Effectiveness of an automatic manual wheelchair braking system in the prevention of falls.

PubMed

Martorello, Laura; Swanson, Edward

2006-01-01

The purpose of this study was to evaluate the effectiveness of an automatic manual wheelchair braking system in the reduction of falls for patients at high risk of falls while transferring to and from a manual wheelchair. The study design was a normative survey carried out through the use of a written questionnaire sent to 60 skilled nursing facilities to collect data from the medical charts, which identified patients at high risk for falls who used an automatic wheelchair braking system. The facilities participating in the study identified a frequency of falls of high-risk patients while transferring to and from the wheelchair ranging from 2 to 10 per year, with a median fall rate per facility of 4 falls. One year after the installation of the automatic wheelchair braking system, participating facilities demonstrated a reduction of zero to three falls during transfers by high-risk patients, with a median fall rate of zero falls. This represents a statistically significant reduction of 78% in the fall rate of high-risk patients while transferring to and from the wheelchair, t (18) = 6.39, p < .0001. Incident reports of falls to and from manual wheelchairs were reviewed retrospectively for a 1-year period. This study suggests that high-risk fallers transferring to or from manual wheelchairs sustained significantly fewer falls when the Steddy Mate automatic braking system for manual wheelchairs was installed. The application of the automatic braking system allows clients, families/caregivers, and facility personnel an increased safety factor for the reduction of falls from the wheelchair.

49 CFR 236.507 - Brake application; full service.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards § 236.507 Brake application; full service. The automatic train stop or train control apparatus shall, when operated, cause a full service...

49 CFR 236.507 - Brake application; full service.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards § 236.507 Brake application; full service. The automatic train stop or train control apparatus shall, when operated, cause a full service...

Accelerometer-controlled automatic braking system

NASA Technical Reports Server (NTRS)

Dreher, R. C.; Sleeper, R. K.; Nayadley, J. R., Sr.

1973-01-01

Braking system, which employs angular accelerometer to control wheel braking and results in low level of tire slip, has been developed and tested. Tests indicate that system is feasible for operations on surfaces of different slipperinesses. System restricts tire slip and is capable of adapting to rapidly-changing surface conditions.

The unbalanced signal measuring of automotive brake drum

NASA Astrophysics Data System (ADS)

Wang, Xiao-Dong; Ye, Sheng-Hua; Zhang, Bang-Cheng

2005-04-01

For the purpose of the research and development of automatic balancing system by mass removing, the dissertation deals with the measuring method of the unbalance signal, the design the automatic balance equipment and the software. This paper emphases the testing system of the balancer of automotive brake drum. The paper designs the band-pass filter product with favorable automatic follow of electronic product, and with favorable automatic follow capability, filtration effect and stability. The system of automatic balancing system by mass removing based on virtual instrument is designed in this paper. A lab system has been constructed. The results of contrast experiments indicate the notable effect of 1-plane automatic balance and the high precision of dynamic balance, and demonstrate the application value of the system.

Operator’s Manual. Prototype Heavy Rescue/Fire Fighting Vehicle

DTIC Science & Technology

1980-09-01

system for emergency operation if pressure is lost in either parking or service brake systems . The system is operational automatically and is...controlled by the foot treadle ’sive. It will provide for TWO full brake applications and ONE release. ELECTRICAL SYSTEM A dual battery system is utilized for...cleaner. * Lubricate chassis. . Repack wheel bearings. . Inspect brake system and adjust brakes . . Replace fuel filter. . Check high and low idle.

Braking System for Wind Turbines

NASA Technical Reports Server (NTRS)

Krysiak, J. E.; Webb, F. E.

1987-01-01

Operating turbine stopped smoothly by fail-safe mechanism. Windturbine braking systems improved by system consisting of two large steel-alloy disks mounted on high-speed shaft of gear box, and brakepad assembly mounted on bracket fastened to top of gear box. Lever arms (with brake pads) actuated by spring-powered, pneumatic cylinders connected to these arms. Springs give specific spring-loading constant and exert predetermined load onto brake pads through lever arms. Pneumatic cylinders actuated positively to compress springs and disengage brake pads from disks. During power failure, brakes automatically lock onto disks, producing highly reliable, fail-safe stops. System doubles as stopping brake and "parking" brake.

30 CFR 75.523-3 - Automatic emergency-parking brakes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... despite any contraction of brake parts, exhaustion of any non-mechanical source of energy, or leakage; and... of any non-mechanical source of energy, or leakage. (e) The brake systems required by paragraphs (a...

30 CFR 75.523-3 - Automatic emergency-parking brakes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... despite any contraction of brake parts, exhaustion of any non-mechanical source of energy, or leakage; and... of any non-mechanical source of energy, or leakage. (e) The brake systems required by paragraphs (a...

30 CFR 75.523-3 - Automatic emergency-parking brakes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... despite any contraction of brake parts, exhaustion of any non-mechanical source of energy, or leakage; and... of any non-mechanical source of energy, or leakage. (e) The brake systems required by paragraphs (a...

30 CFR 77.1401 - Automatic controls and brakes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic controls and brakes. 77.1401 Section... MINES Personnel Hoisting § 77.1401 Automatic controls and brakes. Hoists and elevators shall be equipped with overspeed, overwind, and automatic stop controls and with brakes capable of stopping the elevator...

30 CFR 75.1404 - Automatic brakes; speed reduction gear.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic brakes; speed reduction gear. 75.1404... Automatic brakes; speed reduction gear. [Statutory Provisions] Each locomotive and haulage car used in an... permit automatic brakes, locomotives and haulage cars shall be subject to speed reduction gear, or other...

30 CFR 75.1404 - Automatic brakes; speed reduction gear.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Automatic brakes; speed reduction gear. 75.1404... Automatic brakes; speed reduction gear. [Statutory Provisions] Each locomotive and haulage car used in an... permit automatic brakes, locomotives and haulage cars shall be subject to speed reduction gear, or other...

30 CFR 75.523-3 - Automatic emergency-parking brakes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic emergency-parking brakes. 75.523-3...-3 Automatic emergency-parking brakes. (a) Except for personnel carriers, rubber-tired, self... with automatic emergency-parking brakes in accordance with the following schedule. (1) On and after May...

30 CFR 75.523-3 - Automatic emergency-parking brakes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Automatic emergency-parking brakes. 75.523-3...-3 Automatic emergency-parking brakes. (a) Except for personnel carriers, rubber-tired, self... with automatic emergency-parking brakes in accordance with the following schedule. (1) On and after May...

49 CFR 393.43 - Breakaway and emergency braking.

Code of Federal Regulations, 2010 CFR

2010-10-01

... protection system. Every motor vehicle, if used to tow a trailer equipped with brakes, shall be equipped with... protection valve or similar device shall operate automatically when the air pressure on the towing vehicle is... brake systems installed on towed vehicles shall be so designed, by the use of “no-bleed-back” relay...

49 CFR 393.43 - Breakaway and emergency braking.

Code of Federal Regulations, 2011 CFR

2011-10-01

... protection system. Every motor vehicle, if used to tow a trailer equipped with brakes, shall be equipped with... protection valve or similar device shall operate automatically when the air pressure on the towing vehicle is... brake systems installed on towed vehicles shall be so designed, by the use of “no-bleed-back” relay...

30 CFR 56.19006 - Automatic hoist braking devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic hoist braking devices. 56.19006 Section 56.19006 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoists § 56.19006 Automatic hoist braking devices. Automatic hoists shall be provided with devices...

30 CFR 57.19006 - Automatic hoist braking devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic hoist braking devices. 57.19006 Section 57.19006 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoists § 57.19006 Automatic hoist braking devices. Automatic hoists shall be provided with devices...

Detection technology research on the one-way clutch of automatic brake adjuster

NASA Astrophysics Data System (ADS)

Jiang, Wensong; Luo, Zai; Lu, Yi

2013-10-01

In this article, we provide a new testing method to evaluate the acceptable quality of the one-way clutch of automatic brake adjuster. To analysis the suitable adjusting brake moment which keeps the automatic brake adjuster out of failure, we build a mechanical model of one-way clutch according to the structure and the working principle of one-way clutch. The ranges of adjusting brake moment both clockwise and anti-clockwise can be calculated through the mechanical model of one-way clutch. Its critical moment, as well, are picked up as the ideal values of adjusting brake moment to evaluate the acceptable quality of one-way clutch of automatic brake adjuster. we calculate the ideal values of critical moment depending on the different structure of one-way clutch based on its mechanical model before the adjusting brake moment test begin. In addition, an experimental apparatus, which the uncertainty of measurement is ±0.1Nm, is specially designed to test the adjusting brake moment both clockwise and anti-clockwise. Than we can judge the acceptable quality of one-way clutch of automatic brake adjuster by comparing the test results and the ideal values instead of the EXP. In fact, the evaluation standard of adjusting brake moment applied on the project are still using the EXP provided by manufacturer currently in China, but it would be unavailable when the material of one-way clutch changed. Five kinds of automatic brake adjusters are used in the verification experiment to verify the accuracy of the test method. The experimental results show that the experimental values of adjusting brake moment both clockwise and anti-clockwise are within the ranges of theoretical results. The testing method provided by this article vividly meet the requirements of manufacturer's standard.

30 CFR 75.1403-4 - Criteria-Automatic elevators.

Code of Federal Regulations, 2010 CFR

2010-07-01

... appropriate on automatic elevators which will automatically shut-off the power and apply the brakes in the... telephone or other effective communication system by which aid or assistance can be obtained promptly. ...

Wheelchair ergometer. Development of a prototype with electronic braking.

PubMed

Forchheimer, F; Lundberg, A

1986-01-01

A new wheelchair ergometer is described, which compensates for the pulsating character of the work by an automatic control system. This makes it possible to maintain a constant level of power during wheelchair work. An automatic control system has been integrated in an electronically braked bicycle ergometer, and a pedal unit from Rodby Electronic bicycle ergometer RE 820 has been coupled to a modified test wheelchair. With this device, the physical working capacity during submaximal circumstances can be tested in handicapped persons.

An air brake model for longitudinal train dynamics studies

NASA Astrophysics Data System (ADS)

Wei, Wei; Hu, Yang; Wu, Qing; Zhao, Xubao; Zhang, Jun; Zhang, Yuan

2017-04-01

Experience of heavy haul train operation shows that heavy haul train fatigue fracture of coupler and its related components, even the accidents are caused by excessive coupler force. The most economical and effective method to study on train longitudinal impulse by reducing the coupler force is simulation method. The characteristics of train air brake system is an important excitation source for the study of longitudinal impulse. It is very difficult to obtain the braking characteristic by the test method, a better way to get the input parameters of the excitation source in the train longitudinal dynamics is modelling the train air brake system. In this paper, the air brake system model of integrated system of air brake and longitudinal dynamics is introduced. This introduce is focus on the locomotive automatic brake valve and vehicle distribution valve model, and the comparative analysis of the simulation and test results of the braking system is given. It is proved that the model can predict the characteristics of train braking system. This method provides a good solution for the excitation source of longitudinal dynamic analysis system.

Emergency escape system uses self-braking mechanism on fixed cable

NASA Technical Reports Server (NTRS)

Billings, C. R.; Mc Daris, R. A.; Mc Gough, J. T.; Neal, P. F.

1966-01-01

Slide-wire system with a twist level slide device incorporates automatic descent and braking for the safe and rapid evacuation of personnel from tall structures. This device is used on any tall structure that might require emergency evacuation. It is also used to transfer materials and equipment.

The Effect of a Low-Speed Automatic Brake System Estimated From Real Life Data

PubMed Central

Isaksson-Hellman, Irene; Lindman, Magdalena

2012-01-01

A substantial part of all traffic accidents involving passenger cars are rear-end collisions and most of them occur at low speed. Auto Brake is a feature that has been launched in several passenger car models during the last few years. City Safety is a technology designed to help the driver mitigate, and in certain situations avoid, rear-end collisions at low speed by automatically braking the vehicle. Studies have been presented that predict promising benefits from these kinds of systems, but few attempts have been made to show the actual effect of Auto Brake. In this study, the effect of City Safety, a standard feature on the Volvo XC60 model, is calculated based on insurance claims data from cars in real traffic crashes in Sweden. The estimated claim frequency of rear-end frontal collisions measured in claims per 1,000 insured vehicle years was 23% lower for the City Safety equipped XC60 model than for other Volvo models without the system. PMID:23169133

The effect of a low-speed automatic brake system estimated from real life data.

PubMed

Isaksson-Hellman, Irene; Lindman, Magdalena

2012-01-01

A substantial part of all traffic accidents involving passenger cars are rear-end collisions and most of them occur at low speed. Auto Brake is a feature that has been launched in several passenger car models during the last few years. City Safety is a technology designed to help the driver mitigate, and in certain situations avoid, rear-end collisions at low speed by automatically braking the vehicle.Studies have been presented that predict promising benefits from these kinds of systems, but few attempts have been made to show the actual effect of Auto Brake. In this study, the effect of City Safety, a standard feature on the Volvo XC60 model, is calculated based on insurance claims data from cars in real traffic crashes in Sweden. The estimated claim frequency of rear-end frontal collisions measured in claims per 1,000 insured vehicle years was 23% lower for the City Safety equipped XC60 model than for other Volvo models without the system.

30 CFR 75.1909 - Nonpermissible diesel-powered equipment; design and performance requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... rail-mounted equipment, must be provided with a parking brake that holds the fully loaded equipment... work platforms must be provided with a means to ensure that the parking braking system is released... requirements of § 75.1908(a) must be provided with an automatic fire suppression system meeting the...

30 CFR 75.1909 - Nonpermissible diesel-powered equipment; design and performance requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... rail-mounted equipment, must be provided with a parking brake that holds the fully loaded equipment... work platforms must be provided with a means to ensure that the parking braking system is released... requirements of § 75.1908(a) must be provided with an automatic fire suppression system meeting the...

49 CFR 571.122 - Standard No. 122; Motorcycle brake systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... transmission of signals in the motorcycle's ABS system. (b) To permit function checking, the warning lamp shall... CFR 571.101). S5.2Durability. S5.2.1Compensation for wear. Wear of the brakes shall be compensated for by means of a system of automatic or manual adjustment. S5.2.2Notice of wear. The friction material...

49 CFR 571.122 - Standard No. 122; Motorcycle brake systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... transmission of signals in the motorcycle's ABS system. (b) To permit function checking, the warning lamp shall... CFR 571.101). S5.2Durability. S5.2.1Compensation for wear. Wear of the brakes shall be compensated for by means of a system of automatic or manual adjustment. S5.2.2Notice of wear. The friction material...

Engineering Design Handbook: Analysis and Design of Automotive Brake Systems.

DTIC Science & Technology

1976-12-01

Highway Safety Research institute, Uni- versity of Michigan, September 15, 1972. IF’vn = (I - #)WT’,Kk I1, J. E. Bernard , et al,, A Computer Based...systems involve the reduction in brake line pres- 4. E. L. Cornwell , "Automatic Load-Sensitive Air sure for a given pedal force, the pedal force/de

49 CFR 236.830 - Time, acknowledging.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.830 Time, acknowledging. As applied to an intermittent automatic train stop system, a predetermined time within which an automatic brake application may be forestalled by means of the acknowledging device. ...

49 CFR Appendix B to Part 232 - Part 232 Prior to May 31, 2001 as Clarified Effective April 10, 2002

Code of Federal Regulations, 2010 CFR

2010-10-01

... coupled to train, after which, an automatic brake application and release test of airbrakes on rear car... closing angle cocks for cutting off one or more cars from the rear end of train, automatic air brake must... automatic air brake must not be depended upon to hold a locomotive, cars or train, when standing on a grade...

49 CFR Appendix B to Part 232 - Part 232 Prior to May 31, 2001 as Clarified Effective April 10, 2002

Code of Federal Regulations, 2011 CFR

2011-10-01

... coupled to train, after which, an automatic brake application and release test of airbrakes on rear car... closing angle cocks for cutting off one or more cars from the rear end of train, automatic air brake must... automatic air brake must not be depended upon to hold a locomotive, cars or train, when standing on a grade...

Implementation Of Fuzzy Automated Brake Controller Using TSK Algorithm

NASA Astrophysics Data System (ADS)

Mittal, Ruchi; Kaur, Magandeep

2010-11-01

In this paper an application of Fuzzy Logic for Automatic Braking system is proposed. Anti-blocking system (ABS) brake controllers pose unique challenges to the designer: a) For optimal performance, the controller must operate at an unstable equilibrium point, b) Depending on road conditions, the maximum braking torque may vary over a wide range, c) The tire slippage measurement signal, crucial for controller performance, is both highly uncertain and noisy. A digital controller design was chosen which combines a fuzzy logic element and a decision logic network. The controller identifies the current road condition and generates a command braking pressure signal Depending upon the speed and distance of train. This paper describes design criteria, and the decision and rule structure of the control system. The simulation results present the system's performance depending upon the varying speed and distance of the train.

Automatic Brake Slack Adjusters on Transit Buses

DOT National Transportation Integrated Search

1985-04-01

The purpose of this report is to provide transit bus agencies with current information on automatic brake slack adjusters. Rather than a comprehensive statistical survey, this report is intended to provide an overview of the states of automatic slack...

49 CFR 236.739 - Device, acknowledging.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.739... locomotive equipped with an automatic train stop or train control device, an automatic brake application can be forestalled, or by means of which, on a locomotive equipped with an automatic cab signal device...

Rendezvous terminal phase automatic braking sequencing and targeting. [for space shuttle orbiter

NASA Technical Reports Server (NTRS)

Kachmar, P. M.

1973-01-01

The purpose of the rendezvous terminal phase braking program is to provide the means of automatically bringing the primary orbiter within desired station keeping boundaries relative to the target satellite. A detailed discussion is presented on the braking program and its navigation, targeting, and guidance functions.

The research of automatic speed control algorithm based on Green CBTC

NASA Astrophysics Data System (ADS)

Lin, Ying; Xiong, Hui; Wang, Xiaoliang; Wu, Youyou; Zhang, Chuanqi

2017-06-01

Automatic speed control algorithm is one of the core technologies of train operation control system. It’s a typical multi-objective optimization control algorithm, which achieve the train speed control for timing, comfort, energy-saving and precise parking. At present, the train speed automatic control technology is widely used in metro and inter-city railways. It has been found that the automatic speed control technology can effectively reduce the driver’s intensity, and improve the operation quality. However, the current used algorithm is poor at energy-saving, even not as good as manual driving. In order to solve the problem of energy-saving, this paper proposes an automatic speed control algorithm based on Green CBTC system. Based on the Green CBTC system, the algorithm can adjust the operation status of the train to improve the efficient using rate of regenerative braking feedback energy while ensuring the timing, comfort and precise parking targets. Due to the reason, the energy-using of Green CBTC system is lower than traditional CBTC system. The simulation results show that the algorithm based on Green CBTC system can effectively reduce the energy-using due to the improvement of the using rate of regenerative braking feedback energy.

Piezoelectric-hydraulic pump based band brake actuation system for automotive transmission control

NASA Astrophysics Data System (ADS)

Kim, Gi-Woo; Wang, K. W.

2007-04-01

The actuation system of friction elements (such as band brakes) is essential for high quality operations in modern automotive automatic transmissions (in short, ATs). The current band brake actuation system consists of several hydraulic components, including the oil pump, the regulating valve and the control valves. In general, it has been recognized that the current AT band brake actuation system has many limitations. For example, the oil pump and valve body are relatively heavy and complex. Also, the oil pumps induce inherently large drag torque, which affects fuel economy. This research is to overcome these problems of the current system by exploring the utilization of a hybrid type piezo-hydraulic pump device for AT band brake control. This new actuating system integrates a piezo-hydraulic pump to the input of the band brake. Compared with the current systems, this new actuator features much simpler structure, smaller size, and lower weight. This paper describes the development, design and fabrication of the new stand-alone prototype actuator for AT band brake control. An analytical model is developed and validated using experimental data. Performance tests on the hardware and system simulations utilizing the validated model are performed to characterize the new prototype actuator. It is predicted that with increasing of accumulator pressure and driving frequency, the proposed prototype actuating system will satisfy the band brake requirement for AT shift control.

49 CFR 236.747 - Forestall.

Code of Federal Regulations, 2011 CFR

2011-10-01

... OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.747 Forestall. As applied to an automatic train stop or train control device, to prevent an automatic brake application by operation of an acknowledging device or by manual control of the speed of the train. ...

49 CFR 236.747 - Forestall.

Code of Federal Regulations, 2010 CFR

2010-10-01

... OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.747 Forestall. As applied to an automatic train stop or train control device, to prevent an automatic brake application by operation of an acknowledging device or by manual control of the speed of the train. ...

Motorized control for mirror mount apparatus

DOEpatents

Cutburth, Ronald W.

1989-01-01

A motorized control and automatic braking system for adjusting mirror mount apparatus is disclosed. The motor control includes a planetary gear arrangement to provide improved pitch adjustment capability while permitting a small packaged design. The motor control for mirror mount adjustment is suitable for laser beam propagation applications. The brake is a system of constant contact, floating detents which engage the planetary gear at selected between-teeth increments to stop rotation instantaneously when the drive motor stops.

30 CFR 56.10004 - Brakes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Aerial Tramways § 56.10004 Brakes. Positive-action-type brakes and devices which apply the brakes automatically in the event of a power... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Brakes. 56.10004 Section 56.10004 Mineral...

30 CFR 57.10004 - Brakes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Aerial Tramways § 57.10004 Brakes. Positive-action-type brakes and devices which apply the brakes automatically in the event of a power... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Brakes. 57.10004 Section 57.10004 Mineral...

49 CFR 236.701 - Application, brake; full service.

Code of Federal Regulations, 2010 CFR

2010-10-01

... a split reduction in brake pipe pressure at a service rate until maximum brake cylinder pressure is developed. As applied to an automatic or electro-pneumatic brake with speed governor control, an application other than emergency which develops the maximum brake cylinder pressure, as determined by the design of...

Exploratory field trial of motorcycle autonomous emergency braking (MAEB): Considerations on the acceptability of unexpected automatic decelerations.

PubMed

Savino, Giovanni; Pierini, Marco; Thompson, Jason; Fitzharris, Michael; Lenné, Michael G

2016-11-16

Autonomous emergency braking (AEB) acts to slow down a vehicle when an unavoidable impending collision is detected. In addition to documented benefits when applied to passenger cars, AEB has also shown potential when applied to motorcycles (MAEB). However, the feasibility of MAEB as practically applied to motorcycles in the real world is not well understood. In this study we performed a field trial involving 16 riders on a test motorcycle subjected to automatic decelerations, thus simulating MAEB activation. The tests were conducted along a rectilinear path at nominal speed of 40 km/h and with mean deceleration of 0.15 g (15% of full braking) deployed at random times. Riders were also exposed to one final undeclared brake activation with the aim of providing genuinely unexpected automatic braking events. Participants were consistently able to manage automatic decelerations of the vehicle with minor to moderate effort. Results of undeclared activations were consistent with those of standard runs. This study demonstrated the feasibility of a moderate automatic deceleration in a scenario of motorcycle travelling in a straight path, supporting the notion that the application of AEB on motorcycles is practicable. Furthermore, the proposed field trial can be used as a reference for future regulation or consumer tests in order to address safety and acceptability of unexpected automatic decelerations on a motorcycle.

Advanced Vehicle Control Systems Potential Tort Liability For Developers

DOT National Transportation Integrated Search

1993-12-01

AUTOMOBILE ACCIDENTS AVOIDED BECAUSE THE AUTOMATIC COLLISION AVOIDANCE SYSTEM APPLIES THE BRAKES, HIGHWAYS WHICH ACCOMMODATE MORE VEHICLES WITH FEWER ACCIDENTS, AND EVEN CARS WHICH ARE PILOTED ENTIRELY BY SOPHISTICATED ELECTRONIC SYSTEMS -- ALL OF TH...

Driving Control for Electric Power Assisted Wheelchair Based on Regenerative Brake

NASA Astrophysics Data System (ADS)

Seki, Hirokazu; Takahashi, Kazuki; Tadakuma, Susumu

This paper describes a novel safety driving control scheme for electric power assisted wheelchairs based on the regenerative braking system. “Electric power assisted wheelchair” which assists the driving force by electric motors is expected to be widely used as a mobility support system for elderly people and disabled people, however, the safe and secure driving performance especially on downhill roads must be further improved because electric power assisted wheelchairs have no braking devices. The proposed control system automatically switches the driving mode, from “assisting mode” to “braking mode”, based on the wheelchair's velocity and the declined angle and smoothly suppresses the wheelchair's acceleration based on variable duty ratio control in order to realize the safety driving and to improve the ride quality. Some experiments on the practical roads and subjective evaluation show the effectiveness of the proposed control system.

Roller Locking Brake

NASA Technical Reports Server (NTRS)

Vranish, John M.

1993-01-01

Roller locking brake is normally braking rotary mechanism allowing free rotation when electromagnet in mechanism energized. Well suited to robots and other machinery which automatic braking upon removal of electrical power required. More compact and reliable. Requires little electrical power to maintain free rotation and exhibits minimal buildup of heat.

EEG potentials predict upcoming emergency brakings during simulated driving

NASA Astrophysics Data System (ADS)

Haufe, Stefan; Treder, Matthias S.; Gugler, Manfred F.; Sagebaum, Max; Curio, Gabriel; Blankertz, Benjamin

2011-10-01

Emergency braking assistance has the potential to prevent a large number of car crashes. State-of-the-art systems operate in two stages. Basic safety measures are adopted once external sensors indicate a potential upcoming crash. If further activity at the brake pedal is detected, the system automatically performs emergency braking. Here, we present the results of a driving simulator study indicating that the driver's intention to perform emergency braking can be detected based on muscle activation and cerebral activity prior to the behavioural response. Identical levels of predictive accuracy were attained using electroencephalography (EEG), which worked more quickly than electromyography (EMG), and using EMG, which worked more quickly than pedal dynamics. A simulated assistance system using EEG and EMG was found to detect emergency brakings 130 ms earlier than a system relying only on pedal responses. At 100 km h-1 driving speed, this amounts to reducing the braking distance by 3.66 m. This result motivates a neuroergonomic approach to driving assistance. Our EEG analysis yielded a characteristic event-related potential signature that comprised components related to the sensory registration of a critical traffic situation, mental evaluation of the sensory percept and motor preparation. While all these components should occur often during normal driving, we conjecture that it is their characteristic spatio-temporal superposition in emergency braking situations that leads to the considerable prediction performance we observed.

EEG potentials predict upcoming emergency brakings during simulated driving.

PubMed

Haufe, Stefan; Treder, Matthias S; Gugler, Manfred F; Sagebaum, Max; Curio, Gabriel; Blankertz, Benjamin

2011-10-01

Emergency braking assistance has the potential to prevent a large number of car crashes. State-of-the-art systems operate in two stages. Basic safety measures are adopted once external sensors indicate a potential upcoming crash. If further activity at the brake pedal is detected, the system automatically performs emergency braking. Here, we present the results of a driving simulator study indicating that the driver's intention to perform emergency braking can be detected based on muscle activation and cerebral activity prior to the behavioural response. Identical levels of predictive accuracy were attained using electroencephalography (EEG), which worked more quickly than electromyography (EMG), and using EMG, which worked more quickly than pedal dynamics. A simulated assistance system using EEG and EMG was found to detect emergency brakings 130 ms earlier than a system relying only on pedal responses. At 100 km h(-1) driving speed, this amounts to reducing the braking distance by 3.66 m. This result motivates a neuroergonomic approach to driving assistance. Our EEG analysis yielded a characteristic event-related potential signature that comprised components related to the sensory registration of a critical traffic situation, mental evaluation of the sensory percept and motor preparation. While all these components should occur often during normal driving, we conjecture that it is their characteristic spatio-temporal superposition in emergency braking situations that leads to the considerable prediction performance we observed.

Linear-Force Actuators for Use on Shipboard Weapons and Cargo Elevators.

DTIC Science & Technology

1984-01-09

lock units an electro-mechanical brake is furnished so that when the unit stops at any position, its brake locks automatically , preventing any drift...NAME AND ADDRESS 12. REPORT DATE Naval Sea Systems Command (Code 56W4) f~nur 9, 1984 Washigton DC 03623. NUM4BER Of PAGES .9 ~, DC24 1.MONITORING...Hydraulic systems Weapons elevators a&. )TRACT (Couinsiu an ,evelee aide It nogceoy and fdentflr by block nunbov) "-Reports of hydraulic problems in

Asbestos Workshop: Sampling, Analysis, and Risk Assessment

DTIC Science & Technology

2012-03-01

coatings Vinyl/asbestos floor tile Automatic transmission components Clutch facings Disc brake pads Drum brake linings Brake blocks Commercial and...A naturally-occurring pliant and fibrous mineral with heat-resistant properties • Serpentine Class: joint compound,‘popcorn’ceilings, brake pads...fabrics, and is used in fire-resistant and insulating materials such as brake linings. The asbestos minerals include chrysotile (white asbestos) and

Analysis of separation test for automatic brake adjuster based on linear radon transformation

NASA Astrophysics Data System (ADS)

Luo, Zai; Jiang, Wensong; Guo, Bin; Fan, Weijun; Lu, Yi

2015-01-01

The linear Radon transformation is applied to extract inflection points for online test system under the noise conditions. The linear Radon transformation has a strong ability of anti-noise and anti-interference by fitting the online test curve in several parts, which makes it easy to handle consecutive inflection points. We applied the linear Radon transformation to the separation test system to solve the separating clearance of automatic brake adjuster. The experimental results show that the feature point extraction error of the gradient maximum optimal method is approximately equal to ±0.100, while the feature point extraction error of linear Radon transformation method can reach to ±0.010, which has a lower error than the former one. In addition, the linear Radon transformation is robust.

Construction Management Activities of Governmental Agencies in the New England Area During the Construction Phase.

DTIC Science & Technology

1980-02-01

automatic data exchange ... 56 There are currently 12 Data Systems available: I. Integrated Disbursing and Accounting (IDA) 2. Integrated Program Management...construction project progress through the use of a CPM scheduling and progress reporting system . It automatically generates invoices for payment and payment...posted on the project. Water will be drained daily from tanks of vehicle air brake systems . Rtigging, hooks, pendants and slings will be examined

Drive-By-Wire Technology

DTIC Science & Technology

2001-05-29

Symposium Intelligent Systems for the Objective Fleet uTransmission controls uSteering (both on-transmission and under-carriage) uBraking (service and...parking) uTransmission select uThrottle uOther Electromechanical Opportunities uTurret drives (elevation, traverse) uAutomatic propellant handling systems

49 CFR 571.123 - Standard No. 123; Motorcycle controls and displays.

Code of Federal Regulations, 2010 CFR

2010-10-01

... handgrip. If a motorcycle with an automatic clutch other than a scooter is equipped with a supplemental rear brake control, the control shall be located on the left handlebar. If a scooter with an automatic... equipped with self-proportioning or antilock braking devices utilizing a single control for front and rear...

Qualitative Maintenance Experience Handbook. P-3C/S-3A Supplement.

DTIC Science & Technology

1977-06-15

axle which automatically assists in disc alignment, a positive feature, in easing maintenance and preventing casual damage. Brake assemblies should...Reverse Of Removal Use brake tool to align brake discs . After Installation Actions: _ Bleed _ Rig _ Adjust X Service Lubricate - Boresight. _ Other...Hydraulic I Access Required: Test Equipment Required: Actions: 1. Check clearance of discs after brakes are put on. 2. Apply brakes . 8 ANALYST’S COMMENTS

29 CFR 1917.48 - Conveyors.

Code of Federal Regulations, 2010 CFR

2010-07-01

... using electrically released brakes shall be constructed so that the brakes cannot be released until power is applied, and so that the brakes are automatically engaged if the power fails or the operating... the operation of any power conveyor requires personnel to work in the immediate vicinity of the...

Advanced emergency braking under split friction conditions and the influence of a destabilising steering wheel torque

NASA Astrophysics Data System (ADS)

Tagesson, Kristoffer; Cole, David

2017-07-01

The steering system in most heavy trucks is such that it causes a destabilising steering wheel torque when braking on split friction, that is, different friction levels on the two sides of the vehicle. Moreover, advanced emergency braking systems are now mandatory in most heavy trucks, making vehicle-induced split friction braking possible. This imposes higher demands on understanding how the destabilising steering wheel torque affects the driver, which is the focus here. Firstly, an experiment has been carried out involving 24 subjects all driving a truck where automatic split friction braking was emulated. Secondly, an existing driver-vehicle model has been adapted and implemented to improve understanding of the observed outcome. A common conclusion drawn, after analysing results, is that the destabilising steering wheel torque only has a small effect on the motion of the vehicle. The underlying reason is a relatively slow ramp up of the disturbance in comparison to the observed cognitive delay amongst subjects; also the magnitude is low and initially suppressed by passive driver properties.

Commercial applications

NASA Technical Reports Server (NTRS)

Togai, Masaki

1990-01-01

Viewgraphs on commercial applications of fuzzy logic in Japan are presented. Topics covered include: suitable application area of fuzzy theory; characteristics of fuzzy control; fuzzy closed-loop controller; Mitsubishi heavy air conditioner; predictive fuzzy control; the Sendai subway system; automatic transmission; fuzzy logic-based command system for antilock braking system; fuzzy feed-forward controller; and fuzzy auto-tuning system.

Slip control for LIM propelled transit vehicles

NASA Astrophysics Data System (ADS)

Wallace, A. K.; Parker, J. H.; Dawson, G. E.

1980-09-01

Short stator linear induction motors, with an iron-backed aluminum sheet reaction rail and powered by a controlled inverter, have been selected as the propulsion system for transit vehicles in an intermediate capacity system (12-20,000 pphpd). The linear induction motor is capable of adhesion independent braking and acceleration levels which permit safe, close headways. In addition, simple control is possible allowing moving block automatic train control. This paper presents a slip frequency control scheme for the LIM. Experimental results for motoring and braking obtained from a test vehicle are also presented. These values are compared with theoretical predictions.

49 CFR 393.43 - Breakaway and emergency braking.

Code of Federal Regulations, 2012 CFR

2012-10-01

... independent of brake air, hydraulic, and other pressure, and independent of other controls, unless the braking... protection valve or similar device shall operate automatically when the air pressure on the towing vehicle is... to a fixed pressure which shall not be lower than 20 pounds per square inch nor higher than 45 pounds...

49 CFR 393.43 - Breakaway and emergency braking.

Code of Federal Regulations, 2013 CFR

2013-10-01

... independent of brake air, hydraulic, and other pressure, and independent of other controls, unless the braking... protection valve or similar device shall operate automatically when the air pressure on the towing vehicle is... to a fixed pressure which shall not be lower than 20 pounds per square inch nor higher than 45 pounds...

49 CFR 393.43 - Breakaway and emergency braking.

Code of Federal Regulations, 2014 CFR

2014-10-01

... independent of brake air, hydraulic, and other pressure, and independent of other controls, unless the braking... protection valve or similar device shall operate automatically when the air pressure on the towing vehicle is... to a fixed pressure which shall not be lower than 20 pounds per square inch nor higher than 45 pounds...

76 FR 55829 - Federal Motor Vehicle Safety Standards; Electronic Stability Control Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-09

.... Benefits of ESC Electronic stability control (ESC) systems use automatic computer- controlled braking of... demonstrated that these systems reduce fatal single-vehicle crashes of passenger cars by 55 percent and fatal... potential to prevent 56 percent of the fatal passenger car rollovers and 74 percent of the fatal LTV first...

49 CFR 236.553 - Seal, where required.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Rules and Instructions; Locomotives § 236.553 Seal, where required. Seal shall be maintained on any device other than brake-pipe cut-out cock (double-heading cock), by...

49 CFR 236.553 - Seal, where required.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Rules and Instructions; Locomotives § 236.553 Seal, where required. Seal shall be maintained on any device other than brake-pipe cut-out cock (double-heading cock), by...

Doppler extraction with a digital VCO

NASA Technical Reports Server (NTRS)

Starner, E. R.; Nossen, E. J.

1977-01-01

Digitally controlled oscillator in phased-locked loop may be useful for data communications systems, or may be modified to serve as information extraction component of microwave or optical system for collision avoidance or automatic braking. Instrument is frequency-synthesizing device with output specified precisely by digital number programmed into frequency register.

The MOD-OA 200 kilowatt wind turbine generator design and analysis report

NASA Astrophysics Data System (ADS)

Andersen, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-08-01

The project requirements, approach, system description, design requirements, design, analysis, system tests, installation safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the MOD-OA 200 kw wind turbine generator are discussed. The components, the rotor, driven train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electrical system, and control systems are presented. The rotor includes the blades, hub and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control and Dynamic loads and fatigue are analyzed.

The MOD-OA 200 kilowatt wind turbine generator design and analysis report

NASA Technical Reports Server (NTRS)

Andersen, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-01-01

The project requirements, approach, system description, design requirements, design, analysis, system tests, installation safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the MOD-OA 200 kw wind turbine generator are discussed. The components, the rotor, driven train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electrical system, and control systems are presented. The rotor includes the blades, hub and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control and Dynamic loads and fatigue are analyzed.

A novel technique for optimal integration of active steering and differential braking with estimation to improve vehicle directional stability.

PubMed

Mirzaeinejad, Hossein; Mirzaei, Mehdi; Rafatnia, Sadra

2018-06-11

This study deals with the enhancement of directional stability of vehicle which turns with high speeds on various road conditions using integrated active steering and differential braking systems. In this respect, the minimum usage of intentional asymmetric braking force to compensate the drawbacks of active steering control with small reduction of vehicle longitudinal speed is desired. To this aim, a new optimal multivariable controller is analytically developed for integrated steering and braking systems based on the prediction of vehicle nonlinear responses. A fuzzy programming extracted from the nonlinear phase plane analysis is also used for managing the two control inputs in various driving conditions. With the proposed fuzzy programming, the weight factors of the control inputs are automatically tuned and softly changed. In order to simulate a real-world control system, some required information about the system states and parameters which cannot be directly measured, are estimated using the Unscented Kalman Filter (UKF). Finally, simulations studies are carried out using a validated vehicle model to show the effectiveness of the proposed integrated control system in the presence of model uncertainties and estimation errors. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Automatic Train Operation Using Autonomic Prediction of Train Runs

NASA Astrophysics Data System (ADS)

Asuka, Masashi; Kataoka, Kenji; Komaya, Kiyotoshi; Nishida, Syogo

In this paper, we present an automatic train control method adaptable to disturbed train traffic conditions. The proposed method presumes transmission of detected time of a home track clearance to trains approaching to the station by employing equipment of Digital ATC (Automatic Train Control). Using the information, each train controls its acceleration by the method that consists of two approaches. First, by setting a designated restricted speed, the train controls its running time to arrive at the next station in accordance with predicted delay. Second, the train predicts the time at which it will reach the current braking pattern generated by Digital ATC, along with the time when the braking pattern transits ahead. By comparing them, the train correctly chooses the coasting drive mode in advance to avoid deceleration due to the current braking pattern. We evaluated the effectiveness of the proposed method regarding driving conditions, energy consumption and reduction of delays by simulation.

