Rock-magnetic analyses as a tool to investigate archaeological fired sediments: a case study of Mirador cave (Sierra de Atapuerca, Spain)

NASA Astrophysics Data System (ADS)

Carrancho, Á.; Villalaín, J. J.; Angelucci, D. E.; Dekkers, M. J.; Vallverdú, J.; Vergès, J. M.

2009-10-01

Here we report a detailed mineral magnetic study of Neolithic burnt levels in the Mirador Cave (Sierra de Atapuerca, Burgos, Spain) to reconstruct the burning history and to investigate their suitability for archaeomagnetic purposes. As a consequence of the ancient burning, a characteristic facies sequence was developed along the Holocene stratigraphy. From top to bottom it includes: (i) 2-10 cm ash layers, (ii) ~2 cm underlying rubefied layers and (iii) clay, mainly unburnt and of variable thickness. In some cases a thermally altered facies (2-6 cm) with a heterogeneous texture was identified (facies TF), usually between rubefactions and the unburnt levels. 126 oriented samples from 4 units (MIR12, 15, 18 and 21) and a 2 m section, all comprised between units MIR21 (6380 +/- 40 14C BP) and MIR9 (5090 +/- 40 14C BP) were analysed with rock magnetic methods. In addition, bulk sediment from each facies that comprise the Neolithic sequence was investigated. Measurements included: stepwise alternating field and thermal demagnetization of natural remanent magnetization (NRM), viscosity experiments, determination of the anisotropy of the magnetic susceptibility (AMS), the susceptibility frequency dependence at room temperature and determination of the temperature dependence of the susceptibility. Additional experiments consisted in the determination of the behaviour of anhysteretic and isothermal (IRM) remanences, magnetic hysteresis loops, first-order-reversal-curve diagrams, and thermal demagnetization of three-axial IRM. It appeared that the facies all show a fairly similar magnetic mineralogy and grain size dominated by low-titanium magnetite that is often partially maghaemitized. Main differences constitute the amount of superparamagnetic particles that is higher in unburnt strata concurring with a less well-defined NRM behaviour. The magnetic mineral concentration is notably higher in ashes. This homogeneity strongly suggests that similar sources and burial conditions prevailed during Neolithic times. Agreeing with archaeological observations and favoured by rapid burial conditions, very limited alterations have been deduced. AMS data revealed the absence of fluid flow in the ash lenses sampled. Demagnetization revealed a stable single NRM component in ashes, a single or two-component NRM in rubefactions and less stable multicomponent behaviour in clays. In ashes, magnetic minerals are likely secondary in origin formed by low-temperature oxidization soon after burning. Although this thermochemical nature of the NRM invalidates the use of these sediments for palaeointensity studies, archaeomagnetic (directional) data can be successfully obtained because the burning and oxidation are closely confined in time.

Leaching characteristics of arsenic and selenium from coal fly ash: role of calcium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian Wang; Jianmin Wang; Yulin Tang

2009-05-15

Understanding the leaching behavior of arsenic (As) and selenium (Se) in coal fly ash is important in evaluating the potential environmental impact of coal fly ash. Batch experiments were employed to systematically investigate the leaching behavior of As and Se in two major types of coal fly ashes, bituminous coal ash and sub-bituminous coal ash, and to determine the underlying processes that control As and Se leaching. The effects of pH, solid/liquid (S/L) ratio, calcium addition, and leaching time on the release of As and Se were studied. Overall, bituminous coal ash leached significantly more As and Se than sub-bituminousmore » coal ash, and Se was more readily leachable, in both absolute concentration and relative fraction, than As for both types of fly ashes. Adsorption/desorption played a major role on As and Se leaching from bituminous coal ashes. However, calcium precipitation played the most important role in reducing As and Se leaching from sub-bituminous coal ashes in the entire experimental pH range. The leaching of As and Se from bituminous coal ashes generally increased with increases in the S/L ratio and leaching time. However, for sub-bituminous coal ashes, the leaching of As was not detected under most experimental conditions, while the leaching of Se increased with increases in the S/L ratio and leaching time. As{sup V} and Se{sup IV} were found to be the major species in all ash leachates in this study. 46 refs., 7 figs., 1 tab.« less

Ash, the emerald ash borer, and private forest land management

Treesearch

Tom Crowe

2010-01-01

Forest management through emerald ash borer (EAB) will be a dynamic process that will change based on the best information available at the time. Management decisions will depend on the anticipated time of EAB arrival; the diameter and number of ash present in the forest stand; the diameter and number of other desirable and undesirable species present in the stand (...

Thermal Stability of Volcanic Ash versus Turbine Ingestion Test Sands: an Experimental Investigation

NASA Astrophysics Data System (ADS)

Cimarelli, C.; Kueppers, U.; Hess, K.; Dingwell, D. B.; Rickerby, D. S.; Madden, P. C.

2010-12-01

Volcanic eruptions are an inevitable natural threat. The range of eruptive styles is large and short term fluctuations of explosivity or vent position pose a large risk not necessarily confined to the immediate vicinity of a volcano. Explosive eruptions rather may also affect aviation, infrastructure and climate, regionally as well as globally. The recent eruption of Eyjafjallajökull drastically brought into common awareness how volcanic activity can affect every day’s life and disrupt air traffic. The presence of solid particles in the air ingested in jet turbines may cause harm as it 1) may deposit on surfaces upon being heated up and 2) abrade upon impact. Particles suspended in the atmosphere may have different origins, including volcanic ash, aeolian sand, or incineration residues, each of them having different chemical and physical characteristics. To date, aircraft turbine operability has been investigated - amongst other tests - through the ingestion of sands whose grains have different mineralogical nature. Due to high cooling rates, volcanic ash is usually made up of glass, i.e. an amorphous phase lacking crystallographic order. Glass and crystal behave very differently to heating up. Glass will soften - and accordingly change shape or stick to surfaces - at temperatures as low as 700 °C, depending on the chemical composition. Crystals however need higher melting temperatures; quartz for example has a melting point at around 1700 °C. Accordingly, the effect of ash on the operational reliability of aircraft turbines may not be judged solely based on knowledge commonly derived from mineral sand ingestion testing. In order to investigate the behaviour upon heating, we performed a series of experiments at ten temperature steps between 700 and 1600 °C. We used three different samples: 1) Ash from the explosive phase of Eyjafjallajökull; 2) MIL E-5007C test sand (MTS), and 3) Arizona Test Dust (ATD). MTS and ATD are commonly used for aircraft turbine testing. Experiments have been performed on two different grain sizes, < 63 and 90

Structure, properties, and surfactant adsorption behavior of fly ash carbon

NASA Astrophysics Data System (ADS)

Kulaots, Indrek

The objective of this research was to suggest methods by which certain problems associated with use of coal fly ash as a pozzolanic agent in concrete mixtures could be alleviated, guided by a better characterization of fly ash properties. A sample suite of eighty fly ashes was gathered from utilities across the world (mainly US-based) and included ashes from coals ranging in rank from bituminous to lignite. The widely used foam index test is used to characterize ashes with respect to their propensity to adsorb surfactants (called Air Entraining Admixtures or AEAs) used to impart freeze-thaw resistance to concrete. In ash-containing concrete mixtures, AEAs are adsorbed from the polar concrete-water solution onto non-polar unburned carbon surfaces in the ash. The AEA uptake by fly ashes only crudely correlates with the amount of carbon in the fly ash, because carbon surface area, accessibility and polarity all play a role in determining adsorption capacities. Fly ash carbon particle size distribution is also a key factor. Fine carbon particles in fly ash fractions of <106mum are responsible for about 90% of surfactant adsorption capacity. Surfactant adsorption on fly ash carbon is, in the foam index test, a dynamic process. The time of the test (typically <10 minutes) is not long enough to permit penetration of small porosity by the relatively large AEA molecules, and only the most readily available adsorption surface near the geometrical surface of the carbon particles is utilized. The nature of the foam index test was also examined, and it is recommended that a more standardized test procedure based upon pure reagents be adopted for examining the nature of fly ashes. Several possible reagents were identified. Room temperature fly ash ozonation is a powerful technique that allows increasing fly ash surface polarity in a relatively short time and thus is very effective for decreasing the AEA uptake capacity. Depending on the ozone input concentration, sample amount and contact time, surfactant uptake capacity decreases by a factor of two or more following reaction of only 0--1g O3/kg-ash, bringing many ashes into compliance with AEA uptake requirements.

Optical properties of volcanic ash: improving remote sensing observations.

NASA Astrophysics Data System (ADS)

Whelley, Patrick; Colarco, Peter; Aquila, Valentina; Krotkov, Nickolay; Bleacher, Jake; Garry, Brent; Young, Kelsey; Rocha Lima, Adriana; Martins, Vanderlei; Carn, Simon

2016-04-01

Many times each year explosive volcanic eruptions loft ash into the atmosphere. Global travel and trade rely on aircraft vulnerable to encounters with airborne ash. Volcanic ash advisory centers (VAACs) rely on dispersion forecasts and satellite data to issue timely warnings. To improve ash forecasts model developers and satellite data providers need realistic information about volcanic ash microphysical and optical properties. In anticipation of future large eruptions we can study smaller events to improve our remote sensing and modeling skills so when the next Pinatubo 1991 or larger eruption occurs, ash can confidently be tracked in a quantitative way. At distances >100km from their sources, drifting ash plumes, often above meteorological clouds, are not easily detected from conventional remote sensing platforms, save deriving their quantitative characteristics, such as mass density. Quantitative interpretation of these observations depends on a priori knowledge of the spectral optical properties of the ash in UV (>0.3μm) and TIR wavelengths (>10μm). Incorrect assumptions about the optical properties result in large errors in inferred column mass loading and size distribution, which misguide operational ash forecasts. Similarly, simulating ash properties in global climate models also requires some knowledge of optical properties to improve aerosol speciation.

Availability of residual phosphorus from broiler litter ash and layer manure ash amended soil for Paspalum vaginatum uptake

USDA-ARS?s Scientific Manuscript database

It has been hypothesized by several scientists that poultry litter ash could be used as a slow releasing phosphorus fertilizer that will become available over time. To test this hypothesis, a greenhouse study was conducted using a broiler litter ash, layer manure ash and calcium phosphate to determ...

Kangaroo rat bone compared to white rat bone after short-term disuse and exercise

USGS Publications Warehouse

Muths, E.; Reichman, O. J.

1996-01-01

Kangaroo rats (Dipodomys ordii) were used to study the effects of confinement on mechanical properties of bone with a long range objective of proposing an alternative to the white rat model for the study of disuse osteoporosis. Kangaroo rats exhibit bipedal locomotion, which subjects their limbs to substantial accelerative forces in addition to the normal stress of weight bearing. We subjected groups of kangaroo rats and white rats (Rattus norvegicus) to one of two confinement treatments or to an exercise regime; animals were exercised at a rate calculated to replicate their (respective) daily exercise patterns. White laboratory rats were used as the comparison because they are currently the accepted model used in the study of disuse osteoporosis. After 6 weeks of treatment, rats were killed and the long bones of their hind limbs were tested mechanically and examined for histomorphometric changes. We found that kangaroo rats held in confinement had less ash content in their hind limbs than exercised kangaroo rats. In general, treated kangaroo rats showed morphometric and mechanical bone deterioration compared to controls and exercised kangaroo rats appeared to have slightly “stronger” bones than confined animals. White rats exhibited no significant differences between treatments. These preliminary results suggest that kangaroo rats may be an effective model in the study of disuse osteoporosis.

Experimental Study on Semi-Dry Flue Gas Desulfurization Ash Used in Steel Slag Composite Material

NASA Astrophysics Data System (ADS)

Lu, Lijun; Fang, Honghui

This article carried out the experimental study on using desulfurization ash in steel slag composite material. This was done by investigating the desulfurization ash content in formula one and formula two samples on the influence of setting time and strength of mortar. Through this study the following conclusions were reached for formula one: (1) a setting time of more than 10 hours is required, (2) a dosage of desulfurization ash of 1 2% is optimal, where flexural strength is reduced by 10% 23% and compressive strength reduced by 5.7% 16.4%. The conclusions of formula two were: (1) when the dosage of desulfurization ash is within 5%, the setting time is within 10 hours; (2) when the dosage of desulfurization ash is 1 2%, the flexural strength is increased by 5 7% and the compressive strength is reduced by 1 2%. The results show that the formula two is better.

Effects of cutting time, stump height, and herbicide application on ash (Fraxinus spp.) stump sprouting and colonization by emerald ash borer (Agrilus planipennis)

Treesearch

Toby R. Petrice; Robert A. Haack

2011-01-01

Efforts to eradicate or slow the spread of emerald ash borer (EAB) (Agrilus planipennis Fairmaire [Coleoptera: Buprestidae]) include cutting infested and nearby uninfested ash (Fraxinus spp.) trees. However, ash trees readily sprout after they have been cut, providing potential host material for EAB. In 2004-2005, we conducted...

Viscoelastic behavior of basaltic ash from Stromboli volcano inferred from intermittent compression experiments

NASA Astrophysics Data System (ADS)

Kurokawa, A. K.; Miwa, T.; Okumura, S.; Uesugi, K.

2017-12-01

After ash-dominated Strombolian eruption, considerable amount of ash falls back to the volcanic conduit forming a dense near-surface region compacted by weights of its own and other fallback clasts (Patrick et al., 2007). Gas accumulation below this dense cap causes a substantial increase in pressure within the conduit, causing the volcanic activity to shift to the preliminary stages of a forthcoming eruption (Del Bello et al., 2015). Under such conditions, rheology of the fallback ash plays an important role because it controls whether the fallback ash can be the cap. However, little attention has been given to the point. We examined the rheology of ash collected at Stromboli volcano via intermittent compression experiments changing temperature and compression time/rate. The ash deformed at a constant rate during compression process, and then it was compressed without any deformation during rest process. The compression and rest processes repeated during each experiment to see rheological variations with progression of compaction. Viscoelastic changes during the experiment were estimated by Maxwell model. The results show that both elasticity and viscosity increases with decreasing porosity. On the other hand, the elasticity shows strong rate-dependence in the both compression and rest processes while the viscosity dominantly depends on the temperature, although the compression rate also affects the viscosity in the case of the compression process. Thus, the ash behaves either elastically or viscously depending on experimental process, temperature, and compression rate/time. The viscoelastic characteristics can be explained by magnitude relationships between the characteristic relaxation times and times for compression and rest processes. This indicates that the balance of the time scales is key to determining the rheological characteristics and whether the ash behaves elastically or viscously may control cyclic Strombolian eruptions.

Reuse of Coconut Shell, Rice Husk, and Coal Ash Blends in Geopolymer Synthesis

NASA Astrophysics Data System (ADS)

Walmiki Samadhi, Tjokorde; Wulandari, Winny; Prasetyo, Muhammad Iqbal; Rizki Fernando, Muhammad

2017-10-01

Mixtures of biomass and coal ashes are likely to be produced in increasing volume as biomass-based energy production is gaining importance in Indonesia. This work highlights the reuse of coconut shell ash (CSA), rice husk ash (RHA), and coal fly ash (FA) for geopolymer synthesis by an activator solution containing concentrated KOH and Na2SiO3. Ash blend compositions are varied according to a simplex-centroid mixture experimental design. Activator to ash mass ratios are varied from 0.8 to 2.0, the higher value being applied for ash compositions with higher Si/Al ratio. The impact of ash blend composition on early strength is adequately modeled by an incomplete quadratic mixture model. Overall, the ashes can produce geopolymer mortars with an early strength exceeding the Indonesian SNI 15-2049-2004 standard minimum value of 2.0 MPa. Good workability of the geopolymer is indicated by their initial setting times which are longer than the minimum value of 45 mins. Geopolymers composed predominantly of RHA composition exhibit poor strength and excessive setting time. FTIR spectroscopy confirms the geopolymerization of the ashes by the shift of the Si-O-Si/Al asymmetric stretching vibrational mode. Overall, these results point to the feasibility of geopolymerization as a reuse pathway for biomass combustion waste.

Formation of Humic Substances in Weathered MSWI Bottom Ash

PubMed Central

Zhang, Haixia; Shimaoka, Takayuki

2013-01-01

The study aimed at evaluating the humic substances (HSs) content from municipal solid waste incinerator (MSWI) bottom ash and its variation with time and the effect of temperature on HSs formation. The process suggested by IHSS was applied to extract HSs from two different bottom ash samples, and the extracted efficiency with NaOH and Na4P2O7 was compared. MSWI bottom ash samples were incubated at 37°C and 50°C for 1 year. HSs and nonhumic substances were extracted from the bottom ash sample with different incubated period by 0.1 M NaOH/Na4P2O7. Results show that the rate of humic acid formation increased originally with incubation time, reached a maximum at 12th week under 37°C and at 18th week under 50°C, and then decreased with time. More humic acid in MSWI bottom ash was formed under 50°C incubated condition compared with that incubated under 37°C. Also, the elemental compositions of HSs extracted from bottom ash are reported. PMID:23844394

Adsorption of malachite green dye from aqueous solution on the bamboo leaf ash

NASA Astrophysics Data System (ADS)

Kuntari, Priwidyanjati, Dessyntha Anggiani

2017-12-01

Bamboo leaf ash has been developed as an adsorbent material for removal malachite green from aqueous solution. Adsorption parameters have studied are contact time and initial pH. The effect of contact time and pH were examined in the batch adsorption processes. The physicochemical characters of bamboo leaf ash were investigated by using X-Ray Diffraction (XRD) and FT-IR spectroscopy. Malachite green concentration was determined by UV-Vis spectrophotometer. FT-IR spectrogram of bamboo leaf ash shows that typical fingerprint of adsorbent material with Si-O-Si or Al-O-Al group. The X-ray diffractograms of bamboo leaf ash show that adsorbent material has a highly amorphous nature. The percentage of adsorption was showed raised with increasing contact time. The optimum removal of malachite green when the initial dye concentration, initial pH, weight of adsorbent and contact time was 20 mg/L, 7, 0.25 g and 75 minutes respectively.

Stratigraphy, sedimentology and inferred flow dynamics from the July 2015 block-and-ash flow deposits at Volcán de Colima, Mexico

NASA Astrophysics Data System (ADS)

Macorps, Elodie; Charbonnier, Sylvain J.; Varley, Nick R.; Capra, Lucia; Atlas, Zachary; Cabré, Josep

2018-01-01

The July 2015 block-and-ash flow (BAF) events represent the first documented series of large-volume and long-runout BAFs generated from sustained dome collapses at Volcán de Colima. This eruption is particularly exceptional at this volcano due to (1) the large volume of BAF material emplaced (0.0077 ± 0.001 km3), (2) the long runout reached by the associated BAFs (max. 10 km), and (3) the short period ( 18 h) over which two main long-sustained dome collapse events occurred (on 10 and 11 July, respectively). Stratigraphy and sedimentology of the 2015 BAF deposits exposed in the southern flank of the volcano based on lithofacies description, grain size measurements and clast componentry allowed the recognition of three main deposit facies (i.e., valley-confined, overbank and ash-cloud surge deposits). Correlations and lithofacies variations inside three main flow units from both the valley-confined and overbank deposits left from the emplacement of the second series of BAFs on 11 July provide detailed information about: (1) the distribution, volumes and sedimentological characteristics of the different units; (2) flow parameters (i.e., velocity and dynamic pressure) and mobility metrics as inferred from associated deposits; and (3) changes in the dynamics of the different flows and their material during emplacement. These data were coupled with geomorphic analyses to assess the role of the topography in controlling the behaviour and impacts of the successive BAF pulses on the volcano flanks. Finally, these findings are used to propose a conceptual model for transport and deposition mechanisms of the July 2015 BAFs at Volcán de Colima. In this model, deposition occurs by rapid stepwise aggradation of successive BAF pulses. Flow confinement in a narrow and sinuous channel enhance the mobility and runout of individual channelized BAF pulses. When these conditions occur, the progressive valley infilling from successive sustained dome-collapse events promote the overspill and lateral spreading of the upper and marginal regions of the main flow body, generating highly mobile overbank flows that travel outside of the main valley. Volume- and distance-dependent critical channel capacities for the generation of overbank flows are used to better estimate the inundation area of these hazardous unconfined pyroclastic flows. These results highlight the importance of including and correctly assessing the hazards posed by large volume and long runout BAFs associated with frequent, small VEI, sustained dome-collapse eruptions.

Effect of chemical admixtures on properties of high-calcium fly ash geopolymer

NASA Astrophysics Data System (ADS)

Rattanasak, Ubolluk; Pankhet, Kanokwan; Chindaprasirt, Prinya

2011-06-01

Owing to the high viscosity of sodium silicate solution, fly ash geopolymer has the problems of low workability and rapid setting time. Therefore, the effect of chemical admixtures on the properties of fly ash geopolymer was studied to overcome the rapid set of the geopolymer in this paper. High-calcium fly ash and alkaline solution were used as starting materials to synthesize the geopolymer. Calcium chloride, calcium sulfate, sodium sulfate, and sucrose at dosages of 1wt% and 2wt% of fly ash were selected as admixtures based on concrete knowledge to improve the properties of the geopolymer. The setting time, compressive strength, and degree of reaction were recorded, and the microstructure was examined. The results show that calcium chloride significantly shortens both the initial and final setting times of the geopolymer paste. In addition, sucrose also delays the final setting time significantly. The degrees of reaction of fly ash in the geopolymer paste with the admixtures are all higher than those of the control paste. This contributes to the obvious increases in compressive strength.

Preliminary investigation of the effects of eruption source parameters on volcanic ash transport and dispersion modeling using HYSPLIT

NASA Astrophysics Data System (ADS)

Stunder, B.

2009-12-01

Atmospheric transport and dispersion (ATD) models are used in real-time at Volcanic Ash Advisory Centers to predict the location of airborne volcanic ash at a future time because of the hazardous nature of volcanic ash. Transport and dispersion models usually do not include eruption column physics, but start with an idealized eruption column. Eruption source parameters (ESP) input to the models typically include column top, eruption start time and duration, volcano latitude and longitude, ash particle size distribution, and total mass emission. An example based on the Okmok, Alaska, eruption of July 12-14, 2008, was used to qualitatively estimate the effect of various model inputs on transport and dispersion simulations using the NOAA HYSPLIT model. Variations included changing the ash column top and bottom, eruption start time and duration, particle size specifications, simulations with and without gravitational settling, and the effect of different meteorological model data. Graphical ATD model output of ash concentration from the various runs was qualitatively compared. Some parameters such as eruption duration and ash column depth had a large effect, while simulations using only small particles or changing the particle shape factor had much less of an effect. Some other variations such as using only large particles had a small effect for the first day or so after the eruption, then a larger effect on subsequent days. Example probabilistic output will be shown for an ensemble of dispersion model runs with various model inputs. Model output such as this may be useful as a means to account for some of the uncertainties in the model input. To improve volcanic ash ATD models, a reference database for volcanic eruptions is needed, covering many volcanoes. The database should include three major components: (1) eruption source, (2) ash observations, and (3) analyses meteorology. In addition, information on aggregation or other ash particle transformation processes would be useful.

A regional assessment of emerald ash borer impacts in the Eastern United States: ash mortality and abundance trends in time and space

Treesearch

Randall S. Morin; Scott A. Pugh; Andrew M. Liebhold; Susan J. Crocker

2015-01-01

The nonnative insect, emerald ash borer (Agrilus plannipennis Fairmaire), has caused extensive mortality of ash tree species (Fraxinus spp.) in the eastern United States. As of 2012, the pest had been detected in about 15 percent of the counties in the 37 states that comprise the natural range of ash in forests of the eastern...

Investigating Electrostatic Precipitator Design Parameters for Efficient Control of Particulate Matter in Thermal Power Plant: A Case Study

NASA Astrophysics Data System (ADS)

Rai, P.; Gautam, N.; Chandra, H.

2018-06-01

This work deals with the analysis and modification of operational parameters for meeting the emission standards, set by Central Pollution Control Board (CPCB)/State Pollution Control Board (SPCB) from time to time of electrostatic precipitator (ESP). The analysis is carried out by using standard chemical analysis supplemented by the relevant data collected from Korba East Phase (Ph)-III thermal power plant, under Chhattisgarh State Electricity Board (CSEB) operating at Korba, Chhattisgarh. Chemical analysis is used to predict the emission level for different parameters of ESP. The results reveal that for a constant outlet PM concentration and fly ash percentage, the total collection area decreases with the increase in migration velocity. For constant migration velocity and outlet PM concentration, the total collection area increases with the increase in the fly ash percent. For constant migration velocity and outlet e PM concentration, the total collection area increases with the ash content in the coal. i.e. from minimum ash to maximum ash. As far as the efficiency is concerned, it increases with the fly ash percent, ash content and the inlet dust concentration but decreases with the outlet PM concentration at constant migration velocity, fly ash and ash content.

Investigating Electrostatic Precipitator Design Parameters for Efficient Control of Particulate Matter in Thermal Power Plant: A Case Study

NASA Astrophysics Data System (ADS)

Rai, P.; Gautam, N.; Chandra, H.

2018-02-01

This work deals with the analysis and modification of operational parameters for meeting the emission standards, set by Central Pollution Control Board (CPCB)/State Pollution Control Board (SPCB) from time to time of electrostatic precipitator (ESP). The analysis is carried out by using standard chemical analysis supplemented by the relevant data collected from Korba East Phase (Ph)-III thermal power plant, under Chhattisgarh State Electricity Board (CSEB) operating at Korba, Chhattisgarh. Chemical analysis is used to predict the emission level for different parameters of ESP. The results reveal that for a constant outlet PM concentration and fly ash percentage, the total collection area decreases with the increase in migration velocity. For constant migration velocity and outlet PM concentration, the total collection area increases with the increase in the fly ash percent. For constant migration velocity and outlet e PM concentration, the total collection area increases with the ash content in the coal. i.e. from minimum ash to maximum ash. As far as the efficiency is concerned, it increases with the fly ash percent, ash content and the inlet dust concentration but decreases with the outlet PM concentration at constant migration velocity, fly ash and ash content.

Evaluation of reference genes for expression studies in ash (Fraxinus spp.)

Treesearch

Loren Rivera-Vega; Praveen Mamidala; Jennifer L. Koch; Mary E. Mason; Omprakash Mittapalli

2012-01-01

Ash (Fraxinus spp.) is a dominant tree species in North America, in both managed and natural landscapes. However, due to the rapid invasion by the emerald ash borer (Agrilus planipennis), an exotic invasive insect pest, millions of North American ash trees have been killed. Real-time quantitative polymerase chain reaction (RTq-PCR...

Cumulative effects of volcanic ash on the food preferences of two Orthopteran species.

PubMed

Fernández-Arhex, Valeria; Amadio, Maria E; Bruzzone, Octavio A

2017-08-01

Inert dusts are an early form of insecticide which is still in use. One of the most common inert dusts is volcanic ash. In order to study the reaction of rangeland grasshoppers, Dichroplus vittigerum (Acrididae) and a katydid, Burgilis mendosensis (Phaneropteridae), to the presence of volcanic ash in their food sources and how this reaction changed as a function of time, we conducted paired preference tests between clean leaves of their preferred host plant and leaves exposed to volcanic ash of different grain size. The behavioral response was measured as the rating on the Thurstonian preference scale of leaves with ash in relation to clean leaves. The results showed that the avoidance of volcanic ash increased as a function of time in both species. Both species studied are occasionally exposed to volcanic activity, and come from an area in which a volcanic eruption had recently occurred. As their populations did not decrease after the ash fall, we propose that some behavioral responses such as avoidance of places with ash, works as tolerance mechanism to inert dusts exposure. © 2016 Institute of Zoology, Chinese Academy of Sciences.

Comparison of heterogeneous photolytic reduction of Hg(II) in the coal fly ashes and synthetic aerosols

NASA Astrophysics Data System (ADS)

Tong, Yindong; Eichhorst, Terry; Olson, Michael R.; Rutter, Andrew P.; Shafer, Martin M.; Wang, Xuejun; Schauer, James J.

2014-03-01

In this study, we examined the heterogeneous reduction of Hg(II) on the coal fly ash samples and synthetic aerosols under different light conditions in a controlled laboratory reactor. Three types of coal fly ashes were studied: a high carbon fly ash from a stoker boiler, a low carbon/low sulfate fly ash from a pulverized coal combustor burning low sulfur coal, and a high sulfate fly ash from a pulverized coal combustor burning high sulfur coal. The rate of Hg(II) reduction on the three diverse fly ash samples was found to be relatively fast with an average half-life of 1.6 h under clear sky atmospheric conditions (under the irradiance of 1000 W/m2). The reduction rate in the low sulfate/low carbon fly ash was approximately 1.5 times faster than with the other coal fly ash samples. Synthetic aerosols made of carbon black and levoglucosan produced Hg(II) reduction rates similar to coal fly ashes. However, aerosols composed of adipic acid resulted in reduction rates that were 3-5 times faster. The sensitivity of adipic acid reduction to light source wavelength was found to be greater than for the coal fly ash and other synthetic aerosols. Aerosols made from the water extracts of coal fly ash samples produced reduction rates equal to or slightly higher than with the native fly ash suggesting that the soluble components of fly ash play a significant role in the reduction mechanism. The measured reduction rates are likely important in the chemical processing of mercury in power plant plumes and potentially in the atmosphere and should be considered for incorporation in atmospheric transport models that are used to understand the fate of atmospheric mercury.

Natural weathering in dry disposed ash dump: Insight from chemical, mineralogical and geochemical analysis of fresh and unsaturated drilled cores.

PubMed

Akinyemi, S A; Akinlua, A; Gitari, W M; Khuse, N; Eze, P; Akinyeye, R O; Petrik, L F

2012-07-15

Some existing alternative applications of coal fly ash such as cement manufacturing; road construction; landfill; and concrete and waste stabilisation use fresh ash directly collected from coal-fired power generating stations. Thus, if the rate of usage continues, the demand for fresh ash for various applications will exceed supply and use of weathered dry disposed ash will become necessary alternative. As a result it's imperative to understand the chemistry and pH behaviour of some metals inherent in dry disposed fly ash. The bulk chemical composition as determined by XRF analysis showed that SiO2, Al2O3 and Fe2O3 were the major oxides in fresh ash and unsaturated weathered ashes. The unsaturated weathered ashes are relatively depleted in CaO, Fe2O3, TiO2, SiO2, Na2O and P2O5 due to dissolution and hydrolysis caused by chemical interaction with ingressing CO2 from the atmosphere and infiltrating rain water. Observed accumulations of Fe2O3, TiO2, CaO, K2O, Na2O and SO3 and Zn, Zr, Sr, Pb, Ni, Cr and Co in the lower layers indicate progressive downward movement through the ash dump though at a slow rate. The bulk mineralogy of unsaturated weathered dry disposed ash, as determined by XRD analysis, revealed quartz and mullite as the major crystalline phases; while anorthite, hematite, enstatite, lime, calcite, and mica were present as minor mineral phases. Pore water chemistry revealed a low concentration of readily soluble metals in unsaturated weathered ashes in comparison with fresh ash, which shows high leachability. This suggests that over time the precipitation of transient minor secondary mineral phases; such as calcite and mica might retard residual metal release from unsaturated weathered ash. Chloride and sulphate species of the water soluble extracts of weathered ash are at equilibrium with Na+ and K+; these demonstrate progressive leaching over time and become supersaturated at the base of unsaturated weathered ash. This suggests that the ash dump does not encapsulate the salt or act as a sustainable salt sink due to over time reduction in pore water pH. The leaching behaviours of Ca, Mg, Na+, K+, Se, Cr and Sr are controlled by the pH of the leachant in both fresh and unsaturated weathered ash. Other trace metals like As, Mo and Pb showed amphoteric behaviour with respect to the pH of the leachant. The precipitation of minor quantities of secondary mineral phases in the unsaturated weathered ash has significant effects on the acid susceptibility and leaching patterns of chemical species in comparison with fresh ash. The unsaturated weathered ash had lower buffering capacity at neutral pH (7.94-8.00) compared to fresh (unweathered) ash. This may be due to the initial high leaching/flushing of soluble basic buffering constituents from fly ash after disposal. The overall results of the acid susceptibility tests suggest that both fresh ash and unsaturated weathered ash would release a large percentage of their chemical species when in contact with slightly acidified rain. Proper management of ash dumps is therefore essential to safeguard the environmental risks of water percolation in different fly ashes behaviour. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effects of ambient temperature on egg and larval development of the invasive emerald ash borer (Coleoptera: Buprestidae): implications for laboratory rearing.

PubMed

Duan, Jian J; Watt, Tim; Taylor, Phil; Larson, Kristi; Lelito, Jonathan P

2013-10-01

The emerald ash borer, Agrilus planipennis Fairmaire, an invasive beetle from Asia causing large scale ash (Fraxinus) mortality in North America, has been extremely difficult to rear in the laboratory because of its long life cycle and cryptic nature of immature stages. This lack of effective laboratory-rearing methods has not only hindered research into its biology and ecology, but also mass production of natural enemies for biological control of this invasive pest. Using sticks from the alternate host plant, Fraxinus uhdei (Wenzig) Lingelsh, we characterized the stage-specific development time and growth rate of both emerald ash borer eggs and larvae at different constant temperatures (12-35 degrees C) for the purpose of developing effective laboratory-rearing methods. Results from our study showed that the median time for egg hatching decreased from 20 d at 20 degrees C to 7 d at 35 degrees C, while no emerald ash borer eggs hatched at 12 degrees C. The developmental time for 50% of emerald ash borer larvae advancing to third, fourth, and J-larval stages at 20 degrees C were 8.3, 9.1, and 12.3 wk, respectively, approximately two times longer than at 30 degrees C for the corresponding instars or stages. In contrast to 30 degrees C, however, the development times of emerald ash borer larvae advancing to later instars (from oviposition) were significantly increased at 35 degrees C, indicating adverse effects of this high temperature. The optimal range of ambient temperature to rear emerald ash borer larvae should be between 25-30 degrees C; however, faster rate of egg and larval development should be expected as temperature increases within this range.

Optimizing use of girdled ash trees for management of low-density emerald ash borer (Coleoptera: Buprestidae) populations

Treesearch

Nathan W. Siegert; Deborah G. McCullough; Therese M. Poland; Robert L. Heyd

2017-01-01

Effective survey methods to detect and monitor recently established, low-density infestations of emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), remain a high priority because they provide land managers and property owners with time to implement tactics to slow emerald ash borer population growth and the progression of...

Control of ITBs in Magnetically Confined Burning Plasmas

NASA Astrophysics Data System (ADS)

Panta, S. R.; Newman, D. E.; Terry, P. W.; Sanchez, R.

2017-10-01

In the magnetically confined burning plasma devices (in this case Tokamaks), internal transport barriers (ITBs) are those regimes in which the turbulence is suppressed by the E X B velocity shear, reducing the turbulent transport. This often occurs at a critical gradient in the profiles. The change in the transport then modifies the density and temperature profiles feeding back on the system. These transport barriers have to be controlled both to form them for improved confinement and remove them to both prevent global instabilities and to remove the ash and unnecessary impurities in the device. In this work we focus on pellet injection and modulated RF heating as a way to trigger and control the ITBs. These have an immediate consequence on density and temperature and hence pressure profiles acting as a control knob. For example, depending upon pellet size and its radial position of injection, it either helps to form or strengthen the barrier or to get rid of ITBs in the different transport channels of the burning plasmas. This transport model is then used to investigate the control and dynamics of the transport barriers in burning plasmas using pellets and RF addition to the NBI power and alpha power.

Failure to phytosanitize ash firewood infested with emerald ash borer in a small dry kiln using ISPM-15 standards.

PubMed

Goebel, P Charles; Bumgardner, Matthew S; Herms, Daniel A; Sabula, Andrew

2010-06-01

Although current USDA-APHIS standards suggest that a core temperature of 71.1 degrees C (160 degrees F) for 75 min is needed to adequately sanitize emerald ash borer, Agrilus planipennis Fairmaire-infested firewood, it is unclear whether more moderate (and economical) treatment regimes will adequately eradicate emerald ash borer larvae and prepupae from ash firewood. We constructed a small dry kiln in an effort to emulate the type of technology a small- to medium-sized firewood producer might use to examine whether treatments with lower temperature and time regimes successfully eliminate emerald ash borer from both spilt and roundwood firewood. Using white ash (Fraxinus americana L.) firewood collected from a stand with a heavy infestation of emerald ash borer in Delaware, OH, we treated the firewood using the following temperature and time regime: 46 degrees C (114.8 degrees F) for 30 min, 46 degrees C (114.8 degrees F) for 60 min, 56 degrees C (132.8 degrees F) for 30 min, and 56 degrees C (132.8 degrees F) for 60 min. Temperatures were recorded for the outer 2.54-cm (1-in.) of firewood. After treatment, all firewood was placed under mesh netting and emerald ash borer were allowed to develop and emerge under natural conditions. No treatments seemed to be successful at eliminating emerald ash borer larvae and perpupae as all treatments (including two nontreated controls) experienced some emerald ash borer emergence. However, the 56 degrees C (132.8 degrees F) treatments did result in considerably less emerald ash borer emergence than the 46 degrees C (114.8 degrees F) treatments. Further investigation is needed to determine whether longer exposure to the higher temperature (56 degrees C) will successfully sanitize emerald ash borer-infested firewood.

Biomass ashes from pyrolytic wood liquefaction as novel soil amendments

NASA Astrophysics Data System (ADS)

Fernández-Delgado Juárez, Marina; Gómez Brandón, María; Mazzier, Thomas; Schönegger, Deborah; Hermanns, Roy; Leijenhorst, Evert; Insam, Heribert

2017-04-01

What happens when an old soil amendment is in fact a new one? Traditionally, ashes from biomass combustion were considered as a valuable resource, and widely used as an agricultural soil amendment. However, in recent decades we have been reluctant to apply them to soils, despite the increase in the production of combustion ashes resulting from the development of new fuels derived from biomass residues. The production of Fast Pyrolysis Bio Oil (FPBO) out of various lignocellulosic biomass streams is one of the newest technologies for gaining a liquid biofuel that can be seen as a future substitute for mineral oils. During the pyrolysis process, the by-products (charcoal and low calorific gases) are combusted to generate energy, resulting in the production of ashes that contain the majority of the minerals and salts originally present in the feedstock. The main objective of the present work is to investigate if the recovered ashes from the pyrolysis process can be used as a soil amendment. A greenhouse trial was set up in order to evaluate the impact of the ashes on an acid grassland soil (eutric Cambisol) from the region of Tyrol (Austria). A two-level experimental design (ash treatment, and plant effect) was set up. The ashes were mixed with the soil columns at a ratio of 1% (w:w, fresh weight). A control treatment that consisted of soil without the addition of ashes was also included. Moreover, to understand the effect that the ashes would have on crop growth, ten seeds of a traditional wheat variety (Tiroler Früher Dinkel; Triticum aestivum subsp. spelta), were placed in half of the columns with and without ashes, so as to determine the seed germination index and plant growth. Moreover, specific microbial groups related to N cycle were quantified by real-time PCR. A total of 24 experimental units (2 ash treatments x 2 incubation times x 2 plant levels x 3 replicates) were analysed. After an equilibration period of 24 h at 4 °C (referred as time zero), the columns were arranged in a completely randomized design and destructively sampled after 60 and 100 days. The amendment with ashes induced a soil pH increase of almost 2 units over time and independent of the crop presence. Moreover, ash addition did also increase soil plant available P and dissolved organic carbon content; however, it also increased nitrogen loss to the soil eluates compared to the control. On the other hand, the presence of ashes enhanced both plant growth and grain yield after 60 and 100 days. Similar effects have been observed when "traditional" biomass ashes have been applied to agricultural soils, leading us to conclude that ashes derived from FPBO process might be used for agricultural purposes. The Residue2Heat project has received funding from the European Union's Horizon 2020 Research and Innovation programme under Grant Agreement No. 654650.

Real-Time Estimation of Volcanic ASH/SO2 Cloud Height from Combined Uv/ir Satellite Observations and Numerical Modeling

NASA Astrophysics Data System (ADS)

Vicente, Gilberto A.

An efficient iterative method has been developed to estimate the vertical profile of SO2 and ash clouds from volcanic eruptions by comparing near real-time satellite observations with numerical modeling outputs. The approach uses UV based SO2 concentration and IR based ash cloud images, the volcanic ash transport model PUFF and wind speed, height and directional information to find the best match between the simulated and the observed displays. The method is computationally fast and is being implemented for operational use at the NOAA Volcanic Ash Advisory Centers (VAACs) in Washington, DC, USA, to support the Federal Aviation Administration (FAA) effort to detect, track and measure volcanic ash cloud heights for air traffic safety and management. The presentation will show the methodology, results, statistical analysis and SO2 and Aerosol Index input products derived from the Ozone Monitoring Instrument (OMI) onboard the NASA EOS/Aura research satellite and from the Global Ozone Monitoring Experiment-2 (GOME-2) instrument in the MetOp-A. The volcanic ash products are derived from AVHRR instruments in the NOAA POES-16, 17, 18, 19 as well as MetOp-A. The presentation will also show how a VAAC volcanic ash analyst interacts with the system providing initial condition inputs such as location and time of the volcanic eruption, followed by the automatic real-time tracking of all the satellite data available, subsequent activation of the iterative approach and the data/product delivery process in numerical and graphical format for operational applications.

Surface reactivity of volcanic ash from the eruption of Soufrière Hills volcano, Montserrat, West Indies with implications for health hazards.

PubMed

Horwell, Claire J; Fenoglio, Ivana; Vala Ragnarsdottir, K; Sparks, R Steve J; Fubini, Bice

2003-10-01

The fine-grained character of volcanic ash generated in the long-lived eruption of the Soufrière Hills volcano, Montserrat, West Indies, raises the issue of its possible health hazards. Surface- and free-radical production has been closely linked to bioreactivity of dusts within the lung. In this study, electron paramagnetic resonance (EPR) techniques have been used, for the first time, on volcanic ash to measure the production of radicals from the surface of particles. Results show that concentrations of hydroxyl radicals (HO*) in respirable ash are two to three times higher than a toxic quartz standard. The dome-collapse ash contains cristobalite, a crystalline silica polymorph that may cause adverse health effects. EPR experiments indicate, however, that cristobalite in the ash does not contribute to HO* generation. Our results show that the main cause of reactivity is removable divalent iron (Fe2+), which is present in abundance on the surfaces of the particles and is very reactive in the lung. Our analyses show that fresh ash generates more HO* than weathered ash (which has undergone progressive oxidation and leaching of iron from exposed surfaces), an effect replicated experimentally by incubating fresh ash in dilute acid. HO* production experiments also indicate that iron-rich silicate minerals are responsible for surface reactivity in the Soufrière Hills ash.

Quantifying volcanic ash dispersal and impact of the Campanian Ignimbrite super-eruption

NASA Astrophysics Data System (ADS)

Costa, A.; Folch, A.; Macedonio, G.; Giaccio, B.; Isaia, R.; Smith, V. C.

2012-05-01

We apply a novel computational approach to assess, for the first time, volcanic ash dispersal during the Campanian Ignimbrite (Italy) super-eruption providing insights into eruption dynamics and the impact of this gigantic event. The method uses a 3D time-dependent computational ash dispersion model, a set of wind fields, and more than 100 thickness measurements of the CI tephra deposit. Results reveal that the CI eruption dispersed 250-300 km3 of ash over ˜3.7 million km2. The injection of such a large quantity of ash (and volatiles) into the atmosphere would have caused a volcanic winter during the Heinrich Event 4, the coldest and driest climatic episode of the Last Glacial period. Fluorine-bearing leachate from the volcanic ash and acid rain would have further affected food sources and severely impacted Late Middle-Early Upper Paleolithic groups in Southern and Eastern Europe.

Can Emerald ash borer, Agrilus planipennis (Coleoptera: Buprestidae), emerge from logs two summers after infested trees are cut?

Treesearch

Toby R. Petrice; Robert A. Haack

2007-01-01

Emerald ash borer (EAB), Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), is a serious invasive pest of ash trees (Fraxinus spp.) in North America. Much of EAB's range expansion has been attributed to human-assisted movement of infested items such as ash logs and firewood. It is unclear the amount of time that logs cut...

Nanoparticles of volcanic ash as a carrier for toxic elements on the global scale.

PubMed

Ermolin, Mikhail S; Fedotov, Petr S; Malik, Natalia A; Karandashev, Vasily K

2018-06-01

At present, there is concern about engineered nanoparticles in the environment, whereas natural nanoparticles (NPs) and their impact are often neglected. In our paper, we demonstrate the important role of nanoparticles of volcanic ash in transport of toxic elements on a global scale. A single volcanic eruption can eject millions of tons of ash. NPs of volcanic ash reach the upper troposphere and the stratosphere and may "travel" around the world for years affecting human health, environment, and even climate. So far, there is a gap in exposure assessment of volcanic ash NPs since their chemical composition remains largely unknown. Here we show for the first time that volcanic ash NPs can serve as an important carrier for potentially toxic elements. The concentrations of Ni, Zn, Cd, Ag, Sn, Se, Te, Hg, Tl, Pb, Bi in volcanic ash NPs (<100 nm) were found to be 10-500 times higher than total contents of these elements in bulk samples. This is valid for volcanoes from different regions of the world (Kamchatka, Far East of Russia and Andes, Chile). The work opens a new door into studies on biogeochemical impact of volcanic ash. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ash3d: A finite-volume, conservative numerical model for ash transport and tephra deposition

USGS Publications Warehouse

Schwaiger, Hans F.; Denlinger, Roger P.; Mastin, Larry G.

2012-01-01

We develop a transient, 3-D Eulerian model (Ash3d) to predict airborne volcanic ash concentration and tephra deposition during volcanic eruptions. This model simulates downwind advection, turbulent diffusion, and settling of ash injected into the atmosphere by a volcanic eruption column. Ash advection is calculated using time-varying pre-existing wind data and a robust, high-order, finite-volume method. Our routine is mass-conservative and uses the coordinate system of the wind data, either a Cartesian system local to the volcano or a global spherical system for the Earth. Volcanic ash is specified with an arbitrary number of grain sizes, which affects the fall velocity, distribution and duration of transport. Above the source volcano, the vertical mass distribution with elevation is calculated using a Suzuki distribution for a given plume height, eruptive volume, and eruption duration. Multiple eruptions separated in time may be included in a single simulation. We test the model using analytical solutions for transport. Comparisons of the predicted and observed ash distributions for the 18 August 1992 eruption of Mt. Spurr in Alaska demonstrate to the efficacy and efficiency of the routine.

Volcanic ash dosage calculator: A proof-of-concept tool to support aviation stakeholders during ash events

NASA Astrophysics Data System (ADS)

Dacre, H.; Prata, A.; Shine, K. P.; Irvine, E.

2017-12-01

The volcanic ash clouds produced by Icelandic volcano Eyjafjallajökull in April/May 2010 resulted in `no fly zones' which paralysed European aircraft activity and cost the airline industry an estimated £1.1 billion. In response to the crisis, the Civil Aviation Authority (CAA), in collaboration with Rolls Royce, produced the `safe-to-fly' chart. As ash concentrations are the primary output of dispersion model forecasts, the chart was designed to illustrate how engine damage progresses as a function of ash concentration. Concentration thresholds were subsequently derived based on previous ash encounters. Research scientists and aircraft manufactures have since recognised the importance of volcanic ash dosages; the accumulated concentration over time. Dosages are an improvement to concentrations as they can be used to identify pernicious situations where ash concentrations are acceptably low but the exposure time is long enough to cause damage to aircraft engines. Here we present a proof-of-concept volcanic ash dosage calculator; an innovative, web-based research tool, developed in close collaboration with operators and regulators, which utilises interactive data visualisation to communicate the uncertainty inherent in dispersion model simulations and subsequent dosage calculations. To calculate dosages, we use NAME (Numerical Atmospheric-dispersion Modelling Environment) to simulate several Icelandic eruption scenarios, which result in tephra dispersal across the North Atlantic, UK and Europe. Ash encounters are simulated based on flight-optimal routes derived from aircraft routing software. Key outputs of the calculator include: the along-flight dosage, exposure time and peak concentration. The design of the tool allows users to explore the key areas of uncertainty in the dosage calculation and to visualise how this changes as the planned flight path is varied. We expect that this research will result in better informed decisions from key stakeholders during volcanic ash events through a deeper understanding of the associated uncertainties in dosage calculations.

Group-V atoms exchange due to exposure of InP surface to AsH3(+PH3) revealed by x-ray CTR scattering

NASA Astrophysics Data System (ADS)

Tabuchi, M.; Yamada, N.; Fujibayashi, K.; Takeda, Y.; Kamei, H.

1996-05-01

We conducted x-ray crystal truncation rod (CTR) measurements using synchro-tron radiation to analyze the As atom distribution in InP to the order of 1 ML. The InP samples which were only exposed to AsH3(+PH3) and capped by InP were investigated to study the effect of the purge sequence. The purge sequence is unavoidable to grow heteroepitaxial layers by OMVPE and is considered to affect largely the structure of the interface. From the results of the measurement and the computer simulation, the distribution of P and As atoms of the order of 1 ML was discussed as functions of the exposing time. It was shown that the number of As atoms contained in the samples saturated when the AsH3-exposure time is longer than 10 s. Comparing the profiles of AsH3-exposed samples with that of (AsH3 + PH3)-exposed samples, it was found that the As distribution in the buffer layer was suppressed in (AsH3 + PH3)-exposed samples. In order to obtain the sharp interfaces, the AsH3-exposure time must be shorter than 0.5 s.

Demonstration of Regenerable, Large-Scale Ion Exchange System Using WBA Resin in Rialto, CA

DTIC Science & Technology

2012-12-01

requirements. The system also has the flexibility to manually modify system parameters such as flow rates, pH set points, time cycles, etc. The system... flexibility to produce soda ash solutions that vary in concentration from 1 to 10% dry soda ash. The packaged soda ash system was engineered and...The dry soda ash was conveyed to a storage hopper (39.5 ft3) using a flexible screw conveyer. Soda ash solutions were prepared in a 100 gallon

Multi-fuel combustor for gas turbine engines: Phase 1, Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melconian, J.O.; Marden, W.W., III

An innovative can combustor configuration has been developed for gas turbine engines which has the potential of burning fuels ranging from gasoline to coal/water slurries at high efficiencies. The design is based on a Variable Residence Time (VRT) concept which allows large and agglomerated fuel particles adequate time to completely burn. High durability of the combustor is achieved by dual function use of the incoming air. For applications which require the burning of coal/water slurries, the design has the capability of removing the ash particles directly from the primary zone of the combustor. It is anticipated that because of themore » small size requirement of this combustor design, existing gas turbine engines could be retrofitted within the confines of the current engine envelope. In Phase 1, the feasibility of the concept was successfully demonstrated by three-dimensional mathematical modeling and water analogue tests. The Plexiglas model used in the water analogue tests was designed to fit the current production engine of a major manufacturer. 19 figs., 2 tabs.« less

Resuspension of ash after the 2014 phreatic eruption at Ontake volcano, Japan

NASA Astrophysics Data System (ADS)

Miwa, Takahiro; Nagai, Masashi; Kawaguchi, Ryohei

2018-02-01

We determined the resuspension process of an ash deposit after the phreatic eruption of September 27th, 2014 at Ontake volcano, Japan, by analyzing the time series data of particle concentrations obtained using an optical particle counter and the characteristics of an ash sample. The time series of particle concentration was obtained by an optical particle counter installed 11 km from the volcano from September 21st to October 19th, 2014. The time series contains counts of dust particles (ash and soil), pollen, and water drops, and was corrected to calculate the concentration of dust particles based on a polarization factor reflecting the optical anisotropy of particles. The dust concentration was compared with the time series of wind velocity. The dust concentration was high and the correlation coefficient with wind velocity was positive from September 28th to October 2nd. Grain-size analysis of an ash sample confirmed that the ash deposit contains abundant very fine particles (< 30 μm). Simple theoretical calculations revealed that the daily peaks of the moderate wind (a few m/s at 10 m above the ground surface) were comparable with the threshold wind velocity for resuspension of an unconsolidated deposit with a wide range of particle densities. These results demonstrate that moderate wind drove the resuspension of an ash deposit containing abundant fine particles produced by the phreatic eruption. Histogram of polarization factors of each species experimentally obtained. The N is the number of analyzed particles.

Sintering of MSW fly ash for reuse as a concrete aggregate.

PubMed

Mangialardi, T

2001-10-12

The sintering process of municipal solid waste (MSW) fly ash was investigated in order to manufacture sintered products for reuse as concrete aggregates. Four types of fly ash resulting from different Italian MSW incineration plants were tested in this study. A modification of the chemical composition of MSW fly ash--through a preliminary four-stage washing treatment of this material with water--was attempted to improve the chemical and mechanical characteristics of sintered products.The sintering treatment of untreated or washed fly ash was performed on cylindrical compact specimens (15 mm in diameter and 20mm in height) at different compact pressures, sintering temperatures and times.The sintering process of untreated MSW fly ashes proved to be ineffective for manufacturing sintered products for reuse as a construction material, because of the adverse chemical characteristics of these fly ashes in terms of sulfate, chloride, and vitrifying oxide contents.A preliminary washing treatment of MSW fly ash with water greatly improved the chemical and mechanical characteristics of sintered products and, for all the types of fly ash tested, the sintered products satisfied the Italian requirements for normal weight aggregates for use in concretes having a specified strength not greater than 12 and 15N/mm(2), when measured on cylindrical and cubic specimens, respectively.A compact pressure of 28 N/mm(2), a sintering temperature of 1140 degrees C, and a sintering time of 60 min were the best operating conditions for manufacturing sintered products of washed MSW fly ash.

Toward quantitative forecasts of volcanic ash dispersal: Using satellite retrievals for optimal estimation of source terms

NASA Astrophysics Data System (ADS)

Zidikheri, Meelis J.; Lucas, Christopher; Potts, Rodney J.

2017-08-01

Airborne volcanic ash is a hazard to aviation. There is an increasing demand for quantitative forecasts of ash properties such as ash mass load to allow airline operators to better manage the risks of flying through airspace likely to be contaminated by ash. In this paper we show how satellite-derived mass load information at times prior to the issuance of the latest forecast can be used to estimate various model parameters that are not easily obtained by other means such as the distribution of mass of the ash column at the volcano. This in turn leads to better forecasts of ash mass load. We demonstrate the efficacy of this approach using several case studies.

Selenium content and oxidation states in fly ashes from western U.S. coals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattigod, Shas V; Quinn, Thomas R

2003-08-01

A selective extraction scheme was developed for the determination of the oxidation states of Se species in coal ashes. As compared to HF dissolution, extractions with 70% HC1O4 mobilized 90 to 100% of all compound and redox forms of Se from four of the five fly ashes. Extractions with 16M HNO3 did not mobilize all forms of Se as effectively as perchloric acid. Both oxidized forms of Se (IV and VI) were completely mobilized by 12M HCl extraction. Deionized-distilled water was not an effective extractant for mobilizing all compound forms of Se(IV) from fly ashes. Extraction data (70% HClO4, 16Mmore » HNO3, 12M HCl, DI water) indicated that the solid:solution ratio is a critical factor in Se extractability from fly ashes. Maximum extractions in all cases were obtained only with very high (1:500) solid:solution ratios. Extraction times from 1.5 to 25 hours did not significantly change Se extractability with any of the extractants except with 12M HCl, which required a minimum reaction time of 48 hours to attain maximum Se extractability. Reaction times shorter than the critical time and low solid:solution ratios significantly affected Se extractability from these fly ashes. Measurements of Se content and redox state in particle size and density fractions five western United States coal ashes indicated that typically, the Se content increased with decreasing particle size.. However, no consistent trend in Se concentration between the light and heavy density fractions of <2.7-m size fraction was observed. Selenium redox state data indicated that only Se(0) and Se(IV) forms were present in these five coal ashes. The presence of Se(IV) is significant since it is much more easily mobilized than the elemental form. Examination of fly ashes by the proposed scheme to determine Se redox species could permit better estimation of the Se content of plants grown on fly ash amended soils.« less

Leaching kinetics of As, Mo, and Se from acidic coal fly ash samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neupane, Ghanashyam; Donahoe, Rona J.; Bhattacharyya, Siddhartha

Annually, coal-fired electric power plants produce large volumes potentially hazardous coal combustion products (CCPs) including fly ash. Since majority of the coal fly ash and other CCPs deposited in dry land fills or wet lagoons, they pose risk of contamination to local environment and hydrogeology. In this study, we present results of leaching kinetics for As, Mo, and Se from three acidic fly ash samples. This study shows that the leachate concentrations of As, Mo, and Se increase over time. Three kinetics equations, pseudo-second order, Elovich, and power-function, are able to adequately describe the experimental leaching kinetics data. Experimental leachingmore » data and modeling results indicate that the rate limiting leaching of As, Mo, and Se is largely controlled by the dissolution of the fly ash particles. Furthermore, it is important to adopt effective containment/treatment schemes to avoid potential and persistent dispersion of trace elements from ash disposal facilities to surrounding environment for a long time.« less

Leaching kinetics of As, Mo, and Se from acidic coal fly ash samples

DOE PAGES

Neupane, Ghanashyam; Donahoe, Rona J.; Bhattacharyya, Siddhartha; ...

2017-07-03

Annually, coal-fired electric power plants produce large volumes potentially hazardous coal combustion products (CCPs) including fly ash. Since majority of the coal fly ash and other CCPs deposited in dry land fills or wet lagoons, they pose risk of contamination to local environment and hydrogeology. In this study, we present results of leaching kinetics for As, Mo, and Se from three acidic fly ash samples. This study shows that the leachate concentrations of As, Mo, and Se increase over time. Three kinetics equations, pseudo-second order, Elovich, and power-function, are able to adequately describe the experimental leaching kinetics data. Experimental leachingmore » data and modeling results indicate that the rate limiting leaching of As, Mo, and Se is largely controlled by the dissolution of the fly ash particles. Furthermore, it is important to adopt effective containment/treatment schemes to avoid potential and persistent dispersion of trace elements from ash disposal facilities to surrounding environment for a long time.« less

Utilization of coal fly ash as a slow-release granular medium for soil improvement.

PubMed

Yoo, Jeong Gun; Jo, Young Min

2003-01-01

This work proposes a new potential application of waste coal fly ash as a K fertilizer support. Fly ash was reacted with KOH to facilitate the impregnation of K as well as to enhance the bonding force. In particular, the applied process resulted in a significant slow-releasing characteristic of fertilizer elements. To examine the effect of K impregnation, a few detailed leaching tests were carried out in terms of process variables such as reaction time and temperature, sintering time and temperature, and KOH concentration. The current experiment presented an optimum preparation condition that is competitive with conventional commercial fertilizers. The manufactured ash fertilizers inhibited release of the K elements. It was also found through the continuous leaching test with pure water that the ash fertilizer had excellent moisture absorbability. However, the effects of some trace elements in fly ash on soil health and crop productivity as well as environmental considerations need to be established with long-term studies.

Implications of elastic wave velocities for Apollo 17 rock powders

NASA Technical Reports Server (NTRS)

Talwani, P.; Nur, A.; Kovach, R. L.

1974-01-01

Ultrasonic P- and S-wave velocities of lunar rock powders 172701, 172161, 170051, and 175081 were measured at room temperature and to 2.5 kb confining pressure. The results compare well with those of terrestrial volcanic ash and powdered basalt. P-wave velocity values up to pressures corresponding to a lunar depth of 1.4 km preclude cold compaction alone as an explanation for the observed seismic velocity structure at the Apollo 17 site. Application of small amounts of heat with simultaneous application of pressure causes rock powders to achieve equivalence of seismic velocities for competent rocks.

Clean up fly ash from coal burning plants by new isolated fungi Fusarium oxysporum and Penicillium glabrum.

PubMed

Ertit Taştan, Burcu

2017-09-15

In Turkey approximately 45 million tons of coals are burned in a year and 19.3 million tons of fly ash have emerged. The bioremediation of heavy metals or different elements from fly ash makes them bio-available. However, in previous studies, requiring of long operational time and failing to show tolerance to high pulp densities of fly ash of selected fungal species makes them impractical. In this work, bioremediation of fly ash by new isolated fungi Fusarium oxysporum and Penicillium glabrum were investigated in one step and two step bioremediation process. Ca, Si, Fe and S were found to be considerable amount in studied fly ashes by ED-XRF element analysis. The bioremediation yields of Mo (100%), S (64.36%) Ni (50%) and Cu (33.33%) by F. oxysporum were high. The remediated elements by P. glabrum in fly ash were Mo (100%), S (57.43%), Ni (25%), Si (24.66%), V (12.5%), Ti (5%) and Sr (3.2%). The isolation of high fly ash resistant fungi and reduction of the bioremediation time will allow the practical applications of the bioremediation technology when it is scaled up. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optimizing Use of Girdled Ash Trees for Management of Low-Density Emerald Ash Borer (Coleoptera: Buprestidae) Populations.

PubMed

Siegert, Nathan W; McCullough, Deborah G; Poland, Therese M; Heyd, Robert L

2017-06-01

Effective survey methods to detect and monitor recently established, low-density infestations of emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), remain a high priority because they provide land managers and property owners with time to implement tactics to slow emerald ash borer population growth and the progression of ash mortality. We evaluated options for using girdled ash (Fraxinus spp.) trees for emerald ash borer detection and management in a low-density infestation in a forested area with abundant green ash (F. pennsylvanica). Across replicated 4-ha plots, we compared detection efficiency of 4 versus 16 evenly distributed girdled ash trees and between clusters of 3 versus 12 girdled trees. We also examined within-tree larval distribution in 208 girdled and nongirdled trees and assessed adult emerald ash borer emergence from detection trees felled 11 mo after girdling and left on site. Overall, current-year larvae were present in 85-97% of girdled trees and 57-72% of nongirdled trees, and larval density was 2-5 times greater on girdled than nongirdled trees. Low-density emerald ash borer infestations were readily detected with four girdled trees per 4-ha, and 3-tree clusters were as effective as 12-tree clusters. Larval densities were greatest 0.5 ± 0.4 m below the base of the canopy in girdled trees and 1.3 ± 0.7 m above the canopy base in nongirdled trees. Relatively few adult emerald ash borer emerged from trees felled 11 mo after girdling and left on site through the following summer, suggesting removal or destruction of girdled ash trees may be unnecessary. This could potentially reduce survey costs, particularly in forested areas with poor accessibility. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by US Government employees and is in the public domain in the US.

Equilibrium, Kinetic, and Thermodynamic Studies on the Adsorption of Cadmium from Aqueous Solution by Modified Biomass Ash

PubMed Central

Zheng, Xuebo; Cui, Hongbiao; Zhu, Zhenqiu; Liang, Jiani

2017-01-01

Natural biomass ash of agricultural residuals was collected from a power plant and modified with hexagonal mesoporous silica and functionalized with 3-aminopropyltriethoxysilane. The physicochemical and morphological properties of the biomass ash were analyzed by ICP-OES, SEM, TEM-EDS, FTIR, and BET analysis. The adsorption behavior of the modified product for Cd2+ in aqueous solution was studied as a function of pH, initial metal concentration, equilibrium time, and temperature. Results showed that the specific surface area of the modified product was 9 times that of the natural biomass ash. The modified biomass ash exhibited high affinity for Cd2+ and its adsorption capacity increased sharply with increasing pH from 4.0 to 6.0. The maximum adsorption capacity was 23.95 mg/g in a pH 5 solution with an initial metal concentration of 50 mg/L and a contact time of 90 min. The adsorption of Cd2+ onto the modified biomass ash was well fitted to the Langmuir model and it followed pseudo-second-order kinetics. Thermodynamic analysis results showed that the adsorption of Cd2+ was spontaneous and endothermic in nature. The results suggest that the modified biomass ash is promising for use as an inexpensive and effective adsorbent for Cd2+ removal from aqueous solution. PMID:28348509

Clay Stabilization Using the Ash of Mount Sinabung in Terms of the Value of California Bearing Ratio (CBR)

NASA Astrophysics Data System (ADS)

Hastuty, I. P.; Roesyanto, R.; Napitupulu, S. M. A.

2018-02-01

Most areas in Indonesia consist of clay soils with high plasticity so that to meet technical requirements the soil needs improvement, which is known as soil stabilization.There are three ways of soil stabilization process, i.e. mechanical, physical and chemical. In this study, chemical stabilization was performed, that was by adding stabilizing agents to the soil. The stabilizing agent used was the ash of Mount Sinabung. Since 2010 until now, Sinabung Mountain is still experiencing eruption that produces a lot of volcanic ash and it inconveniences the environment. So, it is expected that this research will be able to optimize the utilization of Sinabung ash. The purpose of this study was to investigate the effect of the addition of Mount Sinabung ash to CBR (California Bearing Ratio) value, to determine the effect of the curing time of one day and fourteen days mixture on the CBR value, and to find the mixed content with effective curing time to produce the largest CBR value. Based on this study, the soil type CL (Clay - Low Plasticity) was obtained, based on the classification of USCS (Unified Soil Classification System) and categorized as A-6 (6) based on the classification of AASHTO (American Association of State Highway and Transportation officials) with the most effective mixed stabilizer material which was the variation of 10% Mount Sinabung ash with fourteen days of curing time. The CBR value resulted from the mixture of 10% Sinabung ash that was cured within fourteen days was 8.95%. By the increase of the content of the Sinabung ash, the CBR value always improved to the level of 10%, Sinabung ash then decreased and became constant at the mixture of higher volcanic ash mixture but remained above the CBR value of the original soil.

Method for increasing the rate of compressive strength gain in hardenable mixtures containing fly ash

DOEpatents

Liskowitz, J.W.; Wecharatana, M.; Jaturapitakkul, C.; Cerkanowicz, A.E.

1997-10-28

The present invention relates to concrete, mortar and other hardenable mixtures comprising cement and fly ash for use in construction. The invention provides a method for increasing the rate of strength gain of a hardenable mixture containing fly ash by exposing the fly ash to an aqueous slurry of calcium oxide (lime) prior to its incorporation into the hardenable mixture. The invention further relates to such hardenable mixtures, e.g., concrete and mortar, that contain fly ash pre-reacted with calcium oxide. In particular, the fly ash is added to a slurry of calcium oxide in water, prior to incorporating the fly ash in a hardenable mixture. The hardenable mixture may be concrete or mortar. In a specific embodiment, mortar containing fly ash treated by exposure to an aqueous lime slurry are prepared and tested for compressive strength at early time points. 2 figs.

Method for increasing the rate of compressive strength gain in hardenable mixtures containing fly ash

DOEpatents

Liskowitz, John W.; Wecharatana, Methi; Jaturapitakkul, Chai; Cerkanowicz, deceased, Anthony E.

1997-01-01

The present invention relates to concrete, mortar and other hardenable mixtures comprising cement and fly ash for use in construction. The invention provides a method for increasing the rate of strength gain of a hardenable mixture containing fly ash by exposing the fly ash to an aqueous slurry of calcium oxide (lime) prior to its incorporation into the hardenable mixture. The invention further relates to such hardenable mixtures, e.g., concrete and mortar, that contain fly ash pre-reacted with calcium oxide. In particular, the fly ash is added to a slurry of calcium oxide in water, prior to incorporating the fly ash in a hardenable mixture. The hardenable mixture may be concrete or mortar. In a specific embodiment, mortar containing fly ash treated by exposure to an aqueous lime slurry are prepared and tested for compressive strength at early time points.

Fluidized bed combustion of pelletized biomass and waste-derived fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chirone, R.; Scala, F.; Solimene, R.

2008-10-15

The fluidized bed combustion of three pelletized biogenic fuels (sewage sludge, wood, and straw) has been investigated with a combination of experimental techniques. The fuels have been characterized from the standpoints of patterns and rates of fuel devolatilization and char burnout, extent of attrition and fragmentation, and their relevance to the fuel particle size distribution and the amount and size distribution of primary ash particles. Results highlight differences and similarities among the three fuels tested. The fuels were all characterized by limited primary fragmentation and relatively long devolatilization times, as compared with the time scale of particle dispersion away frommore » the fuel feeding ports in practical FBC. Both features are favorable to effective lateral distribution of volatile matter across the combustor cross section. The three fuels exhibited distinctively different char conversion patterns. The high-ash pelletized sludge burned according to the shrinking core conversion pattern with negligible occurrence of secondary fragmentation. The low-ash pelletized wood burned according to the shrinking particle conversion pattern with extensive occurrence of secondary fragmentation. The medium-ash pelletized straw yielded char particles with a hollow structure, resembling big cenospheres, characterized by a coherent inorganic outer layer strong enough to prevent particle fragmentation. Inert bed particles were permanently attached to the hollow pellets as they were incorporated into ash melts. Carbon elutriation rates were very small for all the fuels tested. For pelletized sludge and straw, this was mostly due to the shielding effect of the coherent ash skeleton. For the wood pellet, carbon attrition was extensive, but was largely counterbalanced by effective afterburning due to the large intrinsic reactivity of attrited char fines. The impact of carbon attrition on combustion efficiency was negligible for all the fuels tested. The size distribution of primary ash particles liberated upon complete carbon burnoff largely reflected the combustion pattern of each fuel. Primary ash particles of size nearly equal to that of the parent fuel were generated upon complete burnoff of the pelletized sludge. Nonetheless, secondary attrition of primary ash from pelletized sludge is large, to the point where generation of fine ash would be extensive over the typical residence time of bed ash in fluidized bed combustors. Very few and relatively fine primary ash particles were released after complete burnoff of wood pellets. Primary ash particles remaining after complete burnoff of pelletized straw had sizes and shapes that were largely controlled by the occurrence of ash agglomeration phenomena. (author)« less

Fly ash in landfill top covers - a review.

PubMed

Brännvall, E; Kumpiene, J

2016-01-01

Increase of energy recovery from municipal solid waste by incineration results in the increased amounts of incineration residues, such as fly ash, that have to be taken care of. Material properties should define whether fly ash is a waste or a viable resource to be used for various applications. Here, two areas of potential fly ash application are reviewed: the use of fly ash in a landfill top cover either as a liner material or as a soil amendment in vegetation layer. Fly ashes from incineration of three types of fuel are considered: refuse derived fuel (RDF), municipal solid waste incineration (MSWI) and biofuel. Based on the observations, RDF and MSWI fly ash is considered as suitable materials to be used in a landfill top cover liner. Whereas MSWI and biofuel fly ashes based on element availability for plant studies, could be considered suitable for the vegetation layer of the top cover. Responsible application of MSWI ashes is, however, warranted in order to avoid element accumulation in soil and elevation of background values over time.

Ash bed level control system for a fixed-bed coal gasifier

DOEpatents

Fasching, George E.; Rotunda, John R.

1984-01-01

An ash level control system is provided which incorporates an ash level meter to automatically control the ash bed level of a coal gasifier at a selected level. The ash level signal from the ash level meter is updated during each cycle that a bed stirrer travels up and down through the extent of the ash bed level. The ash level signal is derived from temperature measurements made by thermocouples carried by the stirrer as it passes through the ash bed and into the fire zone immediately above the ash bed. The level signal is compared with selected threshold level signal to determine if the ash level is above or below the selected level once each stirrer cycle. A first counter is either incremented or decremented accordingly. The registered count of the first counter is preset in a down counter once each cycle and the preset count is counted down at a selected clock rate. A grate drive is activated to rotate a grate assembly supporting the ash bed for a period equal to the count down period to maintain the selected ash bed level. In order to avoid grate binding, the controller provides a short base operating duration time each stirrer cycle. If the ash bed level drops below a selected low level or exceeds a selected high level, means are provided to notify the operator.

Characterization of typical heavy metals in pyrolysis MSWI fly ash.

PubMed

Xu, Tengtun; Wang, Li'ao; Zeng, Yunmin; Zhao, Xue; Wang, Lei; Zhan, Xinyuan; Li, Tong; Yang, Lu

2018-06-07

Thermal treatment methods are used extensively in the process of municipal solid waste incineration fly ash. However, the characterization of heavy metals during this process should be understood more clearly in order to control secondary pollution. In this paper, the content, speciation and leaching toxicity of mercury (Hg), plumbum (Pb), cadmium (Cd) and zinc (Zn) in fly ash treated under different temperatures and time were firstly analysed as pre-tests. Later, pilot-scale pyrolysis equipment was used to explore the concentration and speciation changes in the heavy metals of fly ash. Finally, the phase constitution and microstructure changes in fly ash were compared before and after pyrolysis using X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. The results showed that (a) The appropriate processing temperature was between 400°C and 450°C, and the processing time should be 1 h. (b) The stability of heavy metals in fly ash increased after pyrolysis. (c) XRD and SEM results indicated that phase constitution changed a little, but the microstructure varied to a porous structure similar to that of a coral reef after pyrolysis. These results suggest that pyrolysis could be an effective method in controlling heavy metal pollution in fly ash.

Solid Catalyst Nanoparticles derived from Oil-Palm Empty Fruit Bunches (OP-EFB) as a Renewable Catalyst for Biodiesel Production

NASA Astrophysics Data System (ADS)

Husin, H.; Asnawi, T. M.; Firdaus, A.; Husaini, H.; Ibrahim, I.; Hasfita, F.

2018-05-01

Solid nanocatalyst derived from oil-palm empty fruit bunches (OP-EFB) fiber was successfully synthesized and its application for biodiesel production was investigated. The OPEFB was treated by burning, milling and heating methods to generate ashes in a nanoparticle size. The nanoparticle palm-bunch ash was characterized by scanning electron microscopy (SEM) and x-ray diffraction (XRD). The effects of the calcination temperature and catalyst amounts for transesterification reactions were investigated. XRD analysis of palm bunch ash exhibited that the highest composition of peaks characteristic were potassium oxide (K2O). SEM analysis showed that the nano palm bunch ash have a particle size ranging of 150-400 nm. The highest conversion of palm-oil to biodiesel reach to 97.90% was observed by using of palm bunch ash nanocatalyst which heated at 600°C, 3 h reaction time and 1% catalyst amount. Reusability of palm bunch ash catalysts was also examined. It was found that of its high active sites, reusable solid catalyst was obtained by just heating of palm bunch ash. It has a capability to reduce not only the amount of catalyst consumption but also reduce the reaction time of transesterification process.

Recovery of aluminum and other metal values from fly ash

DOEpatents

McDowell, William J.; Seeley, Forest G.

1981-01-01

The invention described herein relates to a method for improving the acid leachability of aluminum and other metal values found in fly ash which comprises sintering the fly ash, prior to acid leaching, with a calcium sulfate-containing composition at a temperature at which the calcium sulfate is retained in said composition during sintering and for a time sufficient to quantitatively convert the aluminum in said fly ash into an acid-leachable form.

Recovery of aluminum and other metal values from fly ash

DOEpatents

McDowell, W.J.; Seeley, F.G.

1979-11-01

The invention relates to a method for improving the acid leachability of aluminum and other metal values found in fly ash which comprises sintering the fly ash, prior to acid leaching, with a calcium sulfate-containing composition at a temperature at which the calcium sulfate is retained in said composition during sintering and for a time sufficient to quantitatively convert the aluminum in said fly ash into an acid-leachable form.

Permeation Properties and Pore Structure of Surface Layer of Fly Ash Concrete

PubMed Central

Liu, Jun; Qiu, Qiwen; Xing, Feng; Pan, Dong

2014-01-01

This paper presents an experimental study on the nature of permeation properties and pore structure of concrete surface layers containing fly ash. Concretes containing different dosages of fly ash as a replacement for cement (15% and 30% by weight of total cement materials, respectively) were investigated. Concrete without any fly ash added was also employed as the reference specimen. Laboratory tests were conducted to determine the surface layer properties of concrete including chloride transport, apparent water permeability and pore structure. The results demonstrate that incorporation of fly ash, for the early test period, promotes the chloride ingress at the surface layer of concrete but substituting proportions of fly ash may have little impact on it. With the process of chloride immersion, the chloride concentration at the surface layer of concrete with or without fly ash was found to be nearly the same. In addition, it is suggested that the water permeability at the concrete surface area is closely related to the fly ash contents as well as the chloride exposure time. Pore structure was characterized by means of mercury intrusion porosimetry (MIP) test and the scanning electron microscopy (SEM) images. The modification of pore structure of concrete submersed in distilled water is determined by the pozzolanic reaction of fly ash and the calcium leaching effect. The pozzolanic reaction was more dominant at the immersion time of 180 days while the calcium leaching effect became more evident after 270 days. PMID:28788677

Spatial distribution of volcanic ash deposits of 2011 Puyehue-Cordón Caulle eruption in Patagonia as measured by a perturbation in NDVI temporal dynamics

NASA Astrophysics Data System (ADS)

Easdale, M. H.; Bruzzone, O.

2018-03-01

Volcanic ash fallout is a recurrent environmental disturbance in forests, arid and semi-arid rangelands of Patagonia, South America. The ash deposits over large areas are responsible for several impacts on ecological processes, agricultural production and health of local communities. Public policy decision making needs monitoring information of the affected areas by ash fallout, in order to better orient social, economic and productive aids. The aim of this study was to analyze the spatial distribution of volcanic ash deposits from the eruption of Puyehue-Cordón Caulle in 2011, by identifying a sudden change in the Normalized Difference Vegetation Index (NDVI) temporal dynamics, defined as a perturbation located in the time series. We applied a sparse-wavelet transform using the Basis Pursuit algorithm to NDVI time series obtained from the Moderate Resolution Image Spectroradiometer (MODIS) sensor, to identify perturbations at a pixel level. The spatial distribution of the perturbation promoted by ash deposits in Patagonia was successfully identified and characterized by means of a perturbation in NDVI temporal dynamics. Results are encouraging for the future development of a new platform, in combination with data from forecasting models and tracking of ash cloud trajectories and dispersion, to inform stakeholders to mitigate impact of volcanic ash on agricultural production and to orient public intervention strategies after a volcanic eruption followed by ash fallout over a wide region.

Improving volcanic ash predictions with the HYSPLIT dispersion model by assimilating MODIS satellite retrievals

NASA Astrophysics Data System (ADS)

Chai, Tianfeng; Crawford, Alice; Stunder, Barbara; Pavolonis, Michael J.; Draxler, Roland; Stein, Ariel

2017-02-01

Currently, the National Oceanic and Atmospheric Administration (NOAA) National Weather Service (NWS) runs the HYSPLIT dispersion model with a unit mass release rate to predict the transport and dispersion of volcanic ash. The model predictions provide information for the Volcanic Ash Advisory Centers (VAAC) to issue advisories to meteorological watch offices, area control centers, flight information centers, and others. This research aims to provide quantitative forecasts of ash distributions generated by objectively and optimally estimating the volcanic ash source strengths, vertical distribution, and temporal variations using an observation-modeling inversion technique. In this top-down approach, a cost functional is defined to quantify the differences between the model predictions and the satellite measurements of column-integrated ash concentrations weighted by the model and observation uncertainties. Minimizing this cost functional by adjusting the sources provides the volcanic ash emission estimates. As an example, MODIS (Moderate Resolution Imaging Spectroradiometer) satellite retrievals of the 2008 Kasatochi volcanic ash clouds are used to test the HYSPLIT volcanic ash inverse system. Because the satellite retrievals include the ash cloud top height but not the bottom height, there are different model diagnostic choices for comparing the model results with the observed mass loadings. Three options are presented and tested. Although the emission estimates vary significantly with different options, the subsequent model predictions with the different release estimates all show decent skill when evaluated against the unassimilated satellite observations at later times. Among the three options, integrating over three model layers yields slightly better results than integrating from the surface up to the observed volcanic ash cloud top or using a single model layer. Inverse tests also show that including the ash-free region to constrain the model is not beneficial for the current case. In addition, extra constraints on the source terms can be given by explicitly enforcing no-ash for the atmosphere columns above or below the observed ash cloud top height. However, in this case such extra constraints are not helpful for the inverse modeling. It is also found that simultaneously assimilating observations at different times produces better hindcasts than only assimilating the most recent observations.

Optoelectronic system of online measurements of unburned carbon in coal fly ash

NASA Astrophysics Data System (ADS)

Golas, Janusz; Jankowski, Henryk; Niewczas, Bogdan; Piechna, Janusz; Skiba, Antoni; Szkutnik, Wojciech; Szkutnik, Zdzislaw P.; Wartak, Ryszarda; Worek, Cezary

2001-08-01

Carbon-in-ash level is an important consideration for combustion efficiency as well as ash marketing. The optoelectronic analyzing system for on-line determination and monitoring of the u burned carbon content of ash samples is presented. The apparatus operates on the principle that carbon content is proportional to the reflectance of IR light. Ash samples are collected iso kinetically from the flue gas duct and placed in a sample tube with a flat glass bottom. The same is then exposed to a light. The reflectance intensity is used by the system's computer to determine residual carbon content from correlation curves. The sample is then air purged back to the duct or to the attached sample canister to enable laboratory check analysis. The total cycle time takes between 5 and 10 minutes. Real time result of carbon content with accuracy 0.3-0.7 percent are reported and can be used for boiler controlling.

Experiment Investigation of the Influencing Factors on Bed Agglomeration During Fluidized-Bed Gasification of Biomass Fuels

NASA Astrophysics Data System (ADS)

Chen, Y. Q.; Chen, H. P.; Yang, H. P.; Wang, X. H.; Zhang, S. H.

With the depleting of fossil fuel and environmental polluting increasing, the utilization of biomass resources caught increasing concern. Biomass gasification in fluidized bed, as one promising technology, developed quickly. However, serious agglomeration was displayed as biomass ash reacted with bed material (silica sand) at higher temperature. It hindered the wide utilization of CFB gasifier. The objective ofthis work is to investigate the agglomeration behavior between biomass ash and silica sand, and catch the inherent mechanism. Firstly, the influence of ash compounds on the agglomeration behavior was analyzed with biomass ash and synthesis ash compounds addition in fixed bed as ash sample mixed with bed material evenly before every trial. The reaction temperature was set 850°C that is the operated temperature for many fluidized bed gasificated biomass fuels. Then the influence of reaction time was analyzed. The characteristics of the agglomerated silica sand particles were analyzed by the XRD. Finally, it was simulated with HSC computer mode based on thermodynamic equilibrium. It was observed that when the ratio of the biomass ash to the silica sand was above 0.2, the agglomeration was observed. With the increase of the reaction time, more silica sand particles agglomerated with the biomass ash. There are two kinds of silicate eutecticum investigated by the XRD. It is of great significance for the running ofCFB biomass gasifier and the development ofbiomass utilization technology.

Dynamics of volcanic ash remobilisation by wind through the Patagonian steppe after the eruption of Cordón Caulle, 2011

PubMed Central

Panebianco, Juan E.; Mendez, Mariano J.; Buschiazzo, Daniel E.; Bran, Donaldo; Gaitán, Juan J.

2017-01-01

Wind erosion of freshly-deposited volcanic ash causes persistent storms, strongly affecting ecosystems and human activity. Wind erosion of the volcanic ash was measured up to 17 months after the ash deposition, at 7 sites located within the ash-deposition area. The mass flux was measured up to 1.5 m above ground level. Mass transport rates were over 125 times the soil wind-erosion rates observed before the ash deposition, reaching up to 6.3 kg m−1 day−1. Total mass transport of ash during the 17 months ranged between 113.6 and 969.9 kg m−1 depending on topographic location and wind exposure. The vertical distribution of the mass flux at sites with higher vegetation cover was generally inverted as compared to sites with lower vegetation cover. This situation lasted 7 months and then a shift towards a more uniform vertical distribution was observed, in coincidence with the beginning of the decline of the mass transport rates. Decay rates differed between sites. Despite changes over time, an inverse linear correlation between the mass transports and the mass-flux gradients was found. Both the mass-flux gradients and the average mass-transport rates were not linked with shear-stress partition parameters, but with the ratio: ash-fall thickness to total vegetation cover. PMID:28349929

Dynamics of volcanic ash remobilisation by wind through the Patagonian steppe after the eruption of Cordón Caulle, 2011.

PubMed

Panebianco, Juan E; Mendez, Mariano J; Buschiazzo, Daniel E; Bran, Donaldo; Gaitán, Juan J

2017-03-28

Wind erosion of freshly-deposited volcanic ash causes persistent storms, strongly affecting ecosystems and human activity. Wind erosion of the volcanic ash was measured up to 17 months after the ash deposition, at 7 sites located within the ash-deposition area. The mass flux was measured up to 1.5 m above ground level. Mass transport rates were over 125 times the soil wind-erosion rates observed before the ash deposition, reaching up to 6.3 kg m -1 day -1 . Total mass transport of ash during the 17 months ranged between 113.6 and 969.9 kg m -1 depending on topographic location and wind exposure. The vertical distribution of the mass flux at sites with higher vegetation cover was generally inverted as compared to sites with lower vegetation cover. This situation lasted 7 months and then a shift towards a more uniform vertical distribution was observed, in coincidence with the beginning of the decline of the mass transport rates. Decay rates differed between sites. Despite changes over time, an inverse linear correlation between the mass transports and the mass-flux gradients was found. Both the mass-flux gradients and the average mass-transport rates were not linked with shear-stress partition parameters, but with the ratio: ash-fall thickness to total vegetation cover.

Comparison of leaching characteristics of heavy metals from bottom and fly ashes in Korea and Japan.

PubMed

Shim, Young-Sook; Rhee, Seung-Whee; Lee, Woo-Keun

2005-01-01

The objective of this research was to compare the leaching characteristics of heavy metals such as cadmium, chromium, copper, nickel, lead, etc., in Korean and Japanese municipal solid waste incineration (MSWI) ash. The rate of leaching of heavy metal was measured by KSLT and JTL-13, and the amount of heavy metals leached was compared with the metal content in each waste component. Finally, bio-availability testing was performed to assess the risks associated with heavy metals leached from bottom ash and fly ash. From the results, the value of neutralization ability in Japanese fly ash was four times higher than that in Korean fly ash. The reason was the difference in the content of Ca(OH)(2) in fly ash. The amount of lead leached exceeded the regulatory level in both Japanese and Korean fly ash. The rate of leaching was relatively low in ash with a pH in the range of 6-10. The bio-availability test in fly ash demonstrated that the amount of heavy metals leached was Pb>Cd>Cr, but the order was changed to Pb>Cr>Cd in the bottom ash. The leaching concentration of lead exceeded the Japanese risk level in all fly ashes from the two countries, but the leaching concentration of cadmium exceeded the regulatory level in Korean fly ash only.

Ash level meter for a fixed-bed coal gasifier

DOEpatents

Fasching, George E.

1984-01-01

An ash level meter for a fixed-bed coal gasifier is provided which utilizes the known ash level temperature profile to monitor the ash bed level. A bed stirrer which travels up and down through the extent of the bed ash level is modified by installing thermocouples to measure the bed temperature as the stirrer travels through the stirring cycle. The temperature measurement signals are transmitted to an electronic signal process system by an FM/FM telemetry system. The processing system uses the temperature signals together with an analog stirrer position signal, taken from a position transducer disposed to measure the stirrer position to compute the vertical location of the ash zone upper boundary. The circuit determines the fraction of each total stirrer cycle time the stirrer-derived bed temperature is below a selected set point, multiplies this fraction by the average stirrer signal level, multiplies this result by an appropriate constant and adds another constant such that a 1 to 5 volt signal from the processor corresponds to a 0 to 30 inch span of the ash upper boundary level. Three individual counters in the processor store clock counts that are representative of: (1) the time the stirrer temperature is below the set point (500.degree. F.), (2) the time duration of the corresponding stirrer travel cycle, and (3) the corresponding average stirrer vertical position. The inputs to all three counters are disconnected during any period that the stirrer is stopped, eliminating corruption of the measurement by stirrer stoppage.

Sinabung Volcanic Ash Utilization As The Additive for Paving Block Quality A and B

NASA Astrophysics Data System (ADS)

Sembiring, I. S.; Hastuty, I. P.

2017-03-01

Paving block is one of the building materials used as the top layer of the road structure besides asphalt and concrete. Paving block is made of mixed materials such as portland cement or other adhesive materials, water and aggregate. In this research, the material used as the additive of cement and concrete is volcanic ash from Mount Sinabung, it is based on the results of the material testing, Sinabung ash contains 74.3% silica (SiO2). The purpose of this research aims to analyze the behavior of the paving blocks quality A and B with and without a mixture of Sinabung ash, to analyze the workability of fresh concrete using Sinabung ash as an additive in concrete, and to compare the test results of paving blocks with and without using Sinabung ash. The samples that we made consist of four variations of the concrete mix to experiment a mixture of normal sample without additive, samples which are mixed with the addition of Sinabung ash 5%, 10%, 15%, 20% and 25% of the volume of concrete/m3. Each variation consists of 10 samples of the concrete with 28 days curing time period. We will do the compressive strength and water absorption test to the samples to determine whether the samples are in accordance with the type needed. According to the test result, paving blocks with Sinabung ash and curing time reach quality A at 0%, 5% and 10% mixture with the compressive strength of each 50.14 MPa, 46.20 MPa and 1.49Mpa, and reach quality B at 15%, 20 %,25% mixture with curing time and 0%, 5%, 10%, 15%, 20% and 25% mixture without curing time. According to the absorption values we got from the test which are 6.66%, 6.73%, 6.88%, 7.03%, 7.09% and 7.16%, the entire sample have average absorption exceeding SNI standardization which is above 6% and reach quality C. Based on compressive strength and absorption data obtained Sinabung ash can’t fully replace cement as the binder because of the low CaO content.

