Stretch-and-release fabrication, testing and optimization of a flexible ceramic armor inspired from fish scales.

PubMed

Martini, Roberto; Barthelat, Francois

2016-10-13

Protective systems that are simultaneously hard to puncture and compliant in flexion are desirable, but difficult to achieve because hard materials are usually stiff. However, we can overcome this conflicting design requirement by combining plates of a hard material with a softer substrate, and a strategy which is widely found in natural armors such as fish scales or osteoderms. Man-made segmented armors have a long history, but their systematic implementation in a modern and a protective system is still hampered by a limited understanding of the mechanics and the design of optimization guidelines, and by challenges in cost-efficient manufacturing. This study addresses these limitations with a flexible bioinspired armor based on overlapping ceramic scales. The fabrication combines laser engraving and a stretch-and-release method which allows for fine tuning of the size and overlap of the scales, and which is suitable for large scale fabrication. Compared to a continuous layer of uniform ceramic, our fish-scale like armor is not only more flexible, but it is also more resistant to puncture and more damage tolerant. The proposed armor is also about ten times more puncture resistant than soft elastomers, making it a very attractive alternative to traditional protective equipment.

Tanks in the Street: Lessons Learned Through Bytes not Blood

DTIC Science & Technology

2001-02-02

under armor protection. The crews relied on the vehicle’s vision blocks and sights to acquire targets. The simulation replicated these actions that...maintain mutually supporting fires. There is a delicate balance between remaining mobile and remaining under armor protection. A small force, squad

Full Spectrum LAR

DTIC Science & Technology

2008-01-01

Emerson 901 TOW Under Armor (TUA) weapons system. When reliably operational, the Emerson 901 turret can still provide effective anti-armor fires as...the rear of the LAV-R thus there is no available space to carry ammunition resupplies, food, or under armor ambulance kits. On the other hand, the...the LAR battalion; however, the LAV-EFSS cannot be fired under armor protection or in the direct firing mode. Both the LAV-120 AMS and the LAV-EFSS

Guidelines for design, installation, and maintenance of a waterproof wearing surface for timber bridge decks

Treesearch

Richard E. Weyers; Joseph R. Loferski; J. Daniel Dolan; John E. Haramis; Joseph H. Howard; Lola Hislop

2001-01-01

To enhance long-term timber bridge performance, timber material must be protected from moisture. Wearing surfaces made of asphalt pavement with and without a waterproof membrane have been used to provide protection from moisture on timber decks. This type of wearing surface also protects the deck from other damage while providing a smooth, skid-resistant surface....

Advanced Metallic Thermal Protection System Development

NASA Technical Reports Server (NTRS)

Blosser, M. L.; Chen, R. R.; Schmidt, I. H.; Dorsey, J. T.; Poteet, C. C.; Bird, R. K.

2002-01-01

A new Adaptable, Robust, Metallic, Operable, Reusable (ARMOR) thermal protection system (TPS) concept has been designed, analyzed, and fabricated. In addition to the inherent tailorable robustness of metallic TPS, ARMOR TPS offers improved features based on lessons learned from previous metallic TPS development efforts. A specific location on a single-stage-to-orbit reusable launch vehicle was selected to develop loads and requirements needed to design prototype ARMOR TPS panels. The design loads include ascent and entry heating rate histories, pressures, acoustics, and accelerations. Additional TPS design issues were identified and discussed. An iterative sizing procedure was used to size the ARMOR TPS panels for thermal and structural loads as part of an integrated TPS/cryogenic tank structural wall. The TPS panels were sized to maintain acceptable temperatures on the underlying structure and to operate under the design structural loading. Detailed creep analyses were also performed on critical components of the ARMOR TPS panels. A lightweight, thermally compliant TPS support system (TPSS) was designed to connect the TPS to the cryogenic tank structure. Four 18-inch-square ARMOR TPS panels were fabricated. Details of the fabrication process are presented. Details of the TPSS for connecting the ARMOR TPS panels to the externally stiffened cryogenic tank structure are also described. Test plans for the fabricated hardware are presented.

Armored garment for protecting

DOEpatents

Purvis, James W [Albuquerque, NM; Jones, II, Jack F.; Whinery, Larry D [Albuquerque, NM; Brazfield, Richard [Albuquerque, NM; Lawrie, Catherine [Tijeras, NM; Lawrie, David [Tijeras, NM; Preece, Dale S [Watkins, CO

2009-08-11

A lightweight, armored protective garment for protecting an arm or leg from blast superheated gases, blast overpressure shock, shrapnel, and spall from a explosive device, such as a Rocket Propelled Grenade (RPG) or a roadside Improvised Explosive Device (IED). The garment has a ballistic sleeve made of a ballistic fabric, such as an aramid fiber (e.g., KEVLAR.RTM.) cloth, that prevents thermal burns from the blast superheated gases, while providing some protection from fragments. Additionally, the garment has two or more rigid armor inserts that cover the upper and lower arm and protect against high-velocity projectiles, shrapnel and spall. The rigid inserts can be made of multiple plies of a carbon/epoxy composite laminate. The combination of 6 layers of KEVLAR.RTM. fabric and 28 plies of carbon/epoxy laminate inserts (with the inserts being sandwiched in-between the KEVLAR.RTM. layers), can meet the level IIIA fragmentation minimum V.sub.50 requirements for the US Interceptor Outer Tactical Vest.

Novel Synthesis and Characterization of Inorganic Fullerene Type WS2 and Graphene Hybrids

DTIC Science & Technology

2013-03-01

Figure 1.   Photograph of two sailors wearing a “light” version of body armor (Image used with permission from LT Melanie Chambers and LT Kathryn...protection body armor in use is a vast improvement over the animal hides and chain mail our descendants wore many years ago [1]. Today’s body armor...worn, but lowers the level of threats the body armor will be able to withstand. Often such operating environments force soldiers to choose between

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, Paul A.; Cooper, Candice Frances; Burnett, Damon J.

Light body armor development for the warfighter is based on trial-and-error testing of prototype designs against ballistic projectiles. Torso armor testing against blast is virtually nonexistent but necessary to ensure adequate protection against injury to the heart and lungs. In this report, we discuss the development of a high-fidelity human torso model, it's merging with the existing Sandia Human Head-Neck Model, and development of the modeling & simulation (M&S) capabilities necessary to simulate wound injury scenarios. Using the new Sandia Human Torso Model, we demonstrate the advantage of virtual simulation in the investigation of wound injury as it relates tomore » the warfighter experience. We present the results of virtual simulations of blast loading and ballistic projectile impact to the tors o with and without notional protective armor. In this manner, we demonstrate the ad vantages of applying a modeling and simulation approach to the investigation of wound injury and relative merit assessments of protective body armor without the need for trial-and-error testing.« less

An Illustrative Case Study for Twentieth Century Defense Planners: The Technology and Politics of United States Coastal Defense, 1880-1898.

DTIC Science & Technology

1980-04-24

plunging fire on the armored decks of attacking ships. Some inventors and technicians would propose increased use of submarine mines and torpedoes for...and mines , see "The Defense of Our Sea-Ports," Harper’s Weekly 71 (November 1885): 928-930 and the "Endicott Report," p. 97; for the Navy’s role, see...urgently re- quired, the character and kind of defenses best adapted for each, with reference to armament [and] the utilization of torpedoes, mines

Superelement Analysis of Tile-Reinforced Composite Armor

NASA Technical Reports Server (NTRS)

Davila, Carlos G.

1998-01-01

Super-elements can greatly improve the computational efficiency of analyses of tile-reinforced structures such as the hull of the Composite Armored Vehicle. By taking advantage of the periodicity in this type of construction, super-elements can be used to simplify the task of modeling, to virtually eliminate the time required to assemble the stiffness matrices, and to reduce significantly the analysis solution time. Furthermore, super-elements are fully transferable between analyses and analysts, so that they provide a consistent method to share information and reduce duplication. This paper describes a methodology that was developed to model and analyze large upper hull components of the Composite Armored Vehicle. The analyses are based on two types of superelement models. The first type is based on element-layering, which consists of modeling a laminate by using several layers of shell elements constrained together with compatibility equations. Element layering is used to ensure the proper transverse shear deformation in the laminate rubber layer. The second type of model uses three-dimensional elements. Since no graphical pre-processor currently supports super-elements, a special technique based on master-elements was developed. Master-elements are representations of super-elements that are used in conjunction with a custom translator to write the superelement connectivities as input decks for ABAQUS.

Use of armored RNA as a standard to construct a calibration curve for real-time RT-PCR.

PubMed

Donia, D; Divizia, M; Pana', A

2005-06-01

Armored Enterovirus RNA was used to standardize a real-time reverse transcription (RT)-PCR for environmental testing. Armored technology is a system to produce a robust and stable RNA standard, trapped into phage proteins, to be used as internal control. The Armored Enterovirus RNA protected sequence includes 263 bp of highly conserved sequences in 5' UTR region. During these tests, Armored RNA has been used to produce a calibration curve, comparing three different fluorogenic chemistry: TaqMan system, Syber Green I and Lux-primers. The effective evaluation of three amplifying commercial reagent kits, in use to carry out real-time RT-PCR, and several extraction procedures of protected viral RNA have been carried out. The highest Armored RNA recovery was obtained by heat treatment while chemical extraction may decrease the quantity of RNA. The best sensitivity and specificity was obtained using the Syber Green I technique since it is a reproducible test, easy to use and the cheapest one. TaqMan and Lux-primer assays provide good RT-PCR efficiency in relationship to the several extraction methods used, since labelled probe or primer request in these chemistry strategies, increases the cost of testing.

29 CFR 782.4 - Drivers' helpers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... definition has classified all such employees, including armed guards on armored trucks and conductorettes on..., although the primary duty of armed guards on armored trucks is to protect the valuables in the case of...

29 CFR 782.4 - Drivers' helpers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... definition has classified all such employees, including armed guards on armored trucks and conductorettes on..., although the primary duty of armed guards on armored trucks is to protect the valuables in the case of...

29 CFR 782.4 - Drivers' helpers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... definition has classified all such employees, including armed guards on armored trucks and conductorettes on..., although the primary duty of armed guards on armored trucks is to protect the valuables in the case of...

3D-printing a 'family' of biomimetic models to explain armored grasping in syngnathid fishes.

PubMed

Porter, Michael M; Ravikumar, Nakul

2017-11-06

Seahorses and pipehorses evolved at least two independent strategies for tail grasping, despite being armored with a heavy body plating. To help explain mechanical trade-offs associated with the different designs, we created a 'family' of 3D-printed models that mimic variations in the presence and size of their armored plates. We measured the performance of the biomimetic proxies across several mechanical metrics, representative of their protective and prehensile capacities. Our results show that the models mimicking the tails of seahorses are the best all-around performers, while those of the distal-most, prehensile region of pipehorses are more flexible, but less protected. The comparison also reveals that different adaptive strategies provide different task-specific performance advantages, which could be leveraged for the design of armored manipulators or other bio-inspired technologies.

33 CFR 149.419 - Can the water supply for the helicopter deck fire protection system be part of a fire water system?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Can the water supply for the... § 149.419 Can the water supply for the helicopter deck fire protection system be part of a fire water system? (a) The water supply for the helicopter deck fire protection system required under § 149.420 or...

Department of the Army Justification of Estimates for Fiscal Year 1983 Submitted to Congress February 1982. Part 3 (Weapons & Tracked Combat Vehicles).

DTIC Science & Technology

1982-02-01

of 130 kits for the Fire Support Teem Vehicle, an integrated system platform which will provide under - armor protection for the ground laser locator...procureuent of 495 kits for the Fire Support Team Vehicles, an integrated system platform which will provide under - armor protection for the Ground Laser

Field investigation of the corrosion protection performance of bridge decks and piles constructed with epoxy-coated reinforcing steel in Virginia.

DOT National Transportation Integrated Search

1997-10-01

The corrosion protection performance of epoxy-coated reinforcing steel (ECR) was assessed in three bridge decks and the piles : in three marine structures in Virginia in 1996. The decks were 17 years old, two of the marine structures were 8 years old...

A new nonpenetrating ballistic injury.

PubMed

Carroll, A W; Soderstrom, C A

1978-12-01

A new, nonpenetrating ballistic injury mechanism involving individuals protected by soft body armor is described. Experimental studies using laboratory animals have demonstrated that despite stopping missile penetration, the heart, liver, spleen, and spinal cord are vulnerable to injury. The rapid jolting force of an impacting bullet is contrasted with the usually encountered mechanisms producing blunt trauma injury. The experimental methodology used to assess a 20% increase in survival probability and an 80% decrease in the need for surgical intervention with a new soft body armor is reviewed. Five cases of ballistic assaults on law enforcement personnel protected by soft body armor are presented. Four emphasize the potentially lifesaving qualities of the armor, while the fifth indicates the need for torso encircling design. Hospitalization should follow all assaults, regardless of the innocuous appearance of the skin lesion and the apparent well being on the assaulted individual. Therapeutic guidelines for patient management are suggested.

A new nonpenetrating ballistic injury.

PubMed Central

Carroll, A W; Soderstrom, C A

1978-01-01

A new, nonpenetrating ballistic injury mechanism involving individuals protected by soft body armor is described. Experimental studies using laboratory animals have demonstrated that despite stopping missile penetration, the heart, liver, spleen, and spinal cord are vulnerable to injury. The rapid jolting force of an impacting bullet is contrasted with the usually encountered mechanisms producing blunt trauma injury. The experimental methodology used to assess a 20% increase in survival probability and an 80% decrease in the need for surgical intervention with a new soft body armor is reviewed. Five cases of ballistic assaults on law enforcement personnel protected by soft body armor are presented. Four emphasize the potentially lifesaving qualities of the armor, while the fifth indicates the need for torso encircling design. Hospitalization should follow all assaults, regardless of the innocuous appearance of the skin lesion and the apparent well being on the assaulted individual. Therapeutic guidelines for patient management are suggested. Images Fig. 1. Fig. 2. Fig. 3. PMID:736653

Collaborative Point Paper on Active Protection Systems

DTIC Science & Technology

2006-10-01

for the Hunter VHP CIED Program. Also, General Dynamics Armament and Technical Products (GDATP), Burlington, VT is contracted by the Marine Corps...the incoming threat at a relatively long distance. Specific details about the composition and mechanism of this explosive interceptor device are...relatively thin shell of ballistic steel and composite armor, also known as hybrid armor, designed to provide optimal protection from specific threats

A slotted cathodic protection system for bridge decks.

DOT National Transportation Integrated Search

1985-01-01

A non-overlay, slotted cathodic protection system was installed two years ago on a concrete bridge deck in Virginia. The design, installation, and operation of this system are fairly straightforward. A protective current density of 1.6 mA/ft (17 mA...

Shock imprint and rolling direction influence upon the breaking tenacity for 2P armor steel

NASA Astrophysics Data System (ADS)

Zichil, V.; Coseru, A.; Schnakovszky, C.; Herghelegiu, E.; Radu, C.

2016-08-01

The state of art in present literature shows that the breaking tenacity of a material is influenced by the integrity of the structure. Since armors used in aviation and to protect military vehicles are frequently impact loaded, through the contact between armor sheet and projectiles, or other foreign bodies, the authors have proposed to study the dependence between the breaking tenacity of 2P armor steel depending on the direction of the rolling of the armor plate, of the geometry (spherical imprint, pyramidal and linear imprint) and the depth of the deformation that results after impact. Tests were conducted upon CT (ASTM E- 399) specimen type, using the critical factor of stress intensity during the state of planar strain.

The protection effectiveness of waterproof membrane systems on bridge decks in Louisiana : final report.

DOT National Transportation Integrated Search

1978-12-01

The effects of de-icing salts on concrete and reinforcing steel is well documented, and efficient methods of protection from the penetrating chloride ions have long been sought. Concrete bridge decks need the protection, and waterproofing the concret...

46 CFR 132.320 - Helicopter-landing decks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Helicopter-landing decks. 132.320 Section 132.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS FIRE-PROTECTION EQUIPMENT Miscellaneous § 132.320 Helicopter-landing decks. Each vessel with a helicopter-landing deck must...

46 CFR 132.320 - Helicopter-landing decks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Helicopter-landing decks. 132.320 Section 132.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS FIRE-PROTECTION EQUIPMENT Miscellaneous § 132.320 Helicopter-landing decks. Each vessel with a helicopter-landing deck must...

46 CFR 132.320 - Helicopter-landing decks.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Helicopter-landing decks. 132.320 Section 132.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS FIRE-PROTECTION EQUIPMENT Miscellaneous § 132.320 Helicopter-landing decks. Each vessel with a helicopter-landing deck must...

46 CFR 132.320 - Helicopter-landing decks.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Helicopter-landing decks. 132.320 Section 132.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS FIRE-PROTECTION EQUIPMENT Miscellaneous § 132.320 Helicopter-landing decks. Each vessel with a helicopter-landing deck must...

46 CFR 132.320 - Helicopter-landing decks.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Helicopter-landing decks. 132.320 Section 132.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS FIRE-PROTECTION EQUIPMENT Miscellaneous § 132.320 Helicopter-landing decks. Each vessel with a helicopter-landing deck must...

Compartment A125; view forward of barbette, an armored cylinder for ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Compartment A-125; view forward of barbette, an armored cylinder for supporting and protecting the forward 8" gun turret above. Anchor windlass is in left background. (033) - USS Olympia, Penn's Landing, 211 South Columbus Boulevard, Philadelphia, Philadelphia County, PA

Spacecraft ceramic protective shield

NASA Technical Reports Server (NTRS)

Larriva, Rene F. (Inventor); Nelson, Anne (M.); Czechanski, James G. (Inventor); Poff, Ray E. (Inventor)

1995-01-01

A low areal density protective shield apparatus, and method for making same, for protecting spacecraft structures from impact with hypervelocity objects, including a bumper member comprising a bumper ceramic layer, a bumper shock attenuator layer, and a bumper confining layer. The bumper ceramic layer can be SiC or B.sub.4 C; the bumper shock attenuator layer can be zirconia felt; and the bumper confining layer can be aluminum. A base armor member can be spaced from the bumper member and a ceramic fiber-based curtain can be positioned between the bumper and base armor members.

Protective ability of the standard U.S. Military Personal Armor System, Ground Troops (PASGT) fragmentation vest against common small arms projectiles.

PubMed

Roberts, G K; Bullian, M E

1993-08-01

This study analyzes the ballistic protection provided by the standard U.S. Military Personal Armor System, Ground Troops fragmentation vest against threats from handgun and shotgun projectiles. Damage assessment was conducted using 10% ordnance gelatin, a tissue simulant which has been proven to have a close correlation with living tissue. The standard fragmentation vest was shown to provide protection from commonly encountered handgun bullets and shotgun pellets, but not from shotgun slugs or center-fire rifle bullets.

46 CFR 108.486 - Helicopter decks.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Helicopter decks. 108.486 Section 108.486 Shipping COAST... Fire Extinguishing Systems Fire Protection for Helicopter Facilities § 108.486 Helicopter decks. At least two of the accesses to the helicopter landing deck must each have a fire hydrant on the unit's...

46 CFR 108.486 - Helicopter decks.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Helicopter decks. 108.486 Section 108.486 Shipping COAST... Fire Extinguishing Systems Fire Protection for Helicopter Facilities § 108.486 Helicopter decks. At least two of the accesses to the helicopter landing deck must each have a fire hydrant on the unit's...

46 CFR 108.486 - Helicopter decks.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Helicopter decks. 108.486 Section 108.486 Shipping COAST... Fire Extinguishing Systems Fire Protection for Helicopter Facilities § 108.486 Helicopter decks. At least two of the accesses to the helicopter landing deck must each have a fire hydrant on the unit's...

46 CFR 108.486 - Helicopter decks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Helicopter decks. 108.486 Section 108.486 Shipping COAST... Fire Extinguishing Systems Fire Protection for Helicopter Facilities § 108.486 Helicopter decks. At least two of the accesses to the helicopter landing deck must each have a fire hydrant on the unit's...

46 CFR 108.486 - Helicopter decks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Helicopter decks. 108.486 Section 108.486 Shipping COAST... Fire Extinguishing Systems Fire Protection for Helicopter Facilities § 108.486 Helicopter decks. At least two of the accesses to the helicopter landing deck must each have a fire hydrant on the unit's...

WARFIGHTER SUPPORT: Independent Expert Assessment of Army Body Armor Test Results and Procedures Needed Before Fielding

DTIC Science & Technology

2009-10-01

protective vest and ceramic plate inserts. GAO observed Preliminary Design Model testing of new plate designs, which resulted in the Army’s...Table 1: Organizations Contacted for Information about Body Armor Testing 46 Figures Figure 1: ESAPI Plates as Worn inside Outer Tactical Vest 11...Central Command has required that DOD personnel in its area of operations be issued the Interceptor Body Armor system, comprising ceramic plates that

40 CFR Table 28 to Subpart G of... - Deck Seam Length Factors a (SD) for Internal Floating Roof Tanks

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 9 2011-07-01 2011-07-01 false Deck Seam Length Factors a (SD) for... (SD) for Internal Floating Roof Tanks Deck construction Typical deck seam length factor Continuous... decks only. Units for SD are feet per square feet. b SD=1/W, where W = sheet width (feet). c If no...

40 CFR Table 28 to Subpart G of... - Deck Seam Length Factors a (SD) for Internal Floating Roof Tanks

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Deck Seam Length Factors a (SD) for... (SD) for Internal Floating Roof Tanks Deck construction Typical deck seam length factor Continuous... decks only. Units for SD are feet per square feet. b SD=1/W, where W = sheet width (feet). c If no...

A behavioral analysis of eye protection use by soldiers.

PubMed

Wong, T Y; Seet, B

1997-11-01

One of the major problems faced by eye injury prevention programs in the military is the low compliance among individual soldiers with eye armor use. We use three different health behavioral models (the health belief model, the social learning theory, and the PRECEDE model) to analyze and explore the various factors involved in the use of eye armor. Some of the factors that appear to be important in affecting the behavior include environmental conditions (e.g., actual military deployment versus nondeployment activity), organizational attitude toward eye protection programs, community influence, individual knowledge and perception of eye injury, and belief in the efficacy of eye armor. An understanding of these factors can help influence the development of more effective strategies for eye injury prevention in the military.

Enzyme Armoring by an Organosilica Layer: Synthesis and Characterization of Hybrid Organic/Inorganic Nanobiocatalysts.

PubMed

Correro, M Rita; Sykora, Sabine; Corvini, Philippe F-X; Shahgaldian, Patrick

2017-01-01

The availability of highly stable and reusable enzymes is one of the main challenges in bio-based industrial processes. Enzyme immobilization and encapsulation represent promising strategies to reach this goal. In this chapter, the synthetic strategy to produce hybrid organic/inorganic nanobiocatalysts (NBC) is reported. This strategy is based on the sequential immobilization of an enzyme on the surface of silica nanoparticles followed by the growth, at the surface of the nanoparticles, of a shielding layer which serves as an armor to protect the enzyme against denaturation/degradation. This armor is produced through a thickness-controlled organosilane poly-condensation onto the nanoparticle surface around the enzyme to form a protective organosilica layer. The armored nanobiocatalysts present enhanced catalytic activity and improved stability against heat, pH, chaotropic agents, proteases, and ultrasound. The method is versatile in that it can be successfully adapted to a number of different enzymes. © 2017 Elsevier Inc. All rights reserved.

Black Pineleaf Scale (FIDL)

Treesearch

Katharine A. Sheehan; Mario A. Melendez; Shana Westfall

1998-01-01

The black pineleaf scale (Nuculaspis californica (Coleman)) belongs to a group of sucking insects called armored scales. Concealed under their protective shells, these scales insert their mouthparts into their hosts, removing sap and, possibly, injecting toxic enzymes secreted in the saliva. Armored scales are important pests of agricultural and ornamental plants;...

Reasons to Improve: The Evolution of the U.S. Tank from 1945-1991

DTIC Science & Technology

2010-05-01

comparable to German Panther and Tiger tanks in armor and firepower. The Korean War experience did two things. First, it ushered in the era of limited war...yards away.21 In July 1943, a Tiger tank near Gela, Sicily quickly destroyed four tanks and hit a fifth from G Company, 67th Armored Regiment.22 During...German adversary in the form of Panther and Tiger tanks retained a significant advantage over the U.S. Sherman tank because of its armored protection

Ballistic Performance of Alimina/S-2 Glass-Reinforced Polymer-Matrix Composite Hybrid Lightweight Armor Against Armor Piercing (AP) and Non-AP Projectiles

DTIC Science & Technology

2007-01-01

and a phenolic -resin based polymeric matrix. Such armor panels offer superior protection against fragmented ballistic threats when compared to...database does not contain a material model for the HJ1 composite but provides a model for a Kevlar Fiber Reinforced Polymer (KFRP) containing 53 vol... phenolic resin and epoxy yield stresses and then with a ratio of the S-2 glass and aramid fibers volume fractions. To test the validity of the

Technical Reference Manual: NATO Planning Guide for the Estimation of Chemical, Biological, Radiological, and Nuclear (CBRN), Casualties, Allied Medical Publication-8(C)

DTIC Science & Technology

2010-08-01

use of these submodels was reached. The details of the four agent-specific meetings, including the dates , locations, and participating SMEs are...Protected Armored Personnel Carrier – Closed 0% 0% Armored Personnel Carrier – Moving 50% 0% Armored Personnel Carrier – Open 100% 0% Earth Shelter 75...limited number of radioisotopes , typically emitting gamma and/or beta radiation. RDDs include at least two types of radiation sources: 1) point

Medical Provider Ballistic Protection at Active Shooter Events.

PubMed

Stopyra, Jason P; Bozeman, William P; Callaway, David W; Winslow, James; McGinnis, Henderson D; Sempsrott, Justin; Evans-Taylor, Lisa; Alson, Roy L

2016-01-01

There is some controversy about whether ballistic protective equipment (body armor) is required for medical responders who may be called to respond to active shooter mass casualty incidents. In this article, we describe the ongoing evolution of recommendations to optimize medical care to injured victims at such an incident. We propose that body armor is not mandatory for medical responders participating in a rapid-response capacity, in keeping with the Hartford Consensus and Arlington Rescue Task Force models. However, we acknowledge that the development and implementation of these programs may benefit from the availability of such equipment as one component of risk mitigation. Many police agencies regularly retire body armor on a defined time schedule before the end of its effective service life. Coordination with law enforcement may allow such retired body armor to be available to other public safety agencies, such as fire and emergency medical services, providing some degree of ballistic protection to medical responders at little or no cost during the rare mass casualty incident. To provide visual demonstration of this concept, we tested three "retired" ballistic vests with ages ranging from 6 to 27 years. The vests were shot at close range using police-issue 9mm, .40 caliber, .45 caliber, and 12-gauge shotgun rounds. Photographs demonstrate that the vests maintained their ballistic protection and defeated all of these rounds. 2016.

Composite structural armor for combat vehicle applications

NASA Technical Reports Server (NTRS)

Haskell, William E., III; Alesi, A. L.; Parsons, G. R.

1990-01-01

Several projects that have demonstrated the advantages of using thick composite armor technology for structural applications in armored combat vehicles are discussed. The first involved composite cargo doors for the Marine Corps LVTP-7 amphibious landing vehicle. Another was a demonstration composite turret that offered a weight reduction of 15.5 percent. The advantages of this composite armor compared to metallic armors used for combat vehicle hull and turret applications are reduced weight at equal ballistic protection; reduced back armor spall; excellent corrosion resistance; reduced production costs by parts consolidation; and inherent thermal and acoustic insulative properties. Based on the encouraging results of these past programs, the Demonstration Composite Hull Program was started in September 1986. To demonstrate this composite armor technology, the Army's newest infantry fighting vehicle, the Bradley Fighting Vehicle (BFV), was selected as a model. A composite infantry fighting vehicle, designated the CIFV for this program, has been designed and fabricated and is currently undergoing a 6000 mile field endurance test. The CIFV demonstration vehicle uses the BFV engine, transmission, suspension, track and other equipment.

Styrene-butadiene latex modifiers for bridge deck overlay concrete.

DOT National Transportation Integrated Search

1978-04-01

Styrene-butadiene (S/B) latex modified concrete overlays are being used to protect : new bridge decks from rapid deicer-borne chloride intrusion and also in bridge : deck rehabilitation efforts. The purposes of this research were to evaluate several ...

Mosaic Transparent Armor System Final Report CRADA No. TC02162.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuntz, J. D.; Breslin, M.

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and The Protective Group, Inc. (TPG) to improve the performance of the mosaic transparent armor system (MTAS) for transparent armor applications, military and civilian. LLNL was to provide the unique MTAS technology and designs to TPG for innovative construction and ballistic testing of improvements needed for current and near future application of the armor windows on vehicles and aircraft. The goal of the project was to advance the technology of MTAS to the point that these mosaic transparent windowsmore » would be introduced and commercially manufactured for military vehicles and aircraft.« less

Martian Surface at an Angle

NASA Technical Reports Server (NTRS)

2004-01-01

This latest color 'postcard from Mars,' taken on Sol 5 by the panoramic camera on the Mars Exploration Rover Spirit, looks to the north. The apparent slope of the horizon is due to the several-degree tilt of the lander deck. On the left, the circular topographic feature dubbed Sleepy Hollow can be seen along with dark markings that may be surface disturbances caused by the airbag-encased lander as it bounced and rolled to rest. A dust-coated airbag is prominent in the foreground, and a dune-like object that has piqued the interest of the science team with its dark, possibly armored top coating, can be seen on the right.

Membrane protection for steel stringer tops : Yaquina Bay Bridge, Newport, Oregon : construction report.

DOT National Transportation Integrated Search

1980-10-01

The experimental feature of this project was to evaluate the application and performance of Chevron Industrial Membrane applied to the tops of steel deck stringers and other similar members as corrosion protection in conjunction with the deck replace...

Quantifying the effectiveness of shoreline armoring removal on coastal biota of Puget Sound.

PubMed

Lee, Timothy S; Toft, Jason D; Cordell, Jeffery R; Dethier, Megan N; Adams, Jeffrey W; Kelly, Ryan P

2018-01-01

Shoreline armoring is prevalent around the world with unprecedented human population growth and urbanization along coastal habitats. Armoring structures, such as riprap and bulkheads, that are built to prevent beach erosion and protect coastal infrastructure from storms and flooding can cause deterioration of habitats for migratory fish species, disrupt aquatic-terrestrial connectivity, and reduce overall coastal ecosystem health. Relative to armored shorelines, natural shorelines retain valuable habitats for macroinvertebrates and other coastal biota. One question is whether the impacts of armoring are reversible, allowing restoration via armoring removal and related actions of sediment nourishment and replanting of native riparian vegetation. Armoring removal is targeted as a viable option for restoring some habitat functions, but few assessments of coastal biota response exist. Here, we use opportunistic sampling of pre- and post-restoration data for five biotic measures (wrack % cover, saltmarsh % cover, number of logs, and macroinvertebrate abundance and richness) from a set of six restored sites in Puget Sound, WA, USA. This broad suite of ecosystem metrics responded strongly and positively to armor removal, and these results were evident after less than one year. Restoration responses remained positive and statistically significant across different shoreline elevations and temporal trajectories. This analysis shows that removing shoreline armoring is effective for restoration projects aimed at improving the health and productivity of coastal ecosystems, and these results may be widely applicable.

Quantifying the effectiveness of shoreline armoring removal on coastal biota of Puget Sound

PubMed Central

Toft, Jason D.; Adams, Jeffrey W.

2018-01-01

Shoreline armoring is prevalent around the world with unprecedented human population growth and urbanization along coastal habitats. Armoring structures, such as riprap and bulkheads, that are built to prevent beach erosion and protect coastal infrastructure from storms and flooding can cause deterioration of habitats for migratory fish species, disrupt aquatic–terrestrial connectivity, and reduce overall coastal ecosystem health. Relative to armored shorelines, natural shorelines retain valuable habitats for macroinvertebrates and other coastal biota. One question is whether the impacts of armoring are reversible, allowing restoration via armoring removal and related actions of sediment nourishment and replanting of native riparian vegetation. Armoring removal is targeted as a viable option for restoring some habitat functions, but few assessments of coastal biota response exist. Here, we use opportunistic sampling of pre- and post-restoration data for five biotic measures (wrack % cover, saltmarsh % cover, number of logs, and macroinvertebrate abundance and richness) from a set of six restored sites in Puget Sound, WA, USA. This broad suite of ecosystem metrics responded strongly and positively to armor removal, and these results were evident after less than one year. Restoration responses remained positive and statistically significant across different shoreline elevations and temporal trajectories. This analysis shows that removing shoreline armoring is effective for restoration projects aimed at improving the health and productivity of coastal ecosystems, and these results may be widely applicable. PMID:29492331

Repair and protection of hydraulic cement concrete bridge decks.

DOT National Transportation Integrated Search

1994-01-01

The report is an updated version of "A Manual for the Repair and Protection of Hydraulic Cement Concrete Bridge Decks" (VTRC 90-TAR2). The report was prepared for Chapter 2 of the Hydraulic Cement Concrete Construction School Study Guide which is dis...

Corrosion protection service life of epoxy-coated reinforcing steel in Virginia bridge decks.

DOT National Transportation Integrated Search

2003-01-01

The corrosion protection service life extension provided by epoxy-coated reinforcement (ECR) was determined by comparing ECR and bare steel bars from 10 Virginia bridge decks built between 1981 and 1995. The objective was to determine the corrosion p...

Internally sealed concrete for bridge deck protection : interim report no. 1.

DOT National Transportation Integrated Search

1978-01-01

The study reported here was performed to extend the body of knowledge concerning the use of internally sealed concrete to protect bridge deck reinforcing steel. A laboratory determination of the properties of the wax and concrete used and a field eva...