Designing of deployment sequence for braking and drift systems in atmosphere of Mars and Venus

NASA Astrophysics Data System (ADS)

Vorontsov, Victor

2006-07-01

Analysis of project development and space research using contact method, namely, by means of automatic descent modules and balloons shows that designing formation of entry, descent and landing (EDL) sequence and operation in the atmosphere are of great importance. This process starts at the very beginning of designing, has undergone a lot of iterations and influences processing of normal operation results. Along with designing of descent module systems, including systems of braking in the atmosphere, designing of flight operation sequence and trajectories of motion in the atmosphere is performed. As the entire operation sequence and transfer from one phase to another was correctly chosen, the probability of experiment success on the whole and efficiency of application of various systems vary. By now the most extensive experience of Russian specialists in research of terrestrial planets has been gained with the help of automatic interplanetary stations “Mars”, “Venera”, “Vega” which had descent modules and drifting in the atmosphere balloons. Particular interest and complicity of formation of EDL and drift sequence in the atmosphere of these planets arise from radically different operation conditions, in particular, strongly rarefied atmosphere of the one planet and extremely dense atmosphere of another. Consequently, this determines the choice of braking systems and their parameters and method of EDL consequence formation. At the same time there are general fundamental methods and designed research techniques that allowed taking general technical approach to designing of EDL and drift sequence in the atmosphere.

Influence of impact speed on head and brain injury outcome in vulnerable road user impacts to the car hood.

PubMed

Fredriksson, Rikard; Zhang, Liying; Boström, Ola; Yang, King

2007-10-01

EuroNCAP and regulations in Europe and Japan evaluate the pedestrian protection performance of cars. The test methods are similar and they all have requirements for the passive protection of the hood area at a pedestrian to car impact speed of 40 km/h. In Europe, a proposal for a second phase of the regulation mandates a brake-assist system along with passive requirements. The system assists the driver in optimizing the braking performance during panic braking, resulting in activation only when the driver brakes sufficiently. In a European study this was estimated to occur in about 50% of pedestrian accidents. A future system for brake assistance will likely include automatic braking, in response to a pre-crash sensor, to avoid or mitigate injuries of vulnerable road users. An important question is whether these systems will provide sufficient protection, or if a parallel, passive pedestrian protection system will be necessary. This study investigated the influence of impact speed on head and brain injury risk, in impacts to the carhood. One car model was chosen and a rigid adjustable plate was mounted under the hood. Free-flying headform impacts were carried out at 20 and 30 km/h head impact velocities at different under-hood distances, 20 to 100 mm; and were compared to earlier tests at 40 km/h. The EEVC WG17 adult pedestrian headform was used for non-rotating tests and a Hybrid III adult 50th percentile head was used for rotational tests where linear and rotational acceleration was measured. Data from the rotational tests was used as input to a validated finite element model of the human head, the Wayne State University Head Injury Model (WSUHIM). The model was utilized to assess brain injury risk and potential injury mechanism in a pedestrian-hood impact. Although this study showed that it was not necessarily true that a lower HIC value reduced the risk for brain injury, it appeared, for the tested car model, under-hood distances of 60 mm in 20 km/h and 80 mm in 30 km/h reduced head injury values for both skull fractures and brain injuries. An earlier study showed that the corresponding value for a test speed of 40 km/h is 100 mm. A 10 km/h reduction in head impact velocity, as in automatic braking, allowed 20 mm less under-hood clearance with maintained head protection of the vulnerable road user.

Data-based fault-tolerant control of high-speed trains with traction/braking notch nonlinearities and actuator failures.

PubMed

Song, Qi; Song, Yong-Duan

2011-12-01

This paper investigates the position and velocity tracking control problem of high-speed trains with multiple vehicles connected through couplers. A dynamic model reflecting nonlinear and elastic impacts between adjacent vehicles as well as traction/braking nonlinearities and actuation faults is derived. Neuroadaptive fault-tolerant control algorithms are developed to account for various factors such as input nonlinearities, actuator failures, and uncertain impacts of in-train forces in the system simultaneously. The resultant control scheme is essentially independent of system model and is primarily data-driven because with the appropriate input-output data, the proposed control algorithms are capable of automatically generating the intermediate control parameters, neuro-weights, and the compensation signals, literally producing the traction/braking force based upon input and response data only--the whole process does not require precise information on system model or system parameter, nor human intervention. The effectiveness of the proposed approach is also confirmed through numerical simulations.

49 CFR 571.102 - Standard No. 102; Transmission shift position sequence, starter interlock, and transmission...

Code of Federal Regulations, 2010 CFR

2010-10-01

... position. S3.1.2Transmission braking effect. In vehicles having more than one forward transmission gear... driver has activated the vehicle's propulsion system: (a) The engine may stop and restart automatically... activated the vehicle's propulsion system if the vehicle can meet the requirements specified in paragraphs...

49 CFR 238.119 - Rim-stamped straight-plate wheels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... input to the wheel during braking. (b) A rim-stamped straight-plate wheel shall not be used as a... that is periodically tread-braked for a short duration by automatic circuitry for the sole purpose of...

Leukocyte adhesion: High-speed cells with ABS.

PubMed

van der Merwe, P A

1999-06-03

In order to decide where to exit blood vessels and enter tissues, leukocytes roll along endothelial surfaces. Recent studies suggest that an 'automatic braking system' (ABS), involving selectin cell-adhesion molecules, enables leukocytes to roll at a fairly constant velocity despite large variations in blood flow rate.

Automatic braking system modification for the Advanced Transport Operating Systems (ATOPS) Transportation Systems Research Vehicle (TSRV)

NASA Technical Reports Server (NTRS)

Coogan, J. J.

1986-01-01

Modifications were designed for the B-737-100 Research Aircraft autobrake system hardware of the Advanced Transport Operating Systems (ATOPS) Program at Langley Research Center. These modifications will allow the on-board flight control computer to control the aircraft deceleration after landing to a continuously variable level for the purpose of executing automatic high speed turn-offs from the runway. A bread board version of the proposed modifications was built and tested in simulated stopping conditions. Test results, for various aircraft weights, turnoff speed, winds, and runway conditions show that the turnoff speeds are achieved generally with errors less than 1 ft/sec.

Techniques for Developing an Acquisition Strategy by Profiling Software Risks

DTIC Science & Technology

2006-08-01

Drivers...................................................................................... 13 Figure 8: BMW 745Li Software... BMW 745Li, shown in Figure 8, is a good illustration of the increasing software control of hardware systems in automobiles. Among the many features...roll stabilization, dynamic brake con- trol, coded drive-away protection, an adaptive automatic transmission, and iDrive systems. This list can be

Vehicle safety telemetry for automated highways

NASA Technical Reports Server (NTRS)

Hansen, G. R.

1977-01-01

The emphasis in current, automatic vehicle testing and diagnosis is primarily centered on the proper operation of the engine. Lateral and longitudinal guidance technologies, including speed control and headway sensing for collision avoidance, are reviewed. The principal guidance technique remains the buried wire. Speed control and headway sensing, even though they show the same basic elements in braking and fuel systems, are proceeding independently. The applications of on-board electronic and microprocessor techniques were investigated; each application (emission control, spark advance, or anti-slip braking) is being treated as an independent problem is proposed. A unified bus system of distributed processors for accomplishing the various functions and testing required for vehicles equipped to use automated highways.

76 FR 51468 - BMW of North America, LLC, a subsidiary of BMW AG, Receipt of Petition for Decision of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-18

...: (1) Automatic activation when the ignition (start) switch is turned to the ``on'' (``run'') position... of the parking brake, by applying the parking brake when the ignition is in the ``on'' (``run...

49 CFR 552.14 - Content of petition.

Code of Federal Regulations, 2012 CFR

2012-10-01

... for Expedited Rulemaking To Establish Dynamic Automatic Suppression System Test Procedures for Federal... petitioner shall provide the following information: (a) A set of proposed test procedures for S28.1, S28.2... unbelted occupant positions that are likely to occur during a frontal crash where pre-crash braking occurs...

49 CFR 552.14 - Content of petition.

Code of Federal Regulations, 2014 CFR

2014-10-01

... for Expedited Rulemaking To Establish Dynamic Automatic Suppression System Test Procedures for Federal... petitioner shall provide the following information: (a) A set of proposed test procedures for S28.1, S28.2... unbelted occupant positions that are likely to occur during a frontal crash where pre-crash braking occurs...

49 CFR 552.14 - Content of petition.

Code of Federal Regulations, 2013 CFR

2013-10-01

... for Expedited Rulemaking To Establish Dynamic Automatic Suppression System Test Procedures for Federal... petitioner shall provide the following information: (a) A set of proposed test procedures for S28.1, S28.2... unbelted occupant positions that are likely to occur during a frontal crash where pre-crash braking occurs...

Finite element fatigue analysis of rectangular clutch spring of automatic slack adjuster

NASA Astrophysics Data System (ADS)

Xu, Chen-jie; Luo, Zai; Hu, Xiao-feng; Jiang, Wen-song

2015-02-01

The failure of rectangular clutch spring of automatic slack adjuster directly affects the work of automatic slack adjuster. We establish the structural mechanics model of automatic slack adjuster rectangular clutch spring based on its working principle and mechanical structure. In addition, we upload such structural mechanics model to ANSYS Workbench FEA system to predict the fatigue life of rectangular clutch spring. FEA results show that the fatigue life of rectangular clutch spring is 2.0403×105 cycle under the effect of braking loads. In the meantime, fatigue tests of 20 automatic slack adjusters are carried out on the fatigue test bench to verify the conclusion of the structural mechanics model. The experimental results show that the mean fatigue life of rectangular clutch spring is 1.9101×105, which meets the results based on the finite element analysis using ANSYS Workbench FEA system.

Automated visual inspection of brake shoe wear

NASA Astrophysics Data System (ADS)

Lu, Shengfang; Liu, Zhen; Nan, Guo; Zhang, Guangjun

2015-10-01

With the rapid development of high-speed railway, the automated fault inspection is necessary to ensure train's operation safety. Visual technology is paid more attention in trouble detection and maintenance. For a linear CCD camera, Image alignment is the first step in fault detection. To increase the speed of image processing, an improved scale invariant feature transform (SIFT) method is presented. The image is divided into multiple levels of different resolution. Then, we do not stop to extract the feature from the lowest resolution to the highest level until we get sufficient SIFT key points. At that level, the image is registered and aligned quickly. In the stage of inspection, we devote our efforts to finding the trouble of brake shoe, which is one of the key components in brake system on electrical multiple units train (EMU). Its pre-warning on wear limitation is very important in fault detection. In this paper, we propose an automatic inspection approach to detect the fault of brake shoe. Firstly, we use multi-resolution pyramid template matching technology to fast locate the brake shoe. Then, we employ Hough transform to detect the circles of bolts in brake region. Due to the rigid characteristic of structure, we can identify whether the brake shoe has a fault. The experiments demonstrate that the way we propose has a good performance, and can meet the need of practical applications.

Braking mechanism is self actuating and bidirectional

NASA Technical Reports Server (NTRS)

Pizzo, J.

1966-01-01

Mechanism automatically applies a braking action on a moving item, in either direction of motion, immediately upon removal of the driving force and with no human operator involvement. This device would be useful wherever free movement is undesirable after an object has been guided into a precise position.

78 FR 29279 - Safety Standard for Carriages and Strollers

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-20

... incorporate automatic or assisted folding and unfolding mechanisms. B. Market Description The majority of... resulted in a bone fracture and head concussion. Parking brake problems related to parking brake failure or assembly resulted in 132 incidents, including eight injuries. Incidents typically occurred when the parking...

EVA Metro Sedan electric-propulsion system: test and evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reimers, E.

1979-09-01

The procedure and results of the performance evaluation of the EVA Metro Sedan (car No. 1) variable speed dc chopper motor drive and its three speed automatic transmission are presented. The propulsion system for a battery powered vehicle manufactured by Electric Vehicle Associates, Valley View, Ohio, was removed from the vehicle, mounted on the programmable electric dynamometer test facility and evaluated with the aid of a hp 3052A Data Acquisition System. Performance data for the automatic transmission, the solid state dc motor speed controller, and the dc motor in the continuous and pulsating dc power mode, as derived on themore » dynamometer test facility, as well as the entire propulsion system are given. This concept and the system's components were evaluated in terms of commercial applicability, maintainability, and energy utility to establish a design base for the further development of this system or similar propulsion drives. The propulsion system of the EVA Metro Sedan is powered by sixteen 6-volt traction batteries, Type EV 106 (Exide Battery Mfg. Co.). A thyristor controlled cable form Pulsomatic Mark 10 controller, actuated by a foot throttle, controls the voltage applied to a dc series field motor, rated at 10 hp at 3800 rpm (Baldor Electric Co.). Gear speed reduction to the wheel is accomplished by the original equipment three speed automatic transmission with torque converter (Renault 12 Sedan). The brake consists of a power-assisted, hydraulic braking system with front wheel disk and rear drum. An ability to recuperate electric energy with subsequent storage in the battery power supply is not provided.« less

AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT IX, AUTOMATIC TRANSMISSIONS--HYDRAULIC SYSTEM (PART I).

ERIC Educational Resources Information Center

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OIL FLOW WITHIN HYDRAULIC TRANSMISSIONS USED ON DIESEL POWERED VEHICLES. TOPICS ARE GENERAL DESCRIPTION, HYDRAULIC CIRCUITS, AND BRAKE HYDRAULIC CIRCUIT AND OPERATION. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL PROGRAMED TRAINING FILM "LEARNING ABOUT THE ALLISON…

29 CFR 1918.64 - Powered conveyors.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the brakes cannot be released until power is applied and the brakes are automatically engaged if the... provided for use in an emergency. Whenever the operation of any power conveyor requires personnel to work... the trimmer. (e) Grain trimmer power cable. Power cables between the deck control box and the grain...

75 FR 27926 - Special Conditions: Dassault Aviation Falcon Model 2000EX; Autobraking System

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-19

... Certificate (TC) No. A50NM to install an automatic braking system on the Falcon Model 2000EX airplane. This is... reference in TC No. A50NM or the applicable regulations in effect on the date of application for the change... ``original type certification basis.'' The regulations incorporated by reference in TC No. A50NM are as...

Computer controlled synchronous shifting of an automatic transmission

DOEpatents

Davis, Roy I.; Patil, Prabhakar B.

1989-01-01

A multiple forward speed automatic transmission produces its lowest forward speed ratio when a hydraulic clutch and hydraulic brake are disengaged and a one-way clutch connects a ring gear to the transmission casing. Second forward speed ratio results when the hydraulic clutch is engaged to connect the ring gear to the planetary carrier of a second gear set. Reverse drive and regenerative operation result when an hydraulic brake fixes the planetary and the direction of power flow is reversed. Various sensors produce signals representing the torque at the output of the transmission or drive wheels, the speed of the power source, and the hydraulic pressure applied to a clutch and brake. A control algorithm produces input data representing a commanded upshift, a commanded downshift, a commanded transmission output torque, and commanded power source speed. A microprocessor processes the inputs and produces a response to them in accordance with the execution of a control algorithm. Output or response signals cause selective engagement and disengagement of the clutch and brake at a rate that satisfies the requirements for a short gear ratio change and smooth torque transfer between the friction elements.

Development and Long-Term Verification of Stereo Vision Sensor System for Controlling Safety at Railroad Crossing

NASA Astrophysics Data System (ADS)

Hosotani, Daisuke; Yoda, Ikushi; Hishiyama, Yoshiyuki; Sakaue, Katsuhiko

Many people are involved in accidents every year at railroad crossings, but there is no suitable sensor for detecting pedestrians. We are therefore developing a ubiquitous stereo vision based system for ensuring safety at railroad crossings. In this system, stereo cameras are installed at the corners and are pointed toward the center of the railroad crossing to monitor the passage of people. The system determines automatically and in real-time whether anyone or anything is inside the railroad crossing, and whether anyone remains in the crossing. The system can be configured to automatically switch over to a surveillance monitor or automatically connect to an emergency brake system in the event of trouble. We have developed an original stereovision device and installed the remote controlled experimental system applied human detection algorithm in the commercial railroad crossing. Then we store and analyze image data and tracking data throughout two years for standardization of system requirement specification.

MOD-0A 200 kW wind turbine generator design and analysis report

NASA Astrophysics Data System (ADS)

Anderson, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-08-01

The design, analysis, and initial performance of the MOD-OA 200 kW wind turbine generator at Clayton, NM is documented. The MOD-OA was designed and built to obtain operation and performance data and experience in utility environments. The project requirements, approach, system description, design requirements, design, analysis, system tests, installation, safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the wind turbine are discussed. The design and analysis of the rotor, drive train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electricl system, and control systems are presented. The rotor includes the blades, hub, and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control are discussed. Systems analyses on dynamic loads and fatigue are presented.

MOD-0A 200 kW wind turbine generator design and analysis report

NASA Technical Reports Server (NTRS)

Anderson, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-01-01

The design, analysis, and initial performance of the MOD-OA 200 kW wind turbine generator at Clayton, NM is documented. The MOD-OA was designed and built to obtain operation and performance data and experience in utility environments. The project requirements, approach, system description, design requirements, design, analysis, system tests, installation, safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the wind turbine are discussed. The design and analysis of the rotor, drive train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electricl system, and control systems are presented. The rotor includes the blades, hub, and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control are discussed. Systems analyses on dynamic loads and fatigue are presented.

49 CFR 571.114 - Standard No. 114; Theft protection and rollaway prevention.

Code of Federal Regulations, 2010 CFR

2010-10-01

... pounds) or less with an automatic transmission that includes a “park” position shall be equipped with a... forward up a 10 percent grade and stop it with the service brakes. (b) Apply the parking brake (if present). (c) Move the gear selection control to “park.” (d) Note the vehicle position. (e) Release the parking...

49 CFR 571.114 - Standard No. 114; Theft protection and rollaway prevention.

Code of Federal Regulations, 2011 CFR

2011-10-01

... pounds) or less with an automatic transmission that includes a “park” position shall be equipped with a... forward up a 10 percent grade and stop it with the service brakes. (b) Apply the parking brake (if present). (c) Move the gear selection control to “park.” (d) Note the vehicle position. (e) Release the parking...

Nonlinear force feedback control of piezoelectric-hydraulic pump actuator for automotive transmission shift control

NASA Astrophysics Data System (ADS)

Kim, Gi-Woo; Wang, K. W.

2008-03-01

In recent years, researchers have investigated the feasibility of utilizing piezoelectric-hydraulic pump based actuation systems for automotive transmission controls. This new concept could eventually reduce the complexity, weight, and fuel consumption of the current transmissions. In this research, we focus on how to utilize this new approach on the shift control of automatic transmissions (AT), which generally requires pressure profiling for friction elements during the operation. To illustrate the concept, we will consider the 1--> 2 up shift control using band brake friction elements. In order to perform the actuation force tracking for AT shift control, nonlinear force feedback control laws are designed based on the sliding mode theory for the given nonlinear system. This paper will describe the modeling of the band brake actuation system, the design of the nonlinear force feedback controller, and simulation and experimental results for demonstration of the new concept.

Computer controllable synchronous shifting of an automatic transmission

DOEpatents

Davis, R.I.; Patil, P.B.

1989-08-08

A multiple forward speed automatic transmission produces its lowest forward speed ratio when a hydraulic clutch and hydraulic brake are disengaged and a one-way clutch connects a ring gear to the transmission casing. Second forward speed ratio results when the hydraulic clutch is engaged to connect the ring gear to the planetary carrier of a second gear set. Reverse drive and regenerative operation result when an hydraulic brake fixes the planetary and the direction of power flow is reversed. Various sensors produce signals representing the torque at the output of the transmission or drive wheels, the speed of the power source, and the hydraulic pressure applied to a clutch and brake. A control algorithm produces input data representing a commanded upshift, a commanded downshift, a commanded transmission output torque, and commanded power source speed. A microprocessor processes the inputs and produces a response to them in accordance with the execution of a control algorithm. Output or response signals cause selective engagement and disengagement of the clutch and brake at a rate that satisfies the requirements for a short gear ratio change and smooth torque transfer between the friction elements. 6 figs.

Applying visual attention theory to transportation safety research and design: evaluation of alternative automobile rear lighting systems.

PubMed

McIntyre, Scott E; Gugerty, Leo

2014-06-01

This field experiment takes a novel approach in applying methodologies and theories of visual search to the subject of conspicuity in automobile rear lighting. Traditional rear lighting research has not used the visual search paradigm in experimental design. It is our claim that the visual search design uniquely uncovers visual attention processes operating when drivers search the visual field that current designs fail to capture. This experiment is a validation and extension of previous simulator research on this same topic and demonstrates that detection of red automobile brake lamps will be improved if tail lamps are another color (in this test, amber) rather than the currently mandated red. Results indicate that when drivers miss brake lamp onset in low ambient light, RT and error are reduced in detecting the presence and absence of red brake lamps with multiple lead vehicles when tail lamps are not red compared to current rear lighting which mandates red tail lamps. This performance improvement is attributed to efficient visual processing that automatically segregates tail (amber) and brake (red) lamp colors into distractors and targets respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

Close up view of the pair of Rudder Pedals in ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Close up view of the pair of Rudder Pedals in the Commander's Satiation on the Flight Deck of the Orbiter Discovery. The rudder pedals command orbiter acceleration in yaw by positioning the rudder during atmospheric flight. However, because the flight control software automatically performs turn coordination during banking maneuvers, the rudder pedals are not operationally used during glided flight. It is not until after touchdown that the crew uses them for nose wheel steering during rollout. Depressing the upper portion of the rudder pedals provides braking. Differential braking may also be used for directional control during rollout. This view was take at Johnson Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Interactive design optimization of magnetorheological-brake actuators using the Taguchi method

NASA Astrophysics Data System (ADS)

Erol, Ozan; Gurocak, Hakan

2011-10-01

This research explored an optimization method that would automate the process of designing a magnetorheological (MR)-brake but still keep the designer in the loop. MR-brakes apply resistive torque by increasing the viscosity of an MR fluid inside the brake. This electronically controllable brake can provide a very large torque-to-volume ratio, which is very desirable for an actuator. However, the design process is quite complex and time consuming due to many parameters. In this paper, we adapted the popular Taguchi method, widely used in manufacturing, to the problem of designing a complex MR-brake. Unlike other existing methods, this approach can automatically identify the dominant parameters of the design, which reduces the search space and the time it takes to find the best possible design. While automating the search for a solution, it also lets the designer see the dominant parameters and make choices to investigate only their interactions with the design output. The new method was applied for re-designing MR-brakes. It reduced the design time from a week or two down to a few minutes. Also, usability experiments indicated significantly better brake designs by novice users.

29 CFR 1910.179 - Overhead and gantry cranes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... adequately guarded or isolated. (40) Fail-safe means a provision designed to automatically stop or safely... shall be capable of maintaining safe lowering speeds of rated loads. (ii) The control braking means... the crane operator. (viii) Automatic cranes shall be so designed that all motions shall fail-safe if...

40 CFR 86.1228-85 - Transmissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... than one minute in length shall be run with automatic transmissions in “Drive” and the wheels braked..., shall be run in a manner representative of in-use operation, and where appropriate, according to the... and idle modes longer than one minute in length shall be run with automatic transmissions in “Neutral...

Autonomous health management for PMSM rail vehicles through demagnetization monitoring and prognosis control.

PubMed

Niu, Gang; Jiang, Junjie; Youn, Byeng D; Pecht, Michael

2018-01-01

Autonomous vehicles are playing an increasingly importance in support of a wide variety of critical events. This paper presents a novel autonomous health management scheme on rail vehicles driven by permanent magnet synchronous motors (PMSMs). Firstly, the PMSMs are modeled based on first principle to deduce the initial profile of pneumatic braking (p-braking) force, then which is utilized for real-time demagnetization monitoring and degradation prognosis through similarity-based theory and generate prognosis-enhanced p-braking force strategy for final optimal control. A case study is conducted to demonstrate the feasibility and benefit of using the real-time prognostics and health management (PHM) information in vehicle 'drive-brake' control automatically. The results show that accurate demagnetization monitoring, degradation prognosis, and real-time capability for control optimization can be obtained, which can effectively relieve brake shoe wear. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Ubiquitous Stereo Vision for Controlling Safety on Platforms in Railroad Station

NASA Astrophysics Data System (ADS)

Yoda, Ikushi; Hosotani, Daisuke; Sakaue, Katushiko

Dozens of people are killed every year when they fall off of train platforms, making this an urgent issue to be addressed by the railroads, especially in the major cities. This concern prompted the present work that is now in progress to develop a Ubiquitous Stereo Vision based system for safety management at the edge of rail station platforms. In this approach, a series of stereo cameras are installed in a row on the ceiling that are pointed downward at the edge of the platform to monitor the disposition of people waiting for the train. The purpose of the system is to determine automatically and in real-time whether anyone or anything is in the danger zone at the very edge of the platform, whether anyone has actually fallen off the platform, or whether there is any sign of these things happening. The system could be configured to automatically switch over to a surveillance monitor or automatically connect to an emergency brake system in the event of trouble.

A model predictive speed tracking control approach for autonomous ground vehicles

NASA Astrophysics Data System (ADS)

Zhu, Min; Chen, Huiyan; Xiong, Guangming

2017-03-01

This paper presents a novel speed tracking control approach based on a model predictive control (MPC) framework for autonomous ground vehicles. A switching algorithm without calibration is proposed to determine the drive or brake control. Combined with a simple inverse longitudinal vehicle model and adaptive regulation of MPC, this algorithm can make use of the engine brake torque for various driving conditions and avoid high frequency oscillations automatically. A simplified quadratic program (QP) solving algorithm is used to reduce the computational time, and the approach has been applied in a 16-bit microcontroller. The performance of the proposed approach is evaluated via simulations and vehicle tests, which were carried out in a range of speed-profile tracking tasks. With a well-designed system structure, high-precision speed control is achieved. The system can robustly model uncertainty and external disturbances, and yields a faster response with less overshoot than a PI controller.

Motor vehicle technology:Mobility for prosperity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1985-01-01

This book presents the papers given at a conference on internal combustion engines for vehicles. Topics considered at the conference included combustion chambers, the lubrication of turbocharged engines, oil filters, fuel consumption, traffic control, crashworthiness, brakes, acceleration, unleaded gasoline, methanol fuels, pressure drop, safety regulations, tire vibration, detergents, fuel economy, ceramics in engines, steels, catalytic converters, fuel additives, heat exchangers, pump systems, emissions control, fuel injection systems, noise pollution control, natural gas fuels, assembly plant productivity, aerodynamics, torsion, electronics, and automatic transmissions.

49 CFR 570.58 - Electric brake system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Electric brake system. 570.58 Section 570.58... 10,000 Pounds § 570.58 Electric brake system. (a) Electric brake system integrity. The average brake... reading by the number of brakes and determine the brake amperage value. (b) Electric brake wiring...

49 CFR 570.58 - Electric brake system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 6 2014-10-01 2014-10-01 false Electric brake system. 570.58 Section 570.58... 10,000 Pounds § 570.58 Electric brake system. (a) Electric brake system integrity. The average brake... reading by the number of brakes and determine the brake amperage value. (b) Electric brake wiring...

49 CFR 570.58 - Electric brake system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 6 2012-10-01 2012-10-01 false Electric brake system. 570.58 Section 570.58... 10,000 Pounds § 570.58 Electric brake system. (a) Electric brake system integrity. The average brake... reading by the number of brakes and determine the brake amperage value. (b) Electric brake wiring...

Magnetic braking in Solar-type close binaries

NASA Astrophysics Data System (ADS)

Maceroni, C.; Rucinski, S. M.

In tidally locked binaries the angular momentum loss by magnetic braking affects the orbital period. While this effect is too small to be detected in individual systems, its signature can be seen in shape of the orbital period distribution of suitable samples. As a consequence information on the braking mechanisms can be obtained - at least in principle - from the analysis of the distributions, the main problems being the selection of a large and homogeneous sample of binaries and the appropriate treatment of the observational biases. New large databases of variable stars are becoming available as by-products of microlensing projects, which have the advantage of joining, for the first time, sample richness and homogeneity. We report the main results of the analysis of the eclipsing binaries in OGLE-I catalog, that contains several thousands variables detected in a pencil-beam search volume towards the Baade's Window. By means of an automatic filtering algorithm we extracted a sample of 74 detached, equal-mass, main-sequence binary stars with short orbital periods (i.e., in the range 0.19 < P < 8 days) and derived from the presently observed period distribution, after correction for selection effects, the expected slope of the braking law. The results suggest an AML braking law very close to the "saturated" one, with a very weak dependence on the period. However we are still far from constraining the precise value of the slope, because of the important role played by the observational bias.

Development of ATC for High Speed and High Density Commuter Line

NASA Astrophysics Data System (ADS)

Okutani, Tamio; Nakamura, Nobuyuki; Araki, Hisato; Irie, Shouji; Osa, Hiroki; Sano, Minoru; Ikeda, Keigo; Ozawa, Hiroyuki

A new ATC (Automatic Train Control) system has been developed with solutions to realize short train headway by assured braking utilizing digital data transmission via rails; the digital data for the ATP (Automatic Train Protection) function; and to achieve EMC features for both AC and DC sections. The DC section is of the unprecedented DC traction power supply system utilizing IGBT PWM converter at all DC substations. Within the AC section, train traction force is controlled by PWM converter/inverters. The carrier frequencies of the digital data signals and chopping frequency of PWM traction power converters on-board are decided via spectral analysis of noise up to degraded mode cases of equipment. Developed system was equipped to the Tukuba Express Line, new commuter line of Tokyo metropolitan area, and opened since Aug. 2005.

Switching sliding mode force tracking control of piezoelectric-hydraulic pump-based friction element actuation systems for automotive transmissions

NASA Astrophysics Data System (ADS)

Kim, Gi-Woo; Wang, K. W.

2009-08-01

In this study, a nonlinear sliding-mode controller is designed for force tracking of a piezoelectric-hydraulic pump (PHP)-based actuation system, which is developed to replace the current electro-hydraulic actuation systems for automatic transmission (AT) friction elements, such as band brakes or clutches. By utilizing the PHP, one can eliminate the various hydraulic components (oil pump, regulating valve and control valve) in current ATs and achieve a simpler configuration with more efficient operation. With the derived governing equation of motion of the PHP-based actuation system integrated with the friction element (band brake), a switching control law is synthesized based on the sliding-mode theory. To evaluate the effectiveness of the proposed control law, its force tracking performance for the engagement of a friction element during an AT 1\\to 2 up-shift is examined experimentally. It is shown that one can successfully track the desired force trajectory for AT shift control with small tracking error. This study demonstrates the potential of the PHP as a new controllable actuation system for AT friction elements.

Generalization and refinement of an automatic landing system capable of curved trajectories

NASA Technical Reports Server (NTRS)

Sherman, W. L.

1976-01-01

Refinements in the lateral and longitudinal guidance for an automatic landing system capable of curved trajectories were studied. Wing flaps or drag flaps (speed brakes) were found to provide faster and more precise speed control than autothrottles. In the case of the lateral control it is shown that the use of the integral of the roll error in the roll command over the first 30 to 40 seconds of flight reduces the sensitivity of the lateral guidance to the gain on the azimuth guidance angle error in the roll command. Also, changes to the guidance algorithm are given that permit pi-radian approaches and constrain the airplane to fly in a specified plane defined by the position of the airplane at the start of letdown and the flare point.

Terminal area automatic navigation, guidance, and control 1: Automatic rollout, turnoff, and taxis

NASA Technical Reports Server (NTRS)

Pines, S.

1981-01-01

A study developed for the TCV B-737, designed to apply existing navigation aids plus magnetic leader cable signals and develop breaking and reverse thrust guidance laws to provide for rapid automated rollout, turnoff, and taxi to reduce runway occupation time for a wide variety of landing conditions for conventional commercial-type aircraft, is described. Closed loop guidance laws for braking and reverse thrust are derived for rollout, turnoff, and taxi, as functions of the landing speed, the desired taxi speed and the distance to go. Brake limitations for wet runway conditions and reverse thrust limitations are taken into account to provide decision rules to avoid tire skid and to choose an alternate turnoff point, farther down the runway, to accommodate extreme landing conditions.

Dynamic analysis of elastic rubber tired car wheel breaking under variable normal load

NASA Astrophysics Data System (ADS)

Fedotov, A. I.; Zedgenizov, V. G.; Ovchinnikova, N. I.

2017-10-01

The purpose of the paper is to analyze the dynamics of the braking of the wheel under normal load variations. The paper uses a mathematical simulation method according to which the calculation model of an object as a mechanical system is associated with a dynamically equivalent schematic structure of the automatic control. Transfer function tool analyzing structural and technical characteristics of an object as well as force disturbances were used. It was proved that the analysis of dynamic characteristics of the wheel subjected to external force disturbances has to take into account amplitude and phase-frequency characteristics. Normal load variations impact car wheel braking subjected to disturbances. The closer slip to the critical point is, the higher the impact is. In the super-critical area, load variations cause fast wheel blocking.

Mountain Plains Learning Experience Guide: Automotive Repair. Course: Brake Systems.

ERIC Educational Resources Information Center

Schramm, C.; Osland, Walt

One of twelve individualized courses included in an automotive repair curriculum, this course covers theory, operation, and repair of drum brakes, disc brakes, and brake system components. The course is comprised of six units: (1) Fundamentals of Brake Systems, (2) Master Cylinder, (3) Drum Brakes, (4) Disc Brakes, (5) Power Brakes, and (6)…

77 FR 22379 - Petition for Exemption; Summary of Petition Received

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-13

... seeks relief to allow pilots to substitute crosswind component and braking action restrictions, along with a requirement to utilize automatic landing and approach coupler equipment, at the destination and...

49 CFR 570.58 - Electric brake system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... missing. Terminal connections shall be clean. Conductor wire gauge shall not be below the brake... 49 Transportation 6 2013-10-01 2013-10-01 false Electric brake system. 570.58 Section 570.58... 10,000 Pounds § 570.58 Electric brake system. (a) Electric brake system integrity. The average brake...

Excitation Method of Linear-Motor-Type Rail Brake without Using Power Sources by Dynamic Braking with Zero Electrical Output

NASA Astrophysics Data System (ADS)

Sakamoto, Yasuaki; Kashiwagi, Takayuki; Hasegawa, Hitoshi; Sasakawa, Takashi; Fujii, Nobuo

The eddy current rail brake is a type of braking system used in railway vehicles. Because of problems such as rail heating and problems associated with ensuring that power is supplied when the feeder malfunctions, this braking system has not been used for practical applications in Japan. Therefore, we proposed the use of linear induction motor (LIM) technology in eddy current rail brake systems. The LIM rail brake driven by dynamic braking can reduce rail heating and generate the energy required for self-excitation. In this paper, we present an excitation system and control method for the LIM rail brake driven by “dynamic braking with zero electrical output”. The proposed system is based on the concept that the LIM rail brake can be energized without using excitation power sources such as a feeder circuit and that high reliability can be realized by providing an independent excitation system. We have studied this system and conducted verification tests using a prototype LIM rail brake on a roller rig. The results show that the system performance is adequate for commercializing the proposed system, in which the LIM rail brake is driven without using any excitation power source.

Automotive Brake Systems.

ERIC Educational Resources Information Center

Marine Corps Inst., Washington, DC.

This correspondence course, orginally developed for the Marine Corps, is designed to provide mechanics with an understanding of the basic operations of automotive brake systems on military vehicles. The course contains four study units covering hydraulic brakes, air brakes, power brakes, and auxiliary brake systems. A troubleshooting guide for…

Transient switching control strategy from regenerative braking to anti-lock braking with a semi-brake-by-wire system

NASA Astrophysics Data System (ADS)

Li, Liang; Li, Xujian; Wang, Xiangyu; Liu, Yahui; Song, Jian; Ran, Xu

2016-02-01

Regenerative braking is an important technology in improving fuel economy of an electric vehicle (EV). However, additional motor braking will change the dynamic characteristics of the vehicle, leading to braking instability, especially when the anti-lock braking system (ABS) is triggered. In this paper, a novel semi-brake-by-wire system, without the use of a pedal simulator and fail-safe device, is proposed. In order to compensate for the hysteretic characteristics of the designed brake system while ensure braking reliability and fuel economy when the ABS is triggered, a novel switching compensation control strategy using sliding mode control is brought forward. The proposed strategy converts the complex coupling braking process into independent control of hydraulic braking and regenerative braking, through which a balance between braking performance, braking reliability, braking safety and fuel economy is achieved. Simulation results show that the proposed strategy is effective and adaptable in different road conditions while the large wheel slip rate is triggered during a regenerative braking course. The research provides a new possibility of low-cost equipment and better control performance for the regenerative braking in the EV and the hybrid EV.

49 CFR 570.57 - Air brake system and air-over-hydraulic brake subsystem.

Code of Federal Regulations, 2014 CFR

2014-10-01

... pressure drop in psi per minute with brakes released and with brakes fully applied. (d) Air-over-hydraulic... 49 Transportation 6 2014-10-01 2014-10-01 false Air brake system and air-over-hydraulic brake... STANDARDS Vehicles With GVWR of More Than 10,000 Pounds § 570.57 Air brake system and air-over-hydraulic...

49 CFR 570.57 - Air brake system and air-over-hydraulic brake subsystem.

Code of Federal Regulations, 2010 CFR

2010-10-01

... pressure drop in psi per minute with brakes released and with brakes fully applied. (d) Air-over-hydraulic... 49 Transportation 6 2010-10-01 2010-10-01 false Air brake system and air-over-hydraulic brake... STANDARDS Vehicles With GVWR of More Than 10,000 Pounds § 570.57 Air brake system and air-over-hydraulic...

