Flight Crew Health Stabilization Program

NASA Technical Reports Server (NTRS)

Johnston, Smith L.

2010-01-01

This document establishes the policy and procedures for the HSP and is authorized through the Director, Johnson Space Center (JSC). This document delineates the medical operations requirements for the HSP. The HSP goals are accomplished through an awareness campaign and procedures such as limiting access to flight crewmembers, medical screening, and controlling flight crewmember activities. NASA's Human Space Flight Program uses strategic risk mitigation to achieve mission success while protecting crew health and safety. Infectious diseases can compromise crew health and mission success, especially in the immediate preflight period. The primary purpose of the Flight Crew Health Stabilization Program (HSP) is to mitigate the risk of occurrence of infectious disease among astronaut flight crews in the immediate preflight period. Infectious diseases are contracted through direct person-to-person contact, and through contact with infectious material in the environment. The HSP establishes several controls to minimize crew exposure to infectious agents. The HSP provides a quarantine environment for the crew that minimizes contact with potentially infectious material. The HSP also limits the number of individuals who come in close contact with the crew. The infection-carrying potential of these primary contacts (PCs) is minimized by educating them in ways to avoid infections and avoiding contact with the crew if they are or may be sick. The transmission of some infectious diseases can be greatly curtailed by vaccinations. PCs are strongly encouraged to maintain updated vaccinations.

Human influenza A (H5N1): a brief review and recommendations for travelers.

PubMed

Hurtado, Timothy R

2006-01-01

Although avian influenza A (H5N1) is common in birds worldwide, it has only recently led to disease in humans. Humans who are infected with the disease (referred to as human influenza A [H5N1]) have a greater than 50% mortality rate. Currently there has not been documented sustained human-to-human transmission; however, should the virus mutate and make this possible, the world could experience an influenza pandemic. Probable risk factors for infection include slaughtering, defeathering, and butchering fowl; close contact with wild birds or caged poultry; ingestion of undercooked poultry products; direct contact with surfaces contaminated with poultry feces; and close contact with infected humans. Possible risk factors include swimming in or ingesting water contaminated with bird feces or dead birds and the use of unprocessed poultry feces as fertilizer. Clinically, early human influenza A (H5N1) resembles typical influenza illnesses, with fever and a preponderance of lower respiratory tract symptoms. Often, patients develop rapidly progressive respiratory failure and require ventilatory support. Treatment is primarily supportive care with the addition of antiviral medications. Currently, travelers to countries with both human and avian influenza A (H5N1) have a low risk of developing the disease. There are no current recommended travel restrictions. Travelers are advised to avoid contact with all birds, especially poultry; avoid surfaces contaminated with poultry feces; and avoid undercooked poultry products. The use of prophylactic antiviral medications is not recommended.

Virtual social interactions in social anxiety--the impact of sex, gaze, and interpersonal distance.

PubMed

Wieser, Matthias J; Pauli, Paul; Grosseibl, Miriam; Molzow, Ina; Mühlberger, Andreas

2010-10-01

In social interactions, interpersonal distance between interaction partners plays an important role in determining the status of the relationship. Interpersonal distance is an important nonverbal behavior, and is used to regulate personal space in a complex interplay with other nonverbal behaviors such as eye gaze. In social anxiety, studies regarding the impact of interpersonal distance on within-situation avoidance behavior are so far rare. Thus the present study aimed to scrutinize the relationship between gaze direction, sex, interpersonal distance, and social anxiety in social interactions. Social interactions were modeled in a virtual-reality (VR) environment, where 20 low and 19 high socially anxious women were confronted with approaching male and female characters, who stopped in front of the participant, either some distance away or close to them, and displayed either a direct or an averted gaze. Gaze and head movements, as well as heart rate, were measured as indices of avoidance behavior and fear reactions. High socially anxious participants showed a complex pattern of avoidance behavior: when the avatar was standing farther away, high socially anxious women avoided gaze contact with male avatars showing a direct gaze. Furthermore, they showed avoidance behavior (backward head movements) in response to male avatars showing a direct gaze, regardless of the interpersonal distance. Overall, the current study proved that VR social interactions might be a very useful tool for investigating avoidance behavior of socially anxious individuals in highly controlled situations. This might also be the first step in using VR social interactions in clinical protocols for the therapy of social anxiety disorder.

Associating sex-biased and seasonal behaviour with contact patterns and transmission risk in Gopherus agassizii

USGS Publications Warehouse

Aiello, Christina M.; Esque, Todd; Nussear, K. E.; Emblidge, P. G.; Hudson, P. J.

2018-01-01

Interactions between wildlife hosts act as transmission routes for directly transmitted pathogens and vary in ways that affect transmission efficiency. Identifying drivers of contact variation can allow both contact inference and estimation of transmission dynamics despite limited data. In desert tortoises, mating strategy, burrow use and seasonal change influence numerous behaviours and likely shape contact patterns. In this study, we ask to what extent tortoise contact behaviour varies between sexes and seasons, and whether space or burrow-use data can be used to infer contact characteristics consistent with those recorded by proximity loggers. We identified sex and season-biased contact behaviour in both wild and captive populations indicative of female-female avoidance and seasonal male mate-seeking behaviour. Space and burrow-use patterns were informative, but did not always predict the extent of sex or seasonal biases on contact. We discuss the implications these findings have for transmission patterns and disease mitigation in tortoise populations.

High performance MoS2 TFT using graphene contact first process

NASA Astrophysics Data System (ADS)

Chang Chien, Chih-Shiang; Chang, Hsun-Ming; Lee, Wei-Ta; Tang, Ming-Ru; Wu, Chao-Hsin; Lee, Si-Chen

2017-08-01

An ohmic contact of graphene/MoS2 heterostructure is determined by using ultraviolet photoelectron spectroscopy (UPS). Since graphene shows a great potential to replace metal contact, a direct comparison of Cr/Au contact and graphene contact on the MoS2 thin film transistor (TFT) is made. Different from metal contacts, the work function of graphene can be modulated. As a result, the subthreshold swing can be improved. And when Vg

Thermal modelling and control of 130kw direct contact (salt/air) heat exchanger

NASA Astrophysics Data System (ADS)

Qureshi, Omer A.; Calvet, Nicolas; Armstrong, Peter R.

2017-06-01

This work investigates the transient response of a certain type of direct contact heat exchanger (DCHX) that consists of packing (Raschig Rings) to increase the surface area for effective heat transfer between molten salt and air. Molten salt from the hot tank enters the heat exchanger (HX) and exit after heating the air still in the molten form. Thermal capacitance of the HX, mainly due to packing and resident salt inside the HX, results in strong transient response. Pure delay from salt residence time may also impact transient response. Both phenomena have been modelled in this paper. A Proportional-Integral controller (PI control) performance has been evaluated to maintain the minimum salt temperature above avoid crystallization temperature of the salt.

Variable reluctance switch avoids contact corrosion and contact bounce

NASA Technical Reports Server (NTRS)

Watson, P. C.

1967-01-01

Variable reluctance switch avoids contact corrosion and bounce in a hostile environment. It consists of a wire-wound magnetic core and moveable bridge piece that alters the core flux pattern to produce an electrical output useful for switching control media.

High Ringxiety: Attachment Anxiety Predicts Experiences of Phantom Cell Phone Ringing.

PubMed

Kruger, Daniel J; Djerf, Jaikob M

2016-01-01

Mobile cell phone users have reported experiencing ringing and/or vibrations associated with incoming calls and messages, only to find that no call or message had actually registered. We believe this phenomenon can be understood as a human signal detection issue, with potentially important influences from psychological attributes. We hypothesized that individuals higher in attachment anxiety would report more frequent phantom cell phone experiences, whereas individuals higher in attachment avoidance would report less frequent experiences. If these experiences are primarily psychologically related to attributes of interpersonal relationships, associations with attachment style should be stronger than for general sensation seeking. We also predicted that certain contexts would interact with attachment style to increase or decrease the likelihood of experiencing phantom cell phone calls and messages. Attachment anxiety directly predicted the frequency of phantom ringing and notification experiences, whereas attachment avoidance and sensation seeking did not directly predict frequency. Attachment anxiety and attachment avoidance interacted with contextual factors (expectations for a call or message and concerned about an issue that one may be contacted about) in the expected directions for predicting phantom cell phone experiences.

Disease-avoidance processes and stigmatization: cues of substandard health arouse heightened discomfort with physical contact.

PubMed

Park, Justin H; van Leeuwen, Florian; Chochorelou, Ypapanti

2013-01-01

An evolutionary approach to stigmatization suggests that disease-avoidance processes contribute to some instances of social exclusion. Disease-avoidance processes are over-inclusive, targeting even non-threatening individuals who display cues of substandard health. We investigated whether such cues motivate avoidance of physical contact in particular. In Studies 1 and 2, targets with disease (e.g., leprosy) or atypical morphologies (e.g., amputated leg, obesity) were found to arouse differentially heightened discomfort with physical (versus nonphysical) contact, whereas a criminal target (stigmatized for disease-irrelevant reasons) was found to arouse elevated discomfort for both types of contact. Study 3 used a between-subjects design that eliminated the influence of extraneous factors. A diseased target was found to arouse differentially heightened discomfort with physical (versus nonphysical) contact, and to do so more strongly than any other type of target.

Abnormal social reward processing in autism as indexed by pupillary responses to happy faces

PubMed Central

2012-01-01

Background Individuals with Autism Spectrum Disorders (ASD) typically show impaired eye contact during social interactions. From a young age, they look less at faces than typically developing (TD) children and tend to avoid direct gaze. However, the reason for this behavior remains controversial; ASD children might avoid eye contact because they perceive the eyes as aversive or because they do not find social engagement through mutual gaze rewarding. Methods We monitored pupillary diameter as a measure of autonomic response in children with ASD (n = 20, mean age = 12.4) and TD controls (n = 18, mean age = 13.7) while they looked at faces displaying different emotions. Each face displayed happy, fearful, angry or neutral emotions with the gaze either directed to or averted from the subjects. Results Overall, children with ASD and TD controls showed similar pupillary responses; however, they differed significantly in their sensitivity to gaze direction for happy faces. Specifically, pupillary diameter increased among TD children when viewing happy faces with direct gaze as compared to those with averted gaze, whereas children with ASD did not show such sensitivity to gaze direction. We found no group differences in fixation that could explain the differential pupillary responses. There was no effect of gaze direction on pupil diameter for negative affect or neutral faces among either the TD or ASD group. Conclusions We interpret the increased pupillary diameter to happy faces with direct gaze in TD children to reflect the intrinsic reward value of a smiling face looking directly at an individual. The lack of this effect in children with ASD is consistent with the hypothesis that individuals with ASD may have reduced sensitivity to the reward value of social stimuli. PMID:22958650

Adsorption of flexible polymer chains on a surface: Effects of different solvent conditions

NASA Astrophysics Data System (ADS)

Martins, P. H. L.; Plascak, J. A.; Bachmann, M.

2018-05-01

Polymer chains undergoing a continuous adsorption-desorption transition are studied through extensive computer simulations. A three-dimensional self-avoiding walk lattice model of a polymer chain grafted onto a surface has been treated for different solvent conditions. We have used an advanced contact-density chain-growth algorithm, in which the density of contacts can be directly obtained. From this quantity, the order parameter and its fourth-order Binder cumulant are computed, as well as the corresponding critical exponents and the adsorption-desorption transition temperature. As the number of configurations with a given number of surface contacts and monomer-monomer contacts is independent of the temperature and solvent conditions, it can be easily applied to get results for different solvent parameter values without the need of any extra simulations. In analogy to continuous magnetic phase transitions, finite-size-scaling methods have been employed. Quite good results for the critical properties and phase diagram of very long single polymer chains have been obtained by properly taking into account the effects of corrections to scaling. The study covers all solvent effects, going from the limit of super-self-avoiding walks, characterized by effective monomer-monomer repulsion, to poor solvent conditions that enable the formation of compact polymer structures.

Modified Involute Helical Gears: Computerized Design, Simulation of Meshing, and Stress Analysis

NASA Technical Reports Server (NTRS)

Handschuh, Robert (Technical Monitor); Litvin, Faydor L.; Gonzalez-Perez, Ignacio; Carnevali, Luca; Kawasaki, Kazumasa; Fuentes-Aznar, Alfonso

2003-01-01

The computerized design, methods for generation, simulation of meshing, and enhanced stress analysis of modified involute helical gears is presented. The approaches proposed for modification of conventional involute helical gears are based on conjugation of double-crowned pinion with a conventional helical involute gear. Double-crowning of the pinion means deviation of cross-profile from an involute one and deviation in longitudinal direction from a helicoid surface. Using the method developed, the pinion-gear tooth surfaces are in point-contact, the bearing contact is localized and oriented longitudinally, and edge contact is avoided. Also, the influence of errors of aligment on the shift of bearing contact, vibration, and noise are reduced substantially. The theory developed is illustrated with numerical examples that confirm the advantages of the gear drives of the modified geometry in comparison with conventional helical involute gears.

Modified Involute Helical Gears: Computerized Design, Simulation of Meshing and Stress Analysis

NASA Technical Reports Server (NTRS)

2003-01-01

The computerized design, methods for generation, simulation of meshing, and enhanced stress analysis of modified involute helical gears is presented. The approaches proposed for modification of conventional involute helical gears are based on conjugation of double-crowned pinion with a conventional helical involute gear. Double-crowning of the pinion means deviation of cross-profile from an involute one and deviation in longitudinal direction from a helicoid surface. Using the method developed, the pinion-gear tooth surfaces are in point-contact, the bearing contact is localized and oriented longitudinally, and edge contact is avoided. Also, the influence of errors of alignment on the shift of bearing contact, vibration, and noise are reduced substantially. The theory developed is illustrated with numerical examples that confirm the advantages of the gear drives of the modified geometry in comparison with conventional helical involute gears.

Influence of Asymmetric Contact Form on Contact Resistance and Schottky Barrier, and Corresponding Applications of Diode.

PubMed

Zhao, Yudan; Xiao, Xiaoyang; Huo, Yujia; Wang, Yingcheng; Zhang, Tianfu; Jiang, Kaili; Wang, Jiaping; Fan, Shoushan; Li, Qunqing

2017-06-07

We have fabricated carbon nanotube and MoS 2 field-effect transistors with asymmetric contact forms of source-drain electrodes, from which we found the current directionality of the devices and different contact resistances under the two current directions. By designing various structures, we can conclude that the asymmetric electrical performance was caused by the difference in the effective Schottky barrier height (Φ SB ) caused by the different contact forms. A detailed temperature-dependent study was used to extract and compare the Φ SB for both contact forms of CNT and MoS 2 devices; we found that the Φ SB for the metal-on-semiconductor form was much lower than that of the semiconductor-on-metal form and is suitable for all p-type, n-type, or ambipolar semiconductors. This conclusion is meaningful with respect to the design and application of nanomaterial electronic devices. Additionally, using the difference in barrier height caused by the contact forms, we have also proposed and fabricated Schottky barrier diodes with a current ratio up to 10 4 ; rectifying circuits consisting of these diodes were able to work in a wide frequency range. This design avoided the use of complex chemical doping or heterojunction methods to achieve fundamental diodes that are relatively simple and use only a single material; these may be suitable for future application in nanoelectronic radio frequency or integrated circuits.

Bio-inspired vision based robot control using featureless estimations of time-to-contact.

PubMed

Zhang, Haijie; Zhao, Jianguo

2017-01-31

Marvelous vision based dynamic behaviors of insects and birds such as perching, landing, and obstacle avoidance have inspired scientists to propose the idea of time-to-contact, which is defined as the time for a moving observer to contact an object or surface if the current velocity is maintained. Since with only a vision sensor, time-to-contact can be directly estimated from consecutive images, it is widely used for a variety of robots to fulfill various tasks such as obstacle avoidance, docking, chasing, perching and landing. However, most of existing methods to estimate the time-to-contact need to extract and track features during the control process, which is time-consuming and cannot be applied to robots with limited computation power. In this paper, we adopt a featureless estimation method, extend this method to more general settings with angular velocities, and improve the estimation results using Kalman filtering. Further, we design an error based controller with gain scheduling strategy to control the motion of mobile robots. Experiments for both estimation and control are conducted using a customized mobile robot platform with low-cost embedded systems. Onboard experimental results demonstrate the effectiveness of the proposed approach, with the robot being controlled to successfully dock in front of a vertical wall. The estimation and control methods presented in this paper can be applied to computation-constrained miniature robots for agile locomotion such as landing, docking, or navigation.

Via Method for Lithography Free Contact and Preservation of 2D Materials.

PubMed

Telford, Evan J; Benyamini, Avishai; Rhodes, Daniel; Wang, Da; Jung, Younghun; Zangiabadi, Amirali; Watanabe, Kenji; Taniguchi, Takashi; Jia, Shuang; Barmak, Katayun; Pasupathy, Abhay N; Dean, Cory R; Hone, James

2018-02-14

Atomically thin 2D materials span the common components of electronic circuits as metals, semiconductors, and insulators, and can manifest correlated phases such as superconductivity, charge density waves, and magnetism. An ongoing challenge in the field is to incorporate these 2D materials into multilayer heterostructures with robust electrical contacts while preventing disorder and degradation. In particular, preserving and studying air-sensitive 2D materials has presented a significant challenge since they readily oxidize under atmospheric conditions. We report a new technique for contacting 2D materials, in which metal via contacts are integrated into flakes of insulating hexagonal boron nitride, and then placed onto the desired conducting 2D layer, avoiding direct lithographic patterning onto the 2D conductor. The metal contacts are planar with the bottom surface of the boron nitride and form robust contacts to multiple 2D materials. These structures protect air-sensitive 2D materials for months with no degradation in performance. This via contact technique will provide the capability to produce "atomic printed circuit boards" that can form the basis of more complex multilayer heterostructures.

(Bad) Feelings about Meeting Them? Episodic and Chronic Intergroup Emotions Associated with Positive and Negative Intergroup Contact As Predictors of Intergroup Behavior

PubMed Central

Kauff, Mathias; Asbrock, Frank; Wagner, Ulrich; Pettigrew, Thomas F.; Hewstone, Miles; Schäfer, Sarina J.; Christ, Oliver

2017-01-01

Based on two cross-sectional probability samples (Study 1: N = 1,382, Study 2: N = 1,587), we studied the interplay between positive and negative intergroup contact, different types of intergroup emotions (i.e., episodic intergroup emotions encountered during contact and more general chronic intergroup emotions), and outgroup behavior in the context of intergroup relations between non-immigrant Germans and foreigners living in Germany. In Study 1, we showed that positive and negative contact are related to specific episodic intergroup emotions (i.e., anger, fear and happiness). Results of Study 2 indicate an indirect effect of episodic intergroup emotions encountered during contact experiences on specific behavioral tendencies directed at outgroup members via more chronic situation-independent intergroup emotions. As expected, anger predicted approaching (discriminatory) behavioral tendencies (i.e., aggression) while fear predicted avoidance. The results extend the existing literature on intergroup contact and emotions by addressing positive and negative contact simultaneously and differentiating between situation-specific episodic and chronic intergroup emotions in predicting discriminatory behavioral tendencies. PMID:28900403

Stopping the Spread of Germs at Home, Work and School

MedlinePlus

... influenza viruses that research indicates will be most common during the upcoming season. There are several flu vaccine options for the 2017-2018 flu season . Good Health Habits Avoid close contact. Avoid close contact ...

Is Contact with Children Related to Legitimizing Beliefs Toward Sex with Children Among Men with Pedophilia?

PubMed

Geradt, Max; Jahnke, Sara; Heinz, Julia; Hoyer, Jürgen

2018-02-01

Among pedophilic men, social contact with children has been discussed as creating a risk situation for sexual abuse. Also, pedophilic men searching for such contact are seen as harboring more beliefs legitimizing sexual contact with children. However, social contact may also decrease false beliefs. We tested these competing views in an anonymous Internet survey with a non-forensic, non-clinical sample of 104 self-classified pedophilic men. Results showed that both increased social and physical contact were significantly linked to fewer legitimizing beliefs toward sex with children, even when controlling for past psychotherapy, educational level, social desirability, and age. Controlling for previous conviction for child sexual offenses reduced the effect for physical contact, but not for social contact. Exploratory analyses showed that either type of contact had no significant effect on total self-perceived risk of offending. However, pedophilic men with physical contact with children perceived a higher risk of more direct (i.e., child abuse) than indirect offenses (i.e., child pornography offenses) compared to pedophilic men without physical contact. Despite limitations of the correlational design and the only small to moderate effects, the results challenge the assumption that complete avoidance of contact with children is necessary for persons with pedophilia to reduce the risk of abusive behavior.

Systemic Contact Dermatitis.

PubMed

Aquino, Marcella; Rosner, Greg

2018-05-15

Systemic contact dermatitis (SCD) traditionally refers to a skin condition where an individual who is cutaneously sensitized to an allergen will subsequently react to that same allergen or a cross reacting allergen via a different route. It occurs to allergens including metals, medications, and foods. The exact pathophysiology underlying this disease remains unknown, although it appears to be mediated by type 4 hypersensitivity reactions and possibly type 3 hypersensitivity reactions. The p-I concept (pharmacologic interaction with immunoreceptors) hypothesized that drugs are able to bind directly to a T cell receptor without first being presented by MHC (major histocompatibility complex) molecules and without prior metabolism, which would help explain why SCD can be seen on first exposure to medications. Nomenclature remains a challenge as SCD can be subcategorized using terms such as ACDS (allergic contact dermatitis syndrome) and its four clinical stages, Baboon syndrome, and SDRIFE (symmetrical drug-related intertriginous and flexural exanthema), which share many overlapping features. Food allergens may be responsible for uncontrolled or persistent symptoms in patients with contact dermatitis who do not respond to topical avoidance. With medications, symptoms may be induced by topical application versus systemic administration. Patch testing (PT) may be beneficial in diagnosing SCD caused by metals and many topical medications including corticosteroids, antimicrobials (ampicillin, bacitracin, erythromycin, neomycin, nystatin), NSAIDs (diclofenac, ibuprofen), anesthetics, and antihistamines (chlorphenamine, piperazine). Current treatment options include topical steroids and oral antihistamines for symptom relief and dietary avoidance to causative foods or metals.

Assessing the Risk of Inadvertent Nuclear War Between India and Pakistan

DTIC Science & Technology

2002-12-01

stories/review.htm>. 5 avoided partly as a result of this. Hundreds of nuclear weapons tests were conducted, proving the technical capability of...sites in Cuba. The results of such an attack could have been disastrous, putting conventional systems in direct contact with nuclear systems, and... nuclear weapons and their delivery systems. Finally, India and Pakistan’s nuclear doctrines are compared. These comparisons yield important results

Gas-blowout control by water injection through relief wells: a theoretical analysis. [Injection of water into the formation through relief wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lehner, F.; Williamson, A.S.

1974-08-01

Koninklijke/Shell Exploratie en Produktie Laboratorium in The Netherlands suggests bringing a gas blowout under control by injecting water into the formation through relief wells. By avoiding direct contact between relief well and blowout well, this technique reduces the inflow of gas by creating sufficient back pressure in the formation itself. The mechanics of the technique are considered.

The Influence of Shyness on the Scanning of Own- and Other-Race Faces in Adults

PubMed Central

Wang, Qiandong; Hu, Chao; Short, Lindsey A.; Fu, Genyue

2012-01-01

The current study explored the relationship between shyness and face scanning patterns for own- and other-race faces in adults. Participants completed a shyness inventory and a face recognition task in which their eye movements were recorded by a Tobii 1750 eye tracker. We found that: (1) Participants’ shyness scores were negatively correlated with the fixation proportion on the eyes, regardless of the race of face they viewed. The shyer the participants were, the less time they spent fixating on the eye region; (2) High shyness participants tended to fixate significantly more than low shyness participants on the regions just below the eyes as if to avoid direct eye contact; (3) When participants were recognizing own-race faces, their shyness scores were positively correlated with the normalized criterion. The shyer they were, the more apt they were to judge the faces as novel, regardless of whether they were target or foil faces. The present results support an avoidance hypothesis of shyness, suggesting that shy individuals tend to avoid directly fixating on others’ eyes, regardless of face race. PMID:23284933

Nitrates and herbicides cause higher mortality than the traditional organic fertilizers on the grain beetle, Tenebrio molitor.

PubMed

Castilla, Aurora M; Dauwe, Tom; Mora, Isabel; Malone, Jim; Guitart, Raimon

2010-01-01

We examined experimentally whether fertilizers or herbicides commonly used by farmers affect mortality of the adult grain beetle Tenebrio molitor. After a period of 4 weeks in direct contact with all treatments, a higher percentage of mortality occurred in contact with nitrates than with pig manure or turkey litter. Herbicides (a mixture of glyphosate and 2,4-D: ) caused 100% mortality. Our results also indicate that more beetles escaped from the herbicides and nitrate treatments than from the others, suggesting some kind of behavioural avoidance of toxic environments. The traditional organic fertilizers appear to be less toxic than inorganic fertilizers for Tenebrio molitor.

Experimental investigation on the initial expansion stage of vacuum arc on cup-shaped TMF contacts

NASA Astrophysics Data System (ADS)

Wang, Ting; Xiu, Shixin; Liu, Zixi; Zhang, Yanzhe; Feng, Dingyu

2018-02-01

Arc behavior and measures to control it directly affect the properties of vacuum circuit breakers. Nowadays, transverse magnetic field (TMF) contacts are widely used for medium voltages. A magnetic field perpendicular to the current direction between the TMF contacts makes the arc move, transmitting its energy to the whole contact and avoiding excessive local ablation. Previous research on TMF arc behavior concentrated mainly on the arc movement and less on the initial stage (from arc ignition to an unstable arc column). A significant amount of experiment results suggest that there is a short period of arc stagnation after ignition. The duration of this arc stagnation and the arc characteristics during this stage affect the subsequent arc motion and even the breaking property of interrupters. The present study is of the arc characteristics in the initial stage. Experiments were carried out in a demountable vacuum chamber with cup-shaped TMF contacts. Using a high-speed camera, both single-point arc ignition mode and multiple-point arc ignition (MPAI) mode were observed. The experimental data show that the probability of MPAI mode occurring is related to the arc current. The influences of arc-ignition mode, arc current, and contact diameter on the initial expansion process were investigated. In addition, simulations were performed to analyze the multiple arc expansion process mechanically. Based on the experimental phenomena and simulation results, the mechanism of the arc expansion motion was analyzed.

Arabidopsis thaliana polyamine content is modified by the interaction with different Trichoderma species.

PubMed

Salazar-Badillo, Fatima Berenice; Sánchez-Rangel, Diana; Becerra-Flora, Alicia; López-Gómez, Miguel; Nieto-Jacobo, Fernanda; Mendoza-Mendoza, Artemio; Jiménez-Bremont, Juan Francisco

2015-10-01

Plants are associated with a wide range of microorganisms throughout their life cycle, and some interactions result on plant benefits. Trichoderma species are plant beneficial fungi that enhance plant growth and development, contribute to plant nutrition and induce defense responses. Nevertheless, the molecules involved in these beneficial effects still need to be identify. Polyamines are ubiquitous molecules implicated in plant growth and development, and in the establishment of plant microbe interactions. In this study, we assessed the polyamine profile in Arabidopsis plants during the interaction with Trichoderma virens and Trichoderma atroviride, using a system that allows direct plant-fungal contact or avoids their physical interaction (split system). The plantlets that grew in the split system exhibited higher biomass than the ones in direct contact with Trichoderma species. After 3 days of interaction, a significant decrease in Arabidopsis polyamine levels was observed in both systems (direct contact and split). After 5 days of interaction polyamine levels were increased. The highest levels were observed with T. atroviride (split system), and with T. virens (direct contact). The expression levels of Arabidopsis ADC1 and ADC2 genes during the interaction with the fungi were also assessed. We observed a time dependent regulation of ADC1 and ADC2 genes, which correlates with polyamine levels. Our data show an evident change in polyamine profile during Arabidopsis - Trichoderma interaction, accompanied by evident alterations in plant root architecture. Polyamines could be involved in the changes undergone by plant during the interaction with this beneficial fungus. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Gaze perception in social anxiety and social anxiety disorder

PubMed Central

Schulze, Lars; Renneberg, Babette; Lobmaier, Janek S.

2013-01-01

Clinical observations suggest abnormal gaze perception to be an important indicator of social anxiety disorder (SAD). Experimental research has yet paid relatively little attention to the study of gaze perception in SAD. In this article we first discuss gaze perception in healthy human beings before reviewing self-referential and threat-related biases of gaze perception in clinical and non-clinical socially anxious samples. Relative to controls, socially anxious individuals exhibit an enhanced self-directed perception of gaze directions and demonstrate a pronounced fear of direct eye contact, though findings are less consistent regarding the avoidance of mutual gaze in SAD. Prospects for future research and clinical implications are discussed. PMID:24379776

Intergroup Contact and Outgroup Humanization: Is the Causal Relationship Uni- or Bidirectional?

PubMed

Capozza, Dora; Di Bernardo, Gian Antonio; Falvo, Rossella

2017-01-01

The attribution of uniquely human characteristics to the outgroup may favor the search for contact with outgroup members and, vice versa, contact experiences may improve humanity attributions to the outgroup. To explore this bidirectional relationship, two studies were performed. In Study 1, humanity perceptions were manipulated using subliminal conditioning. Two experimental conditions were created. In the humanization condition, the unconditioned stimuli (US) were uniquely human words; in the dehumanization condition, the US were non-uniquely human and animal words. In both conditions, conditioned stimuli were typical outgroup faces. An approach/avoidance technique (the manikin task) was used to measure the willingness to have contact with outgroup members. Findings showed that in the humanization condition participants were faster in approaching than in avoiding outgroup members: closeness to the outgroup was preferred to distance. Latencies of approach and avoidance movements were not different in the dehumanization condition. In Study 2, contact was manipulated using the manikin task. One approach (contact) condition and two control conditions were created. The attribution of uniquely human traits to the outgroup was stronger in the contact than in the no-contact conditions. Furthermore, the effect of contact on humanity attributions was mediated by increased trust toward the outgroup. Thus, findings demonstrate the bidirectionality of the relationship between contact and humanity attributions. Practical implications of findings are discussed.

From Principal Component to Direct Coupling Analysis of Coevolution in Proteins: Low-Eigenvalue Modes are Needed for Structure Prediction

PubMed Central

Cocco, Simona; Monasson, Remi; Weigt, Martin

2013-01-01

Various approaches have explored the covariation of residues in multiple-sequence alignments of homologous proteins to extract functional and structural information. Among those are principal component analysis (PCA), which identifies the most correlated groups of residues, and direct coupling analysis (DCA), a global inference method based on the maximum entropy principle, which aims at predicting residue-residue contacts. In this paper, inspired by the statistical physics of disordered systems, we introduce the Hopfield-Potts model to naturally interpolate between these two approaches. The Hopfield-Potts model allows us to identify relevant ‘patterns’ of residues from the knowledge of the eigenmodes and eigenvalues of the residue-residue correlation matrix. We show how the computation of such statistical patterns makes it possible to accurately predict residue-residue contacts with a much smaller number of parameters than DCA. This dimensional reduction allows us to avoid overfitting and to extract contact information from multiple-sequence alignments of reduced size. In addition, we show that low-eigenvalue correlation modes, discarded by PCA, are important to recover structural information: the corresponding patterns are highly localized, that is, they are concentrated in few sites, which we find to be in close contact in the three-dimensional protein fold. PMID:23990764

Incorporating contact angles in the surface tension force with the ACES interface curvature scheme

NASA Astrophysics Data System (ADS)

Owkes, Mark

2017-11-01

In simulations of gas-liquid flows interacting with solid boundaries, the contact line dynamics effect the interface motion and flow field through the surface tension force. The surface tension force is directly proportional to the interface curvature and the problem of accurately imposing a contact angle must be incorporated into the interface curvature calculation. Many commonly used algorithms to compute interface curvatures (e.g., height function method) require extrapolating the interface, with defined contact angle, into the solid to allow for the calculation of a curvature near a wall. Extrapolating can be an ill-posed problem, especially in three-dimensions or when multiple contact lines are near each other. We have developed an accurate methodology to compute interface curvatures that allows for contact angles to be easily incorporated while avoiding extrapolation and the associated challenges. The method, known as Adjustable Curvature Evaluation Scale (ACES), leverages a least squares fit of a polynomial to points computed on the volume-of-fluid (VOF) representation of the gas-liquid interface. The method is tested by simulating canonical test cases and then applied to simulate the injection and motion of water droplets in a channel (relevant to PEM fuel cells).

[Direct electric conduction glove for laparoscopic surgical instruments. Preliminary results of a prototype].

PubMed

Gentilli, Sergio; Morgandoa, Andrea; Velardocchia, Mauro; Pessione, Silvia; Pizzorno, Chiara

2007-01-01

The authors present their prototype of a system for electrical conduction in direct contact with laparoscopic tools, devised, designed and produced by them at the Politecnico di Torino Department of Mechanical Engineering. The system consists of a two-sided plate, one side being a non-conducting adhesive surface to stick to the surgical glove and the other a thin, flexible conductor shell. The authors used the instrument with surgical tools with metal handles during 4 laparoscopic procedures. Nowadays the method commonly used to electrify laparoscopic tools is by using a wire plugged to a fixed conducting point on the instrument. The prototype described here was devised and produced to avoid some of the awkwardness encountered during the numerous manoeuvres required to connect and disconnect the wire at the time of surgical intervention. This device permits the direct transfer (by contact) of electrical energy from the wire to surgical tools. The advantage is greater rapidity in changing surgical tools, with the possibility of immediately obtaining an electrified instrument in the surgeon's hand.

Avoiding Cross-Contact

MedlinePlus

... View more examples of cross-contact > Talking to Restaurant Personnel about Cross-Contact It is important to ... meals. Do not be nervous about calling a restaurant you would like to dine at. The chef ...

Can Gaze Avoidance Explain Why Individuals with Asperger's Syndrome Can't Recognise Emotions from Facial Expressions?

ERIC Educational Resources Information Center

Sawyer, Alyssa C. P.; Williamson, Paul; Young, Robyn L.

2012-01-01

Research has shown that individuals with Autism Spectrum Disorders (ASD) have difficulties recognising emotions from facial expressions. Since eye contact is important for accurate emotion recognition, and individuals with ASD tend to avoid eye contact, this tendency for gaze aversion has been proposed as an explanation for the emotion recognition…

21 CFR 347.52 - Labeling of astringent drug products.

Code of Federal Regulations, 2010 CFR

2010-04-01

... use only”. (ii) The labeling states “When using this product [bullet] avoid contact with eyes. If... affected area. Dry pencil after use.” (3) For products containing witch hazel identified in § 347.12(c... may be omitted. The second warning in § 347.52(c)(1) may state: “avoid contact with eyes”. The warning...

The "Eye Avoidance" Hypothesis of Autism Face Processing.

PubMed

Tanaka, James W; Sung, Andrew

2016-05-01

Although a growing body of research indicates that children with autism spectrum disorder (ASD) exhibit selective deficits in their ability to recognize facial identities and expressions, the source of their face impairment is, as yet, undetermined. In this paper, we consider three possible accounts of the autism face deficit: (1) the holistic hypothesis, (2) the local perceptual bias hypothesis and (3) the eye avoidance hypothesis. A review of the literature indicates that contrary to the holistic hypothesis, there is little evidence to suggest that individuals with autism do perceive faces holistically. The local perceptual bias account also fails to explain the selective advantage that ASD individuals demonstrate for objects and their selective disadvantage for faces. The eye avoidance hypothesis provides a plausible explanation of face recognition deficits where individuals with ASD avoid the eye region because it is perceived as socially threatening. Direct eye contact elicits a increased physiological response as indicated by heightened skin conductance and amygdala activity. For individuals with autism, avoiding the eyes is an adaptive strategy, however, this approach interferes with the ability to process facial cues of identity, expressions and intentions, exacerbating the social challenges for persons with ASD.

Nickel Allergy

MedlinePlus

... Nickel allergy is a common cause of allergic contact dermatitis — an itchy rash that appears where your skin ... need to avoid contact. Symptoms An allergic reaction (contact dermatitis) usually begins within hours to days after exposure ...

Kite-flying: a unique but dangerous mode of electrical injury in children.

