Instrumentation at the Decade 80 solar house in Tucson, Arizona

NASA Technical Reports Server (NTRS)

1978-01-01

Modifications, problems and solutions for the instrumentation system that occurred during the period from May through September, 1978, are described. The solar house was built to show the use of copper in home building and to demonstrate the use of solar energy to provide space heating and cooling and domestic hot water. The auxiliary energy sources are electrical resistance heating for the domestic hot water and a gas-fired boiler for space heating and operation of the adsorption air conditioning units.

Eshelby's problem of a spherical inclusion eccentrically embedded in a finite spherical body

PubMed Central

He, Q.-C.

2017-01-01

Resorting to the superposition principle, the solution of Eshelby's problem of a spherical inclusion located eccentrically inside a finite spherical domain is obtained in two steps: (i) the solution to the problem of a spherical inclusion in an infinite space; (ii) the solution to the auxiliary problem of the corresponding finite spherical domain subjected to appropriate boundary conditions. Moreover, a set of functions called the sectional and harmonic deviators are proposed and developed to work out the auxiliary solution in a series form, including the displacement and Eshelby tensor fields. The analytical solutions are explicitly obtained and illustrated when the geometric and physical parameters and the boundary condition are specified. PMID:28293141

A time reversal algorithm in acoustic media with Dirac measure approximations

NASA Astrophysics Data System (ADS)

Bretin, Élie; Lucas, Carine; Privat, Yannick

2018-04-01

This article is devoted to the study of a photoacoustic tomography model, where one is led to consider the solution of the acoustic wave equation with a source term writing as a separated variables function in time and space, whose temporal component is in some sense close to the derivative of the Dirac distribution at t  =  0. This models a continuous wave laser illumination performed during a short interval of time. We introduce an algorithm for reconstructing the space component of the source term from the measure of the solution recorded by sensors during a time T all along the boundary of a connected bounded domain. It is based at the same time on the introduction of an auxiliary equivalent Cauchy problem allowing to derive explicit reconstruction formula and then to use of a deconvolution procedure. Numerical simulations illustrate our approach. Finally, this algorithm is also extended to elasticity wave systems.

Optimal bounds and extremal trajectories for time averages in nonlinear dynamical systems

NASA Astrophysics Data System (ADS)

Tobasco, Ian; Goluskin, David; Doering, Charles R.

2018-02-01

For any quantity of interest in a system governed by ordinary differential equations, it is natural to seek the largest (or smallest) long-time average among solution trajectories, as well as the extremal trajectories themselves. Upper bounds on time averages can be proved a priori using auxiliary functions, the optimal choice of which is a convex optimization problem. We prove that the problems of finding maximal trajectories and minimal auxiliary functions are strongly dual. Thus, auxiliary functions provide arbitrarily sharp upper bounds on time averages. Moreover, any nearly minimal auxiliary function provides phase space volumes in which all nearly maximal trajectories are guaranteed to lie. For polynomial equations, auxiliary functions can be constructed by semidefinite programming, which we illustrate using the Lorenz system.

[Determination of di (hydrogenated tallow alkyl) dimethyl ammonium compounds in textile auxiliaries by ultra-high performance liquid chromatography-tandem mass spectrometry].

PubMed

Zhu, Feng

2015-01-01

A method has been developed for the determination of di (hydrogenated tallow alkyl) dimethyl ammonium compounds (DHTDMAC) in textile auxiliaries by ultra-high performance liquid chromatography-tandem mass spectrometry. (UPLC-MS/MS). The samples were extracted and diluted with acidified methanol by 5% (v/v) formic acid under ultrasonic assistance. The separation was performed on an Eclipse Plus C18 column (50 mm x 2.1 mm, 1.8 microm) using 0.1% (v/v) formic acid solution and methanol as the mobile phases. Identification and quantification were achieved by UPLC-MS/MS with electrospray ionization (ESI) source in positive ion mode and multiple reaction monitoring (MRM) mode. The results indicated that the calibration curve of DHTDMAC showed good linear relationship between peak area and mass concentration in the range of 10-280 microg/L with the correlation coefficient (r2) of 0.9991. The limit of detection (LOD, S/N=3) and the limit of quantification (LOQ, S/N= 10) of this method were 3 mg/kg and 10 mg/kg, respectively. The average recoveries from three typical textile auxiliary matrices including dispersant, antistatic agent and fabric softener, at three spiked levels were in the range of 97.2%-108.3% with the relative standard deviations (RSDs) of 1.5%-4.6%. The method is sensitive, accurate, simple and effective for the analysis of DHTDMAC in textile auxiliaries.

Lubrication system with tolerance for reduced gravity

NASA Technical Reports Server (NTRS)

Portlock, Lawrence E. (Inventor); McCune, Michael E. (Inventor); Dobek, Louis J. (Inventor)

2012-01-01

A lubrication system includes an auxiliary lubricant tank 48, a supply conduit 58 extending from a source of lubricant 26 to the auxiliary lubricant tank. A reduced-G bypass line 108 branches from the conduit and enters the auxiliary tank at a first elevation E.sub.1. The system also includes an auxiliary tank discharge conduit 116, a portion of which resides within the tank. The resident portion has an opening 122 at least partially at a second elevation E.sub.2 higher than the first elevation.

Lubrication System with Tolerance for Reduced Gravity

NASA Technical Reports Server (NTRS)

Portlock, Lawrence E. (Inventor); McCune, Michael E. (Inventor); Dobek, Louis J. (Inventor)

2013-01-01

A lubrication system includes an auxiliary lubricant tank 48, a supply conduit 58 extending from a source of lubricant 26 to the auxiliary lubricant tank. A reduced-G bypass line 108 branches from the conduit and enters the auxiliary tank at a first elevation E.sub.1. The system also includes an auxiliary tank discharge conduit 116, a portion of which resides within the tank. The resident portion has an opening 122 at least partially at a second elevation E.sub.2 higher than the first elevation.

77 FR 54850 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-06

... sources in the auxiliary (center) fuel tank, main fuel tanks, and surge tanks caused by a wiring short or... on the rear spar, and installation of a TFE sleeve if necessary. This proposed AD would also add... sources in the auxiliary (center) fuel tank, main fuel tanks, and surge tanks caused by a wiring short or...

Integrating multiple data sources in species distribution modeling: A framework for data fusion

USGS Publications Warehouse

Pacifici, Krishna; Reich, Brian J.; Miller, David A.W.; Gardner, Beth; Stauffer, Glenn E.; Singh, Susheela; McKerrow, Alexa; Collazo, Jaime A.

2017-01-01

The last decade has seen a dramatic increase in the use of species distribution models (SDMs) to characterize patterns of species’ occurrence and abundance. Efforts to parameterize SDMs often create a tension between the quality and quantity of data available to fit models. Estimation methods that integrate both standardized and non-standardized data types offer a potential solution to the tradeoff between data quality and quantity. Recently several authors have developed approaches for jointly modeling two sources of data (one of high quality and one of lesser quality). We extend their work by allowing for explicit spatial autocorrelation in occurrence and detection error using a Multivariate Conditional Autoregressive (MVCAR) model and develop three models that share information in a less direct manner resulting in more robust performance when the auxiliary data is of lesser quality. We describe these three new approaches (“Shared,” “Correlation,” “Covariates”) for combining data sources and show their use in a case study of the Brown-headed Nuthatch in the Southeastern U.S. and through simulations. All three of the approaches which used the second data source improved out-of-sample predictions relative to a single data source (“Single”). When information in the second data source is of high quality, the Shared model performs the best, but the Correlation and Covariates model also perform well. When the information quality in the second data source is of lesser quality, the Correlation and Covariates model performed better suggesting they are robust alternatives when little is known about auxiliary data collected opportunistically or through citizen scientists. Methods that allow for both data types to be used will maximize the useful information available for estimating species distributions.

A new approach on auxiliary vehicle assignment in capacitated location routing problem

NASA Astrophysics Data System (ADS)

Bashiri, Mahdi; Rasoulinejad, Zeinab; Fallahzade, Ehsan

2016-03-01

The location routing problem (LRP) considers locating depots and vehicle routing decisions simultaneously. In classic LRP the number of customers in each route depends on the capacity of the vehicle. In this paper a capacitated LRP model with auxiliary vehicle assignment is presented in which the length of each route is not restricted by main vehicle capacity. Two kinds of vehicles are considered: main vehicles with higher capacity and fixed cost and auxiliary vehicles with lower capacity and fixed cost. The auxiliary vehicles can be added to the transportation system as an alternative strategy to cover the capacity limitations and they are just used to transfer goods from depots to vehicles and cannot serve the customers by themselves. To show the applicability of the proposed model, some numerical examples derived from the well-known instances are used. Moreover the model has been solved by some meta-heuristics for large sized instances. The results show the efficiency of the proposed model and the solution approach, considering the classic model and the exact solution approach, respectively.

A method for reducing the largest relative errors in Monte Carlo iterated-fission-source calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunter, J. L.; Sutton, T. M.

2013-07-01

In Monte Carlo iterated-fission-source calculations relative uncertainties on local tallies tend to be larger in lower-power regions and smaller in higher-power regions. Reducing the largest uncertainties to an acceptable level simply by running a larger number of neutron histories is often prohibitively expensive. The uniform fission site method has been developed to yield a more spatially-uniform distribution of relative uncertainties. This is accomplished by biasing the density of fission neutron source sites while not biasing the solution. The method is integrated into the source iteration process, and does not require any auxiliary forward or adjoint calculations. For a given amountmore » of computational effort, the use of the method results in a reduction of the largest uncertainties relative to the standard algorithm. Two variants of the method have been implemented and tested. Both have been shown to be effective. (authors)« less

Radiation effects on the flow of Powell-Eyring fluid past an unsteady inclined stretching sheet with non-uniform heat source/sink.

PubMed

Hayat, Tasawar; Asad, Sadia; Mustafa, Meraj; Alsaedi, Ahmed

2014-01-01

This study investigates the unsteady flow of Powell-Eyring fluid past an inclined stretching sheet. Unsteadiness in the flow is due to the time-dependence of the stretching velocity and wall temperature. Mathematical analysis is performed in the presence of thermal radiation and non-uniform heat source/sink. The relevant boundary layer equations are reduced into self-similar forms by suitable transformations. The analytic solutions are constructed in a series form by homotopy analysis method (HAM). The convergence interval of the auxiliary parameter is obtained. Graphical results displaying the influence of interesting parameters are given. Numerical values of skin friction coefficient and local Nusselt number are computed and analyzed.

Dispersive optical soliton solutions for higher order nonlinear Sasa-Satsuma equation in mono mode fibers via new auxiliary equation method

NASA Astrophysics Data System (ADS)

Khater, Mostafa M. A.; Seadawy, Aly R.; Lu, Dianchen

2018-01-01

In this research, we apply new technique for higher order nonlinear Schrödinger equation which is representing the propagation of short light pulses in the monomode optical fibers and the evolution of slowly varying packets of quasi-monochromatic waves in weakly nonlinear media that have dispersion. Nonlinear Schrödinger equation is one of the basic model in fiber optics. We apply new auxiliary equation method for nonlinear Sasa-Satsuma equation to obtain a new optical forms of solitary traveling wave solutions. Exact and solitary traveling wave solutions are obtained in different kinds like trigonometric, hyperbolic, exponential, rational functions, …, etc. These forms of solutions that we represent in this research prove the superiority of our new technique on almost thirteen powerful methods. The main merits of this method over the other methods are that it gives more general solutions with some free parameters.

Three dimensional radiative flow of magnetite-nanofluid with homogeneous-heterogeneous reactions

NASA Astrophysics Data System (ADS)

Hayat, Tasawar; Rashid, Madiha; Alsaedi, Ahmed

2018-03-01

Present communication deals with the effects of homogeneous-heterogeneous reactions in flow of nanofluid by non-linear stretching sheet. Water based nanofluid containing magnetite nanoparticles is considered. Non-linear radiation and non-uniform heat sink/source effects are examined. Non-linear differential systems are computed by Optimal homotopy analysis method (OHAM). Convergent solutions of nonlinear systems are established. The optimal data of auxiliary variables is obtained. Impact of several non-dimensional parameters for velocity components, temperature and concentration fields are examined. Graphs are plotted for analysis of surface drag force and heat transfer rate.

Distributed single source coding with side information

NASA Astrophysics Data System (ADS)

Vila-Forcen, Jose E.; Koval, Oleksiy; Voloshynovskiy, Sviatoslav V.

2004-01-01

In the paper we advocate image compression technique in the scope of distributed source coding framework. The novelty of the proposed approach is twofold: classical image compression is considered from the positions of source coding with side information and, contrarily to the existing scenarios, where side information is given explicitly, side information is created based on deterministic approximation of local image features. We consider an image in the transform domain as a realization of a source with a bounded codebook of symbols where each symbol represents a particular edge shape. The codebook is image independent and plays the role of auxiliary source. Due to the partial availability of side information at both encoder and decoder we treat our problem as a modification of Berger-Flynn-Gray problem and investigate a possible gain over the solutions when side information is either unavailable or available only at decoder. Finally, we present a practical compression algorithm for passport photo images based on our concept that demonstrates the superior performance in very low bit rate regime.

Environmental impact assessment of the incineration of municipal solid waste with auxiliary coal in China.

PubMed

Zhao, Yan; Xing, Wei; Lu, Wenjing; Zhang, Xu; Christensen, Thomas H

2012-10-01

The environmental impacts of waste incineration with auxiliary coal were investigated using the life-cycle-based software, EASEWASTE, based on the municipal solid waste (MSW) management system in Shuozhou City. In the current system, MSW is collected, transported, and incinerated with 250 kg of coal per ton of waste. Based on observed environmental impacts of incineration, fossil CO(2) and heavy metals were primary contributors to global warming and ecotoxicity in soil, respectively. Compared with incinerators using excess coal, incineration with adequate coal presents significant benefits in mitigating global warming, whereas incineration with a mass of coal can avoid more impacts to acidification, photochemical ozone and nutrient enrichment because of increased electricity substitution and reduced emission from coal power plants. The "Emission standard of air pollutants for thermal power plants (GB13223-2011)" implemented in 2012 introduced stricter policies on controlling SO(2) and NO(x) emissions from coal power plants. Thus, increased use of auxiliary coal during incineration yields fewer avoided impacts on acidification and nutrient enrichment. When two-thirds of ash is source-separated and landfilled, the incineration of rest-waste presents better results on global warming, acidification, nutrient enrichment, and even ecotoxicity in soil. This process is considered a promising solution for MSW management in Shuozhou City. Weighted normalized environmental impacts were assessed based on Chinese political reduction targets. Results indicate that heavy metal and acidic gas emissions should be given more attention in waste incineration. This study provides scientific support for the management of MSW systems dominated by incineration with auxiliary coal in China. Copyright © 2012 Elsevier Ltd. All rights reserved.

Analysis of Heat Transfers inside Counterflow Plate Heat Exchanger Augmented by an Auxiliary Fluid Flow

PubMed Central

Khaled, A.-R. A.

2014-01-01

Enhancement of heat transfers in counterflow plate heat exchanger due to presence of an intermediate auxiliary fluid flow is investigated. The intermediate auxiliary channel is supported by transverse conducting pins. The momentum and energy equations for the primary fluids are solved numerically and validated against a derived approximate analytical solution. A parametric study including the effect of the various plate heat exchanger, and auxiliary channel dimensionless parameters is conducted. Different enhancement performance indicators are computed. The various trends of parameters that can better enhance heat transfer rates above those for the conventional plate heat exchanger are identified. Large enhancement factors are obtained under fully developed flow conditions. The maximum enhancement factors can be increased by above 8.0- and 5.0-fold for the step and exponential distributions of the pins, respectively. Finally, counterflow plate heat exchangers with auxiliary fluid flows are recommended over the typical ones if these flows can be provided with the least cost. PMID:24719572

Analysis of heat transfers inside counterflow plate heat exchanger augmented by an auxiliary fluid flow.

PubMed

Khaled, A-R A

2014-01-01

Enhancement of heat transfers in counterflow plate heat exchanger due to presence of an intermediate auxiliary fluid flow is investigated. The intermediate auxiliary channel is supported by transverse conducting pins. The momentum and energy equations for the primary fluids are solved numerically and validated against a derived approximate analytical solution. A parametric study including the effect of the various plate heat exchanger, and auxiliary channel dimensionless parameters is conducted. Different enhancement performance indicators are computed. The various trends of parameters that can better enhance heat transfer rates above those for the conventional plate heat exchanger are identified. Large enhancement factors are obtained under fully developed flow conditions. The maximum enhancement factors can be increased by above 8.0- and 5.0-fold for the step and exponential distributions of the pins, respectively. Finally, counterflow plate heat exchangers with auxiliary fluid flows are recommended over the typical ones if these flows can be provided with the least cost.

Fast Response Polypyrrole Actuators with Auxiliary Electrodes

NASA Astrophysics Data System (ADS)

Zama, Tetsuji; Hara, Susumu; Takashima, Wataru; Kaneto, Keiichi

2005-11-01

Electrochemical polypyrrole (PPy) actuators, prepared electrochemically from a methyl benzoate solution of tetra-n-butylammonium trifluoromethanesulfonate (TBACF3SO3), have been studied to improve the response rate by two methods; 1) a PPy film attached with plural auxiliary electrodes of thin Au coils, 2) a PPy film equipped with a compliant Au electrode on one side of the film. With increasing the number of auxiliary electrodes for the first method, the film responded faster as if it were a shorter film. These results are due to the decrease in the IR voltage drop along the film from the electrodes and also due to the increased current to the whole film via plural electrodes. The PPy film with the Au thin layer (the second method) exhibited up to 8.8%/s strain rate, which was much faster than that (0.5%/s) without the auxiliary electrodes, keeping the maximum strain of 12--13%. The auxiliary electrodes improved not only the response speed of the PPy actuators but also the durability upon cycling electrochemically.

Precision control of high temperature furnaces using an auxiliary power supply and charged practice current flow

DOEpatents

Pollock, George G.

1997-01-01

Two power supplies are combined to control a furnace. A main power supply heats the furnace in the traditional manner, while the power from the auxiliary supply is introduced as a current flow through charged particles existing due to ionized gas or thermionic emission. The main power supply provides the bulk heating power and the auxiliary supply provides a precise and fast power source such that the precision of the total power delivered to the furnace is improved.

Injection of auxiliary electrons for increasing the plasma density in highly charged and high intensity ion sources.

PubMed

Odorici, F; Malferrari, L; Montanari, A; Rizzoli, R; Mascali, D; Castro, G; Celona, L; Gammino, S; Neri, L

2016-02-01

Different electron guns based on cold- or hot-cathode technologies have been developed since 2009 at INFN for operating within ECR plasma chambers as sources of auxiliary electrons, with the aim of boosting the source performances by means of a higher plasma lifetime and density. Their application to microwave discharge ion sources, where plasma is not confined, has required an improvement of the gun design, in order to "screen" the cathode from the plasma particles. Experimental tests carried out on a plasma reactor show a boost of the plasma density, ranging from 10% to 90% when the electron guns are used, as explained by plasma diffusion models.

Auxiliary variables for numerically solving nonlinear equations with softly broken symmetries.

PubMed

Olum, Ken D; Masoumi, Ali

2017-06-01

General methods for solving simultaneous nonlinear equations work by generating a sequence of approximate solutions that successively improve a measure of the total error. However, if the total error function has a narrow curved valley, the available techniques tend to find the solution after a very large number of steps, if ever. The solver first converges rapidly to the valley, but once there it converges extremely slowly to the solution. In this paper we show that in the specific physically important case where these valleys are the result of a softly broken symmetry, the solution can often be found much more quickly by adding the generators of the softly broken symmetry as auxiliary variables. This makes the number of variables more than the equations and hence there will be a family of solutions, any one of which would be acceptable. We present a procedure for finding solutions in this case and apply it to several simple examples and an important problem in the physics of false vacuum decay. We also provide a Mathematica package that implements Powell's hybrid method with the generalization to allow more variables than equations.

Precision control of high temperature furnaces using an auxiliary power supply and charged particle current flow

DOEpatents

Pollock, G.G.

1997-01-28

Two power supplies are combined to control a furnace. A main power supply heats the furnace in the traditional manner, while the power from the auxiliary supply is introduced as a current flow through charged particles existing due to ionized gas or thermionic emission. The main power supply provides the bulk heating power and the auxiliary supply provides a precise and fast power source such that the precision of the total power delivered to the furnace is improved. 5 figs.

Injection of auxiliary electrons for increasing the plasma density in highly charged and high intensity ion sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Odorici, F., E-mail: fabrizio.odorici@bo.infn.it; Malferrari, L.; Montanari, A.

Different electron guns based on cold- or hot-cathode technologies have been developed since 2009 at INFN for operating within ECR plasma chambers as sources of auxiliary electrons, with the aim of boosting the source performances by means of a higher plasma lifetime and density. Their application to microwave discharge ion sources, where plasma is not confined, has required an improvement of the gun design, in order to “screen” the cathode from the plasma particles. Experimental tests carried out on a plasma reactor show a boost of the plasma density, ranging from 10% to 90% when the electron guns are used,more » as explained by plasma diffusion models.« less

Optimal solutions for the evolution of a social obesity epidemic model

NASA Astrophysics Data System (ADS)

Sikander, Waseem; Khan, Umar; Mohyud-Din, Syed Tauseef

2017-06-01

In this work, a novel modification in the traditional homotopy perturbation method (HPM) is proposed by embedding an auxiliary parameter in the boundary condition. The scheme is used to carry out a mathematical evaluation of the social obesity epidemic model. The incidence of excess weight and obesity in adulthood population and prediction of its behavior in the coming years is analyzed by using a modified algorithm. The proposed method increases the convergence of the approximate analytical solution over the domain of the problem. Furthermore, a convenient way is considered for choosing an optimal value of auxiliary parameters via minimizing the total residual error. The graphical comparison of the obtained results with the standard HPM explicitly reveals the accuracy and efficiency of the developed scheme.

Characteristics of the solitary waves and rogue waves with interaction phenomena in a (2 + 1)-dimensional Breaking Soliton equation

NASA Astrophysics Data System (ADS)

Hossen, Md. Belal; Roshid, Harun-Or; Ali, M. Zulfikar

2018-05-01

Under inquisition in this paper is a (2 + 1)-dimensional Breaking Soliton equation, which can describe various nonlinear scenarios in fluid dynamics. Using the Bell polynomials, some proficient auxiliary functions are offered to apparently construct its bilinear form and corresponding soliton solutions which are different from the previous literatures. Moreover, a direct method is used to construct its rogue wave and solitary wave solutions using particular auxiliary function with the assist of bilinear formalism. Finally, the interactions between solitary waves and rogue waves are offered with a complete derivation. These results enhance the variety of the dynamics of higher dimensional nonlinear wave fields related to mathematical physics and engineering.

External control of electron energy distributions in a dual tandem inductively coupled plasma

NASA Astrophysics Data System (ADS)

Liu, Lei; Sridhar, Shyam; Zhu, Weiye; Donnelly, Vincent M.; Economou, Demetre J.; Logue, Michael D.; Kushner, Mark J.

2015-08-01

The control of electron energy probability functions (EEPFs) in low pressure partially ionized plasmas is typically accomplished through the format of the applied power. For example, through the use of pulse power, the EEPF can be modulated to produce shapes not possible under continuous wave excitation. This technique uses internal control. In this paper, we discuss a method for external control of EEPFs by transport of electrons between separately powered inductively coupled plasmas (ICPs). The reactor incorporates dual ICP sources (main and auxiliary) in a tandem geometry whose plasma volumes are separated by a grid. The auxiliary ICP is continuously powered while the main ICP is pulsed. Langmuir probe measurements of the EEPFs during the afterglow of the main ICP suggests that transport of hot electrons from the auxiliary plasma provided what is effectively an external source of energetic electrons. The tail of the EEPF and bulk electron temperature were then elevated in the afterglow of the main ICP by this external source of power. Results from a computer simulation for the evolution of the EEPFs concur with measured trends.

Reducing bias in survival under non-random temporary emigration

USGS Publications Warehouse

Peñaloza, Claudia L.; Kendall, William L.; Langtimm, Catherine Ann

2014-01-01

Despite intensive monitoring, temporary emigration from the sampling area can induce bias severe enough for managers to discard life-history parameter estimates toward the terminus of the times series (terminal bias). Under random temporary emigration unbiased parameters can be estimated with CJS models. However, unmodeled Markovian temporary emigration causes bias in parameter estimates and an unobservable state is required to model this type of emigration. The robust design is most flexible when modeling temporary emigration, and partial solutions to mitigate bias have been identified, nonetheless there are conditions were terminal bias prevails. Long-lived species with high adult survival and highly variable non-random temporary emigration present terminal bias in survival estimates, despite being modeled with the robust design and suggested constraints. Because this bias is due to uncertainty about the fate of individuals that are undetected toward the end of the time series, solutions should involve using additional information on survival status or location of these individuals at that time. Using simulation, we evaluated the performance of models that jointly analyze robust design data and an additional source of ancillary data (predictive covariate on temporary emigration, telemetry, dead recovery, or auxiliary resightings) in reducing terminal bias in survival estimates. The auxiliary resighting and predictive covariate models reduced terminal bias the most. Additional telemetry data was effective at reducing terminal bias only when individuals were tracked for a minimum of two years. High adult survival of long-lived species made the joint model with recovery data ineffective at reducing terminal bias because of small-sample bias. The naïve constraint model (last and penultimate temporary emigration parameters made equal), was the least efficient, though still able to reduce terminal bias when compared to an unconstrained model. Joint analysis of several sources of data improved parameter estimates and reduced terminal bias. Efforts to incorporate or acquire such data should be considered by researchers and wildlife managers, especially in the years leading up to status assessments of species of interest. Simulation modeling is a very cost effective method to explore the potential impacts of using different sources of data to produce high quality demographic data to inform management.

Optimal bounds and extremal trajectories for time averages in dynamical systems

NASA Astrophysics Data System (ADS)

Tobasco, Ian; Goluskin, David; Doering, Charles

2017-11-01

For systems governed by differential equations it is natural to seek extremal solution trajectories, maximizing or minimizing the long-time average of a given quantity of interest. A priori bounds on optima can be proved by constructing auxiliary functions satisfying certain point-wise inequalities, the verification of which does not require solving the underlying equations. We prove that for any bounded autonomous ODE, the problems of finding extremal trajectories on the one hand and optimal auxiliary functions on the other are strongly dual in the sense of convex duality. As a result, auxiliary functions provide arbitrarily sharp bounds on optimal time averages. Furthermore, nearly optimal auxiliary functions provide volumes in phase space where maximal and nearly maximal trajectories must lie. For polynomial systems, such functions can be constructed by semidefinite programming. We illustrate these ideas using the Lorenz system, producing explicit volumes in phase space where extremal trajectories are guaranteed to reside. Supported by NSF Award DMS-1515161, Van Loo Postdoctoral Fellowships, and the John Simon Guggenheim Foundation.

Advanced Unstructured Grid Generation for Complex Aerodynamic Applications

NASA Technical Reports Server (NTRS)

Pirzadeh, Shahyar Z.

2008-01-01

A new approach for distribution of grid points on the surface and in the volume has been developed and implemented in the NASA unstructured grid generation code VGRID. In addition to the point and line sources of prior work, the new approach utilizes surface and volume sources for automatic curvature-based grid sizing and convenient point distribution in the volume. A new exponential growth function produces smoother and more efficient grids and provides superior control over distribution of grid points in the field. All types of sources support anisotropic grid stretching which not only improves the grid economy but also provides more accurate solutions for certain aerodynamic applications. The new approach does not require a three-dimensional background grid as in the previous methods. Instead, it makes use of an efficient bounding-box auxiliary medium for storing grid parameters defined by surface sources. The new approach is less memory-intensive and more efficient computationally. The grids generated with the new method either eliminate the need for adaptive grid refinement for certain class of problems or provide high quality initial grids that would enhance the performance of many adaptation methods.

Advanced Unstructured Grid Generation for Complex Aerodynamic Applications

NASA Technical Reports Server (NTRS)

Pirzadeh, Shahyar

2010-01-01

A new approach for distribution of grid points on the surface and in the volume has been developed. In addition to the point and line sources of prior work, the new approach utilizes surface and volume sources for automatic curvature-based grid sizing and convenient point distribution in the volume. A new exponential growth function produces smoother and more efficient grids and provides superior control over distribution of grid points in the field. All types of sources support anisotropic grid stretching which not only improves the grid economy but also provides more accurate solutions for certain aerodynamic applications. The new approach does not require a three-dimensional background grid as in the previous methods. Instead, it makes use of an efficient bounding-box auxiliary medium for storing grid parameters defined by surface sources. The new approach is less memory-intensive and more efficient computationally. The grids generated with the new method either eliminate the need for adaptive grid refinement for certain class of problems or provide high quality initial grids that would enhance the performance of many adaptation methods.

Developing a Vacuum Electrospray Source To Implement Efficient Atmospheric Sampling for Miniature Ion Trap Mass Spectrometer.

PubMed

Yu, Quan; Zhang, Qian; Lu, Xinqiong; Qian, Xiang; Ni, Kai; Wang, Xiaohao

2017-12-05

The performance of a miniature mass spectrometer in atmospheric analysis is closely related to the design of its sampling system. In this study, a simplified vacuum electrospray ionization (VESI) source was developed based on a combination of several techniques, including the discontinuous atmospheric pressure interface, direct capillary sampling, and pneumatic-assisted electrospray. Pulsed air was used as a vital factor to facilitate the operation of electrospray ionization in the vacuum chamber. This VESI device can be used as an efficient atmospheric sampling interface when coupled with a miniature rectilinear ion trap (RIT) mass spectrometer. The developed VESI-RIT instrument enables regular ESI analysis of liquid, and its qualitative and quantitative capabilities have been characterized by using various solution samples. A limit of detection of 8 ppb could be attained for arginine in a methanol solution. In addition, extractive electrospray ionization of organic compounds can be implemented by using the same VESI device, as long as the gas analytes are injected with the pulsed auxiliary air. This methodology can extend the use of the proposed VESI technique to rapid and online analysis of gaseous and volatile samples.

Harmonic regression of Landsat time series for modeling attributes from national forest inventory data

Treesearch

Barry T. Wilson; Joseph F. Knight; Ronald E. McRoberts

2018-01-01

Imagery from the Landsat Program has been used frequently as a source of auxiliary data for modeling land cover, as well as a variety of attributes associated with tree cover. With ready access to all scenes in the archive since 2008 due to the USGS Landsat Data Policy, new approaches to deriving such auxiliary data from dense Landsat time series are required. Several...

Least-squares collocation meshless approach for radiative heat transfer in absorbing and scattering media

NASA Astrophysics Data System (ADS)

Liu, L. H.; Tan, J. Y.

2007-02-01

A least-squares collocation meshless method is employed for solving the radiative heat transfer in absorbing, emitting and scattering media. The least-squares collocation meshless method for radiative transfer is based on the discrete ordinates equation. A moving least-squares approximation is applied to construct the trial functions. Except for the collocation points which are used to construct the trial functions, a number of auxiliary points are also adopted to form the total residuals of the problem. The least-squares technique is used to obtain the solution of the problem by minimizing the summation of residuals of all collocation and auxiliary points. Three numerical examples are studied to illustrate the performance of this new solution method. The numerical results are compared with the other benchmark approximate solutions. By comparison, the results show that the least-squares collocation meshless method is efficient, accurate and stable, and can be used for solving the radiative heat transfer in absorbing, emitting and scattering media.

Invisibility problem in acoustics, electromagnetism and heat transfer. Inverse design method

NASA Astrophysics Data System (ADS)

Alekseev, G.; Tokhtina, A.; Soboleva, O.

2017-10-01

Two approaches (direct design and inverse design methods) for solving problems of designing devices providing invisibility of material bodies of detection using different physical fields - electromagnetic, acoustic and static are discussed. The second method is applied for solving problems of designing cloaking devices for the 3D stationary thermal scattering model. Based on this method the design problems under study are reduced to respective control problems. The material parameters (radial and tangential heat conductivities) of the inhomogeneous anisotropic medium filling the thermal cloak and the density of auxiliary heat sources play the role of controls. A unique solvability of direct thermal scattering problem in the Sobolev space is proved and the new estimates of solutions are established. Using these results, the solvability of control problem is proved and the optimality system is derived. Based on analysis of optimality system, the stability estimates of optimal solutions are established and numerical algorithms for solving particular thermal cloaking problem are proposed.

How Can We Afford This: Funding & Financing Means.

ERIC Educational Resources Information Center

Kaiser, Harvey H.

Sources of funds for campus capital renewal and replacement are discussed, including the operating budget, external sources, conversion of assets, and innovative techniques. Current funds can be obtained from tuition and fees, external sources, and sales and services of educational or auxiliary operations. Public universities are more heavily…

Ignition in tokamaks with modulated source of auxiliary heating

NASA Astrophysics Data System (ADS)

Morozov, D. Kh

2017-12-01

It is shown that the ignition may be achieved in tokamaks with the modulated power source. The time-averaged source power may be smaller than the steady-state source power, which is sufficient for the ignition. Nevertheless, the maximal power must be large enough, because the ignition must be achieved within a finite time interval.

Helicopter problems

NASA Technical Reports Server (NTRS)

Kussner, H G

1937-01-01

The present report deals with a number of the main problems requiring solution in the development of helicopters and concerning the lift, flying performance, stability, and drive. A complete solution is given for the stability of the helicopter with rigid blades and control surfaces. With a view to making a direct-lift propeller sufficient without the addition of auxiliary propellers, the "flapping drive" is assessed and its efficiency calculated.

Flexible high-voltage supply for experimental electron microscope

NASA Technical Reports Server (NTRS)

Chapman, G. L.; Jung, E. A.; Lewis, R. N.; Van Loon, L. S.; Welter, L. M.

1969-01-01

Scanning microscope uses a field-emission tip for the electron source, an electron gun that simultaneously accelerates and focuses electrons from the source, and one auxiliary lens to produce a final probe size at the specimen on the order of angstroms.

Impacts of dyebath auxiliaries on the reductive discoloration of Acid Orange 7 dye by high-carbon iron filings.

PubMed

Kumar, Raja; Sinha, Alok

This study proposed that the physicochemical effects of common dyebath auxiliaries on the bulk dye solution as well as on the iron surface can influence the reductive discoloration of effluent containing Acid Orange 7 (AO7) dye using high-carbon iron filings. Sodium chloride increased the discoloration rate because of the pitting corrosion on the iron surface, triggered by chloride anion. 'Salting out' effect of ammonium sulfate improved the reaction rate up to a certain concentration, beyond which it could compete with dye molecules for the reactive sites, as revealed by formed sulfite and sulfide. Urea drastically reduced the discoloration rates by its chaotropic effect on the bulk solution and by wrapping around the iron surface. Organic acids, namely acetic acid and citric acid, stimulated iron corrosion to improve the discoloration rates. The discoloration reaction was biphasic with an initial fast reaction phase, where in every case more than 70% discoloration was observed within 5 min of reaction, preceding a slow reaction phase. The experimental data could be well described using biphasic kinetics equation (R(2)> 0.997 in all cases) and a biphasic equation was developed considering the individual impact of co-existing auxiliaries on AO7 discoloration.

A generalized simplest equation method and its application to the Boussinesq-Burgers equation.

PubMed

Sudao, Bilige; Wang, Xiaomin

2015-01-01

In this paper, a generalized simplest equation method is proposed to seek exact solutions of nonlinear evolution equations (NLEEs). In the method, we chose a solution expression with a variable coefficient and a variable coefficient ordinary differential auxiliary equation. This method can yield a Bäcklund transformation between NLEEs and a related constraint equation. By dealing with the constraint equation, we can derive infinite number of exact solutions for NLEEs. These solutions include the traveling wave solutions, non-traveling wave solutions, multi-soliton solutions, rational solutions, and other types of solutions. As applications, we obtained wide classes of exact solutions for the Boussinesq-Burgers equation by using the generalized simplest equation method.

A Generalized Simplest Equation Method and Its Application to the Boussinesq-Burgers Equation

PubMed Central

Sudao, Bilige; Wang, Xiaomin

2015-01-01

In this paper, a generalized simplest equation method is proposed to seek exact solutions of nonlinear evolution equations (NLEEs). In the method, we chose a solution expression with a variable coefficient and a variable coefficient ordinary differential auxiliary equation. This method can yield a Bäcklund transformation between NLEEs and a related constraint equation. By dealing with the constraint equation, we can derive infinite number of exact solutions for NLEEs. These solutions include the traveling wave solutions, non-traveling wave solutions, multi-soliton solutions, rational solutions, and other types of solutions. As applications, we obtained wide classes of exact solutions for the Boussinesq-Burgers equation by using the generalized simplest equation method. PMID:25973605

A Highly Reliable and Cost-Efficient Multi-Sensor System for Land Vehicle Positioning.

PubMed

Li, Xu; Xu, Qimin; Li, Bin; Song, Xianghui

2016-05-25

In this paper, we propose a novel positioning solution for land vehicles which is highly reliable and cost-efficient. The proposed positioning system fuses information from the MEMS-based reduced inertial sensor system (RISS) which consists of one vertical gyroscope and two horizontal accelerometers, low-cost GPS, and supplementary sensors and sources. First, pitch and roll angle are accurately estimated based on a vehicle kinematic model. Meanwhile, the negative effect of the uncertain nonlinear drift of MEMS inertial sensors is eliminated by an H∞ filter. Further, a distributed-dual-H∞ filtering (DDHF) mechanism is adopted to address the uncertain nonlinear drift of the MEMS-RISS and make full use of the supplementary sensors and sources. The DDHF is composed of a main H∞ filter (MHF) and an auxiliary H∞ filter (AHF). Finally, a generalized regression neural network (GRNN) module with good approximation capability is specially designed for the MEMS-RISS. A hybrid methodology which combines the GRNN module and the AHF is utilized to compensate for RISS position errors during GPS outages. To verify the effectiveness of the proposed solution, road-test experiments with various scenarios were performed. The experimental results illustrate that the proposed system can achieve accurate and reliable positioning for land vehicles.

A Highly Reliable and Cost-Efficient Multi-Sensor System for Land Vehicle Positioning

PubMed Central

Li, Xu; Xu, Qimin; Li, Bin; Song, Xianghui

2016-01-01

In this paper, we propose a novel positioning solution for land vehicles which is highly reliable and cost-efficient. The proposed positioning system fuses information from the MEMS-based reduced inertial sensor system (RISS) which consists of one vertical gyroscope and two horizontal accelerometers, low-cost GPS, and supplementary sensors and sources. First, pitch and roll angle are accurately estimated based on a vehicle kinematic model. Meanwhile, the negative effect of the uncertain nonlinear drift of MEMS inertial sensors is eliminated by an H∞ filter. Further, a distributed-dual-H∞ filtering (DDHF) mechanism is adopted to address the uncertain nonlinear drift of the MEMS-RISS and make full use of the supplementary sensors and sources. The DDHF is composed of a main H∞ filter (MHF) and an auxiliary H∞ filter (AHF). Finally, a generalized regression neural network (GRNN) module with good approximation capability is specially designed for the MEMS-RISS. A hybrid methodology which combines the GRNN module and the AHF is utilized to compensate for RISS position errors during GPS outages. To verify the effectiveness of the proposed solution, road-test experiments with various scenarios were performed. The experimental results illustrate that the proposed system can achieve accurate and reliable positioning for land vehicles. PMID:27231917

A modular Space Station/Base electrical power system - Requirements and design study.

NASA Technical Reports Server (NTRS)

Eliason, J. T.; Adkisson, W. B.

1972-01-01

The requirements and procedures necessary for definition and specification of an electrical power system (EPS) for the future space station are discussed herein. The considered space station EPS consists of a replaceable main power module with self-contained auxiliary power, guidance, control, and communication subsystems. This independent power source may 'plug into' a space station module which has its own electrical distribution, control, power conditioning, and auxiliary power subsystems. Integration problems are discussed, and a transmission system selected with local floor-by-floor power conditioning and distribution in the station module. This technique eliminates the need for an immediate long range decision on the ultimate space base power sources by providing capability for almost any currently considered option.

Application of machine learning algorithms to the study of noise artifacts in gravitational-wave data

NASA Astrophysics Data System (ADS)

Biswas, Rahul; Blackburn, Lindy; Cao, Junwei; Essick, Reed; Hodge, Kari Alison; Katsavounidis, Erotokritos; Kim, Kyungmin; Kim, Young-Min; Le Bigot, Eric-Olivier; Lee, Chang-Hwan; Oh, John J.; Oh, Sang Hoon; Son, Edwin J.; Tao, Ye; Vaulin, Ruslan; Wang, Xiaoge

2013-09-01

The sensitivity of searches for astrophysical transients in data from the Laser Interferometer Gravitational-wave Observatory (LIGO) is generally limited by the presence of transient, non-Gaussian noise artifacts, which occur at a high enough rate such that accidental coincidence across multiple detectors is non-negligible. These “glitches” can easily be mistaken for transient gravitational-wave signals, and their robust identification and removal will help any search for astrophysical gravitational waves. We apply machine-learning algorithms (MLAs) to the problem, using data from auxiliary channels within the LIGO detectors that monitor degrees of freedom unaffected by astrophysical signals. Noise sources may produce artifacts in these auxiliary channels as well as the gravitational-wave channel. The number of auxiliary-channel parameters describing these disturbances may also be extremely large; high dimensionality is an area where MLAs are particularly well suited. We demonstrate the feasibility and applicability of three different MLAs: artificial neural networks, support vector machines, and random forests. These classifiers identify and remove a substantial fraction of the glitches present in two different data sets: four weeks of LIGO’s fourth science run and one week of LIGO’s sixth science run. We observe that all three algorithms agree on which events are glitches to within 10% for the sixth-science-run data, and support this by showing that the different optimization criteria used by each classifier generate the same decision surface, based on a likelihood-ratio statistic. Furthermore, we find that all classifiers obtain similar performance to the benchmark algorithm, the ordered veto list, which is optimized to detect pairwise correlations between transients in LIGO auxiliary channels and glitches in the gravitational-wave data. This suggests that most of the useful information currently extracted from the auxiliary channels is already described by this model. Future performance gains are thus likely to involve additional sources of information, rather than improvements in the classification algorithms themselves. We discuss several plausible sources of such new information as well as the ways of propagating it through the classifiers into gravitational-wave searches.

Uncertainty in biological monitoring: a framework for data collection and analysis to account for multiple sources of sampling bias

USGS Publications Warehouse

Ruiz-Gutierrez, Viviana; Hooten, Melvin B.; Campbell Grant, Evan H.

2016-01-01

Biological monitoring programmes are increasingly relying upon large volumes of citizen-science data to improve the scope and spatial coverage of information, challenging the scientific community to develop design and model-based approaches to improve inference.Recent statistical models in ecology have been developed to accommodate false-negative errors, although current work points to false-positive errors as equally important sources of bias. This is of particular concern for the success of any monitoring programme given that rates as small as 3% could lead to the overestimation of the occurrence of rare events by as much as 50%, and even small false-positive rates can severely bias estimates of occurrence dynamics.We present an integrated, computationally efficient Bayesian hierarchical model to correct for false-positive and false-negative errors in detection/non-detection data. Our model combines independent, auxiliary data sources with field observations to improve the estimation of false-positive rates, when a subset of field observations cannot be validated a posteriori or assumed as perfect. We evaluated the performance of the model across a range of occurrence rates, false-positive and false-negative errors, and quantity of auxiliary data.The model performed well under all simulated scenarios, and we were able to identify critical auxiliary data characteristics which resulted in improved inference. We applied our false-positive model to a large-scale, citizen-science monitoring programme for anurans in the north-eastern United States, using auxiliary data from an experiment designed to estimate false-positive error rates. Not correcting for false-positive rates resulted in biased estimates of occupancy in 4 of the 10 anuran species we analysed, leading to an overestimation of the average number of occupied survey routes by as much as 70%.The framework we present for data collection and analysis is able to efficiently provide reliable inference for occurrence patterns using data from a citizen-science monitoring programme. However, our approach is applicable to data generated by any type of research and monitoring programme, independent of skill level or scale, when effort is placed on obtaining auxiliary information on false-positive rates.

Cogeneration technology alternatives study. Volume 4: Heat Sources, balance of plant and auxiliary systems

NASA Technical Reports Server (NTRS)

1980-01-01

Data and information established for heat sources balance of plant items, thermal energy storage, and heat pumps are presented. Design case descriptions are given along with projected performance values. Capital cost estimates for representative cogeneration plants are also presented.

Modeling and observations of an elevated, moving infrasonic source: Eigenray methods.

PubMed

Blom, Philip; Waxler, Roger

2017-04-01

The acoustic ray tracing relations are extended by the inclusion of auxiliary parameters describing variations in the spatial ray coordinates and eikonal vector due to changes in the initial conditions. Computation of these parameters allows one to define the geometric spreading factor along individual ray paths and assists in identification of caustic surfaces so that phase shifts can be easily identified. A method is developed leveraging the auxiliary parameters to identify propagation paths connecting specific source-receiver geometries, termed eigenrays. The newly introduced method is found to be highly efficient in cases where propagation is non-planar due to horizontal variations in the propagation medium or the presence of cross winds. The eigenray method is utilized in analysis of infrasonic signals produced by a multi-stage sounding rocket launch with promising results for applications of tracking aeroacoustic sources in the atmosphere and specifically to analysis of motor performance during dynamic tests.

Computer programs for the solution of systems of linear algebraic equations

NASA Technical Reports Server (NTRS)

Sequi, W. T.

1973-01-01

FORTRAN subprograms for the solution of systems of linear algebraic equations are described, listed, and evaluated in this report. Procedures considered are direct solution, iteration, and matrix inversion. Both incore methods and those which utilize auxiliary data storage devices are considered. Some of the subroutines evaluated require the entire coefficient matrix to be in core, whereas others account for banding or sparceness of the system. General recommendations relative to equation solving are made, and on the basis of tests, specific subprograms are recommended.

Work Truck Idling Reduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2017-03-01

Hybrid utility trucks, with auxiliary power sources for on-board equipment, significantly reduce unnecessary idling resulting in fuel costs savings, less engine wear, and reduction in noise and emissions.

Online Heterogeneous Transfer by Hedge Ensemble of Offline and Online Decisions.

PubMed

Yan, Yuguang; Wu, Qingyao; Tan, Mingkui; Ng, Michael K; Min, Huaqing; Tsang, Ivor W

2017-10-10

In this paper, we study the online heterogeneous transfer (OHT) learning problem, where the target data of interest arrive in an online manner, while the source data and auxiliary co-occurrence data are from offline sources and can be easily annotated. OHT is very challenging, since the feature spaces of the source and target domains are different. To address this, we propose a novel technique called OHT by hedge ensemble by exploiting both offline knowledge and online knowledge of different domains. To this end, we build an offline decision function based on a heterogeneous similarity that is constructed using labeled source data and unlabeled auxiliary co-occurrence data. After that, an online decision function is learned from the target data. Last, we employ a hedge weighting strategy to combine the offline and online decision functions to exploit knowledge from the source and target domains of different feature spaces. We also provide a theoretical analysis regarding the mistake bounds of the proposed approach. Comprehensive experiments on three real-world data sets demonstrate the effectiveness of the proposed technique.

ADMS State of the Industry and Gap Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agalgaonkar, Yashodhan P.; Marinovici, Maria C.; Vadari, Subramanian V.

2016-03-31

An Advanced distribution management system (ADMS) is a platform for optimized distribution system operational management. This platform comprises of distribution management system (DMS) applications, supervisory control and data acquisition (SCADA), outage management system (OMS), and distributed energy resource management system (DERMS). One of the primary objectives of this work is to study and analyze several ADMS component and auxiliary systems. All the important component and auxiliary systems, SCADA, GISs, DMSs, AMRs/AMIs, OMSs, and DERMS, are discussed in this report. Their current generation technologies are analyzed, and their integration (or evolution) with an ADMS technology is discussed. An ADMS technology statemore » of the art and gap analysis is also presented. There are two technical gaps observed. The integration challenge between the component operational systems is the single largest challenge for ADMS design and deployment. Another significant challenge noted is concerning essential ADMS applications, for instance, fault location, isolation, and service restoration (FLISR), volt-var optimization (VVO), etc. There are a relatively small number of ADMS application developers as ADMS software platform is not open source. There is another critical gap and while not being technical in nature (when compared the two above) is still important to consider. The data models currently residing in utility GIS systems are either incomplete or inaccurate or both. This data is essential for planning and operations because it is typically one of the primary sources from which power system model are created. To achieve the full potential of ADMS, the ability to execute acute Power Flow solution is an important pre-requisite. These critical gaps are hindering wider Utility adoption of an ADMS technology. The development of an open architecture platform can eliminate many of these barriers and also aid seamless integration of distribution Utility legacy systems with an ADMS.« less

Simulation and Performance Analysis of Lithium Battery Bank Mounted on the Hybrid Power System for Mobile Public Health Center

NASA Astrophysics Data System (ADS)

Busono, Pratondo; Kartini, Evvy

2013-07-01

Mobile medical clinic has been proposed to serve homeless people, people in the disaster area or in the remote area where no health service exist. At that site, a number of essential services such as primary health care, general health screening, medical treatment and emergency/rescue operations are required. Such services usually requires on board electrical equipments such as refrigerators, komputer, power tools and medical equipments. To supply such electrical equipments, it needs extra auxiliary power sources, in addition of standard automotive power supply. The auxiliary power source specifically design to supply non automotive load which may have similar configuration, but usually uses high power alternator rated and larger deep cycle on board battery bank. This study covers the modeling and dynamic simulation of auxiliary power source/battery to supply the medical equipment and other electrical equipments on board. It consists a variable speed diesel generator set, photovoltaic (PV) generator mounted on the roof of the car, a rechargable battery bank. As an initial step in the system design, a simulation study was performed. The simulation is conducted in the system level. Simulation results shows that dynamical behaviour by means of current density, voltage and power plot over a chosen time range, and functional behaviour such as charging and discharging characteristic of the battery bank can be obtained.

