Science.gov

Sample records for auxiliary charcoal bed

  1. Summary of ACSL Simulations of the MSRE Auxiliary Charcoal Bed Vacuum System

    SciTech Connect

    Damiano, B

    2000-10-26

    The simulation of the Auxiliary Charcoal Bed (ACB) Vacuum System was performed to evaluate the original vacuum system design, detect and identify design deficiencies, investigate the effects of proposed corrections on system performance, and generally aid in refining the system design before construction and mockup testing. The simulation was performed by using the Advanced Continuous Simulation Language (ACSL). The vacuum system design goals are to provide approximately 20 SCFM of both booster gas and purge gas through the system and maintain a flow of approximately 40 SCFM with a velocity of 50 to 75 f/sec at the entrance to the cyclone separator. The model results showed that the original system design was incapable of meeting the system performance goals. Further simulations showed that the following modifications to the original vacuum system design were required to make the system performance acceptable; (1) Remove valve PCV4. (2) Modify the flow controllers FTC3 and FTC4 from the original flow range of 0-17.6 SCFM (0-500 SLM) to 0-35.3 SCFM (0-1000 SLM). (3) Replace the bellows sealed valves SV-1, SV-3A, SV-3B, SV-4A, and SV-4B with less restrictive ball valves. The simulation results saved considerable time and effort by identifying flaws in the original system design. Early identification of these flaws and the use of the simulation model to investigate possible solutions allowed corrective modifications to be made before construction of the mock up test facility.

  2. Measurement of the axial distribution of radioactivity in the auxiliary charcoal bed of the Molten Salt Reactor Experiment at ORNL

    SciTech Connect

    Miller, L.F.; Buckner, M.; Buchanan, M.

    1999-07-01

    The Molten Salt Reactor Experiment (MSRE) at Oak Ridge National Laboratory commenced operation in 1964 and was shut down in 1969. It was fueled with {sup 233}UF{sub 4} in a carrier salt of LiF-BeF{sub 2}-ZrF{sub 4}, and it operated at 1,200 F. After it was shut down, the fuel was heated annually to 200 C to recombine fluorine (with the fuel) released due to radiation-induced reactions in the fuel salt. However, a competing reaction oxidized uranium to UF{sub 6}, which was released (along with F{sub 2}) from the fuel and trapped in one of four charcoal filters in the auxiliary charcoal bed (ACB). One of the tasks for decommissioning of the MSRE requires that at least 90% of the estimated 3 kg of {sup 233}U, and radioactive decay products, in this filter be removed, and one of the proposed methods is to vacuum the charcoal above a specified axial position in the filter. This requires that the axial distribution of activity in the filter be measured in a 60 rad/h radiation field to determine where this penetration can be made. To accomplish this, the shielded detector with a pinhole collimator, and with a laser positioning capability, was remotely translated to various axial positions to accomplish these measurements. Activities in the steel screen, and various regions of the charcoal bed, are estimated, and uncertainties in these estimates are generally {lt}1%. Results from this analysis are used for continued operational decisions for decommissioning of the MSRE.

  3. Use of Activated Charcoal for {sup 220}Rn Adsorption for Operations Associated with the Uranium Deposit in the Auxiliary Charcoal Bed at the Molten Salt Reactor Experiment Facility

    SciTech Connect

    Coleman, R.L.

    1999-03-01

    Measurements have been collected with the purpose of evaluating the effectiveness of activated charcoal for the removal of {sup 220}Rn from process off-gas at the Molten Salt Reactor Experiment (MSRE) at Oak Ridge National Laboratory. A series of bench-scale tests were performed at superficial flow velocities of 10, 18, 24, and 33 cm/s (20, 35, 47, and 65 ft/min) with a continuous input concentration of {sup 220}Rn in the range of 9 x 10{sup 3} pCi/L. In addition, two tests were performed at the MSRE facility by flowing helium through the auxiliary charcoal bed uranium deposit. These tests were performed so that the adsorptive effectiveness could be evaluated with a relatively high concentration of {sup 220}Rn. In addition to measuring the effectiveness of activated charcoal as a {sup 220}Rn adsorption media, the source term for available {sup 220}Rn in the deposit is actually available for removal and that the relative activity of fission gases is very small when compared to {sup 220}Rn. The measurement data were then used to evaluate the expected effectiveness of a proposed charcoal adsorption bed consisting of a right circular cylinder having a diameter of 43 cm and a length of 91 cm (17 in. I.D. x 3 ft.). The majority of the measurement data predicts an overall 220Rn activity reduction factor of about 1 x 10{sup 9} for such a design; however, two measurements collected at a flow velocity of 18 cm/s (35 ft/min) indicated that the reduction factor could be as low as 1 x 10{sup 6}. The adsorptive capacity of the proposed trap was also evaluated to determine the expected life prior to degradation of performance. Taking a conservative vantage point during analysis, it was estimated that the adsorption effectiveness should not begin to deteriorate until a {sup 220}Rn activity on the order of 10{sup 10} Ci has been processed. It was therefore concluded that degradation of performance would likely occur as the result of causes other than filling by radon progeny.

  4. Use of Activated Charcoal for Rn-220 Adsorption for Operations Associated with the Uranium Deposit in the Auxiliary Charcoal Bed at the Molten Salt Reactor Experiment Facility

    SciTech Connect

    Coleman, R.L.

    1999-03-17

    Measurements have been collected with the purpose of evaluating the effectiveness of activated charcoal for the removal of {sup 220}Rn from process off-gas at the Molten Salt Reactor Experiment (MSRE) at Oak Ridge National Laboratory. A series of bench-scale tests were performed at superficial flow velocities of 10, 18, 24, and 33 cm s{sup -1} (20, 35, 47, and 65 ft min{sup -1}) with a continuous input concentration of {sup 220}Rn in the range of 9 x 10{sup 3} pCi L{sup -1}. In addition, two tests were performed at the MSRE facility by flowing helium through the auxiliary charcoal bed uranium deposit. These tests were performed so that the adsorptive effectiveness could be evaluated with a relatively high concentration of {sup 220}Rn. In addition to measuring the effectiveness of activated charcoal as a {sup 220}Rn adsorption media, the source term for available {sup 220}Rn and gaseous fission products was evaluated and compared to what is believed to be present in the deposit. The results indicate that only a few percent of the total {sup 220}Rn in the deposit is actually available for removal and that the relative activity of fission gases is very small when compared to {sup 220}Rn. The measurement data were then used to evaluate the expected effectiveness of a proposed charcoal adsorption bed consisting of a right circular cylinder having a diameter of 43 cm and a length of 91 cm (17 in. I.D. x 3 ft.). The majority of the measurement data predicts an overall {sup 220}Rn activity reduction factor of about 1 x 10{sup 9} for such a design; however, two measurements collected at a flow velocity of 18 cm s{sup -1} (35 ft min{sup -1}) indicated that the reduction factor could be as low as 1 x 10{sup 6}. The adsorptive capacity of the proposed trap was also evaluated to determine the expected life prior to degradation of performance. Taking a conservative vantage point during analysis, it was estimated that the adsorption effectiveness should not begin to deteriorate

  5. In Situ NDA Conformation Measurements Performed at Auxiliary Charcoal Bed and Other Main Charcoal Beds After Uranium Removal from Molten Salt Reactor Experiment ACB at Oak Ridge National Laboratory

    SciTech Connect

    Haghighi, M. H.; Kring, C. T.; McGehee, J. T.; Jugan, M. R.; Chapman, J.; Meyer, K. E.

    2002-02-26

    The Molten Salt Reactor Experiment (MSRE) site is located in Tennessee, on the U.S. Department of Energy (DOE) Oak Ridge Reservation (ORR). The MSRE was run by Oak Ridge National Laboratory (ORNL) to demonstrate the desirable features of the molten-salt concept in a practical reactor that could be operated safely and reliably. It introduced the idea of a homogeneous reactor using fuel salt media and graphite moderation for power and breeder reactors. The MSRE reactor and associated components are located in cells beneath the floor in the high-bay area of Building 7503. The reactor was operated from June 1965 to December 1969. When the reactor was shut down, fuel salt was drained from the reactor circuit to two drain tanks. A ''clean'' salt was then circulated through the reactor as a decontamination measure and drained to a third drain tank. When operations ceased, the fuel and flush salts were allowed to cool and solidify in the drain tanks. At shutdown, the MSRE facility complex was placed in a surveillance and maintenance program. Beginning in 1987, it was discovered that gaseous uranium (U-233/U-232) hexafluoride (UF6) had moved throughout the MSRE process systems. The UF6 had been generated when radiolysis in the fluorine salts caused the individual constituents to dissociate to their component atoms, including free fluorine. Some of the free fluorine combined with uranium fluorides (UF4) in the salt to produce UF6. UF6 is gaseous at slightly above ambient temperatures; thus, periodic heating of the fuel salts (which was intended to remedy the radiolysis problems) and simple diffusion had allowed the UF6 to move out of the salt and into the process systems of MSRE. One of the systems that UF6 migrated into due to this process was the offgas system which is vented to the MSRE main charcoal beds and MSRE auxiliary charcoal bed (ACB). Recently, the majority of the uranium laden-charcoal material residing within the ACB was safely and successfully removed using

  6. Fluidized bed charcoal particle production system

    SciTech Connect

    Sowards, N.K.

    1985-04-09

    A fluidized bed charcoal particle production system, including apparatus and method, wherein pieces of combustible waste, such as sawdust, fragments of wood, etc., are continuously disposed within a fluidized bed of a pyrolytic vessel. Preferably, the fluidized bed is caused to reach operating temperatures by use of an external pre-heater. The fluidized bed is situated above an air delivery system at the bottom of the vessel, which supports pyrolysis within the fluidized bed. Charcoal particles are thus formed within the bed from the combustible waste and are lifted from the bed and placed in suspension above the bed by forced air passing upwardly through the bed. The suspended charcoal particles and the gaseous medium in which the particles are suspended are displaced from the vessel into a cyclone mechanism where the charcoal particles are separated. The separated charcoal particles are quenched with water to terminate all further charcoal oxidation. The remaining off-gas is burned and, preferably, the heat therefrom used to generate steam, kiln dry lumber, etc. Preferably, the bed material is continuously recirculated and purified by removing tramp material.

  7. Time-dependent response of a charcoal bed to radon and water vapor in flowing air

    SciTech Connect

    Henkel, J.A.; Fentiman, A.W.; Blue, T.E.

    1995-12-31

    Extremely high airborne concentrations of radon gas may be encountered during the remediation of uranium mill tailings storage facilities. Radon is also a constituent of the off-gas of mill-tailing vitrification. An effective way to remove radon from either gas is to pass the gas through a packed bed containing activated charcoal. Measurements of radon concentrations in the environment using charcoal canisters were first described by George. Canisters similar to those used by George in his first experiments have become the U.S. Environmental Protection Agency`s (EPA`s) standard for measuring environmental radon and were described in the EPA protocol for environmental radon measurement. The dynamic behavior of EPA charcoal canisters has been previously described with a mathematical model for the kinetics of radon gas adsorption in air in the presence of water vapor. This model for charcoal canisters has been extended to large charcoal beds with flowing air containing radon and water vapor. The mathematical model for large charcoal beds can be used to evaluate proposed bed designs or to model existing beds. Parameters that affect the radon distribution within a charcoal bed that can be studied using the mathematical model include carrier gas relative humidity and flow velocity, and input radon concentration. In addition, the relative performances of several different charcoals can be studied, provided sufficient information about their adsorption, desorption, and diffusion constants is known.

  8. Air gasification of rice husk in bubbling fluidized bed reactor with bed heating by conventional charcoal.

    PubMed

    Makwana, J P; Joshi, Asim Kumar; Athawale, Gaurav; Singh, Dharminder; Mohanty, Pravakar

    2015-02-01

    An experimental study of air gasification of rice husk was conducted in a bench-scale fluidized bed gasifier (FBG) having 210 mm diameter and 1600 mm height. Heating of sand bed material was performed using conventional charcoal fuel. Different operating conditions like bed temperature, feeding rate and equivalence ratio (ER) varied in the range of 750-850 °C, 25-31.3 kg/h, and 0.3-0.38, respectively. Flow rate of air was kept constant (37 m(3)/h) during FBG experiments. The carbon conversion efficiencies (CCE), cold gas efficiency, and thermal efficiency were evaluated, where maximum CCE was found as 91%. By increasing ER, the carbon conversion efficiency was decreased. Drastic reduction in electric consumption for initial heating of gasifier bed with charcoal compared to ceramic heater was ∼45%. Hence rice husk is found as a potential candidate to use directly (without any processing) in FBG as an alternative renewable energy source from agricultural field. PMID:25446789

  9. Air gasification of rice husk in bubbling fluidized bed reactor with bed heating by conventional charcoal.

    PubMed

    Makwana, J P; Joshi, Asim Kumar; Athawale, Gaurav; Singh, Dharminder; Mohanty, Pravakar

    2015-02-01

    An experimental study of air gasification of rice husk was conducted in a bench-scale fluidized bed gasifier (FBG) having 210 mm diameter and 1600 mm height. Heating of sand bed material was performed using conventional charcoal fuel. Different operating conditions like bed temperature, feeding rate and equivalence ratio (ER) varied in the range of 750-850 °C, 25-31.3 kg/h, and 0.3-0.38, respectively. Flow rate of air was kept constant (37 m(3)/h) during FBG experiments. The carbon conversion efficiencies (CCE), cold gas efficiency, and thermal efficiency were evaluated, where maximum CCE was found as 91%. By increasing ER, the carbon conversion efficiency was decreased. Drastic reduction in electric consumption for initial heating of gasifier bed with charcoal compared to ceramic heater was ∼45%. Hence rice husk is found as a potential candidate to use directly (without any processing) in FBG as an alternative renewable energy source from agricultural field.

  10. Investigation on fixed bed column performance of fluoride adsorption by sugarcane charcoal.

    PubMed

    Mondal, N K; Bhaumik, R; Roy, P; Das, B; Datta, J K

    2013-11-01

    The present study explores the potentiality of sugarcane charcoal for fluoride removal from synthetic fluoride solution. Column adsorption experiments with respect to variation of flow rate, pH, initial concentration, and column depths were carried out. Sugarcane charcoal exhibited almost consistent scavenging capacity at various bed depths with a flow rate 4.34 ml min(-1). Maximum adsorption capacity of sugarcane charcoal was recorded 7.33 mg g(-1). The adsorption studies were simulated using Thomas and Bed depth service time model. Both the models consistently predict its characteristic parameters and describe the breakthrough profiles in the whole range of sorption process.

  11. Charcoal bed operation for optimal organic carbon removal

    SciTech Connect

    Merritt, C.M.; Scala, F.R.

    1995-05-01

    Historically, evaporation, reverse osmosis or charcoal-demineralizer systems have been used to remove impurities in liquid radwaste processing systems. At Nine Mile point, we recently replaced our evaporators with charcoal-demineralizer systems to purify floor drain water. A comparison of the evaporator to the charcoal-demineralizer system has shown that the charcoal-demineralizer system is more effective in organic carbon removal. We also show the performance data of the Granulated Activated Charcoal (GAC) vessel as a mechanical filter. Actual data showing that frequent backflushing and controlled flow rates through the GAC vessel dramatically increases Total Organic Carbon (TOC) removal efficiency. GAC vessel dramatically increases Total Organic Carbon (TOC) removal efficiency. Recommendations are provided for operating the GAC vessel to ensure optimal performance.

  12. Steady-state response of a charcoal bed to radon in flowing air with water vapor

    SciTech Connect

    Blue, T.E.; Jarzemba, M.S.; Fentiman, A.W.

    1995-06-01

    Previously we have developed a mathematical model of radon adsorption in active air with water vapor on small U.S. Environmental Protection Agency charcoal canisters that are used for environmental measurements of radon. The purpose of this paper is to extend this mathematical model to describe the adsorption of radon by large charcoal beds with radon-laden air flowing through them. The resulting model equations are solved analytically to predict the steady-state adsorption of radon by such beds. 14 refs., 3 figs.

  13. Evaluation of fructooligosaccharides separation using a fixed-bed column packed with activated charcoal.

    PubMed

    Kuhn, Raquel Cristine; Mazutti, Marcio A; Albertini, Lilian Buoro; Filho, Francisco Maugeri

    2014-05-25

    Recent studies have shown that the chromatographic separation of mixtures of saccharides may be improved by making use of activated charcoal, a promising low cost material for the separation of sugars, including fructooligosaccharides. In this work, the development of a methodology to separate fructooligosaccharides from glucose, fructose and sucrose, using a fixed bed column packed with activated charcoal is proposed. The influence of temperature, eluant concentration and step gradients were evaluated to increase the separation efficiency and fructooligosaccharide purity. The final degree of fructooligosaccharide purification and separation efficiency were about 94% and 3.03 respectively, using ethanol gradient concentration ranging from 3.5% to 15% (v/v) at 40°C. The fixed bed column packed with the activated charcoal was shown to be a promising alternative for sugar separation, mainly those rich in fructooligosaccharides, leading to solutions of acceptable degrees of purification.

  14. Adsorption and desorption of noble gases on activated charcoal: II. sup 222 Rn studies in a monolayer and packed bed

    SciTech Connect

    Scarpitta, S.C.; Harley, N.H. )

    1990-10-01

    The adsorptive and desorptive characteristics of canisters containing a petroleum-based charcoal were investigated under controlled conditions of temperature, relative humidity, and Rn concentration. Charcoals exposed in a monolayer and packed bed during exposure intervals of 1-7 d demonstrate that Rn adsorption and desorption are dependent on bed depth and the amount of water adsorbed. Changes in the adsorptive and desorptive properties of the charcoal occurred near the break-point where the pores became occluded by water vapor that condenses in the entrance capillaries. Radon-222 adsorption is decreased by an order of magnitude as the amount of adsorbed water exceeds the break-point of the charcoal. The reduction in pore surface due to adsorbed water results in a marked increase in the rate of Rn loss from exposed canisters, accounting for reduced adsorption. The apparent desorption time-constant for a 2-cm bed of loose Witco 6 x 10 mesh charcoal containing 0.220-0.365 kg H{sub 2}O kg-1 is typically between 2-8 h. The apparent desorption time-constant for an equivalent packed bed containing a water vapor content of 0.026-0.060 kg H{sub 2}O kg-1, which is below the break-point of the charcoal, is about 15-30 h. Conventional charcoal canisters, if exposed in the fully-opened configuration, can achieve the break-point in less than 4 d at 70% humidity. The use of a diffusion barrier would allow for longer exposure times until the break-point of the charcoal is achieved.

  15. Adsorption and desorption of noble gases on activated charcoal: II. 222Rn studies in a monolayer and packed bed.

    PubMed

    Scarpitta, S C; Harley, N H

    1990-10-01

    The adsorptive and desorptive characteristics of canisters containing a petroleum-based charcoal were investigated under controlled conditions of temperature, relative humidity, and Rn concentration. Charcoals exposed in a monolayer and packed bed during exposure intervals of 1-7 d demonstrate that Rn adsorption and desorption are dependent on bed depth and the amount of water adsorbed. Changes in the adsorptive and desorptive properties of the charcoal occurred near the break-point where the pores became occluded by water vapor that condenses in the entrance capillaries. Radon-222 adsorption is decreased by an order of magnitude as the amount of adsorbed water exceeds the break-point of the charcoal. The reduction in pore surface due to adsorbed water results in a marked increase in the rate of Rn loss from exposed canisters, accounting for reduced adsorption. The apparent desorption time-constant for a 2-cm bed of loose Witco 6 x 10 mesh charcoal containing 0.220-0.365 kg H2O kg-1 is typically between 2-8 h. The apparent desorption time-constant for an equivalent packed bed containing a water vapor content of 0.026-0.060 kg H2O kg-1, which is below the break-point of the charcoal, is about 15-30 h. Conventional charcoal canisters, if exposed in the fully-opened configuration, can achieve the break-point in less than 4 d at 70% humidity. The use of a diffusion barrier would allow for longer exposure times until the break-point of the charcoal is achieved. PMID:2398008

  16. Design of a californium source-driven measurement system for accountability of material recovered from the Molten Salt Reactor Experiment charcoal bed

    SciTech Connect

    Bentzinger, D.L.; Perez, R.B.; Mattingly, J.K.; Valentine, T.E.; Mihalczo, J.T.

    1998-05-01

    The Molten Salt Reactor Experiment Facility (MSRE) operated from 1965 to 1969. The fuel was a molten salt that flowed through the reactor core which consisted of uranium tetrafluoride with molten lithium and beryllium salt used as the coolant. In 1968 the fuel was switched from {sup 235}U to {sup 233}U. The Molten Salt Reactor Experiment was canceled in 1969 at which time approximately 4800 kg of salt was transferred to the fuel drain tanks. There was about 36.3 kg of uranium, 675 grams of plutonium and various fission products present in the fuel salt. The salt was allowed to solidify in the fuel drain tanks. The salt was heated on a yearly basis to recombine the fluorine gas with the uranium salt mixture. In March 1994, a gas sample was taken from the off gas system that indicated {sup 233}U had migrated from the fuel drain tank system to the off gas system. It was found that approximately 2.6 kg of uranium had migrated to the Auxiliary Charcoal Bed (ACB). The ACB is located in the concrete-lined charcoal bed cell which is below ground level located outside the MSRE building. Therefore, there was a concern for the potential of a nuclear criticality accident, although water would have to leak into the chamber for a criticality accident to occur. Unstable carbon/fluorine compounds were also formed when the fluorine reacted with the charcoal in the charcoal bed. The purpose of the proposed measurement system was to perform an accountability measurement to determine the fissile mass of {sup 233}U in the primary vessel. The contents of the primary containment assembly will then be transferred to three smaller containers for long term storage. Calculations were performed using MCNP-DSP to determine the configuration of the measurement system. The information obtained from the time signatures can then be compared to the measurement data to determine the amount of {sup 233}U present in the primary containment assembly.

  17. Adsorption and desorption of noble gases on activated charcoal: I. 133Xe studies in a monolayer and packed bed.

    PubMed

    Scarpitta, S C; Harley, N H

    1990-10-01

    Detailed desorption studies using petroleum-based activated charcoals were conducted in monolayers and packed beds. Less extensive studies were conducted on several other types of charcoal. Kinetic studies, using 133Xe, demonstrated the existence of a micropore volume with entrance capillaries that together determined the response characteristics of charcoal to external concentration gradients of tracer gases. This new two-phase model, composed of micropores and entrance capillaries, describes the desorption dynamics of an adsorbed gas in the presence of water vapor. Condensed water vapor in the entrance capillaries of the charcoal reduced the effective pore radius and increased the diffusion half-time. Water could also adversely affect the integrating capability of the charcoal dramatically if the adsorbed water completely blocked the entrance capillaries. The amount of adsorbed water required to block the capillaries varied with the charcoal type and was termed here as the "break-point." The desorption parameters measured in this work can be used to design an improved passive Rn monitor to effectively integrate during a 3-7 d exposure period by eliminating the adverse effects of water vapor. The improved canister design would provide more accurate and reproducible measurements of indoor Rn concentrations than are currently available. PMID:2398007

  18. Some Investigations of the Reaction of Activated Charcoal with Fluorine and Uranium Hexafluoride

    SciTech Connect

    Del Cul, G.D.; Fiedor, J.N.; Simmons, D.W.; Toth, L.M.; Trowbridge, L.D.; Williams

    1998-09-01

    The Molten Salt Reactor Experiment (MSRE) at Oak Ridge National Laboratory has been shut down since 1969, when the fuel salt was drained from the core into two Hastelloy N drain tanks at the reactor site. Over time, fluorine (F{sub 2}) and uranium hexafluoride (UF{sub 6}) moved from the salt through the gas piping to a charcoal bed, where they reacted with the activated charcoal. Some of the immediate concerns related to the migration of F{sub 2} and UF{sub 6} to the charcoal bed were the possibility of explosive reactions between the charcoal and F{sub 2}, the existence of conditions that could induce a criticality accident, and the removal and recovery of the fissile uranium from the charcoal. This report addresses the reactions and reactivity of species produced by the reaction of fluorine and activated charcoal and between charcoal and F{sub 2}-UF{sub 6} gas mixtures in order to support remediation of the MSRE auxiliary charcoal bed (ACB) and the recovery of the fissile uranium. The chemical identity, stoichiometry, thermochemistry, and potential for explosive decomposition of the primary reaction product, fluorinated charcoal, was determined.

  19. Activated Charcoal

    MedlinePlus

    ... heat common charcoal in the presence of a gas that causes the charcoal to develop lots of ... charcoal is used to treat poisonings, reduce intestinal gas (flatulence), lower cholesterol levels, prevent hangover, and treat ...

  20. Passivation of fluorinated activated charcoal

    SciTech Connect

    Del Cul, G.D.; Trowbridge, L.D.; Simmons, D.W.; Williams, D.F.; Toth, L.M.

    1997-10-01

    The Molten Salt Reactor Experiment (MSRE), at the Oak Ridge National Laboratory has been shut down since 1969 when the fuel salt was drained from the core into two Hastelloy N tanks at the reactor site. In 1995, a multiyear project was launched to remediate the potentially hazardous conditions generated by the movement of fissile material and reactive gases from the storage tanks into the piping system and an auxiliary charcoal bed (ACB). The top 12 in. of the ACB is known by gamma scan and thermal analysis to contain about 2.6 kg U-233. According to the laboratory tests, a few feet of fluorinated charcoal are believed to extend beyond the uranium front. The remainder of the ACB should consist of unreacted charcoal. Fluorinated charcoal, when subjected to rapid heating, can decompose generating gaseous products. Under confined conditions, the sudden exothermic decomposition can produce high temperatures and pressures of near-explosive characteristics. Since it will be necessary to drill and tap the ACB to allow installation of piping and instrumentation for remediation and recovery activities, it is necessary to chemically convert the reactive fluorinated charcoal into a more stable material. Ammonia can be administered to the ACB as a volatile denaturing agent that results in the conversion of the C{sub x}F to carbon and ammonium fluoride, NH{sub 4}F. The charcoal laden with NH{sub 4}F can then be heated without risking any sudden decomposition. The only consequence of heating the treated material will be the volatilization of NH{sub 4}F as a mixture of NH{sub 3} and HF, which would primarily recombine as NH{sub 4}F on surfaces below 200 C. The planned scheme for the ACB denaturing is to flow diluted ammonia gas in steps of increasing NH{sub 3} concentration, 2% to 50%, followed by the injection of pure ammonia. This report summarizes the planned passivation treatment scheme to stabilize the ACB and remove the potential hazards. It also includes basic information

  1. Charcoal burner

    SciTech Connect

    Bakic, M.C.

    1988-12-27

    A combustible fuel apparatus is described comprising: side walls formed contiguous with and extending upward from a base and converging to form a closed container, having stacked charcoal fuel particles therein. The base may be placed directly on a substantially horizontal surface and the container may be ignited and substantially burned to ash, and the charcoal fuel particles may be ignited and sufficiently burned for cooking, wherein the charcoal fuel particles are stacked on the base in a relatively stable position prior to the igniting of the container, and are maintained in a relatively stable position during and after the igniting and burning of the container, whereby a mound of ignited charcoal fuel particles remains on the substantially horizontal surface after the burning of the container, the mound having a configuration substantially similar to the shape of the container prior to the combustion thereof.

  2. Charcoal rot

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Charcoal rot is reported occasionally on alfalfa in the U.S. and has also been found in Australia, Pakistan, Uganda, east Africa, and the former Soviet Union. The fungus causing the disease is widespread throughout tropical and subtropical countries. It causes disease on more than 500 crop and we...

  3. Spacelab Charcoal Analyses

    NASA Technical Reports Server (NTRS)

    Slivon, L. E.; Hernon-Kenny, L. A.; Katona, V. R.; Dejarme, L. E.

    1995-01-01

    This report describes analytical methods and results obtained from chemical analysis of 31 charcoal samples in five sets. Each set was obtained from a single scrubber used to filter ambient air on board a Spacelab mission. Analysis of the charcoal samples was conducted by thermal desorption followed by gas chromatography/mass spectrometry (GC/MS). All samples were analyzed using identical methods. The method used for these analyses was able to detect compounds independent of their polarity or volatility. In addition to the charcoal samples, analyses of three Environmental Control and Life Support System (ECLSS) water samples were conducted specifically for trimethylamine.

  4. VOST charcoal specification study

    SciTech Connect

    Foster, A.L.; Bursey, J.T.

    1995-07-01

    The volatile organic sampling train, SW-846 Method 0030, (VOST) is currently one of the leading methodology`s available for the sampling and analysis of volatile organic hazardous compounds from stationary sources at very low levels. The method does not identify a specific equivalent sorbent, nor the performance specifications which would allow determination of an equivalent. Lot 104 petroleum-based charcoal is no longer commercially available. Laboratories are presently using a wide range of substitutes with varying performance from batch to batch of charcoal. To provide performance specifications and identify a replacement for SKC Lot 104 charcoal, a VOST charcoal specification study was initiated. Performance, cost, ease of handling, and plentiful supply make Anasorb 747 a good choice for replacement of SKX Lot 104.

  5. Desorption of TEDA from impregnated charcoals

    SciTech Connect

    Wood, G.

    1980-01-01

    Triethylenediamine (TEDA) is one of the most effective charcoal impregnants for trapping organic forms of radioiodine from air. It is used in air cleaning adsorbers, air samplers, and air purifying respirator canisters and cartridges for airborne radioiodine. Volatility of the pure crystals suggested the possibility of significant TEDA desorption in these applications, resulting in toxic levels of amine and/or degradation of sorbent efficiency. Measurements of TEDA desorption rates were made for four commercial charcoals. Temperatures of 70 to 120/sup 0/C were used to give levels detectable with a photoionization detector. Extrapolations to temperatures nearer normal ambient were made by using Clapeyron equation plots. Among three charcoals with the same 5% level of TEDA impregnation, desorption rates varied over factors as great as 10. Slopes of Clapeyron plots were similar, giving an average 25 kcal/mol heat of desorption. This corresponds to a doubling of the TEDA desorption rate with each 5/sup 0/C (9/sup 0/F) rise in temperature. Desorption rates were directly proportional to airflow rates or velocities through the test beds and independent of humidity. Desorption rates per unit weight of charcoal decreased exponentially with bed depth, presumably due to TEDA readsorption. Calculations based on this data and the geometry of a standard adsorber cell showed that at normal ambient temperatures: (1) concentrations of TEDA in effluent air are well below expected toxic levels; and (2) losses of TEDA may be significant. At elevated temperatures TEDA desorption rates are high enough to affect methyl iodide trapping efficiencies and, possibly, charcoal ignition temperatures.

  6. VOST charcoal specification study

    SciTech Connect

    Fuerst, R.G.; Foster, A.L.; Bursey, J.T.

    1996-12-31

    The volatile organic sampling train (VOST) is currently one the leading methodologies available for the sampling and analysis of volatile principal organic hazardous constituents (POHCs) and products of incomplete combustion (PICs) from stationary sources at very low levels. However, revisions to the original method are necessary to maintain VOST as a viable regulatory tool. To provide performance specifications and identify a replacement for SKC Lot 104 charcoal, a VOST charcoal specification study was initiated. The following carbon-based candidate sorbents were considered: Tenax-GR (a graphitized Tenax); a Petroleum-based Charcoal; Ambersorbe XE-340 (hydrophobic carbonized resin bead); Anasorb 747 (beaded active carbon with very regular pore size); Carbosieve{reg_sign} S-III (carbon molecular sieve); and a Beaded Activated Charcoal (BAC) (with a very regular pore size). The results indicated that Tenax-GR showed significantly poorer performance than the other candidates in preliminary experimental results. Ambersorb did not retain the gaseous volatile organic compounds tested as well as the others and recovery of vinyl chloride was very low at all levels of spiking. Carbosieve was eliminated as a candidate replacement because of cost and handling problems. The petroleum-based charcoal was eliminated because of difficulties in handling a finely-divided powder. The availability of Anasorb 747 proved to be the deciding factor between it and the BAC. Performance, cost, ease of handling, and plentiful supply make Anasorb{reg_sign} 747 a good choice for replacement of SKC Lot 104. 1 tab.

  7. Charcoal filter testing

    SciTech Connect

    Lyons, J.

    1997-08-01

    In this very brief, informal presentation, a representative of the US Nuclear Regulatory Commission outlines some problems with charcoal filter testing procedures and actions being taken to correct the problems. Two primary concerns are addressed: (1) the process to find the test method is confusing, and (2) the requirements of the reference test procedures result in condensation on the charcoal and causes the test to fail. To address these problems, emergency technical specifications were processed for three nuclear plants. A generic or an administrative letter is proposed as a more permanent solution. 1 fig.

  8. Commercial charcoal manufacture in Brazil

    SciTech Connect

    Rezende, M.E.; Lessa, A.; Pasa, V.; Sampaio, R.; Macedo, P.

    1993-12-31

    Brazil is the only country where charcoal has a major industrial us. Almost 40% of the pig iron and all the ferroalloys produced in the country are based on it and were established near Minas Gerais iron ore deposits using non-sustainable farm charcoal. Since the 1980s charcoal production from large eucalyptus forests is gradually increasing, accounting for 40% of the 8 million tonnes produced in 1991. Farm charcoal is produced when native forests are slashed to give way to farm land. Adequate techniques, labor rights or environmental concerns are not common in this scenario. In large eucalyptus forests charcoal production has a different business approach. Several kinds of masonry ovens are used in both scenarios. Continuous carbonization kilns are not feasible yet because of their high capital cost. The search for a new cheapest design or for the upgrading of the carbonization byproducts is a must. Promising results are shown. Plastics and fine chemicals were already obtained from wood tar. The first Brazilian pilot plant for wood tar fractionation will be started by 9/93. Ironworks have different profiles. Some plants are up-to-date integrated mini-steelworks. Others are small producers of pig ingots. They have in common the need to face coke ironmaking route. Brazilian exports of charcoal based iron and steel products have attained the goal until now. Future charcoal competitiveness will not be so easy. Although expertises believe that coke prices can not stand low for long time it poses additional difficulty to the Brazilian charcoal ironmaker. Three scenarios projected for the future of charcoal ironmaking show that as long as charcoal production costs are properly managed, charcoal will be competitive with coke. The authors defend a common research program that looks for technologies suited to the Brazilian reality.

  9. Replacement of charcoal sorbent in the VOST

    SciTech Connect

    Johnson, L.D.; Fuerst, R.G.; Foster, A.L.; Bursey, J.T.

    1993-01-01

    EPA Method 0030, the Volatile Organic Sampling Train (VOST), for sampling volatile organics from stationary sources, specifies the use of petroleum-base charcoal in the second sorbent tube. Charcoal has proven to be a marginal performer as a sampling sorbent, partly due to inconsistency in analyte recovery. In addition, commercial availability of petroleum charcoal for VOST tubes has been variable. Lack of data on comparability and variability of charcoals for VOST application has created uncertainty when other charcoals are substituted. Five potential sorbent replacements for charcoal in Method 0030 were evaluated along with a reference charcoal. Two of the sorbents tested, Ambersorb XE-340 and Tenax GR, did not perform well enough to qualify as replacements. Three candidates, Anasorb 747, Carbosieve S-III and Kureha Beaded Activated Charcoal, performed adequately, and produced statistically equivalent results. Anasorb 747 appears to be an acceptable replacement for petroleum charcoal, based on a combination of performance, availability, and cost.

  10. Post-Flight Sampling and Loading Characterization of Trace Contaminant Control Subassembly Charcoal

    NASA Technical Reports Server (NTRS)

    Perry, J. L.; Cole, H. E.; Cramblitt, E. L.; El-Lessy, H. N.; Manuel, S.; Tucker, C. D.

    2003-01-01

    Trace chemical contaminants produced by equipment offgassing and human metabolic processes are removed from the atmosphere of the International Space Station s U.S. Segment by a trace contaminant control subassembly (TCCS). The TCCS employs a combination of physical adsorption, thermal catalytic oxidation, and chemical adsorption processes to accomplish its task. A large bed of granular activated charcoal is a primary component of the TCCS. The charcoal contained in this bed, known as the charcoal bed assembly (CBA), is expendable and must be replaced periodically. Pre-flight engineering analyses based upon TCCS performance testing results established a service life estimate of 1 year. After nearly 1 year of cumulative in-flight operations, the first CBA was returned for refurbishment. Charcoal samples were collected and analyzed for loading to determine the best estimate for the CBAs service life. A history of in-flight TCCS operations is presented as well as a discussion of the charcoal sampling procedures and chemical analysis results. A projected service life derived from the observed charcoal loading is provided. Recommendations for better managing TCCS resources are presented.

  11. Development of charcoal sorbents for helium cryopumping

    SciTech Connect

    Sedgley, D.W.; Tobin, A.G.

    1984-01-01

    Testing of the cryogenically cooled charcoal using fusion-compatible binders for pumping helium has shown promising results. The program demonstrated comparable or improved performance with these binders compared to the charcoal (type and size) using an epoxy binder.

  12. European auxiliary propulsion, 1972

    NASA Technical Reports Server (NTRS)

    Holcomb, L. B.

    1972-01-01

    The chemical and electric auxiliary propulsion technology of the United Kingdom, France, and West Germany is discussed in detail, and the propulsion technology achievements of Italy, India, Japan, and Russia are reviewed. A comparison is presented of Shell 405 catalyst and a European spontaneous hydrazine catalyst called CNESRO I. Finally, conclusions are drawn regarding future trends in European auxiliary propulsion technology development.

  13. Radon-222 activity flux measurement using activated charcoal canisters: revisiting the methodology.

    PubMed

    Alharbi, Sami H; Akber, Riaz A

    2014-03-01

    The measurement of radon ((222)Rn) activity flux using activated charcoal canisters was examined to investigate the distribution of the adsorbed (222)Rn in the charcoal bed and the relationship between (222)Rn activity flux and exposure time. The activity flux of (222)Rn from five sources of varying strengths was measured for exposure times of one, two, three, five, seven, 10, and 14 days. The distribution of the adsorbed (222)Rn in the charcoal bed was obtained by dividing the bed into six layers and counting each layer separately after the exposure. (222)Rn activity decreased in the layers that were away from the exposed surface. Nevertheless, the results demonstrated that only a small correction might be required in the actual application of charcoal canisters for activity flux measurement, where calibration standards were often prepared by the uniform mixing of radium ((226)Ra) in the matrix. This was because the diffusion of (222)Rn in the charcoal bed and the detection efficiency as a function of the charcoal depth tended to counterbalance each other. The influence of exposure time on the measured (222)Rn activity flux was observed in two situations of the canister exposure layout: (a) canister sealed to an open bed of the material and (b) canister sealed over a jar containing the material. The measured (222)Rn activity flux decreased as the exposure time increased. The change in the former situation was significant with an exponential decrease as the exposure time increased. In the latter case, lesser reduction was noticed in the observed activity flux with respect to exposure time. This reduction might have been related to certain factors, such as absorption site saturation or the back diffusion of (222)Rn gas occurring at the canister-soil interface.

  14. Carcinogenic PAH in waterpipe charcoal products.

    PubMed

    Sepetdjian, Elizabeth; Saliba, Najat; Shihadeh, Alan

    2010-11-01

    Because narghile waterpipe (shisha, hooka) smoking normally involves the use of burning charcoal, smoke inhaled by the user contains constituents originating from the charcoal in addition to those from the tobacco. We have previously found that charcoal accounts for most of the polyaromatic hydrocarbons (PAH) and carbon monoxide in the smoke of the waterpipe, both of which are present in alarming quantities. Because charcoal manufacturing conditions favor formation of PAH, it is reasonable to assume that charcoal sold off the shelf may be contaminated by PAH residues. These residues may constitute a significant fraction of the PAH inhaled by the waterpipe user and those in her/his vicinity. We measured PAH residues on three kinds of raw waterpipe charcoal sampled from Beirut stores and cafés. We found that PAH residues in raw charcoal can account for more than half of the total PAH emitted in the mainstream and sidestream smoke, and about one sixth of the carcinogenic 5- and 6-ring PAH compounds. Total PAH content of the three charcoal types varied systematically by a factor of six from the charcoal with the least to the greatest PAH residue. These findings indicate the possibility of regulating charcoal carcinogen content. PMID:20807559

  15. Carcinogenic PAH in waterpipe charcoal products.

    PubMed

    Sepetdjian, Elizabeth; Saliba, Najat; Shihadeh, Alan

    2010-11-01

    Because narghile waterpipe (shisha, hooka) smoking normally involves the use of burning charcoal, smoke inhaled by the user contains constituents originating from the charcoal in addition to those from the tobacco. We have previously found that charcoal accounts for most of the polyaromatic hydrocarbons (PAH) and carbon monoxide in the smoke of the waterpipe, both of which are present in alarming quantities. Because charcoal manufacturing conditions favor formation of PAH, it is reasonable to assume that charcoal sold off the shelf may be contaminated by PAH residues. These residues may constitute a significant fraction of the PAH inhaled by the waterpipe user and those in her/his vicinity. We measured PAH residues on three kinds of raw waterpipe charcoal sampled from Beirut stores and cafés. We found that PAH residues in raw charcoal can account for more than half of the total PAH emitted in the mainstream and sidestream smoke, and about one sixth of the carcinogenic 5- and 6-ring PAH compounds. Total PAH content of the three charcoal types varied systematically by a factor of six from the charcoal with the least to the greatest PAH residue. These findings indicate the possibility of regulating charcoal carcinogen content.

  16. Factors Affecting the Estimation of Indoor Radon Using Passive Activated Charcoal Canisters

    NASA Astrophysics Data System (ADS)

    Scarpitta, Salvatore Charles

    1990-01-01

    Adsorption and desorption studies of 20 activated charcoals were conducted in a monolayer and a packed bed utilizing tracer gases. Kinetic studies, using xenon-133, demonstrate the existence of a two-compartment micropore volume with entrance capillaries which together determine the response characteristics of the charcoal to external concentration gradients of tracer gases. This new two -compartment model adequately describes the adsorption and desorption dynamics of radon in the presence of water vapor. Measurements with charcoal exposed to water vapor and Rn-222 in a monolayer and packed bed for exposure intervals of 1-7 days demonstrate that the uptake rate and total quantity of adsorbed Rn-222 are highly dependent upon the amount of water adsorbed. The effect of CO_2 on radon adsorption is small in any charcoal. The measured effective diffusion coefficient of radon in a packed bed of a peat based charcoal at 15% humidity and 25^circC is 7.97 times 10^{-6} cm^2/s. Condensed water vapor in the entrance capillaries reduces the effective pore radius, increasing the diffusion half-time, both into and out of the charcoal. The amount of adsorbed water per gram of charcoal required to block the entrance capillaries varies with the charcoal type. The proposed term for this quantity is the "break-point". A two-stage diffusion barrier charcoal monitor with a long diffusion path length was developed. This design inhibits passive airflow while maintaining the amount of adsorbed water vapor in the primary charcoal adsorbent below the break-point. Water removal at the entry port allows for longer exposure times improving the integrating capability necessary for indoor exposure assessment. The long diffusion path length increases the integration time -constant for radon adsorption normally 24 hours for conventional open-faced canisters to 50 hours for the improved canister. The increased integration time-constant allows for a 7 day sample to be measured at 70% humidity and 23

  17. Auxiliary incinerator apparatus

    SciTech Connect

    Crawford, J.P.

    1987-08-11

    An auxiliary incinerator apparatus is described for an incinerator comprising: a main incinerator having primary and secondary chambers formed with a plurality of refractory walls, the main incinerator having a main door into the primary chamber, and the main incinerator having an outer framework and walls spaced from the refractory walls, and one refractory wall having an opening therethrough; a refractory passageway extending from the opening in the main incinerator wall to the outer wall and having an opening through the outer wall; an auxiliary incinerator attached to one side of the main incinerator adjacent to the opening from the refractory passageway through the outer wall, the auxiliary incinerator having an incineration chamber formed therein with an opening thereinto; and auxiliary door means for opening and closing over the opening from the refractory passageway through the outer wall and for opening and closing over the opening into the auxiliary incinerator, whereby partially incinerated materials can be moved from the main incinerator to the auxiliary incinerator for further combustion.

  18. Severe theophylline poisoning: charcoal haemoperfusion or haemodialysis?

    PubMed

    Higgins, R M; Hearing, S; Goldsmith, D J; Keevil, B; Venning, M C; Ackrill, P

    1995-04-01

    Theophylline poisoning with a blood level of 183 mg/l in a 38-year-old man was treated with activated charcoal by mouth, but despite this the blood level of theophylline rose and there was circulatory collapse with rhabdomyolysis, acute renal failure and hyperthermia. Treatment with charcoal haemoperfusion and simultaneous haemodialysis was given, followed by continuous arteriovenous haemodialysis (CAVHD). Mean extraction rates of theophylline were 26% during CAVHD, and 86% during combined dialysis and charcoal haemoperfusion. During combined treatment, the mean extraction rate of haemodialysis was 62%, compared with 48% for charcoal haemoperfusion. In summary, activated charcoal given by mouth may be unable to prevent a rise in blood levels and the development of complications after substantial theophylline overdose. If theophylline is to be removed from the blood, a combination of charcoal haemoperfusion and haemodialysis will give the best clearance, but haemodialysis alone may be effective.

  19. Charcoal hemoperfusion in bupropion overdose.

    PubMed

    Akdemir, Hızır Ufuk; Calışkan, Fatih; Duran, Latif; Katı, Celal; Güngörer, Bülent; Ocak, Metin

    2014-10-01

    Bupropion is a relatively new and popular medication for depression, with seizures as its major side effect. In the literature, there are insufficient data about hemodialysis following bupropion overdose. A 23-year-old female patient was brought to our emergency department with acute change in mental status and seizure after deliberate self-poisoning with approximately 25-30 tablets of bupropion hydrochloride. Her Glasgow coma scale score was 8/15. The patient underwent hemodialysis about 4 hours later. After 4 hours of extracorporeal treatment, she became conscious and was extubated. We present a case of full recovery after charcoal hemoperfusion following a bupropion overdose.

  20. Charcoal/Nitrogen Adsorption Cryocooler

    NASA Technical Reports Server (NTRS)

    Bard, Steven

    1987-01-01

    Refrigerator with no wear-related moving parts produces 0.5 W of cooling at 118 K. When fully developed, refrigerator needs no electrical power, and life expectancy of more than 10 yr, operates unattended to cool sensitive infrared detectors for long periods. Only moving parts in adsorption cryocooler are check valves. As charcoal is cooled in canister, gas pressure drops, allowing inlet check valve to open and admit more nitrogen. When canister is heated, pressure rises, closing inlet valve and eventually opening outlet valve.

  1. CHARCOAL-PRODUCING INDUSTRIES IN NORTHEASTERN BRAZIL

    EPA Science Inventory

    Charcoal workers in northeastern Brazil: Occupational risks and effects of exposure to wood smoke
    ABSTRACT
    Brazil has the largest production of charcoal in the world, which is used mostly in the iron and steel industries. In most of the production sites, the process is ba...

  2. Development of charcoal sorbents for helium cryopumping

    SciTech Connect

    Sedgley, D.W.; Tobin, A.G.

    1985-09-30

    Improved methods for cryopumping helium were developed for application to fusion reactors where high helium generation rates are expected. This study period evaluated charcoal particle size, bonding agent type and thickness, and substrate thickness. The optimum combination of charcoal, bond, and substrate was used to form a scaled-up panel for evaluation in the Tritium Systems Test Assembly (TSTA) at Los Alamos. The optimum combination is a 12 x 30 mesh coconut charcoal attached to a 0.48 cm thick copper substrate by a 0.015 cm thick silver phosphorus copper braze. A copper cement bond for attaching charcoal to a substrate was identified and tested. Helium pumping performance of this combination was comparable to that of the charcoal braze system. Environmental tests showed the charcoal's susceptibility to vacuum chamber contamination. Performance degradation followed exposure of ambient temperature charcoal to a vacuum for prolonged periods. Maintaining a liquid nitrogen-cooled shield between the charcoal and the source of contamination prevented this degradation. A combination of bake-out and LN shielding effected recovery of degraded performance.

  3. Evaluation of radon adsorption characteristics of a coconut shell-based activated charcoal system for radon and thoron removal applications.

    PubMed

    Karunakara, N; Sudeep Kumara, K; Yashodhara, I; Sahoo, B K; Gaware, J J; Sapra, B K; Mayya, Y S

    2015-04-01

    Radon ((222)Rn), thoron ((220)Rn), and their decay products contribute a major fraction (more than 50%) of doses received from ionisation radiation in public domain indoor environments and occupation environments such as uranium mines, thorium plants, and underground facilities, and are recognised as important radiological hazardous materials, which need to be controlled. This paper presents studies on the removal of (222)Rn and (220)Rn from air using coconut shell-based granular activated charcoal cylindrical adsorber beds. Experiments were conducted to evaluate the (222)Rn and (220)Rn adsorption characteristics, and the mitigation efficiency of coconut-based activated charcoal available in India. The performance parameters evaluated include breakthrough time (τ) and adsorption coefficient (K), and degassing characteristics of the charcoal bed of varying dimensions at different flow rates. While the breakthrough for (222)Rn occurred depending on the dimension of the adsorber bed and flow rates, for (220)Rn, the breakthrough did not occur. The breakthrough curve exhibited a stretched S-shape response, instead of the theoretically predicted sharp step function. The experiments confirm that the breakthrough time individually satisfies the quadratic relationship with respect to the diameter of the bed, and the linear relationship with respect to the length, as predicted in the theory. The K value varied in the range of 2.3-4.12 m(3) kg(-1) with a mean value of 2.99 m(3) kg(-1). The K value was found to increase with the increase in flow rate. Heating the charcoal to ∼ 100 °C resulted in degassing of the adsorbed (222)Rn, and the K of the degassed charcoal and virgin charcoal were found to be similar with no deterioration in performance indicating the re-usability of the charcoal.

  4. Evaluation of radon adsorption characteristics of a coconut shell-based activated charcoal system for radon and thoron removal applications.

    PubMed

    Karunakara, N; Sudeep Kumara, K; Yashodhara, I; Sahoo, B K; Gaware, J J; Sapra, B K; Mayya, Y S

    2015-04-01

    Radon ((222)Rn), thoron ((220)Rn), and their decay products contribute a major fraction (more than 50%) of doses received from ionisation radiation in public domain indoor environments and occupation environments such as uranium mines, thorium plants, and underground facilities, and are recognised as important radiological hazardous materials, which need to be controlled. This paper presents studies on the removal of (222)Rn and (220)Rn from air using coconut shell-based granular activated charcoal cylindrical adsorber beds. Experiments were conducted to evaluate the (222)Rn and (220)Rn adsorption characteristics, and the mitigation efficiency of coconut-based activated charcoal available in India. The performance parameters evaluated include breakthrough time (τ) and adsorption coefficient (K), and degassing characteristics of the charcoal bed of varying dimensions at different flow rates. While the breakthrough for (222)Rn occurred depending on the dimension of the adsorber bed and flow rates, for (220)Rn, the breakthrough did not occur. The breakthrough curve exhibited a stretched S-shape response, instead of the theoretically predicted sharp step function. The experiments confirm that the breakthrough time individually satisfies the quadratic relationship with respect to the diameter of the bed, and the linear relationship with respect to the length, as predicted in the theory. The K value varied in the range of 2.3-4.12 m(3) kg(-1) with a mean value of 2.99 m(3) kg(-1). The K value was found to increase with the increase in flow rate. Heating the charcoal to ∼ 100 °C resulted in degassing of the adsorbed (222)Rn, and the K of the degassed charcoal and virgin charcoal were found to be similar with no deterioration in performance indicating the re-usability of the charcoal. PMID:25658471

  5. Dental Auxiliary Occupations. Interim Report.

    ERIC Educational Resources Information Center

    Kingston, Richard D.

    As part of a dental auxiliaries project, a Dental Auxiliary National Technical Advisory Committee was established, and its major undertaking was to assist in the development of a functional inventory for each of the three dental auxiliary occupations (dental assisting, dental hygiene, and dental laboratory technology). The analysis consisted of…

  6. Charcoal and activated carbon at elevated pressure

    SciTech Connect

    Antal, M.J. Jr.; Dai, Xiangfeng; Norberg, N.

    1995-12-01

    High quality charcoal has been produced with very high yields of 50% to 60% from macadamia nut and kukui nut shells and of 44% to 47% from Eucalyptus and Leucaena wood in a bench scale unit at elevated pressure on a 2 to 3 hour cycle, compared to commercial practice of 25% to 30% yield on a 7 to 12 day operating cycle. Neither air pollution nor tar is produced by the process. The effects of feedstock pretreatments with metal additives on charcoal yield are evaluated in this paper. Also, the influences of steam and air partial pressure and total pressure on yields of activated carbon from high yield charcoal are presented.

  7. 49 CFR 176.405 - Stowage of charcoal.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Stowage of charcoal. 176.405 Section 176.405... Materials § 176.405 Stowage of charcoal. (a) Before stowing charcoal Division 4.2 (flammable solid), UN 1361... petroleum product, a vegetable or animal oil, nitrate, or sulfur, must be removed. (b) Charcoal packed...

  8. 49 CFR 176.405 - Stowage of charcoal.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Stowage of charcoal. 176.405 Section 176.405... Materials § 176.405 Stowage of charcoal. (a) Before stowing charcoal Division 4.2 (flammable solid), UN 1361... petroleum product, a vegetable or animal oil, nitrate, or sulfur, must be removed. (b) Charcoal packed...

  9. 49 CFR 176.405 - Stowage of charcoal.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Stowage of charcoal. 176.405 Section 176.405... Materials § 176.405 Stowage of charcoal. (a) Before stowing charcoal Division 4.2 (flammable solid), UN 1361... petroleum product, a vegetable or animal oil, nitrate, or sulfur, must be removed. (b) Charcoal packed...

  10. 49 CFR 176.405 - Stowage of charcoal.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Stowage of charcoal. 176.405 Section 176.405... Materials § 176.405 Stowage of charcoal. (a) Before stowing charcoal Division 4.2 (flammable solid), UN 1361... petroleum product, a vegetable or animal oil, nitrate, or sulfur, must be removed. (b) Charcoal packed...

  11. 49 CFR 176.405 - Stowage of charcoal.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Stowage of charcoal. 176.405 Section 176.405... Materials § 176.405 Stowage of charcoal. (a) Before stowing charcoal Division 4.2 (flammable solid), UN 1361... petroleum product, a vegetable or animal oil, nitrate, or sulfur, must be removed. (b) Charcoal packed...

  12. Development of an incineration system for pulverized spent charcoal

    SciTech Connect

    Furukawa, Osamu; Shibata, Minoru; Kani, Koichi

    1995-12-31

    In the existing charcoal treatment system granular charcoal is charged directly into an incinerator together with other combustible waste. Since the combustion rate of the charcoal is slow in this system, there is a problem that unburnt charcoal accumulates at the bottom of the incinerator, when incineration is performed for an extended period of time. To prevent this difficulty, the combustion rate of the charcoal must be limited to 6 kg/h. To increase the incineration rate of charcoal, the authors have developed a system in which the charcoal is pulverized and incinerated while it is mixed with propane gas. The operational performance of this system was tested using an actual equipment.