PubMed

Tiwari, V K; Sharma, D

1999-09-01

A retrospective study was conducted to evaluate the cause of a sudden rise in number of pediatric admissions with electrical injuries at our centre during the year 1998. In evaluating the cause, six out of twelve admissions were found to be related to kite-flying which is a popular sport during the months of June, July, August and September. In two out of six cases current travelled directly through the string of the kite. In two others, flame burns occured following ignition of clothing. Another patient had contact with wire through a metal rod. In the last case, arcing pulled the hand of the patient leading to direct contact with wire. The average burns size was approximately 31% body surface area (BSA), with all patients having burns over the palmar aspect of at least one hand. No patient required amputation for the injuries. In this article, attention has been focussed on the various modes of electrical injuries associated with kite-flying and some measures have been advised to avoid such accidents.

Patterns of cosmetic contact allergy.

PubMed

Castanedo-Tardan, Mari Paz; Zug, Kathryn A

2009-07-01

Certain patterns of dermatitis, such as those affecting the face, eyelids, lips, and neck, should raise the suspicion of a cosmetic-related contact allergy. Patch testing with a broad screening series, supplemented by a patient's own personal care products, should be considered when evaluating patients with suspected cosmetic dermatitis. Once the offending allergen is identified, an avoidance regimen should be established to avoid further exposure.

An ultra-bright white LED based non-contact skin cancer imaging system with polarization control

NASA Astrophysics Data System (ADS)

Günther, A.; Basu, C.; Roth, B.; Meinhardt-Wollweber, M.

2013-06-01

Early detection and excision of melanoma skin cancer is crucial for a successful therapy. Dermoscopy in direct contact with the skin is routinely used for inspection, but screening is time consuming for high-risk patients with a large number of nevi. Features like symmetry, border, color and most importantly changes like growth or depigmentation of a nevus may indicate malignancy. We present a non-contact remote imaging system for human melanocytic nevi with homogenous illumination by an ultra-bright white LED. The advantage compared to established dermoscopy systems requiring direct skin contact is that deformation of raised nevi is avoided and full-body scans of the patients may time-efficiently be obtained while they are in a lying, comfortable position. This will ultimately allow for automated screening in the future. In addition, calibration of true color rendering, which is essential for distinguishing between benign and malignant lesions and to ensure reproducibility and comparison between individual check-ups in order to follow nevi evolution is implemented as well as suppression of specular highlights on the skin surface by integration of polarizing filters. Important features of the system which will be crucial for future integration into automated systems are the possibility to record images without artifacts in combination with short exposure times which both reduce image blurring caused by patient motion.

Submarine Combat Systems Engineering Project Capstone Project

DTIC Science & Technology

2011-06-06

sonar , imaging, Electronic Surveillance (ES) and communications. These sensors passively detect contacts, which emit... passive sensors is included. A Search Detect Identify Track Decide Engage Assess 3 contact can be sensed by the system as either surface or... Detect Track Avoid Search Detect Identify Track Search Engage Assess Detect Track Avoid Search • SONAR •Imagery •TC • SONAR • SONAR •EW •Imagery •ESM

Technological Advances in Deep Brain Stimulation.

PubMed

Ughratdar, Ismail; Samuel, Michael; Ashkan, Keyoumars

2015-01-01

Functional and stereotactic neurosurgery has always been regarded as a subspecialty based on and driven by technological advances. However until recently, the fundamentals of deep brain stimulation (DBS) hardware and software design had largely remained stagnant since its inception almost three decades ago. Recent improved understanding of disease processes in movement disorders as well clinician and patient demands has resulted in new avenues of development for DBS technology. This review describes new advances both related to hardware and software for neuromodulation. New electrode designs with segmented contacts now enable sophisticated shaping and sculpting of the field of stimulation, potentially allowing multi-target stimulation and avoidance of side effects. To avoid lengthy programming sessions utilising multiple lead contacts, new user-friendly software allows for computational modelling and individualised directed programming. Therapy delivery is being improved with the next generation of smaller profile, longer-lasting, re-chargeable implantable pulse generators (IPGs). These include IPGs capable of delivering constant current stimulation or personalised closed-loop adaptive stimulation. Post-implantation Magnetic Resonance Imaging (MRI) has long been an issue which has been partially overcome with 'MRI conditional devices' and has enabled verification of DBS lead location. Surgical technique is considering a shift from frame-based to frameless stereotaxy or greater role for robot assisted implantation. The challenge for these contemporary techniques however, will be in demonstrating equivalent safety and accuracy to conventional methods. We also discuss potential future direction utilising wireless technology allowing for miniaturisation of hardware.

Rashes: The Itchy Truth

MedlinePlus

... while it's healing. Allergic contact dermatitis is a rash caused by contact with an allergen (say: AL-ur-jun). An ... when you'll be going outside. For allergic dermatitis or irritant contact dermatitis, try to avoid that substance. If you ...

Efficient local behavioral-change strategies to reduce the spread of epidemics in networks

NASA Astrophysics Data System (ADS)

Bu, Yilei; Gregory, Steve; Mills, Harriet L.

2013-10-01

It has recently become established that the spread of infectious diseases between humans is affected not only by the pathogen itself but also by changes in behavior as the population becomes aware of the epidemic, for example, social distancing. It is also well known that community structure (the existence of relatively densely connected groups of vertices) in contact networks influences the spread of disease. We propose a set of local strategies for social distancing, based on community structure, that can be employed in the event of an epidemic to reduce the epidemic size. Unlike most social distancing methods, ours do not require individuals to know the disease state (infected or susceptible, etc.) of others, and we do not make the unrealistic assumption that the structure of the entire contact network is known. Instead, the recommended behavior change is based only on an individual's local view of the network. Each individual avoids contact with a fraction of his/her contacts, using knowledge of his/her local network to decide which contacts should be avoided. If the behavior change occurs only when an individual becomes ill or aware of the disease, these strategies can substantially reduce epidemic size with a relatively small cost, measured by the number of contacts avoided.

Optimal geometry toward uniform current density electrodes

NASA Astrophysics Data System (ADS)

Song, Yizhuang; Lee, Eunjung; Woo, Eung Je; Seo, Jin Keun

2011-07-01

Electrodes are commonly used to inject current into the human body in various biomedical applications such as functional electrical stimulation, defibrillation, electrosurgery, RF ablation, impedance imaging, and so on. When a highly conducting electrode makes direct contact with biological tissues, the induced current density has strong singularity along the periphery of the electrode, which may cause painful sensation or burn. Especially in impedance imaging methods such as the magnetic resonance electrical impedance tomography, we should avoid such singularity since more uniform current density underneath a current-injection electrode is desirable. In this paper, we study an optimal geometry of a recessed electrode to produce a well-distributed current density on the contact area under the electrode. We investigate the geometry of the electrode surface to minimize the edge singularity and produce nearly uniform current density on the contact area. We propose a mathematical framework for the uniform current density electrode and its optimal geometry. The theoretical results are supported by numerical simulations.

Interfacial thermal resistance and thermal rectification in carbon nanotube film-copper systems.

PubMed

Duan, Zheng; Liu, Danyang; Zhang, Guang; Li, Qingwei; Liu, Changhong; Fan, Shoushan

2017-03-02

Thermal rectification occurring at interfaces is an important research area, which contains deep fundamental physics and has extensive application prospects. In general, the measurement of interfacial thermal rectification is based on measuring interfacial thermal resistance (ITR). However, ITRs measured via conventional methods cannot avoid extra thermal resistance asymmetry due to the contact between the sample and the thermometer. In this study, we employed a non-contact infrared thermal imager to monitor the temperature of super-aligned carbon nanotube (CNT) films and obtain the ITRs between the CNT films and copper. The ITRs along the CNT-copper direction and the reverse direction are in the ranges of 2.2-3.6 cm 2 K W -1 and 9.6-11.9 cm 2 K W -1 , respectively. The obvious difference in the ITRs of the two directions shows a significant thermal rectification effect, and the rectifying coefficient ranges between 0.57 and 0.68. The remarkable rectification factor is extremely promising for the manufacture of thermal transistors with a copper/CNT/copper structure and further thermal logic devices. Moreover, our method could be extended to other 2-dimensional materials, such as graphene and MoS 2 , for further explorations.

Ground reaction forces of Olympic and World Championship race walkers.

PubMed

Hanley, Brian; Bissas, Athanassios

2016-01-01

Race walking is an Olympic event where no visible loss of contact should occur and the knee must be straightened until midstance. The purpose of this study was to analyse ground reaction forces of world-class race walkers and associate them with key spatiotemporal variables. Nineteen athletes race walked along an indoor track and made contact with two force plates (1000 Hz) while being filmed using high-speed videography (100 Hz). Race walking speed was correlated with flight time (r = .46, p = .049) and flight distance (r = .69, p = .001). The knee's movement from hyperextension to flexion during late stance meant the vertical push-off force that followed midstance was smaller than the earlier loading peak (p < .001), resulting in a flattened profile. Athletes with narrower stride widths experienced reduced peak braking forces (r = .49, p = .046), peak propulsive forces (r = .54, p = .027), peak medial forces (r = .63, p = .007) and peak vertical push-off forces (r = .60, p = .011). Lower fluctuations in speed during stance were associated with higher stride frequencies (r = .69, p = .001), and highlighted the importance of avoiding too much braking in early stance. The flattened trajectory and consequential decrease in vertical propulsion might help the race walker avoid visible loss of contact (although non-visible flight times were useful in increasing stride length), while a narrow stride width was important in reducing peak forces in all three directions and could improve movement efficiency.

Distrust As a Disease Avoidance Strategy: Individual Differences in Disgust Sensitivity Regulate Generalized Social Trust.

PubMed

Aarøe, Lene; Osmundsen, Mathias; Petersen, Michael Bang

2016-01-01

Throughout human evolutionary history, cooperative contact with others has been fundamental for human survival. At the same time, social contact has been a source of threats. In this article, we focus on one particular viable threat, communicable disease, and investigate how motivations to avoid pathogens influence people's propensity to interact and cooperate with others, as measured by individual differences in generalized social trust. While extant studies on pathogen avoidance have argued that such motivations should prompt people to avoid interactions with outgroups specifically, we argue that these motivations should prompt people to avoid others more broadly. Empirically, we utilize two convenience samples and a large nationally representative sample of US citizens to demonstrate the existence of a robust and replicable effect of individual differences in pathogen disgust sensitivity on generalized social trust. We furthermore compare the effects of pathogen disgust sensitivity on generalized social trust and outgroup prejudice and explore whether generalized social trust to some extent constitutes a pathway between pathogen avoidance motivations and prejudice.

Distrust As a Disease Avoidance Strategy: Individual Differences in Disgust Sensitivity Regulate Generalized Social Trust

PubMed Central

Aarøe, Lene; Osmundsen, Mathias; Petersen, Michael Bang

2016-01-01

Throughout human evolutionary history, cooperative contact with others has been fundamental for human survival. At the same time, social contact has been a source of threats. In this article, we focus on one particular viable threat, communicable disease, and investigate how motivations to avoid pathogens influence people's propensity to interact and cooperate with others, as measured by individual differences in generalized social trust. While extant studies on pathogen avoidance have argued that such motivations should prompt people to avoid interactions with outgroups specifically, we argue that these motivations should prompt people to avoid others more broadly. Empirically, we utilize two convenience samples and a large nationally representative sample of US citizens to demonstrate the existence of a robust and replicable effect of individual differences in pathogen disgust sensitivity on generalized social trust. We furthermore compare the effects of pathogen disgust sensitivity on generalized social trust and outgroup prejudice and explore whether generalized social trust to some extent constitutes a pathway between pathogen avoidance motivations and prejudice. PMID:27516744

The geological and petrological studies of the subduction boundaries and suggestion for the geological future work in Japan　- How to avoid ultra-mega-earthquakes -

NASA Astrophysics Data System (ADS)

Ishii, T.

2015-12-01

The Pacific plate is surrounded by circum-Pacific active margin, along which volcanic and seismic activities are very high. Ultra-Mega-Earthquakes (=UMEs, M>9.0) are occasionally observed along the margin, where sedimentary rocks of subducting slaves contact with the accreted sedimentary rocks of subducted slaves. But, those UME have never been occured along western Pacific islandarc-trench system including Izu-Ogasawara (=Bonin)-Mariana-Yap-Palau-Philippine-Tonga-Kermadec Trenches. I assume that the geological and petrological characteristics of the subduction boundaries are very important to understand those different seismic activities. Along the above mentioned trench inner wall, especially in the southern Mariana, mantle peridotites are widely distributed. Subducting slave contacts directly with the olivine dominant mantle peridotites of subducted slave, serpentinite layer can be deposited easily under hydrous oceanic sub-bottom environment and very slippery subduction boundaries are left along the subduction zone.On the other hand, those geological evidences give us some ideas on how to avoid UMEs in the Japanese Islands along Japan Trench and Nankai Trough in future. We will be able to change artificially from normal subduction boundaries with asperity zone into slippery subduction boundaries with serpentine layer, by means of serpentine mud injection toward the subduction boundaries interior by combining the following improved drilling technologies A and B. (A) Deep Sea Drilling Vessel CHIKYU has a drilling ability to reach subduction boundary with asperity zone in the Nankai Trough. (B) Advanced drilling technology in the shale gas industry is tremendous, that is, after one vertical deep drilling, horizontal drilling towards several direction are performed, then shale gas is collected by hydraulic fracturing method. I hope that, after several generations, our posterity will be able to avoid UMEs by continuous serpentine mud injection.

Methotrexate use in allergic contact dermatitis: a retrospective study.

PubMed

Patel, Ashaki; Burns, Erin; Burkemper, Nicole M

2018-03-01

Methotrexate, a folate antimetabolite, is used to treat atopic dermatitis and psoriasis. Although methotrexate's therapeutic efficacy has been noted in the literature, there are few data on the efficacy of methotrexate treatment for allergic contact dermatitis. To evaluate the efficacy and tolerability of methotrexate in treating allergic contact dermatitis at a single institution, and also to assess methotrexate efficacy in patients with chronic, unavoidable allergen exposure. We performed a retrospective chart review of 32 patients diagnosed with allergic contact dermatitis by positive patch test reactions, and who received treatment with methotrexate from November 2010 to November 2014. Demographic and treatment-associated data were collected from electronic medical records. Ten patients were identified as allergen non-avoiders secondary to their occupation, and were subgrouped as such. Seventy-eight per cent (25/32) of patients showed either a partial or a complete response. Methotrexate had a comparable efficacy rate in the allergen non-avoiders subset, at 10 of 10. Of the 32 patients, 23% (5/22) had complete clearance of their dermatitis, and 1/10 of allergen non-avoiders had complete clearance of their dermatitis. Methotrexate is a well-tolerated and effective treatment for allergic contact dermatitis, and shows comparable efficacy to immunomodulatory agents such as cyclosporine and azathioprine, with robust efficacy despite persistent allergen exposure in patients with allergic contact dermatitis. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Direct Laser Writing of Nanophotonic Structures on Contact Lenses.

PubMed

AlQattan, Bader; Yetisen, Ali K; Butt, Haider

2018-04-24

Contact lenses are ubiquitous biomedical devices used for vision correction and cosmetic purposes. Their application as quantitative analytical devices is highly promising for point-of-care diagnostics. However, it is a challenge to integrate nanoscale features into commercial contact lenses for application in low-cost biosensors. A neodymium-doped yttrium aluminum garnet (Nd:YAG) laser (1064 nm, 3 ns pulse, 240 mJ) in holographic interference patterning mode was utilized to produce optical nanostructures over the surface of a hydrogel contact lens. One-dimensional (925 nm) and two-dimensional (925 nm × 925 nm) nanostructures were produced on contact lenses and analyzed by spectroscopy and angle-resolve measurements. The holographic properties of these nanostructures were tested in ambient moisture, fully hydrated, and artificial tear conditions. The measurements showed a rapid tuning of optical diffraction from these nanostructures from 41 to 48°. The nanostructures were patterned near the edges of the contact lens to avoid any interference and obstruction to the human vision. The formation of 2D nanostructures on lenses increased the diffraction efficiency by more than 10%. The versatility of the holographic laser ablation method was demonstrated by producing four different 2D nanopattern geometries on contact lenses. Hydrophobicity of the contact lens was characterized by contact angle measurements, which increased from 59.0° at pristine condition to 62.5° at post-nanofabrication. The holographic nanostructures on the contact lens were used to sense the concentration of Na + ions. Artificial tear solution was used to simulate the conditions in dry eye syndrome, and nanostructures on the contact lenses were used to detect the electrolyte concentration changes (±47 mmol L -1 ). Nanopatterns on a contact lens may be used to sense other ocular diseases in early stages at point-of-care settings.

Clinical impact of an open-irrigated radiofrequency catheter with direct force measurement on atrial fibrillation ablation.

PubMed

Martinek, Martin; Lemes, Christine; Sigmund, Elisabeth; Derndorfer, Michael; Aichinger, Josef; Winter, Siegmund; Nesser, Hans-Joachim; Pürerfellner, Helmut

2012-11-01

Electrode-tissue contact is crucial for adequate lesion formation in radiofrequency catheter ablation (RFCA). We assessed the impact of direct catheter force measurement on acute procedural parameters during RFCA of atrial fibrillation (AF). Fifty consecutive patients (28 male) with paroxysmal AF who underwent their first procedure of circumferential pulmonary vein (PV) isolation (PVI) were assigned to either RFCA using (1) a standard 3.5-mm open-irrigated-tip catheter or (2) a catheter with contact force measurement capabilities. Using the endpoint of PVI with entry and exit block, acute procedural parameters were assessed. Procedural data showed a remarkable decline in ablation time (radiofrequency time needed for PVI) from 50.5 ± 15.9 to 39.0 ± 11.0 minutes (P = 0.007) with a reduction in overall procedure duration from 185 ± 46 to 154 ± 39 minutes (P = 0.022). In parallel, the total energy delivered could be significantly reduced from 70,926 ± 19,470 to 58,511 ± 14,655 Ws (P = 0.019). The number of acute PV reconnections declined from 36% to 12% (P = 0.095). The use of contact force sensing technology is able to significantly reduce ablation and procedure times in PVI. In addition, energy delivery is substantially reduced by avoiding radiofrequency ablation in positions with insufficient surface contact. Procedural efficacy and safety of this new feature have to be evaluated in larger cohorts. ©2012, The Authors. Journal compilation ©2012 Wiley Periodicals, Inc.

A New Apparatus for Measuring the Temperature at Machine Parts Rotating at High Speeds

NASA Technical Reports Server (NTRS)

Gnam, E.

1945-01-01

After a brief survey of the available methods for measuring the temperatures of machine parts at high speed, in particular turbine blades and rotors, an apparatus is described which is constructed on the principle of induction. Transmission of the measuring current by sliding contacts therefore is avoided. Up-to-date experiments show that it is possible to give the apparatus a high degree of sensitivity and accuracy. In comparison with sliding contact types, the present apparatus shows the important advantage that it operates for any length of time without wear, and that the contact difficulties, particularly occurring at high sliding speeds,are avoided.

Direct detection signatures of self-interacting dark matter with a light mediator

DOE PAGES

Nobile, Eugenio Del; Kaplinghat, Manoj; Yu, Hai-Bo

2015-10-27

Self-interacting dark matter (SIDM) is a simple and well-motivated scenario that could explain long-standing puzzles in structure formation on small scales. If the required self-interaction arises through a light mediator (with mass ~ 10 MeV) in the dark sector, this new particle must be unstable to avoid overclosing the universe. The decay of the light mediator could happen due to a weak coupling of the hidden and visible sectors, providing new signatures for direct detection experiments. The SIDM nuclear recoil spectrum is more peaked towards low energies compared to the usual case of contact interactions, because the mediator mass ismore » comparable to the momentum transfer of nuclear recoils. We show that the SIDM signal could be distinguished from that of DM particles with contact interactions by considering the time-average energy spectrum in experiments employing different target materials, or the average and modulated spectra in a single experiment. Using current limits from LUX and SuperCDMS, we also derive strong bounds on the mixing parameter between hidden and visible sector.« less

A computational parametric study on edge loading in ceramic-on-ceramic total hip joint replacements.

PubMed

Liu, Feng; Feng, Li; Wang, Junyuan

2018-07-01

Edge loading in ceramic-on-ceramic total hip joint replacement is an adverse condition that occurs as the result of a direct contact between the head and the cup rim. It has been associated with translational mismatch in the centres of rotation of the cup and head, and found to cause severe wear and early failure of the implants. Edge loading has been considered in particular in relation to dynamic separation of the cup and head centres during a gait cycle. Research has been carried out both experimentally and computationally to understand the mechanism including the influence of bearing component positioning on the occurrence and severity of edge loading. However, it is experimentally difficult to measure both the load magnitude and duration of edge loading as it occurs as a short impact within the tight space of hip joints. Computationally, a dynamic contact model, for example, developed using the MSC ADAMS software for a multi-body dynamics simulation can be particularly useful for calculating the loads and characterising the edge loading. The aim of the present study was to further develop the computational model, and improve the predictions of contact force and the understanding of mechanism in order to provide guidance on design and surgical factors to avoid or to reduce edge loading and wear. The results have shown that edge loading can be avoided for a low range of translational mismatch in the centres of rotation of the cup and head during gait at the level of approximately 1.0 mm for a cup at 45° inclination, keeping a correct cup inclination at 45° is important to reduce the edge loading severity, and edge loading can be avoided for a certain range of translational mismatch of the cup and head centres with an increased swing phase load. Copyright © 2018 Elsevier Ltd. All rights reserved.

Rubber dam isolation--key to success in diastema closure technique with direct composite resin.

PubMed

Barros de Campos, Paulo Ricardo; Maia, Rodrigo Rocha; Rodrigues de Menezes, Livia; Barbosa, Isabel Ferreira; Carneiro da Cunha, Amanda; da Silveira Pereira, Gisele Damiana

2015-01-01

The use of direct composite resin for diastema closure has technique advantages, including that the restorative procedure can be carried out in one appointment at a reasonable cost and without the removal of sound tooth structure. The use of a rubber dam for closing diastemas with composite resin is of paramount importance as it prevents moisture contamination and ensures increased gingival retraction compared to other techniques. This provides better access to the cervical area of the tooth, facilitating proper placement of resin to recreate the natural anatomical contours and contact point. Thus, there is a more natural adaptation of the restoration to the gingival tissue, avoiding a space between the papilla and the restored tooth. To illustrate the advantages of this technique, two diastema closure cases are presented using direct composite resin with rubber dam isolation.

Ebola virus disease

MedlinePlus

... body fluids of infected animals Contact with infected bats Ebola does NOT spread through: Air Water Food ... who has died from Ebola. Avoid contact with bats and nonhuman primates or blood, fluids, and raw ...

Reactions of Oklahoma City bombing survivors to media coverage of the September 11, 2001, attacks.

PubMed

Pfefferbaum, Betty; Nitiéma, Pascal; Pfefferbaum, Rose L; Houston, J Brian; Tucker, Phebe; Jeon-Slaughter, Haekyung; North, Carol S

2016-02-01

This study explored the effects of media coverage of a terrorist incident in individuals remote from the location of a major attack who had directly experienced a prior terrorist incident. Directly-exposed survivors of the 1995 Oklahoma City bombing, initially studied six months after the incident, and indirectly-affected Oklahoma City community residents were assessed two to seven months after the September 11, 2001, attacks. Survivors were assessed for a diagnosis of bombing-related posttraumatic stress disorder (PTSD) at index and follow up, and emotional reactions and September 11 media behavior were assessed in all participants. Among the three investigated forms of media (television, radio, and newspaper), only television viewing was associated with 9/11-related posttraumatic stress reactions. Exposure to the Oklahoma City bombing was associated with greater arousal in relation to the September 11 attacks, and among survivors, having developed bombing-related PTSD was associated with higher scores on all three September 11 posttraumatic stress response clusters (intrusion, avoidance, and arousal). Although time spent watching television coverage of the September 11 attacks and fear-related discontinuation of media contact were not associated with Oklahoma City bombing exposure, discontinuing September 11 media contact due to fear was associated with avoidance/numbing in the full sample and in the analysis restricted to the bombing survivors. Surviving a prior terrorist incident and developing PTSD in relation to that incident may predispose individuals to adverse reactions to media coverage of a future terrorist attack. Copyright © 2015 Elsevier Inc. All rights reserved.

Novel patterning of CdS / CdTe thin film with back contacts for photovoltaic application

NASA Astrophysics Data System (ADS)

Ilango, Murugaiya Sridar; Ramasesha, Sheela K.

2018-04-01

The heterostructure of patterned CdS / CdTe thin films with back contact have been devised with electron beam lithography and fabricated using sputter deposition technique. The metallic contacts for n-CdS and p-CdTe are patterned such that both are placed at the bottom of the cell. This avoids losses due to contact shading and increases absorption in the window layer. Patterning of the device surface helps in increasing the junction area which can modulate the absorption of more number of photons due to total internal reflection. Computing the surface area between a planar and a patterned device has revealed 133% increase in the junction area. The physical and optical properties of the sputter-deposited CdS / CdTe layers are also presented. J- V characteristics of the solar cell showed the fill factor to be 25.9%, open circuit voltage to be 17 mV and short-circuit current density to be 113.68 A/m2. The increase in surface area is directly related to the increase in the short circuit current of the photovoltaic cell, which is observed from the results of simulated model in Atlas / Silvaco.

Strategies for obstacle avoidance during walking in the cat.

PubMed

Chu, Kevin M I; Seto, Sandy H; Beloozerova, Irina N; Marlinski, Vladimir

2017-08-01

Avoiding obstacles is essential for successful navigation through complex environments. This study aimed to clarify what strategies are used by a typical quadruped, the cat, to avoid obstacles during walking. Four cats walked along a corridor 2.5 m long and 25 or 15 cm wide. Obstacles, small round objects 2.5 cm in diameter and 1 cm in height, were placed on the floor in various locations. Movements of the paw were recorded with a motion capture and analysis system (Visualeyez, PTI). During walking in the wide corridor, cats' preferred strategy for avoiding a single obstacle was circumvention, during which the stride direction changed while stride duration and swing-to-stride duration ratio were preserved. Another strategy, stepping over the obstacle, was used during walking in the narrow corridor, when lateral deviations of walking trajectory were restricted. Stepping over the obstacle involved changes in two consecutive strides. The stride preceding the obstacle was shortened, and swing-to-stride ratio was reduced. The obstacle was negotiated in the next stride of increased height and normal duration and swing-to-stride ratio. During walking on a surface with multiple obstacles, both strategies were used. To avoid contact with the obstacle, cats placed the paw away from the object at a distance roughly equal to the diameter of the paw. During obstacle avoidance cats prefer to alter muscle activities without altering the locomotor rhythm. We hypothesize that a choice of the strategy for obstacle avoidance is determined by minimizing the complexity of neuro-motor processes required to achieve the behavioral goal. NEW & NOTEWORTHY In a study of feline locomotor behavior we found that the preferred strategy to avoid a small obstacle is circumvention. During circumvention, stride direction changes but length and temporal structure are preserved. Another strategy, stepping over the obstacle, is used in narrow walkways. During overstepping, two strides adjust. A stride preceding the obstacle decreases in length and duration. The following stride negotiating the obstacle increases in height while retaining normal temporal structure and nearly normal length. Copyright © 2017 the American Physiological Society.

Comparison of choose-a-movie and approach-avoidance paradigms to measure social motivation.

PubMed

Dubey, Indu; Ropar, Danielle; Hamilton, Antonia

2018-01-01

Social motivation is a subjective state which is rather difficult to quantify. It has sometimes been conceptualised as "behavioural effort" to seek social contact. Two paradigms: approach-avoidance (AA) and choose a movie (CAM), based on the same conceptualisation, have been used to measure social motivation in people with and without autism. However, in absence of a direct comparison, it is hard to know which of these paradigms has higher sensitivity in estimating preference for social over non-social stimuli. Here we compare these two tasks for their utility in (1) evaluating social seeking in typical people and (2) identifying the influence of autistic traits on social motivation. Our results suggest that CAM reveals a clear preference for social stimuli over non-social in typical adults but AA fails to do so. Also, social seeking measured with CAM but not AA has a negative relationship between autistic traits.

National survey of Ebola-related knowledge, attitudes and practices before the outbreak peak in Sierra Leone: August 2014

PubMed Central

Jalloh, Mohamed F; Sengeh, Paul; Monasch, Roeland; Jalloh, Mohammad B; DeLuca, Nickolas; Dyson, Meredith; Golfa, Sheku; Sakurai, Yukiko; Conteh, Lansana; Sesay, Samuel; Brown, Vance; Li, Wenshu; Mermin, Jonathan; Bunnell, Rebecca

2017-01-01

Background The 2014–2015 Ebola epidemic in West Africa was the largest ever to occur. In the early phases, little was known about public knowledge, attitudes and practices (KAP) relating to Ebola virus disease (Ebola). Data were needed to develop evidence-driven strategies to address gaps in knowledge and practice. Methods In August 2014, we conducted interviews with 1413 randomly selected respondents from 9 out of 14 districts in Sierra Leone using multistage cluster sampling. Where suitable, Ebola-related KAP questions were adapted from other internationally validated questionnaires related to infectious diseases. Results All respondents were aware of Ebola. When asked unprompted, 60% of respondents could correctly cite fever, diarrhoea and vomiting as signs/symptoms of Ebola. A majority of respondents knew that avoiding infected blood and bodily fluids (87%) and contact with an infected corpse (85%) could prevent Ebola. However, there were also widespread misconceptions such as the belief that Ebola can be prevented by washing with salt and hot water (41%). Almost everyone interviewed (95%) expressed at least one discriminatory attitude towards Ebola survivors. Unprompted, self-reported actions taken to avoid Ebola infection included handwashing with soap (66%) and avoiding physical contact with patients with suspected Ebola (40%). Conclusion Three months into the 2014 Ebola outbreak in Sierra Leone, our findings suggest there was high awareness of the disease but misconceptions and discriminatory attitudes toward survivors remained common. These findings directly informed the development of a national social mobilisation strategy and demonstrated the importance of KAP assessment early in an epidemic. PMID:29259820

Epidemics on adaptive networks with geometric constraints

NASA Astrophysics Data System (ADS)

Shaw, Leah; Schwartz, Ira

2008-03-01

When a population is faced with an epidemic outbreak, individuals may modify their social behavior to avoid exposure to the disease. Recent work has considered models in which the contact network is rewired dynamically so that susceptibles avoid contact with infectives. We consider extensions in which the rewiring is subject to constraints that preserve key properties of the social network structure. Constraining to a fixed degree distribution destroys previously observed bistable behavior. The most effective rewiring strategy is found to depend on the spreading rate.

Cryptic effects of habitat declines: coral-associated fishes avoid coral-seaweed interactions due to visual and chemical cues.

PubMed

Brooker, Rohan M; Brandl, Simon J; Dixson, Danielle L

2016-01-04

Seaweed-dominated coral reefs are becoming increasingly common as environmental conditions shift away from those required by corals and toward those ideal for rampant seaweed growth. How coral-associated organisms respond to seaweed will not only impact their fate following environmental change but potentially also the trajectories of the coral communities on which they rely. However, behavioral responses by coral-associated organisms to seaweeds are poorly understood. This study examined interactions between a guild of obligate and opportunistic coral-feeding butterflyfishes (Chaetodontidae) and scleractinian corals to determine whether fishes continue to interact with corals in contact with seaweed or if they are avoided. Under natural conditions, all species interacted almost exclusively with seaweed-free corals. In a controlled patch reef experiment, fishes avoided corals in physical contact with seaweed, irrespective of dietary preferences. When visual seaweed cues were removed, butterflyfish continued to avoid corals that had been in contact with the allelopathic Galaxaura filamentosa, suggesting that chemical cues produced by coral-seaweed interactions are repellent. These findings suggest that, due to deleterious visual and chemical cues produced by coral-seaweed interactions, coral-associated organisms may struggle to locate resources as seaweed-free corals decline in abundance.

The Eyes Are the Windows to the Mind: Direct Eye Gaze Triggers the Ascription of Others' Minds.

PubMed

Khalid, Saara; Deska, Jason C; Hugenberg, Kurt

2016-12-01

Eye gaze is a potent source of social information with direct eye gaze signaling the desire to approach and averted eye gaze signaling avoidance. In the current work, we proposed that eye gaze signals whether or not to impute minds into others. Across four studies, we manipulated targets' eye gaze (i.e., direct vs. averted eye gaze) and measured explicit mind ascriptions (Study 1a, Study 1b, and Study 2) and beliefs about the likelihood of targets having mind (Study 3). In all four studies, we find novel evidence that the ascription of sophisticated humanlike minds to others is signaled by the display of direct eye gaze relative to averted eye gaze. Moreover, we provide evidence suggesting that this differential mentalization is due, at least in part, to beliefs that direct gaze targets are more likely to instigate social interaction. In short, eye contact triggers mind perception. © 2016 by the Society for Personality and Social Psychology, Inc.

Pet avoidance in allergy cases: Is it possible to implement it?

PubMed

Sánchez, Jorge; Díez, Susana; Cardona, Ricardo

2015-01-01

Among allergic patients, pet avoidance is commonly recommended. It is difficult for patients to accomplish this because of their emotional attachment to the pets, and its effectiveness is controversial. To explore the applicability and effectiveness of pet avoidance measures among sensitized patients. We evaluated 288 patients with asthma, rhinitis, conjunctivitis and/or dermatitis using skin prick test to measure their sensitization to cats, dogs and other animals to which they were exposed. Exposure to animals was evaluated in each patient (pets at home, frequent indirect exposure or no exposure). In those patients sensitized to animals some avoidance measures, such as removing pets from home and preventing indirect exposure, were recommended. On the following two appointments, we evaluated patients' fulfillment of these recommendations. Sensitization to cats, dogs and birds was high (9%, 48%, 14%, respectively), as well as direct and indirect exposure (30%, 46%, 24%, respectively). Most patients denied contact with other animals (horses, hamsters, rabbits or cows), and sensitization to them was low. During the follow-up of patients sensitized to their pets at home (n=50), most of them refused to remove them from their house due to emotional attachment, and only two followed this recommendation. High exposure to animals could explain the frequency of sensitization to pets in this population. However, emotional attachment and prevalent indirect exposure to animals among sensitized patients make avoidance recommendations impractical or impossible to achieve.

Difficulties in avoiding exposure to allergens in cosmetics.

PubMed

Noiesen, Eline; Munk, Martin D; Larsen, Kristian; Johansen, Jeanne Duus; Agner, Tove

2007-08-01

The aim of the study is to describe the ability of patients with allergic contact dermatitis to avoid exposure to allergens in cosmetics. The study is a questionnaire survey among 382 patients with contact allergy to preservatives and fragrances, included from 3 dermatological clinics. The questionnaire included questions about the level of difficulty in reading labels of ingredients on cosmetics and about patients' strategies to avoid substances they were allergic to. It also included questions about eczema severity as well as about educational level. 46% of the patients found it difficult or extremely difficult to read the ingredient labelling of cosmetics, and this finding was significantly related to low educational level. Patients allergic to formaldehyde and methyldibromo glutaronitrile experienced the worst difficulties, while patients with fragrance allergy found ingredient label reading easier than patients with preservative allergy. Reading of ingredient labels is a major problem for patients with contact allergy to allergens in consumer products. It is a general problem for all patients and not restricted to a small group with multiple allergies.

Quantification of surface displacements and electromechanical phenomena via dynamic atomic force microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balke, Nina; Jesse, Stephen; Yu, Pu

Detection of dynamic surface displacements associated with local changes in material strain provides access to a number of phenomena and material properties. Contact resonance-enhanced methods of atomic force microscopy (AFM) have been shown capable of detecting ~1–3 pm-level surface displacements, an approach used in techniques such as piezoresponse force microscopy, atomic force acoustic microscopy, and ultrasonic force microscopy. Here, based on an analytical model of AFM cantilever vibrations, we demonstrate a guideline to quantify surface displacements with high accuracy by taking into account the cantilever shape at the first resonant contact mode, depending on the tip–sample contact stiffness. The approachmore » has been experimentally verified and further developed for piezoresponse force microscopy (PFM) using well-defined ferroelectric materials. These results open up a way to accurate and precise measurements of surface displacement as well as piezoelectric constants at the pm-scale with nanometer spatial resolution and will allow avoiding erroneous data interpretations and measurement artifacts. Furthermore, this analysis is directly applicable to all cantilever-resonance-based scanning probe microscopy (SPM) techniques.« less

Quantification of surface displacements and electromechanical phenomena via dynamic atomic force microscopy

DOE PAGES

Balke, Nina; Jesse, Stephen; Yu, Pu; ...