49 CFR 570.57 - Air brake system and air-over-hydraulic brake subsystem.

Code of Federal Regulations, 2012 CFR

2012-10-01

... pressure drop in psi per minute with brakes released and with brakes fully applied. (d) Air-over-hydraulic... 49 Transportation 6 2012-10-01 2012-10-01 false Air brake system and air-over-hydraulic brake... STANDARDS Vehicles With GVWR of More Than 10,000 Pounds § 570.57 Air brake system and air-over-hydraulic...

49 CFR 570.57 - Air brake system and air-over-hydraulic brake subsystem.

Code of Federal Regulations, 2013 CFR

2013-10-01

... pressure drop in psi per minute with brakes released and with brakes fully applied. (d) Air-over-hydraulic... 49 Transportation 6 2013-10-01 2013-10-01 false Air brake system and air-over-hydraulic brake... STANDARDS Vehicles With GVWR of More Than 10,000 Pounds § 570.57 Air brake system and air-over-hydraulic...

Thermal analysis and temperature characteristics of a braking resistor for high-speed trains for changes in the braking current

NASA Astrophysics Data System (ADS)

Lee, Dae-Dong; Kang, Hyun-Il; Shim, Jae-Myung

2015-09-01

Electric brake systems are used in high-speed trains to brake trains by converting the kinetic energy of a railway vehicle to electric energy. The electric brake system consists of a regenerative braking system and a dynamic braking system. When the electric energy generated during the dynamic braking process is changed to heat through the braking resistor, the braking resistor can overheat; thus, failures can occur to the motor block. In this paper, a braking resistor for a high-speed train was used to perform thermal analyses and tests, and the results were analyzed. The analyzed data were used to estimate the dependence of the brake currents and the temperature rises on speed changes up to 300 km/h, at which a test could not be performed.

A motion-constraint logic for moving-base simulators based on variable filter parameters

NASA Technical Reports Server (NTRS)

Miller, G. K., Jr.

1974-01-01

A motion-constraint logic for moving-base simulators has been developed that is a modification to the linear second-order filters generally employed in conventional constraints. In the modified constraint logic, the filter parameters are not constant but vary with the instantaneous motion-base position to increase the constraint as the system approaches the positional limits. With the modified constraint logic, accelerations larger than originally expected are limited while conventional linear filters would result in automatic shutdown of the motion base. In addition, the modified washout logic has frequency-response characteristics that are an improvement over conventional linear filters with braking for low-frequency pilot inputs. During simulated landing approaches of an externally blown flap short take-off and landing (STOL) transport using decoupled longitudinal controls, the pilots were unable to detect much difference between the modified constraint logic and the logic based on linear filters with braking.

49 CFR 570.54 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... from the driver control to a hydraulic brake system to actuate the service brakes. Electric brake system means a system that uses electric current to actuate the service brake. Vacuum brake system means a system that uses a vacuum and atmospheric pressure for transmitting a force from the driver...

49 CFR 570.54 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... from the driver control to a hydraulic brake system to actuate the service brakes. Electric brake system means a system that uses electric current to actuate the service brake. Vacuum brake system means a system that uses a vacuum and atmospheric pressure for transmitting a force from the driver...

Further development of Motorcycle Autonomous Emergency Braking (MAEB), what can in-depth studies tell us? A multinational study.

PubMed

Savino, Giovanni; Rizzi, Matteo; Brown, Julie; Piantini, Simone; Meredith, Lauren; Albanese, Bianca; Pierini, Marco; Fitzharris, Michael

2014-01-01

In 2006, Motorcycle Autonomous Emergency Braking (MAEB) was developed by a European Consortium (Powered Two Wheeler Integrated Safety, PISa) as a crash severity countermeasure for riders. This system can detect an obstacle through sensors in the front of the motorcycle and brakes automatically to achieve a 0.3 g deceleration if the collision is inevitable and the rider does not react. However, if the rider does brake, full braking force is applied automatically. Previous research into the potential benefits of MAEB has shown encouraging results. However, this was based on MAEB triggering algorithms designed for motorcycle crashes involving impacts with fixed objects and rear-end crashes. To estimate the full potential benefit of MAEB, there is a need to understand the full spectrum of motorcycle crashes and further develop triggering algorithms that apply to a wider spectrum of crash scenarios. In-depth crash data from 3 different countries were used: 80 hospital admittance cases collected during 2012-2013 within a 3-h driving range of Sydney, Australia, 40 crashes with Injury Severity Score (ISS)>15 collected in the metropolitan area of Florence, Italy, during 2009-2012, and 92 fatal crashes that occurred in Sweden during 2008-2009. In the first step, the potential applicability of MAEB among the crashes was assessed using a decision tree method. To achieve this, a new triggering algorithm for MAEB was developed to address crossing scenarios as well as crashes involving stationary objects. In the second step, the potential benefit of MAEB across the applicable crashes was examined by using numerical computer simulations. Each crash was reconstructed twice-once with and once without MAEB deployed. The principal finding is that using the new triggering algorithm, MAEB is seen to apply to a broad range of multivehicle motorcycle crashes. Crash mitigation was achieved through reductions in impact speed of up to approximately 10 percent, depending on the crash scenario and the initial vehicle pre-impact speeds. This research is the first attempt to evaluate MAEB with simulations on a broad range of crash scenarios using in-depth data. The results give further insights into the feasibility of MAEB in different speed ranges. It is clear then that MAEB is a promising technology that warrants further attention by researchers, manufacturers, and regulators.

49 CFR 238.431 - Brake system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Brake system. 238.431 Section 238.431... Equipment § 238.431 Brake system. (a) A passenger train's brake system shall be capable of stopping the... train is operating under worst-case adhesion conditions. (b) The brake system shall be designed to allow...

49 CFR 393.41 - Parking brake system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... NECESSARY FOR SAFE OPERATION Brakes § 393.41 Parking brake system. (a) Hydraulic-braked vehicles... road (free of ice and snow). Hydraulic-braked vehicles which were not subject to the parking brake... spring action. If other energy is used to apply the parking brake, there must be an accumulation of that...

49 CFR 393.41 - Parking brake system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... NECESSARY FOR SAFE OPERATION Brakes § 393.41 Parking brake system. (a) Hydraulic-braked vehicles... road (free of ice and snow). Hydraulic-braked vehicles which were not subject to the parking brake... spring action. If other energy is used to apply the parking brake, there must be an accumulation of that...

49 CFR 393.41 - Parking brake system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... NECESSARY FOR SAFE OPERATION Brakes § 393.41 Parking brake system. (a) Hydraulic-braked vehicles... road (free of ice and snow). Hydraulic-braked vehicles which were not subject to the parking brake... spring action. If other energy is used to apply the parking brake, there must be an accumulation of that...

49 CFR 570.56 - Vacuum brake assist unit and vacuum brake system.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... The following requirements apply to vehicles with vacuum brake assist units and vacuum brake systems. (a) Vacuum brake assist unit integrity. The vacuum brake assist unit shall demonstrate integrity as... maintained on the pedal. (1) Inspection procedure. Stop the engine and apply service brake several times to...

Combined hydraulic and regenerative braking system

DOEpatents

Venkataperumal, R.R.; Mericle, G.E.

1979-08-09

A combined hydraulic and regenerative braking system and method for an electric vehicle is disclosed. The braking system is responsive to the applied hydraulic pressure in a brake line to control the braking of the vehicle to be completely hydraulic up to a first level of brake line pressure, to be partially hydraulic at a constant braking force and partially regenerative at a linearly increasing braking force from the first level of applied brake line pressure to a higher second level of brake line pressure, to be partially hydraulic at a linearly increasing braking force and partially regenerative at a linearly decreasing braking force from the second level of applied line pressure to a third and higher level of applied line pressure, and to be completely hydraulic at a linearly increasing braking force from the third level to all higher applied levels of line pressure.

Combined hydraulic and regenerative braking system

DOEpatents

Venkataperumal, Rama R.; Mericle, Gerald E.

1981-06-02

A combined hydraulic and regenerative braking system and method for an electric vehicle, with the braking system being responsive to the applied hydraulic pressure in a brake line to control the braking of the vehicle to be completely hydraulic up to a first level of brake line pressure, to be partially hydraulic at a constant braking force and partially regenerative at a linearly increasing braking force from the first level of applied brake line pressure to a higher second level of brake line pressure, to be partially hydraulic at a linearly increasing braking force and partially regenerative at a linearly decreasing braking force from the second level of applied line pressure to a third and higher level of applied line pressure, and to be completely hydraulic at a linearly increasing braking force from the third level to all higher applied levels of line pressure.

49 CFR 393.41 - Parking brake system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... system shall, at all times, be capable of being applied by either the driver's muscular effort or by... 49 Transportation 5 2010-10-01 2010-10-01 false Parking brake system. 393.41 Section 393.41... NECESSARY FOR SAFE OPERATION Brakes § 393.41 Parking brake system. (a) Hydraulic-braked vehicles...

49 CFR 393.41 - Parking brake system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... system shall, at all times, be capable of being applied by either the driver's muscular effort or by... 49 Transportation 5 2011-10-01 2011-10-01 false Parking brake system. 393.41 Section 393.41... NECESSARY FOR SAFE OPERATION Brakes § 393.41 Parking brake system. (a) Hydraulic-braked vehicles...

75 FR 15620 - Federal Motor Vehicle Safety Standards; Air Brake Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-30

... fully develop improved brake systems and also to ensure vehicle control and stability while braking... [Docket No. NHTSA 2009-0175] RIN 2127-AK62 Federal Motor Vehicle Safety Standards; Air Brake Systems... Federal motor vehicle safety standard for air brake systems by requiring substantial improvements in...

49 CFR 393.40 - Required brake systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... subpart. (2) Air brake systems. Buses, trucks and truck-tractors equipped with air brake systems and..., and 393.52 of this subpart. (4) Electric brake systems. Motor vehicles equipped with electric brake..., trucks and truck tractors manufactured on or after March 1, 1975, and trailers manufactured on or after...

49 CFR 571.116 - Standard No. 116; Motor vehicle brake fluids.

Code of Federal Regulations, 2012 CFR

2012-10-01

... cavity or sac on the surface of a brake cup. Brake fluid means a liquid designed for use in a motor... designed for use in motor vehicle hydraulic brake systems in which the fluid is not in contact with... rubber components of brake systems designed for use with DOT brake fluids. (3) KEEP HYDRAULIC SYSTEM...

49 CFR 571.116 - Standard No. 116; Motor vehicle brake fluids.

Code of Federal Regulations, 2013 CFR

2013-10-01

... cavity or sac on the surface of a brake cup. Brake fluid means a liquid designed for use in a motor... designed for use in motor vehicle hydraulic brake systems in which the fluid is not in contact with... rubber components of brake systems designed for use with DOT brake fluids. (3) KEEP HYDRAULIC SYSTEM...

49 CFR 571.116 - Standard No. 116; Motor vehicle brake fluids.

Code of Federal Regulations, 2014 CFR

2014-10-01

... cavity or sac on the surface of a brake cup. Brake fluid means a liquid designed for use in a motor... designed for use in motor vehicle hydraulic brake systems in which the fluid is not in contact with... rubber components of brake systems designed for use with DOT brake fluids. (3) KEEP HYDRAULIC SYSTEM...

Rail Brake System Using a Linear Induction Motor for Dynamic Braking

NASA Astrophysics Data System (ADS)

Sakamoto, Yasuaki; Kashiwagi, Takayuki; Tanaka, Minoru; Hasegawa, Hitoshi; Sasakawa, Takashi; Fujii, Nobuo

One type of braking system for railway vehicles is the eddy current brake. Because this type of brake has the problem of rail heating, it has not been used for practical applications in Japan. Therefore, we proposed the use of a linear induction motor (LIM) for dynamic braking in eddy current brake systems. The LIM reduces rail heating and uses an inverter for self excitation. In this paper, we estimated the performance of an LIM from experimental results of a fundamental test machine and confirmed that the LIM generates an approximately constant braking force under constant current excitation. At relatively low frequencies, this braking force remains unaffected by frequency changes. The reduction ratio of rail heating is also approximately proportional to the frequency. We also confirmed that dynamic braking resulting in no electrical output can be used for drive control of the LIM. These characteristics are convenient for the realization of the LIM rail brake system.

Optimal design for slip deceleration control in anti-lock braking system

NASA Astrophysics Data System (ADS)

Mishra, Sheelam; Kumar, Pankaj; Rahman, Mohd. Saifur

2018-05-01

ABS (Anti-lock Braking System) is the most advanced braking system implemented in modern cars to avoid the slipping or skidding of the vehicle on the road. Moreover, it reduces the stopping distance of the vehicle because it avoids the locking of the wheel during braking. It enables the driver to steer the vehicle during braking. But every system has its downsides and likewise ABS too, it is not efficient during normal braking or snowy conditions. Our aim is to overcome these downsides and optimize Anti-lock Braking System to make it even better.

49 CFR 570.55 - Hydraulic brake system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... under a 125-pound force applied to the brake pedal and by no illumination of the brake system failure indicator lamp. The brake system shall withstand the application of force to the pedal without failure of... with power brake systems and the ignition turned to “on” in other vehicles, apply a force of 125 pounds...

49 CFR 570.55 - Hydraulic brake system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... under a 125-pound force applied to the brake pedal and by no illumination of the brake system failure indicator lamp. The brake system shall withstand the application of force to the pedal without failure of... with power brake systems and the ignition turned to “on” in other vehicles, apply a force of 125 pounds...

49 CFR 570.55 - Hydraulic brake system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... under a 125-pound force applied to the brake pedal and by no illumination of the brake system failure indicator lamp. The brake system shall withstand the application of force to the pedal without failure of... with power brake systems and the ignition turned to “on” in other vehicles, apply a force of 125 pounds...

49 CFR 570.55 - Hydraulic brake system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... under a 125-pound force applied to the brake pedal and by no illumination of the brake system failure indicator lamp. The brake system shall withstand the application of force to the pedal without failure of... with power brake systems and the ignition turned to “on” in other vehicles, apply a force of 125 pounds...

49 CFR 570.55 - Hydraulic brake system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... under a 125-pound force applied to the brake pedal and by no illumination of the brake system failure indicator lamp. The brake system shall withstand the application of force to the pedal without failure of... with power brake systems and the ignition turned to “on” in other vehicles, apply a force of 125 pounds...

Brake blending strategy for a hybrid vehicle

DOEpatents

Boberg, Evan S.

2000-12-05

A hybrid electric powertrain system is provided including a transmission for driving a pair of wheels of a vehicle and a heat engine and an electric motor/generator coupled to the transmission. A friction brake system is provided for applying a braking torque to said vehicle. A controller unit generates control signals to the electric motor/generator and the friction brake system for controllably braking the vehicle in response to a drivers brake command. The controller unit determines and amount of regenerative torque available and compares this value to a determined amount of brake torque requested for determining the control signals to the electric motor/generator and the friction brake system.

Design and Analysis of a Novel Centrifugal Braking Device for a Mechanical Antilock Braking System.

PubMed

Yang, Cheng-Ping; Yang, Ming-Shien; Liu, Tyng

2015-06-01

A new concept for a mechanical antilock braking system (ABS) with a centrifugal braking device (CBD), termed a centrifugal ABS (C-ABS), is presented and developed in this paper. This new CBD functions as a brake in which the output braking torque adjusts itself depending on the speed of the output rotation. First, the structure and mechanical models of the entire braking system are introduced and established. Second, a numerical computer program for simulating the operation of the system is developed. The characteristics of the system can be easily identified and can be designed with better performance by using this program to studying the effects of different design parameters. Finally, the difference in the braking performance between the C-ABS and the braking system with or without a traditional ABS is discussed. The simulation results indicate that the C-ABS can prevent the wheel from locking even if excessive operating force is provided while still maintaining acceptable braking performance.

Evaluation of odometry algorithm performances using a railway vehicle dynamic model

NASA Astrophysics Data System (ADS)

Allotta, B.; Pugi, L.; Ridolfi, A.; Malvezzi, M.; Vettori, G.; Rindi, A.

2012-05-01

In modern railway Automatic Train Protection and Automatic Train Control systems, odometry is a safety relevant on-board subsystem which estimates the instantaneous speed and the travelled distance of the train; a high reliability of the odometry estimate is fundamental, since an error on the train position may lead to a potentially dangerous overestimation of the distance available for braking. To improve the odometry estimate accuracy, data fusion of different inputs coming from a redundant sensor layout may be used. Simplified two-dimensional models of railway vehicles have been usually used for Hardware in the Loop test rig testing of conventional odometry algorithms and of on-board safety relevant subsystems (like the Wheel Slide Protection braking system) in which the train speed is estimated from the measures of the wheel angular speed. Two-dimensional models are not suitable to develop solutions like the inertial type localisation algorithms (using 3D accelerometers and 3D gyroscopes) and the introduction of Global Positioning System (or similar) or the magnetometer. In order to test these algorithms correctly and increase odometry performances, a three-dimensional multibody model of a railway vehicle has been developed, using Matlab-Simulink™, including an efficient contact model which can simulate degraded adhesion conditions (the development and prototyping of odometry algorithms involve the simulation of realistic environmental conditions). In this paper, the authors show how a 3D railway vehicle model, able to simulate the complex interactions arising between different on-board subsystems, can be useful to evaluate the odometry algorithm and safety relevant to on-board subsystem performances.

14 CFR 25.735 - Brakes and braking systems.

Code of Federal Regulations, 2014 CFR

2014-01-01

... speed. The most severe landing stop brake kinetic energy absorption requirement of each wheel, brake... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Brakes and braking systems. 25.735 Section 25.735 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...

14 CFR 25.735 - Brakes and braking systems.

Code of Federal Regulations, 2012 CFR

2012-01-01

... speed. The most severe landing stop brake kinetic energy absorption requirement of each wheel, brake... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Brakes and braking systems. 25.735 Section 25.735 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...

14 CFR 25.735 - Brakes and braking systems.

Code of Federal Regulations, 2013 CFR

2013-01-01

... speed. The most severe landing stop brake kinetic energy absorption requirement of each wheel, brake... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Brakes and braking systems. 25.735 Section 25.735 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...

Guidance and control requirements for high-speed Rollout and Turnoff (ROTO)

NASA Technical Reports Server (NTRS)

Goldthorpe, Steve H.; Kernik, Alan C.; Mcbee, Larry S.; Preston, Orv W.

1995-01-01

This report defines the initial requirements for designing a research high-speed rollout and turnoff (ROTO) guidance and control system applicable to transport class aircraft whose purpose is to reduce the average runway occupancy time (ROT) for aircraft operations. The requirements will be used to develop a ROTO system for both automatic and manual piloted operation under normal and reduced visibility conditions. Requirements were determined for nose wheel/rudder steering, braking/reverse thrust, and the navigation system with the aid of a non-real time, three degree-of-freedom MD-11 simulation program incorporating airframe and gear dynamics. The requirements were developed for speeds up to 70 knots using 30 ft exit geometries under dry and wet surface conditions. The requirements were generated under the assumptions that the aircraft landing system meets the current Category III touchdown dispersion requirements and that aircraft interarrival spacing is 2 nautical miles. This effort determined that auto-asymmetric braking is needed to assist steering for aft center-of-gravity aircraft. This report shows various time-history plots of the aircraft performance for the ROTO operation. This effort also investigated the state-of-the-art in the measurement of the runway coefficient of friction for various runway conditions.

Effects of uncertainty, transmission type, driver age and gender on brake reaction and movement time.

PubMed

Warshawsky-Livne, Lora; Shinar, David

2002-01-01

Braking time (BT) is a critical component in safe driving, and various approaches have been applied to minimize it. This study analyzed the components of BT in order to assess the effects of age, gender, vehicle transmission type, and event uncertainty, on its two primary components, perception-reaction time and brake-movement time. Perception-reaction time and brake-movement time were measured at the onset of lights for 72 subjects in a simulator. The six experimental conditions were three levels of uncertainty conditions (none, some, and some + false alarms) and two types of transmission (manual and automatic). The 72 subjects, half male and half female, were further divided into three age groups (mean of 23, 30, and 62 years). Each subject had 10 trials in each of the three levels of uncertainty conditions. Transmission type did not significantly affect either perception-reaction time or brake-movement time. Perception-reaction time increased significantly from 0.32 to 0.42 s (P < .05) as uncertainty increased but brake-movement time did not change. Perception-reaction time increased (from 0.35 to 0.43 s) with age but brake-movement time did not change with age. Gender did not affect perception-reaction time but did affect brake-movement time (males 0.19 s vs. females 0.16 s). At 90 km/h, a car travels 0.25 m in 0.01 s. Consequently, even such small effects multiplied by millions of vehicle-kilometers can contribute to significant savings in lives and damages.

Architecture and Integration Requirements for an ULCE (Unified Life Cycle Engineering) Design Environment.

DTIC Science & Technology

1988-04-01

Locate brake lines on rear side of the gear structure to prevent damage. * Provide emergency brake system , independent of the normal system , and capable of...stopping the aircraft in the same distance as the normal system . -.. * Consider brake temperature in calculating brake energy capability. * Install a...and takeoff. In addition, assume a brake nearing the end of its recommended life. - Antiskid systems shall be as reliable as the rest of the braking

Backup Mechanical Brake System of the Wind Turbine

NASA Astrophysics Data System (ADS)

Sirotkin, E. A.; Solomin, E. V.; Gandzha, S. A.; Kirpichnikova, I. M.

2018-01-01

Paper clarifies the necessity of the emergency mechanical brake systems usage for wind turbines. We made a deep analysis of the wind turbine braking methods available on the market, identifying their strengths and weaknesses. The electromechanical braking appeared the most technically reasonable and economically attractive. We described the developed combined electromechanical brake system for vertical axis wind turbine driven from electric drive with variable torque enough to brake over the turbine even on the storm wind speed up to 45 m/s. The progress was made due to the development of specific kinematic brake system diagram and intelligent control system managed by special operation algorithm.

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces: Hydromechanically controlled system

NASA Technical Reports Server (NTRS)

Tanner, J. A.; Stubbs, S. M.; Smith, E. G.

1981-01-01

The investigation utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC-9 series 10 airplane. The landing-gear strut was replaced by a dynamometer. During maximum braking, average braking behavior indexes based upon brake pressure, brake torque, and drag-force friction coefficient developed by the antiskid system were generally higher on dry surfaces than on wet surfaces. The three braking behavior indexes gave similar results but should not be used interchangeably as a measure of the braking of this antiskid sytem. During the transition from a dry to a flooded surface under heavy braking, the wheel entered into a deep skid but the antiskid system reacted quickly by reducing brake pressure and performed normally during the remainder of the run on the flooded surface. The brake-pressure recovery following transition from a flooded to a dry surface was shown to be a function of the antiskid modulating orifice.

Brakes. Auto Mechanics Curriculum Guide. Module 6. Instructor's Guide.

ERIC Educational Resources Information Center

Allain, Robert

This module is the sixth of nine modules in the competency-based Missouri Auto Mechanics Curriculum Guide. Eight units cover: introduction to automotive brake systems; disc and drum brake system components and how they operate; properties of brake fluid and procedures for bleeding the brake system; diagnosing and determining needed repairs on…

A battery-run pulsed motor with inherent dynamic electronic switch control

NASA Astrophysics Data System (ADS)

Tripathi, K. C.; Lal, P.; Sarma, P. R.; Sharma, A. K.; Prakash, V.

1980-02-01

A new type of battery-run brushless ferrite-magnet dc motor system is described. Its rotor part consists of a few permanent ceramic (ferrite) magnets uniformly spread on the rim of a disk (wheel) and the stator part consists of electromagnets placed in such a way that when energized, they always form a repulsive couple to rotate the disk. A sensor coil is placed to give an induced pulse signal, which acts as an inherent dynamic switching time control for the automatic electronic control system. Control of speed, brake system, and safety measures are also discussed. Experimental values for the present system are given. Some possible applications are suggested.

Fuzzy logic electric vehicle regenerative antiskid braking and traction control system

DOEpatents

Cikanek, S.R.

1994-10-25

An regenerative antiskid braking and traction control system using fuzzy logic for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensor and determining if regenerative antiskid braking control, requiring hydraulic braking control, and requiring traction control are required. The processor then employs fuzzy logic based on the determined vehicle state and provides command signals to a motor controller to control operation of the electric traction motor and to the brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative braking control, hydraulic braking control, and traction control. 123 figs.

Electric vehicle regenerative antiskid braking and traction control system

DOEpatents

Cikanek, S.R.

1995-09-12

An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydraulic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control. 10 figs.

Electric vehicle regenerative antiskid braking and traction control system

DOEpatents

Cikanek, Susan R.

1995-01-01

An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydrualic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control.

Fuzzy logic electric vehicle regenerative antiskid braking and traction control system

DOEpatents

Cikanek, Susan R.

1994-01-01

An regenerative antiskid braking and traction control system using fuzzy logic for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensor and determining if regenerative antiskid braking control, requiring hydraulic braking control, and requiring traction control are required. The processor then employs fuzzy logic based on the determined vehicle state and provides command signals to a motor controller to control operation of the electric traction motor and to the brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative braking control, hydraulic braking control, and traction control.

An antilock molecular braking system.

PubMed

Sun, Wei-Ting; Huang, Shou-Ling; Yao, Hsuan-Hsiao; Chen, I-Chia; Lin, Ying-Chih; Yang, Jye-Shane

2012-08-17

A light-driven molecular brake displaying an antilock function is constructed by introducing a nonradiative photoinduced electron transfer (PET) decay channel to compete with the trans (brake-off) → cis (brake-on) photoisomerization. A fast release of the brake can be achieved by deactivating the PET process through addition of protons. The cycle of irradiation-protonation-irradiation-deprotonation conducts the brake function and mimics the antilock braking system (ABS) of vehicles.

Study on antilock brake system with elastic membrane vibration generated by controlled solenoid excitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wibowo,, E-mail: wibowo-uns@yahoo.com; Zakaria,, E-mail: zakaaria27@gmail.com; Lambang, Lullus, E-mail: lulus-l@yahoo.com

The most effective chassis control system for improving vehicle safety during severe braking is anti-lock braking system (ABS). Antilock effect can be gained by vibrate the pad brake at 7 to 20 cycle per second. The aim of this study is to design a new method of antilock braking system with membrane elastic vibrated by solenoid. The influence of the pressure fluctuations of brake fluid is investigated. Vibration data is collected using a small portable accelerometer-slam stick. The experiment results that the vibration of brake pad caused by controlled solenoid excitation at 10 Hz is obtained by our new method. Themore » result of measurements can be altered by varying brake fluid pressure.« less

Study on antilock brake system with elastic membrane vibration generated by controlled solenoid excitation

NASA Astrophysics Data System (ADS)

Wibowo, Zakaria, Lambang, Lullus; Triyono, Muhayat, Nurul

2016-03-01

The most effective chassis control system for improving vehicle safety during severe braking is anti-lock braking system (ABS). Antilock effect can be gained by vibrate the pad brake at 7 to 20 cycle per second. The aim of this study is to design a new method of antilock braking system with membrane elastic vibrated by solenoid. The influence of the pressure fluctuations of brake fluid is investigated. Vibration data is collected using a small portable accelerometer-slam stick. The experiment results that the vibration of brake pad caused by controlled solenoid excitation at 10 Hz is obtained by our new method. The result of measurements can be altered by varying brake fluid pressure.

Design and analysis of an MR rotary brake for self-regulating braking torques.

PubMed

Yun, Dongwon; Koo, Jeong-Hoi

2017-05-01

This paper presents a novel Magneto-rheological (MR) brake system that can self-regulate the output braking torques. The proposed MR brake can generate a braking torque at a critical rotation speed without an external power source, sensors, or controllers, making it a simple and cost-effective device. The brake system consists of a rotary disk, permanent magnets, springs, and MR fluid. The permanent magnets are attached to the rotary disk via the springs, and they move outward through grooves with two different gap distances along the radial direction of the stator due to the centrifugal force. Thus, the position of the magnets is dependent on the spin speed, and it can determine the magnetic fields applied to MR fluids. Proper design of the stator geometry gives the system unique torque characteristics. To show the performance of an MR brake system, the electromagnetic characteristics of the system are analyzed, and the torques generated by the brake are calculated using the result of the electromagnetic analysis. Using a baseline model, a parametric study is conducted to investigate how the design parameters (geometric shapes and material selection) affect the performance of the brake system. After the simulation study, a prototype brake system is constructed and its performance is experimentally evaluated. The experimental results show that the prototype produced the maximum torque of 1.2 N m at the rotational speed of 100 rpm. The results demonstrate the feasibility of the proposed MR brake as a speed regulator in rotating systems.

Improvement in vehicle agility and stability by G-Vectoring control

NASA Astrophysics Data System (ADS)

Yamakado, Makoto; Takahashi, Jyunya; Saito, Shinjiro; Yokoyama, Atsushi; Abe, Masato

2010-12-01

We extracted a trade-off strategy between longitudinal traction/braking force and cornering force by using jerk information through observing an expert driver's voluntary braking and turning action. Using the expert driver's strategy, we developed a new control concept, called 'G-Vectoring control', which is an automatic longitudinal acceleration control (No DYC) in accordance with the vehicle's lateral jerk caused by the driver's steering manoeuvres. With the control, the direction of synthetic acceleration (G) changes seamlessly (i.e. vectoring). The improvements in vehicle agility and stability were evaluated by theoretical analysis and through computer simulation. We then introduced a 'G-Vectoring' equipped test vehicle realised by brake-by-wire technology and executed a detailed examination on a test track. We have confirmed that the vehicle motion in view of both handling and ride quality has improved dramatically.

Evaluation of Squeal Noise from the WMATA Transit Car Disc Brake System : A Preliminary Investigation

DOT National Transportation Integrated Search

1981-03-01

The Washington Metropolitan Area Transit Authority (WMATA) rail transit car design adopted the use of disc brakes as the primary friction braking system. Unfortunately, while disc brakes are more efficient than the traditional tread brake designs, th...

A Computer-Controlled Laser Bore Scanner

NASA Astrophysics Data System (ADS)

Cheng, Charles C.

1980-08-01

This paper describes the design and engineering of a laser scanning system for production applications. The laser scanning techniques, the timing control, the logic design of the pattern recognition subsystem, the digital computer servo control for the loading and un-loading of parts, and the laser probe rotation and its synchronization will be discussed. The laser inspection machine is designed to automatically inspect the surface of precision-bored holes, such as those in automobile master cylinders, without contacting the machined surface. Although the controls are relatively sophisticated, operation of the laser inspection machine is simple. A laser light beam from a commercially available gas laser, directed through a probe, scans the entire surface of the bore. Reflected light, picked up through optics by photoelectric sensors, generates signals that are fed to a mini-computer for processing. A pattern recognition techniques program in the computer determines acceptance or rejection of the part being inspected. The system's acceptance specifications are adjustable and are set to the user's established tolerances. However, the computer-controlled laser system is capable of defining from 10 to 75 rms surface finish, and voids or flaws from 0.0005 to 0.020 inch. Following the successful demonstration with an engineering prototype, the described laser machine has proved its capability to consistently ensure high-quality master brake cylinders. It thus provides a safety improvement for the automotive braking system. Flawless, smooth cylinder bores eliminate premature wearing of the rubber seals, resulting in a longer-lasting master brake cylinder and a safer and more reliable automobile. The results obtained from use of this system, which has been in operation about a year for replacement of a tedious, manual operation on one of the high-volume lines at the Bendix Hydraulics Division, have been very satisfactory.

NAC Off-Vehicle Brake Testing Project

DTIC Science & Technology

2007-05-01

disc pads/rotors and drum shoe assemblies/ drums - Must use vehicle “OEM” brake /hub-end hardware, or ESA... brake component comparison analysis (primary)* - brake system design analysis - brake system component failure analysis - (*) limited to disc pads...e.g. disc pads/rotors, drum shoe assemblies/ drums . - Not limited to “OEM” brake /hub-end hardware as there is none ! - Weight transfer, plumbing,

Vibration analysis on automatic take-up device of belt conveyor

NASA Astrophysics Data System (ADS)

Qin, Tailong; Wei, Jin

2008-10-01

Through introducing application condition of belt conveyor in the modern mining industry, the paper proposed, in the dynamic course of its starting, braking or loading, it would produce moving tension and elastic wave. And analyzed the factors cause the automatic take-up device of belt conveyor vibrating: the take-up device's structure and the elastic wave. Finally the paper proposed the measure to reduce vibration and carried on the modeling and simulation on the tension buffer device.

Adaptive controller for regenerative and friction braking system

DOEpatents

Davis, R.I.

1990-10-16

A regenerative and friction braking system for a vehicle having one or more road wheels driven by an electric traction motor includes a driver responsive device for producing a brake demand signal having a magnitude corresponding to the level of braking force selected by the driver and friction and regenerative brakes operatively connected with the road wheels of the vehicle. A system according to this invention further includes control means for operating the friction and regenerative braking subsystems so that maximum brake torques sustainable by the road wheels of the vehicle without skidding or slipping will not be exceeded. 8 figs.

Adaptive controller for regenerative and friction braking system

DOEpatents

Davis, Roy I.

1990-01-01

A regenerative and friction braking system for a vehicle having one or more roadwheels driven by an electric traction motor includes a driver responsive device for producing a brake demand signal having a magnitude corresponding to the level of braking force selected by the driver and friction and regenerative brakes operatively connected with the roadwheels of the vehicle. A system according to this invention further includes control means for operating the friction and regenerative braking subsystems so that maximum brake torques sustainable by the roadwheels of the vehicle without skidding or slipping will not be exceeded.

49 CFR 570.54 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

...-hydraulic brake subsystem means a subsystem of the air brake that uses compressed air to transmit a force from the driver control to a hydraulic brake system to actuate the service brakes. Electric brake... a system that uses a vacuum and atmospheric pressure for transmitting a force from the driver...

49 CFR 570.54 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

...-hydraulic brake subsystem means a subsystem of the air brake that uses compressed air to transmit a force from the driver control to a hydraulic brake system to actuate the service brakes. Electric brake... a system that uses a vacuum and atmospheric pressure for transmitting a force from the driver...

49 CFR 570.54 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

...-hydraulic brake subsystem means a subsystem of the air brake that uses compressed air to transmit a force from the driver control to a hydraulic brake system to actuate the service brakes. Electric brake... a system that uses a vacuum and atmospheric pressure for transmitting a force from the driver...

Impact of automatic calibration techniques on HMD life cycle costs and sustainable performance

NASA Astrophysics Data System (ADS)

Speck, Richard P.; Herz, Norman E., Jr.

2000-06-01

Automatic test and calibration has become a valuable feature in many consumer products--ranging from antilock braking systems to auto-tune TVs. This paper discusses HMDs (Helmet Mounted Displays) and how similar techniques can reduce life cycle costs and increase sustainable performance if they are integrated into a program early enough. Optical ATE (Automatic Test Equipment) is already zeroing distortion in the HMDs and thereby making binocular displays a practical reality. A suitcase sized, field portable optical ATE unit could re-zero these errors in the Ready Room to cancel the effects of aging, minor damage and component replacement. Planning on this would yield large savings through relaxed component specifications and reduced logistic costs. Yet, the sustained performance would far exceed that attained with fixed calibration strategies. Major tactical benefits can come from reducing display errors, particularly in information fusion modules and virtual `beyond visual range' operations. Some versions of the ATE described are in production and examples of high resolution optical test data will be discussed.

49 CFR 238.5 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... next midnight on a given date. Class I brake test means a complete passenger train brake system test... ensure that the air brake system is 100 percent effective. Class IA brake test means a test and... response to train line commands. Class II brake test means a test and inspection (as further specified in...

Wheel slip dump valve for railway braking system

NASA Astrophysics Data System (ADS)

Zhang, Xuan; Zhang, LiHao; Li, QingXuan; Shi, YanTao

2017-09-01

As we all know, pneumatic braking system plays an important role in the safety of the whole vehicle. In the anti slip braking system, the pressure of braking cylinder can be adjusted by the quick power response of wheel slip dump valve, so that the lock situation won’t occur during vehicle service. During the braking of railway vehicles, the braking force provided by braking disc reduces vehicle’s speed. But the locking slip will happen due to the oversize of braking force or the reduction of sticking coefficient between wheel and rail. It will cause not only the decline of braking performance but also the increase of braking distance. In the meanwhile, it will scratch the wheel and influence the stable running of vehicles. Now, the speed of passenger vehicle has been increased. In order to shorten the braking distance as far as possible, sticking stickiness must be fully applied. So the occurrence probability of wheel slip is increased.

30 CFR 75.1404-1 - Braking system.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Braking system. 75.1404-1 Section 75.1404-1... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips § 75.1404-1 Braking system. A locomotive equipped with a dual braking system will be deemed to satisfy the requirements of § 75.1404 for a...

30 CFR 75.1404-1 - Braking system.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Braking system. 75.1404-1 Section 75.1404-1... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips § 75.1404-1 Braking system. A locomotive equipped with a dual braking system will be deemed to satisfy the requirements of § 75.1404 for a...

49 CFR 232.503 - Process to introduce new brake system technology.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Process to introduce new brake system technology... Technology § 232.503 Process to introduce new brake system technology. (a) Pursuant to the procedures... brake system technology, prior to implementing the plan. (b) Each railroad shall complete a pre-revenue...

49 CFR 232.503 - Process to introduce new brake system technology.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Process to introduce new brake system technology... Technology § 232.503 Process to introduce new brake system technology. (a) Pursuant to the procedures... brake system technology, prior to implementing the plan. (b) Each railroad shall complete a pre-revenue...

49 CFR 232.503 - Process to introduce new brake system technology.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Process to introduce new brake system technology... Technology § 232.503 Process to introduce new brake system technology. (a) Pursuant to the procedures... brake system technology, prior to implementing the plan. (b) Each railroad shall complete a pre-revenue...

49 CFR 232.503 - Process to introduce new brake system technology.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Process to introduce new brake system technology... Technology § 232.503 Process to introduce new brake system technology. (a) Pursuant to the procedures... brake system technology, prior to implementing the plan. (b) Each railroad shall complete a pre-revenue...

49 CFR 232.503 - Process to introduce new brake system technology.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Process to introduce new brake system technology... Technology § 232.503 Process to introduce new brake system technology. (a) Pursuant to the procedures... brake system technology, prior to implementing the plan. (b) Each railroad shall complete a pre-revenue...

38 CFR 17.157 - Definition-adaptive equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... includes, but is not limited to, a basic automatic transmission, power steering, power brakes, power window lifts, power seats, air-conditioning equipment when necessary for the health and safety of the veteran... MEDICAL Automotive Equipment and Driver Training § 17.157 Definition-adaptive equipment. The term...

