Temporal dynamics of CO2 fluxes and profiles over a Central European city

NASA Astrophysics Data System (ADS)

Vogt, R.; Christen, A.; Rotach, M. W.; Roth, M.; Satyanarayana, A. N. V.

2006-02-01

In Summer 2002 eddy covariance flux measurements of CO2 were performed over a dense urban surface. The month-long measurements were carried out in the framework of the Basel Urban Boundary Layer Experiment (BUBBLE). Two Li7500 open path analysers were installed at z/z H = 1.0 and 2.2 above a street canyon with z H the average building height of 14.6 m and z the height above street level. Additionally, profiles of CO2 concentration were sampled at 10 heights from street level up to 2 z H . The minimum and maximum of the average diurnal course of CO2 concentration at 2 z H were 362 and 423 ppmv in late afternoon and early morning, respectively. Daytime CO2 concentrations were not correlated to local sources, e.g. the minimum occurred together with the maximum in traffic load. During night-time CO2 is in general accumulated, except when inversion development is suppressed by frontal passages. CO2 concentrations were always decreasing with height and correspondingly, the fluxes on average always directed upward. At z/z H = 2.2 low values of about 3 µmol m-2 s-1 were measured during the second half of the night. During daytime average values reached up to 14 µmol m-2 s-1. The CO2 fluxes are well correlated with the traffic load, with their maxima occurring together in late afternoon. Daytime minimum CO2 concentrations fell below regional background values. Besides vertical mixing and entrainment, it is suggested that this is also due to advection of rural air with reduced CO2 concentration. Comparison with other urban observations shows a large range of differences among urban sites in terms of both CO2 fluxes and concentrations.

Mean wind speed below building height in residential neighborhoods with different tree densities

Treesearch

G.M. Heisler

1990-01-01

There is little available knowledge of the absolute or relative effects of trees and buildings on wind at or below building height in residential neighborhoods. In this study, mean wind speed was measured at a height of 6.6 ft (2 m) in neighborhoods of single-family houses. BuIlding densities ranged between 6% and 12% of the land ares, and tree-cover densities were...

The Budget of Turbulent Kinetic Energy in the Urban Roughness Sublayer

NASA Astrophysics Data System (ADS)

Christen, Andreas; Rotach, Mathias W.; Vogt, Roland

2009-05-01

Full-scale observations from two urban sites in Basel, Switzerland were analysed to identify the magnitude of different processes that create, relocate, and dissipate turbulent kinetic energy (TKE) in the urban atmosphere. Two towers equipped with a profile of six ultrasonic anemometers each sampled the flow in the urban roughness sublayer, i.e. from street canyon base up to roughly 2.5 times the mean building height. This observational study suggests a conceptual division of the urban roughness sublayer into three layers: (1) the layer above the highest roofs, where local buoyancy production and local shear production of TKE are counterbalanced by local viscous dissipation rate and scaled turbulence statistics are close to to surface-layer values; (2) the layer around mean building height with a distinct inflexional mean wind profile, a strong shear and wake production of TKE, a more efficient turbulent exchange of momentum, and a notable export of TKE by transport processes; (3) the lower street canyon with imported TKE by transport processes and negligible local production. Averaged integral velocity variances vary significantly with height in the urban roughness sublayer and reflect the driving processes that create or relocate TKE at a particular height. The observed profiles of the terms of the TKE budget and the velocity variances show many similarities to observations within and above vegetation canopies.

Simulations of the impacts of building height layout on air quality in natural-ventilated rooms around street canyons.

PubMed

Yang, Fang; Zhong, Ke; Chen, Yonghang; Kang, Yanming

2017-10-01

Numerical simulations were conducted to investigate the effects of building height ratio (i.e., HR, the height ratio of the upstream building to the downstream building) on the air quality in buildings beside street canyons, and both regular and staggered canyons were considered for the simulations. The results show that the building height ratio affects not only the ventilation fluxes of the rooms in the downstream building but also the pollutant concentrations around the building. The parameter, outdoor effective source intensity of a room, is then proposed to calculate the amount of vehicular pollutants that enters into building rooms. Smaller value of this parameter indicates less pollutant enters the room. The numerical results reveal that HRs from 2/7 to 7/2 are the favorable height ratios for the regular canyons, as they obtain smaller values than the other cases. While HR values of 5/7, 7/7, and 7/5 are appropriate for staggered canyons. In addition, in terms of improving indoor air quality by natural ventilation, the staggered canyons with favorable HR are better than those of the regular canyons.

Mitigating shear lag in tall buildings

NASA Astrophysics Data System (ADS)

Gaur, Himanshu; Goliya, Ravindra K.

2015-09-01

As the height of building increases, effect of shear lag also becomes considerable in the design of high-rise buildings. In this paper, shear lag effect in tall buildings of heights, i.e., 120, 96, 72, 48 and 36 stories of which aspect ratio ranges from 3 to 10 is studied. Tube-in-tube structural system with façade bracing is used for designing the building of height 120 story. It is found that bracing system considerably reduces the shear lag effect and hence increases the building stiffness to withstand lateral loads. Different geometric patterns of bracing system are considered. The best effective geometric configuration of bracing system is concluded in this study. Lateral force, as wind load is applied on the buildings as it is the most dominating lateral force for such heights. Wind load is set as per Indian standard code of practice IS 875 Part-3. For analysis purpose SAP 2000 software program is used.

[Effect of greenbelt on pollutant dispersion in street canyon].

PubMed

Xu, Wei-Jia; Xing, Hong; Yu, Zhi

2012-02-01

The effect feature of greenbelt on flow field and pollutant dispersion in urban street canyon was researched. The greenbelt was assumed as uniform porous media and its aerodynamics property defined by the pressure loss coefficient. Subsequently, the pollutant dispersion in the street canyon of which there was greenbelt in the middle was simulated with the steady-state standard kappa-epsilon turbulence model and species transport equation. The simulated results agreed well with the wind-tunnel data. Compared with the treeless case, it finds that the street canyon contain a clockwise vortex, the pollutant concentration of the leeward was several times than the windward and the growth rate of pollutant concentration was 46.0%. The further simulation for the impact of tree crown position on the airflow and pollutant dispersion finds that the height of major vortex center in the street canyon increases with the height of tree crown and gradually closes the top of windward building This causes that the average wind speed in the street canyon decreases. Especially when the top of tree crown over the roof and hinder the air flow above the street canyon, the average pollutant concentration increases with the height of tree crown rapidly.

3D Concrete Printing Concept Could Solve Tall-Wind Dilemma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cotrell, Jason; Jenne, Scott; Butterfield, Sandy

When building a wind turbine, you want to make it as tall as possible to capture stronger, faster winds aloft. But taller tower bases become too large to be transported over the road—a constraint that has kept average U.S. wind turbine heights at 80 meters for the last 10 years. A Lab-Corps project undertaken by the National Renewable Energy Laboratory has found a potential solution: automated concrete manufacturing.

Aerodynamic Parameters of a UK City Derived from Morphological Data

NASA Astrophysics Data System (ADS)

Millward-Hopkins, J. T.; Tomlin, A. S.; Ma, L.; Ingham, D. B.; Pourkashanian, M.

2013-03-01

Detailed three-dimensional building data and a morphometric model are used to estimate the aerodynamic roughness length z 0 and displacement height d over a major UK city (Leeds). Firstly, using an adaptive grid, the city is divided into neighbourhood regions that are each of a relatively consistent geometry throughout. Secondly, for each neighbourhood, a number of geometric parameters are calculated. Finally, these are used as input into a morphometric model that considers the influence of height variability to predict aerodynamic roughness length and displacement height. Predictions are compared with estimations made using standard tables of aerodynamic parameters. The comparison suggests that the accuracy of plan-area-density based tables is likely to be limited, and that height-based tables of aerodynamic parameters may be more accurate for UK cities. The displacement heights in the standard tables are shown to be lower than the current predictions. The importance of geometric details in determining z 0 and d is then explored. Height variability is observed to greatly increase the predicted values. However, building footprint shape only has a significant influence upon the predictions when height variability is not considered. Finally, we develop simple relations to quantify the influence of height variation upon predicted z 0 and d via the standard deviation of building heights. The difference in these predictions compared to the more complex approach highlights the importance of considering the specific shape of the building-height distributions. Collectively, these results suggest that to accurately predict aerodynamic parameters of real urban areas, height variability must be considered in detail, but it may be acceptable to make simple assumptions about building layout and footprint shape.

3D Concrete Printing Concept Could Solve Tall-Wind Dilemma

ScienceCinema

Cotrell, Jason; Jenne, Scott; Butterfield, Sandy

2018-06-12

When building a wind turbine, you want to make it as tall as possible to capture stronger, faster winds aloft. But taller tower bases become too large to be transported over the road—a constraint that has kept average U.S. wind turbine heights at 80 meters for the last 10 years. A Lab-Corps project undertaken by the National Renewable Energy Laboratory has found a potential solution: automated concrete manufacturing.

A spatiotemporal multi-hazard exposure assessment based on property data

NASA Astrophysics Data System (ADS)

Fuchs, S.; Keiler, M.; Zischg, A.

2015-09-01

The paper presents a nation-wide spatially explicit object-based assessment of buildings and citizens exposed to natural hazards in Austria, including river flooding, torrential flooding, and snow avalanches. The assessment was based on two different data sets, (a) hazard information providing input to the exposure of elements at risk, and (b) information on the building stock combined from different spatial data available on the national level. Hazard information was compiled from two different sources. For torrential flooding and snow avalanches available local-scale hazard maps were used, and for river flooding the results of the countrywide flood modelling eHORA were available. Information on the building stock contained information on the location and size of each building, as well as on the building category and the construction period. Additional information related to the individual floors, such as their height and net area, main purpose and configuration, was included for each property. Moreover, this data set has an interface to the population register and allowed, therefore, for retrieving the number of primary residents for each building. With the exception of sacral buildings, an economic module was used to compute the monetary value of buildings using (a) the information of the building register such as building type, number of storeys and utilisation, and (b) regionally averaged construction costs. It is shown that the repeatedly stated assumption of increasing exposure due to continued population growth and related increase in assets has to be carefully evaluated by the local development of building stock. While some regions have shown a clearly above-average increase in assets, other regions were characterised by a below-average development. This mirrors the topography of the country, but also the different economic activities. While hotels and hostels are extraordinarily prone to torrential flooding, commercial buildings as well as buildings used for recreational purposes are considerably exposed to river flooding. Residential buildings have shown an average exposure, compared to the number of buildings of this type in the overall building stock. In sum, around 5 % of all buildings are exposed to torrential flooding, and around 9 % to river flooding, with around 1 % of the buildings stock being multi-exposed. The temporal assessment of exposure has shown considerable differences in the dynamics of exposure to different hazard categories in comparison to the overall property stock. In conclusion, the presented object-based assessment is an important and suitable tool for nation-wide exposure assessment and may be used in operational risk management.

Сontamination of urban soils with heavy metals in Moscow as affected by building development.

PubMed

Kosheleva, Natalia E; Vlasov, Dmitry V; Korlyakov, Ilya D; Kasimov, Nikolay S

2018-09-15

Building development in cities creates a geochemical heterogeneity via redistributing the atmospheric fluxes of pollutants and forming sedimentation zones in urban soils and other depositing media. However, the influence of buildings on the urban environment pollution is poorly understood. The aim of this study is to evaluate the barrier functions of urban development by means of a joint analysis of the contents of heavy metals and metalloids in the upper horizon of urban soils, their physicochemical properties, and the parameters of the buildings. The soil-geochemical survey was performed in the residential area of the Moscow's Eastern Administrative District (Russia). The parameters of the buildings near sampling points were determined via processing data from the OpenStreetMap database, 2GIS databases and GeoEye-1 satellite image. A high level of soil contamination with Cd, W, Bi, Zn, As, Cr, Sb, Pb, Cu was revealed, depending on building parameters. A protective function of the buildings for yards is manifested in the decreasing concentrations of As, Cd, Co, Cr, Mo, Ni, Pb, Sb, Sn, W by 1.2-3 times at distances of <23-36 m from the buildings with their total area ≥660 m 2 and the height ≥7.5-21 m. An opposite effect which enhances concentrations of Bi, Cd, Co, Cr, Cu, Mo, Pb, Sb, Sn, W, Zn by 1.2-1.9 times is seen in "well-shaped" yards acting as traps under similar distances and heights, but at their average area ≥118-323 m 2 , and total area ≥323-1300 m 2 . The impact of these two building patterns on the soil contamination is only seen for certain directions of atmospheric flows. Buildings located in the northwestern sector relative to the sampling point protect the latter from the aerial pollution. Copyright © 2018 Elsevier B.V. All rights reserved.

The Impact of Roadside Barriers and Buildings on Near Road Concentrations of Vehicle Emissions

NASA Astrophysics Data System (ADS)

Schulte, Nico

Exposure to elevated concentrations of vehicle emitted pollutants is associated with negative health effects. Elevated concentrations are typically found within several hundred meters of high traffic roads, where atmospheric dispersion has not sufficiently diluted pollutants. Tall buildings next to roads reduce dispersion, thereby creating pollutant hot spots and increasing exposure to vehicle emissions for city residents. Roadside barriers enhance dispersion of roadway emissions and thus can be used to mitigate elevated concentrations next to large roads. The work in this thesis develops semi-empirical dispersion models that are useful for estimating near road concentrations of vehicle emissions when there are buildings or barriers next to the road. Dispersion models that account for the effect of near road barriers on concentrations are developed and evaluated with data from a wind tunnel and a field tracer study. The model evaluation shows that the primary effect of roadside barriers is enhancement of the vertical mixing by an amount proportional to the barrier height. Additionally, turbulence is enhanced in the barrier's wake, resulting in more rapid growth of the pollutant plume. The models perform well during neutral and stable atmospheric conditions. During unstable conditions the models overestimate concentrations. A model that accounts for reduction of the mean wind speed in the barrier wake is unbiased for all stabilities. Models of the impact of tall buildings next to the road on near road concentrations of vehicle emissions are developed. The models are evaluated with data from field measurements conducted in Los Angeles and Riverside counties, CA, and with data from an urban area in Hannover, Germany. The study specifically investigates dispersion in cities with significant building height variability. Model evaluation shows that vertical turbulent transport dominates dispersion in cities. The primary variables governing near road concentrations of vehicle emissions in cities are the ratio of area weighted building height to street width and the vertical averaged standard deviation of vertical velocity fluctuations. The model informs design of transit oriented developments, dense residential areas located in close proximity to transportation infrastructure, which are used to reduce pollution and greenhouse gas emissions due to transportation.

Global effects of income and income inequality on adult height and sexual dimorphism in height.

PubMed

Bogin, Barry; Scheffler, Christiane; Hermanussen, Michael

2017-03-01

Average adult height of a population is considered a biomarker of the quality of the health environment and economic conditions. The causal relationships between height and income inequality are not well understood. We analyze data from 169 countries for national average heights of men and women and national-level economic factors to test two hypotheses: (1) income inequality has a greater association with average adult height than does absolute income; and (2) neither income nor income inequality has an effect on sexual dimorphism in height. Average height data come from the NCD-RisC health risk factor collaboration. Economic indicators are derived from the World Bank data archive and include gross domestic product (GDP), Gross National Income per capita adjusted for personal purchasing power (GNI_PPP), and income equality assessed by the Gini coefficient calculated by the Wagstaff method. Hypothesis 1 is supported. Greater income equality is most predictive of average height for both sexes. GNI_PPP explains a significant, but smaller, amount of the variation. National GDP has no association with height. Hypothesis 2 is rejected. With greater average adult height there is greater sexual dimorphism. Findings support a growing literature on the pernicious effects of inequality on growth in height and, by extension, on health. Gradients in height reflect gradients in social disadvantage. Inequality should be considered a pollutant that disempowers people from the resources needed for their own healthy growth and development and for the health and good growth of their children. © 2017 Wiley Periodicals, Inc.

A spatiotemporal multi-hazard exposure assessment based on property data

NASA Astrophysics Data System (ADS)

Fuchs, Sven; Keiler, Margreth; Zischg, Andreas

2016-04-01

The paper presents a nation-wide spatially explicit object-based assessment of buildings and citizens exposed to natural hazards in Austria, including river flooding, torrential flooding, and snow avalanches. The assessment was based on two different datasets, (a) hazard information providing input to the exposure of elements at risk, and (b) information on the building stock combined from different spatial data available on the national level. Hazard information was compiled from two different sources. For torrential flooding and snow avalanches available local-scale hazard maps were used, and for river flooding the results of the countrywide flood modelling eHORA were available. Information on the building stock contained information on the location and size of each building, as well as on the building category and the construction period. Additional information related to the individual floors, such as their height and net area, main purpose and configuration, was included for each property. Moreover, this dataset has an interface to the population register and allowed therefore retrieving the number of primary residents for each building. With the exception of sacral buildings, an economic module was used to compute the monetary value of buildings using (a) the information of the building register such as building type, number of storeys and utilisation, and (b) regionally averaged construction costs. It is shown that the repeatedly-stated assumption of increasing exposure due to continued population growth and related increase in assets has to be carefully evaluated by the local development of building stock. While some regions have shown a clearly above-average increase in assets, other regions were characterised by a below-average development. This mirrors the topography of the country, but also the different economic activities. While hotels and hostels are extraordinary prone to torrential flooding, commercial buildings as well as buildings used for recreation purpose are considerably exposed to river flooding. Residential buildings have shown an average exposure, compared to the number of buildings of this type in the overall building stock. In sum, around 5 % of all buildings are exposed to torrential flooding, and around 9 % to river flooding, with around 1 % of the buildings stock being multi-exposed. The temporal assessment of exposure has shown considerable differences in the dynamics of exposure to different hazard categories in comparison to the overall property stock. In conclusion, the presented object-based assessment is an important and suitable tool for nation-wide exposure assessment and may be used in operational risk management. Reference: Fuchs, S.; Keiler, M. & A. Zischg (2015): A spatiotemporal multi-hazard exposure assessment based on property data. Natural Hazards and Earth System Sciences 15 (9). p. 2127-2142

Aggregation of LoD 1 building models as an optimization problem

NASA Astrophysics Data System (ADS)

Guercke, R.; Götzelmann, T.; Brenner, C.; Sester, M.

3D city models offered by digital map providers typically consist of several thousands or even millions of individual buildings. Those buildings are usually generated in an automated fashion from high resolution cadastral and remote sensing data and can be very detailed. However, not in every application such a high degree of detail is desirable. One way to remove complexity is to aggregate individual buildings, simplify the ground plan and assign an appropriate average building height. This task is computationally complex because it includes the combinatorial optimization problem of determining which subset of the original set of buildings should best be aggregated to meet the demands of an application. In this article, we introduce approaches to express different aspects of the aggregation of LoD 1 building models in the form of Mixed Integer Programming (MIP) problems. The advantage of this approach is that for linear (and some quadratic) MIP problems, sophisticated software exists to find exact solutions (global optima) with reasonable effort. We also propose two different heuristic approaches based on the region growing strategy and evaluate their potential for optimization by comparing their performance to a MIP-based approach.

Control of Carbon Nanotube Density and Tower Height in an Array

NASA Technical Reports Server (NTRS)

Delzeit, Lance D. (Inventor); Schipper, John F. (Inventor)

2010-01-01

A method for controlling density or tower height of carbon nanotube (CNT) arrays grown in spaced apart first and second regions on a substrate. CNTs having a first density range (or first tower height range) are grown in the first region using a first source temperature range for growth. Subsequently or simultaneously, CNTs having a second density range (or second tower height range), having an average density (or average tower height) in the second region different from the average density (or average tower height) for the first region, are grown in the second region, using supplemental localized hearing for the second region. Application for thermal dissipation and/or dissipation of electrical charge or voltage in an electronic device are discussed.

The effect of step stool use and provider height on CPR quality during pediatric cardiac arrest: A simulation-based multicentre study.

PubMed

Cheng, Adam; Lin, Yiqun; Nadkarni, Vinay; Wan, Brandi; Duff, Jonathan; Brown, Linda; Bhanji, Farhan; Kessler, David; Tofil, Nancy; Hecker, Kent; Hunt, Elizabeth A

2018-01-01

We aimed to explore whether a) step stool use is associated with improved cardiopulmonary resuscitation (CPR) quality; b) provider adjusted height is associated with improved CPR quality; and if associations exist, c) determine whether just-in-time (JIT) CPR training and/or CPR visual feedback attenuates the effect of height and/or step stool use on CPR quality. We analysed data from a trial of simulated cardiac arrests with three study arms: No intervention; CPR visual feedback; and JIT CPR training. Step stool use was voluntary. We explored the association between 1) step stool use and CPR quality, and 2) provider adjusted height and CPR quality. Adjusted height was defined as provider height + 23 cm (if step stool was used). Below-average height participants were ≤ gender-specific average height; the remainder were above average height. We assessed for interaction between study arm and both adjusted height and step stool use. One hundred twenty-four subjects participated; 1,230 30-second epochs of CPR were analysed. Step stool use was associated with improved compression depth in below-average (female, p=0.007; male, p<0.001) and above-average (female, p=0.001; male, p<0.001) height providers. There is an association between adjusted height and compression depth (p<0.001). Visual feedback attenuated the effect of height (p=0.025) on compression depth; JIT training did not (p=0.918). Visual feedback and JIT training attenuated the effect of step stool use (p<0.001) on compression depth. Step stool use is associated with improved compression depth regardless of height. Increased provider height is associated with improved compression depth, with visual feedback attenuating the effects of height and step stool use.

Semantic 3d City Model to Raster Generalisation for Water Run-Off Modelling

NASA Astrophysics Data System (ADS)

Verbree, E.; de Vries, M.; Gorte, B.; Oude Elberink, S.; Karimlou, G.

2013-09-01

Water run-off modelling applied within urban areas requires an appropriate detailed surface model represented by a raster height grid. Accurate simulations at this scale level have to take into account small but important water barriers and flow channels given by the large-scale map definitions of buildings, street infrastructure, and other terrain objects. Thus, these 3D features have to be rasterised such that each cell represents the height of the object class as good as possible given the cell size limitations. Small grid cells will result in realistic run-off modelling but with unacceptable computation times; larger grid cells with averaged height values will result in less realistic run-off modelling but fast computation times. This paper introduces a height grid generalisation approach in which the surface characteristics that most influence the water run-off flow are preserved. The first step is to create a detailed surface model (1:1.000), combining high-density laser data with a detailed topographic base map. The topographic map objects are triangulated to a set of TIN-objects by taking into account the semantics of the different map object classes. These TIN objects are then rasterised to two grids with a 0.5m cell-spacing: one grid for the object class labels and the other for the TIN-interpolated height values. The next step is to generalise both raster grids to a lower resolution using a procedure that considers the class label of each cell and that of its neighbours. The results of this approach are tested and validated by water run-off model runs for different cellspaced height grids at a pilot area in Amersfoort (the Netherlands). Two national datasets were used in this study: the large scale Topographic Base map (BGT, map scale 1:1.000), and the National height model of the Netherlands AHN2 (10 points per square meter on average). Comparison between the original AHN2 height grid and the semantically enriched and then generalised height grids shows that water barriers are better preserved with the new method. This research confirms the idea that topographical information, mainly the boundary locations and object classes, can enrich the height grid for this hydrological application.

Improved vertical displacements induced by a refined thermal expansion model and its quantitative analysis in GPS height time series

NASA Astrophysics Data System (ADS)

Wang, Kaihua; Chen, Hua; Jiang, Weiping; Li, Zhao; Ma, Yifang; Deng, Liansheng

2018-04-01

There are apparent seasonal variations in GPS height time series, and thermal expansion is considered to be one of the potential geophysical contributors. The displacements introduced by thermal expansion are usually derived without considering the annex height and underground part of the monument (e.g. located on roof or top of the buildings), which may bias the geophysical explanation of the seasonal oscillation. In this paper, the improved vertical displacements are derived by a refined thermal expansion model where the annex height and underground depth of the monument are taken into account, and then 560 IGS stations are adopted to validate the modeled thermal expansion (MTE) displacements. In order to evaluate the impact of thermal expansion on GPS heights, the MTE displacements of 80 IGS stations with less data discontinuities are selected to compare with their observed GPS vertical (OGV) displacements with the modeled surface loading (MSL) displacements removed in advance. Quantitative analysis results show the maximum annual and semiannual amplitudes of the MTE are 6.65 mm (NOVJ) and 0.51 mm (IISC), respectively, and the maximum peak-to-peak oscillation of the MTE displacements can be 19.4 mm. The average annual amplitude reductions are 0.75 mm and 1.05 mm respectively after removing the MTE and MSL displacements from the OGV, indicating the seasonal oscillation induced by thermal expansion is equivalent to >75% of the impact of surface loadings. However, there are rarely significant reductions for the semiannual amplitude. Given the result in this study that thermal expansion can explain 17.3% of the annual amplitude in GPS heights on average, it must be precisely modeled both in GPS precise data processing and GPS time series analysis, especially for those stations located in the middle and high latitudes with larger annual temperature oscillation, or stations with higher monument.

View from intersection. Ninestory reinforced concrete building infilled with brick. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View from intersection. Nine-story reinforced concrete building infilled with brick. The street facades on beaubien and east grand are faced with stone accents and elaborate brick work. Brick pilasters run the entire height of the building. Steel tiebacks are apparent running up the height of the building on the east side. The large tower appears at the northeast and southeast corners - Detroit Storage Company, 2937 East Grand Boulevard, Detroit, MI

1. VIEW NORTHWEST, operations building, height finder radar tower, and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW NORTHWEST, operations building, height finder radar tower, and radar tower (unknown function) - Fort Custer Military Reservation, P-67 Radar Station, .25 mile north of Dickman Road, east of Clark Road, Battle Creek, Calhoun County, MI

47 CFR 73.813 - Determination of antenna height above average terrain (HAAT).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Determination of antenna height above average terrain (HAAT). 73.813 Section 73.813 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED... Determination of antenna height above average terrain (HAAT). HAAT determinations for LPFM stations will be made...

47 CFR 73.813 - Determination of antenna height above average terrain (HAAT).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Determination of antenna height above average terrain (HAAT). 73.813 Section 73.813 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED... Determination of antenna height above average terrain (HAAT). HAAT determinations for LPFM stations will be made...

47 CFR 73.813 - Determination of antenna height above average terrain (HAAT).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Determination of antenna height above average terrain (HAAT). 73.813 Section 73.813 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED... Determination of antenna height above average terrain (HAAT). HAAT determinations for LPFM stations will be made...

47 CFR 73.813 - Determination of antenna height above average terrain (HAAT).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Determination of antenna height above average terrain (HAAT). 73.813 Section 73.813 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED... Determination of antenna height above average terrain (HAAT). HAAT determinations for LPFM stations will be made...

Height diameter relations of maple street trees

Treesearch

David J. Nowak

1990-01-01

Height and diameter measurements were taken for silver, sugar and Norway maple street trees in Rochester and Syracuse, New York. Mature silver maples proved to be the tallest of the three species. Average sugar maple height was consistently taller than Norway maple height until diameters reached 28 inches. Average mature tree height for all three species level off in...

Performance Analysis of Air-to-Water Heat Pump in Latvian Climate Conditions

NASA Astrophysics Data System (ADS)

Kazjonovs, Janis; Sipkevics, Andrejs; Jakovics, Andris; Dancigs, Andris; Bajare, Diana; Dancigs, Leonards

2014-12-01

Strategy of the European Union in efficient energy usage demands to have a higher proportion of renewable energy in the energy market. Since heat pumps are considered to be one of the most efficient heating and cooling systems, they will play an important role in the energy consumption reduction in buildings aimed to meet the target of nearly zero energy buildings set out in the EU Directive 2010/31/EU. Unfortunately, the declared heat pump Coefficient of Performance (COP) corresponds to a certain outdoor temperature (+7 °C), therefore different climate conditions, building characteristics and settings result in different COP values during the year. The aim of this research is to investigate the Seasonal Performance factor (SPF) values of air-to-water heat pump which better characterize the effectiveness of heat pump in a longer selected period of time, especially during the winter season, in different types of residential buildings in Latvian climate conditions. Latvia has four pronounced seasons of near-equal length. Winter starts in mid-December and lasts until mid-March. Latvia is characterized by cold, maritime climate (duration of the average heating period being 203 days, the average outdoor air temperature during the heating period being 0.0 °C, the coldest five-day average temperature being -20.7 °C, the average annual air temperature being +6.2 °C, the daily average relative humidity being 79 %). The first part of this research consists of operational air-towater heat pump energy performance monitoring in different residential buildings during the winter season. The second part of the research takes place under natural conditions in an experimental construction stand which is located in an urban environment in Riga, Latvia. The inner area of this test stand, where air-to-water heat pump performance is analyzed, is 9 m2. The ceiling height is 3 m, all external wall constructions (U = 0.16 W/(m2K)) have ventilated facades. To calculate SPF, the experimental stand is equipped with sensors which provide measurements for electricity consumption and gained heat energy.

A diameter distribution approach to estimating average stand dominant height in Appalachian hardwoods

Treesearch

John R. Brooks

2007-01-01

A technique for estimating stand average dominant height based solely on field inventory data is investigated. Using only 45.0919 percent of the largest trees per acre in the diameter distribution resulted in estimates of average dominant height that were within 4.3 feet of the actual value, when averaged over stands of very different structure and history. Cubic foot...

A model for foam formation, stability, and breakdown in glass-melting furnaces.

PubMed

van der Schaaf, John; Beerkens, Ruud G C

2006-03-01

A dynamic model for describing the build-up and breakdown of a glass-melt foam is presented. The foam height is determined by the gas flux to the glass-melt surface and the drainage rate of the liquid lamellae between the gas bubbles. The drainage rate is determined by the average gas bubble radius and the physical properties of the glass melt: density, viscosity, surface tension, and interfacial mobility. Neither the assumption of a fully mobile nor the assumption of a fully immobile glass-melt interface describe the observed foam formation on glass melts adequately. The glass-melt interface appears partially mobile due to the presence of surface active species, e.g., sodium sulfate and silanol groups. The partial mobility can be represented by a single, glass-melt composition specific parameter psi. The value of psi can be estimated from gas bubble lifetime experiments under furnace conditions. With this parameter, laboratory experiments of foam build-up and breakdown in a glass melt are adequately described, qualitatively and quantitatively by a set of ordinary differential equations. An approximate explicit relationship for the prediction of the steady-state foam height is derived from the fundamental model.

Conducting experimental investigations of wind influence on high-rise constructions

NASA Astrophysics Data System (ADS)

Poddaeva, Olga I.; Fedosova, Anastasia N.; Churin, Pavel S.; Gribach, Julia S.

2018-03-01

The design of buildings with a height of more than 100 meters is accompanied by strict control in determining the external loads and the subsequent calculation of building structures, which is due to the uniqueness of these facilities. An important factor, the impact of which must be carefully studied at the stage of development of project documentation, is the wind. This work is devoted to the problem of studying the wind impact on buildings above 100 meters. In the article the technique of carrying out of experimental researches of wind influence on high-rise buildings and constructions, developed in the Educational-research-and-production laboratory on aerodynamic and aeroacoustic tests of building designs of NRU MGSU is presented. The publication contains a description of the main stages of the implementation of wind tunnel tests. The article presents the approbation of the methodology, based on the presented algorithm, on the example of a high-rise building under construction. This paper reflects the key requirements that are established at different stages of performing wind impact studies, as well as the results obtained, including the average values of the aerodynamic pressure coefficients, total forces and aerodynamic drag coefficients. Based on the results of the work, conclusions are presented.

A Robust Gradient Based Method for Building Extraction from LiDAR and Photogrammetric Imagery.

PubMed

Siddiqui, Fasahat Ullah; Teng, Shyh Wei; Awrangjeb, Mohammad; Lu, Guojun

2016-07-19

Existing automatic building extraction methods are not effective in extracting buildings which are small in size and have transparent roofs. The application of large area threshold prohibits detection of small buildings and the use of ground points in generating the building mask prevents detection of transparent buildings. In addition, the existing methods use numerous parameters to extract buildings in complex environments, e.g., hilly area and high vegetation. However, the empirical tuning of large number of parameters reduces the robustness of building extraction methods. This paper proposes a novel Gradient-based Building Extraction (GBE) method to address these limitations. The proposed method transforms the Light Detection And Ranging (LiDAR) height information into intensity image without interpolation of point heights and then analyses the gradient information in the image. Generally, building roof planes have a constant height change along the slope of a roof plane whereas trees have a random height change. With such an analysis, buildings of a greater range of sizes with a transparent or opaque roof can be extracted. In addition, a local colour matching approach is introduced as a post-processing stage to eliminate trees. This stage of our proposed method does not require any manual setting and all parameters are set automatically from the data. The other post processing stages including variance, point density and shadow elimination are also applied to verify the extracted buildings, where comparatively fewer empirically set parameters are used. The performance of the proposed GBE method is evaluated on two benchmark data sets by using the object and pixel based metrics (completeness, correctness and quality). Our experimental results show the effectiveness of the proposed method in eliminating trees, extracting buildings of all sizes, and extracting buildings with and without transparent roof. When compared with current state-of-the-art building extraction methods, the proposed method outperforms the existing methods in various evaluation metrics.

A Robust Gradient Based Method for Building Extraction from LiDAR and Photogrammetric Imagery

PubMed Central

Siddiqui, Fasahat Ullah; Teng, Shyh Wei; Awrangjeb, Mohammad; Lu, Guojun

2016-01-01

Existing automatic building extraction methods are not effective in extracting buildings which are small in size and have transparent roofs. The application of large area threshold prohibits detection of small buildings and the use of ground points in generating the building mask prevents detection of transparent buildings. In addition, the existing methods use numerous parameters to extract buildings in complex environments, e.g., hilly area and high vegetation. However, the empirical tuning of large number of parameters reduces the robustness of building extraction methods. This paper proposes a novel Gradient-based Building Extraction (GBE) method to address these limitations. The proposed method transforms the Light Detection And Ranging (LiDAR) height information into intensity image without interpolation of point heights and then analyses the gradient information in the image. Generally, building roof planes have a constant height change along the slope of a roof plane whereas trees have a random height change. With such an analysis, buildings of a greater range of sizes with a transparent or opaque roof can be extracted. In addition, a local colour matching approach is introduced as a post-processing stage to eliminate trees. This stage of our proposed method does not require any manual setting and all parameters are set automatically from the data. The other post processing stages including variance, point density and shadow elimination are also applied to verify the extracted buildings, where comparatively fewer empirically set parameters are used. The performance of the proposed GBE method is evaluated on two benchmark data sets by using the object and pixel based metrics (completeness, correctness and quality). Our experimental results show the effectiveness of the proposed method in eliminating trees, extracting buildings of all sizes, and extracting buildings with and without transparent roof. When compared with current state-of-the-art building extraction methods, the proposed method outperforms the existing methods in various evaluation metrics. PMID:27447631

Pixel-based approach for building heights determination by SAR radargrammetry

NASA Astrophysics Data System (ADS)

Dubois, C.; Thiele, A.; Hinz, S.

2013-10-01

Numerous advances have been made recently in photogrammetry, laser scanning, and remote sensing for the creation of 3D city models. More and more cities are interested in getting 3D city models, be it for urban planning purposes or for supporting public utility companies. In areas often affected by natural disaster, rapid updating of the 3D information may also be useful for helping rescue forces. The high resolutions that can be achieved by the new spaceborne SAR sensor generation enables the analysis of city areas at building level and make those sensors attractive for the extraction of 3D information. Moreover, they present the advantage of weather and sunlight independency, which make them more practicable than optical data, in particular for tasks where rapid response is required. Furthermore, their short revisit time and the possibility of multi-sensor constellation enable providing several acquisitions within a few hours. This opens up the floor for new applications, especially radargrammetric applications, which consider acquisitions taken under different incidence angles. In this paper, we present a new approach for determining building heights, relying only on the radargrammetric analysis of building layover. By taking into account same-side acquisitions, we present the workflow of building height determination. Focus is set on some geometric considerations, pixel-based approach for disparity map calculation, and analysis of the building layover signature for different configurations in order to determine building height.

36 CFR 910.54 - Build-to height.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 3 2011-07-01 2011-07-01 false Build-to height. 910.54 Section 910.54 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION GENERAL GUIDELINES AND UNIFORM STANDARDS FOR URBAN PLANNING AND DESIGN OF DEVELOPMENT WITHIN THE PENNSYLVANIA AVENUE...

36 CFR 910.54 - Build-to height.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Build-to height. 910.54 Section 910.54 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION GENERAL GUIDELINES AND UNIFORM STANDARDS FOR URBAN PLANNING AND DESIGN OF DEVELOPMENT WITHIN THE PENNSYLVANIA AVENUE...

Supply Ventilation and Prevention of Carbon Monoxide (II) Ingress into Building Premises

NASA Astrophysics Data System (ADS)

Litvinova, N. A.

2017-11-01

The article contains the relationships of carbon monoxide (II) concentration versus height-above-ground near buildings derived based on results of studies. The results of studies are crucial in preventing external pollutants ingress into a ventilation system. Being generated by external emission sources, such as motor vehicles and city heating plants, carbon monoxide (II) enters the premises during operation of a supply ventilation system. Fresh air nomographic charts were drawn to select the height of a fresh air intake into the ventilation system. Nomographic charts take into account external sources. The selected emission sources are located at various levels above ground relative to the building. The recommendations allow designing supply ventilation taking into account the quality of ambient air through the whole building height.

Ventilation Processes in a Three-Dimensional Street Canyon

NASA Astrophysics Data System (ADS)

Nosek, Štěpán; Kukačka, Libor; Kellnerová, Radka; Jurčáková, Klára; Jaňour, Zbyněk

2016-05-01

The ventilation processes in three different street canyons of variable roof geometry were investigated in a wind tunnel using a ground-level line source. All three street canyons were part of an urban-type array formed by courtyard-type buildings with pitched roofs. A constant roof height was used in the first case, while a variable roof height along the leeward or windward walls was simulated in the two other cases. All street-canyon models were exposed to a neutrally stratified flow with two approaching wind directions, perpendicular and oblique. The complexity of the flow and dispersion within the canyons of variable roof height was demonstrated for both wind directions. The relative pollutant removals and spatially-averaged concentrations within the canyons revealed that the model with constant roof height has higher re-emissions than models with variable roof heights. The nomenclature for the ventilation processes according to quadrant analysis of the pollutant flux was introduced. The venting of polluted air (positive fluctuations of both concentration and velocity) from the canyon increased when the wind direction changed from perpendicular to oblique, irrespective of the studied canyon model. Strong correlations (>0.5) between coherent structures and ventilation processes were found at roof level, irrespective of the canyon model and wind direction. This supports the idea that sweep and ejection events of momentum bring clean air in and detrain the polluted air from the street canyon, respectively.

Towards large-scale mapping of urban three-dimensional structure using Landsat imagery and global elevation datasets

NASA Astrophysics Data System (ADS)

Wang, P.; Huang, C.

2017-12-01

The three-dimensional (3D) structure of buildings and infrastructures is fundamental to understanding and modelling of the impacts and challenges of urbanization in terms of energy use, carbon emissions, and earthquake vulnerabilities. However, spatially detailed maps of urban 3D structure have been scarce, particularly in fast-changing developing countries. We present here a novel methodology to map the volume of buildings and infrastructures at 30 meter resolution using a synergy of Landsat imagery and openly available global digital surface models (DSMs), including the Shuttle Radar Topography Mission (SRTM), ASTER Global Digital Elevation Map (GDEM), ALOS World 3D - 30m (AW3D30), and the recently released global DSM from the TanDEM-X mission. Our method builds on the concept of object-based height profile to extract height metrics from the DSMs and use a machine learning algorithm to predict height and volume from the height metrics. We have tested this algorithm in the entire England and assessed our result using Lidar measurements in 25 England cities. Our initial assessments achieved a RMSE of 1.4 m (R2 = 0.72) for building height and a RMSE of 1208.7 m3 (R2 = 0.69) for building volume, demonstrating the potential of large-scale applications and fully automated mapping of urban structure.

Traffic-related immissions and their impact on historic buildings and monuments

NASA Astrophysics Data System (ADS)

Auras, M.; Beer, S.; Bundschuh, P.; Eichhorn, J.; Mach, M.; Scheuvens, D.; Schorling, M.; von Schumann, J.; Snethlage, R.; Weinbruch, S.

2012-04-01

Air quality in Germany has improved essentially over the last decades. Because the concentrations of sulfur dioxide were reduced by more than 90% between 1990 and 2007 acid rain no longer seems to play a relevant role in the weathering of natural stone facades of historic buildings. But in the surroundings of urban traffic hot spots high emissions of nitrogen oxides and fine particulate matter (PM10) are observed. Therefore the question arises whether these airborne pollutants bear a potential for future damage of natural stone and other construction materials. In an interdisciplinary research program different approaches were pursued to evaluate the damage potential of today's traffic-induced immissions by exemplarily investigating two German cities, Mainz and Munich. First calculations of average weathering rates for the stones concerned were made using the dose-response functions of the MULTI ASSESS program and the immission data from survey stations at traffic hot spots and at housing areas. Than the distribution of traffic-induced immissions (NO2 and PM10) in the surrounding areas of major traffic pathways was calculated for both cities with the simulation program WINkfz. The resulting maps of mean pollutant concentrations were superimposed to inventory maps of historical monuments to allow the identification of monuments with high pollution loads. Additionally different classes of natural stones were distinguished regarding their chemical reactivity. Two prominent monuments with high traffic-induced pollution loads were selected for small scale simulations of pollutant immissions with the simulation program MISKAM. The dispersion of pollutants to different directions and building heights were calculated and the influence of broadleaf trees in the surrounding of the buildings was evaluated (summer versus winter situation). PM10 measurements were carried out at different building heights of the two buildings. Collection of PM10 dust and single-particle analyses by ESEM permits the classification of PM10 particles and the identification and quantification of the traffic-induced part of total PM10.

Analysis of In-Canyon Flow Characterisitcs in step-up street canyons

NASA Astrophysics Data System (ADS)

PARK, S.; Kim, J.; Choi, W.; Pardyjak, E.

2017-12-01

Flow characteristics in strep-up street canyons were investigated focusing on in-canyon region. To see the effects of the building geometry, two building height ratios [ratio of the upwind (Hu) to downwind building heights (Hd) = 0.33, 0.6] were considered and eight building length ratios [ratio of the cross-wind building length (L) to street-canyon width (S) from 0.5 to 4 with the increment of 0.5] were systematically changed. For the model validation, the simulated results were compared with the wind- tunnel data measured for Hu/Hd = 0.33, 0.6 and L/S = 1, 2, 3, and 4. In the CFD model simulations, the corner vortices at the downwind side near the ground level and the recirculation zones above the downwind buildings had the relatively small extents, compared with those in the wind-tunnel experiments. However, the CFD model reproduced the main flow features such as the street-canyon vortices, circulations above the building roof, and the positions of the stagnation points on the downwind building walls in the wind-tunnel experiments reasonably well. By further analyzing the three-dimensional flow structures based on the numerical results simulated in the step-up street canyons, we schematically suggested the flow characteristics with different building-height and building-length ratios.

A Numerical Simulation of Traffic-Related Air Pollution Exposures in Urban Street Canyons

NASA Astrophysics Data System (ADS)

Liu, J.; Fu, X.; Tao, S.

2016-12-01

Urban street canyons are usually associated with intensive vehicle emissions. However, the high buildings successively along both sides of a street block the dispersion of traffic-generated air pollutants, which enhances human exposure and adversely affects human health. In this study, an urban scale traffic pollution dispersion model is developed with the consideration of street distribution, canyon geometry, background meteorology, traffic assignment, traffic emissions and air pollutant dispersion. Vehicle exhausts generated from traffic flows will first disperse inside a street canyon along the micro-scale wind field (generated by computational fluid dynamics (CFD) model) and then leave the street canyon and further disperse over the urban area. On the basis of this model, the effects of canyon geometry on the distribution of NOx and CO from traffic emissions were studied over the center of Beijing, China. We found that an increase of building height along the streets leads to higher pollution levels inside streets and lower pollution levels outside, resulting in higher domain-averaged concentrations over the area. In addition, street canyons with equal (or highly uneven) building heights on two sides of a street tend to lower the urban-scale air pollution concentrations at pedestrian level. Our results indicate that canyon geometry strongly influences human exposure to traffic pollutants in the populated urban area. Carefully planning street layout and canyon geometry in consideration of traffic demand as well as local weather pattern may significantly reduce the chances of unhealthy air being inhaled by urban residents.

47 CFR 24.53 - Calculation of height above average terrain (HAAT).

Code of Federal Regulations, 2012 CFR

2012-10-01

... height above mean sea level. (b) Average terrain elevation shall be calculated using elevation data from... Digital Chart of the World (DCW) may be used. (c) Radial average terrain elevation is calculated as the...

47 CFR 24.53 - Calculation of height above average terrain (HAAT).

Code of Federal Regulations, 2011 CFR

2011-10-01

... height above mean sea level. (b) Average terrain elevation shall be calculated using elevation data from... Digital Chart of the World (DCW) may be used. (c) Radial average terrain elevation is calculated as the...

47 CFR 24.53 - Calculation of height above average terrain (HAAT).

Code of Federal Regulations, 2010 CFR

2010-10-01

... height above mean sea level. (b) Average terrain elevation shall be calculated using elevation data from... Digital Chart of the World (DCW) may be used. (c) Radial average terrain elevation is calculated as the...

47 CFR 24.53 - Calculation of height above average terrain (HAAT).

Code of Federal Regulations, 2014 CFR

2014-10-01

... height above mean sea level. (b) Average terrain elevation shall be calculated using elevation data from... Digital Chart of the World (DCW) may be used. (c) Radial average terrain elevation is calculated as the...

47 CFR 24.53 - Calculation of height above average terrain (HAAT).

Code of Federal Regulations, 2013 CFR

2013-10-01

... height above mean sea level. (b) Average terrain elevation shall be calculated using elevation data from... Digital Chart of the World (DCW) may be used. (c) Radial average terrain elevation is calculated as the...

Differences in Body Build in Children of Different Ethnic Groups and their Impact on the Prevalence of Stunting, Thinness, Overweight, and Obesity.

PubMed

Poh, Bee Koon; Wong, Jyh Eiin; Norimah, A Karim; Deurenberg, Paul

2016-03-01

The prevalence of stunting, thinness, overweight, and obesity among children differs by ethnicity. It is not known whether differences in body build across the ethnic groups influence the interpretation of nutritional parameters. To explore the differences in body build across the 5 main ethnic groups in Malaysia and to determine whether differences in body build have an impact on the interpretation of nutrition indicators. A total of 3227 children aged 2.0 to 12.9 years who participated in the South East Asian Nutrition Surveys (SEANUTS) in Malaysia were included in this analysis. Body weight, height, sitting height, wrist and knee breadths, and biceps and subscapular skinfolds were measured, and relative leg length, slenderness index, and sum of skinfolds were calculated. Z scores for height-for-age (HAZ) and body mass index-for-age (BAZ) were calculated using the World Health Organization (WHO) 2007 growth standards. Differences in relative leg length and slenderness across the ethnic groups were correlated with HAZ and BAZ. Correction for differences in body build did, in some ethnic groups, have significant impact on the prevalence of stunting, thinness, overweight, and obesity, and the pattern of prevalence across ethnic groups changed. At the population level, corrections for body build had only minor and mostly nonsignificant effects on prevalence, but at an individual level, corrections for body build placed a substantial number of children in different height or weight categories. Whether these misclassifications warrant additional assessment of body build in clinical practice will need further investigation. © The Author(s) 2016.

Footprint Map Partitioning Using Airborne Laser Scanning Data

NASA Astrophysics Data System (ADS)

Xiong, B.; Oude Elberink, S.; Vosselman, G.