2016-09-15

Detection of dynamic surface displacements associated with local changes in material strain provides access to a number of phenomena and material properties. Contact resonance-enhanced methods of atomic force microscopy (AFM) have been shown capable of detecting ~1–3 pm-level surface displacements, an approach used in techniques such as piezoresponse force microscopy, atomic force acoustic microscopy, and ultrasonic force microscopy. Here, based on an analytical model of AFM cantilever vibrations, we demonstrate a guideline to quantify surface displacements with high accuracy by taking into account the cantilever shape at the first resonant contact mode, depending on the tip–sample contact stiffness. The approachmore » has been experimentally verified and further developed for piezoresponse force microscopy (PFM) using well-defined ferroelectric materials. These results open up a way to accurate and precise measurements of surface displacement as well as piezoelectric constants at the pm-scale with nanometer spatial resolution and will allow avoiding erroneous data interpretations and measurement artifacts. Furthermore, this analysis is directly applicable to all cantilever-resonance-based scanning probe microscopy (SPM) techniques.« less

Avoiding chromium transport from stainless steel interconnects into contact layers and oxygen electrodes in intermediate temperature solid oxide electrolysis stacks

NASA Astrophysics Data System (ADS)

Schlupp, Meike V. F.; Kim, Ji Woo; Brevet, Aude; Rado, Cyril; Couturier, Karine; Vogt, Ulrich F.; Lefebvre-Joud, Florence; Züttel, Andreas

2014-12-01

We investigated the ability of (La0.8Sr0.2)(Mn0.5Co0.5)O3-δ (LSMC) and La(Ni0.6Fe0.4)O3-δ (LNF) contact coatings to avoid the transport of Cr from steel interconnects to solid oxide electrolysis electrodes, especially to the anode. The transport of chromium from commercial Crofer 22 APU (ThyssenKrupp) and K41X (AISI441, Aperam Isbergues) steels through LSMC and LNF contact coatings into adjacent (La0.8Sr0.2)MnO3-δ (LSM) oxygen electrodes was investigated in an oxygen atmosphere at 700 °C. Chromium concentrations of up to 4 atom% were detected in the contact coatings after thermal treatments for 3000 h, which also lead to the presence of chromium in adjacent LSM electrodes. Introduction of a dense (Co,Mn)3O4 coating between steel and contact coating was necessary to prevent the diffusion of chromium into contact coatings and electrodes and should lead to extended stack performance and lifetime.

Understanding HIV Stigma among University Students: Judgment, Blame, and Interpersonal Avoidance

ERIC Educational Resources Information Center

Watson, Victoria J.; Guagnano, Gregory; Davis, Shannon N.

2012-01-01

Using vignettes, levels of HIV stigma among university students (n = 971) were examined to identify the likelihood of judging and blaming or avoiding personal and intimate contact with an HIV-positive individual. Reactions to the vignettes showed judgment and blame and intimate avoidance were higher when HIV was contracted through unprotected sex.…

The “eye avoidance” hypothesis of autism face processing

PubMed Central

Tanaka, James W.; Sung, Andrew

2013-01-01

Although a growing body of research indicates that children with autism spectrum disorder (ASD) exhibit selective deficits in their ability to recognize facial identities and expressions, the source of their face impairment is, as yet, undetermined. In this paper, we consider three possible accounts of the autism face deficit: 1) the holistic hypothesis, 2) the local perceptual bias hypothesis and 3) the eye avoidance hypothesis. A review of the literature indicates that contrary to the holistic hypothesis, there is little evidence to suggest that individuals with autism do not perceive faces holistically. The local perceptual bias account also fails to explain the selective advantage that ASD individuals demonstrate for objects and their selective disadvantage for faces. The eye avoidance hypothesis provides a plausible explanation of face recognition deficits where individuals with ASD avoid the eye region because it is perceived as socially threatening. Direct eye contact elicits a heightened physiological response as indicated by heightened skin conductance and increased amgydala activity. For individuals with autism, avoiding the eyes is an adaptive strategy, however, this approach interferes with the ability to process facial cues of identity, expressions and intentions, The “eye avoidance” strategy has negative effects on the ability to decode facial information about identity, expression, and intentions, exacerbating the social challenges for persons with ASD. PMID:24150885

Can gaze avoidance explain why individuals with Asperger's syndrome can't recognise emotions from facial expressions?

PubMed

Sawyer, Alyssa C P; Williamson, Paul; Young, Robyn L

2012-04-01

Research has shown that individuals with Autism Spectrum Disorders (ASD) have difficulties recognising emotions from facial expressions. Since eye contact is important for accurate emotion recognition, and individuals with ASD tend to avoid eye contact, this tendency for gaze aversion has been proposed as an explanation for the emotion recognition deficit. This explanation was investigated using a newly developed emotion and mental state recognition task. Individuals with Asperger's Syndrome were less accurate at recognising emotions and mental states, but did not show evidence of gaze avoidance compared to individuals without Asperger's Syndrome. This suggests that the way individuals with Asperger's Syndrome look at faces cannot account for the difficulty they have recognising expressions.

Zoonotic Hookworm FAQs

MedlinePlus

... when exposed skin comes in contact with contaminated soil or sand. The larvae in the contaminated soil or sand will burrow into the skin and ... measures to avoid skin contact with sand or soil will prevent infection with zoonotic hookworms. Travelers to ...

Reproductive development of male goat kids reared with or without permanent contact with adult females until 10 months of age.

PubMed

Lacuesta, L; Orihuela, A; Ungerfeld, R

2015-01-01

Adult male ruminants that were reared in contact with females display greater sexual behavior than those reared in single male groups. The aim of the experiment was to compare the reproductive development of prepubertal male kids reared with or without direct permanent contact with adult females until they were 10 months old. Seventeen Saanen male kids were maintained in two groups until 44 weeks of age: kids reared in permanent direct contact with four adult goats (group FEM, N = 8) and kids that remained isolated from females (group ISO, N = 9). All goats in the FEM group became pregnant approximately when bucks attained 28 weeks of age. Scrotal circumference and testosterone concentration were measured, and semen was obtained by electroejaculation to avoid female contact in the ISO group. Scrotal circumference was greater in FEM kids at 12 and 14 weeks of age (P < 0.0001) and testosterone when they were 20 and 22 weeks old (P < 0.0001). Testosterone concentration was greater in ISO kids from 28 to 44 weeks of age. All semen characteristics increased with age (P < 0.0001). Individual motility was greater in FEM kids than that in ISO kids at 15 and 17 weeks (P < 0.005); mass motility was greater in ISO than that in FEM kids at 32 weeks (P < 0.05); total number of spermatozoa/ejaculate was greater in ISO kids at 30, 32, and 40 weeks and in FEM kids at 43 weeks (P < 0.005); total number of motile spermatozoa was greater in ISO kids at 32 and 40 weeks, whereas at 43 weeks, it was greater in FEM kids (P < 0.005). It was concluded that permanent contact with adult goats had transient and short-time positive effects in male kids' reproductive traits during prepubertal development. However, positive effects stopped after goats used as stimulus became pregnant. Copyright © 2015 Elsevier Inc. All rights reserved.

Nonverbal Behavior of Young Abused and Neglected Children.

ERIC Educational Resources Information Center

Hecht, Michael; And Others

1986-01-01

Investigated whether abused and neglected children differ from other children in their nonverbal attachment and communicative behavior. Found that in comparison (1) abused children avoided contact and interaction and (2) abused females exhibited more avoidance than males. (PD)

PSD Camera Based Position and Posture Control of Redundant Robot Considering Contact Motion

NASA Astrophysics Data System (ADS)

Oda, Naoki; Kotani, Kentaro

The paper describes a position and posture controller design based on the absolute position by external PSD vision sensor for redundant robot manipulator. The redundancy enables a potential capability to avoid obstacle while continuing given end-effector jobs under contact with middle link of manipulator. Under contact motion, the deformation due to joint torsion obtained by comparing internal and external position sensor, is actively suppressed by internal/external position hybrid controller. The selection matrix of hybrid loop is given by the function of the deformation. And the detected deformation is also utilized in the compliant motion controller for passive obstacle avoidance. The validity of the proposed method is verified by several experimental results of 3link planar redundant manipulator.

Preference for social contact versus environmental enrichment in male laboratory mice.

PubMed

Van Loo, P L P; Van de Weerd, H A; Van Zutphen, L F M; Baumans, V

2004-04-01

Due to their aggressive nature, male mice are less frequently used than female mice in biomedical research. When aggressive males are being used, individual housing is common practice. The question arises whether this is an acceptable housing for a social species. The present study was designed to gain more insight into the nature of inter-male social contact and into the potential of a form of environmental enrichment (nesting material) to compensate for the lack of social contact. In a series of tests, we analysed whether male mice of different ages preferred to spend time (1) near a familiar cage mate versus an empty cage, or (2) near to a familiar cage mate versus direct contact with nesting material (tissues). Dwelling time in each of the test cages and sleeping sites was recorded, as was the behaviour of the test mice. Results indicated that when other conditions were similar, male mice preferred to sleep in close proximity to their familiar cage mate. Furthermore, the need to engage in active social behaviour increased with age. Tissues were used to a large extent for sleeping and sleep-related behaviour. It is concluded that single housing in order to avoid aggression between male mice is a solution with evident negative consequences for the animals. When individual housing is inevitable due to excessive aggressive behaviour, the presence of nesting material could partly compensate for the deprivation of social contact.

76 FR 23490 - Aluminum tris (O

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-27

... code 112). Food manufacturing (NAICS code 311). Pesticide manufacturing (NAICS code 32532). This... used to avoid contamination of food, feed, or food-contact/feed-contact surfaces. Compliance with the... are an agricultural producer, food manufacturer, or pesticide manufacturer. Potentially affected...

Pre-Teenage Children's Strategies for Avoiding Situations in Which They Might Be Exposed to Drugs

ERIC Educational Resources Information Center

McIntosh, James; MacDonald, Fiona; McKeganey, Neil

2005-01-01

This paper explores the ways in which pre-teenage children try to avoid coming into contact with illegal drugs and then examines the factors and circumstances that facilitate or impede their efforts to achieve this. Their main strategy of avoiding certain groups or individuals was complicated by the fluid nature of young people's social groups and…

Gaze direction differentially affects avoidance tendencies to happy and angry faces in socially anxious individuals.

PubMed

Roelofs, Karin; Putman, Peter; Schouten, Sonja; Lange, Wolf-Gero; Volman, Inge; Rinck, Mike

2010-04-01

Increasing evidence indicates that eye gaze direction affects the processing of emotional faces in anxious individuals. However, the effects of eye gaze direction on the behavioral responses elicited by emotional faces, such as avoidance behavior, remain largely unexplored. We administered an Approach-Avoidance Task (AAT) in high (HSA) and low socially anxious (LSA) individuals. All participants responded to photographs of angry, happy and neutral faces (presented with direct and averted gaze), by either pushing a joystick away from them (avoidance) or pulling it towards them (approach). Compared to LSA, HSA were faster in avoiding than approaching angry faces. Most crucially, this avoidance tendency was only present when the perceived anger was directed towards the subject (direct gaze) and not when the gaze of the face-stimulus was averted. In contrast, HSA individuals tended to avoid happy faces irrespectively of gaze direction. Neutral faces elicited no approach-avoidance tendencies. Thus avoidance of angry faces in social anxiety as measured by AA-tasks reflects avoidance of subject-directed anger and not of negative stimuli in general. In addition, although both anger and joy are considered to reflect approach-related emotions, gaze direction did not affect HSA's avoidance of happy faces, suggesting differential mechanisms affecting responses to happy and angry faces in social anxiety. 2009 Elsevier Ltd. All rights reserved.

An infrared-driven flexible pyroelectric generator for non-contact energy harvester

NASA Astrophysics Data System (ADS)

Zhao, Tingting; Jiang, Weitao; Liu, Hongzhong; Niu, Dong; Li, Xin; Liu, Weihua; Li, Xuan; Chen, Bangdao; Shi, Yongsheng; Yin, Lei; Lu, Bingheng

2016-04-01

In recent years, energy harvesting technologies, which can scavenge many kinds of energies from our living environment to power micro/nanodevices, have attracted increasing attention. However, remote energy transmission, flexibility and electric waveform controllability remain the key challenges for wireless power supply by an energy harvester. In this paper, we design a new infrared-driven non-contact pyroelectric generator for harvesting heat energy, which avoids direct contact between the pyroelectric generator and heat source and realizes remote energy transfer exploiting the photothermal and penetrability of infrared light. The output voltage (under the input impedance of 100 MOhm) and short-circuit current of the pyroelectric generator consisting of a CNT/PVDF/CNT layer (20 mm × 5 mm × 100 μm) can be as large as 1.2 V and 9 nA, respectively, under a 1.45 W cm-2 near-infrared laser (808 nm). We also demonstrate the means by which the pyroelectric generator can modulate square waveforms with controllable periods through irradiation frequency, which is essential for signal sources and medical stimulators. The overshoot of square waveforms are in a range of 9.0%-13.1% with a rise time of 120 ms. The prepared pyroelectric generator can light a liquid crystal display (LCD) in a vacuum chamber from outside. This work paves the way for non-contact energy harvesting for some particular occasions where near-field energy control is not available.In recent years, energy harvesting technologies, which can scavenge many kinds of energies from our living environment to power micro/nanodevices, have attracted increasing attention. However, remote energy transmission, flexibility and electric waveform controllability remain the key challenges for wireless power supply by an energy harvester. In this paper, we design a new infrared-driven non-contact pyroelectric generator for harvesting heat energy, which avoids direct contact between the pyroelectric generator and heat source and realizes remote energy transfer exploiting the photothermal and penetrability of infrared light. The output voltage (under the input impedance of 100 MOhm) and short-circuit current of the pyroelectric generator consisting of a CNT/PVDF/CNT layer (20 mm × 5 mm × 100 μm) can be as large as 1.2 V and 9 nA, respectively, under a 1.45 W cm-2 near-infrared laser (808 nm). We also demonstrate the means by which the pyroelectric generator can modulate square waveforms with controllable periods through irradiation frequency, which is essential for signal sources and medical stimulators. The overshoot of square waveforms are in a range of 9.0%-13.1% with a rise time of 120 ms. The prepared pyroelectric generator can light a liquid crystal display (LCD) in a vacuum chamber from outside. This work paves the way for non-contact energy harvesting for some particular occasions where near-field energy control is not available. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr09290f

Cryptic effects of habitat declines: coral-associated fishes avoid coral-seaweed interactions due to visual and chemical cues

PubMed Central

Brooker, Rohan M.; Brandl, Simon J.; Dixson, Danielle L.

2016-01-01

Seaweed-dominated coral reefs are becoming increasingly common as environmental conditions shift away from those required by corals and toward those ideal for rampant seaweed growth. How coral-associated organisms respond to seaweed will not only impact their fate following environmental change but potentially also the trajectories of the coral communities on which they rely. However, behavioral responses by coral-associated organisms to seaweeds are poorly understood. This study examined interactions between a guild of obligate and opportunistic coral-feeding butterflyfishes (Chaetodontidae) and scleractinian corals to determine whether fishes continue to interact with corals in contact with seaweed or if they are avoided. Under natural conditions, all species interacted almost exclusively with seaweed-free corals. In a controlled patch reef experiment, fishes avoided corals in physical contact with seaweed, irrespective of dietary preferences. When visual seaweed cues were removed, butterflyfish continued to avoid corals that had been in contact with the allelopathic Galaxaura filamentosa, suggesting that chemical cues produced by coral-seaweed interactions are repellent. These findings suggest that, due to deleterious visual and chemical cues produced by coral-seaweed interactions, coral-associated organisms may struggle to locate resources as seaweed-free corals decline in abundance. PMID:26725835

Voice Technology Design Guides for Navy Training Systems.

DTIC Science & Technology

1983-03-01

34 LSO acknowledges (AUTOIMANUAL/ pilot meatball Coupled as acquisition. appropriate) "Paddles Contact" LSO assuming control from CCA. (continued) 68... meatball to avoid ball to avoid settling slope if not corrected. settling below glide- below glideslope. slope. "Don’t climb"- If not corrected air...Check sink rate and Check sink rate and meat- "Don’t go high." craft will climb above meatball to avoid ball to avoid climbing optimum glideslope

Closed-loop feedback control for microfluidic systems through automated capacitive fluid height sensing.

PubMed

Soenksen, L R; Kassis, T; Noh, M; Griffith, L G; Trumper, D L

2018-03-13

Precise fluid height sensing in open-channel microfluidics has long been a desirable feature for a wide range of applications. However, performing accurate measurements of the fluid level in small-scale reservoirs (<1 mL) has proven to be an elusive goal, especially if direct fluid-sensor contact needs to be avoided. In particular, gravity-driven systems used in several microfluidic applications to establish pressure gradients and impose flow remain open-loop and largely unmonitored due to these sensing limitations. Here we present an optimized self-shielded coplanar capacitive sensor design and automated control system to provide submillimeter fluid-height resolution (∼250 μm) and control of small-scale open reservoirs without the need for direct fluid contact. Results from testing and validation of our optimized sensor and system also suggest that accurate fluid height information can be used to robustly characterize, calibrate and dynamically control a range of microfluidic systems with complex pumping mechanisms, even in cell culture conditions. Capacitive sensing technology provides a scalable and cost-effective way to enable continuous monitoring and closed-loop feedback control of fluid volumes in small-scale gravity-dominated wells in a variety of microfluidic applications.

[News on occupational contact dermatitis].

PubMed

Crépy, Marie-Noëlle; Bensefa-Colas, Lynda

2014-03-01

Contact dermatitis--irritant contact dermatitis, allergic contact dermatitis and protein contact dermatitis--are the most common occupational skin diseases, most often localized to the hands. Contact urticaria is rarer The main occupational irritants are wet work, detergents and disinfectants, cutting oils, and solvents. The main occupational allergens are rubber additives, metals (chromium, nickel, cobalt), plastics (epoxy resins, acrylic), biocides and plants. Diagnosis is based on clinical examination, medical history and allergy testing. For a number of irritating or sensitizing agents, irritant or allergic dermatitis can be notified as occupational diseases. The two main prevention measures are reducing skin contact with irritants and complete avoidance of skin contact with offending allergens.

Seasonality and pathogen transmission in pastoral cattle contact networks.

PubMed

VanderWaal, Kimberly; Gilbertson, Marie; Okanga, Sharon; Allan, Brian F; Craft, Meggan E

2017-12-01

Capturing heterogeneity in contact patterns in animal populations is essential for understanding the spread of infectious diseases. In contrast to other regions of the world in which livestock movement networks are integral to pathogen prevention and control policies, contact networks are understudied in pastoral regions of Africa due to the challenge of measuring contact among mobile herds of cattle whose movements are driven by access to resources. Furthermore, the extent to which seasonal changes in the distribution of water and resources impacts the structure of contact networks in cattle is uncertain. Contact networks may be more conducive to pathogen spread in the dry season due to congregation at limited water sources. Alternatively, less abundant forage may result in decreased pathogen transmission due to competitive avoidance among herds, as measured by reduced contact rates. Here, we use GPS technology to concurrently track 49 free-roaming cattle herds within a semi-arid region of Kenya, and use these data to characterize seasonal contact networks and model the spread of a highly infectious pathogen. This work provides the first empirical data on the local contact network structure of mobile herds based on quantifiable contact events. The contact network demonstrated high levels of interconnectivity. An increase in contacts near to water resources in the dry season resulted in networks with both higher contact rates and higher potential for pathogen spread than in the wet season. Simulated disease outbreaks were also larger in the dry season. Results support the hypothesis that limited water resources enhance connectivity and transmission within contact networks, as opposed to reducing connectivity as a result of competitive avoidance. These results cast light on the impact of seasonal heterogeneity in resource availability on predicting pathogen transmission dynamics, which has implications for other free-ranging wild and domestic populations.

The German Version of the Gaze Anxiety Rating Scale (GARS): Reliability and Validity

PubMed Central

Domes, Gregor; Marx, Lisa; Spenthof, Ines; Heinrichs, Markus

2016-01-01

Objective Fear of eye gaze and avoidance of eye contact are core features of social anxiety disorders (SAD). To measure self-reported fear and avoidance of eye gaze, the Gaze Anxiety Rating Scale (GARS) has been developed and validated in recent years in its English version. The main objectives of the present study were to psychometrically evaluate the German translation of the GARS concerning its reliability, factorial structure, and validity. Methods Three samples of participants were enrolled in the study. (1) A non-patient sample (n = 353) completed the GARS and a set of trait questionnaires to assess internal consistency, test-retest reliability, factorial structure, and concurrent and divergent validity. (2) A sample of patients with SAD (n = 33) was compared to a healthy control group (n = 30) regarding their scores on the GARS and the trait measures. Results The German GARS fear and avoidance scales exhibited excellent internal consistency and high stability over 2 and 4 months, as did the original version. The English version’s factorial structure was replicated, yielding two categories of situations: (1) everyday situations and (2) situations involving high evaluative threat. GARS fear and avoidance displayed convergent validity with trait measures of social anxiety and were markedly higher in patients with GSAD than in healthy controls. Fear and avoidance of eye contact in situations involving high levels of evaluative threat related more closely to social anxiety than to gaze anxiety in everyday situations. Conclusions The German version of the GARS has demonstrated reliability and validity similar to the original version, and is thus well suited to capture fear and avoidance of eye contact in different social situations as a valid self-report measure of social anxiety and related disorders in the social domain for use in both clinical practice and research. PMID:26937638

The German Version of the Gaze Anxiety Rating Scale (GARS): Reliability and Validity.

PubMed

Domes, Gregor; Marx, Lisa; Spenthof, Ines; Heinrichs, Markus

2016-01-01

Fear of eye gaze and avoidance of eye contact are core features of social anxiety disorders (SAD). To measure self-reported fear and avoidance of eye gaze, the Gaze Anxiety Rating Scale (GARS) has been developed and validated in recent years in its English version. The main objectives of the present study were to psychometrically evaluate the German translation of the GARS concerning its reliability, factorial structure, and validity. Three samples of participants were enrolled in the study. (1) A non-patient sample (n = 353) completed the GARS and a set of trait questionnaires to assess internal consistency, test-retest reliability, factorial structure, and concurrent and divergent validity. (2) A sample of patients with SAD (n = 33) was compared to a healthy control group (n = 30) regarding their scores on the GARS and the trait measures. The German GARS fear and avoidance scales exhibited excellent internal consistency and high stability over 2 and 4 months, as did the original version. The English version's factorial structure was replicated, yielding two categories of situations: (1) everyday situations and (2) situations involving high evaluative threat. GARS fear and avoidance displayed convergent validity with trait measures of social anxiety and were markedly higher in patients with GSAD than in healthy controls. Fear and avoidance of eye contact in situations involving high levels of evaluative threat related more closely to social anxiety than to gaze anxiety in everyday situations. The German version of the GARS has demonstrated reliability and validity similar to the original version, and is thus well suited to capture fear and avoidance of eye contact in different social situations as a valid self-report measure of social anxiety and related disorders in the social domain for use in both clinical practice and research.

Household Transmission of Ebola Virus: risks and preventive factors, Freetown, Sierra Leone, 2015.

PubMed

Reichler, Mary R; Bangura, James; Bruden, Dana; Keimbe, Charles; Duffy, Nadia; Thomas, Harold; Knust, Barbara; Farmar, Ishmail; Nichols, Erin; Jambai, Amara; Morgan, Oliver; Hennessy, Thomas

2018-04-06

Knowing risk factors for household transmission of Ebola virus is important to guide preventive measures during Ebola outbreaks. We enrolled all confirmed persons with Ebola who were the first case in a household from December 2014-April 2015 in Freetown, Sierra Leone, and their household contacts. Cases and contacts were interviewed, contacts followed prospectively through the 21-day incubation period, and secondary cases confirmed by laboratory testing. We enrolled 150 index Ebola cases and 838 contacts; 83 (9.9%) contacts developed Ebola during 21-day follow-up. In multivariable analysis, risk factors for transmission included index case death in the household, Ebola symptoms but no reported fever, age <20 years, more days with wet symptoms; and providing care to the index case (P<0.01 for each). Protective factors included avoiding the index case after illness onset and a piped household drinking water source (P<0.01 for each). To reduce Ebola transmission, communities should rapidly identify and follow-up all household contacts; isolate those with Ebola symptoms, including those without reported fever; and consider closer monitoring of contacts who provided care to a case. Households could consider efforts to minimize risk by designating one care provider for ill persons with all others avoiding the suspected case.

Liver Transplant: Complications/Medications

MedlinePlus

... possible airborne fungal spores (e.g. avoiding smoking marijuana , certain occupational exposures), and avoiding contact with sick persons. You do not need to wear masks after you return home. Since the immune system also plays a role in fighting cancer, you will be at increased risk for developing ...

Social reward among juvenile mice

PubMed Central

Panksepp, J B; Lahvis, G P

2007-01-01

Mammalian social relationships, such as mother–offspring attachments and pair bonds, can directly affect reproductive output. However, conspecifics approach one another in a comparatively broad range of contexts, so conceivably there are motivations for social congregation other than those underlying reproduction, parental care or territoriality. Here, we show that reward mediated by social contact is a fundamental aspect of juvenile mouse sociality. Employing a novel social conditioned place preference (SCPP) procedure, we demonstrate that social proximity is rewarding for juvenile mice from three inbred strains (A/J, C57BL/6J and DBA/2J), while mice from a fourth strain (BALB/cJ) are much less responsive to social contact. Importantly, this strain-dependent difference was not related to phenotypic variability in exploratory behavior or contextual learning nor influenced by the genetic background associated with maternal care or social conditioning. Furthermore, the SCPP phenotype was expressed early in development (postnatal day 25) and did not require a specific sex composition within the conditioning group. Finally, SCPP responses resulted from an interaction between two specifiable processes: one component of the interaction facilitated approach toward environments that were associated with social salience, whereas a second component mediated avoidance of environmental cues that predicted social isolation. We have thus identified a genetically prescribed process that can attribute value onto conditions predicting a general form of social contact. To our knowledge, this is the first definitive evidence to show that genetic variation can influence a form of social valuation not directly related to a reproductive behavior. PMID:17212648

Face Gear Drive With Helical Involute Pinion: Geometry, Generation by a Shaper and a Worm, Avoidance of Singularities and Stress Analysis

NASA Technical Reports Server (NTRS)

Litvin, Faydor L.; Fuentes, Alfonso; Gonzalez-Perez, Ignacio; Piscopo, Alessandro; Ruzziconi, Paolo

2005-01-01

A new type of face-gear drive with intersected axes of rotation formed by a helical involute pinion and conjugated face-gear has been investigated. Generation of face-gears by a shaper free of undercutting and pointing has been investigated. A new method of grinding or cutting of face-gears by a worm of special shape has been developed. A computerized design procedure has been developed to avoid undercutting and pointing by a shaper or by a generating worm. Also, a method to determine the limitations of the helix angle magnitude has been developed. The method provides a localization of the bearing contact to reduce the shift of bearing contact caused by misalignment. The analytical method provides a simulation of the meshing and contact of misaligned gear drives. An automatic mesh generation method has been developed and used to conduct a 3D contact stress analysis of several teeth. The theory developed is illustrated with several examples.

Occupational allergic contact dermatitis to nitromethane.

PubMed

Webb, Kelli G; Fowler, Joseph F

2002-12-01

Nitromethane has wide industrial and commercial application as a polar solvent for adhesives and acrylics as well as explosive fuel. Allergic contact dermatitis to this chemical has not been described previously. The authors documented allergic contact hand dermatitis in 4 coworkers who similarly handled an adhesive solvent containing nitromethane. All 4 cases were confirmed by patch testing and resolved after allergen avoidance. Copyright 2002, Elsevier Science (USA)

Allergens retained in clothing.

PubMed

Nedorost, Susan; Kessler, Margaret; McCormick, Thomas

2007-12-01

Some patients state compliance with avoidance of identified allergens, yet have persistent dermatitis in areas under tight-fitting clothing. To analyze a series of such cases to identify allergens most likely retained in clothing. Review of contact dermatitis clinic cases and identification of type and formula weight of allergens involved. High-formula-weight allergens and allergens present in medicament ointments are difficult to dissolve in laundry detergent and water and may be retained in clothing. Retention of allergens in clothing, even after washing, may explain recalcitrant dermatitis in a patient who states compliance with avoidance of a seemingly relevant allergen. Dermatologists should consider the possibility of allergen retention in clothing whenever a patient has only partial clearing after at least 1 month of attempted compliance with avoidance of identified allergens. Purchase of new clothing may be required to clear allergic contact dermatitis in this situation.

NIOSH testimony to DOL on the Occupational Safety and Health Administration's proposed rule on electric power generation, transmission, and distribution; electrical protective equipment by J. D. Millar, November 28, 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-11-28

The testimony concerns the support of NIOSH for the OSHA proposed rule on Electric Power Generation, Transmission and Distribution. NIOSH in particular comments on control of hazardous energy, cardiopulmonary resuscitation, line mechanics, and enclosed spaces. NIOSH estimates that 80 to 90% of the fatalities occurring in the industry occur among line mechanics. NIOSH strongly supports OSHA in applying the standard both electric utility companies and to power generation, transmission and distribution installations not under control of electric utilities. In addition to evaluating electrocutions to find effective ways for workers to avoid electrical injury or fatality, NIOSH has published recommendations formore » providing emergency medical care when workers do inadvertently contact electrical energy. NIOSH is not aware of any epidemiologic study which collected sufficient data to directly address the issue of successful resuscitation following contact with electrical energy. A review of pertinent epidemiologic studies and standard medical practice supports the NIOSH recommendation that workers who may contact energized electrical circuit work in pairs and that both members of the team be trained in cardiopulmonary resuscitation.« less

Conformable liquid metal printed epidermal electronics for smart physiological monitoring and simulation treatment

NASA Astrophysics Data System (ADS)

Wang, Xuelin; Zhang, Yuxin; Guo, Rui; Wang, Hongzhang; Yuan, Bo; Liu, Jing

2018-03-01

Conformable epidermal printed electronics enabled from gallium-based liquid metals (LMs), highly conductive and low-melting-point alloys, are proposed as the core to achieving immediate contact between skin surface and electrodes, which can avoid the skin deformation often caused by conventional rigid electrodes. When measuring signals, LMs can eliminate resonance problems with shorter time to reach steady state than Pt and gelled Pt electrodes. By comparing the contact resistance under different working conditions, it is demonstrated that both ex vivo and in vivo LM electrode-skin models have the virtues of direct and immediate contact with skin surface without the deformation encountered with conventional rigid electrodes. In addition, electrocardio electrodes composed of conformable LM printed epidermal electronics are adopted as smart devices to monitor electrocardiogram signals of rabbits. Furthermore, simulation treatment for smart defibrillation offers a feasible way to demonstrate the effect of liquid metal electrodes (LMEs) on the human body with less energy loss. The remarkable features of soft epidermal LMEs such as high conformability, good conductivity, better signal stability, and fine biocompatibility represent a critical step towards accurate medical monitoring and future smart treatments.

The dilemma of contact: voluntary isolation and the impacts of gas exploitation on health and rights in the Kugapakori Nahua Reserve, Peruvian Amazon

NASA Astrophysics Data System (ADS)

Napolitano, Dora A.; Ryan, Aliya S. S.

2007-10-01

Many small groups of indigenous peoples in the Amazon basin avoid and resist direct encounters with outsiders. As far as we know, they do so because of appalling experiences in earlier encounters with national society. When contacted today, they are extremely vulnerable to introduced diseases and exploitation. In this paper we draw on our experience in the Kugapakori Nahua Reserve for isolated peoples in SE Peru to discuss some of the current debates about whether isolated peoples should be contacted and how best to respect their right to life, health, autonomy and territory. The remote headwater regions where isolated peoples sought refuge during the last century are increasingly sought after for resource extraction. In particular, the extraction of oil and gas is increasing throughout the Peruvian Amazon. In the second part of the paper we give some examples of how oil/gas companies and the energy sector in Peru have affected the well-being of the peoples in this reserve in the 21st century. If this trend is not reversed the impacts for isolated peoples will be irreparable.

Dynamic contact angle cycling homogenizes heterogeneous surfaces.

PubMed

Belibel, R; Barbaud, C; Mora, L

2016-12-01

In order to reduce restenosis, the necessity to develop the appropriate coating material of metallic stent is a challenge for biomedicine and scientific research over the past decade. Therefore, biodegradable copolymers of poly((R,S)-3,3 dimethylmalic acid) (PDMMLA) were prepared in order to develop a new coating exhibiting different custom groups in its side chain and being able to carry a drug. This material will be in direct contact with cells and blood. It consists of carboxylic acid and hexylic groups used for hydrophilic and hydrophobic character, respectively. The study of this material wettability and dynamic surface properties is of importance due to the influence of the chemistry and the potential motility of these chemical groups on cell adhesion and polymer kinetic hydrolysis. Cassie theory was used for the theoretical correction of contact angles of these chemical heterogeneous surfaces coatings. Dynamic Surface Analysis was used as practical homogenizer of chemical heterogeneous surfaces by cycling during many cycles in water. In this work, we confirmed that, unlike receding contact angle, advancing contact angle is influenced by the difference of only 10% of acidic groups (%A) in side-chain of polymers. It linearly decreases with increasing acidity percentage. Hysteresis (H) is also a sensitive parameter which is discussed in this paper. Finally, we conclude that cycling provides real information, thus avoiding theoretical Cassie correction. H(10)is the most sensible parameter to %A. Copyright © 2016 Elsevier B.V. All rights reserved.

[Restoration of the idea of contact. Psychopedagogic approach].

PubMed

Richaud, R L

1988-01-01

Our psychopedagogical work with teenagers having serious problems in the school setting led us to set up a clinical approach giving back to thought the ability to link affects and their representations whereas the thought process had seemed exhausted by a never-ending fight to avoid being swallowed up by the primary processes or through representing unbearable phantasms. In our hypothesis, as long as the imaginary can't be represented, it blocks access to any idea of contact. Having contact with works of art, which can serve as models of metamorphosis that has succeeded, seemed, to us, in the concept of a shared dream, as the best way to allows patients to reconnect lost or avoided parts, but from afar. The metaphor takes the place of the nameless crudity and horror of a very real alienating agent.

Why are all the white (Asian) kids sitting together in the cafeteria? Resegregation and the role of intergroup attributions and norms.

PubMed

Ramiah, Ananthi Al; Schmid, Katharina; Hewstone, Miles; Floe, Christina

2015-03-01

Over three studies, we identified the phenomenon of ethnic 'resegregation' and assessed the extent to which it was predicted by attributions and norms, among other variables. Study 1, an observational study, showed extensive resegregation between White and Asian students in the cafeteria of a highly mixed school. In Study 2, we found evidence of attributional correspondence for White students, who attributed both their own and the outgroup's contact avoidance more to a lack of interest than fear of rejection, whereas Asian students attributed the outgroup's contact avoidance more to lack of interest, but preferred neither explanation of their own avoidance. In Study 3, we observed a pattern of attributional correspondence among both White and Asian students who attributed both their own and the outgroup's inaction in a hypothetical intergroup cafeteria scenario more to a lack of interest than fear of rejection. Study 3 also demonstrated longitudinally, for both groups, that own lack of interest in the outgroup reduced likelihood of cafeteria contact, whereas having outgroup friends and perceiving positive ingroup norms promoted it. In addition, positive outgroup norms promoted likelihood of cafeteria contact only for Asian students. We discuss how an understanding of the factors driving resegregation is critical to effectively realizing the potential of desegregated settings. © 2014 The British Psychological Society.

Procedure for pressure contact on high-power semiconductor devices free of thermal fatigue

NASA Technical Reports Server (NTRS)

Knobloch, J.

1979-01-01

To eliminate thermal fatigue, a procedure for manufacturing semiconductor power devices with pure pressure contact without solid binding was developed. Pressure contact without the use of a solid binding to avoid a limitation of the maximum surface in the contact was examined. A silicon wafer covered with a relatively thick metal layer is imbedded with the aid of a soft silver foil between two identically sized hard contact discs (molybdenum or tungsten) which are rotationally symmetrical. The advantages of this concept are shown for large diameters. The pressure contact was tested successfully in many devices in a large variety of applications.

9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Hard surfaces with which nonhuman primates come in contact must be spot-cleaned daily and sanitized in... must be raked or spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be removed or replaced whenever raking and spot cleaning...

9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... Hard surfaces with which nonhuman primates come in contact must be spot-cleaned daily and sanitized in... must be raked or spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be removed or replaced whenever raking and spot cleaning...