Protected by Design

ERIC Educational Resources Information Center

Beck, Darren

2012-01-01

Since Pen Argyl High School in Pen Argyl, Pennsylvania was in the process of redeveloping its mascot, the Green Knight, the author decided to implement a studio project based on armor. In groups of three, students would research an assigned type of historical armor, replicate it in cardboard, and fit it to a group member. The lesson had heavy…

Characterizing the interaction among bullet, body armor, and human and surrogate targets.

PubMed

Shen, Weixin; Niu, Yuqing; Bykanova, Lucy; Laurence, Peter; Link, Norman

2010-12-01

This study used a combined experimental and modeling approach to characterize and quantify the interaction among bullet, body armor, and human surrogate targets during the 10-1000 μs range that is crucial to evaluating the protective effectiveness of body armor against blunt injuries. Ballistic tests incorporating high-speed flash X-ray measurements were performed to acquire the deformations of bullets and body armor samples placed against ballistic clay and gelatin targets with images taken between 10 μs and 1 ms of the initial impact. Finite element models (FEMs) of bullet, armor, and gelatin and clay targets were developed with material parameters selected to best fit model calculations to the test measurements. FEMs of bullet and armor interactions were then assembled with a FEM of a human torso and FEMs of clay and gelatin blocks in the shape of a human torso to examine the effects of target material and geometry on the interaction. Test and simulation results revealed three distinct loading phases during the interaction. In the first phase, the bullet was significantly slowed in about 60 μs as it transferred a major portion of its energy into the body armor. In the second phase, fibers inside the armor were pulled toward the point of impact and kept on absorbing energy until about 100 μs after the initial impact when energy absorption reached its peak. In the third phase, the deformation on the armor's back face continued to grow and energies inside both armor and targets redistributed through wave propagation. The results indicated that armor deformation and energy absorption in the second and third phases were significantly affected by the material properties (density and stiffness) and geometrical characteristics (curvature and gap at the armor-target interface) of the targets. Valid surrogate targets for testing the ballistic resistance of the armor need to account for these factors and produce the same armor deformation and energy absorption as on a human torso until at least about 100 μs (maximum armor energy absorption) or more preferably 300 μs (maximum armor deformation).

Effects of concrete moisture on polymer overlay bond over new concrete.

DOT National Transportation Integrated Search

2015-06-01

Epoxy polymer overlays have been used for decades on existing bridge decks to protect the deck and extend its : service life. The polymer overlays ability to seal a bridge deck is now being specified for new construction. Questions exist : about t...

Cathodic protection of two concrete bridge decks using titanium-mesh anodes : interim report.

DOT National Transportation Integrated Search

1991-01-01

Expanded titanium mesh with a layer of precious metal oxides sintered around it has recently been introduced to fulfill the need for a durable anode in the cathodic protection (CP) of concrete bridge decks. In addition to being resistant to chemical ...

Effects of concrete moisture on polymer overlay bond over new concrete : [technical summary].

DOT National Transportation Integrated Search

2015-06-01

Epoxy polymer overlays have been used for decades on existing bridge decks to protect : the deck and extend its service life. The polymer overlays ability to seal a bridge deck : is now being specified for new construction. Questions exist about t...

46 CFR 108.133 - Hull superstructure, structural bulkheads, decks, and deckhouses.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Hull superstructure, structural bulkheads, decks, and deckhouses. 108.133 Section 108.133 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A... Protection § 108.133 Hull superstructure, structural bulkheads, decks, and deckhouses. Each hull...

46 CFR 108.133 - Hull superstructure, structural bulkheads, decks, and deckhouses.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Hull superstructure, structural bulkheads, decks, and deckhouses. 108.133 Section 108.133 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A... Protection § 108.133 Hull superstructure, structural bulkheads, decks, and deckhouses. Each hull...

46 CFR 108.133 - Hull superstructure, structural bulkheads, decks, and deckhouses.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Hull superstructure, structural bulkheads, decks, and deckhouses. 108.133 Section 108.133 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A... Protection § 108.133 Hull superstructure, structural bulkheads, decks, and deckhouses. Each hull...

Optimization of armored spherical tanks for storage on the lunar surface

NASA Technical Reports Server (NTRS)

Bents, D. J.; Knight, D. A.

1992-01-01

A redundancy strategy for reducing micrometeroid armoring mass is investigated, with application to cryogenic reactant storage for a regenerative fuel cell (RFC) on the lunar surface. In that micrometeoroid environment, the cryogenic fuel must be protected from loss due to tank puncture. The tankage must have a sufficiently high probability of survival over the length of the mission so that the probability of system failure due to tank puncture is low compared to the other mission risk factors. Assuming that a single meteoroid penetration can cause a storage tank to lose its contents, two means are available to raise the probability of surviving micrometeoroid attack to the desired level. One can armor the tanks to a thickness sufficient to reduce probability of penetration of any tank to the desired level or add extra capacity in the form of spare tanks that results in survival of a given number out of the ensemble at the desired level. A combination of these strategies (armoring and redundancy) is investigated. The objective is to find the optimum combination which yields the lowest shielding mass per cubic meter of surviving fuel out of the original ensemble. The investigation found that, for the volumes of fuel associated with multikilowatt class cryo storage RFC's, and the armoring methodology and meteoroid models used, storage should be fragmented into small individual tanks. Larger installations (more fuel) pay less of a shielding penalty than small installations. For the same survival probability over the same time period, larger volumes will require less armoring mass per unit volume protected.

76 FR 16353 - International Traffic in Arms Regulations: Exemption for Temporary Export of Chemical Agent...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-23

... removing certain extraneous language that does not change the meaning of the exemption. DATES: The... need to wear body armor or chemical agent protective gear for personal safety. In August 2009, the ITAR was amended to provide an exemption for the temporary export of body armor covered by 22 CFR 121.1...

Dynamic Deformation of a Ceramic/GRP Composite From KE Impact

DTIC Science & Technology

1996-01-01

to guarantee the protection of the crew of an armored vehicle or the electronic equipment behind the armor. Since there is only very little data...HALSTEAD SEVEN OAKS KENT TN14 7BP UNITED KINGDOM 1 BAlTELiE INGENIEURTECHNIK GMBH AlTN W FUCKE DUESSELDORFLER STR 9 D 65760 ESCHBORN GERMANY 1 5 1

Engines/Fuels Workshop, 6-8 December 1982, San Antonio, Texas.

DTIC Science & Technology

1982-01-01

occupies approximately 40% of cooled diesels of exclusive military design and the under - armor hull volume. Of that, only a use. The second is the range of...be placed largely,or better yet, exelusively under armor *: protection. Thus, the more fuel needed for a , • • ’ v’ v• i given range requirement, the

State-of-the-art report on rapid repair techniques for bridge decks.

DOT National Transportation Integrated Search

1990-01-01

Bridges that are candidates for rapid repair techniques have peak-hour traffic volumes that are so high that it is not practical to close a lane to repair the deck or to install a deck protection system except during off-peak traffic periods. This re...

46 CFR 108.135 - Boundary bulkheads, decks of galleys, and combustible material lockers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... material lockers. 108.135 Section 108.135 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Protection § 108.135 Boundary bulkheads, decks of galleys, and combustible material lockers. Each boundary... storage locker must be an A class bulkhead and A class deck respectively. ...

46 CFR 108.135 - Boundary bulkheads, decks of galleys, and combustible material lockers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... material lockers. 108.135 Section 108.135 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Protection § 108.135 Boundary bulkheads, decks of galleys, and combustible material lockers. Each boundary... storage locker must be an A class bulkhead and A class deck respectively. ...

46 CFR 108.135 - Boundary bulkheads, decks of galleys, and combustible material lockers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... material lockers. 108.135 Section 108.135 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Protection § 108.135 Boundary bulkheads, decks of galleys, and combustible material lockers. Each boundary... storage locker must be an A class bulkhead and A class deck respectively. ...

46 CFR 108.135 - Boundary bulkheads, decks of galleys, and combustible material lockers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... material lockers. 108.135 Section 108.135 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Protection § 108.135 Boundary bulkheads, decks of galleys, and combustible material lockers. Each boundary... storage locker must be an A class bulkhead and A class deck respectively. ...

46 CFR 108.135 - Boundary bulkheads, decks of galleys, and combustible material lockers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... material lockers. 108.135 Section 108.135 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Protection § 108.135 Boundary bulkheads, decks of galleys, and combustible material lockers. Each boundary... storage locker must be an A class bulkhead and A class deck respectively. ...

Effect of bank protection measures, Stehekin River, Chelan County, Washington

USGS Publications Warehouse

Nelson, L.M.

1986-01-01

An investigation of the lower Stehekin River was conducted to study the effects on flood elevations and velocities from four bank protection and flood prevention measures that are being contemplated as a means of reducing erosional losses of river bank property. These measures are: bank armoring, armored revetment levees, spur dikes, and redevelopment of old cutoff channels. The banks at seven study sites could be armored without adverse effect on the flood velocities and elevations. The largest increases due to armoring--up to 1.6 ft/sec in velocity and 1 ft in elevation--occurred in the vicinity of sites 5, 6, and 7 where the gradient of the river channel is about 50 ft/mi and the velocities are high to begin with (about 6 to 13 ft/sec). The use of a levee in conjunction with armoring on the northeast bank from sites 5 to 7 would increase the velocities as much as 2.8 ft/sec and increase the elevation as much as 1 ft, but it would also provide some flood protection to the east bank, which is frequently inundated. Spur dikes were considered a practical alternative only at site 3, where reduced bank erosion may occur without aggravating flood inundation or erosion elsewhere. The rerouting of flood flow through an old cutoff channel near site 1 increased the velocity by 3.2 ft/sec and the elevation by 1 ft for the 100-year flood; however, it would move floodwater away from residential property where bank erosion is a problem. The few other old channels that shortcut river bends where much erosion occurs are apparently already part of the channel during floods. (Author 's abstract)

Protection mechanisms of the iron-plated armor of a deep-sea hydrothermal vent gastropod

PubMed Central

Yao, Haimin; Dao, Ming; Imholt, Timothy; Huang, Jamie; Wheeler, Kevin; Bonilla, Alejandro; Suresh, Subra; Ortiz, Christine

2010-01-01

Biological exoskeletons, in particular those with unusually robust and multifunctional properties, hold enormous potential for the development of improved load-bearing and protective engineering materials. Here, we report new materials and mechanical design principles of the iron-plated multilayered structure of the natural armor of Crysomallon squamiferum, a recently discovered gastropod mollusc from the Kairei Indian hydrothermal vent field, which is unlike any other known natural or synthetic engineered armor. We have determined through nanoscale experiments and computational simulations of a predatory attack that the specific combination of different materials, microstructures, interfacial geometries, gradation, and layering are advantageous for penetration resistance, energy dissipation, mitigation of fracture and crack arrest, reduction of back deflections, and resistance to bending and tensile loads. The structure-property-performance relationships described are expected to be of technological interest for a variety of civilian and defense applications. PMID:20133823

NDE of hybrid armor structures using acoustography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandhu, Jaswinder S.; Pergantis, Charles G.

2011-06-23

The US Army is investigating the use of composite materials to deliver lightweight and more effective armor protection systems to soldiers and other army assets. However, widespread use of such hybrid armor will require a reliable but fast NDE methodology to ensure integrity of these components during manufacturing and while in service. Traditional ultrasonic inspection of such hybrid armor structures may prove to be very effective, but point-by-point ultrasonic scanning is inherently time-consuming and manufacturing slowdowns could develop in high-volume production of such armor systems. In this paper, we report on the application of acoustography for the NDE of hybridmore » armor structures. Acoustography differs from conventional ultrasonic testing in that test objects are inspected in full field, analogously to real time x-ray imaging. The approach uses a novel, super high resolution large area acousto-optic (AO) sensor, which allows image formation through simple ultrasound shadow casting, analogous to x-ray image formation. This NDE approach offers significant inspection speed advantage over conventional point-by-point ultrasonic scanning procedures and is well-suited for high volume production. We will report initial results on a number of hybrid armor plate specimens employing composite materials that are being investigated by the US Army. Acoustography NDE results will also be verified using other complimentary NDE methods.« less

Aircraft Armor an Empirical Approach to the Efficient Design of Armor for Aircraft

DTIC Science & Technology

1944-01-31

weighted) to projectile corn diameter (e]_/d) equals 0.6 or less, the use of duralumin will produce the maximum protection per unit weight employed, and...pr.’tection (as represented by the curves for different striking validities) may be obtained from a lower value ox («l/d COB 6), c:re efficient use

Development of a Meso-Scale Material Model for Ballistic Fabric and Its Use in Flexible-Armor Protection Systems

DTIC Science & Technology

2010-02-01

s mobility. Early materials used included leather , silk, metal chain mail, and metal plates. Replacement of metal with a nylon (poly-amide) fabric...tests of flexible-fabric armor, and as shown by Tan et al. (Ref 24) in a series of postimpact fabric-inspection studies, play an important role in

Mitigation Systems for Confined Blast Loading - Crew Protection in Armored Vehicles

DTIC Science & Technology

2009-04-01

Effects of Tungsten Alloy Property Variations on Penetrator Performance for Spaced Armors.” Advances in Powder Metallurgy and Particulate Materials...Table 8.1. Cylinder properties for confined field test. ............................................... 93 Table 8.2. FEM snapshot of the confined...persons or property . Blast mitigation should reduce the overpressure, impulse, fragments, projectile, thermal and toxic hazards that occur during an

A comparative study of bio-inspired protective scales using 3D printing and mechanical testing.

PubMed

Martini, Roberto; Balit, Yanis; Barthelat, Francois

2017-06-01

Flexible natural armors from fish, alligators or armadillo are attracting an increasing amount of attention for their unique combinations of hardness, flexibility and light weight. The extreme contrast of stiffness between hard scales and surrounding soft tissues gives rise to unusual and attractive mechanisms, which now serve as models for the design of bio-inspired armors. Despite this growing interest, there is little guideline for the choice of materials, optimum thickness, size, shape and arrangement for the protective scales. In this work, we explore how the geometry and arrangement of hard scales can be tailored to promote scale-scale interactions. We use 3D printing to fabricate arrays of scales with increasingly complex geometries and arrangements, from simple squares with no overlap to complex ganoid-scales with overlaps and interlocking features. We performed puncture tests and flexural tests on each of the 3D printed materials, and we report the puncture resistance - compliance characteristics of each design on an Ashby chart. The interactions between the scales can significantly increase the resistance to puncture, and these interactions can be maximized by tuning the geometry and arrangement of the scales. Interestingly, the designs that offer the best combinations of puncture resistance and flexural compliance are similar to the geometry and arrangement of natural teleost and ganoid scales, which suggests that natural evolution has shaped these systems to maximize flexible protection. This study yields new insights into the mechanisms of natural dermal armor, and also suggests new designs for personal protective systems. Flexible natural armors from fishes, alligators or armadillos are attracting an increasing amount of attention for their unique and attractive combinations of hardness, flexibility and low weight. Despite a growing interest in bio-inspired flexible protection, there is still little guideline for the choice of materials, optimum thickness, size, shape and arrangement of the protective scales. In this work, we explore how the geometry and arrangement of hard scales affect puncture resistance and flexural compliance, using 3D printing and mechanical testing. Our main finding is that the performance of the scaled skin in terms of puncture resistance can be significantly improved by slight changes in their geometry and arrangement. Our results also suggest that natural evolution has shaped scaled skins to maximize flexible protection. This study yields new insights into the mechanics of natural dermal armors, and also suggests new designs for personal protective systems. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Protecting wood decks from biodegradation and weathering : evaluation of deck finish systems

Treesearch

J. J. Morrell; P. F. Schneider; R. Sam Williams

2001-01-01

Mildew resistance, water repellency, and overall finish appearance were evaluated for 32 deck finishes on western redcedar (Thuja plicata D. Donn.) and Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) after 12, 21, and 39 months of outdoor exposure in western Oregon. The finishes were either solvent-borne or waterborne; were ei- ther clear, tinted, or lightly...

The Impact of Armor on the Design, Utilization and Survivability of Ground Vehicles: The History of Armor Development and Use

DTIC Science & Technology

2012-09-01

control functions. Components that are included in this category include the steering column / linkages as well as brakes . D. FIREPOWER COMPONENTS...COMPONENTS: STEERING AND BRAKES ......................48 D. FIREPOWER COMPONENTS: TURRET AND ARMAMENT .............49 E. PROTECTION COMPONENTS: HULL AND...Key Functional Area Propulsion Powertrain (Engine / Transmission) Tracks / Wheels Control Steering Brakes / Suspension Firepower Turret Armament

Transparent Materials for Armor - A Cost Study

DTIC Science & Technology

2010-01-11

UNCLASSIFIED UNCLASSIFIED Example: M1114 Recent History 2006 “Iraqi Pope Glass” 2004-2005 GPK (Gunner Protection Kit) Early OIF Curb Wt: 10,300lbs GVW...12,100lbs More Vehicles More Attacks More Glass UNCLASSIFIED UNCLASSIFIED Future Transparent Gun Shields Requirement: Upgrade GPKs with transparent...Objective AHI GS & GPK Baseline Field Modified GS & APK UNCLASSIFIED UNCLASSIFIED •Average Total ($) for transparent armor increased by about 20% (each

Stability of hard plates on soft substrates and application to the design of bioinspired segmented armor

NASA Astrophysics Data System (ADS)

Martini, R.; Barthelat, F.

2016-07-01

Flexible natural armors from fish, alligators or armadillo are attracting an increasing amount of attention from their unique and attractive combinations of hardness, flexibility and light weight. In particular, the extreme contrast of stiffness between hard plates and surrounding soft tissues give rise to unusual and attractive mechanisms, which now serve as model for the design of bio-inspired armors. Despite a growing interest in bio-inspired flexible protection, there is little guidelines as to the choice of materials, optimum thickness, size, shape and arrangement for the protective plates. In this work, we focus on a failure mode we recently observed on natural and bio-inspired scaled armors: the unstable tilting of individual scales subjected to off-centered point forces. We first present a series of experiments on this system, followed by a model based on contact mechanics and friction. We condense the result into a single stability diagram which capture the key parameters that govern the onset of plate tilting from a localized force. We found that the stability of individual plates is governed by the location of the point force on the plate, by the friction at the surface of the plate, by the size of the plate and by the stiffness of the substrate. We finally discuss how some of these parameters can be optimized at the design stage to produce bio-inspired protective systems with desired combination of surface hardness, stability and flexural compliance.

Tough Textiles Protect Payloads and Public Safety Officers

NASA Technical Reports Server (NTRS)

2009-01-01

In order to create the Mars Pathfinder s mission-critical airbags in the 1990s, NASA s Jet Propulsion Laboratory collaborated with New Ipswich, New Hampshire s Warwick Mills Inc. to weave multi-layer textiles for the airbags for both Pathfinder and the Mars Exploration Rovers. Warwick Mills applied techniques from the collaboration to its puncture- and impact-resistant TurtleSkin product line. The company's metal flex armor (MFA) vests offer stab protection comparable with rigid steel plates and over 50,000 of the vests have sold. The SoftPlate body armor offers protection from handgun bullets, and like the MFA, is designed to be more comfortable than rigid vests. International public safety and military customers are now benefiting from the TurtleSkin products.

33 CFR 143.110 - Guards and rails.

Code of Federal Regulations, 2011 CFR

2011-07-01

... helicopter landing decks which are provided for in paragraph (b) of this section, and areas not normally... guard rail. (b) The unprotected perimeter of the helicopter landing deck shall be protected with a...

33 CFR 143.110 - Guards and rails.

Code of Federal Regulations, 2013 CFR

2013-07-01

... helicopter landing decks which are provided for in paragraph (b) of this section, and areas not normally... guard rail. (b) The unprotected perimeter of the helicopter landing deck shall be protected with a...

33 CFR 143.110 - Guards and rails.

Code of Federal Regulations, 2012 CFR

2012-07-01

... helicopter landing decks which are provided for in paragraph (b) of this section, and areas not normally... guard rail. (b) The unprotected perimeter of the helicopter landing deck shall be protected with a...

33 CFR 143.110 - Guards and rails.

Code of Federal Regulations, 2014 CFR

2014-07-01

... helicopter landing decks which are provided for in paragraph (b) of this section, and areas not normally... guard rail. (b) The unprotected perimeter of the helicopter landing deck shall be protected with a...

33 CFR 143.110 - Guards and rails.

Code of Federal Regulations, 2010 CFR

2010-07-01

... helicopter landing decks which are provided for in paragraph (b) of this section, and areas not normally... guard rail. (b) The unprotected perimeter of the helicopter landing deck shall be protected with a...

Ballistic Protection

DTIC Science & Technology

2011-06-14

ground vehicle Program Management (PM) needs. Base Armor • Small Arms/Frag Opaque B-kits • Medium Cal/Frag Opaque B-kits • Transparent Armor Appliqué...packaged/mounted on a vehicle -representative structure and after introducing relevant environments and relevant threat engagements. Yes 4 MIL-STD 810...Contamination by Fluids • Solar Radiation • Rain • Humidity • Salt Fog • Sand & Dust • Acidic Atmosphere • Vibration • Shock • Fire, Smoke & Toxicity ATPD

Puget Sound Shorelines and the Impacts of Armoring-Proceedings of a State of the Science Workshop, May 2009

USGS Publications Warehouse

Shipman, Hugh; Dethier, Megan N.; Gelfenbaum, Guy R.; Fresh, Kurt L.; Dinicola, Richard S.

2010-01-01

The widespread extent and continued construction of seawalls and bulkheads on Puget Sound's beaches has emerged as a significant issue in shoreline management and coastal restoration in the region. Concerns about the impacts of shoreline armoring and managing the potential risks to coastal property are in many ways similar to those in other places, but Puget Sound also poses unique challenges related to its sheltered setting, glacially formed geology, rich estuarine ecology, and historical development pattern. The effects of armoring on shorelines are complex, involving both physical and biological science and requiring consideration of the cumulative impacts of small-scale activities over large scales of space and time. In addition, the issue is controversial, as it often places strongly held private interests in protecting shoreline property against broad public mandates to preserve shorelines for public uses and to protect environmental resources. Communities making difficult decisions about regulating shoreline activities and prioritizing restoration projects need to be informed by the best science available. To address these issues, a scientific workshop was convened in May 2009, specifically to bring local and national experts together to review the state of the science regarding the physical and biological impacts of armoring on sheltered shorelines such as those of Puget Sound.

Development of a Meso-Scale Material Model for Ballistic Fabric and Its Use in Flexible-Armor Protection Systems

NASA Astrophysics Data System (ADS)

Grujicic, M.; Bell, W. C.; Arakere, G.; He, T.; Xie, X.; Cheeseman, B. A.

2010-02-01

A meso-scale ballistic material model for a prototypical plain-woven single-ply flexible armor is developed and implemented in a material user subroutine for the use in commercial explicit finite element programs. The main intent of the model is to attain computational efficiency when calculating the mechanical response of the multi-ply fabric-based flexible-armor material during its impact with various projectiles without significantly sacrificing the key physical aspects of the fabric microstructure, architecture, and behavior. To validate the new model, a comparative finite element method analysis is carried out in which: (a) the plain-woven single-ply fabric is modeled using conventional shell elements and weaving is done in an explicit manner by snaking the yarns through the fabric and (b) the fabric is treated as a planar continuum surface composed of conventional shell elements to which the new meso-scale unit-cell based material model is assigned. The results obtained show that the material model provides a reasonably good description for the fabric deformation and fracture behavior under different combinations of fixed and free boundary conditions. Finally, the model is used in an investigation of the ability of a multi-ply soft-body armor vest to protect the wearer from impact by a 9-mm round nose projectile. The effects of inter-ply friction, projectile/yarn friction, and the far-field boundary conditions are revealed and the results explained using simple wave mechanics principles, high-deformation rate material behavior, and the role of various energy-absorbing mechanisms in the fabric-based armor systems.

Aircraft Survivability: UAVs and Manned Aircraft - Increasing Effectiveness and Survivability, Fall 2002

DTIC Science & Technology

2002-01-01

techniques that interface with the composite structure to attach opaque armor(s) to compos- ite aircraft structure. Over a period of four years...2002 2. REPORT TYPE 3. DATES COVERED 00-00-2002 to 00-00-2002 4. TITLE AND SUBTITLE Aircraft Survivability: UAVs and Manned Aircraft ...survivability concepts to UAV program offices and airframe manufacturers. 11 Aircraft Fire Protection Techniques—Application to UAVs by Ms. Ginger Bennett

33 CFR 149.419 - Can the water supply for the helicopter deck fire protection system be part of a fire water system?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Can the water supply for the helicopter deck fire protection system be part of a fire water system? 149.419 Section 149.419 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: DESIGN, CONSTRUCTION, AND EQUIPMENT...

33 CFR 149.419 - Can the water supply for the helicopter deck fire protection system be part of a fire water system?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Can the water supply for the helicopter deck fire protection system be part of a fire water system? 149.419 Section 149.419 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: DESIGN, CONSTRUCTION, AND EQUIPMENT...

33 CFR 149.419 - Can the water supply for the helicopter deck fire protection system be part of a fire water system?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Can the water supply for the helicopter deck fire protection system be part of a fire water system? 149.419 Section 149.419 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: DESIGN, CONSTRUCTION, AND EQUIPMENT...

33 CFR 149.419 - Can the water supply for the helicopter deck fire protection system be part of a fire water system?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Can the water supply for the helicopter deck fire protection system be part of a fire water system? 149.419 Section 149.419 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: DESIGN, CONSTRUCTION, AND EQUIPMENT...

Internally sealed concrete for bridge deck protection : final report.

DOT National Transportation Integrated Search

1983-01-01

This study investigated the characteristics of internally sealed concrete through tests on specimens fabricated in the laboratory to determine its properties and an installation in a bridge deck to assess the controls needed during construction and i...

Evaluation of the Installation and Initial Condition of Rosphalt Overlays on Bridge Decks.

DOT National Transportation Integrated Search

2013-06-01

"Protection systems are placed on bridge decks to retard the intrusion of chlorides and moisture that can eventually cause : corrosion deterioration. The Virginia Department of Transportation typically uses hydraulic cement concrete (HCC) overlays of...

Field evaluations of waterproof membrane systems for bridge decks, 1972-1974.

DOT National Transportation Integrated Search

1975-01-01

Waterproof membrane systems are being studied by many agencies from the standpoint of their effectiveness in protecting the reinforcing steel in concrete bridge decks against corrosion. Trial applications and evaluations of six such systems, includin...

Fabrication, testing and modeling of a new flexible armor inspired from natural fish scales and osteoderms.

PubMed

Chintapalli, Ravi Kiran; Mirkhalaf, Mohammad; Dastjerdi, Ahmad Khayer; Barthelat, Francois

2014-09-01

Crocodiles, armadillo, turtles, fish and many other animal species have evolved flexible armored skins in the form of hard scales or osteoderms, which can be described as hard plates of finite size embedded in softer tissues. The individual hard segments provide protection from predators, while the relative motion of these segments provides the flexibility required for efficient locomotion. In this work, we duplicated these broad concepts in a bio-inspired segmented armor. Hexagonal segments of well-defined size and shape were carved within a thin glass plate using laser engraving. The engraved plate was then placed on a soft substrate which simulated soft tissues, and then punctured with a sharp needle mounted on a miniature loading stage. The resistance of our segmented armor was significantly higher when smaller hexagons were used, and our bio-inspired segmented glass displayed an increase in puncture resistance of up to 70% compared to a continuous plate of glass of the same thickness. Detailed structural analyses aided by finite elements revealed that this extraordinary improvement is due to the reduced span of individual segments, which decreases flexural stresses and delays fracture. This effect can however only be achieved if the plates are at least 1000 stiffer than the underlying substrate, which is the case for natural armor systems. Our bio-inspired system also displayed many of the attributes of natural armors: flexible, robust with 'multi-hit' capabilities. This new segmented glass therefore suggests interesting bio-inspired strategies and mechanisms which could be systematically exploited in high-performance flexible armors. This study also provides new insights and a better understanding of the mechanics of natural armors such as scales and osteoderms.

Galvanic cathodic protection for reinforced concrete bridge decks: Field evaluation

NASA Astrophysics Data System (ADS)

Whiting, D.; Stark, D.

1981-06-01

The application of four sacrificial zinc anode cathodic protection systems to a reinforced concrete highway bridge deck is described. Two system designs were found to be the most promising in terms of polarized potentials and protective current densities achieved during the 3 year monitoring program. One design uses commercially available zinc ribbon anodes spaced at 5 in (127 mm) centers; the other, custom-fabricated perforated zinc sheets. Both systems are overlaid with an open-graded asphalt friction course. The systems yield maximum current density and polarized potentials under warm and moist environment conditions.

Failure of riprap protection : phase II (final report).

DOT National Transportation Integrated Search

2008-06-01

Riprap rundowns are often used by the New Mexico Department of Transportation (NMDOT) to : capture and drain the runoff approaching or leaving bridge decks. Rundowns are generally located at : the ends of a bridge deck to transport the water down the...

Optimization, Alternative Materials and Improvements in Body Armor Shields

DTIC Science & Technology

2007-05-10

performance structures such as protective clothing , bullet-proof vests and helmets due to their high-specific strength and stiffness. The ballistic...regard each layer of the woven composite as made of weft and warp yarns, and divide each yam into 3D solid elements. It is found that the frame...0.25 mm thick layers is modeled as an orthotropic material. Even though the woven composite armor is made of yams and each yarn is made of fibers

Electroencephalogram, circulation, and lung function after high-velocity behind armor blunt trauma.

PubMed

Drobin, Dan; Gryth, Dan; Persson, Jonas K E; Rocksén, David; Arborelius, Ulf P; Olsson, Lars-Gunnar; Bursell, Jenny; Kjellström, B Thomas

2007-08-01

Behind armor blunt trauma (BABT) is defined as the nonpenetrating injury resulting from a ballistic impact on personal body armor. The protective vest may impede the projectile, but some of the kinetic energy is transferred to the body, causing internal injuries and occasionally death. The aim in this study was to investigate changes in electroencephalogram (EEG) and physiologic parameters after high-velocity BABT. Eight anesthetized pigs, wearing body armor (including a ceramic plate) on the right side of their thorax, were shot with a 7.62-mm assault rifle (velocity approximately 800 m/s). The shots did not penetrate the armor and these animals were compared with control animals (n = 4), shot with blank ammunition. EEG and several physiologic parameters were thereafter monitored during a 2-hour period after the shot. All animals survived during the experimental period. Five of the exposed animals showed a temporary effect on EEG. Furthermore, exposed animals displayed decreased cardiac capacity and an impaired oxygenation of the blood. Postmortem examination revealed subcutaneous hematomas and crush injuries to the right lung. The results in our animal model indicate that high-velocity BABT induce circulatory and respiratory dysfunction, and in some cases even transient cerebral functional disturbances.

Armored Enzyme-Nanohybrids and Their Catalytic Function Under Challenging Conditions.

PubMed

Zore, Omkar V; Kasi, Rajeswari M; Kumar, Challa V

2017-01-01

Synthesis and characterization of highly stable and functional bienzyme-polymer triads assembled on layered graphene oxide (GO) are described here. Glucose oxidase (GOx) and horseradish peroxidase (HRP) were used as model enzymes and polyacrylic acid (PAA) as model polymer to armor the enzymes. PAA-armored GOx and HRP covalent conjugates were further protected from denaturation by adsorption onto GO nanosheets. Structure and morphology of this enzyme-polymer-nanosheet hybrid biocatalyst (GOx-HRP-PAA/GO) were confirmed by agarose gel electrophoresis, zeta potential, circular dichroism, and transmission electron microscopy. The armored biocatalysts retained full enzymatic activities under challenging conditions of pH (2.5-7.4), warm temperatures (65°C), and presence of chemical denaturants, 4mM sodium dodecyl sulfate, while GOx/HRP physical mixtures without the armor had very little activity under the same conditions. Therefore, this novel combination of two orthogonal approaches, enzyme conjugation with PAA and subsequent physical adsorption onto GO nanosheets, resulted in super stable hybrid biocatalysts that function under harsh conditions. Therefore, this general and powerful approach may be used to design environmentally friendly, green, biocompatible, and biodegradable biocatalysts for energy production in biofuel cell or biobattery applications. © 2017 Elsevier Inc. All rights reserved.

LSD 36 Well Deck Fire Protection

DTIC Science & Technology

1991-05-30

below, which are loaded with personnel, vehicles and supplies. Normally, an Aqueous Film Forming Foam ( AFFF ) sprinkler system would be recommended for...the foam to the center area and allow the AFFF film to spread out from there; or, some combination of the two approaches. Results Phase I Tests A...landing craft and vehicles stored in the well deck below. Based on these tests, the optimum fire protection system would involve an Aqueous Film

Optimization of armored spherical tanks for storage on the lunar surface

NASA Technical Reports Server (NTRS)

Bents, D. J.; Knight, D. A.

1992-01-01

A redundancy strategy for reducing micrometeroid armoring mass is investigated, with application to cryogenic reactant storage for a regenerative fuel cell (RFC) on the lunar surface. In that micrometeoroid environment, the cryogenic fuel must be protected from loss due to tank puncture. The tankage must have a sufficiently high probability of survival over the length of the mission so that the probability of system failure due to tank puncture is low compared to the other mission risk factors. Assuming that a single meteoroid penetration can cause a storage tank to lose its contents, two means are available to raise the probability of surviving micrometeoroid attack to the desired level. One can armor the tanks to a thickness sufficient to reduce probability of penetration of any tank to the desired level or add extra capacity in the form of space tanks that results in survival of a given number out of the ensemble at the desired level. A combination of these strategies (armor and redundancy) is investigated.