2016-06-01

Nowadays many cities and countries are creating their 3D building models for a better daily management and smarter decision making. The newly created 3D models are required to be consistent with existing 2D footprint maps. Thereby the 2D maps are usually combined with height data for the task of 3D reconstruction. Many buildings are often composed by parts that are discontinuous over height. Building parts can be reconstructed independently and combined into a complete building. Therefore, most of the state-of-the-art work on 3D building reconstruction first decomposes a footprint map into parts. However, those works usually change the footprint maps for easier partitioning and cannot detect building parts that are fully inside the footprint polygon. In order to solve those problems, we introduce two methodologies, one more dependent on height data, and the other one more dependent on footprints. We also experimentally evaluate the two methodologies and compare their advantages and disadvantages. The experiments use Airborne Laser Scanning (ALS) data and two vector maps, one with 1:10,000 scale and another one with 1:500 scale.

Plume Dispersion over Idealized Urban-liked Roughness with Height Variation: an LES Approach

NASA Astrophysics Data System (ADS)

Wong, Colman Ching Chi; Liu, Chun-Ho

2013-04-01

Human activities (e.g. vehicular emission) are the primary pollutant sources affecting the health and living quality of stakeholders in modern compact cities. Gaussian plume dispersion model is commonly used for pollutant distribution estimate that works well over rural areas with flat terrain. However, its major parameters, dispersion coefficients, exclude the effect of surface roughness that unavoidably prone to error handling the pollutant transport in the urban boundary layer (UBL) over building roughness. Our recent large-eddy simulation (LES) has shown that urban surfaces affect significantly the pollutant dispersion over idealized, identical two-dimensional (2D) street canyons of uniform height. As an extension to our on-going effort, this study is conceived to investigate how rough urban surfaces, which are constructed by 2D street canyons of non-uniform height, modify the UBL pollutant dispersion . A series of LESs with idealized roughness elements of non-uniform heights were performed in neutral stratification. Building models with two different heights were placed alternatively in the computational domain to construct 2D street canyons in cross flows. The plume dispersion from a ground-level passive pollutant source over more realistic urban areas was then examined. Along with the existing building-height-to-street-width (aspect) ratio (AR), a new parameter, building-height variability (BHV), is used to measure the building height unevenness. Four ARs (1, 0.5, 0.25 and 0.125) and three BHVs (20%, 40% and 60%) were considered in this study. Preliminary results show that BHV greatly increases the aerodynamic roughness of the hypothetical urban surfaces for narrow street canyons. Analogous to our previous findings, the air exchange rate (ACH) of street canyons increases with increasing friction factor, implying that street-level ventilation could be improved by increasing building roughness via BHV. In addition, the parameters used in dispersion coefficient estimates are related to the friction factor in the way similar to that of uniform street canyons, i.e. they are linear functions of friction factor when the roughness is small and become insensitive to friction factor thereafter over very rough surfaces. It is thus suggested that aerodynamic resistance is the key factor affecting the air quality in urban areas. Moreover, the friction factor could be used to parameterize the dispersion coefficients over different roughness elements.

Fetal programming of body dimensions and percentage body fat measured in prepubertal children with a 4-component model of body composition, dual-energy X-ray absorptiometry, deuterium dilution, densitometry, and skinfold thicknesses.

PubMed

Elia, Marinos; Betts, Peter; Jackson, Diane M; Mulligan, Jean

2007-09-01

Intrauterine programming of body composition [percentage body fat (%BF)] has been sparsely examined with multiple independent reference techniques in children. The effects on and consequences of body build (dimensions, mass, and length of body segments) are unclear. The study examined whether percentage fat and relation of percentage fat to body mass index (BMI; in kg/m2) in prepubertal children are programmed during intrauterine development and are dependent on body build. It also aimed to examine the extent to which height can be predicted by parental height and birth weight. Eighty-five white children (44 boys, 41 girls; aged 6.5-9.1 y) had body composition measured with a 4-component model (n = 58), dual-energy X-ray absorptiometry (n = 84), deuterium dilution (n = 81), densitometry (n = 62), and skinfold thicknesses (n = 85). An increase in birth weight of 1 SD was associated with a decrease of 1.95% fat as measured by the 4-component model (P = 0.012) and 0.82-2.75% by the other techniques. These associations were independent of age, sex, socioeconomic status, physical activity, BMI, and body build. Body build did not decrease the strength of the associations. Birth weight was a significantly better predictor of height than was self-reported midparental height, accounting for 19.4% of the variability at 5 y of age and 10.3% at 7.8 y of age (17.8% and 8.8% of which were independent of parental height at these ages, respectively). Consistent trends across body-composition measurement techniques add strength to the suggestion that percentage fat in prepubertal children is programmed in utero (independently of body build and BMI). It also suggests birth weight is a better predictor of prepubertal height than is self-reported midparental height.

Why are Mexican American boys so much taller now?

PubMed

Delajara, Marcelo; Rodríguez-Segura, Melissa

2010-07-01

Using NHANES data we find that the difference in average height between non-Hispanic White and Mexican American boys of ages 2-14 years has decreased 1.7 cm on average during the last quarter of the twentieth century in the United States. Our hypothesis is that the narrowing of the height gap is related to a larger gain in maternal height among Mexican Americans in relation to Whites. We estimate a child's height equation and find that on average about 38% of the reduction in the gap for boys of ages 2-5 years is attributed to this factor. The evidence of a secular trend for height is weak for the case of girls. 2010 Elsevier B.V. All rights reserved.

Assessment of codes, by-laws and regulations relating to air wells in building design

NASA Astrophysics Data System (ADS)

Fadzil, Sharifah Fairuz Syed; Karamazaman, Nazli

2017-10-01

Codes and by-laws concerning air well design (for buildings and lavatories) in Malaysia has been established in the Malaysian Uniform Building By-Laws UBBL number 40 (1) and (2) since the 1980s. Wells are there to fulfill the ventilation and daylighting requirements. The minimum well area according to building storey height are compared between UBBL and the Singapore's well requirements from the Building Construction Authority BCA. A visual and graphical representation (with schematics building and well diagrams drawn to scale) of the minimum well sizes and dimensions is given. It can be seen that if the minimum requirement of well size is used for buildings above 8 storeys high, a thin well resulted which is not proportionate to the building height. A proposed dimension is graphed and given to be used in the UBBL which translated to graphics (3 dimensional buildings drawn to scale) created a much better well proportion.

1. WEST SIDE, NORTH END OF BUILDING 1. SHOWS ADDITIONAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. WEST SIDE, NORTH END OF BUILDING 1. SHOWS ADDITIONAL ANGLES IN BUILDING AT SOUTHERN END. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

Height and calories in early childhood.

PubMed

Griffen, Andrew S

2016-03-01

This paper estimates a height production function using data from a randomized nutrition intervention conducted in rural Guatemala from 1969 to 1977. Using the experimental intervention as an instrument, the IV estimates of the effect of calories on height are an order of magnitude larger than the OLS estimates. Information from a unique measurement error process in the calorie data, counterfactuals results from the estimated model and external evidence from migration studies suggest that IV is not identifying a policy relevant average marginal impact of calories on height. The preferred, attenuation bias corrected OLS estimates from the height production function suggest that, averaging over ages, a 100 calorie increase in average daily calorie intake over the course of a year would increase height by 0.06 cm. Counterfactuals from the model imply that calories gaps in early childhood can explain at most 16% of the height gap between Guatemalan children and the US born children of Guatemalan immigrants. Copyright © 2015 Elsevier B.V. All rights reserved.

1. VIEW LOOKING NORTH IN SHOP AREA. BUILDING 15 ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW LOOKING NORTH IN SHOP AREA. BUILDING 15 ON RIGHT, BUILDING 22 ON LEFT, AND BUILDING 1 IN DISTANCE. - Chollas Heights Naval Radio Transmitting Facility, 6410 Zero Road, San Diego, San Diego County, CA

Experimental measurements of heat transfer coefficient in a partially/fully opened tilted cavity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chakroun, W.; Elsayed, M.M.; Al-Fahed, S.F.

1997-11-01

An experimental investigation was carried out to determine the heat transfer coefficient from a rectangular tilted cavity to the ambient due to the buoyancy driven flow in the cavity. The cavity is partially or fully open from one side. All the walls of the cavity are adiabatic except the wall facing the cavity opening which is heated at a constant heat flux. Air was used as the cavity fluid and the experiments were carried out at a flux Grashof number of 5.5 {times} 10{sup 8}. The tilt angle of the cavity, measured from the vertical direction, was changed between {minus}90more » deg to +90 deg in 15 deg increments. Also, geometries of aspect ratio (height-to-width of cavity) of 1.0, 0.5, and 0.25 and of opening ratio (opening height to cavity height) of 1.0, 0.5, and 0.25 were considered in the study. The results are presented in terms of the average Nusselt number for different values of the above experimental parameters. Conclusions are derived for the effect of changing the tilt angle, the aspect ratio, or the opening ratio of the cavity on the average heat transfer coefficient between the cavity and the ambient air. Buoyancy-driven flow in rectangular cavities has been widely investigated by many researchers. This geometry is of special interest in many solar applications such as in solar passive heating, solar concentrators, and solar central receivers. The importance of the geometry extends to other engineering applications such as electronic equipment, fire research, and energy conservation in buildings.« less

Survival and growth of black walnut families after 7 years in West Virginia

Treesearch

G. W. Wendel; Donald E. Dorn; Donald E. Dorn

1985-01-01

Average survival, 7-year stem diameter, and stem diameter growth differed significantly among 34 black walnut families planted in West Virginia. Average total height, height growth, and diameter at breast height were not significantly different among families. Families were from seed collected in West Virginia, Pennsylvania, North Carolina, and Tennessee. The 7-year...

A modified 3D algorithm for road traffic noise attenuation calculations in large urban areas.

PubMed

Wang, Haibo; Cai, Ming; Yao, Yifan

2017-07-01

The primary objective of this study is the development and application of a 3D road traffic noise attenuation calculation algorithm. First, the traditional empirical method does not address problems caused by non-direct occlusion by buildings and the different building heights. In contrast, this study considers the volume ratio of the buildings and the area ratio of the projection of buildings adjacent to the road. The influence of the ground affection is analyzed. The insertion loss due to barriers (infinite length and finite barriers) is also synthesized in the algorithm. Second, the impact of different road segmentation is analyzed. Through the case of Pearl River New Town, it is recommended that 5° is the most appropriate scanning angle as the computational time is acceptable and the average error is approximately 3.1 dB. In addition, the algorithm requires only 1/17 of the time that the beam tracking method requires at the cost of more imprecise calculation results. Finally, the noise calculation for a large urban area with a high density of buildings shows the feasibility of the 3D noise attenuation calculation algorithm. The algorithm is expected to be applied in projects requiring large area noise simulations. Copyright © 2017 Elsevier Ltd. All rights reserved.

7. WINDOW DETAIL SOUTHERN WALL OF BUILDING. (SOUTH SIDE OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. WINDOW DETAIL SOUTHERN WALL OF BUILDING. (SOUTH SIDE OF BUILDING 4 IS NOW WITHIN BUILDING 40 GARAGE.) - Chollas Heights Naval Radio Transmitting Facility, Public Works Shop, 6410 Zero Road, San Diego, San Diego County, CA

3. VIEW SHOWING RELATIONSHIP OF EAST SIDES OF BUILDINGS 15 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. VIEW SHOWING RELATIONSHIP OF EAST SIDES OF BUILDINGS 15 ON LEFT, BUILDING 40 GARAGE IN CENTER, AND BUILDING 4 IN DISTANCE. - Chollas Heights Naval Radio Transmitting Facility, 6410 Zero Road, San Diego, San Diego County, CA

Wind Tunnel Study on Flows over Various Two-dimensional Idealized Urban-liked Surfaces

NASA Astrophysics Data System (ADS)

Ho, Yat-Kiu; Liu, Chun-Ho

2013-04-01

Extensive human activities (e.g. increased traffic emissions) emit a wide range of pollutants resulting in poor urban area air quality. Unlike open, flat and homogenous rural terrain, urban surface is complicated by the presence of buildings, obstacles and narrow streets. The irregular urban surfaces thus form a random roughness that further modifies the near-surface flows and pollutant dispersion. In this study, a physical modelling approach is employed to commence a series of wind tunnel experiments to study the urban-area air pollution problems. The flow characteristics over different hypothetical urban roughness surfaces were studied in a wind tunnel in isothermal conditions. Preliminary experiments were conducted based on six types of idealized two-dimensional (2D) street canyon models with various building-height-to-street-width (aspect) ratios (ARs) 1, 1/2, 1/4, 1/8, 1/10 and 1/12. The main instrumentation is an in-house 90o X-hotwire anemometry. In each set of configuration, a sampling street canyon was selected near the end of the streamwise domain. Its roof level, i.e. the transverse between the mid points of the upstream and downstream buildings, was divided into eight segments. The measurements were then recorded on the mid-plane of the spannwise domain along the vertical profile (from building roof level to the ceiling of wind tunnel) of the eight segments. All the data acquisition processes were handled by the NI data acquisition modules, NI 9239 and CompactDAQ-9188 hardware. Velocity calculation was carried out in the post-processing stage on a digital computer. The two-component flow velocities and velocity fluctuations were calculated at each sampling points, therefore, for each model, a streamwise average of eight vertical profiles of mean velocity and velocity fluctuations was presented. A plot of air-exchange rate (ACH) against ARs was also presented in order to examine the ventilation performance of different tested models. Preliminary results show that the near-ground turbulence behaviour (2 to 5 times of the building height) is relatively sensitive to the changes in ARs. The wider the streets (decrease in AR), the higher the turbulence level was observed. A similar behaviour is observed on the ventilation performance in which the ACH was increased with decreasing AR. Interestingly, a peak ACH value was observed around AR = 1/10 and was slightly dropped thereafter at AR = 1/12. The observation is in line with our previous large-eddy simulation (LES) results. These findings indicate that variability of urban-like surfaces is important to the near-ground turbulent boundary layer structure. Additional measurements on the flows and dispersions over building surfaces will be undertaken on a variety of ARs and building height variations to elucidate the complex transport and pollutant dispersion mechanism in urban areas.

Modified Maturity Offset Prediction Equations: Validation in Independent Longitudinal Samples of Boys and Girls.

PubMed

Kozieł, Sławomir M; Malina, Robert M

2018-01-01

Predicted maturity offset and age at peak height velocity are increasingly used with youth athletes, although validation studies of the equations indicated major limitations. The equations have since been modified and simplified. The objective of this study was to validate the new maturity offset prediction equations in independent longitudinal samples of boys and girls. Two new equations for boys with chronological age and sitting height and chronological age and stature as predictors, and one equation for girls with chronological age and stature as predictors were evaluated in serial data from the Wrocław Growth Study, 193 boys (aged 8-18 years) and 198 girls (aged 8-16 years). Observed age at peak height velocity for each youth was estimated with the Preece-Baines Model 1. The original prediction equations were included for comparison. Predicted age at peak height velocity was the difference between chronological age at prediction and maturity offset. Predicted ages at peak height velocity with the new equations approximated observed ages at peak height velocity in average maturing boys near the time of peak height velocity; a corresponding window for average maturing girls was not apparent. Compared with observed age at peak height velocity, predicted ages at peak height velocity with the new and original equations were consistently later in early maturing youth and earlier in late maturing youth of both sexes. Predicted ages at peak height velocity with the new equations had reduced variation compared with the original equations and especially observed ages at peak height velocity. Intra-individual variation in predicted ages at peak height velocity with all equations was considerable. The new equations are useful for average maturing boys close to the time of peak height velocity; there does not appear to be a clear window for average maturing girls. The new and original equations have major limitations with early and late maturing boys and girls.

a New Mask for Automatic Building Detection from High Density Point Cloud Data and Multispectral Imagery

NASA Astrophysics Data System (ADS)

Awrangjeb, M.; Siddiqui, F. U.

2017-11-01

In complex urban and residential areas, there are buildings which are not only connected with and/or close to one another but also partially occluded by their surrounding vegetation. Moreover, there may be buildings whose roofs are made of transparent materials. In transparent buildings, there are point returns from both the ground (or materials inside the buildings) and the rooftop. These issues confuse the previously proposed building masks which are generated from either ground points or non-ground points. The normalised digital surface model (nDSM) is generated from the non-ground points and usually it is hard to find individual buildings and trees using the nDSM. In contrast, the primary building mask is produced using the ground points, thereby it misses the transparent rooftops. This paper proposes a new building mask based on the non-ground points. The dominant directions of non-ground lines extracted from the multispectral imagery are estimated. A dummy grid with the target mask resolution is rotated at each dominant direction to obtain the corresponding height values from the non-ground points. Three sub-masks are then generated from the height grid by estimating the gradient function. Two of these sub-masks capture planar surfaces whose height remain constant in along and across the dominant direction, respectively. The third sub-mask contains only the flat surfaces where the height (ideally) remains constant in all directions. All the sub-masks generated in all estimated dominant directions are combined to produce the candidate building mask. Although the application of the gradient function helps in removal of most of the vegetation, the final building mask is obtained through removal of planar vegetation, if any, and tiny isolated false candidates. Experimental results on three Australian data sets show that the proposed method can successfully remove vegetation, thereby separate buildings from occluding vegetation and detect buildings with transparent roof materials. While compared to existing building detection techniques, the proposed technique offers higher objectbased completeness, correctness and quality, specially in complex scenes with aforementioned issues. It is not only capable of detecting transparent buildings, but also small garden sheds which are sometimes as small as 5 m2 in area.

47 CFR 73.314 - Field strength measurements.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., such as topography, height and types of vegetation, buildings, obstacles, weather, and other local... the approximate time of measurement, weather, topography, overhead wiring, heights and types of...

47 CFR 73.314 - Field strength measurements.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., such as topography, height and types of vegetation, buildings, obstacles, weather, and other local... the approximate time of measurement, weather, topography, overhead wiring, heights and types of...

47 CFR 73.314 - Field strength measurements.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., such as topography, height and types of vegetation, buildings, obstacles, weather, and other local... the approximate time of measurement, weather, topography, overhead wiring, heights and types of...

47 CFR 73.314 - Field strength measurements.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., such as topography, height and types of vegetation, buildings, obstacles, weather, and other local... the approximate time of measurement, weather, topography, overhead wiring, heights and types of...

6. VIEW SOUTH TOWARD SOUTHERN PORTION OF BUILDING 1. GARAGE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. VIEW SOUTH TOWARD SOUTHERN PORTION OF BUILDING 1. GARAGE ADDITION AT LEFT. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

9. LOOKING NORTHWEST TOWARD SOUTHERN SIDES OF BUILDING 1. GARAGE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. LOOKING NORTHWEST TOWARD SOUTHERN SIDES OF BUILDING 1. GARAGE ADDITION AT RIGHT. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

Efficient visualization of urban spaces

NASA Astrophysics Data System (ADS)

Stamps, A. E.

2012-10-01

This chapter presents a new method for calculating efficiency and applies that method to the issues of selecting simulation media and evaluating the contextual fit of new buildings in urban spaces. The new method is called "meta-analysis". A meta-analytic review of 967 environments indicated that static color simulations are the most efficient media for visualizing urban spaces. For contextual fit, four original experiments are reported on how strongly five factors influence visual appeal of a street: architectural style, trees, height of a new building relative to the heights of existing buildings, setting back a third story, and distance. A meta-analysis of these four experiments and previous findings, covering 461 environments, indicated that architectural style, trees, and height had effects strong enough to warrant implementation, but the effects of setting back third stories and distance were too small to warrant implementation.

Comparison of two recent storm surge events based on results of field surveys

NASA Astrophysics Data System (ADS)

Nakamura, Ryota; Shibayama, Tomoya; Mikami, Takahito; Esteban, Miguel; Takagi, Hiroshi; Maell, Martin; Iwamoto, Takumu

2017-10-01

This paper compares two different types of storm surge disaster based on field surveys. Two cases: a severe storm surge flood with its height of over 5 m due to Typhoon Haiyan (2013) in Philippine, and inundation of storm surge around Nemuro city in Hokkaido of Japan with its maximum surge height of 2.8 m caused by extra-tropical cyclone are taken as examples. For the case of the Typhoon Haiyan, buildings located in coastal region were severely affected due to a rapidly increase in ocean surface. The non-engineering buildings were partially or completely destroyed due to their debris transported to an inner bay region. In fact, several previous reports indicated two unique features, bore-like wave and remarkably high speed currents. These characteristics of the storm surge may contribute to a wide-spread corruption for the buildings around the affected region. Furthermore, in the region where the surge height was nearly 3 m, the wooden houses were completely or partially destroyed. On the other hand, in Nemuro city, a degree of suffering in human and facility caused by the storm surge is minor. There was almost no partially destroyed residential houses even though the height of storm surge reached nearly 2.8 m. An observation in the tide station in Nemuro indicated that this was a usual type of storm surge, which showed a gradual increase of sea level height in several hours without possessing the unique characteristics like Typhoon Haiyan. As a result, not only the height of storm surge but also the robustness of the buildings and characteristics of storm surge, such as bore like wave and strong currents, determined the existent of devastation in coastal regions.

An international ecological study of adult height in relation to cancer incidence for 24 anatomical sites.

PubMed

Jiang, Yannan; Marshall, Roger J; Walpole, Sarah C; Prieto-Merino, David; Liu, Dong-Xu; Perry, Jo K

2015-03-01

Anthropometric indices associated with childhood growth and height attained in adulthood, have been associated with an increased incidence of certain malignancies. To evaluate the cancer-height relationship, we carried out a study using international data, comparing various cancer rates with average adult height of women and men in different countries. An ecological analysis of the relationship between country-specific cancer incidence rates and average adult height was conducted for twenty-four anatomical cancer sites. Age-standardized rates were obtained from GLOBOCAN 2008. Average female (112 countries) and male (65 countries) heights were sourced and compiled primarily from national health surveys. Graphical and weighted regression analysis was conducted, taking into account BMI and controlling for the random effect of global regions. A significant positive association between a country's average adult height and the country's overall cancer rate was observed in both men and women. Site-specific cancer incidence for females was positively associated with height for most cancers: lung, kidney, colorectum, bladder, melanoma, brain and nervous system, breast, non-Hodgkin lymphoma, multiple myeloma, corpus uteri, ovary, and leukemia. A significant negative association was observed with cancer of the cervix uteri. In males, site-specific cancer incidence was positively associated with height for cancers of the brain and nervous system, kidney, colorectum, non-Hodgkin lymphoma, multiple myeloma, prostate, testicular, lip and oral cavity, and melanoma. Incidence of cancer was associated with tallness in the majority of anatomical/cancer sites investigated. The underlying biological mechanisms are unclear, but may include nutrition and early-life exposure to hormones, and may differ by anatomical site.

Averaging interval selection for the calculation of Reynolds shear stress for studies of boundary layer turbulence.

NASA Astrophysics Data System (ADS)

Lee, Zoe; Baas, Andreas

2013-04-01

It is widely recognised that boundary layer turbulence plays an important role in sediment transport dynamics in aeolian environments. Improvements in the design and affordability of ultrasonic anemometers have provided significant contributions to studies of aeolian turbulence, by facilitating high frequency monitoring of three dimensional wind velocities. Consequently, research has moved beyond studies of mean airflow properties, to investigations into quasi-instantaneous turbulent fluctuations at high spatio-temporal scales. To fully understand, how temporal fluctuations in shear stress drive wind erosivity and sediment transport, research into the best practice for calculating shear stress is necessary. This paper builds upon work published by Lee and Baas (2012) on the influence of streamline correction techniques on Reynolds shear stress, by investigating the time-averaging interval used in the calculation. Concerns relating to the selection of appropriate averaging intervals for turbulence research, where the data are typically non-stationary at all timescales, are well documented in the literature (e.g. Treviño and Andreas, 2000). For example, Finnigan et al. (2003) found that underestimating the required averaging interval can lead to a reduction in the calculated momentum flux, as contributions from turbulent eddies longer than the averaging interval are lost. To avoid the risk of underestimating fluxes, researchers have typically used the total measurement duration as a single averaging period. For non-stationary data, however, using the whole measurement run as a single block average is inadequate for defining turbulent fluctuations. The data presented in this paper were collected in a field study of boundary layer turbulence conducted at Tramore beach near Rosapenna, County Donegal, Ireland. High-frequency (50 Hz) 3D wind velocity measurements were collected using ultrasonic anemometry at thirteen different heights between 0.11 and 1.62 metres above the bed. A technique for determining time-averaging intervals for a series of anemometers stacked in a close vertical array is presented. A minimum timescale is identified using spectral analysis to determine the inertial sub-range, where energy is neither produced nor dissipated but passed down to increasingly smaller scales. An autocorrelation function is then used to derive a scaling pattern between anemometer heights, which defines a series of averaging intervals of increasing length with height above the surface. Results demonstrate the effect of different averaging intervals on the calculation of Reynolds shear stress and highlight the inadequacy of using the total measurement duration as a single block average. Lee, Z. S. & Baas, A. C. W. (2012). Streamline correction for the analysis of boundary layer turbulence. Geomorphology, 171-172, 69-82. Treviño, G. and Andreas, E.L., 2000. Averaging Intervals For Spectral Analysis Of Nonstationary Turbulence. Boundary-Layer Meteorology, 95(2): 231-247. Finnigan, J.J., Clement, R., Malhi, Y., Leuning, R. and Cleugh, H.A., 2003. Re-evaluation of long-term flux measurement techniques. Part I: Averaging and coordinate rotation. Boundary-Layer Meteorology, 107(1): 1-48.

[Peruvian newborn fetal growth according to its sex, geographical area, and maternal parity and height].

PubMed

Rendón, Manuel Ticona; Apaza, Diana Huanco

2008-09-01

Birth weight is the most important indicator of fetal growth, fetal development, and nutritional estate of newborn, and several factors affect it. To know the fetal growth of Peruvian newborns according to fetal sex, maternal parity and height, and geographical area. Prospective and cross sectional study. Successive newborn data of 29 hospitals of Ministerio de Salud del Peru was obtained during 2005 year, all of them without intrauterine growth delay. Student ttest was used to compare: male and female, primiparous and multiparous, and coast, mountain, and rainforest newborn average weight (meaningful difference: p < 0.05). Maternal height was related to newborn weight, height, cephalic perimeter, and gestational age. From 50,568 selected alive newborns, male had an average weight from 19 to 41 g higher than female, and multiparous newborns had from 22 to 53 g more than primiparous newborns. Maternal height has a direct connection with newborn weight, height, and cephalic perimeter. Coast newborns had an average weight from 133 to 210 g higher than those from mountain, and from 76 to 142 g higher than those from rainforest; average weight of rainforest newborns was from 19 to 83 g higher to those from mountain. Weight differences due to fetal sex, maternal parity and height, and geographic region were meaningful among 36 to 42 weeks of gestation. Fetal sex, maternal parity and height, and geographical region affect newborn weight. It is recommended to use weight and gestational age as correction factors to appropriately classify Peruvian newborns.

Boys with a simple delayed puberty reach their target height.

PubMed

Cools, B L M; Rooman, R; Op De Beeck, L; Du Caju, M V L

2008-01-01

Final height in boys with delayed puberty is thought to be below target height. This conclusion, however, is based on studies that included patients with genetic short stature. We therefore studied final height in a group of 33 untreated boys with delayed puberty with a target height >-1.5 SDS. Standing height, sitting height, weight and arm span width were measured in each patient. Final height was predicted by the method of Greulich and Pyle using the tables of Bailey and Pinneau for retarded boys at their bone age (PAH1) and the tables of Bailey and Pinneau for average boys plus six months (PAH2). Mean final height (175.8 +/- 6.5 cm) was appropriate for the mean target height (174.7 +/- 4.5 cm). The prediction method of Bailey and Pinneau overestimated the final height by 1.4 cm and the modified prediction method slightly underestimated the final height (-0.15 cm). Boys with untreated delayed puberty reach a final height appropriate for their target height. Final height was best predicted by the method of Bailey and Pinneau using the tables for average boys at their bone age plus six months. Copyright 2008 S. Karger AG, Basel.

Comprehensive Evaluation of Fast-Response, Reynolds-Averaged Navier–Stokes, and Large-Eddy Simulation Methods Against High-Spatial-Resolution Wind-Tunnel Data in Step-Down Street Canyons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hayati, Arash Nemati; Stoll, Rob; Kim, J. J.

Three computational fluid dynamics (CFD) methods with different levels of flow-physics modelling are comprehensively evaluated against high-spatial-resolution wind-tunnel velocity data from step-down street canyons (i.e., a short building downwind of a tall building). The first method is a semi-empirical fast-response approach using the Quick Urban Industrial Complex (QUIC-URB) model. The second method solves the Reynolds-averaged Navier–Stokes (RANS) equations, and the third one utilizes a fully-coupled fluid-structure interaction large-eddy simulation (LES) model with a grid-turbulence inflow generator. Unlike typical point-by-point evaluation comparisons, here the entire two-dimensional wind-tunnel dataset is used to evaluate the dynamics of dominant flow topological features in themore » street canyon. Each CFD method is scrutinized for several geometric configurations by varying the downwind-to-upwind building-height ratio (H d/H u) and street canyon-width to building-width aspect ratio (S / W) for inflow winds perpendicular to the upwind building front face. Disparities between the numerical results and experimental data are quantified in terms of their ability to capture flow topological features for different geometric configurations. Ultimately, all three methods qualitatively predict the primary flow topological features, including a saddle point and a primary vortex. But, the secondary flow topological features, namely an in-canyon separation point and secondary vortices, are only well represented by the LES method despite its failure for taller downwind building cases. Misrepresentation of flow-regime transitions, exaggeration of the coherence of recirculation zones and wake fields, and overestimation of downwards vertical velocity into the canyon are the main defects in QUIC-URB, RANS and LES results, respectively. All three methods underestimate the updrafts and, surprisingly, QUIC-URB outperforms RANS for the streamwise velocity component, while RANS is superior to QUIC-URB for the vertical velocity component in the street canyon.« less

Comprehensive Evaluation of Fast-Response, Reynolds-Averaged Navier–Stokes, and Large-Eddy Simulation Methods Against High-Spatial-Resolution Wind-Tunnel Data in Step-Down Street Canyons

DOE PAGES

Hayati, Arash Nemati; Stoll, Rob; Kim, J. J.; ...

2017-05-18

Three computational fluid dynamics (CFD) methods with different levels of flow-physics modelling are comprehensively evaluated against high-spatial-resolution wind-tunnel velocity data from step-down street canyons (i.e., a short building downwind of a tall building). The first method is a semi-empirical fast-response approach using the Quick Urban Industrial Complex (QUIC-URB) model. The second method solves the Reynolds-averaged Navier–Stokes (RANS) equations, and the third one utilizes a fully-coupled fluid-structure interaction large-eddy simulation (LES) model with a grid-turbulence inflow generator. Unlike typical point-by-point evaluation comparisons, here the entire two-dimensional wind-tunnel dataset is used to evaluate the dynamics of dominant flow topological features in themore » street canyon. Each CFD method is scrutinized for several geometric configurations by varying the downwind-to-upwind building-height ratio (H d/H u) and street canyon-width to building-width aspect ratio (S / W) for inflow winds perpendicular to the upwind building front face. Disparities between the numerical results and experimental data are quantified in terms of their ability to capture flow topological features for different geometric configurations. Ultimately, all three methods qualitatively predict the primary flow topological features, including a saddle point and a primary vortex. But, the secondary flow topological features, namely an in-canyon separation point and secondary vortices, are only well represented by the LES method despite its failure for taller downwind building cases. Misrepresentation of flow-regime transitions, exaggeration of the coherence of recirculation zones and wake fields, and overestimation of downwards vertical velocity into the canyon are the main defects in QUIC-URB, RANS and LES results, respectively. All three methods underestimate the updrafts and, surprisingly, QUIC-URB outperforms RANS for the streamwise velocity component, while RANS is superior to QUIC-URB for the vertical velocity component in the street canyon.« less

Comprehensive Evaluation of Fast-Response, Reynolds-Averaged Navier-Stokes, and Large-Eddy Simulation Methods Against High-Spatial-Resolution Wind-Tunnel Data in Step-Down Street Canyons

NASA Astrophysics Data System (ADS)

Hayati, Arash Nemati; Stoll, Rob; Kim, J. J.; Harman, Todd; Nelson, Matthew A.; Brown, Michael J.; Pardyjak, Eric R.

2017-08-01

Three computational fluid dynamics (CFD) methods with different levels of flow-physics modelling are comprehensively evaluated against high-spatial-resolution wind-tunnel velocity data from step-down street canyons (i.e., a short building downwind of a tall building). The first method is a semi-empirical fast-response approach using the Quick Urban Industrial Complex (QUIC-URB) model. The second method solves the Reynolds-averaged Navier-Stokes (RANS) equations, and the third one utilizes a fully-coupled fluid-structure interaction large-eddy simulation (LES) model with a grid-turbulence inflow generator. Unlike typical point-by-point evaluation comparisons, here the entire two-dimensional wind-tunnel dataset is used to evaluate the dynamics of dominant flow topological features in the street canyon. Each CFD method is scrutinized for several geometric configurations by varying the downwind-to-upwind building-height ratio (H_d/H_u) and street canyon-width to building-width aspect ratio ( S / W) for inflow winds perpendicular to the upwind building front face. Disparities between the numerical results and experimental data are quantified in terms of their ability to capture flow topological features for different geometric configurations. Overall, all three methods qualitatively predict the primary flow topological features, including a saddle point and a primary vortex. However, the secondary flow topological features, namely an in-canyon separation point and secondary vortices, are only well represented by the LES method despite its failure for taller downwind building cases. Misrepresentation of flow-regime transitions, exaggeration of the coherence of recirculation zones and wake fields, and overestimation of downwards vertical velocity into the canyon are the main defects in QUIC-URB, RANS and LES results, respectively. All three methods underestimate the updrafts and, surprisingly, QUIC-URB outperforms RANS for the streamwise velocity component, while RANS is superior to QUIC-URB for the vertical velocity component in the street canyon.

Constructive systems, load-bearing and enclosing structures of high-rise buildings

NASA Astrophysics Data System (ADS)

Anatol'evna Korol', Elena; Olegovna Kustikova, Yuliya

2018-03-01

As the height of the building increases, loads on load-carrying structures increase dramatically, and as a result of the development of high-rise construction, several structural systems of such buildings have been developed: frame, frame-frame, cross-wall, barrel, box-type, box-to-wall ("pipe in pipe", "Trumpet in the farm"), etc. In turn, the barrel systems have their own versions: cantilever support of the ceilings on the trunk, suspension of the outer part of the overlap to the upper carrying console "hanging house" or its support by means of the walls on the lower bearing cantilever, intermediate position of the supporting cantilevers in height to the floor, from a part of floors. The object of the study are the structural solutions of high-rise buildings. The subject of the study is the layout of structural schemes of high-rise buildings, taking into account the main parameters - altitude (height), natural climatic conditions of construction, materials of structural elements and their physical and mechanical characteristics. The purpose of the study is to identify the features and systematization of structural systems of high-rise buildings and the corresponding structural elements. The results of the research make it possible, at the stage of making design decisions, to establish rational parameters for the correspondence between the structural systems of high-rise buildings and their individual elements.

Strategic guidelines for street canyon geometry to achieve sustainable street air quality—part II: multiple canopies and canyons

NASA Astrophysics Data System (ADS)

Chan, Andy T.; Au, William T. W.; So, Ellen S. P.

The flow field and pollutant dispersion characteristics in a three-dimensional urban street canyon are investigated for various building array geometries. The street canyon in consideration is located in a multi-canopy building array that is similar to realistic estate situations. The pollutant dispersion characteristics are studied for various canopy aspect ratios, namely: the canyon height to width ratio, canyon length to height ratio, canyon breadth ratio and crossroad locations are studied. A three-dimensional field-size canyon has been analysed through numerical simulations using k- ɛ turbulence model. As expected, the wind flow and mode of pollutant dispersion is strongly dependent on the various flow geometric configurations and that the results can be different from that of a single canyon system. For example, it is found that the pollutant retention value is minimum when the canyon height-to-width ratio is approximately 0.8, or that the building height ratio is 0.5. Various rules of thumbs on urban canyon geometry have been established for good pollutant dispersion.

Falls from height during the floor slab formwork of buildings: current situation in Spain.

PubMed

Adam, Jose M; Pallarés, Francisco J; Calderón, Pedro A

2009-01-01

One of the phases with the highest risk of falls from a height in the construction of a building is during the floor slab formwork stage. This paper analyzes this particular risk, as well as the most frequently used fall-protection systems. A survey was carried out to define the current situation in Spain with regard to falls from a height during floor slab formwork and the fall-protection systems used to prevent such a risk. The results of the survey clarified the current situation in Spain with regard to this risk, and made it clear that there is considerable risk of falling from a height during the floor slab formwork stage. All the safety systems analyzed presented a series of weak points that should be studied in detail before they can be used on building sites. The risk of falling associated with floor slab formwork and the most frequently used protection systems are analyzed. As no research had been carried out to date on this type of risk, we consider the research presented in this article to be a pioneer in the field.

Interior building details of Building D, Room DM5: mezzanine hallway, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior building details of Building D, Room D-M5: mezzanine hallway, intact historic asphalt surface flooring, full height partition wall with hoppers and east brick retaining wall with voids from the original veiling joist; southerly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

First Prismatic Building Model Reconstruction from Tomosar Point Clouds

NASA Astrophysics Data System (ADS)

Sun, Y.; Shahzad, M.; Zhu, X.

2016-06-01

This paper demonstrates for the first time the potential of explicitly modelling the individual roof surfaces to reconstruct 3-D prismatic building models using spaceborne tomographic synthetic aperture radar (TomoSAR) point clouds. The proposed approach is modular and works as follows: it first extracts the buildings via DSM generation and cutting-off the ground terrain. The DSM is smoothed using BM3D denoising method proposed in (Dabov et al., 2007) and a gradient map of the smoothed DSM is generated based on height jumps. Watershed segmentation is then adopted to oversegment the DSM into different regions. Subsequently, height and polygon complexity constrained merging is employed to refine (i.e., to reduce) the retrieved number of roof segments. Coarse outline of each roof segment is then reconstructed and later refined using quadtree based regularization plus zig-zag line simplification scheme. Finally, height is associated to each refined roof segment to obtain the 3-D prismatic model of the building. The proposed approach is illustrated and validated over a large building (convention center) in the city of Las Vegas using TomoSAR point clouds generated from a stack of 25 images using Tomo-GENESIS software developed at DLR.

Height-diameter equations for thirteen midwestern bottomland hardwood species

Treesearch

Kenneth C. Colbert; David R. Larsen; James R. Lootens

2002-01-01

Height-diameter equations are often used to predict the mean total tree height for trees when only diameter at breast height (dbh) is measured. Measuring dbh is much easier and is subject to less measurement error than total tree height. However, predicted heights only reflect the average height for trees of a particular diameter. In this study, we present a set of...

4. SOUTH SIDE OF BUILDING 2, (HANDBALL COURT ADDITION) SHOWING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. SOUTH SIDE OF BUILDING 2, (HANDBALL COURT ADDITION) SHOWING RELATIONSHIP WITH GARAGE ADDITION OF BUILDING 1. - Chollas Heights Naval Radio Transmitting Facility, Helix House, 6410 Zero Road, San Diego, San Diego County, CA

Effect of pillow height on the biomechanics of the head-neck complex: investigation of the cranio-cervical pressure and cervical spine alignment

PubMed Central

Yang, Hui; Zhou, Yan; Lin, Jin

2016-01-01

Background While appropriate pillow height is crucial to maintaining the quality of sleep and overall health, there are no universal, evidence-based guidelines for pillow design or selection. We aimed to evaluate the effect of pillow height on cranio-cervical pressure and cervical spine alignment. Methods Ten healthy subjects (five males) aged 26 ± 3.6 years were recruited. The average height, weight, and neck length were 167 ± 9.3 cm, 59.6 ± 11.9 kg, and 12.9 ± 1.2 cm respectively. The subjects lay on pillows of four different heights (H0, 110 mm; H1, 130 mm; H2, 150 mm; and H3, 170 mm). The cranio-cervical pressure distribution over the pillow was recorded; the peak and average pressures for each pillow height were compared by one-way ANOVA with repeated measures. Cervical spine alignment was studied using a finite element model constructed based on data from the Visible Human Project. The coordinate of the center of each cervical vertebra were predicted for each pillow height. Three spine alignment parameters (cervical angle, lordosis distance and kyphosis distance) were identified. Results The average cranial pressure at pillow height H3 was approximately 30% higher than that at H0, and significantly different from those at H1 and H2 (p < 0.05). The average cervical pressure at pillow height H0 was 65% lower than that at H3, and significantly different from those at H1 and H2 (p < 0.05). The peak cervical pressures at pillow heights H2 and H3 were significantly different from that at H0 (p < 0.05). With respect to cervical spine alignment, raising pillow height from H0 to H3 caused an increase of 66.4% and 25.1% in cervical angle and lordosis distance, respectively, and a reduction of 43.4% in kyphosis distance. Discussion Pillow height elevation significantly increased the average and peak pressures of the cranial and cervical regions, and increased the extension and lordosis of the cervical spine. The cranio-cervical pressures and cervical spine alignment were height-specific, and they were believed to reflect quality of sleep. Our results provide a quantitative and objective evaluation of the effect of pillow height on the biomechanics of the head-neck complex, and have application in pillow design and selection. PMID:27635354

Growth of hybrid poplars in Pennsylvania and Maryland clonal tests

Treesearch

Maurice E., Jr. Demeritt

1981-01-01

Average 4-year-height of 199 hybrid poplar clones ranged from 5.1 to 26.0 feet in Pennsylvania and 5.6 to 22.7 feet in Maryland. Several rapid-growing clones grew well at both locations, but height growth was affected by interactions of clones and location. The clones that grew best on both sites averaged 4 to 6 feet of height growth per year.

Health, Height, Height Shrinkage, and SES at Older Ages: Evidence from China†

PubMed Central

Huang, Wei; Lei, Xiaoyan; Ridder, Geert; Strauss, John

2015-01-01

In this paper, we build on the literature that examines associations between height and health outcomes of the elderly. We investigate the associations of height shrinkage at older ages with socioeconomic status, finding that height shrinkage for both men and women is negatively associated with better schooling, current urban residence, and household per capita expenditures. We then investigate the relationships between pre-shrinkage height, height shrinkage, and a rich set of health outcomes of older respondents, finding that height shrinkage is positively associated with poor health outcomes across a variety of outcomes, being especially strong for cognition outcomes. PMID:26594311

Scalar Fluxes Near a Tall Building in an Aligned Array of Rectangular Buildings

NASA Astrophysics Data System (ADS)

Fuka, Vladimír; Xie, Zheng-Tong; Castro, Ian P.; Hayden, Paul; Carpentieri, Matteo; Robins, Alan G.

2018-04-01

Scalar dispersion from ground-level sources in arrays of buildings is investigated using wind-tunnel measurements and large-eddy simulation (LES). An array of uniform-height buildings of equal dimensions and an array with an additional single tall building (wind tunnel) or a periodically repeated tall building (LES) are considered. The buildings in the array are aligned and form long streets. The sensitivity of the dispersion pattern to small changes in wind direction is demonstrated. Vertical scalar fluxes are decomposed into the advective and turbulent parts and the influences of wind direction and of the presence of the tall building on the scalar flux components are evaluated. In the uniform-height array turbulent scalar fluxes are dominant, whereas the tall building produces an increase of the magnitude of advective scalar fluxes that yields the largest component. The presence of the tall building causes either an increase or a decrease to the total vertical scalar flux depending on the position of the source with respect to the tall building. The results of the simulations can be used to develop parametrizations for street-canyon dispersion models and enhance their capabilities in areas with tall buildings.

Physical modeling of the atmospheric boundary layer in the UNH Flow Physics Facility

NASA Astrophysics Data System (ADS)

Taylor-Power, Gregory; Gilooly, Stephanie; Wosnik, Martin; Klewicki, Joe; Turner, John

2016-11-01

The Flow Physics Facility (FPF) at UNH has test section dimensions W =6.0m, H =2.7m, L =72m. It can achieve high Reynolds number boundary layers, enabling turbulent boundary layer, wind energy and wind engineering research with exceptional spatial and temporal instrument resolution. We examined the FPF's ability to experimentally simulate different types of the atmospheric boundary layer (ABL) using upstream roughness arrays. The American Society for Civil Engineers defines standards for simulating ABLs for different terrain types, from open sea to dense city areas (ASCE 49-12). The standards require the boundary layer to match a power law shape, roughness height, and power spectral density criteria. Each boundary layer type has a corresponding power law exponent and roughness height. The exponent and roughness height both increase with increasing roughness. A suburban boundary layer was chosen for simulation and a roughness element fetch was created. Several fetch lengths were experimented with and the resulting boundary layers were measured and compared to standards in ASCE 49-12: Wind Tunnel Testing for Buildings and Other Structures. Pitot tube and hot wire anemometers were used to measure average and fluctuating flow characteristics. Velocity profiles, turbulence intensity and velocity spectra were found to compare favorably.

5. WEST SIDE. VIEW FROM BUILDING 18 SHOWING SOUTH PORTION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. WEST SIDE. VIEW FROM BUILDING 18 SHOWING SOUTH PORTION OF BUILDING 22 WITH TALLER NORTH PORTION BEYOND.. - Chollas Heights Naval Radio Transmitting Facility, Public Works Shop, 6410 Zero Road, San Diego, San Diego County, CA

Oviposition and vertical dispersal of Aedes mosquitoes in multiple storey buildings in Colombo district, Sri Lanka.

PubMed

Jayathilake, T A Hasini D G; Wickramasinghe, Mervyn B; de Silva, B G D Nissanka K

2015-09-01

The Colombo City in Sri Lanka is experiencing tremendous development and construction of multiple storey buildings and high rise apartments. The change in housing types and microhabitats might have altered the flight and breeding behaviour of Aedes mosquito population. This study was carried out to determine the vertical dispersal and abundance of Aedes mosquitoes in multiple storey buildings in the Colombo district, with respect to abiotic factors such as rainfall, humidity and wind speed. Hence, this study is of paramount importance, particularly for planning and implementation of control measures against Aedes mosquitoes. An ovitrap based study was carried out at four selected multiple storey buildings in four residential areas located in Colombo, Sri Lanka, from August to December 2013. Results were analyzed using four indices; ovitrap index, mean number of larvae, mean number of eggs and mean number of larvae per ovipaddle. The results implied that Aedes mosquitoes could be found in different elevations from ground floor to the highest floor (130 ft). There was a significant difference between height and ovitrap index (p<0.05), and height and mean number of larvae per recovered ovipaddle (p<0.05). The highest index value for mean number of eggs was observed as 3.492 ± 0.655 at the 6th floor (60 ft high from ground level). At the same height (60 ft height) other indices (ovitrap index, mean number of larvae and mean number of larvae per ovipaddle) also displayed higher values, i.e. 13.19 ± 2.98%, 1.366 ± 0.527, and 2.070 ± 0.421%, respectively. Abiotic factors such as wind speed, coastal nature, etc. displayed a significant effect to the vertical dispersal of Aedes mosquitoes (p<0.05). The study suggested that Aedes mosquitoes are able to breed at any level of the buildings and not restricted by their height. The indices (mean number of larvae, mean number of eggs) representing the vertical dispersal with respect to abundance seemed to be statistically non-significant (p>0.05) with height which indicates high abundance of Aedes mosquitoes at higher floors. Abiotic factors also seemed to cause significant effect to the vertical dispersal of Aedes mosquitoes in high rise buildings.

Assessment of Historic Concrete and Masonry by Broadband Vibration Testing

DTIC Science & Technology

2010-08-01

a number of different tests conducted on components of historic buildings at Wright-Patterson AFB, OH. The buildings, currently designated ... testing along the height, the pier is considered to behave as a rod. The pedestals have designations N (north) or S (south), and are numbered from...that were tested in each panel. Each location is designated by its height, 1, 2, 3, 5, 7, or 9 feet above grade, and by its horizontal location

Height, weight and body mass index values of mid-19th century New York legislative officers.

PubMed

Bodenhorn, Howard

2010-07-01

Previous studies of mid-19th century American heights and body mass index values have used potentially unrepresentative groups-students in military academies, prisoners, and African Americans. This paper uses an alternative source with heights and weights of ordinary people employed in a wide variety of occupations. The results reveal the operation of the antebellum paradox in that average heights declined between men born circa 1820 and those born circa 1840. Average weights also declined for adult males, suggesting a decline in mid-19th century nutritional status. 2010 Elsevier B.V. All rights reserved.