The Search for Alternative Sources of Funding: Community Colleges and Private Fund-Raising.

ERIC Educational Resources Information Center

Bock, Daniel E.; Sullins, W. Robert

1987-01-01

Discusses various sources of private funds available to community colleges, including foundations, alumni, life-income gifts and annuity programs, corporations, and auxiliary enterprises. Identifies key members of a college's resource development team and warns of risks of increasing dependency on private funds. (DMM)

Hybridisations of Variable Neighbourhood Search and Modified Simplex Elements to Harmony Search and Shuffled Frog Leaping Algorithms for Process Optimisations

NASA Astrophysics Data System (ADS)

Aungkulanon, P.; Luangpaiboon, P.

2010-10-01

Nowadays, the engineering problem systems are large and complicated. An effective finite sequence of instructions for solving these problems can be categorised into optimisation and meta-heuristic algorithms. Though the best decision variable levels from some sets of available alternatives cannot be done, meta-heuristics is an alternative for experience-based techniques that rapidly help in problem solving, learning and discovery in the hope of obtaining a more efficient or more robust procedure. All meta-heuristics provide auxiliary procedures in terms of their own tooled box functions. It has been shown that the effectiveness of all meta-heuristics depends almost exclusively on these auxiliary functions. In fact, the auxiliary procedure from one can be implemented into other meta-heuristics. Well-known meta-heuristics of harmony search (HSA) and shuffled frog-leaping algorithms (SFLA) are compared with their hybridisations. HSA is used to produce a near optimal solution under a consideration of the perfect state of harmony of the improvisation process of musicians. A meta-heuristic of the SFLA, based on a population, is a cooperative search metaphor inspired by natural memetics. It includes elements of local search and global information exchange. This study presents solution procedures via constrained and unconstrained problems with different natures of single and multi peak surfaces including a curved ridge surface. Both meta-heuristics are modified via variable neighbourhood search method (VNSM) philosophy including a modified simplex method (MSM). The basic idea is the change of neighbourhoods during searching for a better solution. The hybridisations proceed by a descent method to a local minimum exploring then, systematically or at random, increasingly distant neighbourhoods of this local solution. The results show that the variant of HSA with VNSM and MSM seems to be better in terms of the mean and variance of design points and yields.

Constructing analytic solutions on the Tricomi equation

NASA Astrophysics Data System (ADS)

Ghiasi, Emran Khoshrouye; Saleh, Reza

2018-04-01

In this paper, homotopy analysis method (HAM) and variational iteration method (VIM) are utilized to derive the approximate solutions of the Tricomi equation. Afterwards, the HAM is optimized to accelerate the convergence of the series solution by minimizing its square residual error at any order of the approximation. It is found that effect of the optimal values of auxiliary parameter on the convergence of the series solution is not negligible. Furthermore, the present results are found to agree well with those obtained through a closed-form equation available in the literature. To conclude, it is seen that the two are effective to achieve the solution of the partial differential equations.

User's guide for a large signal computer model of the helical traveling wave tube

NASA Technical Reports Server (NTRS)

Palmer, Raymond W.

1992-01-01

The use is described of a successful large-signal, two-dimensional (axisymmetric), deformable disk computer model of the helical traveling wave tube amplifier, an extensively revised and operationally simplified version. We also discuss program input and output and the auxiliary files necessary for operation. Included is a sample problem and its input data and output results. Interested parties may now obtain from the author the FORTRAN source code, auxiliary files, and sample input data on a standard floppy diskette, the contents of which are described herein.

Photoplus: auxiliary information for printed images based on distributed source coding

NASA Astrophysics Data System (ADS)

Samadani, Ramin; Mukherjee, Debargha

2008-01-01

A printed photograph is difficult to reuse because the digital information that generated the print may no longer be available. This paper describes a mechanism for approximating the original digital image by combining a scan of the printed photograph with small amounts of digital auxiliary information kept together with the print. The auxiliary information consists of a small amount of digital data to enable accurate registration and color-reproduction, followed by a larger amount of digital data to recover residual errors and lost frequencies by distributed Wyner-Ziv coding techniques. Approximating the original digital image enables many uses, including making good quality reprints from the original print, even when they are faded many years later. In essence, the print itself becomes the currency for archiving and repurposing digital images, without requiring computer infrastructure.

46 CFR 28.355 - Main source of electrical power.

Code of Federal Regulations, 2012 CFR

2012-10-01

... auxiliaries and controls; (2) Interior lighting; (3) Steering systems; (4) Communication systems; (5) Navigation equipment and navigation lights; (6) Fire protection or detection equipment; (7) Bilge pumps; or...

46 CFR 28.355 - Main source of electrical power.

Code of Federal Regulations, 2011 CFR

2011-10-01

... auxiliaries and controls; (2) Interior lighting; (3) Steering systems; (4) Communication systems; (5) Navigation equipment and navigation lights; (6) Fire protection or detection equipment; (7) Bilge pumps; or...

46 CFR 28.355 - Main source of electrical power.

Code of Federal Regulations, 2013 CFR

2013-10-01

... auxiliaries and controls; (2) Interior lighting; (3) Steering systems; (4) Communication systems; (5) Navigation equipment and navigation lights; (6) Fire protection or detection equipment; (7) Bilge pumps; or...

46 CFR 28.355 - Main source of electrical power.

Code of Federal Regulations, 2010 CFR

2010-10-01

... auxiliaries and controls; (2) Interior lighting; (3) Steering systems; (4) Communication systems; (5) Navigation equipment and navigation lights; (6) Fire protection or detection equipment; (7) Bilge pumps; or...

Konnen Computer das Sprachproblem losen (Can Computers Solve the Language Problem)?

ERIC Educational Resources Information Center

Zeilinger, Michael

1972-01-01

Various computer applications in linguistics, primarily speech synthesis and machine translation, are reviewed. Although the computer proves useful for statistics, dictionary building and programmed instruction, the promulgation of a world auxiliary language is considered a more human and practical solution to the international communication…

The Poisson-Helmholtz-Boltzmann model.

PubMed

Bohinc, K; Shrestha, A; May, S

2011-10-01

We present a mean-field model of a one-component electrolyte solution where the mobile ions interact not only via Coulomb interactions but also through a repulsive non-electrostatic Yukawa potential. Our choice of the Yukawa potential represents a simple model for solvent-mediated interactions between ions. We employ a local formulation of the mean-field free energy through the use of two auxiliary potentials, an electrostatic and a non-electrostatic potential. Functional minimization of the mean-field free energy leads to two coupled local differential equations, the Poisson-Boltzmann equation and the Helmholtz-Boltzmann equation. Their boundary conditions account for the sources of both the electrostatic and non-electrostatic interactions on the surface of all macroions that reside in the solution. We analyze a specific example, two like-charged planar surfaces with their mobile counterions forming the electrolyte solution. For this system we calculate the pressure between the two surfaces, and we analyze its dependence on the strength of the Yukawa potential and on the non-electrostatic interactions of the mobile ions with the planar macroion surfaces. In addition, we demonstrate that our mean-field model is consistent with the contact theorem, and we outline its generalization to arbitrary interaction potentials through the use of a Laplace transformation. © EDP Sciences / Società Italiana di Fisica / Springer-Verlag 2011

Natural convection liquid desiccant loop as an auxiliary air conditioning system: investigating the operational parameters

NASA Astrophysics Data System (ADS)

Fazilati, Mohammad Ali; Alemrajabi, Ali Akbar; Sedaghat, Ahmad

2018-03-01

Liquid desiccant air conditioning system with natural convection was presented previously as a new generation of AC systems. The system consists of two three-fluid energy exchangers namely absorber and regenerator in which the action of air dehumidifying and desiccant regeneration is done, respectively. The influence of working parameters on system performance including the heat source and heat sink temperature, concentration of desiccant solution fills the system initially and humidity content of inlet air to regenerator is investigated experimentally. The heat source temperatures of 50 °C and 60 °C, heat sink temperatures of 15 °C and 20 °C and desiccant concentrations of 30% and 34%, are examined here. The inlet air to regenerator has temperature of 38.5 °C and three relative humidity of 14%, 38% and 44%. In all experiments, the inlet air to absorber has temperature of 31 °C and relative humidity of 75%. By inspecting evaluation indexes of system, it is revealed that higher startup desiccant concentration solution is more beneficial for all study cases. It is also observed although the highest/lowest temperature heat source/heat sink is most suitable for best system operation, increasing the heat source temperature should be accompanied with decreasing heat sink temperature. Using drier air stream for regenerator inlet does not necessarily improve system performance; and the air stream with proper value of humidity content should be employed. Finally after running the system in its best working condition, the coefficient of performance (COP) reached 4.66 which verified to be higher than when the same air conditioning task done by a conventional vapor compression system, in which case the COP was 3.38.

76 FR 22385 - Fisheries of the Caribbean; Southeast Data, Assessment, and Review (SEDAR); Public Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-21

... sources for providing information on life history characteristics, catch statistics, discard estimates... people with disabilities. Requests for sign language interpretation or other auxiliary aids should be...

Cancer Related-Knowledge - Small Area Estimates

Cancer.gov

These model-based estimates are produced using statistical models that combine data from the Health Information National Trends Survey, and auxiliary variables obtained from relevant sources and borrow strength from other areas with similar characteristics.

Modification of anisotropic plasma diffusion via auxiliary electrons emitted by a carbon nanotubes-based electron gun in an electron cyclotron resonance ion source.

PubMed

Malferrari, L; Odorici, F; Veronese, G P; Rizzoli, R; Mascali, D; Celona, L; Gammino, S; Castro, G; Miracoli, R; Serafino, T

2012-02-01

The diffusion mechanism in magnetized plasmas is a largely debated issue. A short circuit model was proposed by Simon, assuming fluxes of lost particles along the axial (electrons) and radial (ions) directions which can be compensated, to preserve the quasi-neutrality, by currents flowing throughout the conducting plasma chamber walls. We hereby propose a new method to modify Simon's currents via electrons injected by a carbon nanotubes-based electron gun. We found this improves the source performances, increasing the output current for several charge states. The method is especially sensitive to the pumping frequency. Output currents for given charge states, at different auxiliary electron currents, will be reported in the paper and the influence of the frequency tuning on the compensation mechanism will be discussed.

The advanced thermionic converter with microwave power as an auxiliary ionization source

NASA Technical Reports Server (NTRS)

Manikopoulos, C. N.; Hatziprocopiou, M.; Chiu, H. S.; Shaw, D. T.

1978-01-01

In the search for auxiliary sources of ionization for the advanced thermionic converter plasma, as required for terrestial applications, the use of externally applied microwave power is considered. The present work is part of the advanced model thermionic converter development research currently performed at the laboratory for Power and Environmental Studies at SUNY Buffalo. Microwave power in the frequency range 1-3 GHz is used to externally pump a thermionic converter and the results are compared to the theoretical model proposed by Lam (1976) in describing the thermionic converter plasma. The electron temperature of the plasma is found to be raised considerably by effective microwave heating which results in the disappearance of the double sheath ordinarily erected in front of the emitter. The experimental data agree satisfactorily with theory in the low current region.

Primordial cosmology in mimetic born-infeld gravity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bouhmadi-Lopez, Mariam; Chen, Che -Yu; Chen, Pisin

Here, the Eddington-inspired-Born-Infeld (EiBI) model is reformulated within the mimetic approach. In the presence of a mimetic field, the model contains non-trivial vacuum solutions which could be free of spacetime singularity because of the Born-Infeld nature of the theory. We study a realistic primordial vacuum universe and prove the existence of regular solutions, such as primordial inflationary solutions of de Sitter type or bouncing solutions. Besides, the linear instabilities present in the EiBI model are found to be avoidable for some interesting bouncing solutions in which the physical metric as well as the auxiliary metric are regular at the backgroundmore » level.« less

Primordial cosmology in mimetic born-infeld gravity

DOE PAGES

Bouhmadi-Lopez, Mariam; Chen, Che -Yu; Chen, Pisin

2017-11-29

Here, the Eddington-inspired-Born-Infeld (EiBI) model is reformulated within the mimetic approach. In the presence of a mimetic field, the model contains non-trivial vacuum solutions which could be free of spacetime singularity because of the Born-Infeld nature of the theory. We study a realistic primordial vacuum universe and prove the existence of regular solutions, such as primordial inflationary solutions of de Sitter type or bouncing solutions. Besides, the linear instabilities present in the EiBI model are found to be avoidable for some interesting bouncing solutions in which the physical metric as well as the auxiliary metric are regular at the backgroundmore » level.« less

In vitro antimicrobial and anti-endotoxin action of Zingiber Officinale as auxiliary chemical and medicament combined to calcium hydroxide and chlorhexidine.

PubMed

Valera, Marcia Carneiro; Cardoso, Flávia Goulart da Rosa; Maekawa, Lilian Eiko; Camargo, Carlos Henrique Ribeiro; de Oliveira, Luciane Dias; Carvalho, Cláudio Antônio Talge

2015-01-01

This study was conducted in vitro to compare the effectiveness of Zingiber Officinale as an auxiliary chemical substance followed by placement of different intra-canal medication in removing endotoxins and cultivable micro-organisms from infected root canals. Seventy-two root canals were contaminated with Enterococcus faecalis, Candida albicans and Escherichia coli for 28 days. After, the teeth were instrumented using Zingiber Officinale and divided into six groups according to the intra-canal medication: chlorhexidine gel; calcium hydroxide + chlorhexidine gel; glycolic ginger extract; calcium hydroxide + glycolic ginger extract; calcium hydroxide + saline solution and saline solution (control). Sample collections were performed after root canal contamination (Baseline; S1), after instrumentation (S2), 7 days after instrumentation (S3), after 14 days with intra-canal medication (S4) and 7 days after removal of intra-canal medication (S5). The results were analyzed by the Kruskal-Wallis and Dunn tests. It was observed that in S2 and S3 there was significant reduction of the micro-organisms and the quantity of endotoxins after instrumentation. In samples S4 and S5 there was complete elimination of micro-organisms and significant reduction of endotoxins. It was concluded that Zingiber Officinale as an auxiliary chemical substance was effective on the micro-organisms tested, yet was unable to eliminate the endotoxins. Similarly, the intra-canal medication were effective on micro-organisms, yet did not completely eliminate the endotoxins.

Solitary traveling wave solutions of pressure equation of bubbly liquids with examination for viscosity and heat transfer

NASA Astrophysics Data System (ADS)

Khater, Mostafa M. A.; Seadawy, Aly R.; Lu, Dianchen

2018-03-01

In this research, we investigate one of the most popular model in nature and also industrial which is the pressure equation of bubbly liquids with examination for viscosity and heat transfer which has many application in nature and engineering. Understanding the physical meaning of exact and solitary traveling wave solutions for this equation gives the researchers in this field a great clear vision of the pressure waves in a mixture liquid and gas bubbles taking into consideration the viscosity of liquid and the heat transfer and also dynamics of contrast agents in the blood flow at ultrasonic researches. To achieve our goal, we apply three different methods which are extended tanh-function method, extended simple equation method and a new auxiliary equation method on this equation. We obtained exact and solitary traveling wave solutions and we also discuss the similarity and difference between these three method and make a comparison between results that we obtained with another results that obtained with the different researchers using different methods. All of these results and discussion explained the fact that our new auxiliary equation method is considered to be the most general, powerful and the most result-oriented. These kinds of solutions and discussion allow for the understanding of the phenomenon and its intrinsic properties as well as the ease of way of application and its applicability to other phenomena.

On the Tracy-Widomβ Distribution for β=6

NASA Astrophysics Data System (ADS)

Grava, Tamara; Its, Alexander; Kapaev, Andrei; Mezzadri, Francesco

2016-11-01

We study the Tracy-Widom distribution function for Dyson's β-ensemble with β = 6. The starting point of our analysis is the recent work of I. Rumanov where he produces a Lax-pair representation for the Bloemendal-Virág equation. The latter is a linear PDE which describes the Tracy-Widom functions corresponding to general values of β. Using his Lax pair, Rumanov derives an explicit formula for the Tracy-Widom β=6 function in terms of the second Painlevé transcendent and the solution of an auxiliary ODE. Rumanov also shows that this formula allows him to derive formally the asymptotic expansion of the Tracy-Widom function. Our goal is to make Rumanov's approach and hence the asymptotic analysis it provides rigorous. In this paper, the first one in a sequel, we show that Rumanov's Lax-pair can be interpreted as a certain gauge transformation of the standard Lax pair for the second Painlevé equation. This gauge transformation though contains functional parameters which are defined via some auxiliary nonlinear ODE which is equivalent to the auxiliary ODE of Rumanov's formula. The gauge-interpretation of Rumanov's Lax-pair allows us to highlight the steps of the original Rumanov's method which needs rigorous justifications in order to make the method complete. We provide a rigorous justification of one of these steps. Namely, we prove that the Painlevé function involved in Rumanov's formula is indeed, as it has been suggested by Rumanov, the Hastings-McLeod solution of the second Painlevé equation. The key issue which we also discuss and which is still open is the question of integrability of the auxiliary ODE in Rumanov's formula. We note that this question is crucial for the rigorous asymptotic analysis of the Tracy-Widom function. We also notice that our work is a partial answer to one of the problems related to the β-ensembles formulated by Percy Deift during the June 2015 Montreal Conference on integrable systems.

Response-only method for damage detection of beam-like structures using high accuracy frequencies with auxiliary mass spatial probing

NASA Astrophysics Data System (ADS)

Zhong, Shuncong; Oyadiji, S. Olutunde; Ding, Kang

2008-04-01

This paper proposes a new approach based on auxiliary mass spatial probing using spectral centre correction method (SCCM), to provide a simple solution for damage detection by just using the response time history of beam-like structures. The natural frequencies of a damaged beam with a traversing auxiliary mass change due to change in the inertia of the beam as the auxiliary mass is traversed along the beam, as well as the point-to-point variations in the flexibility of the beam. Therefore the auxiliary mass can enhance the effects of the crack on the dynamics of the beam and, therefore, facilitate the identification and location of damage in the beam. That is, the auxiliary mass can be used to probe the dynamic characteristic of the beam by traversing the mass from one end of the beam to the other. However, it is impossible to obtain accurate modal frequencies by the direct operation of the fast Fourier transform (FFT) of the response data of the structure because the frequency spectrum can be only calculated from limited sampled time data which results in the well-known leakage effect. SCCM is identical to the energy centrobaric correction method (ECCM) which is a practical and effective method used in rotating mechanical fault diagnosis and which resolves the shortcoming of FFT and can provide high accuracy estimate of frequency, amplitude and phase. In the present work, the modal responses of damaged simply supported beams with auxiliary mass are computed using the finite element method (FEM). The graphical plots of the natural frequencies calculated by SCCM versus axial location of auxiliary mass are obtained. However, it is difficult to locate the crack directly from the curve of natural frequencies. A simple and fast method, the derivatives of natural frequency curve, is proposed in the paper which can provide crack information for damage detection of beam-like structures. The efficiency and practicability of the proposed method is illustrated via numerical simulation. For real cases, experimental noise is expected to corrupt the response data and, ultimately, the natural frequencies of beam-like structures. Therefore, the response data with a normally distributed random noise is also studied. Also, the effects of crack depth, auxiliary mass and damping ratios on the proposed method are investigated. From the simulated results, the efficiency and robustness of the proposed method is demonstrated. The results show that the proposed method has low computational cost and high precision.

Electrolytic Installation in Order to Obtain Deuterium and to Fill the Pressure Deposits; INSTALACION ELECTROLITICA PARA LA OBTENCION DE DEUTERIO Y LLENADO DE DEPOSITOS A PRESION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lopez, F.C.; Sanz, A.T.

1959-01-01

In order to obtain deuterium for the feed of accelerator ion sources, a sample and automatic electrolytic installation was constructed. The installation, used with a small compressor, can fill pressure vessels of 1 to 2 liter capacity with deuterium up to a pressure of 4 atmospheres in a few hours of operation. The electrolytic cell has a "V" shape and can operate with only 3 cc of heavy water. The electrodes are platinum and NaOH solution in the proportion of 15 wt.% is the electrolyte. The operation is automatic. The compressor is small, and the charge is low so thatmore » an auxiliary motor is not needed. The compressor piston is the only moving part. Deuterium losses are practically zero. (auth)« less

Solar heating and cooling systems design and development

NASA Technical Reports Server (NTRS)

1976-01-01

Solar heating and heating/cooling systems were designed for single family, multifamily, and commercial applications. Subsystems considered included solar collectors, heat storage systems, auxiliary energy sources, working fluids, and supplementary controls, piping, and pumps.

Enhanced reproducibility of L-mode plasma discharges via physics-model-based q-profile feedback control in DIII-D

NASA Astrophysics Data System (ADS)

Schuster, E.; Wehner, W. P.; Barton, J. E.; Boyer, M. D.; Luce, T. C.; Ferron, J. R.; Holcomb, C. T.; Walker, M. L.; Humphreys, D. A.; Solomon, W. M.; Penaflor, B. G.; Johnson, R. D.

2017-11-01

Recent experiments on DIII-D demonstrate the potential of physics-model-based q-profile control to improve reproducibility of plasma discharges. A combined feedforward  +  feedback control scheme is employed to optimize the current ramp-up phase by consistently achieving target q profiles (Target 1: q_min=1.3, q95=4.4 ; Target 2: q_min=1.65, q95=5.0 ; Target 3: q_min=2.1, q95=6.2 ) at prescribed times during the plasma formation phase (Target 1: t=1.5 s; Target 2: t=1.3 s; Target 3: t=1.0 s). At the core of the control scheme is a nonlinear, first-principles-driven, physics-based, control-oriented model of the plasma dynamics valid for low confinement (L-mode) scenarios. To prevent undesired L-H transitions, a constraint on the maximum allowable total auxiliary power is imposed in addition to the maximum powers for the individual heating and current-drive sources. Experimental results are presented to demonstrate the effectiveness of the combined feedforward  +  feedback control scheme to consistently achieve the desired target profiles at the predefined times. These results also show how the addition of feedback control significantly improves upon the feedforward-only control solution by reducing the matching error and also how the feedback controller is able to reduce the matching error as the constraint on the maximum allowable total auxiliary power is relaxed while keeping the plasma in L-mode.

On the adequacy of modeling the concentration dependences of the activity coefficients for the components of solutions

NASA Astrophysics Data System (ADS)

Sergievskii, V. V.; Rudakov, A. M.

2006-11-01

An analysis of the accepted methods for calculating the activity coefficients for the components of binary aqueous solutions was performed. It was demonstrated that the use of the osmotic coefficients in auxiliary calculations decreases the accuracy of estimates of the activity coefficients. The possibility of calculating the activity coefficient of the solute from the concentration dependence of the water activity was examined. It was established that, for weak electrolytes, the interpretation of data on heterogeneous equilibria within the framework of the standard assumption that the dissociation is complete encounters serious difficulties.

Suite of Benchmark Tests to Conduct Mesh-Convergence Analysis of Nonlinear and Non-constant Coefficient Transport Codes

NASA Astrophysics Data System (ADS)

Zamani, K.; Bombardelli, F. A.

2014-12-01

Verification of geophysics codes is imperative to avoid serious academic as well as practical consequences. In case that access to any given source code is not possible, the Method of Manufactured Solution (MMS) cannot be employed in code verification. In contrast, employing the Method of Exact Solution (MES) has several practical advantages. In this research, we first provide four new one-dimensional analytical solutions designed for code verification; these solutions are able to uncover the particular imperfections of the Advection-diffusion-reaction equation, such as nonlinear advection, diffusion or source terms, as well as non-constant coefficient equations. After that, we provide a solution of Burgers' equation in a novel setup. Proposed solutions satisfy the continuity of mass for the ambient flow, which is a crucial factor for coupled hydrodynamics-transport solvers. Then, we use the derived analytical solutions for code verification. To clarify gray-literature issues in the verification of transport codes, we designed a comprehensive test suite to uncover any imperfection in transport solvers via a hierarchical increase in the level of tests' complexity. The test suite includes hundreds of unit tests and system tests to check vis-a-vis the portions of the code. Examples for checking the suite start by testing a simple case of unidirectional advection; then, bidirectional advection and tidal flow and build up to nonlinear cases. We design tests to check nonlinearity in velocity, dispersivity and reactions. The concealing effect of scales (Peclet and Damkohler numbers) on the mesh-convergence study and appropriate remedies are also discussed. For the cases in which the appropriate benchmarks for mesh convergence study are not available, we utilize symmetry. Auxiliary subroutines for automation of the test suite and report generation are designed. All in all, the test package is not only a robust tool for code verification but it also provides comprehensive insight on the ADR solvers capabilities. Such information is essential for any rigorous computational modeling of ADR equation for surface/subsurface pollution transport. We also convey our experiences in finding several errors which were not detectable with routine verification techniques.

Applications of Mars Global Reference Atmospheric Model (Mars-GRAM 2005) Supporting Mission Site Selection for Mars Science Laboratory

NASA Technical Reports Server (NTRS)

Justh, Hilary L.; Justus, Carl G.

2008-01-01

The Mars Global Reference Atmospheric Model (Mars-GRAM 2005) is an engineering level atmospheric model widely used for diverse mission applications. An overview is presented of Mars-GRAM 2005 and its new features. One new feature of Mars-GRAM 2005 is the 'auxiliary profile' option. In this option, an input file of temperature and density versus altitude is used to replace mean atmospheric values from Mars-GRAM's conventional (General Circulation Model) climatology. An auxiliary profile can be generated from any source of data or alternate model output. Auxiliary profiles for this study were produced from mesoscale model output (Southwest Research Institute's Mars Regional Atmospheric Modeling System (MRAMS) model and Oregon State University's Mars mesoscale model (MMM5)model) and a global Thermal Emission Spectrometer(TES) database. The global TES database has been specifically generated for purposes of making Mars-GRAM auxiliary profiles. This data base contains averages and standard deviations of temperature, density, and thermal wind components,averaged over 5-by-5 degree latitude-longitude bins and 15 degree L(s) bins, for each of three Mars years of TES nadir data. Results are presented using auxiliary profiles produced from the mesoscale model output and TES observed data for candidate Mars Science Laboratory (MSL) landing sites. Input parameters rpscale (for density perturbations) and rwscale (for wind perturbations) can be used to "recalibrate" Mars-GRAM perturbation magnitudes to better replicate observed or mesoscale model variability.

Order-Constrained Solutions in K-Means Clustering: Even Better than Being Globally Optimal

ERIC Educational Resources Information Center

Steinley, Douglas; Hubert, Lawrence

2008-01-01

This paper proposes an order-constrained K-means cluster analysis strategy, and implements that strategy through an auxiliary quadratic assignment optimization heuristic that identifies an initial object order. A subsequent dynamic programming recursion is applied to optimally subdivide the object set subject to the order constraint. We show that…

Fuel cell system with sodium borohydride as hydrogen source for unmanned aerial vehicles

NASA Astrophysics Data System (ADS)

Kim, Kyunghwan; Kim, Taegyu; Lee, Kiseong; Kwon, Sejin

In this study, we design and fabricate a fuel cell system for application as a power source in unmanned aerial vehicles (UAVs). The fuel cell system consists of a fuel cell stack, hydrogen generator, and hybrid power management system. PEMFC stack with an output power of 100 W is prepared and tested to decide the efficient operating conditions; the stack must be operated in the dead-end mode with purge in order to ensure prolonged stack performance. A hydrogen generator is fabricated to supply gaseous hydrogen to the stack. Sodium borohydride (NaBH 4) is used as the hydrogen source in the present study. Co/Al 2O 3 catalyst is prepared for the hydrolysis of the alkaline NaBH 4 solution at room temperature. The fabricated Co catalyst is comparable to the Ru catalyst. The UAV consumes more power in the takeoff mode than in the cruising mode. A hybrid power management system using an auxiliary battery is developed and evaluated for efficient energy management. Hybrid power from both the fuel cell and battery powers takeoff and turning flight operations, while the fuel cell supplies steady power during the cruising flight. The capabilities of the fuel-cell UAVs for long endurance flights are validated by successful flight tests.

Optimizing Vetoes for Gravitational-wave Transient Searches

NASA Technical Reports Server (NTRS)

Essick, R.; Blackburn, Lindy L.; Katsavounidis, E.

2014-01-01

Interferometric gravitational-wave detectors like LIGO, GEO600 and Virgo record a surplus of information above and beyond possible gravitational-wave events. These auxiliary channels capture information about the state of the detector and its surroundings which can be used to infer potential terrestrial noise sources of some gravitational-wave-like events. We present an algorithm addressing the ordering (or equivalently optimizing) of such information from auxiliary systems in gravitational-wave detectors to establish veto conditions in searches for gravitational-wave transients. The procedure was used to identify vetoes for searches for unmodelled transients by the LIGO and Virgo collaborations during their science runs from 2005 through 2007. In this work we present the details of the algorithm; we also use a limited amount of data from LIGO's past runs in order to examine the method, compare it with other methods, and identify its potential to characterize the instruments themselves. We examine the dependence of Receiver Operating Characteristic curves on the various parameters of the veto method and the implementation on real data. We find that the method robustly determines important auxiliary channels, ordering them by the apparent strength of their correlations to the gravitational-wave channel. This list can substantially reduce the background of noise events in the gravitational-wave data. In this way it can identify the source of glitches in the detector as well as assist in establishing confidence in the detection of gravitational-wave transients.

Parareal algorithms with local time-integrators for time fractional differential equations

NASA Astrophysics Data System (ADS)

Wu, Shu-Lin; Zhou, Tao

2018-04-01

It is challenge work to design parareal algorithms for time-fractional differential equations due to the historical effect of the fractional operator. A direct extension of the classical parareal method to such equations will lead to unbalance computational time in each process. In this work, we present an efficient parareal iteration scheme to overcome this issue, by adopting two recently developed local time-integrators for time fractional operators. In both approaches, one introduces auxiliary variables to localized the fractional operator. To this end, we propose a new strategy to perform the coarse grid correction so that the auxiliary variables and the solution variable are corrected separately in a mixed pattern. It is shown that the proposed parareal algorithm admits robust rate of convergence. Numerical examples are presented to support our conclusions.

Traveling-Wave Solutions of the Kolmogorov-Petrovskii-Piskunov Equation

NASA Astrophysics Data System (ADS)

Pikulin, S. V.

2018-02-01

We consider quasi-stationary solutions of a problem without initial conditions for the Kolmogorov-Petrovskii-Piskunov (KPP) equation, which is a quasilinear parabolic one arising in the modeling of certain reaction-diffusion processes in the theory of combustion, mathematical biology, and other areas of natural sciences. A new efficiently numerically implementable analytical representation is constructed for self-similar plane traveling-wave solutions of the KPP equation with a special right-hand side. Sufficient conditions for an auxiliary function involved in this representation to be analytical for all values of its argument, including the endpoints, are obtained. Numerical results are obtained for model examples.

ADJUSTABLE OUTPUT RATE CHEMICAL FEEDING EQUIPMENT FOR SWIMMING POOLS. NATIONAL SANITATION FOUNDATION STANDARD NUMBER 19.

ERIC Educational Resources Information Center

National Sanitation Foundation, Ann Arbor, MI.

THE SCOPE OF THIS STANDARD COVERS ADJUSTABLE OUTPUT RATE CHEMICAL FEEDERS, WHETHER USED FOR SOLUTIONS, SLURRIES OR SOLIDS. IT ALSO INCLUDES AUXILIARY EQUIPMENT SUCH AS PUMPS, STRAINERS, TUBING CONNECTIONS, TANKS, INJECTION FITTINGS AND OTHER REQUIRED COMPONENTS. THE FEEDERS DESCRIBED ARE INTENDED TO BE DESIGNED AND USED SPECIFICALLY FOR CHEMICAL…

Utilizing Mars Global Reference Atmospheric Model (Mars-GRAM 2005) to Evaluate Entry Probe Mission Sites

NASA Technical Reports Server (NTRS)

Justh, Hilary L.; Justus, Carl G.

2008-01-01

The Mars Global Reference Atmospheric Model (Mars-GRAM 2005) is an engineering-level atmospheric model widely used for diverse mission applications. An overview is presented of Mars-GRAM 2005 and its new features. The "auxiliary profile" option is one new feature of Mars-GRAM 2005. This option uses an input file of temperature and density versus altitude to replace the mean atmospheric values from Mars-GRAM's conventional (General Circulation Model) climatology. Any source of data or alternate model output can be used to generate an auxiliary profile. Auxiliary profiles for this study were produced from mesoscale model output (Southwest Research Institute's Mars Regional Atmospheric Modeling System (MRAMS) model and Oregon State University's Mars mesoscale model (MMM5) model) and a global Thermal Emission Spectrometer (TES) database. The global TES database has been specifically generated for purposes of making Mars-GRAM auxiliary profiles. This data base contains averages and standard deviations of temperature, density, and thermal wind components, averaged over 5-by-5 degree latitude-longitude bins and 15 degree Ls bins, for each of three Mars years of TES nadir data. The Mars Science Laboratory (MSL) sites are used as a sample of how Mars-GRAM' could be a valuable tool for planning of future Mars entry probe missions. Results are presented using auxiliary profiles produced from the mesoscale model output and TES observed data for candidate MSL landing sites. Input parameters rpscale (for density perturbations) and rwscale (for wind perturbations) can be used to "recalibrate" Mars-GRAM perturbation magnitudes to better replicate observed or mesoscale model variability.

Incoherent transport for phases that spontaneously break translations

NASA Astrophysics Data System (ADS)

Donos, Aristomenis; Gauntlett, Jerome P.; Griffin, Tom; Ziogas, Vaios

2018-04-01

We consider phases of matter at finite charge density which spontaneously break spatial translations. Without taking a hydrodynamic limit we identify a boost invariant incoherent current operator. We also derive expressions for the small frequency behaviour of the thermoelectric conductivities generalising those that have been derived in a translationally invariant context. Within holographic constructions we show that the DC conductivity for the incoherent current can be obtained from a solution to a Stokes flow for an auxiliary fluid on the black hole horizon combined with specific thermodynamic quantities associated with the equilibrium black hole solutions.

Scaling Symmetries in Elastic-Plastic Dynamic Cavity Expansion Equations Using the Isovector Method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Albright, Eric Jason; Ramsey, Scott D.; Schmidt, Joseph H.

Cavity-expansion approximations are widely-used in the study of penetration mechanics and indentation phenomena. We apply the isovector method to a well-established model in the literature for elastic-plastic cavity-expansion to systematically demonstrate the existence of Lie symmetries corresponding to scale-invariant solutions. Here we use the symmetries obtained from the equations of motion to determine compatible auxiliary conditions describing the cavity wall trajectory and the elastic-plastic material interface. The admissible conditions are then compared with specific similarity solutions in the literature.

Scaling Symmetries in Elastic-Plastic Dynamic Cavity Expansion Equations Using the Isovector Method

DOE PAGES

Albright, Eric Jason; Ramsey, Scott D.; Schmidt, Joseph H.; ...

2017-09-16

Cavity-expansion approximations are widely-used in the study of penetration mechanics and indentation phenomena. We apply the isovector method to a well-established model in the literature for elastic-plastic cavity-expansion to systematically demonstrate the existence of Lie symmetries corresponding to scale-invariant solutions. Here we use the symmetries obtained from the equations of motion to determine compatible auxiliary conditions describing the cavity wall trajectory and the elastic-plastic material interface. The admissible conditions are then compared with specific similarity solutions in the literature.

Spectrally and Radiometrically Stable, Wideband, Onboard Calibration Source

NASA Technical Reports Server (NTRS)

Coles, James B.; Richardson, Brandon S.; Eastwood, Michael L.; Sarture, Charles M.; Quetin, Gregory R.; Porter, Michael D.; Green, Robert O.; Nolte, Scott H.; Hernandez, Marco A.; Knoll, Linley A.

2013-01-01

The Onboard Calibration (OBC) source incorporates a medical/scientific-grade halogen source with a precisely designed fiber coupling system, and a fiber-based intensity-monitoring feedback loop that results in radiometric and spectral stabilities to within less than 0.3 percent over a 15-hour period. The airborne imaging spectrometer systems developed at the Jet Propulsion Laboratory incorporate OBC sources to provide auxiliary in-use system calibration data. The use of the OBC source will provide a significant increase in the quantitative accuracy, reliability, and resulting utility of the spectral data collected from current and future imaging spectrometer instruments.

Efficient evaluation of the Coulomb force in the Gaussian and finite-element Coulomb method.

PubMed

Kurashige, Yuki; Nakajima, Takahito; Sato, Takeshi; Hirao, Kimihiko

2010-06-28

We propose an efficient method for evaluating the Coulomb force in the Gaussian and finite-element Coulomb (GFC) method, which is a linear-scaling approach for evaluating the Coulomb matrix and energy in large molecular systems. The efficient evaluation of the analytical gradient in the GFC is not straightforward as well as the evaluation of the energy because the SCF procedure with the Coulomb matrix does not give a variational solution for the Coulomb energy. Thus, an efficient approximate method is alternatively proposed, in which the Coulomb potential is expanded in the Gaussian and finite-element auxiliary functions as done in the GFC. To minimize the error in the gradient not just in the energy, the derived functions of the original auxiliary functions of the GFC are used additionally for the evaluation of the Coulomb gradient. In fact, the use of the derived functions significantly improves the accuracy of this approach. Although these additional auxiliary functions enlarge the size of the discretized Poisson equation and thereby increase the computational cost, it maintains the near linear scaling as the GFC and does not affects the overall efficiency of the GFC approach.

Enhanced reproducibility of L-mode plasma discharges via physics-model-based q-profile feedback control in DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schuster, Eugenio J.; Wehner, William P.; Barton, Joseph E.

Recent experiments on DIII-D demonstrate the potential of physics-model-based q-profile control to improve reproducibility of plasma discharges. A combined feed forward + feedback control scheme is employed to optimize the current ramp-up phase by consistently achieving target q profiles (Target 1: q min = 1.3,q 95 = 4:4; Target 2: q min = 1.65,q 95 = 5.0; Target 3: q min = 2.1,q 95 = 6:2) at prescribed times during the plasma formation phase (Target 1: t = 1.5 s; Target 2: t = 1:3 s; Target 3: t = 1.0 s). At the core of the control scheme ismore » a nonlinear, first-principles-driven, physics-based, control-oriented model of the plasma dynamics valid for low confinement (L-mode) scenarios. To prevent undesired L-H transitions, a constraint on the maximum allowable total auxiliary power is imposed in addition to the maximum powers for the individual heating and current-drive sources. Experimental results are presented to demonstrate the effectiveness of the combined feed forward + feedback control scheme to consistently achieve the desired target profiles at the predefined times. Here, these results also show how the addition of feedback control significantly improves upon the feed forward only control solution by reducing the matching error and also how the feedback controller is able to reduce the matching error as the constraint on the maximum allowable total auxiliary power is relaxed while keeping the plasma in L-mode.« less

Enhanced reproducibility of L-mode plasma discharges via physics-model-based q-profile feedback control in DIII-D

DOE PAGES

Schuster, Eugenio J.; Wehner, William P.; Barton, Joseph E.; ...

2017-08-09

Recent experiments on DIII-D demonstrate the potential of physics-model-based q-profile control to improve reproducibility of plasma discharges. A combined feed forward + feedback control scheme is employed to optimize the current ramp-up phase by consistently achieving target q profiles (Target 1: q min = 1.3,q 95 = 4:4; Target 2: q min = 1.65,q 95 = 5.0; Target 3: q min = 2.1,q 95 = 6:2) at prescribed times during the plasma formation phase (Target 1: t = 1.5 s; Target 2: t = 1:3 s; Target 3: t = 1.0 s). At the core of the control scheme ismore » a nonlinear, first-principles-driven, physics-based, control-oriented model of the plasma dynamics valid for low confinement (L-mode) scenarios. To prevent undesired L-H transitions, a constraint on the maximum allowable total auxiliary power is imposed in addition to the maximum powers for the individual heating and current-drive sources. Experimental results are presented to demonstrate the effectiveness of the combined feed forward + feedback control scheme to consistently achieve the desired target profiles at the predefined times. Here, these results also show how the addition of feedback control significantly improves upon the feed forward only control solution by reducing the matching error and also how the feedback controller is able to reduce the matching error as the constraint on the maximum allowable total auxiliary power is relaxed while keeping the plasma in L-mode.« less

Mesh refinement and numerical sensitivity analysis for parameter calibration of partial differential equations

NASA Astrophysics Data System (ADS)

Becker, Roland; Vexler, Boris

2005-06-01

We consider the calibration of parameters in physical models described by partial differential equations. This task is formulated as a constrained optimization problem with a cost functional of least squares type using information obtained from measurements. An important issue in the numerical solution of this type of problem is the control of the errors introduced, first, by discretization of the equations describing the physical model, and second, by measurement errors or other perturbations. Our strategy is as follows: we suppose that the user defines an interest functional I, which might depend on both the state variable and the parameters and which represents the goal of the computation. First, we propose an a posteriori error estimator which measures the error with respect to this functional. This error estimator is used in an adaptive algorithm to construct economic meshes by local mesh refinement. The proposed estimator requires the solution of an auxiliary linear equation. Second, we address the question of sensitivity. Applying similar techniques as before, we derive quantities which describe the influence of small changes in the measurements on the value of the interest functional. These numbers, which we call relative condition numbers, give additional information on the problem under consideration. They can be computed by means of the solution of the auxiliary problem determined before. Finally, we demonstrate our approach at hand of a parameter calibration problem for a model flow problem.

Theoretical evaluation of engine auxiliary inlet design for supersonic V/STOL aircraft

NASA Technical Reports Server (NTRS)

Boles, Michael A.; Heavner, Richard L.

1988-01-01

A higher order panel method is used to evaluate the potential flow of a two dimensional supersonic V/STOL inlet. A non-symmetric analytical inlet model is developed to closely match a wind tunnel model. The analytical inlet is analyzed for flow characteristics around the lower cowl lip and auxiliary inlets. The results are obtained from the output of a computer program that is based on the Hess Panel Method which determines source strengths of panels distributed over a three dimensional body. The analytical model was designed for the implementation of drooped/translated cowl lip and auxiliary inlets as flow improvement concepts. A 40 or 70 degree droop lip can be incorporated on the inlet to determine if these geometry modifications result in flow improvements which may reduce the propensity for flow separation on the interior portion of the lip. Auxiliary inlets are employed to decrease the mass flow over the inlet lip. Thus, the peak flow velocity is reduced at the lip which also lessens the likelihood of flow separation on the interior portion of the lip. A 2, 4, and 6 inch translated lip can be employed to also decrease mass flow over the inlet lower lip in the same manner as the auxiliary inlet. The performance results of the flow improvement concepts show that three possible inlet configurations provide a situation where separation is less likely to occur. A 70 degree droop lip maintains flow conditions such that attached flow over the lower cowl lip may exist for the entire angle of attack range studied. A 0 degree droop and translated lip combination provides similar results for the angle of attack range. The third configuration consists of a 0 degree droop and auxiliary inlet combination. This configuration provides slightly less favorable results than the other two, but still allows for conditions favorable to attached flow within the inlet.

Impact of quasar proper motions on the alignment between the International Celestial Reference Frame and the Gaia reference frame

NASA Astrophysics Data System (ADS)

Liu, J.-C.; Malkin, Z.; Zhu, Z.

2018-03-01

The International Celestial Reference Frame (ICRF) is currently realized by the very long baseline interferometry (VLBI) observations of extragalactic sources with the zero proper motion assumption, while Gaia will observe proper motions of these distant and faint objects to an accuracy of tens of microarcseconds per year. This paper investigates the difference between VLBI and Gaia quasar proper motions and it aims to understand the impact of quasar proper motions on the alignment of the ICRF and Gaia reference frame. We use the latest time series data of source coordinates from the International VLBI Service analysis centres operated at Goddard Space Flight Center (GSF2017) and Paris observatory (OPA2017), as well as the Gaia auxiliary quasar solution containing 2191 high-probability optical counterparts of the ICRF2 sources. The linear proper motions in right ascension and declination of VLBI sources are derived by least-squares fits while the proper motions for Gaia sources are simulated taking into account the acceleration of the Solar system barycentre and realistic uncertainties depending on the source brightness. The individual and global features of source proper motions in GSF2017 and OPA2017 VLBI data are found to be inconsistent, which may result from differences in VLBI observations, data reduction and analysis. A comparison of the VLBI and Gaia proper motions shows that the accuracies of the components of rotation and glide between the two systems are 2-4 μas yr- 1 based on about 600 common sources. For the future alignment of the ICRF and Gaia reference frames at different wavelengths, the proper motions of quasars must necessarily be considered.

47 CFR 74.6 - Licensing of broadcast auxiliary and low power auxiliary stations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Licensing of broadcast auxiliary and low power... low power auxiliary stations. Applicants for and licensees of remote pickup broadcast stations, aural broadcast auxiliary stations, television broadcast auxiliary stations, and low power auxiliary stations...

Intelligent Vehicle Power Management Using Machine Learning and Fuzzy Logic

DTIC Science & Technology

2008-06-01

batteries of similar physical size. An ultracapacitor can receive regenerative energy and give power during peak periods. Moreno et al. proposed to...use an ultracapacitor as an auxiliary energy system in combination with a primary source that is unable to accept energy from the regenerative ... braking [22]. There are other power sources that are being considered in HEV research [20-22] and future vehicle systems may use combinations of

BOREAS RSS-4 1994 Jack Pine Leaf Biochemistry and Modeled Spectra in the SSA

NASA Technical Reports Server (NTRS)

Hall, Forrest G. (Editor); Nickeson, Jaime (Editor); Plummer, Stephen; Lucas, Neil; Dawson, Terry

2000-01-01

The BOREAS RSS-4 team focused its efforts on deriving estimates of LAI and leaf chlorophyll and nitrogen concentrations from remotely sensed data for input into the Forest BGC model. This data set contains measurements of jack pine (Pinus banksiana) needle biochemistry from the BOREAS SSA in July and August 1994. The data contain measurements of current and year-1 needle chlorophyll, nitrogen, lignin, cellulose, and water content for the OJP flux tower and nearby auxiliary sites. The data have been used to test a needle reflectance and transmittance model, LIBERTY (Dawson et al., in press). The source code for the model and modeled needle spectra for each of the sampled tower and auxiliary sites are provided as part of this data set. The LIBERTY model was developed and the predicted spectral data generated to parameterize a canopy reflectance model (North, 1996) for comparison with AVIRIS, POLDER, and PARABOLA data. The data and model source code are stored in ASCII files.

A high-resolution 7-Tesla fMRI dataset from complex natural stimulation with an audio movie.

PubMed

Hanke, Michael; Baumgartner, Florian J; Ibe, Pierre; Kaule, Falko R; Pollmann, Stefan; Speck, Oliver; Zinke, Wolf; Stadler, Jörg

2014-01-01

Here we present a high-resolution functional magnetic resonance (fMRI) dataset - 20 participants recorded at high field strength (7 Tesla) during prolonged stimulation with an auditory feature film ("Forrest Gump"). In addition, a comprehensive set of auxiliary data (T1w, T2w, DTI, susceptibility-weighted image, angiography) as well as measurements to assess technical and physiological noise components have been acquired. An initial analysis confirms that these data can be used to study common and idiosyncratic brain response patterns to complex auditory stimulation. Among the potential uses of this dataset are the study of auditory attention and cognition, language and music perception, and social perception. The auxiliary measurements enable a large variety of additional analysis strategies that relate functional response patterns to structural properties of the brain. Alongside the acquired data, we provide source code and detailed information on all employed procedures - from stimulus creation to data analysis. In order to facilitate replicative and derived works, only free and open-source software was utilized.

The Innovative Design and Prototype Verification of Wheelchair with One Degree of Freedom to Perform Lifting and Standing Functions

NASA Astrophysics Data System (ADS)

Hsieh, Long-Chang; Chen, Tzu-Hsia

2017-12-01

Traditionally, the mechanism of wheelchair with lifting and standing functions has 2 degrees of freedom, and used 2 power sources to perform these 2 motion function. The purpose of this paper is to invent new wheelchair with 1 degree of freedom to perform these 2 motion functions. Hence, we can use only 1 power source to drive the mechanism to achieve lifting and standing motion functions. The new design has the advantages of simple operation, more stability, and more safety. For traditional standing wheelchair, its’ centre of gravity moves forward when standing up and it needs 2 auxiliary wheels to prevent dumping. In this paper, by using the checklist method of Osborn, the wheelchair with 1 DOF is invented to perform lifting and standing functions. The centre of gravity of this new wheelchair after standing up still located between the front and rear wheels, no auxiliary wheels needed. Finally, the prototype is manufactured to verify the theoretical results.

Corrigendum to “A new hyperbolic auxiliary function method and exact solutions of the mBBM equation” [Commun Nonlinear Sci Numer Simul 2010;15:135-138

NASA Astrophysics Data System (ADS)

Layeni, Olawanle P.; Akinola, Ade P.

2010-09-01

The symbols w and ω were abused in article [1]. Replacing ξ + ω with ξ throughout the article (that is in Eqs. (5) and (13)-(23)) and afterwards taking w and ω to denote the (same) frequency of the traveling wave(s) set this right.

Differential geometry techniques for sets of nonlinear partial differential equations

NASA Technical Reports Server (NTRS)

Estabrook, Frank B.

1990-01-01

An attempt is made to show that the Cartan theory of partial differential equations can be a useful technique for applied mathematics. Techniques for finding consistent subfamilies of solutions that are generically rich and well-posed and for introducing potentials or other usefully consistent auxiliary fields are introduced. An extended sample calculation involving the Korteweg-de Vries equation is given.

Application of Machine Learning Algorithms to the Study of Noise Artifacts in Gravitational-Wave Data

NASA Technical Reports Server (NTRS)

Biswas, Rahul; Blackburn, Lindy L.; Cao, Junwei; Essick, Reed; Hodge, Kari Alison; Katsavounidis, Erotokritos; Kim, Kyungmin; Young-Min, Kim; Le Bigot, Eric-Olivier; Lee, Chang-Hwan;

Travelling-wave solutions of a weakly nonlinear two-dimensional higher-order Kadomtsev-Petviashvili dynamical equation for dispersive shallow-water waves

NASA Astrophysics Data System (ADS)

Seadawy, Aly R.