49 CFR 176.74 - On deck stowage of break-bulk hazardous materials.

Code of Federal Regulations, 2010 CFR

2010-10-01

... both. Lashing of deck cargo is permitted if eye pads are used to attach the lashings. Lashings may not... water damage must be protected so that it will not be exposed to the weather or to sea water. (c) Not...

Cost effective bridge deck reconstruction in Kansas using high-density concrete overlays and asphalt membrane overlays : final report.

DOT National Transportation Integrated Search

2009-08-01

In 1976 the Federal Highway Administration (FHWA) approved federal aid funding for experimental : installations of corrosion protection for reinforcing steel in existing concrete bridge decks. Sixteen of the sixty-nine : Kansas bridges with Cost Effe...

Fiber-Level Modeling of Dynamic Strength of Kevlar (registered trademark) KM2 Ballistic Fabric

DTIC Science & Technology

2012-07-01

Ballistic-Performance Optimization of a Hybrid Carbon - Nanotube /E-glass Reinforced Poly-Vinyl-Ester-Epoxy-Matrix Com- posite Armor, J. Mater. Sci...2007, 42, p 5347–5359 4. M. Grujicic, W.C. Bell, L.L. Thompson, K.L. Koudela, and B.A. Cheeseman, Ballistic-Protection Performance of Carbon - Nanotube ...Armor via the Use of a Carbon - Nanotube Forest-Mat Strike Face, Mater. Des. Appl., 2008, 222, p 15–28 6. Y. Wang and X. Sun, Determining the Geometry

Interior view of the Flight Deck looking forward, the Commander's ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior view of the Flight Deck looking forward, the Commander's seat and controls are on the left and the pilot's seat and controls are on the right of the view. Note that the flight deck windows have protective covers over them in this view. This images can be digitally stitched with image HAER No. TX-116-A-20 to expand the view to include the overhead control panels of the flight deck. This view was taken in the Orbiter Processing Facility at the Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Military Engineers and Chemical Warfare Troops (Inzhenernye Voiska Khimicheskie Voiska),

DTIC Science & Technology

MILITARY FORCES(FOREIGN), *MILITARY ORGANIZATIONS, MILITARY ENGINEERING , INFANTRY, AMPHIBIOUS OPERATIONS, MINELAYING, ARMORED VEHICLES, NUCLEAR...RADIATION, DOSIMETERS, CHEMICAL WARFARE, PROTECTIVE CLOTHING, DECONTAMINATION, HEALTH PHYSICS.

Promoting Improved Ballistic Resistance of Transparent Armor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wereszczak, Andrew A; Patel, P; Templeton, D W

2011-01-01

Transparent armor is a material or system of materials designed to be optically transparent, yet protect from fragmentation or ballistic impacts. Although engineered to defeat specific threats, or a range of threats, there are general requirements common to all of these designs. The primary requirement for a transparent armor system is to not only defeat the designated threat but also provide a multi-hit capability with minimized distortion of surrounding areas. Ground platforms have several parameters that must be optimized, such as weight, space efficiency, and cost versus performance. Glass exhibits tensile failure stress that is very much dependent on themore » amount of material being stressed, the side being tensile-stressed (i.e., air-versus tin-side if a float glass), and where it is being tensile stressed (i.e., in the middle or near an edge). An axiom arising from those effects is a greater amount of allowable deflection (i.e., higher failure stress) of a ballistically impacted transparent armor will result in improved ballistic resistance. Therefore, the interpretation and management of those tensile-failure-stress dependencies shall ultimately improve ballistic resistance and its predictability of transparent armor. Each of those three dependencies (size, side, and location) in a soda-lime silicate glass is described.« less

An Approach to Analyze Personnel Injury of Reflective Spall from Small-Arms Protective Body Armor

DTIC Science & Technology

2011-07-01

2  Figure 2. Protective plate system on the ORCA human anatomy . .................................................2  Figure 3...stature and is fitted with a medium size protective plate. Representation of the ORCA human anatomy wearing the protective plate system is shown in...Figure 1. Gelatin block placement for experimental testing. Figure 2. Protective plate system on the ORCA human anatomy . Ballistic Gelatin Test

Does the MRAP Meet the US Army’s Needs as the Primary Method of Protecting Troops from the IED Threat?

DTIC Science & Technology

2009-06-12

requirements to protect troops. These requirements include protection, rapid fielding, and suportability . Non-MRAP countermeasures will be examined...at the IED threat to determine requirements to protect troops. These requirements include protection, rapid fielding, and suportability . Non-MRAP...only protect the main torso against this debris, exposing arms and legs to life 11 threatening injury. A countermeasure for this is body armor

29 CFR 1926.432 - Environmental deterioration of equipment.

Code of Federal Regulations, 2014 CFR

2014-07-01

... excessive temperatures. (2) Control equipment, utilization equipment, and busways approved for use in dry...) Protection against corrosion. Metal raceways, cable armor, boxes, cable sheathing, cabinets, elbows...

Armored RNA Technology for Production of Ribonuclease-Resistant Viral RNA Controls and Standards

PubMed Central

Pasloske, Brittan L.; Walkerpeach, Cindy R.; Obermoeller, R. Dawn; Winkler, Matthew; DuBois, Dwight B.

1998-01-01

The widespread use of sensitive assays for the detection of viral and cellular RNA sequences has created a need for stable, well-characterized controls and standards. We describe the development of a versatile, novel system for creating RNase-resistant RNA. “Armored RNA” is a complex of MS2 bacteriophage coat protein and RNA produced in Escherichia coli by the induction of an expression plasmid that encodes the coat protein and an RNA standard sequence. The RNA sequences are completely protected from RNase digestion within the bacteriophage-like complexes. As a prototype, a 172-base consensus sequence from a portion of the human immunodeficiency virus type 1 (HIV-1) gag gene was synthesized and cloned into the packaging vector used to produce the bacteriophage-like particles. After production and purification, the resulting HIV-1 Armored RNA particles were shown to be resistant to degradation in human plasma and produced reproducible results in the Amplicor HIV-1 Monitor assay for 180 days when stored at −20°C or for 60 days at 4°C. Additionally, Armored RNA preparations are homogeneous and noninfectious. PMID:9817878

Highly deformable bones: unusual deformation mechanisms of seahorse armor.

PubMed

Porter, Michael M; Novitskaya, Ekaterina; Castro-Ceseña, Ana Bertha; Meyers, Marc A; McKittrick, Joanna

2013-06-01

Multifunctional materials and devices found in nature serve as inspiration for advanced synthetic materials, structures and robotics. Here, we elucidate the architecture and unusual deformation mechanisms of seahorse tails that provide prehension as well as protection against predators. The seahorse tail is composed of subdermal bony plates arranged in articulating ring-like segments that overlap for controlled ventral bending and twisting. The bony plates are highly deformable materials designed to slide past one another and buckle when compressed. This complex plate and segment motion, along with the unique hardness distribution and structural hierarchy of each plate, provide seahorses with joint flexibility while shielding them against impact and crushing. Mimicking seahorse armor may lead to novel bio-inspired technologies, such as flexible armor, fracture-resistant structures or prehensile robotics. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Low Cost Shore Protection: A Guide for Engineers and Contractors.

DTIC Science & Technology

1981-10-31

pieces; stones should be angular and blocky, not rounded. The toe of the revetment should be located one design wave height (but at least three feet...coefficient from Table 12. Table 12 Stability Coefficients for Stone Revetments Armor Unit KD Quarrystone Smooth rounded 2.1 Rough angular 3.5 Graded riprap...Armor Layers K______D __ K D cot 0 Quarrystone Smooth ztounded 2 2.1 1.7 1.5 to 3.0 Rough angular 2 3.5 12.9 1l.5 Graded riprap Not Recommended A major

Grab them by the Nose and Kick them in the Pants: Patton on Combined Arms Operational Maneuver

DTIC Science & Technology

2010-04-23

said, "we’re winning this war the wrong way, we ought to be going toward Paris .൤ The decision to take the Brittany peninsula and the city of Brest ...towards Brest and the 41h Armored Division south towards Rennes. To support the campaign he gave XIX T AC five different missions: 1. To protect the...4. To assist advancing columns with armored column cover (ACC). 5. To support ground units in the capture of the Brittany ports of Brest , Lorient

The natural armors of fish: A comparison of the lamination pattern and structure of scales

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murcia, Sandra; Lavoie, Ellen; Linley, Tim

Fish scales exhibit a unique balance of flexibility, strength and toughness, which is essential to provide protection without encumbering locomotion. Although the mechanical behavior and structure of this natural armor are of recent interest, a comparison of these qualities from scales of different fish species has not been reported. In this investigation the armor of fish with different locomotion, size and protection needs were analyzed. Scales from the Arapaima gigas, the tarpon (Megalops atlanticus) and the carp (Cyprinus carpio) were compared in terms of the stacking sequence of individual plies and their microstructure. The scales were also compared with respectmore » to anatomical position to distinguish site-specific functional differences. Results show that the lamination sequence of plies for the carp and tarpon exhibit a Bouligand structure with relative rotation of 75° between consecutive plies. The arapaima scales exhibit a cross-ply structure, with 90° rotation between adjacent plies. In addition, results indicate that the volume fraction of reinforcement, the number of plies and the variations in thickness with anatomical position are unique amongst the three fish. These characteristics should be considered in evaluations focused on the mechanical behavior.« less

Researches on the behaviour of cellular antiballistic composites based on AlMg-SiC alloys

NASA Astrophysics Data System (ADS)

Bălţătescu, O.; Florea, R. M.; Rusu, I.; Carcea, I.

2015-11-01

The researches presented in this paper refers basically to the impact of a small/medium caliber bullet shot on a light armor built on the base of a AlMg-SiC metallic composite cellular/foam. Thus, we study the antiballistic behavior and protection properties of the armor, based on the effects that occur at the impact zone of the bullet with the composite surface. We performed an antiballistic behavior modeling by means of a finite element analysis, based on a "multi grid" Fast Finite Element (FFE) system. We used for this purpose the DYNA 2D software package. The obtained samples show after the impact the occurrence of concentration / deformation pores effect and intercellular cracks development to the interior of the composite. Those effects, depending on speed, mass and length of the projectile ballistic trajectory, reduce zonal tensions due to the effect of cell walls deformation. It was obtained a good correlation between modeling results and the electron microscope analyse of the impact area. It is worth mentioning that almost all values for impact energy absorbed by the composite armor are in the protection active zone provided by it.

Warfighter Information Network-Tactical Increment 3 (WIN-T Inc 3)

DTIC Science & Technology

2015-12-01

than 1 seconds. Force Protection Armor required to protect personnel operating WIN-T vehicles employed at BCT, Fires, AVN , BfSB, and select force...21, 2016 18:26:36 UNCLASSIFIED 12 Acronyms and Abbreviations AOR - Area of Responsibility ATH - At-the-Halt ATO - Approval to Operate AVN

UAV Swarm Attack: Protection System Alternatives for Destroyers

DTIC Science & Technology

2012-12-01

Tactical Rocket-Propelled Grenade Airbag Protection System TRL - Technology Readiness Level UAV - Unmanned Aerial Vehicle USN - United States...com- posed of 62 DDGs is $2.014 billion dollars for the 12 year life cycle. J. REACTIVE ARMOR The Tactical Rocket-Propelled Grenade (RPG) Airbag ...Protection System (TRAPS) system involves ‘close-in’ protection using airbags located around a vehicle to minimize the damage from RPGs. This system was

United States Army Rangers in Somalia: an analysis of combat casualties on an urban battlefield.

PubMed

Mabry, R L; Holcomb, J B; Baker, A M; Cloonan, C C; Uhorchak, J M; Perkins, D E; Canfield, A J; Hagmann, J H

2000-09-01

This study was undertaken to determined the differences in injury patterns between soldiers equipped with modern body armor in an urban environment compared with the soldiers of the Vietnam War. From July 1998 to March 1999, data were collected for a retrospective analysis on all combat casualties sustained by United States military forces in Mogadishu, Somalia, on October 3 and 4, 1993. This was the largest and most recent urban battle involving United States ground forces since the Vietnam War. There were 125 combat casualties. Casualty distribution was similar to that of Vietnam; 11% died on the battlefield, 3% died after reaching a medical facility, 47% were evacuated, and 39% returned to duty. The incidence of bullet wounds in Somalia was higher than in Vietnam (55% vs. 30%), whereas there were fewer fragment injuries (31% vs. 48%). Blunt injury (12%) and burns (2%) caused the remaining injuries in Somalia. Fatal penetrating injuries in Somalia compared with Vietnam included wounds to the head and face (36% vs. 35%), neck (7% vs. 8%), thorax (14% vs. 39%), abdomen (14% vs. 7%), thoracoabdominal (7% vs. 2%), pelvis (14% vs. 2%), and extremities (7% vs. 7%). No missiles penetrated the solid armor plate protecting the combatants' anterior chests and upper abdomens. Most fatal penetrating injuries were caused by missiles entering through areas not protected by body armor, such as the face, neck, pelvis, and groin. Three patients with penetrating abdominal wounds died from exsanguination, and two of these three died after damage-control procedures. The incidence of fatal head wounds was similar to that in Vietnam in spite of modern Kevlar helmets. Body armor reduced the number of fatal penetrating chest injuries. Penetrating wounds to the unprotected face, groin, and pelvis caused significant mortality. These data may be used to design improved body armor.

Blast shock wave mitigation using the hydraulic energy redirection and release technology.

PubMed

Chen, Yun; Huang, Wei; Constantini, Shlomi

2012-01-01

A hydraulic energy redirection and release technology has been developed for mitigating the effects of blast shock waves on protected objects. The technology employs a liquid-filled plastic tubing as a blast overpressure transformer to transfer kinetic energy of blast shock waves into hydraulic energy in the plastic tubings. The hydraulic energy is redirected through the plastic tubings to the openings at the lower ends, and then is quickly released with the liquid flowing out through the openings. The samples of the specifically designed body armor in which the liquid-filled plastic tubings were installed vertically as the outer layer of the body armor were tested. The blast test results demonstrated that blast overpressure behind the body armor samples was remarkably reduced by 97% in 0.2 msec after the liquid flowed out of its appropriate volume through the openings. The results also suggested that a volumetric liquid surge might be created when kinetic energy of blast shock wave was transferred into hydraulic energy to cause a rapid physical movement or displacement of the liquid. The volumetric liquid surge has a strong destructive power, and can cause a noncontact, remote injury in humans (such as blast-induced traumatic brain injury and post-traumatic stress disorder) if it is created in cardiovascular system. The hydraulic energy redirection and release technology can successfully mitigate blast shock waves from the outer surface of the body armor. It should be further explored as an innovative approach to effectively protect against blast threats to civilian and military personnel.

Blast Shock Wave Mitigation Using the Hydraulic Energy Redirection and Release Technology

PubMed Central

Chen, Yun; Huang, Wei; Constantini, Shlomi

2012-01-01

A hydraulic energy redirection and release technology has been developed for mitigating the effects of blast shock waves on protected objects. The technology employs a liquid-filled plastic tubing as a blast overpressure transformer to transfer kinetic energy of blast shock waves into hydraulic energy in the plastic tubings. The hydraulic energy is redirected through the plastic tubings to the openings at the lower ends, and then is quickly released with the liquid flowing out through the openings. The samples of the specifically designed body armor in which the liquid-filled plastic tubings were installed vertically as the outer layer of the body armor were tested. The blast test results demonstrated that blast overpressure behind the body armor samples was remarkably reduced by 97% in 0.2 msec after the liquid flowed out of its appropriate volume through the openings. The results also suggested that a volumetric liquid surge might be created when kinetic energy of blast shock wave was transferred into hydraulic energy to cause a rapid physical movement or displacement of the liquid. The volumetric liquid surge has a strong destructive power, and can cause a noncontact, remote injury in humans (such as blast-induced traumatic brain injury and post-traumatic stress disorder) if it is created in cardiovascular system. The hydraulic energy redirection and release technology can successfully mitigate blast shock waves from the outer surface of the body armor. It should be further explored as an innovative approach to effectively protect against blast threats to civilian and military personnel. PMID:22745740

46 CFR 34.20-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... to give primary protection to the spaces over the cargo tanks. (b) Rate of application. The water... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum.../min per square meter of the horizontal sectional area of the single tank having the largest such area...

3D-printing and mechanics of bio-inspired articulated and multi-material structures.

PubMed

Porter, Michael M; Ravikumar, Nakul; Barthelat, Francois; Martini, Roberto

2017-09-01

3D-printing technologies allow researchers to build simplified physical models of complex biological systems to more easily investigate their mechanics. In recent years, a number of 3D-printed structures inspired by the dermal armors of various fishes have been developed to study their multiple mechanical functionalities, including flexible protection, improved hydrodynamics, body support, or tail prehensility. Natural fish armors are generally classified according to their shape, material and structural properties as elasmoid scales, ganoid scales, placoid scales, carapace scutes, or bony plates. Each type of dermal armor forms distinct articulation patterns that facilitate different functional advantages. In this paper, we highlight recent studies that developed 3D-printed structures not only to inform the design and application of some articulated and multi-material structures, but also to explain the mechanics of the natural biological systems they mimic. Copyright © 2017 Elsevier Ltd. All rights reserved.

CD28z CARs and Armored CARs

PubMed Central

Pegram, Hollie J.; Park, Jae H.; Brentjens, Renier J.

2015-01-01

CD19-targeted chimeric antigen receptor (CAR) T cells are currently being tested in the clinic with very promising outcomes. However, limitations to CAR T cell therapy exist. These include lack of efficacy against some tumors, specific targeting of tumor cells without affecting normal tissue and retaining activity within the suppressive tumor microenvironment. Whilst promising clinical trials are in progress, preclinical development is focused on optimizing CAR design, to generate “armored CAR T cells” which are protected from the inhibitory tumor microenvironment. Studies investigating the expression of cytokine transgenes, combination therapy with small molecule inhibitors or monoclonal antibodies are aimed at improving the anti-tumor efficacy of CAR T cell therapy. Other strategies aimed at improving CAR T cell therapy include utilizing dual CARs and chemokine receptors to more specifically target tumor cells. This review will describe the current clinical data and some novel “armored CAR T cell” approaches for improving anti-tumor efficacy therapy. PMID:24667958

CD28z CARs and armored CARs.

PubMed

Pegram, Hollie J; Park, Jae H; Brentjens, Renier J

2014-01-01

CD19-targeted chimeric antigen receptor (CAR) T cells are currently being tested in the clinic with very promising outcomes. However, limitations to CAR T cell therapy exist. These include lack of efficacy against some tumors, specific targeting of tumor cells without affecting normal tissue and retaining activity within the suppressive tumor microenvironment. Whereas promising clinical trials are in progress, preclinical development is focused on optimizing CAR design, to generate "armored CAR T cells," which are protected from the inhibitory tumor microenvironment. Studies investigating the expression of cytokine transgenes, combination therapy with small molecule inhibitors, or monoclonal antibodies, are aimed at improving the antitumor efficacy of CAR T cell therapy. Other strategies aimed at improving CAR T cell therapy include using dual CARs and chemokine receptors to more specifically target tumor cells. This review will describe the current clinical data and some novel armored CAR T cell approaches for improving antitumor efficacy therapy.

Archway for Radiation and Micrometeorite Occurrence Resistance

NASA Technical Reports Server (NTRS)

Giersch, Louis R.

2012-01-01

The environmental conditions of the Moon require mitigation if a long-term human presence is to be achieved for extended periods of time. Radiation, micrometeoroid impacts, high-velocity debris, and thermal cycling represent threats to crew, equipment, and facilities. For decades, local regolith has been suggested as a candidate material to use in the construction of protective barriers. A thickness of roughly 3m is sufficient protection from both direct and secondary radiation from cosmic rays and solar protons; this thickness is sufficient to reduce radiation exposure even during solar flares. NASA has previously identified a need for innovations that will support lunar habitats using lightweight structures because the reduction of structural mass translates directly into additional up and down mass capability that would facilitate additional logistics capacity and increased science return for all mission phases. The development of non-pressurized primary structures that have synergy with the development of pressurized structures is also of interest. The use of indigenous or in situ materials is also a well-known and active area of research that could drastically improve the practicality of human exploration beyond low-Earth orbit. The Archway for Radiation and Micrometeorite Occurrence Resistance (ARMOR) concept is a new, multifunctional structure that acts as radiation shielding and micrometeorite impact shielding for long-duration lunar surface protection of humans and equipment. ARMOR uses a combination of native regolith and a deployed membrane jacket to yield a multifunctional structure. ARMOR is a robust and modular system that can be autonomously assembled on-site prior to the first human surface arrival. The system provides protection by holding a sufficiently thick (3 m) archshaped shell of local regolith around a central cavity. The regolith is held in shape by an arch-shaped jacket made of strong but deployable material. No regolith processing is required. During the regolith filling process, an inflatable structure under the arch supports the mass of the regolith, but once regolith filling is complete the catenary arch formed by the regolith and the jacket becomes self-supporting and the inflatable can be deflated and removed. When complete, habitat modules and equipment can be moved into the protected cavity under the arch. ARMOR is a nearterm system that would provide a reliable and robust lightweight structure technology to support large lunar habitats, drastically lower launch mass, and improve efficient volume use, reducing launch costs.

Well logging evaporative thermal protection system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lamers, M.D.; Martelli, V.P.

1981-02-03

An evaporative thermal protection system for use in hostile environment well logging applications, the system including a downhole thermal protection cartridge disposed within a well logging sonde or tool to keep a payload such as sensors and support electronics cool, the cartridge carrying either an active evaporative system for refrigeration or a passive evaporative system, both exhausting to the surface through an armored flexible fluidic communication mechanical cable.

Natural Mallow Fiber-Reinforced Epoxy Composite for Ballistic Armor Against Class III-A Ammunition

NASA Astrophysics Data System (ADS)

Nascimento, Lucio Fabio Cassiano; Holanda, Luane Isquerdo Ferreira; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Gomes, Alaelson Vieira; Lima, Édio Pereira

2017-10-01

Epoxy matrix composites reinforced with up to 30 vol pct of continuous and aligned natural mallow fibers were for the first time ballistic tested as personal armor against class III-A 9 mm FMJ ammunition. The ballistic efficiency of these composites was assessed by measuring the dissipated energy and residual velocity after the bullet perforation. The results were compared to those in similar tests of aramid fabric (Kevlar™) commonly used in vests for personal protections. Visual inspection and scanning electron microscopy analysis of impact-fractured samples revealed failure mechanisms associated with fiber pullout and rupture as well as epoxy cracking. As compared to Kevlar™, the mallow fiber composite displayed practically the same ballistic efficiency. However, there is a reduction in both weight and cost, which makes the mallow fiber composites a promising material for personal ballistic protection.

Detail view of the interior of the flight deck looking ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail view of the interior of the flight deck looking forward showing the overhead control panels. Note that the flight deck windows have protective covers over them in this view. This images can be digitally stitched with image HAER No. TX-116-A-19 to expand the view to include the Commander and Pilot positions during ascent and reentry and landing. This view was taken in the Orbiter Processing Facility at the Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Analysis of behind the armor ballistic trauma.

PubMed

Wen, Yaoke; Xu, Cheng; Wang, Shu; Batra, R C

2015-05-01

The impact response of body armor composed of a ceramic plate with an ultrahigh molecular weight polyethylene (UHMWPE) fiber-reinforced composite and layers of UHMWPE fibers shielding a block of ballistic gelatin has been experimentally and numerically analyzed. It is a surrogate model for studying injuries to human torso caused by a bullet striking body protection armor placed on a person. Photographs taken with a high speed camera are used to determine deformations of the armor and the gelatin. The maximum depth of the temporary cavity formed in the ballistic gelatin and the peak pressure 40mm behind the center of the gelatin front face contacting the armor are found to be, respectively, ~34mm and ~15MPa. The Johnson-Holmquist material model has been used to simulate deformations and failure of the ceramic. The UHMWPE fiber-reinforced composite and the UHMWPE fiber layers are modeled as linear elastic orthotropic materials. The gelatin is modeled as a strain-rate dependent hyperelastic material. Values of material parameters are taken from the open literature. The computed evolution of the temporary cavity formed in the gelatin is found to qualitatively agree with that seen in experiments. Furthermore, the computed time histories of the average pressure at four points in the gelatin agree with the corresponding experimentally measured ones. The maximum pressure at a point and the depth of the temporary cavity formed in the gelatin can be taken as measures of the severity of the bodily injury caused by the impact; e.g. see the United States National Institute of Justice standard 0101.06-Ballistic Resistance of Body Armor. Copyright © 2015 Elsevier Ltd. All rights reserved.

77 FR 43474 - Defense Federal Acquisition Regulation Supplement; Specialty Metals-Definition of “Produce...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-24

... DoD's demand and that the number of specialty metal steel manufacturers has increased since 2006. DoD... steel armor to meet peak demand to satisfy critical need for Mine Resistant Ambush Protection (MRAP... Protection and an Incentive to U.S. Manufacturers and Create Jobs Comment: Many respondents addressed the...

14 CFR 29.1439 - Protective breathing equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... harmful gases while on flight deck duty; (2) That equipment must include— (i) Masks covering the eyes, nose, and mouth; or (ii) Masks covering the nose and mouth, plus accessory equipment to protect the...

Cathodic protection of concrete bridge decks using titanium-mesh anodes.

DOT National Transportation Integrated Search

2000-02-01

Anodes are a critical component of cathodic protection systems. A continuous research effort in Virginia is being aimed at searching for the most suitable anode for use in cathodic protection of the various types of concrete bridge components that ar...

46 CFR 34.20-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 1 2012-10-01 2012-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5..., Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum...

46 CFR 34.20-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 1 2013-10-01 2013-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5..., Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum...

46 CFR 34.20-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 1 2014-10-01 2014-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5..., Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum...

Interim report : a non-overlay cathodic protection system.

DOT National Transportation Integrated Search

1983-01-01

This interim report describes Virginia's experience in installing its first cathodic protection system for a bridge deck. The installation was completed with practically no problems. Very minor problems have been encountered with the rectifier/contro...

Crimp-Imbalanced Protective (CRIMP) Fabrics

DTIC Science & Technology

2010-03-31

ILLUSTRATIONS ii LIST OF TABLES iv LIST OF ABBREVIATIONS, ACRONYMS, AND SYMBOLS iv INTRODUCTION 1 THREAT TYPES AND PROTECTION LEVELS 2 HISTORICAL...velocity 3-D Three-dimensional v (vi blank) CRIMP-IMBALANCED PROTECTIVE (CRIMP) FABRICS INTRODUCTION Lightweight, soft-armor systems have...1200 ft/sec D-4 (qi-uO /(B jaug UIBJJS 3i;sei3 (qi-uO 3* dSd ui uoipnpay > .’/ .7 • ’/ i •’/ !/ / *- IT> *- m y / II

Pangolin armor: Overlapping, structure, and mechanical properties of the keratinous scales.

PubMed

Wang, Bin; Yang, Wen; Sherman, Vincent R; Meyers, Marc A

2016-09-01

The pangolin has a flexible dermal armor consisting of overlapping keratinous scales. Although they show potential for bioinspired flexible armor, the design principles of pangolin armor are barely known. Here we report on the overlapping organization, hierarchical structure (from the nano to the mesolevel), and mechanical response of scales from ground (Chinese) and arboreal (African tree) pangolins. Both scales exhibit the same overlapping organization, with each scale at the center of neighboring scales arranged in a hexagonal pattern. The scales have a cuticle of several layers of loosely attached flattened keratinized cells, while the interior structure exhibits three regions distinguished by the geometry and orientations of the keratinized cells, which form densely packed lamellae; each one corresponds to one layer of cells. Unlike most other keratinous materials, the scales show a crossed-lamellar structure (∼5μm) and crossed fibers (∼50μm). A nano-scale suture structure, observed for the first time, outlines cell membranes and leads to an interlocking interface between lamellae, thus enhancing the bonding and shear resistance. The tensile response of the scales shows an elastic limit followed by a short plateau prior to failure, with Young's modulus ∼1 GPa and tensile strength 60-100MPa. The mechanical response is transversely isotropic, a result of the cross lamellar structure. The strain rate sensitivity in the range of 10(-5)-10(-1)s(-1) region is found to be equal to 0.07-0.08, typical of other keratins and polymers. The mechanical response is highly dependent on the degree of hydration, a characteristic of keratins. Although many fish and reptiles have protective scales and carapaces, mammals are characteristically fast and light. The pangolin is one of the few mammal possessing a flexible dermal armor for protection from predators, such as lions. Here we study the arrangement of the scales as well as their hierarchical structure from the nano to the mesolevel and correlate it to the mechanical properties. The study reveals a unique structure consisting of crossed lamellae and interlocking sutures that provide exceptional performance and in-plane isotropy. Copyright © 2016. Published by Elsevier Ltd.

Influence of particle size on the low and high strain rate behavior of dense colloidal dispersions of nanosilica

NASA Astrophysics Data System (ADS)

Asija, Neelanchali; Chouhan, Hemant; Gebremeskel, Shishay Amare; Bhatnagar, Naresh

2017-01-01

Shear thickening is a non-Newtonian flow behavior characterized by the increase in apparent viscosity with the increase in applied shear rate, particularly when the shear rate exceeds a critical value termed as the critical shear rate (CSR). Due to this remarkable property of shear-thickening fluids (STFs), they are extensively used in hip protection pads, protective gear for athletes, and more recently in body armor. The use of STFs in body armor has led to the development of the concept of liquid body armor. In this study, the effect of particle size is explored on the low and high strain rate behavior of nanosilica dispersions, so as to predict the efficacy of STF-aided personal protection systems (PPS), specifically for ballistic applications. The low strain rate study was conducted on cone and plate rheometer, whereas the high strain rate characterization of STF was conducted on in-house fabricated split Hopkinson pressure bar (SHPB) system. Spherical nanosilica particles of three different sizes (100, 300, and 500 nm) as well as fumed silica particles of four different specific surface areas (Aerosil A-90, A-130, A-150, and A-200), respectively, were used in this study. The test samples were prepared by dispersing nanosilica particles in polypropylene glycol (PPG) using ultrasonic homogenization method. The low strain rate studies aided in determining the CSR of the synthesized STF dispersions, whereas the high strain rate studies explored the impact-resisting ability of STFs in terms of the impact toughness and the peak stress attained during the impact loading of STF in SHPB testing.

Finite Element Based Optimization of Material Parameters for Enhanced Ballistic Protection

NASA Astrophysics Data System (ADS)

Ramezani, Arash; Huber, Daniel; Rothe, Hendrik

2013-06-01

The threat imposed by terrorist attacks is a major hazard for military installations, vehicles and other items. The large amounts of firearms and projectiles that are available, pose serious threats to military forces and even civilian facilities. An important task for international research and development is to avert danger to life and limb. This work will evaluate the effect of modern armor with numerical simulations. It will also provide a brief overview of ballistic tests in order to offer some basic knowledge of the subject, serving as a basis for the comparison of simulation results. The objective of this work is to develop and improve the modern armor used in the security sector. Numerical simulations should replace the expensive ballistic tests and find vulnerabilities of items and structures. By progressively changing the material parameters, the armor is to be optimized. Using a sensitivity analysis, information regarding decisive variables is yielded and vulnerabilities are easily found and eliminated afterwards. To facilitate the simulation, advanced numerical techniques have been employed in the analyses.

The application of PA/CF in stab resistance body armor

NASA Astrophysics Data System (ADS)

Yuan, M. Q.; Liu, Y.; Gong, Z.; Qian, X. M.

2017-06-01

Stab resistance body armor (SRBA) is an essential defensive equipment to protect human body against injuries from stabbing. The conventional SRBAs shared low wearing frequency since they are heavy and poor in flexibility. This paper designed a structured stab-resistance plate using the model of crocodile armor and manufactured using 3D printing technology-laser sintering (LS). CF(Carbon fiber) was applied to enhance the stab resistance properties of SRBA. The effects of the material and structure were analysed through the stab resistance property tests based on the national standard GA68-2008. It is found that the stab resistance property of flat plates sintered by PA powder and PA/CF are both weaker than that of the structured plate. The penetrating depth of PA/CF structured plate is significantly 2-mm-less than the pure PA structured plate. The SEM observations confirmed the conclusion that addition of the CF largely improved the plate stab resistance property. Moreover, using PA/CF structured plate to produce the stab resistance body armor would result in a weight reduction by about 30-40% as compared to the existing SRBA that was made up of metal plates, which could largely reduce the wearer physical burden and improve the wearing frequency.

Electrically conductive concrete : a laboratory study.

DOT National Transportation Integrated Search

1987-01-01

In the cathodic protection of existing reinforced concrete bridge decks, there is a need for a simple secondary-anode system to facilitate the distribution of direct current over the structure being protected. It is believed that a durable, electrica...

Structure and mechanical behaviors of protective armored pangolin scales and effects of hydration and orientation.

PubMed

Liu, Z Q; Jiao, D; Weng, Z Y; Zhang, Z F

2016-03-01

As natural flexible dermal armor, pangolin scales provide effective protection against predatory threats and possess other notable properties such as anti-adhesion and wear-resistance. In this study, the structure, mechanical properties, deformation and damage behaviors of pangolin scales were systematically investigated with the effects of hydration and orientation evaluated. The scales are divided into three macro-layers constituted by overlapping keratin tiles with distinct lamellar arrangements which are further composed of lower-ordered lamellae. Both hardness and strength are significantly decreased by hydration; while the plasticity is markedly improved concomitantly, and as such, the mechanical damages are mitigated. The tensile strength invariably approximates to one third of hardness in value. The tensile deformation is dominated by lamellae stretching and pulling out under wet condition, which is distinct from the trans-lamellar fracture in dry samples. The compressive behaviors are featured by pronounced plasticity in both dry and wet scales; and notable strain-hardening capacity is introduced by hydration, especially along the thickness direction wherein kinking occurs. Inter-lamellar cracking is effectively alleviated in wet samples compared with the dry ones and both of them deform by macroscopic buckling. This study may help stimulate possible inspiration for the design of high-performance synthetic armor materials by mimicking pangolin scales. Copyright © 2015 Elsevier Ltd. All rights reserved.