9 CFR 3.1 - Housing facilities, general.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... Hard surfaces with which the dogs or cats come in contact must be spot-cleaned daily and sanitized in... spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be replaced whenever this raking and spot-cleaning is not sufficient to prevent or...

9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... Hard surfaces with which nonhuman primates come in contact must be spot-cleaned daily and sanitized in... must be raked or spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be removed or replaced whenever raking and spot cleaning...

9 CFR 3.1 - Housing facilities, general.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... Hard surfaces with which the dogs or cats come in contact must be spot-cleaned daily and sanitized in... spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be replaced whenever this raking and spot-cleaning is not sufficient to prevent or...

9 CFR 3.1 - Housing facilities, general.

Code of Federal Regulations, 2012 CFR

2012-01-01

.... Hard surfaces with which the dogs or cats come in contact must be spot-cleaned daily and sanitized in... spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be replaced whenever this raking and spot-cleaning is not sufficient to prevent or...

School Job Placement: Can It Avoid Reproducing Social Inequalities?

ERIC Educational Resources Information Center

Redline, Julie E.; Rosenbaum, James E.

2010-01-01

Background: Labor market entry is difficult for two-year college graduates. Job search literature focuses on personal connections, but disadvantaged students often lack useful contacts. Moreover, employers often don't recognize and value two-year college credentials as much as bachelor's degrees. Teacher contacts could help, but studies find that…

Noninvasive estimation of assist pressure for direct mechanical ventricular actuation

NASA Astrophysics Data System (ADS)

An, Dawei; Yang, Ming; Gu, Xiaotong; Meng, Fan; Yang, Tianyue; Lin, Shujing

2018-02-01

Direct mechanical ventricular actuation is effective to reestablish the ventricular function with non-blood contact. Due to the energy loss within the driveline of the direct cardiac compression device, it is necessary to acquire the accurate value of assist pressure acting on the heart surface. To avoid myocardial trauma induced by invasive sensors, the noninvasive estimation method is developed and the experimental device is designed to measure the sample data for fitting the estimation models. By examining the goodness of fit numerically and graphically, the polynomial model presents the best behavior among the four alternative models. Meanwhile, to verify the effect of the noninvasive estimation, the simplified lumped parameter model is utilized to calculate the pre-support and the post-support left ventricular pressure. Furthermore, by adjusting the driving pressure beyond the range of the sample data, the assist pressure is estimated with the similar waveform and the post-support left ventricular pressure approaches the value of the adult healthy heart, indicating the good generalization ability of the noninvasive estimation method.

Contact angle hysteresis and motion behaviors of a water nano-droplet on suspended graphene under temperature gradient

NASA Astrophysics Data System (ADS)

Foroutan, Masumeh; Fatemi, S. Mahmood; Esmaeilian, Farshad; Fadaei Naeini, Vahid; Baniassadi, Majid

2018-05-01

In the present work, the effect of temperature gradient on the behavior of a water nano-droplet resting on a suspended graphene was studied based on a non-equilibrium molecular dynamics simulation. The acquired results indicate that the applied temperature gradient to the suspended graphene drives the water nano-droplet to the colder region. The droplet accelerates its motion toward the cold reservoir as the temperature gradient is increased. In addition to the translational motion of the nano-droplet, the vortical motion of the water molecules was also observed. Contact angle analysis was also utilized to describe the directional motion of the nano-droplet. The translational motion of the droplet leads to the estimation of contact angle hysteresis through advancing and receding contact angles while the rotational motion resulted in the advancing and receding fronts being switched with one another through the simulation. The average displacement vector of the water molecules shows that parts of the droplet seem to stagnate while other parts rotate around them. The reason behind this particular behavior was studied based on interaction energy contours between a water molecule and the suspended graphene. The obtained data indicate that the rotational motion is in agreement with the migration of the water molecules to low interaction energy regions in order to avoid high interaction energy areas.

Computerized Design and Generation of Low-Noise Gears with Localized Bearing Contact

NASA Technical Reports Server (NTRS)

Litvin, Faydor L.; Chen, Ningxin; Chen, Jui-Sheng; Lu, Jian; Handschuh, Robert F.

1995-01-01

The results of research projects directed at the reduction of noise caused by misalignment of the following gear drives: double-circular arc helical gears, modified involute helical gears, face-milled spiral bevel gears, and face-milled formate cut hypoid gears are presented. Misalignment in these types of gear drives causes periodic, almost linear discontinuous functions of transmission errors. The period of such functions is the cycle of meshing when one pair of teeth is changed for the next. Due to the discontinuity of such functions of transmission errors high vibration and noise are inevitable. A predesigned parabolic function of transmission errors that is able to absorb linear discontinuous functions of transmission errors and change the resulting function of transmission errors into a continuous one is proposed. The proposed idea was successfully tested using spiral bevel gears and the noise was reduced a substantial amount in comparison with the existing design. The idea of a predesigned parabolic function is applied for the reduction of noise of helical and hypoid gears. The effectiveness of the proposed approach has been investigated by developed TCA (tooth contact analysis) programs. The bearing contact for the mentioned gears is localized. Conditions that avoid edge contact for the gear drives have been determined. Manufacturing of helical gears with new topology by hobs and grinding worms has been investigated.

Biomechanical Effects of Posterior Condylar Offset and Posterior Tibial Slope on Quadriceps Force and Joint Contact Forces in Posterior-Stabilized Total Knee Arthroplasty.

PubMed

Kang, Kyoung-Tak; Koh, Yong-Gon; Son, Juhyun; Kwon, Oh-Ryong; Lee, Jun-Sang; Kwon, Sae Kwang

2017-01-01

This study aimed to determine the biomechanical effect of the posterior condylar offset (PCO) and posterior tibial slope (PTS) in posterior-stabilized (PS) fixed-bearing total knee arthroplasty (TKA). We developed ±1, ±2, and ±3 mm PCO models in the posterior direction and -3°, 0°, 3°, and 6° PTS models using a previously validated FE model. The influence of changes in the PCO and PTS on the biomechanical effects under deep-knee-bend loading was investigated. The contact stress on the PE insert increased by 14% and decreased by 7% on average as the PCO increased and decreased, respectively, compared to the neutral position. In addition, the contact stress on post in PE insert increased by 18% on average as PTS increased from -3° to 6°. However, the contact stress on the patellar button decreased by 11% on average as PTS increased from -3° to 6° in all different PCO cases. The quadriceps force decreased by 14% as PTS increased from -3° to 6° in all PCO models. The same trend was found in patellar tendon force. Changes in PCO had adverse biomechanical effects whereas PTS increase had positive biomechanical effects. However, excessive PTS should be avoided to prevent knee instability and subsequent failure.

Gap junction-dependent homolog avoidance in the developing CNS.

PubMed

Baker, Michael W; Yazdani, Neema; Macagno, Eduardo R

2013-10-16

Oppositely directed projections of some homologous neurons in the developing CNS of the medicinal leech (Hirudo verbana), such as the AP cells, undergo a form of contact-dependent homolog avoidance. Embryonic APs extend axons within the connective nerve toward adjacent ganglia, in which they meet and form gap junctions (GJs) with the oppositely directed axons of their segmental homologs, stop growing, and are later permanently retracted (Wolszon et al., 1994a,b). However, early deletion of an AP neuron leads to resumed growth and permanent maintenance of the projections of neighboring APs. Here we test the hypothesis that a GJ-based signaling mechanism is responsible for this instance of homolog avoidance. We demonstrate that selective knockdown of GJ gene Hve-inx1 expression in single embryonic APs, by expressing a short-hairpin interfering RNA, leads to continued growth of the projections of the cell toward, into, and beyond adjacent ganglia. Moreover, the projections of the APs in adjacent ganglia also resume growth, mimicking their responses to cell deletion. Continued growth was also observed when two different INX1 mutant transgenes that abolish dye coupling between APs were expressed. These include a mutant transgene that effectively downregulates all GJ plaques that include the INX1 protein and a closed channel INX1 mutant that retains the adhesive cellular binding characteristic of INX1 GJs but not the open channel pore function. Our results add GJ intercellular communication to the list of molecular signaling mechanisms that can act as mediators of growth-inhibiting cell-cell interactions that define the topography of neuronal arbors.

46 CFR 120.320 - Generators and motors.

Code of Federal Regulations, 2012 CFR

2012-10-01

... and Distribution Systems § 120.320 Generators and motors. (a) Each generator and motor must be: (1) In... above the bilges to avoid damage by splash and to avoid contact with low lying vapors. (b) Each... ammeter, which can be used for measuring voltage and current of a generator that is in operation, must be...

46 CFR 120.320 - Generators and motors.

Code of Federal Regulations, 2014 CFR

2014-10-01

... and Distribution Systems § 120.320 Generators and motors. (a) Each generator and motor must be: (1) In... above the bilges to avoid damage by splash and to avoid contact with low lying vapors. (b) Each... ammeter, which can be used for measuring voltage and current of a generator that is in operation, must be...

46 CFR 120.320 - Generators and motors.

Code of Federal Regulations, 2013 CFR

2013-10-01

... and Distribution Systems § 120.320 Generators and motors. (a) Each generator and motor must be: (1) In... above the bilges to avoid damage by splash and to avoid contact with low lying vapors. (b) Each... ammeter, which can be used for measuring voltage and current of a generator that is in operation, must be...

The mediating effect of self-esteem, depression and anxiety between satisfaction with body appearance and problematic internet use.

PubMed

Koronczai, Beatrix; Kökönyei, Gyöngyi; Urbán, Róbert; Kun, Bernadette; Pápay, Orsolya; Nagygyörgy, Katalin; Griffiths, Mark D; Demetrovics, Zsolt

2013-07-01

Given that dissatisfaction with bodily appearance can sometimes lead to the avoidance of personal contacts and the increase of internet use, this study examines this relationship. The direct role of dissatisfaction with bodily appearance along with the possible mediation effects of depression, anxiety and self-esteem were tested. A total of 694 participants completed an online questionnaire (58.5% male, mean age 21.5 years), containing measures on problematic internet use, depression and anxiety symptoms, self-esteem and satisfaction with body image. Path analyses were used to test direct and indirect effects. Satisfaction with body appearance had a significant negative direct effect on problematic internet use among both sexes. Though, satisfaction with body appearance had a positive effect on self-esteem and negative on anxiety, neither self-esteem nor anxiety had a direct significant effect on problematic internet use. The effect of dissatisfaction with body appearance was mediated via the self-esteem-depression path toward problematic internet use. Dissatisfaction with physical appearance seems to have a significant role in individuals' immersing themselves in internet use.

Handbook on Face Gear Drives with a Spur Involute Pinion

NASA Technical Reports Server (NTRS)

Litvin, F. L.; Egelja, A.; Tan, J.; Chen, D. Y.-D.; Heath, G.

2000-01-01

The use of face gears in power transmission and drive systems has a significant number of benefits. Face gears allow a variety of new transmission arrangements as well as high reduction ratio capability. This leads to drive system weight reduction and improvements in performance. In this work, basic information about the design and analysis of face gear drives is presented. The work considers face gears in mesh with spur involute pinions for both intersecting axes and offset drives. Tooth geometry, kinematics, generation of face gears with localized bearing contact by cutting and grinding, avoidance of tooth undercutting, avoidance of tooth pointing, tooth contact analysis, and algorithms for the simulation of meshing and contact arc all topics which are discussed. In addition, applications of face gear drives are presented. Included are design uses in aerospace applications such as helicopter transmissions, split-torque face gear arrangements, comparisons of face gears with bevel gears, and general design considerations.

Pigment dispersion syndrome associated with intraocular lens implantation: a new surgical technique.

PubMed

Canut Jordana, M Isabel; Pérez Formigó, Daniel; Abreu González, Rodrigo; Nadal Reus, Jeroni

2010-11-11

We report the case of a myopic patient who, after intraocular lens transplant in the posterior chamber, suffered elevated intraocular pressure due to pigment dispersion, with recurrent episodes of blurred vision. The patient was treated with a new surgical technique that can avoid potential iridolenticular contact. Complete ophthalmologic examination and optical coherence tomography (OCT) of the anterior segment were performed. Contact between the pigmentary epithelium and the iris with an intraocular lens was revealed by utrasound biomicroscopy and OCT. In this case, Nd:YAG laser iridotomy and laser iridoplasty were not effective for iridolenticular separation and control of the pigment dispersion. We propose a new technique: stitches on the surface of the iris to obtain good iridolenticular separation and good intraocular pressure control. Stitches on the iris surface should be considered as optional therapy in pigmentary glaucoma secondary to intraocular lens implantation. This surgical technique can avoid potential iridolenticular contacts more definitively.

[A case of vocal cord contact granuloma after vocal cord polyp surgery].

PubMed

Qiu, Zhili; Jiang, Xiaoping; Yuan, Xiaodong

2016-01-01

The vocal cord polyp is easy to relapse after surgery, but if the patient has recurrence in a short term, it is necessary to consider it as postoperative vocal cord contact granuloma. If the patients with contact granuloma after surgical treatment had severe impact on the pronunciation, it is necessary to be operated and confirmed by pathology and given the treatment of acid suppression, in order to avoid postoperative recurrence.

Triggers of oral lichen planus flares and the potential role of trigger avoidance in disease management.

PubMed

Chen, Hannah X; Blasiak, Rachel; Kim, Edwin; Padilla, Ricardo; Culton, Donna A

2017-09-01

Many patients with oral lichen planus (OLP) report triggers of flares, some of which overlap with triggers of other oral diseases, including oral allergy syndrome and oral contact dermatitis. The purpose of this study was to evaluate the prevalence of commonly reported triggers of OLP flares, their overlap with triggers of other oral diseases, and the potential role of trigger avoidance as a management strategy. Questionnaire-based survey of 51 patients with biopsy-proven lichen planus with oral involvement seen in an academic dermatology specialty clinic and/or oral pathology clinic between June 2014 and June 2015. Of the participants, 94% identified at least one trigger of their OLP flares. Approximately half of the participants (51%) reported at least one trigger that overlapped with known triggers of oral allergy syndrome, and 63% identified at least one trigger that overlapped with known triggers of oral contact dermatitis. Emotional stress was the most commonly reported trigger (77%). Regarding avoidance, 79% of the study participants reported avoiding their known triggers in daily life. Of those who actively avoided triggers, 89% reported an improvement in symptoms and 70% reported a decrease in the frequency of flares. Trigger identification and avoidance can play a potentially effective role in the management of OLP. Copyright © 2017 Elsevier Inc. All rights reserved.

Collecting Social Network Data from Mobile Phone SIM Cards

ERIC Educational Resources Information Center

Peseckas, Ryan

2016-01-01

I used a subscriber identity module card reader to copy the lists of saved contacts from 170 mobile phones in Fiji. This approach has both advantages and disadvantages compared to other techniques for collecting telephone network data. Copying phone contacts avoids recall biases associated with survey-based name generators. It also obviates the…

The Acoustoelectric and Electric Characterization of Single Layer Transition Metal Dichalcogenides

NASA Astrophysics Data System (ADS)

Preciado, Edwin Sabas

The acoustoelectric effect in single-layer molybdenum disulfide (MoS2) and tungsten diselenide (WSe2) is studied in a hybrid setup. Such effects, which rely on the transfer of momentum from surface acoustic waves (SAWs), are generated on the surface of lithium niobate (LiNbO3) to the carriers in MoS2 and WSe2, resulting in an attenuation and velocity shift of the wave and giving rise to an acoustoelectric current. This dissertation examines the feasibility of integrating high-quality, single-layer MoS2 and WSe2 onto LiNbO3 to ultimately fabricate and characterize a hybrid chip that combines the functionality of a field-effect transistor (FET) and SAW device. MoS2 and WSe2 were synthesized by chemical vapor deposition (CVD) directly onto a chemically-reduced LiNbO3 substrate. LiNbO3 is a ferroelectric material that offers a unique blend of piezoelectric and birefringent properties, yet it lacks both optical activity and semiconductor transport. The prototypical device exhibits electrical characteristics that are competitive with MoS2 and WSe2 devices on silicon. These results demonstrate both a sound-driven battery and an acoustic photodetector, and ultimately open directions to non-invasive investigation of electrical properties of single-layer films. The experiments reveal close agreement between transport measurements utilizing conventional contacts and SAW spectroscopy. This approach will set forth the possibility of contact-free transport characterization of two-dimensional (2D) transition metal dichalcogenides (TMD) films, avoiding such concerns as the role of charge transfer at contacts as an artifact of such measurements.

Dog and Cat Allergies and Allergen Avoidance Measures in Korean Adult Pet Owners Who Participated in a Pet Exhibition.

PubMed

Yang, Min Suk; Lee, Sang Pyo; Kwon, Young Jae; Lee, Sang Min

2018-03-01

This study evaluated dog and cat allergies and their association with allergen avoidance measures in Korean adults. The study population consisted of 537 adults who currently kept dogs or cats and participated in a pet exhibition in Korea. The subjects were asked to complete questionnaires regarding pet ownership, allergen avoidance, and allergy symptoms, and underwent skin prick tests. They were considered to have a dog or cat allergy if they suffered from one or more of allergy symptoms during contact with their pets. In total, 103 of 407 dog owners (25.3%) and 45 of 130 cat owners (34.6%) had a dog or cat allergy, respectively. Dog owners kept 1.3±1.5 dogs; this number did not differ according to the presence of dog allergy. Dog owners with a dog allergy had owned their dogs longer than those without (88.0±72.0 vs 67.5±72.7 months, P<0.05). Cat owners kept 2.1±3.6 cats; this number did not differ according to the presence of cat allergy, nor did the duration of cat ownership. Cat owners with a cat allergy had facial contact and slept with their cats less frequently (8.6±11.9 vs 18.3±27.0 times/day, P<0.01; 71.1% vs 81.2%, P<0.05); however, they had their cats shaved and beds cleaned less frequently than those without (1.8±3.3 vs 3.2±4.4 times/year, P<0.05; 1.5±1.5 vs 3.9±6.0 times/month, P<0.01). Cat owners with a cat allergy tried to minimize contact with their cats, but efforts to avoid indoor cat allergens were lower than those without. In comparison, dog owners with a dog allergy had kept their dogs for longer time than those without; however, current contact with their dogs and allergen avoidance measures did not differ between the 2 groups. Copyright © 2018 The Korean Academy of Asthma, Allergy and Clinical Immunology · The Korean Academy of Pediatric Allergy and Respiratory Disease

Hand hygiene in rural Indonesian healthcare workers: barriers beyond sinks, hand rubs and in-service training.

PubMed

Marjadi, B; McLaws, M-L

2010-11-01

Few attempts to increase healthcare workers' hand hygiene compliance have included an in-depth analysis of the social and behavioural context in which hand hygiene is not undertaken. We used a mixed method approach to explore hand hygiene barriers in rural Indonesian healthcare facilities to develop a resource-appropriate adoption of international guidelines. Two hospitals and eight clinics (private and public) in a rural Indonesian district were studied for three months each. Hand hygiene compliance was covertly observed for two shifts each in three adult wards at two hospitals. Qualitative data were collected from direct observation, focus group discussions and semistructured in-depth and informal interviews within healthcare facilities and the community. Major barriers to compliance included longstanding water scarcity, tolerance of dirtiness by the community and the healthcare organisational culture. Hand hygiene compliance was poor (20%; 57/281; 95% CI: 16-25%) and was more likely to be undertaken after patient contact (34% after-patient contact vs 5% before-patient contact, P<0.001) and 'inherent' opportunities associated with contacts perceived to be dirty (49% 'inherent' vs 11% 'elective' opportunities associated with clean contacts, P<0.001). Clinicians frequently touched patients without hand hygiene, and some clinicians avoided touching patients altogether. The provision of clean soap and water and in-service training will not overcome strong social and behavioural barriers unless interventions focus on long term community education and managerial commitment to the provision of supportive working conditions. Copyright © 2010 The Hospital Infection Society. All rights reserved.

Touchless attitude correction for satellite with constant magnetic moment

NASA Astrophysics Data System (ADS)

Ao, Hou-jun; Yang, Le-ping; Zhu, Yan-wei; Zhang, Yuan-wen; Huang, Huan

2017-09-01

Rescue of satellite with attitude fault is of great value. Satellite with improper injection attitude may lose contact with ground as the antenna points to the wrong direction, or encounter energy problems as solar arrays are not facing the sun. Improper uploaded command may set the attitude out of control, exemplified by Japanese Hitomi spacecraft. In engineering practice, traditional physical contact approaches have been applied, yet with a potential risk of collision and a lack of versatility since the mechanical systems are mission-specific. This paper puts forward a touchless attitude correction approach, in which three satellites are considered, one having constant dipole and two having magnetic coils to control attitude of the first. Particular correction configurations are designed and analyzed to maintain the target's orbit during the attitude correction process. A reference coordinate system is introduced to simplify the control process and avoid the singular value problem of Euler angles. Based on the spherical triangle basic relations, the accurate varying geomagnetic field is considered in the attitude dynamic mode. Sliding mode control method is utilized to design the correction law. Finally, numerical simulation is conducted to verify the theoretical derivation. It can be safely concluded that the no-contact attitude correction approach for the satellite with uniaxial constant magnetic moment is feasible and potentially applicable to on-orbit operations.

76 FR 5280 - Determination of Attainment for PM10

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-31

... contact the individual listed in the FOR FURTHER INFORMATION CONTACT section to view the hard copy of the docket. You may view the hard copy of the docket Monday through Friday, 8 a.m. to 4 p.m., excluding..., and suggest alternatives. g. Explain your views as clearly as possible, avoiding the use of profanity...

Vines and canopy contact: a route for snake predation on parrot nests.

Treesearch

SUSAN E. KOENIG; JOSEPH M. WUNDERLE; ERNESTO C. ENKERLINHOEFLICH

2007-01-01

Ornithologists have hypothesized that some tropical forest birds avoid snake predation by nesting in isolated trees that do not have vines and canopy contact with neighbouring trees. Here we review two complementary studies that support this hypothesis by demonstrating (1) that an abundance of vines and an interlocking canopy characterized Jamaican Black-billed Parrot...

[When sunscreens do not help: allergic contact dermatitis to UV filters].

PubMed

Ludriksone, L; Tittelbach, J; Schliemann, S; Goetze, S; Elsner, P

2018-06-07

Ultraviolet (UV) filters may cause allergic and more frequently photoallergic contact dermatitis. Therefore, a photopach test should always be performed in case of a suspected contact sensitivity to UV filters. We report a case of a 65-year-old woman with a recurrent erythema of the face and décolleté after sun exposure despite application of a sunscreen. The (photo)patch test revealed a contact sensitivity to the UV filter butyl-methoxybenzoylmethane. Treatment with a topical glucocorticoid and avoidance of the particular UV filter led to a rapid improvement.

Evaluating the impact of direct and indirect contact on the mental health stigma of pharmacy students.

PubMed

Nguyen, Elizabeth; Chen, Timothy F; O'Reilly, Claire L

2012-07-01

Contact with mental health consumers has shown to be a promising strategy to address mental health stigma, particularly in the context of pharmacy education. This research aimed to compare the effectiveness of a direct (face-to-face) contact intervention with an indirect (film based) contact intervention in reducing the mental health stigma of pharmacy students. A two-group, non-randomized, comparative study was conducted with third year pharmacy students (n = 198) allocated to the direct contact arm and fourth year pharmacy students (n = 278) allocated to the indirect contact arm. Baseline and immediate post-intervention data were collected using a validated 39 item survey instrument to assess the impact of the interventions on mental health stigma as well as attitudes towards providing mental health pharmaceutical services. Participants in the direct contact group showed a significant improvement in 37 out of 39 survey items and participants in the indirect contact group showed a significant improvement in 27 out of 39 items (P < 0.05). While direct contact had a stronger impact than indirect contact for 22 items (P < 0.05), for numerous key measures of mental health stigma the impact of the two contact interventions was equivalent. Both indirect and direct contact may positively impact mental health stigma. While the strength of the stigma-change process may be heightened by face-to-face interactions, the largely positive impact of indirect contact suggests that stigma reduction may depend less on the medium of contact but more on the transcendent messages contributed by the consumers facilitating the contact experience.

Adhesion and friction of the smooth attachment system of the cockroach Gromphadorhina portentosa and the influence of the application of fluid adhesives

PubMed Central

Frenzel, Melina; Steiner, Michael; Vogt, Martin; Kleemeier, Malte; Hartwig, Andreas; Sampalla, Benjamin; Rupp, Frank; Boley, Moritz; Schmitt, Christian

2017-01-01

ABSTRACT Two different measurement techniques were applied to study the attachment of the smooth foot pads of the Madagascar hissing cockroach Gromphadorhina portentosa. The attachment of the non-manipulated adhesive organs was compared with that of manipulated ones (depletion or substitution by artificial secretions). From measurements of the friction on a centrifuge, it can be concluded that on nanorough surfaces, the insect appears to benefit from employing emulsions instead of pure oils to avoid excessive friction. Measurements performed with a nanotribometer on single attachment organs showed that, in the non-manipulated euplantulae, friction was clearly increased in the push direction, whereas the arolium of the fore tarsus showed higher friction in the pull direction. The surface of the euplantulae shows an imbricate appearance, whereupon the ledges face distally, which might contribute to the observed frictional anisotropy in the push direction. Upon depletion of the tarsal adhesion-mediating secretion or its replacement by oily fluids, in several cases, the anisotropic effect of the euplantula disappeared due to the decrease of friction forces in push-direction. In the euplantulae, adhesion was one to two orders of magnitude lower than friction. Whereas the tenacity was slightly decreased with depleted secretion, it was considerably increased after artificial application of oily liquids. In terms of adhesion, it is concluded that the semi-solid consistence of the natural adhesion-mediating secretion facilitates the detachment of the tarsus during locomotion. In terms of friction, on smooth to nanorough surfaces, the insects appear to benefit from employing emulsions instead of pure oils to avoid excessive friction forces, whereas on rougher surfaces the tarsal fluid rather functions in improving surface contact by keeping the cuticle compliable and compensating surface asperities of the substratum. PMID:28507055

Exploring expert opinion on the practicality and effectiveness of biosecurity measures on dairy farms in the United Kingdom using choice modeling.

PubMed

Shortall, Orla; Green, Martin; Brennan, Marnie; Wapenaar, Wendela; Kaler, Jasmeet

2017-03-01

Biosecurity, defined as a series of measures aiming to stop disease-causing agents entering or leaving an area where farm animals are present, is very important for the continuing economic viability of the United Kingdom dairy sector, and for animal welfare. This study gathered expert opinion from farmers, veterinarians, consultants, academics, and government and industry representatives on the practicality and effectiveness of different biosecurity measures on dairy farms. The study used best-worst scaling, a technique that allows for greater discrimination between choices and avoids the variability in interpretation associated with other methods, such as Likert scales and ranking methods. Keeping a closed herd was rated as the most effective measure overall, and maintaining regular contact with the veterinarian was the most practical measure. Measures relating to knowledge, planning, and veterinary involvement; buying-in practices; and quarantine and treatment scored highly for effectiveness overall. Measures relating to visitors, equipment, pest control, and hygiene scored much lower for effectiveness. Overall, measures relating to direct animal-to-animal contact scored much higher for effectiveness than measures relating to indirect disease transmission. Some of the most effective measures were also rated as the least practical, such as keeping a closed herd and avoiding nose-to-nose contact between contiguous animals, suggesting that real barriers exist for farmers when implementing biosecurity measures on dairy farms. We observed heterogeneity in expert opinion on biosecurity measures; for example, veterinarians rated the effectiveness of consulting the veterinarian on biosecurity significantly more highly than dairy farmers, suggesting a greater need for veterinarians to promote their services on-farm. Still, both groups rated it as a practical measure, suggesting that the farmer-veterinarian relationship holds some advantages for the promotion of biosecurity. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

21 CFR 882.1570 - Powered direct-contact temperature measurement device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Powered direct-contact temperature measurement... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1570 Powered direct-contact temperature measurement device. (a) Identification. A powered direct...

21 CFR 882.1570 - Powered direct-contact temperature measurement device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Powered direct-contact temperature measurement... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1570 Powered direct-contact temperature measurement device. (a) Identification. A powered direct...

21 CFR 882.1570 - Powered direct-contact temperature measurement device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Powered direct-contact temperature measurement... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1570 Powered direct-contact temperature measurement device. (a) Identification. A powered direct...

Comparison of nickel silicide and aluminium ohmic contact metallizations for low-temperature quantum transport measurements.

PubMed

Polley, Craig M; Clarke, Warrick R; Simmons, Michelle Y

2011-10-03

We examine nickel silicide as a viable ohmic contact metallization for low-temperature, low-magnetic-field transport measurements of atomic-scale devices in silicon. In particular, we compare a nickel silicide metallization with aluminium, a common ohmic contact for silicon devices. Nickel silicide can be formed at the low temperatures (<400°C) required for maintaining atomic precision placement in donor-based devices, and it avoids the complications found with aluminium contacts which become superconducting at cryogenic measurement temperatures. Importantly, we show that the use of nickel silicide as an ohmic contact at low temperatures does not affect the thermal equilibration of carriers nor contribute to hysteresis in a magnetic field.

Optimizing radiofrequency ablation of paroxysmal and persistent atrial fibrillation by direct catheter force measurement-a case-matched comparison in 198 patients.

PubMed

Sigmund, Elisabeth; Puererfellner, Helmut; Derndorfer, Michael; Kollias, Georgios; Winter, Siegmund; Aichinger, Josef; Nesser, Hans-Joachim; Martinek, Martin

2015-02-01

Sufficient electrode-tissue contact is crucial for adequate lesion formation in radiofrequency catheter ablation (RFCA). We assessed the impact of direct catheter force measurement on acute procedural parameters and outcome of RFCA for paroxysmal and persistent atrial fibrillation (AF). Ninety-nine consecutive patients (70% men) with paroxysmal (63.6%) or persistent AF underwent left atrial RFCA using a 3.5-mm open-irrigated-tip (OIT) catheter with contact force measurement capabilities (group 1). For comparison a case-matched cohort with standard OIT catheters was used (99 patients; group 2). Case matching included gender, type of AF, number or RFCA procedures, and type of procedure. Procedural data showed a significant decline in radiofrequency ablation time from 52 ± 20 to 44 ± 16 minutes (P = 0.003) with a remarkable mean reduction in overall procedure time of 34 minutes (P = 0.0001; 225.8 ± 53.1 vs 191.9 ± 53.3 minutes). In parallel, the total fluoroscopy time could be significantly reduced from 28.5 ± 11.0 to 19.9 ± 9.3 minutes (P = 0.0001) as well as fluoroscopy dose from 74.1 ± 58.0 to 56.7 ± 38.9 Gy/cm(2) (P = 0.016). Periprocedural complications were similar in both groups. The use of contact force sensing technology is able to significantly reduce ablation, procedure, and fluoroscopy times as well as dose in RFCA of AF in a mixed case-matched group of paroxysmal and persistent AF. Energy delivery is substantially reduced by avoiding radiofrequency ablation in positions with insufficient surface contact. Additionally 12-month outcome data showed increased efficacy. Such time saving and equally safe technology may have a relevant impact on laboratory management and increased cost effectiveness. © 2014 Wiley Periodicals, Inc.

Leptospirosis: risks during recreational activities.

PubMed

Monahan, A M; Miller, I S; Nally, J E

2009-09-01

Summary Rats, dogs, cattle, bats and sea lions, exemplify the diversity of mammalian species that can facilitate transmission of the zoonotic disease leptospirosis. The causative agent, pathogenic species of Leptospira, is shed in urine of chronically infected hosts. Direct contact with infected urine, or indirectly with water sources contaminated with infected urine, poses a risk of infection for humans exposed during water-related recreational and occupational activities. New serovars of Leptospira and maintenance hosts continue to be identified. In the western world, incidences of recreational exposure are increasing, while incidences of occupational exposure are decreasing. Adventure travellers returning from tropical regions, are presenting at clinics with symptoms of leptospirosis following participation in high risk activities including white water rafting, triathlons, endurance races and caving. Risks of infection can be reduced with increased awareness of how the disease is contracted, by avoiding contact with high risk water sources and the use of prophylaxis during high risk activities. Molecular techniques can be used to provide risk assessments prior to competition, to supplement epidemiology, and to assess shedding of Leptospira in urine samples.

Examining Challenging Behaviors of Clients with Borderline Personality Disorder

PubMed Central

Chalker, Samantha A.; Carmel, Adam; Atkins, David C.; Landes, Sara J.; Kerbrat, Amanda H.; Comtois, Katherine Anne

2015-01-01

Few studies have examined effects of challenging behaviors of clients with borderline personality disorder (BPD) on psychotherapy outcomes. Dialectical behavior therapy (DBT) is an evidence-based treatment designed to treat chronic suicidality, self-directed violence (SDV), and emotion dysregulation, while targeting challenging behaviors. DBT has been shown to be effective with clients with BPD. We evaluated whether therapist reported challenging behaviors, such as high volume phone contacts or violating the therapist’s limits, during DBT would be associated with dropping out of DBT, severity and frequency of SDV, emotion regulation deficits, and client’s and therapist’s satisfaction of treatment. The current study examined challenging behaviors reported by therapists in a sample of 63 psychiatrically disabled outpatient DBT clients diagnosed with BPD (73% women, average age 37 years). More frequent phone contacts were associated with a decrease in dropout and psychological symptoms, and an increase in client and therapist satisfaction. More avoidance/disengagement behavior was associated with more than twice the risk of SDV and a decrease in therapist satisfaction. Findings suggest that the phone coaching might serve to maximize client satisfaction and reduce the likelihood of dropout. PMID:26496225

Understanding and influencing the stigma of mental illness.

PubMed

Corrigan, Patrick W; Wassel, Abigail

2008-01-01

Life goals and the opportunities that define them are impaired by the stigma of mental illness. Three kinds of stigma may act as barriers to personal aspirations: public stigma, self-stigma, and label avoidance. Challenging mental illness stigm is essential in helping individuals accomplish recovery-related goals. Public stigma may be changed through protest, education, and contact. Self-stigma can be addressed by fostering group identity, changing the perceived legitimacy of stigma through cognitive rehabilitation, and making strategic decisions about disclosing one's mental health history. Stigma change for label avoidance is not as well understood but may include the education and contact approaches used for public stigma. Evidence-based approaches to stigma change need to be substantiated by rigorous investigations.

77 FR 21512 - Approval, Disapproval and Promulgation of Air Quality Implementation Plan; Utah; Maintenance Plan...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-10

... possible, you contact the individual listed in the FOR FURTHER INFORMATION CONTACT section to view the hard copy of the docket. You may view the hard copy of the docket Monday through Friday, 8 a.m. to 4 p.m... your concerns, and suggest alternatives. g. Explain your views as clearly as possible, avoiding the use...

Surface covering of downed logs: drivers of a neglected process in dead wood ecology.

PubMed

Dynesius, Mats; Gibb, Heloise; Hjältén, Joakim

2010-10-07

Many species use coarse woody debris (CWD) and are disadvantaged by the forestry-induced loss of this resource. A neglected process affecting CWD is the covering of the surfaces of downed logs caused by sinking into the ground (increasing soil contact, mostly covering the underside of the log), and dense overgrowth by ground vegetation. Such cover is likely to profoundly influence the quality and accessibility of CWD for wood-inhabiting organisms, but the factors affecting covering are largely unknown. In a five-year experiment we determined predictors of covering rate of fresh logs in boreal forests and clear-cuts. Logs with branches were little covered because they had low longitudinal ground contact. For branchless logs, longitudinal ground contact was most strongly related to estimated peat depth (positive relation). The strongest predictor for total cover of branchless logs was longitudinal ground contact. To evaluate the effect on cover of factors other than longitudinal ground contact, we separately analyzed data from only those log sections that were in contact with the ground. Four factors were prominent predictors of percentage cover of such log sections: estimated peat depth, canopy shade (both increasing cover), potential solar radiation calculated from slope and slope aspect, and diameter of the log (both reducing cover). Peat increased cover directly through its low resistance, which allowed logs to sink and soil contact to increase. High moisture and low temperatures in pole-ward facing slopes and under a canopy favor peat formation through lowered decomposition and enhanced growth of peat-forming mosses, which also proved to rapidly overgrow logs. We found that in some boreal forests, peat and fast-growing mosses can rapidly cover logs lying on the ground. When actively introducing CWD for conservation purposes, we recommend that such rapid covering is avoided, thereby most likely improving the CWD's longevity as habitat for many species.

Partial reinforcement of avoidance and resistance to extinction in humans.