  13. Design and Operating Criteria for Fluorine Disposal by Reaction with Charcoal

    NASA Technical Reports Server (NTRS)

    Schmidt, Harold W.

    1959-01-01

    Experiments with the charcoal-fluorine reaction for the disposal of fluorine have shown generally that this method is effective over a wide range of conditions. Pure fluorine or fluorine diluted with nitrogen to concentrations as low as 0.3 percent fluorine may be disposed of efficiently within the rate limitation. Maximum feed rates have been established and are inversely proportional to the charcoal-bed particle diameter. Moisture content in the charcoal had no appreciable effect on the disposal efficiency after the reaction zone was established and the moisture was driven off by the heat of reaction. There was no evidence of bed poisoning resulting from continued use. Design parameters may be based on the stoichiometric requirements plus sufficient excess charcoal to maintain desired efficiency toward the end of a disposal operation. The length of time a given reactor may be used continuously is limited by the rate of fluorine input and the resistance of the system to heat and fluorine attack. Refractory-lined reactors have been in routine field use at the Lewis Research Center for over a year and have given satisfactory service over a wide range of conditions.

  14. Mechanically robust, chemically inert superhydrophobic charcoal surfaces.

    PubMed

    Xie, Jian-Bo; Li, Liang; Knyazeva, Anastassiya; Weston, James; Naumov, Panče

    2016-08-11

    We report a fast and cost-effective strategy towards the preparation of superhydrophobic composites where a double-sided adhesive tape is paved with charcoal particles. The composites are mechanically robust, and resistant to strong chemical agents. PMID:27405255

  15. Mapping the Legacies of Historic Charcoal Production

    NASA Astrophysics Data System (ADS)

    Schneider, A.; Raab, A.; Raab, T. A.; Takla, M.; Nicolay, A.; Rösler, H.

    2014-12-01

    The historic production of charcoal is an important component of the late Holocene fire history for many landscapes. Charcoal production can have numerous effects on ecosystems, e.g., through changes in forest area and structure, or through the effects of pyrolysis, charcoal and ash addition to soils. To assess such effects, it is necessary to understand the spatial extent and patterns of historic charcoal production, which has so far hardly been approached for the Northern European Lowlands. In the forefield of the open-cast mine Jänschwalde (north of Cottbus, Germany), archaeological excavations have revealed one of the largest charcoal production fields described so far. For this area, we applied and evaluated different methods for mapping the spatial distribution of charcoal kiln remains. We present methods and results of our work in this exceptionally well-described charcoal production field and of additional studies on kiln site distribution in regions of the Northern European Lowlands. The large-scale excavations in the mine forefield provide exact information on kiln site geometry. Using airborne laser scanning elevation models, the mapping of kiln sites could be extended to areas beyond the mine forefield. To detect kiln sites for larger areas, an automated GIS based mapping routine, based on a combination of morphometric parameters, was developed and evaluated. By manual digitization from Shaded Relief Maps, more than 5000 kiln sites in an area of 32 km2 were detected in the Jänschwalde mine forefield, with 1355 kiln sites that are wider than 12 m. These relatively large kiln sites could be mapped with detection rates that are close to those of manual digitization using the automated routine. First results for different study areas indicate that charcoal production is a so far underestimated component of the land use history in many parts of the Northern European Lowlands.

  16. New emission controls for Missouri batch-type charcoal kilns

    SciTech Connect

    Yronwode, P.; Graf, W.J.

    1999-07-01

    Charcoal kilns have been exempted from air emission regulation in the state of Missouri. Today, 80% of US charcoal production takes place in Missouri. As a result of a petition filed by people in the area around an installation in southern Missouri, the US Environmental Protection Agency (EPA) set up air monitors and measured ambient air levels at that charcoal manufacturing installation. These monitors yielded the highest particulate matter less than 10 micron (PM{sub 10}) levels ever recorded in the state. Earlier stack testing at another charcoal manufacturing installation indicated that toxics and carcinogens are present in charcoal kiln air emissions. A Charcoal Kiln Workgroup was formed to determine the Best Available Control Technology (BACT) for charcoal kilns and to draft a charcoal kiln rule that requires BACT. The BACT report determined that afterburners were suitable for controlling emissions from batch-type charcoal kilns. In addition, the charcoal industry supported incorporating the BACT limits and requirements into an enforceable state rule and submitting this rule to the EPA for federal approval. A consent agreement between the EPA and three major charcoal companies was signed with provisions to install, operate, and maintain emission control devices on charcoal kilns. This agreement was to settle complaints alleging that the three major charcoal producers had failed to report toxic air emissions to federal and state regulators. The agreement provided that industry would install control devices on a set schedule with some charcoal kilns being shut down.

  17. An improved sup 222 Rn canister using a two-stage charcoal system

    SciTech Connect

    Scarpitta, S.C.; Harley, N.H. )

    1991-02-01

    A prototype for an improved passive {sup 222}Rn canister (R-Canister) was designed and compared to conventional charcoal canisters for its adsorptive and desorptive characteristics following exposures to {sup 222}Rn at 23{degrees}C in the presence of water vapor. The R-Canister, containing a two-stage charcoal system, minimizes the adverse effects of water vapor by maintaining the amount of adsorbed water vapor in the primary Rn adsorbent below the break-point of the charcoal. This is achieved by the placement of a desiccant charcoal cartridge 6 cm above the primary Rn adsorbent. The optimal bed depth of the primary adsorbent, determined from a diffusion study, was found to be 2.3 cm. The measured value for the effective diffusion coefficient of RN in a peat-based charcoal at 15% humidity and 25{degrees}C is 7.97 x 10(-10) m2 s-1. Exposures to 70% humidity for 7 d increased the buildup time-constant of Rn in the R-Canisters by 33% as compared to R-Canisters exposed to 15% humidity. At relative humidities ranging from 15-70%, the {sup 222}Rn buildup time-constant of the R-Canister ranged from 43-94 h, whereas the desorption time-constant ranged from 46-64 h. Typical buildup time-constants and desorption time-constants for conventional fully-opened charcoal canisters currently in field use ranged from 30-43 h and 17-29 h, respectively, over the same range of humidities.

  18. Effect of activated charcoal on the pharmacokinetics of pholcodine, with special reference to delayed charcoal ingestion.

    PubMed

    Laine, K; Kivistö, K T; Ojala-Karlsson, P; Neuvonen, P J

    1997-02-01

    We conducted a randomized study with four parallel groups to investigate the effect of single and multiple doses of activated charcoal on the absorption and elimination of pholcodine administered in a cough syrup. The first group received 100 mg of pholcodine on an empty stomach with water only (control); the second group took 25 g of activated charcoal immediately after pholcodine; the third group received 25 g of activated charcoal 2 h and the fourth group 5 h after ingestion of the 100-mg dose of pholcodine. In addition, the fourth group received multiple doses (10 g each) of charcoal every 12 h for 84 h. Blood samples were collected for 96 h and urine for 72 h. Pholcodine concentrations were measured by high-performance liquid chromatography. A significant reduction in absorption was found when charcoal was administered immediately after pholcodine; the AUC0-96h was reduced by 91% (p < 0.0005), the Cmax by 77% (p < 0.0005), and the amount of pholcodine excreted into urine by 85% (p < 0.0005). When charcoal was administered 2 h after pholcodine, the AUC0-96h was reduced by 26% (p = 0.002), the Cmax by 23% (p = NS), and the urinary excretion by 28% (p = 0.004). When administered 5 h after pholcodine, charcoal produced only a 17% reduction in the AUC0-96h (p = 0.06), but reduced the further absorption of pholcodine still present in the gastrointestinal tract at the time of charcoal administration, as measured by AUC5-96h (p = 0.006). Repeated administration of charcoal failed to accelerate the elimination of pholcodine. We conclude that activated charcoal is effective in preventing the absorption of pholcodine, and its administration can be beneficial even several hours after pholcodine ingestion. PMID:9029746

  19. Effect of activated charcoal on the pharmacokinetics of pholcodine, with special reference to delayed charcoal ingestion.

    PubMed

    Laine, K; Kivistö, K T; Ojala-Karlsson, P; Neuvonen, P J

    1997-02-01

    We conducted a randomized study with four parallel groups to investigate the effect of single and multiple doses of activated charcoal on the absorption and elimination of pholcodine administered in a cough syrup. The first group received 100 mg of pholcodine on an empty stomach with water only (control); the second group took 25 g of activated charcoal immediately after pholcodine; the third group received 25 g of activated charcoal 2 h and the fourth group 5 h after ingestion of the 100-mg dose of pholcodine. In addition, the fourth group received multiple doses (10 g each) of charcoal every 12 h for 84 h. Blood samples were collected for 96 h and urine for 72 h. Pholcodine concentrations were measured by high-performance liquid chromatography. A significant reduction in absorption was found when charcoal was administered immediately after pholcodine; the AUC0-96h was reduced by 91% (p < 0.0005), the Cmax by 77% (p < 0.0005), and the amount of pholcodine excreted into urine by 85% (p < 0.0005). When charcoal was administered 2 h after pholcodine, the AUC0-96h was reduced by 26% (p = 0.002), the Cmax by 23% (p = NS), and the urinary excretion by 28% (p = 0.004). When administered 5 h after pholcodine, charcoal produced only a 17% reduction in the AUC0-96h (p = 0.06), but reduced the further absorption of pholcodine still present in the gastrointestinal tract at the time of charcoal administration, as measured by AUC5-96h (p = 0.006). Repeated administration of charcoal failed to accelerate the elimination of pholcodine. We conclude that activated charcoal is effective in preventing the absorption of pholcodine, and its administration can be beneficial even several hours after pholcodine ingestion.

  20. Handbook of charcoal making: the traditional and industrial methods

    SciTech Connect

    Emrich, W.

    1985-01-01

    The reviewer credits this handbook with expanding knowledge about the economic value of charcoal, particularly in the European area. The 10 chapters are: (1) history and fundamentals of the charcoal process, (2) traditional methods of the smallholder producer, (3) concepts and technology for the industrial producer, (4) recovering commercial products from pyrolysis oil, (5) raw materials supply, (6) end-use markets for by-products, (7) planning a charcoal venture, (8) charcoal briquettes and activated charcoal, (9) safety precautions and environmental considerations, and (10) charcoal laboratory work. Each chapter lists references. There are four appendices.

  1. Student Services and Auxiliary Enterprises

    ERIC Educational Resources Information Center

    Pittman, Jeffrey S.

    2012-01-01

    A greater number of campuses have broadened concepts related to student development connecting traditional student affairs and campus auxiliary services. This connection is increasingly evident in the evolution of sustainability concerns and activities. This chapter explores the role of campus auxiliaries in the promotion of campus environmental…

  2. Recovery of Technetium Adsorbed on Charcoal

    SciTech Connect

    Engelmann, Mark D.; Metz, Lori A.; Ballou, Nathan E.

    2006-05-01

    Two methods capable of near complete recovery of technetium adsorbed on charcoal are presented. The first involves liquid extraction of the technetium from the charcoal by hot 4M nitric acid. An average recovery of 98% (n=3) is obtained after three rounds of extraction. The second method involves dry ashing with air in a quartz combustion tube at 400-450 C. This method yields an average recovery of 96% (n=5). Other thermal methods were attempted, but resulted in reduced recovery and incomplete material balance

  3. Auxiliary lubrication pump apparatus

    SciTech Connect

    Glesmann, H.C.; Thomas, R.G.

    1987-02-10

    This patent describes an auxiliary lubrication pump apparatus for use with a towing vehicle having an engine switch, a battery, and an interior compartment, and a towed vehicle having an automatic transmission which requires forced lubrication while being towed. The apparatus comprises: (a) a lubrication pump; (b) a transmission to pump hose connected between the automatic transmission and the lubrication pump; (c) a valve having at least one signal output and two inputs: (d) a hose means for connecting an output of the lubrication pump to one of the inputs of the valve; (e) a first outflow hose for connecting the automatic transmission to another input of the valve; (f) a second output hose for connecting the output of the valve to the automatic transmission; (g) pressure sensing means positioned to sense pressure as regards the second outflow hose; and (h) control means responsive to the pressure sensing means and having switch means for providing electricity to the lubrication pump and to provide an alarm whenever the control means detects through the pressure sensing means that inadequate pressure exists.

  4. Charcoal from the pyrolysis of rapeseed plant straw-stalk

    SciTech Connect

    Karaosmanoglu, F.; Tetik, E.

    1999-07-01

    Charcoal is an important product of pyrolysis of biomass sources. Charcoal can be used for domestic, agricultural, metallurgical, and chemical purposes. In this study different characteristics of charcoal, one of the rape seed plant straw-stalk pyrolysis product, was researched and presented as candidates.

  5. Emissions of air pollutants from indoor charcoal barbecue.

    PubMed

    Huang, Hsiao-Lin; Lee, Whei-May Grace; Wu, Feng-Shu

    2016-01-25

    Ten types of commercial charcoal commonly used in Taiwan were investigated to study the potential health effects of air pollutants generated during charcoal combustion in barbecue restaurants. The charcoal samples were combusted in a tubular high-temperature furnace to simulate the high-temperature charcoal combustion in barbecue restaurants. The results indicated that traditional charcoal has higher heating value than green synthetic charcoal. The amount of PM10 and PM2.5 emitted during the smoldering stage increased when the burning temperature was raised. The EF for CO and CO2 fell within the range of 68-300 and 644-1225 g/kg, respectively. Among the charcoals, the lowest EF for PM2.5 and PM10 were found in Binchōtan (B1). Sawdust briquette charcoal (I1S) emitted the smallest amount of carbonyl compounds. Charcoal briquettes (C2S) emitted the largest amount of air pollutants during burning, with the EF for HC, PM2.5, PM10, formaldehyde, and acetaldehyde being the highest among the charcoals studied. The emission of PM2.5, PM10, formaldehyde, and acetaldehyde were 5-10 times those of the second highest charcoal. The results suggest that the adverse effects of the large amounts of air pollutants generated during indoor charcoal combustion on health and indoor air quality must not be ignored.

  6. Sawdust and Charcoal: Fuel for Raku.

    ERIC Educational Resources Information Center

    Brisson, Harriet E.

    1980-01-01

    Raku is an ancient Japanese process of firing pottery in which the bisqued piece is glazed and placed in a preheated kiln. Described are the benefits of substituting sawdust and charcoal for firing pottery by those people who do not have access to a kiln. (KC)

  7. Fire-derived charcoal causes loss of forest humus.

    PubMed

    Wardle, David A; Nilsson, Marie-Charlotte; Zackrisson, Olle

    2008-05-01

    Fire is a global driver of carbon storage and converts a substantial proportion of plant biomass to black carbon (for example, charcoal), which remains in the soil for thousands of years. Black carbon is therefore often proposed as an important long-term sink of soil carbon. We ran a 10-year experiment in each of three boreal forest stands to show that fire-derived charcoal promotes loss of forest humus and that this is associated with enhancement of microbial activity by charcoal. This result shows that charcoal-induced losses of belowground carbon in forests can partially offset the benefits of charcoal as a long-term carbon sink.

  8. Investigation on cotton stalk and bamboo sawdust carbonization for barbecue charcoal preparation.

    PubMed

    Xiong, Shaowu; Zhang, Shouyu; Wu, Qiaomei; Guo, Xi; Dong, Aixia; Chen, Chuan

    2014-01-01

    In the paper, biochar preparation from cotton stalk and bamboo sawdust by carbonization process was addressed. The physical and chemical properties and combustion characteristics of the biochar prepared using a tubular fixed bed were investigated. The combustion character index (S), the ignition temperature (Ti) and burnout temperature (Tf) were used to evaluate the combustion characteristics of the biochars. The results indicate that the yield and the volatile yield of the biochar decrease and the fixed carbon yield increases with the increase of the carbonization temperature. The ignition temperature and burnout temperature of the biochar increase and the value of S decreases when the carbonization temperature increases. The biochar produced from cotton stalk shows better combustion characteristics than the bamboo sawdust biochar does. Compared with commercial barbecue charcoal, the cotton stalk biochar produced under 600 °C can be utilized as barbecue charcoal.

  9. Emissions of air toxics from the production of charcoal in a simulated Missouri charcoal kiln

    SciTech Connect

    Lemieux, P.M.; Kariher, P.H.; Fairless, B.J.; Tapp, J.A.

    1998-11-01

    The paper gives results of experiments in a laboratory-scale charcoal kiln simulator to evaluate emissions of hazardous air pollutant from the production of charcoal in Missouri-type kilns. Fixed combustion gases were measured using continuous monitors. In addition, other pollutants, including methanol, volatile organic compounds, semivolatile organic compounds, and particle emission rates and size distributions were measured using various techniques. Emissions of all pollutants are reported in grams emitted per unit mass of initial wood converted to charcoal. Two burn conditions--slow and fast burn--were examined. High levels of methanol, benzene, and fine particulate were emitted from all tests. The estimated emissions from the fast burn conditions were significantly higher than those from the slow burn conditions.

  10. Charcoal deposition and redeposition in Elk Lake, Minnesota, USA

    USGS Publications Warehouse

    Platt, Bradbury J.

    1996-01-01

    Sedimentary charcoal, diatom and phytolith records of the past 1500 years at Elk Lake, Minnesota, in combination with sediment trap studies and a transect of surface sediment samples, document the mechanisms by which previously deposited charcoal is redeposited and finally buried in this lake. The frequent correspondence of high diatom concentrations and peaks of phytolith and charcoal fragments suggest that currents and turbulence related to lake circulation are responsible for winnowing charcoal and phytoliths from shallow water depositional sites to deeper areas of the lake. High diatom concentrations in the record relate to increased nutrient fluxes also supplied by circulation. Despite the fact that the watershed and area around Elk Lake has not been burned since AD 1922, charcoal continues to reach the profundal zone from littoral source areas in Elk Lake. The variable redeposition of within-lake charcoal requires evaluation before fire-history records can be related to global, regional or even local fire events.

  11. Auxiliary Propulsion Activities in Support of NASA's Exploration Initiative

    NASA Technical Reports Server (NTRS)

    Best, Philip J.; Unger, Ronald J.; Waits, David A.

    2005-01-01

    The Space Launch Initiative (SLI) procurement mechanism NRA8-30 initiated the Auxiliary Propulsion System/Main Propulsion System (APS/MPS) Project in 2001 to address technology gaps and development risks for non-toxic and cryogenic propellants for auxiliary propulsion applications. These applications include reaction control and orbital maneuvering engines, and storage, pressure control, and transfer technologies associated with on-orbit maintenance of cryogens. The project has successfully evolved over several years in response to changing requirements for re-usable launch vehicle technologies, general launch technology improvements, and, most recently, exploration technologies. Lessons learned based on actual hardware performance have also played a part in the project evolution to focus now on those technologies deemed specifically relevant to the Exploration Initiative. Formal relevance reviews held in the spring of 2004 resulted in authority for continuation of the Auxiliary Propulsion Project through Fiscal Year 2005 (FY05), and provided for a direct reporting path to the Exploration Systems Mission Directorate. The tasks determined to be relevant under the project were: continuation of the development, fabrication, and delivery of three 870 lbf thrust prototype LOX/ethanol reaction control engines; the fabrication, assembly, engine integration and testing of the Auxiliary Propulsion Test Bed at White Sands Test Facility; and the completion of FY04 cryogenic fluid management component and subsystem development tasks (mass gauging, pressure control, and liquid acquisition elements). This paper presents an overview of those tasks, their scope, expectations, and results to-date as carried forward into the Exploration Initiative.

  12. Charcoal in the soil and the Earth System

    NASA Astrophysics Data System (ADS)

    Scott, A. C.

    2012-04-01

    Charcoal occurs in the natural environment as either a result of wildfire or volcanic processes. Charcoal is one of a range of pyrolysis products that may be included in the term black carbon. This paper outlines aspects of charcoal formation (both natural and experimental) and briefly considers the taphonomic processes leading to a final assemblage. This is done using examples from recent fires and through experimentation. In particular, it is shown that the temperature of charcoal formation may influence the rate of subsequent decay. This has significance for biochar studies. While charcoal may remain near the place of it's formation and be buried in soils it still may be affected by physical and chemical changes that result in fragmentation and subsequent loss to the soil. Charcoal may also be washed out of the fire site by overland flow particularly if the rain occurs soon after the fire. Charcoal is abundant in many sedimentary rocks deposited in a wide range of environments, from terrestrial to marine. Charcoal has a long fossil record and is found in rock sequences from the late Silurian onwards. Charcoal provides evidence of the deep time history of wildfire. There is an intimate relationship between the history of oxygen in the atmosphere and periods of extensive wildfires. High atmospheric oxygen levels (around 30%) in the late Palaeozoic and Cretaceous had a profound effect on the Earth System. The use of charcoal for plant evolution studies, fire history studies, vegetation studies, anatomical studies, climate and atmospheric studies and the wider importance of charcoal for the Earth and Biological Sciences will be considered (Scott 2010, Glasspool and Scott in press). Charcoal is information-rich but yet is an under-utilized resource.

  13. paleofire: An R package to analyse sedimentary charcoal records from the Global Charcoal Database to reconstruct past biomass burning

    NASA Astrophysics Data System (ADS)

    Blarquez, Olivier; Vannière, Boris; Marlon, Jennifer R.; Daniau, Anne-Laure; Power, Mitchell J.; Brewer, Simon; Bartlein, Patrick J.

    2014-11-01

    We describe a new R package, paleofire, for analysis and synthesis of charcoal time series, such as those contained in the Global Charcoal Database (GCD), that are used to reconstruct paleofire activity (past biomass burning). paleofire is an initiative of the Global Paleofire Working Group core team (www.gpwg.org), whose aim is to encourage the use of sedimentary charcoal series to develop regional-to-global syntheses of paleofire activity, and to enhance access to the GCD data by providing a common research framework. Currently, paleofire features are organized into three different parts related to (i) site selection and charcoal series extraction from the GCD; (ii) charcoal data transformation; and (iii) charcoal series compositing and synthesis. We provide a technical description of paleofire and describe some new implementations such as the circular block bootstrap procedure. We tested the software using GCDv3 data from eastern North America, and provide examples of interpreting results of regional and global syntheses.

  14. Influences of charcoal and bamboo charcoal amendment on soil-fluoride fractions and bioaccumulation of fluoride in tea plants.

    PubMed

    Gao, Hongjian; Zhang, Zhengzhu; Wan, Xiaochun

    2012-10-01

    High levels of fluoride in tea plants pose a potential health risk to humans who drink tea. It has been demonstrated that tea plant fluoride is closely related to the available fluoride in soil. But approaches that could be used to regulate the availability of fluoride in soil have been rarely seen. This study aims to investigate how the addition of charcoal and bamboo charcoal affected soil fluoride availability and bioaccumulation of fluoride in tea plants. In a microcosm experiment, tea plants were grown in the tea garden soil mixed with different amounts of charcoal and bamboo charcoal [that is, 0.5, 1.0, 2.5, and 5.0 % (w/w)]. Soil-fluoride fractions and fluoride accumulated in tea plants were determined using the sequential extraction and ion selective electrode method. Obtained results showed that both charcoal and bamboo charcoal additions significantly enhanced the concentrations of Fe/Mn oxide-bound fluoride, but significantly reduced the concentrations of water-soluble and exchangeable fluoride (p < 0.05) in soil. Charcoal and bamboo charcoal additions also significantly decreased the amounts of fluoride in tea roots and tea leaves (p < 0.05). However, the additions of charcoal and bamboo charcoal had no impacts on the tea quality, as indexed by the concentrations of polysaccharides, polyphenols, amino acids, and caffeine in tea leaves. These results suggested that application of charcoal and bamboo charcoal may provide a useful method to reduce the availability of fluoride in soil and the subsequent fluoride uptake by tea plants.

  15. Charcoal as an alternative energy source. sub-project: briquetting of charcoal

    SciTech Connect

    Enstad, G.G.

    1982-02-02

    Charcoal briquettes have been studied both theoretically and experimentally. It appears most realistic to use binders in solution. Binders of this kind have been examined and the briquettes' mechanical properties measured. Most promising are borresperse, gum arabic, dynolex, and wood tar.

  16. 7 CFR 15b.37 - Auxiliary aids.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 1 2012-01-01 2012-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary...

  17. 7 CFR 15b.37 - Auxiliary aids.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 1 2014-01-01 2014-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary...

  18. 45 CFR 707.10 - Auxiliary aids.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 3 2011-10-01 2011-10-01 false Auxiliary aids. 707.10 Section 707.10 Public Welfare Regulations Relating to Public Welfare (Continued) COMMISSION ON CIVIL RIGHTS ENFORCEMENT OF... § 707.10 Auxiliary aids. (a) The Agency shall furnish appropriate auxiliary aids where necessary...

  19. 7 CFR 15b.37 - Auxiliary aids.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 1 2010-01-01 2010-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary...

  20. 7 CFR 15b.37 - Auxiliary aids.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 1 2013-01-01 2013-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary...

  1. 45 CFR 707.10 - Auxiliary aids.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 45 Public Welfare 3 2012-10-01 2012-10-01 false Auxiliary aids. 707.10 Section 707.10 Public Welfare Regulations Relating to Public Welfare (Continued) COMMISSION ON CIVIL RIGHTS ENFORCEMENT OF... § 707.10 Auxiliary aids. (a) The Agency shall furnish appropriate auxiliary aids where necessary...

  2. 7 CFR 15b.37 - Auxiliary aids.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 1 2011-01-01 2011-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary...

  3. 45 CFR 707.10 - Auxiliary aids.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 45 Public Welfare 3 2013-10-01 2013-10-01 false Auxiliary aids. 707.10 Section 707.10 Public Welfare Regulations Relating to Public Welfare (Continued) COMMISSION ON CIVIL RIGHTS ENFORCEMENT OF... § 707.10 Auxiliary aids. (a) The Agency shall furnish appropriate auxiliary aids where necessary...

  4. 45 CFR 707.10 - Auxiliary aids.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 45 Public Welfare 3 2010-10-01 2010-10-01 false Auxiliary aids. 707.10 Section 707.10 Public Welfare Regulations Relating to Public Welfare (Continued) COMMISSION ON CIVIL RIGHTS ENFORCEMENT OF... § 707.10 Auxiliary aids. (a) The Agency shall furnish appropriate auxiliary aids where necessary...

  5. 45 CFR 707.10 - Auxiliary aids.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 45 Public Welfare 3 2014-10-01 2014-10-01 false Auxiliary aids. 707.10 Section 707.10 Public Welfare Regulations Relating to Public Welfare (Continued) COMMISSION ON CIVIL RIGHTS ENFORCEMENT OF... § 707.10 Auxiliary aids. (a) The Agency shall furnish appropriate auxiliary aids where necessary...

  6. [Adsorption mechanism of furfural onto modified rice husk charcoals].

    PubMed

    Deng, Yong; Wang, Xianhua; Li, Yunchao; Shao, Jing'ai; Yang, Haiping; Chen, Hanping

    2015-10-01

    To evaluate the absorptive characteristics of furfural onto biomass charcoals derived from rice husk pyrolysis, we studied the information of the structure and surface chemistry properties of the rice husk charcoals modified by thermal treatment under nitrogen and carbon dioxide flow and adsorption mechanism of furfural. The modified samples are labeled as RH-N2 and RH-CO2. Fresh rice husk charcoal sample (RH-450) and modified samples were characterized by elemental analysis, nitrogen adsorption-desorption isotherms, Fourier-transform infrared spectroscopy and Boehm titration. The results show that fresh rice husk charcoal obtained at 450 degrees C had a large number of organic groups on its surface and poor pore structure. After the modification under nitrogen and carbon dioxide flow, oxygenic organics in rice husk charcoals decompose further, leading to the reduction of acidic functional groups on charcoals surface, and the increase of the pyrone structures of the basic groups. Meanwhile, pore structure was improved significantly and the surface area was increased, especially for the micropores. This resulted in the increase of π-π dispersion between the surfaces of rice husk charcoals and furfural molecular. With making comprehensive consideration of π-π dispersion and pore structure, the best removal efficiency of furfural was obtained by rice husk charcoal modified under carbon dioxide flow.

  7. Resistance to charcoal rot identified in ancestral soybean germplasm

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Charcoal rot, caused by the fungal pathogen Macrophomina phaseolina, is an economically important disease on soybean and other crops including maize, sorghum, and sunflowers. Without effective cultural or chemical options to control charcoal rot in soybean, finding sources of genetic resistance is o...

  8. Characterization of charcoals for helium cryopumping in fusion devices

    SciTech Connect

    Sedgley, D.W.; Tobin, A.G.; Batzer, T.H.; Call, W.R.

    1987-07-01

    The capability of charcoal as a sorbent for helium at cryogenic temperatures depends upon charcoal characteristics that are not well understood. Previous work by the authors has indicated that the charcoals' pumping capability for helium depends as much on their source as on their particle size distributions. To develop a correlation between the physical characteristics of charcoal and helium pumping performance, different charcoals based on wood, coal, coconut, and a petroleum by-product were obtained from commercial sources. They were bonded to an aluminum substrate, and cooled to liquid-helium temperatures in a vacuum chamber. The helium pumping speed at constant throughput versus quantity of helium absorbed was measured for each charcoal grade. Porosimetry measurements on each charcoal grade using nitrogen as the sorbent gas were made that included total surface area, adsorption and desorption isotherms, and pore area and pore volume distributions. Significant differences in helium pumping performance and in pore size distribution were observed. Comparisons are made between helium pumping performance and charcoal characteristics and a possible correlation is identified.

  9. Metal content of charcoal in mining-impacted wetland sediments.

    PubMed

    Baker, Leslie L; Strawn, Daniel G; Rember, William C; Sprenke, Kenneth F

    2011-01-01

    Charcoal is well known to accumulate contaminants, but its association with metals and other toxic elements in natural settings has not been well studied. Association of contaminants with charcoal in soil and sediment may affect their mobility, bioavailability, and fate in the environment. In this paper, natural wildfire charcoal samples collected from a wetland site that has been heavily contaminated by mine waste were analyzed for elemental contents and compared to the surrounding soil. Results showed that the charcoal particles were enriched over the host soils by factors of two to 40 times in all contaminant elements analyzed. Principal component analysis was carried out on the data to determine whether element enrichment patterns in the soil profile charcoal are related to those in the soils. The results suggest that manganese and zinc concentrations in charcoal are controlled by geochemical processes in the surrounding soil, whereas the concentrations of arsenic, lead, zinc, iron, phosphorus, and sulfur in charcoal are unrelated to those in the surrounding soil. This study shows evidence that charcoal in soils can have a distinct and important role in controlling contaminant speciation and fate in the environment.

  10. Evaluation of soybean genotypes for resistance to charcoal rot

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Charcoal rot caused by Macrophomina phaseolina causes more yield loss in soybean than most other diseases in the southern U.S.A. There are no commercial genotypes marketed as resistant to charcoal rot of soybean. Reactions of 27 maturity group (MG) III, 29 Early MG IV, 34 Late MG IV, and 59 MG V gen...

  11. EMISSIONS OF AIR TOXICS FROM A SIMULATED CHARCOAL KILN

    EPA Science Inventory

    The report gives results of experiments in a laboratory-scale charcoal kiln simulator to evaluate emissions of hazardous air pollutants from the production of charcoal in Missouri-type kilns. Fixed combustion gases were measured using continuous monitors. In Addition, other pollu...

  12. Characterization of charcoals for helium cryopumping in fusion devices

    NASA Astrophysics Data System (ADS)

    Sedgley, D. W.; Tobin, A. G.; Batzer, T. H.; Call, W. R.

    1987-07-01

    The capability of charcoal as a sorbent for helium at cryogenic temperatures depends upon charcoal characteristics that are not well understood. Previous work by the authors has indicated that the charcoals- pumping capability for helium depends as much on their source as on their particle size distributions. To develop a correlation between the physical characteristics of charcoal and helium pumping performance, different charcoals based on wood, coal, coconut, and a petroleum by-product were obtained from commercial sources. They were bonded to an aluminum substrate, and cooled to liquid-helium temperatures in a vacuum chamber. The helium pumping speed at constant throughput versus quantity of helium absorbed was measured for each charcoal grade. Porosimetry measurements on each charcoal grade using nitrogen as the sorbent gas were made that included total surface area, adsorption and desorption isotherms, and pore area and pore volume distributions. Significant differences in helium pumping performance and in pore size distribution were observed. Comparisons are made between helium pumping performance and charcoal characteristics and a possible correlation is identified.

  13. [Adsorption mechanism of furfural onto modified rice husk charcoals].

    PubMed

    Deng, Yong; Wang, Xianhua; Li, Yunchao; Shao, Jing'ai; Yang, Haiping; Chen, Hanping

    2015-10-01

    To evaluate the absorptive characteristics of furfural onto biomass charcoals derived from rice husk pyrolysis, we studied the information of the structure and surface chemistry properties of the rice husk charcoals modified by thermal treatment under nitrogen and carbon dioxide flow and adsorption mechanism of furfural. The modified samples are labeled as RH-N2 and RH-CO2. Fresh rice husk charcoal sample (RH-450) and modified samples were characterized by elemental analysis, nitrogen adsorption-desorption isotherms, Fourier-transform infrared spectroscopy and Boehm titration. The results show that fresh rice husk charcoal obtained at 450 degrees C had a large number of organic groups on its surface and poor pore structure. After the modification under nitrogen and carbon dioxide flow, oxygenic organics in rice husk charcoals decompose further, leading to the reduction of acidic functional groups on charcoals surface, and the increase of the pyrone structures of the basic groups. Meanwhile, pore structure was improved significantly and the surface area was increased, especially for the micropores. This resulted in the increase of π-π dispersion between the surfaces of rice husk charcoals and furfural molecular. With making comprehensive consideration of π-π dispersion and pore structure, the best removal efficiency of furfural was obtained by rice husk charcoal modified under carbon dioxide flow. PMID:26964338

  14. Auxiliary resonant DC tank converter

    DOEpatents

    Peng, Fang Z.

    2000-01-01

    An auxiliary resonant dc tank (ARDCT) converter is provided for achieving soft-switching in a power converter. An ARDCT circuit is coupled directly across a dc bus to the inverter to generate a resonant dc bus voltage, including upper and lower resonant capacitors connected in series as a resonant leg, first and second dc tank capacitors connected in series as a tank leg, and an auxiliary resonant circuit comprising a series combination of a resonant inductor and a pair of auxiliary switching devices. The ARDCT circuit further includes first clamping means for holding the resonant dc bus voltage to the dc tank voltage of the tank leg, and second clamping means for clamping the resonant dc bus voltage to zero during a resonant period. The ARDCT circuit resonantly brings the dc bus voltage to zero in order to provide a zero-voltage switching opportunity for the inverter, then quickly rebounds the dc bus voltage back to the dc tank voltage after the inverter changes state. The auxiliary switching devices are turned on and off under zero-current conditions. The ARDCT circuit only absorbs ripples of the inverter dc bus current, thus having less current stress. In addition, since the ARDCT circuit is coupled in parallel with the dc power supply and the inverter for merely assisting soft-switching of the inverter without participating in real dc power transmission and power conversion, malfunction and failure of the tank circuit will not affect the functional operation of the inverter; thus a highly reliable converter system is expected.

  15. Effects of historic charcoal burning on soil properties

    NASA Astrophysics Data System (ADS)

    Hirsch, Florian; Schneider, Anna; Raab, Alexandra; Raab, Thomas; Buras, Allan; van der Maaten, Ernst; Takla, Melanie; Räbiger, Christin; Cruz Garcia, Roberto; Wilmking, Martin

    2015-04-01

    In Northeastern Germany the production of ironware between the 16th and 19th century left behind a remarkable amount of charcoal kiln remains. At the study site in the forests north of Cottbus, Rubic Brunic Arenosols are developed on Weichselian glaciofluvial deposits. Remote sensing surveys, underpinned by archaeological studies, show that charcoal was gained from several thousand kilns. The round charcoal kiln remains with inner diameters up to 20 m are smooth platforms elevated a few decimeters higher than the surrounding area. The remaining mounds consist of an about 40 cm thick sheet containing residuals of the charcoal production process such as charcoal fragments, ash but also organic material covering the Rubic Brunic Arenosols. The charcoal kiln remains are distanced only up to 100 m from each other. For the 32 square kilometers large study site, the ground area covered by such charcoal production residuals is about 0.5 square kilometer, i.e. 1.5% of the study area. The charcoal kiln sites are a remarkable carbon accumulator on the sandy parent material. Against this background, we aim to characterize the effects of pyrolysis and the enrichment of carbon, induced by the charcoal production, on soil properties. Field work was done during archaeological rescue excavations on three charcoal kiln relicts having diameters of about 15 m. We applied 150 l of Brilliant Blue solution on six 1 square meter plots (three inside, three outside of the charcoal kiln mound) and afterwards trenched horizontal and vertical profiles for recording the staining patterns. Undisturbed soil samples to study soil micromorphology and further undisturbed samples for characterizing soil physical and hydraulic properties were taken. Outside of the charcoal kiln remain the Brilliant Blue solution drained within less than 10 minutes, whereas on the charcoal kiln remains the draining took between 20 and 40 minutes. Preliminary laboratory analyses underline the findings from the field and

  16. Fusion reactor high vacuum pumping: Charcoal cryosorber tritium exposure results

    SciTech Connect

    Sedgley, D.W.; Walthers, C.R.; Jenkins, E.M. )

    1991-01-01

    Recent experiments, have shown the practically of using activated charcoal (coconut charcoal) at 4{degrees}K to pump helium and hydrogen isotopes for a fusion reactor. Both speed and capacity for deuterium/helium and tritium/helium-3 mixtures were shown to be satisfactory. The long term effects of tritium on the charcoal/cement system developed by Grumman and LLNL were not known and a program was undertaken to see what, if any, effect long term tritium exposure has on the cryosorber. Several charcoal on aluminum test samples were subjected to six months exposure of tritium at approximately 77{degrees}K. The tritium was scanned several times with a residual gas analyzer and the speed-capacity performance of the samples was measured before, approximately half way through and after the exposure. Modest effects were noted which would not seriously restrict charcoal's use as a cryosorber for fusion reactor high vacuum pumping applications. 4 refs., 8 figs.

  17. Massive theophylline overdose. Rapid elimination by charcoal hemoperfusion.

    PubMed

    Ehlers, S M; Zaske, D E; Sawchuk, R J

    1978-08-01

    Shock, seizures, cardiac arrhythmias, and respiratory and cardiac arrests developed in a patient who ingested 8.5 g of theophylline. Her condition improved and her serum theophylline concentration decreased from 170 to 20 mg/ml during six hours of charcoal hemoperfusion. Theophylline was removed from the serum by the uncoated charcoal column, as shown by an extraction efficiency approaching 100%. The maximum charcoal clearance of theophylline was 163 ml/kg/hr. The average endogenous theophylline clearance in adults is 50 ml/kg/hr and that achieved with hemodialysis is only 24.3 ml/kg/hr. Uncoated charcoal efficiently removes theophylline from the serum; charcoal hemoperfusion should be considered in severe theophylline toxic reactions.

  18. Experimental and numerical study of steam gasification of a single charcoal particle

    SciTech Connect

    Mermoud, F.; Van de Steene, L.; Salvador, S.; Dirion, J.L.

    2006-04-15

    The present work deals with a study coupling experiments and modeling of charcoal gasification by steam at large particle scale. A reliable set of experiments was first established using a specially developed 'macro-TG' apparatus where a particle was suspended and continuously weighed during its gasification. The main control parameters of a fixed-bed process were modified separately: steam gasification of beech charcoal spheres of different diameters (10 to 30 mm) was studied at different temperatures (830 to 1030{sup o}C), different steam partial pressures (0.1 to 0.4 atm H{sub 2}O), and different gas velocities around the particle (0.09 to 0.30 m/s). Simulations with the particle model were performed for each case. Confrontations with experimental data indicate that the model predictions are both qualitatively and quantitatively satisfactory, with an accuracy of 7%, until 60% of conversion, despite the fact that the phenomena of reactive surface evolution and particle fracturing are not well understood. Anisotropy and peripheral fragmentation make the end of the process difficult to simulate. Finally, an analysis of the thermochemical situation is proposed: it is demonstrated that the usual homogeneous or shrinking core particle models are not satisfying and that only the assumption of thermal equilibrium between the particle and the surrounding gas is valid for a model at bed scale. (author)

  19. Influence of charcoal burning induced pyrolysis on soils

    NASA Astrophysics Data System (ADS)

    Hirsch, Florian; Nicolay, Alexander; Pötzsch, Bastian; Fritzsche, Marie; Raab, Alexandra; Raab, Thomas

    2014-05-01

    In Lusatia, Northeastern Germany, the production of ironware between the 16th and 19th century left behind a remarkable amount of charcoal kilns in the forests north of Cottbus. Remote sensing surveys, underpinned by archaeological studies, show that charcoal was gained around Cottbus from several thousand charcoal kilns which had internal diameters up to 20 m. For the study site with 35 km2 area, the until now prospected total ground area below the charcoal kilns which was potentially affected by the pyrolysis is about 0,5 km2. Historic data indicates that the pyrolysis in the charcoal kiln took up to several weeks, for the kilns with a diameter of 20 m about 20 days. To characterize the depth of thermal alteration of soils below the kiln our current focus is on the differentiation of the iron hydroxides by small-scale vertical analysis of soil profiles. The study site is situated 16 km northeast of Cottbus at the opencast mine Jänschwalde. Field work was done during the archaeological rescue excavation of a charcoal kiln in a 50 m long trench crossing an about 15 m wide charcoal kiln. One vertical profile outside the charcoal kiln and two vertical profiles below the charcoal kiln were chosen for analysis. The magnetic susceptibility was measured in situ on the undisturbed profile and ex situ on stepwise heated samples (105, 350, 550, 750 and 950°C). The total iron content was quantified ex situ by x-ray fluorescence. Our first results indicate a change in the magnetic susceptibility in the contact area of the mineral soil and the charcoal kiln. The influence of the pyrolysis on the soil is restricted to areas where the soil was not shielded against the heat by ash or organic material.

  20. Production of charcoal and activated carbon at elevated pressure

    SciTech Connect

    Dai, Xiangfeng; Norberg, N.; Antal, M.J. Jr.

    1995-12-31

    With its wide range of properties, charcoal finds many commercial applications for domestic cooking, refining of metals (steel, copper, bronze, nickel, aluminum and electro-manganese), production of chemicals (carbon disulfide, calcium carbide, silicon carbide, sodium cyanide, carbon black, fireworks, gaseous chemicals, absorbents, soil conditioners and pharmaceuticals), as well as production of activated carbon and synthesis gas. In 1991, the world production of charcoal was 22.8 million cubic meters (3.8 million metric tons) as shown in Table 1. Brazil is the world`s largest charcoal producer --- 5.9 million cubic meters or one million metric tons was produced in 1991, most of which is used in steel and iron industry. African countries produced 45% of the world total amount of charcoal, where 86% of the wood-based energy is for domestic use, most of which is inefficiently used. Charcoal is produced commercially in kilns with a 25% to 30% yield by mass on a 7 to 12 day operating cycle. Until recently, the highest yield of good quality charcoal reported in the literature was 38%. In this paper, and ASME code rated experimental system is presented for producing charcoal and activated carbon from biomass.

  1. Tubular bamboo charcoal for anode in microbial fuel cells

    NASA Astrophysics Data System (ADS)

    Zhang, Jun; Li, Jun; Ye, Dingding; Zhu, Xun; Liao, Qiang; Zhang, Biao

    2014-12-01

    The anode material plays a significant role in determining the performance of microbial fuel cells (MFCs). In this study, the bamboo charcoal tube is proposed as a novel anode substrate by carbonizing the natural bamboo. Its surface functional groups, biocompatibility and internal resistance are thoroughly investigated. Performance of the MFCs with a conventional graphite tube anode and a bamboo charcoal tube anode is also compared. The results indicate that the tubular bamboo charcoal anode exhibits advantages over the graphite tube anode in terms of rougher surface, superior biocompatibility and smaller total internal resistance. Moreover, the X-ray photoelectron spectroscopy (XPS) analysis for the bamboo charcoal reveals that the introduced C-N bonds facilitate the electron transfer between the biofilm and electrodes. As a result, the MFC with a bamboo charcoal tube anode achieves a 50% improvement in the maximum power density over the graphite tube case. Furthermore, scale-up of the bamboo charcoal tube anode is demonstrated by employing a bundle of tubular bamboo charcoal to reach higher power output.

  2. Recovery of datable charcoal beneath young lavas: lessons from Hawaii.

    USGS Publications Warehouse

    Lockwood, J.P.; Lipman, P.W.

    1980-01-01

    Field studies in Hawaii aimed at providing a radiocarbon-based chronology of prehistoric eruptive activity have led to a good understanding of the processes that govern the formation and preservation of charcoal beneath basaltic lava flows. Charcoal formation is a rate-dependent process controlled primarily by temperature and duration of heating, as well as by moisture content, density, and size of original woody material. Charcoal will form wherever wood buried by lava is raised to sufficiently high temperatures, but owing to the availability of oxygen it is commonly burned to ash soon after formation. Wherever oxygen circulation is sufficiently restricted, charcoal will be preserved, but where atmospheric oxygen circulates freely, charcoal will only be preserved at a lower temperature, below that required for charcoal ignition or catalytic oxidation. These factors cause carbonized wood, especially that derived from living roots, to be commonly preserved beneath all parts of pahoehoe flows (where oxygen circulation is restricted), but only under margins of aa. Practical guidelines are given for the recovery of datable charcoal beneath pahoehoe and aa. Although based on Hawaiian basaltic flows, the guidelines should be applicable to other areas. -Authors

  3. Generation rate of carbon monoxide from burning charcoal.

    PubMed

    Ojima, Jun

    2011-01-01

    Charcoal, often used as cooking fuel at some restaurants, generates a significant amount of carbon monoxide (CO) during its combustion. Every year in Japan, a number of cooks and waiters/waitresses are poisoned by CO emanating from burning charcoal. Although certain ventilation is necessary to prevent the accumulation of CO, it is difficult to estimate the proper ventilation requirement for CO because the generation rate of CO from burning charcoal has not been established. In this study, several charcoals were evaluated in terms of CO generation rate. Sample charcoals were burned in a cooking stove to generate exhaust gas. For each sample, four independent variables -- the mass of the sample, the flow rate of the exhaust gas, CO concentration in the exhaust gas and the combustion time of the sample -- were measured, and the CO generation rate was calculated. The generation rate of CO from the charcoal was shown to be 137-185 ml/min/kW. Theoretical ventilation requirements for charcoals to prevent CO poisoning are estimated to be 41.2-55.6 m(3)/h/kW.

  4. Bed bugs.

    PubMed

    Foulke, Galen T; Anderson, Bryan E

    2014-09-01

    The term bed bug is applied to 2 species of genus Cimex: lectularius describes the common or temperate bed bug, and hemipterus its tropical cousin. Cimex lectularius is aptly named; its genus and species derive from the Latin words for bug and bed, respectively. Though the tiny pest is receiving increased public attention and scrutiny, the bed bug is hardly a new problem. PMID:25577850

  5. Dentists' attitudes toward auxiliaries in Malaysia.

    PubMed

    Razak, I A; Lind, O P

    1994-03-01

    A postal questionnaire survey concerning dentists' attitudes toward auxiliaries in Malaysia resulted in a 73.1 per cent response rate. The result of the study indicates that whilst the majority of the dentists agreed that dental auxiliaries usually increase productivity and permit the dentists to devote more time for more challenging tasks, a majority felt uncomfortable to be held accountable for the performance of auxiliaries. A majority of the dentists agreed that dental auxiliaries work best under direct supervision. The perceived value of the auxiliaries was more positive among public sector dentists as compared to private practitioners. Almost three-quarters of the dentists were positive towards legalising properly trained auxiliaries to work in private practice performing mainly preventive procedures. The implications of these findings relative to existing regulations, mode of practice and the future prospect in the delivery of oral health care are discussed. PMID:8193979

  6. Reduction of the polycyclic aromatic hydrocarbon (PAH) content of charcoal smoke during grilling by charcoal preparation using high carbonisation and a preheating step.

    PubMed

    Chaemsai, Suriyapong; Kunanopparat, Thiranan; Srichumpuang, Jidapa; Nopharatana, Montira; Tangduangdee, Chairath; Siriwattanayotin, Suwit

    2016-01-01

    Charcoal-grilling may lead to contamination of food with carcinogenic polycyclic aromatic hydrocarbons (PAHs) during the grilling process. The objective of this work was to determine the effect of charcoal preparation on 16 USEPA priority PAHs in the smoke produced during the grilling process. Firstly, mangrove charcoal was prepared at carbonisation temperatures of 500, 750 and 1000 °C. The charcoal were then preheated by burning at 650 °C. This preheating step is usually used to prepare hot charcoal for the grilling process in the food industry. In this study, charcoal was preheated at different burning times at 5, 20 min and 5 h, at which time partial and whole charcoal glowed, and charcoal was completely burnt, respectively. Finally, PAHs in the smoke were collected and determined by GC/MS. The result showed that charcoal prepared at a carbonisation temperature of 500 °C had higher levels of PAHs released into the smoke. In contrast, charcoal produced at 750 and 1000 °C had lower PAHs released for all burning times. In addition, PAHs released for 5, 20 min and 5 h of burning time were about 19.9, 1.2 and 0.7 µg g(-1) dry charcoal for charcoal produced at 500 °C, and about 0.9-1.4, 0.8-1.2 and 0.15-0.3 µg g(-1) dry charcoal for charcoal produced at 750 and 1000 °C, respectively. Therefore, this research suggests that food grilled using charcoal carbonised at a high temperature of about 750 °C presents a lower risk of PAH contamination. In addition, in the preheating step, whole charcoal should fully glow in order to reduce the PAH content in charcoal before grilling.

  7. Formation of charcoal from biomass in a sealed reactor

    SciTech Connect

    Mok, W.S.L.; Antal, M.J. Jr. ); Szabo, P.; Varhegyi, G.; Zelei, B. )

    1992-04-01

    In this paper, samples o cellulose, hemicellulose, lignin, and nine species of whole biomass are pyrolyzed in sealed reactors. Very high charcoal yields (e.g., 40% from cellulose, 48% from Eucalyptus gummifera) were obtained. Higher sample loading (sample mass per unit reactor volume) increased charcoal yield and the associated exothermic heat release and lowered the reaction onset temperature. These effects were induced by the vapor-phase concentrations of the volatile products, and not the system pressure. Addition of water catalyzed the reaction and increased the char yield. These observations suggest that charcoal formation is autocatalyzed by water, an initial pyrolysis product. When whole biomass was used as a feedstock, higher charcoal yields were obtained from species with high lignin and/or low hemicellulose content.

  8. 24. Photocopy of photograph. VIEW OF CHARCOAL KILNS AND IRON ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    24. Photocopy of photograph. VIEW OF CHARCOAL KILNS AND IRON PLANT FROM SOUTH END OF BEACH, probably 1901. (From the Robert Teagle Private Collection, Port Townsend, WA) - Irondale Iron & Steel Plant, Port Townsend, Jefferson County, WA

  9. INTERIOR DETAIL, STOVE. SMALL CHARCOAL FIRES WERE LIT IN THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    INTERIOR DETAIL, STOVE. SMALL CHARCOAL FIRES WERE LIT IN THE DEPRESSIONS, WHICH WERE COVERED WITH IRON GRATES TO SUSPEND POTS OVER THE HEAT SOURCE - The Woodlands, 4000 Woodlands Avenue, Philadelphia, Philadelphia County, PA

  10. Relative efficacy and palatability of three activated charcoal mixtures.

    PubMed

    Navarro, R P; Navarro, K R; Krenzelok, E P

    1980-02-01

    The addition of bentonite with or without chocolate syrup improved the palatability of activated charcoal preparations. Furthermore, bentonite did not significantly reduce the efficacy of charcoal to absorb aspirin. Chocolate syrup reduced the adsorption effectiveness significantly. The mixtures have a reduced shelf-life when premixed with water. However, the dry ingredients can be pre-weighed and sealed in a large jar. Water can be added just prior to administration. PMID:7361450

  11. 47 CFR 74.6 - Licensing of broadcast auxiliary and low power auxiliary stations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Licensing of broadcast auxiliary and low power...) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO, AUXILIARY, SPECIAL BROADCAST AND OTHER PROGRAM DISTRIBUTIONAL SERVICES General; Rules Applicable to All Services in Part 74 § 74.6 Licensing of broadcast auxiliary...

  12. Chemical analysis and potential health risks of hookah charcoal.

    PubMed

    Elsayed, Yehya; Dalibalta, Sarah; Abu-Farha, Nedal

    2016-11-01

    Hookah (waterpipe) smoking is a very common practice that has spread globally. There is growing evidence on the hazardous consequences of smoking hookah, with studies indicating that its harmful effects are comparable to cigarette smoking if not worse. Charcoal is commonly used as a heating source for hookah smoke. Although charcoal briquettes are thought to be one of the major contributors to toxicity, their composition and impact on the smoke generated remains largely unidentified. This study aims to analyze the elemental composition of five different raw synthetic and natural charcoals by using Carbon-Hydrogen-Nitrogen (CHN) analysis, inductively coupled plasma (ICP), and scanning electron microscopy coupled with energy dispersive X-Ray spectrometry (SEM-EDS). Elemental analysis showed that the raw charcoals contain heavy metals such as zinc, iron, cadmium, vanadium, aluminum, lead, chromium, manganese and cobalt at concentrations similar, if not higher than, cigarettes. In addition, thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS) was used to analyze the chemical composition of the smoke produced from burning the charcoal samples. The smoke emitted from charcoal was found to be the source of numerous compounds which could be hazardous to health. A total of seven carcinogens, 39 central nervous system depressants and 31 respiratory irritants were identified.

  13. Charcoal versus LPG grilling: A carbon-footprint comparison

    SciTech Connect

    Johnson, Eric

    2009-11-15

    Undoubtedly, grilling is popular. Britons fire up their barbeques some 60 million times a year, consuming many thousands of tonnes of fuel. In milder climates consumption is even higher, and in the developing world, charcoal continues to be an essential cooking fuel. So it is worth comparing the carbon footprints of the two major grill types, charcoal and LPG, and that was the purpose of the study this paper documents. Charcoal and LPG grill systems were defined, and their carbon footprints were calculated for a base case and for some plausible variations to that base case. In the base case, the charcoal grilling footprint of 998 kg CO{sub 2}e is almost three times as large as that for LPG grilling, 349 kg CO{sub 2}e. The relationship is robust under all plausible sensitivities. The overwhelming factors are that as a fuel, LPG is dramatically more efficient than charcoal in its production and considerably more efficient in cooking. Secondary factors are: use of firelighters, which LPG does not need; LPG's use of a heavier, more complicated grill; and LPG's use of cylinders that charcoal does not need.

  14. Fluorine gettering by activated charcoal in a radiation environment

    SciTech Connect

    Felker, L.K.; Toth, L.M.