[Pretreatment technology for fly ash from MSWI and the corresponding study of chloride behavior].

PubMed

Zhu, Fen-Fen; Takaoka, Masaki; Oshita, Kazuyuki; Jiang, Hui-Min; Kitajima, Yoshinori

2013-06-01

The introduced pretreatment technology, WCCB (Washing + Calcination), was effective to reduce chlorides in fly ash by consuming relatively low energy for recycling fly ash as the raw material for cement industry. The washing conditions are: twice-washing, liquid/solid = 3, mixing speed = 150 r x min(-1), 1st mixing time = 5 min, and 2nd mixing time = 10 min. The original incinerator was used for the calcination process, 1 000 degrees C, 10% O2 and dwelling time of 1 hour were adopted. By adopting X-ray absorption near edge structure and X-ray diffraction, the behavior of chlorides was explained and NaCl, KCl and CaCl2 are the main form of chlorides existing in fly ash. The reagent used in the air pollution control system to neutralize the acid component in the discharged gas surely acted a very important role in the formation of chlorides. The insoluble chlorides in fly ash had a very similar structure as that of Friedel's salt, which was related with CaCl2.

Quantifying distal dispersal and impact of volcanic ash from super-eruptions: an application to Campanian Ignimbrite

NASA Astrophysics Data System (ADS)

Costa, A.; Folch, A.; Macedonio, G.; Giaccio, B.; Isaia, R.; Smith, V. C.

2012-04-01

Distal and ultra-distal volcanic ash dispersal during a super-eruption was reconstructed for the first time, providing insights into eruption dynamics and the impact of these gigantic events. A novel computational methodology was applied to the ash fallout of the Campanian Ignimbrite (CI), the most powerful volcanic eruption in Europe in the last 200 kyrs. The method uses a 3D time-dependent computational ash dispersion model, an ensemble of wind fields, and hundreds of thickness observations of the CI tephra deposit. Results reveal that 250-300 km3 of fallout material was produced during the eruption, blanketing a region of ~3.7 million km2 with more than 5 mm of fine ash. The model also indicates that the column height was ~37-40 km, and the eruption lasted 2-4 days. The eruption would have caused a volcanic winter within the coldest and driest Heinrich event. Fluorine-bearing leachate from the volcanic ash and acid rain would have further affected food sources and severely impacted Late Middle Paleolithic groups in Southern and Eastern Europe.

The partitioning of heavy metals in incineration of sludges and waste in a bubbling fluidized bed 2. Interpretation of results with a conceptual model.

PubMed

Toledo, José M; Corella, José; Corella, Luis M

2005-11-11

This work addresses the behavior, fate and/or partitioning of six targeted (Cd, Pb, Cr, Cu, Zn and Ni) heavy metals (HMs) in the incineration of sludges and waste in a bubbling fluidized bed (BFB) of 15 cm i.d. and 5.2m high followed by a filter chamber operated at 750-760 degrees C with a commercial ceramic filter. This paper presents three different things: (1) an in depth review of the published work relating to the problem of partitioning of the HMs in BFBs, (2) some more experimental incineration tests regarding the influence of the temperature of the bed of the BFB and the effect of the chlorine content in the feedstock on the partitioning of the HMs, and (3) the modelling of the partitioning of the HMs in the exit flows: bottom ash, coarse fly ashes, fine fly ash and vapour phase. The partitioning of the HMs is governed by fluid dynamic principles together with the kinetics of the diffusion of the HMs inside the ash particles and the kinetics of the reactions between the HMs and the components of the matrix of the ash. Some thermodynamic predictions do not fit the results from the BFB incinerator well enough because equilibria are not reached in at least three exit ash flows: coarse fly ash, fine fly ash and submicron particles. The residence time of these ash particles in these type of incinerators is very short and most of the HMs have no time to diffuse out of the ash particle. Finally, an examination was made on how in the ceramic hot filter the partition coefficients for the HMs increased, mainly for Cd and Pb, when the Cl-content in the feedstock was increased.

Analysis of Physical Properties and Mineralogical of Pyrolysis Tires Rubber Ash Compared Natural Sand in Concrete material

NASA Astrophysics Data System (ADS)

Syamir Senin, Mohamad; Shahidan, Shahiron; Syazani Leman, Alif; Izzati Raihan Ramzi Hannan, Nurul

2016-11-01

Waste tires pose significant health and environmental concerns if not recycled or discarded properly. At the same time, natural sand is becoming scarcer and costlier due to its non-availability. Waste tires as fine aggregate can be an economical and sustainable alternative to the natural sand. Recent years, the interest on recycling waste tires into civil engineering applications by the researchers has increased. In this research, the chemical and physical properties of the tires rubber ash and the natural sand have been analysed. The densities of the rubber ash are lower than the natural sand. Rubber ash had finer particle size compared to the natural sand. Almost all chemical in the natural sand had in rubber ash with the additional sulphur trioxide and zinc oxide in the rubber ash, made the rubber ash better than natural sand. Rubber ash seems to be a suitable material to use in concrete as sand replacement.

Multi-year residual activity of Arborjet's IMA-jet (imidacloprid 5% SL) against emerald ash borer [Agrilus planipennis Fairemaire (Coleoptera: Buprestidae)] in green ash (Fraxinus pennsylvanica Marsh) in Troy, MI.

Treesearch

Joseph J. Doccola; Peter M. Wild; Eric J. Bristol; Joseph Lojko; Xin Li

2007-01-01

In cooperative university studies, IMA-jet treated green ash were effectively protected for 2 years to date in Troy, MI against emerald ash borer (EAB). Trees were infested at the time of treatment, exhibiting epicormic sprouting and thinning canopies. Twenty trees were injected with IMA-jet alone or with a diluent to aid uptake and translocation within the vascular...

Emerald ash borer (Agrilus planipennis): Towards a classification of tree health and early detection

Treesearch

Matthew P. Peters; Louis R. Iverson; T. Davis Sydnor

2009-01-01

Forty-five green ash (Fraxinus pennsylvanica) street trees in Toledo, Ohio were photographed, measured, and visually rated for conditions related to emerald ash borer (Agrilus planipennis) (EAB) attacks. These trees were later removed, and sections were examined from each tree to determine the length of time that growth rates had...

Biology and life history of Tetrastichus planipennisi (Hymenoptera: Eulophidae) a larval endoparasitoid of the emerald ash borer (Coleoptera:Buprestidae)

Treesearch

Jian J. Duan; Craig B. Oppel; Michael D. Ulyshen; Leah S. Bauer; Jonathan LeLito

2011-01-01

Tetrastichus planipennisi (Hymenoptera: Eulophidae) is a gregarious larval endoparasitoid from China that is being released in the United States as a biocontrol agent of the emerald ash borer (Agrilus planipennis Fairmaire), an exotic beetle responsible for widespread ash mortality. The developmental time of immature stages, adult...

Grimsvotn ash plume detection by ground-based elastic Lidar at Dublin Airport on May 2011

NASA Astrophysics Data System (ADS)

Lolli, S.; Martucci, G.; O'Dowd, C.; sauvage, L.; Nolan, P.

2011-12-01

Volcanic emissions comprising steam, ash, and gases are injected into the atmosphere and produce effects affecting Earth's climate. Volcanic ash is composed of non-spherical mineral and metal (particles spanning a large size range. The largest ones are likely to sediment quickly close to the eruption site. The ash component, and sulphate formed by subsequent oxidation of the SO2 occurring in clouds, poses a variety of hazards to humans and machinery on the ground, as well as damage to the aircrafts which fly through the ash layers. To mitigate such hazards the Irish Aviation Authority (IAA) equipped with an ALS Lidar, produced by LEOSPHERE, deployed at Dublin Airport, which provides real-time range-corrected backscatter signal and depolarization ratio profiles allowing the detection and monitoring of ash plumes. On May, 21st 2011, the Grimsvotn Icelandic volcano erupted, sending a plume of ash, smoke and steam 12 km into the air and causing flights to be disrupted at Iceland's main Keflavik airport and at a number of North European airports. Due to upper level global circulation, the ash plume moved from Iceland towards Ireland and North of Scotland, and was detected a number of times by the ALS Lidar above Dublin Airport between May, 21st and 25th. A preliminary analysis of the detected volcanic plume is presented here as well as a preliminary intercomparison of the microphysical and optical characteristics with the Eyjafjallajökull eruption in 2010.

Restoration of fly ash dump through biological interventions.

PubMed

Juwarkar, Asha A; Jambhulkar, Hemlata P

2008-04-01

Field experiment on 10 ha area of fly ash dump was conducted to restore and revegetate it using biological interventions, which involves use of organic amendment, selection of suitable plant species along with specialized nitrogen fixing strains of biofertilizer. The results of the study indicated that amendment with farm yard manure at 50 t/ha improved the physical properties of fly ash such as maximum water holding capacity from 40.0 to 62.42% while porosity improved from 56.78 to 58.45%. The nitrogen content was increased by 4.5 times due to addition of nitrogen fixing strains of Bradyrhizobium and Azotobacter species, while phosphate content was increased by 10.0 times due to addition of VAM, which helps in phosphate immobilization. Due to biofertilizer inoculation different microbial groups such as Rhizobium, Azotobacter and VAM spores, which were practically absent in fly ash improved to 7.1 x 10(7), 9.2 x 10(7) CFU/g and 35 VAM spores/10 g of fly ash, respectively. Inoculation of biofertilizer and application of FYM helped in reducing the toxicity of heavy metals such as cadmium, copper, nickel and lead which were reduced by 25, 46, 48 and 47%, respectively, due to the increased organic matter content in the fly ash which complexes the heavy metals thereby decreasing the toxicity of metals. Amendment of fly ash with FYM and biofertilizer helped in profuse root development showing 15 times higher growth in Dendrocalamus strictus plant as compared to the control. Thus amendment and biofertilizer application provided better supportive material for anchorage and growth of the plant.

The effect of water binder ratio and fly ash on the properties of foamed concrete

NASA Astrophysics Data System (ADS)

Saloma, Hanafiah, Urmila, Dea

2017-11-01

Foamed concrete is a lightweight concrete composed by cement, water, fine aggregate and evenly distributed foam. Foamed concrete is produced by adding foam to the mixture. The function of foam is to create air voids in the mixture, so the weight of the concrete becomes lighter. The foaming agent is diluted in water then given air pressure by foam generator to produce foam. This research utilizes coal combustion, which is fly ash as cementitious material with a percentage of 0%, 10%, 15%, and 20%. The purpose of the research is to examine the effect of water binder ratio 0.425, 0.450, 0.475, and 0.500 using fly ash on the properties of foamed concrete. Fresh concrete tests include slump flow and setting time test while hardened concrete tests include density and compressive strength. The maximum value of slump flow test result is 59.50 cm on FC-20-0.500 mixture with w/b = 0.500 and 20% of fly ash percentage. The results of the setting time tests indicate the fastest initial and final time are 335 and 720 minutes, respectively on FC-0-0.425 mixture with w/b = 0.425 without fly ash. The lowest density is 978.344 kg/m3 on FC-20-0.500 mixture with w/b = 0.500 and 20% of fly ash percentage. The maximum compressive strength value is 4.510 MPa at 28 days on FC-10-0.450 mixture with w/b = 0.450 and 10% of fly ash percentage.

Larval Survival and Growth of Emerald Ash Borer (Coleoptera: Buprestidae) on White Ash and White Fringetree Saplings Under Well-Watered and Water-Deficit Conditions.

PubMed

Rutledge, Claire E; Arango-Velez, Adriana

2017-04-01

Emerald ash borer (Agrilus planipennis Fairmaire) was recently found on a novel host in North America, white fringetree (Chionanthus virginicus L.) (Oleaceae). In this study, we artificially infested 4-yr-old, naïve white fringetree and white ash (Fraxinus americana L.) saplings under well-watered and water-deficit conditions with emerald ash borer eggs. We used physiological and phenotypical approaches to investigate both plant response to emerald ash borer and insect development at 21, 36, and 61 d postinfestation. Photosynthesis was reduced in both tree species by larval feeding, but not by water deficits. Emerald ash borer larvae established and survived successfully on white ash. Both establishment and survival were lower on white fringetree than on white ash. Larvae were larger, and had reached higher instars at all three time points on white ash than on white fringetrees. Larvae grew faster in white ash under water-deficit conditions; however, water-deficit conditions negatively impacted survival of larvae at 61 d postinfestation in white fringetrees, although head size did not differ among surviving larvae. White ash showed higher callus formation in well-watered trees, but no impact on larval survival was observed. In white fringetree, callus formation was not affected by water treatment, and was inversely related to larval survival. The higher rate of mortality and slow growth rate of larvae in white fringetree as compared to white ash suggest that populations of emerald ash borer may be sustained by white fringetree, but may grow more slowly than in white ash. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Volcanic Ash and SO2 Monitoring Using Suomi NPP Direct Broadcast OMPS Data

NASA Astrophysics Data System (ADS)

Seftor, C. J.; Krotkov, N. A.; McPeters, R. D.; Li, J. Y.; Brentzel, K. W.; Habib, S.; Hassinen, S.; Heinrichs, T. A.; Schneider, D. J.

2014-12-01

NASA's Suomi NPP Ozone Science Team, in conjunction with Goddard Space Flight Center's (GSFC's) Direct Readout Laboratory, developed the capability of processing, in real-time, direct readout (DR) data from the Ozone Mapping and Profiler Suite (OMPS) to perform SO2 and Aerosol Index (AI) retrievals. The ability to retrieve this information from real-time processing of DR data was originally developed for the Ozone Monitoring Instrument (OMI) onboard the Aura spacecraft and is used by Volcano Observatories and Volcanic Ash Advisory Centers (VAACs) charged with mapping ash clouds from volcanic eruptions and providing predictions/forecasts about where the ash will go. The resulting real-time SO2 and AI products help to mitigate the effects of eruptions such as the ones from Eyjafjallajokull in Iceland and Puyehue-Cordón Caulle in Chile, which cause massive disruptions to airline flight routes for weeks as airlines struggle to avoid ash clouds that could cause engine failure, deeply pitted windshields impossible to see through, and other catastrophic events. We will discuss the implementation of real-time processing of OMPS DR data by both the Geographic Information Network of Alaska (GINA) and the Finnish Meteorological Institute (FMI), which provide real-time coverage over some of the most congested airspace and over many of the most active volcanoes in the world, and show examples of OMPS DR processing results from recent volcanic eruptions.

Optimal boiler control through real-time monitoring of unburned carbon in fly ash by laser-induced breakdown spectroscopy.

PubMed

Kurihara, Miki; Ikeda, Koji; Izawa, Yoshinori; Deguchi, Yoshihiro; Tarui, Hitoshi

2003-10-20

A laser-induced breakdown spectroscopy (LIBS) technique has been applied for detection of unburned carbon in fly ash, and an automated LIBS unit has been developed and applied in a 1000-MW pulverized-coal-fired power plant for real-time measurement, specifically of unburned carbon in fly ash. Good agreement was found between measurement results from the LIBS method and those from the conventional method (Japanese Industrial Standard 8815), with a standard deviation of 0.27%. This result confirms that the measurement of unburned carbon in fly ash by use of LIBS is sufficiently accurate for boiler control. Measurements taken by this apparatus were also integrated into a boiler-control system with the objective of achieving optimal and stable combustion. By control of the rotating speed of a mill rotary separator relative to measured unburned-carbon content, it has been demonstrated that boiler control is possible in an optimized manner by use of the value of the unburned-carbon content of fly ash.

Preparation of poly-o-phenylenediamine/TiO 2/fly-ash cenospheres and its photo-degradation property on antibiotics

NASA Astrophysics Data System (ADS)

Huo, Pengwei; Yan, Yongsheng; Li, Songtian; Li, Huaming; Huang, Weihong

2010-03-01

A series of poly-o-phenylenediamine/TiO 2/fly-ash cenospheres(POPD/TiO 2/fly-ash cenospheres) composites have been prepared from o-phenylenediamine and TiO 2/fly-ash cenospheres under various polymerization conditions. The properties of the samples were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), specific surface area (BET), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) and UV-vis diffuse reflectance spectrum (UV-vis DRS). Photocatalytic activity was studied by degradation of antibiotics waste water under visible light. The results indicate that the photo-induced method is viable for preparing modified photocatalysts, and the modified photocatalysts have good absorption in visible light range. The photocatalysts of POPD/TiO 2/fly-ash cenospheres which have good performance are prepared at pH 3 and 4, and the polymerized time around 40 min. When the photocatalysts are prepared under the conditions of pH 3 and polymerized time 40 min, the degradation rate of roxithromycin waste water could reach near 60%, and it indicates that the way of POPD modified TiO 2/fly-ash cenospheres to degrade the antibiotics waste water is viable.

Biomass ash reutilisation as an additive in the composting process of organic fraction of municipal solid waste.

PubMed

Asquer, Carla; Cappai, Giovanna; De Gioannis, Giorgia; Muntoni, Aldo; Piredda, Martina; Spiga, Daniela

2017-11-01

In this work the effects of selected types of biomass ash on the composting process and final product quality were studied by conducting a 96-day long experiment where the source separated organic fraction of municipal waste, mixed with wood prunings that served as bulking agent, was added with 0%, 2%, 4% and 8% wt/wt of biomass ash. The evolution over time of the main process parameters was observed, and the final composts were characterised. On the basis of the results, both the composting process and the quality of the final product were improved by ash addition. Enhanced volatile solids reduction and biological stability (up to 32% and 52%, respectively, as compared to the unamended product) were attained when ash was added, since ash favored the aerobic degradation by acting asa physical conditioner. In the final products, higher humification of organic matter (expressed in terms of the humification index, that was 2.25 times higher in the most-enriched compost than in the unamended one) and total Ca, K, Mg and P content were observed when ash was used. The latter aspect may influence the composts marketability positively, particularly with regards to potassium and phosphorus. The heavy metals content, that is regarded as the main environmental disadvantage when using ash asa composting additive, did not negatively affect the final composts quality. However, some other controversial effects of ash, related to the moisture and temperature values attained during the process, pH (8.8-9.2 as compared to 8.2 of the unamended compost) and electrical conductivity levels (up to 53% higher as compared to the unamended compost) in the final composts, were also observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Phenologically informed re-ordering of Landsat to account for inter-annual variability: a method to map Ash trees (Fraxinus spp.) using remotely sensed imagery

NASA Astrophysics Data System (ADS)

Isaacson, B. N.; Singh, A.; Serbin, S. P.; Townsend, P. A.

2009-12-01

Rapid ecosystem invasion by the emerald ash borer (Agrilus planipennis Fairemaire) is forcing resource managers to make decisions regarding how best to manage the pest, but a detailed map of abundance of the host, ash trees of the genus Fraxinus, does not exist, frustrating fully informed management decisions. We have developed methods to map ash tree abundance across a broad spatial extent in Wisconsin using their unique phenology (late leaf-out, early leaf-fall) and the rich dataset of Landsat imagery that can be used to characterize ash senescence with respect to other deciduous species. However, across environmental gradients in Wisconsin, senescence can vary by days or even weeks such that leaf-drop within one species can temporally vary even within a single Landsat footprint. To address this issue, we used phenology products from NASA’s MODIS for North American Carbon Program (NACP) coupled with vegetation indices derived from a time series of Landsat imagery across multiple years to determine the phenological position of each Landsat pixel within a single idealized growing season. Pixels within Landsat images collected in different years were re-arranged in a phenologically-informed time series that described autumn senescence. This characterization of leaf-drop was then related to the abundance of ash trees, producing a spatially-generalizable model of moderate resolution capable of predicting ash abundance across the state using multiple Landsat scenes. Empirical models predicting ash abundance for two Landsat footprints in Wisconsin indicate model fits for ash abundance of R^2=0.65 in north-central WI, and R^2>0.70 in southeastern WI.

Intra- and inter-unit variation in fly ash petrography and mercury adsorption: Examples from a western Kentucky power station

USGS Publications Warehouse

Hower, J.C.; Finkelman, R.B.; Rathbone, R.F.; Goodman, J.

2000-01-01

Fly ash was collected from eight mechanical and 10 baghouse hoppers at each of the twin 150-MW wall-fired units in a western Kentucky power station. The fuel burned at that time was a blend of many low-sulfur, high-volatile bituminous Central Appalachian coals. The baghouse ash showed less variation between units than the mechanical hoppers. The mechanical fly ash, coarser than the baghouse ash, showed significant differences in the amount of total carbon and in the ratio of isotropic coke to both total carbon and total coke - the latter excluding inertinite and other unburned, uncoked coal. There was no significant variation in proportions of inorganic fly ash constituents. The inter-unit differences in the amount and forms of mechanical fly ash carbon appear to be related to differences in pulverizer efficiency, leading to greater amounts of coarse coal, therefore unburned carbon, in one of the units. Mercury capture is a function of both the total carbon content and the gas temperature at the point of fly ash separation, mercury content increasing with an increase in carbon for a specific collection system. Mercury adsorption on fly ash carbon increases at lower flue-gas temperatures. Baghouse fly ash, collected at a lower temperature than the higher-carbon mechanically separated fly ash, contains a significantly greater amount of Hg.

Salt-soda sinter process for recovering aluminum from fly ash

DOEpatents

McDowell, William J.; Seeley, Forest G.

1981-01-01

A method for recovering aluminum values from fly ash comprises sintering the fly ash with a mixture of NaCl and Na.sub.2 CO.sub.3 to a temperature in the range 700.degree.-900.degree. C. for a period of time sufficient to convert greater than 90% of the aluminum content of the fly ash into an acid-soluble fraction and then contacting the thus-treated fraction with an aqueous solution of nitric or sulfuric acid to effect dissolution of aluminum and other metal values in said solution.

Salt-soda sinter process for recovering aluminum from fly ash

DOEpatents

McDowell, W.J.; Seeley, F.G.

A method for recovering aluminum values from fly ash comprises sintering the fly ash with a mixture of NaCl and Na/sub 2/CO/sub 3/ to a temperature in the range 700/sup 0/ to 900/sup 0/C for a period of time sufficient to convert greater than 90% of the aluminum content of the fly ash into an acidsoluble fraction and then contacting the thus-treated fraction with an aqueous solution of nitric or sulfuric acid to effect dissolution of aluminum and other metal values in said solution.

Regional-scale input of dispersed and discrete volcanic ash to the Izu-Bonin and Mariana subduction zones

NASA Astrophysics Data System (ADS)

Scudder, Rachel P.; Murray, Richard W.; Schindlbeck, Julie C.; Kutterolf, Steffen; Hauff, Folkmar; McKinley, Claire C.

2014-11-01

We have geochemically and statistically characterized bulk marine sediment and ash layers at Ocean Drilling Program Site 1149 (Izu-Bonin Arc) and Deep Sea Drilling Project Site 52 (Mariana Arc), and have quantified that multiple dispersed ash sources collectively comprise ˜30-35% of the hemipelagic sediment mass entering the Izu-Bonin-Mariana subduction system. Multivariate statistical analyses indicate that the bulk sediment at Site 1149 is a mixture of Chinese Loess, a second compositionally distinct eolian source, a dispersed mafic ash, and a dispersed felsic ash. We interpret the source of these ashes as, respectively, being basalt from the Izu-Bonin Front Arc (IBFA) and rhyolite from the Honshu Arc. Sr-, Nd-, and Pb isotopic analyses of the bulk sediment are consistent with the chemical/statistical-based interpretations. Comparison of the mass accumulation rate of the dispersed ash component to discrete ash layer parameters (thickness, sedimentation rate, and number of layers) suggests that eruption frequency, rather than eruption size, drives the dispersed ash record. At Site 52, the geochemistry and statistical modeling indicates that Chinese Loess, IBFA, dispersed BNN (boninite from Izu-Bonin), and a dispersed felsic ash of unknown origin are the sources. At Site 1149, the ash layers and the dispersed ash are compositionally coupled, whereas at Site 52 they are decoupled in that there are no boninite layers, yet boninite is dispersed within the sediment. Changes in the volcanic and eolian inputs through time indicate strong arc-related and climate-related controls.

Volcanic eruptions, hazardous ash clouds and visualization tools for accessing real-time infrared remote sensing data

NASA Astrophysics Data System (ADS)

Webley, P.; Dehn, J.; Dean, K. G.; Macfarlane, S.

2010-12-01

Volcanic eruptions are a global hazard, affecting local infrastructure, impacting airports and hindering the aviation community, as seen in Europe during Spring 2010 from the Eyjafjallajokull eruption in Iceland. Here, we show how remote sensing data is used through web-based interfaces for monitoring volcanic activity, both ground based thermal signals and airborne ash clouds. These ‘web tools’, http://avo.images.alaska.edu/, provide timely availability of polar orbiting and geostationary data from US National Aeronautics and Space Administration, National Oceanic and Atmosphere Administration and Japanese Meteorological Agency satellites for the North Pacific (NOPAC) region. This data is used operationally by the Alaska Volcano Observatory (AVO) for monitoring volcanic activity, especially at remote volcanoes and generates ‘alarms’ of any detected volcanic activity and ash clouds. The webtools allow the remote sensing team of AVO to easily perform their twice daily monitoring shifts. The web tools also assist the National Weather Service, Alaska and Kamchatkan Volcanic Emergency Response Team, Russia in their operational duties. Users are able to detect ash clouds, measure the distance from the source, area and signal strength. Within the web tools, there are 40 x 40 km datasets centered on each volcano and a searchable database of all acquired data from 1993 until present with the ability to produce time series data per volcano. Additionally, a data center illustrates the acquired data across the NOPAC within the last 48 hours, http://avo.images.alaska.edu/tools/datacenter/. We will illustrate new visualization tools allowing users to display the satellite imagery within Google Earth/Maps, and ArcGIS Explorer both as static maps and time-animated imagery. We will show these tools in real-time as well as examples of past large volcanic eruptions. In the future, we will develop the tools to produce real-time ash retrievals, run volcanic ash dispersion models from detected ash clouds and develop the browser interfaces to display other remote sensing datasets, such as volcanic sulfur dioxide detection.

Construction procedures using self hardening fly ash

NASA Astrophysics Data System (ADS)

Thornton, S. I.; Parker, D. G.

1980-07-01

Fly ash produced in Arkansas from burning Wyoming low sulfur coal is self-hardening and can be effective as a soil stabilizing agent for clays and sands. The strength of soil-self hardening fly ash develops rapidly when compacted immediately after mixing. Seven day unconfined compressive strengths up to 1800 psi were obtained from 20% fly ash and 80% sand mixtures. A time delay between mixing the fly ash with the soil and compaction of the mixture reduced the strength. With two hours delay, over a third of the strength was lost and with four hours delay, the loss was over half. Gypsum and some commercial concrete retarders were effective in reducing the detrimental effect of delayed compaction. Adequate mixing of the soil and fly ash and rapid compaction of the mixtures were found to be important parameters in field construction of stabilized bases.

The influence of sugarcane bagasse ash as fly ash on cement quality

NASA Astrophysics Data System (ADS)

Rauf, N.; Damayanti, M. C.; Pratama, S. W. I.

2017-01-01

Fly ash often is used as the third material for cement. The fly ash from sugarcane bagasse is usually considered as industrial waste material that can be added to the base material of cement (clinker, trash, gypsum and lime stone) for economic and environment reason. The amount of fly ash usually up to 30 % of cement material, but in this research the percentage of sugarcane bagasse ash (SBA) is added to cement material is up to 15% total weight. Then the x-rays fluorescence (XRF) was used to determine its chemical composition of raw material and cement samples. The physical properties of cement such as fineness, setting time, expansion, and compressive strength were measured using Automatic Blaine, Vicat, Autoclave, respectively. The result show that the percentage of sugarcane bagasse ash influences the quality of cement and concrete, and this is confirmed with Indonesia National Standard (SNI). It is showed that the sugarcane bagasse ash could be use as material to improve the quality of cement and will solve the environment waste material

Observed practices and perceived advantages of different hand cleansing agents in rural Bangladesh: ash, soil, and soap.

PubMed

Nizame, Fosiul A; Nasreen, Sharifa; Halder, Amal K; Arman, Shaila; Winch, Peter J; Unicomb, Leanne; Luby, Stephen P

2015-06-01

Bangladeshi communities have historically used ash and soil as handwashing agents. A structured observation study and qualitative interviews on the use of ash/soil and soap as handwashing agents were conducted in rural Bangladesh to help develop a handwashing promotion intervention. The observations were conducted among 1,000 randomly selected households from 36 districts. Fieldworkers observed people using ash/soil to wash their hand(s) on 13% of occasions after defecation and on 10% after cleaning a child's anus. This compares with 19% of people who used soap after defecation and 27% after cleaning a child who defecated. Using ash/soil or soap was rarely (< 1%) observed at other times recommended for handwashing. The qualitative study enrolled 24 households from three observation villages, where high usage of ash/soil for handwashing was detected. Most informants reported that ash/soil was used only for handwashing after fecal contact, and that ash/soil could clean hands as effectively as soap. © The American Society of Tropical Medicine and Hygiene.

Ash Emissions and Risk Management in the Pacific Ocean

NASA Astrophysics Data System (ADS)

Steensen, T. S.; Webley, P. W.; Stuefer, M.

2012-12-01

Located in the 'Ring of Fire', regions and communities around the Pacific Ocean often face volcanic eruptions and subsequent ash emissions. Volcanic ash clouds pose a significant risk to aviation, especially in the highly-frequented flight corridors around active volcano zones like Indonesia or Eastern Russia and the Alaskan Aleutian Islands. To mitigate and manage such events, a detailed quantitative analysis using a range of scientific measurements, including satellite data and Volcanic Ash Transport and Dispersion (VATD) model results, needs to be conducted in real-time. For the case study of the Sarychev Peak eruption in Russia's Kurile Islands during 2009, we compare ash loading and dispersion from Weather Research and Forecast model with online Chemistry (WRF-Chem) results with satellite data of the eruption. These parameters are needed for the real-time management of volcanic crises to outline no-fly zones and to predict the areas that the ash is most likely to reach in the near future. In the early stages after the eruption, an international group with representatives from the Kamchatkan and Sachalin Volcanic Eruption Response Teams (KVERT, SVERT), the National Aeronautics and Space Administration (NASA), and the Alaska Volcano Observatory (AVO) published early research on the geological and geophysical characteristics of the eruption and the behavior of the resulting ash clouds. The study presented here is a follow-up project aimed to implement VATD model results and satellite data retrospectively to demonstrate the possibilities to develop this approach in real-time for future eruptions. Our research finds that, although meteorological cloud coverage is high in those geographical regions and, consequently, these clouds can cover most of the ash clouds and as such prevent satellites from detecting it, both approaches compare well and supplement each other to reduce the risk of volcanic eruptions. We carry out spatial extent and absolute quantitative comparisons and analyze the sensitivity of model inputs, such as eruption rate and vertical particle size distributions. Our analysis shows that comparisons between real-time satellite observations and VATD model simulations is a complex and difficult process and we present several methods that could be used to reduce the hazards and be useful in any risk assessments.

Bubbles and Dust: Dissolution Rates of Unhydrated Volcanic Ash as a Function of Morphology, Composition, and Particle Size

NASA Astrophysics Data System (ADS)

Wygel, C. M.; Sahagian, D. L.

2017-12-01

Volcanic eruptions are natural hazards due to their explosive nature and widespread transportation and deposition of ash particles. After deposition and subsequent leaching in soils or water bodies, ash deposition positively (nutrients) and negatively (contaminants) impacts the health of flora and fauna, including humans. The effects of ash leachates have been difficult to replicate in field and laboratory studies due to the many complexities and differences between ash particles. Ash morphology is characteristic for each eruption, dependent upon eruption energy, and should play a critical role in determining leaching rates. Morphology reflects overall particle surface area, which is strongly influenced by the presence of surface dust. In addition, ash composition, which in part controls morphology and particle size, may also affect leaching rates. This study determines the extent to which ash morphology, surface area, composition, and particle size control ash dissolution rates. Further, it is necessary to determine whether compound vesicular ash particles permit water into their interior structures to understand if both the internal and external surface areas are available for leaching. To address this, six fresh, unhydrated ash samples from diverse volcanic environments and a large range in morphology, from Pele's spheres to vesicular compound ash, are tested in the laboratory. Ash morphology was characterized on the Scanning Electron Microscope (SEM) before and after leaching and surface area was quantified by Brunauer Emmett Teller (BET) analysis and with geometric calculations. Column Leachate Tests (CLT) were conducted to compare leaching rates over a range of basaltic to silicic ashes as a function of time and surface area, to recreate the effects of ash deposition in diverse volcanic environments. After the CLT, post-leaching water analyses were conducted by Ion Coupled Plasma-Mass Spectrometry (ICP-MS) and Ion Chromatography (IC). We find that leaching rates are correlated to characteristic surface area of ash particles.

Volcanic ash as an oceanic iron source and sink

NASA Astrophysics Data System (ADS)

Rogan, Nicholas; Achterberg, Eric P.; Le Moigne, Frédéric A. C.; Marsay, Chris M.; Tagliabue, Alessandro; Williams, Richard G.

2016-03-01

Volcanic ash deposition to the ocean forms a natural source of iron (Fe) to surface water microbial communities. Inputs of lithogenic material may also facilitate Fe removal through scavenging. Combining dissolved Fe (dFe) and thorium-234 observations alongside modeling, we investigate scavenging of Fe in the North Atlantic following the Eyjafjallajökull volcanic eruption. Under typical conditions biogenic particles dominate scavenging, whereas ash particles dominate during the eruption. The size of particles is important as smaller scavenging particles can become saturated with surface-associated ions. Model simulations indicate that ash deposition associated with Eyjafjallajökull likely led to net Fe removal. Our model suggests a threefold greater stimulation of biological activity if ash deposition had occurred later in the growing season when the region was Fe limited. The implications of ash particle scavenging, eruption timing, and particle saturation need to be considered when assessing the impact of ash deposition on the ocean Fe cycle and productivity.

Causes of Variability in the Effects of Vegetative Ash on Post-Fire Runoff and Erosion

NASA Astrophysics Data System (ADS)

Balfour, V.; Woods, S.

2008-12-01

Vegetative ash formed during forest wildfires has varying effects on post-fire runoff and erosion. In some cases the ash layer reduces runoff and erosion by storing rainfall and by protecting the soil surface from surface sealing and rainsplash detachment. In other cases, the ash layer increases runoff and erosion by forming a surface crust, clogging soil pores, and providing a ready source of highly erodible fine material. Since only a handful of studies have measured the hydrogeomorphic effect of ash, it is unclear whether the observed variability in its effect reflects initial spatial variability in the ash properties due to factors such as fuel type and fire severity, or differences that develop over time due to compaction and erosion or exposure of the ash to rainfall and air. The goal of our research was to determine if the observed differences in the effect of ash on runoff and erosion are due to: 1) variability in initial ash hydrologic properties due to differences in combustion temperature and fuel type, or 2) variability in ash hydrologic properties caused by mineralogical phase changes that develop after the ash is exposed to water. We created ash in the laboratory using wood and needles of Lodgepole pine (Pinus contorta), Ponderosa pine (Pinus Ponderosa) and Douglas fir (Pseudotsuga menziesii) and at 100° C temperature increments from 300 to 900° C. A subsample of ash from each fuel type / temperature combination was saturated, left undisturbed for 24 hours and then oven dried at 104° C. Dry and wetted ash samples were characterized in terms of: structure (using a scanning electron microscope), carbon content, mineralogy (using X-ray diffraction), porosity, water retention properties and hydraulic conductivity. Ash produced at the higher combustion temperatures from all three fuel types contained lime (CaO), which on wetting was transformed to portlandite (Ca(OH)2) and calcite (CaCO3). This mineralogical transformation resulted in irreversible hardening and crusting of the ash, and hardened ash had a significantly lower hydraulic conductivity than unhardened ash. Ash produced by high severity fires may undergo this same hardening and crusting process after it is wetted by rainfall whereas ash produced by lower severity fires will not, and this may explain in part the contrasting hydrogeomorphic effects of ash that have been reported in the literature.

Characterization of coal fly ash components by laser-induced breakdown spectroscopy

NASA Astrophysics Data System (ADS)

Ctvrtnickova, Tereza; Mateo, Mari-Paz; Yañez, Armando; Nicolas, Gines

2009-10-01

The high sensitivity of laser-induced breakdown spectroscopy (LIBS) for the detection of most of the fly ash components enables the analysis of these residues produced during the combustion of coal. Fly ash consists of oxides (SiO 2, Al 2O 3, Fe 2O 3, CaO…) and unburnt carbon which is the major determinant of combustion efficiency in coal fired boilers. For example, an excessive amount of residual carbon dispersed in the fly ash means a significant loss of energy (Styszko et al., 2004 [1]). Standard methods employed for the analysis of fly ash make not possible a control of boiler in real time. LIBS technique can significantly reduce the time of analysis, in some cases even an online detection can be performed. For this reason, some studies have been addressed in order to demonstrate the capability of the laser-induced breakdown spectroscopy technique for the detection of carbon content in high pressure conditions typical of thermal power plants (Noda et al., 2002 [2]) and for the monitoring of unburnt carbon for the boiler control in real time (Kurihara et al., 2003 [3]). In particular, the content of unburnt carbon is a valuable indicator for the control of fly ash quality and for the boiler combustion. Depending on this unburnt carbon content, fly ash can be disposed as an industrial waste or as a raw material for the production of concrete in the construction sector. In this study, analyses were performed on specimens of various forms of preparation. Pressed pellets were prepared with two different binders. Presented results concern the nature and amount of the binder used to pelletize the powder, and the laser-induced breakdown spectroscopy parameters and procedure required to draw calibration curves of elements from the fly ash. Analysis "on tape" was performed in order to establish the experimental conditions for the future "online analysis".

Evaluation of heat treatment schedules for emerald ash borer (Coleoptera: Buprestidae).

PubMed

Myers, Scott W; Fraser, Ivich; Mastro, Victor C

2009-12-01

The thermotolerance of the emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), was evaluated by subjecting larvae and prepupae to a number of time-temperature regimes. Three independent experiments were conducted during 2006 and 2007 by heating emerald ash borer infested firewood in laboratory ovens. Heat treatments were established based on the internal wood temperature. Treatments ranged from 45 to 65 degrees C for 30 and 60 min, and the ability of larvae to pupate and emerge as adults was used to evaluate the success of each treatment. A fourth experiment was conducted to examine heat treatments on exposed prepupae removed from logs and subjected to ambient temperatures of 50, 55, and 60 degrees C for 15, 30, 45, and 60 min. Results from the firewood experiments were consistent in the first experiment. Emergence data showed emerald ash borer larvae were capable of surviving a temperatures-time combination up to 60 degrees C for 30 min in wood. The 65 degrees C for 30 min treatment was, however, effective in preventing emerald ash borer emergence on both dates. Conversely, in the second experiment using saturated steam heat, complete mortality was achieved at 50 and 55 degrees C for both 30 and 60 min. Results from the prepupae experiment showed emerald ash borer survivorship in temperature-time combinations up to 55 degrees C for 30 min, and at 50 degrees C for 60 min; 60 degrees C for 15 min and longer was effective in preventing pupation in exposed prepupae. Overall results suggest that emerald ash borer survival is variable depending on heating conditions, and an internal wood temperature of 60 degrees C for 60 min should be considered the minimum for safe treatment for firewood.

Evaluation of fly ash pellets for phosphorus removal in a laboratory scale denitrifying bioreactor.

PubMed

Li, Shiyang; Cooke, Richard A; Huang, Xiangfeng; Christianson, Laura; Bhattarai, Rabin

2018-02-01

Nitrate and orthophosphate from agricultural activities contribute significantly to nutrient loading in surface water bodies around the world. This study evaluated the efficacy of woodchips and fly ash pellets in tandem to remove nitrate and orthophosphate from simulated agricultural runoff in flow-through tests. The fly ash pellets had previously been developed specifically for orthophosphate removal for this type of application, and the sorption bench testing showed a good promise for flow-through testing. The lab-scale horizontal-flow bioreactor used in this study consisted of an upstream column filled with woodchips followed by a downstream column filled with fly ash pellets (3 and 1 m lengths, respectively; both 0.15 m diameter). Using influent concentrations of 12 mg/L nitrate and 5 mg/L orthophosphate, the woodchip bioreactor section was able to remove 49-85% of the nitrate concentration at three hydraulic retention times ranging from 0.67 to 4.0 h. The nitrate removal rate for woodchips ranged from 40 to 49 g N/m 3 /d. Higher hydraulic retention times (i.e., smaller flow rates) corresponded with greater nitrate load reduction. The fly ash pellets showed relatively stable removal efficiency of 68-75% across all retention times. Total orthophosphate adsorption by the pellets was 0.059-0.114 mg P/g which was far less than the saturated capacity (1.69 mg/g; based on previous work). The fly ash pellets also removed some nitrate and the woodchips also removed some orthophosphate, but these reductions were not significant. Overall, woodchip denitrification followed by fly ash pellet P-sorption can be an effective treatment technology for nitrate and phosphate removal in subsurface drainage. Copyright © 2017 Elsevier Ltd. All rights reserved.

Wet-dry cycles effect on ash water repellency. A laboratory experiment.

NASA Astrophysics Data System (ADS)

Pereira, Paulo; Cerdà, Artemi; Oliva, Marc; Mataix, Jorge; Jordán, Antonio

2014-05-01

In the immediate period after the fire, the ash layer has a strong influence on soil hydrological processes, as runoff, infiltration and erosion. Ash is very dynamic in the space and time. Until the first rainfall periods, ash is (re)distributed by the wind. After it can cover the soil surface, infiltrate or transported to other areas by water transport (Pereira et al., 2013a, b). This will have strong implications on nutrient redistribution and vegetation recovery. Ash layer may affect soil water repellency in different ways, depending on fire severity, soil properties and vegetation. Ash produced at low temperatures after low-severity burning is usually hydrophobic (Bodi et al., 2011, 2012). Wet-dry cycles have implications on ash physical and chemical properties, changing their effects in space and time. The aim of this study is to analyse the effects of fire temperature and severity on ash water repellency. Pinus sylvestris needles were collected in a Lithuania forest in Dzukija National Park (53º 54' N and 24º 22' E), transported to laboratory and washed with deionized water to remove soil particles and other residues. Needle samples were dried during 24 hours and exposed to different temperatures: 200, 300, 400 and 500 ºC, during 2 hours. Ash colour was analysed according to the Munsell Soil Color charts. Ash was black (10 YR 2/1) at 200 ºC, very dark grey (10YR 3/1) at 300 ºC, gray (10YR 5/1) at 400 ºC and light gray (10YR 7/1) at 500 ºC. Ten samples of ash released after each treatment were placed in plastic dishes (50 mm in diameter) in an amount enough to form a 5 mm thick layer, and ash water repellency was measured according to the Water Drop Penetration Test. Later, ash was carefully wetted with 15 ml of deionized water and placed in an oven during 4 days (96 hours), as in Bodí et al. (2012). This procedure was repeated 5 times in order to observe the effects of wet-dry cycles in ash water repellency. The results showed significant differences among wet-dry cycles (Chi Sqr = 184.13 p <0.001) and among temperatures, immediately after treatments (Kruskal-Wallis test: H = 13.64, p<0.01) and after first wet-dry cycle (Kruskal-Wallis test: H =13.85 p<0.01). In the second (Kruskal-Wallis test: =5.80, p >0.05), third (Kruskal-Wallis test: H =3.07, p>0.05), fourth (Kruskal-Wallis test: H=0.75, p>0.05) and fifth (Kruskal-Wallis test: H =0.199, p<0.05) wet-dry cycles, ash water repellency did not show significant differences. After wetting, ash water repellency decreased substantially in the first cycle. These results suggest that wet-dry cycles have important impacts in the reduction of ash water repellency. Nevertheless, this reduction at least in the first cycle is different according to the temperature/severity. Black ash (200 ºC) water repellency was significantly higher than the other temperatures/severities. Further research will be carried out using burned soils and different species. References Bodi, M.B., Doerr, S., Cerda, A., Mataix-Solera, J. (2012) Hydrological effects of a layer of vegetation ash on underlying wettable and water repellent soil. Geoderma, 161, 14-23, 2011. DOI: 10.1016/j.geoderma.2012.01.006. Bodí, M.B., Mataix-Solera, J., Doerr, S.H., Cerdà, A. (2011). The wettability of ash from burned vegetation and its relationship to Mediterranean plant species type, burn severity and total organic carbon content. Geoderma 160, 599-607. DOI:10.1016/j.geoderma.2010.11.009. Pereira, P., Cerdà, A., Úbeda, X., Mataix-Solera, J. Arcenegui, V., Zavala, L. (2013a) Modelling the impacts of wildfire on ash thickness in a short-term period, Land Degradation and Development. DOI: 10.1002/ldr.2195. Pereira, P., Cerdà, A., Úbeda, X., Mataix-Solera, J., Jordan, A. Burguet, M. (2013b) Spatial models for monitoring the spatio-temporal evolution of ashes after fire - a case study of a burnt grassland in Lithuania, Solid Earth, 4, 153-165. DOI: 10.5194/se-4-153-2013.

Removal of cadmium from aqueous solutions using industrial coal fly ash-nZVI.

PubMed

Ma, Lixia; Wei, Qi; Chen, Yueqin; Song, Qiuyang; Sun, Conghui; Wang, Zhiqiang; Wu, Guanghong

2018-02-01

Batch experiments were conducted to test the effects of various solution properties, such as pH, temperature, initial concentration and anoxic and aerobic atmosphere, on Cd removal by nanoscale zerovalent iron (nZVI) supported on industrial coal fly ash. Cd (II) could be removed by adsorption on fly ash-nZVI in a very short time (5 min) with high removal rates (greater than 99.9%) over a wide range of concentration (5-100 mg l -1 ). Cd (II) was physically adsorbed on the surface of fly ash-nZVI. The preparation of fly ash-nZVI can incorporate the use of waste media, making the overall adsorbent more removal efficient and low cost.

Removal of cadmium from aqueous solutions using industrial coal fly ash-nZVI

PubMed Central

Ma, Lixia; Wei, Qi; Chen, Yueqin; Song, Qiuyang; Sun, Conghui; Wang, Zhiqiang

2018-01-01

Batch experiments were conducted to test the effects of various solution properties, such as pH, temperature, initial concentration and anoxic and aerobic atmosphere, on Cd removal by nanoscale zerovalent iron (nZVI) supported on industrial coal fly ash. Cd (II) could be removed by adsorption on fly ash-nZVI in a very short time (5 min) with high removal rates (greater than 99.9%) over a wide range of concentration (5–100 mg l−1). Cd (II) was physically adsorbed on the surface of fly ash-nZVI. The preparation of fly ash-nZVI can incorporate the use of waste media, making the overall adsorbent more removal efficient and low cost. PMID:29515830

Investigations of ash fouling with cattle wastes as reburn fuel in a small-scale boiler burner under transient conditions.

PubMed

Oh, Hyukjin; Annamalai, Kalyan; Sweeten, John M

2008-04-01

Fouling behavior under reburn conditions was investigated with cattle wastes (termed as feedlot biomass [FB]) and coal as reburn fuels under a transient condition and short-time operation. A small-scale (30 kW or 100,000 Btu/hr) boiler burner research facility was used for the reburn experiments. The fuels considered for these experiments were natural gas (NG) for the ashless case, pure coal, pure FB, and blends of coal and FB. Two parameters that were used to characterize the ash "fouling" were (1) the overall heat-transfer coefficient (OHTC) when burning NG and solid fuels as reburn fuels, and (2) the combustible loss through ash deposited on the surfaces of heat exchanger tubes and the bottom ash in the ash port. A new methodology is presented for determining ash-fouling behavior under transient conditions. Results on the OHTCs for solid reburn fuels are compared with the OHTCs for NG. It was found that the growth of the layer of ash depositions over longer periods typically lowers OHTC, and the increased concentration of ash in gas phase promotes radiation in high-temperature zones during initial periods while decreasing the heat transfer in low-temperature zones. The ash analyses indicated that the bottom ash in the ash port contained a smaller percentage of combustibles with a higher FB percentage in the fuels, indicating better performance compared with coal because small particles in FB burn faster and the FB has higher volatile matter on a dry ash-free basis promoting more burn out.

Higher Activities of Defense-Associated Enzymes may Contribute to Greater Resistance of Manchurian Ash to Emerald Ash Borer Than A closely Related and Susceptible Congener.

PubMed

Rigsby, Chad M; Herms, Daniel A; Bonello, Pierluigi; Cipollini, Don

2016-08-01

Emerald ash borer (EAB) is an invasive beetle native to Asia that infests and kills ash (Fraxinus spp.) in North America. Previous experiments indicated that larvae feeding on co-evolved, resistant Manchurian ash (F. mandshurica) have increased antioxidant and quinone-protective enzyme activities compared to larvae feeding on susceptible North American species. Here, we examined mechanisms of host-generated oxidative and quinone-based stress and other putative defenses in Manchurian ash and the closely related and chemically similar, but susceptible, black ash (F. nigra), with and without exogenous application of methyl jasmonate (MeJA) to induce resistance mechanisms. Peroxidase activities were 4.6-13.3 times higher in Manchurian than black ash, although both species appeared to express the same three peroxidase isozymes. Additionally, peroxidase-mediated protein cross-linking activity was stronger in Manchurian ash. Polyphenol oxidase, β-glucosidase, chitinase, and lipoxygenase activities also were greater in Manchurian ash, but only lipoxygenase activity increased with MeJA application. Phloem H 2 O 2 levels were similar and were increased by MeJA application in both species. Lastly, trypsin inhibitor activity was detected in methanol and water extracts that were not allowed to oxidize, indicating the presence of phenolic-based trypsin inhibitors. However, no proteinaceous trypsin inhibitor activity was detected in either species. In response to MeJA application, Manchurian ash had higher trypsin inhibitor activity than black ash using the unoxidized water extracts, but no treatment effects were detected using methanol extracts. Based on these results we hypothesize that peroxidases, lignin polymerization, and quinone generation contribute to the greater resistance to EAB displayed by Manchurian ash.

Improved prediction and tracking of volcanic ash clouds

USGS Publications Warehouse

Mastin, Larry G.; Webley, Peter

2009-01-01

During the past 30??years, more than 100 airplanes have inadvertently flown through clouds of volcanic ash from erupting volcanoes. Such encounters have caused millions of dollars in damage to the aircraft and have endangered the lives of tens of thousands of passengers. In a few severe cases, total engine failure resulted when ash was ingested into turbines and coating turbine blades. These incidents have prompted the establishment of cooperative efforts by the International Civil Aviation Organization and the volcanological community to provide rapid notification of eruptive activity, and to monitor and forecast the trajectories of ash clouds so that they can be avoided by air traffic. Ash-cloud properties such as plume height, ash concentration, and three-dimensional ash distribution have been monitored through non-conventional remote sensing techniques that are under active development. Forecasting the trajectories of ash clouds has required the development of volcanic ash transport and dispersion models that can calculate the path of an ash cloud over the scale of a continent or a hemisphere. Volcanological inputs to these models, such as plume height, mass eruption rate, eruption duration, ash distribution with altitude, and grain-size distribution, must be assigned in real time during an event, often with limited observations. Databases and protocols are currently being developed that allow for rapid assignment of such source parameters. In this paper, we summarize how an interdisciplinary working group on eruption source parameters has been instigating research to improve upon the current understanding of volcanic ash cloud characterization and predictions. Improved predictions of ash cloud movement and air fall will aid in making better hazard assessments for aviation and for public health and air quality. ?? 2008 Elsevier B.V.

Firing system modification to alter ash properties for reduction of deposition and slagging under low NOx firing conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, D.; Lewis, R.; Tobiasz, R.

1998-12-31

The composition and properties of ash formed during coal firing have a major impact on boiler performance. Higher ash content in the coal can mean higher costs associated with coal handling, transportation, ash removal and ash disposal along with higher costs due to the increased ash content`s deleterious effects on pulverizing, combustion and heat transfer. ABB C-E Services, Inc. has conducted research for many years on what might be done to minimize the adverse effects of ash on boiler performance. Recently, ABB C-E Services has studied the effects of firing system modifications on ash composition and properties and the effectmore » these firing system modifications have on overall furnace performance. The subject of this paper is the impact of the installation of the CFS Concentric Firing System on the propensity for boiler wall ash deposition. For this study, CFS yaw angles were varied and particle samples were collected at the waterwalls for the different yaw angles tested. These ash samples were analyzed for ash composition. The results showed that with a larger CFS yaw angle (the air stream directed more towards the boiler walls) the base/acid ratio, iron content and sulfur content of the particle samples collected at the waterwall were reduced. This effect is due to several contributing factors: (1) an oxidizing environment produced by injecting more air toward the walls; and (2) an aerodynamic change which impacts the particle combustion time/temperature history.« less

A brief review on fly ash and its use in surface engineering

NASA Astrophysics Data System (ADS)

Bhajantri, Vishwanath; Krishna, Prasad; Jambagi, Sudhakar

2018-04-01

Fly ash is a by-product obtained from coal power plants. Over the past two decades, handling this industrial waste has been a great challenge for many developing countries. However, this menace can be used in many industrial applications viz., civil, automobile and aerospace applications. In civil industry, the fly ash has been used in concreate to enhance the porosity that increases the curing time of the concrete. The fly ash has been gaining importance these days as a feedstock material for many thermal spray processes. In automobile sector, the fly ash has been used as a thermal barrier coating in IC engines, whereas in aerospace industry, which demands lighter and stronger materials, the fly ash has been used as a reinforcement material. Hence, so far, fly ash has been used as an either single or a composite feed stock material in thermal spray processes. The fly ash with other materials like alumina, titania and red mud have been deposited using thermal spray processes. These coatings have exhibited higher wear, corrosion and erosion resistance as compared to the uncoated specimens. In this paper, a brief review on fly ash and its use, especially its use as a feed stock in thermal spray coating, is presented. Therefore, the use of fly ash has opened a new frontier of research in thermal spray coating area where economically viable coatings can be produced using industrial waste like fly ash.

Firing system modification to alter ash properties for reduction of deposition and slagging under low NOx firing conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, D.; Lewis, R.; Tobiasz, R.

1998-07-01

The composition and properties of ash formed during coal firing have a major impact on boiler performance. Higher ash content in the coal can mean higher costs associated with coal handling, transportation, ash removal and ash disposal along with higher costs due to the increased ash content's deleterious effects on pulverizing, combustion and heat transfer. ABB C-E Services, Inc. has conducted research what might be done to minimize the adverse effects of ash on boiler performance for many years. Recently, ABB C-E Services has studied the effects of firing system modifications on ash composition and properties and the effect thesemore » firing system modifications have on overall furnace performance. The subject of this paper is the impact of the installation of the CFS{trademark} yaw angles were varied and particle samples were collected at the waterwalls for the different yaw angles tested. These ash samples were analyzed for ash composition. The results showed that with a larger CFS{trademark} yaw angle (the air stream directed more towards the boiler walls) the base/acid ratio, iron content and sulfur content of the particle samples collected at the waterwall were reduced. This effect is due to several contributing factors: (1) an oxidizing environment produced by injecting more air toward the walls; and (2) an aerodynamic change which impacts the particle combustion time/temperature history.« less

Peak exposures to main components of ash and gaseous diesel exhausts in closed and open ash loading stations at biomass-fuelled power plants.

PubMed

Laitinen, Juha; Koponen, Hanna; Sippula, Olli; Korpijärvi, Kirsi; Jumpponen, Mika; Laitinen, Sirpa; Aatamila, Marjaleena; Tissari, Jarkko; Karhunen, Tommi; Ojanen, Kari; Jokiniemi, Jorma; Korpinen, Leena

2017-10-01

Fly and bottom ashes are collected at power plants to reduce the environmental effects of energy production. However, handling the ashes causes health problems for operators, maintenance workers and truck drivers at the power plants. Hence, we evaluated ash loaders' peak inhalation exposures to the chemical components of ash and diesel exhausts in open and closed ash loading stations at biomass-fuelled combined heat and power plants. We also carried out chemical and morphological analyses of the ashes to evaluate their health hazard potential in order to find practical technical measures to reduce workers' exposure. On the basis of X-ray diffraction analyses, the main respirable crystalline ash compounds were SiO 2 , CaSO 4 , CaO, Ca 2 Al 2 SiO 7 , NaCl and Ca 3 Al 2 O 6 in the fly ashes and SiO 2 , KAlSi 3 O 8 , NaAlSi 3 O 8 and Ca 2 Al 2 SiO 7 in the bottom ashes. The short-term exposure levels of respirable crystalline silica, inhalable inorganic dust, Cr, Mn, Ni and nitric oxide exceeded their Finnish eight hours occupational exposure limit values in the closed ash loading station. According to our observations, more attention should be paid to the ash-moistening process, the use of tank trucks instead of open cassette flatbed trucks, and the sealing of the loading line from the silo to the truck which would prevent spreading the ash into the air. The idling time of diesel trucks should also be limited, and ash loading stations should be equipped with exhaust gas ventilators. If working conditions make it impossible to keep to the OEL values, workers must use respirators and protect their eyes and skin. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chronic exposure to coal fly ash causes minimal changes in corticosterone and testosterone concentrations in male southern toads Bufo terrestris

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, C.K.; Mendonca, M.T.

More than 50% of the electricity in the United States is produced by coal-burning power plants. The byproduct of coal-burning plants is coal fly ash, which contains increased concentrations of trace metals and is disposed of in collection basins. Southern toads (Bufo terrestris) frequently use these basins for reproduction. Male toads were collected in spring 2001 and 2002 from an ash basin and a reference site and divided into four groups: toads collected at the control site and maintained on (1) control substrate and food or (2) ash and contaminated food and toads collected at the ash site and maintainedmore » in (3) control or (4) ash conditions. Blood was collected periodically during 5 months to determine testosterone and corticosterone concentrations. Reference to ash toads exhibited a significant, transient increase in corticosterone at 4 weeks, but neither corticosterone nor testosterone continued to increase beyond this time. In contrast, toads caught and maintained on ash did not exhibit increased corticosterone. Testosterone in these toads appeared to be unrelated to ash exposure. This unexpected lack of a corticosterone response and no effect on testosterone suggests that toads chronically exposed to trace metals can acclimate to a polluted environment, but they may still experience subtle long-term consequences.« less

H2S adsorption by municipal solid waste incineration (MSWI) fly ash with heavy metals immobilization.

PubMed

Wu, Huanan; Zhu, Yu; Bian, Songwei; Ko, Jae Hac; Li, Sam Fong Yau; Xu, Qiyong

2018-03-01

As a byproduct of municipal solid waste incineration (MSWI) plant, fly ash is becoming a challenge for waste management in recent years. In this study, MSWI fly ash (FA) was evaluated for the potential capacity of odorous gas H 2 S removal. Results showed that fly ash demonstrated longer breakthrough time and higher H 2 S capacities than coal fly ash and sandy soil, due to its high content of alkali oxides of metals including heavy metals. H 2 S adsorption capacities of FA1 and FA2 were 15.89 and 12.59 mg H 2 S/g, respectively for 750 ppm H 2 S. The adsorption of H 2 S on fly ash led to formation of elemental sulfur and metal sulfide. More importantly, the formation of metal sulfide significantly reduced the leachability of heavy metals, such as Cr, Cu, Cd and Pb as shown by TCLP tests. The adsorption isotherms fit well with Langmuir model with the correlation coefficient over 0.99. The adsorption of H 2 S on fly ash features simultaneous H 2 S removal and stabilization and heavy metals found in most MSWI fly ash, making fly ash the potential low cost recycled sorbent material. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mechanically activated fly ash as a high performance binder for civil engineering

NASA Astrophysics Data System (ADS)

Rieger, D.; Kullová, L.; Čekalová, M.; Novotný, P.; Pola, M.

2017-01-01

This study is aimed for investigation of fly ash binder with suitable properties for civil engineering needs. The fly ash from Czech brown coal power plant Prunerov II was used and mechanically activated to achieve suitable particle size for alkaline activation of hardening process. This process is driven by dissolution of aluminosilicate content of fly ash and by subsequent development of inorganic polymeric network called geopolymer. Hardening kinetics at 25 and 30 °C were measured by strain controlled small amplitude oscillatory rheometry with strain of 0.01 % and microstructure of hardened binder was evaluated by scanning electron microscopy. Strength development of hardened binder was investigated according to compressional and flexural strength for a period of 180 days. Our investigation finds out, that mechanically activated fly ash can be comparable to metakaolin geopolymers, according to setting time and mechanical parameters even at room temperature curing. Moreover, on the bases of long time strength development, achieved compressional strength of 134.5 after 180 days is comparable to performance of high grade Portland cement concretes.

Size distribution of rare earth elements in coal ash

USGS Publications Warehouse

Scott, Clinton T.; Deonarine, Amrika; Kolker, Allan; Adams, Monique; Holland, James F.

2015-01-01

Rare earth elements (REEs) are utilized in various applications that are vital to the automotive, petrochemical, medical, and information technology industries. As world demand for REEs increases, critical shortages are expected. Due to the retention of REEs during coal combustion, coal fly ash is increasingly considered a potential resource. Previous studies have demonstrated that coal fly ash is variably enriched in REEs relative to feed coal (e.g, Seredin and Dai, 2012) and that enrichment increases with decreasing size fractions (Blissett et al., 2014). In order to further explore the REE resource potential of coal ash, and determine the partitioning behavior of REE as a function of grain size, we studied whole coal and fly ash size-fractions collected from three U.S commercial-scale coal-fired generating stations burning Appalachian or Powder River Basin coal. Whole fly ash was separated into , 5 um, to 5 to 10 um and 10 to 100 um particle size fractions by mechanical shaking using trace-metal clean procedures. In these samples REE enrichments in whole fly ash ranges 5.6 to 18.5 times that of feedcoals. Partitioning results for size separates relative to whole coal and whole fly ash will also be reported. 

A gas-phase chemiluminescence-based analyzer for waterborne arsenic

USGS Publications Warehouse

Idowu, A.D.; Dasgupta, P.K.; Genfa, Z.; Toda, K.; Garbarino, J.R.

2006-01-01

We show a practical sequential injection/zone fluidics-based analyzer that measures waterborne arsenic. The approach is capable of differentiating between inorganic As(III) and As(V). The principle is based on generating AsH 3 from the sample in a confined chamber by borohydride reduction at controlled pH, sparging the chamber to drive the AsH3 to a small reflective cell located atop a photomultiplier tube, allowing it to react with ozone generated from ambient air, and measuring the intense chemiluminescence that results. Arsine generation and removal from solution results in isolation from the sample matrix, avoiding the pitfalls encountered in some solution-based analysis techniques. The differential determination of As(III) and As(V) is based on the different pH dependence of the reducibility of these species to AsH3. At pH ???1, both As(III) and As(V) are quantitatively converted to arsine in the presence of NaBH4. At a pH of 4-5, only As(III) is converted to arsine. In the present form, the limit of detection (S/N = 3) is 0.05 ??g/L As at pH ???1 and 0.09 ??g/L As(III) at pH ???4-5 for a 3-mL sample. The analyzer is intrinsically automated and requires 4 min per determination. It is also possible to determine As(III) first at pH 4.5 and then determine the remaining As in a sequential manner; this requires 6 min. There are no significant practical interferences. A new borohydride solution formulation permits month-long reagent stability. ?? 2006 American Chemical Society.

Evaluation of trunk injections for control of emerald ash borer

Treesearch

Deborah G. McCullough; Therese M. Poland; David L. Cappaert; Phillip Lewis; John Molongowski

2005-01-01

In 2003, we evaluated trunk injections of imidacloprid for control of emerald ash borer (Agrilus planipennis Fairmaire) (EAB). Results were variable and indicated that efficacy could be affected by injection timing and method and by tree size and vigor. In 2004, we continued studies to assess the optimal timing for imidacloprid trunk injections and...

Residence of silver in mineral deposits of the Thunder Mountain caldera complex, Central Idaho, U.S.A.

USGS Publications Warehouse

Leonard, B.F.; Christian, R.P.

1987-01-01

Silver is an accessory element in gold, antimony, and tungsten deposits of the caldera complex. Most of the deposits are economically of low grade and genetically of xenothermal or epithermal character. Their gold- and silver-bearing minerals are usually disseminated, fine grained, and difficult to study. Sparsely disseminated pyrite and arsenoprite are common associates. Identified silver minerals are: native silver and electrum; the sulfides acanthite, argentite (the latter always inverted to acanthite), and members of the Silberkies group; the sulfosalts matildite, miargyrite, pyrargyrite, argentian tetrahedrite, and unnamed Ag-Sb-S and Ag-Fe-Sb-S minerals; the telluride hessite and the selenide naumannite; halides of the cerargyrite group; and the antimonate stetefeldtite. Suspected silver minerals include the sulfide uytenbogaardtite and the sulfosalts andorite, diaphorite, and polybasite. Electrum, acanthite, and argentian tetrahedrite are common, though nowhere abundant. The other silver minerals are rare. Silver is present as a minor element in the structure of some varieties of other minerals. These include arsenopyrite, chalcopyrite, chalcostibite, covelline, digenite, galena, sphalerite, and stibnite. The search for adventitious Ag in most of these minerals has been cursory. The results merely indicate that elemental silver is not confined to discrete silver minerals and is, therefore, an additional complication for the recovery of silver-bearing material from some deposits. Silver occurs cryptically in some plants of the region. At Red Mountain, for example, the ashed sapwood of Douglas-fir (Pseudotsuga menziesii) contains 2 to 300 ppm Ag. Silver in the ashed wood is roughly 100 times as abundant as it is in soil. The phenomenon, useful in biogeochemical exploration, deserves the attention of mineralogists. ?? 1987 Springer-Verlag.

Investigations of ash fouling with cattle wastes as reburn fuel in a small-scale boiler burner under transient conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hyukjin Oh; Kalyan Annamalai; John M. Sweeten

2008-04-15

Fouling behavior under reburn conditions was investigated with cattle wastes (termed as feedlot biomass, FB) and coal as reburn fuels under a transient condition and short-time operation. A small-scale (30 kW or 100,000 Btu/hr) boiler burner research facility was used for the reburn experiments. The fuels considered for these experiments were natural gas (NG) for the ashless case, pure coal, pure FB, and blends of coal and FB. Two parameters that were used to characterize the ash 'fouling' were (1) the overall heat-transfer coefficient (OHTC) when burning NG and solid fuels as reburn fuels, and (2) the combustible loss throughmore » ash deposited on the surfaces of heat exchanger tubes and the bottom ash in the ash port. A new methodology is presented for determining ash fouling behavior under transient conditions. Results on the OHTCs for solid reburn fuels are compared with the OHTCs for NG. It was found that the growth of the layer of ash depositions over longer periods typically lowers OHTC, and the increased concentration of ash in gas phase promotes radiation in high-temperature zones during initial periods while decreasing the heat transfer in low-temperature zones. The ash analyses indicated that the bottom ash in the ash port contained a smaller percentage of combustibles with a higher FB percentage in the fuels, indicating better performance compared with coal because small particles in FB burn faster and the FB has higher volatile matter on a dry ash-free basis promoting more burn out. 16 refs., 12 figs., 6 tabs.« less

Recycling of inorganic nutrients for hydroponic crop production following incineration of inedible biomass.

PubMed

Bubenheim, D L; Wignarajah, K

1997-01-01

The goal of resource recovery in a regenerative life support system is maintenance of product quality to sure support of reliable and predictable levels of life support function performance by the crop plant component. Further, these systems must be maintained over extended periods of time, requiring maintenance of nutrient solutions to avoid toxicity and deficiencies. The focus of this study was to determine the suitability of the ash product following incineration of inedible biomass as a source of inorganic nutrients for hydroponic crop production. Inedible wheat biomass was incinerated and ash quality characterized. The incinerator ash was dissolved in adequate nitric acid to establish a consistent nitrogen concentration is all nutrient solution treatments. Four experimental nutrient treatments were included: control, ash only, ash supplemented to match the control treatment, and ash only quality formulated with reagent grade chemicals. When nutrient solutions were formulated using only ash following incineration of inedible biomass, a balance in solution is established representing elemental retention following incineration and nutrient proportions present in the original biomass. The resulting solution is not identical to the control. This imbalance resulted in a suppression of crop growth. When the ash is supplemented with reagent grade chemicals to establish the same balance as in the control--growth is identical to the control. The ash appears to carry no phytotoxic materials. Growth in solution formulated with reagent grade chemicals but matching the quality of the ash only treatment resulted in similar growth to that of the ash only treatment. The ash product resulting from incineration of inedible biomass appears to be a suitable form for recycle of inorganic nutrients to crop production.

Artificial cloud test confirms volcanic ash detection using infrared spectral imaging

PubMed Central

Prata, A. J.; Dezitter, F.; Davies, I.; Weber, K.; Birnfeld, M.; Moriano, D.; Bernardo, C.; Vogel, A.; Prata, G. S.; Mather, T. A.; Thomas, H. E.; Cammas, J.; Weber, M.

2016-01-01

Airborne volcanic ash particles are a known hazard to aviation. Currently, there are no means available to detect ash in flight as the particles are too fine (radii < 30 μm) for on-board radar detection and, even in good visibility, ash clouds are difficult or impossible to detect by eye. The economic cost and societal impact of the April/May 2010 Icelandic eruption of Eyjafjallajökull generated renewed interest in finding ways to identify airborne volcanic ash in order to keep airspace open and avoid aircraft groundings. We have designed and built a bi-spectral, fast-sampling, uncooled infrared camera device (AVOID) to examine its ability to detect volcanic ash from commercial jet aircraft at distances of more than 50 km ahead. Here we report results of an experiment conducted over the Atlantic Ocean, off the coast of France, confirming the ability of the device to detect and quantify volcanic ash in an artificial ash cloud created by dispersal of volcanic ash from a second aircraft. A third aircraft was used to measure the ash in situ using optical particle counters. The cloud was composed of very fine ash (mean radii ~10 μm) collected from Iceland immediately after the Eyjafjallajökull eruption and had a vertical thickness of ~200 m, a width of ~2 km and length of between 2 and 12 km. Concentrations of ~200 μg m−3 were identified by AVOID at distances from ~20 km to ~70 km. For the first time, airborne remote detection of volcanic ash has been successfully demonstrated from a long-range flight test aircraft. PMID:27156701

Artificial cloud test confirms volcanic ash detection using infrared spectral imaging.

PubMed

Prata, A J; Dezitter, F; Davies, I; Weber, K; Birnfeld, M; Moriano, D; Bernardo, C; Vogel, A; Prata, G S; Mather, T A; Thomas, H E; Cammas, J; Weber, M

2016-05-09

Airborne volcanic ash particles are a known hazard to aviation. Currently, there are no means available to detect ash in flight as the particles are too fine (radii < 30 μm) for on-board radar detection and, even in good visibility, ash clouds are difficult or impossible to detect by eye. The economic cost and societal impact of the April/May 2010 Icelandic eruption of Eyjafjallajökull generated renewed interest in finding ways to identify airborne volcanic ash in order to keep airspace open and avoid aircraft groundings. We have designed and built a bi-spectral, fast-sampling, uncooled infrared camera device (AVOID) to examine its ability to detect volcanic ash from commercial jet aircraft at distances of more than 50 km ahead. Here we report results of an experiment conducted over the Atlantic Ocean, off the coast of France, confirming the ability of the device to detect and quantify volcanic ash in an artificial ash cloud created by dispersal of volcanic ash from a second aircraft. A third aircraft was used to measure the ash in situ using optical particle counters. The cloud was composed of very fine ash (mean radii ~10 μm) collected from Iceland immediately after the Eyjafjallajökull eruption and had a vertical thickness of ~200 m, a width of ~2 km and length of between 2 and 12 km. Concentrations of ~200 μg m(-3) were identified by AVOID at distances from ~20 km to ~70 km. For the first time, airborne remote detection of volcanic ash has been successfully demonstrated from a long-range flight test aircraft.

Characteristics of fly ashes from full-scale coal-fired power plants and their relationship to mercury adsorption

USGS Publications Warehouse

Lu, Y.; Rostam-Abadi, M.; Chang, R.; Richardson, C.; Paradis, J.

2007-01-01

Nine fly ash samples were collected from the particulate collection devices (baghouse or electrostatic precipitator) of four full-scale pulverized coal (PC) utility boilers burning eastern bituminous coals (EB-PC ashes) and three cyclone utility boilers burning either Powder River Basin (PRB) coals or PRB blends,(PRB-CYC ashes). As-received fly ash samples were mechanically sieved to obtain six size fractions. Unburned carbon (UBC) content, mercury content, and Brunauer-Emmett-Teller (BET)-N2 surface areas of as-received fly ashes and their size fractions were measured. In addition, UBC particles were examined by scanning electron microscopy, high-resolution transmission microscopy, and thermogravimetry to obtain information on their surface morphology, structure, and oxidation reactivity. It was found that the UBC particles contained amorphous carbon, ribbon-shaped graphitic carbon, and highly ordered graphite structures. The mercury contents of the UBCs (Hg/UBC, in ppm) in raw ash samples were comparable to those of the UBC-enriched samples, indicating that mercury was mainly adsorbed on the UBC in fly ash. The UBC content decreased with a decreasing particle size range for all nine ashes. There was no correlation between the mercury and UBC contents of different size fractions of as-received ashes. The mercury content of the UBCs in each size fraction, however, generally increased with a decreasing particle size for the nine ashes. The mercury contents and surface areas of the UBCs in the PRB-CYC ashes were about 8 and 3 times higher than UBCs in the EB-PC ashes, respectively. It appeared that both the particle size and surface area of UBC could contribute to mercury capture. The particle size of the UBC in PRB-CYC ash and thus the external mass transfer was found to be the major factor impacting the mercury adsorption. Both the particle size and surface reactivity of the UBC in EB-PC ash, which generally had a lower carbon oxidation reactivity than the PRB-PC ashes, appeared to be important for the mercury adsorption. ?? 2007 American Chemical Society.

Respiratory Health Effects of Volcanic Ash - a new Approach

NASA Astrophysics Data System (ADS)

Horwell, C. J.; Fenoglio, I.; Sparks, R. J.; Ragnarsdottir, K. V.; Fubini, B.

2003-12-01

Attempts to characterise the toxicity of volcanic ash have focused on the presence of the crystalline silica polymorph cristobalite, which is known to cause silicosis and lung cancer in industrial settings. Within the lung, it is the surface of the particles which will react with endogenous molecules. Free radicals, produced on particle surfaces, can react with DNA and other cellular components, instigating a chain of toxic events. For the first time, the ability of volcanic ash to form free radicals has been assessed using Electron Paramagnetic Resonance techniques specific to the hydroxyl radical. Respirable (< 4 microns) crystalline silica, separated from volcanic ash from the Soufriere Hills volcano, Montserrat, West Indies, did not produce hydroxyl free radicals or surface radicals. However, the ash, itself, generated up to 3 times more hydroxyl radicals than a quartz of known toxicity. The cause of the reactivity is reduced iron on the surface of iron-rich minerals such as amphiboles and pyroxenes. Fresh volcanic ash generates more free radicals than weathered volcanic ash which will have oxidised (and leached away) surface iron. These results have implications for volcanic health hazard research as it was previously assumed that volcanoes which did not produce respirable crystalline silica presented a lesser respiratory health hazard. The International Volcanic Health Hazard Network (IVHHN) promotes research into the health effects of volcanic emissions. Under the auspices of IVHHN, volcanic ash samples from volcanoes world-wide are being analysed for surface reactivity, grain-size distribution and composition to form a comprehensive database for use by volcano observatories, emergency managers, medical practitioners and researchers. The results will highlight volcanoes which have the potential to cause a respiratory health hazard through generation of iron-catalysed free radicals, as well as more conventional markers such as concentration of respirable particles. At the onset of new eruptions, the database will be used to aid the rapid assessment of health hazard from volcanic ash.

Long-range volcanic ash transport and fallout during the 2008 eruption of Chaiten volcano, Chile

NASA Astrophysics Data System (ADS)

Durant, A. J.; Prata, A. J.; Villarosa, G.; Rose, W. I.; Delmelle, P.; Viramonte, J.

2012-04-01

The May 2008 eruption of Chaitén volcano, Chile, provided a rare opportunity to measure the long-range transport of volcanic emissions and characteristics of a widely-dispersed terrestrial ash deposit. Airborne ash mass, quantified using thermal infrared satellite remote sensing, ranged between 0.2-0.4 Tg during the period 3-7 May 2008. A high level of spatiotemporal correspondence was observed between cloud trajectories and changes in surface reflectivity, which was inferred to indicate ash deposition. The evolution of the deposit was mapped for the first time using satellite-based observations of surface reflectivity. The distal (>80 km) ash deposit was poorly sorted and fine grained, and mean particle size varied very little beyond a distance >300 km. There were 3 consistent particle size subpopulations in fallout at distances >300 km which suggests that aggregation influenced particle settling. Discrete temporal sampling and characterisation of fallout demonstrated contributions from specific eruptive phases. Some evidence for winnowing was identified through comparison of samples collected at the time of deposition to bulk samples collected months after deposition. X-Ray Photoelectron Spectroscopy (XPS) analyses revealed surface enrichments in Ca, Na and Fe and the presence of coatings of mixed Ca-, Na- and Fe-rich salts on ash particles prior to deposition. XPS analyses revealed strong surface Fe enrichments (in contrast to the results from bulk leachate analyses), which indicates that surface analysis techniques should be applied to investigate potential influences on ocean productivity in response to volcanic ash fallout over oceans. Low S:Cl ratios in leachates indicate that the eruption had a low S content, and high Cl:F ratios imply gas-ash interaction within a Cl-rich environment. We estimate that ash fallout had potential to scavenge ~42 % of total S released into the atmosphere prior to deposition.

Biological effects of wood ash application to forest and aquatic ecosystems.

PubMed

Aronsson, K Andreas; Ekelund, Nils G A

2004-01-01

The present review aims to summarize current knowledge in the topic of wood ash application to boreal forest and aquatic ecosystems, and the different effects derived from these actions. Much research has been conducted regarding the effects of wood ash application on forest growth. Present studies show that, generally speaking, forest growth can be increased on wood ash-ameliorated peatland rich in nitrogen. On mineral soils, however, no change or even decreased growth have been reported. The effects on ground vegetation are not very clear, as well as the effects on fungi, soil microbes, and soil-decomposing animals. The discrepancies between different studies are for the most part explained by abiotic factors such as variation in fertility among sites, different degrees of stabilization, and wood ash dosage used, and different time scales among different studies. The lack of knowledge in the field of aquatic ecosystems and their response to ash application is an important issue for future research. The few studies conducted have mainly considered changes in water chemistry. The biotoxic effects of ash application can roughly be divided into two categories: primary and secondary. Among the primary effects is toxicity deriving from compounds in the wood ash and cadmium is probably the worst among these. The secondary effects of wood ash are generally due to its alkaline capacity and a release of ions into the soil and soil water, and finally, watercourses and lakes. Given current knowledge, we would recommend site- and wood ash-specific application practices, rather than broad and general guidelines for wood ash application to forests.

Remote observations of eruptive clouds and surface thermal activity during the 2009 eruption of Redoubt volcano

NASA Astrophysics Data System (ADS)

Webley, P. W.; Lopez, T. M.; Ekstrand, A. L.; Dean, K. G.; Rinkleff, P.; Dehn, J.; Cahill, C. F.; Wessels, R. L.; Bailey, J. E.; Izbekov, P.; Worden, A.

2013-06-01

Volcanoes often erupt explosively and generate a variety of hazards including volcanic ash clouds and gaseous plumes. These clouds and plumes are a significant hazard to the aviation industry and the ground features can be a major hazard to local communities. Here, we provide a chronology of the 2009 Redoubt Volcano eruption using frequent, low spatial resolution thermal infrared (TIR), mid-infrared (MIR) and ultraviolet (UV) satellite remote sensing data. The first explosion of the 2009 eruption of Redoubt Volcano occurred on March 15, 2009 (UTC) and was followed by a series of magmatic explosive events starting on March 23 (UTC). From March 23-April 4 2009, satellites imaged at least 19 separate explosive events that sent ash clouds up to 18 km above sea level (ASL) that dispersed ash across the Cook Inlet region. In this manuscript, we provide an overview of the ash clouds and plumes from the 19 explosive events, detailing their cloud-top heights and discussing the variations in infrared absorption signals. We show that the timing of the TIR data relative to the event end time was critical for inferring the TIR derived height and true cloud top height. The ash clouds were high in water content, likely in the form of ice, which masked the negative TIR brightness temperature difference (BTD) signal typically used for volcanic ash detection. The analysis shown here illustrates the utility of remote sensing data during volcanic crises to measure critical real-time parameters, such as cloud-top heights, changes in ground-based thermal activity, and plume/cloud location.

Experimental and numerical analysis of metal leaching from fly ash-amended highway bases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cetin, Bora; Aydilek, Ahmet H., E-mail: aydilek@umd.edu; Li, Lin

2012-05-15

Highlights: Black-Right-Pointing-Pointer This study is the evaluation of leaching potential of fly ash-lime mixed soils. Black-Right-Pointing-Pointer This objective is met with experimental and numerical analysis. Black-Right-Pointing-Pointer Zn leaching decreases with increase in fly ash content while Ba, B, Cu increases. Black-Right-Pointing-Pointer Decrease in lime content promoted leaching of Ba, B and Cu while Zn increases. Black-Right-Pointing-Pointer Numerical analysis predicted lower field metal concentrations. - Abstract: A study was conducted to evaluate the leaching potential of unpaved road materials (URM) mixed with lime activated high carbon fly ashes and to evaluate groundwater impacts of barium, boron, copper, and zinc leaching. Thismore » objective was met by a combination of batch water leach tests, column leach tests, and computer modeling. The laboratory tests were conducted on soil alone, fly ash alone, and URM-fly ash-lime kiln dust mixtures. The results indicated that an increase in fly ash and lime content has significant effects on leaching behavior of heavy metals from URM-fly ash mixture. An increase in fly ash content and a decrease in lime content promoted leaching of Ba, B and Cu whereas Zn leaching was primarily affected by the fly ash content. Numerically predicted field metal concentrations were significantly lower than the peak metal concentrations obtained in laboratory column leach tests, and field concentrations decreased with time and distance due to dispersion in soil vadose zone.« less

Physical characteristics, chemical composition and water contamination potential from Canadian wildfire ash

NASA Astrophysics Data System (ADS)

Santin, Cristina; Doerr, Stefan; Arcenegui, Vicky; Otero, Xose Luis

2017-04-01

Wildland fires leave a powdery residue on the ground: wildfire ash, which consists of mineral materials and charred organic components. Its quantities and characteristics depend mainly on the total amount and type of fuel burnt and the fire characteristics. Up to several tens of tons of ash per hectare have been quantified in different post-fire environments. As a new material present after a wildland fire, ash can have profound effects on ecosystems. It affects biogeochemical cycles, including the carbon cycle, stimulates microbial activity and helps the recovery of vegetation. Ash incorporated into the soil increases soil pH and nutrient pools temporarily and changes soil physical properties such as albedo, soil texture and hydraulic properties. Ash also modifies soil and landscape-scale hydrological behaviour. Its high porosity makes it very effective at absorbing rainfall, but it can also contribute to catastrophic debris flows when ash is mobilised by large storm events. Its 'fragile' nature makes ash very susceptible to wind and water erosion, facilitating its transfer to the hydrological system. Runoff containing ash from burnt areas carries soluble nutrients and pollutants, which can have detrimental impacts on aquatic ecosystems and the supply of potable water. In this presentation we will report for the first time on the physical characteristics, chemical composition and associated water pollution risk from ash produced in four typical Canadian boreal forest fires: two high-intensity fires in jack pine stands, and one high-intensity and one smouldering fire in black spruce stands.

Destruction kinetic of PCDDs/Fs in MSWI fly ash using microwave peroxide oxidation.

PubMed

Chang, Yu-Min; Fang, Wen-Bin; Tsai, Kuo-Sheng; Kao, Jimmy C M; Lin, Kae-Long; Chen, Ching-Ho

2015-01-01

Microwave peroxide oxidation is a less greenhouse gas emission and energy-efficient technology to destroy toxic organic compounds in hazardous waste. The research novelty is to adopt the innovative microwave peroxide oxidation in H2SO4/HNO3 solution to efficiently destroy the polychlorinated dibenzo-p-dioxins (PCDDs)/Fs in municipal solid waste incineration fly ash. The major objective of this paper is to study dynamic destruction of PCDDs/Fs using the microwave peroxide oxidation. Almost all PCDDs/Fs in the raw fly ash can be destructed in 120 min at a temperature of 423 K using the microwave peroxide oxidation treatment. It was found that the microwave peroxide oxidation provides the potential to destruct the PCDDs/Fs content in municipal solid waste incinerator (MSWI) fly ash to a low level as a function of treatment time. A useful kinetic correlation between destruction efficiency and treatment conditions is proposed on the basis of the experimental data obtained in this study. The significance of this work in terms of practical engineering applications is that the necessary minimum treatment time can be solved using a proposed graphic illustration method, by which the minimum treatment time is obtained if the desired destruction efficiency and treatment temperature are known. Because of inorganic salt dissolution, the temperature would be a critical factor facilitating the parts of fly ash dissolution. Material loss problem caused by the microwave peroxide oxidation and the effects of treatment time and temperature are also discussed in this paper.

New Zealand supereruption provides time marker for the Last Glacial Maximum in Antarctica

USGS Publications Warehouse

Dunbar, Nelia W.; Iverson, Nels A.; Van Eaton, Alexa R.; Sigl, Michael; Alloway, Brent V.; Kurbatov, Andrei V.; Mastin, Larry G.; McConnell, Joseph R.; Wilson, Colin J. N.

2017-01-01

Multiple, independent time markers are essential to correlate sediment and ice cores from the terrestrial, marine and glacial realms. These records constrain global paleoclimate reconstructions and inform future climate change scenarios. In the Northern Hemisphere, sub-visible layers of volcanic ash (cryptotephra) are valuable time markers due to their widespread dispersal and unique geochemical fingerprints. However, cryptotephra are not as widely identified in the Southern Hemisphere, leaving a gap in the climate record, particularly during the Last Glacial Maximum (LGM). Here we report the first identification of New Zealand volcanic ash in Antarctic ice. The Oruanui supereruption from Taupo volcano (25,580  ±  258 cal. a BP) provides a key time marker for the LGM in the New Zealand sector of the SW Pacific. This finding provides a high-precision chronological link to mid-latitude terrestrial and marine sites, and sheds light on the long-distance transport of tephra in the Southern Hemisphere. As occurred after identification of the Alaskan White River Ash in northern Europe, recognition of ash from the Oruanui eruption in Antarctica dramatically increases the reach and value of tephrochronology, providing links among climate records in widely different geographic areas and depositional environments.

Comparison between volcanic ash satellite retrievals and FALL3D transport model

NASA Astrophysics Data System (ADS)

Corradini, Stefano; Merucci, Luca; Folch, Arnau

2010-05-01

Volcanic eruptions represent one of the most important sources of natural pollution because of the large emission of gas and solid particles into the atmosphere. Volcanic clouds can contain different gas species (mainly H2O, CO2, SO2 and HCl) and a mix of silicate-bearing ash particles in the size range from 0.1 μm to few mm. Determining the properties, movement and extent of volcanic ash clouds is an important scientific, economic, and public safety issue because of the harmful effects on environment, public health and aviation. In particular, real-time tracking and forecasting of volcanic clouds is key for aviation safety. Several encounters of en-route aircrafts with volcanic ash clouds have demonstrated the harming effects of fine ash particles on modern aircrafts. Alongside these considerations, the economical consequences caused by disruption of airports must be also taken into account. Both security and economical issues require robust and affordable ash cloud detection and trajectory forecasting, ideally combining remote sensing and modeling. We perform a quantitative comparison between Moderate Resolution Imaging Spectroradiometer (MODIS) retrievals of volcanic ash cloud mass and Aerosol Optical Depth (AOD) with the FALL3D ash dispersal model. MODIS, aboard the NASA-Terra and NASA-Aqua polar satellites, is a multispectral instrument with 36 spectral bands from Visible (VIS) to Thermal InfraRed (TIR) and spatial resolution varying between 250 and 1000 m at nadir. The MODIS channels centered around 11 and 12 mm have been used for the ash retrievals through the Brightness Temperature Difference algorithm and MODTRAN simulations. FALL3D is a 3-D time-dependent Eulerian model for the transport and deposition of volcanic particles that outputs, among other variables, cloud column mass and AOD. We consider the Mt. Etna volcano 2002 eruptive event as a test case. Results show a good agreement between the mean AOT retrieved and the spatial ash dispersion in the different images, while the modeled FALL3D total mass retrieved results significantly overestimated.