Height restoration and maintenance after treating unstable osteoporotic vertebral compression fractures by cement augmentation is dependent on the cement volume used.

PubMed

Krüger, Antonio; Baroud, Gamal; Noriega, David; Figiel, Jens; Dorschel, Christine; Ruchholtz, Steffen; Oberkircher, Ludwig

2013-08-01

Two different procedures, used for percutaneous augmentation of vertebral compression fractures were compared, with respect to height restoration and maintenance after cyclic loading. Additionally the impact of the cement volume used was investigated. Wedge compression fractures were created in 36 human cadavaric vertebrae (T10-L3). Twenty-seven vertebrae were treated with the SpineJack® with different cement volumes (maximum, intermediate, and no cement), and 9 vertebrae were treated with Balloon Kyphoplasty. Vertebral heights were measured pre- and postfracture as well as after treatment and loading. Cyclic loading was performed with 10,000cycles (1Hz, 100-600N). The average anterior height after restoration was 85.56% for Kyphoplasty; 96.20% for SpineJack® no cement; 93.44% for SpineJack® maximum and 96% for the SpineJack® intermediate group. The average central height after restoration was 93.89% for Kyphoplasty; 100.20% for SpineJack® no cement; 99.56% for SpineJack® maximum and 101.13% for the SpineJack® intermediate group. The average anterior height after cyclic loading was 85.33 % for Kyphoplasty; 87.30% in the SpineJack® no cement, 92% in the SpineJack® maximum and 87% in the SpineJack® intermediate group. The average central height after cyclic loading was 92% for Kyphoplasty; 93.80% in the SpineJack® no cement; 98.56% in the SpineJack® maximum and 94.25% in the SpineJack® intermediate group. Height restoration was significantly better for the SpineJack® group compared to Kyphoplasty. Height maintenance was dependent on the cement volume used. The group with the SpineJack® without cement nevertheless showed better results in height maintenance, yet the statistical significance could not be demonstrated. Copyright © 2013 Elsevier Ltd. All rights reserved.

First-Year Growth and Survival Of Long Cottonwood Cuttings

Treesearch

W.K. Randall; R.M. Krinard

1977-01-01

When five Stoneville cottonwood clones were grown in a nursery for one season, lifted with about a foot of root, and planted in 3-foot deep holes, they averaged 9.6 feet in height growth and 92 percent survival after 1 year in the field. Planted height averaged 8.3 feet. The same clonal material planted without roots averaged only 36 percent survival. These results...

Control of bed height in a fluidized bed gasification system

DOEpatents

Mehta, Gautam I.; Rogers, Lynn M.

1983-12-20

In a fluidized bed apparatus a method for controlling the height of the fdized bed, taking into account variations in the density of the bed. The method comprises taking simultaneous differential pressure measurements at different vertical elevations within the vessel, averaging the differential pressures, determining an average fluidized bed density, then periodically calculating a weighting factor. The weighting factor is used in the determination of the actual bed height which is used in controlling the fluidizing means.

Experimental Study on Tsunami Risk Reduction on Coastal Building Fronted by Sea Wall

PubMed Central

Khan, M. T. R.; Shirazi, S. M.

2014-01-01

This experimental study was conducted to idealize the efficacy of sea wall in controlling the tsunami forces on onshore structures. Different types of sea walls were placed in front of the building model. The tsunami forces and the wave heights were measured with and without the sea wall conditions. Types of sea wall, wall height, and wall positions were varied simultaneously to quantify the force reductions. Maximum of 41% forces was reduced by higher sea wall, positioned closer proximity to the model whereas this reduction was about 27% when the wall height was half of the high wall. Experimental investigations revealed that wall with adequate height and placed closer to the structures enables a satisfactory predictor of the force reduction on onshore structures. Another set of tests were performed with perforated wall placing near the building model. Less construction cost makes the provision of perforated sea wall interesting. The overall results showed that the efficacy of perforated wall is almost similar to solid wall. Hence, it can be efficiently used instead of solid wall. Moreover, overtopped water that is stuck behind the wall is readily gone back to the sea through perforations releasing additional forces on the nearby structures. PMID:24790578

Scaling Constraints in Junior Tennis: The Influence of Net Height on Skilled Players' Match-Play Performance

ERIC Educational Resources Information Center

Limpens, Vera; Buszard, Tim; Shoemaker, Emma; Savelsbergh, Geert J. P.; Reid, Machar

2018-01-01

Purpose: The net height in tennis (0.91 m) is approximately 50% of a professional tennis player's height. Children are also expected to play with this net height, even though it is approximately 70% of the average 10-year-old's height. This study examined the immediate effect of lowering net height on the performance characteristics of skilled…

Evolution of nesting height in an endangered Hawaiian forest bird in response to a non-native predator.

PubMed

Vanderwerf, Eric A

2012-10-01

The majority of bird extinctions since 1800 have occurred on islands, and non-native predators have been the greatest threat to the persistence of island birds. Island endemic species often lack life-history traits and behaviors that reduce the probability of predation and they can become evolutionarily trapped if they are unable to adapt, but few studies have examined the ability of island species to respond to novel predators. The greatest threat to the persistence of the Oahu Elepaio (Chasiempis ibidis), an endangered Hawaiian forest bird, is nest predation by non-native black rats (Rattus rattus). I examined whether Oahu Elepaio nest placement has changed at the individual and population levels in response to rat predation by measuring nest height and determining whether each nest produced offspring from 1996 to 2011. Average height of Oahu Elepaio nests increased 50% over this 16-year period, from 7.9 m (SE 1.7) to 12.0 m (SE 1.1). There was no net change in height of sequential nests made by individual birds, which means individual elepaios have not learned to place nests higher. Nests ≤3 m off the ground produced offspring less often, and the proportion of such nests declined over time, which suggests that nest-building behavior has evolved through natural selection by predation. Nest success increased over time, which may increase the probability of long-term persistence of the species. Rat control may facilitate the evolution of nesting height by slowing the rate of population decline and providing time for this adaptive response to spread through the population. ©2012 Society for Conservation Biology.

47 CFR 73.614 - Power and antenna height requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Power and antenna height requirements. 73.614... RADIO BROADCAST SERVICES Television Broadcast Stations § 73.614 Power and antenna height requirements.... No minimum antenna height above average terrain is specified. (b) Maximum power. Applications will...

47 CFR 73.614 - Power and antenna height requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Power and antenna height requirements. 73.614... RADIO BROADCAST SERVICES Television Broadcast Stations § 73.614 Power and antenna height requirements.... No minimum antenna height above average terrain is specified. (b) Maximum power. Applications will...

47 CFR 73.614 - Power and antenna height requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Power and antenna height requirements. 73.614... RADIO BROADCAST SERVICES Television Broadcast Stations § 73.614 Power and antenna height requirements.... No minimum antenna height above average terrain is specified. (b) Maximum power. Applications will...

47 CFR 73.614 - Power and antenna height requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Power and antenna height requirements. 73.614... RADIO BROADCAST SERVICES Television Broadcast Stations § 73.614 Power and antenna height requirements.... No minimum antenna height above average terrain is specified. (b) Maximum power. Applications will...

47 CFR 73.614 - Power and antenna height requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Power and antenna height requirements. 73.614... RADIO BROADCAST SERVICES Television Broadcast Stations § 73.614 Power and antenna height requirements.... No minimum antenna height above average terrain is specified. (b) Maximum power. Applications will...

Climate-sensitive urban design through Envi-Met simulation: case study in Kemayoran, Jakarta

NASA Astrophysics Data System (ADS)

Kusumastuty, K. D.; Poerbo, H. W.; Koerniawan, M. D.

2018-03-01

Indonesia as a tropical country which the character of its climate are hot and humid, the outdoor activity applications are often disrupted due to discomfort in thermal conditions. Massive construction of skyscrapers in urban areas are caused by the increase of human population leads to reduced green and infiltration areas that impact to environmental imbalances and triggering microclimate changes with rising air temperatures on the surface. The area that significantly experiences the rise of temperature in the Central Business District (CBD), which has need an analysis to create thermal comfort conditions to improve the ease of outdoor activities by an approach. This study aims to design the Kemayoran CBD through Climate Sensitive Urban Design especially in hot and humid tropical climate area and analyze thermal comfort level and optimal air conditioning in the outdoor area. This research used a quantitative method by generating the design using Climate Sensitive Urban Design principle through Envi-met 4.1 simulation program to find out the value of PMV, air temperature, wind speed and relative humidity conditions. The design area considers the configuration of buildings such as the distance between buildings, the average height, the orientation of the building, and the width of the road.

Impact of roof height non-uniformity on pollutant transport between a street canyon and intersections.

PubMed

Nosek, Štěpán; Kukačka, Libor; Jurčáková, Klára; Kellnerová, Radka; Jaňour, Zbyněk

2017-08-01

This paper presents an extension of our previous wind-tunnel study (Nosek et al., 2016) in which we highlighted the need for investigation of the removal mechanisms of traffic pollution from all openings of a 3D street canyon. The extension represents the pollution flux (turbulent and advective) measurements at the lateral openings of three different 3D street canyons for the winds perpendicular and oblique to the along-canyon axis. The pollution was simulated by emitting a passive gas (ethane) from a homogeneous ground-level line source positioned along the centreline of the investigated street canyons. The street canyons were formed by courtyard-type buildings of two different regular urban-array models. The first model has a uniform building roof height, while the second model has a non-uniform roof height along each building's wall. The mean flow and concentration fields at the canyons' lateral openings confirm the findings of other studies that the buildings' roof-height variability at the intersections plays an important role in the dispersion of the traffic pollutants within the canyons. For the perpendicular wind, the non-uniform roof-height canyon appreciably removes or entrains the pollutant through its lateral openings, contrary to the uniform canyon, where the pollutant was removed primarily through the top. The analysis of the turbulent mass transport revealed that the coherent flow structures of the lateral momentum transport correlate with the ventilation processes at the lateral openings of all studied canyons. These flow structures coincide at the same areas and hence simultaneously transport the pollutant in opposite directions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of canyon geometry on the distribution of traffic-related air pollution in a large urban area: Implications of a multi-canyon air pollution dispersion model

NASA Astrophysics Data System (ADS)

Fu, Xiangwen; Liu, Junfeng; Ban-Weiss, George A.; Zhang, Jiachen; Huang, Xin; Ouyang, Bin; Popoola, Olalekan; Tao, Shu

2017-09-01

Street canyons are ubiquitous in urban areas. Traffic-related air pollutants in street canyons can adversely affect human health. In this study, an urban-scale traffic pollution dispersion model is developed considering street distribution, canyon geometry, background meteorology, traffic assignment, traffic emissions and air pollutant dispersion. In the model, vehicle exhausts generated from traffic flows first disperse inside street canyons along the micro-scale wind field generated by computational fluid dynamics (CFD) model. Then, pollutants leave the street canyon and further disperse over the urban area. On the basis of this model, the effects of canyon geometry on the distribution of NOx and CO from traffic emissions were studied over the center of Beijing. We found that an increase in building height leads to heavier pollution inside canyons and lower pollution outside canyons at pedestrian level, resulting in higher domain-averaged concentrations over the area. In addition, canyons with highly even or highly uneven building heights on each side of the street tend to lower the urban-scale air pollution concentrations at pedestrian level. Further, increasing street widths tends to lead to lower pollutant concentrations by reducing emissions and enhancing ventilation simultaneously. Our results indicate that canyon geometry strongly influences human exposure to traffic pollutants in the populated urban area. Carefully planning street layout and canyon geometry while considering traffic demand as well as local weather patterns may significantly reduce inhalation of unhealthy air by urban residents.

Wind interference effect on an octagonal plan shaped tall building due to square plan shaped tall buildings

NASA Astrophysics Data System (ADS)

Kar, Rony; Dalui, Sujit Kumar

2016-03-01

The variation of pressure at the faces of the octagonal plan shaped tall building due to interference of three square plan shaped tall building of same height is analysed by computational fluid dynamics module, namely ANSYS CFX for 0° wind incidence angle only. All the buildings are closely spaced (distance between two buildings varies from 0.4 h to 2 h, where h is the height of the building). Different cases depending upon the various positions of the square plan shaped buildings are analysed and compared with the octagonal plan shaped building in isolated condition. The comparison is presented in the form of interference factors (IF) and IF contours. Abnormal pressure distribution is observed in some cases. Shielding and channelling effect on the octagonal plan shaped building due to the presence of the interfering buildings are also noted. In the interfering condition the pressure distribution at the faces of the octagonal plan shaped building is not predictable. As the distance between the principal octagonal plan shaped building and the third square plan shaped interfering building increases the behaviour of faces becomes more systematic. The coefficient of pressure (C p) for each face of the octagonal plan shaped building in each interfering case can be easily found if we multiply the IF with the C p in the isolated case.

Spatial and Temporal scales of time-averaged 700 MB height anomalies

NASA Technical Reports Server (NTRS)

Gutzler, D.

1981-01-01

The monthly and seasonal forecasting technique is based to a large extent on the extrapolation of trends in the positions of the centers of time averaged geopotential height anomalies. The complete forecasted height pattern is subsequently drawn around the forecasted anomaly centers. The efficacy of this technique was tested and time series of observed monthly mean and 5 day mean 700 mb geopotential heights were examined. Autocorrelation statistics are generated to document the tendency for persistence of anomalies. These statistics are compared to a red noise hypothesis to check for evidence of possible preferred time scales of persistence. Space-time spectral analyses at middle latitudes are checked for evidence of periodicities which could be associated with predictable month-to-month trends. A local measure of the average spatial scale of anomalies is devised for guidance in the completion of the anomaly pattern around the forecasted centers.

Multi-dimensional SAR tomography for monitoring the deformation of newly built concrete buildings

NASA Astrophysics Data System (ADS)

Ma, Peifeng; Lin, Hui; Lan, Hengxing; Chen, Fulong

2015-08-01

Deformation often occurs in buildings at early ages, and the constant inspection of deformation is of significant importance to discover possible cracking and avoid wall failure. This paper exploits the multi-dimensional SAR tomography technique to monitor the deformation performances of two newly built buildings (B1 and B2) with a special focus on the effects of concrete creep and shrinkage. To separate the nonlinear thermal expansion from total deformations, the extended 4-D SAR technique is exploited. The thermal map estimated from 44 TerraSAR-X images demonstrates that the derived thermal amplitude is highly related to the building height due to the upward accumulative effect of thermal expansion. The linear deformation velocity map reveals that B1 is subject to settlement during the construction period, in addition, the creep and shrinkage of B1 lead to wall shortening that is a height-dependent movement in the downward direction, and the asymmetrical creep of B2 triggers wall deflection that is a height-dependent movement in the deflection direction. It is also validated that the extended 4-D SAR can rectify the bias of estimated wall shortening and wall deflection by 4-D SAR.

Intralocus sexual conflict over human height

PubMed Central

Stulp, Gert; Kuijper, Bram; Buunk, Abraham P.; Pollet, Thomas V.; Verhulst, Simon

2012-01-01

Intralocus sexual conflict (IASC) occurs when a trait under selection in one sex constrains the other sex from achieving its sex-specific fitness optimum. Selection pressures on body size often differ between the sexes across many species, including humans: among men individuals of average height enjoy the highest reproductive success, while shorter women have the highest reproductive success. Given its high heritability, IASC over human height is likely. Using data from sibling pairs from the Wisconsin Longitudinal Study, we present evidence for IASC over height: in shorter sibling pairs (relatively) more reproductive success (number of children) was obtained through the sister than through the brother of the sibling pair. By contrast, in average height sibling pairs most reproductive success was obtained through the brother relative to the sister. In conclusion, we show that IASC over a heritable, sexually dimorphic physical trait (human height) affects Darwinian fitness in a contemporary human population. PMID:22875819

Formation, distribution and variability in snow cover on the Asian territory of the USSR

NASA Technical Reports Server (NTRS)

Pupkov, V. N.

1985-01-01

A description is given of maps compiled for annual and average multiple-year water reserves. The annual and average multiple-year maximum snow cover height for winter, extreme values of maximum snow reserves, and the average height and snow reserves at the end of each decade are shown. These maps were made for the entire Asian territory of the USSR, excluding Central Asia, Kamchatka Peninsula, and the Sakhalin Islands.

A new method of building footprints detection using airborne laser scanning data and multispectral image

NASA Astrophysics Data System (ADS)

Luo, Yiping; Jiang, Ting; Gao, Shengli; Wang, Xin

2010-10-01

It presents a new approach for detecting building footprints in a combination of registered aerial image with multispectral bands and airborne laser scanning data synchronously obtained by Leica-Geosystems ALS40 and Applanix DACS-301 on the same platform. A two-step method for building detection was presented consisting of selecting 'building' candidate points and then classifying candidate points. A digital surface model(DSM) derived from last pulse laser scanning data was first filtered and the laser points were classified into classes 'ground' and 'building or tree' based on mathematic morphological filter. Then, 'ground' points were resample into digital elevation model(DEM), and a Normalized DSM(nDSM) was generated from DEM and DSM. The candidate points were selected from 'building or tree' points by height value and area threshold in nDSM. The candidate points were further classified into building points and tree points by using the support vector machines(SVM) classification method. Two classification tests were carried out using features only from laser scanning data and associated features from two input data sources. The features included height, height finite difference, RGB bands value, and so on. The RGB value of points was acquired by matching laser scanning data and image using collinear equation. The features of training points were presented as input data for SVM classification method, and cross validation was used to select best classification parameters. The determinant function could be constructed by the classification parameters and the class of candidate points was determined by determinant function. The result showed that associated features from two input data sources were superior to features only from laser scanning data. The accuracy of more than 90% was achieved for buildings in first kind of features.

Photographic copy of architectural drawing (original drawing located at the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of architectural drawing (original drawing located at the Panama Canal Commission Headquarters Building, Department of Engineering Vault, Balboa Heights, Republic of Panama). Rear elevation. - Quarry Heights, Officers' Quarters, Parkinson Lane, Balboa, Former Panama Canal Zone, CZ

Photographic copy of architectural drawing (original drawing located at the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of architectural drawing (original drawing located at the Panama Canal Commission Headquarters Building, Department of Engineering Vault, Balboa Heights, Republic of Panama). Longitudinal section. - Quarry Heights, Officers' Quarters, Parkinson Lane, Balboa, Former Panama Canal Zone, CZ

Photographic copy of architectural drawing (original drawing located at the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of architectural drawing (original drawing located at the Panama Canal Commission Headquarters Building, Department of Engineering Vault, Balboa Heights, Republic of Panama). First floor plan. - Quarry Heights, Officers' Quarters, Parkinson Lane, Balboa, Former Panama Canal Zone, CZ

Photographic copy of architectural drawing (original drawing located at the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of architectural drawing (original drawing located at the Panama Canal Commission Headquarters Building, Department of Engineering Vault, Balboa Heights, Republic of Panama). Front elevation. - Quarry Heights, Officers' Quarters, Parkinson Lane, Balboa, Former Panama Canal Zone, CZ

Photographic copy of architectural drawing (original drawing located at the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of architectural drawing (original drawing located at the Panama Canal Commission Headquarters Building, Department of Engineering Vault, Balboa Heights, Republic of Panama). Left side elevation. - Quarry Heights, Officers' Quarters, Parkinson Lane, Balboa, Former Panama Canal Zone, CZ

Photographic copy of architectural drawing (original drawing located at the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of architectural drawing (original drawing located at the Panama Canal Commission Headquarters Building, Department of Engineering Vault, Balboa Heights, Republic of Panama), Right side elevation. - Quarry Heights, Officers' Quarters, Parkinson Lane, Balboa, Former Panama Canal Zone, CZ

Photographic copy of architectural drawing (original drawing located at the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of architectural drawing (original drawing located at the Panama Canal Commission Headquarters Building, Department of Engineering Vault, Balboa Heights, Republic of Panama). Second floor plan. - Quarry Heights, Officers' Quarters, Parkinson Lane, Balboa, Former Panama Canal Zone, CZ

31. DETAIL OF OVERHEAD TENSIONER DEVICE LOCATED ABOVE SOUTHERN DOOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. DETAIL OF OVERHEAD TENSIONER DEVICE LOCATED ABOVE SOUTHERN DOOR OF BUILDING 1. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

The ratio of effective building height to street width governs dispersion of local vehicle emissions

NASA Astrophysics Data System (ADS)

Schulte, Nico; Tan, Si; Venkatram, Akula

2015-07-01

Analysis of data collected in street canyons located in Hanover, Germany and Los Angeles, USA, suggests that street-level concentrations of vehicle-related pollutants can be estimated with a model that assumes that vertical turbulent transport of emissions dominates the governing processes. The dispersion model relates surface concentrations to traffic flow rate, the effective aspect ratio of the street, and roof level turbulence. The dispersion model indicates that magnification of concentrations relative to those in the absence of buildings is most sensitive to the aspect ratio of the street, which is the ratio of the effective height of the buildings on the street to the width of the street. This result can be useful in the design of transit oriented developments that increase building density to reduce emissions from transportation.

[Nutritional evaluation of adolescent students from Extremadura based on anthropometric measurements].

PubMed

Fernández Cabrera, Jacinta; Aranda Medina, Emilio; Córdoba Ramos, María de Guía; Hernández León, Alejandro; Rodríguez Bernabé, José Antonio; Pérez-Nevado, Francisco

2014-03-01

Nutrition is one of the pillars for proper body development and optimal nutritional status. Anthropometric methods are most commonly used for body composition analysis and are an essential part in the assessment of the nutritional status of individuals and population groups. This study aims to assess the nutritional status of adolescents from Extremadura (Spain); to determine variations in body composition according to the percentiles obtained; and to propose these values as a reference to the nutritional status of the adolescent population in Extremadura. A cross sectional study in the community of Extremadura was performed, including a total of 816 students of Secondary School Education of both sexes; and of all ages in the adolescence stage. The selected secondary schools belonged to populations of different sizes (less than 5,000 to more than 60,000 inhabitants). From the measurements taken, different anthropometric indices were determined and the percentiles 3, 10, 25, 50, 75, 90, 95 and 97 for weight, height and complexion were found. There were significant gender differences for height, weight, triceps skinfold, arm muscle area and arm fat area. Boys showed greater figures for height, weight and arm muscle area; however, the triceps skinfold and arm fat area was higher in girls. When compared to other national studies, the average height of our population was lower by about 3 cm in both sexes; the average weight was similar, but our adolescents had a higher proportion of fat in the arm. Extremadura girls seem to have a faster growth, reaching final height at an earlier age than the national average, although this height is below average. The boys had a continuous growth in all ages, maintaining national averages. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

47 CFR 73.211 - Power and antenna height requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Power and antenna height requirements. 73.211... RADIO BROADCAST SERVICES FM Broadcast Stations § 73.211 Power and antenna height requirements. (a... Class C and C0 stations is 100 kW. (2) Class C0 stations must have an antenna height above average...

47 CFR 73.211 - Power and antenna height requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Power and antenna height requirements. 73.211... RADIO BROADCAST SERVICES FM Broadcast Stations § 73.211 Power and antenna height requirements. (a... Class C and C0 stations is 100 kW. (2) Class C0 stations must have an antenna height above average...

47 CFR 73.211 - Power and antenna height requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Power and antenna height requirements. 73.211... RADIO BROADCAST SERVICES FM Broadcast Stations § 73.211 Power and antenna height requirements. (a... Class C and C0 stations is 100 kW. (2) Class C0 stations must have an antenna height above average...

47 CFR 73.211 - Power and antenna height requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Power and antenna height requirements. 73.211... RADIO BROADCAST SERVICES FM Broadcast Stations § 73.211 Power and antenna height requirements. (a... Class C and C0 stations is 100 kW. (2) Class C0 stations must have an antenna height above average...

47 CFR 73.211 - Power and antenna height requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Power and antenna height requirements. 73.211... RADIO BROADCAST SERVICES FM Broadcast Stations § 73.211 Power and antenna height requirements. (a... Class C and C0 stations is 100 kW. (2) Class C0 stations must have an antenna height above average...

Characterization of pollutant dispersion near elongated buildings based on wind tunnel simulations

NASA Astrophysics Data System (ADS)

Perry, S. G.; Heist, D. K.; Brouwer, L. H.; Monbureau, E. M.; Brixey, L. A.

2016-10-01

This paper presents a wind tunnel study of the effects of elongated rectangular buildings on the dispersion of pollutants from nearby stacks. The study examines the influence of source location, building aspect ratio, and wind direction on pollutant dispersion with the goal of developing improved algorithms within dispersion models. The paper also examines the current AERMOD/PRIME modeling capabilities compared to wind tunnel observations. Differences in the amount of plume material entrained in the wake region downwind of a building for various source locations and source heights are illustrated with vertical and lateral concentration profiles. These profiles were parameterized using the Gaussian equation and show the influence of building/source configurations on those parameters. When the building is oriented at 45° to the approach flow, for example, the effective plume height descends more rapidly than it does for a perpendicular building, enhancing the resulting surface concentrations in the wake region. Buildings at angles to the wind cause a cross-wind shift in the location of the plume resulting from a lateral mean flow established in the building wake. These and other effects that are not well represented in many dispersion models are important considerations when developing improved algorithms to estimate the location and magnitude of concentrations downwind of elongated buildings.

Photographic copy of architectural drawing (original drawing located at the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of architectural drawing (original drawing located at the Panama Canal Commission Headquarters Building, Department of Engineering Vault, Balboa Heights, Republic of Panama). Details of bookshelves and pilasters. - Quarry Heights, Officers' Quarters, Parkinson Lane, Balboa, Former Panama Canal Zone, CZ

[The secular trend in body height and weight in the adult population in the Czech republic].

PubMed

Kopecký, Miroslav; Kikalová, Kateřina; Charamza, Jiří

Secular changes in anthropometric parameters reflect the effect of socio-economic conditions in interaction with other factors on individuals in the course of 100-200 years. The main aim of the research was to determine the average body height and weight for the current adult population of men 19 to 94 years old and women 19 to 86 years old in the Czech Republic, and to compare the average values ​​of body height and weight of the monitored group with the reference values ​​for the adult population observed in our country from 1895 to 2001.Body height and weight were measured with standard anthropometry in 973 men aged 19-94 years and 2,606 women aged 19-86 years. The research was carried out from 2013 to 2015. Statistical tests: t-test, one-way analysis of variance (ANOVA). The average body weight and height of the current adult male is 178.58 cm and 80.86 kg, and of adult female 165.99 cm and 65.67 kg. When compared to men, women show significantly lower average height by 12.59 cm and lower weight by 15.19 kg. The results show that men today are about 10.61 cm higher and weigh 9.01 kilograms more than men in 1895. Todays women are about 9.43 centimeters taller, but weigh 0,58 kg less than women of the same age in 1895.Comparison of results from 1895 to 2015 shows that at present there is likely stagnation or decline in the positive secular trend in body height among men and women. The weight of men is increasing while there is stagnation in the body weight of women.

Increases of Chamber Height and Base Diameter Have Contrasting Effects on Grazing Rate of Two Cladoceran Species: Implications for Microcosm Studies.

PubMed

Pan, Ying; Zhang, Yunshu; Peng, Yan; Zhao, Qinghua; Sun, Shucun

2015-01-01

Aquatic microcosm studies often increase either chamber height or base diameter (to increase water volume) to test spatial ecology theories such as "scale" effects on ecological processes, but it is unclear whether the increase of chamber height or base diameter have the same effect on the processes, i.e., whether the effect of the shape of three-dimensional spaces is significant. We orthogonally manipulated chamber height and base diameter and determined swimming activity, average swimming velocity and grazing rates of the cladocerans Daphnia magna and Moina micrura (on two algae Scenedesmus quadricauda and Chlorella vulgaris; leading to four aquatic algae-cladoceran systems in total) under different microcosm conditions. Across all the four aquatic systems, increasing chamber height at a given base diameter significantly decreased the duration and velocity of horizontal swimming, and it tended to increase the duration but decrease the velocity of vertical swimming. These collectively led to decreases in both average swimming velocity and grazing rate of the cladocerans in the tall chambers (at a given base diameter), in accordance with the positive relationship between average swimming velocity and grazing rate. In contrast, an increase of base diameter at a given chamber height showed contrasting effects on the above parameters. Consistently, at a given chamber volume increasing ratio of chamber height to base diameter decreased the average swimming velocity and grazing rate across all the aquatic systems. In general, increasing chamber depth and base diameter may exert contrasting effects on zooplankton behavior and thus phytoplankton-zooplankton interactions. We suggest that spatial shape plays an important role in determining ecological process and thus should be considered in a theoretical framework of spatial ecology and also the physical setting of aquatic microcosm experiments.

Increases of Chamber Height and Base Diameter Have Contrasting Effects on Grazing Rate of Two Cladoceran Species: Implications for Microcosm Studies

PubMed Central

Pan, Ying; Zhang, Yunshu; Peng, Yan; Zhao, Qinghua; Sun, Shucun

2015-01-01

Aquatic microcosm studies often increase either chamber height or base diameter (to increase water volume) to test spatial ecology theories such as “scale” effects on ecological processes, but it is unclear whether the increase of chamber height or base diameter have the same effect on the processes, i.e., whether the effect of the shape of three-dimensional spaces is significant. We orthogonally manipulated chamber height and base diameter and determined swimming activity, average swimming velocity and grazing rates of the cladocerans Daphnia magna and Moina micrura (on two algae Scenedesmus quadricauda and Chlorella vulgaris; leading to four aquatic algae-cladoceran systems in total) under different microcosm conditions. Across all the four aquatic systems, increasing chamber height at a given base diameter significantly decreased the duration and velocity of horizontal swimming, and it tended to increase the duration but decrease the velocity of vertical swimming. These collectively led to decreases in both average swimming velocity and grazing rate of the cladocerans in the tall chambers (at a given base diameter), in accordance with the positive relationship between average swimming velocity and grazing rate. In contrast, an increase of base diameter at a given chamber height showed contrasting effects on the above parameters. Consistently, at a given chamber volume increasing ratio of chamber height to base diameter decreased the average swimming velocity and grazing rate across all the aquatic systems. In general, increasing chamber depth and base diameter may exert contrasting effects on zooplankton behavior and thus phytoplankton-zooplankton interactions. We suggest that spatial shape plays an important role in determining ecological process and thus should be considered in a theoretical framework of spatial ecology and also the physical setting of aquatic microcosm experiments. PMID:26273836

The Educational Aspects of Obesity.

ERIC Educational Resources Information Center

Kaufmann, David A.

A traditional discussion of obesity considers the number of pounds over what is considered average for one's age, height, and sex, and is based on the assumption that the average weight for a given group of people of the same age, height, and sex is the healthiest status for that group. There is a physiological and biochemical basis for obesity.…

Planted Pines do not Respond to Bedding on an Acadia-Beauregard-Kolin Silt Loam Site

Treesearch

James D. Haywood

1980-01-01

Average height and volume of loblolly and slash pines were not affected by site treatment or soil differences 15 years after planting on an Acadia-Beauregard-Kolin silt loam site. Slash pine averaged 2.04 m more in height and yielded 22 percent more volume per hectare than did loblolly pine.

The Use of Arm Span as a Substitute for Height in Calculating Body Mass Index (BMI) for Spine Deformity Patients.

PubMed

Opoku, Harriet; Yirerong, Theresa; Osei-Onwona, Belinda; Boachie-Adjei, Oheneba

To compare arm span and height in body mass index (BMI) calculation in patients with spinal curvature and investigate their impact on interpretation of BMI. Prospective case-control cohorts. The BMI value is based on weight to height ratio. Spine deformity patients experience height loss and its use in calculating BMI is likely to produce errors. A surrogate for height should therefore be sought in BMI determination. Ninety-three spine deformity patients were matched with 64 normal children. Anthropometric values (height, arm span, and weight) and spinal curve were obtained. BMIs using arm span and height were calculated, and statistical analysis performed to assess the relationship between BMI/height and BMI/arm span in both groups as well as the relationship between these values and Arm Span to Height difference (Delta AH). There were 46 males and 47 females, the average age was 15.5 years in Group 1 versus 33 males and 31 females, average age 14.8 years in Group 2. Major scoliosis in Group 1 averaged 125.7° (21° to 252°). The extreme curves show vertebral transposition, with overlapping segments making it more than 180°. A logistic regression showed that there was linearity in BMI scores (R 2 = 0.97) for both arm span and height (R 2 = 0.94) in group 2 patients. For group 1 patients there was a significant difference in the BMI values when comparing BMI/arm span versus BMI/height (p < .0001). Mean BMI values using height was overstated by 2.8 (18.6%). The threshold at which BMI score must be calculated using arm span as opposed to the height (Delta AH) was determined to be 3 cm. Spine deformity patients experience height loss, which can impact their true BMI values thereby giving an erroneous impression of their nutritional status. The arm span should be used in patients with Delta AH >3 cm to properly assess nutritional status. Copyright © 2017 Scoliosis Research Society. Published by Elsevier Inc. All rights reserved.

Comprehensive assessment of the efficiency of high-rise construction projects in the form of urban blocks

NASA Astrophysics Data System (ADS)

Orlov, Alexandr; Chubarkina, Irina

2018-03-01

The paper is dedicated to main modern trends in the area of high-rise construction. The classification of buildings and structures by height is given. Functional distribution by the height of buildings is presented. A review of positive and negative aspects of high-rise construction from the economic point of view is given. On the basis of the data obtained, it is proposed to build up residential microdistricts in the form of urban blocks. A plan of microdistricts development is presented. It takes into account urban blocks and includes their main characteristics. An economic and mathematical model was developed to carry out a comprehensive assessment of the effectiveness of high-rise construction projects.

Monitoring the Deformation of High-Rise Buildings in Shanghai Luijiazui Zone by Tomo-Psinsar

NASA Astrophysics Data System (ADS)

Zhou, L. F.; Ma, P. F.; Xia, Y.; Xie, C. H.

2018-05-01

In this study, we utilize a Tomography-based Persistent Scatterers Interferometry (Tomo-PSInSAR) approach for monitoring the deformation performances of high-rise buildings, i.e. SWFC and Jin Mao Tower, in Shanghai Lujiazui Zone. For the purpose of this study, we use 31 Stripmap acquisitions from TerraSAR-X missions, spanning from December 2009 to February 2013. Considering thermal expansion, creep and shrinkage are two long-term movements that occur in high-rise buildings with concrete structures, we use an extended 4-D SAR phase model, and three parameters (height, deformation velocity, and thermal amplitude) are estimated simultaneously. Moreover, we apply a two-tier network strategy to detect single and double PSs with no need for preliminary removal of the atmospheric phase screen (APS) in the study area, avoiding possible error caused by the uncertainty in spatiotemporal filtering. Thermal expansion is illustrated in the thermal amplitude map, and deformation due to creep and shrinkage is revealed in the linear deformation velocity map. The thermal amplitude map demonstrates that the derived thermal amplitude of the two high-rise buildings both dilate and contract periodically, which is highly related to the building height due to the upward accumulative effect of thermal expansion. The linear deformation velocity map reveals that SWFC is subject to deformation during the new built period due to creep and shrinkage, which is height-dependent movements in the linear velocity map. It is worth mention that creep and shrinkage induces movements that increase with the increasing height in the downward direction. In addition, the deformation rates caused by creep and shrinkage are largest at the beginning and gradually decrease, and at last achieve a steady state as time goes infinity. On the contrary, the linear deformation velocity map shows that Jin Mao Tower is almost stable, and the reason is that it is an old built building, which is not influenced by creep and shrinkage as the load is relaxed and dehydration proceeds. This study underlines the potential of the Tomo-PSInSAR solution for the monitoring deformation performance of high-rise buildings, which offers a quantitative indicator to local authorities and planners for assessing potential damages.

Village of Arlington Heights et al. v. Metropolitan Housing Development Corp. et al. Certiorari to the United States Court of Appeals for the Seventh Circuit. Syllabus.

ERIC Educational Resources Information Center

Supreme Court of the U. S., Washington, DC.

This document presents the Supreme Court decision in the law suit between the Village of Arlington Heights, Illinois, and the Metropolitan Housing Development Corporation (MHDC). MHDC, a nonprofit developer contracted to purchase a tract within the boundaries of the Village of Arlington Heights, Illinois in order to build racially integrated low…

Building capacity for providing canopy cover and canopy height at FIA plot locations using high-resolution imagery and leaf-off LiDAR

Treesearch

Rachel Riemann; Jarlath O' Neil-Dunne; Greg C. Liknes

2012-01-01

Tree canopy cover and canopy height information are essential for estimating volume, biomass, and carbon; defining forest cover; and characterizing wildlife habitat. The amount of tree canopy cover also influences water quality and quantity in both rural and urban settings. Tree canopy cover and canopy height are currently collected at FIA plots either in the field or...

MyPlate: Build a Healthy Eating Style

MedlinePlus

... Kids Students Teens College Adults Men and Women Moms/ Moms-to-Be Older Adults Families MyPlate, MyWins for ... of calories for you based on your age, sex, height, weight, and physical activity level. Building a ...

6. INTERIOR DETAIL OF WINDOW IN EAST WALL NORTH END ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. INTERIOR DETAIL OF WINDOW IN EAST WALL NORTH END ROOM. BUILDING 4 IS VISIBLE THROUGH WINDOW. - Chollas Heights Naval Radio Transmitting Facility, Recreation Building, 6410 Zero Road, San Diego, San Diego County, CA

Identifying Populace Susceptible to Flooding Using ArcGIS and Remote Sensing Datasets

NASA Astrophysics Data System (ADS)

Fernandez, Sim Joseph; Milano, Alan

2016-07-01

Remote sensing technologies are growing vastly as with its various applications. The Department of Science and Technology (DOST), Republic of the Philippines, has made projects exploiting LiDAR datasets from remote sensing technologies. The Phil-LiDAR 1 project of DOST is a flood hazard mapping project. Among the project's objectives is the identification of building features which can be associated to the flood-exposed population. The extraction of building features from the LiDAR dataset is arduous as it requires manual identification of building features on an elevation map. The mapping of building footprints is made meticulous in order to compensate the accuracy between building floor area and building height both of which are crucial in flood decision making. A building identification method was developed to generate a LiDAR derivative which will serve as a guide in mapping building footprints. The method utilizes several tools of a Geographic Information System (GIS) software called ArcGIS which can operate on physical attributes of buildings such as roofing curvature, slope and blueprint area in order to obtain the LiDAR derivative from LiDAR dataset. The method also uses an intermediary process called building removal process wherein buildings and other features lying below the defined minimum building height - 2 meters in the case of Phil-LiDAR 1 project - are removed. The building identification method was developed in the hope to hasten the identification of building features especially when orthophotographs and/or satellite imageries are not made available.

BDW-1

EPA Pesticide Factsheets

This data set is associated with the results found in the journal article: Perry et al, 2016. Characterization of pollutant dispersion near elongated buildings based on wind tunnel simulations, Atmospheric Environment, 142, 286-295.The paper presents a wind tunnel study of the effects of elongated rectangular buildings on the dispersion of pollutants from nearby stacks. The study examines the influence of source location, building aspect ratio, and wind direction on pollutant dispersion with the goal of developing improved algorithms within dispersion models. The paper also examines the current AERMOD/PRIME modeling capabilities compared to wind tunnel observations. Differences in the amount of plume material entrained in the wake region downwind of a building for various source locations and source heights are illustrated with vertical and lateral concentration profiles. These profiles were parameterized using the Gaussian equation and show the influence of building/source configurations on those parameters. When the building is oriented at 4500b0 to the approach flow, for example, the effective plume height descends more rapidly than it does for a perpendicular building, enhancing the resulting surface concentrations in the wake region. Buildings at angles to the wind cause a cross-wind shift in the location of the plume resulting from a lateral mean flow established in the building wake. These and other effects that are not well represented in many dispersio

Characterization of pollutant dispersion near elongated ...

EPA Pesticide Factsheets

This paper presents a wind tunnel study of the effects of elongated rectangular buildings on the dispersion of pollutants from nearby stacks. The study examines the influence of source location, building aspect ratio, and wind direction on pollutant dispersion with the goal of developing improved algorithms within dispersion models. The paper also examines the current AERMOD/PRIME modeling capabilities compared to wind tunnel observations. Differences in the amount of plume material entrained in the wake region downwind of a building for various source locations and source heights are illustrated with vertical and lateral concentration profiles. These profiles were parameterized using the Gaussian equation and show the influence of building/source configurations on those parameters. When the building is oriented at 45° to the approach flow, for example, the effective plume height descends more rapidly than it does for a perpendicular building, enhancing the resulting surface concentrations in the wake region. Buildings at angles to the wind cause a cross-wind shift in the location of the plume resulting from a lateral mean flow established in the building wake. These and other effects that are not well represented in many dispersion models are important considerations when developing improved algorithms to estimate the location and magnitude of concentrations downwind of elongated buildings. The National Exposure Research Laboratory (NERL) Computational Exposur

Modeling aboveground biomass of Tamarix ramosissima in the Arkansas River Basin of Southeastern Colorado, USA

USGS Publications Warehouse

Evangelista, P.; Kumar, S.; Stohlgren, T.J.; Crall, A.W.; Newman, G.J.

2007-01-01

Predictive models of aboveground biomass of nonnative Tamarix ramosissima of various sizes were developed using destructive sampling techniques on 50 individuals and four 100-m2 plots. Each sample was measured for average height (m) of stems and canopy area (m2) prior to cutting, drying, and weighing. Five competing regression models (P < 0.05) were developed to estimate aboveground biomass of T. ramosissima using average height and/or canopy area measurements and were evaluated using Akaike's Information Criterion corrected for small sample size (AICc). Our best model (AICc = -148.69, ??AICc = 0) successfully predicted T. ramosissima aboveground biomass (R2 = 0.97) and used average height and canopy area as predictors. Our 2nd-best model, using the same predictors, was also successful in predicting aboveground biomass (R2 = 0.97, AICc = -131.71, ??AICc = 16.98). A 3rd model demonstrated high correlation between only aboveground biomass and canopy area (R2 = 0.95), while 2 additional models found high correlations between aboveground biomass and average height measurements only (R2 = 0.90 and 0.70, respectively). These models illustrate how simple field measurements, such as height and canopy area, can be used in allometric relationships to accurately predict aboveground biomass of T. ramosissima. Although a correction factor may be necessary for predictions at larger scales, the models presented will prove useful for many research and management initiatives.

5. VIEW EAST, height finder radar towers, radar tower (unknown ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. VIEW EAST, height finder radar towers, radar tower (unknown function), prime search radar tower, operations building, and central heating plant - Fort Custer Military Reservation, P-67 Radar Station, .25 mile north of Dickman Road, east of Clark Road, Battle Creek, Calhoun County, MI

Effect of Response Reduction Factor on Peak Floor Acceleration Demand in Mid-Rise RC Buildings

NASA Astrophysics Data System (ADS)

Surana, Mitesh; Singh, Yogendra; Lang, Dominik H.

2017-06-01

Estimation of Peak Floor Acceleration (PFA) demand along the height of a building is crucial for the seismic safety of nonstructural components. The effect of the level of inelasticity, controlled by the response reduction factor (strength ratio), is studied using incremental dynamic analysis. A total of 1120 nonlinear dynamic analyses, using a suite of 30 recorded ground motion time histories, are performed on mid-rise reinforced-concrete (RC) moment-resisting frame buildings covering a wide range in terms of their periods of vibration. The obtained PFA demands are compared with some of the major national seismic design and retrofit codes (IS 1893 draft version, ASCE 41, EN 1998, and NZS 1170.4). It is observed that the PFA demand at the building's roof level decreases with increasing period of vibration as well as with strength ratio. However, current seismic building codes do not account for these effects thereby producing very conservative estimates of PFA demands. Based on the identified parameters affecting the PFA demand, a model to obtain the PFA distribution along the height of a building is proposed. The proposed model is validated with spectrum-compatible time history analyses of the considered buildings with different strength ratios.

Oblique Aerial Photography Tool for Building Inspection and Damage Assessment

NASA Astrophysics Data System (ADS)

Murtiyoso, A.; Remondino, F.; Rupnik, E.; Nex, F.; Grussenmeyer, P.

2014-11-01

Aerial photography has a long history of being employed for mapping purposes due to some of its main advantages, including large area imaging from above and minimization of field work. Since few years multi-camera aerial systems are becoming a practical sensor technology across a growing geospatial market, as complementary to the traditional vertical views. Multi-camera aerial systems capture not only the conventional nadir views, but also tilted images at the same time. In this paper, a particular use of such imagery in the field of building inspection as well as disaster assessment is addressed. The main idea is to inspect a building from four cardinal directions by using monoplotting functionalities. The developed application allows to measure building height and distances and to digitize man-made structures, creating 3D surfaces and building models. The realized GUI is capable of identifying a building from several oblique points of views, as well as calculates the approximate height of buildings, ground distances and basic vectorization. The geometric accuracy of the results remains a function of several parameters, namely image resolution, quality of available parameters (DEM, calibration and orientation values), user expertise and measuring capability.

Landscape metrics for three-dimension urban pattern recognition

NASA Astrophysics Data System (ADS)

Liu, M.; Hu, Y.; Zhang, W.; Li, C.

2017-12-01

Understanding how landscape pattern determines population or ecosystem dynamics is crucial for managing our landscapes. Urban areas are becoming increasingly dominant social-ecological systems, so it is important to understand patterns of urbanization. Most studies of urban landscape pattern examine land-use maps in two dimensions because the acquisition of 3-dimensional information is difficult. We used Brista software based on Quickbird images and aerial photos to interpret the height of buildings, thus incorporating a 3-dimensional approach. We estimated the feasibility and accuracy of this approach. A total of 164,345 buildings in the Liaoning central urban agglomeration of China, which included seven cities, were measured. Twelve landscape metrics were proposed or chosen to describe the urban landscape patterns in 2- and 3-dimensional scales. The ecological and social meaning of landscape metrics were analyzed with multiple correlation analysis. The results showed that classification accuracy compared with field surveys was 87.6%, which means this method for interpreting building height was acceptable. The metrics effectively reflected the urban architecture in relation to number of buildings, area, height, 3-D shape and diversity aspects. We were able to describe the urban characteristics of each city with these metrics. The metrics also captured ecological and social meanings. The proposed landscape metrics provided a new method for urban landscape analysis in three dimensions.

A two-concentric-loop iterative method in estimation of displacement height and roughness length for momentum and sensible heat.

PubMed

Zhao, Wenguang; Qualls, Russell J; Berliner, Pedro R

2008-11-01

A two-concentric-loop iterative (TCLI) method is proposed to estimate the displacement height and roughness length for momentum and sensible heat by using the measurements of wind speed and air temperature at two heights, sensible heat flux above the crop canopy, and the surface temperature of the canopy. This method is deduced theoretically from existing formulae and equations. The main advantage of this method is that data measured not only under near neutral conditions, but also under unstable and slightly stable conditions can be used to calculate the scaling parameters. Based on the data measured above an Acacia Saligna agroforestry system, the displacement height (d0) calculated by the TCLI method and by a conventional method are compared. Under strict neutral conditions, the two methods give almost the same results. Under unstable conditions, d0 values calculated by the conventional method are systematically lower than those calculated by the TCLI method, with the latter exhibiting only slightly lower values than those seen under strictly neutral conditions. Computation of the average values of the scaling parameters for the agroforestry system showed that the displacement height and roughness length for momentum are 68% and 9.4% of the average height of the tree canopy, respectively, which are similar to percentages found in the literature. The calculated roughness length for sensible heat is 6.4% of the average height of the tree canopy, a little higher than the percentages documented in the literature. When wind direction was aligned within 5 degrees of the row direction of the trees, the average displacement height calculated was about 0.6 m lower than when the wind blew across the row direction. This difference was statistically significant at the 0.0005 probability level. This implies that when the wind blows parallel to the row direction, the logarithmic profile of wind speed is shifted lower to the ground, so that, at a given height, the wind speeds are faster than when the wind blows perpendicular to the row direction.

1. OBLIQUE VIEW, NORTH AND EAST SIDES. VIEW SHOWS POSITION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. OBLIQUE VIEW, NORTH AND EAST SIDES. VIEW SHOWS POSITION OF BUILDING UNDER LEG OF TOWER 33. - Chollas Heights Naval Radio Transmitting Facility, PERS Support Storage Building, 6410 Zero Road, San Diego, San Diego County, CA

Pubertal Stress and Nutrition and their Association with Sexual Orientation and Height in the Add Health Data

PubMed Central

Bogaert, Anthony F.