    1988-10-01

    Activated charcoal has been shown to be an effective gettering agent for the fluorine gas that is liberated in a radiation environment. Even though activated charcoal is a commonly used getter, little is known about the radiation stability of the fluorine-charcoal product. This work has shown that not only is the product stable in high gamma radiation fields, but also that radiation enhances the capacity of the charcoal for the fluorine. The most useful application of this work is with the Molten Salt Reactor Experiment (MSRE) fuel salt because the radioactive components (fission products and actinides) cause radiolytic damage to the solid LiF-BeF/sub 2/-ZrF/sub 4/-UF/sub 4/ (64.5, 30.3, 5.0, 0.13 mol %, respectively) resulting in the liberation of fluorine gas. This work has also demonstrated that the maximum damage to the fuel salt by approx.3 /times/ 10/sup 7/ R/h gamma radiation is approximately 2%, at which point the rate of recombination of fluorine with active metal sites within the salt lattice equals the rate of fluorine generation. The enhanced reactivity of the activated charcoal and radiation stability of the product ensures that the gettered fluorine will stay sequestered in the charcoal.

  15. Chemical analysis and potential health risks of hookah charcoal.

    PubMed

    Elsayed, Yehya; Dalibalta, Sarah; Abu-Farha, Nedal

    2016-11-01

    Hookah (waterpipe) smoking is a very common practice that has spread globally. There is growing evidence on the hazardous consequences of smoking hookah, with studies indicating that its harmful effects are comparable to cigarette smoking if not worse. Charcoal is commonly used as a heating source for hookah smoke. Although charcoal briquettes are thought to be one of the major contributors to toxicity, their composition and impact on the smoke generated remains largely unidentified. This study aims to analyze the elemental composition of five different raw synthetic and natural charcoals by using Carbon-Hydrogen-Nitrogen (CHN) analysis, inductively coupled plasma (ICP), and scanning electron microscopy coupled with energy dispersive X-Ray spectrometry (SEM-EDS). Elemental analysis showed that the raw charcoals contain heavy metals such as zinc, iron, cadmium, vanadium, aluminum, lead, chromium, manganese and cobalt at concentrations similar, if not higher than, cigarettes. In addition, thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS) was used to analyze the chemical composition of the smoke produced from burning the charcoal samples. The smoke emitted from charcoal was found to be the source of numerous compounds which could be hazardous to health. A total of seven carcinogens, 39 central nervous system depressants and 31 respiratory irritants were identified. PMID:27343945

  16. NASA electrothermal auxiliary propulsion technology

    NASA Technical Reports Server (NTRS)

    Stone, J. R.

    1986-01-01

    Electrothermal auxiliary propulsion systems provide high performance options which can have major mission benefits. There are several electrothermal concepts which offer a range of characteristics and benefits. Resistojets are the highest thrust to power option and are currently operational at mission average values of specific impulse, I sub sp approximately 295 sec. Long life, multipropellant resistojets are being developed for the space station, and resistojet technology advancements are being pursued to improve the I sub sp by more than 20 percent for resistojets used in satellite applications. Direct current arcjets have the potential of I sub sp over 400 sec with storable propellants and should provide over 1000 sec with hydrogen. Advanced concepts are being investigated to provide high power density options and possible growth to primary propulsion applications. Broad based experimental and analytical research and technology programs of NASA are summarized and recent significant advances are reviewed.

  17. Radiant vessel auxiliary cooling system

    DOEpatents

    Germer, John H.

    1987-01-01

    In a modular liquid-metal pool breeder reactor, a radiant vessel auxiliary cooling system is disclosed for removing the residual heat resulting from the shutdown of a reactor by a completely passive heat transfer system. A shell surrounds the reactor and containment vessel, separated from the containment vessel by an air passage. Natural circulation of air is provided by air vents at the lower and upper ends of the shell. Longitudinal, radial and inwardly extending fins extend from the shell into the air passage. The fins are heated by radiation from the containment vessel and convect the heat to the circulating air. Residual heat from the primary reactor vessel is transmitted from the reactor vessel through an inert gas plenum to a guard or containment vessel designed to contain any leaking coolant. The containment vessel is conventional and is surrounded by the shell.

  18. 46 CFR 63.25-1 - Small automatic auxiliary boilers.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Small automatic auxiliary boilers. 63.25-1 Section 63.25... AUXILIARY BOILERS Requirements for Specific Types of Automatic Auxiliary Boilers § 63.25-1 Small automatic auxiliary boilers. Small automatic auxiliary boilers defined as having heat-input ratings of 400,000...

  19. 46 CFR 63.25-1 - Small automatic auxiliary boilers.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Small automatic auxiliary boilers. 63.25-1 Section 63.25... AUXILIARY BOILERS Requirements for Specific Types of Automatic Auxiliary Boilers § 63.25-1 Small automatic auxiliary boilers. Small automatic auxiliary boilers defined as having heat-input ratings of 400,000...

  20. 46 CFR 63.25-1 - Small automatic auxiliary boilers.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Small automatic auxiliary boilers. 63.25-1 Section 63.25... AUXILIARY BOILERS Requirements for Specific Types of Automatic Auxiliary Boilers § 63.25-1 Small automatic auxiliary boilers. Small automatic auxiliary boilers defined as having heat-input ratings of 400,000...

  1. 46 CFR 63.25-1 - Small automatic auxiliary boilers.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Small automatic auxiliary boilers. 63.25-1 Section 63.25... AUXILIARY BOILERS Requirements for Specific Types of Automatic Auxiliary Boilers § 63.25-1 Small automatic auxiliary boilers. Small automatic auxiliary boilers defined as having heat-input ratings of 400,000...

  2. 46 CFR 63.25-1 - Small automatic auxiliary boilers.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Small automatic auxiliary boilers. 63.25-1 Section 63.25... AUXILIARY BOILERS Requirements for Specific Types of Automatic Auxiliary Boilers § 63.25-1 Small automatic auxiliary boilers. Small automatic auxiliary boilers defined as having heat-input ratings of 400,000...

  3. 33 CFR 5.48 - Auxiliary Patrol Boat ensign.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Auxiliary Patrol Boat ensign. 5... COAST GUARD AUXILIARY § 5.48 Auxiliary Patrol Boat ensign. (a) The Coast Guard Auxiliary Patrol Boat... this part. (b) The field of the Auxiliary Patrol Boat ensign is white. A medium blue (Coast Guard...

  4. 33 CFR 5.48 - Auxiliary Patrol Boat ensign.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Auxiliary Patrol Boat ensign. 5... COAST GUARD AUXILIARY § 5.48 Auxiliary Patrol Boat ensign. (a) The Coast Guard Auxiliary Patrol Boat... this part. (b) The field of the Auxiliary Patrol Boat ensign is white. A medium blue (Coast Guard...

  5. 47 CFR 97.201 - Auxiliary station.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES AMATEUR RADIO SERVICE Special Operations § 97.201 Auxiliary station. (a) Any amateur station licensed to a holder of a Technician, General, Advanced or Amateur Extra Class operator license may be an auxiliary station. A...

  6. 47 CFR 97.201 - Auxiliary station.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES AMATEUR RADIO SERVICE Special Operations § 97.201 Auxiliary station. (a) Any amateur station licensed to a holder of a Technician, General, Advanced or Amateur Extra Class operator license may be an auxiliary station. A...

  7. 47 CFR 97.201 - Auxiliary station.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES AMATEUR RADIO SERVICE Special Operations § 97.201 Auxiliary station. (a) Any amateur station licensed to a holder of a Technician, General, Advanced or Amateur Extra Class operator license may be an auxiliary station. A...

  8. 47 CFR 97.201 - Auxiliary station.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES AMATEUR RADIO SERVICE Special Operations § 97.201 Auxiliary station. (a) Any amateur station licensed to a holder of a Technician, General, Advanced or Amateur Extra Class operator license may be an auxiliary station. A...

  9. In vitro study on fluoxetine adsorption onto charcoal using potentiometry.

    PubMed

    Atta-Politou, J; Skopelitis, I; Apatsidis, I; Koupparis, M

    2001-01-01

    This in vitro investigation was performed to study the adsorption rate constant as well as the adsorption characteristics of fluoxetine (F) to activated charcoal and its commercial formulation Carbomix powder in simulated gastric (pH 1.2) fluid environment. Ion-selective electrode (ISE) potentiometry, based on the selective, direct and continuous monitoring of F with an F-ISE constructed in our laboratory was used. The method used in the kinetic experiments consists of the rapid addition of a slurry containing the charcoal into the drug solution under stirring and continuous recording of the F-ISE potential until the establishment of equilibrium. The free ionized drug concentration at appropriate time intervals was calculated from the recorded adsorption curve and the apparent adsorption rate constant was estimated assuming pseudo first order kinetics. Within run R.S.D. of the estimates ranged from 0.24 to 11.5%, while between run R.S.D. (n=3-4) ranged from 0.90 to 13.8%. A linear relationship was found between the apparent adsorption rate constants and the amount of charcoal used with slopes (+/-S.D.) for activated charcoal and Carbomix equal to 1.14(+/-0.21) and 0.146(+/-0.009) s(-1)g(-1), respectively. Successive additions of microvolumes of F solution were made into a charcoal slurry with measurement of the F-ISE potential at equilibrium. The maximum adsorption capacity values (+/-S.D.) of activated charcoal and Carbomix were 254.8+/-1.8 and 405+/-41 mg/g, respectively while the affinity constant values (+/-S.D.) were 45.6+/-2.2 and 55.5+/-2.9 l/g, respectively. The adsorption of F to charcoals was rapid and for amounts of charcoal 10 times greater than the amount of the drug, 95% of F was adsorbed within the first 5 min. Relative to the toxic and lethal doses in cases of F intoxications, both types of charcoals tested adsorbed effectively F at gastric pH. Carbomix can be considered as appropriate charcoal formulation for medical treatment in cases of F

  10. Adsorption effects of activated charcoal on metaldehyde toxicity in rats.

    PubMed

    Shintani, S; Goto, K; Endo, Y; Iwamoto, C; Ohata, K

    1999-02-01

    Metaldehyde has been widely used as a main ingredient of solid fuel for making fire and slug baits in Japan. It is also marketed as a color flame tablet for party goods (ENGELFIRE). Consequently, children have been poisoned by eating such tablets which they mistook for candy. As a result, poison information center calls are increasing. According to POISINDEX, the treatment for metaldehyde poisoning consists in prevention of adsorption by activated charcoal, seizure control and airway protection. However, the optimum dose of charcoal is not established. We studied the quantitative adsorption capacity of activated charcoal for acute oral toxicity of metaldehyde in rats. In vivo toxicity and absorption tests for metaldehyde in Wister rats were done. The detoxifying effect of activated charcoal on metaldehyde toxicity and inhibition of metaldehyde absorption were investigated. Ratios used of po activated charcoal given 30 min after dosing to 400 mg metaldehyde/kg po were 5:1, 2:1, 1:1, 0.5:1. Serum metaldehyde was determined by gas chromatography in the control group (no charcoal) and the various experimental groups. Metaldehyde mortality was completely prevented at the ratio of 5:1. Gastrointestinal absorption of metaldehyde was reduced significantly by 45.3% in comparison to the control rats. There was no acetaldehyde detected in the serum of the metaldehyde-dosed rats. Metaldehyde poisoning may be prevented by early po administration of activated charcoal in a ratio of > 5:1 compared to metaldehyde. The theory that acetaldehyde is the primary toxic agent in metaldehyde poisoning should be re-evaluated.

  11. Effects of charcoal kiln saunas (Jjimjilbang) on psychological states.

    PubMed

    Hayasaka, Shinya; Nakamura, Yosikazu; Kajii, Eiji; Ide, Masahiro; Shibata, Yosuke; Noda, Tatsuya; Murata, Chiyoe; Nagata, Katsutaro; Ojima, Toshiyuki

    2008-05-01

    This uncontrolled intervention study explored the effects of sauna bathing utilizing residual heat from charcoal kilns (charcoal kiln saunas) on psychological states. Forty-five volunteers (24 males and 21 females; mean age 51.9 years (S.D. 15.7) visiting a bamboo charcoal kiln in Japan participated in the study. They completed a shortened version of the Profile of Mood States (POMS) and State-Trait Anxiety Inventory (STAI) before and after charcoal kiln sauna bathing in order to determine mood and anxiety states. Six factors relating to mood were measured using the POMS: Tension-Anxiety, Depression-Dejection, Anger-Hostility, Vigor, Fatigue, and Confusion. The two anxiety concepts of state anxiety and trait anxiety were also measured. Changes in psychological states before and after sauna bathing were then determined. All mood scales and both manifest anxiety measures were improved after sauna bathing. Charcoal kiln sauna bathing appears to improve mood and decrease anxiety. It is a limitation of this study that this was a descriptive prospective and an uncontrolled intervention study. Further investigation of the improvement of trait anxiety is required.

  12. Auxiliary propulsion system flight package

    NASA Technical Reports Server (NTRS)

    Collett, C. R.

    1987-01-01

    Hughes Aircraft Company developed qualified and integrated flight, a flight test Ion Auxiliary Propulsion System (IAPS), on an Air Force technology satellite. The IAPS Flight Package consists of two identical Thruster Subsystems and a Diagnostic Subsystem. Each thruster subsystem (TSS) is comprised of an 8-cm ion Thruster-Gimbal-Beam Shield Unit (TGBSU); Power Electronics Unit; Digital Controller and Interface Unit (DCIU); and Propellant Tank, Valve and Feed Unit (PTVFU) plus the requisite cables. The Diagnostic Subsystem (DSS) includes four types of sensors for measuring the effect of the ion thrusters on the spacecraft and the surrounding plasma. Flight qualifications of IAPS, prior to installation on the spacecraft, consisted of performance, vibration and thermal-vacuum testing at the unit level, and thermal-vacuum testing at the subsystem level. Mutual compatibility between IAPS and the host spacecraft was demonstrated during a series of performance and environmental tests after the IAPS Flight Package was installed on the spacecraft. After a spacecraft acoustic test, performance of the ion thrusters was reverified by removing the TGBSUs for a thorough performance test at Hughes Research Laboratories (HRL). The TGBSUs were then reinstalled on the spacecraft. The IAPS Flight Package is ready for flight testing when Shuttle flights are resumed.

  13. Tuneable Auxiliary Control Mechanisms For RUM Actuators

    NASA Technical Reports Server (NTRS)

    Polites, Michael E.; Alhorn, Dean C.

    1995-01-01

    Tuneable auxiliary control mechanisms for rotating unbalanced-mass (RUM) actuators used to maximize scan amplitudes and/or minimize power consumption during changing conditions. This type of mechanism more sophisticated version of type of mechanism described in "Auxiliary Control Mechanisms for RUM Actuators" (MFS-28817). Torsional stiffness of torsionally flexible coupling made adjustable on command. Torsionally flexible coupling in tuneable version of auxiliary control mechanism adjustable by use of stepping-motor-driven worm-gear mechanism that varies bending length of flexible blade.

  14. Electric auxiliary power unit for Shuttle evolution

    NASA Technical Reports Server (NTRS)

    Meyer, Doug; Weber, Kent; Scott, Walter

    1989-01-01

    The Space Shuttle Orbiter currently uses three hydrazine fueled auxiliary power units (APUs) to provide hydraulic power for the vehicle aerodynamic surface controls, main engine thrust vector control, landing gear, steering, and brakes. Electric auxiliary power units have been proposed as possible replacements to the hydrazine auxiliary power units. Along with the potential advantages, this paper describes an Electric APU configuration and addresses the technical issues and risks associated with the subsystem components. Additionally, characteristics of an Electric APU compared to the existing APU and the direction of future study with respect to the Electric APU is suggested.

  15. H(curl) Auxiliary Mesh Preconditioning

    SciTech Connect

    Kolev, T V; Pasciak, J E; Vassilevski, P S

    2006-08-31

    This paper analyzes a two-level preconditioning scheme for H(curl) bilinear forms. The scheme utilizes an auxiliary problem on a related mesh that is more amenable for constructing optimal order multigrid methods. More specifically, we analyze the case when the auxiliary mesh only approximately covers the original domain. The latter assumption is important since it allows for easy construction of nested multilevel spaces on regular auxiliary meshes. Numerical experiments in both two and three space dimensions illustrate the optimal performance of the method.

  16. Pore structure of the activated coconut shell charcoal carbon

    NASA Astrophysics Data System (ADS)

    Budi, E.; Nasbey, H.; Yuniarti, B. D. P.; Nurmayatri, Y.; Fahdiana, J.; Budi, A. S.

    2014-09-01

    The development of activated carbon from coconut shell charcoal has been investigated by using physical method to determine the influence of activation parameters in term of temperature, argon gas pressure and time period on the pore structure of the activated carbon. The coconut shell charcoal was produced by pyrolisis process at temperature of about 75 - 150 °C for 6 hours. The charcoal was activated at various temperature (532, 700 and 868 °C), argon gas pressure (6.59, 15 and 23.4 kgf/cm2) and time period of (10, 60 and 120 minutes). The results showed that the pores size were reduced and distributed uniformly as the activation parameters are increased.

  17. Application of activated charcoal radon collectors in high humidity environments.

    PubMed

    Iimoto, Takeshi; Tokonami, Shinji; Morishita, Yasuaki; Kosako, Toshiso

    2005-01-01

    Most commercially based activated charcoal radon collectors were designed for use in indoor environments. However, at present, they are often used for research in radon surveys in unique environments, such as in the bathrooms, underground areas, mines, caves and tunnels. In these environments, the relative humidity would be around 100%, and a change in the sensitivity of cpm(Bq m(-3))(-1)(radon) would occur. For this study, the reduction in the sensitivity of activated charcoal radon collector due to environmental humidity was investigated, and the data correction was discussed. Here, ST-100 (Pico-Rad) was selected as an example of a familiar activated charcoal radon collector. According to our performance test, the humidity of 90% (20 degrees C) resulted in a 15% reduction of the sensitivity for 24 h collection. The ST-100 user should discuss the necessity of data correction by comparing the change of sensitivity with other levels of estimation errors.

  18. Auxiliary circuit enables automatic monitoring of EKG'S

    NASA Technical Reports Server (NTRS)

    1965-01-01

    Auxiliary circuits allow direct, automatic monitoring of electrocardiograms by digital computers. One noiseless square-wave output signal for each trigger pulse from an electrocardiogram preamplifier is produced. The circuit also permits automatic processing of cardiovascular data from analog tapes.

  19. Evaluation of charcoal sorbents for helium cryopumping in fusion reactors

    SciTech Connect

    Tobin, A.G.; Sedgley, D.W.; Batzer, T.H.; Call, W.R.

    1987-01-01

    Improved methods for cryopumping helium were developed for application to fusion reactors where high helium generation rates are expected. In this study, small coconut charcoal granules were utilized as the sorbent, and braze alloys and low temperature curing cements were used as the bonding agents for attachment to a copper support structure. Problems of scale-up of the bonding agent to a 40 cm diam panel were also investigated. Our results indicate that acceptable helium pumping performance of braze bonded and cement bonded charcoals can be achieved over the range of operating conditions expected in fusion reactors.

  20. Can Charcoal Provide Information About Fire Effects and Fire Severity?

    NASA Astrophysics Data System (ADS)

    Belcher, Claire; Hudpsith, Victoria; Doerr, Stefan; Santin, Cristina

    2016-04-01

    Building an understanding of the impact of a wildfire is critical to the management of ecosystems. Aspects of fire severity such as the amount of soil heating, can relate to post-fire ecosystem recovery. Yet, there is no quantitative measure of this in current post-burn fire severity assessments, which are mostly qualitative ground-based visual assessments of organic matter loss, and as such can be subjective and variable between ecosystems. In order to develop a unifying fire severity assessment we explore the use of charcoal produced during a wildfire, as a tool. Charcoal has been suggested to retain some information about the nature of the fire in which it was created and one such physical property of charcoal that can be measured post-fire is its ability to reflect light when studied under oil using reflectance microscopy. The amount of light reflected varies between charcoals and is thought to be explained by the differential ordering of graphite-like phases within the char however, to what aspects of a fire's nature this alteration pertains is unknown. We have explored the formation of charcoal reflectance in 1) laboratory-based experiments using an iCone calorimeter and in 2) experimental forest scale and natural wildland fires occurring in Canada in spring 2015. In our laboratory experiments we assessed the formation and evolution of charcoal reflectance during pre-ignition heating, peak fire intensity through to the end of flaming and the transition to oxidative/smoldering heating regimes. In the prescribed and natural wildland fires we positioned the same woods used in our laboratory experiments, rigged with thermocouples in the path of oncoming fires in order to assess the resulting charcoal reflectance in response to the heating regime imposed by the fire on the samples. In this presentation we will outline our approach, findings and discuss the potential for charcoal reflectance to provide a tool in post-fire assessments seeking to determine levels of

  1. Charcoal kiln relicts - a favorable site for tree growth?

    NASA Astrophysics Data System (ADS)

    Buras, Allan; Hirsch, Florian; van der Maaten, Ernst; Takla, Melanie; Räbiger, Christin; Cruz Garcia, Roberto; Schneider, Anna; Raab, Alexandra; Raab, Thomas; Wilmking, Martin

    2015-04-01

    Soils with incompletely combusted organic material (aka 'black carbon') are considered fertile for plant growth. Considerable enrichment of soils with black carbon is known from Chernozems, from anthropogenic induced altering of soils like the 'Terra Preta' in South America (e.g. Glaser, 2001), and from charcoal kiln relicts. Recent studies have reported a high spatial frequency of charcoal kiln relicts in the Northeastern German lowlands (Raab et al., 2015), which today are often overgrown by forest plantations. In this context the question arises whether these sites are favorable for tree growth. Here we compare the performance of 22 Pinus sylvestris individuals - a commonly used tree species in forestry - growing on charcoal kiln relicts with 22 control trees. Growth performance (height growth and diameter growth) of the trees was determined using dendrochronological techniques, i.e. standard ring-width measurements were undertaken on each two cores per tree and tree height was measured in the field. Several other wood properties such as annual wood density, average resin content, as well as wood chemistry were analyzed. Our results indicate that trees growing on charcoal kiln relicts grow significantly less and have a significantly lower wood density in comparison with control trees. Specific chemical components such as Manganese as well as resin contents were significantly higher in kiln trees. These results highlight that tree growth on charcoal kiln relicts is actually hampered instead of enhanced. Possibly this is a combined effect of differing physical soil properties which alter soil water accessibility for plants and differing chemical soil properties which may negatively affect tree growth either if toxic limits are surpassed or if soil nutrient availability is decreased. Additional soil analyses with respect to soil texture and soil chemistry shall reveal further insight into this hypothesis. Given the frequent distribution of charcoal kiln relicts in

  2. Enhancing methane production during the anaerobic digestion of crude glycerol using Japanese cedar charcoal.

    PubMed

    Watanabe, Ryoya; Tada, Chika; Baba, Yasunori; Fukuda, Yasuhiro; Nakai, Yutaka

    2013-12-01

    The use of Japanese cedar charcoal as a support material for microbial attachment could enhance methane production during anaerobic digestion of crude glycerol and wastewater sludge. Methane yield from a charcoal-containing reactor was approximately 1.6 times higher than that from a reactor without charcoal, and methane production was stable over 50 days when the loading rate was 2.17 g chemical oxygen demand (COD) L(-1) d(-1). Examination of microbial communities on the charcoal revealed the presence of Uncultured Desulfovibrio sp. clone V29 and Pelobacter seleniigenes, known as 1,3-propandiol degraders. Hydrogenotrophic methanogens were also detected in the archaeal community on the charcoal. Methanosaeta, Methanoregula, and Methanocellus were present in the charcoal-containing reactor. The concentration of propionate in the charcoal-containing reactor was also lower than that in the control reactor. These results suggest that propionate degradation was enhanced by the consumption of hydrogen by hydrogenotrophic methanogens on the charcoal.

  3. 46 CFR 58.01-35 - Main propulsion auxiliary machinery.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the...

  4. 46 CFR 58.01-35 - Main propulsion auxiliary machinery.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the...

  5. 46 CFR 58.01-35 - Main propulsion auxiliary machinery.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the...

  6. 46 CFR 58.01-35 - Main propulsion auxiliary machinery.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the...

  7. 30 CFR 75.331 - Auxiliary fans and tubing.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Auxiliary fans and tubing. 75.331 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.331 Auxiliary fans and tubing. (a) When auxiliary fans and tubing are used for face ventilation, each auxiliary fan shall be—...

  8. 30 CFR 75.331 - Auxiliary fans and tubing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Auxiliary fans and tubing. 75.331 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.331 Auxiliary fans and tubing. (a) When auxiliary fans and tubing are used for face ventilation, each auxiliary fan shall be—...

  9. 30 CFR 75.331 - Auxiliary fans and tubing.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Auxiliary fans and tubing. 75.331 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.331 Auxiliary fans and tubing. (a) When auxiliary fans and tubing are used for face ventilation, each auxiliary fan shall be—...

  10. 30 CFR 75.331 - Auxiliary fans and tubing.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Auxiliary fans and tubing. 75.331 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.331 Auxiliary fans and tubing. (a) When auxiliary fans and tubing are used for face ventilation, each auxiliary fan shall be—...

  11. 30 CFR 75.331 - Auxiliary fans and tubing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Auxiliary fans and tubing. 75.331 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.331 Auxiliary fans and tubing. (a) When auxiliary fans and tubing are used for face ventilation, each auxiliary fan shall be—...

  12. 46 CFR 58.01-35 - Main propulsion auxiliary machinery.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the...

  13. Air quality index from charcoal production sites, carboxyheamoglobin and lung function among occupationally exposed charcoal workers in South Western Nigeria.

    PubMed

    Olujimi, O O; Ana, G R E E; Ogunseye, O O; Fabunmi, V T

    2016-01-01

    Charcoal production is often accompanied with gaseous and particulate emission into the atmosphere and occupationally exposed workers could be affected. This cross sectional comparative study was carried out to assess the levels of carbon monoxide (CO), carbon dioxide (CO2), sulphur dioxide (SO2), nitrogen dioxide (NO2) and particulate matter (PM2.5) generated during the phases of charcoal production and their relationship with certain biomarkers among charcoal workers (subjects) and non-charcoal workers (controls) such as carboxyhaemoglobin (COHb), forced expiratory volume in the first second of expiration (FEV1), peak expiratory flow rate (PEFR) and body mass index (BMI) in Igbo-Ora, Oyo State and Alabata, Ogun State, which are two of the major hubs of charcoal production in South Western Nigeria. Four communities in Igbo-Ora and six communities in Alabata were purposively selected and levels of pollutant gases were assessed using appropriate gas meters, PM2.5 was assessed with Thermo Scientific MIE pDR-1500, FEV1 and PEFR were measured with Piko-1 spirometer while COHb was assessed using non-invasive pulse CO-oximeter (Rad 57). Data were statistically analyzed and results were compared with recommended guidelines. The mean FEV1, PEFR, COHb and BMI for subjects and controls were 2.35 ± 0.73 and 2.69 ± 0.56, 253.72 ± 103.45 and 330.02 ± 94.61 (p < 0.01), 13.28 ± 3.91 and 8.50 ± 3.68 (p < 0.01) and 21.97 ± 2.19 and 23.36 ± 3.74 (p < 0.05) respectively. There was a statistically significant difference between actual and expected values of FEV1 (p < 0.01) and PEFR (p < 0.01) among charcoal workers. There existed a positive correlation between CO and COHb while FEV1 and PEFR correlated negatively with PM2.5. The study showed that charcoal workers are exposed to high levels of CO and PM2.5, contributing to lowered respiratory functions for FEV1 and PEFR and high levels of COHb compared to the control group. Routine respiratory and

  14. Air quality index from charcoal production sites, carboxyheamoglobin and lung function among occupationally exposed charcoal workers in South Western Nigeria.

    PubMed

    Olujimi, O O; Ana, G R E E; Ogunseye, O O; Fabunmi, V T

    2016-01-01

    Charcoal production is often accompanied with gaseous and particulate emission into the atmosphere and occupationally exposed workers could be affected. This cross sectional comparative study was carried out to assess the levels of carbon monoxide (CO), carbon dioxide (CO2), sulphur dioxide (SO2), nitrogen dioxide (NO2) and particulate matter (PM2.5) generated during the phases of charcoal production and their relationship with certain biomarkers among charcoal workers (subjects) and non-charcoal workers (controls) such as carboxyhaemoglobin (COHb), forced expiratory volume in the first second of expiration (FEV1), peak expiratory flow rate (PEFR) and body mass index (BMI) in Igbo-Ora, Oyo State and Alabata, Ogun State, which are two of the major hubs of charcoal production in South Western Nigeria. Four communities in Igbo-Ora and six communities in Alabata were purposively selected and levels of pollutant gases were assessed using appropriate gas meters, PM2.5 was assessed with Thermo Scientific MIE pDR-1500, FEV1 and PEFR were measured with Piko-1 spirometer while COHb was assessed using non-invasive pulse CO-oximeter (Rad 57). Data were statistically analyzed and results were compared with recommended guidelines. The mean FEV1, PEFR, COHb and BMI for subjects and controls were 2.35 ± 0.73 and 2.69 ± 0.56, 253.72 ± 103.45 and 330.02 ± 94.61 (p < 0.01), 13.28 ± 3.91 and 8.50 ± 3.68 (p < 0.01) and 21.97 ± 2.19 and 23.36 ± 3.74 (p < 0.05) respectively. There was a statistically significant difference between actual and expected values of FEV1 (p < 0.01) and PEFR (p < 0.01) among charcoal workers. There existed a positive correlation between CO and COHb while FEV1 and PEFR correlated negatively with PM2.5. The study showed that charcoal workers are exposed to high levels of CO and PM2.5, contributing to lowered respiratory functions for FEV1 and PEFR and high levels of COHb compared to the control group. Routine respiratory and

  15. Research report: Charcoal type used for hookah smoking influences CO production.

    PubMed

    Medford, Marlon A; Gasier, Heath G; Hexdall, Eric; Moffat, Andrew D; Freiberger, John J; Moon, Richard E

    2015-01-01

    A hookah smoker who was treated for severe carbon monoxide poisoning with hyperbaric oxygen reported using a different type of charcoal prior to hospital admission, i.e., quick-light charcoal. This finding led to a study aimed at determining whether CO production differs between charcoals commonly used for hookah smoking, natural and quick-light. Our hypothesis was that quick-light charcoal produces significantly more CO than natural charcoal. A medium-sized hookah, activated charcoal filter, calibrated syringe, CO gas analyzer and infrared thermometer were assembled in series. A single 9-10 g briquette of either natural or quick-light charcoal was placed atop the hookah bowl and ignited. CO output (ppm) and temperature (degrees C) were measured in three-minute intervals over 90 minutes. The mean CO levels produced by quick-light charcoal over 90 minutes was significantly higher (3728 ± 2028) compared to natural charcoal (1730 ± 501 ppm, p = 0.016). However, the temperature was significantly greater when burning natural charcoal (292 ± 87) compared to quick-light charcoal (247 ± 92 degrees C, p = 0.013). The high levels of CO produced when using quick-light charcoals may be contributing to the increase in reported hospital admissions for severe CO poisoning. PMID:26403022

  16. Research report: Charcoal type used for hookah smoking influences CO production.

    PubMed

    Medford, Marlon A; Gasier, Heath G; Hexdall, Eric; Moffat, Andrew D; Freiberger, John J; Moon, Richard E

    2015-01-01

    A hookah smoker who was treated for severe carbon monoxide poisoning with hyperbaric oxygen reported using a different type of charcoal prior to hospital admission, i.e., quick-light charcoal. This finding led to a study aimed at determining whether CO production differs between charcoals commonly used for hookah smoking, natural and quick-light. Our hypothesis was that quick-light charcoal produces significantly more CO than natural charcoal. A medium-sized hookah, activated charcoal filter, calibrated syringe, CO gas analyzer and infrared thermometer were assembled in series. A single 9-10 g briquette of either natural or quick-light charcoal was placed atop the hookah bowl and ignited. CO output (ppm) and temperature (degrees C) were measured in three-minute intervals over 90 minutes. The mean CO levels produced by quick-light charcoal over 90 minutes was significantly higher (3728 ± 2028) compared to natural charcoal (1730 ± 501 ppm, p = 0.016). However, the temperature was significantly greater when burning natural charcoal (292 ± 87) compared to quick-light charcoal (247 ± 92 degrees C, p = 0.013). The high levels of CO produced when using quick-light charcoals may be contributing to the increase in reported hospital admissions for severe CO poisoning.

  17. 40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment... MANUFACTURING POINT SOURCE CATEGORY Char and Charcoal Briquets Subcategory § 454.10 Applicability; description of the manufacture of char and charcoal briquets subcategory. The provisions of this subpart...

  18. 40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment... MANUFACTURING POINT SOURCE CATEGORY Char and Charcoal Briquets Subcategory § 454.10 Applicability; description of the manufacture of char and charcoal briquets subcategory. The provisions of this subpart...

  19. 40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment... MANUFACTURING POINT SOURCE CATEGORY Char and Charcoal Briquets Subcategory § 454.10 Applicability; description of the manufacture of char and charcoal briquets subcategory. The provisions of this subpart...

  20. 40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment... MANUFACTURING POINT SOURCE CATEGORY Char and Charcoal Briquets Subcategory § 454.10 Applicability; description of the manufacture of char and charcoal briquets subcategory. The provisions of this subpart...

  1. URINARY BIOMARKERS IN CHARCOAL WORKERS EXPOSED TO WOOD SMOKE IN BAHIA STATE, BRAZIL

    EPA Science Inventory

    Charcoal is an important source of energy for domestic and industrial use in many countries. In Brazil, the largest producer of charcoal in the world, approximately 350,000 workers are linked to the production and transportation of charcoal. In order to evaluate the occupationa...

  2. EMISSIONS OF AIR TOXICS FROM A SIMULATED CHARCOAL KILN EQUIPPED WITH AN AFTERBURNER

    EPA Science Inventory

    The report discusses emissions of air toxics from a simulated charcoal kiln equipped with an afterburner. A laboratory-scale simulator was constructed and tested to determine if it could be used to produce charcoal that was similar to that produced in Missouri-type charcoal kilns...

  3. RECYCLE AND REUSE OF CHARCOAL MADE FROM EXCESS SLUDGE IN MEMBRANE BIOREACTOR

    NASA Astrophysics Data System (ADS)

    Tran, Tuyet Thi; Shafiquzzaman, Md.; Nakajima, Jun

    Charcoal produced from excess sludge appeared to be useful for removing SMP (soluble microbial products) in MBR (membrane bioreactors) and therefore for reducing membrane fouling. Batch experiments and long-term MBR experiments were performed by using charcoal made of actual excess sludge. In the batch experiments, SMP was removed effectively through charcoal addition. This approach proved especially effective for the removal of carbohydrate. Charcoal would serve as an absorbent and coagulant in SMP removal. High BOD (biochemical oxygen demand) removal efficiencies produced no negative effects on biological activity in the reactors during the long-term MBR experiments involving charcoal addition. The decrease of humic substances and COD (chemical oxygen demand) through charcoal addition suggested that this approach effectively enhanced the performance of activated sludge treatment. A charcoal addition of more than 0.1% in long-term MBR experiments effectively decreased the membrane fouling frequency. The use of charcoal therefore served to mitigate membrane fouling. A decrease in carbohydrate, corresponding to the increase in the mean fouling period, suggested that a charcoal addition of more than 0.1% effectively removed SMP, especially carbohydrate. A charcoal cyclic reuse system is also proposed. This system would involve charcoal production and charcoal addition to MBR.

  4. EMISSIONS FROM STREET VENDOR COOKING DEVICES (CHARCOAL GRILLING)

    EPA Science Inventory

    The report discusses a joint U.S./Mexican program to establish a reliable emissions inventory for street vendor cooking devices (charcoal grilling), a significant source of air pollutants in the Mexicali-Imperial Valley area of Mexico. Emissions from these devices, prevalent in t...

  5. The role of activated charcoal in plant tissue culture.

    PubMed

    Thomas, T Dennis

    2008-01-01

    Activated charcoal has a very fine network of pores with large inner surface area on which many substances can be adsorbed. Activated charcoal is often used in tissue culture to improve cell growth and development. It plays a critical role in micropropagation, orchid seed germination, somatic embryogenesis, anther culture, synthetic seed production, protoplast culture, rooting, stem elongation, bulb formation etc. The promotary effects of AC on morphogenesis may be mainly due to its irreversible adsorption of inhibitory compounds in the culture medium and substancially decreasing the toxic metabolites, phenolic exudation and brown exudate accumulation. In addition to this activated charcoal is involved in a number of stimulatory and inhibitory activities including the release of substances naturally present in AC which promote growth, alteration and darkening of culture media, and adsorption of vitamins, metal ions and plant growth regulators, including abscisic acid and gaseous ethylene. The effect of AC on growth regulator uptake is still unclear but some workers believe that AC may gradually release certain adsorbed products, such as nutrients and growth regulators which become available to plants. This review focuses on the various roles of activated charcoal in plant tissue culture and the recent developments in this area.

  6. Activated charcoal. (Latest citations from the Compendex database). Published Search

    SciTech Connect

    Not Available

    1993-06-01

    The bibliography contains citations concerning theoretical aspects and industrial applications of activated charcoal. Topics include adsorption capacity and mechanism studies, kinetic and thermodynamic aspects, and description and evaluation of adsorptive abilities. Applications include use in water analyses and waste treatment, air pollution control and measurement, and in nuclear facilities. (Contains a minimum of 151 citations and includes a subject term index and title list.)

  7. Activated coconut shell charcoal carbon using chemical-physical activation

    NASA Astrophysics Data System (ADS)

    Budi, Esmar; Umiatin, Nasbey, Hadi; Bintoro, Ridho Akbar; Wulandari, Futri; Erlina

    2016-02-01

    The use of activated carbon from natural material such as coconut shell charcoal as metal absorbance of the wastewater is a new trend. The activation of coconut shell charcoal carbon by using chemical-physical activation has been investigated. Coconut shell was pyrolized in kiln at temperature about 75 - 150 °C for about 6 hours in producing charcoal. The charcoal as the sample was shieved into milimeter sized granule particle and chemically activated by immersing in various concentration of HCl, H3PO4, KOH and NaOH solutions. The samples then was physically activated using horizontal furnace at 400°C for 1 hours in argon gas environment with flow rate of 200 kg/m3. The surface morphology and carbon content of activated carbon were characterized by using SEM/EDS. The result shows that the pores of activated carbon are openned wider as the chemical activator concentration is increased due to an excessive chemical attack. However, the pores tend to be closed as further increasing in chemical activator concentration due to carbon collapsing.

  8. Small Scale Charcoal Making: A Manual for Trainers.

    ERIC Educational Resources Information Center

    Karch, Ed; And Others

    This training program offers skills training in all stages of the development of technologies related to small-scale charcoal production, including the design, construction, operation, maintenance, repair, and evaluation of prototype kilns. The kiln designs are selected to be as consistent as possible with the realities of rural areas in…

  9. Comparing modelled fire dynamics with charcoal records for the Holocene

    NASA Astrophysics Data System (ADS)

    Brücher, T.; Brovkin, V.; Kloster, S.; Marlon, J. R.; Power, M. J.

    2014-04-01

    An earth system model of intermediate complexity (CLIMate and BiosphERe - CLIMBER-2) and a land surface model (JSBACH), which dynamically represent vegetation, are used to simulate natural fire dynamics through the last 8000 yr. Output variables of the fire model (burned area and fire carbon emissions) are used to compare model results with sediment-based charcoal reconstructions. Several approaches for processing model output are also tested. Charcoal data are reported in Z-scores with a base period of 8000-200 BP in order to exclude the strong anthropogenic forcing of fire during the last two centuries. The model-data comparison reveals a robust correspondence in fire activity for most regions considered, while for a few regions, such as Europe, simulated and observed fire histories show different trends. The difference between modelled and observed fire activity may be due to the absence of anthropogenic forcing (e.g. human ignitions and suppression) in the model simulations, and also due to limitations inherent to modelling fire dynamics. The use of spatial averaging (or Z-score processing) of model output did not change the directions of the trends. However, Z-score-transformed model output resulted in higher rank correlations with the charcoal Z-scores in most regions. Therefore, while both metrics are useful, processing model output as Z-scores is preferable to areal averaging when comparing model results to transformed charcoal records.

  10. Comparing modelled fire dynamics with charcoal records for the Holocene

    NASA Astrophysics Data System (ADS)

    Brücher, T.; Brovkin, V.; Kloster, S.; Marlon, J. R.; Power, M. J.

    2013-11-01

    An Earth System model of intermediate complexity, CLIMBER-2, and a land surface model JSBACH that represents vegetation dynamically are used to simulate natural fire dynamics through the last 8000 yr. Output variables of the fire model (burned area and fire carbon emissions) are used to compare model results with sediment-based charcoal reconstructions and several approaches of model output processing are tested. Charcoal data are reported in Z-scores and have been used for the period 8000 to 200 BP to exclude the post-Industrial period of strong anthropogenic forcing during the last two centuries. The model-data comparison reveals a robust correspondence in fire trends for most regions considered, while few regions, such as Europe, display different trends between simulated and observed trends. The difference between the modelled and observed fire activity could be linked to an absence of the anthropogenic forcing (e.g., human ignitions and suppression) in the model simulations, but also related to limitations of model assumptions for modelling fire dynamics. For the model trends, the usage of spatial averaging or Z-score processing of model output resulted in similar directions of trend. However, modelled Z-scores resulted in higher rank correlations with the charcoal Z-scores in most of the regions. Therefore, while both metrics are useful, the Z-score processing is more preferable for the modelled fire comparison with the charcoal records than the areal averaging.

  11. Fire history reconstruction in grassland ecosystems: amount of charcoal reflects local area burned

    NASA Astrophysics Data System (ADS)

    Leys, Bérangère; Brewer, Simon C.; McConaghy, Scott; Mueller, Joshua; McLauchlan, Kendra K.

    2015-11-01

    Fire is one of the most prevalent disturbances in the Earth system, and its past characteristics can be reconstructed using charcoal particles preserved in depositional environments. Although researchers know that fires produce charcoal particles, interpretation of the quantity or composition of charcoal particles in terms of fire source remains poorly understood. In this study, we used a unique four-year dataset of charcoal deposited in traps from a native tallgrass prairie in mid-North America to test which environmental factors were linked to charcoal measurements on three spatial scales. We investigated small and large charcoal particles commonly used as a proxy of fire activity at different spatial scales, and charcoal morphotypes representing different types of fuel. We found that small (125-250 μm) and large (250 μm-1 mm) particles of charcoal are well-correlated (Spearman correlation = 0.88) and likely reflect the same spatial scale of fire activity in a system with both herbaceous and woody fuels. There was no significant relationship between charcoal pieces and fire parameters <500 m from the traps. Moreover, local area burned (<5 km distance radius from traps) explained the total charcoal amount, and regional burning (200 km radius distance from traps) explained the ratio of non arboreal to total charcoal (NA/T ratio). Charcoal variables, including total charcoal count and NA/T ratio, did not correlate with other fire parameters, vegetation cover, landscape, or climate variables. Thus, in long-term studies that involve fire history reconstructions, total charcoal particles, even of a small size (125-250 μm), could be an indicator of local area burned. Further studies may determine relationships among amount of charcoal recorded, fire intensity, vegetation cover, and climatic parameters.

  12. Determination of electrical resistivity of dry coke beds

    SciTech Connect

    Eidem, P.A.; Tangstad, M.; Bakken, J.A.

    2008-02-15

    The electrical resistivity of the coke bed is of great importance when producing FeMn, SiMn, and FeCr in a submerged arc furnace. In these processes, a coke bed is situated below and around the electrode tip and consists of metallurgical coke, slag, gas, and metal droplets. Since the basic mechanisms determining the electrical resistivity of a coke bed is not yet fully understood, this investigation is focused on the resistivity of dry coke beds consisting of different carbonaceous materials, i.e., coke beds containing no slag or metal. A method that reliably compares the electrical bulk resistivity of different metallurgical cokes at 1500{sup o} C to 1600{sup o}C is developed. The apparatus is dimensioned for industrial sized materials, and the electrical resistivity of anthracite, charcoal, petroleum coke, and metallurgical coke has been measured. The resistivity at high temperatures of the Magnitogorsk coke, which has the highest resistivity of the metallurgical cokes investigated, is twice the resistivity of the Corus coke, which has the lowest electrical resistivity. Zdzieszowice and SSAB coke sort in between with decreasing resistivities in the respective order. The electrical resistivity of anthracite, charcoal, and petroleum coke is generally higher than the resistivity of the metallurgical cokes, ranging from about two to about eight times the resistivity of the Corus coke at 1450{sup o}C. The general trend is that the bulk resistivity of carbon materials decreases with increasing temperature and increasing particle size.

  13. Builtin vs. auxiliary detection of extrapolation risk.

    SciTech Connect

    Munson, Miles Arthur; Kegelmeyer, W. Philip,

    2013-02-01

    A key assumption in supervised machine learning is that future data will be similar to historical data. This assumption is often false in real world applications, and as a result, prediction models often return predictions that are extrapolations. We compare four approaches to estimating extrapolation risk for machine learning predictions. Two builtin methods use information available from the classification model to decide if the model would be extrapolating for an input data point. The other two build auxiliary models to supplement the classification model and explicitly model extrapolation risk. Experiments with synthetic and real data sets show that the auxiliary models are more reliable risk detectors. To best safeguard against extrapolating predictions, however, we recommend combining builtin and auxiliary diagnostics.

  14. Microorganism communities and chemical characteristics in sludge-bamboo charcoal composting system.

    PubMed

    Hua, Li; Chen, Yingxu; Wu, Weixiang; Ma, Hongrui

    2011-04-01

    Microorganism communities and chemical characteristics in sludge-bamboo charcoal composting system were investigated to find the effect of bamboo charcoal on composting. According to a plate count test, abundances of bacteria, fungi and actinomycetes in the treatment with bamboo charcoal were several times higher than those in treatment without bamboo charcoal. In addition, terminal restriction fragment length polymorphism (TRFLP) analysis indicated that the bacterial community diversity in treatment with bamboo charcoal was greater than that of the control. Both results demonstrated that amendment with bamboo charcoal can increase microorganism population and microorganism community diversity in a sludge composting system. Moreover, the results of FTIR spectroscopy disclosed that aerobic composting can promote the formation of surface acid groups on bamboo charcoal. These surface acid groups may deprotonate and react with NH4+ to form stable complexes. Therefore, the increase of functional groups accompanied with greater assimilation of nitrogen by microorganisms could reduce nitrogen loss in sludge composting.

  15. Space Shuttle Orbiter improved auxiliary power unit

    NASA Technical Reports Server (NTRS)

    Hagemann, D. W.; Wicklund, L. L.; Loken, G. R.; Baughman, J. R.; Lance, R. J.

    1984-01-01

    The Space Shuttle Orbiter Auxiliary Power Unit subsystem has operated successfully on three vehicles by meeting mission requirements and has proven the design for space operation. The current Auxiliary Power Unit (APU) operational life is limited to 12 missions and the APU turnaround between flights is longer than originally anticipated. The Improved APU objective is to increase life to 50 missions, reduce the three - APU subsystem vehicle weight by 140 lbs., and reduce turnaround time. The design changes incorporated into the Improved APU and the associated development testing are described.

  16. Transport in Auxiliary Heated NSTX Discharges

    SciTech Connect

    B.P. LeBlanc; M.G. Bell; R.E. Bell; M.L. Bitte; C. Bourdelle; D.A. Gates; S.M. Kaye; R. Maingi; J.E. Menard; D. Mueller; M. Ono; S.F. Paul; M.H. Redi; A.L. Roquemore; A. Rosenberg; S.A. Sabbagh; D. Stutman; E.J. Synakowski; V.A. Soukhanovskii; J.R.Wilson

    2003-07-10

    The NSTX spherical torus (ST) provides a unique platform to investigate magnetic confinement in auxiliary-heated plasmas at low aspect ratio. Auxiliary power is routinely coupled to ohmically heated plasmas by deuterium neutral-beam injection (NBI) and by high-harmonic fast waves (HHFW) launch. While theory predicts both techniques to preferentially heat electrons, experiment reveals the electron temperature is greater than the ion temperature during HHFW, but the electron temperature is less than the ion temperature during NBI. In the following we present the experimental data and the results of transport analyses.

  17. Design tradeoffs of a reciprocating auxiliary power unit

    NASA Astrophysics Data System (ADS)

    Renquist, Jacob Vinod

    This thesis presents a comparison of reciprocating auxiliary power units to conventional, gas turbine auxiliary power units. A metric of interest is created to represent the specific auxiliary power system weight including the prime mover, generator, gearbox, and fuel consumed. The metric of interest is used to compare the different auxiliary power unit technologies by incorporating detailed engine simulations, auxiliary power unit system weight modeling, and flight path-realized fuel consumption modeling. Results show that reciprocating auxiliary power units can be competitive with gas turbines in near-term, more-electric aircraft applications.

  18. Modelling the combustion of charcoal in a model blast furnace

    NASA Astrophysics Data System (ADS)

    Shen, Yansong; Shiozawa, Tomo; Yu, Aibing; Austin, Peter

    2013-07-01

    The pulverized charcoal (PCH) combustion in ironmaking blast furnaces is abstracting remarkable attention due to various benefits such as lowering CO2 emission. In this study, a three-dimensional CFD model is used to simulate the flow and thermo-chemical behaviours in this process. The model is validated against the experimental results from a pilot-scale combustion test rig for a range of conditions. The typical flow and thermo-chemical phenomena is simulated. The effect of charcoal type, i.e. VM content is examined, showing that the burnout increases with VM content in a linear relationship. This model provides an effective way for designing and optimizing PCH operation in blast furnace practice.

  19. Charcoal analysis and Holocene vegetation history in southern Syria

    NASA Astrophysics Data System (ADS)

    Willcox, George

    1999-04-01

    Charcoal analysis of three archaeological sites in southern Syria in the vicinity of the Jebel al Arab (formerly Jebel Druze) indicates that during the Early Bronze Age an association consisting predominately of Pistacia, deciduous oak and almond was exploited. During the Middle Bronze Age these taxa diminish and are partially replaced by more steppic species or introduced wood such as olive. During the Roman period evergreen oak appeared in the region and gradually replaced the deciduous oak which is now restricted to a small area. The gradual replacement of deciduous oaks by evergreen oaks has been observed in other areas of the Mediterranean basin during the Holocene. Conifer charcoal such as pine and cedar is present on the sites, but it is not clear whether these were local or imported from farther away, for example, the Lebanese highlands. During the Middle Bronze Age olive wood was also used as combustible but here also its exact origin is not known.

  20. Auxiliary power unit for moving a vehicle

    DOEpatents

    Akasam, Sivaprasad; Johnson, Kris W.; Johnson, Matthew D.; Slone, Larry M.; Welter, James Milton

    2009-02-03

    A power system is provided having at least one traction device and a primary power source configured to power the at least one traction device. In addition, the power system includes an auxiliary power source also configured to power the at least one traction device.

  1. Auxiliary Personnel in the Elementary School.

    ERIC Educational Resources Information Center

    The National Elementary Principal, 1967

    1967-01-01

    The first article in this collection of 12 is reprinted from "Auxiliary School Personnel," a booklet published by the National Commission on Teacher Education and Professional Standards. A series on "S.721: Teacher Aide Program Support Act of 1967" includes a copy of the bill, remarks made by U.S. Senator Gaylord Nelson when he introduced it, and…

  2. 14 CFR 23.757 - Auxiliary floats.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Auxiliary floats. 23.757 Section 23.757 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS... fresh water, they provide a righting moment of at least 1.5 times the upsetting moment caused by...

  3. 78 FR 27321 - Revision of Auxiliary Regulations

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-10

    ... public dockets in the January 17, 2008 issue of the Federal Register (73 FR 3316). D. Public Meeting We... last updated in 2003 (68 FR 9534, Feb 28, 2003) and 1996 (61 FR 33662, June 28, 1996), but these... other administrative matters. These changes would address several problems common to Auxiliary...

  4. Ejector Noise Suppression with Auxiliary Jet Injection

    NASA Technical Reports Server (NTRS)

    Berman, Charles H.; Andersen, Otto P., Jr.

    1997-01-01

    An experimental program to reduce aircraft jet turbulence noise investigated the interaction of small auxiliary jets with a larger main jet. Significant reductions in the far field jet noise were obtained over a range of auxiliary jet pressures and flow rates when used in conjunction with an acoustically lined ejector. While the concept is similar to that of conventional ejector suppressors that use mechanical mixing devices, the present approach should improve thrust and lead to lower weight and less complex noise suppression systems since no hardware needs to be located in the main jet flow. A variety of auxiliary jet and ejector configurations and operating conditions were studied. The best conditions tested produced peak to peak noise reductions ranging from 11 to 16 dB, depending on measurement angle, for auxiliary jet mass flows that were 6.6% of the main jet flow with ejectors that were 8 times the main jet diameter in length. Much larger reductions in noise were found at the original peak frequencies of the unsuppressed jet over a range of far field measurement angles.

  5. 47 CFR 73.1675 - Auxiliary antennas.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... main antenna or at a separate site. The service contour of the auxiliary antenna may not extend beyond the following corresponding contour for the main facility: (i) AM stations: The 0.5 mV/m field strength contours. (ii) FM stations: The 1.0 mV/m field strength contours. (iii) TV stations: The Grade...

  6. 47 CFR 73.1675 - Auxiliary antennas.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... main antenna or at a separate site. The service contour of the auxiliary antenna may not extend beyond the following corresponding contour for the main facility: (i) AM stations: The 0.5 mV/m field strength contours. (ii) FM stations: The 1.0 mV/m field strength contours. (iii) TV stations: The Grade...

  7. 47 CFR 73.1675 - Auxiliary antennas.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... main antenna or at a separate site. The service contour of the auxiliary antenna may not extend beyond the following corresponding contour for the main facility: (i) AM stations: The 0.5 mV/m field strength contours. (ii) FM stations: The 1.0 mV/m field strength contours. (iii) TV stations: The Grade...

  8. 47 CFR 73.1675 - Auxiliary antennas.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... main antenna or at a separate site. The service contour of the auxiliary antenna may not extend beyond the following corresponding contour for the main facility: (i) AM stations: The 0.5 mV/m field strength contours. (ii) FM stations: The 1.0 mV/m field strength contours. (iii) TV stations: The Grade...

  9. 47 CFR 73.1675 - Auxiliary antennas.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... main antenna or at a separate site. The service contour of the auxiliary antenna may not extend beyond the following corresponding contour for the main facility: (i) AM stations: The 0.5 mV/m field strength contours. (ii) FM stations: The 1.0 mV/m field strength contours. (iii) TV stations: The Grade...

  10. 47 CFR 97.201 - Auxiliary station.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES AMATEUR RADIO SERVICE Special Operations § 97.201 Auxiliary station. (a) Any amateur station licensed to a holder of a Technician, Technician Plus, General, Advanced or Amateur Extra Class operator license may be an...