Effects of Eyjafjallajökull Volcanic Ash on Innate Immune System Responses and Bacterial Growth in Vitro

PubMed Central

Baltrusaitis, Jonas; Powers, Linda S.; Borcherding, Jennifer A.; Caraballo, Juan C.; Mudunkotuwa, Imali; Peate, David W.; Walters, Katherine; Thompson, Jay M.; Grassian, Vicki H.; Gudmundsson, Gunnar; Comellas, Alejandro P.

2013-01-01

Background: On 20 March 2010, the Icelandic volcano Eyjafjallajökull erupted for the first time in 190 years. Despite many epidemiological reports showing effects of volcanic ash on the respiratory system, there are limited data evaluating cellular mechanisms involved in the response to ash. Epidemiological studies have observed an increase in respiratory infections in subjects and populations exposed to volcanic eruptions. Methods: We physicochemically characterized volcanic ash, finding various sizes of particles, as well as the presence of several transition metals, including iron. We examined the effect of Eyjafjallajökull ash on primary rat alveolar epithelial cells and human airway epithelial cells (20–100 µg/cm2), primary rat and human alveolar macrophages (5–20 µg/cm2), and Pseudomonas aeruginosa (PAO1) growth (3 µg/104 bacteria). Results: Volcanic ash had minimal effect on alveolar and airway epithelial cell integrity. In alveolar macrophages, volcanic ash disrupted pathogen-killing and inflammatory responses. In in vitro bacterial growth models, volcanic ash increased bacterial replication and decreased bacterial killing by antimicrobial peptides. Conclusions: These results provide potential biological plausibility for epidemiological data that show an association between air pollution exposure and the development of respiratory infections. These data suggest that volcanic ash exposure, while not seriously compromising lung cell function, may be able to impair innate immunity responses in exposed individuals. PMID:23478268

A retrospective study on acute health effects due to volcanic ash exposure during the eruption of Mount Etna (Sicily) in 2002.

PubMed

Lombardo, Daniele; Ciancio, Nicola; Campisi, Raffaele; Di Maria, Annalisa; Bivona, Laura; Poletti, Venerino; Mistretta, Antonio; Biggeri, Annibale; Di Maria, Giuseppe

2013-08-07

Mount Etna, located in the eastern part of Sicily (Italy), is the highest and most active volcano in Europe. During the sustained eruption that occurred in October-November 2002 huge amounts of volcanic ash fell on a densely populated area south-east of Mount Etna in Catania province. The volcanic ash fall caused extensive damage to infrastructure utilities and distress in the exposed population. This retrospective study evaluates whether or not there was an association between ash fall and acute health effects in exposed local communities. We collected the number and type of visits to the emergency department (ED) for diseases that could be related to volcanic ash exposure in public hospitals of the Province of Catania between October 20 and November 7, 2002. We compared the magnitude of differences in ED visits between the ash exposure period in 2002 and the same period of the previous year 2001. We observed a significant increase of ED visits for acute respiratory and cardiovascular diseases, and ocular disturbances during the ash exposure time period. There was a positive association between exposure to volcanic ash from the 2002 eruption of Mount Etna and acute health effects in the Catania residents. This study documents the need for public health preparedness and response initiatives to protect nearby populations from exposure to ash fall from future eruptions of Mount Etna.

Effects of Eyjafjallajökull volcanic ash on innate immune system responses and bacterial growth in vitro.

PubMed

Monick, Martha M; Baltrusaitis, Jonas; Powers, Linda S; Borcherding, Jennifer A; Caraballo, Juan C; Mudunkotuwa, Imali; Peate, David W; Walters, Katherine; Thompson, Jay M; Grassian, Vicki H; Gudmundsson, Gunnar; Comellas, Alejandro P

2013-06-01

On 20 March 2010, the Icelandic volcano Eyjafjallajökull erupted for the first time in 190 years. Despite many epidemiological reports showing effects of volcanic ash on the respiratory system, there are limited data evaluating cellular mechanisms involved in the response to ash. Epidemiological studies have observed an increase in respiratory infections in subjects and populations exposed to volcanic eruptions. We physicochemically characterized volcanic ash, finding various sizes of particles, as well as the presence of several transition metals, including iron. We examined the effect of Eyjafjallajökull ash on primary rat alveolar epithelial cells and human airway epithelial cells (20-100 µg/cm(2)), primary rat and human alveolar macrophages (5-20 µg/cm(2)), and Pseudomonas aeruginosa (PAO1) growth (3 µg/104 bacteria). Volcanic ash had minimal effect on alveolar and airway epithelial cell integrity. In alveolar macrophages, volcanic ash disrupted pathogen-killing and inflammatory responses. In in vitro bacterial growth models, volcanic ash increased bacterial replication and decreased bacterial killing by antimicrobial peptides. These results provide potential biological plausibility for epidemiological data that show an association between air pollution exposure and the development of respiratory infections. These data suggest that volcanic ash exposure, while not seriously compromising lung cell function, may be able to impair innate immunity responses in exposed individuals.

The effects of different types of nano-silicon dioxide additives on the properties of sludge ash mortar.

PubMed

Luo, Huan-Lin; Chang, Wei-Che; Lin, Deng-Fong

2009-04-01

To improve the drawbacks caused by the sludge ash replacement in mortar, the previous studies have shown that the early strength and durability of sludge ash/cement mortar are improved by adding nano-silicon dioxide (nano-SiO2) to mortar. In this article, three types of nano-SiO2--SS, HS, and SP (manufacturer code names)--were applied to sludge ash/cement mixture to make paste or mortar specimens. The object is to further extend the recycle of the sludge ash by determining the better type of nano-SiO2 additive to improve properties of sludge ash/ cement paste or mortar. The cement was replaced by 0, 10, 20, and 30% of sludge ash, and 0 and 2% of nano-SiO2 additives were added to the sludge ash paste or mortar specimens. Tests such as setting time, compressive strength, scanning electron microscopy, X-ray diffraction, nuclear magnetic resonance, and thermogravimetric analysis/differential thermal analysis were performed in this study. Test results show that nano-SiO2 additives can not only effectively increase the hydration product (calcium silicate hydrate [C-S-H] gel), but also make the crystal structure denser. Among the three types of nano-SiO2 additive, the SS type can best improve the properties of sludge ash/cement paste or mortar, followed by the SP and HS types.

Volcanic Ash Preservation in Prokosko Jezero, Boznia Herzegowina - Extending our Knowledge of Eruptions in the Adriatic Sea Area.

NASA Astrophysics Data System (ADS)

van den Bogaard, C.; Dörfler, W.

2017-12-01

Archaeological and palaeoecological studies of settlement phases and changes in society are often based on natural archives: changes in the sediment composition and pollen content reflect climatic developments, plant successions show human interactions with the landscape. Volcanic ash layers preserved in the archives form valuable time markers in archaeological studies, the data base is being enlarged rapidly. Here we report new results from a core from the Prokosko Jezero, Boznia Herzegowina, close to the Neolithic tell settlement at Okoliste. The core extends the European eruption record back into Late Glacial times. A total of at least 18 eruptive events are recorded in the core. No visible ash layers occur, 13 of the events are preserved as crypto-tephra layers, 5 as discrete layers. The ash particles have been provenance-fingerprinted by electron microprobe analysis and results are compared with published chemical measurements obtained from proximal and other distal sites within and around the Adriatic Sea. One of the aims of the present study was the timely correlation to other distal sites, comparing the overregional environmental development.

Rare and Rare-Earth Metals in Coal Processing Waste

NASA Astrophysics Data System (ADS)

Cherkasova, Tatiana; Cherkasova, Elizaveta; Tikhomirova, Anastasia; Bobrovni-kova, Alyona; Goryunova, Irina

2017-11-01

An urgent issue for power plants operating on solid fuels (coal) is the issue of utilization or use of accumulated production waste - ash and slag materials - in the related production. Ash-slag materials are classified as "waste", usually grade 5; tens of millions of tons of them being pro-duced annually in the Kemerovo region, which threatens the ecology of the region. At the same time, ash and slag is a very promising raw material. The use of this material as a base for the final product allows us to signifi-cantly expand the possibilities of using coal. The most widespread is the system of ash and slag involving in construction or as a replacement for sand in road construction, or as an additive to building mixtures. However, there are both industrially valuable and environmentally dangerous ele-ments in ash-slag materials. Ash-slag materials can be considered as inde-pendent ore deposits located on the surface and requiring the costs of their extraction.

Ash leaf metabolomes reveal differences between trees tolerant and susceptible to ash dieback disease.

PubMed

Sambles, Christine M; Salmon, Deborah L; Florance, Hannah; Howard, Thomas P; Smirnoff, Nicholas; Nielsen, Lene R; McKinney, Lea V; Kjær, Erik D; Buggs, Richard J A; Studholme, David J; Grant, Murray

2017-12-19

European common ash, Fraxinus excelsior, is currently threatened by Ash dieback (ADB) caused by the fungus, Hymenoscyphus fraxineus. To detect and identify metabolites that may be products of pathways important in contributing to resistance against H. fraxineus, we performed untargeted metabolomic profiling on leaves from five high-susceptibility and five low-susceptibility F. excelsior individuals identified during Danish field trials. We describe in this study, two datasets. The first is untargeted LC-MS metabolomics raw data from ash leaves with high-susceptibility and low-susceptibility to ADB in positive and negative mode. These data allow the application of peak picking, alignment, gap-filling and retention-time correlation analyses to be performed in alternative ways. The second, a processed dataset containing abundances of aligned features across all samples enables further mining of the data. Here we illustrate the utility of this dataset which has previously been used to identify putative iridoid glycosides, well known anti-herbivory terpenoid derivatives, and show differential abundance in tolerant and susceptible ash samples.

Ash leaf metabolomes reveal differences between trees tolerant and susceptible to ash dieback disease

PubMed Central

Sambles, Christine M.; Salmon, Deborah L.; Florance, Hannah; Howard, Thomas P.; Smirnoff, Nicholas; Nielsen, Lene R.; McKinney, Lea V.; Kjær, Erik D.; Buggs, Richard J. A.; Studholme, David J.; Grant, Murray

2017-01-01

European common ash, Fraxinus excelsior, is currently threatened by Ash dieback (ADB) caused by the fungus, Hymenoscyphus fraxineus. To detect and identify metabolites that may be products of pathways important in contributing to resistance against H. fraxineus, we performed untargeted metabolomic profiling on leaves from five high-susceptibility and five low-susceptibility F. excelsior individuals identified during Danish field trials. We describe in this study, two datasets. The first is untargeted LC-MS metabolomics raw data from ash leaves with high-susceptibility and low-susceptibility to ADB in positive and negative mode. These data allow the application of peak picking, alignment, gap-filling and retention-time correlation analyses to be performed in alternative ways. The second, a processed dataset containing abundances of aligned features across all samples enables further mining of the data. Here we illustrate the utility of this dataset which has previously been used to identify putative iridoid glycosides, well known anti-herbivory terpenoid derivatives, and show differential abundance in tolerant and susceptible ash samples. PMID:29257137

Emerald Ash Borer Threat Reveals Ecohydrologic Feedbacks in Northern U.S. Black Ash Wetlands

NASA Astrophysics Data System (ADS)

Diamond, J.; Mclaughlin, D. L.; Slesak, R.

2016-12-01

Hydrology is a primary driver of wetland structure and process that can be modified by abiotic and biotic feedbacks, leading to self-organization of wetland systems. Large-scale disturbance to these feedbacks, such as loss of vegetation, can thus be expected to impact wetland hydrology. The Emerald Ash Borer is an invasive beetle that is expected to cause widespread-loss of ash trees throughout the northern U.S. and Canada. To predict ecosystem response to this threat of vegetation loss, we ask if and how Black Ash (Fraxinus nigra), a ubiquitous facultative-wetland ash species, actively controls wetland hydrology to determine if Black Ash creates favorable hydrologic regimes for growth (i.e., evidence for ecohydrologic feedbacks). We do this by taking advantage of plot-level tree removal experiments in Black Ash-dominated (75-100% basal area) wetlands in the Chippewa National Forest, Minnesota. The monospecies dominance in these systems minimizes variation associated with species-specific effects, allowing for clearer interpretation of results regarding ecohydrologic feedbacks. Here, we present an analysis of six years of water table and soil moisture time series in experimental plots with the following treatments: 1) clear cut, 2) girdling, 3) group-selection thinning, and 4) control. We also present evapotranspiration (ET) time series estimates for each experimental plot using analysis of diel water level variation. Results show elevated water tables in treatment plots relative to control plots for all treatments for several years after treatments were applied, with differences as great as 50 cm. Some recovery of water table to pre-treatment levels was observed over time, but only the group-selection thinning treatment showed near-complete recovery to pre-treatment levels, and clear-cut treatments indicate sustained elevated water tables over five years. Differences among treatments are directly attributed to variably reduced ET relative to controls. Results also indicate changes to the ET vs. water table relationship among treatments, with implications for ET feedbacks to favorable hydrologic regimes for growth. Finally, we present a conceptual model for these ecosystems and discuss how the model will be used to explore ecohydrologic feedbacks in upcoming years.

Volcanic-ash hazard to aviation during the 2003-2004 eruptive activity of Anatahan volcano, Commonwealth of the Northern Mariana Islands

USGS Publications Warehouse

Guffanti, M.; Ewert, J.W.; Gallina, G.M.; Bluth, G.J.S.; Swanson, G.L.

2005-01-01

Within the Commonwealth of the Northern Mariana Islands (CNMI), Anatahan is one of nine active subaerial volcanoes that pose hazards to major air-traffic routes from airborne volcanic ash. The 2003-2004 eruptive activity of Anatahan volcano affected the region's aviation operations for 3 days in May 2003. On the first day of the eruption (10 May 2003), two international flights from Saipan to Japan were cancelled, and several flights implemented ash-avoidance procedures. On 13 May 2003, a high-altitude flight through volcanic gas was reported, with no perceptible damage to the aircraft. TOMS and MODIS analysis of satellite data strongly suggests that no significant ash and only minor amounts of SO2 were involved in the incident, consistent with crew observations. On 23 May 2003, airport operations were disrupted when tropical-cyclone winds dispersed ash to the south, dusting Saipan with light ashfall and causing flight cancellations there and at Guam 320 km south of the volcano. Operational (near-real-time) monitoring of ash clouds produced by Anatahan has been conducted since the first day of the eruption on 10 May 2003 by the Washington Volcanic Ash Advisory Center (VAAC). The VAAC was among the first groups outside of the immediate area of the volcano to detect and report on the unexpected eruption of Anatahan. After being contacted about an unusual cloud by National Weather Service forecasters in Guam at 1235 UTC on 10 May 2003, the VAAC analyzed GOES 9 images, confirming Anatahan as the likely source of an ash cloud and estimating that the eruption began at about 0730 UTC. The VAAC issued its first Volcanic Ash Advisory for Anatahan at 1300 UTC on 10 May 2003 more than 5 h after the start of the eruption, the delay reflecting the difficulty of detecting and confirming a surprise eruption at a remote volcano with no in situ real-time geophysical monitoring. The initial eruption plume reached 10.7-13.4 km (35,000-44,000 ft), well into jet cruise altitudes; thereafter, the maximum plume height decreased and during the rest of the eruption usually did not exceed ???5 km (???17,000 ft), which lessened the potential hazard to aircraft at higher cruise altitudes. Drifting ash clouds commonly extended hundreds of kilometers from the volcano, occasionally as far west as the Philippines. Over the course of the eruptive activity in 2003-2004, the VAAC issued 323 advisories (168 with graphical depictions of ash clouds) for Anatahan, serving as a reliable source of ash-cloud information for aviation-related meteorological offices and air carriers. With a record of frequent eruptions in the CNMI, continued satellite and in situ real-time geophysical monitoring is needed at Anatahan and other Marianas volcanoes so that potential hazards to aviation from any future eruptive activity can be quickly and correctly assessed. ?? 2005 Elsevier B.V. All rights reserved.

Volcanic-ash hazard to aviation during the 2003 2004 eruptive activity of Anatahan volcano, Commonwealth of the Northern Mariana Islands

NASA Astrophysics Data System (ADS)

Guffanti, Marianne; Ewert, John W.; Gallina, Gregory M.; Bluth, Gregg J. S.; Swanson, Grace L.

2005-08-01

Within the Commonwealth of the Northern Mariana Islands (CNMI), Anatahan is one of nine active subaerial volcanoes that pose hazards to major air-traffic routes from airborne volcanic ash. The 2003-2004 eruptive activity of Anatahan volcano affected the region's aviation operations for 3 days in May 2003. On the first day of the eruption (10 May 2003), two international flights from Saipan to Japan were cancelled, and several flights implemented ash-avoidance procedures. On 13 May 2003, a high-altitude flight through volcanic gas was reported, with no perceptible damage to the aircraft. TOMS and MODIS analysis of satellite data strongly suggests that no significant ash and only minor amounts of SO 2 were involved in the incident, consistent with crew observations. On 23 May 2003, airport operations were disrupted when tropical-cyclone winds dispersed ash to the south, dusting Saipan with light ashfall and causing flight cancellations there and at Guam 320 km south of the volcano. Operational (near-real-time) monitoring of ash clouds produced by Anatahan has been conducted since the first day of the eruption on 10 May 2003 by the Washington Volcanic Ash Advisory Center (VAAC). The VAAC was among the first groups outside of the immediate area of the volcano to detect and report on the unexpected eruption of Anatahan. After being contacted about an unusual cloud by National Weather Service forecasters in Guam at 1235 UTC on 10 May 2003, the VAAC analyzed GOES 9 images, confirming Anatahan as the likely source of an ash cloud and estimating that the eruption began at about 0730 UTC. The VAAC issued its first Volcanic Ash Advisory for Anatahan at 1300 UTC on 10 May 2003 more than 5 h after the start of the eruption, the delay reflecting the difficulty of detecting and confirming a surprise eruption at a remote volcano with no in situ real-time geophysical monitoring. The initial eruption plume reached 10.7-13.4 km (35,000-44,000 ft), well into jet cruise altitudes; thereafter, the maximum plume height decreased and during the rest of the eruption usually did not exceed ˜5 km (˜17,000 ft), which lessened the potential hazard to aircraft at higher cruise altitudes. Drifting ash clouds commonly extended hundreds of kilometers from the volcano, occasionally as far west as the Philippines. Over the course of the eruptive activity in 2003-2004, the VAAC issued 323 advisories (168 with graphical depictions of ash clouds) for Anatahan, serving as a reliable source of ash-cloud information for aviation-related meteorological offices and air carriers. With a record of frequent eruptions in the CNMI, continued satellite and in situ real-time geophysical monitoring is needed at Anatahan and other Marianas volcanoes so that potential hazards to aviation from any future eruptive activity can be quickly and correctly assessed.

Emergency hospital visits in association with volcanic ash, dust storms and other sources of ambient particles: a time-series study in Reykjavík, Iceland.

PubMed

Carlsen, Hanne Krage; Gislason, Thorarinn; Forsberg, Bertil; Meister, Kadri; Thorsteinsson, Throstur; Jóhannsson, Thorsteinn; Finnbjornsdottir, Ragnhildur; Oudin, Anna

2015-04-13

Volcanic ash contributed significantly to particulate matter (PM) in Iceland following the eruptions in Eyjafjallajökull 2010 and Grímsvötn 2011. This study aimed to investigate the association between different PM sources and emergency hospital visits for cardiorespiratory causes from 2007 to 2012. Indicators of PM10 sources; "volcanic ash", "dust storms", or "other sources" (traffic, fireworks, and re-suspension) on days when PM10 exceeded the daily air quality guideline value of 50 µg/m3 were entered into generalized additive models, adjusted for weather, time trend and co-pollutants. The average number of daily emergency hospital visits was 10.5. PM10 exceeded the air quality guideline value 115 out of 2191 days; 20 days due to volcanic ash, 14 due to dust storms (two days had both dust storm and ash contribution) and 83 due to other sources. High PM10 levels from volcanic ash tended to be significantly associated with the emergency hospital visits; estimates ranged from 4.8% (95% Confidence Interval (CI): 0.6, 9.2%) per day of exposure in unadjusted models to 7.3% (95% CI: -0.4, 15.5%) in adjusted models. Dust storms were not consistently associated with daily emergency hospital visits and other sources tended to show a negative association. We found some evidence indicating that volcanic ash particles were more harmful than particles from other sources, but the results were inconclusive and should be interpreted with caution.

The uk Lidar-sunphotometer operational volcanic ash monitoring network

NASA Astrophysics Data System (ADS)

Adam, Mariana; Buxmann, Joelle; Freeman, Nigel; Horseman, Andrew; Salmon, Christopher; Sugier, Jacqueline; Bennett, Richard

2018-04-01

The Met Office completed the deployment of ten lidars (UV Raman and depolarization), each accompanied by a sunphotometer (polarized model), to provide quantitative monitoring of volcanic ash over UK for VAAC London. The lidars provide range corrected signal and volume depolarization ratio in near-real time. The sunphotometers deliver aerosol optical depth, Ångstrom exponent and degree of linear polarization. Case study analyses of Saharan dust events (as a proxy for volcanic ash) are presented.

Foliar residue dynamics of azadirachtins following direct stem injection into white and green ash trees for control of emerald ash borer.

PubMed

Grimalt, Susana; Thompson, Dean; Chartrand, Derek; McFarlane, John; Helson, Blair; Lyons, Barry; Meating, Joe; Scarr, Taylor

2011-10-01

Azadirachtins are natural insecticides derived from the neem tree. The emerald ash borer (EAB) is an exotic invasive insect pest that infests various ash tree species and has the potential for significant economic, aesthetic and ecological impacts throughout North America. The initial translocation and foliar residue dynamics of azadirachtins were examined following direct injection into white and green ash trees growing in urban scenarios as a potential control for EAB. Substantial concentrations of azadirachtins A and B [mean maxima > 0.98 mg kg(-1) fresh weight (f.w.)] were observed within 2 days of injecting a specifically designed formulation of azadirachtins. Foliar residues declined exponentially through time, with half-life estimates ranging from 5.1 to 12.3 days. At the time of leaf senescence, foliar residue levels approximated 0.01 mg kg(-1) f.w., strongly mitigating the potential effects of non-target biota in soil or aquatic compartments. The magnitude and duration of exposures observed in this field study were considered to be above the thresholds required for biological effectiveness against both larval and adult life stages of EAB. Results support the use of azadirachtins as an environmentally acceptable systemic insecticide for control of EAB and protection of high-value ash trees in urban environments. Copyright © 2011 Society of Chemical Industry.

Spectra of confined positronium

NASA Astrophysics Data System (ADS)

Munjal, D.; Silotia, P.; Prasad, V.

2017-12-01

Positronium is studied under the effect of spherically confined plasma environment. Exponentially Cosine Screened Coulomb potential (ECSC) has been used to include the dense plasma screening effect on positronium. Time independent Schrodinger equation is solved numerically. Various physical parameters such as energy eigenvalues, radial matrix elements, oscillator strengths, and polarizability are well explored as a function of confinement parameters. Oscillator strength gets drastically modified under confinement. We have also obtained the results for Ps confined under spherically confined Debye potential and compared with results of ECSC potential. Also incidental degeneracy for different values of confinement parameters has been reported for the first time for positronium.

Illinois basin coal fly ashes. 1. Chemical characterization and solubility

USGS Publications Warehouse

Roy, W.R.; Griffin, R.A.; Dickerson, D.R.; Schuller, R.M.; Martin, S.M.C.

1984-01-01

Twelve precipitator-collected fly ash samples (nine derived from high-sulfur Illinois Basin coals and three from Western U.S. coals) were found to contain a variety of paraffins, aryl esters, phenols, and polynuclear aromatic hydrocarbons including phenanthrene, pyrene, and chrysene but all at very low concentrations. Less than 1% of the organic carbon in the samples was extractable into benzene. Solubility studies with a short-term (24-h) extraction procedure and a long-term (20-week) procedure indicate that the inorganic chemical composition of some types of fly ash effluent is time dependent and may be most toxic to aquatic ecosystems when initially mixed with water and pumped to disposal ponds. Some acidic, high-Cd fly ashes would be classified as hazardous wastes if coal ash was included in this waste category by future RCRA revisions. ?? 1984 American Chemical Society.

Compressive strength of concrete and mortar containing fly ash

DOEpatents

Liskowitz, J.W.; Wecharatana, M.; Jaturapitakkul, C.; Cerkanowicz, A.E.

1997-04-29

The present invention relates to concrete, mortar and other hardenable mixtures comprising cement and fly ash for use in construction. The invention includes a method for predicting the compressive strength of such a hardenable mixture, which is very important for planning a project. The invention also relates to hardenable mixtures comprising cement and fly ash which can achieve greater compressive strength than hardenable mixtures containing only concrete over the time period relevant for construction. In a specific embodiment, a formula is provided that accurately predicts compressive strength of concrete containing fly ash out to 180 days. In other specific examples, concrete and mortar containing about 15% to 25% fly ash as a replacement for cement, which are capable of meeting design specifications required for building and highway construction, are provided. Such materials can thus significantly reduce construction costs. 33 figs.

Compressive strength of concrete and mortar containing fly ash

DOEpatents

Liskowitz, J.W.; Wecharatana, M.; Jaturapitakkul, C.; Cerkanowicz, A.E.

1998-12-29

The present invention relates to concrete, mortar and other hardenable mixtures comprising cement and fly ash for use in construction. The invention includes a method for predicting the compressive strength of such a hardenable mixture, which is very important for planning a project. The invention also relates to hardenable mixtures comprising cement and fly ash which can achieve greater compressive strength than hardenable mixtures containing only concrete over the time period relevant for construction. In a specific embodiment, a formula is provided that accurately predicts compressive strength of concrete containing fly ash out to 180 days. In other specific examples, concrete and mortar containing about 15% to 25% fly ash as a replacement for cement, which are capable of meeting design specification required for building and highway construction, are provided. Such materials can thus significantly reduce construction costs. 33 figs.

Compressive strength of concrete and mortar containing fly ash

DOEpatents

Liskowitz, John W.; Wecharatana, Methi; Jaturapitakkul, Chai; Cerkanowicz, deceased, Anthony E.

1997-01-01

The present invention relates to concrete, mortar and other hardenable mixtures comprising cement and fly ash for use in construction. The invention includes a method for predicting the compressive strength of such a hardenable mixture, which is very important for planning a project. The invention also relates to hardenable mixtures comprising cement and fly ash which can achieve greater compressive strength than hardenable mixtures containing only concrete over the time period relevant for construction. In a specific embodiment, a formula is provided that accurately predicts compressive strength of concrete containing fly ash out to 180 days. In other specific examples, concrete and mortar containing about 15% to 25% fly ash as a replacement for cement, which are capable of meeting design specifications required for building and highway construction, are provided. Such materials can thus significantly reduce construction costs.

Compressive strength of concrete and mortar containing fly ash

DOEpatents

Liskowitz, John W.; Wecharatana, Methi; Jaturapitakkul, Chai; Cerkanowicz, deceased, Anthony E.

1998-01-01

The present invention relates to concrete, mortar and other hardenable mixtures comprising cement and fly ash for use in construction. The invention includes a method for predicting the compressive strength of such a hardenable mixture, which is very important for planning a project. The invention also relates to hardenable mixtures comprising cement and fly ash which can achieve greater compressive strength than hardenable mixtures containing only concrete over the time period relevant for construction. In a specific embodiment, a formula is provided that accurately predicts compressive strength of concrete containing fly ash out to 180 days. In other specific examples, concrete and mortar containing about 15% to 25% fly ash as a replacement for cement, which are capable of meeting design specification required for building and highway construction, are provided. Such materials can thus significantly reduce construction costs.

Indirect effects of emerald ash borer-induced ash mortality and canopy gap formation on epigaeic beetles.

PubMed

Gandhi, Kamal J K; Smith, Annemarie; Hartzler, Diane M; Herms, Daniel A

2014-06-01

Exotic herbivorous insects have drastically and irreversibly altered forest structure and composition of North American forests. For example, emerald ash borer (Agrilus planipennis Fairmaire) from Asia has caused wide-scale mortality of ash trees (Fraxinus spp.) in eastern United States and Canada. We studied the effects of forest changes resulting from emerald ash borer invasion on epigaeic or ground beetles (Coleoptera: Carabidae) along a gradient of ash dieback and gap sizes in southeastern Michigan. Ground beetles were sampled in hydric, mesic, and xeric habitats in which black (Fraxinus nigra Marshall), green (Fraxinus pennsylvanica Marshall), and white (Fraxinus americana L.) ash were the most common species, respectively. During 2006-2007, we trapped 2,545 adult ground beetles comprising 52 species. There was a negative correlation between percent ash tree mortality in 2006 and catches of all beetles. Catches of Agonum melanarium Dejean (in 2006) and Pterostichus mutus (Say) (in 2006-2007) were negatively correlated with tree mortality and gap size, respectively. However, catches of Pterostichus corvinus Dejean were positively correlated with gap size in 2006. As ash mortality and average gap size increased from 2006 to 2007, catches of all beetles as well as P. mutus and Pterostichus stygicus (Say) increased (1.3-3.9 times), while species diversity decreased, especially in mesic and xeric stands. Cluster analysis revealed that beetle assemblages in hydric and mesic stand diverged (25 and 40%, respectively) in their composition from 2006 to 2007, and that hydric stands had the most unique beetle assemblages. Overall, epigaeic beetle assemblages were altered in ash stands impacted by emerald ash borer; however, these impacts may dissipate as canopy gaps close.

Gypsum treated fly ash as a liner for waste disposal facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivapullaiah, Puvvadi V., E-mail: siva@civil.iisc.ernet.in; Baig, M. Arif Ali, E-mail: reach2arif@gmail.com

2011-02-15

Fly ash has potential application in the construction of base liners for waste containment facilities. While most of the fly ashes improve in the strength with curing, the ranges of permeabilities they attain may often not meet the basic requirement of a liner material. An attempt has been made in the present context to reduce the hydraulic conductivity by adding lime content up to 10% to two selected samples of class F fly ashes. The use of gypsum, which is known to accelerate the unconfined compressive strength by increasing the lime reactivity, has been investigated in further improving the hydraulicmore » conductivity. Hydraulic conductivities of the compacted specimens have been determined in the laboratory using the falling head method. It has been observed that the addition of gypsum reduces the hydraulic conductivity of the lime treated fly ashes. The reduction in the hydraulic conductivity of the samples containing gypsum is significantly more for samples with high amounts of lime contents (as high as 1000 times) than those fly ashes with lower amounts of lime. However there is a relatively more increase in the strengths of the samples with the inclusion of gypsum to the fly ashes at lower lime contents. This is due to the fact that excess lime added to fly ash is not effectively converted into pozzolanic compounds. Even the presence of gypsum is observed not to activate these reactions with excess lime. On the other hand the higher amount of lime in the presence of sulphate is observed to produce more cementitious compounds which block the pores in the fly ash. The consequent reduction in the hydraulic conductivity of fly ash would be beneficial in reducing the leachability of trace elements present in the fly ash when used as a base liner.« less

Environmental impact assessment of wood ash utilization in forest road construction and maintenance--A field study.

PubMed

Oburger, Eva; Jäger, Anna; Pasch, Alexander; Dellantonio, Alex; Stampfer, Karl; Wenzel, Walter W

2016-02-15

The ever increasing use of wood material as fuel for green energy production requires innovative, environmentally safe strategies for recycling of the remaining wood ash. Utilizing wood ash in forest road construction and maintenance to improve mechanical stability has been suggested as a feasible recycling option. To investigate the environmental impact of wood ash application in forest road maintenance, a two-year field experiment was conducted at two Austrian forest sites (Kobernausserwald (KO) (soil pH 5.5) and Weyregg (WE) (pH 7.7)) differing in their soil chemical properties. Two different ashes, one produced by grate incineration (GA) and the other by fluidized bed incineration in a mixture with 15 vol% burnt lime (FBA), were incorporated in repeated road sections at a 15:85% (V/V) ash-to-soil rate. Leaching waters from the road body were collected and analyzed for 32 environmentally relevant parameters over two years. Upon termination of the experiment, sub-road soil samples were collected and analyzed for ash-related changes in soil chemistry. Even though a larger number of parameters was affected by the ash application at the alkaline site (WE), we observed the most pronounced initial increases of pH as well as Al, As, Fe, Mn, Ni, Co, Cu, Mo, and NO2(−) concentrations in leachates beneath GA-treated road bodies at Kobernausserwald due to the lower soil buffer capacity at this site. Despite the observed effects our results indicate that, when specific requirements are met (i.e. appropriate ash quality, sufficient soil buffer capacity below the road body, and single time-point ash incorporation within several decades), wood ash application in forest road construction is generally environmentally acceptable.

Selenium poisoning of fish by coal ash wastewater in Herrington Lake, Kentucky.

PubMed

Lemly, A Dennis

2018-04-15

Selenium pollution from the E.W. Brown Electric Generating Station was investigated in Herrington Lake, KY. Coal ash wastewater is discharged as surface water overflow from ash disposal ponds into the lake via a National Pollutant Discharge Elimination System permit issued by the Kentucky Division of Water, but the permit does not restrict or limit the amount of selenium released. Unpermitted discharges occur from seeps and drainage through leaks in ash pond dams. Together, these discharges have resulted in selenium concentrations in water, sediment, benthic macroinvertebrates, and fish that are 2-9 times the level that is toxic for fish reproduction and survival. A large proportion (12.2%, or 25 times background) of juvenile largemouth bass (Micropterus salmoides, the only species examined) exhibited spinal and/or craniofacial malformations that are consistent with selenium poisoning. Teratogenic Deformity Index values indicated a 3.05% population-level impact on the bass fishery, with total selenium-induced mortality (including pre-swimup mortality) estimated to be in excess of 25% per year. These findings confirm that coal ash discharges into Herrington Lake are contributing selenium to the Lake that is poisoning fish. Copyright © 2017 Elsevier Inc. All rights reserved.

Analysis of Gene Expression in Emerald Ash Borer (Agrilus planipennis) Using Quantitative Real Time-PCR

PubMed Central

Bhandary, Binny; Rajarapu, Swapna Priya; Rivera-Vega, Loren; Mittapalli, Omprakash

2010-01-01

Emerald ash borer (EAB, Agrilus planipennis) is an exotic invasive pest, which has killed millions of ash trees (Fraxinus spp) in North America.EAB continues to spread rapidly and attacks ash trees of different ages, from saplings to mature trees. However, to date very little or no molecular knowledge exists for EAB. We are interested in deciphering the molecular-based physiological processes at the tissue level that aid EAB in successful colonization of ash trees. In this report we show the effective use of quantitative real-time PCR (qRT-PCR) to ascertain mRNA levels in different larval tissues (including midgut, fat bodies and cuticle) and different developmental stages (including 1st-, 2nd-, 3rd-, 4th-instars, prepupae and adults) of EAB. As an example, a peritrophin gene (herein named, AP-PERI1) is exemplified as the gene of interest and a ribosomal protein (AP-RP1) as the internal control. Peritrophins are important components of the peritrophic membrane/matrix (PM), which is the lining of the insect gut. The PM has diverse functions including digestion and mechanical protection to the midgut epithelium. PMID:20445495

Analysis of gene expression in emerald ash borer (Agrilus planipennis) using quantitative real time-PCR.

PubMed

Bhandary, Binny; Rajarapu, Swapna Priya; Rivera-Vega, Loren; Mittapalli, Omprakash

2010-05-04

Emerald ash borer (EAB, Agrilus planipennis) is an exotic invasive pest, which has killed millions of ash trees (Fraxinus spp) in North America. EAB continues to spread rapidly and attacks ash trees of different ages, from saplings to mature trees. However, to date very little or no molecular knowledge exists for EAB. We are interested in deciphering the molecular-based physiological processes at the tissue level that aid EAB in successful colonization of ash trees. In this report we show the effective use of quantitative real-time PCR (qRT-PCR) to ascertain mRNA levels in different larval tissues (including midgut, fat bodies and cuticle) and different developmental stages (including 1(st)-, 2(nd)-, 3(rd)-, 4(th)-instars, prepupae and adults) of EAB. As an example, a peritrophin gene (herein named, AP-PERI1) is exemplified as the gene of interest and a ribosomal protein (AP-RP1) as the internal control. Peritrophins are important components of the peritrophic membrane/matrix (PM), which is the lining of the insect gut. The PM has diverse functions including digestion and mechanical protection to the midgut epithelium.

Arsenic removal from water using a novel amorphous adsorbent developed from coal fly ash.

PubMed

Zhang, Kaihua; Zhang, Dongxue; Zhang, Kai

2016-01-01

A novel effective adsorbent of alumina/silica oxide hydrate (ASOH) for arsenic removal was developed through simple chemical reactions using coal fly ash. The iron-modified ASOH with enhancing adsorption activity was further developed from raw fly ash based on the in situ technique. The adsorbents were characterized by X-ray diffraction, Fourier transform infrared spectrometry, scanning electron micrograph, laser particle size and Brunauer-Emmet-Teller surface area. The results show that the adsorbents are in amorphous and porous structure, the surface areas of which are 8-12 times that of the raw ash. The acidic hydrothermal treatment acts an important role in the formation of the amorphous structure of ASOH rather than zeolite crystal. A series of adsorption experiments for arsenic on them were studied. ASOH can achieve a high removal efficiency for arsenic of 96.4% from water, which is more than 2.5 times that of the raw ash. Iron-modified ASOH can enhance the removal efficiency to reach 99.8% due to the in situ loading of iron (Fe). The condition of synthesis pH = 2-4 is better for iron-modified ASOH to adsorb arsenic from water.

Valorization of MSWI bottom ash for biogas desulfurization: Influence of biogas water content.

PubMed

Fontseré Obis, Marta; Germain, Patrick; Troesch, Olivier; Spillemaecker, Michel; Benbelkacem, Hassen

2017-02-01

In this study an alternative valorization of Municipal Solid Waste Incineration (MSWI) Bottom Ash (BA) for H 2 S elimination from landfill biogas was evaluated. Emphasis was given to the influence of water content in biogas on H 2 S removal efficiency by BA. A small-scale pilot was developed and implemented in a landfill site located in France. A new biogas analyzer was used and allowed real-time continuous measurement of CH 4 , CO 2 , O 2 , H 2 S and H 2 O in raw and treated biogas. The H 2 S removal efficiency of bottom ash was evaluated for different inlet biogas humidities: from 4 to 24g water /m 3 . The biogas water content was found to greatly affect bottom ash efficiency regarding H 2 S removal. With humid inlet biogas the H 2 S removal was almost 3 times higher than with a dry inlet biogas. Best removal capacity obtained was 56gH 2 S/kgdryBA. A humid inlet biogas allows to conserve the bottom ash moisture content for a maximum H 2 S retention. Copyright © 2016 Elsevier Ltd. All rights reserved.

Spain as an emergency air traffic hub during volcanic air fall events? Evidence of past volcanic ash air fall over Europe during the late Pleistocene

NASA Astrophysics Data System (ADS)

Hardiman, Mark; Lane, Christine; Blockley, Simon P. E.; Moreno, Ana; Valero-Garcés, Blas; Ortiz, José E.; Torres, Trino; Lowe, John J.; Menzies, Martin A.

2010-05-01

Past volcanic eruptions often leave visible ash layers in the geological record, for example in marine or lake sedimentary sequences. Recent developments, however, have shown that non-visible volcanic ash layers are also commonly preserved in sedimentary deposits. These augment the record of past volcanic events by demonstrating that past ash dispersals have been more numerous and widely disseminated in Europe than previously appreciated. The dispersal ‘footprints' of some large late Pleistocene European eruptions are examined here in the light of the recent Eyjafjallajökull eruption. For example, the Vedde Ash which was erupted from Iceland around 12 thousand years ago, delivered distal (and non-visible) glass deposits as far south as Switzerland and as far east as the Ural Mountains in Russia, with an overall European distribution remarkably similar to the dominant tracks of the recent Eyjafjallajökull plumes. The Eyjafjallajökull eruption has demonstrated that relatively small amounts of distal volcanic ash in the atmosphere can seriously disrupt aviation activity, with attendant economic and other consequences. It has raised fundamental questions about the likelihood of larger or more prolonged volcanic activity in the near future, and the possibility of even more serious consequences than those experienced recently. Given that there are several other volcanic centres that could cause such disruption in Europe (e.g. Campania and other volcanic centres in Italy; Aegean volcanoes), a key question is whether there are parts of Europe less prone to ash plumes and which could therefore operate as emergency air traffic hubs during times of ash dispersal. Although not generated to answer this question, the recent geological record might provide a basis for seeking the answer. For example, four palaeo-records covering the time frame of 8 - 40 Ka BP that are geographically distributed across Spain have been examined for non-visible distal ash content. All four have proved to be almost devoid of volcanic ash, which contrasts with results obtained from sites throughout central and northern Europe. This suggests that Spain has remained free of ashfall events throughout the late Pleistocene, or that any ash dispersal over Spain has been short-lived and/or infrequent. This appears to accord with the pattern of dispersal of Eyjafjallajökull ash clouds over April to May 2010. Most of the active period was characterised by low eruptive columns and the tropospheric dispersal of ash. Under these conditions, ash dispersal was multi-directional from eastern Europe to Greenland and beyond, but did not encroach on to the Iberian peninsula. In contrast, when the eruptive columns became more elevated and entrained in the jet stream, the dispersal directions were more uni-directional and passed over Iberia and North Africa. Thus the apparent lack of volcanic ash in Iberia (10 - 40ka) may have as much to do with eruptive column height and volcano location as with circulation patterns (tropospheric v. stratospheric). A more comprehensive assessment of geological records of non-visible ash layers in selected sites may hold the key to examining this matter more robustly.

Ash formation, deposition, corrosion, and erosion in conventional boilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benson, S.A.; Jones, M.L.

1995-12-01

The inorganic components (ash-forming species) associated with coals significantly affect boiler design, efficiency of operation, and lifetimes of boiler parts. During combustion in conventional pulverized fuel boilers, the inorganic components are transformed into inorganic gases, liquids, and solids. This partitioning depends upon the association of the inorganic components in the coal and combustion conditions. The inorganic components are associated as mineral grains and as organically associated elements, and these associations of inorganic components in the fuel directly influence their fate upon combustion. Combustion conditions, such as temperature and atmosphere, influence the volatility and the interaction of inorganic components during combustionmore » and gas cooling, which influences the state and size composition distribution of the particulate and condensed ash species. The intermediate species are transported with the bulk gas flow through the combustion systems, during which time the gases and entrained ash are cooled. Deposition, corrosion, and erosion occur when the ash intermediate species are transported to the heat-transfer surface, react with the surface, accumulate, sinter, and develop strength. Research over the past decade has significantly advanced understanding of ash formation, deposition, corrosion, and erosion mechanisms. Many of the advances in understanding and predicting ash-related issues can be attributed to advanced analytical methods to determine the inorganic composition of fuels and the resulting ash materials. These new analytical techniques have been the key to elucidation of the mechanisms of ash formation and deposition. This information has been used to develop algorithms and computer models to predict the effects of ash on combustion system performance.« less

Hydrologic conditions controlling runoff generation immediately after wildfire

USGS Publications Warehouse

Ebel, Brian A.; Moody, John A.; Martin, Deborah A.

2012-01-01

We investigated the control of postwildfire runoff by physical and hydraulic properties of soil, hydrologic states, and an ash layer immediately following wildfire. The field site is within the area burned by the 2010 Fourmile Canyon Fire in Colorado, USA. Physical and hydraulic property characterization included ash thickness, particle size distribution, hydraulic conductivity, and soil water retention curves. Soil water content and matric potential were measured indirectly at several depths below the soil surface to document hydrologic states underneath the ash layer in the unsaturated zone, whereas precipitation and surface runoff were measured directly. Measurements of soil water content showed that almost no water infiltrated below the ash layer into the near-surface soil in the burned site at the storm time scale (i.e., minutes to hours). Runoff generation processes were controlled by and highly sensitive to ash thickness and ash hydraulic properties. The ash layer stored from 97% to 99% of rainfall, which was critical for reducing runoff amounts. The hydrologic response to two rain storms with different rainfall amounts, rainfall intensity, and durations, only ten days apart, indicated that runoff generation was predominantly by the saturation-excess mechanism perched at the ash-soil interface during the first storm and predominantly by the infiltration-excess mechanism at the ash surface during the second storm. Contributing area was not static for the two storms and was 4% (saturation excess) to 68% (infiltration excess) of the catchment area. Our results showed the importance of including hydrologic conditions and hydraulic properties of the ash layer in postwildfire runoff generation models.

[Novel process utilizing alkalis assisted hydrothermal process to stabilize heavy metals both from municipal solid waste or medical waste incinerator fly ash and waste water].

PubMed

Wang, Lei; Jin, Jian; Li, Xiao-dong; Chi, Yong; Yan, Jian-hua

2010-08-01

An alkalis assisted hydrothermal process was induced to stabilize heavy metals both from municipal solid waste or medical waste incinerator fly ash and waste water. The results showed that alkalis assisted hydrothermal process removed the heavy metals effectively from the waste water, and reduced leachability of fly ash after process. The heavy metal leachabilities of fly ash studied in this paper were Mn 17,300 microg/L,Ni 1650 microg/L, Cu 2560 microg/L, Zn 189,000 microg/L, Cd 1970 microg/L, Pb 1560 microg/L for medical waste incinerator fly ash; Mn 17.2 microg/L, Ni 8.32 microg/L, Cu 235.2 microg/L, Zn 668.3 microg/L, Cd 2.81 microg/L, Pb 7200 microg/L for municipal solid waste incinerator fly ash. After hydrothermal process with experimental condition [Na2CO3 dosage (5 g Na2CO3/50 g fly ash), reaction time = 10 h, L/S ratio = 10/1], the heavy metal removal efficiencies of medical waste incinerator fly ash were 86.2%-97.3%, and 94.7%-99.6% for municipal solid waste incinerator fly ash. The leachabilities of both two kinds of fly ash were lower than that of the Chinese national limit. The mechanism of heavy metal stabilization can be concluded to the chemisorption and physically encapsulation effects of aluminosilicates during its formation, crystallization and aging process, the high pH value has some contribution to the heavy metal removal and stabilization.

Influence of Blended Cements with Calcareous Fly Ash on Chloride Ion Migration and Carbonation Resistance of Concrete for Durable Structures.

PubMed

Glinicki, Michał A; Jóźwiak-Niedźwiedzka, Daria; Gibas, Karolina; Dąbrowski, Mariusz

2016-01-02

The objective of this paper is to examine the possible use of new blended cements containing calcareous fly ash in structural concrete, potentially adequate for structural elements of nuclear power plants. The investigation included five new cements made with different contents of non-clinker constituents: calcareous fly ash, siliceous fly ash, ground granulated blastfurnace slag, and a reference cement-ordinary Portland cement. The influence of innovative cements on the resistance of concrete to chloride and carbonation exposure was studied. Additionally, an evaluation of the microstructure was performed using optical microscopy on concrete thin sections. Test results revealed a substantial improvement of the resistance to chloride ion penetration into concrete containing blended cements. The resistance was higher for increased clinker replacement levels and increased with curing time. However, concrete made with blended cements exhibited higher depth of carbonation than the Portland cement concrete, except the Portland-fly ash cement with 14.3% of calcareous fly ash. The thin sections analysis confirmed the values of the carbonation depth obtained from the phenolphthalein test. Test results indicate the possible range of application for new cements containing calcareous fly ash.

Influence of Blended Cements with Calcareous Fly Ash on Chloride Ion Migration and Carbonation Resistance of Concrete for Durable Structures

PubMed Central

Glinicki, Michał A.; Jóźwiak-Niedźwiedzka, Daria; Gibas, Karolina; Dąbrowski, Mariusz

2016-01-01

The objective of this paper is to examine the possible use of new blended cements containing calcareous fly ash in structural concrete, potentially adequate for structural elements of nuclear power plants. The investigation included five new cements made with different contents of non-clinker constituents: calcareous fly ash, siliceous fly ash, ground granulated blastfurnace slag, and a reference cement—ordinary Portland cement. The influence of innovative cements on the resistance of concrete to chloride and carbonation exposure was studied. Additionally, an evaluation of the microstructure was performed using optical microscopy on concrete thin sections. Test results revealed a substantial improvement of the resistance to chloride ion penetration into concrete containing blended cements. The resistance was higher for increased clinker replacement levels and increased with curing time. However, concrete made with blended cements exhibited higher depth of carbonation than the Portland cement concrete, except the Portland-fly ash cement with 14.3% of calcareous fly ash. The thin sections analysis confirmed the values of the carbonation depth obtained from the phenolphthalein test. Test results indicate the possible range of application for new cements containing calcareous fly ash. PMID:28787821

Atmospheric fate and transport of fine volcanic ash: Does particle shape matter?

NASA Astrophysics Data System (ADS)

White, C. M.; Allard, M. P.; Klewicki, J.; Proussevitch, A. A.; Mulukutla, G.; Genareau, K.; Sahagian, D. L.

2013-12-01

Volcanic ash presents hazards to infrastructure, agriculture, and human and animal health. In particular, given the economic importance of intercontinental aviation, understanding how long ash is suspended in the atmosphere, and how far it is transported has taken on greater importance. Airborne ash abrades the exteriors of aircraft, enters modern jet engines and melts while coating interior engine parts causing damage and potential failure. The time fine ash stays in the atmosphere depends on its terminal velocity. Existing models of ash terminal velocities are based on smooth, quasi-spherical particles characterized by Stokes velocity. Ash particles, however, violate the various assumptions upon which Stokes flow and associated models are based. Ash particles are non-spherical and can have complex surface and internal structure. This suggests that particle shape may be one reason that models fail to accurately predict removal rates of fine particles from volcanic ash clouds. The present research seeks to better parameterize predictive models for ash particle terminal velocities, diffusivity, and dispersion in the atmospheric boundary layer. The fundamental hypothesis being tested is that particle shape irreducibly impacts the fate and transport properties of fine volcanic ash. Pilot studies, incorporating modeling and experiments, are being conducted to test this hypothesis. Specifically, a statistical model has been developed that can account for actual volcanic ash size distributions, complex ash particle geometry, and geometry variability. Experimental results are used to systematically validate and improve the model. The experiments are being conducted at the Flow Physics Facility (FPF) at UNH. Terminal velocities and dispersion properties of fine ash are characterized using still air drop experiments in an unconstrained open space using a homogenized mix of source particles. Dispersion and sedimentation dynamics are quantified using particle image velocimetry (PIV). Scanning Electron Microscopy (SEM) of ash particles collected in localized deposition areas is used to correlate the PIV results to particle shape. In addition, controlled wind tunnel experiments are used to determine particle fate and transport in a turbulent boundary layer for a mixed particle population. Collectively, these studies will provide an improved understanding of the effects of particle shape on sedimentation and dispersion, and foundational data for the predictive modeling of the fate and transport of fine ash particles suspended in the atmosphere.

Near Real Time Detection and Tracking of the EYJAFJÖLL (iceland) Ash Cloud by the RST (robust Satellite Technique) Approach

NASA Astrophysics Data System (ADS)

Tramutoli, V.; Filizzola, C.; Marchese, F.; Paciello, R.; Pergola, N.; Sannazzaro, F.

2010-12-01

Volcanic ash clouds, besides to be an environmental issue, represent a serious problem for air traffic and an important economic threat for aviation companies. During the recent volcanic crisis due to the April-May 2010 eruption of Eyjafjöll (Iceland), ash clouds became a real problem for common citizens as well: during the first days of the eruption thousands of flights were cancelled disrupting hundred of thousands of passengers. Satellite remote sensing confirmed to be a crucial tool for monitoring this kind of events, spreading for thousands of kilometres with a very rapid space-time dynamics. Especially weather satellites, thanks to their high temporal resolution, may furnish a fundamental contribution, providing frequently updated information. However, in this particular case ash cloud was accompanied by a sudden and significant emission of water vapour, due to the ice melting of Eyjafjallajökull glacier, making satellite ash detection and discrimination very hard, especially in the first few days of the eruption, exactly when accurate information were mostly required in order to support emergency management. Among the satellite-based techniques for near real-time detection and tracking of ash clouds, the RST (Robust Satellite Technique) approach, formerly named RAT - Robust AVHRR Technique, has been long since proposed, demonstrating high performances both in terms of reliability and sensitivity. In this paper, results achieved by using RST-based detection schemes, applied during the Eyjafjöll eruption were presented. MSG-SEVIRI (Meteosat Second Generation - Spinning Enhanced and Visible Infrared Imager) records, with a temporal sampling of 15 minutes, were used applying a standard as well as an advanced RST configuration, which includes the use of SO2 absorption band together with TIR and MIR channels. Main outcomes, limits and possible future improvements were also discussed.

Investigating waste rock, tailings, slag and coal ash clinker as adsorbents for heavy metals: Batch and column studies

NASA Astrophysics Data System (ADS)

Letina, D.; Letshwenyo, W. M.

2018-06-01

Wastewater from the mining industry is a concern because most of the time it contains heavy metals with concentrations above permissible levels, posing a threat to terrestrial and aquatic life. The study was conducted to evaluate the effectiveness of locally available waste materials (waste rock, tailings, coal ash clinker, and slag) generated by BCL (Ltd) mine, a copper and nickel mining and smelting company in Botswana, for removal of nickel and copper from the real mining wastewater. Batch adsorption studies were conducted to establish the adsorptive efficiency and kinetics of each media with respect to nickel and copper ions. The best media was further evaluated through fixed bed column studies at 24 and 48 h empty bed contact time. The results indicate that the percentage removal for coal ash clinker, waste rock, smelter slag and tailings was 98%, 15%, 3% and -3% with respect to copper ions, and 46%, 9%, 7% and 2% with respect to nickel ions for each media respectively. Coal ash clinker followed pseudo first order kinetic model and Langmuir isotherm model with respect to nickel ions indicating the dominance of physisorption and mono layer coverage respectively. The Langmuir separation factor (RL) was 0.37 suggesting favourable adsorption onto the media. Fixed bed column studies revealed that copper was completely retained in the bed at both 24 and 48 h contact times. In the case of nickel, removal efficiency ranged between 83% and 99% when contact time was 48 h and between 68% and 99% when the contact time was reduced to 24 h. Breakthrough was not reached after 19 bed volumes. It can be concluded that coal ash clinker is a better candidate for the removal of copper and nickel ions from mining wastewater.

Ground-based microwave radar and optical lidar signatures of volcanic ash plumes: models, observations and retrievals

NASA Astrophysics Data System (ADS)

Mereu, Luigi; Marzano, Frank; Mori, Saverio; Montopoli, Mario; Cimini, Domenico; Martucci, Giovanni

2013-04-01

The detection and quantitative retrieval of volcanic ash clouds is of significant interest due to its environmental, climatic and socio-economic effects. Real-time monitoring of such phenomena is crucial, also for the initialization of dispersion models. Satellite visible-infrared radiometric observations from geostationary platforms are usually exploited for long-range trajectory tracking and for measuring low level eruptions. Their imagery is available every 15-30 minutes and suffers from a relatively poor spatial resolution. Moreover, the field-of-view of geostationary radiometric measurements may be blocked by water and ice clouds at higher levels and their overall utility is reduced at night. Ground-based microwave radars may represent an important tool to detect and, to a certain extent, mitigate the hazard from the ash clouds. Ground-based weather radar systems can provide data for determining the ash volume, total mass and height of eruption clouds. Methodological studies have recently investigated the possibility of using ground-based single-polarization and dual-polarization radar system for the remote sensing of volcanic ash cloud. A microphysical characterization of volcanic ash was carried out in terms of dielectric properties, size distribution and terminal fall speed, assuming spherically-shaped particles. A prototype of volcanic ash radar retrieval (VARR) algorithm for single-polarization systems was proposed and applied to S-band and C-band weather radar data. The sensitivity of the ground-based radar measurements decreases as the ash cloud is farther so that for distances greater than about 50 kilometers fine ash might be not detected anymore by microwave radars. In this respect, radar observations can be complementary to satellite, lidar and aircraft observations. Active remote sensing retrieval from ground, in terms of detection, estimation and sensitivity, of volcanic ash plumes is not only dependent on the sensor specifications, but also on the range and ash cloud distribution. The minimum detectable signal can be increased, for a given system and ash plume scenario, by decreasing the observation range and increasing the operational frequency using a multi-sensor approach, but also exploiting possible polarimetric capabilities. In particular, multi-wavelengths lidars can be complementary systems useful to integrate radar-based ash particle measurement. This work, starting from the results of a previous study and from above mentioned issues, is aimed at quantitatively assessing the optimal choices for microwave and millimeter-wave radar systems with a dual-polarization capability for real-time ash cloud remote sensing to be used in combination with an optical lidar. The physical-electromagnetic model of ash particle distributions is systematically reviewed and extended to include non-spherical particle shapes, vesicular composition, silicate content and orientation phenomena. The radar and lidar scattering and absorption response is simulated and analyzed in terms of self-consistent polarimetric signatures for ash classification purposes and correlation with ash concentration and mean diameter for quantitative retrieval aims. A sensitivity analysis to ash concentration, as a function of sensor specifications, range and ash category, is carried out trying to assess the expected multi-sensor multi-spectral system performances and limitations. The multi-sensor multi-wavelength polarimetric model-based approach can be used within a particle classification and estimation scheme, based on the VARR Bayesian metrics. As an application, the ground-based observation of the Eyjafjallajökull volcanic ash plume on 15-16 May 2010, carried out at the Atmospheric Research Station at Mace Head, Carna (Ireland) with MIRA36 35-GHz Ka-Band Doppler cloud radar and CHM15K lidar/ceilometer at 1064-nm wavelength, has been considered. Results are discussed in terms of retrievals and intercomparison with other ground-based and satellite-based sensors.

A retrospective study on acute health effects due to volcanic ash exposure during the eruption of Mount Etna (Sicily) in 2002

PubMed Central

2013-01-01

Background Mount Etna, located in the eastern part of Sicily (Italy), is the highest and most active volcano in Europe. During the sustained eruption that occurred in October-November 2002 huge amounts of volcanic ash fell on a densely populated area south-east of Mount Etna in Catania province. The volcanic ash fall caused extensive damage to infrastructure utilities and distress in the exposed population. This retrospective study evaluates whether or not there was an association between ash fall and acute health effects in exposed local communities. Methods We collected the number and type of visits to the emergency department (ED) for diseases that could be related to volcanic ash exposure in public hospitals of the Province of Catania between October 20 and November 7, 2002. We compared the magnitude of differences in ED visits between the ash exposure period in 2002 and the same period of the previous year 2001. Results We observed a significant increase of ED visits for acute respiratory and cardiovascular diseases, and ocular disturbances during the ash exposure time period. Conclusions There was a positive association between exposure to volcanic ash from the 2002 eruption of Mount Etna and acute health effects in the Catania residents. This study documents the need for public health preparedness and response initiatives to protect nearby populations from exposure to ash fall from future eruptions of Mount Etna. PMID:23924394

Investigation of impurity confinement in lower hybrid wave heated plasma on EAST tokamak

NASA Astrophysics Data System (ADS)

Xu, Z.; Wu, Z. W.; Zhang, L.; Gao, W.; Ye, Y.; Chen, K. Y.; Yuan, Y.; Zhang, W.; Yang, X. D.; Chen, Y. J.; Zhang, P. F.; Huang, J.; Wu, C. R.; Morita, S.; Oishi, T.; Zhang, J. Z.; Duan, Y. M.; Zang, Q.; Ding, S. Y.; Liu, H. Q.; Chen, J. L.; Hu, L. Q.; Xu, G. S.; Guo, H. Y.; the EAST Team

2018-01-01

The transient perturbation method with metallic impurities such as iron (Fe, Z  =  26) and copper (Cu, Z  =  29) induced in plasma-material interaction (PMI) procedure is used to investigate the impurity confinement characters in lower hybrid wave (LHW) heated EAST sawtooth-free plasma. The dependence of metallic impurities confinement time on plasma parameters (e.g. plasma current, toroidal magnetic field, electron density and heating power) are investigated in ohmic and LHW heated plasma. It is shown that LHW heating plays an important role in the reduction of the impurity confinement time in L-mode discharges on EAST. The impurity confinement time scaling is given as 42IP0.32Bt0.2\\overline{n}e0.43Ptotal-0.4~ on EAST, which is close to the observed scaling on Tore Supra and JET. Furthermore, the LHW heated high-enhanced-recycling (HER) H-mode discharges with ~25 kHz edge coherent modes (ECM), which have lower impurity confinement time and higher energy confinement time, provide promising candidates for high performance and steady state operation on EAST.

Studies of fly ash using thermal analysis techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Hanxu; Shen, Xiang-Zhong; Sisk, B.

1996-12-31

Improved thermoanalytical methods have been developed that are capable of quantitative identification of various components of fly ash from a laboratory-scale fluidized bed combustion system. The thermogravimetric procedure developed can determine quantities of H{sub 2}O, Ca(OH){sub 2}, CaCO{sub 3}, CaSO{sub 4} and carbonaceous matter in fly ash with accuracy comparable to more time-consuming ASTM methods. This procedure is a modification of the Mikhail-Turcotte methods that can accurately analyze bed ash, with higher accuracy regarding the greater amount of carbonaceous matter in fly ash. In addition, in conjunction with FTIR and SEM/EDS analysis, the reduction mechanism of CaSO{sub 4} as CaSO{submore » 4} + 4H{sub 2} = CaS + 4H{sub 2}O has been confirmed in this study. This mechanism is important in analyzing and evaluating sulfur capture in fluidized-bed combustion systems.« less

Adsorption of 2,4-Dichlorophenoxyacetic Acid from an Aqueous Solution on Fly Ash.

PubMed

Kuśmierek, Krzysztof; Świątkowski, Andrzej

2016-03-01

The adsorption of 2,4-dichlorophenoxyacetic acid (2,4-D) on fly ash was studied. The effects of adsorbent dose, contact time, pH, ionic strength, and temperature on the adsorption were investigated. Adsorption kinetic data were analyzed using pseudo-first and pseudo-second order models, and results showed that adsorption kinetics were better represented by the pseudo-second order model. Adsorption isotherms of 2,4-D on fly ash were analyzed using the Freundlich and Langmuir models. Thermodynamic parameters (ΔG°, ΔH°, and ΔS°) indicated that the adsorption process was spontaneous and endothermic. The negative values of ΔG° and the positive value of ΔH° indicate the spontaneous nature of 2,4-D adsorption on fly ash, and that the adsorption process was endothermic. Results showed that fly ash is an efficient, low-cost adsorbent for removal of 2,4-D from water.

A robust method to forecast volcanic ash clouds

USGS Publications Warehouse

Denlinger, Roger P.; Pavolonis, Mike; Sieglaff, Justin

2012-01-01

Ash clouds emanating from volcanic eruption columns often form trails of ash extending thousands of kilometers through the Earth's atmosphere, disrupting air traffic and posing a significant hazard to air travel. To mitigate such hazards, the community charged with reducing flight risk must accurately assess risk of ash ingestion for any flight path and provide robust forecasts of volcanic ash dispersal. In response to this need, a number of different transport models have been developed for this purpose and applied to recent eruptions, providing a means to assess uncertainty in forecasts. Here we provide a framework for optimal forecasts and their uncertainties given any model and any observational data. This involves random sampling of the probability distributions of input (source) parameters to a transport model and iteratively running the model with different inputs, each time assessing the predictions that the model makes about ash dispersal by direct comparison with satellite data. The results of these comparisons are embodied in a likelihood function whose maximum corresponds to the minimum misfit between model output and observations. Bayes theorem is then used to determine a normalized posterior probability distribution and from that a forecast of future uncertainty in ash dispersal. The nature of ash clouds in heterogeneous wind fields creates a strong maximum likelihood estimate in which most of the probability is localized to narrow ranges of model source parameters. This property is used here to accelerate probability assessment, producing a method to rapidly generate a prediction of future ash concentrations and their distribution based upon assimilation of satellite data as well as model and data uncertainties. Applying this method to the recent eruption of Eyjafjallajökull in Iceland, we show that the 3 and 6 h forecasts of ash cloud location probability encompassed the location of observed satellite-determined ash cloud loads, providing an efficient means to assess all of the hazards associated with these ash clouds.

Optimization of isolation of cellulose from orange peel using sodium hydroxide and chelating agents.

PubMed

Bicu, Ioan; Mustata, Fanica

2013-10-15

Response surface methodology was used to optimize cellulose recovery from orange peel using sodium hydroxide (NaOH) as isolation reagent, and to minimize its ash content using ethylenediaminetetraacetic acid (EDTA) as chelating agent. The independent variables were NaOH charge, EDTA charge and cooking time. Other two constant parameters were cooking temperature (98 °C) and liquid-to-solid ratio (7.5). The dependent variables were cellulose yield and ash content. A second-order polynomial model was used for plotting response surfaces and for determining optimum cooking conditions. The analysis of coefficient values for independent variables in the regression equation showed that NaOH and EDTA charges were major factors influencing the cellulose yield and ash content, respectively. Optimum conditions were defined by: NaOH charge 38.2%, EDTA charge 9.56%, and cooking time 317 min. The predicted cellulose yield was 24.06% and ash content 0.69%. A good agreement between the experimental values and the predicted was observed. Copyright © 2013 Elsevier Ltd. All rights reserved.

Characterization of moderate ash-and-gas explosions at Santiaguito volcano, Guatemala, from infrasound waveform inversion and thermal infrared measurements

NASA Astrophysics Data System (ADS)

Angelis, S. De; Lamb, O. D.; Lamur, A.; Hornby, A. J.; von Aulock, F. W.; Chigna, G.; Lavallée, Y.; Rietbrock, A.

2016-06-01

The rapid discharge of gas and rock fragments during volcanic eruptions generates acoustic infrasound. Here we present results from the inversion of infrasound signals associated with small and moderate gas-and-ash explosions at Santiaguito volcano, Guatemala, to retrieve the time history of mass eruption rate at the vent. Acoustic waveform inversion is complemented by analyses of thermal infrared imagery to constrain the volume and rise dynamics of the eruption plume. Finally, we combine results from the two methods in order to assess the bulk density of the erupted mixture, constrain the timing of the transition from a momentum-driven jet to a buoyant plume, and to evaluate the relative volume fractions of ash and gas during the initial thrust phase. Our results demonstrate that eruptive plumes associated with small-to-moderate size explosions at Santiaguito only carry minor fractions of ash, suggesting that these events may not involve extensive magma fragmentation in the conduit.

Characterization of moderate ash-and-gas explosions at Santiaguito volcano, Guatemala, from infrasound waveform inversion and thermal infrared measurements.

PubMed

Angelis, S De; Lamb, O D; Lamur, A; Hornby, A J; von Aulock, F W; Chigna, G; Lavallée, Y; Rietbrock, A

2016-06-28

The rapid discharge of gas and rock fragments during volcanic eruptions generates acoustic infrasound. Here we present results from the inversion of infrasound signals associated with small and moderate gas-and-ash explosions at Santiaguito volcano, Guatemala, to retrieve the time history of mass eruption rate at the vent. Acoustic waveform inversion is complemented by analyses of thermal infrared imagery to constrain the volume and rise dynamics of the eruption plume. Finally, we combine results from the two methods in order to assess the bulk density of the erupted mixture, constrain the timing of the transition from a momentum-driven jet to a buoyant plume, and to evaluate the relative volume fractions of ash and gas during the initial thrust phase. Our results demonstrate that eruptive plumes associated with small-to-moderate size explosions at Santiaguito only carry minor fractions of ash, suggesting that these events may not involve extensive magma fragmentation in the conduit.

Fly ash zeolite catalyst support for Fischer-Tropsch synthesis

NASA Astrophysics Data System (ADS)

Campen, Adam

This dissertation research aimed at evaluating a fly ash zeolite (FAZ) catalyst support for use in heterogeneous catalytic processes. Gas phase Fischer-Tropsch Synthesis (FTS) over a fixed-bed of the prepared catalyst/FAZ support was identified as an appropriate process for evaluation, by comparison with commercial catalyst supports (silica, alumina, and 13X). Fly ash, obtained from the Wabash River Generating Station, was first characterized using XRD, SEM/EDS, particle size, and nitrogen sorption techniques. Then, a parametric study of a two-step alkali fusion/hydrothermal treatment process for converting fly ash to zeolite frameworks was performed by varying the alkali fusion agent, agent:flyash ratio, fusion temperature, fused ash/water solution, aging time, and crystallization time. The optimal conditions for each were determined to be NaOH, 1.4 g NaOH: 1 g fly ash, 550 °C, 200 g/L, 12 hours, and 48 hours. This robust process was applied to the fly ash to obtain a faujasitic zeolite structure with increased crystallinity (40 %) and surface area (434 m2/g). Following the modification of fly ash to FAZ, ion exchange of H+ for Na+ and cobalt incipient wetness impregnation were used to prepare a FTS catalyst. FTS was performed on the catalysts at 250--300 °C, 300 psi, and with a syngas ratio H2:CO = 2. The HFAZ catalyst support loaded with 11 wt% cobalt resulted in a 75 % carbon selectivity for C5 -- C18 hydrocarbons, while methane and carbon dioxide were limited to 13 and 1 %, respectively. Catalyst characterization was performed by XRD, N2 sorption, TPR, and oxygen pulse titration to provide insight to the behavior of each catalyst. Overall, the HFAZ compared well with silica and 13X supports, and far exceeded the performance of the alumina support under the tested conditions. The successful completion of this research could add value to an underutilized waste product of coal combustion, in the form of catalyst supports in heterogeneous catalytic processes.

Volcanic ash modeling with the NMMB-MONARCH-ASH model: quantification of offline modeling errors

NASA Astrophysics Data System (ADS)

Marti, Alejandro; Folch, Arnau

2018-03-01

Volcanic ash modeling systems are used to simulate the atmospheric dispersion of volcanic ash and to generate forecasts that quantify the impacts from volcanic eruptions on infrastructures, air quality, aviation, and climate. The efficiency of response and mitigation actions is directly associated with the accuracy of the volcanic ash cloud detection and modeling systems. Operational forecasts build on offline coupled modeling systems in which meteorological variables are updated at the specified coupling intervals. Despite the concerns from other communities regarding the accuracy of this strategy, the quantification of the systematic errors and shortcomings associated with the offline modeling systems has received no attention. This paper employs the NMMB-MONARCH-ASH model to quantify these errors by employing different quantitative and categorical evaluation scores. The skills of the offline coupling strategy are compared against those from an online forecast considered to be the best estimate of the true outcome. Case studies are considered for a synthetic eruption with constant eruption source parameters and for two historical events, which suitably illustrate the severe aviation disruptive effects of European (2010 Eyjafjallajökull) and South American (2011 Cordón Caulle) volcanic eruptions. Evaluation scores indicate that systematic errors due to the offline modeling are of the same order of magnitude as those associated with the source term uncertainties. In particular, traditional offline forecasts employed in operational model setups can result in significant uncertainties, failing to reproduce, in the worst cases, up to 45-70 % of the ash cloud of an online forecast. These inconsistencies are anticipated to be even more relevant in scenarios in which the meteorological conditions change rapidly in time. The outcome of this paper encourages operational groups responsible for real-time advisories for aviation to consider employing computationally efficient online dispersal models.

Computation of probabilistic hazard maps and source parameter estimation for volcanic ash transport and dispersion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madankan, R.; Pouget, S.; Singla, P., E-mail: psingla@buffalo.edu

Volcanic ash advisory centers are charged with forecasting the movement of volcanic ash plumes, for aviation, health and safety preparation. Deterministic mathematical equations model the advection and dispersion of these plumes. However initial plume conditions – height, profile of particle location, volcanic vent parameters – are known only approximately at best, and other features of the governing system such as the windfield are stochastic. These uncertainties make forecasting plume motion difficult. As a result of these uncertainties, ash advisories based on a deterministic approach tend to be conservative, and many times over/under estimate the extent of a plume. This papermore » presents an end-to-end framework for generating a probabilistic approach to ash plume forecasting. This framework uses an ensemble of solutions, guided by Conjugate Unscented Transform (CUT) method for evaluating expectation integrals. This ensemble is used to construct a polynomial chaos expansion that can be sampled cheaply, to provide a probabilistic model forecast. The CUT method is then combined with a minimum variance condition, to provide a full posterior pdf of the uncertain source parameters, based on observed satellite imagery. The April 2010 eruption of the Eyjafjallajökull volcano in Iceland is employed as a test example. The puff advection/dispersion model is used to hindcast the motion of the ash plume through time, concentrating on the period 14–16 April 2010. Variability in the height and particle loading of that eruption is introduced through a volcano column model called bent. Output uncertainty due to the assumed uncertain input parameter probability distributions, and a probabilistic spatial-temporal estimate of ash presence are computed.« less

Impact of super-distal ash fallout on tropical hydrology and landscape: a case study from the YTT deposits of the Perak river, Malaysia

NASA Astrophysics Data System (ADS)

Gatti, E.; Saidin, M.; Gibbard, P.; Oppenheimer, C.

2011-12-01

The Younger Toba Tuff eruption, approximately 73 ka ago, is the largest known for the Quaternary and its climate, environmental and human consequences are keenly debated (Oppenheimer, 2011).While the distribution (Rose and Chesner, 1987; Rose and Chesner, 1990; Chesner et al., 1991; Schulz et al., 2002; Von Rad et al., 2002) , geochemical properties (Shane et al., 1995; Westgate et al., 1998) and volcanic significance (Rampino and Self, 1982; Rampino and Self, 1993; Rampino and Ambrose, 2000; Oppenheimer, 2002; Mason et al., 2004)of the YTT have been widely studied, few attention has been given to the significance of the distal volcanic ash deposits within their receiving basin context. Although several studies exist on the impact of pyroclastic flows on proximal rivers and lakes (Collins and Dunne, 1986; Thompson et al., 1986; Hayes et al., 2002; Németh and Cronin, 2007), only few address the issues of the dynamic of preservation of super-distal fine ash deposits in rivers (also due to the lack of direct data on super-eruptions). It has also been demonstrated that models of the styles and timing of distal volcanoclastic re-sedimentation are more complicated than those developed for proximal settings of stratovolcanoes (Kataoka et al., 2009). We present an analysis of the taphonomy (intended as accumulation and preservation) of distal volcanic ash in fluvial and lacustrian contexts in newly discovered Toungest Toba Tuff sites in the Lenggong valley, western Peninsular Malaysia. The paper aims to characterise the nature of distal tephras in fluvial environments towards a stratigraphic distinction between primary ash and secondary ash, characterisation of the pre-ash fall receiving environment in term of fluvial dynamic and landscape morphology, and assessment of the time of recovery.

Temporal changes in soil water repellency after a forest fire in a Mediterranean calcareous soil: Influence of ash and different vegetation type.

PubMed

Jiménez-Pinilla, P; Lozano, E; Mataix-Solera, J; Arcenegui, V; Jordán, A; Zavala, L M

2016-12-01

Forest fires usually modify soil water repellency (SWR), and its persistence and intensity show a high variability both in space and time. This research studies the evolution of SWR in a Mediterranean calcareous soil affected by a forest fire, which occurred in Gorga (SE Spain) in July 2011, comparing the effect of the main vegetation cover between pine (Pinus halepensis) and shrubs species (Quercus coccifera, Rosmarinus officinalis, Cistus albidus, Erica arborea and Brachypodium retusum) and the relationship with soil moisture content (SMC). Also the study analyzed the effect of ash on SWR dynamics under field conditions. Six plots were established on the fire-affected area and the unburned-control-adjacent area to monitoring SWR with the water drop penetration time (WDPT) test, SMC through moist sensors (5cm depth) and three different ash treatments: ash presence, ash absence and incorporation of ash into the soil. An immediate increase of SWR was observed in the fire-affected area, mainly in pine plots. SWR changes in control (unburned) plots were quite similar between different types of vegetation influence, despite higher SWR values being observed on pine plots during the study period. A noticeable decrease of SWR was observed during the first months after fire in the affected areas, especially after the first rainy period, both in pine and shrubs plots. SWR increase was registered in all plots, and the highest levels were in March 2012 in burned pine plots. SWR decrease was higher in plots where ash was removed. Fire-affected soils became wettable 1year and a half after the fire. Copyright © 2015 Elsevier B.V. All rights reserved.

Controlling risks of P water pollution by sorption on soils, pyritic material, granitic material, and different by-products: effects of pH and incubation time.

PubMed

Romar-Gasalla, Aurora; Nóvoa-Muñoz, Juan Carlos; Arias-Estévez, Manuel; Fernández-Sanjurjo, María J; Álvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

2018-05-13

Batch experiments were used to test P sorbent potential of soil samples, pyritic and granitic materials, mussel shell, mussel shell ash, sawdust, and slate waste fines for different pH and incubation times. Maximum P sorption varied in a wide range of pH: < 4 for pyritic material, 4-6 for forest soil, > 5 for slate fines, > 6 for shell ash, and pH 6-8 for mussel shell. P sorption was rapid (< 24 h) for forest soil, shell ash, pyritic material, and fine shell. On the opposite side, it was clearly slower for vineyard soil, granitic material, slate fines, pine sawdust, and coarse shell, with increased P sorption even 1 month later. For any incubation time, P sorption was > 90% in shell ash, whereas forest soil, pyritic material, and fine shell showed sorption rates approaching 100% within 24 h of incubation. These results could be useful to manage and/or recycle the sorbents tested when focusing on P immobilization or removal, in circumstances where pH changes and where contact time may vary from hours to days, thus aiding to diminish P pollution and subsequent eutrophication risks, promoting conservation and sustainability.

Biomass fly ash incorporation in cement based materials =

NASA Astrophysics Data System (ADS)

Rajamma, Rejini

In recent years, pressures on global environment and energy security have led to an increasing demand on renewable energy sources, and diversification of Europe's energy supply. Among these resources the biomass could exert an important role, since it is considered a renewable and CO2 neutral energy resource once the consumption rate is lower than the growth rate, and can potentially provide energy for heat, power and transports from the same installation. Currently, most of the biomass ash produced in industrial plants is either disposed of in landfill or recycled on agricultural fields or forest, and most times this goes on without any form of control. However, considering that the disposal cost of biomass ashes are raising, and that biomass ash volumes are increasing worldwide, a sustainable ash management has to be established. The main objective of the present study is the effect of biomass fly ashes in cement mortars and concretes in order to be used as a supplementary cementitious material. The wastes analyzed in the study were collected from the fluidized bed boilers and grate boilers available in the thermal power plants and paper pulp plants situated in Portugal. The physical as well as chemical characterisations of the biomass fly ashes were investigated. The cement was replaced by the biomass fly ashes in 10, 20 and 30% (weight %) in order to investigate the fresh properties as well as the hardened properties of biomass fly ash incorporated cement mortar and concrete formulations. Expansion reactions such as alkali silica reaction (ASR), sulphate attack (external and internal) were conducted in order to check the durability of the biomass fly ash incorporated cement mortars and concretes. Alternative applications such as incorporation in lime mortars and alkali activation of the biomass fly ashes were also attempted. The biomass fly ash particles were irregular in shape and fine in nature. The chemical characterization revealed that the biomass fly ashes were similar to a class C fly ash. The mortar results showed a good scope for biomass fly ashes as supplementary cementitious materials in lower dosages (<20%). The poor workability, concerns about the organic content, alkalis, chlorides and sulphates stand as the reasons for preventing the use of biomass fly ash in high content in the cement mortars. The results obtained from the durability tests have shown a clear reduction in expansion for the biomass fly ash mortars/concretes and the binder blend made with biomass fly ash (20%) and metakaolin (10%) inhibited the ASR reaction effectively. The biomass fly ash incorporation in lime mortars did not improve the mortar properties significantly though the carbonation was enhanced in the 15-20% incorporation. The biomass fly ash metakaolin blend worked well in the alkali activated complex binder application also. Portland cement free binders (with 30-40 MPa compressive strength) were obtained on the alkali activation of biomass fly ashes (60-80%) blended with metakaolin (20-40%).

Field Investigations of the July 2015 Pyroclastic Density Current Deposits of Volcán de Colima, Mexico

NASA Astrophysics Data System (ADS)

Atlas, Z. D.; Macorps, E.; Charbonnier, S. J.; Varley, N. R.

2016-12-01

Small-volume pyroclastic density currents (PDCs) occur relatively frequently and pose severe threats to surrounding populations and infrastructures at active explosive volcanoes. They are characterized by short duration and complex multiphase flow dynamics due to time and space variability in their properties, which include amongst others, particle concentration, granulometry, componentry, bulk rheology and velocity. Field investigations of the deposits emplaced by small-volume concentrated PDCs aim to improve our understanding of the transport and depositional processes of these flows: time and space variations in flow dynamics within a PDC moving downslope will reflect on the distribution, grainsize and component characteristics of its deposits. Our study focuses on the recent events of July 10th and 11th, 2015 at Volcán de Colima (Mexico) where the collapse of the recent lava dome complex and a portion of the southern crater rim led to the emplacement of successive pulses of small-volume concentrated PDCs on the southern flank, along the Montegrande and San Antonio ravines. A 3-dimensional field analysis of the PDCs' deposit architecture, total grain size distribution and component properties together with a geomorphic analysis of the affected ravines provide new insights on the lateral and vertical variations of flow dynamics for some of these small-volume concentrated PDCs. Preliminary results reveal three stratigraphic units with massive block, lapilli, ash facies within the valley confined and concentrated overbank deposits with increasing content in fines with distance from the summit, suggesting an increase in fragmentation processes within the PDCs. The middle unit is characterized by a finer grainsize, a higher accidental lithic content and a lower free crystal content. Moreover, direct correlations are found between rapid changes in channel morphology and generation of overbank (unconfined) flows that escaped valley confines, which could provide the basis for defining hazard zonations of key areas at risk from future eruptions at Colima.

Effect of Na2SiO3/NaOH on mechanical properties and microstructure of geopolymer mortar using fly ash and rice husk ash as precursor

NASA Astrophysics Data System (ADS)

Saloma, Hanafiah, Elysandi, Debby Orjina; Meykan, Della Garnesia

2017-11-01

Geopolymer concrete is an eco-friendly concrete that can reduce carbon emissions on the earth surface because it used industrial waste material such as fly ash, rice husk ash, bagasse ash, and palm oil fuel. Geopolymer is semi-crystalline amorphous materials which has irregular chemical bonds structure. The material is produced by geosynthesis of aluminosilicates and alkali-silicates which produce the Si-O-Al polymer structure. This research used the ratio of fly ash and rice husk ash as precursors e.g. 100:0, 75:25, 50:50, and 25:75. NaOH solutions of 14 M and Na2SiO3 solutions with the variation e.g. 2.5, 2.75, 3.00, and 3.25 were used as activators on mortar geopolymer mixture. The tests of fresh mortar were slump flow and setting time. The optimum compressive strength is 68.36 MPa for 28 days resulted from mixture using 100% fly ash and Na2SiO3 and NaOH with ratio 2.75. The largest value of slump flow test resulted from mixture using Na2SiO3 and NaOH with ratio 2.50 is 17.25 cm. Based on SEM test results, mortar geopolymer microstructure with mixture RHA 0% has less pores and denser CSH structure.

APhoRISM FP7 project: the Multi-platform volcanic Ash Cloud Estimation (MACE) infrastructure

NASA Astrophysics Data System (ADS)

Merucci, Luca; Corradini, Stefano; Bignami, Christian; Stramondo, Salvatore

2014-05-01

APHORISM is an FP7 project that aims to develop innovative products to support the management and mitigation of the volcanic and the seismic crisis. Satellite and ground measurements will be managed in a novel manner to provide new and improved products in terms of accuracy and quality of information. The Multi-platform volcanic Ash Cloud Estimation (MACE) infrastructure will exploit the complementarity between geostationary, and polar satellite sensors and ground measurements to improve the ash detection and retrieval and to fully characterize the volcanic ash clouds from source to the atmosphere. The basic idea behind the proposed method consists to manage in a novel manner, the volcanic ash retrievals at the space-time scale of typical geostationary observations using both the polar satellite estimations and in-situ measurements. The typical ash thermal infrared (TIR) retrieval will be integrated by using a wider spectral range from visible (VIS) to microwave (MW) and the ash detection will be extended also in case of cloudy atmosphere or steam plumes. All the MACE ash products will be tested on three recent eruptions representative of different eruption styles in different clear or cloudy atmospheric conditions: Eyjafjallajokull (Iceland) 2010, Grimsvotn (Iceland) 2011 and Etna (Italy) 2011-2012. The MACE infrastructure will be suitable to be implemented in the next generation of ESA Sentinels satellite missions.

Wildland fire ash: Production, composition and eco-hydro-geomorphic effects

USGS Publications Warehouse

Bodi, Merche B.; Martin, Deborah; Balfour, Victoria N.; Santin, Cristina; Doerr, Stefan H.; Pereira, Paulo; Cerda, Artemi; Mataix-Solera, Jorge

2014-01-01

Fire transforms fuels (i.e. biomass, necromass, soil organic matter) into materials with different chemical and physical properties. One of these materials is ash, which is the particulate residue remaining or deposited on the ground that consists of mineral materials and charred organic components. The quantity and characteristics of ash produced during a wildland fire depend mainly on (1) the total burned fuel (i.e. fuel load), (2) fuel type and (3) its combustion completeness. For a given fuel load and type, a higher combustion completeness will reduce the ash organic carbon content, increasing the relative mineral content, and hence reducing total mass of ash produced. The homogeneity and thickness of the ash layer can vary substantially in space and time and reported average thicknesses range from close to 0 to 50 mm. Ash is a highly mobile material that, after its deposition, may be incorporated into the soil profile, redistributed or removed from a burned site within days or weeks by wind and water erosion to surface depressions, footslopes, streams, lakes, reservoirs and, potentially, into marine deposits.Research on the composition, properties and effects of ash on the burned ecosystem has been conducted on material collected in the field after wildland and prescribed fires as well as on material produced in the laboratory. At low combustion completeness (typically T < 450 °C), ash is organic-rich, with organic carbon as the main component. At high combustion completeness (T > 450 °C), most organic carbon is volatized and the remaining mineral ash has elevated pH when in solution. It is composed mainly of calcium, magnesium, sodium, potassium, silicon and phosphorous in the form of inorganic carbonates, whereas at T > 580 °C the most common forms are oxides. Ash produced under lower combustion completeness is usually darker, coarser, and less dense and has a higher saturated hydraulic conductivity than ash with higher combustion completeness, although physical reactions with CO2 and when moistened produce further changes in ash characteristics.As a new material present after a wildland fire, ash can have profound effects on ecosystems. It affects biogeochemical cycles, including the C cycle, not only within the burned area, but also globally. Ash incorporated into the soil increases temporarily soil pH and nutrient pools and changes physical properties such as albedo, soil texture and hydraulic properties including water repellency. Ash modifies soil hydrologic behavior by creating a two-layer system: the soil and the ash layer, which can function in different ways depending on (1) ash depth and type, (2) soil type and (3) rainfall characteristics. Key parameters are the ash's water holding capacity, hydraulic conductivity and its potential to clog soil pores. Runoff from burned areas carries soluble nutrients contained in ash, which can lead to problems for potable water supplies. Ash deposition also stimulates soil microbial activity and vegetation growth.Further work is needed to (1) standardize methods for investigating ash and its effects on the ecosystem, (2) characterize ash properties for specific ecosystems and wildland fire types, (3) determine the effects of ash on human and ecosystem health, especially when transported by wind or water, (4) investigate ash's controls on water and soil losses at slope and catchment scales, (5) examine its role in the C cycle, and (6) study its redistribution and fate in the environment.

