; Khlevnoy, B B; Khromchenko, V B; Lisiansky, B E; Mekhontsev, S N; Melenevsky, U A; Morozova, S P; Prokhorov, A V; Samoilov, L N; Shapoval, V I; Sudarev, K A; Zelener, M F

1997-08-01

The precision blackbody sources developed at the All-Russian Institute for Optical and Physical Measurements (Moscow, Russia) and their characteristics are analyzed. The precision high-temperature graphite blackbody BB22p, large-area high-temperature pyrolytic graphite blackbody BB3200pg, middle-temperature graphite blackbody BB2000, low-temperature blackbody BB300, and gallium fixed-point blackbody BB29gl and their characteristics are described.

[The assessment of the quality of water from sources of decentralized water supply of Ekaterinburg and surrounding areas].

PubMed

Konshina, Lidia G

2016-01-01

The availability of high-quality drinking water is currently the one out of the most acute problems in the Russian Federation. There was performed an analysis of the chemical composition of drinking water from sources of decentralized supply of inhabitants of the city of Yekaterinburg and the surrounding areas. Average values of indices of the water quality in the wells for individual use in the district of the city of Yekaterinburg not go beyond the standards, with the exception of manganese content. In some sources there were revealed elevated values of chromatic level, oxidability, hardness, content of iron, nitrates, barium, dry residue, ammonium nitrogen, silicon. Percentage of sources that do not meet hygienic requirements on a number of indices can reach 21-23%.

40 CFR Table 2 to Subpart Jjjjjj... - Work Practice Standards, Emission Reduction Measures, and Management Practices

Code of Federal Regulations, 2012 CFR

2012-07-01

... Hazardous Air Pollutants for Industrial, Commercial, and Institutional Boilers Area Sources Pt. 63, Subpt... of available architectural and engineering plans, facility operation and maintenance procedures and...

40 CFR Table 2 to Subpart Jjjjjj... - Work Practice Standards, Emission Reduction Measures, and Management Practices

Code of Federal Regulations, 2011 CFR

2011-07-01

... Hazardous Air Pollutants for Industrial, Commercial, and Institutional Boilers Area Sources Pt. 63, Subpt... of available architectural and engineering plans, facility operation and maintenance procedures and...

77 FR 4522 - National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-30

... Manufacturing, Industrial Organic Chemical Manufacturing, Inorganic Pigments Manufacturing, Miscellaneous Organic Chemical Manufacturing, Plastic Materials and Resins Manufacturing, Pharmaceutical Production and... Intermediate Production, Industrial Inorganic Chemical Manufacturing, Industrial Organic Chemical Manufacturing...

40 CFR 52.27 - Protection of visibility from sources in attainment areas.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quality standards for such pollutants, and where a State PSD program has been approved as part of the... Act, in the prevention of significant deterioration (PSD) program approved as part of the applicable...

40 CFR 52.27 - Protection of visibility from sources in attainment areas.

Code of Federal Regulations, 2011 CFR

2011-07-01

... quality standards for such pollutants, and where a State PSD program has been approved as part of the... Act, in the prevention of significant deterioration (PSD) program approved as part of the applicable...

40 CFR 52.27 - Protection of visibility from sources in attainment areas.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quality standards for such pollutants, and where a State PSD program has been approved as part of the... Act, in the prevention of significant deterioration (PSD) program approved as part of the applicable...

40 CFR 52.27 - Protection of visibility from sources in attainment areas.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quality standards for such pollutants, and where a State PSD program has been approved as part of the... Act, in the prevention of significant deterioration (PSD) program approved as part of the applicable...

40 CFR 52.27 - Protection of visibility from sources in attainment areas.

Code of Federal Regulations, 2010 CFR

2010-07-01

... quality standards for such pollutants, and where a State PSD program has been approved as part of the... Act, in the prevention of significant deterioration (PSD) program approved as part of the applicable...

Review of Selected References and Data sets on Ambient Ground- and Surface-Water Quality in the Metedeconk River, Toms River, and Kettle Creek Basins, New Jersey, 1980-2001

USGS Publications Warehouse

Nicholson, Robert S.; Hunchak-Kariouk, Kathryn; Cauller, Stephen J.

2003-01-01

Surface water and ground water from unconfined aquifers are the primary sources of drinking water for much of the population, about 391,000, in the Metedeconk River, Toms River, and Kettle Creek watersheds in the New Jersey Coastal Plain. The quality of these sources of drinking water is a concern because they are vulnerable to contamination. Indications of the occurrence, distribution, and likely sources and transport mechanisms of certain contaminants were obtained from 48 selected reports and 2 selected data sets on water quality in or near the watersheds (1980-2001). These indications are described and briefly summarized in this report. The findings of studies on ground-water quality indicate that shallow ground water within the study area generally meets primary drinking-water standards, with notable exceptions. Volatile organic compounds, mercury, arsenic, radionuclides, nitrate, and coliform bacteria have been detected in shallow ground water in some areas at levels that exceed Federal and State drinking-water standards. For example, results of analyses of untreated samples collected from more than 13,000 private wells during 1983-99 indicated that concentrations of volatile organic compounds in samples from 7.3 percent of the wells exceeded at least 1 of 11 drinking-water standards, according to records maintained by the Ocean County Health Department. In cases of exceedances, however, water treatment, well replacement, and (or) retesting assured that applicable drinking-water standards were being met at the tap. Reported concentrations of the pesticide chlordane in some areas exceeded the drinking-water standard; few data are available on the occurrence of other pesticides. Studies of nearby areas, however, indicate that pesticide concentrations generally could be expected to be below drinking-water standards. The combination of low pH and low dissolved solids in many areas results in shallow ground water that is highly corrosive and, if untreated, able to leach trace elements and release asbestos fibers from plumbing materials. Reported concentrations of nitrate, volatile organic compounds, trace elements, and pesticides in samples from the monitored mainstem and tributary streams within the study area generally are below maximum contaminant levels for drinking water or below detection limits. Results of studies in other areas indicate that pesticide concentrations in surface water could be considerably higher during high flows soon after the application of pesticides to crops than during low flows. Fecal coliform bacteria counts in streams vary considerably. Concentrations or counts of these classes of surface-water-quality constituents likely are functions of the intensity and type of upstream development. Results of limited monitoring for radionuclide concentrations reported by the Brick Township Municipal Utilities Authority of the Metedeconk River indicate that radionuclide concentrations or activities do not exceed maximum contaminant levels for drinking water. As a consequence of organic matter in surface water, the formati ultraviolet absorbance in samples from the Metedeconk River and the Toms River exceeded the alternative compliance criteria for source water (2.0 milligrams per liter for total organic carbon and 0.02 absorbance units-liters per milligram-centimeter for specific ultraviolet absorbance) with respect to treatment requirements for preventing elevated concentrations of disinfection by-products in treated water. Water-quality and treatment issues associated with use of ground and surface water for potable supply in the study area are related to human activities and naturally occurring factors. Additional monitoring and analysis of ground and surface water would be needed to determine conclusively the occurrence and distribution of some contaminants and the relative importance of various potential contaminant sources, transport and attenuation mechanisms, and transport pathways.

Source apportionment of emissions from light-duty gasoline vehicles and other sources in the United States for ozone and particulate matter.

PubMed

Vijayaraghavan, Krish; Lindhjem, Chris; Koo, Bonyoung; DenBleyker, Allison; Tai, Edward; Shah, Tejas; Alvarez, Yesica; Yarwood, Greg

2016-02-01

Federal Tier 3 motor vehicle emission and fuel sulfur standards have been promulgated in the United States to help attain air quality standards for ozone and PM2.5 (particulate matter with an aerodynamic diameter <2.5 μm). The authors modeled a standard similar to Tier 3 (a hypothetical nationwide implementation of the California Low Emission Vehicle [LEV] III standards) and prior Tier 2 standards for on-road gasoline-fueled light-duty vehicles (gLDVs) to assess incremental air quality benefits in the United States (U.S.) and the relative contributions of gLDVs and other major source categories to ozone and PM2.5 in 2030. Strengthening Tier 2 to a Tier 3-like (LEV III) standard reduces the summertime monthly mean of daily maximum 8-hr average (MDA8) ozone in the eastern U.S. by up to 1.5 ppb (or 2%) and the maximum MDA8 ozone by up to 3.4 ppb (or 3%). Reducing gasoline sulfur content from 30 to 10 ppm is responsible for up to 0.3 ppb of the improvement in the monthly mean ozone and up to 0.8 ppb of the improvement in maximum ozone. Across four major urban areas-Atlanta, Detroit, Philadelphia, and St. Louis-gLDV contributions range from 5% to 9% and 3% to 6% of the summertime mean MDA8 ozone under Tier 2 and Tier 3, respectively, and from 7% to 11% and 3% to 7% of the maximum MDA8 ozone under Tier 2 and Tier 3, respectively. Monthly mean 24-hr PM2.5 decreases by up to 0.5 μg/m(3) (or 3%) in the eastern U.S. from Tier 2 to Tier 3, with about 0.1 μg/m(3) of the reduction due to the lower gasoline sulfur content. At the four urban areas under the Tier 3 program, gLDV emissions contribute 3.4-5.0% and 1.7-2.4% of the winter and summer mean 24-hr PM2.5, respectively, and 3.8-4.6% and 1.5-2.0% of the mean 24-hr PM2.5 on days with elevated PM2.5 in winter and summer, respectively. Following U.S. Tier 3 emissions and fuel sulfur standards for gasoline-fueled passenger cars and light trucks, these vehicles are expected to contribute less than 6% of the summertime mean daily maximum 8-hr ozone and less than 7% and 4% of the winter and summer mean 24-hr PM2.5 in the eastern U.S. in 2030. On days with elevated ozone or PM2.5 at four major urban areas, these vehicles contribute less than 7% of ozone and less than 5% of PM2.5, with sources outside North America and U.S. area source emissions constituting some of the main contributors to ozone and PM2.5, respectively.

Flushing of distal hillslopes as an alternative source of stream dissolved organic carbon in a headwater catchment

USGS Publications Warehouse

Gannon, John P; Bailey, Scott W.; McGuire, Kevin J.; Shanley, James B.

2015-01-01

We investigated potential source areas of dissolved organic carbon (DOC) in headwater streams by examining DOC concentrations in lysimeter, shallow well, and stream water samples from a reference catchment at the Hubbard Brook Experimental Forest. These observations were then compared to high-frequency temporal variations in fluorescent dissolved organic matter (FDOM) at the catchment outlet and the predicted spatial extent of shallow groundwater in soils throughout the catchment. While near-stream soils are generally considered a DOC source in forested catchments, DOC concentrations in near-stream groundwater were low (mean = 2.4 mg/L, standard error = 0.6 mg/L), less than hillslope groundwater farther from the channel (mean = 5.7 mg/L, standard error = 0.4 mg/L). Furthermore, water tables in near-stream soils did not rise into the carbon-rich upper B or O horizons even during events. In contrast, soils below bedrock outcrops near channel heads where lateral soil formation processes dominate had much higher DOC concentrations. Soils immediately downslope of bedrock areas had thick eluvial horizons indicative of leaching of organic materials, Fe, and Al and had similarly high DOC concentrations in groundwater (mean = 14.5 mg/L, standard error = 0.8 mg/L). Flow from bedrock outcrops partially covered by organic soil horizons produced the highest groundwater DOC concentrations (mean = 20.0 mg/L, standard error = 4.6 mg/L) measured in the catchment. Correspondingly, stream water in channel heads sourced in part by shallow soils and bedrock outcrops had the highest stream DOC concentrations measured in the catchment. Variation in FDOM concentrations at the catchment outlet followed water table fluctuations in shallow to bedrock soils near channel heads. We show that shallow hillslope soils receiving runoff from organic matter-covered bedrock outcrops may be a major source of DOC in headwater catchments in forested mountainous regions where catchments have exposed or shallow bedrock near channel heads.

River water quality and pollution sources in the Pearl River Delta, China.

PubMed

Ouyang, Tingping; Zhu, Zhaoyu; Kuang, Yaoqiu

2005-07-01

Some physicochemical parameters were determined for thirty field water samples collected from different water channels in the Pearl River Delta Economic Zone river system. The analytical results were compared with the environmental quality standards for surface water. Using the SPSS software, statistical analyses were performed to determine the main pollutants of the river water. The main purpose of the present research is to investigate the river water quality and to determine the main pollutants and pollution sources. Furthermore, the research provides some approaches for protecting and improving river water quality. The results indicate that the predominant pollutants are ammonium, phosphorus, and organic compounds. The wastewater discharged from households in urban and rural areas, industrial facilities, and non-point sources from agricultural areas are the main sources of pollution in river water in the Pearl River Delta Economic Zone.

Another Look at the Great Area-Coverage Controversy of the 1950's

NASA Astrophysics Data System (ADS)

Blanchard, Walter

2005-09-01

In the immediate aftermath of WW2 there sprang up an international argument over the relative merits for aerial navigation of area-coverage radio navaids versus point-source systems. The United States was in favour of point-source whereas the UK proposed area-coverage, systems for which had successfully been demonstrated under very adverse conditions during the war. It rumbled on for many years, not being finally settled until the ICAO Montreal Conference of 1959 decided for point-source. Since then, VOR/DME/ADF/ILS have been the standard aviation radio navaids and there seems little likelihood of any change in the near future, GNSS notwithstanding, if one discounts the phasing-out of ADF. It now seems sufficiently in the past to perhaps allow a dispassionate evaluation of the technical arguments used at the time the political ones can be left to another place and time.

Petition for EPA action to protect communities from oil and gas wells toxic air pollution

EPA Pesticide Factsheets

Petition submitted by Earthjustice urging EPA to list oil and gas wells and associated equipment as an area sourcecategory and set national air toxics standards to protect public health from these sources.

Acrylic and Modacrylic Fibers Production: National Emission Standards for Hazardous Air Pollutants (NESHAP) for Area Sources

EPA Pesticide Factsheets

This NESHAP applies to facilities using pressure or thermal treatment processes involving wood preservatives containing chromium, arsenic, dioxins, or methylene chloride. Page includes rule summary, rule history and additional documents.

Flexible Polyurethane Foam Production and Fabrication: National Emission Standards for Hazardous Air Pollutants (NESHAP) for Area Sources

EPA Pesticide Factsheets

This NESHAP applies to facilities using pressure or thermal treatment processes involving wood preservatives containing chromium, arsenic, dioxins, or methylene chloride. Inlcudes federal register citations, rule history and additional resources.

Background derivation and image flattening: getimages

NASA Astrophysics Data System (ADS)

Men'shchikov, A.

2017-11-01

Modern high-resolution images obtained with space observatories display extremely strong intensity variations across images on all spatial scales. Source extraction in such images with methods based on global thresholding may bring unacceptably large numbers of spurious sources in bright areas while failing to detect sources in low-background or low-noise areas. It would be highly beneficial to subtract background and equalize the levels of small-scale fluctuations in the images before extracting sources or filaments. This paper describes getimages, a new method of background derivation and image flattening. It is based on median filtering with sliding windows that correspond to a range of spatial scales from the observational beam size up to a maximum structure width Xλ. The latter is a single free parameter of getimages that can be evaluated manually from the observed image ℐλ. The median filtering algorithm provides a background image \\tilde{Bλ} for structures of all widths below Xλ. The same median filtering procedure applied to an image of standard deviations 𝓓λ derived from a background-subtracted image \\tilde{Sλ} results in a flattening image \\tilde{Fλ}. Finally, a flattened detection image I{λD} = \\tilde{Sλ}/\\tilde{Fλ} is computed, whose standard deviations are uniform outside sources and filaments. Detecting sources in such greatly simplified images results in much cleaner extractions that are more complete and reliable. As a bonus, getimages reduces various observational and map-making artifacts and equalizes noise levels between independent tiles of mosaicked images.

Open source tools and toolkits for bioinformatics: significance, and where are we?

PubMed

Stajich, Jason E; Lapp, Hilmar

2006-09-01

This review summarizes important work in open-source bioinformatics software that has occurred over the past couple of years. The survey is intended to illustrate how programs and toolkits whose source code has been developed or released under an Open Source license have changed informatics-heavy areas of life science research. Rather than creating a comprehensive list of all tools developed over the last 2-3 years, we use a few selected projects encompassing toolkit libraries, analysis tools, data analysis environments and interoperability standards to show how freely available and modifiable open-source software can serve as the foundation for building important applications, analysis workflows and resources.

40 CFR 63.11459 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... or more furnaces that are identical in design, including manufacturer, dimensions, production... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area Sources.... Continuous furnace means a glass manufacturing furnace that operates continuously except during periods of...

Paints and Allied Products Manufacturing: National Emission Standards for Hazardous Air Pollutants (NESHAP) for Area Sources

EPA Pesticide Factsheets

Read the text of this NESHAP regulation on Paints and Allied Products manufacturing. Find the rule summary, and rule history, effective dates, and the federal register citations and fact sheets on the rule.

A Parallel, High-Fidelity Radar Model

DTIC Science & Technology

2010-09-01

THIS PAGE unclassified Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 . TCMB is the temperature due to the cosmic microwave background ...per unit area, per unit frequency. In the microwave regime, this is usually given the name brightness temperature, . There are various sources...which contribute to the brightness temperature. They include external sources outside of the earth’s atmosphere (e.g. cosmic or galactic noise

Air quality status of an open pit mining area in India.

PubMed

Chaulya, S K

2005-06-01

This investigation presents the assessment of ambient air quality carried out at an open pit coal mining area in Orissa state of India. The 24-h average concentrations of suspended particulate matter (SPM), respirable particulate matter (RPM, particles of less than 10 microm aerodynamic diameter), sulphur dioxide (SO2) and oxides of nitrogen (NO(x)) were determined at regular interval throughout one year at 13 monitoring stations in residential area and four stations in mining/industrial area. During the study period, the 24-h and annual average SPM and RPM concentrations exceeded the respective standards set in the Indian ambient air quality standard (NAAQS) protocol in most of the residential and industrial areas. However, the 24-h and annual average concentrations of SO2 and NO(x) were well within the prescribed limit of the NAAQS in both residential and industrial areas. A management strategy is formulated for effective control of particulate matter at source and other mitigative measures are recommended including implementation of green belts around the sensitive areas.

Rural:urban inequalities in post 2015 targets and indicators for drinking-water.

PubMed

Bain, R E S; Wright, J A; Christenson, E; Bartram, J K

2014-08-15

Disparities in access to drinking water between rural and urban areas are pronounced. Although use of improved sources has increased more rapidly in rural areas, rising from 62% in 1990 to 81% in 2011, the proportion of the rural population using an improved water source remains substantially lower than in urban areas. Inequalities in coverage are compounded by disparities in other aspects of water service. Not all improved sources are safe and evidence from a systematic review demonstrates that water is more likely to contain detectable fecal indicator bacteria in rural areas. Piped water on premises is a service enjoyed primarily by those living in urban areas so differentiating amongst improved sources would exacerbate rural:urban disparities yet further. We argue that an urban bias may have resulted due to apparent stagnation in urban coverage and the inequity observed between urban and peri-urban areas. The apparent stagnation at around 95% coverage in urban areas stems in part from relative population growth - over the last two decades more people gained access to improved water in urban areas. There are calls for setting higher standards in urban areas which would exacerbate the already extreme rural disadvantage. Instead of setting different targets, health, economic, and human rights perspectives, We suggest that the focus should be kept on achieving universal access to safe water (primarily in rural areas) while monitoring progress towards higher service levels, including greater water safety (both in rural and urban areas and among different economic strata). Copyright © 2014 Elsevier B.V. All rights reserved.

Null-space Monte Carlo particle tracking to assess groundwater PCE (Tetrachloroethene) diffuse pollution in north-eastern Milan functional urban area.

PubMed

Alberti, Luca; Colombo, Loris; Formentin, Giovanni

2018-04-15

The Lombardy Region in Italy is one of the most urbanized and industrialized areas in Europe. The presence of countless sources of groundwater pollution is therefore a matter of environmental concern. The sources of groundwater contamination can be classified into two different categories: 1) Point Sources (PS), which correspond to areas releasing plumes of high concentrations (i.e. hot-spots) and 2) Multiple-Point Sources (MPS) consisting in a series of unidentifiable small sources clustered within large areas, generating an anthropogenic diffuse contamination. The latter category frequently predominates in European Functional Urban Areas (FUA) and cannot be managed through standard remediation techniques, mainly because detecting the many different source areas releasing small contaminant mass in groundwater is unfeasible. A specific legislative action has been recently enacted at Regional level (DGR IX/3510-2012), in order to identify areas prone to anthropogenic diffuse pollution and their level of contamination. With a view to defining a management plan, it is necessary to find where MPS are most likely positioned. This paper describes a methodology devised to identify the areas with the highest likelihood to host potential MPS. A groundwater flow model was implemented for a pilot area located in the Milan FUA and through the PEST code, a Null-Space Monte Carlo method was applied in order to generate a suite of several hundred hydraulic conductivity field realizations, each maintaining the model in a calibrated state and each consistent with the modelers' expert-knowledge. Thereafter, the MODPATH code was applied to generate back-traced advective flowpaths for each of the models built using the conductivity field realizations. Maps were then created displaying the number of backtracked particles that crossed each model cell in each stochastic calibrated model. The result is considered to be representative of the FUAs areas with the highest likelihood to host MPS responsible for diffuse contamination. Copyright © 2017 Elsevier B.V. All rights reserved.

FreeSASA: An open source C library for solvent accessible surface area calculations.

PubMed

Mitternacht, Simon

2016-01-01

Calculating solvent accessible surface areas (SASA) is a run-of-the-mill calculation in structural biology. Although there are many programs available for this calculation, there are no free-standing, open-source tools designed for easy tool-chain integration. FreeSASA is an open source C library for SASA calculations that provides both command-line and Python interfaces in addition to its C API. The library implements both Lee and Richards' and Shrake and Rupley's approximations, and is highly configurable to allow the user to control molecular parameters, accuracy and output granularity. It only depends on standard C libraries and should therefore be easy to compile and install on any platform. The library is well-documented, stable and efficient. The command-line interface can easily replace closed source legacy programs, with comparable or better accuracy and speed, and with some added functionality.