2018-01-01

A number of studies have indicated that gay men tend to be shorter, on average, than heterosexual men. Less evidence exists that lesbian women are taller, on average, than heterosexual women. The most popular explanation of the association between sexual orientation and height involves prenatal factors, such that, for example, gay men may have been exposed to lower than typical androgens during fetal development, which impacts their height and sexual orientation as adults. An alternative explanation involves stress, given that stress has been associated with sexual minority identification and with lower height. Another alternative explanation involves nutrition, although its relationship is less clear with sexual minority identification. Using the Add Health data, which is a large, nationally representative and longitudinal sample of American adolescents (n = 14,786), we tested a mediation model, such that sexual orientation → pubertal stress/nutrition → height. Within men, we found that gay men (n = 126) were shorter, on average, than heterosexual men (n = 6412). None of the 24 pubertal stress-related and 15 pubertal nutrition-related variables assessed in the Add Health data mediated the relationship between sexual orientation and height in men. Within women, lesbians (n = 75) did not differ significantly in stature compared to heterosexual women (n = 6267). Thus, prenatal mechanisms (e.g., hormones, maternal immune response) are likely better candidates for explaining the height difference between gay men and heterosexual men. PMID:27511207

Pubertal Stress and Nutrition and their Association with Sexual Orientation and Height in the Add Health Data.

PubMed

Skorska, Malvina N; Bogaert, Anthony F

2017-01-01

A number of studies have indicated that gay men tend to be shorter, on average, than heterosexual men. Less evidence exists that lesbian women are taller, on average, than heterosexual women. The most popular explanation of the association between sexual orientation and height involves prenatal factors, such that, for example, gay men may have been exposed to lower than typical androgens during fetal development, which impacts their height and sexual orientation as adults. An alternative explanation involves stress, given that stress has been associated with sexual minority identification and with lower height. Another alternative explanation involves nutrition, although its relationship is less clear with sexual minority identification. Using the Add Health data, which is a large, nationally representative and longitudinal sample of American adolescents (n = 14,786), we tested a mediation model, such that sexual orientation → pubertal stress/nutrition → height. Within men, we found that gay men (n = 126) were shorter, on average, than heterosexual men (n = 6412). None of the 24 pubertal stress-related and 15 pubertal nutrition-related variables assessed in the Add Health data mediated the relationship between sexual orientation and height in men. Within women, lesbians (n = 75) did not differ significantly in stature compared to heterosexual women (n = 6267). Thus, prenatal mechanisms (e.g., hormones, maternal immune response) are likely better candidates for explaining the height difference between gay men and heterosexual men.

Turbulent Flow at 190 m Height Above London During 2006-2008: A Climatology and the Applicability of Similarity Theory

NASA Astrophysics Data System (ADS)

Wood, C. R.; Lacser, A.; Barlow, J. F.; Padhra, A.; Belcher, S. E.; Nemitz, E.; Helfter, C.; Famulari, D.; Grimmond, C. S. B.

2010-10-01

Flow and turbulence above urban terrain is more complex than above rural terrain, due to the different momentum and heat transfer characteristics that are affected by the presence of buildings (e.g. pressure variations around buildings). The applicability of similarity theory (as developed over rural terrain) is tested using observations of flow from a sonic anemometer located at 190.3 m height in London, U.K. using about 6500 h of data. Turbulence statistics—dimensionless wind speed and temperature, standard deviations and correlation coefficients for momentum and heat transfer—were analysed in three ways. First, turbulence statistics were plotted as a function only of a local stability parameter z/Λ (where Λ is the local Obukhov length and z is the height above ground); the σ i / u * values ( i = u, v, w) for neutral conditions are 2.3, 1.85 and 1.35 respectively, similar to canonical values. Second, analysis of urban mixed-layer formulations during daytime convective conditions over London was undertaken, showing that atmospheric turbulence at high altitude over large cities might not behave dissimilarly from that over rural terrain. Third, correlation coefficients for heat and momentum were analyzed with respect to local stability. The results give confidence in using the framework of local similarity for turbulence measured over London, and perhaps other cities. However, the following caveats for our data are worth noting: (i) the terrain is reasonably flat, (ii) building heights vary little over a large area, and (iii) the sensor height is above the mean roughness sublayer depth.

Investigation of Future Thermal Comforts in a Tropical Megacity Using Coupling of Energy Balance Model and Large Eddy Simulation

NASA Astrophysics Data System (ADS)

Sueishi, T.; Yucel, M.; Ashie, Y.; Varquez, A. C. G.; Inagaki, A.; Darmanto, N. S.; Nakayoshi, M.; Kanda, M.

2017-12-01

Recently, temperature in urban areas continue to rise as an effect of climate change and urbanization. Specifically, Asian megacities are projected to expand rapidly resulting to serious in the future atmospheric environment. Thus, detailed analysis of urban meteorology for Asian megacities is needed to prescribe optimum against these negative climate modifications. A building-resolving large eddy simulation (LES) coupled with an energy balance model is conducted for a highly urbanized district in central Jakarta on typical daytime hours. Five cases were considered; case 1 utilizes present urban scenario and four cases representing different urban configurations in 2050. The future configurations were based on representative concentration pathways (RCP) and shared socio-economic pathways (SSP). Building height maps and land use maps of simulation domains are shown in the attached figure (top). Case 1 3 focuses on the difference of future scenarios. Case 1 represents current climatic and urban conditions, case 2 and 3 was an idealized future represented by RCP2.6/SSP1 and RCP8.5/SSP3, respectively. More complex urban morphology was applied in case 4, vegetation and building area were changed in case 5. Meteorological inputs and anthropogenic heat emission (AHE) were calculated using Weather Research and Forecasting (WRF) model (Varquez et al [2017]). Sensible and latent heat flux from surfaces were calculated using an energy balance model (Ashie et al [2011]), with considers multi-reflection, evapotranspiration and evaporation. The results of energy balance model (shown in the middle line of figure), in addition to WRF outputs, were used as input into the PArallelized LES Model (PALM) (Raasch et al [2001]). From standard new effective temperature (SET*) which included the effects of temperature, wind speed, humidity and radiation, thermal comfort in urban area was evaluated. SET* contours at 1 m height are shown in the bottom line of the figure. Extreme climate change increase average SET* as expected; however, construction of dense high-rise buildings (case 2) can minimize this effect due to increased shading throughout the district. Acknowledgement: This research was supported by the Environment Research and Technology Development Fund (S-14) of the Ministry of the Environment, Japan.

[Estimation of spur dike-affected fish habitat area].

PubMed

Ray-Shyan, Wu; Yan-Ru, Chen; Yi-Liang, Ge

2012-04-01

Based on the HEC-RAS and River 2D modes, and taking 5% change rate of weighted usable area (WUA) as the threshold to define the spur dike- affected area of target fish species Acrossocheilus paradoxus in Fazi River in Taiwan, this paper studied the affected area of the fish habitat by spur dike, and, in combining with the references about the installations of spur dikes in Taiwan in recent 10 years, analyzed the relative importance of related affecting factors such as dike height, dike length (water block rate), average slope gradient of river way, single or double spur dike, and flow discharge. In spite of the length of the dike, the affected area in downstream was farther, and was about 2-6 times as large as that in upstream. The ratio of the affected area in downstream / upstream decreased with increasing slope gradient, but increased with increasing dike length and flow discharge. When the discharge was approximate to 10 years return periods, the ratio of the affected area would be close to a constant of 2. Building double spur dike would produce a better WUA than building single spur dike.

Spatial Variability of Geriatric Depression Risk in a High-Density City: A Data-Driven Socio-Environmental Vulnerability Mapping Approach.

PubMed

Ho, Hung Chak; Lau, Kevin Ka-Lun; Yu, Ruby; Wang, Dan; Woo, Jean; Kwok, Timothy Chi Yui; Ng, Edward

2017-08-31

Previous studies found a relationship between geriatric depression and social deprivation. However, most studies did not include environmental factors in the statistical models, introducing a bias to estimate geriatric depression risk because the urban environment was found to have significant associations with mental health. We developed a cross-sectional study with a binomial logistic regression to examine the geriatric depression risk of a high-density city based on five social vulnerability factors and four environmental measures. We constructed a socio-environmental vulnerability index by including the significant variables to map the geriatric depression risk in Hong Kong, a high-density city characterized by compact urban environment and high-rise buildings. Crude and adjusted odds ratios (ORs) of the variables were significantly different, indicating that both social and environmental variables should be included as confounding factors. For the comprehensive model controlled by all confounding factors, older adults who were of lower education had the highest geriatric depression risks (OR: 1.60 (1.21, 2.12)). Higher percentage of residential area and greater variation in building height within the neighborhood also contributed to geriatric depression risk in Hong Kong, while average building height had negative association with geriatric depression risk. In addition, the socio-environmental vulnerability index showed that higher scores were associated with higher geriatric depression risk at neighborhood scale. The results of mapping and cross-section model suggested that geriatric depression risk was associated with a compact living environment with low socio-economic conditions in historical urban areas in Hong Kong. In conclusion, our study found a significant difference in geriatric depression risk between unadjusted and adjusted models, suggesting the importance of including environmental factors in estimating geriatric depression risk. We also developed a framework to map geriatric depression risk across a city, which can be used for identifying neighborhoods with higher risk for public health surveillance and sustainable urban planning.

Spatial Variability of Geriatric Depression Risk in a High-Density City: A Data-Driven Socio-Environmental Vulnerability Mapping Approach

PubMed Central

Lau, Kevin Ka-Lun; Yu, Ruby; Wang, Dan; Kwok, Timothy Chi Yui; Ng, Edward

2017-01-01

Previous studies found a relationship between geriatric depression and social deprivation. However, most studies did not include environmental factors in the statistical models, introducing a bias to estimate geriatric depression risk because the urban environment was found to have significant associations with mental health. We developed a cross-sectional study with a binomial logistic regression to examine the geriatric depression risk of a high-density city based on five social vulnerability factors and four environmental measures. We constructed a socio-environmental vulnerability index by including the significant variables to map the geriatric depression risk in Hong Kong, a high-density city characterized by compact urban environment and high-rise buildings. Crude and adjusted odds ratios (ORs) of the variables were significantly different, indicating that both social and environmental variables should be included as confounding factors. For the comprehensive model controlled by all confounding factors, older adults who were of lower education had the highest geriatric depression risks (OR: 1.60 (1.21, 2.12)). Higher percentage of residential area and greater variation in building height within the neighborhood also contributed to geriatric depression risk in Hong Kong, while average building height had negative association with geriatric depression risk. In addition, the socio-environmental vulnerability index showed that higher scores were associated with higher geriatric depression risk at neighborhood scale. The results of mapping and cross-section model suggested that geriatric depression risk was associated with a compact living environment with low socio-economic conditions in historical urban areas in Hong Kong. In conclusion, our study found a significant difference in geriatric depression risk between unadjusted and adjusted models, suggesting the importance of including environmental factors in estimating geriatric depression risk. We also developed a framework to map geriatric depression risk across a city, which can be used for identifying neighborhoods with higher risk for public health surveillance and sustainable urban planning. PMID:28858265

47 CFR 73.812 - Rounding of power and antenna heights.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Rounding of power and antenna heights. 73.812... RADIO BROADCAST SERVICES Low Power FM Broadcast Stations (LPFM) § 73.812 Rounding of power and antenna...) Antenna radiation center, antenna height above average terrain (HAAT), and antenna supporting structure...

47 CFR 73.812 - Rounding of power and antenna heights.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Rounding of power and antenna heights. 73.812... RADIO BROADCAST SERVICES Low Power FM Broadcast Stations (LPFM) § 73.812 Rounding of power and antenna...) Antenna radiation center, antenna height above average terrain (HAAT), and antenna supporting structure...

47 CFR 73.812 - Rounding of power and antenna heights.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Rounding of power and antenna heights. 73.812... RADIO BROADCAST SERVICES Low Power FM Broadcast Stations (LPFM) § 73.812 Rounding of power and antenna...) Antenna radiation center, antenna height above average terrain (HAAT), and antenna supporting structure...

47 CFR 73.812 - Rounding of power and antenna heights.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Rounding of power and antenna heights. 73.812... RADIO BROADCAST SERVICES Low Power FM Broadcast Stations (LPFM) § 73.812 Rounding of power and antenna...) Antenna radiation center, antenna height above average terrain (HAAT), and antenna supporting structure...

47 CFR 73.812 - Rounding of power and antenna heights.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Rounding of power and antenna heights. 73.812... RADIO BROADCAST SERVICES Low Power FM Broadcast Stations (LPFM) § 73.812 Rounding of power and antenna...) Antenna radiation center, antenna height above average terrain (HAAT), and antenna supporting structure...

Reducing stem bending increases the height growth of tall pines.

PubMed

Meng, Shawn X; Lieffers, Victor J; Reid, Douglas E B; Rudnicki, Mark; Silins, Uldis; Jin, Ming

2006-01-01

The hypothesis was tested that upper limits to height growth in trees are the result of the increasing bending moment of trees as they grow in height. The increasing bending moment of tall trees demands increased radial growth at the expense of height growth to maintain mechanical stability. In this study, the bending moment of large lodgepole pine (Pinus contorta Dougl. Ex Loud. var. latifolia Engelm.) was reduced by tethering trees at 10 m height to counter the wind load. Average bending moment of tethered trees was reduced to 38% of control trees. Six years of tethering resulted in a 40% increase in height growth relative to the period before tethering. By contrast, control trees showed decreased height growth in the period after tethering treatment. Average radial growth along the bole, relative to height growth, was reduced in tethered trees. This strongly suggests that mechanical constraints play a crucial role in limiting the height growth of tall trees. Analysis of bending moment and basal area increment at both 10 m and 1.3 m showed that the amount of wood added to the stem was closely related to the bending moment produced at these heights, in both control and tethered trees. The tethering treatment also resulted in an increase in the proportion of latewood at the tethering height, relative to 1.3 m height. For untethered control trees, the ratio of bending stresses at 10 m versus 1.3 m height was close to 1 in both 1998 and 2003, suggesting a uniform stress distribution along the outer surface of the bole.

47 CFR 101.1333 - Interference protection criteria.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Maximum EIRP Watts dBW Maximum ERP 1 Watts dBW Master 941.0-941.5 1000 30 600 27.8 Fixed Remote and Master 932.0-932.5 50 17 30 14.8 1 Where ERP = EIRP/1.64.> (ii) Maximum antenna height above average terrain... Reduction Table Antenna height above average terrain (meters) EIRP Watts dBW ERP Watts dBW Above 305 200 23...

Growth response to fertilizer in a young aspen-birch stand

Treesearch

Miroslaw M. Czapowskyj; Lawrence O. Safford

1978-01-01

A thinned aspen-birch-red maple stand was fertilized with N, P, and N plus P, both with and without lime (L). Overall, treatments with N increased height growth by an average of 79 percent, and volume growth by 69 percent, over treatments without N. Lime tended to increase both average height and volume growth over each corresponding treatment without lime. The amount...

Roystonea borinquena O.F.

Treesearch

K.F Connor

2002-01-01

Roystonea borinquena is a rapidly growing tree with an average height of 12-18 m but it can reach up to 26.4 m. Young trees can average 1 m height growth annually. Diameters range from 25 to 70 cm; maximum age is 80-110 yrs. The tree has a smooth, gray trunk with a swollen base and gracefully drooping fronds. It is native to Puerto Rico, the...

Scintillometer measurements above the urban area of London

NASA Astrophysics Data System (ADS)

Pauscher, Lukas; Salmond, Jennifer; Grimmond, C. S. B.; Foken, Thomas

2010-05-01

The spatial heterogeneity of urban surfaces presents a particular challenge to the measurement of turbulent fluxes. This is particularly true close to the urban surface (in the roughness sub-layer (RSL)) where the mosaic of roof top and street canyon surfaces present a complex three dimensional source area. Scintillometery, which offers the ability to make path-averaged measurements of turbulent fluxes of heat and momentum, provides an alternative approach to obtaining more spatially representative data sets in the RSL. In this study three Scintec small aperture scintillometers (SLS 20) were used to measure the sensible heat flux (QH) at a densely built up site at Strand Campus, King's College London, UK. Two different surfaces (courtyard and rooftop) characteristic of the urban environment were investigated simultaneously. One of the SLS was aligned just atop a courtyard (z/zH= 0.9), while the other two were set up in two different heights (z/zH= 1 and z/zH= 1.25) above a rooftop line. Where zH is the mean building height and z is the measurement height above ground level. Special consideration was given to the estimation of the displacement height and the influence of the Monin-Obukov function used for the analysis. To estimate the contribution of the different surface types to the observed fluxes a footprint analysis was carried out for the two rooftop SLS and the eddy covariance system. Fluxes from the two SLS above the rooftop generally agreed well with each other and exhibited a pronounced diurnal cycle. They also showed similar patterns and magnitudes as those measured by an eddy covariance system located close by. In contrast, diurnal flux patterns derived from the measurements atop the courtyard showed marked differences, especially during day time when fluxes often remained smaller.

Height extrapolation of wind data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mikhail, A.S.

1982-11-01

Hourly average data for a period of 1 year from three tall meteorological towers - the Erie tower in Colorado, the Goodnoe Hills tower in Washington and the WKY-TV tower in Oklahoma - were used to analyze the wind shear exponent variabiilty with various parameters such as thermal stability, anemometer level wind speed, projection height and surface roughness. Different proposed models for prediction of height variability of short-term average wind speeds were discussed. Other models that predict the height dependence of Weilbull distribution parameters were tested. The observed power law exponent for all three towers showed strong dependence on themore » anemometer level wind speed and stability (nighttime and daytime). It also exhibited a high degree of dependence on extrapolation height with respect to anemometer height. These dependences became less severe as the anemometer level wind speeds were increased due to the turbulent mixing of the atmospheric boundary layer. The three models used for Weibull distribution parameter extrapolation were he velocity-dependent power law model (Justus), the velocity, surface roughness, and height-dependent model (Mikhail) and the velocity and surface roughness-dependent model (NASA). The models projected the scale parameter C fairly accurately for the Goodnoe Hills and WKY-TV towers and were less accurate for the Erie tower. However, all models overestimated the C value. The maximum error for the Mikhail model was less than 2% for Goodnoe Hills, 6% for WKY-TV and 28% for Erie. The error associated with the prediction of the shape factor (K) was similar for the NASA, Mikhail and Justus models. It ranged from 20 to 25%. The effect of the misestimation of hub-height distribution parameters (C and K) on average power output is briefly discussed.« less

Individualized adjustments to reference phantom internal organ dosimetry—scaling factors given knowledge of patient external anatomy

NASA Astrophysics Data System (ADS)

Wayson, Michael B.; Bolch, Wesley E.

2018-04-01

Internal radiation dose estimates for diagnostic nuclear medicine procedures are typically calculated for a reference individual. Resultantly, there is uncertainty when determining the organ doses to patients who are not at 50th percentile on either height or weight. This study aims to better personalize internal radiation dose estimates for individual patients by modifying the dose estimates calculated for reference individuals based on easily obtainable morphometric characteristics of the patient. Phantoms of different sitting heights and waist circumferences were constructed based on computational reference phantoms for the newborn, 10 year-old, and adult. Monoenergetic photons and electrons were then simulated separately at 15 energies. Photon and electron specific absorbed fractions (SAFs) were computed for the newly constructed non-reference phantoms and compared to SAFs previously generated for the age-matched reference phantoms. Differences in SAFs were correlated to changes in sitting height and waist circumference to develop scaling factors that could be applied to reference SAFs as morphometry corrections. A further set of arbitrary non-reference phantoms were then constructed and used in validation studies for the SAF scaling factors. Both photon and electron dose scaling methods were found to increase average accuracy when sitting height was used as the scaling parameter (~11%). Photon waist circumference-based scaling factors showed modest increases in average accuracy (~7%) for underweight individuals, but not for overweight individuals. Electron waist circumference-based scaling factors did not show increases in average accuracy. When sitting height and waist circumference scaling factors were combined, modest average gains in accuracy were observed for photons (~6%), but not for electrons. Both photon and electron absorbed doses are more reliably scaled using scaling factors computed in this study. They can be effectively scaled using sitting height alone as patient-specific morphometric parameter.

Individualized adjustments to reference phantom internal organ dosimetry-scaling factors given knowledge of patient external anatomy.

PubMed

Wayson, Michael B; Bolch, Wesley E

2018-04-13

Internal radiation dose estimates for diagnostic nuclear medicine procedures are typically calculated for a reference individual. Resultantly, there is uncertainty when determining the organ doses to patients who are not at 50th percentile on either height or weight. This study aims to better personalize internal radiation dose estimates for individual patients by modifying the dose estimates calculated for reference individuals based on easily obtainable morphometric characteristics of the patient. Phantoms of different sitting heights and waist circumferences were constructed based on computational reference phantoms for the newborn, 10 year-old, and adult. Monoenergetic photons and electrons were then simulated separately at 15 energies. Photon and electron specific absorbed fractions (SAFs) were computed for the newly constructed non-reference phantoms and compared to SAFs previously generated for the age-matched reference phantoms. Differences in SAFs were correlated to changes in sitting height and waist circumference to develop scaling factors that could be applied to reference SAFs as morphometry corrections. A further set of arbitrary non-reference phantoms were then constructed and used in validation studies for the SAF scaling factors. Both photon and electron dose scaling methods were found to increase average accuracy when sitting height was used as the scaling parameter (~11%). Photon waist circumference-based scaling factors showed modest increases in average accuracy (~7%) for underweight individuals, but not for overweight individuals. Electron waist circumference-based scaling factors did not show increases in average accuracy. When sitting height and waist circumference scaling factors were combined, modest average gains in accuracy were observed for photons (~6%), but not for electrons. Both photon and electron absorbed doses are more reliably scaled using scaling factors computed in this study. They can be effectively scaled using sitting height alone as patient-specific morphometric parameter.

Temporal trends, regional variation and socio-economic differences in height, BMI and body proportions among German conscripts, 1956-2010.

PubMed

Lehmann, Andreas; Floris, Joël; Woitek, Ulrich; Rühli, Frank J; Staub, Kaspar

2017-02-01

We analyse temporal trends and regional variation among the most recent available anthropometric data from German conscription in the years 2008-2010 and their historical contextualization since 1956. Design/setting/subjects The overall sample included German conscripts (N 13 857 313) from 1956 to 2010. German conscripts changed from growing in height to growing in breadth. Over the analysed 54 years, average height of 19-year-old conscripts increased by 6·5 cm from 173·5 cm in 1956 (birth year 1937) to 180·0 cm in 2010 (birth year 1991). This increase plateaued since the 1990s (1970s birth years). The increase in average weight, however, did not lessen during the last two decades but increased in two steps: at the end of the 1980s and after 1999. The weight and BMI distributions became increasingly right-skewed, the prevalence of overweight and obesity increased from 11·6 % and 2·1 % in 1984 to 19·9 % and 8·5 % in 2010, respectively. The north-south gradient in height (north = taller) persisted during our observations. Height and weight of conscripts from East Germany matched the German average between the early 1990s and 2009. Between the 1980s and the early 1990s, the average chest circumference increased, the average difference between chest circumference when inhaling and exhaling decreased, as did leg length relative to trunk length. Measuring anthropometric data for military conscripts yielded year-by-year monitoring of the health status of young men at a proscribed age. Such findings contribute to a more precise identification of groups at risk and thus help with further studies and to target interventions.

The countermovement jump to monitor neuromuscular status: A meta-analysis.

PubMed

Claudino, João Gustavo; Cronin, John; Mezêncio, Bruno; McMaster, Daniel Travis; McGuigan, Michael; Tricoli, Valmor; Amadio, Alberto Carlos; Serrão, Julio Cerca

2017-04-01

The primary objective of this meta-analysis was to compare countermovement jump (CMJ) performance in studies that reported the highest value as opposed to average value for the purposes of monitoring neuromuscular status (i.e., fatigue and supercompensation). The secondary aim was to determine the sensitivity of the dependent variables. Systematic review with meta-analysis. The meta-analysis was conducted on the highest or average of a number of CMJ variables. Multiple literature searches were undertaken in Pubmed, Scopus, and Web of Science to identify articles utilizing CMJ to monitor training status. Effect sizes (ES) with 95% confidence interval (95% CI) were calculated using the mean and standard deviation of the pre- and post-testing data. The coefficient of variation (CV) with 95% CI was also calculated to assess the level of instability of each variable. Heterogeneity was assessed using a random-effects model. 151 articles were included providing a total of 531 ESs for the meta-analyses; 85.4% of articles used highest CMJ height, 13.2% used average and 1.3% used both when reporting changes in CMJ performance. Based on the meta-analysis, average CMJ height was more sensitive than highest CMJ height in detecting CMJ fatigue and supercompensation. Furthermore, other CMJ variables such as peak power, mean power, peak velocity, peak force, mean impulse, and power were sensitive in tracking the supercompensation effects of training. The average CMJ height was more sensitive than highest CMJ height in monitoring neuromuscular status; however, further investigation is needed to determine the sensitivity of other CMJ performance variables. Copyright © 2016 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

2. A 1993 'rephotograph' of the 1917 context view (WA203A1) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. A 1993 're-photograph' of the 1917 context view (WA-203-A-1) looking east along Farragut Avenue. Building 78 is the brick building on right. Building 59 (Pattern Shop) is the brick building on left side of street, just beyond the tallest modern building. The 1917 view was taken from a hill which was later removed. The 1993 view was taken from a lift at the estimated height/position of the former hill. - Puget Sound Naval Shipyard, Administration Building, Farragut Avenue, Bremerton, Kitsap County, WA

Impact of input data uncertainty on environmental exposure assessment models: A case study for electromagnetic field modelling from mobile phone base stations.

PubMed

Beekhuizen, Johan; Heuvelink, Gerard B M; Huss, Anke; Bürgi, Alfred; Kromhout, Hans; Vermeulen, Roel

2014-11-01

With the increased availability of spatial data and computing power, spatial prediction approaches have become a standard tool for exposure assessment in environmental epidemiology. However, such models are largely dependent on accurate input data. Uncertainties in the input data can therefore have a large effect on model predictions, but are rarely quantified. With Monte Carlo simulation we assessed the effect of input uncertainty on the prediction of radio-frequency electromagnetic fields (RF-EMF) from mobile phone base stations at 252 receptor sites in Amsterdam, The Netherlands. The impact on ranking and classification was determined by computing the Spearman correlations and weighted Cohen's Kappas (based on tertiles of the RF-EMF exposure distribution) between modelled values and RF-EMF measurements performed at the receptor sites. The uncertainty in modelled RF-EMF levels was large with a median coefficient of variation of 1.5. Uncertainty in receptor site height, building damping and building height contributed most to model output uncertainty. For exposure ranking and classification, the heights of buildings and receptor sites were the most important sources of uncertainty, followed by building damping, antenna- and site location. Uncertainty in antenna power, tilt, height and direction had a smaller impact on model performance. We quantified the effect of input data uncertainty on the prediction accuracy of an RF-EMF environmental exposure model, thereby identifying the most important sources of uncertainty and estimating the total uncertainty stemming from potential errors in the input data. This approach can be used to optimize the model and better interpret model output. Copyright © 2014 Elsevier Inc. All rights reserved.

Movable-Bed Laboratory Experiments Comparing Radiation Stress and Energy Flux Factor as Predictors of Longshore Transport Rate.

DTIC Science & Technology

1981-04-01

acceleration of gravity H wave height H average wave height Hrms root-mean-square wave height Hs significant wave height IX longshore transport rate in...wave height, H, measured during the tests (and discussed later in Section IV) is equal to Hrms . By rewriting equation (4), S ( Cg cos.) C (7) xy 8 Cg...only for conditions where H equals Hrms * 2. Energy Flux. In literature, the longshore transport rate has been empirically related most frequently to a

A comprehensive study on urban true orthorectification

USGS Publications Warehouse

Zhou, G.; Chen, W.; Kelmelis, J.A.; Zhang, Dongxiao

2005-01-01

To provide some advanced technical bases (algorithms and procedures) and experience needed for national large-scale digital orthophoto generation and revision of the Standards for National Large-Scale City Digital Orthophoto in the National Digital Orthophoto Program (NDOP), this paper presents a comprehensive study on theories, algorithms, and methods of large-scale urban orthoimage generation. The procedures of orthorectification for digital terrain model (DTM)-based and digital building model (DBM)-based orthoimage generation and their mergence for true orthoimage generation are discussed in detail. A method of compensating for building occlusions using photogrammetric geometry is developed. The data structure needed to model urban buildings for accurately generating urban orthoimages is presented. Shadow detection and removal, the optimization of seamline for automatic mosaic, and the radiometric balance of neighbor images are discussed. Street visibility analysis, including the relationship between flight height, building height, street width, and relative location of the street to the imaging center, is analyzed for complete true orthoimage generation. The experimental results demonstrated that our method can effectively and correctly orthorectify the displacements caused by terrain and buildings in urban large-scale aerial images. ?? 2005 IEEE.

Fine-Scale Population Estimation by 3D Reconstruction of Urban Residential Buildings

PubMed Central

Wang, Shixin; Tian, Ye; Zhou, Yi; Liu, Wenliang; Lin, Chenxi

2016-01-01

Fine-scale population estimation is essential in emergency response and epidemiological applications as well as urban planning and management. However, representing populations in heterogeneous urban regions with a finer resolution is a challenge. This study aims to obtain fine-scale population distribution based on 3D reconstruction of urban residential buildings with morphological operations using optical high-resolution (HR) images from the Chinese No. 3 Resources Satellite (ZY-3). Specifically, the research area was first divided into three categories when dasymetric mapping was taken into consideration. The results demonstrate that the morphological building index (MBI) yielded better results than built-up presence index (PanTex) in building detection, and the morphological shadow index (MSI) outperformed color invariant indices (CIIT) in shadow extraction and height retrieval. Building extraction and height retrieval were then combined to reconstruct 3D models and to estimate population. Final results show that this approach is effective in fine-scale population estimation, with a mean relative error of 16.46% and an overall Relative Total Absolute Error (RATE) of 0.158. This study gives significant insights into fine-scale population estimation in complicated urban landscapes, when detailed 3D information of buildings is unavailable. PMID:27775670

How tall buildings affect turbulent air flows and dispersion of pollution within a neighbourhood.

PubMed

Aristodemou, Elsa; Boganegra, Luz Maria; Mottet, Laetitia; Pavlidis, Dimitrios; Constantinou, Achilleas; Pain, Christopher; Robins, Alan; ApSimon, Helen

2018-02-01

The city of London, UK, has seen in recent years an increase in the number of high-rise/multi-storey buildings ("skyscrapers") with roof heights reaching 150 m and more, with the Shard being a prime example with a height of ∼310 m. This changing cityscape together with recent plans of local authorities of introducing Combined Heat and Power Plant (CHP) led to a detailed study in which CFD and wind tunnel studies were carried out to assess the effect of such high-rise buildings on the dispersion of air pollution in their vicinity. A new, open-source simulator, FLUIDITY, which incorporates the Large Eddy Simulation (LES) method, was implemented; the simulated results were subsequently validated against experimental measurements from the EnFlo wind tunnel. The novelty of the LES methodology within FLUIDITY is based on the combination of an adaptive, unstructured, mesh with an eddy-viscosity tensor (for the sub-grid scales) that is anisotropic. The simulated normalised mean concentrations results were compared to the corresponding wind tunnel measurements, showing for most detector locations good correlations, with differences ranging from 3% to 37%. The validation procedure was followed by the simulation of two further hypothetical scenarios, in which the heights of buildings surrounding the source building were increased. The results showed clearly how the high-rise buildings affected the surrounding air flows and dispersion patterns, with the generation of "dead-zones" and high-concentration "hotspots" in areas where these did not previously exist. The work clearly showed that complex CFD modelling can provide useful information to urban planners when changes to cityscapes are considered, so that design options can be tested against environmental quality criteria. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Global distribution of urban parameters derived from high-resolution global datasets for weather modelling

NASA Astrophysics Data System (ADS)

Kawano, N.; Varquez, A. C. G.; Dong, Y.; Kanda, M.

2016-12-01

Numerical model such as Weather Research and Forecasting model coupled with single-layer Urban Canopy Model (WRF-UCM) is one of the powerful tools to investigate urban heat island. Urban parameters such as average building height (Have), plain area index (λp) and frontal area index (λf), are necessary inputs for the model. In general, these parameters are uniformly assumed in WRF-UCM but this leads to unrealistic urban representation. Distributed urban parameters can also be incorporated into WRF-UCM to consider a detail urban effect. The problem is that distributed building information is not readily available for most megacities especially in developing countries. Furthermore, acquiring real building parameters often require huge amount of time and money. In this study, we investigated the potential of using globally available satellite-captured datasets for the estimation of the parameters, Have, λp, and λf. Global datasets comprised of high spatial resolution population dataset (LandScan by Oak Ridge National Laboratory), nighttime lights (NOAA), and vegetation fraction (NASA). True samples of Have, λp, and λf were acquired from actual building footprints from satellite images and 3D building database of Tokyo, New York, Paris, Melbourne, Istanbul, Jakarta and so on. Regression equations were then derived from the block-averaging of spatial pairs of real parameters and global datasets. Results show that two regression curves to estimate Have and λf from the combination of population and nightlight are necessary depending on the city's level of development. An index which can be used to decide which equation to use for a city is the Gross Domestic Product (GDP). On the other hand, λphas less dependence on GDP but indicated a negative relationship to vegetation fraction. Finally, a simplified but precise approximation of urban parameters through readily-available, high-resolution global datasets and our derived regressions can be utilized to estimate a global distribution of urban parameters for later incorporation into a weather model, thus allowing us to acquire a global understanding of urban climate (Global Urban Climatology). Acknowledgment: This research was supported by the Environment Research and Technology Development Fund (S-14) of the Ministry of the Environment, Japan.

Influences of source condition and dissolution on bubble plume in a stratified environment

NASA Astrophysics Data System (ADS)

Chu, Shigan; Prosperetti, Andrea

2017-11-01

A cross-sectionally averaged model is used to study a bubble plume rising in a stratified quiescent liquid. Scaling analyses for the peel height, at which the plume momentum vanishes, and the neutral height, at which its average density equals the ambient density, are presented. Contrary to a widespread practice in the literature, it is argued that the neutral height cannot be identified with the experimentally reported intrusion height. Recognizing this difference provides an explanation of the reason why the intrusion height is found so frequently to lie so much above predictions, and brings the theoretical results in line with observations. The mathematical model depends on three dimensionless parameters, some of which are related to the inlet conditions at the plume source. Their influence on the peel and neutral heights is illustrated by means of numerical results. Aside from the source parameters, we incorporate dissolution of bubbles and the corresponding density change of plume into the model. Contrary to what's documented in literature, density change of plume due to dissolution plays an important role in keeping the total buoyancy of plume, thus alleviating the rapid decrease of peel height because of dissolution.

[Use of computerized stabylometric footboard in evaluation of work suitability at height work in building firms].

PubMed

D'Orso, M I; Garaguso, M; Ferrari, G; Riva, M A; Gallamini, M; Cesana, G

2012-01-01

A relevant part of deadly work accidents and of severe work accidents reported in national specific statistics coming from INAIL is until today caused by workers' falls during their at height work activities. Medical evaluation of eventual workers' hyper susceptibility to fall caused by balance alterations, if included in medical surveillance, is frequently carried out by medical doctors using different subjective tests included in different clinical protocols. Use of a computerized stabylometric footboard on the contrary allows to obtain objective and reproducible data concerning vestibular function which, associated with traditional clinical medical evaluation, seem to better detect eventual presence of balance disturbances, especially those non clinically perceivable by workers and therefore more dangerous. We report results evidenced in a research carried out in a group of 185 workers engaged in building firms and having work tasks including phases of at height work.

Red-shouldered hawk nesting habitat preference in south Texas

USGS Publications Warehouse

Strobel, Bradley N.; Boal, Clint W.

2010-01-01

We examined nesting habitat preference by red-shouldered hawks Buteo lineatus using conditional logistic regression on characteristics measured at 27 occupied nest sites and 68 unused sites in 2005–2009 in south Texas. We measured vegetation characteristics of individual trees (nest trees and unused trees) and corresponding 0.04-ha plots. We evaluated the importance of tree and plot characteristics to nesting habitat selection by comparing a priori tree-specific and plot-specific models using Akaike's information criterion. Models with only plot variables carried 14% more weight than models with only center tree variables. The model-averaged odds ratios indicated red-shouldered hawks selected to nest in taller trees and in areas with higher average diameter at breast height than randomly available within the forest stand. Relative to randomly selected areas, each 1-m increase in nest tree height and 1-cm increase in the plot average diameter at breast height increased the probability of selection by 85% and 10%, respectively. Our results indicate that red-shouldered hawks select nesting habitat based on vegetation characteristics of individual trees as well as the 0.04-ha area surrounding the tree. Our results indicate forest management practices resulting in tall forest stands with large average diameter at breast height would benefit red-shouldered hawks in south Texas.

Building Change Detection from Harvey using Unmanned Aerial System (UAS)

NASA Astrophysics Data System (ADS)

Chang, A.; Yeom, J.; Jung, J.; Choi, I.

2017-12-01

Unmanned Aerial System (UAS) is getting to be the most important technique in recent days since the fine spatial and high temporal resolution data previously unobtainable from traditional remote sensing platforms. Advanced UAS data can provide a great opportunity for disaster monitoring. Especially, building change detection is the one of the most important topics for damage assessment and recovery from disasters. This study is proposing a method to monitor building change with UAS data for Holiday Beach in Texas, where was directly hit by Harvey on 25 August 2017. This study adopted 3D change detection to monitor building damage and recovery levels with building height as well as natural color information. We used a rotorcraft UAS to collect RGB data twice on 9 September and 18 October 2017 after the hurricane. The UAS data was processed using Agisoft Photoscan Pro Software to generate super high resolution dataset including orthomosaic, DSM (Digital Surface Model), and 3D point cloud. We compared the processed dataset with an airborne image considerable as before-hurricane data, which was acquired on January 2016. Building damage and recovery levels were determined by height and color change. The result will show that UAS data is useful to assess building damage and recovery for affected area by the natural disaster such as Harvey.

76 FR 70109 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-10

... DEPARTMENT OF COMMERCE Submission for OMB Review; Comment Request The Department of Commerce will... occupant egress from high-rise buildings. Buildings of interest include varying heights, and of varying occupancy types, e.g., residential, office, and assembly occupancies. Data will be collected via...

Extraction and height estimation of artificial vertical structures based on the wrapped interferometric phase difference within their layovers

NASA Astrophysics Data System (ADS)

Uemoto, Jyunpei; Nadai, Akitsugu; Kojima, Shoichiro; Kobayashi, Tatsuharu; Umehara, Toshihiko; Matsuoka, Takeshi; Uratsuka, Seiho; Satake, Makoto

2018-05-01

The geometric modulation of synthetic aperture radar (SAR) imagery such as radar shadow, foreshortening, and layover often complicates image interpretation while it contains useful information about targets. Recently, some methods for automatic building detection utilizing a peculiar pattern of phase differences (PDs) within building layovers on SAR interferograms have been proposed. One of the merits of these methods is the capability to detect buildings even taller than the height of ambiguity without incorporating any external data. In this paper, we propose a new method that has achieved the following improvements while maintaining the merit mentioned above. The first improvement is freedom from the dependence of target heights; without changing any parameters and thresholds, the proposed method can detect low-rise apartments to skyscrapers. The second one is the prevention of the false grouping of vertical structure constituents by considering relationships between their PDs. In addition, the method can measure the height of vertical structures without assuming their shape to be simple ones such as a parallelogram. These improvements have been verified by applying the method to real datasets acquired from an airborne X-band SAR. The quantitative assessment for apartment complexes has demonstrated the high performance of the method; the correctness and completeness are 94% and 83%, respectively. The mean error in the measured height is -0.2 m, while the standard deviation is 1.8 m. The verification using real datasets has revealed at the same time that the performance of the method can be degraded due to the crowdedness in dense urban areas including skyscrapers and owing to the poor discriminability between artificial vertical structures and trees. Overcoming these limitations is necessary in future studies.

SU-D-209-04: Raise Your Table: An Effective Way to Reduce Radiation Dose for Fluoroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huo, D; Hoerner, M; Toskich, B

2016-06-15

Purpose: Patient table height plays an important role in estimating patient skin dose for interventional radiology (IR) procedures, because the patient’s skin location is dependent on the height of table. Variation in table height can lead to as much as 150% difference in skin dose for patient exams with similar air kerma meter readings. In our facility, IR procedural workflow was recently changed to require the IR physicians to confirm the patient table height before the procedure. The patient table height data was collected before and after this workflow change to validate the implementation of this practice. Methods: Table heightmore » information was analyzed for all procedures performed in three IR rooms, which were impacted by the workflow change, covering three months before and after the change (Aug 2015 to Jan 2016). In total, 442, 425, and 390 procedures were performed in these three rooms over this time period. There were no personnel or procedure assignment changes during the six-month period of time. Statistical analysis was performed for the average table height changes before and after the workflow change. Results: For the three IR rooms investigated, after the workflow change, the average table heights were increased by 1.43 cm (p=0.004084), 0.66 cm (p=0.187089), and 1.59 cm (p=0.002193), providing a corresponding estimated skin dose savings of 6.76%, 2.94% and 7.62%, respectively. After the workflow change, the average table height was increased by 0.95 cm, 0.63 cm, 0.55 cm, 1.07 cm, 1.12 cm, and 3.36 cm for the six physicians who routinely work in these three rooms. Conclusion: Consistent improvement in table height settings has been observed for all IR rooms and all physicians following a simple workflow change. This change has led to significant patient dose savings by making physicians aware of the pre-procedure table position.« less

Variability in early height growth rate of forest trees: implications for retrospective studies of stand dynamics

Treesearch

Brain J. Palik; Kurt S. Pregitzer

1995-01-01

Retrospective studies of forest stand dynamics may rely on estimates of tree ages. In some of these studies, trees are aged near the stem base, while in other studies trees may be aged at breast height. An age correction may be added to breast-height ages in an attempt to account for average time to reach breast height and thus provide better estimates of total ages....

Height, social comparison, and paranoia: An immersive virtual reality experimental study

PubMed Central

Freeman, Daniel; Evans, Nicole; Lister, Rachel; Antley, Angus; Dunn, Graham; Slater, Mel

2014-01-01

Mistrust of others may build upon perceptions of the self as vulnerable, consistent with an association of paranoia with perceived lower social rank. Height is a marker of social status and authority. Therefore we tested the effect of manipulating height, as a proxy for social rank, on paranoia. Height was manipulated within an immersive virtual reality simulation. Sixty females who reported paranoia experienced a virtual reality train ride twice: at their normal and reduced height. Paranoia and social comparison were assessed. Reducing a person's height resulted in more negative views of the self in comparison with other people and increased levels of paranoia. The increase in paranoia was fully mediated by changes in social comparison. The study provides the first demonstration that reducing height in a social situation increases the occurrence of paranoia. The findings indicate that negative social comparison is a cause of mistrust. PMID:24924485

STEREOSCOPIC DETERMINATION OF HEIGHTS OF EXTREME ULTRAVIOLET BRIGHT POINTS USING DATA TAKEN BY SECCHI/EUVI ABOARD STEREO

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kwon, Ryun-Young; Chae, Jongchul; Zhang Jie

2010-05-01

We measure the heights of EUV bright points (BPs) above the solar surface by applying a stereoscopic method to the data taken by the Solar TErrestrial RElations Observatory/SECCHI/Extreme UltraViolet Imager (EUVI). We have developed a three-dimensional reconstruction method for point-like features such as BPs using the simple principle that the position of a point in the three-dimensional space is specified as the intersection of two lines of sight. From a set of data consisting of EUVI 171 A, 195 A, 284 A, and 304 A images taken on 11 days arbitrarily selected during a period of 14 months, we havemore » identified and analyzed 210 individual BPs that were visible on all four passband images and smaller than 30 Mm. The BPs seen in the 304 A images have an average height of 4.4 Mm, and are often associated with the legs of coronal loops. In the 171 A, 195 A, and 284 A images the BPs appear loop-shaped, and have average heights of 5.1, 6.7, and 6.1 Mm, respectively. Moreover, there is a tendency that overlying loops are filled with hotter plasmas. The average heights of BPs in 171 A, 195 A, and 284 A passbands are roughly twice the corresponding average lengths. Our results support the notion that an EUV BP represents a system of small loops with temperature stratification like flaring loops, being consistent with the magnetic reconnection origin.« less

Growth process and model simulation of three different classes of Schima superba in a natural subtropical forest in China

NASA Astrophysics Data System (ADS)

Wei, Hui; Deng, Xiangwen; Ouyang, Shuai; Chen, Lijun; Chu, Yonghe

2017-01-01

Schima superba is an important fire-resistant, high-quality timber species in southern China. Growth in height, diameter at breast height (DBH), and volume of the three different classes (overtopped, average and dominant) of S. superba were examined in a natural subtropical forest. Four growth models (Richards, edited Weibull, Logistic and Gompertz) were selected to fit the growth of the three different classes of trees. The results showed that there was a fluctuation phenomenon in height and DBH current annual growth process of all three classes. Multiple intersections were found between current annual increment (CAI) and mean annual increment (MAI) curves of both height and DBH, but there was no intersection between volume CAI and MAI curves. All selected models could be used to fit the growth of the three classes of S. superba, with determinant coefficients above 0.9637. However, the edited Weibull model performed best with the highest R2 and the lowest root of mean square error (RMSE). S. superba is a fast-growing tree with a higher growth rate during youth. The height and DBH CAIs of overtopped, average and dominant trees reached growth peaks at ages 5-10, 10-15 and 15-20 years, respectively. According to model simulation, the volume CAIs of overtopped, average and dominant trees reached growth peaks at ages 17, 55 and 76 years, respectively. The biological rotation ages of the overtopped, average and dominant trees of S. superba were 29, 85 and 128 years, respectively.

[General growth patterns and simple mathematic models of height and weight of Chinese children].

PubMed

Zong, Xin-nan; Li, Hui

2009-05-01

To explore the growth patterns and simple mathematic models of height and weight of Chinese children. The original data had been obtained from two national representative cross-sectional surveys which were 2005 National Survey of Physical Development of Children (under 7 years of age) and 2005 Chinese National Survey on Students Constitution and Health (6 - 18 years). Reference curves of height and weight of children under 7 years of age was constructed by LMS method, and data of children from 6 to 18 years of age were smoothed by cubic spline function and transformed by modified LMS procedure. Growth velocity was calculated by smoothed values of height and weight. Simple linear model was fitted for children 1 to 10 years of age, for which smoothed height and weight values were used. (1) Birth length of Chinese children was about 50 cm, average length 61 cm, 67 cm, 76 cm and 88 cm at the 3rd, 6th, 12th and 24th month. Height gain was stable from 2 to 10 years of age, average 6 - 7 cm each year. Birth length doubles by 3.5 years, and triples by 12 years. The formula estimating average height of normal children aged 2 - 10 years was, height (cm) = age (yr) x 6.5 + 76 (cm). (2) Birth weight was about 3.3 kg. Growth velocity was at peak about 1.0 - 1.1 kg/mon in the first 3 months, decreased by half and was about 0.5 - 0.6 kg/mon in the second 3 months, and was reduced by a quarter, which was about 0.25 - 0.30 kg/mon, in the last 6 months of the first year. Body mass was up to doubles, triples and quadruple of birth weight at about the 3rd, 12th and 24th month. Average annual gain was about 2 kg and 3 kg from 1 - 6 years and 7 - 10 years, respectively. The estimated formula for children 1 to 6 years of age was weight (kg) = age (yr) x 2 + 8 (kg), but for those 7 - 10 years old, weight (kg) = age (yr) x 3 + 2 (kg). Growth patterns of height and weight at the different age stages were summarized for Chinese children, and simple reference data of height and weight velocity from 0 to 18 years and approximate estimation formula from 1 - 10 years was presented for clinical practice.