The Grainsize Characteristics of Coignimbrite Deposits

NASA Astrophysics Data System (ADS)

Engwell, Samantha; Eychenne, Julia

2015-04-01

Due to their long atmospheric residence time, identifying the source and understanding the dispersion processes of fine-grained ash is of great importance when considering volcanic hazard and risk. An exceptionally efficient mechanism to supply large volumes of fine-grained ash to the stratosphere is the formation of co-ignimbrite plumes. Such plumes form as air is entrained at the top of propagating pyroclastic density currents, allowing a neutrally buoyant package of gas and ash to loft to high altitudes, consequently dispersing over large areas. The study of ash deposits on land and in deep sea cores has demonstrated that such events have played a major role during ignimbrite-forming eruptions, including the Tambora 1815, the Minoan (Santorini), the Campanian Ignimbrite, and the Younger Toba Tuff eruptions, as well as during more recent, pyroclastic flow-forming, intermediate sized eruptions (Vulcanian to Plinian in style), e.g. Mount St. Helens 1980, Fugen-dake (Unzen) 1991, Pinatubo 1991, Montserrat 1997 and Tungurahua 2006 eruptions. Published, as well as new results from the study of co-ignimbrite deposits, show that co-ignimbrite plumes can rise to high altitudes into the atmosphere (the co-ignimbrite plumes from the May 18, 1980 Mount St Helens blast and the Campanian Ignimbrite eruptions reached 30 - 35 km a.s.l,), potentially distribute enormous volumes of ash (the 75 ka Toba eruption and the Minoan eruption of Santorini settled >800 km3 and >25 km3 of co-ignimbrite ash, respectively), and contribute much of the ash to very large (60±6 vol% of the Campanian fallout deposit 130 to 900 km from vent), as well as intermediate size (up to 58 wt% and 52 wt% in the 2006 Tungurahua and May 18, 1980 Mount St. Helens fallout deposits, respectively) explosive eruptions. Comparison of new data with those from the published record shows that co-ignimbrite deposits are strikingly similar, regardless of eruption conditions, and have distinct grain size characteristics. The deposits are very fine grained (< 100 microns), have unimodal grain size distributions skewed towards the fines, and are more poorly sorted in medial to distal areas than tephra fall deposits from vent-derived plumes at the same distance. Deposits from a single eruption show constant grain size over hundreds to thousands of kilometres, except for a slight coarsening close to source in some cases. In intermediate size eruptions, co-ignimbrite ash often settles synchronously to vent-derived tephra, leading to bimodal grain size fallout deposits. These observations highlight the propensity of the ash to remain in the atmosphere for extended periods of time, and pose important questions regarding how the ash is deposited, and especially the role of aggregation. The uniformity of co-ignimbrite ash means that, with regards to real-time dispersion modelling during an eruption, few assumptions are required for the initial grain size, however depositional assumptions utilised when modelling vent-derived plume dispersion, may not be able to accurately reproduce co-ignimbrite depositional patterns.

Fire severity effects on ash extractable Total Phosphorous

NASA Astrophysics Data System (ADS)

Pereira, Paulo; Úbeda, Xavier; Martin, Deborah

2010-05-01

Phosphorous (P) is a crucial element to plant nutrition and limits vegetal production. The amounts of P in soil are lower and great part of this nutrient is absorbed or precipitated. It is well known that fire has important implications on P cycle, that can be lost throughout volatilization, evacuated with the smoke, but also more available to transport after organic matter mineralization imposed by the fire. The release of P depends on ash pH and their chemical and physical characteristics. Fire temperatures impose different severities, according to the specie affected and contact time. Fire severity is often evaluated by ash colour and this is a low-cost and excellent methodology to assess the fire effects on ecosystems. The aim of this work is study the ash properties physical and chemical properties on ash extractable Total Phosphorous (TP), collected in three wildfires, occured in Portugal, (named, (1) Quinta do Conde, (2) Quinta da Areia and (3) Casal do Sapo) composed mainly by Quercus suber and Pinus pinaster trees. The ash colour was assessed using the Munsell color chart. From all three plots we analyzed a total of 102 ash samples and we identified 5 different ash colours, ordered in an increasing order of severity, Very Dark Brown, Black, Dark Grey, Very Dark Grey and Light Grey. In order to observe significant differences between extractable TP and ash colours, we applied an ANOVA One Way test, and considered the differences significant at a p<0.05. The results showed that significant differences in the extractable TP among the different ash colours. Hence, to identify specific differences between each ash colour, we applied a post-hoc Fisher LSD test, significant at a p<0.05. The results obtained showed significant differences between the extractable TP from Very dark Brown and Black ash, produced at lower severities, in relation to Dark Grey, Very Dark Grey and Light Grey ash, generated at higher severities. The means of the first group were higher than the observed in the second one. This indicates that ash produced lower temperatures release in solution higher amounts of TP. These divergences occur due temperature of combustion, affected specie, ash pH values and CaCO3 content, which affects the quantity of this element in solution. Discussions about these effects will be accurate in the communication.

Simulated Impacts of Emerald Ash Borer on Throughfall and Stemflow Inputs of Water and Nitrogen in Black Ash Wetlands in Northern Michigan

NASA Astrophysics Data System (ADS)

Pypker, T. G.; Davis, J.; Van Grinsven, M. J.; Bolton, N. W.; Shannon, J.; Kolka, R. K.; Nelson, J.; Wagenbrenner, J. W.

2014-12-01

Emerald ash borer (Agrilus planipennis Fairmaire (EAB)) is an invasive insect that effectively kills ash trees (genus: Fraxinus) greater than 2.5 cm in diameter, resulting in near-complete stand mortality within 3-4 years. Black ash wetlands occupy approximately 270,000 ha in Michigan, and have 40 to 90% of the basal area occupied by black ash (F. nigra Marshall); hence the loss of black ash may result in dramatic changes in the canopy hydrology and nutrient deposition. We assessed the impact of a simulated EAB invasion on throughfall and stemflow quantity and nitrogen (N) content in 9 uninfected black ash wetlands located in the Upper Peninsula of Michigan. Within the 9 stands, 3 stands were left untreated ('Control'), 3 stands had all the black ash trees manually girdled ('Girdled') and 3 had all the black ash trees felled by chainsaw ('Clearcut'). We measured the quantity and inorganic-N content of throughfall using an array of randomly placed collectors (n = 16 per site). Stemflow was monitored at 2 sites (n = 12 trees) on the 3 most common tree species (black ash, yellow birch (Betula alleghaniensis Britt.) and red maple (Acer rubra L.)). Preliminary results indicate that relative to the Control, average monthly throughfall was 25% and 1% greater in the Clearcut and Girdled sites, respectively. While the loss of the ash trees resulted in greater throughfall inputs in the Clearcut sites, water table heights did not significantly change as a result of the treatments. Stemflow from live black ash trees was lower than from the yellow birch and red maple trees. As a result, we predict stemflow will increase over time as species with smoother bark and less upright branching begin replacing the black ash. Hence, the change in tree species may result in a greater concentration of inorganic-N inputs to the base of the trees, thereby altering the distribution of inorganic-N inputs into the wetland. Our preliminary results show no significant change in the total inorganic-N deposition via throughfall. Despite the severity of the disturbance that resulted from the simulated EAB infestation, preliminary results suggest that that these wetlands may show some short-term resiliency to the impacts of ash mortality, resulting in relatively unchanged hydrologic and nutrient deposition regimes.

The impact of the characteristics of volcanic ash on forecasting.

NASA Astrophysics Data System (ADS)

Beckett, Frances; Hort, Matthew; Millington, Sarah; Stevenson, John; Witham, Claire

2013-04-01

The eruption of Eyjafjallajökull during April - May 2010 and Grímsvötn in May 2011, Iceland, caused the widespread dispersion of volcanic ash across the NE Atlantic, and ultimately into UK and European airspace. This resulted in thousands of flights to and from affected countries across Europe to be cancelled. The Met Office, UK, is the home of the London VAAC, a Volcanic Ash Advisory Centre, and as such is responsible for providing reports and forecasts for the movement of volcanic ash clouds covering the UK, Iceland and the north-eastern part of the North Atlantic ocean. To forecast the dispersion of volcanic ash requires that the sedimentation of ash particles through the atmosphere is effectively modelled. The settling velocity of an ash particle is a function of its size, shape and density, plus the density and viscosity of the air through which it is falling. We consider the importance of characterising the physical properties of ash when modelling the long range dispersion of ash particles through the atmosphere. Using the Reynolds number dependent scheme employed by NAME, the Lagrangian particle model used operationally by the Met Office, we calculate the settling velocity and thus the maximum travel distance of an ash particle through an idealised atmosphere as a function of its size, shape and density. The results are compared to measured particle sizes from deposits across Europe following the eruption of Eyjafjallajökull in 2010. Further, the particle size distribution (PSD) of ash in a volcanic cloud with time is modelled using NAME: the particle density distribution and particle shape factor are varied and the modelled PSD compared to the PSD measured in the ash cloud during the eruption of Eyjafjallajökull in 2010 by the FAAM research aircraft. The influence of the weather on PSD is also considered by comparing model output using an idealised atmosphere to output using NWP driven meteorological fields. We discuss the sensitivity of forecasts of the dispersion of volcanic ash to the representation of particle characteristics in NAME, the importance of representing the weather in ash fall models, and the implications of these results for the operational forecasting of volcanic ash dispersion at the London VAAC.

Reflectance-difference spectroscopy of GaAs crystal growth by OMCVD

NASA Astrophysics Data System (ADS)

Colas, Etienne G.; Aspnes, David E.; Bhat, Rajaram J.; Studna, A. A.; Koza, M. A.; Keramidas, Vassilis G.

1990-02-01

This paper summarizes results of our investigations of growth on (001) and (110) GaAs by atmospheric-pressure organometallic chemical vapor deposition (OMCVD). We follow evolutions of surface species to a sensitivity of 0.01 monolayer (ML) on a time scale of 0.1 s under alternating flows of trimethylgallium (TMG) and arsine (AsH3) as functions of partial pressure, sample temperature, and surface orienta-tion. The reaction of TMG with an AsH3-saturated (001) surface is rate-limited by com-petition between desorption and decomposition of TMG molecules chemisorbed to surface lattice sites via an excluded-volume mechanism, while the reaction of AsH3 with the TMG-saturated (001) surface is essentially instantaneous. In contrast, TMG reacts essentially instantaneously with the AsH3 -saturated (110) surface while the AsH3 reaction with the TMG-saturated (110) surface is the rate-limiting step. However, the latter rate is not intrinsic to the AsH3-surface reaction but appears to be determined by desorption of adsorbed species that block active sites.

Effectiveness of differing trap types for the detection of emerald ash borer (Coleoptera: Buprestidae).

PubMed

Marshall, Jordan M; Storer, Andrew J; Fraser, Ivich; Beachy, Jessica A; Mastro, Victor C

2009-08-01

The early detection of populations of a forest pest is important to begin initial control efforts, minimizing the risk of further spread and impact. Emerald ash borer (Agrilus planipennis Fairmaire) is an introduced pestiferous insect of ash (Fraxinus spp. L.) in North America. The effectiveness of trapping techniques, including girdled trap trees with sticky bands and purple prism traps, was tested in areas with low- and high-density populations of emerald ash borer. At both densities, large girdled trap trees (>30 cm diameter at breast height [dbh], 1.37 m in height) captured a higher rate of adult beetles per day than smaller trees. However, the odds of detecting emerald ash borer increased as the dbh of the tree increased by 1 cm for trap trees 15-25 cm dbh. Ash species used for the traps differed in the number of larvae per cubic centimeter of phloem. Emerald ash borer larvae were more likely to be detected below, compared with above, the crown base of the trap tree. While larval densities within a trap tree were related to the species of ash, adult capture rates were not. These results provide support for focusing state and regional detection programs on the detection of emerald ash borer adults. If bark peeling for larvae is incorporated into these programs, peeling efforts focused below the crown base may increase likelihood of identifying new infestations while reducing labor costs. Associating traps with larger trees ( approximately 25 cm dbh) may increase the odds of detecting low-density populations of emerald ash borer, possibly reducing the time between infestation establishment and implementing management strategies.

Does simulated acid rain increase the leaching of cadmium from wood ash to toxic levels to coniferous forest humus microbes?

PubMed

Perkiömäki, Jonna; Fritze, Hannu

2003-05-01

Abstract Wood ash contains Cd in concentrations not permitted for fertilization use in agriculture (>3 mg kg(-1)). It has been shown that spiking ash with Cd to concentrations of 1000 mg kg(-1) induced no further changes in humus microbial activity and community structure as ash alone. To accelerate the weathering process and thus to liberate the spiked Cd from the ash, three treatments - wood ash (A), Cd spiked wood ash (ACd, 1000 mg Cd kg(-1) ash), both applied at a fertilization rate of 5000 kg ha(-1), together with a control (C) - were performed in microcosms and incubated in field condition under two types of irrigation - water and simulated acid rain. During the incubation period of one growing season the simulated acid rain plots received a sulfur load of 3.64 g S m(-2), which was 15 times more than the S deposition on the water irrigated plots. The treatments resulted in a mean Cd increase of the humus from 0.23 mg kg(-1) of the C treatment to 0.52 and 39.5 mg kg(-1) of the A and ACd treatments, respectively. The irrigation had no further effect on the result. The microbial activity, measured as soil basal respiration, and the microbial community structure, measured as humus phospholipid fatty acid and 16S and 18S polymerase chain reaction/denaturing gradient gel electrophoresis patterns, changed only due to the ash (A and ACd treatments) fertilization irrespective of the irrigation. The bacterial biosensor, emitting light in the presence of bioavailable Cd, did not react to any of the treatments. This result shows that Cd in ash was not leached into the humus due to increased deposition of acidified rain.

Ignition threshold for non-Maxwellian plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hay, Michael J., E-mail: hay@princeton.edu; Fisch, Nathaniel J.; Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543

2015-11-15

An optically thin p-{sup 11}B plasma loses more energy to bremsstrahlung than it gains from fusion reactions, unless the ion temperature can be elevated above the electron temperature. In thermal plasmas, the temperature differences required are possible in small Coulomb logarithm regimes, characterized by high density and low temperature. Ignition could be reached more easily if the fusion reactivity can be improved with nonthermal ion distributions. To establish an upper bound for the potential utility of a nonthermal distribution, we consider a monoenergetic beam with particle energy selected to maximize the beam-thermal reactivity. Comparing deuterium-tritium (DT) and p-{sup 11}B, themore » minimum Lawson criteria and minimum ρR required for inertial confinement fusion (ICF) volume ignition are calculated with and without the nonthermal feature. It turns out that channeling fusion alpha energy to maintain such a beam facilitates ignition at lower densities and ρR, improves reactivity at constant pressure, and could be used to remove helium ash. On the other hand, the reactivity gains that could be realized in DT plasmas are significant, the excess electron density in p-{sup 11}B plasmas increases the recirculated power cost to maintain a nonthermal feature and thereby constrains its utility to ash removal.« less

Low-temperature thermal decomposition of dioxin-like compounds in fly ash: combination of chemical analysis with in vitro bioassays (EROD and DR-CALUX).

PubMed

Behnisch, Peter A; Hosoe, Kazunori; Shiozaki, Ken; Ozaki, Hironori; Nakamura, Kazuo; Sakai, Shin-Ichi

2002-12-01

To investigate the dechlorination of fly ash during low-temperature treatment under oxygen-deficient conditions (thermocatalyic treatment or Hagenmaier process), six fly ash samples from six different incineration plants were treated in a laboratory experiment or in the actual plant, either under ideal (400 degrees C, 120 min) or intermediate (300 degrees C, 30 min) conditions. The aim of the present study was to confirm the decrease in the I-TEQ (international toxicity equivalency) of polychlorinated dibenzo-p-dioxins/-furans (PCDD/Fs) and coplanar polychlorinated biphenyls (co-PXBs) and, also for the first time, the decrease in the sum of dioxin-like toxicity (bioassay- or bio-TEQ) of all kinds of other dioxin-like Ah receptor agonists (such as PXDD/Fs, PXBs, PXN, X = Br, F) measured by two state-of-the-art cell-based Ah receptor-dependent bioassays: H4IIE-Ethoxy-Resorufin-o-Deethylase (EROD) and H4IIE-luc/DR-Chemical Activated Luciferase expression (DR-CALUX). The treatment efficiency was calculated on the basis of the reduction in the I-TEQ and bio-TED values. For these fly ash samples, the treatment efficiency, as measured by chemical analysis, was higher than 99%, and 85%-99%, in the case of the bio-TED values, indicating that these Ah receptor binding toxic compounds were sufficiently decomposed. Bio-TEQ values for untreated fly ash samples (n = 6) were on average 1.2 times (range 0.7-1.9), for the H4IIE-EROD assay, and 2.8 times (1.1-4.9), for the DR-CALUX assay, higher than I-TEQ values measured by chemical analyses (sum of PCDD/Fs and co-PCBs). In the case of these fly ash samples treated under ideal conditions and therefore low in contaminants, the bio-TEQ values were on average 1.4 times (range 0.9-1.8), for the H4IIE-EROD assay, and 5.1 times (range 1.2-12), for the DR-CALUX assay, higher than the I-TEQ values.

A six-year record of volcanic ash detection with Envisat MIPAS

NASA Astrophysics Data System (ADS)

Griessbach, S.; Hoffmann, L.; von Hobe, M.; Müller, R.; Spang, R.

2012-04-01

Volcanic ash particles have an impact on the Earth's radiation budget and pose a severe danger to air traffic. Therefore, the ability to detect and characterize volcanic ash layers on a global and altitude-dependent scale is essential. The Michelson Interferometer for Passive Atmospheric Sounding (MIPAS) on-board ESA's Envisat is mainly used for measurements of vertical profiles of atmospheric trace gases. It is also very sensitive to cloud and aerosol particles. We developed a fast, simple, and reliable method to detect volcanic ash using MIPAS spectra. From calculations of volcanic ash and ice particle optical properties, such as extinction coefficients and single scattering albedos as well as simulated MIPAS radiance spectra, we derived two optimal micro windows at 10.5 and 12.1 μm to detect volcanic ash. The calculations were performed with the JUelich RApid Spectral Simulation Code (JURASSIC), which includes a scattering module. Our method applies two radiance thresholds to detect volcanic ash. The first one is derived from a statistical analysis of six years of measured MIPAS radiances in the selected spectral windows. This statistical threshold accounts only for pure volcanic ash detections. The second threshold is derived from simulations of MIPAS radiances with JURASSIC for a broad range of atmospheric conditions and tangent altitudes for volcanic ash and ice particles. The second threshold allows more volcanic ash detections, because it accounts also for mixtures of ice and volcanic ash particles within the instrument's field of view. With the new method major eruptions (from e.g. Chaiten, Okmok, Kasatochi, Sarychev, Eyafjallajökull, Merapi, Grimsvötn, Puyehue-Cordon Caulle, Nabro) as well as several smaller eruptions at mid-latitudes and in polar regions between 2006 - 2011 were clearly identified in the MIPAS data. Trajectory calculations using the Chemical Langangian Model of the Stratosphere (CLaMS) are used to locate a volcanic eruption for each detection. In a case study of the 2011 eruption of the Chilean volcano Puyehue-Cordon Caulle we show how the volcanic ash spreads over the complete southern hemisphere mid-latitudes, is diluted and descends slowly with time. Ash is detected up to two month after the first eruption.

[Effects of Chinese prickly ash orchard on soil organic carbon mineralization and labile organic carbon in karst rocky desertification region of Guizhou province].

PubMed

Zhang, Wen-Juan; Liao, Hong-Kai; Long, Jian; Li, Juan; Liu, Ling-Fei

2015-03-01

Taking 5-year-old Chinese prickly ash orchard (PO-5), 17-year-old Chinese prickly ash orchard (PO- 17), 30-year-old Chinese prickly ash orchard (PO-30) and the forest land (FL, about 60 years) in typical demonstration area of desertification control test in southwestern Guizhou as our research objects, the aim of this study using a batch incubation experiment was to research the mineralization characteristics of soil organic carbon and changes of the labile soil organic carbon contents at different depths (0-15 cm, 15-30 cm, and 30-50 cm). The results showed that: the cumulative mineralization amounts of soil organic carbon were in the order of 30-year-old Chinese prickly ash orchard, the forest land, 5-year-old Chinese prickly ash orchard and 17-year-old Chinese prickly ash orchard at corresponding depth. Distribution ratios of CO2-C cumulative mineralization amount to SOC contents were higher in Chinese prickly ash orchards than in forest land at each depth. Cultivation of Chinese prickly ash in long-term enhanced the mineralization of soil organic carbon, and decreased the stability of soil organic carbon. Readily oxidized carbon and particulate organic carbon in forest land soils were significantly more than those in Chinese prickly ash orchards at each depth (P < 0.05). With the increasing times of cultivation of Chinese prickly ash, the contents of readily oxidized carbon and particulate organic carbon first increased and then declined at 0-15 cm and 15-30 cm depth, respectively, but an opposite trend was found at 30-50 cm depth. At 0-15 cm and 15-30 cm, cultivation of Chinese prickly ash could be good for improving the contents of labile soil organic carbon in short term, but it was not conducive in long-term. In this study, we found that cultivation of Chinese prickly ash was beneficial for the accumulation of labile organic carbon at the 30-50 cm depth.

Leachability of Heavy Metals from Lightweight Aggregates Made with Sewage Sludge and Municipal Solid Waste Incineration Fly Ash

PubMed Central

Wei, Na

2015-01-01

Lightweight aggregate (LWA) production with sewage sludge and municipal solid waste incineration (MSWI) fly ash is an effective approach for waste disposal. This study investigated the stability of heavy metals in LWA made from sewage sludge and MSWI fly ash. Leaching tests were conducted to find out the effects of MSWI fly ash/sewage sludge (MSWI FA/SS) ratio, sintering temperature and sintering time. It was found that with the increase of MSWI FA/SS ratio, leaching rates of all heavy metals firstly decreased and then increased, indicating the optimal ratio of MSWI fly ash/sewage sludge was 2:8. With the increase of sintering temperature and sintering time, the heavy metal solidifying efficiencies were strongly enhanced by crystallization and chemical incorporations within the aluminosilicate or silicate frameworks during the sintering process. However, taking cost-savings and lower energy consumption into account, 1100 °C and 8 min were selected as the optimal parameters for LWA sample- containing sludge production. Furthermore, heavy metal leaching concentrations under these optimal LWA production parameters were found to be in the range of China’s regulatory requirements. It is concluded that heavy metals can be properly stabilized in LWA samples containing sludge and cannot be easily released into the environment again to cause secondary pollution. PMID:25961800

Performance of Nitrogen and Phosphorus Removal in Petrochemical Wastewater by Zeolited Fly Ash

NASA Astrophysics Data System (ADS)

Li, Zheng; Gu, Guizhou; Ji, Shenghao

2018-05-01

The zeolitized fly ash was synthesized by alkali melt hydrothermal method. The cation exchange capacity of zeolitized fly ash was far greater than the raw material fly ash. The main component was NaP1 zeolite (Na6Al6Si10O32·12H2O), followed by mullite, and a small amount of heterozygous crystals. The effect of synthetic zeolite dosage, pH value, adsorption time and reaction temperature on the effect of nitrogen and phosphorus removal in petrochemical wastewater were investigated. The results showed that when the zeolitized fly ash dosage was 9 g/L, the petrochemical wastewater pH value was 6∼8, adsorption time was 30 min and the reaction temperature was 30°C, the synthetic zeolite had the best effect on the removal of TN and TP in petrochemical wastewater, and the removal was 65.5%, 91.4% respectively. Besides, the concentrations of TN and TP in the effluent were 11.04 mg/L, 0.31 mg/L respectively. The concentrations met the sewage discharge standard in petrochemical industry of "Liaoning sewage comprehensive discharge standard" (DB21 1627-2008). This study was to realize the comprehensive utilization of solid waste and achieve the purpose of waste and waste.

Leachability of heavy metals from lightweight aggregates made with sewage sludge and municipal solid waste incineration fly ash.

PubMed

Wei, Na

2015-05-07

Lightweight aggregate (LWA) production with sewage sludge and municipal solid waste incineration (MSWI) fly ash is an effective approach for waste disposal. This study investigated the stability of heavy metals in LWA made from sewage sludge and MSWI fly ash. Leaching tests were conducted to find out the effects of MSWI fly ash/sewage sludge (MSWI FA/SS) ratio, sintering temperature and sintering time. It was found that with the increase of MSWI FA/SS ratio, leaching rates of all heavy metals firstly decreased and then increased, indicating the optimal ratio of MSWI fly ash/sewage sludge was 2:8. With the increase of sintering temperature and sintering time, the heavy metal solidifying efficiencies were strongly enhanced by crystallization and chemical incorporations within the aluminosilicate or silicate frameworks during the sintering process. However, taking cost-savings and lower energy consumption into account, 1100 °C and 8 min were selected as the optimal parameters for LWA sample- containing sludge production. Furthermore, heavy metal leaching concentrations under these optimal LWA production parameters were found to be in the range of China's regulatory requirements. It is concluded that heavy metals can be properly stabilized in LWA samples containing sludge and cannot be easily released into the environment again to cause secondary pollution.

Significance of various soil amendments to borrow pit reclamation with loblolly pine and fescue

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berry, C.R.; Marx, D.H.

Loblolly pine seedlings with ectomycorrhizae formed by Pisolithus tinctorius (Pt) or naturally occurring Thelephora terrestris (Tt) were planted on a borrow pit in South Carolina in plots with no amendment; with fertilizer plus dolomitic limestone alone and with pine bark or bottom ash or bark and ash together; or with dried sewage sludge alone and with bark or ash or bark and ash together. All plots were subsoiled, disked, and seeded to fescue grass before planting pine seedlings. Naturally occurring Pt formed abundant ectomycorrhizae on all Tt seedlings by the end of the first season, precluding any specific ectomycorrhizal fungusmore » effect for the duration of the study. Sewage sludge alone or with bark or ash amendments dramatically improved pine seedling growth and grass biomass in comparison with other soil treatments. Mean seedling volume (D/sup 2/H) was 28 times greater and grass biomass was five times greater in the sludge plots than on nonsludge plots. Generally, soil amended with sludge contained more N, P, organic matter, and had a higher cation exchange capacity than soil of other treatments. Foliage of pine seedlings in sludge-amended soil also contained more N and less Ca than other seedlings. The significance of these results to reclamation of borrow pits is discussed.« less

Wigner time delay and spin-orbit activated confinement resonances

NASA Astrophysics Data System (ADS)

Keating, D. A.; Deshmukh, P. C.; Manson, S. T.

2017-09-01

A study of the photoionization of spin-orbit split subshells of high-Z atoms confined in C60 has been performed using the relativistic-random-phase approximation. Specifically, Hg@C60 5p, Rn@C60 6p and Ra@C60 5d were investigated and the near-threshold confinement resonances in the j = l - 1/2 channels were found to engender structures in the j = l + 1/2 cross sections via correlation in the form of interchannel coupling. These structures are termed spin-orbit induced confinement resonances and they are found to profoundly influence the Wigner time delay spectrum resulting in time delays of tens or hundreds of attoseconds along with dramatic swings in time delay over small energy intervals. Pronounced relativistic effects in time delay are also found. These structures, including their manifestation in time delay spectra, are expected to be general phenomena in the photoionization of spin-orbit doublets in confined high-Z atoms.

The emerald ash borer: a new exotic pest in North America

Treesearch

Robert A. Haack; Eduard Jendak; Liu Houping; Keneth R. Marchant; Toby R. Petrice; Therese M. Poland; Hui Ye

2002-01-01

Yet another new exotic forest pest has been discovered in North America, and this time the infestation is centered in Michigan and Ontario. In May and June 2002, adults of an unidentified buprestid beetle were collected from ash (Fraxinus) trees in the Detroit area of southeastern Michigan.

Volcanic ash and aviation–The challenges of real-time, global communication of a natural hazard

USGS Publications Warehouse

Lechner, Peter; Tupper, Andrew C.; Guffanti, Marianne C.; Loughlin, Sue; Casadevall, Thomas

2017-01-01

More than 30 years after the first major aircraft encounters with volcanic ash over Indonesia in 1982, it remains challenging to inform aircraft in flight of the exact location of potentially dangerous ash clouds on their flight path, particularly shortly after the eruption has occurred. The difficulties include reliably forecasting and detecting the onset of significant explosive eruptions on a global basis, observing the dispersal of eruption clouds in real time, capturing their complex structure and constituents in atmospheric transport models, describing these observations and modelling results in a manner suitable for aviation users, delivering timely warning messages to the cockpit, flight planners and air traffic management systems, and the need for scientific development in order to undertake operational enhancements. The framework under which these issues are managed is the International Airways Volcano Watch (IAVW), administered by the International Civil Aviation Organization (ICAO). ICAO outlines in its standards and recommended practices (International Civil Aviation Organization, 2014) the basic volcanic monitoring and communication that is necessary at volcano observatories in Member States (countries). However, not all volcanoes are monitored and not all countries with volcanoes have mandated volcano observatories or equivalents. To add to the efforts of volcano observatories, a system of Meteorological Watch Offices, Air Traffic Management Area Control Centres, and nine specialist Volcanic Ash Advisory Centres (VAACs) are responsible for observing, analysing, forecasting and communicating the aviation hazard (airborne ash), using agreed techniques and messages in defined formats. Continuous improvement of the IAVW framework is overseen by expert groups representing the operators of the system, the user community, and the science community. The IAVW represents a unique marriage of two scientific disciplines - volcanology and meteorology - with the aviation user community. There have been many multifaceted volcanic eruptions in complex meteorological conditions during the history of the IAVW. Each new eruption brings new insights into how the warning system can be improved, and each reinforces the lessons that have gone before. The management of these events has improved greatly since the major ash encounters in the 1980s, but discontinuities in the warning and communications system still occur. A good example is a 2014 ash encounter over Indonesia following the eruption of Kelut where the warnings did not reach the aircraft crew. Other events present enormous management challenges – for example the 2010 Eyjafjallajökull eruption in Iceland was, overall, less hazardous than many less publicised eruptions, but numerous small to moderate explosions over several weeks produced widespread disruption and a large economic impact. At the time of writing, while there has been hundreds of millions of US dollars in damage to aircraft from encounters with ash, there have been no fatalities resulting from aviation incidents in, or proximal to volcanic ash cloud. This reflects, at least in part, the hard work done in putting together a global warning system - although to some extent it also reflects a measure of good statistical fortune. In order to minimise the risk of aircraft encounters with volcanic ash clouds, the global effort continues. The future priorities for the IAVW are strongly focused on enhancing communication before, and at the very onset of a volcanic ash-producing event (typically the more dangerous stage), together with improved downstream information and warning systems to help reduce the economic impact of eruptions on aviation.

Development of an ash particle deposition model considering build-up and removal mechanisms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kjell Strandstroem; Christian Muellera; Mikko Hupa

2007-12-15

Slagging and fouling on heat exchanger surfaces in power boilers fired with fossil fuels and fuel mixtures has a significant influence on boiler efficiency and availability. Mathematical modelling has long been considered a suitable method to assist boiler operators to determine optimized operating conditions for an existing furnace. The ultimate goal in ash deposition prediction is hereby the determination of the total amount of material deposited and hence the determination of the total reduction in efficiency. Depending on the fuels fired the total deposited mass is a combination of ash particle deposition and ash particle erosion due to non-sticky particles.more » The novel ash particle deposition model presented in this work considers deposition of sticky ash particles, cleansing of deposit by non-sticky sand particles and sticking of sand due to contact with sticky ash. The steady-state modelling results for the total amount of ash deposited on the deposition probe of an entrained flow reactor presented in this work agree well with the experimental data. Only at very high fractions of sand added as non-sticky material, a significant influence of the sand on the overall mass deposited was found. Since the model considers sticking of non-sticking sand due to contact with sticky ash, the fraction of sand deposited on the probe was especially studied. Using a correction factor to consider the influence of operating time on the steady-state simulations led to good agreement between simulations and experimental data. 12 refs., 10 figs.« less

Thermal and hydrometallurgical recovery methods of heavy metals from municipal solid waste fly ash.

PubMed

Kuboňová, L; Langová, Š; Nowak, B; Winter, F

2013-11-01

Heavy metals in fly ash from municipal solid waste incinerators are present in high concentrations. Therefore fly ash must be treated as a hazardous material. On the other hand, it may be a potential source of heavy metals. Zinc, lead, cadmium, and copper can be relatively easily removed during the thermal treatment of fly ash, e.g. in the form of chlorides. In return, wet extraction methods could provide promising results for these elements including chromium and nickel. The aim of this study was to investigate and compare thermal and hydrometallurgical treatment of municipal solid waste fly ash. Thermal treatment of fly ash was performed in a rotary reactor at temperatures between 950 and 1050°C and in a muffle oven at temperatures from 500 to 1200°C. The removal more than 90% was reached by easy volatile heavy metals such as cadmium and lead and also by copper, however at higher temperature in the muffle oven. The alkaline (sodium hydroxide) and acid (sulphuric acid) leaching of the fly ash was carried out while the influence of temperature, time, concentration, and liquid/solid ratio were investigated. The combination of alkaline-acidic leaching enhanced the removal of, namely, zinc, chromium and nickel. Copyright © 2013 Elsevier Ltd. All rights reserved.

Angular dependence of EWS time delay for photoionization of @Xe

NASA Astrophysics Data System (ADS)

Mandal, Ankur; Deshmukh, Pranawa; Kheifets, Anatoli; Dolmatov, Valeriy; Manson, Steven

2017-04-01

Interference between photoionization channels leads to angular dependence in photoionization time delay. Angular dependence is found to be a common effect for two-photon absorption experiments very recently. The effect of confinement on the time delay where each partial wave contributions to the ionization are studied. In this work we report angular dependence and confinement effects on Eisenbud-Wigner-Smith (EWS) time delay in atomic photoionization. Using and we computed the EWS time delay for free and confined Xe atom for photoionization from inner 4d3/2 and 4d5/2 and outer 5p1/2 and 5p3/2 subshells at various angles. The calculated EWS time delay is few tens to few hundreds of attoseconds (10-18 second). The photoionization time delay for @Xe follows that in the free Xe atom on which the confinement oscillations are built. The present work reveals the effect of confinement on the photoionization time delay at different angles between photoelectron ejection and the photon polarization.

Effects of a layer of vegetative ash layer on wettable and water repellent soil hydrology

NASA Astrophysics Data System (ADS)

Bodí, Merche B.; Doerr, Stefan H.; Cerdà, Artemi; Mataix-Solera, Jorge

2010-05-01

Following a wildfire, a layer of vegetative ash often covers the ground until it is dissolved or redistributed by wind and water erosion. Much of the existing literature suggests that the ash layer temporally reduces infiltration by clogging soil pores or by forming a surface crust (Mallik et al., 1984; Onda et al., 2008). However, an increasing number of field-based studies have found that, at least in the short term, ash increases infiltration by storing rainfall and protecting the underlying soil from sealing (Cerdà and Doerr, 2008; Woods and Balfour, 2008). On the other hand, after a fire the soil may have produced, enhanced or reduced its water repellency (Doerr et al., 2000). Very few studies have been taken into account the interaction of the ash and the repellent soil. The layer of ash may have similar role as a litter layer in delaying runoff and reducing erosion by storing water. In order to examine this interaction, it was been made a series of experiments using a laboratory rainfall simulation. It has been assessed the effects of an ash layer i) on a wettable and water repellent soil (WDPT > 7200s), ii) with different ash thicknesses (bare soil and 5 mm, 15 mm and 30 mm of ash), iii) preceding and following the first rain after a fire when the ground is still wetted and after being partially dried. Three replicates were done, being a total of 40 simulations. The ash used was collected from a Wildfire in Teruel (Spain) during summer of 2009. The simulations were conducted in metal boxes of 30x30 cm and filled with 3 cm of soil. The slope of the box was set at 10° (17%) and the intensity applied was 78-84 mm h-1during 40 minutes. The splash detachment was determined also using four splash cups. Overland flow and subsurface drainage was collected at 1-minute intervals and the former stored every 5 min to allow determination of sediment concentrations, yield and erosion rates. Each sample was examined at the end in terms of water repellency, infiltration pattern and ash incorporation into the soil. The results show that when ash covers the wettable soil, runoff occur for a short period of time in the middle of the event. It occurred latter on time but larger in quantity as the ash thickness increases (from 0% to 2% of runoff coefficient) and at the same time drainage is reduced (from 57 to 24%). This suggests that the ash layer became saturated and produce runoff until the water is able to drain into the soil. Oppositely, in water repellent soil as ash thickness increases both runoff is reduced (from 78% to 26%) and drainage is increased (from 0 to 16%). That fact indicates a modification in the hydraulic conductivity of the repellent soil due to the pressure of the ash layer. Splash and erosion rates are bigger in water repellent soils yet erosion rates never exceed 2.5 g m-2 h-1. The fact of wetting increases the runoff and drainage rates in wettable but reduce them in the water repellent soil. An irregular infiltration pattern is observed afterwards. After drying the soil, the increase in runoff indicates a crust formation. Moreover, in water repellent soils part of the repellency is reestablished. These findings demonstrate that the interaction of the soil-ash layer should be considered and better studied in the immediate hydrological response after wildfire due to its particular behavior. References Cerdà, A. and Doerr, S.H., 2008. The effect of ash and needle cover on surface runoff and erosion in the immediate post-fire period. Catena, 74: 256-263. Doerr, S.H., Shakesby, R.A. and Walsh, R.P.D., 2000. Soil Water repellency: Its causes, characteristics and hydro-geomorphological significance. Earth Science Reviews, 51: 33-65. Mallik, A.U., Gimingham, C.H. and Rahman, A.A., 1984. Ecological effects of heater burning. I. Water infiltration, moisture retention and porosity of surface soil. Journal of Ecology, 72: 767-776. Onda, Y., Dietrich, W.E. and Booker, F., 2008. Evolution of overland flow after a severe forest fire, Point Reyes, California. Catena, 72: 13-20. Woods, S.W. and Balfour, V., 2008. The effect of ash on runoff and erosion after a forest wildfire, Montana, U.S.A. International Journal of Wildland Fire, 17(5): 535-548.

Chemical and ecotoxicological characterization of ashes obtained from sewage sludge combustion in a fluidised-bed reactor.

PubMed

Lapa, N; Barbosa, R; Lopes, M H; Mendes, B; Abelha, P; Boavida, D; Gulyurtlu, I; Oliveira, J Santos

2007-08-17

In 1999, the DEECA/INETI and the UBiA/FCT/UNL started a researching project on the partition of heavy metals during the combustion of stabilised sewage sludge (Biogran), in a fluidised-bed reactor, and on the quality of the bottom ashes and fly ashes produced. This project was entitled Bimetal and was funded by the Portuguese Foundation for Science and Technology. In this paper only the results on the combustion of Biogran are reported. The combustion process was performed in two different trials, in which different amounts of sewage sludge and time of combustion were applied. Several ash samples were collected from the bed (bottom ashes) and from two cyclones (first cyclone and second cyclone ashes). Sewage sludge, bed material (sand) and ash samples were submitted to the leaching process defined in the European leaching standard EN 12457-2. The eluates were characterized for a set of inorganic chemical species. The ecotoxicological levels of the eluates were determined for two biological indicators (Vibrio fischeri and Daphnia magna). The results were compared with the limit values of the CEMWE French Regulation. The samples were also ranked according to an index based on the chemical characterization of the eluates. It was observed an increase of the concentration of metals along the combustion system. The ashes trapped in the second cyclone, for both combustion trials, showed the highest concentration of metals in the eluates. Chemically, the ashes of the second cyclone were the most different ones. In the ecotoxicological point of view, the ecotoxicity levels of the eluates of the ashes, for both combustion cycles, did not follow the same pattern as observed for the chemical characterization. The ashes of the first cyclone showed the highest ecotoxicity levels for V. fischeri and D. magna. This difference on chemical and ecotoxicological results proves the need for performing both chemical and ecotoxicological characterizations of the sub-products of such type of thermal processes.

Evaluation of heavy metal leaching from coal ash-versus conventional concrete monoliths and debris.

PubMed

Gwenzi, Willis; Mupatsi, Nyarai M

2016-03-01

Application of coal ash in construction materials is constrained by the potential risk of heavy metal leaching. Limited information is available on the comparative heavy metal leaching from coal ash-versus conventional concrete. The current study compared total and leached heavy metal concentrations in unbound coal ash, cement and sand; and investigated the effect of initial leachant pH on heavy metal leaching from coal-ash versus conventional concrete monoliths and their debris. Total Pb, Mn and Zn in coal ash were lower than or similar to that of other materials, while Cu and Fe showed the opposite trend. Leached concentrations of Zn, Pb, Mn, Cu and Fe in unbound coal ash, its concrete and debris were comparable and in some cases even lower than that for conventional concrete. In all cases, leached concentrations accounted for just <1% of the total concentrations. Log-log plots of concentration and cumulative release of Fe versus time based on tank leaching data showed that leaching was dominated by diffusion. Overall, the risk of Zn, Pb, Mn, Cu and Fe leaching from coal ash and its concrete was minimal and comparable to that of conventional concrete, a finding in contrast to widely held public perceptions and earlier results reported in other regions such as India. In the current study the coal ash, and its concrete and debris had highly alkaline pH indicative of high acid neutralizing and pH buffering capacity, which account for the stabilization of Zn, Pb, Mn, Cu and Fe. Based on the low risk of Zn, Pb, Mn, Cu and Fe leaching from the coal ash imply that such coal ash can be incorporated in construction materials such as concrete without adverse impacts on public and environmental health from these constituents. Copyright © 2015 Elsevier Ltd. All rights reserved.

Satellite Monitoring of Ash and Sulphur Dioxide for the mitigation of Aviation Hazards: Part I. Validation of satellite-derived Volcanic Ash Levels.

NASA Astrophysics Data System (ADS)

Koukouli, MariLiza; Balis, Dimitris; Simopoulos, Spiros; Siomos, Nikos; Clarisse, Lieven; Carboni, Elisa; Wang, Ping; Siddans, Richard; Marenco, Franco; Mona, Lucia; Pappalardo, Gelsomina; Spinetti, Claudia; Theys, Nicolas; Tampellini, Lucia; Zehner, Claus

2014-05-01

The 2010 eruption of the Icelandic volcano Eyjafjallajökull attracted the attention of the public and the scientific community to the vulnerability of the European airspace to volcanic eruptions. Major disruptions in European air traffic were observed for several weeks surrounding the two eruptive episodes, which had a strong impact on the everyday life of many Europeans as well as a noticable economic loss of around 2-3 billion Euros in total. The eruptions made obvious that the decision-making bodies were not informed properly and timely about the commercial aircraft capabilities to ash-leaden air, and that the ash monitoring and prediction potential is rather limited. After the Eyjafjallajökull eruptions new guidelines for aviation, changing from zero tolerance to newly established ash threshold values, were introduced. Within this spirit, the European Space Agency project Satellite Monitoring of Ash and Sulphur Dioxide for the mitigation of Aviation Hazards, called for the creation of an optimal End-to-End System for Volcanic Ash Plume Monitoring and Prediction . This system is based on improved and dedicated satellite-derived ash plume and sulphur dioxide level assessments, as well as an extensive validation using auxiliary satellite, aircraft and ground-based measurements. The validation of volcanic ash levels extracted from the sensors GOME-2/MetopA, IASI/MetopA and MODIS/Terra and MODIS/Aqua is presented in this work with emphasis on the ash plume height and ash optical depth levels. Co-located aircraft flights, Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation [CALIPSO] soundings and well as European Aerosol Research Lidar Network [EARLINET] measurements were compared to the different satellite estimates for the those two eruptive episodes. The validation results are extremely promising with most satellite sensors performing quite well and within the estimated uncertainties compared to the comparative datasets. The findings are extensively presented here and future directions discussed in length.

Late Pleistocene eruptive history of the Mono Craters rhyolites, eastern California, from U-Th dating of explosive and effusive products

NASA Astrophysics Data System (ADS)

Marcaida, M.; Vazquez, J. A.; Calvert, A. T.; Miller, J. S.

2016-12-01

During late Pleistocene-Holocene time, repeated explosive and effusive eruptions of high-silica rhyolite magma south of Mono Lake, California, have produced a chain of massive domes known as the Mono Craters and a time-series of tephra deposits preserved in sediments of the Wilson Creek formation of ancestral Mono Lake. The record of late Holocene volcanism at Mono Craters is relatively well constrained by tephrostratigraphy and 14C dating, and the timing of late Pleistocene eruptions is similarly well constrained by tephrochronology and magnetostratigraphy of the Wilson Creek formation. However, the chronology of eruptions for the Mono Craters chain, comprising at least 28 individual domes, has thus far been based on age estimates from hydration rind dating of obsidian that is highly dependent on local calibration. We constrain the timing of late Pleistocene dome emplacement by linking independently dated Wilson Creek tephras to their dome equivalents in the Mono Craters using combined titanomagnetite geochemistry and U-Th geochronology. Ion microprobe 238U-230Th dating of unpolished allanite and zircon rims gives isochron dates of ca. 42 ka, ca. 38 ka, ca. 26 ka, and ca. 20 ka for domes 19, 24, 31 (newly recognized), and 11 of the Mono Craters, respectively. These domes are biotite-bearing rhyolites with titanomagnetites that are compositionally identical to those from several Wilson Creek tephras. Specifically, we correlate Ash 15, Ash 7, and Ash 3 of the Wilson Creek formation to domes 19, 31, and 11 of the Mono Craters, respectively, based on matching titanomagnetite compositions and indistinguishable U-Th ages. 40Ar/39Ar dating of single sanidines from domes 19 and 31 yield mean dates that are 10 k.y. older than their corresponding U-Th dates, likely due to excess argon from melt inclusions and/or incompletely re-equilibrated antecrysts. Based on our new U-Th isochron date of ca. 34 ka for allanite-zircon from Ash 8 pumice and the ca. 26-27 ka age of Ash 7 and its extrusive equivalent dome 31, we infer that the stratigraphic position of the ca. 32 ka Auckland/Mono Lake geomagnetic excursion, if recorded in beds of the Wilson Creek formation, is between Ashes 7 and 8. Accordingly, the prominent geomagnetic excursion bisected by Ash 15 lower in the section is the ca. 41 ka global Laschamp event.

The effects of the mechanical–chemical stabilization process for municipal solid waste incinerator fly ash on the chemical reactions in cement paste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Cheng-Gang; Sun, Chang-Jung, E-mail: sun.3409@hotmail.com; Gau, Sue-Huai

2013-04-15

Highlights: ► Milling extracted MSWI fly ash. ► Increasing specific surface area, destruction of the crystalline texture, and increasing the amount of amorphous materials. ► Increasing heavy metal stability. ► Inducing pozzolanic reactions and increasing the early and later strength of the cement paste. - Abstract: A water extraction process can remove the soluble salts present in municipal solid waste incinerator (MSWI) fly ash, which will help to increase the stability of the synthetic materials produced from the MSWI fly ash. A milling process can be used to stabilize the heavy metals found in the extracted MSWI fly ash (EA)more » leading to the formation of a non-hazardous material. This milled extracted MSWI fly ash (MEA) was added to an ordinary Portland cement (OPC) paste to induce pozzolanic reactions. The experimental parameters included the milling time (96 h), water to binder ratios (0.38, 0.45, and 0.55), and curing time (1, 3, 7 and 28 days). The analysis procedures included inductively coupled plasma atomic emission spectroscopy (ICP/AES), BET, mercury intrusion porosimetry (MIP), X-ray diffraction (XRD), and nuclear magnetic resonance (NMR) imaging. The results of the analyses indicate that the milling process helped to stabilize the heavy metals in the MEA, with an increase in the specific surface area of about 50 times over that of OPC. The addition of the MEA to the OPC paste decreased the amount of Ca(OH){sub 2} and led to the generation of calcium–silicate–hydrates (C–S–H) which in turned increased the amount of gel pores and middle sized pores in the cement. Furthermore, a comparison shows an increase in the early and later strength over that of OPC paste without the addition of the milled extracted ash. In other words, the milling process could stabilize the heavy metals in the MEA and had an activating effect on the MEA, allowing it to partly substitute OPC in OPC paste.« less

Confined space emergency response: assessing employer and fire department practices.

PubMed

Wilson, Michael P; Madison, Heather N; Healy, Stephen B

2012-01-01

An emergency response plan for industrial permit-required confined space entry is essential for employee safety and is legally required. Maintaining a trained confined space rescue team, however, is costly and technically challenging. Some employers turn to public fire departments to meet their emergency response requirements. The confined space emergency response practices of employers and fire departments have not been previously assessed. We present (1) federal data on the U.S. occurrence between 1992 and 2005 of confined space fatal incidents involving toxic and/or oxygen-deficient atmospheres; (2) survey data from 21 large companies on permit-required confined space emergency response practices; (3) data on fire department arrival times; and (4) estimates by 10 senior fire officers of fire department rescue times for confined space incidents. Between 1992 and 2005, 431 confined space incidents that met the case definition claimed 530 lives, or about 0.63% of the 84,446 all-cause U.S. occupational fatal injuries that occurred during this period. Eighty-seven (20%) incidents resulted in multiple fatalities. Twelve (57%) of 21 surveyed companies reported that they relied on the fire department for permit-required confined space emergency response. Median fire department arrival times were about 5 min for engines and 7 min for technical rescue units. Fire department confined space rescue time estimates ranged from 48 to 123 min and increased to 70 and 173 min when hazardous materials were present. The study illustrates that (1) confined space incidents represent a small but continuing source of fatal occupational injuries in the United States; (2) a sizeable portion of employers may be relying on public fire departments for permit-required confined space emergency response; and (3) in the event of a life-threatening emergency, fire departments usually are not able to effect a confined space rescue in a timely manner. We propose that the appropriate role for the fire department is to support a properly trained and equipped on-site rescue team and to provide advanced life support intervention following extrication and during ambulance transportation.

Synthesis and characterization of grinding aid fly ash blended mortar effect on bond strength of masonry prisms

NASA Astrophysics Data System (ADS)

Krishnaraj, L.; Ravichandran, P. T.; Sagadevan, Suresh

2018-04-01

The aim of the present work is to study the effect of particle size reduction by applying top-down nanotechnology such as ball mill grinding process with the addition of amine-based grinding aids. The particle size reduction in synthesis process and its characterization were investigated for fly ash particles. The Rosin-Rammler-Bennet (RRB) distribution model using mathematical formulations were studied for fly ash ground particles. The hardened properties of grinding aid fly ash composite mortar were studied using compressive strength test. The optimum grinding time was 120 min identified through the particle size distribution analysis. The mean particle size decreased from 92.09 μm to 10.5 μm in which there is 89% reduction in particle size due to the grinding of fly ash particle with grinding aids. The compressive strength results show that substitutions of Ordinary Portland Cement (OPC) mortar by Amine-based Grinding aid Fly Ash (AGFA) 15% gives 12, 23% and at 30% gives 6, 8% of higher strength compare to the substitutions of raw fly ash. The addition of grinding aids in grinding process gives more advantages to reduce the particle size without changing chemical composition. The AGFA sample shows better performance in compressive strength and bond strength behavior of masonry prism. It may suggest that amine based grinding aids play a vital role and feasible to use in fly ash grinding process.

Adsorption of Cu2+ to biomass ash and its modified product.

PubMed

Xu, Lei; Cui, Hongbiao; Zheng, Xuebo; Liang, Jiani; Xing, Xiangyu; Yao, Lunguang; Chen, Zhaojin; Zhou, Jing

2017-04-01

Ash produced by biomass power plants has great potential for the removal of heavy metal ions from aqueous solution. The pollution of toxic heavy metals to water is a worldwide environmental problem. Discharges containing copper, in particular, are strictly controlled because the excessive copper can cause serious harm to the environment and human health. This work aims to investigate the adsorption characteristics of copper ions in aqueous solution by biomass ash and the modified products, and to evaluate their potential application in water pollution control. The biomass ash was modified with a mesoporous siliceous material and functionalized with 3-aminopropyltriethoxysilane. The surface properties of the biomass ash and the new matrix were studied to evaluate their adsorption property for Cu 2+ ions at different pHs, initial metal concentrations and the thermodynamic and kinetic were studied. The chemical and morphological properties of this modified material are analyzed; the specific surface area of the modified biomass ash was nine times that of the initial ash. Both of the two materials showed a strong affinity for Cu 2+ , and the Langmuir model could best represent the adsorption characteristics of Cu 2+ on the two kinds of materials. The adsorption capacity of copper on the material increased with the increase of pH and pH 6 was the optimum pH. Thermodynamic analysis results showed that the adsorption of Cu 2+ was spontaneous and endothermic in nature. The adsorptions of Cu 2+ onto the modified biomass ash followed pseudo-second-order kinetics.

A pilot study of mercury liberation and capture from coal-fired power plant fly ash.

PubMed

Li, Jin; Gao, Xiaobing; Goeckner, Bryna; Kollakowsky, Dave; Ramme, Bruce

2005-03-01

The coal-fired electric utility generation industry has been identified as the largest anthropogenic source of mercury (Hg) emissions in the United States. One of the promising techniques for Hg removal from flue gas is activated carbon injection (ACI). The aim of this project was to liberate Hg bound to fly ash and activated carbon after ACI and provide high-quality coal combustion products for use in construction materials. Both bench- and pilot-scale tests were conducted to liberate Hg using a thermal desorption process. The results indicated that up to 90% of the Hg could be liberated from the fly ash or fly-ash-and-activated-carbon mixture using a pilot-scale apparatus (air slide) at 538 degrees C with a very short retention time (less than 1 min). Scanning electron microscope (SEM) evaluation indicated no significant change in fly ash carbon particle morphology following the thermal treatment. Fly ash particles collected in the baghouse of the pilot-scale apparatus were smaller in size than those collected at the exit of the air slide. A similar trend was observed in carbon particles separated from the fly ash using froth flotation. The results of this study suggest a means for power plants to reduce the level of Hg in coal-combustion products and potentially recycle activated carbon while maintaining the resale value of fly ash. This technology is in the process of being patented.

Chemical and physical properties of cyclone fly ash from the grate-fired boiler incinerating forest residues at a small municipal district heating plant (6MW).

PubMed

Pöykiö, R; Rönkkömäki, H; Nurmesniemi, H; Perämäki, P; Popov, K; Välimäki, I; Tuomi, T

2009-03-15

In Finland, the new limit values for maximal allowable heavy metal concentrations for materials used as an earth construction agent came into force in July 2006. These limit values are applied if ash is utilized, e.g. in roads, cycling paths, pavements, car parks, sport fields, etc. In this study we have determined the most important chemical and physical properties of the cyclone fly ash originating from the grate-fired boiler incinerating forest residues (i.e. wood chips, sawdust and bark) at a small municipal district heating plant (6 MW), Northern Finland. This study clearly shows that elements are enriched in cyclone fly ash, since the total element concentrations in the cyclone fly ash were within 0.2-10 times higher than those in the bottom ash. The total concentrations of Cd (25 mg kg(-1); d.w.), Zn (3630 mg kg(-1); d.w.), Ba (4260 mg kg(-1); d.w.) and Hg (1.7 mg kg(-1); d.w.) exceeded the limit values, and therefore the cyclone fly ash cannot be used as an earth construction agent. According to the leached amounts of Cr (38 mg kg(-1); d.w.), Zn (51 mg kg(-1); d.w.) and sulphate (50,000 mg kg(-1); d.w.), the cyclone fly ash is classified as a hazardous waste, and it has to be deposited in a hazardous waste landfill.

Angle-resolved Wigner time delay in atomic photoionization: The 4 d subshell of free and confined Xe

NASA Astrophysics Data System (ADS)

Mandal, A.; Deshmukh, P. C.; Kheifets, A. S.; Dolmatov, V. K.; Manson, S. T.

2017-11-01

The angular dependence of photoemission time delay for the inner n d3 /2 and n d5 /2 subshells of free and confined Xe is studied in the dipole relativistic random phase approximation. A finite spherical annular well potential is used to model the confinement due to fullerene C60 cage. Near cancellations in a variety of the dipole amplitudes, Cooper-like minima, are found. The effects of confinement on the angular dependence, primarily confinement resonances, are demonstrated and detailed.

Satellite Observations of Volcanic Clouds from the Eruption of Redoubt Volcano, Alaska, 2009

NASA Astrophysics Data System (ADS)

Dean, K. G.; Ekstrand, A. L.; Webley, P.; Dehn, J.

2009-12-01

Redoubt Volcano began erupting on 23 March 2009 (UTC) and consisted of 19 events over a 14 day period. The volcano is located on the Alaska Peninsula, 175 km southwest of Anchorage, Alaska. The previous eruption was in 1989/1990 and seriously disrupted air traffic in the region, including the near catastrophic engine failure of a passenger airliner. Plumes and ash clouds from the recent eruption were observed on a variety of satellite data (AVHRR, MODIS and GOES). The eruption produced volcanic clouds up to 19 km which are some of the highest detected in recent times in the North Pacific region. The ash clouds primarily drifted north and east of the volcano, had a weak ash signal in the split window data and resulted in light ash falls in the Cook Inlet basin and northward into Alaska’s Interior. Volcanic cloud heights were measured using ground-based radar, and plume temperature and wind shear methods but each of the techniques resulted in significant variations in the estimates. Even though radar showed the greatest heights, satellite data and wind shears suggest that the largest concentrations of ash may be at lower altitudes in some cases. Sulfur dioxide clouds were also observed on satellite data (OMI, AIRS and Calipso) and they primarily drifted to the east and were detected at several locations across North America, thousands of kilometers from the volcano. Here, we show time series data collected by the Alaska Volcano Observatory, illustrating the different eruptive events and ash clouds that developed over the subsequent days.

Preliminary volcano-hazard assessment for Akutan Volcano east-central Aleutian Islands, Alaska

USGS Publications Warehouse

Waythomas, Christopher F.; Power, John A.; Richter, Donlad H.; McGimsey, Robert G.

1998-01-01

Akutan Volcano is a 1100-meter-high stratovolcano on Akutan Island in the east-central Aleutian Islands of southwestern Alaska. The volcano is located about 1238 kilometers southwest of Anchorage and about 56 kilometers east of Dutch Harbor/Unalaska. Eruptive activity has occurred at least 27 times since historical observations were recorded beginning in the late 1700?s. Recent eruptions produced only small amounts of fine volcanic ash that fell primarily on the upper flanks of the volcano. Small amounts of ash fell on the Akutan Harbor area during eruptions in 1911, 1948, 1987, and 1989. Plumes of volcanic ash are the primary hazard associated with eruptions of Akutan Volcano and are a major hazard to all aircraft using the airfield at Dutch Harbor or approaching Akutan Island. Eruptions similar to historical Akutan eruptions should be anticipated in the future. Although unlikely, eruptions larger than those of historical time could generate significant amounts of volcanic ash, fallout, pyroclastic flows, and lahars that would be hazardous to life and property on all sectors of the volcano and other parts of the island, but especially in the major valleys that head on the volcano flanks. During a large eruption an ash cloud could be produced that may be hazardous to aircraft using the airfield at Cold Bay and the airspace downwind from the volcano. In the event of a large eruption, volcanic ash fallout could be relatively thick over parts of Akutan Island and volcanic bombs could strike areas more than 10 kilometers from the volcano.

Emergency Hospital Visits in Association with Volcanic Ash, Dust Storms and Other Sources of Ambient Particles: A Time-Series Study in Reykjavík, Iceland

PubMed Central

Carlsen, Hanne Krage; Gislason, Thorarinn; Forsberg, Bertil; Meister, Kadri; Thorsteinsson, Throstur; Jóhannsson, Thorsteinn; Finnbjornsdottir, Ragnhildur; Oudin, Anna

2015-01-01

Volcanic ash contributed significantly to particulate matter (PM) in Iceland following the eruptions in Eyjafjallajökull 2010 and Grímsvötn 2011. This study aimed to investigate the association between different PM sources and emergency hospital visits for cardiorespiratory causes from 2007 to 2012. Indicators of PM10 sources; “volcanic ash”, “dust storms”, or “other sources” (traffic, fireworks, and re-suspension) on days when PM10 exceeded the daily air quality guideline value of 50 µg/m3 were entered into generalized additive models, adjusted for weather, time trend and co-pollutants. The average number of daily emergency hospital visits was 10.5. PM10 exceeded the air quality guideline value 115 out of 2191 days; 20 days due to volcanic ash, 14 due to dust storms (two days had both dust storm and ash contribution) and 83 due to other sources. High PM10 levels from volcanic ash tended to be significantly associated with the emergency hospital visits; estimates ranged from 4.8% (95% Confidence Interval (CI): 0.6, 9.2%) per day of exposure in unadjusted models to 7.3% (95% CI: −0.4, 15.5%) in adjusted models. Dust storms were not consistently associated with daily emergency hospital visits and other sources tended to show a negative association. We found some evidence indicating that volcanic ash particles were more harmful than particles from other sources, but the results were inconclusive and should be interpreted with caution. PMID:25872017

Recycle of Inorganic Nutrients for Hydroponic Crop Production Following Incineration of Inedible Biomass

NASA Technical Reports Server (NTRS)

Bubenheim, David L.; Wignarajah, Kanapathipillai; Kliss, Mark H. (Technical Monitor)

1996-01-01

Recovery of resources from waste streams is essential for future implementation and reliance on a regenerative life support system. The major waste streams of concern are from human activities and plant wastes. Carbon, water and inorganics are the primary desired raw materials of interest. The goal of resource recovery is maintenance of product quality to insure support of reliable and predictable levels of life support function performance by the crop plant component. Further, these systems must be maintained over extended periods of time, requiring maintenance of nutrient solutions to avoid toxicity and deficiencies. Today, reagent grade nutrients are used to make nutrient solutions for hydroponic culture and these solutions are frequently changed during the life cycle or sometimes managed for only one crop life cycle. The focus of this study was to determine the suitability of the ash product following incineration of inedible biomass as a source of inorganic nutrients for hydroponic crop production. Inedible wheat biomass was incinerated and ash quality characterized. The incinerator ash was dissolved in adequate nitric acid to establish a consistent nitrogen concentration in all nutrient solution treatments. Four experimental nutrient treatments were included: control, ash only, ash supplemented to match control, and ash only quality formulated with reagent grade chemicals. When nutrient solutions are formulated using only ash following-incineration of inedible biomass, a balance in solution is established representing elemental retention following incineration and nutrient proportions present in the original biomass. The resulting solution is not identical to the control. This imbalance resulted in suppression of crop growth. When the ash is supplemented with nutrients to establish the same balance as in the control, growth is identical to the control. The ash appears to carry no phytotoxic materials. Growth in solution formulated with reagent grade chemicals but matching the quality of the ash only treatment resulted in growth similar to that of the ash only treatment. The ash product resulting from incineration of inedible biomass appears to be a suitable form for recycle of inorganic nutrients to crop production.

Thermal noise in confined fluids.

PubMed

Sanghi, T; Aluru, N R

2014-11-07

In this work, we discuss a combined memory function equation (MFE) and generalized Langevin equation (GLE) approach (referred to as MFE/GLE formulation) to characterize thermal noise in confined fluids. Our study reveals that for fluids confined inside nanoscale geometries, the correlation time and the time decay of the autocorrelation function of the thermal noise are not significantly different across the confinement. We show that it is the strong cross-correlation of the mean force with the molecular velocity that gives rise to the spatial anisotropy in the velocity-autocorrelation function of the confined fluids. Further, we use the MFE/GLE formulation to extract the thermal force a fluid molecule experiences in a MD simulation. Noise extraction from MD simulation suggests that the frequency distribution of the thermal force is non-Gaussian. Also, the frequency distribution of the thermal force near the confining surface is found to be different in the direction parallel and perpendicular to the confinement. We also use the formulation to compute the noise correlation time of water confined inside a (6,6) carbon-nanotube (CNT). It is observed that inside the (6,6) CNT, in which water arranges itself in a highly concerted single-file arrangement, the correlation time of thermal noise is about an order of magnitude higher than that of bulk water.

Thermal noise in confined fluids

NASA Astrophysics Data System (ADS)

Sanghi, T.; Aluru, N. R.

2014-11-01

In this work, we discuss a combined memory function equation (MFE) and generalized Langevin equation (GLE) approach (referred to as MFE/GLE formulation) to characterize thermal noise in confined fluids. Our study reveals that for fluids confined inside nanoscale geometries, the correlation time and the time decay of the autocorrelation function of the thermal noise are not significantly different across the confinement. We show that it is the strong cross-correlation of the mean force with the molecular velocity that gives rise to the spatial anisotropy in the velocity-autocorrelation function of the confined fluids. Further, we use the MFE/GLE formulation to extract the thermal force a fluid molecule experiences in a MD simulation. Noise extraction from MD simulation suggests that the frequency distribution of the thermal force is non-Gaussian. Also, the frequency distribution of the thermal force near the confining surface is found to be different in the direction parallel and perpendicular to the confinement. We also use the formulation to compute the noise correlation time of water confined inside a (6,6) carbon-nanotube (CNT). It is observed that inside the (6,6) CNT, in which water arranges itself in a highly concerted single-file arrangement, the correlation time of thermal noise is about an order of magnitude higher than that of bulk water.

The effect of slag addition on strength development of Class C fly ash geopolymer concrete at normal temperature

NASA Astrophysics Data System (ADS)

Wardhono, Arie; Law, David W.; Sutikno, Dani, Hasan

2017-09-01

This paper presents the effect of slag addition on strength development and workability of fly ash/slag based geopolymer (FASLG) concrete cured at normal temperature. Class C fly ash with high ferrite (Fe) content was used as the primary material. The proportions of fly ash (FA) to slag (SL) are: 1 FA : 0 SL, 0.9 FA : 0.1 SL, 0.7 FA : 0.3 SL, and 0.5 FA : 0.5 SL. The workability and strength properties were determined by slump, vikat, and compressive strength tests. The result shows that the highest compressive strength was achieved by FASLG-3 concrete with 30% slag addition and exhibited a comparable strength to that normal concrete at 28 days. The 30% slag addition also improve the workability and increase the setting time of FASLG concrete specimens. It can be concluded that the slag inclusion on fly ash will improve the performance of geopolymer concrete at normal temperature.

Accumulation and depuration of trace metals in Southern Toads, Bufo Terrestris, exposed to coal combustion waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, C.; Hassan, S.; Mendonca, M.

2009-02-15

Accumulation and depuration of metals by an organism are underrepresented in the literature. We collected southern toads (Bufo terrestris) from coal by-product (ash)-contaminated and uncontaminated sites to examine metal concentrations over time. Toads were placed in four exposure regimes, then sacrificed periodically over a 5-month period, and whole-body metal levels were measured. Toads exposed to ash accumulated significant concentrations of metals. Metal concentrations changed throughout the experiment, and profiles of accumulation and depuration differed depending on the metal and exposure regime. Ash-exposed toads exhibited elevated levels of 11 of 18 metals measured. Increases ranged from 47.5% for Pb to moremore » than 5000% for As. Eight of 18 metals did not change in control toads, while 10 of 18 metals decreased in toads removed from ash, ranging from -25% for Co to -96% for Tl. Seven metals that decreased in toads removed from ash did not change in control toads.« less

Co-detoxification of transformer oil-contained PCBs and heavy metals in medical waste incinerator fly ash under sub- and supercritical water.

PubMed

Wang, Chunfeng; Zhu, Nengmin; Wang, Yanmin; Zhang, Fushen

2012-01-17

The simultaneous detoxification processes of transformer oil-contained PCBs and heavy metals in medical waste incinerator (MWI) fly ash were developed under sub- and supercritical water. The addition of MWI fly ash to transformer oil-contained PCBs was found to increase the destruction efficiency of PCBs, at the same time, it facilitated reducing the leaching concentration of toxic metals from residues (obtained after reaction) for harmless disposal. In this study, we elucidated primarily the catalysis possibility of heavy metals in raw MWI fly ash for PCBs degradation by adopting the sequential extraction procedure. For both MWI fly ashes, more than 90% destruction efficiency of PCBs was achieved at ≥375 °C for 30 min, and trichlorobenzene (TCB) existing in the transformer oil was also completely decomposed. The correlation of catalytic performance to PCBs degradation was discussed based on structural characteristics and dechlorinated products. Likewise, such process rendered residues innocuous through supercritical water treatment for reuse or disposal in landfill.

Leaching behaviour of municipal solid waste incineration bottom ash: From granular material to monolithic concrete.

PubMed

Sorlini, Sabrina; Collivignarelli, Maria Cristina; Abbà, Alessandro

2017-09-01

The aim of this work was to assess the leaching behaviour of the bottom ash derived from municipal solid waste incineration (MSWI) used in concrete production. In particular, the release of pollutants was evaluated by the application of different leaching tests, both on granular materials and monolithic samples (concrete mixtures cast with bottom ash). The results confirmed that, according to Italian regulations, unwashed bottom ashes present critical issues for the use as alternative aggregates in the construction sector due to the excessive release of pollutants; instead, the leachate from washed bottom ashes was similar to natural aggregates. The concentration of pollutants in the leachate from concrete mixtures was lower than regulation limits for reuse. The crushing process significantly influenced the release of pollutants: this behaviour was due both to the increase in surface area and the release of contaminants from cement. Moreover, the increase in contact time (up to 64 days) involved more heavy metals to be released.

Comments on "Failures in detecting volcanic ash from a satellite-based technique"

USGS Publications Warehouse

Prata, F.; Bluth, G.; Rose, B.; Schneider, D.; Tupper, A.

2001-01-01

The recent paper by Simpson et al. [Remote Sens. Environ. 72 (2000) 191.] on failures to detect volcanic ash using the 'reverse' absorption technique provides a timely reminder of the danger that volcanic ash presents to aviation and the urgent need for some form of effective remote detection. The paper unfortunately suffers from a fundamental flaw in its methodology and numerous errors of fact and interpretation. For the moment, the 'reverse' absorption technique provides the best means for discriminating volcanic ash clouds from meteorological clouds. The purpose of our comment is not to defend any particular algorithm; rather, we point out some problems with Simpson et al.'s analysis and re-state the conditions under which the 'reverse' absorption algorithm is likely to succeed. ?? 2001 Elsevier Science Inc. All rights reserved.

Microscopic observations of self-healing products in calcareous fly ash mortars.

PubMed

Jóźwiak-Niedźwiedzka, Daria

2015-01-01

The results of microstructural characterization of mortars containing fly ash class C (High Calcium Fly Ash) from combustion of lignite are presented. The evaluation of the microstructure was performed using scanning electron microscope, optical, and confocal microscope. The tested beams were bent till the crack and microcracks opening, which were healed during the different curing time. The results showed that the replacement of cement with fly ash class C influenced the process of crack healing. The addition of HCFA, at both 30% and 60%, speeds up the self-healing process in cracks and particularly in micro-cracks. In the research, the completely filling up of the cracks by new phases has not been observed, only the beginning of such process has been noticed. © 2014 Wiley Periodicals, Inc.

Removal of vertigo blue dyes from Batik textile wastewater by adsorption onto activated carbon and coal bottom ash

NASA Astrophysics Data System (ADS)

Kusmiyati, L., Puspita Adi; Deni, V.; Robi Indra, S.; Islamica, Dlia; Fuadi, M.

2016-04-01

Removal of vertigo blue dye from batik textile wastewater was studied by adsorptionprocess onto activated carbon (AC) and coal bottom ash (CBA).The influence of experimental conditions (pH solution, dye concentration, and contact time) were studied on the both adsorbents. At equilibrium conditions, the data were fitted to Langmuir and Freundlich adsorption models. The maximum adsorption capacity calculated from the Langmuir model for carbon active was 6.29mg/g at pH that found to be considerably higher than that obtained for coal bottom ash 3.72mg/g pH 9. From Freundlich model, the maximum adsorption capacity is less for coal bottom ash (pH 9) than that for carbon active (pH4).

Trapping techniques for emerald ash borer and its introduced parasitoids

Treesearch

Kristopher Abell; Therese M. Poland; Allard Cosse; Leah S. Bauer

2015-01-01

As soon as emerald ash borer (Agrilus planipennis Fairmaire) (EAB) was discovered near Detroit, Michigan, USA, in 2002, surveys were initiated to delimit the extent of the infested area. These initial delimitation surveys were based on visual assessments using external symptoms because at the time no other detection tools were available and nothing...

Academic Self-Handicapping: Relationships with Learning Specific and General Self-Perceptions and Academic Performance over Time

ERIC Educational Resources Information Center

Gadbois, Shannon A.; Sturgeon, Ryan D.

2011-01-01

Background: Academic self-handicapping (ASH) tendencies, strategies students employ that increase their chances of failure on assessments while protecting self-esteem, are correlated with classroom goal structures and to learners' general self-perceptions and learning strategies. In particular, greater ASH is related to poorer academic performance…

The Characteristic and Activation of Mixed Andisol Soil/Bayat Clays/Rice Husk Ash as Adsorbent of Heavy Metal Chromium (Cr)

NASA Astrophysics Data System (ADS)

Pranoto; Sajidan; Suprapto, A.

2017-02-01

Chromium (Cr) concentration in water can be reduced by adsorption. This study aimed to determine the effect of Andisol soil composition/Bayat clay/husk ash, activation temperature and contact time of the adsorption capacity of Cr in the model solution; the optimum adsorption conditions and the effectiveness of ceramic filters and purifiers to reduce contaminant of Cr in the water. The mixture of Andisol soil, Bayat clay, and husk ash is used as adsorbent of metal ion of Cr(III) using batch method. The identification and characterisation of adsorbent was done with NaF test, infrared spectroscopy (FTIR), X-ray diffraction (XRD). Cr metal concentrations were analyzed by atomic absorption spectroscopy. Sorption isotherms determined by Freundlich equation and Langmuir. The optimum conditions of sorption were achieved at 150°C activation temperature, contact time of 30 minutes and a composition Andisol soil / Bayat clay / husk ash by comparison 80/10/10. The results show a ceramic filter effectively reduces total dissolved solids (TDS) and Chromium in the water with the percentage decrease respectively by 75.91% and 9.44%.

Determination of the elastic modulus of fly ash-based stabilizer applied in the trackbed

NASA Astrophysics Data System (ADS)

Lojda, Vít; Lidmila, Martin; Pýcha, Marek

2017-09-01

This paper describes a unique application of a fly ash-based stabilizer in the trackbed of a railway main line. The key goals of the stabilizer application are to protect the subgrade against the ingress of rain water, to increase the frost resistance and to remediate the natural ground constituted of weathered rock. The stabilizer was designed as a mixture of fly ash, generated as a waste material from coal plants, gypsum, calcium oxide and water. The mixture recipe was developed in a laboratory over several years. In 2005, a trial section of a railway line with subgrade consisting of clay limestone (weathered marlite) was built in the municipality of Smiřice. Since then, periodical measurements including collection of samples for laboratory evaluation of the fly ash-based stabilizer have taken place. Over the time span of the measurements, changes in mineral composition and development of fly ash transforming structures leading to the formation of C-A-S-H gel were detected. This paper describes the experimental laboratory investigation of the influence of dynamic loading on the elastic modulus of fly ash stabilizer samples and the development of permanent deformation of the samples with increasing number of loading cycles.

Evaluation of gas-particle partition of dioxins in flue gas I: evaluation of gasification behavior of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans in fly ash by thermal treatment.

PubMed

Yokohama, Naoki; Otaka, Hiroaki; Minato, Ichiro; Nakata, Munetaka

2008-05-01

The gasification behavior of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in fly ash by thermal treatment has been investigated to estimate gas-particle partition in flue gas. The results obtained in thermal experiments under various conditions showed that gasification of PCDD/Fs depends on air flow rate and treatment weight of fly ash as well as treatment temperature. On the other hand, the results obtained in the thermal experiments using dioxin-free fly ash revealed that during thermal treatment, the de novo synthesis, gasification, and decomposition of PCDFs proceeded at different rates. This difference in the reaction rates indicates that thermal treatment time is also a factor in determining the gas-particle partition of PCDD/Fs in fly ash. Therefore, reasonable thermal treatment conditions were established and applied to three ash samples. For all samples, PCDD/Fs started to gasify at 350 degrees C treatment, whereas 53-98% of PCDD/F homologs gasified at 400 degrees C treatment, implying that gaseous PCDD/Fs are dominant in flue gas at temperatures in the range 350-400 degrees C regardless of particle concentration.

Ammonia Inactivation of Ascaris Ova in Ecological Compost by Using Urine and Ash

PubMed Central

Parzen, Rebecca E.; Mercado Guzmán, Álvaro

2012-01-01

Viable ova of Ascaris lumbricoides, an indicator organism for pathogens, are frequently found in feces-derived compost produced from ecological toilets, demonstrating that threshold levels of time, temperature, pH, and moisture content for pathogen inactivation are not routinely met. Previous studies have determined that NH3 has ovicidal properties for pathogens, including Ascaris ova. This research attempted to achieve Ascaris inactivation via NH3 under environmental conditions commonly found in ecological toilets and using materials universally available in an ecological sanitation setting, including compost (feces and sawdust), urine, and ash. Compost mixed with stored urine and ash produced the most rapid inactivation, with significant inactivation observed after 2 weeks and with a time to 99% ovum inactivation (T99) of 8 weeks. Compost mixed with fresh urine and ash achieved a T99 of 15 weeks, after a 4-week lag phase. Both matrices had relatively high total-ammonia concentrations and pH values of >9.24 (pKa of ammonia). In compost mixed with ash only, and in compost mixed with fresh urine only, inactivation was observed after an 11-week lag phase. These matrices contained NH3 concentrations of 164 to 173 and 102 to 277 mg/liter, respectively, when inactivation occurred, which was below the previously hypothesized threshold for inactivation (280 mg/liter), suggesting that a lower threshold NH3 concentration may be possible with a longer contact time. Other significant results include the hydrolysis of urea to ammonia between pH values of 10.4 and 11.6, above the literature threshold pH of 10. PMID:22582051

Ammonia inactivation of Ascaris ova in ecological compost by using urine and ash.

PubMed

McKinley, James W; Parzen, Rebecca E; Mercado Guzmán, Álvaro

2012-08-01

Viable ova of Ascaris lumbricoides, an indicator organism for pathogens, are frequently found in feces-derived compost produced from ecological toilets, demonstrating that threshold levels of time, temperature, pH, and moisture content for pathogen inactivation are not routinely met. Previous studies have determined that NH(3) has ovicidal properties for pathogens, including Ascaris ova. This research attempted to achieve Ascaris inactivation via NH(3) under environmental conditions commonly found in ecological toilets and using materials universally available in an ecological sanitation setting, including compost (feces and sawdust), urine, and ash. Compost mixed with stored urine and ash produced the most rapid inactivation, with significant inactivation observed after 2 weeks and with a time to 99% ovum inactivation (T(99)) of 8 weeks. Compost mixed with fresh urine and ash achieved a T(99) of 15 weeks, after a 4-week lag phase. Both matrices had relatively high total-ammonia concentrations and pH values of >9.24 (pK(a) of ammonia). In compost mixed with ash only, and in compost mixed with fresh urine only, inactivation was observed after an 11-week lag phase. These matrices contained NH(3) concentrations of 164 to 173 and 102 to 277 mg/liter, respectively, when inactivation occurred, which was below the previously hypothesized threshold for inactivation (280 mg/liter), suggesting that a lower threshold NH(3) concentration may be possible with a longer contact time. Other significant results include the hydrolysis of urea to ammonia between pH values of 10.4 and 11.6, above the literature threshold pH of 10.

Distribution and mass of tephra-fall deposits from volcanic eruptions of Sakurajima Volcano based on posteruption surveys

NASA Astrophysics Data System (ADS)

Oishi, Masayuki; Nishiki, Kuniaki; Geshi, Nobuo; Furukawa, Ryuta; Ishizuka, Yoshihiro; Oikawa, Teruki; Yamamoto, Takahiro; Nanayama, Futoshi; Tanaka, Akiko; Hirota, Akinari; Miwa, Takahiro; Miyabuchi, Yasuo

2018-04-01

We estimate the total mass of ash fall deposits for individual eruptions of Sakurajima Volcano, southwest Japan based on distribution maps of the tephra fallout. Five ash-sampling campaigns were performed between 2011 and 2015, during which time Sakurajima continued to emit ash from frequent Vulcanian explosions. During each survey, between 29 and 53 ash samplers were installed in a zone 2.2-43 km downwind of the source crater. Total masses of erupted tephra were estimated using several empirical methods based on the relationship between the area surrounded by a given isopleth and the thickness of ash fall within each isopleth. We obtained 70-40,520 t (4.7 × 10-8-2.7 × 10-5-km3 DRE) as the minimum estimated mass of erupted materials for each eruption period. The minimum erupted mass of tephra produced during the recorded events was calculated as being 890-5140 t (5.9 × 10-7-3.6 × 10-6-km3 DRE). This calculation was based on the total mass of tephra collected during any one eruptive period and the number of eruptions during that period. These values may thus also include the contribution of continuous weak ash emissions before and after prominent eruptions. We analyzed the meteorological effects on ash fall distribution patterns and concluded that the width of distribution area of an ash fall is strongly controlled by the near-ground wind speed. The direction of the isopleth axis for larger masses is affected by the local wind direction at ground level. Furthermore, the wind direction influences the direction of the isopleth axes more at higher altitude. While a second maximum of ash fall can appear, the influence of rain might only affect the finer particles in distal areas.

Ash cloud aviation advisories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sullivan, T.J.; Ellis, J.S.; Schalk, W.W.

1992-06-25

During the recent (12--22 June 1991) Mount Pinatubo volcano eruptions, the US Air Force Global Weather Central (AFGWC) requested assistance of the US Department of Energy`s Atmospheric Release Advisory Capability (ARAC) in creating volcanic ash cloud aviation advisories for the region of the Philippine Islands. Through application of its three-dimensional material transport and diffusion models using AFGWC meteorological analysis and forecast wind fields ARAC developed extensive analysis and 12-hourly forecast ash cloud position advisories extending to 48 hours for a period of five days. The advisories consisted of ``relative`` ash cloud concentrations in ten layers (surface-5,000 feet, 5,000--10,000 feet andmore » every 10,000 feet to 90,000 feet). The ash was represented as a log-normal size distribution of 10--200 {mu}m diameter solid particles. Size-dependent ``ashfall`` was simulated over time as the eruption clouds dispersed. Except for an internal experimental attempt to model one of the Mount Redoubt, Alaska, eruptions (12/89), ARAC had no prior experience in modeling volcanic eruption ash hazards. For the cataclysmic eruption of 15--16 June, the complex three-dimensional atmospheric structure of the region produced dramatically divergent ash cloud patterns. The large eruptions (> 7--10 km) produced ash plume clouds with strong westward transport over the South China Sea, Southeast Asia, India and beyond. The low-level eruptions (< 7 km) and quasi-steady-state venting produced a plume which generally dispersed to the north and east throughout the support period. Modeling the sequence of eruptions presented a unique challenge. Although the initial approach proved viable, further refinement is necessary and possible. A distinct need exists to quantify eruptions consistently such that ``relative`` ash concentrations relate to specific aviation hazard categories.« less

Issuance of Volcanic Ash Advisories: Washington VAAC Perspective

NASA Astrophysics Data System (ADS)

Salemi, A.; Ruminski, M. G.

2011-12-01

In the event of a volcanic eruption, one of the nine Volcanic Ash Advisory Centers (VAAC) across the globe is responsible for issuing a Volcanic Ash Advisory (VAA). The VAA contains information about which volcano is erupting, the volcanoes location, as well as the time and duration of the eruption. If ash is observed in satellite imagery, a 6, 12 and 18 hour forecast are provided to specify the possible location of ash. The goal of the VAA is to help airlines create accurate flight guidance for their aircraft. The priority of each VAAC is to prevent aircraft from flying through ash with a secondary priority of minimizing unnecessary diversions. Remote sensing platforms provide a unique perspective for volcanic ash detection especially in the cases of remote and unmonitored volcanoes. This includes monitoring of multispectral satellite imagery (Visible, Infrared) from both geostationary and polar orbiting platforms as well as derived products such as SO2, Volcanic Ash Masks/Loading and LIDAR data. To generate the VAA, satellite analysts use the satellite imagery in combination with observations from local Meteorological Watch Offices (MWO), Volcano Observatories, Pilot Reports (PIREP), seismic stations, web cameras and meteorological forecast grids. Challenges arise in regard to availability of data for each individual volcano, reliability of model wind fields over data sparse regions, as well as timeliness and availability of satellite imagery and products. These challenges become further exacerbated when volcanic ash crosses VAAC and MWO boundaries and interagency communication becomes essential. While working through multi-lingual communications and operational variation (e.g. data availability, standard operation procedures), VAACs face the challenge of maintaining coordination and avoiding the pitfalls of break downs in communication and guidance confusion. This talk will discuss these issues and pose potential communication and coordination efforts from the Washington VAAC perspective.

Effects of trap type, placement and ash distribution on emerald ash borer captures in a low density site.

PubMed

McCullough, Deborah G; Siegert, Nathan W; Poland, Therese M; Pierce, Steven J; Ahn, Su Zie

2011-10-01

Effective methods for early detection of newly established, low density emerald ash borer (Agrilus planipennis Fairmaire) infestations are critically needed in North America. We assessed adult A. planipennis captures on four types of traps in a 16-ha site in central Michigan. The site was divided into 16 blocks, each comprised of four 50- by 50-m cells. Green ash trees (Fraxinus pennsylvanica Marshall) were inventoried by diameter class and ash phloem area was estimated for each cell. One trap type was randomly assigned to each cell in each block. Because initial sampling showed that A. planipennis density was extremely low, infested ash logs were introduced into the center of the site. In total, 87 beetles were captured during the summer. Purple double-decker traps baited with a blend of ash leaf volatiles, Manuka oil, and ethanol captured 65% of all A. planipennis beetles. Similarly baited, green double-decker traps captured 18% of the beetles, whereas sticky bands on girdled trees captured 11% of the beetles. Purple traps baited with Manuka oil and suspended in the canopies of live ash trees captured only 5% of the beetles. At least one beetle was captured on 81% of the purple double-decker traps, 56% of the green double-decker traps, 42% of sticky bands, and 25% of the canopy traps. Abundance of ash phloem near traps had no effect on captures and trap location and sun exposure had only weak effects on captures. Twelve girdled and 29 nongirdled trees were felled and sampled in winter. Current-year larvae were present in 100% of the girdled trees and 72% of the nongirdled trees, but larval density was five times higher on girdled than nongirdled trees.

Pathways to ambulatory sensitive hospitalisations for Māori in the Auckland and Waitemata regions.

PubMed

Barker, Carol; Crengle, Sue; Bramley, Dale; Bartholomew, Karen; Bolton, Patricia; Walsh, Michael; Wignall, Jean

2016-10-28

Ambulatory Sensitive Hospitalisations (ASH) are a group of conditions potentially preventable through interventions delivered in the primary health care setting. ASH rates are consistently higher for Māori compared with non-Māori. This study aimed to establish Māori experience of factors driving the use of hospital services for ASH conditions, including barriers to accessing primary care. A telephone questionnaire exploring pathways to ASH was administered to Māori (n=150) admitted to Auckland and Waitemata District Health Board (DHB) hospitals with an ASH condition between January 1st-June 30th 2015. A cohort of 1,013 participants were identified; 842 (83.1%) were unable to be contacted. Of the 171 people contactable, 150 agreed to participate, giving an overall response rate of 14.8% and response rate of contactable patients of 87.7%. Results demonstrated high rates of self-reported enrolment, utilisation and preference for primary care. Many participants demonstrated appropriate health seeking behaviour and accurate recall of diagnoses. While financial barriers to accessing primary care were reported, non-financial barriers including lack of after-hours provision (12.6% adults, 37.7% children), appointment availability (7.4% adults, 17.0% children) and lack of transport (13.7% adults, 20.8% children) also featured in participant responses. Interventions to reduce Māori ASH include: timely access to primary care through electronic communications, increased appointment availability, extended opening hours, low cost after-hours care and consistent best management of ASH conditions in general practice through clinical pathways. Facilitated enrolment of ASH patients with no general practitioner could also reduce ASH. Research into transport barriers and enablers for Māori accessing primary care is required to support future interventions.

Effect of time on dyeing wastewater treatment

NASA Astrophysics Data System (ADS)

Ye, Tingjin; Chen, Xin; Xu, Zizhen; Chen, Xiaogang; Shi, Liang; He, Lingfeng; Zhang, Yongli

2018-03-01

The preparation of carboxymethylchitosan wrapping fly-ash adsorbent using high temperature activated fly ash and sodium carboxymethyl chitosan (CWF), as with the iron-carbon micro-electrolysis process simulation and actual printing and dyeing wastewater. The effects of mixing time and static time on decolorization ratio, COD removing rate and turbidness removing rate were investigated. The experimental results show that the wastewater stirring times on the decolorization rate and COD removal rate and turbidity removal rate influence, with increasing of the stirring time, three showed a downward trend, and reached the peak at 10 min time; wastewater time on the decolorization ratio and COD removing efficiency and turbidness removing rate influence, along with standing time increase, three who declined and reached the maximum in 30min time.

Daughter-Specific Transcription Factors Regulate Cell Size Control in Budding Yeast

PubMed Central

Di Talia, Stefano; Wang, Hongyin; Skotheim, Jan M.; Rosebrock, Adam P.; Futcher, Bruce; Cross, Frederick R.