2017-01-01

The propagation of three-dimensional nonlinear irrotational flow of an inviscid and incompressible fluid of the long waves in dispersive shallow-water approximation is analyzed. The problem formulation of the long waves in dispersive shallow-water approximation lead to fifth-order Kadomtsev-Petviashvili (KP) dynamical equation by applying the reductive perturbation theory. By using an extended auxiliary equation method, the solitary travelling-wave solutions of the two-dimensional nonlinear fifth-order KP dynamical equation are derived. An analytical as well as a numerical solution of the two-dimensional nonlinear KP equation are obtained and analyzed with the effects of external pressure flow.

Big power from walking

NASA Astrophysics Data System (ADS)

Illenberger, Patrin K.; Madawala, Udaya K.; Anderson, Iain A.

2016-04-01

Dielectric Elastomer Generators (DEG) offer an opportunity to capture the energy otherwise wasted from human motion. By integrating a DEG into the heel of standard footwear, it is possible to harness this energy to power portable devices. DEGs require substantial auxiliary systems which are commonly large, heavy and inefficient. A unique challenge for these low power generators is the combination of high voltage and low current. A void exists in the semiconductor market for devices that can meet these requirements. Until these become available, existing devices must be used in an innovative way to produce an effective DEG system. Existing systems such as the Bi-Directional Flyback (BDFB) and Self Priming Circuit (SPC) are an excellent example of this. The BDFB allows full charging and discharging of the DEG, improving power gained. The SPC allows fully passive voltage boosting, removing the priming source and simplifying the electronics. This paper outlines the drawbacks and benefits of active and passive electronic solutions for maximizing power from walking.

Exposure calculation code module for reactor core analysis: BURNER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vondy, D.R.; Cunningham, G.W.

1979-02-01

The code module BURNER for nuclear reactor exposure calculations is presented. The computer requirements are shown, as are the reference data and interface data file requirements, and the programmed equations and procedure of calculation are described. The operating history of a reactor is followed over the period between solutions of the space, energy neutronics problem. The end-of-period nuclide concentrations are determined given the necessary information. A steady state, continuous fueling model is treated in addition to the usual fixed fuel model. The control options provide flexibility to select among an unusually wide variety of programmed procedures. The code also providesmore » user option to make a number of auxiliary calculations and print such information as the local gamma source, cumulative exposure, and a fine scale power density distribution in a selected zone. The code is used locally in a system for computation which contains the VENTURE diffusion theory neutronics code and other modules.« less

Tail mean and related robust solution concepts

NASA Astrophysics Data System (ADS)

Ogryczak, Włodzimierz

2014-01-01

Robust optimisation might be viewed as a multicriteria optimisation problem where objectives correspond to the scenarios although their probabilities are unknown or imprecise. The simplest robust solution concept represents a conservative approach focused on the worst-case scenario results optimisation. A softer concept allows one to optimise the tail mean thus combining performances under multiple worst scenarios. We show that while considering robust models allowing the probabilities to vary only within given intervals, the tail mean represents the robust solution for only upper bounded probabilities. For any arbitrary intervals of probabilities the corresponding robust solution may be expressed by the optimisation of appropriately combined mean and tail mean criteria thus remaining easily implementable with auxiliary linear inequalities. Moreover, we use the tail mean concept to develope linear programming implementable robust solution concepts related to risk averse optimisation criteria.

46 CFR 112.50-7 - Compressed air starting.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Diesel and Gas Turbine Engine Driven Generator Sets § 112.50-7 Compressed... emergency power source. If this compressor supplies other auxiliaries, there must be a non-return valve at...

Long-Life/Low-Power Ion-Gun Cathode

NASA Technical Reports Server (NTRS)

Fitzgerald, D. J.

1982-01-01

New cathode has form of hollow tube through which gas enters region of high electron density, produced by electric discharge with auxiliary electrode referred to as "keeper." Ion-gun cathode emits electrons that bombard gas in chamber. Ions accelerated out of source are used to dope semiconductor material.

Crystallographic snapshots of sulfur insertion by lipoyl synthase

PubMed Central

McLaughlin, Martin I.; Lanz, Nicholas D.; Goldman, Peter J.; Lee, Kyung-Hoon; Booker, Squire J.; Drennan, Catherine L.

2016-01-01

Lipoyl synthase (LipA) catalyzes the insertion of two sulfur atoms at the unactivated C6 and C8 positions of a protein-bound octanoyl chain to produce the lipoyl cofactor. To activate its substrate for sulfur insertion, LipA uses a [4Fe-4S] cluster and S-adenosylmethionine (AdoMet) radical chemistry; the remainder of the reaction mechanism, especially the source of the sulfur, has been less clear. One controversial proposal involves the removal of sulfur from a second (auxiliary) [4Fe-4S] cluster on the enzyme, resulting in destruction of the cluster during each round of catalysis. Here, we present two high-resolution crystal structures of LipA from Mycobacterium tuberculosis: one in its resting state and one at an intermediate state during turnover. In the resting state, an auxiliary [4Fe-4S] cluster has an unusual serine ligation to one of the irons. After reaction with an octanoyllysine-containing 8-mer peptide substrate and 1 eq AdoMet, conditions that allow for the first sulfur insertion but not the second insertion, the serine ligand dissociates from the cluster, the iron ion is lost, and a sulfur atom that is still part of the cluster becomes covalently attached to C6 of the octanoyl substrate. This intermediate structure provides a clear picture of iron–sulfur cluster destruction in action, supporting the role of the auxiliary cluster as the sulfur source in the LipA reaction and describing a radical strategy for sulfur incorporation into completely unactivated substrates. PMID:27506792

A robust control strategy for mitigating renewable energy fluctuations in a real hybrid power system combined with SMES

NASA Astrophysics Data System (ADS)

Magdy, G.; Shabib, G.; Elbaset, Adel A.; Qudaih, Yaser; Mitani, Yasunori

2018-05-01

Utilizing Renewable Energy Sources (RESs) is attracting great attention as a solution to future energy shortages. However, the irregular nature of RESs and random load deviations cause a large frequency and voltage fluctuations. Therefore, in order to benefit from a maximum capacity of the RESs, a robust mitigation strategy of power fluctuations from RESs must be applied. Hence, this paper proposes a design of Load Frequency Control (LFC) coordinated with Superconducting Magnetic Energy Storage (SMES) technology (i.e., an auxiliary LFC), using an optimal PID controller-based Particle Swarm Optimization (PSO) in the Egyptian Power System (EPS) considering high penetration of Photovoltaics (PV) power generation. Thus, from the perspective of LFC, the robust control strategy is proposed to maintain the nominal system frequency and mitigating the power fluctuations from RESs against all disturbances sources for the EPS with the multi-source environment. The EPS is decomposed into three dynamics subsystems, which are non-reheat, reheat and hydro power plants taking into consideration the system nonlinearity. The results by nonlinear simulation Matlab/Simulink for the EPS combined with SMES system considering PV solar power approves that, the proposed control strategy achieves a robust stability by reducing transient time, minimizing the frequency deviations, maintaining the system frequency, preventing conventional generators from exceeding their power ratings during load disturbances, and mitigating the power fluctuations from the RESs.

A Map/INS/Wi-Fi Integrated System for Indoor Location-Based Service Applications

PubMed Central

Yu, Chunyang; Lan, Haiyu; Gu, Fuqiang; Yu, Fei; El-Sheimy, Naser

2017-01-01

In this research, a new Map/INS/Wi-Fi integrated system for indoor location-based service (LBS) applications based on a cascaded Particle/Kalman filter framework structure is proposed. Two-dimension indoor map information, together with measurements from an inertial measurement unit (IMU) and Received Signal Strength Indicator (RSSI) value, are integrated for estimating positioning information. The main challenge of this research is how to make effective use of various measurements that complement each other in order to obtain an accurate, continuous, and low-cost position solution without increasing the computational burden of the system. Therefore, to eliminate the cumulative drift caused by low-cost IMU sensor errors, the ubiquitous Wi-Fi signal and non-holonomic constraints are rationally used to correct the IMU-derived navigation solution through the extended Kalman Filter (EKF). Moreover, the map-aiding method and map-matching method are innovatively combined to constrain the primary Wi-Fi/IMU-derived position through an Auxiliary Value Particle Filter (AVPF). Different sources of information are incorporated through a cascaded structure EKF/AVPF filter algorithm. Indoor tests show that the proposed method can effectively reduce the accumulation of positioning errors of a stand-alone Inertial Navigation System (INS), and provide a stable, continuous and reliable indoor location service. PMID:28574471

A Map/INS/Wi-Fi Integrated System for Indoor Location-Based Service Applications.

PubMed

Yu, Chunyang; Lan, Haiyu; Gu, Fuqiang; Yu, Fei; El-Sheimy, Naser

2017-06-02

In this research, a new Map/INS/Wi-Fi integrated system for indoor location-based service (LBS) applications based on a cascaded Particle/Kalman filter framework structure is proposed. Two-dimension indoor map information, together with measurements from an inertial measurement unit (IMU) and Received Signal Strength Indicator (RSSI) value, are integrated for estimating positioning information. The main challenge of this research is how to make effective use of various measurements that complement each other in order to obtain an accurate, continuous, and low-cost position solution without increasing the computational burden of the system. Therefore, to eliminate the cumulative drift caused by low-cost IMU sensor errors, the ubiquitous Wi-Fi signal and non-holonomic constraints are rationally used to correct the IMU-derived navigation solution through the extended Kalman Filter (EKF). Moreover, the map-aiding method and map-matching method are innovatively combined to constrain the primary Wi-Fi/IMU-derived position through an Auxiliary Value Particle Filter (AVPF). Different sources of information are incorporated through a cascaded structure EKF/AVPF filter algorithm. Indoor tests show that the proposed method can effectively reduce the accumulation of positioning errors of a stand-alone Inertial Navigation System (INS), and provide a stable, continuous and reliable indoor location service.

Near-term hybrid vehicle program, phase 1. Appendix B: Design trade-off studies report. Volume 2: Supplement to design trade-off studies

NASA Technical Reports Server (NTRS)

1979-01-01

Results of studies leading to the preliminary design of a hybrid passenger vehicle which is projected to have the maximum potential for reducing petroleum consumption in the near term are presented. Heat engine/electric hybrid vehicle tradeoffs, assessment of battery power source, and weight and cost analysis of key components are among the topics covered. Performance of auxiliary equipment, such as power steering, power brakes, air conditioning, lighting and electrical accessories, heating and ventilation is discussed along with the selection of preferred passenger compartment heating procedure for the hybrid vehicle. Waste heat from the engine, thermal energy storage, and an auxiliary burner are among the approaches considered.

76 FR 70377 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-14

... auxiliary fuel tanks. This proposed AD was prompted by fuel system reviews conducted by the manufacturer... systems. As a result of those findings, we issued a regulation titled ``Transport Airplane Fuel Tank... fuel tank systems can prevent ignition sources in the fuel tanks. This requirement applies to type...

Teaching Techniques for Accessory Percussion

ERIC Educational Resources Information Center

Micallef, Ken

2007-01-01

Everyone is familiar with the main percussion instruments of the contemporary orchestra: bass drum, snare drum, suspended cymbal, vibraphone, and timpani. But as source material broadens, so do the demands placed on the percussion section. Accessory, or auxiliary percussion, can make the difference between a typical rendition of a well-known piece…

Power from Radioisotopes, Understanding the Atom Series.

ERIC Educational Resources Information Center

Corliss, William R.; Mead, Robert L.

This 1971 revision deals with radioisotopes and their use in power generators. Early developments and applications for the Systems for Nuclear Auxiliary Power (SNAP) and Radioisotope Thermoelectric Generators (RTGs) are reviewed. Present uses in space and on earth are included. Uses in space are as power sources in various satellites and space…

Twelve solar-heating/cooling systems: Design and development

NASA Technical Reports Server (NTRS)

1980-01-01

Two quarterly reports describe first 6 months of development on single family, multifamily, and commercial installations in Minneapolis area. Reports discuss basic requirements, and reasons for selecting specific configurations. Systems consist of liquid cooled flat plate collectors, two fluid loops, and gas-fired forced-air auxiliary heat source.

Electromagnetic Induction Sensing of UneXploded Ordnance with Pedemis

DTIC Science & Technology

2012-10-22

Pasion , L. R., “A unified approach to uxo discrimination using the method of auxiliary sources,” tech. rep. (2006). [19] Barrowes, B. E., O’Neill, K...inversion and classification using advanced emi models,” (2010). SERDP-MR-1572. [27] Pasion , L., “Uxo discrimination using full coverage and cued

The Promise of Partnerships: Researchers Join Forces with Educators to Solve Problems of Practice of Partnerships

ERIC Educational Resources Information Center

Meister, Gail R.; Blitz, Cynthia L.

2016-01-01

An auxiliary and potentially powerful source of practitioners' knowledge, skills, and dispositions can come from participation in research-practice partnerships. Research-practice partnerships link researchers, usually faculty at institutions of higher education, with practitioners working in schools, district central offices, county offices, or…

46 CFR 63.25-1 - Small automatic auxiliary boilers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Small automatic auxiliary boilers. 63.25-1 Section 63.25... AUXILIARY BOILERS Requirements for Specific Types of Automatic Auxiliary Boilers § 63.25-1 Small automatic auxiliary boilers. Small automatic auxiliary boilers defined as having heat-input ratings of 400,000 Btu/hr...

78 FR 12809 - Buy America Waiver Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-25

... steel products in (1) Auxiliary two speed motor, (2) Auxiliary back up drive clutch, (3) Main span and... appropriate to use some non-domestic iron and steel products in (1) Auxiliary two speed motor, (2) Auxiliary... steel products in (1) Auxiliary two speed motor, (2) Auxiliary back up drive clutch, (3) Main span and...

[Links between non-professional agents and the official Veterinary Services in sub-Saharan Africa].

PubMed

Diop, B A; Bessin, R

2004-04-01

Para-professional agents known as auxiliaries, or community animal health workers, provide low-cost basic veterinary services to communities of livestock producers. A 2003 survey of 16 Sub-Saharan African countries, carried out as part of the Pan-African Programme for the Control of Epizootics, showed that in the majority of cases, the official Veterinary Services have no (or very few) links with the auxiliaries, although they are well aware of their existence and in some cases the auxiliaries have been trained by officials of the Veterinary Services. However, there are isolated cases of countries establishing more formal links, for example, recognising the status of an auxiliary, recognising auxiliaries with no definition of a status, attaching auxiliaries to Veterinary Service staff, establishing agreements for the provision of auxiliary services through livestock producer associations, harmonising auxiliary training programmes, issuing professional auxiliary cards, and setting up a consultation framework on the issue of auxiliaries. Unlike private veterinarians, agents of the official services do not generally perceive auxiliaries as competitors, and sometimes collaboration develops at this level. The authors propose several measures to improve links between the official Veterinary Services and auxiliaries, as follows: the fields of competence of auxiliaries should be defined and their curriculum harmonised, the status of auxiliaries should be recognised, a monitoring and assessment mechanism should be established at senior level in the Veterinary Services, training for livestock producers should be improved.

Coherent states formulation of polymer field theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Man, Xingkun; Villet, Michael C.; Materials Research Laboratory, University of California, Santa Barbara, California 93106

2014-01-14

We introduce a stable and efficient complex Langevin (CL) scheme to enable the first direct numerical simulations of the coherent-states (CS) formulation of polymer field theory. In contrast with Edwards’ well-known auxiliary-field (AF) framework, the CS formulation does not contain an embedded nonlinear, non-local, implicit functional of the auxiliary fields, and the action of the field theory has a fully explicit, semi-local, and finite-order polynomial character. In the context of a polymer solution model, we demonstrate that the new CS-CL dynamical scheme for sampling fluctuations in the space of coherent states yields results in good agreement with now-standard AF-CL simulations.more » The formalism is potentially applicable to a broad range of polymer architectures and may facilitate systematic generation of trial actions for use in coarse-graining and numerical renormalization-group studies.« less

47 CFR 74.1290 - FM translator and booster station information available on the Internet.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transmissions, Permissible (Low Power Auxiliaries) 74.831 Transmitter power (Remote Pickup) 74.461 Transmitters... equipment— Aural Auxiliary 74.550 Remote Pickup 74.451 TV Auxiliaries 74.655 Lw Power Auxiliaries 74.851... stations 74.537 Remote Pickup 74.433 TV Auxiliaries 74.633 Low Power Auxiliaries 74.833 Authorized emission...

Carbon Nanotube Thread Electrochemical Cell: Detection of Heavy Metals.

PubMed

Zhao, Daoli; Siebold, David; Alvarez, Noe T; Shanov, Vesselin N; Heineman, William R

2017-09-19

In this work, all three electrodes in an electrochemical cell were fabricated based on carbon nanotube (CNT) thread. CNT thread partially insulated with a thin polystyrene coating to define the microelectrode area was used as the working electrode; bare CNT thread was used as the auxiliary electrode; and a micro quasi-reference electrode was fabricated by electroplating CNT thread with Ag and then anodizing it in chloride solution to form a layer of AgCl. The Ag|AgCl coated CNT thread electrode provided a stable potential comparable to the conventional liquid-junction type Ag|AgCl reference electrode. The CNT thread auxiliary electrode provided a stable current, which is comparable to a Pt wire auxiliary electrode. This all-CNT thread three electrode cell has been evaluated as a microsensor for the simultaneous determination of trace levels of heavy metal ions by anodic stripping voltammetry (ASV). Hg 2+ , Cu 2+ , and Pb 2+ were used as a representative system for this study. The calculated detection limits (based on the 3σ method) with a 120 s deposition time are 1.05, 0.53, and 0.57 nM for Hg 2+ , Cu 2+ , and Pb 2+ , respectively. These electrodes significantly reduce the dimensions of the conventional three electrode electrochemical cell to the microscale.

DEEP WIDEBAND SINGLE POINTINGS AND MOSAICS IN RADIO INTERFEROMETRY: HOW ACCURATELY DO WE RECONSTRUCT INTENSITIES AND SPECTRAL INDICES OF FAINT SOURCES?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rau, U.; Bhatnagar, S.; Owen, F. N., E-mail: rurvashi@nrao.edu

Many deep wideband wide-field radio interferometric surveys are being designed to accurately measure intensities, spectral indices, and polarization properties of faint source populations. In this paper, we compare various wideband imaging methods to evaluate the accuracy to which intensities and spectral indices of sources close to the confusion limit can be reconstructed. We simulated a wideband single-pointing (C-array, L-Band (1–2 GHz)) and 46-pointing mosaic (D-array, C-Band (4–8 GHz)) JVLA observation using a realistic brightness distribution ranging from 1 μ Jy to 100 mJy and time-, frequency-, polarization-, and direction-dependent instrumental effects. The main results from these comparisons are (a) errors in themore » reconstructed intensities and spectral indices are larger for weaker sources even in the absence of simulated noise, (b) errors are systematically lower for joint reconstruction methods (such as Multi-Term Multi-Frequency-Synthesis (MT-MFS)) along with A-Projection for accurate primary beam correction, and (c) use of MT-MFS for image reconstruction eliminates Clean-bias (which is present otherwise). Auxiliary tests include solutions for deficiencies of data partitioning methods (e.g., the use of masks to remove clean bias and hybrid methods to remove sidelobes from sources left un-deconvolved), the effect of sources not at pixel centers, and the consequences of various other numerical approximations within software implementations. This paper also demonstrates the level of detail at which such simulations must be done in order to reflect reality, enable one to systematically identify specific reasons for every trend that is observed, and to estimate scientifically defensible imaging performance metrics and the associated computational complexity of the algorithms/analysis procedures.« less

A mixed-mode crack analysis of isotropic solids using conservation laws of elasticity

NASA Technical Reports Server (NTRS)

Yau, J. F.; Wang, S. S.; Corten, H. T.

1980-01-01

A simple and convenient method of analysis for studying two-dimensional mixed-mode crack problems is presented. The analysis is formulated on the basis of conservation laws of elasticity and of fundamental relationships in fracture mechanics. The problem is reduced to the determination of mixed-mode stress-intensity factor solutions in terms of conservation integrals involving known auxiliary solutions. One of the salient features of the present analysis is that the stress-intensity solutions can be determined directly by using information extracted in the far field. Several examples with solutions available in the literature are solved to examine the accuracy and other characteristics of the current approach. This method is demonstrated to be superior in its numerical simplicity and computational efficiency to other approaches. Solutions of more complicated and practical engineering fracture problems dealing with the crack emanating from a circular hole are presented also to illustrate the capacity of this method

Breakdown voltage reliability improvement in gas-discharge tube surge protectors employing graphite field emitters

NASA Astrophysics Data System (ADS)

Žumer, Marko; Zajec, Bojan; Rozman, Robert; Nemanič, Vincenc

2012-04-01

Gas-discharge tube (GDT) surge protectors are known for many decades as passive units used in low-voltage telecom networks for protection of electrical components from transient over-voltages (discharging) such as lightning. Unreliability of the mean turn-on DC breakdown voltage and the run-to-run variability has been overcome successfully in the past by adding, for example, a radioactive source inside the tube. Radioisotopes provide a constant low level of free electrons, which trigger the breakdown. In the last decades, any concept using environmentally harmful compounds is not acceptable anymore and new solutions were searched. In our application, a cold field electron emitter source is used as the trigger for the gas discharge but with no activating compound on the two main electrodes. The patent literature describes in details the implementation of the so-called trigger wires (auxiliary electrodes) made of graphite, placed in between the two main electrodes, but no physical explanation has been given yet. We present experimental results, which show that stable cold field electron emission current in the high vacuum range originating from the nano-structured edge of the graphite layer is well correlated to the stable breakdown voltage of the GDT surge protector filled with a mixture of clean gases.

Positive solutions of advanced differential systems.

PubMed

Diblík, Josef; Kúdelčíková, Mária

2013-01-01

We study asymptotic behavior of solutions of general advanced differential systems y(t) = F(t, y(t)), where F : Ω → [Symbol: see text] (n) is a continuous quasi-bounded functional which satisfies a local Lipschitz condition with respect to the second argument and Ω is a subset in [Symbol: see text] × C(r)(n), C(r)(n) := C([0, r], [Symbol: see text] (n)), y t [Symbol: see text]C(r)(n), and y t (θ) = y(t + θ), θ [Symbol: see text] [0, r]. A monotone iterative method is proposed to prove the existence of a solution defined for t → ∞ with the graph coordinates lying between graph coordinates of two (lower and upper) auxiliary vector functions. This result is applied to scalar advanced linear differential equations. Criteria of existence of positive solutions are given and their asymptotic behavior is discussed.

Comparing the Caputo, Caputo-Fabrizio and Atangana-Baleanu derivative with fractional order: Fractional cubic isothermal auto-catalytic chemical system

NASA Astrophysics Data System (ADS)

Saad, K. M.

2018-03-01

In this work we extend the standard model for a cubic isothermal auto-catalytic chemical system (CIACS) to a new model of a fractional cubic isothermal auto-catalytic chemical system (FCIACS) based on Caputo (C), Caputo-Fabrizio (CF) and Atangana-Baleanu in the Liouville-Caputo sense (ABC) fractional time derivatives, respectively. We present approximate solutions for these extended models using the q -homotopy analysis transform method ( q -HATM). We solve the FCIACS with the C derivative and compare our results with those obtained using the CF and ABC derivatives. The ranges of convergence of the solutions are found and the optimal values of h , the auxiliary parameter, are derived. Finally, these solutions are compared with numerical solutions of the various models obtained using finite differences and excellent agreement is found.

Dynamic Weather Routes: A Weather Avoidance Concept for Trajectory-Based Operations

NASA Technical Reports Server (NTRS)

McNally, B. David; Love, John

2011-01-01

The integration of convective weather modeling with trajectory automation for conflict detection, trial planning, direct routing, and auto resolution has uncovered a concept that could help controllers, dispatchers, and pilots identify improved weather routes that result in significant savings in flying time and fuel burn. Trajectory automation continuously and automatically monitors aircraft in flight to find those that could potentially benefit from improved weather reroutes. Controllers, dispatchers, and pilots then evaluate reroute options to assess their suitability given current weather and traffic. In today's operations aircraft fly convective weather avoidance routes that were implemented often hours before aircraft approach the weather and automation does not exist to automatically monitor traffic to find improved weather routes that open up due to changing weather conditions. The automation concept runs in real-time and employs two keysteps. First, a direct routing algorithm automatically identifies flights with large dog legs in their routes and therefore potentially large savings in flying time. These are common - and usually necessary - during convective weather operations and analysis of Fort Worth Center traffic shows many aircraft with short cuts that indicate savings on the order of 10 flying minutes. The second and most critical step is to apply trajectory automation with weather modeling to determine what savings could be achieved by modifying the direct route such that it avoids weather and traffic and is acceptable to controllers and flight crews. Initial analysis of Fort Worth Center traffic suggests a savings of roughly 50% of the direct route savings could be achievable.The core concept is to apply trajectory automation with convective weather modeling in real time to identify a reroute that is free of weather and traffic conflicts and indicates enough time and fuel savings to be considered. The concept is interoperable with today's integrated FMS/datalink. Auxiliary(lat/long) waypoints define a minimum delay reroute between current position and a downstream capture fix beyond the weather. These auxiliary waypoints can be uplinked to equipped aircraft and auto-loaded into the FMS. Alternatively, for unequipped aircraft, auxiliary waypoints can be replaced by nearby named fixes, but this could reduce potential savings. The presentation includes an overview of the automation approach and focuses on several cases in terms of potential savings, reroute complexity, best auxiliary waypoint solution vs. named fix solution, and other metrics.

75 FR 34661 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-9-81 (MD-81), DC-9-82 (MD-82...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-18

... auxiliary fuel tanks, depending on the airplane configuration. This proposed AD results from fuel system... Fuel Tank System Design Review, Flammability Reduction and Maintenance and Inspection Requirements... substantiate that their fuel tank systems can prevent ignition sources in the fuel tanks. This requirement...

Evaluating non-relational storage technology for HEP metadata and meta-data catalog

NASA Astrophysics Data System (ADS)

Grigorieva, M. A.; Golosova, M. V.; Gubin, M. Y.; Klimentov, A. A.; Osipova, V. V.; Ryabinkin, E. A.

2016-10-01

Large-scale scientific experiments produce vast volumes of data. These data are stored, processed and analyzed in a distributed computing environment. The life cycle of experiment is managed by specialized software like Distributed Data Management and Workload Management Systems. In order to be interpreted and mined, experimental data must be accompanied by auxiliary metadata, which are recorded at each data processing step. Metadata describes scientific data and represent scientific objects or results of scientific experiments, allowing them to be shared by various applications, to be recorded in databases or published via Web. Processing and analysis of constantly growing volume of auxiliary metadata is a challenging task, not simpler than the management and processing of experimental data itself. Furthermore, metadata sources are often loosely coupled and potentially may lead to an end-user inconsistency in combined information queries. To aggregate and synthesize a range of primary metadata sources, and enhance them with flexible schema-less addition of aggregated data, we are developing the Data Knowledge Base architecture serving as the intelligence behind GUIs and APIs.

A high-resolution 7-Tesla fMRI dataset from complex natural stimulation with an audio movie

PubMed Central

Hanke, Michael; Baumgartner, Florian J.; Ibe, Pierre; Kaule, Falko R.; Pollmann, Stefan; Speck, Oliver; Zinke, Wolf; Stadler, Jörg

2014-01-01

Here we present a high-resolution functional magnetic resonance (fMRI) dataset – 20 participants recorded at high field strength (7 Tesla) during prolonged stimulation with an auditory feature film (“Forrest Gump”). In addition, a comprehensive set of auxiliary data (T1w, T2w, DTI, susceptibility-weighted image, angiography) as well as measurements to assess technical and physiological noise components have been acquired. An initial analysis confirms that these data can be used to study common and idiosyncratic brain response patterns to complex auditory stimulation. Among the potential uses of this dataset are the study of auditory attention and cognition, language and music perception, and social perception. The auxiliary measurements enable a large variety of additional analysis strategies that relate functional response patterns to structural properties of the brain. Alongside the acquired data, we provide source code and detailed information on all employed procedures – from stimulus creation to data analysis. In order to facilitate replicative and derived works, only free and open-source software was utilized. PMID:25977761

New Advanced Oxidation Technologies for Destruction of Pollutants in Water

DTIC Science & Technology

2001-09-01

biological desinfection of water from the secondary toxic substances after the plasmachemical treatment. The pulse UV treatment is applied for the...lowered pressure (10 - 30 torr), the burning of the auxiliary independent discharge above a surface of a solution did not influence on vital functions...sulfophthtalein reagent and for adsorption on the silica gel surface . But the radical fragments of surfactant molecules are complexing with the reagent and

Liquefaction of calcium-containing subbituminous coals and coals of lower rank

DOEpatents

Gorbaty, Martin L.; Taunton, John W.

1980-01-01

A process for the treatment of a calcium-containing subbituminous coal and coals of lower rank to form insoluble, thermally stable calcium salts which remain within the solids portions of the residue on liquefaction of the coal, thereby suppressing the formation scale, made up largely of calcium carbonate deposits, e.g., vaterite, which normally forms within the coal liquefaction reactor (i.e., coal liquefaction zone), e.g., on reactor surfaces, lines, auxiliary equipment and the like. A solution of a compound or salt characterized by the formula MX, where M is a Group IA metal of the Periodic Table of the Elements, and X is an anion which is capable of forming water-insoluble, thermally stable calcium compounds, is maintained in contact with a particulate coal feed sufficient to impregnate said salt or compound into the pores of the coal. On separation of the impregnated particulate coal from the solution, the coal can be liquefied in a coal liquefaction reactor (reaction zone) at coal liquefaction conditions without significant formation of vaterite or other forms of calcium carbonate on reactor surfaces, auxiliary equipment and the like; and the Group IA metal which remains within the liquefaction bottoms catalyzes the reaction when the liquefaction bottoms are subjected to a gasification reaction.

Semiclassical theory of the self-consistent vibration-rotation fields and its application to the bending-rotation interaction in the H{sub 2}O molecule

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skalozub, A.S.; Tsaune, A.Ya.

1994-12-01

A new approach for analyzing the highly excited vibration-rotation (VR) states of nonrigid molecules is suggested. It is based on the separation of the vibrational and rotational terms in the molecular VR Hamiltonian by introducing periodic auxiliary fields. These fields transfer different interactions within a molecule and are treated in terms of the mean-field approximation. As a result, the solution of the stationary Schroedinger equation with the VR Hamiltonian amounts to a quantization of the Berry phase in a problem of the molecular angular-momentum motion in a certain periodic VR field (rotational problem). The quantization procedure takes into account themore » motion of the collective vibrational variables in the appropriate VR potentials (vibrational problem). The quantization rules, the mean-field configurations of auxiliary interactions, and the solutions to the Schrodinger equations for the vibrational and rotational problems are self-consistently connected with one another. The potentialities of the theory are demonstrated by the bending-rotation interaction modeled by the Bunker-Landsberg potential function in the H{sub 2} molecule. The calculations are compared with both the results of the exact computations and those of other approximate methods. 32 refs., 4 tabs.« less

Precision improvement of frequency-modulated continuous-wave laser ranging system with two auxiliary interferometers

NASA Astrophysics Data System (ADS)

Shi, Guang; Wang, Wen; Zhang, Fumin

2018-03-01

The measurement precision of frequency-modulated continuous-wave (FMCW) laser distance measurement should be proportional to the scanning range of the tunable laser. However, the commercial external cavity diode laser (ECDL) is not an ideal tunable laser source in practical applications. Due to the unavoidable mode hopping and scanning nonlinearity of the ECDL, the measurement precision of FMCW laser distance measurements can be substantially affected. Therefore, an FMCW laser ranging system with two auxiliary interferometers is proposed in this paper. Moreover, to eliminate the effects of ECDL, the frequency-sampling method and mode hopping influence suppression method are employed. Compared with a fringe counting interferometer, this FMCW laser ranging system has a measuring error of ± 20 μm at the distance of 5.8 m.

46 CFR 58.01-35 - Main propulsion auxiliary machinery.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the system...

46 CFR 58.01-35 - Main propulsion auxiliary machinery.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the system...

46 CFR 58.01-35 - Main propulsion auxiliary machinery.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the system...

46 CFR 58.01-35 - Main propulsion auxiliary machinery.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the system...

46 CFR 58.01-35 - Main propulsion auxiliary machinery.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Main propulsion auxiliary machinery. 58.01-35 Section 58... AUXILIARY MACHINERY AND RELATED SYSTEMS General Requirements § 58.01-35 Main propulsion auxiliary machinery. Auxiliary machinery vital to the main propulsion system must be provided in duplicate unless the system...

30 CFR 75.331 - Auxiliary fans and tubing.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Auxiliary fans and tubing. 75.331 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.331 Auxiliary fans and tubing. (a) When auxiliary fans and tubing are used for face ventilation, each auxiliary fan shall be— (1...

Project Profile: Hydrogen Fuel Cell Mobile Lighting Tower (HFCML)

NASA Technical Reports Server (NTRS)

McLaughlin, Russell

2013-01-01

NASA is committed to finding innovative solutions that improve the operational performance of ground support equipment while providing environment and cost benefits, as well. Through the Hydrogen Fuel Cell Mobile Lighting Tower (HFCML) project, NASA gained operational exposure to a novel application of high efficiency technologies. Traditionally, outdoor lighting and auxiliary power at security gates, launch viewing sites, fallback areas, outage support, and special events is provided by diesel generators with metal halide lights. Diesel generators inherently contribute to C02, NOx, particulate emissions, and are very noisy. In 2010, engineers from NASA's Technology Evaluation for Environmental Risk Mitigation Principal Center (TEERM) introduced KSC operations to a novel technology for outdoor lighting needs. Developed by a team led by Sandia National Laboratory (SNL), the technology pairs a 5kW hydrogen fuel cell with robust high efficiency plasma lights in a towable trailer. Increased efficiency, in both the fuel cell power source and lighting load, yields longer run times between fueling operations while providing greater auxiliary power. Because of the unit's quiet operation and no exhaust fumes, it is capable of being used indoors and in emergency situations, and meets the needs of all other operational roles for metal halide/diesel generators. The only discharge is some water and warm air. Environmental benefits include elimination of diesel particulate emissions and estimated 73% greenhouse gas emissions savings when the hydrogen source is natural gas (per GREET model). As the technology matures the costs could become competitive for the fuel cell units which are approximately 5 times diesel units. Initial operational . concerns included the hydrogen storage tanks and valves, lightning safety/grounding, and required operating and refueling procedures. TEERM facilitated technical information exchange (design drawings, technical standards, and operations manuals) necessary for KSC hydrogen system experts to approve use of the HFCML unit, including initiating the environmental checklist (i.e. exterior lighting waiver due to sea turtles), and development of operations and maintenance instructions. TEERM worked with SNL to establish a bailment agreement for KSC to utilize a Beta unit as part of normal Center Operations for a period of twelve months.

Helping enhances productivity in campo flicker ( Colaptes campestris) cooperative groups

NASA Astrophysics Data System (ADS)

Dias, Raphael Igor; Webster, Michael S.; Macedo, Regina H.

2015-06-01

Reproductive adults in many bird species are assisted by non-breeding auxiliary helpers at the nest, yet the impact of auxiliaries on reproduction is variable and not always obvious. In this study, we tested Hamilton's rule and evaluated the effect of auxiliaries on productivity in the facultative cooperative breeder campo flicker ( Colaptes campestris campestris). Campo flickers have a variable mating system, with some groups having auxiliaries and others lacking them (i.e., unassisted pairs). Most auxiliaries are closely related to the breeding pair (primary auxiliaries), but some auxiliaries (secondary auxiliaries) are unrelated females that joined established groups. We found no effect of breeder quality (body condition) or territory quality (food availability) on group productivity, but the presence of auxiliaries increased the number of fledglings produced relative to unassisted pairs. Nonetheless, the indirect benefit of helping was small and did not outweigh the costs of delayed breeding and so seemed insufficient to explain the evolution of cooperative breeding in campo flickers. We concluded that some ecological constraints must limit dispersal or independent breeding, making staying in the group a "best-of-a-bad-job" situation for auxiliaries.

Helping enhances productivity in campo flicker (Colaptes campestris) cooperative groups.

PubMed

Dias, Raphael Igor; Webster, Michael S; Macedo, Regina H

2015-06-01

Reproductive adults in many bird species are assisted by non-breeding auxiliary helpers at the nest, yet the impact of auxiliaries on reproduction is variable and not always obvious. In this study, we tested Hamilton's rule and evaluated the effect of auxiliaries on productivity in the facultative cooperative breeder campo flicker (Colaptes campestris campestris). Campo flickers have a variable mating system, with some groups having auxiliaries and others lacking them (i.e., unassisted pairs). Most auxiliaries are closely related to the breeding pair (primary auxiliaries), but some auxiliaries (secondary auxiliaries) are unrelated females that joined established groups. We found no effect of breeder quality (body condition) or territory quality (food availability) on group productivity, but the presence of auxiliaries increased the number of fledglings produced relative to unassisted pairs. Nonetheless, the indirect benefit of helping was small and did not outweigh the costs of delayed breeding and so seemed insufficient to explain the evolution of cooperative breeding in campo flickers. We concluded that some ecological constraints must limit dispersal or independent breeding, making staying in the group a "best-of-a-bad-job" situation for auxiliaries.

46 CFR 58.25-10 - Main and auxiliary steering gear.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Main and auxiliary steering gear. 58.25-10 Section 58.25... AUXILIARY MACHINERY AND RELATED SYSTEMS Steering Gear § 58.25-10 Main and auxiliary steering gear. (a) Power-operated main and auxiliary steering gear must be separate systems that are independent throughout their...

U-folds as K3 fibrations

NASA Astrophysics Data System (ADS)

Braun, Andreas P.; Fucito, Francesco; Morales, Jose Francisco

2013-10-01

We study four-dimensional flux vacua describing intrinsic non- perturbative systems of 3 and 7 branes in type IIB string theory. The solutions are described as compactifications of a G(ravity) theory on a Calabi Yau threefold which consists of a fibration of an auxiliary K3 surface over an S 2 base. In the spirit of F-theory, the complex structure of the K3 surface varying over the base codifies the details of the fluxes, the dilaton and the warp factors in type IIB string theory. We discuss in detail some simple examples of geometric and non-geometric solutions where the precise flux/geometry dictionary can be explicitly worked out. In particular, we describe non-geometric T-fold solutions exhibiting non-trivial T-duality monodromies exchanging 3- and 7-branes.

Linear CCD attitude measurement system based on the identification of the auxiliary array CCD

NASA Astrophysics Data System (ADS)

Hu, Yinghui; Yuan, Feng; Li, Kai; Wang, Yan

2015-10-01

Object to the high precision flying target attitude measurement issues of a large space and large field of view, comparing existing measurement methods, the idea is proposed of using two array CCD to assist in identifying the three linear CCD with multi-cooperative target attitude measurement system, and to address the existing nonlinear system errors and calibration parameters and more problems with nine linear CCD spectroscopic test system of too complicated constraints among camera position caused by excessive. The mathematical model of binocular vision and three linear CCD test system are established, co-spot composition triangle utilize three red LED position light, three points' coordinates are given in advance by Cooperate Measuring Machine, the red LED in the composition of the three sides of a triangle adds three blue LED light points as an auxiliary, so that array CCD is easier to identify three red LED light points, and linear CCD camera is installed of a red filter to filter out the blue LED light points while reducing stray light. Using array CCD to measure the spot, identifying and calculating the spatial coordinates solutions of red LED light points, while utilizing linear CCD to measure three red LED spot for solving linear CCD test system, which can be drawn from 27 solution. Measured with array CCD coordinates auxiliary linear CCD has achieved spot identification, and has solved the difficult problems of multi-objective linear CCD identification. Unique combination of linear CCD imaging features, linear CCD special cylindrical lens system is developed using telecentric optical design, the energy center of the spot position in the depth range of convergence in the direction is perpendicular to the optical axis of the small changes ensuring highprecision image quality, and the entire test system improves spatial object attitude measurement speed and precision.

Military Energy Alternatives Conference

DTIC Science & Technology

2012-03-08

Power Generation and Alternative Energy Branch US Army RDECOM CERDEC CP&ID Power Division Aberdeen Proving Ground, MD...Co-generation Applications •Tactical Mobile Power •Vehicle-mounted Auxiliary Power and Environmental Control •Energy Security for Base...Mobile Power (PM MEP / PM CP) Vehicle Power (PM Tactical Vehicle / PM HTV) Portable Solar Photovoltaic (PV) Modules and Mobile Hybrid PV Power Sources

Agricultural Terrorism (Agroterror) and Escalation Theory

DTIC Science & Technology

2007-12-01

terrorists to overcome a series of major hurdles: gaining access to specialized chemical ingredients or virulent microbial strains; acquiring... milk cows, the third and final location is milk processing plants. For beef cattle, the third stage is...cattle on both farms and milk processing plants, the primary source of surveillance is the farm staff. Veterinarians serve as an auxiliary means of

The Open University in the Third World.

ERIC Educational Resources Information Center

Hawkridge, David G.

The British Open University is described in the first section of this paper as a multi-media system for teaching at a distance. Details are provided on the texts and other materials mailed to the students, the radio and television broadcasts provided by the British Broadcasting Company, and on the auxiliary sources of assistance offered to the…

78 FR 42411 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-16

... rear spar, and installation of a TFE sleeve if necessary. This new AD also adds airplanes to the... sources in the auxiliary (center) fuel tank, main fuel tanks, and surge tanks caused by a wiring short or... clamp location on the rear spar, and installation of a TFE sleeve if necessary. The NPRM also proposed...

Profiling of poorly stratified smoky atmospheres with scanning lidar

Treesearch

Vladimir Kovalev; Cyle Wold; Alexander Petkov; Wei Min Hao

2012-01-01

The multiangle data processing technique is considered based on using the signal measured in zenith (or close to zenith) as a core source for extracting the information about the vertical atmospheric aerosol loading. The multiangle signals are used as the auxiliary data to extract the vertical transmittance profile from the zenith signal. Simulated and experimental...

Input Consistency in the Acquisition of Questions in Bulgarian and English: A Hypothesis Testing Model

ERIC Educational Resources Information Center

Tornyova, Lidiya

2011-01-01

The goal of this dissertation is to address several major empirical and theoretical issues related to English-speaking children's difficulties with auxiliary use and inversion in questions. The empirical data on English question acquisition are inconsistent due to differences in methods and techniques used. A range of proposals about the source of…

Qualitative properties of large buckled states of spherical shells

NASA Technical Reports Server (NTRS)

Shih, K. G.; Antman, S. S.

1985-01-01

A system of 6th-order quasi-linear Ordinary Differential Equations is analyzed to show the global existence of axisymmetrically buckled states. A surprising nodal property is obtained which shows that everywhere along a branch of solutions that bifurcates from a simple eigenvalue of the linearized equation, the number of simultaneously vanishing points of both shear resultant and circumferential bending moment resultant remains invariant, provided that a certain auxiliary condition is satisfied.

Directory of Energy Information Administration model abstracts 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-01-01

This directory contains descriptions about each basic and auxiliary model, including the title, acronym, purpose, and type, followed by more detailed information on characteristics, uses, and requirements. For developing models, limited information is provided. Sources for additional information are identified. Included in this directory are 44 EIA models active as of February 1, 1988; 16 of which operate on personal computers. Models that run on personal computers are identified by ''PC'' as part of the acronyms. The main body of this directory is an alphabetical listing of all basic and auxiliary EIA models. Appendix A identifies major EIA modeling systemsmore » and the models within these systems, and Appendix B identifies EIA models by type (basic or auxiliary). Appendix C lists developing models and contact persons for those models. A basic model is one designated by the EIA Administrator as being sufficiently important to require sustained support and public scrutiny. An auxiliary model is one designated by the EIA Administrator as being used only occasionally in analyses, and therefore requires minimal levels of documentation. A developing model is one designated by the EIA Administrator as being under development and yet of sufficient interest to require a basic level of documentation at a future date. EIA also leases models developed by proprietary software vendors. Documentation for these ''proprietary'' models is the responsibility of the companies from which they are leased. EIA has recently leased models from Chase Econometrics, Inc., Data Resources, Inc. (DRI), the Oak Ridge National Laboratory (ORNL), and Wharton Econometric Forecasting Associates (WEFA). Leased models are not abstracted here.« less

Mars-GRAM Applications for Mars Science Laboratory Mission Site Selection Processes

NASA Technical Reports Server (NTRS)

Justh, Hilary; Justus, C. G.

2007-01-01

An overview is presented of the Mars-Global Reference Atmospheric Model (Mars-GRAM 2005) and its new features. One important new feature is the "auxiliary profile" option, whereby a simple input file is used to replace mean atmospheric values from Mars-GRAM's conventional (General Circulation Model) climatology. An auxiliary profile can be generated from any source of data or alternate model output. Results are presented using auxiliary profiles produced from mesoscale model output (Southwest Research Institute's Mars Regional Atmospheric Modeling System (MRAMS) model and Oregon State University's Mars mesoscale model (MMM5) model) for three candidate Mars Science Laboratory (MSL) landing sites (Terby Crater, Melas Chasma, and Gale Crater). A global Thermal Emission Spectrometer (TES) database has also been generated for purposes of making 'Mars-GRAM auxiliary profiles. This data base contains averages and standard deviations of temperature, density, and thermal wind components, averaged over 5-by-5 degree latitude bins and 15 degree L(sub S) bins, for each of three Mars years of TES nadir data. Comparisons show reasonably good consistency between Mars-GRAM with low dust optical depth and both TES observed and mesoscale model simulated density at the three study sites. Mean winds differ by a more significant degree. Comparisons of mesoscale and TES standard deviations' with conventional Mars-GRAM values, show that Mars-GRAM density perturbations are somewhat conservative (larger than observed variability), while mesoscale-modeled wind variations are larger than Mars-GRAM model estimates. Input parameters rpscale (for density perturbations) and rwscale (for wind perturbations) can be used to "recalibrate" Mars-GRAM perturbation magnitudes to better replicate observed or mesoscale model variability.

[Determination of organotin compounds in textile auxiliaries by gas chromatography-mass spectrometry].

PubMed

Li, Yanming; Hu, Yongjie; Liu, Jinhua; Guo, Yuliang; Wang, Guiqin

2011-04-01

A gas chromatography-mass spectrometry (GC-MS) method has been developed for the determination of dibutyltin (DBT), tributyltin (TBT) and triphenyltin (TPhT) in textile auxiliaries. The sample was first extracted with n-hexane in acetate buffer solution (pH 4.0) under ultrasonication (for hydrophobic sample) or oscillation extraction (for hydrophilic sample) and then derivatized with sodium tetraethylborate in tetrahydrofuran. The derivative was determined by GC-MS in selected ion monitoring (SIM) mode. The separation and quantification were achieved using a Rxi-5 ms silica capillary column (30 m x 0.25 mm x 0.25 microm). The linear ranges were 0.1-8.0 mg/L for both DBT and TBT, and 0.1-4.0 mg/L for TPhT. There were good linear relationships between the peak area and concentration in the linear ranges and the correlation coefficients (r2) were 0.9994-0.9998. The detection limits (LOD) were from 0.003 mg/L to 0.005 mg/L. The average recoveries of these organotin compounds at the three spiked levels of 4.0, 10.0 and 40.0 mg/kg were 92.6%-108.0% with the relative standard deviations (RSDs) of 2.5%-10.2%. The method is simple and accurate for simultaneous analysis of the DBT, TBT and TPhT in textile auxiliaries.

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2011 CFR

2011-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Side load on engine and auxiliary power...

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Side load on engine and auxiliary power...

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2013 CFR

2013-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Side load on engine and auxiliary power...

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2014 CFR

2014-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Side load on engine and auxiliary power...

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2012 CFR

2012-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Side load on engine and auxiliary power...

Training strategies and materials.

DOT National Transportation Integrated Search

2014-06-01

TxDOT project 0-6706 Design and Scope of Impact of Auxiliary Lanes has developed : guidelines for implementation of auxiliary lanes including general guidelines on the use of : auxiliary lanes and design guidelines for auxiliary lanes. To facil...

Large-scale 3D geoelectromagnetic modeling using parallel adaptive high-order finite element method

DOE PAGES

Grayver, Alexander V.; Kolev, Tzanio V.

2015-11-01

Here, we have investigated the use of the adaptive high-order finite-element method (FEM) for geoelectromagnetic modeling. Because high-order FEM is challenging from the numerical and computational points of view, most published finite-element studies in geoelectromagnetics use the lowest order formulation. Solution of the resulting large system of linear equations poses the main practical challenge. We have developed a fully parallel and distributed robust and scalable linear solver based on the optimal block-diagonal and auxiliary space preconditioners. The solver was found to be efficient for high finite element orders, unstructured and nonconforming locally refined meshes, a wide range of frequencies, largemore » conductivity contrasts, and number of degrees of freedom (DoFs). Furthermore, the presented linear solver is in essence algebraic; i.e., it acts on the matrix-vector level and thus requires no information about the discretization, boundary conditions, or physical source used, making it readily efficient for a wide range of electromagnetic modeling problems. To get accurate solutions at reduced computational cost, we have also implemented goal-oriented adaptive mesh refinement. The numerical tests indicated that if highly accurate modeling results were required, the high-order FEM in combination with the goal-oriented local mesh refinement required less computational time and DoFs than the lowest order adaptive FEM.« less

Large-scale 3D geoelectromagnetic modeling using parallel adaptive high-order finite element method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grayver, Alexander V.; Kolev, Tzanio V.