Sex-specific differences of craniofacial traits in Croatia: the impact of environment in a small geographic area.

PubMed

Buretic-Tomljanovic, Alena; Giacometti, Jasminka; Ostojic, Sasa; Kapovic, Miljenko

2007-01-01

Craniometric variation in humans reflects different genetic and environmental influences. Long-term climatic adaptation is less likely to show an impact on size and shape variation in a small local area than at the global level. The aim of this work was to assess the contribution of the particular environmental factors to body height and craniofacial variability in a small geographic area of Croatia. A total of 632 subjects, aged 18-21, participated in the survey. Body height, head length, head breadth, head height, head circumference, cephalic index, morphological face height, face breadth, and facial index were analysed regarding geographic, climatic and dietary conditions in different regions of the country, and correlated with the specific climatic variables (cumulative multiyear sunshine duration, cumulative multiyear average precipitation, multiyear average air temperatures) and calcium concentrations in drinking water. Significant differences between groups classified according to geographic, climatic or dietary affiliation, and the impact of the environmental predictors on the variation in the investigated traits were assessed using multiple forward stepwise regression analyses. Higher body height measures in both sexes were significantly correlated with Mediterranean diet type. Mediterranean diet type also contributed to higher head length and head circumference measures in females. Cephalic index values correlated to geographic regions in both sexes, showing an increase from southern to eastern Croatia. In the same direction, head length significantly decreased in males and head breadth increased in females. Mediterranean climate was associated with higher and narrower faces in females. The analysis of the particular climatic variables did not reveal a significant influence on body height in either sex. Concurrently, climatic features influenced all craniofacial traits in females and only head length and facial index in males. Mediterranean climate, characterized by higher average sunshine duration, higher average precipitation and higher average air temperatures, was associated with longer, higher and narrower skulls, higher head circumference, lower cephalic index, and higher and narrower faces (lower facial index). Calcium concentrations in drinking water did not correlate significantly with any dependent variable. A significant effect of environmental factors on body height and craniofacial variability was found in Croatian young adult population. This effect was more pronounced in females, revealing sex-specific craniofacial differentiation. However, the impact of environment was low and may explain only 1.0-7.32% variation of the investigated traits.

Land use and urban morphology parameters for Vienna required for initialisation of the urban canopy model TEB derived via the concept of "local climate zones"

NASA Astrophysics Data System (ADS)

Trimmel, Heidelinde; Weihs, Philipp; Oswald, Sandro M.; Masson, Valéry; Schoetter, Robert

2017-04-01

Urban settlements are generally known for their high fractions of impermeable surfaces, large heat capacity and low humidity compared to rural areas which results in the well known phenomena of urban heat islands. The urbanized areas are growing which can amplify the intensity and frequency of situations with heat stress. The distribution of the urban heat island is not uniform though, because the urban environment is highly diverse regarding its morphology as building heights, building contiguity and configuration of open spaces and trees vary, which cause changes in the aerodynamic resistance for heat transfers and drag coefficients for momentum. Furthermore cities are characterized by highly variable physical surface properties as albedo, emissivity, heat capacity and thermal conductivity. The distribution of the urban heat island is influenced by these morphological and physical parameters as well as the distribution of unsealed soil and vegetation. These aspects influence the urban climate on micro- and mesoscale. For larger Vienna high resolution vector and raster geodatasets were processed to derive land use surface fractions and building morphology parameters on block scale following the methodology of Cordeau (2016). A dataset of building age and typology was cross checked and extended using satellite visual and thermal bands and linked to a database joining building age and typology with typical physical building parameters obtained from different studies (Berger et al. 2012 and Amtmann M and Altmann-Mavaddat N (2014)) and the OIB (Österreichisches Institut für Bautechnik). Using dominant parameters obtained using this high resolution mainly ground based data sets (building height, built area fraction, unsealed fraction, sky view factor) a local climate zone classification was produced using an algorithm. The threshold values were chosen according to Stewart and Oke (2012). This approach is compared to results obtained with the methodology of Bechtel et al. (2015) which is based on machine learning algorithms depending on satellite imagery and expert knowledge. The data on urban land use and morphology are used for initialisation of the town energy balance scheme TEB, but are also useful for other urban canopy models or studies related to urban planning or modelling of the urban system. The sensitivity of canyon air and surface temperatures, air specific humidity and horizontal wind simulated by the town energy balance scheme TEB (Masson, 2000) regarding the dominant parameters within the range determined for the present urban structure of Vienna and the expected changes (MA 18 (2011, 2014a+b), PGO (2011), Amtmann M and Altmann-Mavaddat N (2014)) was calculated for different land cover zones. While the buildings heights have a standard deviation of 3.2m which is 15% of the maximum average building height of one block the built and unsealed surface fraction vary stronger with around 30% standard deviation. The pre 1919 structure of Vienna is rather uniform and easier to describe, the later building structure is more diverse regarding morphological as well as physical building parameters. Therefore largest uncertainties are possible at the urban rims where also the highest development is expected. The analysis will be focused on these areas. Amtmann M and Altmann-Mavaddat N (2014) Eine Typology österreichischer Wohngebäude, Österreichische Energieargentur - Austrian Energy Agency, TABULA/EPISCOPE Bechtel B, Alexander P, Böhner J, et al (2015) Mapping Local Climate Zones for a Worldwide Database of the Form and Function of Cities. ISPRS Int J Geo-Inf 4:199-219. doi: 10.3390/ijgi4010199 Berger T, Formayer H, Smutny R, Neururer C, Passawa R (2012) Auswirkungen des Klimawandelsauf den thermischen Komfort in Bürogebäuden, Berichte aus Energie- und Umweltforschung Cordeau E / Les îlots morphologiques urbains (IMU) / IAU îdF / 2016 Magistratsabteilung 18 - Stadtentwicklung und Stadtplanung, Wien - MA 18 (2011) Siedlungsformen für die Stadterweiterung, MA 18 (2014a) Smart City Wien - Rahmenstrategie MA 18 (2014b) Stadtentwicklungsplan STEP 2025, www.step.wien.at Masson V (2000) A physically-based scheme for the urban energy budget in atmospheric models. Bound-Layer Meteorol 94:357-397. doi: 10.1023/A:1002463829265 PGO (Planungsgemeinschaft Ost) (2011) stadtregion +, Planungskooperation zur räumlichen Entwicklung der Stadtregion Wien Niederösterreich Burgenland. Stewart ID, Oke TR (2012) Local climate zones for urban temperature studies. Bull Am Meteorol Soc 93:1879-1900.

Extremely low birth weight and body size in early adulthood

PubMed Central

Doyle, L; Faber, B; Callanan, C; Ford, G; Davis, N

2004-01-01

Aims: To determine the body size of extremely low birth weight (ELBW, birth weight 500–999 g) subjects in early adulthood. Methods: Cohort study examining the height and weight of 42 ELBW survivors free of cerebral palsy between birth and 20 years of age. Weight and height measurements were converted to Z (SD) scores. Results: At birth the subjects had weight Z scores substantially below zero (mean birth weight Z score -0.90, 95% CI -1.25 to -0.54), and had been lighter than average at ages 2, 5, and 8 years. However, by 14, and again at 20 years of age their weight Z scores were not significantly different from zero. At ages 2, 5, 8, 14, and 20 years of age their height Z scores were significantly below zero. Their height at 20 years of age was, however, consistent with their parents' height. As a group they were relatively heavy for their height and their mean body mass index (BMI) Z score was almost significantly different from zero (mean difference 0.42, 95% CI -0.02 to 0.84). Their mean BMI (kg/m2) was 24.0 (SD 5.2); 14 had a BMI >25, and four had a BMI >30. Conclusions: Despite their early small size, by early adulthood the ELBW subjects had attained an average weight, and their height was consistent with their parents' height. They were, however, relatively heavy for their height. PMID:15033844

Multi-Level Building Reconstruction for Automatic Enhancement of High Resolution Dsms

NASA Astrophysics Data System (ADS)

Arefi, H.; Reinartz, P.

2012-07-01

In this article a multi-level approach is proposed for reconstruction-based improvement of high resolution Digital Surface Models (DSMs). The concept of Levels of Detail (LOD) defined by CityGML standard has been considered as basis for abstraction levels of building roof structures. Here, the LOD1 and LOD2 which are related to prismatic and parametric roof shapes are reconstructed. Besides proposing a new approach for automatic LOD1 and LOD2 generation from high resolution DSMs, the algorithm contains two generalization levels namely horizontal and vertical. Both generalization levels are applied to prismatic model of buildings. The horizontal generalization allows controlling the approximation level of building footprints which is similar to cartographic generalization concept of the urban maps. In vertical generalization, the prismatic model is formed using an individual building height and continuous to included all flat structures locating in different height levels. The concept of LOD1 generation is based on approximation of the building footprints into rectangular or non-rectangular polygons. For a rectangular building containing one main orientation a method based on Minimum Bounding Rectangle (MBR) in employed. In contrast, a Combined Minimum Bounding Rectangle (CMBR) approach is proposed for regularization of non-rectilinear polygons, i.e. buildings without perpendicular edge directions. Both MBRand CMBR-based approaches are iteratively employed on building segments to reduce the original building footprints to a minimum number of nodes with maximum similarity to original shapes. A model driven approach based on the analysis of the 3D points of DSMs in a 2D projection plane is proposed for LOD2 generation. Accordingly, a building block is divided into smaller parts according to the direction and number of existing ridge lines. The 3D model is derived for each building part and finally, a complete parametric model is formed by merging all the 3D models of the individual parts and adjusting the nodes after the merging step. In order to provide an enhanced DSM, a surface model is provided for each building by interpolation of the internal points of the generated models. All interpolated models are situated on a Digital Terrain Model (DTM) of corresponding area to shape the enhanced DSM. Proposed DSM enhancement approach has been tested on a dataset from Munich central area. The original DSM is created using robust stereo matching of Worldview-2 stereo images. A quantitative assessment of the new DSM by comparing the heights of the ridges and eaves shows a standard deviation of better than 50cm.

Estimation procedures for understory biomass and fuel loads in sagebrush steppe invaded by woodlands

Treesearch

Alicia L. Reiner; Robin J. Tausch; Roger F. Walker

2010-01-01

Regression equations were developed to predict biomass for 9 shrubs, 9 grasses, and 10 forbs that generally dominate sagebrush ecosystems in central Nevada. Independent variables included percent cover, average height, and plant volume. We explored 2 ellipsoid volumes: one with maximum plant height and 2 crown diameters and another with live crown height and 2 crown...

Mechanical Properties of Individual Southern Pine Fibers. Part II. Comparison of Earlywood and Latewood Fibers with Respect to Tree Height and Juvenility

Treesearch

Laurence Mott; Les Groom; Stephen Shaler

2002-01-01

This paper reports variations in mechanical properties of individual southern pine fibers and compares engineering properties of earlywood and latewood tracheids with respect to tree height and juvenility. Results indicate that latewood fibers exhibit greater strength and stiffness than earlywood fibers irrespective of tree height or juvenility. Average earlywood...

Mechanical properties of individual southern pine fibers. Part II. Comparison of earlywood and latewood fibers with respect to tree height and juvenility

Treesearch

Leslie H. Groom; Stephen Shaler; Laurence Mott

2002-01-01

This paper repons variations in mechanical properties of individual southern pine fibers and compares engineering properties of earlywood and latewood tracheids with respect to tree height and juvenility. Results indicate that latewood fibers exhibit greater strength and stiffness than earlywood fibers irrespective of tree height or juvenility. Average earlywood...

Development of a Mathematical Model to Assess the Accuracy of Difference between Geodetic Heights

ERIC Educational Resources Information Center

Gairabekov, Ibragim; Kliushin, Evgenii; Gayrabekov, Magomed-Bashir; Ibragimova, Elina; Gayrabekova, Amina

2016-01-01

The article includes the results of theoretical studies of the accuracy of geodetic height survey and marks points on the Earth's surface using satellite technology. The dependence of the average square error of geodetic heights difference survey from the distance to the base point was detected. It is being proved that by using satellite…

Use of dominant tree heights in determining site index for Douglas-fir.

Treesearch

George R. Staebler

1948-01-01

Measuring heights of Douglas-fir trees for the determination of site index is a time-consuming job, especially in dense stands. Both dominant and codominant trees must be measured since site index curves represent the average height of dominants and codominants. It has been suggested that considerable time might be saved if only dominant trees were measured, since...

The biological standard of living in pre-modern Korea: Determinants of height of militia recruits during the Chosŏn dynasty.

PubMed

Jun, Seong Ho; Lewis, James B; Schwekendiek, Daniel

2017-02-01

This paper extends the research on the biological standard of living in the Korean peninsula back to pre-modern times. Drawing on militia rosters of the Chosŏn Dynasty from the sixteenth to eighteenth centuries, we tentatively conclude that the final height of Korean men during this period was 166cm and thus slightly above that of modern North Korean men (165cm). On the other hand, the average height of modern South Korean men is 172cm, 6cm more than what we tentatively estimate for pre-modern Korean men. Regression analysis of the height of pre-modern Korean men finds that un-free Koreans ("slaves") were significantly shorter by about 0.6-0.7cm than commoners, whereas the average height of recruits suffering from smallpox did not differ significantly from that of other recruits. Moreover, regional, as opposed to birth-dummy, variables account, and to a significant degree, for most of the differences in height. Whether or not this is a result of socioeconomic differences across provinces or a result of other regionally-varying factors remains an open question. Copyright © 2016 Elsevier B.V. All rights reserved.

Vibroacoustic Impact on the Architectonic Heritage When Using Replicas of 16th Century Weapons

PubMed Central

Lloret, Angel Tomas; Sendra, Sandra; Louis Cereceda, Miguel

2017-01-01

The recreation of historical battles next to old buildings, walls, churches, fortifications or historical facades belonging to the historical heritage of a city, has always been a source of controversy and discussion. In the absence of a clear legislation about how these buildings can be affected by the use of blunderbusses and pyrotechnics, it is necessary to carry out practical experiments to test the effect of these celebrations on these buildings. For this reason, this paper presents a set of practical experiments where the vibroacoustic effect of using weapons such as blunderbusses and harquebuses is analyzed. To gather these measurements, we have used several sound level meters and 3-axis accelerometers placed on the facade of an old building. The tests have been carried out at the Moors and Christians festival of Villajoyosa (Spain) which is internationally famous for this festival. In order to carry out the tests, six harquebusiers shot their firearms and the sensors placed along the facade of the building at different height collected the data. The results of these devices allow us to study the vibroacoustic impact on the facade depending on the height. PMID:28805738

The Next-Generation Goddard Convective-Stratiform Heating Algorithm: New Retrievals for Tropical and Extra-tropical Environments

NASA Astrophysics Data System (ADS)

Lang, S. E.; Tao, W. K.; Iguchi, T.

2017-12-01

The Goddard Convective-Stratiform Heating (or CSH) algorithm has been used to estimate cloud heating over the global Tropics using TRMM rainfall data and a set of look-up-tables (LUTs) derived from a series of multi-week cloud-resolving model (CRM) simulations using the Goddard Cumulus Ensemble model (GCE). These simulations link satellite observables (i.e., surface rainfall and stratiform fraction) with cloud heating profiles, which are not directly observable. However, with the launch of GPM in 2014, the range over which such algorithms can be applied has been extended from the Tropics into higher latitudes, including cold season and synoptic weather systems. In response, the CSH algorithm and its LUTs have been revised both to improve the retrievals in the Tropics as well as expand retrievals to higher latitudes. For the Tropics, the GCE simulations used to build the LUTs were upgraded using larger 2D model domains (512 vs 256 km) and a new, improved Goddard 4-ice scheme as well as expanded with additional cases (4 land and 6 ocean in total). The new tropical LUTs are also re-built using additional metrics. Besides surface type, conditional rain intensity and stratiform fraction, the new LUTs incorporate echo top heights and low-level (0-2 km) vertical reflectivity gradients. CSH retrievals in the Tropics based on the new LUTs show significant differences from previous iterations using TRMM data or the old LUT metrics. For the Extra-tropics, 6 NU-WRF simulations of synoptic events (3 East Coast and 3 West Coast), including snow, were used to build new extra-tropical CSH LUTs. The LUT metrics for the extra-tropics are based on radar characteristics and freezing level height. The extra-tropical retrievals are evaluated with a self-consistency check approach using the model heating as `truth,' and freezing level height is used to transition CSH retrievals from the Tropics to Extra-tropics. Retrieved zonal average heating structures in the Extra-tropics are presented and show distinct differences from those in the Tropics.

Ecological analysis of secular trends in low birth weight births and adult height in Japan.

PubMed

Morisaki, Naho; Urayama, Kevin Yuji; Yoshii, Keisuke; Subramanian, S V; Yokoya, Susumu

2017-10-01

Japan, which currently maintains the highest life expectancy in the world and has experienced an impressive gain in adult height over the past century, has suffered a dramatic twofold increase in low birth weight (LBW) births since the 1970s. We observed secular trends in birth characteristics using 64 115 249 live births included the vital statistics (1969-2014), as well as trends in average height among 3 145 521 adults born between 1969 and 1996, included in 79 surveys conducted among a national, subnational or community population in Japan. LBW rates exhibited a U-shaped pattern showing reductions until 1978-1979 (5.5%), after which it increased. Conversely, average adult height peaked for those born during the same period (men, 171.5 cm; women, 158.5 cm), followed by a reduction over the next 20 years. LBW rate and adult height showed a strong inverse correlation (men, r=-0.98; women, r=-0.88). A prediction model based on birth and economical characteristics estimated the national average of adult height would continue to decline, to 170.0cm (95% CI 169.6 to 170.3) for men and 157.9cm (95% CI 157.5 to 158.3) for women among those born in 2014. Adult height in Japan has started to decline for those born after 1980, a trend that may be attributed to increases in LBW births over time. Considering the known association between shorter adult height and adverse health outcomes, evidence of population-level decline in adult health due to long-term consequences of increasing LBW births in Japan is anticipated. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Modelling of energy consumption at construction of high-rise buildings

NASA Astrophysics Data System (ADS)

Korol, Elena; Korol, Oleg

2018-03-01

High-rise building structures in the course of its erection suppose primary use of methods provided for erection, concrete and external finishing works. Erection works do not differ significantly from usual ones: traditional equipment, accessories and techniques are used which are based on erection of structures in project position using a crane. Structures to be assembled in building frame include steel columns and beams, wall panels, form elements of columns, walls and floor structures. We can note heightened attention to operational control for quality of erection, but it is attributable to all works in the course of high-rise construction. During high-rise erection by means of cast in-situ reinforced concrete all formworks to be used do not have any special differences except systems specially designed for high-rise erection using sliding formwork or vertical traveling forms. In these systems special attention is paid to safety of elevated works. Working methods of placement and curing of concrete and structures as a whole remain traditional - the requirements for controlling such operations become toughened. The most evident differences in high-rise erection with regard to equipment, machinery and accessories used are in means provided for load transportation and safety of works at heights. Particularity of internal finishing works which are also obligatory during construction of skyscrapers allows not considering them in as technological differences from usual construction as far as the «height» of its execution is limited by height of particular floor and determined by price and building class.

Sexual Orientation, Objective Height, and Self-Reported Height.

PubMed

Skorska, Malvina N; Bogaert, Anthony F

2017-01-01

Studies that have used mostly self-reported height have found that androphilic men and women are shorter than gynephilic men and women, respectively. This study examined whether an objective height difference exists or whether a psychosocial account (e.g., distortion of self-reports) may explain these putative height differences. A total of 863 participants, recruited at a Canadian university, the surrounding region, and through lesbian, gay, bisexual, and transgender (LGBT) events across Canada, self-reported their height and had their height measured. Androphilic men were shorter, on average, than gynephilic men. There was no objective height difference between gynephilic, ambiphilic, and androphilic women. Self-reported height, statistically controlling for objective height, was not related to sexual orientation. These findings are the first to show an objective height difference between androphilic and gynephilic men. Also, the findings suggest that previous studies using self-reported height found part of a true objective height difference between androphilic and gynephilic men. These findings have implications for existing biological theories of men's sexual orientation development.

Site index curves for Douglas-fir in New Mexico

Treesearch

Carleton B. Edminster; Lewis H. Jump

1976-01-01

Presents a figure, table, and FORTRAN subroutine for estimating site indexes for Douglas-fir stands in New Mexico. Site index is expressed as the average height of dominant trees at a breast-height age of 100 years.

Short stature

MedlinePlus

... SD) or more below the average height for children of the same sex and age Below the 2.3rd percentile on ... Compare your child's height and weight to other children of the same age and sex. Talk with you if you are worried that ...

Using Combination of Planar and Height Features for Detecting Built-Up Areas from High-Resolution Stereo Imagery

NASA Astrophysics Data System (ADS)

Peng, F.; Cai, X.; Tan, W.

2017-09-01

Within-class spectral variation and between-class spectral confusion in remotely sensed imagery degrades the performance of built-up area detection when using planar texture, shape, and spectral features. Terrain slope and building height are often used to optimize the results, but extracted from auxiliary data (e.g. LIDAR data, DSM). Moreover, the auxiliary data must be acquired around the same time as image acquisition. Otherwise, built-up area detection accuracy is affected. Stereo imagery incorporates both planar and height information unlike single remotely sensed images. Stereo imagery acquired by many satellites (e.g. Worldview-4, Pleiades-HR, ALOS-PRISM, and ZY-3) can be used as data source of identifying built-up areas. A new method of identifying high-accuracy built-up areas from stereo imagery is achieved by using a combination of planar and height features. The digital surface model (DSM) and digital orthophoto map (DOM) are first generated from stereo images. Then, height values of above-ground objects (e.g. buildings) are calculated from the DSM, and used to obtain raw built-up areas. Other raw built-up areas are obtained from the DOM using Pantex and Gabor, respectively. Final high-accuracy built-up area results are achieved from these raw built-up areas using the decision level fusion. Experimental results show that accurate built-up areas can be achieved from stereo imagery. The height information used in the proposed method is derived from stereo imagery itself, with no need to require auxiliary height data (e.g. LIDAR data). The proposed method is suitable for spaceborne and airborne stereo pairs and triplets.

Pollutant Dilution and Diffusion in Urban Street Canyon Neighboring Streets

NASA Astrophysics Data System (ADS)

Sun, Z.; Fu, Zh. M.

2011-09-01

In the present study we investigated the airflow patterns and air quality of a series of typical street canyon combinations, developed a mass balance model to determine the local pollutant dilution rate, and discuss the impact of upstream canyon on the air quality of downstream canyon. The results indicated that the geometrical size of upstream and downstream buildings have significant impacts on the ambient airflow patterns. The pollution distribution within the canyons varies with different building combinations and flow patterns. Within the upstream canyon, pollution always accumulates to the low building side for non-symmetrical canyon, and for symmetrical canyon high level of pollution occurs at the leeward side. The height of the middle and downstream buildings can evidently change the pollutant dispersion direction during the transport process. Within the polluted canyon, the pollutant dilution rate (PDR) also varies with different street canyon combinations. The highest PDR is observed when the upstream buildings are both low buildings no matter the height of downstream building. However, the two cases are likely to contribution pollution to the downstream canyon. The H-L-H combination is mostly against local pollution remove, while the L-H-L case is considered the best optimistic building combination with both the ability of diluting local pollution and not remarkably decreasing air quality of downstream canyon. The current work is expected instructive for city designers to optimize traffic patterns under typical existing geometry or in the development of urban geometry modification for air quality control.

Inheritance of height and maturity in crosses between pearl millet landraces and inbred Tift 85DB.

PubMed

Wilson, J P; Burton, G W; Bondari, K

1990-11-01

Over 300 landraces of pearl millet were collected in Burkina Faso and grown at the Coastal Plain Experiment Station in Tifton/GA. At Tifton, these landraces are predominantly tall and late-maturing. The photoperiod requirements of these landraces hinder evaluation of their performance in the field and their use in breeding programs. A conversion program has been initiated to transfer genes for dwarf stature and early flowering into the tall, late-maturing landraces. The inbred Tift 85DB is being used as a donor of genes for the dwarf and early characteristics, and was crossed to nine randomly selected landraces from Burkina Faso. The parents, F1, F2, and backcrosses to each parent were grown in the field and evaluated for plant height at anthesis and time in days from planting to anthesis. In general, plant height of F1s was taller than the tallest parent, and in all crosses the maturity of F1s was intermediate between the parents. Numbers of loci conferring height varied among crosses, ranging from 0 to 9.6, and averaged 1.6. Estimated numbers of loci conferring maturity ranged from 0 to 12.8 and averaged 3.4. Broad-sense heritability estimates for height and maturity averaged 60.2 and 65.7%, respectively. Corresponding narrow-sense estimates averaged 23.8 and 48.2%. Joint scaling tests revealed that additive-genetic effects were highly significant for both traits, but dominance and epistatic-genetic effects contributed to the inheritance of each trait in some crosses. The low gene numbers, high heritability estimates, and preponderance of additive-genetic effects suggest that selection for these traits should be effective.

Building 5 Manufacturing Branch. Explore@NASAGoddard celebrates

NASA Image and Video Library

2015-09-26

Building 5 Manufacturing Branch. Explore@NASAGoddard celebrates the 25th anniversary of the launch of the Hubble Space Telescope. All areas of Goddard’s research – Earth science, heliophysics, planetary science, astrophysics, and engineering and technology – will be presented, as each discipline plays a critical part in NASA's ongoing journey to reach new heights.

Sound Diffraction Around Movable Partitions in Teaching Spaces. Education Building Report 1.

ERIC Educational Resources Information Center

Choudhury, N. K. D.

This study concerns the diffraction of sound around flexible partitions used in teaching spaces. It includes a comprehensive study of the acoustical conditions in several school buildings in India, Malaysia, Singapore, and Sri Lanka. The noise reduction properties of some typical partitions the minimum height of the partition between two teaching…

Effect of maternal height on caesarean section and neonatal mortality rates in sub-Saharan Africa: An analysis of 34 national datasets.

PubMed

Arendt, Esther; Singh, Neha S; Campbell, Oona M R

2018-01-01

The lifecycle perspective reminds us that the roots of adult ill-health may start in-utero or in early childhood. Nutritional and infectious disease insults in early life, the critical first 1000 days, are associated with stunting in childhood, and subsequent short adult stature. There is limited or no opportunity for stunted children above 2 years of age to experience catch-up growth. Some previous research has shown short maternal height to lead to adverse birth outcomes. In this paper, we document the association between maternal height and caesarean section, and between maternal height and neonatal mortality in 34 sub-Saharan African countries. We also explore the appropriate height cut-offs to use. Our paper contributes arguments to support a focus on preventing non-communicable risk factors, namely early childhood under-nutrition, as part of the fight to reduce caesarean section rates and other adverse maternal and newborn health outcomes, particularly neonatal mortality. We focus on the Sub-Saharan Africa region because it carries the highest burden of maternal and neonatal ill-health. We used the most recent Demographic and Health Survey for 34 sub-Saharan African countries. The distribution of heights of women who had given birth in the 5 years before the survey was explored. We adopted the following cut-offs: Very Short (<145.0cm), Short (145.0-149.9cm), Short-average (150.0-154.9cm), Average (155.0-159.9cm), Average-tall (160.0-169.9cm) and Tall (≥170.0cm). Multivariate logistic regression was used to assess the contribution of maternal stature to the odds ratio of caesarean section delivery, adjusting for other exposures, such as age at index birth, residence, maternal BMI, maternal education, wealth index quintile, previous caesarean section, multiple birth, birth order and country of survey. We also look at its contribution to neonatal mortality adjusting for age at index birth, residence, maternal BMI, maternal education, wealth index quintile, multiple birth, birth order and country of survey. There was a gradual increase in the rate of caesarean section with decreasing maternal height. Compared to women of Average height (155.0-159.9cm), taller women were protected. The adjusted odds ratio (aOR) for Tall women was 0.67 (95% CI:0.52-0.87) and for Average-tall women was 0.78 (95% CI:0.69-0.89). Compared to women of Average height, shorter women were at increased risk. The aOR for Short-average women was 1.19 (95% CI:1.03-1.37), for Short women was 2.06 (95% CI:1.71-2.48), and for Very Short women was 2.50 (95% CI:1.85-3.38). There was evidence that compared to Average height women, Very Short and Short women had increased odds of experiencing a neonatal death aOR = 1.95 (95% CI 1.17-3.25) and aOR = 1.66 (95% CI 1.20-2.28) respectively. When we focused on the period of highest risk, the day of delivery and first postnatal day, these aORs increased to 2.36 (95% CI 1.57-3.55) and 2.34 (95% CI 1.19-4.60) respectively. The aORs for the first week of life (early neonatal mortality) were 1.90 (95% CI 1.07-3.36) and 1.83 (95% CI 1.30-2.59) respectively. Short stature is associated with an increased prevalence of caesarean section and neonatal mortality, particularly on the newborn's first days. These results are even more striking because we know that caesarean section rates tend to be higher among wealthier and more educated women, who are often taller and that the same patterns may hold for neonatal survival; in such cases, adjusting for wealth, education and urban residence would attenuate these associations. Caesarean sections can be lifesaving operations; however, they cost the health system and families more, and are associated with worse health outcomes. We suggest that our findings be used to argue for policies targeting stunting in infant girls and potential catch-up growth in adolescence and early adulthood, aiming to increase their adult height and thus decrease their subsequent risk of experiencing caesarean section and adverse birth outcomes.

U.S. Geological Survey National Center, Reston, Virginia

USGS Publications Warehouse

,

1972-01-01

In 1917 the Geological Survey moved into the newly built Interior Building near the White House in Washington, D. C. Twenty years later a larger building was constructed nearby to house the expanding U. S. Department of the Interior. Height restrictions reduced the planned size of the new building, and the Geological Survey was compelled to remain in the older Interior Building now identified as the General Services Administration Building. Expansion of the Survey's programs, and particularly the overall government need for additional office space in downtown Washington, has resulted in the Survey's activities being presently housed in 30 different buildings, at 17 widely scattered locations throughout the Washington Metropolitan Area.

Influence of local parameters on the dispersion of traffic-related pollutants within street canyons

NASA Astrophysics Data System (ADS)

Karra, Styliani; Malki-Epshtein, Liora; Martin Hyde Collaboration

2011-11-01

Ventilation within urban cities and street canyons and the associated air quality is a problem of increasing interest in the last decades. It is important for to minimise exposure of the population to traffic-related pollutants at street level. The residence time of pollutants within the street canyons depends on the meteorological conditions such as wind speed and direction, geometry layout and local parameters (position of traffic lane within the street). An experimental study was carried out to investigate the influence of traffic lane position on the dispersion of traffic-related pollutants within different street canyons geometries: symmetrical (equal building heights on both sides of the street), non-symmetrical (uniform building heights but lower on one side of the street) and heterogeneous (non-uniform building heights on both sides of the street) under constant meteorological conditions. Laboratory experiments were carried out within a water channel and simultaneous measurements of velocity field and concentration scalar levels within and above the street canyons using PIV and PLIF techniques. Traffic -related emissions were simulated using a line emission source. Two positions were examined for all street geometries: line emission source was placed in the centre of the street canyon; line emission source was placed off the centre of the street. TSI Incorporated.

A Numerical Study on the Effects of Street‒canyon Aspect‒ratio on Reactive Pollutant Dispersion

NASA Astrophysics Data System (ADS)

Park, S. J.; Kim, J.

2014-12-01

In this study, the effects of street‒canyon aspect‒ratio on reactive pollutant dispersion were investigated using the coupled CFD‒chemistry model. For this, flow characteristics were analyzed first in street canyons with different aspect ratios and flow regimes were classified according to the building height. For each flow regime, dispersion characteristics were investigated in views of reactive pollutant concentration and VOCs‒NOX ratio. Finally, the relations between pollutant concentration and aspect ratio in urban street canyons were investigated. In the case of H/S = 1.0 (H is building height and S is street width), one clockwise‒rotating vortex appeared vertically and the reverse and outward flows were dominant near the street bottom. In the case of H/S = 2.0, two counter‒rotating vortices appeared vertically in the street canyon. The primary (secondary) vortex rotating clockwise (counterclockwise) was formed in upper (lower) layer. The flow patterns affected the reactive pollutant concentration in street canyons. As building height increased, mean concentration of NO decreased when one vortex was generated in street canyons and increased when two vortexes appeared in street canyons. O3 concentration showed almost contrasted tendency with those of NO because O3 was depleted by the NO titration.

NGEE Arctic Plant Traits: Shrub Transects, Kougarok Road Mile Marker 64, Seward Peninsula, Alaska, 2016

DOE Data Explorer

Verity Salmon; Colleen Iversen; Peter Thornton; Ma

2017-03-01

Transect data is from point center quarter surveys for shrub density performed in July 2016 at the Kougarok hill slope located at Kougarok Road, Mile Marker 64. For each sample point along the transects, moving averages for shrub density and shrub basal area are provided along with GPS coordinates, average shrub height and active layer depth. The individual height, basal area, and species of surveyed shrubs are also included. Data upload will be completed January 2017.

You can be too thin (but not too tall): Social desirability bias in self-reports of weight and height.

PubMed

Burke, Mary A; Carman, Katherine G

2017-11-01

Previous studies of survey data from the U.S. and other countries find that women tend to understate their body weight on average, while both men and women overstate their height on average. Social norms have been posited as one potential explanation for misreporting of weight and height, but lack of awareness of body weight has been suggested as an alternative explanation, and the evidence presented to date is inconclusive. This paper is the first to offer a theoretical model of self-reporting behavior for weight and height, in which individuals face a tradeoff between reporting an accurate weight (or height) and reporting a socially desirable weight (or height). The model generates testable implications that help us to determine whether self-reporting errors arise because of social desirability bias or instead reflect lack of awareness of body weight and/or other factors. Using data from the National Health and Nutrition Examination Survey (NHANES) from 1999 to 2010, we find that self-reports of weight offer robust evidence of social desirability bias. However, lack of awareness of weight may also contribute to self-reporting biases, and this factor appears to be more important within some demographic groups than others. Among both women and men, self-reports of height exhibit significant social desirability bias only among those of below-average height, and very few individuals underreport their height. Implied self-reports of BMI exhibit gender-specific patterns similar to those observed for self-reporting of weight, and the inferred social norms for BMI (20.8 for women and 24.8 for men) are within the "normal" range established by public health institutions. Determining why individuals misreport their weight has important implications for survey design as well as for clinical practice. For example, our findings suggest that health care providers might take additional steps to increase self-awareness of body weight. The framework also helps to explain previous findings that the degree of self-reporting bias in weight is stronger in telephone surveys than it is in in-person surveys. Copyright © 2017 Elsevier B.V. All rights reserved.

Comparison of dust-layer heights from active and passive satellite sensors

NASA Astrophysics Data System (ADS)

Kylling, Arve; Vandenbussche, Sophie; Capelle, Virginie; Cuesta, Juan; Klüser, Lars; Lelli, Luca; Popp, Thomas; Stebel, Kerstin; Veefkind, Pepijn

2018-05-01

Aerosol-layer height is essential for understanding the impact of aerosols on the climate system. As part of the European Space Agency Aerosol_cci project, aerosol-layer height as derived from passive thermal and solar satellite sensors measurements have been compared with aerosol-layer heights estimated from CALIOP measurements. The Aerosol_cci project targeted dust-type aerosol for this study. This ensures relatively unambiguous aerosol identification by the CALIOP processing chain. Dust-layer height was estimated from thermal IASI measurements using four different algorithms (from BIRA-IASB, DLR, LMD, LISA) and from solar GOME-2 (KNMI) and SCIAMACHY (IUP) measurements. Due to differences in overpass time of the various satellites, a trajectory model was used to move the CALIOP-derived dust heights in space and time to the IASI, GOME-2 and SCIAMACHY dust height pixels. It is not possible to construct a unique dust-layer height from the CALIOP data. Thus two CALIOP-derived layer heights were used: the cumulative extinction height defined as the height where the CALIOP extinction column is half of the total extinction column, and the geometric mean height, which is defined as the geometrical mean of the top and bottom heights of the dust layer. In statistical average over all IASI data there is a general tendency to a positive bias of 0.5-0.8 km against CALIOP extinction-weighted height for three of the four algorithms assessed, while the fourth algorithm has almost no bias. When comparing geometric mean height there is a shift of -0.5 km for all algorithms (getting close to zero for the three algorithms and turning negative for the fourth). The standard deviation of all algorithms is quite similar and ranges between 1.0 and 1.3 km. When looking at different conditions (day, night, land, ocean), there is more detail in variabilities (e.g. all algorithms overestimate more at night than during the day). For the solar sensors it is found that on average SCIAMACHY data are lower by -1.097 km (-0.961 km) compared to the CALIOP geometric mean (cumulative extinction) height, and GOME-2 data are lower by -1.393 km (-0.818 km).

Validity of total and segmental impedance measurements for prediction of body composition across ethnic population groups.

PubMed

Deurenberg, P; Deurenberg-Yap, M; Schouten, F J M

2002-03-01

To test the impact of body build factors on the validity of impedance-based body composition predictions across (ethnic) population groups and to study the suitability of segmental impedance measurements. Cross-sectional observational study. Ministry of Health and School of Physical Education, Nanyang Technological University, Singapore. A total of 291 female and male Chinese, Malays and Indian Singaporeans, aged 18-69, body mass index (BMI) 16.0-40.2 kg/ m2. Anthropometric parameters were measured in addition to impedance (100 kHz) of the total body, arms and legs. Impedance indexes were calculated as height2/impedance. Arm length (span) and leg length (sitting height), wrist and knee width were measured from which body build indices were calculated. Total body water (TBW) was measured using deuterium oxide dilution. Extra cellular water (ECW) was measured using bromide dilution. Body fat percentage was determined using a chemical four-compartment model. The bias of TBW predicted from total body impedance index (bias: measured minus predicted TBW) was different among the three ethnic groups, TBW being significantly underestimated in Indians compared to Chinese and Malays. This bias was found to be dependent on body water distribution (ECW/TBW) and parameters of body build, mainly relative (to height) arm length. After correcting for differences in body water distribution and body build parameters the differences in bias across the ethnic groups disappeared. The impedance index using total body impedance was better correlated with TBW than the impedance index of arm or leg impedance, even after corrections for body build parameters. The study shows that ethnic-specific bias of impedance-based prediction formulas for body composition is due mainly to differences in body build among the ethnic groups. This means that the use of 'general' prediction equations across different (ethnic) population groups without prior testing of their validity should be avoided. Total body impedance has higher predictive value than segmental impedance.

Pubertal Height Velocity and Associations with Pre-pubertal and Adult Heights in Cystic Fibrosis

PubMed Central

Zhang, Zhumin; Lindstrom, Mary J.; Lai, HuiChuan J.

2013-01-01

Objectives To test the hypothesis that pubertal peak height velocity (PHV) in cystic fibrosis (CF) has improved and is influenced by pre-pubertal growth and genetic potential. Study design PHV from 1862 children born in 1984–87 and documented in the 1986–2008 US CF Foundation Registry was determined by statistical modeling and classified into normal, delayed (2-SD > average age), attenuated (magnitude < 5th percentile), or both (D&A). Genetic potential for height was estimated by parental stature. Results PHV averaged 8.4 cm/y at age 14.0 y in boys and 7.0 cm/y at age 12.1 y in girls, ~6 mo delay and ~15% reduction compared with healthy children. PHV was normal in 60%, delayed in 9%, attenuated in 21% and D&A in 5%. Patients with delayed PHV reached similar adult height percentile (boys: 34th, girls: 46th) to those with normal PHV (boys: 33rd, girls: 34th); both were significantly taller than the attenuated (boys: 11th, girls: 19th) and D&A PHV subgroups (boys: 8th, girls: 14th). Pancreatic sufficient patients had taller pre-pubertal and adult heights but similar PHV compared with pancreatic insufficient or meconium ileus patients. Adjusting for genetic potential reduced adult height percentiles more in boys (25th to 16th) than girls (28th to 24th). Height at age 7 y, PHV age and magnitude, and parental stature significantly predicted adult height. Conclusions Pubertal PHV has improved in children with CF born after mid 1980s compared with older cohorts but remains below normal. Suboptimal pre-pubertal and pubertal growth led to adult height below genetic potential in CF. PMID:23535012

Determining the Average Age of School Plant Building Space.

ERIC Educational Resources Information Center

Uerling, Donald F.

1984-01-01

Presents a method for calculating the age of the space in a specific building inventory, and suggests some practical applications. A fourfold procedure is provided for finding the average age of total building space. (TE)

Persistent Monitoring of Urban Infrasound Phenomenology. Report 1: Modeling an Urban Environment for Acoustical Analyses using the 3-D Finite-Difference Time-Domain Program PSTOP3D

DTIC Science & Technology

2015-08-01

a definition of the building footprints with an associated height attribute. This would be enough information to construct an extruded building ...contract was undertaken with CyberCity 3D (2012), a commercial company located in El Segundo, CA, to construct the buildings . The company specializes in...visualization of planning functions. CyberCity 3D used 6 in. stereoscopic aerial photography to construct 3-D models of the buildings . These models were quite

Empirical parameterization of setup, swash, and runup

USGS Publications Warehouse

Stockdon, H.F.; Holman, R.A.; Howd, P.A.; Sallenger, A.H.

2006-01-01

Using shoreline water-level time series collected during 10 dynamically diverse field experiments, an empirical parameterization for extreme runup, defined by the 2% exceedence value, has been developed for use on natural beaches over a wide range of conditions. Runup, the height of discrete water-level maxima, depends on two dynamically different processes; time-averaged wave setup and total swash excursion, each of which is parameterized separately. Setup at the shoreline was best parameterized using a dimensional form of the more common Iribarren-based setup expression that includes foreshore beach slope, offshore wave height, and deep-water wavelength. Significant swash can be decomposed into the incident and infragravity frequency bands. Incident swash is also best parameterized using a dimensional form of the Iribarren-based expression. Infragravity swash is best modeled dimensionally using offshore wave height and wavelength and shows no statistically significant linear dependence on either foreshore or surf-zone slope. On infragravity-dominated dissipative beaches, the magnitudes of both setup and swash, modeling both incident and infragravity frequency components together, are dependent only on offshore wave height and wavelength. Statistics of predicted runup averaged over all sites indicate a - 17 cm bias and an rms error of 38 cm: the mean observed runup elevation for all experiments was 144 cm. On intermediate and reflective beaches with complex foreshore topography, the use of an alongshore-averaged beach slope in practical applications of the runup parameterization may result in a relative runup error equal to 51% of the fractional variability between the measured and the averaged slope.

Comparison of the Atomic Oxygen Erosion Depth and Cone Height of Various Materials at Hyperthermal Energy

NASA Technical Reports Server (NTRS)

Waters, Deborah L.; Banks, Bruce A.; Thorson, Stephen D.; deGroh, Kim, K.; Miller, Sharon K.

2007-01-01

Atomic oxygen readily reacts with most spacecraft polymer materials exposed to the low Earth orbital (LEO) environment. If the atomic oxygen arrival comes from a fixed angle of impact, the resulting erosion will foster the development of a change in surface morphology as material thickness decreases. Hydrocarbon and halopolymer materials, as well as graphite, are easily oxidized and textured by directed atomic oxygen in LEO at energies of approx.4.5 eV. What has been curious is that the ratio of cone height to erosion depth is quite different for different materials. The formation of cones under fixed direction atomic oxygen attack may contribute to a reduction in material tensile strength in excess of that which would occur if the cone height to erosion depth ratio was very low because of greater opportunities for crack initiation. In an effort to understand how material composition affects the ratio of cone height to erosion depth, an experimental investigation was conducted on 18 different materials exposed to a hyperthermal energy directed atomic oxygen source (approx.70 eV). The materials were first salt-sprayed to provide microscopic local areas that would be protected from atomic oxygen. This allowed erosion depth measurements to be made by scanning microscopy inspection. The polymers were then exposed to atomic oxygen produced by an end Hall ion source that was operated on pure oxygen. Samples were exposed to an atomic oxygen effective fluence of 1.0x10(exp 20) atoms/sq cm based on Kapton H polyimide erosion. The average erosion depth and average cone height were determined using field emission scanning electron microscopy (FESEM). The experimental ratio of average cone height to erosion depth is compared to polymer composition and other properties.

Characteristics of nocturnal coastal boundary layer in Ahtopol based on averaged SODAR profiles

NASA Astrophysics Data System (ADS)

Barantiev, Damyan; Batchvarova, Ekaterina; Novitzky, Mikhail

2014-05-01

The ground-based remote sensing instruments allow studying the wind regime and the turbulent characteristics of the atmosphere with height, achieving new knowledge and solving practical problems, such as air quality assessments, mesoscale models evaluation with high resolution data, characterization of the exchange processes between the surface and the atmosphere, the climate comfort conditions and the risk for extreme events, etc. Very important parameter in such studies is the height of the atmospheric boundary layer. Acoustic remote sensing data of the coastal atmospheric boundary layer were explored based on over 4-years continuous measurements at the meteorological observatory of Ahtopol (Bulgarian Southern Black Sea Coast) under Bulgarian - Russian scientific agreement. Profiles of 12 parameters from a mid-range acoustic sounding instrument type SCINTEC MFAS are derived and averaged up to about 600 m according filtering based on wind direction (land or sea type of night fowls). From the whole investigated period of 1454 days with 10-minute resolution SODAR data 2296 profiles represented night marine air masses and 1975 profiles represented the night flow from land during the months May to September. Graphics of averaged profiles of 12 SODAR output parameters with different availability of data in height are analyzed for both cases. A marine boundary-layer height of about 300 m is identified in the profiles of standard deviation of vertical wind speed (σw), Turbulent Kinetic Energy (TKE) and eddy dissipation rate (EDR). A nocturnal boundary-layer height of about 420 m was identified from the profiles of the same parameters under flows from land condition. In addition, the Buoyancy Production (BP= σw3/z) profiles were calculated from the standard deviation of the vertical wind speed and the height z above ground.

Atomic force microscopic study of step bunching and macrostep formation during the growth of L-arginine phosphate monohydrate single crystals

NASA Astrophysics Data System (ADS)

Sangwal, K.; Torrent-Burgues, J.; Sanz, F.; Gorostiza, P.

1997-02-01

The experimental results of the formation of step bunches and macrosteps on the {100} face of L-arginine phosphate monohydrate crystals grown from aqueous solutions at different supersaturations studied by using atomic force microscopy are described and discussed. It was observed that (1) the step height does not remain constant with increasing time but fluctuates within a particular range of heights, which depends on the region of step bunches, (2) the maximum height and the slope of bunched steps increases with growth time as well as supersaturation used for growth, and that (3) the slope of steps of relatively small heights is usually low with a value of about 8° and does not depend on the region of formation of step bunches, but the slope of steps of large heights is up to 21°. Analysis of the experimental results showed that (1) at a particular value of supersaturation the ratio of the average step height to the average step spacing is a constant, suggesting that growth of the {100} face of L-arginine phosphate monohydrate crystals occurs by direct integration of growth entities to growth steps, and that (2) the formation of step bunches and macrosteps follows the dynamic theory of faceting, advanced by Vlachos et al.

Childhood growth and breast cancer.

PubMed

De Stavola, B L; dos Santos Silva, I; McCormack, V; Hardy, R J; Kuh, D J; Wadsworth, M E J

2004-04-01

Adult height is known to be positively associated with breast cancer risk. The mechanism underlying this association is complex, since adult height is positively correlated with age at menarche, which in turn is negatively associated with breast cancer risk. The authors used prospective data from a British cohort of 2,547 girls followed from birth in 1946 to the end of 1999 to examine breast cancer risk in relation to childhood growth. As expected, adult height was positively associated with age at menarche and breast cancer. In childhood, cases were taller and leaner, on average, than noncases. Significant predictors of breast cancer risk in models containing all components of growth were height velocity at age 4-7 years (for a one-standard-deviation increase, odds ratio (OR) = 1.54, 95% confidence interval (CI): 1.13, 2.09) and age 11-15 years (OR = 1.29, 95% CI: 0.97, 1.71) and body mass index velocity (weight (kg)/height (m)(2)/year) at age 2-4 years (OR = 0.63, 95% CI: 0.48, 0.83). The effects of these variables were particularly marked in women with early menarche (age <12.5 years). These findings suggest that women who grow faster in childhood and reach an adult height above the average for their menarche category are at particularly increased risk of breast cancer.