Epoxy coated reinforcement in bridge decks

NASA Astrophysics Data System (ADS)

Wills, J.

A review was conducted of methods relating to the use of epoxy coated reinforcing bars for bridge decks and their potential for use in the United Kingdom. A survey of work carried out in the USA was carried out and the analysis used in a preliminary cost study. The options of having either a hot rolled asphalt surfacing or a permanently exposed concrete wearing surface were considered. It was concluded that epoxy coating of the top steel in addition to current waterproofing practice would provide, at relatively little extra cost, additional assurance that the reinforcement would be adequately protected throughout the life of a bridge. Current design rules do not permit decks with permanently exposed concrete wearing surface without waterproofing. Epoxy coating may afford a means of introducing such decks but before a positive recommendation to delete waterproofing can be made further studies would have to be undertaken.

Multiscale Mechanical Characterization of Biomimetic Gels for Army Applications

DTIC Science & Technology

2006-11-01

organs is critical for the design of protective equipment used in the automotive, body armor, and sports industries, among others. Improved...displacement curve. The total displaced volume is hrV 2π= . (9) The relations in this section are used to compute

Experimental galvanic anode for cathodic protection of Bridge A12112

DOT National Transportation Integrated Search

2010-11-01

Cathodic Protection (CP) has been used by MoDOT for more than 30 years to stop : corrosion of reinforced concrete bridge decks. These systems require power from local electrical : connections. A galvanic system uses the difference in electrical poten...

Visual evaluation of smoke-protective devices.

DOT National Transportation Integrated Search

1976-05-01

This study was designed to determine the visual characteristics of smoke-protective devices for flight deck crews. Visual measurements were made on five male subjects, who ranged in age from 35 to 54, while they were wearing each of the 26 devices te...

46 CFR 36.05-10 - Protection of personnel-TB/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 1 2011-10-01 2011-10-01 false Protection of personnel-TB/ALL. 36.05-10 Section 36.05-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS ELEVATED TEMPERATURE CARGOES Cargo Tanks § 36.05-10 Protection of personnel—TB/ALL. (a) Decks, bulkheads, or other structures shall...

46 CFR 36.05-10 - Protection of personnel-TB/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Protection of personnel-TB/ALL. 36.05-10 Section 36.05-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS ELEVATED TEMPERATURE CARGOES Cargo Tanks § 36.05-10 Protection of personnel—TB/ALL. (a) Decks, bulkheads, or other structures shall...

General view of the middeck of the Orbiter Discovery while ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General view of the mid-deck of the Orbiter Discovery while in the Orbiter Processing Facility at Kennedy Space Center. The view is looking through the air lock and into the payload bay. In the foreground note the ladders and access hatches to the flight deck and the ground support panels used to protect the floors. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Polymer concrete overlay on SH-51, bridge deck

NASA Astrophysics Data System (ADS)

Borg, T. M.

1982-06-01

A thin resinous overlay was placed on a sound bridge deck in Oklahoma to evaluate its performance over one year using various physical tests. The evaluation shows how well the overlay protects the reinforcing steel from corrosion due to deicing salts. The steps leading to the construction of the overlay are detailed as well as the actual placing of the overlay. The results of various physical tests are reported for both before and after the overlay.

The design of a multimegawatt heat pipe radiator for an inertial fusion rocket powered manned Mars mission

NASA Technical Reports Server (NTRS)

Murray, K. A.

1988-01-01

A system of heat pipe radiators has been designed to provide waste heat rejection for an inertial fusion powered spacecraft capable of manned missions to other planets. The radiators are arrays of unfinned, arterial heat pipes operating at 1500 and 900 K. Liquid metal coolant carries up to 8000 MW of waste heat through feed pipes from on-board components (laser drivers and coil shield). The radiators do not rely on armor for protection from micrometeoroid penetration. An armored radiator design for this application with a 99 percent survivability would have a specific mass of 0.06 to 0.11 kg/kW at 1500 K. Instead, a segmentation of heat pipes is used, and bumpers are utilized to protect the feed pipes. This design reduces the specific mass to 0.015 to 0.04 kg/kW for the coil shield radiator (1500 K) and 0.06 to 0.12 kg/kW for the laser driver radiator (900 K).

Mallow Fiber-Reinforced Epoxy Composites in Multilayered Armor for Personal Ballistic Protection

NASA Astrophysics Data System (ADS)

Nascimento, Lucio Fábio Cassiano; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Lima, Édio Pereira; da Luz, Fernanda Santos

2017-10-01

Lighter and less expensive polymer composites reinforced with natural fibers have been investigated as possible components of a multilayered armor system (MAS) for personal protection against high-velocity ammunition. Their ballistic performance was consistently found comparable with that of conventional Kevlar® synthetic aramid fiber. Among the numerous existing natural fibers with the potential for reinforcing polymer composites to replace Kevlar® in MAS, mallow fiber has not been fully investigated. Thus, the objective of this work is to evaluate the ballistic performance of epoxy composites reinforced with 30 vol.% of aligned mallow fibers as a second MAS layer backing a front ceramic plate. The results using high-velocity 7.62 ammunition show a similar indentation to a Kevlar® layer with the same thickness. An impedance matching calculation supports the similar ballistic performance of mallow fiber composite and Kevlar®. Reduced MAS costs associated with the mallow fiber composite are practical advantages over Kevlar®.

Combat body armor and injuries to the head, face, and neck region: a systematic review.

PubMed

Tong, Darryl; Beirne, Ross

2013-04-01

There has been a reported increase in combat-related head, face, and neck (HFN) injuries among service personnel wearing combat body armor (CBA) that have deployed to Iraq and Afghanistan. Modern ceramic plate CBA has decreased the incidence of fatal-penetrating injuries to the torso but offers no protection to the limbs and face which remain exposed to gunshot wounds and fragments from explosive devices. The aim of this review was to systematically summarize the literature reporting on HFN injuries sustained by combat personnel wearing CBA and to highlight recommendations for increased protection to the facial region. Three major contributing factors were identified with this proportional increase in HFN injuries, namely the increased survivability of soldiers because of CBA, fragments injuries from explosive devices, and the lack of protection to the face and limbs. There appears to be no evidence to suggest that by virtue of wearing CBA the likelihood of sustaining an HFN injury increases as such, but a higher incidence of fragment injuries to the HFN region may be due to the more common use of improvised explosive devicess and other explosive devices. Further development of lightweight protection for the face is needed. Reprint & Copyright © 2013 Association of Military Surgeons of the U.S.

Reducing commercial fishing deck hazards with engineering solutions for winch design.

PubMed

Lincoln, Jennifer M; Lucas, Devin L; McKibbin, Robert W; Woodward, Chelsea C; Bevan, John E

2008-01-01

The majority (67%) of hospitalized injuries among Alaska commercial fishermen are associated with deck machinery. This paper describes the "Prevention Through Design" process to mitigate one serious machinery entanglement hazard posed by a capstan deck winch. After observing that the capstan winch provides no entanglement protection and the hydraulic controls are usually out of reach of the entangled person, NIOSH personnel met with fishermen and winch manufacturers to discuss various design solutions to mitigate these hazards. An emergency-stop ("e-stop") system was developed that incorporated a momentary contact button that when pushed, switches a safety-relay that de-energizes the solenoid of an electro-hydraulic valve stopping the rotating winch. The vessel owners that had the e-stop installed enthusiastically recommend it to other fishermen. NIOSH entered into a Proprietary Technology Licensing Agreement with a company to develop the system for commercial use. This is an example of a practical engineering control that effectively protects workers from a hazardous piece of equipment by preventing injuries due to entanglement. This solution could reduce these types of debilitating injuries and fatalities in this industry.

Study on Protection Mechanism of 30CrMnMo-UHMWPE Composite Armor

PubMed Central

Zhou, Yu; Li, Guoju; Fan, Qunbo; Wang, Yangwei; Zheng, Haiyang; Tan, Lin; Xu, Xuan

2017-01-01

The penetration of a 30CrMnMo ultra-high molecular weight polyethylene armor by a high-speed fragment was investigated via experiments and simulations. Analysis of the projectile revealed that the nose (of the projectile) is in the non-equilibrium state at the initial stage of penetration, and the low-speed regions undergo plastic deformation. Subsequently, the nose-tail velocities of the projectile were virtually identical and fluctuated together. In addition, the effective combination of the steel plate and polyethylene (PE) laminate resulted in energy absorption by the PE just before the projectile nose impacts the laminate. This early absorption plays a positive role in the ballistic performance of the composite armor. Further analysis of the internal energy and mass loss revealed that the PE laminate absorbs energy via the continuous and stable failure of PE fibers during the initial stages of penetration, and absorbs energy via deformation until complete penetration occurs. The energy absorbed by the laminate accounts for 68% of the total energy absorption, indicating that the laminate plays a major role in energy absorption during the penetration process. PMID:28772764

Vertical electrical impedance evaluation of asphalt overlays on concrete bridge decks

NASA Astrophysics Data System (ADS)

Baxter, Jared S.; Guthrie, W. Spencer; Waters, Tenli; Barton, Jeffrey D.; Mazzeo, Brian A.

2018-04-01

Vertical electrical impedance scanning of concrete bridge decks is a non-destructive method for quantifying the degree of protection provided to steel reinforcement against the ingress of corrosive agents. Four concrete bridge decks with asphalt overlays in northern Utah were evaluated using scanning vertical electrical impedance measurements in this study. At the time of testing, the bridges ranged in age from 21 to 34 years, and asphalt overlays had been in place for 7 to 22 years, depending on the bridge. Electrical impedance measurements were collected using a previously constructed apparatus that consisted of six probes spanning a transverse distance of 12 ft. The impedance measurements were compared to surface cracking observations and cores obtained from the same four bridge decks. The results presented in this paper demonstrate the utility of scanning vertical electrical impedance measurements for detecting cracks in asphalt overlays and quantifying their severity. In addition, the results demonstrate the sensitivity of impedance measurements to the presence of an intact membrane beneath the asphalt overlay.

Sabot high speed interceptor AE 4273 aircraft design

NASA Technical Reports Server (NTRS)

Dober, Dave; Al-Hashel, Waleed; Baldocchi, Bob; Berg, Tim; Lindsay, Curt; Mcatee, Aaron; Sergent, Dan; Dunbrack, Harry

1992-01-01

Today's carrier based deck launched intercept (DLI) mission is a vital one that is aimed at protecting the carrier battle group and detering potential adversaries. The assets deployed on our carrier decks are able to complete this mission but with very limited range. The waverider concept has great potential to increase the range of this carrier based mission. As a result, a request for proposals (RFP) was developed which contains design requirements for an aircraft that can complete this mission through the utilization of waverider technology.

General view of the flight deck of the Orbiter Discovery ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General view of the flight deck of the Orbiter Discovery looking from a low angle up and aft from approximately behind the commander's station. In the view you can see the overhead aft observation windows, the payload operations work area and in this view the payload bay observation windows have protective covers on them. This view was taken at Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

View of east entrance to Flume Tunnel #2. In foreground, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of east entrance to Flume Tunnel #2. In foreground, covered decking (covered by debris) protects the flume below it (not visible). The extreme top of the tunnel entrance is visible in the middle of the picture, just beyond the covered decking. This is typical of gravity tunnel entrances and the only photograph representing these features in the system. Looking south - Childs-Irving Hydroelectric Project, Childs System, Flume Tunnel No. 2, Forest Service Road 708/502, Camp Verde, Yavapai County, AZ

Language Teacher Immunity: A Double-Edged Sword

ERIC Educational Resources Information Center

Hiver, Phil; Dörnyei, Zoltán

2017-01-01

In this paper we introduce a new concept termed "teacher immunity". We propose that this immunity emerges from the accrued experiences of coping with disturbances and problems in stressful teaching environments, and that it functions as an indispensable protective armor allowing language teachers to survive the unavoidable hassles of…

The Effect of Soldier Marching, Rucksack Load, and Heart Rate on Marksmanship

DTIC Science & Technology

2017-04-01

not to be construed as an official Department of the Army position unless so designated by other authorized documents. Citation of manufacturer’s or...marches in forested terrain at 4.3 km/hour on separate days (randomized, counterbalanced design ). The Rifleman load consisted of protective armor...

2008 Tactical Wheeled Vehicles Conference (TWV) Volume 1

DTIC Science & Technology

2008-02-05

additional LSAC cabs FMTV Gunners Restraint (2,022 LSAC; 1,855 RACK) Counterweight bumper for M1078 Cargo with LSAC Cab and GPK 3 Jan 08NDIA TWV Conference...Objective Gunner Protection Kits to support Up-Armored HMMWV’s GPK Upgrade Program. Partnerships: Ensured partnerships with commercial manufacturers

Biophysical Assessment and Predicted Thermophysiologic Effects of Body Armor

PubMed Central

Potter, Adam W.; Gonzalez, Julio A.; Karis, Anthony J.; Xu, Xiaojiang

2015-01-01

Introduction Military personnel are often required to wear ballistic protection in order to defend against enemies. However, this added protection increases mass carried and imposes additional thermal burden on the individual. Body armor (BA) is known to reduce combat casualties, but the effects of BA mass and insulation on the physical performance of soldiers are less well documented. Until recently, the emphasis has been increasing personal protection, with little consideration of the adverse impacts on human performance. Objective The purpose of this work was to use sweating thermal manikin and mathematical modeling techniques to quantify the tradeoff between increased BA protection, the accompanying mass, and thermal effects on human performance. Methods Using a sweating thermal manikin, total insulation (IT, clo) and vapor permeability indexes (im) were measured for a baseline clothing ensemble with and without one of seven increasingly protective U.S. Army BA configurations. Using mathematical modeling, predictions were made of thermal impact on humans wearing each configuration while working in hot/dry (desert), hot/humid (jungle), and temperate environmental conditions. Results In nearly still air (0.4 m/s), IT ranged from 1.57 to 1.63 clo and im from 0.35 to 0.42 for the seven BA conditions, compared to IT and im values of 1.37 clo and 0.45 respectively, for the baseline condition (no BA). Conclusion Biophysical assessments and predictive modeling show a quantifiable relationship exists among increased protection and increased thermal burden and decreased work capacity. This approach enables quantitative analysis of the tradeoffs between ballistic protection, thermal-work strain, and physical work performance. PMID:26200906

Biophysical Assessment and Predicted Thermophysiologic Effects of Body Armor.

PubMed

Potter, Adam W; Gonzalez, Julio A; Karis, Anthony J; Xu, Xiaojiang

2015-01-01

Military personnel are often required to wear ballistic protection in order to defend against enemies. However, this added protection increases mass carried and imposes additional thermal burden on the individual. Body armor (BA) is known to reduce combat casualties, but the effects of BA mass and insulation on the physical performance of soldiers are less well documented. Until recently, the emphasis has been increasing personal protection, with little consideration of the adverse impacts on human performance. The purpose of this work was to use sweating thermal manikin and mathematical modeling techniques to quantify the tradeoff between increased BA protection, the accompanying mass, and thermal effects on human performance. Using a sweating thermal manikin, total insulation (IT, clo) and vapor permeability indexes (im) were measured for a baseline clothing ensemble with and without one of seven increasingly protective U.S. Army BA configurations. Using mathematical modeling, predictions were made of thermal impact on humans wearing each configuration while working in hot/dry (desert), hot/humid (jungle), and temperate environmental conditions. In nearly still air (0.4 m/s), IT ranged from 1.57 to 1.63 clo and im from 0.35 to 0.42 for the seven BA conditions, compared to IT and im values of 1.37 clo and 0.45 respectively, for the baseline condition (no BA). Biophysical assessments and predictive modeling show a quantifiable relationship exists among increased protection and increased thermal burden and decreased work capacity. This approach enables quantitative analysis of the tradeoffs between ballistic protection, thermal-work strain, and physical work performance.

40 CFR 63.1064 - Alternative means of emission limitation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Standards, Chapter 19, Section 3, Part A, Wind Tunnel Test Method for the Measurement of Deck-Fitting Loss... limitation. 63.1064 Section 63.1064 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... as wind, temperature, and barometric pressure. Test methods that can be used to perform the testing...

40 CFR 63.1064 - Alternative means of emission limitation.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Standards, Chapter 19, Section 3, Part A, Wind Tunnel Test Method for the Measurement of Deck-Fitting Loss... limitation. 63.1064 Section 63.1064 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... as wind, temperature, and barometric pressure. Test methods that can be used to perform the testing...

40 CFR 63.1064 - Alternative means of emission limitation.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Standards, Chapter 19, Section 3, Part A, Wind Tunnel Test Method for the Measurement of Deck-Fitting Loss... limitation. 63.1064 Section 63.1064 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... as wind, temperature, and barometric pressure. Test methods that can be used to perform the testing...

40 CFR 63.1064 - Alternative means of emission limitation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards, Chapter 19, Section 3, Part A, Wind Tunnel Test Method for the Measurement of Deck-Fitting Loss... limitation. 63.1064 Section 63.1064 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... as wind, temperature, and barometric pressure. Test methods that can be used to perform the testing...

40 CFR 63.1064 - Alternative means of emission limitation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards, Chapter 19, Section 3, Part A, Wind Tunnel Test Method for the Measurement of Deck-Fitting Loss... limitation. 63.1064 Section 63.1064 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... as wind, temperature, and barometric pressure. Test methods that can be used to perform the testing...

Injuries to law enforcement officers: the backface signature injury.

PubMed

Wilhelm, Marianne; Bir, Cynthia

2008-01-15

In today's law enforcement community, one of the most vital tools an officer can possess is personal body armor. However, a recent Department of Justice investigation has raised important questions regarding the protection actually afforded officers through the use of personal body armor, and the current test methods used to assess the armor. Test results show that most Zylon-containing vests showed deformations in excess of the 0101.04 Standard's 44 mm backface signature limit. Such increased deformation can lead to serious injuries, including backface signature injuries, which have occurred in the field. Although the vest is successful in containing the round, it is not effectively dissipating the energy enough to prevent large amounts of vest deformation at the area of impact. Therefore, open, penetrating wounds occur even though the bullet did not penetrate the vest. The objective of the current study was to further define the backface signature injury through the use of case studies and laboratory experiments. Following the case study investigation, backface signature testing was conducted using a clay medium based on the NIJ 0101.04 Standard. The final component of this research involved the use of post-mortem human specimens (PMHS) for further investigation of the backface signature injury. Although the underlying cause of backface signature injuries is unknown, energy density is likely to play a role in the mechanism. Energy density (E/a) is defined as the energy per unit area and has been previously used in less lethal skin penetration research. Further research into the underlying causes of backface signature injuries is necessary. In addition to armor testing, the study of law enforcement personnel who have been shot while wearing soft body armor is also a valuable tool for determining the effectiveness of certification standards. Finally, it is important for medical personnel to recognize the backface signature injury and document this as a type of injury separate from blunt trauma or penetrating trauma behind armor injuries. Detailed knowledge of the injury, including the depth of the wound, would be beneficial to the scientific community.

Light Armored Vehicles in Operations Other Than War

DTIC Science & Technology

2002-05-01

8Kenneth W. Estes, Marines Under Armor (Annapolis, MD: Naval Institute Press, 2000), 212. 6 attach and detach elements in task organizing for a...operations. Kenneth W. Estes writes in his book Marines Under Armor : “The light armored vehicles of the LAR battalions, by contrast [to tanks], continue...Martin’s Press, 1991. Estes, Kenneth W., Marines under Armor : The Marine Corps and the Armored Fighting Vehicle. 1916-2000. Annapolis, Maryland: Naval

From National Defense Stockpile (NDS) to Strategic Materials Security Program (SMSP): Evidence and Analytic Support. Volume 1

DTIC Science & Technology

2010-05-01

textiles include “soft” body armor; spall liners for combat vehicles; flame protection garments; and protective braided sleeves for hoses and cable...summarizes the results of an Interim Base Case analysis of those materials as well. Chapter Four offers IDA’s initial ideas regarding opportunities that...process in the requirements analysis process by which the department determines the NDS goals, or stockpile requirements, it will recommend to the

Pathological Gambling in Parkinson's Disease: autonomic measures and impaired decision-making.

PubMed

Angioletti, Laura; Siri, Chiara; Meucci, Nicoletta; Pezzoli, Gianni; Balconi, Michela

2018-06-11

According to the somatic marker hypothesis, autonomic measures and arousal modulation can reveal a difference in subgroups of patients developing impaired decision-making because of addictions. Previously, Pathological Gambling (PG) and Parkinson's Disease (PD) have been associated with differential arousal levels during gambling behavior. However, no research considered the specific autonomic responses of Parkinson's Disease patients with pathological gambling and with a previous history of gambling. Thus, this study investigated Skin Conductance Responses (SCRs), Skin Conductance Level (SCL) and Heart Rate (HR) during the Iowa Gambling Task (IGT) in two groups of PD patients with gambling disorder, active (PD Gamblers; n=14) or remitted (PD Non-Gamblers; n=13) and a control group of patients with Parkinson's Disease only (n=13). Anticipatory autonomic responses to Disadvantageous Decks and Advantageous Decks during the Iowa Gambling Task were measured for each participant. The PD Gamblers group performed worse than the PD Non-Gamblers and the control groups at the IGT task and exhibited lower SCRs, SCL and HR during the decision-making processing of cards belonging to disadvantageous decks. The role of autonomic and behavioral measures was considered This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

General view of the mid deck of the Orbiter Discovery ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General view of the mid deck of the Orbiter Discovery during pre-launch preparations. Note the payload and mission specialists seats. The seats are removed packed and stowed during on-orbit activities. Also not the black panels in the right of the image, they are protective panels used for preparation of the orbiter and astronaut ingress while the orbiter is in its vertical launch position. This image was taken at Kenney Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Service Modules for Coal Extraction

NASA Technical Reports Server (NTRS)

Gangal, M. D.; Lewis, E. V.

1985-01-01

Service train follows group of mining machines, paying out utility lines as machines progress into coal face. Service train for four mining machines removes gases and coal and provides water and electricity. Flexible, coiling armored carriers protect cables and hoses. High coal production attained by arraying row of machines across face, working side by side.

29 CFR 801.14 - Exemption for employers providing security services.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... For example, a security system specially designed to protect diamonds kept in a home vault of a... general prohibition against polygraph tests for certain armored car, security alarm, and security guard..., 801.24, 801.25, 801.26, and 801.35 of this part, section 7(e) permits the use of polygraph tests on...

29 CFR 801.14 - Exemption for employers providing security services.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... For example, a security system specially designed to protect diamonds kept in a home vault of a... general prohibition against polygraph tests for certain armored car, security alarm, and security guard..., 801.24, 801.25, 801.26, and 801.35 of this part, section 7(e) permits the use of polygraph tests on...

30 CFR 75.802 - Protection of high-voltage circuits extending underground.

Code of Federal Regulations, 2010 CFR

2010-07-01

... serve as a grounding conductor for the frames of all high-voltage equipment supplied power from that... stationary electric equipment if: (1) Such circuits are either steel armored or installed in grounded, rigid steel conduit throughout their entire length; or, (2) The voltage of such circuits is nominally 2,400...

30 CFR 75.802 - Protection of high-voltage circuits extending underground.

Code of Federal Regulations, 2011 CFR

2011-07-01

... serve as a grounding conductor for the frames of all high-voltage equipment supplied power from that... stationary electric equipment if: (1) Such circuits are either steel armored or installed in grounded, rigid steel conduit throughout their entire length; or, (2) The voltage of such circuits is nominally 2,400...

Enduring Engagement Yes, Episodic Engagement No: Lessons for SOF from Mali

DTIC Science & Technology

2013-12-01

ammunition cans. Even the non- rusted ammunition failed to reliably ignite due to prolonged exposure to the elements. 59 Weapons in Mali fall under the...In the personnel protection category, body armor for the unit was cut to fifty pieces— barley enough for a third of the ground element. Examples such

Transient sheath overvoltages in armored power cables

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gustavsen, B.; Sletbak, J.

1996-07-01

This paper is concerned with methods of limiting the build-up of transient voltages between sheath and armor in long armored power cables. Calculations by a frequency dependent cable model demonstrate that this voltage can be efficiently limited to an acceptable level by introducing sheath-armor bondings at regular intervals, or by using a semiconductive sheath-armor interlayer. The paper investigates the required minimum length between bondings, as well as the required conductivity of the sheath-armor interlayer if the use of bondings is to be avoided.

The Need to Mobilize Armor in Afghanistan

DTIC Science & Technology

2009-02-20

success. 1 Kenneth W. Estes, Marines Under Armor (Naval Institute Press,2000)34 2 Increasing Combat...4 Kenneth W. Estes, Marines Under Armor (Naval Institute Press,2000) 202 5 Kenneth W. Estes, Marines Under ... Armor (Naval Institute Press,2000) 198- 202 6 Kenneth W. Estes, Marines Under Armor (Naval Institute Press,2000) 203 8 mechanized unit was needed to

48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

Code of Federal Regulations, 2012 CFR

2012-10-01

... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and armor...

48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

Code of Federal Regulations, 2010 CFR

2010-10-01

... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and armor...

48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

Code of Federal Regulations, 2014 CFR

2014-10-01

... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and armor...

48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

Code of Federal Regulations, 2013 CFR

2013-10-01

... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and armor...

48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and armor...

46 CFR 181.320 - Fire hoses and nozzles.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Fire hoses and nozzles. 181.320 Section 181.320 Shipping...) FIRE PROTECTION EQUIPMENT Fire Main System § 181.320 Fire hoses and nozzles. (a) A fire hose with a... cargo decks, where no protection is provided, hoses may be temporarily removed during heavy weather or...

46 CFR 181.320 - Fire hoses and nozzles.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Fire hoses and nozzles. 181.320 Section 181.320 Shipping...) FIRE PROTECTION EQUIPMENT Fire Main System § 181.320 Fire hoses and nozzles. (a) A fire hose with a... cargo decks, where no protection is provided, hoses may be temporarily removed during heavy weather or...

46 CFR 181.320 - Fire hoses and nozzles.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Fire hoses and nozzles. 181.320 Section 181.320 Shipping...) FIRE PROTECTION EQUIPMENT Fire Main System § 181.320 Fire hoses and nozzles. (a) A fire hose with a... cargo decks, where no protection is provided, hoses may be temporarily removed during heavy weather or...

46 CFR 181.320 - Fire hoses and nozzles.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Fire hoses and nozzles. 181.320 Section 181.320 Shipping...) FIRE PROTECTION EQUIPMENT Fire Main System § 181.320 Fire hoses and nozzles. (a) A fire hose with a... cargo decks, where no protection is provided, hoses may be temporarily removed during heavy weather or...

Evaluation of several types of curing and protective materials for concrete : final report on part II : installation report and initial condition survey of bridge decks.

DOT National Transportation Integrated Search

1970-01-01

Thirty-nine test panels were installed on three interstate bridges to evaluate several combinations of curing and protective treatments for concrete. Panels were cured with white pigmented liquid membrane and white polyethylene, both with and without...

Shock destruction armor system

DOEpatents

Froeschner, Kenneth E.

1993-01-01

A shock destruction armor system is constructed and arranged to destroy the force of impact of a projectile by shock hydrodynamics. The armor system is designed to comprise a plurality of superimposed armor plates each preferably having a thickness less than five times the projectile's diameter and are preferably separated one-from-another by a distance at least equal to one-half of the projectile's diameter. The armor plates are effective to hydrodynamically and sequentially destroy the projectile. The armor system is particularly adapted for use on various military vehicles, such as tanks, aircraft and ships.

High levels of exotic armored scales on imported avocados raise concerns regarding USDA-APHIS' phytosanitary risk assessment.

PubMed

Morse, J G; Rugman-Jones, P F; Watson, G W; Robinson, L J; Bi, J L; Stouthamer, R

2009-06-01

Between 1914 and 2007, a quarantine protected California avocado, Persea americana Mill., groves from pests that might be introduced into the state along with fresh, imported avocados. Soon after Mexican avocados were first allowed entry on 1 February 2007, live specimens of several species of armored scales (Hemiptera: Diaspididae) not believed to be present in California were detected on 'Hass' avocados entering the state from Mexico. Initially, the California Department of Food and Agriculture (CDFA) prevented avocados infested with these scales from entering the state or required that they be fumigated with an approved treatment such as methyl bromide. After a Science Advisory Panel meeting in May 2007, U.S. Department of Agriculture-Animal and Plant Health Inspection Service (USDA-APHIS) reaffirmed its position that armored scales on shipments of fruit for consumption (including avocados) pose a "low risk" for pest establishment. In compliance with APHIS protocols, as of 18 July 2007, CDFA altered its policy to allow shipments of scale-infested avocados into the state without treatment. Here, we report on sampling Mexican avocados over an 8-mo period, September 2007-April 2008. An estimated 67 million Mexican Hass avocados entered California over this period. Based on samples from 140 trucks containing approximately 15.6% of this volume of fruit, we estimate that approximately 47.6 million live, sessile armored scales and an additional 20.1 million live eggs and crawlers were imported. We found eight probable species of armored scales in the samples, seven of these are not believed to occur in California; 89.3% of the live scales were Abgrallaspis aguacatae Evans, Watson and Miller, a recently described species. In contrast to the USDA-APHIS opinion, we believe the volume of shipments and levels of live scales they contain present a significant risk to California's US$300 million avocado industry and to other crops that might become infested by one or more of these exotic species.

Assessing behind armor blunt trauma (BABT) under NIJ standard-0101.04 conditions using human torso models.

PubMed

Merkle, Andrew C; Ward, Emily E; O'Connor, James V; Roberts, Jack C

2008-06-01

Although soft armor vests serve to prevent penetrating wounds and dissipate impact energy, the potential of nonpenetrating injury to the thorax, termed behind armor blunt trauma, does exist. Currently, the ballistic resistance of personal body armor is determined by impacting a soft armor vest over a clay backing and measuring the resulting clay deformation as specified in National Institute of Justice (NIJ) Standard-0101.04. This research effort evaluated the efficacy of a physical Human Surrogate Torso Model (HSTM) as a device for determining thoracic response when exposed to impact conditions specified in the NIJ Standard. The HSTM was subjected to a series of ballistic impacts over the sternum and stomach. The pressure waves propagating through the torso were measured with sensors installed in the organs. A previously developed Human Torso Finite Element Model (HTFEM) was used to analyze the amount of tissue displacement during impact and compared with the amount of clay deformation predicted by a validated finite element model. All experiments and simulations were conducted at NIJ Standard test conditions. When normalized by the response at the lowest threat level (Level I), the clay deformations for the higher levels are relatively constant and range from 2.3 to 2.7 times that of the base threat level. However, the pressures in the HSTM increase with each test level and range from three to seven times greater than Level I depending on the organ. The results demonstrate the abilities of the HSTM to discriminate between threat levels, impact conditions, and impact locations. The HTFEM and HSTM are capable of realizing pressure and displacement differences because of the level of protection, surrounding tissue, and proximity to the impact point. The results of this research provide insight into the transfer of energy and pressure wave propagation during ballistic impacts using a physical surrogate and computational model of the human torso.

Use of Body Armor Protection Levels with Squad Automatic Weapon Fighting Load Impacts Soldier Performance, Mobility, and Postural Control

DTIC Science & Technology

2015-05-01

changes have been historically seen with the heavier approach march load between 21 kg and 33 kg (Schiffman et al., 2006, and Harman et al., 1999) or...the heaviest emergency approach march load greater than 32 kg (Attwells et al., 2006, and Harman et al., 1999). Increasing ballistic protection...vital to maintaining upright posture while walking ( Harman et al., 1999). Alterations made lower in the kinematic chain, such as the hip flexion

Meteoroid Protection Methods for Spacecraft Radiators Using Heat Pipes

NASA Technical Reports Server (NTRS)

Ernst, D. M.

1979-01-01

Various aspects of achieving a low mass heat pipe radiator for the nuclear electric propulsion spacecraft were studied. Specific emphasis was placed on a concept applicable to a closed Brayton cycle power sub-system. Three aspects of inter-related problems were examined: (1) the armor for meteoroid protection, (2) emissivity of the radiator surface, and (3) the heat pipe itself. The study revealed several alternatives for the achievement of the stated goal, but a final recommendation for the best design requires further investigation.

46 CFR 56.50-70 - Gasoline fuel systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

.... (1) Fuel supply piping to the engines shall be of seamless drawn annealed copper pipe or tubing... sharp edges. Where passing through steel decks or bulkheads, fuel lines shall be protected by close...

46 CFR 56.50-70 - Gasoline fuel systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

.... (1) Fuel supply piping to the engines shall be of seamless drawn annealed copper pipe or tubing... sharp edges. Where passing through steel decks or bulkheads, fuel lines shall be protected by close...

46 CFR 56.50-70 - Gasoline fuel systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... (1) Fuel supply piping to the engines shall be of seamless drawn annealed copper pipe or tubing... sharp edges. Where passing through steel decks or bulkheads, fuel lines shall be protected by close...

46 CFR 56.50-70 - Gasoline fuel systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

.... (1) Fuel supply piping to the engines shall be of seamless drawn annealed copper pipe or tubing... sharp edges. Where passing through steel decks or bulkheads, fuel lines shall be protected by close...