PubMed

Xia, Weike; Dymond, Simon; Lloyd, Keith; Vervliet, Bram

2017-09-01

In anxiety, maladaptive avoidance behavior provides for near-perfect controllability of potential threat. There has been little laboratory-based treatment research conducted on controllability as a contributing factor in the transition from adaptive to maladaptive avoidance. Here, we investigated for the first time whether partial reinforcement rate, or the reliability of avoidance at controlling or preventing contact with an aversive event, influences subsequent extinction of avoidance in humans. Five groups of participants were exposed to different partial reinforcement rates where avoidance cancelled upcoming shock on 100%, 75%, 50%, 25% or 0% of trials. During extinction, all shocks were withheld. Avoidance behavior, online shock expectancy ratings and skin conductance responses (SCRs) were measured throughout. We found that avoidance was a function of relative controllability: higher reinforcement rate groups engaged in significantly more extinction-resistant avoidance than lower reinforcement groups, and shock expectancy was inversely related with reinforcement rate during avoidance acquisition. Partial reinforcement effects were not evident in SCRs. Overall, the current study highlights the clinical relevance of laboratory-based treatment research on partial reinforcement or controllability effects on extinction of avoidance. Copyright © 2017 Elsevier Ltd. All rights reserved.

Roles of endothelial A-type lamins in migration of T cells on and under endothelial layers

NASA Astrophysics Data System (ADS)

Song, Kwang Hoon; Lee, Jaehyun; Park, Hyoungjun; Kim, Hye Mi; Park, Jeehun; Kwon, Keon Woo; Doh, Junsang

2016-03-01

Stiff nuclei in cell-dense microenvironments may serve as distinct biomechanical cues for cell migration, but such a possibility has not been tested experimentally. As a first step addressing this question, we altered nuclear stiffness of endothelial cells (ECs) by reducing the expression of A-type lamins using siRNA, and investigated the migration of T cells on and under EC layers. While most T cells crawling on control EC layers avoided crossing over EC nuclei, a significantly higher fraction of T cells on EC layers with reduced expression of A-type lamins crossed over EC nuclei. This result suggests that stiff EC nuclei underlying T cells may serve as “duro-repulsive” cues to direct T cell migration toward less stiff EC cytoplasm. During subendothelial migration under EC layers with reduced expression of A-type lamins, T cells made prolonged contact and substantially deformed EC nuclei, resulting in reduced speed and directional persistence. This result suggests that EC nuclear stiffness promotes fast and directionally persistent subendothelial migration of T cells by allowing minimum interaction between T cells and EC nuclei.

Profile parameters of wheelset detection for high speed freight train

NASA Astrophysics Data System (ADS)

Yang, Kai; Ma, Li; Gao, Xiaorong; Wang, Li

2012-04-01

Because of freight train, in China, transports goods on railway freight line throughout the country, it does not depart from or return to engine shed during a long phase, thus we cannot monitor the quality of wheel set effectively. This paper provides a system which uses leaser and high speed camera, applies no-contact light section technology to get precise wheel set profile parameters. The paper employs clamping-track method to avoid complex railway ballast modification project. And detailed descript an improved image-tracking algorithm to extract central line from profile curve. For getting one pixel width and continuous line of the profile curve, uses local gray maximum points as direction control points to direct tracking direction. The results based on practical experiment show the system adapted to detection environment of high speed and high vibration, and it can effectively detect the wheelset geometric parameters with high accuracy. The system fills the gaps in wheel set detection for freight train in main line and has an enlightening function on monitoring the quality of wheel set.

Direct Wafer Bonding and Its Application to Waveguide Optical Isolators

PubMed Central

Mizumoto, Tetsuya; Shoji, Yuya; Takei, Ryohei

2012-01-01

This paper reviews the direct bonding technique focusing on the waveguide optical isolator application. A surface activated direct bonding technique is a powerful tool to realize a tight contact between dissimilar materials. This technique has the potential advantage that dissimilar materials are bonded at low temperature, which enables one to avoid the issue associated with the difference in thermal expansion. Using this technique, a magneto-optic garnet is successfully bonded on silicon, III-V compound semiconductors and LiNbO3. As an application of this technique, waveguide optical isolators are investigated including an interferometric waveguide optical isolator and a semileaky waveguide optical isolator. The interferometric waveguide optical isolator that uses nonreciprocal phase shift is applicable to a variety of waveguide platforms. The low refractive index of buried oxide layer in a silicon-on-insulator (SOI) waveguide enhances the magneto-optic phase shift, which contributes to the size reduction of the isolator. A semileaky waveguide optical isolator has the advantage of large fabrication-tolerance as well as a wide operation wavelength range. PMID:28817020

Mechlorethamine Induced Contact Dermatitis Avoidance Study

ClinicalTrials.gov

2017-12-15

Cutaneous T-cell Lymphoma; Cutaneous T-cell Lymphoma Stage I; Mycosis Fungoides; Folliculotropic Mycosis Fungoides; Granulomatous Slack Skin; Syringotropic Mycosis Fungoides; Mycosis Fungoides Variant; Transformed Mycosis Fungoides

The Extended Contact Hypothesis: A Meta-Analysis on 20 Years of Research.

PubMed

Zhou, Shelly; Page-Gould, Elizabeth; Aron, Arthur; Moyer, Anne; Hewstone, Miles

2018-04-01

According to the extended contact hypothesis, knowing that in-group members have cross-group friends improves attitudes toward this out-group. This meta-analysis covers the 20 years of research that currently exists on the extended contact hypothesis, and consists of 248 effect sizes from 115 studies. The aggregate relationship between extended contact and intergroup attitudes was r = .25, 95% confidence interval (CI) = [.22, .27], which reduced to r = .17, 95% CI = [.14, .19] after removing direct friendship's contribution; these results suggest that extended contact's hypothesized relationship to intergroup attitudes is small-to-medium and exists independently of direct friendship. This relationship was larger when extended contact was perceived versus actual, highlighting the importance of perception in extended contact. Current results on extended contact mostly resembled their direct friendship counterparts, suggesting similarity between these contact types. These unique insights about extended contact and its relationship with direct friendship should enrich and spur growth within this literature.

Direct contact as a moderator of extended contact effects: cross-sectional and longitudinal impact on outgroup attitudes, behavioral intentions, and attitude certainty.

PubMed

Christ, Oliver; Hewstone, Miles; Tausch, Nicole; Wagner, Ulrich; Voci, Alberto; Hughes, Joanne; Cairns, Ed

2010-12-01

Cross-group friendships (the most effective form of direct contact) and extended contact (i.e., knowing ingroup members who have outgroup friends) constitute two of the most important means of improving outgroup attitudes. Using cross-sectional and longitudinal samples from different intergroup contexts, this research demonstrates that extended contact is most effective when individuals live in segregated neighborhoods having only few, or no, direct friendships with outgroup members. Moreover, by including measures of attitudes and behavioral intentions the authors showed the broader impact of these forms of contact, and, by assessing attitude certainty as one dimension of attitude strength, they tested whether extended contact can lead not only to more positive but also to stronger outgroup orientations. Cross-sectional data showed that direct contact was more strongly related to attitude certainty than was extended contact, but longitudinal data showed both forms of contact affected attitude certainty in the long run.

Nasally-Administered Oxytocin Has Limited Effects on Owner-Directed Attachment Behavior in Pet Dogs (Canis lupus familiaris)

PubMed Central

Thielke, Lauren E.; Rosenlicht, Giovanna; Saturn, Sarina R.; Udell, Monique A. R.

2017-01-01

The present study explored the effects of intranasal oxytocin, a naturally occurring hormone, on the behavior of pet dogs during an attachment test. Each dog participated in two testing sessions. On one visit saline was administered nasally, and on another, oxytocin was administered nasally. For half of the dogs (n = 20), solutions were administered with a Mucosal Atomization Device (MAD) and for half of the dogs (n = 20), solutions were administered using a nasal spray bottle. Condition order was counterbalanced and a double-blind methodology was employed. Following a 30-min wait period after administration of solutions, dog-owner pairs participated in the Secure Base Test, a short attachment test consisting of three 2-min phases: (1) Baseline- the owner was present, dogs were able to freely explore the testing room (2) Alone- dogs were left alone in the testing room (3) Return- owners re-entered the room and were reunited with their dog. In each phase the dog was evaluated for contact seeking, exploration, and avoidance behaviors. Although, oxytocin administration was expected to increase owner-directed proximity and contact seeking behavior, this effect was not observed. In fact, in the baseline phase, dogs spent significantly more time seeking the proximity of their owners when they received saline than when they received OT (p < 0.05). Sex differences were also assessed for the behavioral variables of interest in the Secure Base Test, and results indicated that OT did not affect dogs' behavior in the alone phase, but when saline was administered, females spent significantly more time in contact with the door than males in the alone phase (p < 0.05). Overall, the effects of nasally administered oxytocin on attachment related behavior appeared to be limited or inconsistent for this pet dog population. PMID:29033879

Investigation of the influence of process parameters on adhesive wear under hot stamping conditions

NASA Astrophysics Data System (ADS)

Schwingenschlögl, P.; Weldi, M.; Merklein, M.

2017-09-01

Current challenges like increasing safety standards and reducing fuel consumption motivate lightweight construction in modern car bodies. Besides using lightweight workpiece materials like aluminum, hot stamping has been established as a key technology for producing safety relevant components. Producing hot stamped parts out of ultra-high strength steels offers the possibility to improve the crash performance. At the same time the weight of car structure is reduced by using thinner sheet thicknesses. In order to avoid oxide scale formation and ensure corrosion protection, AlSi coatings are commonly deposited on the sheet surfaces used for direct hot stamping. This workpiece coating has a critical impact on the tribological conditions within the forming process and, as a consequence, influences the quality of hot stamped parts as well as tool wear. AlSi coatings have been identified as major reason for adhesive wear, which represents the main wear mechanism in hot stamping. Within this study, the influence of the process parameters on adhesive wear are investigated in dependency of workpiece and tool temperatures, drawing velocities and contact pressures. The tribological behavior is analyzed based on strip drawing experiments under direct hot stamping conditions. The experiments are performed with AlSi coated 22MnB5 in contact with the hot working tool steel 1.2367. For analyzing the amount of adhesion on the friction jaws, the surfaces are characterized by optical measurements. The experiments indicate that higher workpiece temperatures cause severe adhesive wear on the tool surface, while an increase of drawing velocity or contact pressure led to reduced adhesion. The measured friction coefficients decreased with rising amount of adhesion and remained at a constant level after a certain adhesive layer was built up on the tool surface.

A Psittacosis Outbreak among English Office Workers with Little or No Contact with Birds, August 2015.

PubMed

Mair-Jenkins, John; Lamming, Tracey; Dziadosz, Andy; Flecknoe, Daniel; Stubington, Thomas; Mentasti, Massimo; Muir, Peter; Monk, Philip

2018-04-27

On 14th August 2015 an office manager informed Public Health England of five employees known to have been diagnosed with pneumonia over the previous three weeks. We investigated to establish whether an outbreak occurred and to identify and control the source of infection. We undertook case finding for self-reported pneumonia cases at local businesses (July-August 2015). Clinical samples from a hospitalised case were tested for common respiratory pathogens, but returned negative results. Further testing confirmed Chlamydia psittaci infection in this case (serology and PCR).  We subsequently undertook C. psittaci testing for all cases, redefining them as confirmed ( C. psittaci PCR or high antibody titre via serology) or probable (inconclusive C. psittaci serology). Twenty-eight day exposure histories informed descriptive epidemiological analysis. We conducted an environmental investigation at the office to identify potential sources of exposure. We identified six office workers with pneumonia; four met case definitions (three confirmed, one probable) with symptom onset between 29th July and 4th August 2015. Workplace was the only epidemiological link and only one case reported limited, indirect bird contact. Environmental investigations identified pigeons roosting near the office which were being fed by workers (none cases). This was a probable outbreak of psittacosis with no direct bird-to-human contact reported. Cases recovered after receiving appropriate antibiotics. Feeding of pigeons was stopped. A deep clean of office ventilation systems was conducted and workers were advised to avoid bird contact.  We hypothesised that indirect environmental exposure to infected pigeons was to the source of this outbreak. This work provides evidence that health professionals should consider psittacosis in the differential diagnosis of cases of severe or atypical respiratory illness even without overt bird contact.

Controlling direct contact force for wet adhesion with different wedged film stabilities

NASA Astrophysics Data System (ADS)

Li, Meng; Xie, Jun; Shi, Liping; Huang, Wei; Wang, Xiaolei

2018-04-01

In solid–liquid–solid adhesive systems, wedged films often feature instability at microscopic thicknesses, which can easily disrupt the adhesive strength of their remarkable direct contact force. Here, sodium dodecyl sulfate (SDS) was employed to tune the instability of adhesion in wedged glass–water–rubber films, achieving controllable direct contact. Experimental results showed that the supplement of SDS molecules significantly weakened the direct contact force for wet adhesion and eliminated it at high concentrations. The underlying reason was suggested to be the repulsive double-layer force caused by SDS molecules, which lowers the instability of the wedged film and balances the preload, disrupting the direct contact in wet adhesion.

Protein contact dermatitis: allergens, pathogenesis, and management.

PubMed

Levin, Cheryl; Warshaw, Erin

2008-01-01

Protein contact dermatitis is an allergic skin reaction induced principally by proteins of either animal or plant origin. The clinical presentation is that of a chronic dermatitis, and it is often difficult to differentiate between allergic contact dermatitis and other eczematous dermatoses. One distinguishing clinical feature is that acute flares of pruritus, urticaria, edema, or vesiculation are noted minutes after contact with the causative substances. Additionally, the patch-test result is typically negative, and the scratch- or prick-test result is positive. The pathogenesis of protein contact dermatitis is unclear but may involve a type I (immunoglobulin E [IgE], immediate) hypersensitivity reaction, type IV (cell-mediated delayed) hypersensitivity reaction, and/or a delayed reaction due to IgE-bearing Langerhans' cells. Management involves avoidance of the allergen.

Comparison of nickel silicide and aluminium ohmic contact metallizations for low-temperature quantum transport measurements

PubMed Central

2011-01-01

We examine nickel silicide as a viable ohmic contact metallization for low-temperature, low-magnetic-field transport measurements of atomic-scale devices in silicon. In particular, we compare a nickel silicide metallization with aluminium, a common ohmic contact for silicon devices. Nickel silicide can be formed at the low temperatures (<400°C) required for maintaining atomic precision placement in donor-based devices, and it avoids the complications found with aluminium contacts which become superconducting at cryogenic measurement temperatures. Importantly, we show that the use of nickel silicide as an ohmic contact at low temperatures does not affect the thermal equilibration of carriers nor contribute to hysteresis in a magnetic field. PMID:21968083

Photo-stimulated low electron temperature high current diamond film field emission cathode

DOEpatents

Shurter,; Roger Philips, Devlin [Los Alamos, NM; David James, Moody [Santa Fe, NM; Nathan Andrew, Taccetti [Los Alamos, NM; Jose Martin, Russell [Santa Fe, NM; John, Steven [Los Alamos, NM

2012-07-24

An electron source includes a back contact surface having a means for attaching a power source to the back contact surface. The electron source also includes a layer comprising platinum in direct contact with the back contact surface, a composite layer of single-walled carbon nanotubes embedded in platinum in direct contact with the layer comprising platinum. The electron source also includes a nanocrystalline diamond layer in direct contact with the composite layer. The nanocrystalline diamond layer is doped with boron. A portion of the back contact surface is removed to reveal the underlying platinum. The electron source is contained in an evacuable container.

All diamond self-aligned thin film transistor

DOEpatents

Gerbi, Jennifer [Champaign, IL

2008-07-01

A substantially all diamond transistor with an electrically insulating substrate, an electrically conductive diamond layer on the substrate, and a source and a drain contact on the electrically conductive diamond layer. An electrically insulating diamond layer is in contact with the electrically conductive diamond layer, and a gate contact is on the electrically insulating diamond layer. The diamond layers may be homoepitaxial, polycrystalline, nanocrystalline or ultrananocrystalline in various combinations.A method of making a substantially all diamond self-aligned gate transistor is disclosed in which seeding and patterning can be avoided or minimized, if desired.

78 FR 41307 - Approval and Promulgation of Air Quality Implementation Plans; State of Colorado; Second Ten-Year...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-10

... contact the individual listed in the FOR FURTHER INFORMATION CONTACT section to view the hard copy of the docket. You may view the hard copy of the docket Monday through Friday, 8:00 a.m. to 4:00 p.m., excluding..., and suggest alternatives. g. Explain your views as clearly as possible, avoiding the use of profanity...

Relationship between Personality Traits and Endogenous Analgesia: The Role of Harm Avoidance.

PubMed

Nahman-Averbuch, Hadas; Yarnitsky, David; Sprecher, Elliot; Granovsky, Yelena; Granot, Michal

2016-01-01

Whether psychological factors such as anxiety and pain catastrophizing levels influence the expression of endogenous analgesia in general and, more specifically, the conditioned pain modulation (CPM) response is still under debate. It may be assumed that other psychological characteristics also play a role in the CPM response. The neurotransmitters serotonin, dopamine, and norepinephrine are involved both in CPM, as well as personality traits such as harm avoidance (HA), novelty seeking (NS), and reward dependence (RD), which can be obtained by the Tridimensional Personality Questionnaire (TPQ). However, the associations between these traits (HA, NS, and RD) with endogenous analgesia revealed by CPM have not yet been explored. Healthy middle-age subjects (n = 28) completed the TPQ, Spielberger's State Anxiety Inventory, and the Pain Catastrophizing Scale and were assessed for CPM paradigms using thermal phasic temporal summation as the "test stimulus" and hand immersion into hot water bath (CPM water) or contact heat (CPM contact) for "conditioning stimulus." Higher levels of HA were associated with less-efficient CPM responses obtained by both paradigms: CPM water (r = 0.418, P = 0.027) and CPM contact (r = 0.374, P = 0.050). However, NS and RD were not associated with the other measurements. No significant relationship was observed between state anxiety and pain catastrophizing levels and the CPM responses. The relationship between the capacity of endogenous analgesia and the tendency to avoid aversive experience can be explained by mutual mechanisms involving similar neurotransmitters or brain areas. These findings illuminate the key role of harm avoidance obtained by the TPQ in determining the characteristics of pain modulation profile. © 2014 World Institute of Pain.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Jaehong; Reid, Obadiah G.; Blackburn, Jeffrey L.

The strong quantum confinement and low dielectric screening impart single-walled carbon nanotubes with exciton-binding energies substantially exceeding kBT at room temperature. Despite these large binding energies, reported photoluminescence quantum yields are typically low and some studies suggest that photoexcitation of carbon nanotube excitonic transitions can produce free charge carriers. Here we report the direct measurement of long-lived free-carrier generation in chirality-pure, single-walled carbon nanotubes in a low dielectric solvent. Time-resolved microwave conductivity enables contactless and quantitative measurement of the real and imaginary photoconductance of individually suspended nanotubes. We found that the conditions of the microwave conductivity measurement allow us tomore » avoid the complications of most previous measurements of nanotube free-carrier generation, including tube–tube/tube–electrode contact, dielectric screening by nearby excitons and many-body interactions. At low photon fluence (approximately 0.05 excitons per μm length of tubes), we directly observe free carriers on excitation of the first and second carbon nanotube exciton transitions.« less

Hadoop-BAM: directly manipulating next generation sequencing data in the cloud

PubMed Central

Niemenmaa, Matti; Kallio, Aleksi; Schumacher, André; Klemelä, Petri; Korpelainen, Eija; Heljanko, Keijo

2012-01-01

Summary: Hadoop-BAM is a novel library for the scalable manipulation of aligned next-generation sequencing data in the Hadoop distributed computing framework. It acts as an integration layer between analysis applications and BAM files that are processed using Hadoop. Hadoop-BAM solves the issues related to BAM data access by presenting a convenient API for implementing map and reduce functions that can directly operate on BAM records. It builds on top of the Picard SAM JDK, so tools that rely on the Picard API are expected to be easily convertible to support large-scale distributed processing. In this article we demonstrate the use of Hadoop-BAM by building a coverage summarizing tool for the Chipster genome browser. Our results show that Hadoop offers good scalability, and one should avoid moving data in and out of Hadoop between analysis steps. Availability: Available under the open-source MIT license at http://sourceforge.net/projects/hadoop-bam/ Contact: matti.niemenmaa@aalto.fi Supplementary information: Supplementary material is available at Bioinformatics online. PMID:22302568

Photoinduced Spontaneous Free-Carrier Generation in Semiconducting Single-Walled Carbon Nanotubes

DOE PAGES

Park, Jaehong; Reid, Obadiah G.; Blackburn, Jeffrey L.; ...

2015-11-04

The strong quantum confinement and low dielectric screening impart single-walled carbon nanotubes with exciton-binding energies substantially exceeding kBT at room temperature. Despite these large binding energies, reported photoluminescence quantum yields are typically low and some studies suggest that photoexcitation of carbon nanotube excitonic transitions can produce free charge carriers. Here we report the direct measurement of long-lived free-carrier generation in chirality-pure, single-walled carbon nanotubes in a low dielectric solvent. Time-resolved microwave conductivity enables contactless and quantitative measurement of the real and imaginary photoconductance of individually suspended nanotubes. We found that the conditions of the microwave conductivity measurement allow us tomore » avoid the complications of most previous measurements of nanotube free-carrier generation, including tube–tube/tube–electrode contact, dielectric screening by nearby excitons and many-body interactions. At low photon fluence (approximately 0.05 excitons per μm length of tubes), we directly observe free carriers on excitation of the first and second carbon nanotube exciton transitions.« less

Contact Dermatitis for the Practicing Allergist.

PubMed

Bernstein, David I

2015-01-01

This article provides an overview of important practice recommendations from the recently updated Contact Dermatitis Practice Parameter. This updated parameter provides essential recommendations pertaining to clinical history, physical examination, and patch testing evaluation of patients suspected of allergic contact dermatitis. In addition to providing guidance for performing and interpreting closed patch testing, the updated parameter provides concrete recommendations for assessing metal hypersensitivity in patients receiving prosthetic devices, for evaluating workers with occupational contact dermatitis, and also for addressing allergic contact dermatitis in children. Finally, the document provides practical recommendations useful for educating patients regarding avoidance of exposure to known contact sensitizers in the home and at work. The Contact Dermatitis Parameter is designed as a practical, evidence-based clinical tool to be used by allergists and dermatologists who routinely are called upon to evaluate patients with skin disorders. Copyright © 2015 American Academy of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

Reasons to Do Food Challenges

MedlinePlus

... than was previously suspected. In this case, the importance of strict avoidance, as well as being thoroughly prepared to treat severe ... & Science Education & Training Contact Us Make a Donation Make an ...

Informing disease models with temporal and spatial contact structure among GPS-collared individuals in wild populations.

PubMed

Williams, David M; Dechen Quinn, Amy C; Porter, William F

2014-01-01

Contacts between hosts are essential for transmission of many infectious agents. Understanding how contacts, and thus transmission rates, occur in space and time is critical to effectively responding to disease outbreaks in free-ranging animal populations. Contacts between animals in the wild are often difficult to observe or measure directly. Instead, one must infer contacts from metrics such as proximity in space and time. Our objective was to examine how contacts between white-tailed deer (Odocoileus virginianus) vary in space and among seasons. We used GPS movement data from 71 deer in central New York State to quantify potential direct contacts between deer and indirect overlap in space use across time and space. Daily probabilities of direct contact decreased from winter (0.05-0.14), to low levels post-parturition through summer (0.00-0.02), and increased during the rut to winter levels. The cumulative distribution for the spatial structure of direct and indirect contact probabilities around a hypothetical point of occurrence increased rapidly with distance for deer pairs separated by 1,000 m-7,000 m. Ninety-five percent of the probabilities of direct contact occurred among deer pairs within 8,500 m of one another, and 99% within 10,900 m. Probabilities of indirect contact accumulated across greater spatial extents: 95% at 11,900 m and 99% at 49,000 m. Contacts were spatially consistent across seasons, indicating that although contact rates differ seasonally, they occur proportionally across similar landscape extents. Distributions of contact probabilities across space can inform management decisions for assessing risk and allocating resources in response.

Knee Muscular Control During Jump Landing in Multidirections.

PubMed

Sinsurin, Komsak; Vachalathiti, Roongtiwa; Jalayondeja, Wattana; Limroongreungrat, Weerawat

2016-06-01

Jump landing is a complex movement in sports. While competing and practicing, athletes frequently perform multi-planar jump landing. Anticipatory muscle activity could influence the amount of knee flexion and prepare the knee for dynamic weight bearing such as landing tasks. The aim of the present study was to examine knee muscle function and knee flexion excursion as athletes naturally performed multi-direction jump landing. Eighteen male athletes performed the jump-landing test in four directions: forward (0°), 30° diagonal, 60° diagonal, and lateral (90°). Muscles tested were vastus medialis (VM), vastus lateralis (VL), rectus femoris (RF), semitendinosus (ST), and biceps femoris (BF). A Vicon(TM) 612 workstation collected the kinematic data. An electromyography was synchronized with the Vicon(TM) Motion system to quantify dynamic muscle function. Repeated measure ANOVA was used to analyze the data. Jump-landing direction significantly influenced (P < 0.05) muscle activities of VL, RF, and ST and knee flexion excursion. Jumpers landed with a trend of decreasing knee flexion excursion and ST muscle activity 100 ms before foot contact progressively from forward to lateral directions of jump landing. A higher risk of knee injury might occur during lateral jump landing than forward and diagonal directions. Athletes should have more practice in jump landing in lateral direction to avoid injury. Landing technique with high knee flexion in multi-directions should be taught to jumpers for knee injury prevention.

A heater made from graphite composite material for potential deicing application

NASA Technical Reports Server (NTRS)

Hung, C. C.; Stahl, M.; Stahl, M.; Stahl, M.

1986-01-01

A surface heater was developed using a graphite fiber-epoxy composite as the heating element. This heater can be thin, highly electrically and thermally conductive, and can conform to an irregular surface. Therefore it may be used in an aircraft's thermal deicing system to quickly and uniformly heat the aircraft surface. One-ply of unidirectional graphite fiber-epoxy composite was laminated between two plies of fiber glass-epoxy composite, with nickel foil contacting the end portions of the composite and partly exposed beyond the composites for electrical contact. The model heater used brominated P-100 fibers from Amoco. The fiber's electrical resistivity, thermal conductivity and density were 50 micro ohms per centimeter, 270 W/m-K and 2.30 gm/cubic cm, respectively. The electricity was found to penetrate through the composite in the transverse direction to make an acceptably low foil-composite contact resistance. When conducting current, the heater temperature increase reached 50 percent of the steady state value within 20 sec. There was no overheating at the ends of the heater provided there was no water corrosion. If the foil-composite bonding failed during storage, liquid water exposure was found to oxidize the foil. Such bonding failure may be avoided if perforated nickel foil is used, so that the composite plies can bond to each other through the perforated holes and therefore lock the foil in place.

Human symbionts inject and neutralize antibacterial toxins to persist in the gut.

PubMed

Wexler, Aaron G; Bao, Yiqiao; Whitney, John C; Bobay, Louis-Marie; Xavier, Joao B; Schofield, Whitman B; Barry, Natasha A; Russell, Alistair B; Tran, Bao Q; Goo, Young Ah; Goodlett, David R; Ochman, Howard; Mougous, Joseph D; Goodman, Andrew L

2016-03-29

The human gut microbiome is a dynamic and densely populated microbial community that can provide important benefits to its host. Cooperation and competition for nutrients among its constituents only partially explain community composition and interpersonal variation. Notably, certain human-associated Bacteroidetes--one of two major phyla in the gut--also encode machinery for contact-dependent interbacterial antagonism, but its impact within gut microbial communities remains unknown. Here we report that prominent human gut symbionts persist in the gut through continuous attack on their immediate neighbors. Our analysis of just one of the hundreds of species in these communities reveals 12 candidate antibacterial effector loci that can exist in 32 combinations. Through the use of secretome studies, in vitro bacterial interaction assays and multiple mouse models, we uncover strain-specific effector/immunity repertoires that can predict interbacterial interactions in vitro and in vivo, and find that some of these strains avoid contact-dependent killing by accumulating immunity genes to effectors that they do not encode. Effector transmission rates in live animals can exceed 1 billion events per minute per gram of colonic contents, and multiphylum communities of human gut commensals can partially protect sensitive strains from these attacks. Together, these results suggest that gut microbes can determine their interactions through direct contact. An understanding of the strategies human gut symbionts have evolved to target other members of this community may provide new approaches for microbiome manipulation.

Direct and extended intergenerational contact and young people's attitudes towards older adults.

PubMed

Drury, Lisbeth; Hutchison, Paul; Abrams, Dominic

2016-09-01

Research suggests that positive intergenerational contact can improve young people's attitudes towards older adults. However, today's age-segregated society may not provide ample opportunities for positive contact between younger and older adults to occur on a regular basis. In three studies, we investigated whether the positive attitudinal outcomes associated with direct contact might also stem from a more indirect form of intergenerational relationship: extended contact. In Study 1 (N = 70), extended contact was associated with more positive attitudes towards older adults even when controlling for direct intergenerational contact (contact frequency and contact quality). In Study 2 (N = 110), the positive effects of direct and extended contact on young people's age-related attitudes were mediated by reductions in intergroup anxiety and ageing anxiety. The mediational effects of intergroup anxiety were replicated in Study 3 (N = 95) and ingroup norms additionally emerged as a mediator of the positive effects of extended contact on young people's attitudes towards older adults. Discussion focuses on the implications for strategies aimed at tackling ageism. ©2016 The Authors. British Journal of Social Psychology published by John Wiley & Sons Ltd on behalf of British Psychological Society.

Stopping the Bottle

MedlinePlus

... difficult it can be to break the bottle habit. Longer bottle use may lead to cavities or ... Drinks for Kids Toddlers at the Table: Avoiding Power Struggles View more About Us Contact Us Partners ...

Parinaud oculoglandular syndrome

MedlinePlus

... most common causes are cat scratch disease and tularemia (rabbit fever). The bacteria that cause either condition ... cat, even a healthy cat. You can avoid tularemia by not having contact with wild rabbits, squirrels, ...

Gradient, contact-free volume transfers minimize compound loss in dose-response experiments.

PubMed

Harris, David; Olechno, Joe; Datwani, Sammy; Ellson, Richard

2010-01-01

More accurate dose-response curves can be constructed by eliminating aqueous serial dilution of compounds. Traditional serial dilutions that use aqueous diluents can result in errors in dose-response values of up to 4 orders of magnitude for a significant percentage of a compound library. When DMSO is used as the diluent, the errors are reduced but not eliminated. The authors use acoustic drop ejection (ADE) to transfer different volumes of model library compounds, directly creating a concentration gradient series in the receiver assay plate. Sample losses and contamination associated with compound handling are therefore avoided or minimized, particularly in the case of less water-soluble compounds. ADE is particularly well suited for assay miniaturization, but gradient volume dispensing is not limited to miniaturized applications.

Rugged fiber optic probe for raman measurement

DOEpatents

O'Rourke, Patrick E.; Toole, Jr., William R.; Nave, Stanley E.

1998-01-01

An optical probe for conducting light scattering analysis is disclosed. The probe comprises a hollow housing and a probe tip. A fiber assembly made up of a transmitting fiber and a receiving bundle is inserted in the tip. A filter assembly is inserted in the housing and connected to the fiber assembly. A signal line from the light source and to the spectrometer also is connected to the filter assembly and communicates with the fiber assembly. By using a spring-loaded assembly to hold the fiber connectors together with the in-line filters, complex and sensitive alignment procedures are avoided. The close proximity of the filter assembly to the probe tip eliminates or minimizes self-scattering generated by the optical fiber. Also, because the probe can contact the sample directly, sensitive optics can be eliminated.

Semitransparent Fully Air Processed Perovskite Solar Cells.

PubMed

Bu, Lingling; Liu, Zonghao; Zhang, Meng; Li, Wenhui; Zhu, Aili; Cai, Fensha; Zhao, Zhixin; Zhou, Yinhua

2015-08-19

Semitransparent solar cells are highly attractive for application as power-generating windows. In this work, we present semitransparent perovskite solar cells that employ conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) ( PSS) film as the transparent counter electrode. The PSS electrode is prepared by transfer lamination technique using plastic wrap as the transfer medium. The use of the transfer lamination technique avoids the damage of the CH3NH3PbI3 perovskite film by direct contact of PSS aqueous solution. The semitransparent perovskite solar cells yield a power conversion efficiency of 10.1% at an area of about 0.06 cm(2) and 2.9% at an area of 1 cm(2). The device structure and the fabrication technique provide a facile way to produce semitransparent perovskite solar cells.

Use of aluminum phosphate as the dehydration catalyst in single step dimethyl ether process

DOEpatents

Peng, Xiang-Dong; Parris, Gene E.; Toseland, Bernard A.; Battavio, Paula J.

1998-01-01

The present invention pertains to a process for the coproduction of methanol and dimethyl ether (DME) directly from a synthesis gas in a single step (hereafter, the "single step DME process"). In this process, the synthesis gas comprising hydrogen and carbon oxides is contacted with a dual catalyst system comprising a physical mixture of a methanol synthesis catalyst and a methanol dehydration catalyst. The present invention is an improvement to this process for providing an active and stable catalyst system. The improvement comprises the use of an aluminum phosphate based catalyst as the methanol dehydration catalyst. Due to its moderate acidity, such a catalyst avoids the coke formation and catalyst interaction problems associated with the conventional dual catalyst systems taught for the single step DME process.

37 CFR 10.33 - Direct contact with prospective clients.

Code of Federal Regulations, 2012 CFR

2012-07-01

... TRADEMARK OFFICE, DEPARTMENT OF COMMERCE REPRESENTATION OF OTHERS BEFORE THE PATENT AND TRADEMARK OFFICE Patent and Trademark Office Code of Professional Responsibility § 10.33 Direct contact with prospective... 37 Patents, Trademarks, and Copyrights 1 2012-07-01 2012-07-01 false Direct contact with...

Scabies: Prevention and Control

MedlinePlus

... and General Public. Contact Us Parasites Home Prevention & Control Recommend on Facebook Tweet Share Compartir When a ... avoid outbreaks. Institutional outbreaks can be difficult to control and require a rapid, aggressive, and sustained response. ...

Neuronal and non-neuronal signals regulate Caernorhabditis elegans avoidance of contaminated food.

PubMed

Anderson, Alexandra; McMullan, Rachel

2018-07-19

One way in which animals minimize the risk of infection is to reduce their contact with contaminated food. Here, we establish a model of pathogen-contaminated food avoidance using the nematode worm Caernorhabditis elegans We find that avoidance of pathogen-contaminated food protects C. elegans from the deleterious effects of infection and, using genetic approaches, demonstrate that multiple sensory neurons are required for this avoidance behaviour. In addition, our results reveal that the avoidance of contaminated food requires bacterial adherence to non-neuronal cells in the tail of C. elegans that are also required for the cellular immune response. Previous studies in C. elegans have contributed significantly to our understanding of molecular and cellular basis of host-pathogen interactions and our model provides a unique opportunity to gain basic insights into how animals avoid contaminated food.This article is part of the Theo Murphy meeting issue 'Evolution of pathogen and parasite avoidance behaviours'. © 2018 The Authors.

Effects of solar cell environment on contact integrity

NASA Technical Reports Server (NTRS)

Weizer, Victor G.; Fatemi, Navid S.

1993-01-01

The III-V semiconductors react extremely rapidly with most commonly used contact metallizations. This precludes the use of elevated temperatures in the contact formation process for solar cells and other shallow junction devices. These devices must rely upon contact metallizations that are sufficiently conductive in their 'as-fabricated' state. However, while there are a number of non-sintered metallizations that have acceptable characteristics, the lack of a sintering step makes them vulnerable to a variety of environmentally induced degradation processes. The degrading effects resulting from the exposure of unsintered devices to a humid environment and to a vacuum (space) environment are described. It is shown, further, that these effects are magnified by the presence of mechanical damage in the contact metallization. The means to avoid or prevent these degrading interactions are presented.

Informing Disease Models with Temporal and Spatial Contact Structure among GPS-Collared Individuals in Wild Populations

PubMed Central

Williams, David M.; Dechen Quinn, Amy C.; Porter, William F.