Relationship between food insecurity and nutritional status of Brazilian children under the age of five.

PubMed

Santos, Leonardo Pozza dos; Gigante, Denise Petrucci

2013-12-01

The aim of this study was to investigate the relationship between food insecurity and nutritional status of Brazilian children. The National Demographic and Health Survey 2006 database is available on the worldwide web. Thus, the analyzed variables were obtained in this study, including nutritional indices, food insecurity and other socioeconomic and demographic variables. The height-for-age, weight-for-age and weight-for-height indices were evaluated as the Z-score of the World Health Organization reference curves. Food insecurity was defined by using the Brazilian Food Insecurity Scale. Averages of three indices according to the presence of food insecurity were analyzed, including other variables. Linear regression evaluated the effect of food insecurity on the Z-score of the three nutritional indices. The sample included 4,817 children, out of whom 7% had deficit in height, 7% were overweight and 47% had food insecurity. It was found that the average of height-for-age, weight-for-age and weight-for-height were -0.31, 0.12 and 0.40, respectively, being lower among children with food insecurity. The regression analysis showed that children living with some level of food insecurity have worse rates of height-for-age, even controlling for demographic and socioeconomic factors.

Buildings 7 & 29. Explore@NASAGoddard celebrates the 25th annive

NASA Image and Video Library

2015-09-26

Buildings 7 & 29. Explore@NASAGoddard celebrates the 25th anniversary of the launch of the Hubble Space Telescope. All areas of Goddard’s research – Earth science, heliophysics, planetary science, astrophysics, and engineering and technology – will be presented, as each discipline plays a critical part in NASA's ongoing journey to reach new heights.

Buildings 7 & 29. Explore@NASAGoddard celebrates the 25th annive

NASA Image and Video Library

2015-09-25

Buildings 7 & 29. Explore@NASAGoddard celebrates the 25th anniversary of the launch of the Hubble Space Telescope. All areas of Goddard’s research – Earth science, heliophysics, planetary science, astrophysics, and engineering and technology – will be presented, as each discipline plays a critical part in NASA's ongoing journey to reach new heights.

Final Report on Contract F30602-91-C-0037 (Massachusetts University)

DTIC Science & Technology

1991-01-01

multiple levels of rmpresetion. Recognitio graphs control both hypothnes tranaoe-mation and hypothesm venlcatso., as shown in Figure 4, The premise 9...knowledge base, one that estimates distance based on the apparent width of a window and the estimated angle of the building face , and a second that...the orientation of the building face is not needed to estimate distance from the building’s height). Of course, since any two points on the object

Predicting the microbial exposure risks in urban floods using GIS, building simulation, and microbial models.

PubMed

Taylor, Jonathon; Biddulph, Phillip; Davies, Michael; Lai, Ka man

2013-01-01

London is expected to experience more frequent periods of intense rainfall and tidal surges, leading to an increase in the risk of flooding. Damp and flooded dwellings can support microbial growth, including mould, bacteria, and protozoa, as well as persistence of flood-borne microorganisms. The amount of time flooded dwellings remain damp will depend on the duration and height of the flood, the contents of the flood water, the drying conditions, and the building construction, leading to particular properties and property types being prone to lingering damp and human pathogen growth or persistence. The impact of flooding on buildings can be simulated using Heat Air and Moisture (HAM) models of varying complexity in order to understand how water can be absorbed and dry out of the building structure. This paper describes the simulation of the drying of building archetypes representative of the English building stock using the EnergyPlus based tool 'UCL-HAMT' in order to determine the drying rates of different abandoned structures flooded to different heights and during different seasons. The results are mapped out using GIS in order to estimate the spatial risk across London in terms of comparative flood vulnerability, as well as for specific flood events. Areas of South and East London were found to be particularly vulnerable to long-term microbial exposure following major flood events. Copyright © 2012 Elsevier Ltd. All rights reserved.

View northnortheast of drydock no. 2 and its portal cranes. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View north-northeast of drydock no. 2 and its portal cranes. Main crane, 50 long tons capacity/maximum height 118 "2", is at left; whip crane, 53 long tons capacity maximum height 173 "8" is at center; auxiliary crane, 15 long tons capacity/maximum height 161 "0" is at right. Building at left is the turret shed. The vessel at the lower right of the photograph is a receiving ship formerly used for processing and temporary housing of naval personnel. - Naval Base Philadelphia-Philadelphia Naval Shipyard, Drydock No. 2, League Island, Philadelphia, Philadelphia County, PA

The influence of street layouts and viaduct settings on daily carbon monoxide exposure and intake fraction in idealized urban canyons.

PubMed

Hang, Jian; Luo, Zhiwen; Wang, Xuemei; He, Lejian; Wang, Baomin; Zhu, Wei

2017-01-01

Environmental concerns have been raised on the adverse health effects of vehicle emissions in micro-scale traffic-crowded street canyons, especially for pedestrians and residents living in near-road buildings. Viaduct design is sometimes used to improve transportation efficiency but possibly affects urban airflow and the resultant exposure risk, which have been rarely investigated so far. The personal intake fraction (P_IF) is defined as the average fraction of total emissions that is inhaled by each person of a population (1 ppm = 1 × 10 -6 ), and the daily carbon monoxide (CO) pollutant exposure (E t ) is estimated by multiplying the average concentration of a specific micro-environment within one day. As a novelty, by considering time activity patterns and breathing rates in various micro-environments for three age groups, this paper introduces IF and E t into computational fluid dynamic (CFD) simulation to quantify the impacts of street layouts (street width/building height W/H = 1, 1.5, 2), source location, viaduct settings and noise barriers on the source-exposure correlation when realistic CO sources are defined. Narrower streets experience larger P_IF (1.51-5.21 ppm) and CO exposure, and leeward-side buildings always attain higher vehicular pollutant exposure than windward-side. Cases with a viaduct experience smaller P_IF (3.25-1.46 ppm) than cases without a viaduct (P_IF = 5.21-2.23 ppm) if the single ground-level CO source is elevated onto the viaduct. With two CO sources (both ground-level and viaduct-level), daily CO exposure rises 2.80-3.33 times but P_IF only change slightly. Noise barriers above a viaduct raise concentration between barriers, but slightly reduce vehicular exposure in near-road buildings. Because people spend most of their time indoors, vehicular pollutant exposure within near-road buildings can be 6-9 times that at pedestrian level. Although further studies are still required to provide practical guidelines, this paper provides effective methodologies to quantify the impacts of street/viaduct configurations on human exposure for urban design purpose. Copyright © 2016 Elsevier Ltd. All rights reserved.

Statistical trend analysis and extreme distribution of significant wave height from 1958 to 1999 - an application to the Italian Seas

NASA Astrophysics Data System (ADS)

Martucci, G.; Carniel, S.; Chiggiato, J.; Sclavo, M.; Lionello, P.; Galati, M. B.

2009-09-01

The study is a statistical analysis of sea states timeseries derived using the wave model WAM forced by the ERA-40 dataset in selected areas near the Italian coasts. For the period 1 January 1958 to 31 December 1999 the analysis yields: (i) the existence of a negative trend in the annual- and winter-averaged sea state heights; (ii) the existence of a turning-point in late 70's in the annual-averaged trend of sea state heights at a site in the Northern Adriatic Sea; (iii) the overall absence of a significant trend in the annual-averaged mean durations of sea states over thresholds; (iv) the assessment of the extreme values on a time-scale of thousand years. The analysis uses two methods to obtain samples of extremes from the independent sea states: the r-largest annual maxima and the peak-over-threshold. The two methods show statistical differences in retrieving the return values and more generally in describing the significant wave field. The study shows the existence of decadal negative trends in the significant wave heights and by this it conveys useful information on the wave climatology of the Italian seas during the second half of the 20th century.

Height, education and later-life cognition in Latin America and the Caribbean.

PubMed

Maurer, Jürgen

2010-07-01

Building on previous evidence from the U.S., this study investigates the relationship between anthropometric markers (height and knee height), early-life conditions, education, and cognitive function in later life among urban elderly from Latin America and the Caribbean. I document a positive association between height and later-life cognitive function, which is larger for women than for men. This sex difference increases when I address potential feedback effects from mid- and later-life circumstances on stature by using knee height as an instrument for height. Specifically, while the estimates for women remain largely unchanged, I only find a diminished and statistically insignificant association between instrumented height and later-life cognition for men. This finding suggests that at least part of the association between height and later-life cognition among men may stem from common third factors that are correlated with both height and later-life cognition, such as adverse occupational exposures or health events during mid- and later life. Extended models that also include education further diminish the association between height and later-life cognition. Education displays strong positive gradients with the employed measures of childhood circumstances - including height - which points to education as a potential pathway linking early-life conditions and later-life cognitive function. 2010 Elsevier B.V. All rights reserved.

Height-reducing variants and selection for short stature in Sardinia

PubMed Central

Mulas, Antonella; Steri, Maristella; Busonero, Fabio; Marcus, Joseph H.; Marongiu, Michele; Maschio, Andrea; Ortega Del Vecchyo, Diego; Floris, Matteo; Meloni, Antonella; Delitala, Alessandro; Concas, Maria Pina; Murgia, Federico; Biino, Ginevra; Vaccargiu, Simona; Nagaraja, Ramaiah; Lohmueller, Kirk E.; Timpson, Nicholas J.; Soranzo, Nicole; Tachmazidou, Ioanna; Dedoussis, George; Zeggini, Eleftheria; Uzzau, Sergio; Jones, Chris; Lyons, Robert; Angius, Andrea; Abecasis, Gonçalo R.; Novembre, John; Schlessinger, David; Cucca, Francesco

2015-01-01

We report sequencing-based whole-genome association analyses to evaluate the impact of rare and founder variants on stature in 6,307 individuals on the island of Sardinia. We identified two variants with large effects. One is a stop codon in the GHR gene, relatively frequent in Sardinia (0.87% vs <0.01% elsewhere), which in homozygosity causes the short stature Laron syndrome. We find that it reduces height in heterozygotes by an average of 4.2 cm (−0.64 s.d). The other variant, in the imprinted KCNQ1 gene (MAF = 7.7% vs <1% elsewhere) reduces height by an average of 1.83 cm (−0.31 s.d.) when maternally inherited. Additionally, polygenic scores indicate that known height-decreasing alleles are at systematically higher frequency in Sardinians than would be expected by genetic drift. The findings are consistent with selection toward shorter stature in Sardinia and a suggestive human example of the proposed “island effect” reducing the size of large mammals. PMID:26366551

Comparison of analytical methods for calculation of wind loads

NASA Technical Reports Server (NTRS)

Minderman, Donald J.; Schultz, Larry L.

1989-01-01

The following analysis is a comparison of analytical methods for calculation of wind load pressures. The analytical methods specified in ASCE Paper No. 3269, ANSI A58.1-1982, the Standard Building Code, and the Uniform Building Code were analyzed using various hurricane speeds to determine the differences in the calculated results. The winds used for the analysis ranged from 100 mph to 125 mph and applied inland from the shoreline of a large open body of water (i.e., an enormous lake or the ocean) a distance of 1500 feet or ten times the height of the building or structure considered. For a building or structure less than or equal to 250 feet in height acted upon by a wind greater than or equal to 115 mph, it was determined that the method specified in ANSI A58.1-1982 calculates a larger wind load pressure than the other methods. For a building or structure between 250 feet and 500 feet tall acted upon by a wind rangind from 100 mph to 110 mph, there is no clear choice of which method to use; for these cases, factors that must be considered are the steady-state or peak wind velocity, the geographic location, the distance from a large open body of water, and the expected design life and its risk factor.

Three-dimensional Radar Imaging of a Building

DTIC Science & Technology

2012-12-01

spotlight configuration and H-V ( cross ) polarization as seen from two different aspect angles. The feature colors correspond to their brightness... cross - ranges but at different heights. This effect may create significant confusion in image interpretation and result in missed target detections...over a range of azimuth angles ( centered at  = 0°) and elevation angles ( centered at 0), creating cross -range and height resolution, while

Optimisation of Substrate Angles for Multi-material and Multi-functional Inkjet Printing.

PubMed

Vaithilingam, Jayasheelan; Saleh, Ehab; Wildman, Ricky D; Hague, Richard J M; Tuck, Christopher J

2018-06-13

Three dimensional inkjet printing of multiple materials for electronics applications are challenging due to the limited material availability, inconsistencies in layer thickness between dissimilar materials and the need to expose the printed tracks of metal nanoparticles to temperature above 100 °C for sintering. It is envisaged that instead of printing a dielectric and a conductive material on the same plane, by printing conductive tracks on an angled dielectric surface, the required number of silver layers and consequently, the exposure of the polymer to high temperature and the build time of the component can be significantly reduced. Conductive tracks printed with a fixed print height (FH) showed significantly better resolution for all angles than the fixed slope (FS) sample where the print height varied to maintain the slope length. The electrical resistance of the tracks remained under 10Ω up to 60° for FH; whereas for the FS samples, the resistance remained under 10Ω for samples up to 45°. Thus by fixing the print height to 4 mm, precise tracks with low resistance can be printed at substrate angles up to 60°. By adopting this approach, the build height "Z" can be quickly attained with less exposure of the polymer to high temperature.

Apparatus and method for mounting photovoltaic power generating systems on buildings

DOEpatents

Russell, Miles Clayton [Lincoln, MA

2008-10-14

Rectangular PV modules (6) are mounted on a building roof (4) by mounting stands that are distributed in rows and columns. Each stand comprises a base plate (10) that rests on the building roof (4) and first and second brackets (12, 14) of different height attached to opposite ends of the base plate (10). Each bracket (12, 14) has dual members for supporting two different PV modules (6), and each PV module (6) has a mounting pin (84) adjacent to each of its four corners. Each module (6) is supported by attachment of two of its mounting pins (84) to different first brackets (12), whereby the modules (6) and their supporting stands are able to resist uplift forces resulting from high velocity winds without the base plates (10) being physically attached to the supporting roof structure (4). Preferably the second brackets (14) have a telescoping construction that permits their effective height to vary from less than to substantially the same as that of the first brackets (12).

Laser Metal Deposition as Repair Technology for a Gas Turbine Burner Made of Inconel 718

NASA Astrophysics Data System (ADS)

Petrat, Torsten; Graf, Benjamin; Gumenyuk, Andrey; Rethmeier, Michael

Maintenance, repair and overhaul of components are of increasing interest for parts of high complexity and expensive manufacturing costs. In this paper a production process for laser metal deposition is presented, and used to repair a gas turbine burner of Inconel 718. Different parameters for defined track geometries were determined to attain a near net shape deposition with consistent build-up rate for changing wall thicknesses over the manufacturing process. Spot diameter, powder feed rate, welding velocity and laser power were changed as main parameters for a different track size. An optimal overlap rate for a constant layer height was used to calculate the best track size for a fitting layer width similar to the part dimension. Deviations in width and height over the whole build-up process were detected and customized build-up strategies for the 3D sequences were designed. The results show the possibility of a near net shape repair by using different track geometries with laser metal deposition.

Relationships Between Countermovement Jump Ground Reaction Forces and Jump Height, Reactive Strength Index, and Jump Time.

PubMed

Barker, Leland A; Harry, John R; Mercer, John A

2018-01-01

Barker, LA, Harry, JR, and Mercer, JA. Relationships between countermovement jump ground reaction forces and jump height, reactive strength index, and jump time. J Strength Cond Res 32(1): 248-254, 2018-The purpose of this study was to determine the relationship between ground reaction force (GRF) variables to jump height, jump time, and the reactive strength index (RSI). Twenty-six, Division-I, male, soccer players performed 3 maximum effort countermovement jumps (CMJs) on a dual-force platform system that measured 3-dimensional kinetic data. The trial producing peak jump height was used for analysis. Vertical GRF (Fz) variables were divided into unloading, eccentric, amortization, and concentric phases and correlated with jump height, RSI (RSI = jump height/jump time), and jump time (from start to takeoff). Significant correlations were observed between jump height and RSI, concentric kinetic energy, peak power, concentric work, and concentric displacement. Significant correlations were observed between RSI and jump time, peak power, unload Fz, eccentric work, eccentric rate of force development (RFD), amortization Fz, amortization time, second Fz peak, average concentric Fz, and concentric displacement. Significant correlations were observed between jump time and unload Fz, eccentric work, eccentric RFD, amortization Fz, amortization time, average concentric Fz, and concentric work. In conclusion, jump height correlated with variables derived from the concentric phase only (work, power, and displacement), whereas Fz variables from the unloading, eccentric, amortization, and concentric phases correlated highly with RSI and jump time. These observations demonstrate the importance of countermovement Fz characteristics for time-sensitive CMJ performance measures. Researchers and practitioners should include RSI and jump time with jump height to improve their assessment of jump performance.

Anthropometric characteristics of primary school-aged children: accuracy of perception and differences by gender, age and BMI.

PubMed

Cattelino, E; Bina, M; Skanjeti, A M; Calandri, E

2015-11-01

Body perception has been mainly studied in adolescents and adults in relation to eating disorders and obesity because such conditions are usually associated with distortion in the perception of body size. The development of body perception in children was rather neglected despite the relevance of this issue in understanding the aetiology of health eating problems. The main aim of this study was to investigate body weight and body height perception in children by gender, age and body mass index (BMI), taking into account differences among underweight, healthy weight, overweight and obese children. A school-based sample of 572 Italian children (49% boys) aged 6-10 were involved in a cross-sectional survey. Current weight and height were measured by standard protocols, and BMI was calculated and converted in centile categories using the Italian growth curves for children. Perceived weight and height were assessed using visual methods (figures representing children of different weight and height). About a third of the children do not show to have an accurate perception of their weight and height (weight: 36%; height: 32%): as for weight, an error of underestimation prevails and as for height, an error of overestimation prevails. In general, children who have different weight and height from the average tend to perceive their physical characteristics closer to average. However, overweight children underestimate their weight much more than obese children. Distortions in the perception of their physical features, weight and height, appear to be related to the aesthetic models of Western culture. The tendency to underestimate weight, particularly in overweight children, has implications in interventions for health promotion and healthy lifestyle in school-aged children. © 2014 John Wiley & Sons Ltd.

47 CFR 90.307 - Protection criteria.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) and antenna height of the proposed land mobile base station and the ERP for the associated control...)). (a) Base stations operating on the frequencies available for land mobile use in any urbanized area...) For base stations having antenna heights between 152 and 914 meters (500-3000 feet) above average...

The value of shoe size for prediction of the timing of the pubertal growth spurt

PubMed Central

2011-01-01

Background Knowing the timing of the pubertal growth spurt of the spine, represented by sitting height, is essential for the prognosis and therapy of adolescent idiopathic scoliosis. There are several indicators that reflect growth or remaining growth of the patient. For example, distal body parts have their growth spurt earlier in adolescence, and therefore the growth of the foot can be an early indicator for the growth spurt of sitting height. Shoe size is a good alternative for foot length, since patients can remember when they bought new shoes and what size these shoes were. Therefore the clinician already has access to some longitudinal data at the first visit of the patient to the outpatient clinic. The aim of this study was to describe the increase in shoe size during adolescence and to determine whether the timing of the peak increase could be an early indicator for the timing of the peak growth velocity of sitting height. Methods Data concerning shoe sizes of girls and boys were acquired from two large shoe shops from 1991 to 2008. The longitudinal series of 242 girls and 104 boys were analysed for the age of the "peak increase" in shoe size, as well as the age of cessation of foot growth based on shoe size. Results The average peak increase in shoe size occurred at 10.4 years (SD 1.1) in girls and 11.5 years (SD 1.5) in boys. This was on average 1.3 years earlier than the average peak growth velocity of sitting height in girls, and 2.5 years earlier in boys. The increase in shoe size diminishes when the average peak growth velocity of sitting height takes place at respectively 12.0 (SD 0.8) years in girls, and 13.7 (SD 1.0) years in boys. Conclusions Present data suggest that the course of the shoe size of children visiting the outpatient clinic can be a useful first tool for predicting the timing of the pubertal growth spurt of sitting height, as a representative for spinal length. This claim needs verification by direct comparison of individual shoe size and sitting height data and than a step forward can be made in clinical decision making regarding adolescent idiopathic scoliosis. PMID:21251310

Alliance for Sustainable Colorado Renovation Raises Its Energy Performance to New Heights, Commercial Building Energy Efficiency (Fact Sheet); Energy Efficiency & Renewable Energy (EERE)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The Alliance for Sustainable Colorado (The Alliance) is a nonprofit organization aiming to transform sustainability from vision to reality. Part of its mission is to change the operating paradigms of commercial building design to make them more sustainable. Toward that end The Alliance uses its headquarters, The Alliance Center at 1536 Wynkoop Street in Denver, as a living laboratory, conductingpilot studies of innovative commercial-building-design solutions for using and generating energy.

A Computational Fluid Dynamic (CFD) Simulation of PM10 Dispersion Caused by Rail Transit Construction Activity: A Real Urban Street Canyon Model.

PubMed

Wang, Yang; Zhou, Ying; Zuo, Jian; Rameezdeen, Raufdeen

2018-03-09

Particle emissions derived from construction activities have a significant impact on the local air quality, while the canyon effect with reduced natural ventilation contributes to the highest particulate pollution in urban environments. This study attempted to examine the effect of PM 10 emissions derived from the construction of a rail transit system in an urban street canyon. Using a 3D computational fluid dynamic (CFD) model based on a real street canyon with different height ratios, this study formulates the impact of height ratio and wind directions on the dispersion and concentration of PM 10 . The results indicate that parallel flow would cause the concentration of PM 10 at the end of the street canyons in all height ratios, and the trends in horizontal, vertical and lateral planes in all street canyons are similar. While in the condition of perpendicular flow, double-eddy circulations occur and lead to the concentration of PM 10 in the middle part of the street canyon and leeward of backwind buildings in all height ratios. Furthermore, perpendicular flow will cause the concentration of PM 10 to increase if the upwind buildings are higher than the backwind ones. This study also shows that the dispersion of PM 10 is strongly associated with wind direction in and the height ratios of the street canyons. Certain measures could, therefore, be taken to prevent the impact on people in terms of the PM 10 concentration and the heights of street canyons identified in this research. Potential mitigation strategies are suggested, include measurements below 4 m according to governmental regulations, dust shields, and atomized water.

The Effects of Temperature and CO2-induced Acidification on Skeletal Morphology of the Tropical Reef-building Coral Siderastrea siderea

NASA Astrophysics Data System (ADS)

Cobleigh, K.

2016-02-01

Coral reefs are threatened by increasing sea surface temperatures and decreasing surface seawater pH. Although numerous experimental studies have examined the effects of these global scale stressors on corals, few have quantified the effects of temperature and acidification on coral skeletal morphology. We conducted controlled laboratory experiments to investigate the effects of temperature (25, 28, 32°C) and CO2-induced ocean acidification (pCO2 = 324, 477, 604, 2553 µatm) on skeletal morphology of the highly resilient Caribbean reef-building coral Siderastrea siderea over a 95-day interval. Post-treatment S. siderea corallites from nearshore, backreef, and forereef colonies were imaged via stereo microscopy to evaluate impact of warming and acidification on corallite height and infilling. Both an increase and decrease in temperature relative to the control (i.e., near-present-day temperatures) resulted in increased corallite height but decreased skeletal infilling. In contrast, corals reared under the lowest (i.e., pre-industrial) and highest pCO2 treatments (i.e., extreme pCO2) exhibited both decreased corallite height and skeletal infilling relative to the control. We observed no difference in corallite height or infilling across reef zones, either within or across treatments. Interestingly, the warming projected for the end of the 21st century (32°C) resulted in increased corallite height and reduced corallite infilling. Acidification projected for the same interval (pCO2 = 604 µatm) also resulted in increased corallite height and decreased infilling. Collectively, our results suggest that these two global stressors will result in S. siderea corallites that are taller yet less infilled by the end of the 21st century. Changes in S. siderea arising from warming and acificiation may exacerbate observed declines in coral health across Caribbean reef systems.

A Computational Fluid Dynamic (CFD) Simulation of PM10 Dispersion Caused by Rail Transit Construction Activity: A Real Urban Street Canyon Model

PubMed Central

Wang, Yang; Zhou, Ying; Zuo, Jian

2018-01-01

Particle emissions derived from construction activities have a significant impact on the local air quality, while the canyon effect with reduced natural ventilation contributes to the highest particulate pollution in urban environments. This study attempted to examine the effect of PM10 emissions derived from the construction of a rail transit system in an urban street canyon. Using a 3D computational fluid dynamic (CFD) model based on a real street canyon with different height ratios, this study formulates the impact of height ratio and wind directions on the dispersion and concentration of PM10. The results indicate that parallel flow would cause the concentration of PM10 at the end of the street canyons in all height ratios, and the trends in horizontal, vertical and lateral planes in all street canyons are similar. While in the condition of perpendicular flow, double-eddy circulations occur and lead to the concentration of PM10 in the middle part of the street canyon and leeward of backwind buildings in all height ratios. Furthermore, perpendicular flow will cause the concentration of PM10 to increase if the upwind buildings are higher than the backwind ones. This study also shows that the dispersion of PM10 is strongly associated with wind direction in and the height ratios of the street canyons. Certain measures could, therefore, be taken to prevent the impact on people in terms of the PM10 concentration and the heights of street canyons identified in this research. Potential mitigation strategies are suggested, include measurements below 4 m according to governmental regulations, dust shields, and atomized water. PMID:29522495

An Architect Cicada in Brazilian Rainforest: Guyalna chlorogena (Walker).

PubMed

Béguin, C F

2017-04-01

To study the noteworthy nest building behavior of the nymph of the Brazilian Rainforest cicada Guyalna chlorogena (Walker) during the last year of its underground life, we monitored a large number of edifices, consisting of a vertical well (up to 1 m deep) with a turret (20 to 40 cm tall) on top, and we also performed experiments. We have shown that the buildings are occupied by a single nymph, male or female, which increases the height of its turret each night by about 3 cm, during a short active growing phase. The nymph softens and reshapes the apex by pushing upwards a lump of freshly mixed soaked clay, without any opening present, i. e., without ever exposing itself to the outside. We also established that the nymph is very active once its building is achieved. For example, it restores the height of the turret to its original value when shortening and opens the top of its building in case of variation of environmental parameters. Finally, we have shown how the nymph opens its edifice to reach the outside for molting into an adult stage (imago). With this work, we contributed to a better understanding of the nesting behavior of Amazon cicadas.

A CFD study on the effectiveness of trees to disperse road traffic emissions at a city scale

NASA Astrophysics Data System (ADS)

Jeanjean, A. P. R.; Hinchliffe, G.; McMullan, W. A.; Monks, P. S.; Leigh, R. J.

2015-11-01

This paper focuses on the effectiveness of trees at dispersing road traffic emissions on a city scale. CFD simulations of air-pollutant concentrations were performed using the OpenFOAM software platform using the k-ε model. Results were validated against the CODASC wind tunnel database before being applied to a LIDAR database of buildings and trees representing the City of Leicester (UK). Most other CFD models in the literature typically use idealised buildings to model wind flow and pollution dispersion. However, the methodology used in this study uses real buildings and trees data from LIDAR to reconstruct a 3D representation of Leicester City Centre. It focuses on a 2 × 2 km area which is on a scale larger than those usually used in other CFD studies. Furthermore, the primary focus of this study is on the interaction of trees with wind flow dynamics. It was found that in effect, trees have a regionally beneficial impact on road traffic emissions by increasing turbulence and reducing ambient concentrations of road traffic emissions by 7% at pedestrian height on average. This was an important result given that previous studies generally concluded that trees trapped pollution by obstructing wind flow in street canyons. Therefore, this study is novel both in its methodology and subsequent results, highlighting the importance of combining local and regional scale models for assessing the impact of trees in urban planning.

Electricity Consumption Risk Map - The use of Urban Climate Mapping for smarter analysis: Case study for Birmingham, UK.

NASA Astrophysics Data System (ADS)

Antunes Azevedo, Juliana; Burghardt, René; Chapman, Lee; Katzchner, Lutz; Muller, Catherine L.

2015-04-01

Climate is a key driving factor in energy consumption. However, income, vegetation, building mass structure, topography also impact on the amount of energy consumption. In a changing climate, increased temperatures are likely to lead to increased electricity consumption, affecting demand, distribution and generation. Furthermore, as the world population becomes more urbanized, increasing numbers of people will need to deal with not only increased temperatures from climate change, but also from the unintentional modification of the urban climate in the form of urban heat islands. Hence, climate and climate change needs to be taken into account for future urban planning aspects to increase the climate and energy resilience of the community and decrease the future social and economic costs. Geographical Information Systems provide a means to create urban climate maps as part of the urban planning process. Geostatistical analyses linking these maps with demographic and social data, enables a geo-statistical analysis to identify linkages to high-risk groups of the community and vulnerable areas of town and cities. Presently, the climatope classification is oriented towards thermal aspects and the ventilation quality (roughness) of the urban areas but can also be adapted to take into account other structural "environmental factors". This study aims to use the climatope approach to predict areas of potential high electricity consumption in Birmingham, UK. Several datasets were used to produce an average surface temperature map, vegetation map, land use map, topography map, building height map, built-up area roughness calculations, an average air temperature map and a domestic electricity consumption map. From the correlations obtained between the layers it is possible to average the importance of each factor and create a map for domestic electricity consumption to understand the influence of environmental aspects on spatial energy consumption. Based on these results city planners and local authorities can guide their directives and policies towards electricity consumption, demand, generation and distribution.

Investigating maternal risk factors as potential targets of intervention to reduce socioeconomic inequality in small for gestational age: a population-based study.

PubMed

Hayward, Irene; Malcoe, Lorraine Halinka; Cleathero, Lesley A; Janssen, Patricia A; Lanphear, Bruce P; Hayes, Michael V; Mattman, Andre; Pampalon, Robert; Venners, Scott A

2012-06-13

The major aim of this study was to investigate whether maternal risk factors associated with socioeconomic status and small for gestational age (SGA) might be viable targets of interventions to reduce differential risk of SGA by socioeconomic status (socioeconomic SGA inequality) in the metropolitan area of Vancouver, Canada. This study included 59,039 live, singleton births in the Vancouver Census Metropolitan Area (Vancouver) from January 1, 2006 to September 17, 2009. To identify an indicator of socioeconomic SGA inequality, we used hierarchical logistic regression to model SGA by area-level variables from the Canadian census. We then modelled SGA by area-level average income plus established maternal risk factors for SGA and calculated population attributable SGA risk percentages (PAR%) for each variable. Associations of maternal risk factors for SGA with average income were investigated to identify those that might contribute to SGA inequality. Finally, we estimated crude reductions in the percentage and absolute differences in SGA risks between highest and lowest average income quintiles that would result if interventions on maternal risk factors successfully equalized them across income levels or eliminated them altogether. Average income produced the most linear and statistically significant indicator of socioeconomic SGA inequality with 8.9% prevalence of SGA in the lowest income quintile compared to 5.6% in the highest. The adjusted PAR% of SGA for variables were: bottom four quintiles of height (51%), first birth (32%), bottom four quintiles of average income (14%), oligohydramnios (7%), underweight or hypertension, (6% each), smoking (3%) and placental disorder (1%). Shorter height, underweight and smoking during pregnancy had higher prevalence in lower income groups. Crude models assuming equalization of risk factors across income levels or elimination altogether indicated little potential change in relative socioeconomic SGA inequality and reduction in absolute SGA inequality for shorter height only. Our findings regarding maternal height may indicate trans-generational aetiology for socioeconomic SGA inequalities and/or that adult height influences social mobility. Conditions affecting foetal and childhood growth might be viable targets to reduce absolute socioeconomic SGA inequality in future generations, but more research is needed to determine whether such an approach is appropriate.

Making sense of the labor market height premium: Evidence from the British Household Panel Survey.

PubMed

Case, Anne; Paxson, Christina; Islam, Mahnaz

2009-03-01

We use data from the British Household Panel Survey to examine the labor market premium in height. Most of the premium is explained by higher average educational attainment and sorting into higher-status occupations and industries by those who are taller.

Wind adjustment factors for predicting fire behavior in three fuel types in Alaska.

Treesearch

Rodney A. Norum

1983-01-01

Factors for adjusting wind velocities from the 20-foot standard anemometer height down to an average wildfire midflame height (3.5 ft for the fuels studied) are given for exposed, partially sheltered, and sheltered fuels in Alaska. The values are suitable for predicting wildfire behavior.

50 CFR 216.175 - Requirements for monitoring and reporting.

Code of Federal Regulations, 2011 CFR

2011-10-01

...., FFG, DDG, or CG). (G) Length of time observers maintained visual contact with marine mammal. (H) Wave... height in feet (high, low and average during exercise). (I) Narrative description of sensors and... sensor. (F) Length of time observers maintained visual contact with marine mammal. (G) Wave height. (H...

50 CFR 218.105 - Requirements for monitoring and reporting.

Code of Federal Regulations, 2011 CFR

2011-10-01

...., FFG, DDG, or CG); (G) Length of time observers maintained visual contact with marine mammal(s); (H...., participating in exercise; (H) Wave height in feet (high, low and average during exercise); and (I) Narrative... observers maintained visual contact with marine mammal; (G) Wave height; (H) Visibility; (I) Whether...

50 CFR 218.105 - Requirements for monitoring and reporting.

Code of Federal Regulations, 2010 CFR

2010-10-01

...., FFG, DDG, or CG); (G) Length of time observers maintained visual contact with marine mammal(s); (H...., participating in exercise; (H) Wave height in feet (high, low and average during exercise); and (I) Narrative... observers maintained visual contact with marine mammal; (G) Wave height; (H) Visibility; (I) Whether...

To evaluate the validity of Recurring Esthetic Dental proportion in natural dentition

PubMed Central

Shetty, Shilpa; Pitti, Varun; Satish Babu, CL; Surendra Kumar, GP; Jnanadev, KR

2011-01-01

Background: Different proportions are described in the literature for smile designing, such as Golden proportion, Golden percentage, Preston's proportion, and recently, Recurring Esthetic Dental (RED) proportion. Aims and Objectives: To evaluate the existence of RED proportion in natural dentition. To determine the relative height of maxillary lateral incisor and canine occurring in natural dentition so that it can be used in any of the above proportions. Materials and Methods: Fifteen male subjects and 15 female subjects in each of the different age groups of 18–23 years, 24–29 years and 30–35 years were selected for this study (total 90). Photographs of the subjects were taken using Nikon D200 camera with 135 mm lens and analyzed using Adobe Photoshop CS4 extended software. The height and width of maxillary central incisors, lateral incisors and canines were found out using the measuring tool provided in the software. Results: Average width ratio and height ratio of maxillary lateral incisor to central incisor and maxillary canine to lateral incisor were calculated to check the existence of RED proportion in natural dentition. Average lateral incisor to central incisor height ratio for “small”- and “medium”-sized teeth was found to be 88% and for “tall”-sized teeth was found to be 84%. Average canine to lateral incisor height ratio for “small”- and “medium”-sized teeth was found to be 106% and for “tall”-sized teeth was found to be 105%. Conclusions: Within the limitations of the study, RED proportion was not seen in natural dentition. PMID:22025841

Thick Disks in the Hubble Space Telescope Frontier Fields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elmegreen, Bruce G.; Elmegreen, Debra Meloy; Tompkins, Brittany

Thick disk evolution is studied using edge-on galaxies in two Hubble Space Telescope Frontier Field Parallels. The galaxies were separated into 72 clumpy types and 35 spiral types with bulges. Perpendicular light profiles in F435W, F606W, and F814W ( B , V , and I ) passbands were measured at 1 pixel intervals along the major axes and fitted to sech{sup 2} functions convolved with the instrument line spread function (LSF). The LSF was determined from the average point spread function of ∼20 stars in each passband and field, convolved with a line of uniform brightness to simulate disk blurring.more » A spread function for a clumpy disk was also used for comparison. The resulting scale heights were found to be proportional to galactic mass, with the average height for a 10{sup 10±0.5} M {sub ⊙} galaxy at z = 2 ± 0.5 equal to 0.63 ± 0.24 kpc. This value is probably the result of a blend between thin and thick disk components that cannot be resolved. Evidence for such two-component structure is present in an inverse correlation between height and midplane surface brightness. Models suggest that the thick disk is observed best between the clumps, and there the average scale height is 1.06 ± 0.43 kpc for the same mass and redshift. A 0.63 ± 0.68 mag V − I color differential with height is also evidence for a mixture of thin and thick components.« less

A Biomechanical Analysis of the Effects of Bouncing the Barbell in the Conventional Deadlift.

PubMed

Krajewski, Kellen; LeFavi, Robert; Riemann, Bryan

2018-02-27

The purpose of this study is to analyze biomechanical differences between the bounce and pause styles of deadlifting. Twenty physically active males performed deadlifts at their 75% one repetition maximum testing utilizing both pause and bounce techniques in a within-subjects randomized study design. The average peak height the barbell attained from the three bounce style repetitions was used to compute a compatible phase for analysis of the pause style repetitions. Net joint moment impulse (NJMI), work, average vertical ground reaction force (vGRF), vGRF impulse and phase time were computed for two phases, lift off to peak barbell height and the entire ascent. Additionally, the ankle, knee, hip, and trunk angles at the location of peak barbell height. During the lift off to peak barbell height phase, although each of the joints demonstrated significantly less NJMI and work during the bounce style, the hip joint was impacted the most. The average vGRF was greater for the bounce however the vGRF impulse was greater for the pause. The NJMI results for the ascent phase were similar to the lift off to peak barbell height phase, while work was significantly less for the bounce condition compared to the pause condition across all three joints. Strength and conditioning specialists utilizing the deadlift should be aware that the bounce technique does not allow the athlete to develop maximal force production in the early portion of the lift. Further analyses should focus on joint angles and potential vulnerability to injury when the barbell momentum generated from the bounce is lost.

Air-Powered Rockets.

ERIC Educational Resources Information Center

Rodriguez, Charley; Raynovic, Jim

This document describes methods for designing and building two types of rockets--rockets from paper and rockets from bottles. Devices used for measuring the heights that the rockets obtain are also discussed. (KHR)

Global atmospheric circulation statistics: Four year averages

NASA Technical Reports Server (NTRS)

Wu, M. F.; Geller, M. A.; Nash, E. R.; Gelman, M. E.

1987-01-01

Four year averages of the monthly mean global structure of the general circulation of the atmosphere are presented in the form of latitude-altitude, time-altitude, and time-latitude cross sections. The numerical values are given in tables. Basic parameters utilized include daily global maps of temperature and geopotential height for 18 pressure levels between 1000 and 0.4 mb for the period December 1, 1978 through November 30, 1982 supplied by NOAA/NMC. Geopotential heights and geostrophic winds are constructed using hydrostatic and geostrophic formulae. Meridional and vertical velocities are calculated using thermodynamic and continuity equations. Fields presented in this report are zonally averaged temperature, zonal, meridional, and vertical winds, and amplitude of the planetary waves in geopotential height with zonal wave numbers 1-3. The northward fluxes of sensible heat and eastward momentum by the standing and transient eddies along with their wavenumber decomposition and Eliassen-Palm flux propagation vectors and divergences by the standing and transient eddies along with their wavenumber decomposition are also given. Large interhemispheric differences and year-to-year variations are found to originate in the changes in the planetary wave activity.

Small scale currents and ocean wave heights: from today's models to future satellite observations with CFOSAT and SKIM

NASA Astrophysics Data System (ADS)

Ardhuin, Fabrice; Gille, Sarah; Menemenlis, Dimitris; Rocha, Cesar; Rascle, Nicolas; Gula, Jonathan; Chapron, Bertrand

2017-04-01

Tidal currents and large oceanic currents, such as the Agulhas, Gulf Stream and Kuroshio, are known to modify ocean wave properties, causing extreme sea states that are a hazard to navigation. Recent advances in the understanding and modeling capability of ocean currents at scales of 10 km or less have revealed the ubiquitous presence of fronts and filaments. Based on realistic numerical models, we show that these structures can be the main source of variability in significant wave heights at scales less than 200 km, including important variations at 10 km. This current-induced variability creates gradients in wave heights that were previously overlooked and are relevant for extreme wave heights and remote sensing. The spectrum of significant wave heights is found to be of the order of 70⟨Hs ⟩2/(g2⟨Tm0,-1⟩2) times the current spectrum, where ⟨Hs ⟩ is the spatially-averaged significant wave height, ⟨Tm0,-1⟩ is the average energy period, and g is the gravity acceleration. This small scale variability is consistent with Jason-3 and SARAL along-track variability. We will discuss how future satellite mission with wave spectrometers can help observe these wave-current interactions. CFOSAT is due for launch in 2018, and SKIM is a proposal for ESA Earth Explorer 9.

Oceanographic conditions and sediment dynamic of the Barrang Caddi Island (Spermonde Archipelago, Indonesia)

NASA Astrophysics Data System (ADS)

Lanuru, M.; Samad, W.; Amri, K.; Priosambodo, D.

2018-05-01

Small islands are vulnerable to long-term natural disasters like coastal erosion due to their size and topography. Barrang Caddi is one the small island in the Spermonde Archipelago (South Sulawesi) that encountered serious coastal erosion. Several attempts have been done by the relevant parties like by building a wave breaker to prevent erosion. But in fact some parts of the island are still eroded. A comprehensive oceanographic study of the wave climate and coastal processes at work to delineate the factors responsible for shoreline chance and to identify the location that need protection is needed. In this study, physical oceanographic data including waves, currents, tide, bathymetry, sediment characteristics and sediment transport were collected in the Barrang Caddi Island to analyze the factors responsible for shoreline chance (erosion) in the island. Results of the study showed that tide in the study site is mixed tide, predominantly semidiurnal with tidal range of 118 cm. Current measurements using a electromagnetic current meter revealed that current velocities at the study site were relatively low and vary spatially and temporally with magnitude of 0.02 – 0.58 m/s. Under normal conditions (no storms) the significant wave height (H 1/3) varied from 0.04 to 0.20 m. The wave height decreases from the fore reef to the reef flat due to the presence of coral reefs that reduce wave energy (wave height). Sediments were dominated by biogenic sand with grain diameter of 0.38 – 1.04 mm. Island erosion analysis showed that wave action was a main factor that responsible for shoreline chance (erosion) at the island. Current velocity alone with average of 0.19 m/s was not strong enough to move (erode) sediments at the island.

Acid Rain

USGS Publications Warehouse

Bricker, Owen P.; Rice, Karen C.

1993-01-01

Acid deposition, or acid rain as it is more commonly referred to, has become a widely publicized environmental issue in the U.S. over the past decade. The term usually conjures up images of fish kills, dying forests, "dead" lakes, and damage to monuments and other historic artifacts. The primary cause of acid deposition is emission of S02 and NOx to the atmosphere during the combustion of fossil fuels. Oxidation of these compounds in the atmosphere forms strong acids - H2SO4 and HNO3 - which are returned to the Earth in rain, snow, fog, cloud water, and as dry deposition.Although acid deposition has only recently been recognized as an environmental problem in the U.S., it is not a new phenomenon (Cogbill & Likens 1974). As early as the middle of the 17th century in England, the deleterious effects of industrial emissions on plants, animals, and humans, and the atmospheric transport of pollutants between England and France had become issues of concern (Evelyn 1661, Graunt 1662). It is interesting that well over three hundred years ago in England, recommendations were made to move industry outside of towns and build higher chimneys to spread the pollution into "distant parts." Increasing the height of smokestacks has helped alleviate local problems, but has exacerbated others. In the U.S. the height of the tallest smokestack has more than doubled, and the average height of smokestacks has tripled since the 1950s (Patrick et al 1981). This trend occurred in most industrialized nations during the 20th century and has had the effect of transforming acid rain from a local urban problem into a problem of global scale.

Acid Rain

USGS Publications Warehouse

Bricker, Owen P.; Rice, Karen C.; Dietrich, W.E.; Sposito, Garrison

1997-01-01

Acid deposition, or acid rain as it is more commonly referred to, has become a widely publicized environmental issue in the U.S. over the past decade. The term usually conjures up images of fish kills, dying forests, "dead" lakes, and damage to monuments and other historic artifacts. The primary cause of acid deposition is emission of S02 and NOx to the atmosphere during the combustion of fossil fuels. Oxidation of these compounds in the atmosphere forms strong acids - H2SO4 and HNO3 - which are returned to the Earth in rain, snow, fog, cloud water, and as dry deposition.Although acid deposition has only recently been recognized as an environmental problem in the U.S., it is not a new phenomenon (Cogbill & Likens 1974). As early as the middle of the 17th century in England, the deleterious effects of industrial emissions on plants, animals, and humans, and the atmospheric transport of pollutants between England and France had become issues of concern (Evelyn 1661, Graunt 1662). It is interesting that well over three hundred years ago in England, recommendations were made to move industry outside of towns and build higher chimneys to spread the pollution into "distant parts." Increasing the height of smokestacks has helped alleviate local problems, but has exacerbated others. In the U.S. the height of the tallest smokestack has more than doubled, and the average height of smokestacks has tripled since the 1950s (Patrick et al 1981). This trend occurred in most industrialized nations during the 20th century and has had the effect of transforming acid rain from a local urban problem into a problem of global scale.

Effects of sea state on offshore wind resourcing in Florida

NASA Astrophysics Data System (ADS)

Collier, Cristina

Offshore resource assessment relies on estimating wind speeds at turbine hub height using observations typically made at substantially lower height. The methods used to adjust from observed wind speeds to hub height can impact resource estimation. The importance of directional sea state is examined, both as seasonal averages and as a function of the diurnal cycle. A General Electric 3.6 MW offshore turbine is used as a model for a power production. Including sea state increases or decreases seasonally averaged power production by roughly 1%, which is found to be an economically significant change. These changes occur because the sea state modifies the wind shear (vector wind difference between the buoy height and the moving surface) and therefore the extrapolation from the observation to hub height is affected. These seemingly small differences in capacity can alter profits by millions of dollars depending upon the size of the farm and fluctuations in price per kWh throughout the year. A 2% change in capacity factor can lead to a 10 million dollar difference from total kWh produced from a wind farm of 100 3.6MW turbines. These economic impacts can be a deciding factor in determining whether a resource is viable for development. Modification of power output due to sea states are shown for seasonal and diurnal time scales. Three regions are examined herein: West Florida, East Florida, and Nantucket Sound. The average capacity after sea state is included suggests areas around Florida could provide substantial amounts of wind power throughout three-fourths of the calendar year. At certain times of day winter average produced capacity factors in West Florida can be up to 45% more than in summer when sea state is included. Nantucket Sound capacity factors are calculated for comparison to a region near a planned United States offshore wind farm. This study provides evidence to suggest including sea state in offshore wind resource assessment causes economically significant differences for offshore wind power siting.

Improvement of open and semi-open core wall system in tall buildings by closing of the core section in the last story

NASA Astrophysics Data System (ADS)

Kheyroddin, A.; Abdollahzadeh, D.; Mastali, M.

2014-09-01

Increasing number of tall buildings in urban population caused development of tall building structures. One of the main lateral load resistant systems is core wall system in high-rise buildings. Core wall system has two important behavioral aspects where the first aspect is related to reduce the lateral displacement by the core bending resistance and the second is governed by increasing of the torsional resistance and core warping of buildings. In this study, the effects of closed section core in the last story have been considered on the behavior of models. Regarding this, all analyses were performed by ETABS 9.2.v software (Wilson and Habibullah). Considering (a) drift and rotation of the core over height of buildings, (b) total and warping stress in the core body, (c) shear in beams due to warping stress, (d) effect of closing last story on period of models in various modes, (e) relative displacement between walls in the core system and (f) site effects in far and near field of fault by UBC97 spectra on base shear coefficient showed that the bimoment in open core is negative in the last quarter of building and it is similar to wall-frame structures. Furthermore, analytical results revealed that closed section core in the last story improves behavior of the last quarter of structure height, since closing of core section in the last story does not have significant effect on reducing base shear value in near and far field of active faults.