46 CFR 56.50-70 - Gasoline fuel systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... (1) Fuel supply piping to the engines shall be of seamless drawn annealed copper pipe or tubing... sharp edges. Where passing through steel decks or bulkheads, fuel lines shall be protected by close...

46 CFR 127.220 - General fire protection.

Code of Federal Regulations, 2013 CFR

2013-10-01

... of and insulated from woodwork and other combustible matter. (c) Paint lockers and similar... ventilated battery locker that— (1) Is located above the main deck; (2) Is located in the open; and (3) Has...

46 CFR 127.220 - General fire protection.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of and insulated from woodwork and other combustible matter. (c) Paint lockers and similar... ventilated battery locker that— (1) Is located above the main deck; (2) Is located in the open; and (3) Has...

46 CFR 127.220 - General fire protection.

Code of Federal Regulations, 2012 CFR

2012-10-01

... of and insulated from woodwork and other combustible matter. (c) Paint lockers and similar... ventilated battery locker that— (1) Is located above the main deck; (2) Is located in the open; and (3) Has...

46 CFR 127.220 - General fire protection.

Code of Federal Regulations, 2014 CFR

2014-10-01

... of and insulated from woodwork and other combustible matter. (c) Paint lockers and similar... ventilated battery locker that— (1) Is located above the main deck; (2) Is located in the open; and (3) Has...

46 CFR 127.220 - General fire protection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... of and insulated from woodwork and other combustible matter. (c) Paint lockers and similar... ventilated battery locker that— (1) Is located above the main deck; (2) Is located in the open; and (3) Has...

Closeup view of the Pilot's Seat on the Flight Deck ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Close-up view of the Pilot's Seat on the Flight Deck of the Orbiter Discovery. It appears the Orbiter is in the roll out / launch pad configuration. A protective cover is over the Rotational Hand Controller to protect it during the pilot's ingress. Control panels R1 and R2 are prominent in this view. Panel R1 has switches for control and maintenance of on-board cryogenics for the fuel cells among other functions and panel R2 has switches and controls for the Auxiliary Power Units, ET umbilical doors as well as other operational controls. Note the portable fire extinguisher in the lower right corner of the image. This photograph was taken at Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Metallized coatings for corrosion control of Naval ship structures and components

NASA Technical Reports Server (NTRS)

1983-01-01

In attempting to improve corrosion control, the U.S. Navy has undertaken a program of coating corrosion-susceptible shipboard components with thermally sprayed aluminum. In this report the program is reviewed in depth, including examination of processes, process controls, the nature and properties of the coatings, nondestructive examination, and possible hazards to personnel. The performance of alternative metallic coating materials is also discussed. It is concluded that thermally sprayed aluminum can provide effective long-term protection against corrosion, thereby obviating the need for chipping of rust and repainting by ship personnel. Such coatings are providing excellent protection to below-deck components such as steam valves, but improvements are needed to realize the full potential of coatings for above-deck service. Several recommendations are made regarding processes, materials, and research and development aimed at upgrading further the performance of these coatings.

Ballistic Testing for Interceptor Body Armor Inserts Needs Improvement

DTIC Science & Technology

2011-08-01

030, “Ballistic Testing and Product Quality Surveillance for the Interceptor Body Armor - Vest Components Need Improvement,” January 3, 2011. This...Body Armor Ballistic Inserts Interceptor Body Armor (IBA) is a modular body armor system that consists of an outer tactical vest , ballistic inserts...altitude tests was because the ceramic ballistic inserts are solid structures that are not sensitive to reduced pressure and moisture. PM SEQ offered no

Transparent Armor Cost Benefit Study

DTIC Science & Technology

2007-03-06

Armored HMMWVs (M1114s) 2003 2005 2006 UNCLASSIFIED UNCLASSIFIED 3/6/2007 4/17 2006 “Iraqi Pope Glass” 2004-2005 - GPK Recent HistoryEarly OIF Curb Wt...10,300lbs GVW: 12,100lbs UNCLASSIFIED UNCLASSIFIED 3/6/2007 5/17 Future Transparent Gun Shields Requirement: Upgrade GPKS with transparent armor for...enhanced situational awareness while maintaining soldier cover within armor envelope. AHI GS & GPK Upgraded Gunner Shield – Transparent Armored Gun

46 CFR 34.10-10 - Fire station hydrants, hose and nozzles-T/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... must be located to afford protection from heavy seas. The hose must be stored in a location that is... metal. Couplings shall either: (1) Use National Standard fire hose coupling threads for the 11/2 inch... shall be connected to outlets at all times. However, in heavy weather on open decks where no protection...

46 CFR 173.020 - Intact stability standards: Counterballasted and non-counterballasted vessels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... not heel beyond the limits specified in paragraph (d) of this section: (1) Beam to depth—3.40 to 4.75...) of this section, the following limits of heel apply with the vessel at its deepest operating draft: (1) Protected and partially protected waters and Great Lakes in summer—heel to main deck immersion or...

46 CFR 173.020 - Intact stability standards: Counterballasted and non-counterballasted vessels.

Code of Federal Regulations, 2011 CFR

2011-10-01

... not heel beyond the limits specified in paragraph (d) of this section: (1) Beam to depth—3.40 to 4.75...) of this section, the following limits of heel apply with the vessel at its deepest operating draft: (1) Protected and partially protected waters and Great Lakes in summer—heel to main deck immersion or...

Study on the Feasibility of Mass Area Ordnance Decontamination

DTIC Science & Technology

1974-08-15

and Armor Plate Protection 11-50 11-20 Bucket Modifications 11-53 Appendices Figure Page III-1 The Relationship Between Rippability and Seismic...FK S. .. . ... L, i ! ,, ,,i , , W~AM0RPHIC ROK MINERALS 9 ORESm n, imI I’𔄃 1.. I 1. 1 .t’ I.* [ FIGURE III-l: The Relationship Between Rippability

Ballistic Testing and Product Quality Surveillance for the Interceptor Body Armor - Vest Components Need Improvement

DTIC Science & Technology

2011-01-03

six contracts. Interceptor Body Armor – Vest Components IBA is a modular body armor system that consists of an OTV, ceramic plates , and components...Armor - Vest Components Need Improvement Report Documentation Page Form ApprovedOMB No. 0704-0188 Public reporting burden for the...Ballistic Testing and Product Quality Surveillance for the Interceptor Body Armor - Vest Components Need Improvement 5a. CONTRACT NUMBER 5b. GRANT

Fracture of Rolled Homogeneous Steel Armor (Nucleation Threshold Stress).

DTIC Science & Technology

1980-01-01

AD-AO81 618 ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND ABERD--ETC F/B 19/4 FRACTURE OF ROLLED HOMOGENEOUS STEEL ARMOR (NUCLEATION THRESHOL--ETC(U...ARBRL-MR-02984A QQ FRACTURE OF ROLLED HOMOGENEOUS STEEL ARMOR (NUCLEATION THRESHOLD STRESS) Gerald L Moss Lynn SeamanLy~ S, ,.DTIC S ELECTED January...nucleation stress, Crack threshold stress, Fracture, Fracture stress, Spallation, Armor, Rolled homogeneous steel armor M~ AS$TRACr (Vita ssf -- ebb

Heavy Wrought Armor Metallurgical Evaluation of Commercially Produced Heavy Wrought Armor to Improve the Specification Requirements

DTIC Science & Technology

1948-02-02

Armor, Steel , Wrought, Over 4" WAL Project No.: 8.11-G TITLE HEAVY WROUGHT ARMOR Metallurgical Evaluation of Commercially Produced * . Heavy Wrought...Tentative Specification AXS-1803 Armor Plate: Steel , Wrought, Homogeneous (4" to 1211 inclusive). The results of the investi- gation indicated the...Plate: Steel , Wrought, Homogeneous (4" to 12" inclusive)". .’o* -... . . . . .’"-’ ."-. - -- -" - -"-. ."-. 2

2009 Combat Vehicles Conference (BRIEFING CHARTS)

DTIC Science & Technology

2009-10-14

Strategy to Field 531 Systems Targeting Under Armor and FS3 Integration on A3 BFIST on the Move Our #1 Priority is to Support Units Engaged in O C i...Armored Knight Program • Targeting Under Armor /On the Move effort underway to • The M1200 Armored Knight provides increase survivability of...increased survivability Sustainment Survivability 32 10/13/2009 BFIST Program Overview • Targeting Under Armor /On the Move effort underway to

Palapa-B communications satellite launched from the Shuttle Challenger

NASA Image and Video Library

1983-06-24

S83-35764 (19 June 1983) --- The Indonesian Palapa B communications satellite is just about to clear the vertical stabilizer of the Earth-orbiting Space Shuttle Challenger to begin its way toward its Earth-orbital destination. Also visible in this 70mm exposure, photographed through the flight deck?s aft windows, are the Shuttle pallet satellite, the experiment package for NASA?s office of space and terrestrial applications (OSTA-2), the now vacated protective cradles for Palapa and Telesat Canada?s Anik C2 satellites, some getaway special (GAS) canisters and the Canadian-built remote manipulator system (RMS) arm.

Assessing behind armor blunt trauma in accordance with the National Institute of Justice Standard for Personal Body Armor Protection using finite element modeling.

PubMed

Roberts, Jack C; Ward, Emily E; Merkle, Andrew C; O'Connor, James V

2007-05-01

To assess the possibility of injury as a result of behind armor blunt trauma (BABT), a study was undertaken to determine the conditions necessary to produce the 44-mm clay deformation as set forth in the National Institute of Justice (NIJ) Standard 0101.04. These energy levels were then applied to a three-dimensional Human Torso Finite Element Model (HTFEM) with soft armor vest. An examination will be made of tissue stresses to determine the effects of the increased kinetic energy levels on the probability of injury. A clay finite element model (CFEM) was created with a material model that required nonlinear properties for clay. To determine these properties empirically, the results from the CFEM were matched with experimental drop tests. A soft armor vest was modeled over the clay to create a vest over clay block finite element model (VCFEM) and empirical methods were again used to obtain material properties for the vest from experimental ballistic testing. Once the properties for the vest and clay had been obtained, the kinetic energy required to produce a 44-mm deformation in the VCFEM was determined through ballistic testing. The resulting kinetic energy was then used in the HTFEM to evaluate the probability of BABT. The VCFEM, with determined clay and vest material properties, was exercised with the equivalent of a 9-mm (8-gm) projectile at various impact velocities. The 44-mm clay deformation was produced with a velocity of 785 m/s. This impact condition (9-mm projectile at 785 m/s) was used in ballistic exercises of the HTFEM, which was modeled with high-strain rate human tissue properties for the organs. The impact zones were over the sternum anterior to T6 and over the liver. The principal stresses in both soft and hard tissue at both locations exceeded the tissue tensile strength. This study indicates that although NIJ standard 0101.04 may be a good guide to soft armor failure, it may not be as good a guide in BABT, especially at large projectile kinetic energies. Further studies, both numerical and experimental, are needed to assist in predicting injury using the NIJ standard.

76 FR 27355 - 2011 National Institute of Justice Body Armor Workshop

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-11

... Institute of Justice Body Armor Workshop AGENCY: National Institute of Justice, DOJ. ACTION: Notice of Meeting of the 2011 NIJ Body Armor Workshop. SUMMARY: The National Institute of Justice invites manufacturers of ballistic-resistant body armor, ballistic laboratory testing facilities and other interested...

27 CFR 478.148 - Armor piercing ammunition intended for sporting or industrial purposes.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Armor piercing ammunition... AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.148 Armor piercing ammunition intended for sporting or industrial purposes. The Director may exempt certain armor piercing...

27 CFR 478.148 - Armor piercing ammunition intended for sporting or industrial purposes.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Armor piercing ammunition... AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.148 Armor piercing ammunition intended for sporting or industrial purposes. The Director may exempt certain armor piercing...

27 CFR 478.148 - Armor piercing ammunition intended for sporting or industrial purposes.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Armor piercing ammunition... AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.148 Armor piercing ammunition intended for sporting or industrial purposes. The Director may exempt certain armor piercing...

27 CFR 478.148 - Armor piercing ammunition intended for sporting or industrial purposes.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Armor piercing ammunition... AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.148 Armor piercing ammunition intended for sporting or industrial purposes. The Director may exempt certain armor piercing...

46 CFR 111.05-7 - Armored and metallic sheathed cable.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Armored and metallic sheathed cable. 111.05-7 Section 111.05-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING... Armored and metallic sheathed cable. When installed, the metallic armor or sheath must meet the...

46 CFR 111.05-7 - Armored and metallic sheathed cable.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Armored and metallic sheathed cable. 111.05-7 Section 111.05-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING... Armored and metallic sheathed cable. When installed, the metallic armor or sheath must meet the...

46 CFR 111.05-7 - Armored and metallic sheathed cable.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Armored and metallic sheathed cable. 111.05-7 Section 111.05-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING... Armored and metallic sheathed cable. When installed, the metallic armor or sheath must meet the...

46 CFR 111.05-7 - Armored and metallic sheathed cable.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Armored and metallic sheathed cable. 111.05-7 Section 111.05-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING... Armored and metallic sheathed cable. When installed, the metallic armor or sheath must meet the...

46 CFR 111.05-7 - Armored and metallic sheathed cable.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Armored and metallic sheathed cable. 111.05-7 Section 111.05-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING... Armored and metallic sheathed cable. When installed, the metallic armor or sheath must meet the...

7 CFR 1755.406 - Shield or armor ground resistance measurements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Shield or armor ground resistance measurements. 1755... MATERIALS, AND STANDARD CONTRACT FORMS § 1755.406 Shield or armor ground resistance measurements. (a) Shield or armor ground resistance measurements shall be made on completed lengths of copper cable and wire...

7 CFR 1755.406 - Shield or armor ground resistance measurements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 11 2011-01-01 2011-01-01 false Shield or armor ground resistance measurements. 1755... MATERIALS, AND STANDARD CONTRACT FORMS § 1755.406 Shield or armor ground resistance measurements. (a) Shield or armor ground resistance measurements shall be made on completed lengths of copper cable and wire...

Power Projection: The Current and Future Relevance of the M1A1Tank to Marine Corps Capabilities

DTIC Science & Technology

2002-01-01

Kenneth W. Estes, Marines under Armor : The Marine Corps and the Armored Fighting Vehicle, 1916-2000 (Annapolis, MD: Naval institute Press, 2000), 183...is the M2 heavy barrel machine gun that has been in the U.S. inventory for decades. It can be fired from under armor and has a range of 1800 meters...Accessed 9 January 2002. Estes, Kenneth W. Marines under Armor : The Marine Corps and the Armored Fighting Vehicle, 1916-2000. Annapolis, MD

Protection of structural concrete substructures.

DOT National Transportation Integrated Search

1992-12-01

The corrosion of reinforcing steel within concrete has always been a problem in construction of bridge decks. With low slump concrete and epoxy rebar, progress has been made in controlling the corrosion. There is concern, however, that the chloride a...

46 CFR 194.05-7 - Explosives-Detail requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Stowage shall be in a location reasonably protected from the full force of boarding seas. (2) Stowage... shall not be on or under the bridge, or navigating deck, or within a distance, in a horizontal plane, of...

46 CFR 194.05-7 - Explosives-Detail requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Stowage shall be in a location reasonably protected from the full force of boarding seas. (2) Stowage... shall not be on or under the bridge, or navigating deck, or within a distance, in a horizontal plane, of...

46 CFR 194.05-7 - Explosives-Detail requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Stowage shall be in a location reasonably protected from the full force of boarding seas. (2) Stowage... shall not be on or under the bridge, or navigating deck, or within a distance, in a horizontal plane, of...

46 CFR 194.05-7 - Explosives-Detail requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Stowage shall be in a location reasonably protected from the full force of boarding seas. (2) Stowage... shall not be on or under the bridge, or navigating deck, or within a distance, in a horizontal plane, of...

High Expansion Foam for Protecting Large Volume Mission Critical Shipboard Spaces

DTIC Science & Technology

2009-01-01

aqueous film - forming foam ( AFFF ) sprinklers designed only to combat Class B two-dimensional pool fires.1 The...Validation Tests, Series 1 – An Evaluation of Aqueous Film Foaming Foam ( AFFF ) Suppression Systems for Protection of LHA(R) Well Deck and Vehicle... firefighting system design. NRL further recognized that employing a traditional high expansion foam generator would impact shipboard

Analysis of Thick Sandwich Shells with Embedded Ceramic Tiles

NASA Technical Reports Server (NTRS)

Davila, Carlos G.; Smith, C.; Lumban-Tobing, F.

1996-01-01

The Composite Armored Vehicle (CAV) is an advanced technology demonstrator of an all-composite ground combat vehicle. The CAV upper hull is made of a tough light-weight S2-glass/epoxy laminate with embedded ceramic tiles that serve as armor. The tiles are bonded to a rubber mat with a carefully selected, highly viscoelastic adhesive. The integration of armor and structure offers an efficient combination of ballistic protection and structural performance. The analysis of this anisotropic construction, with its inherent discontinuous and periodic nature, however, poses several challenges. The present paper describes a shell-based 'element-layering' technique that properly accounts for these effects and for the concentrated transverse shear flexibility in the rubber mat. One of the most important advantages of the element-layering technique over advanced higher-order elements is that it is based on conventional elements. This advantage allows the models to be portable to other structural analysis codes, a prerequisite in a program that involves the computational facilities of several manufacturers and government laboratories. The element-layering technique was implemented into an auto-layering program that automatically transforms a conventional shell model into a multi-layered model. The effects of tile layer homogenization, tile placement patterns, and tile gap size on the analysis results are described.

Innovative 3D Textile Structures for Soft Body Armor Protection: The EPIDARM Project

NASA Astrophysics Data System (ADS)

Maillet, Jérôme; Lefebvre, Marie; Boussu, François; Pirlot, Marc

There is a real need for battlefield soldiers to be protected from ­ballistic and CBRNE threats and also to be in permanent contact and localization with the logistic support of the commander. Ballistic, CBRNE and tactical jackets are currently three different components, developed separately and worn on top of each other. One of the EPIDARM project's targets is to propose a personal protection demonstration for the optimal system configuration in order to reduce the cost and weight while improving protection. The systems approach used for the EPIDARM program considers the protective system inside its environment (threat, the wearer - generic soldier, task and climates). The latest emergent technologies in ballistic and CBRN protection, ergonomic effectiveness and financial cost are considered and help to select final solutions.

Baseline UT Measurements for Armor Inspection

NASA Astrophysics Data System (ADS)

Margetan, Frank J.; Richter, Nate; Barnard, Dan; Hsu, David; Gray, Tim; Brasche, Lisa; Bruce Thompson, R.

2010-02-01

Some prototype armor panels are fabricated from several layers of dissimilar material bonded together. These may include ceramics, graphite composites, fiberglass composites and rubber. The ultrasonic properties of these layers influence inspections for armor defects. In this paper we describe measurements of ultrasonic velocity, attenuation, sound beam distortion and signal fluctuations for the individual layers comprising one armor prototype. We then discuss how knowledge of these properties can be used when choosing an optimum frequency for an ultrasonic pitch/catch immersion inspection. In our case an effective inspection frequency near 1.5 MHz affords: (1) adequate strength of through-transmitted signals in unflawed armor; (2) adequate lateral resolution for detecting small disbonds at interfaces; and (3) low levels of UT signal fluctuations due to the natural inhomogeneity of certain armor layers. The utility of this approach is demonstrated using armor panels containing artificial disbonds at selected interfaces.

Towards Development of a Super Ceramic Composite - Initial Investigation into Improvement of Strength and Toughness of Polycrystalline Ceramics

DTIC Science & Technology

2012-08-01

sintering of SiC. James Lill (2010) evaluated the Reactive Empirical Bond Order potentials of Brenner (Brenner 1990); the Adaptive Intermolecular Reactive...Protection mechanisms of the iron-plated armor of a deep-sea hydrothermal vent gastropod . PNAS 107(3):987-997. Yu, J., S. B. Sinnott, and S. R. Phillpot

Procurement and Delivery of Joint Service Armor Protected Vehicles

DTIC Science & Technology

2009-01-29

veh icle mi x of MRAPs and UA II and their rcspecti ve cfl ’ccts on opcrationaltactics, technique , Md procedurcs, as we ll as vehic le forma ti ons...rcasonablc price compari sons with prior purchases orthe same 01’ similar items made on a competiti ve bas is 0 1’ supported by va lid cost 0 1’ Iri

77 FR 22345 - Agency Information Collection Activities: Proposed Collection; Comments Requested; Body Armor in...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-13

... correctional officers, such as the proportion who have body armor, the rate of use, the decision-making factors... Collection; Comments Requested; Body Armor in Correctional Institutions Survey ACTION: 60-day notice of... Collection: Establishment survey and initial approval of collection. (2) Title of Form/Collection: Body Armor...

Maintaining the Marine Corps’ Tank Dominant Combat Overmatch in an Uncertain Future

DTIC Science & Technology

2012-03-12

Company, 1999), 6. 2 2011 Tank Conference Report. (Dated 02 Feb 2011) 3 Kenneth E. Estes. Marines Under Armor : The Marine Corps and the Armored...Kenneth W. Marines Under Armor : The Marine Corps and the Armored Fighting Vehicle, 1916-2000. Annapolis, MD: Naval Institute Press, 2000. Ford

Skin and scales of teleost fish: Simple structure but high performance and multiple functions

NASA Astrophysics Data System (ADS)

Vernerey, Franck J.; Barthelat, Francois

2014-08-01

Natural and man-made structural materials perform similar functions such as structural support or protection. Therefore they rely on the same types of properties: strength, robustness, lightweight. Nature can therefore provide a significant source of inspiration for new and alternative engineering designs. We report here some results regarding a very common, yet largely unknown, type of biological material: fish skin. Within a thin, flexible and lightweight layer, fish skins display a variety of strain stiffening and stabilizing mechanisms which promote multiple functions such as protection, robustness and swimming efficiency. We particularly discuss four important features pertaining to scaled skins: (a) a strongly elastic tensile behavior that is independent from the presence of rigid scales, (b) a compressive response that prevents buckling and wrinkling instabilities, which are usually predominant for thin membranes, (c) a bending response that displays nonlinear stiffening mechanisms arising from geometric constraints between neighboring scales and (d) a robust structure that preserves the above characteristics upon the loss or damage of structural elements. These important properties make fish skin an attractive model for the development of very thin and flexible armors and protective layers, especially when combined with the high penetration resistance of individual scales. Scaled structures inspired by fish skin could find applications in ultra-light and flexible armor systems, flexible electronics or the design of smart and adaptive morphing structures for aerospace vehicles.

Field testing and evaluation of a demonstration timber bridge.

DOT National Transportation Integrated Search

2012-02-01

Asphalt wearing surfaces are commonly used on timber bridges with transverse glued-laminated deck panel systems to help protect the timber components. However, poor performance of these asphalt wearing surfaces in the past has resulted in repeated re...

Guardrails for use on historic bridges: volume 2--bridge deck overhang design.

DOT National Transportation Integrated Search

2016-11-01

Bridges that are designated historic present a special challenge to bridge engineers whenever rehabilitation work or improvements are : made to the bridges. Federal and state laws protect historically significant bridges, and railings on these bridge...

Electrically conductive Portland cement concrete.

DOT National Transportation Integrated Search

1986-01-01

There is a need for an effective, simple-to-install secondary anode system for use in the cathodic protection of reinforced concrete bridge decks. In pursuit of such a system, carbon fibers and carbon black were incorporated in portland cement concre...

User s Manual for Armor Stone Evaluation Model (ARMOR): Great Lakes Armor Stone Study

DTIC Science & Technology

2015-08-01

Broderick and Ahrens (1982) defined damage to an armor layer by the normalized eroded cross-section area as S = Ae/(Dn50)2, where Ae is the measured...84. Broderick , L., and J. P. Ahrens. 1982. Rip-rap stability scale effects. Technical Paper 82- 3. Vicksburg, MS: U.S. Army Engineer Waterways

Armored Force: The Rapid Development of a Uniquely American Force

DTIC Science & Technology

2010-03-19

tank dominated the Armored Force in 1940. The latest model, the M2A4 , weighed 12 tons and carried a 37mm main gun mounted in a single turret. It also...exploitation phase. Second, armor was concentrated in sufficient mass at the point of the breakthrough. This enabled the armored units to blast their

Tanks Within The Marine Air Ground Task Force: A N/A Versatile Combat Multiplier Throughout the Full Spectrum of Operations

DTIC Science & Technology

2010-04-26

Estes, Marines Under Armor : The Marine Corps and the Armored Fighting Vehicle, 1916- 2000. Naval Institute Press, Annapolis MD, 2000. Prior to WWIT...Marines Under Armor : The Marine Corps and the Armored Fighting Vehicle, 1916-2000. Naval Institute Press, Annapolis, MA: 2000 Gilbert, Oscar E

Nuclear Medical Science Officers: Army Health Physicists Serving and Defending Their Country Around the Globe

NASA Astrophysics Data System (ADS)

Melanson, Mark; Bosley, William; Santiago, Jodi; Hamilton, Daniel

2010-02-01

Tracing their distinguished history back to the Manhattan Project that developed the world's first atomic bomb, the Nuclear Medical Science Officers are the Army's experts on radiation and its health effects. Serving around the globe, these commissioned Army officers serve as military health physicists that ensure the protection of Soldiers and those they defend against all sources of radiation, military and civilian. This poster will highlight the various roles and responsibilities that Nuclear Medical Science Officers fill in defense of the Nation. Areas where these officers serve include medical health physics, deployment health physics, homeland defense, emergency response, radiation dosimetry, radiation research and training, along with support to the Army's corporate radiation safety program and international collaborations. The poster will also share some of the unique military sources of radiation such as depleted uranium, which is used as an anti-armor munition and in armor plating because of its unique metallurgic properties. )

Closeup view of the upper exterior of the forward fuselage ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Close-up view of the upper exterior of the forward fuselage of the Orbiter Discovery in the Orbiter Processing Facility at NASA's Kennedy Space Center. The view show a detail of the flight deck windows with protective covers installed to protect the window surfaces during processing. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

A computational analysis of the ballistic performance of light-weight hybrid composite armors

NASA Astrophysics Data System (ADS)

Grujicic, M.; Pandurangan, B.; Koudela, K. L.; Cheeseman, B. A.

2006-11-01

The ability of hybrid light-weight fiber-reinforced polymer-matrix composite laminate armor to withstand the impact of a fragment simulating projectile (FSP) is investigated using a non-linear dynamics transient computational analysis. The hybrid armor is constructed using various combinations and stacking sequences of a high-strength/high-stiffness carbon fiber-reinforced epoxy (CFRE) and a high-ductility/high-toughness Kevlar fiber-reinforced epoxy (KFRE) composite laminates of different thicknesses. The results obtained indicate that at a fixed thickness of the armor both the stacking sequence and the number of CFRE/KFRE laminates substantially affect the ballistic performance of the armor. Specifically, it is found that the armor consisting of one layer of KFRE and one layer of CFRE, with KFRE laminate constituting the outer surface of the armor, possesses the maximum resistance towards the projectile-induced damage and failure. The results obtained are rationalized using an analysis of the elastic wave reflection and transmission behavior at the inter-laminate and laminate/air interfaces.

First annual report SHRP C103 task 4 : rapid repair techniques.

DOT National Transportation Integrated Search

1989-01-01

The objective of task four is to develop technically and economically feasible methods of concrete bridge deck protection, rehabilitation, and replacement. The objective of the task will be accomplished through a progression of six subtasks. The subt...

Procedures for the evaluation of sheet membrane waterproofing

DOT National Transportation Integrated Search

1999-08-01

Sheet membrane waterproofing has been used to protect bridge decks against water and deicing salts by transportation agencies in New England for more than two decades. Though such membranes have proven useful at extending the useful life of bridge de...

View forward of five inch gun mounted in sponson; note ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View forward of five inch gun mounted in sponson; note glass windows which would be removed in combat, gudgeons below window allowed attachment of armor plate which could be swung up to protect gun crew in battle; also note lower section of flag rack at top left center of photograph. (p39) - USS Olympia, Penn's Landing, 211 South Columbus Boulevard, Philadelphia, Philadelphia County, PA

Virtual Prototyping for Personal Protective Equipment and Workplaces

DTIC Science & Technology

1999-03-01

Basket Weave Kevlar-29 Fabric Loosely Draped over 20% Ordnance Gelatin Block Subject to Non-Perforating Impact by .38 Special (130-grain FMJ...Fabric and fabric-like materials are very difficult to model because of the dynamic properties of folding, draping , and stretching. How these...Targets Bare Targets with Insitu Instrumentation V7 Instrumented Targets with Loosely Draped Clothing SL Instrumented Targets with Body Armor

Assessment of Bridging Requirements and Current Bridging Capabilities for use of Legacy Heavy Forces Inside the Contemporary Operational Environment

DTIC Science & Technology

2003-01-01

vehicle-launched bridge (AVLB), the medium-girder bridge (MGB) and the Ribbon Bridge. The AVLB is capable of crossing 17-meter gaps using a crew under ... armor protection (FM 5-34, 2001). The MGB is capable of crossing single spans of 46.2 meters with the addition of a “link-reinforcement system” that

Plans: Poop Deck, Boat Deck, Housetop, Bridge Deck, Upper Bridge ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Plans: Poop Deck, Boat Deck, Housetop, Bridge Deck, Upper Bridge Deck, Navigating Bridge, Forecastle Deck, Upper Deck, Second Deck and Hold - Saugatuck, James River Reserve Fleet, Newport News, Newport News, VA

Transparent Armor Cost Benefit Study

DTIC Science & Technology

2008-04-01

2005 2006 UNCLASSIFIED UNCLASSIFIED 4/30/2008 4/17 2006 “Iraqi Pope Glass” 2004-2005 - GPK Recent HistoryEarly OIF Curb Wt: 10,300lbs GVW: 12,100lbs...UNCLASSIFIED UNCLASSIFIED 4/30/2008 5/17 Future Transparent Gun Shields Requirement: Upgrade GPKS with transparent armor for enhanced situational...awareness while maintaining soldier cover within armor envelope. AHI GS & GPK Upgraded Gunner Shield – Transparent Armored Gun Shield (TAGS

Transparent Armor Cost Benefit Study

DTIC Science & Technology

2006-10-30

added this cocoon to approximately 100 HMMWVs in Ramadi. 2006 “Iraqi Pope Glass” 2004-2005 - GPK Recent HistoryEarly OIF Curb Wt: 10,300lbs GVW...12,100lbs UNCLASSIFIED UNCLASSIFIED 10/30/2006 5/14 Future Transparent Gun Shields Requirement: Upgrade GPKS with transparent armor for enhanced...situational awareness while maintaining soldier cover within armor envelope. AHI GS & GPK Upgraded Gunner Shield – Transparent Armored Gun Shield (TAGS

Turning the InSight Lander Science Deck

NASA Image and Video Library

2015-05-27

The science deck of NASA's InSight lander is being turned over in this April 29, 2015, photo from InSight assembly and testing operations inside a clean room at Lockheed Martin Space Systems, Denver. The large circular component on the deck is the protective covering to be placed over InSight's seismometer after the seismometer is placed directly onto the Martian ground. InSight, for Interior Exploration Using Seismic Investigations, Geodesy and Heat Transport, is scheduled for launch in March 2016 and landing in September 2016. It will study the deep interior of Mars to advance understanding of the early history of all rocky planets, including Earth. Note: After thorough examination, NASA managers have decided to suspend the planned March 2016 launch of the Interior Exploration using Seismic Investigations Geodesy and Heat Transport (InSight) mission. The decision follows unsuccessful attempts to repair a leak in a section of the prime instrument in the science payload. http://photojournal.jpl.nasa.gov/catalog/PIA19670

Long-term corrosion protection of bridge elements reinforcing materials in concrete : final report.

DOT National Transportation Integrated Search

2017-09-01

Preventing or mitigating the corrosion of reinforcing steel in bridge decks is a major challenge for state transportation agencies. With agency budgets stretched thinner every year, they must implement strategies to extend the service lives of bridge...

Armored Family of Vehicles (AFV). Phase 1 Report. Book 7. Volume 11

DTIC Science & Technology

1987-08-31

Armored Family of Vehicles. Specific requirements and products are described which initiate the training development process and a training management ...approach for the TRADOC and proponent schools to plan, develop, manage and integrate the training subsystem(s) for the Armored Family of Vehicles...Procedures. q. Charter, Armored Family of Vehicles. r. Operational and Organizational (O&W) Plan for AFV. s. System MANPRINT Management Plan for AFV

Ballistic Resistance of Body Armor. NIJ Standard-0101.06

DTIC Science & Technology

2008-07-01

49.2 ft ± 3.28 ft) Length to be adjusted to meet velocity accuracy requirements Test Barrel Armor Panel Backing Material Fixture Start Sensor Set...Systems, Testing and Evaluation Amanda Forster, Materials Research Engineer The preparation of this standard was sponsored by the National...manufacturers seek NIJ compliance of their armor to this standard and the armor contains unique materials or forms of construction that may not have

Computational Study of a Functionally Graded Ceramic-Metallic Armor

DTIC Science & Technology

2006-12-15

UNCLAS –Dist. A - Approved for public release Computational Study of a Functionally Graded Ceramic-Metallic Armor Douglas W. Templeton1, Tara J...efficiency of a postulated FGM ceramic-metallic armor system composed of aluminum nitride (AlN) and aluminum. The study had two primary...2006 2. REPORT TYPE N/ A 3. DATES COVERED - 4. TITLE AND SUBTITLE Computational Study of a Functionally Graded Ceramic-Metallic Armor 5a

Expanding the Availability of Lightweight Aluminum Alloy Armor Plate Procured from Detailed Military Specifications

NASA Astrophysics Data System (ADS)

Doherty, Kevin; Squillacioti, Richard; Cheeseman, Bryan; Placzankis, Brian; Gallardy, Denver

For many years, the range of aluminum alloys for armor plate applications obtainable in accordance with detailed military specifications was very limited. However, the development of improved aluminum alloys for aerospace and other applications has provided an opportunity to modernize the Army portfolio for ground vehicle armor applications. While the benefits of offering additional alloy choices to vehicle designers is obvious, the process of creating detailed military specifications for armor plate applications is not trivial. A significant amount of material and testing is required to develop the details required by an armor plate specification. Due to the vast number of material programs that require standardization and with a limited amount of manpower and funds as a result of Standardization Reform in 1995, one typically requires a need statement from a vehicle program office to justify and sponsor the work. This presentation will focus on recent aluminum alloy armor plate specifications that have added capability to vehicle designers' selection of armor materials that offer possible benefits such as lower cost, higher strength, better ballistic and corrosion resistance, improved weldability, etc.