Applicability of source scaling relations for crustal earthquakes to estimation of the ground motions of the 2016 Kumamoto earthquake

NASA Astrophysics Data System (ADS)

Irikura, Kojiro; Miyakoshi, Ken; Kamae, Katsuhiro; Yoshida, Kunikazu; Somei, Kazuhiro; Kurahashi, Susumu; Miyake, Hiroe

2017-01-01

A two-stage scaling relationship of the source parameters for crustal earthquakes in Japan has previously been constructed, in which source parameters obtained from the results of waveform inversion of strong motion data are combined with parameters estimated based on geological and geomorphological surveys. A three-stage scaling relationship was subsequently developed to extend scaling to crustal earthquakes with magnitudes greater than M w 7.4. The effectiveness of these scaling relationships was then examined based on the results of waveform inversion of 18 recent crustal earthquakes ( M w 5.4-6.9) that occurred in Japan since the 1995 Hyogo-ken Nanbu earthquake. The 2016 Kumamoto earthquake, with M w 7.0, was one of the largest earthquakes to occur since dense and accurate strong motion observation networks, such as K-NET and KiK-net, were deployed after the 1995 Hyogo-ken Nanbu earthquake. We examined the applicability of the scaling relationships of the source parameters of crustal earthquakes in Japan to the 2016 Kumamoto earthquake. The rupture area and asperity area were determined based on slip distributions obtained from waveform inversion of the 2016 Kumamoto earthquake observations. We found that the relationship between the rupture area and the seismic moment for the 2016 Kumamoto earthquake follows the second-stage scaling within one standard deviation ( σ = 0.14). The ratio of the asperity area to the rupture area for the 2016 Kumamoto earthquake is nearly the same as ratios previously obtained for crustal earthquakes. Furthermore, we simulated the ground motions of this earthquake using a characterized source model consisting of strong motion generation areas (SMGAs) based on the empirical Green's function (EGF) method. The locations and areas of the SMGAs were determined through comparison between the synthetic ground motions and observed motions. The sizes of the SMGAs were nearly coincident with the asperities with large slip. The synthetic ground motions obtained using the EGF method agree well with the observed motions in terms of acceleration, velocity, and displacement within the frequency range of 0.3-10 Hz. These findings indicate that the 2016 Kumamoto earthquake is a standard event that follows the scaling relationship of crustal earthquakes in Japan.

40 CFR 63.51 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES Requirements for Control Technology..., activities, or both within a single contiguous area and under common control that is in a section 112(c... finding and identifying control technology options under this subpart, any information that is available...

40 CFR 63.51 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES Requirements for Control Technology..., activities, or both within a single contiguous area and under common control that is in a section 112(c... finding and identifying control technology options under this subpart, any information that is available...

40 CFR 63.51 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES Requirements for Control Technology..., activities, or both within a single contiguous area and under common control that is in a section 112(c... finding and identifying control technology options under this subpart, any information that is available...

40 CFR 63.51 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES Requirements for Control Technology..., activities, or both within a single contiguous area and under common control that is in a section 112(c... finding and identifying control technology options under this subpart, any information that is available...

40 CFR 63.51 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES Requirements for Control Technology..., activities, or both within a single contiguous area and under common control that is in a section 112(c... finding and identifying control technology options under this subpart, any information that is available...

Very Long Baseline Interferometry: Dependencies on Frequency Stability

NASA Astrophysics Data System (ADS)

Nothnagel, Axel; Nilsson, Tobias; Schuh, Harald

2018-04-01

Very Long Baseline Interferometry (VLBI) is a differential technique observing radiation of compact extra-galactic radio sources with pairs of radio telescopes. For these observations, the frequency standards at the telescopes need to have very high stability. In this article we discuss why this is, and we investigate exactly how precise the frequency standards need to be. Four areas where good clock performance is needed are considered: coherence, geodetic parameter estimation, correlator synchronization, and UT1 determination. We show that in order to ensure the highest accuracy of VLBI, stability similar to that of a hydrogen maser is needed for time-scales up to a few hours. In the article, we are considering both traditional VLBI where extra-galactic radio sources are observed, as well as observation of man-made artificial radio sources emitted by satellites or spacecrafts.

77 FR 28423 - Final Rule To Implement the 1997 8-Hour Ozone National Ambient Air Quality Standard...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-14

...The EPA is revising the rules for implementing the 1997 8-hour ozone national ambient air quality standards (NAAQS) to address certain limited portions of the rules vacated by the U.S. Court of Appeals for the District of Columbia Circuit. This final rule assigns Clean Air Act (CAA or Act) classifications and associated state planning and control requirements to selected ozone nonattainment areas. This final rule also addresses three vacated provisions of the 1997 8-hour NAAQS--Phase 1 Implementation Rule (April 30, 2004) that provided exemptions from the anti-backsliding requirements relating to nonattainment area New Source Review (NSR), CAA section 185 penalty fees, and contingency measures, as these three requirements applied for the 1-hour standard. This rule also reinstates the 1-hour contingency measures as applicable requirements that must be retained until the area attains the 1997 8- hour ozone standard. Finally, this rule deletes an obsolete provision that stayed the EPA's authority to revoke the 1-hour ozone standard pending the Agency's issuance of a final rule that revises or reinstates its revocation authority and considers and addresses certain other issues. That rule has now been issued.

Retrofitting impervious urban infrastructure with green technology for rainfall-runoff restoration, indirect reuse and pollution load reduction.

PubMed

Sansalone, John; Raje, Saurabh; Kertesz, Ruben; Maccarone, Kerrilynn; Seltzer, Karl; Siminari, Michele; Simms, Peter; Wood, Brandon

2013-12-01

The built environs alter hydrology and water resource chemistry. Florida is subject to nutrient criteria and is promulgating "no-net-load-increase" criteria for runoff and constituents (nutrients and particulate matter, PM). With such criteria, green infrastructure, hydrologic restoration, indirect reuse and source control are potential design solutions. The study simulates runoff and constituent load control through urban source area re-design to provide long-term "no-net-load-increases". A long-term continuous simulation of pre- and post-development response for an existing surface parking facility is quantified. Retrofits include a biofiltration area reactor (BAR) for hydrologic and denitrification control. A linear infiltration reactor (LIR) of cementitious permeable pavement (CPP) provides infiltration, adsorption and filtration. Pavement cleaning provided source control. Simulation of climate and source area data indicates re-design achieves "no-net-load-increases" at lower costs compared to standard construction. The retrofit system yields lower cost per nutrient load treated compared to Best Management Practices (BMPs). Copyright © 2013 Elsevier Ltd. All rights reserved.

Initial turnover rates of two standard wood substrates following land-use change in subalpine ecosystems in the Swiss Alps

Treesearch

Anita C. Risch; Martin F. Jurgensen; Deborah S. Page-Dumroese; Martin Schutz

2013-01-01

Forest cover has increased in mountainous areas of Europe over the past decades because of the abandonment of agricultural areas (land-use change). For this reason, understanding how land-use change affects carbon (C) source-sink strength is of great importance. However, most studies have assessed mountainous systems C stocks, and less is known about C turnover rates,...

Bacterial indicator occurrence and the use of an F+ specific RNA coliphage assay to identify fecal sources in Homosassa Springs, Florida

USGS Publications Warehouse

Griffin, Dale W.; Stokes, Rodger; Rose, J.B.; Paul, J.H.

2000-01-01

A microbiological water quality study of Homosassa Springs State Wildlife Park (HSSWP) and surrounding areas was undertaken. Samples were collected in November of 1997 (seven sites) and again in November of 1998 (nine sites). Fecal bacterial concentrations (total and fecal coliforms, Clostridium perfringens, and enterococci) were measured as relative indicators of fecal contamination. F+-specific coliphage genotyping was performed to determine the source of fecal contamination at the study sites. Bacterial levels were considerably higher at most sites in the 1997 sampling compared to the 1998 sampling, probably because of the greater rainfall that year. In November of 1997, 2 of the 7 sites were in violation of all indicator standards and guidance levels. In November of 1998, 1 of 9 sites was in violation of all indicator standard and guidance levels. The highest concentrations of all fecal indicators were found at a station downstream of the animal holding pens in HSSWP. The lowest levels of indicators were found at the Homosassa Main Spring vent. Levels of fecal indicators downstream of HSSWP (near the point of confluence with the river) were equivalent to those found in the Southeastern Fork and areas upstream of the park influences. F+ specific RNA coliphage analysis indicated that fecal contamination at all sites that tested positive was from animal sources (mammals and birds). These results suggest that animal (indigenous and those in HSSWP) and not human sources influenced microbial water quality in the area of Homosassa River covered by this study.

Trends in atmospheric particulate matter in Dhaka, Bangladesh, and the vicinity.

PubMed

Rana, Md Masud; Sulaiman, Norela; Sivertsen, Bjarne; Khan, Md Firoz; Nasreen, Sabera

2016-09-01

Dhaka and its neighboring areas suffer from severe air pollution, especially during dry season (November-April). We investigated temporal and directional variations in particulate matter (PM) concentrations in Dhaka, Gazipur, and Narayanganj from October 2012 to March 2015 to understand different aspects of PM concentrations and possible sources of high pollution in this region. Ninety-six-hour backward trajectories for the whole dry season were also computed to investigate incursion of long-range pollution into this area. We found yearly PM10 concentrations in this area about three times and yearly PM2.5 concentrations about six times greater than the national standards of Bangladesh. Dhaka and its vicinity experienced several air pollution episodes in dry season when PM2.5 concentrations were 8-13 times greater than the World Health Organization (WHO) guideline value. Higher pollution and great contribution of PM2.5 most of the time were associated with the north-westerly wind. Winter (November to January) was found as the most polluted season in this area, when average PM10 concentrations in Dhaka, Gazipur, and Narayanganj were 257.1, 240.3, and 327.4 μg m(-3), respectively. Pollution levels during wet season (May-October) were, although found legitimate as per the national standards of Bangladesh, exceeded WHO guideline value in 50 % of the days of that season. Trans-boundary source identifications using concentration-weighted trajectory method revealed that the sources in the eastern Indian region bordering Bangladesh, in the north-eastern Indian region bordering Nepal and in Nepal and its neighboring areas had high probability of contributing to the PM pollutions at Gazipur station.

The measures for achieving nZEB standard of retrofitted educational building for specific polish location - case study

NASA Astrophysics Data System (ADS)

Kwiatkowski, Jerzy; Mijakowski, Maciej; Trząski, Adrian

2017-11-01

Most of the EU member states have already set a definition of nZEB for new buildings and some of the countries also done it for existing buildings. As there is no definition of nZEB for existing buildings in Poland, the paper will include various considerations of such a standard. Next, a case study of educational building retrofitting to a proposed nZEB standard will be presented. The aim of the paper is to present what measures can be used in order to decrease energy consumption in existing building. The measures are divided into three parts: architectural and construction, installations and energy sources. Thus a complexity of the solutions are presented. As the nZEB standard is related to available energy sources, also an influence of local condition will be considered. Building chosen for analysis is located in an area under historic protection which makes the work even more difficult. It was proved that used solutions were chosen not only to reduce energy demand or increase energy production from renewable energy sources, but also to increase social and aesthetic features of the building.

40 CFR 63.11582 - What are my compliance requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations... engineering calculations, then the calculations and supporting documentation must contain the items specified... amount of raw materials used in the manufacture of chemical preparations (as defined in § 63.11588) in...

76 FR 15553 - National Emission Standards for Hazardous Air Pollutants for Area Sources: Industrial, Commercial...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-21

... unpredictability of the non-mercury metal HAP compositions and amounts in fuel has a material effect on the... heat input. c. Carbon 400 ppm by volume on a dry basis corrected Monoxide. to 3 percent oxygen. >=10... 15560

40 CFR 63.11502 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

...: process knowledge, an engineering assessment, or test data. Byproduct means a chemical (liquid, gas, or... limit applicable to the process vent. (4) Design analysis based on accepted chemical engineering... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources...

40 CFR 63.11582 - What are my compliance requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations... engineering calculations, then the calculations and supporting documentation must contain the items specified... amount of raw materials used in the manufacture of chemical preparations (as defined in § 63.11588) in...

40 CFR 63.11502 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

...: process knowledge, an engineering assessment, or test data. Byproduct means a chemical (liquid, gas, or... limit applicable to the process vent. (4) Design analysis based on accepted chemical engineering... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources...

40 CFR 63.11582 - What are my compliance requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations... engineering calculations, then the calculations and supporting documentation must contain the items specified... amount of raw materials used in the manufacture of chemical preparations (as defined in § 63.11588) in...

40 CFR 63.11582 - What are my compliance requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations... engineering calculations, then the calculations and supporting documentation must contain the items specified... amount of raw materials used in the manufacture of chemical preparations (as defined in § 63.11588) in...

40 CFR 63.11502 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

...: process knowledge, an engineering assessment, or test data. Byproduct means a chemical (liquid, gas, or... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources...., for chemical value as a product, isolated intermediate, byproduct, or coproduct, or for heat value...

40 CFR 63.11582 - What are my compliance requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations... engineering calculations, then the calculations and supporting documentation must contain the items specified... amount of raw materials used in the manufacture of chemical preparations (as defined in § 63.11588) in...

30 CFR 77.1434 - Retirement criteria.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Personnel... corrosion; (e) Distortion of the rope structure; (f) Heat damage from any source; (g) Diameter reduction due...

40 CFR 63.11401 - What are my compliance dates?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false What are my compliance dates? 63.11401 Section 63.11401 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Hazardous Air Pollutants for Carbon Black Production Area Sources...

Assessment of well vulnerability for groundwater source protection based on a solute transport model: a case study from Jilin City, northeast China

NASA Astrophysics Data System (ADS)

Huan, Huan; Wang, Jinsheng; Lai, Desheng; Teng, Yanguo; Zhai, Yuanzheng

2015-05-01

Well vulnerability assessment is essential for groundwater source protection. A quantitative approach to assess well vulnerability in a well capture zone is presented, based on forward solute transport modeling. This method was applied to three groundwater source areas (Jiuzhan, Hadawan and Songyuanhada) in Jilin City, northeast China. The ratio of the maximum contaminant concentration at the well to the released concentration at the contamination source ( c max/ c 0) was determined as the well vulnerability indicator. The results indicated that well vulnerability was higher close to the pumping well. The well vulnerability in each groundwater source area was low. Compared with the other two source areas, the cone of depression at Jiuzhan resulted in higher spatial variability of c max/ c 0 and lower minimum c max/ c 0 by three orders of magnitude. Furthermore, a sensitivity analysis indicated that the denitrification rate in the aquifer was the most sensitive with respect to well vulnerability. A process to derive a NO3-N concentration at the pumping well is presented, based on determining the maximum nitrate loading limit to satisfy China's drinking-water quality standards. Finally, the advantages, disadvantages and prospects for improving the precision of this well vulnerability assessment approach are discussed.

Probabilistic location estimation of acoustic emission sources in isotropic plates with one sensor

NASA Astrophysics Data System (ADS)

Ebrahimkhanlou, Arvin; Salamone, Salvatore

2017-04-01

This paper presents a probabilistic acoustic emission (AE) source localization algorithm for isotropic plate structures. The proposed algorithm requires only one sensor and uniformly monitors the entire area of such plates without any blind zones. In addition, it takes a probabilistic approach and quantifies localization uncertainties. The algorithm combines a modal acoustic emission (MAE) and a reflection-based technique to obtain information pertaining to the location of AE sources. To estimate confidence contours for the location of sources, uncertainties are quantified and propagated through the two techniques. The approach was validated using standard pencil lead break (PLB) tests on an Aluminum plate. The results demonstrate that the proposed source localization algorithm successfully estimates confidence contours for the location of AE sources.

Potential sources of bacteriological pollution for two bays with marinas in Trinidad.

PubMed

Bullock, Christine Ann; Moonesar, Indar

2005-05-01

Welcome Bay and Chaguaramas Bay in the northwest peninsula of Trinidad contain large marinas and smaller sections of bathing beaches. Bacteriological surveys were conducted at both bays to assess water quality and to determine potential sources of pollution. These surveys were conducted during the wet season of 1996 and the dry season of 1997. Eleven sample stations were established at Welcome Bay and 12 at Chaguaramas Bay. Freshwater samples were collected from rivers and drains within the survey area. Marine water samples were collected from marinas, bathing beaches and inshore and outer areas at both bays. Five water samples were collected from each sampling station during the wet season of 1996 and six during the dry season of 1997. The membrane filter technique was used to determine faecal coliform and Escherichia coli levels in all samples. There was a seasonal effect on water quality, with significantly higher faecal coliform levels in the wet season, when water quality was not in compliance with international standards. This represents a potential health risk in bathing areas. Water quality was better at the outer area of both bays. Water quality at the inner bay areas was most likely adversely affected by land-based sources of pollution identified in this study. These sources include three drains and two rivers, which discharged into the bays. Yachts were apparently not a source of sewage pollution: there was no significant relationship between yacht number and faecal coliform levels.

[Cancers in children in the Auvergne area: retrospective study from 1986 to 1991].

PubMed

Gembara, P; Dechelotte, P; Chauvin, F; Malpuech, G; Chazal, J; Carla, H; Chopard, P; Foulon, E; Goddon, R; Goumy, P

1995-07-01

The specificity of childhood cancers led to the creation of regional childhood cancer registries. An epidemiological study of childhood cancers in the Auvergne area was carried out over a 6 year-period (1986-1991) in order to create a registry. The population of our study was 252,820 children (0-15 years old), living in the Auvergne region. All malignant neoplasms were included together with brain tumours (whatever grading). Data were collected from medical and administrative sources. The data of 153 cases were collected during this period. World age standardized overall incidence rate was 120.5 cases/milion/year. Age standardized incidence rates were: leukemias 37.6 (ALL 28.01), central nervous system tumours 18.34 (medulloblastomas 4.6, astrocytomas 4.6, ependymomas 3.8), lymphomas 10.0, neuroblastomas 18.6, soft tissue tumors 8.3, bone tumours 6.1 (Ewing's sarcomas 4.1, osteosarcomas 2.0), nephroblastomas 5.5, retinoblastomas 3.1, liver tumours 0.5 and others 0.5. Our data base in the Auvergne area might be a source of information for epidemiological studies on the role of etiological factors, the survival, the sequelae and the incidence trends.

THE EDUCATIONAL MEDIA INDEX.

ERIC Educational Resources Information Center

Educational Media Council, Inc., New York, NY.

THIS 14-VOLUME SERIES INCLUDES TITLES AND DESCRIPTIONS FOR ALL CURRENT AND GENERALLY AVAILABLE EDUCATIONAL MEDIA, EXCLUDING STANDARD PRINT MATERIALS. EACH VOLUME COVERS A SPECIFIC SUBJECT AREA, LISTS TITLES ALPHABETICALLY AND BY SUBJECT, DESCRIBES EACH ENTRY, AND LISTS NAMES AND ADDRESSES OF SOURCES FOR THE MATERIALS. VOLUME 14 IS A CUMULATIVE…

40 CFR 63.11566 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information § 63.11566 What definitions apply to this subpart? Asphalt coating equipment means the saturators, coating mixers, and coaters used to apply asphalt...

40 CFR 63.11566 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information § 63.11566 What definitions apply to this subpart? Asphalt coating equipment means the saturators, coating mixers, and coaters used to apply asphalt...

40 CFR 63.11566 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information § 63.11566 What definitions apply to this subpart? Asphalt coating equipment means the saturators, coating mixers, and coaters used to apply asphalt...

40 CFR 63.11566 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information § 63.11566 What definitions apply to this subpart? Asphalt coating equipment means the saturators, coating mixers, and coaters used to apply asphalt...

40 CFR 412.46 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... production areas. There must be no discharge of manure, litter, or process wastewater pollutants into waters... practice effluent limitations designed to ensure no discharge of manure, litter, or process wastewater... such effluent limitations, “no discharge of manure, litter, or process wastewater pollutants,” as used...

40 CFR 63.11405 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false What definitions apply to this subpart? 63.11405 Section 63.11405 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Carbon Black Production Area Sources...

40 CFR 440.14 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (2) In the event that the annual precipitation falling on the treatment facility and the drainage area contributing surface runoff to the treatment facility exceeds the annual evaporation, a volume of water equal to the difference between annual precipitation falling on the treatment facility and the...

76 FR 38747 - Review of New Sources and Modifications in Indian Country

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-01

...The EPA is finalizing a Federal Implementation Plan (FIP) under the Clean Air Act (CAA or Act) for Indian country. The FIP includes two New Source Review (NSR) regulations for the protection of air resources in Indian country. The first rule applies to new and modified minor stationary sources (minor sources) and to minor modifications at existing major stationary sources (major sources) throughout Indian country. The second rule (nonattainment major NSR rule) applies to new and modified major sources in areas of Indian country that are designated as not attaining the National Ambient Air Quality Standards (NAAQS). These rules will be implemented by EPA or a delegate Tribal agency assisting EPA with administration of the rules, until replaced by an EPA-approved implementation plan.

Do the enigmatic ``Infrared-Faint Radio Sources'' include pulsars?

NASA Astrophysics Data System (ADS)

Hobbs, George; Middelberg, Enno; Norris, Ray; Keith, Michael; Mao, Minnie; Champion, David

2009-04-01

The Australia Telescope Large Area Survey (ATLAS) team have surveyed seven square degrees of sky at 1.4GHz. During processing some unexpected infrared-faint radio sources (IFRS sources) were discovered. The nature of these sources is not understood, but it is possible that some of these sources may be pulsars within our own galaxy. We propose to observe the IFRS sources with steep spectral indices using standard search techniques to determine whether or not they are pulsars. A pulsar detection would 1) remove a subset of the IFRS sources from the ATLAS sample so they would not need to be observed with large optical/IR telescopes to find their hosts and 2) be intrinsically interesting as the pulsar would be a millisecond pulsar and/or have an extreme spatial velocity.

Building a robust, scalable and standards-driven infrastructure for secondary use of EHR data: the SHARPn project.