Interior detail of basement door, woodenlouvered transom and glass doorknob, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior detail of basement door, wooden-louvered transom and glass doorknob, facing southeast. - Gorgas Hospital, Administration & Clinics Building, Culebra Road, Balboa Heights, Former Panama Canal Zone, CZ

Evaluation of regional and local atmospheric dispersion models for the analysis of traffic-related air pollution in urban areas

NASA Astrophysics Data System (ADS)

Fallah-Shorshani, Masoud; Shekarrizfard, Maryam; Hatzopoulou, Marianne

2017-10-01

Dispersion of road transport emissions in urban metropolitan areas is typically simulated using Gaussian models that ignore the turbulence and drag induced by buildings, which are especially relevant for areas with dense downtown cores. To consider the effect of buildings, street canyon models are used but often at the level of single urban corridors and small road networks. In this paper, we compare and validate two dispersion models with widely varying algorithms, across a modelling domain consisting of the City of Montreal, Canada accounting for emissions of more 40,000 roads. The first dispersion model is based on flow decomposition into the urban canopy sub-flow as well as overlying airflow. It takes into account the specific height and geometry of buildings along each road. The second model is a Gaussian puff dispersion model, which handles complex terrain and incorporates three-dimensional meteorology, but accounts for buildings only through variations in the initial vertical mixing coefficient. Validation against surface observations indicated that both models under-predicted measured concentrations. Average weekly exposure surfaces derived from both models were found to be reasonably correlated (r = 0.8) although the Gaussian dispersion model tended to underestimate concentrations around the roadways compared to the street canyon model. In addition, both models were used to estimate exposures of a representative sample of the Montreal population composed of 1319 individuals. Large differences were noted whereby exposures derived from the Gaussian puff model were significantly lower than exposures derived from the street canyon model, an expected result considering the concentration of population around roadways. These differences have large implications for the analyses of health effects associated with NO2 exposure.

Pacific Marine Energy Center - South Energy Test Site, Wave Measurements

DOE Data Explorer

Annette von Jouanne

2016-06-06

TRIAXYS data from the NNMREC-SETS, for Nov. 2014 - Jan. 2015, and May 2015 - Dec. 2015. The data consists of: Date, Time, significant wave height (1 hour average), significant wave period (1 hour average).

A cross-sectional study of the temporal evolution of electricity consumption of six commercial buildings.

PubMed

Pickering, Ethan M; Hossain, Mohammad A; Mousseau, Jack P; Swanson, Rachel A; French, Roger H; Abramson, Alexis R

2017-01-01

Current approaches to building efficiency diagnoses include conventional energy audit techniques that can be expensive and time consuming. In contrast, virtual energy audits of readily available 15-minute-interval building electricity consumption are being explored to provide quick, inexpensive, and useful insights into building operation characteristics. A cross sectional analysis of six buildings in two different climate zones provides methods for data cleaning, population-based building comparisons, and relationships (correlations) of weather and electricity consumption. Data cleaning methods have been developed to categorize and appropriately filter or correct anomalous data including outliers, missing data, and erroneous values (resulting in < 0.5% anomalies). The utility of a cross-sectional analysis of a sample set of building's electricity consumption is found through comparisons of baseload, daily consumption variance, and energy use intensity. Correlations of weather and electricity consumption 15-minute interval datasets show important relationships for the heating and cooling seasons using computed correlations of a Time-Specific-Averaged-Ordered Variable (exterior temperature) and corresponding averaged variables (electricity consumption)(TSAOV method). The TSAOV method is unique as it introduces time of day as a third variable while also minimizing randomness in both correlated variables through averaging. This study found that many of the pair-wise linear correlation analyses lacked strong relationships, prompting the development of the new TSAOV method to uncover the causal relationship between electricity and weather. We conclude that a combination of varied HVAC system operations, building thermal mass, plug load use, and building set point temperatures are likely responsible for the poor correlations in the prior studies, while the correlation of time-specific-averaged-ordered temperature and corresponding averaged variables method developed herein adequately accounts for these issues and enables discovery of strong linear pair-wise correlation R values. TSAOV correlations lay the foundation for a new approach to building studies, that mitigates plug load interferences and identifies more accurate insights into weather-energy relationship for all building types. Over all six buildings analyzed the TSAOV method reported very significant average correlations per building of 0.94 to 0.82 in magnitude. Our rigorous statistics-based methods applied to 15-minute-interval electricity data further enables virtual energy audits of buildings to quickly and inexpensively inform energy savings measures.

A cross-sectional study of the temporal evolution of electricity consumption of six commercial buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pickering, Ethan M.; Hossain, Mohammad A.; Mousseau, Jack P.

Current approaches to building efficiency diagnoses include conventional energy audit techniques that can be expensive and time consuming. In contrast, virtual energy audits of readily available 15-minute-interval building electricity consumption are being explored to provide quick, inexpensive, and useful insights into building operation characteristics. A cross sectional analysis of six buildings in two different climate zones provides methods for data cleaning, population-based building comparisons, and relationships (correlations) of weather and electricity consumption. Data cleaning methods have been developed to categorize and appropriately filter or correct anomalous data including outliers, missing data, and erroneous values (resulting in < 0.5% anomalies). Themore » utility of a cross-sectional analysis of a sample set of building's electricity consumption is found through comparisons of baseload, daily consumption variance, and energy use intensity. Correlations of weather and electricity consumption 15-minute interval datasets show important relationships for the heating and cooling seasons using computed correlations of a Time-Specific-Averaged- Ordered Variable (exterior temperature) and corresponding averaged variables (electricity consumption)(TSAOV method). The TSAOV method is unique as it introduces time of day as a third variable while also minimizing randomness in both correlated variables through averaging. This study found that many of the pair-wise linear correlation analyses lacked strong relationships, prompting the development of the new TSAOV method to uncover the causal relationship between electricity and weather. We conclude that a combination of varied HVAC system operations, building thermal mass, plug load use, and building set point temperatures are likely responsible for the poor correlations in the prior studies, while the correlation of time-specific-averaged-ordered temperature and corresponding averaged variables method developed herein adequately accounts for these issues and enables discovery of strong linear pair-wise correlation R values. TSAOV correlations lay the foundation for a new approach to building studies, that mitigates plug load interferences and identifies more accurate insights into weather-energy relationship for all building types. Over all six buildings analyzed the TSAOV method reported very significant average correlations per building of 0.94 to 0.82 in magnitude. Our rigorous statistics-based methods applied to 15- minute-interval electricity data further enables virtual energy audits of buildings to quickly and inexpensively inform energy savings measures.« less

A cross-sectional study of the temporal evolution of electricity consumption of six commercial buildings

DOE PAGES

Pickering, Ethan M.; Hossain, Mohammad A.; Mousseau, Jack P.; ...

2017-10-31

Current approaches to building efficiency diagnoses include conventional energy audit techniques that can be expensive and time consuming. In contrast, virtual energy audits of readily available 15-minute-interval building electricity consumption are being explored to provide quick, inexpensive, and useful insights into building operation characteristics. A cross sectional analysis of six buildings in two different climate zones provides methods for data cleaning, population-based building comparisons, and relationships (correlations) of weather and electricity consumption. Data cleaning methods have been developed to categorize and appropriately filter or correct anomalous data including outliers, missing data, and erroneous values (resulting in < 0.5% anomalies). Themore » utility of a cross-sectional analysis of a sample set of building's electricity consumption is found through comparisons of baseload, daily consumption variance, and energy use intensity. Correlations of weather and electricity consumption 15-minute interval datasets show important relationships for the heating and cooling seasons using computed correlations of a Time-Specific-Averaged- Ordered Variable (exterior temperature) and corresponding averaged variables (electricity consumption)(TSAOV method). The TSAOV method is unique as it introduces time of day as a third variable while also minimizing randomness in both correlated variables through averaging. This study found that many of the pair-wise linear correlation analyses lacked strong relationships, prompting the development of the new TSAOV method to uncover the causal relationship between electricity and weather. We conclude that a combination of varied HVAC system operations, building thermal mass, plug load use, and building set point temperatures are likely responsible for the poor correlations in the prior studies, while the correlation of time-specific-averaged-ordered temperature and corresponding averaged variables method developed herein adequately accounts for these issues and enables discovery of strong linear pair-wise correlation R values. TSAOV correlations lay the foundation for a new approach to building studies, that mitigates plug load interferences and identifies more accurate insights into weather-energy relationship for all building types. Over all six buildings analyzed the TSAOV method reported very significant average correlations per building of 0.94 to 0.82 in magnitude. Our rigorous statistics-based methods applied to 15- minute-interval electricity data further enables virtual energy audits of buildings to quickly and inexpensively inform energy savings measures.« less

Radon in indoor concentrations and indoor concentrations of metal dust particles in museums and other public buildings.

PubMed

Carneiro, G L; Braz, D; de Jesus, E F; Santos, S M; Cardoso, K; Hecht, A A; Dias da Cunha, Moore K

2013-06-01

The aim of this study was to evaluate the public and occupational exposure to radon and metal-bearing particles in museums and public buildings located in the city of Rio de Janeiro, Brazil. For this study, four buildings were selected: two historic buildings, which currently house an art gallery and an art museum; and two modern buildings, a chapel and a club. Integrated radon concentration measurements were performed using passive radon detectors with solid state nuclear track detector-type Lexan used as nuclear track detector. Air samplers with a cyclone were used to collect the airborne particle samples that were analyzed by the particle-induced X-ray emission technique. The average unattached-radon concentrations in indoor air in the buildings were above 40 Bq/m(3), with the exception of Building D as measured in 2009. The average radon concentrations in indoor air in the four buildings in 2009 were below the recommended reference level by World Health Organization (100 Bq/m(3)); however, in 2011, the average concentrations of radon in Buildings A and C were above this level, though lower than 300 Bq/m(3). The average concentrations of unattached radon were lower than 148 Bq/m(3) (4pCi/L), the USEPA level recommended to take action to reduce the concentrations of radon in indoor air. The unattached-radon average concentrations were also lower than the value recommended by the European Union for new houses. As the unattached-radon concentrations were below the international level recommended to take action to reduce the radon concentration in air, it was concluded that during the period of sampling, there was low risk to human health due to the inhalation of unattached radon in these four buildings.

Mechanical behavior of post-processed Inconel 718 manufactured through the electron beam melting process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirka, Michael M.; Medina, Frank; Dehoff, Ryan R.

Here, the electron beam melting (EBM) process was used to fabricate Inconel 718. The microstructure and tensile properties were characterized in both the as-fabricated and post-processed state transverse (T-orientation) and longitudinal (L-orientation) to the build direction. Post-processing involved both a hot isostatic pressing (HIP) and solution treatment and aging (STA) to homogenize the microstructure. In the as-fabricated state, EBM Inconel 718 exhibits a spatially dependent microstructure that is a function of build height. Spanning the last few layers is a cored dendritic structure comprised of the products (carbides and Laves phase) predicted under equilibrium solidification conditions. With increasing distance frommore » the build's top surface, the cored dendritic structure becomes increasingly homogeneous with complete dissolution of the secondary dendrite arms. Further, temporal phase kinetics are observed to lead to the dissolution of the strengthening γ"γ" and precipitation of networks of fine δ needles that span the grains. Microstructurally, post-processing resulted in dissolution of the δ networks and homogeneous precipitation of γ'"γ'" throughout the height of the build. In the as-fabricated state, the monotonic tensile behavior exhibits a height sensitivity within the T-orientation at both 20 and 650 °C. Along the L-orientation, the tensile behavior exhibits strength values comparable to the reference wrought material in the fully heat-treated state. After post-processing, the yield strength, ultimate strength, and elongation at failure for the EBM Inconel 718 were observed to have beneficially increased compared to the as-fabricated material. Further, as a result of post-processing the spatial variance of the ultimate yield strength and elongation at failure within the transverse direction decreased by 4 and 3× respectively.« less

Mechanical behavior of post-processed Inconel 718 manufactured through the electron beam melting process

DOE PAGES

Kirka, Michael M.; Medina, Frank; Dehoff, Ryan R.; ...

2016-10-21

Here, the electron beam melting (EBM) process was used to fabricate Inconel 718. The microstructure and tensile properties were characterized in both the as-fabricated and post-processed state transverse (T-orientation) and longitudinal (L-orientation) to the build direction. Post-processing involved both a hot isostatic pressing (HIP) and solution treatment and aging (STA) to homogenize the microstructure. In the as-fabricated state, EBM Inconel 718 exhibits a spatially dependent microstructure that is a function of build height. Spanning the last few layers is a cored dendritic structure comprised of the products (carbides and Laves phase) predicted under equilibrium solidification conditions. With increasing distance frommore » the build's top surface, the cored dendritic structure becomes increasingly homogeneous with complete dissolution of the secondary dendrite arms. Further, temporal phase kinetics are observed to lead to the dissolution of the strengthening γ"γ" and precipitation of networks of fine δ needles that span the grains. Microstructurally, post-processing resulted in dissolution of the δ networks and homogeneous precipitation of γ'"γ'" throughout the height of the build. In the as-fabricated state, the monotonic tensile behavior exhibits a height sensitivity within the T-orientation at both 20 and 650 °C. Along the L-orientation, the tensile behavior exhibits strength values comparable to the reference wrought material in the fully heat-treated state. After post-processing, the yield strength, ultimate strength, and elongation at failure for the EBM Inconel 718 were observed to have beneficially increased compared to the as-fabricated material. Further, as a result of post-processing the spatial variance of the ultimate yield strength and elongation at failure within the transverse direction decreased by 4 and 3× respectively.« less

Size and site dependent biological hazard potential of particulate matters collected from different heights at the vicinity of a building construction.

PubMed

Li, Huaqiong; Fang, Crystal Hay Yu; Shi, Wenxiong; Gurusamy, Subramaniam; Li, Shuzhou; Krishnan, Manoj N; George, Saji

2015-11-04

Although building constructions are a recurring part of urbanization, the health risk of particulate matters (PM) originating from such activities have seldom been subjected to detailed studies. We sought to characterize the relative risk of air borne PM collected from different heights (ground and top floor) of a building adjacent to a building under early phase of construction. We determined the physico-chemical properties such as size and shape, elemental composition and surface charge of the PM. The oxidative stress dependent cytotoxic and pro-inflammatory responses were assessed in BEAS-2B and RAW 264.7 cell lines using high-content-screening platforms. In comparison to top floor, the total mass of PM collected from ground floor was two-three folds higher and the mass fraction was dominated by PM20-35. Elemental analysis showed abundance of Si, Al, K, Ca and Fe in bigger PM while for PM0.25-0.5 it was mostly constituted by C and crystals rich in S and K. PM caused NFκB activation, secretion of pro-inflammatory cytokines and cytotoxicity wherein PM0.25-0.5 was the most potent among the tested PM. Estimated exposure level and lung burden together with the data on hazard potential were used for developing a MATLAB based risk-assessment model which suggested that the potential for health risk is relatively higher at the ground floor. Our studies demonstrated differences in, relative abundance of PM, their physicochemical and biological properties collected from different heights adjacent to a construction site and showed that relative health risk is higher at the ground floor. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Base Reutilization Status: An Assessment

DTIC Science & Technology

2000-03-01

substantially as office build- ings and retail buildings are constructed. No data are available on payrolls for the new jobs . However, earnings are likely to...date is 30.3 The average earnings from the new jobs are above the state average. The average earnings from the existing number of biotechnology

Three centuries of multi-storied St. Petersburg

NASA Astrophysics Data System (ADS)

Lavrov, Leonid; Perov, Fedor; Eremeeva, Aleksandra; Temnov, Vladimir

2018-03-01

The article is devoted to assessment of the role of high-rise buildings in the St. Petersburg historic city's ensemble. Features of formation of city architectural look, the conditions of city typical silhouette's appearance which is characterized by the contrast of a small number of high-rise structures with a low horizontal mass building are observed. The consequences of the emergence of a significant number of great height buildings, the silhouette of which conflicts with the traditional St. Petersburg landscape's compositional principles, are analyzed. The economic reasons of high-rise construction of residential and office buildings are given. The conclusions about the prospects of St. Petersburg high-rise construction in the light of city-building and economic factors are made.

Statistical trend analysis and extreme distribution of significant wave height from 1958 to 1999 - an application to the Italian Seas

NASA Astrophysics Data System (ADS)

Martucci, G.; Carniel, S.; Chiggiato, J.; Sclavo, M.; Lionello, P.; Galati, M. B.

2010-06-01

The study is a statistical analysis of sea states timeseries derived using the wave model WAM forced by the ERA-40 dataset in selected areas near the Italian coasts. For the period 1 January 1958 to 31 December 1999 the analysis yields: (i) the existence of a negative trend in the annual- and winter-averaged sea state heights; (ii) the existence of a turning-point in late 80's in the annual-averaged trend of sea state heights at a site in the Northern Adriatic Sea; (iii) the overall absence of a significant trend in the annual-averaged mean durations of sea states over thresholds; (iv) the assessment of the extreme values on a time-scale of thousand years. The analysis uses two methods to obtain samples of extremes from the independent sea states: the r-largest annual maxima and the peak-over-threshold. The two methods show statistical differences in retrieving the return values and more generally in describing the significant wave field. The r-largest annual maxima method provides more reliable predictions of the extreme values especially for small return periods (<100 years). Finally, the study statistically proves the existence of decadal negative trends in the significant wave heights and by this it conveys useful information on the wave climatology of the Italian seas during the second half of the 20th century.

Unmanned aircraft system-derived crop height and normalized difference vegetation index metrics for sorghum yield and aphid stress assessment

NASA Astrophysics Data System (ADS)

Stanton, Carly; Starek, Michael J.; Elliott, Norman; Brewer, Michael; Maeda, Murilo M.; Chu, Tianxing

2017-04-01

A small, fixed-wing unmanned aircraft system (UAS) was used to survey a replicated small plot field experiment designed to estimate sorghum damage caused by an invasive aphid. Plant stress varied among 40 plots through manipulation of aphid densities. Equipped with a consumer-grade near-infrared camera, the UAS was flown on a recurring basis over the growing season. The raw imagery was processed using structure-from-motion to generate normalized difference vegetation index (NDVI) maps of the fields and three-dimensional point clouds. NDVI and plant height metrics were averaged on a per plot basis and evaluated for their ability to identify aphid-induced plant stress. Experimental soil signal filtering was performed on both metrics, and a method filtering low near-infrared values before NDVI calculation was found to be the most effective. UAS NDVI was compared with NDVI from sensors onboard a manned aircraft and a tractor. The correlation results showed dependence on the growth stage. Plot averages of NDVI and canopy height values were compared with per-plot yield at 14% moisture and aphid density. The UAS measures of plant height and NDVI were correlated to plot averages of yield and insect density. Negative correlations between aphid density and NDVI were seen near the end of the season in the most damaged crops.

Crestal sinus lift with sequential drills and simultaneous implant placement in sites with <5 mm of native bone: a multicenter retrospective study.

PubMed

Bernardello, Fabio; Righi, Davide; Cosci, Ferdinando; Bozzoli, Paolo; Soardi, Carlo Maria; Carlo, Maria Soardi; Spinato, Sergio

2011-12-01

The aim of this multicenter retrospective clinical study was to evaluate the survival rate of implants placed in the posterior maxilla with a residual bone height of <5 mm. One hundred seventeen patients, recruited from 6 different centers, had 134 implants placed below the maxillary sinus. The patient population consisted of 52 men and 65 women ranging in age from 39 to 78 years (mean age, 53.2 years). Sinus lift procedures were performed following a crestal approach using a specific sequence of drills (Cosci's technique). All implants were submerged. Periapical radiographs were obtained with a paralleling technique and were digitized. The pattern of bone remodeling was subsequently evaluated. The average (±SD) follow-up time was 48.2 months (±29.30 months; range, 24 to 120 months). Of the original 134 implants placed, 5 implants (3.7%) failed. The implant survival rate was 96.3%. The average residual bone height was 3.46 mm (±0.91 mm) at baseline. The average height of the alveolar crest in the treated implant sites was 9.94 ± 2.29 mm. The radiographic bone gain was 6.48 ± 2.38 mm. The investigation suggests that this crestal drill approach can be a successful sinus lifting procedure in a severe atrophic maxilla with <5 mm of crestal bone height.

Effects of Long-Term Low-Level Radiofrequency Radiation Exposure on Rats. Volume 2. Average SAR and SAR Distribution in Man Exposed to 450-MHz RFR.

DTIC Science & Technology

1983-09-01

adult man (full-scale height = 171 cm) and child (full-scale height = 86 cm), with arms down. We used the full-scale figure to reflect a worst-case... child for all orientations was much higher than that for the adult (e.g., 0.187 W/kg versus 0.063 W/kg), which is expected since the frequency is closer...to the resonance frequency for the child . Another series of scale-model measurements was conducted for determination of the average SAR values for

5. INTERIOR VIEW SHOWING RAFTER CONSTRUCTION. SOUTHERN EXTENSION AT LEFT. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. INTERIOR VIEW SHOWING RAFTER CONSTRUCTION. SOUTHERN EXTENSION AT LEFT. - Chollas Heights Naval Radio Transmitting Facility, Operational Storage Building, 6410 Zero Road, San Diego, San Diego County, CA

ARC-1969-AC-42137

NASA Image and Video Library

1969-02-05

Height-Control Test Apparatus (HICONTA) Simulator mounted to the exterior of the 40x80ft W.T. Building N-221B and provided extensive vertical motion simulating airplanes, helicopter and V/STOL aircraft

Earthquake insurance pricing: a risk-based approach.

PubMed

Lin, Jeng-Hsiang

2018-04-01

Flat earthquake premiums are 'uniformly' set for a variety of buildings in many countries, neglecting the fact that the risk of damage to buildings by earthquakes is based on a wide range of factors. How these factors influence the insurance premiums is worth being studied further. Proposed herein is a risk-based approach to estimate the earthquake insurance rates of buildings. Examples of application of the approach to buildings located in Taipei city of Taiwan were examined. Then, the earthquake insurance rates for the buildings investigated were calculated and tabulated. To fulfil insurance rating, the buildings were classified into 15 model building types according to their construction materials and building height. Seismic design levels were also considered in insurance rating in response to the effect of seismic zone and construction years of buildings. This paper may be of interest to insurers, actuaries, and private and public sectors of insurance. © 2018 The Author(s). Disasters © Overseas Development Institute, 2018.

Fertilization and spacing effects on growth of planted ponderosa pine.

Treesearch

P.H. Cochran; R.P. Newman; James W. Barrett

1991-01-01

Fertilizer placed in the planting hole increased height growth of ponderosa pine (Pinus ponderosa Dougl. ex Laws.) early in the life of the plantation. Later broadcast applications of fertilizer may have had little effect on growth. Wider spacings produced larger trees but less volume per acre than narrower spacings after average tree height...

Towards an anthropometric history of latin America in the second half of the twentieth century.

PubMed

Challú, Amílcar E; Silva-Castañeda, Sergio

2016-12-01

We examine the evolution of adult female heights in twelve Latin American countries during the second half of the twentieth century based on demographic health surveys and related surveys compiled from national and international organizations. Only countries with more than one survey were included, allowing us to cross-examine surveys and correct for biases. We first show that average height varies significantly according to location, from 148.3cm in Guatemala to 158.8cm in Haiti. The evolution of heights over these decades behaves like indicators of human development, showing a steady increase of 2.6cm from the 1950s to the 1990s. Such gains compare favorably to other developing regions of the world, but not so much with recently developed countries. Height gains were not evenly distributed in the region, however. Countries that achieved higher levels of income, such as Brazil, Chile, Colombia and Mexico, gained on average 0.9cm per decade, while countries with shrinking economies, such as Haiti and Guatemala, only gained 0.25cm per decade. Copyright © 2016 Elsevier B.V. All rights reserved.

Orthodontic Bracket Manufacturing Tolerances and Dimensional Differences between Select Self-Ligating Brackets

PubMed Central

Major, Thomas W.; Carey, Jason P.; Nobes, David S.; Major, Paul W.

2010-01-01

In all manufacturing processes there are tolerances; however, orthodontic bracket manufacturers seldom state the slot dimensional tolerances. This experiment develops a novel method of analyzing slot profile dimensions using photographs of the slot. Five points are selected along each wall, and lines are fitted to define a trapezoidal slot shape. This investigation measures slot height at the slot's top and bottom, angles between walls, slot taper, and the linearity of each wall. Slot dimensions for 30 upper right central incisor self-ligating stainless steel brackets from three manufacturers were evaluated. Speed brackets have a slot height 2% smaller than the nominal 0.559 mm size and have a slightly convergent taper. In-Ovation brackets have a divergent taper at an average angle of 1.47 degrees. In-Ovation is closest to the nominal value of slot height at the slot base and has the smallest manufacturing tolerances. Damon Q brackets are the most rectangular in shape, with nearly 90-degree corners between the slot bottom and walls. Damon slot height is on average 3% oversized. PMID:20981299

A cross-sectional study of the temporal evolution of electricity consumption of six commercial buildings

PubMed Central

Hossain, Mohammad A.; Mousseau, Jack P.; Swanson, Rachel A.; French, Roger H.; Abramson, Alexis R.

2017-01-01

Current approaches to building efficiency diagnoses include conventional energy audit techniques that can be expensive and time consuming. In contrast, virtual energy audits of readily available 15-minute-interval building electricity consumption are being explored to provide quick, inexpensive, and useful insights into building operation characteristics. A cross sectional analysis of six buildings in two different climate zones provides methods for data cleaning, population-based building comparisons, and relationships (correlations) of weather and electricity consumption. Data cleaning methods have been developed to categorize and appropriately filter or correct anomalous data including outliers, missing data, and erroneous values (resulting in < 0.5% anomalies). The utility of a cross-sectional analysis of a sample set of building’s electricity consumption is found through comparisons of baseload, daily consumption variance, and energy use intensity. Correlations of weather and electricity consumption 15-minute interval datasets show important relationships for the heating and cooling seasons using computed correlations of a Time-Specific-Averaged-Ordered Variable (exterior temperature) and corresponding averaged variables (electricity consumption)(TSAOV method). The TSAOV method is unique as it introduces time of day as a third variable while also minimizing randomness in both correlated variables through averaging. This study found that many of the pair-wise linear correlation analyses lacked strong relationships, prompting the development of the new TSAOV method to uncover the causal relationship between electricity and weather. We conclude that a combination of varied HVAC system operations, building thermal mass, plug load use, and building set point temperatures are likely responsible for the poor correlations in the prior studies, while the correlation of time-specific-averaged-ordered temperature and corresponding averaged variables method developed herein adequately accounts for these issues and enables discovery of strong linear pair-wise correlation R values. TSAOV correlations lay the foundation for a new approach to building studies, that mitigates plug load interferences and identifies more accurate insights into weather-energy relationship for all building types. Over all six buildings analyzed the TSAOV method reported very significant average correlations per building of 0.94 to 0.82 in magnitude. Our rigorous statistics-based methods applied to 15-minute-interval electricity data further enables virtual energy audits of buildings to quickly and inexpensively inform energy savings measures. PMID:29088269

Bilateral contact ground reaction forces and contact times during plyometric drop jumping.

PubMed

Ball, Nick B; Stock, Christopher G; Scurr, Joanna C

2010-10-01

Drop jumping (DJ) is used in training programs aimed to improve lower extremity explosive power. When performing double-leg drop jumps, it is important to provide an equal stimulus to both legs to ensure balanced development of the lower legs. The aim of this study was to bilaterally analyze the ground reactions forces and temporal components of drop jumping from 3 heights. Ten recreationally active male subjects completed 3 bounce-drop jumps from 3 starting heights (0.2, 0.4, and 0.6 m). Two linked force platforms were used to record left- and right-leg peak vertical force, time to peak force, average force, ground contact time, impulse and time differential. Between-height and between-leg comparisons for each variable were made using a multivariate analysis of variance with post hoc Wilcoxon tests (p < 0.05). Results indicated that force and time variables increased as drop jump height increased (p < 0.0001). Post hoc analyses showed that at 0.2- and 0.4-m bilateral differences were present in the time to peak force, average force, and impulse. No bilateral differences for any variables were shown at 0.6-m starting height. The contact time for all jumps was <0.26 seconds. At 0.2 m, only 63% of the subjects had a starting time differential of <0.01 seconds, rising to 96.3% at 0.6 m. The results indicated that 0.6 m is the suggested drop jump height to ensure that no bilateral differences in vertical forces and temporal components occur; however, shorter contact times were found at the lower heights.

Forest Resource Measurements by Combination of Terrestrial Laser Scanning and Drone Use

NASA Astrophysics Data System (ADS)

Cheung, K.; Katoh, M.; Horisawa, M.

2017-10-01

Using terrestrial laser scanning (TLS), forest attributes such as diameter at breast height (DBH) and tree location can be measured accurately. However, due to low penetration of laser pulses to tree tops, tree height measurements are typically underestimated. In this study, data acquired by TLS and drones were combined; DBH and tree locations were determined by TLS, and tree heights were measured by drone use. The average tree height error and root mean square error (RMSE) of tree height were 0.8 and 1.2 m, respectively, for the combined method, and -0.4 and 1.7 m using TLS alone. The tree height difference was compared using airborne laser scanning (ALS). Furthermore, a method to acquire 100 % tree detection rate based on TLS data is suggested in this study.

The relationship of Polish students' height, weight and BMI with some socioeconomic variables.

PubMed

Krzyzanowska, Monika; Umławska, Wioleta

2010-09-01

The aim of this study was to assess the variation in student body height, weight and BMI in relation to several socioeconomic factors. Data (collected in 1998) were obtained through a structured questionnaire from 2800 students (1023 men and 1777 women) from Wrocław Universities, Poland. Information on students' age, reported height and weight and their place of residence prior to starting university, the number of siblings and parents' education were collected. Students with mothers or fathers with higher education had, on average, higher mean heights, but after correcting for other socioeconomic variables only place of residence showed a significant association with height and BMI, with those living in medium or large urban centres having a higher mean height and those living in small or medium urban areas having a lower mean BMI.

Research on ionospheric tomography based on variable pixel height

NASA Astrophysics Data System (ADS)

Zheng, Dunyong; Li, Peiqing; He, Jie; Hu, Wusheng; Li, Chaokui

2016-05-01

A novel ionospheric tomography technique based on variable pixel height was developed for the tomographic reconstruction of the ionospheric electron density distribution. The method considers the height of each pixel as an unknown variable, which is retrieved during the inversion process together with the electron density values. In contrast to conventional computerized ionospheric tomography (CIT), which parameterizes the model with a fixed pixel height, the variable-pixel-height computerized ionospheric tomography (VHCIT) model applies a disturbance to the height of each pixel. In comparison with conventional CIT models, the VHCIT technique achieved superior results in a numerical simulation. A careful validation of the reliability and superiority of VHCIT was performed. According to the results of the statistical analysis of the average root mean square errors, the proposed model offers an improvement by 15% compared with conventional CIT models.

The Influence of Changes in Size and Proportion of Selected Facial Features (Eyes, Nose, Mouth) on Assessment of Similarity between Female Faces.

PubMed

Lewandowski, Zdzisław

2015-09-01

The project aimed at finding the answers to the following two questions: to what extent does a change in size, height or width of the selected facial features influence the assessment of likeness between an original female composite portrait and a modified one? And how does the sex of the person who judges the images have an impact on the perception of likeness of facial features? The first stage of the project consisted of creating the image of the averaged female faces. Then the basic facial features like eyes, nose and mouth were cut out of the averaged face and each of these features was transformed in three ways: its size was changed by reduction or enlargement, its height was modified through reduction or enlargement of the above-mentioned features and its width was altered through widening or narrowing. In each out of six feature alternation methods, intensity of modification reached up to 20% of the original size with changes every 2%. The features altered in such a way were again stuck onto the original faces and retouched. The third stage consisted of the assessment, performed by the judges of both sexes, of the extent of likeness between the averaged composite portrait (without any changes) and the modified portraits. The results indicate that there are significant differences in the assessment of likeness of the portraits with some features modified to the original ones. The images with changes in the size and height of the nose received the lowest scores on the likeness scale, which indicates that these changes were perceived by the subjects as the most important. The photos with changes in the height of lip vermillion thickness (the lip height), lip width and the height and width of eye slit, in turn, received high scores of likeness, in spite of big changes, which signifies that these modifications were perceived as less important when compared to the other features investigated.

A review of US anthropometric reference data (1971 2000) with comparisons to both stylized and tomographic anatomic models

NASA Astrophysics Data System (ADS)

Huh, C.; Bolch, W. E.

2003-10-01

Two classes of anatomic models currently exist for use in both radiation protection and radiation dose reconstruction: stylized mathematical models and tomographic voxel models. The former utilize 3D surface equations to represent internal organ structure and external body shape, while the latter are based on segmented CT or MR images of a single individual. While tomographic models are clearly more anthropomorphic than stylized models, a given model's characterization as being anthropometric is dependent upon the reference human to which the model is compared. In the present study, data on total body mass, standing/sitting heights and body mass index are collected and reviewed for the US population covering the time interval from 1971 to 2000. These same anthropometric parameters are then assembled for the ORNL series of stylized models, the GSF series of tomographic models (Golem, Helga, Donna, etc), the adult male Zubal tomographic model and the UF newborn tomographic model. The stylized ORNL models of the adult male and female are found to be fairly representative of present-day average US males and females, respectively, in terms of both standing and sitting heights for ages between 20 and 60-80 years. While the ORNL adult male model provides a reasonably close match to the total body mass of the average US 21-year-old male (within ~5%), present-day 40-year-old males have an average total body mass that is ~16% higher. For radiation protection purposes, the use of the larger 73.7 kg adult ORNL stylized hermaphrodite model provides a much closer representation of average present-day US females at ages ranging from 20 to 70 years. In terms of the adult tomographic models from the GSF series, only Donna (40-year-old F) closely matches her age-matched US counterpart in terms of average body mass. Regarding standing heights, the better matches to US age-correlated averages belong to Irene (32-year-old F) for the females and Golem (38-year-old M) for the males. Both Helga (27-year-old F) and Donna, however, provide good matches to average US sitting heights for adult females, while Golem and Otoko (male of unknown age) yield sitting heights that are slightly below US adult male averages. Finally, Helga is seen as the only GSF tomographic female model that yields a body mass index in line with her average US female counterpart at age 26. In terms of dose reconstruction activities, however, all current tomographic voxel models are valuable assets in attempting to cover the broad distribution of individual anthropometric parameters representative of the current US population. It is highly recommended that similar attempts to create a broad library of tomographic models be initiated in the United States and elsewhere to complement and extend the limited number of tomographic models presently available for these efforts.

Men's facial masculinity: when (body) size matters.

PubMed

Holzleitner, Iris J; Hunter, David W; Tiddeman, Bernard P; Seck, Alassane; Re, Daniel E; Perrett, David I

2014-01-01

Recent studies suggest that judgments of facial masculinity reflect more than sexually dimorphic shape. Here, we investigated whether the perception of masculinity is influenced by facial cues to body height and weight. We used the average differences in three-dimensional face shape of forty men and forty women to compute a morphological masculinity score, and derived analogous measures for facial correlates of height and weight based on the average face shape of short and tall, and light and heavy men. We found that facial cues to body height and weight had substantial and independent effects on the perception of masculinity. Our findings suggest that men are perceived as more masculine if they appear taller and heavier, independent of how much their face shape differs from women's. We describe a simple method to quantify how body traits are reflected in the face and to define the physical basis of psychological attributions.

14. FACILITY IDENTIFICATION STENCILED ON ROOF BEAM, 'RIGGING LOFT' PORTION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. FACILITY IDENTIFICATION STENCILED ON ROOF BEAM, 'RIGGING LOFT' PORTION OF BUILDING 4. - Chollas Heights Naval Radio Transmitting Facility, Public Works Shop, 6410 Zero Road, San Diego, San Diego County, CA

24. INTERIOR OF CENTRAL ROOM. BASE POWER PANEL VISIBLE ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. INTERIOR OF CENTRAL ROOM. BASE POWER PANEL VISIBLE ON RIGHT WALL OF HALLWAY. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

20. INTERIOR OF SOUTHERN ROOM. VIEW LOOKING NORTHWEST TOWARD HALL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. INTERIOR OF SOUTHERN ROOM. VIEW LOOKING NORTHWEST TOWARD HALL CONNECTING WITH CENTRAL ROOM. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

6. VIEW SHOWING DETAILS OF ENCLOSED FRONT PORCH ON NORTHWEST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. VIEW SHOWING DETAILS OF ENCLOSED FRONT PORCH ON NORTHWEST CORNER OF BUILDING. - Chollas Heights Naval Radio Transmitting Facility, Officer's Quarters, 6410 Zero Road, San Diego, San Diego County, CA

Storm surges and coastal impacts at Mar del Plata, Argentina

NASA Astrophysics Data System (ADS)

Fiore, Mónica M. E.; D'Onofrio, Enrique E.; Pousa, Jorge L.; Schnack, Enrique J.; Bértola, Germán R.

2009-07-01

Positive storm surges (PSS) lasting for several days can raise the water level producing significant differences between the observed level and the astronomical tide. These storm events can be more severe if they coincide with a high tide or if they bracket several tidal cycles, particularly in the case of the highest astronomical tide. Besides, the abnormal sea-level elevation near the coast can cause the highest waves generated to attack the upper beach. This combination of factors can produce severe erosion, threatening sectors located along the coastline. These effects would be more serious if the storm surge height and duration increase as a result of a climatic change. The Mar del Plata (Argentina) coastline and adjacent areas are exposed to such effects. A statistical characterization of PSS based on their intensity, duration and frequency, including a surge event classification, was performed utilizing tide-gauge records over the period 1956-2005. A storm erosion potential index (SEPI) was calculated from observed levels based on hourly water level measurements. The index was related to beach profile responses to storm events. Also, a return period for extreme SEPI values was calculated. Results show an increase in the average number of positive storm surge events per decade. Considering all the events, the last decade (1996-2005) exhibits an average 7% increase compared to each one of the previous decades. A similar behavior was found for the decadal average of the heights of maximum annual positive storm surges. In this case the average height of the last two decades exceeds that of the previous decades by approximately 8 cm. The decadal average of maximum annual duration of these meteorological events shows an increase of 2 h in the last three decades. A possible explanation of the changes in frequency, height and duration of positive storm surges at Mar del Plata would seem to lie in the relative mean sea-level rise.

Biomechanics of Thoracolumbar Burst and Chance-Type Fractures during Fall from Height

PubMed Central

Ivancic, Paul C.

2014-01-01

Study Design In vitro biomechanical study. Objective To investigate the biomechanics of thoracolumbar burst and Chance-type fractures during fall from height. Methods Our model consisted of a three-vertebra human thoracolumbar specimen (n = 4) stabilized with muscle force replication and mounted within an impact dummy. Each specimen was subjected to a single fall from an average height of 2.1 m with average velocity at impact of 6.4 m/s. Biomechanical responses were determined using impact load data combined with high-speed movie analyses. Injuries to the middle vertebra of each spinal segment were evaluated using imaging and dissection. Results Average peak compressive forces occurred within 10 milliseconds of impact and reached 40.3 kN at the ground, 7.1 kN at the lower vertebra, and 3.6 kN at the upper vertebra. Subsequently, average peak flexion (55.0 degrees) and tensile forces (0.7 kN upper vertebra, 0.3 kN lower vertebra) occurred between 43.0 and 60.0 milliseconds. The middle vertebra of all specimens sustained pedicle and endplate fractures with comminution, bursting, and reduced height of its vertebral body. Chance-type fractures were observed consisting of a horizontal split fracture through the laminae and pedicles extending anteriorly through the vertebral body. Conclusions We hypothesize that the compression fractures of the pedicles and vertebral body together with burst fracture occurred at the time of peak spinal compression, 10 milliseconds. Subsequently, the onset of Chance-type fracture occurred at 20 milliseconds through the already fractured and weakened pedicles and vertebral body due to flexion-distraction and a forward shifting spinal axis of rotation. PMID:25083357

Urban Morphology Influence on Urban Albedo: A Revisit with the S olene Model

NASA Astrophysics Data System (ADS)

Groleau, Dominique; Mestayer, Patrice G.

2013-05-01

This heuristic study of the urban morphology influence on urban albedo is based on some 3,500 simulations with the S olene model. The studied configurations include square blocks in regular and staggered rows, rectangular blocks with different street widths, cross-shaped blocks, infinite street canyons and several actual districts in Marseilles, Toulouse and Nantes, France. The scanned variables are plan density, facade density, building height, layout orientation, latitude, date and time of the day. The sky-view factors of the ground and canopy surfaces are also considered. This study demonstrates the significance of the facade density, in addition to the built plan density, as the explanatory geometrical factor to characterize the urban morphology, rather than building height. On the basis of these albedo calculations the puzzling results of Kondo et al. (Boundary-Layer Meteorol 100:225-242, 2001) for the influence of building height are explained, and the plan density influence is quantitatively assessed. It is shown that the albedo relationship with plan and facade densities obtained with the regular square plot configuration may be considered as a reference for all other configurations, with the exception of the infinite street canyon that shows systematic differences for the lower plan densities. The curves representing this empirical relationship may be used as a sort of abacus for all other geometries while an approximate simple mathematical model is proposed, as well as relationships between the albedo and sky-view factors.

Influence of urban morphology on total noise pollution: multifractal description.

PubMed

Ariza-Villaverde, Ana B; Jiménez-Hornero, Francisco J; Gutiérrez De Ravé, Eduardo

2014-02-15

Exposure to ambient noise levels above 65 dB can cause public health problems. The spatial distribution of this kind of pollution is linked to various elements which make up the urban form, such as construction density, the existence of open spaces and the shape and physical position of buildings. Since urban morphology displays multifractal behaviour, the present research studies for the first time the relationship between total noise pollution and urban features, such as street width and building height by means of a joint multifractal spectrum in two neighbourhoods of the city of Cordoba (Andalusia, Spain). According to the results, the joint multifractal spectrum reveals a positive correlation between the total noise pollution and the street width to building height ratio, this being more evident when urban morphology is regular. The information provided by the multifractal analysis completes the description obtained by using urban indexes and landscape metrics and might be useful for urban planning once the linkage between both frameworks has been done. Copyright © 2013 Elsevier B.V. All rights reserved.

On the corrosion and soiling effects on materials by air pollution in Athens, Greece

NASA Astrophysics Data System (ADS)

Tzanis, C.; Varotsos, C.; Christodoulakis, J.; Tidblad, J.; Ferm, M.; Ionescu, A.; Lefevre, R.-A.; Theodorakopoulou, K.; Kreislova, K.

2011-12-01

In the frame of the European project, entitled MULTI-ASSESS, specimens of structural metals, glass, stone and concrete materials were exposed to air pollution at a station, which was installed for this purpose on a building, located in the centre of Athens. The main purpose of this project was to determine the corrosion and soiling effects of air pollution on materials. A set of the specimens was exposed in a position that was sheltered from rain and partly from wind, and another set was exposed in unsheltered positions on the roof of the above said building. In addition, other specimens were exposed at different heights on the same building, in order to investigate for the first time the corrosion and soiling effects on various materials as a function of height. For the determination of these effects, chemical analysis of the specimens was performed and basic parameters as the weight change, the layer thickness and the optical properties were calculated. Finally, the results obtained are discussed and their plausible interpretation is attempted.

On the corrosion and soiling effects on materials by air pollution in Athens, Greece

NASA Astrophysics Data System (ADS)

Tzanis, C.; Varotsos, C.; Christodoulakis, J.; Tidblad, J.; Ferm, M.; Ionescu, A.; Lefevre, R.-A.; Theodorakopoulou, K.; Kreislova, K.

2010-12-01

In the frame of the European project, entitled MULTI-ASSESS, specimens of structural metals, glass, stone and concrete materials were exposed to air pollution at a station, which was installed for this purpose on a building, located in the centre of Athens. The main purpose of this project was to determine the corrosion and soiling effects of air pollution on materials. A set of the specimens was exposed in a position that was sheltered from rain and partly from wind, and another set was exposed in unsheltered positions on the roof of the above said building. In addition, other specimens were exposed at different heights on the same building, in order to investigate for the first time the corrosion and soiling effects on various materials as a function of height. For the determination of these effects, chemical analysis of the specimens was performed and basic parameters as the weight change, the layer thickness and the optical properties were calculated. Finally, the results obtained are discussed and their plausible interpretation is attempted.

Automatic extraction of building boundaries using aerial LiDAR data

NASA Astrophysics Data System (ADS)

Wang, Ruisheng; Hu, Yong; Wu, Huayi; Wang, Jian

2016-01-01

Building extraction is one of the main research topics of the photogrammetry community. This paper presents automatic algorithms for building boundary extractions from aerial LiDAR data. First, segmenting height information generated from LiDAR data, the outer boundaries of aboveground objects are expressed as closed chains of oriented edge pixels. Then, building boundaries are distinguished from nonbuilding ones by evaluating their shapes. The candidate building boundaries are reconstructed as rectangles or regular polygons by applying new algorithms, following the hypothesis verification paradigm. These algorithms include constrained searching in Hough space, enhanced Hough transformation, and the sequential linking technique. The experimental results show that the proposed algorithms successfully extract building boundaries at rates of 97%, 85%, and 92% for three LiDAR datasets with varying scene complexities.

Bas-relief generation using adaptive histogram equalization.

PubMed

Sun, Xianfang; Rosin, Paul L; Martin, Ralph R; Langbein, Frank C

2009-01-01

An algorithm is presented to automatically generate bas-reliefs based on adaptive histogram equalization (AHE), starting from an input height field. A mesh model may alternatively be provided, in which case a height field is first created via orthogonal or perspective projection. The height field is regularly gridded and treated as an image, enabling a modified AHE method to be used to generate a bas-relief with a user-chosen height range. We modify the original image-contrast-enhancement AHE method to use gradient weights also to enhance the shape features of the bas-relief. To effectively compress the height field, we limit the height-dependent scaling factors used to compute relative height variations in the output from height variations in the input; this prevents any height differences from having too great effect. Results of AHE over different neighborhood sizes are averaged to preserve information at different scales in the resulting bas-relief. Compared to previous approaches, the proposed algorithm is simple and yet largely preserves original shape features. Experiments show that our results are, in general, comparable to and in some cases better than the best previously published methods.

Comparing large eddy simulations and measurements of the turbulent kinetic energy budget in an urban canopy layer

NASA Astrophysics Data System (ADS)

Parlange, M. B.; Giometto, M. G.; Meneveau, C. V.; Fang, J.; Christen, A.

2013-12-01

Local turbulent kinetic energy (TKE) in the Urban Canopy Layer (UCL) is highly dependent on the actual configuration of obstacles relative to mean wind and stability. For many applications, building-resolving information is neither required nor feasible, and simply beyond the numerical capabilities of operational systems. Common urban canopy parameterizations (UCP) used in dispersion and mesoscale forecasting models hence rely on a horizontally averaged approach, where the UCL is represented as a 1D column, often for simplified geometries such as infinite street canyons. We use Large Eddy Simulations (LES) of the airflow over and within a realistic urban geometry in the city of Basel, Switzerland to determine all terms of the TKE budget in order to guide and validate current approaches used in UCPs. A series of high-resolution LES runs of the fully developed flow are performed in order to characterize the TKE budget terms in a horizontally averaged frame of view for various directions of the approaching flow under neutral conditions. Equations are solved on a regular domain with a horizontal resolution of 2 m. A Lagrangian scale-dependent LES model is adopted to parametrize the subgrid-scale stresses and buildings are taken into account adopting an immersed boundary approach with the geometry taken from a highly accurate digital building model. The modeled (periodic) domain is centered on the location of a 32 m tall tower, where measurements of turbulence were performed, during the BUBBLE program in 2001/02 (Rotach et al., Theor. Appl. Clim., 82, 231-261, 2005). Selected terms of the TKE budget were inferred from six levels of ultrasonic anemometer measurements operated over nearly a full year between ground level and two times the mean building height. This contribution answers the questions: (1) How well do TKE budget terms calculated by the LES at the exact tower location match the single point measurements on the tower under comparable conditions? (2) How representative are the single-point measurements at the tower-location compared to the horizontally-averaged TKE budget in the entire urban domain? (3) How important are non-measurable terms of the TKE budget (wake production, dispersive transport, pressure transport) under the current real urban geometry? Our results show good statistical agreement between tower measurements and numerically resolved quantities, validating the model and confirming our immersed boundary approach in the LES a valuable tool to study turbulence and dispersion within real UCLs. Turbulent kinetic energy (TKE) in the UCL is primarily produced at roof-level, and turbulence is transported down into the cavities of the urban canopy (street canyons, backyards). From our results it is also clear how tower measurements cannot be used to quantify all terms in a horizontally-averaged view and the non-measured dispersive terms are important in a real canopy.

