average blister diameter: Topics by Science.gov

Sample records for average blister diameter

Assessment of imperfect detection of blister rust in whitebark pine within the Greater Yellowstone Ecosystem

USGS Publications Warehouse

Wright, Wilson J.; Irvine, Kathryn M.

2017-01-01

We examined data on white pine blister rust (blister rust) collected during the monitoring of whitebark pine trees in the Greater Yellowstone Ecosystem (from 2004-2015). Summaries of repeat observations performed by multiple independent observers are reviewed and discussed. These summaries show variability among observers and the potential for errors being made in blister rust status. Based on this assessment, we utilized occupancy models to analyze blister rust prevalence while explicitly accounting for imperfect detection. Available covariates were used to model both the probability of a tree being infected with blister rust and the probability of an observer detecting the infection. The fitted model provided strong evidence that the probability of blister rust infection increases as tree diameter increases and decreases as site elevation increases. Most importantly, we found evidence of heterogeneity in detection probabilities related to tree size and average slope of a transect. These results suggested that detecting the presence of blister rust was more difficult in larger trees. Also, there was evidence that blister rust was easier to detect on transects located on steeper slopes. Our model accounted for potential impacts of observer experience on blister rust detection probabilities and also showed moderate variability among the different observers in their ability to detect blister rust. Based on these model results, we suggest that multiple observer sampling continue in future field seasons in order to allow blister rust prevalence estimates to be corrected for imperfect detection. We suggest that the multiple observer effort be spread out across many transects (instead of concentrated at a few each field season) while retaining the overall proportion of trees with multiple observers around 5-20%. Estimates of prevalence are confounded with detection unless it is explicitly accounted for in an analysis and we demonstrate how an occupancy model can be used to do account for this source of observation error.
Cracks and blisters formed close to a silicon wafer surface by He-H co-implantation at low energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cherkashin, N., E-mail: nikolay.cherkashin@cemes.fr; Darras, F.-X.; Claverie, A.

2015-12-28

We have studied the effect of reducing the implantation energy towards low keV values on the areal density of He and H atoms stored within populations of blister cavities formed by co-implantation of the same fluence of He then H ions into Si(001) wafers and annealing. Using a variety of experimental techniques, we have measured blister heights and depth from the surface, diameter, areal density of the cracks from which they originate as functions of implantation energy and fluence. We show that there is a direct correlation between the diameters of the cracks and the heights of the associated blisters.more » This correlation only depends on the implantation energy, i.e., only on the depth at which the cracks are located. Using finite element method modeling, we infer the pressure inside the blister cavities from the elastic deformations they generate, i.e., from the height of the blisters. From this, we demonstrate that the gas pressure within a blister only depends on the diameter of the associated crack and not on its depth position and derive an analytical expression relating these parameters. Relating the pressure inside a blister to the respective concentrations of gas molecules it contains, we deduce the areal densities of He and H atoms contained within the populations of blisters. After low-energy implantations (8 keV He{sup +}, 3 keV H{sup +}), all the implanted He and H atoms contribute to the formation of the blisters. There is no measurable exo-diffusion of any of the implanted gases, in contrast to what was assumed at the state of the art to explain the failure of the Smart-Cut technology when using very low energy ion implantation for the fabrication of ultra-thin layers. Alternative explanations must be investigated.« less
Origin of microplasma instabilities during DC operation of silicon based microhollow cathode devices

NASA Astrophysics Data System (ADS)

Felix, Valentin; Lefaucheux, Philippe; Aubry, Olivier; Golda, Judith; Schulz-von der Gathen, Volker; Overzet, Lawrence J.; Dussart, Rémi

2016-04-01

The failure mechanisms of micro hollow cathode discharges (MHCD) in silicon have been investigated using their I-V characteristics, high speed photography and scanning electron microscopy. Experiments were carried out in helium. We observed I-V instabilities in the form of rapid voltage decreases associated with current spikes. The current spikes can reach values more than 100 times greater than the average MHCD current. (The peaks can be more than 1 Ampere for a few 10’s of nanoseconds.) These current spikes are correlated in time with 3-10 μm diameter optical flashes that occur inside the cavities. The SEM characterizations indicated that blister-like structures form on the Si surface during plasma operation. Thin Si layers detach from the surface in localized regions. We theorize that shallow helium implantation occurs and forms the ‘blisters’ whenever the Si is biased as the cathode. These blisters ‘explode’ when the helium pressure inside them becomes too large leading to the transient micro-arcs seen in both the optical emission and the I-V characteristics. We noted that blisters were never found on the metal counter electrode, even when it was biased as the cathode (and the Si as the anode). This observation led to a few suggestions for delaying the failure of Si MHCDs. One may coat the Si cathode (cavities) with blister resistant material; design the MHCD array to operate with the Si as the anode rather than as the cathode; or use a gas additive to prevent surface damage. Regarding the latter, tests using SF6 as the gas additive successfully prevented blister formation through rapid etching. The result was an enhanced MHCD lifetime.
[Microsurgical anatomy importance of A1-anterior communicating artery complex].

PubMed

Monroy-Sosa, Alejandro; Pérez-Cruz, Julio César; Reyes-Soto, Gervith; Delgado-Hernández, Carlos; Macías-Duvignau, Mario Alberto; Delgado-Reyes, Luis

2013-01-01

The anterior cerebral artery originates from the bifurcation of the internal carotid artery lateral to the optic chiasm, then joins with its contralateral counterpart via the anterior communicating artery. A1-anterior communicating artery complex is the most frequent anatomical variants and is the major site of aneurysms between 30 to 37%. Know the anatomy microsurgical, variants anatomical and importance of complex precommunicating segment-artery anterior communicating in surgery neurological of the pathology vascular, mainly aneurysms, in Mexican population. The study was performed in 30 brains injected. Microanatomy was studied (length and diameter) of A1-anterior communicating artery complex and its variants. 60 segments A1, the average length of left side was 11.35 mm and 11.84 mm was right. The average diameter of left was 1.67 mm and the right was 1.64 mm. The average number of perforators on the left side was 7.9 and the right side was 7.5. Anterior communicating artery was found in 29 brains of the optic chiasm, its course depended on the length of the A1 segment. The average length of the segment was 2.84 mm, the average diameter was 1.41 mm and the average number of perforators was 3.27. A1-anterior communicating artery complex variants were found in 18 (60%) and the presence of two blister-like aneurysms. It is necessary to understand the A1-anterior communicating artery complex microanatomy of its variants to have a three-dimensional vision during aneurysm surgery.
Development of a Lightweight, High Strength, Collapsible Hose

DTIC Science & Technology

1989-02-01

they will erupt through the elastomer as the hose exits the extrusion head and result in blistering of the cover and/or the lining. The jacket is...not successful. Extreme blistering of the elastomer occurred as the hose exited the extrusion head. The conclusion was drawn that moisture was not...HIGH STRENGTH, COLLAPSIBLE HOSE ABSTRACT This report documents an exploratory development effort to produce a 6-inch diameter, lightweight, high strength
Creating nanostructures on silicon using ion blistering and electron beam lithography

NASA Astrophysics Data System (ADS)

Giguère, Alexandre; Beerens, Jean; Terreault, Bernard

2006-01-01

We have investigated the patterning of silicon surfaces using ion blistering in conjunction with e-beam lithography. Variable width (150-5000 nm) trenches were first written in 500 nm thick PMMA resist spin coated on silicon, using an electron beam. Next, 10 keV H2+ ions were implanted to various fluences through the masks. The resist was then removed and the samples were rapidly thermally annealed at 900 °C. The resulting surface morphologies were investigated by atomic force microscopy. In the wider trenches, round blisters with 600-900 nm diameter are observed, which are similar to those observed on unmasked surfaces. In submicron trenches, there is a transition in morphology, caused by the proximity to the border. The blisters are smaller and they are densely aligned along the trench direction ('string of pearls' pattern). Unusual blister geometries are observed in the narrowest trenches (150 nm) at higher H doses (>=1 × 1017 H cm-2)—such as tubular blisters aligned along the trench. It was also found that for H doses of >=6 × 1016 H cm-2 the surface swells uniformly, which has implications for the blistering mechanism. The prospects for accomplishing ion cutting, layer transfer and bonding of finely delineated patterns of silicon onto another material are discussed in the light of the above results.
Low average blister-rust infection rates may mean high control costs

Treesearch

Robert Marty

1965-01-01

The Northeastern Forest Experiment Station, in cooperation with Federal and State forest-pest-control agencies, undertook a survey of blister-rust infection rates in the white pine region of the East during 1962 and 1963. Those engaged in blister-rust-control activities will not be surprised at the survey's results. We found that infection rates were significantly...
Microstructural characterization of an irradiated RERTR-6 U-7Mo/AA4043 alloy dispersion fuel plate specimen blister-tested to a final temperature of 500°C

DOE PAGES

Keiser, Jr., Dennis D.; Jue, Jan -Fong; Gan, Jian; ...

2017-02-27

The Material Management and Minimization (M3) Reactor Conversion Program, in the past called the Reduced Enrichment for Research and Test Reactor (RERTR) Program, is developing low-enriched uranium (LEU) fuels for application in research reactors. U–Mo alloy dispersion fuel is one type being developed. Blister testing has been performed on different fuel plate samples to determine the margin to failure for fuel plates irradiated to different fission densities. Microstructural characterization was performed using scanning electron microscopy and transmission electron microscopy on a sample taken from a U-7Mo/AA4043 matrix dispersion fuel plate irradiated in the RERTR-6 experiment that was blister-tested up tomore » a final temperature of 500°C. The results indicated that two types of grain/cell boundaries were observed in the U- 7Mo fuel particles, one with a relatively low Mo content and fission gas bubbles and a second type enriched in Si, due to interdiffusion from the Si-containing matrix, with little evidence of fission gas bubbles. With respect to the behavior of the major fission gas Xe, a significant amount of the Xe was still observed within the U-7Mo fuel particle, along with microns into the AA4043 matrix. For the fuel/matrix interaction layers that form during fabrication and then grow during irradiation, they change from the as-irradiated amorphous structure to one that is crystalline after blister testing. In the AA4043 matrix, the original Si-rich precipitates, which are typically observed in as-irradiated U-Mo dispersion fuel, get consumed due to interdiffusion with the U-7Mo fuel particles during the blister test. Lastly, the fission gas bubbles that were originally around 2 nm in diameter and resided on a fission gas superlattice in the intragranular regions of as-irradiated U-7Mo fuel grew in size (up to ~20 nm diameter) during blister testing.« less
Microstructural characterization of an irradiated RERTR-6 U-7Mo/AA4043 alloy dispersion fuel plate specimen blister-tested to a final temperature of 500°C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keiser, Jr., Dennis D.; Jue, Jan -Fong; Gan, Jian

The Material Management and Minimization (M3) Reactor Conversion Program, in the past called the Reduced Enrichment for Research and Test Reactor (RERTR) Program, is developing low-enriched uranium (LEU) fuels for application in research reactors. U–Mo alloy dispersion fuel is one type being developed. Blister testing has been performed on different fuel plate samples to determine the margin to failure for fuel plates irradiated to different fission densities. Microstructural characterization was performed using scanning electron microscopy and transmission electron microscopy on a sample taken from a U-7Mo/AA4043 matrix dispersion fuel plate irradiated in the RERTR-6 experiment that was blister-tested up tomore » a final temperature of 500°C. The results indicated that two types of grain/cell boundaries were observed in the U- 7Mo fuel particles, one with a relatively low Mo content and fission gas bubbles and a second type enriched in Si, due to interdiffusion from the Si-containing matrix, with little evidence of fission gas bubbles. With respect to the behavior of the major fission gas Xe, a significant amount of the Xe was still observed within the U-7Mo fuel particle, along with microns into the AA4043 matrix. For the fuel/matrix interaction layers that form during fabrication and then grow during irradiation, they change from the as-irradiated amorphous structure to one that is crystalline after blister testing. In the AA4043 matrix, the original Si-rich precipitates, which are typically observed in as-irradiated U-Mo dispersion fuel, get consumed due to interdiffusion with the U-7Mo fuel particles during the blister test. Lastly, the fission gas bubbles that were originally around 2 nm in diameter and resided on a fission gas superlattice in the intragranular regions of as-irradiated U-7Mo fuel grew in size (up to ~20 nm diameter) during blister testing.« less
Microstructural characterization of an irradiated RERTR-6 U-7Mo/AA4043 alloy dispersion fuel plate specimen blister-tested to a final temperature of 500 °C

NASA Astrophysics Data System (ADS)

Keiser, Dennis D.; Jue, Jan-Fong; Gan, Jian; Miller, Brandon D.; Robinson, Adam B.; Madden, James W.; Ross Finlay, M.; Moore, Glenn; Medvedev, Pavel; Meyer, Mitch

2017-05-01

The Material Management and Minimization (M3) Reactor Conversion Program, in the past called the Reduced Enrichment for Research and Test Reactor (RERTR) Program, is developing low-enriched uranium (LEU) fuels for application in research and test reactors. U-Mo alloy dispersion fuel is one type being developed. Blister testing has been performed on different fuel plate samples to determine the margin to failure for fuel plates irradiated to different fission densities. Microstructural characterization was performed using scanning electron microscopy and transmission electron microscopy on a sample taken from a U-7Mo/AA4043 matrix dispersion fuel plate irradiated in the RERTR-6 experiment that was blister-tested up to a final temperature of 500 °C. The results indicated that two types of grain/cell boundaries were observed in the U-7Mo fuel particles, one with a relatively low Mo content and fission gas bubbles and a second type enriched in Si, due to interdiffusion from the Si-containing matrix, with little evidence of fission gas bubbles. With respect to the behavior of the major fission gas Xe, a significant amount of the Xe was still observed within the U-7Mo fuel particle, along with microns into the AA4043 matrix. For the fuel/matrix interaction layers that form during fabrication and then grow during irradiation, they change from the as-irradiated amorphous structure to one that is crystalline after blister testing. In the AA4043 matrix, the original Si-rich precipitates, which are typically observed in as-irradiated U-Mo dispersion fuel, get consumed due to interdiffusion with the U-7Mo fuel particles during the blister test. Finally, the fission gas bubbles that were originally around 3 nm in diameter and resided on a fission gas superlattice (FGS) in the intragranular regions of as-irradiated U-7Mo fuel grew in size (up to ∼20 nm diameter) during blister testing and, in many areas, are no longer organized as a superlattice.
Silicon patterning using ion blistering and e-beam lithography

NASA Astrophysics Data System (ADS)

Giguere, A.; Terreault, B.; Beerens, J.; Aimez, V.; Beauvais, J.

2004-03-01

We explore the limits of silicon patterning using ion blistering in conjunction with e-beam lithography. In a first approach, we implanted 3.5E16 H/cm**2 at 5 keV through variable width (0.1-10 micron) e-beam written PMMA masks. The resist was then removed and the samples were rapid-thermal-annealed (RTA) up to 650 °C. In the wider trenches, round blisters with 800-900 nm diameter and 15 nm height and a few exfoliations are observed, which are similar to those observed on an unmasked surface. In submicron trenches (500-1000 nm), there is a transition in morphology created by the proximity to the border; the blisters are smaller and they are densely aligned along the trench direction ("pearl-string" pattern). No effect is observed in the lowest dimension trenches. The results are discussed in terms of stress/strain fields, defect configuration, and mask shadowing and charging effects. Ultimate pattern resolution will be limited by lateral straggling of the ions in and by the mechanics of lateral crack propagation.
An ecosystem-scale model for the spread of a host-specific forest pathogen in the Greater Yellowstone Ecosystem

USGS Publications Warehouse

Hatala, J.A.; Dietze, M.C.; Crabtree, R.L.; Kendall, Katherine C.; Six, D.; Moorcroft, P.R.

2011-01-01

The introduction of nonnative pathogens is altering the scale, magnitude, and persistence of forest disturbance regimes in the western United States. In the high-altitude whitebark pine (Pinus albicaulis) forests of the Greater Yellowstone Ecosystem (GYE), white pine blister rust (Cronartium ribicola) is an introduced fungal pathogen that is now the principal cause of tree mortality in many locations. Although blister rust eradication has failed in the past, there is nonetheless substantial interest in monitoring the disease and its rate of progression in order to predict the future impact of forest disturbances within this critical ecosystem.This study integrates data from five different field-monitoring campaigns from 1968 to 2008 to create a blister rust infection model for sites located throughout the GYE. Our model parameterizes the past rates of blister rust spread in order to project its future impact on high-altitude whitebark pine forests. Because the process of blister rust infection and mortality of individuals occurs over the time frame of many years, the model in this paper operates on a yearly time step and defines a series of whitebark pine infection classes: susceptible, slightly infected, moderately infected, and dead. In our analysis, we evaluate four different infection models that compare local vs. global density dependence on the dynamics of blister rust infection. We compare models in which blister rust infection is: (1) independent of the density of infected trees, (2) locally density-dependent, (3) locally density-dependent with a static global infection rate among all sites, and (4) both locally and globally density-dependent. Model evaluation through the predictive loss criterion for Bayesian analysis supports the model that is both locally and globally density-dependent. Using this best-fit model, we predicted the average residence times for the four stages of blister rust infection in our model, and we found that, on average, whitebark pine trees within the GYE remain susceptible for 6.7 years, take 10.9 years to transition from slightly infected to moderately infected, and take 9.4 years to transition from moderately infected to dead. Using our best-fit model, we project the future levels of blister rust infestation in the GYE at critical sites over the next 20 years.
A method for estimating white pine blister rust canker age on limber pine in the central Rocky Mountains

Treesearch

Holly S. J. Kearns; William R. Jacobi; Brian W. Geils

2009-01-01

Epidemiological studies of white pine blister rust on limber pine require a temporal component to explain variations in incidence of infection and mortality. Unfortunately, it is not known how long the pathogen has been present at various sites in the central Rocky Mountains of North America. Canker age, computed from canker length and average expansion rate, can be...
7 CFR 51.1319 - Injury.

Code of Federal Regulations, 2013 CFR

2013-01-01

...-fourths inch in diameter. 2 (2) Hail marks or other similar depressions or scars which are not very...) Cork spot when a pear shows depressions or the flesh of the pear is more than slightly affected. (4... depressions, or any stings which materially affect the general appearance of the fruit. (6) Blister mite or...
7 CFR 51.1319 - Injury.

Code of Federal Regulations, 2014 CFR

2014-01-01

...-fourths inch in diameter. 2 (2) Hail marks or other similar depressions or scars which are not very...) Cork spot when a pear shows depressions or the flesh of the pear is more than slightly affected. (4... depressions, or any stings which materially affect the general appearance of the fruit. (6) Blister mite or...
Helium trapping in aluminium near the critical dose on blister formation

NASA Astrophysics Data System (ADS)

Fukahori, T.; Kanda, Y.; Mori, K.; Tobimatsu, H.

1985-08-01

Blistering and flaking caused by energetic He ions emitted from the plasma in fusion reactors possibly contribute to first-wall erosion. In order to study their characteristics, the numbers of He atoms trapped in He-ion-irradiated Al samples have been measured by a He atom measurement system and every sample has been observed by a scanning electron microscope. The samples have been prepared from a polycrystalline plate and irradiated with 20 keV He ions at room temperature. The saw-tooth like variation of the trapped He atoms with the dose has three edges corresponding to the blistering, flaking and double flaking, respectively. The critical doses for the three events are found to be 4 × 10 21, 7 × 10 21, 12 × 10 21 He atoms m -2, respectively. The average number of He atoms included in an event is 5.4 × 10 10 He atoms in the case of the blistering and 2.1 × 10 11 He atoms in the case of flaking.
A bottom-up approach for controlled deformation of carbon nanotubes through blistering of supporting substrate surface.

PubMed

Prudkovskiy, Vladimir; Iacovella, Fabrice; Katin, Konstantin P; Maslov, Mikhail M; Cherkashin, Nikolay

2018-06-13

Tuning the band structure and, in particular, gap opening in 1D and 2D materials through their deformation is a promising approach for their application in modern semiconductor devices. However, there is an essential breach between existing laboratory scale methods applied for deformation of low-dimensional materials and the needs of large-scale production. In this work, we propose a novel method which is potentially well compatible with high end technological application: single-walled carbon nanotubes (SWCNTs) first deposited on the flat surface of a supporting wafer, which has been pre-implanted with H+ and He+ ions, are deformed in a controlled and repetitive manner over blisters formed after subsequent thermal annealing. By using resonant Raman spectroscopy, we demonstrate that the SWCNTs clamped by metallic stripes at their ends are deformed over blisters to an average tensile strain of 0.15 ± 0.03 %, which is found to be in a good agreement with the value calculated taking into account blister's dimensions. The principle of the technique may be applied to other 1D and 2D materials in perspective. © 2018 IOP Publishing Ltd.
A prospective randomised study comparing the jubilee dressing method to a standard adhesive dressing for total hip and knee replacements.

PubMed

Burke, Neil G; Green, Connor; McHugh, Gavin; McGolderick, Niall; Kilcoyne, Carol; Kenny, Patrick

2012-08-01

It is important to reduce potential wound complications in total hip and total knee arthroplasty procedures. The purpose of this study was to compare the jubilee dressing method to a standard adhesive dressing. 124 patients (62 total hip replacements and 62 total knee replacements) were randomly selected to have either a standard adhesive dressing or jubilee method dressing. The number of dressing changes, incidence of blistering, leakage, appearance of inflammation, infection rate and the average stay in hospital was recorded for each patient. The jubilee dressing significantly reduced the rate of blistering, leakage and number of dressing changes when compare to a traditional adhesive dressing (p < 0.05). The rate of inflammation and average length of stay in hospital was not significantly different between the two groups. The authors recommend the use of this dressing for total hip and total knee arthroplasty procedures due to the associated lower complication rate. Copyright © 2012 Tissue Viability Society. Published by Elsevier Ltd. All rights reserved.
Simulation Analysis of the Mutual Influence of the Stress Intensity Factor on the Multiple Blisters Caused by Hydrogen Induced Damage

NASA Astrophysics Data System (ADS)

Ji, Congwei; Zhang, Shaojie; Wang, Hehui

2018-03-01

Hydrogen blisters are taken as the research object by using the finite element software ABAQUS. The stress intensity factors of blister cracks are numerically calculated at varying depths and different edge distances for established three-dimensional finite element models of single-blister and double-blisters, respectively. The mutual influence of the stress intensity factors of the multiple blisters is obtained. It shows that the blister crack is easier to expand when the crack is closer to inner wall of the cylinder. What’s more, the crack growth rate increases firstly and then decreases as the increasing of the distance between two blisters cracks. The investigated result is of great reference value for predicting the trend of blister crack growth.
Blisters

MedlinePlus

... get blisters? Blisters often happen when there is friction - rubbing or pressure - on one spot. For example, ... sure that there is no more rubbing or friction on the blister. You should contact your health ...

Determining the feasibility of objective adherence measurement with blister packaging smart technology.

PubMed

van Onzenoort, Hein A; Neef, Cees; Verberk, Willem W; van Iperen, H Peter; de Leeuw, Peter W; van der Kuy, Paul-Hugo M

2012-05-15

The results of a feasibility study of blister-pack smart technology for monitoring medication adherence are reported. Research in the area of objective therapy compliance measurement has led to the development of microprocessor-driven systems that record the time a unit dose is removed from blister packaging. One device under development is the Smart Blister-a label imprinted with event-detection circuitry that can be affixed to standard commercial blister cards. In the first trial of the device in actual clinical practice, 115 community-dwelling Dutch patients receiving valsartan maintenance therapy (160 mg once daily) were given 14-day blister packages equipped with the Smart Blister. On the return of empty blister cards to the 20 participating community pharmacies, the stored information was scanned and downloaded for data analysis and patient counseling purposes. A total of 245 Smart Blister-equipped packages were used by valsartan recipients during the eight-month study. The device was largely effective in recording patient and blister-card identification data and other desired information. However, in 17% of cases, the Smart Blister system registered multiple tablet-removal events at the same time, presumably indicating unintentional breakage of nearby conductive circuits and the need for design refinements. The Smart Blister-equipped medication cards were generally well received by patients and pharmacies. An evaluation of the functionality and robustness of the Smart Blister in a real-world clinical practice situation yielded some promising results, but the findings also indicated a need for design refinements and additional performance testing of the device.
DOE Office of Scientific and Technical Information (OSTI.GOV)

Genevée, Pascal, E-mail: pascal-genevee@chimie-paristech.fr, E-mail: a.szeghalmi@uni-jena.de; Ahiavi, Ernest; Janunts, Norik

The authors report on the formation of blisters during the atomic layer deposition of iridium using iridium acetylacetonate and oxygen precursors. Films deposited on fused silica substrates led to sparsely distributed large blisters while in the case of silicon with native oxide additional small blisters with a high density was observed. It is found that the formation of blisters is favored by a higher deposition temperature and a larger layer thickness. Postdeposition annealing did not have a significant effect on the formation of blisters. Finally, changing purge duration during the film growth allowed us to avoid blistering and evidenced thatmore » impurities released from the film in gas phase were responsible for the formation of blisters.« less
Investigation of blister formation in sputtered Cu{sub 2}ZnSnS{sub 4} absorbers for thin film solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bras, Patrice, E-mail: patrice.bras@angstrom.uu.se; Sterner, Jan; Platzer-Björkman, Charlotte

2015-11-15

Blister formation in Cu{sub 2}ZnSnS{sub 4} (CZTS) thin films sputtered from a quaternary compound target is investigated. While the thin film structure, composition, and substrate material are not correlated to the blister formation, a strong link between sputtering gas entrapment, in this case argon, and blistering effect is found. It is shown that argon is trapped in the film during sputtering and migrates to locally form blisters during the high temperature annealing. Blister formation in CZTS absorbers is detrimental for thin film solar cell fabrication causing partial peeling of the absorber layer and potential shunt paths in the complete device.more » Reduced sputtering gas entrapment, and blister formation, is seen for higher sputtering pressure, higher substrate temperature, and change of sputtering gas to larger atoms. This is all in accordance with previous publications on blister formation caused by sputtering gas entrapment in other materials.« less
Is cupping blister harmful?-A proteomical analysis of blister fluid induced by cupping therapy and scald.

PubMed

Liu, Zhidan; Chen, Chunlan; Li, Xiaoyan; Zhao, Chuang; Li, Zunyuan; Liang, Wei; Lin, Yufang

2018-02-01

Cupping therapy has a long history in traditional medicine especially in Asian countries. It was controversial whether cupping induced blisters are beneficial to healing effects, and the formation and content in the blisters remain unexplored. We aimed to identify and compare the molecular components of the blister fluid from the cupping therapy and the scalds to explore the necessary of inducing cupping induced blisters. Fluid sample of blisters from fifteen patients receiving cupping therapy (Cupping group) and scald burns (Scald group) were collected in this study. Proteins from the blisters were separated by two-dimensional electrophoresis (2D-gel) and further analyzed by mass spectrometry. In addition, the changes in particular proteins were confirmed by Western blotting. The protein components are significantly different between blister from cupping therapy and scalds. The immune responses, oxidative stress and metabolic related proteins (Ig lambda-2 chain C regions, Ig gamma-1 chain C region, hemopexin, prdx2, calmodulin, succinyl-CoA ligase and tetranectin) were increased, whereas the hemoglobin subunit beta was decreased in the Cupping group compared with the Scald group. Cupping induced blisters contain several proteins which relate to the activation of certain immune pathways including anti-oxidation, anti-apoptosis, tissue repairing and metabolic regulation. This proteomic analysis may indicate a significant clue to the mechanism study of cupping. Copyright © 2017 Elsevier Ltd. All rights reserved.
Epidemiology for hazard rating of white pine blister rust

Treesearch

Eugene P. Van Arsdel; Brian W. Geils; Paul J. Zambino

2006-01-01

The ability to assess the potential for a severe infestation of white pine blister rust is an important management tool. Successful hazard rating requires a proper understanding of blister rust epidemiology, including environmental and genetic factors. For the blister rust caused by Cronartium ribicola, climate and meteorology, and the ecology,...
Increased Activity and Apoptosis of Eosinophils in Blister Fluids, Skin and Peripheral Blood of Patients with Bullous Pemphigoid.

PubMed

Engmann, Judith; Rüdrich, Urda; Behrens, Georg; Papakonstantinou, Eleni; Gehring, Manuela; Kapp, Alexander; Raap, Ulrike

2017-04-06

Bullous pemphigoid (BP) is an autoimmune blistering skin disease that is more common in elderly individuals. The aim of this study was to determine the functional activity of eosinophils in patients with BP compared with healthy donors. Blood, skin and blister-derived eosinophils were strongly activated in patients with BP, seen by increased surface expression of CD69 compared with controls. CD11b was also increased in BP blood eosinophils, which may explain the striking accumulation of eosinophils in BP (1×106 per ml blister fluid). Furthermore, CCL26 was expressed by activated eosinophils in BP skin and in blister fluid. BP eosinophils also released IL-6, IL-8 and IL-1α in BP blister fluids. Apoptosis in cultivated BP eosinophils was increased and accompanied by enhanced surface externalization of CD95. Caspase 3 positive eosinophils in lesional BP skin and blister fluid also showed the initiation of apoptosis. These results reveal novel pathophysiological aspects of BP, with a strong activation pattern and increased apoptosis of eosinophils in the peripheral blood, skin and blister fluids.
Effect of solute elements in Ni alloys on blistering under He + and D + ion irradiation

NASA Astrophysics Data System (ADS)

Wakai, E.; Ezawa, T.; Takenaka, T.; Imamura, J.; Tanabe, T.; Oshima, R.

2007-08-01

Effects of solute atoms on microstructural evolution and blister formation have been investigated using Ni alloys under 25 keV He + and 20 keV D + irradiation at 500 °C to a dose of about 4 × 10 21 ions/m 2. The specimens used were pure Ni, Ni-Si, Ni-Co, Ni-Cu, Ni-Mn and Ni-Pd alloys. The volume size factors of solute elements for the Ni alloys range from -5.8% to +63.6%. The formations of blisters were observed in the helium-irradiated specimens, but not in the deuteron-irradiated specimens. The areal number densities of blisters increased with volume size difference of solute atoms. The dependence of volume size on the areal number densities of blisters was very similar to that of the number densities of bubbles on solute atoms. The size of the blisters inversely decreased with increasing size of solute atoms. The formation of blisters was intimately related to the bubble growth, and the gas pressure model for the formation of blisters was supported by this study.
Characterization of skin blister fluids from children with Epstein-Barr virus-associated lymphoproliferative disease.

PubMed

Wada, Taizo; Toma, Tomoko; Miyazawa, Hanae; Koizumi, Eiko; Shirahashi, Tetsujiro; Matsuda, Yusuke; Yachie, Akihiro

2018-04-01

Epstein-Barr virus (EBV)-associated T- or natural killer (NK)-cell lymphoproliferative disease (LPD) is a heterogeneous group of disorders characterized by chronic proliferation of EBV-infected lymphocytes. Patients may present with severe skin manifestations, including hypersensitivity to mosquito bites (HMB) and hydroa vacciniforme (HV)-like eruption, which are characterized by blister formation and necrotic ulceration. Skin biopsy specimens show inflammatory reactions comprising EBV-infected lymphocytes. However, blister fluids have not been fully assessed in patients with this disease. Blister fluids were collected from three patients with EBV-associated LPD: two with HMB and one with HV. Immunophenotyping of blister lymphocytes and measurement of tumor necrosis factor (TNF)-α in blister fluids were performed. The patients with HMB and HV exhibited markedly increased percentages of NK and γδ T cells, respectively, in both peripheral blood and blister fluids. These NK and γδ T cells strongly expressed the activation marker human leukocyte antigen-DR and were considered to be cellular targets of EBV infections. TNF-α was highly elevated in all blister fluids. Severe local skin reactions of EBV-associated LPD may be associated with infiltrating EBV-infected lymphocytes and a high TNF-α concentration in blister fluids. © 2018 Japanese Dermatological Association.
Investigation of the influence of textiles and surface treatments on blistering using a novel simulant.

PubMed

Guerra, C; Schwartz, C J

2012-02-01

Friction blisters occur when shear loading causes the separation of dermal layers. Consequences range from minor pain to life-threatening infection. Past research in blister formation has focused on in vivo experiments, which complicate a mechanics-based study of the phenomenon. A Synthetic Skin Simulant Platform (3SP) approach was developed to investigate the effect of textile fabrics (t-shirt knit and denim cottons) and surface treatments (dry and wet lubricants) on blister formation. 3SP samples consist of bonded elastomeric layers that are surrogates for various dermal layers. These layers display frictional and mechanical properties similar to their anatomical analogues. Blistering was assessed by the measurement of deboned area between layers. Denim caused greater blistering than did the t-shirt knit cotton, and both lubricants significantly reduced blister area and surface damage. A triglyceride-based lubricant had a more pronounced effect on blister reduction than corn starch. The triglyceride lubricant used with t-shirt knit cotton resulted in no blisters being formed. The performance of the 3SP approach follows previously reported frictional behavior of skin in vivo. The results of textile and surface treatment performance suggest that future 3SP iterations can be focused on specific anatomical sites based on application type. © 2011 John Wiley & Sons A/S.
Paper Tape Prevents Foot Blisters: A Randomized Prevention Trial Assessing Paper Tape in Endurance Distances II (Pre-TAPED II).

PubMed

Lipman, Grant S; Sharp, Louis J; Christensen, Mark; Phillips, Caleb; DiTullio, Alexandra; Dalton, Andrew; Ng, Pearlly; Shangkuan, Jennifer; Shea, Katherine; Krabak, Brian J

2016-09-01

To determine whether paper tape prevents foot blisters in multistage ultramarathon runners. Multisite prospective randomized trial. The 2014 250-km (155-mile) 6-stage RacingThePlanet ultramarathons in Jordan, Gobi, Madagascar, and Atacama Deserts. One hundred twenty-eight participants were enrolled: 19 (15%) from the Jordan, 35 (27%) from Gobi, 21 (16%) from Madagascar, and 53 (41%) from the Atacama Desert. The mean age was 39.3 years (22-63) and body mass index was 24.2 kg/m (17.4-35.1), with 31 (22.5%) females. Paper tape was applied to a randomly selected foot before the race, either to participants' blister-prone areas or randomly selected location if there was no blister history, with untaped areas of the same foot used as the control. Development of a blister anywhere on the study foot. One hundred six (83%) participants developed 117 blisters, with treatment success in 98 (77%) runners. Paper tape reduced blisters by 40% (P < 0.01, 95% confidence interval, 28-52) with a number needed to treat of 1.31. Most of the study participants had 1 blister (78%), with most common locations on the toes (n = 58, 50%) and heel (n = 27, 23%), with 94 (80%) blisters occurring by the end of stage 2. Treatment success was associated with earlier stages [odds ratio (OR), 74.9, P < 0.01] and time spent running (OR, 0.66, P = 0.01). Paper tape was found to prevent both the incidence and frequency of foot blisters in runners.
Heterogeneous nonmarket benefits of managing white pine bluster rust in high-elevation pine forests

Treesearch

James R. Meldrum; Patricia A. Champ; Craig A. Bond

2013-01-01

This article describes a nonmarket valuation study about benefits of managing the invasive disease white pine blister rust in highelevation forests in the Western United States. Results demonstrate that, on average, households in the Western United States are willing to pay $154 to improve the resiliency of these forests. Factor analysis shows that long-run protection...
Inheritance of the bark reaction resistance mechanism in Pinus monticola infected by Cronartium ribicola

Treesearch

Ray J. Hoff

1986-01-01

Necrotic reactions in branch or main stems of western white pine (Pinus monticola Dougl.) caused by infection by the blister rust fungus (Cronartium ribicola J. C. Fisch. ex Rabenh.) are a major mechanism of resistance. Overall, 26 percent of the seedlings eliminated the fungus via this defense system. Heritability based upon crossing family groups averaged 33 percent...
Whitebark Pine Germination, Rust Resistance, and Cold Hardiness Among Seed Sources in the Inland Northwest: Planting Strategies for Restoration

Treesearch

Mary F. Mahalovich; Karen E. Burr; David L. Foushee

2006-01-01

A synthesis of several studies highlights above-average performing seed sources (n = 108) of whitebark pine (Pinus albicaulis), which practitioners can utilize for restoration, wildlife habitat improvement, and operational planting programs. It is the first report of this magnitude of blister rust resistance for this species. Whitebark pine does have...
ICAM-1, ELAM-1, TNF-alpha and IL-6 in serum and blister liquid of pemphigus vulgaris patients.

PubMed

Alecu, M; Alecu, S; Coman, G; Gălăţescu, E; Ursaciuc, C

1999-01-01

The levels of ICAM-1, ELAM-1, TNF-alpha and IL-6 were determined in 12 patients with pemphigus vulgaris (PV) both in serum and the blister liquid. As a control, the same parameters were determined in 7 patients with herpes zoster (HZ). The patients with PV presented significantly higher values of ICAM-1 in the blister liquid, as compared to the serum values. The values of TNF-alpha and IL-6 were increased both in serum and the blister liquid. The ELAM-1 values did not show significant differences between serum and the blister liquid. In HZ patients, the blister liquid values did not significantly exceed the serum values both for ICAM-1 and ELAM-1. TNF-alpha and IL-6 presented high values both in serum and the blister liquid. We consider that the high values of ICAM-1 in the blister liquid from PV patients suggest the involvement of this adhesion molecule in the PV pathogenic features. The implication of ICAM-1 could be nonspecific and limited, and could possibly represent a reaction to the destruction of the desmosomal bonds within keratinocytes.
Ease of opening of blistered solid dosage forms in a senior citizens target group.

PubMed

Braun-Münker, Myriam; Ecker, Felix

2016-10-30

Blisters differing in design and handling are established as packaging material for solid dosage forms. The ease of opening of blisters influences application and patient's compliance. In this study the influence of visibility and movability of solid dosage forms in blister packaging on both, easy opening and patient's satisfaction, were investigated by target group testing according to ONR CEN/TS 15945. For each testing 20 participants in the age of 65-80 years were recruited randomly. They opened the blisters on realistic terms without any auxiliary devices. Video documentation of the hands' movements was recorded to analyze the opening procedure. To show the influence of visibility of the dosage form in the blister, capsules size 1 were packed in transparent and opaque blisters. A moderate influence of the visibility on both, the ease of opening and patient satisfaction, was observed. A second study dealt with the movability of solid dosage forms in blisters. Therefore, three different sizes of tablets with similar shapes were packed in identical cavities. Limited movability was found as major criterion on effectiveness and effectivity of opening as well as on satisfaction with the opening procedure. Copyright © 2015 Elsevier B.V. All rights reserved.
Blister formation at subcritical doses in tungsten irradiated by MeV protons

NASA Astrophysics Data System (ADS)

Gavish Segev, I.; Yahel, E.; Silverman, I.; Makov, G.

2017-12-01

The material response of tungsten to irradiation by MeV protons has been studied experimentally, in particular with respect to bubble and blister formation. Tungsten samples were irradiated by 2.2 MeV protons at the Soreq Applied Research Accelerator Facility (SARAF) to doses of the order of 1017 protons/cm2 which are below the reported critical threshold for blister formation derived from keV range irradiation studies. Large, well-developed blisters are observed indicating that for MeV range protons the critical threshold is at least an order of magnitude lower than the lowest value reported previously. The effects of fluence, flux, and corresponding temperature on the distribution and characteristics of the obtained blisters were studied. FIB cross sections of several blisters exposed their depth and structure.
Corrosion-Resistant Roof with Integrated Photovoltaic Power System

DTIC Science & Technology

2014-02-01

Figure 9. The panels are coated with a PVDF organic coating on the external facing surface and polyester enamel on the interior-facing surface. The high...1 no scribe No evidence of blistering, cracking , peeling or delaminating #2 scribe No evidence of blistering, cracking , peeling or delaminating...3 scribe No evidence of blistering, cracking , peeling or delaminating #4 scribe No evidence of blistering, cracking , peeling or delaminating
Influence of an Antiperspirant on Foot Blister Incidence during Cross-Country Hiking

DTIC Science & Technology

1999-11-01

blisters also increases. Therefore reducing Moisture may reduce blister incidence during physical activity. Objective: We examined whether an antiperspirant ...that used either an antiperspirant (20% aluminum chloride hexahydrate in anhydrous ethyl alcohol) or placebo (anhydrous ethyl alcohol) preparation...blisters before and after. Results: Because of dropouts, the final sample size was 667 cadets with 328 in the antiperspirant group and 339 in the
High levels of interleukin-8, soluble CD4 and soluble CD8 in bullous pemphigoid blister fluid. The relationship between local cytokine production and lesional T-cell activities.

PubMed

Sun, C C; Wu, J; Wong, T T; Wang, L F; Chuan, M T

2000-12-01

Bullous pemphigoid (BP) is an inflammatory subepidermal blistering disease associated with autoantibodies that recognize hemidesmosomal proteins. In addition to autoantibodies, the cell-mediated immune reaction is considered to play an important part in blister formation. Objectives To investigate some T-cell activation markers and inflammatory cytokines in the blister fluid and sera of patients with BP. We measured soluble CD4 (sCD4) and soluble CD8 (sCD8), which have been, respectively, associated with CD4 and CD8 T-cell activation. Enzyme-linked immunosorbent assays were also used to quantify the production of the leucocyte chemoattractant interleukin (IL) -8 and of the cytokines IL-1alpha, IL-1beta, IL-6, IL-10 and tumour necrosis factor-alpha in the blister fluid and sera of 11 patients with BP. The mean +/- SD level of sCD4 in patients' blisters (42.4 +/- 25.0 units mL-1) was significantly elevated (P < 0.005) compared with that in their sera (11.2 +/- 8.9) and that in the suction blisters of 10 healthy people (11.4 +/- 5.4; P < 0.005). Mean +/- SD IL-8 concentrations in BP blisters (4683.6 +/- 3878.1 pg mL-1) were much higher than those in their sera (17.1 +/- 18.9; P < 0.001), and were very significantly elevated (P < 0.005) in comparison with those in suction blisters of healthy persons (512 +/- 292). sCD4 levels in BP blisters were inversely related to IL-10 levels (P = 0. 03, r2 = 0.85), IL-8 levels were positively related to sCD8 levels (P = 0.01, r2 = 0.54), and IL-1beta levels were positively related to sCD8 concentrations (P < 0.005, r2 = 0.65). The correlations suggest that there is a delicately orchestrated network of cytokines and cell-mediated immunity operating in BP blisters.
Blisters, Calluses, and Corns

MedlinePlus

... for Educators Search English Español Blisters, Calluses, and Corns KidsHealth / For Kids / Blisters, Calluses, and Corns What's ... used to all of that stress. What's a Corn? Like calluses, corns are also areas of hard, ...

Hydrogen blistering under extreme radiation conditions

NASA Astrophysics Data System (ADS)

Sznajder, Maciej; Geppert, Ulrich; Dudek, Miroslaw

2018-01-01

Metallic surfaces, exposed to a proton flux, start to degradate by molecular hydrogen blisters. These are created by recombination of protons with metal electrons. Continued irradiation progresses blistering, which is undesired for many technical applications. In this work, the effect of the proton flux magnitude onto the degradation of native metal oxide layers and its consequences for blister formation has been examined. To study this phenomenon, we performed proton irradiation experiments of aluminium surfaces. The proton kinetic energy was chosen so that all recombined hydrogen is trapped within the metal structure. As a result, we discovered that intense proton irradiation increases the permeability of aluminium oxide layers for hydrogen atoms, thereby counteracting blister formation. These findings may improve the understanding of the hydrogen blistering process, are valid for all metals kept under terrestrial ambient conditions, and important for the design of proton irradiation tests.
The Causes of Boat Hull Blisters

DTIC Science & Technology

1987-05-01

blistering. The report is divided into the following sections: Introduction; How Blisters Form; the Hull Material; Manufacturing Processes; Water Diffusion...Term Effects of Water Up-Takeo " The much more detailed and highly technical report of thia-Vsrk is entitled "The Causes of Blistering in Boat Building...Chemical Engineering, ably assisted by several graduate students, and was completed in the fall of 1986. The report itself, d List-ribution/_ Availabilit
Relationship between theoretical molecular weight and blister fluid/serum ratio of cytokines and five other molecules evaluated in patients with bullous pemphigoid.

PubMed

D'Auria, L; Pimpinelli, F; Ferraro, C; D'Ambrogio, G; Giacalone, B; Bellocci, M; Ameglio, F

1998-01-01

Bullous pemphigoid (BP) blisters contain several molecules, some of which spread into the blisters from the interstitial fluid, while others are produced locally and migrate into the circulation. The calculation of the ratios between blister/serum concentrations may help to distinguish between these two types of molecules. The rules regulating the diffusion of the molecules have been described only in suction blisters, where the theoretical molecular weight (MW) represents one of the principal influencing factors. The aim of the present study was to analyse the relationship between theoretical MWs and the ratios of concentrations of several molecules evaluated both in sera and in blister fluids. Eight cytokines (interleukin-2, interleukin-3, interleukin-4, interleukin-5, interleukin-10, tumor necrosis factor-alpha, oncostatin-M and vascular endothelial growth factor), two acute phase reactants (alpha-1 acid glycoprotein, haptoglobin), albumin, one soluble membrane molecule with adhesion functions (sICAM-1) and the eosinophil cathionic protein (ECP) were measured in samples from 15 patients affected with BP by means of commercially available tests. The data suggest that the MW may influence the rate of diffusion throughout the blister, both in input and output directions, despite the discontinuity observed at the basement membrane level on the BP blister floor.
Behavior of implanted hydrogen in thermally stimulated blistering in silicon

NASA Astrophysics Data System (ADS)

Aleksandrov, P. A.; Baranova, E. K.; Baranova, I. V.; Budaragin, V. V.; Litvinov, V. L.

2003-11-01

The processes of accumulation of ion implanted hydrogen in blisters in silicon and its release during the thermal treatment from 350 to 1020degreesC have been studied by optical techniques. It was established that accumulation of gaseous hydrogen inside blisters takes place at temperatures lower than similar to450-500degreesC and is accompanied by the growth of blister thickness and deformation of their caps. At higher temperatures the gaseous hydrogen goes out of the cavities dissolving in silicon. Due to the internal pressure dropping the elastically deformed top layer partially relaxes and the blister thickness decreases. Etching of the surface layer reveals the agglomerations of small voids (<0.3 mm) located in the place of blisters approximately at their depth. Proceeding from the fact that the processes in blistering are similar to those in ion cut, the following conclusions with respect to the latter were drawn. The exfoliation processes themselves occur at temperatures lower than similar to500degreesC. The exfoliation efficiency particularly at the higher temperatures is essentially dependent on the heating rate.
Hand Blisters in Major League Baseball Pitchers: Current Concepts and Management.

PubMed

McNamara, Andrew R; Ensell, Scott; Farley, Timothy D

2016-01-01

Friction blisters are a common sequela of many athletic activities. Their significance can range from minor annoyance to major performance disruptions. The latter is particularly true in baseball pitchers, who sustain repeated trauma between the baseball seams and the fingers of the pitching hand, predominately at the tips of the index and long fingers. Since 2010, 6 Major League Baseball (MLB) players accounted for 7 stints on the disabled list (DL) due to blisters. These injuries resulted in a total of 151 days spent on the DL. Since 2012, 8 minor league players spent time on the DL due to blisters. Moreover, there have been several documented and publicized instances of professional baseball pitchers suffering blisters that did not require placement on the DL but did result in injury time and missed starts. The purpose of this article is to review the etiology and pathophysiology of friction blisters with particular reference to baseball pitchers; provide an overview of past and current prevention methods; and discuss our experience in treating friction blisters in MLB pitchers.
Blister fluid cytokines in cutaneous inflammatory bullous disorders.

PubMed

Rhodes, L E; Hashim, I A; McLaughlin, P J; Friedmann, P S

1999-07-01

Cytokines are important regulators of immune and inflammatory reactions in the skin, and may contribute to inflammatory blister induction. We examined the profiles of interleukin-6 (IL-6) and tumour necrosis factor-alpha (TNF-alpha) in fluid of spontaneous blisters in the immune-based inflammatory disorders bullous pemphigoid (8 patients), allergic contact dermatitis (5 patients) and toxic epidermal necrolysis (5 patients). These were compared with levels in 9 patients with burns, i.e. inflammatory blisters of non-immune aetiology, and 4 patients with blisters of physical origin. Very high levels of IL-6 were found in bullous pemphigoid and toxic epidermal necrolysis (p<0.001) compared with non-inflammatory and burn blisters. TNF-alpha levels were high in bullous pemphigoid and burns, but undetectable in non-inflammatory blisters. The pattern in bullous pemphigoid (very high IL-6, high TNF-alpha) differed substantially from toxic epidermal necrolysis (very high IL-6, low TNF-alpha), while burns and allergic contact dermatitis showed lesser elevation of both cytokines. Hence, differences in cytokine profiles were identified, although the relevance to underlying pathomechanisms is uncertain.
Cleaning to favor western white pine - its effects upon composition, growth, and potential values

Treesearch

Raymond J. Boyd

1959-01-01

The management of western white pine (Pinus monticola) requires the production of a high proportion of valuable white pine crop trees in order to defray the costs of protection from blister rust. Current average selling prices of lumber give white pine about $50 per m.b.f. advantage over western larch (Larix occidentalis) and Douglas-fir (Pseudotsuga menziesii), the...
Prevention of foot blisters.

PubMed

Knapik, Joseph J

2014-01-01

Foot blisters are the most common medical problem faced by Soldiers during foot march operations and, if untreated, they can lead to infection. Foot blisters are caused by boots rubbing on the foot (frictional forces), which separates skin layers and allows fluid to seep in. Blisters can be prevented by wearing properly sized boots, conditioning feet through regular road marching, wearing socks that reduce reduce friction and moisture, and possibly applying antiperspirants to the feet. 2014.
Burn wound sepsis may be promoted by a failure of local antibacterial host defenses.

PubMed Central

Deitch, E A; Bridges, R M; Dobke, M; McDonald, J C

1987-01-01

Little attention has been focused on the local burn wound environment, even though burn wound sepsis is a common cause of death in the burn victim. To characterize the effect of the local burn wound environment on neutrophil function and metabolism, the opsonic activity of blister fluid specimens against Pseudomonas aeruginosa was measured as was the effect of blister fluid on control neutrophil oxygen consumption using preopsonized zymosan and f-met-leu-phe (FMLP) as stimuli. Blister fluid did not support the killing of P. aeruginosa by normal neutrophils as well as normal serum. Additionally, blister fluid inhibited zymosan-stimulated, but not FMLP-stimulated, neutrophil oxygen consumption. The inhibitory effect of blister fluid on zymosan-stimulated oxygen consumption correlated with the extent of complement activation, measured as C3d or C3AI (p less than 0.01). That blister fluid did not inhibit the FMLP-mediated respiratory burst supports the concept that the blister fluid inhibitory effect on the zymosan-mediated respiratory burst was mediated through the complement receptor. These findings that blister fluid can affect the bactericidal and metabolic activity of normal neutrophils support the concept that cellular function can be altered by the microenvironment in which the cells are bathed. This potential impairment of host defenses within the burn wound could predispose the burn victim to burn wound sepsis. PMID:3115207
Injuries Associated with the 580 km University Student Grand Voluntary Road March: Focus on Foot Injuries

PubMed Central

Choi, Sang-cheon; Min, Young-Gi; Lee, In-Soo; Yoon, Gi-Ho; Kang, Bo-Ra; Jung, Yoon-Seok; Cho, Joon-Pil

2013-01-01

College student volunteers (n = 142) completed a 580 km road march for 21 consecutive days. Each volunteer carried a backpack that weighed 14.1 ± 1.4 kg on the average. We investigated the incidence and location of blisters associated with the road march using a foot map along with other injuries. Overall, 95.1% of the subjects (135 of 142) sustained one or more injuries. All injured subjects had foot blisters, and 18% had other foot injuries. The most common locations of blister development were the right 5th toe (61%) and the left 5th toe (57%). The little toes seem to have been subjected to the greatest friction and shearing forces. March-related injuries, excluding foot injuries, were ankle pain (12.7%), knee pain (12.7%) and Achilles tendon pain (7.7%). Six subjects (4.2%) needed extra medical treatment for more than 2 weeks prior to returning to their daily lives after completion of the march due to associated injuries. The present study observed a very high incidence rate of injuries (95.1%) associated with the 580 km university students grand road march. These injuries posed an obstacle against completion of the road march and against returning to daily life. Active preventive interventions such as physical therapy and customized reinforced shoes and education program are recommended for reducing incidence rate and severity of injuries. PMID:24339714
Basal cell carcinoma in young women: an evaluation of the association of tanning bed use and smoking.

PubMed

Boyd, Alan S; Shyr, Yu; King, Lloyd E

2002-05-01

Basal cell carcinomas (BCCs) typically occur in middle-aged to elderly patients but less commonly in younger ones. In our experience, most BCCs seen in patients younger than 40 years are found in women. We evaluated 30 women with biopsy-proven BCC and 30 control patients matched for sex, age, and skin type to determine potential risk factors for this population. Tanning bed visits, pack-years of cigarette smoking, recreational sun exposure, number of blistering sunburns, and use of sunscreens were determined for both groups. Among patients with a BCC, the histologic type of tumor, site of involvement, method of treatment, follow-up period, incidence of recurrence, and presence of actinic keratoses were also evaluated. Patients with a BCC had a statistically greater number of pack years of smoking (P =.045), and a greater percentage of these women had experienced blistering sunburns (P =.028). Although women with a BCC had, on average, almost twice as many tanning salon visits (152.2 vs 83.1), this was not statistically significant. Sunscreen use and amount of recreational ultraviolet light exposure were essentially equal between the two groups. Young women with a BCC are more likely to have a past or current history of cigarette smoking and blistering sunburns. Repeated exposure to tanning beds may also be a contributory factor.
Long-term follow-up analysis of microsurgical clip ligation and endovascular coil embolization for dorsal wall blister aneurysms of the internal carotid artery.

PubMed

Brown, Mason A; Guandique, Cristian F; Parish, Jonathan; McMillan, Aubrey C; Lehnert, Stephen; Mansour, Nassir; Tu, Michael; Bohnstedt, Bradley N; Payner, Troy D; Leipzig, Thomas J; DeNardo, Andrew J; Scott, John A; Cohen-Gadol, Aaron A

2017-05-01

Blister aneurysms at non-branching sites of the dorsal internal carotid artery (dICA) are fragile, rare, and often difficult to treat. The purpose of this study is to address the demographics, treatment modalities, and long-term outcome of patients treated for dICA blister aneurysms. A retrospective review of medical records identified all consecutive patients who presented with a blister aneurysm from 2002 to 2011 at our institution. Eighteen patients (M=7, F=11; mean age: 48.4±15.1years; range: 15-65years) harbored a total of 43 aneurysms, 25 of which were dorsal wall blister aneurysms of the ICA. Eleven (61.1%) patients presented with aneurysmal subarachnoid hemorrhage (aSAH), and 10 (55.6%) patients had multiple aneurysms at admission. Twelve patients had 18 aneurysms that were treated microsurgically. Five (41.7%) of these patients had a single recurrence that was retreated with subsequent repeat clip ligation. Six patients had 7 blister aneurysms that were treated with endovascularly. One (16.7%) of these patients had a single recurrence that was retreated with subsequent coil embolization. Postoperative vasospasm occurred in 8 (44.4%) patients, one of whom suffered from a stroke. This is one of the largest single-institution dICA blister aneurysm studies to date. There was no detected significant difference between microsurgical clip ligation and endovascular coil embolization in terms of surgical outcome. These blister aneurysms demonstrate a propensity to be associated with multiple cerebral aneurysms. Strict clinical and angiographic long-term follow-up may be warranted. Blister aneurysms are focal wall defects covered by a thin layer of fibrous tissue and adventitia, lacking the usual collagenous layer. Due to their pathologically thin vessel wall, blister aneurysms are prone to rupture. The management of these rare and fragile aneurysms presents a number of challenges. Here, we address the long-term outcome of patients treated for blister aneurysms at non-branching sites of the dICA. The presented data and analysis is imperative to determine the necessary strict long-term clinical and angiographic follow-up. Copyright © 2017 Elsevier Ltd. All rights reserved.
How to recognize blister rust infection on whitebark pine

Treesearch

Ray J. Hoff

1992-01-01

Color photographs show how white pine blister rust can be identified. In addition, the photographs show how pines resistant to the fungus could be identified. Such trees could be used to develop a new variety of whitebark pine that is resistant to blister rust.
Research Techniques Made Simple: Mouse Models of Autoimmune Blistering Diseases.

PubMed

Pollmann, Robert; Eming, Rüdiger

2017-01-01

Autoimmune blistering diseases are examples of autoantibody-mediated, organ-specific autoimmune disorders. Based on a genetic susceptibility, such as a strong HLA-class II association, as yet unknown triggering factors induce the formation of circulating and tissue-bound autoantibodies that are mainly directed against adhesion structures of the skin and mucous membranes. Compared with other autoimmune diseases, especially systemic disorders, the pathogenicity of autoimmune blistering diseases is relatively well described. Several animal models of autoimmune blistering diseases have been established that helped to uncover the immunological and molecular mechanisms underlying the blistering phenotypes. Each in vivo model focuses on specific aspects of the autoimmune cascade, from loss of immunological tolerance on the level of T and B cells to the pathogenic effects of autoantibodies upon binding to their target autoantigen. We discuss current mouse models of autoimmune blistering diseases, including models of pemphigus vulgaris, bullous pemphigoid, epidermolysis bullosa acquisita, and dermatitis herpetiformis. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.
Batch fabrication of optical actuators using nanotube-elastomer composites towards refreshable Braille displays

NASA Astrophysics Data System (ADS)

Camargo, C. J.; Campanella, H.; Marshall, J. E.; Torras, N.; Zinoviev, K.; Terentjev, E. M.; Esteve, J.

2012-07-01

This paper reports an opto-actuable device fabricated using micro-machined silicon moulds. The actuating component of the device is made from a composite material containing carbon nanotubes (CNTs) embedded in a liquid crystal elastomer (LCE) matrix. We demonstrate the fabrication of a patterned LCE-CNT film by a combination of mechanical stretching and thermal cross-linking. The resulting poly-domain LCE-CNT film contains ‘blister-shaped’ mono-domain regions, which reversibly change their shape under light irradiation and hence can be used as dynamic Braille dots. We demonstrate that blisters with diameters of 1.0 and 1.5 mm, and wall thickness 300 µm, will mechanically contract under irradiation by a laser diode with optical power up to 60 mW. The magnitude of this contraction was up to 40 µm, which is more than 10% of their height in the ‘rest’ state. The stabilization time of the material is less than 6 s for both actuation and recovery. We also carried out preliminary tests on the repeatability of this photo-actuation process, observing no material or performance degradation. This manufacturing approach establishes a starting point for the design and fabrication of wide-area tactile actuators, which are promising candidates for the development of new Braille reading applications for the visually impaired.
DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell K Meyer

Blister–threshold testing of fuel plates is a standard method through which the safety margin for operation of plate-type in research and test reactors is assessed. The blister-threshold temperature is indicative of the ability of fuel to operate at high temperatures for short periods of time (transient conditions) without failure. This method of testing was applied to the newly developed U-Mo monolithic fuel system. Blister annealing studies on the U-Mo monolithic fuel plates began in 2007, with the Reduced Enrichment for Research and Test Reactors (RERTR)-6 experiment, and they have continued as the U-Mo fuel system has evolved through the researchmore » and development process. Blister anneal threshold temperatures from early irradiation experiments (RERTR-6 through RERTR-10) ranged from 400 to 500°C. These temperatures were projected to be acceptable for NRC-licensed research reactors and the high-power Advanced Test Reactor (ATR) and the High Flux Isotope Reactor (HFIR) based on current safety-analysis reports (SARs). Initial blister testing results from the RERTR-12 experiment capsules X1 and X2 showed a decrease in the blister-threshold temperatures. Blister threshold temperatures from this experiment ranged from 300 to 400°C. Selected plates from the AFIP-4 experiment, which was fabricated using a process similar to that used to fabricate the RERTR-12 experiment, also underwent blister testing to determine whether results would be similar. The measured blister-threshold temperatures from the AFIP-4 plates fell within the same blister-threshold temperature range measured in the RERTR-12 plates. Investigation of the cause of this decrease in bister threshold temperature is being conducted under the guidance of Idaho National Laboratory PLN-4155, “Analysis of Low Blister Threshold Temperatures in the RERTR-12 and AFIP-4 Experiments,” and is driven by hypotheses. The main focus of the investigation is in the following areas: 1. Fabrication variables 2. Pre-irradiation characterization 3. Irradiation conditions 4. Post-irradiation examination 5. Additional blister testing 6. Mechanical modeling This report documents the preliminary results of this investigation. Several hypotheses can be dismissed as a result of this investigation. Two primary categories of causes remain. The most prominent theory, supported by the data, is that low blister-threshold temperature is the result of mechanical energy imparted on the samples during the fabrication process (hot and cold rolling) without adequate post processing (annealing). The mechanisms are not clearly understood and require further investigation, but can be divided into two categories: • Residual Stress • Undesirable interaction boundary and/or U-Mo microstructure change A secondary theory that cannot be dismissed with the information that is currently available is that a change in the test conditions has resulted in a statistically significant downward shift of measured blister temperature. This report outlines the results of the forensic investigations conducted to date. The data and conclusions presented in this report are preliminary. Definitive cause and effect relationships will be established by future experimental programs.« less
Measuring Patient Adherence to Malaria Treatment: A Comparison of Results from Self-Report and a Customised Electronic Monitoring Device

PubMed Central

Bruxvoort, Katia; Festo, Charles; Cairns, Matthew; Kalolella, Admirabilis; Mayaya, Frank; Kachur, S. Patrick; Schellenberg, David; Goodman, Catherine

2015-01-01

Background Self-report is the most common and feasible method for assessing patient adherence to medication, but can be prone to recall bias and social desirability bias. Most studies assessing adherence to artemisinin-based combination therapies (ACTs) have relied on self-report. In this study, we use a novel customised electronic monitoring device—termed smart blister packs—to examine the validity of self-reported adherence to artemether-lumefantrine (AL) in southern Tanzania. Methods Smart blister packs were designed to look identical to locally available AL blister packs and to record the date and time each tablet was removed from packaging. Patients obtaining AL at randomly selected health facilities and drug stores were followed up at home three days later and interviewed about each dose of AL taken. Blister packs were requested for pill count and extraction of smart blister pack data. Results Data on adherence from both self-report verified by pill count and smart blister packs were available for 696 of 1,204 patients. There was no difference between methods in the proportion of patients assessed to have completed treatment (64% and 67%, respectively). However, the percentage taking the correct number of pills for each dose at the correct times (timely completion) was higher by self-report than smart blister packs (37% vs. 24%; p<0.0001). By smart blister packs, 64% of patients completing treatment did not take the correct number of pills per dose or did not take each dose at the correct time interval. Conclusion Smart blister packs resulted in lower estimates of timely completion of AL and may be less prone to recall and social desirability bias. They may be useful when data on patterns of adherence are desirable to evaluate treatment outcomes. Improved methods of collecting self-reported data are needed to minimise bias and maximise comparability between studies. PMID:26214848
Problems experienced by older people when opening medicine packaging.