2009-01-01

In budding yeast, asymmetric cell division yields a larger mother and a smaller daughter cell, which transcribe different genes due to the daughter-specific transcription factors Ace2 and Ash1. Cell size control at the Start checkpoint has long been considered to be a main regulator of the length of the G1 phase of the cell cycle, resulting in longer G1 in the smaller daughter cells. Our recent data confirmed this concept using quantitative time-lapse microscopy. However, it has been proposed that daughter-specific, Ace2-dependent repression of expression of the G1 cyclin CLN3 had a dominant role in delaying daughters in G1. We wanted to reconcile these two divergent perspectives on the origin of long daughter G1 times. We quantified size control using single-cell time-lapse imaging of fluorescently labeled budding yeast, in the presence or absence of the daughter-specific transcriptional regulators Ace2 and Ash1. Ace2 and Ash1 are not required for efficient size control, but they shift the domain of efficient size control to larger cell size, thus increasing cell size requirement for Start in daughters. Microarray and chromatin immunoprecipitation experiments show that Ace2 and Ash1 are direct transcriptional regulators of the G1 cyclin gene CLN3. Quantification of cell size control in cells expressing titrated levels of Cln3 from ectopic promoters, and from cells with mutated Ace2 and Ash1 sites in the CLN3 promoter, showed that regulation of CLN3 expression by Ace2 and Ash1 can account for the differential regulation of Start in response to cell size in mothers and daughters. We show how daughter-specific transcriptional programs can interact with intrinsic cell size control to differentially regulate Start in mother and daughter cells. This work demonstrates mechanistically how asymmetric localization of cell fate determinants results in cell-type-specific regulation of the cell cycle. PMID:19841732

Photogrammetric retrieval of volcanic ash cloud top height from SEVIRI and MODIS

NASA Astrophysics Data System (ADS)

Zakšek, Klemen; Hort, Matthias; Zaletelj, Janez; Langmann, Bärbel

2013-04-01

Even if erupting in remote areas, volcanoes can have a significant impact on the modern society due to volcanic ash dispersion in the atmosphere. The ash does not affect merely air traffic - its transport in the atmosphere and its deposition on land and in the oceans may also significantly influence the climate through modifications of atmospheric CO2. The emphasis of this contribution is the retrieval of volcanic ash plume height (ACTH). ACTH is important information especially for air traffic but also to predict ash transport and to estimate the mass flux of the ejected material. ACTH is usually estimated from ground measurements, pilot reports, or satellite remote sensing. But ground based instruments are often not available at remote volcanoes and also the pilots reports are a matter of chance. Volcanic ash cloud top height (ACTH) can be monitored on the global level using satellite remote sensing. The most often used method compares brightness temperature of the cloud with the atmospheric temperature profile. Because of uncertainties of this method (unknown emissivity of the ash cloud, tropopause, etc.) we propose photogrammetric methods based on the parallax between data retrieved from geostationary (SEVIRI) and polar orbiting satellites (MODIS). The parallax is estimated using automatic image matching in three level image pyramids. The procedure works well if the data from both satellites are retrieved nearly simultaneously. MODIS does not retrieve the data at exactly the same time as SEVIRI. To compensate for advection we use two sequential SEVIRI images (one before and one after the MODIS retrieval) and interpolate the cloud position from SEVIRI data to the time of MODIS retrieval. ACTH is then estimated by intersection of corresponding lines-of-view from MODIS and interpolated SEVIRI data. The proposed method was tested using MODIS band 1 and SEVIRI HRV band for the case of the Eyjafjallajökull eruption in April 2010. The parallax between MODIS and SEVIRI data can reach over 30 km which implies ACTH of more than 12 km. The accuracy of ACTH was estimated to 0.6 km. The limitation of this procedure is that it has difficulties with automatic image matching if the ash cloud is not opaque.

Experimental confirmation of stable, small-debye-length, pure-electron-plasma equilibria in a stellarator.

PubMed

Kremer, J P; Pedersen, T Sunn; Lefrancois, R G; Marksteiner, Q

2006-09-01

The creation of the first small-Debye length, low temperature pure electron plasmas in a stellarator is reported. A confinement time of 20 ms has been measured. The long confinement time implies the existence of macroscopically stable equilibria and that the single particle orbits are well confined despite the lack of quasisymmetry in the device, the Columbia non-neutral torus. This confirms the beneficial confinement effects of strong electric fields and the resulting rapid E x B rotation of the electrons. The particle confinement time is presently limited by the presence of bulk insulating materials in the plasma, rather than any intrinsic plasma transport processes. A nearly flat temperature profile is seen in the inner part of the plasma.

Ash resuspension related to the 2011-2012 Cordón Caulle eruption, Chile, in a rural community of Patagonia, Argentina

NASA Astrophysics Data System (ADS)

Forte, Pablo; Domínguez, Lucia; Bonadonna, Costanza; Gregg, Chris E.; Bran, Donaldo; Bird, Deanne; Castro, Jonathan M.

2018-01-01

The 2011-2012 Cordón Caulle eruption emitted about 1 km3 of rhyodacitic tephra. Dominant westerly winds in the region caused most of the primary tephra to deposit in neighboring Argentina. In addition to the impact of widespread dispersal and fallout of primary tephra during the eruption, Argentina was also significantly affected by remobilization of the primary ash even several years after the climactic phase of the eruption. In this mixed methods study, we combine aspects of natural and social sciences to characterize the ash resuspension events associated with the 2011-2012 Cordón Caulle deposits and assess the impacts on the Argentinian farming community of Ingeniero Jacobacci in the Patagonian Steppe. Our findings show the primary importance of wind, rainfall and ash availability in controlling the occurrence and persistence of ash resuspension events. The role played by these variables was also reflected in the seasonal distribution of events observed. Regarding the impacts, our results complement those of earlier studies and demonstrate that ash resuspension events can exacerbate the negative impact of primary tephra fallout events from the time of deposition to many years after the eruption. Only after five years has the environment and the farming community begun to show signs of recovery. Our findings also highlight the importance of assessing ash resuspension events in multi-hazard scenarios involving volcanic and hydrometeorologic hazards.

The Pearlette family ash beds in the Great Plains: Finding their identities and their roots in the Yellowstone country

USGS Publications Warehouse

Wilcox, R.E.; Naeser, C.W.

1992-01-01

For many years the numerous deposits of so-called 'Pearlette volcanic ash' in the Great Plains region of the United States were considered to be the remnants of the same volcanic event, and were used as a time-stratigraphic marker of probable Middle Pleistocene age. Although a few early workers had suggested that more than one air-fall event might be represented among the Pearlette occurrences, it was not until the latter half of the present century, after identification of volcanic ash beds by detailed chemical and mineralogical methods had been developed, that it could be established that the 'Pearlette family' of volcanic ashes included three ash beds of subtly differing characteristics. Development of isotopic methods of age determination has established that the ages of the three are significantly different (2.09, 1.29, and 0.60 Ma). The area of distribution of the Pearlette family ash beds was found to include not only the Great Plains, but also to extend across the Rocky Mountain and the Basin and Range provinces to the Pacific Ocean. The search for the sources of these three similar appearing ash beds, facilitated greatly by information gained from concurrent mapping projects underway in areas of major Late Cenozoic volcanic activity in western United States, ultimately led to the sites of the caldera-forming eruptions in the Yellowstone National Park region. ?? 1992.

[Volatile ashes and their biological effect. 2. Fibrogenic effect of volatile ashes].

PubMed

Woźniak, H; Wiecek, E; Lao, I; Wojtczak, J

1989-01-01

In experiments on white Wistar rats fibrogenic effects of 6 samples of fly-ashes collected from electric precipitators in power engineering plants have been evaluated. The coal came from different national deposits. All the ashes have been found to contain: quartz and mullite, 3 ashes contained additionally orthoclase, whereas 1, apart from quartz and mullite, contained kaolinite; naturally radioactive elements (Ra226, K40, Th228) and trace elements (As, Ba, Be, Cd, Ce, Cu, Fe, Pa, Mo, Ni, Pb, Se, U Zu). Experimental pneumoconiosis was induced through intratracheal administration of single doses of 50 mg of dust; the experiment was carried out at 3 time intervals of 3, 6 and 9 months. The fibrogenic activity was evaluated both qualitatively (histopathological methods) and quantitatively (lung weight, hydroxyproline content in lungs, dust elimination from lungs); control groups consisted of animals which obtained NaCl solution and quartz sands. Fly-ashes were found to exhibit different fibrogenic effects, yet, their fibrogenic activity was weaker, compared to quartz sands. No clear correlation was found between fibrogenic effects of ashes and test physico-chemical properties, such as the content of SiO2, trace elements or naturally radioactive elements. Analysis of occupational diseases (for the period section): (1979-1983) demonstrated occupational diseases of dust-related aetiology among power engineering workers, pneumoconioses, constituting 7.8% of 127 cases of occupational diseases.

Mercury in coals and fly ashes from Republika and Bobov dol thermoelectric power plants

USGS Publications Warehouse

Kostova, I.; Vassileva, C.; Hower, J.; Mastalerz, Maria; Vassilev, S.; Nikolova, N.

2011-01-01

Feed coal and y ash samples were collected at Republika and Bobov Dol thermoelectric power plants (TPPs). The y ashes (FAs) were collected fromthree rows of the hot-side electrostatic precipitators (ESPs) array. Each sam- ple was wet-screened at 100, 200, 325 and 500 mesh. The coals and y ashes were characterized with regard to their petrological and chemical composition (including mercury content) and to their surface area properties. The calculated enrichment factor (EF) shows that the Hg concentrations in the bulk coal samples from Republika and Bobov Dol TPPs are 2.19 and 1.41, respectively. In some coal size fractions the EF can be up to 4 times higher than the Clarke value. The calculated EF for fly ashes shows that the Hg concentrations in the bulk samples studied are lower (between 0.03 and 0.32) than the Clarke value. The most enriched in Hg are the fly ashes from the 3rd ESP row of Republika TPP. The Hg distribution in bulk FAs taken from dierent rows of the electrostatic precipitators of both TPPs studied shows well established tendency of gradual increase in the Hg content from the 1st to the 2nd and 3rd ESP rows. The correlation between Hg content and surface area, mesopore and micropore volume of y ashes was also done in the present investigation.

Naturally occurring radioactive materials (NORMs) generated from lignite-fired power plants in Kosovo.

PubMed

Hasani, F; Shala, F; Xhixha, G; Xhixha, M K; Hodolli, G; Kadiri, S; Bylyku, E; Cfarku, F

2014-12-01

The energy production in Kosovo depends primarily on lignite-fired power plants. During coal combustion, huge amounts of fly ash and bottom ash are generated, which may result in enriched natural radionuclides; therefore, these radionuclides need to be investigated to identify the possible processes that may lead to the radiological exposure of workers and the local population. Lignite samples and NORMs of fly ash and bottom ash generated in lignite-fired power plants in Kosovo are analyzed using a gamma-ray spectrometry method for the activity concentration of natural radionuclides. The average activity concentrations of (40)K, (226)Ra and (232)Th in lignite are found to be 36 ± 8 Bq kg(-1), 9 ± 1 Bq kg(-1) and 9 ± 3 Bq kg(-1), respectively. Indications on the occurrence and geochemical behavior of uranium in the lignite matrix are suggested. The activity concentrations of natural radionuclides in fly ash and bottom ash samples are found to be concentrated from 3 to 5 times that of the feeding lignite. The external gamma-ray absorbed dose rate and the activity concentration index are calculated to assess the radiological hazard arising from ash disposal and recycling in the cement industry. Copyright © 2014 Elsevier Ltd. All rights reserved.

A new natural hazards data-base for volcanic ash and SO2 from global satellite remote sensing measurements

NASA Astrophysics Data System (ADS)

Stebel, Kerstin; Prata, Fred; Theys, Nicolas; Tampellini, Lucia; Kamstra, Martijn; Zehner, Claus

2014-05-01

Over the last few years there has been a recognition of the utility of satellite measurements to identify and track volcanic emissions that present a natural hazard to human populations. Mitigation of the volcanic hazard to life and the environment requires understanding of the properties of volcanic emissions, identifying the hazard in near real-time and being able to provide timely and accurate forecasts to affected areas. Amongst the many ways to measure volcanic emissions, satellite remote sensing is capable of providing global quantitative retrievals of important microphysical parameters such as ash mass loading, ash particle effective radius, infrared optical depth, SO2 partial and total column abundance, plume altitude, aerosol optical depth and aerosol absorbing index. The eruption of Eyjafjallajökull in April May, 2010 led to increased research and measurement programs to better characterize properties of volcanic ash and the need to establish a data-base in which to store and access these data was confirmed. The European Space Agency (ESA) has recognized the importance of having a quality controlled data-base of satellite retrievals and has funded an activity called Volcanic Ash Strategic Initiative Team VAST (vast.nilu.no) to develop novel remote sensing retrieval schemes and a data-base, initially focused on several recent hazardous volcanic eruptions. In addition, the data-base will host satellite and validation data sets provided from the ESA projects Support to Aviation Control Service SACS (sacs.aeronomie.be) and Study on an end-to-end system for volcanic ash plume monitoring and prediction SMASH. Starting with data for the eruptions of Eyjafjallajökull, Grímsvötn, and Kasatochi, satellite retrievals for Puyhue-Cordon Caulle, Nabro, Merapi, Okmok, Kasatochi and Sarychev Peak will eventually be ingested. Dispersion model simulations are also being included in the data-base. Several atmospheric dispersion models (FLEXPART, SILAM and WRF-Chem) are used in VAST to simulate the dispersion of volcanic ash and SO2 emitted during an eruption. Source terms and dispersion model results will be given. In time, data from conventional in situ sampling instruments, airborne and ground-based remote sensing platforms and other meta-data (bulk ash and gas properties, volcanic setting, volcanic eruption chronologies, potential impacts etc.) will be added. Important applications of the data-base are illustrated related to the ash/aviation problem and to estimating SO2 fluxes from active volcanoes-as a means to diagnose future unrest. The data-base has the potential to provide the natural hazards community with a dynamic atmospheric volcanic hazards map and will be a valuable tool particularly for aviation.

Alpha Channeling in Open-System Magnetic Devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fisch, Nathaniel

The Grant DE-SC0000736, Alpha Channeling in Open-System Magnetic Devices, is a continuation of the Grant DE-FG02-06ER54851, Alpha Channeling in Mirror Machines. In publications funded by DE-SC0000736, the grant DE-FG02-06ER54851 was actually credited. The key results obtained under Grant DE-SC0000736, Alpha Channeling in Open-System Magnetic Devices, appear in a series of publications. The earlier effort under DE-FG02- 06ER54851 was the subject of a previous Final Report. The theme of this later effort has been unusual confinement effects, or de-confinement effects, in open-field magnetic confinement devices. First, the possibilities in losing axisymmetry were explored. Then a number of issues in rotating plasmamore » were addressed. Most importantly, a spinoff application to plasma separations was recognized, which also resulted in a provisional patent application. (That provisional patent application, however, was not pursued further.) Alpha channeling entails injecting waves into magnetically confined plasma to release energy from one particular ion while ejecting that ion. The ejection of the ion is actually a concomitant effect in releasing energy from the ion to the wave. In rotating plasma, there is the opportunity to store the energy in a radial electric field rather than in waves. In other words, the ejected alpha particle loses its energy to the radial potential, which in turn produces plasma rotation. This is a very useful effect, since producing radial electric fields by other means are technologically more difficult. In fact, one can heat ions, and then eject them, to produce the desired radial field. In each case, there is a separation effect of different ions, which generalizes the original alpha-channeling concept of separating alpha ash from hydrogen. In a further generalization of the separation concept, a double-well filter represents a new way to produce high-throughput separations of ions, potentially useful for nuclear waste remediation.« less

Analysis of the 2006 block-and-ash flow deposits of Merapi Volcano, Java, Indonesia, using high-spatial resolution IKONOS images and complementary ground based observations

NASA Astrophysics Data System (ADS)

Thouret, Jean-Claude; Gupta, Avijit; Liew, Soo Chin; Lube, Gert; Cronin, Shane J.; Surono, Dr

2010-05-01

On 16 June 2006 an overpass of IKONOS coincided with the emplacement of an active block-and-ash flow fed by a lava dome collapse event at Merapi Volcano (Java, Indonesia). This was the first satellite image recorded for a moving pyroclastic flow. The very high-spatial resolution data displayed the extent and impact of the pyroclastic deposits emplaced during and prior to, the day of image acquisition. This allowed a number of features associated with high-hazard block-and-ash flows emplaced in narrow, deep gorges to be mapped, interpreted and understood. The block-and-ash flow and surge deposits recognized in the Ikonos images include: (1) several channel-confined flow lobes and tongues in the box-shaped valley; (2) thin ash-cloud surge deposit and knocked-down trees in constricted areas on both slopes of the gorge; (3) fan-like over bank deposits on the Gendol-Tlogo interfluves from which flows were re-routed in the Tlogo secondary valley; (4) massive over bank lobes on the right bank from which flows devastated the village of Kaliadem 0.5 km from the main channel, a small part of this flow being re-channeled in the Opak secondary valley. The high-resolution IKONOS images also helped us to identify geomorphic obstacles that enabled flows to ramp and spill out from the sinuous channel, a process called flow avulsion. Importantly, the avulsion redirected flows to unexpected areas away from the main channel. In the case of Merapi we see that the presence of valley fill by previous deposits, bends and man-made dams influence the otherwise valley-guided course of the flows. Sadly, Sabo dams (built to ameliorate the effect of high sediment load streams) can actually cause block-and-ash flows to jump out of their containing channel and advance into sensitive areas. Very-high-spatial resolution satellite images are very useful for mapping and interpreting the distribution of freshly erupted volcanic deposits. IKONOS-type images with 1-m resolution provide opportunities to study and map the meter-scale detail of volcanic deposits. When such high-spatial-resolution satellite remote sensing data are combined with in situ field work, geomorphic analyses can be applied that allow us to more fully understand the dynamics and hazards of eruptions. In the case given here, IKONOS imagery allowed two qualitative hazard assessments for block-and-ash flow activity in drainages around Merapi. Firstly, the interpretation of IKONOS images provides insights in factors that control the propagation of secondary flows as the avulsion of the main flows is driven by longitudinal change in channel capacity due to increased sinuosity in the valley and decreased containment space. Secondly, the sinuosity and obstacles (including Sabo dams) may create over bank flows over adjacent low relief, allowing them to reach unexpectedly vulnerable areas distant from an active dome and away from the volcanically active valleys. Hazard assessment should therefore consider the geometry of secondary channels outside the principal valleys.

Ash Plume from Shiveluch

NASA Image and Video Library

2012-10-09

When NASA’s Terra satellite passed over Russia’s Kamchatka Peninsula at noon local time (00:00 Universal Time) on October 6, 2012, Shilveluch Volcano was quiet. By the time NASA’s Aqua satellite passed over the area two hours later (bottom image), the volcano had erupted and sent a plume of ash over the Kamchatskiy Zaliv. The plume traveled about 90 kilometers (55 miles) toward the south-southeast, where a change in wind direction began pushing the plume toward the east. On October 6, 2012, the Kamchatka Volcanic Emergency Response Team (KVERT) reported that the ash plume from Shiveluch reached an altitude of 3 kilometers (9,800 feet) above sea level, and had traveled some 220 kilometers (140 miles) from the volcano summit. Shiveluch (also spelled Sheveluch) ranks among the biggest and most active volcanoes on the Kamchatka Peninsula. Rising to 3,283 meters (10,771 feet) above sea level, Shiveluch is a stratovolcano composed of alternating layers of hardened lava, compacted ash, and rocks ejected by previous eruptions. The beige-colored expanse of rock on the volcano’s southern slopes (visible in both images) is due to an explosive eruption that occurred in 1964. Part of Shiveluch’s southern flank collapsed, and the light-colored rock is avalanche debris left by that event. High-resolution imagery of Shiveluch shows very little vegetation within that avalanche zone. On October 6, 2012, KVERT cited observations from the Moderate Resolution Imaging Spectroradiometer (MODIS) instruments on Terra and Aqua in detecting the Shiveluch eruption. This was not the first time that MODIS observed a Shiveluch eruption shortly after it started. In 2007, MODIS captured an image within minutes of the eruption’s start, before winds could blow the ash away from the summit. When NASA’s Terra satellite passed over Russia’s Kamchatka Peninsula at noon local time (00:00 Universal Time) on October 6, 2012, Shilveluch Volcano was quiet (top image). By the time NASA’s Aqua satellite passed over the area two hours later (bottom image), the volcano had erupted and sent a plume of ash over the Kamchatskiy Zaliv. The plume traveled about 90 kilometers (55 miles) toward the south-southeast, where a change in wind direction began pushing the plume toward the east. On October 6, 2012, the Kamchatka Volcanic Emergency Response Team (KVERT) reported that the ash plume from Shiveluch reached an altitude of 3 kilometers (9,800 feet) above sea level, and had traveled some 220 kilometers (140 miles) from the volcano summit. Shiveluch (also spelled Sheveluch) ranks among the biggest and most active volcanoes on the Kamchatka Peninsula. Rising to 3,283 meters (10,771 feet) above sea level, Shiveluch is a stratovolcano composed of alternating layers of hardened lava, compacted ash, and rocks ejected by previous eruptions. The beige-colored expanse of rock on the volcano’s southern slopes (visible in both images) is due to an explosive eruption that occurred in 1964. Part of Shiveluch’s southern flank collapsed, and the light-colored rock is avalanche debris left by that event. High-resolution imagery of Shiveluch shows very little vegetation within that avalanche zone. On October 6, 2012, KVERT cited observations from the Moderate Resolution Imaging Spectroradiometer (MODIS) instruments on Terra and Aqua in detecting the Shiveluch eruption. This was not the first time that MODIS observed a Shiveluch eruption shortly after it started. In 2007, MODIS captured an image within minutes of the eruption’s start, before winds could blow the ash away from the summit. Credit: NASA Earth Observatory NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Early evolution of a stratospheric volcanic eruption cloud as observed with TOMS and AVHRR

USGS Publications Warehouse

Schneider, D.J.; Rose, William I.; Coke, L.R.; Bluth, G.J.S.; Sprod, I.E.; Krueger, A.J.

1999-01-01

This paper is a detailed study of remote sensing data from the total ozone mapping spectrometer (TOMS) and the advanced very high resolution radiometer (AVHRR) satellite detectors, of the 1982 eruption of El Chichón, Mexico. The volcanic cloud/atmosphere interactions in the first four days of this eruption were investigated by combining ultraviolet retrievals to estimate the mass of sulfur dioxide in the volcanic cloud [Krueger et al., 1995] with thermal infrared retrievals of the size, optical depth, and mass of fine-grained (1–10 μm radius) volcanic ash [Wen and Rose, 1994]. Our study provides the first direct evidence of gravitational separation of ash from a stratospheric, gas-rich, plinian eruption column and documents the marked differences in residence times of volcanic ash and sulfur dioxide in volcanic clouds. The eruption column reached as high as 32 km [Carey and Sigurdsson, 1986] and was injected into an atmosphere with a strong wind shear, which allowed for an observation of the separation of sulfur dioxide and volcanic ash. The upper, more sulfur dioxide-rich part of the cloud was transported to the west in the stratosphere, while the fine-grained ash traveled to the south in the troposphere. The mass of sulfur dioxide released was estimated at 7.1 × 109 kg with the mass decreasing by approximately 4% 1 day after the peak. The mass of fine-grained volcanic ash detected was estimated at 6.5 × 109 kg, amounting to about 0.7% of the estimated mass of the ash which fell out in the mapped ash blanket close to the volcano. Over the following days, 98% of this remaining fine ash was removed from the volcanic cloud, and the effective radius of ash in the volcanic cloud decreased from about 8 μm to about 4 μm.

RARE EARTH ELEMENTS IN FLY ASHES AS POTENTIAL INDICATORS OF ANTHROPOGENIC SOIL CONTAMINATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattigod, Shas V.

2003-08-01

Studies of rare earth element (REE) content of disposed fly ashes and their potential mobility were neglected for decades because these elements were believed to be environmentally benign. A number of recent studies have now shown that REE may pose a long-term risk to the biosphere. Therefore, there is a critical need to study the REE concentrations in fly ash and their potential mobilization and dispersal upon disposal in the environment. We analyzed the REE content of bulk, size fractionated, and density separated fractions of three fly ash samples derived from combustion of sub bituminous coals from the western Unitedmore » States and found that the concentrations of these elements in bulk ashes were within the range typical of fly ashes derived from coals from the North American continent. The concentrations of light rare earth elements (LREE) such as La, Ce, and Nd, however, tended towards the higher end of the concentration range whereas, the concentrations of middle rare earth elements (MREE) (Sm and Eu) and heavy rare earth elements (HREE) (Lu) were closer to the lower end of the observed range for North American fly ashes. The concentrations of REE did not show any significant enrichment with decreasing particle size, this is typical of nonvolatile lithophilic element behavior during the combustion process. The lithophilic nature of REE was also confirmed by their concentrations in heavy density fractions of these fly ashes being on average about two times more enriched than the concentrations in the light density fractions. Shale normalized average of REE concentrations of fly ashes and coals revealed significant positive anomalies for Eu and Dy. Because of these distinctive positive anomalies of Eu and Dy, we believe that fly ash contamination of soils can be fingerprinted and distinguished from other sources of anthropogenic REE inputs in to the environment.« less

Effect of rice husk ash mass on sustainability pyrolysis zone of fixed bed downdraft gasifier with capacity of 10 kg/hour

NASA Astrophysics Data System (ADS)

Surjosatyo, Adi; Haq, Imaduddin; Dafiqurrohman, Hafif; Gibran, Felly Rihlat

2017-03-01

The formation of pyrolysis sustainability (Sustainable Pyrolysis) is the objective of the gasification process. Pyrolysis zone in the gasification process is the result of the endothermic reaction that get heat from oxidation (combustion) of the fuel with oxygen, where cracking biomass rice husk result of such as charcoal, water vapor, steam tar, and gas - gas (CO, H 2, CH 4, CO 2 and N 2) and must be maintained at a pyrolysis temperature to obtain results plentiful gas (producer gas) or syngas (synthetic gas). Obtaining continuously syngas is indicated by flow rate (discharge) producer gas well and the consistency of the flame on the gas burner, it is highly influenced by the gasification process and the operation of the gasifier and the mass balance (mass balance) between the feeding rate of rice husk with the disposal of ash (ash removal). In experiments conducted is using fixed bed gasifier type downdraft capacity of 10 kg/h. Besides setting the mass of rice husks into the gasifier and disposal arrangements rice husk ash may affect the sustainability of the pyrolysis process, but tar produced during the gasification process causes sticky rice husk ash in the plenum gasifier. Modifications disposal system rice husk ash can facilitate the arrangement of ash disposal then could control the temperature pyrolysis with pyrolysis at temperatures between 500-750 ° C. The experimental study was conducted to determine the effect of mass quantities of rice husk ash issued against sustainability pyrolysis temperature which is obtained at each time disposal of rice husk ash to produce 60-90 grams of ash issued. From some experimental phenomena is expected to be seen pyrolysis and its effect on the flow rate of syngas and the stability of the flame on the gas burner so that this research can find a correlation to obtain performance (performance) gasifier optimal.

Early evolution of a stratospheric volcanic eruption cloud as observed with TOMS and AVHRR

NASA Astrophysics Data System (ADS)

Schneider, David J.; Rose, William I.; Coke, Larry R.; Bluth, Gregg J. S.; Sprod, Ian E.; Krueger, Arlin J.

1999-02-01

This paper is a detailed study of remote sensing data from the total ozone mapping spectrometer (TOMS) and the advanced very high resolution radiometer (AVHRR) satellite detectors, of the 1982 eruption of El Chichón, Mexico. The volcanic cloud/atmosphere interactions in the first four days of this eruption were investigated by combining ultraviolet retrievals to estimate the mass of sulfur dioxide in the volcanic cloud [Krueger et al., 1995] with thermal infrared retrievals of the size, optical depth, and mass of fine-grained (1-10 μm radius) volcanic ash [Wen and Rose, 1994]. Our study provides the first direct evidence of gravitational separation of ash from a stratospheric, gas-rich, plinian eruption column and documents the marked differences in residence times of volcanic ash and sulfur dioxide in volcanic clouds. The eruption column reached as high as 32 km [Carey and Sigurdsson, 1986] and was injected into an atmosphere with a strong wind shear, which allowed for an observation of the separation of sulfur dioxide and volcanic ash. The upper, more sulfur dioxide-rich part of the cloud was transported to the west in the stratosphere, while the fine-grained ash traveled to the south in the troposphere. The mass of sulfur dioxide released was estimated at 7.1 × 109 kg with the mass decreasing by approximately 4% 1 day after the peak. The mass of fine-grained volcanic ash detected was estimated at 6.5 × 109 kg, amounting to about 0.7% of the estimated mass of the ash which fell out in the mapped ash blanket close to the volcano. Over the following days, 98% of this remaining fine ash was removed from the volcanic cloud, and the effective radius of ash in the volcanic cloud decreased from about 8 μm to about 4 μm.

Generation and distribution of PAHs in the process of medical waste incineration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Ying, E-mail: echochen327@163.com; National Center of Solid Waste Management, Ministry of Environmental Protection, Beijing 100029; Zhao, Rongzhi

Highlights: ► PAHs generation and distribution features of medical waste incineration are studied. ► More PAHs were found in fly ash than that in bottom ash. ► The highest proportion of PAHs consisted of the seven most carcinogenic ones. ► Increase of free oxygen molecule and burning temperature promote PAHs degradation. ► There is a moderate positive correlation between total PCDD/Fs and total PAHs. - Abstract: After the deadly earthquake on May 12, 2008 in Wenchuan county of China, several different incineration approaches were used for medical waste disposal. This paper investigates the generation properties of polycyclic aromatic hydrocarbons (PAHs)more » during the incineration. Samples were collected from the bottom ash in an open burning slash site, surface soil at the open burning site, bottom ash from a simple incinerator, bottom ash generated from the municipal solid waste (MSW) incinerator used for medical waste disposal, and bottom ash and fly ash from an incinerator exclusively used for medical waste. The species of PAHs were analyzed, and the toxicity equivalency quantities (TEQs) of samples calculated. Analysis results indicate that the content of total PAHs in fly ash was 1.8 × 10{sup 3} times higher than that in bottom ash, and that the strongly carcinogenic PAHs with four or more rings accumulated sensitively in fly ash. The test results of samples gathered from open burning site demonstrate that Acenaphthylene (ACY), Acenaphthene (ACE), Fluorene (FLU), Phenanthrene (PHE), Anthracene (ANT) and other PAHs were inclined to migrate into surrounding environment along air and surface watershed corridors, while 4- to 6-ring PAHs accumulated more likely in soil. Being consistent with other studies, it has also been confirmed that increases in both free oxygen molecules and combustion temperatures could promote the decomposition of polycyclic PAHs. In addition, without the influence of combustion conditions, there is a positive correlation between total PCDD/Fs and total PAHs, although no such relationship has been found for TEQ.« less

An Early-Warning System for Volcanic Ash Dispersal: The MAFALDA Procedure

NASA Astrophysics Data System (ADS)

Barsotti, S.; Nannipieri, L.; Neri, A.

2006-12-01

Forecasts of the dispersal of volcanic ash is a fundamental goal in order to mitigate its potential impact on urbanized areas and transport routes surrounding explosive volcanoes. To this aim we developed an early- warning procedure named MAFALDA (Modeling And Forecasting Ash Loading and Dispersal in the Atmosphere). Such tool is able to quantitatively forecast the atmospheric concentration of ash as well as the ground deposition as a function of time over a 3D spatial domain.\\The main features of MAFALDA are: (1) the use of the hybrid Lagrangian-Eulerian code VOL-CALPUFF able to describe both the rising column phase and the atmospheric dispersal as a function of weather conditions, (2) the use of high-resolution weather forecasting data, (3) the short execution time that allows to analyse a set of scenarios and (4) the web-based CGI software application (written in Perl programming language) that shows the results in a standard graphical web interface and makes it suitable as an early-warning system during volcanic crises.\\MAFALDA is composed by a computational part that simulates the ash cloud dynamics and a graphical interface for visualizing the modelling results. The computational part includes the codes for elaborating the meteorological data, the dispersal code and the post-processing programs. These produces hourly 2D maps of aerial ash concentration at several vertical levels, extension of "threat" area on air and 2D maps of ash deposit on the ground, in addition to graphs of hourly variations of column height.\\The processed results are available on the web by the graphical interface and the users can choose, by drop-down menu, which data to visualize. \\A first partial application of the procedure has been carried out for Mt. Etna (Italy). In this case, the procedure simulates four volcanological scenarios characterized by different plume intensities and uses 48-hrs weather forecasting data with a resolution of 7 km provided by the Italian Air Force.

Heavy metal content in ash of energy crops growing in sewage-contaminated natural wetlands: potential applications in agriculture and forestry?

PubMed

Bonanno, Giuseppe; Cirelli, Giuseppe Luigi; Toscano, Attilio; Lo Giudice, Rosa; Pavone, Pietro

2013-05-01

One of the greatest current challenges is to find cost-effective and eco-friendly solutions to the ever increasing needs of modern society. Some plant species are suitable for a multitude of biotechnological applications such as bioenergy production and phytoremediation. A sustainable practice is to use energy crops to clean up polluted lands or to treat wastewater in constructed wetlands without claiming further arable land for biofuel production. However, the disposal of combustion by-products may add significant costs to the whole process, especially when it deals with toxic waste. This study aimed to investigate the possibility of recycling ash from energy biomass as a fertilizer for agriculture and forestry. In particular, the concentrations of Cd, Cr, Cu, Mn, Pb and Zn were analyzed in the plant tissues and corresponding ash of the grasses Phragmites australis and Arundo donax, collected in an urban stream affected by domestic sewage. Results showed that the metal concentration in ash is 1.5-3 times as high as the values in plant tissues. However, metal enriched ash showed much lower element concentrations than the legal limits for ash reutilization in agriculture and forestry. This study found that biomass ash from constructed wetlands may be considered as a potential fertilizer rather than hazardous waste. Energy from biomass can be a really sustainable and clean option not only through the reduction of greenhouse gas emissions, but also through ash recycling for beneficial purposes, thus minimizing the negative impacts of disposal. Copyright © 2013 Elsevier B.V. All rights reserved.

Climate change reverses the competitive balance of ash and beech seedlings under simulated forest conditions.

PubMed

Saxe, H; Kerstiens, G

2005-07-01

This study identifies the important role of climate change and photosynthetic photon flux density (PPFD) in the regenerative competence of ash and beech seedlings in 12 inter- and intra-specific competition designs in simulated mixed ash-beech forest gaps under conditions of non-limiting soil volume, water and nutrient supply. The growth conditions simulated natural forest conditions as closely as possible. Simulations were performed by growing interacting seedling canopies for one season in temperature-regulated closed-top chambers (CTCs). Eight CTCs were used in a factorial design with replicate treatments of [CO2] x temperature x PPFD x competition design. [CO2] tracked ambient levels or was 360 micromol mol-1 higher. Temperature tracked ambient levels or was 2.8 degrees C higher. PPFD on two plant tables inside each CTC was 16% and 5% of open-field levels, respectively, representative of typical light flux levels in a natural forest gap. In several of the competition designs, climate change made the ash seedlings grow taller than the beech seedlings and, at the same time, attain a larger leaf area and a larger total biomass. Advantages of this type for ash were found particularly at lower PPFD. There was a positive synergistic interaction of elevated temperature x [CO2] for both species, but more so for ash. There are many uncertainties when a study of chambered seedlings is to be projected to real changes in natural forests. Nevertheless, this study supports a possible future shift towards ash in north European, unmanaged, mixed ash-beech forests in response to the predicted climate change.

Impurity confinement and transport in high confinement regimes without edge localized modes on DIII-D [Impurity confinement and transport in high confinement regimes without ELMs on DIII-D

DOE PAGES

Grierson, Brian A.; Burrell, Keith H.; Nazikian, Raffi M.; ...

2015-04-17

Here, impurity transport in the DIII-D tokamak is investigated in stationary high confinement (H-mode) regimes without edge localized modes (ELMs). In plasmas maintained by resonant magnetic perturbation (RMP) ELM-suppression and QH-mode the confinement time of fluorine (Z=9) is equivalent to that in ELMing discharges with 40 Hz ELMs. For selected discharges with impurity injection the impurity particle confinement time compared to the energy confinement time is in the range of τ p/τ e ≈ 2 $-$ 3. In QH-mode operation the impurity confinement time is shown to be smaller for intense, coherent magnetic and density fluctuations of the edge harmonicmore » oscillation than weaker fluctuations. Transport coefficients are derived from the time evolution of the impurity density profile and compared to neoclassical and turbulent transport models NEO and TGLF. Neoclassical transport of fluorine is found to be small compared to the experimental values. In the ELMing and RMP ELM-suppressed plasma the impurity transport is affected by the presence of tearing modes. For radii larger than the mode radius the TGLF diffusion coefficient is smaller than the experimental value by a factor of 2-3, while the convective velocity is within error estimates. Low levels of diffusion are observed for radii smaller than the tearing mode radius. In the QH-mode plasma investigated, the TGLF diffusion coefficient higher inside of ρ = 0.4 and lower outside of 0.4 than the experiment, and the TGLF convective velocity is more negative by a factor of approximately 1.7.« less

Exploring connections between trees and human health

Treesearch

Geoffrey Donovan; Marie Oliver

2014-01-01

Humans have intuitively understood the value of trees to their physical and mental health since the beginning of recorded time. A scientist with the Pacific Northwest Research Station wondered if such a link could be scientifically validated. His research team took advantage of an infestation of emerald ash borer, an invasive pest that kills ash trees, to conduct a...

Temporal dynamics of woodpecker predation on emerald ash borer ( Agrilus planipennis ) in the northeastern U.S.A.

Treesearch

David E. Jennings; Jian J. Duan; Leah S. Bauer; Jonathan M. Schmude; Miles T. Wetherington; Paula M. Shrewsbury

2015-01-01

Woodpeckers (Picidae) are important natural enemies attacking emerald ash borer (EAB) Agrilus planipennis Fairmaire in North America. There can be considerable variation in predation levels within and between sites, and among different times of year; therefore, understanding what causes these differences is necessary for effectively predicting EAB...

The design of control system of livestock feeding processing

NASA Astrophysics Data System (ADS)

Sihombing, Juna; Napitupulu, Humala L.; Hidayati, Juliza

2018-03-01

PT. XYZ is a company that produces animal feed. One type of animal feed produced is 105 ISA P. In carrying out its production process, PT. XYZ faces the problem of rejected feed amounts during 2014 to June 2015 due to the amount of animal feed that exceeds the standard feed quality of 13% of moisture content and 3% for ash content. Therefore, the researchers analyzed the relationship between factors affecting the quality and extent of damage by using regression and correlation and determine the optimum value of each processing process. Analysis results found that variables affecting product quality are mixing time, steam conditioning temperature and cooling time. The most dominant variable affecting the product moisture content is mixing time with the correlation coefficient of (0.7959) and the most dominant variable affecting the ash content of the product during the processing is mixing time with the correlation coefficient of (0.8541). The design of the proposed product processing control is to run the product processing process with mixing time 235 seconds, steam conditioning temperature 87 0C and cooling time 192 seconds. Product quality 105 ISA P obtained by using this design is with 12.16% moisture content and ash content of 2.59%.

Approaches for the accurate definition of geological time boundaries

NASA Astrophysics Data System (ADS)

Schaltegger, Urs; Baresel, Björn; Ovtcharova, Maria; Goudemand, Nicolas; Bucher, Hugo

2015-04-01

Which strategies lead to the most precise and accurate date of a given geological boundary? Geological units are usually defined by the occurrence of characteristic taxa and hence boundaries between these geological units correspond to dramatic faunal and/or floral turnovers and they are primarily defined using first or last occurrences of index species, or ideally by the separation interval between two consecutive, characteristic associations of fossil taxa. These boundaries need to be defined in a way that enables their worldwide recognition and correlation across different stratigraphic successions, using tools as different as bio-, magneto-, and chemo-stratigraphy, and astrochronology. Sedimentary sequences can be dated in numerical terms by applying high-precision chemical-abrasion, isotope-dilution, thermal-ionization mass spectrometry (CA-ID-TIMS) U-Pb age determination to zircon (ZrSiO4) in intercalated volcanic ashes. But, though volcanic activity is common in geological history, ashes are not necessarily close to the boundary we would like to date precisely and accurately. In addition, U-Pb zircon data sets may be very complex and difficult to interpret in terms of the age of ash deposition. To overcome these difficulties we use a multi-proxy approach we applied to the precise and accurate dating of the Permo-Triassic and Early-Middle Triassic boundaries in South China. a) Dense sampling of ashes across the critical time interval and a sufficiently large number of analysed zircons per ash sample can guarantee the recognition of all system complexities. Geochronological datasets from U-Pb dating of volcanic zircon may indeed combine effects of i) post-crystallization Pb loss from percolation of hydrothermal fluids (even using chemical abrasion), with ii) age dispersion from prolonged residence of earlier crystallized zircon in the magmatic system. As a result, U-Pb dates of individual zircons are both apparently younger and older than the depositional age of the ash, therefore masking the true age of deposition. Trace element ratios such as Th/U, Yb/Gd, as well as Hf isotope analysis of dated zircon can be used to decipher the temporal evolution of the magmatic system before the eruption and deposition of the studied ashes, and resolve the complex system behaviour of the zircons. b) Changes in the source of the magma may happen between the deposition of two stratigraphically consecutive ash beds. They result in the modification of the trace element signature of zircon, but also of apatite (Ca5 (F, Cl, OH) (PO4)3). Trace element characteristics in apatite (e.g. Mg, Mn, Fe, F, Cl, Ce, and Y) are a reliable tool for distinguishing chemically similar groups of apatite crystals to unravel the geochemical fingerprint of one single ash bed. By establishing this fingerprint, ash beds of geographically separated geologic sections can be correlated even if they have not all been dated by U-Pb techniques. c) The ultimate goal of quantitative stratigraphy is to establish an age model that predicts the age of a synchronous time line with an associated 95% confidence interval for any such line within a stratigraphic sequence. We show how a Bayesian, non-parametric interpolation approach can be applied to very complex data sets and leads to a well-defined age solution, possibly identifying changes in sedimentation rate. The age of a geological time boundary bracketed by dated samples in such an age model can be defined with an associated uncertainty.

Effects of Changing pH, Incubation Time, and As(V) Competition, on F- Retention on Soils, Natural Adsorbents, By-Products, and Waste Materials.

PubMed

Quintáns-Fondo, Ana; Santás-Miguel, Vanesa; Nóvoa-Muñoz, Juan C; Arias-Estévez, Manuel; Fernández-Sanjurjo, María J; Álvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

2018-01-01

The purpose of this work was to elucidate the repercussion of changing pH, incubation time and As(V) competition on fluoride (F - ) sorption on forest and vineyard soil samples, pyritic, and granitic materials, as well as on the by-products pine sawdust, oak wood ash, mussel shell ash, fine and coarse mussel shell, and slate processing waste fines. To reach this end, the methodological approach was based on batch-type experiments. The results indicate that, for most materials, F - sorption was very high at the start, but was clearly diminished when the pH value increased. However, oak wood ash and shell ash showed high F - sorption even at alkaline pH, and pine sawdust showed low F - sorption for any pH value. Specifically, F - sorption was close to 100% for both ashes at pH < 6, and around 70% at pH 10, while for forest soil it was close to 90% at pH < 2, and around 60% at pH values near 8. Regarding the effect of incubation time on F - sorption, it was very low for both soils, pyritic material, granitic material, and both kinds of ashes, as all of them showed very rapid F - sorption from the start, with differences being lesser than 10% between sorption at 30 min and 1 month of incubation. However, sawdust and slate fines sorbed 20% of added F - in 30 min, remaining constant up to 12 h, and doubling after 30 days. And finally, mussel shell sorbed 20% at 30 min, increasing to close to 60% when incubation time was 30 days. This means that some of the materials showed a first sorption phase characterized by rapid F - sorption, and a slower sorption in a second phase. As regards the effect of the presence of As(V) on F - sorption, it was almost negligible, indicating the absence of competition for sorption sites. In view of that all, these results could aid to appropriately manage soils and by-products when focusing on F - removal, in circumstances where pH value changes, contact time vary from hours to days, and potential competition between F - and As(V) could take place.

Effects of changing pH, incubation time, and As(V) competition, on F- retention on soils, natural adsorbents, by-products, and waste materials

NASA Astrophysics Data System (ADS)

Quintáns-Fondo, Ana; Santás-Miguel, Vanesa; Nóvoa-Muñoz, Juan C.; Arias-Estévez, Manuel; Fernández-Sanjurjo, María J.; Álvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

2018-03-01

The purpose of this work was to elucidate the repercussion of changing pH, incubation time and As(V) competition on fluoride (F-) sorption on forest and vineyard soil samples, pyritic and granitic materials, as well as on the by-products pine sawdust, oak wood ash, mussel shell ash, fine and coarse mussel shell, and slate processing waste fines. To reach this end, the methodological approach was based on batch-type experiments. The results indicate that, for most materials, F- sorption was very high at the start, but was clearly diminished when the pH value increased. However, oak wood ash and shell ash showed high F- sorption even at alkaline pH, and pine sawdust showed low F- sorption for any pH value. Specifically, F- sorption was close to 100% for both ashes at pH <6, and around 70% at pH 10, while for forest soil it was close to 90% at pH <2, and around 60% at pH values near 8. Regarding the effect of incubation time on F- sorption, it was very low for both soils, pyritic material, granitic material and both kinds of ashes, as all of them showed very rapid F- sorption from the start, with differences being lesser than 10% between sorption at 30 min and 1 month of incubation. However, sawdust and slate fines sorbed 20% of added F- in 30 minutes, remaining constant up to twelve hours, and doubling after 30 days. And finally, mussel shell sorbed 20% at 30 minutes, increasing to close to 60% when incubation time was 30 days. This means that some of the materials showed a first sorption phase characterized by rapid F- sorption, and a slower sorption in a second phase. As regards the effect of the presence of As(V) on F- sorption, it was almost negligible, indicating the absence of competition for sorption sites. In view of that all, these results could aid to appropriately manage soils and by-products when focusing on F- removal, in circumstances where pH value changes, contact time vary from hours to days, and potential competition between F- and As(V) could take place.

Atlantic salmon endothelial cells from the heart were more susceptible than fibroblasts from the bulbus arteriosus to four RNA viruses but protected from two viruses by dsRNA pretreatment.

PubMed

Pham, Phuc H; Tong, Winnie W L; Misk, Ehab; Jones, Ginny; Lumsden, John S; Bols, Niels C

2017-11-01

Heart diseases caused by viruses are major causes of Atlantic salmon aquaculture loss. Two Atlantic salmon cardiovascular cell lines, an endothelial cell line (ASHe) from the heart and a fibroblast cell line (BAASf) from the bulbus arteriosus, were evaluated for their response to four fish viruses, CSV, IPNV, VHSV IVa and VHSV IVb, and the innate immune agonist, double-stranded RNA mimic poly IC. All four viruses caused cytopathic effects in ASHe and BAASf. However, ASHe was more susceptible to all four viruses than BAASf. When comparing between the viruses, ASHe cells were found to be moderately susceptible to CSV and VHSV IVb, but highly susceptible to IPNV and VHSV IVa induced cell death. All four viruses were capable of propagating in the ASHe cell line, leading to increases in virus titre over time. In BAASf, CSV and IPNV produced more than one log increase in titre from initial infection, but VHSV IVb and IVa did not. When looking at the antiviral response of both cell lines, Mx proteins were induced in ASHe and BAASf by poly IC. All four viruses induced Mx proteins in BAASf, while only CSV and VHSV IVb induced Mx proteins in ASHe. IPNV and VHSV IVa suppressed Mx proteins expression in ASHe. Pretreatment of ASHe with poly IC to allow for Mx proteins accumulation protected the culture from subsequent infections with IPNV and VHSV IVa, resulting in delayed cell death, reduced virus titres and reduced viral proteins expression. These data suggest that endothelial cells potentially can serve as points of infections for viruses in the heart and that two of the four viruses, IPNV and VHSV IVa, have mechanisms to avoid or downregulate antiviral responses in ASHe cells. Furthermore, the high susceptibility of the ASHe cell line to IPNV and VHSV IVa can make it a useful tool for studying antiviral compounds against these viruses and for general detection of fish viruses. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of a sintering process for recycling oil shale fly ash and municipal solid waste incineration bottom ash into glass ceramic composite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Zhikun; Zhang, Lei; Li, Aimin, E-mail: leeam@dlut.edu.cn

Highlights: • Glass ceramic composite is prepared from oil shale fly ash and MSWI bottom ash. • A novel method for the production of glass ceramic composite is presented. • It provides simple route and lower energy consumption in terms of recycling waste. • The vitrified slag can promote the sintering densification process of glass ceramic. • The performances of products decrease with the increase of oil shale fly ash content. - Abstract: Oil shale fly ash and municipal solid waste incineration bottom ash are industrial and municipal by-products that require further treatment before disposal to avoid polluting the environment.more » In the study, they were mixed and vitrified into the slag by the melt-quench process. The obtained vitrified slag was then mixed with various percentages of oil shale fly ash and converted into glass ceramic composites by the subsequent sintering process. Differential thermal analysis was used to study the thermal characteristics and determine the sintering temperatures. X-ray diffraction analysis was used to analyze the crystalline phase compositions. Sintering shrinkage, weight loss on ignition, density and compressive strength were tested to determine the optimum preparation condition and study the co-sintering mechanism of vitrified amorphous slag and oil shale fly ash. The results showed the product performances increased with the increase of sintering temperatures and the proportion of vitrified slag to oil shale fly ash. Glass ceramic composite (vitrified slag content of 80%, oil shale fly ash content of 20%, sintering temperature of 1000 °C and sintering time of 2 h) showed the properties of density of 1.92 ± 0.05 g/cm{sup 3}, weight loss on ignition of 6.14 ± 0.18%, sintering shrinkage of 22.06 ± 0.6% and compressive strength of 67 ± 14 MPa. The results indicated that it was a comparable waste-based material compared to previous researches. In particular, the energy consumption in the production process was reduced compared to conventional vitrification and sintering method. Chemical resistance and heavy metals leaching results of glass ceramic composites further confirmed the possibility of its engineering applications.« less

Toward an integrated Volcanic Ash Observing System in Europe

NASA Astrophysics Data System (ADS)

Lee, Deborah; Lisk, Ian

2014-05-01

Volcanic ash from the Icelandic eruption of Eyjafjallajökull in April and May of 2010 resulted in the decision by many northern European countries to impose significant restrictions on the use of their airspace. The eruption, extent and persistence of the ash revealed how reliant society now is on a safe and efficient air transport system and the fragility of that system when affected by the impact of complex natural hazards. As part of an EC framework programme, the 2011-2013 WEZARD (WEather HaZARD for aeronautics) consortium conducted a cross-industry volcanic ash capability and gap analyses, with the EUMETNET (network of 29 National Meteorological Services) led Work Package 3 focussing on a review of observational and monitoring capabilities, atmospheric dispersion modelling and data exchange. The review has revealed a patchwork of independent observing capabilities for volcanic ash, with some countries investing and others not at all, and most existing networks focus on space-based products. Existing capabilities do not provide the necessary detail on the geographical and vertical extent of volcanic ash and associated levels of contamination, which decision makers in the aviation industry require in order to decide where it is safe to fly. A resultant high priority was identified by WEZARD Work Package 3 for an enhanced observational network of complementary monitoring systems needed to initialise, validate and verify volcanic ash dispersion model output and forecasts. Thus a key recommendation is to invest in a major pre-operational demonstrator "European volcanic ash observing network", focussing on distal monitoring, and aiming to a) fill R&D gaps identified in instrumentation and algorithms and b) integrate data, where possible in near-real-time, from a range of ground-based, airborne and space-based techniques. Here we present a key WEZARD recommendation toward an integrated volcanic ash observing system in Europe, in context with other related projects and initiatives. We will also look to highlight the work underway by VAACs (Volcanic Ash Advisory Centres) and aviation regulatory authorities within the IAVWOPSG (International Airways Volcano Watch Operations Group) to develop the 'agreed in situ and/or remote sensing techniques' that underpin the newly approved definition of 'Discernible ash'.

Aerosol properties and meteorological conditions in the city of Buenos Aires, Argentina, during the resuspension of volcanic ash from the Puyehue-Cordón Caulle eruption

NASA Astrophysics Data System (ADS)

Graciela Ulke, Ana; Torres Brizuela, Marcela M.; Raga, Graciela B.; Baumgardner, Darrel

2016-09-01

The eruption in June 2011 of the Puyehue-Cordón Caulle Volcanic Complex in Chile impacted air traffic around the Southern Hemisphere for several months after the initial ash emissions. The ash deposited in vast areas of the Patagonian Steppe was subjected to the strong wind conditions prevalent during the austral winter and spring experiencing resuspension over various regions of Argentina. In this study we analyze the meteorological conditions that led to the episode of volcanic ash resuspension which impacted the city of Buenos Aires and resulted in the closure of the two main airports in Buenos Aires area (Ezeiza and Aeroparque) on 16 October 2011. A relevant result is that resuspended material (volcanic ash plus dust) imprints a distinguishable feature within the atmospheric thermodynamic vertical profiles. The thermodynamic soundings show the signature of "pulses of drying" in layers associated with the presence of hygroscopic ash in the atmosphere that has already been reported in similar episodes after volcanic eruptions in other parts of the world. This particular footprint can be used to detect the probable existence of volcanic ash layers. This study also illustrates the utility of ceilometers to detect not only cloud base at airports but also volcanic ash plumes at the boundary layer and up to 7 km altitude. Aerosol properties measured in the city during the resuspension episode indicate the presence of enhanced concentrations of aerosol particles in the boundary layer along with spectral signatures in the measurements at the Buenos Aires AERONET site typical of ash plus dust advected towards the city. The mandatory aviation reports from the National Weather Service about airborne and deposited volcanic ash at the airport near the measurement site (Aeroparque) correlate in time with the enhanced concentrations. The presence of the resuspended material was detected by the CALIOP lidar overpassing the region. Since the dynamics of ash resuspension and recirculation are similar to the dynamics of dust storms, we use the HYSPLIT model with the dust storm module to simulate the episode that affected Buenos Aires. The results of the modeling agree qualitatively with satellite lidar measurements.

Biology, life history, and laboratory rearing of Spathius galinae (Hymenoptera: Braconidae), a larval parasitoid of the invasive emerald ash borer (Coleoptera: Buprestidae).

PubMed

Duan, Jian J; Watt, Timothy J; Larson, Kristi

2014-06-01

Spathius galinae Belokobylskij & Strazanac is a recently described parasitoid of the emerald ash borer, Agrilus planipennis Fairmaire, in the Russian Far East, and is currently being considered for biocontrol introduction in the United States. Using A. planipennis larvae reared with freshly cut ash (Fraxinus spp.) sticks, we investigated the biology, life cycle, and rearing of S. galinae in the laboratory under normal rearing conditions (25 +/- 1 degrees C, 65 +/- 10% relative humidity, and a photoperiod of 16:8 [L:D] h). Our study showed that S. galinae took approximately 1 mo (29 d) to complete a single generation (from egg to adult) under the laboratory rearing conditions. After eclosion from eggs, larvae of S. galinae molted four times to reach the fifth instar, which then spun cocoons for pupation and development to adults. Adult female wasps had a median survival time of 7 wk with fecundity peaking 3 wk after emergence when reared in groups (of five females and five males) and 2 wk in single pairs. Throughout the life span, a single female S. galinae produced a mean (+/- SE) of 31 (+/- 3.0) progeny when reared in groups, and a mean (+/- SE) of 47 (+/- 5.3) progeny when reared in single pairs. Results from our study also showed that S. galinae could be effectively reared with A. planipennis larvae reared in both green (Fraxinus pennsylvanica Marshall) and tropical [Fraxinus uhdei (Wenzig) Lingelsh] ash sticks. However, the abortion (unemergence) rate of S. galinae progeny was much higher (20%) when reared with host larvae in green ash sticks than that (2.1%) in tropical ash sticks.

Laboratory Evaluation of the Toxicity of Systemic Insecticides to Emerald Ash Borer Larvae.

PubMed

Poland, Therese M; Ciaramitaro, Tina M; McCullough, Deborah G

2016-04-01

Emerald ash borer (Agrilus planipennis Fairmaire) (Coleoptera: Buprestidae), an invasive phloem-feeding insect native to Asia, threatens at least 16 North American ash (Fraxinus) species and has killed hundreds of millions of ash trees in landscapes and forests. We conducted laboratory bioassays to assess the relative efficacy of systemic insecticides to control emerald ash borer larvae in winter 2009 and 2010. Second- and third-instar larvae were reared on artificial diet treated with varying doses of emamectin benzoate (TREE-äge, Arborjet, Inc., Woburn, MA), imidacloprid (Imicide, J. J Mauget Co., Arcadia, CA), dinotefuran (Safari, Valent Professional Products, Walnut Creek, CA), and azadirachtin (TreeAzin, BioForest Technologies, Inc., Sault Ste. Marie, Ontario, and Azasol, Arborjet, Inc., Woburn, MA). All of the insecticides were toxic to emerald ash borer larvae, but lethal concentrations needed to kill 50% of the larvae (LC50), standardized by larval weight, varied with insecticide and time. On the earliest date with a significant fit of the probit model, LC50 values were 0.024 ppm/g at day 29 for TREE-äge, 0.015 ppm/g at day 63 for Imicide, 0.030 ppm/g at day 46 for Safari, 0.025 ppm/g at day 24 for TreeAzin, and 0.027 ppm/g at day 27 for Azasol. The median lethal time to kill 50% (LT50) of the tested larvae also varied with insecticide product and dose, and was longer for Imicide and Safari than for TREE-äge or the azadirachtin products. Insecticide efficacy in the field will depend on adult and larval mortality as well as leaf and phloem insecticide residues.

Time-lagged ensemble simulations of the dispersion of the Eyjafjallajökull plume over Europe with COSMO-ART

NASA Astrophysics Data System (ADS)

Vogel, H.; Förstner, J.; Vogel, B.; Hanisch, T.; Mühr, B.; Schättler, U.; Schad, T.

2014-08-01

An extended version of the German operational weather forecast model was used to simulate the ash dispersion during the eruption of the Eyjafjallajökull. As an operational forecast was launched every 6 hours, a time-lagged ensemble was obtained. Sensitivity runs show the ability of the model to simulate thin ash layers when an increased vertical resolution is used. Calibration of the model results with measured data allows for a quantitative forecast of the ash concentration. After this calibration an independent comparison of the simulated number concentration of 3 μm particles and observations at Hohenpeißenberg gives a correlation coefficient of 0.79. However, this agreement could only be reached after additional modifications of the emissions. Based on the time lagged ensemble the conditional probability of violation of a certain threshold is calculated. Improving the ensemble technique used in our study such probabilities could become valuable information for the forecasters advising the organizations responsible for the closing of the airspace.

The ash in forest fire affected soils control the soil losses. Part 2. Current and future research challenges

NASA Astrophysics Data System (ADS)

Pereira, Paulo; Cerdà, Artemi

2013-04-01

Ash distribution on soil surface and impacts on soil properties received a great attention in recently (Pereira et al., 2010; Pereira et al., 2013). Ash it is a highly mobile material that can be easily transported wind, especially in severe wildland fires, where organic matter is reduced to dust, due the high temperatures of combustion. In the immediate period after the fire, ash cover rules soil erosion as previous researchers observed (Cerdà, 1998a; 1998b) and have strong influence on soil hydrological properties, such as water retention (Stoof et al. 2011 ) and wettability (Bodi et al., 2011). Ash it is also a valuable source of nutrients important for plant recuperation (Pereira et al., 2011; Pereira et al., 2012), but can act also as a source contamination, since are also rich in heavy metals (Pereira and Ubeda, 2010). Ash has different physical and chemical properties according the temperature of combustion, burned specie and time of exposition (Pereira et al., 2010). Thus this different properties will have different implications on soil properties including erosion that can increase due soil sealing (Onda et al. 2008) or decrease as consequence of raindrop impact reduction (Cerdà and Doerr, 2008). The current knowledge shows that ash has different impacts on soil properties and this depends not only from the type of ash produced, but of the soil properties (Woods and Balfour, 2010). After fire wind and water strong redistribute ash on soil surface, increasing the vulnerability of soil erosion in some areas, and reducing in others. Understand this mobility is fundamental have a better comprehension about the spatial and temporal effects of ash in soil erosion. Have a better knowledge about this mobility is a priority to future research. Other important aspects to have to be assessed in the future are how ash particulates percolate on soil and how ash chemical composition is important to induce soil aggregation and dispersion. How soil micro topography have implications on ash spatial distribution and if soil micro topography changes with time? What the factors that controls it? What it is the impact of ash in vegetation recuperation and the implications of this recover in ash spatial distribution? We need studies with better spatial and temporal resolution, especially in the immediate period after the fire, when the major spatial and temporal changes on ash distribution and impacts occur. Based on high level research conducted by Artemi Cerdà and others, our future research will be focused in these and other aspects in order to have a better knowledge about the impacts of ash on post-fire spatio-temporal erosion. Acknowledgements, Lithuanian Research Council. Project LITFIRE, Fire effects on Lithuanian soils and ecosystems (MIP-48/2011) and the research projects GL2008-02879/BTE and LEDDRA 243857. References Bodí, M., Mataix-Solera, J., Doerr, S., and Cerdà, A. 2011b. The wettability of ash from burned vegetation and its relationship to Mediterranean plant species type, burn severity and total organic carbon content. Geoderma, 160, 599-607. Cerdà, A. 1998a. Postfire dynamics of erosional processes under mediterranean climatic conditions. Z. Geomorphol., 42 (3) 373-398. Cerdà, A. 1998b. Changes in overland flow and infiltration after a rangeland fire in a Mediterranean scrubland.Hydrological Processes, 12, 1031-1042. Cerdà, A., and Doerr, S.H. 2008. The effect of ash and needle cover on surface runoff and erosion in the immediate post-fire period. Catena, 74, 256-263. Onda, Y., Dietrich W. E., and Booker, F. 2008. Evolution of overland flow after severe forest fire, Point Reyes, California, Catena, 72, 13-20. Pereira, P. Cerdà, A., Úbeda, X., Mataix-Solera, J. Arcenegui, V., Zavala, L. 2013. Modelling the impacts of wildfire on ash thickness in a short-term period, Land Degradation and Development, (In press) Pereira, P., Bodi. M., Úbeda, X., Cerdà, A., Mataix-Solera, J., Balfour, V, Woods, S. 2010. Las cenizas y el ecosistema suelo, In: Cerdà, A. Jordan, A. (eds) Actualización en métodos y técnicas para el estudio de los suelos afectados por incendios forestales, 345-398. Càtedra de Divulgació de la Ciència. Universitat de Valencia. ISBN: 978-84-370-7887-8. Deposito Legal: V-3541-2010. Pereira, P., Úbeda, X. 2010. Spatial variation of heavy metals released from ashes after a wildfire, Journal of Environmental Engineering and Landscape Management, 18(1), 13-22. Pereira, P., Ubeda, X., Martin, D. 2012. Fire severity effects on ash chemical composition and water-extractable elements, Geoderma, 191, 105-114. Pereira, P., Úbeda, X., Martin, D., Mataix-Solera, J., Guerrero, C. 2011. Effects of a low prescribed fire in ash water soluble elements in a Cork Oak (Quercus suber) forest located in Northeast of Iberian Peninsula, Environmental Research, 111(2), 237-247. Stoff, C.R., Wesseling, J.G., Ritsema, C.J. 2011. Effects of ash on soil water retention, Geoderma, 159(3-4), 276-285. Woods, S.W., Balfour, V.N. 2010. The effects of soil texture and ash thickness on the post-fire hydrological response from ash-covered soils, Journal of Hydrology, 393, 274-286.

Ash after forest fires. Effects on soil hydrology and erosion

NASA Astrophysics Data System (ADS)

Bodí, Merche B.

2013-04-01

Hillslopes were though to be most susceptible to enhanced hydro-geomorphological responses immediately following burning, with susceptibility declining during the first months or years depending on the soil and vegetation recovery. However, Cerdà (1998) found some indices in that immediately after the fire, the thin wettable ash layer that typically covers the ground could absorb rainfall and prevent or delay the onset of overland flow and associated erosion. Therefore the time lag while ash remains on the ground become of crucial importance to protect the soil after a wildfire. The effect of this ash layer was rarely been considered in detail because ash has often been reduced or redistributed by wind or water erosion before the onset of monitoring and thus the data collection typically begun some weeks or month after the fire. The first papers focussed only on ash and its hydrological effects were published by Cerdà and Doerr (2008) and by Woods and Balfour (2008). The results showed that the soil covered with ash indeed reduced and delayed surface runoff, reduced soil splash detachment and produced lower sediment yield compared to bare terrain. However, these findings arose more questions, as for instance: Why in other research there were indices that ash reduces infiltration? what is the mechanism by which why ash reduces overland flow? The research went further with Bodí PhD. First of all, it was crucial the agreement on the fact that the material "ash" is very variable depending on the original vegetation and the type and temperature of combustion. Therefore ash properties are different between wildfires even and within a fire. This is the main reason of its different effects and thus ash not always reduces runoff and sediment yield. In this way, depending on the nature of ash, it can increase overland flow if it is crusted (usually it contains a high content of calcium carbonate), it is water repellent (with high contents of organic carbon and specially from certain Eucaliptus and Pinus), or if clog soil pores (depending also on the soil type). If ash is wettable, it can store even 80% of its volume and then it will delay and reduce overland flow proportionally to the thickness of the ash layer. Once ash gets saturated, the flow tends to adjust to an infiltration rate similar to the soil itself, or sometimes higher due to the protection of ash that can reduce soil water repellency and soil sealing (Bodí et al. 2011, 2012). Still, many other aspects on ash remain unknown and ash present us more questions like, what it is its role on the carbon cycle? what is the extent of the ahs effects at basin scale? what is the fate of ash and how long it remains in the ecosystem? are there specific effects of ash depending on the ecosystem and so the type of ash? Acknowledgements This work was supported financially by a research fellowship (AP2007-04602) from the Spanish Ministry of Science and Innovation (M.B. Bodí) and the projects PT2009-0073 and CGL2010-21670-C02-01. References Bodí, M.B., Mataix-Solera, J., Doerr, S.H., Cerdà, A., 2011, The wettability of ash from burned vegetation and its relationship to Mediterranean plant species type, burn severity and total organic carbon content. Geoderma 160, 599-607. Bodí, M.B., Doerr, S.H., Cerdà, A., Mataix-Solera, J., 2012, Hydrological effects of a layer of vegetation ash on underlying wettable and water repellent soil. Geoderma 191, 14-23 Cerdà, A., 1998, Changes in overland flow and infiltration after a rangeland fire in a Mediterranean scrubland. Hydrological Processes 12, 1031-1042. Cerdà, A., Doerr, S.H., 2008, The effect of ash and needle cover on surface runoff and erosion in the immediate post-fire period. Catena 74, 256-263. Woods, S.W., Balfour, V., 2008, The effect of ash on runoff and erosion after a forest wildfire, Montana, U.S.A. International Journal of Wildland Fire 17, 535-548.

Multi-sensor satellite monitoring of ash and SO2 volcanic plume in support to aviation control

NASA Astrophysics Data System (ADS)

Brenot, Hugues; Theys, Nicolas; Clarisse, Lieven; van Geffen, Jos; van Gent, Jeroen; Van Roozendael, Michel; van der A, Ronald; Hurtmans, Daniel; Coheur, Pierre-Francois; Clerbaux, Cathy; Valks, Pieter; Hedelt, Pascal; Prata, Fred; Rasson, Olivier; Sievers, Klaus; Zehner, Claus

2014-05-01

The 'Support to Aviation Control Service' (SACS; http://sacs.aeronomie.be) is an ESA-funded project hosted by the Belgian Institute for Space Aeronomy since 2007. The service provides near real-time (NRT) global volcanic ash and SO2 observations, as well as notifications in case of volcanic eruptions (success rate >95% for ash and SO2). SACS is based on the combined use of UV-visible (OMI, GOME-2 MetOp-A, GOME-2 MetOp-B) and infrared (AIRS, IASI MetOp-A, IASI MetOp-B) satellite instruments. The SACS service is primarily designed to support the Volcanic Ash Advisory Centers (VAACs) in their mandate to gather information on volcanic clouds and give advice to airline and air traffic control organisations. SACS also serves other users that subscribe to the service, in particular local volcano observatories, research scientists and airliner pilots. When a volcanic eruption is detected, SACS issues a warning that takes the form of a notification sent by e-mail to users. The SACS notification points to a dedicated web page where all relevant information is available and can be visualised with user-friendly tools. Information about the volcanic plume height from GOME-2 (MetOp-A and MetOp-B) are also available. The strength of a multi-sensor approach relies in the use of satellite data with different overpasses times, minimising the time-lag for detection and enhancing the reliability of such alerts. This presentation will give an overview of the SACS service, and of the different techniques used to detect volcanic plumes (ash, SO2 and plume height). It will also highlight the strengths and limitations of the service and measurements, and some perspectives.

Temporal and spatial variations in fly ash quality

USGS Publications Warehouse

Hower, J.C.; Trimble, A.S.; Eble, C.F.

2001-01-01

Fly ash quality, both as the amount of petrographically distinguishable carbons and in chemistry, varies in both time and space. Temporal variations are a function of a number of variables. Variables can include variations in the coal blend organic petrography, mineralogy, and chemistry; variations in the pulverization of the coal, both as a function of the coal's Hardgrove grindability index and as a function of the maintenance and settings of the pulverizers; and variations in the operating conditions of the boiler, including changes in the pollution control system. Spatial variation, as an instantaneous measure of fly ash characteristics, should not involve changes in the first two sets of variables listed above. Spatial variations are a function of the gas flow within the boiler and ducts, certain flow conditions leading to a tendency for segregation of the less-dense carbons in one portion of the gas stream. Caution must be applied in sampling fly ash. Samples from a single bin, or series of bins, m ay not be representative of the whole fly ash, providing a biased view of the nature of the material. Further, it is generally not possible to be certain about variation until the analysis of the ash is complete. ?? 2001 Elsevier Science B.V. All rights reserved.

Thermochemical treatment of sewage sludge ash with sodium salt additives for phosphorus fertilizer production--Analysis of underlying chemical reactions.

PubMed

Stemann, Jan; Peplinski, Burkhard; Adam, Christian

2015-11-01

Stocks of high grade phosphate rock are becoming scarce, and there is growing concern about potentially harmful impurities in conventional phosphorus fertilizers. Sewage sludge ash is a promising secondary phosphorus source. However, to remove heavy metals and convert the phosphorus contained in sewage sludge ash into mineral phases available to plants, an after-treatment is required. Laboratory-scale calcination experiments of sewage sludge ash blended with sodium salts using dried sewage sludge as a reducing agent were carried out at 1000°C. Thus, the Ca3(PO4)2 or whitlockite component of raw sewage sludge ash, which is not readily plant available, was converted to CaNaPO4 (buchwaldite). Consequently, nearly complete phosphorus solubility in ammonium citrate (a well-established indicator for plant availability) was achieved. Moreover, it was shown that Na2CO3 may be replaced by moderately priced Na2SO4. However, molar ratios of Na/P>2 were required to achieve >80% phosphorus solubility. Such over-stoichiometric Na consumption is largely caused by side reactions with the SiO2 component of the sewage sludge ash - an explanation for which clear evidence is provided for the first time. Copyright © 2015 Elsevier Ltd. All rights reserved.

Phosphorus leaching from soils amended with thermally gasified piggery waste ash.

PubMed

Kuligowski, Ksawery; Poulsen, Tjalfe Gorm

2009-09-01

In regions with intensive livestock farming, thermal treatment for local energy extraction from the manure and export of the P rich ash as a fertilizer has gained interest. One of the main risks associated with P fertilizers is eutrophication of water bodies. In this study P and K mobility in ash from anaerobically digested, thermally gasified (GA) and incinerated (IA) piggery waste has been tested using water loads ranging from 0.1 to 200 ml g(-1). Leaching of P from soil columns amended with GA was investigated for one P application rate (205 kg P ha(-1) corresponding to 91 mg P kg(-1) soil dry matter) as a function of precipitation rate (9.5 and 2.5 mm h(-1)), soil type (Jyndevad agricultural soil and sand), amount of time elapsed between ash amendment and onset of precipitation (0 and 5 weeks) and compared to leaching from soils amended with a commercial fertilizer (Na(2)HPO(4)). Water soluble P in GA and IA constituted 0.04% and 0.8% of total ash P. Ash amended soil released much less P (0.35% of total P applied in sand) than Na(2)HPO(4) (97% and 12% of total P applied in Jyndevad and sand, respectively).

Fly-ash geo-polymer foamed concrete

NASA Astrophysics Data System (ADS)

Kargin, Aleksey; Baev, Vladimir; Mashkin, Nikolay

2017-01-01

In recent years, the interest of researchrs in using fly-ash as a raw material for the geo-polymer synthesis is increasing. Kuzbass region (in Russia) has a large amount of ash wastes generated, which defined the relevace of the study performed in this paper. Results of investigating load-bearing capacity of structural insulating material produced by geo-polymerization of fly-ash of Kemerovo hydro-electric power plant with the addition of complex activator are described in the paper. Hydrogen peroxide solution was used as the foaming agent. The activation time, the temperature of isothermal holding and hardening in normal conditions for all samples were constant. The compressive strength and the mean density of geo-polymer foamed concrete were determined. The influence of the material composition on its properties was revealed. It is found that of the geo-polymer foamed concrete with the optimum composition has hardness of 1,1-3,5 MPa at the density of 400 to 900 kg/m3. Thus, the production of the fly-ash geo-polymer concretes and mortars is feasible, justified and promising.

Alkaline modified oil shale fly ash: optimal synthesis conditions and preliminary tests on CO2 adsorption.

PubMed

Reinik, Janek; Heinmaa, Ivo; Kirso, Uuve; Kallaste, Toivo; Ritamäki, Johannes; Boström, Dan; Pongrácz, Eva; Huuhtanen, Mika; Larsson, William; Keiski, Riitta; Kordás, Krisztián; Mikkola, Jyri-Pekka

2011-11-30

Environmentally friendly product, calcium-silica-aluminum hydrate, was synthesized from oil shale fly ash, which is rendered so far partly as an industrial waste. Reaction conditions were: temperature 130 and 160°C, NaOH concentrations 1, 3, 5 and 8M and synthesis time 24h. Optimal conditions were found to be 5M at 130°C at given parameter range. Original and activated ash samples were characterized by XRD, XRF, SEM, EFTEM, (29)Si MAS-NMR, BET and TGA. Semi-quantitative XRD and MAS-NMR showed that mainly tobermorites and katoite are formed during alkaline hydrothermal treatment. Physical adsorption of CO(2) on the surface of the original and activated ash samples was measured with thermo-gravimetric analysis. TGA showed that the physical adsorption of CO(2) on the oil shale fly ash sample increases from 0.06 to 3-4 mass% after alkaline hydrothermal activation with NaOH. The activated product has a potential to be used in industrial processes for physical adsorption of CO(2) emissions. Copyright © 2011 Elsevier B.V. All rights reserved.

Production of a bioflocculant from Pseudomonas veronii L918 using the hydrolyzate of peanut hull and its application in the treatment of ash-flushing wastewater generated from coal fired power plant.

PubMed

Liu, Weijie; Hao, Yan; Jiang, Jihong; Zhu, Aihua; Zhu, Jingrong; Dong, Zhen

2016-10-01

In this study, bioflocculant produced by Pseudomonas veronii L918 was applied to treat ash-flushing wastewater. The strain L918 could convert the hydrolyzate of peanut hull into bioflocculant, which can effectively reduce the production cost of bioflocculant. The yield of 3.39g/L bioflocculant MBF-L918 was achieved when 300mL/L peanut hull hydrolyzate was used as carbon source. The bioflocculant MBF-L918 contains 77.14% polysaccharides and 4.84% proteins, and the molecular weight (MW) of MBF-L918 is 24.77kDa. Furthermore, MBF-L918 showed good flocculating efficiency of 92.51% to ash-flushing wastewater when 2.83mg/L MBF-L918 was added, and thus achieved the recycling of ash-flushing wastewater. This study reported for the first time that the bioflocculant was produced using peanut hull hydrolyzate and effectively applied in the treatment of coal ash-flushing wastewater. Copyright © 2016 Elsevier Ltd. All rights reserved.

Structure and Dynamics of Ionic Liquid [MMIM][Br] Confined in Hydrophobic and Hydrophilic Porous Matrices: A Molecular Dynamics Simulation Study.

PubMed

Sharma, Anirban; Ghorai, Pradip Kr

2016-11-17

The effects of confinement on the structural and dynamical properties of the ionic liquid (IL) 1,3-dimethylimidazolium bromide ([MMIM][Br]) have been investigated by molecular dynamics simulations. We used zeolite faujasite (NaY) as a hydrophilic confinement and dealuminated faujasite (DAY) as a hydrophobic confinement. The presence of an extra framework cation, [Na + ], in NaY makes the host hydrophilic, whereas DAY, with no extra framework cation, is hydrophobic. Although both NaY and DAY have almost similar structures, the IL showed markedly different structural and dynamical properties in these confinements and in bulk. In the confinements, the cation-cation radial distribution function, which strongly depends on temperature, exhibits a layer-like structure, whereas in bulk, it shows a liquid-like structure that hardly depends on temperature. Although the interaction between [MMIM] + and Br - in DAY is stronger than that in both NaY and bulk, the strength of the interaction between them is almost invariant with temperature. Both [MMIM] + and Br - strongly interact with Na + of the host, and their interaction strongly depends on temperature, whereas the interaction of the IL with Si and O is very weak and invariant with temperature. In bulk, the self-diffusion coefficient, [D], of both [MMIM] + and Br - increases exponentially with temperature, and the D of the cation is slightly higher than that of the anion at all studied temperatures, whereas in the confinements, [MMIM] + moves much faster than Br - . For example, in the hydrophilic confinement, the D of the cation is 20-30 times higher than that of the anion. The D of both the ions decreases significantly in the confinements as compared to that in bulk. During diffusion, [MMIM] + diffuses closer to the inner surface in the hydrophilic confinement than that in the hydrophobic confinement. The diffusion pathway imperceptibly depends on temperature but strongly depends on the nature of the confinement. The self part of the time-dependent van Hoove correlation function of [MMIM] + in the hydrophilic confinement shows a larger deviation from its Gaussian form than that in the hydrophobic confinement at all temperatures, indicating that the long-time dynamics of [MMIM] + in NaY is more heterogeneous than that in DAY. Although the orientational relaxation time scales of [MMIM] + in the confinements significantly slowed as compared to those in bulk, confinement does not affect the librational motion of the collective hydrogen-bond network present in the IL.

Effect of temperature on the hydration of Portland cement blended with siliceous fly ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deschner, Florian, E-mail: florian.deschner@gmail.com; Lothenbach, Barbara; Winnefeld, Frank

2013-10-15

The effect of temperature on the hydration of Portland cement pastes blended with 50 wt.% of siliceous fly ash is investigated within a temperature range of 7 to 80 °C. The elevation of temperature accelerates both the hydration of OPC and fly ash. Due to the enhanced pozzolanic reaction of the fly ash, the change of the composition of the C–S–H and the pore solution towards lower Ca and higher Al and Si concentrations is shifted towards earlier hydration times. Above 50 °C, the reaction of fly ash also contributes to the formation of siliceous hydrogarnet. At 80 °C, ettringitemore » and AFm are destabilised and the released sulphate is partially incorporated into the C–S–H. The observed changes of the phase assemblage in dependence of the temperature are confirmed by thermodynamic modelling. The increasingly heterogeneous microstructure at elevated temperatures shows an increased density of the C–S–H and a higher coarse porosity. -- Highlights: •The reaction of quartz powder at 80 °C strongly enhances the compressive strength. •Almost no strength increase of fly ash blended OPC at 80 °C was found after 2 days. •Siliceous hydrogarnet is formed upon the reaction of fly ash at high temperatures. •Temperature dependent change of the system was simulated by thermodynamic modelling. •Destabilisation of ettringite above 50 °C correlates with sulphate content of C–S–H.« less

Using acid insoluble ash marker ratios (diet:digesta) to predict digestibility of wheat and barley metabolizable energy and nitrogen retention in broiler chicks.

PubMed

Scott, T A; Hall, J W

1998-05-01

Routine bioassay measurements of AME or N retention of broiler diets require measurements of gross energy (GE) or N and an acid insoluble ash marker in diet, excreta, or ileal digesta. These measurements of GE and N are time-consuming and expensive in comparison to measurements of added or natural occurring levels of acid insoluble ash. Data from bioassay measurements of AME and N retention of 138 wheat and 97 barley samples (with or without enzyme) were used to develop prediction equations relying on measurements of one that uses acid insoluble ash of diet, excreta or ileal digesta and GE and N of diet only; and a second equation using only acid insoluble ash of diet, excreta, or ileal digesta. The prediction equations demonstrate that part of or all of routine bomb calorimetry measurements for GE used to determine AME of wheat- or barley-based diets could be eliminated if a prediction error of 80 kcal/kg ME or less were acceptable. The prediction of N retention as compared to AME, based in part or totally on acid insoluble ash measurements, was less accurate; the prediction errors were equal to 2.3 and 6.5% for wheat- and barley-based diets, respectively. Ongoing research to improve the determination (speed, ease, and accuracy) of acid insoluble ash could provide a useful method to assess feeding value of ingredients and commercial poultry diets.

Evaluation of leachate emissions from crushed rock and municipal solid waste incineration bottom ash used in road construction.

PubMed

Lidelöw, S; Lagerkvist, A

2007-01-01

Three years of leachate emissions from municipal solid waste incineration bottom ash and crushed rock in a full-scale test road were evaluated. The impact of time, construction design, and climate on the emissions was studied, and the predicted release from standard leaching tests was compared with the measured release from the road. The main pollutants and their respective concentrations in leachate from the roadside slope were Al (12.8-85.3 mg l(-1)), Cr (2-125 microg l(-1)), and Cu (0.15-1.9 mg l(-1)) in ash leachate and Zn (1-780 microg l(-1)) in crushed rock leachate. From the ash, the initial Cl(-) release was high ( approximately 20 g l(-1)). After three years, the amount of Cu and Cl(-) was in the same range in both leachates, while that of Al and Cr still was more than one order of magnitude higher in ash leachate. Generally, the release was faster from material in the uncovered slopes than below the pavement. Whether the road was asphalted or not, however, had minor impacts on the leachate quality. During rain events, diluted leachates with respect to, e.g., salts were observed. The leaching tests failed to simulate field leaching from the crushed rock, whereas better agreement was observed for the ash. Comparisons of constituent release from bottom ash and conventional materials solely based on such tests should be avoided.

Application of washed MSWI fly ash in cement composites: long-term environmental impacts.

PubMed

Yang, Zhenzhou; Tian, Sicong; Liu, Lili; Wang, Xidong; Zhang, Zuotai

2018-04-01

In the present study, long-term environmental impacts of compact and ground cement composites, in which 30 wt.% of cement was replaced by washed municipal solid wastes incineration (MSWI) fly ash, were investigated for use in building industry. Consecutive leaching tests over a time span of 180 days were performed in acid water, deionized water, and saline water, respectively, with the accumulative concentration of different elements determined in the leachate. Different leaching behaviors are observed among different potential toxic elements (PTEs). For instance, higher concentrations of V in the leachate were observed from the compact cement composites than those from the ground ones. The concentration of Ba in the leachate increased with the decrease of particle size of the cement composites, and an initial increase in the leaching efficiency of Sn was followed by a clear decline with the leaching time. In addition, kinetic study revealed that the leaching behaviors of potential toxic elements follow a second-order model. The results demonstrated that the addition of washed MSWI fly ash into cement can contribute to the attrition resistance, indicating that the washed MSWI fly ash could be a promising alternative for cement as supplementary building materials.

Hydrothermal carbonization of rice husk for fuel upgrading

NASA Astrophysics Data System (ADS)

Suteerawattananonda, N.; Kongkaew, N.; Patumsawad, S.

2018-01-01

The biomass is popularly used as renewable energy. In Thailand rice is the most consume agricultural products. Agricultural residues from rice husk can be an energy resource. However, alkali and alkali earth materials (AAEMs) in biomass ash are the causes of corrosion and erosion problem in the heat exchanger equipment, while the acidity of ash affects the slagging agglomeration problem. Reduction of alkali and alkali earth materials can minimize the problem. In order to challenge the reduction of alkali and alkali earth materials in biomass ash, hydrothermal carbonization process was selected. Thai rice husk was used as sample to compare the result of treatment. The rice husk was heated under the condition of different temperature ranged from 180°C to 250°C, at operate pressure ranges from 12 bar to 42 bar with residence holding reaction time 1 hour. The results of proximate analysis show that the percentage by mass of fixed carbon are increased 2 times, but volatile matter is decreased by 40% and ash content is decreased by 11% due to the increment of temperature. Meanwhile, the X-Ray fluorescence (XRF) analysis results show the decreasing of alkali and alkali earth materials are reduced.

Evidence of volcanic ash at a K-T boundary section: Ocean drilling program hole 690 C, Maud Rise, Weddell Sea off East Antarctica

NASA Technical Reports Server (NTRS)

Wise, S. W.; Hamilton, N.; Pospichal, J.; Barker, P. F.; Kennett, James P.; Oconnell, S.; Bryant, W. R.; Burckle, L. H.; Egeberg, P. K.; Futterer, D. K.

1988-01-01

Rare vitric volcanogenic ash but more abundant clay minerals considered volcanogenic in origin are associated with an expanded and essentially complete K-T boundary sequence from Ocean Drilling Project (ODP) Hole 690 C on Maud Rise in the Weddell Sea off East Antarctica. Results at this writing are preliminary and are still based to some extent on shipboard descriptions. Further shore-based studies are in progress. It would appear, however, that the presence of volcanic ash and altered ash in the Danian section beginning at the biostratigraphically and paleomagnetically determined K-T boundary on Maud Rise can be cited as evidence of significant volcanic activity within the South Atlantic-Indian Ocean sector of the Southern Ocean coincident with the time of biotic crises at the end of the Maestrichtian. This is a postulated time of tectonic and volcanic activity within this Southern Hemisphere region, including possible initiation of the Reunion hot spot and a peak in explosive volcanism on Walvis Ridge (1) among other events. A causal relationship with the biotic crisis is possible and volcanism should be given serious consideration as a testable working hypothesis to explain these extinctions.

Response of impurity particle confinement time to external actuators in QH-mode plasmas on DIII-D

DOE PAGES

Grierson, Brian A.; Burrell, Keith H.; Garofalo, Andrea M.; ...

2014-11-04

A series of quiescent H-mode discharges have been executed with the specific aim of determining the particle confinement time of impurities in the presence of the edge harmonic oscillation. These discharges utilize non-intrinsic, non-recycling fully-stripped fluorine as the diagnostic species monitored by charge-exchange recombination spectroscopy. It is found that the EHO is an efficient means of impurity expulsion from the core plasma, with impurity exhaust rates comparable to or exceeding those in companion ELMing discharges. Furthermore, as the external torque from neutral beam injection is lowered, the global energy confinement time increases while the impurity confinement time does not displaymore » an increase.« less

Constraints on the Longevity of the 2010 Eyjaföll Eruption Cloud From Analog Experiments and Modeling

NASA Astrophysics Data System (ADS)

Carazzo, G.; Jellinek, M.

2010-12-01

The prolonged disruption of global air travel as a result of the 2010 Eyjafjöll eruption in Iceland underscores the value of discerning the dynamics of volcanic ash-clouds in the atmosphere. Understanding the longevity of these clouds is a particularly long standing problem that bears not only on volcanic hazards to humans but also on the nature and time scale of volcanic forcings on climate change. Since early work on the subject, the common practice to tackle the problem of cloud longevity has been to account for the dynamics of sedimentation by individual particle settling. We use 1D modeling and analog experiments of a turbulent particle-laden umbrella cloud to show that this classical view can be misleading and that the residence times of these ash-clouds in the atmosphere depends strongly on the collective behavior of the solid fraction. Diffusive convection driven by the differential diffusion of constituents altering the cloud density (ash, temperature, sulfur dioxide) may enhance particle scavenging and extend the cloud longevity over time scales orders of magnitude longer than currently expected (i.e., years rather than days for powerful eruptions). Records of this behavior can be found in real-time measurements of stratospheric post-volcanic aerosols following the 1974 Fuego, the 1982 El Chichon, the 1991 Hudson and Pinatubo events, and more recently, from the 14 April 2010 Eyjafjöll eruption. The importance of diffusive convection in volcanic ash-clouds depends strongly on particle size distribution and concentration. For the 2010 Eyjafjöll eruption, we predict that particles larger than 10 microns should settle individually as commonly assumed, but particles smaller than 1 micron should diffuse slowly in layers extending the cloud longevity to several weeks rather than days. These predictions are found to be in good agreement with a number of satellite and ground-based lidar data on ash size and mass estimates performed at different locations across Europe.