PubMed

Rea, Susan; Pathak, Jyotishman; Savova, Guergana; Oniki, Thomas A; Westberg, Les; Beebe, Calvin E; Tao, Cui; Parker, Craig G; Haug, Peter J; Huff, Stanley M; Chute, Christopher G

2012-08-01

The Strategic Health IT Advanced Research Projects (SHARP) Program, established by the Office of the National Coordinator for Health Information Technology in 2010 supports research findings that remove barriers for increased adoption of health IT. The improvements envisioned by the SHARP Area 4 Consortium (SHARPn) will enable the use of the electronic health record (EHR) for secondary purposes, such as care process and outcomes improvement, biomedical research and epidemiologic monitoring of the nation's health. One of the primary informatics problem areas in this endeavor is the standardization of disparate health data from the nation's many health care organizations and providers. The SHARPn team is developing open source services and components to support the ubiquitous exchange, sharing and reuse or 'liquidity' of operational clinical data stored in electronic health records. One year into the design and development of the SHARPn framework, we demonstrated end to end data flow and a prototype SHARPn platform, using thousands of patient electronic records sourced from two large healthcare organizations: Mayo Clinic and Intermountain Healthcare. The platform was deployed to (1) receive source EHR data in several formats, (2) generate structured data from EHR narrative text, and (3) normalize the EHR data using common detailed clinical models and Consolidated Health Informatics standard terminologies, which were (4) accessed by a phenotyping service using normalized data specifications. The architecture of this prototype SHARPn platform is presented. The EHR data throughput demonstration showed success in normalizing native EHR data, both structured and narrative, from two independent organizations and EHR systems. Based on the demonstration, observed challenges for standardization of EHR data for interoperable secondary use are discussed. Copyright © 2012 Elsevier Inc. All rights reserved.

Building a robust, scalable and standards-driven infrastructure for secondary use of EHR data: The SHARPn project

PubMed Central

Rea, Susan; Pathak, Jyotishman; Savova, Guergana; Oniki, Thomas A.; Westberg, Les; Beebe, Calvin E.; Tao, Cui; Parker, Craig G.; Haug, Peter J.; Huff, Stanley M.; Chute, Christopher G.

2016-01-01

The Strategic Health IT Advanced Research Projects (SHARP) Program, established by the Office of the National Coordinator for Health Information Technology in 2010 supports research findings that remove barriers for increased adoption of health IT. The improvements envisioned by the SHARP Area 4 Consortium (SHARPn) will enable the use of the electronic health record (EHR) for secondary purposes, such as care process and outcomes improvement, biomedical research and epidemiologic monitoring of the nation’s health. One of the primary informatics problem areas in this endeavor is the standardization of disparate health data from the nation’s many health care organizations and providers. The SHARPn team is developing open source services and components to support the ubiquitous exchange, sharing and reuse or ‘liquidity’ of operational clinical data stored in electronic health records. One year into the design and development of the SHARPn framework, we demonstrated end to end data flow and a prototype SHARPn platform, using thousands of patient electronic records sourced from two large healthcare organizations: Mayo Clinic and Intermountain Healthcare. The platform was deployed to (1) receive source EHR data in several formats, (2) generate structured data from EHR narrative text, and (3) normalize the EHR data using common detailed clinical models and Consolidated Health Informatics standard terminologies, which were (4) accessed by a phenotyping service using normalized data specifications. The architecture of this prototype SHARPn platform is presented. The EHR data throughput demonstration showed success in normalizing native EHR data, both structured and narrative, from two independent organizations and EHR systems. Based on the demonstration, observed challenges for standardization of EHR data for interoperable secondary use are discussed. PMID:22326800

RACT/BACT/LAER Clearninghouse (RBLC)

EPA Pesticide Factsheets

OAR's RACT, BACT, LAER Clearinghouse (RBLC) data asset contains summary information on selected air permitting actions from EPA, state, and local permitting agencies across the U.S., as well as a number of international permit records supplied by air pollution control agencies in Mexico and Canada. The acronyms refer to program requirements of the New Source Review (NSR) program: RACT is Reasonably Available Control Technology and applies to existing sources in areas that are not meeting national ambient air quality standards (i.e., non-attainment areas); BACT is Best Available Control Technology and applies to major new or modified sources in clean areas (i.e., attainment areas). LAER, or Lowest Achievable Emission Rate, is required on major new or modified sources in non-attainment areas. As of 2012, RBLC includes approximately 6,500 entries. With the exception of LAER permit determinations, whose inclusion in RBLC is mandatory, participation is voluntary. Coverage is therefore not complete or necessarily representative.Required under Section 108 of the 1990 Amendments to the Clean Air Act, RBLC provides users 00e2?? typically permit writers, permit applicants or holders, and the public 00e2?? with references and personal contacts to support ongoing air pollution control activities. Information is detailed enough for users to know whether a permit is applicable to their needs. Users may then contact the appropriate agency to access the permit or discuss it wit

77 FR 38399 - Approval and Promulgation of Implementation Plans; Arizona; Nogales PM10

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-27

...EPA is proposing to approve a state implementation plan revision submitted by the Arizona Department of Environmental Quality to address the moderate area PM10, particulate matter with an aerodynamic diameter of less than or equal to a nominal ten micrometers, planning requirements for the Nogales nonattainment area. Consistent with this proposal, EPA is also proposing to approve the following plan elements as meeting the requirements of the Clean Air Act: the Nogales nonattainment area 2008 and 2011 emission inventories; the demonstration that the Nogales nonattainment area is attaining the National Ambient Air Quality Standard for PM10, but for international emissions sources in Nogales, Mexico; the demonstration that reasonably available control measures sufficient to meet the standard have been implemented in the nonattainment area; the reasonable further progress demonstration; the demonstration that implementation of measures beyond those needed for attainment meet the contingency measure requirement; and, the motor vehicle emissions budget for the purposes of determining the conformity of transportation plans, programs, and projects with this PM10 plan.

Lead sources, behaviors, and socioeconomic factors in relation to blood lead of native american and white children: a community-based assessment of a former mining area.

PubMed

Malcoe, Lorraine Halinka; Lynch, Robert A; Keger, Michelle Crozier; Skaggs, Valerie J

2002-04-01

Lead poisoning prevention requires knowledge of lead sources and of appropriate residential lead standards. Data are severely lacking on lead sources for Native American children, many of whom live in rural areas. Further, the relation of mining waste to blood lead concentrations (BPbs) of rural children is controversial. In collaboration with the eight tribes of northeastern Oklahoma, we assessed lead sources and their effects on BPbs for rural Native American and White children living in a former mining region. Venous blood lead, residential environmental (soil, dust, paint, water), and caregiver interview (e.g., hand-to-mouth behaviors, socioeconomic conditions) data were obtained from a representative sample of 245 children 1-6 years of age. BPbs ranged from 1 to 24 microg/dL. There were no ethnic differences in BPbs (p= 0.48) nor any patterns of excess lead sources for Native American or White children. Multiple linear regression analyses indicated that mean soil lead, mean floor lead loading, mouthing behaviors, caregivers' education, and residence in former mining towns were all strongly associated with BPbs. Logistic regression results showed mean floor dust lead loading greater than or equal to 10.1 microg/ft(2) (odds ratio [OR], 11.4; 95% confidence interval [CI], 3.5-37.3), and yard soil lead >165.3 mg/kg (OR, 4.1; CI, 1.3-12.4) were independently associated with BPbs greater than or equal to 10 microg/dL. We also found strong interactions between soil lead and poverty (p= 0.005), and dust and soil sources (p= 0.02). Our findings indicate that soil and dust lead derived largely from mining waste pose a health hazard to Native American and White children, and that current residential dust lead standards are insufficient to adequately protect children. Moreover, our finding that poor children are especially vulnerable to lead exposures suggests that residential standards should consider interactions among socioeconomic conditions and lead sources if environmental justice is to be achieved.

Source apportionment of PM10 by positive matrix factorization in urban area of Mumbai, India.

PubMed

Gupta, Indrani; Salunkhe, Abhaysinh; Kumar, Rakesh

2012-01-01

Particulate Matter (PM(10)) has been one of the main air pollutants exceeding the ambient standards in most of the major cities in India. During last few years, receptor models such as Chemical Mass Balance, Positive Matrix Factorization (PMF), PCA-APCS and UNMIX have been used to provide solutions to the source identification and contributions which are accepted for developing effective and efficient air quality management plans. Each site poses different complexities while resolving PM(10) contributions. This paper reports the variability of four sites within Mumbai city using PMF. Industrial area of Mahul showed sources such as residual oil combustion and paved road dust (27%), traffic (20%), coal fired boiler (17%), nitrate (15%). Residential area of Khar showed sources such as residual oil combustion and construction (25%), motor vehicles (23%), marine aerosol and nitrate (19%), paved road dust (18%) compared to construction and natural dust (27%), motor vehicles and smelting work (25%), nitrate (16%) and biomass burning and paved road dust (15%) in Dharavi, a low income slum residential area. The major contributors of PM(10) at Colaba were marine aerosol, wood burning and ammonium sulphate (24%), motor vehicles and smelting work (22%), Natural soil (19%), nitrate and oil burning (18%).

Dust loading of the normal atmosphere

NASA Astrophysics Data System (ADS)

Hall, F. F., Jr.

1983-01-01

Soil dust can contribute to atmospheric turbidity over most of the globe. The major sources of this dust are in the world's arid regions, where loadings of over 1000 micrograms/cu m can occur during strong winds. Saharan dust transported across the Atlantic can produce loadings up to 100 micrograms/cu m in the Western Hemisphere. Asian sources yield springtime loadings of 5-10 micrograms/cu m at Midway Island. Other important sources of dust are agricultural plowing and vehicular traffic on graded roads. The U.S. air quality standard of 75 micrograms/cu m is often exceeded in rural areas.

Chemometric evaluation of nitrate contamination in the groundwater of a hard rock area in Dharapuram, south India

NASA Astrophysics Data System (ADS)

Sajil Kumar, P. J.; Jegathambal, P.; James, E. J.

2014-12-01

This paper presents the results of investigations on groundwater nitrate contamination in the Dharapuram area of Tamil Nadu in south India as a primary step to initiate denitrification. Groundwater samples were collected from 26 selected locations during the pre-monsoon season in July 2010 and analysed for nitrate and other water quality parameters. Two important water types were identified, viz. Ca-Na-HCO3 and mixed Ca-Mg-Cl. It is found that the majority of samples possess high nitrate concentration; 57 % of samples exceeded the permissible limit of Indian (45 mg/L) and WHO (50 mg/L) drinking water standard. Spatial distribution map of NO3 suggested that major contamination was observed in the SW and NW parts of the study area. This result was in agreement with the corresponding land-use pattern in this study area. Denitrification process at greater depths was evident from the negative correlation between NO3 and well depth. The sources and controlling factors of high nitrate were investigated using cross plots of NO3 with other selected hydrochemical parameters. Positive correlation for NO3 was observed with EC, K, Cl and SO4. This analysis was capable of differentiating the various sources of nitrate in groundwater. The major sources of nitrate contamination are identified as areas of high fertilizer application, sewages and animal waste dumping yards. Regulation of these pollutant sources with appropriate and cost-effective denitrification process can restore the water quality in this area.

40 CFR 63.11502 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

...: process knowledge, an engineering assessment, or test data. Byproduct means a chemical (liquid, gas, or... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources... system(s); (5) A gas stream routed to other processes for reaction or other use in another process (i.e...

Predicting Debris-Slide Locations in Northwestern California

Treesearch

Mark E. Reid; Stephen D. Ellen; Dianne L. Brien; Juan de la Fuente; James N. Falls; Billie G. Hicks; Eric C. Johnson

2007-01-01

We tested four topographic models for predicting locations of debris-slide sources: 1) slope; 2) proximity to stream; 3) SHALSTAB with "standard" parameters; and 4) debris-slide-prone landforms, which delineates areas similar to "inner gorge" and "headwall swale" using experience-based rules. These approaches were compared in three diverse...

40 CFR 434.53 - Effluent limitations guidelines representing the degree of effluent reduction attainable by...

Code of Federal Regulations, 2013 CFR

2013-07-01

... economically achievable (BAT). 434.53 Section 434.53 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) COAL MINING POINT SOURCE CATEGORY BPT, BAT, BCT... economically achievable (BAT). (a) Reclamation areas. The limitations of this subsection apply to discharges...

40 CFR 63.11583 - What are my monitoring requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations... methods described in paragraphs (a), (b) or (c) of this section while equipment within a chemical... applicable, and the following: (1) Locate the pressure sensor(s) in, or as close as possible to, a position...

40 CFR 63.11583 - What are my monitoring requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations... methods described in paragraphs (a), (b) or (c) of this section while equipment within a chemical... applicable, and the following: (1) Locate the pressure sensor(s) in, or as close as possible to, a position...

40 CFR 63.11583 - What are my monitoring requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations... methods described in paragraphs (a), (b) or (c) of this section while equipment within a chemical... applicable, and the following: (1) Locate the pressure sensor(s) in, or as close as possible to, a position...

44 CFR 201.4 - Standard State Mitigation Plans.

Code of Federal Regulations, 2010 CFR

2010-10-01

... resources to reducing the effects of natural hazards. (b) Planning process. An effective planning process is... mitigation as well as to development in hazard-prone areas; a discussion of State funding capabilities for... identified. (iv) Identification of current and potential sources of Federal, State, local, or private funding...

44 CFR 201.4 - Standard State Mitigation Plans.

Code of Federal Regulations, 2013 CFR

2013-10-01

... resources to reducing the effects of natural hazards. (b) Planning process. An effective planning process is... mitigation as well as to development in hazard-prone areas; a discussion of State funding capabilities for... identified. (iv) Identification of current and potential sources of Federal, State, local, or private funding...

40 CFR 52.1683 - Control strategy: Ozone.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) New York § 52.1683 Control strategy: Ozone. (a) The State of New York has certified to the satisfaction of the EPA that no sources are... ozone nonattainment areas in New York listed below have attained the 1-hour ozone standard on the date...

40 CFR 63.11421 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false Am I subject to this subpart? 63.11421 Section 63.11421 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Hazardous Air Pollutants for Lead Acid Battery Manufacturing Area Sources...

Proceedings of the symposium: The Forested Wetlands of the Southern United States

Treesearch

Donald D. Hook; Russ Lea; [Editors

1989-01-01

Twenty-five papers are presented in five categories: Non point Sources of Pollution and the Functions and Values; Best Management Practices for Forested Wetlands; Streamside Management Strategies; Sensitive Areas Management; and Balancing Best Management Practices and Water Quality Standards for Feasibility, Economic, and Functional Effectiveness.

77 FR 29167 - Effluent Limitations Guidelines and New Source Performance Standards for the Airport Deicing...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-16

... reductions in dissolved oxygen, fish kills, reduced organism abundance and species diversity, contamination... 13045: Protection of Children From Environmental Health and Safety Risks H. EO 13211: Energy Effects I... water in residential areas and parkland, and other effects. Today, EPA is promulgating effluent...

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4) Dross furnace charging location; (5) Blast furnace and dross furnace tapping location; (6) Sinter machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) The...

40 CFR 63.11435 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Clay Ceramics Manufacturing Area Sources... if you own or operate a clay ceramics manufacturing facility (as defined in § 63.11444), with an atomized glaze spray booth or kiln that fires glazed ceramic ware, that processes more than 45 megagrams...

40 CFR 63.11398 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Acrylic and Modacrylic Fibers Production Area Sources Other Requirements and Information § 63.11398 What definitions apply to this subpart? Acrylic fiber means a manufactured synthetic fiber in which the fiber-forming substance is any long-chain...

40 CFR 63.11398 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Acrylic and Modacrylic Fibers Production Area Sources Other Requirements and Information § 63.11398 What definitions apply to this subpart? Acrylic fiber means a manufactured synthetic fiber in which the fiber-forming substance is any long-chain...

40 CFR 412.21 - Special definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... STANDARDS CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.21 Special definitions. For the purposes of this subpart: (a) Dry lot means a facility for growing ducks in confinement... for raising ducks which is open to the environment, has a small number of sheltered areas, and with...

40 CFR 412.21 - Special definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... STANDARDS CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.21 Special definitions. For the purposes of this subpart: (a) Dry lot means a facility for growing ducks in confinement... for raising ducks which is open to the environment, has a small number of sheltered areas, and with...

40 CFR 412.21 - Special definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... STANDARDS CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.21 Special definitions. For the purposes of this subpart: (a) Dry lot means a facility for growing ducks in confinement... for raising ducks which is open to the environment, has a small number of sheltered areas, and with...

40 CFR 412.21 - Special definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... STANDARDS CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.21 Special definitions. For the purposes of this subpart: (a) Dry lot means a facility for growing ducks in confinement... for raising ducks which is open to the environment, has a small number of sheltered areas, and with...

40 CFR 412.21 - Special definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... STANDARDS CONCENTRATED ANIMAL FEEDING OPERATIONS (CAFO) POINT SOURCE CATEGORY Ducks § 412.21 Special definitions. For the purposes of this subpart: (a) Dry lot means a facility for growing ducks in confinement... for raising ducks which is open to the environment, has a small number of sheltered areas, and with...

40 CFR Table 1 to Subpart Ssssss... - Emission Limits

Code of Federal Regulations, 2012 CFR

2012-07-01

... SSSSSS of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area Sources Pt. 63, Subpt. SSSSSS, Table 1 Table 1 to Subpart SSSSSS of Part 63—Emission Limits As required in § 63.11451, you must...

40 CFR Table 1 to Subpart Ssssss... - Emission Limits

Code of Federal Regulations, 2011 CFR

2011-07-01

... SSSSSS of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area Sources Pt. 63, Subpt. SSSSSS, Table 1 Table 1 to Subpart SSSSSS of Part 63—Emission Limits As required in § 63.11451, you must...

40 CFR Table 1 to Subpart Ssssss... - Emission Limits

Code of Federal Regulations, 2013 CFR

2013-07-01

... SSSSSS of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area Sources Pt. 63, Subpt. SSSSSS, Table 1 Table 1 to Subpart SSSSSS of Part 63—Emission Limits As required in § 63.11451, you must...

40 CFR Table 1 to Subpart Ssssss... - Emission Limits

Code of Federal Regulations, 2014 CFR

2014-07-01

... SSSSSS of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area Sources Pt. 63, Subpt. SSSSSS, Table 1 Table 1 to Subpart SSSSSS of Part 63—Emission Limits As required in § 63.11451, you must...

40 CFR Table 1 to Subpart Ssssss... - Emission Limits

Code of Federal Regulations, 2010 CFR

2010-07-01

... SSSSSS of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area Sources Pt. 63, Subpt. SSSSSS, Table 1 Table 1 to Subpart SSSSSS of Part 63—Emission Limits As required in § 63.11451, you must...

40 CFR 440.44 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... December 3, 1982. (2) In the event that the annual precipitation falling on the treatment facility and the drainage area contributing surface runoff to the treatment facility exceeds the annual evaporation, a volume of water equal to the difference between annual precipitation falling on the treatment facility...

75 FR 11461 - Approval and Promulgation of Air Quality Implementation Plans; Minnesota

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-11

... Promulgation of Air Quality Implementation Plans; Minnesota AGENCY: Environmental Protection Agency (EPA.... Because the PM 10 emission limits are being reduced, the air quality of Ramsey County will be protected... culpable source in the Childs Road area's nonattainment of the PM 10 National Ambient Air Quality Standards...

Elevated Arsenic and Uranium Concentrations in Unregulated Water Sources on the Navajo Nation, USA.

PubMed

Hoover, Joseph; Gonzales, Melissa; Shuey, Chris; Barney, Yolanda; Lewis, Johnnye

2017-01-01

Regional water pollution and use of unregulated water sources can be an important mixed metals exposure pathway for rural populations located in areas with limited water infrastructure and an extensive mining history. Using censored data analysis and mapping techniques we analyzed the joint geospatial distribution of arsenic and uranium in unregulated water sources throughout the Navajo Nation, where over 500 abandoned uranium mine sites are located in the rural southwestern United States. Results indicated that arsenic and uranium concentrations exceeded national drinking water standards in 15.1 % (arsenic) and 12.8 % (uranium) of tested water sources. Unregulated sources in close proximity (i.e., within 6 km) to abandoned uranium mines yielded significantly higher concentrations of arsenic or uranium than more distant sources. The demonstrated regional trends for potential co-exposure to these chemicals have implications for public policy and future research. Specifically, to generate solutions that reduce human exposure to water pollution from unregulated sources in rural areas, the potential for co-exposure to arsenic and uranium requires expanded documentation and examination. Recommendations for prioritizing policy and research decisions related to the documentation of existing health exposures and risk reduction strategies are also provided.

Socio-economic effect on socially-deprived communities of developing drinking water quality problems in arid and semi-arid area of central Rajasthan

NASA Astrophysics Data System (ADS)

Husain, I.; Husain, J.; Arif, M.

2014-09-01

Rajasthan is well known for its Great Thar desert. Central Rajasthan has an arid to semi-arid environment. The area faces either scarcity of water or poor quality of drinking water. In some areas water is transported 2 km or more, which uses time, energy and money. Rich people have their own sources, which is restricted for use by others. Such conditions are affecting socially-deprived communities, both socially and economically. Groundwater is a major source of drinking water due to the unavailability of surface water. There is a lack of groundwater quality knowledge in the community and the data available is hard to understand by consumers. The CCME Water Quality Index is a tool to simplify the water quality report by rating the water on quality standards. It provides meaningful summaries of overall water quality and trends, which is accessible to non-technical lay people. In the present study the objective is to examine the groundwater quality of six districts (Ajmer, Bhilwara, Pali, Rajasamand, Nagaur and Jodhpur), centrally located in Rajasthan, with arid and semi-arid conditions. CCME WQI is also evaluated to produce quality data in a form to be understood by the community. A total of 4369 groundwater sources in 1680 villages from six districts (76 546 km2) were collected and examined. Results are outlined in the Bureau of Indian Standards (BIS: 10500, 2012) and 2952 sources are unsafe for drinking. According to CCME WQI groundwater of 93 villages is poor, 343 villages are marginal, and 369 villages are fair in quality. Toxicological studies of unsafe drinking water and their remedial measures are also discussed. A tentative correlation between prevailing water-borne diseases and quality parameter has also been shown

Hydrogen maser frequency standard computer model for automatic cavity tuning servo simulations

NASA Technical Reports Server (NTRS)

Potter, P. D.; Finnie, C.