PubMed

Philbert, Daphne; Notenboom, Kim; Bouvy, Marcel L; van Geffen, Erica C G

2014-06-01

Medicine packages can cause problems in daily practice, especially among older people. This study aimed to investigate the prevalence of problems experienced by older people when opening medicine packaging and to investigate how patients manage these problems. A convenience sample of 30 community pharmacies participated in this study. They selected a systematic sample of 30 patients over 65 years old with a recent omeprazole prescription, and a questionnaire was administered by telephone for at least 10 patients per pharmacy. A total of 317 patients completed the questionnaire. They received their omeprazole in a bottle (n = 179, 56.5%), push-through blister pack (n = 102, 32.2%) or peel-off blister pack (n = 36, 11.4%). Some 28.4% of all patients experienced one or more problems with opening their omeprazole packaging; most problems occurred with peel-off blisters (n = 24, 66.7% of all respondents using peel-off blisters), followed by push-through blisters (n = 34, 33.3%) and finally bottles (n = 32, 17.9%). The risk of experiencing problems with peel-off blisters and push-through blisters was higher [relative risk 3.7 (95% confidence interval 2.5-5.5) and 1.9 (1.2-2.8), respectively] than the risk of experiencing problems with opening bottles. Two-thirds of respondents reported management strategies for their problems. Most were found for problems opening bottles (n = 24, 75%), followed by push-through blisters (n = 24, 70.6%) and peel-off blisters (n = 14, 58.3%). One in four patients over 65 experienced difficulties opening their omeprazole packaging and not all of them reported a management strategy for their problems. Manufacturers are advised to pay more attention to the user-friendliness of product packaging. In addition, it is important that pharmacy staff clearly instruct patients on how to open their medicine packaging, or assist them in choosing the most appropriate packaging. © 2013 Royal Pharmaceutical Society.
Detection of Anti-basement Membrane Zone Antibodies in the Blister Fluid in Subepidermal Autoimmune Bullous Diseases

PubMed Central

Surya, Ravindran; Tejasvi, Bobbili; Shenoi, Shrutakirthi D; Pai, Sathish; Rao, Chythra; Rao, Raghavendra

2017-01-01

Background: Subepidermal autoimmune bullous diseases (sAIBD) are diverse of conditions with clinicopathological overlap. Circulating autoantibodies in the serum can be demonstrated using indirect immunofluorescence (IIF) microscopy. Artificially split normal human skin is considered as an optimum substrate for the demonstration of anti-basement membrane zone (BMZ) antibodies using IIF in sAIBD; it not only helps to detect the presence of circulating antibodies in the serum but also helps to subclassify these conditions into “roof” and “floor” binding disorders. Aim: In this study, we evaluated the utility of IIF to detect anti-BMZ antibodies in the blister fluid of patients with sAIBD. Materials and Methods: Twenty-two patients with a clinical diagnosis of sAIBD were enrolled in the study. IIF of serum and blister fluid were done simultaneously using salt-split skin as a substrate. Results: Anti-BMZ antibodies could be detected in the blister fluid using IIF in all patients in the study group. Limitation: We could not do enzyme-linked immunosorbent assay of blister fluid. This would have given us the quantitative data of circulating antibodies in the blister fluid. Conclusion: Blister fluid offers an alternate source for the detection of autoantibodies in patients with sAIBD. It may be of particular help in children and in elderly with poor venous access. PMID:29263541
21 CFR 310.537 - Drug products containing active ingredients offered over-the-counter (OTC) for oral...

Code of Federal Regulations, 2012 CFR

2012-04-01

... offered over-the-counter (OTC) for oral administration for the treatment of fever blisters and cold sores... the treatment of fever blisters and cold sores. (a) l-lysine (lysine, lysine hydrochloride... products to treat fever blisters and cold sores. There is a lack of adequate data to establish general...

21 CFR 310.537 - Drug products containing active ingredients offered over-the-counter (OTC) for oral...

Code of Federal Regulations, 2014 CFR

2014-04-01

... offered over-the-counter (OTC) for oral administration for the treatment of fever blisters and cold sores... the treatment of fever blisters and cold sores. (a) l-lysine (lysine, lysine hydrochloride... products to treat fever blisters and cold sores. There is a lack of adequate data to establish general...
21 CFR 310.537 - Drug products containing active ingredients offered over-the-counter (OTC) for oral...

Code of Federal Regulations, 2013 CFR

2013-04-01

... offered over-the-counter (OTC) for oral administration for the treatment of fever blisters and cold sores... the treatment of fever blisters and cold sores. (a) l-lysine (lysine, lysine hydrochloride... products to treat fever blisters and cold sores. There is a lack of adequate data to establish general...
21 CFR 310.537 - Drug products containing active ingredients offered over-the-counter (OTC) for oral...

Code of Federal Regulations, 2011 CFR

2011-04-01

... offered over-the-counter (OTC) for oral administration for the treatment of fever blisters and cold sores... the treatment of fever blisters and cold sores. (a) l-lysine (lysine, lysine hydrochloride... products to treat fever blisters and cold sores. There is a lack of adequate data to establish general...
Can microscale meteorological conditions predict the impact of white pine blister rust in Colorado and Wyoming?

Treesearch

William R. Jacobi; Betsy A. Goodrich; Holly S. J. Kearns; Kelly S. Burns; Brian W. Geils

2011-01-01

White pine blister rust occurs when there are compatible interactions between susceptible hosts (white pines and Ribes spp.), inoculum (Cronartium ribicola spores), and local weather conditions during infection. The five spore stages of the white pine blister rust (WPBR) fungus have specific temperature and moisture conditions necessary for production, germination, and...
White pines, blister rust, and management in the Southwest

Treesearch

D. A. Conklin; M Fairweather; D Ryerson; B Geils; D Vogler

2009-01-01

White pines in New Mexico and Arizona are threatened by the invasive disease white pine blister rust, Cronartium ribicola. Blister rust is already causing severe damage to a large population of southwestern white pine in the Sacramento Mountains of southern New Mexico. Recent detection in northern and western New Mexico suggests that a major expansion of the...
A prospective randomized blister prevention trial assessing paper tape in endurance distances (Pre-TAPED).

PubMed

Lipman, Grant S; Ellis, Mark A; Lewis, Erica J; Waite, Brandee L; Lissoway, John; Chan, Garrett K; Krabak, Brian J

2014-12-01

Friction foot blisters are a common injury occurring in up to 39% of marathoners, the most common injury in adventure racing, and represent more than 70% of medical visits in multi-stage ultramarathons. The goal of the study was to determine whether paper tape could prevent foot blisters in ultramarathon runners. This prospective randomized trial was undertaken during RacingThePlanet 155-mile (250-km), 7-day self-supported ultramarathons in China, Australia, Egypt, Chile, and Nepal in 2010 and 2011. Paper tape was applied prerace to one randomly selected foot, with the untreated foot acting as the own control. The study end point was development of a hot spot or blister on any location of either foot. One hundred thirty-six participants were enrolled with 90 (66%) having completed data for analysis. There were 36% women, with a mean age of 40 ± 9.4 years (range, 25-40 years) and pack weight of 11 ± 1.8 kg (range, 8-16 kg). All participants developed blisters, with 89% occurring by day 2 and 59% located on the toes. No protective effect was observed by the intervention (47 versus 35; 52% versus 39%; P = .22), with fewer blisters occurring around the tape on the experimental foot than under the tape (23 vs 31; 25.6% versus 34.4%), yet 84% of study participants when queried would choose paper tape for blister prevention in the future. Although paper tape was not found to be significantly protective against blisters, the intervention was well tolerated with high user satisfaction. Copyright © 2014 Wilderness Medical Society. Published by Elsevier Inc. All rights reserved.
The effect of topical anti blister products on the risk of friction blister formation on the foot.

PubMed

Hashmi, Farina; Kirkham, Suzanne; Nester, Christopher; Lam, Sharon

2016-08-01

Foot blisters are a common injury, which can impact on activity and lead to infection. Increased skin surface hydration has been identified as a risk factor for blister formation, indicating that a reduction in hydration could reduce the risk of blister. Thirty healthy adults were randomised into 3 groups, each receiving a preventative foot blister treatment (2Toms(®) Blister Shield(®); Flexitol(®) Blistop and Boots Anti-Perspirant Foot Spray). Cycles of compression and shear loads where applied to heel skin using a mechanism driven by compressed air. Temperature changes were measured during load application using a thermal imaging camera (FLIR Systems Inc. and Therm CAM™ Quick Report). Near surface hydration of the skin was measured using a Corneometer(®) (C & K, Germany). There was no significant difference in the rate of temperature change of the skin between the three groups compared to not using products (p = 0.767, p = 0.767, p = 0.515) or when comparing each product (p = 0.551). There was a significant decrease in near surface skin hydration, compared to baseline, after the application of powder (-8.53 AU, p = 0.01). There was no significant difference in hydration after the application of film former and antiperspirant (-1.47 AU, p = 0.26; -1.00 AU, p = 0.80, respectively). With the application of external load we found no significant difference in the effect of the three products on temperature change. The powder product demonstrated an effect on reducing the risk of blister. It is postulated that powder may have a barrier effect. Crown Copyright © 2016. Published by Elsevier Ltd. All rights reserved.
Laser-driven high-frequency vibrations of metal blister surface

NASA Astrophysics Data System (ADS)

Kononenko, T. V.; Sinyavsky, M. N.; Konov, V. I.; Sentis, M.

2013-09-01

Time-resolved interferometric microscopy was applied to investigate laser-induced blistering of a titanium film on a silica substrate. Ablation of the titanium/silica interface by single 0.7 ns pulses within a certain fluence range results in local exfoliation of the metal film from the substrate avoiding, however, complete film destruction. Time-dependent transformation of the metal surface profile was reconstructed from the interference patterns within 0-13 ns time delay range. Transverse annular waves with typical amplitude of one hundred of nanometers and estimated traveling speed of few kilometers per second were revealed on the blister surface. The wave occurrence was attributed to fast inhomogeneous bending of the film covering the expanding blister. The resultant high-frequency (˜1 GHz) vibrations of the metal surface provide intensive inertial forces when such metalized target is used for blister-based laser-induced forward transfer of nanopowders and organic molecules.
The climatic distribution of blister rust on white pine in Wisconsin

Treesearch

E.P. Van Arsdel; A.J. Riker; T.F. Kouba; V.E. Suomi; R.A. Bryson

1961-01-01

White pine blister rust limits the reproduction of white pine in many areas by killing young trees. In other extensive areas unjustified fear of the disease limits white pine planting. An ability to differentiate the sites on which white pine blister rust (caused by Cronartium ribicola Fischer) might be serious from those on which the disease might...
Biology and pathology of Ribes and their implications for management of white pine blister rust

Treesearch

P. J. Zambino

2010-01-01

Ribes (currants and gooseberries) are telial hosts for the introduced and invasive white pine blister rust fungus, Cronartium ribicola. Knowledge of wild and introduced Ribes helps us understand the epidemiology of blister rust on its aecial hosts, white pines, and develop disease control and management strategies. Ribes differ by species in their contribution to...
Current and future molecular approaches to investigate the white pine blister rust pathosystem

Treesearch

B. A. Richardson; A. K. M. Ekramoddoulah; J.-J. Liu; M.-S. Kim; N. B. Klopfenstein

2010-01-01

Molecular genetics is proving to be especially useful for addressing a wide variety of research and management questions on the white pine blister rust pathosystem. White pine blister rust, caused by Cronartium ribicola, is an ideal model for studying biogeography, genetics, and evolution because: (1) it involves an introduced pathogen; (2) it includes multiple primary...
Frequency of comandra blister rust infection episodes on lodgepole pine

Treesearch

William R. Jacobi; Brian W. Geils; Jane E. Taylor

2002-01-01

Comandra blister rust is a damaging canker disease of lodgepole pine in the Central Rocky Mountains. Our knowledge of previous blister rust outbreaks and the effects of weather and climate on rust epidemiology has not been sufficient to explain the frequency and severity of disease outbreaks. Thus, we sought to describe the seasonal and annual frequency and duration of...
White pine blister rust resistance of 12 western white pine families at three field sites in the Pacific Northwest

Treesearch

Richard A. Sniezko; Robert Danchok; Jim Hamlin; Angelia Kegley; Sally Long; James Mayo

2012-01-01

Western white pine (Pinus monticola Douglas ex D. Don) is highly susceptible to the non-native, invasive pathogen Cronartium ribicola, the causative agent of white pine blister rust. The susceptibility of western white pine to blister rust has limited its use in restoration and reforestation throughout much of western North...
Screening conventional fungicides...control of blister rust on sugar pine in California

Treesearch

Clarence R. Quick

1967-01-01

After 5 years, 4 of 14 fungicides tested showed varying pr of development into satisfactory direct control of blister rust. Little promise of systemic control was found. Trees treated were second-growth sugar pine in a mixed conifer forest in eastern Shasta County, California, where blister rust has been intensifying for many years. Most trees received basal-stem...
Demonstration of Smart Fluorescent and Self-Healing Coatings for Severely Corrosive Environments at Vehicle Wash Facilities

DTIC Science & Technology

2009-08-01

as well as pipe and tank exteriors providing early detection of coating erosion, cracks , and intercoat blistering. A fluorescing coating used ERDC...poor with widespread areas of peeling and cracking on the exterior siding. Areas of exposed galvanizing were rusting. Structural steel elements...and application of TT-P-86 Type 2 red lead paint and red and white colored alkyd enamel topcoats. The average dry film thickness on the exterior
Influence of an antiperspirant on foot blister incidence during cross-country hiking.

PubMed

Knapik, J J; Reynolds, K; Barson, J

1998-08-01

Rubbing moist skin results in higher frictional forces than rubbing very dry skin. As friction increases, the probability of activity-related blisters also increases. Therefore reducing moisture may reduce blister incidence during physical activity. We examined whether an antiperspirant can reduce foot blisters during hiking. In a double-blind study, cadets attending the US Military Academy were separated into two groups that used either an antiperspirant (20% aluminum chloride hexahydrate in anhydrous ethyl alcohol) or placebo (anhydrous ethyl alcohol) preparation. Cadets were told to apply preparations to their feet for 5 consecutive nights. On day 6, cadets completed a 21-km hike, and their feet were examined for blisters before and after. Because of dropouts, the final sample size was 667 cadets with 328 in the antiperspirant group and 339 in the placebo group. There was a high rate of noncompliance with the treatment schedule: Cadets used the preparations from 0 to 5 nights before the hike. For cadets using the preparations at least 3 nights before the hike (n=269), the incidence of foot blisters was 21% for the antiperspirant group and 48% for the placebo group (P < 0.01). However, reports of skin irritation were 57% for the antiperspirant group and 6% for the placebo group (P < 0.01). A 20% solution of aluminum chloride hexahydrate in anhydrous ethyl alcohol may be effective in reducing foot blisters during hiking; however, the side effect of skin irritation should be considered and preventive measures studied to reduce this irritation.
Autoantibodies in the Autoimmune Disease Pemphigus Foliaceus Induce Blistering via p38 Mitogen-Activated Protein Kinase-Dependent Signaling in the Skin

PubMed Central

Berkowitz, Paula; Chua, Michael; Liu, Zhi; Diaz, Luis A.; Rubenstein, David S.

2008-01-01

Pemphigus foliaceus (PF) is a human autoimmune blistering disease in which a humoral immune response targeting the skin results in a loss of keratinocyte cell-cell adhesion in the superficial layers of the epidermal epithelium. In PF, desmoglein-1-specific autoantibodies induce blistering. Evidence is beginning to accumulate that activation of signaling may have an important role in the ability of pathogenic pemphigus IgGs to induce blistering and that both p38 mitogen-activated protein kinase (MAPK) and heat shock protein (HSP) 27 are part of this signaling pathway. This study was undertaken to investigate the ability of PF IgGs to activate signaling as well as the contribution of this signaling pathway to blister induction in an in vivo model of PF. Phosphorylation of both p38 MAPK and HSP25, the murine HSP27 homolog, was observed in the skin of PF IgG-treated mice. Furthermore, inhibition of p38 MAPK blocked the ability of PF IgGs to induce blistering in vivo. These results indicate that PF IgG-induced blistering is dependent on activation of p38 MAPK in the target keratinocyte. Rather than influencing the immune system, limiting the autoantibody-induced intracellular signaling response that leads to target end-organ damage may be a more viable therapeutic strategy for the treatment of autoimmune diseases. Inhibition of p38 MAPK may be an effective strategy for the treatment of PF. PMID:18988808
Restoration and management of eastern white pine within high blister rust hazard zones in the Lake States

Treesearch

S. A. Katovich; J. G. O' Brien; M. E. Mielke; M. E. Ostry

2004-01-01

In areas considered high hazard for blister rust in the northern Lake States, six white pine plantings were established between 1989 and 1999 to: (1) evaluate the impacts of blister rust, white pine weevil, browsing, and competition stress on tree growth and survival, and (2) evaluate the effectiveness of genetic and silvicultural strategies to minimize damage. The...
White pine blister rust in Korea, Japan and other Asian regions: comparisons and implications for North America

Treesearch

M.-S. Kim; N. B. Klopfenstein; Y. Ota; S. K. Lee; K.-S. Woo; S. Kaneko

2010-01-01

This article briefly reviews the history of white pine blister rust, attributed to Cronartium ribicola, and addresses current research and management issues in South Korea, Japan and other regions of eastern Asia (China, Russia and Himalaya). For each region, the distribution, damage, aecial hosts, telial hosts and management of C. ribicola and other blister rust fungi...
Strategies for managing whitebark pine in the presence of white pine blister rust [Chapter 17

Treesearch

Raymond J. Hoff; Dennis E. Ferguson; Geral I. McDonald; Robert E. Keane

2001-01-01

Whitebark pine (Pinus albicaulis) is one of many North American white pine species (Pinus subgenus Strobus) susceptible to the fungal disease white pine blister rust (Cronartium ribicola). Blister rust has caused severe mortality (often reaching nearly 100 percent) in many stands of white bark pine north of 45Â° latitude in western North America. The rust is slowly...

Blister rust in North America: What we have not learned in the past 100 years

Treesearch

Eugene P. Van Arsdel; Brian W. Geils

2011-01-01

Introduction of Cronartium ribicola (white pine blister rust) greatly motivated development of tree disease control and research in America. Although foresters and pathologists have learned much in the past 100 years, more remains to learn. The most important lesson is that fear of blister rust has reduced pine regeneration more than the disease itself. Based on six...
A preliminary hazard model of white pine blister rust for the Sacramento Ranger District, Lincoln National Forest

Treesearch

Brian W. Geils; David A. Conklin; Eugene P. van Arsdel

1999-01-01

Blister rust, caused by the introduced fungus Cronartium ribicola, is a serious disease of white pines in North America. Since about 1970, an outbreak has been increasing in the Sacramento Mountains of southern New Mexico and threatens southwestern white pine. To help determine the expected extent and impact of blister rust, we propose a preliminary...
[Application of blistering cupping].

PubMed

Gu, Xingui; Chen, Zelin; Chen, Bo; Fan, Yihua; Chen, Xianghong

2016-11-12

Blistering cupping is special as eliminating wind and dampness as well as removing phlegm and blood stasis, and it achieves effects through suction. In this paper we reviewed relevant literature combined with clinical experience so as to summarize its operation attention through exploring the origin, mechanism and application. We divide the progress into the blistering period, the phlegm-stasis-eliminating period, and the escharosis period according to the changes of bubble and the things pulled out. Blistering cupping creates ways to eliminate concrete unhealthy influences through smoothing meridians and collaterals, such as phlegm and retained fluid, dampness and blood stasis. Thus chronic diseases are relieved. Also,we propose the rules of "blistering acupoints being related to disease location as well as the nature of acupoints and diseases". The therapy has been used to treat diseases of respiratory system, osteoarticular, skin and subcutaneous tissue, mental and behavioral disorders, and tumor, among which the effects of intractable diseases of respiratory and osteoarticular systems are definite. It deserves to be further explored and promoted.
HOW to Manage Eastern White Pine to Minimize Damage from Blister Rust and White Pine Weevil

Treesearch

Steven Katovich; Manfred E. Mielke

1993-01-01

White pine was once a dominant forest species in the north central and northeastern United States. Following logging in the late 1800's and the early part of this century, two major pests, white pine blister rust, Cronartium ribicola J.C.Fisch., and white pine weevil, Pissodes strobi (Peck), combined to reduce the value of white pine. Blister rust was introduced...
Apparatus Tests Peeling Of Bonded Rubbery Material

NASA Technical Reports Server (NTRS)

Crook, Russell A.; Graham, Robert

1996-01-01

Instrumented hydraulic constrained blister-peel apparatus obtains data on degree of bonding between specimen of rubbery material and rigid plate. Growth of blister tracked by video camera, digital clock, pressure transducer, and piston-displacement sensor. Cylinder pressure controlled by hydraulic actuator system. Linear variable-differential transformer (LVDT) and float provide second, independent measure of change in blister volume used as more precise volume feedback in low-growth-rate test.
Effect of litter quality on foot pad dermatitis, hock burns and breast blisters in broiler breeders during the production period.

PubMed

Kaukonen, Eija; Norring, Marianna; Valros, Anna

2016-12-01

Foot pad dermatitis and hock burn lesions are a form of contact dermatitis, a condition affecting skin areas in contact with unsuitable or irritating material. Contact dermatitis is a common problem, reducing the welfare of broilers, and is believed to also affect broiler breeders. However, there is very little research on contact dermatitis in breeders. This study followed the severity of foot pad lesions in broiler breeders throughout the production period. At slaughter the presence of hock burns and breast blisters was also determined. In addition, changes in litter condition over time and the impact of litter quality on foot pads were evaluated. The study was performed on 10 broiler breeder farms, including altogether 18 flocks. Foot pads of 100 hens per flock were assessed at the end of rearing period, three times during the production period, and at slaughter. Foot pad and hock lesions, as well as litter condition were scored on a 5-point scale. Litter quality was evaluated as pH, moisture and ammonia content. The condition of foot pads deteriorated towards slaughter age, with the occurrence of severe lesions reaching a maximum of 64% on average at slaughter. Hock lesions and breast blisters were rare. The litter layer became drier over time. Although poorer litter condition and wetness influenced foot pad health negatively, the effect on severe lesions was not significant. We also observed a negative effect on foot pad condition of larger slat areas. In conclusion, maintaining good litter quality alone is not enough to ensure healthy foot pads in broiler breeders.
The relative contributions of disease and insects in the decline of a long-lived tree: a stochastic demographic model of whitebark pine (Pinus albicaulis)

USGS Publications Warehouse

Jules, Erik S; Jackson, Jenell I.; van Mantgem, Phillip J.; Beck, Jennifer S.; Murray, Michael P.; Sahara, E. April

2016-01-01

Pathogens and insect pests have become increasingly important drivers of tree mortality in forested ecosystems. Unfortunately, understanding the relative contributions of multiple mortality agents to the population decline of trees is difficult, because it requires frequent measures of tree survival, growth, and recruitment, as well as the incidence of mortality agents. We present a population model of whitebark pine (Pinus albicaulis), a high-elevation tree undergoing rapid decline in western North America. The loss of whitebark pine is thought to be primarily due to an invasive pathogen (white pine blister rust; Cronartium ribicola) and a native insect (mountain pine beetle; Dendroctonus ponderosae). We utilized seven plots in Crater Lake National Park (Oregon, USA) where 1220 trees were surveyed for health and the presence of blister rust and beetle activity annually from 2003–2014, except 2008. We constructed size-based projection matrices for nine years and calculated the deterministic growth rate (λ) using an average matrix and the stochastic growth rate (λs) by simulation for whitebark pine in our study population. We then assessed the roles of blister rust and beetles by calculating λ and λsusing matrices in which we removed trees with blister rust and, separately, trees with beetles. We also conducted life-table response experiments (LTRE) to determine which demographic changes contributed most to differences in λ between ambient conditions and the two other scenarios. The model suggests that whitebark pine in our plots are currently declining 1.1% per year (λ = 0.9888, λs = 0.9899). Removing blister rust from the models resulted in almost no increase in growth (λ = 0.9916, λs = 0.9930), while removing beetles resulted in a larger increase in growth (λ = 1.0028, λs = 1.0045). The LTRE demonstrated that reductions in stasis of the three largest size classes due to beetles contributed most to the smaller λ in the ambient condition. Our work demonstrates a method for assessing the relative effects of different mortality agents on declining tree populations, and it shows that the effects of insects and pathogens can be markedly different from one another. In our study, beetle activity significantly reduced tree population growth while a pathogen had minimal effect, thus management actions to stabilize our study population will likely need to include reducing beetle activity.
Topical Modulation of the Burn Wound Inflammatory Response to Improve Short and Long Term Outcomes

DTIC Science & Technology

2017-10-01

casualty, treatment, organ failure, systemic inflammatory response syndrome , thermal injury, wound model, intervention 3. ACCOMPLISHMENTS: What...thickness burns have a blister response. Using human eye or H&E studies, we did not observe any blisters in the pig model. However, the OCT...the deeper the partial thickness burn, the bigger the blister, until it gets close to full-thickness burns. The full-thickness burns are dry and
Blister rust resistance among 19 families of whitebark pine, Pinus albicaulis, from Oregon and Washington – early results from an artificial inoculation trial

Treesearch

Angelia Kegley; Richard A. Sniezko; Robert Danchok; Douglas P. Savin

2012-01-01

Whitebark pine is considered one of the most susceptible white pine species to white pine blister rust, the disease caused by the non-native pathogen Cronartium ribicola. High mortality from blister rust and other factors in much of the range in the United States and Canada have raised serious concerns about the future viability of this high-...
Characterization of Blistering and Delamination in Depleted Uranium Hohlraums

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biobaum, K. J. M.

2013-03-01

Blistering and delamination are the primary failure mechanisms during the processing of depleted uranium (DU) hohlraums. These hohlraums consist of a sputter-deposited DU layer sandwiched between two sputter-deposited layers of gold; a final thick gold layer is electrodeposited on the exterior. The hohlraum is deposited on a copper-coated aluminum mandrel; the Al and Cu are removed with chemical etching after the gold and DU layers are deposited. After the mandrel is removed, blistering and delamination are observed on the interiors of some hohlraums, particularly at the radius region. It is hypothesized that blisters are caused by pinholes in the coppermore » and gold layers; etchant leaking through these holes reaches the DU layer and causes it to oxidize, resulting in a blister. Depending on the residual stress in the deposited layers, blistering can initiate larger-scale delamination at layer interfaces. Scanning electron microscopy indicates that inhomogeneities in the machined aluminum mandrel are replicated in the sputter-deposited copper layer. Furthermore, the Cu layer exhibits columnar growth with pinholes that likely allow etchant to come in contact with the gold layer. Any inhomogeneities or pinholes in this initial gold layer then become nucleation sites for blistering. Using a focused ion beam system to etch through the gold layer and extract a cross-sectional sample for transmission electron microscopy, amorphous, intermixed layers at the gold/DU interfaces are observed. Nanometer-sized bubbles in the sputtered and electrodeposited gold layers are also present. Characterization of the morphology and composition of the deposited layers is the first step in determining modifications to processing parameters, with the goal of attaining a significant improvement in hohlraum yield.« less
Long-term pulmonary complications of chemical warfare agent exposure in Iraqi Kurdish civilians.

PubMed

Ghanei, Mostafa; Naderi, Mostafa; Kosar, Ali Morad; Harandi, Ali Amini; Hopkinson, Nicholas S; Poursaleh, Zohreh

2010-08-01

The Iraqi government used a range of chemical weapons, including blistering and nerve agents, against Iraqi Kurdish civilians in the 1980s. Few data exist about the long-term respiratory consequences of this exposure. In this study, Kurdish subjects with a history of exposure to chemical weapons were invited to attend a clinical assessment, including a review of their history, physical examination, and a high-resolution computed tomography (CT) of the thorax. Blistering at the time of exposure was used to define significant exposure to mustard gas. Results were compared between two groups of blistering and nonblistering. Four hundred seventy-nine subjects were studied; 45.7% male and 54.3% female. The mean age and standard deviation (mean +/- SD) of the cases was 43.1 +/- 13.7. Spirometry was abnormal in 15.2% of subjects and air trapping was present on CT scan in 46.6% and did not differ between patients with (n = 278) or without a history of blistering. Respiratory symptoms, including dyspnea, cough, and sputum production, were more common in subjects with a history of blistering (all p < .005) and blistering was also associated with a lower forced expiratory volume in one second (FEV(1)) (p < .0001). Severe complications were most common in subjects from Halabja who also made up the majority of participants. These results show that objective abnormalities are common in people with symptoms attributed to prior exposure to chemical agent. Blistering at the time of exposure was associated with more respiratory symptoms and worse lung function, but not with CT appearances. The high proportion of severe cases in comparison to reports from Iran may reflect the historical absence of effective early treatment, including strategies to reduce prolonged early exposure in this population.
Draft genomes of two blister beetles Hycleus cichorii and Hycleus phaleratus

PubMed Central

Wu, Yuan-Ming; Li, Jiang

2018-01-01

Abstract Background Commonly known as blister beetles or Spanish fly, there are more than 1500 species in the Meloidae family (Hexapoda: Coleoptera: Tenebrionoidea) that produce the potent defensive blistering agent cantharidin. Cantharidin and its derivatives have been used to treat cancers such as liver, stomach, lung, and esophageal cancers. Hycleus cichorii and Hycleus phaleratus are the most commercially important blister beetles in China due to their ability to biosynthesize this potent vesicant. However, there is a lack of genome reference, which has hindered development of studies on the biosynthesis of cantharidin and a better understanding of its biology and pharmacology. Results We report 2 draft genomes and quantified gene sets for the blister beetles H. cichorii and H. phaleratus, 2 complex genomes with >72% repeats and approximately 1% heterozygosity, using Illumina sequencing data. An integrated assembly pipeline was performed for assembly, and most of the coding regions were obtained. Benchmarking universal single-copy orthologs (BUSCO) assessment showed that our assembly obtained more than 98% of the Endopterygota universal single-copy orthologs. Comparison analysis showed that the completeness of coding genes in our assembly was comparable to other beetle genomes such as Dendroctonus ponderosae and Agrilus planipennis. Gene annotation yielded 13 813 and 13 725 protein-coding genes in H. cichorii and H. phaleratus, of which approximately 89% were functionally annotated. BUSCO assessment showed that approximately 86% and 84% of the Endopterygota universal single-copy orthologs were annotated completely in these 2 gene sets, whose completeness is comparable to that of D. ponderosae and A. planipennis. Conclusions Assembly of both blister beetle genomes provides a valuable resource for future biosynthesis of cantharidin and comparative genomic studies of blister beetles and other beetles. PMID:29444297
Draft genomes of two blister beetles Hycleus cichorii and Hycleus phaleratus.

PubMed

Wu, Yuan-Ming; Li, Jiang; Chen, Xiang-Sheng

2018-03-01

Commonly known as blister beetles or Spanish fly, there are more than 1500 species in the Meloidae family (Hexapoda: Coleoptera: Tenebrionoidea) that produce the potent defensive blistering agent cantharidin. Cantharidin and its derivatives have been used to treat cancers such as liver, stomach, lung, and esophageal cancers. Hycleus cichorii and Hycleus phaleratus are the most commercially important blister beetles in China due to their ability to biosynthesize this potent vesicant. However, there is a lack of genome reference, which has hindered development of studies on the biosynthesis of cantharidin and a better understanding of its biology and pharmacology. We report 2 draft genomes and quantified gene sets for the blister beetles H. cichorii and H. phaleratus, 2 complex genomes with >72% repeats and approximately 1% heterozygosity, using Illumina sequencing data. An integrated assembly pipeline was performed for assembly, and most of the coding regions were obtained. Benchmarking universal single-copy orthologs (BUSCO) assessment showed that our assembly obtained more than 98% of the Endopterygota universal single-copy orthologs. Comparison analysis showed that the completeness of coding genes in our assembly was comparable to other beetle genomes such as Dendroctonus ponderosae and Agrilus planipennis. Gene annotation yielded 13 813 and 13 725 protein-coding genes in H. cichorii and H. phaleratus, of which approximately 89% were functionally annotated. BUSCO assessment showed that approximately 86% and 84% of the Endopterygota universal single-copy orthologs were annotated completely in these 2 gene sets, whose completeness is comparable to that of D. ponderosae and A. planipennis. Assembly of both blister beetle genomes provides a valuable resource for future biosynthesis of cantharidin and comparative genomic studies of blister beetles and other beetles.
Recovery plan for Scots pine blister rust caused by Cronartium flaccidum (Alb. & Schwein.) G. Winter and Peridermium pini (Pers.) Lév. [syn. C. asclepiadeum (Willd.) Fr., Endocronartium pini (Pers.) Y. Hiratsuka

Treesearch

Brian W. Geils; Ned B. Klopfenstein; Mee-Sook Kim; Pauline Spaine; Bryce A. Richardson; Paul J. Zambino; Charles G. Shaw; James Walla; Russ Bulluck; Laura Redmond; Kent Smith

2009-01-01

The sexually reproducing form of Scots pine blister rust, C. flaccidum, completes its life cycle alternating between pines of the subgenus Pinus and seed-plants of various families. Scots pine blister rust is also caused by a form of the rust that spreads directly from pine to pine and is named, Peridermium pini...
Vesiculobullous lesions in lipoid proteinosis: a case report.

PubMed

Rao, Raghavendra; Prabhu, Smitha Smitha; Sripathi, H; Gupta, Sachi

2008-07-15

Vesiculobullous disorders in a child can be a diagnostic challenge. Common causes of blisters in early childhood include genodermatoses like epidermolysis bullosa and infections like herpes simplex. Lipoid proteinosis may rarely present with vesiculobullous lesions in childhood. We report a child, who presented in early childhood with blistering dermatosis. On long term follow-up, typical features of lipoid proteinosis developed. A high index of suspicion is required when one deals with blistering dermatosis in a child.
Autoantibody Signaling in Pemphigus Vulgaris: Development of an Integrated Model

PubMed Central

Sajda, Thomas; Sinha, Animesh A.

2018-01-01

Pemphigus vulgaris (PV) is an autoimmune skin blistering disease effecting both cutaneous and mucosal epithelia. Blister formation in PV is known to result from the binding of autoantibodies (autoAbs) to keratinocyte antigens. The primary antigenic targets of pathogenic autoAbs are known to be desmoglein 3, and to a lesser extent, desmoglein 1, cadherin family proteins that partially comprise the desmosome, a protein structure responsible for maintaining cell adhesion, although additional autoAbs, whose role in blister formation is still unclear, are also known to be present in PV patients. Nevertheless, there remain large gaps in knowledge concerning the precise mechanisms through which autoAb binding induces blister formation. Consequently, the primary therapeutic interventions for PV focus on systemic immunosuppression, whose side effects represent a significant health risk to patients. In an effort to identify novel, disease-specific therapeutic targets, a multitude of studies attempting to elucidate the pathogenic mechanisms downstream of autoAb binding, have led to significant advancements in the understanding of autoAb-mediated blister formation. Despite this enhanced characterization of disease processes, a satisfactory explanation of autoAb-induced acantholysis still does not exist. Here, we carefully review the literature investigating the pathogenic disease mechanisms in PV and, taking into account the full scope of results from these studies, provide a novel, comprehensive theory of blister formation in PV. PMID:29755451
MAPKAP kinase 2 (MK2)-dependent and independent models of blister formation in pemphigus vulgaris

PubMed Central

Mao, Xuming; Li, Hong; Sano, Yasuyo; Gaestel, Matthias; Park, Jin Mo; Payne, Aimee S.

2013-01-01

Pemphigus vulgaris (PV) is an autoimmune blistering disease characterized by autoantibodies to the keratinocyte adhesion protein desmoglein (Dsg) 3. Previous studies suggest that PV pathogenesis involves p38 mitogen activated protein kinase-dependent and -independent pathways. However, p38 is a difficult protein to study and therapeutically target because it has four isoforms and multiple downstream effectors. In the current study, we identify MAPKAP kinase 2 (MK2) as a downstream effector of p38 signaling in PV and describe MK2-dependent and -independent mechanisms of blister formation using passive transfer of human anti-Dsg IgG4 mAbs to neonatal mice. In human keratinocytes, PV mAbs activate MK2 in a dose-dependent manner. MK2 is also activated in human pemphigus skin blisters, causing translocation of MK2 from the nucleus to the cytosol. Small molecule inhibition of MK2 and silencing of MK2 expression block PV mAb-induced Dsg3 endocytosis in human keratinocytes. Additionally, small molecule inhibition and genetic deletion of p38α and MK2 inhibit spontaneous, but not induced, suprabasal blisters by PV mAbs in mouse passive transfer models. Collectively, these data suggest that MK2 is a key downstream effector of p38 that can modulate PV autoantibody pathogenicity. MK2 inhibition may be a valuable adjunctive therapy for control of pemphigus blistering. PMID:23657501
Effects of ridge cracking and interface sliding on morphological symmetry breaking in straight-sided blisters

NASA Astrophysics Data System (ADS)

Li, Shi-Chen; Yu, Sen-Jiang; He, Linghui; Ni, Yong

2018-03-01

Complex surface patterns generated by nonlinear buckling originate from various symmetry-breaking instabilities. Identifying possible key factors that regulate the instability modes is critical to reveal the mechanism of the surface pattern selection. In this paper, how another two factors (ridge cracking and interface sliding) including Poisson's ratio influence the morphological symmetry breaking in straight-sided blisters are systematically studied. Morphology diagrams from stability analysis show that ridge cracking and low Poisson's ratio promote symmetric instability mode and favor bubble-like blisters while interface sliding and high Poisson's ratio facilitate antisymmetric instability mode and result in telephone cord buckles. The analytical predictions are evidenced by experimental observations on annealed silicon nitride films on glass substrates and confirmed by nonlinear numerical simulations. This study explains how and why the rarely observed bubble-like blisters in accompany with ridge crack can appear in brittle thin films in comparison with the ubiquitously observed telephone cord buckles that usually form as the development of an antisymmetric instability mode when straight-sided blisters undergo the super-critical isotropic compression.
BP180 Is Critical in the Autoimmunity of Bullous Pemphigoid

PubMed Central

Liu, Yale; Li, Liang; Xia, Yumin

2017-01-01

Bullous pemphigoid (BP) is by far the most common autoimmune blistering dermatosis that mainly occurs in the elderly. The BP180 is a transmembrane glycoprotein, which is highly immunodominant in BP. The structure and location of BP180 indicate that it is a significant autoantigen and plays a key role in blister formation. Autoantibodies from BP patients react with BP180, which leads to its degradation and this has been regarded as the central event in BP pathogenesis. The consequent blister formation involves the activation of complement-dependent or -independent signals, as well as inflammatory pathways induced by BP180/anti-BP180 autoantibody interaction. As a multi-epitope molecule, BP180 can cause dermal–epidermal separation via combining each epitope with specific immunoglobulin, which also facilitates blister formation. In addition, some inflammatory factors can directly deplete BP180, thereby leading to fragility of the dermal–epidermal junction and blister formation. This review summarizes recent investigations on the role of BP180 in BP pathogenesis to determine the potential targets for the treatment of patients with BP. PMID:29276517
Study on thickness distribution of thermoformed medical PVC blister

NASA Astrophysics Data System (ADS)

Li, Yiping

2017-08-01

Vacuum forming has many advantages over other plastic forming processes due to its cost effectiveness, time efficiency, higher product precision, and more design flexibility. Nevertheless, when pressures greater than the atmospheric value are required to force the thermo-plastic into more intimate contact with the mold surface, pressure forming is a better choice. This paper studies the process of air-pressure thermoforming of plastic sheet, and focuses on medical blister PVC products. ANSYS POLYFLOW tool is used to simulate the process and analyze the wall thickness distribution of the blister. The influence of mold parameters on the wall thickness distribution of thermoformed part is thus obtained through simulation. Increasing radius between mold and side wall at the bottom of blister and draft prove to improve the wall thickness distribution.

Lionfish envenomation of the hand.

PubMed

Patel, M R; Wells, S

1993-05-01

Lionfish (Pterois volitans) envenomation of the hand causes excruciating pain and occurs in three grades: (1) erythematous reaction, (2) blister formation, and (3) dermal necrosis. The initial treatment in all cases is to soak the hand in nonscalding water (45 degrees C) until the pain subsides by denaturing the thermolabile venom proteins. The blisters should be immediately excised to prevent dermal necrosis, inasmuch as the blister fluid contains residual active venom. To prevent a hypersensitivity reaction, any further contact with the fish should be avoided.
Blistering of Graphite/Polymer Composites Galvanically Coupled with Metals in Sea Water

DTIC Science & Technology

1993-01-01

pressure Vi = molar volume of species T Yi = activity coefficient for species T (p = electrical potential Using the flux definition, the conservation...at = aJi/ax ...(11) (b) determine the rate of volume increase of water Vw’ cm3 1s in the blister cavity by the following expression: Vw’ = iVw/at = 1a...induced in the polymer and the fiber/matrix interface region due to the above volume change: The volume increase of the fluid in blister given by
Blisters: First Aid

MedlinePlus

... healthy traveler. In: Mayo Clinic Guide to Self-Care. 7th ed. Rochester, Minn.: Mayo Foundation for Medical Education and Research; 2017. Brennan FH. Treatment and prevention of foot friction blisters. ACSM's Health & Fitness Journal. 2013;17: ...
Poison Ivy/Oak/Sumac

MedlinePlus

... burning, or blistering. Severe, widespread rashes require medical treatment. Signs and Symptoms an itchy red rash that appears within 4 hours to 4 days after touching the plant oil blisters that ooze clear fluid bumps and ...
Skin blister formation together with patterned intradermal hematoma: a special type of tire mark injury in victims run over by a wheel.

PubMed

Pircher, R; Epting, T; Schmidt, U; Geisenberger, D; Pollak, S; Kramer, L

2015-04-01

A traffic accident victim run over by a vehicle may show a patterned skin hematoma reflecting the grooves of the tire's profile. Apart from this well-known type of imprint mark, the affected skin can also be blistered provided that the wheel exerts high pressure on the body for a prolonged period of time. The macro- and micromorphological findings as well as the protein composition of the blister fluid were investigated on the basis of a relevant autopsy case. Analogous to blisters associated with hanging marks, the transudation of serous fluid with consecutive detachment of the epidermis is interpreted as a pressure-related effect which cannot be regarded as a sign of vitality. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.
Undercoat prevents blistering of silver plating at elevated temperatures

NASA Technical Reports Server (NTRS)

Kuster, C. A.

1967-01-01

Gold undercoat prevents blistering in the silver plating of Inconel 718 seals from steam at high temperatures. The undercoat is diffused into the surface of the parent metal by baking prior to silver plating.
U-Mo Plate Blister Anneal Interim Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Francine J. Rice; Daniel M. Wachs; Adam B. Robinson

2010-10-01

Blister thresholds in fuel elements have been a longstanding performance parameter for fuel elements of all types. This behavior has yet to be fully defined for the RERTR U-Mo fuel types. Blister anneal studies that began in 2007 have been expanded to include plates from more recent RERTR experiments. Preliminary data presented in this report encompasses the early generations of the U-Mo fuel systems and the most recent but still developing fuel system. Included is an overview of relevant dispersion fuel systems for the purposes of comparison.
Autoimmune Subepidermal Bullous Diseases of the Skin and Mucosae: Clinical Features, Diagnosis, and Management.

PubMed

Amber, Kyle T; Murrell, Dedee F; Schmidt, Enno; Joly, Pascal; Borradori, Luca

2018-02-01

Autoimmune subepidermal blistering diseases of the skin and mucosae constitute a large group of sometimes devastating diseases, encompassing bullous pemphigoid, gestational pemphigoid, mucous membrane pemphigoid, epidermolysis bullosa acquisita, and anti-p200 pemphigoid. Their clinical presentation is polymorphic. These autoimmune blistering diseases are associated with autoantibodies that target distinct components of the basement membrane zone of stratified epithelia. These autoantigens represent structural proteins important for maintenance of dermo-epidermal integrity. Bullous pemphigoid (BP) is the most common subepidermal autoimmune blistering disease of the skin and mucosae. Although the disease typically presents with a generalized blistering eruption associated with itch, atypical variants with either localized bullous lesions or "non-bullous" presentations are observed in approximately 20% of patients. A peculiar form of BP typically associated with pregnancy is pemphigoid gestationis. In anti-p200 pemphigoid, patients present with tense blisters on erythematosus or normal skin resembling BP, with a predilection for acral surfaces. These patients have antibodies targeting the 200-kDa basement membrane protein. Epidermolysis bullosa is a rare autoimmune blistering disease associated with autoantibodies against type VII collagen that can have several phenotypes including a classical form mimicking dystrophic epidermolysis bullosa, an inflammatory presentation mimicking BP, or mucous membrane pemphigoid-like lesions. Mucous membrane pemphigoid (MMP) is the term agreed upon by international consensus for an autoimmune blistering disorder, which affects one or more mucous membrane and may involve the skin. The condition involves a number of different autoantigens in the basement membrane zone. It may result in severe complications from scarring, such as blindness and strictures. Diagnosis of these diseases relies on direct immunofluorescence microscopy studies and immunoserological assays. Management of affected patients is often challenging. We will here review the clinical and immunopathological features as well as the pathophysiology of this group of organ-specific autoimmune diseases. Finally, we will discuss the diagnostic approach and the principles of management in clinical practice.
Monitoring direct and indirect climate effects on whitebark pine ecosystems at Crater Lake National park

USGS Publications Warehouse

Smith, S.B.; Odion, D.C.; Sarr, D.A.; Irvine, K.M.

2011-01-01

Whitebark pine (Pinus albicaulis) is the distinctive, often stunted, and picturesque tree line species in the American West. As a result of climate change, mountain pine beetles (Dendroctonus ponderosae) have moved up in elevation, adding to nonnative blister rust (Cronartium ribicola) disease as a major cause of mortality in whitebark pine. At Crater Lake National Park, Oregon, whitebark pine is declining at the rate of 1% per year. The Klamath Network, National Park Service, has elected to monitor whitebark pine and associated high-elevation vegetation. This program is designed to sample whitebark pine throughout the park to look for geographic patterns in its exposure to and mortality from disease and beetles. First-year monitoring has uncovered interesting patterns in blister rust distribution. Incidence of rust disease was higher on the west side of the park, where conditions are wetter and more humid than on the east side. However, correlating climate alone with rust disease is not straightforward. On the east side of the park, the odds of blister rust infection were much greater in plots having Ribes spp., shrubs that act as the alternate host for a portion of the rust's life cycle. However, on the park's west side, there was not a statistically significant increase in blister rust in plots with Ribes. This suggests that different species of Ribes associated with whitebark pine can increase pine exposure to blister rust disease. There is also convincing evidence of an association between total tree density and the incidence of blister rust. Warmer temperatures and possibly increased precipitation will affect both whitebark pine and Ribes physiology as well as tree density and mountain pine beetle numbers, all of which may interact with blister rust to cause future changes in tree line communities at Crater Lake. The Klamath Network monitoring program plans to document and study these ongoing changes.
Pigmentation Traits, Sun Exposure, and Risk of Incident Vitiligo in Women.

PubMed

Dunlap, Rachel; Wu, Shaowei; Wilmer, Erin; Cho, Eunyoung; Li, Wen-Qing; Lajevardi, Newsha; Qureshi, Abrar

2017-06-01

Vitiligo is the most common cutaneous depigmentation disorder worldwide, yet little is known about specific risk factors for disease development. Using data from the Nurses' Health Study, a prospective cohort study of 51,337 white women, we examined the associations between (i) pigmentary traits and (ii) reactions to sun exposure and risk of incident vitiligo. Nurses' Health Study participants responded to a question about clinician-diagnosed vitiligo and year of diagnosis (2001 or before, 2002-2005, 2006-2009, 2010-2011, or 2012+). We used Cox proportional hazards regression models to estimate the multivariate-adjusted hazard ratios and 95% confidence intervals of incident vitiligo associated with exposures variables, adjusting for potential confounders. We documented 271 cases of incident vitiligo over 835,594 person-years. Vitiligo risk was higher in women who had at least one mole larger than 3 mm in diameter on their left arms (hazard ratio = 1.37, 95% confidence interval = 1.02-1.83). Additionally, vitiligo risk was higher among women with better tanning ability (hazard ratio = 2.59, 95% confidence interval = 1.21-5.54) and in women who experienced at least one blistering sunburn (hazard ratio = 2.17, 95% confidence interval = 1.15-4.10). In this study, upper extremity moles, a higher ability to achieve a tan, and history of a blistering sunburn were associated with a higher risk of developing vitiligo in a population of white women. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.
Coma blisters in children: case report and review of the literature.

PubMed

Bosco, Laura; Schena, Donatella; Colato, Chiara; Biban, Paolo; Girolomoni, Giampiero

2013-12-01

Coma-induced blisters is a rare condition associated with prolonged impairment of conscious level, which is relatively well-known in adults following overdose with barbiturates. However, it has been very rarely described in children. A case of coma-bullae occurring in an 11-year-old child with meningoencephalitis is herein reported. The bullous lesions occurred on the limbs and trunks, and evolved into necrotic ulcers in a few days. No correlation with any drug overdosage was found. A skin biopsy revealed epidermal and eccrine sweat gland necrosis with abundant neutrophils, and thrombosis of the vessels in the lower dermis. A comprehensive review of the literature showed that only 5 cases of coma-bullae in children have been published so far. Coma blistering resolves spontaneously within days or weeks. Diagnosis of coma-bullae may require careful clinical-pathologic correlation to exclude other blistering diseases in children.
Junctional Epidermolysis Bullosa (Non-Herlitz Type).

PubMed

Bhinder, Munir Ahmad; Arshad, Muhammad Waqar; Zahoor, Muhammad Yasir; Shehzad, Wasim; Tariq, Muhammad; Shabbir, Muhammad Imran

2017-05-01

Junctional epidermolysis bullosa (JEB) is a recessively inherited skin blistering disease and is caused due to abnormalities in proteins that hold layers of the skin. Herlitz JEB is the severe form and non-Herlitz JEB is the milder form. This report describes a case of congenitally affected male child aged 5 years, with skin blistering. He has mitten-like hands and soft skin blistering on hands, legs and knees. Symptoms almost disappeared at the age of 3 years but reappeared with increased severity after 6 months. Histopathological examination showed epidermal detachment with intact basal cell layer and sparse infiltrate of lymphocytes with few eosinophils in the dermis. There was no blistering on the moist lining of the mouth and digestive tract. Localized symptoms with less lethality and histopathological examination indicated the presence of non-Herlitz type of JEB. This is the first report which confirms the presence of non-Herlitz junctional epidermolysis bullosa in Pakistan.
Treatment of port-wine stains with a noncoherent pulsed light source: a retrospective study.

PubMed

Raulin, C; Schroeter, C A; Weiss, R A; Keiner, M; Werner, S

1999-06-01

We investigated whether a noncoherent intense pulsed light source (IPLS) would be effective in therapy of port-wine stains (PWSs). To evaluate the efficacy in treatment of PWSs with IPLS, a retrospective study was initiated. The data were collected by physicians working in private practices and departments of university hospitals and medical centers, respectively. A total of 37 randomly selected patients with a total of 40 PWSs were included in the study. Clinical PWS characteristics recorded were color and location of the PWS. All patients were treated with IPLS. Data collected included treatment parameter (filters, pulse duration, fluence, and pulse sequencing), percentage of clearance, and side effects (purpura, blisters, crusting, altered pigmentation, and scarring). Good and complete (70%-100%) clearance was achieved in 28 of 40 PWSs treated with IPLS. The average number of treatment sessions in PWSs reaching 100% clearance included 4.0 for pink PWSs and 1.5 for red PWSs. The average number of sessions for purple PWSs reaching good clearance (70%-99%) was 4.2 sessions. Parameters used most frequently were 515- and 550-nm cut-off filters, pulse duration of 2.5 to 5.0 milliseconds, and fluences of 24 to 60 J/cm2. Side effects included purpura in 133 (76%), superficial blisters in 14 (8%), and crusting in 35 (20%). Transient pigmentation changes were seen in 10.8% of patients (hypopigmentation in 3 [8.1%], hyperpigmentation in 1 [2.7%]). No scarring was observed. Intense pulsed light source presents an effective and safe method for treating PWSs, especially purple PWSs.
Cantharidin biosynthesis in a blister beetle: inhibition by 6-fluoromevalonate causes chemical disarmament.

PubMed

Carrel, J E; Doom, J P; McCormick, J P

1986-07-15

Biosynthesis of cantharidin in a blister beetle, Lytta polita, is effectively inhibited by 6-fluoromevalonate. Inhibition is attributed specifically to the fluorine substituent. Biochemical inhibition has not been demonstrated previously for an arthropod's defensive substance.
Exposure to a First World War blistering agent.

PubMed

Le, H Q; Knudsen, S J

2006-04-01

Sulfur mustards act as vesicants and alkylating agents. They have been used as chemical warfare since 1917 during the first world war. This brief report illustrates the progression of injury on a primary exposed patient to a first world war blistering agent. This case documents the rapid timeline and progression of symptoms. It emphasises the importance of appropriate personal protective equipment and immediate medical response plan with rapid decontamination and proper action from military and civilian medical treatment facilities. This case reports the first US active duty military exposure to a blistering agent in the age of global terrorism.
Advanced Diagnostic Techniques in Autoimmune Bullous Diseases

PubMed Central

Jindal, Anuradha; Rao, Raghavendra; Bhogal, Balbir S

2017-01-01

Autoimmune blistering diseases are diverse group of conditions characterized by blisters in the skin with or without mucosal lesions. There may be great degree of clinical and histopathological overlap; hence, advanced immunological tests may be necessary for more precise diagnosis of these conditions. Direct immunofluorescence microscopy is the gold standard tests to demonstrate the tissue-bound antibodies and should be done in all cases. Magnitude of antibody level in patient’ serum can be assessed by indirect immunofluorescence and enzyme linked immunosorbent assay. In this article we have reviewed the various techniques that are available in the diagnosis of autoimmune blistering diseases. PMID:28584369
Scanning electron microscopy of a blister roof in dystrophic epidermolysis bullosa*

PubMed Central

de Almeida Jr., Hiram Larangeira; Monteiro, Luciane; Silva, Ricardo Marques e; Rocha, Nara Moreira; Scheffer, Hans

2013-01-01

In dystrophic epidermolysis bullosa the genetic defect of anchoring fibrils leads to cleavage beneath the basement membrane, with its consequent loss. We performed scanning electron microscopy of an inverted blister roof of a case of dystrophic epidermolysis bullosa, confirmed by immunomapping and gene sequencing. With a magnification of 2000 times a net attached to the blister roof could be easily identified. This net was composed of intertwined flat fibers. With higher magnifications, different fiber sizes could be observed, some thin fibers measuring around 80 nm and thicker ones measuring between 200 and 300 nm. PMID:24474107
Prevention of Friction Blisters in Outdoor Pursuits: A Systematic Review.

PubMed

Worthing, Robert M; Percy, Raechel L; Joslin, Jeremy D

2017-06-01

The purpose of this systematic review was to determine if sock, antiperspirant, or barrier strategies were effective in prevention of friction blisters in wilderness and outdoor pursuits. A search of PubMed and EMBASE was conducted. Title, abstract, and full text articles were screened by 2 authors using predetermined inclusion and exclusion criteria to identify prospective controlled trials investigating prevention methods for friction blisters involving the foot. Only blisters associated with wilderness and outdoor pursuits (running, hiking, marching, etc.) were considered. Extraction of a predetermined data set was accomplished using a piloted form. Confidence in effect estimates were determined utilizing the Scottish Intercollegiate Guidelines Network methodology checklist. Literature search resulted in 806 discrete articles. After screening, 11 studies were identified for inclusion in systematic review. Included studies investigated 5 sock, 3 antiperspirant, and 3 barrier strategies. Only 2 articles were determined to have moderate confidence in effect estimate. Clinical and methodologic diversity precluded meta-analysis. Despite the high frequency, discomfort, and associated cost there is a paucity of high-quality quality evidence in support of socks, antiperspirants, or barriers for the prevention of friction blisters. Moderate confidence in effect estimate suggests that paper tape may be an effective form of barrier prevention. Published by Elsevier Inc.
Sugar Pine Seedlings not protected from blister rust by chemotherapeutants

Treesearch

George M. Harvey

1975-01-01

None of several types of chemotherapeutants applied before inoculation (antibiotics, metallic salts, systemic fungicides) prevented infection of sugar pine seedlings by white pine blister rust. DMSO (dimethyl sulfoxide) did not enhance the action of any material with which it was applied.
75 FR 17927 - Kevin Xu: Debarment Order

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-08

... products that bore the trademarks ZYPREXA, TAMIFLU, CASODEX, PLAVIX, and ARICEPT without the authorization... States various blister strips containing counterfeit TAMIFLU, CASODEX, ZYPREXA, and PLAVIX. On or about... of drugs that were misbranded, namely a shipment containing blister strips of PLAVIX pills that were...

Green tea catechins and their metabolites in human skin before and after exposure to ultraviolet radiation.

PubMed

Clarke, Kayleigh A; Dew, Tristan P; Watson, Rachel E B; Farrar, Mark D; Osman, Joanne E; Nicolaou, Anna; Rhodes, Lesley E; Williamson, Gary

2016-01-01

Dietary flavonoids may protect against sunburn inflammation in skin. Preliminary reports using less complete analysis suggest that certain catechins and their metabolites are found in skin biopsies and blister fluid after consumption of green tea; however, it is not known if they are affected by solar-simulated ultraviolet radiation (UVR) or whether conjugated forms, with consequently altered bioactivity, are present. The present study tested the hypothesis that UVR affects the catechin levels in the skin of healthy volunteers after consumption of green tea and how catechins in the plasma are related to their presence in skin tissue samples. In an open oral intervention study, 11 subjects consumed green tea and vitamin C supplements daily for 3months. Presupplementation and postsupplementation plasma samples, suction blister fluid and skin biopsies were collected; the latter two samples were collected both before and after UVR. A sensitive high-performance liquid chromatography/mass spectrometric assay was used to measure the intact catechin metabolites, conjugates and free forms. Seven green tea catechins and their corresponding metabolites were identified postsupplementation in skin biopsies, 20 in blister fluid and 26 in plasma, with 15 green tea catechin metabolites present in both blister fluid and plasma. The valerolactone, O-methyl-M4-O-sulfate, a gut microbiota metabolite of catechins, was significantly increased 1.6-fold by UVR in blister fluid samples. In conclusion, there were some common catechin metabolites in the plasma and blister fluid, and the concentration was always higher in plasma. The results suggest that green tea catechins and metabolites are bioavailable in skin and provide a novel link between catechin metabolites derived from the skin and gut microbiota. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.
Green tea catechins and their metabolites in human skin before and after exposure to ultraviolet radiation☆☆☆★

PubMed Central

Clarke, Kayleigh A.; Dew, Tristan P.; Watson, Rachel E.B.; Farrar, Mark D.; Osman, Joanne E.; Nicolaou, Anna; Rhodes, Lesley E.; Williamson, Gary

2016-01-01

Dietary flavonoids may protect against sunburn inflammation in skin. Preliminary reports using less complete analysis suggest that certain catechins and their metabolites are found in skin biopsies and blister fluid after consumption of green tea; however, it is not known if they are affected by solar-simulated ultraviolet radiation (UVR) or whether conjugated forms, with consequently altered bioactivity, are present. The present study tested the hypothesis that UVR affects the catechin levels in the skin of healthy volunteers after consumption of green tea and how catechins in the plasma are related to their presence in skin tissue samples. In an open oral intervention study, 11 subjects consumed green tea and vitamin C supplements daily for 3 months. Presupplementation and postsupplementation plasma samples, suction blister fluid and skin biopsies were collected; the latter two samples were collected both before and after UVR. A sensitive high-performance liquid chromatography/mass spectrometric assay was used to measure the intact catechin metabolites, conjugates and free forms. Seven green tea catechins and their corresponding metabolites were identified postsupplementation in skin biopsies, 20 in blister fluid and 26 in plasma, with 15 green tea catechin metabolites present in both blister fluid and plasma. The valerolactone, O-methyl-M4-O-sulfate, a gut microbiota metabolite of catechins, was significantly increased 1.6-fold by UVR in blister fluid samples. In conclusion, there were some common catechin metabolites in the plasma and blister fluid, and the concentration was always higher in plasma. The results suggest that green tea catechins and metabolites are bioavailable in skin and provide a novel link between catechin metabolites derived from the skin and gut microbiota. PMID:26454512
Commandra Blister Rust

Treesearch

David W. Johnson

1986-01-01

Commandra blister rust is a disease of hard pines that is caused by a fungus growing in the inner bark. The fungus (Cronartium commandrae Pk.) has a complex life cycle. It infects hard pines but needs an alternate host, an unrelated plant, to spread from one pine to another.
Graphene quantum blisters: A tunable system to confine charge carriers

NASA Astrophysics Data System (ADS)

Abdullah, H. M.; Van der Donck, M.; Bahlouli, H.; Peeters, F. M.; Van Duppen, B.