Here, we have investigated the use of the adaptive high-order finite-element method (FEM) for geoelectromagnetic modeling. Because high-order FEM is challenging from the numerical and computational points of view, most published finite-element studies in geoelectromagnetics use the lowest order formulation. Solution of the resulting large system of linear equations poses the main practical challenge. We have developed a fully parallel and distributed robust and scalable linear solver based on the optimal block-diagonal and auxiliary space preconditioners. The solver was found to be efficient for high finite element orders, unstructured and nonconforming locally refined meshes, a wide range of frequencies, largemore » conductivity contrasts, and number of degrees of freedom (DoFs). Furthermore, the presented linear solver is in essence algebraic; i.e., it acts on the matrix-vector level and thus requires no information about the discretization, boundary conditions, or physical source used, making it readily efficient for a wide range of electromagnetic modeling problems. To get accurate solutions at reduced computational cost, we have also implemented goal-oriented adaptive mesh refinement. The numerical tests indicated that if highly accurate modeling results were required, the high-order FEM in combination with the goal-oriented local mesh refinement required less computational time and DoFs than the lowest order adaptive FEM.« less

Quantifying road dust resuspension in urban environment by Multilinear Engine: A comparison with PMF2

NASA Astrophysics Data System (ADS)

Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

Atmospheric PM pollution from traffic comprises not only direct emissions but also non-exhaust emissions because resuspension of road dust that can produce high human exposure to heavy metals, metalloids, and mineral matter. A key task for establishing mitigation or preventive measures is estimating the contribution of road dust resuspension to the atmospheric PM mixture. Several source apportionment studies, applying receptor modeling at urban background sites, have shown the difficulty in identifying a road dust source separately from other mineral sources or vehicular exhausts. The Multilinear Engine (ME-2) is a computer program that can solve the Positive Matrix Factorization (PMF) problem. ME-2 uses a programming language permitting the solution to be guided toward some possible targets that can be derived from a priori knowledge of sources (chemical profile, ratios, etc.). This feature makes it especially suitable for source apportionment studies where partial knowledge of the sources is available. In the present study ME-2 was applied to data from an urban background site of Barcelona (Spain) to quantify the contribution of road dust resuspension to PM 10 and PM 2.5 concentrations. Given that recently the emission profile of local resuspended road dust was obtained (Amato, F., Pandolfi, M., Viana, M., Querol, X., Alastuey, A., Moreno, T., 2009. Spatial and chemical patterns of PM 10 in road dust deposited in urban environment. Atmospheric Environment 43 (9), 1650-1659), such a priori information was introduced in the model as auxiliary terms of the object function to be minimized by the implementation of the so-called "pulling equations". ME-2 permitted to enhance the basic PMF solution (obtained by PMF2) identifying, beside the seven sources of PMF2, the road dust source which accounted for 6.9 μg m -3 (17%) in PM 10, 2.2 μg m -3 (8%) of PM 2.5 and 0.3 μg m -3 (2%) of PM 1. This reveals that resuspension was responsible of the 37%, 15% and 3% of total traffic emissions respectively in PM 10, PM 2.5 and PM 1. Therefore the overall traffic contribution resulted in 18 μg m -3 (46%) in PM 10, 14 μg m -3 (51%) in PM 2.5 and 8 μg m -3 (48%) in PM 1. In PMF2 this mass explained by road dust resuspension was redistributed among the rest of sources, increasing mostly the mineral, secondary nitrate and aged sea salt contributions.

Tokamak power reactor ignition and time dependent fractional power operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vold, E.L.; Mau, T.K.; Conn, R.W.

1986-06-01

A flexible time-dependent and zero-dimensional plasma burn code with radial profiles was developed and employed to study the fractional power operation and the thermal burn control options for an INTOR-sized tokamak reactor. The code includes alpha thermalization and a time-dependent transport loss which can be represented by any one of several currently popular scaling laws for energy confinement time. Ignition parameters were found to vary widely in density-temperature (n-T) space for the range of scaling laws examined. Critical ignition issues were found to include the extent of confinement time degradation by alpha heating, the ratio of ion to electron transportmore » power loss, and effect of auxiliary heating on confinement. Feedback control of the auxiliary power and ion fuel sources are shown to provide thermal stability near the ignition curve.« less

Protecting single-photon entanglement with practical entanglement source

NASA Astrophysics Data System (ADS)

Zhou, Lan; Ou-Yang, Yang; Wang, Lei; Sheng, Yu-Bo

2017-06-01

Single-photon entanglement (SPE) is important for quantum communication and quantum information processing. However, SPE is sensitive to photon loss. In this paper, we discuss a linear optical amplification protocol for protecting SPE. Different from the previous protocols, we exploit the practical spontaneous parametric down-conversion (SPDC) source to realize the amplification, for the ideal entanglement source is unavailable in current quantum technology. Moreover, we prove that the amplification using the entanglement generated from SPDC source as auxiliary is better than the amplification assisted with single photons. The reason is that the vacuum state from SPDC source will not affect the amplification, so that it can be eliminated automatically. This protocol may be useful in future long-distance quantum communications.

Architecturing hierarchical function layers on self-assembled viral templates as 3D nano-array electrodes for integrated Li-ion microbatteries.

PubMed

Liu, Yihang; Zhang, Wei; Zhu, Yujie; Luo, Yanting; Xu, Yunhua; Brown, Adam; Culver, James N; Lundgren, Cynthia A; Xu, Kang; Wang, Yuan; Wang, Chunsheng

2013-01-09

This work enables an elegant bottom-up solution to engineer 3D microbattery arrays as integral power sources for microelectronics. Thus, multilayers of functional materials were hierarchically architectured over tobacco mosaic virus (TMV) templates that were genetically modified to self-assemble in a vertical manner on current-collectors, so that optimum power and energy densities accompanied with excellent cycle-life could be achieved on a minimum footprint. The resultant microbattery based on self-aligned LiFePO(4) nanoforests of shell-core-shell structure, with precise arrangement of various auxiliary material layers including a central nanometric metal core as direct electronic pathway to current collector, delivers excellent energy density and stable cycling stability only rivaled by the best Li-ion batteries of conventional configurations, while providing rate performance per foot-print and on-site manufacturability unavailable from the latter. This approach could open a new avenue for microelectromechanical systems (MEMS) applications, which would significantly benefit from the concept that electrochemically active components be directly engineered and fabricated as an integral part of the integrated circuit (IC).

Consideration of Thermoelectric Power Generation by Using Hot Spring Thermal Energy or Industrial Waste Heat

NASA Astrophysics Data System (ADS)

Sasaki, Keiichi; Horikawa, Daisuke; Goto, Koichi

2015-01-01

Today, we face some significant environmental and energy problems such as global warming, urban heat island, and the precarious balance of world oil supply and demand. However, we have not yet found a satisfactory solution to these problems. Waste heat recovery is considered to be one of the best solutions because it can improve energy efficiency by converting heat exhausted from plants and machinery to electric power. This technology would also prevent atmospheric temperature increases caused by waste heat, and decrease fossil fuel consumption by recovering heat energy, thus also reducing CO2 emissions. The system proposed in this research generates electric power by providing waste heat or unharnessed thermal energy to built-in thermoelectric modules that can convert heat into electric power. Waste heat can be recovered from many places, including machinery in industrial plants, piping in electric power plants, waste incineration plants, and so on. Some natural heat sources such as hot springs and solar heat can also be used for this thermoelectric generation system. The generated power is expected to be supplied to auxiliary machinery around the heat source, stored as an emergency power supply, and so on. The attributes of this system are (1) direct power generation using hot springs or waste heat; (2) 24-h stable power generation; (3) stand-alone power system with no noise and no vibration; and (4) easy maintenance attributed to its simple structure with no moving parts. In order to maximize energy use efficiency, the temperature difference between both sides of the thermoelectric (TE) modules built into the system need to be kept as large as possible. This means it is important to reduce thermal resistance between TE modules and heat source. Moreover, the system's efficiency greatly depends on the base temperature of the heat sources and the material of the system's TE modules. Therefore, in order to make this system practical and efficient, it is necessary to choose the heat source first and then design the most appropriate structure for the source by applying analytical methods. This report describes how to design a prototype of a thermoelectric power generator using the analytical approach and the results of performance evaluation tests carried out in the field.

Diurnal and seasonal trends and source apportionment of redox-active metals in Los Angeles using a novel online metal monitor and Positive Matrix Factorization (PMF)

NASA Astrophysics Data System (ADS)

Mousavi, Amirhosein; Sowlat, Mohammad H.; Sioutas, Constantinos

2018-02-01

In the present study, we identified the sources of four redox-active metals, including Iron (Fe), Chromium (Cr), Cupper (Cu), and Manganese (Mn) and quantified the contribution of these sources to PM2.5 concentrations in central Los Angeles, California, by employing time-resolved measurements (i.e., a time resolution of 2 h) with a recently developed online metal monitor and Positive Matrix Factorization (PMF). Size distribution of ambient PM (14 nm-10 μm) was measured using the Scanning Mobility Particle Sizer (SMPS) and Optical Particle Sizer (OPS). Auxiliary variables were also collected, including elemental (EC) and organic carbon (OC), gaseous pollutants (NO2 and O3), meteorological parameters (including relative humidity (RH) and temperature), and traffic data (for heavy- (HDVs) and light-duty vehicles (LDVs)). A 4-factor solution was found to be optimum for the chemically-speciated dataset, whereas a 5-factor solution appeared to be most plausible for the size distribution data. The factors included fresh traffic, soil/road dust, urban background aerosol, secondary aerosol, and nucleation (only resolved for the size distribution data). Fresh traffic was the major contributor to Fe and Cu concentrations, whereas Cr was mostly found in the urban background aerosol (reflecting a mixture of small local sources as well as aged traffic emissions), and Mn mostly came from both soil/road dust and was to a lesser degree found in urban background aerosol. Secondary aerosol did not contribute to the concentrations of any of these metals, but was associated with very high loading of OC, as expected. Even though the urban background aerosol and secondary aerosol appeared to be characterized by "aged" particles and have a rather homogeneous spatial distribution, the reactions and processes involved in their formation are entirely different. Our results provide insights into the sources of redox-active metals in central Los Angeles. They also underscore the benefits of novel measurement techniques for PM-bound metals, which could enhance our understanding of the sources of atmospheric aerosols by providing us with measurements with finer time resolutions that otherwise would not have been possible using traditional filter-based measurement techniques.

Type IIB flux vacua from G-theory II

NASA Astrophysics Data System (ADS)

Candelas, Philip; Constantin, Andrei; Damian, Cesar; Larfors, Magdalena; Morales, Jose Francisco

2015-02-01

We find analytic solutions of type IIB supergravity on geometries that locally take the form Mink × M 4 × ℂ with M 4 a generalised complex manifold. The solutions involve the metric, the dilaton, NSNS and RR flux potentials (oriented along the M 4) parametrised by functions varying only over ℂ. Under this assumption, the supersymmetry equations are solved using the formalism of pure spinors in terms of a finite number of holomorphic functions. Alternatively, the solutions can be viewed as vacua of maximally supersymmetric supergravity in six dimensions with a set of scalar fields varying holomorphically over ℂ. For a class of solutions characterised by up to five holomorphic functions, we outline how the local solutions can be completed to four-dimensional flux vacua of type IIB theory. A detailed study of this global completion for solutions with two holomorphic functions has been carried out in the companion paper [1]. The fluxes of the global solutions are, as in F-theory, entirely codified in the geometry of an auxiliary K3 fibration over ℂℙ1. The results provide a geometric construction of fluxes in F-theory.

DAU-TEAM Auxiliaries as CPR Instructors.

ERIC Educational Resources Information Center

McNeal, Donald R.; Reid, Stephen L.

1981-01-01

Dental auxiliaries are being used as instructors in cardiopulmonary resuscitation at the University of Kentucky College of Dentistry. Three advantages are found: improved dependability, improved perception of the auxiliaries by dental students and faculty, and improved self-esteem among auxiliaries. (MSE)

Rechargeable aqueous lithium-air batteries with an auxiliary electrode for the oxygen evolution

NASA Astrophysics Data System (ADS)

Sunahiro, S.; Matsui, M.; Takeda, Y.; Yamamoto, O.; Imanishi, N.

2014-09-01

A rechargeable aqueous lithium-air cell with a third auxiliary electrode for the oxygen evolution reaction was developed. The cell consists of a lithium metal anode, a lithium conducting solid electrolyte of Li1+x+yAlx(Ti,Ge)2-xSiyP3-yO12, a carbon black oxygen reduction air electrode, a RuO2 oxygen evolution electrode, and a saturated aqueous solution of LiOH with 10 M LiCl. The cell was successfully operated for several cycles at 0.64 mA cm-2 and 25 °C under air, where the capacity of air electrode was 2000 mAh gcathod-1. The cell performance was degraded gradually by cycling under open air. The degradation was reduced under CO2-free air and pure oxygen. The specific energy density was calculated to be 810 Wh kg-1 from the weight of water, lithium, oxygen, and carbon in the air electrode.

Entanglement and the fermion sign problem in auxiliary field quantum Monte Carlo simulations

NASA Astrophysics Data System (ADS)

Broecker, Peter; Trebst, Simon

2016-08-01

Quantum Monte Carlo simulations of fermions are hampered by the notorious sign problem whose most striking manifestation is an exponential growth of sampling errors with the number of particles. With the sign problem known to be an NP-hard problem and any generic solution thus highly elusive, the Monte Carlo sampling of interacting many-fermion systems is commonly thought to be restricted to a small class of model systems for which a sign-free basis has been identified. Here we demonstrate that entanglement measures, in particular the so-called Rényi entropies, can intrinsically exhibit a certain robustness against the sign problem in auxiliary-field quantum Monte Carlo approaches and possibly allow for the identification of global ground-state properties via their scaling behavior even in the presence of a strong sign problem. We corroborate these findings via numerical simulations of fermionic quantum phase transitions of spinless fermions on the honeycomb lattice at and below half filling.

Analysis of Nigerian dentists' opinion and consequences on expanded function dental auxiliaries.

PubMed

Umanah, A U; Azodo, C

2015-06-01

To examine Nigerian dentists' opinion on expanded function dental auxiliaries. This cross-sectional study of Nigerian dentists attending a dental conference was conducting in 2012 using self-administered questionnaire. The data were analyzed using Statistical Package for the Social Sciences version 16.0. P < 0.05 was considered statistically significant. The majority of the 82 dentists that participated in this study were male, aged 31-40 years, either specialist or specializing (residents), practiced for < 10 years, teaching hospital and urban practitioners. Of the participants, 22 (26.8%) reported favorable opinion towards expanded duty dental auxiliaries. The mean scores on consequences, of expanded function dental auxiliaries ranked redundancy of dentist as highest. Males and non-specialist significantly reported expanded function dental auxiliaries would lead to redundancy of dentists. Practitioners working in other hospitals other than teaching hospital significantly reported that appropriate legislation are necessary before expansion of duties of the dental auxiliaries can be done. The dentists with favorable opinion significantly reported that expanded duty dental auxiliaries would not cause redundancy of dentist and the task are not too difficult for dental auxiliaries with necessary training but will increase service delivery and efficiency, increase job satisfaction, lead to dental auxiliary specialization with legislation. Data from this study revealed overall unfavorable opinion of Nigerian dentists on the expanded duty dental auxiliaries. However, those with favorable opinion were significantly supportive of expanded function dental auxiliaries. This information would serve as a useful tool for Nigerian oral healthcare policy formulators.

Three dimensional PNS solutions of hypersonic internal flows with equilibrium chemistry

NASA Technical Reports Server (NTRS)

Liou, May-Fun

1989-01-01

An implicit procedure for solving parabolized Navier-Stokes equations under the assumption of a general equation of state for a gas in chemical equilibrium is given. A general and consistent approach for the evaluation of Jacobian matrices in the implicit operator avoids the use of unnecessary auxiliary quantities and approximations, and leads to a simple expression. Applications to two- and three-dimensional flow problems show efficiency in computer time and economy in storage.

Efficient Preconditioning for the p-Version Finite Element Method in Two Dimensions

DTIC Science & Technology

1989-10-01

paper, we study fast parallel preconditioners for systems of equations arising from the p-version finite element method. The p-version finite element...computations and the solution of a relatively small global auxiliary problem. We study two different methods. In the first (Section 3), the global...20], will be studied in the next section. Problem (3.12) is obviously much more easily solved than the original problem ,nd the procedure is highly

Exact solution for an optimal impermeable parachute problem

NASA Astrophysics Data System (ADS)

Lupu, Mircea; Scheiber, Ernest

2002-10-01

In the paper there are solved direct and inverse boundary problems and analytical solutions are obtained for optimization problems in the case of some nonlinear integral operators. It is modeled the plane potential flow of an inviscid, incompressible and nonlimited fluid jet, witch encounters a symmetrical, curvilinear obstacle--the deflector of maximal drag. There are derived integral singular equations, for direct and inverse problems and the movement in the auxiliary canonical half-plane is obtained. Next, the optimization problem is solved in an analytical manner. The design of the optimal airfoil is performed and finally, numerical computations concerning the drag coefficient and other geometrical and aerodynamical parameters are carried out. This model corresponds to the Helmholtz impermeable parachute problem.

An Algebraic Construction of the First Integrals of the Stationary KdV Hierarchy

NASA Astrophysics Data System (ADS)

Matsushima, Masatomo; Ohmiya, Mayumi

2009-09-01

The stationary KdV hierarchy is constructed using a kind of recursion operator called Λ-operator. The notion of the maximal solution of the n-th stationary KdV equation is introduced. Using this maximal solution, a specific differential polynomial with the auxiliary spectral parameter called the spectral M-function is constructed as the quadratic form of the fundamental system of the eigenvalue problem for the 2-nd order linear ordinary differential equation which is related to the linearizing operator of the hierarchy. By calculating a perfect square condition of the quadratic form by an elementary algebraic method, the complete set of first integrals of this hierarchy is constructed.

A Generalization of the Einstein-Maxwell Equations

NASA Astrophysics Data System (ADS)

Cotton, Fredrick

2016-03-01

The proposed modifications of the Einstein-Maxwell equations include: (1) the addition of a scalar term to the electromagnetic side of the equation rather than to the gravitational side, (2) the introduction of a 4-dimensional, nonlinear electromagnetic constitutive tensor and (3) the addition of curvature terms arising from the non-metric components of a general symmetric connection. The scalar term is defined by the condition that a spherically symmetric particle be force-free and mathematically well-behaved everywhere. The constitutive tensor introduces two auxiliary fields which describe the particle structure. The additional curvature terms couple both to particle solutions and to electromagnetic and gravitational wave solutions. http://sites.google.com/site/fwcotton/em-30.pdf

Post-stratified estimation of forest area and growing stock volume using lidar-based stratifications

Treesearch

Ronald E. McRoberts; Terje Gobakken; Erik Næsset

2012-01-01

National forest inventories report estimates of parameters related to forest area and growing stock volume for geographic areas ranging in size from municipalities to entire countries. Landsat imagery has been shown to be a source of auxiliary information that can be used with stratified estimation to increase the precision of estimates, although the increase is...

75 FR 52238 - Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 and ERJ...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-25

...) engine compressor stall after the Auxiliary Power Unit (APU) becomes the active bleed source for the left side. The most critical condition identified is: --Both engines close to idle (e.g.: descent phase); and --APU running; and --APU bleed button pushed in. In this condition, if the left hand (LH) engine...

Statistical rigor in LiDAR-assisted estimation of aboveground forest biomass

Treesearch

Timothy G. Gregoire; Erik Næsset; Ronald E. McRoberts; Göran Ståhl; Hans Andersen; Terje Gobakken; Liviu Ene; Ross Nelson

2016-01-01

For many decades remotely sensed data have been used as a source of auxiliary information when conducting regional or national surveys of forest resources. In the past decade, airborne scanning LiDAR (Light Detection and Ranging) has emerged as a promising tool for sample surveys aimed at improving estimation of aboveground forest biomass. This technology is now...

Power and Energy Strategy White Paper

DTIC Science & Technology

2010-04-01

and cooling. In recent years, several factors have emerged which further complicate the engineering and logistics challenges associated with power and...equation to maintain US military dominance in support of national security. II. INTRODUCTION Energy was a critical factor during many of the...non-combat platforms, especially for auxiliary power, and the compelling quest for compact, high capacity power sources for our overburdened Soldiers

20--500 watt AMTEC auxiliary electric power system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ivanenok, J.F. III; Sievers, R.K.

1996-12-31

Numerous design studies have been completed on Alkali Metal Thermal to Electric Converter (AMTEC) power systems for space applications demonstrating their substantial increase in performance. Recently design studies have been initiated to couple AMTEC power conversion with fossil fueled combustion systems. This paper describes the results of a Phase 1 SBIR effort to design an innovative, efficient, reliable, long life AMTEC Auxiliary Electric Power System (AEPS) for remote site applications (20--500 watts). The concept uses high voltage AMTEC cells, each containing 7 to 9 small electrolyte tubes, integrated with a combustor and recuperator. These multi-tube AMTEC cells are low cost,more » reliable, long life static converters. AMTEC technology is ideal for auxiliary electric power supplies that must operate reliably over a broad range of temperatures, fuel sources, power levels, and operational specifications. The simplicity, efficiency (20% systems) and modularity of this technology allow it to fill applications as varied as light-weight backpacks, remote site power supplies, and military base power. Phase 1 demonstrated the feasibility of a 20% system design, and showed that the development needs to focus on identifying long life AMTEC cell components, determining the AMTEC cell and system reliability, and demonstrating that a 20 watt AMTEC system is 3--5 times more efficient than existing systems for the same application.« less

Prevention of postpartum haemorrhage by community-based auxiliary midwives in hard-to-reach areas of Myanmar: a qualitative inquiry into acceptability and feasibility of task shifting.

PubMed

Than, Kyu Kyu; Mohamed, Yasmin; Oliver, Victoria; Myint, Theingi; La, Thazin; Beeson, James G; Luchters, Stanley

2017-05-17

In Myanmar, postpartum haemorrhage is the leading cause of maternal mortality and contributes to around 30% of all maternal deaths. The World Health Organization recommends training and supporting auxiliary midwives to administer oral misoprostol for prevention of postpartum haemorrhage in resource-limited settings. However, use of misoprostol by auxiliary midwives has not formally been approved in Myanmar. Our study aimed to explore community and provider perspectives on the roles of auxiliary midwives and community-level provision of oral misoprostol by auxiliary midwives. A qualitative inquiry was conducted in Ngape Township, Myanmar. A total of 15 focus group discussions with midwives, auxiliary midwives, community members and mothers with children under the age of three were conducted. Ten key informant interviews were performed with national, district and township level health planners and implementers of maternal and child health services. All audio recordings were transcribed verbatim in Myanmar language. Transcripts of focus group discussions were fully translated into English before coding, while key informants' data were coded in Myanmar language. Thematic analysis was done using ATLAS.ti software. Home births are common and auxiliary midwives were perceived as an essential care provider during childbirth in hard-to-reach areas. Main reasons provided were that auxiliary midwives are more accessible than midwives, live in the hard-to-reach areas, and are integrated in the community and well connected with midwives. Auxiliary midwives generally reported that their training involved instruction on active management of the third stage of labour, including use of misoprostol, but not all auxiliary midwives reported using misoprostol in practice. Supportive reasons for task-shifting administration of oral misoprostol to auxiliary midwives included discussions around the good relationship and trust between auxiliary midwives and midwives, whereby midwives felt confident distributing misoprostol to auxiliary midwives. However, the lack of clear government-level written permission to distribute the drug was perceived as a barrier to task shifting. This study highlights the acceptability of misoprostol use by auxiliary midwives to prevent postpartum haemorrhage, and findings suggest that it should be considered as a promising intervention for task shifting in Myanmar.

On flows of viscoelastic fluids under threshold-slip boundary conditions

NASA Astrophysics Data System (ADS)

Baranovskii, E. S.

2018-03-01

We investigate a boundary-value problem for the steady isothermal flow of an incompressible viscoelastic fluid of Oldroyd type in a 3D bounded domain with impermeable walls. We use the Fujita threshold-slip boundary condition. This condition states that the fluid can slip along a solid surface when the shear stresses reach a certain critical value; otherwise the slipping velocity is zero. Assuming that the flow domain is not rotationally symmetric, we prove an existence theorem for the corresponding slip problem in the framework of weak solutions. The proof uses methods for solving variational inequalities with pseudo-monotone operators and convex functionals, the method of introduction of auxiliary viscosity, as well as a passage-to-limit procedure based on energy estimates of approximate solutions, Korn’s inequality, and compactness arguments. Also, some properties and estimates of weak solutions are established.

45 CFR 707.10 - Auxiliary aids.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 45 Public Welfare 3 2013-10-01 2013-10-01 false Auxiliary aids. 707.10 Section 707.10 Public Welfare Regulations Relating to Public Welfare (Continued) COMMISSION ON CIVIL RIGHTS ENFORCEMENT OF... § 707.10 Auxiliary aids. (a) The Agency shall furnish appropriate auxiliary aids where necessary to...

45 CFR 707.10 - Auxiliary aids.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 45 Public Welfare 3 2012-10-01 2012-10-01 false Auxiliary aids. 707.10 Section 707.10 Public Welfare Regulations Relating to Public Welfare (Continued) COMMISSION ON CIVIL RIGHTS ENFORCEMENT OF... § 707.10 Auxiliary aids. (a) The Agency shall furnish appropriate auxiliary aids where necessary to...

45 CFR 707.10 - Auxiliary aids.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 45 Public Welfare 3 2011-10-01 2011-10-01 false Auxiliary aids. 707.10 Section 707.10 Public Welfare Regulations Relating to Public Welfare (Continued) COMMISSION ON CIVIL RIGHTS ENFORCEMENT OF... § 707.10 Auxiliary aids. (a) The Agency shall furnish appropriate auxiliary aids where necessary to...

45 CFR 707.10 - Auxiliary aids.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 45 Public Welfare 3 2014-10-01 2014-10-01 false Auxiliary aids. 707.10 Section 707.10 Public Welfare Regulations Relating to Public Welfare (Continued) COMMISSION ON CIVIL RIGHTS ENFORCEMENT OF... § 707.10 Auxiliary aids. (a) The Agency shall furnish appropriate auxiliary aids where necessary to...

47 CFR 73.1675 - Auxiliary antennas.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Auxiliary antennas. 73.1675 Section 73.1675... Rules Applicable to All Broadcast Stations § 73.1675 Auxiliary antennas. (a)(1) An auxiliary antenna is one that is permanently installed and available for use when the main antenna is out of service for...

47 CFR 73.1675 - Auxiliary antennas.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Auxiliary antennas. 73.1675 Section 73.1675... Rules Applicable to All Broadcast Stations § 73.1675 Auxiliary antennas. (a)(1) An auxiliary antenna is one that is permanently installed and available for use when the main antenna is out of service for...

47 CFR 73.1675 - Auxiliary antennas.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Auxiliary antennas. 73.1675 Section 73.1675... Rules Applicable to All Broadcast Stations § 73.1675 Auxiliary antennas. (a)(1) An auxiliary antenna is one that is permanently installed and available for use when the main antenna is out of service for...

47 CFR 73.1675 - Auxiliary antennas.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Auxiliary antennas. 73.1675 Section 73.1675... Rules Applicable to All Broadcast Stations § 73.1675 Auxiliary antennas. (a)(1) An auxiliary antenna is one that is permanently installed and available for use when the main antenna is out of service for...

47 CFR 73.1675 - Auxiliary antennas.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Auxiliary antennas. 73.1675 Section 73.1675... Rules Applicable to All Broadcast Stations § 73.1675 Auxiliary antennas. (a)(1) An auxiliary antenna is one that is permanently installed and available for use when the main antenna is out of service for...

30 CFR 57.8529 - Auxiliary fan systems

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Auxiliary fan systems 57.8529 Section 57.8529 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Underground Only § 57.8529 Auxiliary fan systems When auxiliary fan systems are used, such systems shall...

14 CFR 29.757 - Hull and auxiliary float strength.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and auxiliary float strength. 29.757... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and Hulls § 29.757 Hull and auxiliary float strength. The hull, and auxiliary floats if used, must withstand the...

7 CFR 15b.37 - Auxiliary aids.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 1 2012-01-01 2012-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary to...

7 CFR 15b.37 - Auxiliary aids.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 1 2014-01-01 2014-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary to...

7 CFR 15b.37 - Auxiliary aids.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 1 2011-01-01 2011-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary to...

7 CFR 15b.37 - Auxiliary aids.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 1 2013-01-01 2013-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary to...

14 CFR 29.757 - Hull and auxiliary float strength.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Hull and auxiliary float strength. 29.757 Section 29.757 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... § 29.757 Hull and auxiliary float strength. The hull, and auxiliary floats if used, must withstand the...

30 CFR 75.331 - Auxiliary fans and tubing.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (a) When auxiliary fans and tubing are used for face ventilation, each auxiliary fan shall be— (1... auxiliary fan is stopped— (1) Line brattice or other face ventilation control devices shall be used to maintain ventilation to affected faces; and (2) Electrical equipment in the affected working places shall...

30 CFR 75.331 - Auxiliary fans and tubing.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (a) When auxiliary fans and tubing are used for face ventilation, each auxiliary fan shall be— (1... auxiliary fan is stopped— (1) Line brattice or other face ventilation control devices shall be used to maintain ventilation to affected faces; and (2) Electrical equipment in the affected working places shall...

30 CFR 75.331 - Auxiliary fans and tubing.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (a) When auxiliary fans and tubing are used for face ventilation, each auxiliary fan shall be— (1... auxiliary fan is stopped— (1) Line brattice or other face ventilation control devices shall be used to maintain ventilation to affected faces; and (2) Electrical equipment in the affected working places shall...

7 CFR 15b.37 - Auxiliary aids.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 1 2010-01-01 2010-01-01 false Auxiliary aids. 15b.37 Section 15b.37 Agriculture... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Other Aid, Benefits, or Services § 15b.37 Auxiliary aids... appropriate auxiliary aids to persons with impaired sensory, manual, or speaking skills, where necessary to...

Determination of the Fracture Parameters in a Stiffened Composite Panel

NASA Technical Reports Server (NTRS)

Lin, Chung-Yi

2000-01-01

A modified J-integral, namely the equivalent domain integral, is derived for a three-dimensional anisotropic cracked solid to evaluate the stress intensity factor along the crack front using the finite element method. Based on the equivalent domain integral method with auxiliary fields, an interaction integral is also derived to extract the second fracture parameter, the T-stress, from the finite element results. The auxiliary fields are the two-dimensional plane strain solutions of monoclinic materials with the plane of symmetry at x(sub 3) = 0 under point loads applied at the crack tip. These solutions are expressed in a compact form based on the Stroh formalism. Both integrals can be implemented into a single numerical procedure to determine the distributions of stress intensity factor and T-stress components, T11, T13, and thus T33, along a three-dimensional crack front. The effects of plate thickness and crack length on the variation of the stress intensity factor and T-stresses through the thickness are investigated in detail for through-thickness center-cracked plates (isotropic and orthotropic) and orthotropic stiffened panels under pure mode-I loading conditions. For all the cases studied, T11 remains negative. For plates with the same dimensions, a larger size of crack yields larger magnitude of the normalized stress intensity factor and normalized T-stresses. The results in orthotropic stiffened panels exhibit an opposite trend in general. As expected, for the thicker panels, the fracture parameters evaluated through the thickness, except the region near the free surfaces, approach two-dimensional plane strain solutions. In summary, the numerical methods presented in this research demonstrate their high computational effectiveness and good numerical accuracy in extracting these fracture parameters from the finite element results in three-dimensional cracked solids.

Auxiliary reactor for a hydrocarbon reforming system

DOEpatents

Clawson, Lawrence G.; Dorson, Matthew H.; Mitchell, William L.; Nowicki, Brian J.; Bentley, Jeffrey M.; Davis, Robert; Rumsey, Jennifer W.

2006-01-17

An auxiliary reactor for use with a reformer reactor having at least one reaction zone, and including a burner for burning fuel and creating a heated auxiliary reactor gas stream, and heat exchanger for transferring heat from auxiliary reactor gas stream and heat transfer medium, preferably two-phase water, to reformer reaction zone. Auxiliary reactor may include first cylindrical wall defining a chamber for burning fuel and creating a heated auxiliary reactor gas stream, the chamber having an inlet end, an outlet end, a second cylindrical wall surrounding first wall and a second annular chamber there between. The reactor being configured so heated auxiliary reactor gas flows out the outlet end and into and through second annular chamber and conduit which is disposed in second annular chamber, the conduit adapted to carry heat transfer medium and being connectable to reformer reaction zone for additional heat exchange.

30 CFR 57.8534 - Shutdown or failure of auxiliary fans.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Shutdown or failure of auxiliary fans. 57.8534... Ventilation Underground Only § 57.8534 Shutdown or failure of auxiliary fans. (a) Auxiliary fans installed and... fan maintenance or fan adjustments where air quality is maintained in compliance with the applicable...

76 FR 28795 - Privacy Act of 1974; Department of Homeland Security United States Coast Guard-024 Auxiliary...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-18

... 1974; Department of Homeland Security United States Coast Guard-024 Auxiliary Database System of... Security/United States Coast Guard-024 Auxiliary Database (AUXDATA) System of Records.'' This system of... titled, ``DHS/USCG-024 Auxiliary Database (AUXDATA) System of Records.'' The AUXDATA system is the USCG's...

The Bacillus subtilis Conjugative Plasmid pLS20 Encodes Two Ribbon-Helix-Helix Type Auxiliary Relaxosome Proteins That Are Essential for Conjugation.

PubMed

Miguel-Arribas, Andrés; Hao, Jian-An; Luque-Ortega, Juan R; Ramachandran, Gayetri; Val-Calvo, Jorge; Gago-Córdoba, César; González-Álvarez, Daniel; Abia, David; Alfonso, Carlos; Wu, Ling J; Meijer, Wilfried J J

2017-01-01

Bacterial conjugation is the process by which a conjugative element (CE) is transferred horizontally from a donor to a recipient cell via a connecting pore. One of the first steps in the conjugation process is the formation of a nucleoprotein complex at the origin of transfer ( oriT ), where one of the components of the nucleoprotein complex, the relaxase, introduces a site- and strand specific nick to initiate the transfer of a single DNA strand into the recipient cell. In most cases, the nucleoprotein complex involves, besides the relaxase, one or more additional proteins, named auxiliary proteins, which are encoded by the CE and/or the host. The conjugative plasmid pLS20 replicates in the Gram-positive Firmicute bacterium Bacillus subtilis . We have recently identified the relaxase gene and the oriT of pLS20, which are separated by a region of almost 1 kb. Here we show that this region contains two auxiliary genes that we name aux1 LS20 and aux2 LS20 , and which we show are essential for conjugation. Both Aux1 LS20 and Aux2 LS20 are predicted to contain a Ribbon-Helix-Helix DNA binding motif near their N-terminus. Analyses of the purified proteins show that Aux1 LS20 and Aux2 LS20 form tetramers and hexamers in solution, respectively, and that they both bind preferentially to oriT LS20 , although with different characteristics and specificities. In silico analyses revealed that genes encoding homologs of Aux1 LS20 and/or Aux2 LS20 are located upstream of almost 400 relaxase genes of the Rel LS20 family (MOB L ) of relaxases. Thus, Aux1 LS20 and Aux2 LS20 of pLS20 constitute the founding member of the first two families of auxiliary proteins described for CEs of Gram-positive origin.

Improved Horvitz-Thompson Estimation of Model Parameters from Two-phase Stratified Samples: Applications in Epidemiology

PubMed Central

Breslow, Norman E.; Lumley, Thomas; Ballantyne, Christie M; Chambless, Lloyd E.; Kulich, Michal

2009-01-01

The case-cohort study involves two-phase sampling: simple random sampling from an infinite super-population at phase one and stratified random sampling from a finite cohort at phase two. Standard analyses of case-cohort data involve solution of inverse probability weighted (IPW) estimating equations, with weights determined by the known phase two sampling fractions. The variance of parameter estimates in (semi)parametric models, including the Cox model, is the sum of two terms: (i) the model based variance of the usual estimates that would be calculated if full data were available for the entire cohort; and (ii) the design based variance from IPW estimation of the unknown cohort total of the efficient influence function (IF) contributions. This second variance component may be reduced by adjusting the sampling weights, either by calibration to known cohort totals of auxiliary variables correlated with the IF contributions or by their estimation using these same auxiliary variables. Both adjustment methods are implemented in the R survey package. We derive the limit laws of coefficients estimated using adjusted weights. The asymptotic results suggest practical methods for construction of auxiliary variables that are evaluated by simulation of case-cohort samples from the National Wilms Tumor Study and by log-linear modeling of case-cohort data from the Atherosclerosis Risk in Communities Study. Although not semiparametric efficient, estimators based on adjusted weights may come close to achieving full efficiency within the class of augmented IPW estimators. PMID:20174455

The health beliefs of hospital staff and the reporting of needlestick injury.

PubMed

Tabak, Nili; Shiaabana, Amal Musaa; Shasha, Shaul

2006-10-01

The aim of this study is to examine the connection between the health beliefs of hospital staff (doctors, nurses and auxiliary staff) and their failure to report needlestick injuries. Needlestick injury to hospital staff is quite frequent and can result in infections and disease, but staff frequently do not report the injury despite their awareness of the risk of blood-borne pathogens. Five questionnaires were constructed based on three existing research tools and were tested for validity and reliability. Two hundred and forty questionnaires were distributed to eight randomly chosen departments of a single Israeli hospital. Seventy-six percent of the questionnaires were anonymously completed and returned. Nurses had the highest rate of needlestick injury, followed by auxiliary staff and doctors. Auxiliary staff showed the highest rate of compliance with the duty to report such injuries, while doctors showed the lowest. Perceived severity of contractable disease, the perceived efficacy of reporting injuries and overall motivation to maintain health were the best predictors of reporting compliance. Non-compliers emphasized the negative aspects of reporting the injuries, primarily that it took up too much time. The solution to non-compliance with the duty to report must be a targeted investment in training and education. Relevance to clinical practice. Finding the reasons for compliance and non-compliance with the duty to report needlestick injuries will help in designing educational programmes for hospital staff and in determining a strategy for improving health behaviour.

Black box multigrid

NASA Technical Reports Server (NTRS)

Dendy, J. E., Jr.

1981-01-01

The black box multigrid (BOXMG) code, which only needs specification of the matrix problem for application in the multigrid method was investigated. It is contended that a major problem with the multigrid method is that each new grid configuration requires a major programming effort to develop a code that specifically handles that grid configuration. The SOR and ICCG methods only specify the matrix problem, no matter what the grid configuration. It is concluded that the BOXMG does everything else necessary to set up the auxiliary coarser problems to achieve a multigrid solution.

More on the scalar-tensor BF theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, Harvendra

2009-09-15

This work is based on an earlier proposal [H. Singh, Phys. Lett. B 673, 68 (2009)] that the membrane BF theory consists of matter fields along with Chern-Simons fields as well as the auxiliary pairs of scalar and tensor fields. In particular, we discuss the supersymmetry aspects of such a membrane theory. It is concluded that the theory possesses maximal supersymmetry, and it is related to the L-BLG theory via a field map. We obtain fuzzy-sphere solution, and corresponding tensor field configuration is given.

Solar-energy-system-performance evaluation: Perl-Mack Enterprises, Inc. , single-family residence, Denver, Colorado, April 1978-March 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, R.V.

1979-01-01

The Perl-Mack Enterprises, Inc. site is a single-family dwelling whose solar heating system is designed to provide approximately 68% of the annual space heating and hot water requirements. The system consists of an array of flat plate collectors using a water-propylene glycol solution, a concrete water storage tank, and an auxiliary gas burner. The system is described, and its performance is analyzed using a system energy balance technique. (LEW)

Classical dynamics on curved Snyder space

NASA Astrophysics Data System (ADS)

Ivetić, B.; Meljanac, S.; Mignemi, S.

2014-05-01

We study the classical dynamics of a particle in nonrelativistic Snyder-de Sitter space. We show that for spherically symmetric systems, parameterizing the solutions in terms of an auxiliary time variable, which is a function only of the physical time and of the energy and angular momentum of the particles, one can reduce the problem to the equivalent one in classical mechanics. We also discuss a relativistic extension of these results, and a generalization to the case in which the algebra is realized in flat space.

Connecting the Dots: Linking Creativity, Synthesis Skills, and the Students' Anxiety about the Future

ERIC Educational Resources Information Center

Susnea, Ioan; Pecheanu, Emilia; Dumitriu, Luminita; Cocu, Adina

2017-01-01

In the past few years we have participated in several EU funded projects, aimed to create the educational content and auxiliary ICT tools to support the development of some essential soft skills of the students: the creativity, and the ability to write syntheses of the ideas extracted from various sources. In this context, we produced an easy to…

Deep Wideband Single Pointings and Mosaics in Radio Interferometry: How Accurately Do We Reconstruct Intensities and Spectral Indices of Faint Sources?

NASA Astrophysics Data System (ADS)

Rau, U.; Bhatnagar, S.; Owen, F. N.

2016-11-01

Many deep wideband wide-field radio interferometric surveys are being designed to accurately measure intensities, spectral indices, and polarization properties of faint source populations. In this paper, we compare various wideband imaging methods to evaluate the accuracy to which intensities and spectral indices of sources close to the confusion limit can be reconstructed. We simulated a wideband single-pointing (C-array, L-Band (1-2 GHz)) and 46-pointing mosaic (D-array, C-Band (4-8 GHz)) JVLA observation using a realistic brightness distribution ranging from 1 μJy to 100 mJy and time-, frequency-, polarization-, and direction-dependent instrumental effects. The main results from these comparisons are (a) errors in the reconstructed intensities and spectral indices are larger for weaker sources even in the absence of simulated noise, (b) errors are systematically lower for joint reconstruction methods (such as Multi-Term Multi-Frequency-Synthesis (MT-MFS)) along with A-Projection for accurate primary beam correction, and (c) use of MT-MFS for image reconstruction eliminates Clean-bias (which is present otherwise). Auxiliary tests include solutions for deficiencies of data partitioning methods (e.g., the use of masks to remove clean bias and hybrid methods to remove sidelobes from sources left un-deconvolved), the effect of sources not at pixel centers, and the consequences of various other numerical approximations within software implementations. This paper also demonstrates the level of detail at which such simulations must be done in order to reflect reality, enable one to systematically identify specific reasons for every trend that is observed, and to estimate scientifically defensible imaging performance metrics and the associated computational complexity of the algorithms/analysis procedures. The National Radio Astronomy Observatory is a facility of the National Science Foundation operated under cooperative agreement by Associated Universities, Inc.

Crystallization-induced dynamic resolution of Fox chiral auxiliary and application to the diastereoselective electrophilic fluorination of amide enolates.

PubMed

Lubin, Hodney; Dupuis, Christophe; Pytkowicz, Julien; Brigaud, Thierry

2013-04-05

A highly efficient crystallization-induced dynamic resolution (CIDR) of trans-Fox (fluorinated oxazolidine) chiral auxiliary is reported. This chiral auxiliary was used for highly diastereoselective (>98% de) electrophilic fluorination of amide enolates. After removal of the chiral auxiliary, highly valuable enantiopure α-fluorocarboxylic acids and β-fluoroalcohols are obtained.

49 CFR 39.63 - What modifications and auxiliary aids and services are required at terminals and other landside...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 1 2013-10-01 2013-10-01 false What modifications and auxiliary aids and services... modifications and auxiliary aids and services are required at terminals and other landside facilities for... of auxiliary aids and services. To the extent that this information is not available to these...

49 CFR 39.63 - What modifications and auxiliary aids and services are required at terminals and other landside...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 1 2014-10-01 2014-10-01 false What modifications and auxiliary aids and services... modifications and auxiliary aids and services are required at terminals and other landside facilities for... of auxiliary aids and services. To the extent that this information is not available to these...

49 CFR 39.63 - What modifications and auxiliary aids and services are required at terminals and other landside...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 1 2012-10-01 2012-10-01 false What modifications and auxiliary aids and services... modifications and auxiliary aids and services are required at terminals and other landside facilities for... of auxiliary aids and services. To the extent that this information is not available to these...

A Note on the Use of Missing Auxiliary Variables in Full Information Maximum Likelihood-Based Structural Equation Models

ERIC Educational Resources Information Center

Enders, Craig K.

2008-01-01

Recent missing data studies have argued in favor of an "inclusive analytic strategy" that incorporates auxiliary variables into the estimation routine, and Graham (2003) outlined methods for incorporating auxiliary variables into structural equation analyses. In practice, the auxiliary variables often have missing values, so it is reasonable to…

BE, DO, and Modal Auxiliaries of 3-Year-Old African American English Speakers

ERIC Educational Resources Information Center

Newkirk-Turner, Brandi L.; Oetting, Janna B.; Stockman, Ida J.

2014-01-01

Purpose: This study examined African American English--speaking children's use of BE, DO, and modal auxiliaries. Method: The data were based on language samples obtained from 48 three-year-olds. Analyses examined rates of marking by auxiliary type, auxiliary surface form, succeeding element, and syntactic construction and by a number of child…

Preliminary study of a hydrogen peroxide rocket for use in moving source jet noise tests

NASA Technical Reports Server (NTRS)

Plencner, R. M.

1977-01-01

A preliminary investigation was made of using a hydrogen peroxide rocket to obtain pure moving source jet noise data. The thermodynamic cycle of the rocket was analyzed. It was found that the thermodynamic exhaust properties of the rocket could be made to match those of typical advanced commercial supersonic transport engines. The rocket thruster was then considered in combination with a streamlined ground car for moving source jet noise experiments. When a nonthrottlable hydrogen peroxide rocket was used to accelerate the vehicle, propellant masses and/or acceleration distances became too large. However, when a throttlable rocket or an auxiliary system was used to accelerate the vehicle, reasonable propellant masses could be obtained.

Soliton-cnoidal interactional wave solutions for the reduced Maxwell-Bloch equations

NASA Astrophysics Data System (ADS)

Huang, Li-Li; Qiao, Zhi-Jun; Chen, Yong

2018-02-01

Based on nonlocal symmetry method, localized excitations and interactional solutions are investigated for the reduced Maxwell-Bloch equations. The nonlocal symmetries of the reduced Maxwell-Bloch equations are obtained by the truncated Painleve expansion approach and the Mobious invariant property. The nonlocal symmetries are localized to a prolonged system by introducing suitable auxiliary dependent variables. The extended system can be closed and a novel Lie point symmetry system is constructed. By solving the initial value problems, a new type of finite symmetry transformations is obtained to derive periodic waves, Ma breathers and breathers travelling on the background of periodic line waves. Then rich exact interactional solutions are derived between solitary waves and other waves including cnoidal waves, rational waves, Painleve waves, and periodic waves through similarity reductions. In particular, several new types of localized excitations including rogue waves are found, which stem from the arbitrary function generated in the process of similarity reduction. By computer numerical simulation, the dynamics of these localized excitations and interactional solutions are discussed, which exhibit meaningful structures.

Newton's method applied to finite-difference approximations for the steady-state compressible Navier-Stokes equations

NASA Technical Reports Server (NTRS)

Bailey, Harry E.; Beam, Richard M.

1991-01-01

Finite-difference approximations for steady-state compressible Navier-Stokes equations, whose two spatial dimensions are written in generalized curvilinear coordinates and strong conservation-law form, are presently solved by means of Newton's method in order to obtain a lifting-airfoil flow field under subsonic and transonnic conditions. In addition to ascertaining the computational requirements of an initial guess ensuring convergence and the degree of computational efficiency obtainable via the approximate Newton method's freezing of the Jacobian matrices, attention is given to the need for auxiliary methods assessing the temporal stability of steady-state solutions. It is demonstrated that nonunique solutions of the finite-difference equations are obtainable by Newton's method in conjunction with a continuation method.

Reformulating the Schrödinger equation as a Shabat-Zakharov system

NASA Astrophysics Data System (ADS)

Boonserm, Petarpa; Visser, Matt

2010-02-01

We reformulate the second-order Schrödinger equation as a set of two coupled first-order differential equations, a so-called "Shabat-Zakharov system" (sometimes called a "Zakharov-Shabat" system). There is considerable flexibility in this approach, and we emphasize the utility of introducing an "auxiliary condition" or "gauge condition" that is used to cut down the degrees of freedom. Using this formalism, we derive the explicit (but formal) general solution to the Schrödinger equation. The general solution depends on three arbitrarily chosen functions, and a path-ordered exponential matrix. If one considers path ordering to be an "elementary" process, then this represents complete quadrature, albeit formal, of the second-order linear ordinary differential equation.

General Theory of Aerodynamic Instability and the Mechanism of Flutter

NASA Technical Reports Server (NTRS)

Theodorsen, Theodore

1979-01-01

The aerodynamic forces on an oscillating airfoil or airfoil-aileron combination of three independent degrees of freedom were determined. The problem resolves itself into the solution of certain definite integrals, which were identified as Bessel functions of the first and second kind, and of zero and first order. The theory, based on potential flow and the Kutta condition, is fundamentally equivalent to the conventional wing section theory relating to the steady case. The air forces being known, the mechanism of aerodynamic instability was analyzed. An exact solution, involving potential flow and the adoption of the Kutta condition, was derived. The solution is of a simple form and is expressed by means of an auxiliary parameter k. The flutter velocity, treated as the unknown quantity, was determined as a function of a certain ratio of the frequencies in the separate degrees of freedom for any magnitudes and combinations of the airfoil-aileron parameters.

49 CFR 39.51 - What is the general requirement for PVOs' provision of auxiliary aids and services to passengers?

Code of Federal Regulations, 2013 CFR

2013-10-01

...' provision of auxiliary aids and services to passengers? 39.51 Section 39.51 Transportation Office of the... for Passengers § 39.51 What is the general requirement for PVOs' provision of auxiliary aids and... auxiliary aids and services where necessary to afford an individual with a disability an equal opportunity...

49 CFR 39.51 - What is the general requirement for PVOs' provision of auxiliary aids and services to passengers?

Code of Federal Regulations, 2014 CFR

2014-10-01

...' provision of auxiliary aids and services to passengers? 39.51 Section 39.51 Transportation Office of the... for Passengers § 39.51 What is the general requirement for PVOs' provision of auxiliary aids and... auxiliary aids and services where necessary to afford an individual with a disability an equal opportunity...