Wave function for time-dependent harmonically confined electrons in a time-dependent electric field.

PubMed

Li, Yu-Qi; Pan, Xiao-Yin; Sahni, Viraht

2013-09-21

The many-body wave function of a system of interacting particles confined by a time-dependent harmonic potential and perturbed by a time-dependent spatially homogeneous electric field is derived via the Feynman path-integral method. The wave function is comprised of a phase factor times the solution to the unperturbed time-dependent Schrödinger equation with the latter being translated by a time-dependent value that satisfies the classical driven equation of motion. The wave function reduces to that of the Harmonic Potential Theorem wave function for the case of the time-independent harmonic confining potential.

Academic self-handicapping: relationships with learning specific and general self-perceptions and academic performance over time.

PubMed

Gadbois, Shannon A; Sturgeon, Ryan D

2011-06-01

Academic self-handicapping (ASH) tendencies, strategies students employ that increase their chances of failure on assessments while protecting self-esteem, are correlated with classroom goal structures and to learners' general self-perceptions and learning strategies. In particular, greater ASH is related to poorer academic performance but has yet to be examined with respect to learners' performance across a series of tests. This research was designed to examine the relationship between students' ASH tendencies and their self-concept clarity, learning strategies, and performance on a series of tests in a university course. A total of 209 (153 female; 56 male) Canadian university psychology students participated in this study. Participants' ASH tendencies, self-concept clarity, approaches to learning, and self-regulatory learning strategies were assessed along with expected grades and hours of study in the course from which they were recruited. Finally, students' grades were obtained for the three tests for the course from which they were recruited. Students reporting greater self-handicapping tendencies reported lower self-concept clarity, lower academic self-efficacy, greater test anxiety, more superficial learning strategies, and scored lower on all tests in the course. The relationships of ASH scores and learner variables with performance varied across the three performance indices. In particular, ASH scores were more strongly related to second and third tests, and prior performances were accounted for. ASH scores accounted for a relatively small but significant proportion of variance for all three tests. These results showed that ASH is a unique contributing factor in student performance outcomes, and may be particularly important after students complete the initial assessment in a course. ©2010 The British Psychological Society.

Development of a sintering process for recycling oil shale fly ash and municipal solid waste incineration bottom ash into glass ceramic composite.

PubMed

Zhang, Zhikun; Zhang, Lei; Li, Aimin

2015-04-01

Oil shale fly ash and municipal solid waste incineration bottom ash are industrial and municipal by-products that require further treatment before disposal to avoid polluting the environment. In the study, they were mixed and vitrified into the slag by the melt-quench process. The obtained vitrified slag was then mixed with various percentages of oil shale fly ash and converted into glass ceramic composites by the subsequent sintering process. Differential thermal analysis was used to study the thermal characteristics and determine the sintering temperatures. X-ray diffraction analysis was used to analyze the crystalline phase compositions. Sintering shrinkage, weight loss on ignition, density and compressive strength were tested to determine the optimum preparation condition and study the co-sintering mechanism of vitrified amorphous slag and oil shale fly ash. The results showed the product performances increased with the increase of sintering temperatures and the proportion of vitrified slag to oil shale fly ash. Glass ceramic composite (vitrified slag content of 80%, oil shale fly ash content of 20%, sintering temperature of 1000 °C and sintering time of 2h) showed the properties of density of 1.92 ± 0.05 g/cm(3), weight loss on ignition of 6.14 ± 0.18%, sintering shrinkage of 22.06 ± 0.6% and compressive strength of 67 ± 14 MPa. The results indicated that it was a comparable waste-based material compared to previous researches. In particular, the energy consumption in the production process was reduced compared to conventional vitrification and sintering method. Chemical resistance and heavy metals leaching results of glass ceramic composites further confirmed the possibility of its engineering applications. Copyright © 2015 Elsevier Ltd. All rights reserved.

Volcanic ash and respiratory symptoms in children on the island of Montserrat, British West Indies

PubMed Central

Forbes, L; Jarvis, D; Potts, J; Baxter, P

2003-01-01

Background: In July 1995 the volcano on the West Indian island of Montserrat erupted after being inactive for several hundred years. Since then, clouds of ash have been released intermittently from the volcano. Some of this ash is <10 µm in diameter and therefore respirable. Concerns were raised that the particles might cause respiratory problems. Aims: To evaluate whether ashfalls had any effect on the respiratory health of children in Montserrat. Methods: A survey of asthma diagnoses, respiratory symptoms, exercise induced bronchoconstriction (EIB), and current and previous exposure to volcanic ash was carried out in schools in Montserrat during February 1998. Results: Questionnaire information was available for nearly 80% of the 443 children on the school rolls. The prevalence of wheeze symptoms in the previous 12 months was 18% in children aged 12 years and under and 16% in children aged 13 years and over. In children aged 12 and under, the prevalence of wheeze was greater in those who had ever been heavily or moderately exposed to volcanic ash compared with the group who had only ever been exposed to low levels (wheeze in last 12 months: odds ratio (OR) 4.30; wheeze ever: OR 3.45). The prevalence of EIB in 8–12 year olds was about four times higher in those who were currently heavily exposed to volcanic ash (OR 3.85) compared to those currently exposed to low levels. Conclusions: Volcanic ash emissions adversely affected the respiratory health of Montserrat children. The findings emphasise the need to limit exposures of children to volcanic ash and ensure the appropriate management of respiratory symptoms. PMID:12598669

Thermal and hydrometallurgical recovery methods of heavy metals from municipal solid waste fly ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuboňová, L., E-mail: lenka.kubonova@vsb.cz; Langová, Š.; Nowak, B.

2013-11-15

Highlights: • MSW fly ash was thermally and hydrometallurgically treated to remove heavy metals. • More than 90% of easy volatile heavy metals (Cd and Pb) were removed thermally. • More than 90% of Cd, Cr, Cu an Zn were removed by alkaline – acid leaching. • The best results were obtained for the solution of 3 M NaOH and 2 M H{sub 2}SO{sub 4}. - Abstract: Heavy metals in fly ash from municipal solid waste incinerators are present in high concentrations. Therefore fly ash must be treated as a hazardous material. On the other hand, it may be amore » potential source of heavy metals. Zinc, lead, cadmium, and copper can be relatively easily removed during the thermal treatment of fly ash, e.g. in the form of chlorides. In return, wet extraction methods could provide promising results for these elements including chromium and nickel. The aim of this study was to investigate and compare thermal and hydrometallurgical treatment of municipal solid waste fly ash. Thermal treatment of fly ash was performed in a rotary reactor at temperatures between 950 and 1050 °C and in a muffle oven at temperatures from 500 to 1200 °C. The removal more than 90% was reached by easy volatile heavy metals such as cadmium and lead and also by copper, however at higher temperature in the muffle oven. The alkaline (sodium hydroxide) and acid (sulphuric acid) leaching of the fly ash was carried out while the influence of temperature, time, concentration, and liquid/solid ratio were investigated. The combination of alkaline-acidic leaching enhanced the removal of, namely, zinc, chromium and nickel.« less

Aviation response to a widely dispersed volcanic ash and gas cloud from the August 2008 eruption of Kasatochi, Alaska, USA

USGS Publications Warehouse

Guffanti, Marianne; Schneider, David J.; Wallace, Kristi L.; Hall, Tony; Bensimon, Dov R.; Salinas, Leonard J.

2010-01-01

The extensive volcanic cloud from Kasatochi's 2008 eruption caused widespread disruptions to aviation operations along Pacific oceanic, Canadian, and U.S. air routes. Based on aviation hazard warnings issued by the National Oceanic and Atmospheric Administration, U.S. Geological Survey, the Federal Aviation Administration, and Meteorological Service of Canada, air carriers largely avoided the volcanic cloud over a 5 day period by route modifications and flight cancellations. Comparison of time coincident GOES thermal infrared (TIR) data for ash detection with Ozone Monitoring Instrument (OMI) ultraviolet data for SO2 detection shows congruent areas of ash and gas in the volcanic cloud in the 2 days following onset of ash production. After about 2.5 days, the area of SO2 detected by OMI was more extensive than the area of ash indicated by TIR data, indicating significant ash depletion by fall out had occurred. Pilot reports of visible haze at cruise altitudes over Canada and the northern United States suggested that SO2 gas had converted to sulfate aerosols. Uncertain about the hazard potential of the aging cloud, airlines coped by flying over, under, or around the observed haze layer. Samples from a nondamaging aircraft encounter with Kasatochi's nearly 3 day old cloud contained volcanic silicate particles, confirming that some fine ash is present in predominantly gas clouds. The aircraft's exposure to ash was insufficient to cause engine damage; however, slightly damaging encounters with volcanic clouds from eruptions of Reventador in 2002 and Hekla in 2000 indicate the possibility of lingering hazards associated with old and/or diffuse volcanic clouds.

Application of large volume injection GC-MS to analysis of organic compounds in the extracts and leachates of municipal solid waste incineration fly ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korenkova, Eva; Matisova, Eva; Slobodnik, Jaroslav

2006-07-01

Organic solvent and water extracts of fly ash from a Milan (Italy) municipal solid waste incinerator (MSWI) were analyzed by large volume injection-gas chromatography-mass spectrometry (LVI-GC-MS) with programmable temperature vaporizer (PTV). Using injection volumes of 10-100 {mu}l, typically over a hundred compounds were detected in organic solvent extracts and ca. 35% of them could be tentatively identified from their electron impact ionization mass spectra. A protocol for the determination of the maximum amount of a potential environmental pollutant available for leaching (availability test) was developed for four selected target compounds: pentachlorobenzene (PeCB), hexachlorobenzene (HxCB), o-terphenyl (o-TPH) and m-terphenyl (m-TPH). Keymore » parameters, extraction time and liquid-to-solid ratio (L/S), were studied in more detail. Recoveries of PeCB, HxCB and o-TPH spiked into the fly ash samples at two concentration levels ranged from 38% to 53% for freshly spiked and from 14% to 40% for 40-day aged fly ash. Recoveries of m-TPH were 8% to 11% from freshly spiked and less than 3% from aged spiked fly ash. The native amounts in Milan MSWI fly ash, determined in an interlaboratory exercise using the developed protocol, were 31 ng/g PeCB, 34 ng/g HxCB, 72 ng/g o-TPH and 4.4 ng/g m-TPH. A separate methodology was developed for the determination of compounds extracted from fly ash by water (leaching test). Following 8-h sonication at L/S 20, the leached amounts of PeCB, HxCB and o-TPH were 1.1, 3.1 and 6.0 ng/g fly ash, respectively.« less

Feeding by emerald ash borer larvae induces systemic changes in black ash foliar chemistry.

PubMed

Chen, Yigen; Whitehill, Justin G A; Bonello, Pierluigi; Poland, Therese M

2011-11-01

The exotic wood-boring pest, emerald ash borer (EAB), Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), has been threatening North American ash (Fraxinus spp.) resources, this being recognized since its first detection in Michigan, USA and Ontario, Canada in 2002. Ash trees are killed by larval feeding in the cambial region, which results in disruption of photosynthate and nutrient translocation. In this study, changes in volatile and non-volatile foliar phytochemicals of potted 2-yr-old black ash, Fraxinus nigra Marshall, seedlings were observed in response to EAB larval feeding in the main stem. EAB larval feeding affected levels of six compounds [hexanal, (E)-2-hexenal, (Z)-3-hexenyl acetate, (E)-β-ocimene, methyl salicylate, and (Z,E)-α-farnesene] with patterns of interaction depending upon compounds of interest and time of observation. Increased methyl salicylate emission suggests similarity in responses induced by EAB larval feeding and other phloem-feeding herbivores. Overall, EAB larval feeding suppressed (Z)-3-hexenyl acetate emission, elevated (E)-β-ocimene emission in the first 30days, but emissions leveled off thereafter, and generally increased the emission of (Z,E)-α-farnesene. Levels of carbohydrates and phenolics increased overall, while levels of proteins and most amino acids decreased in response to larval feeding. Twenty-three amino acids were consistently detected in the foliage of black ash. The three most abundant amino acids were aspartic acid, glutamic acid, glutamine, while the four least abundant were α-aminobutyric acid, β-aminoisobutyric acid, methionine, and sarcosine. Most (16) foliar free amino acids and 6 of the 9 detected essential amino acids decreased with EAB larval feeding. The ecological consequences of these dynamic phytochemical changes on herbivores harbored by ash trees and potential natural enemies of these herbivores are discussed. Copyright © 2011 Elsevier Ltd. All rights reserved.

Chemical associations and mobilization of heavy metals in fly ash from municipal solid waste incineration.

PubMed

Weibel, Gisela; Eggenberger, Urs; Schlumberger, Stefan; Mäder, Urs K

2017-04-01

This study focusses on chemical and mineralogical characterization of fly ash and leached filter cake and on the determination of parameters influencing metal mobilization by leaching. Three different leaching processes of fly ash from municipal solid waste incineration (MSWI) plants in Switzerland comprise neutral, acidic and optimized acidic (+ oxidizing agent) fly ash leaching have been investigated. Fly ash is characterized by refractory particles (Al-foil, unburnt carbon, quartz, feldspar) and newly formed high-temperature phases (glass, gehlenite, wollastonite) surrounded by characteristic dust rims. Metals are carried along with the flue gas (Fe-oxides, brass) and are enriched in mineral aggregates (quartz, feldspar, wollastonite, glass) or vaporized and condensed as chlorides or sulphates. Parameters controlling the mobilization of neutral and acidic fly ash leaching are pH and redox conditions, liquid to solid ratio, extraction time and temperature. Almost no depletion for Zn, Pb, Cu and Cd is achieved by performing neutral leaching. Acidic fly ash leaching results in depletion factors of 40% for Zn, 53% for Cd, 8% for Pb and 6% for Cu. The extraction of Pb and Cu are mainly limited due to a cementation process and the formation of a PbCu 0 -alloy-phase and to a minor degree due to secondary precipitation (PbCl 2 ). The addition of hydrogen peroxide during acidic fly ash leaching (optimized acidic leaching) prevents this reduction through oxidation of metallic components and thus significantly higher depletion factors for Pb (57%), Cu (30%) and Cd (92%) are achieved. The elevated metal depletion using acidic leaching in combination with hydrogen peroxide justifies the extra effort not only by reduced metal loads to the environment but also by reduced deposition costs. Copyright © 2016 Elsevier Ltd. All rights reserved.

Co-composting of biowaste and wood ash, influence on a microbially driven-process.

PubMed

Fernández-Delgado Juárez, Marina; Prähauser, Barbara; Walter, Andreas; Insam, Heribert; Franke-Whittle, Ingrid H

2015-12-01

A trial at semi-industrial scale was conducted to evaluate the effect of wood ash amendment on communal biowaste in a composting process and on the final composts produced. For this purpose, three treatments including an unamended control (C0) and composts with additions of 6% (C6), and 12% (C12) of wood ash (w/w) were studied, and physico-chemical parameters as well as microbial activity and community composition were investigated. At the end of the process, composts were tested for toxicity and quality, and microbial physiological activity. The influence of ash addition on compost temperature, pH, microbial activity and composition was stronger during the early composting stages and diminished with time, whereby composts became more similar. Using the COMPOCHIP microarray, a reduction in the pathogenic genera Listeria and Clostridium was observed, which together with the temperature increases of the composting process helped in the hygienisation of composts. Lactobacillus species were also affected, such that reduced hybridisation signals were observed with increased ash addition, due to the increased pH values in amended composts. Organic matter mineralisation was also increased through ash addition, and no negative effects on the composting process were observed. The nutrient content of the final products was increased through the addition of ash, and no toxic effects were observed. Nonetheless, greater concentrations of heavy metals were found in composts amended with more ash, which resulted in a downgrading of the compost quality according to the Austrian Compost Ordinance. Thus, regulation of both input materials and end-product quality is essential in optimising composting processes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Optimization of fly ash as sand replacement materials (SRM) in cement composites containing coconut fiber

NASA Astrophysics Data System (ADS)

Nadzri, N. I. M.; Jamaludin, S. B.; Mazlee, M. N.; Jamal, Z. A. Z.

2016-07-01

The need of utilizing industrial and agricultural wastes is very important to maintain sustainability. These wastes are often incorporated with cement composites to improve performances in term of physical and mechanical properties. This study presents the results of the investigation of the response of cement composites containing coconut fiber as reinforcement and fly ash use as substitution of sand at different hardening days. Hardening periods of time (7, 14 and 28 days) were selected to study the properties of cement composites. Optimization result showed that 20 wt. % of fly ash (FA) is a suitable material for sand replacement (SRM). Meanwhile 14 days of hardening period gave highest compressive strength (70.12 MPa) from the cement composite containing 9 wt. % of coconut fiber and fly ash. This strength was comparable with the cement without coconut fiber (74.19 MPa) after 28 days of curing.

Volcanic ash plume identification using polarization lidar: Augustine eruption, Alaska

USGS Publications Warehouse

Sassen, Kenneth; Zhu, Jiang; Webley, Peter W.; Dean, K.; Cobb, Patrick

2007-01-01

During mid January to early February 2006, a series of explosive eruptions occurred at the Augustine volcanic island off the southern coast of Alaska. By early February a plume of volcanic ash was transported northward into the interior of Alaska. Satellite imagery and Puff volcanic ash transport model predictions confirm that the aerosol plume passed over a polarization lidar (0.694 mm wavelength) site at the Arctic Facility for Atmospheric Remote Sensing at the University of Alaska Fairbanks. For the first time, lidar linear depolarization ratios of 0.10 – 0.15 were measured in a fresh tropospheric volcanic plume, demonstrating that the nonspherical glass and mineral particles typical of volcanic eruptions generate strong laser depolarization. Thus, polarization lidars can identify the volcanic ash plumes that pose a threat to jet air traffic from the ground, aircraft, or potentially from Earth orbit.

Applications of the PUFF model to forecasts of volcanic clouds dispersal from Etna and Vesuvio

NASA Astrophysics Data System (ADS)

Daniele, P.; Lirer, L.; Petrosino, P.; Spinelli, N.; Peterson, R.

2009-05-01

PUFF is a numerical volcanic ash tracking model developed to simulate the behaviour of ash clouds in the atmosphere. The model uses wind field data provided by meteorological models and adds dispersion and sedimentation physics to predict the evolution of the cloud once it reaches thermodynamic equilibrium with the atmosphere. The software is intended for use in emergency response situations during an eruption to quickly forecast the position and trajectory of the ash cloud in the near (˜1-72 h) future. In this paper, we describe the first application of the PUFF model in forecasting volcanic ash dispersion from the Etna and Vesuvio volcanoes. We simulated the daily occurrence of an eruptive event of Etna utilizing ash cloud parameters describing the paroxysm of 22nd July 1998 and wind field data for the 1st September 2005-31st December 2005 time span from the Global Forecast System (GFS) model at the approximate location of the Etna volcano (38N 15E). The results show that volcanic ash particles are dispersed in a range of directions in response to changing wind field at various altitudes and that the ash clouds are mainly dispersed toward the east and southeast, although the exact trajectory is highly variable, and can change within a few hours. We tested the sensitivity of the model to the mean particle grain size and found that an increased concentration of ash particles in the atmosphere results when the mean grain size is decreased. Similarly, a dramatic variation in dispersion results when the logarithmic standard deviation of the particle-size distribution is changed. Additionally, we simulated the occurrence of an eruptive event at both Etna and Vesuvio, using the same parameters describing the initial volcanic plume, and wind field data recorded for 1st September 2005, at approximately 38N 15E for Etna and 41N 14E for Vesuvio. The comparison of the two simulations indicates that identical eruptions occurring at the same time at the two volcanic centres display significantly different dispersal axes as a consequence of the different local wind field acting at the respective eruptive vents. At the Vesuvio the volcano, a plinian eruptive event with the dynamical parameters of the 79 A.D. eruption was simulated daily for one year, from 1st July 2005 to 30th June 2006. The statistical processing of results points out that, although in most cases the ash cloud dispersal encompasses many different areas, generally the easterly southeasterly direction is preferred. Our results highlight the significant role of wind field trends in influencing the distribution of ash particles from eruptive columns and prove that the dynamical parameters that most influence the variability of plume dispersal are the duration of the eruption and the maximum column height. Finally, the possible use of cloud simulations for refining hazard maps of areas exposed to volcanic ash dispersal is proposed.

Optimization of hydrothermal synthesis of pure phase zeolite Na-P1 from South African coal fly ashes.

PubMed

Musyoka, Nicholas M; Petrik, Leslie F; Gitari, Wilson M; Balfour, Gillian; Hums, Eric

2012-01-01

This study was aimed at optimizing the synthesis conditions for pure phase zeolite Na-P1 from three coal fly ashes obtained from power stations in the Mpumalanga province of South Africa. Synthesis variables evaluated were: hydrothermal treatment time (12-48 hours), temperature (100-160°C) and varying molar quantities of water during the hydrothermal treatment step (H(2)O:SiO(2) molar ratio ranged between 0-0.49). The optimum synthesis conditions for preparing pure phase zeolite Na-P1 were achieved when the molar regime was 1 SiO(2): 0.36 Al(2)O(3): 0.59 NaOH: 0.49 H(2)O and ageing was done at 47°C for 48 hours. The optimum hydrothermal treatment time and temperature was 48 hours and 140°C, respectively. Fly ashes sourced from two coal-fired power plants (A, B) were found to produce nearly same high purity zeolite Na-P1 under identical conditions whereas the third fly ash (C) lead to a low quality zeolite Na-P1 under these conditions. The cation exchange capacity for the high pure phase was found to be 4.11 meq/g. These results highlight the fact that adjustment of reactant composition and presynthesis or synthesis parameters, improved quality of zeolite Na-P1 can be achieved and hence an improved potential for application of zeolites prepared from coal fly ash.

Preparation, Characterization of Coal Ash Adsorbent and Orthogonal Experimental Rsearch on Treating Printing and Dyeing Wastewater

NASA Astrophysics Data System (ADS)

Wang, Qingyu; He, Lingfeng; Shi, Liang; Chen, Xiaogang; Chen, Xin; Xu, Zizhen; Zhang, Yongli

2018-03-01

Using high temperature activated sodium flying ash and carboxymethyl chitosan as raw material to prepare carboxymethylchitosan wrapping fly-ash adsorbent (CWF), combined with iron-carbon micro-electrolysis treatment of simulated and actual printing and dyeing wastewater. The conditions for obtaining are from the literature: the best condition for CWF to treat simulated printing and dyeing wastewater pretreated with iron-carbon micro-electrolysis is that the mixing time is 10min, the resting time is 30 min, pH=6, and the adsorbent dosage is 0.75 g/L. The results showed that COD removal efficiency and decoloration rate were above 97 %, and turbidity removal rate was over 90 %. The optimum dyeing conditions were used to treat the dyeing wastewater. The decolorization rate was 97.30 %, the removal efficiency of COD was 92.44 %, and the turbidity removal rate was 90.37 %.

The phosphorus status of andisols as influenced by nanoparticles of volcanic ash and rock phosphate

NASA Astrophysics Data System (ADS)

Devnita, Rina; Joy, Benny; Arifin, Mahfud; Setiawan, Ade; Rosniawaty, Santi; Meidina, Felia Shella

2018-02-01

Andisols need to be ameliorated to improve the phosphorus status. The objective of this research is to investigate the effect of nanoparticles of volcanic ash and rock phosphate as ameliorants in Andisols to P-retention, available P and potential P in Andisols. The research used a complete randomized experimental design in factorial with two factors. The first factor was nanoparticle of volcanic ash (a) and the second factor was rock phosphate (p). Both ameliorants consist of four doses on soil weight percentage (0%, 2.5%, 5.0% and 7.5%). The combined treatments were replicated three times. The soil and treatments were mixed and incubated for 4 months. Soil samples were taken after one month and four months of incubation to be analyzed the P-retention, available P and potential P. The results showed that there are interactions between the volcanic ash and rock phosphate on available P and potential P after one month of incubation. However, there were no interactions occurring between the volcanic ash and rock phosphate on P-retention after one and four months of incubation and no interactions on available P and potential P after four months. The best combined treatments in increasing available P and potential P after one month was obtained in 2.5% of volcanic ash and 5% of rock phosphate that increased available P to 405.75 ppm. The 2.5% of volcanic ash and 7.5% of rock phosphate increased potential P to 2190.26 mg/100 g. Independently, 7.5% of volcanic ash and rock phosphate decreased P-retention to 71.49% after one month and 89.74% after four months. Higher effect on the application of nanoparticle of volcanic ash and rock phosphate to the phosphorus status of Andisols recieved after one month of incubation is compared with four months of incubation.

The 1815 Tambora ash fall: implications for transport and deposition of distal ash on land and in the deep sea

NASA Astrophysics Data System (ADS)

Kandlbauer, Jessica; Carey, Steven N.; Sparks, R. Stephen J.

2013-04-01

Tambora volcano lies on the Sanggar Peninsula of Sumbawa Island in the Indonesian archipelago. During the great 1815 explosive eruption, the majority of the erupted pyroclastic material was dispersed and subsequently deposited into the Indian Ocean and Java Sea. This study focuses on the grain size distribution of distal 1815 Tambora ash deposited in the deep sea compared to ash fallen on land. Grain size distribution is an important factor in assessing potential risks to aviation and human health, and provides additional information about the ash transport mechanisms within volcanic umbrella clouds. Grain size analysis was performed using high precision laser diffraction for a particle range of 0.2 μm-2 mm diameter. The results indicate that the deep-sea samples provide a smooth transition to the land samples in terms of grain size distributions despite the different depositional environments. Even the very fine ash fraction (<10 μm) is deposited in the deep sea, suggesting vertical density currents as a fast and effective means of transport to the seafloor. The measured grain size distribution is consistent with an improved atmospheric gravity current sedimentation model that takes into account the finite duration of an eruption. In this model, the eruption time and particle fall velocity are the critical parameters for assessing the ash component depositing while the cloud advances versus the ash component depositing once the eruption terminates. With the historical data on eruption duration (maximum 24 h) and volumetric flow rate of the umbrella cloud (˜1.5-2.5 × 1011 m3/s) as input to the improved model, and assuming a combination of 3 h Plinian phase and 21 h co-ignimbrite phase, it reduces the mean deviation of the predicted versus observed grain size distribution by more than half (˜9.4 % to ˜3.7 %) if both ash components are considered.

Experimental investigation of ash deposits on convection heating surfaces of a circulating fluidized bed municipal solid waste incinerator.

PubMed

Tang, Zhi; Chen, Xiaoping; Liu, Daoyin; Zhuang, Yaming; Ye, Minghua; Sheng, Hongchan; Xu, Shaojuan

2016-10-01

Incineration of municipal solid waste (MSW) is a waste treatment method which can be sustainable in terms of waste volume reduction, as well as a source of renewable energy. During MSW combustion, increased formation of deposits on convection heating exchanger surfaces can pose severe operational problems, such as fouling, slagging and corrosion. These problems can cause lower heat transfer efficiency from the hot flue gas to the working fluid inside the tubes. A study was performed where experiments were carried out to examine the ash deposition characteristics in a full-scale MSW circulating fluidized bed (CFB) incinerator, using a newly designed deposit probe that was fitted with six thermocouples and four removable half rings. The influence of probe exposure time and probe surface temperature (500, 560, and 700°C) on ash deposit formation rate was investigated. The results indicate that the deposition mass and collection efficiency achieve a minimum at the probe surface temperature of 560°C. Ash particles are deposited on both the windward and leeward sides of the probe by impacting and thermophoretic/condensation behavior. The major inorganic elements present in the ash deposits are Ca, Al and Si. Compared to ash deposits formed on the leeward side of the probe, windward-side ash deposits contain relatively higher Ca and S concentrations, but lower levels of Al and Si. Among all cases at different surface temperatures, the differences in elemental composition of the ash deposits from the leeward side are insignificant. However, as the surface temperature increases, the concentrations of Al, Si, K and Na in the windward-side ash deposits increase, but the Ca concentration is reduced. Finally, governing mechanisms are proposed on the basis of the experimental data, such as deposit morphology, elemental composition and thermodynamic calculations. Copyright © 2016. Published by Elsevier B.V.

Barometric response functions from borehole water level records and quantification of aquifer vulnerability

NASA Astrophysics Data System (ADS)

Odling, N. E.; Serrano, R. P.; Hussein, M.; Guadagnini, A.; Riva, M.

2013-12-01

In confined and semi-confined aquifers, borehole water levels respond to fluctuations in barometric pressure and this response can be used to estimate the properties of aquifer confining layers. We use this response as indicator of groundwater vulnerability for the semi-confined Chalk aquifer in East Yorkshire, UK. Time series data of borehole water levels are corrected for Earth tides and recharge, and barometric response functions (BRFs) estimated using cross-spectral deconvolution-averaging techniques. The resulting BRFs are fitted using a theoretical model of the BRF gain and phase for a semi-confined aquifer (Rojstaczer, 1988) to obtain confining layer properties. For all of the boreholes, non-zero hydraulic diffusivities for the confining layer were found indicating that the aquifer is semi-confined. A ';characteristic time scale' based on the hydraulic and pneumatic diffusivities of the confining layer is introduced as a measure of the degree of aquifer confinement and therefore groundwater vulnerability. The analytical model assumes that the confining layer and aquifer are homogeneous. However, in nature, confining layers are heterogeneous and groundwater vulnerability dominated by the presence of high diffusivity, high flow pathways through the confining layer to the aquifer. A transient numerical model (MODFLOW) was constructed to test the impact of such heterogeneities on the BRF. In the model, an observed barometric pressure time series is used as a boundary condition applied to the upper surface of the top unit of the model (representing the confining layer) and BRFs determined from the time series of model heads in the bottom unit (representing the aquifer). The results from a numerical model with a homogeneous confining layer were found to accurately reproduce the BRFs from a modified version of the analytical model. The introduction of a localized, high diffusive block in the confining layer was found to modify the BRF, reducing the gain amplitude while having limited impact on the phase. It was found that the BRF reflects the presence of a fully penetrating, high diffusivity heterogeneity up to several hundred meters distant from the observation borehole, and shows little sensitivity to the heterogeneity's horizontal dimension. Heterogeneities that are 50% partially penetrating do not significantly impact on the BRF and 90% penetrating heterogeneities can only be detected when large and close to the observation borehole. These results show that BRF gain may be particularly useful in detecting the presence of fully penetrating heterogeneities of high diffusivity within confining layers that potentially enhance groundwater vulnerability. This research has been funded in part through the EU ITN ';IMVUL' (PITN-GA-2008-212298). Reference: Rojstaczer, S. (1988) Determination of fluid-flow properties from the response of water levels in wells to atmospheric loading, Water Resources Research, 24(11), 1927-1938.

Chemical and radiological characterization of fly and bottom ash landfill of the former sulfate pulp factory Plaški and its surroundings.

PubMed

Oreščanin, Višnja; Kollar, Robert; Buben, Kresimir; Mikelic, Ivanka Lovrencic; Kollar, Karlo; Kollar, Melkior; Medunic, Gordana

2012-01-01

The subject of this study was chemical and radiological characterization of the fly and bottom ash, by-product of the combustion of coal used as an energy source in the former sulfate pulp factory in Plaški. The research involves determination of the concentration of macro, micro and trace elements and activities of the radionuclides in: (i) ash from different positions of the landfill; (ii) soil samples in the zone of the influence of the landfill; (iii) control soil samples and (iv) sediment sample from the river Dretulja. Besides, in situ measurement of an effective dose rate above ash/soil was also determined. In relation with the control soil the average increase of the concentrations of the elements Ca, Cd, Hg, Ni, Se, Sr, Th and U in the samples taken from the fly and bottom ash landfill as well as soil samples within the radius of 300 m from the landfill was 38.3, 6.7, 9.9, 8.5, 9.4, 7.2, 3.6 and 5.7 times, respectively. In these samples, the concentrations of the above mentioned elements were in the following ranges: calcium from 7.94 to 19.7 %; cadmium from 0.33 to 1.66 mg/kg; mercury from 0.18 to 0.49 mg/kg; nickel from 260 to 1500 mg/kg; selenium from 2.7 to 21 mg/kg; strontium from 176 to 542 mg/kg; thorium from 8 to 55 mg/kg and uranium from 5.6 to 19.7 mg/kg. Compared to the world's average soil concentration, uranium and thorium values increased 3.7 and 1.7 times, respectively. The mean value of the total effective dose rate measured in the air at the height of 1 m for all samples of ash and soil under the influence of the landfill was 1.60 mSv/yr. Compared to the Croatian average (0.7015 mSv/yr), the determined mean value for the Plaški landfill is two times higher. However, compared to the local background (0.14 mSv/yr), the mean value of the total effective dose rate measured above the Plaški landfill is 11.4 times higher. In the samples of ash and contaminated soil regardless of the sampling location the activity concentrations of the radionuclides in Bq/kg vary in the following ranges: (226)Ra from 82.10 to 314.90 (mean value 145.99), (232)Th from 32.50 to 223.60 (mean value 76.76) and (238)U from 69.10 to 243.20 (mean value 134.38). Compared to the mean values found in the background soil (226)Ra and (238)U mean activity concentrations increased from 1.6 to 6.4 times and (232)Th from 1.4 to 4.3 times. In order to reduce total effective dose rate to the local "background" values and to prevent redistribution of the radionuclides and heavy metals from the deposited material into the environment fly and bottom ash landfill must be sealed with 10 cm thick layer of the material with low permeability.

Classical impurity ion confinement in a toroidal magnetized fusion plasma.

PubMed

Kumar, S T A; Den Hartog, D J; Caspary, K J; Magee, R M; Mirnov, V V; Chapman, B E; Craig, D; Fiksel, G; Sarff, J S

2012-03-23

High-resolution measurements of impurity ion dynamics provide first-time evidence of classical ion confinement in a toroidal, magnetically confined plasma. The density profile evolution of fully stripped carbon is measured in MST reversed-field pinch plasmas with reduced magnetic turbulence to assess Coulomb-collisional transport without the neoclassical enhancement from particle drift effects. The impurity density profile evolves to a hollow shape, consistent with the temperature screening mechanism of classical transport. Corroborating methane pellet injection experiments expose the sensitivity of the impurity particle confinement time to the residual magnetic fluctuation amplitude.

Interspecific variation in resistance to emerald ash borer (Coleoptera: Buprestidae) among North American and Asian ash (Fraxinus spp.).

PubMed

Rebek, Eric J; Herms, Daniel A; Smitley, David R

2008-02-01

We conducted a 3-yr study to compare the susceptibility of selected North American ash and an Asian ash species to emerald ash borer, Agrilus planipennis Fairmaire, an invasive wood-boring beetle introduced to North America from Asia. Because of a coevolutionary relationship between Asian ashes and emerald ash borer, we hypothesized an Asian ash species, Manchurian ash, is more resistant to the beetle than its North American congeners. Consistent with our hypothesis, Manchurian ash experienced far less mortality and yielded far fewer adult beetles than several cultivars of North American green and white ash. Surprisingly, a black ash (North American) x Manchurian ash hybrid was highly susceptible to emerald ash borer, indicating this cultivar did not inherit emerald ash borer resistance from its Asian parent. A corollary study investigated the efficacy of soil-applied imidacloprid, a systemic, neonicotinoid insecticide, for controlling emerald ash borer in each of the five cultivars. Imidacloprid had no effect on emerald ash borer colonization of Manchurian ash, which was low in untreated and treated trees. In contrast, imidacloprid did enhance survival of the North American and hybrid cultivars and significantly reduced the number of emerald ash borer adults emerging from green and white ash cultivars. We identify a possible mechanism of resistance of Manchurian ash to emerald ash borer, which may prove useful for screening, selecting, and breeding emerald ash borer-resistant ash trees.

May 2011 eruption of Telica Volcano, Nicaragua: Multidisciplinary observations

NASA Astrophysics Data System (ADS)

Witter, M. R.; Geirsson, H.; La Femina, P. C.; Roman, D. C.; Rodgers, M.; Muñoz, A.; Morales, A.; Tenorio, V.; Chavarria, D.; Feineman, M. D.; Furman, T.; Longley, A.

2011-12-01

Telica volcano, an andesitic stratovolcano in north-western Nicaragua, erupted in May 2011. The eruption, produced ash but no lava and required the evacuation of over 500 people; no injuries were reported. We present the first detailed report of the eruption, using information from the TElica Seismic ANd Deformation (TESAND) network, that provides real-time data, along with visual observations, ash leachate analysis, and fumarole temperature measurements. Telica is located in the Maribios mountain range. It is one of the most active volcanoes in Nicaragua and has frequent small explosions and rare large (VEI 4) eruptions, with the most recent sizable eruptions (VEI 2) occurring in 1946 and 1999. The 2011 eruption is the most explosive since 1999. The eruption consisted of a series of ash explosions, with the first observations from May 8, 2011 when local residents reported ash fall NE of the active crater. Popping sounds could be heard coming from the crater on May 10. On May 13, the activity intensified and continued with some explosions every day for about 2 weeks. The well-defined plumes originated from the northern part of the crater. Ash fall was reported 4 km north of the active crater on May 14. The largest explosion at 2:54 pm (local time) on May 21 threw rocks from the crater and generated a column 2 km in height. Fresh ash samples were collected on May 16, 18, and 21 and preliminary inspection shows that the majority of the material is fragmented rock and crystalline material, i.e. not juvenile. Ash leachates (ash:water = 1:25) contain a few ppb As, Se, and Cd; tens of ppb Co and Ni; and up to a few hundred ppb Cu and Zn. Telica typically has hundreds of small seismic events every day, even when the volcano is not erupting. The TESAND network detected an increase in the rate and magnitude of seismic activity, with a maximum magnitude of 3.3. Elevated fumarole temperatures at locations near the active vent were also observed throughout the May 2011 eruption. Temperature measurements taken on May 26 recorded a maximum of 539°C. Ten continuous GPS stations running on and close to the volcano showed little deformation, suggesting that substantial quantities of new magma were not displaced beneath the volcanic edifice.

Use of isotopic and hydrometric monitoring methods to partition hydrologic contributions to forested wetlands in the Upper Peninsula of Michigan

NASA Astrophysics Data System (ADS)

Van Grinsven, M. J.; Pypker, T. G.; Kolka, R. K.

2012-12-01

As a result of their landscape position and physical soil properties, northern forested wetlands are capable of retaining springtime snowmelt, rain and near surface groundwater inputs into the growing season. Hydrological conditions such as source water chemistry, duration of inundation, and magnitude of water table fluctuations are affected by the relative contribution of snow, rain, and groundwater sources, and in turn these hydrological conditions strongly influence the structure and function of northern forested wetlands. Black ash (Fraxinus nigra) is a facultative wet tree species, and is known to occur in 23 U.S. states and 7 Canadian provinces in northeastern North America. Black ash trees have ecological, economic, and cultural significance, and are currently threatened by the rapid expansion of the exotic emerald ash borer (Burprestidae: Agrilus planipennis). Since its initial detection in 2002 near Detroit, MI, the emerald ash borer has killed millions of ash trees in 15 U.S. states and 2 Canadian provinces. There is very little known about black ash wetland hydrology and ecology, and as a result of the looming infestation, there is a critical need to gain a better understanding of the hydrology in undisturbed ecosystems. The main objective of this study is to partition source water contributions in black ash wetlands in the western Upper Peninsula of Michigan. We hypothesize that snowmelt and near surface groundwater supply the majority of water to these wetlands annually, and summer rain is readily removed from the system through the evapotranspiration pathway. Hydrometric monitoring methods were used in conjunction with isotopic analysis using a linear mixing model to characterize source water contributions in nine black ash wetlands. The results suggest a connection with near surface groundwater during spring and early summer, and a short residence time for rain water following summer storm events. The outcome of this research aims to inform land managers in northeastern North America about the natural hydrologic condition of black ash wetlands, and provide baseline data that underscores potential water and forest resource impacts of current and future emerald ash borer infestations.

Hierarchical zeolites from class F coal fly ash

NASA Astrophysics Data System (ADS)

Chitta, Pallavi

Fly ash, a coal combustion byproduct is classified as types class C and class F. Class C fly ash is traditionally recycled for concrete applications and Class F fly ash often disposed in landfills. Class F poses an environmental hazard due to disposal and leaching of heavy metals into ground water and is important to be recycled in order to mitigate the environmental challenges. A major recycling option is to reuse the fly ash as a low-cost raw material for the production of crystalline zeolites, which serve as catalysts, detergents and adsorbents in the chemical industry. Most of the prior literature of fly ash conversion to zeolites does not focus on creating high zeolite surface area zeolites specifically with hierarchical pore structure, which are very important properties in developing a heterogeneous catalyst for catalysis applications. This research work aids in the development of an economical process for the synthesis of high surface area hierarchical zeolites from class F coal fly ash. In this work, synthesis of zeolites from fly ash using classic hydrothermal treatment approach and fusion pretreatment approach were examined. The fusion pretreatment method led to higher extent of dissolution of silica from quartz and mullite phases, which in turn led to higher surface area and pore size of the zeolite. A qualitative kinetic model developed here attributes the difference in silica content to Si/Al ratio of the beginning fraction of fly ash. At near ambient crystallization temperatures and longer crystallization times, the zeolite formed is a hierarchical faujasite with high surface area of at least 360 m2/g. This work enables the large scale recycling of class F coal fly ash to produce zeolites and mitigate environmental concerns. Design of experiments was used to predict surface area and pore sizes of zeolites - thus obviating the need for intense experimentation. The hierarchical zeolite catalyst supports tested for CO2 conversion, yielded hydrocarbons up to C9, a performance attesting the hierarchal pore structure. The preliminary techno-economic feasibility assessment demonstrates a net energy saving of 75% and cost saving of 63% compared to the commercial zeolite manufacturing process.

Detection and Tracking of Volcanic Ash and SO2 and its Impact to Aviation

NASA Astrophysics Data System (ADS)

Osiensky, J.; Hall, T.

2008-12-01

The eruptions of Okmok and Kasatochi Volcanoes in August 2008 produced a combination of volcanic ash and SO2 (sulfur dioxide) that impacted aviation across Alaska and the North Pacific Region. The Anchorage Volcanic Ash Advisory Center (A-VAAC) worked closely with the Alaska Volcano Observatory (AVO) and Federal Aviation Administration (FAA) Air Route Traffic Control Center (ARTCC) to ensure that accurate and timely detection and forecast of the ash plume occurred. Volcanic ash poses a hazard to all forms of transportation, but has been shown to be especially dangerous to aviation. Even a small eruption with limited vertical extent to the ash cloud impacts aviation traffic. A significant eruption where the ash cloud penetrates the jet airways (greater than 20,000 feet) requires major re-routing of air traffic, or even the cancellation of flights to ensure the safety of the airways. The AAWU and the AVO have demonstrated substantial experience successfully tracking volcanic ash clouds during the past 15 years. The AAWU issues special aviation warnings for volcanic ash (Volcanic Ash SIGMETs (Significant Meteorological Information)) to warn aircraft of impending ash hazards. However, an additional potential hazard to aviation associated with volcanic eruptions is being examined. A Sulfur Dioxide (SO2) cloud was identified and tracked across the Aleutians, Gulf of Alaska, and eventually into the Lower 48 states. The size and coverage of the SO2 clouds from the Okmok and Kasatochi eruptions may be unprecedented. There are currently no requirements to advise, or warn for SO2 as a hazard to aviation. However, SO2 has been demonstrated as a marker for potential areas of lower concentration volcanic ash. Dispersion models, such as NOAAs HYSPLIT, that are used to track volcanic ash are currently not tuned to track gases such as SO2. SO2 may not be a direct hazard to aviation per se; However, SO2 mixed with water produces H2SO4 (sulfuric acid), and long term exposure to even low concentrations of sulfuric acid may lead to deterioration of airframe paint and acrylic aircraft windows as well as sulfate deposits in the engines. Airlines typically avoid SO2 clouds because these clouds often contain small amounts of ash as well. Relatively new OMI (Ozone Monitoring Instrument) data from the EOS-Aura satellite provides a much higher resolution depiction of the SO2 cloud; However, a major drawback to this capability is that the OMI sensor is located on a Polar Orbiter satellite (where the frequency of this data is sparse). Forecasters in Alaska typically receive only one pass per day from the OMI due to its orbital path. Additional research is needed to better define thresholds and impacts of volcanic ash and SO2 as it relates to aviation. More importantly this research must be transferred rapidly from the research community into forecast operations.

Characterization of fine volcanic ash from explosive eruption from Sakurajima volcano, South Japan

NASA Astrophysics Data System (ADS)

Nanayama, F.; Furukawa, R.; Ishizuka, Y.; Yamamoto, T.; Geshi, N.; Oishi, M.

2013-12-01

Explosive volcanic eruptions can affect infrastructure and ecosystem by their dispersion of the volcanic particle. Characterization of volcanic particle expelled by explosive eruption is crucial for evaluating for quantitative hazard assessment by future volcanic eruption. Especially for fine volcanic ash less than 64 micron in diameter, it can disperse vast area from the source volcano and be easily remobilized by surface wind and precipitation after the deposition. As fine volcanic ash is not preserved well at the earth surface and in strata except for enormously large scale volcanic eruption. In order to quantify quantitative characteristics of fine volcanic ash particle, we sampled volcanic ash directly falling from the eruption cloud from Showa crater, the most active vent of Sakurajima volcano, just before landing on ground. We newly adopted high precision digital microscope and particle grain size analyzer to develop hazard evaluation method of fine volcanic ash particle. Field survey was performed 5 sequential days in January, 2013 to take tamper-proof volcanic ash samples directly obtained from the eruption cloud of the Sakurajima volcano using disposable paper dishes and plastic pails. Samples were taken twice a day with time-stamp in 40 localities from 2.5 km to 43 km distant from the volcano. Japan Meteorological Agency reported 16 explosive eruptions of vulcanian style occurred during our survey and we took 140 samples of volcanic ash. Grain size distribution of volcanic ash was measured by particle grain size analyzer (Mophologi G3S) detecting each grain with parameters of particle diameter (0.3 micron - 1 mm), perimeter, length, area, circularity, convexity, solidity, and intensity. Component of volcanic ash was analyzed by CCD optical microscope (VHX-2000) which can take high resolution optical image with magnifying power of 100-2500. We discriminated each volcanic ash particle by color, texture of surface, and internal structure. Grain size distributions of volcanic ash from Sakurajima volcano have basically characteristics of unimodal and gaussian. Mode of distributions are 150 - 200 micron at 5 km and 70-80 micron at 20 km respectively from the Showa crater. Mode and deviation of the grain size distribution are function of distance from the source. Fine volcanic ash less than 1 micron in diameter is few and exists in every samples. Component of volcanic ash samples are dark-colored dense glass shard (ca. 50%), light-colored dense glass shard (10%), variously colored and vesiculated glass shard (10%), free crystal (20%), lithic fragment (10%), and altered fragment (less than 5%) which are mostly having similar ratio in every location suggesting single source process of the eruption. We also found fine volcanic ash samples less than 10 micron are frequently aggregated. The present study includes the result of "Research and Development of Margin Assessment Methodology of Decay Heat Removal Function against External Hazards" entrusted to Japan Atomic Energy Agency by the Ministry of Education, Culture, Sports, Science and Technology of Japan (MEXT).

Devolatilization of oil sludge in a lab-scale bubbling fluidized bed.

PubMed

Liu, Jianguo; Jiang, Xiumin; Han, Xiangxin

2011-01-30

Devolatilization of oil sludge pellets was investigated in nitrogen and air atmosphere in a lab-scale bubbling fluidized bed (BFB). Devolatilization times were measured by the degree of completion of the evolution of the volatiles for individual oil sludge pellets in the 5-15 mm diameter range. The influences of pellet size, bed temperature and superficial fluidization velocity on devolatilization time were evaluated. The variation of devolatilization time with particle diameter was expressed by the correlation, τ(d) = Ad(p)(N). The devolatilization time to pellet diameter curve shows nearly a linear increase in nitrogen, whereas an exponential increase in air. No noticeable effect of superficial fluidization velocity on devolatilization time in air atmosphere was observed. The behavior of the sludge pellets in the BFB was also focused during combustion experiments, primary fragmentation (a micro-explosive combustion phenomenon) was observed for bigger pellets (>10mm) at high bed temperatures (>700 °C), which occurred towards the end of combustion and remarkably reduce the devolatilization time of the oil sludge pellet. The size analysis of bed materials and fly ash showed that entire ash particle was entrained or elutriated out of the BFB furnace due to the fragile structure of oil sludge ash particles. Copyright © 2010 Elsevier B.V. All rights reserved.

28 CFR 570.21 - Time-frames.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Time-frames. 570.21 Section 570.21... PROGRAMS Pre-Release Community Confinement § 570.21 Time-frames. (a) Community confinement. Inmates may be... inmate's term of imprisonment or six months. (c) Exceeding time-frames. These time-frames may be exceeded...

28 CFR 570.21 - Time-frames.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 28 Judicial Administration 2 2013-07-01 2013-07-01 false Time-frames. 570.21 Section 570.21... PROGRAMS Pre-Release Community Confinement § 570.21 Time-frames. (a) Community confinement. Inmates may be... inmate's term of imprisonment or six months. (c) Exceeding time-frames. These time-frames may be exceeded...

28 CFR 570.21 - Time-frames.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 28 Judicial Administration 2 2014-07-01 2014-07-01 false Time-frames. 570.21 Section 570.21... PROGRAMS Pre-Release Community Confinement § 570.21 Time-frames. (a) Community confinement. Inmates may be... inmate's term of imprisonment or six months. (c) Exceeding time-frames. These time-frames may be exceeded...

28 CFR 570.21 - Time-frames.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 28 Judicial Administration 2 2012-07-01 2012-07-01 false Time-frames. 570.21 Section 570.21... PROGRAMS Pre-Release Community Confinement § 570.21 Time-frames. (a) Community confinement. Inmates may be... inmate's term of imprisonment or six months. (c) Exceeding time-frames. These time-frames may be exceeded...

28 CFR 570.21 - Time-frames.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 28 Judicial Administration 2 2011-07-01 2011-07-01 false Time-frames. 570.21 Section 570.21... PROGRAMS Pre-Release Community Confinement § 570.21 Time-frames. (a) Community confinement. Inmates may be... inmate's term of imprisonment or six months. (c) Exceeding time-frames. These time-frames may be exceeded...

Changes in kenaf properties and chemistry as a function of growing time

Treesearch

Roger M. Rowell; James S. Han

1999-01-01

Kenaf Tainung 1 cultivar was grown in Madison, WI in 1994. The ratio of core to bast fiber, total plant yield, protein, ash, fiber length, extractives, lignin, and sugar content were determined as a function of growing age. Ash, protein, extractives, L-arabinose, L-rhamnose, D-galactose, and D-mannose contents decreased while lignin, D-glucose and D-xylose content...

Effect of mixing geopolymer and peat on bearing capacity in Ogan Komering Ilir (OKI) by California bearing ratio (CBR) test

NASA Astrophysics Data System (ADS)

Raharja, Danang S.; Hadiwardoyo, Sigit P.; Rahayu, Wiwik; Zain, Nasuhi

2017-06-01

Geopolymer is binder material that consists of solid material and the activator solution. Geopolymer material has successfully replaced cement in the manufacture of concrete with aluminosilicate bonding system. Geopolymer concrete has properties similar to cement concrete with high compressive strength, low shrinkage value, relatively low creep value, as well as acid-resistant. Based on these, the addition of polymers in peat soils is expected to improve the bearing capacity of peat soils. A study on the influence of geopolymer addition in peat soils was done by comparing before and after the peat soil was mixed with geopolymer using CBR (California Bearing Ratio) test in unsoaked and soaked conditions. 10% mixture content of the peat dry was used, weighted with a variety of curing time 4 hours, 5 days, and 10 days. There were two methods of mixing: first, peat was mixed with fly ash geopolymer activators and mixed solution (waterglass, NaOH, water), and second, peat was mixed with fly ash and mixed geopolymer (waterglass, NaOH, water, fly ash). Changes were observed in specific gravity, dry density, acidity (pH), and the microscopic structure with Scanning Electron Microscope (SEM). Curing time did not significantly affect the CBR value. It even shows a tendency to decline with longer curing time. The first type mixture obtained CBR value of: 5.4% for 4 hours curing, 4.6% for 5 days curing and 3.6% for 10 days curing. The second type mixture obtained CBR value of: 6.1% for 4 hours curing, 5.2% for 5 days curing and 5.2% for 10 days curing. Furthermore, the specific gravity value, dry density, pH near neutral and swelling percentage increased. From both variants, the second type mixture shows better results than the first type mixture. The results of SEM (Scanning Electron Microscopy) show the structure of the peat which became denser with the fly ash particles filling the peat microporous. Also, the reaction of fly ash with geopolymer is indicated by the solid agglomerates that are larger than normal fly ash particle size.

Phreatomagmatic eruptive and depositional processes during the 1949 eruption on La Palma (Canary Islands)

NASA Astrophysics Data System (ADS)

White, James D. L.; Schmincke, Hans-Ulrich

1999-12-01

In 1949, a 5-week-long magmatic and phreatomagmatic eruption took place along the active volcanic ridge of La Palma (Canary Islands). Two vents, Duraznero and Hoyo Negro, produced significant pyroclastic deposits. The eruption began from Duraznero vent, which produced a series of deposits with an upward decrease in accidental fragments and increase in fluidal ash and spatter, together inferred to indicate decreasing phreatomagmatic interaction. Hoyo Negro erupted over a 2-week period, producing a variety of pyroclastic density currents and ballistic blocks and bombs. Hoyo Negro erupted within and modified an older crater having high walls on the northern to southeastern edges. Southwestern to western margins of the crater lay 50 to 100 m lower. Strongly contrasting deposits in the different sectors (N-SE vs. SW-W) were formed as a result of interaction between topography, weak eruptive columns and stratified pyroclastic density currents. Tephra ring deposits are thicker and coarser-grained than upper rim deposits formed along the higher edges of the crater, and beyond the crater margin, valley-confined deposits are thicker than more thinly bedded mantling deposits on higher topography. These differences indicate that the impact zone for the bulk of the collapsing, tephra-laden column lay within the crater and that the high crater walls inhibited escape of pyroclastic density currents to the north and east. The impact zone lay outside the low SW-W rims, however, thus allowing stratified pyroclastic density currents to move freely away from the crater in those directions, depositing thin sections (<30 cm) of well-bedded ash (mantling deposits) on ridges and thicker sections (1-3 m) of structureless ash beds in valleys and small basins. Such segregation of dense pyroclastic currents from more dilute ones at the crater wall is likely to be common for small eruptions from pre-existing craters and is an important factor to be taken into account in volcanic hazards assessments.

Volcanic ash and daily mortality in Sweden after the Icelandic volcano eruption of May 2011.

PubMed

Oudin, Anna; Carlsen, Hanne K; Forsberg, Bertil; Johansson, Christer

2013-12-10

In the aftermath of the Icelandic volcano Grimsvötn's eruption on 21 May 2011, volcanic ash reached Northern Europe. Elevated levels of ambient particles (PM) were registered in mid Sweden. The aim of the present study was to investigate if the Grimsvötn eruption had an effect on mortality in Sweden. Based on PM measurements at 16 sites across Sweden, data were classified into an ash exposed data set (Ash area) and an unexposed data set (No ash area). Data on daily all-cause mortality were obtained from Statistics Sweden for the time period 1 April through 31 July 2011. Mortality ratios were calculated as the ratio between the daily number of deaths in the Ash area and the No ash area. The exposure period was defined as the week following the days with elevated particle concentrations, namely 24 May through 31 May. The control period was defined as 1 April through 23 May and 1 June through 31 July. There was no absolute increase in mortality during the exposure period. However, during the exposure period the mean mortality ratio was 2.42 compared with 2.17 during the control period, implying a relatively higher number of deaths in the Ash area than in the No ash area. The differences in ratios were mostly due to a single day, 31 May, and were not statistically significant when tested with a Mann-Whitney non-parametric test (p > 0.3). The statistical power was low with only 8 days in the exposure period (24 May through 31 May). Assuming that the observed relative differences were not due to chance, the results would imply an increase of 128 deaths during the exposure period 24-31 May. If 31 May was excluded, the number of extra deaths was reduced to 20. The results of the present study are contradicting and inconclusive, but may indicate that all-cause mortality was increased by the ash-fall from the Grimsvötn eruption. Meta-analysis or pooled analysis of data from neighboring countries might make it possible to reach sufficient statistical power to study effects of the Grimsvötn ash on morbidity and mortality. Such studies would be of particular importance for European societies preparing for future large scale volcanic eruptions in Iceland.

Volcanic Ash and Daily Mortality in Sweden after the Icelandic Volcano Eruption of May 2011

PubMed Central

Oudin, Anna; Carlsen, Hanne K.; Forsberg, Bertil; Johansson, Christer

2013-01-01

In the aftermath of the Icelandic volcano Grimsvötn’s eruption on 21 May 2011, volcanic ash reached Northern Europe. Elevated levels of ambient particles (PM) were registered in mid Sweden. The aim of the present study was to investigate if the Grimsvötn eruption had an effect on mortality in Sweden. Based on PM measurements at 16 sites across Sweden, data were classified into an ash exposed data set (Ash area) and an unexposed data set (No ash area). Data on daily all-cause mortality were obtained from Statistics Sweden for the time period 1 April through 31 July 2011. Mortality ratios were calculated as the ratio between the daily number of deaths in the Ash area and the No ash area. The exposure period was defined as the week following the days with elevated particle concentrations, namely 24 May through 31 May. The control period was defined as 1 April through 23 May and 1 June through 31 July. There was no absolute increase in mortality during the exposure period. However, during the exposure period the mean mortality ratio was 2.42 compared with 2.17 during the control period, implying a relatively higher number of deaths in the Ash area than in the No ash area. The differences in ratios were mostly due to a single day, 31 May, and were not statistically significant when tested with a Mann-Whitney non-parametric test (p > 0.3). The statistical power was low with only 8 days in the exposure period (24 May through 31 May). Assuming that the observed relative differences were not due to chance, the results would imply an increase of 128 deaths during the exposure period 24–31 May. If 31 May was excluded, the number of extra deaths was reduced to 20. The results of the present study are contradicting and inconclusive, but may indicate that all-cause mortality was increased by the ash-fall from the Grimsvötn eruption. Meta-analysis or pooled analysis of data from neighboring countries might make it possible to reach sufficient statistical power to study effects of the Grimsvötn ash on morbidity and mortality. Such studies would be of particular importance for European societies preparing for future large scale volcanic eruptions in Iceland. PMID:24336019

Behavior of plastic sand confinement grids

DOT National Transportation Integrated Search

1986-01-01

The concept of improving the load carrying ability of unbound aggregates, particularly sand, by lateral confinement has been investigated for some time. Extensive full-scale testing of the trafficability of confined beach sand pavement layers has bee...

Experimental sintering of ash at conduit conditions and implications for the longevity of tuffisites

NASA Astrophysics Data System (ADS)

Gardner, James E.; Wadsworth, Fabian B.; Llewellin, Edward W.; Watkins, James M.; Coumans, Jason P.

2018-03-01

Escape of gas from magma in the conduit plays a crucial role in mitigating explosivity. Tuffisite veins—ash-filled cracks that form in and around volcanic conduits—represent important gas escape pathways. Sintering of the ash infill decreases its porosity, eventually forming dense glass that is impermeable to gas. We present an experimental investigation of surface tension-driven sintering and associated densification of rhyolitic ash under shallow conduit conditions. Suites of isothermal (700-800 °C) and isobaric H2O pressure (20 and 40 MPa) experiments were run for durations of 5-90 min. Obsidian powders with two different size distributions were used: 1-1600 μm (mean size = 89 μm), and 63-400 μm (mean size = 185 μm). All samples evolved similarly through four textural phases: phase 1—loose and cohesion-less particles; phase 2—particles sintered at contacts and surrounded by fully connected tortuous pore space of up to 40% porosity; phase 3—continuous matrix of partially coalesced particles that contain both isolated spherical vesicles and connected networks of larger, contorted vesicles; phase 4—dense glass with 2-5% fully isolated vesicles that are mainly spherical. Textures evolve faster at higher temperature and higher H2O pressure. Coarse samples sinter more slowly and contain fewer, larger vesicles when fully sintered. We quantify the sintering progress by measuring porosity as a function of experimental run-time, and find an excellent collapse of data when run-time is normalized by the sintering timescale {λ}_s=η \\overline{R}/σ , where η is melt viscosity, \\overline{R} is mean particle radius, and σ is melt-gas surface tension. Because timescales of diffusive H2O equilibration are generally fast compared to those of sintering, the relevant melt viscosity is calculated from the solubility H2O content at experimental temperature and pressure. We use our results to develop a framework for estimating ash sintering rates under shallow conduit conditions, and predict that sintering of ash to dense glass can seal tuffisites in minutes to hours, depending on pressure (i.e., depth), temperature, and ash size.

Photogrammetric Retrieval of Etna's Plume Height from SEVIRI and MODIS

NASA Astrophysics Data System (ADS)

Zaksek, K.; Ganci, G.; Hort, M. K.

2013-12-01

Even remote volcanoes can impact the modern society due to volcanic ash dispersion in the atmosphere. A lot of research is currently dedicated to minimizing the impact of volcanic ash on air traffic. But the ash transport in the atmosphere and its deposition on land and in the oceans may also significantly influence the climate through modifications of atmospheric CO2. The emphasis of this contribution is the retrieval of volcanic ash plume height. This is important information for air traffic, to predict ash transport and to estimate the mass flux of the ejected material. The best way to monitor volcanic ash cloud top height (ACTH) on the global level is using satellite remote sensing. The most commonly used method for satellite ACTH compares brightness temperature of the cloud with the atmospheric temperature profile. Because of well-known uncertainties of this method we propose photogrammetric methods based on the parallax between data retrieved from geostationary (SEVIRI, HRV band; 1000 m spatial resolution) and polar orbiting satellites (MODIS, band 1; 250 m spatial resolution). The procedure works well if the data from both satellites are retrieved nearly simultaneously butMODIS does not retrieve the data at exactly the same time as SEVIRI. To compensate for advection in the atmosphere we use two sequential SEVIRI images (one before and one after the MODIS retrieval) and interpolate the cloud position from SEVIRI data to the time of MODIS retrieval. ACTH is then estimated by intersection of corresponding lines-of-view from MODIS and interpolated SEVIRI data. The proposed method has already been tested for the case of the Eyjafjallajökull eruption in April 2010. This case study had almost perfect conditions as the plume was vast and stretching over a homogeneous background - ocean. Here we show results of ACTH estimation during lava fountaining activity of Mount Etna in years 2011-2013. This activity resulted in volcanic ash plumes that are much smaller than the plume observed at Eyjafjallajökull eruption. Challenges and problems occurring while applying the photogrammetric method to small and medium sized plumes will be discussed and solutions to those challenges will be shown.

The behavior of self-compacting concrete (SCC) with bagasse ash

NASA Astrophysics Data System (ADS)

Hanafiah, Saloma, Whardani, Putri Nurul Kusuma

2017-11-01

Self-Compacting Concrete (SCC) has the ability to flow and self-compacting. One of the benefit of SCC can reduced the construction time and labor cost. The materials to be used for see slightly different with the conventional concrete. Less coarse aggregate to be used up to 50%. The maximum size of coarse aggregate was also limited e.g. 10 mm. Other material was quartz sand with grain size of 50-650 µm. For reducing the around of cement, bagasse ash was used as partial replacement of cement. In this research, the variations of w/c to be used, e.g. 0.275, 0.300, 0.325 and the percentage of bagasse ash substitution were 10%, 15%, and 20%. EFNARC standard was conducted for slump flow test following the V-funnel test and L-box shape test. The maximum value of slump flow test was 75.75 cm, V-funnel test was 4.95 second, and L-box test was 1.000 yielded by mixture with w/c = 0.325 and 0% of bagasse ash. The minimum value of slump flow test was 61.50 cm, V-funnel test is 21.05 second, and L-box test was 0.743 yielded by mixture with w/c = 0.275 and 20% of bagasse ash. The maximum value of compressive strength was 67.239 MPa yielded by mixture with w/c = 0.275 and 15% of bagasse ash. And the minimum value of compressive strength was 41.813 MPa yielded by mixture with w/c = 0.325 and 20% bagasse ash.

Development of Soil Bacterial Communities in Volcanic Ash Microcosms in a Range of Climates.

PubMed

Kerfahi, Dorsaf; Tateno, Ryunosuke; Takahashi, Koichi; Cho, HyunJun; Kim, Hyoki; Adams, Jonathan M

2017-05-01

There is considerable interest in understanding the processes of microbial development in volcanic ash. We tested the predictions that there would be (1) a distinctive bacterial community associated with soil development on volcanic ash, including groups previously implicated in weathering studies; (2) a slower increase in bacterial abundance and soil C and N accumulation in cooler climates; and (3) a distinct communities developing on the same substrate in different climates. We set up an experiment, taking freshly fallen, sterilized volcanic ash from Sakurajima volcano, Japan. Pots of ash were positioned in multiple locations, with mean annual temperature (MAT) ranging from 18.6 to -3 °C. Within 12 months, bacteria were detectable by qPCR in all pots. By 24 months, bacterial copy numbers had increased by 10-100 times relative to a year before. C and N content approximately doubled between 12 and 24 months. HiSeq and MiSeq sequencing of the 16S rRNA gene revealed a distinctive bacterial community, different from developed vegetated soils in the same areas, for example in containing an abundance of unclassified bacterial groups. Community composition also differed between the ash pots at different sites, while showing no pattern in relation to MAT. Contrary to our predictions, the bacterial abundance did not show any relation to MAT. It also did not correlate to pH or N, and only C was statistically significant. It appears that bacterial community development on volcanic ash can be a rapid process not closely sensitive to temperature, involving distinct communities from developed soils.

Effect of kaolin addition on the performance of controlled low-strength material using industrial waste incineration bottom ash.

PubMed

Naganathan, Sivakumar; Razak, Hashim Abdul; Hamid, Siti Nadzriah Abdul

2010-09-01

Incineration of industrial waste produces large quantities of bottom ash which are normally sent to secured landfill, but is not a sustainable solution. Use of bottom ash in engineering applications will contribute to sustainability and generate revenue. One way of using the industrial waste incineration bottom ash is in controlled low-strength material (CLSM). Use of bottom ash in CLSM has problems related to bleeding and excessive strength development and so an additive has to be used to control bleeding and strength development. The main objective of this research is to study the effect of kaolin addition on the performance of CLSM made using industrial waste incineration bottom ash. CLSM mixes were made with bottom ash, cement, and refined kaolin. Various tests were performed on the CLSM in fresh and hardened states including compressive strength, water absorption, California bearing ratio (CBR) and the tests for concentration of leachable substances on the bleed and leachate. The compressive strength of CLSM tested ranged from 0.11 to 9.86 MPa. CBR values ranged from 6 to 46, and water absorption values from 12 to 36%. It was shown that the addition of kaolin delayed the initial setting time of CLSM mixtures, reduced bleeding, lowered the compressive strength, and increased the values of water absorption, sorption, and initial surface absorption. The CLSM tested did not have corrosivity. It was shown that the hardened CLSM was non hazardous, and the addition of kaolin increased the concentration of heavy metals and salts in the bleed and leachate.

Potassic zeolites from Brazilian coal ash for use as a fertilizer in agriculture.

PubMed

Flores, Camila Gomes; Schneider, Helena; Marcilio, Nilson Romeu; Ferret, Lizete; Oliveira, João Carlos Pinto

2017-12-01

Brazilian coal has an ash content ranging from 30 to 50% by weight. Consequently, its use in coal-fired thermoelectric for power production generates a lot of waste. The construction sector is the largest consumer of coal ash, but it cannot absorb the entire amount generated. Thus, other applications for coal ash should be studied in aim to optimize the use of this industrial waste. This research had as focus to synthesize potassic zeolite from of the coal ash into on potassium fertilizer for the grown wheat plant. In this work, it was used a subbituminous coal from Mina do Leão (RS, Brazil) presenting 48.7% ash content on a dry basis. Concerning the synthesis of potassic zeolite, it was adopted the conventional method of hydrothermal treatment with potassium hydroxide. A schedule of experiments was conducted in order to define the optimum condition of zeolite synthesis that was then used an alkaline solution of 5M KOH with a reaction time of 24h at 150°C. According to this procedure, it was obtained a zeolite with a single crystalline phase, identified through X-ray diffraction as Merlinoite. Subsequently, it was performed a set of tests using potassic zeolite asa fertilizer for plants in a greenhouse. The synthesized potassic zeolite showed a good potential for its use as fertilizer in agriculture. Copyright © 2017 Elsevier Ltd. All rights reserved.

Lauryl Amine as heavy metal collector of boiler ash from pulp and paper mill waste

NASA Astrophysics Data System (ADS)

Sembiring, M. P.; Kaban, J.; Bangun, N.; Saputra, E.

2018-04-01

Theincreasing of demand of pulp and paper products, will following with the growing the pulp and paper industryand generate significant mill waste. The total waste reached 1/3 of the amount raw materials used and ash boiler is the waste with the largest percentage of 52%. For that it takes effort to manage the existing waste. The boiler ash contained the chemical elements, it can be utilized such as fertilizer, because it also contains transition metals in form of heavy metal such as Cadmium (Cd), Cobalt (Co), Chrome (Cr), Cupprum (Cu), Ferrum (Fe), Nickel (Ni), and Zinc (Zn), the use of boiler ash must follow the threshold specified by the Government. Several studies have been undertaken to reduce and extract heavy metals from ash and sand of the boiler by using carbon dioxide as its ligand. Eelectrochemical method was used to remove and recovery of heavy metals from the incenerator. This study focused on removal of heavy metals using Lauryl Amine as collector and three solvents namely Dichloromethane, Ethanol and n-Hexane. The treatmentswas able to extract the heavy metal and generally reduce the heavy metal content of ash boiler pulp and paper mill waste. The combination treatment used toreduce the heavy metal content of 5 gram Lauryl Amine collector in Dichloromethane solvent for 4 hours process time.

Growth response, nutrient and mineral retention, bone mineralisation and walking ability of broiler chickens fed with dietary inclusion of various unconventional mineral sources.

PubMed

Oso, A O; Idowu, A A; Niameh, O T

2011-08-01

Growth response, nutrient and mineral retention, bone mineral content and walking ability of broiler chicken fed dietary inclusion of various unconventional calcium sources were studied using 160-day-old broilers. Four isonitrogenous, isocaloric diets balanced for Ca and P were formulated such that oyster shell, snail shell, wood ash and limestone were used as main non-phytate (Ca from other sources apart from plant) calcium sources. Each dietary treatment consisted of 40 birds replicated four times with 10 birds per replicate. A single diet was fed to the broilers throughout the duration of the study which lasted for 8 weeks. Broilers fed diet containing oyster shell as calcium sources recorded the highest (p < 0.05) feed intake of 5863.30 g, while those fed diet containing limestone consumed the least intake (p < 0.05) of 5432.56 g. Occurrence of lameness and evidences of gaits were highest (p < 0.05) for broilers fed diet containing wood ash. Lowest (p < 0.05) Ca and ash retention were recorded for broiler fed diet containing wood ash as Ca sources. Similar tibia ash values were recorded for broilers fed oyster shell, snail shell and limestone. Wood ash inclusion resulted in a low Ca availability hence its inclusion in feeds for broilers should be discouraged. © 2011 Blackwell Verlag GmbH.

Effect of municipal solid waste incinerator types on characteristics of ashes from different air pollution control devices.

PubMed

Lu, Chien-Hsing; Chuang, Kui-Hao

2016-01-01

The purpose of this paper is to investigate the characteristics of fly and bottom ashes sampled from both fluidized bed (FB) and mass-burning (MB) municipal solid waste incinerators (MSWIs), respectively. Fly ashes from different locations at FB and MB MSWIs equipped with a cyclone, a semi-dry scrubber, and a bag filter as air pollution control devices were examined to provide the baseline information between physicochemical properties and leaching ability. Experimental results of leachability indicated that the bag filter fly ash (FB-FA(B)) from the FB incinerator meets Taiwan regulatory standards set through the toxicity characteristic leaching procedure. X-ray diffraction results revealed the presence of Cr5O12 and Pb2O3 in the cyclone fly ash (MB-FA(C)) and bag filter fly ash (MB-FA(B)), respectively, from the MB incinerator. To observe lead incorporation mechanism, mixture of simulate lead-laden waste with bed material were fired between 600 °C and 900 °C in a laboratory scale FB reactor. The results clearly demonstrate a substantial decrease in lead leaching ratio for products with an appropriate temperature. The concentration of Pb in the MB-FA(B) was 250 times that in the FB-FA(B), suggesting that incineration of MSW in FB is a good strategy for stabilizing hazardous metals.

Alkaline bioleaching of municipal solid waste incineration fly ash by autochthonous extremophiles.

PubMed

Ramanathan, Thulasya; Ting, Yen-Peng

2016-10-01

The increasing demand for energy and the generation of solid waste have caused an alarming rise in fly ash production globally. Since heavy metals continue to be in demand for the production of materials, resource recovery from the recycling of these wastes has the potential to delay the depletion of natural ores. The use of microorganisms for the leaching of metals, in a process called bioleaching, is an eco-friendly and economical way to treat the metal-laden wastes. Bioleaching of fly ash is challenging due largely to the alkaline nature and toxic levels of heavy metals which are detrimental to microbial growth and bioleaching activity. The present work reports the isolation of indigenous bacteria from a local landfill site and their bioleaching performance [corrected]. 38 autochthonous strains of bacteria were isolated from eight samples collected and plated on five different media. 18 of the isolates showed bioleaching potential, with significant alkaline pH or fly ash tolerance. Genetic characterization of the strains revealed a dominance of Firmicutes, with Alkalibacterium sp. TRTYP6 showing highest fly ash tolerance of up to 20% w/v fly ash, and growth over a pH range 8-12.5. The organism selectively recovered about 52% Cu from the waste. To the best of our knowledge, this is the first time a study on bioleaching with extreme alkaliphiles is reported. Copyright © 2016 Elsevier Ltd. All rights reserved.

Geochemical anomalies from bottom ash in a road construction--comparison of the leaching potential between an ash road and the surroundings.

PubMed

Lind, Bo B; Norrman, Jenny; Larsson, Lennart B; Ohlsson, Sten-Ake; Bristav, Henrik

2008-01-01

A study was performed between June 2001 and December 2004 with the primary objective of assessing long-term leaching from municipal solid waste incineration bottom ash in a test road construction in relation to a reference road made up of conventional materials and the natural geochemical conditions in the surroundings. The metal leaching from the test road and the reference road was compared with the natural weathering in the regional surroundings for three time scales: 16, 80 and 1000 years. The results show that Cu and Zn cause a geochemical anomaly from the test road compared with the surroundings. The leaching of Cu from the test road is initially high but will decline with time and will in the long term be exceeded by natural weathering. Zn on the other hand has low initial leaching, which will increase with time and will in the long term exceed that of the test road and the surroundings by a factor of 100-300. For the other metals studied, Al, Na, K and Mg, there is only very limited leaching over time and the potential accumulation will not exceed the background values in a 1000 years.

Vortex Ring Dynamics in Radially Confined Domains

NASA Astrophysics Data System (ADS)

Stewart, Kelley; Niebel, Casandra; Jung, Sunghwan; Vlachos, Pavlos

2010-11-01

Vortex ring dynamics have been studied extensively in semi-infinite quiescent volumes. However, very little is known about vortex-ring formation in wall-bounded domains where vortex wall interaction will affect both the vortex ring pinch-off and propagation velocity. This study addresses this limitation and studies vortex formation in radially confined domains to analyze the affect of vortex-ring wall interaction on the formation and propagation of the vortex ring. Vortex rings were produced using a pneumatically driven piston cylinder arrangement and were ejected into a long cylindrical tube which defined the confined downstream domain. A range of confinement domains were studied with varying confinement diameters Velocity field measurements were performed using planar Time Resolved Digital Particle Image Velocimetry (TRDPIV) and were processed using an in-house developed cross-correlation PIV algorithm. The experimental analysis was used to facilitate the development of a theoretical model to predict the variations in vortex ring circulation over time within confined domains.

Measurement of Trace Metals in Tobacco and Cigarette Ash by Inductively Coupled Plasma-Atomic Emission Spectroscopy

NASA Astrophysics Data System (ADS)

Wang, W.; Finlayson-Pitts, B. J.

2003-01-01

The ICP AES experiment reported here is suitable for use in a junior- or senior-level undergraduate instrumental analysis laboratory. The objective of this experiment is to analyze trace metals present in cigarette tobacco, the cigarette filter, and the ash obtained when the cigarette is burned. Two different brands of cigarettes, one with and one without a filter, were used. The filter was analyzed before and after smoke was drawn through it. The trace metals were extracted using concentrated nitric acid at room temperature and at 100 °C respectively, to test the extraction efficiency. Some tobacco samples were spiked with ZnCl2 and FeCl3 to assess the efficiency of the recovery. Zinc and iron are shown to be present in tobacco, filter, and ash, while chromium was above the detection limit only in the ash. These metals are concentrated in the ash compared to the tobacco by factors of ˜4 (Zn), 12 17 (Fe), and ≥ 2 (Cr). If sufficient laboratory time is available, this experiment could be paired with one using atomic absorption (AA) to demonstrate the advantages and disadvantages of ICP when compared to AA.

Volcanic Ash Cloud Altitude retrievals from passive satellite sensors: the 03-09 December 2015 Etna eruption.

NASA Astrophysics Data System (ADS)

corradini, stefano; merucci, luca; guerrieri, lorenzo; pugnaghi, sergio; mcgarragh, greg; carboni, elisa; ventress, lucy; grainger, roy; scollo, simona; pardini, federica; zaksek, klemen; langmann, baerbel; bancalá, severin; stelitano, dario

2016-04-01

The volcanic ash cloud altitude is one of the most important parameter needed for the volcanic ash cloud estimations (mass, effective radius and optical depth). It is essential by modelers to initialize the ash cloud transportation models, and by volcanologists to give insights into eruption dynamics. Moreover, it is extremely important in order to reduce the disruption to flights as a result of volcanic activity whilst still ensuring safe travel. In this work, the volcanic ash cloud altitude is computed from remote sensing passive satellite data (SEVIRI, MODIS, IASI and MISR) by using the most of the existing retrieval techniques. A novel approach, based on the CO2 slicing procedure, is also shown. The comparisons among different techniques are presented and advantages and drawbacks emphasized. As test cases Etna eruptions in the period between 03 and 09 December 2015 are considered. During this time four lava fountain events occurred at the Voragine crater, forming eruption columns higher than 12 km asl and producing copious tephra fallout on volcano flanks. These events, among the biggest of the last 20 years, produced emissions that reached the stratosphere and produced a circum-global transport throughout the northern hemisphere.

Use of bottom ash from olive pomace combustion in the production of eco-friendly fired clay bricks.

PubMed

Eliche-Quesada, D; Leite-Costa, J

2016-02-01

Olive pomace bottom ash was used to replace different amounts (10-50wt%) of clay in brick manufacturing. The aim of this study is both studying bricks properties and showing a new way of olive pomace bottom ash recycling. Properties of waste bricks were compared to conventional products following standard procedures in order to determine the maximum waste percentage. The amount of olive pomace bottom ash is limited to 20wt%, obtaining bricks with superior engineering properties when 10wt% of waste is added. Adding higher amount of waste (30-50wt%) resulted in bricks with water absorption and compressive strength values on the edge of meeting those established by standards. Therefore, the addition of 10 and 20wt% of olive pomace bottom ash produced bricks with a bulk density of 1635 and 1527kg/m(3) and a compressive strength of 33.9MPa and 14.2MPa, respectively. Fired bricks fulfil standards requirements for clay masonry units, offering, at the same time, better thermal insulation of buildings due to a reduction in thermal conductivity of 14.4% and 16.8% respectively, compared to control bricks (only clay). Copyright © 2015 Elsevier Ltd. All rights reserved.

Speciation analysis of antimony in extracts of size-classified volcanic ash by HPLC-ICP-MS.

PubMed

Miravet, R; López-Sánchez, J F; Rubio, R; Smichowski, P; Polla, G

2007-03-01

Although there is concern about the presence of toxic elements and their species in environmental matrices, for example water, sediment, and soil, speciation analysis of volcanic ash has received little attention. Antimony, in particular, an emerging element of environmental concern, has been less studied than other potentially toxic trace elements. In this context, a study was undertaken to assess the presence of inorganic Sb species in ash emitted from the Copahue volcano (Argentina). Antimony species were extracted from size-classified volcanic ash (<36 microm, 35-45 microm, 45-150 microm, and 150-300 microm) by use of 1 mol L(-1) citrate buffer at pH 5. Antimony(III) and (V) in the extracts were separated and quantified by high-performance liquid chromatography combined on-line with inductively coupled plasma mass spectrometry (HPLC-ICP-MS). Antimony species concentrations (microg g(-1)) in the four fractions varied from 0.14 to 0.67 for Sb(III) and from 0.02 to 0.03 for Sb(V). The results reveal, for the first time, the occurrence of both inorganic Sb species in the extractable portion of volcanic ash. Sb(III) was always the predominant species.

Influence of heating on the weight loss and mineral phase in MSWI ash: LOI of incineration ash

NASA Astrophysics Data System (ADS)

Yang, Shuo

2017-04-01

Loss on ignition (LOI) is a very common method for estimating the volatile species in solid sample. Normally, the measurement of LOI can be convenient and accurate, but for municipal solid waste incineration (MSWI) ash, the process may become intricate due to the complexity of the sample. In the incineration ash, there exist various phases, such as mineral, metal, organic and glass. The reaction and transformation of some materials during heating will influence the measurement. 5 incineration ash samples were selected and tested in this study. LOI content was basically measured at high (850°C) and relatively low (440°C) temperatures. The comparison between these two measurements showed a large difference. X-ray diffraction (XRD) and thermal analysis (TG-DTA) were carried out to investigate the mineral changes and weight losses with different ignition temperatures. The mineralogical analysis suggests that the decomposition of hydrate and carbonate phases cannot be neglected for LOI measurement of incineration. A long-time heating under relatively lower temperature (400∼450°C) compared with soil sample measurement (≥500°C) was recommended by this study.

Engineering properties of cement mortar with pond ash in South Korea as construction materials: from waste to concrete

NASA Astrophysics Data System (ADS)

Jung, Sang Hwa; Kwon, Seung-Jun

2013-09-01

Among the wastes from coal combustion product, only fly ash is widely used for mineral mixture in concrete for its various advantages. However the other wastes including bottom ash, so called PA (pond ash) are limitedly reused for reclamation. In this paper, the engineering properties of domestic pond ash which has been used for reclamation are experimentally studied. For this, two reclamation sites (DH and TA) in South Korea are selected, and two domestic PAs are obtained. Cement mortar with two different w/c (water to cement) ratios and 3 different replacement ratios (0%, 30%, and 60%) of sand are prepared for the tests. For workability and physical properties of PA cement mortar, several tests like flow, setting time, and compressive strength are evaluated. Several durability tests including porosity measuring, freezing and thawing, chloride migration, and accelerated carbonation are also performed. Through the tests, PA (especially from DH area) in surface saturated condition is evaluated to have internal curing action which leads to reasonable strength development and durability performances. The results show a potential applicability of PA to concrete aggregate, which can reduce consuming natural resources and lead to active reutilization of coal product waste.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jan D. Miller; Terrence Chatwin; Jan Hupka

The two-year Department of Energy (DOE) project ''Treatment of Cyanide Solutions and Slurries Using Air-Sparged Hydrocyclone (ASH) Technology'' (ASH/CN) has been completed. This project was also sponsored by industrial partners, ZPM Inc., Elbow Creek Engineering, Solvay Minerals, EIMCO-Baker Process, Newmont Mining Corporation, Cherokee Chemical Co., Placer Dome Inc., Earthworks Technology, Dawson Laboratories and Kennecott Minerals. Development of a new technology using the air-sparged hydrocyclone (ASH) as a reactor for either cyanide recovery or destruction was the research objective. It was expected that the ASH could potentially replace the conventional stripping tower presently used for HCN stripping and absorption with reducedmore » power costs. The project was carried out in two phases. The first phase included calculation of basic processing parameters for ASH technology, development of the flowsheet, and design/adaptation of the ASH mobile system for hydrogen cyanide (HCN) recovery from cyanide solutions. This was necessary because the ASH was previously used for volatile organics removal from contaminated water. The design and modification of the ASH were performed with the help from ZPM Inc. personnel. Among the modifications, the system was adapted for operation under negative pressure to assure safe operating conditions. The research staff was trained in the safe use of cyanide and in hazardous material regulations. Cyanide chemistry was reviewed resulting in identification of proper chemical dosages for cyanide destruction, after completion of each pilot plant run. The second phase of the research consisted of three field tests that were performed at the Newmont Mining Corporation gold cyanidation plant near Midas, Nevada. The first field test was run between July 26 and August 2, 2002, and the objective was to demonstrate continuous operation of the modified ASH mobile system. ASH units were applied for both stripping and absorption, to recover cyanide, using the acidification-volatilization-reabsorption chemistry. Plant barren cyanide solution was used during the field tests. The original ASH system used for the field tests had been designed and fabricated by ZPM Inc. to remove volatile organic compounds from ground water. The system, even with a number of modifications, could not operate at optimum conditions for cyanide recovery. Reactors and pumps installed in the mobile system only allowed for the treatment of clear solutions, not slurries. Also the original mobile system was limited with respect to Q, the relative air flow rate, and the extent of recovery in a single stage. Due to the lack of automatic controls, the system required constant supervision of the University of Utah (U/U) team. In spite of these difficulties, application of the ASH mobile system was particularly attractive due to compactness of the apparatus and less than 1 second residence time of the aqueous phase in the cyclones. The performance of the ASH system was evaluated by comparison with theoretical predictions.« less

Effects of a vertical magnetic field on particle confinement in a magnetized plasma torus.

PubMed

Müller, S H; Fasoli, A; Labit, B; McGrath, M; Podestà, M; Poli, F M

2004-10-15

The particle confinement in a magnetized plasma torus with superimposed vertical magnetic field is modeled and measured experimentally. The formation of an equilibrium characterized by a parallel plasma current canceling out the grad B and curvature drifts is described using a two-fluid model. Characteristic response frequencies and relaxation rates are calculated. The predictions for the particle confinement time as a function of the vertical magnetic field are verified in a systematic experimental study on the TORPEX device, including the existence of an optimal vertical field and the anticorrelation between confinement time and density.