2018-05-01

Due to Klein tunneling, electrostatic confinement of electrons in graphene is not possible. This hinders the use of graphene for quantum dot applications. Only through quasi-bound states with finite lifetime has one achieved to confine charge carriers. Here, we propose that bilayer graphene with a local region of decoupled graphene layers is able to generate bound states under the application of an electrostatic gate. The discrete energy levels in such a quantum blister correspond to localized electron and hole states in the top and bottom layers. We find that this layer localization and the energy spectrum itself are tunable by a global electrostatic gate and that the latter also coincides with the electronic modes in a graphene disk. Curiously, states with energy close to the continuum exist primarily in the classically forbidden region outside the domain defining the blister. The results are robust against variations in size and shape of the blister which shows that it is a versatile system to achieve tunable electrostatic confinement in graphene.
Molecular Diagnosis in Autoimmune Skin Blistering Conditions

PubMed Central

Otten, J.V.; Hashimoto, T.; Hertl, M.; Payne, A.S.; Sitaru, C.

2014-01-01

Blister formation in skin and mucous membranes results from a loss of cell-cell or cell-matrix adhesion and is a common outcome of pathological events in a variety of conditions, including autoimmune and genetic diseases, viral and bacterial infections, or injury by physical and chemical factors. Autoantibodies against structural components maintaining cell-cell and cell-matrix adhesion induce tissue damage in autoimmune blistering diseases. Detection of these autoantibodies either tissue-bound or circulating in serum is essential to diagnose the autoimmune nature of disease. Various immunofluorescence methods as well as molecular immunoassays, including enzyme-linked immunosorbent assay and immunoblotting, belong to the modern diagnostic algorithms for these disorders. There is still a considerable need to increase awareness of the rare autoimmune blistering diseases, which often show a severe, chronic-relapsing course, among physicians and the public. This review article describes the immunopathological features of autoimmune bullous diseases and the molecular immunoassays currently available for their diagnosis and monitoring. PMID:24160488
Whitebark pine mortality related to white pine blister rust, mountain pine beetle outbreak, and water availability

USGS Publications Warehouse

Shanahan, Erin; Irvine, Kathryn M.; Thoma, David P.; Wilmoth, Siri K.; Ray, Andrew; Legg, Kristin; Shovic, Henry

2016-01-01

Whitebark pine (Pinus albicaulis) forests in the western United States have been adversely affected by an exotic pathogen (Cronartium ribicola, causal agent of white pine blister rust), insect outbreaks (Dendroctonus ponderosae, mountain pine beetle), and drought. We monitored individual trees from 2004 to 2013 and characterized stand-level biophysical conditions through a mountain pine beetle epidemic in the Greater Yellowstone Ecosystem. Specifically, we investigated associations between tree-level variables (duration and location of white pine blister rust infection, presence of mountain pine beetle, tree size, and potential interactions) with observations of individual whitebark pine tree mortality. Climate summaries indicated that cumulative growing degree days in years 2006–2008 likely contributed to a regionwide outbreak of mountain pine beetle prior to the observed peak in whitebark mortality in 2009. We show that larger whitebark pine trees were preferentially attacked and killed by mountain pine beetle and resulted in a regionwide shift to smaller size class trees. In addition, we found evidence that smaller size class trees with white pine blister rust infection experienced higher mortality than larger trees. This latter finding suggests that in the coming decades white pine blister rust may become the most probable cause of whitebark pine mortality. Our findings offered no evidence of an interactive effect of mountain pine beetle and white pine blister rust infection on whitebark pine mortality in the Greater Yellowstone Ecosystem. Interestingly, the probability of mortality was lower for larger trees attacked by mountain pine beetle in stands with higher evapotranspiration. Because evapotranspiration varies with climate and topoedaphic conditions across the region, we discuss the potential to use this improved understanding of biophysical influences on mortality to identify microrefugia that might contribute to successful whitebark pine conservation efforts. Using tree-level observations, the National Park Service-led Greater Yellowstone Interagency Whitebark Pine Long-term Monitoring Program provided important ecological insight on the size-dependent effects of white pine blister rust, mountain pine beetle, and water availability on whitebark pine mortality. This ongoing monitoring campaign will continue to offer observations that advance conservation in the Greater Yellowstone Ecosystem.
Cantharidin poisoning due to "Blister beetle" ingestion.

PubMed

Tagwireyi, D; Ball, D E; Loga, P J; Moyo, S

2000-12-01

Cantharidin, the active ingredient of "Spanish Fly", is contained in a number of insects collectively called blister beetles and is a well known toxin and vesicant. We report on a case of ingestion of Mylabris dicincta ("Blister beetle") in Zimbabwe by a 4 year old girl. The ingested beetles were probably mistaken for the edible Eulepida mashona. She presented with many of the classic signs and symptoms of cantharidin poisoning including haematuria and abdominal pains. This was recognised only after consultation with the drug information centre. She was managed conservatively, recovered and was discharged after 9 days. A overview of the clinical effects of cantharidin toxicity and its treatment is presented.
Antibiotic Treatment of Blister Rust Cankers in Eastern White Pine

Treesearch

William R. Phelps; Ray Weber

1970-01-01

Cycloheximide (Acti-dione) and Phytoactin antibiotics, applied as basal stem treatments, aerial spray treatments, and complete foliar drenches were not effective in controlling blister rust cankers in eastern white pine. Cycloheximide was effective in suppressing canker activity and growth if directly applied to scarified cankers.
Antibiotics Do Not Control Blister Rust in Eastern White Pine Seedlings

Treesearch

William R. Phelps; Ray Weber

1968-01-01

To prevent blister rust infections in Eastern white pine seedlings, the antibiotics, cycloheximide (acti-dione) and Phytoactin, were tested in root dips, root slurries, and foliar drenches before planting and after planting the trees. None of the methods and materials tested was effective.
Using Landscape Genetics Simulations for Planting Blister Rust Resistant Whitebark Pine in the US Northern Rocky Mountains.

PubMed

Landguth, Erin L; Holden, Zachary A; Mahalovich, Mary F; Cushman, Samuel A

2017-01-01

Recent population declines to the high elevation western North America foundation species whitebark pine, have been driven by the synergistic effects of the invasive blister rust pathogen, mountain pine beetle (MPB), fire exclusion, and climate change. This has led to consideration for listing whitebark pine (WBP) as a threatened or endangered species under the Endangered Species Act, which has intensified interest in developing management strategies for maintaining and restoring the species. An important, but poorly studied, aspect of WBP restoration is the spatial variation in adaptive genetic variation and the potential of blister rust resistant strains to maintain viable populations in the future. Here, we present a simulation modeling framework to improve understanding of the long-term genetic consequences of the blister rust pathogen, the evolution of rust resistance, and scenarios of planting rust resistant genotypes of whitebark pine. We combine climate niche modeling and eco-evolutionary landscape genetics modeling to evaluate the effects of different scenarios of planting rust-resistant genotypes and impacts of wind field direction on patterns of gene flow. Planting scenarios showed different levels for local extirpation of WBP and increased population-wide blister rust resistance, suggesting that the spatial arrangement and choice of planting locations can greatly affect survival rates of whitebark pine. This study presents a preliminary, but potentially important, framework for facilitating the conservation of whitebark pine.
SURFACE DECONTAMINATION EFFICACY STUDIES FOR ...

EPA Pesticide Factsheets

Technical Brief This Technical Brief summarizes the findings from three studies in which the decontamination efficacy was determined for various liquid contaminants when applied to various surfaces that are contaminated with blister agents (vesicants).This may provide decision-makers with practical information on surface decontaminations options during a blister agent response.
The influence of white pine blister rust on seed dispersal in whitebark pine

Treesearch

Shawn T. McKinney; Diana F. Tomback

2007-01-01

We tested the hypotheses that white pine blister rust (Cronartium ribicola J.C. Fisch.) damage in whitebark pine (Pinus albicaulis Engelm.) stands leads to reduced (1) seed cone density, (2) predispersal seed survival, and (3) likelihood of Clark's Nutcracker (Nucifraga columbiana (Wilson, 1811)) seed...
Distribution of Ribes, an alternate host of white pine blister rust, in Colorado and Wyoming

Treesearch

Holly S. J. Kearns; William R. Jacobi; Kelly S. Burns; Brian W. Geils

2008-01-01

Ribes (currants and gooseberries) are alternate hosts for Cronartium ribicola, the invasive fungus that causes blister rust of white pines (Pinus, subgenus Strobus) in the Rocky Mountain region of Colorado and Wyoming. The location, species, and density of Ribes can affect...
A randomised controlled trial to compare the safety, effectiveness and cost-effectiveness of doxycycline (200 mg/day) with that of oral prednisolone (0.5 mg/kg/day) for initial treatment of bullous pemphigoid: the Bullous Pemphigoid Steroids and Tetracyclines (BLISTER) trial.

PubMed

Chalmers, Joanne R; Wojnarowska, Fenella; Kirtschig, Gudula; Mason, James; Childs, Margaret; Whitham, Diane; Harman, Karen; Chapman, Anna; Walton, Shernaz; Schmidt, Enno; Godec, Thomas R; Nunn, Andrew J; Williams, Hywel C

2017-03-01

Bullous pemphigoid (BP) is an autoimmune blistering skin disorder with increased morbidity and mortality in the elderly. To evaluate the effectiveness, safety and cost-effectiveness of a strategy of initiating BP treatment with oral doxycycline or oral prednisolone. We hypothesised that starting treatment with doxycycline gives acceptable short-term blister control while conferring long-term safety advantages over starting treatment with oral prednisolone. Pragmatic multicentre two-armed parallel-group randomised controlled trial with an economic evaluation. A total of 54 dermatology secondary care centres in the UK and seven in Germany. Adults with BP [three or more blisters at two sites and positive direct and/or indirect immunofluorescence (immunoglobulin G and/or complement component 3 immunofluorescence at the dermal-epidermal junction)] and able to give informed consent. Participants were allocated using online randomisation to initial doxycycline treatment (200 mg/day) or prednisolone (0.5 mg/kg/day). Up to 30 g/week of potent topical corticosteroids was permitted for weeks 1-3. After 6 weeks, clinicians could switch treatments or alter the prednisolone dose as per normal practice. Primary outcomes: (1) the proportion of participants with three or fewer blisters at 6 weeks (investigator blinded) and (2) the proportion with severe, life-threatening and fatal treatment-related events at 52 weeks. A regression model was used in the analysis adjusting for baseline disease severity, age and Karnofsky score, with missing data imputed. Secondary outcomes included the effectiveness of blister control after 6 weeks, relapses, related adverse events and quality of life. The economic evaluation involved bivariate regression of costs and quality-adjusted life-years (QALYs) from a NHS perspective. In total, 132 patients were randomised to doxycycline and 121 to prednisolone. The mean patient age was 77.7 years and baseline severity was as follows: mild 31.6% (three to nine blisters), moderate 39.1% (10-30 blisters) and severe 29.3% (> 30 blisters). For those starting on doxycycline, 83 out of 112 (74.1%) had three or fewer blisters at 6 weeks, whereas for those starting on prednisolone 92 out of 101 (91.1%) had three or fewer blisters at 6 weeks, an adjusted difference of 18.6% in favour of prednisolone [90% confidence interval (CI) 11.1% to 26.1%], using a modified intention-to-treat (mITT) analysis. Per-protocol analysis showed similar results: 74.4% compared with 92.3%, an adjusted difference of 18.7% (90% CI 9.8% to 27.6%). The rate of related severe, life-threatening and fatal events at 52 weeks was 18.2% for those started on doxycycline and 36.6% for those started on prednisolone (mITT analysis), an adjusted difference of 19.0% (95% CI 7.9% to 30.1%; p = 0.001) in favour of doxycycline. Secondary outcomes showed consistent findings. There was no significant difference in costs or QALYs per patient at 1 year between doxycycline-initiated therapy and prednisolone-initiated therapy (incremental cost of doxycycline-initiated therapy £959, 95% CI -£24 to £1941; incremental QALYs of doxycycline-initiated therapy -0.024, 95% CI -0.088 to 0.041). Using a willingness-to-pay criterion of < £20,000 per QALY gained, the net monetary benefit associated with doxycycline-initiated therapy was negative but imprecise (-£1432, 95% CI -£3094 to £230). A strategy of starting BP patients on doxycycline is non-inferior to standard treatment with oral prednisolone for short-term blister control and considerably safer in the long term. The limitations of the trial were the wide non-inferiority margin, the moderate dropout rate and that serious adverse event collection was unblinded. Future work might include inducing remission with topical or oral corticosteroids and then randomising to doxycycline or prednisolone for maintenance. Current Controlled Trials ISRCTN13704604. This project was funded by the National Institute for Health Research (NIHR) Health Technology Assessment programme and will be published in full in Health Technology Assessment ; Vol. 21, No. 10. See the NIHR Journals Library website for further project information.
He behavior in Ni and Ni-based equiatomic solid solution alloy

NASA Astrophysics Data System (ADS)

Yan, Zhanfeng; Liu, Shaoshuai; Xia, Songqin; Zhang, Yong; Wang, Yugang; Yang, Tengfei

2018-07-01

In the current work, pure nickel (99.99 wt.%) and Ni-containing single phase equiatomic solid solution alloy Fe-Co-Cr-Ni were irradiated with 190 keV He ions at room temperature with different fluences and He behavior in both materials are compared. At 1 × 1017 cm-2, TEM observation reveals that only isolated and small He bubbles (1-2 nm) are formed in Fe-Co-Cr-Ni alloy while many small suspected "string"-like He bubbles are observed in nickel at the concentration peak region (5.5 at.%). When the fluence is increased to 5 × 1017 cm-2, average bubble size in nickel increases to ∼8 nm which is almost equal to that in Fe-Co-Cr-Ni, but a higher bubble density is observed in nickel. At the highest dose of 1 × 1018 cm-2, numerous surface blisters and exfoliations occur in nickel which are consistent with TEM observation, while the Fe-Co-Cr-Ni alloy only shows a slight surface blister. Bubble coarsening upon annealing at 500 °C (2 h) is observed at 5 × 1017 cm-2 in both alloys, but a significant larger bubble growth is observed in nickel, suggesting a relatively better resistance to He bubble growth for Fe-Co-Cr-Ni alloy.
Controlling diameter distribution of catalyst nanoparticles in arc discharge.

PubMed

Li, Jian; Volotskova, Olga; Shashurin, Alexey; Keidar, Michael

2011-11-01

It is demonstrated that the diameter distribution of catalyst nanoparticles in arc discharge can be controlled by a magnetic field. The magnetic field affects the arc shape, shortens the diffusing time of the catalyst nanoparticles through the nucleation zone, and consequentially reduces the average diameters of nanoparticles. The average diameter is reduced from about 7.5 nm without magnetic field to about 5 nm is the case of a magnetic field. Decrease of the catalyst nanoparticle diameter with magnetic field correlates well with decrease in the single-wall carbon nanotube and their bundles diameters.
Nitrous oxide for procedural analgesia at home in a child with epidermolysis bullosa.

PubMed

Ingelmo, Pablo; Wei, Andrew; Rivera, Gonzalo

2017-07-01

Epidermolysis bullosa comprises a range of conditions characterized by fragile skin with painful blistering induced by minor trauma and friction. The Dowling-Meara variant is a severe form characterized by disseminated painful blistering requiring lifelong skin and wound care. The natural history of the disease is characterized by a chronic course that tends to improve with advancing age. Various multimodal analgesic strategies have been proposed for painful procedures in children with epidermolysis bullosa. In this case report, we describe the use of nitrous oxide for pain control at home of blister treatments in a 4-year-old child with the Dowling-Meara variant. © 2017 John Wiley & Sons Ltd.
Growth of lodgepole pine stands and its relation to mountain pine beetle susceptibility

Treesearch

S.A. Mata; J.M. Schmid; W.K. Olsen

2003-01-01

Periodic diameter and basal area growth were determined for partially cut stands of lodgepole pine at five locations over approximately 10 year periods. After cutting, average diameters in the partially cut plots generally increased by 0.8 inches or more, while average diameter in the uncut controls increased by 0.6 inches or less. Diameter growth in the partially cut...
Utilization of Pipeline embolization device for treatment of ruptured intracranial aneurysms: US multicenter experience.

PubMed

Lin, Ning; Brouillard, Adam M; Keigher, Kiffon M; Lopes, Demetrius K; Binning, Mandy J; Liebman, Kenneth M; Veznedaroglu, Erol; Magarik, Jordan A; Mocco, J; Duckworth, Edward A; Arthur, Adam S; Ringer, Andrew J; Snyder, Kenneth V; Levy, Elad I; Siddiqui, Adnan H

2015-11-01

Utilization of the Pipeline embolization device (PED) in complex ruptured aneurysms has not been well studied. We evaluated the safety and effectiveness data from five participating US centers. Records of patients with ruptured cerebral aneurysms who underwent PED treatment between 2011 and 2013 were retrospectively reviewed. 26 patients with ruptured aneurysms underwent PED treatment (mean age 51.4 ± 13.2 years;16 women). At presentation, 8 patients (30.8%) had a Hunt-Hess grade of IV or above; 11 required extraventricular drain placement. Aneurysm morphologies were: 8 dissecting, 8 blister-like, 6 fusiform, and 4 saccular. There were 22 anterior circulation and 4 posterior circulation aneurysms. PED deployment was successful in all patients, with adjunctive coiling utilized in 12. Periprocedural complications occurred in 5 (19.2%), including 3 inhospital deaths. 23 patients (88.5%) had postoperative angiography at a mean of 5.9 months: 18 aneurysms (78.3%) were completely occluded, 3 (13.0%) had residual neck filling, and 2 (8.7%) had residual dome filling. All blister-type aneurysms were completely occluded at follow-up. Clinical follow-up was available for an average of 10.1 months (range 2-21 months), with one asymptomatic in-stent stenosis and one asymptomatic thromboembolic stroke noted. Good outcome (modified Rankin Scale (mRS) score of 0-2) was achieved in 20 patients (76.9%), fair (mRS 3-4) in 3 (11.5%), and 3 died (11.5%). The PED can be utilized for ruptured aneurysms and is a good option for blister-type aneurysms. However, due to periprocedural complications, it should be reserved for lesions that are difficult to treat by conventional clipping or coiling. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.
Developing blister rust resistance in white pines

Treesearch

Bohun B. Kinloch Jr.

2000-01-01

After a century since introduction to North America from Europe, white pine blister rust, caused by Cronartium ribicola J.C. Fisch., is recognized as one of the catastrophic plant disease epidemics in history. It has not yet stabilized and continues to spread and intensify. Its nine native white pine hosts comprise major timber producers, important...

Options for the management of white pine blister rust in the Rocky Mountain Region

Treesearch

Kelly S. Burns; Anna W. Schoettle; William R. Jacobi; Mary F. Mahalovich

2008-01-01

This publication synthesizes current information on the biology, distribution, and management of white pine blister rust (WPBR) in the Rocky Mountain Region. In this Region, WPBR occurs within the range of Rocky Mountain bristlecone pine (Pinus aristata), limber pine (P. flexilis), and whitebark pine (P. albicaulis...
Histology of white pine blister rust in needles of resistant and susceptible eastern white pine

Treesearch

Joel A. Jurgens; Robert A. Blanchette; Paul J. Zambino; Andrew David

2003-01-01

White pine blister rust, Cronartium ribicola, has plagued the forests of North America for almost a century. Over past decades, eastern white pine (Pinus strobus) that appear to tolerate the disease have been selected and incorporated into breeding programs. Seeds from P. strobus with putative resistance were...
Blister Packaging Medication to Increase Treatment Adherence and Clinical Response: Impact on Suicide-related Morbidity and Mortality

DTIC Science & Technology

2014-12-01

AD _ Award Number: W81XWH-09-1-0723 TITLE: Blister Packaging Medication to Increase Treatment Adherence and Clinical Response: Impact on Suicide ...Medication to Increase Treatment Adherence and Clinical Response: Impact on Suicide -related Morbidity and Mortality 5a. CONTRACT NUMBER 5b
White pine blister rust resistance research in Minnesota and Wisconsin

Treesearch

Andrew David; Paul Berrang; Carrie Pike

2012-01-01

The exotic fungus Cronartium ribicola causes the disease white pine blister rust on five-needled pines throughout North America. Although the effects of this disease are perhaps better known on pines in the western portion of the continent, the disease has also impacted regeneration and growth of eastern white pine (Pinus strobus L. ...
Experimental fungicidal control of blister rust on sugar pine in California

Treesearch

Clarence R. Quick

1964-01-01

Parallel series of exploratory experiments with antifungal antibiotics and conventional chemical fungicides for control of blister rust on sugar pine were started in northern California in 1959. Several fungicides, both antibiotic and conventional, appear slightly systemic, but all tested materials are more effective when sprayed directly on infected tissues....
A summary of white pine blister rust research in the Lake States.

Treesearch

Ralph L. Anderson

1973-01-01

Summarizes white pine blister rust research in the Lake States and present status of knowledge. Important microclimatic relations are described. Antibiotics are not effective, whereas pruning provides some control. Genetic resistance shows much promise but may be complicated by pathogenic races. The effectiveness of ribes eradication is open to question.
Genetic interactions in the white pine/blister rust pathosystem

Treesearch

Bohun B. Kinloch Jr.

2000-01-01

The nine white pine species native to North America have very different ecological roles and values, which include high quality timber production, important watershed protection, keystone ecological species, and the oldest and some of the most picturesque trees on earth. All are highly susceptible to white pine blister rust (Cronartium ribicola), and...
Resistance of three interspecific white pine hybrids to blister rust

Treesearch

R. Z. Callaham

1962-01-01

Three white pine hybrids exposed to infection by white pine blister rust (Cronartium ribicola Fischer) since 1946 have inherited the relative resistance of their parental species. The hybrids were produced from controlled pollinations in 1940 and 1941 at the Institute of Forest Genetics, Placerville, Calif. Twelve seedlings of each hybrid were...
Computer simulation of white pine blister rust epidemics

Treesearch

Geral I. McDonald; Raymond J. Hoff; William R. Wykoff

1981-01-01

A simulation of white pine blister rust is described in both word and mathematical models. The objective of this first generation simulation was to organize and analyze the available epidemiological knowledge to produce a foundation for integrated management of this destructive rust of 5-needle pines. Verification procedures and additional research needs are also...
BLISTERING AND DEGRADATION OF POLYURETHANE COATINGS UNDER DIFFERENT ACCELERATED WEATHERING TESTS. (R828081E01)

EPA Science Inventory

An epoxy primer with a high gloss polyurethane topcoat coating system was exposed either only in a QUV chamber or exposed in a QUV chamber and a Prohesion chamber, alternatively, in this study. AFM studies found that micro blisters formed on the coating surface after both expo...
A rare case of skin blistering and esophageal stenosis in the course of epidermolysis bullosa - case report and literature review.

PubMed

Michalak, Agata; Cichoż-Lach, Halina; Prozorow-Król, Beata; Buk, Leszek; Dzida, Monika

2018-04-13

Epidermolysis bullosa (EB) constitutes a heterogenous group of rare multisystem genetically transmitted disorders comprising several blistering muco-cutaneous diseases with a monogenic basis and either autosomal dominant or autosomal recessive mode of inheritance. EB manifestation is not only limited to the skin. Systemic signs might involve the nose, ear, eye, genitourinary tract and upper gastrointestinal tract. The presence of particular symptoms is directly determined by a type of altered skin protein. Gastrointestinal manifestation of EB is most commonly reflected by esophageal stenosis due to recurrent esophageal blistering, followed by consequent scarring. Here we present a case of a man with dystrophic EB and dysphagia, skin blistering, joints contractures and missing nails. To our knowledge, the presented man is the oldest one diagnosed with EB living in Poland. Management of an esophageal stricture in such circumstances is based on endoscopic dilatation. However, in most severe cases, placement of a gastrostomy tube is required. Despite great advances in medicine, a targeted therapy in the course of EB has not been established yet.
Chitosan-induced immunity in Camellia sinensis (L.) O. Kuntze against blister blight disease is mediated by nitric-oxide.

PubMed

Chandra, Swarnendu; Chakraborty, Nilanjan; Panda, Koustubh; Acharya, Krishnendu

2017-06-01

Blister blight disease, caused by an obligate biotrophic fungal pathogen, Exobasidium vexans Massee is posing a serious threat for tea cultivation in Asia. As the use of chemical pesticides on tea leaves substantially increases the toxic risks of tea consumption, serious attempts are being made to control such pathogens by boosting the intrinsic natural defense responses against invading pathogens in tea plants. In this study, the nature and durability of resistance offered by chitosan and the possible mechanism of chitosan-induced defense induction in Camellia sinensis (L.) O. Kuntze plants against blister blight disease were investigated. Foliar application of 0.01% chitosan solution at 15 days interval not only reduced the blister blight incidence for two seasons, but also maintained the induced expressions of different defense related enzymes and total phenol content compared to the control. Defense responses induced by chitosan were found to be down regulated under nitric oxide (NO) deficient conditions in vivo, indicating that the observed chitosan-induced resistance is probably activated via NO signaling. Such role of NO in host defense response was further established by application of the NO donor, sodium nitroprusside (SNP), which produced similar defense responses accomplished through chitosan treatment. Taken together, our results suggest that increased production of NO in chitosan-treated tea plants may play a critical role in triggering the innate defense responses effective against plant pathogens, including that causing the blister blight disease. Copyright © 2017 Elsevier Masson SAS. All rights reserved.
Blister Threshold Based Thermal Limits for the U-Mo Monolithic Fuel System

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. M. Wachs; I. Glagolenko; F. J. Rice

2012-10-01

Fuel failure is most commonly induced in research and test reactor fuel elements by exposure to an under-cooled or over-power condition that results in the fuel temperature exceeding a critical threshold above which blisters form on the plate. These conditions can be triggered by normal operational transients (i.e. temperature overshoots that may occur during reactor startup or power shifts) or mild upset events (e.g., pump coastdown, small blockages, mis-loading of fuel elements into higher-than-planned power positions, etc.). The rise in temperature has a number of general impacts on the state of a fuel plate that include, for example, stress relaxationmore » in the cladding (due to differential thermal expansion), softening of the cladding, increased mobility of fission gases, and increased fission-gas pressure in pores, all of which can encourage the formation of blisters on the fuel-plate surface. These blisters consist of raised regions on the surface of fuel plates that occur when the cladding plastically deforms in response to fission-gas pressure in large pores in the fuel meat and/or mechanical buckling of the cladding over damaged regions in the fuel meat. The blister temperature threshold decreases with irradiation because the mechanical properties of the fuel plate degrade while under irradiation (due to irradiation damage and fission-product accumulation) and because the fission-gas inventory progressively increases (and, thus, so does the gas pressure in pores).« less
Pharmacological properties of blister beetles (Coleoptera: Meloidae) promoted their integration into the cultural heritage of native rural Spain as inferred by vernacular names diversity, traditions, and mitochondrial DNA.

PubMed

Percino-Daniel, Nohemí; Buckley, David; García-París, Mario

2013-06-03

Beetles of the family Meloidae (blister beetles) are often reported in pharmacological literature because of their content of cantharidin. Cantharidin has a long history in human medicine and was commonly applied in the 19th and the early 20th centuries, although its use has been progressively abandoned since then. Contrary to most, even common, large species of Coleoptera, blister beetles of the genera Berberomeloe, Physomeloe and to a lesser extent Meloe, are usually recognized and often incorporated into local folk taxonomy by inhabitants of rural areas in Spain. To demonstrate the role that pharmacological properties of blister beetles must have played in their integration in the culture of early Iberian human societies, but also in the preservation of their identity until today, a rare case for Spanish insects. To achieve this purpose we document the diversity of vernacular names applied in rural areas of Spain, and we determine, using molecular data, the antiquity of the presence of two species of the better-known blister beetle in rural Spain, Berberomeloe majalis and Berberomeloe insignis. We try to document the extent of traditional knowledge of meloid beetles in rural areas by interviewing about 120 people from villages in central and southern Spain. We also use mitochondrial DNA sequences (Cytochrome Oxidase I and 16SrRNA) obtained from several populations of two species of the better known blister beetle in rural Spain, Berberomeloe majalis and Berberomeloe insignis, to determine whether these beetles were already present in the Iberian Peninsula when earlier ancient cultures were developing. Our results show that, based on mitochondrial DNA, blister beetles of the genus Berberomeloe were present in the Iberian Peninsula long before humans arrived, so ancient Iberian cultures were in contact with the same beetle species occurring now in rural areas. On the other hand, people interviewed in rural communities provided us with more than 28 different vernacular names, a few short songs incorporated to local folklore, and some therapeutic uses. Current knowledge of blister beetles of the family Meloidae in rural Spain was likely developed as a consequence of their pharmacological properties; we hypothesize this knowledge was inherited from ancient pre-Christian Iberian native cultures as part of their traditional therapeutic traditions. It is possible then, that current vernacular names and traditional songs are the only remnants of an ancient knowledge of pharmacological uses of meloid beetles, verbally transmitted from the ancestral cultures to modern day rural Spain. Our work suggests that this legacy, part of the European Cultural Heritage, is disappearing fast, in parallel to the loss of traditional agricultural techniques. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.
46 CFR 59.15-10 - Bagged or blistered shell plates.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Bagged or blistered shell plates. 59.15-10 Section 59.15... shell plates. (a) When the shell plates of cylindrical boilers which are exposed to the radiant heat of... boiler. (b) Where the shell plate is bagged due to overheating, the Officer in Charge, Marine Inspection...
46 CFR 59.15-10 - Bagged or blistered shell plates.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Bagged or blistered shell plates. 59.15-10 Section 59.15... shell plates. (a) When the shell plates of cylindrical boilers which are exposed to the radiant heat of... boiler. (b) Where the shell plate is bagged due to overheating, the Officer in Charge, Marine Inspection...
Effect of white pine blister rust (Cronartium ribicola) and rust-resistance breeding on genetic variation in western white pine Pinus monticola)

Treesearch

M. -S. Kim; S. J. Brunsfeld; G. I. McDonald; N. B. Klopfenstein

2003-01-01

Western white pine (Pinus monticola) is an economically and ecologically important species from western North America that has declined over the past several decades mainly due to the introduction of blister rust (Cronartium ribicola) and reduced opportunities for regeneration. Amplified fragment length polymorphism (AFLP) was used...
Characteristics of Blister Rust Cankers on Eastern White Pine

Treesearch

William R. Phelps; Ray Weber

1969-01-01

The growth, development, and sporulation of white pine blister rust cankers were studied on eastern white pine in Wisconsin and Minnesota. Three district canker types were identified on the basis of physical appearance, growth rate, and sporulation. Canker growth rate and sporulation decreased as tree size or age increased, and many cankers apparently became inactive...
Eliminating blister rust cankers from sugar pine by pruning.

Treesearch

G. L. Hayes; William I. Stein

1957-01-01

Well-stocked patches of vigorous advance reproduction are found in many deteriorating old-growth stands in southwestern Oregon. If carefully released from the over story, this reproduction can shorten the rotation length of the next crop by many years. Often sugar pine is the fastest-growing component of the reproduction, but it is frequently infected with blister rust...
White pines, Ribes, and blister rust: integration and action

Treesearch

R. S. Hunt; B. W. Geils; K. E. Hummer

2010-01-01

The preceding articles in this series review the history, biology and management of white pine blister rust in North America, Europe and eastern Asia. In this integration, we connect and discuss seven recurring themes important for understanding and managing epidemics of Cronartium ribicola in the white pines (five-needle pines in subgenus Strobus). Information and...

Polymerase Chain Reaction (PCR) applications in white pine blister rust resistance screening

Treesearch

Sam Hendricks; Wendy Sutton; Jeffrey Stone; Richard Sniezko; Angelia Kegley; Anna Schoettle

2011-01-01

A goal of breeding programs for resistance to white pine blister rust is the development of multigenic resistance, even if the genetics and mechanisms of resistance may be imperfectly understood. The goal of multigenic resistance has prompted efforts to categorize host resistance reactions at increasingly finer scales, to identify heritable traits that may confer...
A natural history of Cronartium ribicola

Treesearch

Brian W. Geils; Detlev R. Vogler

2011-01-01

Cronartium ribicola is a fungal pathogen that causes a blister rust disease of white pines, Ribes, and other hosts in the genera Castilleja and Pedicularis. Although blister rust can damage white pine trees and stands, the severity and significance of these impacts vary with time, place, and management. We use a natural history approach to describe the history, biology...
Proactive intervention to sustain high-elevation pine ecosystems threatened by white pine blister rust

Treesearch

Anna W. Schoettle; Richard A. Sniezko

2007-01-01

Only recently have efforts begun to address how management might prepare currently healthy forests to affect the outcome of invasion by established non-native pests. Cronartium ribicola, the fungus that causes the disease white pine blister rust (WPBR), is among the introductions into North America where containment and eradication have failed; the...
Pruning to manage white pine blister rust in the southern Rocky Mountains

Treesearch

Amanda Crump; William R. Jacobi; Kelly S. Burns; Brian E. Howell

2011-01-01

White pine blister rust is an exotic, invasive disease that severely damages and kills white pines in the southern Rocky Mountains. We evaluated the efficacy of preventive pruning (removing lower branches) and/or sanitation pruning (removing cankered branches) to reduce disease impacts in limber (Pinus flexilis James) and Rocky Mountain bristlecone (P. aristata Englm...
White pines, Ribes, and blister rust: a review and synthesis

Treesearch

Brian W. Geils; Kim E. Hummer; Richard S. Hunt

2010-01-01

For over a century, white pine blister rust (Cronartium ribicola) has linked white pines (Strobus) with currants and gooseberries (Ribes) in a complex and serious disease epidemic in Asia, Europe, and North America. Because of ongoing changes in climate, societal demands for forests and their amenities, and scientific advances in genetics and proteomics, our current...
White pine blister rust resistance in limber pine: Evidence for a major gene

Treesearch

A. W. Schoettle; R. A. Sniezko; A. Kegley; K. S. Burns

2014-01-01

Limber pine (Pinus flexilis) is being threatened by the lethal disease white pine blister rust caused by the non-native pathogen Cronartium ribicola. The types and frequencies of genetic resistance to the rust will likely determine the potential success of restoration or proactive measures. These first extensive inoculation trials using individual tree seed collections...
Resistance to white pine blister rust in Pinus flexilis and P

Treesearch

Anna W. Schoettle; Richard A. Sniezko; Angelia Kegley; Jerry Hill; Kelly S. Burns

2010-01-01

The non-native fungus Cronartium ribicola, that causes white pine blister rust (WPBR), is impacting or threatening limber pine, Pinus flexilis, and Rocky Mountain bristlecone pine, Pinus aristata. In the Southern Rockies, where the rust invasion is still expanding, we have the opportunity to be proactive and prepare the landscape for invasion. Genetic...
White pine blister rust in the interior Mountain West

Treesearch

Kelly Burns; Jim Blodgett; Dave Conklin; Brian Geils; Jim Hoffman; Marcus Jackson; William Jacobi; Holly Kearns; Anna Schoettle

2010-01-01

White pine blister rust is an exotic, invasive disease of white, stone, and foxtail pines (also referred to as white pines or five-needle pines) in the genus Pinus and subgenus Strobus (Price and others 1998). Cronartium ribicola, the fungus that causes WPBR, requires an alternate host - currants and gooseberries in the genus Ribes and species of Pedicularis...
Characterization of peanuts after dry roasting, oil roasting, and blister frying

USDA-ARS?s Scientific Manuscript database

Peanuts were systematically deep fried, blister fried, or dry roasted at 177°C to Hunter L-values of 53 ± 1, 48.5 ± 1, and 43 ± 1, corresponding to light, medium, and dark roasting, respectively. Thermal modifications of the epidermal and parenchyma cells were observed in the scanning electron micr...
TNFalpha and IL-6 are mediators in the blistering process of pemphigus.

PubMed

López-Robles, E; Avalos-Díaz, E; Vega-Memije, E; Hojyo-Tomoka, T; Villalobos, R; Fraire, S; Domíguez-Soto, L; Herrera-Esparza, R

2001-03-01

Pemphigus is an autoimmune disease characterized by intraepidermal blisters induced by pemphigus IgG. In addition to autoantibodies, molecular mechanisms involved in acantholysis remain largely unknown. For this reason, we address a possible role of the inflammatory cytokines IL-6 and TNFalpha in pemphigus lesions. Sixteen biopsies from patients with different types of pemphigus were studied by in situ hybridization using DNA fluorescent probes for IL-6 and TNFalpha mRNA. Fifty-six percent of lesional biopsies exhibited cytokine gene expression, which was poorly expressed in noninvolved skin. Deposits of TNFalpha and IL-6 were products of in situ transcription at the epidermal level. Inflammatory cytokine expression around the blister could play a mediator role in pemphigus lesions by increasing epithelial damage.
Experimental study of cryogen spray properties for application in dermatologic laser surgery.

PubMed

Aguilar, Guillermo; Majaron, Boris; Karapetian, Emil; Lavernia, Enrique J; Nelson, J Stuart

2003-07-01

Cryogenic sprays are used for cooling human skin during laser dermatologic surgery. In this paper, six straight-tube nozzles are characterized by photographs of cryogenic spray shapes, as well as measurements of average droplet diameter, velocity, and temperature. A single-droplet evaporation model to predict average spray droplet diameter and temperature is tested using the experimental data presented here. The results show two distinct spray patterns--sprays for 1.4-mm-diameter nozzles (wide nozzles) show significantly larger average droplet diameters and higher temperatures as a function of distance from the nozzle compared with those for 0.5-0.8-mm-diameter nozzles (narrow nozzles). These results complement and support previously reported studies, indicating that wide nozzles induce more efficient heat extraction than the narrow nozzles.
Status of whitebarkpine in the Greater Yellowstone Ecosystem: A step-trend analysis comparing 2004-2007 to 2008-2011

USGS Publications Warehouse

Shanahan, Erin; Irvine, Kathryn M.; Roberts, Dave; Litt, Andrea R.; Legg, Kristin; Daley, Rob; Chambers, Nina

2014-01-01

Whitebark pine (Pinus albicaulis) is a foundation and keystone species in upper subalpine environments of the northern Rocky Mountains that strongly influences the biodiversity and productivity of high-elevation ecosystems (Tomback et al. 2001, Ellison et al. 2005). Throughout its historic range, whitebark pine has decreased significantly as a major component of high-elevation forests. As a result, it is critical to understand the challenges to whitebark pine—not only at the tree and stand level, but also as these factors influence the distribution of whitebark pine across the Greater Yellowstone Ecosystem (GYE). In 2003, the National Park Service (NPS) Greater Yellowstone Inventory & Monitoring Network identified whitebark pine as one of twelve significant natural resource indicators or vital signs to monitor (Jean et al. 2005, Fancy et al. 2009) and initiated a long-term, collaborative monitoring program. Partners in this effort include the U.S. Geological Survey, U.S. Forest Service, and Montana State University with representatives from each comprising the Greater Yellowstone Whitebark Pine Monitoring Working Group. The objectives of the monitoring program are to assess trends in (1) the proportion of live, whitebark pine trees (>1.4-m tall) infected with white pine blister rust (blister rust); (2) to document blister rust infection severity by the occurrence and location of persisting and new infections; (3) to determine mortality of whitebark pine trees and describe potential factors contributing to the death of trees; and (4) to assess the multiple components of the recruitment of understory whitebark pine into the reproductive population. In this report we summarize the past eight years (2004-2011) of whitebark pine status and trend monitoring in the GYE. Our study area encompasses six national forests (NF), two national parks (NP), as well as state and private lands in portions of Wyoming, Montana, and Idaho; this area is collectively described as the GYE here and in other studies. The sampling design is a probabilistic, twostage cluster design with stands of whitebark pine as the primary units and 10x50 m belt transects as the secondary units. Primary sampling units (stands) were selected randomly from a sample frame of approximately 10,770 mapped pure and mixed whitebark pine stands ≥2.0 hectares in the GYE (Dixon 1997, Landenburger 2012). From 2004 through 2007 (monitoring transect establishment or initial time-step), we established 176 permanent belt transects (secondary sampling units=176) in 150 whitebark pine stands and permanently marked approximately 4,740 individual trees >1.4 m tall to monitor long-term changes in blister rust infection and survival rates. Between 2008 and 2011 (revisit time-step), these same 176 transects were surveyed and again all previously tagged trees were observed for changes in blister rust infection and survival status. Objective 1. Using a combined ratio estimator, we estimated the proportion of live trees infected in the GYE in the initial time-step (2004-2007) to be 0.22 (0.031 SE). Following the completion of all surveys in the revisit time-step (2008-2011), we estimated the proportion of live trees infected with white pine blister rust as 0.23 (0.028 SE; Table 2). We detected no significant change in the proportion of trees infected in the GYE between the two time-steps. Objective 2. We documented blister rust canker locations as occurring in the canopy or bole. We compared changes in canker position between the initial time-step (2004-2007) and the revisit time-step (2008-2011) in order to assess changes in infection severity. This analysis included the 3,795 trees tagged during the initial time-step that were located and documented as alive at the end of the revisit time-step. At the end of the revisit time-step, we found 1,217 trees infected with blister rust. This includes the 287 newly tagged trees in the revisit time step of which 14 had documented infections. Of these 1,217 trees, 780 trees were infected with blister rust in both time steps. Trees with only canopy cankers made up approximately 43% (519 trees) of the total number of trees infected with blister rust at the end of the revisit time-step, while trees with only bole cankers comprised 20% (252 trees), and those with both canopy and bole cankers included 37% (446 trees) of the infected sample. A bole infection is considered to be more consequential than a canopy canker, as it compromises not only the overall longevity of the tree, but its functional capacity for reproductive output as well (Kendall and Arno 1990, Campbell and Antos 2000, McDonald and Hoff 2001, Schwandt and Kegley 2004). In addition to infection location, we also documented infection transition between the canopy and bole. Of the 780 live trees that were infected with blister rust in both time-steps, approximately 31% (242) maintained canopy cankers and 36% (281) retained bole infections at the end of the revisit time-step. Infection transition from canopy to bole occurred in 30% (234) of the revisit time-step trees while 3% (23) transitioned from bole to canopy infections during this period. Objective 3. To determine whitebark pine mortality, we resurveyed all belt transects to reassess the life status of permanently tagged trees >1.4 m tall. We compared the total number of live tagged trees recorded during monitoring transect establishment to the total number of resurveyed dead tagged trees recorded during the revisit time-step and identified all potential mortality-influencing conditions (blister rust, mountain pine beetle, fire and other). By the end of the revisit time-step, we observed a total of 975 dead tagged whitebark pine trees; using a ratio estimator, this represents a loss of approximately 20% (SE=4.35%) of the original live tagged tree population (GYWPMWG 2012). Objective 4. To investigate the proportion of live, reproducing tagged trees, we divided the total number of positively identified cone-bearing trees by the total number of live trees in the tagged tree sample at the end of the revisit time-step. To approximate the average density of recruitment trees per stand, trees ≤1.4 m tall were summed by stand (within the 500 m² transect area) and divided by the total number of stands. Reproducing trees made up approximately 24% (996 trees) of the total live tagged population at the end of the revisit time-step. Differentiating between whitebark pine and limber pine seedlings or saplings is problematic given the absence of cones or cone scars. Therefore, understory summaries as presented in this report may include individuals of both species when they are sympatric in a stand. The average density of small trees ≤1.4 m tall was 53 understory trees per 500 m². Raw counts of these understory individuals ranged from 0-635 small trees per belt transect. In addition, a total of 287 trees were added to the tagged tree population by the end of 2011. These newly tagged trees were individuals that upon subsequent revisits had reached a height of >1.4 m tall and subsequently added to the sample. Throughout the past decade in the GYE, monitoring has helped document shifts in whitebark pine forests; whitebark pine stands have been impacted by insect, pathogen, wildland fire, and other disturbance events. Blister rust infection is ubiquitous throughout the ecosystem and infection proportions are variable across the region. And while we have documented mortality of whitebark pine, we have also recorded considerable recruitment. We provide this first step-trend report as a quantifiable baseline for understanding the state of whitebark pine in the GYE. Many aspects of whitebark pine health are highly variable across the range of its distribution in the GYE. Through sustained implementation of the monitoring program, we will continue efforts to document and quantify whitebark pine forest dynamics as they arise under periodic upsurges in insect, pathogen, fire episodes, and climatic events in the GYE. Since its inception, this monitoring program perseveres as one of the only sustained longterm efforts conducted in the GYE with a singular purpose to track the health and status of this prominent keystone species.
Survival and growth of black walnut families after 7 years in West Virginia

Treesearch

G. W. Wendel; Donald E. Dorn; Donald E. Dorn

1985-01-01

Average survival, 7-year stem diameter, and stem diameter growth differed significantly among 34 black walnut families planted in West Virginia. Average total height, height growth, and diameter at breast height were not significantly different among families. Families were from seed collected in West Virginia, Pennsylvania, North Carolina, and Tennessee. The 7-year...
Diameter Growth of Southern Bottomland Hardwoods

Treesearch

Henry Bull

1945-01-01

There is very little published information on average rates of diameter growth of southern bottomland hardwoods. Probably the best information of this kind is given by Winters, Putnam, and Eldredge,2 who summarize forest survey data on average rates of diameter growth for 4 size classes and 20 species or species groups (including pine and cyress), and for all species...
Height diameter relations of maple street trees

Treesearch

David J. Nowak

1990-01-01

Height and diameter measurements were taken for silver, sugar and Norway maple street trees in Rochester and Syracuse, New York. Mature silver maples proved to be the tallest of the three species. Average sugar maple height was consistently taller than Norway maple height until diameters reached 28 inches. Average mature tree height for all three species level off in...
Limber pine forests on the leading edge of white pine blister rust distribution in Northern Colorado

Treesearch

Jennifer G. Klutsch; Betsy A. Goodrich; Anna W. Schoettle

2011-01-01

The combined threats of the current mountain pine beetle (Dendroctonus ponderosae, MPB) epidemic with the imminent invasion of white pine blister rust (caused by the non-native fungus Cronartium ribicola, WPBR) in limber pine (Pinus flexilis) forests in northern Colorado threatens the limber pine's regeneration cycle and ecosystem function. Over one million...
Using landscape genetics simulations for planting blister rust resistant whitebark pine in the US northern Rocky Mountains

Treesearch

Erin L. Landguth; Zachary A. Holden; Mary F. Mahalovich; Samuel A. Cushman

2017-01-01

Recent population declines to the high elevation western North America foundation species whitebark pine, have been driven by the synergistic effects of the invasive blister rust pathogen, mountain pine beetle (MPB), fire exclusion, and climate change. This has led to consideration for listing whitebark pine (WBP) as a threatened or endangered species under the...
Chemical control of blister rust on sugar pine...two fungicides show promise in California tests

Treesearch

Clarence R. Quick

1967-01-01

Among several fungicides tested, Phytoactin L-340 and Dowicide 1 (o-phenylphenol) showed the most promise for systemic chemical control of blister rust on sugar pine in northern California. The trials included 22 tests on 224 sugar pines: five with Acti-dione BR (cycloheximide), one each with five common chemical fungicides,and 12 with phytoactin. Apparent...
Synoptic climatology of the long-distance dispersal of white pine blister rust II. Combination of surface and upper level conditions

Treesearch

K. L. Frank; B. W. Geils; L. S. Kalkstein; H. W. Thistle

2008-01-01

An invasive forest pathogen, Cronartium ribicola, white pine blister rust (WPBR), is believed to have arrived in the Sacramento Mountains of south-central New Mexico about 1970. Epidemiological and genetic evidence supports the hypothesis that introduction was the result of long-distance dispersal (LDD) by atmospheric transport from California. This...
Selection for resistance to white pine blister rust affects the abiotic stress tolerances of limber pine

Treesearch

Patrick J. Vogan; Anna W. Schoettle

2015-01-01

Limber pine (Pinus flexilis) mortality is increasing across the West as a result of the combined stresses of white pine blister rust (Cronartium ribicola; WPBR), mountain pine beetle (Dendroctonus ponderosae), and dwarf mistletoe (Arceuthobium cyanocarpum) in a changing climate. With the continued spread of WPBR, extensive mortality will continue with strong selection...

Strong partial resistance to white pine blister rust in sugar pine

Treesearch

Bohun B. Kinloch, Jr.; Deems Burton; Dean A. Davis; Robert D. Westfall; Joan Dunlap; Detlev Vogler

2012-01-01

Quantitative resistance to white pine blister rust in 128 controlled- and open-pollinated sugar pine families was evaluated in a âdisease gardenâ, where alternate host Ribes bushes were interplanted among test progenies. Overall infection was severe (88%), but with great variation among and within families: a 30-fold range in numbers of infections...
Kindler syndrome: report of two cases.

PubMed

Mendes, Luciana; Nogueira, Lisiane; Vilasboas, Virginia; Talhari, Carolina; Talhari, Sinésio; Santos, Mônica

2012-01-01

Kindler syndrome is a rare autosomal recessive genodermatosis characterized by trauma-induced blisters, progressive poikiloderma and varying degrees of photosensitivity. In 2003, loss-of-function mutations were identified in the gene KIND1 mapped to chromosome 20p12.3. In this paper, we report Kindler syndrome in two children born to consanguineous parents presenting acral blistering, photosensitivity, poikiloderma, cutaneous atrophy and periodontitis.
Distribution and frequency of a gene for resistance to white pine blister rust in natural populations of sugar pine

Treesearch

Bohun B. Kinloch Jr.

1992-01-01

The gametic frequency of a dominant allcle (R) for resistance to white pine blister rust, a disease caused by an introduced pathogen (Cronartium ribicola), in natural populations of sugar pine was estimated by the kind of leaf symptom expressed after artificial inoculation of wind-pollinated seedlings from susceptible seed-parent...
Random amplified polymorphic DNA markers tightly linked to a gene for resistance to white pine blister rust in sugar pine

Treesearch

Michael E. Devey; Annette Delfino-Mix1; Bohun B. Kinloch; David B. NEALEt

1995-01-01

We have genetically mapped a gene for resistance to white pine blister rust (Cronartium ribicola Fisch.) in sugar pine (Pinus lambertiana Dougl.) by using an approach which relies on three factors: (i) the ability to assay for genetic markers in the haploid stage of the host's life cycle, using...
Monitoring white pine blister rust infection and mortality in whitebark pine in the Greater Yellowstone ecosystem

Treesearch

Cathie Jean; Erin Shanahan; Rob Daley; Gregg DeNitto; Dan Reinhart; Chuck Schwartz

2011-01-01

There is a critical need for information on the status and trend of whitebark pine (Pinus albicaulis) in the Greater Yellowstone Ecosystem (GYE). Concerns over the combined effects of white pine blister rust (WPBR, Cronartium ribicola), mountain pine beetle (MPB, Dendroctonus ponderosae), and climate change prompted an interagency working group to design and implement...
Blister rust control in the management of western white pine

Treesearch

Kenneth P. Davis; Virgil D. Moss

1940-01-01

The forest industry of the western white pine region depends on the production of white pine as a major species on about 2,670,000 acres of commercial forest land. Continued production of this species and maintenance of the forest industry at anything approaching its present level is impossible unless the white pine blister rust is controlled. Existing merchantable...
Modeling the potential distribution of white pine blister rust in the central Rocky Mountains.

Treesearch

Holly S. J. Kearns; William R. Jacobi

2006-01-01

Cronartium ribicola (J. C. Fischer ex Rabh.), the causal agent of white pine blister rust (WPBR), was introduced to western North America via infected nursery stock imported from France to Point Grey near Vancouver, British Columbia (Mielke 1943). Primary infection of white pines occurs on the needles where fungal spores land, enter through stomata,...
White pine blister rust in high-elevation white pines: Screening for simply-inherited, hypersensitive resistance

Treesearch

Detlev R. Vogler; Annette Delfino-Mix; Anna W. Schoettle

2006-01-01

Recent concern about survival and recovery of high-elevation white pine ecosystems has returned white pine blister rust (caused by Cronartiurn ribicola) to prominence as a significant threat to forest health in the western U.S. (Sainman et al., 2003). This, in turn, has spurred new research into potential rust-resistance mechanisms in high-elevation...
The relationship between whitebark pine health, cone production, and nutcracker occurrence across four National Parks

Treesearch

Lauren E. Barringer; Diana F. Tomback; Michael B. Wunder

2011-01-01

Whitebark pine (Pinus albicaulis) is declining in the central and northern Rocky Mountains from infection by the exotic pathogen Cronartium ribicola, which causes white pine blister rust, and from outbreaks of mountain pine beetle (Dendroctonus ponderosae). White pine blister rust has been present in Glacier and Waterton Lakes National Parks (NP) about two decades...
Unusual presentation of childhood Systemic Lupus Erythematosus

PubMed Central

Kumar, Sathish; Agarwal, Indira

2007-01-01

Bullous systemic lupus erythematosus is a rare blistering condition with a distinctive combination of clinical, histological and immunopathologic features that together constitute a unique bullous disease phenotype. It is often associated with autoimmunity to type VII collagen. Here we report a child who presented with bullous systemic lupus erythematosus. Rapid resolution of the blisters occurred following treatment with dapsone. PMID:18028550
Influence of host resistance on the genetic structure of the white pine blister rust fungus in the western United States

Treesearch

B. A. Richardson; N. B. Klopfenstein; P. J. Zambino; G. I. McDonald; B. W. Geils; L. M. Carris

2008-01-01

Cronartium ribicola, the causal agent of white pine blister rust, has been devastating to five-needled white pines in North America since its introduction nearly a century ago. However, dynamic and complex interactions occur among C. ribicola, five-needled white pines, and the environment. To examine potential evolutionary...
Preempting the pathogen: Blister rust and proactive management of high-elevation pines

Treesearch

Sue Miller; Anna Schoettle; Kelly Burns; Richard Sniezko; Patty Champ

2017-01-01

White pine blister rust has been spreading through western forests since 1910, causing widespread mortality in a group that includes some of the oldest and highest-elevation pines in the United States. The disease has recently reached Colorado and is expected to travel through the southern Rockies. Although it cannot be contained, RMRS researchers and collaborators are...
HOW TO Identify White Pine Blister Rust and Remove Cankers

Treesearch

Thomas H. Nicholls; Robert L. Anderson

1977-01-01

White pine blister rust (caused by the fungus Cronartium ribicola J. C. Fisch. ex Rabenh.) was introduced into the United States about 1900 and has since spread throughout the range of white pine. The disease intensity varies throughout the range but is normally most severe where late summers (July-September) are cool (below 67? F) and damp, conditions necessary for...
Environment in relation to white pine blister rust infection

Treesearch

E.P. Van Arsdel

1972-01-01

Pine trees can be free of blister rust infection either because they are growing in a climate unfavorable to rust or because they are genetically resistant to the rust. The climatic escape is hundreds of times more common than genetic resistance in the American white pines. The minimum time and temperature required for penetration by an isolate of the rice blast fungus...
Aiding blister rust control by silvicultural measures in the western white pine type

Treesearch

Virgil D. Moss; Charles A. Wellner

1953-01-01

The forest industry of the Inland Empire depends on the production of western white pine (Pinus monticola Dougl.) as a major species. Continued production of this tree is impossible unless white pine blister rust (Cronartium ribicola Fischer) is controlled. Existing merchantable timber can and probably will be harvested before serious losses occur, but the young growth...
Assessing host specialization among aecial and telial hosts of the white pine blister rust fungus, Cronartium ribicola

Treesearch

Bryce A. Richardson; Paul J. Zambino; Ned B. Klopfenstein; Geral I. McDonald; Lori M. Carris

2007-01-01

The white-pine blister rust fungus, Cronartium ribicola Fisch. in Rabenh., continues to spread in North America, utilizing various aecial (primary) and telial (alternate) hosts, some of which have only recently been discovered. This introduced pathogen has been characterized as having low genetic diversity in North America, yet it has demonstrated a...
Direct current microhollow cathode discharges on silicon devices operating in argon and helium

NASA Astrophysics Data System (ADS)

Michaud, R.; Felix, V.; Stolz, A.; Aubry, O.; Lefaucheux, P.; Dzikowski, S.; Schulz-von der Gathen, V.; Overzet, L. J.; Dussart, R.

2018-02-01

Microhollow cathode discharges have been produced on silicon platforms using processes usually used for MEMS fabrication. Microreactors consist of 100 or 150 μm-diameter cavities made from Ni and SiO2 film layers deposited on a silicon substrate. They were studied in the direct current operating mode in two different geometries: planar and cavity configuration. Currents in the order of 1 mA could be injected in microdischarges operating in different gases such as argon and helium at a working pressure between 130 and 1000 mbar. When silicon was used as a cathode, the microdischarge operation was very unstable in both geometry configurations. Strong current spikes were produced and the microreactor lifetime was quite short. We evidenced the fast formation of blisters at the silicon surface which are responsible for the production of these high current pulses. EDX analysis showed that these blisters are filled with argon and indicate that an implantation mechanism is at the origin of this surface modification. Reversing the polarity of the microdischarge makes the discharge operate stably without current spikes, but the discharge appearance is quite different from the one obtained in direct polarity with the silicon cathode. By coating the silicon cathode with a 500 nm-thick nickel layer, the microdischarge becomes very stable with a much longer lifetime. No current spikes are observed and the cathode surface remains quite smooth compared to the one obtained without coating. Finally, arrays of 76 and 576 microdischarges were successfully ignited and studied in argon. At a working pressure of 130 mbar, all microdischarges are simultaneously ignited whereas they ignite one by one at higher pressure.
Cryosurgical treatment of professional chronic radiodermatitis.

PubMed

Conejo-Mir, J S; Moreno, J C; Camacho, F

1997-06-01

Chronic x-ray dermatitis in professionals is a frequent problem for doctors in our country due to the fact that many of them widely used radiotherapy without any protection 15-20 years ago. Surgery has been the most accepted treatment, though it generally decreases hand function. Up to now, cryosurgery was not usually considered as a possible treatment if the lesions were located on fingers. In this study, the advantages of cryosurgery for the treatment of professional chronic radiodermatitis with incipient pretumoral lesions are emphasized. Cryosurgery was performed on six patients affected with chronic professional radiodermatitis that showed keratomas and ulcerations, using both spray (keratomas) and a probe 0.5 cm in diameter (ulcerations, in situ squamous cell carcinoma). Nerve block anesthesia with mepivacaine 1% was used in all cases. Before the treatment, all suspected lesions were biopsied; if invasive squamous cell carcinoma was revealed in the dermatopathological study, the patient was rejected. Variables such as blister and necrosis formation, pain, and achromatic, sensibility, and mobility disorders were studied. The follow-up period was 2 years. Immediate postoperative results showed great pain and blistering in all cases. Residual achromias were observed early postoperatively in all cases, but were repigmented 1 year after therapy in four cases (66%). Sensory alterations (hypo- and hyperthesias) were found in four cases (66%) 1 month after treatment, although this complication was not observed 6 months after treatment. Finger mobility was perfect in all cases 2 months after treatment, and there was no recurrence in any case after 2 years of follow-up. We believe cryosurgery must be considered as an excellent treatment for professional chronic radiodermatitis with keratomas, ulcerations, and incipient squamous cell carcinomas. Its use may prevent further dramatic surgical treatment, like amputations, allowing the preservation of finger function.
Diagnostic pitfalls in newborns and babies with blisters and erosions.

PubMed

Nischler, Elke; Klausegger, Alfred; Hüttner, Clemens; Pohla-Gubo, Gabriele; Diem, Anja; Bauer, Johann W; Hintner, Helmut

2009-01-01

Establishing the correct diagnosis in newborns presenting with blisters and erosions is not always a straightforward process. Many different disease entities including acquired (i.e., infectious, immunobullous, traumatic) and inherited disorders have to be taken into consideration. Similarities in clinical appearance, colonization and/or superinfections of preexisting skin lesions, as well as the absence of late changes in the neonate often pose significant diagnostic challenges. In this paper we discuss by giving examples the process of making an accurate diagnosis of blistering skin diseases in the neonatal period on the basis of a diagnostic algorithm. In addition, we provide an overview of the rational use and the limitations of laboratory procedures such as microbial testing, routine light microscopy, immunofluorescence antigen mapping, transmission electron microscopy, and molecular genetic analysis.
Necrotizing Fasciitis: Diagnostic Challenges in a Mute Bedridden Patient with Atypical Laboratory Parameters

PubMed Central

Lohiya, Ghan-Shyam; Tan-Figueroa, Lilia; Krishna, Vijay; Lohiya, Sunita

2012-01-01

A 27-year-old mute bedridden patient required parenteral corticosteroids and antibiotics, and hospitalization for an acute respiratory illness. After 2 days, staff noted a ~0.3 cm blister on the patient's right heel. Within 19 hours, blistering increased and the foot became partly gangrenous. The patient developed high fever (40.3°C), and leukocytosis (count: 13 × 109/L; was 6.5 × 109/L ten days earlier). Necrotizing fasciitis (NF) was diagnosed and treated with emergency leg amputation. Histopathology revealed necrosis of fascia, muscle, subcutaneous tissue, and skin. In bedridden patients, corticosteroids may particularly facilitate serious infections, and initial NF blistering may be mistaken for pressure ulcers. Vigilant and frequent whole body monitoring is necessary for all patients incapable of verbalizing their symptoms. PMID:23197984

Necrotizing fasciitis: diagnostic challenges in a mute bedridden patient with atypical laboratory parameters.