49 CFR 39.51 - What is the general requirement for PVOs' provision of auxiliary aids and services to passengers?

Code of Federal Regulations, 2011 CFR

2011-10-01

...' provision of auxiliary aids and services to passengers? 39.51 Section 39.51 Transportation Office of the... for Passengers § 39.51 What is the general requirement for PVOs' provision of auxiliary aids and... auxiliary aids and services where necessary to afford an individual with a disability an equal opportunity...

49 CFR 39.51 - What is the general requirement for PVOs' provision of auxiliary aids and services to passengers?

Code of Federal Regulations, 2012 CFR

2012-10-01

...' provision of auxiliary aids and services to passengers? 39.51 Section 39.51 Transportation Office of the... for Passengers § 39.51 What is the general requirement for PVOs' provision of auxiliary aids and... auxiliary aids and services where necessary to afford an individual with a disability an equal opportunity...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dubrovsky, V. G.; Topovsky, A. V.

New exact solutions, nonstationary and stationary, of Veselov-Novikov (VN) equation in the forms of simple nonlinear and linear superpositions of arbitrary number N of exact special solutions u{sup (n)}, n= 1, Horizontal-Ellipsis , N are constructed via Zakharov and Manakov {partial_derivative}-dressing method. Simple nonlinear superpositions are represented up to a constant by the sums of solutions u{sup (n)} and calculated by {partial_derivative}-dressing on nonzero energy level of the first auxiliary linear problem, i.e., 2D stationary Schroedinger equation. It is remarkable that in the zero energy limit simple nonlinear superpositions convert to linear ones in the form of the sums ofmore » special solutions u{sup (n)}. It is shown that the sums u=u{sup (k{sub 1})}+...+u{sup (k{sub m})}, 1 Less-Than-Or-Slanted-Equal-To k{sub 1} < k{sub 2} < Horizontal-Ellipsis < k{sub m} Less-Than-Or-Slanted-Equal-To N of arbitrary subsets of these solutions are also exact solutions of VN equation. The presented exact solutions include as superpositions of special line solitons and also superpositions of plane wave type singular periodic solutions. By construction these exact solutions represent also new exact transparent potentials of 2D stationary Schroedinger equation and can serve as model potentials for electrons in planar structures of modern electronics.« less

Assessment of the further improved (G'/G)-expansion method and the extended tanh-method in probing exact solutions of nonlinear PDEs.

PubMed

Akbar, M Ali; Ali, Norhashidah Hj Mohd; Mohyud-Din, Syed Tauseef

2013-01-01

The (G'/G)-expansion method is one of the most direct and effective method for obtaining exact solutions of nonlinear partial differential equations (PDEs). In the present article, we construct the exact traveling wave solutions of nonlinear evolution equations in mathematical physics via the (2 + 1)-dimensional breaking soliton equation by using two methods: namely, a further improved (G'/G)-expansion method, where G(ξ) satisfies the auxiliary ordinary differential equation (ODE) [G'(ξ)](2) = p G (2)(ξ) + q G (4)(ξ) + r G (6)(ξ); p, q and r are constants and the well known extended tanh-function method. We demonstrate, nevertheless some of the exact solutions bring out by these two methods are analogous, but they are not one and the same. It is worth mentioning that the first method has not been exercised anybody previously which gives further exact solutions than the second one. PACS numbers 02.30.Jr, 05.45.Yv, 02.30.Ik.

Approximate analytical solutions to the double-stance dynamics of the lossy spring-loaded inverted pendulum.

PubMed

Shahbazi, Mohammad; Saranlı, Uluç; Babuška, Robert; Lopes, Gabriel A D

2016-12-05

This paper introduces approximate time-domain solutions to the otherwise non-integrable double-stance dynamics of the 'bipedal' spring-loaded inverted pendulum (B-SLIP) in the presence of non-negligible damping. We first introduce an auxiliary system whose behavior under certain conditions is approximately equivalent to the B-SLIP in double-stance. Then, we derive approximate solutions to the dynamics of the new system following two different methods: (i) updated-momentum approach that can deal with both the lossy and lossless B-SLIP models, and (ii) perturbation-based approach following which we only derive a solution to the lossless case. The prediction performance of each method is characterized via a comprehensive numerical analysis. The derived representations are computationally very efficient compared to numerical integrations, and, hence, are suitable for online planning, increasing the autonomy of walking robots. Two application examples of walking gait control are presented. The proposed solutions can serve as instrumental tools in various fields such as control in legged robotics and human motion understanding in biomechanics.

Total chemical synthesis of proteins without HPLC purification† †Electronic supplementary information (ESI) available. See DOI: 10.1039/c6sc01883a Click here for additional data file.

PubMed Central

Loibl, S. F.; Harpaz, Z.; Zitterbart, R.

2016-01-01

The total chemical synthesis of proteins is a tedious and time-consuming endeavour. The typical steps involve solid phase synthesis of peptide thioesters and cysteinyl peptides, native chemical ligation (NCL) in solution, desulfurization or removal of ligation auxiliaries in the case of extended NCL as well as many intermediary and final HPLC purification steps. With an aim to facilitate and improve the throughput of protein synthesis we developed the first method for the rapid chemical total on-resin synthesis of proteins that proceeds without a single HPLC-purification step. The method relies on the combination of three orthogonal protein tags that allow sequential immobilization (via the N-terminal and C-terminal ends), extended native chemical ligation and release reactions. The peptide fragments to be ligated are prepared by conventional solid phase synthesis and used as crude materials in the subsequent steps. An N-terminal His6 unit permits selective immobilization of the full length peptide thioester onto Ni-NTA agarose beads. The C-terminal peptide fragment carries a C-terminal peptide hydrazide and an N-terminal 2-mercapto-2-phenyl-ethyl ligation auxiliary, which serves as a reactivity tag for the full length peptide. As a result, only full length peptides, not truncation products, react in the subsequent on-bead extended NCL. After auxiliary removal the ligation product is liberated into solution upon treatment with mild acid, and is concomitantly captured by an aldehyde-modified resin. This step allows the removal of the most frequently observed by-product in NCL chemistry, i.e. the hydrolysed peptide thioester (which does not contain a C-terminal peptide hydrazide). Finally, the target protein is released with diluted hydrazine or acid. We applied the method in the synthesis of 46 to 126 amino acid long MUC1 proteins comprising 2–6 copies of a 20mer tandem repeat sequence. Only three days were required for the parallel synthesis of 9 MUC1 proteins which were obtained in 8–33% overall yield with 90–98% purity despite the omission of HPLC purification. PMID:28451120

Broadband network on-line data acquisition system with web based interface for control and basic analysis

NASA Astrophysics Data System (ADS)

Polkowski, Marcin; Grad, Marek

2016-04-01

Passive seismic experiment "13BB Star" is operated since mid 2013 in northern Poland and consists of 13 broadband seismic stations. One of the elements of this experiment is dedicated on-line data acquisition system comprised of both client (station) side and server side modules with web based interface that allows monitoring of network status and provides tools for preliminary data analysis. Station side is controlled by ARM Linux board that is programmed to maintain 3G/EDGE internet connection, receive data from digitizer, send data do central server among with additional auxiliary parameters like temperatures, voltages and electric current measurements. Station side is controlled by set of easy to install PHP scripts. Data is transmitted securely over SSH protocol to central server. Central server is a dedicated Linux based machine. Its duty is receiving and processing all data from all stations including auxiliary parameters. Server side software is written in PHP and Python. Additionally, it allows remote station configuration and provides web based interface for user friendly interaction. All collected data can be displayed for each day and station. It also allows manual creation of event oriented plots with different filtering abilities and provides numerous status and statistic information. Our solution is very flexible and easy to modify. In this presentation we would like to share our solution and experience. National Science Centre Poland provided financial support for this work via NCN grant DEC-2011/02/A/ST10/00284.

Optimal analytic method for the nonlinear Hasegawa-Mima equation

NASA Astrophysics Data System (ADS)

Baxter, Mathew; Van Gorder, Robert A.; Vajravelu, Kuppalapalle

2014-05-01

The Hasegawa-Mima equation is a nonlinear partial differential equation that describes the electric potential due to a drift wave in a plasma. In the present paper, we apply the method of homotopy analysis to a slightly more general Hasegawa-Mima equation, which accounts for hyper-viscous damping or viscous dissipation. First, we outline the method for the general initial/boundary value problem over a compact rectangular spatial domain. We use a two-stage method, where both the convergence control parameter and the auxiliary linear operator are optimally selected to minimize the residual error due to the approximation. To do the latter, we consider a family of operators parameterized by a constant which gives the decay rate of the solutions. After outlining the general method, we consider a number of concrete examples in order to demonstrate the utility of this approach. The results enable us to study properties of the initial/boundary value problem for the generalized Hasegawa-Mima equation. In several cases considered, we are able to obtain solutions with extremely small residual errors after relatively few iterations are computed (residual errors on the order of 10-15 are found in multiple cases after only three iterations). The results demonstrate that selecting a parameterized auxiliary linear operator can be extremely useful for minimizing residual errors when used concurrently with the optimal homotopy analysis method, suggesting that this approach can prove useful for a number of nonlinear partial differential equations arising in physics and nonlinear mechanics.

Experimental analysis of multi-attribute decision-making based on Atanassov intuitionistic fuzzy sets: a discussion of anchor dependency and accuracy functions

NASA Astrophysics Data System (ADS)

Chen, Ting-Yu

2012-06-01

This article presents a useful method for relating anchor dependency and accuracy functions to multiple attribute decision-making (MADM) problems in the context of Atanassov intuitionistic fuzzy sets (A-IFSs). Considering anchored judgement with displaced ideals and solution precision with minimal hesitation, several auxiliary optimisation models have proposed to obtain the optimal weights of the attributes and to acquire the corresponding TOPSIS (the technique for order preference by similarity to the ideal solution) index for alternative rankings. Aside from the TOPSIS index, as a decision-maker's personal characteristics and own perception of self may also influence the direction in the axiom of choice, the evaluation of alternatives is conducted based on distances of each alternative from the positive and negative ideal alternatives, respectively. This article originates from Li's [Li, D.-F. (2005), 'Multiattribute Decision Making Models and Methods Using Intuitionistic Fuzzy Sets', Journal of Computer and System Sciences, 70, 73-85] work, which is a seminal study of intuitionistic fuzzy decision analysis using deduced auxiliary programming models, and deems it a benchmark method for comparative studies on anchor dependency and accuracy functions. The feasibility and effectiveness of the proposed methods are illustrated by a numerical example. Finally, a comparative analysis is illustrated with computational experiments on averaging accuracy functions, TOPSIS indices, separation measures from positive and negative ideal alternatives, consistency rates of ranking orders, contradiction rates of the top alternative and average Spearman correlation coefficients.

Active mass damper system for high-rise buildings using neural oscillator and position controller considering stroke limitation of the auxiliary mass

NASA Astrophysics Data System (ADS)

Hongu, J.; Iba, D.; Nakamura, M.; Moriwaki, I.

2016-04-01

This paper proposes a problem-solving method for the stroke limitation problem, which is related to auxiliary masses of active mass damper systems for high-rise buildings. The proposed method is used in a new simple control system for the active mass dampers mimicking the motion of bipedal mammals, which has a neural oscillator synchronizing with the acceleration response of structures and a position controller. In the system, the travel distance and direction of the auxiliary mass of the active mass damper is determined by reference to the output of the neural oscillator, and then, the auxiliary mass is transferred to the decided location by using a PID controller. The one of the purpose of the previouslyproposed system is stroke restriction problem avoidance of the auxiliary mass during large earthquakes by the determination of the desired value within the stroke limitation of the auxiliary mass. However, only applying the limited desired value could not rigorously restrict the auxiliary mass within the limitation, because the excessive inertia force except for the control force produced by the position controller affected on the motion of the auxiliary mass. In order to eliminate the effect on the auxiliary mass by the structural absolute acceleration, a cancellation method is introduced by adding a term to the control force of the position controller. We first develop the previously-proposed system for the active mass damper and the additional term for cancellation, and verity through numerical experiments that the new system is able to operate the auxiliary mass within the restriction during large earthquakes. Based on the comparison of the proposed system with the LQ system, a conclusion was drawn regarding which the proposed neuronal system with the additional term appears to be able to limit the stroke of the auxiliary mass of the AMD.

Interaction of Chemical Agents with Nanoscale Molecular Junctions

DTIC Science & Technology

2011-08-01

thiS burden to Department of Defense. Washilgton Headqualters Services. Directorate for lnformatie~n Operations and Reports (07()4.()188), 1215...The source of these contaminants were determined to be coming from the glovebox auxiliary vacuum pump, which normally operates continuously for...SAM- NHi NH2-SAM-Gold] molecular junction for analysis. In order to perform electron transport analysis of our nanoscale devices in a "real world

[Accidents with biological material in health care workers in 2 primary health care areas (1990-1999)].

PubMed

Hernández Navarrete, M J; Montes Villameriel, F J; Solano Bernad, V M; Sánchez Matienzo, D; del Val García, J L; Gil Montalbán, E; Arribas Llorente, J L

2001-09-15

To find out the exposures with biological material in health care workers in primary health care, registered in the biological accidents database from Preventive Medicine Service in Miguel Servet Universitary Hospital of Zaragoza. Descriptive study of a retrospective cohort. SITE: Primary health care, Areas II and V of Zaragoza.Participants. Workers in this areas, distributed by: physician, nursing staff, auxiliary, orderly, housekeeping staff, others. Data of: workers, accident, serologic source, worker protection and vaccinal status of hepatitis B. The incidence of accidents was 26 (period 1997-1999). Most proportion of accidents were declared by nursing (78%). The highest occupational incidence was in auxiliary (63 ). In 90,1% of the cases, the accident was needlestick injury. The source was known in 67,7% of cases. The accidents occurred in hands in 96,8% of cases, and only one third of workers carried gloves. Results obtained are similar with previous studies about this event. We must insist on the need to declare these accidents, providing more information and accessibility for the declaration to worker. Moreover, we must insist on the correct application in the health care field of the standard precautions, because almost 50% of accidents are evitable, and to increase hepatitis B vaccination covertures.

The Role of Auxiliary Subunits for the Functional Diversity of Voltage-Gated Calcium Channels

PubMed Central

Campiglio, Marta; Flucher, Bernhard E

2015-01-01

Voltage-gated calcium channels (VGCCs) represent the sole mechanism to convert membrane depolarization into cellular functions like secretion, contraction, or gene regulation. VGCCs consist of a pore-forming α1 subunit and several auxiliary channel subunits. These subunits come in multiple isoforms and splice-variants giving rise to a stunning molecular diversity of possible subunit combinations. It is generally believed that specific auxiliary subunits differentially regulate the channels and thereby contribute to the great functional diversity of VGCCs. If auxiliary subunits can associate and dissociate from pre-existing channel complexes, this would allow dynamic regulation of channel properties. However, most auxiliary subunits modulate current properties very similarly, and proof that any cellular calcium channel function is indeed modulated by the physiological exchange of auxiliary subunits is still lacking. In this review we summarize available information supporting a differential modulation of calcium channel functions by exchange of auxiliary subunits, as well as experimental evidence in support of alternative functions of the auxiliary subunits. At the heart of the discussion is the concept that, in their native environment, VGCCs function in the context of macromolecular signaling complexes and that the auxiliary subunits help to orchestrate the diverse protein–protein interactions found in these calcium channel signalosomes. Thus, in addition to a putative differential modulation of current properties, differential subcellular targeting properties and differential protein–protein interactions of the auxiliary subunits may explain the need for their vast molecular diversity. J. Cell. Physiol. 999: 00–00, 2015. © 2015 The Authors. Journal of Cellular Physiology Published by Wiley Periodicals, Inc. J. Cell. Physiol. 230: 2019–2031, 2015. © 2015 Wiley Periodicals, Inc. PMID:25820299

CRYOTE (Cryogenic Orbital Testbed) Concept

NASA Technical Reports Server (NTRS)

Gravlee, Mari; Kutter, Bernard; Wollen, Mark; Rhys, Noah; Walls, Laurie

2009-01-01

Demonstrating cryo-fluid management (CFM) technologies in space is critical for advances in long duration space missions. Current space-based cryogenic propulsion is viable for hours, not the weeks to years needed by space exploration and space science. CRYogenic Orbital TEstbed (CRYOTE) provides an affordable low-risk environment to demonstrate a broad array of critical CFM technologies that cannot be tested in Earth's gravity. These technologies include system chilldown, transfer, handling, health management, mixing, pressure control, active cooling, and long-term storage. United Launch Alliance is partnering with Innovative Engineering Solutions, the National Aeronautics and Space Administration, and others to develop CRYOTE to fly as an auxiliary payload between the primary payload and the Centaur upper stage on an Atlas V rocket. Because satellites are expensive, the space industry is largely risk averse to incorporating unproven systems or conducting experiments using flight hardware that is supporting a primary mission. To minimize launch risk, the CRYOTE system will only activate after the primary payload is separated from the rocket. Flying the testbed as an auxiliary payload utilizes Evolved Expendable Launch Vehicle performance excess to cost-effectively demonstrate enhanced CFM.

Determination of Stress Coefficient Terms in Cracked Solids for Monoclinic Materials with Plane Symmetry at x3 = 0

NASA Technical Reports Server (NTRS)

Yuan, F. G.

1998-01-01

Determination of all the coefficients in the crack tip field expansion for monoclinic materials under two-dimensional deformation is presented in this report. For monoclinic materials with a plane of material symmetry at x(sub 3) = 0, the in-plane deformation is decoupled from the anti-plane deformation. In the case of in-plane deformation, utilizing conservation laws of elasticity and Betti's reciprocal theorem, together with selected auxiliary fields, T-stress and third-order stress coefficients near the crack tip are evaluated first from path-independent line integrals. To determine the T-stress terms using the J-integral and Betti's reciprocal work theorem, auxiliary fields under a concentrated force and moment acting at the crack tip are used respectively. Through the use of Stroh formalism in anisotropic elasticity, analytical expressions for all the coefficients including the stress intensity factors are derived in a compact form that has surprisingly simple structure in terms of the Barnett-Lothe tensors, L. The solution forms for degenerated materials, orthotropic, and isotropic materials are presented.

Puerto Rico Experimental Model Dental Auxiliary Training Program. The Comprehensive Report, October 22, 1976-February 24, 1980.

ERIC Educational Resources Information Center

Puerto Rico Univ., San Juan. School of Dentistry.

The Dental Auxiliary Department of the University of Puerto Rico designed a career option dental auxiliary training program which is a step ladder program with three exit points over a period of two academic years. The first option is a six-month track to train a traditional chairside dental auxiliary. The second option is a nine-month track to…

High Input Voltage, Silicon Carbide Power Processing Unit Performance Demonstration

NASA Technical Reports Server (NTRS)

Bozak, Karin E.; Pinero, Luis R.; Scheidegger, Robert J.; Aulisio, Michael V.; Gonzalez, Marcelo C.; Birchenough, Arthur G.

2015-01-01

A silicon carbide brassboard power processing unit has been developed by the NASA Glenn Research Center in Cleveland, Ohio. The power processing unit operates from two sources: a nominal 300 Volt high voltage input bus and a nominal 28 Volt low voltage input bus. The design of the power processing unit includes four low voltage, low power auxiliary supplies, and two parallel 7.5 kilowatt (kW) discharge power supplies that are capable of providing up to 15 kilowatts of total power at 300 to 500 Volts (V) to the thruster. Additionally, the unit contains a housekeeping supply, high voltage input filter, low voltage input filter, and master control board, such that the complete brassboard unit is capable of operating a 12.5 kilowatt Hall effect thruster. The performance of the unit was characterized under both ambient and thermal vacuum test conditions, and the results demonstrate exceptional performance with full power efficiencies exceeding 97%. The unit was also tested with a 12.5kW Hall effect thruster to verify compatibility and output filter specifications. With space-qualified silicon carbide or similar high voltage, high efficiency power devices, this would provide a design solution to address the need for high power electric propulsion systems.

Visual communications with side information via distributed printing channels: extended multimedia and security perspectives

NASA Astrophysics Data System (ADS)

Voloshynovskiy, Sviatoslav V.; Koval, Oleksiy; Deguillaume, Frederic; Pun, Thierry

2004-06-01

In this paper we address visual communications via printing channels from an information-theoretic point of view as communications with side information. The solution to this problem addresses important aspects of multimedia data processing, security and management, since printed documents are still the most common form of visual information representation. Two practical approaches to side information communications for printed documents are analyzed in the paper. The first approach represents a layered joint source-channel coding for printed documents. This approach is based on a self-embedding concept where information is first encoded assuming a Wyner-Ziv set-up and then embedded into the original data using a Gel'fand-Pinsker construction and taking into account properties of printing channels. The second approach is based on Wyner-Ziv and Berger-Flynn-Gray set-ups and assumes two separated communications channels where an appropriate distributed coding should be elaborated. The first printing channel is considered to be a direct visual channel for images ("analog" channel with degradations). The second "digital channel" with constrained capacity is considered to be an appropriate auxiliary channel. We demonstrate both theoretically and practically how one can benefit from this sort of "distributed paper communications".

42. AUXILIARY CHAMBER, VIEW LOOKING EAST FROM WEST END, OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. AUXILIARY CHAMBER, VIEW LOOKING EAST FROM WEST END, OF AUXILIARY PIPING, STEAM, FEEDWATER PIPING (LOCATION BBB) - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

33 CFR 5.47 - Auxiliary ensign.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the Auxiliary ensign is medium blue (Coast Guard blue) with a broad diagonal white slash upon which a matching blue Coast Guard Auxiliary emblem is centered. The white slash shall be at a 70 degree angle...

33 CFR 5.47 - Auxiliary ensign.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the Auxiliary ensign is medium blue (Coast Guard blue) with a broad diagonal white slash upon which a matching blue Coast Guard Auxiliary emblem is centered. The white slash shall be at a 70 degree angle...

33 CFR 5.47 - Auxiliary ensign.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the Auxiliary ensign is medium blue (Coast Guard blue) with a broad diagonal white slash upon which a matching blue Coast Guard Auxiliary emblem is centered. The white slash shall be at a 70 degree angle...

33 CFR 5.47 - Auxiliary ensign.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the Auxiliary ensign is medium blue (Coast Guard blue) with a broad diagonal white slash upon which a matching blue Coast Guard Auxiliary emblem is centered. The white slash shall be at a 70 degree angle...

33 CFR 5.47 - Auxiliary ensign.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the Auxiliary ensign is medium blue (Coast Guard blue) with a broad diagonal white slash upon which a matching blue Coast Guard Auxiliary emblem is centered. The white slash shall be at a 70 degree angle...

AdS5 solutions from M5-branes on Riemann surface and D6-branes sources

DOE PAGES

Bah, Ibrahima

2015-09-24

Here, we describe the gravity duals of four-dimensional N = 1 superconformal field theories obtained by wrapping M5-branes on a punctured Riemann surface. The internal geometry, normal to the AdS 5 factor, generically preserves two U(1)s, with generators (J +, J –), that are fibered over the Riemann surface. The metric is governed by a single potential that satisfies a version of the Monge-Ampère equation. The spectrum of N = 1 punctures is given by the set of supersymmetric sources of the potential that are localized on the Riemann surface and lead to regular metrics near a puncture. We usemore » this system to study a class of punctures where the geometry near the sources corresponds to M-theory description of D6-branes. These carry a natural (p, q) label associated to the circle dual to the killing vector pJ + + qJ – which shrinks near the source. In the generic case the world volume of the D6-branes is AdS 5 × S 2 and they locally preserve N = 2 supersymmetry. When p = –q, the shrinking circle is dual to a flavor U(1). The metric in this case is non-degenerate only when there are co-dimension one sources obtained by smearing M5-branes that wrap the AdS 5 factor and the circle dual the superconformal R-symmetry. The D6-branes are extended along the AdS 5 and on cups that end on the co-dimension one branes. In the special case when the shrinking circle is dual to the R-symmetry, the D6-branes are extended along the AdS 5 and wrap an auxiliary Riemann surface with an arbitrary genus. When the Riemann surface is compact with constant curvature, the system is governed by a Monge-Ampère equation.« less

Design and scope of impact of auxiliary lanes : technical report.

DOT National Transportation Integrated Search

2014-06-01

For decades, Texas Department of Transportation districts have constructed auxiliary lanes to support interchange : ramp operations and to resolve congestion proximate to freeway entrance and exit ramps. While auxiliary lanes are : built throughout T...

Optimized auxiliary basis sets for density fitted post-Hartree-Fock calculations of lanthanide containing molecules

NASA Astrophysics Data System (ADS)

Chmela, Jiří; Harding, Michael E.

2018-06-01

Optimised auxiliary basis sets for lanthanide atoms (Ce to Lu) for four basis sets of the Karlsruhe error-balanced segmented contracted def2 - series (SVP, TZVP, TZVPP and QZVPP) are reported. These auxiliary basis sets enable the use of the resolution-of-the-identity (RI) approximation in post Hartree-Fock methods - as for example, second-order perturbation theory (MP2) and coupled cluster (CC) theory. The auxiliary basis sets are tested on an enlarged set of about a hundred molecules where the test criterion is the size of the RI error in MP2 calculations. Our tests also show that the same auxiliary basis sets can be used together with different effective core potentials. With these auxiliary basis set calculations of MP2 and CC quality can now be performed efficiently on medium-sized molecules containing lanthanides.

Learning classification with auxiliary probabilistic information

PubMed Central

Nguyen, Quang; Valizadegan, Hamed; Hauskrecht, Milos

2012-01-01

Finding ways of incorporating auxiliary information or auxiliary data into the learning process has been the topic of active data mining and machine learning research in recent years. In this work we study and develop a new framework for classification learning problem in which, in addition to class labels, the learner is provided with an auxiliary (probabilistic) information that reflects how strong the expert feels about the class label. This approach can be extremely useful for many practical classification tasks that rely on subjective label assessment and where the cost of acquiring additional auxiliary information is negligible when compared to the cost of the example analysis and labelling. We develop classification algorithms capable of using the auxiliary information to make the learning process more efficient in terms of the sample complexity. We demonstrate the benefit of the approach on a number of synthetic and real world data sets by comparing it to the learning with class labels only. PMID:25309141

Alternative auxiliary fields for chiral multiplets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nishino, Hitoshi; Rajpoot, Subhash

We study 3-form auxiliary field formulation for chiral multiplets in the Wess-Zumino model. The conventional auxiliary fields F and G are replaced by their Hodge duals K{sub {mu}}{sub {nu}}{sub {rho}}{sub {sigma}} and H{sub {mu}}{sub {nu}}{sub {rho}}{sub {sigma}} which are the field strengths of the 3-form potential auxiliary fields G{sub {mu}}{sub {nu}}{sub {rho}} and F{sub {mu}}{sub {nu}}{sub {rho}}. Even though duality transformations connect these two formulations, there exist certain differences from the conventional formulation. When boundary conditions are taken into account, the field equations in the 3-form formulation are equivalent to the conventional ones, while our Lagrangian is not. We alsomore » show that the new field strengths acquire generalized Chern-Simons terms. The O'Raifeartaigh mechanism works for spontaneous supersymmetry breaking also in the 3-form auxiliary field formulation via the boundary conditions on the 3-form auxiliary fields.« less

Goal programming for cyclical auxiliary police scheduling at UiTM Cawangan Perlis

NASA Astrophysics Data System (ADS)

Mustapar, Wasilatul Effah; Nasir, Diana Sirmayunie Mohd; Nor, Nor Azriani Mohamad; Abas, Sharifah Fhahriyah Syed

2017-11-01

Constructing a good and fair schedule for shift workers poses a great challenge as it requires a lot of time and effort. In this study, goal programming has been applied on scheduling to achieve the hard and soft constraints for a cyclical schedule that would ease the head of auxiliary police at building new schedules. To accomplish this goal, shift types were assigned in order to provide a fair schedule that takes into account the auxiliary police's policies and preferences. The model was run using Lingo software. Three out of four goals set for the study were achieved. In addition, the results considered an equal allocation for every auxiliary police, namely 70% for total duty and 30% for the day. Furthermore, the schedule was able to cyclically generate another 10 sets schedule. More importantly, the model has provided unbiased scheduling of auxiliary policies which led to high satisfaction in auxiliary police management.

Improved Aqueous Solubility and Antihypercholesterolemic Activity of Ezetimibe on Formulating with Hydroxypropyl-β-Cyclodextrin and Hydrophilic Auxiliary Substances.

PubMed

Srivalli, Kale Mohana Raghava; Mishra, Brahmeshwar

2016-04-01

The purpose of this study was to improve the aqueous solubility, dissolution, and pharmacodynamic properties of a BCS class II drug, ezetimibe (Eze) by preparing ternary cyclodextrin complex systems. We investigated the potential synergistic effect of two novel hydrophilic auxiliary substances, D-α-tocopheryl polyethylene glycol 1000 succinate (TPGS) and L-ascorbic acid-2-glucoside (AA2G) on hydroxypropyl-β-cyclodextrin (HPBCD) solubilization of poorly water-soluble hypocholesterolemic drug, Eze. In solution state, the binary and ternary systems were analyzed by phase solubility studies and Job's plot. The solid complexes prepared by freeze-drying were characterized by Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), powder X-ray diffraction (XRD), nuclear magnetic resonance (NMR), and scanning electron microscopy (SEM). The log P values, aqueous solubility, dissolution, and antihypercholesterolemic activity of all systems were studied. The analytical techniques confirmed the formation of inclusion complexes in the binary and ternary systems. HPBCD complexation significantly (p < 0.05) reduced the log P and improved the solubility, dissolution, and hypocholesterolemic properties of Eze, and the addition of ternary component produced further significant improvement (p < 0.05) even compared to binary system. The remarkable reduction in log P and enhancement in solubility, dissolution, and antihypercholesterolemic activity due to the addition of TPGS or AA2G may be attributed to enhanced wetting, dispersibility, and complete amorphization. The use of TPGS or AA2G as ternary hydrophilic auxiliary substances improved the HPBCD solubilization and antihypercholesterolemic activity of Eze.

Focal Mechanism of a Catastrophic Earthquake of the Last Rococo Period (1783) in Southern Italy Retrieved by Inverting Historical Information on Damage

NASA Astrophysics Data System (ADS)

Sirovich, L.; Pettenati, F.

2007-05-01

Using geophysical inversion to discover the fault source of a blind earthquake, that took place before the invention of the seismograph, seemed impossible. We demonstrated that sometimes it is possible using our simplified KF model (Sirovich, 1996) through automatic genetic inversion (Gentile et al., 2004 in BSSA; Sirovich and Pettenati, 2004 in JGR), and determined it conclusively by treating the Coalinga 1983, Loma Prieta 1989, and Northridge 1994 earthquakes (Pettenati and Sirovich, 2007 in BSSA). KF is able to simulate the body-wave radiation from a linear source, and eleven source parameters are retrieved: the three nucleation coordinates, the fault-plane solution, the seismic moment, the rupture velocities and lengths along-strike and anti-strike, the shear wave velocity in the half-space. To find the minima on the hypersurface of the residuals in the multi-parameter model space, we use a genetic process with niching since we have already shown that the problem is bimodal for pure dip-slip mechanisms. The objective function of the nonlinear inversion is the sum of the squared residuals (calculated-minus-observed intensity at all sites). Here, we use the very good intensity data provided in the MCS scale by the INGV of Italy for the M 6.9 earthquake of Feb. 5, 1783 (see the Italian intensity data bank on http:emidius.mi.ingv.it/DOM/consultazione.html). The data of 1783 were created by seismologists and historians who interpreted the reports of the time and many other historical sources. Given the limitations of the KF approach, we limited our inversion to a square area of 200 by 200 km around the most heavily damaged zone. 341 surveyed towns and hamlets received intensity degrees by INGV (we discarded 6 of them as statistical outliers according to the classical Chauvenet method). Thus, 335 data were inverted. The match between experimental and synthetic isoseismals is really noteworthy. The found mechanism is almost pure dip-slip and, thus, the problem is bimodal. In fact, two source models score almost the same objective function, and they coincide with the auxiliary planes of the same solution. The best source is: nucleation latitude [degrees] 38.28, longitude 15.95, depth 13.1 km; strike angle 210, dip 31, rake 269(±180); seismic moment 2.7 * 10e19 Nm, 3.1 km/s rupture velocity along-strike (3.3 anti-strike), 22.3 km rupture length along-strike (20.7 anti-strike), 3.9 km/s shear wave velocity in the half-space. The second solution, having the same nucleation coordinates and a one-point difference in the objective function (117 against 116) is: strike angle 30, dip 60, rake 270(±180); seismic moment 2.6 * 10e19 Nm, 3.3 km/s rupture velocity along-strike (3.0 anti-strike), 19.4 km rupture length along-strike (21.9 anti-strike), 3.9 km/s shear wave velocity in the half-space. Note the symmetry with the former solution. In other words, we find one fault source having a low-angle dip toward the Tyrrhenian Sea; its virtual intersection with the topographical surface should be found close to the Jonian coast. On the contrary, its symmetric solution strikes SW, has a high-angle dip toward the Jonian Sea, and the fault should outcrop close to the Tyrrhenian coast. Both sources are compatible with the orientation of the principal tectonic structures in the area, however. The final choice between them will hopefully come from tectonic interpretation. This kind of study seems especially promising for southern Europe where a lot of documents on seismic damage caused by old earthquakes exist.

Prolongation structures of nonlinear evolution equations

NASA Technical Reports Server (NTRS)

Wahlquist, H. D.; Estabrook, F. B.

1975-01-01

A technique is developed for systematically deriving a 'prolongation structure' - a set of interrelated potentials and pseudopotentials - for nonlinear partial differential equations in two independent variables. When this is applied to the Korteweg-de Vries equation, a new infinite set of conserved quantities is obtained. Known solution techniques are shown to result from the discovery of such a structure: related partial differential equations for the potential functions, linear 'inverse scattering' equations for auxiliary functions, Backlund transformations. Generalizations of these techniques will result from the use of irreducible matrix representations of the prolongation structure.

Nonlinear inhomogeneous Fokker-Planck equations: Entropy and free-energy time evolution.

PubMed

Sicuro, Gabriele; Rapčan, Peter; Tsallis, Constantino

2016-12-01

We extend a recently introduced free-energy formalism for homogeneous Fokker-Planck equations to a wide, and physically appealing, class of inhomogeneous nonlinear Fokker-Planck equations. In our approach, the free-energy functional is expressed in terms of an entropic functional and an auxiliary potential, both derived from the coefficients of the equation. With reference to the introduced entropic functional, we discuss the entropy production in a relaxation process towards equilibrium. The properties of the stationary solutions of the considered Fokker-Planck equations are also discussed.

Use of an auxiliary basis set to describe the polarization in the fragment molecular orbital method

NASA Astrophysics Data System (ADS)

Fedorov, Dmitri G.; Kitaura, Kazuo

2014-03-01

We developed a dual basis approach within the fragment molecular orbital formalism enabling efficient and accurate use of large basis sets. The method was tested on water clusters and polypeptides and applied to perform geometry optimization of chignolin (PDB: 1UAO) in solution at the level of DFT/6-31++G∗∗, obtaining a structure in agreement with experiment (RMSD of 0.4526 Å). The polarization in polypeptides is discussed with a comparison of the α-helix and β-strand.

Study on the key technology of grain logistics tracking system

NASA Astrophysics Data System (ADS)

Zhen, Tong; Ge, Hongyi; Jiang, Yuying; Che, Yi

2010-07-01

In recent year, with the rapid development of GIS technology, more and more programming problems depend on the GIS technology and professional model system. The solution of auxiliary programming problem by using GIS technology, which has become very popular. GIS is an important tool and technology, that captures, stores, analyzes, manages, and presents data that are linked to location. A grain logistics distribution system based on GIS is established, which provides a visualization scheme during the process of grain circulation and supports users making decision and analyzing for grain logistics enterprise.

45. DETAIL VIEW OF AUXILIARY BUILDING AT UPPER END OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

45. DETAIL VIEW OF AUXILIARY BUILDING AT UPPER END OF WEST WALL, SHOWING RECESSES FOR AUXILIARY LOCK LIFT GATE LEAVES, LOOKING NORTHWEST - Upper Mississippi River 9-Foot Channel Project, Lock & Dam 27, Granite City, Madison County, IL

Wigner Transport Simulation of Resonant Tunneling Diodes with Auxiliary Quantum Wells

NASA Astrophysics Data System (ADS)

Lee, Joon-Ho; Shin, Mincheol; Byun, Seok-Joo; Kim, Wangki

2018-03-01

Resonant-tunneling diodes (RTDs) with auxiliary quantum wells ( e.g., emitter prewell, subwell, and collector postwell) are studied using a Wigner transport equation (WTE) discretized by a thirdorder upwind differential scheme. A flat-band potential profile is used for the WTE simulation. Our calculations revealed functions of the auxiliary wells as follows: The prewell increases the current density ( J) and the peak voltage ( V p ) while decreasing the peak-to-valley current ratio (PVCR), and the postwell decreases J while increasing the PVCR. The subwell affects J and PVCR, but its main effect is to decrease V p . When multiple auxiliary wells are used, each auxiliary well contributes independently to the transport without producing side effects.

Poincaré chaos and unpredictable functions

NASA Astrophysics Data System (ADS)

Akhmet, Marat; Fen, Mehmet Onur

2017-07-01

The results of this study are continuation of the research of Poincaré chaos initiated in the papers (M. Akhmet and M.O. Fen, Commun Nonlinear Sci Numer Simulat 40 (2016) 1-5; M. Akhmet and M.O. Fen, Turk J Math, doi:10.3906/mat-1603-51, in press). We focus on the construction of an unpredictable function, continuous on the real axis. As auxiliary results, unpredictable orbits for the symbolic dynamics and the logistic map are obtained. By shaping the unpredictable function as well as Poisson function we have performed the first step in the development of the theory of unpredictable solutions for differential and discrete equations. The results are preliminary ones for deep analysis of chaos existence in differential and hybrid systems. Illustrative examples concerning unpredictable solutions of differential equations are provided.

On the formation of fold-type oscillation marks in the continuous casting of steel.

PubMed

Vynnycky, M; Saleem, S; Devine, K M; Florio, B J; Mitchell, S L; O'Brien, S B G

2017-06-01

Asymptotic methods are employed to revisit an earlier model for oscillation-mark formation in the continuous casting of steel. A systematic non-dimensionalization of the governing equations, which was not carried out previously, leads to a model with 12 dimensionless parameters. Analysis is provided in the same parameter regime as for the earlier model, and surprisingly simple analytical solutions are found for the oscillation-mark profiles; these are found to agree reasonably well with the numerical solution in the earlier model and very well with fold-type oscillation marks that have been obtained in more recent experimental work. The benefits of this approach, when compared with time-consuming numerical simulations, are discussed in the context of auxiliary models for macrosegregation and thermomechanical stresses and strains.

On the formation of fold-type oscillation marks in the continuous casting of steel

PubMed Central

Saleem, S.; Devine, K. M.; Florio, B. J.; Mitchell, S. L.; O’Brien, S. B. G.

2017-01-01

Asymptotic methods are employed to revisit an earlier model for oscillation-mark formation in the continuous casting of steel. A systematic non-dimensionalization of the governing equations, which was not carried out previously, leads to a model with 12 dimensionless parameters. Analysis is provided in the same parameter regime as for the earlier model, and surprisingly simple analytical solutions are found for the oscillation-mark profiles; these are found to agree reasonably well with the numerical solution in the earlier model and very well with fold-type oscillation marks that have been obtained in more recent experimental work. The benefits of this approach, when compared with time-consuming numerical simulations, are discussed in the context of auxiliary models for macrosegregation and thermomechanical stresses and strains. PMID:28680666

Density-functional expansion methods: Grand challenges.

PubMed

Giese, Timothy J; York, Darrin M

2012-03-01

We discuss the source of errors in semiempirical density functional expansion (VE) methods. In particular, we show that VE methods are capable of well-reproducing their standard Kohn-Sham density functional method counterparts, but suffer from large errors upon using one or more of these approximations: the limited size of the atomic orbital basis, the Slater monopole auxiliary basis description of the response density, and the one- and two-body treatment of the core-Hamiltonian matrix elements. In the process of discussing these approximations and highlighting their symptoms, we introduce a new model that supplements the second-order density-functional tight-binding model with a self-consistent charge-dependent chemical potential equalization correction; we review our recently reported method for generalizing the auxiliary basis description of the atomic orbital response density; and we decompose the first-order potential into a summation of additive atomic components and many-body corrections, and from this examination, we provide new insights and preliminary results that motivate and inspire new approximate treatments of the core-Hamiltonian.

Design of a nuclear isotope heat source assembly for a spaceborne mini-Brayton power module.

NASA Technical Reports Server (NTRS)

Wein, D.; Gorland, S. H.

1973-01-01

Results of a study to develop a feasible design definition of a heat source assembly (HSA) for use in nominal 500-, 1200-, or 2000-W(e) mini-Brayton spacecraft power systems. The HSA is a modular design which is used either as a single unit to provide thermal energy to the 500-W(e) mini-Brayton power module or in parallel with one or two additional HSAs for the 1200- or 2000-W(e) power module systems. Principal components consist of a multihundred watt RTG isotope heat source, a heat source heat exchanger which transfers the thermal energy from the heat source to the mini-Brayton power conversion system, an auxiliary cooling system which provides requisite cooling during nonoperation of the power conversion module and an emergency cooling system which precludes accidental release of isotope fuel in the event of system failure.

Scientific Platform as a Service - Tools and solutions for efficient access to and analysis of oceanographic data

NASA Astrophysics Data System (ADS)

Vines, Aleksander; Hansen, Morten W.; Korosov, Anton

2017-04-01

Existing infrastructure international and Norwegian projects, e.g., NorDataNet, NMDC and NORMAP, provide open data access through the OPeNDAP protocol following the conventions for CF (Climate and Forecast) metadata, designed to promote the processing and sharing of files created with the NetCDF application programming interface (API). This approach is now also being implemented in the Norwegian Sentinel Data Hub (satellittdata.no) to provide satellite EO data to the user community. Simultaneously with providing simplified and unified data access, these projects also seek to use and establish common standards for use and discovery metadata. This then allows development of standardized tools for data search and (subset) streaming over the internet to perform actual scientific analysis. A combinnation of software tools, which we call a Scientific Platform as a Service (SPaaS), will take advantage of these opportunities to harmonize and streamline the search, retrieval and analysis of integrated satellite and auxiliary observations of the oceans in a seamless system. The SPaaS is a cloud solution for integration of analysis tools with scientific datasets via an API. The core part of the SPaaS is a distributed metadata catalog to store granular metadata describing the structure, location and content of available satellite, model, and in situ datasets. The analysis tools include software for visualization (also online), interactive in-depth analysis, and server-based processing chains. The API conveys search requests between system nodes (i.e., interactive and server tools) and provides easy access to the metadata catalog, data repositories, and the tools. The SPaaS components are integrated in virtual machines, of which provisioning and deployment are automatized using existing state-of-the-art open-source tools (e.g., Vagrant, Ansible, Docker). The open-source code for scientific tools and virtual machine configurations is under version control at https://github.com/nansencenter/, and is coupled to an online continuous integration system (e.g., Travis CI).

Ionic contribution to the self-potential signals associated with a redox front.

PubMed

Revil, A; Trolard, F; Bourrié, G; Castermant, J; Jardani, A; Mendonça, C A

2009-10-13

In contaminant plumes or in the case of ore bodies, a source current density is produced at depth in response to the presence of a gradient of the redox potential. Two charge carriers can exist in such a medium: electrons and ions. Two contributions to the source current density are associated with these charge carriers (i) the gradient of the chemical potential of the ionic species and (ii) the gradient of the chemical potential of the electrons (i.e., the gradient of the redox potential). We ran a set of experiments in which a geobattery is generated using electrolysis reactions of a pore water solution containing iron. A DC power supply is used to impose a difference of electrical potential of 3 V between a working platinum electrode (anode) and an auxiliary platinum electrode (cathode). Both electrodes inserted into a tank filled with a well-calibrated sand infiltrated by a (0.01 mol L(-1) KCl+0.0035 mol L(-)(1) FeSO(4)) solution. After the direct current is turned off, we follow the pH, the redox potential, and the self-potential at several time intervals. The self-potential anomalies amount to a few tens of millivolts after the current is turned off and decreases over time. After several days, all the redox-active compounds produced initially by the electrolysis reactions are consumed through chemical reactions and the self-potential anomalies fall to zero. The resulting self-potential anomalies are shown to be much weaker than the self-potential anomalies observed in the presence of an electronic conductor in the laboratory or in the field. In the presence of a biotic or an abiotic electronic conductor, the self-potential anomalies can amount to a few hundred millivolts. These observations point out indirectly the potential role of bacteria forming biofilms in the transfer of electrons through sharp redox potential gradient in contaminant plumes that are rich in organic matter.

Development of Auxiliaries in Young Children Learning African American English.

PubMed

Newkirk-Turner, Brandi L; Oetting, Janna B; Stockman, Ida J

2016-07-01

We examined language samples of young children learning African American English (AAE) to determine if and when their use of auxiliaries shows dialect-universal and dialect-specific effects. The data were longitudinal language samples obtained from two children, ages 18 to 36 months, and three children, ages 33 to 51 months. Dialect-universal analyses examined age of first form and early uses of BE, DO, and modal auxiliaries. Dialect-specific analyses focused on rates of overt marking by auxiliary type and syntactic construction and for BE by surface form and succeeding element. Initial production of auxiliaries occurred between 19 and 24 months. The children's forms were initially restricted and produced in syntactically simple constructions. Over time, they were expanded in ways that showed their rates of marking to vary by auxiliary type, their rates of BE and DO marking to vary by syntactic construction, and their rates of BE marking to vary by surface form and succeeding element. Development of auxiliaries by young children learning AAE shows both dialect-universal and dialect-specific effects. The findings are presented within a development chart to guide clinicians in the assessment of children learning AAE and in the treatment of AAE-speaking children with language impairment.

Airport Landside. Volume IV. Appendix A. ALSIM AUXILIARY and MAIN Programs.

DOT National Transportation Integrated Search

1982-06-01

This Appendix describes the Program Logic of the Airport Landside Simulation Model (ALSIM) AUXILIARY and MAIN Programs. Both programs are written in GPSS-V. The AUXILIARY program is operated prior to the MAIN Program to create GPSS transactions repre...

Influence of backup bearings and support structure dynamics on the behavior of rotors with active supports

NASA Technical Reports Server (NTRS)

Flowers, George T.

1995-01-01

Progress made in the current year is listed, and the following papers are included in the appendix: Steady-State Dynamic Behavior of an Auxiliary Bearing Supported Rotor System; Dynamic Behavior of a Magnetic Bearing Supported Jet Engine Rotor with Auxiliary Bearings; Dynamic Modelling and Response Characteristics of a Magnetic Bearing Rotor System with Auxiliary Bearings; and Synchronous Dynamics of a Coupled Shaft/Bearing/Housing System with Auxiliary Support from a Clearance Bearing: Analysis and Experiment.

One cutting plane algorithm using auxiliary functions

NASA Astrophysics Data System (ADS)

Zabotin, I. Ya; Kazaeva, K. E.

2016-11-01

We propose an algorithm for solving a convex programming problem from the class of cutting methods. The algorithm is characterized by the construction of approximations using some auxiliary functions, instead of the objective function. Each auxiliary function bases on the exterior penalty function. In proposed algorithm the admissible set and the epigraph of each auxiliary function are embedded into polyhedral sets. In connection with the above, the iteration points are found by solving linear programming problems. We discuss the implementation of the algorithm and prove its convergence.

Carbon catabolite repression and cell dispersal affect degradation of the xenobiotic compound 3,4-dichloroaniline in Comamonas testosteroni WDL7 biofilms.

PubMed

Horemans, Benjamin; Breugelmans, Philip; Hofkens, Johan; Springael, Dirk

2017-03-01

Organic pollutant degrading biofilms in natural ecosystems and water treatment systems are often exposed to other carbon sources in addition to the pollutant. The availability of auxiliary carbon sources can lead to surplus biomass growth, changes in biofilm structure and carbon catabolite repression (CCR) which together will affect pollutant degradation rate and efficiency of the system. To understand the interplay between these processes, continuous biofilms of the 3,4-dichloroaniline (3,4-DCA) degrading Comamonas testosteroni WDL7-RFP were grown in single- and dual-substrate conditions with 3,4-DCA and/or citrate and reciprocal effects on 3,4-DCA/citrate degradation, biofilm biomass and biofilm structure were examined. The main mechanism affecting 3,4-DCA degradation in biofilms in dual-substrate conditions was citrate-mediated CCR as reflected by a decrease in specific 3,4-DCA degrading activity. Growth on citrate partially compensated for the lowered specific 3,4-DCA degradation activity under dual substrate conditions but not to the extent expected from growth observed under single-substrate conditions with citrate. This was explained by higher residual 3,4-DCA concentrations in the presence of citrate that increased cell dispersal in the biofilms. Our results show hampered pollutant removal in biofilms due to a complex interplay of auxiliary organic C source utilization for growth affecting the specific pollutant degradation rate and changes in cell physiology due to increased exposure to the pollutant as a result of lowered pollutant degradation rates. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Study of electrical and chemical propulsion systems for auxiliary propulsion of large space systems, volume 2

NASA Technical Reports Server (NTRS)

Smith, W. W.

1981-01-01

The five major tasks of the program are reported. Task 1 is a literature search followed by selection and definition of seven generic spacecraft classes. Task 2 covers the determination and description of important disturbance effects. Task 3 applies the disturbances to the generic spacecraft and adds maneuver and stationkeeping functions to define total auxiliary propulsion systems requirements for control. The important auxiliary propulsion system characteristics are identified and sensitivities to control functions and large space system characteristics determined. In Task 4, these sensitivities are quantified and the optimum auxiliary propulsion system characteristics determined. Task 5 compares the desired characteristics with those available for both electrical and chemical auxiliary propulsion systems to identify the directions technology advances should take.