Implementation of civionics in a second generation steel-free bridge deck

NASA Astrophysics Data System (ADS)

Klowak, Chad; Rivera, Evangeline; Mufti, Aftab

2005-05-01

As the design and construction of civil structures continue to evolve, it is becoming imperative that these structures be monitored for their health. In order to meet this need, the discipline of Civionics has emerged. Civionics is a new term coined from Civil-Electronics, which is derived from the application of electronics to civil structures. It is similar to the term Avionics, which is used in the aerospace industry. If structural health monitoring is to become part of civil structural engineering, it should include Civionics. It involves the application of electronics to civil structures and aims to assist engineers in realizing the full benefits of structural health monitoring (SHM). In past SHM field applications, the main reason for the failure of a sensor was not the installation of the sensor itself but the egress of the sensor cables. Often, the cables were not handled and protected correctly. For SHM to be successful, specifications must be written on the entire process, beginning with system design and concluding with data collection, interpretation, and management. Civionics specifications include the technical requirements for a SHM system which encompasses fibre optic sensors, cables, conduits, junction boxes and the control room. A specification for data collection and storage is currently being developed as well. In the spring of 2004 research engineers at the University of Manitoba constructed a full-scale second generation steel free bridge deck. The bridge deck is the first of its kind to fully incorporate a complete civionics structural health monitoring system to monitor the deck's behaviour during destructive testing. Throughout the construction of the bridge deck, the entire installation of the civionics system was carried out by research engineers simulating an actual implementation of such a system in a large scale construction environment. One major concern that consulting engineers have raised is the impact that a civionics system that uses conduit, junction boxes, and other electrical ancillary protection, will have when embedded and installed externally on full-scale infrastructure. The full-scale destructive testing of a second generation steel-free bridge deck using a civionics system designed and implemented following guidelines in a civioncs specification manual at the University of Manitoba will provide engineers with the information necessary to address the constructability and structural integrity issues. Civioncs combined with structural health monitoring will provide engineers with feedback necessary to aid in optimizing design techniques and understanding our infrastructures performance, behaviour and state of condition.

A Systems Engineering Approach to Allocate Resources Between Protection and Sensors for Ground Systems for Offensive Operations in an Urban Environment

DTIC Science & Technology

2014-09-01

progress. In the early ages, armor started out as merely thick hides or leather that was draped over the body for protection. As human kind evolved, the...parameters. Quantity Weapons Range (m) Armour Penetration (mm RHA) Std Dev P(hit) Quantity Weapons Range (m) Armour Penetration (mm RHA) Std...183 - - Inherent Armour Thickness (mm of RHA) 1,000 1,000 500 450 AGENT IFV 3 Stryker 2 AFV Bradley BMP-2 M1A2 MBT T-90 1 2 3 AH 8 3AH-64D Class

Advanced Metals and Ceramics for Armor and Anti-Armor Applications. High-Fidelity Design and Processing of Advanced Armor Ceramics

DTIC Science & Technology

2007-06-01

microstructures through advanced powder processing , (7) nondestructive evaluation of ceramic armor, (8) investigation of the relation between quasi-static...of a green microstructure of a compact prepared by this process using Superior Graphite 490 powder that had been twice beneficiated by settling and...create a dense, uniform microstructure of highly oriented grains • Determined the relationship between processing parameters, such as shear and solids

CRASHWORTHY HELICOPTER GUNNER’S SEAT INVESTIGATION

DTIC Science & Technology

1975-01-01

less restrict- ing to gun motion than a fully armored bucket seat. The problem remains in getting the gunners to wear body armor, and this can be... motions . The adjustable seat back accommodates a gun- ner with or without body armor and troops with or without combat packs and equipment. A back flap...Developmental Retractable Monkey Harness Restraint for UH-l 1 1.9 10 Gunner Survival Vest With Body Armor (ISVESTA) Side View . . . . . . . . *. . ... .. 22

An Exploration of Integrated Ground Weapons Concepts for Armor/Anti- Armor Missions

DTIC Science & Technology

1991-01-01

de - vii signs. We examined the potential of these light armor designs closely, but did not compare them with the MBT designs. The main problem in...man MBT .............................. 93 35. Three-man remote turret des :6n: side view ............................ 95 36. Three-man remote turret...configurations, including two- and three-man ver- sions with remote and manned turrets. Section V describes some light armored vehicle de - signs, including two

Investigation of New Materials and Methods of Construction of Personnel Armor

DTIC Science & Technology

2008-12-01

NEW MATERIALS AND METHODS OF CONSTRUCTION OF PERSONNEL ARMOR by Poh, Choon Wei December 2008 Thesis Advisor: Robert S. Hixson Second...REPORT TYPE AND DATES COVERED Master’s Thesis 4. TITLE AND SUBTITLE Investigation of New Materials and Methods of Construction of Personnel Armor 6...personnel and vehicle armor. However, much of this work has focused on finding materials that were very ‘strong’ to resist penetration of objects moving

Concrete deck performance relative to air entrainment.

DOT National Transportation Integrated Search

2009-12-01

Damage to concrete due to freeze-thaw (F-T) action is a serious concern for agencies in cold regions of the United : States. The most effective method to protect concrete from F-T damage is through the addition of an air entraining : agent as an admi...

Pilot applications of electrochemical chloride extraction on concrete bridge decks in Virginia.

DOT National Transportation Integrated Search

1996-01-01

A recent SHRP study confirmed that applying an electrical field between the surface of a concrete structure and the rebars (like cathodic protection, except with 50 to 500 times more current) can expel the chloride ions from salt-contaminated reinfor...

Technical Challenges of the U.S. Army’s Ground Combat Vehicle Program

DTIC Science & Technology

2012-11-01

for mine protection and a distinctive armored extension on the top, called the doghouse. Those features optimize it for counterinsurgency operations...vehicles. Less complex approaches have also evolved, such as mines designed to attack the weaker bottoms of vehicles or improvised explosive devices...Improvised Explosive Devices, Suicide Bombers, Unexploded Ordnance, and Mines ,” section I-G-10, “Countermeasures.” See also Clay Wilson, Improvised

Battle Damage Modeling

DTIC Science & Technology

2010-05-01

has been an increasing move towards armor systems which are both structural and protection components at the same time. Analysis of material response...the materials can move. As the FE analysis progresses the component will move while the mesh remains motionless (Figure 4). Individual nodes and cells...this parameter. This subroutine needs many inputs, such as the speed of sound in the material , the FE size mesh and the safety factor, which prevents

Numerical analysis of projectile impact in woven texile structures

NASA Technical Reports Server (NTRS)

Roylance, D.

1977-01-01

Computer codes were developed for simulating the dynamic fracture and viscoelastic constitutive response due to stress wave interaction and reflections caused by ballistic impact on woven textiles. The method, which was developed for use in the design and analysis of protection devices for personnel armor, has potential for use in studies of rotor blade burst containment at high velocity. Alterations in coding required for burst containment problems are discussed.

CCP MRAP Run

NASA Image and Video Library

2018-04-20

An MRAP armored vehicle goes through a training run on the Shuttle Landing Facility to support NASA's Commercial Crew Program at the agency's Kennedy Space Center in Florida. The 45,000-pound mine-resistant ambush protected vehicle, or MRAP, was originally designed for military applications. The MRAP offers a mobile bunker for astronauts and ground crews in the unlikely event they have to get away from the launch pad quickly in an emergency.

CCP MRAP Run

NASA Image and Video Library

2018-04-20

Inside a Shuttle Landing Facility hangar at NASA's Kennedy Space Center in Florida, two MRAP armored vehicles are prepared for a training drive to support the agency's Commercial Crew Program. The 45,000-pound mine-resistant ambush protected vehicle, or MRAP, was originally designed for military applications. The MRAP offers a mobile bunker for astronauts and ground crews in the unlikely event they have to get away from the launch pad quickly in an emergency.

CCP MRAP Run

NASA Image and Video Library

2018-04-20

Inside a Shuttle Landing Facility hangar at NASA's Kennedy Space Center in Florida, an MRAP armored vehicle is prepared for a training drive to support the agency's Commercial Crew Program. The 45,000-pound mine-resistant ambush protected vehicle, or MRAP, was originally designed for military applications. The MRAP offers a mobile bunker for astronauts and ground crews in the unlikely event they have to get away from the launch pad quickly in an emergency.

CCP MRAP Run

NASA Image and Video Library

2018-04-20

Two MRAP armored vehicles go through a training run on the Shuttle Landing Facility to support NASA's Commercial Crew Program at the agency's Kennedy Space Center in Florida. The 45,000-pound mine-resistant ambush protected vehicle, or MRAPs, were originally designed for military applications. The MRAP offers a mobile bunker for astronauts and ground crews in the unlikely event they have to get away from the launch pad quickly in an emergency.

Bio-inspired Armor Protective Material Systems for Ballistic Shock Mitigation

DTIC Science & Technology

2011-01-01

Coupon testing a b s t r a c t Severe transient ballistic shocks from projectile impacts, mine blasts , or overhead artillery attacks can incapacitate an...past two decades [1]. A ballistic shock results from a significant amount of concentrated energy deposited from caliber projectile impacts, mine blasts ...LS- Dyna , has been predominately utilized to calculate the target shock responses including acceleration histo- ries, shock response spectra

Automation of Armored Four Wheel Counter Steer Vehicles

DTIC Science & Technology

2015-08-28

designed and implemented with an operator ease-of-use approach, allowing the simple transition between manual control and autonomous operation. Automation...Public Release The U.S. Army’s efforts in vehicle auto- mation are designed in part to protect soldiers in the field as they traverse poten- tially...System (AMAS) convoy autonomy, sensor, and drive-by-wire kits, to ground-up autonomous vehicle designs , such as TARDEC’s Autonomous Platform

Field Expedient Armor Modifications to US Armored Vehicles

DTIC Science & Technology

2006-06-01

Technology” (Fort Knox, KY: US Army Armor Center, 1983). 12 2Ian V. Hogg. Armour in Conflict, The Design and Tactics of Armoured Fighting...making their own whitewash. Lacking whitewash, they often resorted to commandeering white bed linen to drape over their vehicles. Both techniques proved...other Armoured Fighting Vehicles of World War II (New York: Exeter Books, 1983), 256. 19White, I. D., “Report on US vs. German Armor,” Exhibit 2, p. 6

Plans: 3'/50 Cal. Gun Platform, Boat Deck House Top & ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Plans: 3'/50 Cal. Gun Platform, Boat Deck House Top & Fidley Top, Boat Deck, Radar Platform Lower, Pilot House Top, Navigation Bridge, Upper Bridge Deck, Poop Deck, Cargo Deck, Motor Boat Platform, Bridge Deck, Forecastle Deck, Upper Deck - Taluga, Suisun Bay Reserve Fleet, Benicia, Solano County, CA

Armours for soft bodies: how far can bioinspiration take us?

PubMed

White, Zachary W; Vernerey, Franck J

2018-05-15

The development of armour is as old as the dawn of civilization. Early man looked to natural structures to harvest or replicate for protection, leaning on millennia of evolutionary developments in natural protection. Since the advent of more modern weaponry, Armor development has seemingly been driven more by materials research than bio-inspiration. However, parallels can still be drawn between modern bullet-protective armours and natural defensive structures. Soft armour for handgun and fragmentation threats can be likened to mammalian skin, and similarly, hard armour can be compared with exoskeletons and turtle shells. Via bio-inspiration, it may be possible to develop structures previously un-researched for ballistic protection. This review will cover current modern ballistic protective structures focusing on energy dissipation and absorption methods, and their natural analogues. As all armour is a compromise between weight, flexibility and protection, the imbricated structure of scaled skin will be presented as a better balance between these factors.

48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate. ...

48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate. ...

48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate. ...

48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate. ...

48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate. ...

Shell-armored wood cobbles as a potential criterion for detrital coal deposits

DOE Office of Scientific and Technical Information (OSTI.GOV)

DiMarco, M.J.; Nummedal, D.

1986-01-01

Shell-armored wood cobbles occur on detrital-peat beaches along the seaward edge of the Mississippi Delta. Shell material consists exclusively of Mulinia lateralis, a dwarf surf clam. Soft, heavy, waterlogged wood fragments are abraded and become armored by hard shells in response to wave activity on the beach. Although their preservation potential is suspect, fossilized shell-armored wood clasts would probably be recognized as a type of coal ball and might indicate an allochthonous origin for the host coal.

36 CFR 28.10 - Permitted and prohibited uses.

Code of Federal Regulations, 2011 CFR

2011-07-01

... natural resources of the Seashore, on any lands, whether publicly or privately-held, which lie below mean... a building, bulkhead, pile, septic system, revetment, deck, swimming pool, or other structure or man... education, and natural resource protection uses and facilities consistent with the uses and facilities...

46 CFR 76.25-5 - Zoning.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Automatic Sprinkling System, Details § 76.25-5 Zoning. (a) The automatic sprinkling system shall be divided into separate... more than 250 sprinkler heads. (c) The sprinkling zone may cover more than one deck, in which case, the...

46 CFR 76.25-5 - Zoning.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Automatic Sprinkling System, Details § 76.25-5 Zoning. (a) The automatic sprinkling system shall be divided into separate... more than 250 sprinkler heads. (c) The sprinkling zone may cover more than one deck, in which case, the...

46 CFR 76.25-5 - Zoning.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Automatic Sprinkling System, Details § 76.25-5 Zoning. (a) The automatic sprinkling system shall be divided into separate... more than 250 sprinkler heads. (c) The sprinkling zone may cover more than one deck, in which case, the...

46 CFR 76.25-5 - Zoning.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Automatic Sprinkling System, Details § 76.25-5 Zoning. (a) The automatic sprinkling system shall be divided into separate... more than 250 sprinkler heads. (c) The sprinkling zone may cover more than one deck, in which case, the...

46 CFR 76.25-5 - Zoning.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Automatic Sprinkling System, Details § 76.25-5 Zoning. (a) The automatic sprinkling system shall be divided into separate... more than 250 sprinkler heads. (c) The sprinkling zone may cover more than one deck, in which case, the...

RNase-Resistant Virus-Like Particles Containing Long Chimeric RNA Sequences Produced by Two-Plasmid Coexpression System▿

PubMed Central

Wei, Yuxiang; Yang, Changmei; Wei, Baojun; Huang, Jie; Wang, Lunan; Meng, Shuang; Zhang, Rui; Li, Jinming

2008-01-01

RNase-resistant, noninfectious virus-like particles containing exogenous RNA sequences (armored RNA) are good candidates as RNA controls and standards in RNA virus detection. However, the length of RNA packaged in the virus-like particles with high efficiency is usually less than 500 bases. In this study, we describe a method for producing armored L-RNA. Armored L-RNA is a complex of MS2 bacteriophage coat protein and RNA produced in Escherichia coli by the induction of a two-plasmid coexpression system in which the coat protein and maturase are expressed from one plasmid and the target RNA sequence with modified MS2 stem-loop (pac site) is transcribed from another plasmid. A 3V armored L-RNA of 2,248 bases containing six gene fragments—hepatitis C virus, severe acute respiratory syndrome coronavirus (SARS-CoV1, SARS-CoV2, and SARS-CoV3), avian influenza virus matrix gene (M300), and H5N1 avian influenza virus (HA300)—was successfully expressed by the two-plasmid coexpression system and was demonstrated to have all of the characteristics of armored RNA. We evaluated the 3V armored L-RNA as a calibrator for multiple virus assays. We used the WHO International Standard for HCV RNA (NIBSC 96/790) to calibrate the chimeric armored L-RNA, which was diluted by 10-fold serial dilutions to obtain samples containing 106 to 102 copies. In conclusion, the approach we used for armored L-RNA preparation is practical and could reduce the labor and cost of quality control in multiplex RNA virus assays. Furthermore, we can assign the chimeric armored RNA with an international unit for quantitative detection. PMID:18305135

Plans: Aft Gun Platform, Quarters for 16 Gunmen, Poop Deck, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Plans: Aft Gun Platform, Quarters for 16 Gunmen, Poop Deck, Boat Deck, House Top, Bridge Deck, Upper Bridge Deck, Navigating Bridge, Forecastle Deck, Gun Platform, Upper Deck, Second Deck and Hold Plan - Mission Santa Ynez, Suisun Bay Reserve Fleet, Benicia, Solano County, CA

Hierarchically Enhanced Impact Resistance of Bioinspired Composites.

PubMed

Gu, Grace X; Takaffoli, Mahdi; Buehler, Markus J

2017-07-01

An order of magnitude tougher than nacre, conch shells are known for being one of the toughest body armors in nature. However, the complexity of the conch shell architecture creates a barrier to emulating its cross-lamellar structure in synthetic materials. Here, a 3D biomimetic conch shell prototype is presented, which can replicate the crack arresting mechanisms embedded in the natural architecture. Through an integrated approach combining simulation, additive manufacturing, and drop tower testing, the function of hierarchy in conch shell's multiscale microarchitectures is explicated. The results show that adding the second level of cross-lamellar hierarchy can boost impact performance by 70% and 85% compared to a single-level hierarchy and the stiff constituent, respectively. The overarching mechanism responsible for the impact resistance of conch shell is the generation of pathways for crack deviation, which can be generalized to the design of future protective apparatus such as helmets and body armor. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Armored umbilical apparatus for towing a marine seismic air gun sub array

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burrage, E.C.

1985-06-25

An armored umbilical and termination housing is disclosed for towing a sub-array of seismic air guns used in marine seismic surveying comprising a single air hose for supplying all the high pressure air to the individual air guns surrounded by all the electrical control cables needed to operate the air guns in the sub-array. Protective coatings are applied around the electrical control cables and stress members for carrying the load of towing the sub-array are incorporated within the umbilical. A termination housing is provided on the end of the umbilical for terminating the single air hose and all the electricalmore » control lines to common connectors so that individual electrical control lines and air hoses can run from the termination housing to each individual air gun in the sub-array. Air shut off valves are provided so that the high pressure air can be shut off to the individual air guns within the sub-array remotely from the survey vessel.« less

Armored DNA in recombinant Baculoviruses as controls in molecular genetic assays.

PubMed

Freystetter, Andrea; Paar, Christian; Stekel, Herbert; Berg, Jörg

2017-10-01

The widespread use of molecular PCR-based assays in analytical and clinical laboratories brings about the need for test-specific, stable, and reliable external controls (EC) as well as standards and internal amplification controls (IC), in order to arrive at consistent test results. In addition, there is also a growing need to produce and provide stable, well-characterized molecular controls for quality assurance programs. In this study, we describe a novel approach to generate armored double-stranded DNA controls, which are encapsulated in baculovirus (BV) particles of the species Autographa californica multiple nucleopolyhedrovirus. We used the well-known BacPAK™ Baculovirus Expression System (Takara-Clontech), removed the polyhedrin promoter used for protein expression, and generated recombinant BV-armored DNAs. The obtained BV-armored DNAs were readily extracted by standard clinical DNA extraction methods, showed favorable linearity and performance in our clinical PCR assays, were resistant to DNase I digestion, and exhibited marked stability in human plasma and serum. BV-armored DNA ought to be used as ECs, quantification standards, and ICs in molecular assays, with the latter application allowing for the entire monitoring of clinical molecular assays for sample adequacy. BV-armored DNA may also be used to produce double-stranded DNA reference materials for, e.g., quality assurance programs. The ease to produce BV-armored DNA should make this approach feasible for a broad spectrum of molecular applications. Finally, as BV-armored DNAs are non-infectious to mammals, they may be even more conveniently shipped than clinical specimen.

30 CFR 75.700 - Grounding metallic sheaths, armors, and conduits enclosing power conductors.

Code of Federal Regulations, 2010 CFR

2010-07-01

... conduits enclosing power conductors. 75.700 Section 75.700 Mineral Resources MINE SAFETY AND HEALTH... Grounding § 75.700 Grounding metallic sheaths, armors, and conduits enclosing power conductors. [Statutory Provisions] All metallic sheaths, armors, and conduits enclosing power conductors shall be electrically...

30 CFR 75.700 - Grounding metallic sheaths, armors, and conduits enclosing power conductors.

Code of Federal Regulations, 2011 CFR

2011-07-01

... conduits enclosing power conductors. 75.700 Section 75.700 Mineral Resources MINE SAFETY AND HEALTH... Grounding § 75.700 Grounding metallic sheaths, armors, and conduits enclosing power conductors. [Statutory Provisions] All metallic sheaths, armors, and conduits enclosing power conductors shall be electrically...

31 CFR 800.302 - Transactions that are not covered transactions.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... business, produces armored personnel carriers in the United States. Corporation A, a foreign person, seeks... with the production of armored personnel carriers. Corporation A seeks to negotiate an agreement under... into a contractual arrangement to acquire the entire armored personnel carrier business operations of...

31 CFR 800.302 - Transactions that are not covered transactions.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... business, produces armored personnel carriers in the United States. Corporation A, a foreign person, seeks... with the production of armored personnel carriers. Corporation A seeks to negotiate an agreement under... into a contractual arrangement to acquire the entire armored personnel carrier business operations of...

31 CFR 800.302 - Transactions that are not covered transactions.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... business, produces armored personnel carriers in the United States. Corporation A, a foreign person, seeks... with the production of armored personnel carriers. Corporation A seeks to negotiate an agreement under... into a contractual arrangement to acquire the entire armored personnel carrier business operations of...

The Subject Headings of the Morris Swett Library, USAFAS. Revised.

DTIC Science & Technology

1980-05-15

Royal Armoured Corps. x Armored force. Armored troops. Armored units. Mechanized force. Mechanized units. Mechanized warfare. Tank companies. Tank...g., U. S. Ary- Physical training. CAMERA MOUNTS. CAMERAS, AERIAL. II I • • ! I CAMOUFLAGE. (U 166.3h) x Air arm - amouflage. - Bibliography. - Drape

Preparing soft-bodied arthropods for arthropods for microscope examination: Armored Scales (Insects: Hemiptera: Diaspididae)

USDA-ARS?s Scientific Manuscript database

Proper identification of armored scales (Hemiptera: Diaspididae) requires preparation of the specimen on a microscope slide. This training video provides visual instruction on how to prepare armored scales specimens on microscope slides for examination and identification. Steps ranging from collect...

Cost Savings Associated with the LV 100-5 Tank Engine

DTIC Science & Technology

2002-03-01

34 F. UNDER ARMOR AUXILLARY POWER UNIT...................................... 35 viii G. SUMMARY...48 E. UNDER ARMOR AUXILLARY POWER UNIT...................................... 49 F. SUMMARY...the gunner and commander thermal sights. An under armor auxiliary power unit, new computer mass memory unit, color maps and displays are included

28 CFR 33.102 - Preferences.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Judicial Administration DEPARTMENT OF JUSTICE BUREAU OF JUSTICE ASSISTANCE GRANT PROGRAMS Bulletproof Vest... armor vests based on the percentage of law enforcement officers who do not have access to an armor vest... wear armor vests whenever feasible; and (c) Has a violent crime rate at or above the national average...

28 CFR 33.102 - Preferences.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Judicial Administration DEPARTMENT OF JUSTICE BUREAU OF JUSTICE ASSISTANCE GRANT PROGRAMS Bulletproof Vest... armor vests based on the percentage of law enforcement officers who do not have access to an armor vest... wear armor vests whenever feasible; and (c) Has a violent crime rate at or above the national average...

28 CFR 33.102 - Preferences.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Judicial Administration DEPARTMENT OF JUSTICE BUREAU OF JUSTICE ASSISTANCE GRANT PROGRAMS Bulletproof Vest... armor vests based on the percentage of law enforcement officers who do not have access to an armor vest... wear armor vests whenever feasible; and (c) Has a violent crime rate at or above the national average...

28 CFR 33.102 - Preferences.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Judicial Administration DEPARTMENT OF JUSTICE BUREAU OF JUSTICE ASSISTANCE GRANT PROGRAMS Bulletproof Vest... armor vests based on the percentage of law enforcement officers who do not have access to an armor vest... wear armor vests whenever feasible; and (c) Has a violent crime rate at or above the national average...

28 CFR 33.102 - Preferences.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Judicial Administration DEPARTMENT OF JUSTICE BUREAU OF JUSTICE ASSISTANCE GRANT PROGRAMS Bulletproof Vest... armor vests based on the percentage of law enforcement officers who do not have access to an armor vest... wear armor vests whenever feasible; and (c) Has a violent crime rate at or above the national average...

New Materials and Construction for Improved Helmets

DTIC Science & Technology

1975-11-01

Kevlar fabric armor have been examined Iy .\\N1N’i and ot~wrlaboatores. he consensus has selected thle same phenol ic/polyvvinyl butyral I es inl USed...Helmet kevlar fabric laminates u,,ing phenolic /polyvinyl butyral resin withstand thermol stressing ’ad have low water absorption (2.5 percent in 24 hours...basis of laboratory te!sts for fragment protection capabilities and for durability. The mate- rials considered were (1) phenolic /polyvinyl butyral

Efficacy of Two Novel Anodic Coatings for Enhanced Corrosion Protection of Aluminum Armor Alloys

DTIC Science & Technology

2014-01-01

nitrate solution of a given metal electrolytically impregnating the porous oxide with the desired metal (5)—for example, silicon (Si) and silver (Ag...performed using the same equipment and data acquisition program previously described. Cells were filled with a 3.5% sodium chloride solution and the...electrochemical impedance spectroscopy h hour HATE Hydraulic Adhesion Test Equipment in inch NaCl sodium chloride OCP open circuit potential OSD

Biophysical Characteristics of Chemical Protective Ensemble With and Without Body Armor

DTIC Science & Technology

2015-07-01

Environmental Medicine Natick, MA 01760-5007 Standard Form 298 (Rev. 8/98) REPORT DOCUMENTATION PAGE Prescribed by ANSI Std. Z39.18 Form Approved OMB...members deployed to Iraq/Afghanistan, heat injuries totally 909, 58 of these being heat stroke [1]. While these incidences are relatively high across...As homeotherms, metabolic energy production (?̇?) in humans is a natural process, where ~20% of this energy results in useful mechanical work and

36 CFR 2.12 - Audio disturbances.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 1 2012-07-01 2012-07-01 false Audio disturbances. 2.12... RESOURCE PROTECTION, PUBLIC USE AND RECREATION § 2.12 Audio disturbances. (a) The following are prohibited..., motorized toy, or an audio device, such as a radio, television set, tape deck or musical instrument, in a...

36 CFR 2.12 - Audio disturbances.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Audio disturbances. 2.12... RESOURCE PROTECTION, PUBLIC USE AND RECREATION § 2.12 Audio disturbances. (a) The following are prohibited..., motorized toy, or an audio device, such as a radio, television set, tape deck or musical instrument, in a...

36 CFR 2.12 - Audio disturbances.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 1 2013-07-01 2013-07-01 false Audio disturbances. 2.12... RESOURCE PROTECTION, PUBLIC USE AND RECREATION § 2.12 Audio disturbances. (a) The following are prohibited..., motorized toy, or an audio device, such as a radio, television set, tape deck or musical instrument, in a...

36 CFR 2.12 - Audio disturbances.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 36 Parks, Forests, and Public Property 1 2014-07-01 2014-07-01 false Audio disturbances. 2.12... RESOURCE PROTECTION, PUBLIC USE AND RECREATION § 2.12 Audio disturbances. (a) The following are prohibited..., motorized toy, or an audio device, such as a radio, television set, tape deck or musical instrument, in a...

36 CFR 2.12 - Audio disturbances.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Audio disturbances. 2.12... RESOURCE PROTECTION, PUBLIC USE AND RECREATION § 2.12 Audio disturbances. (a) The following are prohibited..., motorized toy, or an audio device, such as a radio, television set, tape deck or musical instrument, in a...

46 CFR 72.05-35 - Hatch covers and shifting boards.

Code of Federal Regulations, 2010 CFR

2010-10-01

...-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS CONSTRUCTION AND ARRANGEMENT Structural Fire Protection § 72.05-35 Hatch covers and shifting boards. (a) Wood hatch... deck construction noted in tables 72.05-10 (f) and (g). (b) Tonnage openings in “A” Class bulkheads...

Evaluation of epoxy compounds as a material for patching and protecting concrete : final report.

DOT National Transportation Integrated Search

1971-01-01

The final report summarizes the results of a study of the use of epoxy compounds in the shallow surface repair and sealing of concrete bridge decks. The research effort concentrated on the use of epoxy resin systems as bonded overlays and included ev...

46 CFR 76.23-5 - Zoning.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-5 Zoning. (a) Separate zones may be used for each deck, and on any particular... that the end sprinkler heads of both adjoining zones will cover the identical area. Table 76.23-5(b...

46 CFR 76.23-5 - Zoning.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-5 Zoning. (a) Separate zones may be used for each deck, and on any particular... that the end sprinkler heads of both adjoining zones will cover the identical area. Table 76.23-5(b...

46 CFR 76.23-5 - Zoning.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-5 Zoning. (a) Separate zones may be used for each deck, and on any particular... that the end sprinkler heads of both adjoining zones will cover the identical area. Table 76.23-5(b...

46 CFR 76.23-5 - Zoning.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-5 Zoning. (a) Separate zones may be used for each deck, and on any particular... that the end sprinkler heads of both adjoining zones will cover the identical area. Table 76.23-5(b...

46 CFR 76.23-5 - Zoning.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-5 Zoning. (a) Separate zones may be used for each deck, and on any particular... that the end sprinkler heads of both adjoining zones will cover the identical area. Table 76.23-5(b...

46 CFR 111.70-5 - Heater circuits.

Code of Federal Regulations, 2010 CFR

2010-10-01

... REQUIREMENTS Motor Circuits, Controllers, and Protection § 111.70-5 Heater circuits. (a) If an enclosure for a motor, master switch, or other equipment has an electric heater inside the enclosure that is energized.... (b) If the location of the enclosure for a motor, master switch, or other equipment for deck...

46 CFR 98.30-37 - Firefighting requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... CONSTRUCTION, ARRANGEMENT, AND OTHER PROVISIONS FOR CERTAIN DANGEROUS CARGOES IN BULK Portable Tanks § 98.30-37... a dry chemical type are— (1) Located to protect the deck area 10 feet in any horizontal direction..., there are 2 or more dry chemical fire extinguishers of 300 pounds or more total capacity of...

14 CFR 25.1439 - Protective breathing equipment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... breathing equipment must be installed for the use of appropriate crewmembers for fighting fires in... dioxide, and other harmful gases while on flight deck duty or while combating fires. (2) The equipment... considered to be of 15-minute duration at the prescribed altitude and minute volume. If a continuous flow...

14 CFR 25.1439 - Protective breathing equipment.

Code of Federal Regulations, 2013 CFR

2013-01-01

... breathing equipment must be installed for the use of appropriate crewmembers for fighting fires in... dioxide, and other harmful gases while on flight deck duty or while combating fires. (2) The equipment... considered to be of 15-minute duration at the prescribed altitude and minute volume. If a continuous flow...

Special report. Designing security for a garage serving a new medical school: from concept to reality.

PubMed

1997-01-01

The Paterson Street Deck, New Brunswick, NJ, cited by the International Parking Institute (IPI) for excellence in design, employs a number of modern security concepts to protect its customers. The deck was built by the New Brunswick Parking Authority, which worked with the city's medical community to develop the 1,010-space structure located next to the newly built Robert Wood Johnson Medical School. The spaces are used by approximately 800 medical patrons--students of the medical school and employees of Robert Wood Johnson University Hospital, as well as an additional 200 visitors. Staffers and students pay for parking services biweekly on a graduated scale based on the level of their job title, according to Joseph Bernasz, director of administrator, Robert Wood Johnson Medical School. And they have been very receptive to the new facility, says Kevin McTernan, vice president of administrative services, Robert Wood Johnson University Hospital, New Brunswick. In this report, we'll present in detail the security concepts employed, the reasons behind them, and how they have been employed since the deck opened about two years ago.

Metallurgical Examination of 2 Inch, 2-1/2 Inch, and 3 Inch Rolled Homogeneous Armor Employed in the Ballistic Evaluation of Armor against 57 mm and 90 mm ARmor-Piercing Projectiles

DTIC Science & Technology

1949-08-24

t I- Results of Hardoed Survey* at Aberden Proving Ground an at Watertown Axue Average Average Surface Hardness...of surface hardness determination, made at Aberdeen ProvIng Ground and crocea-sectional hardness surveys made at Watertcwn Arsenal are limted in Table...Against 57 ma and, 90 w Armor-Piercing Ammunvtion,," At the request of this Arsenall,, Aerdeen Proving Ground provided 80 x 120" sections cut from a

An Annotated Bibliography of MANPRINT-Related Assessments and Evaluations Conducted by the U.S. Army, 2nd Edition: 1953 to 2009. Volume 1- Index

DTIC Science & Technology

2010-02-01

System (ACABA) MA 1973 Armored Vest M1955 Body Armor- Armored Vest M1955 USMC M1955 Armored Vest and the Proposed Titanium Nylon Improved... Laser - MILES Multiple Integrated Laser Engagement System in an Operational Environment (MILES) MA 1980 SAW M249 Rifle- 5.56mm- Machine Gun- SAW M249...Weapon System MA 1993 MCF MCF Modular Causeway Ferry (MCF) MA 1993 MDS NBC- Decon- MDS Modular Decontamination System (MDS) MA 1993 MELIOS Laser

Testing the Shuttle heat-protection armor

NASA Technical Reports Server (NTRS)

Strouhal, G.; Tillian, D. J.