PubMed

Lohiya, Ghan-Shyam; Tan-Figueroa, Lilia; Krishna, Vijay; Lohiya, Sunita

2012-01-01

A 27-year-old mute bedridden patient required parenteral corticosteroids and antibiotics, and hospitalization for an acute respiratory illness. After 2 days, staff noted a ~0.3 cm blister on the patient's right heel. Within 19 hours, blistering increased and the foot became partly gangrenous. The patient developed high fever (40.3°C), and leukocytosis (count: 13 × 10(9)/L; was 6.5 × 10(9)/L ten days earlier). Necrotizing fasciitis (NF) was diagnosed and treated with emergency leg amputation. Histopathology revealed necrosis of fascia, muscle, subcutaneous tissue, and skin. In bedridden patients, corticosteroids may particularly facilitate serious infections, and initial NF blistering may be mistaken for pressure ulcers. Vigilant and frequent whole body monitoring is necessary for all patients incapable of verbalizing their symptoms.
Are Senna based laxatives safe when used as long term treatment for constipation in children?

PubMed

Vilanova-Sanchez, Alejandra; Gasior, Alessandra C; Toocheck, Nicole; Weaver, Laura; Wood, Richard J; Reck, Carlos A; Wagner, Andrea; Hoover, Erin; Gagnon, Renae; Jaggers, Jordon; Maloof, Tassiana; Nash, Onnalisa; Williams, Charae; Levitt, Marc A

2018-04-01

Senna is a stimulant laxative commonly used by pediatricians, pediatric gastroenterologists, and pediatric surgeons. Many clinicians avoid Senna for reasons such as tolerance or side effects but this has little scientific justification. We recently found several patients we were caring for developed perineal blistering during the course of Senna treatment. Because of this we chose to review the literature to identify side effects in children taking this medication as well as to analyze our Center's experience with Senna's secondary effects. We performed a literature review (MEDLINE, PUBMED) using the keywords of Senna, sen, sennosides and children, and pediatric and functional (idiopathic) constipation. We looked for articles with information regarding perineal blisters related to Senna as well as other secondary effects of Senna laxatives in children when used on a long-term basis. We also reviewed the charts of our patients who had previously taken Senna or are currently taking Senna, looking for adverse reactions. Eight articles in the literature reported perineal blisters after administration of Senna laxatives in 28 patients. Of those occurrences, 18 patients (64%) had accidental administration of Senna and 10 (36%) had Senna prescribed as a long term treatment. All of the blistering episodes were related to high dose, night-time accidents, or intense diarrhea with a long period of stool to skin contact. At our institution, from 2014 to 2017, we prescribed Senna and have recorded data to 640 patients. During the study period, 17 patients (2.2%) developed blisters during their treatment. Patients who developed blisters had higher doses 60mg/day; 60 [12-100] vs. 17.5 [1.7-150] (p<0.001). All of the blistering episodes were related to night-time accidents, with a long period of stool to skin contact. 83 (13%) patients presented minor side effects such as abdominal cramping, vomiting or diarrhea which resolved once the type of laxatives were changed or enemas were started. The doses of Senna was not significantly different in these patients 15mg/day [4.4-150] vs. 17.5mg/day [1.5-150]. There were no other long-term side effects from Senna found in the pediatric literature for long-term treatment besides abdominal cramping or diarrhea during the first weeks of administration. We found no evidence of tolerance to Senna in our review. There is a paucity of information in the literature regarding side effects of sennosides as a long-term therapy, and to our knowledge, this is the first review of Senna side effects in children. Senna induced dermatitis is rare, but may occur when patients need a higher dose. All of the cases described had a long period of exposure of the skin to stool. Besides the perineal rash with blisters, we could find no other described major side effect with Senna administration in the pediatric population or evidence of the frequently mentioned concern of the development of tolerance to Senna. Pediatric caregivers should advise families of the rare side effect of skin blistering and educate them to change the diaper frequently in children who are not toilet- trained to reduce stool to skin exposure. We can conclude from this review that Senna is a safe treatment option for constipation in children. IV. Copyright © 2018 Elsevier Inc. All rights reserved.
Strain Evolution of Annealed Hydrogen-Implanted (0001) Sapphire

NASA Astrophysics Data System (ADS)

Wong, Christine Megan

Exfoliation is a technique used to remove a thin, uniform layer of material from the bulk that involves the annealing of hydrogen ion-implanted materials in order to initiate defect nucleation and growth leading to guided crack propagation. This study presents an investigation into the annealing process required to initiate blistering (an essential precursor to exfoliation) in (0001) sapphire implanted at room temperature with hydrogen ions. Triple axis x-ray diffraction was used to characterize the evolution of the implanted layer for single crystal (0001) sapphire substrates implanted at room temperature at 360 keV with either a 5x1016 cm -2 or 8x1016 cm-2 dose of hydrogen ions. A simulation of the ion distribution in TRIM estimated that the projected range and thickness of the implanted layer for both doses was approximately 2.2 mum. Following implantation, the implanted sapphire was annealed using a two-step annealing procedure. The first step was performed at a lower temperature, ideally to nucleate and coarsen defects. Temperatures investigated ranged from 550 - 650 °C. The second step was performed at a higher temperature (800 °C) to induce further defect coarsening and surface blistering. After all annealing steps, triple axis o/2theta and o scans were taken to observe any changes in the diffraction profile - namely, any reduction in the amplitude and shift in the location of the fringes associated with strain in the crystal - which would correlate with defect growth and nucleation. It was found that significant strain fringe reduction first occurred after annealing at 650 °C for 8 hours for both doses; however, it was not clear whether or not this strain reduction was due primarily to hydrogen diffusion or to recovery of other defects induced during the ion implantation. The o/2theta curves were then fit using Bede RADS in order to quantify the strain within the crystal and confirm the reduction of the strained layer within the crystal. Finally, Nomarski optical images of the sample surfaces were taken after each step to observe any visual changes or blistering that might have occurred. These optical images showed that the strain reduction observed using XRD did not correlate to blistering, as no blisters were observed in any of the optical images. Experimental results showed that at temperatures below 650 °C, no significant strain reduction occurs in hydrogen ion implanted (0001) sapphire. It has also been determined that for (0001) sapphire implanted at room temperature, it was not possible to produce surface blistering after a two-step annealing process at 650 °C and 800 °C, although significant strain reduction did occur, and ? scans showed peak broadening with subsequent annealing, indicating increasing mosaicity and potential defect nucleation. This was in contrast to previous findings that asserted that for sapphire annealed at 650 °C, surface blistering was observable. As previous findings were based on sapphire implanted at elevated temperatures, this may imply that the sapphire substrate reaches a higher temperature than expected during such implantation processes, which may account for the capability for surface blistering at a lower temperature. Conversely, for room temperature ion implantation, temperatures greater than 800 °C may be necessary to first nucleate hydrogen platelet defects and then produce surface blistering.
A diameter distribution approach to estimating average stand dominant height in Appalachian hardwoods

Treesearch

John R. Brooks

2007-01-01

A technique for estimating stand average dominant height based solely on field inventory data is investigated. Using only 45.0919 percent of the largest trees per acre in the diameter distribution resulted in estimates of average dominant height that were within 4.3 feet of the actual value, when averaged over stands of very different structure and history. Cubic foot...
Characterisation of the clinical and activated T cell response to repeat delayed-type hypersensitivity skin challenges in human subjects, with KLH and PPD, as a potential model to test T cell-targeted therapies.

PubMed

Belson, Alexandra; Schmidt, Tim; Fernando, Disala; Hardes, Kelly; Scott, Nicola; Brett, Sara; Clark, Deborah; Oliveira, João Joaquim; Davis, Bill; McHugh, Simon; Stone, John

2016-05-01

To characterise the delayed-type hypersensitivity (DTH) skin reaction to repeated challenges of keyhole limpet hemocyanin (KLH) and tuberculin purified protein derivative (PPD) in healthy volunteers, as a potential model to test T cell-targeted investigational agents. Forty-nine subjects received either KLH, PPD, or PBS repeat skin challenges, and clinical assessments including induration, erythema and Laser Doppler Imaging. Skin biopsies or suction blisters were taken after challenge to investigate the cellular infiltrate of the challenge site, the T cell activation status, as determined by LAG-3 expression, and, specifically for the blister, the concentrations of inflammatory cytokines. Point estimates, estimates of variation and corresponding 95% confidence intervals were constructed for each type of challenge and timepoint. The DTH response could be measured at 48 and 120 h post-KLH and PPD challenge with induration, erythema and Laser Doppler Imaging, with 48 h post-challenge demonstrating the peak of the response. PPD was well tolerated in subjects after multiple challenges, however, a significant number of KLH-treated subjects demonstrated an injection site reaction 6-7 days following the SC injection. PPD demonstrated a boost effect on the second challenge as measured by increased induration, where as this was not noted consistently for KLH. Compared to unchallenged and PBS control-injected skin, increased T cell numbers were detected in the challenge site by both the skin suction blister and biopsy technique, at either time point following KLH or PPD challenge. Use of the T cell activation marker LAG-3 demonstrated the activated phenotype of these cells. In skin blisters, higher numbers of LAG-3+ T cells were detected at 48 h post-challenge, whereas in the biopsies, similar numbers of LAG-3+ cells were observed at both 48 and 120 h. Analysis of blister T cell subpopulations revealed some differences in phenotypes between the time points and between the CD4 and CD8 T cells. Blister cytokine analysis revealed a pro-inflammatory dominated signature in PPD-challenged skin. In summary, our data support the use of a repeat KLH and PPD DTH challenge in clinical trials and that the clinical measures of induration and to a lesser extent erythema are appropriate to monitor the clinical DTH response. Both the blister and biopsy can be utilised to assess and quantify activated T cells and at the dose used, PPD was better tolerated than KLH and hence may be optimal for future studies.
Growth of ponderosa pine stands in relation to mountain pine beetle susceptibility

Treesearch

R. A. Obedzinski; J. M. Schmid; S. A. Mata; W. K. Olsen; R. R. Kessler

1999-01-01

Ten-year diameter and basal area growth were determined for partially cut stands at 4 locations. Average diameters in the partially cut plots generally increased by 1 inch or more, while average diameter in the uncut controls increased by 0.9 inches or less. Individual tree growth is discussed in relation to potential susceptibility to mountain pine beetle infestation...
Cellulosic nanowhiskers. Theory and application of light scattering from polydisperse spheroids in the Rayleigh-Gans-Debye regime.

PubMed

Braun, Birgit; Dorgan, John R; Chandler, John P

2008-04-01

Mathematical treatment of light scattering within the Rayleigh-Gans-Debye limit for spheroids with polydispersity in both length and diameter is developed and experimentally tested using cellulosic nanowhiskers (CNW). Polydispersity indices are obtained by fitting the theoretical formfactor to experimental data. Good agreement is achieved using a polydispersity of 2.3 for the length, independent of the type of acid used. Diameter polydispersities are 2.1 and 3.0 for sulfuric and hydrochloric acids, respectively. These polydispersities allow the determination of average dimensions from the z-average mean-square radius (z) and the weight-average molecular weight (M w) easily obtained from Berry plots. For cotton linter hydrolyzed by hydrochloric acid, the average length and diameter are 244 and 22 nm. This compares to average length and diameter of 272 and 13 nm for sulfuric acid. This study establishes a new light-scattering methodology as a quick and robust tool for size characterization of polydisperse spheroidal nanoparticles.
Safety and effectiveness of cantharidin-podophylotoxin-salicylic acid in the treatment of recalcitrant plantar warts.

PubMed

López López, Daniel; Vilar Fernández, Juan Manuel; Losa Iglesias, Marta Elena; Álvarez Castro, Carlos; Romero Morales, Carlos; García Sánchez, María Matilde; Becerro de Bengoa Vallejo, Ricardo

2016-07-01

The aim of our study was to evaluate the efficacy and safety of topical cantharidin-podophylotoxin-salicylic acid (CPS) treatment of recalcitrant plantar warts (RPW). This study was carried out in a health center in the city of A Coruña (Spain) between January and December 2013. A total of 75 patients completed all the stages of the research process. Information related to treatment with CPS and adverse effects was abstracted from medical records. Of 93 potential patients identified, 75 had at least one follow-up visit or telephone call after treatment and were included in this study. Patients experienced an average of 5.4 visits until complete resolution of their plantar wart occurred, although CPS was not applied at every visit. Fifty-four patients required one application to eliminate the wart and 21 patients required two applications/patient. Seventy-seven percent of patients experienced blistering - an expected therapeutic side effect. All patients experienced some form of an adverse event, the most common being pain (81.3%) and significant blistering (15%). Other side effects were rare (18.7%) and included pruritus, possible mild infection, significant irritation, and bleeding. All patients reported treatment, supporting our results that CPS is a safe and efficacious treatment modality for RPW and should be considered when symptomatic infection necessitates treatment. © 2016 Wiley Periodicals, Inc.
Genetic mapping of Pinus flexilis major gene (Cr4) for resistance to white pine blister rust using transcriptome-based SNP genotyping

Treesearch

Jun-Jun Liu; Anna W. Schoettle; Richard A. Sniezko; Rona N. Sturrock; Arezoo Zamany; Holly Williams; Amanda Ha; Danelle Chan; Bob Danchok; Douglas P. Savin; Angelia Kegley

2016-01-01

Linkage of DNA markers with phenotypic traits provides essential information to dissect clustered genes with potential phenotypic contributions in a target genome region. Pinus flexilis E. James (limber pine) is a keystone five-needle pine species in mountain-top ecosystems of North America. White pine blister rust (WPBR), caused by a non-native fungal...
Chemical Blistering: Cellular and Macromolecular Components

DTIC Science & Technology

1989-12-31

blistering proceeds irrevocably unless the action of the chemical is neutralized within the first several minutes of exposure. Warthin and Weiler (1919...of the pathologic process is set within the first 3 min of exposure in vivo. Warthin and Weiler (1919) found that erythema, inflammation, and...Keratinocyte Culture System Following Exposure to Sulfur Mustard. J. Toxicol. Environ. Health, 23:507-518. Warthin , A.S., Poisoning. C.V. and
The distribution and incidence of white pine blister rust in central and southeastern Wyoming and northern Colorado

Treesearch

Holly S. J. Kearns; William R. Jacobi

2007-01-01

A survey of limber pine (Pinus flexilis James) to determine the geographic distribution, incidence, and severity of white pine blister rust (WPBR) throughout 13 study areas in central and southeastern Wyoming and northern Colorado was conducted from 2002 to 2004. The majority (81.1%) of the 18719 surveyed limber pines>1.37 m tall were classified...
Growing white pine in the Lake States to avoid blister rust

Treesearch

Eugene P. Van Arsdel

1961-01-01

Since white pine is one of the most desirable tree species for the Lake States region, it is unfortunate that fear of the blister rust disease has greatly limited the amount of white pine planted. Research has shown that, in many areas, loss from the disease has not been great even where pine stands have not been protected through ribes eradication. Conversely, in...
Non-Ribes alternate hosts of white pine blister rust: What this discovery means to whitebark pine

Treesearch

Paul J. Zambino; Bryce A. Richardson; Geral I. McDonald; Ned B. Klopfenstein; Mee-Sook Kim

2006-01-01

From early to present-day outbreaks, white pine blister rust caused by the fungus Cronartium ribicola, in combination with mountain pine beetle outbreaks and fire exclusion has caused ecosystem-wide effects for all five-needled pines (McDonald and Hoff 2001). To be successful, efforts to restore whitebark pine will require sound management decisions that incorporate an...
A paradigm shift for white pine blister rust: Non-Ribes alternate hosts for Cronartium ribicola in North America

Treesearch

Paul J. Zambino; Bryce A. Richardson; Geral I. McDonald; Ned B. Klopfenstein; Mee-Sook Kim

2007-01-01

Naturally occurring Cronartium ribicola infections were discovered in August and September, 2004 on Pedicularis racemosa and Castilleja miniata in a mixed stand of white pine blister rust-infected whitebark pine (Pinus albicaulis) and western white pine (P. monticola) in northern Idaho, at Roman Nose Lakes, ca 30 km west of Bonners Ferry. Infections were confirmed by...
Silvical characteristics of balsam fir (Abies balsamea)

Treesearch

Arthur C. Hart

1959-01-01

Balsam fir takes its name from the Latin word for balm. Some people know the tree as the Balm-of-Gilead fir. It has also been called the blister fir, because of the bark blisters that yield Canada balsam, a resin that is used for, among other things, mounting microscope slides. The needles of balsam fir have a spicy aroma that Donald Culross Peattie has called "...
Conservation of biodiversity in sugar pine: effects of the blister rust epidemic on genetic diversity

Treesearch

Constance I. Millar; Bohun B. Kinloch; Robert D. Westfall

1992-01-01

Genetic diversity in sugar plne will be severely reduced by the blister rust pandemic predicted within the next 50 to 75 years. We model effects of the epidemic on genetic diversity at the stand and landscape levels for both natural and artificial regeneration. In natural stands, because natural frequencies of the dominant gene (R) for resistance are low, the most...
4.4.5S: Genetic interactions of white pines and blister rust in western North America

Treesearch

Bohun B. Kinloch Jr.

1998-01-01

A century since its introduction to North America from Europe, white pine blister rust has come to be recognized as one of the catastrophic plant disease epidemics in history. It has yet to stabilize, continuing to spread and intensify. The nine native white pine hosts comprise major timber producers, important watershed protectors, keystone ecological species, and the...
No free lunch: Observations on seed predation, cone collection, and controlled germination of whitebark pine from the Canadian Rockies

Treesearch

Adrian Leslie; Brendan Wilson

2011-01-01

Whitebark pine is a keystone species of high elevation forests in western North America that is experiencing rapid decline due to fire exclusion policies, mountain pine beetle, and the introduced pathogen, white pine blister rust. Restoration activities include collecting cones and growing seedlings from individuals that show mechanisms for resistance to blister rust...
Status of white pine blister rust and seed collections in california's high-elevation white pine species

Treesearch

J. Dunlap

2011-01-01

White pine blister rust (caused by the non-native pathogen Cronartium ribicola) reached northern California about 80 years ago. Over the years its spread southward had been primarily recorded on sugar pine. However, observations on its occurrence had also been reported in several of the higher elevation five-needled white pine species in California. Since the late...
Field levels of infection of progenies of western white pines selected for blister rust resistance

Treesearch

R. J. Steinhoff

1971-01-01

Western white pine trees resulting from crosses of parents selected for phenotypic resistance to Cronartium ribicola J. C. Fisch. ex Rabenh., the white pine blister rust, were inspected for rust infection after 11 to 15 years in two field plots. When compared to controls and to natural reproduction, the progenies of crosses involving trees that exhibited general...

Evidence for a role of eosinophils in blister formation in bullous pemphigoid.

PubMed

de Graauw, E; Sitaru, C; Horn, M; Borradori, L; Yousefi, S; Simon, H-U; Simon, D

2017-07-01

Bullous pemphigoid (BP) is an autoimmune bullous disease of the skin characterized by subepidermal blister formation due to tissue-bound and circulating autoantibodies to the hemidesmosomal antigens BP180 and BP230. Although eosinophils and their toxic mediators are found abundantly in BP lesions, their role in blister formation has remained unclear. To investigate the role of eosinophils in the pathogenesis of BP with a specific focus on blister formation and to define conditions inducing dermal-epidermal separation (DES). In an ex vivo human model of BP, normal human skin cryosections were incubated with purified human peripheral blood eosinophils with or without activation in the presence or absence of BP autoantibodies, brefeldin A, diphenyleneiodonium, DNase or blocking F(ab') 2 fragments to CD16, CD18, CD32 and CD64. Dermal-epidermal separation was assessed by light microscopy studies and quantified using Fiji software. Following activation with IL-5 and in the presence of BP autoantibodies, eosinophils induced separation along the dermal-epidermal junction of ex vivo skin. Dermal-epidermal separation was significantly reduced by blocking any of the following: Fcγ receptor binding (P = 0.048), eosinophil adhesion (P = 0.046), reactive oxygen species (ROS) production (P = 0.002), degranulation (P < 0.0001) or eosinophil extracellular trap (EET) formation (P = 0.048). Our results provide evidence that IL-5-activated eosinophils directly contribute to BP blister formation in the presence of BP autoantibodies. Dermal-epidermal separation by IL-5-activated eosinophils depends on adhesion and Fcγ receptor activation, requires elevated ROS production and degranulation and involves EET formation. Thus, targeting eosinophils may be a promising therapeutic approach for BP. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.
The use of suction blisters to measure sunscreen protection against UVR-induced DNA damage.

PubMed

Josse, Gwendal; Douki, Thierry; Le Digabel, Jimmy; Gravier, Eleonore; Questel, Emmanuel

2018-02-01

The formation of DNA photoproducts caused by solar UVR exposure needs to be investigated in-vivo and in particular in order to assess sunscreens' level of protection against solar genotoxicity. The study's purposes were: i) to evaluate if the roof of suction blisters is an appropriate sampling method for measuring photoproducts, and ii) to measure in-vivo sunscreen protection against cyclobutane pyrimidine dimers. Skin areas on the interior forearms of eight healthy volunteers were exposed in-vivo to 2 MED of simulated solar radiation (SSR) and to 15 MED on a sunscreen protected area. After irradiation, six suction blisters were induced and the blister roofs were collected. Analysis of SSR-induced CPDs was performed by two independent methods: a chromatography coupled to mass spectroscopy (HPLC-MS/MS) approach and a 3D-imaging of CPD immunostaining by multiphoton microscopy on floating epidermal sheets. HPLC-MS/MS analyses showed that SSR-unexposed skin presented no CPD dimers, whereas 2 MED SSR-exposed skin showed a significant number of TT-CPD. The sunscreen covered skin exposed to 15 MED appeared highly protected from DNA damage, as the amount of CPD-dimers remained below the detection limit. The multiphoton-immunostaining analysis consistently showed that no CPD staining was observed on the non-SSR-exposed skin. A significant increase of CPD staining intensity and number of CPD-positive cells were observed on the 2 MED SSR-exposed skin. Sunscreen protected skin presented a very low staining intensity and the number of CPD-positive cells remained very close to non-SSR-exposed skin. This study showed that suction blister samples are very appropriate for measuring CPD dimers in-vivo, and that sunscreens provide high protection against UVR-induced DNA damage. Copyright © 2017 Elsevier B.V. All rights reserved.
Histological observations on needle colonization by Cronartium ribicola in susceptible and resistant seedlings of whitebark pine and limber pine

Treesearch

Jeffrey Stone; Anna Schoettle; Richard Sniezko; Angelia Kegley

2011-01-01

Resistance to white pine blister rust based on a hypersensitive response (HR) that is conferred by a dominant gene has been identified as functioning in needles of blister rust-resistant families of sugar pine, western white pine and southwestern white pine. The typical HR response displays a characteristic local necrosis at the site of infection in the needles during...
"I've got a UFO stuck in my throat!"--an interesting case of foreign body impaction in the oesophagus.

PubMed

Yip, L W; Goh, F S; Sim, R S

1998-03-01

This is a case report of an elderly lady with odynophagia because she accidentally swallowed a tablet which was still wrapped in its blister pack. A discussion of foreign body ingestion, particularly in the elderly, is included. To the authors' knowledge, this is the first paper that includes a lateral cervical radiograph of an ingested blister pack.
Ecology of whitebark pine populations in relation to white pine blister rust infection in subalpine forests of the Lake Tahoe Basin: Implications for restoration

Treesearch

Patricia E. Maloney; Detlev R. Vogler; Camille E. Jensen; Annette Delfino Mix

2012-01-01

For over a century, white pine blister rust (WPBR), caused by the introduced fungal pathogen, Cronartium ribicola J.C. Fisch., has affected white pine (Subgenus Strobus) individuals, populations, and associated forest communities in North America. We surveyed eight populations of whitebark pine (Pinus albicaulis Engelm.) across a range of environmental conditions in...
The Influence of Antiperspirants on Foot-Blister Incidence Following Road Marching.

DTIC Science & Technology

1997-04-01

The influence of antiperspirants on foot blister incidence during road marching was examined in 1,130 cadets from the U.S. Military Academy, West...Point, New York. Cadets were separated into two groups that received either an antiperspirant or placebo preparation, and the study was double blinded...The antiperspirant was a commercially available substance consisting of 20% aluminum chloride hexahydrate in anhydrous ethyl alcohol. The placebo was
A population genetic model for high-elevation five-needle pines: Projecting population outcomes in the presence of white pine blister rust

Treesearch

A. W. Schoettle; J. G. Klutsch; M. F. Antolin; S. Field

2011-01-01

The slow growth and long generation time of the five-needle pines have historically enabled these trees to persist on the landscape for centuries, but without sufficient regeneration opportunities these same traits hinder the species' ability to adapt to novel stresses such as the non-native disease white pine blister rust (WPBR). Increasing the frequency of...
White pine blister rust in northern ldaho and western Montana: alternatives for integrated management

Treesearch

Susan K. Hagle; Geral I. McDonald; Eugene A. Norby

1989-01-01

This report comprises a handbook for managing western white pine in northern ldaho and western Montana, under the threat of white pine blister rust. Various sections cover the history of the disease and efforts to combat it, the ecology of the white pine and Ribes, alternate host of the rust, and techniques for evaluating the rust hazard and attenuating it. The authors...
First report of the white pine blister rust pathogen, Cronartium ribicola, in Arizona

Treesearch

M. L. Fairweather; Brian Geils

2011-01-01

White pine blister rust, caused by Cronartium ribicola J.C. Fisch., was found on southwestern white pine (Pinus flexilis James var. reflexa Engelm., synonym P. strobiformis Engelm.) near Hawley Lake, Arizona (Apache County, White Mountains, 34.024Â°N, 109.776Â°W, elevation 2,357 m) in April 2009. Although white pines in the Southwest (Arizona and New Mexico) have been...
Restoration planting options for limber pines impacted by mountain pine beetles and/or white pine blister rust in the Southern Rocky Mountains

Treesearch

Anne Marie Casper; William R. Jacobi; Anna W. Schoettle; Kelly S. Burns

2010-01-01

Limber Pine (Pinus flexilis) populations in the southern Rock Mountains are severely threatened by the combined impacts of mountain pine beetles and white pine blister rust. Limber pineâs critical role these high elevation ecosystems heightens the importance of mitigating impacts. To develop forest-scale planting methods six seedling planting trial sites were installed...
A Sporadic Neonatal Case of Epidermolysis Bullosa Simplex Generalized Intermediate with KRT5 and KRT14 Gene Mutations

PubMed Central

Wakiguchi, Hiroyuki; Hasegawa, Shunji; Maeba, Shinji; Kimura, Sasagu; Ito, Satoko; Tateishi, Hiroshi; Ueda, Kazuhiro; Ohga, Shouichi

2016-01-01

Background Epidermolysis bullosa simplex (EBS) is a rare genodermatosis resulting from multiple gene mutations, including KRT5 and KRT14. The clinical expression of the mechanobullous skin fragility disease has not been fully explained by the genotype. Case Description An 11-day-old Japanese newborn infant was hospitalized because of herpetiform skin blistering on the feet, which expanded systemically after birth. There was no evidence of virus infection. The biopsied skin lesion showed a blister on the lamina densa without keratin clumps, indicating a diagnosis of EBS-generalized intermediate. We punctured the blisters to remove the contents daily, which led to no exacerbation or infection. The genetic study determined that the patient carried double substitutions of KRT5 c.1424A > G (p.E475G) and KRT14 c.1237G > A (p.A413T). The asymptomatic mother and sister carried the KRT14 substitution, but the healthy father had no substitution of the KRT gene. Conclusion This is the first report of EBS-generalized intermediate in a newborn with de novo KRT5 gene mutation and KRT14 gene polymorphism, and no familial history of epidermolysis. Neonatal blistering due to EBS requires optimal skin management after excluding infectious and immunobullous diseases. PMID:26929861
Provenance study through analysis of microstructural characteristics using an optical microscope and scanning electron microscopy for Goryeo celadon excavated from the seabed.

PubMed

Min-su, Han

2013-08-01

This paper aims at identifying the provenance of Goryeo celadons by understanding its microstructural characteristics, such as particles, blisters, forms and amount of pores, and the presence of crystal formation, bodies, and glazes and its boundary, using an optical microscope and scanning electron microscopy (SEM). The analysis of the reproduced samples shows that the glazed layer of the sherd fired at higher temperatures has lower viscosity and therefore it encourages the blisters to be combined together and the layer to become more transparent. In addition, the result showed that the vitrification and melting process of clay minerals such as feldspars and quartzs on the bodies was accelerated for those samples. To factor such characteristics of the microstructure and apply it to the sherds, the samples could be divided into six categories based on status, such as small particles with many small pores or mainly large and small circular pores in the bodies, only a limited number of varied sized blisters in the glazes, and a few blisters and needle-shaped crystals on the boundary surface. In conclusion, the analysis of the microstructural characteristics using an optical microscope and SEM have proven to be useful as a categorizing reference factor in a provenance study on Goryeo celadons.
The EGF Repeat-Specific O-GlcNAc-Transferase Eogt Interacts with Notch Signaling and Pyrimidine Metabolism Pathways in Drosophila

PubMed Central

Müller, Reto; Jenny, Andreas; Stanley, Pamela

2013-01-01

The O-GlcNAc transferase Eogt modifies EGF repeats in proteins that transit the secretory pathway, including Dumpy and Notch. In this paper, we show that the Notch ligands Delta and Serrate are also substrates of Eogt, that mutation of a putative UDP-GlcNAc binding DXD motif greatly reduces enzyme activity, and that Eogt and the cytoplasmic O-GlcNAc transferase Ogt have distinct substrates in Drosophila larvae. Loss of Eogt is larval lethal and disrupts Dumpy functions, but does not obviously perturb Notch signaling. To identify novel genetic interactions with eogt, we investigated dominant modification of wing blister formation caused by knock-down of eogt. Unexpectedly, heterozygosity for several members of the canonical Notch signaling pathway suppressed wing blister formation. And importantly, extensive genetic interactions with mutants in pyrimidine metabolism were identified. Removal of pyrimidine synthesis alleles suppressed wing blister formation, while removal of uracil catabolism alleles was synthetic lethal with eogt knock-down. Therefore, Eogt may regulate protein functions by O-GlcNAc modification of their EGF repeats, and cellular metabolism by affecting pyrimidine synthesis and catabolism. We propose that eogt knock-down in the wing leads to metabolic and signaling perturbations that increase cytosolic uracil levels, thereby causing wing blister formation. PMID:23671640
Evaluation of haemoglobin in blister fluid as an indicator of paediatric burn wound depth.

PubMed

Tanzer, Catherine; Sampson, Dayle L; Broadbent, James A; Cuttle, Leila; Kempf, Margit; Kimble, Roy M; Upton, Zee; Parker, Tony J

2015-08-01

The early and accurate assessment of burns is essential to inform patient treatment regimens; however, this first critical step in clinical practice remains a challenge for specialist burns clinicians worldwide. In this regard, protein biomarkers are a potential adjunct diagnostic tool to assist experienced clinical judgement. Free circulating haemoglobin has previously shown some promise as an indicator of burn depth in a murine animal model. Using blister fluid collected from paediatric burn patients, haemoglobin abundance was measured using semi-quantitative Western blot and immunoassays. Although a trend was observed in which haemoglobin abundance increased with burn wound severity, several patient samples deviated significantly from this trend. Further, it was found that haemoglobin concentration decreased significantly when whole cells, cell debris and fibrinous matrix was removed from the blister fluid by centrifugation; although the relationship to depth was still present. Statistical analyses showed that haemoglobin abundance in the fluid was more strongly related to the time between injury and sample collection and the time taken for spontaneous re-epithelialisation. We hypothesise that prolonged exposure to the blister fluid microenvironment may result in an increased haemoglobin abundance due to erythrocyte lysis, and delayed wound healing. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.
Effects of air temperature and velocity on the drying kinetics and product particle size of starch from arrowroot (Maranta arundinacae)

NASA Astrophysics Data System (ADS)

Caparanga, Alvin R.; Reyes, Rachael Anne L.; Rivas, Reiner L.; De Vera, Flordeliza C.; Retnasamy, Vithyacharan; Aris, Hasnizah

2017-11-01

This study utilized the 3k factorial design with k as the two varying factors namely, temperature and air velocity. The effects of temperature and air velocity on the drying rate curves and on the average particle diameter of the arrowroot starch were investigated. Extracted arrowroot starch samples were dried based on the designed parameters until constant weight was obtained. The resulting initial moisture content of the arrowroot starch was 49.4%. Higher temperatures correspond to higher drying rates and faster drying time while air velocity effects were approximately negligible or had little effect. Drying rate is a function of temperature and time. The constant rate period was not observed for the drying rate of arrowroot starch. The drying curves were fitted against five mathematical models: Lewis, Page, Henderson and Pabis, Logarithmic and Midili. The Midili Model was the best fit for the experimental data since it yielded the highest R2 and the lowest RSME values for all runs. Scanning electron microscopy (SEM) was used for qualitative analysis and for determination of average particle diameter of the starch granules. The starch granules average particle diameter had a range of 12.06 - 24.60 μm. The use of ANOVA proved that particle diameters for each run varied significantly with each other. And, the Taguchi Design proved that high temperatures yield lower average particle diameter, while high air velocities yield higher average particle diameter.
Increases of Chamber Height and Base Diameter Have Contrasting Effects on Grazing Rate of Two Cladoceran Species: Implications for Microcosm Studies.

PubMed

Pan, Ying; Zhang, Yunshu; Peng, Yan; Zhao, Qinghua; Sun, Shucun

2015-01-01

Aquatic microcosm studies often increase either chamber height or base diameter (to increase water volume) to test spatial ecology theories such as "scale" effects on ecological processes, but it is unclear whether the increase of chamber height or base diameter have the same effect on the processes, i.e., whether the effect of the shape of three-dimensional spaces is significant. We orthogonally manipulated chamber height and base diameter and determined swimming activity, average swimming velocity and grazing rates of the cladocerans Daphnia magna and Moina micrura (on two algae Scenedesmus quadricauda and Chlorella vulgaris; leading to four aquatic algae-cladoceran systems in total) under different microcosm conditions. Across all the four aquatic systems, increasing chamber height at a given base diameter significantly decreased the duration and velocity of horizontal swimming, and it tended to increase the duration but decrease the velocity of vertical swimming. These collectively led to decreases in both average swimming velocity and grazing rate of the cladocerans in the tall chambers (at a given base diameter), in accordance with the positive relationship between average swimming velocity and grazing rate. In contrast, an increase of base diameter at a given chamber height showed contrasting effects on the above parameters. Consistently, at a given chamber volume increasing ratio of chamber height to base diameter decreased the average swimming velocity and grazing rate across all the aquatic systems. In general, increasing chamber depth and base diameter may exert contrasting effects on zooplankton behavior and thus phytoplankton-zooplankton interactions. We suggest that spatial shape plays an important role in determining ecological process and thus should be considered in a theoretical framework of spatial ecology and also the physical setting of aquatic microcosm experiments.
Increases of Chamber Height and Base Diameter Have Contrasting Effects on Grazing Rate of Two Cladoceran Species: Implications for Microcosm Studies

PubMed Central

Pan, Ying; Zhang, Yunshu; Peng, Yan; Zhao, Qinghua; Sun, Shucun

2015-01-01

Aquatic microcosm studies often increase either chamber height or base diameter (to increase water volume) to test spatial ecology theories such as “scale” effects on ecological processes, but it is unclear whether the increase of chamber height or base diameter have the same effect on the processes, i.e., whether the effect of the shape of three-dimensional spaces is significant. We orthogonally manipulated chamber height and base diameter and determined swimming activity, average swimming velocity and grazing rates of the cladocerans Daphnia magna and Moina micrura (on two algae Scenedesmus quadricauda and Chlorella vulgaris; leading to four aquatic algae-cladoceran systems in total) under different microcosm conditions. Across all the four aquatic systems, increasing chamber height at a given base diameter significantly decreased the duration and velocity of horizontal swimming, and it tended to increase the duration but decrease the velocity of vertical swimming. These collectively led to decreases in both average swimming velocity and grazing rate of the cladocerans in the tall chambers (at a given base diameter), in accordance with the positive relationship between average swimming velocity and grazing rate. In contrast, an increase of base diameter at a given chamber height showed contrasting effects on the above parameters. Consistently, at a given chamber volume increasing ratio of chamber height to base diameter decreased the average swimming velocity and grazing rate across all the aquatic systems. In general, increasing chamber depth and base diameter may exert contrasting effects on zooplankton behavior and thus phytoplankton-zooplankton interactions. We suggest that spatial shape plays an important role in determining ecological process and thus should be considered in a theoretical framework of spatial ecology and also the physical setting of aquatic microcosm experiments. PMID:26273836
White pine blister rust at mountain home demonstration state forest: a case study of the epidemic and prospects for genetic control.

Treesearch

Bohun B. Kinloch; Dulitz Jr.

1990-01-01

The behavior of white pine blister rust at Mountain Home State Demonstration Forest and surrounding areas in the southern Sierra Nevada of California indicates that the epidemic has not yet stabilized and that the most likely prognosis is a pandemic on white pines in this region within the next few decades. The impact on sugar pines, from young regeneration to old...
Contact Burn with Blister Formation in Children Treated with Sennosides.

PubMed

Cogley, Kimberly; Echevarria, Andrea; Correa, Catalina; De la Torre-Mondragón, Luis

2017-03-01

Eight children treated for severe constipation with sennosides unexpectedly developed contact burns with blisters secondary to the use of these laxatives. All patients wore diapers, and the injuries occurred overnight. To avoid this side effect, we recommend that patients treated with sennosides, especially those in diapers, receive the medication at a time that allows for bowel movements to occur during the day and not overnight. © 2017 Wiley Periodicals, Inc.
Boat Hull Blisters: Repair Techniques and Long Term Effects on Hull Degradation

DTIC Science & Technology

1988-08-01

Swelling Stresses Produced by Diffusion; Long Term Damage by Water Absorption ; Effects of Gel Coat on Leaching of Water Soluble Material from...leinforcesents 5. Swelling Stresses Produced by Diffusion 6. Long Term Damage by Water Absorption 7. Effects of Gel Coat on Leaching of Water Soluble...the importance of bilge side water pick-up is emphasized. A second method for preventing blister formation is to eliminate or minimize the water soluble

First report of the white pine blister rust fungus, Cronartium ribicola, infecting Pinus flexilis on Pine Mountain, Humboldt National Forest, Elko County, northeastern Nevada, U.S.A.

Treesearch

Detlev R. Vogler; Patricia E. Maloney; Tom Burt; Jacob W. Snelling

2017-01-01

In 2013, while surveying for five-needle white pine cone crops in northeastern Nevada, we observed white pine blister rust, caused by the rust pathogen Cronartium ribicola Fisch., infecting branches and stems of limber pines (Pinus flexilis James) on Pine Mountain (41.76975Â°N, 115.61622Â°W), Humboldt National Forest,...
Effects of Variations in Forebody and Afterbody Dead Rise on the Resistance and Spray Characteristics of the 22ADR Class VPB Airplane: Langley Tank Model 207, TED No. NACA 2361

NASA Technical Reports Server (NTRS)

Clement, Eugene P.; Daniels, Charles J.

1947-01-01

An investigation was made to determine the effects of changes in the amount and distribution of forebody and afterbody dead rise on the hydrodynamic resistance and spray characteristics of a 1/11-size model of the Bureau of Aeronautics design No. 22ADR class VPB airplane. The variations in dead rise within the range investigated had no significant effects on resistance or trim, free to trim, or on resistance or trimming moment, fixed in trim. The coordinates of the peaks of the bow-spray blisters, with reference to the model, were measured at low speeds, and it was found that the model with the low dead rise at the bow had the lowest blisters. The changes in position of the maximum dead rise of the afterbody had no effect on the bow-spray blister.
Oral Manifestations and Dental Management of Epidermolysis Bullosa Simplex.

PubMed

Scheidt, Lisa; Sanabe, Mariane Emi; Diniz, Michele Baffi

2015-01-01

Epidermolysis bullosa (EB) is a group of hereditary chronic disorders, characterized by fragility of the skin and mucous membranes in response to minor mechanical trauma. The objective of this study was to report the case of a young girl diagnosed with epidermolysis bullosa simplex (EBS), transmitted by an autosomal dominant gene. Cutaneous findings included blisters and dystrophy following minimal friction. Recurrent blisters and vesicle formation on the hard palate were the main oral findings. In conclusion, publications concerning the oral and clinical manifestations of EBS are important for providing knowledge and an early multidisciplinary approach that prevents blister formation and improves these patients' quality of life, with the dentist playing an important role in oral health management. How to cite this article: Scheidt L, Sanabe ME, Diniz MB. Oral Manifestations and Dental Management of Epidermolysis Bullosa Simplex. Int J Clin Pediatr Dent 2015;8(3):239-241.
Oral Manifestations and Dental Management of Epidermolysis Bullosa Simplex

PubMed Central

Scheidt, Lisa; Sanabe, Mariane Emi

2015-01-01

ABSTRACT Epidermolysis bullosa (EB) is a group of hereditary chronic disorders, characterized by fragility of the skin and mucous membranes in response to minor mechanical trauma. The objective of this study was to report the case of a young girl diagnosed with epidermolysis bullosa simplex (EBS), transmitted by an autosomal dominant gene. Cutaneous findings included blisters and dystrophy following minimal friction. Recurrent blisters and vesicle formation on the hard palate were the main oral findings. In conclusion, publications concerning the oral and clinical manifestations of EBS are important for providing knowledge and an early multidisciplinary approach that prevents blister formation and improves these patients’ quality of life, with the dentist playing an important role in oral health management. How to cite this article: Scheidt L, Sanabe ME, Diniz MB. Oral Manifestations and Dental Management of Epidermolysis Bullosa Simplex. Int J Clin Pediatr Dent 2015;8(3):239-241. PMID:26604545
A case of bullous dermatitis artefacta possibly induced by a deodorant spray.

PubMed

Ikenaga, Satsuki; Nakano, Hajime; Umegaki, Noriko; Moritsugu, Ryuta; Aizu, Takayuki; Kuribayashi, Michihito; Hanada, Katsumi

2006-01-01

Dermatitis artefacta is one of a spectrum of factitious diseases etiologically responsible for skin lesions denied by patients. These factors often make it difficult to identify the causative agents of the condition. Herein, we report a case of bullous dermatitis artefacta in a 12-year-old girl, for which a deodorant spray was suspected as the probable cause. Pathological examination revealed subepidermal blistering with full-thickness necrosis of the epidermis, suggesting a thermo- or cryo-induced injury. Psychological testing demonstrated her immaturity and dependence. In searching for the causative agent, we suspected a deodorant spray as a blister-inducing agent. We succeeded in reproducing a similar blister lesion on the volunteer's healthy skin using the same spray. Psychiatric involvement significantly complicates the treatment of factitious diseases, including dermatitis artefacta. Cooperation among dermatologists, psychiatrists and the patient's family members is required for ensuring a favorable prognosis.
Study of the mechanical behavior of the hydride blister/rim structure in Zircaloy-4 using in-situ synchrotron X-ray diffraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Jun-li; Han, Xiaochun; Heuser, Brent J.

2016-04-01

High-energy synchrotron X-ray diffraction was utilized to study the mechanical response of the f.c.c delta hydride phase, the intermetallic precipitation with hexagonal C14 lave phase and the alpha-Zr phase in the Zircaloy-4 materials with a hydride rim/blister structure near one surface of the material during in-situ uniaxial tension experiment at 200 degrees C. The f.c.c delta was the only hydride phase observed in the rim/blister structure. The conventional Rietveld refinement was applied to measure the macro-strain equivalent response of the three phases. Two regions were delineated in the applied load versus lattice strain measurement: a linear elastic strain region andmore » region that exhibited load partitioning. Load partitioning was quantified by von Mises analysis. The three phases were observed to have similar elastic modulus at 200 degrees C.« less
Chinese version of the treatment of autoimmune bullous disease quality of life questionnaire: Reliability and validity.

PubMed

Chen, Guo; Yang, Baoqi; Zhang, Zhaoxia; Yang, Qing; Yan, Xiaoxiao; Murrell, Dédée F; Zhang, Furen

2018-01-01

Treatments for autoimmune blistering disease carry significant risks of medical complications and can affect the patient's quality of life. Recently, the Treatment of Autoimmune Bullous Disease Quality of Life questionnaire was developed in Australia. The objective of this study was to evaluate the reliability and validity of the Chinese version of the Treatment of Autoimmune Bullous Disease Quality of Life questionnaire in Chinese patients with autoimmune blistering diseases. The Chinese version of the Treatment of Autoimmune Bullous Disease Quality of Life questionnaire was produced by forward-backward translation and cross-cultural adaptation of the original English version. Autoimmune blistering disease patients recruited in the study self-administered the Chinese Treatment of Autoimmune Bullous Disease Quality of Life questionnaire, the Dermatology Life Quality Index and the 36-item Short-Form Health Survey. Reliability of the Chinese Treatment of Autoimmune Bullous Disease Quality of Life was evaluated using internal consistency and test-retest (days 0 and 7) methods. Validity was analyzed by face, content, construct, convergent and discriminant validity measures. A total of 86 autoimmune blistering disease patients were recruited for the study. Cronbach's alpha coefficient was 0.883 and the intraclass correlation coefficient was 0.871. Face and content validities were satisfactory. Convergent validity testing revealed correlation coefficients of 0.664 for the Treatment of Autoimmune Bullous Disease Quality of Life and Dermatology Life Quality Index and -0.577 for the Treatment of Autoimmune Bullous Disease Quality of Life and 36-item Short-Form Health Survey. With respect to discriminant validity, no significant differences were observed in the Treatment of Autoimmune Bullous Disease Quality of Life scores of men and women (t = 0.251, P = 0.802), inpatients and outpatients (t = 0.447, P = 0.656), patients on steroids and steroid-sparing medications (t = 0.672, P = 0.503) and patients with different autoimmune blistering disease subtypes (F = 0.030, P = 0.971). Illiterate patients were excluded from the study. The patients were from a single hospital and most of their conditions were in a relatively stable status. The Chinese version of the Treatment of Autoimmune Bullous Disease Quality of Life questionnaire is a reliable and valid instrument to measure treatment burden and to serve as an end point in clinical trials in Chinese autoimmune blistering disease patients.
Measurement and interpretation of skin prick test results.

PubMed

van der Valk, J P M; Gerth van Wijk, R; Hoorn, E; Groenendijk, L; Groenendijk, I M; de Jong, N W

2015-01-01

There are several methods to read skin prick test results in type-I allergy testing. A commonly used method is to characterize the wheal size by its 'average diameter'. A more accurate method is to scan the area of the wheal to calculate the actual size. In both methods, skin prick test (SPT) results can be corrected for histamine-sensitivity of the skin by dividing the results of the allergic reaction by the histamine control. The objectives of this study are to compare different techniques of quantifying SPT results, to determine a cut-off value for a positive SPT for histamine equivalent prick -index (HEP) area, and to study the accuracy of predicting cashew nut reactions in double-blind placebo-controlled food challenge (DBPCFC) tests with the different SPT methods. Data of 172 children with cashew nut sensitisation were used for the analysis. All patients underwent a DBPCFC with cashew nut. Per patient, the average diameter and scanned area of the wheal size were recorded. In addition, the same data for the histamine-induced wheal were collected for each patient. The accuracy in predicting the outcome of the DBPCFC using four different SPT readings (i.e. average diameter, area, HEP-index diameter, HEP-index area) were compared in a Receiver-Operating Characteristic (ROC) plot. Characterizing the wheal size by the average diameter method is inaccurate compared to scanning method. A wheal average diameter of 3 mm is generally considered as a positive SPT cut-off value and an equivalent HEP-index area cut-off value of 0.4 was calculated. The four SPT methods yielded a comparable area under the curve (AUC) of 0.84, 0.85, 0.83 and 0.83, respectively. The four methods showed comparable accuracy in predicting cashew nut reactions in a DBPCFC. The 'scanned area method' is theoretically more accurate in determining the wheal area than the 'average diameter method' and is recommended in academic research. A HEP-index area of 0.4 is determined as cut-off value for a positive SPT. However, in clinical practice, the 'average diameter method' is also useful, because this method provides similar accuracy in predicting cashew nut allergic reactions in the DBPCFC. Trial number NTR3572.
Symposium on Toxic Substance Control: Decontamination, April 22 - 24, 1980, Columbus, Ohio.

DTIC Science & Technology

1981-06-01

standard decontaminants is used. TABLE 1. Standard Chemical Decontaminants Decontaminant Agents Used On STB Blister and nerve agents DS-2 All chemical... agents M258 Kit Sodium Hydroxide, Ethanol, G-Series nerve agents Phenol, Water Chloramine B, ZnCI2, Blister ana V-Series Ethanol, Water nerve agents A...is a point source alarm that actively samples ambient air and reacts to low concentrations of nerve agents . The M-8 alarm detector also detects several
Breakdown of major gene resistance to white pine blister rust in sugar pine at Mountain Home Demonstration State Forest: what are the implications?

Treesearch

Jr. Bohun B. Kinloch

1996-01-01

A virulent race of blister rust capable of neutralizing major gene resistance (MGR) in sugar pine made its first appearance nearly two decades ago at a test plantation of resistant sugar pines near Happy Camp, in northern California. Until this year (1996), it had not been found outside the very close neighborhood of this site. Its discovery last summer at Mountain...
Physical stability and resistance to peroxidation of a range of liquid-fill hard gelatin capsule products on extreme long-term storage.

PubMed

Bowtle, William; Kanyowa, Lionel; Mackenzie, Mark; Higgins, Paul

2011-06-01

The industrial take-up of liquid-fill hard capsule technology is limited in part by lack of published long-term physical and chemical stability data which demonstrate the robustness of the system. To assess the effects of extreme long-term storage on liquid-fill capsule product quality and integrity, with respect to both the capsules per se and a standard blister-pack type (foil-film blister). Fourteen sets of stored peroxidation-sensitive liquid-fill hard gelatin capsule product samples, originating ~20 years from the current study, were examined with respect to physical and selected chemical properties, together with microbiological evaluation. All sets retained physical integrity of capsules and blister-packs. Capsules were free of leaks, gelatin cross-linking, and microbiological growth. Eight samples met a limit (anisidine value, 20) commonly used as an index of peroxidation for lipid-based products with shelf lives of 2-3 years. Foil-film blister-packs using PVC or PVC-PVdC as the thermoforming film were well-suited packaging components for the liquid-fill capsule format. The study confirms the long-term physical robustness of the liquid-fill hard capsule format, together with its manufacturing and banding processes. It also indicates that various peroxidation-sensitive products using the capsule format may be maintained satisfactorily over very prolonged storage periods.
Performance of thermal sprayed aluminium coatings in the splash zone and for riser service

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, K.P.; Rosbrook, T.; Thomason, W.H.

1994-12-31

Historically, the coatings used in the splash zone have been either heavy duty coal tar epoxy or a glassflake epoxy. In 1982 Conoco justified a minimum 20 year service life for a sealed thermal sprayed aluminium (TSA) coating for the Hutton TLP risers and tethers. In 1984 the Hutton TLP was installed with 200 microns thickness TSA as the corrosion protection coating and without adding a corrosion allowance. After eight years service the TSA coating on the production risers and tethers is still in good condition. It was noted that the splash zone area was indistinguishable from the remainder ofmore » the inspected components. However, there was a noticeable difference between the production risers and the tethers. The tethers having a vinyl sealer showed a blistered surface while the risers with a silicone sealer did not show any blistering. No corrosion has been observed underneath any of the blisters. The importance of adequate sealers in connection with blistering has been documented by testing. The excellent long term performance of TSA coating in the splash zone has been further documented by the results of field studies published in the last few years. These experiences indicate that TSA coatings properly applied and with the use of specific sealer systems may provide a service life in excess of 30 years with no required maintenance.« less
Studies of phase transitions in the aripiprazole solid dosage form.

PubMed

Łaszcz, Marta; Witkowska, Anna

2016-01-05

Studies of the phase transitions in an active substance contained in a solid dosage form are very complicated but essential, especially if an active substance is classified as a BCS Class IV drug. The purpose of this work was the development of sensitive methods for the detection of the phase transitions in the aripiprazole tablets containing initially its form III. Aripiprazole exhibits polymorphism and pseudopolymorphism. Powder diffraction, Raman spectroscopy and differential scanning calorimetry methods were developed for the detection of the polymorphic transition between forms III and I as well as the phase transition of form III into aripiprazole monohydrate in tablets. The study involved the initial 10 mg and 30 mg tablets, as well as those stored in Al/Al blisters, a triplex blister pack and HDPE bottles (with and without desiccant) under accelerated and long term conditions. The polymorphic transition was not observed in the initial and stored tablets but it was visible on the DSC curve of the Abilify(®) 10 mg reference tablets. The formation of the monohydrate was observed in the diffractograms and Raman spectra in the tablets stored under accelerated conditions. The monohydrate phase was not detected in the tablets stored in the Al/Al blisters under long term conditions. The results showed that the Al/Al blisters can be recommended as the packaging of the aripiprazole tablets containing form III. Copyright © 2015 Elsevier B.V. All rights reserved.
Mast cells play a key role in neutrophil recruitment in experimental bullous pemphigoid

PubMed Central

Chen, Ruoyan; Ning, Gang; Zhao, Ming-Lang; Fleming, Matthew G.; Diaz, Luis A.; Werb, Zena; Liu, Zhi

2001-01-01

Bullous pemphigoid (BP) is an inflammatory subepidermal blistering disease associated with an IgG autoimmune response to the hemidesmosomal protein BP180. Passive transfer of antibodies to the murine BP180 (mBP180) ectodomain triggers a blistering skin disease in mice that depends on complement activation and neutrophil infiltration and closely mimics human BP. In the present study, we show that mast cells (MCs) play a crucial role in experimental BP. Wild-type mice injected intradermally with pathogenic anti-mBP180 IgG exhibited extensive MC degranulation in skin, which preceded neutrophil infiltration and subsequent subepidermal blistering. In contrast, mice genetically deficient in MCs or MC-sufficient mice pretreated with an inhibitor of MC degranulation failed to develop BP. Further, MC-deficient mice reconstituted in skin with MCs became susceptible to experimental BP. Despite the activation of complement to yield C3a and C5a, in the absence of MCs, accumulation of neutrophils at the injection site was blunted. The lack of response due to MC deficiency was overcome by intradermal administration of a neutrophil chemoattractant, IL-8, or by reconstitution of the injection sites with neutrophils. These findings provide the first direct evidence to our knowledge that MCs play an essential role in neutrophil recruitment during subepidermal blister formation in experimental BP. PMID:11602622
Brain Arterial Diameters as a Risk Factor for Vascular Events.

PubMed

Gutierrez, Jose; Cheung, Ken; Bagci, Ahmet; Rundek, Tatjana; Alperin, Noam; Sacco, Ralph L; Wright, Clinton B; Elkind, Mitchell S V

2015-08-06

Arterial luminal diameters are routinely used to assess for vascular disease. Although small diameters are typically considered pathological, arterial dilatation has also been associated with disease. We hypothesize that extreme arterial diameters are biomarkers of the risk of vascular events. Participants in the Northern Manhattan Study who had a time-of-flight magnetic resonance angiography were included in this analysis (N=1034). A global arterial Z-score, called the brain arterial remodeling (BAR) score, was obtained by averaging the measured diameters within each individual. Individuals with a BAR score <-2 SDs were considered to have the smallest diameters, individuals with a BAR score >-2 and <2 SDs had average diameters, and individuals with a BAR score >2 SDs had the largest diameters. All vascular events were recorded prospectively after the brain magnetic resonance imaging. Spline curves and incidence rates were used to test our hypothesis. The association of the BAR score with death (P=0.001), vascular death (P=0.02), any vascular event (P=0.05), and myocardial infarction (P=0.10) was U-shaped except for ischemic stroke (P=0.74). Consequently, incidence rates for death, vascular death, myocardial infarction, and any vascular event were higher in individuals with the largest diameters, whereas individuals with the smallest diameters had a higher incidence of death, vascular death, any vascular event, and ischemic stroke compared with individuals with average diameters. The risk of death, vascular death, and any vascular event increased at both extremes of brain arterial diameters. The pathophysiology linking brain arterial remodeling to systemic vascular events needs further research. © 2015 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley Blackwell.
Estimation of CO2-Equivalent Emission under the Copper Fire Refining Process

NASA Astrophysics Data System (ADS)

Chesnokov, Yu N.; Lisienko, V. G.; Holod, S. I.; Anufriev, V. P.; Lapteva, A. V.

2017-06-01

Non-ferrous metallurgy is one of the most energy-consuming and carbon-emissive sectors of industry. This is due to the fact that the volume of greenhouse gas (GHG) emissions is stipulated by energy consumption. Uralelectromed is a city-forming enterprise of the Verkhnyaya Pyshma. The situation is similar other cities of the old industrial regions of the Russian Federation (Krasnouralsk, Verkhnaya Salda, Karabash, etc.) Verkhnyaya Pyshma has many characteristics of “a clever city”. It can be compared to Hamburg where blister copper is being produced at the center of the city at a copper smelting plant Aurubis. Following the example of such ecologically clean country as Germany and in order to assess how modern energy-efficient low-carbon technologies can provide a favorable habitat, and an acceptable level of carbon footprint, the authors estimated the level of greenhouse gas, i.e., carbon dioxide emission produced by the Uralelectromed. The emission of greenhouse gas -carbon dioxide in the process of fire refining of blister copper has been calculated. The anode melting process consists of several stages where the most important ones are melting of charge, oxidation, and copper melt reduction. Calculations are based on taking into account the mass of burnt carbon of natural gas and the thermal dissociation of fuel oil. It implies that a complete combustion of carbon takes place. The specific value of carbon dioxide emission of the copper refining process is averaged 181 kg CO2 per 1 ton of anode copper.
Sulfur mustard disrupts human α3β1-integrin receptors in concert with α6β4-integrin receptors and collapse of the keratin K5/K14 cytoskeleton

NASA Astrophysics Data System (ADS)

Werrlein, Robert J.; Braue, Catherine R.

2004-06-01

Sulfur mustard (SM; bis(2-chloroethyl) sulfide) is a chemical warfare agent that produces persistent, incapacitating blisters of the skin. The lesions inducing vesication remain elusive, and there is no completely effective treatment. Using mulitphoton microscopy and immunofluorescent staining, we found that exposing human epidermal keratinocytes (HEK) and intact epidermis to SM (400 μm for 5 min) caused progressive collapse of the keratin (K5/K14) cytoskeleton and depletion of α6β integrins. We now report that SM causes concomitant disruption nad collapse of the basal cell's α3β1-integrin receptors. At 1 h postexposure, images of Alexa488-conjugated HEK/α3β1 integrins showed almost complete withdrawal and disappearance of retraction fibers and a progressive loss of polarized mobility. With stero imaging, in vitro expression of this SM effect was characterized by collapse and abutment of adjacent cell membranes. At 2 h postexposure, there was an average 13% dorso-ventral collapse of HEK membranes that paralleled progressive collapse of the K5/K14 cytoskeleton. α3β1 integrin, like α6β4 integrin, is a regulator of cytoskeletal assembly, a receptor for laminin 5 and a mediator of HEK attachment to the basement membrane. Our images indicate that SM disrupts these receptors. We suggest that the progressive disruption destabilizes and potentiates blistering of the epidermal-dermal junction.
Indirect and direct methods for measuring a dynamic throat diameter in a solid rocket motor

NASA Astrophysics Data System (ADS)

Colbaugh, Lauren

In a solid rocket motor, nozzle throat erosion is dictated by propellant composition, throat material properties, and operating conditions. Throat erosion has a significant effect on motor performance, so it must be accurately characterized to produce a good motor design. In order to correlate throat erosion rate to other parameters, it is first necessary to know what the throat diameter is throughout a motor burn. Thus, an indirect method and a direct method for determining throat diameter in a solid rocket motor are investigated in this thesis. The indirect method looks at the use of pressure and thrust data to solve for throat diameter as a function of time. The indirect method's proof of concept was shown by the good agreement between the ballistics model and the test data from a static motor firing. The ballistics model was within 10% of all measured and calculated performance parameters (e.g. average pressure, specific impulse, maximum thrust, etc.) for tests with throat erosion and within 6% of all measured and calculated performance parameters for tests without throat erosion. The direct method involves the use of x-rays to directly observe a simulated nozzle throat erode in a dynamic environment; this is achieved with a dynamic calibration standard. An image processing algorithm is developed for extracting the diameter dimensions from the x-ray intensity digital images. Static and dynamic tests were conducted. The measured diameter was compared to the known diameter in the calibration standard. All dynamic test results were within +6% / -7% of the actual diameter. Part of the edge detection method consists of dividing the entire x-ray image by an average pixel value, calculated from a set of pixels in the x-ray image. It was found that the accuracy of the edge detection method depends upon the selection of the average pixel value area and subsequently the average pixel value. An average pixel value sensitivity analysis is presented. Both the indirect method and the direct method prove to be viable approaches to determining throat diameter during solid rocket motor operation.
PHYSICAL PROPERTIES OF LARGE AND SMALL GRANULES IN SOLAR QUIET REGIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu Daren; Xie Zongxia; Hu Qinghua

The normal mode observations of seven quiet regions obtained by the Hinode spacecraft are analyzed to study the physical properties of granules. An artificial intelligence technique is introduced to automatically find the spatial distribution of granules in feature spaces. In this work, we investigate the dependence of granular continuum intensity, mean Doppler velocity, and magnetic fields on granular diameter. We recognized 71,538 granules by an automatic segmentation technique and then extracted five properties: diameter, continuum intensity, Doppler velocity, and longitudinal and transverse magnetic flux density to describe the granules. To automatically explore the intrinsic structures of the granules in themore » five-dimensional parameter space, the X-means clustering algorithm and one-rule classifier are introduced to define the rules for classifying the granules. It is found that diameter is a dominating parameter in classifying the granules and two families of granules are derived: small granules with diameters smaller than 1.''44, and large granules with diameters larger than 1.''44. Based on statistical analysis of the detected granules, the following results are derived: (1) the averages of diameter, continuum intensity, and Doppler velocity in the upward direction of large granules are larger than those of small granules; (2) the averages of absolute longitudinal, transverse, and unsigned flux density of large granules are smaller than those of small granules; (3) for small granules, the average of continuum intensity increases with their diameters, while the averages of Doppler velocity, transverse, absolute longitudinal, and unsigned magnetic flux density decrease with their diameters. However, the mean properties of large granules are stable; (4) the intensity distributions of all granules and small granules do not satisfy Gaussian distribution, while that of large granules almost agrees with normal distribution with a peak at 1.04 I{sub 0}.« less
Investigation of He-W interactions using DiMES on DIII-D

NASA Astrophysics Data System (ADS)

Doerner, R. P.; Rudakov, D. L.; Chrobak, C. P.; Briesemeister, A. R.; Corr, C.; De Temmerman, G.; Kluth, P.; Lasnier, C. J.; McLean, A. G.; Pace, D. C.; Pitts, R. A.; Schmitz, O.; Thompson, M.; Winters, V.