The ash in forest fire affected soils control the soil losses. Part 1. The pioneer research

NASA Astrophysics Data System (ADS)

Cerdà, Artemi; Pereira, Paulo

2013-04-01

After forest fires, the ash and the remaining vegetation cover on the soil surface are the main protection against erosion agents. The control ash exert on runoff generation mechanism was researched during the 90's (Cerdà, 1998a; 1998b). This pioneer research demonstrated that after forest fires there is a short period of time that runoff and surface wash by water is controlled by the high infiltration rates achieved by the soil, which were high due to the effect of ash acting as a mulch. The research of Cerdà (1998a; 1998b) also contributed to demonstrate that runoff was enhanced four month later upon the wash of the ash by the runoff, but also due to the removal of ash due to dissolution and water infiltration. As a consequence of the ephemeral ash cover the runoff and erosion reached the peak after the removal of the ash (usually four month), and for two years the soil erosion reached the peak (Cerdà, 1998a). Research developed during the last decade shown that the ash and the litter cover together contribute to reduce the soil losses after the forest fire (Cerdà and Doerr, 2008). The fate of the ash is related to the climatic conditions of the post-fire season, as intense thunderstorms erode the ash layer and low intensity rainfall contribute to a higher infiltration rate and the recovery of the vegetation. Another, key factor found during the last two decades that determine the fate of the ash and the soil and water losses is the impact of the fauna (Cerdà and Doerr, 2010). During the last decade new techniques were developed to study the impact of ash in the soil system, such as the one to monitor the ash changes by means of high spatial resolution photography (Pérez Cabello et al., 2012), and laboratory approaches that show the impact of ash as a key factor in the soil hydrology throughout the control they exert on the soil water repellency (Bodí et al., 2012). Laboratory approaches also shown that the fire severity is a key factor on the ash chemical composition (Pereira and Úbeda, 2010) and Pereira et al., 2012). Some of the new research challenges related to ash impact in the fire affected soils are related to the ash redistribution after the fire, the impact of ash in soil and water chemistry, the temporal changes of soil erosion, the control ash exert on vegetation recovery and the role to be played by ash in the best management of fire affected land. Those topics needs new ideas and new scientists such as Paulo Pereira show in the Part II of this abstract. Acknowledgements, Lithuanian Research Council. Project LITFIRE, Fire effects on Lithuanian soils and ecosystems (MIP-48/2011) and the research projects GL2008-02879/BTE and LEDDRA 243857. References Bodí, M., Mataix-Solera, J., Doerr, S., and Cerdà, A. 2011b. The wettability of ash from burned vegetation and its relationship to Mediterranean plant species type, burn severity and total organic carbon content. Geoderma, 160, 599-607. Cerdà, A. 1998a. Postfire dynamics of erosional processes under mediterranean climatic conditions. Z. Geomorphol., 42 (3) 373-398. Cerdà, A. 1998b. Changes in overland flow and infiltration after a rangeland fire in a Mediterranean scrubland. Hydrological Processes, 12, 1031-1042. Cerdà, A., and Doerr, S. H.2010. The effect of ant mounds on overland flow and soil erodibility following a wildfire in eastern Spain. Ecohydrology, 3, 392-401. Cerdà, A., and Doerr, S.H. 2008. The effect of ash and needle cover on surface runoff and erosion in the immediate post-fire period. Catena, 74, 256-263. Pereira, P., and Úbeda, X. 2010. Spatial distribution of heavy metals released from ashes after a wildfire, Journal of Environment Engineering and Landscape Management, 18, 13-22. Pereira, P., Ubeda, X., Martin, D.A. 2012. Fire severity effects on ash chemical composition and extractable elements. Geoderma, 191, 105 - 114. Pérez-Cabello, F., Cerdà, A., de la Riva, J., Echeverría, M.T., García-Martín, A., Ibarra, P., Lasanta, T., Montorio, R., Palacios, V. 2012. Micro-scale post-fire surface cover changes monitored using high spatial resolution photography in a semiarid environment: A useful tool in the study of post-fire soil erosion processes. Journal of Arid Environments, 76, 88-96.

New U-Pb zircon ages and the duration and division of Devonian time

USGS Publications Warehouse

Tucker, R.D.; Bradley, D.C.; Ver Straeten, C.A.; Harris, A.G.; Ebert, J.R.; McCutcheon, S.R.

1998-01-01

Newly determined U-Pb zircon ages of volcanic ashes closely tied to biostratigraphic zones are used to revise the Devonian time-scale. They are: 1) 417.6 ?? 1.0 Ma for an ash within the conodont zone of Icriodus woschmidti/I. w. hesperius Lochkovian); 2) 408.3 ?? 1.9 Ma for an ash of early Emsian age correlated with the conodont zones of Po. dehiscens--Lower Po. inversus; 3) 391.4 ?? 1.8 Ma for an ash within the Po. c. costatus Zone and probably within the upper half of the zone (Eifelian); and 4) 381.1 ?? 1.3 Ma for an ash within the range of the Frasnian conodont Palmatolepis punctata (Pa. punctata Zone to Upper Pa. hassi Zone). U-Pb zircon ages for two rhyolites bracketing a palyniferous bed of the pusillites-lepidophyta spore zone, are dated at 363.8 ?? 2.2 Ma and 363 ?? 2.2 Ma and 363.4 ?? 1.8 Ma, respectively, suggesting an age of ~363 Ma for a level within the late Famennian Pa. g. expansa Zone. These data, together with other published zircon ages, suggest that the base and top of the Devonian lie close to 418 Ma and 362 Ma, respectively, thus lengthening the period of ~20% over current estimates. We suggest that the duration of the Middle Devonian (Eifelian and Givitian) is rather brief, perhaps no longer than 11.5 Myr (394 Ma-382.5 Ma), and that the Emsian and Famennian are the longest stages in the period with estimated durations of ~15.5 Myr and 14.5 Myr, respectively.

Unsaturated flow processes in structurally-variable pathways in wildfire-affected soils and ash

NASA Astrophysics Data System (ADS)

Ebel, B. A.

2016-12-01

Prediction of flash flood and debris flow generation in wildfire-affected soils and ash hinges on understanding unsaturated flow processes. Water resources issues, such as groundwater recharge, also rely on our ability to quantify subsurface flow. Soil-hydraulic property data provide insight into unsaturated flow processes and timescales. A literature review and synthesis of existing data from the literature for wildfire-affected soils, including ash and unburned soils, facilitated calculating metrics and timescales of hydrologic response related to infiltration and surface runoff generation. Sorptivity (S) and the Green-Ampt wetting front parameter (Ψf) were significantly lower in burned soils compared to unburned soils, while field-saturated hydraulic conductivity (Kfs) was not significantly different. The magnitude and duration of the influence of capillarity was substantially reduced in burned soils, leading to faster ponding times in response to rainfall. Ash had large values of S and Kfs compared to unburned and burned soils but intermediate values of Ψf, suggesting that ash has long ponding times in response to rainfall. The ratio of S2/Kfs was nearly constant ( 100 mm) for unburned soils, but was more variable in burned soils. Post-wildfire changes in this ratio suggested that unburned soils had a balance between gravity and capillarity contributions to infiltration, which may depend on soil organic matter, while burning shifted infiltration more towards gravity contributions by reducing S. Taken together, the changes in post-wildfire soil-hydraulic properties increased the propensity for surface runoff generation and may have enhanced subsurface preferential flow through pathways altered by wildfire.

Development of an automatic volcanic ash sampling apparatus for active volcanoes

NASA Astrophysics Data System (ADS)

Shimano, Taketo; Nishimura, Takeshi; Chiga, Nobuyuki; Shibasaki, Yoshinobu; Iguchi, Masato; Miki, Daisuke; Yokoo, Akihiko

2013-12-01

We develop an automatic system for the sampling of ash fall particles, to be used for continuous monitoring of magma ascent and eruptive dynamics at active volcanoes. The system consists of a sampling apparatus and cameras to monitor surface phenomena during eruptions. The Sampling Apparatus for Time Series Unmanned Monitoring of Ash (SATSUMA-I and SATSUMA-II) is less than 10 kg in weight and works automatically for more than a month with a 10-kg lead battery to obtain a total of 30 to 36 samples in one cycle of operation. The time range covered in one cycle varies from less than an hour to several months, depending on the aims of observation, allowing researchers to target minute-scale fluctuations in a single eruptive event, as well as daily to weekly trends in persistent volcanic activity. The latest version, SATSUMA-II, also enables control of sampling parameters remotely by e-mail commands. Durability of the apparatus is high: our prototypes worked for several months, in rainy and typhoon seasons, at windy and humid locations, and under strong sunlight. We have been successful in collecting ash samples emitted from Showa crater almost everyday for more than 4 years (2008-2012) at Sakurajima volcano in southwest Japan.

Tracking composite material damage evolution using Bayesian filtering and flash thermography data

NASA Astrophysics Data System (ADS)

Gregory, Elizabeth D.; Holland, Steve D.

2016-05-01

We propose a method for tracking the condition of a composite part using Bayesian filtering of ash thermography data over the lifetime of the part. In this demonstration, composite panels were fabricated; impacted to induce subsurface delaminations; and loaded in compression over multiple time steps, causing the delaminations to grow in size. Flash thermography data was collected between each damage event to serve as a time history of the part. The ash thermography indicated some areas of damage but provided little additional information as to the exact nature or depth of the damage. Computed tomography (CT) data was also collected after each damage event and provided a high resolution volume model of damage that acted as truth. After each cycle, the condition estimate, from the ash thermography data and the Bayesian filter, was compared to 'ground truth'. The Bayesian process builds on the lifetime history of ash thermography scans and can give better estimates of material condition as compared to the most recent scan alone, which is common practice in the aerospace industry. Bayesian inference provides probabilistic estimates of damage condition that are updated as each new set of data becomes available. The method was tested on simulated data and then on an experimental data set.

Recent developments in the analysis of toxic elements.

PubMed

Lisk, D J

1974-06-14

One may conclude that it is impractical to confine oneself to any one analytical method since ever more sensitive instrumentation continues to be produced. However, in certain methods such as anodic stripping voltammetry and flameless atomic absorption it may be background contamination from reagent impurities and surroundings rather than instrument sensitivity which controls the limits of element detection. The problem of contamination from dust or glassware is greatly magnified when the sample size becomes ever smaller. Air entering laboratories near highways may contain trace quantities of lead, cadmium, barium, antimony, and other elements from engine exhaust. Even plastic materials contacting the sample may be suspect as a source of contamination since specific metals may be used as catalysts in the synthesis of the plastic and traces may be retained in it. Certain elements may even be deliberately added to plastics during manufacture for identification purposes. Nondestructive methods such as neutron activation and x-ray techniques thus offer great advantages not only in time but in the elimination of impurities introduced during sample ashing. Future improvements in attainable limits of detection may arise largely from progress in the ultrapurification of reagents and "clean-room" techniques. Finally, the competence of the analyst is also vitally important in the skillful operation of modern complex analytical instrumentation and in the experienced evaluation of data.

Confinement time of electron plasma approaching magnetic pumping transport limit in small aspect ratio C-shaped torus

NASA Astrophysics Data System (ADS)

Lachhvani, Lavkesh; Pahari, Sambaran; Goswami, Rajiv; Bajpai, Manu; Yeole, Yogesh; Chattopadhyay, P. K.

2016-06-01

A long confinement time of electron plasma, approaching magnetic pumping transport limit, has been observed in SMARTEX-C (a small aspect ratio partial torus with R o / a ˜ 1.59 ). Investigations of the growth rate reveal that they are governed by instabilities like resistive wall destabilization, ion driven instabilities, and electron-neutral collisions. Successful confinement of electron plasmas exceeding > 1 × 10 5 poloidal E → × B → rotations lasting for nearly 2.1 ± 0.1 s is achieved by suppressing these instabilities. The confinement time has been estimated in two ways: (a) from the frequency scaling of the linear diocotron mode launched from sections of the wall that are also used as capacitive probes and (b) by dumping the plasma onto a charge collector at different hold times.

MODIS volcanic ash retrievals vs FALL3D transport model: a quantitative comparison

NASA Astrophysics Data System (ADS)

Corradini, S.; Merucci, L.; Folch, A.

2010-12-01

Satellite retrievals and transport models represents the key tools to monitor the volcanic clouds evolution. Because of the harming effects of fine ash particles on aircrafts, the real-time tracking and forecasting of volcanic clouds is key for aviation safety. Together with the security reasons also the economical consequences of a disruption of airports must be taken into account. The airport closures due to the recent Icelandic Eyjafjöll eruption caused millions of passengers to be stranded not only in Europe, but across the world. IATA (the International Air Transport Association) estimates that the worldwide airline industry has lost a total of about 2.5 billion of Euro during the disruption. Both security and economical issues require reliable and robust ash cloud retrievals and trajectory forecasting. The intercomparison between remote sensing and modeling is required to assure precise and reliable volcanic ash products. In this work we perform a quantitative comparison between Moderate Resolution Imaging Spectroradiometer (MODIS) retrievals of volcanic ash cloud mass and Aerosol Optical Depth (AOD) with the FALL3D ash dispersal model. MODIS, aboard the NASA-Terra and NASA-Aqua polar satellites, is a multispectral instrument with 36 spectral bands operating in the VIS-TIR spectral range and spatial resolution varying between 250 and 1000 m at nadir. The MODIS channels centered around 11 and 12 micron have been used for the ash retrievals through the Brightness Temperature Difference algorithm and MODTRAN simulations. FALL3D is a 3-D time-dependent Eulerian model for the transport and deposition of volcanic particles that outputs, among other variables, cloud column mass and AOD. Three MODIS images collected the October 28, 29 and 30 on Mt. Etna volcano during the 2002 eruption have been considered as test cases. The results show a general good agreement between the retrieved and the modeled volcanic clouds in the first 300 km from the vents. Even if the modeled volcanic cloud area is systematically wider than the retrieved area, the ash total mass is comparable and varies between 35 and 60 kt and between 20 and 42 kt for FALL3D and MODIS respectively. The mean AOD values are in good agreement and approximately equal to 0.8. When the whole volcanic clouds are considered the ash areas and the total ash masses, computed by FALL3D model are significantly greater than the same parameters retrieved from the MODIS data, while the mean AOD values remain in a very good agreement and equal to about 0.6. The volcanic cloud direction in its distal part is not coincident for the 29 and 30 October 2002 images due to the difference between the real and the modeled local wind fields. Finally the MODIS maps show regions of high mass and AOD due to volcanic puffs not modeled by FALL3D.

Occurrence of emerald ash borer (Coleoptera: Buprestidae) and biotic factors affecting its immature stages in the Russian Far East.

PubMed

Duan, Jian J; Yurchenko, Galina; Fuester, Roger

2012-04-01

Field surveys were conducted from 2008 to 2011 in the Khabarovsk and Vladivostok regions of Russia to investigate the occurrence of emerald ash borer, Agrilus planipennis Fairmaire, and mortality factors affecting its immature stages. We found emerald ash borer infesting both introduced North American green ash (Fraxinus pennsylvanica Marshall) and native oriental ashes (F. mandshurica Rupr. and F. rhynchophylla Hance) in both regions. Emerald ash borer densities (larvae/m(2) of phloem area) were markedly higher on green ash (11.3-76.7 in the Khabarovsk area and 77-245 in the Vladivostok area) than on artificially stressed Manchurian ash (2.2) or Oriental ash (10-59). Mortality of emerald ash borer larvae caused by different biotic factors (woodpecker predation, host plant resistance and/or undetermined diseases, and parasitism) varied with date, site, and ash species. In general, predation of emerald ash borer larvae by woodpeckers was low. While low rates (3-27%) of emerald ash borer larval mortality were caused by undetermined biotic factors on green ash between 2009 and 2011, higher rates (26-95%) of emerald ash borer larval mortality were caused by putative plant resistance in Oriental ash species in both regions. Little (<1%) parasitism of emerald ash borer larvae was observed in Khabarovsk; however, three hymenopteran parasitoids (Spathius sp., Atanycolus nigriventris Vojnovskaja-Krieger, and Tetrastichus planipennisi Yang) were observed attacking third - fourth instars of emerald ash borer in the Vladivostok area, parasitizing 0-8.3% of emerald ash borer larvae infesting Oriental ash trees and 7.3-62.7% of those on green ash trees (primarily by Spathius sp.) in two of the three study sites. Relevance of these findings to the classical biological control of emerald ash borer in newly invaded regions is discussed.

Effect of wildfires on physicochemical changes of watershed dissolved organic matter.

PubMed

Revchuk, Alex D; Suffet, I H

2014-04-01

Physicochemical characterization of dissolved organic carbon (DOC) provides essential data to describe watershed characteristics after drastic changes caused by wildfires. Post-fire watershed behavior is important for water source selection, management, and drinking water treatment optimization. Using ash and other burned vegetation fragments, a leaching procedure was implemented to describe physicochemical changes to watershed DOC caused by wildfires. Samples were collected after the 2007 and 2009 wildfires near Santa Barbara, California. Substantial differences in size distribution (measured by ultrafiltration), polarity (measured by polarity rapid assessment method), and the origin of leached DOC (measured by fluorescence) were observed between burned and unburned sites. Recently burned ash had 10 times the DOC leaching potential, and was dominated by large size fragments, compared to weathered 2-year-old ash. Charged DOC fractions were found to positively correlate with DOC size, whereas hydrophobic and hydrophilic DOC fractions were not. Proteins were only observed in recently burned ash and were indicative of recent post-fire biological activity.

Fabricaton of brick without burning process

NASA Astrophysics Data System (ADS)

Zultiniar; Fadli, A.; Yenti, S. R.; Drastinawati; Thariq, M. R. A.

2018-04-01

Brick is a material with many applications on building materials. The purpose of this research is to study the effect of fly ash addition and hardening time on mechanical properties of brick produced. Brick was formed by mixing cement, clay, water and fly ash with addition point was 0;0,3;0,6;0,9;1,2 kg weight. Brick was dried at room temperature for 7, 14 and 21 days. The result showed that compressive strength with addition 0,6 kg fly ash for 21 days was the the strongest where that’s value was 9,375 N/mm2. The highest porosity was get in on 21,34 % with 1,2 fly ash addition. The result of TCLP showed that for Pb, Cu, Cr content was still below the quality standards based on PP No.85 TH 1999 and still considered harmless. Leachate value for Pb of 3,10 mg/L, 1,213 mg/L for Cr and 4,374 mg/L for Cu.

Experimental study of influence characteristics of flue gas fly ash on acid dew point

NASA Astrophysics Data System (ADS)

Song, Jinhui; Li, Jiahu; Wang, Shuai; Yuan, Hui; Ren, Zhongqiang

2017-12-01

The long-term operation experience of a large number of utility boilers shows that the measured value of acid dew point is generally lower than estimated value. This is because the influence of CaO and MgO on acid dew point in flue gas fly ash is not considered in the estimation formula of acid dew point. On the basis of previous studies, the experimental device for acid dew point measurement was designed and constructed, and the acid dew point under different smoke conditions was measured. The results show that the CaO and MgO in the flue gas fly ash have an obvious influence on the acid dew point, and the content of the fly ash is negatively correlated with the temperature of acid dew point At the same time, the concentration of H2SO4 in flue gas is different, and the acid dew point of flue gas is different, and positively correlated with the acid dew point.

Methyl-orange and cadmium simultaneous removal using fly ash and photo-Fenton systems.

PubMed

Visa, Maria; Duta, Anca

2013-01-15

Wastewaters resulting from the textile and dye finishing industries need complex treatment for efficient removal of colour and other compounds existent in the dyeing and rising baths (heavy metals, surfactants, equalizers, etc.). Modified fly ash (FA) mixed with TiO(2) photocatalyst represent a viable option for simultaneous removal of dyes and heavy metals, and the optimized conditions are discussed in this paper for synthetic wastewaters containing methyl-orange (MO) and cadmium. For a cost-effective dye removal process, further tests were done, replacing the photocatalyst with a (photo)Fenton system. The optimized technological parameters (contact time, amount of fly ash and amount of Fe(2+)/H(2)O(2)) allow to reach removal efficiencies up to 88% for the heavy metal and up to 70% for the dye. The adsorption mechanisms and the process kinetic are discussed, also considering the possibility of in situ generation of the Fenton system, due to the fly ash composition. Copyright © 2012 Elsevier B.V. All rights reserved.

Optimal remediation of unconfined aquifers: Numerical applications and derivative calculations

NASA Astrophysics Data System (ADS)

Mansfield, Christopher M.; Shoemaker, Christine A.

1999-05-01

This paper extends earlier work on derivative-based optimization for cost-effective remediation to unconfined aquifers, which have more complex, nonlinear flow dynamics than confined aquifers. Most previous derivative-based optimization of contaminant removal has been limited to consideration of confined aquifers; however, contamination is more common in unconfined aquifers. Exact derivative equations are presented, and two computationally efficient approximations, the quasi-confined (QC) and head independent from previous (HIP) unconfined-aquifer finite element equation derivative approximations, are presented and demonstrated to be highly accurate. The derivative approximations can be used with any nonlinear optimization method requiring derivatives for computation of either time-invariant or time-varying pumping rates. The QC and HIP approximations are combined with the nonlinear optimal control algorithm SALQR into the unconfined-aquifer algorithm, which is shown to compute solutions for unconfined aquifers in CPU times that were not significantly longer than those required by the confined-aquifer optimization model. Two of the three example unconfined-aquifer cases considered obtained pumping policies with substantially lower objective function values with the unconfined model than were obtained with the confined-aquifer optimization, even though the mean differences in hydraulic heads predicted by the unconfined- and confined-aquifer models were small (less than 0.1%). We suggest a possible geophysical index based on differences in drawdown predictions between unconfined- and confined-aquifer models to estimate which aquifers require unconfined-aquifer optimization and which can be adequately approximated by the simpler confined-aquifer analysis.

Interspecific Proteomic Comparisons Reveal Ash Phloem Genes Potentially Involved in Constitutive Resistance to the Emerald Ash Borer

PubMed Central

Whitehill, Justin G. A.; Popova-Butler, Alexandra; Green-Church, Kari B.; Koch, Jennifer L.; Herms, Daniel A.; Bonello, Pierluigi

2011-01-01

The emerald ash borer (Agrilus planipennis) is an invasive wood-boring beetle that has killed millions of ash trees since its accidental introduction to North America. All North American ash species (Fraxinus spp.) that emerald ash borer has encountered so far are susceptible, while an Asian species, Manchurian ash (F. mandshurica), which shares an evolutionary history with emerald ash borer, is resistant. Phylogenetic evidence places North American black ash (F. nigra) and Manchurian ash in the same clade and section, yet black ash is highly susceptible to the emerald ash borer. This contrast provides an opportunity to compare the genetic traits of the two species and identify those with a potential role in defense/resistance. We used Difference Gel Electrophoresis (DIGE) to compare the phloem proteomes of resistant Manchurian to susceptible black, green, and white ash. Differentially expressed proteins associated with the resistant Manchurian ash when compared to the susceptible ash species were identified using nano-LC-MS/MS and putative identities assigned. Proteomic differences were strongly associated with the phylogenetic relationships among the four species. Proteins identified in Manchurian ash potentially associated with its resistance to emerald ash borer include a PR-10 protein, an aspartic protease, a phenylcoumaran benzylic ether reductase (PCBER), and a thylakoid-bound ascorbate peroxidase. Discovery of resistance-related proteins in Asian species will inform approaches in which resistance genes can be introgressed into North American ash species. The generation of resistant North American ash genotypes can be used in forest ecosystem restoration and urban plantings following the wake of the emerald ash borer invasion. PMID:21949771

Interspecific proteomic comparisons reveal ash phloem genes potentially involved in constitutive resistance to the emerald ash borer.

PubMed

Whitehill, Justin G A; Popova-Butler, Alexandra; Green-Church, Kari B; Koch, Jennifer L; Herms, Daniel A; Bonello, Pierluigi

2011-01-01

The emerald ash borer (Agrilus planipennis) is an invasive wood-boring beetle that has killed millions of ash trees since its accidental introduction to North America. All North American ash species (Fraxinus spp.) that emerald ash borer has encountered so far are susceptible, while an Asian species, Manchurian ash (F. mandshurica), which shares an evolutionary history with emerald ash borer, is resistant. Phylogenetic evidence places North American black ash (F. nigra) and Manchurian ash in the same clade and section, yet black ash is highly susceptible to the emerald ash borer. This contrast provides an opportunity to compare the genetic traits of the two species and identify those with a potential role in defense/resistance. We used Difference Gel Electrophoresis (DIGE) to compare the phloem proteomes of resistant Manchurian to susceptible black, green, and white ash. Differentially expressed proteins associated with the resistant Manchurian ash when compared to the susceptible ash species were identified using nano-LC-MS/MS and putative identities assigned. Proteomic differences were strongly associated with the phylogenetic relationships among the four species. Proteins identified in Manchurian ash potentially associated with its resistance to emerald ash borer include a PR-10 protein, an aspartic protease, a phenylcoumaran benzylic ether reductase (PCBER), and a thylakoid-bound ascorbate peroxidase. Discovery of resistance-related proteins in Asian species will inform approaches in which resistance genes can be introgressed into North American ash species. The generation of resistant North American ash genotypes can be used in forest ecosystem restoration and urban plantings following the wake of the emerald ash borer invasion.

Long-term modelling of fly ash and radionuclide emissions as well as deposition fluxes due to the operation of large oil shale-fired power plants.

PubMed

Vaasma, Taavi; Kaasik, Marko; Loosaar, Jüri; Kiisk, Madis; Tkaczyk, Alan H

2017-11-01

Two of the world's largest oil shale-fired power plants (PPs) in Estonia have been operational over 40 years, emitting various pollutants, such as fly ash, SO x , NO x , heavy metals, volatile organic compounds as well as radionuclides to the environment. The emissions from these PPs have varied significantly during this period, with the maximum during the 1970s and 1980s. The oil shale burned in the PPs contains naturally occurring radionuclides from the 238 U and 232 Th decay series as well as 40 K. These radionuclides become enriched in fly ash fractions (up to 10 times), especially in the fine fly ash escaping the purification system. Using a validated Gaussian-plume model, atmospheric dispersion modelling was carried out to determine the quantity and a real magnitude of fly ash and radionuclide deposition fluxes during different decades. The maximum deposition fluxes of volatile radionuclides ( 210 Pb and 210 Po) were around 70 mBq m -2 d -1 nearby the PPs during 1970s and 1980s. Due to the reduction of burned oil shale and significant renovations done on the PPs, the deposition fluxes were reduced to 10 mBq m -2 d -1 in the 2000s and down to 1.5 mBq m -2 d -1 in 2015. The maximum deposition occurs within couple of kilometers of the PPs, but the impacted area extends to over 50 km from the sources. For many radionuclides, including 210 Po, the PPs have been larger contributors of radionuclides to the environment via atmospheric pathway than natural sources. This is the first time that the emissions and deposition fluxes of radionuclides from the PPs have been quantified, providing the information about their radionuclide deposition load on the surrounding environment during various time periods. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Leaching of Aluminium In Spanish Clays, Coal Mining Wastes and Coal Fly Ashes by Sulphuric Acid.

NASA Astrophysics Data System (ADS)

Fernández, A. M.; Ibáñez, J. L.; Llavona, M. A.; Zapico, R.

The acid leaching of aluminium from several non traditional ores, bayerite, kaolinite, different clays, coal mining wastes and coal fly ashes, and the kinetic of their dissolution are described. The effects of time, temperature, acid concentration, sample calcination, particle size were examined. The leaching of aluminium is dependent on acid concentration and strongly on temperature. Generally, the time to reach a fixed percentage of dissolution decreases with increasing acid concentration in the range 6% to 40% acid by weight. On clays and coal mining wastes a good relation between Al removal and ratio kaolinite/illite was also observed at all temperatures and acid concentration tested. Coal fly ashes are particles that were heated at very high temperatures in the power station and Al compounds were transformed into mullite and so Al recovery was minor. Several rate equations describing the kinetics of the leach reaction were discussed and Kinetic parameters and activation energy values of samples are presented.

Recovery of gallium and vanadium from gasification fly ash.

PubMed

Font, Oriol; Querol, Xavier; Juan, Roberto; Casado, Raquel; Ruiz, Carmen R; López-Soler, Angel; Coca, Pilar; García Peña, Francisco

2007-01-31

The Puertollano Integrated Coal Gasification Combined Cycle (IGCC) Power Plant (Spain) fly ash is characterized by a relatively high content of Ga and V, which occurs mainly as Ga2O3 and as Ga3+ and V3+ substituting for Al3+ in the Al-Si fly ash glass matrix. Investigations focused on evaluating the potential recovery of Ga and V from these fly ashes. Several NaOH based extraction tests were performed on the IGCC fly ash, at different temperatures, NaOH/fly ash (NaOH/FA) ratios, NaOH concentrations and extraction times. The optimal Ga extraction conditions was determined as 25 degrees C, NaOH 0.7-1 M, NaOH/FA ratio of 5 L/kg and 6 h, attaining Ga extraction yields of 60-86%, equivalent to 197-275 mg of Ga/kg of fly ash. Re-circulation of leachates increased initial Ga concentrations (25-38 mg/L) to 188-215 mg/L, while reducing both content of impurities and NaOH consumption. Carbonation of concentrated Ga leachate demonstrated that 99% of the bulk Ga content in the leachate precipitates at pH 7.4. At pH 10.5 significant proportions of impurities, mainly Al (91%), co-precipitate while >98% of the bulk Ga remains in solution. A second carbonation of the remaining solution (at pH 7.5) recovers the 98.8% of the bulk Ga. Re-dissolution (at pH 0) of the precipitate increases Ga purity from 7 to 30%, this being a suitable Ga end product for further purification by electrolysis. This method produces higher recovery efficiency than currently applied for Ga on an industrial scale. In contrast, low V extraction yields (<64%) were obtained even when using extreme alkaline extraction conditions, which given the current marked price of this element, limits considerably the feasibility of V recovery from IGCC fly ash.

Geotechnical characterization of a Municipal Solid Waste Incineration Ash from a Michigan monofill.

PubMed

Zekkos, Dimitrios; Kabalan, Mohammad; Syal, Sita Marie; Hambright, Matt; Sahadewa, Andhika

2013-06-01

A field and laboratory geotechnical characterization study of a Municipal Solid Waste Incineration Ash disposed of at the Carleton Farms monofill in Michigan was performed. Field characterization consisted of field observations, collection of four bulk samples and performance of shear wave velocity measurements at two locations. Laboratory characterization consisted of basic geotechnical characterization, i.e., grain size distribution, Atterberg limits, specific gravity tests, compaction tests as well as moisture and organic content assessment followed by direct shear and triaxial shear testing. The test results of this investigation are compared to results in the literature. The grain size distribution of the samples was found to be very similar and consistent with the grain size distribution data available in the literature, but the compaction characteristics were found to vary significantly. Specific gravities were also lower than specific gravities of silicic soils. Shear strengths were higher than typically reported for sandy soils, even for MSWI ash specimens at a loose state. Strain rate was not found to impact the shear resistance. Significant differences in triaxial shear were observed between a dry and a saturated specimen not only in terms of peak shear resistance, but also in terms of stress-strain response. In situ shear wave velocities ranged from 500 to 800 m/s at a depth of about 8m, to 1100-1200 m/s at a depth of 50 m. These high shear wave velocities are consistent with field observations indicating the formation of cemented blocks of ash with time, but this "ageing" process in MSWI ash is still not well understood and additional research is needed. An improved understanding of the long-term behavior of MSWI ash, including the effects of moisture and ash chemical composition on the ageing process, as well as the leaching characteristics of the material, may promote unbound utilization of the ash in civil infrastructure. Copyright © 2013 Elsevier Ltd. All rights reserved.

AL(0) in municipal waste incinerator ash

NASA Astrophysics Data System (ADS)

Stipp, S. L.; Ronsbo, J. G.; Zunic, T. B.; Christensen, T. H.

2003-04-01

Disposal of municipal waste is a challenge to society. Waste volume is substantially decreased by incineration but residual ash usually contains a number of toxic components which must be immobilised to insure environmental protection. One element, chromium, is mobile and toxic in its oxidised state as Cr(VI) but it can be reduced to Cr(III) and immobilised. Reduction can be promoted by ash treatment with Fe(0) or Fe(II), but recent evidence shows that at least some Cr(VI) is reduced spontaneously in the ash. Aspects of ash behaviour suggest metallic aluminium as the reducing agent, but no direct evidence of Al(0) has been found until now. We examined filter ash from an energy-producing, municipal-waste incinerator (Vest-forbrænding) near Copenhagen. X-ray diffraction (XRD) identified expected salts of Na, K and Ca such as halite, sylvite, calcite, anhydrite and gypsum as well as quartz, feldspar and some hematite. Wave-dispersive electron microprobe produced elemen-tal maps of the ash; Al-rich areas were analysed quantitatively by comparison with standards. We identified metallic Al particles, averaging 50 to 100 micrometers in di-ameter, often with a fractured, glassy border of aluminum oxide. The particles were porous, explaining fast Cr(VI) reduction and they contained thin exsolution lamellae of Al-alloys of Pb and Cu or Mn, Fe and Ag, which provide clues of the Al(0) origin in the waste. Sometimes Al(0) occurred inside glassy globes of Al2O3. Time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and X-ray photoelectron spectroscopy (XPS) proved that surface Al concentrations on ash particles were below detection, confirming reactivity of the Al(0) bulk. The persistence of reduced Al through the highly oxidising combustion procedure comes as a surprise and is a benefit in the immobilisation of Cr(VI) from municipal-waste incineration residues.

Selenium(IV) and (VI) sorption by soils surrounding fly ash management facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hyun, S.; Burns, P.E.; Murarka, I.

2006-11-15

Leachate derived from unlined coal ash disposal facilities is one of the most significant anthropogenic sources of selenium to the environment. To establish a practical framework for predicting transport of selenium in ash leachate, sorption of Se(IV) and Se(VI) from 1 mM CaSO{sub 4} was measured for 18 soils obtained down-gradient from three ash landfill sites and evaluated with respect to several soil properties. Furthermore, soil attenuation from lab-generated ash leachate and the effect of Ca{sup 2+} and SO{sub 4}{sup 2-} concentrations as well as pH on both Se(IV) and Se(VI) was quantified for a subset of soils. For bothmore » Se(IV) and Se(VI), pH combined with either percentage clay or dithionite-citrate-bicarbonate (DCB)-extractable Fe described {gt} 80% of the differences in sorption across all soils, yielding an easy approach for making initial predictions regarding site-specific selenium transport to sensitive water bodies. Se(IV) consistently exhibited an order of magnitude greater sorption than Se(VI). Selenium sorption was highest at lower pH values, with Se(IV) sorption decreasing at pH values above 6, whereas Se(VI) decreased over the entire pH range (2.5-10). Using these pH adsorption envelopes, the likely effect of ash leachate-induced changes in soil pore water pH with time on selenium attenuation by down gradient soils can be predicted. Selenium sorption increased with increasing Ca{sup 2+} concentrations while SO{sub 4}2- suppressed sorption well above enhancements by Ca{sup 2+}. Soil attenuation of selenium from ash leachates agreed well with sorption measured from 1 mM CaSO{sub 4}, indicating that 1 mM CaSO{sub 4} is a reasonable synthetic leachate for assessing selenium behavior at ash landfill sites.« less

Treatment of fly ash for use in concrete

DOEpatents

Boxley, Chett [Park City, UT

2012-05-15

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

Treatment of fly ash for use in concrete

DOEpatents

Boxley, Chett [Park City, UT; Akash, Akash [Salt lake City, UT; Zhao, Qiang [Natick, MA

2012-05-08

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with an activator solution sufficient to initiate a geopolymerization reaction and for a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 35% of the foam index of the untreated fly ash, and in some cases less than 10% of the foam index of the untreated fly ash. The activator solution may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

Treatment of fly ash for use in concrete

DOEpatents

Boxley, Chett; Akash, Akash; Zhao, Qiang

2013-01-08

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with an activator solution sufficient to initiate a geopolymerization reaction and for a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 35% of the foam index of the untreated fly ash, and in some cases less than 10% of the foam index of the untreated fly ash. The activator solution may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

Microphysical Properties of Alaskan Volcanic Ash

NASA Astrophysics Data System (ADS)

Puthukkudy, A.; Espinosa, R.; Rocha Lima, A.; Remer, L.; Colarco, P. R.; Whelley, P.; Krotkov, N. A.; Young, K.; Dubovik, O.; Wallace, K.; Martins, J. V.

2017-12-01

Volcanic ash has the potential to cause a variety of severe problems for human health and the environment. Therefore, effective monitoring of the dispersion and fallout from volcanic ash clouds and characterization of the aerosol particle properties are essential. One way to acquire information from volcanic clouds is through satellite remote sensing: such images have greater coverage than ground-based observations and can present a "big picture" perspective. A challenge of remote sensing is that assumptions of certain properties of the target are often a pre-requisite for making accurate and quantitative retrievals. For example, detailed information about size distribution, sphericity, and optical properties of the constituent matter is needed or must be assumed. The same kind of information is also needed for atmospheric transport models to properly simulate the dispersion and fallout of volcanic ash. Presented here is a laboratory method to determine the microphysical and optical properties of volcanic ash samples collected from two Alaskan volcanoes with markedly different compositions. Our method uses a Polarized Imaging Nephelometer (PI-Neph) and a system that re-suspends the particles in an air flow. The PI-Neph measures angular light scattering and polarization of the re-suspended particles from 3o to 175o in scattering angle, with an angular resolution of 1o . Primary measurements include phase function and polarized phase function at three wavelengths (445nm, 532nm, and 661nm). Size distribution, sphericity, and complex refractive index are retrieved indirectly from the PI-Neph measurements using the GRASP (Generalized Retrieval of Aerosol and Surface Properties) inversion algorithm. We report the results of this method applied to samples from the Mt. Okmok (2008) and Mt. Katmai (1912) volcanic eruptions. To our knowledge, this is the first time direct measurements of phase matrix elements of ash from Mt. Okmok and Mt. Katmai have been reported. Retrieved microphysical properties show that Mt. Katmai ash is less absorbing than the Mt. Okmok ash in visible wavelengths. Phase function of these Alaskan volcanic ashes is smooth curve without any significant features. Phase function and polarized phase function measured do not exhibit strong spectral dependence in visible wavelengths.

Concentration of heavy metals in ash produced from Lithuanian forests

NASA Astrophysics Data System (ADS)

Baltrenaite, Edita; Pereira, Paulo; Butkus, Donatas; Úbeda, Xavier

2010-05-01

Wood ash contains important amounts of heavy metals. This quantity depends on burned specie, temperature of exposition and heat duration time. Due the high mineralization imposed by the temperatures, ash is used as lime product in agriculture and forests. Also, after a forest fire large quantities of ash are produced and distributed in soil surface. This mineralized organic matter can induce important environmental problems, including soil toxicity provoked by heavy metals leachates from ash. There is an extensive literature about heavy metals contents on ash in different species. However, it recently highlighted that the same species placed in different environments can respond diversely to same temperatures. This question is of major importance because temperature effects on severity can be a function of the plant communities instead of specie characteristics. These findings add a higher degree of complexity in the understanding of temperature effects on ash composition and consequent availability of heavy metals. The aim of this study is to compare the ash chemical heavy metal composition, Cobalt (Co), Chromium (Cr), Cooper (Cu), Silver (Ag), Lead (Pb), Nickel (Ni), Manganese (Mn) and Zinc (Zn), from Pinus sylvestris and Betula pendula, collected in key and representative areas of Lithuanian forests, located in southern, coastal and central part. Samples were collected from alive trees, taken to laboratory and air dried. Subsequently were crushed and submitted to muffle furnace at temperature of 550°C during two hours. The ash samples were digested and in a HNO3-HCl solution and then analysed with AAS. Comparisons between species and sites were performed with a Non-parametric one-way ANOVA‘s on rank transformed data followed by Tukey‘s HSD, significant at a p<0.05. Results showed significant difference between Co and Ag concentrations between Pinus sylvestris and Betula pendula. Also, significantly different concentrations of Pb, Cu, Ni and Mn were determined among investigated sites. No significant difference was found for Zn and Cr among investigated sites. Variation of metals between sites and stands can be explained by their age, flammability difference between plant communities and anthropogenic heavy metal load. These and other aspects will be discussed with more detail in the communication.

Thermal Barrier Coatings Chemically and Mechanically Resistant to High Temperature Attack by Molten Ashes

NASA Astrophysics Data System (ADS)

Gledhill, Andrew

Thermal barrier coatings (TBCs) are ceramic coatings used on component in the hottest sections of gas turbine engines, used for power generation and aviation. These coatings insulate the underlying metal components and allow for much higher engine operating temperatures, improving the engine efficiency. These increase temperatures engender a new set of materials problems for TBCs. Operating temperatures in engines are now high enough for silicate impurities, either present in the fuel or ingested into the engines, to melt and adhere to the surface of the TBCs. The effects of four such impurities, two coal fly ashes, a petroleum coke-fly ash blend, and volcanic ash from the Eyjafjallajokull volcano were tested with conventional yttria-stabilized zirconia (YSZ) coatings, and found to penetrate through the entire thickness of the coating. This penetration reduces the strain tolerance of the coatings, and can result in premature failure. Testing on a newly built thermal gradient burner rig with simultaneous injection of ash impurities has shown a reduction of life up to 99.6% in these coatings when ash is present. Coatings of an alternative ceramic, gadolinium zirconate (Gd2Zr 2O7), were found to form a dense reaction layer with each of these impurities, preventing further penetration of the molten ash. This dense layer also reduces the strain tolerance, but these coatings were found to have a significantly higher life than the YSZ coatings. Testing with a small amount of ash baked onto the samples showed thirteen times the life of YSZ coatings. When the ash is continuously sprayed onto the hot sample, the life of the Gd2Zr2O7 coatings was nearly twice that of the YSZ. Finally, a delamination model was employed to explain the degradation of both types of coatings. This elastic model that takes into account the degree of penetration, differential cooling in thermal gradient testing, and thermal expansion mismatch with the underlying substrate, predicted the failure of YSZ coatings with the observed degree of penetration. The model shows that deposition optimization can be employed to further enhance the life of Gd 2Zr2O7coatings.

Spatial and temporal trends in contaminant concentrations in Hexagenia nymphs following a coal ash spill at the Tennessee Valley Authority's Kingston Fossil Plant

DOE PAGES

Baker, Tyler F; Jett, Robert Trent; Smith, John G.; ...

2016-02-25

A dike failure at the Tennessee Valley Authority Kingston Fossil Plant in East Tennessee, United States, in December 2008, released approximately 4.1 million m3 of coal ash into the Emory River. From 2009 through 2012, samples of mayfly nymphs ( Hexagenia bilineata) were collected each spring from sites in the Emory, Clinch, and Tennessee Rivers upstream and downstream of the spill. Samples were analyzed for 17 metals. Concentrations of metals were generally highest the first 2 miles downstream of the spill, and then decreased with increasing distance from the spill. Arsenic, B, Ba, Be, Mo, Sb, Se, Sr, and Vmore » appeared to have strong ash signatures, whereas Co, Cr, Cu, Ni, and Pb appeared to be associated with ash and other sources. Furthermore, the concentrations for most of these contaminants were modest and are unlikely to cause widespread negative ecological effects. Trends in Hg, Cd, and Zn suggested little (Hg) or no (Cd, Zn) association with ash. Temporal trends suggested that concentrations of ash-related contaminants began to subside after 2010, but because of the limited time period of that analysis (4 yr), further monitoring is needed to verify this trend. The present study provides important information on the magnitude of contaminant exposure to aquatic receptors from a major coal ash spill, as well as spatial and temporal trends for transport of the associated contaminants in a large open watershed. Environ Toxicol Chem 2016;35:1159 1171. Published 2015 Wiley Periodicals Inc. on behalf of SETAC. This article is a US government work and, as such, is in the public domain in the United States of America.« less

The effect of nano-silica fertilizer concentration and rice hull ash doses on soybean (Glycine max (L.) Merrill) growth and yield

NASA Astrophysics Data System (ADS)

Suciaty, T.; Purnomo, D.; Sakya, A. T.; Supriyadi

2018-03-01

Agriculture is facing a number of challenges included limited water supply, low nutrient use efficiency, etc affected by climate change. Nano-silica is a product of nanotechnology, the frontier technologies to enhance crop productivity under climate change threats. The purpose of the research was to investigate the effects of nano silica concentration and rice hull ash on growth and yield of soybean. The experiment was conducted at Gagasari village, Cirebon, West Java from March until June 2017. The treatments were arranged by using factorial completely randomized block design with two factors. The first factor was a concentration of nano silica fertilizer consisted of four levels i.e., 0, 1.75, 2.5, and 3.75 ml.l‑1. The second factor was doses of rice hull ash consisted of four levels i.e., 0, 1, 2, and 3 ton.ha‑1. Each treatment combinations was repeated three times. The result showed that concentration of nano silica individually affected the number of leaves and number of branches, NAR and RGR, productive branches at 21, 30-45, and 35 daps, respectively. It also affected the seed dry weight plant‑1 and plot‑1. Meanwhile, doses of rice hull ash affected LAI, NAR, and RGR, 15-30, and 30-45 dap, respectively. Dry seed weight plot‑1 was also affected by doses of rice hull ash. There was an interaction effect between nano-silica concentration and doses of rice hull ash on number pods.plant‑1. Combinations of 2.5 ml.l‑1 nano-silica and 3 ton.ha‑1 of rice hull ash gave the highest number pods.plant‑1.

Volcanic ash in ancient Maya ceramics of the limestone lowlands: implications for prehistoric volcanic activity in the Guatemala highlands

NASA Astrophysics Data System (ADS)

Ford, Anabel; Rose, William I.

1995-07-01

In the spirit of collaborative research, Glicken and Ford embarked on the problem of identifying the source of volcanic ash used as temper in prehistoric Maya ceramics. Verification of the presence of glass shards and associated volcanic mineralogy in thin sections of Maya ceramics was straightforward and pointed to the Guatemala Highland volcanic chain. Considering seasonal wind rose patterns, target volcanoes include those from the area west of and including Guatemala City. Joint field research conducted in 1983 by Glicken and Ford in the limestone lowlands of Belize and neighboring Guatemala, 300 km north of the volcanic zone and 150 km from the nearest identified ash deposits, was unsuccessful in discovering local volcanic ash deposits. The abundance of the ash in common Maya ceramic vessels coupled with the difficulties of long-distance procurement without draft animals lead Glicken to suggest that ashfall into the lowlands would most parsimoniously explain prehistoric procurement; it literally dropped into their hands. A major archaeological problem with this explanation is that the use of volcanic ash occurring over several centuries of the Late Classic Period (ca. 600-900 AD). To accept the ashfall hypothesis for ancient Maya volcanic ash procurement, one would have to demonstrate a long span of consistent volcanic activity in the Guatemala Highlands for the last half of the first millennium AD. Should this be documented through careful petrographic, microprobe and tephrachronological studies, a number of related archaeological phenomena would be explained. In addition, the proposed model of volcanic activity has implications for understanding volcanism and potential volcanic hazards in Central America over a significantly longer time span than the historic period. These avenues are explored and a call for further collaborative research of this interdisciplinary problem is extended in this paper.

D Visualization of Volcanic Ash Dispersion Prediction with Spatial Information Open Platform in Korea

NASA Astrophysics Data System (ADS)

Youn, J.; Kim, T.

2016-06-01

Visualization of disaster dispersion prediction enables decision makers and civilian to prepare disaster and to reduce the damage by showing the realistic simulation results. With advances of GIS technology and the theory of volcanic disaster prediction algorithm, the predicted disaster dispersions are displayed in spatial information. However, most of volcanic ash dispersion predictions are displayed in 2D. 2D visualization has a limitation to understand the realistic dispersion prediction since its height could be presented only by colour. Especially for volcanic ash, 3D visualization of dispersion prediction is essential since it could bring out big aircraft accident. In this paper, we deals with 3D visualization techniques of volcanic ash dispersion prediction with spatial information open platform in Korea. First, time-series volcanic ash 3D position and concentrations are calculated with WRF (Weather Research and Forecasting) model and Modified Fall3D algorithm. For 3D visualization, we propose three techniques; those are 'Cube in the air', 'Cube in the cube', and 'Semi-transparent plane in the air' methods. In the 'Cube in the Air', which locates the semitransparent cubes having different color depends on its particle concentration. Big cube is not realistic when it is zoomed. Therefore, cube is divided into small cube with Octree algorithm. That is 'Cube in the Cube' algorithm. For more realistic visualization, we apply 'Semi-transparent Volcanic Ash Plane' which shows the ash as fog. The results are displayed in the 'V-world' which is a spatial information open platform implemented by Korean government. Proposed techniques were adopted in Volcanic Disaster Response System implemented by Korean Ministry of Public Safety and Security.

The Role of Authigenic Volcanic Ash in Marine Sediment

NASA Astrophysics Data System (ADS)

Scudder, R.; McKinley, C. C.; Thomas, D. J.; Murray, R. W.

2016-12-01

Marine sediments are a fundamental archive of the history of weathering and erosion, biological productivity, volcanic activity, patterns of deep-water formation and circulation, and a multitude of other earth, ocean, and atmosphere processes. In particular, the record and consequences of volcanic eruptions have long fascinated humanity. Volcanic ash layers are often visually stunning, and can have thicknesses of 10s of cm or more. While the ash layer records are of great importance by themselves, we are missing a key piece of information-that of the very fined grained size fractions. Dispersed ash is the very fine grained-component that has either been mixed into the bulk sediment by bioturbation, or is deposited from subaqueous eruptions, erosion of terrestrial deposits, general input during time periods of elevated global volcanism, or other mechanisms, plays an important role in the marine sediment. The presence of dispersed ash in the marine record has previously been relatively over-looked as it is difficult to identify petrographically due to its commonly extremely fine grain size and/or alteration to authigenic clay. The dispersed ash, either altered or unaltered, is extremely difficult to differentiate from detrital/terrigenous/authigenic clay, as they are all "aluminosilicates". Here we apply a combined geochemical, isotopic, and statistical technique that enables us to resolve volcanic from detrital terrigenous inputs at DSDP/ODP/IODP sites from both the Brazil Margin and the Northwest Pacific Oceans. Incorporating the combined geochemical/statistical techniques with radiogenic isotope records allows us to address paleoceanographic questions in addition to studies of the effect of sediment fluxes on carbon cycling, the relationship between volcanic ash and biological productivity of the open ocean and nutrient availability for subseafloor microbial life.

Enhancement of mercury capture by the simultaneous addition of hydrogen bromide (HBr) and fly ashes in a slipstream facility.

PubMed

Cao, Yan; Wang, Quan-Hai; Li, Jun; Cheng, Jen-Chieh; Chan, Chia-Chun; Cohron, Marten; Pan, Wei-Ping

2009-04-15

Low halogen content in tested Powder River Basin (PRB) coals and low loss of ignition content (LOI) in PRB-derived fly ash were likely responsible for higher elemental mercury content (averaging about 75%) in the flue gas and also lower mercury capture efficiency by electrostatic precipitator (ESP) and wet-FGD. To develop a cost-effective approach to mercury capture in a full-scale coal-fired utility boiler burning PRB coal, experiments were conducted adding hydrogen bromide (HBr) or simultaneously adding HBr and selected fly ashes in a slipstream reactor (0.152 x 0.152 m) under real flue gas conditions. The residence time of the flue gas inside the reactorwas about 1.4 s. The average temperature of the slipstream reactor was controlled at about 155 degrees C. Tests were organized into two phases. In Phase 1, only HBr was added to the slipstream reactor, and in Phase 2, HBr and selected fly ash were added simultaneously. HBr injection was effective (>90%) for mercury oxidation at a low temperature (155 degrees C) with an HBr addition concentration of about 4 ppm in the flue gas. Additionally, injected HBr enhanced mercury capture by PRB fly ash in the low-temperature range. The mercury capture efficiency, attesting conditions of the slipstream reactor, reached about 50% at an HBr injection concentration of 4 ppm in the flue gas. Compared to only the addition of HBr, simultaneously adding bituminous-derived fly ash in a minimum amount (30 lb/MMacf), together with HBr injection at 4 ppm, could increase mercury capture efficiency by 30%. Injection of lignite-derived fly ash at 30 lb/MMacf could achieve even higher mercury removal efficiency (an additional 35% mercury capture efficiency compared to HBr addition alone).

Diffusive dynamics of nanoparticles in ultra-confined media

DOE PAGES

Jacob, Jack Deodato; Conrad, Jacinta; Krishnamoorti, Ramanan; ...

2015-08-10

Differential dynamic microscopy (DDM) was used to investigate the diffusive dynamics of nanoparticles of diameter 200 400 nm that were strongly confined in a periodic square array of cylindrical nanoposts. The minimum distance between posts was 1.3 5 times the diameter of the nanoparticles. The image structure functions obtained from the DDM analysis were isotropic and could be fit by a stretched exponential function. The relaxation time scaled diffusively across the range of wave vectors studied, and the corresponding scalar diffusivities decreased monotonically with increased confinement. The decrease in diffusivity could be described by models for hindered diffusion that accountedmore » for steric restrictions and hydrodynamic interactions. The stretching exponent decreased linearly as the nanoparticles were increasingly confined by the posts. Altogether, these results are consistent with a picture in which strongly confined nanoparticles experience a heterogeneous spatial environment arising from hydrodynamics and volume exclusion on time scales comparable to cage escape, leading to multiple relaxation processes and Fickian but non-Gaussian diffusive dynamics.« less

Manufacturing technology and application of hemp cigarette paper with dense ash integration

NASA Astrophysics Data System (ADS)

Yao, Yu; Jian-bo, Zhan; Hao, Wan; Ying, Zhang; Li-wei, Li; Jiang, Yu; Ting-ting, Yu; Jiao, Xie; Bao-shan, Yue

2017-04-01

Cigarette paper, as one of the significant materials used for combustion, has special and direct influence on the smoke, also directly influencing the ash appearance of cigarettes before and after combustion. In this paper, full hemp cigarette paper was prepared through creative beating and mixing slurry technology, and the advantages of the preparation process were analyzed. Full hemp cigarette paper was creatively applied to the preparation and verification of slim cigarettes, and the ash integration effect in the process of burning and its influence on whiteness were verified. At the same time, the physical and chemical indexes of cigarette paper were tested and studied, and sensory evaluation was applied to verify the effect of cigarette paper on sensory quality.

Advances in Volcanic Ash Cloud Photogrammetry from Space

NASA Astrophysics Data System (ADS)

Zaksek, K.; von der Lieth, J.; Merucci, L.; Hort, M. K.; Gerst, A.; Carboni, E.; Corradini, S.

2015-12-01

The quality of ash dispersion prediction is limited by the lack of high quality information on eruption source parameters. One of the most important one is the ash cloud top height (ACTH). Because of well-known uncertainties of currently operational methods, photogrammetric methods can be used to improve height estimates. Some satellites have on board multiangular instruments that can be used for photogrammetrical observations. Volcanic ash clouds, however, can move with velocities over several m/s making these instruments inappropriate for accurate ACTH estimation. Thus we propose here two novel methods tested on different case studies (Etna 2013/11/23, Zhupanovsky 2014/09/10). The first method is based on NASA program Crew Earth observations from International Space Station (ISS). ISS has a lower orbit than most operational satellites, resulting in a shorter minimal time between two images required to produce a suitable parallax. In addition, images made by the ISS crew are taken by a full frame sensor and not a line scanner that most operational satellites use. Such data make possible to observe also short time evolution of clouds. The second method is based on the parallax between data retrieved from two geostationary instruments. We implemented a combination of MSG SEVIRI (HRV band; 1000 m nadir spatial resolution, 5 min temporal resolution) and METEOSAT7 MVIRI (VIS band, 2500 m nadir spatial resolution, 30 min temporal resolution). The procedure works well if the data from both satellites are retrieved nearly simultaneously. However, MVIRI does not retrieve the data at exactly the same time as SEVIRI. To compensate for advection in the atmosphere we use two sequential SEVIRI images (one before and one after the MVIRI retrieval) and interpolate the cloud position from SEVIRI data to the time of MVIRI retrieval.

Inward transport of a toroidally confined plasma subject to strong radial electric fields

NASA Technical Reports Server (NTRS)

Roth, J. R.; Krawczonek, W. M.; Powers, E. J.; Hong, J.; Kim, Y.

1977-01-01

The paper aims at showing that the density and confinement time of a toroidal plasma can be enhanced by radial electric fields far stronger than the ambipolar values, and that, if such electric fields point into the plasma, radially inward transport can result. The investigation deals with low-frequency fluctuation-induced transport using digitally implemented spectral analysis techniques and with the role of strong applied radial electric fields and weak vertical magnetic fields on plasma density and particle confinement times in a Bumpy Torus geometry. Results indicate that application of sufficiently strong radially inward electric fields results in radially inward fluctuation-induced transport into the toroidal electrostatic potential well; this inward transport gives rise to higher average electron densities and longer particle confinement times in the toroidal plasma.

Soot, organics and ultrafine ash from air- and oxy-fired coal ...

EPA Pesticide Factsheets

This paper is concerned with determining the effects of oxy-combustion of coal on the composition of the ultrafine fly ash. To this end, a 10 W externally heated entrained flow furnace was modified to allow the combustion of pulverized coal in flames under practically relevant stoichiometric ratios (SR = 1.2-1.4), but with the ability to maintain constant residence times (2.3 s). Experiments were conducted using a pulverized bituminous coal under air-combustion and three oxy-combustion inlet oxygen conditions (28, 32, and 36%). Size-classified fly ash samples were collected, and measurements focused on the composition of the total and ultrafine (<0.6 µm) fly ash produced, in particular the soot, elemental carbon (EC), and organic carbon (OC) fractions. Results indicate that although the total fly ash carbon, as measured by loss on ignition, was always acceptably low (<2%) with all three oxy-combustion conditions lower than air-combustion, the ultrafine fly ash for both air-fired and oxy-fired combustion conditions consists primarily of carbonaceous material (50-95%). Subsequent analyses of the carbonaceous component on particles <0.6 µm by a thermal optical method showed that large fractions (52-93%) consisted of OC rather than EC, as expected. This observation was supported by thermogravimetric analysis indicating that for the air, 28% oxy, and 32% oxy conditions, 14-71% of this material may be OC volatilizing between 100 and 550 °C with the remaining

The High Teperature Influence on Geopolymer Fly Ash Mixture’s Compressisive Strength with Insudtrial Waste Material Substitution

NASA Astrophysics Data System (ADS)

Bayuaji, R.; Wibowo, B.; Subekti, S.; Santoso, S. E.; Hardiyanto, E.; Kaelani, Y.; Mallu, L. L.

2017-11-01

This research aimed to figure out the influence of fly ash mixture from the industrial waste at the temperatures of 150°C, 450°C, 750°C viewed from the strength and resistance of geopolymer paste. As a result, cement will be substituted by industrial waste like fly ash. This experimental research was conducted on the mix design of geopolymer concrete which was made by dimension with 2.5 cm in diameter and 5 cm in height from four mixture composition of fly ash and industrial waste i.e. 100% fly ash, 50% fly ash+50% bottom ash, 50% fly ash+50% sandblast, and 50% fly ash+50% carbide waste. Each mixture was tested in terms of porosity and compressive strength. In conclusion, in the mixture of 50% fly ash+50% Sandblast and 50% fly ash+50% bottom ash in 12 molars, 1.5 activator comparison can be used to substitute fly ash at high temperature. Meanwhile, the mixture of 50% fly ash+50% carbide waste in 8 molars, 0.5 activator comparison has very small strength remaining if it is compared to the mixture of fly ash and other industrial waste (Bottom ash and Sandblast). The performance of mixture paste of 50% fly ash+50% carbide waste was very vulnerable after being burnt. Consequently, it cannot be used as the main structure at high temperature.

Large volcanic eruptions and the PETM: Geochemistry from the Fur Formation, Denmark

NASA Astrophysics Data System (ADS)

Jones, Morgan; Svensen, Henrik; Tegner, Christian; Planke, Sverre; Willumsen, Pi

2015-04-01

The opening of the North Atlantic Ocean during the early Cenozoic was accompanied by substantial volcanism that resulted in the deposition of numerous ash layers over much of northern Europe. This volcanism was contemporaneous with the extreme greenhouse climate of the Palaeocene-Eocene Thermal Maximum (PETM), and is therefore of particular interest for volcanism-climate interactions. The island of Fur, northern Denmark, contains abundant outcrops of volcanic ash layers deposited in a shallow marine environment. Over 179 distinct ash horizons (those greater than ~1 cm are numbered #-39 to #+140) are found within the ~60 m thick Fur Formation. The ash layers are predominantly black and composed of volcanic glass particles ranging from silt to sand in size. Each bed is normally graded and lacks any evidence of significant reworking. There were no volcanoes in the vicinity of Fur during this time, and the outcrops are >700 km from the break-up axis, indicating that at least some of the ash layers were formed during very large eruptions and transported a long way from the source volcanoes. A few thick grey ash layers (e.g. #-33 and #+19) are believed to have originated from volcanoes in East Greenland. Here we present geochemical data from two key sections within the Fur Formation, a beach section at Stolleklint where ashes #-34 to #-31 are exposed, and a quarry section at Jenshøj that covers ashes #+17 to #+35. The #-33 and #+19 ashes are both prominent marker horizons around 15-20 cm thick. The Stolleklint section is clay rich while the quarry section is dominated by diatomite. At Stolleklint, bulk rock total organic carbon (TOC) δ13C values throughout a 1.5 m section are relatively steady at -30.7 to -31.7 o typical of the carbon isotope excursion values of the PETM at Fur. Just above ash layer #-33, δ13C = -27.9 o characteristic of post-PETM values. The bulk rock TOC is high, 1.5 to 4 wt. %. The post-PETM quarry section is much poorer in organic material (0-0.5 wt. % TOC). Values of δ13C are more varied than at Stolleklint, scatter around -28.0 o in the lower 0.5 m. A small negative δ13C excursion occurs just above the thick #+19 ash layer, followed by a slow recovery to less negative values up section. This suggests a possible causal relation between the ash deposition and the carbon isotope record, as diminished primary productivity is typified by negative δ13C TOC values. These results indicate that North-Atlantic volcanism had significant repercussions and could have played a role in the termination of the PETM.

The aggregation efficiency of very fine volcanic ash

NASA Astrophysics Data System (ADS)

Del Bello, E.; Taddeucci, J.; Scarlato, P.

2013-12-01

Explosive volcanic eruptions can discharge large amounts of very small sized pyroclasts (under 0.090 mm) into the atmosphere that may cause problems to people, infrastructures and environment. The transport and deposition of fine ash are ruled by aggregation that causes premature settling of fine ash and, as consequence, significantly reduces the concentration of airborne material over long distances. Parameterizing the aggregation potential of fine ash is then needed to provide accurate modelling of ash transport and deposition from volcanic plumes. Here we present the first results of laboratory experiments investigating the aggregation efficiency of very fine volcanic particles. Previous laboratory experiments have shown that collision kinetic and relative humidity provide the strongest effect on aggregation behaviour but were only limited to particles with size > 0.125 mm. In our work, we focus on natural volcanic ash at ambient humidity with particles size < 0.090 mm, by taking into account the effect of grain size distribution on aggregation potential. Two types of ash were used in our experiments: fresh ash, collected during fall-out from a recent plume-forming eruption at Sakurajima (Japan -July 2013) and old ash, collected from fall-out tephra deposits at Campi Flegrei (Italy, ca. 10 ka), to account for the different chemical composition and morphoscopic effects of altered ash on aggregation efficiency. Total samples were hand sieved to obtain three classes with unimodal grain size distributions (<0.090 mm, <0.063 mm, <0.032 mm). Bimodal grain size distributions were also obtained by mixing the three classes in different proportions. During each experiments, particles were sieved from the top of a transparent tank where a fan, placed at the bottom, allows turbulent dispersion of particles. Collision and sticking of particles on a vertical glass slide were filmed with a high speed cameras at 6000 fps. Our lenses arrangement provide high image resolution allowing to capture particles down to 0.005 mm in diameter. Video sequences of particles motion and collision were then processed with image analysis and particle tracking tools to determine i) the particle number density and ii) the grain size distribution of particles in the turbulent dispersion, and iii) the number of adhered particles as a function of time. Optical laser granulometry provided constrains on grain size distribution of ash particles effectively adhered to the glass slide at the end of each run. Results obtained from our data-set allowed to provide a relationship for determining aggregation rate as a function of particle number density across a range of particle size distributions. This empirical model can be used to determine the aggregation fraction starting from a given total grain size distribution, thus providing fundamental parameters to incorporate aggregation into numerical models of ash dispersal and deposition.

Volcanic Ash Cloud Observations with the DLR-Falcon over Europe during Airspace Closure

NASA Astrophysics Data System (ADS)

Schumann, Ulrich; Weinzierl, Bernadett; Reitebuch, Oliver; Minikin, Andreas; Schlager, Hans; Rahm, Stephan; Scheibe, Monika; Lichtenstern, Michael; Forster, Caroline

2010-05-01

At the time of the EGU conference, the volcano ash plume originating from the Eyjafjallajökull volcano eruption in Iceland was probed during 9 flights with the DLR Falcon research aircraft in the region between Germany and Iceland at 1-11 km altitudes between April 19 and May 3, 2010. The Falcon was instrumented with a downward looking, scanning 2-µm-Wind-Lidar (aerosol backscattering and horizontal wind, 100 m vertical resolution), and several in-situ instruments. The particle instrumentation, including wing station probes (PCASP, FSSP-300) cover particle number and size from 5 nm to some tens of µm. Further in-situ instruments measured O3, CO, SO2, H2O, and standard meteorological parameters. Flight planning was based on numerical weather forecasts, trajectory-based particle-dispersion models, satellite observations and ground based Lidar observations, from many sources. During the flight on April 19, 2010, layers of volcanic ash were detected first by Lidar and then probed in-situ. The horizontal and vertical distribution of the volcanic ash layers over Eastern Germany was highly variable at that time. Calculations with the particle dispersion model FLEXPART indicate that the volcanic ash plumes measured by the Falcon had an age of 4-5 days. The concentrations of large particles measured in the volcanic aerosol layers are comparable to concentrations measured typically in fresh (age < 2 days) Saharan dust plumes. An estimation of the particle mass concentration in the elevated volcanic ash plume probed as part of a vertical profile over Leipzig at about 4 km altitude yields 60 µg/m3 (possibly 100 µg/m3), with an uncertainty of factor two. Of the total mass only less than 10 percent was residing in the particle size range below 2.5 µm. This emphasizes the need for adequate instrumentation to fully capture the size distribution of volcanic ash. During April 29-May 3, a sequence of flights has been performed between Germany, Scotland, and Iceland. Lidar measurements have been performed in a distance between 0-200 km downstream the Eyjafjal Volcano in Iceland. On May 2, the Lidar and insitu measurements occurred above and within the upper part of the ash plume over the North Atlantic in a quasi-Lagrangian experiment 7 h later.. The data are now being used to determine the volumetric flow in the plume and the mass flux of particles in the size range of up to about 30 micrometers. Major scientific and operational conclusions, include: - Falcon measurements have been performed between April 19 and May 3, 2010: with 2- mm-Lidar, in-situ aerosols, CO, O3, SO2, H2O - Particles sizes measured: 10 nm - 30 µm age dependent (mainly silicate, ammonia sulfate, more Na, K than in Saharan dust), - Mass loading (about 60 µg/m3, Leipzig, 5 days) comparable to Saharan dust (< 0.2 mg/m3) - 200 km distance, 3-4 h age: 40 km wide, 2 km thick, 15 m/s, sharply edged, strong wet convective turbulence, well mixed? - 450 km distance (same plume), 7 h age: at upper plume edge: 400-3400 µg/m3, no 2-DC probe particles, mass flux > 3000 kg/s, strong chemistry - Lidar signal and FSSP-300 signal strongly dependent on refractive index, ash density, particle size spectrum 1- 50 µm - Mid-European airspace closure was justified until Sat. April 17; thereafter ageing ash clouds dominated. - Keflavik/Iceland was found to be free of ash as predicted on April 29 - May 2 - The Quality of forecasts was found to be quite reliable for aviation planning - For the future we recommend combinations of models + lidar + satellite + in-situ - We suggest an improved linking between operations and academia - The DLR Falcon will continue to operate as Emergency Aircraft for some time Further scientific investigations (ash plume dispersion, aerosol ageing, mass concentration estimates, heterogeneous chemistry, comparison to other observations and models) have been initiated. The results had been provided to the German Weather Service (DWD) and others partly during the flights by satellite telephone and within 24 hours as quicklooks, and made available to the public by internet. The results had immediate impact on the decisions of the responsible agencies in Germany and the Volcanic Ash Advisory Centre (VAAC) in London. After the flights the Falcon inspections showed no obvious damage due to volcanic ash impact.

Electrification of Shaken Granular Flows as a Model of Natural Storm Charging

NASA Astrophysics Data System (ADS)

Kara, O.; Nordsiek, F.; Lathrop, D. P.

2015-12-01

The charging of particulates in nature is widespread and observed in thunderstorms, volcanic ash clouds, thunder-snow, and dust storms. However the mechanism of charge separation at large (> 1km) scale is poorly understood. We perform simple laboratory experiments to better understand the collective phenomena involved in granular electrification. We confine granular particles in an oscillating cylindrical chamber which is enclosed and sealed by two conducting plates. The primary measurement is the voltage difference between the two plates. We find that collective effects occurring in the bulk of the material play a significant role in the electrification process. We extend that by addition of photodetection capabilities to the experimental chamber to detect electrical discharges between the particles and each other and the plates. We present measurements of electrical discharges in addition to the slower dynamics of voltage variation in the system.

Quaternary low-angle slip on detachment faults in Death Valley, California

USGS Publications Warehouse

Hayman, N.W.; Knott, J.R.; Cowan, D.S.; Nemser, E.; Sarna-Wojcicki, A. M.

2003-01-01

Detachment faults on the west flank of the Black Mountains (Nevada and California) dip 29??-36?? and cut subhorizontal layers of the 0.77 Ma Bishop ash. Steeply dipping normal faults confined to the hanging walls of the detachments offset layers of the 0.64 Ma Lava Creek B tephra and the base of 0.12-0.18 Ma Lake Manly gravel. These faults sole into and do not cut the low-angle detachments. Therefore the detachments accrued any measurable slip across the kinematically linked hanging-wall faults. An analysis of the orientations of hundreds of the hanging-wall faults shows that extension occurred at modest slip rates (<1 mm/yr) under a steep to vertically oriented maximum principal stress. The Black Mountain detachments are appropriately described as the basal detachments of near-critical Coulomb wedges. We infer that the formation of late Pleistocene and Holocene range-front fault scarps accompanied seismogenic slip on the detachments.

Polymer chain dynamics under nanoscopic confinements.

PubMed

Kimmich, Rainer; Fatkullin, Nail; Mattea, Carlos; Fischer, Elmar

2005-02-01

It is shown that the confinement of polymer melts in nanopores leads to chain dynamics dramatically different from bulk behavior. This so-called corset effect occurs both above and below the critical molecular mass and induces the dynamic features predicted for reptation. A spinodal demixing technique was employed for the preparation of linear poly(ethylene oxide) (PEO) confined to nanoscopic strands that are in turn embedded in a quasi-solid and impenetrable methacrylate matrix. Both the molecular weight of the PEO and the mean diameter of the strands were varied to a certain degree. The chain dynamics of the PEO in the molten state was examined with the aid of field-gradient NMR diffusometry (time scale, 10(-2)-10(0) s) and field-cycling NMR relaxometry (time scale, 10(-9)-10(-4) s). The dominating mechanism for translational displacements probed in the nanoscopic strands by either technique is shown to be reptation. On the time scale of spin-lattice relaxation time measurements, the frequency dependence signature of reptation (i.e., T1 approximately nu(3/4)) showed up in all samples. A "tube" diameter of only 0.6 nm was concluded to be effective on this time scale even when the strand diameter was larger than the radius of gyration of the PEO random coils. This corset effect is traced back to the lack of the local fluctuation capacity of the free volume in nanoscopic confinements. The confinement dimension is estimated at which the crossover from confined to bulk chain dynamics is expected.

Ground-based weather radar remote sensing of volcanic ash explosive eruptions

NASA Astrophysics Data System (ADS)

Marzano, F. S.; Marchiotto, S.; Barbieri, S.; Giuliani, G.; Textor, C.; Schneider, D. J.

2009-04-01

The explosive eruptions of active volcanoes with a consequent formation of ash clouds represent a severe threat in several regions of the urbanized world. During a Plinian or a sub-Plinian eruption the injection of large amounts of fine and coarse rock fragments and corrosive gases into the troposphere and lower stratosphere is usually followed by a long lasting ashfall which can cause a variety of damages. Volcanic ash clouds are an increasing hazard to aviation safety because of growing air traffic volumes that use more efficient and susceptible jet engines. Real-time and areal monitoring of a volcano eruption, in terms of its intensity and dynamics, is not always possible by conventional visual inspections, especially during worse visibility periods which are quite common during eruption activity. Remote sensing techniques both from ground and from space represent unique tools to be exploited. In this respect, microwave weather radars can gather three-dimensional information of atmospheric scattering volumes up several hundreds of kilometers, in all weather conditions, at a fairly high spatial resolution (less than a kilometer) and with a repetition cycle of few minutes. Ground-based radar systems represent one of the best methods for determining the height and volume of volcanic eruption clouds. Single-polarization Doppler radars can measure horizontally-polarized power echo and Doppler shift from which ash content and radial velocity can be, in principle, extracted. In spite of these potentials, there are still several open issues about microwave weather radar capabilities to detect and quantitatively retrieve ash cloud parameters. A major issue is related to the aggregation of volcanic ash particles within the eruption column of explosive eruptions which has been observed at many volcanoes. It influences the residence time of ash in the atmosphere and the radiative properties of the "umbrella" cloud. Numerical experiments are helpful to explore processes occurring in the eruption column. In this study we use the plume model ATHAM (Active Tracer High Resolution Atmospheric Model) to investigate, in both time and space, processes leading to particle aggregation in the eruption column. In this work a set of numerical simulations of radar reflectivity is performed with the ATHAM model, under the same experimental conditions except for the initial size distribution, i.e. varying the radii of average mass of the two particle dimension modes. A sensitivity analysis is carried out to evaluate the possible impact of aggregate particles on microwave radar reflectivity. It is shown how dimension, composition, temperature and mass concentration are the main characteristics of eruptive cloud particles that contribute to determine different radar reflectivity responses. In order to evaluate Rayleigh scattering approximation accuracy, the ATHAM simulations of radar reflectivity are used to compare in a detailed way the Mie and Rayleigh scattering regimes at S-, C- and X-band. The relationship between radar reflectivity factor and ash concentration has been statistically derived for the various particle classes by applying a new radar reflectivity microphysical model, which was developed starting from results of numerical experiments performed with plume model ATHAM. The ash retrieval physical-statistical algorithm is based on the backscattering microphysical model of volcanic cloud particles, used within a Bayesian classification and optimal regression algorithm. In order to illustrate the potential of this microwave active remote sensing technique, the case study of the eruption of Augustine volcano in Alaska in January 2006 is described. This event was the first time that a significant volcanic eruption was observed within the nominal range of a WSR-88D. The radar data, in conjunction with pilot reports, proved to be crucial in analyzing the height and movement of volcanic ash clouds during and immediately following each eruptive event. This data greatly aided National Weather Service meteorologists in the issuance of timely and accurate warning and advisory products to aviation, public, and marine interests. An application of the retrieval technique has been shown, taking into consideration the eruption of the Augustine volcano. Volume scan data from the NEXRAD WSR-88D S-band radar, which are located 190 km from the volcano vent, are processed to identify and estimate the particles concentration in an automatic fashion. The evolution of the Augustine Vulcanian eruption is discussed in terms of radar measurements products, pointing out the unique features, the current limitations and future improvements of radar remote sensing of volcanic plumes.

Nutritional and defensive chemistry of three North American ash species: possible roles in host performance and preference by emerald ash borer

Treesearch

Yigen Chen; Therese M. Poland

2010-01-01

Black ash (Fraxinus nigra), green ash (F. pennsylvanica), and white ash (F. americana) are the three most abundant ash species in the northeastern USA. We compared emerald ash borer (EAB), Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), adult performance and preference among seedlings...

Environmental light color affects the stress response of Nile tilapia.

PubMed

Maia, Caroline Marques; Volpato, Gilson Luiz

2013-02-01

We investigated the effects of environmental light colors (blue, yellow and white) on the stress responses (measured by changes in ventilatory frequency - VF) of Nile tilapia to confinement. After 7 days of light treatment, the VF was similar for fish in each color. On the 8th day, fish were confined for 15 min. After release, the post-confinement VF was measured six times (first period: 0, 2 and 4 min; second period: 6, 8 and 10 min). Irrespective of the light color treatment, confinement increased the VF to higher levels during the first post-confinement period than during the second one. When color was analyzed, irrespective of time, fish under white light increased their VF post-confinement, and blue light prevented this effect. We conclude that blue light is the preferred color for Nile tilapia in terms of reducing stress. This finding is in contrast to previous choice test studies that indicated that yellow is their preferred color. Copyright © 2012 Elsevier GmbH. All rights reserved.

Engineering Behavior and Characteristics of Wood Ash and Sugarcane Bagasse Ash

PubMed Central

Grau, Francisco; Choo, Hyunwook; Hu, Jong Wan; Jung, Jongwon

2015-01-01

Biomasses are organic materials that are derived from any living or recently-living structure. Plenty of biomasses are produced nationwide. Biomasses are mostly combusted and usually discarded or disposed of without treatment as biomass ashes, which include wood and sugarcane bagasse ashes. Thus, recycling or treatment of biomass ashes leads to utilizing the natural materials as an economical and environmental alternative. This study is intended to provide an environmental solution for uncontrolled disposal of biomass ashes by way of recycling the biomass ash and replacing the soils in geotechnical engineering projects. Therefore, in this study, characteristic tests of wood and sugarcane bagasse ashes that are considered the most common biomass ashes are conducted. The test of chemical compositions of biomass ashes is conducted using energy dispersive X-ray spectroscopy (EDS), and Scanning Electron Microscope (SEM), and heavy metal analysis is also conducted. Engineering behaviors including hydraulic conductivity, constrained modulus and shear modulus are examined. Also, coal fly ash Class C is used in this study for comparison with biomass ashes, and Ottawa 20/30 sands containing biomass ashes are examined to identify the soil replacement effect of biomass ashes. The results show that the particle sizes of biomass ashes are halfway between coal fly ash Class C and Ottawa 20/30 sand, and biomass ashes consist of a heterogeneous mixture of different particle sizes and shapes. Also, all heavy metal concentrations were found to be below the US Environmental Protection Agency (EPA) maximum limit. Hydraulic conductivity values of Ottawa 20/30 sand decrease significantly when replacing them with only 1%–2% of biomass ashes. While both the constrained modulus and shear modulus of biomass ashes are lower than Ottawa 20/30 sand, those of mixtures containing up to 10% biomass ashes are little affected by replacing the soils with biomass ashes. PMID:28793611

CO.sub.2 utilization in electrochemical systems

DOEpatents

Boxley, Chett; Akash, Akash; Zhao, Qiang

2013-01-22

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

Parameterizing Aggregation Rates: Results of cold temperature ice-ash hydrometeor experiments

NASA Astrophysics Data System (ADS)

Courtland, L. M.; Dufek, J.; Mendez, J. S.; McAdams, J.

2014-12-01

Recent advances in the study of tephra aggregation have indicated that (i) far-field effects of tephra sedimentation are not adequately resolved without accounting for aggregation processes that preferentially remove the fine ash fraction of volcanic ejecta from the atmosphere as constituent pieces of larger particles, and (ii) the environmental conditions (e.g. humidity, temperature) prevalent in volcanic plumes may significantly alter the types of aggregation processes at work in different regions of the volcanic plume. The current research extends these findings to explore the role of ice-ash hydrometeor aggregation in various plume environments. Laboratory experiments utilizing an ice nucleation chamber allow us to parameterize tephra aggregation rates under the cold (0 to -50 C) conditions prevalent in the upper regions of volcanic plumes. We consider the interaction of ice-coated tephra of variable thickness grown in a controlled environment. The ice-ash hydrometers interact collisionally and the interaction is recorded by a number of instruments, including high speed video to determine if aggregation occurs. The electric charge on individual particles is examined before and after collision to examine the role of electrostatics in the aggregation process and to examine the charge exchange process. We are able to examine how sticking efficiency is related to both the relative abundance of ice on a particle as well as to the magnitude of the charge carried by the hydrometeor. We here present preliminary results of these experiments, the first to constrain aggregation efficiency of ice-ash hydrometeors, a parameter that will allow tephra dispersion models to use near-real-time meteorological data to better forecast particle residence time in the atmosphere.

A new natural hazards data-base for volcanic ash and SO2 from global satellite remote sensing measurements

NASA Astrophysics Data System (ADS)

Prata, F.; Stebel, K.

2013-12-01

Over the last few years there has been a recognition of the utility of satellite measurements to identify and track volcanic emissions that present a natural hazard to human populations. Mitigation of the volcanic hazard to life and the environment requires understanding of the properties of volcanic emissions, identifying the hazard in near real-time and being able to provide timely and accurate forecasts to affected areas. Amongst the many ways to measure volcanic emissions, satellite remote sensing is capable of providing global quantitative retrievals of important microphysical parameters such as ash mass loading, ash particle effective radius, infrared optical depth, SO2 partial and total column abundance, plume altitude, aerosol optical depth and aerosol absorbing index. The eruption of Eyjafjallajokull in April-May, 2010 led to increased research and measurement programs to better characterize properties of volcanic ash and the need to establish a data-base in which to store and access these data was confirmed. The European Space Agency (ESA) has recognized the importance of having a quality controlled data-base of satellite retrievals and has funded an activity (VAST) to develop novel remote sensing retrieval schemes and a data-base, initially focused on several recent hazardous volcanic eruptions. As a first step, satellite retrievals for the eruptions of Eyjafjallajokull, Grimsvotn, Puyhue-Cordon Caulle, Nabro, Merapi, Okmok, Kasatochi and Sarychev Peak are being considered. Here we describe the data, retrievals and methods being developed for the data-base. Three important applications of the data-base are illustrated related to the ash/aviation problem, to the impact of the Merapi volcanic eruption on the local population, and to estimate SO2 fluxes from active volcanoes-as a means to diagnose future unrest. Dispersion model simulations are also being included in the data-base. In time, data from conventional in situ sampling instruments, airborne and ground-based remote sensing platforms and other meta-data (bulk ash and gas properties, volcanic setting, volcanic eruption chronologies, hazards and impacts etc.) will be added. The data-base has the potential to provide the natural hazards community with the first dynamic atmospheric volcanic hazards map and will be a valuable tool particularly for global transport.

Rare earth elements in fly ashes created during the coal burning process in certain coal-fired power plants operating in Poland - Upper Silesian Industrial Region.

PubMed

Smolka-Danielowska, Danuta

2010-11-01

The subject of the study covered volatile ashes created during hard coal burning process in ash furnaces, in power plants operating in the Upper Silesian Industrial Region, Southern Poland. Coal-fired power plants are furnished with dust extracting devices, electro precipitators, with 99-99.6% combustion gas extracting efficiency. Activity concentrations ofTh-232, Ra-226, K-40, Ac-228, U-235 and U-238 were measured with gamma-ray spectrometer. Concentrations of selected rare soil elements (La, Ce, Nd, Sm, Y, Gd, Th, U) were analysed by means of instrumental neutron activation analysis (INAA). Mineral phases of individual ash particles were identified with the use of scanning electron microscope equipped with EDS attachment. Laser granulometric analyses were executed with the use of Analyssette analyser. The activity of the investigated fly-ash samples is several times higher than that of the bituminous coal samples; in the coal, the activities are: 226Ra - 85.4 Bq kg(-1), 40 K-689 Bq kg(-1), 232Th - 100.8 Bq kg(-1), 235U-13.5 Bq kg(-1), 238U-50 Bq kg(-1) and 228Ac - 82.4 Bq kg(-1).

Experimental Investigation on Pore Structure Characterization of Concrete Exposed to Water and Chlorides

PubMed Central

Liu, Jun; Tang, Kaifeng; Qiu, Qiwen; Pan, Dong; Lei, Zongru; Xing, Feng

2014-01-01

In this paper, the pore structure characterization of concrete exposed to deionised water and 5% NaCl solution was evaluated using mercury intrusion porosity (MIP), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The effects of calcium leaching, fly ash incorporation, and chloride ions on the evolution of pore structure characteristics were investigated. The results demonstrate that: (i) in ordinary concrete without any fly ash, the leaching effect of the cement products is more evident than the cement hydration effect. From the experimental data, Ca(OH)2 is leached considerably with the increase in immersion time. The pore structure of concrete can also be affected by the formation of an oriented structure of water in concrete materials; (ii) incorporation of fly ash makes a difference for the performance of concrete submersed in solutions as the total porosity and the pore connectivity can be lower. Especially when the dosage of fly ash is up to 30%, the pores with the diameter of larger than 100 nm show significant decrease. It demonstrates that the pore properties are improved by fly ash, which enhances the resistance against the calcium leaching; (iii) chlorides have a significant impact on microstructure of concrete materials because of the chemical interactions between the chlorides and cement hydrates. PMID:28788204

Climate change and the ash dieback crisis

PubMed Central

Goberville, Eric; Hautekèete, Nina-Coralie; Kirby, Richard R.; Piquot, Yves; Luczak, Christophe; Beaugrand, Grégory

2016-01-01

Beyond the direct influence of climate change on species distribution and phenology, indirect effects may also arise from perturbations in species interactions. Infectious diseases are strong biotic forces that can precipitate population declines and lead to biodiversity loss. It has been shown in forest ecosystems worldwide that at least 10% of trees are vulnerable to extinction and pathogens are increasingly implicated. In Europe, the emerging ash dieback disease caused by the fungus Hymenoscyphus fraxineus, commonly called Chalara fraxinea, is causing a severe mortality of common ash trees (Fraxinus excelsior); this is raising concerns for the persistence of this widespread tree, which is both a key component of forest ecosystems and economically important for timber production. Here, we show how the pathogen and climate change may interact to affect the future spatial distribution of the common ash. Using two presence-only models, seven General Circulation Models and four emission scenarios, we show that climate change, by affecting the host and the pathogen separately, may uncouple their spatial distribution to create a mismatch in species interaction and so a lowering of disease transmission. Consequently, as climate change expands the ranges of both species polewards it may alleviate the ash dieback crisis in southern and occidental regions at the same time. PMID:27739483

A Bilateral U.S. - Russia Contribution to Disaster Risk Reduction in the Asia-Pacific Region

NASA Astrophysics Data System (ADS)

Eichelberger, J. C.; Gordeev, E.; Bratton, J.; Ismail-Zadeh, A.

2012-12-01

An accepted principle of disaster risk reduction is that all stakeholders should be engaged in the process. For extreme geophysical events, this almost always means stakeholders in more than one country. Even when the direct impacts on the ground from violent shaking or explosive eruptions are confined to a single country, effects to lives and property may be carried thousands of kilometers from the event source by tsunamis or ash clouds, respectively. The formation of G-EVER recognizes the need for neighbors to join together on disaster risk reduction. There is much to be gained by sharing real-time monitoring data and databases on past extreme events, mapping risks seamlessly across borders, and establishing best practices through sharing of experiences. Each extreme event is a learning opportunity, and the recent lessons have been particularly painful. Our science, while progressing, is still inadequate both in content and in application. There has also been lack of recognition that the "worst case" is indeed possible. Among the various collaborations needed to reduce disaster risk is bilateral collaboration, because borders are obstacles and exist between two countries with rules that have been determined by those countries. Borders are used by all countries for protection of national and economic security. They restrict flow of people, equipment, and information, but not seismic waves, tsunamis, and ash. Even the relatively minor event of sea ice arriving early in Nome, Alaska last fall involved both Russia and the U.S. in a relief effort to bring fuel. It is the responsibility of natural hazard scientists and crisis managers to work together across borders, and where necessary make the case to their governments for sharing of data and information based on an expanded view of national security. The Bilateral Presidential Commission initiated by U.S. President Barrack Obama and Russian President Dmitry Medvedev has provided a framework in which to expand collaboration in dealing with the geohazards of the Russian Far East - Alaska region. Subduction within this segment of the Pacific Rim has produced 50% of the top 30 earthquakes recorded instrumentally worldwide, numerous Pacific-crossing tsunamis, and the largest ash eruption in almost 200 years. Recognizing that Russia and the United States need to develop a whole-region perspective of disaster risk, scientists and program managers from several Russian and U.S. government agencies met at the Russian Academy of Sciences in Moscow in July to identify bilateral steps that would improve safety for communities of the Kuril-Kamchatka-Aleutian-Alaska region. Significantly, the meeting included disaster preparation and response agencies EMERCOM and FEMA. Participants proposed development of a standing committee to advocate and facilitate bilateral collaboration, expanded exchange of real-time monitoring data, development of a strategy for monitoring currently unmonitored sections of plate and micro-plate boundaries, and holding of an inclusive, all-stakeholders meeting in the U.S. next year.

Interspecific proteomic comparisons reveal ash phloem genes potentially involved in constitutive resistance to the emerald ash borer

Treesearch

Justin G.A. Whitehill; Alexandra Popova-Butler; Kari B. Green-Church; Jennifer L. Koch; Daniel A. Herms; Pierluigi Bonello

2011-01-01

The emerald ash borer (Agrilus planipennis) is an invasive wood-boring beetle that has killed millions of ash trees since its accidental introduction to North America. All North American ash species (Fraxinus spp.) that emerald ash borer has encountered so far are susceptible, while an Asian species, Manchurian ash (F....