2014-01-01

Contacts between hosts are essential for transmission of many infectious agents. Understanding how contacts, and thus transmission rates, occur in space and time is critical to effectively responding to disease outbreaks in free-ranging animal populations. Contacts between animals in the wild are often difficult to observe or measure directly. Instead, one must infer contacts from metrics such as proximity in space and time. Our objective was to examine how contacts between white-tailed deer (Odocoileus virginianus) vary in space and among seasons. We used GPS movement data from 71 deer in central New York State to quantify potential direct contacts between deer and indirect overlap in space use across time and space. Daily probabilities of direct contact decreased from winter (0.05–0.14), to low levels post-parturition through summer (0.00–0.02), and increased during the rut to winter levels. The cumulative distribution for the spatial structure of direct and indirect contact probabilities around a hypothetical point of occurrence increased rapidly with distance for deer pairs separated by 1,000 m – 7,000 m. Ninety-five percent of the probabilities of direct contact occurred among deer pairs within 8,500 m of one another, and 99% within 10,900 m. Probabilities of indirect contact accumulated across greater spatial extents: 95% at 11,900 m and 99% at 49,000 m. Contacts were spatially consistent across seasons, indicating that although contact rates differ seasonally, they occur proportionally across similar landscape extents. Distributions of contact probabilities across space can inform management decisions for assessing risk and allocating resources in response. PMID:24409293

Risk and Prevention of Aspergillosis

MedlinePlus

... respirators . Avoid activities that involve close contact to soil or dust, such as yard work or gardening. ... areas. Wear gloves when handling materials such as soil, moss, or manure. To reduce the chances of ...

How to avoid exercise injuries

MedlinePlus

... higher-impact activities like running or aerobics. Contact sports like soccer or basketball are also more likely ... your risk of injury. Safety equipment for your sport may include: Footwear Helmets Mouth guards Goggles Shin ...

Contact lens complications.

PubMed

Suchecki, Jeanine K; Donshik, Peter; Ehlers, William H

2003-09-01

Complications associated with contact lenses range from mild to severe and occur with all lens modalities. Contact lens wear can cause a change in corneal physiology, which can lead to epithelial, stromal, and endothelial compromise. Other complications include lens deposition, allergic conjunctivitis, giant papillary conjunctivitis, peripheral infiltrates, microbial keratitis, and neovascularization. Pre-existing conditions can contribute to these complications, or they can occur in association with contact lens wear and care regimens. Patient-related factors, such as alteration of the recommended wearing or replacement schedules and noncompliance with recommended contact lens care regimens for economic reasons, convenience, or in error, contribute to contact lens-related complications and have led to difficulty in accurate determination of complication rates among the various lens wear modalities. Complications may require discontinuation of contact lenses, topical therapy, and changes in contact lens wearing schedules, materials, and care solutions. On initial lens fitting and follow-up evaluations, practitioners should review contact lens replacement and cleaning regimens with patients and discuss complications. To avoid serious complications, patients should be reminded to remove their contact lenses as soon as ocular irritation occurs, and to call their eye care practitioner immediately if symptoms persist.

Accurate pre-surgical determination for self-drilling miniscrew implant placement using surgical guides and cone-beam computed tomography.

PubMed

Miyazawa, Ken; Kawaguchi, Misuzu; Tabuchi, Masako; Goto, Shigemi

2010-12-01

Miniscrew implants have proven to be effective in providing absolute orthodontic anchorage. However, as self-drilling miniscrew implants have become more popular, a problem has emerged, i.e. root contact, which can lead to perforation and other root injuries. To avoid possible root damage, a surgical guide was fabricated and cone-beam computed tomography (CBCT) was used to incorporate guide tubes drilled in accordance with the planned direction of the implants. Eighteen patients (5 males and 13 females; mean age 23.8 years; minimum 10.7, maximum 45.5) were included in the study. Forty-four self-drilling miniscrew implants (diameter 1.6, and length 8 mm) were placed in interradicular bone using a surgical guide procedure, the majority in the maxillary molar area. To determine the success rates, statistical analysis was undertaken using Fisher's exact probability test. CBCT images of post-surgical self-drilling miniscrew implant placement showed no root contact (0/44). However, based on CBCT evaluation, it was necessary to change the location or angle of 52.3 per cent (23/44) of the guide tubes prior to surgery in order to obtain optimal placement. If orthodontic force could be applied to the screw until completion of orthodontic treatment, screw anchorage was recorded as successful. The total success rate of all miniscrews was 90.9 per cent (40/44). Orthodontic self-drilling miniscrew implants must be inserted carefully, particularly in the case of blind placement, since even guide tubes made on casts frequently require repositioning to avoid the roots of the teeth. The use of surgical guides, fabricated using CBCT images, appears to be a promising technique for placement of orthodontic self-drilling miniscrew implants adjacent to the dental roots and maxillary sinuses.

[Contact lenses for children. Indications and results].

PubMed

Steinbach, P D; Nover, A

1976-03-18

If it is necessary to prescribe contact lenses for children, this correction should be made as soon as possible. As a consequence of the development of soft (hydrophile) lenses, the above mentioned group of patients has increased considerably. In any case, a monolateral aphakia as well as a manifest anisometropia should be corrected by a contact lense to avoid amblyopia, heterotropia and loss of stereoscopic vision. Usually soft lenses are well tolerated, so that patients suffering from aphakia as well as hyperopia should always use this type of lense. Nevertheless, the hard lense still has its indication in treating myopia and high astigmatism.

Comparison of self-reported and observed water contact in an S. mansoni endemic village in Brazil.

PubMed

Friedman, J F; Kurtis, J D; McGarvey, S T; Fraga, A L; Silveira, A; Pizziolo, V; Gazzinelli, G; LoVerde, P; Corrêa-Oliveira, R

2001-03-30

Estimates of exposure are critical for immuno-epidemiologic and intervention studies in human schistosomiasis. Direct observation of human water contact patterns is both costly and time consuming. To address these issues, we determined whether individuals residing in a Schistosoma mansoni endemic village in Brazil could accurately self-report their water contact patterns. We compared the results of a water contact questionnaire to the present gold standard, direct observation of water contact in 86 volunteers, aged 8--29. We administered a survey to estimate volunteers' frequency and type of water contact and directly measured each volunteers' water contact patterns during 5 weeks of detailed water contact observations. We found a poor correlation between self reported frequency of contact and directly observed exposure (rho=0.119, P=NS). The questionnaire data was supplemented by information about average body surface area of exposure and duration of contact for specific activities derived from observations of this cohort. This 'supplemented questionnaire' data was significantly correlated with their exposure index (rho=0.227, P=0.05). It provides a starting point from which questionnaires may develop to provide a more cost-effective and less labor intensive method of assessing water contact exposure at the level of the individual.

Ventrogluteal versus dorsogluteal site selection: A cross-sectional study of muscle and subcutaneous fat thicknesses and an algorithm incorporating demographic and anthropometric data to predict injection outcome.

PubMed

Larkin, Theresa A; Ashcroft, Elfriede; Elgellaie, Asmahan; Hickey, Blake A

2017-06-01

The dorsogluteal and ventrogluteal intramuscular injection sites both have their use in clinical practice; however, it has not been established in whom one or the other should be preferentially targeted or avoided. There is a need for an evidence-based approach towards site selection for a successful intramuscular injection outcome and to avoid unwanted injection outcomes of inadvertent subcutaneous injection or bone contact. Injection outcome is dependent on injection site subcutaneous fat thickness and muscle thickness; these are likely influenced by gender and anthropometry. To determine whether subcutaneous fat, muscle, and total tissue thicknesses differ between the dorsogluteal and ventrogluteal sites, and whether theoretical injection outcome (intramuscular, subcutaneous, or bone contact) can be predicted by demographic and anthropometric data and described by an algorithm. Cross-sectional study design. University in Australia. 145 volunteers (57% female) of at least 18 years of age recruited through the university community. Anthropometric data was collected and subcutaneous fat and muscle thicknesses were quantified by ultrasonography. Anthropometric differences between theoretical injection outcome groups (bone contact versus intramuscular versus subcutaneous at the ventrogluteal and dorsogluteal sites) was determined for each gender (ANOVA). Multiple regression analysis was conducted to determine the influence of demographic and anthropometric data on theoretical intramuscular injection outcome. An algorithm to guide site selection was developed for each gender, based on the anthropometric measures that best discriminated between injection outcomes. Subcutaneous fat, muscle and total tissue were significantly thicker at the dorsogluteal site than the ventrogluteal site, and subcutaneous fat was significantly thicker in females than males at both sites (all p<0.001); there was no gender difference for muscle or total tissue thickness at either site. Female gender, and waist and hip circumference were significant predictors of subcutaneous fat thickness at both sites; male gender was a significant predictor of dorsogluteal site muscle thickness (all p<0.05). In the algorithm developed for site selection based on theoretical injection outcome, the best discriminators were: weight, BMI and waist circumference for females, and weight and distance between the iliac tubercle and anterior superior iliac spine for males. The algorithm describes when each of the ventrogluteal and dorsogluteal sites is appropriate or should be avoided, based on easily obtained anthropometric data. This has direct relevance in clinical practice in evidence-based site selection for gluteal intramuscular injections for optimal medication and health outcomes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Prenatal Care

MedlinePlus

... and prescription medicines you are using. These include dietary or herbal supplements. Some medicines are not safe during pregnancy. At the same time, stopping medicines you need also can be harmful. Avoid contact with toxic substances or materials at ...

Head Lice: Prevention and Control

MedlinePlus

... and General Public. Contact Us Parasites Home Prevention & Control Language: English (US) Español (Spanish) Recommend on Facebook ... that can be taken to help prevent and control the spread of head lice: Avoid head-to- ...

Wild bearded capuchins process cashew nuts without contacting caustic compounds.

PubMed

Sirianni, Giulia; Visalberghi, Elisabetta

2013-04-01

Complex and flexible food processing was a key element for the evolutionary success of hominins, enlarging the range of exploitable foods while enabling occupation of new habitats. Only a few primate species crack open encased food by using percussive tools and/or avoid physical contact with irritant compounds by removing the structures containing them. We describe, for the first time, how a population of bearded capuchin monkeys (Sapajus libidinosus) accesses the nutritious kernel of cashew nuts avoiding the caustic chemicals protecting it. Two processing strategies, namely rubbing/piercing and stone tool use, are used according to maturity of the nuts. The frequency of cashew nuts processing increases with capuchin age, and the same set of processing strategies appears to be absent in other capuchin populations, making cashew nuts processing an excellent candidate for social transmission. © 2013 Wiley Periodicals, Inc.

Contact Burn with Blister Formation in Children Treated with Sennosides.

PubMed

Cogley, Kimberly; Echevarria, Andrea; Correa, Catalina; De la Torre-Mondragón, Luis

2017-03-01

Eight children treated for severe constipation with sennosides unexpectedly developed contact burns with blisters secondary to the use of these laxatives. All patients wore diapers, and the injuries occurred overnight. To avoid this side effect, we recommend that patients treated with sennosides, especially those in diapers, receive the medication at a time that allows for bowel movements to occur during the day and not overnight. © 2017 Wiley Periodicals, Inc.

Introduced Goldfish Affect Amphibians through Inhibition of Sexual Behaviour in Risky Habitats: an Experimental Approach

PubMed Central

Winandy, Laurane; Denoël, Mathieu

2013-01-01

The introduction of alien species is one of the major causes of current and global biodiversity loss. The introduction of fish can be a particular threat to native amphibian populations, which are declining worldwide. One way for amphibians to persist in such altered environments is to adopt anti-predator strategies especially at the behavioural level. However, although it has been shown that avoidance behaviour may decrease the probability of being detected by a potential predator, little is known on the consequences on sexual behaviour. In this study, we tested the hypothesis that adult Alpine newts (Ichthyosaura alpestris) use shelters more often and exhibit less sexual activity in the presence of goldfish (Carassius auratus) and that they reduce sexual activity more in risky micro-habitats than in safe environments. To this end, we assessed behavioural patterns of adult newts in a replicated laboratory design. Goldfish were present in direct contact with newts in half of the tanks. Consistently throughout the study period, significantly more newts used shelter in the presence of fish than in their absence. Newts also significantly decreased their sexual activity level overall, but specially outside the shelter when they were in direct contact with fish. These results show that fish presence can affect newts in complex ways, such as through inhibition of their reproduction. Our work highlights that integrating behaviour in conservation studies is essential to understanding the patterns of coexistence and exclusion between introduced fish and amphibians. PMID:24312432

FEM simulation of a sono-reactor accounting for vibrations of the boundaries.

PubMed

Louisnard, O; Gonzalez-Garcia, J; Tudela, I; Klima, J; Saez, V; Vargas-Hernandez, Y

2009-02-01

The chemical effects of acoustic cavitation are obtained in sono-reactors built-up from a vessel and an ultrasonic source. In this paper, simulations of an existing sono-reactor are carried out, using a linear acoustics model, accounting for the vibrations of the solid walls. The available frequency range of the generator (19-21 kHz) is systematically scanned. Global quantities are plotted as a function of frequency in order to obtain response curves, exhibiting several resonance peaks. In absence of the precise knowledge of the bubbles size distribution and spatial location, the attenuation coefficient of the wave is taken as a variable, but spatially uniform parameter, and its influence is studied. The concepts of acoustic energy, intensity, active power, and source impedance are recalled, along with the general balance equation for acoustic energy, which is used as a convergence check of the simulations. It is shown that the interface between the liquid and the solid walls cannot be correctly represented by the simple approximations of either infinitely soft, or infinitely hard boundaries. Moreover, the liquid-solid coupling allows the cooling jacket to receive a noticeable part of the input power, although it is not in direct contact with the sonotrode. It may therefore undergo cavitation and this feature opens the perspective to design sono-reactors which avoid direct contact between the working liquid and the sonotrode. Besides, the possibility to shift the main pressure antinode far from the sonotrode area by exciting a resonance of the system is examined.

A microscopy approach for in situ inspection of micro-coordinate measurement machine styli for contamination

NASA Astrophysics Data System (ADS)

Feng, Xiaobing; Pascal, Jonathan; Lawes, Simon

2017-09-01

During the process of measurement using a micro-coordinate measurement machine (µCMM) contamination gradually builds up on the surface of the stylus tip and affects the dimensional accuracy of the measurement. Regular inspection of the stylus for contamination is essential to determine the appropriate cleaning interval and prevent the dimensional error from becoming significant. However, in situ inspection of a µCMM stylus is challenging due to the size, spherical shape, material and surface properties of a typical stylus. To address this challenge, this study evaluates several non-contact measurement technologies for in situ stylus inspection and, based on those findings, proposes a cost-effective microscopy approach. The operational principle is then demonstrated by an automated prototype, coordinated directly by the CMM software MCOSMOS, with an effective threshold of detection as low as 400 nm and a large field of view and depth of field. The level of contamination on the stylus has been found to increase steadily with the number of measurement contacts made. Once excessive contamination is detected on the stylus, measurement should be stopped and a stylus cleaning procedure should be performed to avoid affecting measurement accuracy.

Vector prevalence and detection of Crimean-Congo haemorrhagic fever virus in Golestan Province, Iran.

PubMed

Sedaghat, Mohammad Mehdi; Sarani, Moslem; Chinikar, Sadegh; Telmadarraiy, Zakiye; Moghaddam, Abdolreza Salahi; Azam, Kamal; Nowotny, Norbert; Fooks, Anthony R; Shahhosseini, Nariman

2017-01-01

Crimean-Congo haemorrhagic fever virus (CCHFV) causes severe disease with fatality rate of 30%. The virus is transmitted to humans through the bite of an infected tick, direct contact with the products of infected livestock as well as nosocomially. The disease occurs sporadically throughout many of African, Asian and European countries. Different species of ticks serve either as vector or reservoir for CCHFV. This study was aimed to determine the prevalence of CCHFV in hard ticks (Ixodidae) in the Golestan Province of Iran. A molecular survey was conducted on hard ticks (Ixodidae) isolated from six counties in Golestan Province, north of Iran during 2014-15. The ticks were identified using morphological characteristics and presence of CCHFV RNA was detected using RT-PCR. Data revealed the presence of CCHFV in 5.3% of the ticks selected for screening. The infected ticks belonged to Hyalomma dromedarii, Hy. anatolicum, Hy. marginatum and Rhipicephalus sanguineus species. The study demonstrated that Hyalomma ticks are the main vectors of CCHFV in Golestan Province. Thus, preventive strategies such as using acaricides and repellents in order to avoid contact with Hyalomma ticks are proposed.

Sensitization to serum albumins in children allergic to cow's milk and epithelia.

PubMed

Vicente-Serrano, J; Caballero, M L; Rodríguez-Pérez, R; Carretero, P; Pérez, R; Blanco, J G; Juste, S; Moneo, I

2007-09-01

Patients with persistent milk allergy and specific immunoglobulin E (IgE) to bovine serum albumin (BSA) have a greater risk of rhinoconjunctivitis and asthma because of animal dander. To prove the cross-reactivity between serum albumin (SA) of different mammals in milk, meat, and epithelia and determine if heat treatment of meats decrease the allergenicity of albumins. The study was performed using SDS-PAGE and IgE-immunoblotting using sera from eight patients sensitized to milk, BSA, and animal danders. Sera from non-allergic and only animal dander allergic subjects served as a control. With one exception, all patients' sera recognized SA in different meats (beef, lamb, deer, and pork), epithelia (dog, cat, and cow), and cow's milk. Some patients even were only sensitized to SA in meat and epithelia. Danders' allergic only recognized other proteins in epithelia but not SA. No patients reacted to SA from heated meat extracts. Serum albumin is an important allergen involved in milk, meat, and epithelia allergy. The first contact with SA was through cow's milk and patients developed sensitization to epithelia SA even without direct contact with animals. Patients with both BSA and cow's milk allergy must avoid raw meats and furry pets.

Directed evolution of human T cell receptor CDR2 residues by phage display dramatically enhances affinity for cognate peptide-MHC without increasing apparent cross-reactivity

PubMed Central

Dunn, Steven M.; Rizkallah, Pierre J.; Baston, Emma; Mahon, Tara; Cameron, Brian; Moysey, Ruth; Gao, Feng; Sami, Malkit; Boulter, Jonathan; Li, Yi; Jakobsen, Bent K.

2006-01-01

The mammalian α/β T cell receptor (TCR) repertoire plays a pivotal role in adaptive immunity by recognizing short, processed, peptide antigens bound in the context of a highly diverse family of cell-surface major histocompatibility complexes (pMHCs). Despite the extensive TCR–MHC interaction surface, peptide-independent cross-reactivity of native TCRs is generally avoided through cell-mediated selection of molecules with low inherent affinity for MHC. Here we show that, contrary to expectations, the germ line-encoded complementarity determining regions (CDRs) of human TCRs, namely the CDR2s, which appear to contact only the MHC surface and not the bound peptide, can be engineered to yield soluble low nanomolar affinity ligands that retain a surprisingly high degree of specificity for the cognate pMHC target. Structural investigation of one such CDR2 mutant implicates shape complementarity of the mutant CDR2 contact interfaces as being a key determinant of the increased affinity. Our results suggest that manipulation of germ line CDR2 loops may provide a useful route to the production of high-affinity TCRs with therapeutic and diagnostic potential. PMID:16600963

Determination of diffusion and partition coefficients of model migrants by direct contact and vapour phase transfer from low-density polyethylene films into cake.

PubMed

Paseiro-Cerrato, Rafael; Rodríguez-Bernaldo de Quirós, Ana; Otero-Pazos, Pablo; Sendón, Raquel; Paseiro-Losada, Perfecto

2018-03-01

The aim of the present study was to determine the migration kinetics of one photoinitiator, benzophenone, and two optical brighteners, Uvitex OB and 1,4-diphenyl-1,3-butadiene (DPBD), from low-density polyethylene (LDPE) films into cake. Transfer was assessed by both direct contact and also the vapour phase. To perform the migration tests by direct contact, plastic films enriched with the additives were placed between two cake slices. To evaluate the migration through the gas phase, cake and the fortified LDPE film were placed with no direct contact in a glass container that was hermetically closed. Samples were stored at different time-temperature conditions. Target compounds were extracted from the films with ethanol (70°C, 24 h) and analysed by HPLC-DAD. Relevant parameters such as partition and diffusion coefficients between food and plastic film were calculated. The Arrhenius equation was applied to estimate the diffusion coefficient at any temperature. The data indicate that migration of benzophenone occurs in a significant extent into cake by both direct contact and through the gas phase (no direct contact). Conversely, very little migration occurred for Uvitex OB by direct contact and none through the gas phase. Results for benzophenone suggest that migration through the gas phase should be considered when evaluating migration from food packaging materials into food.

Healthcare Industry Injuries by Patient Contact Status in Kentucky, 2012-2014.

PubMed

Ranzenberger, Kristen; Bunn, Terry L; Slavova, Svetla

2016-10-01

The healthcare industry continues to have a high number of reported injuries. The purpose of this study was to characterize healthcare industry injuries by patient contact status, identify the occupations associated with healthcare injuries by patient contact status, and determine healthcare injury rates by occupation to gain a better understanding of healthcare industry-compensated injuries and better target safety practices and programs in the healthcare industry. Kentucky healthcare industry workers' compensation first reports of injuries from calendar years 2012-2014 were categorized into injuries involved in direct patient contact versus injuries without direct patient contact using narrative text analysis. Injury numbers and rates were calculated for a number of data variables. Healthcare injuries without direct patient contact (55% of all first reports of injuries) occurred more frequently among older workers (45 years old and older [51%]), in "other" occupations such as housekeeping and maintenance (28%), and as a result of falls/slips/trips (39%) and sprains/tears (38%). In contrast, a higher percentage of healthcare injuries involving direct patient contact occurred among workers younger than 35 years (48%), in healthcare support occupations (50%), and resulting from sprains/tears (66%) and lifting/handling (52%), compared with those without direct patient contact. Findings from this study can better target the need for new and/or additional specific workplace safety training, especially in the healthcare support and nursing occupations with and without patient contact.

Patterns of direct and indirect contact between cattle and badgers naturally infected with tuberculosis.

PubMed

Drewe, J A; O'Connor, H M; Weber, N; McDonald, R A; Delahay, R J

2013-07-01

Tuberculosis (TB) due to infection with Mycobacterium bovis is transmitted between cattle and badgers (Meles meles) in the UK and Ireland but it is unclear where or when transmission occurs. We investigated direct and indirect interactions between badgers and cattle using automated proximity loggers on animals and at badger latrines located on pasture, in an area of south-west England with a high-density badger population. Direct contacts (interactions within 1.4 m) between badgers and cattle at pasture were very rare (four out of >500000 recorded animal-to-animal contacts) despite ample opportunity for interactions to occur. Indirect interactions (visits to badger latrines by badgers and cattle) were two orders of magnitude more frequent than direct contacts: 400 visits by badgers and 1700 visits by cattle were recorded. This suggests that indirect contacts might be more important than direct contacts in terms of disease transmission at pasture. The TB infection status of individual badgers (ascribed with 93% accuracy using three diagnostic tests) did not affect the frequency or duration of their visits to latrines located on pasture grazed by cattle. Nevertheless, there was wide variation in contact behaviour between individuals, which highlights the importance of understanding heterogeneity in contact patterns when developing strategies to control disease spread in wildlife and livestock.

The equivalence of numbers: The social value of avoiding health decline: An experimental web-based study

PubMed Central

Schwappach, David LB

2002-01-01

Background Health economic analysis aimed at informing policy makers and supporting resource allocation decisions has to evaluate not only improvements in health but also avoided decline. Little is known however, whether the "direction" in which changes in health are experienced is important for the public in prioritizing among patients. This experimental study investigates the social value people place on avoiding (further) health decline when directly compared to curative treatments in resource allocation decisions. Methods 127 individuals completed an interactive survey that was published in the World Wide Web. They were confronted with a standard gamble (SG) and three person trade-off tasks, either comparing improvements in health (PTO-Up), avoided decline (PTO-Down), or both, contrasting health changes of equal magnitude differing in the direction in which they are experienced (PTO-WAD). Finally, a direct priority ranking of various interventions was obtained. Results Participants strongly prioritized improving patients' health rather than avoiding decline. The mean substitution rate between health improvements and avoided decline (WAD) ranged between 0.47 and 0.64 dependent on the intervention. Weighting PTO values according to the direction in which changes in health are experienced improved their accuracy in predicting a direct prioritization ranking. Health state utilities obtained by the standard gamble method seem not to reflect social values in resource allocation contexts. Conclusion Results suggest that the utility of being cured of a given health state might not be a good approximation for the societal value of avoiding this health state, especially in cases of competition between preventive and curative interventions. PMID:11879529

SARS Patients and Their Close Contacts

MedlinePlus

... symptoms, limit your activities outside the home. Avoid public transportation (e.g., bus, taxi). Do not go to ... wear a mask, if tolerated. Do not use public transportation. Wash your hands often and well, especially after ...

75 FR 56105 - Pesticide Products; Registration Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-15

... website is an ``anonymous access'' system, which means EPA will not know your identity or contact... files should avoid the use of special characters, any form of encryption, and be free of any defects or...

75 FR 3235 - Pesticide Products; Registration Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-20

... website is an ``anonymous access'' system, which means EPA will not know your identity or contact... files should avoid the use of special characters, any form of encryption, and be free of any defects or...

75 FR 4383 - Pesticide Products: Registration Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-27

... website is an ``anonymous access'' system, which means EPA will not know your identity or contact... files should avoid the use of special characters, any form of encryption, and be free of any defects or...

Behavioral consequences of predator stress in the rat elevated T-maze.

PubMed

Bulos, Erika Mondin; Pobbe, Roger Luis Henschel; Zangrossi, Helio

2015-07-01

Analyses of the behavioral reactions of rodents to predators have greatly contributed to the understanding of defense-related human psychopathologies such as anxiety and panic.We here investigated the behavioral consequences of exposing male Wistar rats to a live cat using the elevated T-maze test of anxiety. This test allows the measurement of two defensive responses: inhibitory avoidance and escape, which in terms of pathology have been associated with generalized anxiety and panic disorders, respectively. For comparative reasons, the effects of exposure to the cat were also assessed in the elevated plus-maze. The results showed that a 5-min exposure to the cat selectively facilitated inhibitory avoidance acquisition, an anxiogenic effect, without affecting escape expression in the elevated T-maze. This was seen immediately but not 30 min after contact with the predator. This short-lived anxiogenic effect was also detected in the elevated plus-maze. Previous administration of the benzodiazepine anxiolytic diazepam (2 mg/kg) decreased the immediate avoidance response to the predator and the neophobic reaction to a dummy cat used as a control stimulus. The drug also impaired inhibitory avoidance acquisition in the elevated T-maze, indicating an anxiolytic effect, without affecting escape performance. The results indicate that the state of anxiety evoked during contact with the predator generalizes to both elevated plus- and T-mazes, impacting on defensive responses associated with generalized anxiety disorder.

Experimental analysis of the Schottky barrier height of metal contacts in black phosphorus field-effect transistors

NASA Astrophysics Data System (ADS)

Chang, Hsun-Ming; Fan, Kai-Lin; Charnas, Adam; Ye, Peide D.; Lin, Yu-Ming; Wu, Chih-I.; Wu, Chao-Hsin

2018-04-01

Compared to graphene and MoS2, studies on metal contacts to black phosphorus (BP) transistors are still immature. In this work, we present the experimental analysis of titanium contacts on BP based upon the theory of thermionic emssion. The Schottky barrier height (SBH) is extracted by thermionic emission methods to analyze the properties of Ti-BP contact. To examine the results, the band gap of BP is extracted followed by theoretical band alignment by Schottky-Mott rule. However, an underestimated SBH is found due to the hysteresis in electrical results. Hence, a modified SBH extraction for contact resistance that avoids the effects of hysteresis is proposed and demonstrated, showing a more accurate SBH that agrees well with theoretical value and results of transmission electron microscopy and energy-dispersive x-ray spectroscopy.

Air/molten salt direct-contact heat-transfer experiment and economic analysis

NASA Astrophysics Data System (ADS)

Bohn, M. S.

1983-11-01

Direct-contact heat-transfer coefficients have been measured in a pilot-scale packed column heat exchanger for molten salt/air duty. Two types of commercial tower packings were tested: metal Raschig rings and initial Pall rings. Volumetric heat-transfer coefficients were measured and appeared to depend upon air flow but not on salt flow rate. An economic analysis was used to compare the cost-effectiveness of direct-contact heat exchange with finned-tube heat exchanger in this application. Incorporating the measured volumetric heat-transfer coefficients, a direct-contact system appeared to be from two to five times as cost-effective as a finned-tube heat exchanger, depending upon operating temperature. The large cost advantage occurs for higher operating temperatures (2700(0)C), where high rates of heat transfer and flexibility in materials choice give the cost advantage to the direct-contact heat exchanger.

In the eye of the beholder: eye contact increases resistance to persuasion.

PubMed

Chen, Frances S; Minson, Julia A; Schöne, Maren; Heinrichs, Markus

2013-11-01

Popular belief holds that eye contact increases the success of persuasive communication, and prior research suggests that speakers who direct their gaze more toward their listeners are perceived as more persuasive. In contrast, we demonstrate that more eye contact between the listener and speaker during persuasive communication predicts less attitude change in the direction advocated. In Study 1, participants freely watched videos of speakers expressing various views on controversial sociopolitical issues. Greater direct gaze at the speaker's eyes was associated with less attitude change in the direction advocated by the speaker. In Study 2, we instructed participants to look at either the eyes or the mouths of speakers presenting arguments counter to participants' own attitudes. Intentionally maintaining direct eye contact led to less persuasion than did gazing at the mouth. These findings suggest that efforts at increasing eye contact may be counterproductive across a variety of persuasion contexts.

Laser measurement of respiration activity in preterm infants: Monitoring of peculiar events

NASA Astrophysics Data System (ADS)

Scalise, L.; Marchionni, P.; Ercoli, I.; Tomasini, E. P.

2012-09-01

The Neonatal Intensive Care Unit (NICU) is a part of a pediatric hospital dedicated to the care of ill or pre-term patients . NICU's patients are underweight and most of the time they need cardiac and respiratory support therapies; they are placed in incubators or in cribs maintaining target environmental and body temperatures and protecting patients from bacteria and virus. Patients are continuously monitored for long period of time (days or weeks) due to their possible several health conditions. the most common vital signs monitored are: respiration rate, heart rate, body temperature, blood saturation, etc. Most of the devices used for transducing such quantities in electronic signals - like spirometer or electrocardiogram (ECG) - are in direct contact with the patient and results, also in consideration of the specific patient, largely invasive. In this paper, we propose a novel measurement system for non-contact and non-invasive assessment of the respiration activity, with particular reference to the detection of peculiar respiration events of extreme interest in intensive care units, such as: irregular inspiration/expiration acts, hiccups and apneas. The sensing device proposed is the Laser Doppler Vibrometer (LDVi) which is an non contact, optical measurement system for the assessment of a surface velocity and displacement. In the past it has been demonstrated to be suitable to measure heart rate (HR) and respiration rate (RR) in adult and in preterm infant trough chest-wall displacements. The measurement system is composed by a LDVi system and a data acquisition board installed on a PC, with no direct contact with the patient. Tests have been conducted on 20 NICU patients, for a total of 7219 data sampled. Results show very high correlation (R=0.99) with the reference instrument used for the patient monitoring (mechanical ventilator), with an uncertainty < ±7 ms (k=2). Moreover, during the tests, some peculiar respiration events, have been recorded on 6 of the monitored patients: irregular inspiration/expiration acts (4), hiccups (1) and apneas (1). The proposed measurement method shows to be able to precisely detect the instantaneous respiration frequency of the patient, avoiding patient contact. Moreover the signal collected allow to identify irregularities in the patient respiration of different severity, allowing an optimized action of the care givers.

Contact sponge water absorption test implemented for in situ measures

NASA Astrophysics Data System (ADS)

Gaggero, Laura; Scrivano, Simona

2016-04-01

The contact sponge method is a non-destructive in-situ methodology used to estimate a water uptake coefficient. The procedure, unlike other in-situ measurement was proven to be directly comparable to the water uptake laboratory measurements, and was registered as UNI 11432:2011. The UNI Normal procedure requires to use a sponge with known density, soaked in water, weighed, placed on the material for 1 minute (UNI 11432, 2011; Pardini & Tiano, 2004), then weighed again. Difficulties arise in operating on test samples or on materials with porosity varied for decay. While carrying on the test, fluctuations in the bearing of the environmental parameters were negligible, but not the pressure applied to the surface, that induced the release of different water amounts towards the material. For this reason we designed a metal piece of the same diameter of the plate carrying the sponge, to be screwed at the tip of a pocket penetrometer. With this instrument the sponge was kept in contact with the surface for 1 minute applying two different loads, at first pushed with 0.3 kg/cm2 in order to press the sponge, but not its holder, against the surface. Then, a load of 1.1 kg/ cm2 was applied, still avoiding deviating the load to the sponge holder. We applied both the current and our implemented method to determine the water absorption by contact sponge on 5 fresh rock types (4 limestones: Fine - and Coarse grained Pietra di Vicenza, Rosso Verona, Breccia Aurora, and the silicoclastic Macigno sandstone). The results show that 1) the current methodology imply manual skill and experience to produce a coherent set of data; the variable involved are in fact not only the imposed pressure but also the compression mechanics. 2) The control on the applied pressure allowed reproducible measurements. Moreover, 3) the use of a thicker sponge enabled to apply the method even on rougher surfaces, as the device holding the sponge is not in contact with the tested object. Finally, 4) the implemented measurements gave the possibility of a direct comparison with the capillary water absorption method. Pardini C. & Tiano P. 2004. Valutazione in situ dei trattamenti protettivi per il materiale lapideo, proposta di una nuova semplice metodologia. ARKOS, 5, 30-36. UNI 11432. 2011. Beni culturali Materiali lapidei naturali ed artificiali - Misura della capacita di assorbimento di acqua mediante spugna di contatto. P. 6.

IgE-mediated food allergy in children.

PubMed

Longo, Giorgio; Berti, Irene; Burks, A Wesley; Krauss, Baruch; Barbi, Egidio

2013-11-16

Food allergy is a serious health issue affecting roughly 4% of children, with a substantial effect on quality of life. Prognosis is good for the most frequent allergens with almost all children outgrowing their allergy. However, the long-term implications for disease burden are substantial for children with persistent allergies (eg, peanuts, tree nuts, fish, and shellfish) and for those with high concentrations of milk, egg, and wheat IgE. Antigen avoidance has been the time-honoured approach both for prevention and treatment. However, findings from studies done in the past 5 years show that early contact with food can induce tolerance and desensitisation to foods. We review the epidemiology, natural history, and management of food allergy, and discuss the areas of controversy and future directions in research and clinical practice. Copyright © 2013 Elsevier Ltd. All rights reserved.

Rules of Engagement: The Type VI Secretion System in Vibrio cholerae.

PubMed

Joshi, Avatar; Kostiuk, Benjamin; Rogers, Andrew; Teschler, Jennifer; Pukatzki, Stefan; Yildiz, Fitnat H

2017-04-01

Microbial species often exist in complex communities where they must avoid predation and compete for favorable niches. The type VI secretion system (T6SS) is a contact-dependent bacterial weapon that allows for direct killing of competitors through the translocation of proteinaceous toxins. Vibrio cholerae is a Gram-negative pathogen that can use its T6SS during antagonistic interactions with neighboring prokaryotic and eukaryotic competitors. The T6SS not only promotes V. cholerae's survival during its aquatic and host life cycles, but also influences its evolution by facilitating horizontal gene transfer. This review details the recent insights regarding the structure and function of the T6SS as well as the diverse signals and regulatory pathways that control its activation in V. cholerae. Copyright © 2016 Elsevier Ltd. All rights reserved.

Dendritic cells: key to fetal tolerance?

PubMed

Blois, Sandra M; Kammerer, Ulrike; Alba Soto, Catalina; Tometten, Mareike C; Shaikly, Valerie; Barrientos, Gabriela; Jurd, Richard; Rukavina, Daniel; Thomson, Angus W; Klapp, Burghard F; Fernández, Nelson; Arck, Petra C

2007-10-01

Pregnancy is a unique event in which a fetus, despite being genetically and immunologically different from the mother (a hemi-allograft), develops in the uterus. Successful pregnancy implies avoidance of rejection by the maternal immune system. Fetal and maternal immune cells come into direct contact at the decidua, which is a highly specialized mucous membrane that plays a key role in fetal tolerance. Uterine dendritic cells (DC) within the decidua have been implicated in pregnancy maintenance. DC serve as antigen-presenting cells with the unique ability to induce primary immune responses. Just as lymphocytes comprise different subsets, DC subsets have been identified that differentially control lymphocyte function. DC may also act to induce immunologic tolerance and regulation of T cell-mediated immunity. Current understanding of DC immunobiology within the context of mammalian fetal-maternal tolerance is reviewed and discussed herein.