2016-02-01

Tungsten button samples were exposed to He ELMing H-mode plasma in DIII-D using 2.3 MW of electron cyclotron heating power. Prior to the exposures, the W buttons were exposed to either He, or D, plasma in PISCES-A for 2000 s at surface temperatures of 225-850 °C to create a variety of surfaces (surface blisters, subsurface nano-bubbles, fuzz). Erosion was spectroscopically measured from each DiMES sample, with the exception of the fuzzy W samples which showed almost undetectable WI emission. Post-exposure grazing incidence small angle x-ray scattering surface analysis showed the formation of 1.5 nm diameter He bubbles in the surface of W buttons after only a single DIII-D (3 s, ˜150 ELMs) discharge, similar to the bubble layer resulting from the 2000 s. exposure in PISCES-A. No surface roughening, or damage, was detected on the samples after approximately 600 ELMs with energy density between 0.04-0.1 MJ m-2.

Effects of space environment on structural materials

NASA Technical Reports Server (NTRS)

Miglionico, C.; Stein, C.; Roybal, R.; Robertson, R.; Murr, L. E.; Quinones, S.; Rivas, J.; Marquez, B.; Advani, A. H.; Fisher, W. W.

1992-01-01

A preliminary study of materials exposed in space in a low Earth orbit for nearly six years has revealed a wide range of micrometeorite or microparticle impact craters ranging in size from 1 to 1000 micron in diameter, debris particles from adjacent and distant materials systems, reaction products, and other growth features on the specimen surfaces, and related phenomena. The exposed surface features included fine grained and nearly amorphous materials as well as a large array of single crystal particles. A replication type, lift off technique was developed to remove reaction products and debris from the specimen surfaces in order to isolate them from the background substrate without creating microchemical or microstructural artifacts or alterations. This resulted in surface features resting on a carbon support film which was virtually invisible to observation by electron microscopy and nondispersive x ray analysis. Some evidence for blisters on leading edge aluminum alloy surfaces and a high surface region concentration of oxygen determined by Auger electron spectrometry suggests oxygen effects where fluences exceed 10(exp 21) atoms/sq cm.
Skin breakdown and blisters from senna-containing laxatives in young children.

PubMed

Spiller, Henry A; Winter, Mark L; Weber, Julie A; Krenzelok, Edward P; Anderson, Deborah L; Ryan, Mark L

2003-05-01

At the direction of the Food and Drug Administration, phenolphthalein was removed from all over-the-counter laxatives in 1999. Phenolphthalein was then replaced in most laxative products with the natural product senna from Cassia acutifolia Delile, which contains various anthraquinones. No data are available on the safety of senna use in children <6 years of age. To describe the clinical outcomes of exposure to unintentional ingestion of senna-containing laxatives in young children. All ingestion exposures of senna-containing laxatives in children <5 years of age from 6 poison centers over a 9-month period were evaluated. Inclusion criteria required 24-hour follow-up and the presence of diarrhea to confirm ingestion. Parents were told routinely that severe diaper rash was possible and to protect the perianal area with frequent cleansing and a barrier ointment if the child was wearing diapers. During the study period, 111 cases were reported: 19 children experienced no diarrhea, 4 were lost to follow-up, and 88 exposures were evaluated. Fifty-two children (59%) were
CD94/NKG2C is a killer effector molecule in patients with Stevens-Johnson syndrome and toxic epidermal necrolysis.

PubMed

Morel, Esther; Escamochero, Salvador; Cabañas, Rosario; Díaz, Rosa; Fiandor, Ana; Bellón, Teresa

2010-03-01

Toxic epidermal necrolysis (TEN) and Stevens-Johnson syndrome (SJS) are severe, bullous cutaneous diseases with uncertain pathogenesis, although cytotoxic T cells seem to be involved. Natural killer (NK)-like activity has been found in blister infiltrates. Cytotoxic T lymphocytes (CTLs) with NK-like activity (NK-CTLs) have been shown to express T-cell receptors restricted by the HLA-Ib molecule HLA-E. Alternatively, the HLA-E-specific activating receptor CD94/NKG2C can trigger T-cell receptor-independent cytotoxicity in CTLs. Our aim was to test whether HLA-E expression sensitizes keratinocytes to killing by CTLs with NK-like activity and to explore the expression of activating receptors specific for HLA-E in blister cytotoxic lymphocytes. We used flow cytometry and immunohistochemistry to analyze HLA-E expression in keratinocytes from affected skin in patients with SJS, TEN, and other less severe drug-induced exanthemas. The expression of CD94/NKG2C was analyzed by means of flow cytometry in PBMCs and blister cells from patients. PBMCs and blister cells were analyzed for their ability to kill HLA-E-expressing cells. Involvement of CD94/NKG2C in triggering degranulation of cytolytic cells was explored by means of CD107a mobilization assays and standard cytotoxicity chromium release assays. We found that keratinocytes from affected skin expressed HLA-E and that cell-surface HLA-E sensitizes keratinocytes to killing by CD94/NKG2C(+) CTLs. Frequencies of CD94/NKG2C(+) peripheral blood T and NK cells were increased in patients with SJS and TEN during the acute phase. Moreover, activated blister T and NK lymphocytes expressed CD94/NKG2C and were able to degranulate in response to HLA-E(+) cells in an NKG2C-dependent manner. CD94/NKG2C might be involved in triggering cytotoxic lymphocytes in patients with SJS and TEN.
Department of Defense Chemical, Biological, Defense Program, Annual Report to Congress, March 2005

DTIC Science & Technology

2005-03-01

nerve agents ( GA , GB, GD, and GF), V type nerve agents , and H (mustard) type blister agents . M8 paper can identify agents through...The M21 RSCAAL is an automatic scanning, passive infrared sensor that detects nerve ( GA , GB, and GD) and blister (H and L) agent vapor clouds...Chief of Staff for Programs GA – tabun, a nerve agent GAO – General Accounting Office GB – sarin, a nerve agent GD – soman, a nerve
Conference on Receptor-Based Biosensors (3rd) Held in Aberdeen Proving Ground, Maryland, September 1987

DTIC Science & Technology

1988-07-01

agents throughout the world had mode the threat to U.S. forces an urgent reality, perhaps more so now than ever. The use of blister and nerve agents ...today we have no capability to detect biological organism, toxins, or anything other then the traditional nerve , blood, and blister type agents . For...anticholinesterase. This kind of result was duplicated by Dr. Valdes at his lab at Edgewood. All the nerve agents that we looked at produced this result
Pearling Instabilities of a Viscoelastic Thread

NASA Astrophysics Data System (ADS)

Deblais, A.; Velikov, K. P.; Bonn, D.

2018-05-01

Pearling instabilities of slender viscoelastic threads have received much attention, but remain incompletely understood. We study the instabilities in polymer solutions subject to uniaxial elongational flow. Two distinctly different instabilites are observed: beads on a string and blistering. The beads-on-a-string structure arises from a capillary instability whereas the blistering instability has a different origin: it is due to a coupling between stress and polymer concentration. By varying the temperature to change the solution properties we elucidate the interplay between flow and phase separation.
Acral peeling skin syndrome: a case of two brothers.

PubMed

Wakade, Oojwala; Adams, Beth; Shwayder, Tor

2009-01-01

We report two brothers of Middle Eastern descent with consanguineous parents who present with numerous fragile, flaccid blisters on the hands and feet. In addition to spontaneous peeling, they can manually peel skin from acral areas without pain. The symptoms worsen with warm temperatures, excessive water exposure, and perspiration. Two biopsies from flaccid blisters on the feet were taken from the older brother, which revealed cleavage at the level of the stratum corneum. A diagnosis of acral peeling skin syndrome was made.
The Effect of Substrate Contaminates on the Life of Epoxy Coatings Submerged in Sea Water

DTIC Science & Technology

1991-03-01

contaminants: coal tar, SovaPon, Mare Island and Aquapon . Aquapon is a clear (unpigmented) polyamide epoxy coating. While Aquapon is not normally used for...pigmented coatings. It was found that the Aquapon and coal tar coatings performed similarly, and blistered to the same extent, at the contamination levels...used in the test program. The Sovapon and Mare Island coatings were slightly more resistive to blistering when compared to Aquapon or coal tar but they
Doxycycline versus prednisolone as an initial treatment strategy for bullous pemphigoid: a pragmatic, non-inferiority, randomised controlled trial.

PubMed

Williams, Hywel C; Wojnarowska, Fenella; Kirtschig, Gudula; Mason, James; Godec, Thomas R; Schmidt, Enno; Chalmers, Joanne R; Childs, Margaret; Walton, Shernaz; Harman, Karen; Chapman, Anna; Whitham, Diane; Nunn, Andrew J

2017-04-22

Bullous pemphigoid is a blistering skin disorder with increased mortality. We tested whether a strategy of starting treatment with doxycycline gives acceptable short-term blister control while conferring long-term safety advantages over starting treatment with oral corticosteroids. We did a pragmatic, multicentre, parallel-group randomised controlled trial of adults with bullous pemphigoid (three or more blisters at two or more sites and linear basement membrane IgG or C3). Participants were randomly assigned to doxycycline (200 mg per day) or prednisolone (0·5 mg/kg per day) using random permuted blocks of randomly varying size, and stratified by baseline severity (3-9, 10-30, and >30 blisters for mild, moderate, and severe disease, respectively). Localised adjuvant potent topical corticosteroids (<30 g per week) were permitted during weeks 1-3. The non-inferiority primary effectiveness outcome was the proportion of participants with three or fewer blisters at 6 weeks. We assumed that doxycycline would be 25% less effective than corticosteroids with a 37% acceptable margin of non-inferiority. The primary safety outcome was the proportion with severe, life-threatening, or fatal (grade 3-5) treatment-related adverse events by 52 weeks. Analysis (modified intention to treat [mITT] for the superiority safety analysis and mITT and per protocol for non-inferiority effectiveness analysis) used a regression model adjusting for baseline disease severity, age, and Karnofsky score, with missing data imputed. The trial is registered at ISRCTN, number ISRCTN13704604. Between March 1, 2009, and Oct 31, 2013, 132 patients were randomly assigned to doxycycline and 121 to prednisolone from 54 UK and seven German dermatology centres. Mean age was 77·7 years (SD 9·7) and 173 (68%) of 253 patients had moderate-to-severe baseline disease. For those starting doxycycline, 83 (74%) of 112 patients had three or fewer blisters at 6 weeks compared with 92 (91%) of 101 patients on prednisolone, an adjusted difference of 18·6% (90% CI 11·1-26·1) favouring prednisolone (upper limit of 90% CI, 26·1%, within the predefined 37% margin). Related severe, life-threatening, and fatal events at 52 weeks were 18% (22 of 121) for those starting doxycycline and 36% (41 of 113) for prednisolone (mITT), an adjusted difference of 19·0% (95% CI 7·9-30·1), p=0·001. Starting patients on doxycycline is non-inferior to standard treatment with oral prednisolone for short-term blister control in bullous pemphigoid and significantly safer in the long-term. NIHR Health Technology Assessment Programme. Copyright © 2017 The Author(s). Published by Elsevier Ltd. This is an Open Access article under the CC BY license. Published by Elsevier Ltd.. All rights reserved.
Usefulness of a Simple Immunohistochemical Staining Technique to Differentiate Anti-p200 Pemphigoid From Other Autoimmune Blistering Diseases: A Report of 2 Cases.

PubMed

García-Díez, I; Martínez-Escala, M E; Ishii, N; Hashimoto, T; Mascaró Galy, J M; Pujol, R M; Herrero-González, J E

Anti-p200 pemphigoid is a rare autoimmune subepidermal blistering disease characterized by the presence of circulating immunoglobulin G antibodies directed against laminin gamma-1, a 200-kDa protein located in the lamina lucida of the basement membrane. We review the clinical, histopathological and immunological characteristics of the first 2 cases described in Spain. Anti-p200 pemphigoid shares histopathological and immunopathological findings with epidermolysis bullosa acquisita, the main entity in the differential diagnosis. However, its management follows the same guidelines as those used for bullous pemphigoid. The diagnosis is confirmed by immunoblotting, which is a complex technique available in few centers. We propose the immunohistochemical detection of collagen type IV on the floor of the blister, combined with standard immunofluorescence techniques, as a simple, accessible alternative to differentiate anti-p200 pemphigoid from epidermolysis bullosa acquisita. Copyright © 2016 AEDV. Publicado por Elsevier España, S.L.U. All rights reserved.
The Influence of Anger Expression on Wound Healing

PubMed Central

Gouin, Jean-Philippe; Kiecolt-Glaser, Janice K.; Malarkey, William B.; Glaser, Ronald

2008-01-01

Certain patterns of anger expression have been associated with maladaptive alterations in cortisol secretion, immune functioning, and surgical recovery. We hypothesized that outward and inward anger expression and lack of anger control would be associated with delayed wound healing. A sample of 98 community-dwelling participants received standardized blister wounds on their non-dominant forearm. After blistering, the wounds were monitored daily for eight days to assess speed of repair. Logistic regression was used to distinguish fast and slow healers based on their anger expression pattern. Individuals exhibiting lower levels of anger control were more likely to be categorized as slow healers. The anger control variable predicted wound repair over and above differences in hostility, negative affectivity, social support, and health behaviors. Furthermore, participants with lower levels of anger control exhibited higher cortisol reactivity during the blistering procedure. This enhanced cortisol secretion was in turn related to longer time to heal. These findings suggest that the ability to regulate the expression of one’s anger has a clinically relevant impact on wound healing. PMID:18078737
Blister-inducing antibodies target multiple epitopes on collagen VII in mice

PubMed Central

Csorba, Kinga; Chiriac, Mircea Teodor; Florea, Florina; Ghinia, Miruna Georgiana; Licarete, Emilia; Rados, Andreea; Sas, Alexandra; Vuta, Vlad; Sitaru, Cassian

2014-01-01

Epidermolysis bullosa acquisita (EBA) is an autoimmune subepidermal blistering disease of mucous membranes and the skin caused by autoantibodies against collagen VII. In silico and wet laboratory epitope mapping studies revealed numerous distinct epitopes recognized by EBA patients' autoantibodies within the non-collagenous (NC)1 and NC2 domains of collagen VII. However, the distribution of pathogenic epitopes on collagen VII has not yet been described. In this study, we therefore performed an in vivo functional epitope mapping of pathogenic autoantibodies in experimental EBA. Animals (n = 10/group) immunized against fragments of the NC1 and NC2 domains of collagen VII or injected with antibodies generated against the same fragments developed to different extent experimental EBA. Our results demonstrate that antibodies targeting multiple, distinct epitopes distributed over the entire NC1, but not NC2 domain of collagen VII induce blistering skin disease in vivo. Our present findings have crucial implications for the development of antigen-specific B- and T cell-targeted therapies in EBA. PMID:25091020
The effect of autoimmune blistering diseases on work productivity.

PubMed

Wang, E Q; Radjenovic, M; Castrillón, M A; Feng, G H Y; Murrell, D F

2018-05-06

Autoimmune blistering diseases (AIBD) are known to negatively impact upon quality of life (QoL); however, there is a paucity of research on the effect of AIBD on work productivity. AIBD can be quite disfiguring in terms of a patient's appearance due to their blistering nature. To determine the impact of AIBD on work productivity and to determine whether patients are stigmatized at work due to their appearance. Sixty-one patients with AIBD completed the Work Productivity and Activity Impairment Questionnaire-Specific Health Problem (WPAIQ-SHP), the Dermatology Life Quality Index (DLQI), the Autoimmune Bullous Disease Quality of Life (ABQOL) and the Treatment of Autoimmune Bullous Disease Quality of Life questionnaires (TABQOL). Non-responders to treatment had more work and activity impairment compared to responders. Worse WPAIQ-SHP scores were correlated with higher ABQOL, TABQOL and DLQI scores. Approximately 14.8% of subjects experienced stigmatization at work due to their appearance. The most common body areas stigmatized were easily visible sites, particularly the hands, arms and feet, with the majority of occurrences related to co-workers; for some patients, this stigmatization occurred on a daily basis. Loss of productivity at work was statistically much higher in those with higher disease severity, ABQOL & TABQOL scores and in non-responders to treatment. Autoimmune blistering diseases negatively impacts upon work productivity and activity. Stigmatization was common in the workplace which leads to increased stress, itself a stimulator of pemphigus. © 2018 European Academy of Dermatology and Venereology.
Identifying and exploring physical and psychological morbidity and patient and family caregiver resilience following acute wound development and/or wound blistering post orthopaedic surgery: a systematic review.

PubMed

Ousey, Karen; Edward, Karen-Leigh; Lui, Steve

2015-02-01

The aim of this article was to identify the literature that examined and explored physical and psychological morbidity and patient and family caregiver resilience following acute wound development and/or wound blistering post orthopaedic surgery. A systematic review of the literature using the databases MEDLINE, CINAHL and EMBASE was undertaken. The papers were examined using title and abstract for relevance to the primary and secondary outcomes. The primary outcome of interest was family caregiver resilience following acute wound development and/or wound blistering post orthopaedic surgery. The search yielded 275 records after removing any duplicates; eight studies were considered eligible and were reviewed as full text. Following full review, none of the studies was included in this article. To conclude, there were no papers that investigated or examined the concept of resilience in relation to the management of acute post-surgical orthopaedic wounds. Four of the papers identified, following the review process, did discuss quality of life outcomes and how these may be improved following wound development; most papers focused on the management of chronic wounds. It is apparent from the review that there is no evidence currently available that explores patient and family caregiver resilience following acute wound development and/or wound blistering post orthopaedic surgery. © 2013 The Authors. International Wound Journal © 2013 Medicalhelplines.com Inc and John Wiley & Sons Ltd.
The role of natural killer cells in autoimmune blistering diseases.

PubMed

Zakka, L R; Fradkov, E; Keskin, D B; Tabansky, I; Stern, J N H; Ahmed, A R

2012-02-01

The major focus of this paper is to describe and evaluate current information on the role of natural killer cells (NK cells) in the pathogenesis of blistering diseases. Until now, only pemphigus vulgaris (PV) has been studied. One co-culture study demonstrated that CD4+ T cells from the peripheral blood or perilesional skin of patients with active disease proliferate and secrete cytokines in the presence of major histocompatibility class II-expressing NK cells loaded with antigenic desmoglein self-peptides. Another study showed that NK cells can contribute to a T helper type 2-biased immune response through impaired interleukins (IL)-12 signaling and upregulation of IL, IL-10 and IL-5. Although significant data on other blistering diseases are unavailable at present, some studies implicate NK cells in disease progression. For instance, information on the role of NK cells in psoriasis and their production of tumor necrosis factor-α (TNF-α) will be provided since several TNF-α-inhibitors are used in its treatment. Studies on alopecia areata are also included in this paper because NK cells seem to play a key role in its pathogenesis. This review highlights the potential importance of NK cells and NKT cells as members of the large repertoire of cells and soluble mediators that play a critical role in pathogenesis of blistering diseases and other autoimmune diseases involving the skin. Therefore, the authors advocate a greater focus and interest on the study of the interaction of NK cells and the skin.
Optimization and characterization of high pressure homogenization produced chemically modified starch nanoparticles.

PubMed

Ding, Yongbo; Kan, Jianquan

2017-12-01

Chemically modified starch (RS4) nanoparticles were synthesized through homogenization and water-in-oil mini-emulsion cross-linking. Homogenization was optimized with regard to z-average diameter by using a three-factor-three-level Box-Behnken design. Homogenization pressure (X 1 ), oil/water ratio (X 2 ), and surfactant (X 3 ) were selected as independent variables, whereas z-average diameter was considered as a dependent variable. The following optimum preparation conditions were obtained to achieve the minimum average size of these nanoparticles: 50 MPa homogenization pressure, 10:1 oil/water ratio, and 2 g surfactant amount, when the predicted z-average diameter was 303.6 nm. The physicochemical properties of these nanoparticles were also determined. Dynamic light scattering experiments revealed that RS4 nanoparticles measuring a PdI of 0.380 and an average size of approximately 300 nm, which was very close to the predicted z-average diameter (303.6 nm). The absolute value of zeta potential of RS4 nanoparticles (39.7 mV) was higher than RS4 (32.4 mV), with strengthened swelling power. X-ray diffraction results revealed that homogenization induced a disruption in crystalline structure of RS4 nanoparticles led to amorphous or low-crystallinity. Results of stability analysis showed that RS4 nanosuspensions (particle size) had good stability at 30 °C over 24 h.
Shiitake mushroom production on small diameter oak logs in Ohio

Treesearch

S.M. Bratkovich

1991-01-01

Yields of different strains of shiitake mushrooms (Lentinus edodes) were evaluated when produced on small diameter oak logs in Ohio. Logs averaging between 3-4 inches in diameter were inoculated with four spawn strains in 1985.
Orthopedic stretcher with average-sized person can pass through 18-inch opening

NASA Technical Reports Server (NTRS)

Lothschuetz, F. X.

1966-01-01

Modified Robinson stretcher for vertical lifting and carrying, will pass through an opening 18 inches in diameter, while containing a person of average height and weight. A subject 6 feet tall and weighing 200 pounds was lowered and raised out of an 18 inch diameter opening in a tank to test the stretcher.
Accurate Size and Size-Distribution Determination of Polystyrene Latex Nanoparticles in Aqueous Medium Using Dynamic Light Scattering and Asymmetrical Flow Field Flow Fractionation with Multi-Angle Light Scattering

PubMed Central

Kato, Haruhisa; Nakamura, Ayako; Takahashi, Kayori; Kinugasa, Shinichi

2012-01-01

Accurate determination of the intensity-average diameter of polystyrene latex (PS-latex) by dynamic light scattering (DLS) was carried out through extrapolation of both the concentration of PS-latex and the observed scattering angle. Intensity-average diameter and size distribution were reliably determined by asymmetric flow field flow fractionation (AFFFF) using multi-angle light scattering (MALS) with consideration of band broadening in AFFFF separation. The intensity-average diameter determined by DLS and AFFFF-MALS agreed well within the estimated uncertainties, although the size distribution of PS-latex determined by DLS was less reliable in comparison with that determined by AFFFF-MALS. PMID:28348293
Narrow energy band gap gallium arsenide nitride semi-conductors and an ion-cut-synthesis method for producing the same

DOEpatents

Weng, Xiaojun; Goldman, Rachel S.

2006-06-06

A method for forming a semi-conductor material is provided that comprises forming a donor substrate constructed of GaAs, providing a receiver substrate, implanting nitrogen into the donor substrate to form an implanted layer comprising GaAs and nitrogen. The implanted layer is bonded to the receiver substrate and annealed to form GaAsN and nitrogen micro-blisters in the implanted layer. The micro-blisters allow the implanted layer to be cleaved from the donor substrate.

Failure analysis of blistered gold plating on spot welded electrical relays

NASA Technical Reports Server (NTRS)

Sokolowski, Witold; O'Donnell, Tim

1989-01-01

Gold-plated stainless-steel sideplates, part of a JPL Galileo spacecraft electronic-relay assembly, exhibited blistering after resistance spot welding. Unacceptable relays had heavy nonuniform gold electrodeposited layers with thicknesses 4.5-11.5 microns. SEM and metallographic investigations indicated much higher heat input generated during the resistance spot welding in unacceptable relays. The attributes of acceptable welded relays are contrasted with unacceptable relays; the possible mechanism of laminar formation of polymeric material in the gold plating is discussed; and some recommendations are provided to prevent similar problems.
[Blister dermatitis caused by Epicauta flagellaria (Erichson) (Coleoptera: Meloidae) species].

PubMed

Méndez, E; Sáenz, R E; Johnson, C M

1989-09-01

This paper is the first published report of vesicular dermatitis due to blister beetles of the family Meloidae in Panamá. A familial outbreak of bullous dermatitis caused by Epicauta flagellaria (Erichson) is described. All previous cases known in the Gorgas Memorial Laboratory were associated with E. isthmica Werner. Bullous lesions are produced when cantharidin, a vesicating toxin contained in the beetle's body, is released at the time the insect is crushed or rubbed upon the exposed skin. Rules for the treatment and prevention of this disease are indicated.
Photo-induced toxic epidermal necrolysis caused by clobazam.

PubMed

Redondo, P; Vicente, J; España, A; Subira, M L; De Felipe, I; Quintanilla, E

1996-12-01

Toxic epidermal necrolysis (TEN) is a life-threatening disease, the pathogenesis of which remains largely unknown. We describe a 23-year-old woman under treatment with clobazam who developed lesions of TEN in light-exposed areas. Patch and photopatch tests with clobazam were negative. The cellular phenotype and cytokines were studied in blister fluid. The cellular infiltrate was composed mainly of T lymphocytes with a predominant cytotoxic phenotype. There was an increase in the level of tumour necrosis factor (TNF)-alpha in blister fluid compared with the control (a patient with bullous pemphigoid).
Pill in the blister pack: a rare cause of dysphagia in an elderly adult

PubMed Central

Laeeq, Syed Mudassir; Rai, Ayesha Aslam; Tasneem, Abbas Ali; Luck, Nasir Hassan; Majid, Zain

2015-01-01

Foreign body impaction in the esophagus amongst adults is not a common cause of dysphagia. Fish bone, food bolus, dentures may cause symptoms of dysphagia, odynophagia, chest pain or respiratory distress. It needs prompt evaluation along with removal of the substance either surgically or endoscopically to avoid the development of life threatening complications. Here we are reporting a case of an elderly male, who presented to us with a history of absolute dysphagia for one week, as a consequence of ingestion of a pill in blister pack. PMID:26918072
The Effect of Density on the Height-Diameter Relationship

Treesearch

Boris Zeide; Curtis Vanderschaaf

2002-01-01

Using stand density along with mean diameter to predict average height increases the proportion of explained variance. This result, obtained from permanent plots established in a loblolly pine plantation thinned to different levels, makes sense. We know that due to competition, trees with the same diameter are taller in denser stands. Diameter and density are not only...
The densest loblolly pine stand and its silvicultural implications

Treesearch

Boris Zeide; John Stephens

2010-01-01

Estimation of stand density index has been based on the assumption that the only cause of mortality in fully stocked stands is diameter growth. For example, when average diameter increases by 1 percent, a fixed proportion (1.6 percent) of trees must die, regardless of age, average tree size, and other factors. This balance between growth and mortality entails the...
Correlation between extraocular muscle size and motility restriction in thyroid eye disease.

PubMed

Dagi, Lora R; Zoumalan, Christopher I; Konrad, Hindola; Trokel, Stephen L; Kazim, Michael

2011-01-01

Evaluate the relationship between extraocular muscle (EOM) size, measured by computed tomography, and ocular motility in thyroid eye disease (TED). This case series is based on a retrospective review of the records of 54 patients (108 orbits) with TED. Main outcome measures included EOM size and degree of motility restriction. The average diameter of each rectus muscle was compared with published norms. Four subpopulations based on Age (< 40 or ≥ 40 years) and State of thyroid eye disease (active or stable) were studied. Versions were measured by the corneal light reflex method. The trend of muscle diameter versus motility restriction was evaluated. The average EOM diameter was greater than the norm in the study cohort and 4 subpopulations. The average diameter was largest in the Older and Active TED subpopulations. The inferior rectus and medial rectus were most frequently restricted in the study cohort and 4 subpopulations. The medial rectus had the strongest trend between increasing diameter and motility restriction, followed by the inferior rectus and the superior muscle group (comprised of the superior rectus and levator palpebrae superioris). However, there was a general lack of strong correlation between the diameter of the rectus muscles and their respective motility, especially in the Younger subpopulation. EOM diameters are larger and have more restricted motility in the Older and Active TED subpopulations. Contrary to prior publications, the correlation between EOM diameters and motility was weak, especially in the Younger subpopulation. These findings suggest that the pathophysiology of EOM enlargement is different based upon the age of the patient and the activity of the orbitopathy.
Height-diameter equations for thirteen midwestern bottomland hardwood species

Treesearch

Kenneth C. Colbert; David R. Larsen; James R. Lootens

2002-01-01

Height-diameter equations are often used to predict the mean total tree height for trees when only diameter at breast height (dbh) is measured. Measuring dbh is much easier and is subject to less measurement error than total tree height. However, predicted heights only reflect the average height for trees of a particular diameter. In this study, we present a set of...
The macroscopic delamination of thin films from elastic substrates

PubMed Central

Vella, Dominic; Bico, José; Boudaoud, Arezki; Roman, Benoit; Reis, Pedro M.

2009-01-01

The wrinkling and delamination of stiff thin films adhered to a polymer substrate have important applications in “flexible electronics.” The resulting periodic structures, when used for circuitry, have remarkable mechanical properties because stretching or twisting of the substrate is mostly accommodated through bending of the film, which minimizes fatigue or fracture. To date, applications in this context have used substrate patterning to create an anisotropic substrate-film adhesion energy, thereby producing a controlled array of delamination “blisters.” However, even in the absence of such patterning, blisters appear spontaneously, with a characteristic size. Here, we perform well-controlled experiments at macroscopic scales to study what sets the dimensions of these blisters in terms of the material properties and explain our results by using a combination of scaling and analytical methods. Besides pointing to a method for determining the interfacial toughness, our analysis suggests a number of design guidelines for the thin films used in flexible electronic applications. Crucially, we show that, to avoid the possibility that delamination may cause fatigue damage, the thin film thickness must be greater than a critical value, which we determine. PMID:19556551
Kindler syndrome.

PubMed

Kaviarasan, P K; Prasad, P V S; Shradda; Viswanathan, P

2005-01-01

Kindler syndrome is a rare autosomal recessive disorder associated with skin fragility. It is characterized by blistering in infancy, photosensitivity and progressive poikiloderma. The syndrome involves the skin and mucous membrane with radiological changes. The genetic defect has been identified on the short arm of chromosome 20. This report describes an 18-year-old patient with classical features like blistering and photosensitivity in childhood and the subsequent development of poikiloderma. The differential diagnosis of Kindler syndrome includes diseases like Bloom syndrome, Cockayne syndrome, dyskeratosis congenita, epidermolysis bullosa, Rothmund-Thomson syndrome and xeroderma pigmentosum. Our patient had classical cutaneous features of Kindler syndrome with phimosis as a complication.
Kindler syndrome.

PubMed

Lai-Cheong, Joey E; McGrath, John A

2010-01-01

Kindler syndrome (MIM173650) is an autosomal recessive genodermatosis characterized by poikiloderma, trauma-induced skin blistering, mucosal inflammation, and photosensitivity. Loss-of-function mutations in the FERMT1 gene are the cause of Kindler syndrome. Kindler syndrome is categorized as a subtype of epidermolysis bullosa (EB). During infancy and childhood, there is clinical overlap between Kindler syndrome and dystrophic EB. Unlike other forms of EB, Kindler syndrome is characterized by impaired actin cytoskeleton-extracellular matrix interactions and a variable plane of blister formation at or close to the dermal-epidermal junction. This article reviews clinicopathologic and molecular features of Kindler syndrome and discusses patient management.
Analysis of vesicle fluid following the sting of the lionfish Pterois volitans.

PubMed

Auerbach, P S; McKinney, H E; Rees, R S; Heggers, J P

1987-01-01

Fluid aspirated from blisters following a lionfish (Pterois volitans) sting was analyzed utilizing combined capillary column gas chromatography and negative ion chemical ionization mass spectrometry. Analysis for prostaglandin F2 alpha demonstrated 16.91 ng/ml, for prostaglandin E2 0.143 ng/ml, for 6-keto-prostaglandin F1 alpha less than 0.1 ng/ml (nondetectable) and for thromboxane B2 1.65 ng/ml. Platelet aggregation studies showed that blister fluid caused aggregation of isolated platelets only, which was inhibited by heat treatment or by the presence of normal donor plasma.
Blister pouches for effective reagent storage and release for low cost point-of-care diagnostic applications

NASA Astrophysics Data System (ADS)

Smith, Suzanne; Sewart, Rene; Land, Kevin; Roux, Pieter; Gärtner, Claudia; Becker, Holger

2016-03-01

Lab-on-a-chip devices are often applied to point-of-care diagnostic solutions as they are low-cost, compact, disposable, and require only small sample volumes. For such devices, various reagents are required for sample preparation and analysis and, for an integrated solution to be realized, on-chip reagent storage and automated introduction are required. This work describes the implementation and characterization of effective liquid reagent storage and release mechanisms utilizing blister pouches applied to various point-of-care diagnostic device applications. The manufacturing aspects as well as performance parameters are evaluated.
Seasonal morphological changes in the ovary of the Jungle crow (Corvus macrorhynchos).

PubMed

Islam, Muhammad Nazrul; Zhu, Xiao Bo; Aoyama, Masato; Sugita, Shoei

2010-12-01

Morphometric and histological studies were conducted to examine the seasonal ovarian changes in the Jungle crow of the Kanto area, Japan, from December to June. The ovary weights, largest diameters and atresias of the ovarian follicles and steroid-producing cells were examined. Hematoxylin and eosin-stained ovary sections and ImageJ software were used. The most developed ovary weight increased 373-fold in April, compared to those in December, followed by a 29-fold decrease in June. The average largest follicle diameter of the December and the January ovaries were 1.03 ± 0.35 and 1.05 ± 0.3 mm, respectively. The average largest follicle diameter increased by 2-fold in February, 4-fold in March and 8-fold in April, compared to those of December and January. Thereafter, the average largest follicle diameter declined by 6-fold in June. The average ovary weight and the largest follicle diameter in April increased significantly (P < 0.05) compared to those of December and January, followed by a significant decrease (P < 0.05) in June. The ovary weight correlated well with the expansion of the largest follicular diameter. Non-bursting and bursting atresias of smaller follicles were more common in the December, January, February and June ovaries, and bursting atresias of larger follicles were more common in the March, April and May ovaries. Ovarian steroidogenic cells became heavily charged with lipids in December, January, February and June, and they depleted their lipids in March and April, which might be due to steroid synthesis. Our results indicate that there are significant seasonal histomorphologic variations in the Jungle crow ovary.
Influence of rainfall microstructure on rainfall interception

NASA Astrophysics Data System (ADS)

Zabret, Katarina; Rakovec, Jože; Mikoš, Matjaž; Šraj, Mojca

2016-04-01

Rainfall interception is part of the hydrological cycle. Precipitation, which hits vegetation, is retained on the leaves and branches, from which it eventually evaporates into the atmosphere (interception) or reaches the ground by dripping from the canopy, falling through the gaps (throughfall) and running down the stems (stemflow). The process is influenced by various meteorological and vegetation parameters. Often neglected meteorological parameter influencing rainfall interception is also rainfall microstructure. Rain is a discrete process consisting of various numbers of individual raindrops with different sizes and velocities. This properties describe rainfall microstructure which is often neglected in hydrological analysis and replaced with rainfall intensity. Throughfall, stemflow and rainfall microstructure have been measured since the beginning of the year 2014 under two tree species (Betula pendula and Pinus nigra) on a study plot in Ljubljana, Slovenia. The preliminary analysis of the influence of rainfall microstructure on rainfall interception has been conducted using three events with different characteristics measured in May 2014. Event A is quite short with low rainfall amount and moderate rainfall intensity, whereas events B and C have similar length but low and high intensities, respectively. Event A was observed on the 1st of May 2014. It was 22 minutes long and delivered 1.2 mm of rainfall. The average rainfall intensity was equal to 3.27 mm/h. The event consisted of 1,350 rain drops with average diameter of 1.517 mm and average velocity of 5.110 m/s. Both Betula pendula and Pinus nigra intercepted similar amount of rainfall, 68 % and 69 %, respectively. Event B was observed in the night from the 7th to 8th of May 2014, it was 16 hours and 18 minutes long, and delivered 4.2 mm of rainfall with average intensity of 0.97 mm/h. There were 39,108 raindrops detected with average diameter of 0.858 mm and average velocity of 3.855 m/s. Betula pendula (23 %) has intercepted significantly less rainfall than Pinus nigra (85%). Event C was also observed in the night time between 11th and 12th of May 2014, it lasted 4 hours and 12 minutes and delivered 34.6 mm of rainfall with an average intensity equal to 8.24 mm/h. During the event 147,236 raindrops with average diameter of 1.020 mm and average velocity of 4.078 m/s were detected. Betula pendula has intercepted only 6 % of rainfall whereas Pinus nigra intercepted majority of rainfall, namely 85 %. In case of B. pendula rainfall interception is increasing with higher velocity whereas it is lower for medium diameters than for smaller or larger diameters. Rainfall interception under P. nigra is decreasing with higher velocities and behaving similar as under B. pendula for different diameters but with less obvious difference between diameter classes. We will continue with the measurements and further analysis of several rainfall events will be prepared.
Investigation of He–W interactions using DiMES on DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doerner, R. P.; Rudakov, D. L.; Chrobak, C. P.

Here, tungsten button samples were exposed to He ELMing H-mode plasma in DIII-D using 2.3 MW of electron cyclotron heating power. Prior to the exposures, the W buttons were exposed to either He, or D, plasma in PISCES-A for 2000 s at surface temperatures of 225–850 °C to create a variety of surfaces (surface blisters, subsurface nano-bubbles, fuzz). Erosion was spectroscopically measured from each DiMES sample, with the exception of the fuzzy W samples which showed almost undetectable WI emission. Post-exposure grazing incidence small angle x-ray scattering surface analysis showed the formation of 1.5 nm diameter He bubbles in themore » surface of W buttons after only a single DIII-D (3 s, ~150 ELMs) discharge, similar to the bubble layer resulting from the 2000 s. exposure in PISCES-A. No surface roughening, or damage, was detected on the samples after approximately 600 ELMs with energy density between 0.04–0.1 MJ m –2.« less
Investigation of He–W interactions using DiMES on DIII-D

DOE PAGES

Doerner, R. P.; Rudakov, D. L.; Chrobak, C. P.; ...

2016-01-22

Here, tungsten button samples were exposed to He ELMing H-mode plasma in DIII-D using 2.3 MW of electron cyclotron heating power. Prior to the exposures, the W buttons were exposed to either He, or D, plasma in PISCES-A for 2000 s at surface temperatures of 225–850 °C to create a variety of surfaces (surface blisters, subsurface nano-bubbles, fuzz). Erosion was spectroscopically measured from each DiMES sample, with the exception of the fuzzy W samples which showed almost undetectable WI emission. Post-exposure grazing incidence small angle x-ray scattering surface analysis showed the formation of 1.5 nm diameter He bubbles in themore » surface of W buttons after only a single DIII-D (3 s, ~150 ELMs) discharge, similar to the bubble layer resulting from the 2000 s. exposure in PISCES-A. No surface roughening, or damage, was detected on the samples after approximately 600 ELMs with energy density between 0.04–0.1 MJ m –2.« less
Hierarchically assembled Au microspheres and sea urchin-like architectures: formation mechanism and SERS study

NASA Astrophysics Data System (ADS)

Wang, Xiansong; Yang, Da-Peng; Huang, Peng; Li, Min; Li, Chao; Chen, Di; Cui, Daxiang

2012-11-01

The hierarchically assembled Au microspheres/sea urchin-like structures have been synthesized in aqueous solution at room temperature with and without proteins (bovine serum albumin, BSA) as mediators. The average diameter of an individual Au microsphere is 300-600 nm, which is composed of some compact nanoparticles with an average diameter of about 15 nm. Meanwhile, the sea urchin-like Au architecture exhibits an average diameter of 600-800 nm, which is made up of some nanopricks with an average length of 100-200 nm. These products are characterized by means of scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electronic microscopy (TEM). It is found that the BSA and ascorbic acid (AA) have great effects on the morphology of the resulting products. Two different growth mechanisms are proposed. The study on surface enhanced Raman scattering (SERS) activities is also carried out between Au microspheres and Au sea urchin-like architectures. It is found that Au urchin-like architectures possess much higher SERS activity than the Au microspheres. Our work may shed light on the design and synthesis of hierarchically self-assembled 3D micro/nano-architectures for SERS, catalysis and biosensors.The hierarchically assembled Au microspheres/sea urchin-like structures have been synthesized in aqueous solution at room temperature with and without proteins (bovine serum albumin, BSA) as mediators. The average diameter of an individual Au microsphere is 300-600 nm, which is composed of some compact nanoparticles with an average diameter of about 15 nm. Meanwhile, the sea urchin-like Au architecture exhibits an average diameter of 600-800 nm, which is made up of some nanopricks with an average length of 100-200 nm. These products are characterized by means of scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electronic microscopy (TEM). It is found that the BSA and ascorbic acid (AA) have great effects on the morphology of the resulting products. Two different growth mechanisms are proposed. The study on surface enhanced Raman scattering (SERS) activities is also carried out between Au microspheres and Au sea urchin-like architectures. It is found that Au urchin-like architectures possess much higher SERS activity than the Au microspheres. Our work may shed light on the design and synthesis of hierarchically self-assembled 3D micro/nano-architectures for SERS, catalysis and biosensors. Electronic supplementary information (ESI) available. See DOI: 10.1039/c2nr32405a
Evaluation of diminished microbial contamination in handling of a novel daily disposable flat pack contact lens.

PubMed

Nomachi, Miya; Sakanishi, Kotaro; Ichijima, Hideji; Cavanagh, H Dwight

2013-05-01

To evaluate the efficacy of a novel daily disposable (DD) flat package in regard to microbial contamination on the anterior and posterior surfaces of a contact lens (CL) during handling of the lens for insertion. Four kinds of commercially available general blister-packed daily disposable contact lenses (DD CLs) as controls and a novel Magic 1-day Menicon Flat Pack as a test lens were used for this in vitro study. Lenses were removed from their packages using fingers coated with fluorescein 3 to 5 μm beads or an approximately 7×10(2) to 2×10(3) colony-forming unit (CFU)/mL Staphylococcus aureus suspension. The transfer of fluorescein beads to the surface of the lenses was then observed by fluorescence microscopy. Microbial contamination on the lenses was observed by light microscopy after a 2-day incubation period; and, the number of colonies isolated from the contaminated lenses was determined after 4 days of incubation. The number of fluorescein beads on the Magic lens was significantly less (p<0.05) than that of the general blister-packed control lenses. Adherence of microbial colonies was observed on both inner and outer surfaces of general blister-packed lenses, whereas no colony formation was found on the inner surface of the Magic lens, and the lowest bacterial adherence was observed for the Magic lens. The data demonstrated that placement of the Magic DD lens onto the eye is accompanied by diminished microbial contamination compared with general blister-packed DD CLs. Eye care professionals; however, should instruct patients to comply with intended use of DD CLs to prevent CL-associated microbial keratitis. In all cases, hand washing is mandated prelens insertion.
Helium and deuterium irradiation effects in W-Ta composites produced by pulse plasma compaction

NASA Astrophysics Data System (ADS)

Dias, M.; Catarino, N.; Nunes, D.; Fortunato, E.; Nogueira, I.; Rosinki, M.; Correia, J. B.; Carvalho, P. A.; Alves, E.

2017-08-01

Tungsten-tantalum composites have been envisaged for first-wall components of nuclear fusion reactors; however, changes in their microstructure are expected from severe irradiation with helium and hydrogenic plasma species. In this study, composites were produced from ball milled W powder mixed with 10 at.% Ta fibers through consolidation by pulse plasma compaction. Implantation was carried out at room temperature with He+ (30 keV) or D+ (15 keV) or sequentially with He+ and D+ using ion beams with fluences of 5 × 1021 at/m2. Microstructural changes and deuterium retention in the implanted composites were investigated by scanning electron microscopy, coupled with focused ion beam and energy dispersive X-ray spectroscopy, transmission electron microscopy, X-ray diffraction, Rutherford backscattering spectrometry and nuclear reaction analysis. The composite materials consisted of Ta fibers dispersed in a nanostructured W matrix, with Ta2O5 layers at the interfacial regions. The Ta and Ta2O5 surfaces exhibited blisters after He+ implantation and subsequent D+ implantation worsened the blistering behavior of Ta2O5. Swelling was also pronounced in Ta2O5 where large blisters exhibited an internal nanometer-sized fuzz structure. Transmission electron microscopy revealed an extensive presence of dislocations in the metallic phases after the sequential implantation, while a relatively low density of defects was detected in Ta2O5. This behavior may be partially justified by a shielding effect from the blisters and fuzz structure developed progressively during implantation. The tungsten peaks in the X-ray diffractograms were markedly shifted after He+ implantation, and even more so after the sequential implantation, which is in agreement with the increased D retention inferred from nuclear reaction analysis.

Effects of an introduced pathogen and fire exclusion on the demography of sugar pine

USGS Publications Warehouse

van Mantgem, Phillip J.; Stephenson, Nathan L.; Keifer, MaryBeth; Keeley, Jon E.

2004-01-01

An introduced pathogen, white pine blister rust (Cronartium ribicola), has caused declines in five-needled pines throughout North America. Simultaneously, fire exclusion has resulted in dense stands in many forest types, which may create additional stress for these generally shade-intolerant pines. Fire exclusion also allows fuels to accumulate, and it is unclear how affected populations will respond to the reintroduction of fire. Although white pine blister rust and fire exclusion are widely recognized threats, long-term demographic data that document the effects of these stressors are rare. We present population trends from 2168 individuals over 5–15 years for an affected species, sugar pine (Pinus lambertiana), at several burned and unburned sites in the Sierra Nevada of California. Size-based matrix models indicate that most unburned populations have negative growth rates (λ range: 0.82–1.04). The growth rate of most populations was, however, indistinguishable from replacement levels (λ = 1.0), implying that, if populations are indeed declining, the progression of any such decline is slow, and longer observations are needed to clearly determine population trends. We found significant differences among population growth rates, primarily due to variation in recruitment rates. Deaths associated with blister rust and stress (i.e., resource competition) were common, suggesting significant roles for both blister rust and fire exclusion in determining population trajectories. Data from 15 prescribed fires showed that the immediate effect of burning was the death of many small trees, with the frequency of mortality returning to pre-fire levels within five years. In spite of a poor prognosis for sugar pine, our results suggest that we have time to apply and refine management strategies to protect this species.
Human autoantibodies against a desmosomal core protein in pemphigus foliaceus

PubMed Central

1984-01-01

Pemphigus foliaceus (PF) is a human autoimmune disease in which antibodies are directed against the cell surface of epidermal cells with resultant blister formation. The histopathology of these blisters indicates that cells have detached from each other, and electron microscopy of early blisters shows diminished numbers, to complete loss, of desmosomes as well as abnormalities of the tonofilament- desmosome complex. In this study we demonstrate that autoantibodies from certain PF patients bind to a desmosomal core glycoprotein called desmoglein (DG) I. Proteins in extracts of normal human epidermis were separated by sodium dodecyl sulfate (SDS) polyacrylamide gel electrophoresis (PAGE), then transferred to nitrocellulose or 2- aminophenylthioether paper for immunoperoxidase staining. Results of these immunoblots indicated that sera from 6 of 13 PF patients specifically and intensely stained an approximately 160,000 mol wt polypeptide, "PF antigen". Such staining was not seen with normal human sera or sera from patients with pemphigus vulgaris or bullous pemphigoid, two autoimmune blistering skin diseases that are clinically, histologically, and immunochemically distinct from PF. However, rabbit antiserum directed against DGI, that was isolated from bovine muzzle desmosomes, stained a polypeptide band which co-migrated with PF antigen. Furthermore, when proteins from extracts of normal human epidermis were electrophoresed in two dimensions (isoelectric focusing, then SDS-PAGE) before transfer to nitrocellulose for immunoperoxidase staining, PF antibodies and antibodies to DGI stained identical spots. Finally, PF sera as well as PF IgG that was affinity purified with PF antigen from normal human epidermis, both selectively bound to DGI extracted from bovine muzzle desmosomes. These studies demonstrate that the human autoantibodies from certain patients with PF, a disease of epidermal cell adhesion, are directed against a desmosomal core protein. PMID:6491602
Fabrication of Microfibrous and Nano-/Microfibrous Scaffolds: Melt and Hybrid Electrospinning and Surface Modification of Poly(L-lactic acid) with Plasticizer

PubMed Central

Yoon, Young Il; Park, Ko Eun; Lee, Seung Jin; Park, Won Ho

2013-01-01

Biodegradable poly(L-lactic acid) (PLA) fibrous scaffolds were prepared by electrospinning from a PLA melt containing poly(ethylene glycol) (PEG) as a plasticizer to obtain thinner fibers. The effects of PEG on the melt electrospinning of PLA were examined in terms of the melt viscosity and fiber diameter. Among the parameters, the content of PEG had a more significant effect on the average fiber diameter and its distribution than those of the spinning temperature. Furthermore, nano-/microfibrous silk fibroin (SF)/PLA and PLA/PLA composite scaffolds were fabricated by hybrid electrospinning, which involved a combination of solution electrospinning and melt electrospinning. The SF/PLA (20/80) scaffolds consisted of a randomly oriented structure of PLA microfibers (average fiber diameter = 8.9 µm) and SF nanofibers (average fiber diameter = 820 nm). The PLA nano-/microfiber (20/80) scaffolds were found to have similar pore parameters to the PLA microfiber scaffolds. The PLA scaffolds were treated with plasma in the presence of either oxygen or ammonia gas to modify the surface of the fibers. This approach of controlling the surface properties and diameter of fibers could be useful in the design and tailoring of novel scaffolds for tissue engineering. PMID:24381937
Supercritical multicomponent solvent coal extraction

NASA Technical Reports Server (NTRS)

Corcoran, W. H.; Fong, W. S.; Pichaichanarong, P.; Chan, P. C. F.; Lawson, D. D. (Inventor)

1983-01-01

The yield of organic extract from the supercritical extraction of coal with larger diameter organic solvents such as toluene is increased by use of a minor amount of from 0.1 to 10% by weight of a second solvent such as methanol having a molecular diameter significantly smaller than the average pore diameter of the coal.
Parent artery occlusion for ruptured “true” posterior communicating artery aneurysm

PubMed Central

Takeda, Nobuaki; Oishi, Hidenori; Arai, Hajime

2015-01-01

A case of a patient with a ruptured true posterior communicating artery (PCoA) aneurysm is reported, who had been managed by early endovascular parent artery occlusion with coils. The small blister aneurysm was located at the proximal PCoA itself and directed superiorly. Postoperative course was uneventful. During 1-month follow-up, the patient recovered well and could care for herself. Aneurysms of the PCoA itself are very rare. As reported to date, surgical procedures would favor microsurgical clipping over endovascular coil embolization. Endovascular treatment may be a good alternative to surgical trapping for true PCoA blister aneurysm. PMID:25953771
Retrospective diagnosis of Kindler syndrome in a 37-year-old man.

PubMed

Thomson, M A; Ashton, G H S; McGrath, J A; Eady, R A J; Moss, C

2006-01-01

Kindler syndrome is a rare autosomal recessive disorder characterized by acral blisters in infancy and early childhood, followed by photosensitivity, progressive poikiloderma and cutaneous atrophy. Other features include webbing of the toes and fingers, palmoplantar hyperkeratosis, gingival fragility, poor dentition, and mucosal involvement in the form of urethral, anal and oesophageal stenosis. The recent finding of KIND1 mutations in Kindler syndrome facilitates early diagnosis, prophylactic measures and more precise definition of the phenotype. In the family described here, molecular diagnosis of Kindler syndrome in an infant with acral blisters led to the belated diagnosis in a severely affected relative whose condition had remained unidentified for 37 years.
Paraneoplastic Pemphigus: A Paraneoplastic Autoimmune Multiorgan Syndrome or Autoimmune Multiorganopathy?

PubMed Central

Mahajan, Vikram K.; Sharma, Vikas; Chauhan, Pushpinder S.; Mehta, Karaninder S.; Sharma, Anju Lath; Abhinav, C.; Khatri, Gayatri; Prabha, Neel; Sharma, Saurabh; Negi, Muninder

2012-01-01

Paraneoplastic pemphigus (PNP), a clinically and immunopathologically distinct mucocutaneous blistering dermatosis, is a severe form of autoimmune multiorgan syndrome generally associated with poor therapeutic outcome and high mortality. This IgG-mediated disease is initiated by an obvious or occult lymphoproliferative disorder in most cases. Clinically severe mucositis, and polymorphic blistering skin eruptions, and histologically acantholysis, keratinocyte necrosis and interface dermatitis are its hallmark features. A 58-year-old female presented with recurrent, severe, recalcitrant stomatitis and widespread erosions/blistering lesions of one-year duration. Treatment with repeated courses of systemic corticosteroids at a peripheral center would provide temporary relief. She also had fever, productive cough, odynophagia and poor oral intake, herpes zoster ophthalmicus, pain in the abdomen, and watery diarrhea. An array of investigations revealed chronic lymphocytic leukemia (CLL), mediastinal and para-aortic lymphadenopathy, bronchiolitis obliterans, and vertebral osteoporosis/fractures. With the diagnosis of CLL-associated PNP she was managed with dexamethasone-cyclophosphamide pulse (DCP) therapy for 3 cycles initially, followed by COP regimen (cyclophosphamide, vincristine, and prednisolone) for 5 cycles. Remission is being maintained with chlorambucil and prednisolone pulse therapy once in 3 weeks with complete resolution of skin lesions and adequate control of CLL. PMID:23316398
Churg-Strauss syndrome with coexistence of eosinophilic vasculitis, granulomatous phlebitis and granulomatous dermatitis in bullous pemphigoid-like blisters.

PubMed

Ishibashi, Masafumi; Kudo, Saori; Yamamoto, Kyoko; Shimai, Nobuko; Chen, Ko-Ron

2011-03-01

The main histopathological features in the cutaneous lesions of Churg-Strauss syndrome (CSS) are dermal leukocytoclastic vasculitis with a variable eosinophilic infiltrate and non-vasculitic tissue eosinophilia with granuloma formation. This wide histopathological spectrum may account for the various skin manifestations of CSS. However, the unique histopathological combination of dermal eosinophilic vasculitis and subcutaneous granulomatous phlebitis accompanied by bulla formation has not been previously described. We report an unusual CSS case showing dermal necrotizing eosinophilic vasculitis and granulomatous phlebitis in purpuric lesions coupled with subepidermal blistering. The blisters showed dermal granulomatous dermatitis and eosinophilia without evidence of vasculitis. Dermal necrotizing eosinophilic vasculitis was characterized by fibrinoid alteration of the vessel wall, a prominent perivascular eosinophilic infiltrate, a few infiltrating histiocytes along the affected vessel wall, and the absence of neutrophilic infiltration. The underlying subcutaneous granulomatous phlebitis was characterized by an angiocentric histiocytic infiltrate surrounded by marked eosinophilic infiltrate. Deposition of cytotoxic proteins and radicals derived from eosinophils in the vessel walls and papillary dermis followed by a secondary granulomatous response may account for the unique clinical and histopathological features in this case. Copyright © 2010 John Wiley & Sons A/S.
Subepidermal Blistering Induced by Human Autoantibodies to BP180 Requires Innate Immune Players in a Humanized Bullous Pemphigoid Mouse Model

PubMed Central

Liu, Zhi; Sui, Wen; Zhao, Minglang; Li, Zhuowei; Li, Ning; Thresher, Randy; Giudice, George J.; Fairley, Janet A.; Sitaru, Cassian; Zillikens, Detlef; Ning, Gang; Marinkovich, Peter; Diaz, Luis A.

2008-01-01

Bullous pemphigoid (BP) is a cutaneous autoimmune inflammatory disease associated with subepidermal blistering and autoantibodies against BP180, a transmembrane collagen and major component of the hemidesmosome. Numerous inflammatory cells infiltrate the upper dermis in BP. IgG autoantibodies in BP fix complement and target multiple BP180 epitopes that are highly clustered within a non-collagen linker domain, termed NC16A. Anti-BP180 antibodies induce BP in mice. In this study, we generated a humanized mouse strain, in which the murine BP180NC14A is replaced with the homologous human BP180NC16A epitope cluster region. We show that the humanized NC16A (NC16A+/+) mice injected with anti-BP180NC16A autoantibodies develop BP-like subepidermal blisters. The F(ab′)2 fragments of pathogenic IgG fail to activate complement cascade and are no longer pathogenic. The NC16A+/+ mice pretreated with mast cell activation blocker or depleting of complement or neutrophils become resistant to BP. These findings suggest that the humoral response in BP critically depends on innate immune system players. PMID:18922680
Blistering behavior and deuterium retention in tungsten vanadium alloys exposed to deuterium plasma in the linear plasma device STEP

NASA Astrophysics Data System (ADS)

Wang, Jun; Cheng, Long; Yuan, Yue; Qin, Shao-Yang; Arshad, Kameel; Guo, Wang-Guo; Wang, Zheng; Zhou, Zhang-Jian; Lu, Guang-Hong

2018-03-01

The behavior of tungsten-vanadium (W-V) alloys fabricated by powder metallurgy as a plasma facing material has been studied. W-V alloys with different vanadium concentrations (5 and 10 wt %) manufactured by hot pressing (HP) were exposed to deuterium plasma (flux ∼4.6 × 1021 m-2s-1, fluence ∼5.6 × 1025 m-2, ion energy ∼60 eV, target temperature ∼450 K) in the linear plasma device STEP at Beihang University. Three typical grains are observed on HP sintered W-V alloys and exhibit a significant effect on its performance under deuterium plasma irradiation. Surface blistering only occurs at W-enriched grains and is significantly mitigated in W-V alloys, especially in W-10 V, blistering is completely suppressed. On the other hand, deuterium retention dramatically increases in the W-V alloys due to vanadium addition. The deuterium retention in W-5 wt. % V is about 6.2 times more than that in rolled pure W, and this factor further increases to 6.9 when the V concentration rises to 10 wt %. We ascribe these phenomena to the changes of microstructures and components caused by vanadium addition.
Translation by anisotropic peeling or fracturing in elastic media

NASA Astrophysics Data System (ADS)

Zheng, Zhong; Lister, John; Neufeld, Jerome

2017-11-01

The influence of rock anisotropy on the direction of hydraulic fracturing is an important open question. Two canonical systems have been proposed to investigate the fundamental aspects of such fluid-structure interaction problems: (i) Fluid injection and fracturing into an infinite elastic matrix (e.g., solid gelatin) and (ii) Fluid invasion and peeling beneath a deforming elastic sheet (e.g., bending plate). We investigate the second system and impose a non-uniform prewetting film thickness beneath the elastic sheet. We notice that while the bulk of the elastic sheet retains the static blister shape, a non-uniform prewetting film thickness can cause a horizontal translation of the blister. In particular, for a step jump in prewetting film thickness, asymptotic analysis indicates that, under constant fluid injection, the horizontal translation follows a t 7 / 17 time dependence in cartesian coordinates, and the prefactor of power-law translation depends on the ratio of the distinct prewetting film thicknesses on either side. We also provide numerical and experimental evidence demonstrating anisotropic blister evolution. This can be thought of as a model system for fluid-driven fracturing where the non-uniform prewetting film thickness mimics heterogeneity in material toughness.
A new algorithm for stand table projection models.

Treesearch

Quang V. Cao; V. Clark Baldwin

1999-01-01

The constrained least squares method is proposed as an algorithm for projecting stand tables through time. This method consists of three steps: (1) predict survival in each diameter class, (2) predict diameter growth, and (3) use the least squares approach to adjust the stand table to satisfy the constraints of future survival, average diameter, and stand basal area....
Esophageal lesions following button-battery ingestion in children: Analysis of causes and proposals for preventive measures.

PubMed

Lahmar, J; Célérier, C; Garabédian, E N; Couloigner, V; Leboulanger, N; Denoyelle, F

2018-04-01

To study recent cases of esophageal injury due to button-battery ingestion in children presenting in pediatric ENT emergency departments of the Paris area of France (Île-de-France region), in order to propose appropriate preventive measures. A retrospective descriptive single-center study included all children under 15 years of age, presenting in pediatric ENT emergency departments between January 2008 and April 2014 for button-battery ingestion with esophageal impaction requiring emergency removal. Twenty-two boys and 4 girls, with a median age of 25 months, were included. Twenty-five of the 26 batteries had diameters of 20mm or more. Median esophageal impaction time was 7 hours 30 minutes (range, 2 to 72 hours). The complications rate was 23%. Mean hospital stay cost was €38,751 (range, €5130-119,737). The origin of the battery was known in 23 of the 26 cases: remote control without screw-secured compartment (42.3%), open battery pack (15.4%), children's toy (15.3%), camera (7.7%), watch (1 case) and hearing aid without screw-secured compartment (1 case). Esophageal lesions due to ingestion of button-batteries in children are almost always due to batteries larger than 20mm in diameter, mostly from devices with a poorly protected compartment, or batteries that are not individually packaged. These lesions cause serious complications in a quarter of cases and their management entails high health costs. Legislation requiring screw-secured compartments and individual blisters for batteries could have prevented 69.2% of the ingestions. Copyright © 2017 Elsevier Masson SAS. All rights reserved.
Consideration of growth (age)-related effects on globe size and corneal thickness in ovine eyes for use in laboratory studies.