Brake Fluid Compatibility Studies with Advanced Brake Systems

DTIC Science & Technology

2016-01-16

and chemical characterization tests. Increased wear seen with the silicone brake fluid on brake system parts was substantiated by laboratory bench...tests and dynamic seal tests, followed by a series of physical and chemical characterization tests on used silicone brake fluid and hydraulic...elastomers with silicone brake fluid was conducted at ambient and 40 °C, primarily to determine using GC-MS, if the chemical constituents in the

NHTSA's heavy duty vehicle brake research program report number 11 : evaluation of stopping performance of trailer antilock brake systems

DOT National Transportation Integrated Search

1997-04-01

In order to better understand the functioning of antilock brake systems on pneumatically braked trailers, a series of tests were conducted to evaluate different ABS control strategies, performance variations among systems supplied by different manufa...

Fallback level concepts for conventional and by-wire automotive brake systems

NASA Astrophysics Data System (ADS)

Retzer, H.; Mishra, R.; Ball, A.; Schmidt, K.

2012-05-01

Brake-by-wire represents the replacement of traditional brake components such as pumps, hoses, fluids, brake boosters, and master cylinders by electronic sensors and actuators. The different design of these brake concepts poses new challenges for the automotive industry with regard to availability and fallback levels in comparison to standard conventional brake systems. This contribution focuses on the development of appropriate fallback level concepts. Hardware-in-the-loop (HIL) techniques and field trials will be used to investigate the performance and the usability of such systems.

Braking system for use with an arbor of a microscope

DOEpatents

Norgren, Duane U.

1984-01-01

A balanced braking system comprising a plurality of braking assemblies located about a member to be braked. Each of the braking assemblies consists of a spring biased piston of a first material fitted into a body of a different material which has a greater contraction upon cooling than the piston material. The piston is provided with a recessed head portion over which is positioned a diaphragm and forming a space therebetween to which is connected a pressurized fluid supply. The diaphragm is controlled by the fluid in the space to contact or withdraw from the member to be braked. A cooling device causes the body within which the piston is fitted to contract more than the piston, producing a tight shrink fit therebetween. The braking system is particularly applicable for selectively braking an arbor of an electron microscope which immobilizes, for example, a vertically adjustable low temperature specimen holder during observation. The system provides balanced braking forces which can be easily removed and re-established with minimal disturbance to arbor location.

Braking system

DOEpatents

Norgren, D.U.

1982-09-23

A balanced braking system comprising a plurality of braking assemblies located about a member to be braked. Each of the braking assemblies consists of a spring biased piston of a first material fitted into a body of a different material which has a greater contraction upon cooling than the piston material. The piston is provided with a recessed head portion over which is positioned a diaphragm and forming a space therebetween to which is connected a pressurized fluid supply. The diaphragm is controlled by the fluid in the space to contact or withdraw from the member to be braked. A cooling means causes the body within which the piston is fitted to contract more than the piston, producing a tight shrink fit therebetween. The braking system is particularly applicable for selectively braking an arbor of an electron microscope which immobilizes, for example, a vertically adjustable low temperature specimen holder during observation. The system provides balanced braking forces which can be easily removed and re-established with minimal disturbance to arbor location.

Automatic Parking of Self-Driving CAR Based on LIDAR

NASA Astrophysics Data System (ADS)

Lee, B.; Wei, Y.; Guo, I. Y.

2017-09-01

To overcome the deficiency of ultrasonic sensor and camera, this paper proposed a method of autonomous parking based on the self-driving car, using HDL-32E LiDAR. First the 3-D point cloud data was preprocessed. Then we calculated the minimum size of parking space according to the dynamic theories of vehicle. Second the rapidly-exploring random tree algorithm (RRT) algorithm was improved in two aspects based on the moving characteristic of autonomous car. And we calculated the parking path on the basis of the vehicle's dynamics and collision constraints. Besides, we used the fuzzy logic controller to control the brake and accelerator in order to realize the stably of speed. At last the experiments were conducted in an autonomous car, and the results show that the proposed automatic parking system is feasible and effective.

49 CFR 232.611 - Periodic maintenance.

Code of Federal Regulations, 2012 CFR

2012-10-01

... wiring and brackets; (2) ECP brake system electrical connections; and (3) Car mounted ECP brake system components. (b) Single car air brake test procedures. Prior to placing a freight car equipped with an ECP... car equipped with an ECP brake system shall be inspected and repaired before being released from a...

49 CFR 232.611 - Periodic maintenance.

Code of Federal Regulations, 2014 CFR

2014-10-01

... wiring and brackets; (2) ECP brake system electrical connections; and (3) Car mounted ECP brake system components. (b) Single car air brake test procedures. Prior to placing a freight car equipped with an ECP... car equipped with an ECP brake system shall be inspected and repaired before being released from a...

49 CFR 232.611 - Periodic maintenance.

Code of Federal Regulations, 2013 CFR

2013-10-01

... wiring and brackets; (2) ECP brake system electrical connections; and (3) Car mounted ECP brake system components. (b) Single car air brake test procedures. Prior to placing a freight car equipped with an ECP... car equipped with an ECP brake system shall be inspected and repaired before being released from a...

49 CFR 232.611 - Periodic maintenance.

Code of Federal Regulations, 2011 CFR

2011-10-01

... wiring and brackets; (2) ECP brake system electrical connections; and (3) Car mounted ECP brake system components. (b) Single car air brake test procedures. Prior to placing a freight car equipped with an ECP... car equipped with an ECP brake system shall be inspected and repaired before being released from a...

49 CFR 232.611 - Periodic maintenance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... wiring and brackets; (2) ECP brake system electrical connections; and (3) Car mounted ECP brake system components. (b) Single car air brake test procedures. Prior to placing a freight car equipped with an ECP... car equipped with an ECP brake system shall be inspected and repaired before being released from a...

49 CFR 214.529 - In-service failure of primary braking system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false In-service failure of primary braking system. 214... Maintenance Machines and Hi-Rail Vehicles § 214.529 In-service failure of primary braking system. (a) In the event of a total in-service failure of its primary braking system, an on-track roadway maintenance...

49 CFR 214.529 - In-service failure of primary braking system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false In-service failure of primary braking system. 214... Maintenance Machines and Hi-Rail Vehicles § 214.529 In-service failure of primary braking system. (a) In the event of a total in-service failure of its primary braking system, an on-track roadway maintenance...

49 CFR 214.529 - In-service failure of primary braking system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Maintenance Machines and Hi-Rail Vehicles § 214.529 In-service failure of primary braking system. (a) In the event of a total in-service failure of its primary braking system, an on-track roadway maintenance... 49 Transportation 4 2010-10-01 2010-10-01 false In-service failure of primary braking system. 214...

CFD Modeling and Simulation of Aeorodynamic Cooling of Automotive Brake Rotor

NASA Astrophysics Data System (ADS)

Belhocien, Ali; Omar, Wan Zaidi Wan

Braking system is one of the important control systems of an automotive. For many years, the disc brakes have been used in automobiles for the safe retarding of the vehicles. During the braking enormous amount of heat will be generated and for effective braking sufficient heat dissipation is essential. The thermal performance of disc brake depends upon the characteristics of the airflow around the brake rotor and hence the aerodynamics is an important in the region of brake components. A CFD analysis is carried out on the braking system as a case study to make out the behavior of airflow distribution around the disc brake components using ANSYS CFX software. We are interested in the determination of the heat transfer coefficient (HTC) on each surface of a ventilated disc rotor varying with time in a transient state using CFD analysis, and then imported the surface film condition data into a corresponding FEM model for disc temperature analysis.

Hierarchical Control Strategy for the Cooperative Braking System of Electric Vehicle.

PubMed

Peng, Jiankun; He, Hongwen; Liu, Wei; Guo, Hongqiang

2015-01-01

This paper provides a hierarchical control strategy for cooperative braking system of an electric vehicle with separated driven axles. Two layers are defined: the top layer is used to optimize the braking stability based on two sliding mode control strategies, namely, the interaxle control mode and signal-axle control strategies; the interaxle control strategy generates the ideal braking force distribution in general braking condition, and the single-axle control strategy can ensure braking safety in emergency braking condition; the bottom layer is used to maximize the regenerative braking energy recovery efficiency with a reallocated braking torque strategy; the reallocated braking torque strategy can recovery braking energy as much as possible in the premise of meeting battery charging power. The simulation results show that the proposed hierarchical control strategy is reasonable and can adapt to different typical road surfaces and load cases; the vehicle braking stability and safety can be guaranteed; furthermore, the regenerative braking energy recovery efficiency can be improved.

Hierarchical Control Strategy for the Cooperative Braking System of Electric Vehicle

PubMed Central

Peng, Jiankun; He, Hongwen; Guo, Hongqiang

2015-01-01

This paper provides a hierarchical control strategy for cooperative braking system of an electric vehicle with separated driven axles. Two layers are defined: the top layer is used to optimize the braking stability based on two sliding mode control strategies, namely, the interaxle control mode and signal-axle control strategies; the interaxle control strategy generates the ideal braking force distribution in general braking condition, and the single-axle control strategy can ensure braking safety in emergency braking condition; the bottom layer is used to maximize the regenerative braking energy recovery efficiency with a reallocated braking torque strategy; the reallocated braking torque strategy can recovery braking energy as much as possible in the premise of meeting battery charging power. The simulation results show that the proposed hierarchical control strategy is reasonable and can adapt to different typical road surfaces and load cases; the vehicle braking stability and safety can be guaranteed; furthermore, the regenerative braking energy recovery efficiency can be improved. PMID:26236772

49 CFR 232.217 - Train brake tests conducted using yard air.

Code of Federal Regulations, 2010 CFR

2010-10-01

... reduction of brake pipe air pressure at the same, or slower, rate as an engineer's brake valve. (b) The yard... potential overcharge conditions to the train brake system are avoided, the yard air test device may be... section, when yard air is used the train air brake system must be charged and tested as prescribed by...

Antiskid braking system

NASA Technical Reports Server (NTRS)

Pazdera, J. S.

1974-01-01

Published report describes analytical development and simulation of braking system. System prevents wheels from skidding when brakes are applied, significantly reducing stopping distance. Report also presents computer simulation study on system as applied to aircraft.

Diagnostics monitor of the braking efficiency in the on board diagnostics system for the motor vehicles

NASA Astrophysics Data System (ADS)

Gajek, Andrzej

2016-09-01

The article presents diagnostics monitor for control of the efficiency of brakes in various road conditions in cars equipped with pressure sensor in brake (ESP) system. Now the brake efficiency of the vehicles is estimated periodically in the stand conditions on the base of brake forces measurement or in the road conditions on the base of the brake deceleration. The presented method allows to complete the stand - periodical tests of the brakes by current on board diagnostics system OBD for brakes. First part of the article presents theoretical dependences between deceleration of the vehicle and brake pressure. The influence of the vehicle mass, initial speed of braking, temperature of brakes, aerodynamic drag, rolling resistance, engine resistance, state of the road surface, angle of the road sloping on the deceleration have been analysed. The manner of the appointed of these parameters has been analysed. The results of the initial investigation have been presented. At the end of the article the strategy of the estimation and signalization of the irregular value of the deceleration are presented.

An automatic method for detecting sliding railway wheels and hot bearings using thermal imagery.

DOT National Transportation Integrated Search

2016-05-03

One of the most important safety-related tasks in the rail industry is early detection of defective rolling : stock components. Railway wheels and wheel bearings are two components prone to damage due to : their interactions with brakes and railway t...

40 CFR 86.128-79 - Transmissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., shall be run according to the manufacturer's recommendations to the ultimate purchaser, Provided, That... recommendations to the ultimate purchaser. (c) Idle modes less than one minute in length shall be run with automatic transmissions in “Drive” and the wheels braked; manual transmissions shall be in gear with the...

The role of looming and attention capture in drivers' braking responses.

PubMed

Terry, Hugh R; Charlton, Samuel G; Perrone, John A

2008-07-01

This study assessed the ability of drivers to detect the deceleration of a preceding vehicle in a simulated vehicle-following task. The size of the preceding vehicles (car, van, or truck) and following speeds (50, 70, or 100 km/h) were systematically varied. Participants selected a preferred following distance by engaging their vehicle's cruise control and when the preceding vehicle began decelerating (no brake lights were illuminated), the participant's braking latency and distances to the lead vehicle were recorded. The experiment also employed a secondary task condition to examine how the attention-capturing properties of a looming vehicle were affected by driver distraction. The results indicated that a looming stimulus is capable of redirecting a driver's attention in a vehicle following task and, as with detection of brake lights, a driver's detection of a looming vehicle is compromised in the presence of a distracting task. Interestingly, increases in vehicle size had the effect of decreasing drivers' braking latencies and drivers engaged in the secondary task were significantly closer to the lead vehicle when they began braking, regardless of the size of the leading vehicle. Performance decrements resulting from the secondary task were reflected in a time-to-collision measure but not in optic expansion rate, lending support to earlier arguments that time-to-collision estimates require explicit cognitive judgements while perception of optic expansion may function in a more automatic fashion to redirect a driver's attention when cognitive resources are low or collision is imminent.

Dynamic multistation photometer

DOEpatents

Bauer, Martin L.; Johnson, Wayne F.; Lakomy, Dale G.

1977-01-01

A portable fast analyzer is provided that uses a magnetic clutch/brake to rapidly accelerate the analyzer rotor, and employs a microprocessor for automatic analyzer operation. The rotor is held stationary while the drive motor is run up to speed. When it is desired to mix the sample(s) and reagent(s), the brake is deenergized and the clutch is energized wherein the rotor is very rapidly accelerated to the running speed. The parallel path rotor that is used allows the samples and reagents to be mixed the moment they are spun out into the rotor cuvetes and data acquisition begins immediately. The analyzer will thus have special utility for fast reactions.

Driver behavior following an automatic steering intervention.

PubMed

Fricke, Nicola; Griesche, Stefan; Schieben, Anna; Hesse, Tobias; Baumann, Martin

2015-10-01

The study investigated driver behavior toward an automatic steering intervention of a collision mitigation system. Forty participants were tested in a driving simulator and confronted with an inevitable collision. They performed a naïve drive and afterwards a repeated exposure in which they were told to hold the steering wheel loosely. In a third drive they experienced a false alarm situation. Data on driving behavior, i.e. steering and braking behavior as well as subjective data was assessed in the scenarios. Results showed that most participants held on to the steering wheel strongly or counter-steered during the system intervention during the first encounter. Moreover, subjective data collected after the first drive showed that the majority of drivers was not aware of the system intervention. Data from the repeated drive in which participants were instructed to hold the steering wheel loosely, led to significantly more participants holding the steering wheel loosely and thus complying with the instruction. This study seems to imply that without knowledge and information of the system about an upcoming intervention, the most prevalent driving behavior is a strong reaction with the steering wheel similar to an automatic steering reflex which decreases the system's effectiveness. Results of the second drive show some potential for countermeasures, such as informing drivers shortly before a system intervention in order to prevent inhibiting reactions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Development of a DC propulsion system for an electric vehicle

NASA Technical Reports Server (NTRS)

Kelledes, W. L.

1984-01-01

The suitability of the Eaton automatically shifted mechanical transaxle concept for use in a near-term dc powered electric vehicle is evaluated. A prototype dc propulsion system for a passenger electric vehicle was designed, fabricated, tested, installed in a modified Mercury Lynx vehicle and track tested at the contractor's site. The system consisted of a two-axis, three-speed, automatically-shifted mechanical transaxle, 15.2 Kw rated, separately excited traction motor, and a transistorized motor controller with a single chopper providing limited armature current below motor base speed and full range field control above base speed at up to twice rated motor current. The controller utilized a microprocessor to perform motor and vehicle speed monitoring and shift sequencing by means of solenoids applying hydraulic pressure to the transaxle clutches. Bench dynamometer and track testing was performed. Track testing showed best system efficiency for steady-state cruising speeds of 65-80 Km/Hz (40-50 mph). Test results include acceleration, steady speed and SAE J227A/D cycle energy consumption, braking tests and coast down to characterize the vehicle road load.

Predicting crash-relevant violations at stop sign-controlled intersections for the development of an intersection driver assistance system.

PubMed

Scanlon, John M; Sherony, Rini; Gabler, Hampton C

2016-09-01

Intersection crashes resulted in over 5,000 fatalities in the United States in 2014. Intersection Advanced Driver Assistance Systems (I-ADAS) are active safety systems that seek to help drivers safely traverse intersections. I-ADAS uses onboard sensors to detect oncoming vehicles and, in the event of an imminent crash, can either alert the driver or take autonomous evasive action. The objective of this study was to develop and evaluate a predictive model for detecting whether a stop sign violation was imminent. Passenger vehicle intersection approaches were extracted from a data set of typical driver behavior (100-Car Naturalistic Driving Study) and violations (event data recorders downloaded from real-world crashes) and were assigned weighting factors based on real-world frequency. A k-fold cross-validation procedure was then used to develop and evaluate 3 hypothetical stop sign warning algorithms (i.e., early, intermediate, and delayed) for detecting an impending violation during the intersection approach. Violation detection models were developed using logistic regression models that evaluate likelihood of a violation at various locations along the intersection approach. Two potential indicators of driver intent to stop-that is, required deceleration parameter (RDP) and brake application-were used to develop the predictive models. The earliest violation detection opportunity was then evaluated for each detection algorithm in order to (1) evaluate the violation detection accuracy and (2) compare braking demand versus maximum braking capabilities. A total of 38 violating and 658 nonviolating approaches were used in the analysis. All 3 algorithms were able to detect a violation at some point during the intersection approach. The early detection algorithm, as designed, was able to detect violations earlier than all other algorithms during the intersection approach but gave false alarms for 22.3% of approaches. In contrast, the delayed detection algorithm sacrificed some time for detecting violations but was able to substantially reduce false alarms to only 3.3% of all nonviolating approaches. Given good surface conditions (maximum braking capabilities = 0.8 g) and maximum effort, most drivers (55.3-71.1%) would be able to stop the vehicle regardless of the detection algorithm. However, given poor surface conditions (maximum braking capabilities = 0.4 g), few drivers (10.5-26.3%) would be able to stop the vehicle. Automatic emergency braking (AEB) would allow for early braking prior to driver reaction. If equipped with an AEB system, the results suggest that, even for the poor surface conditions scenario, over one half (55.3-65.8%) of the vehicles could have been stopped. This study demonstrates the potential of I-ADAS to incorporate a stop sign violation detection algorithm. Repeating the analysis on a larger, more extensive data set will allow for the development of a more comprehensive algorithm to further validate the findings.

Gas-Dynamic Designing of the Exhaust System for the Air Brake

NASA Astrophysics Data System (ADS)

Novikova, Yu; Goriachkin, E.; Volkov, A.

2018-01-01

Each gas turbine engine is tested some times during the life-cycle. The test equipment includes the air brake that utilizes the power produced by the gas turbine engine. In actual conditions, the outlet pressure of the air brake does not change and is equal to atmospheric pressure. For this reason, for the air brake work it is necessary to design the special exhaust system. Mission of the exhaust system is to provide the required level of backpressure at the outlet of the air brake. The backpressure is required for the required power utilization by the air brake (the air brake operation in the required points on the performance curves). The paper is described the development of the gas dynamic canal, designing outlet guide vane and the creation of a unified exhaust system for the air brake. Using a unified exhaust system involves moving the operating point to the performance curve further away from the calculated point. However, the applying of one exhaust system instead of two will significantly reduce the cash and time costs.

Fulfilling the pedestrian protection directive using a long-wavelength infrared camera designed to meet both performance and cost targets

NASA Astrophysics Data System (ADS)

Källhammer, Jan-Erik; Pettersson, Håkan; Eriksson, Dick; Junique, Stéphane; Savage, Susan; Vieider, Christian; Andersson, Jan Y.; Franks, John; Van Nylen, Jan; Vercammen, Hans; Kvisterøy, Terje; Niklaus, Frank; Stemme, Göran

2006-04-01

Pedestrian fatalities are around 15% of the traffic fatalities in Europe. A proposed EU regulation requires the automotive industry to develop technologies that will substantially decrease the risk for Vulnerable Road Users when hit by a vehicle. Automatic Brake Assist systems, activated by a suitable sensor, will reduce the speed of the vehicle before the impact, independent of any driver interaction. Long Wavelength Infrared technology is an ideal candidate for such sensors, but requires a significant cost reduction. The target necessary for automotive serial applications are well below the cost of systems available today. Uncooled bolometer arrays are the most mature technology for Long Wave Infrared with low-cost potential. Analyses show that sensor size and production yield along with vacuum packaging and the optical components are the main cost drivers. A project has been started to design a new Long Wave Infrared system with a ten times cost reduction potential, optimized for the pedestrian protection requirement. It will take advantage of the progress in Micro Electro-Mechanical Systems and Long Wave Infrared optics to keep the cost down. Deployable and pre-impact braking systems can become effective alternatives to passive impact protection systems solutions fulfilling the EU pedestrian protection regulation. Low-cost Long Wave Infrared sensors will be an important enabler to make such systems cost competitive, allowing high market penetration.

The Effect of a Variable Disc Pad Friction Coefficient for the Mechanical Brake System of a Railway Vehicle

PubMed Central

Lee, Nam-Jin; Kang, Chul-Goo

2015-01-01

A brake hardware-in-the-loop simulation (HILS) system for a railway vehicle is widely applied to estimate and validate braking performance in research studies and field tests. When we develop a simulation model for a full vehicle system, the characteristics of all components are generally properly simplified based on the understanding of each component’s purpose and interaction with other components. The friction coefficient between the brake disc and the pad used in simulations has been conventionally considered constant, and the effect of a variable friction coefficient is ignored with the assumption that the variability affects the performance of the vehicle braking very little. However, the friction coefficient of a disc pad changes significantly within a range due to environmental conditions, and thus, the friction coefficient can affect the performance of the brakes considerably, especially on the wheel slide. In this paper, we apply a variable friction coefficient and analyzed the effects of the variable friction coefficient on a mechanical brake system of a railway vehicle. We introduce a mathematical formula for the variable friction coefficient in which the variable friction is represented by two variables and five parameters. The proposed formula is applied to real-time simulations using a brake HILS system, and the effectiveness of the formula is verified experimentally by testing the mechanical braking performance of the brake HILS system. PMID:26267883

The Effect of a Variable Disc Pad Friction Coefficient for the Mechanical Brake System of a Railway Vehicle.

PubMed

Lee, Nam-Jin; Kang, Chul-Goo

2015-01-01

A brake hardware-in-the-loop simulation (HILS) system for a railway vehicle is widely applied to estimate and validate braking performance in research studies and field tests. When we develop a simulation model for a full vehicle system, the characteristics of all components are generally properly simplified based on the understanding of each component's purpose and interaction with other components. The friction coefficient between the brake disc and the pad used in simulations has been conventionally considered constant, and the effect of a variable friction coefficient is ignored with the assumption that the variability affects the performance of the vehicle braking very little. However, the friction coefficient of a disc pad changes significantly within a range due to environmental conditions, and thus, the friction coefficient can affect the performance of the brakes considerably, especially on the wheel slide. In this paper, we apply a variable friction coefficient and analyzed the effects of the variable friction coefficient on a mechanical brake system of a railway vehicle. We introduce a mathematical formula for the variable friction coefficient in which the variable friction is represented by two variables and five parameters. The proposed formula is applied to real-time simulations using a brake HILS system, and the effectiveness of the formula is verified experimentally by testing the mechanical braking performance of the brake HILS system.

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces. A slip-velocity-controlled, pressure-bias-modulated system

NASA Technical Reports Server (NTRS)

Stubbs, S. M.; Tanner, J. A.; Smith, E. G.

1979-01-01

The braking and cornering response of a slip velocity controlled, pressure bias modulated aircraft antiskid braking system is investigated. The investigation, conducted on dry and wet runway surfaces, utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC 9 series 10 airplane. The landing gear strut was replaced by a dynamometer. The parameters, which were varied, included the carriage speed, tire loading, yaw angle, tire tread condition, brake system operating pressure, and runway wetness conditions. The effects of each of these parameters on the behavior of the skid control system is presented. Comparisons between data obtained with the skid control system and data obtained from single cycle braking tests without antiskid protection are examined.

49 CFR 238.431 - Brake system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... dynamic brake does not result in exceeding the allowable stopping distance; (2) The friction brake alone... speed for safe operation of the train using only the friction brake portion of the blended brake with no...

49 CFR 238.431 - Brake system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... dynamic brake does not result in exceeding the allowable stopping distance; (2) The friction brake alone... speed for safe operation of the train using only the friction brake portion of the blended brake with no...

49 CFR 238.431 - Brake system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... dynamic brake does not result in exceeding the allowable stopping distance; (2) The friction brake alone... speed for safe operation of the train using only the friction brake portion of the blended brake with no...

Operator interface for vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bissontz, Jay E

2015-03-10

A control interface for drivetrain braking provided by a regenerative brake and a non-regenerative brake is implemented using a combination of switches and graphic interface elements. The control interface comprises a control system for allocating drivetrain braking effort between the regenerative brake and the non-regenerative brake, a first operator actuated control for enabling operation of the drivetrain braking, and a second operator actuated control for selecting a target braking effort for drivetrain braking. A graphic display displays to an operator the selected target braking effort and can be used to further display actual braking effort achieved by drivetrain braking.

IR-camera methods for automotive brake system studies

NASA Astrophysics Data System (ADS)

Dinwiddie, Ralph B.; Lee, Kwangjin

1998-03-01

Automotive brake systems are energy conversion devices that convert kinetic energy into heat energy. Several mechanisms, mostly related to noise and vibration problems, can occur during brake operation and are often related to non-uniform temperature distribution on the brake disk. These problems are of significant cost to the industry and are a quality concern to automotive companies and brake system vendors. One such problem is thermo-elastic instabilities in brake system. During the occurrence of these instabilities several localized hot spots will form around the circumferential direction of the brake disk. The temperature distribution and the time dependence of these hot spots, a critical factor in analyzing this problem and in developing a fundamental understanding of this phenomenon, were recorded. Other modes of non-uniform temperature distributions which include hot banding and extreme localized heating were also observed. All of these modes of non-uniform temperature distributions were observed on automotive brake systems using a high speed IR camera operating in snap-shot mode. The camera was synchronized with the rotation of the brake disk so that the time evolution of hot regions could be studied. This paper discusses the experimental approach in detail.

Recent studies of tire braking performance. [for aircraft

NASA Technical Reports Server (NTRS)

Mccarty, J. L.; Leland, T. J. W.

1973-01-01

The results from recent studies of some factors affecting tire braking and cornering performance are presented together with a discussion of the possible application of these results to the design of aircraft braking systems. The first part of the paper is concerned with steady-state braking, that is, results from tests conducted at a constant slip ratio or steering angle or both. The second part deals with cyclic braking tests, both single cycle, where brakes are applied at a constant rate until wheel lockup is achieved, and rapid cycling of the brakes under control of a currently operational antiskid system.

Talking about the Automobile Braking System

NASA Astrophysics Data System (ADS)

Xu, Zhiqiang

2017-12-01

With the continuous progress of society, the continuous development of the times, people’s living standards continue to improve, people continue to improve the pursuit. With the rapid development of automobile manufacturing, the car will be all over the tens of thousands of households, the increase in car traffic, a direct result of the incidence of traffic accidents. Brake system is the guarantee of the safety of the car, its technical condition is good or bad, directly affect the operational safety and transportation efficiency, so the brake system is absolutely reliable. The requirements of the car on the braking system is to have a certain braking force to ensure reliable work in all cases, light and flexible operation. Normal braking should be good performance, in addition to a foot sensitive, the emergency brake four rounds can not be too long, not partial, not ring.

Research on squeal noise of tread brake system in rail freight vehicle

NASA Astrophysics Data System (ADS)

Zhang, Jun; Li, Yong-hua; Fang, Ji; Zhao, Wen-zhong

2017-07-01

Brake squeal is a result of a unstable flutter from brake system, it results to the noise pollution in railway side and excessive wear of wheel tread. A finite element model of brake system for rail freight vehicle is set up, the contact and friction between the brake shoe and wheel tread is considered, the complex modals of brake system are calculated, the possibility of happening chatter and squeal noise are analyzed. The results show that the pressure angle or the brake force direction have a important influence on the unstable chatter and squeal noise, the more greater the pressure angle deviates from the wheel center, the more greater the possibility of happening chatter and squeal noise is, and the possibility of happening chatter and squeal noise is also increased along with the addition of friction factor.

A design study for a simple-to-fly, constant attitude light aircraft

NASA Technical Reports Server (NTRS)

Smetana, F. O.; Humphreys, D. E.; Montoya, R. J.; Rickard, W. W.; Wilkinson, I. E.

1973-01-01

The activities during a four-year study by doctoral students to evolve in detail a design for a simple-to-fly, constant attitude light airplane are described. The study indicated that such aircraft could materially reduce the hazards to light airplane occupants which arise from the high pilot work load and poor visibility that occur during landing. Preliminary cost studies indicate that in volume production this system would increase the cost of the aircraft in roughly the same fashion that automatic transmission, power steering, power brakes, and cruise control increase the cost of a compact car.

Run-Curve Design for Energy Saving Operation in a Modern DC-Electrification

NASA Astrophysics Data System (ADS)

Koseki, Takafumi; Noda, Takashi

Mechanical brakes are often used by electric trains. These brakes have a few problems like response speed, coefficient of friction, maintenance cost and so on. As a result, methods for actively using regenerative brakes are required. In this paper, we propose the useful pure electric braking, which would involve ordinary brakes by only regenerative brakes without any mechanical brakes at high speed. Benefits of our proposal include a DC-electrification system with regenerative substations that can return powers to the commercial power system and a train that can use the full regenerative braking force. We furthermore evaluate the effects on running time and energies saved by regenerative substations in the proposed method.

30 CFR 77.1403 - Daily examination of hoisting equipment.

Code of Federal Regulations, 2014 CFR

2014-07-01

...: (a) Elevators. (1) A visual examination of the ropes for wear, broken wires, and corrosion.... (1) An examination of the rope fastenings for defects; (2) An examination of sheaves for broken... automatic controls and brakes required under § 77.1401. (Sec. 101, Federal Mine Safety and Health Act of...

30 CFR 77.1403 - Daily examination of hoisting equipment.

Code of Federal Regulations, 2013 CFR

2013-07-01

...: (a) Elevators. (1) A visual examination of the ropes for wear, broken wires, and corrosion.... (1) An examination of the rope fastenings for defects; (2) An examination of sheaves for broken... automatic controls and brakes required under § 77.1401. (Sec. 101, Federal Mine Safety and Health Act of...

30 CFR 77.1403 - Daily examination of hoisting equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

...: (a) Elevators. (1) A visual examination of the ropes for wear, broken wires, and corrosion.... (1) An examination of the rope fastenings for defects; (2) An examination of sheaves for broken... automatic controls and brakes required under § 77.1401. (Sec. 101, Federal Mine Safety and Health Act of...

30 CFR 77.1403 - Daily examination of hoisting equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

...: (a) Elevators. (1) A visual examination of the ropes for wear, broken wires, and corrosion.... (1) An examination of the rope fastenings for defects; (2) An examination of sheaves for broken... automatic controls and brakes required under § 77.1401. (Sec. 101, Federal Mine Safety and Health Act of...

30 CFR 77.1403 - Daily examination of hoisting equipment.

Code of Federal Regulations, 2012 CFR

2012-07-01

...: (a) Elevators. (1) A visual examination of the ropes for wear, broken wires, and corrosion.... (1) An examination of the rope fastenings for defects; (2) An examination of sheaves for broken... automatic controls and brakes required under § 77.1401. (Sec. 101, Federal Mine Safety and Health Act of...

Evaluation the course of the vehicle braking process in case of hydraulic circuit malfunction

NASA Astrophysics Data System (ADS)

Szczypiński-Sala, W.; Lubas, J.

2016-09-01

In the paper, the results of the research were discussed, the aim of which was the evaluation of the vehicle braking performance efficiency and the course of this process with regard to the dysfunction which may occur in braking hydraulic circuit. As part of the research, on-road tests were conducted. During the research, the delay of the vehicle when braking was measured with the use of the set of sensors placed in the parallel and the perpendicular axis of the vehicle. All the tests were conducted on the same flat section of asphalt road with wet surface. Conditions of diminished tire-to-road adhesion were chosen in order to force the activity of anti-lock braking system. The research was conducted comparatively for the vehicle with acting anti-lock braking system and subsequently for the vehicle without the system. In both cases, there was a subsequent evaluation of the course of braking with efficient braking system and with the dysfunction of hydraulic circuit.

Modelling and validation of magnetorheological brake responses using parametric approach

NASA Astrophysics Data System (ADS)

Z, Zainordin A.; A, Abdullah M.; K, Hudha

2013-12-01

Magnetorheological brake (MR Brake) is one x-by-wire systems which performs better than conventional brake systems. MR brake consists of a rotating disc that is immersed with Magnetorheological Fluid (MR Fluid) in an enclosure of an electromagnetic coil. The applied magnetic field will increase the yield strength of the MR fluid where this fluid was used to decrease the speed of the rotating shaft. The purpose of this paper is to develop a mathematical model to represent MR brake with a test rig. The MR brake model is developed based on actual torque characteristic which is coupled with motion of a test rig. Next, the experimental are performed using MR brake test rig and obtained three output responses known as angular velocity response, torque response and load displacement response. Furthermore, the MR brake was subjected to various current. Finally, the simulation results of MR brake model are then verified with experimental results.

29 CFR 1926.601 - Motor vehicles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... that operate within an off-highway jobsite, not open to public traffic. The requirements of this.... (1) All vehicles shall have a service brake system, an emergency brake system, and a parking brake... vehicles, or combination of vehicles, shall have brake lights in operable condition regardless of light...

Aspects regarding manufacturing technologies of composite materials for brake pad application

NASA Astrophysics Data System (ADS)

Craciun, A. L.; Hepuţ, T.; Pinca-Bretotean, C.

2018-01-01

Current needs in road safety, requires the development of new technical solutions for automotive braking system. Their safe operation is subject to following factors: concept design, materials used and electronic control. Among the factors previously listed, choice of materials and manufacturing processes are difficult stage but very important for achieving technical performance and getting a relatively small cost of constituting parts of brake system. The choice is based on the promotion of organic composite material, popular in areas where the weight of materials plays an important role. The brake system is composed of many different parts including brake pads, a master cylinder, wheel cylinders and a hydraulic control system. The brake pads are an important component in the braking system of automotive. These are of different types, suitable for different types of automotive and engines. Brake pads are designed for friction stability, durability, minimization of noise and vibration. The typology of the brake pads depends on the material which they are made. The aim of this paper is to presents the manufacturing technologies for ten recipes of composite material used in brake pads applications. In this work will be done: choosing the constituents of the recipes, investigation of their basic characteristics, setting the proportions of components, obtaining the composite materials in laboratory, establishing the parameters of manufacturing technology and technological analysis.

Regenerative braking system of PM synchronous motor

NASA Astrophysics Data System (ADS)

Gao, Qian; Lv, Chengxing; Zhao, Na; Zang, Hechao; Jiang, Huilue; Zhang, Zhaowen; Zhang, Fengli

2018-04-01

Permanent-magnet synchronous motor is widely adopted in many fields with the advantage of a high efficiency and a high torque density. Regenerative Braking Systems (RBS) provide an efficient method to assist PMSM system achieve better fuel economy and lowering exhaust emissions. This paper describes the design and testing of the regenerative braking systems of PMSM. The mode of PWM duty has been adjusted to control regenerative braking of PMSM using energy controller for the port-controlled Hamiltonian model. The simulation analysis indicates that a smooth control could be realized and the highest efficiency and the smallest current ripple could be achieved by Regenerative Braking Systems.

49 CFR 232.109 - Dynamic brake requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... system that includes dynamic brakes shall adopt and comply with written operating rules governing safe... verifiable data and research. (k) A railroad operating a train with a brake system that includes dynamic... 49 Transportation 4 2010-10-01 2010-10-01 false Dynamic brake requirements. 232.109 Section 232...

Impulsive response of an automatic transmission system with multiple clearances: Formulation, simulation and experiment

NASA Astrophysics Data System (ADS)

Crowther, Ashley R.; Singh, Rajendra; Zhang, Nong; Chapman, Chris

2007-10-01

Impulsive responses in geared systems with multiple clearances are studied when the mean torque excitation and system load change abruptly, with application to a vehicle driveline with an automatic transmission. First, torsional lumped-mass models of the planetary and differential gear sets are formulated using matrix elements. The model is then reduced to address tractable nonlinear problems while successfully retaining the main modes of interest. Second, numerical simulations for the nonlinear model are performed for transient conditions and a typical driving situation that induces an impulsive behaviour simulated. However, initial conditions and excitation and load profiles have to be carefully defined before the model can be numerically solved. It is shown that the impacts within the planetary or differential gears may occur under combinations of engine, braking and vehicle load transients. Our analysis shows that the shaping of the engine transient by the torque converter before reaching the clearance locations is more critical. Third, a free vibration experiment is developed for an analogous driveline with multiple clearances and three experiments that excite different response regimes have been carried out. Good correlations validate the proposed methodology.

Cost Analysis of Utilizing Electric Vehicles and Photovoltaic Solar Energy in the United States Marine Corps Commercial Vehicle Fleet

DTIC Science & Technology

2009-12-01

vehicles so do some electric vehicle braking systems (MIT, 2008). e. Brakes Regenerative braking on electric vehicles recoups some of the energy lost...engine is required to replace the energy lost by braking . Regenerative braking takes some of the lost energy during braking and turns it into...Motors and Tesla Motors offer regenerative breaking in their respective electric vehicles. Tesla explains regenerative braking as “engine braking

Braking System Integration in Dual Mode Systems

DOT National Transportation Integrated Search

1974-05-01

An optimal braking system for Dual Mode is a complex product of vast number of multivariate, interdependent parameters that encompass on-guideway and off-guideway operation as well as normal and emergency braking. : Details of, and interralations amo...

The CRREL Instrumented Vehicle: Hardware and Software.