The use of auxiliary variables in capture-recapture and removal experiments

USGS Publications Warehouse

Pollock, K.H.; Hines, J.E.; Nichols, J.D.

1984-01-01

The dependence of animal capture probabilities on auxiliary variables is an important practical problem which has not been considered in the development of estimation procedures for capture-recapture and removal experiments. In this paper the linear logistic binary regression model is used to relate the probability of capture to continuous auxiliary variables. The auxiliary variables could be environmental quantities such as air or water temperature, or characteristics of individual animals, such as body length or weight. Maximum likelihood estimators of the population parameters are considered for a variety of models which all assume a closed population. Testing between models is also considered. The models can also be used when one auxiliary variable is a measure of the effort expended in obtaining the sample.

The iFlow modelling framework v2.4: a modular idealized process-based model for flow and transport in estuaries

NASA Astrophysics Data System (ADS)

Dijkstra, Yoeri M.; Brouwer, Ronald L.; Schuttelaars, Henk M.; Schramkowski, George P.

2017-07-01

The iFlow modelling framework is a width-averaged model for the systematic analysis of the water motion and sediment transport processes in estuaries and tidal rivers. The distinctive solution method, a mathematical perturbation method, used in the model allows for identification of the effect of individual physical processes on the water motion and sediment transport and study of the sensitivity of these processes to model parameters. This distinction between processes provides a unique tool for interpreting and explaining hydrodynamic interactions and sediment trapping. iFlow also includes a large number of options to configure the model geometry and multiple choices of turbulence and salinity models. Additionally, the model contains auxiliary components, including one that facilitates easy and fast sensitivity studies. iFlow has a modular structure, which makes it easy to include, exclude or change individual model components, called modules. Depending on the required functionality for the application at hand, modules can be selected to construct anything from very simple quasi-linear models to rather complex models involving multiple non-linear interactions. This way, the model complexity can be adjusted to the application. Once the modules containing the required functionality are selected, the underlying model structure automatically ensures modules are called in the correct order. The model inserts iteration loops over groups of modules that are mutually dependent. iFlow also ensures a smooth coupling of modules using analytical and numerical solution methods. This way the model combines the speed and accuracy of analytical solutions with the versatility of numerical solution methods. In this paper we present the modular structure, solution method and two examples of the use of iFlow. In the examples we present two case studies, of the Yangtze and Scheldt rivers, demonstrating how iFlow facilitates the analysis of model results, the understanding of the underlying physics and the testing of parameter sensitivity. A comparison of the model results to measurements shows a good qualitative agreement. iFlow is written in Python and is available as open source code under the LGPL license.

47 CFR 80.290 - Auxiliary receiving antenna.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 5 2013-10-01 2013-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not available...

47 CFR 80.290 - Auxiliary receiving antenna.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 5 2011-10-01 2011-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not available...

47 CFR 80.290 - Auxiliary receiving antenna.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 5 2014-10-01 2014-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not available...

47 CFR 80.290 - Auxiliary receiving antenna.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 5 2012-10-01 2012-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not available...

47 CFR 80.290 - Auxiliary receiving antenna.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Auxiliary receiving antenna. 80.290 Section 80... antenna. An auxiliary receiving antenna must be provided when necessary to avoid unauthorized interruption or reduced efficiency of the required watch because the normal receiving antenna is not available...

40 CFR 1033.510 - Auxiliary power units.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If your...

40 CFR 1033.510 - Auxiliary power units.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If your...

40 CFR 1033.510 - Auxiliary power units.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If your...

40 CFR 1033.510 - Auxiliary power units.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If your...

40 CFR 1033.510 - Auxiliary power units.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Auxiliary power units. 1033.510 Section 1033.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM LOCOMOTIVES Test Procedures § 1033.510 Auxiliary power units. If your...

Effect of textile auxiliaries on the biodegradation of dyehouse effluent in activated sludge.

PubMed

Arslan Alaton, Idil; Insel, Güçlü; Eremektar, Gülen; Germirli Babuna, Fatos; Orhon, Derin

2006-03-01

The textile industry is confronted with serious environmental problems associated with its immense wastewater discharge, substantial pollution load, extremely high salinity, and alkaline, heavily coloured effluent. Particular sources of recalcitrance and toxicity in dyehouse effluent are two frequently used textile auxiliaries; i.e. dye carriers and biocidal finishing agents. The present experimental work reports the observation of scientific and practical significance related with the effect of two commercially important textile dye carriers and two biocidal finishing agents on biological activated sludge treatment at a textile preparation, dyeing and finishing plant in Istanbul. Respirometric measurements of the dyehouse effluent spiked with the selected textile chemicals were carried out for the assessment of the "readily biodegradable COD fraction" of the wastewater. The respirometric data obtained to visualize the effect of the selected textile auxiliaries on biomass activity was evaluated by an adopted activated sludge model. Results have indicated that the tested biocides did not exert any significant inhibitory effect on the treatment performance of the activated sludge reactor at the concentrations usually encountered in the final, total dyehouse effluent. The situation with the dye carriers was inherently different; one dye carrier appeared to be highly toxic and caused serious inhibition of the microbial respirometric activity, whereas the other dye carrier, also known as the more ecological alternative, i.e. the "Eco-Carrier", appeared to be biodegradable. Finally, the respirometric profile obtained for the Eco-Carrier was described by a simplified respirometric model.

Inflation and dark energy from f(R) gravity

NASA Astrophysics Data System (ADS)

Artymowski, Michał; Lalak, Zygmunt

2014-09-01

The standard Starobinsky inflation has been extended to the R + α Rn - β R2-n model to obtain a stable minimum of the Einstein frame scalar potential of the auxiliary field. As a result we have obtained obtain a scalar potential with non-zero value of residual vacuum energy, which may be a source of Dark Energy. Our results can be easily consistent with PLANCK or BICEP2 data for appropriate choices of the value of n.

Solar powered dispensary in Tibet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmed, S.F.; Rittelmann, P.R.; Kingman, K.

1995-11-01

A solar powered dispensary has been designed in Kastel, Tibet. This area is characterized by cold winters and clear skies. Solar energy systems are designed to provide space heating, water heating and electric power. since sources of auxiliary fuel are scarce, the building has been designed to provide heating by the sun only. Innovative use of daylighting is made to reduce the lighting electricity requirements. The design presented provides a good compromise between performance and the cost of the system.

Select geotechnical properties of a lime stabilized expansive soil amended with bagasse ash and coconut shell powder

NASA Astrophysics Data System (ADS)

James, Jijo; Pandian, P. Kasinatha

2018-03-01

Lime stabilization has been and still is one of the most preferred methods for stabilization of expansive soils. However, in the recent times, utilization of solid waste materials in soil stabilization has gained prominence as an effective means to manage wastes generated from various sources. In this work, an attempt has been made to utilize waste materials from two sources as auxiliary additives to lime in the stabilization of an expansive soil. Bagasse ash (BA), a waste by-product from the sugar industry and Coconut shell powder (CSP), a processed waste obtained from left over coconut shells of oil extraction industry were used as auxiliary additives. An expansive soil obtained from a local field was subjected to chemical, mineral, microstructural and geotechnical characterization in the laboratory and stabilized using 3% lime. The waste materials were subjected to chemical, mineral and microstructural characterization. The stabilization process was amended with four different contents viz. 0.25%, 0.5%, 1% and 2% of BA and CSP separately and the effect of the amendment was studied on the unconfined compressive strength (UCS), plasticity, swell-shrink and microstructural characteristics of the expansive soil. The results of the study indicated that BA amendment of lime stabilization performed better than CSP in improving the UCS, plasticity, swell-shrink and microstructure of the lime stabilized expansive soil.

47 CFR 74.831 - Scope of service and permissible transmissions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Power Auxiliary Stations § 74.831 Scope of service and permissible transmissions. The license for a low power auxiliary station authorizes the transmission of cues and orders to production personnel and... transmission of comments, interviews, and reports from the scene of a remote broadcast. Low power auxiliary...

47 CFR Alphabetical Index - Part 74

Code of Federal Regulations, 2010 CFR

2010-10-01

... Signal booster stations 74.985 Transmission standards 74.938 Wireless cable use 74.990 L Land mobile... Transmissions, Permissible (Low Power Auxiliaries) 74.831 Transmitter power (Remote Pickup) 74.461 Transmitters... 74.451 TV Auxiliaries 74.655 Lw Power Auxiliaries 74.851 ITFS 74.952 FM Translators/Boosters 74.1250...

29 CFR 779.208 - Auxiliary activities which are “related activities.”

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Auxiliary activities which are ârelated activities.â 779...; Enterprise Coverage Related Activities § 779.208 Auxiliary activities which are “related activities.” As... activities, such as central office and warehousing activities and bookkeeping, auditing, purchasing...

47 CFR 74.601 - Classes of TV broadcast auxiliary stations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... or other purposes as authorized in § 74.631. (d) TV translator relay station. A fixed station used... low power TV stations, unless specifically otherwise indicated. (f) TV microwave booster station. A... Television Broadcast Auxiliary Stations § 74.601 Classes of TV broadcast auxiliary stations. (a) TV pickup...

47 CFR 74.601 - Classes of TV broadcast auxiliary stations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... or other purposes as authorized in § 74.631. (d) TV translator relay station. A fixed station used... low power TV stations, unless specifically otherwise indicated. (f) TV microwave booster station. A... Television Broadcast Auxiliary Stations § 74.601 Classes of TV broadcast auxiliary stations. (a) TV pickup...

47 CFR 74.601 - Classes of TV broadcast auxiliary stations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... or other purposes as authorized in § 74.631. (d) TV translator relay station. A fixed station used... low power TV stations, unless specifically otherwise indicated. (f) TV microwave booster station. A... Television Broadcast Auxiliary Stations § 74.601 Classes of TV broadcast auxiliary stations. (a) TV pickup...

47 CFR 74.601 - Classes of TV broadcast auxiliary stations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... or other purposes as authorized in § 74.631. (d) TV translator relay station. A fixed station used... low power TV stations, unless specifically otherwise indicated. (f) TV microwave booster station. A... Television Broadcast Auxiliary Stations § 74.601 Classes of TV broadcast auxiliary stations. (a) TV pickup...

47 CFR 73.1670 - Auxiliary transmitters.

Code of Federal Regulations, 2010 CFR

2010-10-01

... broadcast station may, without further authority from the FCC, install and use with the main antenna system... or auxiliary antenna. (6) For testing, upon the request of representatives of the FCC. (b... auxiliary antenna must be obtained by filing an application for a construction permit on FCC form 301 (FCC...

30 CFR 18.22 - Boring-type machines equipped for auxiliary face ventilation.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Boring-type machines equipped for auxiliary... AND ACCESSORIES Construction and Design Requirements § 18.22 Boring-type machines equipped for auxiliary face ventilation. Each boring-type continuous-mining machine that is submitted for approval shall...

30 CFR 18.22 - Boring-type machines equipped for auxiliary face ventilation.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Boring-type machines equipped for auxiliary... AND ACCESSORIES Construction and Design Requirements § 18.22 Boring-type machines equipped for auxiliary face ventilation. Each boring-type continuous-mining machine that is submitted for approval shall...

30 CFR 18.22 - Boring-type machines equipped for auxiliary face ventilation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Boring-type machines equipped for auxiliary... AND ACCESSORIES Construction and Design Requirements § 18.22 Boring-type machines equipped for auxiliary face ventilation. Each boring-type continuous-mining machine that is submitted for approval shall...

30 CFR 18.22 - Boring-type machines equipped for auxiliary face ventilation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Boring-type machines equipped for auxiliary... AND ACCESSORIES Construction and Design Requirements § 18.22 Boring-type machines equipped for auxiliary face ventilation. Each boring-type continuous-mining machine that is submitted for approval shall...

30 CFR 18.22 - Boring-type machines equipped for auxiliary face ventilation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Boring-type machines equipped for auxiliary... AND ACCESSORIES Construction and Design Requirements § 18.22 Boring-type machines equipped for auxiliary face ventilation. Each boring-type continuous-mining machine that is submitted for approval shall...

49 CFR 229.125 - Headlights and auxiliary lights.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Headlights and auxiliary lights. 229.125 Section... Cab Equipment § 229.125 Headlights and auxiliary lights. (a) Each lead locomotive used in road service.... (c) Headlights shall be provided with a device to dim the light. (d) Effective December 31, 1997...

49 CFR 229.125 - Headlights and auxiliary lights.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Headlights and auxiliary lights. 229.125 Section... Cab Equipment § 229.125 Headlights and auxiliary lights. (a) Each lead locomotive used in road service.... (c) Headlights shall be provided with a device to dim the light. (d) Effective December 31, 1997...

49 CFR 229.125 - Headlights and auxiliary lights.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Headlights and auxiliary lights. 229.125 Section... Cab Equipment § 229.125 Headlights and auxiliary lights. (a) Each lead locomotive used in road service... light is aimed parallel to the tracks. If a locomotive or locomotive consist in road service is...

Ab Initio Density Fitting: Accuracy Assessment of Auxiliary Basis Sets from Cholesky Decompositions.

PubMed

Boström, Jonas; Aquilante, Francesco; Pedersen, Thomas Bondo; Lindh, Roland

2009-06-09

The accuracy of auxiliary basis sets derived by Cholesky decompositions of the electron repulsion integrals is assessed in a series of benchmarks on total ground state energies and dipole moments of a large test set of molecules. The test set includes molecules composed of atoms from the first three rows of the periodic table as well as transition metals. The accuracy of the auxiliary basis sets are tested for the 6-31G**, correlation consistent, and atomic natural orbital basis sets at the Hartree-Fock, density functional theory, and second-order Møller-Plesset levels of theory. By decreasing the decomposition threshold, a hierarchy of auxiliary basis sets is obtained with accuracies ranging from that of standard auxiliary basis sets to that of conventional integral treatments.

Improve the Efficiency of the Service Process as a Result of the Muda Ideology

NASA Astrophysics Data System (ADS)

Lorenc, Augustyn; Przyłuski, Krzysztof

2018-06-01

The aim of the paper was to improve service processes carried out by Knorr-Bremse Systemy Kolejowe Polska sp. z o.o. Particularly, emphasise unnecessary movements and physical efforts of employees. The indirect goal was to find a solution in the simplest possible way using the Muda ideology. In order to improve the service process at the beginning was executed the process mapping for the devices to be repaired, ie. brake callipers, electro-hydraulic units and auxiliary release units. The processes were assessed and shown as Pareto-Lorenz analysis. In order to determine the most time consuming process. Based on the obtained results use of a column crane with articulated arm was proposed to facilitate the transfer of heavy components between areas. The final step was to assess the effectiveness of the proposed solution in terms of time saving. From the company perspective results of the analysis are important. The proposed solution not only reduces total service time but also contributes to crew's work comfort.

Nonlocal Symmetries and Interaction Solutions for Potential Kadomtsev-Petviashvili Equation

NASA Astrophysics Data System (ADS)

Ren, Bo; Yu, Jun; Liu, Xi-Zhong

2016-03-01

The nonlocal symmetry for the potential Kadomtsev-Petviashvili (pKP) equation is derived by the truncated Painlevé analysis. The nonlocal symmetry is localized to the Lie point symmetry by introducing the auxiliary dependent variable. Thanks to localization process, the finite symmetry transformations related with the nonlocal symmetry are obtained by solving the prolonged systems. The inelastic interactions among the multiple-front waves of the pKP equation are generated from the finite symmetry transformations. Based on the consistent tanh expansion method, a nonauto-Bäcklund transformation (BT) theorem of the pKP equation is constructed. We can get many new types of interaction solutions because of the existence of an arbitrary function in the nonauto-BT theorem. Some special interaction solutions are investigated both in analytical and graphical ways. Supported by the National Natural Science Foundation of China under Grant Nos. 11305106, 11275129 and 11405110, the Natural Science Foundation of Zhejiang Province of China under Grant No. LQ13A050001

IN-PILE CORROSION TEST LOOPS FOR AQUEOUS HOMOGENEOUS REACTOR SOLUTIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Savage, H.C.; Jenks, G.H.; Bohlmann, E.G.

1960-12-21

An in-pile corrosion test loop is described which is used to study the effect of reactor radiation on the corrosion of materials of construction and the chemical stability of fuel solutions of interest to the Aqueous Homogeneous Reactor Program at ORNL. Aqueous solutions of uranyl sulfate are circulated in the loop by means of a 5-gpm canned-rotor pump, and the pump loop is designed for operation at temperatures to 300 ts C and pressures to 2000 psia while exposed to reactor radiation in beam-hole facilities of the LITR and ORR. Operation of the first loop in-pile was begun in Octobermore » 1954, and since that time 17 other in-pile loop experiments were completed. Design criteria of the pump loop and its associated auxiliary equipment and instrumentation are described. In-pile operating procedures, safety features, and operating experience are presented. A cost summary of the design, fabrication, and installation of the loop and experimental facillties is also included. (auth)« less

Numerical aerodynamic simulation facility. [for flows about three-dimensional configurations

NASA Technical Reports Server (NTRS)

Bailey, F. R.; Hathaway, A. W.

1978-01-01

Critical to the advancement of computational aerodynamics capability is the ability to simulate flows about three-dimensional configurations that contain both compressible and viscous effects, including turbulence and flow separation at high Reynolds numbers. Analyses were conducted of two solution techniques for solving the Reynolds averaged Navier-Stokes equations describing the mean motion of a turbulent flow with certain terms involving the transport of turbulent momentum and energy modeled by auxiliary equations. The first solution technique is an implicit approximate factorization finite-difference scheme applied to three-dimensional flows that avoids the restrictive stability conditions when small grid spacing is used. The approximate factorization reduces the solution process to a sequence of three one-dimensional problems with easily inverted matrices. The second technique is a hybrid explicit/implicit finite-difference scheme which is also factored and applied to three-dimensional flows. Both methods are applicable to problems with highly distorted grids and a variety of boundary conditions and turbulence models.

Polynomial algorithms for the Maximal Pairing Problem: efficient phylogenetic targeting on arbitrary trees

PubMed Central

2010-01-01

Background The Maximal Pairing Problem (MPP) is the prototype of a class of combinatorial optimization problems that are of considerable interest in bioinformatics: Given an arbitrary phylogenetic tree T and weights ωxy for the paths between any two pairs of leaves (x, y), what is the collection of edge-disjoint paths between pairs of leaves that maximizes the total weight? Special cases of the MPP for binary trees and equal weights have been described previously; algorithms to solve the general MPP are still missing, however. Results We describe a relatively simple dynamic programming algorithm for the special case of binary trees. We then show that the general case of multifurcating trees can be treated by interleaving solutions to certain auxiliary Maximum Weighted Matching problems with an extension of this dynamic programming approach, resulting in an overall polynomial-time solution of complexity (n4 log n) w.r.t. the number n of leaves. The source code of a C implementation can be obtained under the GNU Public License from http://www.bioinf.uni-leipzig.de/Software/Targeting. For binary trees, we furthermore discuss several constrained variants of the MPP as well as a partition function approach to the probabilistic version of the MPP. Conclusions The algorithms introduced here make it possible to solve the MPP also for large trees with high-degree vertices. This has practical relevance in the field of comparative phylogenetics and, for example, in the context of phylogenetic targeting, i.e., data collection with resource limitations. PMID:20525185

Computational design and engineering of polymeric orthodontic aligners.

PubMed

Barone, S; Paoli, A; Razionale, A V; Savignano, R

2016-10-05

Transparent and removable aligners represent an effective solution to correct various orthodontic malocclusions through minimally invasive procedures. An aligner-based treatment requires patients to sequentially wear dentition-mating shells obtained by thermoforming polymeric disks on reference dental models. An aligner is shaped introducing a geometrical mismatch with respect to the actual tooth positions to induce a loading system, which moves the target teeth toward the correct positions. The common practice is based on selecting the aligner features (material, thickness, and auxiliary elements) by only considering clinician's subjective assessments. In this article, a computational design and engineering methodology has been developed to reconstruct anatomical tissues, to model parametric aligner shapes, to simulate orthodontic movements, and to enhance the aligner design. The proposed approach integrates computer-aided technologies, from tomographic imaging to optical scanning, from parametric modeling to finite element analyses, within a 3-dimensional digital framework. The anatomical modeling provides anatomies, including teeth (roots and crowns), jaw bones, and periodontal ligaments, which are the references for the down streaming parametric aligner shaping. The biomechanical interactions between anatomical models and aligner geometries are virtually reproduced using a finite element analysis software. The methodology allows numerical simulations of patient-specific conditions and the comparative analyses of different aligner configurations. In this article, the digital framework has been used to study the influence of various auxiliary elements on the loading system delivered to a maxillary and a mandibular central incisor during an orthodontic tipping movement. Numerical simulations have shown a high dependency of the orthodontic tooth movement on the auxiliary element configuration, which should then be accurately selected to maximize the aligner's effectiveness. Copyright © 2016 John Wiley & Sons, Ltd.

Reduced-cost linear-response CC2 method based on natural orbitals and natural auxiliary functions

PubMed Central

Mester, Dávid

2017-01-01

A reduced-cost density fitting (DF) linear-response second-order coupled-cluster (CC2) method has been developed for the evaluation of excitation energies. The method is based on the simultaneous truncation of the molecular orbital (MO) basis and the auxiliary basis set used for the DF approximation. For the reduction of the size of the MO basis, state-specific natural orbitals (NOs) are constructed for each excited state using the average of the second-order Møller–Plesset (MP2) and the corresponding configuration interaction singles with perturbative doubles [CIS(D)] density matrices. After removing the NOs of low occupation number, natural auxiliary functions (NAFs) are constructed [M. Kállay, J. Chem. Phys. 141, 244113 (2014)], and the NAF basis is also truncated. Our results show that, for a triple-zeta basis set, about 60% of the virtual MOs can be dropped, while the size of the fitting basis can be reduced by a factor of five. This results in a dramatic reduction of the computational costs of the solution of the CC2 equations, which are in our approach about as expensive as the evaluation of the MP2 and CIS(D) density matrices. All in all, an average speedup of more than an order of magnitude can be achieved at the expense of a mean absolute error of 0.02 eV in the calculated excitation energies compared to the canonical CC2 results. Our benchmark calculations demonstrate that the new approach enables the efficient computation of CC2 excitation energies for excited states of all types of medium-sized molecules composed of up to 100 atoms with triple-zeta quality basis sets. PMID:28527453

Model predictive control-based dynamic coordinate strategy for hydraulic hub-motor auxiliary system of a heavy commercial vehicle

NASA Astrophysics Data System (ADS)

Zeng, Xiaohua; Li, Guanghan; Yin, Guodong; Song, Dafeng; Li, Sheng; Yang, Nannan

2018-02-01

Equipping a hydraulic hub-motor auxiliary system (HHMAS), which mainly consists of a hydraulic variable pump, a hydraulic hub-motor, a hydraulic valve block and hydraulic accumulators, with part-time all-wheel-drive functions improves the power performance and fuel economy of heavy commercial vehicles. The coordinated control problem that occurs when HHMAS operates in the auxiliary drive mode is addressed in this paper; the solution to this problem is the key to the maximization of HHMAS. To achieve a reasonable distribution of the engine power between mechanical and hydraulic paths, a nonlinear control scheme based on model predictive control (MPC) is investigated. First, a nonlinear model of HHMAS with vehicle dynamics and tire slip characteristics is built, and a controller-design-oriented model is simplified. Then, a steady-state feedforward + dynamic MPC feedback controller (FMPC) is designed to calculate the control input sequence of engine torque and hydraulic variable pump displacement. Finally, the controller is tested in the MATLAB/Simulink and AMESim co-simulation platform and the hardware-in-the-loop experiment platform, and its performance is compared with that of the existing proportional-integral-derivative controller and the feedforward controller under the same conditions. Simulation results show that the designed FMPC has the best performance, and control performance can be guaranteed in a real-time environment. Compared with the tracking control error of the feedforward controller, that of the designed FMPC is decreased by 85% and the traction efficiency performance is improved by 23% under a low-friction-surface condition. Moreover, under common road conditions for heavy commercial vehicles, the traction force can increase up to 13.4-15.6%.

Symmetry breaking in occupation number based slave-particle methods

NASA Astrophysics Data System (ADS)

Georgescu, Alexandru B.; Ismail-Beigi, Sohrab

2017-10-01

We describe a theoretical approach to finding spontaneously symmetry-broken electronic phases due to strong electronic interactions when using recently developed slave-particle (slave-boson) approaches based on occupation numbers. We describe why, to date, spontaneous symmetry breaking has proven difficult to achieve in such approaches. We then provide a total energy based approach for introducing auxiliary symmetry-breaking fields into the solution of the slave-particle problem that leads to lowered total energies for symmetry-broken phases. We point out that not all slave-particle approaches yield energy lowering: the slave-particle model being used must explicitly describe the degrees of freedom that break symmetry. Finally, our total energy approach permits us to greatly simplify the formalism used to achieve a self-consistent solution between spinon and slave modes while increasing the numerical stability and greatly speeding up the calculations.

Optimization Under Uncertainty for Electronics Cooling Design

NASA Astrophysics Data System (ADS)

Bodla, Karthik K.; Murthy, Jayathi Y.; Garimella, Suresh V.

Optimization under uncertainty is a powerful methodology used in design and optimization to produce robust, reliable designs. Such an optimization methodology, employed when the input quantities of interest are uncertain, produces output uncertainties, helping the designer choose input parameters that would result in satisfactory thermal solutions. Apart from providing basic statistical information such as mean and standard deviation in the output quantities, auxiliary data from an uncertainty based optimization, such as local and global sensitivities, help the designer decide the input parameter(s) to which the output quantity of interest is most sensitive. This helps the design of experiments based on the most sensitive input parameter(s). A further crucial output of such a methodology is the solution to the inverse problem - finding the allowable uncertainty range in the input parameter(s), given an acceptable uncertainty range in the output quantity of interest...

Entanglement from dissipation and holographic interpretation

NASA Astrophysics Data System (ADS)

Cantcheff, M. Botta; Gadelha, Alexandre L.; Marchioro, Dáfni F. Z.; Nedel, Daniel Luiz

2018-02-01

In this work we study a dissipative field theory where the dissipation process is manifestly related to dynamical entanglement and put it in the holographic context. Such endeavour is realized by further development of a canonical approach to study quantum dissipation, which consists of doubling the degrees of freedom of the original system by defining an auxiliary one. A time dependent entanglement entropy for the vacumm state is calculated and a geometrical interpretation of the auxiliary system and the entropy is given in the context of the AdS/CFT correspondence using the Ryu-Takayanagi formula. We show that the dissipative dynamics is controlled by the entanglement entropy and there are two distinct stages: in the early times the holographic interpretation requires some deviation from classical General Relativity; in the later times the quantum system is described as a wormhole, a solution of the Einstein's equations near to a maximally extended black hole with two asymptotically AdS boundaries. We focus our holographic analysis in this regime, and suggest a mechanism similar to teleportation protocol to exchange (quantum) information between the two CFTs on the boundaries (see Maldacena et al. in Fortschr Phys 65(5):1700034, arXiv:1704.05333 [hep-th], 2017).

Design and development of solar power-assisted manual/electric wheelchair.

PubMed

Chien, Chi-Sheng; Huang, Tung-Yung; Liao, Tze-Yuan; Kuo, Tsung-Yuan; Lee, Tzer-Min

2014-01-01

Wheelchairs are an essential assistive device for many individuals with injury or disability. Manual wheelchairs provide a relatively low-cost solution to the mobility needs of such individuals. Furthermore, they provide an effective means of improving the user's cardiopulmonary function and upper-limb muscle strength. However, manual wheelchairs have a loss gross mechanical efficiency, and thus the risk of user fatigue and upper-limb injury is increased. Electric-powered wheelchairs reduce the risk of injury and provide a more convenient means of transportation. However, they have a large physical size and are relatively expensive. Accordingly, the present study utilizes a quality function deployment method to develop a wheelchair with a user-selectable manual/electric propulsion mode and an auxiliary solar power supply system. The auxiliary solar power supply increased the travel range of the wheelchair by approximately 26% compared with that of a wheelchair powered by battery alone. Moreover, the wheelchair has a modular design and can be disassembled and folded for ease of transportation or storage. Overall, the present results suggest that the proposed wheelchair provides an effective and convenient means of meeting the mobility needs of individuals with mobility difficulties.

Optical Features of Efficient Europium(III) Complexes with β-Diketonato and Auxiliary Ligands and Mechanistic Investigation of Energy Transfer Process.

PubMed

Bala, Manju; Kumar, Satish; Taxak, V B; Boora, Priti; Khatkar, S P

2016-09-01

Two new europium (III) complexes have been synthesized with 1,3-[bis(4-methoxyphenyl)]propane-1,3-dionato (HBMPD) as main ligand and 2,2'-bipyridyl (bipy) or 1,10-phenanthroline (phen) as an auxiliary ligand. The main ligand HBMPD has been synthesized by ecofriendly microwave approach and complexes by solution precipitation method. The resulting materials are characterized by IR, (1)H-NMR, elemental analysis, X-ray diffraction, UV-visible and TG-DTG techniques. The photoluminescence (PL) spectroscopy depicts the detail analysis of photophysical properties of the complexes, their results show that the ligand interact with Eu (III) ion which act as antenna and transfers the absorbed energy to the central europium(III) ion via sensitization process efficiently. As a consequence of this interaction, these materials exhibit excellent luminescent intensity, long decay time (τ), high quantum efficiency (η) and Judd-Ofelt intensity parameter (Ω2). The CIE coordinates fall under the deep red region, matching well with the NTSC (National Television Standard Committee) standard. Hence, these highly efficient optical materials can be used as a red component in organic light emitting diodes (OLEDs) and full color flat panel displays.

Reconstruction from scalar-tensor theory and the inhomogeneous equation of state in f( T) gravity

NASA Astrophysics Data System (ADS)

Said, Jackson Levi

2017-12-01

General relativity (GR) characterizes gravity as a geometric properly exhibited as curvature on spacetime. Teleparallelism describes gravity through torsional properties, and can reproduce GR at the level of equations. Similar to f( R) gravity, on taking a generalization, f( T) gravity can produce various modifications its gravitational mechanism. The resulting field equations are inherently distinct to f( R) gravity in that they are second order. In the present work, f( T) gravity is examined in the cosmological context with a number of solutions reconstructed by means of an auxiliary scalar field. To do this, various forms of the Hubble parameter are considered with an f( T) Lagrangian emerging for each instance. In addition, the inhomogeneous equation of state (EoS) is investigated with a particular Hubble parameter model used to show how this can be used to reconstruct the f( T) Lagrangian. Observationally, the auxiliary scalar field and the exotic terms in the FRW field equations give the same results, meaning that the variation in the Hubble parameter may be interpreted as the need to reformulate gravity in some way, as in f( T) gravity.

Modeling activity recognition of multi resident using label combination of multi label classification in smart home

NASA Astrophysics Data System (ADS)

Mohamed, Raihani; Perumal, Thinagaran; Sulaiman, Md Nasir; Mustapha, Norwati; Zainudin, M. N. Shah

2017-10-01

Pertaining to the human centric concern and non-obtrusive way, the ambient sensor type technology has been selected, accepted and embedded in the environment in resilient style. Human activities, everyday are gradually becoming complex and thus complicate the inferences of activities when it involving the multi resident in the same smart environment. Current works solutions focus on separate model between the resident, activities and interactions. Some study use data association and extra auxiliary of graphical nodes to model human tracking information in an environment and some produce separate framework to incorporate the auxiliary for interaction feature model. Thus, recognizing the activities and which resident perform the activity at the same time in the smart home are vital for the smart home development and future applications. This paper will cater the above issue by considering the simplification and efficient method using the multi label classification framework. This effort eliminates time consuming and simplifies a lot of pre-processing tasks comparing with previous approach. Applications to the multi resident multi label learning in smart home problems shows the LC (Label Combination) using Decision Tree (DT) as base classifier can tackle the above problems.

Advanced Reactor PSA Methodologies for System Reliability Analysis and Source Term Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grabaskas, D.; Brunett, A.; Passerini, S.

Beginning in 2015, a project was initiated to update and modernize the probabilistic safety assessment (PSA) of the GE-Hitachi PRISM sodium fast reactor. This project is a collaboration between GE-Hitachi and Argonne National Laboratory (Argonne), and funded in part by the U.S. Department of Energy. Specifically, the role of Argonne is to assess the reliability of passive safety systems, complete a mechanistic source term calculation, and provide component reliability estimates. The assessment of passive system reliability focused on the performance of the Reactor Vessel Auxiliary Cooling System (RVACS) and the inherent reactivity feedback mechanisms of the metal fuel core. Themore » mechanistic source term assessment attempted to provide a sequence specific source term evaluation to quantify offsite consequences. Lastly, the reliability assessment focused on components specific to the sodium fast reactor, including electromagnetic pumps, intermediate heat exchangers, the steam generator, and sodium valves and piping.« less

Preliminary design study of an alternate heat source assembly for a Brayton isotope power system

NASA Technical Reports Server (NTRS)

Strumpf, H. J.

1978-01-01

Results are presented for a study of the preliminary design of an alternate heat source assembly (HSA) intended for use in the Brayton isotope power system (BIPS). The BIPS converts thermal energy emitted by a radioactive heat source into electrical energy by means of a closed Brayton cycle. A heat source heat exchanger configuration was selected and optimized. The design consists of a 10 turn helically wound Hastelloy X tube. Thermal analyses were performed for various operating conditions to ensure that post impact containment shell (PICS) temperatures remain within specified limits. These limits are essentially satisfied for all modes of operation except for the emergency cooling system for which the PICS temperatures are too high. Neon was found to be the best choice for a fill gas for auxiliary cooling system operation. Low cycle fatigue life, natural frequency, and dynamic loading requirements can be met with minor modifications to the existing HSA.

49 CFR 229.133 - Interim locomotive conspicuity measures-auxiliary external lights.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., whichever comes first. (3) Any lead locomotive equipped with two white auxiliary lights spaced at least 44... external lights. 229.133 Section 229.133 Transportation Other Regulations Relating to Transportation...—auxiliary external lights. (a) A locomotive at the head of a train or other movement is authorized to be...

49 CFR 229.133 - Interim locomotive conspicuity measures-auxiliary external lights.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., whichever comes first. (3) Any lead locomotive equipped with two white auxiliary lights spaced at least 44... external lights. 229.133 Section 229.133 Transportation Other Regulations Relating to Transportation...—auxiliary external lights. (a) A locomotive at the head of a train or other movement is authorized to be...

47 CFR 74.690 - Transition of the 1990-2025 MHz band from the Broadcast Auxiliary Service to emerging technologies.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Broadcast Auxiliary Service to emerging technologies. 74.690 Section 74.690 Telecommunication FEDERAL... of the 1990-2025 MHz band from the Broadcast Auxiliary Service to emerging technologies. (a) New Entrants are collectively defined as those licensees proposing to use emerging technologies to implement...

30 CFR 57.22208 - Auxiliary fans (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... NONMETAL MINES Safety Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22208 Auxiliary... which have been so designed that methane cannot enter the airway, shall be approved by MSHA under the...) Tests for methane shall be made at auxiliary fans before they are started. ...

30 CFR 57.22209 - Auxiliary fans (I-C mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22209 Auxiliary fans (I-C mines.... Tests for methane shall be made at electric auxiliary fans before they are started. Such fans shall not be operated when air passing over or through them contains 0.5 percent or more methane. ...

46 CFR 52.01-35 - Auxiliary, donkey, fired thermal fluid heater, and heating boilers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Auxiliary, donkey, fired thermal fluid heater, and heating boilers. 52.01-35 Section 52.01-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-35 Auxiliary, donkey, fired thermal...

46 CFR 52.01-35 - Auxiliary, donkey, fired thermal fluid heater, and heating boilers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Auxiliary, donkey, fired thermal fluid heater, and heating boilers. 52.01-35 Section 52.01-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-35 Auxiliary, donkey, fired thermal...

46 CFR 52.01-35 - Auxiliary, donkey, fired thermal fluid heater, and heating boilers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Auxiliary, donkey, fired thermal fluid heater, and heating boilers. 52.01-35 Section 52.01-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-35 Auxiliary, donkey, fired thermal...

46 CFR 52.01-35 - Auxiliary, donkey, fired thermal fluid heater, and heating boilers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Auxiliary, donkey, fired thermal fluid heater, and heating boilers. 52.01-35 Section 52.01-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-35 Auxiliary, donkey, fired thermal...

78 FR 16198 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-14

... determine if wires touch the upper surface of the center upper auxiliary fuel tank, and marking the location, as necessary; inspecting all wire bundles above the center upper auxiliary fuel tank for splices and... requires inspecting to determine if wires touch the upper surface of the center upper auxiliary fuel tank...

46 CFR 11.401 - Ocean and near-coastal officer or STCW endorsements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... be endorsed for sail or auxiliary sail as appropriate. The applicant must present the equivalent... vessels of not more than 1,600 gross tons endorsed for auxiliary sail, the applicant must meet the total... tonnage experience, including at least one year of deck service on appropriately sized auxiliary-sail...

46 CFR 11.401 - Ocean and near-coastal officer or STCW endorsements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... be endorsed for sail or auxiliary sail as appropriate. The applicant must present the equivalent... vessels of not more than 1,600 gross tons endorsed for auxiliary sail, the applicant must meet the total... tonnage experience, including at least one year of deck service on appropriately sized auxiliary-sail...

Emergent Uses of BE and DO: Evidence from Children with Specific Language Impairment.

ERIC Educational Resources Information Center

Hadley, Pamela A.; Rice, Mabel L.

1996-01-01

Examines the use of finiteness markers copula "BE" and auxiliaries "BE" and "DO" in the spontaneous speech of children with specific language impairment. Focus is on whether the categorical distinctions between main verbs and auxiliaries and/or between the auxiliary types influence the relative order of emergence…

30 CFR 57.22209 - Auxiliary fans (I-C mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22209 Auxiliary fans (I-C mines.... Tests for methane shall be made at electric auxiliary fans before they are started. Such fans shall not be operated when air passing over or through them contains 0.5 percent or more methane. ...

Backscattering and absorption coefficients for electrons: Solutions of invariant embedding transport equations using a method of convergence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Figueroa, C.; Brizuela, H.; Heluani, S. P.

2014-05-21

The backscattering coefficient is a magnitude whose measurement is fundamental for the characterization of materials with techniques that make use of particle beams and particularly when performing microanalysis. In this work, we report the results of an analytic method to calculate the backscattering and absorption coefficients of electrons in similar conditions to those of electron probe microanalysis. Starting on a five level states ladder model in 3D, we deduced a set of integro-differential coupled equations of the coefficients with a method know as invariant embedding. By means of a procedure proposed by authors, called method of convergence, two types ofmore » approximate solutions for the set of equations, namely complete and simple solutions, can be obtained. Although the simple solutions were initially proposed as auxiliary forms to solve higher rank equations, they turned out to be also useful for the estimation of the aforementioned coefficients. In previous reports, we have presented results obtained with the complete solutions. In this paper, we present results obtained with the simple solutions of the coefficients, which exhibit a good degree of fit with the experimental data. Both the model and the calculation method presented here can be generalized to other techniques that make use of different sorts of particle beams.« less

Thermionic converter

DOEpatents

Rasor, Ned S.; Britt, Edward J.

1976-01-01

A gas-filled thermionic converter is provided with a collector and an emitter having a main emitter region and an auxiliary emitter region in electrical contact with the main emitter region. The main emitter region is so positioned with respect to the collector that a main gap is formed therebetween and the auxiliary emitter region is so positioned with respect to the collector that an auxiliary gap is formed therebetween partially separated from the main gap with access allowed between the gaps to allow ionizable gas in each gap to migrate therebetween. With heat applied to the emitter the work function of the auxiliary emitter region is sufficiently greater than the work function of the collector so that an ignited discharge occurs in the auxiliary gap and the work function of the main emitter region is so related to the work function of the collector that an unignited discharge occurs in the main gap sustained by the ions generated in the auxiliary gap. A current flows through a load coupled across the emitter and collector due to the unignited discharge in the main gap.

Simplified technique for auxiliary orthotopic liver transplantation using a whole graft

PubMed Central

ROCHA-SANTOS, Vinicius; NACIF, Lucas Souto; PINHEIRO, Rafael Soares; DUCATTI, Liliana; ANDRAUS, Wellington; D'ALBURQUERQUE, Luiz Carneiro

2015-01-01

Background Acute liver failure is associated with a high mortality rate and the main purposes of treatment are to prevent cerebral edema and infections, which often are responsible for patient death. The orthotopic liver transplantation is the gold standard treatment and improves the 1-year survival. Aim To describe an alternative technique to auxiliary liver transplant on acute liver failure. Method Was performed whole auxiliary liver transplantation as an alternative technique for a partial auxiliary liver transplantation using a whole liver graft from a child removing the native right liver performed a right hepatectomy. The patient met the O´Grady´s criteria and the rational to indicate an auxiliary orthotopic liver transplantation was the acute classification without hemodynamic instability or renal failure in a patient with deterioration in consciousness. Results The procedure improved liver function and decreased intracranial hypertension in the postoperative period. Conclusion This technique can overcome some postoperative complications that are associated with partial grafts. As far as is known, this is the first case of auxiliary orthotopic liver transplantation in Brazil. PMID:26176253

Calculation of compressible flow about three-dimensional inlets with auxiliary inlets, slats and vanes by means of a panel method

NASA Technical Reports Server (NTRS)

Hess, J. L.; Friedman, D. M.; Clark, R. W.

1985-01-01

An efficient and user oriented method was constructed for calculating flow in and about complex inlet configurations. Efficiency is attained by: (1) the use of a panel method; (2) a technique of superposition for obtaining solutions at any inlet operating condition; and (3) employment of an advanced matrix iteration technique for solving large full systems of equations, including the nonlinear equations for the Kutta condition. User concerns are addressed by the provision of several novel graphical output options that yield a more complete comprehension of the flowfield than was possible previously.

Electric auxiliary power unit for Shuttle evolution

NASA Technical Reports Server (NTRS)

Meyer, Doug; Weber, Kent; Scott, Walter

1989-01-01

The Space Shuttle Orbiter currently uses three hydrazine fueled auxiliary power units (APUs) to provide hydraulic power for the vehicle aerodynamic surface controls, main engine thrust vector control, landing gear, steering, and brakes. Electric auxiliary power units have been proposed as possible replacements to the hydrazine auxiliary power units. Along with the potential advantages, this paper describes an Electric APU configuration and addresses the technical issues and risks associated with the subsystem components. Additionally, characteristics of an Electric APU compared to the existing APU and the direction of future study with respect to the Electric APU is suggested.

Data embedding

DOEpatents

Sandford, II, Maxwell T.; Handel, Theodore G.

1997-01-01

A method of embedding auxiliary information into a set of host data, such as a photograph, television signal, facsimile transmission, or identification card. All such host data contain intrinsic noise, allowing pixels in the host data which are nearly identical and which have values differing by less than the noise value to be manipulated and replaced with auxiliary data. As the embedding method does not change the elemental values of the host data, the auxiliary data do not noticeably affect the appearance or interpretation of the host data. By a substantially reverse process, the embedded auxiliary data can be retrieved easily by an authorized user.

Data embedding

DOEpatents

Sandford, M.T. II; Handel, T.G.

1997-08-19

A method is disclosed for embedding auxiliary information into a set of host data, such as a photograph, television signal, facsimile transmission, or identification card. All such host data contain intrinsic noise, allowing pixels in the host data which are nearly identical and which have values differing by less than the noise value to be manipulated and replaced with auxiliary data. As the embedding method does not change the elemental values of the host data, the auxiliary data do not noticeably affect the appearance or interpretation of the host data. By a substantially reverse process, the embedded auxiliary data can be retrieved easily by an authorized user. 19 figs.

Method to calibrate phase fluctuation in polarization-sensitive swept-source optical coherence tomography

NASA Astrophysics Data System (ADS)

Lu, Zenghai; Kasaragod, Deepa K.; Matcher, Stephen J.

2011-07-01

We present a phase fluctuation calibration method for polarization-sensitive swept-source optical coherence tomography (PS-SS-OCT) using continuous polarization modulation. The method uses a low-voltage broadband polarization modulator driven by a synchronized sinusoidal burst waveform rather than an asynchronous waveform, together with the removal of the global phases of the measured Jones matrices by the use of matrix normalization. This makes it possible to average the measured Jones matrices to remove the artifact due to the speckle noise of the signal in the sample without introducing auxiliary optical components into the sample arm. This method was validated on measurements of an equine tendon sample by the PS-SS-OCT system.

Source process and tectonic implication of the January 20, 2007 Odaesan earthquake, South Korea

NASA Astrophysics Data System (ADS)

Abdel-Fattah, Ali K.; Kim, K. Y.; Fnais, M. S.; Al-Amri, A. M.

2014-04-01

The source process for the 20th of January 2007, Mw 4.5 Odaesan earthquake in South Korea is investigated in the low- and high-frequency bands, using velocity and acceleration waveform data recorded by the Korea Meteorological Administration Seismographic Network at distances less than 70 km from the epicenter. Synthetic Green functions are adopted for the low-frequency band of 0.1-0.3 Hz by using the wave-number integration technique and the one dimensional velocity model beneath the epicentral area. An iterative technique was performed by a grid search across the strike, dip, rake, and focal depth of rupture nucleation parameters to find the best-fit double-couple mechanism. To resolve the nodal plane ambiguity, the spatiotemporal slip distribution on the fault surface was recovered using a non-negative least-square algorithm for each set of the grid-searched parameters. The focal depth of 10 km was determined through the grid search for depths in the range of 6-14 km. The best-fit double-couple mechanism obtained from the finite-source model indicates a vertical strike-slip faulting mechanism. The NW faulting plane gives comparatively smaller root-mean-squares (RMS) error than its auxiliary plane. Slip pattern event provides simple source process due to the effect of Low-frequency that acted as a point source model. Three empirical Green functions are adopted to investigate the source process in the high-frequency band. A set of slip models was recovered on both nodal planes of the focal mechanism with various rupture velocities in the range of 2.0-4.0 km/s. Although there is a small difference between the RMS errors produced by the two orthogonal nodal planes, the SW dipping plane gives a smaller RMS error than its auxiliary plane. The slip distribution is relatively assessable by the oblique pattern recovered around the hypocenter in the high-frequency analysis; indicating a complex rupture scenario for such moderate-sized earthquake, similar to those reported for large earthquakes.

The Influence of Discourse Context on Children's Provision of Auxiliary BE

ERIC Educational Resources Information Center

Theakston, Anna L.; Lieven, Elena V. M.

2008-01-01

LChildren pass through a stage in development when they produce utterances that contain auxiliary BE ("he's playing") and utterances where auxiliary BE is omitted ("he playing"). One explanation that has been put forward to explain this phenomenon is the presence of questions in the input that model S-V word order (Theakston, Lieven & Tomasello,…

Modal Auxiliaries and Their Semantic Functions Used by Advanced EFL Learners

ERIC Educational Resources Information Center

Torabiardakani, Najmeh; Khojasteh, Laleh; Shokrpour, Nasrin

2015-01-01

Since modal auxiliary verbs have been proved to be one of the most troublesome grammatical structures in English, the researchers of this study decided to do an analysis on the ways in which advanced EFL Iranian students use modal auxiliaries focusing specially on nine modals' semantic functions. Consequently, was conducted based on the following…

The Range of Gapping and the Status of Auxiliaries.

ERIC Educational Resources Information Center

Warner, A. R.

Full verbs and auxiliaries are subject to gapping. In the simplest cases, this construction type involves apparent ellipsis within one or more clausal conjuncts under identity with the finite verb or auxiliary of a preceding conjunct. It has often been suggested that the apparent ellipsis must involve at least a verb. Some researchers see in the…

49 CFR 39.51 - What is the general requirement for PVOs' provision of auxiliary aids and services to passengers?

Code of Federal Regulations, 2010 CFR

2010-10-01

... Secretary of Transportation TRANSPORTATION FOR INDIVIDUALS WITH DISABILITIES: PASSENGER VESSELS Information... type of auxiliary aid or service is necessary, you must give primary consideration to the requests of... disabilities. (c) If a provision of a particular auxiliary aid or service would result in a fundamental...

Auxiliary coil controls temperature of RF induction heater

NASA Technical Reports Server (NTRS)

1966-01-01

Auxiliary coil controls the temperature of an RF induction furnace that is powered by a relatively unstable RF generator. Manual or servoed adjustments of the relative position of the auxiliary coil, which is placed in close proximity to the RF coil, changes the looseness of the RF coil and hence the corresponding heating effect of its RF field.

75 FR 3639 - Revisions to Rules Authorizing the Operation of Low Power Auxiliary Stations in the 698-806 MHz...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-22

... 698-806 MHz Band; Public Interest Spectrum Coalition, Petition for Rulemaking Regarding Low Power... Power Auxiliary Stations in the 698-806 MHz Band; Public Interest Spectrum Coalition, Petition for... Operation of Low Power Auxiliary Stations in the 698-806 MHz Band; Public Interest Spectrum Coalition...

Applicability of PSD to Pennsylvania Power and Light Auxiliary Boiler

EPA Pesticide Factsheets

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Electrical Performance of Monolayer MoS2 Field-Effect Transistors Prepared by Chemical Vapor Deposition

DTIC Science & Technology

2013-05-16

Furthermore, MoS2 also shows promise for use in logic circuits and optoelectronic devices, and it is a promising material for use on flexible and...onto an auxiliary silicon substrate and placed inside a tube furnace with the growth substrates surrounding it. Sulfur powder, placed upstream near the...opening of the furnace at an approximate temperature of 600 C, was subli- mated for use as the sulfur vapor source. The furnace was heated to a peak

Low-speed performance of an axisymmetric, mixed-compression, supersonic inlet with auxiliary inlets

NASA Technical Reports Server (NTRS)

Trefny, C. J.; Wasserbauer, J. W.