  11. The Changing Face of Auxiliary Services

    ERIC Educational Resources Information Center

    Villano, Matt

    2006-01-01

    With tuition on the rise, Auxiliary Services departments at a variety of colleges and universities are proving that they can innovate and still save their parent institutions cash. Primary areas of innovation include: (1) With advancements in technology, institutions are moving campus purchasing programs into the wireless space; (2) As junk mail …

  12. Curricular Guidelines for Dental Auxiliary Radiology.

    ERIC Educational Resources Information Center

    Journal of Dental Education, 1981

    1981-01-01

    AADS curricular guidelines suggest objectives for these areas of dental auxiliary radiology: physical principles of X-radiation in dentistry, related radiobiological concepts, principles of radiologic health, radiographic technique, x-ray films and intensifying screens, factors contributing to film quality, darkroom, and normal variations in…

  13. Bed Bugs FAQs

    MedlinePlus

    ... Tropical Diseases Laboratory Diagnostic Assistance [DPDx] Parasites Home Bed Bugs FAQs Recommend on Facebook Tweet Share Compartir On ... are bed bugs treated and prevented? What are bed bugs? Bed bugs ( Cimex lectularius ) are small, flat, parasitic ...

  14. Comparing modelled fire dynamics with charcoal records for the Holocene

    NASA Astrophysics Data System (ADS)

    Brücher, Tim; Brovkin, Victor; Kloster, Silvia; Marlon, Jennifer; Power, Mitch

    2014-05-01

    An Earth System model of intermediate complexity, CLIMBER-2, and land surface model JSBACH that includes dynamic vegetation, carbon cycle, and fire regime are used for simulation of natural fire dynamics through the last 8,000 years. To compare the fire model results with the charcoal reconstructions, several output variables of the fire model (burned area, carbon emissions) and several approaches of model output processing are tested. The z-scores out of charcoal dataset have been calculated for the period 8,000 to 200 BP to exclude a period of strong anthropogenic forcing during the last two centuries. The model analysis points mainly to an increasing fire activity during the Holocene for most of the investigated areas, which is in good correspondence to reconstructed fire trends out of charcoal data for most of the tested regions, while for few regions such as Europe the simulated trend and the reconstructed trends are different. The difference between the modeled and reconstructed fire activity could be due to absence of the anthropogenic forcing in the model simulations, but also due to limitations of model assumptions for modeling fire dynamics. For the model trends, the usage of averaging or z-score processing of model output resulted in similar directions of trend. Therefore, the approach of fire model output processing does not effect results of the model-data comparison. Global fire modeling is still in its infancy; improving our representations of fire through validation exercises such as what we present here is thus essential before testing hypotheses about the effects of extreme climate changes on fire behavior and potential feedbacks that result from those changes. Brücher, T., Brovkin, V., Kloster, S., Marlon, J. R., and Power, M. J.: Comparing modelled fire dynamics with charcoal records for the Holocene, Clim. Past Discuss., 9, 6429-6458, doi:10.5194/cpd-9-6429-2013, 2013.

  15. A facile synthesis of Fe3O4-charcoal composite for the sorption of a hazardous dye from aquatic environment.

    PubMed

    Ahmed, Md Juned K; Ahmaruzzaman, M

    2015-11-01

    Herein, we synthesized Fe3O4-charcoal composite using chemical precipitation technique and utilized it for the sorption of methylene blue from aqueous solution. The synthesized composite was characterized by Infra-red spectroscopy, N2 adsorption-desorption isotherm, X-ray diffraction, selected area electron diffraction, transmission electron microscopy, and vibrating sample magnetometer. The composite depicts absorption bands conforming to Fe-O, -OH, CO, and C-O vibrations. The composite was mesoporous in nature with a surface area of 387.30 m(2) g(-1). The observed diffraction planes correspond to face-centered cubic Fe3O4 and disordered graphitic carbon. The spherical Fe3O4 particles (average diameter ∼13.8 nm) were uniformly distributed in the carbon matrix of the charcoal. The saturation and remanent magnetizations demonstrate its potential for magnetic separation and reuse. The composite showed dye sorption capacities of 97.49 mg g(-1) and 90.85 mg g(-1) in batch and fixed-bed system. Pseudo-second order kinetics and Temkin isotherm best represented the sorption data. The sorption process was endothermic, spontaneous, and administered by electrostatic, π-π dispersive interactions, film, and intraparticle diffusion. Microwave irradiations followed by methanol elution regenerated the dye-loaded composite with nearly no loss in sorption capacity. The recovery of energy and potential utilization of bottom ash enhances the prospective of Fe3O4-charcoal composite for industrial applications.

  16. A facile synthesis of Fe3O4-charcoal composite for the sorption of a hazardous dye from aquatic environment.

    PubMed

    Ahmed, Md Juned K; Ahmaruzzaman, M

    2015-11-01

    Herein, we synthesized Fe3O4-charcoal composite using chemical precipitation technique and utilized it for the sorption of methylene blue from aqueous solution. The synthesized composite was characterized by Infra-red spectroscopy, N2 adsorption-desorption isotherm, X-ray diffraction, selected area electron diffraction, transmission electron microscopy, and vibrating sample magnetometer. The composite depicts absorption bands conforming to Fe-O, -OH, CO, and C-O vibrations. The composite was mesoporous in nature with a surface area of 387.30 m(2) g(-1). The observed diffraction planes correspond to face-centered cubic Fe3O4 and disordered graphitic carbon. The spherical Fe3O4 particles (average diameter ∼13.8 nm) were uniformly distributed in the carbon matrix of the charcoal. The saturation and remanent magnetizations demonstrate its potential for magnetic separation and reuse. The composite showed dye sorption capacities of 97.49 mg g(-1) and 90.85 mg g(-1) in batch and fixed-bed system. Pseudo-second order kinetics and Temkin isotherm best represented the sorption data. The sorption process was endothermic, spontaneous, and administered by electrostatic, π-π dispersive interactions, film, and intraparticle diffusion. Microwave irradiations followed by methanol elution regenerated the dye-loaded composite with nearly no loss in sorption capacity. The recovery of energy and potential utilization of bottom ash enhances the prospective of Fe3O4-charcoal composite for industrial applications. PMID:26320009

  17. [Effects of bamboo charcoal on the growth of Trifolium repens and soil bacterial community structure].

    PubMed

    Li, Song-Hao; He, Dong-Hua; Shen, Qiu-Lan; Xu, Qiu-Fang

    2014-08-01

    The effects of addition rates (0, 3% and 9%) and particle sizes (0.05, 0.05-1.0 and 1.0-2.0 mm) of bamboo charcoal on the growth of Trifolium repens and soil microbial community structure were investigated. The results showed that bamboo charcoal addition greatly promoted the early growth of T. repens, with the 9% charcoal addition rate being slightly better than the 3% charcoal addition rate. The effects of different particle sizes of bamboo charcoal on the growth of T. repens were not different significantly. Growth promotion declined with time during 120 days after sowing, and disappeared completely after 5 months. DGGE analysis of the bacterial 16S rDNA V3 fragment indicated that bamboo charcoal altered the soil bacterial community structure. The amount and Shannon diversity index of bacteria in the bamboo charcoal addition treatments increased compared with CK. The quantitative analysis showed that the amount of bacteria in the treatment with bamboo charcoal of fine particle (D < 0.05 mm) at the 9% addition rate was significantly higher than in the other treatments. The fine bamboo charcoal had a great effect on soil bacteria amount compared with the charcoal of other sizes at the same addition rate.

  18. The impact of media reporting on the emergence of charcoal burning suicide in Taiwan.

    PubMed

    Chen, Ying-Yeh; Chen, Feng; Gunnell, David; Yip, Paul S F

    2013-01-01

    We investigated the association of the intensity of newspaper reporting of charcoal burning suicide with the incidence of such deaths in Taiwan during 1998-2002. A counting process approach was used to estimate the incidence of suicides and intensity of news reporting. Conditional Poisson generalized linear autoregressive models were performed to assess the association of the intensity of newspaper reporting of charcoal burning and non-charcoal burning suicides with the actual number of charcoal burning and non-charcoal burning suicides the following day. We found that increases in the reporting of charcoal burning suicide were associated with increases in the incidence of charcoal burning suicide on the following day, with each reported charcoal burning news item being associated with a 16% increase in next day charcoal burning suicide (p<.0001). However, the reporting of other methods of suicide was not related to their incidence. We conclude that extensive media reporting of charcoal burning suicides appears to have contributed to the rapid rise in the incidence of the novel method in Taiwan during the initial stage of the suicide epidemic. Regulating media reporting of novel suicide methods may prevent an epidemic spread of such new methods.

  19. The Impact of Media Reporting on the Emergence of Charcoal Burning Suicide in Taiwan

    PubMed Central

    Chen, Ying-Yeh; Chen, Feng; Gunnell, David; Yip, Paul S. F.

    2013-01-01

    We investigated the association of the intensity of newspaper reporting of charcoal burning suicide with the incidence of such deaths in Taiwan during 1998–2002. A counting process approach was used to estimate the incidence of suicides and intensity of news reporting. Conditional Poisson generalized linear autoregressive models were performed to assess the association of the intensity of newspaper reporting of charcoal burning and non-charcoal burning suicides with the actual number of charcoal burning and non-charcoal burning suicides the following day. We found that increases in the reporting of charcoal burning suicide were associated with increases in the incidence of charcoal burning suicide on the following day, with each reported charcoal burning news item being associated with a 16% increase in next day charcoal burning suicide (p<.0001). However, the reporting of other methods of suicide was not related to their incidence. We conclude that extensive media reporting of charcoal burning suicides appears to have contributed to the rapid rise in the incidence of the novel method in Taiwan during the initial stage of the suicide epidemic. Regulating media reporting of novel suicide methods may prevent an epidemic spread of such new methods. PMID:23383027

  20. Variability in oxidative degradation of charcoal: Influence of production conditions and environmental exposure

    NASA Astrophysics Data System (ADS)

    Ascough, P. L.; Bird, M. I.; Francis, S. M.; Thornton, B.; Midwood, A. J.; Scott, A. C.; Apperley, D.

    2011-05-01

    Charcoal is a key component of the Black Carbon (BC) continuum, where BC is characterized as a recalcitrant, fire-derived, polyaromatic material. Charcoal is an important source of palaeoenvironmental data, and of great interest as a potential carbon sink, due to its high apparent environmental stability. However, at least some forms of charcoal are clearly susceptible to environmental alteration and degradation over relatively short timescales. Although these processes have importance for the role of charcoal in global biogeochemistry, they remain poorly understood. Here we present results of an investigation into the susceptibility of a range of charcoal samples to oxidative degradation in acidified potassium dichromate. The study examines both freshly-produced charcoal, and charcoal exposed to environmental conditions for up to 50,000 years. We compare the proportion of carbon present in different forms between the samples, specifically with respect to the relative chemical resistance of these forms. This was undertaken in order to improve understanding of the post-depositional diagenetic changes affecting charcoal within environmental deposits. A wide range in chemical compositions are apparent both within and between the sample groups. In freshly-produced charcoal, material produced at 300 °C contains carbon with more labile forms than charcoal produced at ⩾400 °C, signifying a key chemical change over the 300-400 °C temperature range. Charcoal exposed to environmental depositional conditions is frequently composed of a highly carboxylated aromatic structure and contains a range of carbon fractions of varying oxidative resistance. These findings suggest that a significant number of the environmental charcoals have undergone post-depositional diagenetic alteration. Further, the data highlight the potential for the use of controlled progressive oxidative degradation as a method to characterize chemical differences between individual charcoal samples.

  1. 42. AUXILIARY CHAMBER, VIEW LOOKING EAST FROM WEST END, OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    42. AUXILIARY CHAMBER, VIEW LOOKING EAST FROM WEST END, OF AUXILIARY PIPING, STEAM, FEEDWATER PIPING (LOCATION BBB) - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  2. 33 CFR 5.48 - Auxiliary Patrol Boat ensign.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... ensign is authorized to be flown on all Auxiliary Operational Facility vessels under orders. The penalty for the unauthorized flying of any ensign, flag or pennant of the Auxiliary is set forth in § 5.67...

  3. 33 CFR 5.48 - Auxiliary Patrol Boat ensign.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... ensign is authorized to be flown on all Auxiliary Operational Facility vessels under orders. The penalty for the unauthorized flying of any ensign, flag or pennant of the Auxiliary is set forth in § 5.67...

  4. 49 CFR 193.2613 - Auxiliary power sources.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY LIQUEFIED NATURAL GAS FACILITIES: FEDERAL SAFETY STANDARDS Maintenance § 193.2613 Auxiliary power sources. Each auxiliary power source...

  5. 33 CFR 5.48 - Auxiliary Patrol Boat ensign.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... ensign is authorized to be flown on all Auxiliary Operational Facility vessels under orders. The penalty for the unauthorized flying of any ensign, flag or pennant of the Auxiliary is set forth in § 5.67...

  6. CTR Fuel recovery system using regeneration of a molecular sieve drying bed

    DOEpatents

    Folkers, Charles L.

    1981-01-01

    A primary molecular sieve drying bed is regenerated by circulating a hot inert gas through the heated primary bed to desorb water held on the bed. The inert gas plus water vapor is then cooled and passed through an auxiliary molecular sieve bed which adsorbs the water originally desorbed from the primary bed. The main advantage of the regeneration technique is that the partial pressure of water can be reduced to the 10.sup.-9 atm. range. This is significant in certain CTR applications where tritiated water (T.sub.2 O, HTO) must be collected and kept at very low partial pressure.

  7. 28 CFR 36.303 - Auxiliary aids and services.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 28 Judicial Administration 1 2013-07-01 2013-07-01 false Auxiliary aids and services. 36.303... BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Specific Requirements § 36.303 Auxiliary aids... differently than other individuals because of the absence of auxiliary aids and services, unless the...

  8. 28 CFR 36.303 - Auxiliary aids and services.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 28 Judicial Administration 1 2014-07-01 2014-07-01 false Auxiliary aids and services. 36.303... BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Specific Requirements § 36.303 Auxiliary aids... differently than other individuals because of the absence of auxiliary aids and services, unless the...

  9. 28 CFR 36.303 - Auxiliary aids and services.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Auxiliary aids and services. 36.303... BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Specific Requirements § 36.303 Auxiliary aids... differently than other individuals because of the absence of auxiliary aids and services, unless the...

  10. 28 CFR 36.303 - Auxiliary aids and services.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 28 Judicial Administration 1 2011-07-01 2011-07-01 false Auxiliary aids and services. 36.303... BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Specific Requirements § 36.303 Auxiliary aids... differently than other individuals because of the absence of auxiliary aids and services, unless the...

  11. 28 CFR 36.303 - Auxiliary aids and services.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 28 Judicial Administration 1 2012-07-01 2012-07-01 false Auxiliary aids and services. 36.303... BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Specific Requirements § 36.303 Auxiliary aids... differently than other individuals because of the absence of auxiliary aids and services, unless the...

  12. 14 CFR 25.445 - Auxiliary aerodynamic surfaces.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Auxiliary aerodynamic surfaces. 25.445... § 25.445 Auxiliary aerodynamic surfaces. (a) When significant, the aerodynamic influence between auxiliary aerodynamic surfaces, such as outboard fins and winglets, and their supporting...

  13. 14 CFR 25.445 - Auxiliary aerodynamic surfaces.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Auxiliary aerodynamic surfaces. 25.445... § 25.445 Auxiliary aerodynamic surfaces. (a) When significant, the aerodynamic influence between auxiliary aerodynamic surfaces, such as outboard fins and winglets, and their supporting...

  14. 14 CFR 25.445 - Auxiliary aerodynamic surfaces.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Auxiliary aerodynamic surfaces. 25.445... § 25.445 Auxiliary aerodynamic surfaces. (a) When significant, the aerodynamic influence between auxiliary aerodynamic surfaces, such as outboard fins and winglets, and their supporting...

  15. 14 CFR 25.445 - Auxiliary aerodynamic surfaces.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Auxiliary aerodynamic surfaces. 25.445... § 25.445 Auxiliary aerodynamic surfaces. (a) When significant, the aerodynamic influence between auxiliary aerodynamic surfaces, such as outboard fins and winglets, and their supporting...

  16. 30 CFR 57.8529 - Auxiliary fan systems

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Auxiliary fan systems 57.8529 Section 57.8529 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Underground Only § 57.8529 Auxiliary fan systems When auxiliary fan systems are used, such systems...

  17. 30 CFR 57.8529 - Auxiliary fan systems

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Auxiliary fan systems 57.8529 Section 57.8529 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Underground Only § 57.8529 Auxiliary fan systems When auxiliary fan systems are used, such systems...

  18. 30 CFR 57.8529 - Auxiliary fan systems.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Auxiliary fan systems. 57.8529 Section 57.8529 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Underground Only § 57.8529 Auxiliary fan systems. When auxiliary fan systems are used, such systems...

  19. 30 CFR 57.8529 - Auxiliary fan systems

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Auxiliary fan systems 57.8529 Section 57.8529 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Underground Only § 57.8529 Auxiliary fan systems When auxiliary fan systems are used, such systems...

  20. 30 CFR 57.8529 - Auxiliary fan systems.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Auxiliary fan systems. 57.8529 Section 57.8529 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Underground Only § 57.8529 Auxiliary fan systems. When auxiliary fan systems are used, such systems...

  1. 49 CFR 193.2613 - Auxiliary power sources.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Auxiliary power sources. 193.2613 Section 193.2613...: FEDERAL SAFETY STANDARDS Maintenance § 193.2613 Auxiliary power sources. Each auxiliary power source must... test must take into account the power needed to start up and simultaneously operate equipment...

  2. 46 CFR 182.620 - Auxiliary means of steering.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 7 2012-10-01 2012-10-01 false Auxiliary means of steering. 182.620 Section 182.620... TONS) MACHINERY INSTALLATION Steering Systems § 182.620 Auxiliary means of steering. (a) Except as provided in paragraph (c) of this section, a vessel must be provided with an auxiliary means of...

  3. 46 CFR 182.620 - Auxiliary means of steering.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 7 2011-10-01 2011-10-01 false Auxiliary means of steering. 182.620 Section 182.620... TONS) MACHINERY INSTALLATION Steering Systems § 182.620 Auxiliary means of steering. (a) Except as provided in paragraph (c) of this section, a vessel must be provided with an auxiliary means of...

  4. 14 CFR 29.551 - Auxiliary lifting surfaces.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Auxiliary lifting surfaces. 29.551 Section 29.551 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT....551 Auxiliary lifting surfaces. Each auxiliary lifting surface must be designed to withstand— (a)...

  5. Removal of NOx or its conversion into harmless gases by charcoals and composites of metal oxides

    SciTech Connect

    Ishihara, Shigehisa; Furutsuka, Takeshi

    1996-12-31

    In recent years, much attention has been devoted to environmental problems such as acid rain, photochemical smog and water pollution. In particular, NOx emissions from factories, auto mobiles, etc. in urban areas have become worse. To solve these problems on environmental pollution on a global scale, the use of activated charcoal to reduce air pollutants is increasing. However, the capability of wood-based charcoal materials is not yet fully known. The removal of NOx or its conversion into harmless gases such as N{sub 2} should be described. In this study, the adsorption of NO over wood charcoal or metal oxide-dispersed wood charcoal was investigated. In particular, carbonized wood powder of Sugi (Cryptomeria japonica D. Don) was used to study the effectivity of using these materials in adsorbing NOx. Since wood charcoal is chemically stable, metal oxide with the ability of photocatalysis was dispersed into wood charcoal to improve its adsorption and capability to use the light energy effectively.

  6. Global charcoal mobilization from soils via dissolution and riverine transport to the oceans.

    PubMed

    Jaffé, Rudolf; Ding, Yan; Niggemann, Jutta; Vähätalo, Anssi V; Stubbins, Aron; Spencer, Robert G M; Campbell, John; Dittmar, Thorsten

    2013-04-19

    Global biomass burning generates 40 million to 250 million tons of charcoal every year, part of which is preserved for millennia in soils and sediments. We have quantified dissolution products of charcoal in a wide range of rivers worldwide and show that globally, a major portion of the annual charcoal production is lost from soils via dissolution and subsequent transport to the ocean. The global flux of soluble charcoal accounts to 26.5 ± 1.8 million tons per year, which is ~10% of the global riverine flux of dissolved organic carbon (DOC). We suggest that the mobilization of charcoal and DOC out of soils is mechanistically coupled. This study closes a major gap in the global charcoal budget and provides critical information in the context of geoengineering.

  7. Comment on "Fire-derived charcoal causes loss of forest humus".

    PubMed

    Lehmann, Johannes; Sohi, Saran

    2008-09-01

    Wardle et al. (Brevia, 2 May 2008, p. 629) reported that fire-derived charcoal can promote loss of forest humus and belowground carbon (C). However, C loss from charcoal-humus mixtures can be explained not only by accelerated loss of humus but also by loss of charcoal. It is also unclear whether such loss is related to mineralization to carbon dioxide or to physical export.

  8. Recovery and Determination of Adsorbed Technetium on Savannah River Site Charcoal Stack Samples

    SciTech Connect

    Lahoda, Kristy G.; Engelmann, Mark D.; Farmer, Orville T.; Ballou, Nathan E.

    2008-03-01

    Experimental results are provided for the sample analyses for technetium (Tc) in charcoal samples placed in-line with a Savannah River Site (SRS) processing stack effluent stream as a part of an environmental surveillance program. The method for Tc removal from charcoal was based on that originally developed with high purity charcoal. Presented is the process that allowed for the quantitative analysis of 99Tc in SRS charcoal stack samples with and without 97Tc as a tracer. The results obtained with the method using the 97Tc tracer quantitatively confirm the results obtained with no tracer added. All samples contain 99Tc at the pg g-1 level.

  9. Comparison of Impurities in Charcoal Sorbents Found by Neutron Activation Analysis

    SciTech Connect

    Doll, Charles G.; Finn, Erin C.; Cantaloub, Michael G.; Greenwood, Lawrence R.; Kephart, Jeremy; Kephart, Rosara F.

    2013-01-01

    Abstract: Neutron activation of gas samples in a reactor often requires a medium to retain sufficient amounts of the gas for analysis. Charcoal is commonly used to adsorb gas and hold it for activation; however, the amount of activated sodium in the charcoal after irradiation swamps most signals of interest. Neutron activation analysis (NAA) was performed on several commonly available charcoal samples in an effort to determine the activation background. The results for several elements, including the dominant sodium element, are reported. It was found that ECN charcoal had the lowest elemental background, containing sodium at 2.65 ± 0.05 ppm, as well as trace levels of copper and tungsten.

  10. Charcoal morphometry for paleoecological analysis: The effects of fuel type and transportation on morphological parameters1

    PubMed Central

    Crawford, Alastair J.; Belcher, Claire M.

    2014-01-01

    • Premise of the study: Charcoal particles preserved in sediments are used as indicators of paleowildfire. Most research focuses on abundance as an indicator of fire frequency, but charcoals also convey information about the vegetation from which they are derived. One potential source of information is their morphology, which is influenced by the parent material, the nature of the fire, and subsequent transportation and burial. • Methods: We charcoalified 26 materials from a range of plant taxa, and subjected them to simulated fluvial transport by tumbling them with water and gravel. We photographed the resulting particles, and used image analysis software to measure morphological parameters. • Results: Leaf charcoal displayed a logarithmic decrease in area, and a logarithmic increase in circularity, with transportation time. Trends were less clear for stem or wood charcoal. Grass charcoal displayed significantly higher aspect ratios than other charcoal types. • Conclusions: Leaf charcoal displays more easily definable relationships between morphological parameters and degree of breakdown than stem or wood charcoal. The aspect ratios of fossil mesocharcoal can indicate the broad botanical source of an assemblage. Coupled to estimates of charcoal abundance, this will improve understanding of the variation in flammability of ancient ecosystems. PMID:25202644

  11. The effect of weathering on charcoal filter performance. 2; The effect of contaminants on the CH sub 3 I removal efficiency of TEDA charcoal

    SciTech Connect

    Wren, J.C.; Moore, C.J. )

    1991-05-01

    The effect of various contaminants, namely NO{sub 2} SO{sub 2}, 2-butanone (methyl-ethyl-ketone (MEK)), and NH{sub 3}, on the radioiodine removal efficiency of triethylenediamine (TEDA)-impregnated charcoal filters has been studied, and an attempt was made to characterize and quantify the weathering process of TEDA charcoal by these contaminants. The effects of the contaminants on the CH{sub 3}I removal efficiency of TEDA charcoal under dry and humid conditions are described. Based on our results, the efficiency of TEDA charcoal is degraded most by NO{sub 2} and SO{sub 2}, NH{sub 3} has a negligible effect, and MEK produces a mild degradation. The degree of degradation parallels the contaminant's ability to be chemisorbed on the TEDA impregnant. The combined effect of water vapor and a contaminant of the charcoal efficiency is different for each contaminant. Nitrogen dioxide absorbed under dry conditions is more effective in degrading the CH{sub 2}I removal efficiency of the charcoal that when absorbed under humid conditions. On the other hand, a completely opposite result is observed for SO{sub 2}. The MEK contaminant behaves similarly to SO{sub 2} but the effect of humidity was less significant than for SO{sub 2}. Ammonia has no effect on the efficiency of the charcoal regardless of humidity.

  12. Acute Kidney Injury Predicts Mortality after Charcoal Burning Suicide

    PubMed Central

    Chen, Yu-Chin; Tseng, Yi-Chia; Huang, Wen-Hung; Hsu, Ching-Wei; Weng, Cheng-Hao; Liu, Shou-Hsuan; Yang, Huang-Yu; Chen, Kuan-Hsin; Chen, Hui-Ling; Fu, Jen-Fen; Lin, Wey-Ran; Wang, I-Kuan; Yen, Tzung-Hai

    2016-01-01

    A paucity of literature exists on risk factors for mortality in charcoal burning suicide. In this observational study, we analyzed the data of 126 patients with charcoal burning suicide that seen between 2002 and 2013. Patients were grouped according to status of renal damage as acute kidney injury (N = 49) or non-acute kidney injury (N = 77). It was found that patients with acute kidney injury suffered severer complications such as respiratory failure (P = 0.002), myocardial injury (P = 0.049), hepatic injury (P < 0.001), rhabdomyolysis (P = 0.045) and out-of-hospital cardiac arrest (P = 0.028) than patients without acute kidney injury. Moreover, patients with acute kidney injury suffered longer hospitalization duration (16.9 ± 18.3 versus 10.7 ± 10.9, P = 0.002) and had higher mortality rate (8.2% versus 0%, P = 0.011) than patients without injury. In a multivariate Cox regression model, it was demonstrated that serum creatinine level (P = 0.019) and heart rate (P = 0.022) were significant risk factors for mortality. Finally, Kaplan-Meier analysis revealed that patients with acute kidney injury suffered lower cumulative survival than without injury (P = 0.016). In summary, the overall mortality rate of charcoal burning suicide population was 3.2%, and acute kidney injury was a powerful predictor of mortality. Further studies are warranted. PMID:27430168

  13. Acute Kidney Injury Predicts Mortality after Charcoal Burning Suicide.

    PubMed

    Chen, Yu-Chin; Tseng, Yi-Chia; Huang, Wen-Hung; Hsu, Ching-Wei; Weng, Cheng-Hao; Liu, Shou-Hsuan; Yang, Huang-Yu; Chen, Kuan-Hsin; Chen, Hui-Ling; Fu, Jen-Fen; Lin, Wey-Ran; Wang, I-Kuan; Yen, Tzung-Hai

    2016-01-01

    A paucity of literature exists on risk factors for mortality in charcoal burning suicide. In this observational study, we analyzed the data of 126 patients with charcoal burning suicide that seen between 2002 and 2013. Patients were grouped according to status of renal damage as acute kidney injury (N = 49) or non-acute kidney injury (N = 77). It was found that patients with acute kidney injury suffered severer complications such as respiratory failure (P = 0.002), myocardial injury (P = 0.049), hepatic injury (P < 0.001), rhabdomyolysis (P = 0.045) and out-of-hospital cardiac arrest (P = 0.028) than patients without acute kidney injury. Moreover, patients with acute kidney injury suffered longer hospitalization duration (16.9 ± 18.3 versus 10.7 ± 10.9, P = 0.002) and had higher mortality rate (8.2% versus 0%, P = 0.011) than patients without injury. In a multivariate Cox regression model, it was demonstrated that serum creatinine level (P = 0.019) and heart rate (P = 0.022) were significant risk factors for mortality. Finally, Kaplan-Meier analysis revealed that patients with acute kidney injury suffered lower cumulative survival than without injury (P = 0.016). In summary, the overall mortality rate of charcoal burning suicide population was 3.2%, and acute kidney injury was a powerful predictor of mortality. Further studies are warranted. PMID:27430168

  14. Comparing modeled fire dynamics with charcoal records for the Holocene

    NASA Astrophysics Data System (ADS)

    Bruecher, T.; Brovkin, V.; Kloster, S.; Marlon, J. R.; Power, M. J.

    2013-12-01

    An Earth System model of intermediate complexity, CLIMBER-2, and land surface model JSBACH that includes dynamic vegetation, carbon cycle, and fire regime are used for simulation of natural fire dynamics through the last 8,000 years. To compare the fire model results with the charcoal reconstructions, several output variables of the fire model (burned area, carbon emissions) and several approaches of model output processing are tested. The z-scores out of charcoal dataset have been calculated for the period 8,000 to 200 BP to exclude a period of strong anthropogenic forcing during the last two centuries. The model analysis points mainly to an increasing fire activity during the Holocene for most of the investigated areas, which is in good correspondence to reconstructed fire trends out of charcoal data for most of the tested regions, while for few regions such as Europe the simulated trend and the reconstructed trends are different. The difference between the modeled and reconstructed fire activity could be due to absence of the anthropogenic forcing in the model simulations, but also due to limitations of model assumptions for modeling fire dynamics. For the model trends, the usage of averaging or z-score processing of model output resulted in similar directions of trend. Therefore, the approach of fire model output processing does not effect results of the model-data comparison. Global fire modeling is still in its infancy; improving our representations of fire through validation exercises such as what we present here is thus essential before testing hypotheses about the effects of extreme climate changes on fire behavior and potential feedbacks that result from those changes.

  15. Green Propulsion Auxiliary Power Unit Demonstration at MSFC

    NASA Technical Reports Server (NTRS)

    Robinson, Joel W.

    2014-01-01

    In 2012, the National Aeronautics & Space Administration (NASA) Space Technology Mission Directorate (STMD) began the process of building an integrated technology roadmap, including both technology pull and technology push strategies. Technology Area 1 (TA-01)1 for Launch Propulsion Systems is one of fourteen TAs that provide recommendations for the overall technology investment strategy and prioritization of NASA's space technology activities. Identified within TA-01 was the need for a green propulsion auxiliary power unit (APU) for hydraulic power by 2015. Engineers led by the author at the Marshall Space Flight Center (MSFC) have been evaluating green propellant alternatives and have begun the development of an APU test bed to demonstrate the feasibility of use. NASA has residual APU assets remaining from the retired Space Shuttle Program. Likewise, the F-16 Falcon fighter jet also uses an Emergency Power Unit (EPU) that has similar characteristics to the NASA hardware. Both EPU and APU components have been acquired for testing at MSFC. This paper will summarize the status of the testing efforts of green propellant from the Air Force Research Laboratory (AFRL) propellant AFM315E based on hydroxyl ammonium nitrate (HAN) with these test assets.

  16. Detection of hidden pre-industrial charcoal kilns by high-resolution LIDAR

    NASA Astrophysics Data System (ADS)

    Raab, Thomas; Raab, Alexandra; Nicolay, Alexander; Takla, Melanie; Rösler, Horst; Bönisch, Eberhard

    2013-04-01

    Over the last decade, systematic archaeological excavations in the open-cast mine Jänschwalde (Brandenburg, Germany) have revealed one of the largest, archaeologically excavated pre-industrial charcoal production area in Central Europe. Many of the charcoal kiln relics are easy to detect by survey as they lie close to the surface and charcoal pieces hint on their existence. In the excavations the remains of the charcoal kilns are distinct, black circles in the light-coloured sands. To date, in the former Königlich-Taubendorfer Forst c. 800 remains of charcoal hearths have been excavated and documented by archaeologists in an area of about 20 km2. Further c. 300 charcoal hearths are prospected by survey. Unfortunately, the spatial information about the charcoal kiln sites in Lower Lusatia (and elsewhere) is incomplete since we only have data from the archaeological excavation and prospection in the directly affected mining district. To fill this gap, we decided to test the applicability of Airborne Laser Scanning (ALS) data for charcoal kiln prospection. The particularly improved quality of the recent high-resolution light detection and ranging (LIDAR) data enabled the computer-aided detection of charcoal kilns and their evaluation using a geographical information system (GIS). Following data processing, the charcoal kilns are visible as buttons-like shapes in the shaded-relief maps (SRM). The characteristic shapes arise because the kiln plates are some centimetres to decimetres higher than the ditches around them. Numerous ground checks confirmed the applicability of the prospection by ALS data. But, we also assume that c. 10% of the charcoal kilns remain unidentified. A 26.6 km2 study area in the Tauerscher Forst, a forest about 10 km northwest of the open-cast mine Jänschwalde, was selected for prospection using a 1 m resolution ALS data set from the year 2011. Today, the area is forested with pine, and no archaeological excavation has been carried out so far

  17. Could charcoal filtration of cigarette smoke reduce smoking-induced disease? A review of the literature.

    PubMed

    Coggins, Christopher R E; Gaworski, Charles L

    2008-04-01

    A review of the published work with charcoal-filtered cigarettes indicates that there are reductions in the concentrations for many gas-vapor phase constituents found in mainstream smoke. However, charcoal filters provided no apparent capacity for reduction of smoke particulate phase components. The reductions in gas-vapor phase smoke chemistry analytes generally correspond with findings of reduced toxicological activity, principally related to a reduction in the cytotoxic action of the volatile smoke constituents. Results of a short-term clinical study show small reductions in the biomarkers of the gas-vapor phase smoke constituents in subjects smoking charcoal-filtered cigarettes, compared to subjects smoking non-charcoal filtered cigarettes. The very limited epidemiology data (a single study) fail to demonstrate a conclusive beneficial effect of charcoal-filtered cigarette products compared to non-charcoal filtered cigarette products. Review of the scientific literature is hindered due to the lack of documentation regarding the activity of the charcoal used in the filter, and the inconsistency in product designs used between the various different disciplines (chemistry, pre-clinical, clinical and epidemiology) that have conducted studies with charcoal filtered cigarettes. There do not appear to be any published studies using a combination of data from the different disciplines based on a consistently designed charcoal cigarette filter. Although the literature presently available would suggest that smoke filtration provided by current charcoal filter techniques alone may not be substantial enough to reduce smoking-related disease, the data are limited. Therefore, for the reduction of smoking-induced disease, it is difficult to come to a definitive conclusion regarding the potential health benefits of using charcoal as a smoke filtration technology. PMID:18289753

  18. A synthesis of parameters related to the binding of neutral organic compounds to charcoal.

    PubMed

    Hale, Sarah E; Arp, Hans Peter H; Kupryianchyk, Darya; Cornelissen, Gerard

    2016-02-01

    The sorption strength of neutral organic compounds to charcoal, also called biochar was reviewed and related to charcoal and compound properties. From 29 studies, 507 individual Freundlich sorption coefficients were compiled that covered the sorption strength of 107 organic contaminants. These sorption coefficients were converted into charcoal-water distribution coefficients (K(D)) at aqueous concentrations of 1 ng/L, 1 µg/L and 1 mg/L. Reported log K(D) values at 1 µg/L varied from 0.38 to 8.25 across all data. Variation was also observed within the compound classes; pesticides, herbicides and insecticides, PAHs, phthalates, halogenated organics, small organics, alcohols and PCBs. Five commonly reported variables; charcoal production temperature T, surface area SA, H/C and O/C ratios and organic compound octanol-water partitioning coefficient, were correlated with KD values using single and multiple-parameter linear regressions. The sorption strength of organic compounds to charcoals increased with increasing charcoal production temperature T, charcoal SA and organic pollutant octanol-water partitioning coefficient and decreased with increasing charcoal O/C ratio and charcoal H/C ratio. T was found to be correlated with SA (r(2) = 0.66) and O/C (r(2) = 0.50), particularly for charcoals produced from wood feedstocks (r(2) = 0.73 and 0.80, respectively). The resulting regression: log K(D)=(0.18 ± 0.06) log K(ow) + (5.74 ± 1.40) log T + (0.85 ± 0.15) log SA + (1.60 ± 0.29) log OC + (-0.89 ± 0.20) log HC + (-13.20 ± 3.69), r(2) = 0.60, root mean squared error = 0.95, n = 151 was obtained for all variables. This information can be used as an initial screening to identify charcoals for contaminated soil and sediment remediation. PMID:26347927

  19. A synthesis of parameters related to the binding of neutral organic compounds to charcoal.

    PubMed

    Hale, Sarah E; Arp, Hans Peter H; Kupryianchyk, Darya; Cornelissen, Gerard

    2016-02-01

    The sorption strength of neutral organic compounds to charcoal, also called biochar was reviewed and related to charcoal and compound properties. From 29 studies, 507 individual Freundlich sorption coefficients were compiled that covered the sorption strength of 107 organic contaminants. These sorption coefficients were converted into charcoal-water distribution coefficients (K(D)) at aqueous concentrations of 1 ng/L, 1 µg/L and 1 mg/L. Reported log K(D) values at 1 µg/L varied from 0.38 to 8.25 across all data. Variation was also observed within the compound classes; pesticides, herbicides and insecticides, PAHs, phthalates, halogenated organics, small organics, alcohols and PCBs. Five commonly reported variables; charcoal production temperature T, surface area SA, H/C and O/C ratios and organic compound octanol-water partitioning coefficient, were correlated with KD values using single and multiple-parameter linear regressions. The sorption strength of organic compounds to charcoals increased with increasing charcoal production temperature T, charcoal SA and organic pollutant octanol-water partitioning coefficient and decreased with increasing charcoal O/C ratio and charcoal H/C ratio. T was found to be correlated with SA (r(2) = 0.66) and O/C (r(2) = 0.50), particularly for charcoals produced from wood feedstocks (r(2) = 0.73 and 0.80, respectively). The resulting regression: log K(D)=(0.18 ± 0.06) log K(ow) + (5.74 ± 1.40) log T + (0.85 ± 0.15) log SA + (1.60 ± 0.29) log OC + (-0.89 ± 0.20) log HC + (-13.20 ± 3.69), r(2) = 0.60, root mean squared error = 0.95, n = 151 was obtained for all variables. This information can be used as an initial screening to identify charcoals for contaminated soil and sediment remediation.

  20. Packed Bed Reactor Experiment

    NASA Video Gallery

    The purpose of the Packed Bed Reactor Experiment in low gravity is to determine how a mixture of gas and liquid flows through a packed bed in reduced gravity. A packed bed consists of a metal pipe ...

  1. Concentrations and bioaccessibilities of trace elements in barbecue charcoals.

    PubMed

    Sharp, Annabel; Turner, Andrew

    2013-11-15

    Total and bioaccessible concentrations of trace elements (Al, As, Cd, Cu, Fe, Hg, Mn, Ni, Pb and Zn) have been measured in charcoals from 15 barbecue products available from UK retailers. Total concentrations (available to boiling aqua regia) were greater in briquetted products (with mean concentrations ranging from 0.16 μg g(-1) for Cd to 3240 μg g(-1) for Al) than in lumpwoods (0.007 μg g(-1) for Cd to 28 μg g(-1) for Fe), presumably because of the use of additives and secondary constituents (e.g. coal) in the former. On ashing, and with the exception of Hg, elemental concentrations increased by factors ranging from about 1.5 to 50, an effect attributed to the combustion of organic components and offset to varying extents by the different volatilities of the elements. Concentrations in the ashed products that were bioaccessible, or available to a physiologically based extraction test (PBET) that simulates, successively, the chemical conditions in the human stomach and intestine, exhibited considerable variation among the elements studied. Overall, however, bioaccessible concentrations relative to corresponding total concentrations were greatest for As, Cu and Ni (attaining 100% in either or both simulated PBET phases in some cases) and lowest for Pb (generally <1% in both phases). A comparison of bioaccessible concentrations in ashed charcoals with estimates of daily dietary intake suggest that Al and As are the trace elements of greatest concern to human health from barbecuing.

  2. Experimental Research of Pyrolysis Gases Cracking on Surface of Charcoal

    NASA Astrophysics Data System (ADS)

    Kosov, Valentin; Kosov, Vladimir; Zaichenko, Victor

    For several years, in the Joint Institute for High Temperatures of Russian Academy of Sciences, two-stage technology of biomass processing has been developing [1]. The technology is based on pyrolysis of biomass as the first stage. The second stage is high-temperature conversion of liquid fraction of the pyrolysis on the surface of porous charcoal matrix. Synthesis gas consisted of carbon monoxide and hydrogen is the main products of the technology. This gas is proposed to be used as fuel for gas-engine power plant. For practical implementation of the technology it is important to know the size of hot char filter for full cracking of the pyrolysis gases on the surface of charcoal. Theoretical determination of the cracking parameters of the pyrolysis gases on the surface of coal is extremely difficult because the pyrolysis gases include tars, whose composition and structure is complicated and depends on the type of initial biomass. It is also necessary to know the surface area of the char used in the filter, which is also a difficult task. Experimental determination of the hot char filter parameters is presented. It is shown that proposed experimental method can be used for different types of biomass.

  3. Carbon Sequestration and Fertility after Centennial Time Scale Incorporation of Charcoal into Soil

    PubMed Central

    Criscuoli, Irene; Alberti, Giorgio; Baronti, Silvia; Favilli, Filippo; Martinez, Cristina; Calzolari, Costanza; Pusceddu, Emanuela; Rumpel, Cornelia; Viola, Roberto; Miglietta, Franco

    2014-01-01

    The addition of pyrogenic carbon (C) in the soil is considered a potential strategy to achieve direct C sequestration and potential reduction of non-CO2 greenhouse gas emissions. In this paper, we investigated the long term effects of charcoal addition on C sequestration and soil physico-chemical properties by studying a series of abandoned charcoal hearths in the Eastern Alps of Italy established in the XIX century. This natural setting can be seen as an analogue of a deliberate experiment with replications. Carbon sequestration was assessed indirectly by comparing the amount of pyrogenic C present in the hearths (23.3±4.7 kg C m−2) with the estimated amount of charcoal that was left on the soil after the carbonization (29.3±5.1 kg C m−2). After taking into account uncertainty associated with parameters’ estimation, we were able to conclude that 80±21% of the C originally added to the soil via charcoal can still be found there and that charcoal has an overall Mean Residence Time of 650±139 years, thus supporting the view that charcoal incorporation is an effective way to sequester atmospheric CO2. We also observed an overall change in the physical properties (hydrophobicity and bulk density) of charcoal hearth soils and an accumulation of nutrients compared to the adjacent soil without charcoal. We caution, however, that our site-specific results should not be generalized without further study. PMID:24614647

  4. Some theoretical priciples of the activation of wood charcoal by steam

    SciTech Connect

    Fedoseev, A.S.

    1982-01-01

    Kinetics and diffusion in the pores of a carbonaceous material are considered. The macroscopic rate of the reaction of steam with the carbon of wood charcoal has been determined. The optimum conditions for the activation of wood charcoal have been found.

  5. Effect of charcoal amendment on adsorption, leaching and degradation of isoproturon in soils.

    PubMed

    Si, Youbin; Wang, Midao; Tian, Chao; Zhou, Jing; Zhou, Dongmei

    2011-04-01

    The effects of charcoal amendment on adsorption, leaching and degradation of the herbicide isoproturon in soils were studied under laboratory conditions. The adsorption data all fitted well with the Freundlich empirical equation. It was found that the adsorption of isoproturon in soils increased with the rate of charcoal amended (correlation coefficient r=0.957**, P<0.01). The amount of isoproturon in leachate decreased with the increase of the amount of charcoal addition to soil column, while the retention of isoproturon in soils increased with an increase in the charcoal content of soil samples. Biodegradation was still the most significant mechanism for isoproturon dissipation from soil. Charcoal amendment greatly reduced the biodegradation of isoproturon in soils. The half-lives of isoproturon degradation (DT(50)) in soils greatly extended when the rate of added charcoal increased from 0 to 50 g kg(-1) (for Paddy soil, DT(50) values increased from 54.6 to 71.4 days; for Alfisol, DT(50) from 16.0 to 136 days; and for Vertisol, DT(50) from 15.2 to 107 days). The degradation rate of isoproturon in soils was significantly negatively correlated with the amount of added charcoal. This research suggests that charcoal amendment may be an effective management practice for reducing pesticide leaching and enhancing its persistence in soils.

  6. Rapid spread of suicide by charcoal burning from 2007 to 2011 in Korea.

    PubMed

    Lee, Ah-Rong; Ahn, Myung Hee; Lee, Tae Yeop; Park, Subin; Hong, Jin Pyo

    2014-11-30

    Despite rapid increase of suicide by charcoal burning within 5 years, little is known about the characteristics of charcoal burning suicide in Korea. This study aimed to examine the trends and risk factors in the spread of suicide using this method. We identified an association between media reporting of suicide by charcoal burning and its incidence. Data on suicide from 2007 to 2011 were obtained from the Korean National Statistical Office. Cross-correlation analysis was used. Increasing incidence of suicide by charcoal burning was correlated with higher education levels, male sex, and the latter half of the year. Victims of charcoal burning suicide were more likely to be young, male, single, highly educated, professional, urban-based, and to die between October and December. Internet reports of suicide via charcoal burning tended to precede the increased incidence of suicide using this method, but only during the early period of the suicide epidemic. Our findings suggest that one episode of heavy media coverage of a novel method, such as charcoal burning, is sufficient to increase the prevalence of suicide by that method even after media coverage decreases. These findings are expected to contribute to the prevention of increasing rates of suicide by charcoal burning.

  7. Effects of carbonization parameters of Moso-bamboo-based porous charcoal on capturing carbon dioxide.

    PubMed

    Huang, Pei-Hsing; Jhan, Jhih-Wei; Cheng, Yi-Ming; Cheng, Hau-Hsein

    2014-01-01

    This study experimentally analyzed the carbon dioxide adsorption capacity of Moso-bamboo- (Phyllostachys edulis-) based porous charcoal. The porous charcoal was prepared at various carbonization temperatures and ground into powders with 60, 100, and 170 meshes, respectively. In order to understand the adsorption characteristics of porous charcoal, its fundamental properties, namely, charcoal yield, ash content, pH value, Brunauer-Emmett-Teller (BET) surface area, iodine number, pore volume, and powder size, were analyzed. The results show that when the carbonization temperature was increased, the charcoal yield decreased and the pH value increased. Moreover, the bamboo carbonized at a temperature of 1000(°)C for 2 h had the highest iodine sorption value and BET surface area. In the experiments, charcoal powders prepared at various carbonization temperatures were used to adsorb 1.854% CO2 for 120 h. The results show that the bamboo charcoal carbonized at 1000(°)C and ground with a 170 mesh had the best adsorpt on capacity, significantly decreasing the CO2 concentration to 0.836%. At room temperature and atmospheric pressure, the Moso-bamboo-based porous charcoal exhibited much better CO2 adsorption capacity compared to that of commercially available 350-mesh activated carbon.

  8. The effect of weathering on charcoal filter performance. 1; The adsorption and desorption behavior of contaminants

    SciTech Connect

    Wren, J.C.; Moore, C.J. )

    1991-05-01

    This paper reports on triethylenediamine (TEDA) impregnated charcoals, used in nuclear reactors to safeguard against the release of airborne radioiodine, which show high efficiency under various reactor operation and accident conditions when the are new. However, during normal operation, charcoal filters are continuously degraded (or weathered) due to the adsorption of moisture and other air contaminants. The effect of weathering on the efficiency of charcoal for removing radioiodine is of great interest. The results of a study on the adsorption behavior of various contaminants NO{sub 2}, SO{sub 2} 2-butanone (methyl-ethyl ketone (MEK)) and NH{sub 3} on TEDA charcoal are presented. This study is an attempt to characterize and quantify the weathering process of TEDA charcoal by these contaminants. The adsorption and desorption of characteristics of these contaminants range from completely irreversible (NO{sub 2}) to completely reversible (NH{sub 3}). The effect of absorbed water (or humidity) on absorption is different for each contaminant. Absorbed water increases the absorption rate and capacity of TEDA charcoal for NO{sub 2}. However, it appears that SO{sub 2} is absorbed as H{sub 2}SO{sub 4} on the wet charcoal. Absorbed water slightly reduces the adsorption capacity of the charcoal for MEK, but does not affect the absorption of NH{sub 3}.

  9. Potassium and phosphorus effects on disease severity of charcoal rot of soybean

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The effects of potassium (K) and phosphorus (P) fertilizers on charcoal rot of soybean [Glycine max (L.) Merr.] are unknown. Therefore, the severity of charcoal rot was studied at five levels of K (0, 37, 75, 111 and 149 kg K ha-1) and a level that was equal to the recommended fertilizer applicatio...

  10. Carbon sequestration and fertility after centennial time scale incorporation of charcoal into soil.

    PubMed

    Criscuoli, Irene; Alberti, Giorgio; Baronti, Silvia; Favilli, Filippo; Martinez, Cristina; Calzolari, Costanza; Pusceddu, Emanuela; Rumpel, Cornelia; Viola, Roberto; Miglietta, Franco

    2014-01-01

    The addition of pyrogenic carbon (C) in the soil is considered a potential strategy to achieve direct C sequestration and potential reduction of non-CO2 greenhouse gas emissions. In this paper, we investigated the long term effects of charcoal addition on C sequestration and soil physico-chemical properties by studying a series of abandoned charcoal hearths in the Eastern Alps of Italy established in the XIX century. This natural setting can be seen as an analogue of a deliberate experiment with replications. Carbon sequestration was assessed indirectly by comparing the amount of pyrogenic C present in the hearths (23.3±4.7 kg C m(-2)) with the estimated amount of charcoal that was left on the soil after the carbonization (29.3±5.1 kg C m(-2)). After taking into account uncertainty associated with parameters' estimation, we were able to conclude that 80±21% of the C originally added to the soil via charcoal can still be found there and that charcoal has an overall Mean Residence Time of 650±139 years, thus supporting the view that charcoal incorporation is an effective way to sequester atmospheric CO2. We also observed an overall change in the physical properties (hydrophobicity and bulk density) of charcoal hearth soils and an accumulation of nutrients compared to the adjacent soil without charcoal. We caution, however, that our site-specific results should not be generalized without further study.

  11. ESTIMATION OF EMISSIONS FROM CHARCOAL LIGHTER FLUID AND REVIEW OF ALTERNATIVES

    EPA Science Inventory

    The report gives results of an evaluation of emissions of volatile organic compounds (VOCs) from charcoal lighter fluid, a consumer product consisting entirely of volatile constituents. An estimated 46,250 tons (42,000 Mg) of charcoal lighter fluid is used in the U.S. each year. ...

  12. Commercial charcoal production in the Ibarapa district of southwestern Nigeria: forestry dividends and welfare implications.

    PubMed

    Salami, Kabiru K; Brieger, William R

    2010-01-01

    Logging activities have long provided both wood fuel and charcoal for household and commercial use in rural and urban communities in developing countries. However, logging problems range from deforestation to threatened household air quality from burning wood and charcoal. This exploratory case study triangulated 15 in-depth interviews among charcoal bulk buyers and the workers, observations of workers at two èédú (charcoal) commercial depots in Igbo-Ora and of workers in the forest, and review of studies in academic database. Three categories of people are working in the business ranging from the producers in the forests (alaake) to the bulk buyers (olowo) in the middle and the wholesalers (ajagunta) in the city. A small team of 4-8 people can produce three pickup truck loads of charcoal in 2 weeks, and a large team between 7-8 loads. The olowo and the alaake have associations, membership cards, and meet to discuss business progress and regulate members' economic behavior. Close to 35,000 bags of charcoal of 450 pickup trucks may make the journey weekly from Ibarapa. Overall, the charcoal business is informal, and the local people also frown at cutting any useful indigenous trees ascertaining that an individual's actions may affect the whole community. The role of community health educators is important in the dissemination of effects of deforestation through charcoal production.

  13. Effect of charcoal amendment on adsorption, leaching and degradation of isoproturon in soils

    NASA Astrophysics Data System (ADS)

    Si, Youbin; Wang, Midao; Tian, Chao; Zhou, Jing; Zhou, Dongmei

    2011-04-01

    The effects of charcoal amendment on adsorption, leaching and degradation of the herbicide isoproturon in soils were studied under laboratory conditions. The adsorption data all fitted well with the Freundlich empirical equation. It was found that the adsorption of isoproturon in soils increased with the rate of charcoal amended (correlation coefficient r = 0.957 **, P < 0.01). The amount of isoproturon in leachate decreased with the increase of the amount of charcoal addition to soil column, while the retention of isoproturon in soils increased with an increase in the charcoal content of soil samples. Biodegradation was still the most significant mechanism for isoproturon dissipation from soil. Charcoal amendment greatly reduced the biodegradation of isoproturon in soils. The half-lives of isoproturon degradation ( DT50) in soils greatly extended when the rate of added charcoal inceased from 0 to 50 g kg - 1 (for Paddy soil, DT50 values increased from 54.6 to 71.4 days; for Alfisol, DT50 from 16.0 to 136 days; and for Vertisol, DT50 from 15.2 to 107 days). The degradation rate of isoproturon in soils was significantly negatively correlated with the amount of added charcoal. This research suggests that charcoal amendment may be an effective management practice for reducing pesticide leaching and enhancing its persistence in soils.

  14. URINARY MUTAGENICITY IN CHARCOAL WORKERS: A CROSS-SECTIONAL STUDY IN NORTHEASTERN BRAZIL

    EPA Science Inventory

    Urinary Mutagenicity in charcoal workers: a cross-sectional study in northeastern Brazil

    Charcoal production by wood carbonization is an ancient process that has changed little since the Bronze Age. Its production in large scale is necessary to sustain some steel and pig...

  15. Carbon sequestration and fertility after centennial time scale incorporation of charcoal into soil.

    PubMed

    Criscuoli, Irene; Alberti, Giorgio; Baronti, Silvia; Favilli, Filippo; Martinez, Cristina; Calzolari, Costanza; Pusceddu, Emanuela; Rumpel, Cornelia; Viola, Roberto; Miglietta, Franco

    2014-01-01

    The addition of pyrogenic carbon (C) in the soil is considered a potential strategy to achieve direct C sequestration and potential reduction of non-CO2 greenhouse gas emissions. In this paper, we investigated the long term effects of charcoal addition on C sequestration and soil physico-chemical properties by studying a series of abandoned charcoal hearths in the Eastern Alps of Italy established in the XIX century. This natural setting can be seen as an analogue of a deliberate experiment with replications. Carbon sequestration was assessed indirectly by comparing the amount of pyrogenic C present in the hearths (23.3±4.7 kg C m(-2)) with the estimated amount of charcoal that was left on the soil after the carbonization (29.3±5.1 kg C m(-2)). After taking into account uncertainty associated with parameters' estimation, we were able to conclude that 80±21% of the C originally added to the soil via charcoal can still be found there and that charcoal has an overall Mean Residence Time of 650±139 years, thus supporting the view that charcoal incorporation is an effective way to sequester atmospheric CO2. We also observed an overall change in the physical properties (hydrophobicity and bulk density) of charcoal hearth soils and an accumulation of nutrients compared to the adjacent soil without charcoal. We caution, however, that our site-specific results should not be generalized without further study. PMID:24614647

  16. Potassium and Phosphorus effects on disease severity of charcoal rot of soybean

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The effects of potassium (K) and phosphorus (P) fertilizers on charcoal rot of soybean [Glycine max (L.) Merr.] are unknown. Therefore, the severity of charcoal rot was studied at five levels of K (0, 37, 75, 111 and 149 kg K ha-1) and a level that was equal to the recommended fertilizer applicatio...