DTIC Science & Technology

1983-01-01

rear axle torque are meas- ured. The vehicle is equipped for front-wheel, rear-wheel or four-wheel drive. A dual brake system allows front-, rear- or...four-wheel braking . A minicomputer- based data acquisition system is installed in the vehicle to control data gather ing and to process the data. The...o..o...o 4 4. Dual brake system control valves . ........ 5 5. Schematic of modified brake system ...... .... st 5 6. Air-shock-absorber regulator

Transportability

DTIC Science & Technology

2013-04-25

wheel (distance, brake stopping) ± 0.1 m (± 0.3 ft) Walking wheel (distance, road) ± 0.1 km (± 0.06 mile) Speedometer (speed) ± 0.1 km/hr...to impact or at the point of impact if feasible. c. Position the stationary railcar(s) with its coupler compressed and its air and hand brakes ...the prevailing wind. Engage the parking brakes on vehicles, trailers or weapon systems equipped with parking brake systems. Secure loose brake lines

An Instructor's Guide for a Program in Brake Services.

ERIC Educational Resources Information Center

New York State Education Dept., Albany. Bureau of Secondary Curriculum Development.

The instructor's guide is designed to present an understanding of the automotive hydraulic brake system and to help individuals develop new skills for employment in this specialized field of automotive service. Applicable for secondary or adult education, this guide describes: the brake system, types of brakes, diagnosis and correction of brake…

49 CFR 570.6 - Brake power unit.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 6 2011-10-01 2011-10-01 false Brake power unit. 570.6 Section 570.6... Pounds or Less § 570.6 Brake power unit. (a) Vacuum hoses shall not be collapsed, abraded, broken... power assist system. This test is not applicable to vehicles equipped with full power brake system as...

49 CFR 393.48 - Brakes to be operative.

Code of Federal Regulations, 2010 CFR

2010-10-01

... motor vehicle may be equipped with a device to reduce the front wheel braking effort (or in the case of... operable by the driver except upon application of the control that activates the braking system. The device... with air brakes) or 85 percent of the maximum system pressure (for vehicles which are not equipped with...

Extended-Kalman-filter-based regenerative and friction blended braking control for electric vehicle equipped with axle motor considering damping and elastic properties of electric powertrain

NASA Astrophysics Data System (ADS)

Lv, Chen; Zhang, Junzhi; Li, Yutong

2014-11-01

Because of the damping and elastic properties of an electrified powertrain, the regenerative brake of an electric vehicle (EV) is very different from a conventional friction brake with respect to the system dynamics. The flexibility of an electric drivetrain would have a negative effect on the blended brake control performance. In this study, models of the powertrain system of an electric car equipped with an axle motor are developed. Based on these models, the transfer characteristics of the motor torque in the driveline and its effect on blended braking control performance are analysed. To further enhance a vehicle's brake performance and energy efficiency, blended braking control algorithms with compensation for the powertrain flexibility are proposed using an extended Kalman filter. These algorithms are simulated under normal deceleration braking. The results show that the brake performance and blended braking control accuracy of the vehicle are significantly enhanced by the newly proposed algorithms.

Hybrid: Braking

Science.gov Websites

automatically. Go back… stage graphic: vertical blue rule Main stage: See through car with battery, engine, and electric motor visible. The car is stopped at an intersection. Main stage: See through car with battery , engine, and electric motor visible. The car is stopped at an intersection. Battery: The battery stores

49 CFR 571.123 - Standard No. 123; Motorcycle controls and displays.

Code of Federal Regulations, 2013 CFR

2013-10-01

...'s right hand from the throttle. Each control located on a left handlebar shall be operable by the operator's left hand throughout its full range without removal of the operator's left hand from the... rear brake control, the control shall be located on the left handlebar. If a scooter with an automatic...

49 CFR 571.123 - Standard No. 123; Motorcycle controls and displays.

Code of Federal Regulations, 2011 CFR

2011-10-01

...'s right hand from the throttle. Each control located on a left handlebar shall be operable by the operator's left hand throughout its full range without removal of the operator's left hand from the... rear brake control, the control shall be located on the left handlebar. If a scooter with an automatic...

49 CFR 571.123 - Standard No. 123; Motorcycle controls and displays.

Code of Federal Regulations, 2012 CFR

2012-10-01

...'s right hand from the throttle. Each control located on a left handlebar shall be operable by the operator's left hand throughout its full range without removal of the operator's left hand from the... rear brake control, the control shall be located on the left handlebar. If a scooter with an automatic...

49 CFR 571.123 - Standard No. 123; Motorcycle controls and displays.

Code of Federal Regulations, 2014 CFR

2014-10-01

...'s right hand from the throttle. Each control located on a left handlebar shall be operable by the operator's left hand throughout its full range without removal of the operator's left hand from the... rear brake control, the control shall be located on the left handlebar. If a scooter with an automatic...

Performance of an aircraft tire under cyclic braking and of a currently operational antiskid braking system

NASA Technical Reports Server (NTRS)

Tanner, J. A.

1972-01-01

An experimental investigation was conducted to study the performance of an aircraft tire under cyclic braking conditions and to study the performance of a currently operational aircraft antiskid braking system. Dry, damp, and flooded runway surface conditions were used in the investigation. The results indicated that under cyclic braking conditions the braking and cornering-force friction coefficients may be influenced by fluctuations in the vertical load, flexibility in the wheel support, and the spring coupling between the wheel and the tire-pavement interface. The cornering capability was shown to be negligible at wheel slip ratios well below a locked-wheel skid under all test surface conditions. The maximum available brake-force friction coefficient was shown to be dependent upon the runway surface condition, upon velocity, and, for wet runways, upon tire differences. Moderate reductions in vertical load and brake system pressure did not significantly affect the overall wet-runway performance of the tire.

Analysis of heat conduction in a drum brake system of the wheeled armored personnel carriers

NASA Astrophysics Data System (ADS)

Puncioiu, A. M.; Truta, M.; Vedinas, I.; Marinescu, M.; Vinturis, V.

2015-11-01

This paper is an integrated study performed over the Braking System of the Wheeled Armored Personnel Carriers. It mainly aims to analyze the heat transfer process which is present in almost any industrial and natural process. The vehicle drum brake systems can generate extremely high temperatures under high but short duration braking loads or under relatively light but continuous braking. For the proper conduct of the special vehicles mission in rough terrain, we are talking about, on one hand, the importance of the possibility of immobilization and retaining position and, on the other hand, during the braking process, the importance movement stability and reversibility or reversibility, to an encounter with an obstacle. Heat transfer processes influence the performance of the braking system. In the braking phase, kinetic energy transforms into thermal energy resulting in intense heating and high temperature states of analyzed vehicle wheels. In the present work a finite element model for the temperature distribution in a brake drum is developed, by employing commercial finite element software, ANSYS. These structural and thermal FEA models will simulate entire braking event. The heat generated during braking causes distortion which modifies thermoelastic contact pressure distribution drum-shoe interface. In order to capture the effect of heat, a transient thermal analysis is performed in order to predict the temperature distribution transitional brake components. Drum brakes are checked both mechanical and thermal. These tests aim to establish their sustainability in terms of wear and the variation coefficient of friction between the friction surfaces with increasing temperature. Modeling using simulation programs led eventually to the establishment of actual thermal load of the mechanism of brake components. It was drawn the efficiency characteristic by plotting the coefficient of effectiveness relative to the coefficient of friction shoe-drum. Thus induced thermal loads determine thermo mechanical behavior of the structure of wheels. Study the transfer of heat generated during braking is useful because results can improve and validate existing theory or may lead to the development of a mathematical model to simulate the behavior of the brake system for various tactical and operational situations. Conclusions of this paper are relevant because theoretical data analysis results are validated by experimental research.

Heavy and Overweight Vehicle Brake Testing: Five-Axle Combination Tractor-Flatbed Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lascurain, Mary Beth; Capps, Gary J; Franzese, Oscar

The Federal Motor Carrier Safety Administration, in coordination with the Federal Highway Administration, sponsored the Heavy and Overweight Vehicle Brake Testing (HOVBT) program in order to provide information about the effect of gross vehicle weight (GVW) on braking performance. Because the Federal Motor Carrier Safety Regulations limit the number of braking system defects that may exist for a vehicle to be allowed to operate on the roadways, the examination of the effect of brake defects on brake performance for increased loads is also relevant. The HOVBT program seeks to provide relevant information to policy makers responsible for establishing load limits,more » beginning with providing test data for a combination tractor/trailer. This testing was conducted on a five-axle combination vehicle with tractor brakes meeting the Reduced Stopping Distance requirement rulemaking. This report provides a summary of the testing activities, the results of various analyses of the data, and recommendations for future research. Following a complete brake rebuild, instrumentation, and brake burnish, stopping tests were performed from 20 and 40 mph with various brake application pressures (15 psi, 25 psi, 35 psi, 45 psi, 55 psi, and full system pressure). These tests were conducted for various brake conditions at the following GVWs: 60,000, 80,000, 91,000, 97,000, 106,000, and 116,000 lb. The 80,000-lb GVWs included both balanced and unbalanced loads. The condition of the braking system was also varied. To introduce these defects, brakes (none, forward drive axle, or rear trailer axle) were made inoperative. In addition to the stopping tests, performance-based brake tests were conducted for the various loading and brake conditions. Analysis of the stopping test data showed the stopping distance to increase with load (as expected) and also showed that more braking force was generated by the drive axle brakes than the trailer axle brakes. The constant-pressure stopping test data revealed a linear relationship between brake application pressure and was used to develop an algorithm to normalize stopping data for weight and initial speed.« less

49 CFR 232.103 - General requirements for all train brake systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... pneumatic technology, the integrity of the train line shall be monitored by the brake control system. (c) A... train shall not move if less than 85 percent of the cars in that train have operative and effective brakes. (f) Each car in a train shall have its air brakes in effective operating condition unless the car...

49 CFR 570.5 - Service brake system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... force applied by the brake on a front wheel or a rear wheel shall not differ by more than 20 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i... Pounds or Less § 570.5 Service brake system. Unless otherwise noted, the force to be applied during...

49 CFR 570.5 - Service brake system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... force applied by the brake on a front wheel or a rear wheel shall not differ by more than 20 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i... Pounds or Less § 570.5 Service brake system. Unless otherwise noted, the force to be applied during...

49 CFR 570.5 - Service brake system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... force applied by the brake on a front wheel or a rear wheel shall not differ by more than 20 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i... Pounds or Less § 570.5 Service brake system. Unless otherwise noted, the force to be applied during...

49 CFR 232.205 - Class I brake test-initial terminal inspection.

Code of Federal Regulations, 2012 CFR

2012-10-01

... test shall be conducted as follows: (A) Charge the air brake system to the pressure at which the train... equivalent pressure maintaining locomotive brake valve, a railroad may use the Air Flow Method Test as an...) Charge the air brake system to the pressure at which the train will be operated, and the pressure at the...

49 CFR 232.205 - Class I brake test-initial terminal inspection.

Code of Federal Regulations, 2014 CFR

2014-10-01

... test shall be conducted as follows: (A) Charge the air brake system to the pressure at which the train... equivalent pressure maintaining locomotive brake valve, a railroad may use the Air Flow Method Test as an...) Charge the air brake system to the pressure at which the train will be operated, and the pressure at the...

49 CFR 232.205 - Class I brake test-initial terminal inspection.

Code of Federal Regulations, 2011 CFR

2011-10-01

... test shall be conducted as follows: (A) Charge the air brake system to the pressure at which the train... equivalent pressure maintaining locomotive brake valve, a railroad may use the Air Flow Method Test as an...) Charge the air brake system to the pressure at which the train will be operated, and the pressure at the...

49 CFR 232.205 - Class I brake test-initial terminal inspection.

Code of Federal Regulations, 2013 CFR

2013-10-01

... test shall be conducted as follows: (A) Charge the air brake system to the pressure at which the train... equivalent pressure maintaining locomotive brake valve, a railroad may use the Air Flow Method Test as an...) Charge the air brake system to the pressure at which the train will be operated, and the pressure at the...

Brake reactions of distracted drivers to pedestrian Forward Collision Warning systems.

PubMed

Lubbe, Nils

2017-06-01

Forward Collision Warning (FCW) can be effective in directing driver attention towards a conflict and thereby aid in preventing or mitigating collisions. FCW systems aiming at pedestrian protection have been introduced onto the market, yet an assessment of their safety benefits depends on the accurate modeling of driver reactions when the system is activated. This study contributes by quantifying brake reaction time and brake behavior (deceleration levels and jerk) to compare the effectiveness of an audio-visual warning only, an added haptic brake pulse warning, and an added Head-Up Display in reducing the frequency of collisions with pedestrians. Further, this study provides a detailed data set suited for the design of assessment methods for car-to-pedestrian FCW systems. Brake response characteristics were measured for heavily distracted drivers who were subjected to a single FCW event in a high-fidelity driving simulator. The drivers maintained a self-regulated speed of 30km/h in an urban area, with gaze direction diverted from the forward roadway by a secondary task. Collision rates and brake reaction times differed significantly across FCW settings. Brake pulse warnings resulted in the lowest number of collisions and the shortest brake reaction times (mean 0.8s, SD 0.29s). Brake jerk and deceleration were independent of warning type. Ninety percent of drivers exceeded a maximum deceleration of 3.6m/s 2 and a jerk of 5.3m/s 3 . Brake pulse warning was the most effective FCW interface for preventing collisions. In addition, this study presents the data required for driver modeling for car-to-pedestrian FCW similar to Euro NCAP's 2015 car-to-car FCW assessment. Practical applications: Vehicle manufacturers should consider the introduction of brake pulse warnings to their FCW systems. Euro NCAP could introduce an assessment that quantifies the safety benefits of pedestrian FCW systems and thereby aid the proliferation of effective systems. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

Development of friction material by using precast prefired (pcp f) blocks

NASA Astrophysics Data System (ADS)

Dineshkumar, R.; Ramanamurthy, E. V. V.; Krishnapavanteja, Ch

2017-05-01

The braking system used to control and stop automobile system. The braking system converts the kinematic energy into heat energy by friction. The performance of the brake pad depends on composition of friction materials. The asbestos brake pads are carcinogenic nature and it makes so many health problems. The present research work is going to replacement of asbestos by new materials. The new material is made by fused ceramic materials from industrial wastage. In this study the industrial waste are recycled and conducted the suitable test to compare the performance of the new material with existing brake pad material. The wear test was conducted by pin on disc experiment. The non asbestos, nonfused, fused samples are represented by x1, x2 and x3. The new brake pad material is formed by non fused and fused ceramic materials. The brake pads are manufactured by powder compacting process.

In-depth analysis of bicycle hydraulic disc brakes

NASA Astrophysics Data System (ADS)

Maier, Oliver; Györfi, Benedikt; Wrede, Jürgen; Arnold, Timo; Moia, Alessandro

2017-10-01

Hydraulic Disc Brakes (HDBs) represent the most recent and innovative bicycle braking system. Especially Electric Bicycles (EBs), which are becoming more and more popular, are equipped with this powerful, unaffected by environmental influences, and low-wear type of brakes. As a consequence of the high braking performance, typical bicycle braking errors lead to more serious accidents. This is the starting point for the development of a Braking Dynamics Assistance system (BDA) to prevent front wheel lockup and nose-over (falling over the handlebars). One of the essential prerequisites for the system design is a better understanding of bicycle HDBs' characteristics. A physical simulation model and a test bench have been built for this purpose. The results of the virtual and real experiments conducted show a high correlation and allow valuable insights into HDBs on bicycles, which have not been studied scientifically in any depth so far.

49 CFR 229.13 - Control of locomotives.

Code of Federal Regulations, 2010 CFR

2010-10-01

... coupled in remote or multiple control, the propulsion system, the sanders, and the power brake system of each locomotive shall respond to control from the cab of the controlling locomotive. If a dynamic brake or regenerative brake system is in use, that portion of the system in use shall respond to control...

49 CFR 232.602 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF TRANSPORTATION BRAKE SYSTEM SAFETY STANDARDS FOR FREIGHT AND OTHER NON-PASSENGER TRAINS AND EQUIPMENT; END-OF-TRAIN DEVICES Electronically Controlled Pneumatic (ECP) Braking Systems § 232.602... this part and equipped with an ECP brake system. Unless specifically excepted or modified in this...

Defense Logistics Agency Did Not Obtain Fair and Reasonable Prices From Meggitt Aircraft Braking Systems for Sole-Source Commercial Spare Parts (REDACTED)

DTIC Science & Technology

2015-05-08

Defense Logistics Agency Did Not Obtain Fair and Reasonable Prices From Meggitt Aircraft Braking Systems for Sole-Source Commercial Spare Parts...Defense Logistics Agency Did Not Obtain Fair and Reasonable Prices From Meggitt Aircraft Braking Systems for Sole-Source Commercial Spare Parts...D000AH-0180.000) │ i Results in Brief Defense Logistics Agency Did Not Obtain Fair and Reasonable Prices From Meggitt Aircraft Braking Systems for

78 FR 3363 - Airworthiness Directives; the Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-16

...-mechanical brake flex shaft (short flexshaft) of the thrust reverser actuation system (TRAS). This proposed... the electro-mechanical brake and center drive unit (CDU) cone brake to verify the holding torque, and... describes a functional test of the electro-mechanical brake and CDU cone brake to verify the holding torque...

49 CFR 383.95 - Restrictions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... applicant either fails the air brake component of the knowledge test, or performs the skills test in a... the skills test and the restriction, air brakes include any braking system operating fully or partially on the air brake principle. (b) Full air brake. (1) If an applicant performs the skills test in a...

49 CFR 238.231 - Brake system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... by testing or previous service. (h) Hand brakes and parking brakes. (1) Except for a locomotive that..., and except for MU locomotives, all locomotives shall be equipped with a hand or parking brake that can... locomotives, on locomotives so equipped, the hand or parking brake as well as its parts and connections shall...

49 CFR 238.231 - Brake system.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Equipped with brake indicators as defined in § 238.5, designed so that the pressure sensor is placed in a... alcohol or other chemicals into the air brake system of passenger equipment is prohibited. (f) The...

49 CFR 238.231 - Brake system.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Equipped with brake indicators as defined in § 238.5, designed so that the pressure sensor is placed in a... alcohol or other chemicals into the air brake system of passenger equipment is prohibited. (f) The...

49 CFR 238.231 - Brake system.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Equipped with brake indicators as defined in § 238.5, designed so that the pressure sensor is placed in a... alcohol or other chemicals into the air brake system of passenger equipment is prohibited. (f) The...

49 CFR 232.605 - Training requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF TRANSPORTATION BRAKE SYSTEM SAFETY STANDARDS FOR FREIGHT AND OTHER NON-PASSENGER TRAINS AND EQUIPMENT; END-OF-TRAIN DEVICES Electronically Controlled Pneumatic (ECP) Braking Systems § 232.605 Training... equipped with an ECP brake system and each contractor that performs inspection, testing, or maintenance on...

49 CFR 229.53 - Brake gauges.

Code of Federal Regulations, 2010 CFR

2010-10-01

... TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Safety Requirements Brake System § 229.53 Brake gauges. All... engineer to aid in the control or braking of the train or locomotive shall be located so that they may be...

Engineering report. Part 3: NASA lightweight wheel and brake sub-system. Lightweight brake development. [for application to space shuttle

NASA Technical Reports Server (NTRS)

Bok, L. D.

1973-01-01

The development of light weight wheel and brake systems designed to meet the space shuttle type requirements was investigated. The study includes the use of carbon graphite composite and beryllium as heat sink materials and the compatibility of these heat sink materials with the other structural components of the wheel and brake.

Brake control system modification, augmentor Wing Jet STOL Research Airplane (AWJSRA)

NASA Technical Reports Server (NTRS)

Amberg, R. L.; Arline, J. A.; Jenny, R. W.

1974-01-01

The braking system for a short takeoff aircraft is discussed and the deficiencies are described. The installation of a Boeing 727 aircraft brake system was made to correct the deficiencies. Tests of the modified system were conducted using an analog computer/hardware simulator. Actual performance tests were conducted and the characteristics of the system were satisfactory.

Investigations upon the effects of an auxiliary brake system on the working parameters of diesel engines

NASA Astrophysics Data System (ADS)

Suciu, Cornel; Mihai, Ioan

2016-12-01

Classical systems have the main disadvantage of being unable to ensure that high load diesel engine vehicles are slowed in good conditions, for the entire range of combinations of inclinations and lengths of sloped public roads. On such roads, where brakes are used repeatedly and for long periods, friction components that enter classical braking systems will overheat and lead to failure. The present paper aims to investigate, the efficiency of a braking system based on compression release, called a Jake Brake. In such a system, the exhaust valve is actuated at a certain predetermined angle of the crankshaft. The presented research was conducted on an experimental rig based on a four-stroke mono-cylinder diesel engine model Lombardini 6 LD400. Pressure and temperature evolutions were monitored before and during the use of the Jake Brake system. As the generated phonic pollution is the main disadvantage of such systems, noise generated in the vicinity of the engine was monitored as well. The monitored parameters were then plotted in diagrams that allowed evaluating the performances of the system.

49 CFR 393.49 - Control valves for brakes.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., which is equipped with power brakes, must have the braking system so arranged that one application valve must when activated cause all of the service brakes on the motor vehicle or combination motor vehicle... with an additional valve to be used to operate the brakes on a trailer or trailers or as required for...

77 FR 63712 - Airworthiness Directives; Piaggio Aero Industries S.p.A.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-17

... authority for Italy. We issued that AD to prevent the brake hydraulic fluid from leaking because of the brake assembly rods contacting the brake valve tubing, which could result in the inability to adequately... brake pads between pilot and copilot, a brake system rod was found deflected. The rod, in this bent...

Creation of operation algorithms for combined operation of anti-lock braking system (ABS) and electric machine included in the combined power plant

NASA Astrophysics Data System (ADS)

Bakhmutov, S. V.; Ivanov, V. G.; Karpukhin, K. E.; Umnitsyn, A. A.

2018-02-01

The paper considers the Anti-lock Braking System (ABS) operation algorithm, which enables the implementation of hybrid braking, i.e. the braking process combining friction brake mechanisms and e-machine (electric machine), which operates in the energy recovery mode. The provided materials focus only on the rectilinear motion of the vehicle. That the ABS task consists in the maintenance of the target wheel slip ratio, which depends on the tyre-road adhesion coefficient. The tyre-road adhesion coefficient was defined based on the vehicle deceleration. In the course of calculated studies, the following operation algorithm of hybrid braking was determined. At adhesion coefficient ≤0.1, driving axle braking occurs only due to the e-machine operating in the energy recovery mode. In other cases, depending on adhesion coefficient, the e-machine provides the brake torque, which changes from 35 to 100% of the maximum available brake torque. Virtual tests showed that values of the wheel slip ratio are close to the required ones. Thus, this algorithm makes it possible to implement hybrid braking by means of the two sources creating the brake torque.

Driving Skills of Young Adults with Developmental Coordination Disorder: Regulating Speed and Coping with Distraction

ERIC Educational Resources Information Center

de Oliveira, Rita F.; Wann, John P.

2011-01-01

In two experiments, we used an automatic car simulator to examine the steering control, speed regulation and response to hazards of young adults with developmental coordination disorder (DCD) and limited driving experience. In Experiment 1 participants either used the accelerator pedal to regulate their speed, or used the brake pedal when they…

49 CFR 232.613 - End-of-train devices.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF TRANSPORTATION BRAKE SYSTEM SAFETY STANDARDS FOR FREIGHT AND OTHER NON-PASSENGER TRAINS AND EQUIPMENT; END-OF-TRAIN DEVICES Electronically Controlled Pneumatic (ECP) Braking Systems § 232.613 End-of... equipped with an ECP brake system unless that train is equipped with a functioning ECP-EOT device designed...

Modified hydraulic braking system limits angular deceleration to safe values

NASA Technical Reports Server (NTRS)

Briggs, R. S.; Council, M.; Green, P. M.

1966-01-01

Conventional spring actuated, hydraulically released, fail-safe disk braking system is modified to control the angular deceleration of a massive antenna. The hydraulic system provides an immediate preset pressure to the spring-loaded brake shoes and holds it at this value to decelerate the antenna at the desired rate.

78 FR 9623 - Federal Motor Vehicle Safety Standards; Air Brake Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-11

... [Docket No. NHTSA-2013-0011] RIN 2127-AL11 Federal Motor Vehicle Safety Standards; Air Brake Systems... rule that amended the Federal motor vehicle safety standard for air brake systems by requiring... published a final rule in the Federal Register amending Federal Motor Vehicle Safety Standard (FMVSS) No...

Antilock Braking Systems: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, the NHTSA Facts: Summer 1996, defines antilock braking systems, and discusses their benefits, how they work, and their major components. It also details how one would get used to antilock brakes, discussing how they feel and operate ...

Four-wheel dual braking for automobiles

NASA Technical Reports Server (NTRS)

Edwards, H. B.

1981-01-01

Each master cylinder applies braking power to all four wheels unlike conventional systems where cylinder operates only two wheels. If one master system fails because of fluid loss, other stops car by braking all four wheels although at half force.

Anti-lock brake system: an assessment of training on driver effectiveness.

PubMed

Mollenhauer, M A; Dingus, T A; Carney, C; Hankey, J M; Jahns, S

1997-01-01

When activated correctly, Anti-Lock Brake Systems (ABS) can provide drivers with the ability to stop a vehicle in shorter distances and allow for more vehicle control under heavy braking than conventional brake systems. This is especially true under wet or icy road conditions. However, it is believed that many drivers are either unaware of the correct method of activation or they revert back to the old method of pumping the brakes when they are faced with a hard braking situation. This paper examines the effectiveness of implementing low-cost training methods for alerting drivers to the correct brake activation technique. A 4-page, color training pamphlet was developed and subjects were given a short period of time to read it over before being asked to drive on an icy test track. Results indicated that those subjects who received the training were able to stop in shorter distances in a straight line braking event and more often used the correct brake activation technique than those subjects who did not receive the training. However, the stopping distance benefits were not realized in the curved and surprise braking events. These results suggest that the transfer of verbal knowledge may have value as a means for solving the apparent problem of improper ABS usage. However, some additional research should be done to validate these results. Since this experiment was conducted directly after the material was read, the possibility exists that without reinforcement, the trained braking techniques might become extinct in a short period of time.

Combined braking system for hybrid vehicle

NASA Astrophysics Data System (ADS)

Kulekina, A. V.; Bakholdin, P. A.; Shchurov, N. I.

2017-10-01

The paper presents an analysis of surface vehicle’s existing braking systems. The technical solution and brake-system design were developed for use of regenerative braking energy. A technical parameters comparison of energy storage devices of various types was made. Based on the comparative analysis, it was decided to use supercapacitor because of its applicability for an electric drive intermittent operation. The calculation methods of retarder key components were proposed. Therefrom, it was made a conclusion that rebuild gasoline-electric vehicles are more efficient than gasoline ones.

76 FR 8919 - Airworthiness Directives; DASSAULT AVIATION Model MYSTERE-FALCON 50 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-16

... of the emergency brake system 2 located near the nose landing gear bearing were swapped. The swapping of these two pipes implies that when the Left Hand (LH) brake pedal is depressed, the Right Hand (RH) brake unit is activated, and conversely, when the RH brake pedal is depressed, the LH brake unit is...

76 FR 27880 - Airworthiness Directives; DASSAULT AVIATION Model MYSTERE-FALCON 50 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-13

... pipes of the emergency brake system 2 located near the nose landing gear bearing were swapped. The swapping of these two pipes implies that when the Left Hand (LH) brake pedal is depressed, the Right Hand (RH) brake unit is activated, and conversely, when the RH brake pedal is depressed, the LH brake unit...

Evaluation of a sudden brake warning system: effect on the response time of the following driver.

PubMed

Isler, Robert B; Starkey, Nicola J

2010-07-01

This study used a video-based braking simulation dual task to carry out a preliminary evaluation of the effect of a sudden brake warning system (SBWS) in a leading passenger vehicle on the response time of the following driver. The primary task required the participants (N=25, 16 females, full NZ license holders) to respond to sudden braking manoeuvres of a lead vehicle during day and night driving, wet and dry conditions and in rural and urban traffic, while concurrently performing a secondary tracking task using a computer mouse. The SBWS in the lead vehicle consisted of g-force controlled activation of the rear hazard lights (the rear indicators flashed), in addition to the standard brake lights. Overall, the results revealed that responses to the braking manoeuvres of the leading vehicles when the hazard lights were activated by the warning system were 0.34 s (19%) faster compared to the standard brake lights. The SBWS was particularly effective when the simulated braking scenario of the leading vehicle did not require an immediate and abrupt braking response. Given this, the SBWS may also be beneficial for allowing smoother deceleration, thus reducing fuel consumption. These preliminary findings justify a larger, more ecologically valid laboratory evaluation which may lead to a naturalistic study in order to test this new technology in 'real world' braking situations. Copyright 2009 Elsevier Ltd. All rights reserved.

Dynamics of aircraft antiskid braking systems. [conducted at the Langley aircraft landing loads and traction facility

NASA Technical Reports Server (NTRS)

Tanner, J. A.; Stubbs, S. M.; Dreher, R. C.; Smith, E. G.

1982-01-01

A computer study was performed to assess the accuracy of three brake pressure-torque mathematical models. The investigation utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC-9 series 10 airplane. The investigation indicates that the performance of aircraft antiskid braking systems is strongly influenced by tire characteristics, dynamic response of the antiskid control valve, and pressure-torque response of the brake. The computer study employed an average torque error criterion to assess the accuracy of the models. The results indicate that a variable nonlinear spring with hysteresis memory function models the pressure-torque response of the brake more accurately than currently used models.

Compressed gas system operates semitrailer brakes during winching operation

NASA Technical Reports Server (NTRS)

Tupper, W. E.

1964-01-01

To move van-type semi-trailers into and out of confined spaces, an auxiliary braking system is mounted on a standard dolly converter. Compressed nitrogen is used to actuate the brakes which are used in conjunction with a power winch.

RaPToRS Sample Delivery System

NASA Astrophysics Data System (ADS)

Henchen, Robert; Shibata, Kye; Krieger, Michael; Pogozelski, Edward; Padalino, Stephen; Glebov, Vladimir; Sangster, Craig

2010-11-01

At various labs (NIF, LLE, NRL), activated material samples are used to measure reaction properties. The Rapid Pneumatic Transport of Radioactive Samples (RaPToRS) system quickly and safely moves these radioactive samples through a closed PVC tube via airflow. The carrier travels from the reaction chamber to the control and analysis station, pneumatically braking at the outlet. A reversible multiplexer routes samples from various locations near the shot chamber to the analysis station. Also, the multiplexer allows users to remotely load unactivated samples without manually approaching the reaction chamber. All elements of the system (pneumatic drivers, flow control valves, optical position sensors, multiplexers, Geiger counters, and release gates at the analysis station) can be controlled manually or automatically using a custom LabVIEW interface. A prototype is currently operating at NRL in Washington DC. Prospective facilities for Raptors systems include LLE and NIF.

Method and apparatus for electromagnetically braking a motor

NASA Technical Reports Server (NTRS)

Davis, Donald R. (Inventor); Radford, Nicolaus A (Inventor); Permenter, Frank Noble (Inventor); Parsons, Adam H (Inventor); Mehling, Joshua S (Inventor)

2011-01-01

An electromagnetic braking system and method is provided for selectively braking a motor using an electromagnetic brake having an electromagnet, a permanent magnet, a rotor assembly, and a brake pad. The brake assembly applies when the electromagnet is de-energized and releases when the electromagnet is energized. When applied the permanent magnet moves the brake pad into frictional engagement with a housing, and when released the electromagnet cancels the flux of the permanent magnet to allow a leaf spring to move the brake pad away from the housing. A controller has a DC/DC converter for converting a main bus voltage to a lower braking voltage based on certain parameters. The converter utilizes pulse-width modulation (PWM) to regulate the braking voltage. A calibrated gap is defined between the brake pad and permanent magnet when the brake assembly is released, and may be dynamically modified via the controller.

A simulation study of the effects of alcohol on driving performance in a Chinese population.

PubMed

Li, Y C; Sze, N N; Wong, S C; Yan, Wei; Tsui, K L; So, F L

2016-10-01

Driving under the influence of alcohol (DUIA) is a significant factor contributing to road traffic crashes, injuries, and fatalities. Although the effects of alcohol on driving performance are widely acknowledged, studies of the effects of alcohol impairment on driving performance and particularly on the control system of Chinese adults are rare. This study attempts to evaluate the effects of alcohol on the driving performance of Chinese adults using a driving simulator. A double-blind experimental study was conducted to evaluate the effects of alcohol impairment on the driving performance of 52 Chinese participants using a driving simulator. A series of simulated driving tests covering two driving modules, including emergency braking (EB) and following braking (FB), at 50km/h and 80km/h were performed. Linear mixed models were established to evaluate driving performance in terms of braking reaction time (BRT), the standard deviation of lateral position (SD-LANE), and the standard deviation of speed (SD-SPEED). Driving performance in terms of BRT and SD-LANE was highly correlated with the level of alcohol consumption, with a one-unit increase in breath alcohol concentration (BrAC) degrading BRT and SD-LANE by 0.3% and 0.2%, respectively. Frequent drinkers generally reacted faster in their BRT than less-frequent drinkers and non-drinkers by 10.2% and 30.6%, respectively. Moreover, alcohol impairment had varying effects on certain aspects of the human control system, and automatic action was less likely to be affected than voluntary action from a psychological viewpoint. The findings should be useful for planning and developing effective measures to combat drink driving in Chinese communities. Copyright © 2016 Elsevier Ltd. All rights reserved.

Performance of a Rotary Wing Air Brake in Supersonic Flow

DTIC Science & Technology

1947-05-18

a pneumatic thrust measuring system (3) Strobotac and Audio Signal Generator for RPM measurements, (4) motion picture cameras and miscellaneous...produced by the head to keep the brake engaged. The " pneumatic thrust measuring system1* utilised the bellows described above to oppose the drag force...a brake , to prevent its rotation when desired. To release the brake it was necessary to inflate the internal thrust bellows, thereby disengaging

49 CFR 571.122a - Standard No. 122; Motorcycle brake systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... application. Skid number means the frictional resistance of a pavement measured in accordance with ASTM E274... brake system consisting of two or more subsystems actuated by a single control designed so that a...), but not less than 0 Newtons (0 pounds). S5.8Service brake system design durability. Each motorcycle...

49 CFR 571.122a - Standard No. 122; Motorcycle brake systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... application. Skid number means the frictional resistance of a pavement measured in accordance with ASTM E274... brake system consisting of two or more subsystems actuated by a single control designed so that a...), but not less than 0 Newtons (0 pounds). S5.8Service brake system design durability. Each motorcycle...

49 CFR 393.55 - Antilock brake systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 57396, Sept. 21, 2010. (a) Hydraulic brake systems. Each truck and bus manufactured on or after March 1, 1999 (except trucks and buses engaged in driveaway-towaway operations), and equipped with a hydraulic... FMVSS No. 105 (49 CFR 571.105, S5.3). (c) Air brake systems. (1) Each truck tractor manufactured on or...

76 FR 44829 - Federal Motor Vehicle Safety Standards; Air Brake Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-27

... [Docket No. NHTSA-2009-0175] RIN 2127-AK84 Federal Motor Vehicle Safety Standards; Air Brake Systems... final rule that amended the Federal motor vehicle safety standard for air brake systems by requiring... July 27, 2009, NHTSA published a final rule in the Federal Register amending Federal Motor Vehicle...

Development of remote data acquisition system based on OPC for brake test bench

NASA Astrophysics Data System (ADS)

Wang, Yiwei; Wu, Mengling; Tian, Chun; Ma, Tianhe

2017-08-01

The 1:1 train brake system test bench can be used to carry out brake-related adhesion-slid control, stability test, noise test and dynamic test. To collect data of the test bench, a data acquisition method is needed. In this paper, the remote data acquisition system of test bench is built by LabVIEW based on OPC technology. Unlike the traditional hardwire way connecting PLC acquisition module with sensors, the novel method is used to collect data and share them through the internal LAN built by Ethernet switches, which avoids the complex wiring interference in an easy, efficient and flexible way. The system has been successfully applied to the data acquisition activities of the comprehensive brake system test bench of CRRC Nanjing Puzhen Haitai Brake Equipment Co., Ltd., and the relationship test between the adhesion coefficient and the slip-ratio is realized. The speed signal, torque signal and brake disc temperature can be collected and displayed. The results show that the system is reliable, convenient, and efficient, and can meet the requirements of data acquisition.

75 FR 22710 - Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146-100A and -200A Series...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-30

... aerodynamic braking and to dump lift to ensure that the wheel brakes can provide the necessary speed reduction... the wheel brakes can provide the necessary speed reduction. A review of the changing operational... on landing to provide aerodynamic braking and to dump lift to ensure that the wheel brakes can...

EEG-Based Detection of Braking Intention Under Different Car Driving Conditions

PubMed Central

Hernández, Luis G.; Mozos, Oscar Martinez; Ferrández, José M.; Antelis, Javier M.

2018-01-01

The anticipatory recognition of braking is essential to prevent traffic accidents. For instance, driving assistance systems can be useful to properly respond to emergency braking situations. Moreover, the response time to emergency braking situations can be affected and even increased by different driver's cognitive states caused by stress, fatigue, and extra workload. This work investigates the detection of emergency braking from driver's electroencephalographic (EEG) signals that precede the brake pedal actuation. Bioelectrical signals were recorded while participants were driving in a car simulator while avoiding potential collisions by performing emergency braking. In addition, participants were subjected to stress, workload, and fatigue. EEG signals were classified using support vector machines (SVM) and convolutional neural networks (CNN) in order to discriminate between braking intention and normal driving. Results showed significant recognition of emergency braking intention which was on average 71.1% for SVM and 71.8% CNN. In addition, the classification accuracy for the best participant was 80.1 and 88.1% for SVM and CNN, respectively. These results show the feasibility of incorporating recognizable driver's bioelectrical responses into advanced driver-assistance systems to carry out early detection of emergency braking situations which could be useful to reduce car accidents. PMID:29910722

Wheel slide protection control using a command map and Smith predictor for the pneumatic brake system of a railway vehicle

NASA Astrophysics Data System (ADS)

Lee, Nam-Jin; Kang, Chul-Goo

2016-10-01

In railway vehicles, excessive sliding or wheel locking can occur while braking because of a temporarily degraded adhesion between the wheel and the rail caused by the contaminated or wet surface of the rail. It can damage the wheel tread and affect the performance of the brake system and the safety of the railway vehicle. To safeguard the wheelset from these phenomena, almost all railway vehicles are equipped with wheel slide protection (WSP) systems. In this study, a new WSP algorithm is proposed. The features of the proposed algorithm are the use of the target sliding speed, the determination of a command for WSP valves using command maps, and compensation for the time delay in pneumatic brake systems using the Smith predictor. The proposed WSP algorithm was verified using experiments with a hardware-in-the-loop simulation system including the hardware of the pneumatic brake system.