1976-01-01

The article deals with the thermal protection system (TPS) designed to keep Space Shuttle structures at 350 F ratings over a wide range of temperatures encountered in orbit, but also during prelaunch, launch, deorbit and re-entry, landing and turnaround. The structure, function, fabrication, and bonding of various types of reusable surface insulation and composite materials are described. Test programs are developed for insulation, seals, and adhesion bonds; leak tests and acoustic fatigue tests are mentioned. Test facilities include arc jets, radiant heaters, furnaces, and heated tunnels. The certification tests to demonstrate TPS reusability, structural integrity, thermal performance, and endurance will include full-scale assembly tests and initial orbital flight tests.

Bilateral vagotomy inhibits apnea and attenuates other physiological responses after blunt chest trauma.

PubMed

Gryth, Dan; Rocksén, David; Arborelius, Ulf P; Drobin, Dan; Persson, Jonas K E; Sondén, Anders; Bursell, Jenny; Olsson, Lars-Gunnar; Kjellström, B Thomas

2008-06-01

Behind armor blunt trauma (BABT) is defined as the nonpenetrating injury resulting from a ballistic impact on body armor. Some of the kinetic energy is transferred to the body, causing internal injuries and, occasionally, death. The aim of this study was to investigate if apnea and other pathophysiological effects after BABT is a vagally mediated reflex. Sixteen anesthetized pigs wearing body armor, of which five were vagotomized, were shot with a standard 7.62 mm assault rifle. These animals were compared with control animals (n = 8), shot with blank ammunition. We performed bilateral vagotomy before the shot and assessed the outcome on the apnea period, respiration, circulation, and brain function. Animals were monitored during a 2-hour period after the shot. Nonvagotomized animals had a mean apnea period of 22 (6-44) seconds. This group also showed a significant decrease in oxygen saturation compared with control animals. Furthermore, electroencephalogram-changes were more pronounced in nonvagotomized animals. In contrast, vagotomized animals were protected from apnea and showed only a minor decrease in oxygen saturation. All exposed animals showed impaired circulation, and postmortem examination revealed a pulmonary contusion. This study shows that apnea after BABT is a vagally mediated reflex that can be inhibited by bilateral vagotomy. Our results indicate that the initial apnea period is an important factor for hypoxia after BABT. Supported ventilation should begin immediately if the affected person is unconscious and suffers from apnea. It should continue until the neurologic paralysis disappears and sufficient spontaneous breathing begins.

Construction of armored RNA containing long-size chimeric RNA by increasing the number and affinity of the pac site in exogenous rna and sequence coding coat protein of the MS2 bacteriophage.

PubMed

Wei, Baojun; Wei, Yuxiang; Zhang, Kuo; Yang, Changmei; Wang, Jing; Xu, Ruihuan; Zhan, Sien; Lin, Guigao; Wang, Wei; Liu, Min; Wang, Lunan; Zhang, Rui; Li, Jinming

2008-01-01

To construct a one-plasmid expression system of the armored RNA containing long chimeric RNA by increasing the number and affinity of the pac site. The plasmid pET-MS2-pac was constructed with one C-variant pac site, and then the plasmid pM-CR-2C containing 1,891-bp chimeric sequences and two C-variant pac sites was produced. Meanwhile, three plasmids (pM-CR-C, pM-CR-2W and pM-CR-W) were obtained as parallel controls with a different number and affinity of the pac site. Finally, the armored RNA was expressed and purified. The armored RNA with 1,891 bases target RNA was expressed successfully by the one-plasmid expression system with two C-variant pac sites, while for one pac site, no matter whether the affinity was changed or not, only the 1,200 bases target RNA was packaged. It was also found that the C-variant pac site could increase the expression efficiency of the armored RNA. The armored RNA with 1,891-bp exogenous RNA in our study showed the characterization of ribonuclease resistance and stability at different time points and temperature conditions. The armored RNA with 1,891 bases exogenous RNA was constructed and the expression system can be used as a platform for preparation of the armored RNA containing long RNA sequences. Copyright 2008 S. Karger AG, Basel.

The Armored Infantry in the US Force Structure.

DTIC Science & Technology

1985-12-02

armored infantry and tank integration occurred during the capture of the town of Troyes , France, in 1944, by Task Force West of the 4th Armored...Singling and Troyes . The same can not be said of the foot infantryman because normally he was not associated with tanks. Such was the case in the previously

27 CFR 478.149 - Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Armor piercing ammunition... FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.149 Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation. The...

27 CFR 478.149 - Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Armor piercing ammunition... FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.149 Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation. The...

27 CFR 478.149 - Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Armor piercing ammunition... FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.149 Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation. The...

27 CFR 478.149 - Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Armor piercing ammunition... FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.149 Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation. The...

27 CFR 478.149 - Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Armor piercing ammunition... FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Exemptions, Seizures, and Forfeitures § 478.149 Armor piercing ammunition manufactured or imported for the purpose of testing or experimentation. The...

Investigation of Advanced Personnel Armor Using Layered Construction

DTIC Science & Technology

2009-12-01

foam were constructed to test against baseline armor AISI 4140 steel plate. A hypothetical orthotropic material model closely resembling that of...against baseline armor AISI 4140 steel plate. A hypothetical orthotropic material model closely resembling that of Dyneema HB25 was derived based on...54 2. Steel AISI 4140 ...................................................................................56 3. Composite Plates

76 FR 76100 - Amendment to the International Traffic in Arms Regulations: Revision of U.S. Munitions List...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-06

..., or electromagnetic countermeasure(s) to neutralize the threat prior to contact with a vehicle) and... armor parts and components; (6) electromagnetic armor parts and components, including pulsed power parts... reactive or electromagnetic armor. Dated: 28 November 2011. Ellen O. Tauscher, Under Secretary, Arms...

A Comparison of the Scorpion Load Carriage System (SLCS) to the Modular Lightweight Load Carrying Equipment (MOLLE)

DTIC Science & Technology

2003-07-01

volunteer was asked to report wearing Battle Dress Uniform or Under Armor Undergarment) because the reflective markers used for motion capture needed to be...data collection sessions wearing Under Armor Undergarment, combat boots, integrated body armor and Scorpion helmet. Subjects were given time to

On the collapse pressure of armored bubbles and drops.

PubMed

Pitois, O; Buisson, M; Chateau, X

2015-05-01

Drops and bubbles wrapped in dense monolayers of hydrophobic particles are known to sustain a significant decrease of their internal pressure. Through dedicated experiments we investigate the collapse behavior of such armored water drops as a function of the particle-to-drop size ratio in the range 0.02-0.2. We show that this parameter controls the behavior of the armor during the deflation: at small size ratios the drop shrinkage proceeds through the soft crumpling of the monolayer, at intermediate ratios the drop becomes faceted, and for the largest studied ratios the armor behaves like a granular arch. The results show that each of the three morphological regimes is characterized by an increasing magnitude of the collapse pressure. This increase is qualitatively modeled thanks to a mechanism involving out-of-plane deformations and particle disentanglement in the armor.

Single-Enzyme Nanoparticles Armored by a Nanometer-Scale Organic/Inorganic Network

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Jungbae; Grate, Jay W.

2003-09-01

We have developed armored single-enzyme nanoparticles (SENs), which dramatically stabilize a protease (a-chymotrypsin, CT) by surrounding each enzyme molecule with a porous composite organic/inorganic shell of less than a few nanometers thick. The armored enzymes show no decrease in CT activity at 30C for four days while free CT activity is rapidly reduced by orders of magnitude. The armored shell around CT is sufficiently thin and porous that it does not place any serious mass-transfer limitation on substrates. This unique approach will have a great impact in using enzymes in various fields.

Acid mine treatment with open limestone channels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ziemkiewicz, P.F.; Brant, D.L.; Skousen, J.G.

1996-12-31

Acid mine drainage (AMD) is often associated with mining of pyritic coal and metal deposits. Typical AMD associated with coal mines in the eastern US can have acidity and iron concentrations ranging from the teens to the thousands of mg/l. Aluminum and manganese can be present in concentrations ranging from zero to the low hundreds of mg/l. Much attention has been devoted to developing inexpensive, limestone (LS)-based systems for treating AMID with little or no maintenance. However, LS tends to coat with metal hydroxides when exposed to AMID in an oxidized state, a process known as {open_quotes}armoring{close_quotes}. It is generallymore » assumed that once armored, LS ceases to neutralize acid. Another problem is that the hydroxides tend to settle into plug the pore spaces in LS beds forcing water to move around rather than through the LS. While both are caused by the precipitation of metal hydroxides, armoring and plugging are two different problems. Plugging of LS pores can be avoided by maintaining a high flushing rate through the LS bed. Armoring, however, occurs regardless of water velocity. This study investigated the influence of armoring on LS solubility and the implications of armoring and plugging on the construction of open (oxidizing) LS channels for treating AMD. We evaluated the AMID treatment performance of armored and unarmored LS in oxidizing environments both in laboratory and field studies.« less

CCP MRAP Run

NASA Image and Video Library

2018-04-20

Following a training run on the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida, MRAP back doors are opened showing seating in the armored vehicle. The 45,000-pound mine-resistant ambush protected vehicle, or MRAP, was originally designed for military applications, but will support the agency's Commercial Crew Program at the spaceport. The MRAP offers a mobile bunker for astronauts and ground crews in the unlikely event they have to get away from the launch pad quickly in an emergency.

The Armys Armored Multi Purpose Vehicle (AMPV): Background and Issues for Congress

DTIC Science & Technology

2016-02-24

vehicles and provide protection against the challenging threats that the ABCTs are designed to fight against (page 2).  Because the medical evacuation ...carriers, and medical treatment and evacuation vehicles. An estimated 3,000 of these M-113 variants are currently in service with the Army. The AMPV is...not vehicles that are specially designed and not currently in service). Some suggest that a non-developmental vehicle might make it easier for the

2008 Tactical Wheeled Vehicles Conference (TWV) Volume 3

DTIC Science & Technology

2008-02-05

Armor/ GPK OTHER SIGNIFICANT PROCUREMENT EFFORTS Project Manager COL Scott R. Kidd Deputy PM Acquisition: Tony Shaw Deputy PM Logistics: Cesare Gaglio r...Support Modularity/ Grow the Army Full spectrum support to the War Fight & Modularity LSACM1117 ASV Production Frag Kit 5/ GPK TPE Refurb Gunner Restraint...Harness HEMTT AoA LSAC Production Objective – Gunner Protection Kit (O- GPK ) HMMWV HTV FMTV M1151/52 20 3 CSL PMs ~ Approximately 220K Systems Fielded

Concepts for the development of light-weight composite structures for rotor burst containment

NASA Technical Reports Server (NTRS)

Holms, A. G.

1977-01-01

Based on published results on rotor burst containment with single materials, and on body armor using composite materials, a set of hypotheses is established as to what variables might control the design of a weight-efficient protective device. Based on modern concepts for the design and analysis of small optimum seeking experiments, a particular experiment for evaluating the hypotheses and materials was designed. The design and methods for the analysis of results are described.

46 CFR 179.360 - Watertight integrity.

Code of Federal Regulations, 2011 CFR

2011-10-01

... integrity. (a) A hatch exposed to the weather must be watertight, except that the following hatches may be weathertight: (1) A hatch on a watertight trunk that extends at least 305 millimeters (12 inches) above the weather deck; (2) A hatch in a cabin top; and (3) A hatch on a vessel that operates only on protected...

46 CFR 179.360 - Watertight integrity.

Code of Federal Regulations, 2014 CFR

2014-10-01

... integrity. (a) A hatch exposed to the weather must be watertight, except that the following hatches may be weathertight: (1) A hatch on a watertight trunk that extends at least 305 millimeters (12 inches) above the weather deck; (2) A hatch in a cabin top; and (3) A hatch on a vessel that operates only on protected...

46 CFR 179.360 - Watertight integrity.

Code of Federal Regulations, 2010 CFR

2010-10-01

... integrity. (a) A hatch exposed to the weather must be watertight, except that the following hatches may be weathertight: (1) A hatch on a watertight trunk that extends at least 305 millimeters (12 inches) above the weather deck; (2) A hatch in a cabin top; and (3) A hatch on a vessel that operates only on protected...

46 CFR 179.360 - Watertight integrity.

Code of Federal Regulations, 2012 CFR

2012-10-01

... integrity. (a) A hatch exposed to the weather must be watertight, except that the following hatches may be weathertight: (1) A hatch on a watertight trunk that extends at least 305 millimeters (12 inches) above the weather deck; (2) A hatch in a cabin top; and (3) A hatch on a vessel that operates only on protected...

46 CFR 179.360 - Watertight integrity.

Code of Federal Regulations, 2013 CFR

2013-10-01

... integrity. (a) A hatch exposed to the weather must be watertight, except that the following hatches may be weathertight: (1) A hatch on a watertight trunk that extends at least 305 millimeters (12 inches) above the weather deck; (2) A hatch in a cabin top; and (3) A hatch on a vessel that operates only on protected...

46 CFR 193.10-10 - Fire hydrants and hose.

Code of Federal Regulations, 2010 CFR

2010-10-01

... decks where no protection is afforded to the hose in heavy weather, the hose may be temporarily removed... a garden hose nozzle that is bronze or metal with strength and corrosion resistance equivalent to... and couplings shall be as follows: (1) Couplings shall be of brass, bronze, or other equivalent metal...

49 CFR 176.305 - General stowage requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., protected from sources of heat, and away from potential sources of ignition. (b) Except as otherwise... following conditions exists: (i) The bulkhead or deck is covered with at least 8 cm (3 inches) of insulation on the entire area subject to heat; (ii) A temporary wooden bulkhead at least 5 cm (2 inches) thick...

49 CFR 176.305 - General stowage requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., protected from sources of heat, and away from potential sources of ignition. (b) Except as otherwise... following conditions exists: (i) The bulkhead or deck is covered with at least 8 cm (3 inches) of insulation on the entire area subject to heat; (ii) A temporary wooden bulkhead at least 5 cm (2 inches) thick...

46 CFR 194.10-5 - Type and location.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Type and location. 194.10-5 Section 194.10-5 Shipping..., AND CONTROL OF EXPLOSIVES AND OTHER HAZARDOUS MATERIALS Magazines § 194.10-5 Type and location. (a.... (b) Magazine vans. (1) Magazine vans may be installed on deck in a location protected from boarding...

49 CFR 176.205 - Under deck stowage requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... electrical power line in the hold or compartment must be protected by a strong metal covering to prevent... (flammable gas) materials. (6) Full and efficient hatch covers must be used. Tarpaulins, if fitted, must be... from the hold or compartment. The fire screen must completely cover the open area. It must consist of...

30 CFR 816.68 - Use of explosives: Records of blasting operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (f) Type of material blasted. (g) Sketches of the blast pattern including number of holes, burden, spacing, decks, and delay pattern. (h) Diameter and depth of holes. (i) Types of explosives used. (j...-millisecond period. (l) Initiation system. (m) Type and length of stemming. (n) Mats or other protections used...

30 CFR 817.68 - Use of explosives: Records of blasting operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (f) Type of material blasted. (g) Sketches of the blast pattern including number of holes, burden, spacing, decks, and delay pattern. (h) Diameter and depth of holes. (i) Types of explosives used. (j...-millisecond period. (l) Initiation system. (m) Type and length of stemming. (n) Mats or other protections used...

30 CFR 817.68 - Use of explosives: Records of blasting operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (f) Type of material blasted. (g) Sketches of the blast pattern including number of holes, burden, spacing, decks, and delay pattern. (h) Diameter and depth of holes. (i) Types of explosives used. (j...-millisecond period. (l) Initiation system. (m) Type and length of stemming. (n) Mats or other protections used...

30 CFR 816.68 - Use of explosives: Records of blasting operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (f) Type of material blasted. (g) Sketches of the blast pattern including number of holes, burden, spacing, decks, and delay pattern. (h) Diameter and depth of holes. (i) Types of explosives used. (j...-millisecond period. (l) Initiation system. (m) Type and length of stemming. (n) Mats or other protections used...

History of the Army Ground Forces. Study Number 27. History of the Armored Force, Command and Center

DTIC Science & Technology

1946-01-01

Forces be- *• came closer. With its redesignation as the Armored Command on 2 Tuly 1945, the activ- ities of the Armored Force became more closely...techniques. Num- ber of graduates not available. .,- Clerical Courses Clerical Course - Opened 4 November 1940; closed 22 Tuly 1944. Duration of each class - 8

’Stinger under Armor:’ An Analysis of Alternatives

DTIC Science & Technology

1990-01-01

This paper examines a concept for employment of the Stinger Air Defense Artillery weapon system known as ’Stinger under Armor .’ It traces the...areas air defense in the pre-FAADS era. This broader deficiency ultimately drove the need for ’Stinger under Armor ’ as a short-term solution to a current battlefield vulnerability.

106-17 Telemetry Standards. Annex A.4. Asynchronous Recorder Multiplexer Output Re-Constructor (ARMOR)

DTIC Science & Technology

2017-07-01

Output Re-Constructor 1. General This standard defines the recommended multiplexer format for single-channel data recording on small-format (1/2 in...which is 1-based, is determined by the position of the channel’s module in the ARMOR system . The first input channel found in the ARMOR system is

8. BUILDING NO. 611. INTERIOR OF ARMOR PLATELINED TESTING CHAMBER. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. BUILDING NO. 611. INTERIOR OF ARMOR PLATE-LINED TESTING CHAMBER. 1/2' THICK ARMOR PLATING BOLTED TO WALLS, FLOOR AND CEILING. WALLS CONSTRUCTED OF 24' THICK REINFORCED CONCRETE. VENTS IN CEILING EXHAUST SMOKE FROM EXPLOSIONS. SMALLEST WHEELED VEHICLES HOLD DUDS. - Picatinny Arsenal, 600 Area, Test Areas District, State Route 15 near I-80, Dover, Morris County, NJ

Operational Leadership and Advancing Technology

DTIC Science & Technology

2009-05-04

FINAL 3. DATES COVERED (From - To) 9 Feb – 4 May 2009 4. TITLE AND SUBTITLE Operational Leadership and Advancing Technology 5a...operational leader must use his authority and leadership skills to get by in from all concerned to maximize technological advances. 15. SUBJECT TERMS...WWI armor, British armor doctrine, German Armor doctrine, operational leadership 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT

Quantifying Ballistic Armor Performance: A Minimally Invasive Approach

NASA Astrophysics Data System (ADS)

Holmes, Gale; Kim, Jaehyun; Blair, William; McDonough, Walter; Snyder, Chad

2006-03-01

Theoretical and non-dimensional analyses suggest a critical link between the performance of ballistic resistant armor and the fundamental mechanical properties of the polymeric materials that comprise them. Therefore, a test methodology that quantifies these properties without compromising an armored vest that is exposed to the industry standard V-50 ballistic performance test is needed. Currently, there is considerable speculation about the impact that competing degradation mechanisms (e.g., mechanical, humidity, ultraviolet) may have on ballistic resistant armor. We report on the use of a new test methodology that quantifies the mechanical properties of ballistic fibers and how each proposed degradation mechanism may impact a vest's ballistic performance.

Analysis of Tile-Reinforced Composite Armor. Part 1; Advanced Modeling and Strength Analyses

NASA Technical Reports Server (NTRS)

Davila, C. G.; Chen, Tzi-Kang; Baker, D. J.

1998-01-01

The results of an analytical and experimental study of the structural response and strength of tile-reinforced components of the Composite Armored Vehicle are presented. The analyses are based on specialized finite element techniques that properly account for the effects of the interaction between the armor tiles, the surrounding elastomers, and the glass-epoxy sublaminates. To validate the analytical predictions, tests were conducted with panels subjected to three-point bending loads. The sequence of progressive failure events for the laminates is described. This paper describes the results of Part 1 of a study of the response and strength of tile-reinforced composite armor.

Statistical description of flume experiments on mixed-size bed-load transport and bed armoring processes

NASA Astrophysics Data System (ADS)

Chen, D.; Zhang, Y.

2008-12-01

The objective of this paper is to describe the statistical properties of experiments on non-uniform bed-load transport as well as the mechanism of bed armoring processes. Despite substantial effort made over the last two decades, the ability to compute the bed-load flux in a turbulent system remains poor. The major obstacles include the poor understanding of the formation of armor lays on bed surfaces. Such a layer is much flow-resistible than the underlying material and therefore significantly inhibits sediment transport from the reach. To study the problem, we conducted a flume study for mixed sand/gravel sediments. We observed that aggregated sediment blocks were the most common characters in armor layers - the largest sizes resist hydraulic forces, while the smaller sizes add interlocking support and prevent loss of fine material through gaps between the larger particles. Fractional transport rates with the existing of armor layers were measured with time by sediment trapping method at the end of flume. To address the intermittent and time-varying behavior of bed-load transport during bed armoring processes, we investigated the probability distribution of the fractional bed-load transport rates, and the underlying dynamic model derived from the continuous time random walk framework. Results indicate that it is critical to consider the impact of armor layers when a flow is sufficient to move some of the finer particles and yet insufficient to move all the larger particles on a channel bed.

Effect of surface texture and structure on the development of stable fluvial armors

NASA Astrophysics Data System (ADS)

Bertin, Stephane; Friedrich, Heide

2018-04-01

Stable fluvial armors are found in river systems under conditions of partial sediment transport and limited sediment supply, a common occurrence in nature. Stable armoring is also readily recreated in experimental flumes. Initially, this bed stabilizing phenomenon was examined for different flow discharges and solely related to surface coarsening and bedload transport reduction. The models developed suggest a specific armor composition (i.e., texture) dependent on the parent bed material and formative discharge. Following developments in topographic remote sensing, recent research suggests that armor structure is an important control on bed stability and roughness. In this paper, replicated flume runs during which digital elevation models (DEMs) were collected from both exposed and flooded gravel beds are used to interpret armoring manifestations and to assess their replicability. A range of methodologies was used for the analysis, providing information on (i) surface grain size and orientation, (ii) bed-elevation distributions, (iii) the spatial coherence of the elevations at the grain-scale, (iv) surface slope and aspect, (v) grain imbrication and (vi) the spatial variability in DEM properties. The bed-surface topography was found to be more responsive than bed-material size to changes in flow strength. Our experimental results also provide convincing evidence that gravel-beds' response to water-work during parallel degradation is unique (i.e., replicable) given the formative parameters. Based on this finding, relationships between the armors' properties and formative parameters are proposed, and are supported by adding extensive data from previous research.

Persistence of 10-year old Exxon Valdez oil on Gulf of Alaska beaches: The importance of boulder-armoring

USGS Publications Warehouse

Irvine, Gail V.; Mann, Daniel H.; Short, Jeffrey W.

2006-01-01

Oil stranded as a result of the 1989 Exxon Valdez spill has persisted for >10 years at study sites on Gulf of Alaska shores distant from the spill's origin. These sites were contaminated by "oil mousse", which persists in these settings due to armoring of underlying sediments and their included oil beneath boulders. The boulder-armored beaches that we resampled in 1999 showed continued contamination by subsurface oil, despite their exposure to moderate to high wave energies. Significant declines in surface oil cover occurred at all study sites. In contrast, mousse has persisted under boulders in amounts similar to what was present in 1994 and probably in 1989. Especially striking is the general lack of weathering of this subsurface oil over the last decade. Oil at five of the six armored-beach sites 10 years after the spill is compositionally similar to 11-day old Exxon Valdez oil. Analysis of movements in the boulder-armor that covers the study beaches reveals that only minor shifts have occurred since 1994, suggesting that over the last five, and probably over the last 10 years, boulder-armors have remained largely unmoved at the study sites. These findings emphasize the importance of particular geomorphic parameters in determining stranded oil persistence. Surface armoring, combined with stranding of oil mousse, results in the unexpectedly lengthy persistence of only lightly to moderately weathered oil within otherwise high-energy wave environments.

Examination of Spray-Applied Oxsilan 9810/2 Steel Pretreatment on a Mine Resistant Ambush Protected (MRAP) Vehicle

DTIC Science & Technology

2013-10-01

2 Omitting this pretreatment/conversion coating step was justified because hexavalent chromium - based pretreatments, such as DOD-P-15328 (8...along with the fact that it does not contain chrome (hex or trivalent ), were the criteria for selecting Oxsilan 9310/2 for demonstrating on the...Hexavalent Chromium -Based DOD-P-15328D Wash Primer for MIL-A-46100D High Hard Steel Armor; ARL-TR-3393; U.S. Army Research Laboratory: Aberdeen Proving

Improving Situational Awareness in the Counter-IED Fight with the Utilization of Unmanned Sensor Systems

DTIC Science & Technology

2009-06-01

Resistant Ambush Protected (MRAP) vehicles, which were designed to withstand an antitank mine (Eisler, 2007). An EFP can penetrate a thickness of armored...These robots weigh less than 100 pounds, are man-portable, and move on small treads with seven speed settings. The TALON is controlled with a...is powered by a two-stroke piston engine and has a steerable nose and main gear, with tires suitable for rough terrain. The Tern utilizes a GPS

A Materials Approach in the Development of Multi-Threat Warfighter Head Protection

DTIC Science & Technology

2008-12-01

TUSJp TYSlp ’--- --"IO,,5083-="" H13 .’ (AI) ’AZ31B-H2’",(~",),,-- __ Figure 6. Specific Strength of Mg vs. Al Alloy Armor Plate of current interest because...perfonnance in metal alloys, and higher stiffness typically contributes to enhanced energy absorption upon ballistic impact ; therefore, one would predict...Helmets, and ballistic helmets in particular. have not been dominated by stiffness requirements but rather other properties (e.g., crash, impact

Soft Body Armor: An Overview of Materials, Manufacturing, Testing, and Ballistic Impact Dynamics

DTIC Science & Technology

2011-08-01

Atlantic Treaty Organization NIJ National Institute of Justice OTV Outer tactical vest PBI Polybenzimidazole PBO Polybenzobisoxazole PET ...grenades and mortar rounds, is performed in accordance with the North Atlantic Treaty Organization (NATO) Standardization Agreement (STANAG) 2920.6...LEVELS IN SOFT BODY ARMOR The design of woven fabrics for armor applications is complex because it requires an understanding of the related

46 CFR 181.320 - Fire hoses and nozzles.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Fire hoses and nozzles. 181.320 Section 181.320 Shipping...) FIRE PROTECTION EQUIPMENT Fire Main System § 181.320 Fire hoses and nozzles. (a) A fire hose with a nozzle must be attached to each fire hydrant at all times. For fire hydrants located on open decks or...

40 CFR 122.27 - Silvicultural activities (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2014 CFR

2014-07-01

... or after removal of bark held in self-contained bodies of water (mill ponds or log ponds) or stored on land where water is applied intentionally on the logs (wet decking). (See 40 CFR part 429, subpart... PROTECTION AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT...

40 CFR 122.27 - Silvicultural activities (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2013 CFR

2013-07-01

... or after removal of bark held in self-contained bodies of water (mill ponds or log ponds) or stored on land where water is applied intentionally on the logs (wet decking). (See 40 CFR part 429, subpart... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL...

46 CFR 194.10-20 - Magazine chest construction.

Code of Federal Regulations, 2012 CFR

2012-10-01

... lid shall have a minimum thickness of 1/8 inch. (b) Permanent sun shields shall be provided for sides... distance of 11/2 inches. Sun shields may be omitted when chests are installed “on deck protected,” shielded from direct exposure to the sun. (c) Chests shall be limited to a gross capacity of 100 cubic feet. (d...

46 CFR 194.10-20 - Magazine chest construction.

Code of Federal Regulations, 2010 CFR

2010-10-01

... lid shall have a minimum thickness of 1/8 inch. (b) Permanent sun shields shall be provided for sides... distance of 11/2 inches. Sun shields may be omitted when chests are installed “on deck protected,” shielded from direct exposure to the sun. (c) Chests shall be limited to a gross capacity of 100 cubic feet. (d...

46 CFR 194.10-20 - Magazine chest construction.

Code of Federal Regulations, 2014 CFR

2014-10-01

... lid shall have a minimum thickness of 1/8 inch. (b) Permanent sun shields shall be provided for sides... distance of 11/2 inches. Sun shields may be omitted when chests are installed “on deck protected,” shielded from direct exposure to the sun. (c) Chests shall be limited to a gross capacity of 100 cubic feet. (d...

46 CFR 194.10-20 - Magazine chest construction.

Code of Federal Regulations, 2011 CFR

2011-10-01

... lid shall have a minimum thickness of 1/8 inch. (b) Permanent sun shields shall be provided for sides... distance of 11/2 inches. Sun shields may be omitted when chests are installed “on deck protected,” shielded from direct exposure to the sun. (c) Chests shall be limited to a gross capacity of 100 cubic feet. (d...

46 CFR 194.10-20 - Magazine chest construction.

Code of Federal Regulations, 2013 CFR

2013-10-01

... lid shall have a minimum thickness of 1/8 inch. (b) Permanent sun shields shall be provided for sides... distance of 11/2 inches. Sun shields may be omitted when chests are installed “on deck protected,” shielded from direct exposure to the sun. (c) Chests shall be limited to a gross capacity of 100 cubic feet. (d...

46 CFR 171.145 - Drainage of a vessel with a cockpit.

Code of Federal Regulations, 2011 CFR

2011-10-01

... either of the following equations: A=0.1(D) square inches. A=6.94(D) square centimeters. Where— A = the combined area of the scuppers in square inches (square centimeters). D = the area of the cockpit in square feet (square meters). (e) The cockpit deck of a vessel that operates on exposed or partially protected...

46 CFR 171.145 - Drainage of a vessel with a cockpit.

Code of Federal Regulations, 2013 CFR

2013-10-01

... either of the following equations: A=0.1(D) square inches. A=6.94(D) square centimeters. Where— A = the combined area of the scuppers in square inches (square centimeters). D = the area of the cockpit in square feet (square meters). (e) The cockpit deck of a vessel that operates on exposed or partially protected...

46 CFR 171.145 - Drainage of a vessel with a cockpit.

Code of Federal Regulations, 2014 CFR

2014-10-01

... either of the following equations: A=0.1(D) square inches. A=6.94(D) square centimeters. Where— A = the combined area of the scuppers in square inches (square centimeters). D = the area of the cockpit in square feet (square meters). (e) The cockpit deck of a vessel that operates on exposed or partially protected...

46 CFR 171.145 - Drainage of a vessel with a cockpit.

Code of Federal Regulations, 2012 CFR

2012-10-01

... either of the following equations: A=0.1(D) square inches. A=6.94(D) square centimeters. Where— A = the combined area of the scuppers in square inches (square centimeters). D = the area of the cockpit in square feet (square meters). (e) The cockpit deck of a vessel that operates on exposed or partially protected...

46 CFR 171.145 - Drainage of a vessel with a cockpit.

Code of Federal Regulations, 2010 CFR

2010-10-01

... either of the following equations: A=0.1(D) square inches. A=6.94(D) square centimeters. Where— A = the combined area of the scuppers in square inches (square centimeters). D = the area of the cockpit in square feet (square meters). (e) The cockpit deck of a vessel that operates on exposed or partially protected...

Transverse-Weld Tensile Properties of a New Al-4Cu-2Si Alloy as Filler Metal

NASA Astrophysics Data System (ADS)

Sampath, K.

2009-12-01

AA2195, an Al-Cu-Li alloy in the T8P4 age-hardened condition, is a candidate aluminum armor for future combat vehicles, as this material offers higher static strength and ballistic protection than current aluminum armor alloys. However, certification of AA2195 alloy for armor applications requires initial qualification based on the ballistic performance of welded panels in the as-welded condition. Currently, combat vehicle manufacturers primarily use gas metal arc welding (GMAW) process to meet their fabrication needs. Unfortunately, a matching GMAW consumable electrode is currently not commercially available to allow effective joining of AA2195 alloy. This initial effort focused on an innovative, low-cost, low-risk approach to identify an alloy composition suitable for effective joining of AA2195 alloy, and evaluated transverse-weld tensile properties of groove butt joints produced using the identified alloy. Selected commercial off-the-shelf (COTS) aluminum alloy filler wires were twisted to form candidate twisted filler rods. Representative test weldments were produced using AA2195 alloy, candidate twisted filler rods and gas tungsten arc welding (GTAW) process. Selected GTA weldments produced using Al-4wt.%Cu-2wt.%Si alloy as filler metal consistently provided transverse-weld tensile properties in excess of 275 MPa (40 ksi) UTS and 8% El (over 25 mm gage length), thereby showing potential for acceptable ballistic performance of as-welded panels. Further developmental work is required to evaluate in detail GMAW consumable wire electrodes based on the Al-Cu-Si system containing 4.2-5.0 wt.% Cu and 1.6-2.0 wt.% Si.

Physicochemical characterization of Capstone depleted uranium aerosols IV: in vitro solubility analysis.