Bradbury

Science.gov Websites

Search Site submit About | Contacts | Directions Los Alamos National LaboratoryBradbury Science Museum Your Window into Los Alamos National Laboratory Bradbury Science Museum Menu About Contacts Directions Visit Visitor Information About the Museum Large Group Visits Around Los Alamos Contact Us

Staph infections - self-care at home

MedlinePlus

... soap and water. Or use an alcohol-based hand sanitizer. Keep cuts and scrapes clean and covered with bandages until they heal. Avoid contact with other people's wounds ... your hands well before and after playing sports. Shower right ...

75 FR 24690 - Agency Information Collection Activities; Proposed Collection; Comment Request; Plant...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-05

... website is an ``anonymous access'' system, which means EPA will not know your identity or contact... your comment. Electronic files should avoid the use of special characters, any form of encryption, and...

Tooth Decay Process: How to Reverse It and Avoid a Cavity

MedlinePlus

... Fellowships, & Training Grants Job Openings Diversity Loan Repayment Staff Contacts News & Events - + NIDCR News E-Newsletters Grantee ... For Reporters About Us - + Mission Strategic Plan Leadership & Staff Advisory Committees Budget & Congressional Job Openings Diversity Getting ...

Design of an Active Bumper with a Series Elastic Actuator for Pedestrian Protection of Small Unmanned Vehicles

NASA Astrophysics Data System (ADS)

Terumasa, Narukawa; Tomoki, Tsuge; Hiroshi, Yamamoto; Takahiro, Suzuki

2016-09-01

When autonomous unmanned vehicles are operated on sidewalks, the vehicles must have high safety standards such as avoiding injury when they come in contact with pedestrians. In this study, we established a design for preventing serious injury when such collisions occur. We designed an active bumper with a series elastic actuator, with the goal of avoiding serious injury to a pedestrian in a collision with a small unmanned vehicle. The series elastic actuator comprised an elastic element in series with a table driven by a ball screw and servo motor. The active bumper was used to control the contact force between a vehicle and a pedestrian. The optimal force for minimizing the deflection of the object of the collision was derived, and the actuator controlled to apply this optimal force. Numerical simulations showed that the active bumper was successful in improving the collision safety of small unmanned vehicles.

Xyloglucan, hibiscus and propolis for the prevention of urinary tract infections: results of in vitro studies.

PubMed

Fraile, Benito; Alcover, Javier; Royuela, Mar; Rodríguez, David; Chaves, Concepción; Palacios, Ricardo; Piqué, Núria

2017-06-01

To assess the properties of a medical device containing xyloglucan, propolis and hibiscus to create a bioprotective barrier to avoid the contact of uropathogenic Escherichia coli strains on cell walls in models of intestinal (CacoGoblet) and uroepithelial (RWPE-1) cells (derived from normal human prostate epithelium). Two uropathogenic E. coli strains (expressing type 1 fimbriae and P fimbriae) were used to assess, by electronic microscopy and ELISA, the barrier properties of the medical device. The antimicrobial activity was assessed in broth dilution assays. The three components (xyloglucan, propolis and hibiscus) did not alter E. coli cell integrity in intestinal and uroepithelial cell models and were devoid of antibacterial activity. The three components avoided bacterial contact in both cell monolayers. The nonpharmacological barrier properties of xyloglucan, propolis and hibiscus confirm the role of the medical device for the management of urinary tract infections.

Super-Hydrophobic Green Corrosion Inhibitor On Carbon Steel

NASA Astrophysics Data System (ADS)

Hassan, H.; Ismail, A.; Ahmad, S.; Soon, C. F.

2017-06-01

There are many examples of organic coatings used for corrosion protection. In particular, hydrophobic and super-hydrophobic coatings are shown to give good protection because of their enhanced ability to slow down transport of water and ions through the coating. The purpose of this research is to develop water repellent coating to avoid direct contact between metal and environment corrosive and mitigate corrosion attack at pipeline system. This water repellent characteristic on super-hydrophobic coating was coated by electrodeposition method. Wettability of carbon steel with super-hydrophobic coating (cerium chloride and myristic acid) and oxidized surface was investigated through contact angle and inhibitor performance test. The inhibitor performance was studied in 25% tannin acid corrosion test at 30°C and 3.5% sodium chloride (NaCl). The water contact angle test was determined by placing a 4-μL water droplet of distilled water. It shows that the wettability of contact angle super-hydrophobic with an angle of 151.60° at zero minute can be classified as super-hydrophobic characteristic. By added tannin acid as inhibitor the corrosion protection on carbon steel becomes more consistent. This reveals that the ability of the coating to withstand with the corrosion attack in the seawater at different period of immersions. The results elucidate that the weight loss increased as the time of exposure increased. However, the corrosion rates for uncoated carbon steel is high compared to coated carbon steel. As a conclusion, from both samples it can be seen that the coated carbon steel has less corrosion rated compared to uncoated carbon steel and addition of inhibitor to the seawater provides more protection to resist corrosion attack on carbon steel.

Understanding approach and avoidance in verbal descriptions of everyday actions: An ERP study.

PubMed

Marrero, Hipólito; Urrutia, Mabel; Beltrán, David; Gámez, Elena; Díaz, José M

2017-06-01

Understanding verbal descriptions of everyday actions could involve the neural representation of action direction (avoidance and approach) toward persons and things. We recorded the electrophysiological activity of participants while they were reading approach/avoidance action sentences that were directed toward a target: a thing/a person (i.e., "Petra accepted/rejected Ramón in her group"/ "Petra accepted/rejected the receipt of the bank"). We measured brain potentials time locked to the target word. In the case of things, we found a N400-like component with right frontal distribution modulated by approach/avoidance action. This component was more negative in avoidance than in approach sentences. In the case of persons, a later negative event-related potential (545-750 ms) with left frontal distribution was sensitive to verb direction, showing more negative amplitude for approach than avoidance actions. In addition, more negativity in approach-person sentences was associated with fear avoidance trait, whereas less negativity in avoidance-person sentences was associated with a greater approach trait. Our results support that verbal descriptions of approach/avoidance actions are encoded differently depending on whether the target is a thing or a person. Implications of these results for a social, emotional and motivational understanding of action language are discussed.

Use of group quarantine in Ebola control - Nigeria, 2014.

PubMed

Grigg, Cheri; Waziri, Ndadilnasiya E; Olayinka, Adebola T; Vertefeuille, John F

2015-02-13

On July 20, 2014, the first known case of Ebola virus disease (Ebola) in Nigeria, in a traveler from Liberia, led to an outbreak that was successfully curtailed with infection control, contact tracing, isolation, and quarantine measures coordinated through an incident management system. During this outbreak, most contacts underwent home monitoring, which included instructions to stay home or to avoid crowded areas if staying home was not possible. However, for five contacts with high-risk exposures, group quarantine in an observation unit was preferred because the five had crowded home environments or occupations that could have resulted in a large number of community exposures if they developed Ebola.

Management of contact dermatitis due to nickel allergy: an update

PubMed Central

Torres, Fernanda; das Graças, Maria; Melo, Mota; Tosti, Antonella

2009-01-01

Nickel is the major cause of allergic contact dermatitis in the general population, both among children and adults, as well as in large occupational groups. This metal is used in numerous industrial and consumer products, including stainless steel, magnets, metal plating, coinage, and special alloys, and is therefore almost impossible to completely avoid in daily life. Nickel contact dermatitis can represent an important morbidity, particularly in patients with chronic hand eczema, which can lead to inability to work, a decrease in quality of life and significant healthcare expenses. Therefore, its management is of great importance. This article reviews diagnostic, preventive and therapeutic strategies in this field. PMID:21436967

Method and apparatus for high-efficiency direct contact condensation

DOEpatents

Bharathan, D.; Parent, Y.; Hassani, A.V.

1999-07-20

A direct contact condenser having a downward vapor flow chamber and an upward vapor flow chamber, wherein each of the vapor flow chambers includes a plurality of cooling liquid supplying pipes and a vapor-liquid contact medium disposed thereunder to facilitate contact and direct heat exchange between the vapor and cooling liquid. The contact medium includes a plurality of sheets arranged to form vertical interleaved channels or passageways for the vapor and cooling liquid streams. The upward vapor flow chamber also includes a second set of cooling liquid supplying pipes disposed beneath the vapor-liquid contact medium which operate intermittently in response to a pressure differential within the upward vapor flow chamber. The condenser further includes separate wells for collecting condensate and cooling liquid from each of the vapor flow chambers. In alternate embodiments, the condenser includes a cross-current flow chamber and an upward flow chamber, a plurality of upward flow chambers, or a single upward flow chamber. The method of use of the direct contact condenser of this invention includes passing a vapor stream sequentially through the downward and upward vapor flow chambers, where the vapor is condensed as a result of heat exchange with the cooling liquid in the contact medium. The concentration of noncondensable gases in the resulting condensate-liquid mixtures can be minimized by controlling the partial pressure of the vapor, which depends in part upon the geometry of the vapor-liquid contact medium. In another aspect of this invention, the physical and chemical performance of a direct contact condenser can be predicted based on the vapor and coolant compositions, the condensation conditions, and the geometric properties of the contact medium. 39 figs.

Method and apparatus for high-efficiency direct contact condensation

DOEpatents

Bharathan, Desikan; Parent, Yves; Hassani, A. Vahab

1999-01-01

A direct contact condenser having a downward vapor flow chamber and an upward vapor flow chamber, wherein each of the vapor flow chambers includes a plurality of cooling liquid supplying pipes and a vapor-liquid contact medium disposed thereunder to facilitate contact and direct heat exchange between the vapor and cooling liquid. The contact medium includes a plurality of sheets arranged to form vertical interleaved channels or passageways for the vapor and cooling liquid streams. The upward vapor flow chamber also includes a second set of cooling liquid supplying pipes disposed beneath the vapor-liquid contact medium which operate intermittently in response to a pressure differential within the upward vapor flow chamber. The condenser further includes separate wells for collecting condensate and cooling liquid from each of the vapor flow chambers. In alternate embodiments, the condenser includes a cross-current flow chamber and an upward flow chamber, a plurality of upward flow chambers, or a single upward flow chamber. The method of use of the direct contact condenser of this invention includes passing a vapor stream sequentially through the downward and upward vapor flow chambers, where the vapor is condensed as a result of heat exchange with the cooling liquid in the contact medium. The concentration of noncondensable gases in the resulting condensate-liquid mixtures can be minimized by controlling the partial pressure of the vapor, which depends in part upon the geometry of the vapor-liquid contact medium. In another aspect of this invention, the physical and chemical performance of a direct contact condenser can be predicted based on the vapor and coolant compositions, the condensation conditions. and the geometric properties of the contact medium.

How do adults and teens with self-declared Autism Spectrum Disorder experience eye contact? A qualitative analysis of first-hand accounts

PubMed Central

Roberts, Nicole; Lin, Cathy; Birmingham, Elina

2017-01-01

A tendency to avoid eye contact is an early indicator of Autism Spectrum Disorder (ASD), and difficulties with eye contact often persist throughout the lifespan. Eye contact difficulties may underlie social cognitive deficits in ASD, and can create significant social and occupational barriers. Thus, this topic has received substantial research and clinical attention. In this study, we used qualitative methods to analyze self-reported experiences with eye contact as described by teens and adults with self-declared ASD. Results suggest people with a self- declared ASD diagnosis experience adverse emotional and physiological reactions, feelings of being invaded, and sensory overload while making eye contact, in addition to difficulties understanding social nuances, and difficulties receiving and sending nonverbal information. Some data support existing mindblindness frameworks, and hyperarousal or hypoarousal theories of eye contact, but we also present novel findings unaccounted for by existing frameworks. Additionally, we highlight innovative strategies people with self-declared ASD have devised to overcome or cope with their eye contact difficulties. PMID:29182643

A bio-inspired kinematic controller for obstacle avoidance during reaching tasks with real robots.

PubMed

Srinivasa, Narayan; Bhattacharyya, Rajan; Sundareswara, Rashmi; Lee, Craig; Grossberg, Stephen

2012-11-01

This paper describes a redundant robot arm that is capable of learning to reach for targets in space in a self-organized fashion while avoiding obstacles. Self-generated movement commands that activate correlated visual, spatial and motor information are used to learn forward and inverse kinematic control models while moving in obstacle-free space using the Direction-to-Rotation Transform (DIRECT). Unlike prior DIRECT models, the learning process in this work was realized using an online Fuzzy ARTMAP learning algorithm. The DIRECT-based kinematic controller is fault tolerant and can handle a wide range of perturbations such as joint locking and the use of tools despite not having experienced them during learning. The DIRECT model was extended based on a novel reactive obstacle avoidance direction (DIRECT-ROAD) model to enable redundant robots to avoid obstacles in environments with simple obstacle configurations. However, certain configurations of obstacles in the environment prevented the robot from reaching the target with purely reactive obstacle avoidance. To address this complexity, a self-organized process of mental rehearsals of movements was modeled, inspired by human and animal experiments on reaching, to generate plans for movement execution using DIRECT-ROAD in complex environments. These mental rehearsals or plans are self-generated by using the Fuzzy ARTMAP algorithm to retrieve multiple solutions for reaching each target while accounting for all the obstacles in its environment. The key aspects of the proposed novel controller were illustrated first using simple examples. Experiments were then performed on real robot platforms to demonstrate successful obstacle avoidance during reaching tasks in real-world environments. Copyright © 2012 Elsevier Ltd. All rights reserved.

Pilot study on use of home telephoning to identify and recruit high-risk individuals for lung cancer screening.

PubMed

Veronesi, Giulia; Colombo, Paolo; Novellis, Pierluigi; Crepaldi, Alessandro; Lutman, Romano Fabio; Dieci, Elisa; Profili, Manuel; Siracusano, Licia; Alloisio, Marco

2017-03-01

Widespread lung cancer screening with low-dose computed tomography is urgently needed in Europe to identify lung cancers early and reduce lung cancer deaths. The most effective method of identifying high-risk individuals and recruiting them for screening has not been determined. In the present pilot study we investigated direct telephoning to families as a way of identifying high risk individuals and recruiting them to a screening/smoking cessation program, that avoided the selection bias of voluntary screening. Families in the province of Milan, Italy, were contacted by telephone at their homes and asked about family members over 50 years who were heavy smokers (30 or more pack-years). Persons meeting these criteria were contacted and asked to participate in the program. Those who agreed were given an appointment to undergo screening and receive smoking cessation counseling. Among the 1000 contacted families, involving 2300 persons, 44 (1.9%) were eligible for LDCT screening, and 12 (27%) of these participated in the program. The cost of this recruitment strategy pilot study was around 150 euro per screened subject. We obtained useful information on the proportion of the general population eligible for lung cancer screening and the proportion of those who responded. However the cost of home telephone calling is probably too high to be practicable as a method of recruiting high risk persons for screening. Alternative recruitment methods, possibly involving family physicians practitioners, need to be investigated. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

Bradbury Science Museum

Science.gov Websites

Search Site submit About | Contacts | Directions Los Alamos National LaboratoryBradbury Science Museum Your Window into Los Alamos National Laboratory Bradbury Science Museum Menu About Contacts Directions Visit Visitor Information About the Museum Large Group Visits Around Los Alamos Contact Us

Epidemics in adaptive networks with community structure

NASA Astrophysics Data System (ADS)

Shaw, Leah; Tunc, Ilker

2010-03-01

Models for epidemic spread on static social networks do not account for changes in individuals' social interactions. Recent studies of adaptive networks have modeled avoidance behavior, as non-infected individuals try to avoid contact with infectives. Such models have not generally included realistic social structure. Here we study epidemic spread on an adaptive network with community structure. We model the effect of heterogeneous communities on infection levels and epidemic extinction. We also show how an epidemic can alter the community structure.

Conflict resolution in an ant-plant interaction: Acacia constricta traits reduce ant costs to reproduction.

PubMed

Nicklen, E Fleur; Wagner, Diane

2006-05-01

Many plant species attract ants onto their foliage with food rewards or nesting space. However, ants can interfere with plant reproduction when they visit flowers. This study tests whether Acacia constricta separates visiting ant species temporally or spatially from newly opened inflorescences and pollinators. The diurnal activity patterns of ants and A. constricta pollinators peaked at different times of day, and the activity of pollinators followed the daily dehiscence of A. constricta inflorescences. In addition to being largely temporally separated, ants rarely visited open inflorescences. A floral ant repellent contributes to the spatial separation of ants and inflorescences. In a field experiment, ants of four species were given equal access to inflorescences in different developmental stages. On average, the frequency with which ants made initial, antennal contact with the floral stages did not differ, but ants significantly avoided secondary contact with newly opened inflorescences relative to buds and old inflorescences, and old inflorescences relative to buds. Ants also avoided contact with pollen alone, indicating that pollen is at least one source of the repellent. The results suggest A. constricta has effectively resolved the potential conflict between visiting ants and plant reproduction.

Gaps in Workplace Education For Prevention of Occupational Skin Disease.

PubMed

Gupta, Tanya; Arrandale, Victoria H; Kudla, Irena; Holness, D Linn

2018-02-13

Occupational contact dermatitis (OCD) is a common occupational disease. Evidence suggests that education and training are effective prevention strategies. In spite of these known prevention strategies, workers continue to develop OCD. Little is reported regarding the actual training experience of workers. To examine the training experience of workers with contact dermatitis to identify areas for improvement. Participants were workers being assessed for contact dermatitis in an occupational health clinic. The anonymous survey collected demographics, workplace characteristics, and education and prevention practices. Approximately 80% reported general occupational health and safety training; however, only 49% reported skin-specific training (SST). For workers reporting SST, most received information regarding exposure avoidance, hand washing, and glove use. This content was reported as helpful by at least 50%. Workers who did not receive SST indicated the most important content would be warning signs of skin problems, how to avoid exposure and skin care while using gloves. While the study was anonymous and used self-reported of training experience, the study suggests there are gaps in skin protection training. Addressing these gaps may lead to improved prevention and reduction in OCD. © The Author(s) 2017. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Approaches of health caregivers to young children in a pediatric intensive care unit.

PubMed

Orsuto, J; Corbo, B H

1987-01-01

This study explored the frequency of health caregiver approaches to 12 toddlers and preschool children in a pediatric intensive care unit. Using a time-sampling methodology, 3 hours of observation per child were obtained; half occurred between 7 A.M. and 7 P.M. and half were between 7 P.M. and 7 A.M.. Data were analyzed using descriptive statistics. Caregiver approaches involved either direct or indirect contact. Indirect contacts occurred three times more frequently than direct, with registered nurses initiating more contacts than any other caregivers. The greatest number of direct contacts were categorized as intrusive, while the least number were comforting contacts. The findings suggest that nurses are in optimal positions to promote rest and comforting contact for children in the pediatric intensive care unit.

Investigations into the thermal non-equilibrium of W UMa-type contact binaries

NASA Astrophysics Data System (ADS)

Xiong, Xiao; Liu, Liang; Qian, Sheng-Bang

2018-05-01

Traditionally, some physical details (e.g., magnetic braking, energy transfer, angular momentum loss, etc.) have to be taken into consideration during investigations into the evolution of contact binaries. However, the real evolutionary processes which usually contain several of these physical mechanisms are very complicated as a result of strong interaction between components. To avoid dealing with these factors, a linear relationship is applied to the temperatures of components. It is found that the higher the mass ratio (M 2/M 1) of a contact system, the weaker the deviation from thermal equilibrium. On this basis, a variation trend of fill-out factor (f) changing with mass ratio can be inferred, which is consistent with observations. Moreover, if we stick to this point of view, it should be natural that the number of semi-detached binaries in the predicted broken-contact phase of relaxation oscillations is less than the number in the contact phase.

Au/Zn Contacts to rho-InP: Electrical and Metallurgical Characteristics and the Relationship Between Them

NASA Technical Reports Server (NTRS)

Weizer, Victor G.; Fatemi, Navid S.; Korenyi-Both, Andras L.

1994-01-01

The metallurgical and electrical behavior of Au/Zn contacting metallization on p-type InP was investigated as a function of the Zn content in the metallization. It was found that ohmic behavior can be achieved with Zn concentrations as small as 0.05 atomic percent Zn. For Zn concentrations between 0.1 and 36 at. percent, the contact resistivity rho(sub c) was found to be independent of the Zn content. For low Zn concentrations the realization of ohmic behavior was found to require the growth of the compound Au2P3 at the metal-InP interface. The magnitude of rho(sub c) is shown to be very sensitive to the growth rate of the interfacial Au2P3 layer. The possibility of exploiting this sensitivity to provide low resistance contacts while avoiding the semiconductor structural damage that is normally attendant to contact formation is discussed.

From biofuels to predicting the flu

Science.gov Websites

Search Site submit About | Contacts | Directions Los Alamos National LaboratoryBradbury Science Museum Your Window into Los Alamos National Laboratory Bradbury Science Museum Menu About Contacts Directions Visit Visitor Information About the Museum Large Group Visits Around Los Alamos Contact Us

Climate change and the Arctic

Science.gov Websites

Search Site submit About | Contacts | Directions Los Alamos National LaboratoryBradbury Science Museum Your Window into Los Alamos National Laboratory Bradbury Science Museum Menu About Contacts Directions Visit Visitor Information About the Museum Large Group Visits Around Los Alamos Contact Us

Efficient Perovskite Solar Cells Depending on TiO2 Nanorod Arrays.

PubMed

Li, Xin; Dai, Si-Min; Zhu, Pei; Deng, Lin-Long; Xie, Su-Yuan; Cui, Qian; Chen, Hong; Wang, Ning; Lin, Hong

2016-08-24

Perovskite solar cells (PSCs) with TiO2 materials have attracted much attention due to their high photovoltaic performance. Aligned TiO2 nanorods have long been used for potential application in highly efficient perovskite solar cells, but the previously reported efficiencies of perovskite solar cells based on TiO2 nanorod arrays were underrated. Here we show a solvothermal method based on a modified ketone-HCl system with the addition of organic acids suitable for modulation of the TiO2 nanorod array films to fabricate highly efficient perovskite solar cells. Photovoltaic measurements indicated that efficient nanorod-structured perovskite solar cells can be achieved with the length of the nanorods as long as approximately 200 nm. A record efficiency of 18.22% under the reverse scan direction has been optimized by avoiding direct contact between the TiO2 nanorods and the hole transport materials, eliminating the organic residues on the nanorod surfaces using UV-ozone treatment and tuning the nanorod array morphologies through addition of different organic acids in the solvothermal process.

Heat transfer characteristics of a surface type direct contact boiler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deeds, R.S.; Jacobs, H.R.; Boehm, R.F.

1976-03-01

Two direct contact heat exchangers were constructed and test results were obtained using water and refrigerant 113 as the working fluids. The heat exchangers were operated in a three-phase mode; the water remained liquid throughout the vessel and the liquid refrigerant 113 underwent vaporization following direct injection into the water. The effect of important operational parameters--operating heights, refrigerant 113 injection techniques, mass flow ratios, and temperatures--was studied to determine generalized trends important in the design and operation of a prototype three-phase direct contact heat exchanger. The primary system used in this study performed well overall. The initial favorable results ofmore » this study warrant further investigation of direct contact heat exchange as a means of utilizing geothermal energy.« less

Babies and bearded dragons: sudden increase in reptile-associated Salmonella enterica serovar Tennessee infections, Germany 2008.

PubMed

Weiss, Bettina; Rabsch, Wolfgang; Prager, Rita; Tietze, Erhard; Koch, Judith; Mutschmann, Frank; Roggentin, Peter; Frank, Christina

2011-09-01

In 2008 a marked increase in Salmonella enterica serovar Tennessee infections in infants occurred in Germany. In March and April 2008, eight cases were notified compared to a median of 0-1 cases in 2001-2006. We carried out an investigation including a case-control study to identify the source of infection. A patient was a child < 3 years of age with Salmonella Tennessee isolated from stool from September 1, 2007, through December 31, 2008, identified through the national surveillance system. A control was a child with a notified rotavirus infection in the matching district, frequency matched by age group. We conducted telephone interviews on feeding, herbal infusions, and animal contact. Matched odds ratios (mOR) were calculated using exact conditional logistic regression. For Salmonella Tennessee isolates, pulsed-field gel electrophoresis and multiple-locus variable number tandem repeat analysis were performed. Further cloacal swab samples of reptiles kept in case households were investigated. We identified 18 cases < 3 years. Ten children were male; median age was 3 months (1-32 months). In 8 of 16 case households reptiles were kept. Direct contact between child and reptile was denied. Other forms of reptile contact were reported in four of the remaining eight households. Ten case- and 21 control-patients were included in the study. Only keeping of a reptile and "any reptile contact" were associated with Salmonella Tennessee infection (mOR 29.0; 95% CI 3.1 ± ∞ and mOR 119.5; 95% CI 11.7 - ∞). Identical Salmonella Tennessee strains of child and reptile kept in the same household could be shown in 2 cases. Reptiles were the apparent source of Salmonella Tennessee infection in these infants. Indirect contact between infants and reptiles seems to be sufficient to cause infection and should therefore be avoided.

The Setting Time of Polyether Impression Materials after Contact with Conventional and Experimental Gingival Margin Displacement Agents.

PubMed

Nowakowska, Danuta; Raszewski, Zbigniew; Ziętek, Marek; Saczko, Jolanta; Kulbacka, Julita; Więckiewicz, Włodzimierz

2018-02-01

The compatibility of chemical gingival margin displacement agents with polyether impression materials has not been determined. The aim of this study was to evaluate the setting time of polyether impression elastomers after contact with conventional and experimental gingival displacement agents. The study compared the setting time of two polyether impression materials: medium body (Impregum Penta Soft) and light body (Impregum Garant L DuoSoft) after contact with 10 gingival displacement agents, including 5 conventional astringents (10%, 20%, and 25% aluminum chloride, 25% aluminum sulfate, and 15.5% ferric sulfate) and 5 experimental adrenergics (0.1% and 0.01% HCl-epinephrine, 0.05% HCl-tetrahydrozoline, 0.05% HCl-oxymetazoline, and 10% HCl-phenylephrine). As many as 120 specimens (60 light body and 60 medium body) were mixed with 20 μl of each of 10 gingival displacement agents, and the time to achieve maximum viscosity was measured with a viscometer. The setting times of these specimens were compared with the control group of 12 specimens, which were polymerized without contact with the displacement agents. The experiments were performed in two environments: 23°C and 37°C (± 0.1°C). Individual and average polymerization time compatibility indices (PTCI) were calculated. Data were analyzed by 2-way ANOVA (α = 0.05). The evaluated chemical displacement agents from both groups changed the setting time of light- and medium-body PE. The negative individual PTCI values achieved astringent (20% aluminum chloride) with two PE in both temperature environments. The average PTCI values of the experimental displacement agents at laboratory and intraoral temperatures were significantly higher than the conventional agents. The present findings suggest that experimental retraction agents can be recommended clinically as gingival margin displacement agents with minimal effects on the setting time of medium- and light-body polyether impression materials; however, direct contact of chemical displacement agents and polyether impression materials can be avoided. © 2016 by the American College of Prosthodontists.

Radiofrequency energy antenna coupling to common laparoscopic instruments: practical implications.

PubMed

Jones, Edward L; Robinson, Thomas N; McHenry, Jennifer R; Dunn, Christina L; Montero, Paul N; Govekar, Henry R; Stiegmann, Greg V

2012-11-01

Electromagnetic coupling can occur between the monopolar "Bovie" instrument and other laparoscopic instruments without direct contact by a phenomenon termed antenna coupling. The purpose of this study was to determine if, and to what extent, radiofrequency energy couples to other common laparoscopic instruments and to describe practical steps that can minimize the magnitude of antenna coupling. In a laparoscopic simulator, monopolar radiofrequency energy was delivered to an L-hook. The tips of standard, nonelectrical laparoscopic instruments (either an unlit 10 mm telescope or a 5 mm grasper) were placed adjacent to bovine liver tissue and were never in contact with the active electrode. Thermal imaging quantified the change in tissue temperature nearest the tip of the telescope or grasper at the end of a 5 s activation of the active electrode. A 5 s activation (30 watts, coagulation mode, 4 cm separation between instruments) increased tissue temperature compared with baseline adjacent to the grasper tip (2.2 ± 2.2 °C; p = 0.013) and telescope tip (38.2 ± 8.0 °C; p < 0.001). The laparoscopic telescope tip increased tissue temperature more than the laparoscopic grasper tip (p < 0.001). Lowering the generator power from 30 to 15 Watts decreased the heat generated at the telescope tip (38.2 ± 8.0 vs. 13.5 ± 7.5 °C; p < 0.001). Complete separation of the camera/light cords and the active electrode cord decreased the heat generated near the telescope tip compared with parallel bundling of the cords (38.2 ± 8.0 vs. 15.7 ± 11.6 °C; p < 0.001). Commonly used laparoscopic instruments couple monopolar radiofrequency energy without direct contact with the active electrode, a phenomenon that results in heat transfer from a nonelectrically active instrument tip to adjacent tissue. Practical steps to minimize heat transfer resulting from antenna coupling include reducing the monopolar generator power setting and avoiding of parallel bundling of the telescope and active electrode cords.

Transmissibility and Pathogenicity of Ebola Virus: A Systematic Review and Meta-analysis of Household Secondary Attack Rate and Asymptomatic Infection

PubMed Central

Dean, Natalie E.; Halloran, M. Elizabeth; Yang, Yang; Longini, Ira M.

2016-01-01

Factors affecting our ability to control an Ebola outbreak include transmissibility of the virus and the proportion of transmissions occurring asymptomatically. We performed a meta-analysis of Ebola household secondary attack rate (SAR), disaggregating by type of exposure (direct contact, no direct contact, nursing care, direct contact but no nursing care). The estimated overall household SAR is 12.5% (95% confidence interval [CI], 8.6%–16.3%). Transmission was driven by direct contact, with little transmission occurring in its absence (SAR, 0.8% [95% CI, 0%–2.3%]). The greatest risk factor was the provision of nursing care (SAR, 47.9% [95% CI, 23.3%–72.6%]). There was evidence of a decline in household SAR for direct contact between 1976 and 2014 (P = .018). We estimate that 27.1% (95% CI, 14.5%–39.6%) of Ebola infections are asymptomatic. Our findings suggest that surveillance and containment measures should be effective for controlling Ebola. PMID:26932131

A Single-Material Logical Junction Based on 2D Crystal PdS2.

PubMed

Ghorbani-Asl, Mahdi; Kuc, Agnieszka; Miró, Pere; Heine, Thomas

2016-02-03

A single-material logical junction with negligible contact resistance is designed by exploiting quantum-confinement effects in 1T PdS2 . The metallic bilayer serves as electrodes for the semiconducting channel monolayer, avoiding contact resistance. Heat dissipation is then governed by tunnel loss, which becomes negligible at channel lengths larger than 2.45 nm. This value marks the integration limit for a conventional 2D transistor. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Army Physical Readiness Training

DTIC Science & Technology

2010-03-01

The lower leg pad is adjusted to contact the lower legs just above the ankle , allowing the lower leg to be fully extended, but not locked. The lower...contacts the lower legs just behind the ankles .  The hips, low back, shoulders, and head are firmly against the seat back.  Maintain a natural arch in...count 1 and inhale on count 2. Precautions: Avoid flexing or extending the trunk. Do not allow the ankles to turn in or out. C hapter 6 6-40 T C 3

Impact of shock wave pattern and cavitation bubble size on tissue damage during ureteroscopic electrohydraulic lithotripsy.

PubMed

Vorreuther, R; Corleis, R; Klotz, T; Bernards, P; Engelmann, U

1995-03-01

It is known that electrohydraulic lithotripsy (EHL) during ureteroscopy may cause ureteral damage. To evaluate this trauma potential, find its mechanism and make it possible to avoid it, our research employed photographic evaluation, tissue studies, shock wave measurements and disintegration tests. The setup included a 3.3 F probe attached to an experimental generator with adjustable voltages and capacities providing energies from 25 mJ. to 1300 mJ. per pulse. In general, we distinguish between two traumatic mechanisms: (1) After placing the probe directly on the mucosa the rapid initial plasma penetrates the tissue resulting in a small, nonthermal, punched-like defect, whose depth depends on the energy applied. This trauma has minor clinical implications and is avoided by maintaining a minimum safety distance of 1 mm.; (2) According to physics, each plasma is followed by a cavitation bubble. The maximum size of this bubble depends on the energy applied and ranges from 3 mm. (25 mJ) to > 15 mm. (1300 mJ). In proportion to the bubble size, the ureteral wall may be distended or disrupted, even when the probe is not in direct contact with the mucosa. Therefore, the goal should be to obtain a low energy pressure pulse with high disintegration efficacy. Our evaluation of the pressure waves revealed that the selection of a high voltage and a low capacity leads to short and steep "laser-like" pulses. These pulses have a significant higher impact on stone disintegration than the broader pulses of the same energy provided by currently available generators.

Convective heat transfer measurements in a vapour-liquid-liquid three-phase direct contact heat exchanger

NASA Astrophysics Data System (ADS)

Mahood, Hameed B.; Campbell, A. N.; Baqir, Ali Sh.; Sharif, A. O.; Thorpe, R. B.

2018-06-01

Energy usage is increasing around the world due to the continued development of technology, and population growth. Solar energy is a promising low-grade energy resource that can be harvested and utilised in different applications, such solar heater systems, which are used in both domestic and industrial settings. However, the implementation of an efficient energy conversion system or heat exchanger would enhance such low-grade energy processes. The direct contact heat exchanger could be the right choice due to its ability to efficiently transfer significant amounts of heat, simple design, and low cost. In this work, the heat transfer associated with the direct contact condensation of pentane vapour bubbles in a three-phase direct contact condenser is investigated experimentally. Such a condenser could be used in a cycle with a solar water heater and heat recovery systems. The experiments on the steady state operation of the three-phase direct contact condenser were carried out using a short Perspex tube of 70 cm in total height and an internal diameter of 4 cm. Only a height of 48 cm was active as the direct contact condenser. Pentane vapour, (the dispersed phase) with three different initial temperatures (40° C, 43.5° C and 47.5° C) was directly contacted with water (the continuous phase) at 19° C. The experimental results showed that the total heat transfer rate per unit volume along the direct contact condenser gradually decreased upon moving higher up the condenser. Additionally, the heat transfer rate increases with increasing mass flow rate ratio, but no significant effect on the heat transfer rate of varying the initial temperature of the dispersed phase was seen. Furthermore, both the outlet temperature of the continuous phase and the void fraction were positively correlated with the total heat transfer rate per unit volume, with no considerable effect of the initial temperature difference between the dispersed and continuous phases.

Convective heat transfer measurements in a vapour-liquid-liquid three-phase direct contact heat exchanger

NASA Astrophysics Data System (ADS)

Mahood, Hameed B.; Campbell, A. N.; Baqir, Ali Sh.; Sharif, A. O.; Thorpe, R. B.

2017-12-01

Energy usage is increasing around the world due to the continued development of technology, and population growth. Solar energy is a promising low-grade energy resource that can be harvested and utilised in different applications, such solar heater systems, which are used in both domestic and industrial settings. However, the implementation of an efficient energy conversion system or heat exchanger would enhance such low-grade energy processes. The direct contact heat exchanger could be the right choice due to its ability to efficiently transfer significant amounts of heat, simple design, and low cost. In this work, the heat transfer associated with the direct contact condensation of pentane vapour bubbles in a three-phase direct contact condenser is investigated experimentally. Such a condenser could be used in a cycle with a solar water heater and heat recovery systems. The experiments on the steady state operation of the three-phase direct contact condenser were carried out using a short Perspex tube of 70 cm in total height and an internal diameter of 4 cm. Only a height of 48 cm was active as the direct contact condenser. Pentane vapour, (the dispersed phase) with three different initial temperatures (40° C, 43.5° C and 47.5° C) was directly contacted with water (the continuous phase) at 19° C. The experimental results showed that the total heat transfer rate per unit volume along the direct contact condenser gradually decreased upon moving higher up the condenser. Additionally, the heat transfer rate increases with increasing mass flow rate ratio, but no significant effect on the heat transfer rate of varying the initial temperature of the dispersed phase was seen. Furthermore, both the outlet temperature of the continuous phase and the void fraction were positively correlated with the total heat transfer rate per unit volume, with no considerable effect of the initial temperature difference between the dispersed and continuous phases.

Binding Direction-Based Two-Dimensional Flattened Contact Area Computing Algorithm for Protein-Protein Interactions.