1986-01-01

A test program was conducted to determine the aerodynamic performance and acoustic characteristics associated with the low-speed operation of a supersonic, axisymmetric, mixed-compression inlet with auxiliary inlets. Blow-in-auxiliary doors were installed on the NASA Ames P inlet. One door per quadrant was located on the cowl in the subsonic diffuser selection of the inlet. Auxiliary inlets with areas of 20 and 40 percent of the inlet capture area were tested statically and at free-stream Mach numbers of 0.1 and 0.2. The effects of boundary layer bleed inflow were investigated. A JT8D fan simulator driven by compressed air was used to pump inlet flow and to provide a characteristic noise signature. Baseline data were obtained at static free-stream conditions with the sharp P-inlet cowl lip replaced by a blunt lip. Auxiliary inlets increased overall total pressure recovery of the order of 10 percent.

A Cautious Note on Auxiliary Variables That Can Increase Bias in Missing Data Problems.

PubMed

Thoemmes, Felix; Rose, Norman

2014-01-01

The treatment of missing data in the social sciences has changed tremendously during the last decade. Modern missing data techniques such as multiple imputation and full-information maximum likelihood are used much more frequently. These methods assume that data are missing at random. One very common approach to increase the likelihood that missing at random is achieved consists of including many covariates as so-called auxiliary variables. These variables are either included based on data considerations or in an inclusive fashion; that is, taking all available auxiliary variables. In this article, we point out that there are some instances in which auxiliary variables exhibit the surprising property of increasing bias in missing data problems. In a series of focused simulation studies, we highlight some situations in which this type of biasing behavior can occur. We briefly discuss possible ways how one can avoid selecting bias-inducing covariates as auxiliary variables.

Modular error embedding

DOEpatents

Sandford, II, Maxwell T.; Handel, Theodore G.; Ettinger, J. Mark

1999-01-01

A method of embedding auxiliary information into the digital representation of host data containing noise in the low-order bits. The method applies to digital data representing analog signals, for example digital images. The method reduces the error introduced by other methods that replace the low-order bits with auxiliary information. By a substantially reverse process, the embedded auxiliary data can be retrieved easily by an authorized user through use of a digital key. The modular error embedding method includes a process to permute the order in which the host data values are processed. The method doubles the amount of auxiliary information that can be added to host data values, in comparison with bit-replacement methods for high bit-rate coding. The invention preserves human perception of the meaning and content of the host data, permitting the addition of auxiliary data in the amount of 50% or greater of the original host data.

Fuel saving and emissions cut through shore-side power concept for high-speed crafts at the red sea in egypt

NASA Astrophysics Data System (ADS)

Seddiek, Ibrahim S.; Mosleh, Mosaad A.; Banawan, Adel A.

2013-12-01

The progress of economic globalization, the rapid growth of international trade, and the maritime transportation has played an increasingly significant role in the international supply chain. As a result, worldwide seaports have suffered from a central problem, which appears in the form of massive amounts of fuel consumed and exhaust gas fumes emitted from the ships while berthed. Many ports have taken the necessary precautions to overcome this problem, while others still suffer due to the presence of technical and financial constraints. In this paper, the barriers, interconnection standards, rules, regulations, power sources, and economic and environmental analysis related to ships, shore-side power were studied in efforts to find a solution to overcome his problem. As a case study, this paper investigates the practicability, costs and benefits of switching from onboard ship auxiliary engines to shore-side power connection for high-speed crafts called Alkahera while berthed at the port of Safaga, Egypt. The results provide the national electricity grid concept as the best economical selection with 49.03 percent of annual cost saving. Moreover, environmentally, it could achieve an annual reduction in exhaust gas emissions of CO2, CO, NO x , P.M, and SO2 by 276, 2.32, 18.87, 0.825 and 3.84 tons, respectively.

The impact of (mega)-cities on the earth's gravity

NASA Astrophysics Data System (ADS)

Schnitzer, S.; Estrella, N.; Güntner, A.; Matiu, M.; Peterseim, N.; Menzel, A.

2013-12-01

The world population is constantly growing; today over 7 billion people populate the planet. This development has led to a strong urbanization and expanding cities. According to the United Nations, since 2007 more human beings have lived in urban areas than in rural areas, and by 2030 the urban share will be more than 60%. The challenges of fast growing cities lie in urban management, supply to inhabitants of resources (e.g. water, power, food), and strong environmental problems (e.g. pollution), i.e. their ecological footprint. In our study we address the question of another footprint, whether (mega)-cities have an impact on the earth's gravity field. Analyzing the possible triggers will help to understand the multiple footprints of big cities in various regions. We analyze several data sources. The main data sets are a) monthly solutions of the gravity satellite mission GRACE, detecting changes in the earth's gravity field over time, b) data of the hydrological model WGHM, estimating mass changes in terrestrial and ground water storage, c) urban population data of the United Nations, d) land cover information of the European Space Agency, e) different climate data sets and other auxiliary data. The results suggest a non-uniform pattern of gravity changes with variations in trends related to different clustering parameters.

Multiwavelength pyrometer for gray and non-gray surfaces in the presence of interfering radiation

NASA Technical Reports Server (NTRS)

Ng, Daniel L. P. (Inventor)

1994-01-01

A method and apparatus for detecting the temperature of gray and non-gray bodies in the presence of interfering radiation are presented. A gray body has a constant emissivity less than 1 and a non-gray body has an emissivity which varies with wavelength. The emissivity and reflectivity of the surface is determined over a range of wavelengths. Spectra are also measured of the extraneous interference radiation source and the surface of the object to be measured in the presence of the extraneous interference radiation source. An auxiliary radiation source is used to determine the reflectivity of the surface and also the emissivity. The measured spectrum of the surfaces in the presence of the extraneous interference radiation source is set equal to the emissivity of the surface multiplied by a Planck function containing a temperature term T plus the surface reflectivity multiplied by the spectrum of the extraneous interference radiation source. The equation is then solved for T to determine the temperature of the surface.

Some finite terms from ladder diagrams in three and four loop maximal supergravity

NASA Astrophysics Data System (ADS)

Basu, Anirban

2015-10-01

We consider the finite part of the leading local interactions in the low energy expansion of the four graviton amplitude from the ladder skeleton diagrams in maximal supergravity on T 2, at three and four loops. At three loops, we express the {D}8{{R}}4 and {D}10{{R}}4 amplitudes as integrals over the moduli space of an underlying auxiliary geometry. These amplitudes are evaluated exactly for special values of the the moduli of the auxiliary geometry, where the integrand simplifies. We also perform a similar analysis for the {D}8{{R}}4 amplitude at four loops that arise from the ladder skeleton diagrams for a special value of a parameter in the moduli space of the auxiliary geometry. While the dependence of the amplitudes on the volume of the T 2 is very simple, the dependence on the complex structure of the T 2 is quite intricate. In some of the cases, the amplitude consists of terms each of which factorizes into a product of two {SL}(2,{{Z}}) invariant modular forms. While one of the factors is a non-holomorphic Eisenstein series, the other factor splits into a sum of modular forms each of which satisfies a Poisson equation on moduli space with source terms that are bilinear in the Eisenstein series. This leads to several possible perturbative contributions unto genus 5 in type II string theory on S1. Unlike the one and two loop supergravity analysis, these amplitudes also receive non-perturbative contributions from bound states of three D-(anti)instantons in the IIB theory.

Recovery of sparse translation-invariant signals with continuous basis pursuit

PubMed Central

Ekanadham, Chaitanya; Tranchina, Daniel; Simoncelli, Eero

2013-01-01

We consider the problem of decomposing a signal into a linear combination of features, each a continuously translated version of one of a small set of elementary features. Although these constituents are drawn from a continuous family, most current signal decomposition methods rely on a finite dictionary of discrete examples selected from this family (e.g., shifted copies of a set of basic waveforms), and apply sparse optimization methods to select and solve for the relevant coefficients. Here, we generate a dictionary that includes auxiliary interpolation functions that approximate translates of features via adjustment of their coefficients. We formulate a constrained convex optimization problem, in which the full set of dictionary coefficients represents a linear approximation of the signal, the auxiliary coefficients are constrained so as to only represent translated features, and sparsity is imposed on the primary coefficients using an L1 penalty. The basis pursuit denoising (BP) method may be seen as a special case, in which the auxiliary interpolation functions are omitted, and we thus refer to our methodology as continuous basis pursuit (CBP). We develop two implementations of CBP for a one-dimensional translation-invariant source, one using a first-order Taylor approximation, and another using a form of trigonometric spline. We examine the tradeoff between sparsity and signal reconstruction accuracy in these methods, demonstrating empirically that trigonometric CBP substantially outperforms Taylor CBP, which in turn offers substantial gains over ordinary BP. In addition, the CBP bases can generally achieve equally good or better approximations with much coarser sampling than BP, leading to a reduction in dictionary dimensionality. PMID:24352562

Acylation, Diastereoselective Alkylation, and Cleavage of an Oxazolidinone Chiral Auxiliary: A Multistep Asymmetric Synthesis Experiment for Advanced Undergraduates

ERIC Educational Resources Information Center

Smith, Thomas E.; Richardson, David P.; Truran, George A.; Belecki, Katherine; Onishi, Megumi

2008-01-01

An introduction to the concepts and experimental techniques of diastereoselective synthesis using a chiral auxiliary is described. The 4-benzyl-2-oxazolidinone chiral auxiliary developed by Evans is acylated with propionic anhydride under mild conditions using DMAP as an acyl transfer catalyst. Deprotonation with NaN(TMS)[subscript 2] at -78…

Identifying Useful Auxiliary Variables for Incomplete Data Analyses: A Note on a Group Difference Examination Approach

ERIC Educational Resources Information Center

Raykov, Tenko; Marcoulides, George A.

2014-01-01

This research note contributes to the discussion of methods that can be used to identify useful auxiliary variables for analyses of incomplete data sets. A latent variable approach is discussed, which is helpful in finding auxiliary variables with the property that if included in subsequent maximum likelihood analyses they may enhance considerably…

47 CFR 15.216 - Disclosure requirements for wireless microphones and other low power auxiliary stations capable...

Code of Federal Regulations, 2010 CFR

2010-10-01

... microphones and other low power auxiliary stations capable of operating in the core TV bands. 15.216 Section... wireless microphones and other low power auxiliary stations capable of operating in the core TV bands. (a... capable of operating in the core TV bands (channels 2-51, excluding channel 37) is subject to the...

46 CFR 35.35-45 - Auxiliary steam, air, or electric current-B/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 1 2012-10-01 2012-10-01 false Auxiliary steam, air, or electric current-B/ALL. 35.35... Cargo Handling § 35.35-45 Auxiliary steam, air, or electric current—B/ALL. When discharging cargo from one or more barges, the towing vessel may furnish steam, air, or electric current for pumps on barges...

46 CFR 35.35-45 - Auxiliary steam, air, or electric current-B/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 1 2013-10-01 2013-10-01 false Auxiliary steam, air, or electric current-B/ALL. 35.35... Cargo Handling § 35.35-45 Auxiliary steam, air, or electric current—B/ALL. When discharging cargo from one or more barges, the towing vessel may furnish steam, air, or electric current for pumps on barges...

46 CFR 35.35-45 - Auxiliary steam, air, or electric current-B/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 1 2011-10-01 2011-10-01 false Auxiliary steam, air, or electric current-B/ALL. 35.35... Cargo Handling § 35.35-45 Auxiliary steam, air, or electric current—B/ALL. When discharging cargo from one or more barges, the towing vessel may furnish steam, air, or electric current for pumps on barges...

46 CFR 35.35-45 - Auxiliary steam, air, or electric current-B/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 1 2014-10-01 2014-10-01 false Auxiliary steam, air, or electric current-B/ALL. 35.35... Cargo Handling § 35.35-45 Auxiliary steam, air, or electric current—B/ALL. When discharging cargo from one or more barges, the towing vessel may furnish steam, air, or electric current for pumps on barges...

46 CFR 35.35-45 - Auxiliary steam, air, or electric current-B/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Auxiliary steam, air, or electric current-B/ALL. 35.35... Cargo Handling § 35.35-45 Auxiliary steam, air, or electric current—B/ALL. When discharging cargo from one or more barges, the towing vessel may furnish steam, air, or electric current for pumps on barges...

Data embedding employing degenerate clusters of data having differences less than noise value

DOEpatents

Sanford, II, Maxwell T.; Handel, Theodore G.

1998-01-01

A method of embedding auxiliary information into a set of host data, such as a photograph, television signal, facsimile transmission, or identification card. All such host data contain intrinsic noise, allowing pixels in the host data which are nearly identical and which have values differing by less than the noise value to be manipulated and replaced with auxiliary data. As the embedding method does not change the elemental values of the host data, the auxiliary data do not noticeably affect the appearance or interpretation of the host data. By a substantially reverse process, the embedded auxiliary data can be retrieved easily by an authorized user.

Pattern recognition monitoring of PEM fuel cell

DOEpatents

Meltser, M.A.

1999-08-31

The CO-concentration in the H{sub 2} feed stream to a PEM fuel cell stack is monitored by measuring current and voltage behavior patterns from an auxiliary cell attached to the end of the stack. The auxiliary cell is connected to the same oxygen and hydrogen feed manifolds that supply the stack, and discharges through a constant load. Pattern recognition software compares the current and voltage patterns from the auxiliary cell to current and voltage signature determined from a reference cell similar to the auxiliary cell and operated under controlled conditions over a wide range of CO-concentrations in the H{sub 2} fuel stream. 4 figs.

Pattern recognition monitoring of PEM fuel cell

DOEpatents

Meltser, Mark Alexander

1999-01-01

The CO-concentration in the H.sub.2 feed stream to a PEM fuel cell stack is monitored by measuring current and voltage behavior patterns from an auxiliary cell attached to the end of the stack. The auxiliary cell is connected to the same oxygen and hydrogen feed manifolds that supply the stack, and discharges through a constant load. Pattern recognition software compares the current and voltage patterns from the auxiliary cell to current and voltage signature determined from a reference cell similar to the auxiliary cell and operated under controlled conditions over a wide range of CO-concentrations in the H.sub.2 fuel stream.

Solar powered actuator with continuously variable auxiliary power control

NASA Technical Reports Server (NTRS)

Nola, F. J. (Inventor)

1984-01-01

A solar powered system is disclosed in which a load such as a compressor is driven by a main induction motor powered by a solar array. An auxiliary motor shares the load with the solar powered motor in proportion to the amount of sunlight available, is provided with a power factor controller for controlling voltage applied to the auxiliary motor in accordance with the loading on that motor. In one embodiment, when sufficient power is available from the solar cell, the auxiliary motor is driven as a generator by excess power from the main motor so as to return electrical energy to the power company utility lines.

Electro-aerodynamic field aided needleless electrospinning.

PubMed

Yan, Guilong; Niu, Haitao; Zhou, Hua; Wang, Hongxia; Shao, Hao; Zhao, Xueting; Lin, Tong

2018-06-08

Auxiliary fields have been used to enhance the performance of needle electrospinning. However, much less has been reported on how auxiliary fields affect needleless electrospinning. Herein, we report a novel needleless electrospinning technique that consists of an aerodynamic field and a second electric field. The second electric field is generated by setting two grounded inductive electrodes near the spinneret. The two auxiliary fields have to be applied simultaneously to ensure working of the electrospinning process. A synergistic effect was observed between inductive electrode and airflow. The aerodynamic-electric auxiliary field was found to significantly increase fiber production rate (4.5 g h -1 ), by 350% in comparison to the setup without auxiliary field (1.0 g h -1 ), whereas it had little effect on fiber diameter. The auxiliary fields allow running needleless electrospinning at an applied voltage equivalent to that in needle electrospinning (e.g. 10-30 kV). The finite element analyses of electric field and airflow field verify that the inductive electrodes increase electric field strength near the spinneret, and the airflow assists in fiber deposition. This novel needleless electrospinning may be useful for development of high-efficiency, low energy-consumption nanofiber production systems.

A Cross-Domain Collaborative Filtering Algorithm Based on Feature Construction and Locally Weighted Linear Regression

PubMed Central

Jiang, Feng; Han, Ji-zhong

2018-01-01

Cross-domain collaborative filtering (CDCF) solves the sparsity problem by transferring rating knowledge from auxiliary domains. Obviously, different auxiliary domains have different importance to the target domain. However, previous works cannot evaluate effectively the significance of different auxiliary domains. To overcome this drawback, we propose a cross-domain collaborative filtering algorithm based on Feature Construction and Locally Weighted Linear Regression (FCLWLR). We first construct features in different domains and use these features to represent different auxiliary domains. Thus the weight computation across different domains can be converted as the weight computation across different features. Then we combine the features in the target domain and in the auxiliary domains together and convert the cross-domain recommendation problem into a regression problem. Finally, we employ a Locally Weighted Linear Regression (LWLR) model to solve the regression problem. As LWLR is a nonparametric regression method, it can effectively avoid underfitting or overfitting problem occurring in parametric regression methods. We conduct extensive experiments to show that the proposed FCLWLR algorithm is effective in addressing the data sparsity problem by transferring the useful knowledge from the auxiliary domains, as compared to many state-of-the-art single-domain or cross-domain CF methods. PMID:29623088

A Cross-Domain Collaborative Filtering Algorithm Based on Feature Construction and Locally Weighted Linear Regression.

PubMed

Yu, Xu; Lin, Jun-Yu; Jiang, Feng; Du, Jun-Wei; Han, Ji-Zhong

2018-01-01

Cross-domain collaborative filtering (CDCF) solves the sparsity problem by transferring rating knowledge from auxiliary domains. Obviously, different auxiliary domains have different importance to the target domain. However, previous works cannot evaluate effectively the significance of different auxiliary domains. To overcome this drawback, we propose a cross-domain collaborative filtering algorithm based on Feature Construction and Locally Weighted Linear Regression (FCLWLR). We first construct features in different domains and use these features to represent different auxiliary domains. Thus the weight computation across different domains can be converted as the weight computation across different features. Then we combine the features in the target domain and in the auxiliary domains together and convert the cross-domain recommendation problem into a regression problem. Finally, we employ a Locally Weighted Linear Regression (LWLR) model to solve the regression problem. As LWLR is a nonparametric regression method, it can effectively avoid underfitting or overfitting problem occurring in parametric regression methods. We conduct extensive experiments to show that the proposed FCLWLR algorithm is effective in addressing the data sparsity problem by transferring the useful knowledge from the auxiliary domains, as compared to many state-of-the-art single-domain or cross-domain CF methods.

Gate drive latching circuit for an auxiliary resonant commutation circuit

NASA Technical Reports Server (NTRS)

Delgado, Eladio Clemente (Inventor); Kheraluwala, Mustansir Hussainy (Inventor)

1999-01-01

A gate drive latching circuit for an auxiliary resonant commutation circuit for a power switching inverter includes a current monitor circuit providing a current signal to a pair of analog comparators to implement latching of one of a pair of auxiliary switching devices which are used to provide commutation current for commutating switching inverters in the circuit. Each of the pair of comparators feeds a latching circuit which responds to an active one of the comparators for latching the associated gate drive circuit for one of the pair of auxiliary commutating switches. An initial firing signal is applied to each of the commutating switches to gate each into conduction and the resulting current is monitored to determine current direction and therefore the one of the switches which is carrying current. The comparator provides a latching signal to the one of the auxiliary power switches which is actually conducting current and latches that particular power switch into an on state for the duration of current through the device. The latching circuit is so designed that the only time one of the auxiliary switching devices can be latched on is during the duration of an initial firing command signal.

Electro-aerodynamic field aided needleless electrospinning

NASA Astrophysics Data System (ADS)

Yan, Guilong; Niu, Haitao; Zhou, Hua; Wang, Hongxia; Shao, Hao; Zhao, Xueting; Lin, Tong

2018-06-01

Auxiliary fields have been used to enhance the performance of needle electrospinning. However, much less has been reported on how auxiliary fields affect needleless electrospinning. Herein, we report a novel needleless electrospinning technique that consists of an aerodynamic field and a second electric field. The second electric field is generated by setting two grounded inductive electrodes near the spinneret. The two auxiliary fields have to be applied simultaneously to ensure working of the electrospinning process. A synergistic effect was observed between inductive electrode and airflow. The aerodynamic-electric auxiliary field was found to significantly increase fiber production rate (4.5 g h‑1), by 350% in comparison to the setup without auxiliary field (1.0 g h‑1), whereas it had little effect on fiber diameter. The auxiliary fields allow running needleless electrospinning at an applied voltage equivalent to that in needle electrospinning (e.g. 10–30 kV). The finite element analyses of electric field and airflow field verify that the inductive electrodes increase electric field strength near the spinneret, and the airflow assists in fiber deposition. This novel needleless electrospinning may be useful for development of high-efficiency, low energy-consumption nanofiber production systems.

A new approach for AC loss reduction in HTS transformer using auxiliary windings, case study: 25 kA HTS current injection transformer

NASA Astrophysics Data System (ADS)

Heydari, Hossein; Faghihi, Faramarz; Aligholizadeh, Reza

2008-01-01

AC loss is one of the important parameters in HTS (high temperature superconducting) AC devices. Among the HTS AC power devices, the transformer is an essential part in the electrical power system. The AC losses in an HTS tape depend on the magnetic field. One of the techniques usually adopted to mitigate the unwanted magnetic field is using a system of coils that produce a magnetic field opposite to the incident one, reducing the total magnetic field. In this paper adding two auxiliary windings to the HTS transformer to produce this opposite magnetic field is proposed. The proper use of these auxiliary windings could reduce the leakage flux and, therefore, the AC loss. A mathematical model is used to describe the behaviour of a transformer operating with auxiliary windings, based on the theory of electromagnetic coupled circuits. The influence of the auxiliary windings on the leakage field is studied by the finite element method (FEM) and the AC loss of an HTS transformer was calculated. Also, the simulation results show that employing auxiliary windings will improve the HTS transformer efficiency.

Effect of remote inductively coupled plasma (ICP) on the electron energy probability function of an in-tandem main ICP

NASA Astrophysics Data System (ADS)

Lee, Jaewon; Kim, Kyung-Hyun; Chung, Chin-Wook

2017-02-01

The remote plasma has been generally used as the auxiliary plasma source for indirect plasma processes such as cleaning or ashing. When tandem plasma sources that contain main and remote plasma sources are discharged, the main plasma is affected by the remote plasma and vice versa. Charged particles can move between two chambers due to the potential difference between the two plasmas. For this reason, the electron energy possibility function of the main plasma can be controlled by adjusting the remote plasma state. In our study, low energy electrons in the main plasma are effectively heated with varying remote plasma powers, and high energy electrons which overcome potential differences between two plasmas—are exchanged with no remarkable change in the plasma density and the effective electron temperature.

Up gradation of LHCD system for rf power level up to 2MW for SST1

NASA Astrophysics Data System (ADS)

Sharma, P. K.; Ambulkar, K. K.; Parmar, P. R.; Virani, C. G.; Thakur, A. L.; Kulkarni, S. V.; Lhcd Group

2010-02-01

To operate superconducting steadystate tokamak (SST1) for 1000 seconds, lower hybrid current drive (LHCD) system has been designed at a frequency of 3.7 GHz., which would couple 1.0 MW CW of microwave power to the shaped plasma. The system consists of various rf passive components and transmission line, employing which the rf power from the source is transported to the antenna. During calibration of transmission line, it was observed that the losses in the transmission line is substantial and eventually would lead to less coupled power to the plasma. Further it is anticipated that more LH power would be required for advanced operation of SST1 machine. Thus it is decided to upgrade the existing LHCD system to 2 MW CW power level. The proposed up gradation would demand several infra structural changes and needs to be addressed. Due to lack of space, we have proposed a scheme in which additional two klystrons, along with existing two klystrons would be accommodated in the existing space. The low rf power requirements have also been increased to cater the new needs. Accordingly additional cooling requirements have been proposed to accommodate the two new klystrons. The DAC and auxiliary power supplies have been also designed. The new up graded LHCD system would address several key technological issues. Firstly it would establish the operation of four klystrons at rated power in parallel employing single RHVPS (80kV, 70A). Secondly it would establish the operation of two high power klystrons operation at rated power when their collectors are cooled in series. In this paper we would present the various requirements for up-gradation of LHCD system to 2MW. The main requirements like high power rf source, along with modified support structure, low power rf systems to drive the high power rf source, auxiliary power supplies required for high power rf source, DAC system improvement, cooling improvements, etc. would be discussed.

Supporting the Copernicus POD Service

NASA Astrophysics Data System (ADS)

Peter, Heike; Springer, Tim; Otten, Michiel; Fernandez, Jaime; Escobar, Diego; Femenias, Pierre

2015-12-01

The Copernicus POD (Precise Orbit Determination) Service is part of the Copernicus PDGS (Payload Data Ground Segment) of the Sentinel missions. A GMV-led consortium is operating the Copernicus POD Service being in charge of generating precise orbital products and auxiliary data files for their use as part of the processing chains of the respective Sentinel PDGS. As part of the consortium PosiTim is responsible for implementing and testing software and model updates thoroughly before integrating them in the operational chain of the Copernicus POD Service. The NAPEOS (Navigation Package for Earth Observation Satellites) software is used for the generation of the orbit products within the Copernicus POD Service. The test procedures and results obtained for a recent software and model update to IERS 2010 Conventions are presented. It has been tested as well that the arc length of 72 hours for the non-time critical (NTC) orbit solutions might be shorten to 48 hours without losing accuracy. Orbit comparisons to external solutions help to validate the different orbit solutions. GPS antenna phase centre variations (PCVs) are one of the largest systematic error sources in POD. Since the satellite body may cause signal multipath a ground calibration of the GPS antenna without taking into account the satellite body might not be sufficient to quantify the PCVs. The PCVs are therefore obtained by an in-flight calibration. A first map for the PCVs determined from a limited amount of data at the beginning of the mission has shown significant multipath signals in parts of the antenna for code and carrier phase measurements. Since the satellite has moving parts it has been checked carefully if these multipath regions are moving as well or if they are antenna-fixed. Normally the correction maps are only applied for the carrier phase measurements. Since significant multipath has been spotted for the code measurements as well investigations are performed to study the impact of additionally applying code correction maps in the POD process.

Accuracy of Home-Based Ultrasonographic Diagnosis of Obstetric Risk Factors by Primary-Level Health Workers in Rural Nepal

PubMed Central

Kozuki, Naoko; Mullany, Luke C.; Khatry, Subarna K.; Ghimire, Ram K.; Paudel, Sharma; Blakemore, Karin; Bird, Christine; Tielsch, James M.; LeClerq, Steven C.; Katz, Joanne

2016-01-01

Objective To assess the feasibility of task shifting by estimating the accuracy at which primary-level health care workers can perform community-based third trimester ultrasound diagnosis for selected obstetric risk factors in rural Nepal. Methods Three auxiliary nurse midwives received two one-week ultrasound trainings at Tribhuvan University Teaching Hospital in Kathmandu. In our study site in rural Nepal, women who were ≥32 weeks in gestational age were enrolled and received ultrasound examinations from the auxiliary nurse midwives during home visits. Each auxiliary nurse midwife screened for non-cephalic presentation, multiple gestation, and placenta previa. All de-identified images were stored and uploaded onto an online server, where certified sonologists and sonographers reviewed the images and made their own diagnoses for the three conditions. Accuracy of auxiliary nurse midwife diagnoses was then calculated. Results We enrolled 804 women in the study. Each auxiliary nurse midwife’s kappa statistic for diagnosis of non-cephalic presentation was above 0.90 compared with the sonogram reviewers. Sensitivity, specificity, positive and negative predictive values were between 90–100% for all auxiliary nurse midwives For multiple gestation, the auxiliary nurse midwives were in perfect agreement with both the sonogram reviewers and maternal postpartum self-report. Two placenta previa cases were detected, and the sonogram reviewers agreed with both. Conclusion With limited training, primary-level health care workers in rural Nepal can accurately diagnose selected third trimester obstetric risk factors using ultrasonography. PMID:27500343

Optimization of coronagraph design for segmented aperture telescopes

NASA Astrophysics Data System (ADS)

Jewell, Jeffrey; Ruane, Garreth; Shaklan, Stuart; Mawet, Dimitri; Redding, Dave

2017-09-01

The goal of directly imaging Earth-like planets in the habitable zone of other stars has motivated the design of coronagraphs for use with large segmented aperture space telescopes. In order to achieve an optimal trade-off between planet light throughput and diffracted starlight suppression, we consider coronagraphs comprised of a stage of phase control implemented with deformable mirrors (or other optical elements), pupil plane apodization masks (gray scale or complex valued), and focal plane masks (either amplitude only or complex-valued, including phase only such as the vector vortex coronagraph). The optimization of these optical elements, with the goal of achieving 10 or more orders of magnitude in the suppression of on-axis (starlight) diffracted light, represents a challenging non-convex optimization problem with a nonlinear dependence on control degrees of freedom. We develop a new algorithmic approach to the design optimization problem, which we call the "Auxiliary Field Optimization" (AFO) algorithm. The central idea of the algorithm is to embed the original optimization problem, for either phase or amplitude (apodization) in various planes of the coronagraph, into a problem containing additional degrees of freedom, specifically fictitious "auxiliary" electric fields which serve as targets to inform the variation of our phase or amplitude parameters leading to good feasible designs. We present the algorithm, discuss details of its numerical implementation, and prove convergence to local minima of the objective function (here taken to be the intensity of the on-axis source in a "dark hole" region in the science focal plane). Finally, we present results showing application of the algorithm to both unobscured off-axis and obscured on-axis segmented telescope aperture designs. The application of the AFO algorithm to the coronagraph design problem has produced solutions which are capable of directly imaging planets in the habitable zone, provided end-to-end telescope system stability requirements can be met. Ongoing work includes advances of the AFO algorithm reported here to design in additional robustness to a resolved star, and other phase or amplitude aberrations to be encountered in a real segmented aperture space telescope.

A Search for the X-ray Counterpart of the Unidentified Gamma-ray Source 3EG J2020+4017 (2CG078+2)

NASA Technical Reports Server (NTRS)

Weisskopf, Martin; Swartz, Douglas A.; Carraminana, Alberto; Carrasco, Luis; Kaplan, David L.; Becker, Werner; Elsner, Ronald F.; Kanbach, Gottfried; ODell, Stephen L.; Tennant, Allyn F.

2006-01-01

We report observations with the Chandra X-ray Observatory of a field in the gamma-Cygni supernova remnant (SNR78.2+2.1) centered on the cataloged location of the unidentified, bright gamma-ray source 3EG J2020+4017. In this search for an X-ray counterpart to the gamma-ray source, we detected 30 X-ray sources. Of these, we found 17 strong-candidate counterparts in optical (visible through near-infrared) cataloged and an additional 3 through our optical observations. Based upon colors and (for several objects) optical spectra, nearly all the optically identified objects appear to be reddened main-sequence stars: None of the X-ray sources with an optical counterpart is a plausible X-ray counterpart to 3EG J2020+4017-if that gamma-ray source is a spin-powered pulsar. Many of the 10 X-ray sources lacking optical counterparts are likely (extragalactic) active galactic nuclei, based upon the sky density of such sources. Although one of the 10 optically unidentified X-ray sources could be the gamma-ray source, there is no auxiliary evidence supporting such an identification

Numerical methods for solving moment equations in kinetic theory of neuronal network dynamics

NASA Astrophysics Data System (ADS)

Rangan, Aaditya V.; Cai, David; Tao, Louis

2007-02-01

Recently developed kinetic theory and related closures for neuronal network dynamics have been demonstrated to be a powerful theoretical framework for investigating coarse-grained dynamical properties of neuronal networks. The moment equations arising from the kinetic theory are a system of (1 + 1)-dimensional nonlinear partial differential equations (PDE) on a bounded domain with nonlinear boundary conditions. The PDEs themselves are self-consistently specified by parameters which are functions of the boundary values of the solution. The moment equations can be stiff in space and time. Numerical methods are presented here for efficiently and accurately solving these moment equations. The essential ingredients in our numerical methods include: (i) the system is discretized in time with an implicit Euler method within a spectral deferred correction framework, therefore, the PDEs of the kinetic theory are reduced to a sequence, in time, of boundary value problems (BVPs) with nonlinear boundary conditions; (ii) a set of auxiliary parameters is introduced to recast the original BVP with nonlinear boundary conditions as BVPs with linear boundary conditions - with additional algebraic constraints on the auxiliary parameters; (iii) a careful combination of two Newton's iterates for the nonlinear BVP with linear boundary condition, interlaced with a Newton's iterate for solving the associated algebraic constraints is constructed to achieve quadratic convergence for obtaining the solutions with self-consistent parameters. It is shown that a simple fixed-point iteration can only achieve a linear convergence for the self-consistent parameters. The practicability and efficiency of our numerical methods for solving the moment equations of the kinetic theory are illustrated with numerical examples. It is further demonstrated that the moment equations derived from the kinetic theory of neuronal network dynamics can very well capture the coarse-grained dynamical properties of integrate-and-fire neuronal networks.

[Advances in the use of instrumental measurement of colour in the development, production and quality control of drugs, medicinal preparations and pharmaceutical auxiliary substances I ].

PubMed

Subert, Jan; Cižmárik, Jozef

2013-04-01

Colour is one of the important indices of the quality of drugs, medicinal preparations and pharmaceutical auxiliary substances. The paper summarizes the development and use of instrumental measurement of colour in pharmacy in recent ten years focusing on the drugs of synthetic origin and pharmaceutical auxiliary substances including their control.

STS-31: APU Controller Removal

NASA Technical Reports Server (NTRS)

1990-01-01

The launch April 10 of the STS-31 was scrubbed at T-4 minutes due to a faulty valve in auxiliary power unit (APU) number one. The auxiliary power unit is a hydrazine-fueled, turbine-driven power unit that generates mechanical shaft power to drive a hydraulic pump that produces pressure for the orbiter's hydraulic system. This video shows the removal of the STS-31's auxiliary power unit (APU).

30 CFR 57.22208 - Auxiliary fans (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Auxiliary fans (I-A, II-A, III, and V-A mines). 57.22208 Section 57.22208 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... fans (I-A, II-A, III, and V-A mines). (a) Auxiliary fans, except fans used in shops and other areas...

Teaching Grammar: The Use of The English Auxiliary "BE" Present Tense Verb among Malaysian Form 4 and Form 5 Students

ERIC Educational Resources Information Center

Jishvithaa, Joanna M.; Tabitha, M.; Kalajahi, Seyed Ali Rezvani

2013-01-01

This research paper aims to explore the usage of the English Auxiliary "Be" Present Tense Verb, using corpus based method among Malaysian form 4 and form 5 students. This study is conducted by identifying and classifying the types of errors in the Auxiliary "Be" Present Tense verb in students' compositions from the MCSAW corpus…

46 CFR 11.454 - Service requirements for mate of Great Lakes and inland steam or motor vessels of not more than...

Code of Federal Regulations, 2011 CFR

2011-10-01

... gross tons is six months of service in the deck department of steam or motor, sail, or auxiliary sail... United States (excluding the Great Lakes). (b) In order to obtain an endorsement for sail or auxiliary sail vessels, the applicant must submit evidence of three months of service on sail or auxiliary sail...

46 CFR 11.428 - Service requirements for master of near coastal steam or motor vessels of not more than 100 gross...

Code of Federal Regulations, 2011 CFR

2011-10-01

... total service in the deck department of steam or motor, sail, or auxiliary sail vessels on ocean or near... service. (b) In order to obtain an endorsement for sail or auxiliary sail vessels, the applicant must submit evidence of 12 months of service on sail or auxiliary sail vessels. The required 12 months of...

46 CFR 11.454 - Service requirements for mate of Great Lakes and inland steam or motor vessels of not more than...

Code of Federal Regulations, 2010 CFR

2010-10-01

... gross tons is six months of service in the deck department of steam or motor, sail, or auxiliary sail... United States (excluding the Great Lakes). (b) In order to obtain an endorsement for sail or auxiliary sail vessels, the applicant must submit evidence of three months of service on sail or auxiliary sail...

46 CFR 11.427 - Service requirements for mate of near coastal steam or motor vessels of not more than 200 gross...

Code of Federal Regulations, 2011 CFR

2011-10-01

... total service in the deck department of ocean or near coastal steam or motor, sail, or auxiliary sail... of inland steam or motor, sail or auxiliary sail vessels of not more than 200 gross tons. (b) The... regulations for small passenger vessels. (c) In order to obtain this officer endorsement for sail or auxiliary...

46 CFR 11.427 - Service requirements for mate of near coastal steam or motor vessels of not more than 200 gross...

Code of Federal Regulations, 2010 CFR

2010-10-01

... total service in the deck department of ocean or near coastal steam or motor, sail, or auxiliary sail... of inland steam or motor, sail or auxiliary sail vessels of not more than 200 gross tons. (b) The... regulations for small passenger vessels. (c) In order to obtain this officer endorsement for sail or auxiliary...

46 CFR 11.428 - Service requirements for master of near coastal steam or motor vessels of not more than 100 gross...

Code of Federal Regulations, 2010 CFR

2010-10-01

... total service in the deck department of steam or motor, sail, or auxiliary sail vessels on ocean or near... service. (b) In order to obtain an endorsement for sail or auxiliary sail vessels, the applicant must submit evidence of 12 months of service on sail or auxiliary sail vessels. The required 12 months of...

New conformal mapping for adaptive resolving of the complex singularities of Stokes wave

PubMed Central

Dyachenko, Sergey A.; A. Silantyev, Denis

2017-01-01

A new highly efficient method is developed for computation of travelling periodic waves (Stokes waves) on the free surface of deep water. A convergence of numerical approximation is determined by the complex singularities above the free surface for the analytical continuation of the travelling wave into the complex plane. An auxiliary conformal mapping is introduced which moves singularities away from the free surface thus dramatically speeding up numerical convergence by adapting the numerical grid for resolving singularities while being consistent with the fluid dynamics. The efficiency of that conformal mapping is demonstrated for the Stokes wave approaching the limiting Stokes wave (the wave of the greatest height) which significantly expands the family of numerically accessible solutions. It allows us to provide a detailed study of the oscillatory approach of these solutions to the limiting wave. Generalizations of the conformal mapping to resolve multiple singularities are also introduced. PMID:28690418

New conformal mapping for adaptive resolving of the complex singularities of Stokes wave.

PubMed

Lushnikov, Pavel M; Dyachenko, Sergey A; A Silantyev, Denis

2017-06-01

A new highly efficient method is developed for computation of travelling periodic waves (Stokes waves) on the free surface of deep water. A convergence of numerical approximation is determined by the complex singularities above the free surface for the analytical continuation of the travelling wave into the complex plane. An auxiliary conformal mapping is introduced which moves singularities away from the free surface thus dramatically speeding up numerical convergence by adapting the numerical grid for resolving singularities while being consistent with the fluid dynamics. The efficiency of that conformal mapping is demonstrated for the Stokes wave approaching the limiting Stokes wave (the wave of the greatest height) which significantly expands the family of numerically accessible solutions. It allows us to provide a detailed study of the oscillatory approach of these solutions to the limiting wave. Generalizations of the conformal mapping to resolve multiple singularities are also introduced.

Preparation of uniaxially aligned TiO2 ultrafine fibers by electrospinning.

PubMed

Nien, Yu-Hsun; Tsai, Yan-Sheng; Wang, Jia-Yi; Syu, Shu-Ping

2012-11-01

TiO2 nanofibers are often produced by electrospinning using a collector consisting of two parallel electrodes. In this work, a high speed rotating drum was used as a collector to produce uniaxially aligned TiO2 ultrafine fibers. The apparatus to manufacture uniaxially aligned TiO2 ultrafine fiber consisted of a high-speed roller, a high-voltage power supply, a controllable syringe pump and a syringe. Titanium (IV) isopropoxide and polyvinylpyrrolidone were used as precursor and auxiliary, respectively. Titanium (IV) isopropoxide and polyvinylpyrrolidone were well mixed with other essential reagents to form the polymer solution. The polymer solution was poured into the syringe and pumped at various flow rates. The electrospun ultrafine fibers collected on the roller were heat treated up to 600 degrees C and the uniaxially aligned TiO2 ultrafine fibers were formed and characterized using scanning electron microscope and X-ray diffraction.

Minimal wave speed for a class of non-cooperative reaction-diffusion systems of three equations

NASA Astrophysics Data System (ADS)

Zhang, Tianran

2017-05-01

In this paper, we study the traveling wave solutions and minimal wave speed for a class of non-cooperative reaction-diffusion systems consisting of three equations. Based on the eigenvalues, a pair of upper-lower solutions connecting only the invasion-free equilibrium are constructed and the Schauder's fixed-point theorem is applied to show the existence of traveling semi-fronts for an auxiliary system. Then the existence of traveling semi-fronts of original system is obtained by limit arguments. The traveling semi-fronts are proved to connect another equilibrium if natural birth and death rates are not considered and to be persistent if these rates are incorporated. Then non-existence of bounded traveling semi-fronts is obtained by two-sided Laplace transform. Then the above results are applied to some disease-transmission models and a predator-prey model.

Brane - Anti-Brane Democracy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajaraman, Arvind

2003-06-02

We suggest a duality invariant formula for the entropy and temperature of nonextreme black holes in supersymmetric string theory. The entropy is given in terms of the duality invariant parameter of the deviation from extremality and 56 SU(8) covariant central charges. It interpolates between the entropies of Schwarzschild solution and extremal solutions with various amount of unbroken supersymmetries and therefore serves for classification of black holes in supersymmetric string theories. We introduce the second auxiliary 56 via E(7) symmetric constraint. The symmetric and antisymmetric combinations of these two multiplets are related via moduli to the corresponding two fundamental representations ofmore » E(7): brane and anti-brane ''numbers.'' Using the CPT as well as C symmetry of the entropy formula and duality one can explain the mysterious simplicity of the non-extreme black hole area formula in terms of branes and anti-branes.« less

Transient responses' optimization by means of set-based multi-objective evolution

NASA Astrophysics Data System (ADS)

Avigad, Gideon; Eisenstadt, Erella; Goldvard, Alex; Salomon, Shaul

2012-04-01

In this article, a novel solution to multi-objective problems involving the optimization of transient responses is suggested. It is claimed that the common approach of treating such problems by introducing auxiliary objectives overlooks tradeoffs that should be presented to the decision makers. This means that, if at some time during the responses, one of the responses is optimal, it should not be overlooked. An evolutionary multi-objective algorithm is suggested in order to search for these optimal solutions. For this purpose, state-wise domination is utilized with a new crowding measure for ordered sets being suggested. The approach is tested on both artificial as well as on real life problems in order to explain the methodology and demonstrate its applicability and importance. The results indicate that, from an engineering point of view, the approach possesses several advantages over existing approaches. Moreover, the applications highlight the importance of set-based evolution.

Lack of high-quality studies comparing the effectiveness, and cost-effectiveness, of dental auxiliaries and dentists in performing dental care.

PubMed

Richards, Derek

2015-03-01

Cochrane Effective Practice and Organisation of Care (EPOC) Group's Specialised Register; Cochrane Oral Health Group's Specialised Register; the Cochrane Central Register of Controlled Trials Medline; Embase; CINAHL; Cochrane Database of Systematic Reviews; Database of Abstracts of Reviews of Effectiveness; five other databases and two trial registries. A number of dental journals were hand-searched and a grey literature search preformed. Randomised controlled trials (RCTs), non-randomised controlled trials (NRCTs), controlled before and after studies (CBAs) and interrupted time series (ITSs) were considered. Selection was conducted independently by two reviewers. Three reviewers extracted data and assessed risk of bias. Meta-analysis was not possible so a narrative summary was presented. Four studies evaluated sealant placement; three found no evidence of a difference in retention rates of those placed by dental auxiliaries and dentists over a range of follow-up periods (six to 24 months). One study found that sealants placed by a dental auxiliary had lower retention rates than ones placed by a dentist after 48 months (9.0% with auxiliary versus 29.1% with dentist); but the net reduction in the number of teeth exhibiting caries was lower for teeth treated by the dental auxiliary than the dentist (three with auxiliary versus 60 with dentist, P value < 0.001). One study showed no evidence of a difference in dental decay after treatment with fissure sealants between groups. One study comparing the effectiveness of dental auxiliaries and dentists performing ART reported no difference in survival rates of the restorations (fillings) after 12 months. We only identified five studies for inclusion in this review, all of which were at high risk of bias, and four were published more than 20 years ago, highlighting the paucity of high-quality evaluations of the relative effectiveness, cost-effectiveness and safety of dental auxiliaries compared with dentists in performing clinical tasks. No firm conclusions could be drawn from the present review about the relative effectiveness of dental auxiliaries and dentists.

Data embedding employing degenerate clusters of data having differences less than noise value

DOEpatents

Sanford, M.T. II; Handel, T.G.

1998-10-06

A method of embedding auxiliary information into a set of host data, such as a photograph, television signal, facsimile transmission, or identification card. All such host data contain intrinsic noise, allowing pixels in the host data which are nearly identical and which have values differing by less than the noise value to be manipulated and replaced with auxiliary data. As the embedding method does not change the elemental values of the host data, the auxiliary data do not noticeably affect the appearance or interpretation of the host data. By a substantially reverse process, the embedded auxiliary data can be retrieved easily by an authorized user. 35 figs.

Using heteroaryl-lithium reagents as hydroxycarbonyl anion equivalents in conjugate addition reactions with (S,S)-(+)-pseudoephedrine as chiral auxiliary; enantioselective synthesis of 3-substituted pyrrolidines.

PubMed

Alonso, Beatriz; Ocejo, Marta; Carrillo, Luisa; Vicario, Jose L; Reyes, Efraim; Uria, Uxue

2013-01-18

We have developed an efficient protocol for carrying out the stereocontrolled formal conjugate addition of hydroxycarbonyl anion equivalents to α,β-unsaturated carboxylic acid derivatives using (S,S)-(+)-pseudoephedrine as chiral auxiliary, making use of the synthetic equivalence between the heteroaryl moieties and the carboxylate group. This protocol has been applied as key step in the enantioselective synthesis of 3-substituted pyrrolidines in which, after removing the chiral auxiliary, the heteroaryl moiety is converted into a carboxylate group followed by reduction and double nucleophilic displacement. Alternatively, the access to the same type of heterocyclic scaffold but with opposite absolute configuration has also been accomplished by making use of the regio- and diastereoselective conjugate addition of organolithium reagents to α,β,γ,δ-unsaturated amides derived from the same chiral auxiliary followed by chiral auxiliary removal, ozonolysis, and reductive amination/intramolecular nucleophilic displacement sequence.

Simulation and energy analysis of distributed electric heating system

NASA Astrophysics Data System (ADS)

Yu, Bo; Han, Shenchao; Yang, Yanchun; Liu, Mingyuan

2018-02-01

Distributed electric heating system assistssolar heating systemby using air-source heat pump. Air-source heat pump as auxiliary heat sourcecan make up the defects of the conventional solar thermal system can provide a 24 - hour high - efficiency work. It has certain practical value and practical significance to reduce emissions and promote building energy efficiency. Using Polysun software the system is simulated and compared with ordinary electric boiler heating system. The simulation results show that upon energy request, 5844.5kW energy is saved and 3135kg carbon - dioxide emissions are reduced and5844.5 kWhfuel and energy consumption is decreased with distributed electric heating system. Theeffect of conserving energy and reducing emissions using distributed electric heating systemis very obvious.

Full-spectrum multiwavelength pyrometry for nongray surfaces

NASA Technical Reports Server (NTRS)

Ng, Daniel; Williams, W. D.

1992-01-01

A full-spectrum (encompassing radiation on both sides of the Wien displacement peak) multiwavelength pyrometer was developed. It measures the surface temperature of arbitrary nongray ceramics by curve fitting a spectrum in this spectral region to a Planck function of temperature T. This function of T is modified by the surface spectral emissivity. The emissivity function was derived experimentally from additional spectra that were obtained by using an auxiliary radiation source and from application of Kirchhoff's law. This emissivity was verified by results that were obtained independently by using electromagnetic and solid-state theories. In the presence of interfering reflected radiation this general pyrometry improves the accuracy of the measured temperature by measuring an additional spectrum that characterizes the interfering radiation source.

Dental auxiliaries for dental care traditionally provided by dentists.

PubMed

Dyer, Tom A; Brocklehurst, Paul; Glenny, Anne-Marie; Davies, Linda; Tickle, Martin; Issac, Ansy; Robinson, Peter G

2014-08-20

Poor or inequitable access to oral health care is commonly reported in high-, middle- and low-income countries. Although the severity of these problems varies, a lack of supply of dentists and their uneven distribution are important factors. Delegating care to dental auxiliaries could ease this problem, extend services to where they are unavailable and liberate time for dentists to do more complex work. Before such an approach can be advocated, it is important to know the relative effectiveness of dental auxiliaries and dentists. To assess the effectiveness, costs and cost effectiveness of dental auxiliaries in providing care traditionally provided by dentists. We searched the following electronic databases from their inception dates up to November 2013: the Cochrane Effective Practice and Organisation of Care (EPOC) Group's Specialised Register; Cochrane Oral Health Group's Specialised Register; the Cochrane Central Register of Controlled Trials (Issue 11, 2013); MEDLINE; EMBASE; CINAHL; Cochrane Database of Systematic Reviews; Database of Abstracts of Reviews of Effectiveness; five other databases and two trial registries. We also undertook a grey literature search and searched the reference list of included studies and contacted authors of relevant papers. We included randomised controlled trials (RCTs), non-randomised controlled clinical trials (NRCTs), interrupted time series (ITSs) and controlled before and after studies (CBAs) evaluating the effectiveness of dental auxiliaries compared with dentists in undertaking clinical tasks traditionally performed by a dentist. Three review authors independently applied eligibility criteria, extracted data and assessed the risk of bias of each included study and two review authors assessed the quality of the evidence from the included studies, according to The Cochrane Collaboration's procedures. Since meta-analysis was not possible, we gave a narrative description of the results. We identified five studies (one cluster RCT, three RCTs and one NRCT), evaluating the effectiveness of dental auxiliaries compared with dentists in providing dental care traditionally provided by dentists, eligible for inclusion in this review. The included studies, which involved 13 dental auxiliaries, six dentists, and more than 1156 participants, evaluated two clinical tasks/techniques: placement of preventive resin fissure sealants and the atraumatic restorative technique (ART). Two studies were conducted in the US, and one each in Canada, Gambia and Singapore.Of the four studies evaluating effectiveness in placing preventive resin fissure sealants, three found no evidence of a difference in retention rates of those placed by dental auxiliaries and dentists over a range of follow-up periods (six to 24 months). One study found that fissure sealants placed by a dental auxiliary had lower retention rates than one placed by a dentist after 48 months (9.0% with auxiliary versus 29.1% with dentist). The same study reported that the net reduction after 48 months in the number teeth exhibiting caries (dental decay) was lower for teeth treated by the dental auxiliary than the dentist (3 with auxiliary versus 60 with dentist, P value < 0.001).One study showed no evidence of a difference in dental decay after treatment with fissure sealants between groups. The one study comparing the effectiveness of dental auxiliaries and dentists in performing ART reported no difference in survival rates of the restorations (fillings) after 12 months.All studies were at high risk of bias and the overall quality of the evidence was very low, as assessed using the GRADE approach. In addition, four of the included studies were more than 20 years old; the materials used and the techniques assessed were out of date. We found no eligible studies comparing the effectiveness of dental auxiliaries and dentists in the diagnosis of oral diseases and conditions, in delivering oral health education and other aspects of health promotion, or studies assessing participants' perspectives including the acceptability of care received. None of the included studies reported adverse effects. In addition, we found no studies comparing the costs and cost-effectiveness of dental auxiliaries and dentists, their impact on access and equity of access to care that met the pre-specified inclusion criteria. We only identified five studies for inclusion in this review, all of which were at high risk of bias and four were published more than 20 years ago, highlighting the paucity of high-quality evaluations of the relative effectiveness, cost-effectiveness and safety of dental auxiliaries compared with dentists in performing clinical tasks. No firm conclusions could be drawn from the present review about the relative effectiveness of dental auxiliaries and dentists.