  17. Digital image processing applications in the ignition and combustion of char/coal particles

    SciTech Connect

    Annamalai, K.; Kharbat, E.; Goplakrishnan, C.

    1992-12-01

    Digital image processing, is employed in this remarch study in order to visually investigate the ignition and combustion characteristics of isolated char/coal particles as well as the effect of interactivecombustion in two-particle char/coal arrays. Preliminary experiments are conducted on miniature isolated candles as well as two-candle arrays.

  18. Water adsorption on charcoal: New approach in experimental studies and data representation

    SciTech Connect

    Geynisman, M.; Walker, R.

    1991-08-01

    The experimental apparatus was built to study the H{sub 2}O adsorption on charcoal at very low concentrations and collect the data in the form of isosteres. Experimental method is discussed and the global three-dimensional fit is constructed to predict the post-regeneration conditions of charcoal absorbers. 11 refs.

  19. Effects of Carbonization Parameters of Moso-Bamboo-Based Porous Charcoal on Capturing Carbon Dioxide

    PubMed Central

    Jhan, Jhih-Wei; Cheng, Yi-Ming; Cheng, Hau-Hsein

    2014-01-01

    This study experimentally analyzed the carbon dioxide adsorption capacity of Moso-bamboo- (Phyllostachys edulis-) based porous charcoal. The porous charcoal was prepared at various carbonization temperatures and ground into powders with 60, 100, and 170 meshes, respectively. In order to understand the adsorption characteristics of porous charcoal, its fundamental properties, namely, charcoal yield, ash content, pH value, Brunauer-Emmett-Teller (BET) surface area, iodine number, pore volume, and powder size, were analyzed. The results show that when the carbonization temperature was increased, the charcoal yield decreased and the pH value increased. Moreover, the bamboo carbonized at a temperature of 1000°C for 2 h had the highest iodine sorption value and BET surface area. In the experiments, charcoal powders prepared at various carbonization temperatures were used to adsorb 1.854% CO2 for 120 h. The results show that the bamboo charcoal carbonized at 1000°C and ground with a 170 mesh had the best adsorption capacity, significantly decreasing the CO2 concentration to 0.836%. At room temperature and atmospheric pressure, the Moso-bamboo-based porous charcoal exhibited much better CO2 adsorption capacity compared to that of commercially available 350-mesh activated carbon. PMID:25225639

  20. [Hospital auxiliary staff, between polyvalence and invisibility].

    PubMed

    Veissier, Pascale

    2016-01-01

    Often underestimated, hospital auxiliary staff carry out on a daily basis a professional activity that may be difficult to define and/or recognize. What does their work consist in and what are the boundaries of the scope of their activity? Faced with a growing rate of absenteeism among these members of staff in a nursing home for elderly people attached to a hospital, an issue emerges: does the content of their professional activity have an impact on the causes and evolution of this phenomenon? PMID:26976318

  1. Auxiliary engine digital interface unit (DIU)

    NASA Technical Reports Server (NTRS)

    1972-01-01

    This auxiliary propulsion engine digital unit controls both the valving of the fuel and oxidizer to the engine combustion chamber and the ignition spark required for timely and efficient engine burns. In addition to this basic function, the unit is designed to manage it's own redundancy such that it is still operational after two hard circuit failures. It communicates to the data bus system several selected information points relating to the operational status of the electronics as well as the engine fuel and burning processes.

  2. Space Shuttle Orbiter auxiliary power unit

    NASA Technical Reports Server (NTRS)

    Mckenna, R.; Wicklund, L.; Baughman, J.; Weary, D.

    1982-01-01

    The Space Shuttle Orbiter auxiliary power units (APUs) provide hydraulic power for the Orbiter vehicle control surfaces (rudder/speed brake, body flap, and elevon actuation systems), main engine gimbaling during ascent, landing gear deployment and steering and braking during landing. Operation occurs during launch/ascent, in-space exercise, reentry/descent, and landing/rollout. Operational effectiveness of the APU is predicated on reliable, failure-free operation during each flight, mission life (reusability) and serviceability between flights (turnaround). Along with the accumulating flight data base, the status and results of efforts to achieve these long-run objectives is presented.

  3. Heat exchanger with auxiliary cooling system

    DOEpatents

    Coleman, John H.

    1980-01-01

    A heat exchanger with an auxiliary cooling system capable of cooling a nuclear reactor should the normal cooling mechanism become inoperable. A cooling coil is disposed around vertical heat transfer tubes that carry secondary coolant therethrough and is located in a downward flow of primary coolant that passes in heat transfer relationship with both the cooling coil and the vertical heat transfer tubes. A third coolant is pumped through the cooling coil which absorbs heat from the primary coolant which increases the downward flow of the primary coolant thereby increasing the natural circulation of the primary coolant through the nuclear reactor.

  4. System Study: Auxiliary Feedwater 1998–2013

    SciTech Connect

    Schroeder, John Alton

    2014-12-31

    This report presents an unreliability evaluation of the auxiliary feedwater (AFW) system at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2013 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10-year period, while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the AFW results.

  5. Hydrogen/oxygen auxiliary propulsion technology

    NASA Technical Reports Server (NTRS)

    Reed, Brian D.; Schneider, Steven J.

    1991-01-01

    A survey is provided of hydrogen/oxygen (H/O) auxiliary propulsion system (APS) concepts and low thrust H/O rocket technology. A review of H/O APS studies performed for the Space Shuttle, Space Tug, Space Station Freedom, and Advanced Manned Launch System programs is given. The survey also includes a review of low thrust H/O rocket technology programs, covering liquid H/O and gaseous H/O thrusters, ranging from 6600 N (1500 lbf) to 440 mN (0.1 lbf) thrust. Ignition concepts for H/O thrusters and high temperature, oxidation resistant chamber materials are also reviewed.

  6. System Study: Auxiliary Feedwater 1998-2014

    SciTech Connect

    Schroeder, John Alton

    2015-12-01

    This report presents an unreliability evaluation of the auxiliary feedwater (AFW) system at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2014 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10 year period, while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the AFW results.

  7. Charcoal produced by prescribed fire increases dissolved organic carbon and soil microbial activity

    NASA Astrophysics Data System (ADS)

    Poon, Cheryl; Jenkins, Meaghan; Bell, Tina; Adams, Mark

    2014-05-01

    In Australian forests fire is an important driver of carbon (C) storage. When biomass C is combusted it is transformed into vegetation residue (charcoal) and deposited in varying amounts and forms onto soil surfaces. The C content of charcoal is high but is largely in a chemically stable form of C, which is highly resistance to microbial decomposition. We conducted two laboratory incubations to examine the influence of charcoal on soil microbial activity as indicated by microbial respiration. Seven sites were chosen in mixed species eucalypt forest in Victoria, Australia. Soil was sampled prior to burning to minimise the effects of heating or addition of charcoal during the prescribed burn. Charcoal samples were collected from each site after the burn, homogenised and divided into two size fractions. Prior to incubation, soils were amended with the two size fractions (<1 and 1-4.75 mm) and at two rates of amount (2.5 and 5% by soil dry weight). Charcoal-amended soils were incubated in the laboratory for 86 d, microbial respiration was measured nine times at day 1, 3, 8, 15, 23, 30, 45, 59 and 86 d. We found that addition of charcoal resulted in faster rates of microbial respiration compared to unamended soil. Fastest rates of microbial respiration in all four treatments were measured 1 d after addition of charcoal (up to 12 times greater than unamended soil). From 3 to 8 d, respiration rates in all four treatments decreased and only treatments with greater charcoal addition (5%) remained significantly faster than unamended soil. From 15 d to 86 d, all treatments had respiration rates similar to unamended soil. Overall, adding greater amount of charcoal (5%) resulted in a larger cumulative amount of CO2 released over the incubation period when compared to unamended soil. The second laboratory incubation focused on the initial changes in soil nutrient and microbial respiration after addition of charcoal over a 72 h period. Charcoal (<2 mm) was added at rate of 5% to

  8. Molecular Marker Approach on Characterizing and Quantifying Charcoal in Environmental Media

    NASA Astrophysics Data System (ADS)

    Kuo, L.; Herbert, B. E.; Louchouarn, P.

    2006-12-01

    Black carbon (BC) is widely distributed in natural environments including soils, sediments, freshwater, seawater and the atmosphere. It is produced mostly from the incomplete combustion of fossil fuels and vegetation. In recent years, increasing attention has been given to BC due to its potential influence in many biogeochemical processes. In the environment, BC exists as a continuum ranging from partly charred plant materials, charcoal residues to highly condensed soot and graphite particles. The heterogeneous nature of black carbon means that BC is always operationally-defined, highlighting the need for standard methods that support data comparisons. Unlike soot and graphite that can be quantified with well-established methods, it is difficult to directly quantify charcoal in geologic media due to its chemical and physical heterogeneity. Most of the available charcoal quantification methods detect unknown fractions of the BC continuum. To specifically identify and quantify charcoal in soils and sediments, we adopted and validated an innovative molecular marker approach that quantifies levoglucosan, a pyrogenic derivative of cellulose, as a proxy of charcoal. Levoglucosan is source-specific, stable and is able to be detected at low concentrations using gas chromatograph-mass spectrometer (GC-MS). In the present study, two different plant species, honey mesquite and cordgrass, were selected as the raw materials to synthesize charcoals. The lab-synthesize charcoals were made under control conditions to eliminate the high heterogeneity often found in natural charcoals. The effects of two major combustion factors, temperature and duration, on the yield of levoglucosan were characterized in the lab-synthesize charcoals. Our results showed that significant levoglucosan production in the two types of charcoal was restricted to relatively low combustion temperatures (150-350 degree C). The combustion duration did not cause significant differences in the yield of

  9. Towards an improvement of carbon accounting for wildfires: incorporation of charcoal production into carbon emission models

    NASA Astrophysics Data System (ADS)

    Doerr, Stefan H.; Santin, Cristina; de Groot, Bill

    2015-04-01

    Every year fires release to the atmosphere the equivalent to 20-30% of the carbon (C) emissions from fossil fuel consumption, with future emissions from wildfires expected to increase under a warming climate. Critically, however, part of the biomass C affected by fire is not emitted during burning, but converted into charcoal, which is very resistant to environmental degradation and, thus, contributes to long-term C sequestration. The magnitude of charcoal production from wildfires as a long-term C sink remains essentially unknown and, to the date, charcoal production has not been included in wildfire emission and C budget models. Here we present complete inventories of charcoal production in two fuel-rich, but otherwise very different ecosystems: i) a boreal conifer forest (experimental stand-replacing crown fire; Canada, 2012) and a dry eucalyptus forest (high-intensity fuel reduction burn; Australia 2014). Our data show that, when considering all the fuel components and quantifying all the charcoal produced from each (i.e. bark, dead wood debris, fine fuels), the overall amount of charcoal produced is significant: up to a third of the biomass C affected by fire. These findings indicate that charcoal production from wildfires could represent a major and currently unaccounted error in the estimation of the effects of wildfires in the global C balance. We suggest an initial approach to include charcoal production in C emission models, by using our case study of a boreal forest fire and the Canadian Fire Effects Model (CanFIRE). We also provide recommendations of how a 'conversion factor' for charcoal production could be relatively easily estimated when emission factors for different types of fuels and fire conditions are experimentally obtained. Ultimately, this presentation is a call for integrative collaboration between the fire emission modelling community and the charcoal community to work together towards the improvement of C accounting for wildfires.

  10. Towards an inventory of historic charcoal production fields in Brandenburg, Germany

    NASA Astrophysics Data System (ADS)

    Schneider, Anna; Takla, Melanie; Raab, Alexandra; Raab, Thomas; Bonhage, Alexander; Hirsch, Florian; Rösler, Horst

    2015-04-01

    The historic production of charcoal is an important component of the late Holocene fire history for many landscapes. Charcoal production can have numerous effects on ecosystems, e.g., through changes in forest area and structure, or through the effects of pyrolysis, charcoal and ash addition to soils. To assess such effects, it is necessary to understand the spatial extent and patterns of historic charcoal production, which has so far hardly been approached for the Northern European Lowlands. In the forefield of the open-cast mine Jänschwalde (north of Cottbus, Germany), archaeological excavations have revealed one of the largest charcoal production fields described so far. For this area, we applied and evaluated different methods for mapping the spatial distribution of charcoal kiln remains. Based on our results from this exceptionally well-described charcoal production field, we attempted to detect and map other large occurrences of charcoal kiln remains in the state of Brandenburg. For the mine forefield, archaeological excavations provide certain and exact information on kiln site location and geometry. Using airborne laser scanning elevation models, the mapping of kiln sites could be extended to areas beyond the mine forefield, using a manual digitization for thorough mapping in forest areas north of Cottbus, and an automated mapping approach for detection of kiln sites for additional areas in Brandenburg. Potential areas of large-scale production were identified in a GIS-based analysis of environmental and historic data. By manual digitization from Shaded Relief Maps, more than 5000 kiln sites in an area of 32 km2 were detected in the Jänschwalde mine forefield. First results of mapping for larger areas indicate similar densities, but smaller diameters of kiln sites in other charcoal production fields; and show that charcoal production is a so far underestimated component of the land use history in many parts of the Northern European Lowlands.

  11. Removal of furan and phenolic compounds from simulated biomass hydrolysates by batch adsorption and continuous fixed-bed column adsorption methods.

    PubMed

    Lee, Sang Cheol; Park, Sunkyu

    2016-09-01

    It has been proposed to remove all potential inhibitors and sulfuric acid in biomass hydrolysates generated from dilute-acid pretreatment of biomass, based on three steps of sugar purification process. This study focused on its first step in which furan and phenolic compounds were selectively removed from the simulated hydrolysates using activated charcoal. Batch adsorption experiments demonstrated that the affinity of activated charcoal for each component was highest in the order of vanillic acid, 4-hydroxybenzoic acid, furfural, acetic acid, sulfuric acid, and xylose. The affinity of activated charcoal for furan and phenolic compounds proved to be significantly higher than that of the other three components. Four separation strategies were conducted with a combination of batch adsorption and continuous fixed-bed column adsorption methods. It was observed that xylose loss was negligible with near complete removal of furan and phenolic compounds, when at least one fixed-bed column adsorption was implemented in the strategy. PMID:27289057

  12. Auxiliary propulsion requirements for large space systems

    NASA Technical Reports Server (NTRS)

    Maloy, J. E.; Smith, W. W.; Machles, G. W.

    1983-01-01

    An insight into auxiliary propulsion systems (APS) requirements for large space systems (LSS) launchable by a single shuttle is presented. In an effort to scope the APS requirements for LSS, a set of generic LSSs were defined. For each generic LSS class a specific structural configuration, representative of that most likely to serve the needs of the 1980's and 1990's was defined. The environmental disturbance forces and torques which would be acting on each specific structural configuration in LEO and GEO orbits were then determined. Auxiliary propulsion requirements were determined as a function of: generic class specific configuration, size and openness of structure, orbit, angle of orientation, correction frequency, duty cycle, number and location of thrusters and direction of thrusters and APS/LSS interactions. The results of this analysis were used to define the APS characteristics of: (1) number and distribution of thrusters, (2) thruster modulation, (3) thrust level, (4) mission energy requirements, (5) total APS mass component breakdown, and (6) state of the art adequacy/deficiency.

  13. Duality relations in the auxiliary field method

    SciTech Connect

    Silvestre-Brac, Bernard

    2011-05-15

    The eigenenergies {epsilon}{sup (N)}(m;{l_brace}n{sub i}, l{sub i{r_brace}}) of a system of N identical particles with a mass m are functions of the various radial quantum numbers n{sub i} and orbital quantum numbers l{sub i}. Approximations E{sup (N)}(m;Q) of these eigenenergies, depending on a principal quantum number Q({l_brace}n{sub i}, l{sub i{r_brace}}), can be obtained in the framework of the auxiliary field method. We demonstrate the existence of numerous exact duality relations linking quantities E{sup (N)}(m;Q) and E{sup (p)}(m';Q') for various forms of the potentials (independent of m and N) and for both nonrelativistic and semirelativistic kinematics. As the approximations computed with the auxiliary field method can be very close to the exact results, we show with several examples that these duality relations still hold, with sometimes a good accuracy, for the exact eigenenergies {epsilon}{sup (N)}(m;{l_brace}n{sub i}, l{sub i{r_brace}}).

  14. Auxiliary pattern for cell-based OPC

    NASA Astrophysics Data System (ADS)

    Kahng, Andrew B.; Park, Chul-Hong

    2006-10-01

    The runtime of model-based optical proximity correction (OPC) tools has grown unacceptably with each successive technology generation, and has emerged as one of the major bottlenecks for turnaround time (TAT) of IC data preparation and manufacturing. The cell-based OPC approach improves runtime by performing OPC once per cell definition as opposed to once per cell instantiation in the layout. However, cell-based OPC does not comprehend inter-cell optical interactions that affect feature printability in a layout context. In this work, we propose auxiliary pattern-enabled cell-based OPC which can minimize the CD differences between cell-based OPC and model-based OPC. To enable effective insertion of auxiliary pattern (AP) in the design, we also propose a post-placement optimization of a standard cell block with respect to detailed placement. By dynamic programming-based placement perturbation, we achieve 100% AP applicability in designs with placement utilizations of < 70%. In an evaluation with a complete industrial flow, cell-based OPC with AP can match gate edge placement error (EPE) count of model-based OPC within 4%. This is an improvement of 90%, on average, over cell-based OPC without APs. The AP-based OPC approach can reduce OPC runtimes versus model-based OPC by up to 40X in our benchmark designs. We can also achieve reduction of GDSII file size and ORC runtimes due to hierarchy maintenance of cell-based OPC.

  15. Interior room within eastern lift span, showing auxiliary electric and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Interior room within eastern lift span, showing auxiliary electric and gas generators. - Connecticut Avenue Bridge, Spans Rock Creek & Potomac Parkway at Connecticut Avenue, Washington, District of Columbia, DC

  16. Interior room within eastern lift span, showing auxiliary electric generator. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Interior room within eastern lift span, showing auxiliary electric generator. - Arlington Memorial Bridge, Spanning Potomac River between Lincoln Memorial & Arlington National Cemetery, Washington, District of Columbia, DC

  17. [Research progress in HIV auxiliary proteins counteracting host restriction factors].

    PubMed

    Chen, Qian-Qian; Xu, Qing-Gang; Zhang, Chi-Yu

    2014-01-01

    Identification and functional analyses of antiviral restriction factors in hosts have become hot research topics. Four HIV restriction factors, APOBEC3G, Trim5alpha, Tetherin, and SAMHD1, have been identified in recent years. By encoding auxiliary proteins, lentiviruses can counteract host restriction factors. For example, the auxiliary proteins Vif, Vpu, and Vpx of HIV antagonize APOBEC3G, Tetherin, and SAMHD1, respectively. Furthermore, these auxiliary proteins enable the entry of HIV into host cells and influence the replication and pathogenicity of HIV. In this paper, we review the research progress in the functions of the three HIV auxiliary proteins that can antagonize the host restriction factors.

  18. Soil charcoal from the plains to tundra in the Colorado Front Range

    NASA Astrophysics Data System (ADS)

    Sanford, R. L.; Licata, C.

    2010-12-01

    Throughout the forests of the central Rockies, soil charcoal from Holocene wildfires has been produced in response to wildland natural fire regimes. The extent and spatial distribution of soil charcoal production is poorly documented in this region, especially with regard to forests and shrublands at different elevations. Soil charcoal is a super-passive C pool derived from woody biomass that can be sequestered for millennia in forest soils. Recent research indicates that soil charcoal may promote enhanced soil fertility. Additionally, soil charcoal is an often overlooked component of soil C mass and flux. We hypothesize that differences in forest and shrubland fire regimes over the millennia have resulted in different soil charcoal amounts. Geospatial data were used to locate random sample plots in foothills shrublands (Cercocarpus montanus), and four forest types; ponderosa pine (Pinus ponderosa), Douglas-fir (Pseudotsuga menziesii), lodgepole pine (Pinus contorta) and spruce-fir (Picea engelmannii - Abies lasiocarpa). Sample plots were stratified to occur with the mid 200 m elevation band of each vegetation type with east aspect, and 10-30% slope. Soils were sampled widely at 0-10 cm depth and analyzed for total soil C and soil charcoal C via chemical digestion and dry combustion techniques. Overall, soil charcoal is four times more abundant in spruce-fir forests than in foothills shrublands (1.9 +/- 0.92 Mg C/ha versus 0.54 +/- 0.44 Mg C/ha). Soil charcoal is also abundant in lodgepole pine and ponderosa pine soils (1.4 +/- 1.02 Mg C/ha and 1.4 +/- 0.54 Mg C/ha respectively) but is less plentiful in Douglas-fir soils (1.0 +/- 0.67). Spruce-fir forests have the most above ground biomass, slower decomposition rates and a less frequent mean fire return interval than the other four forests, hence it makes sense that high per-fire rates of charcoal production would occur in the spruce-fir zone, given large amounts of surface fuels at the time of fire. In contrast

  19. [Caring for families of charcoal-burning suicide patients].

    PubMed

    Pien, Feng-Chen; Feng, Hsin-Pei; Tzeng, Wen-Chii

    2013-12-01

    Charcoal-burning is the second major cause of suicide death in Taiwan. Predicting the variable damage and sequelae in this suicide mode is difficult due to the rapid combination of carbon monoxide with red blood cells. Delayed neuropsychological sequelae (DNS) may result in significantly extended recovery times, causing additional stress to the family. Nurses may help increase family understanding and support and guide family members to more positive intra-family interactions, shared perspectives on the recovery process, and resource seeking behavior by depicting subsequent family life and helping the entire family develop coping strategies those allow all members to effect cognitive, emotional and behavioral change. This result may help families of attempted suicide individuals recover successfully.

  20. The impact of charcoal production on forest degradation: a case study in Tete, Mozambique

    NASA Astrophysics Data System (ADS)

    Sedano, F.; Silva, J. A.; Machoco, R.; Meque, C. H.; Sitoe, A.; Ribeiro, N.; Anderson, K.; Ombe, Z. A.; Baule, S. H.; Tucker, C. J.

    2016-09-01

    Charcoal production for urban energy consumption is a main driver of forest degradation in sub Saharan Africa. Urban growth projections for the continent suggest that the relevance of this process will increase in the coming decades. Forest degradation associated to charcoal production is difficult to monitor and commonly overlooked and underrepresented in forest cover change and carbon emission estimates. We use a multitemporal dataset of very high-resolution remote sensing images to map kiln locations in a representative study area of tropical woodlands in central Mozambique. The resulting maps provided a characterization of the spatial extent and temporal dynamics of charcoal production. Using an indirect approach we combine kiln maps and field information on charcoal making to describe the magnitude and intensity of forest degradation linked to charcoal production, including aboveground biomass and carbon emissions. Our findings reveal that forest degradation associated to charcoal production in the study area is largely independent from deforestation driven by agricultural expansion and that its impact on forest cover change is in the same order of magnitude as deforestation. Our work illustrates the feasibility of using estimates of urban charcoal consumption to establish a link between urban energy demands and forest degradation. This kind of approach has potential to reduce uncertainties in forest cover change and carbon emission assessments in sub-Saharan Africa.

  1. Comparison of activated charcoal and ipecac syrup in prevention of drug absorption.

    PubMed

    Neuvonen, P J; Vartiainen, M; Tokola, O

    1983-01-01

    The efficacy of activated charcoal and ipecac syrup in the prevention of drug absorption was studied in 6 healthy adult volunteers, using a randomized, cross-over design. Paracetamol 1000 mg, tetracycline 500 mg and aminophylline 350 mg were ingested on an empty stomach with 100 ml water. Then, after 5 or 30 min, the subjects ingested, either activated charcoal suspension (50 g charcoal), syrup of ipecac, or, only after 5 min, water 300 ml. Activated charcoal, given either after 5 or 30 min, significantly (p less than 0.01 or less 0.05) reduced the absorption of these 3 drugs measured, for example as AUC0-24 h. Syrup of ipecac caused emesis on each occasion, with a mean delay of 15 min. When ipecac was given 5 min after the drugs, its effect on absorption was significant, but when it was given after 30 min only the absorption of tetracycline was reduced. Activated charcoal was significantly (p less than 0.05) more effective than ipecac in reducing drug absorption when given at the same time points. In cases of acute intoxication, depending on the quality and quantity of the drugs ingested, the relative efficacy of charcoal and ipecac may be somewhat different from that observed in the present study. Despite its emetic action, however, ipecac syrup is not very effective in preventing drug absorption and, in general, activated charcoal should also be given after induced emesis or gastric lavage. PMID:6134626

  2. Superactivation of AMPA receptors by auxiliary proteins

    PubMed Central

    Carbone, Anna L.; Plested, Andrew J. R.

    2016-01-01

    Glutamate receptors form complexes in the brain with auxiliary proteins, which control their activity during fast synaptic transmission through a seemingly bewildering array of effects. Here we devise a way to isolate the activation of complexes using polyamines, which enables us to show that transmembrane AMPA receptor regulatory proteins (TARPs) exert their effects principally on the channel opening reaction. A thermodynamic argument suggests that because TARPs promote channel opening, receptor activation promotes AMPAR-TARP complexes into a superactive state with high open probability. A simple model based on this idea predicts all known effects of TARPs on AMPA receptor function. This model also predicts unexpected phenomena including massive potentiation in the absence of desensitization and supramaximal recovery that we subsequently detected in electrophysiological recordings. This transient positive feedback mechanism has implications for information processing in the brain, because it should allow activity-dependent facilitation of excitatory synaptic transmission through a postsynaptic mechanism. PMID:26744192

  3. LOX/hydrocarbon auxiliary propulsion system study

    NASA Technical Reports Server (NTRS)

    Orton, G. F.; Mark, T. D.; Weber, D. D.

    1982-01-01

    Liquid oxygen (LOX)/hydrocarbon propulsion concepts for a "second generation' orbiter auxiliary propulsion system was evaluated. The most attractive fuel and system design approach identified, and the technology advancements that are needed to provide high confidence for a subsequent system development were determined. The fuel candidates were ethanol, methane, propane, and ammonia. Even though ammonia is not a hydrocarbon, it was included for evaluation because it is clean burning and has a good technology base. The major system design options were pump versus pressure feed, cryogenic versus ambient temperature RCS propellant feed, and the degree of OMS-RCS integration. Ethanol was determined to be the best fuel candidate. It is an earth-storable fuel with a vapor pressure slightly higher than monomethyl hydrazine. A pump-fed OMS was recommended because of its high specific impulse, enabling greater velocity change and greater payload capability than a pressure fed system.

  4. Engine powered auxiliary air supply system

    SciTech Connect

    Mc Lean, J.R.

    1987-01-27

    This patent describes an auxiliary air supply system comprising: an engine; at least one exhaust driven turbocharger including a turbine and a compressor associated therewith for supply of compressed air to the engine; a low pressure compressor including means for powering the low pressure compressor utilizing the engine exhaust gas and flow connected to receive a portion of the compressed air exiting the engine turbocharger compressor; a high pressure compressor including means for powering the high pressure compressor utilizing the engine exhaust gas and flow connected to receive the compressed air exiting the low pressure compressor; and means for directing engine exhaust gases between at least one engine turbocharger and the means for powering the low and high pressure compressors.

  5. Auxiliary heating results from PDX and PLT

    SciTech Connect

    Davis, S.L.

    1982-09-01

    Auxiliary heating experiments are continuing on both PLT and PDX. PLT has increased the available ICRF power delivered to the plasma to 3 MW for the 42 MHz system and to 1.6 MW for the 25 MHz system. Deuteron and electron heating are observed in the minority /sup 3/He (T/sub d/ approx. 2.8 keV, T/sub e/ approx. 2.2 keV) and H (T/sub d/ approx. 2 keV, T/sub e/ approx. 2.5 keV) heating regimes. In addition, ion heating has been observed in the second harmonic regime (T/sub eff/ = 2/3 = 3.3 keV).

  6. What can we tell from particle morphology in Mesozoic charcoal assemblages?

    NASA Astrophysics Data System (ADS)

    Crawford, Alastair; Belcher, Claire

    2015-04-01

    Sedimentary charcoal particles provide a valuable record of palaeofire activity on both human and geological timescales. Charcoal is both an unambiguous indicator of wildfire, and a means of preservation of plant material in an inert form; thus it records not only the occurrence and extent of wildfire, but also the species affected. While scanning electron microscopy can be usefully employed for precise taxonomic identification of charcoals, the time and cost associated with this limit the extent to which the technique is employed. Morphometric analysis of mesocharcoal particles (c. 125-1000 µm) potentially provides a simple method for obtaining useful information from optical microscopy images. Grass fires have been shown to produce mesocharcoal particles with a higher length-to-width ratio than woodland fuel sources. In Holocene archives, aspect ratio measurements are thus used to infer the broad taxonomic affinity of the burned vegetation. Since Mesozoic charcoals display similarly heterogeneous morphologies, we investigate whether there is a similar potential to infer the broad botanical affinities of Mesozoic charcoal assemblages from simple morphological metrics. We have used image analysis to analyse a range of Jurassic and Cretaceous sedimentary rocks representing different vegetation communities and depositional environments, and also to determine the range of charcoal particle morphologies which can be produced from different modern taxa under laboratory conditions. We find that modern charcoals break down into mesocharcoal particles of very variable aspect ratio, and this appears to be dependent on taxonomic position. Our analysis of fragmented laboratory-produced charcoals indicates that pteridophytes produce much more elongate particles than either conifers or non-grass angiosperms. We suggest that for charcoal assemblages that predate the evolution of grasses, high average aspect ratios may be a useful indicator of the burning of a pteridophyte

  7. Charcoal emissions as a source of CO and carcinogenic PAH in mainstream narghile waterpipe smoke.

    PubMed

    Monzer, Bassel; Sepetdjian, Elizabeth; Saliba, Najat; Shihadeh, Alan

    2008-09-01

    Burning charcoal is normally placed atop the tobacco to smoke the narghile waterpipe. We investigated the importance of charcoal as a toxicant source in the mainstream smoke, with particular attention to two well-known charcoal emissions: carbon monoxide (CO) and polyaromatic hydrocarbons (PAH). CO and PAH yields were compared when a waterpipe was machine smoked using charcoal and using an electrical heating element. The electrical heating element was designed to produce spatial and temporal temperature distributions similar to those measured using charcoal. With a popular type of ma'assel tobacco mixture, and using a smoking regimen consisting of 105 puffs of 530ml volume spaced 17s apart, it was found that approximately 90% of the CO and 75-92% of the 4- and 5-membered ring PAH compounds originated in the charcoal. Greater than 95% of the benzo(a)pyrene in the smoke was attributable to the charcoal. It was also found that the relative proportions of individual PAH species, the "PAH fingerprint", of the mainstream smoke were highly correlated to those extracted from the unburned charcoal (R(2)>0.94). In contrast, there was no correlation between the PAH fingerprint of the electrically heated and charcoal-heated conditions (R(2)<0.02). In addition to inhaling toxicants transferred from the tobacco, such as nicotine, "tar", and nitrosamines, waterpipe smokers thus also inhale large quantities of combustion-generated toxicants. This explains why, despite the generally low temperatures attained in the narghile tobacco, large quantities of CO and PAH have been found in the smoke. PMID:18573302

  8. Charcoal addition to soils in NE England: a carbon sink with environmental co-benefits?

    PubMed

    Bell, M J; Worrall, F

    2011-04-01

    Interest in the application of biochar (charcoal produced during the pyrolysis of biomass) to agricultural land is increasing across the world, recognised as a potential way to capture and store atmospheric carbon. Its interest is heightened by its potential co-benefits for soil quality and fertility. The majority of research has however been undertaken in tropical rather than temperate regions. This study assessed the potential for lump-wood charcoal addition (as a substitute for biochar) to soil types which are typically under arable and forest land-use in North East England. The study was undertaken over a 28 week period and found: i) No significant difference in net ecosystem respiration (NER) between soils containing charcoal and those without, other than in week 1 of the trial. ii) A significantly higher dissolved organic carbon (DOC) flux from soils containing large amounts of charcoal than from those untreated, when planted with ryegrass. iii) That when increased respiration or DOC loss did occur, neither was sufficiently large to alter the carbon sink benefits of charcoal application. iv) That charcoal incorporation resulted in a significantly lower nitrate flux in soil leachate from mineral soils. v) That charcoal incorporation caused significant increases in soil pH, from 6.98 to 7.22 on bare arable soils when 87,500 kg charcoal/ha was applied. Consideration of both the carbon sink and environmental benefits observed here suggests that charcoal application to temperate soils typical of North East England should be considered as a method of carbon sequestration. Before large scale land application is encouraged, further large scale trials should be undertaken to confirm the positive results of this research.

  9. Comparing the Performance of Hyperbolic and Circular Rod Quadrupole Mass Spectrometers with Applied Higher Order Auxiliary Excitation

    NASA Technical Reports Server (NTRS)

    Gershman, D.J.; Block, B.P.; Rubin, M.; Benna, M.; Mahaffy, P. R.; Zurbuchen, T. H.

    2012-01-01

    This work applies higher order auxiliary excitation techniques to two types of quadrupole mass spectrometers (QMSs): commercial systems and spaceborne instruments. The operational settings of a circular rod geometry commercial system and an engineering test-bed for a hyperbolic rod geometry spaceborne instrument were matched, with the relative performance of each sensor characterized with and without applied excitation using isotopic measurements of Kr+. Each instrument was operated at the limit of the test electronics to determine the effect of auxiliary excitation on extending instrument capabilities. For the circular rod sensor, with applied excitation, a doubling of the mass resolution at 1% of peak transmission resulted from the elimination of the low-mass side peak tail typical of such rod geometries. The mass peak stability and ion rejection efficiency were also increased by factors of 2 and 10, respectively, with voltage scan lines passing through the center of stability islands formed from auxiliary excitation. Auxiliary excitation also resulted in factors of 6 and 2 in peak stability and ion rejection efficiency, respectively, for the hyperbolic rod sensor. These results not only have significant implications for the use of circular rod quadrupoles with applied excitation as a suitable replacement for traditional hyperbolic rod sensors, but also for extending the capabilities of existing hyperbolic rod QMSs for the next generation of spaceborne instruments and low-mass commercial systems.

  10. Charcoal production in the Mopane woodlands of Mozambique: what are the trade-offs with other ecosystem services?

    PubMed

    Woollen, Emily; Ryan, Casey M; Baumert, Sophia; Vollmer, Frank; Grundy, Isla; Fisher, Janet; Fernando, Jone; Luz, Ana; Ribeiro, Natasha; Lisboa, Sá N

    2016-09-19

    African woodlands form a major part of the tropical grassy biome and support the livelihoods of millions of rural and urban people. Charcoal production in particular is a major economic activity, but its impact on other ecosystem services is little studied. To address this, our study collected biophysical and social datasets, which were combined in ecological production functions, to assess ecosystem service provision and its change under different charcoal production scenarios in Gaza Province, southern Mozambique. We found that villages with longer histories of charcoal production had experienced declines in wood suitable for charcoal, firewood and construction, and tended to have lower perceived availabilities of these services. Scenarios of future charcoal impacts indicated that firewood and woody construction services were likely to trade-off with charcoal production. However, even under the most extreme charcoal scenario, these services were not completely lost. Other provisioning services, such as wild food, medicinal plants and grass, were largely unaffected by charcoal production. To reduce the future impacts of charcoal production, producers must avoid increased intensification of charcoal extraction by avoiding the expansion of species and sizes of trees used for charcoal production. This is a major challenge to land managers and policymakers in the area.This article is part of the themed issue 'Tropical grassy biomes: linking ecology, human use and conservation'. PMID:27502380

  11. Charcoal production in the Mopane woodlands of Mozambique: what are the trade-offs with other ecosystem services?

    PubMed

    Woollen, Emily; Ryan, Casey M; Baumert, Sophia; Vollmer, Frank; Grundy, Isla; Fisher, Janet; Fernando, Jone; Luz, Ana; Ribeiro, Natasha; Lisboa, Sá N

    2016-09-19

    African woodlands form a major part of the tropical grassy biome and support the livelihoods of millions of rural and urban people. Charcoal production in particular is a major economic activity, but its impact on other ecosystem services is little studied. To address this, our study collected biophysical and social datasets, which were combined in ecological production functions, to assess ecosystem service provision and its change under different charcoal production scenarios in Gaza Province, southern Mozambique. We found that villages with longer histories of charcoal production had experienced declines in wood suitable for charcoal, firewood and construction, and tended to have lower perceived availabilities of these services. Scenarios of future charcoal impacts indicated that firewood and woody construction services were likely to trade-off with charcoal production. However, even under the most extreme charcoal scenario, these services were not completely lost. Other provisioning services, such as wild food, medicinal plants and grass, were largely unaffected by charcoal production. To reduce the future impacts of charcoal production, producers must avoid increased intensification of charcoal extraction by avoiding the expansion of species and sizes of trees used for charcoal production. This is a major challenge to land managers and policymakers in the area.This article is part of the themed issue 'Tropical grassy biomes: linking ecology, human use and conservation'.

  12. Charcoal production in the Mopane woodlands of Mozambique: what are the trade-offs with other ecosystem services?

    PubMed Central

    Baumert, Sophia; Vollmer, Frank; Grundy, Isla; Fisher, Janet; Fernando, Jone; Luz, Ana; Lisboa, Sá N.

    2016-01-01

    African woodlands form a major part of the tropical grassy biome and support the livelihoods of millions of rural and urban people. Charcoal production in particular is a major economic activity, but its impact on other ecosystem services is little studied. To address this, our study collected biophysical and social datasets, which were combined in ecological production functions, to assess ecosystem service provision and its change under different charcoal production scenarios in Gaza Province, southern Mozambique. We found that villages with longer histories of charcoal production had experienced declines in wood suitable for charcoal, firewood and construction, and tended to have lower perceived availabilities of these services. Scenarios of future charcoal impacts indicated that firewood and woody construction services were likely to trade-off with charcoal production. However, even under the most extreme charcoal scenario, these services were not completely lost. Other provisioning services, such as wild food, medicinal plants and grass, were largely unaffected by charcoal production. To reduce the future impacts of charcoal production, producers must avoid increased intensification of charcoal extraction by avoiding the expansion of species and sizes of trees used for charcoal production. This is a major challenge to land managers and policymakers in the area. This article is part of the themed issue ‘Tropical grassy biomes: linking ecology, human use and conservation’. PMID:27502380

  13. A charcoal sampling method and a gas chromatographic analytical procedure for carbon disulfide.

    PubMed

    McCammon, C S; Quinn, P M; Kupel, R E

    1975-08-01

    Research is reported concerning an acceptable method for sampling and analyzing samples for carbon disulfide. Test atmospheres of carbon disulfide were generated dynamically using the syringe injection method, ant the theoretical concetnration verified by a liquid absorbent, colorimetric method. The CS2 was adsorbed on charcoal tubes, eluted with benzene, and quantitated with a gas chromatography equipped with a sulfer flame photometric detector. The results compared with the colorimetris analysis. The sensitivity of this method is 1 mug on a charcoal tube. The charcoal tubes were also tested for breakthrough volumes, holding power vs time, and the effect of air transport and temperature cycles.

  14. Black carbon quantification in charcoal-enriched soils by differential scanning calorimetry

    NASA Astrophysics Data System (ADS)

    Hardy, Brieuc; Cornelis, Jean-Thomas; Leifeld, Jens

    2015-04-01

    Black carbon (BC), the solid residue of the incomplete combustion of biomass and fossil fuels, is ubiquitous in soil and sediments, fulfilling several environmental services such as long-term carbon storage. BC is a particularly important terrestrial carbon pool due to its large residence time compared to thermally unaltered organic matter, which is largely attributed to its aromatic structure. However, BC refers to a wide range of pyrogenic products from partly charred biomass to highly condensed soot, with a degree of aromaticity and aromatic condensation varying to a large extend across the BC continuum. As a result, BC quantification largely depends on operational definitions, with the extraction efficiency of each method varying across the entire BC range. In our study, we investigated the adequacy of differential scanning calorimetry (DSC) for the quantification of BC in charcoal-enriched soils collected in the topsoil of pre-industrial charcoal kilns in forest and cropland of Wallonia, Belgium, where charcoal residues are mixed to uncharred soil organic matter (SOM). We compared the results to the fraction of the total organic carbon (TOC) resisting to K2Cr2O7 oxidation, another simple method often used for BC measurement. In our soils, DSC clearly discriminates SOM from chars. SOM is less thermally stable than charcoal and shows a peak maximum around 295°C. In forest and agricultural charcoal-enriched soils, three peaks were attributed to the thermal degradation of BC at 395, 458 and 523°C and 367, 420 and 502 °C, respectively. In cropland, the amount of BC calculated from the DSC peaks is closely related (slope of the linear regression = 0.985, R²=0.914) to the extra organic carbon content measured at charcoal kiln sites relative to the charcoal-unaffected adjacent soils, which is a positive indicator of the suitability of DSC for charcoal quantification in soil. The first BC peak, which may correspond to highly degraded charcoal, contributes to a

  15. Ozone removal capability of a welding fume respirator containing activated charcoal

    SciTech Connect

    Johnston, A.R.; Dyrud, J.F.; Shih, Y.T. )

    1989-09-01

    Development of air purifying respirators for protection against ozone has been slowed by concerns about oxidation of charcoal and other available sorbents. The suitability of a charcoal sorbent for low concentrations of ozone was evaluated as a part of the development of a half-mask air purifying respirator designed for welding fumes and ozone. Testing of the respirator confirmed that charcoal can be a suitable sorbent for low levels of ozone. Where the respirator is properly selected, fit tested, and worn, respirator use against welding fumes and ozone at concentrations not exceeding 10 times the permissible exposure limit had been recommended.

  16. Ozone removal capability of a welding fume respirator containing activated charcoal.

    PubMed

    Johnston, A R; Dyrud, J F; Shih, Y T

    1989-09-01

    Development of air purifying respirators for protection against ozone has been slowed by concerns about oxidation of charcoal and other available sorbents. The suitability of a charcoal sorbent for low concentrations of ozone was evaluated as a part of the development of a half-mask air purifying respirator designed for welding fumes and ozone. Testing of the respirator confirmed that charcoal can be a suitable sorbent for low levels of ozone. Where the respirator is properly selected, fit tested, and worn, respirator use against welding fumes and ozone at concentrations not exceeding 10 times the permissible exposure limit had been recommended. PMID:2801512

  17. 40 CFR 1033.510 - Auxiliary power units.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If...

  18. 40 CFR 1033.510 - Auxiliary power units.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If...

  19. 40 CFR 1033.510 - Auxiliary power units.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If...

  20. 40 CFR 1033.510 - Auxiliary power units.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If...

  1. 40 CFR 1033.510 - Auxiliary power units.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If...

  2. 49 CFR 229.125 - Headlights and auxiliary lights.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Headlights and auxiliary lights. 229.125 Section... Cab Equipment § 229.125 Headlights and auxiliary lights. (a) Each lead locomotive used in road service.... (c) Headlights shall be provided with a device to dim the light. (d) Effective December 31,...

  3. 49 CFR 229.125 - Headlights and auxiliary lights.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Headlights and auxiliary lights. 229.125 Section... Cab Equipment § 229.125 Headlights and auxiliary lights. (a) Each lead locomotive used in road service.... (c) Headlights shall be provided with a device to dim the light. (d) Effective December 31,...

  4. 47 CFR 80.290 - Auxiliary receiving antenna.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 5 2011-10-01 2011-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not...

  5. 47 CFR 80.290 - Auxiliary receiving antenna.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 5 2013-10-01 2013-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not...

  6. 47 CFR 80.290 - Auxiliary receiving antenna.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not...

  7. 47 CFR 80.290 - Auxiliary receiving antenna.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 5 2012-10-01 2012-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not...

  8. 47 CFR 80.290 - Auxiliary receiving antenna.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 5 2014-10-01 2014-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not...

  9. Some equivalences between the auxiliary field method and envelope theory

    SciTech Connect

    Buisseret, Fabien; Semay, Claude; Silvestre-Brac, Bernard

    2009-03-15

    The auxiliary field method has been recently proposed as an efficient technique to compute analytical approximate solutions of eigenequations in quantum mechanics. We show that the auxiliary field method is completely equivalent to the envelope theory, which is another well-known procedure to analytically solve eigenequations, although relying on different principles a priori. This equivalence leads to a deeper understanding of both frameworks.

  10. 49 CFR 229.125 - Headlights and auxiliary lights.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Headlights and auxiliary lights. 229.125 Section... Cab Equipment § 229.125 Headlights and auxiliary lights. (a) Each lead locomotive used in road service... light is aimed parallel to the tracks. If a locomotive or locomotive consist in road service...

  11. User Evaluation of Student and Auxiliary Services, Fall 1998.

    ERIC Educational Resources Information Center

    Weglarz, Shirley

    The Fall 1998 Student/Auxiliary Services User Evaluation for Johnson County Community College (JCCC) in Kansas was expanded to include information about service learning, vending services, services not included in the biennial evaluation, and answers to questions of topical interest submitted by managers of ten student/auxiliary services. A total…

  12. 14 CFR 25.445 - Auxiliary aerodynamic surfaces.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Auxiliary aerodynamic surfaces. 25.445... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Control Surface and System Loads § 25.445 Auxiliary aerodynamic surfaces. (a) When significant, the aerodynamic influence...

  13. 7 CFR 2902.15 - Bedding, bed linens, and towels.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Bedding, bed linens, and towels. 2902.15 Section 2902... PROCUREMENT Designated Items § 2902.15 Bedding, bed linens, and towels. (a) Definition. (1) Bedding is that group of woven cloth products used as coverings on a bed. Bedding includes products such as...

  14. Effects of bagasse-charcoal addition to soil on nitrate leaching in calcaric soils

    NASA Astrophysics Data System (ADS)

    Kameyama, K.; Miyamoto, T.; Shinogi, Y.

    2009-12-01

    Nitrate leaching in soils is often an important aspect in agriculture. Nitrate is leached from the root zone, where plants can utilize them, by surplus rainfall because little nitrate is absorbed by soil colloids. Miyako Island (target area) is located in the subtropical zone and comprised of coral limestone with high permeability. Land surface is covered with calcaric dark red soil that is called “Shimajiri-Maji”. Since the soil has low water- and fertilizer-retaining capacity, fertilizer-derived nitrogen easily leaches from the root zone during surplus rainfall and the nitrogen utilization efficiency of crops is relatively low. Biochars, charcoal produced from pyrolysis of biomass, are known to adsorb dissolved nitrate. Sugarcane bagasse is the main biomass resource on the island because agriculture is the main industry on the island and sugarcane is cultivated in approximately 70% of the farmland. However, the adsorption characteristics of bagasse-charcoals for nitrate have not yet been clarified. The objective of this study was to evaluate the dependency of carbonization temperatures on the nitrate adsorption properties of bagasse-charcoals and the effects of bagasse-charcoal addition to the soil on NO3-N transport in the soil for optimal use of bagasse-charcoal as a soil amendment in Miyako Island. Sugarcane bagasse were air-dried and heated in a batch-type carbonization furnace at five different carbonization temperatures (400, 500, 600, 700 and 800°C) with a holding time of 2 h. Nitrate adsorption by soil and bagasse-charcoals at each carbonization temperature was measured by the batch equilibrium technique. NO3-N transport behavior in charcoal-amended soils (rates of charcoal addition: 0, 5 and 10 wt %) was evaluated in the column experiments. The breakthrough curves of NO3-N concentrations in the effluents from the bottom of the columns were analyzed with a convective-dispersion model. The model described one-dimensional transport of a sorbing solute

  15. Hybrid fluidized bed combuster

    DOEpatents

    Kantesaria, Prabhudas P.; Matthews, Francis T.

    1982-01-01

    A first atmospheric bubbling fluidized bed furnace is combined with a second turbulent, circulating fluidized bed furnace to produce heat efficiently from crushed solid fuel. The bed of the second furnace receives the smaller sizes of crushed solid fuel, unreacted limestone from the first bed, and elutriated solids extracted from the flu gases of the first bed. The two-stage combustion of crushed solid fuel provides a system with an efficiency greater than available with use of a single furnace of a fluidized bed.

  16. Combustion efficiency and hydrocarbon emissions from charcoal production kilns in the tropics

    SciTech Connect

    Ward, D.E.; Hao, W.M.; Babbitt, R.E.

    1995-12-01

    Charcoal is one of the major energy resources in tropical countries. We investigate the combustion processes in charcoal production kilns in Zambia and Brazil. The Zambian kilns were made of earth and there was sufficient air for combustion inside the kilns. The Brazilian kilns were made of bricks which limited the available oxygen. The combustion efficiency and the concentrations of CO{sub 2}, CO, CH{sub 4}, C{sub 2}-C{sub 6} alkanes and alkenes, and aromatic compounds produced were monitored throughout the combustion processes. The contributions of charcoal production processes to the atmospheric sources of these gases were estimated. The strategies for improving charcoal yield and reducing emissions of carbon-containing compounds are discussed.

  17. Efficacy of charcoal cathartic versus ipecac in reducing serum acetaminophen in a simulated overdose.

    PubMed

    McNamara, R M; Aaron, C K; Gemborys, M; Davidheiser, S

    1989-09-01

    The traditional role of gastric emptying as the initial step in the management of the poisoned patient has recently been questioned; immediate activated charcoal administration has been recommended by some. In the setting of acetaminophen overdose, ipecac-induced emesis may interfere with subsequent oral antidotal therapy. Therefore, we conducted a study to compare the efficacy of initial therapy with ipecac with therapy with activated charcoal-cathartic in a simulated acetaminophen overdosage. Ten healthy volunteers participated in a randomized, crossover trial. Subjects ingested 3.0 g acetaminophen, followed by either no intervention, 30 mL syrup of ipecac, or 50 g activated charcoal-sorbitol solution at one hour. Serial acetaminophen levels were determined at intervals over eight hours. Both interventions significantly reduced the area under the curve compared with control (P less than .05). When comparing ipecac with activated charcoal-cathartic, no significant difference was noted among these groups. PMID:2569851

  18. Activated charcoal-carboxymethylcellulose gel formulation as an antidotal agent for orally ingested aspirin.

    PubMed

    Mathur, L K; Jaffe, J M; Colaizzi, J L; Moriarty, R W

    1976-07-01

    The in vivo effect on aspirin absorption of a potentially more palatable form of activated charcoal was compared to that of a simple aqueous slurry of activated charcoal. The experimental formulation consisted of 20.0 g of activated charcoal, 2.25 g of carboxymethylcellulose (CMC) and 42.8 ml of water; it was tested with and without chocolate syrup as a flavoring agent added just prior to administration. Six subjects were treated in crossover fashion following an aspirin dose of 972 mg. Total urinary excretion of salicylate was measured over 48 hours. Although all three treatments appeared to be effective in reducing the rate and extent of aspirin absorption, the slurry was significantly more effective in reducing the total amount absorbed than the charcoal-CMC gel with chocolate syrup. The slight difference in effectiveness between the gel formulation with and without the chocolate syrup was not significant. PMID:941924

  19. Chemical structure of wood charcoal by infrared spectroscopy and multivariate analysis.

    PubMed

    Labbé, Nicole; Harper, David; Rials, Timothy; Elder, Thomas

    2006-05-17

    In this work, the effect of temperature on charcoal structure and chemical composition is investigated for four tree species. Wood charcoal carbonized at various temperatures is analyzed by mid infrared spectroscopy coupled with multivariate analysis and by thermogravimetric analysis to characterize the chemical composition during the carbonization process. The multivariate models of charcoal were able to distinguish between species and wood thermal treatments, revealing that the characteristics of the wood charcoal depend not only on the wood species, but also on the carbonization temperature. This work demonstrates the potential of mid infrared spectroscopy in the whiskey industry, from the identification and classification of the wood species for the mellowing process to the chemical characterization of the barrels after the toasting and charring process. PMID:19127715

  20. Measurement and calculation of the sound absorption coefficient of pine wood charcoal

    NASA Astrophysics Data System (ADS)

    Suh, Jae Gap; Baik, Kyung min; Kim, Yong Tae; Jung, Sung Soo

    2013-10-01

    Although charcoal has been widely utilized for physical therapy and as a deodorant, water purifier, etc. due to its porous features, research on its role as a sound-absorbing material is rarely found. Thus, the sound absorption coefficients of pine wood charcoal were measured using an impedance tube and were compared with the theoretical predictions in the frequency range of 500˜ 5000 Hz. The theory developed in the current study only considers the lowest possible mode propagating along the air channels of the charcoal and shows good agreements with the measurements. As the frequency is increased, the sound absorption coefficients of pine wood charcoals also increase, but are lower than those of other commonly-used sound-absorbing materials.