Intelligent Tires Based on Measurement of Tire Deformation

NASA Astrophysics Data System (ADS)

Matsuzaki, Ryosuke; Todoroki, Akira

From a traffic safety point-of-view, there is an urgent need for intelligent tires as a warning system for road conditions, for optimized braking control on poor road surfaces and as a tire fault detection system. Intelligent tires, equipped with sensors for monitoring applied strain, are effective in improving reliability and control systems such as anti-lock braking systems (ABSs). In previous studies, we developed a direct tire deformation or strain measurement system with sufficiently low stiffness and high elongation for practical use, and a wireless communication system between tires and vehicle that operates without a battery. The present study investigates the application of strain data for an optimized braking control and road condition warning system. The relationships between strain sensor outputs and tire mechanical parameters, including braking torque, effective radius and contact patch length, are calculated using finite element analysis. Finally, we suggested the possibility of optimized braking control and road condition warning systems. Optimized braking control can be achieved by keeping the slip ratio constant. The road condition warning would be actuated if the recorded friction coefficient at a certain slip ratio is lower than a ‘safe’ reference value.

Intelligent tires for improved tire safety using wireless strain measurement

NASA Astrophysics Data System (ADS)

Matsuzaki, Ryosuke; Todoroki, Akira

2008-03-01

From a traffic safety point-of-view, there is an urgent need for intelligent tires as a warning system for road conditions, for optimized braking control on poor road surfaces and as a tire fault detection system. Intelligent tires, equipped with sensors for monitoring applied strain, are effective in improving reliability and control systems such as anti-lock braking systems (ABSs). In previous studies, we developed a direct tire deformation or strain measurement system with sufficiently low stiffness and high elongation for practical use, and a wireless communication system between tires and vehicle that operates without a battery. The present study investigates the application of strain data for an optimized braking control and road condition warning system. The relationships between strain sensor outputs and tire mechanical parameters, including braking torque, effective radius and contact patch length, are calculated using finite element analysis. Finally, we suggested the possibility of optimized braking control and road condition warning systems. Optimized braking control can be achieved by keeping the slip ratio constant. The road condition warning would be actuated if the recorded friction coefficient at a certain slip ratio is lower than a 'safe' reference value.

The antilock braking system anomaly: a drinking driver problem?

PubMed

Harless, David W; Hoffer, George E

2002-05-01

Antilock braking systems (ABS) have held promise for reducing the incidence of accidents because they reduce stopping times on slippery surfaces and allow drivers to maintain steering control during emergency braking. Farmer et al. (Accident Anal. Prevent. 29 (1997) 745) provide evidence that antilock brakes are beneficial to nonoccupants: a set of 1992 model General Motors vehicles equipped with antilock brakes were involved in significantly fewer fatal crashes in which occupants of other vehicles, pedestrians, or bicyclists were killed. But, perversely, the risk of death for occupants of vehicles equipped with antilock brakes increased significantly after adoption. Farmer (Accident Anal. Prevent. 33 (2001) 361) updates the analysis for 1996- 1998 and finds a significant attenuation in the ABS anomaly. Researchers have put forward two hypotheses to explain this antilock brake anomaly: risk compensation and improper operation of antilock brake-equipped vehicles. We provide strong evidence for the improper operation hypothesis by showing that the antilock brake anomaly is confined largely to drinking drivers. Further, we show that the attenuation phenomenon occurs consistently after the first three to four years of vehicle service.

An integrated control strategy for the composite braking system of an electric vehicle with independently driven axles

NASA Astrophysics Data System (ADS)

Sun, Fengchun; Liu, Wei; He, Hongwen; Guo, Hongqiang

2016-08-01

For an electric vehicle with independently driven axles, an integrated braking control strategy was proposed to coordinate the regenerative braking and the hydraulic braking. The integrated strategy includes three modes, namely the hybrid composite mode, the parallel composite mode and the pure hydraulic mode. For the hybrid composite mode and the parallel composite mode, the coefficients of distributing the braking force between the hydraulic braking and the two motors' regenerative braking were optimised offline, and the response surfaces related to the driving state parameters were established. Meanwhile, the six-sigma method was applied to deal with the uncertainty problems for reliability. Additionally, the pure hydraulic mode is activated to ensure the braking safety and stability when the predictive failure of the response surfaces occurs. Experimental results under given braking conditions showed that the braking requirements could be well met with high braking stability and energy regeneration rate, and the reliability of the braking strategy was guaranteed on general braking conditions.

Prediction Study on Anti-Slide Control of Railway Vehicle Based on RBF Neural Networks

NASA Astrophysics Data System (ADS)

Yang, Lijun; Zhang, Jimin

While railway vehicle braking, Anti-slide control system will detect operating status of each wheel-sets e.g. speed difference and deceleration etc. Once the detected value on some wheel-set is over pre-defined threshold, brake effort on such wheel-set will be adjusted automatically to avoid blocking. Such method takes effect on guarantee safety operation of vehicle and avoid wheel-set flatness, however it cannot adapt itself to the rail adhesion variation. While wheel-sets slide, the operating status is chaotic time series with certain law, and can be predicted with the law and experiment data in certain time. The predicted values can be used as the input reference signals of vehicle anti-slide control system, to judge and control the slide status of wheel-sets. In this article, the RBF neural networks is taken to predict wheel-set slide status in multi-step with weight vector adjusted based on online self-adaptive algorithm, and the center & normalizing parameters of active function of the hidden unit of RBF neural networks' hidden layer computed with K-means clustering algorithm. With multi-step prediction simulation, the predicted signal with appropriate precision can be used by anti-slide system to trace actively and adjust wheel-set slide tendency, so as to adapt to wheel-rail adhesion variation and reduce the risk of wheel-set blocking.

Use of MSC/NASTRAN for the thermal analysis of the Space Shuttle Orbiter braking system

NASA Technical Reports Server (NTRS)

Shu, James; Mccann, David

1987-01-01

A description is given of the thermal modeling and analysis effort being conducted to investigate the transient temperature and thermal stress characteristics of the Space Shuttle Orbiter brake components and subsystems. Models are constructed of the brake stator as well as of the entire brake assembly to analyze the temperature distribution and thermal stress during the landing and braking process. These investigations are carried out on a UNIVAC computer system with MSC/NASTRAN Version 63. Analytical results and solution methods are presented and comparisons are made with SINDA results.

Review of NASA antiskid braking research

NASA Technical Reports Server (NTRS)

Tanner, J. A.

1982-01-01

NASA antiskid braking system research programs are reviewed. These programs include experimental studies of four antiskid systems on the Langley Landing Loads Track, flights tests with a DC-9 airplane, and computer simulation studies. Results from these research efforts include identification of factors contributing to degraded antiskid performance under adverse weather conditions, tire tread temperature measurements during antiskid braking on dry runway surfaces, and an assessment of the accuracy of various brake pressure-torque computer models. This information should lead to the development of better antiskid systems in the future.

Development of Anti-lock Braking System (ABS) for Vehicles Braking

NASA Astrophysics Data System (ADS)

Minh, Vu Trieu; Oamen, Godwin; Vassiljeva, Kristina; Teder, Leo

2016-11-01

This paper develops a real laboratory of anti-lock braking system (ABS) for vehicle and conducts real experiments to verify the ability of this ABS to prevent the vehicle wheel from being locked while braking. Two controllers of PID and fuzzy logic are tested for analysis and comparison. This ABS laboratory is designed for bachelor and master students to simulate and analyze performances of ABS with different control techniques on various roads and load conditions. This paper provides educational theories and practices on the design of control for system dynamics.

49 CFR 232.603 - Design, interoperability, and configuration management requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... requirements. (a) General. A freight car or freight train equipped with an ECP brake system shall, at a minimum...) Approval. A freight train or freight car equipped with an ECP brake system and equipment covered by the AAR...) Configuration management. A railroad operating a freight train or freight car equipped with ECP brake systems...

49 CFR 232.603 - Design, interoperability, and configuration management requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... requirements. (a) General. A freight car or freight train equipped with an ECP brake system shall, at a minimum...) Approval. A freight train or freight car equipped with an ECP brake system and equipment covered by the AAR...) Configuration management. A railroad operating a freight train or freight car equipped with ECP brake systems...

49 CFR 232.603 - Design, interoperability, and configuration management requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... requirements. (a) General. A freight car or freight train equipped with an ECP brake system shall, at a minimum...) Approval. A freight train or freight car equipped with an ECP brake system and equipment covered by the AAR...) Configuration management. A railroad operating a freight train or freight car equipped with ECP brake systems...

49 CFR 232.603 - Design, interoperability, and configuration management requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... requirements. (a) General. A freight car or freight train equipped with an ECP brake system shall, at a minimum...) Approval. A freight train or freight car equipped with an ECP brake system and equipment covered by the AAR...) Configuration management. A railroad operating a freight train or freight car equipped with ECP brake systems...

Aircraft Rollout Iterative Energy Simulation

NASA Technical Reports Server (NTRS)

Kinoshita, L.

1986-01-01

Aircraft Rollout Iterative Energy Simulation (ARIES) program analyzes aircraft-brake performance during rollout. Simulates threedegree-of-freedom rollout after nose-gear touchdown. Amount of brake energy dissipated during aircraft landing determines life expectancy of brake pads. ARIES incorporates brake pressure, actual flight data, crosswinds, and runway characteristics to calculate following: brake energy during rollout for up to four independent brake systems; time profiles of rollout distance, velocity, deceleration, and lateral runway position; and all aerodynamic moments on aircraft. ARIES written in FORTRAN 77 for batch execution.

Dynamics of Braking Vehicles: From Coulomb Friction to Anti-Lock Braking Systems

ERIC Educational Resources Information Center

Tavares, J. M.

2009-01-01

The dynamics of braking of wheeled vehicles is studied using the Coulomb approximation for the friction between road and wheels. The dependence of the stopping distance on the mass of the vehicle, on the number of its wheels and on the intensity of the braking torque is established. It is shown that there are two regimes of braking, with and…

49 CFR 393.5 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... processing plant or storage location, as evidenced by skeletal construction that accommodates harvest... mechanism used to stop, or hold a vehicle stationary. Brake power assist unit. A device installed in a... force on the service brake control. Brake power unit. A device installed in a brake system that provides...

49 CFR 393.5 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... processing plant or storage location, as evidenced by skeletal construction that accommodates harvest... mechanism used to stop, or hold a vehicle stationary. Brake power assist unit. A device installed in a... force on the service brake control. Brake power unit. A device installed in a brake system that provides...

49 CFR 383.95 - Restrictions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the skills test and the restriction, air brakes shall include any braking system operating fully or...; REQUIREMENTS AND PENALTIES Vehicle Groups and Endorsements § 383.95 Restrictions. (a) Air brake restrictions... skills test in a vehicle not equipped with air brakes, the State must indicate on the CDL, if issued...

Energy recapture through deceleration - regenerative braking in electric vehicles from a user perspective.

PubMed

Cocron, Peter; Bühler, Franziska; Franke, Thomas; Neumann, Isabel; Dielmann, Benno; Krems, Josef F

2013-01-01

We report results from a 1-year field study (N = 80) on user interactions with regenerative braking in electric vehicles. Designed to recapture energy in vehicles with electric powertrains, regenerative braking has an important influence on both the task of driving and energy consumption. Results from user assessments and data from onboard data loggers indicate that most drivers quickly learned to interact with the system, which was triggered via accelerator. Further, conventional braking manoeuvres decreased significantly as the majority of deceleration episodes could only be executed through regenerative braking. Still, some drivers reported difficulties when adapting to the system. These difficulties could be addressed by offering different levels of regeneration so that the intensity of the deceleration could be individually modified. In general, the system is trusted and regarded as a valuable tool for prolonging range. Regenerative braking in electric vehicles has direct implications for the driving task. We found that drivers quickly learn to use and accept a system, which is triggered via accelerator. For those reporting difficulties in the interaction, it appears reasonable to integrate options to customise or switch off the system.

78 FR 25347 - Petition for Waiver of Compliance

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-30

.... Specifically, BNSF and UP seek a waiver of compliance from 49 CFR 232.305(b)(2) for railroad cars tested with automatic single car test devices (ASCTD). The current rule stipulates that if a car is on a shop or repair track for any reason and has not had a single car air brake test within the previous 12-month period, a...

Potential Occupant Injury Reduction in Pre-Crash System Equipped Vehicles in the Striking Vehicle of Rear-end Crashes.

PubMed

Kusano, Kristofer D; Gabler, Hampton C

2010-01-01

To mitigate the severity of rear-end and other collisions, Pre-Crash Systems (PCS) are being developed. These active safety systems utilize radar and/or video cameras to determine when a frontal crash, such as a front-to-back rear-end collisions, is imminent and can brake autonomously, even with no driver input. Of these PCS features, the effects of autonomous pre-crash braking are estimated. To estimate the maximum potential for injury reduction due to autonomous pre-crash braking in the striking vehicle of rear-end crashes, a methodology is presented for determining 1) the reduction in vehicle crash change in velocity (ΔV) due to PCS braking and 2) the number of injuries that could be prevented due to the reduction in collision severity. Injury reduction was only performed for belted drivers, as unbelted drivers have an unknown risk of being thrown out of position. The study was based on 1,406 rear-end striking vehicles from NASS / CDS years 1993 to 2008. PCS parameters were selected from realistic values and varied to examine the effect on system performance. PCS braking authority was varied from 0.5 G's to 0.8 G's while time to collision (TTC) was held at 0.45 seconds. TTC was then varied from 0.3 second to 0.6 seconds while braking authority was held constant at 0.6 G's. A constant braking pulse (step function) and ramp-up braking pulse were used. The study found that automated PCS braking could reduce the crash ΔV in rear-end striking vehicles by an average of 12% - 50% and avoid 0% - 14% of collisions, depending on PCS parameters. Autonomous PCS braking could potentially reduce the number of injured drivers who are belted by 19% to 57%.

Method for controlling a motor vehicle powertrain

DOEpatents

Burba, Joseph C.; Landman, Ronald G.; Patil, Prabhakar B.; Reitz, Graydon A.

1990-01-01

A multiple forward speed automatic transmission produces its lowest forward speed ratio when a hydraulic clutch and hydraulic brake are disengaged and a one-way clutch connects a ring gear to the transmission casing. Second forward speed ratio results when the hydraulic clutch is engaged to connect the ring gear to the planetary carrier of a second gear set. Reverse drive and regenerative operation result when an hydraulic brake fixes the planetary and the direction of power flow is reversed. Various sensors produce signals representing the position of the gear selector lever operated manually by the vehicle operator, the speed of the power source, the state of the ignition key, and the rate of release of an accelerator pedal. A control algorithm produces input data representing a commanded upshift, a commanded downshift and a torque command and various constant torque signals. A microprocessor processes the input and produces a response to them in accordance with the execution of a control algorithm. Output or response signals cause selective engagement and disengagement of the clutch and brake to produce the forward drive, reverse and regenerative operation of the transmission.

Method for controlling a motor vehicle powertrain

DOEpatents

Burba, J.C.; Landman, R.G.; Patil, P.B.; Reitz, G.A.

1990-05-22

A multiple forward speed automatic transmission produces its lowest forward speed ratio when a hydraulic clutch and hydraulic brake are disengaged and a one-way clutch connects a ring gear to the transmission casing. Second forward speed ratio results when the hydraulic clutch is engaged to connect the ring gear to the planetary carrier of a second gear set. Reverse drive and regenerative operation result when an hydraulic brake fixes the planetary and the direction of power flow is reversed. Various sensors produce signals representing the position of the gear selector lever operated manually by the vehicle operator, the speed of the power source, the state of the ignition key, and the rate of release of an accelerator pedal. A control algorithm produces input data representing a commanded upshift, a commanded downshift and a torque command and various constant torque signals. A microprocessor processes the input and produces a response to them in accordance with the execution of a control algorithm. Output or response signals cause selective engagement and disengagement of the clutch and brake to produce the forward drive, reverse and regenerative operation of the transmission. 7 figs.

30 CFR 56.14101 - Brakes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... mobile equipment shall be equipped with a service brake system capable of stopping and holding the... which is not originally equipped with brakes unless the manner in which the equipment is being operated requires the use of brakes for safe operation. This standard does not apply to rail equipment. (2) If...

30 CFR 57.14101 - Brakes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... mobile equipment shall be equipped with a service brake system capable of stopping and holding the... which is not originally equipped with brakes unless the manner in which the equipment is being operated requires the use of brakes for safe operation. This standard does not apply to rail equipment. (2) If...

16 CFR 1512.5 - Requirements for braking system.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the braking force transmitted to the rear wheel shall be in accordance with the sidewalk bicycle.... Bicycles shall be equipped with front- and rear-wheel brakes or rear-wheel brakes only. (b) Handbrakes. Handbrakes shall be tested at least ten times by applying a force sufficient to cause the handlever to...

16 CFR 1512.5 - Requirements for braking system.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the braking force transmitted to the rear wheel shall be in accordance with the sidewalk bicycle.... Bicycles shall be equipped with front- and rear-wheel brakes or rear-wheel brakes only. (b) Handbrakes. Handbrakes shall be tested at least ten times by applying a force sufficient to cause the handlever to...

16 CFR 1512.5 - Requirements for braking system.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the braking force transmitted to the rear wheel shall be in accordance with the sidewalk bicycle.... Bicycles shall be equipped with front- and rear-wheel brakes or rear-wheel brakes only. (b) Handbrakes. Handbrakes shall be tested at least ten times by applying a force sufficient to cause the handlever to...

16 CFR 1512.5 - Requirements for braking system.

Code of Federal Regulations, 2010 CFR

2010-01-01

... the braking force transmitted to the rear wheel shall be in accordance with the sidewalk bicycle.... Bicycles shall be equipped with front- and rear-wheel brakes or rear-wheel brakes only. (b) Handbrakes. Handbrakes shall be tested at least ten times by applying a force sufficient to cause the handlever to...

49 CFR 232.103 - General requirements for all train brake systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the air compressor governor starting or loading pressure. (l) Except as otherwise provided in this... brake pipe air pressure: Road Service 90 Switch Service 60 (2) Minimum differential between brake pipe and main reservoir air pressures, with brake valve in running position 15 (3) Safety valve for...

49 CFR 232.103 - General requirements for all train brake systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the air compressor governor starting or loading pressure. (l) Except as otherwise provided in this... brake pipe air pressure: Road Service 90 Switch Service 60 (2) Minimum differential between brake pipe and main reservoir air pressures, with brake valve in running position 15 (3) Safety valve for...

49 CFR 571.122 - Standard No. 122; Motorcycle brake systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... mile before any brake application. Skid number means the frictional resistance of a pavement measured... control designed so that a leakage-type failure of a pressure component in a single subsystem (except... pounds). S5.8Service brake system design durability. Each motorcycle shall be capable of completing all...

75 FR 55628 - National Highway Traffic Safety Administration Reports, Forms and Record Keeping Requirements...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-13

... vehicle brake fluid or hydraulic system mineral oil is permanently attached, clearly states the contents... motor vehicle brake fluid and hydraulic mineral oil containers as specified in FMVSS No. 116, Motor..., specifies performance and design requirements for motor vehicle brake fluids and hydraulic system mineral...

Laboratory testing of airborne brake wear particle emissions using a dynamometer system under urban city driving cycles

NASA Astrophysics Data System (ADS)

Hagino, Hiroyuki; Oyama, Motoaki; Sasaki, Sousuke

2016-04-01

To measure driving-distance-based mass emission factors for airborne brake wear particulate matter (PM; i.e., brake wear particles) related to the non-asbestos organic friction of brake assembly materials (pads and lining), and to characterize the components of brake wear particles, a brake wear dynamometer with a constant-volume sampling system was developed. Only a limited number of studies have investigated brake emissions under urban city driving cycles that correspond to the tailpipe emission test (i.e., JC08 or JE05 mode of Japanese tailpipe emission test cycles). The tests were performed using two passenger cars and one middle-class truck. The observed airborne brake wear particle emissions ranged from 0.04 to 1.4 mg/km/vehicle for PM10 (particles up to 10 μm (in size), and from 0.04 to 1.2 mg/km/vehicle for PM2.5. The proportion of brake wear debris emitted as airborne brake wear particles was 2-21% of the mass of wear. Oxygenated carbonaceous components were included in the airborne PM but not in the original friction material, which indicates that changes in carbon composition occurred during the abrasion process. Furthermore, this study identified the key tracers of brake wear particles (e.g., Fe, Cu, Ba, and Sb) at emission levels comparable to traffic-related atmospheric environments.

NHTSA light vehicle antilock brake systems research program task 5, part 1 : examination of drivers' collision avoidance behavior using conventional and antilock brake systems on the Iowa driving simulator

DOT National Transportation Integrated Search

2000-08-01

The National Highway Traffic Safety Administration (NHTSA) has developed its Light Vehicle Antilock Brake Systems (ABS) Research Program in an effort to determine the cause(s) of the apparent increase in single-vehicle run-off-road crashes and decrea...

The Application of Vibration Accelerations in the Assessment of Average Friction Coefficient of a Railway Brake Disc

NASA Astrophysics Data System (ADS)

Sawczuk, Wojciech

2017-06-01

Due to their wide range of friction characteristics resulting from the application of different friction materials and good heat dissipation conditions, railway disc brakes have long replaced block brakes in many rail vehicles. A block brake still remains in use, however, in low speed cargo trains. The paper presents the assessment of the braking process through the analysis of vibrations generated by the components of the brake system during braking. It presents a possibility of a wider application of vibroacoustic diagnostics (VA), which aside from the assessment of technical conditions (wear of brake pads) also enables the determination of the changes of the average friction coefficient as a function of the braking onset speed. Vibration signals of XYZ were measured and analyzed. The analysis of the results has shown that there is a relation between the values of the point measures and the wear of the brake pads.

Detection of visually unrecognizable braking tracks using Laser-Induced Breakdown Spectroscopy, a feasibility study

NASA Astrophysics Data System (ADS)

Prochazka, David; Bilík, Martin; Prochazková, Petra; Brada, Michal; Klus, Jakub; Pořízka, Pavel; Novotný, Jan; Novotný, Karel; Ticová, Barbora; Bradáč, Albert; Semela, Marek; Kaiser, Jozef

2016-04-01

Identification of the position, length and mainly beginning of a braking track has proven to be essential for determination of causes of a road traffic accident. With the introduction of modern safety braking systems and assistance systems such as the Anti-lock Braking System (ABS) or Electronic Stability Control (ESC), the visual identification of braking tracks that has been used up until the present is proving to be rather complicated or even impossible. This paper focuses on identification of braking tracks using a spectrochemical analysis of the road surface. Laser-Induced Breakdown Spectroscopy (LIBS) was selected as a method suitable for fast in-situ element detection. In the course of detailed observations of braking tracks it was determined that they consist of small particles of tire treads that are caught in intrusions in the road surface. As regards detection of the "dust" resulting from wear and tear of tire treads in the environment, organic zinc was selected as the identification element in the past. The content of zinc in tire treads has been seen to differ with regard to various sources and tire types; however, the arithmetic mean and modus of these values are approximately 1% by weight. For in-situ measurements of actual braking tracks a mobile LIBS device equipped with a special module was used. Several measurements were performed for 3 different cars and tire types respectively which slowed down with full braking power. Moreover, the influence of different initial speed, vehicle mass and braking track length on detected signal is discussed here.

49 CFR 238.315 - Class IA brake test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... that utilize an electric signal to communicate a service brake application and only a pneumatic signal... and release of the brakes on the last car in the train; and (6) The communicating signal system is... be used to verify the set and release on cars so equipped. However, the observation of the brake...

49 CFR 238.315 - Class IA brake test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... that utilize an electric signal to communicate a service brake application and only a pneumatic signal... and release of the brakes on the last car in the train; and (6) The communicating signal system is... be used to verify the set and release on cars so equipped. However, the observation of the brake...

49 CFR 238.315 - Class IA brake test.

Code of Federal Regulations, 2010 CFR

2010-10-01

... that utilize an electric signal to communicate a service brake application and only a pneumatic signal... and release of the brakes on the last car in the train; and (6) The communicating signal system is... be used to verify the set and release on cars so equipped. However, the observation of the brake...

16 CFR § 1512.5 - Requirements for braking system.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the braking force transmitted to the rear wheel shall be in accordance with the sidewalk bicycle.... Bicycles shall be equipped with front- and rear-wheel brakes or rear-wheel brakes only. (b) Handbrakes. Handbrakes shall be tested at least ten times by applying a force sufficient to cause the handlever to...

49 CFR 393.51 - Warning signals, air pressure and vacuum gauges.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the vehicle's service brake system. The warning signal must meet the applicable requirements of... September 1, 1975, must meet the brake system indicator lamp requirements of FMVSS No. 571.105 (S5.3..., must have a warning signal which operates before or upon application of the brakes in the event of a...

49 CFR 571.122 - Standard No. 122; Motorcycle brake systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... mile before any brake application. Skid number means the frictional resistance of a pavement measured... subsystems actuated by a single control designed so that a leakage-type failure of a pressure component in a...), but not less than 0 Newtons (0 pounds). S5.8Service brake system design durability. Each motorcycle...

49 CFR 571.122 - Standard No. 122; Motorcycle brake systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... mile before any brake application. Skid number means the frictional resistance of a pavement measured... subsystems actuated by a single control designed so that a leakage-type failure of a pressure component in a...), but not less than 0 Newtons (0 pounds). S5.8Service brake system design durability. Each motorcycle...

Research study on antiskid braking systems for the space shuttle

NASA Technical Reports Server (NTRS)

Auselmi, J. A.; Weinberg, L. W.; Yurczyk, R. F.; Nelson, W. G.

1973-01-01

A research project to investigate antiskid braking systems for the space shuttle vehicle was conducted. System from the Concorde, Boeing 747, Boeing 737, and Lockheed L-1011 were investigated. The characteristics of the Boeing 737 system which caused it to be selected are described. Other subjects which were investigated are: (1) trade studies of brake control concepts, (2) redundancy requirements trade study, (3) laboratory evaluation of antiskid systems, and (4) space shuttle hardware criteria.

Study on real-time elevator brake failure predictive system

NASA Astrophysics Data System (ADS)

Guo, Jun; Fan, Jinwei

2013-10-01

This paper presented a real-time failure predictive system of the elevator brake. Through inspecting the running state of the coil by a high precision long range laser triangulation non-contact measurement sensor, the displacement curve of the coil is gathered without interfering the original system. By analyzing the displacement data using the diagnostic algorithm, the hidden danger of the brake system can be discovered in time and thus avoid the according accident.

Indonesian commercial bus drum brake system temperature model

NASA Astrophysics Data System (ADS)

Wibowo, D. B.; Haryanto, I.; Laksono, N. P.

2016-03-01

Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

Indonesian commercial bus drum brake system temperature model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wibowo, D. B., E-mail: rmt.bowo@gmail.com; Haryanto, I., E-mail: ismoyo2001@yahoo.de; Laksono, N. P., E-mail: priyolaksono89@gmail.com

Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle,more » ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.« less

Optical classification for quality and defect analysis of train brakes

NASA Astrophysics Data System (ADS)

Glock, Stefan; Hausmann, Stefan; Gerke, Sebastian; Warok, Alexander; Spiess, Peter; Witte, Stefan; Lohweg, Volker

2009-06-01

In this paper we present an optical measurement system approach for quality analysis of brakes which are used in high-speed trains. The brakes consist of the so called brake discs and pads. In a deceleration process the discs will be heated up to 500°C. The quality measure is based on the fact that the heated brake discs should not generate hot spots inside the brake material. Instead, the brake disc should be heated homogeneously by the deceleration. Therefore, it makes sense to analyze the number of hot spots and their relative gradients to create a quality measure for train brakes. In this contribution we present a new approach for a quality measurement system which is based on an image analysis and classification of infra-red based heat images. Brake images which are represented in pseudo-color are first transformed in a linear grayscale space by a hue-saturation-intensity (HSI) space. This transform is necessary for the following gradient analysis which is based on gray scale gradient filters. Furthermore, different features based on Haralick's measures are generated from the gray scale and gradient images. A following Fuzzy-Pattern-Classifier is used for the classification of good and bad brakes. It has to be pointed out that the classifier returns a score value for each brake which is between 0 and 100% good quality. This fact guarantees that not only good and bad bakes can be distinguished, but also their quality can be labeled. The results show that all critical thermal patterns of train brakes can be sensed and verified.

Advanced emergency braking controller design for pedestrian protection oriented automotive collision avoidance system.

PubMed

Lie, Guo; Zejian, Ren; Pingshu, Ge; Jing, Chang

2014-01-01

Automotive collision avoidance system, which aims to enhance the active safety of the vehicle, has become a hot research topic in recent years. However, most of the current systems ignore the active protection of pedestrian and other vulnerable groups in the transportation system. An advanced emergency braking control system is studied by taking into account the pedestrians and the vehicles. Three typical braking scenarios are defined and the safety situations are assessed by comparing the current distance between the host vehicle and the obstacle with the critical braking distance. To reflect the nonlinear time-varying characteristics and control effect of the longitudinal dynamics, the vehicle longitudinal dynamics model is established in CarSim. Then the braking controller with the structure of upper and lower layers is designed based on sliding mode control and the single neuron PID control when confronting deceleration or emergency braking conditions. Cosimulations utilizing CarSim and Simulink are finally carried out on a CarSim intelligent vehicle model to explore the effectiveness of the proposed controller. Results display that the designed controller has a good response in preventing colliding with the front vehicle or pedestrian.

Advanced Emergency Braking Controller Design for Pedestrian Protection Oriented Automotive Collision Avoidance System

PubMed Central

Lie, Guo; Zejian, Ren; Pingshu, Ge; Jing, Chang

2014-01-01

Automotive collision avoidance system, which aims to enhance the active safety of the vehicle, has become a hot research topic in recent years. However, most of the current systems ignore the active protection of pedestrian and other vulnerable groups in the transportation system. An advanced emergency braking control system is studied by taking into account the pedestrians and the vehicles. Three typical braking scenarios are defined and the safety situations are assessed by comparing the current distance between the host vehicle and the obstacle with the critical braking distance. To reflect the nonlinear time-varying characteristics and control effect of the longitudinal dynamics, the vehicle longitudinal dynamics model is established in CarSim. Then the braking controller with the structure of upper and lower layers is designed based on sliding mode control and the single neuron PID control when confronting deceleration or emergency braking conditions. Cosimulations utilizing CarSim and Simulink are finally carried out on a CarSim intelligent vehicle model to explore the effectiveness of the proposed controller. Results display that the designed controller has a good response in preventing colliding with the front vehicle or pedestrian. PMID:25097870

Brake testing methodology study : driver effects testing

DOT National Transportation Integrated Search

1999-03-01

The National Highway Traffic Safety Administration (NHTSA) is exploring the feasibility of developing brake tests to measure brake system performance of light vehicles. Developing test procedures requires controlling test variability so that measured...

Emergency Braking of a Mine Hoist in the Context of the Braking System Selection

NASA Astrophysics Data System (ADS)

Wolny, Stanisław

2017-03-01

The paper addresses the selected aspects of the dynamic behaviour of mine hoists during the emergency braking phase. Basing on the model of the hoist and supported by theoretical backgrounds provided by the author (Wolny, 2016), analytical formulas are derived to determine the parameters of the braking system such that during an emergency braking it should guarantee that: - the maximal loading of the hoisting ropes should not exceed the rope breaking force, - deceleration of the conveyances being stopped should not exceed the admissible levels Results of the dynamic analysis of the mine hoist behaviour during an emergency braking phase summarised in this study can be utilised to support the design of conveyance and rope attachments by the fatigue endurance methods, with an aim to adapt it to the specified operational parameters of the hoisting installation (Eurokod 3).

Electromechanical imitator of antilock braking modes of wheels with pneumatic tire and its application for the runways friction coefficient measurement

NASA Astrophysics Data System (ADS)

Putov, A. V.; Kopichev, M. M.; Ignatiev, K. V.; Putov, V. V.; Stotckaia, A. D.

2017-01-01

In this paper it is considered a discussion of the technique that realizes a brand new method of runway friction coefficient measurement based upon the proposed principle of measuring wheel braking control for the imitation of antilock braking modes that are close to the real braking modes of the aircraft chassis while landing that are realized by the aircraft anti-skid systems. Also here is the description of the model of towed measuring device that realizes a new technique of runway friction coefficient measuring, based upon the measuring wheel braking control principle. For increasing the repeatability accuracy of electromechanical braking imitation system the sideslip (brake) adaptive control system is proposed. Based upon the Burkhard model and additive random processes several mathematical models were created that describes the friction coefficient arrangement along the airstrip with different qualitative adjectives. Computer models of friction coefficient measuring were designed and first in the world the research of correlation between the friction coefficient measuring results and shape variations, intensity and cycle frequency of the measuring wheel antilock braking modes. The sketch engineering documentation was designed and prototype of the latest generation measuring device is ready to use. The measuring device was tested on the autonomous electromechanical examination laboratory treadmill bench. The experiments approved effectiveness of method of imitation the antilock braking modes for solving the problem of correlation of the runway friction coefficient measuring.

Neural-network hybrid control for antilock braking systems.

PubMed

Lin, Chih-Min; Hsu, C F

2003-01-01

The antilock braking systems are designed to maximize wheel traction by preventing the wheels from locking during braking, while also maintaining adequate vehicle steerability; however, the performance is often degraded under harsh road conditions. In this paper, a hybrid control system with a recurrent neural network (RNN) observer is developed for antilock braking systems. This hybrid control system is comprised of an ideal controller and a compensation controller. The ideal controller, containing an RNN uncertainty observer, is the principal controller; and the compensation controller is a compensator for the difference between the system uncertainty and the estimated uncertainty. Since for dynamic response the RNN has capabilities superior to the feedforward NN, it is utilized for the uncertainty observer. The Taylor linearization technique is employed to increase the learning ability of the RNN. In addition, the on-line parameter adaptation laws are derived based on a Lyapunov function, so the stability of the system can be guaranteed. Simulations are performed to demonstrate the effectiveness of the proposed NN hybrid control system for antilock braking control under various road conditions.

Braking and cornering studies on an air cushion landing system

NASA Technical Reports Server (NTRS)

Daugherty, R. H.

1983-01-01

An experimental investigation was conducted to evaluate several concepts for braking and steering a vehicle equipped with an air cushion landing system (ACLS). The investigation made use of a modified airboat equipped with an ACLS. Braking concepts were characterized by the average deceleration of the vehicle. Reduced lobe flow and cavity venting braking concepts were evaluated in this program. The cavity venting braking concept demonstrated the best performance, producing decelerations on the test vehicle on the same order as moderate braking with conventional wheel brakes. Steering concepts were evaluated by recording the path taken while attempting to follow a prescribed maneuver. The steering concepts evaluated included using rudders only, using differential lobe flow, and using rudders combined with a lightly loaded, nonsteering center wheel. The latter concept proved to be the most accurate means of steering the vehicle on the ACLS, producing translational deviations two to three times higher than those from conventional nose-gear steering. However, this concept was still felt to provide reasonably precise steering control for the ACLS-equipped vehicle.

Capacitor regenerative braking system of electric wheelchair for senior citizen based on variable frequency chopper control.

PubMed

Takahashi, Yoshiaki; Seki, Hirokazu

2009-01-01

This paper proposes a novel regenerative braking control system of electric wheelchairs for senior citizen. "Electric powered wheelchair", which generates the driving force by electric motors according to the human operation, is expected to be widely used as a mobility support system for elderly people. This study focuses on the braking control to realize the safety and smooth stopping motion using the regenerative braking control technique based on fuzzy algorithm. The ride quality improvement and energy recycling can be expected by the proposed control system with stopping distance estimation and variable frequency control on the step-up/down chopper type of capacitor regenerative circuit. Some driving experiments confirm the effectiveness of the proposed control system.

Regenerative braking strategies, vehicle safety and stability control systems: critical use-case proposals

NASA Astrophysics Data System (ADS)

Oleksowicz, Selim A.; Burnham, Keith J.; Southgate, Adam; McCoy, Chris; Waite, Gary; Hardwick, Graham; Harrington, Cian; McMurran, Ross

2013-05-01

The sustainable development of vehicle propulsion systems that have mainly focused on reduction of fuel consumption (i.e. CO2 emission) has led, not only to the development of systems connected with combustion processes but also to legislation and testing procedures. In recent years, the low carbon policy has made hybrid vehicles and fully electric vehicles (H/EVs) popular. The main virtue of these propulsion systems is their ability to restore some of the expended energy from kinetic movement, e.g. the braking process. Consequently new research and testing methods for H/EVs are currently being developed. This especially concerns the critical 'use-cases' for functionality tests within dynamic events for both virtual simulations, as well as real-time road tests. The use-case for conventional vehicles for numerical simulations and road tests are well established. However, the wide variety of tests and their great number (close to a thousand) creates a need for selection, in the first place, and the creation of critical use-cases suitable for testing H/EVs in both virtual and real-world environments. It is known that a marginal improvement in the regenerative braking ratio can significantly improve the vehicle range and, therefore, the economic cost of its operation. In modern vehicles, vehicle dynamics control systems play the principal role in safety, comfort and economic operation. Unfortunately, however, the existing standard road test scenarios are insufficient for H/EVs. Sector knowledge suggests that there are currently no agreed tests scenarios to fully investigate the effects of brake blending between conventional and regenerative braking as well as the regenerative braking interaction with active driving safety systems (ADSS). The paper presents seven manoeuvres, which are considered to be suitable and highly informative for the development and examination of H/EVs with regenerative braking capability. The critical manoeuvres presented are considered to be appropriate for examination of the regenerative braking mode according to ADSS. The manoeuvres are also important for investigation of regenerative braking system properties/functionalities that are specified by the legal requirements concerning H/EVs braking systems. The last part of this paper shows simulation results for one of the proposed manoeuvres that explicitly shows the usefulness of the manoeuvre.

78 FR 44189 - Petition for Modification of Single Car Air Brake Test Procedures

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-23

...] Petition for Modification of Single Car Air Brake Test Procedures In accordance with Part 232 of Title 49... Administration (FRA) per 49 CFR 232.307 to modify the single car air brake test procedures located in AAR Standard S-486, Code of Air Brake System Tests for Freight Equipment-- Single Car Test, and required...