1978-01-01

A computer model of the JPL hydrogen maser frequency standard was developed. This model allows frequency stability data to be generated, as a function of various maser parameters, many orders of magnitude faster than these data can be obtained by experimental test. In particular, the maser performance as a function of the various automatic tuning servo parameters may be readily determined. Areas of discussion include noise sources, first-order autotuner loop, second-order autotuner loop, and a comparison of the loops.

[Air pollution in an urban area nearby the Rome-Ciampino city airport].

PubMed

Di Menno di Bucchianico, Alessandro; Cattani, Giorgio; Gaeta, Alessandra; Caricchia, Anna Maria; Troiano, Francesco; Sozzi, Roberto; Bolignano, Andrea; Sacco, Fabrizio; Damizia, Sesto; Barberini, Silvia; Caleprico, Roberta; Fabozzi, Tina; Ancona, Carla; Ancona, Laura; Cesaroni, Giulia; Forastiere, Francesco; Gobbi, Gian Paolo; Costabile, Francesca; Angelini, Federico; Barnaba, Francesca; Inglessis, Marco; Tancredi, Francesco; Palumbo, Lorenzo; Fontana, Luca; Bergamaschi, Antonio; Iavicoli, Ivo

2014-01-01

to assess air pollution spatial and temporal variability in the urban area nearby the Ciampino International Airport (Rome) and to investigate the airport-related emissions contribute. the study domain was a 64 km2 area around the airport. Two fifteen-day monitoring campaigns (late spring, winter) were carried out. Results were evaluated using several runs outputs of an airport-related sources Lagrangian particle model and a photochemical model (the Flexible Air quality Regional Model, FARM). both standard and high time resolution air pollutant concentrations measurements: CO, NO, NO2, C6H6, mass and number concentration of several PM fractions. 46 fixed points (spread over the study area) of NO2 and volatile organic compounds concentrations (fifteen days averages); deterministic models outputs. standard time resolution measurements, as well as model outputs, showed the airport contribution to air pollution levels being little compared to the main source in the area (i.e. vehicular traffic). However, using high time resolution measurements, peaks of particles associated with aircraft takeoff (total number concentration and soot mass concentration), and landing (coarse mass concentration) were observed, when the site measurement was downwind to the runway. the frequently observed transient spikes associated with aircraft movements could lead to a not negligible contribute to ultrafine, soot and coarse particles exposure of people living around the airport. Such contribute and its spatial and temporal variability should be investigated when assessing the airports air quality impact.

Experimental investigation on water quality standard of Yangtze River water source heat pump.

PubMed

Qin, Zenghu; Tong, Mingwei; Kun, Lin

2012-01-01

Due to the surface water in the upper reaches of Yangtze River in China containing large amounts of silt and algae, high content of microorganisms and suspended solids, the water in Yangtze River cannot be used for cooling a heat pump directly. In this paper, the possibility of using Yangtze River, which goes through Chongqing, a city in southwest China, as a heat source-sink was investigated. Water temperature and quality of the Yangtze River in the Chongqing area were analyzed and the performance of water source heat pump units in different sediment concentrations, turbidity and algae material conditions were tested experimentally, and the water quality standards, in particular surface water conditions, in the Yangtze River region that adapt to energy-efficient heat pumps were also proposed. The experimental results show that the coefficient of performance heat pump falls by 3.73% to the greatest extent, and the fouling resistance of cooling water in the heat exchanger increases up to 25.6% in different water conditions. When the sediment concentration and the turbidity in the river water are no more than 100 g/m3 and 50 NTU respectively, the performance of the heat pump is better, which can be used as a suitable river water quality standard for river water source heat pumps.

DEVELOPMENT OF THE MODEL OF GALACTIC INTERSTELLAR EMISSION FOR STANDARD POINT-SOURCE ANALYSIS OF FERMI LARGE AREA TELESCOPE DATA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Acero, F.; Ballet, J.; Ackermann, M.

2016-04-01

Most of the celestial γ rays detected by the Large Area Telescope (LAT) on board the Fermi Gamma-ray Space Telescope originate from the interstellar medium when energetic cosmic rays interact with interstellar nucleons and photons. Conventional point-source and extended-source studies rely on the modeling of this diffuse emission for accurate characterization. Here, we describe the development of the Galactic Interstellar Emission Model (GIEM), which is the standard adopted by the LAT Collaboration and is publicly available. This model is based on a linear combination of maps for interstellar gas column density in Galactocentric annuli and for the inverse-Compton emission producedmore » in the Galaxy. In the GIEM, we also include large-scale structures like Loop I and the Fermi bubbles. The measured gas emissivity spectra confirm that the cosmic-ray proton density decreases with Galactocentric distance beyond 5 kpc from the Galactic Center. The measurements also suggest a softening of the proton spectrum with Galactocentric distance. We observe that the Fermi bubbles have boundaries with a shape similar to a catenary at latitudes below 20° and we observe an enhanced emission toward their base extending in the north and south Galactic directions and located within ∼4° of the Galactic Center.« less

Development of the Model of Galactic Interstellar Emission for Standard Point-Source Analysis of Fermi Large Area Telescope Data

NASA Technical Reports Server (NTRS)

Acero, F.; Ackermann, M.; Ajello, M.; Albert, A.; Baldini, L.; Ballet, J.; Barbiellini, G.; Bastieri, D.; Bellazzini, R.; Brandt, T. J.;

Occurrence of bacteria in Blue Marsh Lake and selected tributaries, Berks County, Pennsylvania; September-October 2001

USGS Publications Warehouse

Zimmerman, Michele L.

2002-01-01

The Commonwealth of Pennsylvania has water-quality standards that limit the number of specific bacteria in water that is considered safe for recreational use. Bacteria such as fecal streptococci, fecal coliforms, and Escherichia coli (E. coli) are used to assess recreational water quality because they usually live in the intestines of warm-blooded animals. Fecal indicator bacteria commonly are associated with waterborne disease-causing organisms (pathogens). These indicator bacteria are used routinely as a measure of the quality of water for recreational activities such as swimming, boating, and water skiing. If the indicator bacteria are present, effective measures could be taken to prevent the transmission or epidemic outbreak of waterborne diseases as a result of contamination of these waters from human or animal waste.Blue Marsh Lake is on Tulpehocken Creek in Berks County, Pa., and drains a largely agricultural basin. Land use in the basin is approximately 60 percent cropland, and 85 percent of the farms are livestock and poultry farms.The potential sources of fecal bacteria are:geese that inhabit the recreational areas of the lake,humans that visit the Dry Brooks Day Use Area (swimming area), andfarm animals, wastewater facilities, and household septic systems in the basin (bacteria from these sources could enter the lake through tributaries).To meet the recreational water-quality standard, lake water may not have more than 200 colony-forming units (CFU) of fecal coliforms per 100 milliliters (mL). During the week of July 23, 2001, data collected by the U.S. Army Corps of Engineers (USACE) at the swimming area at Blue Marsh Lake showed concentrations of fecal coliforms in the water exceeding the standard. To determine the extent of elevated concentrations of fecal indicator bacteria, further study of the lake and selected tributaries was needed.

[Distribution characteristics of polycyclic aromatic hydrocarbons in runoff from the middle line source area of south-to-north water diversion project].

PubMed

Tai, Chao; Zhang, Kun-Feng; Zhou, Tian-Jian; Zhao, Tong-Qian; Wang, Qing-Qing; He, Xiao-Qi

2011-07-01

The distribution characteristics of polycyclic aromatic hydrocarbons in runoff from the middle line source area of south-to-north water diversion project were studied. Five groups of artificial runoff fields were established to collect runoff based on the different types of land-use, the contents of 16 USEPA priority PAHs in the runoff were determined using GC/MS method. The results showed that the average concentrations of PAHs of the aqueous phase in the collected runoff samples of different land-use types decreased in the order:cultivated land (26.53 ng x L(-1)) > oak forest (20.91 ng x L(-1)) > orchard (17.59 ng x L(-1)), and the average concentrations of PAHs of the particle phase were cultivated land (1 073.72 ng x g(-1)) > orchard (652.29 ng x g(-1)) > oak forest (385.46 ng x g(-1)). The high carcinogenic components Bap were detected in both run off of cultivated land and orchard with a detected rate of 30%. According to National Recommended Water Quality Standards of priority toxic pollutants (2006 USEPA), it was found that Chr exceed standard 40%, with a detected rate of 100%. It was also found that the runoff volume and the total PAHs content in runoff increase with the slope, and PAHs loss and slope were closely related in same land-use types. Based on the Molecular Markers Indicative Law, it can be concluded that the dominant source of PAHs in runoff of study area was combustion of coal, and a small amount came from vehicle exhaust emissions. There is a certain degree of ecological risk about runoff PAHs pollution in the study area, which is worth further attention.

Polycyclic aromatic hydrocarbons in the urban atmosphere of Nepal: Distribution, sources, seasonal trends, and cancer risk.

PubMed

Pokhrel, Balram; Gong, Ping; Wang, Xiaoping; Wang, Chuanfei; Gao, Shaoping

2018-03-15

Atmospheric polycyclic aromatic hydrocarbons (PAHs) in urban areas have always been a global concern, as these areas are considered to be the source region. Despite studies on the concentrations of PAHs in water, soils and sediments, knowledge of the distribution patterns, seasonality and sources of PAHs in urban areas of Nepal remains limited. In this study, polyurethane foam passive air samplers were used to measure gas-phase PAH concentrations over different land types in three major cities of Nepal-namely, Kathmandu (the capital) and Pokhara (both densely populated cities), and Hetauda (an agricultural city). The average concentrations of ∑15PAHs in ng/m 3 were 16.1±7.0 (6.4-28.6), 14.1±6.2 (6.8-29.4) and 11.1±9.0 (4.1-38.0) in Kathmandu, Pokhara and Hetauda, respectively. Molecular diagnostic ratio analysis suggested that fossil fuel combustion was a common PAH source for all three cities. In addition to this, coal combustion in Kathmandu, vehicle emissions in Pokhara, and grass/wood combustion in Hetauda were also possible sources of PAHs. In terms of cancer risk from PAH inhalation, a religious site with intense incense burning, a brick production area where extensive coal combustion is common, and a market place with heavy traffic emission, were associated with a higher risk than other areas. There were no clear seasonal trends in atmospheric PAHs. The estimated cancer risk due to inhalation of gas-phase PAHs exceeded the USEPA standard at >90% of the sites. Copyright © 2017 Elsevier B.V. All rights reserved.

Sensitivity of WRF-chem predictions to dust source function specification in West Asia

NASA Astrophysics Data System (ADS)

Nabavi, Seyed Omid; Haimberger, Leopold; Samimi, Cyrus

2017-02-01

Dust storms tend to form in sparsely populated areas covered by only few observations. Dust source maps, known as source functions, are used in dust models to allocate a certain potential of dust release to each place. Recent research showed that the well known Ginoux source function (GSF), currently used in Weather Research and Forecasting Model coupled with Chemistry (WRF-chem), exhibits large errors over some regions in West Asia, particularly near the IRAQ/Syrian border. This study aims to improve the specification of this critical part of dust forecasts. A new source function based on multi-year analysis of satellite observations, called West Asia source function (WASF), is therefore proposed to raise the quality of WRF-chem predictions in the region. WASF has been implemented in three dust schemes of WRF-chem. Remotely sensed and ground-based observations have been used to verify the horizontal and vertical extent and location of simulated dust clouds. Results indicate that WRF-chem performance is significantly improved in many areas after the implementation of WASF. The modified runs (long term simulations over the summers 2008-2012, using nudging) have yielded an average increase of Spearman correlation between observed and forecast aerosol optical thickness by 12-16 percent points compared to control runs with standard source functions. They even outperform MACC and DREAM dust simulations over many dust source regions. However, the quality of the forecasts decreased with distance from sources, probably due to deficiencies in the transport and deposition characteristics of the forecast model in these areas.

Open Source and Open Standard based decision support system: the example of lake Verbano floods management.

NASA Astrophysics Data System (ADS)

Cannata, Massimiliano; Antonovic, Milan; Pozzoni, Maurizio; Graf, Andrea

2015-04-01

The Locarno area (Switzerland, Canton Ticino) is exposed to lacual floods with a return period of about 7-8 years. The risk is of particular concern because the area is located in a floodplain that registered in the last decades a great increase in settlement and values of the real estates. Moreover small differences in lake altitude may produce a significant increase in flooded area due to the very low average slope of the terrain. While fatalities are not generally registered, several important economic costs are associated, e.g.: damages to real estates, interruption of activities, evacuation and relocation and environmental damages. While important events were registered in 1978, 1993, 2000, 2002 and 2014 the local stakeholder invested time and money in the set-up of an up-to-date decision support system that allows for the reduction of risks. Thanks to impressive technological advances the visionary concept of the Digital Earth (Gore 1992, 1998) is being realizing: geospatial coverages and monitoring systems data are increasingly available on the Web, and more importantly, in a standard format. As a result, today is possible to develop innovative decision support systems (Molinari et al. 2013) which mesh-up several information sources and offers special features for risk scenarios evaluation. In agreement with the exposed view, the authors have recently developed a new Web system whose design is based on the Service Oriented Architecture pattern. Open source software (e.g.: Geoserver, PostGIS, OpenLayers) has been used throughout the whole system and geospatial Open Standards (e.g.: SOS, WMS, WFS) are the pillars it rely on. SITGAP 2.0, implemented in collaboration with the Civil protection of Locarno e Vallemaggia, combines a number of data sources such as the Federal Register of Buildings and Dwellings, the Cantonal Register of residents, the Cadastral Surveying, the Cantonal Hydro-meteorological monitoring observations, the Meteoswiss weather forecasts, and others. As a result of this orchestration of data, SITGAP 2.0 serves features that allows, for example, to be informed on active alarms, to visualize lake level forecasts and associated flooding areas, to evaluate and map exposed elements and people, to plan and manage evacuation by searching for people living in particular areas or buildings, by registering evacuation actions and by searching for evacuated people. System architecture and functionalities, and consideration on the integration and accessibility of the beneath information together with the lesson learnt during the usage of the system during the last floods of November 2014, provides interesting discussion points for the identification of current and future needs.

Statistical considerations for grain-size analyses of tills

USGS Publications Warehouse

Jacobs, A.M.

1971-01-01

Relative percentages of sand, silt, and clay from samples of the same till unit are not identical because of different lithologies in the source areas, sorting in transport, random variation, and experimental error. Random variation and experimental error can be isolated from the other two as follows. For each particle-size class of each till unit, a standard population is determined by using a normally distributed, representative group of data. New measurements are compared with the standard population and, if they compare satisfactorily, the experimental error is not significant and random variation is within the expected range for the population. The outcome of the comparison depends on numerical criteria derived from a graphical method rather than on a more commonly used one-way analysis of variance with two treatments. If the number of samples and the standard deviation of the standard population are substituted in a t-test equation, a family of hyperbolas is generated, each of which corresponds to a specific number of subsamples taken from each new sample. The axes of the graphs of the hyperbolas are the standard deviation of new measurements (horizontal axis) and the difference between the means of the new measurements and the standard population (vertical axis). The area between the two branches of each hyperbola corresponds to a satisfactory comparison between the new measurements and the standard population. Measurements from a new sample can be tested by plotting their standard deviation vs. difference in means on axes containing a hyperbola corresponding to the specific number of subsamples used. If the point lies between the branches of the hyperbola, the measurements are considered reliable. But if the point lies outside this region, the measurements are repeated. Because the critical segment of the hyperbola is approximately a straight line parallel to the horizontal axis, the test is simplified to a comparison between the means of the standard population and the means of the subsample. The minimum number of subsamples required to prove significant variation between samples caused by different lithologies in the source areas and sorting in transport can be determined directly from the graphical method. The minimum number of subsamples required is the maximum number to be run for economy of effort. ?? 1971 Plenum Publishing Corporation.

Microbial source tracking: a forensic technique for microbial source identification?

PubMed

Stapleton, Carl M; Wyer, Mark D; Kay, David; Crowther, John; McDonald, Adrian T; Walters, Martin; Gawler, Andrew; Hindle, Terry

2007-05-01

As the requirements of the Water Framework Directive (WFD) and the US Clean Water Act (USCWA) for the maintenance of microbiological water quality in 'protected areas' highlight, there is a growing recognition that integrated management of point and diffuse sources of microbial pollution is essential. New information on catchment microbial dynamics and, in particular, the sources of faecal indicator bacteria found in bathing and shellfish harvesting waters is a pre-requisite for the design of any 'programme of measures' at the drainage basin scale to secure and maintain compliance with existing and new health-based microbiological standards. This paper reports on a catchment-scale microbial source tracking (MST) study in the Leven Estuary drainage basin, northwest England, an area for which quantitative faecal indicator source apportionment empirical data and land use information were also collected. Since previous MST studies have been based on laboratory trials using 'manufactured' samples or analyses of spot environmental samples without the contextual microbial flux data (under high and low flow conditions) and source information, such background data are needed to evaluate the utility of MST in USCWA total maximum daily load (TMDL) assessments or WFD 'Programmes of Measures'. Thus, the operational utility of MST remains in some doubt. The results of this investigation, using genotyping of Bacteroidetes using polymerase chain reaction (PCR) and male-specific ribonucleic acid coliphage (F + RNA coliphage) using hybridisation, suggest some discrimination is possible between livestock- and human-derived faecal indicator concentrations but, in inter-grade areas, the degree to which the tracer picture reflected the land use pattern and probable faecal indicator loading were less distinct. Interestingly, the MST data was more reliable on high flow samples when much of the faecal indicator flux from catchment systems occurs. Whilst a useful supplementary tool, the MST information did not provide quantitative source apportionment for the study catchment. Thus, it could not replace detailed empirical measurement of microbial flux at key catchment outlets to underpin faecal indicator source apportionment. Therefore, the MST techniques reported herein currently may not meet the standards required to be a useful forensic tool, although continued development of the methods and further catchment scale studies could increase confidence in such methods for future application.

Relationship between land-use and sources and fate of nitrate in groundwater in a typical recharge area of the North China Plain.

PubMed

Wang, Shiqin; Zheng, Wenbo; Currell, Matthew; Yang, Yonghui; Zhao, Huan; Lv, Mengyu

2017-12-31

Identification of different nitrate sources in groundwater is challenging in areas with diverse land use and multiple potential inputs. An area with mixed land-uses, typical of the piedmont-plain recharge area of the North China Plain, was selected to investigate different nitrate sources and the impact of land use on nitrate distribution in groundwater. Multiple environmental tracers were examined, including major ions, stable isotopes of water (δ 2 H-H 2 O, δ 18 O-H 2 O) and nitrate (δ 15 N-NO 3 - and δ 18 O-NO 3 - ). Groundwater was sampled from four land-use types; natural vegetation (NV), farmland (FL), economic forestland (EF) and residential areas (RA). A mixing model using δ 18 O and Cl - concentrations showed that groundwater recharge predominantly comprises precipitation and lateral groundwater flow from areas of natural vegetation in the upper catchment, while irrigation return water and wastewater from septic tanks were major inputs in farmland and residential areas, respectively. Land use variation is the major contributing factor to different nitrate concentrations. In total, 80%, 49% and 86% of samples from RA, FL and EF, respectively exceeded the WHO standard (50mg/L NO 3 - ), compared to 6.9% of samples from NV. Isotopes of δ 15 N-NO 3 - and δ 18 O-NO 3 - verified that nitrate in groundwater of the NV (with δ 15 N ranging from 1.7‰ to 4.7‰) was sourced from soil and precipitation. Examination of δ 15 N-NO 3 - vs δ 18 O-NO 3 - values along with multivariate statistical analysis (principle component and cluster analysis) helped identify sources with overlapping isotopic values in other land-use areas (where δ 15 N values range from 2.5‰ to 10.2‰). Manure and septic waste were dominant sources for most groundwater with high NO 3 - and Cl - concentrations in both farmland and residential areas. The lack of de-nitrification and fact that the area is a recharge zone for the North China Plain highlight the importance of controlling nitrate sources through careful application of manure and fertilizers, and control of septic leakage. Copyright © 2017 Elsevier B.V. All rights reserved.

Dispersion modeling of polycyclic aromatic hydrocarbons from combustion of biomass and fossil fuels and production of coke in Tianjin, China.

PubMed

Tao, Shu; Li, Xinrong; Yang, Yu; Coveney, Raymond M; Lu, Xiaoxia; Chen, Haitao; Shen, Weiran

2006-08-01

A USEPA, procedure, ISCLT3 (Industrial Source Complex Long-Term), was applied to model the spatial distribution of polycyclic aromatic hydrocarbons (PAHs) emitted from various sources including coal, petroleum, natural gas, and biomass into the atmosphere of Tianjin, China. Benzo[a]pyrene equivalent concentrations (BaPeq) were calculated for risk assessment. Model results were provisionally validated for concentrations and profiles based on the observed data at two monitoring stations. The dominant emission sources in the area were domestic coal combustion, coke production, and biomass burning. Mainly because of the difference in the emission heights, the contributions of various sources to the average concentrations at receptors differ from proportions emitted. The shares of domestic coal increased from approximately 43% at the sources to 56% at the receptors, while the contributions of coking industry decreased from approximately 23% at the sources to 7% at the receptors. The spatial distributions of gaseous and particulate PAHs were similar, with higher concentrations occurring within urban districts because of domestic coal combustion. With relatively smaller contributions, the other minor sources had limited influences on the overall spatial distribution. The calculated average BaPeq value in air was 2.54 +/- 2.87 ng/m3 on an annual basis. Although only 2.3% of the area in Tianjin exceeded the national standard of 10 ng/m3, 41% of the entire population lives within this area.

Surface area and the seabed area, volume, depth, slope, and topographic variation for the world's seas, oceans, and countries.