Source mass eruption rate retrieved from satellite-based data using statistical modelling

NASA Astrophysics Data System (ADS)

Gouhier, Mathieu; Guillin, Arnaud; Azzaoui, Nourddine; Eychenne, Julia; Valade, Sébastien

2015-04-01

Ash clouds emitted during volcanic eruptions have long been recognized as a major hazard likely to have dramatic consequences on aircrafts, environment and people. Thus, the International Civil Aviation Organization (ICAO) established nine Volcanic Ash Advisory Centers (VAACs) around the world, whose mission is to forecast the location and concentration of ash clouds over hours to days, using volcanic ash transport and dispersion models (VATDs). Those models use input parameters such as plume height (PH), particle size distribution (PSD), and mass eruption rate (MER), the latter being a key parameter as it directly controls the amount of ash injected into the atmosphere. The MER can be obtained rather accurately from detailed ground deposit studies, but this method does not match the operational requirements in case of a volcanic crisis. Thus, VAACs use empirical laws to determine the MER from the estimation of the plume height. In some cases, this method can be difficult to apply, either because plume height data are not available or because uncertainties related to this method are too large. We propose here an alternative method based on the utilization of satellite data to assess the MER at the source, during explosive eruptions. Satellite-based techniques allow fine ash cloud loading to be quantitatively retrieved far from the source vent. Those measurements can be carried out in a systematic and real-time fashion using geostationary satellite, in particular. We tested here the relationship likely to exist between the amount of fine ash dispersed in the atmosphere and of coarser tephra deposited on the ground. The sum of both contributions yielding an estimate of the MER. For this purpose we examined 19 eruptions (of known duration) in detail for which both (i) the amount of fine ash dispersed in the atmosphere, and (ii) the mass of tephra deposited on the ground have been estimated and published. We combined these data with contextual information that may influence the statistical relationship such as the magma composition or the existence of phreatomagmatism. In order to infer the relationship between ash content in the atmosphere and the amount of tephra on the ground, we used advanced statistic modelling using model selection, with AIC-type (Akaike Information Criterion) penalization, and classification. First we show that a reliable statistical relationship does exist between atmospheric fine ash and tephra fall deposits. Then we show that magma composition does have an effect on this relationship. It follows a power function in the form S_1=c_0{S_2}c_1(P_n))Hc_2 having a coefficient of determination r2=0.91 and a prediction error of 2.16 at a confidence level of 95%. S1 is the mass of tephra fall deposits and S2 is the fine ash cloud mass as retrieved from satellite measurements. H is the plume height, c0 and c2 are constant coefficients while c1 is variable and depends on the magma composition type (Pn=1:3). This method greatly improves the prediction capability of the source MER as compared to the one based on the plume height solely. If available in real-time, satellite data might be advantageously used as a proxy by the VAACs, to derive key source parameters such as the MER.

Volcanic ash deposition, eelgrass beds, and inshore habitat loss from the 1920s to the 1990s at Chignik, Alaska

NASA Astrophysics Data System (ADS)

Zimmermann, Mark; Ruggerone, Gregory T.; Freymueller, Jeffrey T.; Kinsman, Nicole; Ward, David H.; Hogrefe, Kyle R.

2018-03-01

We quantified the shallowing of the seafloor in five of six bays examined in the Chignik region of the Alaska Peninsula, confirming National Ocean Service observations that 1990s hydrographic surveys were shallower than previous surveys from the 1920s. Castle Bay, Chignik Lagoon, Hook Bay, Kujulik Bay and Mud Bay lost volume as calculated from Mean Lower Low Water (Chart Datum) to the deepest depths and four of these sites lost volume from Mean High Water to the deepest depths. Calculations relative to each datum were made because tidal datum records exhibited an increase in tidal range in this region from the 1920s to the 1990s. Our analysis showed that Mud Bay is quickly disappearing while Chignik Lagoon is being reduced to narrow channels. Anchorage Bay was the only site that increased in depth over time, perhaps due to erosion. Volcanoes dominate the landscape of the Chignik area. They have blanketed the region in deep ash deposits before the time frame of this study, and some have had smaller ash-producing eruptions during the time frame of this study. Remobilization of land-deposited ash and redeposition in marine areas - in some locations facilitated by extensive eelgrass (Zostera marina) beds (covering 54% of Chignik Lagoon and 68% of Mud Bay in 2010) - is the most likely cause of shallowing in the marine environment. Loss of shallow water marine habitat may alter future abundance and distribution of several fish, invertebrate and avian species.

Detectability of the emerald ash borer (Coleoptera: Buprestidae) in asymptomatic urban trees by using branch samples.

PubMed

Ryall, Krista L; Fidgen, Jeffrey G; Turgeon, Jean J

2011-06-01

The emerald ash borer, Agrilus planipennis Fairmaire, is an exotic invasive insect causing extensive mortality to ash trees, Fraxinus spp., in Canada and the United States. Detection of incipient populations of this pest is difficult because of its cryptic life stages and a multiyear time lag between initial attack and the appearance of signs or symptoms of infestation. We sampled branches from open-grown urban ash trees to develop a sample unit suitable for detecting low density A. planipennis infestation before any signs or symptoms are evident. The sample unit that maximized detection rates consisted of one 50-cm-long piece from the base of a branch ≥6 cm diameter in the midcrown. The optimal sample size was two such branches per tree. This sampling method detected ≈75% of asymptomatic trees known to be infested by using more intensive sampling and ≈3 times more trees than sampling one-fourth of the circumference of the trunk at breast height. The method is less conspicuous and esthetically damaging to a tree than the removal of bark from the main stem or the use of trap trees, and could be incorporated into routine sanitation or maintenance of city-owned trees to identify and delineate infested areas. This research indicates that branch sampling greatly reduces false negatives associated with visual surveys and window sampling at breast height. Detection of A. planipennis-infested asymptomatic trees through branch sampling in urban centers would provide landowners and urban foresters with more time to develop and implement management tactics.

Proximate nutrient analyses of four species of submerged aquatic vegetation consumed by Florida manatee (Trichechus manatus latirostris) compared to romaine lettuce (Lactuca sativa var. longifolia).

PubMed

Siegal-Willott, Jessica L; Harr, Kendal; Hayek, Lee-Ann C; Scott, Karen C; Gerlach, Trevor; Sirois, Paul; Reuter, Mike; Crewz, David W; Hill, Richard C

2010-12-01

Free-ranging Florida manatees (Trichechus manatus latirostris) consume a variety of sea grasses and algae. This study compared the dry matter (DM) content, proximate nutrients (crude protein [CP], ether-extracted crude fat [EE], nonfiber carbohydrate [NFC], and ash), and the calculated digestible energy (DE) of sea grasses (Thalassia testudinum, Halodule wrightii, and Syringodium filiforme) collected in spring, summer, and winter, and an alga (Chara sp.) with those of romaine lettuce (Lactuca sativa var. longifolia). Neutral-detergent fiber (NDF), acid-detergent fiber (ADF), and lignin (L) measured after ash-extraction were also compared. Results of statistical tests (C = 0.01) revealed DM content was higher in aquatic vegetation than in lettuce (P = 0.0001), but NDF and ADF were up to threefold greater, EE (P = 0.00001) and CP (P = 0.00001) were 2-9 times less, and NFC (P = 0.0001) was 2-6 times lower in sea grass than in lettuce, on a DM basis. Chara was lower in NDF, ADF, L, EE, CP, and NFC relative to lettuce on a DM basis. Ash content (DM basis) was higher (P = 0.0001), and DE was 2-6 times lower in aquatic vegetation than in lettuce. Sea grass rhizomes had lower L and higher ash contents (DM basis) than sea grass leaves. Based on the nutrient analyses, romaine lettuce and sea grasses are not equivalent forages, which suggests that the current diet of captive Florida manatees should be reassessed.

Factorial experimental design application in modification of volcanic ash as a natural adsorbent with Fenton process for arsenic removal.

PubMed

Jaafarzadeh, Neamat; Amiri, Hoda; Ahmadi, Mehdi

2012-01-01

This paper describes an experimental design technique for the modification of volcanic ash with Fenton reagent (FMVA) to be used as a natural adsorbent in the removal of As(III) and As(V) from aqueous solution. The influence of pH, contact time and Fe(2+)/H2O2 on arsenic removal by the modified volcanic ash was investigated. It was observed that the arsenic removal efficiency was influenced by two of these parameters. The Fe(2+)/H2O2 ratio is an important factor that affects both As(III) and As(V) adsorption (P = 0.000). The pH affects As(V) adsorption (P = 0.003) more significantly than As (III) adsorption (P = 0.02). It was observed that the maximum As(III) adsorption by the FMVA was obtained at pH 2, Fe(+2)/H2O2 = 0.06 and 30 min of contact time (39 microg As(III) per mg FMVA), whereas the maximum As(V) adsorption was obtained under the conditions of pH 5, Fe(+2)/H2O2 = 0.06 and 30 min of contact time (41 microg As(V) per mg FMVA).

Volcanic Cyclicities in the Pacific Northwest: Insights from the Marine Tephra Record from IODP Expedition 350, Izu Bonin Arc

NASA Astrophysics Data System (ADS)

Straub, S. M.; Schindlbeck, J. C.; Jegen, M. D.; Corry-Saavedra, K.; Murayama, M.; Woodhead, J. D.; Kutterolf, S.; Vautravers, M. J.; Wang, K. L.

2016-12-01

While the influences of orbital cycles on the ocean-atmosphere system are well documented, it remains largely unknown whether Earth's interior processes are similarly connected to orbital cycles. Recent studies of cyclic deposition in ash fallout from arc volcanism suggest that global climate changes in the form of variable glacial and water load are inversely related to magma production and/or volcanic eruption rate. However, a rigorous test of this hypotheses requires a temporally precise record of past volcanism which spans multiple glacial cycles at high resolution. The marine ash record of explosive volcanism provides such records readily. Here we undertake a detailed chemical study of discrete and disperse tephra deposits in cores from IODP Holes U1437B and U1436A drilled near the Izu Bonin arc in the northwestern Pacific. These locations combine a high background sedimentation rate (>10 m/Ma) of biogenic carbonate and Asian-derived dust with frequent emplacement of tephra fallout from the nearby Izu Bonin and Japan arcs. δ18O analyses record thirteen climatic cycles in the carbonate mud of the uppermost 120 m of Hole U1437B and eleven cycles in the uppermost 70 m of Hole U1436C. Strikingly, the distribution of 134 primary ash layers in Hole U1437B seems to be synchronous with glacial cycles, with a distinct increase in eruption occurrences at either the transitions of glacial/interglacial or at the early interglacials. This is confirmed by first results of a frequency analysis of the ash-time series that indicate a dominance of a 100 ka cycle. The question, which remains to be answered, is whether deglaciation drives volcanism or volcanism drives deglaciation? We also investigate the distribution of `dispersed ash' in this sequence, which is not visible to the naked eye but is volumetrically significant and thus also critical in testing time-cause relationships between arc volcanism and glacial cycles. Major questions we address are: 1) do we see the same cyclic behavior between dispersed ash and discrete ash layers?, 2) does this cyclicity following orbital cycles and 3) is the distribution of tephra layers controlled by orbital cycles or do the tephras reflect the cyclic deposition of the host sediment?

Removal of Cr6 + and Ni2+ from aqueous solution using bagasse and fly ash.

PubMed

Rao, M; Parwate, A V; Bhole, A G

2002-01-01

Raw bagasse and fly ash, the waste generated in sugar mills and boilers respectively have been used as low-cost potential adsorbents. Raw bagasse was pretreated with 0.1N NaOH followed by 0.1N CH3COOH before its application. These low-cost adsorbents were used for the removal of chromium and nickel from an aqueous solution. The kinetics of adsorption and extent of adsorption at equilibrium are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental system. The effect of hydrogen ion concentration, contact time, sorbent dose, initial concentrations of adsorbate and adsorbent and particle size on the uptake of chromium and nickel were studied in batch experiments. The Sorption data has been correlated with Langmuir, Freundlich and Bhattacharya and Venkobachar adsorption models. The efficiencies of adsorbent materials for the removal of Cr(VI) and Ni(II) were found to be between 56.2 and 96.2% and 83.6 and 100%, respectively. These results were obtained at the optimized conditions of pH, contact time, sorbent dose, sorbate concentration of 100 mg/l and with the variation of adsorbent particles size between 0.075 and 4.75 mm. The order of selectivity is powdered activated carbon > bagasse > fly ash for Cr(VI) removal and powdered activated carbon > fly ash > bagasse for Ni(II) removal.

Influence of bacteria on lanthanide and actinide transfer from specific soil components (humus, soil minerals and vitrified municipal solid waste incinerator bottom ash) to corn plants: Sr-Nd isotope evidence.

PubMed

Aouad, Georges; Stille, Peter; Crovisier, Jean-Louis; Geoffroy, Valérie A; Meyer, Jean-Marie; Lahd-Geagea, Majdi

2006-11-01

Experiments have been performed to test the stability of vitrified municipal solid waste (MSW) incinerator bottom ash under the presence of bacteria (Pseudomonas aeruginosa) and plants (corn). The substratum used for the plant growth was a humus-rich soil mixed with vitrified waste. For the first time, information on the stability of waste glasses in the presence of bacteria and plants is given. Results show that inoculated plant samples contained always about two times higher lanthanide and actinide element concentrations. Bacteria support the element transfer since plants growing in inoculated environment developed a smaller root system but have higher trace element concentrations. Compared with the substratum, plants are light rare earth element (LREE) enriched. The vitrified bottom ash has to some extent been corroded by bacteria and plant activities as indicated by the presence of Nd (REE) and Sr from the vitrified waste in the plants. (87)Sr/(86)Sr and (143)Nd/(144)Nd isotope ratios of plants and soil components allow the identification of the corroded soil components and confirm that bacteria accelerate the assimilation of elements from the vitrified bottom ash. These findings are of importance for landfill disposal scenarios, and similar experiments should be performed in order to better constrain the processes of microbially mediated alteration of the MSW glasses in the biosphere.

[Effect of sodium carbonate assisted hydrothermal process on heavy metals stabilization in medical waste incinerator fly ash].

PubMed

Jin, Jian; Li, Xiao-dong; Chi, Yong; Yan, Jian-hua

2010-04-01

A sodium carbonate assisted hydrothermal process was induced to stabilize the fly ash from medical waste incinerator. The results showed that sodium carbonate assisted hydrothermal process reduced the heavy metals leachability of fly ash, and the heavy metal waste water from the process would not be a secondary pollution. The leachability of heavy metals studied in this paper were Cd 1.97 mg/L, Cr 1.56 mg/L, Cu 2.56 mg/L, Mn 17.30 mg/L, Ni 1.65 mg/L, Pb 1.56 mg/L and Zn 189.00 mg/L, and after hydrothermal process with the optimal experimental condition (Na2CO3/fly ash dosage = 5/20, reaction time = 8 h, L/S ratio = 10/1) the leachability reduced to < 0.02 mg/L for Cd, Cr, Cu, Mn, Ni, Pb, and 0.05 mg/L for Zn, according to GB 5085.3-2007. Meanwhile, the concentrations of heavy metals in effluent after hydrothermal process were less than 0.8 mg/L. The heavy metals leachability and concentration in effluent reduced with prolonged reaction time. Prolonged aging can affect the leachability of metals as solids become more crystalline, and heavy metals transferred inside of crystalline. The mechanism of heavy metal stabilization can be concluded to the co precipitation and adsorption effect of aluminosilicates formation, crystallization and aging process.

A model for inferring transport rates from observed confinement times in field-reversed configurations

NASA Astrophysics Data System (ADS)

Steinhauer, Loren C.; Milroy, Richard D.; Slough, John T.

1985-03-01

A one-dimensional transport model is developed to simulate the confinement of plasma and magnetic flux in a field-reversed configuration. Given the resistivity, the confinement times can be calculated. Approximate expressions are found which yield the magnitude and gross profile of the resistivity if the confinement times are known. These results are applied to experimental data from experiments, primarily TRX-1, to uncover trends in the transport properties. Several important conclusions emerge. The transport depends profoundly, and inexplicably, on the plasma formation mode. The inferred transport differs in several ways from the predictions of local lower-hybrid-drift turbulence theory. Finally, the gross resistivity exhibits an unusual trend with xs (separatrix radius rs divided by the conducting wall radius rc ), and is peaked near the magnetic axis for certain predictable conditions.

Chemical composition and properties of ashes from combustion plants using Miscanthus as fuel.

PubMed

Lanzerstorfer, Christof

2017-04-01

Miscanthus giganteus is one of the energy crops considered to show potential for a substantial contribution to sustainable energy production. In the literature there is little data available about the chemical composition of ashes from the combustion of Miscanthus and practically no data about their physical properties. However, for handling, treatment and utilization of the ashes this information is important. In this study ashes from two biomass combustion plants using Miscanthus as fuel were investigated. The density of the ashes was 2230±35kg/m 3 , which was similar to the density of ashes from straw combustion. Also the bulk densities were close to those reported for straw ashes. The flowability of the ashes was a little worse than the flowability of ashes from wood combustion. The measured heavy metal concentrations were below the usual limits for utilization of the ashes as soil conditioner. The concentrations in the bottom ash were similar to those reported for ash from forest residue combustion plants. In comparison with cyclone fly ashes from forest residue combustion the measured heavy metal concentrations in the cyclone fly ash were considerably lower. Cl - , S and Zn were enriched in the cyclone fly ash which is also known for ashes from wood combustion. In comparison with literature data obtained from Miscanthus plant material the concentrations of K, Cl - and S were lower. This can be attributed to the fact that the finest fly ash is not collected by the cyclone de-dusting system of the Miscanthus combustion plants. Copyright © 2016. Published by Elsevier B.V.

Buckets of ash track tephra flux from Halema'uma'u Crater, Hawai'i

USGS Publications Warehouse

Swanson, Don; Wooten, Kelly M.; Orr, Tim R.

2009-01-01

The 2008–2009 eruption at Kīlauea Volcano's summit made news because of its eight small discrete explosive eruptions and noxious volcanic smog (vog) created from outgassing sulfur dioxide. Less appreciated is the ongoing, weak, but continuous output of tephra, primarily ash, from the new open vent in Halema'uma'u Crater. This tephra holds clues to processes causing the eruption and forming the new crater-in-a-crater, and its flux is important to hazard evaluations.The setting of the vent–easily accessible from the Hawaiian Volcano Observatory (HVO)—is unusually favorable for neardaily tracking of tephra mass flux during this small prolonged basaltic eruption. Recognizing this, scientists from HVO are collecting ash and documenting how ejection masses, components, and chemical compositions vary through time.

Fungus-Mediated Preferential Bioleaching of Waste Material Such as Fly - Ash as a Means of Producing Extracellular, Protein Capped, Fluorescent and Water Soluble Silica Nanoparticles

PubMed Central

Khan, Shadab Ali; Uddin, Imran; Moeez, Sana; Ahmad, Absar

2014-01-01

In this paper, we for the first time show the ability of the mesophilic fungus Fusarium oxysporum in the bioleaching of waste material such as Fly-ash for the extracellular production of highly crystalline and highly stable, protein capped, fluorescent and water soluble silica nanoparticles at ambient conditions. When the fungus Fusarium oxysporum is exposed to Fly-ash, it is capable of selectively leaching out silica nanoparticles of quasi-spherical morphology within 24 h of reaction. These silica nanoparticles have been completely characterized by UV-vis spectroscopy, Photoluminescence (PL), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Energy dispersive analysis of X-rays (EDAX). PMID:25244567

Ash Analysis

NASA Astrophysics Data System (ADS)

Marshall, Maurice R.

Ash refers to the inorganic residue remaining after either ignition or complete oxidation of organic matter in a foodstuff. A basic knowledge of the characteristics of various ashing procedures and types of equipment is essential to ensure reliable results. Two major types of ashing are used: dry ashing, primarily for proximate composition and for some types of specific mineral analyses; wet ashing (oxidation), as a preparation for the analysis of certain minerals. Microwave systems now are available for both dry and wet ashing, to speed the processes. Most dry samples (i.e., whole grain, cereals, dried vegetables) need no preparation, while fresh vegetables need to be dried prior to ashing. High-fat products such as meats may need to be dried and fat extracted before ashing. The ash content of foods can be expressed on either a wet weight (as is) or on a dry weight basis. For general and food-specific information on measuring ash content, see references (1-11).

Study of the confinement properties in a reversed-field pinch with mode rotation and gas fuelling

NASA Astrophysics Data System (ADS)

Cecconello, M.; Malmberg, J.-A.; Nielsen, P.; Pasqualotto, R.; Drake, J. R.

2002-08-01

An extensive investigation of the global confinement properties in different operating scenarios in the rebuilt EXTRAP T2R reversed-field pinch (RFP) experiment is reported here. In particular, the role of a fast gas puff valve system, used to control plasma density, on confinement is studied. Without gas puffing, the electron density decays below 0.5×1019 m-3. The poloidal beta varies between 5% and 15%, decreasing at large I/N. The energy confinement time ranges from 70 to 225 μs. With gas puffing, the density is sustained at ne≈1.5×1019 m-3. However, a general slight deterioration of the plasma performances is observed for the same values of I/N: the plasma becomes cooler and more radiative. The poloidal beta is comparable to that in the scenarios without puff but the energy confinement time drops ranging from 60 to 130 μs. The fluctuation level and the energy confinement time have been found to scale with the Lundquist number as S-0.05+/-0.07 and S0.5+/-0.1, respectively. Mode rotation is typical for all the discharges and rotation velocity is observed to increase with increasing electron diamagnetic velocity.

Role of density modulation in the spatially resolved dynamics of strongly confined liquids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saw, Shibu, E-mail: shibu.saw@sydney.edu.au; Dasgupta, Chandan, E-mail: cdgupta@physics.iisc.ernet.in

Confinement by walls usually produces a strong modulation in the density of dense liquids near the walls. Using molecular dynamics simulations, we examine the effects of the density modulation on the spatially resolved dynamics of a liquid confined between two parallel walls, using a resolution of a fraction of the interparticle distance in the liquid. The local dynamics is quantified by the relaxation time associated with the temporal autocorrelation function of the local density. We find that this local relaxation time varies in phase with the density modulation. The amplitude of the spatial modulation of the relaxation time can bemore » quite large, depending on the characteristics of the wall and thermodynamic parameters of the liquid. To disentangle the effects of confinement and density modulation on the spatially resolved dynamics, we compare the dynamics of a confined liquid with that of an unconfined one in which a similar density modulation is induced by an external potential. We find several differences indicating that density modulation alone cannot account for all the features seen in the spatially resolved dynamics of confined liquids. We also examine how the dynamics near a wall depends on the separation between the two walls and show that the features seen in our simulations persist in the limit of large wall separation.« less

Dynamics of two-dimensional monolayer water confined in hydrophobic and charged environments.

PubMed

Kumar, Pradeep; Han, Sungho

2012-09-21

We perform molecular dynamics simulations to study the effect of charged surfaces on the intermediate and long time dynamics of water in nanoconfinements. Here, we use the transferable interaction potential with five points (TIP5P) model of a water molecule confined in both hydrophobic and charged surfaces. For a single molecular layer of water between the surfaces, we find that the temperature dependence of the lateral diffusion constant of water up to very high temperatures remains Arrhenius with a high activation energy. In case of charged surfaces, however, the dynamics of water in the intermediate time regime is drastically modified presumably due to the transient coupling of dipoles of water molecules with electric field fluctuations induced by charges on the confining surfaces. Specifically, the lateral mean square displacements display a distinct super-diffusive behavior at intermediate time scale, defined as the time scale between ballistic and diffusive regimes. This change in the intermediate time-scale dynamics in the charged confinement leads to the enhancement of long-time dynamics as reflected in increasing diffusion constant. We introduce a simple model for a possible explanation of the super-diffusive behavior and find it to be in good agreement with our simulation results. Furthermore, we find that confinement and the surface polarity enhance the low frequency vibration in confinement compared to bulk water. By introducing a new effective length scale of coupling between translational and orientational motions, we find that the length scale increases with the increasing strength of the surface polarity. Further, we calculate the correlation between the diffusion constant and the excess entropy and find a disordering effect of polar surfaces on the structure of water. Finally, we find that the empirical relation between the diffusion constant and the excess entropy holds for a monolayer of water in nanoconfinement.

Proceedings of symposium on ash in North America

Treesearch

Charles H. Michler; Matthew D., eds. Ginzel

2010-01-01

Includes 5 papers and 30 abstracts covering topics related to the biology and ecology of the ash species, ash utilization and management, emerald ash borer, and other threats to ash, and genetics and conservation of ash species. A paper titled "Population-level variation of Fraxinus americana L. is influenced by climate...

40 CFR 302.6 - Notification requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... transportation of coal and coal ash (including fly ash, bottom ash, and boiler slags), including the dumping and... coal and coal ash, including fly ash, bottom ash, and boiler slags. (d) Except for releases of..., chromium, copper, lead, nickel, selenium, silver, thallium, or zinc is not required if the mean diameter of...

Fluidized bed combustion bottom ash: A better and alternative geo-material resource for construction.

PubMed

Mandal, A K; Paramkusam, Bala Ramudu; Sinha, O P

2018-04-01

Though the majority of research on fly ash has proved its worth as a construction material, the utility of bottom ash is yet questionable due to its generation during the pulverized combustion process. The bottom ash produced during the fluidized bed combustion (FBC) process is attracting more attention due to the novelty of coal combustion technology. But, to establish its suitability as construction material, it is necessary to characterize it thoroughly with respect to the geotechnical as well as mineralogical points of view. For fulfilling these objectives, the present study mainly aims at characterizing the FBC bottom ash and its comparison with pulverized coal combustion (PCC) bottom ash, collected from the same origin of coal. Suitability of FBC bottom ash as a dike filter material in contrast to PCC bottom ash in replacing traditional filter material such as sand was also studied. The suitability criteria for utilization of both bottom ash and river sand as filter material on pond ash as a base material were evaluated, and both river sand and FBC bottom ash were found to be satisfactory. The study shows that FBC bottom ash is a better geo-material than PCC bottom ash, and it could be highly recommended as an alternative suitable filter material for constructing ash dikes in place of conventional sand.

P retention and cation exchange as affected by nanoparticle of volcanic ash and application of phosphate solubilizing bacteria on Andisol Ciater, West Java, Indonesia

NASA Astrophysics Data System (ADS)

Fitriatin, Betty Natalie; Arifin, Mahfud; Devnita, Rina; Yuniarti, Anni; Haryanto, Rachmat; Setiabudi, Mariska Amalia

2018-02-01

Andisols is a soil with high retention of phosphate and cannot be absorbed by plants. Some of soil bacteria have the ability to solubilize P and make it available to growing plants are known phosphate solubilizing bacteria (PSB). The research aims to study the effect of nanoparticle volcanic ash and phosphate solubilising bacteria (PSB) on P retention and cation exchangeable (CEC) in Andisol Ciater, West Java. This research was conducted from October 2016 to March 2017. The design of the analysis used was a complete randomized factorial design with two factors. The first factor was nanoparticle volcanic ash (a) consists of four dosages based on weight percentage (0%, 2.5%, 5.0% and 7.5%) and the second factor was PSB (h) consists of two dosages (without biofertilizer and with biofertilizer 1 g/Kg soil). The combination treatments replicated three times were incubated for 4 months. Soil samples were analyzed at first month and fourth month after incubation. The results showed that all dosages of nanoparticle volcanic ash and application of PSB decreased P retention by 75-77% at the first month after incubation. Nanoparticle volcanic ash dosage decreased to 7.5% the P retention reaches 90.36% in the fourth month after incubation. The nanoparticle of volcanic ash dosage 7.5% increased with CEC (24.787 cmol.kg-1 and 16.555 cmol.kg-1) at the first and fourth months after incubation. The application of PSB increased the CEC (28.606 cmol.kg-1) in the first month after incubation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, Tyler F; Jett, Robert Trent; Smith, John G.

A dike failure at the Tennessee Valley Authority Kingston Fossil Plant in East Tennessee, United States, in December 2008, released approximately 4.1 million m3 of coal ash into the Emory River. From 2009 through 2012, samples of mayfly nymphs ( Hexagenia bilineata) were collected each spring from sites in the Emory, Clinch, and Tennessee Rivers upstream and downstream of the spill. Samples were analyzed for 17 metals. Concentrations of metals were generally highest the first 2 miles downstream of the spill, and then decreased with increasing distance from the spill. Arsenic, B, Ba, Be, Mo, Sb, Se, Sr, and Vmore » appeared to have strong ash signatures, whereas Co, Cr, Cu, Ni, and Pb appeared to be associated with ash and other sources. Furthermore, the concentrations for most of these contaminants were modest and are unlikely to cause widespread negative ecological effects. Trends in Hg, Cd, and Zn suggested little (Hg) or no (Cd, Zn) association with ash. Temporal trends suggested that concentrations of ash-related contaminants began to subside after 2010, but because of the limited time period of that analysis (4 yr), further monitoring is needed to verify this trend. The present study provides important information on the magnitude of contaminant exposure to aquatic receptors from a major coal ash spill, as well as spatial and temporal trends for transport of the associated contaminants in a large open watershed. Environ Toxicol Chem 2016;35:1159 1171. Published 2015 Wiley Periodicals Inc. on behalf of SETAC. This article is a US government work and, as such, is in the public domain in the United States of America.« less

Sediment delivery after a wildfire

USGS Publications Warehouse

Reneau, Steven L.; Katzman, D.; Kuyumjian, G.A.; Lavine, A.; Malmon, D.V.

2007-01-01

We use a record of sedimentation a small reservoir within the Cerro Grande burn area, New Mexico, to document postfire delivery of ash, other fine-grained sediment carried in suspension within floods, and coarse-grained sediment transported as bedload over a five-year period. Ash content of sediment layers is estimated using fallout 137Cs as a tracer, and ash concentrations are shown to rapidly decrease through a series of moderate-intensity convective storms in the first rainy season after the fire. Over 90% of the ash was delivered to the reservoir in the first year, and ash concentrations in suspended sediment were negligible after the second year. Delivery of the remainder of the fine sediment also declined rapidly after the first year despite the occurrence of higher-intensity storms in the second year. Fine sediment loads after five years remained significantly above prefire averages. Deposition of coarse-grained sediment was irregular in time and was associated with transport by snowmelt runoff of sediment stored along the upstream channel during short-duration summer floods. Coarse sediment delivery in the first four years was strongly correlated with snowmelt volume, suggesting a transport-limited system with abundant available sediment. Transport rates of coarse sediment declined in the fifth year, consistent with a transition to a more stable channel as the accessible sediment supply was depleted and the channel bed coarsened. Maximum impacts from ash and other fine-grained sediment therefore occurred soon after the fire, whereas the downstream impacts from coarse-grained sediment were attenuated by the more gradual process of bedload sediment transport. ?? 2007 Geological Society of America.

[Characterization of PAHs in fly ashes from coke production].

PubMed

Mu, Ling; Peng, Lin; Liu, Xiao-Feng; Bai, Hui-Ling; Zhang, Jian-Qiang

2013-03-01

In order to investigate the characteristics of polycyclic aromatic hydrocarbons (PAHs) in ashes from coking, PAHs in ashes from three coke production plants were analyzed with GC-MS, and the distribution characteristics of PAHs and potential toxicity risk were discussed. The sum of 16 EPA prior PAHs varied from 8.17 x 10(2) to 5.17 x 10(3) microg x g(-1). PAH contents from the coke oven (stamp charging) with the height of 3.2 m were two times higher than those from the one (top charging) with the height of 6.0 m, and PAHs in ashes from coal charging were significantly higher than those from coke pushing in the same plant. Four-ring and five-ring PAHs were the dominant species in ashes from coking and the sum of them accounted for more than 80.00% of total PAHs. Chrysene (Chr), benzo [a] anthracene (BaA) and benzo [b] fluoranthene (BbF) were abundant in all ash samples. The content of total BaP-based toxic equivalency (BaPeq) ranged from 1.64 x 10(2) to 9.57 x 10(2) microg x g(-1). From the carcinogenic point of view, besides benzo [a] pyrene (BaP), dibenz [a,h] anthracene (DbA) contributed most to the overall toxicity of PAHs, followed by BaA and BbF. BaPeq concentration from coal charging was 5.21-fold higher than that from coke pushing, indicating that different reuse ways should be considered based on their specific toxicity profiles of PAHs.

Neural-Network Approach to Hyperspectral Data Analysis for Volcanic Ash Clouds Monitoring

NASA Astrophysics Data System (ADS)

Piscini, Alessandro; Ventress, Lucy; Carboni, Elisa; Grainger, Roy Gordon; Del Frate, Fabio

2015-11-01

In this study three artificial neural networks (ANN) were implemented in order to emulate a retrieval model and to estimate the ash Aerosol optical Depth (AOD), particle effective radius (reff) and cloud height from volcanic eruption using hyperspectral remotely sensed data. ANNs were trained using a selection of Infrared Atmospheric Sounding Interferometer (IASI) channels in Thermal Infrared (TIR) as inputs, and the corresponding ash parameters retrieved obtained using the Oxford retrievals as target outputs. The retrieval is demonstrated for the eruption of the Eyjafjallajo ̈kull volcano (Iceland) occurred in 2010. The results of validation provided root mean square error (RMSE) values between neural network outputs and targets lower than standard deviation (STD) of corresponding target outputs, therefore demonstrating the feasibility to estimate volcanic ash parameters using an ANN approach, and its importance in near real time monitoring activities, owing to its fast application. A high accuracy has been achieved for reff and cloud height estimation, while a decreasing in accuracy was obtained when applying the NN approach for AOD estimation, in particular for those values not well characterized during NN training phase.

Synthesis and adsorption properties of titanosilicates ETS-4 and ETS-10 from fly ash.

PubMed

Liu, Liying; Singh, Ranjeet; Li, Gang; Xiao, Penny; Webley, Paul; Zhai, Yuchun

2011-11-15

ETS-4 and ETS-10 titanosilicates were prepared from fly ash and anatase, as silica and titanium sources respectively, via a hydrothermal procedure for the first time. The fusion of fly ash by alkali was carried out at a relatively low temperature and the use potassium fluoride salt was avoided in the synthesis of ETS. The by-product of this process is mainly NaCl, which is a useful source material for industry. The energy efficiency and yield of the synthesis process was improved by directly recycling the final filtrate after recovering the product viz ETS-4. All the ETS materials were characterized in terms of structural morphology, thermal stability and surface/pore properties. The properties of ETS-4 prepared from fly ash by the filtrate recycling method were comparable to that from commercial sources. The results show that ETS type materials can be prepared from cheaper resources, with good purity, comparable physico-chemical properties as well as excellent adsorption properties with lower environmental impact. Copyright © 2011 Elsevier B.V. All rights reserved.

Characterization of polymer decomposition products by laser desorption mass spectrometry

NASA Technical Reports Server (NTRS)

Pallix, Joan B.; Lincoln, Kenneth A.; Miglionico, Charles J.; Roybal, Robert E.; Stein, Charles; Shively, Jon H.

1993-01-01

Laser desorption mass spectrometry has been used to characterize the ash-like substances formed on the surfaces of polymer matrix composites (PMC's) during exposure on LDEF. In an effort to minimize fragmentation, material was removed from the sample surfaces by laser desorption and desorbed neutrals were ionized by electron impact. Ions were detected in a time-of-flight mass analyzer which allows the entire mass spectrum to be collected for each laser shot. The method is ideal for these studies because only a small amount of ash is available for analysis. Three sets of samples were studied including C/polysulfone, C/polyimide and C/phenolic. Each set contains leading and trailing edge LDEF samples and their respective controls. In each case, the mass spectrum of the ash shows a number of high mass peaks which can be assigned to fragments of the associated polymer. These high mass peaks are not observed in the spectra of the control samples. In general, the results indicate that the ash is formed from decomposition of the polymer matrix.

Column temperature programming in enantioseparation of dihydropyrimidinone compounds using derivatized cellulose and amylose chiral stationary phases.

PubMed

Wang, Fang; Yeung, David; Han, Jun; Semin, David; McElvain, James S; Cheetham, Janet

2008-03-01

We report the application of column temperature programs as a tool to examine unusual temperature-induced behaviors of polysaccharide chiral stationary phases (CSPs). Using dihydropyrimidinone (DHP) compounds as probes we observed the heating (10-50 degrees C) and cooling (50-10 degrees C) van't Hoff plots of retention factors and/or selectivities of DHP compounds were not superimposable on AD, IA, and AS-H columns solvated with ethanol (EtOH)/n-hexane (n-Hex) mobile phases. The plots were not superimposable on AD, IB, and AS-H columns solvated with 2-propanol (2-PrOH)/n-Hex mobile phases. The thermally induced path-dependant behaviors were caused by slow equilibration as evidenced by the disappearance of the hysteresis in the second heating to cooling cycle and in a cooling to heating cycle. From the step-temperature program (10-50-10 degrees C), only EtOH solvated AD and AS-H phases showed the change of retention factors and/or selectivities with time while only 2-PrOH solvated AS-H phase showed similar behaviors.

Competitive adsorption of Pb2+ and Zn2+ ions from aqueous solutions by modified coal fly ash

NASA Astrophysics Data System (ADS)

Astuti, Widi; Martiani, Wulan; Any Ismawati Khair, N.

2017-03-01

Coal fly ash (CFA), which is a solid waste generated in large amounts worldwide, is mainly composed of some oxides having high crystallinity, including quartz (SiO2) and mullite (3Al2O3 2SiO2), and unburned carbon as a mesopore material that enables it to act as a dual site adsorbent. To decrease the crystallinity, CFA was modified by sodium hydroxide treatment. The modified fly ash (MFA) contains lower amount of Si and Al and has a higher specific surface area than the untreated fly ash (CFA). The objective of this study is to investigate the competitive adsorption of Pb2+ and Zn2+ from aqueous solutions by CFA and MFA. The effect of pH, contact time and initial concentration was investigated. Effective pH for Pb2+ and Zn2+ removal was 4. A greater percentage of Pb2+ and Zn2+ was removed with a decrease in the initial concentration of Pb2+ and Zn2+. Quasi-equilibrium reached in 240 min.

Effect of molecular shape on rotation under severe confinement

DOE PAGES

Dhiman, Indu; Bhowmik, Debsindhu; Shrestha, Utsab R.; ...

2018-01-31

Orientational structure and dynamics of molecules is known to be affected by confinement in space comparable in size to the molecule itself. ZSM-5 with porous channels of ≈0.55 nm is such a porous medium, which offers a strict spatial confinement on low molecular weight hydrocarbons. An important factor that determines these properties is the shape of the confined molecules. In this work, we employed molecular dynamics simulation to study the orientational structure and dynamics of four molecules that differ in shape but have similar kinetic diameters and moments of inertia, confined in ZSM-5. The effect of molecular shape on themore » orientational structure and dynamics of propane, acetonitrile, acetaldehyde and acetone in ZSM-5 is studied by means of probing the differences in the orientational distribution of molecules in the ZSM-5 channels, and extracting time scales of the decay of correlation functions related to rotational motion. Orientational correlation functions of all the four molecules exhibit two regimes of rotational motion. While the short time regime represents free rotation of the molecules before they collide with the pore walls, the long time orientational jumps driven by inter-channel migrations give rise to a very slow varying second regime. Of the molecules studied, orientational structure and dynamics of propane is found to be least affected by confinement under ZSM-5, whereas charge and shape asymmetry of other molecules makes their interchannel migration-driven rotation slow. The time scales involved in the rotational motion for the molecules studied are compared with similar studies reported in literature. Lastly, this study reveals the important role that molecular shape plays in the behavior of confined molecules.« less

Effect of molecular shape on rotation under severe confinement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dhiman, Indu; Bhowmik, Debsindhu; Shrestha, Utsab R.

Orientational structure and dynamics of molecules is known to be affected by confinement in space comparable in size to the molecule itself. ZSM-5 with porous channels of ≈0.55 nm is such a porous medium, which offers a strict spatial confinement on low molecular weight hydrocarbons. An important factor that determines these properties is the shape of the confined molecules. In this work, we employed molecular dynamics simulation to study the orientational structure and dynamics of four molecules that differ in shape but have similar kinetic diameters and moments of inertia, confined in ZSM-5. The effect of molecular shape on themore » orientational structure and dynamics of propane, acetonitrile, acetaldehyde and acetone in ZSM-5 is studied by means of probing the differences in the orientational distribution of molecules in the ZSM-5 channels, and extracting time scales of the decay of correlation functions related to rotational motion. Orientational correlation functions of all the four molecules exhibit two regimes of rotational motion. While the short time regime represents free rotation of the molecules before they collide with the pore walls, the long time orientational jumps driven by inter-channel migrations give rise to a very slow varying second regime. Of the molecules studied, orientational structure and dynamics of propane is found to be least affected by confinement under ZSM-5, whereas charge and shape asymmetry of other molecules makes their interchannel migration-driven rotation slow. The time scales involved in the rotational motion for the molecules studied are compared with similar studies reported in literature. Lastly, this study reveals the important role that molecular shape plays in the behavior of confined molecules.« less

Study on Strength Behavior of Organic Soil Stabilized with Fly Ash

PubMed Central

Molla, Md. Keramat Ali; Sarkar, Grytan

2017-01-01

The aim of this study is to investigate the effect of fly ash on the consistency, compactness, acidic properties, and strength of organic soil. The presence of organic content in the soil has detrimental impacts on the physical and strength behavior of soil. To investigate the effectiveness of fly ash in the stabilization of organic soil, two types of fly ashes (Type I and Type II) at different percentages were used. It is found that fly ash significantly reduces the plasticity index of the organic soil, whereas the liquid and plastic limits increase. The dry density of the fly ash-soil mixture increases significantly, while the water requirement reduces due to the addition of fly ash. The increase of dry density compromises higher strength. The increase of qu with the increase of fly ash content is mainly due to the pozzolanic reaction of fly ash, although the reduction in water content results from the addition of dry fly ash solid. Moreover, Type I fly ash contributes a higher value of qu compared to Type II fly ash. This is attributed to the characteristics of fly ash including CaO and CaO/SiO2 ratio. PMID:29085881

Wood Ash Induced pH Changes Strongly Affect Soil Bacterial Numbers and Community Composition

PubMed Central

Bang-Andreasen, Toke; Nielsen, Jeppe T.; Voriskova, Jana; Heise, Janine; Rønn, Regin; Kjøller, Rasmus; Hansen, Hans C. B.; Jacobsen, Carsten S.

2017-01-01

Recirculation of wood ash from energy production to forest soil improves the sustainability of this energy production form as recycled wood ash contains nutrients that otherwise would be lost at harvest. In addition, wood-ash is beneficial to many soils due to its inherent acid-neutralizing capabilities. However, wood ash has several ecosystem-perturbing effects like increased soil pH and pore water electrical conductivity both known to strongly impact soil bacterial numbers and community composition. Studies investigating soil bacterial community responses to wood ash application remain sparse and the available results are ambiguous and remain at a general taxonomic level. Here we investigate the response of bacterial communities in a spruce forest soil to wood ash addition corresponding to 0, 5, 22, and 167 t wood ash ha-1. We used culture-based enumerations of general bacteria, Pseudomonas and sporeforming bacteria combined with 16S rRNA gene amplicon sequencing to valuate soil bacterial responses to wood ash application. Results showed that wood ash addition strongly increased soil pH and electrical conductivity. Soil pH increased from acidic through neutral at 22 t ha-1 to alkaline at 167 t ha-1. Bacterial numbers significantly increased up to a wood ash dose of 22 t ha-1 followed by significant decrease at 167 t ha-1 wood ash. The soil bacterial community composition changed after wood ash application with copiotrophic bacteria responding positively up to a wood ash dose of 22 t ha-1 while the adverse effect was seen for oligotrophic bacteria. Marked changes in bacterial community composition occurred at a wood ash dose of 167 t ha-1 with a single alkaliphilic genus dominating. Additionally, spore-formers became abundant at an ash dose of 167 t ha-1 whereas this was not the case at lower ash doses. Lastly, bacterial richness and diversity strongly decreased with increasing amount of wood ash applied. All of the observed bacterial responses can be directly explained by the wood ash induced changes in pH, electrical conductivity and the addition of wood ash inherent nutrients. PMID:28804476

Wood Ash Induced pH Changes Strongly Affect Soil Bacterial Numbers and Community Composition.

PubMed

Bang-Andreasen, Toke; Nielsen, Jeppe T; Voriskova, Jana; Heise, Janine; Rønn, Regin; Kjøller, Rasmus; Hansen, Hans C B; Jacobsen, Carsten S

2017-01-01

Recirculation of wood ash from energy production to forest soil improves the sustainability of this energy production form as recycled wood ash contains nutrients that otherwise would be lost at harvest. In addition, wood-ash is beneficial to many soils due to its inherent acid-neutralizing capabilities. However, wood ash has several ecosystem-perturbing effects like increased soil pH and pore water electrical conductivity both known to strongly impact soil bacterial numbers and community composition. Studies investigating soil bacterial community responses to wood ash application remain sparse and the available results are ambiguous and remain at a general taxonomic level. Here we investigate the response of bacterial communities in a spruce forest soil to wood ash addition corresponding to 0, 5, 22, and 167 t wood ash ha -1 . We used culture-based enumerations of general bacteria, Pseudomonas and sporeforming bacteria combined with 16S rRNA gene amplicon sequencing to valuate soil bacterial responses to wood ash application. Results showed that wood ash addition strongly increased soil pH and electrical conductivity. Soil pH increased from acidic through neutral at 22 t ha -1 to alkaline at 167 t ha -1 . Bacterial numbers significantly increased up to a wood ash dose of 22 t ha -1 followed by significant decrease at 167 t ha -1 wood ash. The soil bacterial community composition changed after wood ash application with copiotrophic bacteria responding positively up to a wood ash dose of 22 t ha -1 while the adverse effect was seen for oligotrophic bacteria. Marked changes in bacterial community composition occurred at a wood ash dose of 167 t ha -1 with a single alkaliphilic genus dominating. Additionally, spore-formers became abundant at an ash dose of 167 t ha -1 whereas this was not the case at lower ash doses. Lastly, bacterial richness and diversity strongly decreased with increasing amount of wood ash applied. All of the observed bacterial responses can be directly explained by the wood ash induced changes in pH, electrical conductivity and the addition of wood ash inherent nutrients.

Properties of Fly Ash Blocks Made from Adobe Mould

NASA Astrophysics Data System (ADS)

Chokhani, Alankrit; Divakar, B. S.; Jawalgi, Archana S.; Renukadevi, M. V.; Jagadish, K. S.

2018-02-01

Fly ash being one of the industrial waste products poses a serious disposal problem. This paper presents an experimental study of utilization of fly ash to produce blocks with varying proportions and mix combinations. Composition of fly ash blocks mainly consist of fly ash and sand, with cementitious product as either cement, lime or both, such as fly ash-sand-cement, fly ash-sand-lime and fly ash-sand-cement-lime are used. Four different proportions for each of the mix combinations are experimented. Compressive strength, water absorption, Initial rate of absorption, and dry density of fly ash blocks are studied. The influence of partial and complete replacement of cement by lime is examined.

Properties of Fly Ash Blocks Made from Adobe Mould

NASA Astrophysics Data System (ADS)

Chokhani, Alankrit; Divakar, B. S.; Jawalgi, Archana S.; Renukadevi, M. V.; Jagadish, K. S.

2018-06-01

Fly ash being one of the industrial waste products poses a serious disposal problem. This paper presents an experimental study of utilization of fly ash to produce blocks with varying proportions and mix combinations. Composition of fly ash blocks mainly consist of fly ash and sand, with cementitious product as either cement, lime or both, such as fly ash-sand-cement, fly ash-sand-lime and fly ash-sand-cement-lime are used. Four different proportions for each of the mix combinations are experimented. Compressive strength, water absorption, Initial rate of absorption, and dry density of fly ash blocks are studied. The influence of partial and complete replacement of cement by lime is examined.

Control of plasma stored energy for burn control using DIII-D in-vessel coils

DOE PAGES

Hawryluk, Richard J.; Eidietis, Nicholas W.; Grierson, Brian A.; ...

2015-04-09

A new approach has been experimentally demonstrated to control the stored energy by applying a non-axisymmetric magnetic field using the DIII-D in-vessel coils to modify the energy confinement time. In future burning plasma experiments as well as magnetic fusion energy power plants, various concepts have been proposed to control the fusion power. The fusion power in a power plant operating at high gain can be related to the plasma stored energy and hence, is a strong function of the energy confinement time. Thus, an actuator that modifies the confinement time can be used to adjust the fusion power. In relativelymore » low collisionality DIII-D discharges, the application of nonaxisymmetric magnetic fields results in a decrease in confinement time and density pumpout. Furthermore, gas puffing was used to compensate the density pumpout in the pedestal while control of the stored energy was demonstrated by the application of non-axisymmetric fields.« less

Investigation on Leaching Behaviour of Fly Ash and Bottom Ash Replacement in Self-Compacting Concrete

NASA Astrophysics Data System (ADS)

Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Bakri Abdullah, Mohd Mustafa Al

2016-06-01

Fly ash and bottom ash are some of the waste generated by coal-fired power plants, which contains large quantities of toxic and heavy metals. In recent years, many researchers have been interested in studying on the properties of self-compacting concrete incorporated with fly ash and bottom ash but there was very limited research from the combination of fly ash and bottom ash towards the environmental needs. Therefore, this research was focused on investigating the leachability of heavy metals of SCC incorporated with fly ash and bottom ash by using Toxicity Characteristic Leaching Procedure, Synthetic Precipitation Leaching Procedure and Static Leaching Test. The samples obtained from the coal-fired power plant located at Peninsula, Malaysia. In this study, the potential heavy metals leached out from SCC that is produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a substitute for sand with the ratios from 10% to 30% respectively were designated and cast. There are eight heavy metals of concern such as As, Cr, Pb, Zn, Cu, Ni, Mn and Fe. The results indicated that most of the heavy metals leached below the permissible limits from the United States Environmental Protection Agency and World Health Organization limit for drinking water. As a conclusion, the minimum leaching of the heavy metals from the incorporation of fly ash and bottom ash in self-compacting concrete was found in 20% of fly ash and 20% of bottom ash replacement. The results also indicate that this incorporation could minimize the potential of environmental problems.

Differential response in foliar chemistry of three ash species to emerald ash borer adult feeding.

PubMed

Chen, Yigen; Whitehill, Justin G A; Bonello, Pierluigi; Poland, Therese M

2011-01-01

The emerald ash borer (EAB; Agrilus planipennis Fairmaire; Coleoptera: Buprestidae), is an exotic wood-boring beetle that has been threatening North American ash (Fraxinus spp.) resources since its discovery in Michigan and Ontario in 2002. In this study, we investigated the phytochemical responses of the three most common North American ash species (black, green, and white ash) in northeastern USA to EAB adult feeding. Black ash was the least responsive to EAB adult feeding in terms of the induction of volatile compounds, and levels of only two (indole and benzyl cyanide) of the 11 compounds studied increased. In green ash, levels of two [(E)-β-ocimene and indole] of the 11 volatile compounds studied were elevated, while the levels of two green leaf volatiles [hexanal and (E)-2-hexenal] decreased. White ash showed the greatest response with an increase in levels of seven of the 11 compounds studied. Qualitative differences among ash species were detected. Among the phenolic compounds detected, ligustroside was the only one detected in all three species. Oleuropein aglycone and 2 unidentified compounds were found only in black ash; coumaroylquinic acid and feruloylquinic acid were detected only in green ash; and verbascoside hexoside was detected only in white ash. EAB adult feeding did not elicit or decrease concentrations of any selected individual phenolic compounds. However, although levels of total phenolics from black and green ash foliage were not affected by EAB adult feeding, they decreased significantly in white ash. EAB adult feeding elevated chymotrypsin inhibitors in black ash. The possible ecological implications of these findings are discussed.

Spatio-temporal effects of low severity grassland fire on soil colour

NASA Astrophysics Data System (ADS)

Pereira, Paulo; Cerdà, Artemi; Bolutiene, Violeta; Pranskevicius, Mantas; Úbeda, Xavier; Jordán, Antonio; Zavala, Lorena; Mataix-Solera, Jorge

2013-04-01

Fire changes soil properties directly, through temperature, or indirectly with ash deposition and the temporal elimination of vegetal cover. Both influences change soil colour and soil properties. The degree of changes depends on fire severity that has important implications on soil organic matter, texture, mineralogy and hydrological properties and type of ash produced. The ash colour is different according to the temperature of combustion and burned specie and this property will have implications on soil colour. In addition, ash properties have a strong spatial variability. The aim of this work is to study the spatio-temporal effects of a low severity grassland fire on soil colour occurred in Lithuania, near Vilnius city (54° 42' N, 25° 08' E, 158 m.a.s.l.). After the fire it was designed a plot of 20x20m in a burned and unburned flat area. Soil colour was analysed immediately after the fire, and 2, 5, 7 and 9 months after the fire. In each sampling 25 soil samples were collected, carried out to the laboratory, dried at room temperature (20-24° C) and sieved with the <2mm mesh. Soil colour was observed with the Munsell colour chart and the soil chroma value (CV) was observed. Since data did not respected the Gaussian distribution a neperian logarithmic (ln) transformation was applied. Differences among time and between plots were observed with the repeated measures ANOVA test, followed by a Tukey HSD test. Differences were significant at a p<0.05. The spatial variability (SV) was assessed with the coefficient of variation using non transformed data. The results showed differences among time at a p<0.001, treatment at a p<0.01 and time x treatment at a p<0.01. This means that fire during the first 9 months changed significantly soil colour. The CV of the burned plot was lower than the control plot (darker colour), that is attributed to the deposition of charred material and charcoal. This ash produced in this fire was mainly black coloured. With the time the soil of the burned plot became lighter, due the movement of charred material and charcoal in depth through soil profile. After the fire SV was higher in the burned plot (13.27%) than in the unburned plot (7.95%). This major variability might be attributed to ash influence, since this fire did nit had direct effects on soil. Despite the reduced CV, some patches burned at higher severity, and ash was dark and light grey and this might had influences on soil colour SV. In the following measurements SV was very similar, but always slightly higher in the control plot than in the burned plot. Two months, unburned 15.52% and burned, 14.70%. Five months, unburned, 14.78% and burned 14.42%, Seven months, unburned, 15.15% and burned, 14.67%. Nine months, unburned, 18.96% and burned 17.84%. After the fire ash can be (re)distributed uncountable times. In the immediate period after the fire, finner ash produced at higher severities is easily transported by wind and can remix (Pereira et al., 2013a, Pereira et al., 2013b) and change soil colour. In this fire, vegetation recovered very fast, thus this process might occurred only in the first weeks after the fire (Pereira et al., 2013c). Since vegetation recovered fast, soil colour SV depended on carbon and charred material movement in depth soil profile. Further studies are needed on the soil colour evolution after the fire, since can be an indicator of soil properties such as temperature reached with implications in other soil properties. Acknowledgements The authors appreciated the support of the project "Litfire", Fire effects in Lithuanian soils and ecosystems (MIP-048/2011) funded by the Lithuanian Research Council, Spanish Ministry of Science and Innovation for funding through the HYDFIRE project CGL2010-21670-C02-01, FUEGORED (Spanish Network of Forest Fire Effects on Soils http://grupo.us.es/fuegored/) and to Comissionat per a Universitats i Recerca del DIUE de la Generalitat de Catalunya. References Pereira, P. Cerdà, A., Úbeda, X., Mataix-Solera, J. Arcenegui, V., Zavala, L. (2013a) Modelling the impacts of wildfire on ash thickness in a short-term period, Land Degradation and Development (In press) DOI: 10.1002/ldr.2195 Pereira, P., Cerdà, A., Úbeda, X., Mataix-Solera, J., Martin, D.A., Jordan, A. Burguet, M. (2013b) Effects of fire on ash thickness in a Lithuanian grassland and short-term spatio-temporal changes. Solid Earth Discussions, 4 (1), 1545-1584. doi:10.5194/sed-4-1-2012 Pereira, P., Pranskevicius, M., Cepanko, V., Vaitkute, D., Pundyte, N., Ubeda, X., Mataix-Soler, J., Cerda, A., Martin, D.A. (2013c) Short time vegetation recovers after a spring grassland fire in Lithuania. Temporal and slope position effect, Flamma, 4(1), 13-17.

The future of volcanic ash-aircraft interactions from technical and policy perspectives

NASA Astrophysics Data System (ADS)

Casadevall, T. J.; Guffanti, M.

2010-12-01

Since the advent of jet-powered flight in the 1960s, the threat of volcanic ash to aviation operations has become widely recognized and the mitigation of this threat has received concerted international attention. At the same time the susceptibility to operational disruption has grown. Technical improvements to airframes, engines, and avionic systems have been made in response to the need for improved fuel efficiency and the demand for increased capacity for passenger and freight traffic. Operational demands have resulted in the growth of extended overseas flight operations (ETOPS), increased flight frequency on air traffic routes, and closer spacing of aircraft on heavily traveled routes. The net result has been great advances in flight efficiency, but also increased susceptibility to flight disruption, especially in heavily traveled regions such as North Atlantic-Europe, North America, and the North Pacific. Advances in ash avoidance procedures, pilot and air manager training, and in detection of ash-related damage and maintenance of aircraft and engines have been spurred by noteworthy eruptions such as Galunggung, Indonesia, 1982; Redoubt, Alaska, 1989-1990; and Pinatubo, Philippines, 1991. Comparable advances have been made in the detection and tracking of volcanic ash clouds using satellite-based remote sensing and numerical trajectory forecast models. Following the April 2010 eruption of Eyjafjallajökull volcano, Iceland, the global aviation community again focused attention on the issue of safe air operations in airspace affected by volcanic ash. The enormous global disruption to air traffic in the weeks after the Eyjafjallajökull eruption has placed added emphasis for the global air traffic management system as well as on the equipment manufacturers to reevaluate air operations in ash-affected airspace. Under the leadership of the International Civil Aviation Organization and the World Meteorological Organization, efforts are being made to address this growth in the risks facing aviation operation owing to volcanic ash hazard (http://www2.icao.int/en/anb/met-aim/met/ivatf/Documents/Final.Alltext.pdf) Modifications of international procedures for air traffic management, a new assessment of equipment vulnerability, and efforts to detect and to more precisely forecast the distribution and concentration of volcanic ash are underway. These efforts will result in modification and updating of current practices for advising and warning pilots and airspace managers about volcanic ash, and also in better understandings of the threat volcanic ash presents to aviation operations. While technical and policy changes will help improve flight safety, there continues to be a role for earth scientists to work with the aviation community to improve monitoring of volcanoes, especially in remote regions, and in understanding of explosive volcanic processes. A paramount need continues for improved communications amongst all of the scientific and technical parties to address and successfully mitigate the risks of volcanic ash to aviation operations.

Above and below ground carbohydrate allocation differs between ash (Fraxinus excelsior L.) and beech (Fagus sylvatica L.)

PubMed Central

Thoms, Ronny; Köhler, Michael; Gessler, Arthur

2017-01-01

We investigated soluble carbohydrate transport in trees that differed in their phloem loading strategies in order to better understand the transport of photosynthetic products into the roots and the rhizosphere as this knowledge is needed to better understand the respiratory processes in the rhizosphere. We compared beech, which is suggested to use mainly passive loading of transport sugars along a concentration gradient into the phloem, with ash that uses active loading and polymer trapping of raffinose family oligosaccharides (RFOs). We pulse-labeled 20 four-year old European beech and 20 four-year old ash trees with 13CO2 and tracked the fate of the label within different plant compartments. We extracted soluble carbohydrates from leaves, bark of stems and branches, and fine roots, measured their amount and isotopic content and calculated their turnover times. In beech one part of the sucrose was rapidly transported into sink tissues without major exchange with storage pools whereas another part of sucrose was strongly exchanged with unlabeled possibly stored sucrose. In contrast the storage and allocation patterns in ash depended on the identity of the transported sugars. RFO were the most important transport sugars that had highest turnover in all shoot compartments. However, the turnover of RFOs in the roots was uncoupled from the shoot. The only significant relation between sugars in the stem base and in the roots of ash was found for the amount (r2 = 0.50; p = 0.001) and isotopic content (r2 = 0.47; p = 0.01) of sucrose. The negative relation of the amounts suggested an active transport of sucrose into the roots of ash. Sucrose concentration in the root also best explained the concentration of RFOs in the roots suggesting that RFO in the roots of ash may be resynthesized from sucrose. Our results interestingly suggest that in both tree species only sucrose directly entered the fine root system and that in ash RFOs are transported indirectly into the fine roots only. The direct transport of sucrose might be passive in beech but active in ash (sustained active up- and unloading to co-cells), which would correspond to the phloem loading strategies. Our results give first hints that the transport of carbohydrates between shoot and root is not necessarily continuous and involves passive (beech) and active (ash) transport processes, which may be controlled by the phloem unloading. PMID:28934229

Design of a single batch leaching test to assess the environmental impact of volcanic ash

NASA Astrophysics Data System (ADS)

Fernandez-Turiel, J.; Ruggieri, F.; Saavedra, J.; Gimeno, D.; Martinez, L.; Galindo, G.; Garcia-Valles, M.; Polanco, E.; Perez-Torrado, F.; Rodriguez-Gonzalez, A.; Rodriguez-Fernandez, D.

2010-12-01

Most of the environmentally mobile constituents of volcanic ashes may be detected by one stage batch leaching tests, but the lack of a standardized procedure makes difficult the comparison between different studies. A series of batch tests were conducted using rhyolithic Andean ashes of the Chaiten 2008 eruption (Chile) and an ancient (hundreds of thousands of years) eruption in the southern Puna (NW Argentina) in order to propose a batch test susceptible of harmonization for volcanic ash. Tests carried out varying amount of ash (0.1 and 1 g), leachant volume (1, 2, 5, 10, 25 and 50 ml of deionized water) and contact time (1.5, 4 and 16 h). The mixture of ash and leachant was shaken at 20 rpm at room temperature in polypropylene test tubes (14x100 mm) or polyethylene (HDPE) reactors (50 and 100 ml), depending on the leachate volume. Leachate solutions, previous centrifugation (3000 rpm) during 15 minutes, were filtered through PVDF syringe filters with tube tip (25 mm diameter and 0.45 µm pore size) and made up to 100 ml volume in 1% (v/v) HNO3. These solutions were analyzed by ICP-OES, ICP-MS and ISE (fluoride). Leaching tests with 0.1 g of ash have a low reproducibility of results whereas leachant volume has not a great influence on the element contents released when 1 g of sample is employed. Batch leaching tests performed at 1.5 and 16 h are less reproducible that those tested at 4 h. The best batch leaching conditions tested correspond to 1 g of ash and 10 ml of deionized water shaking during 4 h. This methodology has been applied to recent and historical eruptions of the Southern Volcanic Zone of the Andes (Quizapu, 1932; Lonquimay, 1988; Hudson, 1991; Copahue, 2000; Llaima 2008; Chaiten 2008), the Central Volcanic Zone of the Andes (Quaternary ashes of different eruptions in southern Puna and neighboring areas in northwestern Argentina), and the recent eruption of Eyjafjallajokull (april-may 2010) in Iceland. The method developed is reproducible, fast and reliable in laboratory conditions and the results easily applicable to environmental impact models. This study was carried out in the framework of the PEGEFA Working Group (Catalonian Government 2009-SGR-972), and was funded by the Project ASH of the Spanish MICINN (CGL2008-00099) and the FPU Grant of the Spanish Ministry of Education of one of the authors (F. Ruggieri, Ref. AP2006-04592).

Particle interaction and rheological behavior of cement-based materials at micro- and macro-scales

NASA Astrophysics Data System (ADS)

Lomboy, Gilson Rescober

Rheology of cement based materials is controlled by the interactions at the particle level. The present study investigates the particle interactions and rheological properties of cement-based materials in the micro- and macro-scales. The cementitious materials studied are Portland cement (PC), fly ash (FA), ground granulated blast furnace slag (GGBFS) and densified silica fume (SF). At the micro-scale, aside from the forces on particles due to collisions, interactions of particles in a flowing system include the adhesion and friction. Adhesion is due to the attraction between materials and friction depends on the properties of the sliding surfaces. Atomic Force Microscopy (AFM) is used to measure the adhesion force and coefficient of friction. The adhesion force is measured by pull-off force measurements and is used to calculate Hamaker constants. The coefficient of friction is measured by increasing the deflection set-points on AFM probes with sliding particles, thereby increasing normal loads and friction force. AFM probes were commercial Si3N4 tips and cementitious particles attached to the tips of probe cantilevers. SF was not included in the micro-scale tests due to its limiting size when attaching it to the AFM probes. Other materials included in the tests were silica, calcite and mica, which were used for verification of the developed test method for the adhesion study. The AFM experiments were conducted in dry air and fluid environments at pH levels of 7, 8, 9, 11 and 13. The results in dry air indicate that the Hamaker constant of Class F FA can be similar to PC, but Class C FA can have a high Hamaker constant, also when in contact with other cementitious materials. The results in fluid environments showed low Hamaker constants for Class F fly ashes compared to PC and also showed high Hamaker constants for PC and Class C fly ash. The results for the friction test in dry air indicated that the coefficient of friction of PC is lower than fly ashes, which is attributed to the asperities present on the particle surface. At the macro-scale, flow of cementitious materials may be in its dry or wet state, during transport and handling or when it is used in concrete mixtures, respectively. Hence, the behavior of bulk cementitious materials in their dry state and wet form are studied. In the dry state, the compression, recompression and swell indices, and stiffness modulus of plain and blended cementitious materials are determined by confined uniaxial compression. The coefficients of friction of the bulk materials studied are determined by a direct shear test. The results indicate that shape of particles has a great influence on the compression and shear parameters. The indices for PC blends with FA do not change with FA replacement, while it increases with GGBFS replacement. Replacement with GGBFS slightly decreases coefficient of friction, while replacement with FA significantly decreases coefficient of friction. At low SF replacement, coefficient of friction decreases. In wet state, unary, binary, ternary and quaternary mixes with w/b of 0.35, 0.45 and 0.55 were tested for yield stress, viscosity and thixotropy. It is found that fly ash replacement lowers the rheological properties and replacement with GGBFS and SF increases rheological properties. The distinct element method (DEM) was employed to model particle interaction and bulk behavior. The AFM force curve measurement is simulated to validate the adhesion model in the DEM. The contact due to asperities was incorporated by considering the asperities as a percentage of the radius of the contacting particles. The results of the simulation matches the force-curve obtained from actual AFM experiments. The confined uniaxial compression test is simulated to verify the use of DEM to relate micro-scale properties to macros-scale behavior. The bulk stiffness from the physical experiments is matched in the DEM simulation. The particle stiffness and coefficient of friction are found to have a direct relation to bulk stiffness.

Three-year progression of emerald ash borer-induced decline and mortality in southeastern Michigan

Treesearch

Kamal J.K. Gandhi; Annemarie Smith; Robert P. Long; Robin A.J. Taylor; Daniel A. Herms

2008-01-01

We monitored the progression of ash (Fraxinus spp.) decline and mortality due to emerald ash borer (EAB), Agrilus planipennis, in 38 forest stands in the upper Huron River watershed region of southeastern Michigan from 2004-2007. Black ash (F. nigra), green ash (F. pennsylvanica), and white ash...

Genetic transformation of Fraxinus spp. for resistance to the emerald ash borer

Treesearch

Paula M. Pijut; Rochelle R. Beasley; Kaitlin J. Palla

2010-01-01

The emerald ash borer (EAB; Agrilus planipennis Fairmaire) (Coleoptera; Buprestidae) is a wood-boring beetle that poses substantial risk to the ash resource in North America. Ash species native to the United States and known to be susceptible to EAB are Fraxinus pennsylvanica (green ash), F. americana (white ash...

Cancer cell motility: lessons from migration in confined spaces

PubMed Central

Paul, Colin D.; Mistriotis, Panagiotis; Konstantopoulos, Konstantinos

2017-01-01

Time-lapse, deep-tissue imaging made possible by advances in intravital microscopy has demonstrated the importance of tumour cell migration through confining tracks in vivo. These tracks may either be endogenous features of tissues or be created by tumour or tumour-associated cells. Importantly, migration mechanisms through confining microenvironments are not predicted by 2D migration assays. Engineered in vitro models have been used to delineate the mechanisms of cell motility through confining spaces encountered in vivo. Understanding cancer cell locomotion through physiologically relevant confining tracks could be useful in developing therapeutic strategies to combat metastasis. PMID:27909339

An FP7 "Space" project: Aphorism "Advanced PRocedures for volcanic and Seismic Monitoring"

NASA Astrophysics Data System (ADS)

Di Iorio, A., Sr.; Stramondo, S.; Bignami, C.; Corradini, S.; Merucci, L.

2014-12-01

APHORISM project proposes the development and testing of two new methods to combine Earth Observation satellite data from different sensors, and ground data. The aim is to demonstrate that this two types of data, appropriately managed and integrated, can provide new improved GMES products useful for seismic and volcanic crisis management. The first method, APE - A Priori information for Earthquake damage mapping, concerns the generation of maps to address the detection and estimate of damage caused by a seism. The use of satellite data to investigate earthquake damages is not an innovative issue. We can find a wide literature and projects concerning such issue, but usually the approach is only based on change detection techniques and classifications algorithms. The novelty of APE relies on the exploitation of a priori information derived by InSAR time series to measure surface movements, shake maps obtained from seismological data, and vulnerability information. This a priori information is then integrated with change detection map to improve accuracy and to limit false alarms. The second method deals with volcanic crisis management. The method, MACE - Multi-platform volcanic Ash Cloud Estimation, concerns the exploitation of GEO (Geosynchronous Earth Orbit) sensor platform, LEO (Low Earth Orbit) satellite sensors and ground measures to improve the ash detection and retrieval and to characterize the volcanic ash clouds. The basic idea of MACE consists of an improvement of volcanic ash retrievals at the space-time scale by using both the LEO and GEO estimations and in-situ data. Indeed the standard ash thermal infrared retrieval is integrated with data coming from a wider spectral range from visible to microwave. The ash detection is also extended in case of cloudy atmosphere or steam plumes. APE and MACE methods have been defined in order to provide products oriented toward the next ESA Sentinels satellite missions.The project is funded under the European Union FP7 program and the Kick-Off meeting has been held at INGV premises in Rome on 18th December 2013.

Removal of boron from ceramic industry wastewater by adsorption-flocculation mechanism using palm oil mill boiler (POMB) bottom ash and polymer.

PubMed

Chong, Mei Fong; Lee, Kah Peng; Chieng, Hui Jiun; Syazwani Binti Ramli, Ili Izyan

2009-07-01

Boron is extensively used in the ceramic industry for enhancing mechanical strength of the tiles. The discharge of boron containing wastewater to the environment causes severe pollution problems. Boron is also dangerous for human consumption and causes organisms' reproductive impediments if the safe intake level is exceeded. Current methods to remove boron include ion-exchange, membrane filtration, precipitation-coagulation, biological and chemical treatment. These methods are costly to remove boron from the wastewater and hence infeasible for industrial wastewater treatment. In the present research, adsorption-flocculation mechanism is proposed for boron removal from ceramic wastewater by using Palm Oil Mill Boiler (POMB) bottom ash and long chain polymer or flocculant. Ceramic wastewater is turbid and milky in color which contains 15 mg/L of boron and 2000 mg/L of suspended solids. The optimum operating conditions for boron adsorption on POMB bottom ash and flocculation using polymer were investigated in the present research. Adsorption isotherm of boron on bottom ash was also investigated to evaluate the adsorption capacity. Adsorption isotherm modeling was conducted based on Langmuir and Freundlich isotherms. The results show that coarse POMB bottom ash with particle size larger than 2 mm is a suitable adsorbent where boron is removed up to 80% under the optimum conditions (pH=8.0, dosage=40 g bottom ash/300 ml wastewater, residence time=1h). The results also show that KP 1200 B cationic polymer is effective in flocculating the suspended solids while AP 120 C anionic polymer is effective in flocculating the bottom ash. The combined cationic and anionic polymers are able to clarify the ceramic wastewater under the optimum conditions (dosage of KP 1200 B cationic polymer=100 mg/L, dosage of AP 120 C anionic polymer=50 mg/L, mixing speed=200 rpm). Under the optimum operating conditions, the boron and suspended solids concentration of the treated wastewater were reduced to 3 mg/L and 5 mg/L respectively, satisfying the discharge requirement by Malaysia Department of Environment (DOE). The modeling study shows that the adsorption isotherm of boron onto POMB bottom ash conformed to the Freundlich Isotherm. The proposed method is suitable for boron removal in ceramic wastewater especially in regions where POMB bottom ash is abundant.

Detrimental effects of cement mortar and fly ash mortar on asthma progression.

PubMed

Cho, Ara; Jang, Hong-Seok; Roh, Yoon Seok; Park, Hee Jin; Talha, A F S M; So, Seung-Young; Lim, Chae Woong; Kim, Bumseok

2013-11-01

Currently, concrete additive materials are used worldwide to improve properties of concrete production and to reduce the total cost of the materials used in the concrete. However, the effects of exposure to various gases emitted from mortar mixed with additive materials are poorly understood. To evaluate the pattern of gas emission from cement mortar and additives, the emission levels of gas including ammonia (NH3) and volatile organic compounds (VOCs) were measured from two different mortar types, Ordinary Portland Cement (OPC), and OPC with fly ash on various time points after manufacture. On days 1, 3, 10 and 30 after manufacture, moderate concentrations of NH3 (4, 9, 12 and 5 ppm) were measured in OPC mortar (24h, 150 mm × 150 mm × 50 mm), whereas higher concentrations of NH3 (73, 55, 20 and 5 ppm) were measured in OPC mortar with fly ash (24h, 150 mm × 150 mm × 50 mm). Furthermore, the concentration of VOCs was more than 10 ppm on 1, 3, and 10 days of age in OPC and OPC with fly ash mortars. To examine the mortars' allergic effects on the respiratory system, mice were sensitized with ovalbumin (OVA) and divided into four groups: normal, asthma control, OPC mortar and OPC mortar with fly ash. The mice were housed in corresponding group cage for 10 days with OVA challenges to induce asthma. Histopathologically, increased infiltration of lymphocytes was observed in the lung perivascular area of mice housed in OPC mortar and OPC mortar with fly ash cages compared to lungs of asthma control mice. Moreover, severe bronchial lumen obstruction and increased hypertrophy of bronchial epithelial cells (p<0.05) were observed in the OPC mortar with fly ash group compared to OPC mortar or asthma control groups. Lungs of the two mortar groups generally expressed higher levels of genes related with asthma, including IL-4, eotaxin and epidermal growth factor (EGF) compared to lungs of asthma control mice. Additionally, the OPC mortar with fly ash group showed higher expression of IL-5, 13 and monocyte chemoattractant protein-1 (MCP-1) compared to the asthma control group. These results indicate that OPC mortar and OPC mortar with fly ash might exacerbate asthma. Copyright © 2013 Elsevier B.V. All rights reserved.

Utilization of blended fluidized bed combustion (FBC) ash and pulverized coal combustion (PCC) fly ash in geopolymer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chindaprasirt, Prinya; Rattanasak, Ubolluk, E-mail: ubolluk@buu.ac.t

2010-04-15

In this paper, synthesis of geopolymer from fluidized bed combustion (FBC) ash and pulverized coal combustion (PCC) fly ash was studied in order to effectively utilize both ashes. FBC-fly ash and bottom ash were inter-ground to three different finenesses. The ashes were mixed with as-received PCC-fly ash in various proportions and used as source material for synthesis of geopolymer. Sodium silicate (Na{sub 2}SiO{sub 3}) and 10 M sodium hydroxide (NaOH) solutions at mass ratio of Na{sub 2}SiO{sub 3}/NaOH of 1.5 and curing temperature of 65 deg. C for 48 h were used for making geopolymer. X-ray diffraction (XRD), scanning electronmore » microscopy (SEM), degree of reaction, and thermal gravimetric analysis (TGA) were performed on the geopolymer pastes. Compressive strength was also tested on geopolymer mortars. The results show that high strength geopolymer mortars of 35.0-44.0 MPa can be produced using mixture of ground FBC ash and as-received PCC-fly ash. Fine FBC ash is more reactive and results in higher degree of reaction and higher strength geopolymer as compared to the use of coarser FBC ash. Grinding increases reactivity of ash by means of increasing surface area and the amount of reactive phase of the ash. In addition, the packing effect due to fine particles also contributed to increase in strength of geopolymers.« less

Wood ash residue causes a mixture of growth promotion and toxicity in Lemna minor.

PubMed

Jagodzinski, Lucas S; O'Donoghue, Marian T; Heffernan, Liam B; van Pelt, Frank N A M; O'Halloran, John; Jansen, Marcel A K

2018-06-01

The use of wood as a sustainable biofuel results in the generation of residual wood ash. The ash contains high amounts of plant macronutrients such as phosphorus, potassium, calcium as well as several micronutrients. To explore the potential use of wood ash as a fertiliser, the growth enhancing properties of Sitka spruce (Picea sitchensis Bong.) wood ash were contrasted with the potential toxic action, using common duckweed (Lemna minor L.) as a model test species. The growth of L. minor exposed to wood bottom and fly ash solids and corresponding leachates was assessed in ultra-oligotrophic and eutrophic media. Ash solids and leachates were also tested as neutralized preparations. Suspended ash solids promoted L. minor growth up to concentrations of 2.5-5g/L. Leachates promoted growth up to 10g ash equivalents per litre, but for bottom ash only. Beneficial effects of wood ash were most pronounced on ultra-oligotrophic medium. However, on such nutrient-deficient medium severe inhibition of L. minor biomass and frond growth was observed at relatively low concentrations of fly ash (EC 50 =14g/L). On standard, eutrophic medium, higher concentrations of fly ash (EC 50 =21g/L), or neutralized fly ash (EC 50 =37g/L) were required to impede growth. Bottom ash, or neutralized bottom ash retarded growth at concentrations of 51g/L and 74g/L (EC 50 ), respectively, in eutrophic medium. It appears that phytotoxicity is due to the elemental composition of the ash, its alkaline character, and possible interactions between these two properties. Growth promotion was due to the substantial content of plant nutrients. This study underlines the importance of the receiving environment (nutrient status and pH) in determining the balance between toxicity and growth promotion, and shows that the margin between growth promoting and toxicity inducing concentrations can be enlarged through ash neutralization. Copyright © 2017 Elsevier B.V. All rights reserved.

Thermonuclear ignition in inertial confinement fusion and comparison with magnetic confinement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Betti, R.; Chang, P. Y.; Anderson, K. S.

2010-05-15

The physics of thermonuclear ignition in inertial confinement fusion (ICF) is presented in the familiar frame of a Lawson-type criterion. The product of the plasma pressure and confinement time Ptau for ICF is cast in terms of measurable parameters and its value is estimated for cryogenic implosions. An overall ignition parameter chi including pressure, confinement time, and temperature is derived to complement the product Ptau. A metric for performance assessment should include both chi and Ptau. The ignition parameter and the product Ptau are compared between inertial and magnetic-confinement fusion. It is found that cryogenic implosions on OMEGA[T. R. Boehlymore » et al., Opt. Commun. 133, 495 (1997)] have achieved Ptauapprox1.5 atm s comparable to large tokamaks such as the Joint European Torus [P. H. Rebut and B. E. Keen, Fusion Technol. 11, 13 (1987)] where Ptauapprox1 atm s. Since OMEGA implosions are relatively cold (Tapprox2 keV), their overall ignition parameter chiapprox0.02-0.03 is approx5x lower than in JET (chiapprox0.13), where the average temperature is about 10 keV.« less

Ultra-confined surface phonon polaritons in molecular layers of van der Waals dielectrics.

PubMed

Dubrovkin, Alexander M; Qiang, Bo; Krishnamoorthy, Harish N S; Zheludev, Nikolay I; Wang, Qi Jie

2018-05-02

Improvements in device density in photonic circuits can only be achieved with interconnects exploiting highly confined states of light. Recently this has brought interest to highly confined plasmon and phonon polaritons. While plasmonic structures have been extensively studied, the ultimate limits of phonon polariton squeezing, in particular enabling the confinement (the ratio between the excitation and polariton wavelengths) exceeding 10 2 , is yet to be explored. Here, exploiting unique structure of 2D materials, we report for the first time that atomically thin van der Waals dielectrics (e.g., transition-metal dichalcogenides) on silicon carbide substrate demonstrate experimentally record-breaking propagating phonon polaritons confinement resulting in 190-times squeezed surface waves. The strongly dispersive confinement can be potentially tuned to greater than 10 3 near the phonon resonance of the substrate, and it scales with number of van der Waals layers. We argue that our findings are a substantial step towards infrared ultra-compact phonon polaritonic circuits and resonators, and would stimulate further investigations on nanophotonics in non-plasmonic atomically thin interface platforms.

Hydrodynamics of confined colloidal fluids in two dimensions

NASA Astrophysics Data System (ADS)

Sané, Jimaan; Padding, Johan T.; Louis, Ard A.

2009-05-01

We apply a hybrid molecular dynamics and mesoscopic simulation technique to study the dynamics of two-dimensional colloidal disks in confined geometries. We calculate the velocity autocorrelation functions and observe the predicted t-1 long-time hydrodynamic tail that characterizes unconfined fluids, as well as more complex oscillating behavior and negative tails for strongly confined geometries. Because the t-1 tail of the velocity autocorrelation function is cut off for longer times in finite systems, the related diffusion coefficient does not diverge but instead depends logarithmically on the overall size of the system. The Langevin equation gives a poor approximation to the velocity autocorrelation function at both short and long times.

Evaluation of ash from some tropical plants of Nigeria for the control of Sclerotium rolfsii Sacc. on wheat (Triticum aestivum L.).

PubMed

Enikuomehin, O A; Ikotun, T; Ekpo, E J

1998-01-01

Eleven ash samples, from organs of nine tropical plants, were screened for their abilities to inhibit mycelial growth and sclerotial germination of a Nigerian isolate of Sclerotium rolfsii on agar and in the soil. Ten ash samples showed some activity against mycelial growth of S. rolfsii in vitro. Ash samples from Delonix regia stem wood, Mangifera indica leaf and Vernonia amygdalina leaf were most effective as each totally inhibited mycelial growth of S. rolfsii in vitro. Ocimum gratissimum leaf ash, D. regia wood ash and Musa paradisiaca flower bract ash inhibited sclerotial germination on agar. Nine ash samples protected seeds against pre-emergence rot. Ash from M. indica leaf, V. amygdalina leaf and Azadirachta indica leaf protected seedlings against post-emergence infection. Eichornia crassipes ash, which was ineffective in vitro, offered some protection to seeds in soil against pre-emergence rot. The study demonstrates potentials of ash samples from tropical plants in control of S. rolfsii on wheat.

Development of novel ash hybrids to introgress resistance to emerald ash borer into north American ash species

Treesearch

Jennifer L. Koch; David W. Carey; Mary E. Mason

2008-01-01

Currently, there is no evidence that any of the native North American ash species have any resistance to the emerald ash borer (EAB). This means that the entire ash resource of the eastern United States and Canada is at risk of loss due to EAB. In contrast, outbreaks of EAB in Asian ash species are rare and appear to be isolated responses to stress (Bauer et al. 2005,...

Large-magnitude Middle Ordovician volcanic ash falls in North America and Europe: Dimensions, emplacement and post-emplacement characteristics

USGS Publications Warehouse

Huff, W.D.; Kolata, Dennis R.; Bergstrom, Stig M.; Zhang, Y.-S.

1996-01-01

Middle Ordovician K-bentonites represent some of the largest known fallout ash deposits in the Phanerozoic Era. They cover minimally 2.2 ?? 106 km2 in eastern North America and 6.9 ?? 105 km2 in northwestern Europe, and represents the coeval accumulation of plinian and co-ignimbrite ash on both Laurentia and Baltica during the closure of the Iapetus Ocean. The three most widespread beds are the Deicke and Millbrig K-bentonites in North America and the Kinnekulle K-bentonite in northwestern Europe. The vents were located near the Laurentian margin of Iapetus on an arc or microplate undergoing collision with Laurentia. The volume of ash preserved in the stratigraphic record converted to dense rock equivalent (DRE) of silicic magma is minimally estimated to be 943 km3 for the Deicke, 1509 km3 for the Millbrig and 972 km3 for the Kinnekulle. The Millbrig and Kinnekulle beds are coeval and possibly equivalent, yielding a combined DRE volume of nearly 2500 km3. Some unknown but probably large amount of additional ash fell into oceanic regions of the Iapetus, but these areas became subducted and the ash is not preserved in the geologic record. The symmetry of the thickness contours is suggestive that one or more ash clouds interacting with equatorial stratospheric and tropospheric wind patterns dispersed pyroclastic material to both the northwest and southeast in terms of Ordovician paleogeography. Based on grain size measurements and thickness/area1/2 plots we conclude the three beds were each formed from co-ignimbrite or possibly phreatoplinian eruption columns. Analyses of melt inclusions in primary quartz crystals indicate the parental magma contained approximately 4% dissolved water at the time of the eruption. This water provided the explosive energy during the initial gas thrust phase. The implied fragmentation pressure on the magma would have reduced much of the ejecta to small particles, forming a deposit composed largely of single crystals and glassy dust. Conversion of the ash to K-bentonite resulted in a mass loss of approximately 35%, mostly in the form of Si with lesser amounts of Na and K.

Volcanic plume and bomb field masses from thermal infrared camera imagery

NASA Astrophysics Data System (ADS)

Harris, A. J. L.; Delle Donne, D.; Dehn, J.; Ripepe, M.; Worden, A. K.

2013-03-01

Masses erupted during normal explosions at Stromboli volcano (Italy) are notoriously difficult to measure. We present a method that uses thermal infrared video for cooling bomb fields to obtain the total power emitted by all hot particles emitted during an explosion. A given mass of magma (M) will emit a finite amount of thermal power, defined by M cp(Te-T0), cp and Te being magma specific heat capacity and temperature, and T0 being ambient temperature. We use this relation to convert the total power emitted by the bomb field to the mass required to generate that power. To do this we extract power flux curves for the field and integrate this through time to obtain total power (E). This is used to estimate mass (Q) in Q=E/cp(Te-T0). When applied to individual bombs we obtain masses of between 1 and 9 kg per bomb, or a volume of 970 and 6500 cm3. These volumes equate to spheres with diameters 12 and 27 cm. For the entire bomb field we obtain volumes of 7-28 m3. We calculate masses for 32 eruptions and obtain typical bomb masses of between 103 and 104 kg per eruption. In addition, we estimate that between 102 and 103 kg of gas and ash are emitted as part of a mixed plume of bombs, gas and ash. We identify two types of eruption on the basis of the erupted bomb masses and the ratio of the plume's gas-and-ash component to the bomb component. The first type is bomb-dominated, is characterized by bomb masses of 104 kg and has ash-gas/ bomb ratios of ˜0.02. The second type is ash-and-gas dominated, is characterized by erupted bomb masses of 103 kg and has ash-gas/bomb ratios of around one, and as high as two. There is no correlation between the quantity of bombs and quantity of gas-ash erupted. In addition, while source pressure for each explosion correlates with the quantity of gas and ash erupted, the mass of bombs emitted varies independently of pressure.

Critical quench dynamics in confined systems.

PubMed

Collura, Mario; Karevski, Dragi

2010-05-21

We analyze the coherent quantum evolution of a many-particle system after slowly sweeping a power-law confining potential. The amplitude of the confining potential is varied in time along a power-law ramp such that the many-particle system finally reaches or crosses a critical point. Under this protocol we derive general scaling laws for the density of excitations created during the nonadiabatic sweep of the confining potential. It is found that the mean excitation density follows an algebraic law as a function of the sweeping rate with an exponent that depends on the space-time properties of the potential. We confirm our scaling laws by first order adiabatic calculation and exact results on the Ising quantum chain with a varying transverse field.

Differential utilization of ash phloem by emerald ash borer larvae: Ash species and larval stage effects

Treesearch

Yigen Chen; Michael D. Ulyshen; Therese M. Poland

2012-01-01

Two experiments were performed to determine the extent to which ash species (black, green and white) and larval developmental stage (second, third and fourth instar) affect the efficiency of phloem amino acid utilization by emerald ash borer (EAB) Agrilus planipennis Fairmaire (Coleoptera: Buprestidae) larvae. EAB larvae generally utilized green ash...

Emerald ash borer biocontrol in ash saplings: the potential for early stage recovery of North American ash

USDA-ARS?s Scientific Manuscript database

In many parts of North America, ash stands have been reduced by the emerald ash borer (Agrilus planipennis) invasion to a few surviving mature trees and young basal sprouts, saplings, and seedlings. Without a seed bank, ash tree recovery will require survival and maturation of these younger cohorts...

Ecological and Topographic Features of Volcanic Ash-Influenced Forest Soils

Treesearch

Mark Kimsey; Brian Gardner; Alan Busacca

2007-01-01

Volcanic ash distribution and thickness were determined for a forested region of north-central Idaho. Mean ash thickness and multiple linear regression analyses were used to model the effect of environmental variables on ash thickness. Slope and slope curvature relationships with volcanic ash thickness varied on a local spatial scale across the study area. Ash...