  1. Indirect combustion noise of auxiliary power units

    NASA Astrophysics Data System (ADS)

    Tam, Christopher K. W.; Parrish, Sarah A.; Xu, Jun; Schuster, Bill

    2013-08-01

    Recent advances in noise suppression technology have significantly reduced jet and fan noise from commercial jet engines. This leads many investigators in the aeroacoustics community to suggest that core noise could well be the next aircraft noise barrier. Core noise consists of turbine noise and combustion noise. There is direct combustion noise generated by the combustion processes, and there is indirect combustion noise generated by the passage of combustion hot spots, or entropy waves, through constrictions in an engine. The present work focuses on indirect combustion noise. Indirect combustion noise has now been found in laboratory experiments. The primary objective of this work is to investigate whether indirect combustion noise is also generated in jet and other engines. In a jet engine, there are numerous noise sources. This makes the identification of indirect combustion noise a formidable task. Here, our effort concentrates exclusively on auxiliary power units (APUs). This choice is motivated by the fact that APUs are relatively simple engines with only a few noise sources. It is, therefore, expected that the chance of success is higher. Accordingly, a theoretical model study of the generation of indirect combustion noise in an Auxiliary Power Unit (APU) is carried out. The cross-sectional areas of an APU from the combustor to the turbine exit are scaled off to form an equivalent nozzle. A principal function of a turbine in an APU is to extract mechanical energy from the flow stream through the exertion of a resistive force. Therefore, the turbine is modeled by adding a negative body force to the momentum equation. This model is used to predict the ranges of frequencies over which there is a high probability for indirect combustion noise generation. Experimental spectra of internal pressure fluctuations and far-field noise of an RE220 APU are examined to identify anomalous peaks. These peaks are possible indirection combustion noise. In the case of the

  2. Soil charcoal to assess the impacts of past human disturbances on tropical forests.

    PubMed

    Vleminckx, Jason; Morin-Rivat, Julie; Biwolé, Achille B; Daïnou, Kasso; Gillet, Jean-François; Doucet, Jean-Louis; Drouet, Thomas; Hardy, Olivier J

    2014-01-01

    The canopy of many central African forests is dominated by light-demanding tree species that do not regenerate well under themselves. The prevalence of these species might result from ancient slash-and-burn agricultural activities that created large openings, while a decline of these activities since the colonial period could explain their deficit of regeneration. To verify this hypothesis, we compared soil charcoal abundance, used as a proxy for past slash-and-burn agriculture, and tree species composition assessed on 208 rainforest 0.2 ha plots located in three areas from Southern Cameroon. Species were classified in regeneration guilds (pioneer, non-pioneer light-demanding, shade-bearer) and characterized by their wood-specific gravity, assumed to reflect light requirement. We tested the correlation between soil charcoal abundance and: (i) the relative abundance of each guild, (ii) each species and family abundance and (iii) mean wood-specific gravity. Charcoal was found in 83% of the plots, indicating frequent past forest fires. Radiocarbon dating revealed two periods of fires: "recent" charcoal were on average 300 years old (up to 860 BP, n = 16) and occurred in the uppermost 20 cm soil layer, while "ancient" charcoal were on average 1900 years old (range: 1500 to 2800 BP, n = 43, excluding one sample dated 9400 BP), and found in all soil layers. While we expected a positive correlation between the relative abundance of light-demanding species and charcoal abundance in the upper soil layer, overall there was no evidence that the current heterogeneity in tree species composition can be explained by charcoal abundance in any soil layer. The absence of signal supporting our hypothesis might result from (i) a relatively uniform impact of past slash-and-burn activities, (ii) pedoturbation processes bringing ancient charcoal to the upper soil layer, blurring the signal of centuries-old Human disturbances, or (iii) the prevalence of other environmental

  3. Adsorption of dimethyl sulfide from aqueous solution by a cost-effective bamboo charcoal.

    PubMed

    Wang, Ming; Huang, Zheng-Hong; Liu, Guangjia; Kang, Feiyu

    2011-06-15

    The adsorption of dimethyl sulfide from an aqueous solution by a cost-effective bamboo charcoal from Dendrocalamus was studied in comparison with other carbon adsorbents. The bamboo charcoal exhibited superior adsorption on dimethyl sulfide compared with powdered activated carbons at different adsorbent dosages. The adsorption characteristics of dimethyl sulfide onto bamboo charcoal were investigated under varying experimental conditions such as particle size, contact time, initial concentration and adsorbent dosage. The dimethyl sulfide removal was enhanced from 31 to 63% as the particle size was decreased from 24-40 to >300 mesh for the bamboo charcoal. The removal efficiency increased with increasing the adsorbent dosage from 0.5 to 10mg, and reached 70% removal efficiency at 10mg adsorbed. The adsorption capacity (μg/g) increased with increasing concentration of dimethyl sulfide while the removal efficiency decreased. The adsorption process conforms well to a pseudo-second-order kinetics model. The adsorption of dimethyl sulfide is more appropriately described by the Freundlich isotherm (R(2), 0.9926) than by the Langmuir isotherm (R(2), 0.8685). Bamboo charcoal was characterized by various analytical methods to understand the adsorption mechanism. Bamboo charcoal is abundant in acidic and alcohol functional groups normally not observed in PAC. A distinct difference is that the superior mineral composition of Fe (0.4 wt%) and Mn (0.6 wt%) was detected in bamboo charcoal-elements not found in PAC. Acidic functional group and specific adsorption sites would be responsible for the strong adsorption of dimethyl sulfide onto bamboo charcoal of Dendrocalamus origin.

  4. Salts of the iodine oxyacids in the impregnation of adsorbent charcoal for trapping radioactive methyliodide

    DOEpatents

    Deitz, Victor R.; Blachly, Charles H.

    1977-04-05

    Radioactive iodine and radioactive methyliodide can be more than 99.7 per cent removed from the air stream of a nuclear reactor by passing the air stream through a 2-inch thick filter which is made up of impregnated charcoal prepared by contacting the charcoal with a solution containing KOH, iodine or an iodide, and an oxyacid, followed by contacting with a solution containing a tertiary amine.

  5. Adsorption of dimethyl sulfide from aqueous solution by a cost-effective bamboo charcoal.

    PubMed

    Wang, Ming; Huang, Zheng-Hong; Liu, Guangjia; Kang, Feiyu

    2011-06-15

    The adsorption of dimethyl sulfide from an aqueous solution by a cost-effective bamboo charcoal from Dendrocalamus was studied in comparison with other carbon adsorbents. The bamboo charcoal exhibited superior adsorption on dimethyl sulfide compared with powdered activated carbons at different adsorbent dosages. The adsorption characteristics of dimethyl sulfide onto bamboo charcoal were investigated under varying experimental conditions such as particle size, contact time, initial concentration and adsorbent dosage. The dimethyl sulfide removal was enhanced from 31 to 63% as the particle size was decreased from 24-40 to >300 mesh for the bamboo charcoal. The removal efficiency increased with increasing the adsorbent dosage from 0.5 to 10mg, and reached 70% removal efficiency at 10mg adsorbed. The adsorption capacity (μg/g) increased with increasing concentration of dimethyl sulfide while the removal efficiency decreased. The adsorption process conforms well to a pseudo-second-order kinetics model. The adsorption of dimethyl sulfide is more appropriately described by the Freundlich isotherm (R(2), 0.9926) than by the Langmuir isotherm (R(2), 0.8685). Bamboo charcoal was characterized by various analytical methods to understand the adsorption mechanism. Bamboo charcoal is abundant in acidic and alcohol functional groups normally not observed in PAC. A distinct difference is that the superior mineral composition of Fe (0.4 wt%) and Mn (0.6 wt%) was detected in bamboo charcoal-elements not found in PAC. Acidic functional group and specific adsorption sites would be responsible for the strong adsorption of dimethyl sulfide onto bamboo charcoal of Dendrocalamus origin. PMID:21549503

  6. Emissions of greenhouse gases and other airborne pollutants from charcoal making in Kenya and Brazil

    NASA Astrophysics Data System (ADS)

    Pennise, David M.; Smith, Kirk R.; Kithinji, Jacob P.; Rezende, Maria Emilia; Raad, Tulio Jardim; Zhang, Junfeng; Fan, Chengwei

    2001-10-01

    Airborne emissions from charcoal-making kilns commonly used in Kenya and Brazil were measured during typical operating conditions. Emission factors were determined for carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), carbon monoxide (CO), total nonmethane hydrocarbons, nitrogen oxides (NOx) and total suspended particulates (TSP) along with charcoal production efficiency and charcoal and fuelwood carbon and energy contents. The conversion of wood carbon to charcoal carbon ranged from 37 to 69%, depending on kiln type. Emission factors, expressed as grams of pollutant per kilogram of charcoal produced, for the eight kilns ranged from 543 to 3027 for CO2, 32-62 for CH4, 143-373 for CO, 24-124 for total nonmethane organic compounds, 0.011-0.30 for N2O, 0.0054-0.13 for NOx, and 13-41 for TSP. On average, fuelwood carbon was approximately diverted as follows: 51% to charcoal, 27% to CO2, and 13% to products of incomplete combustion (PIC). Due to the higher global warming potentials (GWPs) of PIC relative to CO2 on a carbon atom basis, such kilns can produce rather large net greenhouse gas emissions, even when the wood is harvested renewably. Based on published GWPs for CO2, CH4, and N2O only, we estimate that 0.77-1.63 kg C-CO2 (carbon as carbon dioxide equivalents) is emitted per kilogram of charcoal produced. We estimate that the total primary global warming commitment (GWC) of Kenyan and Brazilian charcoal-making kiln emissions is about 2.7 and 7.5 million tons (Mt) C-CO2, respectively. For comparison, the primary GWC from fossil fuel use in the United States is almost 1700 Mt C-CO2.

  7. Soil charcoal to assess the impacts of past human disturbances on tropical forests.

    PubMed

    Vleminckx, Jason; Morin-Rivat, Julie; Biwolé, Achille B; Daïnou, Kasso; Gillet, Jean-François; Doucet, Jean-Louis; Drouet, Thomas; Hardy, Olivier J

    2014-01-01

    The canopy of many central African forests is dominated by light-demanding tree species that do not regenerate well under themselves. The prevalence of these species might result from ancient slash-and-burn agricultural activities that created large openings, while a decline of these activities since the colonial period could explain their deficit of regeneration. To verify this hypothesis, we compared soil charcoal abundance, used as a proxy for past slash-and-burn agriculture, and tree species composition assessed on 208 rainforest 0.2 ha plots located in three areas from Southern Cameroon. Species were classified in regeneration guilds (pioneer, non-pioneer light-demanding, shade-bearer) and characterized by their wood-specific gravity, assumed to reflect light requirement. We tested the correlation between soil charcoal abundance and: (i) the relative abundance of each guild, (ii) each species and family abundance and (iii) mean wood-specific gravity. Charcoal was found in 83% of the plots, indicating frequent past forest fires. Radiocarbon dating revealed two periods of fires: "recent" charcoal were on average 300 years old (up to 860 BP, n = 16) and occurred in the uppermost 20 cm soil layer, while "ancient" charcoal were on average 1900 years old (range: 1500 to 2800 BP, n = 43, excluding one sample dated 9400 BP), and found in all soil layers. While we expected a positive correlation between the relative abundance of light-demanding species and charcoal abundance in the upper soil layer, overall there was no evidence that the current heterogeneity in tree species composition can be explained by charcoal abundance in any soil layer. The absence of signal supporting our hypothesis might result from (i) a relatively uniform impact of past slash-and-burn activities, (ii) pedoturbation processes bringing ancient charcoal to the upper soil layer, blurring the signal of centuries-old Human disturbances, or (iii) the prevalence of other environmental

  8. Should we do early and frequent charcoal hemoperfusion in phenytoin toxicity?

    PubMed Central

    Sahoo, Jyoti Narayan; Gurjar, Mohan

    2016-01-01

    Phenytoin toxicity or adverse drug reaction is common due to its narrow therapeutic window. Mild and moderate toxicity require supportive care and enteral activated charcoal. In severe toxicity, charcoal hemoperfusion (CHP) have been shown to decrease serum phenytoin half-life and early recovery. Here, we report two cases with phenytoin toxicity who showed marked clinical improvement after early and frequent CHP treatment. PMID:27076716

  9. Practice Hospital Bed Safety

    MedlinePlus

    ... Bed? Todd says that there is no standard definition for hospital beds, a fact that consumers shopping ... in retail stores that don’t meet the definition of medical devices under the law, but which ...

  10. Enuresis (Bed-Wetting)

    MedlinePlus

    ... their development. Bed-wetting is more common among boys than girls. What causes bed-wetting? A number of things ... valves in boys or in the ureter in girls or boys Abnormalities in the spinal cord A small bladder ...

  11. Experience with improved charcoal and wood stoves for households and institutions in Kenya

    SciTech Connect

    Hyman, E.L.

    1985-01-01

    Efforts at promoting more fuel-efficient charcoal stoves to replace traditional charcoal stoves in Kenya offer some lessons for the dissemination of appropriate technologies. This paper looks at the market-based approach which has made the Kenyan charcoal stoves project a success. Trends in woodfuels (wood and charcoal) consumption in Kenya are identified; the traditional technology for charcoal combustion and the upgraded traditional technologies are described; production achievement and the dissemination and promotion strategy used are examined; and a financial and economic analysis is performed with social, health and environmental effects assessed. Other ways to achieve a more favourable balance between woodfuels consumption and supply are then discussed looking at more efficient charcoal kilns and household woodstoves, improved institutional stoves and increased wood production. The replication potential of the Kenya experiment in other countries is also explored. The lessons learnt from the the Kenya experience concern the relationship between technology, choice and delivery systems as they interact with, economic, institutional, and policy factors. In this case, the design work accepted the traditional technology as a starting point which helped ensure widespread acceptance by households. The potential desirability of relying on local artisans to manufacture consumer durables using existing private sector channels to market these goods is also shown. It also highlights the importance of going beyond a laissez-faire approach and supporting training, demonstration, and publicity to faciliate the workings of the private sector. In the Kenyan case, technology choice was relatively unsubsidized and left ot the preferences of consumers.

  12. Estimation of emissions from charcoal lighter fluid and review of alternatives. Final report

    SciTech Connect

    Campbell, D.L.; Stockton, M.B.

    1990-01-01

    The report gives results of an evaluation of emissions of volatile organic compounds (VOCs) from charcoal lighter fluid, a consumer product consisting entirely of volatile constituents. An estimated 46,250 tons (42,000 Mg) of charcoal lighter fluid is used in the U.S. each year. VOCs contribute to the formation of ozone; therefore, the ozone nonattainment issue has focused attention on VOCs emitted from many sources. VOCs are emitted when charcoal lighter fluid is used, but these emissions are difficult to quantify. Evaporative VOC losses occur from the lighter fluid prior to ignition, and combustion VOC losses occur from burning lighter-fluid-soaked charcoal briquettes. This study evaluates tests conducted to date on charcoal lighter fluid emissions. The information is most complete for evaporative VOC losses. The estimates vary greatly, however, based on the length of time between application of the lighter fluid and ignition. The limited tests conducted to date have not distinguished lighter fluid from charcoal-briquette combustion emissions.

  13. Chemical and Isotopic Thresholds in Charring: Implications for the Interpretation of Charcoal Mass and Isotopic Data.

    PubMed

    Pyle, Lacey A; Hockaday, William C; Boutton, Thomas; Zygourakis, Kyriacos; Kinney, Timothy J; Masiello, Caroline A

    2015-12-15

    Charcoal plays a significant role in the long-term carbon cycle, and its use as a soil amendment is promoted as a C sequestration strategy (biochar). One challenge in this research area is understanding the heterogeneity of charcoal properties. Although the maximum reaction temperature is often used as a gauge of pyrolysis conditions, pyrolysis duration also changes charcoal physicochemical qualities. Here, we introduce a formal definition of charring intensity (CI) to more accurately characterize pyrolysis, and we document variation in charcoal chemical properties with variation in CI. We find two types of responses to CI: either linear or threshold relationships. Mass yield decreases linearly with CI, while a threshold exists across which % C, % N, and δ(15)N exhibit large changes. This CI threshold co-occurs with an increase in charcoal aromaticity. C isotopes do not change from original biomass values, supporting the use of charcoal δ(13)C signatures to infer paleoecological conditions. Fractionation of N isotopes indicates that fire may be enriching soils in (15)N through pyrolytic N isotope fractionation. This influx of "black N" could have a significant impact on soil N isotopes, which we show theoretically using a simple mass-balance model.

  14. Chemical and Isotopic Thresholds in Charring: Implications for the Interpretation of Charcoal Mass and Isotopic Data.

    PubMed

    Pyle, Lacey A; Hockaday, William C; Boutton, Thomas; Zygourakis, Kyriacos; Kinney, Timothy J; Masiello, Caroline A

    2015-12-15

    Charcoal plays a significant role in the long-term carbon cycle, and its use as a soil amendment is promoted as a C sequestration strategy (biochar). One challenge in this research area is understanding the heterogeneity of charcoal properties. Although the maximum reaction temperature is often used as a gauge of pyrolysis conditions, pyrolysis duration also changes charcoal physicochemical qualities. Here, we introduce a formal definition of charring intensity (CI) to more accurately characterize pyrolysis, and we document variation in charcoal chemical properties with variation in CI. We find two types of responses to CI: either linear or threshold relationships. Mass yield decreases linearly with CI, while a threshold exists across which % C, % N, and δ(15)N exhibit large changes. This CI threshold co-occurs with an increase in charcoal aromaticity. C isotopes do not change from original biomass values, supporting the use of charcoal δ(13)C signatures to infer paleoecological conditions. Fractionation of N isotopes indicates that fire may be enriching soils in (15)N through pyrolytic N isotope fractionation. This influx of "black N" could have a significant impact on soil N isotopes, which we show theoretically using a simple mass-balance model. PMID:26523420

  15. Applied Technology of Bamboo Charcoal to Improvement and Purification of Air Quality

    NASA Astrophysics Data System (ADS)

    Takimoto, Akira; Tada, Yukio; Onishi, Hajime; Fukazawa, Tomohiro

    The use of bamboo charcoal, which is one of the carbon from wood, attracts attention from the viewpoint of the environmental protection. Bamboo charcoal has high adsorption removal ability to various substances. In addition Bamboo charcoal is effective also for the filtration of the suspended solid and the bacterium by the macro pore that originates in the plant frame structure. In present paper, a new concept of gas clean technology by bamboo charcoal and TiO2 with UV light irradiation was proposed. Its system is composed of TiO2-coated bamboo charcoal, TiO2-coated silica gel and UV lamp. Water vapor is adsorbed by bamboo charcoal and fine particles and airborne bacterium are trapped on the surface of it. Trapped contaminant is degraded by TiO2 and UV light. In addition, the degradation is promoted by •OH produced by adsorbed water vapor. The air purification sanitization possibility in high efficiency for this system was clarified.

  16. A contribution to the identification of charcoal origin in Brazil II - Macroscopic characterization of Cerrado species.

    PubMed

    Gonçalves, Thaís A P; Nisgoski, Silvana; Oliveira, Julia S; Marcati, Carmen R; Ballarin, Adriano W; Muñiz, Graciela I B

    2016-05-13

    The Brazilian Cerrado is the richest savanna in the world. It is also one of the biomes more threatened in the country and a hotspot for conservation priorities. The main causes of deforestation in Cerrado are agricultural practices, livestock and charcoal production. Although charcoal has a minor impact, its consumption represents the deforestation of 16.000 Km² of the Cerrado. To contribute for the biomes's conservation it is very important to improve forestry supervision. Thus, in this work we present the macroscopic characterization of charcoal from 25 Cerrado's species. We simulate the real conditions of forest controllers by using the magnifications of 10x, 25x and 65x. Likewise, the charcoals micrographs are all of transverse sections due to the larger amount of anatomical information. We also analyzed texture, brightness, vitrification, ruptures and some special features. The species present several differences in their anatomical structure. Although some of them are very unique, this work does not intent to identify charcoals only by macroscopic analyses. But it might give directions to future identification of genera or species. It also provides knowledge for government agents to verify the documents of forestry origin by fast analyzing a sample of charcoal itself. PMID:27192198

  17. Making a Bed

    ERIC Educational Resources Information Center

    Wexler, Anthony; Stein, Sherman

    2005-01-01

    The origins of this paper lay in making beds by putting pieces of plywood on a frame: If beds need to be 4 feet 6 inches by 6 feet 3 inches, and plywood comes in 4-foot by 8-foot sheets, how should one cut the plywood to minimize waste (and have stable beds)? The problem is of course generalized.

  18. Space station auxiliary thrust chamber technology

    NASA Technical Reports Server (NTRS)

    Senneff, J. M.

    1986-01-01

    A program to design, fabricate and test a 50 lb sub f (222 N) thruster was undertaken (Contract NAS 3-24656) to demonstrate the applicability of the reverse flow concept as an item of auxiliary propulsion for the space station. The thruster was to operate at a mixture ratio (O/F) of 4, be capable of operating for 2 million lb sub f- seconds (8.896 million N-seconds) impulse with a chamber pressure of 75 psia (52 N/square cm) and a nozzle area ratio of 40. Superimposed was also the objective of operating with a strainless steel spherical combustion chamber, which limited the wall temperature to 1700 F (1200 K), an objective specific impulse of 400 lb sub f sec/lbm (3923 N-seconds/Kg), and a demonstration of 500,000 lb sub f-seconds (2,224,000 N-seconds) of impulse. The demonstration of these objectives required a number of design iterations which eventually culminated in a very successful 1000 second demonstration, almost immediately followed by a changed program objective imposed to redesign and demonstrate at a mixture ratio (O/F) of 8. This change was made and more then 250,000 lb sub f seconds (1,112,000 N-seconds) of impulse was successfully demonstrated at a mixture ratio of 8. This document contains a description of the effort conducted during the program to design and demonstrate the thrusters involved.

  19. Orbiter Auxiliary Power Unit Flight Support Plan

    NASA Technical Reports Server (NTRS)

    Guirl, Robert; Munroe, James; Scott, Walter

    1990-01-01

    This paper discussed the development of an integrated Orbiter Auxiliary Power Unit (APU) and Improved APU (IAPU) Flight Suuport Plan. The plan identifies hardware requirements for continued support of flight activities for the Space Shuttle Orbiter fleet. Each Orbiter vehicle has three APUs that provide power to the hydraulic system for flight control surface actuation, engine gimbaling, landing gear deployment, braking, and steering. The APUs contain hardware that has been found over the course of development and flight history to have operating time and on-vehicle exposure time limits. These APUs will be replaced by IAPUs with enhanced operating lives on a vehicle-by-vehicle basis during scheduled Orbiter modification periods. This Flight Support Plan is used by program management, engineering, logistics, contracts, and procurement groups to establish optimum use of available hardware and replacement quantities and delivery requirements for APUs until vehicle modifications and incorporation of IAPUs. Changes to the flight manifest and program delays are evaluated relative to their impact on hardware availability.

  20. Mixed Oxide Fresh Fuel Package Auxiliary Equipment

    SciTech Connect

    Yapuncich, F.; Ross, A.; Clark, R.H.; Ammerman, D.

    2008-07-01

    The United States Department of Energy's National Nuclear Security Administration (NNSA) is overseeing the construction the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF) on the Savannah River Site. The new facility, being constructed by NNSA's contractor Shaw AREVA MOX Services, will fabricate fuel assemblies utilizing surplus plutonium as feedstock. The fuel will be used in designated commercial nuclear reactors. The MOX Fresh Fuel Package (MFFP), which has recently been licensed by the Nuclear Regulatory Commission (NRC) as a type B package (USA/9295/B(U)F-96), will be utilized to transport the fabricated fuel assemblies from the MFFF to the nuclear reactors. It was necessary to develop auxiliary equipment that would be able to efficiently handle the high precision fuel assemblies. Also, the physical constraints of the MFFF and the nuclear power plants require that the equipment be capable of loading and unloading the fuel assemblies both vertically and horizontally. The ability to reconfigure the load/unload evolution builds in a large degree of flexibility for the MFFP for the handling of many types of both fuel and non fuel payloads. The design and analysis met various technical specifications including dynamic and static seismic criteria. The fabrication was completed by three major fabrication facilities within the United States. The testing was conducted by Sandia National Laboratories. The unique design specifications and successful testing sequences will be discussed. (authors)

  1. Confinement Studies of Auxiliary Heated NSTX Plasmas

    SciTech Connect

    B.P. LeBlanc; M.G. Bell; R.E. Bell; M.L. Bitter; C. Bourdelle; D.A. Gates; S.M. Kaye; R. Maingi; J.E. Menard; D. Mueller; S.F. Paul; A.L. Roquemore; A. Rosenberg1; S.A. Sabbagh; D. Stutman; E.J. Synakowski; V.A. Soukhanovskii; J.R.Wilson; the NSTX Research Team

    2003-05-06

    The confinement of auxiliary heated NSTX discharges is discussed. The energy confinement time in plasmas with either L-mode or H-mode edges is enhanced over the values given by the ITER97L and ITER98Pby(2) scalings, being up to 2-3 times L-mode and 1.5 times H-mode. TRANSP calculations based on the kinetic profile measurements reproduce the magnetics-based determination of stored energy and the measured neutron production rate. Power balance calculations reveal that, in a high power neutral beam heated H-mode discharge, the ion thermal transport is near neoclassical levels, and well below the electron thermal transport, which is the main loss channel. Perturbative impurity injection techniques indicate the particle diffusivity to be slightly above the neoclassical level in discharges with L-mode edge. High-harmonic fast-wave (HHFW) bulk electron heating is described and thermal transport is discussed. Thermal ion transport is found to be above neoclassical level, but thermal electron transport remains the main loss mechanism. Evidences of an electron thermal internal transport barrier obtained with HHFW heating are presented. A description of H-mode discharges obtained during HHFW heating is presented.

  2. Space Station auxiliary thrust chamber technology

    NASA Technical Reports Server (NTRS)

    Robinson, Philip J.

    1990-01-01

    The objective was to establish a technical data base to support future development of GO2/GH2 flight thrusters for a Space Station Auxiliary Propulsion System. Specific issues of concern were thruster performance and cycle life. To address these issues, NASA funded Aerojet to design, fabricate, and altitude test two 25-lbf GO2/GH2 thrusters. The first thruster was designed to operate at a nominal mixture ratio (O/F) of 4.0 and expansion area ratio (epsilon) of 100:1. It was tested over a range of O/F from 2.0 to 8.0, achieving a range of specific impulse (Isp) from 440 to 310 lbf-sec/Ibm. The second thruster was optimized for a nominal O/F of 8.0 at a lower nozzle expansion area ratio, epsilon, of 30:1. This second thruster was tested over an O/F range of 3.0 to 9.5, achieving an Isp range of 416 to 3323 lbf-sec/Ibm, respectively. At O/F = 8.0, the Isp was 360 lbf-sec/Ibm, as predicted.

  3. Phanerozoic concentrations of atmospheric oxygen reconstructed from sedimentary charcoal

    NASA Astrophysics Data System (ADS)

    Glasspool, Ian J.; Scott, Andrew C.

    2010-09-01

    Variations of the Earth's atmospheric oxygen concentration (pO2) are thought to be closely tied to the evolution of life, with strong feedbacks between uni- and multicellular life and oxygen. On the geologic timescale, pO2 is regulated by the burial of organic carbon and sulphur, as well as by weathering. Reconstructions of atmospheric O2 for the past 400million years have therefore been based on geochemical models of carbon and sulphur cycling. However, these reconstructions vary widely, particularly for the Mesozoic and early Cenozoic eras. Here we show that the abundance of charcoal in mire settings is controlled by pO2, and use this proxy to reconstruct the concentration of atmospheric oxygen for the past 400million years. We estimate that pO2 was continuously above 26% during the Carboniferous and Permian periods, and that it declined abruptly around the time of the Permian-Triassic mass extinction. During the Triassic and Jurassic periods, pO2 fluctuated cyclically, with amplitudes up to 10% and a frequency of 20-30million years. Atmospheric oxygen concentrations have declined steadily from the middle of the Cretaceous period to present-day values of about 21%. We conclude, however, that variation in pO2 was not the main driver of the loss of faunal diversity during the Permo-Triassic and Triassic-Jurassic mass extinction events.

  4. Auxiliary signal processing system for a multiparameter radar

    NASA Technical Reports Server (NTRS)

    Chandrasekar, V.; Gray, G. R.; Caylor, I. J.

    1993-01-01

    The design of an auxiliary signal processor for a multiparameter radar is described with emphasis on low cost, quick development, and minimum disruption of radar operations. The processor is based around a low-cost digital signal processor card and personal computer controller. With the use of such a concept, an auxiliary processor was implemented for the NCAR CP-2 radar during a 1991 summer field campaign and allowed measurement of additional polarimetric parameters, namely, the differential phase and the copolar cross correlation. Sample data are presented from both the auxiliary and existing radar signal processors.

  5. Solar powered actuator with continuously variable auxiliary power control

    NASA Technical Reports Server (NTRS)

    Nola, F. J. (Inventor)

    1984-01-01

    A solar powered system is disclosed in which a load such as a compressor is driven by a main induction motor powered by a solar array. An auxiliary motor shares the load with the solar powered motor in proportion to the amount of sunlight available, is provided with a power factor controller for controlling voltage applied to the auxiliary motor in accordance with the loading on that motor. In one embodiment, when sufficient power is available from the solar cell, the auxiliary motor is driven as a generator by excess power from the main motor so as to return electrical energy to the power company utility lines.

  6. Getting Rid of Bed Bugs

    MedlinePlus

    ... Bed Bugs — Do-it-yourself Bed Bug Control — Pesticides to Control Bed Bugs Bed Bug Information Clearinghouse ... Greener Living Health and Safety Land and Cleanup Pesticides Waste Water Science & Technology Air Climate Change Ecosystems ...

  7. Chemical changes in soil charcoal of differing ages inferred from DRIFT spectra

    NASA Astrophysics Data System (ADS)

    Hobley, E. U.; Willgoose, G. R.; Frisia, S.; Jacobsen, G.

    2012-04-01

    Visible charcoal fragments were manually isolated from a sandy soil from the Southern Highlands of NSW, Australia, at depths of 0 - 30 cm and 30 - 60 cm. In the topsoil, the charcoal had a radiocarbon age of 85 ± 35 years BP, whereas the charcoal from the 30 - 60 cm layer was radiocarbon dated at 2540 ± 35 years BP. Diffuse reflectance FTIR (DRIFT) spectra of the charcoal reveal differences in both the number of peaks detected and their magnitudes. In the IR region 750 - 3800 cm-1, the charcoal from the lower depth had less peaks (140) than that of the topsoil (217). In the 1400 - 1600 cm-1 region, generally attributed to aromatics, the peaks were larger and more numerous (22 peaks) in the 0 - 30 cm sample than those of the 30 - 60 cm depth (14 peaks). The C-H stretch of alkenes and aromatics (3000 - 3100 cm-1) was similar at both depths, but the peak generally associated with the C-H stretch of alkanes (methyl and methylene groups) at 2850 - 3000 cm-1 was smaller in 30 - 60 cm depth than in the topsoil. In contrast to the reduction in aromatic and alkane signatures, oxidised forms were more pronounced in the older, deeper charcoal. Peaks associated with the free hydroxyl O-H stretch (alcohols and phenols) at 3640 - 3610 cm-1, carboxylic acids (910 - 950 cm-1), aliphatic O-H (alcohols) (1050 - 1150 cm-1) and cellulose-like structures (1020 cm-1), which contain a large number of uncondensed, oxidised rings, were larger in the charcoal from 30 - 60 cm than in that from the topsoil. Our results confirm that charcoal is highly persistent in soils, being retained for millennia. Aromatic structures are present in both younger and older charcoal, but decay leads to a reduction in the number and area of peaks detected at 1400 - 1600 cm-1, indicating less aromaticity. Alkane C-H also decreases with aging, probably attributable to its preferential degradation by soil microbes compared with condensed aromatic structures. Concurrent with diminished aromatic and alkane

  8. 44. AUXILIARY CHAMBER BETWEEN CHAMBER AND CONCRETE ENCLOSURE (LOCATION CCC), ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    44. AUXILIARY CHAMBER BETWEEN CHAMBER AND CONCRETE ENCLOSURE (LOCATION CCC), LOOKING NORTHEAST SHOWING DRAIN PIPE FROM SUMP - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  9. 41. AUXILIARY CHAMBER, CONCRETE ENCLOSURE CHAMBER AIR LOCK (EXTERIOR), LOOKING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    41. AUXILIARY CHAMBER, CONCRETE ENCLOSURE CHAMBER AIR LOCK (EXTERIOR), LOOKING NORTHEAST FROM SOUTHWEST CORNER (LOCATION AAA) - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  10. 48. AUXILIARY CHAMBER (EAST END), VIEW LOOKING EAST SHOWING ELECTRICAL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    48. AUXILIARY CHAMBER (EAST END), VIEW LOOKING EAST SHOWING ELECTRICAL PENETRATION AND AIR LOCK (LOCATION GGG) - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  11. 45. AUXILIARY CHAMBER BETWEEN CHAMBER AND CONCRETE ENCLOSURE (LOCATION DDD), ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    45. AUXILIARY CHAMBER BETWEEN CHAMBER AND CONCRETE ENCLOSURE (LOCATION DDD), VIEW LOOKING EAST. LEAD ENCLOSED PIPING IS DRAIN FROM BOILER CHAMBER No. 1 - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  12. 46. AUXILIARY CHAMBER (EAST END), LOOKING NORTHWEST AT STEAM AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    46. AUXILIARY CHAMBER (EAST END), LOOKING NORTHWEST AT STEAM AND FEEDWATER PIPING AND PRESSURIZER AND FLASH/BLOWOFF TANK ROOMS (LOCATION EEE) - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  13. The Solid Rocket Booster Auxiliary Power Unit: Meeting the Challenge

    NASA Technical Reports Server (NTRS)

    Hughes, R. W.

    1985-01-01

    The thrust vector control systems of the solid rocket boosters are turbine-powered, electrically controlled hydraulic systems which function through hydraulic actuators to gimbal the nozzles of the solid rocket boosters and provide vehicle steering for the Space Shuttle. Turbine power for the thrust vector control systems is provided through hydrazine fueled auxiliary power units which drive the hydraulic pumps. The solid rocket booster auxiliary power unit resulted from trade studies which indicated significant advantages would result if an existing engine could be found to meet the program goal of 20 missions reusability and adapted to meet the seawater environments associated with ocean landings. During its maturation, the auxiliary power unit underwent many design iterations and provided its flight worthiness through full qualification programs both as a component and as part of the thrust vector control system. More significant, the auxiliary power unit has successfully completed six Shuttle missions.

  14. Interior room within eastern lift span, showing auxiliary electric and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Interior room within eastern lift span, showing auxiliary electric and gas generators. - Arlington Memorial Bridge, Spanning Potomac River between Lincoln Memorial & Arlington National Cemetery, Washington, District of Columbia, DC

  15. Auxiliary Illumination For Viewing Along A Welding Torch

    NASA Technical Reports Server (NTRS)

    Gilbert, Jeffrey L.; Gutow, David A.

    1993-01-01

    Auxiliary optical subsystem provides additional illumination for through-torch vision system of type used in automated or semiautomated arc welding. Also useful during operation of torch to view parts in shadows cast by arc light.

  16. 56. LOCK AND DAM NO. 26 (REPLACEMENT). AUXILIARY LOCK AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    56. LOCK AND DAM NO. 26 (REPLACEMENT). AUXILIARY LOCK AND REMAINDER OF DAM -- CONCRETE MONOLITH PLAN AND WALL ELEVATIONS (WITH LOCK APPURTENANCES). Drawing V-601 - Upper Mississippi River 9-Foot Channel Project, Lock & Dam 26R, Alton, Madison County, IL

  17. 16. DETAIL VIEW OF AUXILIARY LOCK MITER GATE OPERATING MACHINERY ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. DETAIL VIEW OF AUXILIARY LOCK MITER GATE OPERATING MACHINERY LOCATED IN INTERMEDIATE WALL, LOOKING NORTHWEST - Upper Mississippi River 9-Foot Channel Project, Lock & Dam 27, Granite City, Madison County, IL

  18. 72. VISITOR'S CENTER, MODEL OF BOILER CHAMBER, AUXILIARY CHAMBER, REACTOR ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    72. VISITOR'S CENTER, MODEL OF BOILER CHAMBER, AUXILIARY CHAMBER, REACTOR AND CANAL (LOCATION T) - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  19. 37. VIEW OF AUXILIARY LOCK MITER GATE, WITH MAIN LOCK ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    37. VIEW OF AUXILIARY LOCK MITER GATE, WITH MAIN LOCK UPSTREAM MITER GATE AND UPSTREAM GUIDE WALL IN BACKGROUND, LOOKING NORTHEAST - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 4, Alma, Buffalo County, WI

  20. Space shuttle auxiliary power unit study, phase 2

    NASA Technical Reports Server (NTRS)

    Binsley, R. L.; Krause, A. A.; Maddox, R. D.; Marcy, R. D.; Siegler, R. S.

    1972-01-01

    A study was performed to establish the preliminary design of the space shuttle auxiliary power unit. Details of the analysis, optimizations, and design of the components, subsystems and systems are presented.

  1. Parallel Auxiliary Space AMG Solver for $H(div)$ Problems

    SciTech Connect

    Kolev, Tzanio V.; Vassilevski, Panayot S.

    2012-12-18

    We present a family of scalable preconditioners for matrices arising in the discretization of $H(div)$ problems using the lowest order Raviart--Thomas finite elements. Our approach belongs to the class of “auxiliary space''--based methods and requires only the finite element stiffness matrix plus some minimal additional discretization information about the topology and orientation of mesh entities. Also, we provide a detailed algebraic description of the theory, parallel implementation, and different variants of this parallel auxiliary space divergence solver (ADS) and discuss its relations to the Hiptmair--Xu (HX) auxiliary space decomposition of $H(div)$ [SIAM J. Numer. Anal., 45 (2007), pp. 2483--2509] and to the auxiliary space Maxwell solver AMS [J. Comput. Math., 27 (2009), pp. 604--623]. Finally, an extensive set of numerical experiments demonstrates the robustness and scalability of our implementation on large-scale $H(div)$ problems with large jumps in the material coefficients.

  2. MAN B&W`s latest HFO marine auxiliary engine

    SciTech Connect

    Kunberger, K.

    1996-09-01

    The ability to operate marine auxiliary generator sets on heavy fuel oil (HFO) provides the advantages of using a single fuel source onboard ships for all engine power, but also requires attention directed to engine maintenance, reliability and emissions. MAN B&W Diesel in Holeby, Denmark, has a world reputation and substantial market share for HFO burning auxiliary engines above 500 kW. Offering a guaranteed 20000 operating hours before major overhaul on its HFO auxiliary gen-sets, the company has promoted the unifuel concept for ship propulsion and auxiliary power plants for many years. Based on this experience, a new generation of small HFO burning diesels has been designed. Low operating and maintenance costs, low initial cost, heavy fuel capabilities with unrestricted load profile, high reliability at long maintenance intervals and low emmisions were the main design targets. The design, specifications, and performance of these engines are discussed in this article.

  3. Effect of Charcoal Volatile Matter Content and Feedstock on Soil Microbe-Carbon-Nitrogen Dynamics

    NASA Astrophysics Data System (ADS)

    McClellan, T.; Deenik, J. L.; Hockaday, W. C.; Campbell, S.; Antal, M. J., Jr.

    2010-12-01

    Charcoal has important biogeochemical implications in soil—first as a means to sequester carbon, and second as a soil conditioner to potentially enhance soil quality and fertility. Volatile matter (VM) content is a property of charcoal which describes its degree of thermal alteration, or carbonization. Results from greenhouse experiments have shown that plant growth can be negatively affected by charcoals with high VM content (20-35%), with and without fertilizer supplements, whereas low VM charcoal (6-9%) increased plant growth when combined with fertilizer. We conducted two laboratory studies to characterize the VM content of charcoals derived from two feedstocks (corncob and kiawe) and relate observed differences to key aspects of soil fertility. Using Fourier transform infrared spectroscopy (FTIR), 13C nuclear magnetic resonance (NMR), total phenol content (using a Prussian blue colorimetric assay), and gas chromatography-mass spectrometry (GC-MS), we found that the VM content of charcoal primarily consisted of alkanes, oxygen-substituted alkanes, and phenolic compounds. However, the GC-MS data indicated that charcoals can differ vastly in their extractable fraction, depending upon both VM content and feedstock. In a second set of experiments, we examined the effect of VM content and feedstock on soil microbial activity, available nitrogen (N), and soluble carbon (C). High VM corncob charcoals significantly enhanced microbial activity, coupled with net reduction in available N and soluble C. For a given feedstock, the extent of this effect was dependent upon VM content. However, the overall effect of VM content on microbial dynamics was apparently related to the composition of the acetone-extractable fraction, which was particularly important when comparing two charcoals derived from different feedstocks but with the equivalent VM contents. Removing the acetone-extractable fraction from the 23% VM corncob charcoal significantly reduced the enhancement of

  4. Stripping of organic compounds from wastewater as an auxiliary fuel of regenerative thermal oxidizer.

    PubMed

    Chang, Meng-Wen; Chern, Jia-Ming

    2009-08-15

    Organic solvents with different volatilities are widely used in various processes and generate air and water pollution problems. In the cleaning processes of electronics industries, most volatile organic compounds (VOCs) are vented to air pollution control devices while most non-volatile organic solvents dissolve in the cleaning water and become the major sources of COD in wastewater. Discharging a high-COD wastewater stream to wastewater treatment facility often disturbs the treatment performance. A pretreatment of the high-COD wastewater is therefore highly desirable. This study used a packed-bed stripping tower in combination with a regenerative thermal oxidizer to remove the COD in the wastewater from a printed circuit board manufacturing process and to utilize the stripped organic compounds as the auxiliary fuel of the RTO. The experimental results showed that up to 45% of the COD could be removed and 66% of the RTO fuel could be saved by the combined treatment system.

  5. Utilization of unpeeled cassava (Manihot esculenta Crantz) root meal supplemented with or without charcoal by broiler chickens.

    PubMed

    Oso, A O; Akapo, O; Sanwo, K A; Bamgbose, A M

    2014-06-01

    A 42-day feeding trial was conducted using 480-day-old, male Marshall broilers to study the utilization of unpeeled cassava root meal (UCRM) supplemented with or without 6 g/kg charcoal. The experimental design was laid out in a 3 × 2 factorial arrangement of treatments having three inclusion levels of UCRM (0, 100 and 200 g/kg) with or without 6 g/kg charcoal supplementation. Each treatment consisted of 80 birds replicated eight times with 10 birds per replicate. Main effect of inclusion level of UCRM and supplementation of charcoal showed reduced (p < 0.05) final live weight, weight gain, feed intake and apparent crude protein digestibility of the birds with increasing inclusion levels of UCRM. Birds fed diets supplemented with charcoal showed higher (p < 0.05) final live weight, weight gain and feed intake than birds fed diets without charcoal. Supplementation of charcoal in diet containing 100 g/kg UCRM resulted in improved (p < 0.05) weight gain when compared with birds fed similar diet but not supplemented with charcoal. Broilers fed diet containing no UCRM but supplemented with charcoal had the highest overall (p < 0.05) final live weight and weight gain, while birds fed diet containing 200 g/kg UCRM supplemented with charcoal recorded the poorest (p < 0.05) final live weight and weight gain. Serum glutamate oxaloacetate transaminase (SGOT) and serum thiocyanate concentration increased (p < 0.05) with increasing dietary inclusion levels of UCRM. Dietary supplementation of charcoal resulted in increased (p < 0.05) concentration of serum glucose and cholesterol and reduced (p < 0.05) SGOT concentration. Birds fed diets containing UCRM had high (p < 0.05) serum thiocyanate concentration irrespective of dietary supplementation or not with 6 g/kg charcoal. In conclusion, supplementation of diet containing up to 100 g/kg UCRM with 6 g/kg charcoal showed improved weight gain without any deleterious effect on serum metabolites.

  6. Density-functional expansion methods: Generalization of the auxiliary basis

    PubMed Central

    Giese, Timothy J.; York, Darrin M.

    2011-01-01

    The formulation of density-functional expansion methods is extended to treat the second and higher-order terms involving the response density and spin densities with an arbitrary single-center auxiliary basis. The two-center atomic orbital products are represented by the auxiliary functions centered about those two atoms, and the mapping coefficients are determined from a local constrained variational procedure. This two-center variational procedure allows the mapping coefficients to be pretabulated and splined as a function of internuclear separation for efficient look up. The splines of mapping coefficients have a range no longer than that of the overlap integrals, and the auxiliary density appears as a single point-multipole expansion to all nonoverlapping atoms, thus allowing for the trivial implementation of a linear-scaling algorithm. The method is tested using Gaussian multipole expansions, and the effect of angular and radial completeness is explored. Several auxiliary basis sets are parametrized and compared to an auxiliary basis analogous to that used in the self-consistent-charge density-functional tight-binding model, and the method is demonstrated to greatly improve the representation of the density response with respect to a reference expansion model that does not use an auxiliary basis. PMID:21599040

  7. Stove having auxiliary damper operably connected to access door

    SciTech Connect

    Webb, J.E.

    1981-07-28

    A stove of the wood burning type is provided with a smoke passage having a main opening adjacent the access door of the stove and an auxiliary opening therein which is located further away from the access door and more closely adjacent the rear portion of the smoke passage and the chimney than the main opening. A regulator damper controls the rate of flow of products of combustion from the combustion chamber through the main opening and the smoke passage to the chimney, and an auxiliary damper normally closes the auxiliary opening when the access door is in a normally closed position. Apparatus is operably associated with the auxiliary damper and the stove access door for effecting movement of the auxiliary damper from the normally closed position to the opened position prior to the access door being opened for redirecting the products of combustion through the auxiliary opening and thus further away from the access door so as to thereby prevent the escapement of smoke through the stove access opening when the access door is opened.

  8. Using Principal Components as Auxiliary Variables in Missing Data Estimation.

    PubMed

    Howard, Waylon J; Rhemtulla, Mijke; Little, Todd D

    2015-01-01

    To deal with missing data that arise due to participant nonresponse or attrition, methodologists have recommended an "inclusive" strategy where a large set of auxiliary variables are used to inform the missing data process. In practice, the set of possible auxiliary variables is often too large. We propose using principal components analysis (PCA) to reduce the number of possible auxiliary variables to a manageable number. A series of Monte Carlo simulations compared the performance of the inclusive strategy with eight auxiliary variables (inclusive approach) to the PCA strategy using just one principal component derived from the eight original variables (PCA approach). We examined the influence of four independent variables: magnitude of correlations, rate of missing data, missing data mechanism, and sample size on parameter bias, root mean squared error, and confidence interval coverage. Results indicate that the PCA approach results in unbiased parameter estimates and potentially more accuracy than the inclusive approach. We conclude that using the PCA strategy to reduce the number of auxiliary variables is an effective and practical way to reap the benefits of the inclusive strategy in the presence of many possible auxiliary variables.

  9. Research on dye wastewater decoloration by pulse discharge plasma combined with charcoal derived from spent tea leaves.

    PubMed

    Wang, Tiecheng; Qu, Guangzhou; Pei, Shuzhao; Liang, Dongli; Hu, Shibin

    2016-07-01

    Pulsed discharge plasma (PDP) combined with charcoal (PDP-charcoal) was employed to treat dye wastewater, with methyl orange (MO) as the model pollutant. The charcoal was prepared using spent tea leaves and was characterized by scanning electron microscopy, Fourier-transform infrared spectroscopy, and Boehm titration to investigate the adsorption and catalytic characteristics before and after adsorption and PDP treatment. The prepared charcoal exhibited a high MO adsorption capacity, and the adsorption process followed the pseudo-second-order kinetic model and the Freundlich model. The MO decoloration efficiency reached 69.8 % within 7.5 min of treatment in the PDP-charcoal system, whereas values of 29.2 and 25.9 % were achieved in individual PDP and charcoal systems, respectively. The addition of n-butanol and H2PO4 (-) presented inhibitive effects on MO decoloration in the PDP system. However, these effects were much weaker in the PDP-charcoal system. In addition, the effects of charcoal on O3 and H2O2 formation were evaluated, and the results showed that both the O3 and H2O2 concentrations decreased in the presence of charcoal. The MO decomposition intermediates were analyzed using UV-Vis spectrometry and GC-MS. 1,4-Benzoquinone, 4-nitrophenol, 4-hydroxyaniline, and N,N'-dimethylaniline were detected. A possible pathway for MO decomposition in this system was proposed. PMID:27026548

  10. Research on dye wastewater decoloration by pulse discharge plasma combined with charcoal derived from spent tea leaves.

    PubMed

    Wang, Tiecheng; Qu, Guangzhou; Pei, Shuzhao; Liang, Dongli; Hu, Shibin

    2016-07-01

    Pulsed discharge plasma (PDP) combined with charcoal (PDP-charcoal) was employed to treat dye wastewater, with methyl orange (MO) as the model pollutant. The charcoal was prepared using spent tea leaves and was characterized by scanning electron microscopy, Fourier-transform infrared spectroscopy, and Boehm titration to investigate the adsorption and catalytic characteristics before and after adsorption and PDP treatment. The prepared charcoal exhibited a high MO adsorption capacity, and the adsorption process followed the pseudo-second-order kinetic model and the Freundlich model. The MO decoloration efficiency reached 69.8 % within 7.5 min of treatment in the PDP-charcoal system, whereas values of 29.2 and 25.9 % were achieved in individual PDP and charcoal systems, respectively. The addition of n-butanol and H2PO4 (-) presented inhibitive effects on MO decoloration in the PDP system. However, these effects were much weaker in the PDP-charcoal system. In addition, the effects of charcoal on O3 and H2O2 formation were evaluated, and the results showed that both the O3 and H2O2 concentrations decreased in the presence of charcoal. The MO decomposition intermediates were analyzed using UV-Vis spectrometry and GC-MS. 1,4-Benzoquinone, 4-nitrophenol, 4-hydroxyaniline, and N,N'-dimethylaniline were detected. A possible pathway for MO decomposition in this system was proposed.

  11. Charcoal-induced granuloma that mimicked a nodal metastasis on ultrasonography and FDG-PET/CT after neck dissection.

    PubMed

    Choi, Jin Woo; Moon, Won-Jin; Choi, Nami; Roh, Hong Gee; Kim, Mi Young; Kim, Na Ra; Moon, Sung Gyu; Chung, Hyun Woo; Lim, So Dug; Yang, Jung-Hyun

    2015-01-01

    Charcoal can be used for preoperative localization of metastatic lymph nodes in the neck. Charcoal remains stable without causing foreign body reactions during as hort period. However, foreign body reactions may develop if charcoal is left in situ for more than 6 months. We reported a case of charcoal granuloma mimicking local recurrence on fluorodeoxyglucose-positron emission tomography/computed tomography and ultrasonography in a 47-year-old woman who had cervical lymph node dissection due to metastatic invasive ductal carcinoma of the breast.

  12. Charcoal and the Record of Fire-related Sedimentation in Holocene Alluvial Sediments

    NASA Astrophysics Data System (ADS)

    Meyer, G. A.

    2006-12-01

    Over the last few decades, rising temperatures and ensuing severe wildfires in the western USA cordillera have provided the opportunity to examine processes and deposits of postfire sedimentation on alluvial fans and floodplains. Most events are generated by widespread surface runoff from intense convective-storm precipitation on severely burned slopes. Flow processes range from debris flow to sediment-charged water floods. Muddy debris flows best preserve coarse charcoal in fan deposits, whereas gravelly debris flows often comminute charcoal into fine particles. As charcoal remains suspended in high-energy hyperconcentrated and water floods, only their fine-grained deposits typically contain much charcoal. Charcoal is locally concentrated in low-energy fluvial deposits, but displays increasing evidence for reworking with distance from source. Charred vegetation and litter marking burned soil surfaces may be preserved under postfire fan and fluvial sediments. Modern deposits provide models for identification of Holocene fire-related sediments and estimates of paleofire severity. AMS 14C dating of discrete charcoal fragments allows sample selection to minimize errors of sample age > fire age. Fires are incompletely recorded in the event stratigraphy of one fan, but larger populations of 14C ages from numerous fans permit composite probability distributions that represent centennial- to millennial-scale changes in fire-related sedimentation across a study area. Records from Yellowstone and central Idaho indicate the large role of fire in episodic erosion across a range of conifer forests, most strongly during severe, multidecadal droughts in warmer periods (e.g. in Medieval time 900-1300 AD). In central Idaho, identification of charcoal macrofossils indicates broadly similar, aspect-controlled forest compositions over the last 3000 yr. Emerging data from the Sacramento Mountains, New Mexico, show rapid fan aggradation due to fire-related events in the warm middle

  13. Chemical recalcitrance of biochar and wildfire charcoal: how similar are they?

    NASA Astrophysics Data System (ADS)

    Santin, Cristina; Doerr, Stefan H.; Merino, Agustin

    2016-04-01

    The enhanced chemical resistance to biological degradation of pyrogenic materials, either produced during wildfires (charcoal) or by man (biochar), makes them long-term carbon sinks once incorporated in soils. In spite of their fundamental similarities, studies comparing the chemical recalcitrance of biochar and wildfire charcoal are scarce because analogous materials for accurate comparison are not easily available. Using solid-state 13C cross polarization-magic angle spinning nuclear magnetic resonance spectroscopy we characterized the chemical recalcitrance of pyrogenic materials generated from the same unburnt feedstooks (litter and dead wood from Pinus banksiana): (a) charcoal from a high-intensity wildfire and (b) biochar obtained by slow pyrolysis [3 treatments: 2 h at 350, 500 and 650°C]. For quantification, the spectra were divided into four regions representing different chemical environments of the 13C nucleus: alkyl C (0-45 ppm), O-alkyl C (45-110 ppm), olefinic and aromatic C(110-160 ppm), and carbonyl C (160-210 ppm). As an indicator of chemical recalcitrance, the degree of aromaticity (%) was calculated as follow: aromatic-C ∗ 100 / (alkyl C+ O alkyl-C + aromatic-C). The pyrogenic materials derived from wood show higher degrees of aromaticity (68 to 88%) than pyrogenic material derived from litter (40 to 88%). When comparing biochar and wildfire charcoal, biochars produced at 500 and 650°C always have higher degrees of aromaticity than wildfire charcoals, irrespective of the original feedstock. Wildfire charcoals always show a more heterogeneous chemical composition, with alkyl and O-alkyl compounds present even in charcoal generated at very high temperatures (temperatures up to 950 °C were recorded on the litter surface during the wildfire). However, biochars produced at 500 and 650 °C are mostly aromatic, and only the biochars produced at 350 °C show partial contribution of alkyl-C compounds. Our results suggest that biochar-type pyrogenic

  14. Dynamics and functions of bacterial communities in bark, charcoal and sand filters treating greywater.

    PubMed

    Dalahmeh, Sahar S; Jönsson, Håkan; Hylander, Lars D; Hui, Nan; Yu, Dan; Pell, Mikael

    2014-05-01

    This study explored the effects of greywater application on the dynamics and functions of biofilms developed in bark, activated charcoal and sand filters used for removal of organic matter and nitrogen. Duplicate columns (20 cm diameter, 60 cm deep) were packed with bark, charcoal or sand with effective size 1.4 mm and uniformity coefficient 2.2, and dosed with 32 L m(-2) day(-1) of an artificial greywater (14 g BOD5 m(-2) day(-1)) for 116 days. Potential respiration rate (PRR), determined in filter samples after addition of excess glucose, and bacterial diversity and composition, analysed by 454-pyrosequencing of bacterial 16S ribosomal DNA, were measured at different times and depths in the filters. The bark and charcoal filters were more efficient in removing BOD5 than the sand (98, 97% and 75%, respectively). The highest PRR in the 0-2 cm layer of the columns on day 84 was found in the bark filters, followed by the charcoal and sand filters (632 ± 66, 222 ± 34 and 56 ± 2 mg O2 L(-1), respectively; n = 2). Bacterial community in the bark filters showed the highest richness. The charcoal and sand filters both developed more diverse and dynamic (changing over time and depth) bacterial communities than the bark. In addition to the greywater, the lignocelluosic composition of the bark and its lower pH probably selected for the bacterial community structure and the organic content provided additional substrate, as shown by its higher PRR and its different nitrifying bacterial genera. In the oligotrophic charcoal and sand, the composition of the greywater itself defined the bacterial community. Thus, the initially low bacterial biomass in the latter filters was enriched over time, allowing a diversified bacterial community to develop. The top layers of the bark and charcoal filters displayed a high dominance of Rhizobium, Pseudomonas and Acinetobacter, which were less evident in the 60 cm layer, whereas in the sand filters these genera were

  15. 46 CFR 58.25-10 - Main and auxiliary steering gear.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Main and auxiliary steering gear. 58.25-10 Section 58.25... AUXILIARY MACHINERY AND RELATED SYSTEMS Steering Gear § 58.25-10 Main and auxiliary steering gear. (a) Power-operated main and auxiliary steering gear must be separate systems that are independent throughout...