PubMed

Doughty, Michael J

2017-07-01

The aim was to assess differences in eyeball mass, corneal diameter and central corneal thickness in slaughterhouse-procured ovine eyes. Over a 12-year period, measurements of eye globe mass, horizontal corneal diameter and central corneal thickness were routinely undertaken within two hours post-mortem. Only eyes free of obvious mechanical damage or disease were used. From measurements on 736 quality-selected and trimmed eyes, globe wet mass ranged from 10.4 to 25.2 g, horizontal corneal diameter from 19.0 to 26.5 mm and central corneal thickness measured by ultrasonic pachymetry from 0.543 to 0.836 mm (with an overall average of 690 ± 0.056 mm). The ocular globe mass was strongly correlated to horizontal corneal diameter (r 2 = 0.829). Central corneal thickness correlated with globe mass (r = 0.543) and to horizontal corneal diameter (r = 0.402). Based on the different anatomical measurements, a lamb's eye would be expected to have a thinner cornea (average 0.640 mm) than that of an adult outbred ewe (average 0.730 mm). In freshly procured eyes showing signs of slight corneal oedema, central corneal thickness was greater (average 0.856 ± 0.052 mm) and up to 24 hours of cold storage resulted in predictable increases in central corneal thickness of six to 24 per cent, especially in eyes showing signs of corneal oedema before storage. Based on the correlations obtained, differences in ovine eyes can be attributed to growth-related differences in the animals and thus, indirectly to their expected ages. A simple measure of the horizontal corneal diameter in ovine eyes used for laboratory studies would be a useful indicator in reporting these studies. © 2016 Optometry Australia.
Updating Indiana Annual Forest Inventory and Analysis Plot Data Using Eastern Broadleaf Forest Diameter Growth Models

Treesearch

Veronica C. Lessard

2001-01-01

The Forest Inventory and Analysis (FIA) program of the North Central Research Station (NCRS), USDA Forest Service, has developed nonlinear, individual-tree, distance-independent annual diameter growth models. The models are calibrated for species groups and formulated as the product of an average diameter growth component and a modifier component. The regional models...
Tortuosity correction of Kozeny's hydraulic diameter of a porous medium

NASA Astrophysics Data System (ADS)

Shin, C.

2017-02-01

The hydraulic diameter of a porous medium is the most important characteristic parameter governing porous flow aspects. Kozeny's hydraulic diameter has been used as the representative definition ever since he proposed it in 1927. However, it seems likely that this definition does not perfectly reflect the porous flow features even if the geometric relations of porous media are reasonably considered. Here we reviewed its definition by introducing Darcy's friction flow relation, and discovered that the term "tortuosity" should be included in the definition to more accurately characterize porous flows. Thus, the definition of "Tortuous Hydraulic Diameter (THD)," which corrects Kozeny's hydraulic diameter using tortuosity, is newly presented. Moreover, computational fluid dynamics simulations were performed to check the validity and applicability of the THD approach. As a result, it is seen that the THD demonstrates very low errors, with an average of 1.67%, whereas Kozeny's definition has relatively large errors, with an average of 12.8%. Accordingly, it is confirmed that the THD relation is the more accurate hydraulic diameter definition for a porous medium. Ultimately, the corrected definition can contribute to more reliable determinations of the other characteristic parameters and more reasonable porous flow analyses.
Characterization of fiber diameter using image analysis

NASA Astrophysics Data System (ADS)

Baheti, S.; Tunak, M.

2017-10-01

Due to high surface area and porosity, the applications of nanofibers have increased in recent years. In the production process, determination of average fiber diameter and fiber orientation is crucial for quality assessment. The objective of present study was to compare the relative performance of different methods discussed in literature for estimation of fiber diameter. In this work, the existing automated fiber diameter analysis software packages available in literature were developed and validated based on simulated images of known fiber diameter. Finally, all methods were compared for their reliable and accurate estimation of fiber diameter in electro spun nanofiber membranes based on obtained mean and standard deviation.
Parent artery occlusion for ruptured "true" posterior communicating artery aneurysm.

PubMed

Mitsuhashi, Takashi; Takeda, Nobuaki; Oishi, Hidenori; Arai, Hajime

2015-04-01

A case of a patient with a ruptured true posterior communicating artery (PCoA) aneurysm is reported, who had been managed by early endovascular parent artery occlusion with coils. The small blister aneurysm was located at the proximal PCoA itself and directed superiorly. Postoperative course was uneventful. During 1-month follow-up, the patient recovered well and could care for herself. Aneurysms of the PCoA itself are very rare. As reported to date, surgical procedures would favor microsurgical clipping over endovascular coil embolization. Endovascular treatment may be a good alternative to surgical trapping for true PCoA blister aneurysm. © The Author(s) 2015 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.
Traditional Herbal Remedies for Burn Wound Healing in Canon of Avicenna

PubMed Central

Aliasl, Jale; Khoshzaban, Fariba

2013-01-01

Burns are a worldwide problem. The incidence of severe burns has been higher than the combined incidence of tuberculosis and HIV infections. Throughout history there have been many different treatments prescribed for burns. The Canon is the masterpiece of Avicenna’s medical books. The Canon includes a description of 785 simple drugs. Avicenna believed in burn treatment, which follows two goals. The first goal is prevention of blistering and the second goal is treatment of the burn wound after it has created blisters, cold drugs are suitable for the first goal and dry drugs with moderate in cold and hot qualities are better for second goal, this study reviewed remedies for burn wounds in Canon.
Linear IgA bullous dermatosis in a neonate.

PubMed

Hruza, L L; Mallory, S B; Fitzgibbons, J; Mallory, G B

1993-06-01

A newborn black boy had two facial blisters at birth that progressed to bullous lesions over the trunk, genitals, extremities, and oral and tracheal mucosa. A biopsy specimen demonstrated a subepidermal bulla with mixed eosinophilic and neutrophilic, inflammatory infiltrate. Direct immunofluorescence showed linear IgA, IgG, and C3 depositions along the basement membrane zone, consistent with a diagnosis of childhood linear IgA bullous dermatosis (chronic bullous dermatosis of childhood). The skin disease was controlled with combined prednisone and dapsone. This is the youngest reported patient with the disease. Linear IgA bullous dermatosis should be considered in the differential diagnosis of blistering diseases of the newborn, and immunofluorescence should be performed on a skin biopsy specimen.

Extraction-spectrophotometric determination of traces of gold in copper in silver, lead, blister copper, copper concentrate and anode slime with 4,4'-bis(dimethylamino)-thiobenzophenone.

PubMed

Tsukahara, I

1977-10-01

A sensitive spectrophotometric method has been developed for the determination of gold in copper, silver, lead, blister copper, copper concentrate and anode slime. Optimal conditions have been established for the extraction and determination of gold. Gold is extracted as its bromo complex with tri-n-octylamine and determined photometrically with 4,4'-bis(dimethylamino)thiobenzophenone; the absorbance of the organic phase is measured at 540 nm and the apparent molar absorptivity is about 1.2 x 10(5) 1.mole(-1). cm(-1). As little as 0.1 or 0.2 ppm of gold in these materials can be determined.
Congenital absence of dermatoglyphs.

PubMed

Límová, M; Blacker, K L; LeBoit, P E

1993-08-01

Congenital absence or unusual patterns of human dermatoglyphs (fingerprints) occur in several syndromes that are rare and poorly understood. The abnormalities of dermatoglyphs fall into four categories: complete absence, ridge hypoplasia, ridge dissociation, and ridges-off-the-end. Complete congenital absence of ridges is an exceedingly rare syndrome that consists of neonatal blisters and milia, adult traumatic blistering and fissuring, absence of sweating, contracture of digits, and absence of dermatoglyphs on the hands and feet. The syndrome is inherited in an autosomal dominant pattern, and only two kindreds have been described in the literature. We describe a newly identified patient and kindred with findings similar to the previously reported cases and review the clinical and histopathologic findings of this syndrome.
Beam limiter for thermonuclear fusion devices

DOEpatents

Kaminsky, Manfred S.

1976-01-01

A beam limiter circumscribes the interior surface of a vacuum vessel to inhibit collisions of contained plasma and the vessel walls. The cross section of the material making up the limiter has a flatsided or slightly concave portion of increased width towards the plasma and portions of decreased width towards the interior surface of the vessel. This configuration is designed to prevent a major fraction of the material sputtered, vaporized and blistered from the limiter from reaching the plasma. It also allows adequate heat transfer from the wider to the narrower portions. The preferred materials for the beam limiter are solids of sintered, particulate materials of low atomic number with low vapor pressure and low sputtering and blistering yields.
Aperture averaging in strong oceanic turbulence

NASA Astrophysics Data System (ADS)

Gökçe, Muhsin Caner; Baykal, Yahya

2018-04-01

Receiver aperture averaging technique is employed in underwater wireless optical communication (UWOC) systems to mitigate the effects of oceanic turbulence, thus to improve the system performance. The irradiance flux variance is a measure of the intensity fluctuations on a lens of the receiver aperture. Using the modified Rytov theory which uses the small-scale and large-scale spatial filters, and our previously presented expression that shows the atmospheric structure constant in terms of oceanic turbulence parameters, we evaluate the irradiance flux variance and the aperture averaging factor of a spherical wave in strong oceanic turbulence. Irradiance flux variance variations are examined versus the oceanic turbulence parameters and the receiver aperture diameter are examined in strong oceanic turbulence. Also, the effect of the receiver aperture diameter on the aperture averaging factor is presented in strong oceanic turbulence.
Saccharomyces Boulardii

MedlinePlus

... blisters. High cholesterol. Hives. Lactose intolerance. Lyme disease. Urinary tract infections (UTIs). Yeast infections. Other conditions. More evidence is needed to rate Saccharomyces boulardii for these uses.
A screen to identify Drosophila genes required for integrin-mediated adhesion.

PubMed Central

Walsh, E P; Brown, N H

1998-01-01

Drosophila integrins have essential adhesive roles during development, including adhesion between the two wing surfaces. Most position-specific integrin mutations cause lethality, and clones of homozygous mutant cells in the wing do not adhere to the apposing surface, causing blisters. We have used FLP-FRT induced mitotic recombination to generate clones of randomly induced mutations in the F1 generation and screened for mutations that cause wing blisters. This phenotype is highly selective, since only 14 lethal complementation groups were identified in screens of the five major chromosome arms. Of the loci identified, 3 are PS integrin genes, 2 are blistered and bloated, and the remaining 9 appear to be newly characterized loci. All 11 nonintegrin loci are required on both sides of the wing, in contrast to integrin alpha subunit genes. Mutations in 8 loci only disrupt adhesion in the wing, similar to integrin mutations, while mutations in the 3 other loci cause additional wing defects. Mutations in 4 loci, like the strongest integrin mutations, cause a "tail-up" embryonic lethal phenotype, and mutant alleles of 1 of these loci strongly enhance an integrin mutation. Thus several of these loci are good candidates for genes encoding cytoplasmic proteins required for integrin function. PMID:9755209
Issues around the Prescription of Half Tablets in Northern Switzerland: The Irrational Case of Quetiapine

PubMed Central

Allemann, Samuel S.; Bornand, Delia; Hug, Balthasar; Hersberger, Kurt E.; Arnet, Isabelle

2015-01-01

Background. Prescription of fragmented tablets is useful for individualisation of dose but includes several drawbacks. Although without score lines, the antipsychotic drug quetiapine was in 2011 the most often prescribed 1/2 tablet in discharge prescriptions at the University Hospital in Basel (USB, 671 beds). We aimed at analysing the prescription patterns of split tablets in general and of quetiapine in particular in Switzerland. Methods. All orders of community pharmacies for unit-of-use soft pouch blisters placed at Medifilm AG, the leader company in Switzerland for repackaging into pouch blisters, were analysed. Results. Out of 4,784,999 tablets that were repacked in 2012 in unit-of-use pouch blisters, 8.5% were fragmented, mostly in half (87.6%), and were predominantly psycholeptics (pipamperone 15.8%). Prescription of half quetiapine appears to be a Basel specificity (highest rates of fragments and half quetiapine). Conclusions. Prescription of fragmented tablet is frequent. It represents a safety issue for the patient, and a pharmaceutical care issue for the pharmacist. In ambulatory care, the patient's cognitive and physical capacities must be clarified, suitability of the splitting of the tablet must be checked, appropriate aids must be offered, like a pill-splitting device in order to improve accuracy, and safe use of the drug must be ensured. PMID:26539514
Autoimmune bullous skin diseases. Part 1: Clinical manifestations.

PubMed

Kneisel, Andrea; Hertl, Michael

2011-10-01

Autoimmune bullous skin diseases are characterized by autoantibodies against adhesion molecules of the skin. Pemphigus is a disorder with an intraepidermal loss of adhesion and is characterized by fragile blisters and erosions. Pemphigus vulgaris often shows extensive lesions of the oral mucosa, while pemphigus foliaceus is commonly restricted to cutaneous involvement with puff pastry-like scale formation. Paraneoplastic pemphigus is obligatorily associated with malignancies and often presents as hemorrhagic stomatitis with multiforme-like exanthems. IgA pemphigus typically presents with pustules and annular plaques but not with mucosal involvement. The clinical spectrum of the pemphigoids includes tense blisters, urticarial plaques, and prurigo- like eczematous lesions. Pemphigoid gestationis mostly occurs during the last trimester of pregnancy and mucous membrane pemphigoid primarily involves the oral mucosa and conjunctivae and leads to scarring. Linear IgA bullous dermatosis manifests with tense blisters in a "cluster of jewels"-like pattern in childhood and is more heterogeneous in adulthood. Classical epidermolysis bullosa acquisita shows extensive skin fragility. Dermatitis herpetiformis is associated with gluten-sensitive enteropathy and manifests clinically with severe itching and papulovesicles on the extensor surfaces of the extremities and the lumbosacral area. The intention of the review is to demonstrate the heterogeneous clinical spectrum of autoimmune bullous disorders. © The Authors • Journal compilation © Blackwell Verlag GmbH, Berlin.
Role of different pathways of the complement cascade in experimental bullous pemphigoid

PubMed Central

Nelson, Kelly C.; Zhao, Minglang; Schroeder, Pamela R.; Li, Ning; Wetsel, Rick A.; Diaz, Luis A.; Liu, Zhi

2006-01-01

Bullous pemphigoid (BP) is an autoimmune subepidermal blistering disease associated with autoantibodies directed against the hemidesmosomal proteins BP180 and BP230 and inflammation. Passive transfer of antibodies to the murine BP180 (mBP180) induces a skin disease that closely resembles human BP. In the present study, we defined the roles of the different complement activation pathways in this model system. Mice deficient in the alternative pathway component factor B (Fb) and injected with pathogenic anti-mBP180 IgG developed delayed and less intense subepidermal blisters. Mice deficient in the classical pathway component complement component 4 (C4) and WT mice pretreated with neutralizing antibody against the first component of the classical pathway, C1q, were resistant to experimental BP. These mice exhibited a significantly reduced level of mast cell degranulation and polymorphonuclear neutrophil (PMN) infiltration in the skin. Intradermal administration of compound 48/80, a mast cell degranulating agent, restored BP disease in C4–/– mice. Furthermore, C4–/– mice became susceptible to experimental BP after local injection of PMN chemoattractant IL-8 or local reconstitution with PMNs. These findings provide the first direct evidence to our knowledge that complement activation via the classical and alternative pathways is crucial in subepidermal blister formation in experimental BP. PMID:17024247
Analysis of incidence of bulla formation after tattoo treatment using the combination of the picosecond Alexandrite laser and fractionated CO2 ablation.

PubMed

Au, Sonoa; Liolios, Ana M; Goldman, Mitchel P

2015-02-01

The picosecond Alexandrite laser has shown increased efficacy in tattoo removal in comparison to Q-switched lasers. However, bulla formation is a well-known and expected side effect of this novel treatment and causes patient discomfort. To analyze the incidence of bulla formation after tattoo treatment using the combination of the picosecond Alexandrite laser and fractionated CO2 ablation. This is a retrospective chart review to determine the incidence of bulla formation after laser tattoo removal in 95 patients who were treated with either with the picosecond Alexandrite laser alone or in combination with fractional CO2 ablation. Twenty-six patients (32%) treated with the picosecond laser alone experienced blistering, whereas none of the patients treated with the combination of the picosecond laser and fractionated CO2 ablation experienced blistering. The difference in incidence of bulla formation between the 2 groups was found to be statistically significant (p < .05). This study shows a significant decrease in bulla formation associated with tattoo treatment when fractionated CO2 ablation is added to the picosecond Alexandrite laser, which is consistent with observations from a previous case series. This is important because decreasing extensive blistering likely results in increased patient satisfaction and willingness to return for future treatments.
Comparative study on the in vitro performance of blister molded and conventional lornoxicam immediate release liquitablets: accelerated stability study and anti-inflammatory and ulcerogenic effects.

PubMed

El-Setouhy, Doaa Ahmed; Gamiel, Alaa Abdel-Rahman; Badawi, Alia Abd El-Latif; Osman, Afaf Sayed; Labib, Dina Ahmed

2017-03-01

Lornoxicam is a potent non-steroidal anti-inflammatory drug (NSAID). It shows limited solubility in the gastric pH, delayed bioavailability and pharmacodynamic effects with aggravated gastric side effects (due to longer residence in the stomach wall). To enhance dissolution of lornoxicam in the gastric fluid and expectedly absorption and pharmacological action, with less ulcerogenic effects. Formulation of immediate release (IR) lornoxicam liquitablets containing both liquid and solid release modulators (wetting agent, solubilizers and microenvironmental pH modifiers). Beside the traditional direct compression technique employed for the preparation of liquitablets a new technique, blister molding, was also used. The effect of the two different manufacturing methods on the fast release characteristics (rapid disintegration and dissolution) was studied. Stability and pharmacological activity of the optimum formula were also explored. Similarity factor pointed out the superiority of molding technique in enhancing dissolution of lornoxicam owing to significant crystallinity reduction (XRD). Optimum formula showed negligible change in drug content and dissolution profiles over 12 weeks, significantly improved anti-inflammatory activity and significantly reduced gastric ulcerative effect over pure lornoxicam and commercial formula. Blister molded lornoxicam liquitablet of improved dissolution and pharmacological activity and less gastric erosion was successfully prepared.
The influence of partial cutting on mountain pine beetle-caused tree mortality in Black Hills ponderosa pine stands

Treesearch

J.M. Schmid; S.A. Mata; R.R. Kessler; J.B. Popp

2007-01-01

Ponderosa pine stands were partially cut to various stocking levels at five locations, periodically surveyed, and remeasured during the 20 years after installation. Mean diameter generally increased 2 inches over the 20-year period on most partially cut plots and less than 2 inches on unmanaged controls. Average diameter growth for diameter classes in partially cut...
Picosecond 532-nm neodymium-doped yttrium aluminum garnet laser-a promising modality for the management of verrucous epidermal nevi.

PubMed

Levi, Assi; Amitai, Dan Ben; Mimouni, Daniel; Leshem, Yael A; Arzi, Ofir; Lapidoth, Moshe

2018-04-01

The verrucous epidermal nevus (VEN) is the most common type of epidermal nevi. As lesions can be disfiguring, treatment is often sought. Many therapeutic approaches have been reported, with variable efficacy and safety. Picosecond (PS) lasers are novel laser devices designated to target small chromophores. A side effect of these lasers is blistering due to epidermal-dermal separation. We aimed to harness this side effect of the PS lasers to treat patients with VEN. The purpose of this study was to report our experience treating VEN using a PS 532-nm laser. We present a retrospective case series of six patients with large VEN who were treated using a PS 532-nm laser (2-6 treatments, 8-10 weeks apart). Response in clinical photographs was assessed by two independent dermatologists and graded on a scale of 0 (exacerbation) to 4 (76-100% improvement). Patient satisfaction was recorded on a scale of 1-5. All patients demonstrated significant improvement. Average improvement was 3.7 on the quartile scale of improvement. Patient satisfaction rate averaged 4.7. The PS 532-nm laser is a promising novel modality for the treatment of large VEN.
Complications After Treatment of Head and Neck Venous Malformations With Sodium Tetradecyl Sulfate Foam.

PubMed

Colletti, Giacomo; Deganello, Alberto; Bardazzi, Alessandro; Mattassi, Raul; Dalmonte, Pietro; Gazzabin, Luca; Stillo, Francesco

2017-06-01

The aim of this study was to evaluate complications in patients with head and neck venous malformations (VMs) treated with foam sclerotherapy using sodium tetradecyl sulfate (STS). The authors retrospectively evaluated the complications, pain. and degree of satisfaction in 69 consecutive patients affected by cervicofacial VM managed with STS using the Tessari method in a single institution. The average number of procedures for each patient was 2.1. The most frequent complication was blistering. We observed 1 patient of temporary weakness of a facial nerve branch, 1 paradoxical embolism, and 1 orbital compartment syndrome.The average pain score was 0 (no pain at all) (51.5%). There was no statistically significant correlation between patient satisfaction and the presence of complications or the degree of pain. Sclerotherapy with STS is an effective treatment that yields to very high patient satisfaction. This procedure has an overall low complication rate and is usually effective within a few sessions. However, severe complications may occur; these must be pointed out in the informed consent and the surgeon must be aware of and ready to quickly treat them to prevent long-term sequelae.
Bullosis Diabeticorum: A Rare Presentation with Immunoglobulin G (IgG) Deposition Related Vasculopathy. Case Report and Focused Review

PubMed Central

Sonani, Hardik; Salim, Sohail Abdul; Garla, Vishnu V.; Wile, Anna; Palabindala, Venkataraman

2018-01-01

Patient: Male, 42 Final Diagnosis: Bullosis diabeticorum Symptoms: Skin rash Medication: — Clinical Procedure: Debridement Specialty: Metabolic Disorders and Diabetics Objective: Rare co-existance of disease or pathology Background: Bullosis diabeticorum (BD) is a condition characterized by recurrent, spontaneous, and non-inflammatory blistering in patients with poorly controlled diabetes mellitus. While etiopathogenesis remains unclear, roles of neuropathy, vasculopathy and UV light are hypothesized. Most literature reports negative direct and indirect immunofluorescence findings in diabetics with bullous eruptions. Porphyria cutanea tarda, bullous pemphigoid, epidermolysis bullosa, and pseudoporphyria are other differential diagnoses of bullous lesions, and they must be excluded. Case Report: We present a 42-year-old African American male with long standing poorly controlled insulin dependent diabetes mellitus with blisters on his left hand and feet. The blisters were noticed three weeks prior to presentation and, thereafter, rapidly increased in size and spontaneously ruptured. Physical examination revealed a multitude of both roofed and unroofed bullous painless skin lesions. Hematoxylin and eosin (H&E) staining dramatized the dermal-epidermal blistering and re-epithelization process. Direct Immunofluorescence (DIF) was positive for 2 + IgG deposition in the already thickened basement membrane of the capillaries of the superficial vascular plexus. After debridement, his wounds greatly improved with over three months of aggressive wound care. Conclusions: Primary immunologic abnormality likely plays no role in the onset of BD. To date, only one article has reported nonspecific capillary-associated immunoglobulin M and C3. This is the first case of BD with IgG deposition in the superficial capillary basement membrane. Positive findings on DIF suggest vasculopathy. Dermal microangiopathy, secondary to immunologic abnormality, is a possible underlying pathogenesis to bullae formation. Punch biopsy with DIF can be an additional diagnostic modality in the management of such cases. PMID:29332930
Packaging interventions to increase medication adherence: systematic review and meta-analysis

PubMed Central

Conn, Vicki S.; Ruppar, Todd M.; Chan, Keith C.; Dunbar-Jacob, Jacqueline; Pepper, Ginette A.; De Geest, Sabina

2015-01-01

Objective Inadequate medication adherence is a widespread problem that contributes to increase chronic disease complications and health care expenditures. Packaging interventions using pill boxes and blister packs have been widely recommended to address the medication adherence issue. This meta-analysis review determined the overall effect of packaging interventions on medication adherence and health outcomes. In addition, we tested whether effects vary depending on intervention, sample, and design characteristics. Research design and methods Extensive literature search strategies included examination of 13 computerized databases and 19 research registries, hand searches of 57 journal, and author and ancestry searches. Eligible studies included either pill-boxes or blister packaging interventions to increase medication adherence. Primary study characteristics and outcomes were reliably coded. Random-effects analyses were used to calculate overall effect sizes and conduct moderator analyses. Results Data were synthesized across 22,858 subjects from 52 reports. The overall mean weighted standardized difference effect size for two-group comparisons was 0.593 (favoring treatment over control), which is consistent with the mean of 71% adherence for treatment subjects compared to 63% among control subjects. We found using moderator analyses that interventions were most effective when they used blister packs and were delivered in pharmacies, while interventions were less effective when studies included older subjects and those with cognitive impairment. Methodological moderator analyses revealed significantly larger effect sizes in studies reporting continuous data outcomes instead of dichotomous results and in studies using pharmacy refill medication adherence measures as compared to studies with self-report measures. Conclusions Overall, meta-analysis findings support the use of packaging interventions to effectively increase medication adherence. Limitations of the study include the exclusion of packaging interventions other than pill boxes and blister packs, evidence of publication bias, and primary study sparse reporting of health outcomes and potentially interesting moderating variables such as the number of prescribed medications. PMID:25333709
The occurrence and status of candidate species listed by the US Fish and Wildlife Service on Naval Petroleum Reserve No. 1, Kern County, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-11-01

The distribution and status of four plant and nine animal species being considered by the US Fish and Wildlife Service (FWS) for protection under the Endangered Species Act and one animal species recently listed in the Act as endangered was determined for the Naval Petroleum Reserves in California (NPR-1 and 2). Hoover's woolly-star (Eriastrum hooveri), a Category 2 plant species, was located at 28 sites on NPR-1. The California jewelflower (Caulanthus californicus), Kern mallow (Eremalche kernensis), and San Joaquin woolly-threads (Lembertia congdonii) were not observed. Of these, the Kern mallow is most likely to occur based on habitat utilization andmore » autecology. No evidence was gathered that suggests the Buena Vista Lake shrew (Sorex ornatus relictus) was present on either of the Reserves. Nelson's antelope ground squirrel (Ammospermophilus nelsoni) and the short-nosed kangaroo rat (Dipodomys nitratoides brevinasus) are both Category 2 mammals that were relatively abundant on NPR-1 and 2. The San Joaquin pocket mouse (Perognathus inornatus) was also captured on NPR-1 and 2, but was less numerous. The Tipton kangaroo rat (Dipodomys nitratoides nitratoides), a recently listed endangered species, was found in Section 23S of NPR-1 and Section 18H of NPR-2. No evidence was found that Morrison's blister beetle (Lytta morrisoni), Moestan blister beetle (Lytta moesta), Hopping's blister beetle (Lytta hoppingi), and the Molestan blister beetle (Lytta molesta) exist on either of the Reserves. Similarly, a survey conducted for the striped-skinned snail (Helminthoglypta callistoderma) found no evidence that the snail exists on either of the Reserves. No additional surveys for candidate species that were undetected are needed unless new evidence is collected that suggests the species are or may be present. 17 figs., 7 tabs.« less
Hierarchically assembled Au microspheres and sea urchin-like architectures: formation mechanism and SERS study.

PubMed

Wang, Xiansong; Yang, Da-Peng; Huang, Peng; Li, Min; Li, Chao; Chen, Di; Cui, Daxiang

2012-12-21

The hierarchically assembled Au microspheres/sea urchin-like structures have been synthesized in aqueous solution at room temperature with and without proteins (bovine serum albumin, BSA) as mediators. The average diameter of an individual Au microsphere is 300-600 nm, which is composed of some compact nanoparticles with an average diameter of about 15 nm. Meanwhile, the sea urchin-like Au architecture exhibits an average diameter of 600-800 nm, which is made up of some nanopricks with an average length of 100-200 nm. These products are characterized by means of scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electronic microscopy (TEM). It is found that the BSA and ascorbic acid (AA) have great effects on the morphology of the resulting products. Two different growth mechanisms are proposed. The study on surface enhanced Raman scattering (SERS) activities is also carried out between Au microspheres and Au sea urchin-like architectures. It is found that Au urchin-like architectures possess much higher SERS activity than the Au microspheres. Our work may shed light on the design and synthesis of hierarchically self-assembled 3D micro/nano-architectures for SERS, catalysis and biosensors.
Attenuation-based size metric for estimating organ dose to patients undergoing tube current modulated CT exams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bostani, Maryam, E-mail: mbostani@mednet.ucla.edu; McMillan, Kyle; Lu, Peiyun

2015-02-15

Purpose: Task Group 204 introduced effective diameter (ED) as the patient size metric used to correlate size-specific-dose-estimates. However, this size metric fails to account for patient attenuation properties and has been suggested to be replaced by an attenuation-based size metric, water equivalent diameter (D{sub W}). The purpose of this study is to investigate different size metrics, effective diameter, and water equivalent diameter, in combination with regional descriptions of scanner output to establish the most appropriate size metric to be used as a predictor for organ dose in tube current modulated CT exams. Methods: 101 thoracic and 82 abdomen/pelvis scans frommore » clinically indicated CT exams were collected retrospectively from a multidetector row CT (Sensation 64, Siemens Healthcare) with Institutional Review Board approval to generate voxelized patient models. Fully irradiated organs (lung and breasts in thoracic scans and liver, kidneys, and spleen in abdominal scans) were segmented and used as tally regions in Monte Carlo simulations for reporting organ dose. Along with image data, raw projection data were collected to obtain tube current information for simulating tube current modulation scans using Monte Carlo methods. Additionally, previously described patient size metrics [ED, D{sub W}, and approximated water equivalent diameter (D{sub Wa})] were calculated for each patient and reported in three different ways: a single value averaged over the entire scan, a single value averaged over the region of interest, and a single value from a location in the middle of the scan volume. Organ doses were normalized by an appropriate mAs weighted CTDI{sub vol} to reflect regional variation of tube current. Linear regression analysis was used to evaluate the correlations between normalized organ doses and each size metric. Results: For the abdominal organs, the correlations between normalized organ dose and size metric were overall slightly higher for all three differently (global, regional, and middle slice) reported D{sub W} and D{sub Wa} than they were for ED, but the differences were not statistically significant. However, for lung dose, computed correlations using water equivalent diameter calculated in the middle of the image data (D{sub W,middle}) and averaged over the low attenuating region of lung (D{sub W,regional}) were statistically significantly higher than correlations of normalized lung dose with ED. Conclusions: To conclude, effective diameter and water equivalent diameter are very similar in abdominal regions; however, their difference becomes noticeable in lungs. Water equivalent diameter, specifically reported as a regional average and middle of scan volume, was shown to be better predictors of lung dose. Therefore, an attenuation-based size metric (water equivalent diameter) is recommended because it is more robust across different anatomic regions. Additionally, it was observed that the regional size metric reported as a single value averaged over a region of interest and the size metric calculated from a single slice/image chosen from the middle of the scan volume are highly correlated for these specific patient models and scan types.« less
The analysis of corneal asphericity (Q value) and its related factors of 1,683 Chinese eyes older than 30 years.

PubMed

Xiong, Ying; Li, Jing; Wang, Ningli; Liu, Xue; Wang, Zhao; Tsai, Frank F; Wan, Xiuhua

2017-01-01

To determine corneal Q value and its related factors in Chinese subjects older than 30 years. Cross sectional study. 1,683 participants (1,683 eyes) from the Handan Eye Study were involved, including 955 female and 728 male with average age of 53.64 years old (range from 30 to 107 years). The corneal Q values of anterior and posterior surfaces were measured at 3.0, 5.0 and 7.0mm aperture diameters using Bausch & Lomb Orbscan IIz (software version 3.12). Age, gender and refractive power were recorded. The average Q values of the anterior surface at 3.0, 5.0 and 7.0mm aperture diameters were -0.28±0.18, -0.28±0.18, and -0.29±0.18, respectively. The average Q value of the anterior surface at the 5.0mm aperture diameter was negatively correlated with age (B = -0.003, p<0.01) and the refractive power (B = -0.013, p = 0.016). The average Q values of the posterior surface at 3.0, 5.0, and 7.0mm were -0.26±0.216, -0.26±0.214, and -0.26±0.215, respectively. The average Q value of the posterior surface at the 5.0mm aperture diameter was positively correlated with age (B = 0.002, p = 0.036) and the refractive power (B = 0.016, p = 0.043). The corneal Q value of the elderly Chinese subjects is different from that of previously reported European and American subjects, and the Q value appears to be correlated with age and refractive power.

Growth, chamber building rate and reproduction time of Palaeonummulites venosus under natural conditions.

NASA Astrophysics Data System (ADS)

Kinoshita, Shunichi; Eder, Wolfgang; Wöger, Julia; Hohenegger, Johann; Briguglio, Antonino

2017-04-01

Investigations on Palaeonummulites venosus using the natural laboratory approach for determining chamber building rate, test diameter increase rate, reproduction time and longevity is based on the decomposition of monthly obtained frequency distributions based on chamber number and test diameter into normal-distributed components. The shift of the component parameters 'mean' and 'standard deviation' during the investigation period of 15 months was used to calculate Michaelis-Menten functions applied to estimate the averaged chamber building rate and diameter increase rate under natural conditions. The individual dates of birth were estimated using the inverse averaged chamber building rate and the inverse diameter increase rate fitted by the individual chamber number or the individual test diameter at the sampling date. Distributions of frequencies and densities (i.e. frequency divided by sediment weight) based on chamber building rate and diameter increase rate resulted both in a continuous reproduction through the year with two peaks, the stronger in May /June determined as the beginning of the summer generation (generation1) and the weaker in November determined as the beginning of the winter generation (generation 2). This reproduction scheme explains the existence of small and large specimens in the same sample. Longevity, calculated as the maximum difference in days between the individual's birth date and the sampling date seems to be round about one year, obtained by both estimations based on the chamber building rate and the diameter increase rate.
Harvesting Productionin Uneven-Aged Loblolly-Shortleaf Pine Stands:The Crossett Farm Forestry Forties

Treesearch

R. Kluender; B. Stokes; S. Woodfin

1992-01-01

Twostands managed using uneven-aged techniques werehar- vested aspar-t of a5-year entry schedule. Felling and skidding productivity varied significantly with average stem diameter and volume and was affected by diameter distribution of the removed material.
Development of the Statocyst in the Freshwater Snail Biomphalaria Glabrata (Pulmonata, Basommatophora)

NASA Technical Reports Server (NTRS)

Gao, Wenyuan; Wiederhold, Michael; Hejl, Robert

1997-01-01

The development of the statocyst of the freshwater snail Biomphalaria glabrata has been examined from embryo to adult. Special emphasis was put on the growth of the statoconia in the statocysts. In the statocysts of embryonic snails (90-120 h after oviposition) there is not a single statolith but an average of 40-50 statoconia per statocyst. The number of statoconia increases to 385-400 when the snails reach a shell diameter of 4 mm and remains relatively constant thereafter, irrespective of shell size. Small statoconia are found in supporting cells, which suggests that the statoconia are produced within these cells. The average diameter of statoconia and the total mass of statoconia increase with increasing shell diameter. The average number of large statoconia (diameter greater than 7 micrometers) per statocyst continues to increase from 2 to 10 mm animals while the number of small ones (diameter less than 4 micrometers) initially rises and then decreases after 4 mm. These results demonstrate continuous growth of the statoconia in the cyst lumen of Biomphalaria. The single statoconia vibrate in a regular pattern in vivo, indicating beating of the statocyst cilia. The statoconia sink under the influence of gravity to load and stimulate receptor cells which are at the bottom. The length of cilia and the size of statocyst gradually increase as the animal grows. However, the increase in the volume of the statocyst is relatively small compared with the increase in body weight during normal development.
GHGfrack: An Open-Source Model for Estimating Greenhouse Gas Emissions from Combustion of Fuel during Drilling and Hydraulic Fracturing.

PubMed

Vafi, Kourosh; Brandt, Adam

2016-07-19

This paper introduces GHGfrack, an open-source engineering-based model that estimates energy consumption and associated GHG emissions from drilling and hydraulic fracturing operations. We describe verification and calibration of GHGfrack against field data for energy and fuel consumption. We run GHGfrack using data from 6927 wells in Eagle Ford and 4431 wells in Bakken oil fields. The average estimated energy consumption in Eagle Ford wells using lateral hole diameters of 8 (3)/4 and 6 (1)/8 in. are 2.25 and 2.73 TJ/well, respectively. The average estimated energy consumption in Bakken wells using hole diameters of 6 in. for horizontal section is 2.16 TJ/well. We estimate average greenhouse gas (GHG) emissions of 419 and 510 tonne of equivalent CO2 per well (tonne of CO2 eq/well) for the two aforementioned assumed geometries in Eagle Ford, respectively, and 417 tonne of CO2 eq/well for the case of Bakken. These estimates are limited only to GHG emissions from combustion of diesel fuel to supply energy only for rotation of drill string, drilling mud circulation, and fracturing pumps. Sensitivity analysis of the model shows that the top three key variables in driving energy intensity in drilling are the lateral hole diameter, drill pipe internal diameter, and mud flow rate. In hydraulic fracturing, the top three are lateral casing diameter, fracturing fluid volume, and length of the lateral.
Echocolor Doppler morpho-functional study of the jugulo-subclavian confluence in chronic cerebro-spinal venous insufficiency and multiple sclerosis patients.

PubMed

Mandolesi, Sandro; d'Alessandro, Aldo; Desogus, Antonello Ignazio; Ciccone, Marco Matteo; Zito, Annapaola; Stammegna, Immacolata; Niglio, Tarcisio; Orsini, Augusto; Mandolesi, Dimitri; d'Alessandro, Alessandro; Revelli, Luca

2017-01-01

The aim of this work is to measure the mean diameter of the confluence jugulo- subclavian, the impact of different types of jugular confluences and the correlation between the types of confluences and the Valsalva maneuver (jugular reflux) in subjects with Chronic Cerebro-Spinal Venous Insufficiency (CCSVI) and Multiple Sclerosis. We investigated by Echo-Color-Doppler (ECD) 103 subjects (67 F 36M) of mean age 45 ± 12 years (a minimum of 22 to a maximum of 79 years, with a median of 44 and a modal value 42 years), mean EDSS of 4.7 and average disease duration of 12 years. The 103 right jugular veins investigated had an average diameter of 8.4 ± 2.4 mm (minimum 4.0, maximum 14.9 mm; median 7.9; modal value 7.6 mm). Three form types were found: 56 cylindrical, 29 conical and 18 funnel. Valsalva maneuver was positive in 30 patients. The 103 left jugular investigated had an average diameter of 8.9 ± 2.4 mm (minimum 2.8, maximum 14.4 mm; median of 8.8; modal value 8.7 mm). The form types were found: 42 cylindrical, 45 conical and 16 funnel. Valsalva maneuver was positive in 30 patients. The mean diameter of the jugular veins was 8.7 mm. Internal jugular veins with cylindrical morphology have a diameter smaller than other forms; this difference is statistically significant. The different morphology of the jugular vein confluence does not increase the possibility of a reflux because the positive Valsalva maneuvers are not statistically significant when compared to the various types. CCSVI, EchoColorDoppler Map, Jugulo-Subclavian Confluence Diameter.
Abhurite, a new tin hydroxychloride mineral, and a comparative study with a synthetic basic tin chloride.

USGS Publications Warehouse

Matzko, J.J.; Evans, H.T.; Mrose, M.E.; Aruscavage, P.

1985-01-01

Abhurite is a new mineral species found in blister-like protuberances on the surface of tin ingots submerged at a depth of 35 m in the Red Sea. It forms 1.5 mm diameter hexagonal plates bounded by the negative rhombohedron (0115); is colourless, transparent with opalescent lustre, white streak, hackly fracture, with no cleavage, and H.approx 2; D(calc) 4.34, D(meas) 4.29 g/cm3; epsilon approx 2.11, omega 2.06. Chemical analysis gave 73.4 wt.% Sn, 15.7 Cl, 11.0 0 and 0.4 H. leading to the formula Sn3O(OH)2Cl2. DTA shows release of H2O at 235oC and SnCl2 at 525oC. Indexed XRD powder data are tabulated; prominent lines 2.5313(100), 2.8915(70), 4.139(50), 3.404(50), 2.8175(50) A; a 10.0175(3), c 44.014(2) A; space group R3m, R3m or R32; Z = 21. Comparison is made with a hexagonal synthetic dimorph. The name refers to the geographical origin, an arm of the Red Sea known as Sharm Abhur.-L.T.T.
Comparison of the arithmetic and geometric means in estimating crown diameter and crown cross-sectional area

Treesearch

KaDonna Randolph

2010-01-01

The use of the geometric and arithmetic means for estimating tree crown diameter and crown cross-sectional area were examined for trees with crown width measurements taken at the widest point of the crown and perpendicular to the widest point of the crown. The average difference between the geometric and arithmetic mean crown diameters was less than 0.2 ft in absolute...
Effects of helium ion implantation on the surface morphology of tungsten at high temperature for the first wall armor and divertor plates of fusion reactors

NASA Astrophysics Data System (ADS)

Zenobia, Samuel J.

Three devices at the University of Wisconsin-Madison Inertial Electrostatic Confinement (UW IEC) laboratory were used to implant W and W alloys with helium ions at high temperatures. These devices were HOMER, HELIOS, and the Materials Irradiation Experiment (MITE-E). The research presented in this thesis will focus on the experiments carried out utilizing the MITE-E. Early UW work in HOMER and HELIOS on silicon carbide, carbon velvet, W-coated carbon velvet, fine-grain W, nano-grain W, W needles, and single- and polycrystalline W showed that these materials were not resistant to He+ implantation above ˜800 °C. Unalloyed W developed a "coral-like" surface morphology after He+ implantation, but appeared to be the most robust material investigated. The MITE-E used an ion gun technology to implant tungsten with 30 keV He+. Tungsten specimens were implanted at 900 °C to total average fluences of 6x1016 -- 6x1018 He +/cm2. Other specimens were implanted to a total average fluence of 5x1018 He+/cm2 at temperatures between 500 and 900 °C. Micrographs of the implanted W specimens revealed the development of three distinct surface morphologies. These morphologies are classified as "blistering", "pitting", and "orientated ridges". Preferential sputtering of the W by the energetic He+ appears to be responsible for pitting and orientated ridges which developed at high fluences (1019 He+/cm2) in the MITE-E. While the orientated ridges were the dominant morphology on the W surface above 700 °C, the pitting was prevalent below 700 °C. The blister morphology was observed at all of the examined temperatures at fluences ≥5x1017 He+/cm2 but disappeared above fluences of 1019 He+/cm 2. The "coral-like" surface morphology on W inherent to He + implantation experiments in HOMER and HELIOS developed from a combination of sources: multiangular ion incidence, ion energy spread (softening), and electron field emission from nano-scale surface features induced by He + implantation. The HOMER and HELIOS devices were found to be better suited for simulation of magnetic fusion environments with off-normal particle incidences, and the MITE-E was found to be more suited for simulating the normal particle incidence of inertial fusion environments.
A glass of red wine to keep vascular disease at bay, but what about pemphigus vulgaris?

PubMed

Caldarola, Giacomo; Feliciani, Claudio

2011-03-01

Pemphigus vulgaris is a rare autoimmune blistering disease, involving the skin and mucous epithelia, which is characterized by flaccid blisters and erosions. It is caused by the presence of autoantibodies directed against desmoglein, a glycoprotein that plays a critical role in cell-cell attachment. Upon a predisposing genetic background, different agents have been shown to act as triggers for the pathogenesis of pemphigus. The most evident association is with drug intake, while the role of diet is often underestimated. The aim of this article is to review the possible role of tannins, a group of phenolic metabolites that are widely distributed in almost all plant foods and beverages, particularly red wine, as a trigger for pemphigus vulgaris.
Nutritional support for children with epidermolysis bullosa.

PubMed

Haynes, Lesley

Epidermolysis bullosa (EB) comprises a rare group of genetically determined skin blistering disorders characterized by extreme fragility of the skin and mucous membranes, with recurrent blister formation. The cornerstones of management are control of infection, wound management, pain relief, promotion of optimal nutritional status and mobility, surgical intervention and provision of the best possible quality of life. There is currently no cure for EB and, throughout life, those with the more severe types are at risk of significant nutritional compromise which impacts negatively on health and overall quality of life. Nutritional support is an important facet of holistic care and the dietetic challenges can be considerable. This paper describes some of the issues involved in optimizing the nutritional status of children with this disorder.
Epidermolysis bullosa acquisita in a Great Dane.

PubMed

Hill, P B; Boyer, P; Lau, P; Rybnicek, J; Hargreaves, J; Olivry, T

2008-02-01

Autoimmune subepidermal blistering diseases in dogs were all classified as bullous pemphigoid until 1998. Since then, refinements in reagents and immunological techniques have allowed diseases which are histologically similar but which have a different molecular pathogenesis to be described. This report describes the first case of one such disease, epidermolysis bullosa acquisita, to be documented in the UK. The dog presented with a severe blistering and ulcerative disease affecting the oral cavity, pinnae and distal limbs. The diagnosis was confirmed by histopathology and direct and indirect immunofluorescent demonstration of immunoglobulin G reactivity to basement membrane antigens. Treatment with glucocorticoids, azathioprine, colchicine and an intravenous infusion of immunoglobulins resulted in complete resolution. The drugs were discontinued 12 months after the start of treatment and the dog remained in remission.
Low level light therapy and tattoos: A case report.

PubMed

Ingenito, Teresa

2016-10-01

Physical therapists (PTs) frequently provide neuromusculoskeletal treatment for patients who incidentally may have one or more tattoos. Low level light therapy (LLLT) is one of the modalities commonly used by physical therapists to decrease pain and facilitate healing. This case report describes a 22 year old man who was given LLLT to address his complaints of musculoskeletal pain. Blistering of the skin was documented over the LLLT application site, a black tattoo. The blisters, which formed after the LLLT treatment were most likely caused by the inadvertent and unexpected heating of the iron oxides and/or the metal salts in the tattoo's black pigment. PTs should exercise caution when applying LLLT in the presence of dark tattoos. Copyright © 2016 Elsevier Ltd. All rights reserved.
Carbon nanotube diameter selection by pretreatment of metal catalysts on surfaces

DOEpatents

Hauge, Robert H [Houston, TX; Xu, Ya-Qiong [Houston, TX; Shan, Hongwei [Houston, TX; Nicholas, Nolan Walker [South Charleston, WV; Kim, Myung Jong [Houston, TX; Schmidt, Howard K [Cypress, TX; Kittrell, W Carter [Houston, TX

2012-02-28

A new and useful nanotube growth substrate conditioning processes is herein disclosed that allows the growth of vertical arrays of carbon nanotubes where the average diameter of the nanotubes can be selected and/or controlled as compared to the prior art.
Biomass of singleleaf pinyon and Utah juniper

Treesearch

E. L. Miller; R. O. Meeuwig; J. D. Budy

1981-01-01

Biomass determinations in singleleaf pinyon (Pinus monophylla) - Utah juniper (Juniperus osteosperma) stands in Nevada indicate that stem diameter and average crown diameter are the tree measurements most highly correlated with ovendry weights. The equations and tables developed provide a means for estimating the total aboveground...
Spontaneous and controlled-diameter synthesis of single-walled and few-walled carbon nanotubes

NASA Astrophysics Data System (ADS)

Inoue, Shuhei; Lojindarat, Supanat; Kawamoto, Takahiro; Matsumura, Yukihiko; Charinpanitkul, Tawatchai

2018-05-01

In this study, we explored the spontaneous and controlled-diameter growth of carbon nanotubes. We evaluated the effects of catalyst density, reduction time, and a number of catalyst coating on the substrate (for multi-walled carbon nanotubes) on the diameter of single-walled carbon nanotubes and the number of layers in few-walled carbon nanotubes. Increasing the catalyst density and reduction time increased the diameters of the carbon nanotubes, with the average diameter increasing from 1.05 nm to 1.86 nm for single-walled carbon nanotubes. Finally, we succeeded in synthesizing a significant double-walled carbon nanotube population of 24%.
Half-peroneus-longus-tendon graft augmentation for unqualified hamstring tendon graft of anterior cruciate ligament reconstruction.

PubMed

Liu, Chung-Ting; Lu, Yung-Chang; Huang, Chang-Hung

2015-09-01

In some situations, harvested hamstring tendon grafts are not qualified for anterior cruciate ligament (ACL) reconstruction. This study aimed to present a reinforcing method with additional half peroneus longus tendon (half-PLT) graft augmentation. Eight cases underwent ACL reconstruction with unqualified hamstring tendon grafts (diameter <7 mm) and were salvaged by additional half-PLT graft augmentation. The pivot shift test and KT-1000 tests were performed 3 years after surgery. Functional evaluation of subjective International Knee Documentation Committee (IKDC) and Lysholm scores was also done. In addition, Foot and Ankle Disability Index (FADI) scores were used to evaluate the function of the ankle donor site. The diameter of unqualified four-strand hamstring tendon grafts was 6.2 mm on average (range, 6.0-6.5 mm). The average diameter of hamstring grafts with half-PLT augmentation was 9.6 mm (range, 9.5-10.0 mm). The pivot shift test was negative in all patients. No significant differences between normal and abnormal knees were found by KT-1000. The average IKDC score was 86.0 (range, 83 to 89), and the average Lysholm score was 84.4 (range, 80-90). The average FADI score for the donor sites of half-PLT was 135.8 (range, 134-136). Additional half-PLT can successfully and safely reinforce unqualified hamstring tendon grafts for ACL reconstruction.
Dermatitis, contact on the cheek (image)

MedlinePlus

... skin inflammation (dermatitis) on the cheek caused by contact with a substance that produced an allergic reaction (allergen). Contact dermatitis causes redness, itching, and small blisters (vesicles).
A novel strategy to translate the biomechanical rupture risk of abdominal aortic aneurysms to their equivalent diameter risk: method and retrospective validation.

PubMed

Gasser, T C; Nchimi, A; Swedenborg, J; Roy, J; Sakalihasan, N; Böckler, D; Hyhlik-Dürr, A

2014-03-01

To translate the individual abdominal aortic aneurysm (AAA) patient's biomechanical rupture risk profile to risk-equivalent diameters, and to retrospectively test their predictability in ruptured and non-ruptured aneurysms. Biomechanical parameters of ruptured and non-ruptured AAAs were retrospectively evaluated in a multicenter study. General patient data and high resolution computer tomography angiography (CTA) images from 203 non-ruptured and 40 ruptured aneurysmal infrarenal aortas. Three-dimensional AAA geometries were semi-automatically derived from CTA images. Finite element (FE) models were used to predict peak wall stress (PWS) and peak wall rupture index (PWRI) according to the individual anatomy, gender, blood pressure, intra-luminal thrombus (ILT) morphology, and relative aneurysm expansion. Average PWS diameter and PWRI diameter responses were evaluated, which allowed for the PWS equivalent and PWRI equivalent diameters for any individual aneurysm to be defined. PWS increased linearly and PWRI exponentially with respect to maximum AAA diameter. A size-adjusted analysis showed that PWS equivalent and PWRI equivalent diameters were increased by 7.5 mm (p = .013) and 14.0 mm (p < .001) in ruptured cases when compared to non-ruptured controls, respectively. In non-ruptured cases the PWRI equivalent diameters were increased by 13.2 mm (p < .001) in females when compared with males. Biomechanical parameters like PWS and PWRI allow for a highly individualized analysis by integrating factors that influence the risk of AAA rupture like geometry (degree of asymmetry, ILT morphology, etc.) and patient characteristics (gender, family history, blood pressure, etc.). PWRI and the reported annual risk of rupture increase similarly with the diameter. PWRI equivalent diameter expresses the PWRI through the diameter of the average AAA that has the same PWRI, i.e. is at the same biomechanical risk of rupture. Consequently, PWRI equivalent diameter facilitates a straightforward interpretation of biomechanical analysis and connects to diameter-based guidelines for AAA repair indication. PWRI equivalent diameter reflects an additional diagnostic parameter that may provide more accurate clinical data for AAA repair indication. Copyright © 2013 European Society for Vascular Surgery. Published by Elsevier Ltd. All rights reserved.
Effective separation technique for small diameter whiskers.

NASA Technical Reports Server (NTRS)

Westfall, L. J.

1972-01-01

Description of a technique for separating small-diameter whiskers from the as-grown matt by gently agitating the whisker matts in a solution of deionized or distilled water for six to eight hours. High-strength Al2O3 whiskers were effectively separated by this technique, comprising an average 48% of the original weight of the whisker matt. According to estimation, more than 90% of separated whiskers had diameters between 0.7 and 2.0 microns.
Effect of Climatic Factors on Hand, Foot, and Mouth Disease in South Korea, 2010-2013.

PubMed

Kim, Bryan Inho; Ki, Hyunok; Park, Sunhee; Cho, Eunhi; Chun, Byung Chul

2016-01-01

Hand, foot, and mouth disease (HFMD) causes characteristic blisters and sores mainly in infants and children, and has been monitored in South Korea through sentinel surveillance since 2009. We described the patterns of HFMD occurrence and analyzed the effect of climatic factors on national HFMD incidence. Weekly clinically diagnosed HFMD case rates (per 1,000 outpatients) in sentinel sites and weekly climatic factors, such as average temperature, relative humidity, duration of sunshine, precipitation, and wind speed from 2010 to 2013, were used in this study. A generalized additive model with smoothing splines and climatic variables with time lags of up to 2 weeks were considered in the modeling process. To account for long-term trends and seasonality, we controlled for each year and their corresponding weeks. The autocorrelation issue was also adjusted by using autocorrelation variables. At an average temperature below 18°C, the HFMD rate increased by 10.3% for every 1°C rise in average temperature (95% confidence interval (CI): 8.4, 12.3%). We also saw a 6.6% increase in HFMD rate (95% CI: 3.6, 9.7%) with every 1% increase in relative humidity under 65%, with a 1.5% decrease in HFMD rate observed (95% CI: 0.4, 2.7%) with each 1% humidity increase above 65%. Modeling results have shown that average temperature and relative humidity are related to HFMD rate. Additional research on the environmental risk factors of HFMD transmission is required to understand the underlying mechanism between climatic factors and HFMD incidence.

Interrater Agreement in the Radiologic Characterization of Ruptured Intracranial Aneurysms Based on Computed Tomography Angiography.

PubMed

Maldaner, Nicolai; Stienen, Martin N; Bijlenga, Philippe; Croci, Davide; Zumofen, Daniel W; Dalonzo, Donato; Marbacher, Serge; Maduri, Rodolfo; Daniel, Roy Thomas; Serra, Carlo; Esposito, Giuseppe; Neidert, Marian Christoph; Bozinov, Oliver; Regli, Luca; Burkhardt, Jan-Karl

2017-07-01

To determine interrater agreement in the initial radiologic characterization of ruptured intracranial aneurysms based on computed tomography angiography (CTA) with special emphasis on the rater's level of experience. One junior and one senior rater of 5 high-volume neurovascular tertiary centers evaluated anonymized CTA images of 30 consecutive patients with aneurysmal subarachnoid hemorrhage. Each rater described location, side, size, and morphology in a standardized manner. Interrater variability was analyzed using intraclass correlation and Fleiss' kappa analysis. There was a high level of agreement for location (κ = 0.76, 95% confidence interval [CI] 0.74-0.79), side (κ = 0.95, CI 0.91-0.99), maximum diameter (intraclass correlation coefficient [ICC] 0.81, CI 0.70-0.90), and dome (ICC 0.78, CI 0.66-0.88) of intracranial aneurysms. In contrast, a lower level of agreement was observed for aneurysms' neck diameter (ICC 0.39, CI 0.28-0.58), the presence of multiple aneurysms (κ = 0.35, CI 0.30-0.40), and aneurysm morphology (blister κ = 0.11, CI -0.05 to 0.07; fusiform κ = 0.54, CI 0.48-0.60; multilobular, κ = 0.39 CI 0.33-0.45). The interrater agreement in the senior rater group was greater than in the junior rater group. Interrater agreement confirms the benefit of CTA as initial diagnostic imaging in ruptured intracranial aneurysms but not for aneurysm morphology and presence of multiple aneurysms. A trend towards greater interrater agreement between more experienced raters was noticed. Copyright © 2017 Elsevier Inc. All rights reserved.
Transition of carbon nanostructures in heptane diffusion flames

NASA Astrophysics Data System (ADS)

Hu, Wei-Chieh; Hou, Shuhn-Shyurng; Lin, Ta-Hui

2017-02-01

The flame synthesis has high potential in industrial production of carbon nanostructure (CNS). Unfortunately, the complexity of combustion chemistry leads to less controlling of synthesized products. In order to improve the understanding of the relation between flames and CNSs synthesized within, experiments were conducted through heptane flames in a stagnation-point liquid-pool system. The operating parameters for the synthesis include oxygen supply, sampling position, and sampling time. Two kinds of nanostructures were observed, carbon nanotube (CNT) and carbon nano-onion (CNO). CNTs were synthesized in a weaker flame near extinction. CNOs were synthesized in a more sooty flame. The average diameter of CNTs formed at oxygen concentration of 15% was in the range of 20-30 nm. For oxygen concentration of 17%, the average diameter of CNTs ranged from 24 to 27 nm, while that of CNOs was around 28 nm. For oxygen concentration of 19%, the average diameter of CNOs produced at the sampling position 0.5 mm below the flame front was about 57 nm, while the average diameters of CNOs formed at the sampling positions 1-2.5 mm below the flame front were in the range of 20-25 nm. A transition from CNT to CNO was observed by variation of sampling position in a flame. We found that the morphology of CNS is directly affected by the presence of soot layer due to the carbonaceous environment and the growth mechanisms of CNT and CNO. The sampling time can alter the yield of CNSs depending on the temperature of sampling position, but the morphology of products is not affected.
Purification of 1.9-nm-diameter semiconducting single-wall carbon nanotubes by temperature-controlled gel-column chromatography and its application to thin-film transistor devices

NASA Astrophysics Data System (ADS)

Thendie, Boanerges; Omachi, Haruka; Hirotani, Jun; Ohno, Yutaka; Miyata, Yasumitsu; Shinohara, Hisanori

2017-06-01

Large-diameter semiconductor single-wall carbon nanotubes (s-SWCNTs) have superior mobility and conductivity to small-diameter s-SWCNTs. However, the purification of s-SWCNTs with diameters larger than 1.6 nm by gel filtration has been difficult owing to the low selectivity of the conventional purification method in these large-diameter regions. We report a combination of temperature-controlled gel filtration and the gradient elution technique that we developed to enrich a high-purity s-SWCNT with a diameter as large as 1.9 nm. The thin-film transistor (TFT) device using the 1.9-nm-diameter SWCNT shows an average channel mobility of 23.7 cm2 V-1 s-1, which is much higher than those of conventional SWCNT-TFTs with smaller-diameters of 1.5 and 1.4 nm.
Gene editing for skin diseases: designer nucleases as tools for gene therapy of skin fragility disorders.

PubMed

March, Oliver P; Reichelt, Julia; Koller, Ulrich

2018-04-01

What is the topic of this review? This review concerns current gene editing strategies for blistering skin diseases with respect to individual genetic constellations and distinct conditions. What advances does it highlight? Specificity and safety dominate the discussion of gene editing applications for gene therapy, where a number of tools are implemented. Recent developments in this rapidly progressing field pose further questions regarding which tool is best suited for each particular use. The current treatment of inherited blistering skin diseases, such as epidermolysis bullosa (EB), is largely restricted to wound care and pain management. More effective therapeutic strategies are urgently required, and targeting the genetic basis of these severe diseases is now within reach. Here, we describe current gene editing tools and their potential to correct gene function in monogenetic blistering skin diseases. We present the features of the most frequently used gene editing techniques, transcription activator-like effector nuclease (TALEN) and clustered regularly interspaced short palindromic repeats/CRISPR-associated protein 9 (CRISPR/Cas9), determining their preferential application for specific genetic conditions, including the type of mutational inheritance, the targeting site within the gene or the possibility to target the mutation specifically. Both tools have traits beneficial in specific situations. Promising developments in the field engender gene editing as a potentially powerful therapeutic option for future clinical applications. © 2017 The Authors. Experimental Physiology © 2017 The Physiological Society.
RNA-seq Analysis of Host and Viral Gene Expression Highlights Interaction between Varicella Zoster Virus and Keratinocyte Differentiation

PubMed Central

Singh, Manuraj; Kanda, Ravinder K.; Yee, Michael B.; Kellam, Paul; Hollinshead, Michael; Kinchington, Paul R.; O'Toole, Edel A.; Breuer, Judith

2014-01-01

Varicella zoster virus (VZV) is the etiological agent of chickenpox and shingles, diseases characterized by epidermal skin blistering. Using a calcium-induced keratinocyte differentiation model we investigated the interaction between epidermal differentiation and VZV infection. RNA-seq analysis showed that VZV infection has a profound effect on differentiating keratinocytes, altering the normal process of epidermal gene expression to generate a signature that resembles patterns of gene expression seen in both heritable and acquired skin-blistering disorders. Further investigation by real-time PCR, protein analysis and electron microscopy revealed that VZV specifically reduced expression of specific suprabasal cytokeratins and desmosomal proteins, leading to disruption of epidermal structure and function. These changes were accompanied by an upregulation of kallikreins and serine proteases. Taken together VZV infection promotes blistering and desquamation of the epidermis, both of which are necessary to the viral spread and pathogenesis. At the same time, analysis of the viral transcriptome provided evidence that VZV gene expression was significantly increased following calcium treatment of keratinocytes. Using reporter viruses and immunohistochemistry we confirmed that VZV gene and protein expression in skin is linked with cellular differentiation. These studies highlight the intimate host-pathogen interaction following VZV infection of skin and provide insight into the mechanisms by which VZV remodels the epidermal environment to promote its own replication and spread. PMID:24497829
Imaging sulfur mustard lesions in human epidermal tissues and keratinocytes by confocal and multiphoton microscopy

NASA Astrophysics Data System (ADS)

Werrlein, Robert; Madren-Whalley, Janna S.