PubMed

Costello, Mark John; Cheung, Alan; De Hauwere, Nathalie

2010-12-01

Depth and topography directly and indirectly influence most ocean environmental conditions, including light penetration and photosynthesis, sedimentation, current movements and stratification, and thus temperature and oxygen gradients. These parameters are thus likely to influence species distribution patterns and productivity in the oceans. They may be considered the foundation for any standardized classification of ocean ecosystems and important correlates of metrics of biodiversity (e.g., species richness and composition, fisheries). While statistics on ocean depth and topography are often quoted, how they were derived is rarely cited, and unless calculated using the same spatial resolution the resulting statistics will not be strictly comparable. We provide such statistics using the best available resolution (1-min) global bathymetry, and open source digital maps of the world's seas and oceans and countries' Exclusive Economic Zones, using a standardized methodology. We created a terrain map and calculated sea surface and seabed area, volume, and mean, standard deviation, maximum, and minimum, of both depth and slope. All the source data and our database are freely available online. We found that although the ocean is flat, and up to 71% of the area has a < 1 degree slope. It had over 1 million approximately circular features that may be seamounts or sea-hills as well as prominent mountain ranges or ridges. However, currently available global data significantly underestimate seabed slopes. The 1-min data set used here predicts there are 68,669 seamounts compared to the 30,314 previously predicted using the same method but lower spatial resolution data. The ocean volume exceeds 1.3 billion km(3) (or 1.3 sextillion liters), and sea surface and seabed areas over 354 million km(2). We propose the coefficient of variation of slope as an index of topographic heterogeneity. Future studies may improve on this database, for example by using a more detailed bathymetry, and in situ measured data. The database could be used to classify ocean features, such as abyssal plains, ridges, and slopes, and thus provide the basis for a standards based classification of ocean topography.

Hanford Site Air Operating Permit Application Supplemental Information [Sec 1 Thru 5] Vol 1 Thru 3 Appendices A Thru C

DOE Office of Scientific and Technical Information (OSTI.GOV)

CURN, B.L.

2000-05-01

This report documents radionuclide air emissions from the Hanford Site in 1998 and the resulting effective dose equivalent to the maximally exposed individual (MEI) member of the public. The report has been prepared in accordance with the Code of Federal Regulations, Title 40, Protection of the Environment, Part 61, National Emission Standards for Hazardous Air Pollutants (40 CFR 61), Subpart H: ''National Emission Standards for Emissions of Radionuclides Other than Radon from Department of Energy Facilities,'' and with the Washington Administrative Code Chapter 246247, Radiation Protection - Air Emissions. The federal regulations in 40 CFR 61, Subpart H, require themore » measurement and reporting of radionuclides emitted from Department of Energy facilities and the resulting offsite dose from those emissions. A standard of 10 mrem/yr effective dose equivalent (EDE) is imposed on them. The EDE to the MEI due to routine emissions in 1998 from Hanford Site point sources was 1.3 E-02 mrem (1.3 E-04 mSv). which is 0.13 percent of the federal standard. Chapter 246-247 of the Washington Administrative Code (WAC) requires the reporting of radionuclide emissions from all Department of Energy Hanford Site sources. The state has adopted into these regulations the 40 CFR 61 standard of 10 mrem/yr EDE. The EDE to the MEI attributable to diffuse and fugitive radionuclide air emissions from the Hanford Site in 1998 was 2.5 E-02 mrem (2.S E-04 mSv). This dose added to the dose from point sources gives a total for all sources of 3.8 E-02 mrem/yr (3.8 E-04 mSv) EDE. which is 0.38 percent of the 10 mrem/yr standard. An unplanned release on August 26, 1998, in the 300 Area of the Hanford Site resulted in a potential dose of 4.1 E-02 mrem to a hypothetical individual at the nearest point of public access to that area. This hypothetical individual was not the MEI since the wind direction on the day of the release was away from the MEI residence. The potential dose from the unplanned event was similar in magnitude to that from routine releases during 1998. Were the release from this unplanned event combined with routine releases, the total dose would be less than 1 percent of the 10 mrem/yr standard.« less

40 CFR 52.1683 - Control strategy: Ozone.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Ozone. 52.1683...: Ozone. (a) The State of New York has certified to the satisfaction of the EPA that no sources are... ozone nonattainment areas in New York listed below have attained the 1-hour ozone standard on the date...

40 CFR 52.1683 - Control strategy: Ozone.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 4 2013-07-01 2013-07-01 false Control strategy: Ozone. 52.1683...: Ozone. (a) The State of New York has certified to the satisfaction of the EPA that no sources are... ozone nonattainment areas in New York listed below have attained the 1-hour ozone standard on the date...

40 CFR 52.1683 - Control strategy: Ozone.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 4 2012-07-01 2012-07-01 false Control strategy: Ozone. 52.1683...: Ozone. (a) The State of New York has certified to the satisfaction of the EPA that no sources are... ozone nonattainment areas in New York listed below have attained the 1-hour ozone standard on the date...

40 CFR 63.1340 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2013 CFR

2013-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants From the Portland Cement... this subpart apply to each new and existing portland cement plant which is a major source or an area... to and regulated under subpart EEE of this part; (2) Each clinker cooler at any portland cement plant...

40 CFR 63.1340 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants From the Portland Cement... this subpart apply to each new and existing portland cement plant which is a major source or an area... to and regulated under subpart EEE of this part; (2) Each clinker cooler at any portland cement plant...

42 CFR 482.41 - Condition of participation: Physical environment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... rooms, and stairwells. In all other areas not serviced by the emergency supply source, battery lamps and flashlights must be available. (2) There must be facilities for emergency gas and water supply. (b) Standard...; (ii) The dispensers are installed in a manner that minimizes leaks and spills that could lead to falls...

40 CFR 63.10685 - What are the requirements for the control of contaminants from scrap?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Area Sources: Electric Arc Furnace Steelmaking Facilities Standards and Compliance Requirements § 63..., lead, and free organic liquids. For metallic scrap utilized in the EAF at your facility, you must... scrap at your facility subject to paragraph (a)(1) of this section and other scrap subject to paragraph...

40 CFR 63.10685 - What are the requirements for the control of contaminants from scrap?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Area Sources: Electric Arc Furnace Steelmaking Facilities Standards and Compliance Requirements § 63..., lead, and free organic liquids. For metallic scrap utilized in the EAF at your facility, you must... scrap at your facility subject to paragraph (a)(1) of this section and other scrap subject to paragraph...

40 CFR 434.30 - Applicability; description of the acid or ferruginous mine drainage subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... BPT, BAT, BCT LIMITATIONS AND NEW SOURCE PERFORMANCE STANDARDS Acid or Ferruginous Mine Drainage § 434.30 Applicability; description of the acid or ferruginous mine drainage subcategory. The provisions of this subpart are applicable to acid or ferruginous mine drainage from an active mining area resulting...

40 CFR 434.30 - Applicability; description of the acid or ferruginous mine drainage subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... BPT, BAT, BCT LIMITATIONS AND NEW SOURCE PERFORMANCE STANDARDS Acid or Ferruginous Mine Drainage § 434.30 Applicability; description of the acid or ferruginous mine drainage subcategory. The provisions of this subpart are applicable to acid or ferruginous mine drainage from an active mining area resulting...

76 FR 15308 - Completion of the Requirement To Promulgate Emission Standards

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-21

... CONTACT: Mr. Nathan Topham, Sector Policies and Programs Division, Office of Air Quality Planning and... the aggregate area source emissions of each of the 30 urban hazardous air pollutants (HAP) are subject... list of the 30 urban HAP, please see National Air Toxics Program: The Integrate Urban Strategy, 64 FR...

40 CFR Table 2 of Subpart Bbbbbbb... - Initial Compliance Demonstration Methods With the Emission Reduction and PM Concentration...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry Other... less; or c. Provide engineering calculations, such as mass balance and flow rate calculations, that demonstrate that the control device is capable of reducing PM concentration from the chemical preparations...

40 CFR Table 2 of Subpart Bbbbbbb... - Initial Compliance Demonstration Methods With the Emission Reduction and PM Concentration...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry Other... less; or c. Provide engineering calculations, such as mass balance and flow rate calculations, that demonstrate that the control device is capable of reducing PM concentration from the chemical preparations...

40 CFR Table 2 of Subpart Bbbbbbb... - Initial Compliance Demonstration Methods With the Emission Reduction and PM Concentration...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry Other... less; or c. Provide engineering calculations, such as mass balance and flow rate calculations, that demonstrate that the control device is capable of reducing PM concentration from the chemical preparations...

40 CFR Table 2 of Subpart Bbbbbbb... - Initial Compliance Demonstration Methods With the Emission Reduction and PM Concentration...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry Other... less; or c. Provide engineering calculations, such as mass balance and flow rate calculations, that demonstrate that the control device is capable of reducing PM concentration from the chemical preparations...

40 CFR Table 2 of Subpart Bbbbbbb... - Initial Compliance Demonstration Methods With the Emission Reduction and PM Concentration...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry Other... less; or c. Provide engineering calculations, such as mass balance and flow rate calculations, that demonstrate that the control device is capable of reducing PM concentration from the chemical preparations...

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... paragraphs (a)(1) through (9) of this section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4... machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) No owner or operator of any existing, new, or reconstructed primary lead...

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... paragraphs (a)(1) through (9) of this section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4... machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) No owner or operator of any existing, new, or reconstructed primary lead...

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... paragraphs (a)(1) through (9) of this section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4... machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) No owner or operator of any existing, new, or reconstructed primary lead...

40 CFR Table 1 to Subpart Llllll... - Applicability of General Provisions to Subpart LLLLLL

Code of Federal Regulations, 2011 CFR

2011-07-01

... Modacrylic Fibers Production Area Sources Pt. 63, Subpt. LLLLLL, Table 1 Table 1 to Subpart LLLLLL of Part 63... not include opacity or visible emissions standards or require a continuous opacity monitoring system... does not require a continuous opacity monitoring system or continuous emissions monitoring system. 63.9...

40 CFR Table 1 to Subpart Llllll... - Applicability of General Provisions to Subpart LLLLLL

Code of Federal Regulations, 2010 CFR

2010-07-01

... Modacrylic Fibers Production Area Sources Pt. 63, Subpt. LLLLLL, Table 1 Table 1 to Subpart LLLLLL of Part 63... not include opacity or visible emissions standards or require a continuous opacity monitoring system... does not require a continuous opacity monitoring system or continuous emissions monitoring system. 63.9...

40 CFR Table 4 of Subpart Bbbbbbb... - Continuous Compliance Demonstration Methods With the Emission Reduction and PM Concentration...

Code of Federal Regulations, 2010 CFR

2010-07-01

... chemical preparations operation was in target HAP service. The control device monitoring data are averaged... Emission Standards for Hazardous Air Pollutants for Area Sources: Chemical Preparations Industry Other... particulate matter control device being used. c. A CPMS, and maintaining records of data verifying that the...

40 CFR 63.5870 - How do I calculate annual uncontrolled and controlled organic HAP emissions from my wet-out area...

Code of Federal Regulations, 2010 CFR

2010-07-01

... SOURCE CATEGORIES National Emissions Standards for Hazardous Air Pollutants: Reinforced Plastic... according to usage within each end product/thickness combination. (3) For each end product/thickness combination being produced, select the formula with the highest usage rate for testing. (4) If not already...

Identifing Atmospheric Pollutant Sources Using Artificial Neural Networks

NASA Astrophysics Data System (ADS)

Paes, F. F.; Campos, H. F.; Luz, E. P.; Carvalho, A. R.

2008-05-01

The estimation of the area source pollutant strength is a relevant issue for atmospheric environment. This characterizes an inverse problem in the atmospheric pollution dispersion. In the inverse analysis, an area source domain is considered, where the strength of such area source term is assumed unknown. The inverse problem is solved by using a supervised artificial neural network: multi-layer perceptron. The conection weights of the neural network are computed from delta rule - learning process. The neural network inversion is compared with results from standard inverse analysis (regularized inverse solution). In the regularization method, the inverse problem is formulated as a non-linear optimization approach, whose the objective function is given by the square difference between the measured pollutant concentration and the mathematical models, associated with a regularization operator. In our numerical experiments, the forward problem is addressed by a source-receptor scheme, where a regressive Lagrangian model is applied to compute the transition matrix. The second order maximum entropy regularization is used, and the regularization parameter is calculated by the L-curve technique. The objective function is minimized employing a deterministic scheme (a quasi-Newton algorithm) [1] and a stochastic technique (PSO: particle swarm optimization) [2]. The inverse problem methodology is tested with synthetic observational data, from six measurement points in the physical domain. The best inverse solutions were obtained with neural networks. References: [1] D. R. Roberti, D. Anfossi, H. F. Campos Velho, G. A. Degrazia (2005): Estimating Emission Rate and Pollutant Source Location, Ciencia e Natura, p. 131-134. [2] E.F.P. da Luz, H.F. de Campos Velho, J.C. Becceneri, D.R. Roberti (2007): Estimating Atmospheric Area Source Strength Through Particle Swarm Optimization. Inverse Problems, Desing and Optimization Symposium IPDO-2007, April 16-18, Miami (FL), USA, vol 1, p. 354-359.

DOE Office of Scientific and Technical Information (OSTI.GOV)

BENNETT,D.B.; PAQUETTE,D.E.; KLAUS,K.

The BNL water supply system meets all water quality standards and has sufficient pumping and storage capacity to meet current and anticipated future operational demands. Because BNL's water supply is drawn from the shallow Upper Glacial aquifer, BNL's source water is susceptible to contamination. The quality of the water supply is being protected through (1) a comprehensive program of engineered and operational controls of existing aquifer contamination and potential sources of new contamination, (2) groundwater monitoring, and (3) potable water treatment. The BNL Source Water Assessment found that the source water for BNL's Western Well Field (comprised of Supply Wellsmore » 4, 6, and 7) has relatively few threats of contamination and identified potential sources are already being carefully managed. The source water for BNL's Eastern Well Field (comprised of Supply Wells 10, 11, and 12) has a moderate number of threats to water quality, primarily from several existing volatile organic compound and tritium plumes. The g-2 Tritium Plume and portions of the Operable Unit III VOC plume fall within the delineated source water area for the Eastern Well Field. In addition, portions of the much slower migrating strontium-90 plumes associated with the Brookhaven Graphite Research Reactor, Waste Concentration Facility and Building 650 lie within the Eastern source water area. However, the rate of travel in the aquifer for strontium-90 is about one-twentieth of that for tritium and volatile organic compounds. The Laboratory has been carefully monitoring plume migration, and has made adjustments to water supply operations. Although a number of BNL's water supply wells were impacted by VOC contamination in the late 1980s, recent routine analysis of water samples from BNL's supply wells indicate that no drinking water standards have been reached or exceeded. The high quality of the water supply strongly indicates that the operational and engineered controls implemented over the past ten years have effectively protected the quality of the water supply.« less

Environmental impact of the Midia Port - Black Sea (Romania), on the coastal sediment quality

NASA Astrophysics Data System (ADS)

Catianis, Irina; Ungureanu, Constantin; Magagnini, Luca; Ulazzi, Elisa; Campisi, Tiziana; Stanica, Adrian

2016-03-01

The aim of the study was to evaluate the impact of potential pollution sources, mainly from the upstream anthropogenic sources and port-related activities. The in-vestigated area covered a wide range of anthropogenic im-pacts (e.g., industrial wastes, storm water runoff, acciden-tal oil spills, intentional discharges and shipping activities). The quality of water and Sediments was assessed us-ing Standard methods, as physical-chemical parameters, chemistry and biology (microbiology, ecotoxicology) aim-ing to figure the level of pollution and the effect of port-related activities. Seawater quality results agreed generally with environmental Standards. Though, in some samples the concentrations of sulphates (mg/1) and heavy metals (μg/1), as B, As and Se exceeded the recommended lim-its, without posing a serious environmental concern. Most of the surface sediment samples contain critical levels of hydrocarbons (C>12), (mg/kg), polycyclic aromatic hydrocarbons (ng/g) and polychlorobiphenyls (ng/g). For some heavy metals (mg/kg), exchangeable concentrations were found to be very close or above the regulations. The signifi-cance of this study is incontestable taking into account the lack of previous relevant historical data of this area. In this sense, it was possible to indicate, in general, good environmental conditions, despite the industrial and concentrated local port-related activities in the investigated area.

Wide-area situation awareness in electric power grid

NASA Astrophysics Data System (ADS)

Greitzer, Frank L.

2010-04-01

Two primary elements of the US energy policy are demand management and efficiency and renewable sources. Major objectives are clean energy transmission and integration, reliable energy transmission, and grid cyber security. Development of the Smart Grid seeks to achieve these goals by lowering energy costs for consumers, achieving energy independence and reducing greenhouse gas emissions. The Smart Grid is expected to enable real time wide-area situation awareness (SA) for operators. Requirements for wide-area SA have been identified among interoperability standards proposed by the Federal Energy Regulatory Commission and the National Institute of Standards and Technology to ensure smart-grid functionality. Wide-area SA and enhanced decision support and visualization tools are key elements in the transformation to the Smart Grid. This paper discusses human factors research to promote SA in the electric power grid and the Smart Grid. Topics that will be discussed include the role of human factors in meeting US energy policy goals, the impact and challenges for Smart Grid development, and cyber security challenges.

Effects of combined sewer overflow and stormwater on indicator bacteria concentrations in the Tama River due to the high population density of Tokyo Metropolitan area.

PubMed

Ham, Young-Sik; Kobori, Hiromi; Takasago, Masahisa

2009-05-01

The indicator bacteria (standard plate count, total coliform, and fecal coliform bacteria) concentrations have been investigated using six ambient habitats (population density, percent sewer penetration, stream flow rate (m(3)/sec), percent residential area, percent forest area and percent agricultural area) in the Tama River basin in Tokyo, Japan during June 2003 to January 2005. The downstream and tributary Tama River showed higher concentrations of TC and FC bacteria than the upstream waters, which exceeded an environmental quality standard for rivers and a bathing water quality criterion. It was estimated that combined sewer overflow (CSO) and stormwater effluents contributed -4-23% to the indicator bacteria concentrations of the Tama River. The results of multiple regression analyses show that the indicator bacteria concentrations of Tama River basin are significantly affected by population density. It is concluded that the Tama River received a significant bacterial contamination load originating from the anthropogenic source.

Multi-focus image fusion based on area-based standard deviation in dual tree contourlet transform domain

NASA Astrophysics Data System (ADS)

Dong, Min; Dong, Chenghui; Guo, Miao; Wang, Zhe; Mu, Xiaomin

2018-04-01

Multiresolution-based methods, such as wavelet and Contourlet are usually used to image fusion. This work presents a new image fusion frame-work by utilizing area-based standard deviation in dual tree Contourlet trans-form domain. Firstly, the pre-registered source images are decomposed with dual tree Contourlet transform; low-pass and high-pass coefficients are obtained. Then, the low-pass bands are fused with weighted average based on area standard deviation rather than the simple "averaging" rule. While the high-pass bands are merged with the "max-absolute' fusion rule. Finally, the modified low-pass and high-pass coefficients are used to reconstruct the final fused image. The major advantage of the proposed fusion method over conventional fusion is the approximately shift invariance and multidirectional selectivity of dual tree Contourlet transform. The proposed method is compared with wavelet- , Contourletbased methods and other the state-of-the art methods on common used multi focus images. Experiments demonstrate that the proposed fusion framework is feasible and effective, and it performs better in both subjective and objective evaluation.

GIS for the Gulf: A reference database for hurricane-affected areas: Chapter 4C in Science and the storms-the USGS response to the hurricanes of 2005

USGS Publications Warehouse

Greenlee, Dave

2007-01-01

A week after Hurricane Katrina made landfall in Louisiana, a collaboration among multiple organizations began building a database called the Geographic Information System for the Gulf, shortened to "GIS for the Gulf," to support the geospatial data needs of people in the hurricane-affected area. Data were gathered from diverse sources and entered into a consistent and standardized data model in a manner that is Web accessible.

Regional Geological Maps of the Northeast Pacific - Standard Navy Ocean Area NP-9

DTIC Science & Technology

1978-01-01

creates the next Washington, and British Columbia. All the land area, except island in the chain. Thus, many island chains, for example. the that seaward of...the San Andreas Fault of California, is part of Hawaiian Islands , seem to indicate the path of the plate over the North American Plate. such "hot...turbiditc deposition from the nearby been deposited by bottom currents, volcanic sources such as the Hawaiian Islands and from the deposition of sediments

Metrological activity determination of 133Ba by sum-peak absolute method

NASA Astrophysics Data System (ADS)

da Silva, R. L.; de Almeida, M. C. M.; Delgado, J. U.; Poledna, R.; Santos, A.; de Veras, E. V.; Rangel, J.; Trindade, O. L.

2016-07-01

The National Laboratory for Metrology of Ionizing Radiation provides gamma sources of radionuclide and standardized in activity with reduced uncertainties. Relative methods require standards to determine the sample activity while the absolute methods, as sum-peak, not. The activity is obtained directly with good accuracy and low uncertainties. 133Ba is used in research laboratories and on calibration of detectors for analysis in different work areas. Classical absolute methods don't calibrate 133Ba due to its complex decay scheme. The sum-peak method using gamma spectrometry with germanium detector standardizes 133Ba samples. Uncertainties lower than 1% to activity results were obtained.

Identification of watershed priority management areas under water quality constraints: A simulation-optimization approach with ideal load reduction

NASA Astrophysics Data System (ADS)

Dong, Feifei; Liu, Yong; Wu, Zhen; Chen, Yihui; Guo, Huaicheng

2018-07-01

Targeting nonpoint source (NPS) pollution hot spots is of vital importance for placement of best management practices (BMPs). Although physically-based watershed models have been widely used to estimate nutrient emissions, connections between nutrient abatement and compliance of water quality standards have been rarely considered in NPS hotspot ranking, which may lead to ineffective decision-making. It's critical to develop a strategy to identify priority management areas (PMAs) based on water quality response to nutrient load mitigation. A water quality constrained PMA identification framework was thereby proposed in this study, based on the simulation-optimization approach with ideal load reduction (ILR-SO). It integrates the physically-based Soil and Water Assessment Tool (SWAT) model and an optimization model under constraints of site-specific water quality standards. To our knowledge, it was the first effort to identify PMAs with simulation-based optimization. The SWAT model was established to simulate temporal and spatial nutrient loading and evaluate effectiveness of pollution mitigation. A metamodel was trained to establish a quantitative relationship between sources and water quality. Ranking of priority areas is based on required nutrient load reduction in each sub-watershed targeting to satisfy water quality standards in waterbodies, which was calculated with genetic algorithm (GA). The proposed approach was used for identification of PMAs on the basis of diffuse total phosphorus (TP) in Lake Dianchi Watershed, one of the three most eutrophic large lakes in China. The modeling results demonstrated that 85% of diffuse TP came from 30% of the watershed area. Compared with the two conventional targeting strategies based on overland nutrient loss and instream nutrient loading, the ILR-SO model identified distinct PMAs and narrowed down the coverage of management areas. This study addressed the urgent need to incorporate water quality response into PMA identification and showed that the ILR-SO approach is effective to guide watershed management for aquatic ecosystem restoration.