Photoremovable chiral auxiliary.

PubMed

Kammath, Viju Balachandran; Sebej, Peter; Slanina, Tomáš; Kříž, Zdeněk; Klán, Petr

2012-03-01

A new concept of a photoremovable chiral auxiliary (PCA), based on the chiral benzoin chromophore, is introduced. This moiety can control the asymmetric formation of a Diels-Alder adduct, and then be removed in a subsequent photochemical step in high chemical and quantum yields. Selective formation of the products at up to 96% ee was observed in the presence of a Lewis acid catalyst in the case of a 2-methoxybenzoinyl chiral auxiliary.

Sensitivity to Morphosyntactic Information in 3-Year-Old Children With Typical Language Development: A Feasibility Study.

PubMed

Deevy, Patricia; Leonard, Laurence B; Marchman, Virginia A

2017-03-01

This study tested the feasibility of a method designed to assess children's sensitivity to tense/agreement information in fronted auxiliaries during online comprehension of questions (e.g., Are the nice little dogs running?). We expected that a group of children who were proficient in auxiliary use would show this sensitivity, indicating an awareness of the relation between the subject-verb sequence (e.g., dogs running) and preceding information (e.g., are). Failure to grasp this relation is proposed to play a role in the protracted inconsistency in auxiliary use in children with specific language impairment (SLI). Fifteen 3-year-old typically developing children who demonstrated proficiency in auxiliary use viewed pairs of pictures showing a single agent and multiple agents while hearing questions with or without an agreeing fronted auxiliary. Proportion looking to the target was measured. Children showed anticipatory looking on the basis of the number information contained in the auxiliary (is or are). The children tested in this study represent a group that frequently serves as a comparison for older children with SLI. Because the method successfully demonstrated their sensitivity to tense/agreement information in questions, future research that involves direct comparisons of these 2 groups is warranted.

Diverse Roles for Auxiliary Subunits in Phosphorylation-Dependent Regulation of Mammalian Brain Voltage-Gated Potassium Channels

PubMed Central

Vacher, Helene; Trimmer, James S.

2012-01-01

Voltage-gated ion channels are a diverse family of signaling proteins that mediate rapid electrical signaling events. Among these, voltage-gated potassium or Kv channels are the most diverse, in part due to the large number of principal (or α) subunits and auxiliary subunits that can assemble in different combinations to generate Kv channel complexes with distinct structures and functions. The diversity of Kv channels underlies much of the variability in the active properties between different mammalian central neurons, and the dynamic changes that lead to experience-dependent plasticity in intrinsic excitability. Recent studies have revealed that Kv channel α subunits and auxiliary subunits are extensively phosphorylated, contributing to additional structural and functional diversity. Here we highlight recent studies that show that auxiliary subunits exert some of their profound effects on dendritic Kv4 and axonal Kv1 channels through phosphorylation-dependent mechanisms, either due to phosphorylation on the auxiliary subunit itself, or by influencing the extent and/or impact of α subunit phosphorylation. The complex effects of auxiliary subunits and phosphorylation provide a potent mechanism to generate additional diversity in the structure and function of Kv4 and Kv1 channels, as well as allowing for dynamic reversible regulation of these important ion channels. PMID:21822597

Refinement of current monitoring methodology for electroosmotic flow assessment under low ionic strength conditions

PubMed Central

Saucedo-Espinosa, Mario A.; Lapizco-Encinas, Blanca H.

2016-01-01

Current monitoring is a well-established technique for the characterization of electroosmotic (EO) flow in microfluidic devices. This method relies on monitoring the time response of the electric current when a test buffer solution is displaced by an auxiliary solution using EO flow. In this scheme, each solution has a different ionic concentration (and electric conductivity). The difference in the ionic concentration of the two solutions defines the dynamic time response of the electric current and, hence, the current signal to be measured: larger concentration differences result in larger measurable signals. A small concentration difference is needed, however, to avoid dispersion at the interface between the two solutions, which can result in undesired pressure-driven flow that conflicts with the EO flow. Additional challenges arise as the conductivity of the test solution decreases, leading to a reduced electric current signal that may be masked by noise during the measuring process, making for a difficult estimation of an accurate EO mobility. This contribution presents a new scheme for current monitoring that employs multiple channels arranged in parallel, producing an increase in the signal-to-noise ratio of the electric current to be measured and increasing the estimation accuracy. The use of this parallel approach is particularly useful in the estimation of the EO mobility in systems where low conductivity mediums are required, such as insulator based dielectrophoresis devices. PMID:27375813

Application of cyanuric chloride-based six new chiral derivatizing reagents having amino acids and amino acid amides as chiral auxiliaries for enantioresolution of proteinogenic amino acids by reversed-phase high-performance liquid chromatography.

PubMed

Bhushan, Ravi; Dixit, Shuchi

2012-04-01

Six dichloro-s-triazine (DCT) reagents having L-Leu, D-Phg, L-Val, L-Met, L-Ala and L-Met-NH(2) as chiral auxiliaries in cyanuric chloride were introduced for enantioseparation of 13 proteinogenic amino acids. Four other DCTs and six monochloro-s-triazine (MCT) reagents having amino acid amides as chiral auxiliaries were also synthesized. These 16 chiral derivatizing reagents (CDRs) were used for synthesis of diastereomers of all the 13 analytes using microwave irradiation, which were resolved by reversed-phase high-performance liquid chromatography (RP-HPLC) using C18 column and gradient eluting mixture of aqueous TFA and acetonitrile with UV detection at 230 nm. It required only 60-90 s for derivatization using microwave irradiation. Better resolution and lower retention times were observed for the diastereomers prepared with CDRs having amino acids as chiral auxiliaries as compared to counterparts prepared with reagents having amino acid amides as chiral auxiliaries. As the best resolution of all the 13 analytes was observed for their diastereomers prepared using the DCT reagent having L-Leu as chiral auxiliary, this CDR was further employed for derivatization of Lys, Tyr, His and Arg followed by RP-HPLC analysis of resulting diastereomers. The results are discussed in light of acid and amide groups of chiral auxiliaries constituting CDRs, electronegativities of the atoms of achiral moieties constituting CDRs and hydrophobicities of side chains of amino acids constituting CDRs and analytes.

Neutron diffraction as a tool to monitor the establishment of the electro-osmotic flux during realkalisation of carbonated concrete

NASA Astrophysics Data System (ADS)

Castellote, Marta; Llorente, I.; Andrade, Carmen; Turrillas, X.; Alonso, Cruz; Campo, Javier

2006-11-01

Realkalisation is an electrochemical technique for repairing concrete structures damaged by rebar corrosion due to carbonation. The treatment aims at restoring alkalinity of the concrete by application of a continuous current between the rebar, acting as a cathode, and an external auxiliary electrode placed in a carbonate solution and connected to a positive pole of a power supply. Here we report the application of neutron diffraction in the in situ monitoring of a realkalisation treatment, analysing at the same time the development of the electro-osmotic flux and the microstructural variations in the surroundings of the rebar.

Research on the supercapacitor support schemes for LVRT of variable-frequency drive in the thermal power plant

NASA Astrophysics Data System (ADS)

Han, Qiguo; Zhu, Kai; Shi, Wenming; Wu, Kuayu; Chen, Kai

2018-02-01

In order to solve the problem of low voltage ride through(LVRT) of the major auxiliary equipment’s variable-frequency drive (VFD) in thermal power plant, the scheme of supercapacitor paralleled in the DC link of VFD is put forward, furthermore, two solutions of direct parallel support and voltage boost parallel support of supercapacitor are proposed. The capacitor values for the relevant motor loads are calculated according to the law of energy conservation, and they are verified by Matlab simulation. At last, a set of test prototype is set up, and the test results prove the feasibility of the proposed schemes.

Node Immunization with Time-Sensitive Restrictions.

PubMed

Cui, Wen; Gong, Xiaoqing; Liu, Chen; Xu, Dan; Chen, Xiaojiang; Fang, Dingyi; Tang, Shaojie; Wu, Fan; Chen, Guihai

2016-12-15

When we encounter a malicious rumor or an infectious disease outbreak, immunizing k nodes of the relevant network with limited resources is always treated as an extremely effective method. The key challenge is how we can insulate limited nodes to minimize the propagation of those contagious things. In previous works, the best k immunised nodes are selected by learning the initial status of nodes and their strategies even if there is no feedback in the propagation process, which eventually leads to ineffective performance of their solutions. In this paper, we design a novel vaccines placement strategy for protecting much more healthy nodes from being infected by infectious nodes. The main idea of our solution is that we are not only utilizing the status of changing nodes as auxiliary knowledge to adjust our scheme, but also comparing the performance of vaccines in various transmission slots. Thus, our solution has a better chance to get more benefit from these limited vaccines. Extensive experiments have been conducted on several real-world data sets and the results have shown that our algorithm has a better performance than previous works.

Node Immunization with Time-Sensitive Restrictions

PubMed Central

Cui, Wen; Gong, Xiaoqing; Liu, Chen; Xu, Dan; Chen, Xiaojiang; Fang, Dingyi; Tang, Shaojie; Wu, Fan; Chen, Guihai

2016-01-01

When we encounter a malicious rumor or an infectious disease outbreak, immunizing k nodes of the relevant network with limited resources is always treated as an extremely effective method. The key challenge is how we can insulate limited nodes to minimize the propagation of those contagious things. In previous works, the best k immunised nodes are selected by learning the initial status of nodes and their strategies even if there is no feedback in the propagation process, which eventually leads to ineffective performance of their solutions. In this paper, we design a novel vaccines placement strategy for protecting much more healthy nodes from being infected by infectious nodes. The main idea of our solution is that we are not only utilizing the status of changing nodes as auxiliary knowledge to adjust our scheme, but also comparing the performance of vaccines in various transmission slots. Thus, our solution has a better chance to get more benefit from these limited vaccines. Extensive experiments have been conducted on several real-world data sets and the results have shown that our algorithm has a better performance than previous works. PMID:27983680

Geothermal energy control system and method

DOEpatents

Matthews, Hugh B.

1977-01-01

A geothermal energy transfer and utilization system makes use of thermal energy stored in hot solute-bearing well water to generate super-heated steam from an injected flow of clean water; the super-heated steam is then used for operating a turbine-driven pump at the well bottom for pumping the hot solute-bearing water at high pressure and in liquid state to the earth's surface, where it is used by transfer of its heat to a closed-loop boiler-turbine-alternator combination for the generation of electrical or other power. Residual concentrated solute-bearing water is pumped back into the earth. The clean cooled water is regenerated at the surface-located system and is returned to the deep well pumping system also for lubrication of a novel bearing arrangement supporting the turbine-driven pump system. The bearing system employs liquid lubricated thrust and radial bearings with all bearing surfaces bathed in clean water serving as a lubricant and maintained under pressure to prevent entry into the bearings of contaminated geothermal fluid, an auxiliary thrust ball bearing arrangement comes into operation when starting or stopping the pumping system.

Balance Maintenance in High-Speed Motion of Humanoid Robot Arm-Based on the 6D Constraints of Momentum Change Rate

PubMed Central

Zhang, Da-song; Chu, Jian

2014-01-01

Based on the 6D constraints of momentum change rate (CMCR), this paper puts forward a real-time and full balance maintenance method for the humanoid robot during high-speed movement of its 7-DOF arm. First, the total momentum formula for the robot's two arms is given and the momentum change rate is defined by the time derivative of the total momentum. The author also illustrates the idea of full balance maintenance and analyzes the physical meaning of 6D CMCR and its fundamental relation to full balance maintenance. Moreover, discretization and optimization solution of CMCR has been provided with the motion constraint of the auxiliary arm's joint, and the solving algorithm is optimized. The simulation results have shown the validity and generality of the proposed method on the full balance maintenance in the 6 DOFs of the robot body under 6D CMCR. This method ensures 6D dynamics balance performance and increases abundant ZMP stability margin. The resulting motion of the auxiliary arm has large abundance in joint space, and the angular velocity and the angular acceleration of these joints lie within the predefined limits. The proposed algorithm also has good real-time performance. PMID:24883404

[On teaching the chemistry of pharmaceutical auxiliary substances within the framework of pharmaceutical education in the Czech and Slovak Republics].

PubMed

Jan, Subert

2011-02-01

The paper emphasizes the need of the introduction of the subject Chemistry of Pharmaceutical Auxiliaries into the Pharmacy study programme at more colleges in the Czech and Slovak Republics. It also introduces and discusses some topics for possible extension of the content of the courses of the subject (the presented examples are taken form the field of analytical chemistry of pharmaceutical auxiliaries).

Permanent split capacitor single phase electric motor system

DOEpatents

Kirschbaum, Herbert S.

1984-01-01

A permanent split capacitor single phase electric motor achieves balanced operation at more than one operating point by adjusting the voltage supplied to the main and auxiliary windings and adjusting the capacitance in the auxiliary winding circuit. An intermediate voltage tap on an autotransformer supplies voltage to the main winding for low speed operation while a capacitive voltage divider is used to adjust the voltage supplied to the auxiliary winding for low speed operation.

Preliminary design of an auxiliary power unit for the space shuttle. Volume 4: Selected system supporting studies

NASA Technical Reports Server (NTRS)

Hamilton, M. L.; Burriss, W. L.

1972-01-01

Selected system supporting analyses in conjunction with the preliminary design of an auxiliary power unit (APU) for the space shuttle are presented. Both steady state and transient auxiliary power unit performance, based on digital computer programs, were examined. The selected APU provides up to 400 horsepower out of the gearbox, weighs 227 pounds, and requires 2 pounds per shaft horsepower hour of propellants.

Cooling system for a nuclear reactor

DOEpatents

Amtmann, Hans H.

1982-01-01

A cooling system for a gas-cooled nuclear reactor is disclosed which includes at least one primary cooling loop adapted to pass coolant gas from the reactor core and an associated steam generator through a duct system having a main circulator therein, and at least one auxiliary cooling loop having communication with the reactor core and adapted to selectively pass coolant gas through an auxiliary heat exchanger and circulator. The main and auxiliary circulators are installed in a common vertical cavity in the reactor vessel, and a common return duct communicates with the reactor core and intersects the common cavity at a junction at which is located a flow diverter valve operative to effect coolant flow through either the primary or auxiliary cooling loops.

Aeronautical fuel conservation possibilities for advanced subsonic transports. [application of aeronautical technology for drag and weight reduction

NASA Technical Reports Server (NTRS)

Braslow, A. L.; Whitehead, A. H., Jr.

1973-01-01

The anticipated growth of air transportation is in danger of being constrained by increased prices and insecure sources of petroleum-based fuel. Fuel-conservation possibilities attainable through the application of advances in aeronautical technology to aircraft design are identified with the intent of stimulating NASA R and T and systems-study activities in the various disciplinary areas. The material includes drag reduction; weight reduction; increased efficiency of main and auxiliary power systems; unconventional air transport of cargo; and operational changes.

Copper-Catalyzed, Directing Group-Assisted Fluorination of Arene and Heteroarene C-H Bonds

PubMed Central

Truong, Thanh; Klimovica, Kristine; Daugulis, Olafs

2013-01-01

We have developed a method for direct, copper-catalyzed, auxiliary-assisted fluorination of β-sp2 C-H bonds of benzoic acid derivatives and γ-sp2 C-H bonds of α,α-disubstituted benzylamine derivatives. The reaction employs CuI catalyst, AgF fluoride source, and DMF, pyridine, or DMPU solvent at moderately elevated temperatures. Selective mono- or difluorination can be achieved by simply changing reaction conditions. The method shows excellent functional group tolerance and provides a straightforward way for the preparation of ortho-fluorinated benzoic acids. PMID:23758609

Detection of multiple enteric virus strains within a foodborne outbreak of gastroenteritis: an indication of the source of contamination.

PubMed Central

Gallimore, C. I.; Pipkin, C.; Shrimpton, H.; Green, A. D.; Pickford, Y.; McCartney, C.; Sutherland, G.; Brown, D. W. G.; Gray, J. J.

2005-01-01

An outbreak of acute gastroenteritis of suspected viral aetiology occurred in April 2003 in the British Royal Fleet Auxiliary ship (RFA) Argus deployed in the Northern Arabian Gulf. There were 37 cases amongst a crew of 400 personnel. Of 13 samples examined from cases amongst the crew, six enteric viruses were detected by reverse transcriptase polymerase chain reaction (RT-PCR). Five different viruses were identified including, three norovirus genotypes, a sapovirus and a rotavirus. No multiple infections were detected. A common food source was implicated in the outbreak and epidemiological analysis showed a statistically significant association with salad as the source of the outbreak, with a relative risk of 3.41 (95% confidence interval of 1.7-6.81) of eating salad on a particular date prior to the onset of symptoms. Faecal contamination of the salad at source was the most probable explanation for the diversity of viruses detected and characterized. PMID:15724709

Gaseous Nitrogen Orifice Mass Flow Calculator

NASA Technical Reports Server (NTRS)

Ritrivi, Charles

2013-01-01

The Gaseous Nitrogen (GN2) Orifice Mass Flow Calculator was used to determine Space Shuttle Orbiter Water Spray Boiler (WSB) GN2 high-pressure tank source depletion rates for various leak scenarios, and the ability of the GN2 consumables to support cooling of Auxiliary Power Unit (APU) lubrication during entry. The data was used to support flight rationale concerning loss of an orbiter APU/hydraulic system and mission work-arounds. The GN2 mass flow-rate calculator standardizes a method for rapid assessment of GN2 mass flow through various orifice sizes for various discharge coefficients, delta pressures, and temperatures. The calculator utilizes a 0.9-lb (0.4 kg) GN2 source regulated to 40 psia (.276 kPa). These parameters correspond to the Space Shuttle WSB GN2 Source and Water Tank Bellows, but can be changed in the spreadsheet to accommodate any system parameters. The calculator can be used to analyze a leak source, leak rate, gas consumables depletion time, and puncture diameter that simulates the measured GN2 system pressure drop.

Advanced receptor modelling for the apportionment of road dust resuspension to atmospheric PM

NASA Astrophysics Data System (ADS)

Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

2009-04-01

Fugitive emissions from traffic resuspension can often represent an important source of atmospheric particulate matter in urban environments, especially when the scarce precipitations favour the accumulation of road dust. Resuspension of road dust can lead to high exposures to heavy metals, metalloids and mineral matter. Knowing the amount of its contribution to atmospheric PM is a key task for establishing eventual mitigation or preventive measures. Factor analysis techniques are widely used tools for atmospheric aerosol source apportionment, based on the mass conservation principle. Paatero and Tapper (1993) suggested the use of a Weighted Least Squares scheme with the aim of obtaining a minimum variance solution. Additionally they proposed to incorporate the basic physical constraint of non negativity, calling their approach Positive Matrix Factorization (PMF), which can be performed by the program PMF2 released by Paatero (1997). Nevertheless, Positive Matrix Factorization can be either solved with the Multilinear Engine (ME-2), a more flexible program, also developed by Paatero (1999), which can solve any model consisting in sum of products of unknowns. The main difference with PMF2 is that ME-2 does not solve only well-defined tasks, but its actions are defined in a "script file" written in a special-purpose programming language, allowing incorporating additional tasks such as data processing etc. Thus in ME-2 a priori information, e.g. chemical fingerprints can be included as auxiliary terms of the object function to be minimized. This feature of ME-2 make it especially suitable for source apportionment studies where some knowledge (chemical ratios, profiles, mass conservation etc) of involved sources is available. The aim of this study was to quantify the contribution of road dust resuspension in PM10, PM2.5 and PM1 data set from Barcelona (Spain). Given that recently the emission profile of local road dust was characterized (Amato et al., in press), authors show how to apply in ME-2 this knowledge to obtain a quantitative assessment of this source. The achievement of this objective permitted to show how is possible to improve a basic solution of PMF2 basing on an extended model. Results show that road dust resuspension accounted for 6.7 µg/m3 (16%) in PM10, 2.2 µg/m3 (8%) of PM2.5 and 0.3 µg/m3 (1%) of PM1, revealing that fugitive emissions were responsible of the 36%, 18% and 2% of total traffic emissions respectively in PM10, PM2.5 and PM1. Acknowledments: This work was funded by the Spanish Ministry of Science and Innovation (GRACCIE-SCD2007-00067)

Using Combination of Planar and Height Features for Detecting Built-Up Areas from High-Resolution Stereo Imagery

NASA Astrophysics Data System (ADS)

Peng, F.; Cai, X.; Tan, W.

2017-09-01

Within-class spectral variation and between-class spectral confusion in remotely sensed imagery degrades the performance of built-up area detection when using planar texture, shape, and spectral features. Terrain slope and building height are often used to optimize the results, but extracted from auxiliary data (e.g. LIDAR data, DSM). Moreover, the auxiliary data must be acquired around the same time as image acquisition. Otherwise, built-up area detection accuracy is affected. Stereo imagery incorporates both planar and height information unlike single remotely sensed images. Stereo imagery acquired by many satellites (e.g. Worldview-4, Pleiades-HR, ALOS-PRISM, and ZY-3) can be used as data source of identifying built-up areas. A new method of identifying high-accuracy built-up areas from stereo imagery is achieved by using a combination of planar and height features. The digital surface model (DSM) and digital orthophoto map (DOM) are first generated from stereo images. Then, height values of above-ground objects (e.g. buildings) are calculated from the DSM, and used to obtain raw built-up areas. Other raw built-up areas are obtained from the DOM using Pantex and Gabor, respectively. Final high-accuracy built-up area results are achieved from these raw built-up areas using the decision level fusion. Experimental results show that accurate built-up areas can be achieved from stereo imagery. The height information used in the proposed method is derived from stereo imagery itself, with no need to require auxiliary height data (e.g. LIDAR data). The proposed method is suitable for spaceborne and airborne stereo pairs and triplets.

E-Collaboration for Earth Observation (E-CEO) with the example of Contest #3 that focuses on the Atmospheric Correction of Ocean Colour data

NASA Astrophysics Data System (ADS)

Lavender, Samantha; Brito, Fabrice; Aas, Christina; Casu, Francesco; Ribeiro, Rita; Farres, Jordi

2014-05-01

Data challenges are becoming the new method to promote innovation within data-intensive applications; building or evolving user communities and potentially developing sustainable commercial services. These can utilise the vast amount of information (both in scope and volume) that's available online, and profits from reduced processing costs. Data Challenges are also closely related to the recent paradigm shift towards e-Science, also referred to as "data-intensive science'. The E-CEO project aims to deliver a collaborative platform that, through Data Challenge Contests, will improve the adoption and outreach of new applications and methods to processes Earth Observation (EO) data. Underneath, the backbone must be a common environment where the applications can be developed, deployed and executed. Then, the results need to be easily published in a common visualization platform for their effective validation, evaluation and transparent peer comparisons. Contest #3 is based around the atmospheric correction (AC) of ocean colour data with a particular focus on the use of auxiliary data files for processing Level 1 (Top of Atmosphere, TOA, calibrated radiances/reflectances) to Level 2 products (Bottom of Atmosphere, BOA, calibrated radiances/reflectance and derived products). Scientific researchers commonly accept the auxiliary inputs that they've been provided with and/or use the climatological data that accompanies the processing software; often because it can be difficult to obtain multiple data sources and convert them into a format the software accepts. Therefore, it's proposed to compare various ocean colour AC approaches and in the process study the uncertainties associated with using different meteorological auxiliary products for the processing of Medium Resolution Imaging Spectrometer (MERIS) i.e. the sensitivity of different atmospheric correction input assumptions.

Lack of high-quality studies comparing the effectiveness, and cost-effectiveness, of dental auxiliaries and dentists in performing dental care.

PubMed

Richards, Derek

2014-09-01

Cochrane Effective Practice and Organisation of Care (EPOC) Group's Specialised Register; Cochrane Oral Health Group's Specialised Register; the Cochrane Central Register of Controlled Trials Medline; Embase; CINAHL; Cochrane Database of Systematic Reviews; Database of Abstracts of Reviews of Effectiveness; five other databases and two trial registries. A number of dental journals were hand-searched and a grey literature search preformed. Randomised controlled trials (RCTs), non-randomised controlled trials (NRCTs), controlled before and after studies (CBAs) and interrupted time series (ITSs) were considered. Selection was conducted independently by two reviewers. Three reviewers extracted data and assessed risk of bias. Meta-analysis was not possible so a narrative summary was presented. Five studies (one cluster RCT, three RCTs and one NRCT) were included. All the studies were at high risk of bias and the overall quality of evidence was very low. The majority of the studies were more than 20 years old.Four studies evaluated sealant placement; three found no evidence of a difference in retention rates of those placed by dental auxiliaries and dentists over a range of follow-up periods (six to 24 months). One study found that sealants placed by a dental auxiliary had lower retention rates than ones placed by a dentist after 48 months (9.0% with auxiliary versus 29.1% with dentist); but the net reduction in the number of teeth exhibiting caries was lower for teeth treated by the dental auxiliary than the dentist (three with auxiliary versus 60 with dentist, P value < 0.001). One study showed no evidence of a difference in dental decay after treatment with fissure sealants between groups. One study comparing the effectiveness of dental auxiliaries and dentists performing ART reported no difference in survival rates of the restorations (fillings) after 12 months. We only identified five studies for inclusion in this review, all of which were at high risk of bias, and four were published more than 20 years ago, highlighting the paucity of high-quality evaluations of the relative effectiveness, cost-effectiveness and safety of dental auxiliaries compared with dentists in performing clinical tasks. No firm conclusions could be drawn from the present review about the relative effectiveness of dental auxiliaries and dentists.

The rural market: a unique communication medium.

PubMed

Spain, P

1992-01-01

In January 1990, the Health Secretary asked the Technologies for Primary Health Care (PRITECH) project to facilitate access to the many small villages with 500 people in Mexico since PRITECH had assisted the diarrhea disease control program. 1st PRITECH had Ministry of Health staff train trainers which would eventually spread the information to the rural areas. This strategy was effective only for those people who did not live in remote areas. The same reasons for remote people being at high risk of disease also limited this strategy: isolation, lack of education, limited diets, lack of access to services, and limited fluency in Spanish. PRITECH hired a local consulting organization, CICLOPE, to develop a new strategy. CICLOPE limited its activities to the states of Hidalgo and Vera Cruz for 8 months. 1st CICLOPE staff provided proper diarrhea management training including emphasis on oral rehydration therapy (ORT) to rural health auxiliaries. They used a gourd painted to look like an infant with holes and other modifications to depict the workings and results of diarrheal dehydration. The staff then sent the auxiliaries to their own communities to use the gourd dolls to teach mothers about ORT and correct diarrhea management. The staff conducted follow-up activities to monitor the auxiliaries' progress. This training approach allowed the auxiliaries to realize the abilities of the mothers and their active role in learning. The auxiliaries conducted the training at markets where women living in remote areas came weekly. The local radio announced market day events in which the auxiliaries participated and aired dramas about diarrhea management. CICLOPE staff and the auxiliaries sat up a booth at these markets to promote proper diarrhea management. They used a flip chart, comic books, a lottery game, and entertainment to impart education messages.

Awareness of biomedical waste management among dental professionals and auxiliary staff in Amritsar, India.

PubMed

Narang, Ramandeep S; Manchanda, Adesh; Singh, Simarpreet; Verma, Nitin; Padda, Sarfaraz

2012-12-01

The aim of this study was to determine awareness of biomedical waste (BMW) management policies and practices among dental professionals and auxiliary staff in a dental hospital/clinics in Amritsar, India, to inform the development of future policies for effective implementation of BMW rules. The study involved 160 staff members at the Amritsar hospital/clinics (80 dentists and 80 auxiliary staff) to whom a questionnaire was distributed regarding policies, practices and awareness relating to BMW. The questionnaire was first piloted. Completed questionnaires were returned anonymously. The resulting data were statistically tested using the chi-square test for differences between the dentists and auxiliary staff. In respect of BMW management policies, there was a highly significant difference in the responses of the dentists, whose answers suggested far greater knowledge than that of the auxiliaries (P<0.001). Regarding BMW management practices, the dentists were significantly more aware (P<0.001) of the method of waste collection in the hospital and the disposal of various items into different colour-coded bags. As for employee education/awareness, there was a significant difference (P<0.05) between the dentists and the auxiliaries on the question regarding records of BMW maintained in the hospital and the other responses to questions on these topics had a highly significant (P<0.001) difference between the two groups in favour of the dentists. The results of this study have demonstrated a lack of awareness of most aspects of BMW management among dental auxiliary staff in the dental hospital/clinics in Amritsar and a lack of awareness of some aspects among dentists who work in the hospital/clinics. The results provide the hospital authorities with data upon which they can develop a strategy for improving BMW management.

Heater-mixer for stored fluids

NASA Technical Reports Server (NTRS)

Canning, T. N. (Inventor)

1974-01-01

A fluid storage vessel for containing cryogenic fluids is described. The storage vessel contains an auxiliary chamber which is connected to the main container by a jet nozzle. The wall of the auxiliary vessel is heat cycled to produce a corresponding expansion and contraction of the fluid within the auxiliary chamber. This action causes heating and mixing of the stored fluid by means of jetting the expanded fluid to and from relative to the stored fluid contents of the vessel.

Permanent split capacitor single phase electric motor system

DOEpatents

Kirschbaum, H.S.

1984-08-14

A permanent split capacitor single phase electric motor achieves balanced operation at more than one operating point by adjusting the voltage supplied to the main and auxiliary windings and adjusting the capacitance in the auxiliary winding circuit. An intermediate voltage tap on an autotransformer supplies voltage to the main winding for low speed operation while a capacitive voltage divider is used to adjust the voltage supplied to the auxiliary winding for low speed operation. 4 figs.

SEPP-ZVS High Frequency Inverter Incorporating Auxiliary Switch

NASA Astrophysics Data System (ADS)

Ogiwara, Hiroyuki; Itoi, Misao; Nakaoka, Mutsuo

This paper presents a novel circuit topology to attain ZVS operation of a high frequency inverter over a wide range output power regulation using a PWM control technique by connecting an auxiliary switch to the conventional single ended push-pull (SEPP) ZVS high frequency inverter. A switching current is injected into the main switches via the auxiliary switch only during the short period between its turn-on and off times to supply a current required for its ZVS operation.

Environmental practices of the auxiliary companies to the Spanish automobile industry

NASA Astrophysics Data System (ADS)

González-Torre, Pilar L.; González, Beatriz A.; Gupta, Surendra M.

2005-11-01

The automobile manufacturing industry plays a very important role in a country's economy. The importance of automobile manufacturing industry lies in its sheer size and complexity in terms of the direct and indirect influence it commands across many other industries. While millions of people are employed in the automobile manufacturing industry, it is estimated that more than two and half times that number are employed in the auxiliary companies that supply parts to the automobile manufacturing companies. The auxiliary companies represent a group of businesses of various sizes, types, and geographical locations, producing a vast variety of products ranging from the very simple to the extremely intricate. In this study, the current environmental practices of management in the core Spanish auxiliary companies that do business with the automobile manufacturing industry (and thus form a large part of the automobile manufacturing industry's supply chain) are investigated. We show that while automobile manufacturing companies are under scrutiny to become more and more environmentally friendly, not only at their manufacturing stage but also at their products' useful and EOL stages, there appears to be no such burden on the auxiliary companies. Our conclusion is based on an elaborate survey conducted during the fall of 2004 of Spanish auxiliary companies with questions about the characteristics, environmental practices and reverse logistics related activities carried out by the companies.

Ejector Noise Suppression with Auxiliary Jet Injection

NASA Technical Reports Server (NTRS)

Berman, Charles H.; Andersen, Otto P., Jr.

1997-01-01

An experimental program to reduce aircraft jet turbulence noise investigated the interaction of small auxiliary jets with a larger main jet. Significant reductions in the far field jet noise were obtained over a range of auxiliary jet pressures and flow rates when used in conjunction with an acoustically lined ejector. While the concept is similar to that of conventional ejector suppressors that use mechanical mixing devices, the present approach should improve thrust and lead to lower weight and less complex noise suppression systems since no hardware needs to be located in the main jet flow. A variety of auxiliary jet and ejector configurations and operating conditions were studied. The best conditions tested produced peak to peak noise reductions ranging from 11 to 16 dB, depending on measurement angle, for auxiliary jet mass flows that were 6.6% of the main jet flow with ejectors that were 8 times the main jet diameter in length. Much larger reductions in noise were found at the original peak frequencies of the unsuppressed jet over a range of far field measurement angles.

Auxiliary basis expansions for large-scale electronic structure calculations.

PubMed

Jung, Yousung; Sodt, Alex; Gill, Peter M W; Head-Gordon, Martin

2005-05-10

One way to reduce the computational cost of electronic structure calculations is to use auxiliary basis expansions to approximate four-center integrals in terms of two- and three-center integrals, usually by using the variationally optimum Coulomb metric to determine the expansion coefficients. However, the long-range decay behavior of the auxiliary basis expansion coefficients has not been characterized. We find that this decay can be surprisingly slow. Numerical experiments on linear alkanes and a toy model both show that the decay can be as slow as 1/r in the distance between the auxiliary function and the fitted charge distribution. The Coulomb metric fitting equations also involve divergent matrix elements for extended systems treated with periodic boundary conditions. An attenuated Coulomb metric that is short-range can eliminate these oddities without substantially degrading calculated relative energies. The sparsity of the fit coefficients is assessed on simple hydrocarbon molecules and shows quite early onset of linear growth in the number of significant coefficients with system size using the attenuated Coulomb metric. Hence it is possible to design linear scaling auxiliary basis methods without additional approximations to treat large systems.

47 CFR 97.201 - Auxiliary station.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Technician, Technician Plus, General, Advanced or Amateur Extra Class operator license may be an auxiliary station. A holder of a Technician, Technician Plus, General, Advanced or Amateur Extra Class operator...

The Aerodynamic Characteristics of a Slotted Clark Y Wing as Affected by the Auxiliary Airfoil Position

NASA Technical Reports Server (NTRS)

Wenzinger, Carl J; Shortal, Joseph A

1932-01-01

Aerodynamic force tests on a slotted Clark Y wing were conducted in a vertical wind tunnel to determine the best position for a given auxiliary airfoil with respect to the main wing. A systematic series of 100 changes in location of the auxiliary airfoil were made to cover all the probable useful ranges of slot gap, slot width, and slot depth. The results of the investigation may be applied to the design of automatic or controlled slots on wings with geometric characteristics similar to the wing tested. The best positions of the auxiliary airfoil were covered by the range of the tests, and the position for desired aerodynamic characteristics may easily be obtained from charts prepared especially for the purpose.

Dynamic modelling and response characteristics of a magnetic bearing rotor system with auxiliary bearings

NASA Technical Reports Server (NTRS)

Free, April M.; Flowers, George T.; Trent, Victor S.

1995-01-01

Auxiliary bearings are a critical feature of any magnetic bearing system. They protect the soft iron core of the magnetic bearing during an overload or failure. An auxiliary bearing typically consists of a rolling element bearing or bushing with a clearance gap between the rotor and the inner race of the support. The dynamics of such systems can be quite complex. It is desired to develop a rotordynamic model which describes the dynamic behavior of a flexible rotor system with magnetic bearings including auxiliary bearings. The model is based upon an experimental test facility. Some simulation studies are presented to illustrate the behavior of the model. In particular, the effects of introducing sideloading from the magnetic bearing when one coil fails is studied.

47 CFR 74.1 - Scope.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Stations, Subpart E; TV Auxiliary Broadcast Stations, Subpart F; Low-power TV, TV Translator and TV Booster Stations, Subpart G; Low-power Auxiliary Stations, Subpart H; FM Broadcast Translator Stations and FM...

Evaluation of auxiliary power subsystems for gas engine heat pumps, phase 2

NASA Astrophysics Data System (ADS)

Rasmussen, R. W.; Wahlstedt, D. A.; Planer, N.; Fink, J.; Persson, E.

1988-12-01

The need to determine the practical, technical and economic viability for a stand-alone Gas Engine Heat Pump (GEHP) system capable of generating its own needed electricity is addressed. Thirty-eight reasonable design configurations were conceived based upon small-sized power conversion equipment that is either commercially available or close to emerging on the market. Nine of these configurations were analyzed due to their potential for low first cost, high conversion efficiency, availability or simplicity. It was found that electric consumption can be reduced by over 60 percent through the implementation of high efficiency, brushless, permanent magnet motors as fan and pump drivers. Of the nine selected configurations employing variable-speed fans, two were found to have simple incremental payback periods of 4.2 to 16 years, depending on the U.S. city chosen for analysis. Although the auxiliary power subsystem option is only marginally attractive from an economic standpoint, the increased gas load provided to the local gas utility may be sufficient to encourage further development. The ability of the system to operate completely disconnected from the electric power source may be a feature of high merit.

3-D Forward modeling of Induced Polarization Effects of Transient Electromagnetic Method

NASA Astrophysics Data System (ADS)

Wu, Y.; Ji, Y.; Guan, S.; Li, D.; Wang, A.

2017-12-01

In transient electromagnetic (TEM) detection, Induced polarization (IP) effects are so important that they cannot be ignored. The authors simulate the three-dimensional (3-D) induced polarization effects in time-domain directly by applying the finite-difference time-domain method (FDTD) based on Cole-Cole model. Due to the frequency dispersion characteristics of the electrical conductivity, the computations of convolution in the generalized Ohm's law of fractional order system makes the forward modeling particularly complicated. Firstly, we propose a method to approximate the fractional order function of Cole-Cole model using a lower order rational transfer function based on error minimum theory in the frequency domain. In this section, two auxiliary variables are introduced to transform nonlinear least square fitting problem of the fractional order system into a linear programming problem, thus avoiding having to solve a system of equations and nonlinear problems. Secondly, the time-domain expression of Cole-Cole model is obtained by using Inverse Laplace transform. Then, for the calculation of Ohm's law, we propose an e-index auxiliary equation of conductivity to transform the convolution to non-convolution integral; in this section, the trapezoid rule is applied to compute the integral. We then substitute the recursion equation into Maxwell's equations to derive the iterative equations of electromagnetic field using the FDTD method. Finally, we finish the stimulation of 3-D model and evaluate polarization parameters. The results are compared with those obtained from the digital filtering solution of the analytical equation in the homogeneous half space, as well as with the 3-D model results from the auxiliary ordinary differential equation method (ADE). Good agreements are obtained across the three methods. In terms of the 3-D model, the proposed method has higher efficiency and lower memory requirements as execution times and memory usage were reduced by 20% compared with ADE method.

Logistics and Capability Implications of a Bradley Fighting Vehicle with a Fuel Cell Auxiliary Power Unit

DTIC Science & Technology

2003-10-13

04ANNUAL-524 Logistics and Capability Implications of a Bradley Fighting Vehicle with a Fuel Cell Auxiliary Power Unit Joseph Conover, Harry...used or the main engines are restarted. Integration of a solid oxide fuel cell (SOFC) auxiliary power unit into a military vehicle has the...presented which show the fuel usage and capability impacts of incorporating a fuel cell APU into the electrical system of a Bradley M2A3 Diesel

[Evaluating work intensity in major and auxiliary occupations of by-product coke industry].

PubMed

Smagulov, N K; Alpysbayeva, Zh T

2015-01-01

The article covers evaluation of work strain in major and auxiliary occupations of by-product coke industry. The study results conclude that occupational activity of by-product coke industry workers, under exposure to occupational hazards, affects the workers' performance. Major occupations workers demonstrate higher level of functional strain of CNS, poor concentration of attention and lower ability to switch over, decreased general performance, vs. the auxiliary occupations workers who demonstrated increased cardiovascular and neuro-muscular strain due to occupational activity.

Novel zero voltage transition pulse width modulation flyback converter

NASA Astrophysics Data System (ADS)

Adib, Ehsan; Farzanehfard, Hosein

2010-09-01

In this article, a new zero voltage (ZV) transition flyback converter is introduced which uses a simple auxiliary circuit. In this converter, ZV switching condition is achieved for the converter switch while zero current switching condition is attained for the auxiliary switch. There is no additional voltage and current stress on the main switch. Main diode, auxiliary circuit voltage and current ratings are low. The proposed converter is analysed and design procedure is discussed. The presented experimental results of a prototype converter justify the theoretical analysis.

Health Physics Innovations Developed During Cassini for Future Space Applications

NASA Technical Reports Server (NTRS)

Nickell, Rodney E.; Rutherford, Theresa M.; Marmaro, George M.

1999-01-01

The long history of space flight includes missions that used Space Nuclear Auxiliary Power devices, starting with the Transit 4A Spacecraft (1961), continuing through the Apollo, Pioneer, Viking, Voyager, Galileo, Ulysses, Mars Pathfinder, and most recently, Cassini (1997). All Major Radiological Source (MRS) missions were processed at Kennedy Space Center/Cape Canaveral Air Station (KSC/CCAS) Launch Site in full compliance with program and regulatory requirements. The cumulative experience gained supporting these past missions has led to significant innovations which will be useful for benchmarking future MRS mission ground processing. Innovations developed during ground support for the Cassini mission include official declaration of sealed-source classifications, utilization of a mobile analytical laboratory, employment of a computerized dosimetry record management system, and cross-utilization of personnel from related disciplines.

A method to calibrate phase fluctuation in polarization-sensitive swept-source optical coherence tomography

NASA Astrophysics Data System (ADS)

Lu, Zenghai; Kasaragod, Deepa K.; Matcher, Stephen J.

2011-06-01

A phase fluctuation calibration method is presented for polarization-sensitive swept-source optical coherence tomography (PS-SS-OCT) using continuous polarization modulation. The method consists of the generation of a continuous triggered tone-burst waveform rather than an asynchronous waveform by use of a function generator and the removal of the global phases of the measured Jones matrices by use of matrix normalization. This could remove the use of auxiliary optical components for the phase fluctuation compensation in the system, which reduces the system complexity. Phase fluctuation calibration is necessary to obtain the reference Jones matrix by averaging the measured Jones matrices at sample surfaces. Measurements on an equine tendon sample were made by the PS-SS-OCT system to validate the proposed method.

Improved control strategy for wind-powered refrigerated storage of apples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldwin, J.D.C.

1979-01-01

The need for an improved control strategy for the operation of a wind-powered refrigeration system for the storage of apples was investigated. The results are applicable to other systems which employ intermittently available power sources, battery and thermal storage, and an auxiliary, direct current power supply. Tests were conducted on the wind-powered refrigeration system at the Virginia Polytechnic Institute and State University Horticulture Research Farm in Blacksburg, Virginia. Tests were conducted on the individual components of the system. In situ windmill performance was also conducted. The results of these tests have been presented. An improved control strategy was developed tomore » improve the utilization of available wind energy and to reduce the need for electrical energy from an external source while maintaining an adequate apple storage environment.« less

Metabolic Engineering of Corynebacterium glutamicum for Methanol Metabolism

PubMed Central

Witthoff, Sabrina; Schmitz, Katja; Niedenführ, Sebastian; Nöh, Katharina; Noack, Stephan

2015-01-01

Methanol is already an important carbon feedstock in the chemical industry, but it has found only limited application in biotechnological production processes. This can be mostly attributed to the inability of most microbial platform organisms to utilize methanol as a carbon and energy source. With the aim to turn methanol into a suitable feedstock for microbial production processes, we engineered the industrially important but nonmethylotrophic bacterium Corynebacterium glutamicum toward the utilization of methanol as an auxiliary carbon source in a sugar-based medium. Initial oxidation of methanol to formaldehyde was achieved by heterologous expression of a methanol dehydrogenase from Bacillus methanolicus, whereas assimilation of formaldehyde was realized by implementing the two key enzymes of the ribulose monophosphate pathway of Bacillus subtilis: 3-hexulose-6-phosphate synthase and 6-phospho-3-hexuloisomerase. The recombinant C. glutamicum strain showed an average methanol consumption rate of 1.7 ± 0.3 mM/h (mean ± standard deviation) in a glucose-methanol medium, and the culture grew to a higher cell density than in medium without methanol. In addition, [13C]methanol-labeling experiments revealed labeling fractions of 3 to 10% in the m + 1 mass isotopomers of various intracellular metabolites. In the background of a C. glutamicum Δald ΔadhE mutant being strongly impaired in its ability to oxidize formaldehyde to CO2, the m + 1 labeling of these intermediates was increased (8 to 25%), pointing toward higher formaldehyde assimilation capabilities of this strain. The engineered C. glutamicum strains represent a promising starting point for the development of sugar-based biotechnological production processes using methanol as an auxiliary substrate. PMID:25595770

On the consistency of the Oppenheimer-Snyder solution for a dust star. Reply to Marshall's criticism

NASA Astrophysics Data System (ADS)

Zakir, Zahid

2018-02-01

The recent alternative to the Oppenheimer-Snyder (OS) solution for a dust star proposed by Marshall in the paper "Gravitational collapse without black holes" (Astrophys. Space Sci. 342:329, 2012) is analyzed. It is shown that this proposal leads to a non-diagonal metric, with which the Einstein equations become practically unsolvable. Any ansatz proposed as their exact solution turns out to be arbitrary and may be unlimited number of the such solutions. This is due to the fact that an auxiliary function y(R,r), introduced by OS as t=M(y), is unambiguously fixed by the diagonality condition and the matching on the surface, and thus in the non-diagonal case it remains arbitrary. It is also shown that the OS solution, as a description in terms of the Schwarzschild coordinates, leads to a frozen star (or frozar) picture not only for the surface, asymptotically freezing outside the gravitational radius, but for interior layers too which also freeze near their own asymptotes. At most of the inner region these asymptotes are located almost equidistantly and only for layers initially close to the surface they become denser. The reason for the such densifying is not "a gravitational repulsion", but their later freezing and higher spatial contractions, while they remain be uniform and free falling in the comoving frames.

Solving quantum optimal control problems using Clebsch variables and Lin constraints

NASA Astrophysics Data System (ADS)

Delgado-Téllez, M.; Ibort, A.; Rodríguez de la Peña, T.

2018-01-01

Clebsch variables (and Lin constraints) are applied to the study of a class of optimal control problems for affine-controlled quantum systems. The optimal control problem will be modelled with controls defined on an auxiliary space where the dynamical group of the system acts freely. The reciprocity between both theories: the classical theory defined by the objective functional and the quantum system, is established by using a suitable version of Lagrange’s multipliers theorem and a geometrical interpretation of the constraints of the system as defining a subspace of horizontal curves in an associated bundle. It is shown how the solutions of the variational problem defined by the objective functional determine solutions of the quantum problem. Then a new way of obtaining explicit solutions for a family of optimal control problems for affine-controlled quantum systems (finite or infinite dimensional) is obtained. One of its main advantages, is the the use of Clebsch variables allows to compute such solutions from solutions of invariant problems that can often be computed explicitly. This procedure can be presented as an algorithm that can be applied to a large class of systems. Finally, some simple examples, spin control, a simple quantum Hamiltonian with an ‘Elroy beanie’ type classical model and a controlled one-dimensional quantum harmonic oscillator, illustrating the main features of the theory, will be discussed.

72. VISITOR'S CENTER, MODEL OF BOILER CHAMBER, AUXILIARY CHAMBER, REACTOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

72. VISITOR'S CENTER, MODEL OF BOILER CHAMBER, AUXILIARY CHAMBER, REACTOR AND CANAL (LOCATION T) - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

16. DETAIL VIEW OF AUXILIARY LOCK MITER GATE OPERATING MACHINERY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. DETAIL VIEW OF AUXILIARY LOCK MITER GATE OPERATING MACHINERY LOCATED IN INTERMEDIATE WALL, LOOKING NORTHWEST - Upper Mississippi River 9-Foot Channel Project, Lock & Dam 27, Granite City, Madison County, IL

47 CFR 74.501 - Classes of aural broadcast auxiliary stations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... their co-owned FM booster stations, between noncommercial educational FM radio stations and their co... microwave booster station. A fixed station in the broadcast auxiliary service that receives and amplifies...

47 CFR 74.501 - Classes of aural broadcast auxiliary stations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... their co-owned FM booster stations, between noncommercial educational FM radio stations and their co... microwave booster station. A fixed station in the broadcast auxiliary service that receives and amplifies...

47 CFR 74.501 - Classes of aural broadcast auxiliary stations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... their co-owned FM booster stations, between noncommercial educational FM radio stations and their co... microwave booster station. A fixed station in the broadcast auxiliary service that receives and amplifies...