2002-06-01

Topical exposure to sulfur mustard (HD), a known theat agent, produces persistent and debilitating cutaneous blisters. The blisters occur at the dermal-epidermal junction following a dose-dependent latent period of 8-24 h, however, the primary lesions causing vesication remain uncertain. Immunofluorescent images reveal that a 5-min exposure to 400 (mu) M HD disrupts molecules that are also disrupted by epidermolysis bullosa-type blistering diseases of the skin. Using keratinocyte cultures and fluorochomes conjugated to two different keratin-14 (K14) antibodies (clones CKB1 and LL002), results have shown a statistically significant (p<0.1) 1-h decrease of 29.2% in expression of the CKB1 epitope, a nearly complete loss of CKB1 expression within 2 h, and progressive cytoskeletal (K14) collapse without loss in expression of the LL002 epitope. With human epidermal tissues, multi-photon images of (alpha) 6 integrin and laminin 5 showed disruptive changes in the cell-surface organization and integrity of these adhesion molecules. At 1 H postexposure, analyses showed a statistically significant (p<0.1) decrease of 27.3% in (alpha) 6 integrin emissions, and a 32% decrease in laminin 5 volume. Multi-photon imaging indicates that molecules essential for epidermal-dermal attachment are early targets in the alkylating events leading to HD-induced vesication.
Structural Changes in the Vanadium Sample Surface Induced by Pulsed High-Temperature Deuterium Plasma and Deuterium Ion Fluxes

NASA Astrophysics Data System (ADS)

Borovitskaya, I. V.; Pimenov, V. N.; Gribkov, V. A.; Padukh, M.; Bondarenko, G. G.; Gaidar, A. I.; Paramonova, V. V.; Morozov, E. V.

2017-11-01

The structural changes in the vanadium sample surface are studied as functions of the conditions of irradiation by pulsed high-temperature deuterium plasma and deuterium ion fluxes in the Plasma Focus installation. It is found that processes of partial evaporation, melting, and crystallization of the surface layer of vanadium samples take place in the plasma flux power density range q = 108-1010 W/cm2 and the ion flux density range q = 1010-1012 W/cm2. The surface relief is wavelike. There are microcracks, gas-filled bubbles (blisters), and traces of fracture on the surface. The blisters are failed in the solid state. The character of blister fracture is similar to that observed during usual ion irradiation in accelerators. The samples irradiated at relatively low power density ( q = 107-108 W/cm2) demonstrate the ejection of microparticles (surface fragments) on the side facing plasma. This process is assumed to be due to the fact that the unloading wave formed in the sample-target volume reaches its irradiated surface. Under certain irradiation conditions (sample-anode distance, the number of plasma pulses), a block microstructure with block sizes of several tens of microns forms on the sample surfaces. This structure is likely to form via directional crack propagation upon cooling of a thin melted surface layer.
Effects of exotic species on Yellowstone's grizzly bears

USGS Publications Warehouse

Reinhart, Daniel P.; Haroldson, Mark A.; Mattson, D.J.; Gunther, Kerry A.

2001-01-01

Humans have affected grizzly bears (Ursus arctos horribilis) by direct mortality, competition for space and resources, and introduction of exotic species. Exotic organisms that have affected grizzly bears in the Greater Yellowstone Area include common dandelion (Taraxacum officinale), nonnative clovers (Trifolium spp.), domesticated livestock, bovine brucellosis (Brucella abortus), lake trout (Salvelinus namaycush), and white pine blister rust (Cronartium ribicola). Some bears consume substantial amounts of dandelion and clover. However, these exotic foods provide little digested energy compared to higher-quality bear foods. Domestic livestock are of greater energetic value, but use of this food by bears often leads to conflicts with humans and subsequent increases in bear mortality. Lake trout, blister rust, and brucellosis diminish grizzly bears foods. Lake trout prey on native cutthroat trout (Oncorhynchus clarkii) in Yellowstone Lake; white pine blister rust has the potential to destroy native whitebark pine (Pinus albicaulis) stands; and management response to bovine brucellosis, a disease found in the Yellowstone bison (Bison bison) and elk (Cervus elaphus), could reduce populations of these 2 species. Exotic species will likely cause more harm than good for Yellowstone grizzly bears. Managers have few options to mitigate or contain the impacts of exotics on Yellowstone's grizzly bears. Moreover, their potential negative impacts have only begun to unfold. Exotic species may lead to the loss of substantial highquality grizzly bear foods, including much of the bison, trout, and pine seeds that Yellowstone grizzly bears currently depend upon.
Gefitinib

MedlinePlus

... of medications called kinase inhibitors. It works by blocking the action of a certain naturally occurring substance ... blisters or peeling skin swelling of the eyes, face, lips, tongue, throat, hands, arms, feet, ankles or ...
Rashes

MedlinePlus

... rash is an area of irritated or swollen skin. Many rashes are itchy, red, painful, and irritated. ... also lead to blisters or patches of raw skin. Rashes are a symptom of many different medical ...
Growth and yield of Giant Sequoia

Treesearch

David J. Dulitz

1986-01-01

Very little information exists concerning growth and yield of giant sequoia (Sequoiadendron giganteum [Lindl.] Buchholz). For old-growth trees, diameter growth is the single factor adding increment since maximum height has been obtained. Diameter growth averages 0.04 inches per year in normal old-growth trees but will fluctuate with changes in the...
Error rate of automated calculation for wound surface area using a digital photography.

PubMed

Yang, S; Park, J; Lee, H; Lee, J B; Lee, B U; Oh, B H

2018-02-01

Although measuring would size using digital photography is a quick and simple method to evaluate the skin wound, the possible compatibility of it has not been fully validated. To investigate the error rate of our newly developed wound surface area calculation using digital photography. Using a smartphone and a digital single lens reflex (DSLR) camera, four photographs of various sized wounds (diameter: 0.5-3.5 cm) were taken from the facial skin model in company with color patches. The quantitative values of wound areas were automatically calculated. The relative error (RE) of this method with regard to wound sizes and types of camera was analyzed. RE of individual calculated area was from 0.0329% (DSLR, diameter 1.0 cm) to 23.7166% (smartphone, diameter 2.0 cm). In spite of the correction of lens curvature, smartphone has significantly higher error rate than DSLR camera (3.9431±2.9772 vs 8.1303±4.8236). However, in cases of wound diameter below than 3 cm, REs of average values of four photographs were below than 5%. In addition, there was no difference in the average value of wound area taken by smartphone and DSLR camera in those cases. For the follow-up of small skin defect (diameter: <3 cm), our newly developed automated wound area calculation method is able to be applied to the plenty of photographs, and the average values of them are a relatively useful index of wound healing with acceptable error rate. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.
Electrospun polyvinylpyrrolidone (PVP)/green tea extract composite nanofiber mats and their antioxidant activities

NASA Astrophysics Data System (ADS)

Pusporini, Pusporini; Edikresnha, Dhewa; Sriyanti, Ida; Suciati, Tri; Miftahul Munir, Muhammad; Khairurrijal, Khairurrijal

2018-05-01

Electrospinning was employed to make PVP (polyvinylpyrrolidone)/GTE (green tea extract) composite nanofiber mats. The electrospun PVP nanofiber mat as well as the PVP/GTE nanofiber mats were uniform. The average fiber diameter of PVP/GTE composite nanofiber mat decreased with increasing the GTE weight fraction (or decreasing the PVP weight fraction) in the PVP/GTE solution because the PVP/GTE solution concentration decreased. Then, the broad FTIR peak representing the stretching vibrations of O–H in hydroxyl groups of phenols and the stretching of N–H in amine groups of the GTE paste shifted to higher wavenumbers in the PVP/GTE composite nanofiber mats. These peak shifts implied that PVP and catechins of GTE in the PVP/GTE composite nanofiber mats had intermolecular interactions via hydrogen bonds between carbonyl groups of PVP and hydroxyl groups of catechins in GTE. Lastly, the antioxidant activity of the PVP/GTE composite nanofiber mat increased with reducing the average fiber diameter because the amount of catechins in the composite nanofiber mat increased with the increase of surface area due to the reduction of the average fiber diameter.
Comparison between Single-Walled CNT, Multi-Walled CNT, and Carbon Nanotube-Fiber Pyrograf III

NASA Astrophysics Data System (ADS)

Mousa, Marwan S.

2018-02-01

Single-Walled CNT (SWCNTs), Multi-walled Carbon Nanotubes (MWCNTs), and Carbon Nanotube-Fibers Pyrograf III PR-1 (CNTFs) were deposited by chemical vapor deposition under vacuum pressure value of (10-7mbar). Their structures were investigated by field emission microscopy. Carbon Nano-Fibers Pyrograf III PR-1 showed an average fiber diameter within the range of 100-200 nm and a length of (30-100) μm. Single-walled Carbon Nanotubes were produced by high-pressure Carbon Monoxide process with an average diameter ranging between (1-4) nm and a length of (1-3) μm. Thin Multiwall Carbon Nanotube of carbon purity (90%) showed an average diameter tube (9.5 nm) with a high-aspect-ratio (>150). The research work reported here includes the field electron emission current-voltage (I-V) characteristics and presented as Fowler-Nordheim (FN) plots and the spatial emission current distributions (electron emission images) obtained and analyzed in terms of electron source features. For the three types of emitters, a single spot pattern for the electron spatial; distributions were observed, with emission current fluctuations in some voltage region.
Normal Cerebellar Growth by Using Three-dimensional US in the Preterm Infant from Birth to Term-corrected Age.

PubMed

Benavente-Fernández, Isabel; Rodríguez-Zafra, Enrique; León-Martínez, Jesús; Jiménez-Gómez, Gema; Ruiz-González, Estefanía; Fernández-Colina, Rosalía Campuzano; Lechuga-Sancho, Alfonso M; Lubián-López, Simón P

2018-04-03

Purpose To establish cross-sectional and longitudinal reference values for cerebellar size in preterm infants with normal neuroimaging findings and normal 2-year neurodevelopmental outcome by using cranial ultrasonography (US). Materials and Methods This prospective study consecutively enrolled preterm infants admitted to a neonatal intensive care unit from June 2011 to June 2014 with a birth weight of less than or equal to 1500 g and/or gestational age (GA) of less than or equal to 32 weeks. They underwent weekly cranial US from birth to term-equivalent age and magnetic resonance (MR) imaging at term-equivalent age. The infants underwent neurodevelopmental assessments at age 2 years with Bayley Scales of Infant and Toddler Development, 3rd edition (BSID-III). Patients with adverse outcomes (death or abnormal neuroimaging findings and/or BSID-III score of <85) were excluded. The following measurements were performed: vermis height, craniocaudal diameter, superior width, inferior width, vermis area, and transcerebellar diameter. Statistical analyses were conducted by using multilevel analyses. Results A total of 137 infants with a mean GA at birth of 29.4 weeks (range, 25-32 weeks) were included. Transcerebellar diameter increased by 1.04 mm per week on average; vermis height and craniocaudal diameter increased by 0.55 mm and 0.59 mm, respectively. Superior vermian width increased by an average of 0.45 mm, whereas inferior vermian width increased by an average of 0.51 mm per week. Vermis area was found to increase by 0.22 cm 2 per week on average. The sex effect was significant (female lower than male) for vermis height (P < .05), craniocaudal diameter (P < .05), inferior vermian width (P <. 05), and vermis area (P <. 05). Conclusion Cross-sectional and longitudinal reference values were established for cerebellar growth in preterm infants, which may be included in routine cranial US. © RSNA, 2018 Online supplemental material is available for this article.
Production of polycaprolactone nanoparticles with low polydispersity index in a tubular recirculating system by using a multifactorial design of experiments

NASA Astrophysics Data System (ADS)

Colmenares Roldán, Gabriel Jaime; Agudelo Gomez, Liliana María; Carlos Cornelio, Jesús Antonio; Rodriguez, Luis Fernando; Pinal, Rodolfo; Hoyos Palacio, Lina Marcela

2018-03-01

Encapsulation and controlled release of substances using polymeric nanoparticles require that these have a high reproducibility, homogeneity, and control over their properties (diameter and polydispersity), especially when they are to be used in medical, pharmaceutical, or nutritional applications among others. In conventional production systems, it is tough to ensure these characteristics; hence, the cost increases when we try to control these properties. This paper shows a comparison between a recirculating system and the standard nanoprecipitation technique for producing polymeric nanoparticles. In previous investigations, we evaluate the effect of recirculating flow and the ratio between the organic and aqueous phase. For this paper, we evaluated the effect of polymer and surfactant concentrations using a multifactorial design of experiments on the recirculating system and on the standard nanoprecipitation system. The response of the design was the average diameter of the nanoparticles and polydispersity index. Finally, we found that the polymer and surfactant concentrations could change the average diameter and polydispersity index of the nanoparticles obtained. On the other hand, it was found that the effect of the polymer concentration was stronger than the surfactant concentration to reduce the average diameter of the nanoparticles. The results of the present study show that the proposed recirculation system presents a high potential to produce polymer nanoparticles with good morphological characteristics, particle size distributions in the nano range, and with a low polydispersity. The average mean size of nanoparticles of polycaprolactone for the design using the recirculating system was of 61 to 140 nm and the values of polydispersity index PDI for this design were between 0.097 and 0.22, while for the design using the standard nanoprecipitation technique, the obtained diameters were 74 to 176 nm and the polydispersity was between 0.26 and 0.41.
Red-shouldered hawk nesting habitat preference in south Texas

USGS Publications Warehouse

Strobel, Bradley N.; Boal, Clint W.

2010-01-01

We examined nesting habitat preference by red-shouldered hawks Buteo lineatus using conditional logistic regression on characteristics measured at 27 occupied nest sites and 68 unused sites in 2005–2009 in south Texas. We measured vegetation characteristics of individual trees (nest trees and unused trees) and corresponding 0.04-ha plots. We evaluated the importance of tree and plot characteristics to nesting habitat selection by comparing a priori tree-specific and plot-specific models using Akaike's information criterion. Models with only plot variables carried 14% more weight than models with only center tree variables. The model-averaged odds ratios indicated red-shouldered hawks selected to nest in taller trees and in areas with higher average diameter at breast height than randomly available within the forest stand. Relative to randomly selected areas, each 1-m increase in nest tree height and 1-cm increase in the plot average diameter at breast height increased the probability of selection by 85% and 10%, respectively. Our results indicate that red-shouldered hawks select nesting habitat based on vegetation characteristics of individual trees as well as the 0.04-ha area surrounding the tree. Our results indicate forest management practices resulting in tall forest stands with large average diameter at breast height would benefit red-shouldered hawks in south Texas.
Stone Attenuation Values Measured by Average Hounsfield Units and Stone Volume as Predictors of Total Laser Energy Required During Ureteroscopic Lithotripsy Using Holmium:Yttrium-Aluminum-Garnet Lasers.

PubMed

Ofude, Mitsuo; Shima, Takashi; Yotsuyanagi, Satoshi; Ikeda, Daisuke

2017-04-01

To evaluate the predictors of the total laser energy (TLE) required during ureteroscopic lithotripsy (URS) using the holmium:yttrium-aluminum-garnet (Ho:YAG) laser for a single ureteral stone. We retrospectively analyzed the data of 93 URS procedures performed for a single ureteral stone in our institution from November 2011 to September 2015. We evaluated the association between TLE and preoperative clinical data, such as age, sex, body mass index, and noncontrast computed tomographic findings, including stone laterality, location, maximum diameter, volume, stone attenuation values measured using average Hounsfield units (HUs), and presence of secondary signs (severe hydronephrosis, tissue rim sign, and perinephric stranding). The mean maximum stone diameter, volume, and average HUs were 9.2 ± 3.8 mm, 283.2 ± 341.4 mm 3 , and 863 ± 297, respectively. The mean TLE and operative time were 2.93 ± 3.27 kJ and 59.1 ± 28.1 minutes, respectively. Maximum stone diameter, volume, average HUs, severe hydronephrosis, and tissue rim sign were significantly correlated with TLE (Spearman's rho analysis). Stepwise multiple linear regression analysis defining stone volume, average HUs, severe hydronephrosis, and tissue rim sign as explanatory variables showed that stone volume and average HUs were significant predictors of TLE (standardized coefficients of 0.565 and 0.320, respectively; adjusted R 2 = 0.55, F = 54.7, P <.001). Stone attenuation values measured by average HUs and stone volume were strong predictors of TLE during URS using Ho:YAG laser procedures. Copyright © 2016 Elsevier Inc. All rights reserved.
Pemphigus

MedlinePlus

... risk for pemphigus. Pemphigoid is also an autoimmune skin disease. It leads to deep blisters that do not break easily. Pemphigoid is most common in older adults and may be fatal for older, sick patients. ...
Jellyfish stings

MedlinePlus

... include: Lion's mane ( Cyanea capillata ). Portuguese man-of-war ( Physalia physalis in the Atlantic and Physalia utriculus ... Skin burning and blistering (severe) PORTUGUESE MAN-OF-WAR Abdominal pain Changes in pulse Chest pain Chills ...

Anthrax: Symptoms

MedlinePlus

... and cause severe illness and even death. Cutaneous anthrax symptoms can include: A group of small blisters ... on the face, neck, arms, or hands Inhalation anthrax symptoms can include: Fever and chills Chest Discomfort ...
A Case of Ruptured Blood Blister-like Aneurysm Treated with Pipeline Embolization Device: Clinical Significance of Fetal-type Posterior Communicating Artery.

PubMed

Park, Ki-Su; Kang, Dong-Hun; Son, Won-Soo; Park, Jaechan; Kim, Young-Sun; Kim, Byung Moon

2017-03-01

Blood-blister like aneurysms (BBAs) are challenging lesions because of their wide fragile neck. Flow-diverting stents (FDSs), such as the Pipeline Embolization Device (PED), have been applied to treat BBAs less amenable to more established techniques of treatment. However, the use of FDSs, including the PED, in acute subarachnoid hemorrhage (SAH) still remains controversial. We report a case of aneurysm regrowth following PED application for a ruptured BBA that overlapped the origin of the dominant posterior communicating artery (PCoA), which was successfully treated after coil trapping of the origin of the fetal-type PCoA. And, we discuss the clinical significance of the fetal-type PCoA communicating with a BBA in terms of PED failure.
Emergency management of chemical weapons injuries.

PubMed

Anderson, Peter D

2012-02-01

The potential for chemical weapons to be used in terrorism is a real possibility. Classes of chemical weapons include nerve agents, vesicants (blister agents), choking agents, incapacitating agents, riot control agents, blood agents, and toxic industrial chemicals. The nerve agents work by blocking the actions of acetylcholinesterase leading to a cholinergic syndrome. Nerve agents include sarin, tabun, VX, cyclosarin, and soman. The vesicants include sulfur mustard and lewisite. The vesicants produce blisters and also damage the upper airways. Choking agents include phosgene and chlorine gas. Choking agents cause pulmonary edema. Incapacitating agents include fentanyl and its derivatives and adamsite. Riot control agents include Mace and pepper spray. Blood agents include cyanide. The mechanism of toxicity for cyanide is blocking oxidative phosphorylation. Toxic industrial chemicals include agents such as formaldehyde, hydrofluoric acid, and ammonia.
Epidermolysis Bullosa Acquisita: Autoimmunity to Anchoring Fibril Collagen

PubMed Central

Chen, Mei; Kim, Gene H.; Prakash, Lori; Woodley, David T.

2012-01-01

Epidermolysis bullosa acquisita (EBA) is a rare and acquired autoimmune subepidermal bullous disease of the skin and mucosa. EBA includes various distinct clinical manifestations resembling Bullous Pemphigus, Brunsting-Perry pemphigoid, or cicatricial pemphigoid. These patients have autoantibodies against type VII collagen, an integral component of anchoring fibrils, which are responsible for attaching the dermis to the epidermis. Destruction or perturbation of the normally functioning anchoring fibrils clinically results in skin fragility, blisters, erosions, scars, milia and nail loss, all features reminiscent of genetic dystrophic epidermolysis bullosa. These anti-type VII collagen antibodies are “pathogenic” because when injected into a mouse, the mouse develops an EBA-like blistering disease. Currently treatment is often unsatisfactory, however some success has been achieved with colchichine, dapsone, photopheresis, plasmaphresis, infliximab, rituximab and IVIG. PMID:21955050
A Case of Ruptured Blood Blister-like Aneurysm Treated with Pipeline Embolization Device: Clinical Significance of Fetal-type Posterior Communicating Artery

PubMed Central

Park, Ki-Su; Son, Won-Soo; Park, Jaechan; Kim, Young-Sun; Kim, Byung Moon

2017-01-01

Blood-blister like aneurysms (BBAs) are challenging lesions because of their wide fragile neck. Flow-diverting stents (FDSs), such as the Pipeline Embolization Device (PED), have been applied to treat BBAs less amenable to more established techniques of treatment. However, the use of FDSs, including the PED, in acute subarachnoid hemorrhage (SAH) still remains controversial. We report a case of aneurysm regrowth following PED application for a ruptured BBA that overlapped the origin of the dominant posterior communicating artery (PCoA), which was successfully treated after coil trapping of the origin of the fetal-type PCoA. And, we discuss the clinical significance of the fetal-type PCoA communicating with a BBA in terms of PED failure. PMID:28316868
Stochastic theory of fatigue corrosion

NASA Astrophysics Data System (ADS)

Hu, Haiyun

1999-10-01

A stochastic theory of corrosion has been constructed. The stochastic equations are described giving the transportation corrosion rate and fluctuation corrosion coefficient. In addition the pit diameter distribution function, the average pit diameter and the most probable pit diameter including other related empirical formula have been derived. In order to clarify the effect of stress range on the initiation and growth behaviour of pitting corrosion, round smooth specimen were tested under cyclic loading in 3.5% NaCl solution.
Acoustic fill factors for a 120 inch diameter fairing

NASA Technical Reports Server (NTRS)

Lee, Y. Albert

1992-01-01

Data from the acoustic test of a 120-inch diameter payload fairing were collected and an analysis of acoustic fill factors were performed. Correction factors for obtaining a weighted spatial average of the interior sound pressure level (SPL) were derived based on this database and a normalized 200-inch diameter fairing database. The weighted fill factors were determined and compared with statistical energy analysis (VAPEPS code) derived fill factors. The comparison is found to be reasonable.
Formation of small gold clusters in solution by laser excitation of interband transition

NASA Astrophysics Data System (ADS)

Mafuné, Fumitaka; Kondow, Tamotsu

2003-04-01

Gold nanoparticles with ˜10 nm in average diameter were prepared by laser ablation of a gold metal plate in an aqueous solution of sodium dodecyl sulfate (SDS) and were fragmented by excitation of an interband transition of gold nanoparticles under irradiation of an intense 355-nm pulsed laser. Fragmentation dynamics was investigated by comparing the fragmentation by excitation of a surface plasmon band of gold nanoparticles by a 532-nm laser. It is found that gold nanoparticles with 1.5-nm average diameter are produced together with small gold clusters by properly optimizing the surfactant concentration.
Poison Ivy Dermatitis

MedlinePlus

... rashes need treatment to ease the misery and disability they cause. The very first time this rash ... the compresses and apply only the cream. Cream applied before the blisters and swelling go down are ...
Stevens-Johnson Syndrome

MedlinePlus

... after blisters form If you have Stevens-Johnson syndrome, several days before the rash develops you may experience: Fever Sore mouth and throat Fatigue Cough Burning eyes When to see a doctor Stevens-Johnson ...
Hydrofluoric acid poisoning

MedlinePlus

... your skin or eyes, you may have: Blisters Burns Pain Vision loss Hydrofluoric acid poisoning can have ... urine tests Camera down the throat to see burns in the esophagus and the stomach (endoscopy) Fluids ...
Does packaging with a calendar feature improve adherence to self-administered medication for long-term use? A systematic review.

PubMed

Zedler, Barbara K; Kakad, Priyanka; Colilla, Susan; Murrelle, Lenn; Shah, Nirav R

2011-01-01

The therapeutic benefit of self-administered medications for long-term use is limited by an average 50% nonadherence rate. Patient forgetfulness is a common factor in unintentional nonadherence. Unit-of-use packaging that incorporates a simple day-and-date feature (calendar packaging) is designed to improve adherence by prompting patients to maintain the prescribed dosing schedule. To review systematically, in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement, randomized controlled trial evidence of the adherence benefits and harms of calendar blister packaging (CBP) and calendar pill organizers (CPO) for self-administered, long-term medication use. Data sources included the MEDLINE and Web of Science and Cochrane Library databases from their inception to September 2010 and communication with researchers in the field. Key search terms included blister-calendar pack, blister pack, drug packaging, medication adherence, medication compliance, medication compliance devices, medication containers, medication organizers, multicompartment compliance aid, persistence, pill-box organizers, prescription refill, randomized controlled trials, and refill compliance. Selected studies had an English-language title; a randomized controlled design; medication packaged in CBP or CPO; a requirement of solid, oral medication self-administered daily for longer than 1 month in community-dwelling adults; and at least 1 quantitative outcome measure of adherence. Two reviewers extracted data independently on study design, sample size, type of intervention and control, and outcomes. Ten trials with a total of 1045 subjects met the inclusion criteria, and 9 also examined clinical outcomes (seizures, blood pressure, psychiatric symptoms) or health care resource utilization. Substantial heterogeneity among trials precluded meta-analysis. In 3 studies, calendar packaging was part of a multicomponent adherence intervention. Six of 10 trials reported higher adherence, but it was associated with clinically significant improvement in only 1 study: 50% decreased seizure frequency with a CPO-based, multicomponent intervention. No study reported sufficient information to examine conclusively potential harms related to calendar packaging. All trials had significant methodological limitations, such as inadequate randomization or blinding, or reported insufficient information regarding enrolled subjects and attrition, which resulted in a moderate-to-high risk of bias and, in 2 studies, unevaluable outcome data. Trials were generally short and sample sizes small, with heterogeneous adherence outcome measures. Calendar packaging, especially in combination with education and reminder strategies, may improve medication adherence. Methodological limitations preclude definitive conclusions about the effect size of adherence and clinical benefits or harms associated with CBP and CPO. High-quality trials of adequate size and duration are needed to assess the clinical effectiveness of such interventions. Copyright © 2011 Elsevier HS Journals, Inc. All rights reserved.
Diameters of the cavo-sinus-tricuspid area in relation to type I atrial flutter.

PubMed

Kozłowski, Dariusz; Hreczecha, Jolanta; Skwarek, Magdalena; Piwko, Grzegorz; Kosiński, Adam; Gawrysiak, Marcin; Grzybiak, Marek

2003-05-01

Cardiac arrhythmias have troubled patients and fascinated physicians for centuries. The twentieth century was an era of progress, when the mechanism of cardiac disorders became more commonly recognised. Arrhythmias may be due to abnormalities of automaticity, to abnormalities of conduction, or to a combination of both. In order for re-entry to occur, an area of slowing conduction combined with unidirectional block must be present. Much investigation has centred on the underlying re-entry mechanisms of atrial flutter. In the light of these facts, it would seem that a close acquaintance with the detailed topography of the vena cava orifice (cavo), coronary sinus orifice (sinus) and the attachment of the septal leaflet of the tricuspid valve (tricupid) area could be of great interest, especially for invasive cardiologists. The research was conducted carried out on material consisting of 41 hearts of humans of both sexes from the age of 12 to 80 (6 female, 35 male). Classical macroscopic methods of anatomical evaluation were used. The following measurements were made: the shortest distance between the Eustachian valve and the attachment of the tricuspid valve on the left margin of the coronary sinus orifice (diameter 1), the distance between the attachment of the tricuspid valve and the inferior margin of the sinus orifice (diameter 2), the distance between the Eustachian valve and the attachment of the tricuspid valve on the right margin of the coronary sinus orifice (diameter 3), the distance between the inferior margin of the vena cava inferior and the attachment of the tricuspid valve (diameter 4) and, finally, the diameter between the attachment of the septal cusp of the tricuspid valve and the extemal border of the vena cava inferior (diameter 5). No correlation was found between the age and sex of the three groups of the material. The dimensions of the structure examined were similar in the three groups of hearts. In young adult hearts all the diameters measured ranged from 4 to 47 mm. The average diameters were, respectively: 15.02 mm (diameter 1), 8.97 mm (diameter 2), 17.27 mm (diameter 3), 26.87 mm (diameter 4), 36.42 mm (diameter 5). In the mature adult hearts all the diameters measured ranged from 8 to 45 mm; 18.19 mm (diameter 1), 10.54 mm (diameter 2), 19.95 mm (diameter 3), 28.90 mm (diameter 4), 39.63 mm (diameter 5). In the older adults hearts all the diameters measured ranged from 4 to 47 mm. The average diameters were, respectively: 15.65 mm (diameter 1), 8.70 mm (diameter 2), 7.25 mm (diameter 3), 26.80 mm (diameter 4), 35.85 mm (diameter 5). On the basis of our study we were able to conclude that the diameters of the cavo-sinus-tricuspid area were constant and did not differ significantly within the three (young, mature, old) adult groups examined.
Stress changes ahead of an advancing tunnel

USGS Publications Warehouse

Abel, J.F.; Lee, F.T.

1973-01-01

Instrumentation placed ahead of three model tunnels in the laboratory and ahead of a crosscut driven in a metamorphic rock mass detected stress changes several tunnel diameters ahead of the tunnel face. Stress changes were detected 4 diameters ahead of a model tunnel drilled into nearly elastic acrylic, 2??50 diameters ahead of a model tunnel drilled into concrete, and 2 diameters ahead of a model tunnel drilled into Silver Plume Granite. Stress changes were detected 7??50 diameters ahead of a crosscut driven in jointed, closely foliated gneisses and gneissic granites in an experimental mine at Idaho Springs, Colorado. These results contrast markedly with a theoretical elastic estimate of the onset of detectable stress changes at 1 tunnel diameter ahead of the tunnel face. A small compressive stress concentration was detected 2 diameters ahead of the model tunnel in acrylic, 1.25 diameters ahead of the model tunnel in concrete, and 1 diameter ahead of the model tunnel in granite. A similar stress peak was detected about 6 diameters ahead of the crosscut. No such stress peak is predicted from elastic theory. The 3-dimensional in situ stress determined in the field demonstrate that geologic structure controls stress orientations in the metamorphic rock mass. Two of the computed principal stresses are parallel to the foliation and the other principal stress is normal to it. The principal stress orientations vary approximately as the foliation attitude varies. The average horizontal stress components and the average vertical stress component are three times and twice as large, respectively, as those predicted from the overburden load. An understanding of the measured stress field appears to require the application of either tectonic or residual stress components, or both. Laboratory studies indicate the presence of proportionately large residual stresses. Mining may have triggered the release of strain energy, which is controlled by geologic structure. ?? 1973.
Morphological control of three-dimensional carbon nanotube anode for high-capacity lithium-ion battery

NASA Astrophysics Data System (ADS)

Kang, Chiwon; Lee, Hoo-Jeong

2018-05-01

In this paper, we report the results of modulating the processing conditions (mainly, temperature) of a two-step method consisting of sputtering deposition of a Ni catalytic layer and chemical vapor deposition (CVD) of carbon nanotubes (CNTs) on a three-dimensional (3D)-structured Cu mesh to control the morphology of CNTs for advanced Li-ion battery (LIB) applications. We disclosed that CNT growth at a low temperature (700 °C) produced small-diameter CNTs (CNT_S) with an average diameter of ∼20 nm, while that at a high temperature (750 °C) produced large-diameter CNTs (CNT_L) with an average diameter of 200–300 nm. The high-resolution transmission electron microscopy (HR-TEM) and Raman analyses manifested poorly crystalline CNTs for both samples. CNTS showed a specific capacity of 476 mAh g‑1, which is ∼176% superior to that of CNTL (271 mAh g‑1) and ∼128% higher than the theoretical capacity of the state-of-the-art graphites and recently reported nanostructured carbon-based anode materials.
Influence of hydrothermal synthesis parameters on the properties of hydroxyapatite nanoparticles.

PubMed

Kuśnieruk, Sylwia; Wojnarowicz, Jacek; Chodara, Agnieszka; Chudoba, Tadeusz; Gierlotka, Stanislaw; Lojkowski, Witold

2016-01-01

Hydroxyapatite (HAp) nanoparticles of tunable diameter were obtained by the precipitation method at room temperature and by microwave hydrothermal synthesis (MHS). The following parameters of the obtained nanostructured HAp were determined: pycnometric density, specific surface area, phase purity, lattice parameters, particle size, particle size distribution, water content, and structure. HAp nanoparticle morphology and structure were determined using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). X-ray diffraction measurements confirmed crystalline HAp was synthesized, which was pure in terms of phase. It was shown that by changing the synthesis parameters, the diameter of HAp nanoparticles could be controlled. The average diameter of the HAp nanoparticles was determined by Scherrer's equation via the Nanopowder XRD Processor Demo web application, which interprets the results of specific surface area and TEM measurements using the dark-field technique. The obtained nanoparticles with average particle diameter ranging from 8-39 nm were characterized by having homogeneous morphology with a needle shape and a narrow particle size distribution. Strong similarities were found when comparing the properties of some types of nanostructured hydroxyapatite with natural occurring apatite found in animal bones and teeth.
Babies and heat rashes

MedlinePlus

... occurs in babies when the pores of the sweat glands become blocked. This happens most often when ... weather is hot or humid. As your infant sweats, little red bumps, and possibly tiny blisters, form ...
Load deflection characteristics and force level of nickel titanium initial archwires.

PubMed

Lombardo, Luca; Marafioti, Matteo; Stefanoni, Filippo; Mollica, Francesco; Siciliani, Giuseppe

2012-05-01

To investigate and compare the characteristics of commonly used types of traditional and heat-activated initial archwire by plotting their load/deflection graphs and quantifying three suitable parameters describing the discharge plateau phase. Forty-eight archwires (22 nickel titanium [NiTi] and 26 heat-activated) of cross-sectional diameter ranging from 0.010 to 0.016 inch were obtained from seven different manufacturers. A modified three-point wire-bending test was performed on three analogous samples of each type of archwire at a constant temperature (37.0°C). For each resulting load/deflection curve, the plateau section was isolated, along with the mean value of the average plateau force, the plateau length, and the plateau slope for each type of wire obtained. Statistically significant differences were found between almost all wires for the three parameters considered. Statistically significant differences were also found between traditional and heat-activated archwires, the latter of which generated longer plateaus and lighter average forces. The increase in average force seen with increasing diameter tended to be rather stable, although some differences were noted between traditional and heat-activated wires. Although great variation was seen in the plateau behavior, heat-activated versions appear to generate lighter forces over greater deflection plateaus. On average, the increase in plateau force was roughly 50% when the diameter was increased by 0.002 inch (from 0.012 to 0.014 and from 0.014 to 0.016 inch) and about 150% when the diameter was increased by 0.004 inch (from 0.012 to 0.016), with differences between traditional and heat-activated wires noted in this case.
Morphology of Lonar Crater, India: Comparisons and implications

USGS Publications Warehouse

Fudali, R.F.; Milton, D.J.; Fredriksson, K.; Dube, A.

1980-01-01

Lonar Crater is a young meteorite impact crater emplaced in Deccan basalt. Data from 5 drillholes, a gravity network, and field mapping are used to reconstruct its original dimensions, delineate the nature of the pre-impact target rocks, and interpret the emplacement mode of the ejecta. Our estimates of the pre-erosion dimensions are: average diameter of 1710 m; average rim height of 40 m (30-35 m of rim rock uplift, 5-10 m of ejected debris); depth of 230-245 m (from rim crest to crater floor). The crater's circularity index is 0.9 and is unlikely to have been lower in the past. There are minor irregularities in the original crater floor (present sediment-breccia boundary) possibly due to incipient rebound effects. A continuous ejecta blanket extends an average of 1410 m beyond the pre-erosion rim crest. In general, 'fresh' terrestrial craters, less than 10 km in diameter, have smaller depth/diameter and larger rim height/diameter ratios than their lunar counterparts. Both ratios are intermediate for Mercurian craters, suggesting that crater shape is gravity dependent, all else being equal. Lonar demonstrates that all else is not always equal. Its depth/diameter ratio is normal but, because of less rim rock uplift, its rim height/diameter ratio is much smaller than both 'fresh' terrestrial and lunar impact craters. The target rock column at Lonar consists of one or more layers of weathered, soft basalt capped by fresh, dense flows. Plastic deformation and/or compaction of this lower, incompetent material probably absorbed much of the energy normally available in the cratering process for rim rock uplift. A variety of features within the ejecta blanket and the immediately underlying substrate, plus the broad extent of the blanket boundaries, suggest that a fluidized debris surge was the dominant mechanism of ejecta transportation and deposition at Lonar. In these aspects, Lonar should be a good analog for the 'fluidized craters' of Mars. ?? 1980 D. Reidel Publishing Co.
Airflow and temperature distribution inside the maxillary sinus: a computational fluid dynamics simulation.

PubMed

Zang, Hongrui; Liu, Yingxi; Han, Demin; Zhang, Luo; Wang, Tong; Sun, Xiuzhen; Li, Lifeng

2012-06-01

The airflow velocity and flux in maxillary sinuses were much lower than those in the nasal cavity, and the temperature in maxillary sinuses was much higher than the temperature in the middle meatus. With the increase of maximum diameter of the ostium, the above indices changed little. The purpose of the paper was to investigate, first, the flow and temperature distribution inside normal maxillary sinus in inspiration, and second, flow and temperature alteration with the increase of maximum ostium diameter. Three-dimensional models with nasal cavities and bilateral maxillary sinuses were constructed for computational fluid dynamics analysis. Virtual surgeries were implemented for the maxillary ostium, the maximum diameters of which were 8, 10, 12, and 15 mm, respectively. The finite volume method was used for numerical simulation. The indices of velocity, pressure, vector, and temperature were processed and compared between models. The airflow velocity in maxillary sinuses (average velocity 0.062 m/s) was much lower than that in the middle meatus (average velocity 3.26 m/s). With the increase of ostium diameter, airflow characteristics distributed in the maxillary sinuses changed little. The normal temperature in the maxillary sinus remained almost constant at 34°C and changed little with the increase of ostium diameter.

Definition of the Spatial Resolution of X-Ray Microanalysis in Thin Foils

NASA Technical Reports Server (NTRS)

Williams, D. B.; Michael, J. R.; Goldstein, J. I.; Romig, A. D., Jr.

1992-01-01

The spatial resolution of X-ray microanalysis in thin foils is defined in terms of the incident electron beam diameter and the average beam broadening. The beam diameter is defined as the full width tenth maximum of a Gaussian intensity distribution. The spatial resolution is calculated by a convolution of the beam diameter and the average beam broadening. This definition of the spatial resolution can be related simply to experimental measurements of composition profiles across interphase interfaces. Monte Carlo calculations using a high-speed parallel supercomputer show good agreement with this definition of the spatial resolution and calculations based on this definition. The agreement is good over a range of specimen thicknesses and atomic number, but is poor when excessive beam tailing distorts the assumed Gaussian electron intensity distributions. Beam tailing occurs in low-Z materials because of fast secondary electrons and in high-Z materials because of plural scattering.
Silicon crystallization in nanodot arrays organized by block copolymer lithography

NASA Astrophysics Data System (ADS)

Perego, Michele; Andreozzi, Andrea; Seguini, Gabriele; Schamm-Chardon, Sylvie; Castro, Celia; BenAssayag, Gerard

2014-12-01

Asymmetric polystyrene- b-polymethylmethacrylate (PS- b-PMMA) block copolymers are used to fabricate nanoporous PS templates with different pore diameter depending on the specific substrate neutralization protocol. The resulting polymeric templates are used as masks for the subsequent deposition of a thin ( h = 5 nm) amorphous Si layer by electron beam evaporation. After removal of the polymeric film and of the silicon excess, well-defined hexagonally packed amorphous Si nanodots are formed on the substrate. Their average diameter ( d < 20 nm), density (1.2 × 1011 cm-2), and lateral distribution closely mimic the original nanoporous template. Upon capping with SiO2 and high temperature annealing (1050 °C, N2), each amorphous Si nanodot rearranges in agglomerates of Si nanocrystals ( d < 4 nm). The average diameter and shape of these Si nanocrystals strongly depend on the size of the initial Si nanodot.
[Retinal vessels before and after photocoagulation in diabetic retinopathy. Determining the diameter using digitized color fundus slides].

PubMed

Remky, A; Arend, O; Beausencourt, E; Elsner, A E; Bertram, B

1996-01-01

Retinal vessel diameter is an important parameter in blood flow analysis. Despite modern digital image technology, most clinical studies investigate diameters subjectively using projected fundus slides or negatives. In the present study we used a technique to examine vessel diameters by digital image analysis of color fundus slides. We investigated in a retrospective manner diameter changes in twenty diabetic patients before and after panretinal laser coagulation. Color fundus slides were digitized by a new high resolution scanning device. The resulting images consisted in three channels (red, green, blue). Since vessel contrast was the highest in the green channel, we assessed grey value profiles perpendicular to the vessels in the green channel. Diameters were measured at the half-height of the profile. After panretinal laser coagulation, average venous diameter was decreased, whereas arterial diameter remained unchanged. There was no significant relation between the diameter change and the number of laser burns or the presence of neovascularization. Splitting digitized images into color planes enables objective measurements of retinal diameters in conventional color slides.
7 CFR 51.1323 - Serious damage.

Code of Federal Regulations, 2012 CFR

2012-01-01

... under the definition of russeting. (7) Insects: (i) Worm holes. More than three healed codling moth... insect stings affecting the appearance to an equal extent. 2 (ii) Blister mite or canker worm injury...
Microcalcification detectability using a bench-top prototype photon-counting breast CT based on a Si strip detector.

PubMed

Cho, Hyo-Min; Ding, Huanjun; Barber, William C; Iwanczyk, Jan S; Molloi, Sabee

2015-07-01

To investigate the feasibility of detecting breast microcalcification (μCa) with a dedicated breast computed tomography (CT) system based on energy-resolved photon-counting silicon (Si) strip detectors. The proposed photon-counting breast CT system and a bench-top prototype photon-counting breast CT system were simulated using a simulation package written in matlab to determine the smallest detectable μCa. A 14 cm diameter cylindrical phantom made of breast tissue with 20% glandularity was used to simulate an average-sized breast. Five different size groups of calcium carbonate grains, from 100 to 180 μm in diameter, were simulated inside of the cylindrical phantom. The images were acquired with a mean glandular dose (MGD) in the range of 0.7-8 mGy. A total of 400 images was used to perform a reader study. Another simulation study was performed using a 1.6 cm diameter cylindrical phantom to validate the experimental results from a bench-top prototype breast CT system. In the experimental study, a bench-top prototype CT system was constructed using a tungsten anode x-ray source and a single line 256-pixels Si strip photon-counting detector with a pixel pitch of 100 μm. Calcium carbonate grains, with diameter in the range of 105-215 μm, were embedded in a cylindrical plastic resin phantom to simulate μCas. The physical phantoms were imaged at 65 kVp with an entrance exposure in the range of 0.6-8 mGy. A total of 500 images was used to perform another reader study. The images were displayed in random order to three blinded observers, who were asked to give a 4-point confidence rating on each image regarding the presence of μCa. The μCa detectability for each image was evaluated by using the average area under the receiver operating characteristic curve (AUC) across the readers. The simulation results using a 14 cm diameter breast phantom showed that the proposed photon-counting breast CT system can achieve high detection accuracy with an average AUC greater than 0.89 ± 0.07 for μCas larger than 120 μm in diameter at a MGD of 3 mGy. The experimental results using a 1.6 cm diameter breast phantom showed that the prototype system can achieve an average AUC greater than 0.98 ± 0.01 for μCas larger than 140 μm in diameter using an entrance exposure of 1.2 mGy. The proposed photon-counting breast CT system based on a Si strip detector can potentially offer superior image quality to detect μCa with a lower dose level than a standard two-view mammography.
Protecting Yourself from Sun Exposure

MedlinePlus

... of a topical moisturizing cream, aloe, or 1% hydrocortisone cream may provide additional relief. If blistering occurs: ■■ ... may be removed and an antiseptic ointment or hydrocortisone cream may be applied. Seek medical attention if ...
Coping with Cold Sores

MedlinePlus

... Staying Safe Videos for Educators Search English Español Cold Sores KidsHealth / For Kids / Cold Sores What's in ... sore." What's that? Adam wondered. What Is a Cold Sore? Cold sores are small blisters that is ...
Hybrids of sugar pine by embryo culture

Treesearch

E. C. Stone; J. W. Duffield

1950-01-01

A modified embryo culture technique was used to facilitate germination of seed obtained after pollinating sugar pine with pollen from blister rust- resistant Armand and Korean pines. Resulting seedlings appear to be hybrids.
Heritable Disorders of Connective Tissue

MedlinePlus

... skin. Epidermolysis bullosa affects the skin, causing blisters. Marfan syndrome can affect the heart, blood vessels, lungs, eyes, ... Disorders of Connective Tissue, Questions and Answers about Marfan Syndrome, Questions and Answers about Marfan Syndrome, Easy-to- ...
Spider Bites (For Parents)

MedlinePlus

... Videos for Educators Search English Español First Aid: Spider Bites KidsHealth / For Parents / First Aid: Spider Bites ... rare. Signs and Symptoms Of a brown recluse spider bite: red blister in the center with surrounding ...
Poison Ivy, Oak, and Sumac

MedlinePlus

... on your skin, it causes a blistering skin rash. The rash can range from mild to severe, depending on ... respiratory system. The best way to avoid the rash is to learn what the plants look like ...
Porphyrin Test: MedlinePlus Lab Test Information

MedlinePlus

... cause skin symptoms when you are exposed to sunlight Some porphyrias affect both the nervous system and ... Hallucinations Symptoms of cutaneous porphyria include: Oversensitivity to sunlight Blisters on skin exposed to sunlight Redness and ...
21 CFR 1314.110 - Reports for mail-order sales.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...
21 CFR 1314.110 - Reports for mail-order sales.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...
21 CFR 1314.110 - Reports for mail-order sales.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...
21 CFR 1314.110 - Reports for mail-order sales.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...
21 CFR 1314.110 - Reports for mail-order sales.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...
Impetigo: Tips for Treatment and Prevention

MedlinePlus

... caused by one of two bacteria: group A streptococcus, which is the bacteria also responsible for strep throat, or staphylococcus. If impetigo is caused by streptococcus it will begin with tiny blisters that eventually ...
Development of beryllium-based neutron target system with three-layer structure for accelerator-based neutron source for boron neutron capture therapy.

PubMed

Kumada, Hiroaki; Kurihara, Toshikazu; Yoshioka, Masakazu; Kobayashi, Hitoshi; Matsumoto, Hiroshi; Sugano, Tomei; Sakurai, Hideyuki; Sakae, Takeji; Matsumura, Akira

2015-12-01

The iBNCT project team with University of Tsukuba is developing an accelerator-based neutron source. Regarding neutron target material, our project has applied beryllium. To deal with large heat load and blistering of the target system, we developed a three-layer structure for the target system that includes a blistering mitigation material between the beryllium used as the neutron generator and the copper heat sink. The three materials were bonded through diffusion bonding using a hot isostatic pressing method. Based on several verifications, our project chose palladium as the intermediate layer. A prototype of the neutron target system was produced. We will verify that sufficient neutrons for BNCT treatment are generated by the device in the near future. Copyright © 2015 Elsevier Ltd. All rights reserved.
Tensin stabilizes integrin adhesive contacts in Drosophila.

PubMed

Torgler, Catherine N; Narasimha, Maithreyi; Knox, Andrea L; Zervas, Christos G; Vernon, Matthew C; Brown, Nicholas H

2004-03-01

We report the functional characterization of the Drosophila ortholog of tensin, a protein implicated in linking integrins to the cytoskeleton and signaling pathways. A tensin null was generated and is viable with wing blisters, a phenotype characteristic of loss of integrin adhesion. In tensin mutants, mechanical abrasion is required during wing expansion to cause wing blisters, suggesting that tensin strengthens integrin adhesion. The localization of tensin requires integrins, talin, and integrin-linked kinase. The N-terminal domain and C-terminal PTB domain of tensin provide essential recruitment signals. The intervening SH2 domain is not localized on its own. We suggest a model where tensin is recruited to sites of integrin adhesion via its PTB and N-terminal domains, localizing the SH2 domain so that it can interact with phosphotyrosine-containing proteins, which stabilize the integrin link to the cytoskeleton.

Kindler syndrome: report of three cases in a family and a brief review.

PubMed

Yazdanfar, Ameneh; Hashemi, Banafsheh

2009-02-01

Kindler syndrome is an autosomal recessive disorder with neonatal blister formation, photosensitivity, atrophy, abnormal pigmentation, and fragility of the skin. Skin atrophy is more prominent on the extremities and the skin manifestations improve with age. We report three cases in a family which present the clinical and pathologic manifestations of Kindler syndrome. All of the three cases reported here present skin changes on the extremities, face, and neck, including hyper- and hypopigmentation, atrophy, and telangiectasia. The condition in these cases started soon after birth. Two of these cases also had mucosal involvement. Increased photosensitivity and sunburn after minimal sun exposure should lead physicians to examine the skin for poikiloderma and the mouth for fragility of the gums, periodontitis and other associated findings. Also, patients should be questioned about any history of blister formation as well as family history.
Workshop proceedings: research and management in whitebark pine ecosystems

USGS Publications Warehouse

Kendall, Katherine C.; Coen, Brenda

1994-01-01

The purpose of this workshop is to exchange information on on-going and soon-to-be-initiated whitebark pine research and management projects. By doing so we hope to encourage future work on this valuable species. We also hope to promote the use of consistent methods for evaluation and investigation of whitebark pine, and to provide avenues of collaboration. Speakers will present information on a variety of topics related to whitebark pine management and research. Featured presentation topics include anthropomorphic utilization of whitepark pine forests, whitebark pine natural regeneration, blister rust and the decline of whitebark pine, blister rust resistance studies, ecological mapping of the species, restoration and management projects, and survey/monitoring techniques. Information gained from these presentations may hopefully be used in the planning of future projects for the conservation of whitebark pine.
Comparison of cotton and acrylic socks using a generic cushion sole design for runners.

PubMed

Herring, K M; Richie, D H

1993-09-01

A longitudinal single-blind study was conducted to test the friction blister prevention properties of synthetic acrylic socks in a generic construction. This study serves as a comparison with the authors' previous work comparing acrylic and cotton socks in a patented padded construction. Twenty-seven long-distance runners provided data regarding dampness, temperature, friction blister incidence, severity, and size. Two different socks were tested; each was identical in every aspect of construction except the fiber content. One test sock was composed of 100% synthetic acrylic fibers, and the other was composed of 100% natural cotton fibers. These results were unsuccessful at demonstrating any superiority of cotton or acrylic fibers when knitting produced a generic "cushion sole" sock. The superiority of acrylic fibers has thus far been demonstrated only when sock knitting provides adequate anatomical padding [corrected].
GM-CSF modulates autoantibody production and skin blistering in experimental epidermolysis bullosa acquisita.

PubMed

Samavedam, Unni Krishna S R L; Iwata, Hiroaki; Müller, Susen; Schulze, Franziska S; Recke, Andreas; Schmidt, Enno; Zillikens, Detlef; Ludwig, Ralf J

2014-01-15

GM-CSF activates hematopoietic cells and recruits neutrophils and macrophages to sites of inflammation. Inhibition of GM-CSF attenuates disease activity in models of chronic inflammatory disease. Effects of GM-CSF blockade were linked to modulation of the effector phase, whereas effects on early pathogenic events, for example, Ab production, have not been identified. To evaluate yet uncharacterized effects of GM-CSF on early pathogenic events in chronic inflammation, we employed immunization-induced epidermolysis bullosa acquisita (EBA), an autoimmune bullous disease caused by autoantibodies to type VII collagen. Compared to wild-type mice, upon immunization, GM-CSF(-/-) mice produced lower serum autoantibody titers, which were associated with reduced neutrophil numbers in draining lymph nodes. The same effect was observed in neutrophil-depleted wild-type mice. Neutrophil depletion in GM-CSF(-/-) mice led to a stronger inhibition, indicating that GM-CSF and neutrophils have additive functions. To characterize the contribution of GM-CSF specifically in the effector phase of EBA, disease was induced by transfer of anti-type VII collagen IgG into mice. We observed an increased GM-CSF expression, and GM-CSF blockade reduced skin blistering. Additionally, GM-CSF enhanced reactive oxygen species release and neutrophil migration in vitro. In immunization-induced murine EBA, treatment with anti-GM-CSF had a beneficial effect on established disease. We demonstrate that GM-CSF modulates both autoantibody production and skin blistering in a prototypical organ-specific autoimmune disease.
Impact on the deuterium retention of simultaneous exposure of tungsten to a steady state plasma and transient heat cycling loads

NASA Astrophysics Data System (ADS)

Huber, A.; Sergienko, G.; Wirtz, M.; Steudel, I.; Arakcheev, A.; Brezinsek, S.; Burdakov, A.; Dittmar, T.; Esser, H. G.; Kreter, A.; Linke, J.; Linsmeier, Ch; Mertens, Ph; Möller, S.; Philipps, V.; Pintsuk, G.; Reinhart, M.; Schweer, B.; Shoshin, A.; Terra, A.; Unterberg, B.

2016-02-01

The impact on the deuterium retention of simultaneous exposure of tungsten to a steady-state plasma and transient cyclic heat loads has been studied in the linear PSI-2 facility with the main objective of qualifying tungsten (W) as plasma-facing material. The transient heat loads were applied by a high-energy laser, a Nd:YAG laser (λ = 1064 nm) with an energy per pulse of up to 32 J and a duration of 1 ms. A pronounced increase in the D retention by a factor of 13 has been observed during the simultaneous transient heat loads and plasma exposure. These data indicate that the hydrogen clustering is enhanced by the thermal shock exposures, as seen on the increased blister size due to mobilization and thermal production of defects during transients. In addition, the significant increase of the D retention during the simultaneous loads could be explained by an increased diffusion of D atoms into the W material due to strong temperature gradients during the laser pulse exposure and to an increased mobility of D atoms along the shock-induced cracks. Only 24% of the retained deuterium is located inside the near-surface layer (d<4 μm). Enhanced blister formation has been observed under combined loading conditions at power densities close to the threshold for damaging. Blisters are not mainly responsible for the pronounced increase of the D retention.
Males of a Strongly Polygynous Species Consume More Poisonous Food than Females

PubMed Central

Bravo, Carolina; Bautista, Luis Miguel; García-París, Mario; Blanco, Guillermo; Alonso, Juan Carlos

2014-01-01

We present evidence of a possible case of self-medication in a lekking bird, the great bustard Otis tarda. Great bustards consumed blister beetles (Meloidae), in spite of the fact that they contain cantharidin, a highly toxic compound that is lethal in moderate doses. In addition to anthelminthic properties, cantharidin was effective against gastrointestinal bacteria that cause sexually-transmitted diseases. Although both sexes consumed blister beetles during the mating season, only males selected them among all available insects, and ingested more and larger beetles than females. The male-biased consumption suggests that males could use cantharidin to reduce their parasite load and increase their sexual attractiveness. This plausibly explains the intense cloaca display males perform to approaching females, and the meticulous inspection females conduct of the male's cloaca, a behaviour only observed in this and another similar species of the bustard family. A white, clean cloaca with no infection symptoms (e.g., diarrhoea) is an honest signal of both, resistance to cantharidin and absence of parasites, and represents a reliable indicator of the male quality to the extremely choosy females. Our results do not definitely prove, but certainly strongly suggest that cantharidin, obtained by consumption of blister beetles, acts in great bustards as an oral anti-microbial and pathogen-limiting compound, and that males ingest these poisonous insects to increase their mating success, pointing out that self-medication might have been overlooked as a sexually-selected mechanism enhancing male fitness. PMID:25337911
Interleukin-16 expression and release in bullous pemphigoid

PubMed Central

FREZZOLINI, A; CIANCHINI, G; RUFFELLI, M; CADONI, S; PUDDU, P; DE PITÀ, O

2004-01-01

Cutaneous infiltration of activated CD4+ T cells and eosinophils is an early event in blister formation during bullous pemphigoid (BP), suggesting that the trafficking of circulating leucocytes through the sites of inflammation, their activation and cytokine release is crucial in the pathogenesis of the disease. IL-16 is a major chemotactic factor able to recruit CD4+ cells in the skin during inflammation and to induce the expression of functional high-affinity interleukin (IL)-2 receptors, thus contributing to cellular activation and proliferation. We performed a study in order to evaluate the presence of IL-16 in skin samples and sera and blister fluids of patients affected with BP in active phase of the disease (n = 39), compared with healthy donors studied as control group. Ten patients were also evaluated before and after steroid therapy. Our results demonstrated that IL-16 was expressed strongly by keratinocytes and by dermal infiltrating CD4+ T lymphocytes in lesional skin of BP patients. High levels of IL-16 were detected in sera and blisters of BP, significantly higher in respect to healthy donors. When patients were investigated for the presence of eosinophil cationic protein (ECP) and soluble CD30 (sCD30) to reveal signs of eosinophils and Th2-cells activation, we found a positive correlation between IL-16 serum levels and both ECP and sCD30, suggesting that IL-16 is involved in Th2 lymphocytes and eosinophils recruitment during BP. PMID:15320912
Contact Lenses Wettability In Vitro: Effect of Surface-Active Ingredients

PubMed Central

Lin, Meng C.; Svitova, Tatyana F.

2010-01-01

Purpose To investigate the release of surface-active agents (surfactants) from unworn soft contact lenses and their influence on the lens surface wettability in vitro. Methods Surface tension (ST) of blister pack solutions was measured by pendant-drop technique. STs at the air-aqueous interface and contact angles (CAs) of four conventional and seven silicone hydrogel (SiH) soft contact lenses (SCLs) were evaluated in a dynamic-cycling regime using a modified captive-bubble tensiometer-goniometer. Measurements were performed immediately after removal from blister packs, and after soaking in a glass vial filled with a surfactant-free solution, which was replaced daily for one week. Lens surface wettability was expressed as adhesion energy (AE) according to Young’s equation. Results STs of all blister pack solutions were lower than the reference ST of pure water (72.5 mN/m), indicating the presence of surfactants. When lenses were depleted of surfactants by soaking, the STs of all studied lenses and advancing CAs of selected lenses increased (p < 0.001). Receding CAs of all studied lenses were 12° ± 5° and were not affected by the presence of surfactants. For most of the conventional lenses, the surface wettability was largely dependent on surfactants, and reduced significantly after surfactant depletion. In contrast, most SiH lenses exhibited stable and self-sustained surface wettability in vitro. Conclusions The manufacturer-added surfactants affected wetting properties of all studied SCLs, although to different degrees. PMID:20400924
Packaging of pharmaceuticals: still too many dangers but several encouraging initiatives.

PubMed

2007-06-01

(1) In 2006 in France, several drugs sold in poorly designed packaging exposed patients to a risk of serious adverse effects. (2) In 2006, Prescrire used a standardised methodology to examine the packaging of all new pharmaceutical products (656 different boxes) assessed in the New Products section of our French edition, la revue Prescrire. About 75% of these boxes contained tablets or capsules, mostly in blister packs. (3) Poor labelling remains a major problem. The international nonproprietary names (INN) is hard to spot on most boxes of patented brand-name drugs and is often overshadowed by the brand name. The primary packaging of many products does not even include the INN. (4) Two particularly ambiguous types of labelling are becoming more common on blister packs: pre-cut multiple-unit blister packs on which the labelling is truncated when a unit blister is removed; and blister packs on which the labelling spans two blisters, creating a risk of overdose. (5) The use of colours is frequently inappropriate. In particular, irrelevant information is often highlighted unnecessarily, while other, important information is barely visible. (6) Too many devices for oral administration create a risk of misuse. Very few are graduated in units of weight. Most are graduated in millilitres, obliging caregivers to use conversion charts and thus creating a risk of dosing errors. Devices graduated in kg bodyweight can also lead to dosing errors. (7) The labelling of some injectable drugs is barely legible. The various models of plastic ampoules, that are gradually replacing glass ampoules, can represent a danger because they resemble other plastic ampoules containing products administered by different routes. Packaging that does not provide a syringe or needle can cause problems for caregivers and represents another potential source of error. (8) Many of the patient information leaflets examined in 2006 had the same flaws as previously observed, i.e. uneven information quality, discrepancies between different sections, and out-of-date information. More and more French leaflets now include insets offering "Health Advice". There are better and worse examples, but there is no guarantee that they have been properly reviewed by the regulatory agency. (9) Increasingly drug boxes include pictograms, even though several studies have shown they are often difficult to interpret. And most boxes of generics also now include standard dosing schedules that are not always appropriate and may create a risk of dosing errors with potentially serious consequences. (10) 67 multidose bottles examined in 2006 had no childproof safety cap. Some contained psychotropics, which can have life-threatening effects if accidentally consumed in large amounts. (11) Some manufacturers have adopted realistic solutions to these problems. In particular, generics manufacturers again improved product labelling in 2006 (emphasis on the INN), appropriate use of colours for dose differentiation, and, encouragingly, far more Braille labels. (12) In 2006, the French regulatory agency introduced several measures aimed at improving the labelling of ampoules containing some injectable drugs. The impact of these measures was visible on several products marketed in 2006, including plastic vials of solutions for nebulization. (13) Several other examples of well-designed packaging were seen: safety devices on prefilled syringes; a childproof safety device; a tamperproof ring; unit-dose blister packs; clearly written patient leaflets; and the use of clear and appropriate symbols and pictograms. (14) In practice, in view of the large number of incidents recorded in 2006, and the plethora of packaging designs, caregivers should take time to analyse and discuss drug packaging. In this way, they will be in a position to distinguish between good and bad drug packaging, and to anticipate the risks associated with poorly designed packaging. (15) There are many ways in which drug regulatory authorities can help to ensure that drugs are sold in safe packaging. The French regulatory agency's work on the labelling of injectable drugs is an encouraging step. European Directive 2004/27/EC on medicines for human use provides for improvements in labelling (e.g. Braille) and patient information leaflets. Transposition of these measures into French law should lead to a number of improvements, provided the relevant regulations and guidelines place patients' interests first.
Technical note: estimating absorbed doses to the thyroid in CT.