Hand dug wells in Namibia: An underestimated water source or a threat to human health?

NASA Astrophysics Data System (ADS)

Wanke, H.; Nakwafila, A.; Hamutoko, J. T.; Lohe, C.; Neumbo, F.; Petrus, I.; David, A.; Beukes, H.; Masule, N.; Quinger, M.

The rural population of parts of northern and western Namibia uses hand dug wells for their domestic water supply, partly because no other source (e.g., deep tube wells) is available, but also as a substitute for pipeline water that is often perceived as being too expensive. The water quality of these wells is usually not monitored or controlled, thus a study has been carried out in four study areas in Namibia: southern Omusati/Oshana area, Okongo/Ohangwena area, Omatjete/Omaruru area, Okanguati/Kunene area. Hand dug wells have been tested for on-site parameters: electric conductivity, pH and temperature while samples were taken for major inorganic constituents and several minor and trace constituents including fluoride and nitrate. In addition a sampling campaign in 2010 included the determination of coliform bacteria and Escherichia coli. Results were classified according to the Namibian Water Guidelines. The constituents making the water unfit for human consumption are fluoride, nitrate, sulphate and total dissolved solids. Contamination by E. coli was indicated in nearly all wells that are used for livestock watering. For the Omatjete/Omaruru study area an isotope based study on the source of nitrate has indicated manure as a source. The range of recharge values obtained for the studied villages ranges from 1 mm/a to locally more than 100 mm/a. Overall the water resource in the shallow perched aquifers in the study areas is in many places inappropriate for human consumption. Treatment to improve the quality or introduction of protection measures is necessary to bring this resource to an acceptable quality according to national and/or international standards.

Health risks of heavy metal exposure through vegetable consumption near a large-scale Pb/Zn smelter in central China.

PubMed

Li, Xinyu; Li, Zhonggen; Lin, Che-Jen; Bi, Xiangyang; Liu, Jinling; Feng, Xinbin; Zhang, Hua; Chen, Ji; Wu, Tingting

2018-06-04

Smelting of nonferrous metals is an important source of heavy metals in surface soil. The crops/vegetables grown on contaminated soil potentially impose adverse effects on human health. In this study, the contamination level of five heavy metals (Hg, Pb, Zn, Cd and Cu) in ten types of vegetables grown nearby a large scale Pb/Zn smelter in Hunan Province, China and the health risk associated with their consumption are assessed. Based on the data obtained from 52 samples, we find that Pb and Cd contributed to the greatest health risk and leafy vegetables tend to be more contaminated than non-leafy vegetables. Within 4 km radius of the smelter, over 75% of vegetable samples exceeded the national food standard for Pb; over 47% exceeded the Cd standard; and 7% exceeded the Hg standard. Heavy metal concentrations in vegetables measured within the 4 km radius are on average three times more elevated compared to those found at the control area 15 km away. Heavy metals in vegetables have dual sources of root absorption from soil and leaf adsorption from atmosphere. Health risk in terms of the hazard index (HI) at contaminated areas are 3.66 and 3.14 for adults and children, respectively, suggesting adverse health effects would occur. HI for both groups are mainly contributed by Pb (48%) and Cd (40%). Fortunately, vegetable samples collected at the control area are considered safe to consume. Copyright © 2018 Elsevier Inc. All rights reserved.

A field instrument for quantitative determination of beryllium by activation analysis

USGS Publications Warehouse

Vaughn, William W.; Wilson, E.E.; Ohm, J.M.

1960-01-01

A low-cost instrument has been developed for quantitative determinations of beryllium in the field by activation analysis. The instrument makes use of the gamma-neutron reaction between gammas emitted by an artificially radioactive source (Sb124) and beryllium as it occurs in nature. The instrument and power source are mounted in a panel-type vehicle. Samples are prepared by hand-crushing the rock to approximately ?-inch mesh size and smaller. Sample volumes are kept constant by means of a standard measuring cup. Instrument calibration, made by using standards of known BeO content, indicates the analyses are reproducible and accurate to within ? 0.25 percent BeO in the range from 1 to 20 percent BeO with a sample counting time of 5 minutes. Sensitivity of the instrument maybe increased somewhat by increasing the source size, the sample size, or by enlarging the cross-sectional area of the neutron-sensitive phosphor normal to the neutron flux.

Small satellites and space debris issues

NASA Astrophysics Data System (ADS)

Yakovlev, M.; Kulik, S.; Agapov, V.

2001-10-01

The objective of this report is the analysis of the tendencies in designing of small satellites (SS) and the effect of small satellites on space debris population. It is shown that SS to include nano- and pico-satellites should be considered as a particularly dangerous source of space debris when elaborating international standards and legal documents concerning the space debris problem, in particular "International Space Debris Mitigation Standard". These issues are in accordance with the IADC goals in its main activity areas and should be carefully considered within the IADC framework.

The need for a standard approach to assessing the functionality of rural community water supplies

NASA Astrophysics Data System (ADS)

Bonsor, Helen; MacDonald, Alan; Casey, Vincent; Carter, Richard; Wilson, Paul

2018-03-01

The Sustainable Development Goals have set an agenda for transformational change in water access, aiming for secure household connections globally. Despite this goal, communal groundwater supplies are likely to remain the main source of improved water supplies for many rural areas in Africa and South Asia for decades to come. Understanding the poor functionality of existing communal supplies remains, therefore, a priority. A critical first step is to establish a sector-wide definition of borehole supply functionality and a standard method of its assessment.

Assessment of arsenic, fluoride, bacteria, and other contaminants in drinking water sources for rural communities of Kasur and other districts in Punjab, Pakistan.

PubMed

Arshad, Nasima; Imran, Saiqa

2017-01-01

High levels of arsenic contamination in drinking water of two villages, Badarpur and Ibrahimabad of district Kasur, central Punjab, Pakistan is reported first time in present studies. Groundwater quality situation was found to be impaired when samples of different rural areas of district Kasur were monitored according to Pakistan Standards and Quality Control Authority (PSQCA) for all significant water quality constituents and analyzed for trace elements, physico-chemical, and microbiological parameters. Out of 35water sources, 97 % were found unsafe and only 3 % of the sources were within safe limits. High concentrations of arsenic, fluoride, and bacteria were found in 91, 74, and 77 % sources of drinking water, respectively. Very high concentrations of arsenic ranging 58-3800 μg/L were found in the water samples obtained from Badarpur and Ibrahimabad. A decrease in water contamination was observed with increase in source depth. The health issues like arsenicosis and skeletal/dental flourosis were observed in the residents of the monitored areas. Drinking water quality conditions of some rural areas of northen and southern districts of Punjab was also analyzed and compared with Kasur district. High levels of nitrates were found in the samples of Islamabad and Rawalpindi, while high levels of arsenic, iron, fluoride, and TDS were found in Bahawalpur district. Graphical abstract ᅟ.

76 FR 35806 - Amendments to National Emission Standards for Hazardous Air Pollutants for Area Sources: Plating...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-20

..., or Use I. National Technology Transfer Advancement Act J. Executive Order 12898: Federal Actions To... action under Executive Order 12866. I. National Technology Transfer Advancement Act Section 12(d) of the National Technology Transfer and Advancement Act (NTTAA) of 1995 (Pub. L. 104-113, section 12(d), 15 U.S.C...

40 CFR 421.305 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... off-gas wet air pollution control. PSES for the Primary and Secondary Titanium Subcategory Pollutant... pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122 Nickel 0.515 0.346 Titanium 0.496 0.215 (b) Chlorination Area-vent wet air pollution control. PSES for the Primary and Secondary...

40 CFR 421.304 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... air pollution control. NSPS Limitations for the Primary and Secondary Titanium Subcategory Pollutant... pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122 Nickel 0.515 0.346 Titanium 0.496... of 7.5 to 10.0 at all times. (b) Chlorination area-vent wet air pollution control. NSPS Limitations...

40 CFR 421.304 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... air pollution control. NSPS Limitations for the Primary and Secondary Titanium Subcategory Pollutant... pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122 Nickel 0.515 0.346 Titanium 0.496... of 7.5 to 10.0 at all times. (b) Chlorination area-vent wet air pollution control. NSPS Limitations...

40 CFR 421.305 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... off-gas wet air pollution control. PSES for the Primary and Secondary Titanium Subcategory Pollutant... pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122 Nickel 0.515 0.346 Titanium 0.496 0.215 (b) Chlorination Area-vent wet air pollution control. PSES for the Primary and Secondary...

Source Apportionment of Ambient Fine Particulate Matter in Dearborn, Michigan, using Hourly Resolved PM Chemical Composition Data

EPA Science Inventory

High time-resolution aerosol sampling was conducted for one month during July–August 2007 in Dearborn, MI, a non-attainment area for fine particulate matter (PM2.5) National Ambient Air Quality Standards (NAAQS). Measurements of more than 30 PM2.5 species were made using a suite o...

76 FR 57913 - Amendments to National Emission Standards for Hazardous Air Pollutants for Area Sources: Plating...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-19

... learned that plating or coating was also done for repair purposes, usually with small paint brushes and... include spray painting at ambient temperatures. After promulgation of the final rule, we learned that... polishing machine that emits one or more of the plating and polishing metal HAP, you must operate a capture...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2010 CFR

2010-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2013 CFR

2013-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2014 CFR

2014-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2011 CFR

2011-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2012 CFR

2012-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

Integrating multisource land use and land cover data

USGS Publications Warehouse

Wright, Bruce E.; Tait, Mike; Lins, K.F.; Crawford, J.S.; Benjamin, S.P.; Brown, Jesslyn F.

1995-01-01

As part of the U.S. Geological Survey's (USGS) land use and land cover (LULC) program, the USGS in cooperation with the Environmental Systems Research Institute (ESRI) is collecting and integrating LULC data for a standard USGS 1:100,000-scale product. The LULC data collection techniques include interpreting spectrally clustered Landsat Thematic Mapper (TM) images; interpreting 1-meter resolution digital panchromatic orthophoto images; and, for comparison, aggregating locally available large-scale digital data of urban areas. The area selected is the Vancouver, WA-OR quadrangle, which has a mix of urban, rural agriculture, and forest land. Anticipated products include an integrated LULC prototype data set in a standard classification scheme referenced to the USGS digital line graph (DLG) data of the area and prototype software to develop digital LULC data sets.This project will evaluate a draft standard LULC classification system developed by the USGS for use with various source material and collection techniques. Federal, State, and local governments, and private sector groups will have an opportunity to evaluate the resulting prototype software and data sets and to provide recommendations. It is anticipated that this joint research endeavor will increase future collaboration among interested organizations, public and private, for LULC data collection using common standards and tools.

Probabilistic seismic hazard assessments of Sabah, east Malaysia: accounting for local earthquake activity near Ranau

NASA Astrophysics Data System (ADS)

Khalil, Amin E.; Abir, Ismail A.; Ginsos, Hanteh; Abdel Hafiez, Hesham E.; Khan, Sohail

2018-02-01

Sabah state in eastern Malaysia, unlike most of the other Malaysian states, is characterized by common seismological activity; generally an earthquake of moderate magnitude is experienced at an interval of roughly every 20 years, originating mainly from two major sources, either a local source (e.g. Ranau and Lahad Dato) or a regional source (e.g. Kalimantan and South Philippines subductions). The seismicity map of Sabah shows the presence of two zones of distinctive seismicity, these zones are near Ranau (near Kota Kinabalu) and Lahad Datu in the southeast of Sabah. The seismicity record of Ranau begins in 1991, according to the international seismicity bulletins (e.g. United States Geological Survey and the International Seismological Center), and this short record is not sufficient for seismic source characterization. Fortunately, active Quaternary fault systems are delineated in the area. Henceforth, the seismicity of the area is thus determined as line sources referring to these faults. Two main fault systems are believed to be the source of such activities; namely, the Mensaban fault zone and the Crocker fault zone in addition to some other faults in their vicinity. Seismic hazard assessments became a very important and needed study for the extensive developing projects in Sabah especially with the presence of earthquake activities. Probabilistic seismic hazard assessments are adopted for the present work since it can provide the probability of various ground motion levels during expected from future large earthquakes. The output results are presented in terms of spectral acceleration curves and uniform hazard curves for periods of 500, 1000 and 2500 years. Since this is the first time that a complete hazard study has been done for the area, the output will be a base and standard for any future strategic plans in the area.

Water supply dynamics and quality of alternative water sources in low-income areas of Lilongwe City, Malawi

NASA Astrophysics Data System (ADS)

Chidya, Russel C. G.; Mulwafu, Wapulumuka O.; Banda, Sembeyawo C. T.

2016-06-01

Recent studies in many developing countries have shown that Small Scale Independent Providers (SSIPs) in low-income areas (LIAs) are practical alternatives to water utilities. This study explored supply dynamics and quality of alternative water sources in four LIAs of Lilongwe City in Malawi using qualitative and quantitative methods. Household-level surveys (n = 120) and transect walks were employed to determine the socio-economic activities in the areas. One-on-one discussions were made with water source owners (SSIPs) (n = 24). Data on policy and institutional frameworks was collected through desktop study and Key Informant Interviews (n = 25). Quality of the water sources (shallow wells and boreholes) was determined by collecting grab samples (n = 24) in triplicate using 500 mL bottles. Selected physico-chemical and microbiological parameters were measured: pH, EC, TDS, turbidity, water temperature, salinity, K, Na, Ca, Mg, Cl-, F-, NO3-, alkalinity, water hardness, Fecal coliform (FC) and Faecal Streptococci (FS) bacteria. Water quality data was compared with Malawi Bureau of Standards (MBS) and World Health Organization (WHO) guidelines for drinking water. Shallow wells were reported (65%, n = 120) to be the main source of water for household use in all areas. Some policies like prohibition of boreholes and shallow wells in City locations were in conflict with other provisions of water supply, sanitation and housing. High levels of FC (0-2100 cfu/100 mL) and FS (0-1490 cfu/100 mL) at several sites (>90%, n = 24) suggest water contamination likely to impact on human health. This calls for upgrading and recognition of the water sources for improved water service delivery.

A Workflow to Model Microbial Loadings in Watersheds ...

EPA Pesticide Factsheets

Many watershed models simulate overland and instream microbial fate and transport, but few actually provide loading rates on land surfaces and point sources to the water body network. This paper describes the underlying general equations for microbial loading rates associated with 1) land-applied manure on undeveloped areas from domestic animals; 2) direct shedding on undeveloped lands by domestic animals and wildlife; 3) urban or engineered areas; and 4) point sources that directly discharge to streams from septic systems and shedding by domestic animals. A microbial source module, which houses these formulations, is linked within a workflow containing eight models and a set of databases that form a loosely configured modeling infrastructure which supports watershed-scale microbial source-to-receptor modeling by focusing on animal-impacted catchments. A hypothetical example application – accessing, retrieving, and using real-world data – demonstrates the ability of the infrastructure to automate many of the manual steps associated with a standard watershed assessment, culminating with calibrated flow and microbial densities at the pour point of a watershed. Presented at 2016 Biennial Conference, International Environmental Modelling & Software Society.

Microbiological quality of Puget Sound Basin streams and identification of contaminant sources

USGS Publications Warehouse

Embrey, S.S.

2001-01-01

Fecal coliforms, Escherichia coli, enterococci, and somatic coliphages were detected in samples from 31 sites on streams draining urban and agricultural regions of the Puget Sound Basin Lowlands. Densities of bacteria in 48 and 71 percent of the samples exceeded U.S. Environmental Protection Agency's freshwater recreation criteria for Escherichia coli and enterococci, respectively, and 81 percent exceeded Washington State fecal coliform standards. Male-specific coliphages were detected in samples from 15 sites. Male-specific F+RNA coliphages isolated from samples taken at South Fork Thornton and Longfellow Creeks were serotyped as Group II, implicating humans as potential contaminant sources. These two sites are located in residential, urban areas. F+RNA coliphages in samples from 10 other sites, mostly in agricultural or rural areas, were serotyped as Group I, implicating non-human animals as likely sources. Chemicals common to wastewater, including fecal sterols, were detected in samples from several urban streams, and also implicate humans, at least in part, as possible sources of fecal bacteria and viruses to the streams.

A survey of spatially distributed exterior dust lead loadings in New York City

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caravanos, Jack; Weiss, Arlene L.; School of Medicine, New York University, NY 10016

This work documents ambient lead dust deposition values (lead loading) for the boroughs of New York City in 2003-2004. Currently, no regulatory standards exist for exterior concentrations of lead in settled dust. This is in contrast to the clearance and risk assessment standards that exist for interior residential dust. The reported potential for neurobehavioral toxicity and adverse cognitive development in children due to lead exposure prompts public health concerns about undocumented lead sources. Such sources may include settled dust of outdoor origin. Dust sampling throughout the five boroughs of NYC was done from the top horizontal portion of pedestrian trafficmore » control signals (PTCS) at selected street intersections along main thoroughfares. The data (n=214 samples) show that lead in dust varies within each borough with Brooklyn having the highest median concentration (730{mu}g/ft{sup 2}), followed in descending order by Staten Island (452{mu}g/ft{sup 2}), the Bronx (382{mu}g/ft{sup 2}), Queens (198{mu}g/ft{sup 2}) and finally, Manhattan (175{mu}g/ft{sup 2}). When compared to the HUD/EPA indoor lead in dust standard of 40{mu}g/ft{sup 2}, our data show that this value is exceeded in 86% of the samples taken. An effort was made to determine the source of the lead in the dust atop of the PTCS. The lead in the dust and the yellow signage paint (which contains lead) were compared using isotopic ratio analysis. Results showed that the lead-based paint chip samples from intact signage did not isotopically match the dust wipe samples taken from the same surface. We know that exterior dust containing lead contributes to interior dust lead loading. Therefore, settled leaded dust in the outdoor environment poses a risk for lead exposure to children living in urban areas, namely, areas with elevated childhood blood lead levels and background lead dust levels from a variety of unidentified sources.« less

A preliminary assessment of dispersion level of SO 2 in Fars industrial region, south of Iran, by GIS.

PubMed

Dehghani, Mansooreh; Taghizadeh, Mohammad Mehdi; Hashemi, Hassan; Rastgoo, Ebrahim

2013-01-01

The city of Zarghan is located 25 km northeast of Shiraz, southern Iran. Zarghan is affected by numerous pollution sources such as oil refinery, an industrial park, and Shiraz-Tehran highway. The numerous contaminating sources around Zarghan can cause serious local air pollution. Sulfur dioxide gas is an important index of air pollution in cities. Therefore, in order to control and manage Zarghan air quality, it is important to monitor sulfur dioxide concentration in the surrounding area. It is also essential to know about the contribution level of other sources of pollution as well as dispersion radius of pollutants in the area. In this study, the concentration of sulfur dioxide was measured by passive sampling at 10 different stations. These values were interpolated in other parts of the city using ArcGIS software. The results of sampling showed that the concentration of the gas was 60 µgm(-3) around oil refinery. The level was 19 µgm(-3) in region located about 3 km from the oil refinery. It was also demonstrated that the gas concentration was not higher than the standard limit within residential area. On the other hand, the role of the local highway and industrial park was not significant in contaminating air in urban areas.

A Preliminary Assessment of Dispersion Level of SO2 in Fars Industrial Region, South of Iran, by GIS

PubMed Central

Dehghani, Mansooreh; Taghizadeh, Mohammad Mehdi; Rastgoo, Ebrahim

2013-01-01

The city of Zarghan is located 25 km northeast of Shiraz, southern Iran. Zarghan is affected by numerous pollution sources such as oil refinery, an industrial park, and Shiraz-Tehran highway. The numerous contaminating sources around Zarghan can cause serious local air pollution. Sulfur dioxide gas is an important index of air pollution in cities. Therefore, in order to control and manage Zarghan air quality, it is important to monitor sulfur dioxide concentration in the surrounding area. It is also essential to know about the contribution level of other sources of pollution as well as dispersion radius of pollutants in the area. In this study, the concentration of sulfur dioxide was measured by passive sampling at 10 different stations. These values were interpolated in other parts of the city using ArcGIS software. The results of sampling showed that the concentration of the gas was 60 µgm−3 around oil refinery. The level was 19 µgm−3 in region located about 3 km from the oil refinery. It was also demonstrated that the gas concentration was not higher than the standard limit within residential area. On the other hand, the role of the local highway and industrial park was not significant in contaminating air in urban areas. PMID:24163700

Beyond Californium-A Neutron Generator Alternative for Dosimetry and Instrument Calibration in the U.S.

PubMed

Piper, Roman K; Mozhayev, Andrey V; Murphy, Mark K; Thompson, Alan K

2017-09-01

Evaluations of neutron survey instruments, area monitors, and personal dosimeters rely on reference neutron radiations, which have evolved from the heavy reliance on (α,n) sources to a shared reliance on (α,n) and the spontaneous fission neutrons of californium-252 (Cf). Capable of producing high dose equivalent rates from an almost point source geometry, the characteristics of Cf are generally more favorable when compared to the use of (α,n) and (γ,n) sources or reactor-produced reference neutron radiations. Californium-252 is typically used in two standardized configurations: unmoderated, to yield a fission energy spectrum; or with the capsule placed within a heavy-water moderating sphere to produce a softened spectrum that is generally considered more appropriate for evaluating devices used in nuclear power plant work environments. The U.S. Department of Energy Cf Loan/Lease Program, a longtime origin of affordable Cf sources for research, testing and calibration, was terminated in 2009. Since then, high-activity sources have become increasingly cost-prohibitive for laboratories that formerly benefited from that program. Neutron generators, based on the D-T and D-D fusion reactions, have become economically competitive with Cf and are recognized internationally as important calibration and test standards. Researchers from the National Institute of Standards and Technology and the Pacific Northwest National Laboratory are jointly considering the practicality and technical challenges of implementing neutron generators as calibration standards in the U.S. This article reviews the characteristics of isotope-based neutron sources, possible isotope alternatives to Cf, and the rationale behind the increasing favor of electronically generated neutron options. The evaluation of a D-T system at PNNL has revealed characteristics that must be considered in adapting generators to the task of calibration and testing where accurate determination of a dosimetric quantity is necessary. Finally, concepts are presented for modifying the generated neutron spectra to achieve particular targeted spectra, simulating Cf or workplace environments.