A wind tunnel study on the effect of trees on PM2.5 distribution around buildings.

PubMed

Ji, Wenjing; Zhao, Bin

2018-03-15

Vegetation, especially trees, is effective in reducing the concentration of particulate matter. Trees can efficiently capture particles, improve urban air quality, and may further decrease the introduction of outdoor particles to indoor air. The objective of this study is to investigate the effects of trees on particle distribution and removal around buildings using wind tunnel experiments. The wind tunnel is 18m long, 12m wide, and 3.5m high. Trees were modeled using real cypress branches to mimic trees planted around buildings. At the inlet of the wind tunnel, a "line source" of particles was released, simulating air laden with particulate matter. Experiments with the cypress tree and tree-free models were conducted to compare particle concentrations around the buildings. The results indicate that cypress trees clearly reduce PM 2.5 concentrations compared with the tree-free model. The cypress trees enhanced the PM 2.5 removal rate by about 20%. The effects of trees on PM 2.5 removal and distribution vary at different heights. At the base of the trees, their effect on reducing PM 2.5 concentrations is the most significant. At a great height above the treetops, the effect is almost negligible. Copyright © 2017 Elsevier B.V. All rights reserved.

Diameter class volume tables for California old-growth timber

Treesearch

Duncan Dunning

1945-01-01

Tables giving average tree volumes by breast-height diameter classes frequently may be used in timber cruising to save money, time, and men. Such tables may be appropriate in cruises of large areas having many trees in low-intensity cruises warranting the sacrifice in accuracy that results from omission of individual tree height measurements, during wartime when men...

Thinning stagnated ponderosa and Jeffrey pine stands in northeastern California: 30-year effects

Treesearch

Robert J. Lilieholm; Dennis E. Teeguarden; Donald T. Gordon

1989-01-01

Response to precommercial thinning in stagnated 55-year-old ponderosa (Pinus ponderosa Dougl. ex Laws.) and Jeffrey pine (P. jeffreyi Grev. and Balf.) stands in northeastern alifornia was rapid and long-lasting. During the first 5 years after thinning, average annual diameter at breast height (d.b.h.) and height growth of trees on...

Survey of specific gravity of eight Maine conifers

Treesearch

Harold E. Wahlgren; Gregory Baker; Robert R. Maeglin; Arthur C. Hart

1968-01-01

This analysis of a mass increment core sampling of eight coniferous species of Maine characterizes specific gravity for each of the species. No clear-cut relationships of specific gravity to forest type, stand density class, height class, or tree diameter at breast height were found. Included in the data are the species average specific gravity and the range. These...

The Effect of Density on the Height-Diameter Relationship

Treesearch

Boris Zeide; Curtis Vanderschaaf

2002-01-01

Using stand density along with mean diameter to predict average height increases the proportion of explained variance. This result, obtained from permanent plots established in a loblolly pine plantation thinned to different levels, makes sense. We know that due to competition, trees with the same diameter are taller in denser stands. Diameter and density are not only...

Height Response to Harvesting Intensity and Site Preparation in Four Young Loblolly Pine Plantations

Treesearch

Thomas J. Dean; Ray A. Newbold

2002-01-01

A study was conducted to analyze the general effects of harvesting intensity and postharvest treatments on the average, three-year height of loblolly pine (Pinus taeda L.). This was accomplished by analyzing treatment effects across four study sites by treating the locations as random effects in the statistical model. Whole-tree harvesting using...

19. WINDOW DETAIL, NORTH WALL OF GARAGE ADDITION. VIEW SHOWS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. WINDOW DETAIL, NORTH WALL OF GARAGE ADDITION. VIEW SHOWS CONCRETE BLOCK CONSTRUCTION OF ADDITION. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

6. DOUBLE METAL DOORS ON WEST SIDE WITH CABLES ENTERING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. DOUBLE METAL DOORS ON WEST SIDE WITH CABLES ENTERING GROUND AT NORTH END OF BUILDING. - Chollas Heights Naval Radio Transmitting Facility, Helix House, 6410 Zero Road, San Diego, San Diego County, CA

3. OBLIQUE VIEW LOOKING NORTHWEST SHOWING GARAGE EXTENSION WITH DOORS. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. OBLIQUE VIEW LOOKING NORTHWEST SHOWING GARAGE EXTENSION WITH DOORS. VIEW FROM BUILDING 15. - Chollas Heights Naval Radio Transmitting Facility, Public Works Shop, 6410 Zero Road, San Diego, San Diego County, CA

14. DETAIL OF ENTRANCE OVERHANG, WEST SIDE OF NORTH PORTION. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. DETAIL OF ENTRANCE OVERHANG, WEST SIDE OF NORTH PORTION. SAME FEATURE AS A-13. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

Dry granular avalanche impact force on a rigid wall of semi-infinite height

NASA Astrophysics Data System (ADS)

Albaba, Adel; Lambert, Stéphane; Faug, Thierry

2017-06-01

The present paper tackles the problem of the impact of a dry granular avalanche-flow on a rigid wall of semi-infinite height. An analytic force model based on depth-averaged shock theory is proposed to describe the flow-wall interaction and the resulting impact force on the wall. Provided that the analytic force model is fed with the incoming flow conditions regarding thickness, velocity and density, all averaged over a certain distance downstream of the undisturbed incoming flow, it reproduces very well the time history of the impact force actually measured by detailed discrete element simulations, for a wide range of slope angles.

Urban Renewable Building And Neighborhood Optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

URBANopt is a user interface for creating and running district and city scale building energy simulations. The framework is built around the OpenStudio Urban Measures which are part of the OpenStudio project. Building footprints, building height, building type, and other data can be imported from public records or other sources. Footprints and locations for new buildings and district systems can also be specified. OpenStudio Measures are used to create starting point energy models and to model energy design features and efficiency measures for each building. URBANopt allows a user to pose several scenarios such as “what if 30% of themore » commercial retail buildings added roof top solar” or “what if all elementary schools converted to ground source heat pumps” and then visualize the impacts at a district or city scale. URBANopt is capable of modeling existing buildings, new construction, and district energy systems. URBANopt can be used to explore options for achieving Zero Energy across a collection of buildings (e.g., Zero Energy Districts).« less

Corrections for the effects of significant wave height and attitude on Geosat radar altimeter measurements

NASA Technical Reports Server (NTRS)

Hayne, G. S.; Hancock, D. W., III

1990-01-01

Range estimates from a radar altimeter have biases which are a function of the significant wave height (SWH) and the satellite attitude angle (AA). Based on results of prelaunch Geosat modeling and simulation, a correction for SWH and AA was already applied to the sea-surface height estimates from Geosat's production data processing. By fitting a detailed model radar return waveform to Geosat waveform sampler data, it is possible to provide independent estimates of the height bias, the SWH, and the AA. The waveform fitting has been carried out for 10-sec averages of Geosat waveform sampler data over a wide range of SWH and AA values. The results confirm that Geosat sea-surface-height correction is good to well within the original dm-level specification, but that an additional height correction can be made at the level of several cm.

Intra- and intergenerational social mobility in relation to height, weight and body mass index in a British national cohort.

PubMed

Krzyżanowska, Monika; Mascie-Taylor, C G Nicholas

2011-09-01

Using a sample of 2090 father and son pairs, the extent of intra- and inter-generational social mobility (migration between social classes) was examined over a 42-year period in a British cohort in relation to height, weight and body mass index (BMI). The mean height difference between the highest and lowest social class decreased from about 4 cm in the fathers' generation to about 3 cm in the sons' generation, indicating a decline in heterogeneity in height between classes. For fathers downward intra-generational social mobility ranged between 11% and 18% while between 16% and 26% were upwardly mobile; for sons 15% were downwardly mobile and 21% upwardly mobile. On average downwardly mobile fathers were shorter by between 0.1 cm and 0.7 cm while upwardly mobile fathers were taller by, on average, 0.6 cm to 1.7 cm. For sons, the downwardly mobile were on average 0.7 cm shorter and the upwardly mobile 0.8 cm taller. For weight and BMI there were no consistent relationships with intra-generational mobility in either the fathers' or sons' generations. Inter-generationally, between 18% and 19% of sons were downwardly mobile and between 39% and 40% were upwardly mobile; the downwardly mobile were shorter by about 0.9 cm and the upwardly taller by between 0.6 cm and 1.2 cm. Sons with higher BMI were more likely to be inter-generationally downwardly mobile.

Pollutant Concentrations in Street Canyons of Different Aspect Ratio with Avenues of Trees for Various Wind Directions

NASA Astrophysics Data System (ADS)

Gromke, Christof; Ruck, Bodo

2012-07-01

This study summarizes the effects of avenues of trees in urban street canyons on traffic pollutant dispersion. We describe various wind-tunnel experiments with different tree-avenue models in combination with variations in street-canyon aspect ratio W/ H (with W the street-canyon width and H the building height) and approaching wind direction. Compared to tree-free street canyons, in general, higher pollutant concentrations are found. Avenues of trees do not suppress canyon vortices, although the air ventilation in canyons is hindered significantly. For a perpendicular wind direction, increases in wall-average and wall-maximum concentrations at the leeward canyon wall and decreases in wall-average concentrations at the windward wall are found. For oblique and perpendicular wind directions, increases at both canyon walls are obtained. The strongest effects of avenues of trees on traffic pollutant dispersion are observed for oblique wind directions for which also the largest concentrations at the canyon walls are found. Thus, the prevailing assumption that attributes the most harmful dispersion conditions to a perpendicular wind direction does not hold for street canyons with avenues of trees. Furthermore, following dimensional analysis, an estimate of the normalized wall-maximum traffic pollutant concentration in street canyons with avenues of trees is derived.

Effect of tank geometry on its average performance

NASA Astrophysics Data System (ADS)

Orlov, Aleksey A.; Tsimbalyuk, Alexandr F.; Malyugin, Roman V.; Leontieva, Daria A.; Kotelnikova, Alexandra A.

2018-03-01

The mathematical model of non-stationary filling of vertical submerged tanks with gaseous uranium hexafluoride is presented in the paper. There are calculations of the average productivity, heat exchange area, and filling time of various volumes tanks with smooth inner walls depending on their "height : radius" ratio as well as the average productivity, degree, and filling time of horizontal ribbing tank with volume 6.10-2 m3 with change central hole diameter of the ribs. It has been shown that the growth of "height / radius" ratio in tanks with smooth inner walls up to the limiting values allows significantly increasing tank average productivity and reducing its filling time. Growth of H/R ratio of tank with volume 1.0 m3 to the limiting values (in comparison with the standard tank having H/R equal 3.49) augments tank productivity by 23.5 % and the heat exchange area by 20%. Besides, we have demonstrated that maximum average productivity and a minimum filling time are reached for the tank with volume 6.10-2 m3 having central hole diameter of horizontal ribs 6.4.10-2 m.

Intra-annual height increment of Pinus sylvestris at high latitudes in Finland.

PubMed

Salminen, Hannu; Jalkanen, Risto

2007-09-01

Intra-annual height growth of Scots pine (Pinus sylvestris L.) in four stands was followed for up to four growing seasons (2000-2003) in the northern boreal zone in Lapland. Elongation of the leader shoot correlated with temperature sum expressed as degree-days. Total length of the leader shoot correlated with growth rate but not with duration of the height-growth period. The longer the annual shoot at the end of the season, the greater the height increment per degree- and growing day. Height-growth cessation was defined as the date when 95% of the total shoot length was achieved. In all stands and all years, height growth ceased when, on average, 41% of the relative temperature sum of the site was achieved (range of variation 38-43%). The relative temperature sum was calculated by dividing the actual temperature sum by the long-term mean for the site. Our results suggest that annual height growth is finished when a location-specific temperature sum threshold is attained.

Minimum Abutment Height to Eliminate Bone Loss: Influence of Implant Neck Design and Platform Switching.

PubMed

Spinato, Sergio; Galindo-Moreno, Pablo; Bernardello, Fabio; Zaffe, Davide

This retrospective study quantitatively analyzed the minimum prosthetic abutment height to eliminate bone loss after 4.7-mm-diameter implant placement in maxillary bone and how grafting techniques can affect the marginal bone loss in implants placed in maxillary areas. Two different implant types with a similar neck design were singularly placed in two groups of patients: the test group, with platform-switched implants, and the control group, with conventional (non-platform-switched) implants. Patients requiring bone augmentation underwent unilateral sinus augmentation using a transcrestal technique with mineralized xenograft. Radiographs were taken immediately after implant placement, after delivery of the prosthetic restoration, and after 12 months of loading. The average mesial and distal marginal bone loss of the control group (25 patients) was significantly more than twice that of the test group (26 patients), while their average abutment height was similar. Linear regression analysis highlighted a statistically significant inverse relationship between marginal bone loss and abutment height in both groups; however, the intercept of the regression line, both mesially and distally, was 50% lower for the test group than for the control group. The marginal bone loss was annulled with an abutment height of 2.5 mm for the test group and 3.0 mm for the control group. No statistically significant differences were found regarding marginal bone loss of implants placed in native maxillary bone compared with those placed in the grafted areas. The results suggest that the shorter the abutment height, the greater the marginal bone loss in cement-retained prostheses. Abutment height showed a greater influence in platform-switched than in non-platform-switched implants on the limitation of marginal bone loss.

Estimation of Genetic Relationships Between Individuals Across Cohorts and Platforms: Application to Childhood Height.

PubMed

Fedko, Iryna O; Hottenga, Jouke-Jan; Medina-Gomez, Carolina; Pappa, Irene; van Beijsterveldt, Catharina E M; Ehli, Erik A; Davies, Gareth E; Rivadeneira, Fernando; Tiemeier, Henning; Swertz, Morris A; Middeldorp, Christel M; Bartels, Meike; Boomsma, Dorret I

2015-09-01

Combining genotype data across cohorts increases power to estimate the heritability due to common single nucleotide polymorphisms (SNPs), based on analyzing a Genetic Relationship Matrix (GRM). However, the combination of SNP data across multiple cohorts may lead to stratification, when for example, different genotyping platforms are used. In the current study, we address issues of combining SNP data from different cohorts, the Netherlands Twin Register (NTR) and the Generation R (GENR) study. Both cohorts include children of Northern European Dutch background (N = 3102 + 2826, respectively) who were genotyped on different platforms. We explore imputation and phasing as a tool and compare three GRM-building strategies, when data from two cohorts are (1) just combined, (2) pre-combined and cross-platform imputed and (3) cross-platform imputed and post-combined. We test these three strategies with data on childhood height for unrelated individuals (N = 3124, average age 6.7 years) to explore their effect on SNP-heritability estimates and compare results to those obtained from the independent studies. All combination strategies result in SNP-heritability estimates with a standard error smaller than those of the independent studies. We did not observe significant difference in estimates of SNP-heritability based on various cross-platform imputed GRMs. SNP-heritability of childhood height was on average estimated as 0.50 (SE = 0.10). Introducing cohort as a covariate resulted in ≈2 % drop. Principal components (PCs) adjustment resulted in SNP-heritability estimates of about 0.39 (SE = 0.11). Strikingly, we did not find significant difference between cross-platform imputed and combined GRMs. All estimates were significant regardless the use of PCs adjustment. Based on these analyses we conclude that imputation with a reference set helps to increase power to estimate SNP-heritability by combining cohorts of the same ethnicity genotyped on different platforms. However, important factors should be taken into account such as remaining cohort stratification after imputation and/or phenotypic heterogeneity between and within cohorts. Whether one should use imputation, or just combine the genotype data, depends on the number of overlapping SNPs in relation to the total number of genotyped SNPs for both cohorts, and their ability to tag all the genetic variance related to the specific trait of interest.

Airborne laser scanning for forest health status assessment and radiative transfer modelling

NASA Astrophysics Data System (ADS)

Novotny, Jan; Zemek, Frantisek; Pikl, Miroslav; Janoutova, Ruzena

2013-04-01

Structural parameters of forest stands/ecosystems are an important complementary source of information to spectral signatures obtained from airborne imaging spectroscopy when quantitative assessment of forest stands are in the focus, such as estimation of forest biomass, biochemical properties (e.g. chlorophyll /water content), etc. The parameterization of radiative transfer (RT) models used in latter case requires three-dimensional spatial distribution of green foliage and woody biomass. Airborne LiDAR data acquired over forest sites bears these kinds of 3D information. The main objective of the study was to compare the results from several approaches to interpolation of digital elevation model (DEM) and digital surface model (DSM). We worked with airborne LiDAR data with different density (TopEye Mk II 1,064nm instrument, 1-5 points/m2) acquired over the Norway spruce forests situated in the Beskydy Mountains, the Czech Republic. Three different interpolation algorithms with increasing complexity were tested: i/Nearest neighbour approach implemented in the BCAL software package (Idaho Univ.); ii/Averaging and linear interpolation techniques used in the OPALS software (Vienna Univ. of Technology); iii/Active contour technique implemented in the TreeVis software (Univ. of Freiburg). We defined two spatial resolutions for the resulting coupled raster DEMs and DSMs outputs: 0.4 m and 1 m, calculated by each algorithm. The grids correspond to the same spatial resolutions of hyperspectral imagery data for which the DEMs were used in a/geometrical correction and b/building a complex tree models for radiative transfer modelling. We applied two types of analyses when comparing between results from the different interpolations/raster resolution: 1/calculated DEM or DSM between themselves; 2/comparison with field data: DEM with measurements from referential GPS, DSM - field tree alometric measurements, where tree height was calculated as DSM-DEM. The results of the analyses show that: 1/averaging techniques tend to underestimate the tree height and the generated surface does not follow the first LiDAR echoes both for 1 m and 0.4 m pixel size; 2/we did not find any significant difference between tree heights calculated by nearest neighbour algorithm and the active contour technique for 1 m pixel output but the difference increased with finer resolution (0.4 m); 3/the accuracy of the DEMs calculated by tested algorithms is similar.

Photocurrent modulation under dual excitation in individual GaN nanowires.

PubMed

Yadav, Shivesh; Deb, Swarup; Gupta, Kantimay Das; Dhar, Subhabrata

2018-06-21

The photo-response properties of vapor-liquid-solid (VLS) grown [101[combining macron]0] oriented individual GaN nanowires of the diameter ranging from 30 to 100 nm are investigated under the joint illumination of above and sub-bandgap lights. When illuminated with above-bandgap light, these wires show persistent photoconductivity (PPC) effects with long build-up and decay times. The study reveals the quenching of photoconductivity (PC) upon illumination with an additional sub-bandgap light. PC recovers when the sub-bandgap illumination is withdrawn. A rate equation model attributing the PPC effect to the entrapment of photo-generated holes in the surface states and the PC quenching effect on the sub-bandgap light driven release of the holes from the trapped states has been proposed. The average height of the capture barrier has been found to be about 400 meV. The study also suggests that the capture barrier has a broad distribution with an upper cut-off energy of ∼2 eV.

Accuracy assessment of TanDEM-X IDEM using airborne LiDAR on the area of Poland

NASA Astrophysics Data System (ADS)

Woroszkiewicz, Małgorzata; Ewiak, Ireneusz; Lulkowska, Paulina

2017-06-01

The TerraSAR-X add-on for Digital Elevation Measurement (TanDEM-X) mission launched in 2010 is another programme - after the Shuttle Radar Topography Mission (SRTM) in 2000 - that uses space-borne radar interferometry to build a global digital surface model. This article presents the accuracy assessment of the TanDEM-X intermediate Digital Elevation Model (IDEM) provided by the German Aerospace Center (DLR) under the project "Accuracy assessment of a Digital Elevation Model based on TanDEM-X data" for the southwestern territory of Poland. The study area included: open terrain, urban terrain and forested terrain. Based on a set of 17,498 reference points acquired by airborne laser scanning, the mean errors of average heights and standard deviations were calculated for areas with a terrain slope below 2 degrees, between 2 and 6 degrees and above 6 degrees. The absolute accuracy of the IDEM data for the analysed area, expressed as a root mean square error (Total RMSE), was 0.77 m.

Design of exchange-correlation functionals through the correlation factor approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pavlíková Přecechtělová, Jana, E-mail: j.precechtelova@gmail.com, E-mail: Matthias.Ernzerhof@UMontreal.ca; Institut für Chemie, Theoretische Chemie / Quantenchemie, Sekr. C7, Technische Universität Berlin, Straße des 17. Juni 135, 10623 Berlin; Bahmann, Hilke

The correlation factor model is developed in which the spherically averaged exchange-correlation hole of Kohn-Sham theory is factorized into an exchange hole model and a correlation factor. The exchange hole model reproduces the exact exchange energy per particle. The correlation factor is constructed in such a manner that the exchange-correlation energy correctly reduces to exact exchange in the high density and rapidly varying limits. Four different correlation factor models are presented which satisfy varying sets of physical constraints. Three models are free from empirical adjustments to experimental data, while one correlation factor model draws on one empirical parameter. The correlationmore » factor models are derived in detail and the resulting exchange-correlation holes are analyzed. Furthermore, the exchange-correlation energies obtained from the correlation factor models are employed to calculate total energies, atomization energies, and barrier heights. It is shown that accurate, non-empirical functionals can be constructed building on exact exchange. Avenues for further improvements are outlined as well.« less

Approaching the resolution limit of W-C nano-gaps using focused ion beam chemical vapour deposition

NASA Astrophysics Data System (ADS)

Dai, Jun; Chang, Hui; Maeda, Etsuo; Warisawa, Shin'ichi; Kometani, Reo

2018-01-01

Nano-gaps are fundamental building blocks for nanochannels, plasmonic nanostructures and superconducting Josephson junctions. We present a systematic study on the formation mechanism and resolution limit of W-C nano-gaps fabricated using focused-ion-beam chemical vapour deposition (FIB-CVD). First, the deposition size of the nanostructures is evaluated. The size averaged over 100 dots is 32 nm at FWHM. Line and space are also fabricated with the smallest size, having a spacing of only 5 nm at FWHM. Then, a model is developed to study the formation mechanism and provides the design basis for W-C nano-gaps. Both experimental and simulation results reveal that the shrinkage of W-C nano-gaps is accelerated as the Gaussian parts of the nano-wire profiles overlap. A Nano-gap with a length of 5 nm and height difference as high as 42 nm is synthesized. We believe that FIB-CVD opens avenues for novel functional nanodevices that can be potentially used for biosensing, photodetecting, or quantum computing.

a Method for the Seamlines Network Automatic Selection Based on Building Vector

NASA Astrophysics Data System (ADS)

Li, P.; Dong, Y.; Hu, Y.; Li, X.; Tan, P.

2018-04-01

In order to improve the efficiency of large scale orthophoto production of city, this paper presents a method for automatic selection of seamlines network in large scale orthophoto based on the buildings' vector. Firstly, a simple model of the building is built by combining building's vector, height and DEM, and the imaging area of the building on single DOM is obtained. Then, the initial Voronoi network of the measurement area is automatically generated based on the positions of the bottom of all images. Finally, the final seamlines network is obtained by optimizing all nodes and seamlines in the network automatically based on the imaging areas of the buildings. The experimental results show that the proposed method can not only get around the building seamlines network quickly, but also remain the Voronoi network' characteristics of projection distortion minimum theory, which can solve the problem of automatic selection of orthophoto seamlines network in image mosaicking effectively.

Modeling vegetation heights from high resolution stereo aerial photography: an application for broad-scale rangeland monitoring.

PubMed

Gillan, Jeffrey K; Karl, Jason W; Duniway, Michael; Elaksher, Ahmed

2014-11-01

Vertical vegetation structure in rangeland ecosystems can be a valuable indicator for assessing rangeland health and monitoring riparian areas, post-fire recovery, available forage for livestock, and wildlife habitat. Federal land management agencies are directed to monitor and manage rangelands at landscapes scales, but traditional field methods for measuring vegetation heights are often too costly and time consuming to apply at these broad scales. Most emerging remote sensing techniques capable of measuring surface and vegetation height (e.g., LiDAR or synthetic aperture radar) are often too expensive, and require specialized sensors. An alternative remote sensing approach that is potentially more practical for managers is to measure vegetation heights from digital stereo aerial photographs. As aerial photography is already commonly used for rangeland monitoring, acquiring it in stereo enables three-dimensional modeling and estimation of vegetation height. The purpose of this study was to test the feasibility and accuracy of estimating shrub heights from high-resolution (HR, 3-cm ground sampling distance) digital stereo-pair aerial images. Overlapping HR imagery was taken in March 2009 near Lake Mead, Nevada and 5-cm resolution digital surface models (DSMs) were created by photogrammetric methods (aerial triangulation, digital image matching) for twenty-six test plots. We compared the heights of individual shrubs and plot averages derived from the DSMs to field measurements. We found strong positive correlations between field and image measurements for several metrics. Individual shrub heights tended to be underestimated in the imagery, however, accuracy was higher for dense, compact shrubs compared with shrubs with thin branches. Plot averages of shrub height from DSMs were also strongly correlated to field measurements but consistently underestimated. Grasses and forbs were generally too small to be detected with the resolution of the DSMs. Estimates of vertical structure will be more accurate in plots having low herbaceous cover and high amounts of dense shrubs. Through the use of statistically derived correction factors or choosing field methods that better correlate with the imagery, vegetation heights from HR DSMs could be a valuable technique for broad-scale rangeland monitoring needs. Copyright © 2014 Elsevier Ltd. All rights reserved.

Modeling vegetation heights from high resolution stereo aerial photography: an application for broad-scale rangeland monitoring

USGS Publications Warehouse

Gillan, Jeffrey K.; Karl, Jason W.; Duniway, Michael; Elaksher, Ahmed

2014-01-01

Vertical vegetation structure in rangeland ecosystems can be a valuable indicator for assessing rangeland health and monitoring riparian areas, post-fire recovery, available forage for livestock, and wildlife habitat. Federal land management agencies are directed to monitor and manage rangelands at landscapes scales, but traditional field methods for measuring vegetation heights are often too costly and time consuming to apply at these broad scales. Most emerging remote sensing techniques capable of measuring surface and vegetation height (e.g., LiDAR or synthetic aperture radar) are often too expensive, and require specialized sensors. An alternative remote sensing approach that is potentially more practical for managers is to measure vegetation heights from digital stereo aerial photographs. As aerial photography is already commonly used for rangeland monitoring, acquiring it in stereo enables three-dimensional modeling and estimation of vegetation height. The purpose of this study was to test the feasibility and accuracy of estimating shrub heights from high-resolution (HR, 3-cm ground sampling distance) digital stereo-pair aerial images. Overlapping HR imagery was taken in March 2009 near Lake Mead, Nevada and 5-cm resolution digital surface models (DSMs) were created by photogrammetric methods (aerial triangulation, digital image matching) for twenty-six test plots. We compared the heights of individual shrubs and plot averages derived from the DSMs to field measurements. We found strong positive correlations between field and image measurements for several metrics. Individual shrub heights tended to be underestimated in the imagery, however, accuracy was higher for dense, compact shrubs compared with shrubs with thin branches. Plot averages of shrub height from DSMs were also strongly correlated to field measurements but consistently underestimated. Grasses and forbs were generally too small to be detected with the resolution of the DSMs. Estimates of vertical structure will be more accurate in plots having low herbaceous cover and high amounts of dense shrubs. Through the use of statistically derived correction factors or choosing field methods that better correlate with the imagery, vegetation heights from HR DSMs could be a valuable technique for broad-scale rangeland monitoring needs.

Bi-Pedicle Fixation of Affected Vertebra in Thoracolumbar Burst Fracture.

PubMed

Padalkar, Pravin; Mehta, Varshil

2017-04-01

Burst fractures of the spine account for 14% of all spinal injuries and more than 50% of all thoracolumbar trauma. However, there is ambiguity while choosing the right treatment plan. Short Segment Pedicle screw Fixation (SSPF) has become an increasingly popular method of treatment of thoracolumbar burst fractures, providing the advantage of incorporating fewer motion segments in the fixation. Various biomechanical studies showed that the use of pedicle screws could achieve stable construct within short-segment fixation. To evaluate the efficacy of SSPF using longest possible screws in both pedicles of fractured vertebra. A retrospective chart review of 25 single burst thoracolumbar fracture patients, operated between May 2009 to 2015 in a tertiary care trauma center, was conducted. Preoperative and post-operative plain radiographs were evaluated for kyphotic angulations using the traditional Cobb method. Anterior Vertebral Height (AVH), Posteriors Vertebral Height (PVH) were measured preoperatively and immediate postoperatively. Average percentage loss of AVH and mid-sagittal height were calculated on preoperative and postoperative X-rays on follow up. Fourteen men and 11 women with an average age of 42.92 years comprised the study population. Mean age at the time of operation was 34.5±14.2 years. Mean operation time was 168±72 (minutes). Average hospitalization time was 9±7 (days). Mean blood loss was 515±485 (ml). There were two cases of postoperative infection and implant failure each. A mean of 15.2° of kyphosis correction was attained from pre-operation to post-operation (p<0.0001). Although, there was a 15° average improvement of kyphosis post-fixation, loss of correction over time was nearly 8°, resulting in a 7° mean correction of kyphosis. A mean loss of AVH on postoperative radiograph was 6.12% and maintained 12.4% at the time of review (p<0.001). Similarly, there was 32.8% mid-sagittal height loss at time of injury, which was improved to only 12.6% as compare to initial height loss (p<0.0001). In this study, we propose SSPF using longest possible screws in both pedicle of fractured vertebra. Bi-pedicular fixation gives significant radiological corrections.

1. WEST SIDE. VIEW SHOWS CLERESTORY WINDOWS IN ROOF AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. WEST SIDE. VIEW SHOWS CLERESTORY WINDOWS IN ROOF AND RELATIONSHIP WITH BUILDING 13 AT RIGHT. - Chollas Heights Naval Radio Transmitting Facility, Public Works Shop, 6410 Zero Road, San Diego, San Diego County, CA

22. INTERIOR OF SOUTHERN ROOM LOOKING SOUTH TOWARD DOORS AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. INTERIOR OF SOUTHERN ROOM LOOKING SOUTH TOWARD DOORS AND WINDOWS. EARLY TENSION DEVICE VISIBLE ABOVE DOORWAY. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

Analysis of Reaction Times and Aerobic Capacities of Soccer Players According to Their Playing Positions

ERIC Educational Resources Information Center

Taskin, Cengiz; Karakoc, Onder; Taskin, Mine; Dural, Murat

2016-01-01

70 soccer players in Gaziantep amateur league voluntarily participated in this study, (average of their ages 19,17±1,34years, average of their heights 181,28±5,06 cm, average of their body weights 76,75±4,43 kg and average of their sports experiences 3,78±0,95 years) to analyze visual and auditory reaction times and aerobic capacities of amateur…

Estimating Planetary Boundary Layer Heights from NOAA Profiler Network Wind Profiler Data

NASA Technical Reports Server (NTRS)

Molod, Andrea M.; Salmun, H.; Dempsey, M

2015-01-01

An algorithm was developed to estimate planetary boundary layer (PBL) heights from hourly archived wind profiler data from the NOAA Profiler Network (NPN) sites located throughout the central United States. Unlike previous studies, the present algorithm has been applied to a long record of publicly available wind profiler signal backscatter data. Under clear conditions, summertime averaged hourly time series of PBL heights compare well with Richardson-number based estimates at the few NPN stations with hourly temperature measurements. Comparisons with clear sky reanalysis based estimates show that the wind profiler PBL heights are lower by approximately 250-500 m. The geographical distribution of daily maximum PBL heights corresponds well with the expected distribution based on patterns of surface temperature and soil moisture. Wind profiler PBL heights were also estimated under mostly cloudy conditions, and are generally higher than both the Richardson number based and reanalysis PBL heights, resulting in a smaller clear-cloudy condition difference. The algorithm presented here was shown to provide a reliable summertime climatology of daytime hourly PBL heights throughout the central United States.

Automated lidar-derived canopy height estimates for the Upper Mississippi River System

USGS Publications Warehouse

Hlavacek, Enrika

2015-01-01

Land cover/land use (LCU) classifications serve as important decision support products for researchers and land managers. The LCU classifications produced by the U.S. Geological Survey’s Upper Midwest Environmental Sciences Center (UMESC) include canopy height estimates that are assigned through manual aerial photography interpretation techniques. In an effort to improve upon these techniques, this project investigated the use of high-density lidar data for the Upper Mississippi River System to determine canopy height. An ArcGIS tool was developed to automatically derive height modifier information based on the extent of land cover features for forest classes. The measurement of canopy height included a calculation of the average height from lidar point cloud data as well as the inclusion of a local maximum filter to identify individual tree canopies. Results were compared to original manually interpreted height modifiers and to field survey data from U.S. Forest Service Forest Inventory and Analysis plots. This project demonstrated the effectiveness of utilizing lidar data to more efficiently assign height modifier attributes to LCU classifications produced by the UMESC.

Acoustic and Perceptual Measures of SATB Choir Performances on Two Types of Portable Choral Riser Units in Three Singer-Spacing Conditions

ERIC Educational Resources Information Center

Daugherty, James F.; Manternach, Jeremy N.; Brunkan, Melissa C.

2013-01-01

Under controlled conditions, we assessed acoustically (long-term average spectra) and perceptually (singer survey, listener survey) six performances of an soprano, alto, tenor, and bass (SATB) choir ("N" = 27) as it sang the same musical excerpt on two portable riser units (standard riser step height, taller riser step height) with…

Fifteen-Year Growth of Six Planted Hardwood Species on Sharkey Clay Soil

Treesearch

Roger M. Krinard; Harvey E. Kennedy

1987-01-01

Six hardwood species planted on Sharkey clay soil that had been disked the first 5 years for weed control were significantly taller at age 5 when compared to species grown on mowed sites. By age 15, there were no differences in heights within species except for sweet pecan. Average heights by species at age 15 were: cottonwood (Populus deltoides...

Mesavage and Girard form class taper functions derived from profile equations

Treesearch

Thomas g. Matney; Emily B. Schultz

2007-01-01

The Mesavage and Girard (1946) average upper-log taper tables remain a favorite way of estimating tree bole volume because they only require the measurement of merchantable (useable) height to an indefinite top diameter limit. For the direct application of profile equations, height must be measured to a definite top diameter limit, and this makes the collection of data...

Growth Comparisons of Planted Sweetgum and Sycamore

Treesearch

R. M. Krinard

1988-01-01

From age 18 through age 23, average annual growth of planted sweetgum (Liquidambar styraciflua L.) on Commerce silt loam exceeded growth of sweetgum on Sharkey clay by about 45 percent in diameter at breast height (d.b.h.) and height, 75 percent in basal area, and more than three times in cubic volume. At age 18 on the Commerce soil, sycamore (

Effects of cutting time, stump height, parent tree characteristics, and harvest variables on development of bigleaf maple sprout clumps

USGS Publications Warehouse

Tappeiner, J. C.; Zasada, J.; Maxwell, B.

1996-01-01

In order to determine the effects of stump height, year of cutting, parent-tree size, logging damage, and deer browsing on bigleaf maple (Acer macrophyllum) sprout clump development, maple trees were cut to two stump heights at three different times. Stump height had the greatest impact on sprout clump size. Two years after clearcutting, the sprout clump volume for short stumps was significantly less than that for tall stumps. The sprout clump volume, area, and number of sprouts were significantly less for trees cut 1 and 2 yr before harvest than for trees cut at harvest. Sprout clump size was positively correlated with parent tree stem diameter and stump volume, and negatively correlated with the percentage of bark removed during logging. Browsing had no significant impact on average clump size. Uncut trees produced sprout clumps at their base and epicormic branches along the length of their stems; thus their crown volume averaged four to five times that of cut trees. Cutting maple in clearcuts to low stumps may reduce maple competition with Douglas-fir regeneration and still maintain maple in the next stand.

Observations of sea ice ridging in the Weddell Sea

NASA Astrophysics Data System (ADS)

Granberg, Hardy B.; Leppaäranta, Matti

1999-11-01

Sea ice surface topography data were obtained by helicopter-borne laser profiling during the First Finnish Antarctic Expedition (FINNARP-89). The measurements were made near the ice margin at about 73°S, 27°W in the eastern Weddell Sea on December 31, 1989, and January 1, 1990. Five transects, ranging in length from 127 to 163 km and covering a total length of 724 km, are analyzed. With a lower cutoff of 0.91 m the overall ridge frequency was 8.4 ridges/km and the average ridge height was 1.32 m. The spatial variations in ridging were large; for 36 individual 20-km segments the frequencies were 2-16 ridges/km and the mean heights were 1.16-1.56 m. The frequencies and mean heights were weakly correlated. The distributions of the ridge heights followed the exponential distribution; the spacings did not pass tests for either the exponential or the lognormal distribution, but the latter was much closer. In the 20-km segments the areally averaged thickness of ridged ice was 0.51±0.28 m, ranging from 0.10 to 1.15 m. The observed ridge size and frequency are greater than those known for the Ross Sea. Compared with the central Arctic, the Weddell Sea ridging frequencies are similar but the ridge heights are smaller, possibly as a result of differences in snow accumulation.

Three-dimensional morphology of the palate in subjects with isolated cleft palate at the stage of permanent dentition.

PubMed

Smahel, Zbynek; Trefný, Pavel; Formánek, Pavel; Müllerová, Ziva; Peterka, Miroslav

2003-11-01

Three-dimensional analysis of palate size and shape in patients with isolated cleft palate at the stage of permanent dentition. Cross-sectional study using Fourier transform profilometry. Twenty-nine randomly selected dental casts of approximately 15-year-old boys with isolated cleft palate and 28 dental casts of normal boys of the same age. All patients were operated on by the same method (pushback and pharyngeal flap surgery) at a mean age of 4.5 years. Data on the palate height in 210 defined locations (pixels). The palate in isolated clefts is narrower throughout its whole extent and lower from the level of the first premolars. The difference, as compared with controls, increases in a posterior direction. At the level of the first molars, palatal height is reduced by one-quarter, the area of the transversal section by more than one-third. The shaping of the palate vault is, on average, symmetrical with a marked interindividual variability. Palatal height does not depend on the width of the dentoalveolar arch, and the height of the primary palate is not reduced. The smaller width and reduced height from the level of the first premolars posteriorly confirm the substantially reduced space available for the tongue in patients with isolated cleft palate. Deviations are on the average symmetrical, and the anterior part of the palate is not shallower.

ANEMOS: A computer code to estimate air concentrations and ground deposition rates for atmospheric nuclides emitted from multiple operating sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, C.W.; Sjoreen, A.L.; Begovich, C.L.

This code estimates concentrations in air and ground deposition rates for Atmospheric Nuclides Emitted from Multiple Operating Sources. ANEMOS is one component of an integrated Computerized Radiological Risk Investigation System (CRRIS) developed for the US Environmental Protection Agency (EPA) for use in performing radiological assessments and in developing radiation standards. The concentrations and deposition rates calculated by ANEMOS are used in subsequent portions of the CRRIS for estimating doses and risks to man. The calculations made in ANEMOS are based on the use of a straight-line Gaussian plume atmospheric dispersion model with both dry and wet deposition parameter options. Themore » code will accommodate a ground-level or elevated point and area source or windblown source. Adjustments may be made during the calculations for surface roughness, building wake effects, terrain height, wind speed at the height of release, the variation in plume rise as a function of downwind distance, and the in-growth and decay of daughter products in the plume as it travels downwind. ANEMOS can also accommodate multiple particle sizes and clearance classes, and it may be used to calculate the dose from a finite plume of gamma-ray-emitting radionuclides passing overhead. The output of this code is presented for 16 sectors of a circular grid. ANEMOS can calculate both the sector-average concentrations and deposition rates at a given set of downwind distances in each sector and the average of these quantities over an area within each sector bounded by two successive downwind distances. ANEMOS is designed to be used primarily for continuous, long-term radionuclide releases. This report describes the models used in the code, their computer implementation, the uncertainty associated with their use, and the use of ANEMOS in conjunction with other codes in the CRRIS. A listing of the code is included in Appendix C.« less

An algorithm to estimate PBL heights from wind profiler data

NASA Astrophysics Data System (ADS)

Molod, A.; Salmun, H.

2016-12-01

An algorithm was developed to estimate planetary boundary layer (PBL) heights from hourlyarchived wind profiler data from the NOAA Profiler Network (NPN) sites located throughoutthe central United States from the period 1992-2012. The long period of record allows ananalysis of climatological mean PBL heights as well as some estimates of year to yearvariability. Under clear conditions, summertime averaged hourly time series of PBL heightscompare well with Richardson-number based estimates at the few NPN stations with hourlytemperature measurements. Comparisons with clear sky MERRA estimates show that the windprofiler (WP) and the Richardson number based PBL heights are lower by approximately 250-500 m.The geographical distribution of daily maximum WP PBL heights corresponds well with theexpected distribution based on patterns of surface temperature and soil moisture. Windprofiler PBL heights were also estimated under mostly cloudy conditions, but the WP estimatesshow a smaller clear-cloudy condition difference than either of the other two PBL height estimates.The algorithm presented here is shown to provide a reliable summer, fall and springclimatology of daytime hourly PBL heights throughout the central United States. The reliabilityof the algorithm has prompted its use to obtain hourly PBL heights from other archived windprofiler data located throughout the world.

In Situ Height and Width Estimation of Sorghum Plants from 2.5d Infrared Images

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baharav, Tavor; Bariya, Mohini; Zakhor, Avideh

Plant phenotyping, or the measurement of plant traits such as stem width and plant height, is a critical step in the development and evaluation of higher yield biofuel crops. Phenotyping allows biologists to quantitatively estimate the biomass of plant varieties and therefore their potential for biofuel production. Manual phenotyping is costly, time-consuming, and errorprone, requiring a person to walk through the fields measuring individual plants with a tape measure and notebook. In this work we describe an alternative system consisting of an autonomous robot equipped with two infrared cameras that travels through fields, collecting 2.5D image data of sorghum plants.more » We develop novel image processing based algorithms to estimate plant height and stem width from the image data. Our proposed method has the advantage of working in situ using images of plants from only one side. This allows phenotypic data to be collected nondestructively throughout the growing cycle, providing biologists with valuable information on crop growth patterns. Our approach first estimates plant heights and stem widths from individual frames. It then uses tracking algorithms to refine these estimates across frames and avoid double counting the same plant in multiple frames. The result is a histogram of stem widths and plant heights for each plot of a particular genetically engineered sorghum variety. In-field testing and comparison with human collected ground truth data demonstrates that our system achieves 13% average absolute error for stem width estimation and 15% average absolute error for plant height estimation.« less

Impact of long-term erythrocytapheresis on growth and peak height velocity of children with sickle cell disease.

PubMed

Bavle, Abhishek; Raj, Ashok; Kong, Maiying; Bertolone, Salvatore

2014-11-01

Children with sickle cell disease (SCD) lag in weight and height and have a delayed growth spurt compared to normal children. We studied the effect of long-term erythrocytapheresis (LTE) on the growth of children with SCD and the age at which they attained peak height velocity. A retrospective chart review was performed recording weight, height, and body mass index (BMI) measurements of 36 patients with SCD who received LTE every 3-5 weeks for an average duration of 5 years. The z-scores for weight, height, and BMI of these patients were compared with that of patients with SCD from the Cooperative Study of Sickle Cell Disease (CSSCD) and a sub-set of 64 controls matched for age, sex, and initial growth parameter z-scores at the start of LTE. The z-scores for all parameters improved significantly for our patients on LTE compared to match controls from CSSCD and the entire pediatric CSSCD cohort (P-value: <0.01). Peak height velocity was achieved 2 months earlier for females (P-value: 0.94) and 11 months earlier for males (P-value: 0.02), who started LTE before 14 years of age, compared to matched CSSCD controls. The study subjects who had not been on regular simple transfusions prior to starting LTE had a mean serum ferritin of 681 ng/ml after LTE for an average duration of 63 months. LTE improves the growth of children with SCD without the risk of iron overload. © 2014 Wiley Periodicals, Inc.

Reliability of bounce drop jump parameters within elite male rugby players.

PubMed

Costley, Lisa; Wallace, Eric; Johnston, Michael; Kennedy, Rodney

2017-07-25

The aims of the study were to investigate the number of familiarisation sessions required to establish reliability of the bounce drop jump (BDJ) and subsequent reliability once familiarisation is achieved. Seventeen trained male athletes completed 4 BDJs in 4 separate testing sessions. Force-time data from a 20 cm BDJ was obtained using two force plates (ensuring ground contact < 250 ms). Subjects were instructed to 'jump for maximal height and minimal contact time' while the best and average of four jumps were compared. A series of performance variables were assessed in both eccentric and concentric phases including jump height, contact time, flight time, reactive strength index (RSI), peak power, rate of force development (RFD) and actual dropping height (ADH). Reliability was assessed using the intraclass correlation coefficient (ICC) and coefficient of variation (CV) while familiarisation was assessed using a repeated measures analysis of variance (ANOVA). The majority of DJ parameters exhibited excellent reliability with no systematic bias evident, while the average of 4 trials provided greater reliability. With the exception of vertical stiffness (CV: 12.0 %) and RFD (CV: 16.2 %) all variables demonstrated low within subject variation (CV range: 3.1 - 8.9 %). Relative reliability was very poor for ADH, with heights ranging from 14.87 - 29.85 cm. High levels of reliability can be obtained from the BDJ with the exception of vertical stiffness and RFD, however, extreme caution must be taken when comparing DJ results between individuals and squads due to large discrepancies between actual drop height and platform height.

In Situ Height and Width Estimation of Sorghum Plants from 2.5d Infrared Images

DOE PAGES

Baharav, Tavor; Bariya, Mohini; Zakhor, Avideh

2017-01-29

Plant phenotyping, or the measurement of plant traits such as stem width and plant height, is a critical step in the development and evaluation of higher yield biofuel crops. Phenotyping allows biologists to quantitatively estimate the biomass of plant varieties and therefore their potential for biofuel production. Manual phenotyping is costly, time-consuming, and errorprone, requiring a person to walk through the fields measuring individual plants with a tape measure and notebook. In this work we describe an alternative system consisting of an autonomous robot equipped with two infrared cameras that travels through fields, collecting 2.5D image data of sorghum plants.more » We develop novel image processing based algorithms to estimate plant height and stem width from the image data. Our proposed method has the advantage of working in situ using images of plants from only one side. This allows phenotypic data to be collected nondestructively throughout the growing cycle, providing biologists with valuable information on crop growth patterns. Our approach first estimates plant heights and stem widths from individual frames. It then uses tracking algorithms to refine these estimates across frames and avoid double counting the same plant in multiple frames. The result is a histogram of stem widths and plant heights for each plot of a particular genetically engineered sorghum variety. In-field testing and comparison with human collected ground truth data demonstrates that our system achieves 13% average absolute error for stem width estimation and 15% average absolute error for plant height estimation.« less

Small-scale open ocean currents have large effects on wind wave heights

NASA Astrophysics Data System (ADS)

Ardhuin, Fabrice; Gille, Sarah T.; Menemenlis, Dimitris; Rocha, Cesar B.; Rascle, Nicolas; Chapron, Bertrand; Gula, Jonathan; Molemaker, Jeroen

2017-06-01

Tidal currents and large-scale oceanic currents are known to modify ocean wave properties, causing extreme sea states that are a hazard to navigation. Recent advances in the understanding and modeling capability of open ocean currents have revealed the ubiquitous presence of eddies, fronts, and filaments at scales 10-100 km. Based on realistic numerical models, we show that these structures can be the main source of variability in significant wave heights at scales less than 200 km, including important variations down to 10 km. Model results are consistent with wave height variations along satellite altimeter tracks, resolved at scales larger than 50 km. The spectrum of significant wave heights is found to be of the order of 70>>2/>(g2>>2>) times the current spectrum, where >> is the spatially averaged significant wave height, >> is the energy-averaged period, and g is the gravity acceleration. This variability induced by currents has been largely overlooked in spite of its relevance for extreme wave heights and remote sensing.