75 FR 49365 - Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146-100A and -200A Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-13

... lift to ensure that the wheel brakes can provide the necessary speed reduction. * * * * * The effects... brakes can provide the necessary speed reduction. A review of the changing operational profile of the... landing to provide aerodynamic braking and to dump lift to ensure that the wheel brakes can provide the...

Age and gender differences in time to collision at braking from the 100-Car Naturalistic Driving Study.

PubMed

Montgomery, Jade; Kusano, Kristofer D; Gabler, Hampton C

2014-01-01

Forward collision warning (FCW) is an active safety system that aims to mitigate the effect of forward collisions by warning the driver of objects in front of the vehicle. Success of FCW relies on how drivers react to the alerts. Drivers who receive too many warnings that they deem as unnecessary-that is, nuisance alarms-may grow to distrust and turn the system off. To reduce the perception of nuisance alarms, FCW systems can be tailored to individual driving styles, but these driving styles must first be characterized. The objective of this study was to characterize differences in braking behavior between age and gender groups in car-following scenarios using data from the 100-Car Naturalistic Driving Study. The data source for this study was the 100-Car Naturalistic Driving Study, which recorded the driving of 108 primary drivers for approximately a year. Braking behavior was characterized in terms of time to collision (TTC) at brake application, a common metric used in the design of warning thresholds of FCW. Because of the large volume of data analyzed, the TTC at which drivers braked during car-following situations was collected via an automated search algorithm. The minimum TTC for each vehicle speed 10 mph increment from 10 mph to 80 mph was recorded for each driver. Mixed model analysis of variance was used to examine the differences between age and gender groups. In total, 527,861 brake applications contained in 11,503 trips were analyzed. Differences in TTC at braking were statistically significant for age and gender (P<.01 for both cases). Males age 18-20 (n=7) had the lowest average minimum TTC at braking of 2.5±0.8 s, and females age 31-50 (n=6) had the highest average minimum TTC at braking of 6.4±0.9 s. On average, women (n=32) braked at a TTC 1.3 s higher than men (n=52). Age was a statistically significant factor for TTC at braking between participants under 30 (n=42) and participants over 30 (n=42), with the latter braking 1.7 s on average before the former. No statistical significance was found between ages 18-20 (n=15) and 21-30 (n=27) or between ages 31-50 (n=23) and 50+(n=19). There are clear statistical differences in TTC at braking for both gender and those over 30 vs. those under 30. Designers of FCW systems can use the data found in this study to tailor alert timings to the target demographic of a vehicle when designing forward collision warning systems. Appropriate alert timings for FCW systems will maximize effectiveness in collision reduction and mitigation.

HLH Drive System

DTIC Science & Technology

1977-09-01

Material Comparison ....... .. 359 D-16 Comparison Chart - Rotor Brake Designs, Boeing Vertol, HLH ........... 360 D-17 Conventional Steel Disk Dynamic ...engines off. 0 In the event of a rotor brake caliper or disc failure, the system shall preclude damage to critical dynamic components. * The rotor brake... Dynamic System Test Rig (DSTR) shown in Figure. .8 provided a means for integrating and testing the aft and conbiner trans- missions, the aft rotor , thr’ee

Modeling Hydraulic Components for Automated FMEA of a Braking System

DTIC Science & Technology

2014-12-23

Modeling Hydraulic Components for Automated FMEA of a Braking System Peter Struss, Alessandro Fraracci Tech. Univ. of Munich, 85748 Garching...Germany struss@in.tum.de ABSTRACT This paper presents work on model-based automation of failure-modes-and-effects analysis ( FMEA ) applied to...the hydraulic part of a vehicle braking system. We describe the FMEA task and the application problem and outline the foundations for automating the

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces - A velocity-rate-controlled, pressure-bias-modulated system

NASA Technical Reports Server (NTRS)

Stubbs, S. M.; Tanner, J. A.

1976-01-01

During maximum braking the average ratio of drag-force friction coefficient developed by the antiskid system to maximum drag-force friction coefficient available at the tire/runway interface was higher on dry surfaces than on wet surfaces. The gross stopping power generated by the brake system on the dry surface was more than twice that obtained on the wet surfaces. With maximum braking applied, the average ratio of side-force friction coefficient developed by the tire under antiskid control to maximum side-force friction available at the tire/runway interface of a free-rolling yawed tire was shown to decrease with increasing yaw angle. Braking reduced the side-force friction coefficient on a dry surface by 75 percent as the wheel slip ratio was increased to 0.3; on a flooded surface the coefficient dropped to near zero for the same slip ratio. Locked wheel skids were observed when the tire encountered a runway surface transition from dry to flooded, due in part to the response time required for the system to sense abrupt changes in the runway friction; however, the antiskid system quickly responded by reducing brake pressure and cycling normally during the remainder of the run on the flooded surface.

Vehicle brake testing system

DOEpatents

Stevens, Samuel S [Harriman, TN; Hodgson, Jeffrey W [Lenoir City, TN

2002-11-19

This invention relates to a force measuring system capable of measuring forces associated with vehicle braking and of evaluating braking performance. The disclosure concerns an invention which comprises a first row of linearly aligned plates, a force bearing surface extending beneath and beside the plates, vertically oriented links and horizontally oriented links connecting each plate to a force bearing surface, a force measuring device in each link, a transducer coupled to each force measuring device, and a computing device coupled to receive an output signal from the transducer indicative of measured force in each force measuring device. The present invention may be used for testing vehicle brake systems.

The effect of a braking device in reducing the ground impact forces inherent in plyometric training.

PubMed

Humphries, B J; Newton, R U; Wilson, G J

1995-02-01

As a consequence of performing plyometric type exercises, such as depth jumps, impact forces placed on the musculoskeletal system during landing can lead to a potential for injury. A reduction of impact forces upon landing could therefore contribute to reduce the risk of injury. Twenty subjects performed a series of loaded jumps for maximal height, with and without a brake mechanism designed to reduce impact force during landing. The braked jumps were performed on the Plyometric Power System (PPS) with its braking mechanism set at 75% of body weight during the downward phase. The non-braked condition involved jumps with no braking. Vertical ground reaction force data, sampled for 5.5 s at 550 Hz from a Kistler forceplate, were collected for each jump condition. The following parameters were then calculated: peak vertical force, time to peak force, passive impact impulse and maximum concentric force. The brake served to significantly (p < 0.01) reduce peak impact force by 155% and passive impact impulse by 200%. No significant differences were found for peak concentric force production. The braking mechanism of the PPS significantly reduced ground impact forces without impeding concentric force production. The reduction in eccentric loading, using the braking mechanism, may reduce the incidence of injury associated with landings from high intensity plyometric exercises.

Chaos in brake squeal noise

NASA Astrophysics Data System (ADS)

Oberst, S.; Lai, J. C. S.

2011-02-01

Brake squeal has become an increasing concern to the automotive industry because of warranty costs and the requirement for continued interior vehicle noise reduction. Most research has been directed to either analytical and experimental studies of brake squeal mechanisms or the prediction of brake squeal propensity using finite element methods. By comparison, there is a lack of systematic analysis of brake squeal data obtained from a noise dynamometer. It is well known that brake squeal is a nonlinear transient phenomenon and a number of studies using analytical and experimental models of brake systems (e.g., pin-on-disc) indicate that it could be treated as a chaotic phenomenon. Data obtained from a full brake system on a noise dynamometer were examined with nonlinear analysis techniques. The application of recurrence plots reveals chaotic structures even in noisy data from the squealing events. By separating the time series into different regimes, lower dimensional attractors are isolated and quantified by dynamic invariants such as correlation dimension estimates or Lyapunov exponents. Further analysis of the recurrence plot of squealing events by means of recurrence quantification analysis measures reveals different regimes of laminar and random behaviour, periodicity and chaos-forming recurrent transitions. These results help to classify brake squeal mechanisms and to enhance understanding of friction-related noise phenomena.

Status report on activations systems, centrifugal switch, of a 30 kW Riisager molle with 10 m wing span (in Dutch)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ethelfeld, J.

The report is made to help the owners and the technical personnel of old wind mills: to make a new induction sensor which gives a quick activation of the original brake activation system; to build a new brake activation system, with its own new independent induction sensor system; and to change the (original) centrifugal switch for the brake so that a quicker activation is obtained.

Potential Occupant Injury Reduction in Pre-Crash System Equipped Vehicles in the Striking Vehicle of Rear-end Crashes

PubMed Central

Kusano, Kristofer D.; Gabler, Hampton C.

2010-01-01

To mitigate the severity of rear-end and other collisions, Pre-Crash Systems (PCS) are being developed. These active safety systems utilize radar and/or video cameras to determine when a frontal crash, such as a front-to-back rear-end collisions, is imminent and can brake autonomously, even with no driver input. Of these PCS features, the effects of autonomous pre-crash braking are estimated. To estimate the maximum potential for injury reduction due to autonomous pre-crash braking in the striking vehicle of rear-end crashes, a methodology is presented for determining 1) the reduction in vehicle crash change in velocity (ΔV) due to PCS braking and 2) the number of injuries that could be prevented due to the reduction in collision severity. Injury reduction was only performed for belted drivers, as unbelted drivers have an unknown risk of being thrown out of position. The study was based on 1,406 rear-end striking vehicles from NASS / CDS years 1993 to 2008. PCS parameters were selected from realistic values and varied to examine the effect on system performance. PCS braking authority was varied from 0.5 G’s to 0.8 G’s while time to collision (TTC) was held at 0.45 seconds. TTC was then varied from 0.3 second to 0.6 seconds while braking authority was held constant at 0.6 G’s. A constant braking pulse (step function) and ramp-up braking pulse were used. The study found that automated PCS braking could reduce the crash ΔV in rear-end striking vehicles by an average of 12% – 50% and avoid 0% – 14% of collisions, depending on PCS parameters. Autonomous PCS braking could potentially reduce the number of injured drivers who are belted by 19% to 57%. PMID:21050603

Evaluating impacts of different longitudinal driver assistance systems on reducing multi-vehicle rear-end crashes during small-scale inclement weather.

PubMed

Li, Ye; Xing, Lu; Wang, Wei; Wang, Hao; Dong, Changyin; Liu, Shanwen

2017-10-01

Multi-vehicle rear-end (MVRE) crashes during small-scale inclement (SSI) weather cause high fatality rates on freeways, which cannot be solved by traditional speed limit strategies. This study aimed to reduce MVRE crash risks during SSI weather using different longitudinal driver assistance systems (LDAS). The impact factors on MVRE crashes during SSI weather were firstly analyzed. Then, four LDAS, including Forward collision warning (FCW), Autonomous emergency braking (AEB), Adaptive cruise control (ACC) and Cooperative ACC (CACC), were modeled based on a unified platform, the Intelligent Driver Model (IDM). Simulation experiments were designed and a large number of simulations were then conducted to evaluate safety effects of different LDAS. Results indicate that the FCW and ACC system have poor performance on reducing MVRE crashes during SSI weather. The slight improvement of sight distance of FCW and the limitation of perception-reaction time of ACC lead the failure of avoiding MVRE crashes in most scenarios. The AEB system has the better effect due to automatic perception and reaction, as well as performing the full brake when encountering SSI weather. The CACC system has the best performance because wireless communication provides a larger sight distance and a shorter time delay at the sub-second level. Sensitivity analyses also indicated that the larger number of vehicles and speed changes after encountering SSI weather have negative impacts on safety performances. Results of this study provide useful information for accident prevention during SSI weather. Copyright © 2017 Elsevier Ltd. All rights reserved.

Design of the Electronic Brake Pressure Modulator Using a Direct Adaptive Fuzzy Controller in Commercial Vehicles for the Safety of Braking in Fail

NASA Astrophysics Data System (ADS)

Kim, Hunmo

In the brake systems, it is important to reduce the rear brake pressure in order to secure the safety of the vehicle in braking. So, there was some research that reduced and controlled the rear brake pressure exactly like a L. S. P. V and a E. L. S. P. V. However, the previous research has some weaknesses: the L. S. P. V is a mechanical system and its brake efficiency is lower than the efficiency of E. L. S. P. V. But, the cost of E. L. S. P. V is very higher so its application to the vehicle is very difficult. Additionally, when a fail appears in the circuit which controls the valves, the fail results in some wrong operation of the valves. But, the previous researchers didn't take the effect of fail into account. Hence, the efficiency of them is low and the safety of the vehicle is not confirmed. So, in this paper we develop a new economical pressure modulator that exactly controls brake pressure and confirms the safety of the vehicle in any case using a direct adaptive fuzzy controller.

Proceedings of the ISTVS (International Society for Terrain-Vehicle Systems) Workshop on Measurement and Evaluation of Tire Performance under Winter Conditions, Alta, Utah, 11-14 April 1983.

DTIC Science & Technology

1985-09-01

Transducers capable of measuring electro-hydraulic control system which fore-aft and vertical load on a driven controls the brake system to deactivate tire...power. * axle allows design of all load-carrying - System logic power. ENGINE I EXTERNAL COMPARTMENT COMPONENTS CAB Brake Levelin system I trans... brake con- The TWS DAS was designed to 1) pro- trol system . vide onboard data sampling and filtering, A simplified truck operational flow chart 2) make

Analysis of Braking Behavior of Train Drivers to Detect Unusual Driving

NASA Astrophysics Data System (ADS)

Marumo, Yoshitaka; Tsunashima, Hitoshi; Kojima, Takashi; Hasegawa, Yasushi

The safety devices for train systems are activated in emergency situations when a risk becomes obvious, and the emergency brake is applied. If such systems are faulty, the drivers' operating errors may cause immediate accidents. So it is necessary to evaluate potential risks by detecting improper driving behavior before overt risks appear. This study analyzes the driving behavior of train drivers using a train-driving simulator. We focus on braking behavior when approaching a station. Two methods for detecting unusual braking operation are examined by giving drivers mental calculation problems as a mental workload. The first is a method monitoring the driver's brake handle operation, and the second is a method measuring vehicle deceleration. These methods make it possible to detect unusual driving.

Regenerative braking systems with torsional springs made of carbon nanotube yarn

NASA Astrophysics Data System (ADS)

Liu, S.; Martin, C.; Lashmore, D.; Schauer, M.; Livermore, C.

2014-11-01

The demonstration of large stroke, high energy density and high power density torsional springs based on carbon nanotube (CNT) yarns is reported, as well as their application as an energy-storing actuator for regenerative braking systems. Originally untwisted CNT yarn is cyclically loaded and unloaded in torsion, with the maximum rotation angle increasing until failure. The maximum extractable energy density is measured to be as high as 6.13 kJ/kg. The tests also reveal structural reorganization and hysteresis in the torsional loading curves. A regenerative braking system is built to capture the kinetic energy of a wheel and store it as elastic energy in twisted CNT yarns. When the yam's twist is released, the stored energy reaccelerates the wheel. The measured energy and mean power densities of the CNT yarns in the simple regenerative braking system are up to 4.69 kJ/kg and 1.21 kW/kg, respectively. A slightly lower energy density of up to 1.23 kJ/kg and a 0.29 kW/kg mean power density are measured for the CNT yarns in a more complex system that mimics a unidirectional rotating regenerative braking mechanism. The lower energy densities for CNT yarns in the regenerative braking systems as compared with the yarns themselves reflect the frictional losses of the regenerative systems.

Anti-lock braking system (ABS) and regenerative braking system (RBS) in hybrid electric vehicle for smart transportation system

NASA Astrophysics Data System (ADS)

Evuri, Geetha Reddy; Rao, G. Srinivasa; Reddy, T. Ramasubba; Reddy, K. Srinivasa

2018-04-01

Pulse width modulation (PWM) based (a non-consistent) breaking system is used to keep the wheels from being bolted in the proposed antilock breaking system (ABS). Using this method a better hold of the street by wheels is possible and halting separations likewise diminish essentially particularly on precarious street surfaces like frosty or wet streets. The active vitality of the wheel is by and large lost amid braking as warmth because of grinding among brake cushions. This vitality can be recuperated using regenerative braking systems (RBS). In this strategy, the overabundance vitality is put away incidentally in capacitor banks before it gets changed over to warm vitality and is squandered. This framework delays the battery life by reviving the battery utilizing the put away vitality. Subsequently the mileage of the electric vehicle likewise increments as it can travel more separation in a solitary battery charge. These two techniques together help make electric vehicle vitality productive and more secure and less demanding to utilize subsequently anticipating and diminishing the quantity of mischance's.

Analysis of the stability of PTW riders in autonomous braking scenarios.

PubMed

Symeonidis, Ioannis; Kavadarli, Gueven; Erich, Schuller; Graw, Matthias; Peldschus, Steffen

2012-11-01

While fatalities of car occupants in the EU decreased remarkably over the last decade, Powered Two Wheelers (PTWs) fatalities still increase following the increase of PTW ownership. Autonomous braking systems have been implemented in several types of vehicles and are presently addressed by research in the field of PTWs. A major concern in this context is the rider stability. Experiments with volunteers were performed in order to find out whether autonomous braking for PTWs will produce a greater instability of the rider in comparison to manual braking. The PTW's braking conditions were simulated in a laboratory with a motorcycle mock-up mounted on a sled, which was accelerated with an average of 0.35 g. The motion of the rider was captured in autonomous braking scenarios with and without pre-warning as well as in manual braking scenarios. No significant differences between the scenarios were found with respect to maximum forward displacement of the volunteer's torso and head (p<0.05). By performing clustering analysis on two kinematic parameters, two different strategies of the volunteers were identified. They were not related to the braking scenarios. A relation of the clusters with the initial posture represented by the elbow angle was revealed (p<0.05). It is concluded that autonomous braking at low deceleration will not cause significant instabilities of the rider in comparison to manual braking in idealized laboratory conditions. Based on this, further research into the development and implementation of autonomous braking systems for PTWs, e.g. by extensive riding tests, seems valuable. Copyright © 2011 Elsevier Ltd. All rights reserved.

The influence of tyre contact patch and on the stopping distance of automotive vehicles

NASA Astrophysics Data System (ADS)

Selig, M.; Ball, A.; Ash, J.; Schmidt, K.

2012-05-01

This contribution presents the experimental tests results about the influence of the tyre contact patch on the stopping distance of automotive vehicles. The objective of the performed tests is the evaluation of the effect of tyre inflation pressure, hence the resulting tyre contact patch on the braking system and the brake distance. The conditions of the experiment are a dry and level road surface without steering inputs. To record scientific results, a brake robot system is used. The benefit of a robotic system is the elimination of the interfering variable driver, who is not able to apply the brake system at the same time with the same force. State-of-the-art data acquisition tools are used to log the data.

Technology Insertion-Engineering Services Process Characterization. Task Order No. 1. Book 1 of 3. Database Documentation Book. OO-ALC MANPGP (Overview Layouts)

DTIC Science & Technology

1989-12-15

Missile Systems Company 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NUMBER McDonnell Douglas Missile Systems...SEQUENCE NO. B008 MCDONNELL DOUGLAS McDonnefl Douglas Missile Systems Company St. Louis, Missouri 63166-0516 (314) 232-0232 91-02815 Distribution nt pm rt...Systems Company 7.1- 1 2. TASK ORDER NO. 1 PROCESS CHARACTERIZATION The brake assembly subunit is responsible for the assembly of brakes. Brakes enter

Base Vehicle Equipment, Special Vehicle, General Purpose Vehicle, and Vehicle Body Mechanics Career Ladders, AFSs 472X0, 472X1A/B/C/D, 472X2 and 472X3.

DTIC Science & Technology

1982-08-01

brakes , belts, and carburetors; servicing air cleaners, oil systems , and drive belts; and lubricating vehicles. Although the six distinct jobs...vehicle systems . General Repair Mechanics repaired, inspected, serviced, and maintained electrical, brake , suspension, and other vehicle systems . This...installing intake or exhaust manifolds removing or installing parking- brake cables removing or’installing head assemblies inspecting gasoline fuel system

Solid state control system for oil well bailer pump

DOE Office of Scientific and Technical Information (OSTI.GOV)

Senghaas, K. A.; Senghaas, P.

1985-05-14

A solid state switching controller for use with various types of oil well bailer pumps. Individually programmable steps with lockouts provide multiple mutual exclusivity between various circuit operations. A trickle charge battery system powers the control circuits. A tank overflow float protects against oil spillage. An automatic production rate adjustment circuit is provided which increases cycle time in proportion to the rate of production. The circuit includes a low power voltage detector for disabling the control circuits until the line voltage is acceptable. A three-phase power and control system with an isolation transformer for the controls avoids unreliable ground connections.more » The timers include a dividing circuit with an RC circuit. All power actuated apparatus are actuated by triac switches which are controlled by an opto driver. The bailer brake is pulse actuated for allowing the bailer to sink into crude oil without excess cable looseness.« less

High-Speed RaPToRS

NASA Astrophysics Data System (ADS)

Henchen, Robert; Esham, Benjamin; Becker, William; Pogozelski, Edward; Padalino, Stephen; Sangster, Thomas; Glebov, Vladimir

2008-11-01

The High-Speed Rapid Pneumatic Transport of Radioactive Samples (HS-RaPToRS) system, designed to quickly and safely move radioactive materials, was assembled and tested at the Mercury facility of the Naval Research Laboratory (NRL) in Washington D.C. A sample, which is placed inside a four-inch-diameter carrier, is activated before being transported through a PVC tube via airflow. The carrier travels from the reaction chamber to the end station where it pneumatically brakes prior to the gate. A magnetic latch releases the gate when the carrier arrives and comes to rest. The airflow, optical carrier-monitoring devices, and end gate are controlled manually or automatically with LabView software. The installation and testing of the RaPToRS system at NRL was successfully completed with transport times of less than 3 seconds. The speed of the carrier averaged 16 m/s. Prospective facilities for similar systems include the Laboratory for Laser Energetics and the National Ignition Facility.

Vehicle tracking for an evasive manoeuvres assistant using low-cost ultrasonic sensors.

PubMed

Jiménez, Felipe; Naranjo, José E; Gómez, Oscar; Anaya, José J

2014-11-28

Many driver assistance systems require knowledge of the vehicle environment. As these systems are increasing in complexity and performance, this knowledge of the environment needs to be more complete and reliable, so sensor fusion combining long, medium and short range sensors is now being used. This paper analyzes the feasibility of using ultrasonic sensors for low cost vehicle-positioning and tracking in the lane adjacent to the host vehicle in order to identify free areas around the vehicle and provide information to an automatic avoidance collision system that can perform autonomous braking and lane change manoeuvres. A laser scanner is used for the early detection of obstacles in the direction of travel while two ultrasonic sensors monitor the blind spot of the host vehicle. The results of tests on a test track demonstrate the ability of these sensors to accurately determine the kinematic variables of the obstacles encountered, despite a clear limitation in range.

Brake System Design Optimization : Volume 2. Supplemental Data.

DOT National Transportation Integrated Search

1981-04-01

Existing freight car braking systems, components, and subsystems are characterized both physically and functionally, and life-cycle costs are examined. Potential improvements to existing systems previously proposed or available are identified and des...

Brake System Design Optimization. Volume II : Supplemental Data.

DOT National Transportation Integrated Search

1981-06-01

Existing freight car braking systems, components, and subsystems are characterized both physically and functionally, and life-cycle costs are examined. Potential improvements to existing systems previously proposed or available are identified and des...

KSC-04PD-1030

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, workers remove the Rudder Speed Brake panel on the vertical tail of the orbiter Atlantis. The Rudder Speed Brake is being removed for inspection and maintenance prior to Return to Flight. The vertical tail consists of a structural fin surface made of aluminum, the Rudder Speed Brake surface, a tip and a lower trailing edge. The rudder splits into two halves to serve as a speed brake. The vertical tail and Rudder Speed Brake are covered with a reusable thermal protection system. The Rudder Speed Brake is used to guide and slow the Shuttle as it comes in for a landing.

Analysis of Energy-Absorbing Foundations.

DTIC Science & Technology

1978-12-15

side rails. At the top of the rebound, air brakes are automatically activated which press against the rails and stop the table, preventing a second...for the same application to automobile bumpers , was greater than that used in an alternate design in which the tube was crushed axially, so it appears...shock mounts prepared by Burns [48]. Typi- cal non-linear, elastic, load-deflection curves are given for helical springs, pneumatic cylinders, hydraulic

Effect of train type on annoyance and acoustic features of the rolling noise.

PubMed

Kasess, Christian H; Noll, Anton; Majdak, Piotr; Waubke, Holger

2013-08-01

This study investigated the annoyance associated with the rolling noise of different railway stock. Passbys of nine train types (passenger and freight trains) equipped with different braking systems were recorded. Acoustic features showed a clear distinction of the braking system with the A-weighted energy equivalent sound level (LAeq) showing a difference in the range of 10 dB between cast-iron braked trains and trains with disk or K-block brakes. Further, annoyance was evaluated in a psychoacoustic experiment where listeners rated the relative annoyance of the rolling noise for the different train types. Stimuli with and without the original LAeq differences were tested. For the original LAeq differences, the braking system significantly affected the annoyance with cast-iron brakes being most annoying, most likely as a consequence of the increased wheel roughness causing an increased LAeq. Contribution of the acoustic features to the annoyance was investigated revealing that the LAeq explained up to 94% of the variance. For the stimuli without differences in the LAeq, cast-iron braked train types were significantly less annoying and the spectral features explained up to 60% of the variance in the annoyance. The effect of these spectral features on the annoyance of the rolling noise is discussed.

Brake System Design Optimization : Volume 1. A Survey and Assessment.

DOT National Transportation Integrated Search

1978-06-01

Existing freight car braking systems, components, and subsystems are characterized both physically and functionally, and life-cycle costs are examined. Potential improvements to existing systems previously proposed or available are identified and des...

Combined emergency braking and turning of articulated heavy vehicles

NASA Astrophysics Data System (ADS)

Morrison, Graeme; Cebon, David

2017-05-01

'Slip control' braking has been shown to reduce the emergency stopping distance of an experimental heavy goods vehicle by up to 19%, compared to conventional electronic/anti-lock braking systems (EBS). However, little regard has been given to the impact of slip control braking on the vehicle's directional dynamics. This paper uses validated computer models to show that slip control could severely degrade directional performance during emergency braking. A modified slip control strategy, 'attenuated slip demand' (ASD) control, is proposed in order to rectify this. Results from simulations of vehicle performance are presented for combined braking and cornering manoeuvres with EBS and slip control braking with and without ASD control. The ASD controller enables slip control braking to provide directional performance comparable with conventional EBS while maintaining a substantial stopping distance advantage. The controller is easily tuned to work across a wide range of different operating conditions.

Driver braking behavior analysis to improve autonomous emergency braking systems in typical Chinese vehicle-bicycle conflicts.

PubMed

Duan, Jingliang; Li, Renjie; Hou, Lian; Wang, Wenjun; Li, Guofa; Li, Shengbo Eben; Cheng, Bo; Gao, Hongbo

2017-11-01

Bicycling is one of the fundamental modes of transportation especially in developing countries. Because of the lack of effective protection for bicyclists, vehicle-bicycle (V-B) accident has become a primary contributor to traffic fatalities. Although AEB (Autonomous Emergency Braking) systems have been developed to avoid or mitigate collisions, they need to be further adapted in various conflict situations. This paper analyzes the driver's braking behavior in typical V-B conflicts of China to improve the performance of Bicyclist-AEB systems. Naturalistic driving data were collected, from which the top three scenarios of V-B accidents in China were extracted, including SCR (a bicycle crossing the road from right while a car is driving straight), SCL (a bicycle crossing the road from left while a car is driving straight) and SSR (a bicycle swerving in front of the car from right while a car is driving straight). For safety and data reliability, a driving simulator was employed to reconstruct these three scenarios and some 25 licensed drivers were recruited for braking behavior analysis. Results revealed that driver's braking behavior was significantly influenced by V-B conflict types. Pre-decelerating behaviors were found in SCL and SSR conflicts, whereas in SCR the subjects were less vigilant. The brake reaction time and brake severity in lateral V-B conflicts (SCR and SCL) was shorter and higher than that in longitudinal conflicts (SSR). The findings improve their applications in the Bicyclist-AEB and test protocol enactment to enhance the performance of Bicyclist-AEB systems in mixed traffic situations especially for developing countries. Copyright © 2017 Elsevier Ltd. All rights reserved.

Braking distance algorithm for autonomous cars using road surface recognition

NASA Astrophysics Data System (ADS)

Kavitha, C.; Ashok, B.; Nanthagopal, K.; Desai, Rohan; Rastogi, Nisha; Shetty, Siddhanth

2017-11-01

India is yet to accept semi/fully - autonomous cars and one of the reasons, was loss of control on bad roads. For a better handling on these roads we require advanced braking and that can be done by adapting electronics into the conventional type of braking. In Recent years, the automation in braking system led us to various benefits like traction control system, anti-lock braking system etc. This research work describes and experiments the method for recognizing road surface profile and calculating braking distance. An ultra-sonic surface recognition sensor, mounted underneath the car will send a high frequency wave on to the road surface, which is received by a receiver with in the sensor, it calculates the time taken for the wave to rebound and thus calculates the distance from the point where sensor is mounted. A displacement graph will be plotted based on the output of the sensor. A relationship can be derived between the displacement plot and roughness index through which the friction coefficient can be derived in Matlab for continuous calculation throughout the distance travelled. Since it is a non-contact type of profiling, it is non-destructive. The friction coefficient values received in real-time is used to calculate optimum braking distance. This system, when installed on normal cars can also be used to create a database of road surfaces, especially in cities, which can be shared with other cars. This will help in navigation as well as making the cars more efficient.

Human-simulated intelligent control of train braking response of bridge with MRB

NASA Astrophysics Data System (ADS)

Li, Rui; Zhou, Hongli; Wu, Yueyuan; Wang, Xiaojie

2016-04-01

The urgent train braking could bring structural response menace to the bridge under passive control. Based on the analysis of breaking dynamics of a train-bridge vibration system, a magnetorheological elastomeric bearing (MRB) whose mechanical parameters are adjustable is designed, tested and modeled. A finite element method (FEM) is carried out to model and optimize a full scale vibration isolation system for railway bridge based on MRB. According to the model above, we also consider the effect of different braking stop positions on the vibration isolation system and classify the bridge longitudinal vibration characteristics into several cases. Because the train-bridge vibration isolation system has multiple vibration states and strongly coupling with nonlinear characteristics, a human-simulated intelligent control (HSIC) algorithm for isolating the bridge vibration under the impact of train braking is proposed, in which the peak shear force of pier top, the displacement of beam and the acceleration of beam are chosen as control goals. The simulation of longitudinal vibration control system under the condition of train braking is achieved by MATLAB. The results indicate that different braking stop positions significantly affect the vibration isolation system and the structural response is the most drastic when the train stops at the third cross-span. With the proposed HSIC smart isolation system, the displacement of bridge beam and peak shear force of pier top is reduced by 53.8% and 34.4%, respectively. Moreover, the acceleration of bridge beam is effectively controlled within limited range.

Apparatus for stopping a vehicle

DOEpatents

Wattenburg, Willard H [Walnut Creek, CA; McCallen, David B [Livermore, CA

2007-03-20

An apparatus for externally controlling one or more brakes on a vehicle having a pressurized fluid braking system. The apparatus can include a pressurizable vessel that is adapted for fluid-tight coupling to the braking system. Impact to the rear of the vehicle by a pursuit vehicle, shooting a target mounted on the vehicle or sending a signal from a remote control can all result in the fluid pressures in the braking system of the vehicle being modified so that the vehicle is stopped and rendered temporarily inoperable. A control device can also be provided in the driver's compartment of the vehicle for similarly rendering the vehicle inoperable. A driver or hijacker of the vehicle preferably cannot overcome the stopping action from the driver's compartment.

Modeling study of the ABS relay valve

NASA Astrophysics Data System (ADS)

Lei, Ming; Lin, Min; Guo, Bin; Luo, Zai; Xu, Weidong

2011-05-01

The ABS (anti-lock braking system) relay valve is the key component of anti-lock braking system in most commercial vehicles such as trucks, tractor-trailers, etc. In this paper, structure of ABS relay valve and its work theory were analyzed. Then a mathematical model of ABS relay valve, which was investigated by dividing into electronic part, magnetic part, pneumatic part and mechanical part, was set up. The displacement of spools and the response of pressure increasing, holding, releasing of ABS relay valve were simulated and analyzed under conditions of control pressure 500 KPa, braking pressure 600 KPa, atmospheric pressure 100 KPa and air temperature 310 K. Thisarticle provides reliable theory for improving the performance and efficiency of anti-lock braking system of vehicles.

Assessment and preliminary design of an energy buffer for regenerative braking in electric vehicles

NASA Technical Reports Server (NTRS)

Buchholz, R.; Mathur, A. K.

1979-01-01

Energy buffer systems, capable of storing the vehicle energy during braking and reusing this stored energy during acceleration, were examined. Some of these buffer systems when incorporated in an electric vehicle would result in an improvement in the performance and range under stop and go driving conditions. Buffer systems considered included flywheels, hydropneumatic, pneumatic, spring, and regenerative braking. Buffer ranking and rating criteria were established. Buffer systems were rated based on predicted range improvements, consumer acceptance, driveability, safety, reliability and durability, and initial and life cycle costs. A hydropneumatic buffer system was selected.

A parametric study of perforated muzzle brakes

NASA Astrophysics Data System (ADS)

Dillon, Robert E., Jr.; Nagamatsu, H. T.

1993-07-01

A firing test was conducted to study the parameters influencing the recoil efficiency and the blast characteristics of perforated muzzle brakes. Several scaled (20 mm) devices were tested as candidates for the 105 mm Armored Gun System (AGS). Recoil impulse, blast overpressures, muzzle velocity, sequential spark shadowgraphs, and photographs of the muzzle flash were obtained. A total of nine different perforated brakes were tested as well as a scaled M 198 double muzzle brake.

Downward Slope Driving Control for Electric Powered Wheelchair Based on Capacitor Regenerative Brake

NASA Astrophysics Data System (ADS)

Seki, Hirokazu; Takahashi, Yoshiaki

This paper describes a novel capacitor regenerative braking control scheme of electric powered wheelchairs for efficient driving on downward slopes. An electric powered wheelchair, which generates the driving force by electric motors, is expected to be widely used as a mobility support system for elderly people and disabled people; however the energy efficiency has to be further improved because it is driven only by battery energy. This study proposes a capacitor regenerative braking circuit and two types of velocity control schemes with variable duty ratio. The proposed regenerative braking circuit is based on the step-up/down circuit with additional resistance and connects right and left motors in series in order to obtain a larger braking power. Some driving experiments on a practical downward slope show the effectiveness of the proposed control system.

Surrogate models for efficient stability analysis of brake systems

NASA Astrophysics Data System (ADS)

Nechak, Lyes; Gillot, Frédéric; Besset, Sébastien; Sinou, Jean-Jacques

2015-07-01

This study assesses capacities of the global sensitivity analysis combined together with the kriging formalism to be useful in the robust stability analysis of brake systems, which is too costly when performed with the classical complex eigenvalues analysis (CEA) based on finite element models (FEMs). By considering a simplified brake system, the global sensitivity analysis is first shown very helpful for understanding the effects of design parameters on the brake system's stability. This is allowed by the so-called Sobol indices which discriminate design parameters with respect to their influence on the stability. Consequently, only uncertainty of influent parameters is taken into account in the following step, namely, the surrogate modelling based on kriging. The latter is then demonstrated to be an interesting alternative to FEMs since it allowed, with a lower cost, an accurate estimation of the system's proportions of instability corresponding to the influent parameters.

Evaluation strategy of regenerative braking energy for supercapacitor vehicle.

PubMed

Zou, Zhongyue; Cao, Junyi; Cao, Binggang; Chen, Wen

2015-03-01

In order to improve the efficiency of energy conversion and increase the driving range of electric vehicles, the regenerative energy captured during braking process is stored in the energy storage devices and then will be re-used. Due to the high power density of supercapacitors, they are employed to withstand high current in the short time and essentially capture more regenerative energy. The measuring methods for regenerative energy should be investigated to estimate the energy conversion efficiency and performance of electric vehicles. Based on the analysis of the regenerative braking energy system of a supercapacitor vehicle, an evaluation system for energy recovery in the braking process is established using USB portable data-acquisition devices. Experiments under various braking conditions are carried out. The results verify the higher efficiency of energy regeneration system using supercapacitors and the effectiveness of the proposed measurement method. It is also demonstrated that the maximum regenerative energy conversion efficiency can reach to 88%. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Detection of braking intention in diverse situations during simulated driving based on EEG feature combination.

PubMed

Kim, Il-Hwa; Kim, Jeong-Woo; Haufe, Stefan; Lee, Seong-Whan

2015-02-01

We developed a simulated driving environment for studying neural correlates of emergency braking in diversified driving situations. We further investigated to what extent these neural correlates can be used to detect a participant's braking intention prior to the behavioral response. We measured electroencephalographic (EEG) and electromyographic signals during simulated driving. Fifteen participants drove a virtual vehicle and were exposed to several kinds of traffic situations in a simulator system, while EEG signals were measured. After that, we extracted characteristic features to categorize whether the driver intended to brake or not. Our system shows excellent detection performance in a broad range of possible emergency situations. In particular, we were able to distinguish three different kinds of emergency situations (sudden stop of a preceding vehicle, sudden cutting-in of a vehicle from the side and unexpected appearance of a pedestrian) from non-emergency (soft) braking situations, as well as from situations in which no braking was required, but the sensory stimulation was similar to stimulations inducing an emergency situation (e.g., the sudden stop of a vehicle on a neighboring lane). We proposed a novel feature combination comprising movement-related potentials such as the readiness potential, event-related desynchronization features besides the event-related potentials (ERP) features used in a previous study. The performance of predicting braking intention based on our proposed feature combination was superior compared to using only ERP features. Our study suggests that emergency situations are characterized by specific neural patterns of sensory perception and processing, as well as motor preparation and execution, which can be utilized by neurotechnology based braking assistance systems.

49 CFR 232.601 - Scope.

Code of Federal Regulations, 2010 CFR

2010-10-01

... TRANSPORTATION BRAKE SYSTEM SAFETY STANDARDS FOR FREIGHT AND OTHER NON-PASSENGER TRAINS AND EQUIPMENT; END-OF-TRAIN DEVICES Electronically Controlled Pneumatic (ECP) Braking Systems § 232.601 Scope. This subpart... systems. This subpart also contains specific exceptions from various requirements contained in this part...

A parametric study of golf car and personal transport vehicle braking stability and their deficiencies.