40 CFR 424.16 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS FERROALLOY MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.16 Pretreatment standards for new sources. Any new source... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Pretreatment standards for new sources...

40 CFR 420.44 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true New source performance standards (NSPS... GUIDELINES AND STANDARDS IRON AND STEEL MANUFACTURING POINT SOURCE CATEGORY Steelmaking Subcategory § 420.44 New source performance standards (NSPS). The discharge of wastewater pollutants from any new source...

Constraints as a destriping tool for Hires images

NASA Technical Reports Server (NTRS)

Cao, YU; Prince, Thomas A.

1994-01-01

Images produced from the Maximum Correlation Method sometimes suffer from visible striping artifacts, especially for areas of extended sources. Possible causes are different baseline levels and calibration errors in the detectors. We incorporated these factors into the MCM algorithm, and tested the effects of different constraints on the output image. The result shows significant visual improvement over the standard MCM Method. In some areas the new images show intelligible structures that are otherwise corrupted by striping artifacts, and the removal of these artifacts could enhance performance of object classification algorithms. The constraints were also tested on low surface brightness areas, and were found to be effective in reducing the noise level.

Maps of estimated nitrate and arsenic concentrations in basin-fill aquifers of the southwestern United States

USGS Publications Warehouse

Beisner, Kimberly R.; Anning, David W.; Paul, Angela P.; McKinney, Tim S.; Huntington, Jena M.; Bexfield, Laura M.; Thiros, Susan A.

2012-01-01

Human-health concerns and economic considerations associated with meeting drinking-water standards motivated a study of the vulnerability of basin-fill aquifers to nitrate contamination and arsenic enrichment in the southwestern United States. Statistical models were developed by using the random forest classifier algorithm to predict concentrations of nitrate and arsenic across a model grid representing about 190,600 square miles of basin-fill aquifers in parts of Arizona, California, Colorado, Nevada, New Mexico, and Utah. The statistical models, referred to as classifiers, reflect natural and human-related factors that affect aquifer vulnerability to contamination and relate nitrate and arsenic concentrations to explanatory variables representing local- and basin-scale measures of source and aquifer susceptibility conditions. Geochemical variables were not used in concentration predictions because they were not available for the entire study area. The models were calibrated to assess model accuracy on the basis of measured values.Only 2 percent of the area underlain by basin-fill aquifers in the study area was predicted to equal or exceed the U.S. Environmental Protection Agency drinking-water standard for nitrate as N (10 milligrams per liter), whereas 43 percent of the area was predicted to equal or exceed the standard for arsenic (10 micrograms per liter). Areas predicted to equal or exceed the drinking-water standard for nitrate include basins in central Arizona near Phoenix; the San Joaquin Valley, the Santa Ana Inland, and San Jacinto Basins of California; and the San Luis Valley of Colorado. Much of the area predicted to equal or exceed the drinking-water standard for arsenic is within a belt of basins along the western portion of the Basin and Range Physiographic Province that includes almost all of Nevada and parts of California and Arizona. Predicted nitrate and arsenic concentrations are substantially lower than the drinking-water standards in much of the study area-about 93 percent of the area underlain by basin-fill aquifers was less than one-half the standard for nitrate as N (5.0 milligrams per liter), and 50 percent was less than one-half the standard for arsenic (5.0 micrograms per liter). The predicted concentrations and the improved understanding of the susceptibility and vulnerability of southwestern basin-fill aquifers to nitrate contamination and arsenic enrichment can be used by water managers as a qualitative tool to assess and protect the quality of groundwater resources in the Southwest.

Modeling of lead air pollution. [Baton Rouge, Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Monteith, C.S.; Henry, J.M.

1982-05-01

A study was performed to determine whether vehicular emissions should be included with industrial emissions when demonstrating attainment of the ambient air quality standard for lead. The impact on ambient lead concentrations of the phaseout of leaded gasoline and improved automobile fuel economy was examined by modeling vehicular emissions for 1972 and 1978. Results show that while automobiles in the Baton Rouge area were a significant source of lead in 1972, the phaseout of leaded gasoline and the increase in fuel economy have resulted in a lower contribution (0.20 ..mu..g/m/sup 3/) by automobiles to the ambient lead concentration in 1978.more » The areas having the greatest potential for exceeding the ambient air quality standard can be identified using CDM (EPA's Climatological Dispersion Model). This information can be used to determine the optimal location for an ambient air monitor to demonstrate compliance with the ambient air quality standard. 9 references, 4 figures, 5 tables. (JMT)« less

[Pollution Assessment and Spatial Distribution Characteristics of Heavy Metals in Soils of Coal Mining Area in Longkou City].

PubMed

Liu, Shuo; Wu, Quan-yuan; Cao, Xue-jiang; Wang, Ji-ning; Zhang, Long-long; Cai, Dong-quan; Zhou, Li-yuan; Liu, Na

2016-01-15

The present paper takes the coal mining area of Longkou City as the research area. Thirty-six topsoil (0-20 cm) samples were collected and the contents of 5 kinds of heavy metals were determined, including Cd, As, Ni, Ph, Cr. Geo-statistics analysis was used to analyze the spatial distribution of heavy metals. Principal component analysis (PCA) was used to explore the pollution sources of heavy metals and the degree of heavy metals pollution was evaluated by weighted average comprehensive pollution evaluation method. The results showed that enrichment phenomenon was significant for the 5 kinds of heavy metals. Taking secondary standard of National Environment Quality Standard for Soil as the background value, their exceed standard rates were 72.22%, 100%, 100%, 91.67%, 100%, respectively. Average contents of heavy metals in the soil samples were all over the national standard level two and were 1.53, 11.86, 2.40, 1.31, 4.09 times of the background value. In addition, the average contents were much higher than the background value of the topsoil in the eastern part of Shandong Province and were 9.85, 39.98, 8.85, 4.29, 12.71 times of the background value. According to the semivariogram model, we obtained the nugget-effects of 5 kinds of heavy metals and their values were in the order of As (0.644) > Cd (0.627) > Cr (0.538) > Ni (0.411) > Pb (0.294), all belonging to moderate spatial correlation. On the whole, the central part of the Sangyuan Coal Mine and its surrounding areas were the most seriously polluted, while the pollution of heavy metals in the east and west of the study area was relatively light. Principal component analysis suggested that the enrichment of Cd, As, Ni, Cr was due to irrigation of wastewater, the discharge of industry and enterprise, and the industrial activity. Automobile exhaust and coal combustion were the main pollution sources of Pb. The single-factor assessment of heavy metals pollution showed that the degree of different heavy metals pollution was in the order of As > Cr > Ni > Cd > Pb. Simultaneously, comprehensive pollution evaluation showed that the degree of heavy metals pollution in the study area was very serious, with comprehensive pollution index ranging from 2.17 to 4.66, among which, the numbers of moderate and heavy pollution samples were 10 and 26, respectively. Areas with heavy pollution were mainly distributed in the Sangyuan Coal Mine, Beizao Coal Mine, Liuhai Coal Mine; and the areas with moderate pollution covered Wali Coal Mine, Liangjia Coal Mine, and other regions. The results of this paper will provide data reference and theoretical support for the study of ecological risk assessment in the study area.

Evaluation of Skin Surface as an Alternative Source of Reference DNA Samples: A Pilot Study.

PubMed

Albujja, Mohammed H; Bin Dukhyil, Abdul Aziz; Chaudhary, Abdul Rauf; Kassab, Ahmed Ch; Refaat, Ahmed M; Babu, Saranya Ramesh; Okla, Mohammad K; Kumar, Sachil

2018-01-01

An acceptable area for collecting DNA reference sample is a part of the forensic DNA analysis development. The aim of this study was to evaluate skin surface cells (SSC) as an alternate source of reference DNA sample. From each volunteer (n = 10), six samples from skin surface areas (forearm and fingertips) and two traditional samples (blood and buccal cells) were collected. Genomic DNA was extracted and quantified then genotyped using standard techniques. The highest DNA concentration of SSC samples was collected using the tape/forearm method of collection (2.1 ng/μL). Cotton swabs moistened with ethanol yielded higher quantities of DNA than swabs moistened with salicylic acid, and it gave the highest percentage of full STR profiles (97%). This study supports the use of SSC as a noninvasive sampling technique and as a extremely useful source of DNA reference samples among certain cultures where the use of buccal swabs can be considered socially unacceptable. © 2017 American Academy of Forensic Sciences.

SENSITIVITY OF BLIND PULSAR SEARCHES WITH THE FERMI LARGE AREA TELESCOPE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dormody, M.; Johnson, R. P.; Atwood, W. B.

2011-12-01

We quantitatively establish the sensitivity to the detection of young to middle-aged, isolated, gamma-ray pulsars through blind searches of Fermi Large Area Telescope (LAT) data using a Monte Carlo simulation. We detail a sensitivity study of the time-differencing blind search code used to discover gamma-ray pulsars in the first year of observations. We simulate 10,000 pulsars across a broad parameter space and distribute them across the sky. We replicate the analysis in the Fermi LAT First Source Catalog to localize the sources, and the blind search analysis to find the pulsars. We analyze the results and discuss the effect ofmore » positional error and spin frequency on gamma-ray pulsar detections. Finally, we construct a formula to determine the sensitivity of the blind search and present a sensitivity map assuming a standard set of pulsar parameters. The results of this study can be applied to population studies and are useful in characterizing unidentified LAT sources.« less

Stormwater runoff characterized by GIS determined source areas and runoff volumes.

PubMed

Liu, Yang; Soonthornnonda, Puripus; Li, Jin; Christensen, Erik R

2011-02-01

Runoff coefficients are usually considered in isolation for each drainage area with resulting large uncertainties in the areas and coefficients. Accurate areas and coefficients are obtained here by optimizing runoff coefficients for characteristic Geographic Information Systems (GIS) subareas within each drainage area so that the resulting runoff coefficients of each drainage area are consistent with those obtained from runoff and rainfall volumes. Lack of fit can indicate that the ArcGIS information is inaccurate or more likely, that the drainage area needs adjustment. Results for 18 drainage areas in Milwaukee, WI for 2000-2004 indicate runoff coefficients ranging from 0.123 for a mostly residential area to 0.679 for a freeway-related land, with a standard error of 0.047. Optimized runoff coefficients are necessary input parameters for monitoring, and for the analysis and design of in situ stormwater unit operations and processes for the control of both urban runoff quantity and quality.

40 CFR 419.37 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Pretreatment standards for new sources...) EFFLUENT GUIDELINES AND STANDARDS PETROLEUM REFINING POINT SOURCE CATEGORY Petrochemical Subcategory § 419.37 Pretreatment standards for new sources (PSNS). Except as provided in 40 CFR 403.7, any new source...

Avoid Ethical Misconduct in Manuscript Preparation.

PubMed

Hicks, Rodney W; Harris, Ruth

2016-01-01

In order for nurses and other health care professionals to make important contributions to the literature, there must be an awareness of the many areas where unintentional ethical conflicts can arise. Leading ethical concerns include plagiarism, duplicate submission, authorship standards, bias, and conflicts of interest. Although many sources are available on the variety of ethical concerns, this article takes the position to identify the area of concern and describe why it is an ethical violation. Solutions are posed for resolving the conflict, including why medical librarians can help in the publishing process.

Distributions of SO2 and NO2 in the lower atmosphere of an industrial area in Bhutan.

PubMed

Subba, Jas Raj; Thammakhet, Chongdee; Thavarungkul, Panote; Kanatharana, Proespichaya

2016-12-05

Two important air pollutants, sulfur dioxide (SO 2 ) and nitrogen dioxide (NO 2 ), were sampled and monitored in the spring season in the biggest industrial area of Bhutan. Field measurements of SO 2 and NO 2 were performed using standard colorimetric methods, and air samples were collected using an active sampling technique. Sampling sites were selected to cover all the potential catchment areas like settlements, staff quarters, shops and schools. The main objective of this sampling work was to see the distribution of these two pollutants from the source of emission (small scale industries) and to obtain and establish a baseline data. The active sampler was first tested and validated in a laboratory using liquid and gas standards of SO 2 and NO 2 . Good linearity from 0.050 to 1.0 µg mL -1 for SO 2 and from 0.010 to 1.0 µg mL -1 for NO 2 were obtained (R 2 > 0.99) with limits of detection of 30 and 50 ng mL -1 for SO 2 and NO 2 , respectively. Daylong sampling was done at selected sites with a range of distances away from the sources of emission. The ambient concentration of SO 2 and NO 2 were in the range of 0.45-4.46 and 0.56-5.68 µg m -3 , respectively.

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2013 CFR

2013-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2011 CFR

2011-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2012 CFR

2012-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2010 CFR

2010-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2014 CFR

2014-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

40 CFR 421.306 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... exceed the following values: (a) Chlorination off-gas wet air pollution control. PSNS for the Primary and... average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122 Nickel 0.515 0.346 Titanium 0.496 0.215 (b) Chlorination area-vent wet air pollution control. PSNS for...

40 CFR 421.306 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... exceed the following values: (a) Chlorination off-gas wet air pollution control. PSNS for the Primary and... average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122 Nickel 0.515 0.346 Titanium 0.496 0.215 (b) Chlorination area-vent wet air pollution control. PSNS for...

78 FR 27898 - Approval and Promulgation of State Implementation Plan Revisions; Infrastructure Requirements for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-13

... arithmetic mean PM 2.5 concentration from single or multiple community- oriented monitors, and 65 [mu]g/m\\3...-oriented monitor within an area. In addition, the 24-hour PM 10 standard was revised to be based on the...): Stationary source monitoring and reporting. 110(a)(2)(G): Emergency powers. 110(a)(2)(H): Future SIP...

75 FR 97 - Approval and Promulgation of Air Quality Implementation Plan: Kentucky; Approval Section 110(a)(1...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-04

... quality standard (NAAQS) through the year 2020. On July 15, 2009, the Commonwealth of Kentucky submitted... continued attainment and maintenance of the 1997 8-hour ozone NAAQS in the Paducah Area until 2020. As... source projections for 2011, 2014, 2017 and 2020 based on more recent data. Each of the section 110(a)(1...

Concentrations and Origins of Atmospheric Lead and Other Trace Species at a Rural Site in Northern China

NASA Technical Reports Server (NTRS)

Li, Can; Wen, Tianxue; Li, Zhanqing; Dickerson, Russell R.; Yang, Yongjie; Zhao, Yanan; Wang, Yuesi; Tsay, Si-Chee

2010-01-01

In this study we analyze the ambient levels of lead and other trace species in the bulk aerosol samples from a rural site approx.70 km ESE of Beijing in spring 2005. Lead (0.28+/-0.24 micro-g/cu m, average +/- standard deviation), along with several pollution \\related trace elements, was enriched by over 100 fold relative to the Earth's crust. The ambient lead levels showing large synoptic variations were well-correlated with other anthropogenic pollutants (e.g., CO and SO2). The Unmix receptor model resolved four factors in the aerosol composition data: a biomass burning source, an industrial and coal combustion source, a secondary aerosol source, and a dust source. The first three sources were strongest in weak southerly winds ahead of cold fronts, while the dust source peaked in strong northerly winds behind cold fronts. The second source, primarily representing emissions from industrial processes and relatively small \\scale coal burning such as in home and institutional heating, was identified as the main source of ambient lead in this study. Mobile sources might also contribute to this factor, but there was no distinct evidence of emissions due to combustion of leaded gasoline, despite a correlation between lead and CO. Potential source contribution function, calculated from backward trajectories and aerosol composition, further reveals that lead observed in this study was predominantly from the populated and industrialized areas to the south and SW of Xianghe, rather than Beijing to the west. Our results and several recent studies show that the lead levels in suburban areas near big cities in China, although generally lower than those in industrial districts and urban areas, are substantial (near or above 0.15 micro-g/cu m). More extensive studies on airborne lead and its emission sources in China are called for.

40 CFR 419.17 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Pretreatment standards for new sources...) EFFLUENT GUIDELINES AND STANDARDS PETROLEUM REFINING POINT SOURCE CATEGORY Topping Subcategory § 419.17 Pretreatment standards for new sources (PSNS). Except as provided in 40 CFR 403.7, any new source subject to...

40 CFR 419.27 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Pretreatment standards for new sources...) EFFLUENT GUIDELINES AND STANDARDS PETROLEUM REFINING POINT SOURCE CATEGORY Cracking Subcategory § 419.27 Pretreatment standards for new sources (PSNS). Except as provided in 40 CFR 403.7, any new source subject to...

40 CFR 419.47 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Pretreatment standards for new sources...) EFFLUENT GUIDELINES AND STANDARDS PETROLEUM REFINING POINT SOURCE CATEGORY Lube Subcategory § 419.47 Pretreatment standards for new sources (PSNS). Except as provided in 40 CFR 403.7, any new source subject to...

40 CFR 419.57 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Pretreatment standards for new sources...) EFFLUENT GUIDELINES AND STANDARDS PETROLEUM REFINING POINT SOURCE CATEGORY Integrated Subcategory § 419.57 Pretreatment standards for new sources (PSNS). Except as provided in 40 CFR 403.7, any new source subject to...

MOVES-Matrix and distributed computing for microscale line source dispersion analysis.

PubMed

Liu, Haobing; Xu, Xiaodan; Rodgers, Michael O; Xu, Yanzhi Ann; Guensler, Randall L

2017-07-01

MOVES and AERMOD are the U.S. Environmental Protection Agency's recommended models for use in project-level transportation conformity and hot-spot analysis. However, the structure and algorithms involved in running MOVES make analyses cumbersome and time-consuming. Likewise, the modeling setup process, including extensive data requirements and required input formats, in AERMOD lead to a high potential for analysis error in dispersion modeling. This study presents a distributed computing method for line source dispersion modeling that integrates MOVES-Matrix, a high-performance emission modeling tool, with the microscale dispersion models CALINE4 and AERMOD. MOVES-Matrix was prepared by iteratively running MOVES across all possible iterations of vehicle source-type, fuel, operating conditions, and environmental parameters to create a huge multi-dimensional emission rate lookup matrix. AERMOD and CALINE4 are connected with MOVES-Matrix in a distributed computing cluster using a series of Python scripts. This streamlined system built on MOVES-Matrix generates exactly the same emission rates and concentration results as using MOVES with AERMOD and CALINE4, but the approach is more than 200 times faster than using the MOVES graphical user interface. Because AERMOD requires detailed meteorological input, which is difficult to obtain, this study also recommends using CALINE4 as a screening tool for identifying the potential area that may exceed air quality standards before using AERMOD (and identifying areas that are exceedingly unlikely to exceed air quality standards). CALINE4 worst case method yields consistently higher concentration results than AERMOD for all comparisons in this paper, as expected given the nature of the meteorological data employed. The paper demonstrates a distributed computing method for line source dispersion modeling that integrates MOVES-Matrix with the CALINE4 and AERMOD. This streamlined system generates exactly the same emission rates and concentration results as traditional way to use MOVES with AERMOD and CALINE4, which are regulatory models approved by the U.S. EPA for conformity analysis, but the approach is more than 200 times faster than implementing the MOVES model. We highlighted the potentially significant benefit of using CALINE4 as screening tool for identifying potential area that may exceeds air quality standards before using AERMOD, which requires much more meteorology input than CALINE4.

Radiation and Health Technology Laboratory Capabilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bihl, Donald E.; Lynch, Timothy P.; Murphy, Mark K.

2005-07-09

The Radiological Standards and Calibrations Laboratory, a part of Pacific Northwest National Laboratory (PNNL)(a) performs calibrations and upholds reference standards necessary to maintain traceability to national standards. The facility supports U.S. Department of Energy (DOE) programs at the Hanford Site, programs sponsored by DOE Headquarters and other federal agencies, radiological protection programs at other DOE and commercial nuclear sites and research and characterization programs sponsored through the commercial sector. The laboratory is located in the 318 Building of the Hanford Site's 300 Area. The facility contains five major exposure rooms and several laboratories used for exposure work preparation, low-activity instrumentmore » calibrations, instrument performance evaluations, instrument maintenance, instrument design and fabrication work, thermoluminescent and radiochromic Dosimetry, and calibration of measurement and test equipment (M&TE). The major exposure facilities are a low-scatter room used for neutron and photon exposures, a source well room used for high-volume instrument calibration work, an x-ray facility used for energy response studies, a high-exposure facility used for high-rate photon calibration work, a beta standards laboratory used for beta energy response studies and beta reference calibrations and M&TE laboratories. Calibrations are routinely performed for personnel dosimeters, health physics instrumentation, photon and neutron transfer standards alpha, beta, and gamma field sources used throughout the Hanford Site, and a wide variety of M&TE. This report describes the standards and calibrations laboratory.« less

A global, open-source database of flood protection standards

NASA Astrophysics Data System (ADS)

Scussolini, Paolo; Aerts, Jeroen; Jongman, Brenden; Bouwer, Laurens; Winsemius, Hessel; de Moel, Hans; Ward, Philip

2016-04-01

Accurate flood risk estimation is pivotal in that it enables risk-informed policies in disaster risk reduction, as emphasized in the recent Sendai framework for Disaster Risk Reduction. To improve our understanding of flood risk, models are now capable to provide actionable risk information on the (sub)global scale. Still the accuracy of their results is greatly limited by the lack of information on standards of protection to flood that are actually in place; and researchers thus take large assumptions on the extent of protection. With our work we propose a first global, open-source database of FLOod PROtection Standards, FLOPROS, covering a range of spatial scales. FLOPROS is structured in three layers of information, and merges them into one consistent database: 1) the Design layer contains empirical information about the standard of protection presently in place; 2) the Policy layer contains intended protection standards from normative documents; 3) the Model layer uses a validated numerical approach to calculate protection standards for areas not covered in the other layers. The FLOPROS database can be used for more accurate risk assessment exercises across scales. As the database should be continually updated to reflect new interventions, we invite researchers and practitioners to contribute information. Further, we look for partners within the risk community to participate in additional strategies to implement the amount and accuracy of information contained in this first version of FLOPROS.