PubMed

Huda, Walter; Magill, Dennise; Spampinato, Maria V

2011-06-01

To describe a method for estimating absorbed doses to the thyroid in patients undergoing neck CT examinations. Thyroid doses in anthropomorphic phantoms were obtained for all 23 scanner dosimetry data sets in the ImPACT CT patient dosimetry calculator. Values of relative thyroid dose [R(thy)(L)], defined as the thyroid dose for a given scan length (L) divided by the corresponding thyroid dose for a whole body scan, were determined for neck CT scans. Ratios of the maximum thyroid dose to the corresponding CTDI(vol) and [D'(thy)], were obtained for two phantom diameters. The mass-equivalent water cylinder of any patient can be derived from the neck cross-sectional area and the corresponding average Hounsfield Unit, and compared to the 16.5-cm diameter water cylinder that models the ImPACT anthropomorphic phantom neck. Published values of relative doses in water cylinders of varying diameter were used to adjust thyroid doses in the anthropomorphic phantom to those of any sized patient. Relative thyroid doses R(thy)(L) increase to unity with increasing scan length and with very small difference between scanners. A 10-cm scan centered on the thyroid would result in a dose that is, nearly 90% of the thyroid dose from a whole body scan when performed using the constant radiographic techniques. At 120 kV, the average value of D'(thy) for the 16-cm diameter was 1.17 +/- 0.05 and was independent of CT vendor and year of CT scanner, and choice of x-ray tube voltage. The corresponding average value of D'(thy) in the 32-cm diameter phantom was 2.28 +/- 0.22 and showed marked variations depending on vendor, year of introduction into clinical practice as well as x-ray tube voltage. At 120 kV, a neck equivalent to a 10-cm diameter cylinder of water would have thyroid doses 36% higher than those in the ImPACT phantom, whereas a neck equivalent to a 25-cm cylinder diameter would have thyroid doses 35% lower. Patient thyroid doses can be estimated by taking into account the amount of radiation used to perform the CT examination (CTDI(vol)) and accounting for scan length and patient anatomy (i.e., neck diameter) at the thyroid location.
Online prediction of organileptic data for snack food using color images

NASA Astrophysics Data System (ADS)

Yu, Honglu; MacGregor, John F.

2004-11-01

In this paper, a study for the prediction of organileptic properties of snack food in real-time using RGB color images is presented. The so-called organileptic properties, which are properties based on texture, taste and sight, are generally measured either by human sensory response or by mechanical devices. Neither of these two methods can be used for on-line feedback control in high-speed production. In this situation, a vision-based soft sensor is very attractive. By taking images of the products, the samples remain untouched and the product properties can be predicted in real time from image data. Four types of organileptic properties are considered in this study: blister level, toast points, taste and peak break force. Wavelet transform are applied on the color images and the averaged absolute value for each filtered image is used as texture feature variable. In order to handle the high correlation among the feature variables, Partial Least Squares (PLS) is used to regress the extracted feature variables against the four response variables.
Effect of tank geometry on its average performance

NASA Astrophysics Data System (ADS)

Orlov, Aleksey A.; Tsimbalyuk, Alexandr F.; Malyugin, Roman V.; Leontieva, Daria A.; Kotelnikova, Alexandra A.

2018-03-01

The mathematical model of non-stationary filling of vertical submerged tanks with gaseous uranium hexafluoride is presented in the paper. There are calculations of the average productivity, heat exchange area, and filling time of various volumes tanks with smooth inner walls depending on their "height : radius" ratio as well as the average productivity, degree, and filling time of horizontal ribbing tank with volume 6.10-2 m3 with change central hole diameter of the ribs. It has been shown that the growth of "height / radius" ratio in tanks with smooth inner walls up to the limiting values allows significantly increasing tank average productivity and reducing its filling time. Growth of H/R ratio of tank with volume 1.0 m3 to the limiting values (in comparison with the standard tank having H/R equal 3.49) augments tank productivity by 23.5 % and the heat exchange area by 20%. Besides, we have demonstrated that maximum average productivity and a minimum filling time are reached for the tank with volume 6.10-2 m3 having central hole diameter of horizontal ribs 6.4.10-2 m.
Estimating the board foot to cubic foot ratio

Treesearch

Steve P. Verrill; Victoria L. Herian; Henry N. Spelter

2004-01-01

Certain issues in recent softwood lumber trade negotiations have centered on the method for converting estimates of timber volumes reported in cubic meters to board feet. Such conversions depend on many factors; three of the most important of these are log length, diameter, and taper. Average log diameters vary by region and have declined in the western United States...
Diameter class volume tables for California old-growth timber

Treesearch

Duncan Dunning

1945-01-01

Tables giving average tree volumes by breast-height diameter classes frequently may be used in timber cruising to save money, time, and men. Such tables may be appropriate in cruises of large areas having many trees in low-intensity cruises warranting the sacrifice in accuracy that results from omission of individual tree height measurements, during wartime when men...
Projecting a Stand Table Through Time

Treesearch

Quang V. Cao; V. Clark Baldwin

1999-01-01

Stand tables provide number of trees per acre for each diameter class. This paper presents a general technique to predict a future stand table, based on the current stand table and future stand summary statistics such as trees and basal area per acre, and average diameter. The stand projection technique involves (a) predicting surviving trees for each class, and (b)...
Simulation study of poled low-water ionomers with different architectures

NASA Astrophysics Data System (ADS)

Allahyarov, Elshad; Taylor, Philip L.; Löwen, Hartmut

2011-11-01

The role of the ionomer architecture in the formation of ordered structures in poled membranes is investigated by molecular dynamics computer simulations. It is shown that the length of the sidechain Ls controls both the areal density of cylindrical aggregates Nc and the diameter of these cylinders in the poled membrane. The backbone segment length Lb tunes the average diameter Ds of cylindrical clusters and the average number of sulfonates Ns in each cluster. A simple empirical formula is noted for the dependence of the number density of induced rod-like aggregates on the sidechain length Ls within the parameter range considered in this study.
Studying the effects of nucleating agents on texture modification of puffed corn-fish snack.

PubMed

Shahmohammadi, Hamid Reza; Bakar, Jamilah; Rahman, Russly Abdul; Adzhan, Noranizan Mohd

2014-02-01

To improve textural attributes of puffed corn-fish snack, the effects of 1%, 1.5%, and 2% of calcium carbonate, magnesium silicate (talc), sodium bicarbonate as well as 5% and 10% of wheat bran (as the nucleating materials) on textural attributes were studied. Sensory evaluation, bulk density, expansion ratio, maximum force, and count peaks were measured using the Kramer test. The results showed that all of the additives except bran significantly enhanced the texture. Among them, talc at 0.5% was the best to enhance the density and expansion ratio. Effects of using 0.5% talc on puffed corn-fish snack microstructure were studied using scanning electron microscopy. The average cell diameter of 109 ± 48 μm and cell numbers per square centimeter of 67.4 for talc-treated products were obtained, while for nontalc-treated extrudates, average cell diameter of 798 ± 361 μm and cell numbers per square centimeter of 13.9 were found. Incorporation of 0.5% w/w of magnesium silicate reduced (7-fold) the average cell diameter while increased (4-fold) the cell number. © 2014 Institute of Food Technologists®
[Predictability of the corneal flap creation with the femtosecond laser in LASIK].

PubMed

Mai, Zhi-bin; Liu, Su-bing; Nie, Xiao-li; Sun, Hong-xia; Xin, Bao-li; Tang, Xiu-xia

2012-05-01

To observe the predictability of corneal flap creation with the FEMTO LDV femtosecond laser and analyze preliminarily the factors correlating to the thickness and diameter of the flap . It was a study of serial cases. 260 eyes of 130 consecutive patients were treated with the FEMTO LDV. The eyes were assigned to two groups according to intended flap thickness, 110 µm (208 eyes) and 90 µm (52 eyes). Intended flap diameter varied from 8.5 to 9.5 mm. Difference analysis of flap diameter and intended diameter as well as flap thickness and intended thickness were made. The data was analyzed with SPSS to sum up a multiple stepwise regression formula that could express their quantitative relationship. The 90 µm flap group had a average flap thickness of (95.12 ± 7.65) µm, while for the 110 µm group the average flap thickness was (104.81 ± 3.09) µm. The difference between right and left eyes was not statistically significant (t(110 µm) = -1.223, t(90 µm) = -1.343, P > 0.05). Corneal flap thickness was inversely correlated with flap diameter (r(110 µm) = -0.143, r(90 µm) = -0.315, P < 0.05), but was not related to preoperative patient age, corneal thickness, keratometric value K or intraocular pressure (r(110 µm) = -0.160, 0.054, -0.011, -0.363; r(90 µm) = 0.024, 0.074, -0.212, -0.434, all P > 0.05). Corneal flap diameter was positively correlated with preoperative corneal keratometric value K and thickness (P < 0.001, P < 0.05). Multiple stepwise regression analysis showed flap diameter was an influencing factor for flap thickness. Preoperative corneal keratometric value K and thickness were influencing factors for flap diameter. The LASIK flap creation with the FEMTO LDV laser has relatively good predictability. Flap diameter is an influencing factor for flap thickness.
Mouth ulcers

MedlinePlus

... Gingivostomatitis Herpes simplex ( fever blister ) Leukoplakia Oral cancer Oral lichen planus Oral thrush A skin sore caused by histoplasmosis may ... mouth Images Oral thrush Canker sore (aphthous ulcer) Lichen planus on the oral mucosa Mouth sores References Daniels TE, Jordan RC. ...
Malignant Melanoma of the Foot

MedlinePlus

... at greater risk for developing this type of cancer. These include: Fair skin; skin that freckles; blond or red hair Blistering sunburns before the age of 18 Numerous moles, especially if they appeared at a young age ...

How To Prevent and Treat Blisters

MedlinePlus

... Us Media contacts Advertising contacts AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2018 American Academy ... prohibited without prior written permission. AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2017 American Academy ...
7 CFR 51.1280 - Serious damage.

Code of Federal Regulations, 2012 CFR

2012-01-01

.... (5) Insects: (i) Worm holes. More than three healed codling moth stings, of which not more than two... appearance to an equal extent. 2 (ii) Blister mite or canker worm injury which affects an aggregate area of...
Warts

MedlinePlus

... form over warts on your foot or around nails. Your provider may recommend the following treatments if your warts do not go away: Stronger (prescription) medicines A blistering solution Freezing the wart ( cryotherapy ) to remove it Burning the wart ( electrocautery ) to ...
40 CFR 264.226 - Monitoring and inspection.

Code of Federal Regulations, 2011 CFR

2011-07-01

... absence of tears, punctures, or blisters; and (2) Soil-based and admixed liners and covers must be... dimensions, and level that avoids backup into the drainage layer and minimizes head in the sump. [47 FR 32357...
40 CFR 264.226 - Monitoring and inspection.

Code of Federal Regulations, 2012 CFR

2012-07-01

... absence of tears, punctures, or blisters; and (2) Soil-based and admixed liners and covers must be... dimensions, and level that avoids backup into the drainage layer and minimizes head in the sump. [47 FR 32357...
40 CFR 264.226 - Monitoring and inspection.

Code of Federal Regulations, 2014 CFR

2014-07-01

... absence of tears, punctures, or blisters; and (2) Soil-based and admixed liners and covers must be... dimensions, and level that avoids backup into the drainage layer and minimizes head in the sump. [47 FR 32357...
40 CFR 264.226 - Monitoring and inspection.

Code of Federal Regulations, 2013 CFR

2013-07-01

... absence of tears, punctures, or blisters; and (2) Soil-based and admixed liners and covers must be... dimensions, and level that avoids backup into the drainage layer and minimizes head in the sump. [47 FR 32357...
40 CFR 264.226 - Monitoring and inspection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... absence of tears, punctures, or blisters; and (2) Soil-based and admixed liners and covers must be... dimensions, and level that avoids backup into the drainage layer and minimizes head in the sump. [47 FR 32357...
Diabetic Complications and Amputation Prevention

MedlinePlus

... because of two complications of diabetes: nerve damage (neuropathy) and poor circulation. Neuropathy causes loss of feeling in your feet, taking ... to the bone. Because of poor circulation and neuropathy in the feet, cuts or blisters can easily ...
DOE Office of Scientific and Technical Information (OSTI.GOV)

Sommer, C. M., E-mail: christof.sommer@med.uni-heidelberg.de; Grenacher, L.; Stampfl, U.

The purpose of this study was to evaluate the impact of stent design on in-stent stenosis in rabbit iliac arteries. Four different types of stent were implanted in rabbit iliac arteries, being different in stent design (crown or wave) and strut thickness (50 or 100 {mu}m). Ten stents of each type were implanted. Each animal received one crown and one wave stent with the same strut thickness. Follow-up was either 12 weeks (n = 10 rabbits) or 24 weeks (n = 10 rabbits). Primary study end points were angiographic and microscopic in-stent stenosis. Secondary study end points were vessel injury,more » vascular inflammation, and stent endothelialization. Average stent diameter, relative stent overdilation, average and minimal luminal diameter, and relative average and maximum luminal loss were not significantly different. However, a trend to higher relative stent overdilation was recognized in crown stents compared to wave stents. A trend toward higher average and minimal luminal diameter and lower relative average and maximum luminal loss was recognized in crown stents compared to wave stents with a strut thickness of 100 {mu}m. Neointimal height, relative luminal area stenosis, injury score, inflammation score, and endothelialization score were not significantly different. However, a trend toward higher neointimal height was recognized in crown stents compared to wave stents with a strut thickness of 50 {mu}m and a follow-up of 24 weeks. In conclusion, in this study, crown stents seem to trigger neointima. However, the optimized radial force might equalize the theoretically higher tendency for restenosis in crown stents. In this context, also more favorable positive remodeling in crown stents could be important.« less
Model based optimization of driver-pickup separation for eddy current measurement of gap

NASA Astrophysics Data System (ADS)

Klein, G.; Morelli, J.; Krause, T. W.

2018-04-01

The fuel channels in CANDU® (CANada Deuterium Uranium) nuclear reactors consist of a pressure tube (PT) contained within a larger diameter calandria tube (CT). The separation between the tubes, known as the PT-CT gap, ensures PT hydride blisters, which could lead to potential cracking of the PT, do not develop. Therefore, accurate measurements are required to confirm that contact between PT and CT is not imminent. Gap measurement uses an eddy current probe. However this probe is sensitive to lift-off variations, which can adversely affect estimated gap. A validated analytical flat plate model of eddy current response to gap was used to examine the effect of driver-pickup spacing on lift-off and response to gap at a frequency of 4 kHz, which is used for in-reactor measurements. This model was compared against, and shown to have good agreement with, a COMSOL® finite element method (FEM) model. The optimum coil separation, which included the constraint of coil size, was found to be 11 mm, resulting in a phase response between lift-off and response to change in gap of 66°. This work demonstrates the advantages of using analytical models for optimizing coil designs for measurement of parameters that may negatively influence the outcome of an inspection measurement.
Nonablative laser treatment of facial rhytides

NASA Astrophysics Data System (ADS)

Lask, Gary P.; Lee, Patrick K.; Seyfzadeh, Manouchehr; Nelson, J. Stuart; Milner, Thomas E.; Anvari, Bahman; Dave, Digant P.; Geronemus, Roy G.; Bernstein, Leonard J.; Mittelman, Harry; Ridener, Laurie A.; Coulson, Walter F.; Sand, Bruce; Baumgarder, Jon; Hennings, David R.; Menefee, Richard F.; Berry, Michael J.

1997-05-01

The purpose of this study is to evaluate the safety and effectiveness of the New Star Model 130 neodymium:yttrium aluminum garnet (Nd:YAG) laser system for nonablative laser treatment of facial rhytides (e.g., periorbital wrinkles). Facial rhytides are treated with 1.32 micrometer wavelength laser light delivered through a fiberoptic handpiece into a 5 mm diameter spot using three 300 microsecond duration pulses at 100 Hz pulse repetition frequency and pulse radiant exposures extending up to 12 J/cm2. Dynamic cooling is used to cool the epidermis selectively prior to laser treatment; animal histology experiments confirm that dynamic cooling combined with nonablative laser heating protects the epidermis and selectively injures the dermis. In the human clinical study, immediately post-treatment, treated sites exhibit mild erythema and, in a few cases, edema or small blisters. There are no long-term complications such as marked dyspigmentation and persistent erythema that are commonly observed following ablative laser skin resurfacing. Preliminary results indicate that the severity of facial rhytides has been reduced, but long-term follow-up examinations are needed to quantify the reduction. The mechanism of action of this nonablative laser treatment modality may involve dermal wound healing that leads to long- term synthesis of new collagen and extracellular matrix material.
Bullous cryothermic dermatitis artefacta induced by deodorant spray abuse.

PubMed

Jacobi, A; Bender, A; Hertl, M; König, A

2011-08-01

Dermatitis artefacta belongs to a broad spectrum of factitious diseases of lesions usually self-induced by patients. Here we report a surprisingly effective induction of blisters and thermic dermatitis by excessive abuse of common deodorant sprays. We evaluated the clinical course and outcome in three patients with dermatitis artefacta induced by deodorant spray. A 12-year-old boy only admitted the abuse of deodorant spray after psychiatric intervention. Two adults (21-year-old and 37-year-old women) had borderline personality disorder and frankly reported the urge to induce pain by spraying for at least 100 s at a short distance. Bullous dermatitis was the acute presenting sign in all patients. The bullae were found on the extensor surfaces of the extremities, with a distribution of older lesions showing erosions and scarring and fresh lesions with intact bullae with a diameter of 3-15 cm. After searching for the causative agent and removal of the deodorant spray, clinical outcome showed a healing without and with scars. Cryo-damage by abuse of common deodorant sprays seems to become a popular mechanism by which an impressive bullous dermatitis can be artificially induced. Dermatologists and psychiatrist should be aware of this method of injury. © 2010 The Authors. Journal of the European Academy of Dermatology and Venereology © 2010 European Academy of Dermatology and Venereology.
Microscopic aspects of autoschizic cell death in human ovarian carcinoma (2774) cells following vitamin C, vitamin K3 or vitamin C:K3 treatment.

PubMed

Gilloteaux, Jacques; Jamison, James M; Arnold, David; Taper, Henryk S; Von Gruenigen, Vivian E; Summers, Jack L

2003-08-01

Human ovarian carcinoma cells (MDAH 2774) were treated with sodium ascorbate (VC), menadione (VK3), or with a VC:VK3 combination for 1 h and then studied using light microscopy (LM) and scanning (SEM) and transmission electron (TEM) microscopy. Plasma membrane damage (blisters and blebs, hairy aspect) results from vitamin C (VC) treatment, while cytoskeletal damage and self-morsellation are caused by vitamin K3 (VK3) treatment. VC:VK3-treated cells exhibit exacerbated injuries characteristic of both VC and VK3 treatment as well as a significant decrease in cell diameters from 20-35 microm for control cells to 7-12 microm for VC:VK3 treatment. Moreover, after a 1-h exposure to the vitamin combination, autoschizis (43%), apoptosis (3%), and oncosis (1.9%) are observed at the percentages indicated. All cellular changes associated with autoschizis observed with SEM were confirmed by LM and TEM observations and are consistent with cell death by autoschizis: decrease in cell size, cytoplasmic self-excisions, degradation of the nucleus and nucleolus without formation of apoptotic bodies and, ultimately, karyorrhexis and karyolysis. These results also suggest that the vitamin combination may find clinical use in the treatment of ovarian cancer.
Microscopic Aspects of Autoschizic Cell Death in Human Ovarian Carcinoma (2774) Cells Following Vitamin C, Vitamin K3 or Vitamin C:K3 Treatment

NASA Astrophysics Data System (ADS)

Gilloteaux, Jacques; Jamison, James M.; Arnold, David; Taper, Henryk S.; von Gruenigen, Vivian E.; Summers, Jack L.

2003-08-01

Human ovarian carcinoma cells (MDAH 2774) were treated with sodium ascorbate (VC), menadione (VK3), or with a VC:VK3 combination for 1 h and then studied using light microscopy (LM) and scanning (SEM) and transmission electron (TEM) microscopy. Plasma membrane damage (blisters and blebs, hairy aspect) results from vitamin C (VC) treatment, while cytoskeletal damage and self-morsellation are caused by vitamin K3 (VK3) treatment. VC:VK3-treated cells exhibit exacerbated injuries characteristic of both VC and VK3 treatment as well as a significant decrease in cell diameters from 20 35 [mu]m for control cells to 7 12 [mu]m for VC:VK3 treatment. Moreover, after a 1-h exposure to the vitamin combination, autoschizis (43%), apoptosis (3%), and oncosis (1.9%) are observed at the percentages indicated. All cellular changes associated with autoschizis observed with SEM were confirmed by LM and TEM observations and are consistent with cell death by autoschizis: decrease in cell size, cytoplasmic self-excisions, degradation of the nucleus and nucleolus without formation of apoptotic bodies and, ultimately, karyorrhexis and karyolysis. These results also suggest that the vitamin combination may find clinical use in the treatment of ovarian cancer.
Effect of hole geometry and Electric-Discharge Machining (EDM) on airflow rates through small diameter holes in turbine blade material

NASA Technical Reports Server (NTRS)

Hippensteele, S. A.; Cochran, R. P.

1980-01-01

The effects of two design parameters, electrode diameter and hole angle, and two machine parameters, electrode current and current-on time, on air flow rates through small-diameter (0.257 to 0.462 mm) electric-discharge-machined holes were measured. The holes were machined individually in rows of 14 each through 1.6 mm thick IN-100 strips. The data showed linear increase in air flow rate with increases in electrode cross sectional area and current-on time and little change with changes in hole angle and electrode current. The average flow-rate deviation (from the mean flow rate for a given row) decreased linearly with electrode diameter and increased with hole angle. Burn time and finished hole diameter were also measured.
Effect of lung and target density on small-field dose coverage and PTV definition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Higgins, Patrick D., E-mail: higgi010@umn.edu; Ehler, Eric D.; Cho, Lawrence C.

We have studied the effect of target and lung density on block margin for small stereotactic body radiotherapy (SBRT) targets. A phantom (50 × 50 × 50 cm{sup 3}) was created in the Pinnacle (V9.2) planning system with a 23-cm diameter lung region of interest insert. Diameter targets of 1.6, 2.0, 3.0, and 4.0 cm were placed in the lung region of interest and centered at a physical depth of 15 cm. Target densities evaluated were 0.1 to 1.0 g/cm{sup 3}, whereas the surrounding lung density was varied between 0.05 and 0.6 g/cm{sup 3}. A dose of 100 cGy wasmore » delivered to the isocenter via a single 6-MV field, and the ratio of the average dose to points defining the lateral edges of the target to the isocenter dose was recorded for each combination. Field margins were varied from none to 1.5 cm in 0.25-cm steps. Data obtained in the phantom study were used to predict planning treatment volume (PTV) margins that would match the clinical PTV and isodose prescription for a clinical set of 39 SBRT cases. The average internal target volume (ITV) density was 0.73 ± 0.17, average local lung density was 0.33 ± 0.16, and average ITV diameter was 2.16 ± 0.8 cm. The phantom results initially underpredicted PTV margins by 0.35 cm. With this offset included in the model, the ratio of predicted-to-clinical PTVs was 1.05 ± 0.32. For a given target and lung density, it was found that treatment margin was insensitive to target diameter, except for the smallest (1.6-cm diameter) target, for which the treatment margin was more sensitive to density changes than the larger targets. We have developed a graphical relationship for block margin as a function of target and lung density, which should save time in the planning phase by shortening the design of PTV margins that can satisfy Radiation Therapy Oncology Group mandated treatment volume ratios.« less
Diameter control of single-walled carbon nanotube forests from 1.3–3.0 nm by arc plasma deposition

PubMed Central

Chen, Guohai; Seki, Yasuaki; Kimura, Hiroe; Sakurai, Shunsuke; Yumura, Motoo; Hata, Kenji; Futaba, Don N.

2014-01-01

We present a method to both precisely and continuously control the average diameter of single-walled carbon nanotubes in a forest ranging from 1.3 to 3.0 nm with ~1 Å resolution. The diameter control of the forest was achieved through tuning of the catalyst state (size, density, and composition) using arc plasma deposition of nanoparticles. This 1.7 nm control range and 1 Å precision exceed the highest reports to date. PMID:24448201
Stand Density and Canopy Gaps

Treesearch

Boris Zeide

2004-01-01

Estimation of stand density is based on a relationship between number of trees and their average diameter in fully stocked stands. Popular measures of density (Reinekeâs stand density index and basal area) assume that number of trees decreases as a power function of diameter. Actually, number of trees drops faster than predicted by the power function because the number...
Mesavage and Girard form class taper functions derived from profile equations

Treesearch

Thomas g. Matney; Emily B. Schultz

2007-01-01

The Mesavage and Girard (1946) average upper-log taper tables remain a favorite way of estimating tree bole volume because they only require the measurement of merchantable (useable) height to an indefinite top diameter limit. For the direct application of profile equations, height must be measured to a definite top diameter limit, and this makes the collection of data...

Essential features of long-term changes of areas and diameters of sunspot groups in solar activity cycles 12-24

NASA Astrophysics Data System (ADS)

Efimenko, V. M.; Lozitsky, V. G.

2018-06-01

We analyze the Greenwich catalog data on areas of sunspot groups of last thirteen solar cycles. Various parameters of sunspots are considered, namely: average monthly smoothed areas, maximum area for each year and equivalent diameters of groups of sunspots. The first parameter shows an exceptional power of the 19th cycle of solar activity, which appears here more contrastively than in the numbers of spots (that is, in Wolf's numbers). It was found that in the maximum areas of sunspot groups for a year there is a unique phenomenon: a short and high jump in the 18th cycle (in 1946-1947) that has no analogues in other cycles. We also studied the integral distributions for equivalent diameters and found the following: (a) the average value of the index of power-law approximation is 5.4 for the last 13 cycles and (b) there is reliable evidence of Hale's double cycle (about 44 years). Since this indicator reflects the dispersion of sunspot group diameters, the results obtained show that the convective zone of the Sun generates embryos of active regions in different statistical regimes which change with a cycle of about 44 years.
Relationship between the tensile strengths and diameters of human umbilical cords.

PubMed

Fernando, D M G; Gamage, S M K; Ranmohottige, S; Weerakkody, I; Abeyruwan, H; Parakrama, H

2018-05-01

Mothers of alleged infanticides might claim that umbilical cord broke during precipitate delivery causing injuries detected on baby at autopsy. There is paucity of evidence regarding this possibility. The objective of the study was to determine relationship between tensile strength and diameter or weight per unit length of cord. Diameters and weights per unit length of fresh umbilical cords were determined. Tensile strengths were measured by Hounsfield Testing Machine. Relationship between tensile strength versus cord diameter and weight per unit length were analyzed. Of 122 cords, average tensile strength, diameter and weight per centimeter were 50.4 N, 7.73 mm and 6.87 g respectively. The tensile strengths were directly proportional to diameter. There was no association between tensile strength and weight per centimeter. Measurement of the diameter of cord is important during autopsy to predict tensile strength and thereby to presume whether cord could have broken by the weight of the baby. Copyright © 2018 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.
Particle sizing by weighted measurements of scattered light

NASA Technical Reports Server (NTRS)

Buchele, Donald R.

1988-01-01

A description is given of a measurement method, applicable to a poly-dispersion of particles, in which the intensity of scattered light at any angle is weighted by a factor proportional to that angle. Determination is then made of four angles at which the weighted intensity is four fractions of the maximum intensity. These yield four characteristic diameters, i.e., the diameters of the volume/area mean (D sub 32 the Sauter mean) and the volume/diameter mean (D sub 31); the diameters at cumulative volume fractions of 0.5 (D sub v0.5 the volume median) and 0.75 (D sub v0.75). They also yield the volume dispersion of diameters. Mie scattering computations show that an average diameter less than three micrometers cannot be accurately measured. The results are relatively insensitive to extraneous background light and to the nature of the diameter distribution. Also described is an experimental method of verifying the conclusions by using two microscopic slides coated with polystyrene microspheres to simulate the particles and the background.
Latex Allergy

MedlinePlus

... the material touches the skin. This is called contact dermatitis. Red, itchy bumps or blisters usually appear within ... powdered gloves are used and avoid all direct contact with latex. ... to get a skin rash reaction to latex, latex gloves made without additional ...
34. VIEW OF SUBMARINE ESCAPE TRAINING TANK PRIOR TO ADDITION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. VIEW OF SUBMARINE ESCAPE TRAINING TANK PRIOR TO ADDITION OF BLISTERS IN 1959, LOOKING SOUTHEAST - U.S. Naval Submarine Base, New London Submarine Escape Training Tank, Albacore & Darter Roads, Groton, New London County, CT
An improved technique for the use of zinc-rich coatings

NASA Technical Reports Server (NTRS)

Paton, W. J.

1973-01-01

Blistering and peeling of topcoats used over ethyl silicate, inorganic, zinc-rich protective coatings are virtually eliminated when primer is allowed to cure outdoors for extended period of time and is moistened during process.
37. Photo copy of map, (original in Forest Service Office, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

37. Photo copy of map, (original in Forest Service Office, Elkins, WV, 'Blister Rust Survey Map), 1930. PARSONS NURSERY SITE PLAN - Parsons Nursery, South side of U.S. Route 219, Parsons, Tucker County, WV
40 CFR 264.303 - Monitoring and inspection.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., or blisters; and (2) Soil-based and admixed liners and covers must be inspected for imperfections... layer and minimizes head in the sump. [47 FR 32365, July 26, 1982, as amended at 50 FR 28748, July 15...
40 CFR 264.303 - Monitoring and inspection.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., or blisters; and (2) Soil-based and admixed liners and covers must be inspected for imperfections... layer and minimizes head in the sump. [47 FR 32365, July 26, 1982, as amended at 50 FR 28748, July 15...
40 CFR 264.303 - Monitoring and inspection.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., or blisters; and (2) Soil-based and admixed liners and covers must be inspected for imperfections... layer and minimizes head in the sump. [47 FR 32365, July 26, 1982, as amended at 50 FR 28748, July 15...
40 CFR 264.303 - Monitoring and inspection.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., or blisters; and (2) Soil-based and admixed liners and covers must be inspected for imperfections... layer and minimizes head in the sump. [47 FR 32365, July 26, 1982, as amended at 50 FR 28748, July 15...
40 CFR 264.303 - Monitoring and inspection.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., or blisters; and (2) Soil-based and admixed liners and covers must be inspected for imperfections... layer and minimizes head in the sump. [47 FR 32365, July 26, 1982, as amended at 50 FR 28748, July 15...
Bending Properties of Nickel Electrodes for Nickel-Hydrogen Batteries

NASA Technical Reports Server (NTRS)

Lerch, Brad A.; Wilson, Richard M.; Keller, Dennis; Corner, Ralph

1995-01-01

Recent changes in manufacturing have resulted in nickel-hydrogen batteries that fail prematurely by electrical shorting, This failure is believed to be a result of a blistering problem in the nickel electrodes. In this study the bending properties of nickel electrodes are investigated in an attempt to correlate the bending properties of the electrode with its propensity to blister. Nickel electrodes from three different batches of material were tested in both the as-received and impregnated forms. The effects of specimen curvature and position within the electrode on the bending strength were studied, and within-electrode and batch-to-batch variations were addressed. Two color-imaging techniques were employed to differentiate between the phases within the electrodes. These techniques aided in distinguishing the relative amounts of nickel hyroxide surface loading on each electrode, thereby relating surface loading to bend strength. Bend strength was found to increase with the amount of surface loading.
Initial subjective load carriage injury data collected with interviews and questionnaires.

PubMed

Birrell, Stewart A; Hooper, Robin H

2007-03-01

This study aimed to identify the types, incidence, and causes of any potential load carriage injuries or discomfort as a result of a 2-hour, forced-speed, treadmill march carrying 20 kg. Subjective load carriage data were collected, through both interviews and questionnaires, from relatively inexperienced soldiers after a period of load carriage. Results from the study showed that the upper limb is very susceptible to short-term discomfort, whereas the lower limb is not. The shoulders were rated significantly more uncomfortable then any other region, and blisters were experienced by approximately 60% of participants. Shoulder discomfort commences almost as soon as the load is added and increases steadily with time; however, foot discomfort increases more rapidly once the discomfort materializes. In conclusion, early development of shoulder pain or blisters may be a risk factor for severe pain or noncompletion of a period of prolonged load carriage.
Cilazapril stability in the presence of hydrochlorothiazide in model mixtures and fixed dose combination.

PubMed

Paszun, Sylwia K; Stanisz, Beata J; Gradowska, Agnieszka

2013-01-01

The presented study aimed at the evaluation of hydrochlorothiazide influence on cilazapril stability in model mixture and fixed dose tablet formulation. The degradation of cilazapril in the presence of hydrochlorothiazide took place according to autocatalytic reaction kinetic mechanism, described mathematically by Prout-Tompkins equation. Hydrochlorothiazide coexistence with cilazapril in model mixture and fixed dose tablet without blister package accelerated cilazapril degradation in comparison with degradation of cilazapril substance. Values of reaction induction time shortened, while those of observed reaction rate constant increased. Increasing values of relative humidity and temperature have negative impact on cilazapril stability. Determined semi-logarithmic relationships: In k = f(RH) and Arrhenius ln k = f(1/T) are linear and are cilazapril stability predictive. The blister (OPA/Alu/PVC//Alu) package of fixed dose tablets, constitutes absolute moisture protection and prevent cilazapril--hydrochlorothiazide interaction occurrence.
Toxicological studies on pipemidic acid. V. Effect on diarthrodial joints of experimental animals.

PubMed

Tatsumi, H; Senda, H; Yatera, S; Takemoto, Y; Yamayoshi, M; Ohnishi, K

1978-11-01

Pipemidic acid (PPA) orally given in a dose of 100 mg/kg/day or more was found to cause lame gait in immature beagle dogs of about 3 months old. Their diarthrodial joints were abnormal with increased synovial fluid and blister formation under the outer layer of the articular cartilage. However, such an abnormality was not found in dogs younger than 2 weeks or older than 12 months. The blisters were formed at the joint areas bearing the body weight at a time when PPA was considered to be present there. Nalidixic and piromidic acids, structural analogues of PPA, also caused abnormality similar to PPA. The severity of the arthropathy was slight with piromidic acid as compared with PPA and nalidixic acid. The gait abnormality was almost disappeared spontaneously even if medication was continued. The incidence of the arthropathy was not or rarely observed in any young rats, rabbits and monkeys.
Expression of Selected Integrins and Selectins in Bullous Pemphigoid

PubMed Central

Żebrowska, Agnieszka; Sysa-Jędrzejowska, Anna; Wągrowska-Danilewicz, Małgorzata; Joss-Wichman, Ewa; Erkiert-Polguj, Anna; Waszczykowska, Elżbieta

2007-01-01

Blister development in bullous pemphigoid (BP) results from destruction of hemidesmosomes and basement membrane components within the dermoepidermal junction by autoantibodies. Adhesion molecules can take part in pathogenesis of this disease. The aim of the study was to determine the localization and expression of L- and E-selectins and β1, β3, and β4 integrins by immunohistochemistry in skin lesions of 21 patients with BP, compared with 10 healthy subjects. Expression of L and E selectins and β1, β3 integrins was detected mainly in basal keratinocytes and in inflammatory infiltrates in the dermis, expression of β4 integrin was irregular and was detected mainly in dermal part of the blister, while in the control group only weak and single expression of the examined molecules was detected in basal keratinocytes and endothelium cells. The obtained results reveal the important role of selected selectins and integrins in development of skin lesions in BP. PMID:17515951
Epidermolysis Bullosa Acquitsita

PubMed Central

Gupta, Rishu; Woodley, David T.; Chen, Mei

2011-01-01

EBA is a rare, acquired, chronic subepidermal bullous disease of the skin and mucosa characterized by autoantibodies to type VII collagen structures, a major component of anchoring fibrils, that attach the epidermis onto the dermis. EBA patients have tissue-bound as well as circulating anti-type VII collagen autoantibodies that attack type VII collagen and result in a reduction or perturbation of normally functioning anchoring fibrils. Patients with EBA have skin fragility, blisters, erosions, scars, milia, and nail loss: all features reminiscent of genetic dystrophic epidermolysis bullosa. These anti-type VII collagen antibodies are “pathogenic” because when injected into mice, the mice develop an EBA-like blistering disease. In addition to the classical mechanobullous presentation, EBA also has several other distinct clinical syndromes similar to bullous pemphigoid, Brunsting-Perry pemphigoid, or cicatricial pemphigoid. Although treatment for EBA is often unsatisfactory, some therapeutic success has been achieved with colchicine, dapsone, plasmaphoresis, photopheresis, infliximab, and intravenous immunoglobulin. PMID:22137228
Narrowband UVB-induced lichen planus pemphigoide

PubMed Central

Mandy Chan, Wai Man; See Lee, Joyce Siong; Thiam Theng, Colin Seng; Chua, Sze Hon; Boon Oon, Hazel Hwee

2011-01-01

Lichen planus pemphigoides (LPP) is an autoimmune disease characterised by evolution of subepidermal blisters on normal and lichen planus affected skin. We describe a case of LPP in a 54-year-old Chinese woman. The patient presented with psoriasiform plaques and was diagnosed with guttate psoriasis. Narrowband ultraviolet B (NBUVB) therapy was commenced, and she experienced a generalised eruption of violaceous papules, bullae over the lower limbs, and Wickham's striae over the buccal mucosa. Histology from a plaque revealed interface dermatitis, while a specimen from a blister showed subepidermal bulla. Direct immunofluorescence showed linear deposition of IgG and C3 along the basement membrane. A diagnosis of LPP was made on clinicopathological grounds. This is the first case report of NBUVB alone in unmasking LPP. In this case report, we describe the pathological mechanism of NBUVB in the development of LPP and key features distinguishing LPP from bullous lupus erythematosus, bullous lichen planus, bullous pemphigoid, and psoriasis. PMID:25386295
Micro- and nano-scale damage on the surface of W divertor component during exposure to high heat flux loads with He

NASA Astrophysics Data System (ADS)

Li, C.; Greuner, H.; Zhao, S. X.; Böswirth, B.; Luo, G. N.; Zhou, X.; Jia, Y. Z.; Liu, X.; Liu, W.

2015-11-01

Micro- and nano-scale surface damage on a W divertor component sample exposed to high heat flux loads generated with He atoms has been investigated through SEM, EBSD, AFM and FIB-SEM. The component sample was supplied by the Institute of Plasma Physics, Chinese Academy of Sciences (ASIPP) and AT&M company, China, and the loading experiment was performed in the GLADIS facility at IPP Garching, Germany. Two typical damage structures were observed on the surface: the first one is characterized by obvious blisters and some grooves formed from ruptured blisters, and the other one is a kind of porous structure accompanying with at least ∼25 nm surface material loss. As the grain orientation is further away from <111>, the damage morphology gradually changes from the former structure to the latter. The possible damage mechanism is discussed.

Reynolds Number Effects on Helicopter Rotor Hub Flow

NASA Astrophysics Data System (ADS)

Reich, David; Willits, Steve; Schmitz, Sven

2015-11-01

The 12 inch diameter water tunnel at the Pennsylvania State University Applied Research Laboratory was used with the objective of quantifying effects of Reynolds number scaling on drag and shed wake of model helicopter rotor hub flows. Hub diameter-based Reynolds numbers ranged from 1.06 million to 2.62 million. Measurements included steady and unsteady hub drag, as well as Particle Image Velocimetry. Results include time-averaged, phase-averaged, and spectral analysis of the drag and wake flow-field. A strong dependence of steady and unsteady drag on Reynolds number was noted, alluding to the importance of adequate Reynolds scaling for model helicopter rotor hubs that exhibit interaction between various bluff bodies.
A Similarity Criterion for Supersonic Flow Past a Cylinder with a Frontal High-Porosity Cellular Insert

NASA Astrophysics Data System (ADS)

Mironov, S. G.; Poplavskaya, T. V.; Kirilovskiy, S. V.; Maslov, A. A.

2018-03-01

We have experimentally and numerically studied the influence of the ratio of the diameter of a cylinder with a frontal gas-permeable porous insert made of nickel sponge to the average pore diameter in the insert on the aerodynamic drag of this model body in supersonic airflow ( M ∞ = 4.85, 7, and 21). The analytical dependence of the normalized drag coefficient on a parameter involving the Mach number and the ratio of cylinder radius to average pore radius in the insert is obtained. It is suggested to use this parameter as a similarity criterion in the problem of supersonic airflow past a cylinder with a frontal high-porosity cellular insert.
Network of listed companies based on common shareholders and the prediction of market volatility

NASA Astrophysics Data System (ADS)

Li, Jie; Ren, Da; Feng, Xu; Zhang, Yongjie

2016-11-01

In this paper, we build a network of listed companies in the Chinese stock market based on common shareholding data from 2003 to 2013. We analyze the evolution of topological characteristics of the network (e.g., average degree, diameter, average path length and clustering coefficient) with respect to the time sequence. Additionally, we consider the economic implications of topological characteristic changes on market volatility and use them to make future predictions. Our study finds that the network diameter significantly predicts volatility. After adding control variables used in traditional financial studies (volume, turnover and previous volatility), network topology still significantly influences volatility and improves the predictive ability of the model.
Size quantization patterns in self-assembled InAs/GaAs quantum dots

NASA Astrophysics Data System (ADS)

Colocci, M.; Bogani, F.; Carraresi, L.; Mattolini, R.; Bosacchi, A.; Franchi, S.; Frigeri, P.; Taddei, S.; Rosa-Clot, M.

1997-07-01

Molecular beam epitaxy has been used for growing self-assembled InAs quantum dots. A continuous variation of the InAs average coverage across the sample has been obtained by properly aligning the (001) GaAs substrate with respect to the molecular beam. Excitation of a large number of dots (laser spot diameter ≈ 100 μm) results in structured photoluminescence spectra; a clear quantization of the dot sizes is deduced from the distinct luminescence bands separated in energy by an average spacing of 20-30 meV. We ascribe the individual bands of the photoluminescence spectrum after low excitation to families of dots with roughly the same diameter and heights differing by one monolayer.
Blisters and Loss of Epidermis in Patients With Lupus Erythematosus

PubMed Central

Merklen-Djafri, Carine; Bessis, Didier; Frances, Camille; Poulalhon, Nicolas; Debarbieux, Sébastien; Cordel, Nadège; Lipsker, Dan

2015-01-01

Abstract The nosology of bullous lesions or equivalents (vesicles, erosions, and crusts) in patients with lupus erythematosus (LE) is rarely addressed. The primary aim of this study was to draw up a precise phenotypic inventory of such skin lesions; the secondary objective was to assess a potential relationship between the different types of loss of epidermis and extracutaneous lupus manifestations. We conducted a retrospective multicenter study including 22 patients with definite LE and bullous lesions or equivalents. All biopsies were reviewed. Patients were recruited in the dermatology departments of 6 centers. Patients were included if they met the diagnosis of systemic LE according to American College of Rheumatology and/or Systemic Lupus International Collaborating Clinics criteria or diagnosis of cutaneous LE based on classic clinical criteria and/or histological ascertainment of LE. Patients were recruited through clinician's memory and photographic collections. Three clinico-pathological patterns could be individualized. First, toxic epidermal necrolysis (TEN)-like, sheet-like, skin detachment; sun-exposure, mild mucosal involvement, and dermal mucin deposition allow differential diagnosis with classical Lyell syndrome. Second, vesiculo-bullae and/or crusting occurring on typical lesions of subacute cutaneous lupus erythematosus or chronic cutaneous lupus erythematosus. Third, tense vesicles and/or blisters with an underlying neutrophilic dermatosis and a usual response to dapsone. A careful analysis of 22 LE patients with epidermal detachment reveals 2 main pathomechanisms: a classic LE interface dermatitis, which can be hyperacute and lead to TEN-like skin detachment; and a neutrophilic dermatosis, with tense vesicles and/or blisters, including classic bullous LE. PMID:26579826
Lemons in the Arizona Sunshine: The Effects of Furocoumarins Leading to Phytophotodermatitis and Burn-like Injuries.

PubMed

Matthews, Marc R; VanderVelde, Joel C; Caruso, Daniel M; Foster, Kevin N

2017-12-01

Phytophototoxic dermatitis is a strong phototoxic reaction to ultraviolet A (UV-A) radiation exposure after cutaneous contact with citrus fruit containing furocoumarins, leading to skin injury. At the Arizona Burn Center (Phoenix, AZ), the majority of these injuries are managed in the outpatient setting. The authors present a pediatric admission for burn-like injuries following prolonged cutaneous exposure to lemons while playing in the Arizona sunshine. A 7-year-old girl playing in her backyard squeezed lemon juice onto her skin while in the hot Arizona sunshine; within 24 hours, the child experienced pain, erythema, and blistering to multiple areas of her skin. She was admitted to the authors' burn center for wound care and pain control. She had scattered first-degree and second-degree burn-like lesions to her face, neck, and chest as well as bilateral forearms, hands, lower extremities, and feet. After blister debridement, appropriate dressing care, and pain medication, the patient was discharged home after 4 days of hospitalization with appropriate clinical follow-up. Burn-like lesions caused by furocoumarins after cutaneous absorption and UV-A exposure are known clinical entities in Arizona. The sequential progression from erythema to blisters equivalent to second-degree burn-like lesions to cutaneous hyperpigmentation is a well-described clinical triad. Meticulous wound care and pain control for the treatment of these burn-like lesions are essential as is the need for the wound care specialist to be well versed on this topic to quickly identify the etiology of the injury, thereby avoiding misdiagnosing the patient with nonaccidental traumatic injuries.
Investigation of Ag buffered Ni and Ni-Cr alloys as substrates for the preparation of bismuth superconducting tapes

NASA Astrophysics Data System (ADS)

Régnier, P.; Bifulco-Michon, C.; Poissonnet, S.; Martin, H.; Bonnaillie, P.; Giunchi, G.; Legendre, F.

2002-10-01

We review and comment on the various requirements that a metallic substrate has to meet to be a good candidate for the fabrication of electrodeposited BSCCO superconducting tapes. We conclude that, in the present state of the art, no metallic substrate is really ideal. Hence we have investigated in detail the use of silver-buffered nickel-based alloys that seem to be a viable alternative to pure silver tape, which is more expensive and less resistant to high temperature. The major difficulty encountered was the occurrence of holes and blisters induced in the silver layers by the oxidation of the nickel underlayer during the heat treatments performed at high temperature in open air, which according to our procedure are required to synthesize high-temperature superconducting tapes. It was found that the liquid phases, transiently present in the process during the synthesis of the precursor phases, infiltrate between the Ag layer and the substrate through these holes and strongly react with the substrate transferring the poisoned element to the superconducting film greatly reducing its superconducting properties. Hence, several routes have been explored to try and suppress hole formation. It was found that pre-oxidizing the substrate at 880 °C for 1 h in open air sufficiently lowers the hole and blister densities to allow us to synthesize good Bi-2212 tapes on pure nickel, but not on Ni80-Cr20 alloys. A much more interesting solution seems to be to pre-anneal the substrate in a hydrogenous atmosphere which permits us to remove blisters and holes.
High-flow bypass and wrap-clipping for ruptured blood blister-like aneurysm of the internal carotid artery using intraoperative monitoring of cerebral hemodynamics

PubMed Central

Kubo, Yoshitaka; Koji, Takahiro; Yoshida, Kenji; Saito, Hideo; Ogawa, Akira; Ogasawara, Kuniaki

2015-01-01

Aneurysms at non-branching sites in the supraclinoid internal carotid artery (ICA) can be classified as “blood blister-like aneurysms” (BBAs), which have blood blister-like configurations and fragile walls. While surgical treatment for the BBA in the acute stage is recommended, the optimal surgical procedure remains controversial. In the study reported here, we describe the case of a 37-year-old woman with a ruptured BBA in the ophthalmic segment of the right ICA who underwent wrap-clipping with external carotid artery–internal carotid artery bypass by intraoperative estimation of the measurement of cortical cerebral blood flow (CoBF) using a thermal diffusion flow probe. Trapping of the ICA in the acute stage of subarachnoid hemorrhage may result in ischemic complications secondary to hemodynamic hypoperfusion or occlusion of the perforating artery, and/or delayed vasospasm, even with concomitant bypass surgery. We believe that it is important to perform scheduled external carotid artery–internal carotid artery bypass before trapping of the ICA in patients with a ruptured BBA in the acute stage of subarachnoid hemorrhage and to perform wrap-clipping rather than trapping. This would provide much more CoBF if a reduction of CoBF occurs after trapping occlusion of the ICA including a ruptured BBA according to intraoperative CoBF monitoring. As far as we are aware, the case reported here is the first report on high-flow bypass and wrap-clipping for a ruptured BBA of the ICA using intraoperative monitoring of cerebral hemodynamics. PMID:26082641
[Spatial structural characteristics of natural Populus davidiana - Betula platyphylla secondary forest].

PubMed

Shao, Fang-Li; Yu, Xin-Xiao; Song, Si-Ming; Zhao, Yang

2011-11-01

This paper analyzed the spatial structural characteristics of natural Populus davidiana - Betula platyphylla secondary forest in a 4 hm2 plot of Mulan Paddock, based on the diameter distribution and the spatial structure parameters mingling degree, neighborhood comparison, and angle index. In the forest, the diameter distribution of the stands presented as an inverse 'J' curve, the average mingling degree was 0.4, with the individuals at weak and zero mingling degree reached 51.6%, and the average mingling degree of P. davidiana and B. platyphylla was 0.25 and 0.39, respectively. The neighborhood comparison based on the diameter at breast height (DBH) and tree height was almost the same, suggesting that the P. davidiana and B. platyphylla were in the transition state from subdominant to middle. The horizontal distribution pattern had a close relation to the minimum measured DBH, being clustered when the DBH was > or = 1 cm and < 6 cm, and random when the DBH was > or = 6 cm.
Morphology control of PLA microfibers and spheres via melt electrospinning

NASA Astrophysics Data System (ADS)

Yu, Shu-Xin; Zheng, Jie; Yan, Xu; Wang, Xiao-Xiong; Nie, Guang-Di; Tan, Ye-Qiang; Zhang, Jun; Sui, Kun-Yan; Long, Yun-Ze

2018-04-01

In conventional solution electrospinning, the morphologies (e.g., spheres, beaded fibers, and fibers) of electrospun products can be controlled by solution concentration. Here, we report that the morphologies and structures of polylactic acid (PLA) via melt electrospinning also can be adjusted from microfibers to microspheres by simply increasing the spinning temperature. It was found that with temperature increasing from 200 °C to 240 °C, the average diameter of melt-electrospun PLA fibers decreased from 58.46 to 2.96 μm. Then, beaded fibers and microspheres about 14.5 μm in diameter were collected when the spinning temperature was increased to 250 °C and 260 °C. In addition, we also found that the average PLA fiber diameter decreased with increasing the applied spinning voltage, and increased with the increase of spinning distance. To explain the formation mechanism of different PLA microstructures, rheological property and infrared spectra of PLA under different spinning temperatures were also tested.
Ultrafine Ti4+ doped α-Fe2O3 nanorod array photoanodes with high charge separation efficiency for solar water splitting

NASA Astrophysics Data System (ADS)

Liu, Yilin; Liu, Jie; Luo, Wenjun; Wen, Xin; Liu, Xiaokang; Zou, Zhigang; Huang, Wei

2017-06-01

Hematite (α-Fe2O3) is a promising photoanode material for solar water splitting due to its suitable band gap, earth-abundance, excellent stability and non-toxicity. However, a short hole diffusion length limits its performance. A nanorod array structure can shorten hole transfer distance to photoelectrode/electrolyte interface and decrease recombination of photo-generated carriers. However, average diameters of all previously reported nanorods are over 50 nm, thus being too thick for holes to transfer to the interface. It is still a big challenge to prepare a Fe2O3 nanorod array photoelectrode with finer diameter. In this study, we prepare an ultrafine α-Fe2O3 nanorod array film with average diameter about 25 nm by calcining γ-FeOOH for the first time. The ultrafine nanorod array photoanode indicates much higher carrier separation efficiency and performance than a conventional nanorod array film.
Ring-diameter Ratios for Multi-ring Basins Average 2.0(0.5)D

NASA Technical Reports Server (NTRS)

Pike, R. J.; Spudis, P. D.

1985-01-01

The spacing of the concentric rings of planetary impact basins was studied. It is shown that a radial increment of x (sup 0.5) D, where x is about 2.0 and D = ring diameter, separates both (1) adjacent least-squares groups of rings and arcs of multi-ring basins on Mars, Mercury, and the Moon; and (2) adjacent rings of individual basins on the three planets. Statistics for ratios of ring diameters are presented, the first and most-applied parameter of ring spacing. It is found that ratios excluding rings flanking the main ring also have a mean spacing increment of about 2.0. Ratios including such rings, as for the least-squares groups, and (1) above, have a larger increment, averaging 2.1. The F-test indicates, that these spacings of basin ring locations, and mode of ring formation are controlled by the mechanics of the impact event itself, rather than by crustal properties.
EPA Science Matters Newsletter: Chemical Warfare Agent Analytical Standards Facilitate Lab Testing (Published November 2013)

EPA Pesticide Factsheets

Learn about the EPA chemists' efforts to develop methods for detecting extremely low concentrations of nerve agents, such as sarin, VX, soman and cyclohexyl sarin, and the blister agent sulfur mustard.
78 FR 45911 - Foreign-Trade Zone (FTZ) 38-Spartanburg County, South Carolina, Notification of Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-30

... chargers; magnets; magnetic chucks; lead-acid, power pack, NiMH and lithium ion batteries; SA battery packs...-bags; battery caps; blister packs; shrink-heat tubing; plastic handles and knobs; O- rings; seals...
Intense pulsed light annealing of copper zinc tin sulfide nanocrystal coatings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Bryce A.; Smeaton, Michelle A.; Holgate, Collin S.

2016-09-15

A promising method for forming the absorber layer in copper zinc tin sulfide [Cu{sub 2}ZnSnS{sub 4} (CZTS)] thin film solar cells is thermal annealing of coatings cast from dispersions of CZTS nanocrystals. Intense pulsed light (IPL) annealing utilizing xenon flash lamps is a potential high-throughput, low-cost, roll-to-roll manufacturing compatible alternative to thermal annealing in conventional furnaces. The authors studied the effects of flash energy density (3.9–11.6 J/cm{sup 2}) and number of flashes (1–400) during IPL annealing on the microstructure of CZTS nanocrystal coatings cast on molybdenum-coated soda lime glass substrates (Mo-coated SLG). The annealed coatings exhibited cracks with two distinct linearmore » crack densities, 0.01 and 0.2 μm{sup −1}, depending on the flash intensity and total number of flashes. Low density cracking (0.01 μm{sup −1}, ∼1 crack per 100 μm) is caused by decomposition of CZTS at the Mo-coating interface. Vapor decomposition products at the interface cause blisters as they escape the coating. Residual decomposition products within the blisters were imaged using confocal Raman spectroscopy. In support of this hypothesis, replacing the Mo-coated SLG substrate with quartz eliminated blistering and low-density cracking. High density cracking is caused by rapid thermal expansion and contraction of the coating constricted on the substrate as it is heated and cooled during IPL annealing. Finite element modeling showed that CZTS coatings on low thermal diffusivity materials (i.e., SLG) underwent significant differential heating with respect to the substrate with rapid rises and falls of the coating temperature as the flash is turned on and off, possibly causing a build-up of tensile stress within the coating prompting cracking. Use of a high thermal diffusivity substrate, such as a molybdenum foil (Mo foil), reduces this differential heating and eliminates the high-density cracking. IPL annealing in presence of sulfur vapor prevented both low- and high-density cracking as well as blistering. However, grain growth was limited even after annealing with 400 flashes. This lack of grain growth is attributed to a difficulty of maintaining high sulfur vapor pressure and absence of alkali metal impurities when Mo foil substrates are used.« less
Device-less patent foramen ovale closure by radiofrequency thermal energy.

PubMed

Walpoth, Nazan B; Habermacher, Kathrin; Moarof, Igal; Watson, Sandy; Wahl, Andreas; Windecker, Stephan; Schönenberger, Christa; Meier, Bernhard

2008-02-23

The goal of this study was to assess the feasibility, safety and success of a system which uses radiofrequency energy (RFE) rather than a device for percutaneous closure of patent foramen ovale (PFO). Sixteen patients (10 men, 6 women, mean age 50 years) were included in the study. All of them had a proven PFO with documented right-to-left shunt (RLS) after Valsalva manoeuvre (VM) during transoesophageal echocardiography (TEE). The patients had an average PFO diameter of 6 +/- 2 mm at TEE and an average of 23 +/- 4 microembolic signals (MES) in power M-mode transcranial Doppler sonography (pm-TCD), measured over the middle cerebral artery. An atrial septal aneurysm (ASA) was present in 7 patients (44%). Balloon measurement, performed in all patients, revealed a stretched PFO diameter of 8 +/- 3 mm. In 2 patients (stretched diameter 11 and 14 mm respectively, both with ASA >10 mm), radiofrequency was not applied (PFO too large) and the PFO was closed with an Amplatzer PFO occluder instead. A 6-month follow-up TEE was performed in all patients. There were no serious adverse events during the procedure or at follow-up (12 months average). TEE 6 months after the first RFE procedure showed complete closure of the PFO in 50% of the patients (7/14). Closure appeared to be influenced by PFO diameter, complete closure being achieved in 89% (7/8) with a balloon-stretched diameter < or =7 mm but in none of the patients >7 mm. Only one of the complete closure patients had an ASA. Of the remainder, 4 (29%) had an ASA. Although the PFO was not completely closed in this group, some reduction in the diameter of the PFO and in MES was documented by TEE and pm-TCD with VM. Five of the 7 residual shunt patients received an Amplatzer PFO occluder. Except for one patient with a minimal residual shunt, all showed complete closure of PFO at 6-month follow-up TEE and pm-TCD with VM. The other two refused a closure device. The results confirm that radiofrequency closure of the PFO is safe albeit less efficacious and more complex than device closure. The technique in its current state should not be attempted in patients with a balloon-stretched PFO diameter >7 mm and an ASA.
Influence of cervical preflaring on apical file size determination.

PubMed

Pecora, J D; Capelli, A; Guerisoli, D M Z; Spanó, J C E; Estrela, C

2005-07-01

To investigate the influence of cervical preflaring with different instruments (Gates-Glidden drills, Quantec Flare series instruments and LA Axxess burs) on the first file that binds at working length (WL) in maxillary central incisors. Forty human maxillary central incisors with complete root formation were used. After standard access cavities, a size 06 K-file was inserted into each canal until the apical foramen was reached. The WL was set 1 mm short of the apical foramen. Group 1 received the initial apical instrument without previous preflaring of the cervical and middle thirds of the root canal. Group 2 had the cervical and middle portion of the root canals enlarged with Gates-Glidden drills sizes 90, 110 and 130. Group 3 had the cervical and middle thirds of the root canals enlarged with nickel-titanium Quantec Flare series instruments. Titanium-nitrite treated, stainless steel LA Axxess burs were used for preflaring the cervical and middle portions of root canals from group 4. Each canal was sized using manual K-files, starting with size 08 files with passive movements until the WL was reached. File sizes were increased until a binding sensation was felt at the WL, and the instrument size was recorded for each tooth. The apical region was then observed under a stereoscopic magnifier, images were recorded digitally and the differences between root canal and maximum file diameters were evaluated for each sample. Significant differences were found between experimental groups regarding anatomical diameter at the WL and the first file to bind in the canal (P < 0.01, 95% confidence interval). The major discrepancy was found when no preflaring was performed (0.151 mm average). The LA Axxess burs produced the smallest differences between anatomical diameter and first file to bind (0.016 mm average). Gates-Glidden drills and Flare instruments were ranked in an intermediary position, with no statistically significant differences between them (0.093 mm average). The instrument binding technique for determining anatomical diameter at WL is not precise. Preflaring of the cervical and middle thirds of the root canal improved anatomical diameter determination; the instrument used for preflaring played a major role in determining the anatomical diameter at the WL. Canals preflared with LA Axxess burs created a more accurate relationship between file size and anatomical diameter.
Diameter-growth model across shortleaf pine range using regression tree analysis

Treesearch

Daniel Yaussy; Louis Iverson; Anantha Prasad

1999-01-01

Diameter growth of a tree in most gap-phase models is limited by light, nutrients, moisture, and temperature. Growing-season temperature is represented by growing degree days (gdd), which is the sum of the average daily temperatures above a baseline temperature. Gap-phase models determine the north-south range of a species by the gdd limits at the north and south...
Twenty-year growth of thinned and unthinned ponderosa pine in the Methow Valley of northern Washington.

Treesearch

James W. Barrett

1981-01-01

Diameter, height and volume growth, and yield of thinned and unthinned plots are given for a suppressed, 47-year-old stand of ponderosa pine (Pinus ponderosa Dougl. ex Laws.) in the Methow Valley of northern Washington that averaged about 3 inches in diameter and 23 feet tall before thinning. Considerations are discussed for choosing tree spacing...
Cottonwood Plantation Growth Through 20 Years

Treesearch

Roger M. Krinard; Robert L. Johnson

1984-01-01

At age 20 survival of unthinned cottonwood (Populusdeltoides Bartr. ex Marsh.) planted on medium-textured soil at spacings of 4 by 9, 8 by 9, 12 by 12, and 16 by 18 feet was 10, 17, 30, and 62 percent, and average diameters were 10.6, 11.8, 12.6, and 13.7 inches, respectively. Depending on spacing and diameter threshold, -cubic volume mean annual increment peaked at...

Some links on this page may take you to non-federal websites. Their policies may differ from this site.