PubMed

Seluga, Kristopher J; Baker, Lowell L; Ojalvo, Irving U

2009-07-01

This paper describes research and parametric analyses of braking effectiveness and directional stability for golf cars, personal transport vehicles (PTVs) and low speed vehicles (LSVs). It is shown that current designs, which employ brakes on only the rear wheels, can lead to rollovers if the brakes are applied while traveling downhill. After summarizing the current state of existing safety standards and brake system designs, both of which appear deficient from a safety perspective, a previously developed dynamic simulation model is used to identify which parameters have the greatest influence on the vehicles' yaw stability. The simulation results are then used to parametrically quantify which combination of these factors can lead to yaw induced rollover during hard braking. Vehicle velocity, steering input, path slope and tire friction are all identified as important parameters in determining braking stability, the effects of which on rollover propensity are presented graphically. The results further show that when vehicles are equipped with front brakes or four-wheel brakes, the probability of a yaw induced rollover is almost entirely eliminated. Furthermore, the parametric charts provided may be used as an aid in developing guidelines for golf car and PTV path design if rear brake vehicles are used.

Effects of cryogenic treatment on the wear properties of brake discs

NASA Astrophysics Data System (ADS)

Nadig, D. S.; Shivakumar, P.; Anoop, S.; Chinmay, Kulkarni; Divine, P. V.; Harsha, H. P.

2017-02-01

Disc brakes are invariably used in all the automobiles either to reduce the rotational speed of the wheel or to hold the vehicle stationary. During the braking action, the kinetic energy is converted into heat which can result in high temperatures resulting in fading of brake effects. Brake discs produced out of martensite stainless steel (SS410) are expected to exhibit high wear resistance properties with low value of coefficient of friction. These factors increase the useful life of the brake discs with minimal possibilities of brake fade. To study the effects of cryogenic treatment on the wear behaviour, two types of brake discs were cryotreated at 98K for 8 and 24 hours in a specially developed cryotreatment system using liquid nitrogen. Wear properties of the untreated and cryotreated test specimens were experimentally determined using the pin on disc type tribometer (ASTM G99-95). Similarly, the Rockwell hardness (HRC) of the specimens were tested in a hardness tester in accordance with ASTM E18. In this paper, the effects of cryotreatment on the wear and hardness properties of untreated and cryotreated brake discs are presented. Results indicate enhancement of wear properties and hardness after cryogenic treatment compared with the normal brakes discs.

Validity of a device designed to measure braking power in bicycle disc brakes.

PubMed

Miller, Matthew C; Fink, Philip W; Macdermid, Paul William; Perry, Blake G; Stannard, Stephen R

2017-07-21

Real-world cycling performance depends not only on exercise capacities, but also on efficiently traversing the bicycle through the terrain. The aim of this study was to determine if it was possible to quantify the braking done by a cyclist in the field. One cyclist performed 408 braking trials (348 on a flat road; 60 on a flat dirt path) over 5 days on a bicycle fitted with brake torque and angular velocity sensors to measure brake power. Based on Newtonian physics, the sum of brake work, aerodynamic drag and rolling resistance was compared with the change in kinetic energy in each braking event. Strong linear relationships between the total energy removed from the bicycle-rider system through braking and the change in kinetic energy were observed on the tar-sealed road (r 2  = 0.989; p < 0.0001) and the dirt path (r 2  = 0.952; p < 0.0001). T-tests revealed no difference between the total energy removed and the change in kinetic energy on the road (p = 0.715) or dirt (p = 0.128). This study highlights that brake torque and angular velocity sensors are valid for calculating brake power on the disc brakes of a bicycle in field conditions. Such a device may be useful for investigating cyclists' ability to traverse through various terrains.

76 FR 65777 - Proposed Agency Information Collection Activities; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-24

... the regulations governing freight power brakes and equipment in October 2008 by adding a new Subpart... being submitted for clearance by OMB as required by the PRA. Title: Inspection Brake System Safety Standards for Freight and Other Non-Passenger Trains and Equipment (Power Brakes and Drawbars). OMB Control...

49 CFR 570.5 - Service brake system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... CFR 571.105, on every new passenger car manufactured on or after January 1, 1968, and on other types... equipment manufacturer's specifications. Note the left to right brake force variance. (2) Road test. The..., inspecting front brake hoses through all wheel positions from full left to full right for conditions...

49 CFR 570.5 - Service brake system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... CFR 571.105, on every new passenger car manufactured on or after January 1, 1968, and on other types... equipment manufacturer's specifications. Note the left to right brake force variance. (2) Road test. The..., inspecting front brake hoses through all wheel positions from full left to full right for conditions...

The process of gas-dynamic design of pneumatic braking system using the baseline compressor

NASA Astrophysics Data System (ADS)

Novikova, Y.; Popov, G.; Goriachkin, E.; Baturin, O.; Zubanov, V.

2017-08-01

The article presents the results of work on the design of the air brake for testing of industrial gas turbine engines with free turbine. Designing of the air brake was performed on the basis of existing units using the program CFD - simulation Numeca FineTurbo. During the design the air brake arrangement was determined, which allows to utilize the required power to the shaft of the free turbine, increases stall margin of the air brake by waisting of the meridional flow channel. It was also made designing of the outlet guide vane to remove the residual twist. Unified nozzle also was designed to provide the air brake work at necessary points on the characteristic.

Vehicle Hybrid Braking Control Using Sliding Mode Control

NASA Astrophysics Data System (ADS)

Kasahara, Misawa; Kanai, Yuki; Shiraki, Ryoko; Mori, Yasuchika

Anti-lock brake system and brake-by-wire are proposed in the vehicle control using a brake, and the braking power is expected to be improved more than ever. The researches such as an application to the ABS of Siliding mode control which considered a actuator dynamics and a hybrid control of the brake using model reference adaptive control are done so far. However, in the former case, speed following that becomes a target exists physically impossible situation by saturation of tire frictional force because only speed following is done. In the latter, the model error is caused because the simulation model and the controller design model are different. Therefore, there is a problem that an accurate follow cannot be done. In this paper, the braking control is performed using the sliding mode control which has high robustness for disturbance that fulfils matching conditions. In so doing, it aims at the achievement of optimal braking control to switch wheel speed following to slip ratio following.

Optimisation of active suspension control inputs for improved performance of active safety systems

NASA Astrophysics Data System (ADS)

Čorić, Mirko; Deur, Joško; Xu, Li; Tseng, H. Eric; Hrovat, Davor

2018-01-01

A collocation-type control variable optimisation method is used to investigate the extent to which the fully active suspension (FAS) can be applied to improve the vehicle electronic stability control (ESC) performance and reduce the braking distance. First, the optimisation approach is applied to the scenario of vehicle stabilisation during the sine-with-dwell manoeuvre. The results are used to provide insights into different FAS control mechanisms for vehicle performance improvements related to responsiveness and yaw rate error reduction indices. The FAS control performance is compared to performances of the standard ESC system, optimal active brake system and combined FAS and ESC configuration. Second, the optimisation approach is employed to the task of FAS-based braking distance reduction for straight-line vehicle motion. Here, the scenarios of uniform and longitudinally or laterally non-uniform tyre-road friction coefficient are considered. The influences of limited anti-lock braking system (ABS) actuator bandwidth and limit-cycle ABS behaviour are also analysed. The optimisation results indicate that the FAS can provide competitive stabilisation performance and improved agility when compared to the ESC system, and that it can reduce the braking distance by up to 5% for distinctively non-uniform friction conditions.

Technology review for electronically controlled braking systems

DOT National Transportation Integrated Search

1998-09-22

Electronically Controlled Braking Systems (ECBS) offer many potential benefits to the trucking industry in the areas of safety, reliability, enhanced driver feedback, and maintainability. ECBS are being tested by a number of manufacturers. These syst...

Design, Fabrication and Evaluation of Prototype Wayside Brake Inspection Sensors

DOT National Transportation Integrated Search

1980-06-01

Prototype Wayside instrumentation has been designed, developed, and tested that proves the feasibility of measuring braking system effectiveness on moving rail cars. The instrumentation system includes a specially designed short section of instrument...

The technology applying of inflatable devices to access adaptation, movement and landing descent vehicle from Martian environment to the Earth conditions

NASA Astrophysics Data System (ADS)

Koryanov, Vsevolod V.; Kazakovtsev, Victor P.

2017-07-01

At present, the idea has emerged to use special inflatable braking device (IBD) which permits to implement the landing vehicle (LV) "soft" landing on the planet's surface without a parachute system. Braking device (BD) unfolds still at the extra-atmospheric flight stage to provide the LV passive stabilisation, and the entire apparatus together with the braking device is twisted around its longitudinal axis. The advantage of an inflatable BD over traditional non-rigid brakes - parachutes is that it can be used at the atmospheric stage of the descent, starting from hypersonic speeds, and ending subsonic ones. These main theses are implemented in the project MetNet and its sequel project RITD, using Entry, Descent and Landing System (EDLS) system [1].

An Attempt to Identify Indicators of Competence on Mechanical Maintenance Tasks.

DTIC Science & Technology

1979-01-01

them on the DA Form 2404. The vehicle is prepared as follows: 1. Left front wheel and drum removed. 2. Retracting spring disconnected. 3. Brake pedal...charging system. 8 2. Troubleshoot starting system circuit on Ml51Al/A2 truck. ii 3. Replace steering linkage on Ml5lAl/A2 truck. 8 4. Troubleshoot brakes ...Troubleshoot starting system circuit on MI51AI/A2 truck. 101 3. Replace steering linkage on MI51AI/A2 truck. 96 4. Troubleshoot brakes and controls

Predicting significant torso trauma.

PubMed

Nirula, Ram; Talmor, Daniel; Brasel, Karen

2005-07-01

Identification of motor vehicle crash (MVC) characteristics associated with thoracoabdominal injury would advance the development of automatic crash notification systems (ACNS) by improving triage and response times. Our objective was to determine the relationships between MVC characteristics and thoracoabdominal trauma to develop a torso injury probability model. Drivers involved in crashes from 1993 to 2001 within the National Automotive Sampling System were reviewed. Relationships between torso injury and MVC characteristics were assessed using multivariate logistic regression. Receiver operating characteristic curves were used to compare the model to current ACNS models. There were a total of 56,466 drivers. Age, ejection, braking, avoidance, velocity, restraints, passenger-side impact, rollover, and vehicle weight and type were associated with injury (p < 0.05). The area under the receiver operating characteristic curve (83.9) was significantly greater than current ACNS models. We have developed a thoracoabdominal injury probability model that may improve patient triage when used with ACNS.

Optical Generation of Fuzzy-Based Rules

NASA Astrophysics Data System (ADS)

Gur, Eran; Mendlovic, David; Zalevsky, Zeev

2002-08-01

In the last third of the 20th century, fuzzy logic has risen from a mathematical concept to an applicable approach in soft computing. Today, fuzzy logic is used in control systems for various applications, such as washing machines, train-brake systems, automobile automatic gear, and so forth. The approach of optical implementation of fuzzy inferencing was given by the authors in previous papers, giving an extra emphasis to applications with two dominant inputs. In this paper the authors introduce a real-time optical rule generator for the dual-input fuzzy-inference engine. The paper briefly goes over the dual-input optical implementation of fuzzy-logic inferencing. Then, the concept of constructing a set of rules from given data is discussed. Next, the authors show ways to implement this procedure optically. The discussion is accompanied by an example that illustrates the transformation from raw data into fuzzy set rules.

Data dependent systems approach to modal analysis Part 1: Theory

NASA Astrophysics Data System (ADS)

Pandit, S. M.; Mehta, N. P.

1988-05-01

The concept of Data Dependent Systems (DDS) and its applicability in the context of modal vibration analysis is presented. The ability of the DDS difference equation models to provide a complete representation of a linear dynamic system from its sampled response data forms the basis of the approach. The models are decomposed into deterministic and stochastic components so that system characteristics are isolated from noise effects. The modelling strategy is outlined, and the method of analysis associated with modal parameter identification is described in detail. Advantages and special features of the DDS methodology are discussed. Since the correlated noise is appropriately and automatically modelled by the DDS, the modal parameters are shown to be estimated very accurately and hence no preprocessing of the data is needed. Complex mode shapes and non-classical damping are as easily analyzed as the classical normal mode analysis. These features are illustrated by using simulated data in this Part I and real data on a disc-brake rotor in Part II.

Design and analysis of magneto rheological fluid brake for an all terrain vehicle

NASA Astrophysics Data System (ADS)

George, Luckachan K.; Tamilarasan, N.; Thirumalini, S.

2018-02-01

This work presents an optimised design for a magneto rheological fluid brake for all terrain vehicles. The actuator consists of a disk which is immersed in the magneto rheological fluid surrounded by an electromagnet. The braking torque is controlled by varying the DC current applied to the electromagnet. In the presence of a magnetic field, the magneto rheological fluid particle aligns in a chain like structure, thus increasing the viscosity. The shear stress generated causes friction in the surfaces of the rotating disk. Electromagnetic analysis of the proposed system is carried out using finite element based COMSOL multi-physics software and the amount of magnetic field generated is calculated with the help of COMSOL. The geometry is optimised and performance of the system in terms of braking torque is carried out. Proposed design reveals better performance in terms of braking torque from the existing literature.

Plasma brake model for preliminary mission analysis

NASA Astrophysics Data System (ADS)

Orsini, Leonardo; Niccolai, Lorenzo; Mengali, Giovanni; Quarta, Alessandro A.

2018-03-01

Plasma brake is an innovative propellantless propulsion system concept that exploits the Coulomb collisions between a charged tether and the ions in the surrounding environment (typically, the ionosphere) to generate an electrostatic force orthogonal to the tether direction. Previous studies on the plasma brake effect have emphasized the existence of a number of different parameters necessary to obtain an accurate description of the propulsive acceleration from a physical viewpoint. The aim of this work is to discuss an analytical model capable of estimating, with the accuracy required by a preliminary mission analysis, the performance of a spacecraft equipped with a plasma brake in a (near-circular) low Earth orbit. The simplified mathematical model is first validated through numerical simulations, and is then used to evaluate the plasma brake performance in some typical mission scenarios, in order to quantify the influence of the system parameters on the mission performance index.

The P-38 Lightning Aircraft: Lessons Learned for Future Weapon Systems Development

DTIC Science & Technology

2010-04-01

PMBOK TEL \\ u.s. WER List of ~cronyms iv Brake Horse Power Design-Build Team District of Columbia Department of Defense Department of...record. Despite unresolved issues like the flap and brake system problems and limited test hours, on 11 February 1939, Lieutenant Kelsey flew the XP-38...engine, giving the P-3 8 engines a 1425 brake horse power (BHP)22 rating. However, limitations of the integral wing leading edge intercoolers23 could

Existence and stability of limit cycles in control of anti-lock braking systems with two boundaries via perturbation theory

NASA Astrophysics Data System (ADS)

Köppen, Thomas; Küpper, Tassilo; Makarenkov, Oleg

2017-05-01

This paper presents a two-phase control logic for anti-lock braking systems (ABS). ABS are by now a standard component in every modern car, preventing the wheels from going into a lock situation where the wheels are fixed by the brake and the stopping distances are greatly prolonged. There are different approaches to such control logics. An ABS design proposed in recent literature controls the wheel's slip by creating stable limit cycles in the corresponding phase space. This design is modified via an analytical approach that is derived from perturbation theory. Simulation results document shorter braking distance compared to available tests in the literature.

Braking Analysis For Collision Avoidance-- Autonomous Braking System Performance Modeling And Benefits Analysis

DOT National Transportation Integrated Search

1996-05-24

THIS REPORT IS AN ANALYSIS OF THE BENEFITS OF A COLLISION AVOIDANCE SYSTEM IN REDUCING REAR-END CRASHES. THE COLLISION AVOIDANCE SYSTEM CONSIDERED IN THIS STUDY UTILIZES THE SIGNAL FROM A FORWARD LOOKING SENSOR TO ACTIVATE THE TRACTION CONTROL VALVE ...

Real-Time Dynamic Brake Assessment Proof of Concept Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lascurain, Mary Beth; Franzese, Oscar; Capps, Gary J

This proof-of-concept research was performed to explore the feasibility of using real-world braking data from commercial motor vehicles to make a diagnosis of brake condition similar to that of the performance-based brake tester (PBBT). This was done by determining the relationship between pressure and brake force (P-BF), compensating for the gross vehicle weight (GVW). The nature of this P-BF relationship (e.g., low braking force for a given brake application pressure) may indicate brake system problems. In order to determine the relationship between brake force and brake application pressure, a few key parameters of duty cycle information were collected. Because brakingmore » events are often brief, spanning only a few seconds, a sample rate of 10 Hz was needed. The algorithm under development required brake application pressure and speed (from which deceleration was calculated). Accurate weight estimation was also needed to properly derive the braking force from the deceleration. In order to ensure that braking force was the predominant factor in deceleration for the segments of data used in analysis, the data was screened for grade as well. Also, the analysis needed to be based on pressures above the crack pressure. The crack pressure is the pressure below which the individual brakes are not applied due the nature of the mechanical system. This value, which may vary somewhat from one wheel end to another, is approximately 10 psi. Therefore, only pressures 15 psi and above were used in the analysis. The Department of Energy s Medium Truck Duty Cycle research has indicated that under the real-world circumstances of the test vehicle brake pressures of up to approximately 30 psi can be expected. Several different types of data were collected during the testing task of this project. Constant-pressure stopping tests were conducted at several combinations of brake application pressure (15, 20, 25, and 30 psi), load conditions (moderately and fully laden), and speeds (20 and 30 mph). Data was collected at 10 Hz. Standard and stepped-pressure performance-based brake tests with brake pressure transducers were performed for each loading condition. The stepped-pressure test included the constant-pressure intervals of brake application at 15, 20, 25, and 30 psi. The PBBT data files included 10 Hz streaming data collected during the testing of each axle. Two weeks of real-world duty cycle (driving and braking) data was also collected at 10 Hz. Initial analysis of the data revealed that the data collected in the field (i.e., day-to-day operations) provided the same information as that obtained from the controlled tests. Analysis of the data collected revealed a strong linear relationship between brake application pressure and deceleration for given GVWs. As anticipated, initial speed was not found to be a significant factor in the deceleration-pressure relationship, unlike GVW. The positive results obtained from this proof of concept test point to the need for further research to expand this concept. A second phase should include testing over a wider range of speeds and include medium brake application pressures in addition to the low pressures tested in this research. Testing on multiple vehicles would also be of value. This future phase should involve testing to determine how degradation of braking performance affects the pressure-deceleration relationship.« less

KSC-04PD-1088

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. -- A Rudder Speed Brake Actuator is being removed from the orbiter Atlantis for shipment to the vendor for inspection. An actuator is a motor that moves the tail rudder back and forth to help steer it during landing and brake its speed. The vertical tail consists of a structural fin surface made of aluminum, the Rudder Speed Brake surface, a tip and a lower trailing edge. The rudder splits into two halves to serve as a speed brake. The vertical tail and Rudder Speed Brake are covered with a reusable thermal protection system. Atlantis is undergoing maintenance and inspection in the Orbiter Processing Facility for a future mission.

KSC-04PD-1089

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. -- A Rudder Speed Brake Actuator is being removed from the orbiter Atlantis for shipment to the vendor for inspection. An actuator is a motor that moves the tail rudder back and forth to help steer it during landing and brake its speed. The vertical tail consists of a structural fin surface made of aluminum, the Rudder Speed Brake surface, a tip and a lower trailing edge. The rudder splits into two halves to serve as a speed brake. The vertical tail and Rudder Speed Brake are covered with a reusable thermal protection system. Atlantis is undergoing maintenance and inspection in the Orbiter Processing Facility for a future mission.

Distributed and self-adaptive vehicle speed estimation in the composite braking case for four-wheel drive hybrid electric car

NASA Astrophysics Data System (ADS)

Zhao, Z.-G.; Zhou, L.-J.; Zhang, J.-T.; Zhu, Q.; Hedrick, J.-K.

2017-05-01

Considering the controllability and observability of the braking torques of the hub motor, Integrated Starter Generator (ISG), and hydraulic brake for four-wheel drive (4WD) hybrid electric cars, a distributed and self-adaptive vehicle speed estimation algorithm for different braking situations has been proposed by fully utilising the Electronic Stability Program (ESP) sensor signals and multiple powersource signals. Firstly, the simulation platform of a 4WD hybrid electric car was established, which integrates an electronic-hydraulic composited braking system model and its control strategy, a nonlinear seven degrees-of-freedom vehicle dynamics model, and the Burckhardt tyre model. Secondly, combining the braking torque signals with the ESP signals, self-adaptive unscented Kalman sub-filter and main-filter adaptable to the observation noise were, respectively, designed. Thirdly, the fusion rules for the sub-filters and master filter were proposed herein, and the estimation results were compared with the simulated value of a real vehicle speed. Finally, based on the hardware in-the-loop platform and by picking up the regenerative motor torque signals and wheel cylinder pressure signals, the proposed speed estimation algorithm was tested under the case of moderate braking on the highly adhesive road, and the case of Antilock Braking System (ABS) action on the slippery road, as well as the case of ABS action on the icy road. Test results show that the presented vehicle speed estimation algorithm has not only a high precision but also a strong adaptability in the composite braking case.

49 CFR 232.603 - Design, interoperability, and configuration management requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

...: 1999; Revised 2002, 2007); (3) AAR S-4220, “ECP Cable-Based Brake DC Power Supply—Performance...; Revised: 2004); (7) AAR S-4260, “ECP Brake and Wire Distributed Power Interoperability Test Procedures...) Approval. A freight train or freight car equipped with an ECP brake system and equipment covered by the AAR...

49 CFR 238.5 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... parts at the ends of adjoining vehicles in a train that are designed to engage when subjected to large... designed retarding force on the train. A brake is not effective if its piston travel is in excess of the... next midnight on a given date. Class I brake test means a complete passenger train brake system test...

49 CFR 238.5 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... that are designed to engage when subjected to large buff loads to prevent the override of one vehicle... designed retarding force on the train. A brake is not effective if its piston travel is in excess of the... next midnight on a given date. Class I brake test means a complete passenger train brake system test...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

Detection of braking intention in diverse situations during simulated driving based on EEG feature combination

NASA Astrophysics Data System (ADS)

Kim, Il-Hwa; Kim, Jeong-Woo; Haufe, Stefan; Lee, Seong-Whan

2015-02-01

Objective. We developed a simulated driving environment for studying neural correlates of emergency braking in diversified driving situations. We further investigated to what extent these neural correlates can be used to detect a participant's braking intention prior to the behavioral response. Approach. We measured electroencephalographic (EEG) and electromyographic signals during simulated driving. Fifteen participants drove a virtual vehicle and were exposed to several kinds of traffic situations in a simulator system, while EEG signals were measured. After that, we extracted characteristic features to categorize whether the driver intended to brake or not. Main results. Our system shows excellent detection performance in a broad range of possible emergency situations. In particular, we were able to distinguish three different kinds of emergency situations (sudden stop of a preceding vehicle, sudden cutting-in of a vehicle from the side and unexpected appearance of a pedestrian) from non-emergency (soft) braking situations, as well as from situations in which no braking was required, but the sensory stimulation was similar to stimulations inducing an emergency situation (e.g., the sudden stop of a vehicle on a neighboring lane). Significance. We proposed a novel feature combination comprising movement-related potentials such as the readiness potential, event-related desynchronization features besides the event-related potentials (ERP) features used in a previous study. The performance of predicting braking intention based on our proposed feature combination was superior compared to using only ERP features. Our study suggests that emergency situations are characterized by specific neural patterns of sensory perception and processing, as well as motor preparation and execution, which can be utilized by neurotechnology based braking assistance systems.

49 CFR 232.105 - General requirements for locomotives.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION BRAKE SYSTEM SAFETY STANDARDS FOR FREIGHT AND OTHER NON-PASSENGER... reservoir on locomotives and related piping shall be zero, unless the system is capable of maintaining the... equalizing-reservoir leakage can be corrected. On locomotives equipped with electronic brakes, if the system...

75 FR 51521 - Federal Motor Vehicle Safety Standards; Air Brake Systems; Technical Report on the Effectiveness...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-20

... of Antilock Braking Systems in Heavy Truck Tractors and Trailers AGENCY: National Highway Traffic...] in Heavy Truck Tractors and Trailers. DATES: Comments must be received no later than December 20...

75 FR 67634 - Parts and Accessories Necessary for Safe Operation: Antilock Brake Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-03

... trailer with an antilock brake system be equipped with an external malfunction indicator lamp. DATES: This... malfunction indicator lamp. FMCSA used the Agency's direct final rule procedures (75 FR 29915, May 28, 2010...

Baseline tests of the EVA contractor electric passenger vehicle

NASA Technical Reports Server (NTRS)

Bozek, J. M.; Tryon, H. B.; Slavick, R. J.

1977-01-01

The EVA Contactor four door sedan, an electric passenger vehicle, was tested to characterize the state-of-the-art of electric vehicles. It is a four passenger sedan that was converted to an electric vehicle. It is powered by 16 series connected 6 volt electric vehicle batteries through a four step contactor controller actuated by a foot accelerator pedal. The controller changes the voltage applied to the separately excited DC motor. The braking system is a vacuum assisted hydraulic braking system. Regenerative braking was also provided.

Electrostatic and tribological phenomena and their effect on the braking torque in the shaft-oil-lip seal system

NASA Astrophysics Data System (ADS)

Gajewski, Juliusz B.; Glogowski, Marek J.

2008-12-01

The former research [1] was carried out on the influence of tribocharging in a system: metal rotating shaft-oil-lip seal on its work, especially on changes in the shaft braking torque with the increasing angular shaft velocity and oil temperature. The results obtained suggested that there be a possibility of reducing the braking torque by an external electric field. The compensation for the electric field generated in the system by natural tribocharging was proposed. The reduction in the braking torque seemed possible while applying an external DC electric field to the system. In general, the torque tended to increase with the increasing DC electric field for a variety of the oils and lip seals used and for different shaft angular velocities (rotational speeds) and oil temperatures. The braking torque reduction was achieved only for one lip seal and some different oils, which was and is a promising, expected result. The research results were yet presented elsewhere [1-3] and here some novel attempt has been made to interpret the results obtained in their physical—tribological and especially electrostatic—aspects since there has been a lack of such an interpretation in the literature of the subject.

An Analytical Design Method for a Regenerative Braking Control System for DC-electrified Railway Systems under Light Load Conditions

NASA Astrophysics Data System (ADS)

Saito, Tatsuhito; Kondo, Keiichiro; Koseki, Takafumi

A DC-electrified railway system that is fed by diode rectifiers at a substation is unable to return the electric power to an AC grid. Accordingly, the braking cars have to restrict regenerative braking power when the power consumption of the powering cars is not sufficient. However, the characteristics of a DC-electrified railway system, including the powering cars, is not known, and a mathematical model for designing a controller has not been established yet. Hence, the object of this study is to obtain the mathematical model for an analytical design method of the regenerative braking control system. In the first part of this paper, the static characteristics of this system are presented to show the position of the equilibrium point. The linearization of this system at the equilibrium point is then performed to describe the dynamic characteristics of the system. An analytical design method is then proposed on the basis of these characteristics. The proposed design method is verified by experimental tests with a 1kW class miniature model, and numerical simulations.

Advanced propulsion system for hybrid vehicles

NASA Technical Reports Server (NTRS)

Norrup, L. V.; Lintz, A. T.

1980-01-01

A number of hybrid propulsion systems were evaluated for application in several different vehicle sizes. A conceptual design was prepared for the most promising configuration. Various system configurations were parametrically evaluated and compared, design tradeoffs performed, and a conceptual design produced. Fifteen vehicle/propulsion systems concepts were parametrically evaluated to select two systems and one vehicle for detailed design tradeoff studies. A single hybrid propulsion system concept and vehicle (five passenger family sedan)were selected for optimization based on the results of the tradeoff studies. The final propulsion system consists of a 65 kW spark-ignition heat engine, a mechanical continuously variable traction transmission, a 20 kW permanent magnet axial-gap traction motor, a variable frequency inverter, a 386 kg lead-acid improved state-of-the-art battery, and a transaxle. The system was configured with a parallel power path between the heat engine and battery. It has two automatic operational modes: electric mode and heat engine mode. Power is always shared between the heat engine and battery during acceleration periods. In both modes, regenerative braking energy is absorbed by the battery.

Braking Distance of Hoist Conveyances Required for Safe Stopping Under the Conditions of Emergency Braking

NASA Astrophysics Data System (ADS)

Wolny, Stanisław

2017-06-01

This study investigates selected aspects of the dynamic behaviour of mine hoists during the emergency braking in an event of overtravel. Characteristics of the braking force that needs to be applied in the headgear and in the pit bottom to arrest the conveyance in the event of an overtravel are derived from laboratory and industrial test data and recalling the results reported in literature. The real hoist installation is replaced by a model whereby the equations of motion of rope elements are written as for elastic strings, taking into account the variable length of the hoisting rope section between the Koepe pulley and the conveyance being arrested in the head tower. Analytical formulas are provided whereby the displacement of the top conveyance with the payload for the constant elasticity coefficient of the hoisting rope section between the conveyance being arrested in the head tower and the Koepe pulley is expressed as the function of the braking force and of the operational parameters of the hoist gear. The hoist operation is investigated in the event of emergency braking, taking into account the two aspects of the cycle: - the time required for the conveyance to be stopped, - the distance travelled by the conveyance until it is stopped. The results of the dynamic analysis of the hoist installation in the conditions of emergency braking may be utilised in selection of the effective and adequate braking system guaranteeing the safety of the system operation.

Wheel slip control with torque blending using linear and nonlinear model predictive control

NASA Astrophysics Data System (ADS)

Basrah, M. Sofian; Siampis, Efstathios; Velenis, Efstathios; Cao, Dongpu; Longo, Stefano

2017-11-01

Modern hybrid electric vehicles employ electric braking to recuperate energy during deceleration. However, currently anti-lock braking system (ABS) functionality is delivered solely by friction brakes. Hence regenerative braking is typically deactivated at a low deceleration threshold in case high slip develops at the wheels and ABS activation is required. If blending of friction and electric braking can be achieved during ABS events, there would be no need to impose conservative thresholds for deactivation of regenerative braking and the recuperation capacity of the vehicle would increase significantly. In addition, electric actuators are typically significantly faster responding and would deliver better control of wheel slip than friction brakes. In this work we present a control strategy for ABS on a fully electric vehicle with each wheel independently driven by an electric machine and friction brake independently applied at each wheel. In particular we develop linear and nonlinear model predictive control strategies for optimal performance and enforcement of critical control and state constraints. The capability for real-time implementation of these controllers is assessed and their performance is validated in high fidelity simulation.

78 FR 13755 - Notice of Receipt of Petition for Decision That Nonconforming 2003 Jeep Wrangler Multi-Purpose...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-28

... System, 114 Theft Protection, 116 Motor Vehicle Brake Fluids, 118 Power-Operated Window, Partition, and...: Replacement of the instrument cluster with a U.S.-model component with inscription of the word ``brake'' on the brake failure warning light as well as reading speed in mph. Standard No. 108 Lamps, Reflective...

75 FR 71530 - Airworthiness Directives; DASSAULT AVIATION Model MYSTERE-FALCON 50 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-24

... because this unsafe condition could result in a high speed runway excursion when the brakes are applied... pipes of the emergency brake system 2 located near the nose landing gear bearing were swapped. The swapping of these two pipes implies that when the Left Hand (LH) brake pedal is depressed, the Right Hand...

Augmented Cognition - Phase 4 Cognitive Assessment and Task Management (CAT-M)

DTIC Science & Technology

2008-12-01

Angle Brake Pedal Force Accelerator Pedal ...Wheel Angle • Brake Pedal Force • Accelerator Pedal Deflection Note that we are using the controls as input to the prediction system. This means... Angle . At time >2.5 seconds, the Accelerator Pedal and Brake Pedal become statistically significantly easier to predict than Steering Wheel Angle .

49 CFR 238.445 - Automated monitoring.

Code of Federal Regulations, 2010 CFR

2010-10-01

... performance of the following systems or components: (1) Reception of cab signals and train control signals; (2) Truck hunting; (3) Dynamic brake status; (4) Friction brake status; (5) Fire detection systems; (6) Head end power status; (7) Alerter or deadman control; (8) Horn and bell; (9) Wheel slide; (10) Tilt system...

Safety of advanced braking concepts for high speed ground transportation systems

DOT National Transportation Integrated Search

1995-09-01

The objective of this study is to develop qualitative and quantitative information on the various braking strategies used in high-speed ground transportation systems in support of the Federal Railroad Administration (FRA). The apporach employed in th...

Machine & electrical double control air dryer for vehicle air braking system

NASA Astrophysics Data System (ADS)

Zhang, Xuan; Yang, Liu; Wang, Xian Yan; Tan, Xiao Yan; Wang, Wei

2017-09-01

As is known to all, a vehicle air brake system, in which usually contains moisture. To solve the problem, it is common to use air dryer to dry compressed air effectively and completely remove the moisture and oil of braking system. However, the existing air dryer is not suitable for all commercial vehicles. According to the operational status of the new energy vehicles in the initial operating period, the structure design principle of the machine & electric control air dryer is expounded from the aspects of the structure and operating principle, research & development process.

Autonomous collision avoidance system by combined control of steering and braking using geometrically optimised vehicular trajectory

NASA Astrophysics Data System (ADS)

Hayashi, Ryuzo; Isogai, Juzo; Raksincharoensak, Pongsathorn; Nagai, Masao

2012-01-01

This study proposes an autonomous obstacle avoidance system not only by braking but also by steering, as one of the active safety technologies to prevent traffic accidents. The proposed system prevents the vehicle from colliding with a moving obstacle like a pedestrian jumping out from the roadside. In the proposed system, to avoid the predicted colliding position based on constant-velocity obstacle motion assumption, the avoidance trajectory is derived as connected two identical arcs. The system then controls the vehicle autonomously by the combined control of the braking and steering systems. In this paper, the proposed system is examined by real car experiments and its effectiveness is shown from the results of the experiments.

KSC-04PD-1091

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. -- Workers attach a crane to one of the Rudder Speed Brake Actuators that are being removed from the orbiter Atlantis for shipment to the vendor for inspection. An actuator is a motor that moves the tail rudder back and forth to help steer it during landing and brake its speed. The vertical tail consists of a structural fin surface made of aluminum, the Rudder Speed Brake surface, a tip and a lower trailing edge. The rudder splits into two halves to serve as a speed brake. The vertical tail and Rudder Speed Brake are covered with a reusable thermal protection system. Atlantis is undergoing maintenance and inspection in the Orbiter Processing Facility for a future mission.

KSC-04PD-1092

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. -- Workers attach a crane to one of the Rudder Speed Brake Actuators that are being removed from the orbiter Atlantis for shipment to the vendor for inspection. An actuator is a motor that moves the tail rudder back and forth to help steer it during landing and brake its speed. The vertical tail consists of a structural fin surface made of aluminum, the Rudder Speed Brake surface, a tip and a lower trailing edge. The rudder splits into two halves to serve as a speed brake. The vertical tail and Rudder Speed Brake are covered with a reusable thermal protection system. Atlantis is undergoing maintenance and inspection in the Orbiter Processing Facility for a future mission.

KSC-04PD-1094

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. -- Workers ensure the safe removal of a Rudder Speed Brake Actuator from the orbiter Atlantis. This and three other actuators are being shipped to the vendor for inspection. An actuator is a motor that moves the tail rudder back and forth to help steer it during landing and brake its speed. The vertical tail consists of a structural fin surface made of aluminum, the Rudder Speed Brake surface, a tip and a lower trailing edge. The rudder splits into two halves to serve as a speed brake. The vertical tail and Rudder Speed Brake are covered with a reusable thermal protection system. Atlantis is undergoing maintenance and inspection in the Orbiter Processing Facility for a future mission.

KSC-04PD-1090

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. -- This is a closeup of one of the Rudder Speed Brake Actuators that are being removed from the orbiter Atlantis for shipment to the vendor for inspection. An actuator is a motor that moves the tail rudder back and forth to help steer it during landing and brake its speed. The vertical tail consists of a structural fin surface made of aluminum, the Rudder Speed Brake surface, a tip and a lower trailing edge. The rudder splits into two halves to serve as a speed brake. The vertical tail and Rudder Speed Brake are covered with a reusable thermal protection system. Atlantis is undergoing maintenance and inspection in the Orbiter Processing Facility for a future mission.

Design Considerations and Experimental Verification of a Rail Brake Armature Based on Linear Induction Motor Technology

NASA Astrophysics Data System (ADS)

Sakamoto, Yasuaki; Kashiwagi, Takayuki; Hasegawa, Hitoshi; Sasakawa, Takashi; Fujii, Nobuo

This paper describes the design considerations and experimental verification of an LIM rail brake armature. In order to generate power and maximize the braking force density despite the limited area between the armature and the rail and the limited space available for installation, we studied a design method that is suitable for designing an LIM rail brake armature; we considered adoption of a ring winding structure. To examine the validity of the proposed design method, we developed a prototype ring winding armature for the rail brakes and examined its electromagnetic characteristics in a dynamic test system with roller rigs. By repeating various tests, we confirmed that unnecessary magnetic field components, which were expected to be present under high speed running condition or when a ring winding armature was used, were not present. Further, the necessary magnetic field component and braking force attained the desired values. These studies have helped us to develop a basic design method that is suitable for designing the LIM rail brake armatures.

Payout tension control system for reel mounted cable

NASA Astrophysics Data System (ADS)

Winkler, Gerhard B.

1992-06-01

A payout control arm is angularly displaceable about a brake shaft during payout of a cable from a storage reel in response to tensioning forces transmitted through the cable from a payout load with the cable being entrained about a pulley rotatably carried on the control arm in spaced relation to the brake shaft. Gearing drivingly connects the pulley to the brake shaft to stop payout and cause the cable to frictionally grip the pulley in response to brake engagement thereby preventing continued transmittal of tensioning forces to the reel.

Limited Investigation into Regenerative Braking and Energy Storage for Mass Transit Systems

DOT National Transportation Integrated Search

1978-03-01

This study examines the technical and economic aspects of a regenerative braking/flywheel energy storage subway system. In order to define the analytical models accurately, it was necessary to gather data on the trains, rail network, schedules, and a...

An Analysis of the Crash Experience of Vehicles Equipped with Antilock Braking System

DOT National Transportation Integrated Search

1995-06-01

National Center for Statistics and Analysis has recently completed an initial : analysis of the crash experience of passenger cars (PCs) and light trucks and : vans (LTVs) equipped with antilock braking systems (ABS). Four types of crashes : were ide...