Eagle Ford Shale BTEX and NOx concentrations are dominated by oil and gas industry emissions

NASA Astrophysics Data System (ADS)

Schade, G. W.; Roest, G. S.

2017-12-01

US shale oil and gas exploration has been identified as a major source of greenhouse gases and non-methane hydrocarbon (NMHC) emissions to the atmosphere. Here, we present a detailed analysis of 2015 air quality data acquired by the Texas Commission on Environmental Quality (TCEQ) at an air quality monitoring station in Karnes County, TX, central to Texas' Eagle Ford shale area. Data include time series of hourly measured NMHCs, nitrogen oxides (NOx), and hydrogen sulfide (H2S) alongside meteorological measurements. The monitor was located in Karnes City, and thus affected by various anthropogenic emissions, including traffic and oil and gas exploration sources. Highest mixing ratios measured in 2015 included nearly 1 ppm ethane, 0.8 ppm propane, alongside 4 ppb benzene. A least-squares minimization non-negative matrix factorization (NMF) analysis, tested with prior data analyzed using standard PMF-2 software, showed six major emission sources: an evaporative and fugitive source, a flaring source, a traffic source, an oil field source, a diesel source, and an industrial manufacturing source, together accounting for more than 95% of data set variability, and interpreted using NMHC composition and meteorological data. Factor scores strongly suggest that NOx emissions are dominated by flaring and associated sources, such as diesel compressor engines, likely at midstream facilities, while traffic in this rural area is a minor NOx source. The results support, but exceed existing 2012 emission inventories estimating that local traffic emitted seven times fewer NOx than oil and gas exploration sources in the county. Sources of air toxics such as the BTEX compounds are also dominated by oil and gas exploration sources, but are more equally distributed between the associated factors. Benzene abundance is only 20-40% associated with traffic sources, and may thus be 2.5-5 times higher now than prior to the shale boom in this area. Although the monitor was located relatively far from oil and gas exploration sources, these results suggest that exposure to air toxics in this rural population has likely increased manifold since the start of the regional shale boom in 2008.

76 FR 52737 - Oil and Natural Gas Sector: New Source Performance Standards and National Emission Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-23

...This action announces how the EPA proposes to address the reviews of the new source performance standards for volatile organic compound and sulfur dioxide emissions from natural gas processing plants. We are proposing to add to the source category list any oil and gas operation not covered by the current listing. This action also includes proposed amendments to the existing new source performance standards for volatile organic compounds from natural gas processing plants and proposed standards for operations that are not covered by the existing new source performance standards. In addition, this action proposes how the EPA will address the residual risk and technology review conducted for the oil and natural gas production and natural gas transmission and storage national emission standards for hazardous air pollutants. This action further proposes standards for emission sources within these two source categories that are not currently addressed, as well as amendments to improve aspects of these national emission standards for hazardous air pollutants related to applicability and implementation. Finally, this action addresses provisions in these new source performance standards and national emission standards for hazardous air pollutants related to emissions during periods of startup, shutdown and malfunction.

Modelling of the estimated contributions of different sub-watersheds and sources to phosphorous export and loading from the Dongting Lake watershed, China.

PubMed

Hou, Ying; Chen, Weiping; Liao, Yuehua; Luo, Yueping

2017-11-03

Considerable growth in the economy and population of the Dongting Lake watershed in Southern China has increased phosphorus loading to the lake and resulted in a growing risk of lake eutrophication. This study aimed to reveal the spatial pattern and sources of phosphorus export and loading from the watershed. We applied an export coefficient model and the Dillon-Rigler model to quantify contributions of different sub-watersheds and sources to the total phosphorus (TP) export and loading in 2010. Together, the upper and lower reaches of the Xiang River watershed and the Dongting Lake Area contributed 60.9% of the TP exported from the entire watershed. Livestock husbandry appeared to be the largest anthropogenic source of TP, contributing more than 50% of the TP exported from each secondary sub-watersheds. The actual TP loading to the lake in 2010 was 62.9% more than the permissible annual TP loading for compliance with the Class III water quality standard for lakes. Three primary sub-watersheds-the Dongting Lake Area, the Xiang River, and the Yuan River watersheds-contributed 91.2% of the total TP loading. As the largest contributor among all sources, livestock husbandry contributed nearly 50% of the TP loading from the Dongting Lake Area and more than 60% from each of the other primary sub-watersheds. This study provides a methodology to identify the key sources and locations of TP export and loading in large lake watersheds. The study can provide a reference for the decision-making for controlling P pollution in the Dongting Lake watershed.

Coarse and fine aerosol source apportionment in Rio de Janeiro, Brazil

NASA Astrophysics Data System (ADS)

Godoy, Maria Luiza D. P.; Godoy, José Marcus; Roldão, Luiz Alfredo; Soluri, Daniela S.; Donagemma, Raquel A.

The metropolitan area of Rio de Janeiro is one of the twenty biggest urban agglomerations in the world, with 11 million inhabitants in the metropolitan area, and has a high population density, with 1700 hab. km -2. For this aerosol source apportionment study, the atmospheric aerosol sampling was performed at ten sites distributed in different locations of the metropolitan area from September/2003 to December/2005, with sampling during 24 h on a weekly basis. Stacked filter units (SFU) were used to collect fine and coarse aerosol particles with a flow rate of 17 L min -1. In both size fractions trace elements were analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) as well as water-soluble species by Ion-Chromatography (IC). Also gravimetric analysis and reflectance measurements provided aerosol mass and black carbon concentrations. Very good detection limits for up to 42 species were obtained. Mean annual PM 10 mass concentration ranged from 20 to 37 μg m -3, values that are within the Brazilian air quality standards. Receptor models such as principal factor analysis, cluster analysis and absolute principal factor analysis were applied in order to identify and quantify the aerosol sources. For fine and coarse modes, circa of 100% of the measured mass was quantitatively apportioned to relatively few identified aerosol sources. A very similar and consistent source apportionment was obtained for both fine and coarse modes for all 10 sampling sites. Soil dust is an important component, accounting for 22-72% and for 25-48% of the coarse and fine mass respectively. On the other hand, anthropogenic sources as vehicle traffic and oil combustion represent a relatively high contribution (52-75%) of the fine aerosol mass. The joint use of ICP-MS and IC analysis of species in aerosols has proven to be reliable and feasible for the analysis of large amount of samples, and the coupling with receptor models provided an excellent method for quantitative aerosol source apportionment in large urban areas.

Examining the influence of urban definition when assessing relative safety of drinking-water in Nigeria.

PubMed

Christenson, Elizabeth; Bain, Robert; Wright, Jim; Aondoakaa, Stephen; Hossain, Rifat; Bartram, Jamie

2014-08-15

Reducing inequalities is a priority from a human rights perspective and in water and public health initiatives. There are periodic calls for differential national and global standards for rural and urban areas, often justified by the suggestion that, for a given water source type, safety is worse in urban areas. For instance, initially proposed post-2015 water targets included classifying urban but not rural protected dug wells as unimproved. The objectives of this study were to: (i) examine the influence of urban extent definition on water safety in Nigeria, (ii) compare the frequency of thermotolerant coliform (TTC) contamination and prevalence of sanitary risks between rural and urban water sources of a given type and (iii) investigate differences in exposure to contaminated drinking-water in rural and urban areas. We use spatially referenced data from a Nigerian national randomized sample survey of five improved water source types to assess the extent of any disparities in urban-rural safety. We combined the survey data on TTC and sanitary risk with map layers depicting urban versus rural areas according to eight urban definitions. When examining water safety separately for each improved source type, we found no significant urban-rural differences in TTC contamination and sanitary risk for groundwater sources (boreholes and protected dug wells) and inconclusive findings for piped water and stored water. However, when improved and unimproved source types were combined, TTC contamination was 1.6 to 2.3 times more likely in rural compared to urban water sources depending on the urban definition. Our results suggest that different targets for urban and rural water safety are not justified and that rural dwellers are more exposed to unsafe water than urban dwellers. Additionally, urban-rural analyses should assess multiple definitions or indicators of urban to assess robustness of findings and to characterize a gradient that disaggregates the urban-rural dichotomy. Copyright © 2014 Elsevier B.V. All rights reserved.

Implementation of New Source Review in Areas that will be Designated as Nonattainment for the New 8-Hour Ozone Standard

EPA Pesticide Factsheets

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

40 CFR 415.176 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Pretreatment standards for new sources...) EFFLUENT GUIDELINES AND STANDARDS INORGANIC CHEMICALS MANUFACTURING POINT SOURCE CATEGORY Sodium Dichromate and Sodium Sulfate Production Subcategory § 415.176 Pretreatment standards for new sources (PSNS...

40 CFR 429.145 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Particleboard Manufacturing Subcategory § 429.145 Pretreatment standards for existing sources (PSES). Any existing source...

40 CFR 417.84 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.84 Pretreatment standards for existing sources. Any existing source...

40 CFR 417.84 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.84 Pretreatment standards for existing sources. Any existing source...

40 CFR 417.84 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.84 Pretreatment standards for existing sources. Any existing source...

40 CFR 417.84 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.84 Pretreatment standards for existing sources. Any existing source...

40 CFR 417.84 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.84 Pretreatment standards for existing sources. Any existing source...

Spectral study of the HESS J1745-290 gamma-ray source as dark matter signal

NASA Astrophysics Data System (ADS)

Cembranos, J. A. R.; Gammaldi, V.; Maroto, A. L.

2013-04-01

We study the main spectral features of the gamma-ray fluxes observed by the High Energy Stereoscopic System (HESS) from the J1745-290 Galactic Center source during the years 2004, 2005 and 2006. In particular, we show that these data are well fitted as the secondary gamma-rays photons generated from dark matter annihilating into Standard Model particles in combination with a simple power law background. We present explicit analyses for annihilation in a single standard model particle-antiparticle pair. In this case, the best fits are obtained for the uū and dbar d quark channels and for the W+W- and ZZ gauge bosons, with background spectral index compatible with the Fermi-Large Area Telescope (LAT) data from the same region. The fits return a heavy WIMP, with a mass above ~ 10 TeV, but well below the unitarity limit for thermal relic annihilation.

Detection of the Nitrate Pollution Sources in Shallow Aquifer, Using Integration of RS&GIS with Stable Isotopes Technologies

NASA Astrophysics Data System (ADS)

Shakak, N. B. I.

2018-04-01

Geographical information system (GIS) and remote sensing technique is a tool which is used for acquiring data from space, storing, analyzing and displaying spatial data, also can use for investigating source of environmental pollution which is affect health. Sudan landsat mosaic image which acquired in 2013 was used in this study to develop land use and land cover maps for tow selected study area, Khartoum urban area, and Bara locality in North kordofan state western Sudan. The main objective to assess the source of Nitrate pollution in shallow aquifer. ERDAS software was used to create land cover-land use maps for the study areas. For Khartoum town we used land sat mosaic image which acquire in 2013, and used supervised classification which more closely controlled than unsupervised. In this process, we select pixel that represent patterns you recognized or can identify with help from knowledge of the data, the classes desired, and the algorithm to be used is required. In this paper we integrated the (GIS&RS), and stable isotopes methods for fingerprinting Nitrate sources in shallow boreholes. The global positioning system (GPS), used in the field to identify the shallow boreholes location in a three dimensional coordinate (Latitude, longitude, and altitude), Water samples were collected from 19 shallow boreholes in the study areas according to the standard sampling method send to laboratory to measure stable nitrogen (δ15Nnitrate), and Nitrate-oxygen (δ18Onitrate) isotopes. Analysis were conducted by using isotope ratio mass spectrometry (IRMS). We can conclude that, special distribution and integration of GIs & RS help to identify the source of nitrate pollution.

[Distribution Characteristics and Source of Fluoride in Groundwater in Lower Plain Area of North China Plain: A Case Study in Nanpi County].

PubMed

Kong, Xiao-le; Wang, Shi-qin; Zhao, Huan; Yuan, Rui-qiang

2015-11-01

There is an obvious regional contradiction between water resources and agricultural produce in lower plain area of North China, however, excessive fluorine in deep groundwater further limits the use of regional water resources. In order to understand the spatial distribution characteristics and source of F(-) in groundwater, study was carried out in Nanpi County by field survey and sampling, hydrogeochemical analysis and stable isotopes methods. The results showed that the center of low fluoride concentrations of shallow groundwater was located around reservoir of Dalang Lake, and centers of high fluoride concentrations were located in southeast and southwest of the study area. The region with high fluoride concentration was consistent with the over-exploitation region of deep groundwater. Point source pollution of subsurface drainage and non-point source of irrigation with deep groundwater in some regions were the main causes for the increasing F(-) concentrations of shallow groundwater in parts of the sampling sites. Rock deposition and hydrogeology conditions were the main causes for the high F(-) concentrations (1.00 mg x L(-1), threshold of drinking water quality standard in China) in deep groundwater. F(-) released from clay minerals into the water increased the F(-) concentrations in deep groundwater because of over-exploitation. With the increasing exploitation and utilization of brackish shallow groundwater and the compressing and restricting of deep groundwater exploitation, the water environment in the middle and east lower plain area of North China will undergo significant change, and it is important to identify the distribution and source of F(-) in surface water and groundwater for reasonable development and use of water resources in future.

40 CFR 429.146 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Particleboard Manufacturing Subcategory § 429.146 Pretreatment standards for new sources (PSNS). Any new source subject to...

40 CFR 411.26 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS CEMENT MANUFACTURING POINT SOURCE CATEGORY Leaching Subcategory § 411.26 Pretreatment standards for new sources. Any new source subject to this subpart that introduces process...

40 CFR 455.25 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false New source performance standards (NSPS... GUIDELINES AND STANDARDS (CONTINUED) PESTICIDE CHEMICALS Organic Pesticide Chemicals Manufacturing Subcategory § 455.25 New source performance standards (NSPS). (a) Any new source subject to this subpart which...

40 CFR 421.66 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 CFR part 403 and achieve the following pretreatment standards for new sources. The mass of... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Pretreatment standards for new sources... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Copper Subcategory...

40 CFR 463.14 - New source performance standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false New source performance standards. 463... GUIDELINES AND STANDARDS (CONTINUED) PLASTICS MOLDING AND FORMING POINT SOURCE CATEGORY Contact Cooling and Heating Water Subcategory § 463.14 New source performance standards. (a) NSPS for bis(2-ethylhexyl...

40 CFR 455.25 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false New source performance standards (NSPS... GUIDELINES AND STANDARDS PESTICIDE CHEMICALS Organic Pesticide Chemicals Manufacturing Subcategory § 455.25 New source performance standards (NSPS). (a) Any new source subject to this subpart which discharges...

40 CFR 465.15 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... CFR part 403 and achieve the following pretreatment standards for new sources. The mass of wastewater... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Pretreatment standards for new sources... GUIDELINES AND STANDARDS (CONTINUED) COIL COATING POINT SOURCE CATEGORY Steel Basis Material Subcategory...

40 CFR 465.25 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 CFR part 403 and achieve the following pretreatment standards for new sources. The mass of... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Pretreatment standards for new sources... GUIDELINES AND STANDARDS (CONTINUED) COIL COATING POINT SOURCE CATEGORY Galvanized Basis Material Subcategory...

40 CFR 465.35 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 CFR part 403 and achieve the following pretreatment standards for new sources. The mass of... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Pretreatment standards for new sources... GUIDELINES AND STANDARDS (CONTINUED) COIL COATING POINT SOURCE CATEGORY Aluminum Basis Material Subcategory...

40 CFR 427.86 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GUIDELINES AND STANDARDS (CONTINUED) ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Coating or Finishing of Asbestos Textiles Subcategory § 427.86 Pretreatment standards for new sources. Any new source subject to...

40 CFR 427.86 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GUIDELINES AND STANDARDS (CONTINUED) ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Coating or Finishing of Asbestos Textiles Subcategory § 427.86 Pretreatment standards for new sources. Any new source subject to...

40 CFR 427.86 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GUIDELINES AND STANDARDS (CONTINUED) ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Coating or Finishing of Asbestos Textiles Subcategory § 427.86 Pretreatment standards for new sources. Any new source subject to...

40 CFR 417.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Soap Manufacturing by Fatty Acid Neutralization Subcategory § 417.36 Pretreatment standards for new sources. Any new source subject...

40 CFR 407.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS CANNED AND PRESERVED FRUITS AND VEGETABLES PROCESSING POINT SOURCE CATEGORY Canned and Preserved Vegetables Subcategory § 407.76 Pretreatment standards for new sources. Any new source...

40 CFR 407.66 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS CANNED AND PRESERVED FRUITS AND VEGETABLES PROCESSING POINT SOURCE CATEGORY Canned and Preserved Fruits Subcategory § 407.66 Pretreatment standards for new sources. Any new source...

40 CFR 417.74 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.74 Pretreatment standards for existing sources. Any existing source subject to...

40 CFR 417.74 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.74 Pretreatment standards for existing sources. Any existing source subject to...

40 CFR 417.74 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.74 Pretreatment standards for existing sources. Any existing source subject to...

40 CFR 417.74 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.74 Pretreatment standards for existing sources. Any existing source subject to...

40 CFR 417.74 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.74 Pretreatment standards for existing sources. Any existing source subject to...

40 CFR 447.15 - Standards of performance for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) INK FORMULATING POINT SOURCE CATEGORY Oil-Base Solvent Wash Ink Subcategory § 447.15 Standards of performance for new sources. The following standards of...

40 CFR 447.15 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) INK FORMULATING POINT SOURCE CATEGORY Oil-Base Solvent Wash Ink Subcategory § 447.15 Standards of performance for new sources. The following standards of...

40 CFR 447.15 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) INK FORMULATING POINT SOURCE CATEGORY Oil-Base Solvent Wash Ink Subcategory § 447.15 Standards of performance for new sources. The following standards of...

40 CFR 427.85 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Coating or Finishing of Asbestos Textiles Subcategory § 427.85 Standards of performance for new sources. The following standards of...

40 CFR 417.75 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.75 Standards of performance for new sources. The following standards of...

40 CFR 417.85 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.85 Standards of performance for new sources. The following standards of...

40 CFR 417.75 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.75 Standards of performance for new sources. The following standards of...

40 CFR 417.85 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.85 Standards of performance for new sources. The following standards of...

40 CFR 417.85 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.85 Standards of performance for new sources. The following standards of...

40 CFR 417.85 - Standards of performance for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.85 Standards of performance for new sources. The following standards of...

40 CFR 417.85 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.85 Standards of performance for new sources. The following standards of...

40 CFR 417.75 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.75 Standards of performance for new sources. The following standards of...

40 CFR 417.75 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.75 Standards of performance for new sources. The following standards of...

40 CFR 417.75 - Standards of performance for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Bar Soaps Subcategory § 417.75 Standards of performance for new sources. The following standards of...

40 CFR 446.15 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) PAINT FORMULATING POINT SOURCE CATEGORY Oil-Base Solvent Wash Paint Subcategory § 446.15 Standards of performance for new sources. The following standards of...

40 CFR 446.15 - Standards of performance for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) PAINT FORMULATING POINT SOURCE CATEGORY Oil-Base Solvent Wash Paint Subcategory § 446.15 Standards of performance for new sources. The following standards of...

40 CFR 446.15 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) PAINT FORMULATING POINT SOURCE CATEGORY Oil-Base Solvent Wash Paint Subcategory § 446.15 Standards of performance for new sources. The following standards of...

40 CFR 443.16 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... AND PRETREATMENT STANDARDS FOR NEW SOURCES FOR THE PAVING AND ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Emulsion Subcategory § 443.16 Pretreatment standards for new sources. Any...

40 CFR 443.36 - Pretreatment standard for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... AND PRETREATMENT STANDARDS FOR NEW SOURCES FOR THE PAVING AND ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Roofing Subcategory § 443.36 Pretreatment standard for new sources. Any...

40 CFR 443.36 - Pretreatment standard for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AND PRETREATMENT STANDARDS FOR NEW SOURCES FOR THE PAVING AND ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Roofing Subcategory § 443.36 Pretreatment standard for new sources. Any...

40 CFR 443.26 - Pretreatment standard for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... AND PRETREATMENT STANDARDS FOR NEW SOURCES FOR THE PAVING AND ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Concrete Subcategory § 443.26 Pretreatment standard for new sources. Any...

40 CFR 443.16 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AND PRETREATMENT STANDARDS FOR NEW SOURCES FOR THE PAVING AND ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Emulsion Subcategory § 443.16 Pretreatment standards for new sources. Any...

40 CFR 443.26 - Pretreatment standard for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AND PRETREATMENT STANDARDS FOR NEW SOURCES FOR THE PAVING AND ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Concrete Subcategory § 443.26 Pretreatment standard for new sources. Any...

40 CFR 421.194 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Standards of performance for new... Subcategory § 421.194 Standards of performance for new sources. Any new source subject to this subpart shall achieve the following new source performance standards: (a) Displacement Supernatant. NSPS for the...

40 CFR 421.204 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Subcategory § 421.204 Standards of performance for new sources. Any new source subject to this subpart shall achieve the following new source performance standards: (a) Spent battery electrolyte. NSPS for the... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Standards of performance for new...

40 CFR 421.254 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 29 2014-07-01 2012-07-01 true Standards of performance for new... Metals and Mercury Subcategory § 421.254 Standards of performance for new sources. Any new source subject to this subpart shall achieve the following new source performance standards: (a) Smelter wet air...

40 CFR 421.54 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Standards of performance for new... Electrolytic Copper Refining Subcategory § 421.54 Standards of performance for new sources. Any new source subject to this subpart shall achieve the following new source performance standards: (a) Subpart E...

40 CFR 421.54 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Standards of performance for new... Electrolytic Copper Refining Subcategory § 421.54 Standards of performance for new sources. Any new source subject to this subpart shall achieve the following new source performance standards: (a) Subpart E...

40 CFR 421.254 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Standards of performance for new... Metals and Mercury Subcategory § 421.254 Standards of performance for new sources. Any new source subject to this subpart shall achieve the following new source performance standards: (a) Smelter wet air...

40 CFR 421.194 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 29 2014-07-01 2012-07-01 true Standards of performance for new... Subcategory § 421.194 Standards of performance for new sources. Any new source subject to this subpart shall achieve the following new source performance standards: (a) Displacement Supernatant. NSPS for the...