  16. 46 CFR 58.25-10 - Main and auxiliary steering gear.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Main and auxiliary steering gear. 58.25-10 Section 58.25... AUXILIARY MACHINERY AND RELATED SYSTEMS Steering Gear § 58.25-10 Main and auxiliary steering gear. (a) Power-operated main and auxiliary steering gear must be separate systems that are independent throughout...

  17. Fluidized bed combustor modeling

    NASA Technical Reports Server (NTRS)

    Horio, M.; Rengarajan, P.; Krishnan, R.; Wen, C. Y.

    1977-01-01

    A general mathematical model for the prediction of performance of a fluidized bed coal combustor (FBC) is developed. The basic elements of the model consist of: (1) hydrodynamics of gas and solids in the combustor; (2) description of gas and solids contacting pattern; (3) kinetics of combustion; and (4) absorption of SO2 by limestone in the bed. The model is capable of calculating the combustion efficiency, axial bed temperature profile, carbon hold-up in the bed, oxygen and SO2 concentrations in the bubble and emulsion phases, sulfur retention efficiency and particulate carry over by elutriation. The effects of bed geometry, excess air, location of heat transfer coils in the bed, calcium to sulfur ratio in the feeds, etc. are examined. The calculated results are compared with experimental data. Agreement between the calculated results and the observed data are satisfactory in most cases. Recommendations to enhance the accuracy of prediction of the model are suggested.

  18. Fluidized bed combustion

    SciTech Connect

    Sowards, N.K.; Murphy, M.L.

    1991-10-29

    This patent describes a vessel. It comprises a fluid bed for continuously incinerating fuel comprising tire segments and the like which comprise metallic wire tramp and for concurrently removing tramp and bed materials at a bottom effluent exit means of the vessel, the vessel further comprising static air distributor means at the periphery of the bed comprising a substantially centrally unobstructed relatively large central region in which the fluid bed and fuel only are disposed and through which bed material and tramp migrate without obstruction to and through the effluent exit means, downwardly and inwardly stepped lower vessel wall means and a plurality of peripherally located centrally directed vertically and horizontally offset spaced air influent means surrounding the central region and associated with the stepped lower vessel wall means by which the bed is supported and fluidized.

  19. In vitro analysis of the effect of supplementation with activated charcoal on the equine hindgut.

    PubMed

    Edmunds, J L; Worgan, H J; Dougal, K; Girdwood, S E; Douglas, J-L; McEwan, N R

    2016-01-01

    The present study uses in vitro analytical techniques to investigate the effect of activated charcoal on the microbial community of the equine hindgut and the metabolites they produce. Incubations were performed in Wheaton bottles using a 50 ml incubation of a high-energy feed or a low-energy feed, plus bottles with no added food source, together with five levels of activated charcoal (0, 10, 25, 50 or 100 mg per bottle) and fecal samples as a bacterial inoculum. Using this method the rate of gas production, volatile fatty acid and ammonia concentrations, and pH values were analyzed and found to vary depending on the addition of feed, but the activated charcoal had no effect (P>0.05) on any of these. It is already believed that the effect of activated charcoal as a control for toxic substances is at its highest in the foregut or midgut of animals, and therefore should have little impact on the hindgut. The data presented here suggest that if any of the activated charcoal does reach the hindgut, then it has no significant impact on the microbial community present, nor on the major metabolites produced, and so should not have a detrimental effect on the principal site of fermentation in the horse.

  20. Contribution of sorbitol combined with activated charcoal in prevention of salicylate absorption.

    PubMed

    Keller, R E; Schwab, R A; Krenzelok, E P

    1990-06-01

    The use of cathartics and activated charcoal in treating toxic ingestions has become a standard treatment modality. Sorbitol has been shown to be the most rapidly acting cathartic, but its therapeutic significance has been debated. Using a previously described aspirin overdose model, ten healthy volunteers participated in a crossover design study that investigated the effect of activated charcoal alone versus that of activated charcoal and sorbitol in preventing salicylate absorption. In phase 1 of the study, subjects consumed 2.5 g aspirin followed by 25 g activated charcoal one hour later. Urine was collected for 48 hours and analyzed for quantitative salicylate metabolites. Phase 2 was identical except that 1.5 g/kg sorbitol was consumed with the activated charcoal. The mean amount of aspirin absorbed without the use of sorbitol was 1.26 +/- 0.15 g, whereas the mean absorption was 0.912 +/- 0.18 g with the addition of sorbitol. This is a 28% decrease in absorption of salicylates attributable to the use of sorbitol. The difference is significant at P less than .05 by the paired Student's t test. This study demonstrates that the addition of sorbitol significantly decreases drug absorption in a simulated drug overdose model. Effects on absorption in actual overdose situations and on patient outcome should be the subjects of further study. PMID:2188536

  1. Preoperative colonic lesion localization with charcoal nanoparticle tattooing for laparoscopic colorectal surgery.

    PubMed

    Wang, Wen; Wang, Rong; Wang, Yu; Yu, Li; Li, Dazhou; Huang, Sheng; Ma, Jun; Lin, Nan; Yang, Weijin; Chen, Xin; Liu, Bin; Lv, Ren; Liao, Lianming

    2013-12-01

    The efficiency and safety of charcoal nanoparticle tattooing in localizing unpalpable colonic small lesions for later laparoscopy is described. Twenty six patients were enrolled for this prospective study. Tumor sites were localized with charcoal nanoparticles during colonoscopy for later laparoscopic colorectal operations. In all patients, the entire colon was examined preoperatively by colonoscopy and 0.5 ml (5 mg) of charcoal nanoparticle was injected submucosally near lesions or polypectomy sites. During laparoscopic colorectal operations for these biopsy-proven tumors, tumors were easily identified. The mean resection margin was 3.13 +/- 2.01 cm. The mean length of resected intestinal segment was 12.69 +/- 4.39 cm. No tumor was found at the resection line as indicated by postoperative pathological examination. Most importantly, no wrong segment was resected. Thus we show that easy identification of tumor can be achieved by preoperative tattooing with charcoal nanoparticles. Further studies regarding the long-term tattooing of tumor with charcoal nanoparticles are warranted.

  2. In vitro analysis of the effect of supplementation with activated charcoal on the equine hindgut

    PubMed Central

    EDMUNDS, J.L.; WORGAN, H.J.; DOUGAL, K.; GIRDWOOD, S.E.; DOUGLAS, J.-L.; MCEWAN, N.R.

    2016-01-01

    ABSTRACT The present study uses in vitro analytical techniques to investigate the effect of activated charcoal on the microbial community of the equine hindgut and the metabolites they produce. Incubations were performed in Wheaton bottles using a 50 ml incubation of a high-energy feed or a low-energy feed, plus bottles with no added food source, together with five levels of activated charcoal (0, 10, 25, 50 or 100 mg per bottle) and fecal samples as a bacterial inoculum. Using this method the rate of gas production, volatile fatty acid and ammonia concentrations, and pH values were analyzed and found to vary depending on the addition of feed, but the activated charcoal had no effect (P>0.05) on any of these. It is already believed that the effect of activated charcoal as a control for toxic substances is at its highest in the foregut or midgut of animals, and therefore should have little impact on the hindgut. The data presented here suggest that if any of the activated charcoal does reach the hindgut, then it has no significant impact on the microbial community present, nor on the major metabolites produced, and so should not have a detrimental effect on the principal site of fermentation in the horse. PMID:27330398

  3. Tailoring the characteristics of carbonized wood charcoal by using different heating rates

    NASA Astrophysics Data System (ADS)

    Kwon, Gu-Joong; Kim, Dae-Young; Oh, Choong-Hyeon; Park, Byung-Ho; Kang, Joo-Hyon

    2014-05-01

    This study examined the characteristics of charcoals generated from White Lauan ( Pentacmecontorta) and Punah ( Tetrameristaglabra) by using different carbonization temperatures and heating rates. The scanning electron micrographs showed vestured pits in the White Lauan and raphide crystals in Punah as their respective anatomical characteristics. A slower heating rate resulted in a lower temperature to obtain the same amount of weight loss, regardless of the species being tested. A greater charcoal yield was obtained at a higher heating rate. The specific surface area was smaller in the charcoal produced at a higher carbonization temperature, but the heating rate had little effected. For both wood species, the axial compressive strength of the charcoal increased as the carbonization temperature was increased. The X-ray diffractograms of White Lauan and Punah woods heated at 1200°C indicated thermal decomposition of the crystal structure of cellulose, but no appreciable structural changes occurred under the tested heating rate conditions. Overall, the heating rate affected the charcoal yield but not the specific surface area, compressive strength, and crystal structure.

  4. In vitro analysis of the effect of supplementation with activated charcoal on the equine hindgut.

    PubMed

    Edmunds, J L; Worgan, H J; Dougal, K; Girdwood, S E; Douglas, J-L; McEwan, N R

    2016-01-01

    The present study uses in vitro analytical techniques to investigate the effect of activated charcoal on the microbial community of the equine hindgut and the metabolites they produce. Incubations were performed in Wheaton bottles using a 50 ml incubation of a high-energy feed or a low-energy feed, plus bottles with no added food source, together with five levels of activated charcoal (0, 10, 25, 50 or 100 mg per bottle) and fecal samples as a bacterial inoculum. Using this method the rate of gas production, volatile fatty acid and ammonia concentrations, and pH values were analyzed and found to vary depending on the addition of feed, but the activated charcoal had no effect (P>0.05) on any of these. It is already believed that the effect of activated charcoal as a control for toxic substances is at its highest in the foregut or midgut of animals, and therefore should have little impact on the hindgut. The data presented here suggest that if any of the activated charcoal does reach the hindgut, then it has no significant impact on the microbial community present, nor on the major metabolites produced, and so should not have a detrimental effect on the principal site of fermentation in the horse. PMID:27330398

  5. Bed rest in pregnancy.

    PubMed

    Bigelow, Catherine; Stone, Joanne

    2011-01-01

    The use of bed rest in medicine dates back to Hippocrates, who first recommended bed rest as a restorative measure for pain. With the formalization of prenatal care in the early 1900s, maternal bed rest became a standard of care, especially toward the end of pregnancy. Antepartum bed rest is a common obstetric management tool, with up to 95% of obstetricians utilizing maternal activity restriction in some way in their practice. Bed rest is prescribed for a variety of complications of pregnancy, from threatened abortion and multiple gestations to preeclampsia and preterm labor. Although the use of bed rest is pervasive, there is a paucity of data to support its use. Additionally, many well-documented adverse physical, psychological, familial, societal, and financial effects have been discussed in the literature. There have been no complications of pregnancy for which the literature consistently demonstrates a benefit to antepartum bed rest. Given the well-documented adverse effects of bed rest, disruption of social relationships, and financial implications of this intervention, there is a real need for scientific investigation to establish whether this is an appropriate therapeutic modality. Well-designed randomized, controlled trials of bed rest versus normal activity for various complications of pregnancy are required to lay this debate to rest once and for all. PMID:21425272

  6. Highly stable rice-straw-derived charcoal in 3700-year-old ancient paddy soil: evidence for an effective pathway toward carbon sequestration.

    PubMed

    Wu, Mengxiong; Yang, Min; Han, Xingguo; Zhong, Ting; Zheng, Yunfei; Ding, Pin; Wu, Weixiang

    2016-01-01

    Recalcitrant charcoal application is predicted to decelerate global warming through creating a long-term carbon sink in soil. Although many studies have showed high stability of charcoal derived from woody materials, few have focused on the dynamics of straw-derived charcoal in natural environment on a long timescale to evaluate its potential for agricultural carbon sequestration. Here, we examined straw-derived charcoal in an ancient paddy soil dated from ~3700 calendar year before present (cal. year BP). Analytical results showed that soil organic matter consisted of more than 25% of charcoal in charcoal-rich layer. Similarities in morphology and molecular structure between the ancient and the fresh rice-straw-derived charcoal indicated that ancient charcoal was derived from rice straw. The lower carbon content, higher oxygen content, and obvious carbonyl of the ancient charcoal compared with fresh rice straw charcoal implied that oxidation occurred in the scale of thousands years. However, the dominant aromatic C of ancient charcoal indicated that rice-straw-derived charcoal was highly stable in the buried paddy soil due to its intrinsic chemical structures and the physical protection of ancient paddy wetland. Therefore, it may suggest that straw charcoal application is a potential pathway for C sequestration considering its longevity.

  7. Calibration of diffusion barrier charcoal detectors and application to radon sampling in dwellings

    NASA Astrophysics Data System (ADS)

    Cabrera, M. E. M.; Sujo, L. C.; Villalba, L.; Peinado, J. S.; Jimenez, A. C.; Baca, A. M.; Gandara, S. D.; Villalobos, M. R.; Miranda, A. L.; Peraza, E. F. H.

    2003-10-01

    Some calibration conditions of diffusion barrier charcoal canister (DBCC) detectors for measuring radon concentration in air were studied. A series of functional expressions and graphs were developed to describe relationship between radon concentration in air and the activity adsorbed in DBCC, when placed in small chambers. A semi-empirical expression for the DBCC calibration was obtained, based on the detector integration time and the adsorption coefficient of radon on activated charcoal. Both, the integration time for 10% of DBCC of the same batch, and the adsorption coefficient of radon for the activated charcoal used in these detectors, were experimentally determined. Using these values as the calibration parameters, a semi-empirical calibration function was used for the interpretation of the radon activities in the detectors used for sampling more than 200 dwellings in the major cities of the state of Chihuahua, Mexico.

  8. [Charcoal burners and carbon monoxide poisoning--help came from a scientific journal].

    PubMed

    Wasberg, G C

    2001-03-30

    The breakthrough for professional journals came in the 18th century. In 1972, Hans (Johannes) Möller (1736-96), a district physician in Bratsberg County, published an article in Topographisk Journal for Norge on carbon monoxide poisoning among charcoal burners, advising on the prevention of injuries and giving guidelines for treatment. This was in the heyday of Norwegian iron mills powered by charcoal, with charcoal burners paying a heavy price in the form of numerous fatal accidents. Möller's article was based on his experience with the local iron mill at Fritzøe. It solved a problem in this major branch of industry. Rationalist clergymen spread his advice among the general public for whom it was intended. Möller's scientific work also found an audience abroad. In 1801, five years after his death, the article was translated into German and published in a recognised German journal.

  9. Emissions of air toxics from a simulated charcoal kiln. Final report, October 1997--September 1998

    SciTech Connect

    Lemieux, P.M.

    1999-06-01

    The report gives results of experiments in a laboratory-scale charcoal kiln simulator to evaluate emissions of hazardous air pollutants from the production of charcoal in Missouri-type kilns. Fixed combustion gases were measured using continuous monitors. In addition, other pollutants, including methanol, volatile organic compounds, semivolatile organic compounds, and particle emission rates and size distributions were measured using various techniques. Emissions of all pollutants are reported in units of grams emitted per unit mass of initial wood converted to charcoal. Two burn conditions--slow and fast--were examined. High levels of methanol, benzene, and fine particulate were emitted in all tests. The estimated emissions from the fast burn conditions were significantly higher than those from the slow burn conditions.

  10. A means to make open-face charcoal detectors respond correctly to varying concentration radon fields

    SciTech Connect

    Distenfeld, C.H.

    1995-12-31

    Ronca-Battista and D. Gray 87, outlined the poor response of open-face charcoal detectors to varying concentration radon fields. At worst, for two day exposures with open-face charcoal canisters, their Table 4 indicated a 75% under-response for radon concentrations that were 10 times higher during the first day of two, 10:1. TCS has made similar measurements with open-faced and diffusion barrier detectors in 20:1, 1:20, and 1:1 fields. For the worst case 20:1, measurements indicate TCS two day open-face canisters under respond by 50%, while the Cohen and TCS diffusion barrier devices under responded by about 37%. The reasons for the under response are radon diffusion out of the charcoal due to the forces of lower concentration during the second half of the exposure, and uncompensated radioactive decay of radon gas.

  11. Development and optimization of the activated charcoal suspension composition based on a mixture design approach.

    PubMed

    Ronowicz, Joanna; Kupcewicz, Bogumiła; Pałkowski, Łukasz; Krysiński, Jerzy

    2015-03-01

    In this study, a new drug product containing activated charcoal was designed and developed. The excipient levels in the pharmaceutical formulation were optimized using a mixture design approach. The adsorption power of the activated charcoal suspension was selected as the critical quality attribute influencing the efficacy of medical treatment. Significant prognostic models (p<0.05) were obtained to describe in detail the interrelations between excipient levels and the adsorption power of the formulation. Liquid flavour had a critical impact on the adsorption power of the suspension. Formulations containing the largest amount of liquid flavour showed the lowest adsorption power. Sorbitol was not adsorbed onto activated charcoal so strongly as liquid flavour. A slight increase in the content of carboxymethylcellulose sodium led to a marked decrease in adsorption power. The obtained mathematical models and response surface allowed selection of the optimal composition of excipients in a final drug product.

  12. Analysis of alkyl nitrates and selected halocarbons in the ambient atmosphere using a charcoal preconcentration technique

    SciTech Connect

    Atlas, E.; Schauffler, S. )

    1991-01-01

    A method has been developed to measure {ge}C{sub 3} alkyl nitrates and C{sub 1}-C{sub 2} halocarbons, such as perchloroethylene and bromoform, in ambient air. The method preconcentrates analytes on a 5-mg charcoal trap from multiliter volumes of air. Analytes are desorbed from the charcoal with a small volume of solvent and are analyzed by high-resolution gas chromatography with electron capture detection. Laboratory and field tests have been performed to evaluate method precision, analyte breakthrough, and compound recovery from the charcoal. Tests verified that the sampling/analytical system is free from artifact formation under clean to moderately polluted conditions, but further tests are required for areas of high concentrations of hydrocarbons, NO{sub x}, and oxidants. The method allows measurement of halocarbons and {ge}C{sub 3} alkyl nitrates at concentrations in the pptv range.

  13. Molecular and structural properties of polymer composites filled with activated charcoal particles

    NASA Astrophysics Data System (ADS)

    Tahir, Dahlang; Liong, Syarifuddin; Bakri, Fahrul

    2016-03-01

    We have studied the molecular properties, structural properties, and chemical composition of composites by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) spectroscopy, and X-ray fluorescence (XRF) spectroscopy, respectively. FTIR spectra shows absorption band of hydroxyl group (-OH), methyl group (-CH3) and aromatic group (C-C). The absorption band for aromatic group (C-C) shows the formation of carbonaceous in composites. XRF shows chemical composition of composites, which the main chemicals are SO3, Cl, and ZnO. The loss on ignition value (LOI) of activated charcoal indicates high carbonaceous matter. The crystallite size for diffraction pattern from hydrogel polymer is about 17 nm and for activated charcoal are about 19 nm. The crystallite size of the polymer is lower than that of activated charcoal, which make possible of the particle from filler in contact with each other to form continuous conducting polymer through polymer matrix.

  14. Emissions from street vendor cooking devices (charcoal grilling). Final report, January 1998--March 1999

    SciTech Connect

    Lee, S.Y.

    1999-06-01

    The report discusses a joint US/Mexican program to establish a reliable emissions inventory for street vendor cooking devices (charcoal grilling), a significant source of air pollutants in the Mexicali-Imperial Valley area of Mexico. Emissions from these devices, prevalent in the streets of Mexicali, Mexico, were investigated experimentally by measuring levels of particulate matter, particle size distributions, volatile and semivolatile organic compounds, aldehydes, and oxides of nitrogen and sulfur, emitted when meat is cooked on a grill over a charcoal fire. To investigate the emission rate, both beef and chicken were tested. Furthermore, both meats were marinated with a mixture similar to that used by the street vendors. Some tests were conducted with non-marinated beef for comparison. Two blank runs were performed sampling charcoal fires without meat. Finally, a simple control device, normally used in an exhaust fan to trap grease over a kitchen stove, was evaluated for its effectiveness in reducing emissions.

  15. Impact of ancient charcoal kilns on chemical properties of several forest soils after 2 centuries

    NASA Astrophysics Data System (ADS)

    Dufey, Joseph; Hardy, Brieuc; Cornelis, Jean-Thomas

    2014-05-01

    Pyrogenic carbon plays a major role in soil biogeochemical processes and carbon budgets. Until the early 19th century, charcoal was the unique combustible used for iron metallurgy in Wallonia (Belgium). Traditional charcoal kilns were built directly in the forest: wood logs were piled into a mound and isolated from air oxygen with a covering of vegetation residues and soil before setting fire, inducing wood pyrolysis. Nowadays, ancient wood-charring platforms are still easy to identify on the forest floor as heightened domes of 10 meters in diameter characterized by a very dark topsoil horizon containing charcoal dust and fragments. Our goal is to assess the effects of wood charring at mound kiln sites on the properties of various forest soil types in Wallonia (Belgium), after two centuries. We sampled soil by horizon in 18 ancient kiln sites to 1.20 meter depth. The adjacent charcoal-unaffected soils were sampled the same way. We also collected recent charcoal fragments and topsoil samples from a still active charcoal kiln located close to Dole (France) to apprehend the evolution of soil properties over time. The pH, total carbon (C) and nitrogen (N) content, available phosphorus (Pav), cation exchange capacity at pH 7 (CEC), exchangeable cations (Ca++, Mg++, K+, Na+) and loss on ignition at 550°C (LI550) were measured on each soil sample. We separated the soil profiles in 5 groups based on the nature of soil substrate and pedogenesis for interpretation of the results. We show that the total carbon stock is significantly increased at kiln sites due to higher C concentrations and greater depth of the organo-mineral horizon. The C/N ratio in charcoal-enriched soil horizons is significantly higher than in the neighboring reference soils but clearly attenuated compared to pure wood-charcoal fragments. The CEC is higher in the charcoal-enriched soil horizons, not only due to higher C concentrations but also to increased CEC by carbon unit at kiln sites. The high

  16. Soil stratigraphy of charcoal kiln remains (CKR) in the Litchfield Hills, CT, USA

    NASA Astrophysics Data System (ADS)

    Raab, Thomas; Hirsch, Florian; Ouimet, Will; Dethier, David

    2016-04-01

    Charcoal kiln relicts (CKRs) are small anthropogenic landforms that are often found in historic mining areas. CKRs have not been a big research topic yet but mainly were studied as by-products of archaeological excavations. In the last years newly available and very accurate Digital Elevation Models (DEMs) based on high-resolution Airborne Laser Scanning (ALS) data have been used to identify these archaeological remains. In addition, findings of several thousands CKRs in the North German Lowland have increased the awareness that historical charcoal production may significantly contribute to Late Holocene landscape change. Besides the archaeological aspect of CKRs, potential impacts of charcoal burning on the ecology of modern soil landscapes and ecosystem processes must be considered. A relatively high density of CKRs is found in the Litchfield Hills nearby the town of West Cornwall, Litchfield County, CT, USA. The CKRs are especially well preserved on slopes of the tributary valleys of the Housatonic River and form little, circular ramparts with diameters normally less than ten meters. First, rough field surveys in Litchfield County in spring 2015 have suggested differences between soils inside and outside the CKR. Soils on the CKR seem to have relatively deep humus-rich and charcoal containing topsoils whereas the topsoils outside the CKR appear typically thinner and less rich in humus. More thorough investigations have been started in autumn 2015 to prove the hypothesis that properties, distribution and development of soils are controlled by archaeological remains of historical charcoal burning. We present preliminary results from our field studies conducted in October 2015. The stratigraphy and the extent of the 26 CKRs were studied using a sedimentological-pedological approach by coring and trenching. Our results indicate that in Litchfield County the CKRs were used twice and in quick succession. Before the second reuse, the rim of the platform was stabilized

  17. Gate drive latching circuit for an auxiliary resonant commutation circuit

    NASA Technical Reports Server (NTRS)

    Delgado, Eladio Clemente (Inventor); Kheraluwala, Mustansir Hussainy (Inventor)

    1999-01-01

    A gate drive latching circuit for an auxiliary resonant commutation circuit for a power switching inverter includes a current monitor circuit providing a current signal to a pair of analog comparators to implement latching of one of a pair of auxiliary switching devices which are used to provide commutation current for commutating switching inverters in the circuit. Each of the pair of comparators feeds a latching circuit which responds to an active one of the comparators for latching the associated gate drive circuit for one of the pair of auxiliary commutating switches. An initial firing signal is applied to each of the commutating switches to gate each into conduction and the resulting current is monitored to determine current direction and therefore the one of the switches which is carrying current. The comparator provides a latching signal to the one of the auxiliary power switches which is actually conducting current and latches that particular power switch into an on state for the duration of current through the device. The latching circuit is so designed that the only time one of the auxiliary switching devices can be latched on is during the duration of an initial firing command signal.

  18. Fluidized bed calciner apparatus

    DOEpatents

    Owen, Thomas J.; Klem, Jr., Michael J.; Cash, Robert J.

    1988-01-01

    An apparatus for remotely calcining a slurry or solution feed stream of toxic or hazardous material, such as ammonium diurante slurry or uranyl nitrate solution, is disclosed. The calcining apparatus includes a vertical substantially cylindrical inner shell disposed in a vertical substantially cylindrical outer shell, in which inner shell is disposed a fluidized bed comprising the feed stream material to be calcined and spherical beads to aid in heat transfer. Extending through the outer and inner shells is a feed nozzle for delivering feed material or a cleaning chemical to the beads. Disposed in and extending across the lower portion of the inner shell and upstream of the fluidized bed is a support member for supporting the fluidized bed, the support member having uniform slots for directing uniform gas flow to the fluidized bed from a fluidizing gas orifice disposed upstream of the support member. Disposed in the lower portion of the inner shell are a plurality of internal electric resistance heaters for heating the fluidized bed. Disposed circumferentially about the outside length of the inner shell are a plurality of external heaters for heating the inner shell thereby heating the fluidized bed. Further, connected to the internal and external heaters is a means for maintaining the fluidized bed temperature to within plus or minus approximately 25.degree. C. of a predetermined bed temperature. Disposed about the external heaters is the outer shell for providing radiative heat reflection back to the inner shell.

  19. High-speed ultrashort pulse fiber ring laser using charcoal nanoparticles.

    PubMed

    Li, Wenbo; Hu, Hongyu; Zhang, Xiang; Zhao, Shuai; Fu, Kan; Dutta, Niloy K

    2016-03-20

    A mode-locked erbium-doped fiber ring laser that is easy to set up is proposed and experimentally demonstrated to generate a high-repetition-rate optical pulse train with an ultrashort pulse width. The laser combines a rational harmonic mode-locking technique and charcoal nanoparticles as saturable absorbers. Compared to a solely active mode-locking scheme, the scheme with charcoal nanoparticles can remove the supermodes and narrow the pulse width by a factor of 0.57 at a repetition rate of 20 GHz. Numerical simulation of the laser performance is also provided, which shows good agreement with the experimental results. PMID:27140546

  20. The charcoal trap: Miombo forests and the energy needs of people

    PubMed Central

    2011-01-01

    Background This study evaluates the carbon dioxide and other greenhouse gas fluxes to the atmosphere resulting from charcoal production in Zambia. It combines new biomass and flux data from a study, that was conducted in a miombo woodland within the Kataba Forest Reserve in the Western Province of Zambia, with data from other studies. Results The measurements at Kataba compared protected area (3 plots) with a highly disturbed plot outside the forest reserve and showed considerably reduced biomass after logging for charcoal production. The average aboveground biomass content of the reserve (Plots 2-4) was around 150 t ha-1, while the disturbed plot only contained 24 t ha-1. Soil carbon was not reduced significantly in the disturbed plot. Two years of eddy covariance measurements resulted in net ecosystem exchange values of -17 ± 31 g C m-2 y-1, in the first and 90 ± 16 g C m-2 in the second year. Thus, on the basis of these two years of measurement, there is no evidence that the miombo woodland at Kataba represents a present-day carbon sink. At the country level, it is likely that deforestation for charcoal production currently leads to a per capita emission rate of 2 - 3 t CO2 y-1. This is due to poor forest regeneration, although the resilience of miombo woodlands is high. Better post-harvest management could change this situation. Conclusions We argue that protection of miombo woodlands has to account for the energy demands of the population. The production at national scale that we estimated converts into 10,000 - 15,000 GWh y-1 of energy in the charcoal. The term "Charcoal Trap" we introduce, describes the fact that this energy supply has to be substituted when woodlands are protected. One possible solution, a shift in energy supply from charcoal to electricity, would reduce the pressure of forests but requires high investments into grid and power generation. Since Zambia currently cannot generate this money by itself, the country will remain locked in the

  1. Soil Charcoal to Assess the Impacts of Past Human Disturbances on Tropical Forests

    PubMed Central

    Vleminckx, Jason; Morin-Rivat, Julie; Biwolé, Achille B.; Daïnou, Kasso; Gillet, Jean-François; Doucet, Jean-Louis; Drouet, Thomas; Hardy, Olivier J.

    2014-01-01

    The canopy of many central African forests is dominated by light-demanding tree species that do not regenerate well under themselves. The prevalence of these species might result from ancient slash-and-burn agricultural activities that created large openings, while a decline of these activities since the colonial period could explain their deficit of regeneration. To verify this hypothesis, we compared soil charcoal abundance, used as a proxy for past slash-and-burn agriculture, and tree species composition assessed on 208 rainforest 0.2 ha plots located in three areas from Southern Cameroon. Species were classified in regeneration guilds (pioneer, non-pioneer light-demanding, shade-bearer) and characterized by their wood-specific gravity, assumed to reflect light requirement. We tested the correlation between soil charcoal abundance and: (i) the relative abundance of each guild, (ii) each species and family abundance and (iii) mean wood-specific gravity. Charcoal was found in 83% of the plots, indicating frequent past forest fires. Radiocarbon dating revealed two periods of fires: “recent” charcoal were on average 300 years old (up to 860 BP, n = 16) and occurred in the uppermost 20 cm soil layer, while “ancient” charcoal were on average 1900 years old (range: 1500 to 2800 BP, n = 43, excluding one sample dated 9400 BP), and found in all soil layers. While we expected a positive correlation between the relative abundance of light-demanding species and charcoal abundance in the upper soil layer, overall there was no evidence that the current heterogeneity in tree species composition can be explained by charcoal abundance in any soil layer. The absence of signal supporting our hypothesis might result from (i) a relatively uniform impact of past slash-and-burn activities, (ii) pedoturbation processes bringing ancient charcoal to the upper soil layer, blurring the signal of centuries-old Human disturbances, or (iii) the prevalence of other

  2. Chemical and biological characterization of emissions from small residential stoves burning wood and charcoal

    SciTech Connect

    Ramdahl, T.; Alfheim, I.; Rustad, S.; Olsen, T.

    1982-01-01

    Emissions from a small residential wood stove and a newly developed residential stove burning charcoal have been characterized by chemical analysis and mutagenicity testing (Ames Salmonella test). For wood burning the samples were taken under normal and starved air conditions burning birch and spruce separately. The burning conditions in the stove seemed to influence the emissions to a larger extent than the type of wood. The emissions of aldehydes, benzene and polycyclic aromatic hydrocarbons from the charcoal-burning stove are lower by a factor of 25-1000 as compared to the wood stove. The mutagenicity of the emissions showed a similar trend.

  3. Holocene Fire History of an Eastern Oregon Forest Based on Soil Charcoal Radiocarbon Dates

    NASA Astrophysics Data System (ADS)

    Carson, R. J.; Malkemus, D.; Clifton, C. F.

    2006-12-01

    Limited research has been done on long-term forest fire histories in northeastern Oregon. As part of an investigation to determine the minimum age of a 300 ha landslide in the Blue Mountains, a pit was excavated near the toe of the slide. The pit, located in a depression between the landslide and a ridge, contains massive clays and silts, and an 8000-year sequence of forest fires recorded in 7 buried charcoal layers. Eight- thousand-year-old Mazama Ash (Crater Lake, Oregon) is common in the area, but no tephra was found in the excavation. The upper 17 cm is organic rich soil. Seven horizons of charcoal are present; the upper six are subhorizontal and occur at depths of 17, 36, 41, 46, 52, and 57 cm. The lowest charcoal horizon follows a disconformity that cuts diagonally across the pit from 85 to 125 cm below the surface; oxidation in the form of orange mottling occurs above this disconformity (interpreted to be a paleoslope) and is prominent below it. The charcoal horizons provide evidence of large-scale forest fires in the vicinity, with differing intensities represented by the amount of charcoal in each horizon. The layers vary in thickness from 2 to 6 cm. Five charcoal horizons were radiocarbon dated (AMS) and calendar calibrated. The charcoal at the base of the soil (at 17 cm) provided an age of AD 1670 to 1960; this horizon correlates with widespread fires in the Blue Mountains in AD 1855. The horizon second closest to the surface (at 36 cm) provided an age of 1310 ± 40 B.P. The thickest horizon (at 46 cm) yielded an age of 2420 ± 40 B.P. The lowest horizontal horizon (at 57 cm) provided an age of 3460 ± 40 B.P. The lowest charcoal (at the disconformity) yielded an age of 7990 ± 40 B.P. Based on radiocarbon dates, the mean rate of sedimentation in the closed depression is approximately 1.2 cm/century. Fire episodes (which correspond remarkably well with a lake core site approximately 150 km south), indicate relatively long periods (from 400 to over 4000

  4. Research on Bamboo Charcoal Bonded Grinding Wheel and Its Mechanical Properties

    NASA Astrophysics Data System (ADS)

    Li, Wei; Xu, Minjie; Zhan, Fangyong; Jin, Mingsheng

    2014-08-01

    In this paper, a new type of grinding wheel and its manufacturing production process are introduced. The new BCB (Bamboo Charcoal Bond) grinding wheel was made of bamboo charcoal, phenolic resin and abrasive powder with higher press and temperature. To investigate its mechanical features, such as Rockwell hardness, resistance to abrasion, and resistance to pressure, some experiments on three BCB samples with different Resin weight ratios 20%, 25%, 30%, were carried out. The results showed that the BCB sample with proper moulding process and Resin weight ratio had better performance.

  5. USE OF POWDERED COCONUT CHARCOAL AS A TOXICITY IDENTIFICATION AND EVALUATION MANIPULATION FOR ORGANIC TOXICANTS IN MARINE SEDIMENTS

    EPA Science Inventory

    We report on a procedure using powdered coconut charcoal to sequester organic contaminants and reduce toxicity in sediments as part of a series of toxicity identification and evaluation (TIE) methods. Powdered coconut charcoal (PCC) was effective in reducing the toxicity of endos...

  6. What Does Psychological Autopsy Study Tell Us about Charcoal Burning Suicide--A New and Contagious Method in Asia?

    ERIC Educational Resources Information Center

    Chan, Sandra S. M.; Chiu, Helen F. K.; Chen, Eric Y. H.; Chan, Wincy S. C.; Wong, Paul W. C.; Chan, Cecilia L. W.; Law, Y. W.; Yip, Paul S. F.

    2009-01-01

    Charcoal burning suicides in Hong Kong between 2002-2004 in the 15 to 59-year-old age group were investigated using the psychological autopsy method. The psychopathological profiles of charcoal burning suicides (N = 53) were compared against "other suicides" (N = 97). The two groups did not differ significantly in the prevalence of "DSM-IV" axis I…

  7. Reliability model of a monopropellant auxiliary propulsion system

    NASA Technical Reports Server (NTRS)

    Greenberg, J. S.

    1971-01-01

    A mathematical model and associated computer code has been developed which computes the reliability of a monopropellant blowdown hydrazine spacecraft auxiliary propulsion system as a function of time. The propulsion system is used to adjust or modify the spacecraft orbit over an extended period of time. The multiple orbit corrections are the multiple objectives which the auxiliary propulsion system is designed to achieve. Thus the reliability model computes the probability of successfully accomplishing each of the desired orbit corrections. To accomplish this, the reliability model interfaces with a computer code that models the performance of a blowdown (unregulated) monopropellant auxiliary propulsion system. The computer code acts as a performance model and as such gives an accurate time history of the system operating parameters. The basic timing and status information is passed on to and utilized by the reliability model which establishes the probability of successfully accomplishing the orbit corrections.

  8. The performance of charcoal-based radon detection under time-varying radon conditions: Experimental and theoretical results

    SciTech Connect

    Sextro, R.G.; Lee, D.D.

    1988-10-01

    Radon adsorption by charcoal is a widely used technique for measuring indoor radon concentration, particularly when short-term results are desired. There are several different devices available, ranging from permeable envelopes filled with charcoal and open-face charcoal-filled canisters to devices incorporating diffusion limiting features to reduce losses of radon due to desorption. However, the integration characteristics of these samplers are not well understood, particularly under conditions of highly varying radon concentrations. A model for predicting the response of various types of charcoal based detectors to time-variant radon concentrations has been developed; the model predictions compare well with results from chamber experiments. Both the experimental and theoretical results have also been compared with integrated continuous-sampling measurements. The implications of these comparisons for use of charcoal for screening measurements is discussed. 5 refs., 4 figs., 2 tabs.

  9. X-15 auxiliary power units and reaction controls

    NASA Technical Reports Server (NTRS)

    Wagner, Bruce O

    1958-01-01

    Electrical and hydraulic power within the X-15 airplane is developed by a monopropellant auxiliary power unit. In addition, airplane altitude control at extreme altitude is by monopropellant rockets. Two duplicate installations are used to provide reliability beyond single-system capabilities to assure continuous availability of aerodynamic flight controls and space-altitude controls. All components have been developed and evaluation tested by the individual suppliers. The principal item, the auxiliary power unit, has completed a 150 hour endurance test comprising 300 typical mission duty cycles. (author)

  10. Radio frequency-compensated Langmuir probe with auxiliary double probes

    SciTech Connect

    Oh, Se-Jin; Oh, Seung-Ju; Chung, Chin-Wook

    2010-09-15

    A radio frequency (rf) compensation design using auxiliary double probes connected in parallel with a main measurement probe was developed for Langmuir probe diagnostics. This probe structure can reduce the sheath impedance of the main probe. In our probe design, the sheath capacitance of the probe can be increased and its sheath resistance can be decreased with increasing dc bias differential voltage between the auxiliary double probes. The I-V characteristic curve and electron energy distribution functions measured by our probe system had sufficient rf compensation performance in inductively coupled plasmas.

  11. Radio frequency-compensated Langmuir probe with auxiliary double probes.

    PubMed

    Oh, Se-Jin; Oh, Seung-Ju; Chung, Chin-Wook

    2010-09-01

    A radio frequency (rf) compensation design using auxiliary double probes connected in parallel with a main measurement probe was developed for Langmuir probe diagnostics. This probe structure can reduce the sheath impedance of the main probe. In our probe design, the sheath capacitance of the probe can be increased and its sheath resistance can be decreased with increasing dc bias differential voltage between the auxiliary double probes. The I-V characteristic curve and electron energy distribution functions measured by our probe system had sufficient rf compensation performance in inductively coupled plasmas.

  12. New braneworld models in the presence of auxiliary fields

    SciTech Connect

    Bazeia, D.; Marques, M.A.; Menezes, R.; Moreira, D.C.

    2015-10-15

    We study braneworld models in the presence of auxiliary fields. We use the first-order framework to investigate several distinct possibilities, where the standard braneworld scenario changes under the presence of the parameter that controls the auxiliary fields introduced to modify Einstein’s equation. The results add to previous ones, to show that the minimal modification that we investigate contributes to change quantitatively the thick braneworld profile, although no new qualitative effect is capable of being induced by the minimal modification here considered.

  13. Efficient auxiliary-mode approach for time-dependent nanoelectronics

    NASA Astrophysics Data System (ADS)

    Popescu, Bogdan Stefan; Croy, Alexander

    2016-09-01

    A new scheme for numerically solving the equations arising in the time-dependent non-equilibrium Green's function formalism is developed. It is based on an auxiliary-mode expansion of the self-energies which convert the complicated set of integro-differential equations into a set of ordinary differential equations. In the new scheme all auxiliary matrices are replaced by vectors or scalars. This drastically reduces the computational effort and memory requirements of the method, rendering it applicable to topical problems in electron quantum optics and molecular electronics. As an illustrative example we consider the dynamics of a Leviton wave-packet in a 1D wire.

  14. History of Sandia National Laboratories` auxiliary closure mechanisms

    SciTech Connect

    Weydert, J.C.; Ponder, G.M.

    1993-12-01

    An essential component of a horizontal, underground nuclear test setup at the Nevada Test Site is the auxiliary closure system. The massive gates that slam shut immediately after a device has been detonated allow the prompt radiation to pass, but block debris and hot gases from continuing down the tunnel. Thus, the gates protect experiments located in the horizontal line-of-sight steel pipe. Sandia National Laboratories has been the major designer and developer of these closure systems. This report records the history of SNL`s participation in and contributions to the technology of auxiliary closure systems used in horizontal tunnel tests in the underground test program.

  15. Bathing a patient in bed

    MedlinePlus

    Bed bath; Sponge bath ... Some patients cannot safely leave their beds to bathe. For these people, daily bed baths can help keep their skin healthy, control odor, and increase comfort. If moving the ...

  16. Influence of production variables and starting material on charcoal stable isotopic and molecular characteristics

    NASA Astrophysics Data System (ADS)

    Ascough, P. L.; Bird, M. I.; Wormald, P.; Snape, C. E.; Apperley, D.

    2008-12-01

    We present a systematic study on the effect of starting species, gas composition, temperature, particle size and duration of heating upon the molecular and stable isotope composition of high density (mangrove) and low density (pine) wood. In both pine and mangrove, charcoal was depleted in δ 13C relative to the starting wood by up to 1.6‰ and 0.8‰, respectively. This is attributed predominantly to the progressive loss of isotopically heavier polysaccharides, and kinetic effects of aromatization during heating. However, the pattern of δ 13C change was dependant upon both starting species and atmosphere, with different structural changes associated with charcoal production from each wood type elucidated by Solid-State 13C Nuclear Magnetic Resonance Spectroscopy. These are particularly evident at lower temperatures, where variation in the oxygen content of the production atmosphere results in differences in the thermal degradation of cellulose and lignin. It is concluded that production of charcoal from separate species in identical conditions, or from a single sample exposed to different production variables, can result in significantly different δ 13C of the resulting material, relative to the initial wood. These results have implications for the use of charcoal isotope composition to infer past environmental change.

  17. 40 CFR 454.10 - Applicability; description of the manufacture of char and charcoal briquets subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the manufacture of char and charcoal briquets subcategory. 454.10 Section 454.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GUM AND WOOD...

  18. Refinement of the charcoal meal study by reduction of the fasting period.

    PubMed

    Prior, Helen; Ewart, Lorna; Bright, Jonathan; Valentin, Jean-Pierre

    2012-05-01

    The aim of this investigation was to determine whether a shorter fasting period than the one historically employed for the charcoal meal test, could be used when measuring gastric emptying and intestinal transit within the same animal, and to ascertain whether the scientific outcome would be affected by this benefit to animal welfare. Rats and mice were fasted for 0, 3, 6 or 18 hours before the oral administration of vehicle or atropine. One hour later, the animals were orally administered a charcoal meal, then 20 minutes later, they were killed and the stomach and small intestine were removed. Intestinal transit time (the position of the charcoal front as a percentage of the total length of the small intestine) and relative gastric emptying (weight of stomach contents) were measured. Rats and mice fasted for six hours showed results for gastric emptying and intestinal transit which were similar to those obtained in animals fasted for 18 hours. Reducing the fasting period reduced the body weight loss in both species, and mice on shorter fasts could be group-housed, as hunger-induced fighting was lessened. Therefore, a fasting period of six hours was subsequently adopted for charcoal meal studies at our institution.

  19. 4. Photocopied June 1978 R.H. ROBERTSON, PENCIL AND CHARCOAL SKETCH, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. Photocopied June 1978 R.H. ROBERTSON, PENCIL AND CHARCOAL SKETCH, LAKE HENDERSON, FROM TAHAWUS CLUB BOAT DOCK. CA. 1914. SOURCE: ARTHUR CROCKER, PRESIDENT OF THE TAHAWUS CLUB. - Adirondack Iron & Steel Company, New Furnace, Hudson River, Tahawus, Essex County, NY

  20. Charcoal tattoo localization for differentiated thyroid cancer recurrence in the central compartment of the neck.

    PubMed

    Soprani, F; Bondi, F; Puccetti, M; Armaroli, V

    2012-04-01

    Recurrence of differentiated thyroid cancer can often require further surgical options. Reoperations may carry significant risk of surgical complications; additionally, as the anatomy is subverted, there is the possibility of leaving residual neoplasm. In order to avoid such problems during reoperation for differentiated thyroid cancer recurrence, we have introduced the technique of preoperative ultrasound-guided tattooing localization of the lymphatic structure to be removed with a 4% solution of active charcoal. Using ultrasound guidance, the lesion is identified and 0.5-2 ml of colloidal charcoal is injected near the lesion. The extraction of the needle is accompanied by injection at constant pressure of other charcoal as to leave a trace of colouring along the path of the needle up to the skin. The preoperative injection was well tolerated in all cases. In the last 5 years, we have used this technique in 13 patients with suspected recurrence in the central compartment (all from papillary carcinomas). Postoperative ultrasound and histological examination confirmed the removal of the lesion in all patients; in one case, the lesion was a parathyroid cyst. Complications were observed in two of 13 (15.4%) cases (one transitory hypoparathyroidism, and one transitory vocal cord paresis). Considering our experience, charcoal tattoo localization can be considered a safe, low-cost technique that is extremely useful for facilitating surgical procedures, and reduces the risk of iatrogenic damage.

  1. An Integrative Suicide Prevention Program for Visitor Charcoal Burning Suicide and Suicide Pact

    ERIC Educational Resources Information Center

    Wong, Paul W. C.; Liu, Patricia M. Y.; Chan, Wincy S. C.; Law, Y. W.; Law, Steven C. K.; Fu, King-Wa; Li, Hana S. H.; Tso, M. K.; Beautrais, Annette L.; Yip, Paul S. F.

    2009-01-01

    An integrative suicide prevention program was implemented to tackle an outbreak of visitor charcoal burning suicides in Cheung Chau, an island in Hong Kong, in 2002. This study evaluated the effectiveness of the program. The numbers of visitor suicides reduced from 37 deaths in the 51 months prior to program implementation to 6 deaths in the 42…

  2. Reconstructions of biomass burning from sediment-charcoal records to improve data-model comparisons

    NASA Astrophysics Data System (ADS)

    Marlon, Jennifer R.; Kelly, Ryan; Daniau, Anne-Laure; Vannière, Boris; Power, Mitchell J.; Bartlein, Patrick; Higuera, Philip; Blarquez, Olivier; Brewer, Simon; Brücher, Tim; Feurdean, Angelica; Gil Romera, Graciela; Iglesias, Virginia; Yoshi Maezumi, S.; Magi, Brian; Mustaphi, Colin J. Courtney; Zhihai, Tonishtan

    2016-06-01

    The location, timing, spatial extent, and frequency of wildfires are changing rapidly in many parts of the world, producing substantial impacts on ecosystems, people, and potentially climate. Paleofire records based on charcoal accumulation in sediments enable modern changes in biomass burning to be considered in their long-term context. Paleofire records also provide insights into the causes and impacts of past wildfires and emissions when analyzed in conjunction with other paleoenvironmental data and with fire models. Here we present new 1000-year and 22 000-year trends and gridded biomass burning reconstructions based on the Global Charcoal Database version 3 (GCDv3), which includes 736 charcoal records (57 more than in version 2). The new gridded reconstructions reveal the spatial patterns underlying the temporal trends in the data, allowing insights into likely controls on biomass burning at regional to global scales. In the most recent few decades, biomass burning has sharply increased in both hemispheres but especially in the north, where charcoal fluxes are now higher than at any other time during the past 22 000 years. We also discuss methodological issues relevant to data-model comparisons and identify areas for future research. Spatially gridded versions of the global data set from GCDv3 are provided to facilitate comparison with and validation of global fire simulations.

  3. An equilibrium-based model for measuring environmental radon using charcoal canisters.

    PubMed

    Lehnert, A L; Kearfott, K J

    2010-08-01

    Radon in indoor air is often measured using canisters of activated charcoal that function by adsorbing radon gas. The use of a diffusion barrier charcoal canister (DBCC) minimizes the effects of environmental humidity and extends the useful exposure time by several days. Many DBCC protocols model charcoal canisters as simple integrating detectors, which introduces errors due to the fact that radon uptake changes over the exposure period. Errors are compensated for by calculating a calibration factor that is nonlinear with respect to exposure time. This study involves the development and testing of an equilibrium-based model and corresponding measurement protocol that treats the charcoal canisters as a system coming into equilibrium with the surrounding radon environment. This model applies to both constant and temporally varying radon concentration situations, which was essential, as efforts are currently underway using a temporally varying radon chamber. It was found that the DBCCs equilibrate following the relationship E = (1 - e) where E is a measure of how close the DBCC is to equilibrium, t is exposure time, and q is the equilibration constant. This equilibration constant was empirically determined to be 0.019 h. The proposed model was tested in a blind test as well as compared with the currently accepted U.S. Environmental Protection Agency (U.S. EPA) model. Comparisons between the two methods showed a slight decrease in measurement error when using the equilibrium-based method as compared to the U.S. EPA method.

  4. Effect of supplementing activated charcoal on the intake of honey mesquite leaves by lambs

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A study was conducted to determine if intake of honey mesquite (Prosopis glandulosa Torr.) leaves by sheep could be increased by supplementing four levels of activated charcoal supplemental (0.0, 0.33, 0.67 and 1.00 g/kg of BW). Twenty wether lambs (36.6 ± 0.6 kg) were randomly assigned to the 4 tre...

  5. Effect of supplementing activated charcoal on the intake of honey mesquite leaves by lambs

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A study was conducted to determine if intake of honey mesquite (Prosopis glandulosa Torr.) leaves by sheep could be increased by supplementing activated charcoal at 0.0, 0.33, 0.67 or 1.00 g / kg of body weight. Twenty wether lambs (36.6 ± 0.6 kg) were randomly assigned to the 4 treatment levels. La...

  6. The Charcoal Trap: Miombo Woddlands and the Energy Demands of People

    NASA Astrophysics Data System (ADS)

    Kutsch, W. L.; Merbold, L.; Mukelabai, M. M.

    2012-04-01

    Miombo woodlands cover the transition zone between dry open savannas and moist forests in Southern Africa. They cover about 2.7 million km2 in southern Africa and provide many ecosystem services that support rural life, including medical products, wild foods, construction timber and fuel. In Zambia, as in many of its neighbouring countries, miombo woodlands are currently experiencing accelerating degradation and clearing, mostly with charcoal production as the initial driver. Domestic energy needs in the growing urban areas are largely satisfied by charcoal, which is less energy-efficient fuel on a tree-to-table basis than the firewood that is used in rural areas, but has a higher energy density and is thus cheaper to transport. This study uses data from inventories and from eddy covariance measurements of carbon exchange to characterize the impact of charcoal production on miombo woodlands. We address the following questions: (i) how much carbon is lost at local as well as at national scale and (ii) does forest degradation result in the loss of a carbon sink? On the basis of our data we (iii) estimate the per capita emissions through deforestation and forest degradation in Zambia and relate it to fossil fuel emissions. Furthermore, (iv) a rough estimate of the energy that is provided by charcoal production to private households at a national level is calculated and (v) options for alternative energy supply to private households are discussed.

  7. Intravenous theophylline poisoning and multiple-dose charcoal in an animal model.

    PubMed

    Kulig, K W; Bar-Or, D; Rumack, B H

    1987-08-01

    Large overdoses of IV theophylline (50 to 100 mg/kg) were administered to five canines on two separate occasions. On day one, with no charcoal administered, theophylline levels were serially obtained between ten minutes and 12 hours after infusion and the animals were recovered from anesthesia. Three days later the same dose of theophylline was administered, but then 50 g activated charcoal was placed through a nasogastric tube into the duodenum every hour for eight doses. In all five animals tested, activated charcoal significantly decreased the area under the serum concentration-time curve, decreased the half-life of elimination, and increased the clearance of theophylline. This effect on pharmacokinetics was not seen when the nasogastric tube was put into the stomach instead of the small bowel because the charcoal administered did not pass beyond the pylorus. In a separate experiment in which bile theophylline concentrations were measured, it was demonstrated that enhanced elimination was not from interruption of enterohepatic circulation of theophylline. This suggests that the demonstrated physiologic mechanism is that of gastrointestinal dialysis.

  8. Pharmacokinetics of quetiapine in overdose and the effect of activated charcoal.

    PubMed

    Isbister, G K; Friberg, L E; Hackett, L P; Duffull, S B

    2007-06-01

    The aim of the study was to investigate the pharmacokinetics of quetiapine overdose and the effect of charcoal. The data set included 204 concentration-time points from 54 quetiapine overdose events (median dose 2,700 mg (300-24,000 mg)). Charcoal was administered 0.5-6 h after 19 overdoses. A fully Bayesian methodology for population pharmacokinetic analysis was used and data were modelled using WinBUGS. Uncertainty in the dose history was considered in model building by estimating dose amount and dose time within a possible range. Inclusion of informative priors stabilized the model and population parameter values could be estimated well. A one-compartment model with first-order input and first-order elimination described the data. The final model included uncertainty in dose time. The median and interquartile range of the half-life for individual patients was 6.6 h (4.9-8.4 h). Charcoal was estimated to reduce fraction absorbed by 35%. Co-ingested CYP3A4 inhibitors appeared to decrease clearance and CYP3A4 inducers increase clearance. Charcoal administration may be beneficial after quetiapine overdose.

  9. Pyrolysis of blended animal manures to produce combustible gas and value-added charcoal adsorbent

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Blended swine solids, chicken litter, and rye grass were pyrolyzed using a skid-mounted sytem. Produced gas composition was analyzed for major hydrocarbons and S-containing compounds. Charcoal was analyzed for its surface functional groups, contact angles, HHV, and total element contents. Some of th...

  10. Carbon sequestration and fertility after centennial time scale incorporation of charcoal into soil

    NASA Astrophysics Data System (ADS)

    Criscuoli, Irene; Alberti, Giorgio; Baronti, Silvia; Favilli, Filippo; Martinez, Cristina; Calzolari, Costanza; Pusceddu, Emanuela; Rumpel, Cornelia; Viola, Roberto; Miglietta, Franco

    2014-05-01

    The addition of pyrogenic carbon (C) in the soil is considered a sustainable strategy to achieve direct C sequestration and potential reduction of non-CO2 greenhouse gas emissions. In this paper, we investigated the long term effects of charcoal addition on C sequestration and soil chemico-physical properties by studying a series of abandoned charcoal hearths in the Eastern Alps established in the XIX century. This natural setting can be seen as an analogue of a deliberate experiment with replications. Carbon sequestration was assessed indirectly by comparing the amount of C present in the hearths with the estimated amount of charcoal that was left on the soil after the carbonization. Approximately 80% of the C originally added to the soil via charcoal can still be found today, thus supporting the view that charcoal incorporation is an effective way to sequester atmospheric CO2. We also observed an improvement in the physical properties (hydrophobicity and bulk density) of charcoal hearth soils and an accumulation of nutrients compared to the adjacent soil without charcoal. Then, we focused on the morphological and physical characterization of several fragments, using scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray fluorescence (XRF). Such study enabled the identification of peculiar morphological features of tracheids, which were tentatively associated to a differential oxidation of the structures that were created during carbonization from lignine and cellulose. In order to assess the effect of soil-aging we compared the old-biochar with a modern one obtained from the same feedstock and with similar carbonization process. XRD and XRF analysis were performed on both old and modern biochar, in order to study the multiphase crystalline structure and chemical elements found. We observed mineralization and a fossilization of old biochar samples respect to the modern ones, with accumulation of several mineral oxides and a substantial presence of

  11. POLICIES AND GUIDELINES FOR THE TRAINING OF DENTAL AUXILIARIES.

    ERIC Educational Resources Information Center

    American Dental Association, Chicago, IL. Council on Dental Education.