PubMed

Guilmette, Raymond A; Cheng, Yung Sung

2009-03-01

As part of the Capstone Depleted Uranium (DU) Aerosol Study, the solubility of selected aerosol samples was measured using an accepted in vitro dissolution test system. This static system was employed along with a SUF (synthetic ultrafiltrate) solvent, which is designed to mimic the physiological chemistry of extracellular fluid. Using sequentially obtained solvent samples, the dissolution behavior over a 46-d test period was evaluated by fitting the measurement data to two- or three-component negative exponential functions. These functions were then compared with Type M and S absorption taken from the International Commission on Radiological Protection Publication 66 Human Respiratory Tract Model. The results indicated that there was a substantial variability in solubility of the aerosols, which in part depended on the type of armor being impacted by the DU penetrator and the particle size fraction being tested. Although some trends were suggested, the variability noted leads to uncertainties in predicting the solubility of other DU-based aerosols. Nevertheless, these data provide a useful experimental basis for modeling the intake-dose relationships for inhaled DU aerosols arising from penetrator impact on armored vehicles.

Armor and anesthesia: exposure, feeling, and the soldier's body.

PubMed

MacLeish, Kenneth T

2012-03-01

For many civilians, the high-tech weapons, armor, and military medicine with which U.S. soldiers are equipped present an image of lethal capacity and physical invulnerability. But, as this article explores, soldiers themselves just as often associate the life-sustaining technology of modern warfare with feelings that range from a pragmatic ambivalence about exposure to harm all the way to profoundly unsettling vulnerability. This article, based on fieldwork among soldiers and military families at the U.S. Army's Ft. Hood, examines sensory and affective dimensions of soldiers' intimate bodily relationships with the technologies that alternately or even simultaneously keep them alive and expose them to harm. I argue that modern military discipline and technology conspire to cultivate soldiers as highly durable, capable, unfeeling, interchangeable bodies, or what might be called, after Susan Buck-Morss (1992), anesthetic subjects. But for soldiers themselves, their training, combat environment, protective gear, and weapons are a rich font of both emotional and bodily feeling that exists in complex tension with the also deeply felt military imperative to carry on in the face of extreme discomfort and danger.

Armor and Anesthesia

PubMed Central

MacLeish, Kenneth T.

2013-01-01

For many civilians, the high-tech weapons, armor, and military medicine with which U.S. soldiers are equipped present an image of lethal capacity and physical invulnerability. But, as this article explores, soldiers themselves just as often associate the life-sustaining technology of modern warfare with feelings that range from a pragmatic ambivalence about exposure to harm all the way to profoundly unsettling vulnerability. This article, based on fieldwork among soldiers and military families at the U.S. Army’s Ft. Hood, examines sensory and affective dimensions of soldiers’ intimate bodily relationships with the technologies that alternately or even simultaneously keep them alive and expose them to harm. I argue that modern military discipline and technology conspire to cultivate soldiers as highly durable, capable, unfeeling, interchangeable bodies, or what might be called, after Susan Buck-Morss (1992), anesthetic subjects. But for soldiers themselves, their training, combat environment, protective gear, and weapons are a rich font of both emotional and bodily feeling that exists in complex tension with the also deeply felt military imperative to carry on in the face of extreme discomfort and danger. PMID:22574391

Radio Hazard Safety Assessment for Marine Ship Transmitters: Measurements Using a New Data Collection Method and Comparison with ICNIRP and ARPANSA Limits

PubMed Central

Halgamuge, Malka N.

2015-01-01

We investigated the levels of radio frequency electromagnetic fields (RF EMFs) emitted from marine ship transmitters. In this study, we recorded the radio frequency (RF) electric field (EF) levels emitted from transmitters from a marine vessel focusing on the areas normally occupied by crew members and passengers. Previous studies considered radiation hazard safety assessment for marine vessels with a limited number of transmitters, such as very high-frequency (VHF) transceivers, radar and communication transmitters. In our investigation, EF levels from seven radio transmitters were measured, including: VHF, medium frequency/high frequency (MF/HF), satellite communication (Sat-Com C), AISnavigation, radar X-band and radar S-band. Measurements were carried out in a 40 m-long, three-level ship (upper deck, bridge deck and bridge roof) at 12 different locations. We developed a new data-collection protocol and performed it under 11 different scenarios to observe and measure the radiation emissions from all of the transmitters. In total, 528 EF field measurements were collected and averaged over all three levels of the marine ship with RF transmitters: the measured electric fields were the lowest on the upper deck (0.82–0.86 V/m), the highest on the bridge roof (2.15–3.70 V/m) and in between on the bridge deck (0.47–1.15 V/m). The measured EF levels were then assessed for compliance with the occupational and general public reference levels of the International Commission on Non-Ionizing Radiation Protection (ICNIRP) guidelines and the Australian Radiation Protection and Nuclear Safety Agency (ARPANSA) standards. The ICNIRP and the ARPANSA limits for the general public were exceeded on the bridge roof; nevertheless, the occupational limits were respected everywhere. The measured EF levels, hence, complied with the ICNIRP guidelines and the ARPANSA standards. In this paper, we provide a new data collection model for future surveys, which could be conducted with larger samples to verify our observations. Furthermore, this new method could be useful as a reference for researchers and industry professionals without direct access to the necessary equipment. PMID:25996887

Evaluation of weapons' combustion products in armored vehicles. Appendix A: Sampling and analysis methods. Appendix B: Analytical data. Final report, 30 September 1986-14 December 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menzies, K.T.; Randel, M.A.; Quill, A.L.

1989-01-01

The U.S. Army Biomedical Research and Development Laboratory defined an extensive research program to address the generation of potentially toxic propellant combustion products in crew compartments of armored vehicles during weapons firing. The major objectives of the research were (1) to determine the presence and concentration of propellant combustion products, (2) to determine potential crew exposure to these combustion products, and (3) to assess the efficacy of field monitoring in armored vehicles. To achieve these goals, air monitoring was conducted in selected armored vehicle types, i.e., M109, M60, M3, M1, at several Army installations.

46 CFR 69.109 - Under-deck tonnage.

Code of Federal Regulations, 2012 CFR

2012-10-01

...” means the tonnage of the space below the line of the tonnage deck, as that volume is calculated under... deck from the keel. Only decks without openings that permit space below to be exempt from inclusion in....) Spaces between the line of the tonnage deck and the higher portions of that deck are not included in...

46 CFR 69.109 - Under-deck tonnage.

Code of Federal Regulations, 2014 CFR

2014-10-01

...” means the tonnage of the space below the line of the tonnage deck, as that volume is calculated under... deck from the keel. Only decks without openings that permit space below to be exempt from inclusion in....) Spaces between the line of the tonnage deck and the higher portions of that deck are not included in...

46 CFR 69.109 - Under-deck tonnage.

Code of Federal Regulations, 2013 CFR

2013-10-01

...” means the tonnage of the space below the line of the tonnage deck, as that volume is calculated under... deck from the keel. Only decks without openings that permit space below to be exempt from inclusion in....) Spaces between the line of the tonnage deck and the higher portions of that deck are not included in...

46 CFR 69.109 - Under-deck tonnage.

Code of Federal Regulations, 2011 CFR

2011-10-01

...” means the tonnage of the space below the line of the tonnage deck, as that volume is calculated under... deck from the keel. Only decks without openings that permit space below to be exempt from inclusion in....) Spaces between the line of the tonnage deck and the higher portions of that deck are not included in...

46 CFR 178.450 - Calculation of drainage area for cockpit and well deck vessels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... PASSENGER VESSELS (UNDER 100 GROSS TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178... × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio)]; or Basic Drainage area in inch2 = (Recess Volume × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio) Recess Volume = (BR × DR) − VR BR...

46 CFR 178.450 - Calculation of drainage area for cockpit and well deck vessels.

Code of Federal Regulations, 2014 CFR

2014-10-01

... PASSENGER VESSELS (UNDER 100 GROSS TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178... × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio)]; or Basic Drainage area in inch2 = (Recess Volume × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio) Recess Volume = (BR × DR) − VR BR...

46 CFR 178.450 - Calculation of drainage area for cockpit and well deck vessels.

Code of Federal Regulations, 2011 CFR

2011-10-01

... PASSENGER VESSELS (UNDER 100 GROSS TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178... × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio)]; or Basic Drainage area in inch2 = (Recess Volume × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio) Recess Volume = (BR × DR) − VR BR...

46 CFR 178.450 - Calculation of drainage area for cockpit and well deck vessels.

Code of Federal Regulations, 2012 CFR

2012-10-01

... PASSENGER VESSELS (UNDER 100 GROSS TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178... × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio)]; or Basic Drainage area in inch2 = (Recess Volume × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio) Recess Volume = (BR × DR) − VR BR...

46 CFR 178.450 - Calculation of drainage area for cockpit and well deck vessels.

Code of Federal Regulations, 2013 CFR

2013-10-01

... PASSENGER VESSELS (UNDER 100 GROSS TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178... × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio)]; or Basic Drainage area in inch2 = (Recess Volume × Recess Ratio) + (Weather Deck Volume × Weather Deck Ratio) Recess Volume = (BR × DR) − VR BR...

46 CFR 116.1110 - Drainage of flush deck vessels.

Code of Federal Regulations, 2013 CFR

2013-10-01

... ARRANGEMENT Drainage and Watertight Integrity of Weather Decks § 116.1110 Drainage of flush deck vessels. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel must be...

46 CFR 178.430 - Drainage of well deck vessels.

Code of Federal Regulations, 2012 CFR

2012-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.430 Drainage of well deck vessels. (a) The weather deck on a well deck vessel must be watertight. (b) The area required on a well...

46 CFR 116.1110 - Drainage of flush deck vessels.

Code of Federal Regulations, 2012 CFR

2012-10-01

... ARRANGEMENT Drainage and Watertight Integrity of Weather Decks § 116.1110 Drainage of flush deck vessels. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel must be...

46 CFR 178.430 - Drainage of well deck vessels.

Code of Federal Regulations, 2014 CFR

2014-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.430 Drainage of well deck vessels. (a) The weather deck on a well deck vessel must be watertight. (b) The area required on a well...

46 CFR 178.410 - Drainage of flush deck vessels.

Code of Federal Regulations, 2011 CFR

2011-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.410 Drainage of flush deck vessels. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel...

46 CFR 178.430 - Drainage of well deck vessels.

Code of Federal Regulations, 2013 CFR

2013-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.430 Drainage of well deck vessels. (a) The weather deck on a well deck vessel must be watertight. (b) The area required on a well...

46 CFR 178.430 - Drainage of well deck vessels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.430 Drainage of well deck vessels. (a) The weather deck on a well deck vessel must be watertight. (b) The area required on a well...

46 CFR 178.410 - Drainage of flush deck vessels.

Code of Federal Regulations, 2012 CFR

2012-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.410 Drainage of flush deck vessels. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel...

46 CFR 116.1110 - Drainage of flush deck vessels.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ARRANGEMENT Drainage and Watertight Integrity of Weather Decks § 116.1110 Drainage of flush deck vessels. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel must be...

46 CFR 178.410 - Drainage of flush deck vessels.

Code of Federal Regulations, 2013 CFR

2013-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.410 Drainage of flush deck vessels. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel...

46 CFR 178.410 - Drainage of flush deck vessels.

Code of Federal Regulations, 2014 CFR

2014-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.410 Drainage of flush deck vessels. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel...

46 CFR 116.1110 - Drainage of flush deck vessels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ARRANGEMENT Drainage and Watertight Integrity of Weather Decks § 116.1110 Drainage of flush deck vessels. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel must be...

46 CFR 178.430 - Drainage of well deck vessels.

Code of Federal Regulations, 2011 CFR

2011-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.430 Drainage of well deck vessels. (a) The weather deck on a well deck vessel must be watertight. (b) The area required on a well...

46 CFR 178.410 - Drainage of flush deck vessels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... TONS) INTACT STABILITY AND SEAWORTHINESS Drainage of Weather Decks § 178.410 Drainage of flush deck vessels. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel...

Anesthetic management of a case of armored brain.

PubMed

Gupta, Surender Kumar; Pandia, Mihir Prakash

2015-01-01

Armored brain is condition, which occurs due to calcification in a chronic subdural hematoma (SDH). Here, we are reporting a case of armored brain due to chronic SDH as a complication of vetriculoperitoneal shunt (VP shunt). Patient had undergone major surgery for removal of calcified hematoma. VP shunt is a simple surgery, but can lead to catastrophic complications like this. In this report, we had described this condition and its aspects.

A New Paradigm for NDE (Non Destructive Evaluation)

DTIC Science & Technology

2013-12-06

determining specific physical properties of the armor which are correlated with armor structural health. A pair of Lead Zirconate Titanate ( PZT ...this is commonly called the “pitch and catch” method. The armor plate vibrates when it is excited by a mechanical vibration from the PZT actuator...transducer, and this vibration is transmitted through the plate and induces an electrical signal in the PZT receiver transducer by virtue of the

Cross-Validation of Predictor Equations for Armor Crewman Performance

DTIC Science & Technology

1980-01-01

Technical Report 447 CROSS-VALIDATION OF PREDICTOR EQUATIONS FOR ARMOR CREWMAN PERFORMANCE Anthony J. Maitland , Newell K. Eaton, and Janet F. Neft...ORG. REPORT NUMBER Anthony J/ Maitland . Newell K/EatorV. and B OTATO RN UBR. 9- PERFORMING ORGANIZATION NAME AND ADDRESS I0. PROGRAM ELEMENT, PROJECT...Technical Report 447 CROSS-VALIDATION OF PREDICTOR EQUATIONS FOR ARMOR CREWMAN PERFORMANCE Anthony J. Maitland , Newell K. Eaton, Accession For and

The addition of body armor diminishes dynamic postural stability in military soldiers.

PubMed

Sell, Timothy C; Pederson, Jonathan J; Abt, John P; Nagai, Takashi; Deluzio, Jennifer; Wirt, Michael D; McCord, Larry J; Lephart, Scott M

2013-01-01

Poor postural stability has been identified as a risk factor for lower extremity musculoskeletal injury. The additional weight of body armor carried by Soldiers alters static postural stability and may predispose Soldiers to lower extremity musculoskeletal injuries. However, static postural stability tasks poorly replicate the dynamic military environment, which places considerable stress on the postural control system during tactical training and combat. Therefore, the purpose of this study was to examine the effects of body armor on dynamic postural stability during single-leg jump landings. Thirty-six 101st Airborne Division (Air Assault) Soldiers performed single-leg jump landings in the anterior direction with and without wearing body armor. The dynamic postural stability index and the individual stability indices (medial-lateral stability index, anterior-posterior stability index, and vertical stability index) were calculated for each condition. Paired sample t-tests were performed to determine differences between conditions. Significant differences existed for the medial-lateral stability index, anterior-posterior stability index, vertical stability index, and dynamic postural stability index (p < 0.05). The addition of body armor resulted in diminished dynamic postural stability, which may result in increased lower extremity injuries. Training programs should address the altered dynamic postural stability while wearing body armor in attempts to promote adaptations that will result in safer performance during dynamic tasks.

Construction of crack-free bridge decks : technical summary.

DOT National Transportation Integrated Search

2017-04-01

The report documents the performance of the decks based on crack surveys performed on the LC-HPC decks and : matching control bridge decks. The specifications for LC-HPC bridge decks, which cover aggregates, concrete, : and construction procedures, a...

46 CFR 171.140 - Drainage of a flush deck vessel.

Code of Federal Regulations, 2014 CFR

2014-10-01

... PERTAINING TO VESSELS CARRYING PASSENGERS Drainage of Weather Decks § 171.140 Drainage of a flush deck vessel. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel must...

46 CFR 171.140 - Drainage of a flush deck vessel.

Code of Federal Regulations, 2010 CFR

2010-10-01

... PERTAINING TO VESSELS CARRYING PASSENGERS Drainage of Weather Decks § 171.140 Drainage of a flush deck vessel. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel must...

46 CFR 171.140 - Drainage of a flush deck vessel.

Code of Federal Regulations, 2013 CFR

2013-10-01

... PERTAINING TO VESSELS CARRYING PASSENGERS Drainage of Weather Decks § 171.140 Drainage of a flush deck vessel. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel must...

46 CFR 171.140 - Drainage of a flush deck vessel.

Code of Federal Regulations, 2012 CFR

2012-10-01

... PERTAINING TO VESSELS CARRYING PASSENGERS Drainage of Weather Decks § 171.140 Drainage of a flush deck vessel. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel must...

46 CFR 171.140 - Drainage of a flush deck vessel.

Code of Federal Regulations, 2011 CFR

2011-10-01

... PERTAINING TO VESSELS CARRYING PASSENGERS Drainage of Weather Decks § 171.140 Drainage of a flush deck vessel. (a) Except as provided in paragraph (b) of this section, the weather deck on a flush deck vessel must...

DORMAN computer program (study 2.5). Volume 3: Original data bank listing. [development of data bank for computerized information storage of NASA programs

NASA Technical Reports Server (NTRS)

Stricker, L. T.

1973-01-01

A number of analyses have been performed using the DORCA program for several NASA-funded Aerospace Corporation studies in the past few years. The data decks containing the input data for these analyses have been compiled and are submitted, under separate cover. A few of the data decks are full (basic) decks containing every data item and are used as reference decks in the data bank. The other data decks were obtained by differencing a full deck with respect to one of the reference decks. Using the DORMAN program, a full deck can be recreated from the modified deck and its reference deck when and if desired. The content and structure of the data bank are described. A description of each of these data decks is presented. Three of the cases that are included in this volume have become so widely recognized and accepted that additional descriptive material has been provided. The three cases are: Case 500 Costs, Case 506 Costs, and Case 403.

Special Report on Lessons Learned (1985-2011). Volume 2: Handbook of Recommended Design Practices (Fire Protection and Life Safety Design Guidelines for Special Purpose Underground Structures)

DTIC Science & Technology

2012-10-01

mounted pads (also called a raft, bed, platform or floating deck depending on the A & E company’s terminology preference). Combinations of each of...these are frequently employed which is most common where a shock mounted pad is installed. Shock mounting each piece of equipment is self...when a UGF uses shock mounted pads for its major equipment spaces, but does not put all fire protection equipment on the pad . A shock mounted pad

International Space Agency CIO Forum Industrial Control System (ICS) and Cyber

NASA Technical Reports Server (NTRS)

Powell, Robert

2017-01-01

This briefing covers Industrial Control System (ICS) best practices for enhancing cyber protection. The briefing provides a very high-level overview of best practices currently being pursued by NASA as well as by other US government agencies such as NIST and DHS ICS-CERT. All information presented in this slide deck is publicly available and no sensitive information is provided in these slides. These slides will be used to generate discussion around best practices within the international community in the area of ICS cyber protections.

Comparison of Biophysical Characteristics and Predicted Thermophysiological Responses of Three Prototype Body Armor Systems Versus Baseline U.S. Army Body Armor Systems

DTIC Science & Technology

2015-06-19

effective and scientifically valid method of making comparisons of clothing and equipment changes prior to conducting human research. predictive modeling...valid method of making comparisons of clothing and equipment changes prior to conducting human research. 2 INTRODUCTION Modern day...clothing and equipment changes prior to conducting human research. METHODS Ensembles Three different body armor (BA) plus clothing ensembles were

Simulated Tank Anti-Armor Gunnery System (STAGS-TOW).

DTIC Science & Technology

1983-05-01

to train TOW gunners. It is derived from a model previously developed for DRAGON. The system employs a terrain board with model enemy armored vehicles ...gunnery training. TOW is a crew-portable, heavy anti-tank weapon designed to attack and defeat armored vehicles and field fortifications. The missile is...a target area, converts the infrared energy to electrical signals and then to visible light and displays the visible light as a real-time scene for

Visualization and Analysis of Impact Damage in Sapphire

DTIC Science & Technology

2011-11-01

transparent armor materials like Starphire soda - lime and borosilicate glass [8], fused silica [9] and the transparent polycrystalline ceramic AlON...conventional glass -based armor when a transparent ceramic is used as strike face on a glass -polymer laminate [1, 2, 3]. Sapphire, i.e. single crystal aluminum...materials. Since part of transparent armor consists of brittle materials, the fragmentation of the ceramic and glass layers plays a key role in the

Anesthetic management of a case of armored brain

PubMed Central

Gupta, Surender Kumar; Pandia, Mihir Prakash

2015-01-01

Armored brain is condition, which occurs due to calcification in a chronic subdural hematoma (SDH). Here, we are reporting a case of armored brain due to chronic SDH as a complication of vetriculoperitoneal shunt (VP shunt). Patient had undergone major surgery for removal of calcified hematoma. VP shunt is a simple surgery, but can lead to catastrophic complications like this. In this report, we had described this condition and its aspects. PMID:25558206

Fabrication of High Strength Lightweight Metals for Armor and Structural Applications: Large Scale Equal Channel Angular Extrusion Processing of Aluminum 5083 Alloy

DTIC Science & Technology

2017-06-01

ARL-TR-8047 ● JUNE 2017 US Army Research Laboratory Fabrication of High -Strength Lightweight Metals for Armor and Structural...to the originator. ARL-TR-8047 ● JUNE 2017 US Army Research Laboratory Fabrication of High -Strength Lightweight Metals for...Fabrication of High -Strength Lightweight Metals for Armor and Structural Applications: Large-Scale Equal Channel Angular Extrusion Processing of

Friction Stir Weld Failure Mechanisms in Aluminum-Armor Structures Under Ballistic Impact Loading Conditions

DTIC Science & Technology

2013-01-01

REPORT Friction Stir Weld Failure Mechanisms in Aluminum -Armor Structures Under Ballistic Impact Loading Conditions 14. ABSTRACT 16. SECURITY...Stir Weld Failure Mechanisms in Aluminum -Armor Structures Under Ballistic Impact Loading Conditions M. Grujicic, B. Pandurangan, A. Arakere, C-F. Yen...K.O. Pedersen, Fracture Mechanisms of Aluminum Alloy AA7075-T651 Under Various Loading Conditions , Int. J. Impact Eng., 2010, 37, p 537–551 24. T

Ground Vehicle System Integration (GVSI) and Design Optimization Model.

DTIC Science & Technology

1996-07-30

number of stowed kills Same basic load lasts longer range Gun/ammo parameters impact system weight, under - armor volume requirements Round volume...internal volume is reduced, the model assumes that the crew’s ability to operate while under armor will be impaired. If the size of a vehicle crew is...changing swept volume will alter under armor volume requirements for the total system; if system volume is fixed, changing swept volume will

Weapon System Implications of RLPG Technology

DTIC Science & Technology

2000-01-01

the extreme emphasis placed on minimizing volume under armor . For an RLPG, the space required is further reduced because, unlike the case with an SPG...ensuring that all the on-board missiles can be launched from under armor . Currently, vehicle-launched missiles are fired from racks of four launch...reload is not done under armor . External, manual reload for the direct-fire role is simply not feasible operationally. It is possible to design a

TRADOC Annual Command History, 1 January to 31 December 1991

DTIC Science & Technology

1992-06-01

24th Infantry Division (Mechanized), the French 6th Light Armored Division, the 3d Armored Cavalry Regiment, and other units assigned; and VII Corps...under Lt. Gen. Frederick M. Franks, Jr., with the U.S. Ist Infantry Division (Mechanized), Ist and 3d Armored Divisions, the Ist Cavalry Division, the...Alma Ata, Kazakhstan, the presidents of all the former republics except Georgia and the three seceding Baltic states, declared formation of the

The Armys Armored Multi Purpose Vehicle (AMPV): Background and Issues for Congress

DTIC Science & Technology

2017-01-11

M-113 personnel carriers, which are still in service in a variety of support capacities in Armored Brigade Combat Teams (ABCTs). While M-113s no...reliability, and interoperability by mission role variant within the Heavy Brigade Combat Team (HBCT) [now known as the Armored Brigade Combat Team – ABCT... teams within complex operational environments. For example, “commanders will not allow them to leave Forward Operating Bases (FOBs) or enter

Thermal modeling of W rod armor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nygren, Richard Einar

2004-09-01

Sandia has developed and tested mockups armored with W rods over the last decade and pioneered the initial development of W rod armor for International Thermonuclear Experimental Reactor (ITER) in the 1990's. We have also developed 2D and 3D thermal and stress models of W rod-armored plasma facing components (PFCs) and test mockups and are applying the models to both short pulses, i.e. edge localized modes (ELMs), and thermal performance in steady state for applications in C-MOD, DiMES testing and ITER. This paper briefly describes the 2D and 3D models and their applications with emphasis on modeling for an ongoingmore » test program that simulates repeated heat loads from ITER ELMs.« less

Plate & tube bridge deck evaluation in the deck test bed of the Troutville, Virginia, weigh station.

DOT National Transportation Integrated Search

2004-01-01

This report addresses the laboratory and field performance of multi-cellular fiber-reinforced polymer (FRP) composite bridge deck systems. We focus specifically on FRP decks produced from adhesively bonded pultrusions where the core of the deck posse...

76 FR 63229 - Airworthiness Directives; The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-12

... automatic shutoff system for the center and auxiliary tank fuel boost pumps, as applicable, and installing a placard in the airplane flight deck if necessary; replacing the P5-2 fuel system module assembly; and installing the un-commanded on (UCO) protection system for the center and auxiliary tank fuel boost pumps, as...

46 CFR 34.20-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 1 2011-10-01 2011-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Deck Foam System, Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed...

A PROBABILISTIC EXPOSURE ASSESSMENT FOR CHILDREN WHO CONTACT CCA-TREATED PLAYSETS AND DECKS USING THE STOCHASTIC HUMAN EXPOSURE AND DOSE SIMULATION (SHEDS) MODEL FOR THE WOOD PRESERVATIVE EXPOSURE SCENARIO

EPA Science Inventory

The U.S. Environmental Protection Agency has conducted a probabilistic exposure and dose assessment on the arsenic (As) and chromium (Cr) components of Chromated Copper Arsenate (CCA) using the Stochastic Human Exposure and Dose Simulation model for wood preservatives (SHEDS-Wood...

Influence of forest and rangeland management on anadromous fish habitat in Western North America: planning forest roads to protect salmonid habitat.

Treesearch

Carlton S. Yee; Terry D. Roelofs

1980-01-01

The construction and existence of forest roads, landings, and decking areas may have significant effects on anadromous fish habitat . Major effects discussed in this paper are increased sedimentation from transportation networks, the hindrance to fish migration of drainage structures, and possible changes in water quality from road stabilization additives. Guidelines...

46 CFR 171.010 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... weather deck extending no more than one-half of the vessel's length over deck (LOD) measured over the weather deck. (b) Deepest subdivision load line means the waterline that corresponds to the deepest draft... tangent to the waterline. (g) Flush deck means a continuous weather deck located at the uppermost sheer...

46 CFR 171.010 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... weather deck extending no more than one-half of the vessel's length over deck (LOD) measured over the weather deck. (b) Deepest subdivision load line means the waterline that corresponds to the deepest draft... tangent to the waterline. (g) Flush deck means a continuous weather deck located at the uppermost sheer...

Strategic sensor locations of FPR bridge decks

NASA Astrophysics Data System (ADS)

Wu, Hwai-Chung; Warnemuende, Kraig; Yan, An; Mu, Bin

2003-07-01

Advanced fiber-reinforced polymer composite (FRP) has been increasingly used in bridge deck to replace concrete or steel. A FRP bridge deck can be designed to meet AASHTO HS-25 load requirements. FRP decks have many advantages over the conventional reinforced concrete or steel decks owing to their lightweight, high strength and corrosion resistance. However, such new deck system requires extensive monitoring to ensure its designed performance before its widespread acceptance by the bridge community. For inspection and evaluation purpose, a proper monitoring system consisting of various kinds of sensors installed in the FRP deck is critical. This paper provides a framework for designing an efficient monitoring system. The strategic sensor locations are identified based on the stress analysis of the FRP deck.

PV module mounting method and mounting assembly

DOEpatents

Lenox, Carl J.S.; Johnson, Kurt M.

2013-04-23

A method for mounting PV modules to a deck includes selecting PV module layout pattern so that adjacent PV module edges are spaced apart. PV mounting and support assemblies are secured to the deck according to the layout pattern using fasteners extending into the deck. The PV modules are placed on the PV mounting and support assemblies. Retaining elements are located over and secured against the upper peripheral edge surfaces of the PV modules so to secure them to the deck with the peripheral edges of the PV modules spaced apart from the deck. In some examples a PV module mounting assembly, for use on a shingled deck, comprises flashing, a base mountable on the flashing, a deck-penetrating fastener engageable with the base and securable to the deck so to secure the flashing and the base to the shingled deck, and PV module mounting hardware securable to the base.

Characterization of limestone reacted with acid-mine drainage in a pulsed limestone bed treatment system at the Friendship Hill National Historical Site, Pennsylvania, USA

USGS Publications Warehouse

Hammarstrom, J.M.; Sibrell, P.L.; Belkin, H.E.

2003-01-01

Armoring of limestone is a common cause of failure in limestone-based acid-mine drainage (AMD) treatment systems. Limestone is the least expensive material available for acid neutralization, but is not typically recommended for highly acidic, Fe-rich waters due to armoring with Fe(III) oxyhydroxide coatings. A new AMD treatment technology that uses CO2 in a pulsed limestone bed reactor minimizes armor formation and enhances limestone reaction with AMD. Limestone was characterized before and after treatment with constant flow and with the new pulsed limestone bed process using AMD from an inactive coal mine in Pennsylvania (pH = 2.9, Fe = 150 mg/l, acidity = 1000 mg/l CaCO3). In constant flow experiments, limestone is completely armored with reddish-colored ochre within 48 h of contact in a fluidized bed reactor. Effluent pH initially increased from the inflow pH of 2.9 to over 7, but then decreased to 6 during operation. Limestone removed from a pulsed bed pilot plant is a mixture of unarmored, rounded and etched limestone grains and partially armored limestone and refractory mineral grains (dolomite, pyrite). The ???30% of the residual grains in the pulsed flow reactor that are armored have thicker (50- to 100-??m), more aluminous coatings and lack the gypsum rind that develops in the constant flow experiment. Aluminium-rich zones developed in the interior parts of armor rims in both the constant flow and pulsed limestone bed experiments in response to pH changes at the solid/solution interface. ?? 2003 Elsevier Ltd. All rights reserved.

Manufacturing process scale-up of optical grade transparent spinel ceramic at ArmorLine Corporation

NASA Astrophysics Data System (ADS)

Spilman, Joseph; Voyles, John; Nick, Joseph; Shaffer, Lawrence

2013-06-01

While transparent Spinel ceramic's mechanical and optical characteristics are ideal for many Ultraviolet (UV), visible, Short-Wave Infrared (SWIR), Mid-Wave Infrared (MWIR), and multispectral sensor window applications, commercial adoption of the material has been hampered because the material has historically been available in relatively small sizes (one square foot per window or less), low volumes, unreliable supply, and with unreliable quality. Recent efforts, most notably by Technology Assessment and Transfer (TA and T), have scaled-up manufacturing processes and demonstrated the capability to produce larger windows on the order of two square feet, but with limited output not suitable for production type programs. ArmorLine Corporation licensed the hot-pressed Spinel manufacturing know-how of TA and T in 2009 with the goal of building the world's first dedicated full-scale Spinel production facility, enabling the supply of a reliable and sufficient volume of large Transparent Armor and Optical Grade Spinel plates. With over $20 million of private investment by J.F. Lehman and Company, ArmorLine has installed and commissioned the largest vacuum hot press in the world, the largest high-temperature/high-pressure hot isostatic press in the world, and supporting manufacturing processes within 75,000 square feet of manufacturing space. ArmorLine's equipment is capable of producing window blanks as large as 50" x 30" and the facility is capable of producing substantial volumes of material with its Lean configuration and 24/7 operation. Initial production capability was achieved in 2012. ArmorLine will discuss the challenges that were encountered during scale-up of the manufacturing processes, ArmorLine Optical Grade Spinel optical performance, and provide an overview of the facility and its capabilities.

Micro-engineered first wall tungsten armor for high average power laser fusion energy systems

NASA Astrophysics Data System (ADS)

Sharafat, Shahram; Ghoniem, Nasr M.; Anderson, Michael; Williams, Brian; Blanchard, Jake; Snead, Lance; HAPL Team

2005-12-01

The high average power laser program is developing an inertial fusion energy demonstration power reactor with a solid first wall chamber. The first wall (FW) will be subject to high energy density radiation and high doses of high energy helium implantation. Tungsten has been identified as the candidate material for a FW armor. The fundamental concern is long term thermo-mechanical survivability of the armor against the effects of high temperature pulsed operation and exfoliation due to the retention of implanted helium. Even if a solid tungsten armor coating would survive the high temperature cyclic operation with minimal failure, the high helium implantation and retention would result in unacceptable material loss rates. Micro-engineered materials, such as castellated structures, plasma sprayed nano-porous coatings and refractory foams are suggested as a first wall armor material to address these fundamental concerns. A micro-engineered FW armor would have to be designed with specific geometric features that tolerate high cyclic heating loads and recycle most of the implanted helium without any significant failure. Micro-engineered materials are briefly reviewed. In particular, plasma-sprayed nano-porous tungsten and tungsten foams are assessed for their potential to accommodate inertial fusion specific loads. Tests show that nano-porous plasma spray coatings can be manufactured with high permeability to helium gas, while retaining relatively high thermal conductivities. Tungsten foams where shown to be able to overcome thermo-mechanical loads by cell rotation and deformation. Helium implantation tests have shown, that pulsed implantation and heating releases significant levels of implanted helium. Helium implantation and release from tungsten was modeled using an expanded kinetic rate theory, to include the effects of pulsed implantations and thermal cycles. Although, significant challenges remain micro-engineered materials are shown to constitute potential candidate FW armor materials.