    ALTHOUGH THE DENTAL PROFESSION NOW SEEKS SUPPORT FOR AUXILIARY TRAINING PROGRAMS FROM EDUCATIONAL INSTITUTES OTHER THAN DENTAL SCHOOLS, IT IS CONCERNED THAT TRAINING IN NONDENTAL SCHOOL SETTINGS SUCH AS JUNIOR COLLEGES, TECHNICAL INSTITUTES, UNIVERSITY EXTENSION PROGRAMS, AND POST-HIGH SCHOOL VOCATIONAL PROGRAMS PREVENTS TRAINEE EXPOSURE TO…

  12. Comparative assessment of selected PWR auxiliary feedwater system reliability analyses

    SciTech Connect

    Youngblood, R.; Fresco, A.; Papazoglou, I.A.; Tsao, J.

    1985-01-01

    This paper presents a sample of results obtained in reviewing utility submittals of Auxiliary Feedwater System reliability studies. These results are then used to illustrate a few general points regarding such studies. The submittals and reviews for operating license applications are quite significant in that they represent an application of probabilistic risk assessment techniques in the licensing process.

  13. Virtual Environment Training: Auxiliary Machinery Room (AMR) Watchstation Trainer.

    ERIC Educational Resources Information Center

    Hriber, Dennis C.; And Others

    1993-01-01

    Describes a project implemented at Newport News Shipbuilding that used Virtual Environment Training to improve the performance of submarine crewmen. Highlights include development of the Auxiliary Machine Room (AMR) Watchstation Trainer; Digital Video Interactive (DVI); screen layout; test design and evaluation; user reactions; authoring language;…

  14. The Development of a Proficiency Examination for Dental Auxiliaries.

    ERIC Educational Resources Information Center

    Kastrinos, William; Livingston, Samuel A.

    This report describes the development of a criterion-referenced proficiency examination for dental auxiliaries that consists of both written and performance tests in each of five areas: chairside assisting, patient education, diagnostic aids, therapeutics, and laboratory procedures. The content outlines of the tests are presented. The formation of…

  15. Green Propulsion Auxiliary Power Unit Demonstration at MSFC

    NASA Technical Reports Server (NTRS)

    Robinson, Joel W.

    2014-01-01

    MSFC has embarked on use of green propellant replacement of hydrazine for a variety of applications. This paper focused on activities for auxiliary power unit but MSFC is actively investigating use of green propellants for thruster applications. MSFC is interested in partnership with the international community to address the infusion of green propellant into greater use.

  16. 14 CFR 25.535 - Auxiliary float loads.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Auxiliary float loads. 25.535 Section 25.535 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... follows: EC28SE91.043 where— ρ=mass density of water (slugs/ft.2); V=volume of float (ft.2); C...

  17. 76 FR 22295 - National Poultry Improvement Plan and Auxiliary Provisions

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-21

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF AGRICULTURE Animal and Plant Health Inspection 9 CFR Part 145 RIN 0579-AD21 National Poultry Improvement Plan and Auxiliary Provisions Correction In rule document 2011-6539 appearing on pages 15791-15798 in the issue...

  18. Video versus lecture: effective alternatives for orthodontic auxiliary training.

    PubMed

    Chen, M S; Horrocks, E N; Evans, R D

    1998-08-01

    Many studies have compared the relative effectiveness of visually-aided lectures and videotapes, but methodological flaws have prevented definitive comparison of the techniques. This study assessed the relative effectiveness of the two approaches for orthodontic auxiliary training. This study was a prospective, randomised trial, conducted at the Eastman Dental Hospital and Institute. Two groups of 16 dental auxiliaries, selected at random, studied identification and positioning of orthodontic brackets: one group attended a lecture accompanied by slides and the other viewed a video. Subjects bonded brackets onto acrylic teeth and the results were assessed by computerised image analysis. The subjects completed a questionnaire on their attitudes to the respective teaching methods. Results were assessed for accuracy of bracket placement and variations in type of auxiliary. There was no significant difference between the teaching methods except for bracket positioning where video was slightly better (P < 0.05). There was no significant difference between the types of auxiliary. Generally, video teaching and lecturing were equally effective, with video achieving slightly better results. Both methods were effective at teaching bracket placement, and dental nurses and student hygienists proved equally adept at bracket positioning.

  19. Redox-mediated reactions of vinylferrocene: toward redox auxiliaries.

    PubMed

    Wiles, Alan A; Zhang, Xiaolu; Fitzpatrick, Brian; Long, De-Liang; Macgregor, Stuart A; Cooke, Graeme

    2016-05-01

    Chemical redox reactions have been exploited to transform unreactive vinylferrocene into a powerful dienophile for the Diels-Alder reaction and reactive substrate for thiol addition reactions upon conversion to its ferrocenium state. We have further investigated the ability of these reactions to facilitate redox-auxiliary-like reactivity by further hydrogenolyisis of the Diels-Alder adduct to the corresponding cyclopentane derivative.

  20. 17. DETAIL VIEW OF RIVITED ROOF AND INTERIOR OF AUXILIARY ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. DETAIL VIEW OF RIVITED ROOF AND INTERIOR OF AUXILIARY MACHINERY ROOM FOR 210' 9' J.A.L. WADDELL SPAN DRIVE VERTICAL LIFT BRIDGE - Central Railroad of New Jersey, Newark Bay Lift Bridge, Spanning Newark Bay, Newark, Essex County, NJ

  1. Development of Auxiliaries in Young Children Learning African American English

    ERIC Educational Resources Information Center

    Newkirk-Turner, Brandi L.; Oetting, Janna B.; Stockman, Ida J.

    2016-01-01

    Purpose: We examined language samples of young children learning African American English (AAE) to determine if and when their use of auxiliaries shows dialect-universal and dialect-specific effects. Method: The data were longitudinal language samples obtained from two children, ages 18 to 36 months, and three children, ages 33 to 51 months.…

  2. Search and Rescue. Auxiliary Operational Specialty Course. Student Text.

    ERIC Educational Resources Information Center

    Coast Guard, Washington, DC.

    This text, based on the National Search and Rescue (SAR) Plan, was prepared to provide a course of study on common procedures for SAR operations so that any basically qualified person in the U.S. Coast Guard Auxiliary can effectively accomplish a SAR mission and act as on-scene commander if required. There are 13 chapters: Introduction to Search…

  3. 14 CFR 25.535 - Auxiliary float loads.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... follows: EC28SE91.043 where— ρ=mass density of water (slugs/ft.2); V=volume of float (ft.2); C x... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.535 Auxiliary float loads. (a..., the prescribed water loads may be distributed over the float bottom to avoid excessive local...

  4. 49 CFR 193.2613 - Auxiliary power sources.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Auxiliary power sources. 193.2613 Section 193.2613 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY LIQUEFIED NATURAL GAS...

  5. 49 CFR 193.2613 - Auxiliary power sources.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Auxiliary power sources. 193.2613 Section 193.2613 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY LIQUEFIED NATURAL GAS...

  6. 49 CFR 193.2613 - Auxiliary power sources.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Auxiliary power sources. 193.2613 Section 193.2613 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY LIQUEFIED NATURAL GAS...

  7. 14 CFR 29.757 - Hull and auxiliary float strength.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... distributed water pressures over the hull and float bottom. Personnel and Cargo Accommodations ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Hull and auxiliary float strength. 29.757... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and...

  8. 14 CFR 29.757 - Hull and auxiliary float strength.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... distributed water pressures over the hull and float bottom. Personnel and Cargo Accommodations ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Hull and auxiliary float strength. 29.757... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and...

  9. 14 CFR 29.757 - Hull and auxiliary float strength.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... distributed water pressures over the hull and float bottom. Personnel and Cargo Accommodations ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and auxiliary float strength. 29.757... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and...

  10. 14 CFR 29.757 - Hull and auxiliary float strength.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... distributed water pressures over the hull and float bottom. Personnel and Cargo Accommodations ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Hull and auxiliary float strength. 29.757... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and...

  11. PBF Control Building auxiliary features, including fire hose house and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    PBF Control Building auxiliary features, including fire hose house and sewage system. Ebasco Services 1205 PER/PER-A-4. INEEL undex no. 760-0619-00-205-123024 - Idaho National Engineering Laboratory, SPERT-I & Power Burst Facility Area, Scoville, Butte County, ID

  12. A Junior College's Approach to Training Auxiliary Personnel in Education.

    ERIC Educational Resources Information Center

    Weisz, Vera C.

    Garland Junior College (Massachusetts) has developed a course of training for non-professional aides as auxiliary teaching personnel. As part of a trend toward liberalizing staffing patterns throughout the nation, it is expected to ease the shortage of teachers by relieving them of many routine classroom chores. A second purpose is to provide a…

  13. Tapered bed bioreactor

    DOEpatents

    Scott, Charles D.; Hancher, Charles W.

    1977-01-01

    A vertically oriented conically shaped column is used as a fluidized bed bioreactor wherein biologically catalyzed reactions are conducted in a continuous manner. The column utilizes a packing material a support having attached thereto a biologically active catalytic material.

  14. Chemical and Isotopic Thresholds in Charring: Implications for the Interpretation of Charcoal Mass and Isotopic Data

    NASA Astrophysics Data System (ADS)

    Pyle, L.; Hockaday, W. C.; Boutton, T. W.; Zygourakis, K.; Kinney, T.; Masiello, C. A.

    2014-12-01

    Charcoal plays a significant role in the long-term carbon cycle and its use as a soil amendment is becoming a viable carbon sequestration strategy (biochar). One challenge in this research area has been comparing results between studies in part due to the diversity of lab and field production conditions. Although the highest treatment temperature (HTT) is often used to describe pyrolysis conditions, several studies have shown that length of time at the highest temperature can also cause changes to the physicochemical qualities of charcoal and ignoring this effect may introduce inter-comparison problems. Addressing this issue becomes especially important in the discussion of optimizing biochar for soil remediation and carbon sequestration, and in discussions of charcoal use in reconstructing past fire regimes, as increasing time at temperature may cause changes in charcoal properties similar to the changes caused by increasing HTT. Here we introduce a formal definition of charring intensity (CI) to more accurately characterize pyrolysis, and we document variation in this property with pyrolysis temperature and reaction duration. We found two types of responses to CI: either a linear or a threshold relationship. We show that a threshold exists where %C, %N and δ15N begin exhibiting large changes, and this CI threshold co-occurred with an increase in charcoal aromaticity. Mass yield decreased linearly with charring intensity and carbon isotopes did not change from original biomass values in our controlled laboratory experiments. Analysis of these data shows that pyrolysis parameters should be defined in the literature as a combination of temperature and duration conditions, and that biomass that has undergone pyrolysis may be influencing soil organic nitrogen. Additionally, the lack of alteration in carbon isotopes across our matrix supports the efficacy of using pyrolyzed material for archaeological reconstructions.

  15. The Charcoal Trap: Miombo woodlands versus the energy needs of people

    NASA Astrophysics Data System (ADS)

    Merbold, Lutz; Maurice, Muchinda; Mukufute M, Mukelabai; J, Scholes Robert; Waldemar, Ziegler; L, Kutsch Werner

    2010-05-01

    Miombo woodlands cover the transition zone between the dry open savannas and the moist forests in Southern Africa and occupy the vast area of 2.7 Mio km2. These ecosystems are highly disturbed by deforestation, mostly for charcoal production. Charcoal has become the largest source to satisfy urban energy demands. Even though when charcoal is a less energy-efficient fuel compared to firewood but by having higher energy densities and thus being cheaper to transport. Over the last decades, charcoal production has become a full-time employment for migrant workers, resulting in very different and no longer sustainable deforestation patterns. Strategies to reduce the pressure on the miombo woodlands have to take aspects of employment and energy demand into account. The objectives of the study were to examine above- and belowground carbon losses from an intact miombo woodland (protected forest reserve) in comparison to a highly disturbed surrounding area due to charcoal production. Detection of changes in carbon concentrations and stocks were made possible by applying biomass- and soil inventories as well as the eddy-covariance method. These local results were up-scaled to countrywide estimates of carbon lost to the atmosphere by deforestation in addition to carbon losses fossil fuel combustion. The results show, that in the worst case scenario which does not assume any regeneration, a developing country as Zambia, can easily emit as much carbon per capita as a developed Western world country such as France, when deforestation is included in the national inventory (up to 9.1 t of CO2 per capita). However, regeneration is very probably when post-harvest disturbance is low. Further studies on miombo regeneration are highly demanded.

  16. Test Bed For Telerobots

    NASA Technical Reports Server (NTRS)

    Matijevic, Jacob R.; Zimmerman, Wayne F.; Dolinsky, Shlomo

    1990-01-01

    Assembly of electromechanical and electronic equipment (including computers) constitutes test bed for development of advanced robotic systems for remote manipulation. Combines features not found in commercial systems. Its architecture allows easy growth in complexity and level of automation. System national resource for validation of new telerobotic technology. Intended primarily for robots used in outer space, test bed adapted to development of advanced terrestrial telerobotic systems for handling radioactive materials, dangerous chemicals, and explosives.

  17. Bed exit alarms.

    PubMed

    2004-09-01

    Bed-exit alarms alert caregivers that a patient who should not get out of bed unassisted is doing so. These alarms can help reduce the likelihood of falls and can promote speedy assistance to patients who have already fallen. But as we described in our May 2004 Guidance Article on bed-exit alarms, they don't themselves prevent falls. They are only effective if used as part of an overall fall-prevention program and with a clear understanding of their limitations. This Evaluation examines the effectiveness of 16 bed-exit alarms from seven suppliers. Our ratings focus primarily on each product's reliability in detecting bed-exit events and alerting caregivers, its ability to minimize nuisance alarms (alarms that sound even though the patient isn't leaving the bed or that sound while a caregiver is helping the patient to leave the bed), and its resistance to deliberate or inadvertent tampering. Twelve of the products use pressure-sensor-activated alarms (mainly sensor pads placed on or under the mattress); three use a cord that can attach to the patient's garment, alarming if the cord is pulled loose from the control unit; and one is a position-sensitive alarm attached to a leg cuff. All the products reliably detect attempted or successful bed exits. But they vary greatly in how effectively they alert staff, minimize nuisance alarms, and resist tampering. Ease of use and battery performance also vary for many units. Of the pressure-sensor units, three are rated Preferred. Those units meet most of our criteria and have no significant disadvantages. Five of the other pressure-sensor products are Acceptable, and the remaining four are Not Recommended. All three cord-activated alarms are rated Acceptable, as is the patient-worn alarm.

  18. Bed rest and immunity

    NASA Astrophysics Data System (ADS)

    Sonnenfeld, Gerald; Aviles, Hernan; Butel, Janet S.; Shearer, William T.; Niesel, David; Pandya, Utpal; Allen, Christopher; Ochs, Hans D.; Blancher, Antoine; Abbal, Michel

    2007-02-01

    Space flight has been shown to result in altered immune responses. The current study was designed to investigate this possibility by using the bed rest model of some space flight conditions. A large number of women are included as subjects in the study. The hypothesis being tested is: 60 days head-down tilt bed rest of humans will affect the immune system and resistance to infection. Blood, urine and saliva samples will be obtained from bed rest subjects prior to, at intervals during, and after completion of 60 days of head-down tilt bed rest. Leukocyte blastogenesis, cytokine production and virus reactivation will be assessed. The ability of the subjects to respond appropriately to immunization with the neoantigen bacteriophage φX-174 will also be determined. Bed rest is being carried out at MEDES, Toulouse France, and the University of Texas Medical Branch, Galveston, TX. The studies to be carried out in France will also allow assessment of the effects of muscle/bone exercise and nutritional countermeasures on the immune system in addition to the effects of bed rest.

  19. Antifungal activity of nano and micro charcoal particle polymers against Paecilomyces variotii, Trichoderma virens and Chaetomium globosum.

    PubMed

    Yang, Hee Jin; Cha, Yun Jeong; Kim, Hern; Choi, Shin Sik

    2016-01-25

    This study investigates the antifungal activity of a polymer integrated with nano-porous charcoal particles against Paecilomyces variotii, Chaetomium globosum, Trichoderma virens, which are all filamentous fungi. The charcoal polymers were prepared by combining charcoal powders with plastic resin under a vacuum to form charcoal particle protrusions on the polymer surface. The mycelial growth of P. variotii and T. virens exhibited a reduction of 10 and 30%, respectively, after the conidia were pre-treated with charcoal polymers, and in particular, no mycelial growth was found in C. globosum during 5 days of culture. The adsorption of Ca(2+) into charcoal was suggested to inhibit growth due to the reduction in the flux of calcium ions (Ca(2+)) into the hyphae. In 5 h, about 15 mM of Ca(2+) were removed from CaCl2 solution with 0.2 g/mL of polymers, and the nano-sized pores of the charcoals on the polymer were responsible for the Ca(2+) adsorption. PMID:26277629

  20. Antifungal activity of nano and micro charcoal particle polymers against Paecilomyces variotii, Trichoderma virens and Chaetomium globosum.

    PubMed

    Yang, Hee Jin; Cha, Yun Jeong; Kim, Hern; Choi, Shin Sik

    2016-01-25

    This study investigates the antifungal activity of a polymer integrated with nano-porous charcoal particles against Paecilomyces variotii, Chaetomium globosum, Trichoderma virens, which are all filamentous fungi. The charcoal polymers were prepared by combining charcoal powders with plastic resin under a vacuum to form charcoal particle protrusions on the polymer surface. The mycelial growth of P. variotii and T. virens exhibited a reduction of 10 and 30%, respectively, after the conidia were pre-treated with charcoal polymers, and in particular, no mycelial growth was found in C. globosum during 5 days of culture. The adsorption of Ca(2+) into charcoal was suggested to inhibit growth due to the reduction in the flux of calcium ions (Ca(2+)) into the hyphae. In 5 h, about 15 mM of Ca(2+) were removed from CaCl2 solution with 0.2 g/mL of polymers, and the nano-sized pores of the charcoals on the polymer were responsible for the Ca(2+) adsorption.

  1. Auxiliary anatomical labels for joint segmentation and atlas registration

    NASA Astrophysics Data System (ADS)

    Gass, Tobias; Szekely, Gabor; Goksel, Orcun

    2014-03-01

    This paper studies improving joint segmentation and registration by introducing auxiliary labels for anatomy that has similar appearance to the target anatomy while not being part of that target. Such auxiliary labels help avoid false positive labelling of non-target anatomy by resolving ambiguity. A known registration of a segmented atlas can help identify where a target segmentation should lie. Conversely, segmentations of anatomy in two images can help them be better registered. Joint segmentation and registration is then a method that can leverage information from both registration and segmentation to help one another. It has received increasing attention recently in the literature. Often, merely a single organ of interest is labelled in the atlas. In the presense of other anatomical structures with similar appearance, this leads to ambiguity in intensity based segmentation; for example, when segmenting individual bones in CT images where other bones share the same intensity profile. To alleviate this problem, we introduce automatic generation of additional labels in atlas segmentations, by marking similar-appearance non-target anatomy with an auxiliary label. Information from the auxiliary-labeled atlas segmentation is then incorporated by using a novel coherence potential, which penalizes differences between the deformed atlas segmentation and the target segmentation estimate. We validated this on a joint segmentation-registration approach that iteratively alternates between registering an atlas and segmenting the target image to find a final anatomical segmentation. The results show that automatic auxiliary labelling outperforms the same approach using a single label atlasses, for both mandibular bone segmentation in 3D-CT and corpus callosum segmentation in 2D-MRI.

  2. Charcoal records reveal past occurrences of disturbances in the forests of the Kisangani region, Democratic Republic of the Congo

    NASA Astrophysics Data System (ADS)

    Tshibamba Mukendi, John; Hubau, Wannes; Ntahobavuka, Honorine; Boyemba Bosela, Faustin; De Cannière, Charles; Beeckman, Hans

    2014-05-01

    Past disturbances have modified local density, structure and floristic composition of Central African rainforests. As such, these perturbations represent a driving force for forest dynamics and they were presumably at the origin of present-day forest mosaics. One of the most prominent disturbances within the forest is fire, leaving behind charcoal as a witness of past forest dynamics. Quantification and identification of ancient charcoal fragments found in soil layers (= pedoanthracology) allows a detailed reconstruction of forest history, including the possible occurrence of past perturbations. The primary objective of this study is to present palaeoenvironmental evidence for the existence of past disturbances in the forests of the Kisangani region (Democratic Republic of the Congo) using a pedoanthracological approach. We quantified and identified charcoal fragments from pedoanthracological excavations in the Yangambi, Yoko, Masako and Kole forest regions. Charcoal sampling was conducted in pit intervals of 10 cm, whereby pottery fragments were also registered and quantified. Floristic identifications were conducted using former protocols based on wood anatomy, which is largely preserved after charcoalification. 14 excavations were conducted and charcoal was found in most pit intervals. Specifically, 52 out of 56 sampled intervals from the Yangambi forest contained charcoal, along with 47 pit intervals from the Yoko forest reserve, 34 pit intervals from the Masako forest and 16 from the Kole forest. Highest specific anthracomasses were recorded in Yoko (167 mg charcoal per kg soil), followed by Yangambi (133 mg/kg), Masako (71,89 mg/kg) and finally Kole (42,4 mg/kg). Charcoal identifications point at a manifest presence of the family of Fabaceae (Caesalpinioideae). This family is characteristic for the tropical humid rainforest. The presence of charcoal fragments from these taxa, associated with pottery sherds on different depths within the profiles, suggests

  3. Does Management Matter?: Using MISR to Assess the Effects of Charcoal Production and Management on Woodland Regeneration

    NASA Astrophysics Data System (ADS)

    Wurster, K.

    2008-12-01

    In much of Sub-Saharan Africa, more than 75 percent of a rapidly growing urban population depends on charcoal as their primary source of energy for cooking. The high demand for charcoal has led many to believe that charcoal harvesting catalyzes widespread deforestation. The Senegalese government and international donors have initiated projects within protected areas to combat deforestation and created land management plans to sustainably harvest charcoal. To date, the effects of forest management techniques on forest sustainability are still in question. This research uses a multiphase approach integrating satellite analysis with field surveys to assess the effect of varying forest management strategies on forest regeneration and sustainability after charcoal harvesting. Phase I involved testing the Multiangle Imaging SpectroRadiometer (MISR) satellites capability in detecting structural changes in vegetative cover caused by charcoal harvesting and production. Analysis of the MISR derived k(red) parameter showed MISR can consistently differentiate between forest cover types and successfully differentiates between sites at pre- and post-charcoal harvest stages. Phase II conducted forestry and social surveys comparing and contrasting local effects of land management, land use, and charcoal production on forest regeneration. Phase III uses the local surveys to validate and train the regional remote sensing data to assess the effectiveness of land management in promoting forest regeneration and sustainability after charcoal harvesting. Combining detailed local knowledge with the regional capabilities of MISR provide valuable insight into the factors that control woodland regeneration and sustainability. Preliminary results from phases II and III indicate that both field and remotely sensed variations in forest cover, tree regeneration, and land use change does not vary when compared against land management type. Final results will provide managers with additional

  4. Solar-driven coal gasification in a thermally irradiated packed-bed reactor

    SciTech Connect

    Nicolas Piatkowski; Aldo Steinfeld

    2008-05-15

    Coal gasification for high-quality synthesis gas production is considered using concentrated solar energy as the source of high-temperature process heat. The solar reactor consists of two cavities separated by a radiant emitter plate, with the upper one serving as the solar absorber and the lower one containing the reacting packed bed that shrinks as the reaction progresses. A 5 kW prototype reactor with an 8 cm depth, 14.3 cm diameter cylindrical bed was fabricated and tested in a high-flux solar furnace, subjected to solar flux concentrations up to 2600 suns and packed-bed temperatures up to 1440 K. The reactor is modeled by formulating the 1D unsteady energy conservation equation that couples conductive-radiative heat transfer with the reaction kinetics and solving it by the finite volume technique for a transient shrinking domain. The overall reaction rate was determined experimentally by thermogravimetry, while the effective thermal conductivity was determined experimentally in a radial heat flow oven. Model validation was accomplished in terms of bed temperatures, gasified mass, and bed shrink rates measured in solar experiments conducted with beech charcoal. Heat transfer through the bed proved to be the rate-controlling mechanism, indicating an ablation regime. 31 refs., 18 figs.

  5. Control of bed height in a fluidized bed gasification system

    DOEpatents

    Mehta, Gautam I.; Rogers, Lynn M.

    1983-12-20

    In a fluidized bed apparatus a method for controlling the height of the fdized bed, taking into account variations in the density of the bed. The method comprises taking simultaneous differential pressure measurements at different vertical elevations within the vessel, averaging the differential pressures, determining an average fluidized bed density, then periodically calculating a weighting factor. The weighting factor is used in the determination of the actual bed height which is used in controlling the fluidizing means.

  6. Macro-particle charcoal C content following prescribed burning in a mixed-conifer forest, Sierra Nevada, California.

    PubMed

    Wiechmann, Morgan L; Hurteau, Matthew D; Kaye, Jason P; Miesel, Jessica R

    2015-01-01

    Fire suppression and changing climate have resulted in increased large wildfire frequency and severity in the western United States, causing carbon cycle impacts. Forest thinning and prescribed burning reduce high-severity fire risk, but require removal of biomass and emissions of carbon from burning. During each fire a fraction of the burning vegetation and soil organic matter is converted into charcoal, a relatively stable carbon form. We sought to quantify the effects of pre-fire fuel load and type on charcoal carbon produced by biomass combusted in a prescribed burn under different thinning treatments and to identify more easily measured predictors of charcoal carbon mass in a historically frequent-fire mixed-conifer forest. We hypothesized that charcoal carbon produced from coarse woody debris (CWD) during prescribed burning would be greater than that produced from fine woody debris (FWD). We visually quantified post-treatment charcoal carbon content in the O-horizon and the A-horizon beneath CWD (> 30 cm diameter) and up to 60 cm from CWD that was present prior to treatment. We found no difference in the size of charcoal carbon pools from CWD (treatment means ranged from 0.3-2.0 g m-2 of A-horizon and 0.0-1.7 g m-2 of O-horizon charcoal) and FWD (treatment means ranged from 0.2-1.7 g m-2 of A-horizon and 0.0-1.5 g m-2 of O-horizon charcoal). We also compared treatments and found that the burn-only, understory-thin and burn, and overstory-thin and burn treatments had significantly more charcoal carbon than the control. Charcoal carbon represented 0.29% of total ecosystem carbon. We found that char mass on CWD was an important predictor of charcoal carbon mass, but only explained 18-35% of the variation. Our results help improve our understanding of the effects forest restoration treatments have on ecosystem carbon by providing additional information about charcoal carbon content.

  7. Macro-particle charcoal C content following prescribed burning in a mixed-conifer forest, Sierra Nevada, California.

    PubMed

    Wiechmann, Morgan L; Hurteau, Matthew D; Kaye, Jason P; Miesel, Jessica R

    2015-01-01

    Fire suppression and changing climate have resulted in increased large wildfire frequency and severity in the western United States, causing carbon cycle impacts. Forest thinning and prescribed burning reduce high-severity fire risk, but require removal of biomass and emissions of carbon from burning. During each fire a fraction of the burning vegetation and soil organic matter is converted into charcoal, a relatively stable carbon form. We sought to quantify the effects of pre-fire fuel load and type on charcoal carbon produced by biomass combusted in a prescribed burn under different thinning treatments and to identify more easily measured predictors of charcoal carbon mass in a historically frequent-fire mixed-conifer forest. We hypothesized that charcoal carbon produced from coarse woody debris (CWD) during prescribed burning would be greater than that produced from fine woody debris (FWD). We visually quantified post-treatment charcoal carbon content in the O-horizon and the A-horizon beneath CWD (> 30 cm diameter) and up to 60 cm from CWD that was present prior to treatment. We found no difference in the size of charcoal carbon pools from CWD (treatment means ranged from 0.3-2.0 g m-2 of A-horizon and 0.0-1.7 g m-2 of O-horizon charcoal) and FWD (treatment means ranged from 0.2-1.7 g m-2 of A-horizon and 0.0-1.5 g m-2 of O-horizon charcoal). We also compared treatments and found that the burn-only, understory-thin and burn, and overstory-thin and burn treatments had significantly more charcoal carbon than the control. Charcoal carbon represented 0.29% of total ecosystem carbon. We found that char mass on CWD was an important predictor of charcoal carbon mass, but only explained 18-35% of the variation. Our results help improve our understanding of the effects forest restoration treatments have on ecosystem carbon by providing additional information about charcoal carbon content. PMID:26258533

  8. Continued studies of co-pumping of deuterium and helium on a single, 4K activated charcoal panel

    SciTech Connect

    Walthers, C.R.; Jenkins, E.M. ); Batzer, T.H. ); Sedgley, D.W. ); Konishi, S.; Ohira, S.; Naruse, Y. )

    1990-09-01

    The short program undertaken in 1989 to evaluate the feasibility of co-pumping deuterium and tritium (DT) and helium on a charcoal sorbent showed that the charcoal will indeed simultaneously pump the gases. Of interest also was the fact that the total accumulation of helium (capacity) was virtually identical in constant throughput runs in which the D{sub 2}/He ratio was changed between runs. The test program described in this paper undertaken to evaluate further the co-pumping capabilities of the charcoal sorbent.

  9. The environmental impact on air quality and exposure to carbon monoxide from charcoal production in southern Brazil.

    PubMed

    Gomes, Gabriel Meneghetti Faé; Encarnação, Fábio

    2012-07-01

    Black wattle silviculture is an important activity in southern Brazil. Much of the wood is used in the production of charcoal and the pyrolysis products impacts on air quality. This paper estimates the level of atmospheric contamination from the production of charcoal in one region of Brazil. We describe a low-cost charcoal kiln that can capture condensable gases and we estimate the levels of exposure of kiln workers to carbon monoxide. The latter results indicated that exposure to carbon monoxide can be reduced from an average of 950 ppm to 907 ppm and the mass of gases reduced by 16.8%. PMID:22541721

  10. Macro-Particle Charcoal C Content following Prescribed Burning in a Mixed-Conifer Forest, Sierra Nevada, California

    PubMed Central

    Wiechmann, Morgan L.; Hurteau, Matthew D.; Kaye, Jason P.; Miesel, Jessica R.

    2015-01-01

    Fire suppression and changing climate have resulted in increased large wildfire frequency and severity in the western United States, causing carbon cycle impacts. Forest thinning and prescribed burning reduce high-severity fire risk, but require removal of biomass and emissions of carbon from burning. During each fire a fraction of the burning vegetation and soil organic matter is converted into charcoal, a relatively stable carbon form. We sought to quantify the effects of pre-fire fuel load and type on charcoal carbon produced by biomass combusted in a prescribed burn under different thinning treatments and to identify more easily measured predictors of charcoal carbon mass in a historically frequent-fire mixed-conifer forest. We hypothesized that charcoal carbon produced from coarse woody debris (CWD) during prescribed burning would be greater than that produced from fine woody debris (FWD). We visually quantified post-treatment charcoal carbon content in the O-horizon and the A-horizon beneath CWD (> 30 cm diameter) and up to 60 cm from CWD that was present prior to treatment. We found no difference in the size of charcoal carbon pools from CWD (treatment means ranged from 0.3–2.0 g m-2 of A-horizon and 0.0–1.7 g m-2 of O-horizon charcoal) and FWD (treatment means ranged from 0.2–1.7 g m-2 of A-horizon and 0.0–1.5 g m-2 of O-horizon charcoal). We also compared treatments and found that the burn-only, understory-thin and burn, and overstory-thin and burn treatments had significantly more charcoal carbon than the control. Charcoal carbon represented 0.29% of total ecosystem carbon. We found that char mass on CWD was an important predictor of charcoal carbon mass, but only explained 18–35% of the variation. Our results help improve our understanding of the effects forest restoration treatments have on ecosystem carbon by providing additional information about charcoal carbon content. PMID:26258533

  11. The influence of production conditions, starting material and deposition environment on charcoal alteration in a tropical biome.

    NASA Astrophysics Data System (ADS)

    Ascough, Philippa; Bird, Michael; Meredith, Will; Large, David; Snape, Colin; Manion, Corinne

    2014-05-01

    Natural and anthropogenic burning events are a key link in the global carbon cycle, substantially influencing atmospheric CO2 levels, and consuming c.8700 teragrams yr-1 of dry biomass [1,2,3]. An important result of this process is charcoal, when lignocellulosic structures in biomass (e.g. wood) are converted to aromatic domains with high chemical stability. Charcoal is therefore not readily re-oxidized to CO2, with estimates of 5-7 ky for the half-life of charcoal carbon in soils [3,4]. Charcoal's high carbon content coupled with high environmental resistance has led to the concept of biochar as a valuable means of global carbon sequestration, capable of carbon offsets comparable to annual anthropogenic fuel emissions [5,6,7]. Charcoal is not, however, an environmentally inert substance, and at least some components of charcoal are susceptible to alteration in depositional environments. Despite the importance of charcoal in global carbon cycling, the mechanisms by which charcoal is altered in the environment remain, as yet, poorly understood. This fact limits our ability to properly incorporate both natural environmental charcoal and biochar into global carbon budgets. This study aimed to improve understanding of charcoal alteration in the environment by examining the influence of production conditions, starting material and deposition environment on the physical and chemical characteristics of charcoal at a field site in the Daintree rainforest. These factors have been identified as critical in determining the dynamics of charcoal in depositional environments [8,9] and climatic conditions at the field site (in Tropical Queensland, Australia) are likely to result in extensive alteration of charcoal. Charcoal from wood (Nothofagus spp.), algae (Enteromorpha spp.), and sugarcane (Saccharum spp.) biomass was produced at temperatures over 300-500°C and exposed to conditions of varying pH and vegetation cover. The effect of these variables on charcoal chemistry

  12. BE, DO, and Modal Auxiliaries of 3-Year-Old African American English Speakers

    ERIC Educational Resources Information Center

    Newkirk-Turner, Brandi L.; Oetting, Janna B.; Stockman, Ida J.

    2014-01-01

    Purpose: This study examined African American English--speaking children's use of BE, DO, and modal auxiliaries. Method: The data were based on language samples obtained from 48 three-year-olds. Analyses examined rates of marking by auxiliary type, auxiliary surface form, succeeding element, and syntactic construction and by a number of child…

  13. 30 CFR 57.8534 - Shutdown or failure of auxiliary fans.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Shutdown or failure of auxiliary fans. 57.8534... Ventilation Underground Only § 57.8534 Shutdown or failure of auxiliary fans. (a) Auxiliary fans installed and... fan maintenance or fan adjustments where air quality is maintained in compliance with the...

  14. 30 CFR 57.22209 - Auxiliary fans (I-C mines).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22209 Auxiliary fans (I-C mines). Electric auxiliary fans shall be approved by MSHA under the applicable requirements of 30 CFR part 18... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Auxiliary fans (I-C mines). 57.22209 Section...

  15. 30 CFR 57.22209 - Auxiliary fans (I-C mines).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22209 Auxiliary fans (I-C mines). Electric auxiliary fans shall be approved by MSHA under the applicable requirements of 30 CFR part 18... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Auxiliary fans (I-C mines). 57.22209 Section...

  16. 30 CFR 57.22209 - Auxiliary fans (I-C mines).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22209 Auxiliary fans (I-C mines). Electric auxiliary fans shall be approved by MSHA under the applicable requirements of 30 CFR part 18... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Auxiliary fans (I-C mines). 57.22209 Section...

  17. 30 CFR 57.8534 - Shutdown or failure of auxiliary fans.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Shutdown or failure of auxiliary fans. 57.8534... Ventilation Underground Only § 57.8534 Shutdown or failure of auxiliary fans. (a) Auxiliary fans installed and... fan maintenance or fan adjustments where air quality is maintained in compliance with the...

  18. 30 CFR 57.8534 - Shutdown or failure of auxiliary fans.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Shutdown or failure of auxiliary fans. 57.8534... Ventilation Underground Only § 57.8534 Shutdown or failure of auxiliary fans. (a) Auxiliary fans installed and... fan maintenance or fan adjustments where air quality is maintained in compliance with the...

  19. 30 CFR 57.8534 - Shutdown or failure of auxiliary fans.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Shutdown or failure of auxiliary fans. 57.8534... Ventilation Underground Only § 57.8534 Shutdown or failure of auxiliary fans. (a) Auxiliary fans installed and... fan maintenance or fan adjustments where air quality is maintained in compliance with the...

  20. 30 CFR 57.22209 - Auxiliary fans (I-C mines).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22209 Auxiliary fans (I-C mines). Electric auxiliary fans shall be approved by MSHA under the applicable requirements of 30 CFR part 18... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Auxiliary fans (I-C mines). 57.22209 Section...

  1. 30 CFR 57.8534 - Shutdown or failure of auxiliary fans.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Shutdown or failure of auxiliary fans. 57.8534... Ventilation Underground Only § 57.8534 Shutdown or failure of auxiliary fans. (a) Auxiliary fans installed and... fan maintenance or fan adjustments where air quality is maintained in compliance with the...

  2. 30 CFR 57.22209 - Auxiliary fans (I-C mines).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22209 Auxiliary fans (I-C mines). Electric auxiliary fans shall be approved by MSHA under the applicable requirements of 30 CFR part 18... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Auxiliary fans (I-C mines). 57.22209 Section...

  3. 47 CFR 74.601 - Classes of TV broadcast auxiliary stations.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 4 2014-10-01 2014-10-01 false Classes of TV broadcast auxiliary stations. 74... Television Broadcast Auxiliary Stations § 74.601 Classes of TV broadcast auxiliary stations. (a) TV pickup stations. A land mobile station used for the transmission of TV program material and related...

  4. 47 CFR 74.601 - Classes of TV broadcast auxiliary stations.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 4 2013-10-01 2013-10-01 false Classes of TV broadcast auxiliary stations. 74... Television Broadcast Auxiliary Stations § 74.601 Classes of TV broadcast auxiliary stations. (a) TV pickup stations. A land mobile station used for the transmission of TV program material and related...

  5. 47 CFR 74.601 - Classes of TV broadcast auxiliary stations.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 4 2012-10-01 2012-10-01 false Classes of TV broadcast auxiliary stations. 74... Television Broadcast Auxiliary Stations § 74.601 Classes of TV broadcast auxiliary stations. (a) TV pickup stations. A land mobile station used for the transmission of TV program material and related...

  6. Predicting distributions of charcoal in Amazonian soils: approaches from earth and space

    NASA Astrophysics Data System (ADS)

    McMichael, C.; Palace, M. W.; Bush, M. B.; Braswell, R.; Hagen, S. C.; Czarnecki, C.; Neves, E.; Raczka, M.

    2011-12-01

    The direct linkage between fire and human activity in Amazonian rainforests is evidenced in both remote sensing datasets and field-based research. Paleoecological and archaeological data suggest the synergy has persisted millennia, and that human populations may have equaled modern numbers before European contact. Pre-Columbian people used fire to clear forests, but also combined charcoal with other materials to form Amazonian Black Earths (ABE), a nutrient rich anthrosol believed to be capable of sustaining large-scale permanent societies in such nutrient-poor tropical settings. The majority of impacted sites are found on bluffs overlooking Amazonian rivers, which are considered 'preferred' settings. Here, we examine predictions about preferred settings and the distributions of charcoal resulting from pre-Columbian human activity in western and central Amazonia using proxies from both earth and space. Soil sampling, stratified based on distance from river and forest seasonality, was used to determine whether preferred locations had higher probabilities of impacts. We analyzed more than 351 soil cores for ABE and macroscopic charcoal (> 500 μm) in the upper 20 cm of soil (representing modern fires), and in soils > 20 cm depth (representing historic fires). ABE was absent from all sites, but logistic regressions indicated that probabilities of finding soil charcoal significantly decreased as distance from river increased in aseasonal forests. However, in more seasonal forests, the probability of finding charcoal was increased, although distance from river was not a significant factor. Alternately, the location of ABE and charcoal mainly along major rivers may be an artifact of sampling. To look at distributions of ABE across broad spatial scales that may not be accessible from the ground, we used Hyperion satellite images to detect canopy chemistry differences resulting from various soil nutrients (i.e. soil enrichment occurring at ABE sites). Our initial findings

  7. Cooling of debris beds

    SciTech Connect

    Barleon, L.; Thomauske, K.; Werie, H.

    1984-04-01

    The dependence of the dryout heat flux for volume-heated particulate beds on bed height (less than or equal to40 cm), particle diameter (0.06 to 16 mm), stratification and boundary conditions (saturated and subcooled liquid, adiabatic and cooled bottom and sidewalls) has been determined for water and Freon-113. Channel penetration through subcooled layers and ''downward boiling'' due to capillarity effects have been observed. Different types of bed disturbances have been identified, and their effect on dryout has been studied. Using existing theoretical models, which have been verified by the experiments, the upper limit of the thermal load on support structures has been calculated as a function of the particle size and bottom temperature for reactor accident conditions (Pu/U-oxide particles in sodium).

  8. Treatment bed microbiological control

    NASA Technical Reports Server (NTRS)

    Janauer, Gilbert E.; Fitzpatrick, Timothy W.; Kril, Michael B.; Wilber, Georgia A.; Sauer, Richard L.

    1987-01-01

    The effects of microbial fouling on treatment bed (TB) performance are being studied. Fouling of activated carbon (AC) and ion exchange resins (IEX) by live and devitalized bacteria can cause decreased capacity for selected sorbates with AC and IEX TB. More data are needed on organic species removal in the trace region of solute sorption isotherms. TB colonization was prevented by nonclassical chemical disinfectant compositions (quaternary ammonium resins) applied in suitable configurations. Recently, the protection of carbon beds via direct disinfectant impregnation has shown promise. Effects (of impregnation) upon bed sorption/removal characteristics are to be studied with representative contaminants. The potential need to remove solutes added or produced during water disinfection and/or TB microbiological control must be investigated.

  9. Component Data Base for Space Station Resistojet Auxiliary Propulsion

    NASA Technical Reports Server (NTRS)

    Bader, Clayton H.

    1988-01-01

    The resistojet was baselined for Space Station auxiliary propulsion because of its operational versatility, efficiency, and durability. This report was conceived as a guide to designers and planners of the Space Station auxiliary propulsion system. It is directed to the low thrust resistojet concept, though it should have application to other station concepts or systems such as the Environmental Control and Life Support System (ECLSS), Manufacturing and Technology Laboratory (MTL), and the Waste Fluid Management System (WFMS). The information will likely be quite useful in the same capacity for other non-Space Station systems including satellite, freeflyers, explorers, and maneuvering vehicles. The report is a catalog of the most useful information for the most significant feed system components and is organized for the greatest convenience of the user.

  10. [The design of bionic left ventricular auxiliary pump].

    PubMed

    Jin, Henglin; Hu, Xiaobing; Du, Lei

    2015-01-01

    This paper reports a novel design of bionic left ventricular auxiliary pump, and the characteristic is that elastic diaphragm of pump driven by hydraulic, having smooth, reliable blood supply, can prevent blood clots, can use the flow sensor, pressure sensor detection showing the blood pressure and blood volume at the inlet and outlet of the pump. The pump can go with heart rate synchronization or asynchronous auxiliary by the R wave of human body's ECG. The design goal is realization of bionic throb. Through the animal experiment, the blood pressure waveforms are close to expectations, stable flow can stroke according to the set value, which prove that the pump can meet the requirement for heart disease patients for bionic left ventricular assistant.

  11. Removal of microcystin-LR from drinking water using a bamboo-based charcoal adsorbent modified with chitosan.

    PubMed

    Zhang, Hangjun; Zhu, Guoying; Jia, Xiuying; Ding, Ying; Zhang, Mi; Gao, Qing; Hu, Ciming; Xu, Shuying

    2011-01-01

    A new kind of low-cost syntactic adsorbent from bamboo charcoal and chitosan was developed for the removal of microcystin-LR from drinking water. Removal efficiency was higher for the syntactic adsorbent when the amount of bamboo charcoal was increased. The optimum dose ratio of bamboo charcoal to chitosan was 6:4, and the optimum amount was 15 mg/L; equilibrium time was 6 hr. The adsorption isotherm was non-linear and could be simulated by the Freundlich model (R2 = 0.9337). Adsorption efficiency was strongly affected by pH and natural organic matter (NOM). Removal efficiency was 16% higher at pH 3 than at pH 9. Efficiency rate was reduced by 15% with 25 mg/L NOM (UV254 = 0.089 cm(-1)) in drinking water. This study demonstrated that the bamboo charcoal modified with chitosan can effectively remove microcystin-LR from drinking water.

  12. Fluidized bed coal desulfurization

    NASA Technical Reports Server (NTRS)

    Ravindram, M.

    1983-01-01

    Laboratory scale experiments were conducted on two high volatile bituminous coals in a bench scale batch fluidized bed reactor. Chemical pretreatment and posttreatment of coals were tried as a means of enhancing desulfurization. Sequential chlorination and dechlorination cum hydrodesulfurization under modest conditions relative to the water slurry process were found to result in substantial sulfur reductions of about 80%. Sulfur forms as well as proximate and ultimate analyses of the processed coals are included. These studies indicate that a fluidized bed reactor process has considerable potential for being developed into a simple and economic process for coal desulfurization.

  13. Staged fluidized bed

    DOEpatents

    Mallon, R.G.

    1983-05-13

    The invention relates to oil shale retorting and more particularly to staged fluidized bed oil shale retorting. Method and apparatus are disclosed for narrowing the distribution of residence times of any size particle and equalizing the residence times of large and small particles in fluidized beds. Particles are moved up one fluidized column and down a second fluidized column with the relative heights selected to equalize residence times of large and small particles. Additional pairs of columns are staged to narrow the distribution of residence times and provide complete processing of the material.

  14. Space shuttle auxiliary propulsion system design study. Executive summary

    NASA Technical Reports Server (NTRS)

    Kelly, P. J.; Schweickert, T. F.

    1972-01-01

    The development and characteristics of an auxiliary propulsion system for space shuttle applications are presented. The system design data necessary for selection of preferred system concepts and the requirements for complementing component design and test programs are analyzed. The use of cryogenic oxygen and hydrogen as a propellant combination is explained on the basis of high vehicle impulse requirements, safety factors, reuse, and logistics considerations. The final configurations for the alternate propellant system, with primary emphasis on earth storable propellants is described.

  15. Parallel auxiliary space AMG for definite Maxwell problems

    SciTech Connect

    Kolev, T V; Vassilevski, P S

    2007-02-16

    Motivated by the needs of large multi-physics simulation codes, we are interested in algebraic solvers for the linear systems arising in time-domain electromagnetic simulations. Our focus is on finite element discretization, and we are developing scalable parallel preconditioners which employ only fine-grid information, similar to algebraic multigrid (AMG) for diffusion problems. In the last few years, the search for efficient algebraic preconditioners for H(curl) bilinear forms has intensified. The attempts to directly construct AMG methods had some success, see [12, 1, 7]. Exploiting available multilevel methods on auxiliary mesh for the same bilinear form led to efficient auxiliary mesh preconditioners to unstructured problems as shown in [4, 8]. A computationally more attractive approach was recently proposed by Hiptmair and Xu [5]. In contrast to the auxiliary mesh idea, the method in [5] uses a nodal H{sup 1}-conforming auxiliary space on the same mesh. This significantly simplifies the computation of the corresponding interpolation operator. In the present talk, we consider several options for constructing unstructured mesh AMG preconditioners for H(curl) problems and report a summary of computational results from [10, 9]. Our approach is slightly different than the one from [5], since we apply AMG directly to variationally constructed coarse-grid operators, and therefore no additional Poisson matrices are needed on input. We also consider variable coefficient problems, including some that lead to a singular matrix. Both type of problems are of great practical importance and are not covered by the theory of [5].

  16. Electrical Auxiliary Power Unit (EAPU) Corona Design Guideline. Revised

    NASA Technical Reports Server (NTRS)

    Hall, David K.; Kirkici, Hulya; Schweickart, Dan L.; Dunbar, William; Hillard, Barry

    2000-01-01

    This document is the result of a collaborative effort between NASA's Johnson Space Center, Marshall Space Flight Center, Glenn Research Center, and the United States Air Force Research Laboratory at Wright Patterson AFB in support of the Space Shuttle Orbiter Upgrades Program, specifically the Electric Auxiliary Power Unit Program. This document is intended as a guideline for design applications for corona and partial discharge avoidance and is not a requirements specification instrument.

  17. The addition of charcoals to broiler diets did not alter the recovery of Salmonella Typhimurium during grow-out.

    PubMed

    Wilson, K M; Bourassa, D V; Davis, A J; Freeman, M E; Buhr, R J

    2016-03-01

    Two experiments evaluated prebiotics added to feed on the recovery of Salmonella in broilers during grow-out and processing. In Experiment 1, "seeder" chicks were inoculated with Salmonella Typhimurium and placed with penmates. Treatments were: basal control diet, added 0.3% bamboo charcoal, 0.6% bamboo charcoal, or 0.12% Aromabiotic (medium chain fatty acids). The ceca from seeders and penmates were sampled to confirm Salmonella colonization at 3, 4, and 6 wk, and pen litter was sampled weekly. At 3 wk, charcoal fed chicks had significantly lower cecal recovery (37% lower) of Salmonella via direct plating but no differences at wk 4 or 6. At 6 wk, broilers fed Aromabiotic had no recovery of Salmonella from ceca with direct plating and significantly, 18%, lower recovery with enrichment. In Experiment 2, the treatments were: basal control diet, added 0.3% bamboo charcoal, 0.3% activated bamboo charcoal, or 0.3% pine charcoal. At placement, 2 seeders were challenged with Salmonella and commingled with penmates and ceca sampled at 1 and 2 wk, and ceca from 5 penmates/pen at 3 to 6 wk. Weekly, the pH of the crop and duodenum was measured from 1 penmate/pen and the litter surface sampled. At the end of grow-out broilers were processed. Results showed that penmates had colonized at 1 and 2 wk. Cecal Salmonella showed no differences except at 4 wk, when activated bamboo charcoal had a 18% lower recovery of Salmonella (enrichment) compared to the control (88%). Similar to Experiment 1, the recovery of Salmonella from the litter was not significantly different among treatments, however an overall decrease in recovery by 4 wk with direct plating reoccurred. The pH of the duodenum and the crop were not different among treatments. Crop pH (6.0) for all treatments were significantly higher at wk 1 compared to wk 2 to 6. Charcoals had minimal effect on Salmonella recovery in the ceca, but following defeathering, broilers fed charcoals had significantly lower Salmonella

  18. Anthropogenic Charcoal Deposits: Analogues for the Long-Term Functioning and Stability of Biochar in European Soils?

    NASA Astrophysics Data System (ADS)

    Mugford, Ian; Street-Perrot, Alayne; Santín, Cristina; Denman, Huw

    2014-05-01

    Anthropogenic charcoal deposits, characterised by thick charcoal-rich soil horizons, offer an invaluable Late Quaternary record of pyrogenic carbon (PyC) additions to soils. A traditional source of archaeological, anthracological and palaeoecological data, the potential contribution of anthropogenic charcoal deposits to soil science and assessment of carbon (C) sequestration is often overlooked. If addition of biochar to soils is to form a key component of a low-C economy, crucial questions must be addressed relating to its longevity and behaviour in the soil environment. With rare exceptions, previous studies have focussed on short-term incubation experiments and field or pot trials, often neglecting important natural soil and environmental processes. This study addresses these issues by comparing the physicochemical properties of European anthropogenic charcoal-rich deposits, with 14C ages ranging from > 43 ka to Modern, to native soils (nearby control sites). We will present results from a study of 23 charcoal-rich soil cores, collected from a 'Pre-historic' ditch mound, a Bronze Age burnt mound, a Roman furnace, and post-mediaeval and Modern Meilers, situated along a climatic gradient from Mediterranean (Southern Italy) to Humid Temperate (South Wales). The ability of charcoal to alter fertility and retain plant-available nutrients was assessed by measuring soil cation- exchange capacity. Retention of refractory C by the charcoal deposits was evaluated from their total organic C (TOC) contents, atomic H:C and O:C ratios, and residues after acid- dichromate oxidation. Picked charcoal fragments were also compared with modern biochars and biomass using: 1) their thermogravimetric recalcitrance (R50) indices (Harvey et al. 2012); and 2) attenuated total reflectance (ATR) FT-IR data, to gauge the development of functional groups linked to the long-term oxidation of the particle surfaces. Radiocarbon dating was used to assess the ages of the deposits. Our study

  19. Hybrid mode-locked fiber ring laser using graphene and charcoal nanoparticles as saturable absorbers

    NASA Astrophysics Data System (ADS)

    Hu, Hongyu; Zhang, Xiang; Li, Wenbo; Dutta, Niloy K.

    2016-05-01

    A fiber ring laser which implements hybrid mode locking technique has been proposed and experimentally demonstrated to generate pulse train at 20 GHz repetition rate with ultrashort pulse width. Graphene and charcoal nano-particles acting as passive mode lockers are inserted into a rational harmonic mode-locked fiber laser to improve the performance. With graphene saturable absorbers, the pulse duration is shortened from 5.3 ps to 2.8 ps, and with charcoal nano-particles, it is shortened to 3.2 ps. The RF spectra show that supermode noise can be removed in the presence of the saturable absorbers. Numerical simulation of the pulse transmission has also been carried out, which shows good agreement with the experimental results.

  20. Workers' postural conditions in the charcoal production proccess based on vertical metallic cylynders.

    PubMed

    Maia, Ivana Márcia Oliveira; Francisco, Antonio Carlos de

    2012-01-01

    Considering the importance of posture to the workers' health in the production of charcoal, this paper presents an ergonomic research based on a biomechanical focus that aims to evaluate the posture adopted by these workers on the production of charcoal in vertical metallic cylinders. Thus, it was verified the incidence of pain and/or musculoskeletal injuries to these workers. Also, it was evaluated the weight carried by them and the positions taken in their daily tasks. Applying the Ergonomic Analysis of Labor, the data collection was done by directly observing the workers, registering images, by interviews, and posture analysis based on the OWAS method. The main results of the research show that there are postures with risks in the four levels of musculoskeletal injuries classified by OWAS, concluding that the method is imperative for ergonomic recommendations for minimization or eradication of suffering injury and worker's postural constraints.