PubMed

Kang, Beom Sik; Pugalendhi, GaneshKumar; Kim, Ku-Jin

2017-10-13

Interactions between protein molecules are essential for the assembly, function, and regulation of proteins. The contact region between two protein molecules in a protein complex is usually complementary in shape for both molecules and the area of the contact region can be used to estimate the binding strength between two molecules. Although the area is a value calculated from the three-dimensional surface, it cannot represent the three-dimensional shape of the surface. Therefore, we propose an original concept of two-dimensional contact area which provides further information such as the ruggedness of the contact region. We present a novel algorithm for calculating the binding direction between two molecules in a protein complex, and then suggest a method to compute the two-dimensional flattened area of the contact region between two molecules based on the binding direction.

Eye Contact Facilitates Awareness of Faces during Interocular Suppression

ERIC Educational Resources Information Center

Stein, Timo; Senju, Atsushi; Peelen, Marius V.; Sterzer, Philipp

2011-01-01

Eye contact captures attention and receives prioritized visual processing. Here we asked whether eye contact might be processed outside conscious awareness. Faces with direct and averted gaze were rendered invisible using interocular suppression. In two experiments we found that faces with direct gaze overcame such suppression more rapidly than…

Influence of axial self-magnetic field component on arcing behavior of spiral-shaped contacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, Dingyu; Xiu, Shixin, E-mail: xsx@mail.xjtu.edu.cn; Wang, Yi

2015-10-15

The transverse magnetic field (TMF) contact design is commonly used in vacuum interrupters. When arcing occurs between the TMF contacts, the contact structure can create a self-induced magnetic field that drives the arc to move and rotate on the contact, and thus local overheating and severe erosion can be avoided. However, TMF contacts could also create an axial self-magnetic component, and the influence of this component on the arc behavior has not been considered to date. In this paper, five different types of Cu-Cr spiral-shaped TMF contacts with three different structures are investigated in a demountable vacuum chamber that containsmore » a high-speed charge-coupled device video camera. It was found that the contact structure greatly influenced the arc behavior, especially in terms of arc rotation and the effective contact area, while contacts with the same slot structure but different diameters showed similar arc behavior and arc motion. The magnetic field distribution and the Lorentz force of each of the three different contact structures are simulated, and the axial self-magnetic field was first taken into consideration for investigation of the TMF contact design. It was found that contact designs that have higher axial self-magnetic field components tend to have arc columns with larger diameters and show poorer arc motion and rotation performance in the experiments.« less

Curiosity Drill in Place for Load Testing Before Drilling

NASA Image and Video Library

2013-01-28

The percussion drill in the turret of tools at the end of the robotic arm of NASA Mars rover Curiosity has been positioned in contact with the rock surface in this image from the rover front Hazard-Avoidance Camera Hazcam.

75 FR 10250 - Kasugamycin; Receipt of Application for Emergency Exemption, Solicitation of Public Comment

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-05

... website is an ``anonymous access'' system, which means EPA will not know your identity or contact... files should avoid the use of special characters, any form of encryption, and be free of any defects or...

75 FR 51048 - Notice of Receipt of Request to Voluntarily Cancel a Pesticide Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-18

... website is an ``anonymous access'' system, which means EPA will not know your identity or contact... files should avoid the use of special characters, any form of encryption, and be free of any defects or...

Development of 3D online contact measurement system for intelligent manufacturing based on stereo vision

NASA Astrophysics Data System (ADS)

Li, Peng; Chong, Wenyan; Ma, Yongjun

2017-10-01

In order to avoid shortcomings of low efficiency and restricted measuring range exsited in traditional 3D on-line contact measurement method for workpiece size, the development of a novel 3D contact measurement system is introduced, which is designed for intelligent manufacturing based on stereo vision. The developed contact measurement system is characterized with an intergarted use of a handy probe, a binocular stereo vision system, and advanced measurement software.The handy probe consists of six track markers, a touch probe and the associated elcetronics. In the process of contact measurement, the hand probe can be located by the use of the stereo vision system and track markers, and 3D coordinates of a space point on the workpiece can be mearsured by calculating the tip position of a touch probe. With the flexibility of the hand probe, the orientation, range, density of the 3D contact measurenent can be adptable to different needs. Applications of the developed contact measurement system to high-precision measurement and rapid surface digitization are experimentally demonstrated.

Properties of knotted ring polymers. I. Equilibrium dimensions.

PubMed

Mansfield, Marc L; Douglas, Jack F

2010-07-28

We report calculations on three classes of knotted ring polymers: (1) simple-cubic lattice self-avoiding rings (SARs), (2) "true" theta-state rings, i.e., SARs generated on the simple-cubic lattice with an attractive nearest-neighbor contact potential (theta-SARs), and (3) ideal, Gaussian rings. Extrapolations to large polymerization index N imply knot localization in all three classes of chains. Extrapolations of our data are also consistent with conjectures found in the literature which state that (1) R(g)-->AN(nu) asymptotically for ensembles of random knots restricted to any particular knot state, including the unknot; (2) A is universal across knot types for any given class of flexible chains; and (3) nu is equal to the standard self-avoiding walk (SAW) exponent (congruent with 0.588) for all three classes of chains (SARs, theta-SARs, and ideal rings). However, current computer technology is inadequate to directly sample the asymptotic domain, so that we remain in a crossover scaling regime for all accessible values of N. We also observe that R(g) approximately p(-0.27), where p is the "rope length" of the maximally inflated knot. This scaling relation holds in the crossover regime, but we argue that it is unlikely to extend into the asymptotic scaling regime where knots become localized.

Mass transfer of hydrophobic organic chemicals between silicone sheets and through plant leaves and low-density polyethylene.

PubMed

Ahmadi, Hamid; Bolinius, Damien Johann; Jahnke, Annika; MacLeod, Matthew

2016-12-01

Plant leaves play an important role in the fate of hydrophobic organic contaminants (HOCs) in the environment. Yet much remains unknown about the permeability of leaves by HOCs. In this pilot study we measured (i) the kinetics of mass transfer of three polycyclic aromatic hydrocarbons (PAHs) and six polychlorinated biphenyls between a spiked and an unspiked sheet of polydimethylsiloxane (PDMS) in direct contact with each other for 24 h and (ii) kinetics of mass transfer of two PAHs through leaves and low-density polyethylene (LDPE) in a passive dosing experiment by inserting these matrices between the two sheets of PDMS for 48 h. The kinetics of mass transfer of fluoranthene between PDMS sheets in direct contact were a factor of 12 slower than those reported in the literature. The kinetics of mass transfer of fluorene and phenanthrene through leaves were within the range of those previously reported for 2,4-dichlorophenoxyacetic acid through isolated cuticles. Our results provide a proof-of-concept demonstration that the passive dosing method applied in this study can be used to measure the mass transfer coefficients of organic chemicals through leaves. Key recommendations for future experiments are to load the PDMS at the highest feasible concentrations to avoid working at analyte levels close to the limit of detection, to keep the leaves moist and to minimize potential pathways for contamination of the PDMS sheets by exposure to laboratory air. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Stray voltage and milk quality: a review.

PubMed

Reinemann, Douglas J

2012-07-01

If animal contact voltage reaches sufficient levels, animals coming into contact with grounded devices may receive a mild electric shock that can cause a behavioral response. At voltage levels that are just perceptible to the animal, behaviors indicative of perception (eg, flinches) may result with little change in normal routines. At higher exposure levels, avoidance behaviors may result. The direct effect of animal contact with electrical current can range from: • Mild behavioral reactions indicative of sensation, to • Involuntary muscle contraction, or twitching, to • Intense behavioral responses indicative of pain. The indirect effects of these behaviors can vary considerably depending on the specifics of the contact location, level of current flow, body pathway, frequency of occurrence, and many other factors related to the daily activities of animals. There are several common situations of concern in animal environments: • Animals avoiding certain exposure locations, which may result in: X Reduced water intake if exposure is required for animals to access watering devices, X Reduced feed intake if exposure is required for animals to accesses feeding devices or locations. • Difficulty of moving or handling animals in areas of voltage/current exposure• The physiologic implications of the release of stress hormones produced by contact with painful stimuli. The severity of response will depend on the amount of electrical current (measured in milliamps) flowing through the animal’s body, the pathway it takes through the body, and the sensitivity of the individual animal. The results of the combined current dose-response experiments, voltage exposure response experiments, and measurements of body and contact resistances is consistent with the lowest (worst case) cow + contact resistance as low as 500 as estimated by Lefcourt that may occur in some unusual situations on farms (firm application of the muzzle to a wet metallic watering device and hoof contact on a clean, wet, contoured metallic plate on the floor). These studies on responses of dairy cows to electrical exposure agree well with each other and with predictions from neuroelectric theory and practice. There is a high degree of repeatability across studies in which exposures and responses have been appropriately quantified. For confirmation, a potential of 2 to 4 V (60 Hz, rms) must be measured between 2 points that an animal might contact (or animal contact measurement), and some animals should exhibit signs of avoidance behavior. The animal contact voltage measurement with an appropriate shunt resistor value provides the only reliable indication of exposure levels. Voltage readings at cow contact points should be made with a 500- or 1000- resistor across the 2 measuring leads to the cow contact points in addition to open circuit measurements. The only studies that have documented adverse effects of voltage and current on cows had both sufficient current applied to cause aversion and forced exposures (ie, animals could not eat or drink without being exposed to voltage and current) and all of the indirect responses (reduced water or intake and milk production) were behaviorally mediated. It is typical for voltage levels to vary considerably at different locations on a farm. Decreased water and/or feed intake or undesired behaviors result only if current levels are sufficient to produce aversion at locations that are critical to daily animal activity, such as feeders, waterers, and milking areas. If an aversive current occurs only a few times per day, it is not likely to have an adverse effect on cow behavior. The more often an aversive voltage occurs in areas critical to cows’ normal feeding, drinking, or resting, the more likely it is to affect cows. A number of studies have been done to investigate potential detrimental physiologic responses that may result from animals’ exposure to voltage and current. The literature review presented here summarizes 46 research trials on groups of cows exposed to know levels of voltage and/or current. Many of these were part of the same experiment but exposed cows at different levels of voltage or current. None of these trials or experiments (some using aggressive exposure of cows to mastitis organisms) showed a significant effect of voltage/current exposure on SCC or the incidence of mastitis. Many of these studies showed behavioral modification and some showed minor changes in milk yield, milk composition, or stress hormones (especially cortisol). These studies have shown that increased concentrations of the stress hormone cortisol do not occur at levels below behavioral response levels and only become apparent in some, but not all, cows at substantially higher voltage/current exposures than the threshold required for behavioral modification. This body of research indicates that while exposure to stray voltage at levels of 2 V to 4 V may be a mild stressor to dairy cows, it does not contribute to increased SCC or incidence of mastitis or reduced milk yield.

Avoidance threshold to oil water-soluble fraction by a juvenile marine teleost fish.

PubMed

Claireaux, Guy; Quéau, Pierre; Marras, Stefano; Le Floch, Stéphane; Farrell, Anthony P; Nicolas-Kopec, Annabelle; Lemaire, Philippe; Domenici, Paolo

2018-03-01

When oil spills occur, behavior is the first line of defense for a fish to avoid being contaminated. We determined the avoidance threshold of the European seabass (Dicentrarchus labrax) to the water-soluble fraction (WSF) of oil using a dual-flow choice box. The results showed that a plume of 20%-diluted WSF (total polycyclic aromatic hydrocarbon [PAH] concentration: 8.54 μg L -1 ) triggered a significant avoidance response that was detected within 7.5 min of introducing WSF-contaminated water into the experimental setup. However, the ecological relevance of seabass capacity to detect and avoid WSF remains to be established. In the short term, such a response is indeed liable to reduce seabass contact time with oil-contaminated water and thus preserve their functional integrity. In the long term, however, avoidance may contribute to the displacement of a population into a possibly less auspicious environment, with consequences very similar to those of contaminant exposure, that is, disturbed population dynamics and demography. Environ Toxicol Chem 2018;37:854-859. © 2017 SETAC. © 2017 SETAC.

Accessing inoculation methods of maize and wheat with Azospirillum brasilense.

PubMed

Fukami, Josiane; Nogueira, Marco Antonio; Araujo, Ricardo Silva; Hungria, Mariangela

2016-03-01

The utilization of inoculants containing Azospirillum is becoming more popular due to increasing reports of expressive gains in grain yields. However, incompatibility with pesticides used in seed treatments represents a main limitation for a successful inoculation. Therefore, in this study we searched for alternatives methods for seed inoculation of maize and wheat, aiming to avoid the direct contact of bacteria with pesticides. Different doses of inoculants containing Azospirillum brasilense were employed to perform inoculation in-furrow, via soil spray at sowing and via leaf spray after seedlings had emerged, in comparison to seed inoculation. Experiments were conducted first under greenhouse controlled conditions and then confirmed in the field at different locations in Brazil. In the greenhouse, most parameters measured responded positively to the largest inoculant dose used in foliar sprays, but benefits could also be observed from both in-furrow and soil spray inoculation. However, our results present evidence that field inoculation with plant-growth promoting bacteria must consider inoculant doses, and point to the need of fine adjustments to avoid crossing the threshold of growth stimulation and inhibition. All inoculation techniques increased the abundance of diazotrophic bacteria in plant tissues, and foliar spray improved colonization of leaves, while soil inoculations favored root and rhizosphere colonization. In field experiments, inoculation with A. brasilense allowed for a 25 % reduction in the need for N fertilizers. Our results have identified alternative methods of inoculation that were as effective as the standard seed inoculation that may represent an important strategy to avoid the incompatibility between inoculant bacteria and pesticides employed for seed treatment.

Smells Like Home: Chemically Mediated Co-Habitation of Two Termite Species in a Single Nest.

PubMed

Jirošová, Anna; Sillam-Dussès, David; Kyjaková, Pavlína; Kalinová, Blanka; Dolejšová, Klára; Jančařík, Andrej; Majer, Pavel; Cristaldo, Paulo Fellipe; Hanus, Robert

2016-10-01

Termite nests often are referred to as the most elaborate constructions of animals. However, some termite species do not build a nest at all and instead found colonies inside the nests of other termites. Since these so-called inquilines do not need to be in direct contact with the host population, the two colonies usually live in separate parts of the nest. Adaptations of both the inquiline and its host are likely to occur to maintain the spatial exclusion and reduce the costs of potential conflicts. Among them, mutual avoidance, based on chemical cues, is expected. We investigated chemical aspects of cohabitation between Constrictotermes cavifrons (Nasutitermitinae) and its obligatory inquiline Inquilinitermes inquilinus (Termitinae). Inquiline soldiers produce in their frontal glands a blend of wax esters, consisting of the C 12 alcohols (3Z)-dodec enol, (3Z,6Z)-dodecadienol, and dodecanol, esterified with different fatty acids. The C 12 alcohols appear to be cleaved gradually from the wax esters, and they occur in the frontal gland, in soldier headspace, and in the walls of the inquiline part of the nest. Electrophysiological experiments revealed that (3Z)-dodecenol and (3Z,6Z)-dodecadienol are perceived by workers of both species. Bioassays indicated that inquiline soldier heads, as well as the two synthetic compounds, are attractive to conspecific workers and elicit an arresting behavior, while host soldiers and workers avoid these chemicals at biologically relevant amounts. These observations support the hypothesis that chemically mediated spatial separation of the host and the inquiline is an element of a conflict-avoidance strategy in these species.

Volatile secondary metabolites as aposematic olfactory signals and defensive weapons in aquatic environments

PubMed Central

Giordano, Giuseppe; Carbone, Marianna; Ciavatta, Maria Letizia; Silvano, Eleonora; Gavagnin, Margherita; Garson, Mary J.; Cheney, Karen L.; Mudianta, I Wayan; Russo, Giovanni Fulvio; Villani, Guido; Magliozzi, Laura; Zidorn, Christian; Cutignano, Adele; Fontana, Angelo; Ghiselin, Michael T.

2017-01-01

Olfaction is considered a distance sense; hence, aquatic olfaction is thought to be mediated only by molecules dissolved in water. Here, we challenge this view by showing that shrimp and fish can recognize the presence of hydrophobic olfactory cues by a “tactile” form of chemoreception. We found that odiferous furanosesquiterpenes protect both the Mediterranean octocoral Maasella edwardsi and its specialist predator, the nudibranch gastropod Tritonia striata, from potential predators. Food treated with the terpenes elicited avoidance responses in the cooccurring shrimp Palaemon elegans. Rejection was also induced in the shrimp by the memory recall of postingestive aversive effects (vomiting), evoked by repeatedly touching the food with chemosensory mouthparts. Consistent with their emetic properties once ingested, the compounds were highly toxic to brine shrimp. Further experiments on the zebrafish showed that this vertebrate aquatic model also avoids food treated with one of the terpenes, after having experienced gastrointestinal malaise. The fish refused the food after repeatedly touching it with their mouths. The compounds studied thus act simultaneously as (i) toxins, (ii) avoidance-learning inducers, and (iii) aposematic odorant cues. Although they produce a characteristic smell when exposed to air, the compounds are detected by direct contact with the emitter in aquatic environments and are perceived at high doses that are not compatible with their transport in water. The mouthparts of both the shrimp and the fish have thus been shown to act as “aquatic noses,” supporting a substantial revision of the current definition of the chemical senses based upon spatial criteria. PMID:28289233

Contact angle control of sessile drops on a tensioned web

NASA Astrophysics Data System (ADS)

Park, Janghoon; Kim, Dongguk; Lee, Changwoo

2018-04-01

In this study, the influence of the change of tension applied to flexible and thin web substrate on the contact angle of sessile drop in roll-to-roll system was investigated. Graphene oxide and deionized water solutions were used in the experiments. Tension was changed to 29, 49, and 69 N, and the casting distance of the micropipette and the material was set to 10, 20, and 40 mm, and the droplet volume was set to 10, 20, and 30 μL, respectively. Statistical analysis of three variables and analysis of the variance methodology showed that the casting distance was most significant for the contact angle change, and the most interesting tension variable was also affected. The change in tension caused the maximum contact angle to change by 5.5°. The tension was not uniform in the width direction. When the droplet was applied in the same direction in the width direction, it was confirmed that the tension unevenness had great influence on the contact angle up to 11°. Finally, the casting distance, which has a large effect on the contact angle, was calibrated in the width direction to reduce the width direction contact angle deviation to 1%. This study can be applied to fine patterning research using continuous inkjet printing and aerosol jet printing, which are roll-to-roll processes based on droplet handling.

Negative emotions and emotional eating: the mediating role of experiential avoidance.

PubMed

Litwin, Rachel; Goldbacher, Edie M; Cardaciotto, LeeAnn; Gambrel, Laura Eubanks

2017-03-01

Emotional eating is a risk factor for eating pathology across the life- and weight-span. Research demonstrates that negative emotions are a precipitant of emotional eating, particularly among female college students. However, the underlying factors that explain this relationship are unclear. Experiential avoidance, a propensity toward being unwilling to remain in contact with aversive private experiences, may explain the association between negative emotions and emotional eating. The purpose of this study was to examine whether experiential avoidance would mediate the association between negative emotions and emotional eating. A sample of 132 women (17.4 % African American, 59.8 % White) completed measures of mood, experiential avoidance and emotional eating. Bias-corrected bootstrapping mediational analyses were conducted. Experiential avoidance mediated the relationship between negative emotions and emotional eating b = -0.21, 95 % BC CI [-0.43, -0.07]. The indirect effect through experiential avoidance accounted for 9 % of the variance, which represents a medium effect (k 2  = 0.09, 95 % BC CI [0.03, 0.18]). Results suggest that experiential avoidance is important for understanding the relationship between negative emotions and emotional eating and may inform potential strategies for prevention and treatment.

Fabrication of an Aluminum Based Hot Electron Mixer for Terahertz Applications

NASA Technical Reports Server (NTRS)

Echternach, P. M.; LeDuc, H. G.; Skalare, A.; McGrath, W. R.

2000-01-01

Aluminum based diffusion cooled hot electron bolometers (HEB) mixers, predicted to have better noise, bandwidth and to require less LO power than Nb based diffusion cooled HEBs, have been fabricated. Preliminary DC tests were performed. The bolometer elements consisted of short (0.1 to 0.3 micron), narrow (0.08 to 0. 15 micron) and thin (11 nm) aluminum wires connected to large contact pads consisting of a novel trilayer Al/Ti/Au. The patterns were defined by electron beam lithography and the metal deposition involved a double angle process, the Aluminum wires being deposited straight on and the pads being deposited at a 45 degree angle without breaking vacuum. The Al/Ti/Au trilayer was developed to provide a way of making contact between the aluminum wire and the gold antenna. The Titanium layer acts as a diffusion barrier to avoid damage of the Aluminum contact and bolometer wire and to lower the transition temperature of the pads to below that of the bolometer wire. The Au layer avoids the formation of an oxide on the Ti layer and provides good electrical contact to the IF/antenna structure. The resistance of the bolometers as a function of temperature was measured. It is clear that below the transition temperature of the wire (1.8K) but above the transition temperature of the contact pads (0.6K), the proximity effect drives most of the bolometer wire normal, causing a very broad transition. This effect should not affect the performance of the bolometers since they will be operated at a temperature below the TC of the pads. This is evident from the IV characteristics measured at 0.3K. RF characterization tests will begin shortly.

Wettability and impact dynamics of water droplets on rice ( Oryza sativa L.) leaves

NASA Astrophysics Data System (ADS)

Kwon, Dae Hee; Huh, Hyung Kyu; Lee, Sang Joon

2014-03-01

We investigated the wettability and impact dynamics of water droplets on rice leaves at various leaf inclination angles and orientations. Contact angle, contact angle hysteresis (CAH), and roll-off angle ( α roll) of water droplets were measured quantitatively. Results showed that droplet motion exhibited less resistance along the longitudinal direction. Impact dynamic parameters, such as impact behaviors, maximum spreading factor, contact distance, and contact time were also investigated. Three different impact behaviors were categorized based on the normal component of Weber number irrespective of the inclination angle of the rice leaf. The asymmetric impact behavior induced by the tangential Weber number was also identified. Variation in the maximum spreading factor according to the normal Weber number was measured and compared with theoretical value obtained according to scaling law to show the wettability of the rice leaves. The contact distance of the impacting droplets depended on the inclination angle of the leaves. Along the longitudinal direction of rice leaves, contact distance was farther than that along the transverse direction. This result is consistent with the smaller values of CAH and α roll along the longitudinal direction.

Orally dissolving strips: A new approach to oral drug delivery system

PubMed Central

Bala, Rajni; Pawar, Pravin; Khanna, Sushil; Arora, Sandeep

2013-01-01

Recently, fast dissolving films are gaining interest as an alternative of fast dissolving tablets. The films are designed to dissolve upon contact with a wet surface, such as the tongue, within a few seconds, meaning the consumer can take the product without need for additional liquid. This convenience provides both a marketing advantage and increased patient compliance. As the drug is directly absorbed into systemic circulation, degradation in gastrointestinal tract and first pass effect can be avoided. These points make this formulation most popular and acceptable among pediatric and geriatric patients and patients with fear of choking. Over-the-counter films for pain management and motion sickness are commercialized in the US markets. Many companies are utilizing transdermal drug delivery technology to develop thin film formats. In the present review, recent advancements regarding fast dissolving buccal film formulation and their evaluation parameters are compiled. PMID:24015378

Personal Safety in Dangerous Places

PubMed Central

Williams, Terry; Dunlap, Eloise; Johnson, Bruce D.; Hamid, Ansley

2009-01-01

Personal safety during fieldwork is seldom addressed directly in the literature. Drawing from many prior years of ethnographic research and from field experience while studying crack distributors in New York City, the authors provide a variety of strategies by which ethnographic research can be safely conducted in dangerous settings. By projecting an appropriate demeanor, ethnographers can seek others for protector and locator roles, routinely create a safety zone in the field, and establish compatible field roles with potential subjects. The article also provides strategies for avoiding or handling sexual approaches, common law crimes, fights, drive-by shootings, and contacts with the police. When integrated with other standard qualitative methods, ethnographic strategies help to ensure that no physical harm comes to the field-worker and other staff members. Moreover, the presence of researchers may actually reduce (and not increase) potential and actual violence among crack distributors/abusers or others present in the field setting. PMID:19809525

A new device for dynamic sampling of radon in air

NASA Astrophysics Data System (ADS)

Lozano, J. C.; Escobar, V. Gómez; Tomé, F. Vera

2000-08-01

A new system is proposed for the active sampling of radon in air, based on the well-known property of activated charcoal to retain radon. Two identical carbon-activated cartridges arranged in series remove the radon from the air being sampled. The air passes first through a desiccant cell and then the carbon cartridges for short sampling times using a low-flow pump. The alpha activity for each cartridge is determined by a liquid scintillation counting system. The cartridge is placed in a holder into a vial that also contains the appropriate amount of scintillation cocktail, in a way that avoids direct contact between cocktail and charcoal. Once dynamic equilibrium between the phases has been reached, the vials can be counted. Optimum sampling conditions concerning flow rates and sampling times are determined. Using those conditions, the method was applied to environmental samples, straightforwardly providing good results for very different levels of activity.

[Prompt control of an imported carbapenem-resistant Acinetobacter baumanii outbreak in a French intensive care unit].

PubMed

Guth, C; Cavalli, Z; Pernod, C; Lhopital, C; Wey, Pf; Gerome, P; Turc, J

2016-01-01

to describe the management and control of a limited outbreak of carbapenem-resistant Acinetobacter baumanii (CRAB) outbreak in a French intensive care unit. Careful review of the contact's and carrier's files and outbreak management procedures. An undiagnosed CRAB carrier was admitted to our intensive care unit after medical evacuation from Turkey. Despite preventive isolation and contact precautions, a secondary case was diagnosed 5 days after admission of the index case and resulted in the creation of a crisis unit. Prompt management included an epidemiologic investigation with contact screening and follow-up, environmental screening, and additional restrictive measures: isolation room, closure of adjacent rooms, patient cohorting with designated nurses, and reinforcement of contact precautions. restrictive management of CRAB outbreaks may allow prompt outbreak control and avoid prolonged room closures.

Language Contact Means Language Conflict.

ERIC Educational Resources Information Center

Nelde, Peter H.

1987-01-01

Describes the characteristics of language conflict and examines the areas of emphasis in the literature, including multilingualism and linguistic identity, glottophagia and minority/majority relations, the danger of reliance on language censuses, conflict resolution/avoidance, and the importance of ecolinguistics in conflict description and for…

40 CFR 180.108 - Acephate; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

... establishments, including food service, manufacturing and processing establishments, such as restaurants... avoid atomization or splashing of the spray. Contamination of food or food-contact surfaces shall be... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.108...

40 CFR 180.435 - Deltamethrin; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

... in food handling establishments, including food service, manufacturing and processing establishments.... Contamination of food/feed or food/feed contact surfaces shall be avoided. (B) To assure safe use of the...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances...

40 CFR 180.442 - Bifenthrin; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

... application of bifenthrin in food handling establishments, including food service, manufacturing and... ingredient. Contamination of food/feed or food/feed contact surfaces shall be avoided. (B) To assure safe use...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances...

Direct-contact closed-loop heat exchanger

DOEpatents

Berry, Gregory F.; Minkov, Vladimir; Petrick, Michael

1984-01-01

A high temperature heat exchanger with a closed loop and a heat transfer liquid within the loop, the closed loop having a first horizontal channel with inlet and outlet means for providing direct contact of a first fluid at a first temperature with the heat transfer liquid, a second horizontal channel with inlet and outlet means for providing direct contact of a second fluid at a second temperature with the heat transfer liquid, and means for circulating the heat transfer liquid.

In vivo degradation effects of alloy MgNd2 in contact with mucous tissue.

PubMed

Seitz, J-M; Eifler, R; Weber, C; Lenarz, T H; Maier, H J; Durisin, M

2015-07-01

Magnesium alloys are currently being investigated for use as resorbable biomaterials. Various applications for magnesium based implant materials have already been presented. Currently, stents and structures that sustain diseased or narrowed vessels seem to be the most promising areas. This study focuses on the use of a magnesium fluoride (MgF2 ) coated magnesium neodymium based alloy (MgNd2 ) and its use as a postsurgery stent material to avoid proliferation in the sinus region. Simple cylindrical shaped specimens were sown to the sinus' mucosa of pigs and left in place for different periods of time to investigate the long-term corrosion resistance of the alloy and its coating during direct contact with physiological tissue. Investigations made within this study explicitly focused on the corrosive behavior of the alloy in the region of a physiological sinus. Thus, losses in mass and volume, and element analyses were considered to obtain information about the specimens' corrosion performance over time. Furthermore, micrographs support the alloy specific corrosion type analyses which focus on grain boundary effects. This study demonstrates the general in vivo applicability of fluoride coated MgNd2 . The progress of corrosion was determined to be adequate and homogeneous over a total period of 180 days. © 2014 Wiley Periodicals, Inc.

Automated Escape Guidance Algorithms for An Escape Vehicle

NASA Technical Reports Server (NTRS)

Flanary, Ronald; Hammen, David; Ito, Daigoro; Rabalais, Bruce; Rishikof, Brian; Siebold, Karl

2002-01-01

An escape vehicle was designed to provide an emergency evacuation for crew members living on a space station. For maximum escape capability, the escape vehicle needs to have the ability to safely evacuate a station in a contingency scenario such as an uncontrolled (e.g., tumbling) station. This emergency escape sequence will typically be divided into three events: The fust separation event (SEP1), the navigation reconstruction event, and the second separation event (SEP2). SEP1 is responsible for taking the spacecraft from its docking port to a distance greater than the maximum radius of the rotating station. The navigation reconstruction event takes place prior to the SEP2 event and establishes the orbital state to within the tolerance limits necessary for SEP2. The SEP2 event calculates and performs an avoidance burn to prevent station recontact during the next several orbits. This paper presents the tools and results for the whole separation sequence with an emphasis on the two separation events. The fust challenge includes collision avoidance during the escape sequence while the station is in an uncontrolled rotational state, with rotation rates of up to 2 degrees per second. The task of avoiding a collision may require the use of the Vehicle's de-orbit propulsion system for maximum thrust and minimum dwell time within the vicinity of the station vicinity. The thrust of the propulsion system is in a single direction, and can be controlled only by the attitude of the spacecraft. Escape algorithms based on a look-up table or analytical guidance can be implemented since the rotation rate and the angular momentum vector can be sensed onboard and a-priori knowledge of the position and relative orientation are available. In addition, crew intervention has been provided for in the event of unforeseen obstacles in the escape path. The purpose of the SEP2 burn is to avoid re-contact with the station over an extended period of time. Performing this maneuver properly requires knowledge of the orbital state, which is obtained during the navigation state reconstruction event. Since the direction of the delta-v of the SEPI maneuver is a random variable with respect to the Local Vertical Local Horizontal (LVLH) coordinate system, calculating the required SEP2 burn is a challenge. This problem was solved using a neural network as a model-free function approximation technique.

Fear of feces? Trade-offs between disease risk and foraging drive animal activity around raccoon latrines

USGS Publications Warehouse

Weinstein, Sara B.; Moura, Chad W.; Mendez, Jon Francis; Lafferty, Kevin D.

2017-01-01

Fear of predation alters prey behavior, which can indirectly alter entire landscapes. A parasite-induced ecology of fear might also exist if animals avoid parasite-contaminated resources when infection costs outweigh foraging benefits. To investigate whether animals avoid parasite contaminated sites, and if such avoidance balances disease costs and foraging gains, we monitored animal behavior at raccoon latrines – sites that concentrate both seeds and pathogenic parasite eggs. Using wildlife cameras, we documented over 40 potentially susceptible vertebrate species in latrines and adjacent habitat. Latrine contact rates reflected background activity, diet preferences and disease risk. Disease-tolerant raccoons and rats displayed significant site attraction, while susceptible birds and small mammals avoided these high-risk sites. This suggests that parasites, like predators, might create a landscape of fear for vulnerable hosts. Such non-consumptive parasite effects could alter disease transmission, population dynamics, and even ecosystem structure.

The 2014-2015 Pāhoa lava flow crisis at Kīlauea Volcano, Hawai‘i: Disaster avoided and lessons learned

USGS Publications Warehouse

Poland, Michael; Orr, Tim R.; Kauahikaua, James P.; Brantley, Steven R.; Babb, Janet L.; Patrick, Matthew R.; Neal, Christina; Anderson, Kyle R.; Antolik, Loren; Burgess, Matthew K.; Elias, Tamar; Fuke, Steven; Fukunaga, Pauline; Johanson, Ingrid; Kagimoto, Marian; Kamibayashi, Kevan P.; Lee, Lopaka; Miklius, Asta; Million, William; Moniz, Cyril J.; Okubo, Paul G.; Sutton, Andrew; Takahashi, T. Jane; Thelen, Weston A.; Tollett, Willam; Trusdell, Frank A.

2016-01-01

Lava flow crises are nothing new on the Island of Hawai‘i, where their destructive force has been demonstrated repeatedly over the past several hundred years. The 2014–2015 Pāhoa lava flow crisis, however, was unique in terms of its societal impact and volcanological characteristics. Despite low effusion rates, a long-lived lava flow whose extent reached 20 km (the longest at Kīlauea Volcano in the past several hundred years) was poised for months to impact thousands of people, although direct impacts were ultimately minor (thus far). Careful observation of the flow reaffirmed and expanded knowledge of the processes associated with pāhoehoe emplacement, including the direct correlation between summit pressurization and flow advance, the influence of existing geologic structures on flow pathways, and the possible relationship between effusion rate and flow length. Communicating uncertainty associated with lava flow hazards was a challenge throughout the crisis, but online distribution of information and direct contact with residents proved to be effective strategies for keeping the public informed and educated about flow progress and how lava flows work (including forecasting limitations). Volcanological and sociological lessons will be important for inevitable future lava flow crises in Hawai‘i and, potentially, elsewhere in the world.

78 FR 23940 - Use of International Standard ISO-10993, “Biological Evaluation of Medical Devices Part 1...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-23

... requests for medical devices that come into direct or indirect contact with the human body in order to... the human body in order to determine the potential toxicity resulting from contact of the component... direct or indirect contact with the human body. This document addresses the following issues: (1) Test...

Toxicity of aerosols to larch casebearer larvae

Treesearch

Robert L. Lyon; Margaret E. May

1970-01-01

Six insecticides were tested in the laboratory as aerosols against larch casebeare1 larvae. Their toxicity was determined by both direct contact and residual contact on filter paper. All six were highly toxic at less than 1.05 µg/ cm2 (the equivalent of 1.5 oz./acre). In decreasing order of toxicity at LD90 (direct contact...

Toxic Hazard to the Rabbit from Direct and Vapor Contact with HD-Contaminated Plexiglas, Concrete, or XM40 Nylon Carrier Material

DTIC Science & Technology

1986-07-01

for vapor transfer. A toxicological test was c’isigned to evaluate the above models. Animals were exposed to agant vapor and to direct contact with...surfaces contaminated with HD. If the toxicological response is the same from direct contact as from vapor, then only vapor transfer is significant...study were chosen to deter- mine whether partitioning is applicable to nonpermeable materials such as the polymethyl methacrylate ( PMMA ) sheeting or to

Direct-contact closed-loop heat exchanger

DOEpatents

Berry, G.F.; Minkov, V.; Petrick, M.

1981-11-02

A high temperature heat exchanger is disclosed which has a closed loop and a heat transfer liquid within the loop, the closed loop having a first horizontal channel with inlet and outlet means for providing direct contact of a first fluid at a first temperature with the heat transfer liquid, a second horizontal channel with inlet and outlet means for providing direct contact of a second fluid at a second temperature with the heat transfer liquid, and means for circulating the heat transfer liquid.

Direct determination of three-phase contact line properties on nearly molecular scale

DOE PAGES

Winkler, P. M.; McGraw, R. L.; Bauer, P. S.; ...

2016-05-17

Wetting phenomena in multi-phase systems govern the shape of the contact line which separates the different phases. For liquids in contact with solid surfaces wetting is typically described in terms of contact angle. While in macroscopic systems the contact angle can be determined experimentally, on the molecular scale contact angles are hardly accessible. Here we report the first direct experimental determination of contact angles as well as contact line curvature on a scale of the order of 1nm. For water nucleating heterogeneously on Ag nanoparticles we find contact angles around 15 degrees compared to 90 degrees for the corresponding macroscopicallymore » measured equilibrium angle. The obtained microscopic contact angles can be attributed to negative line tension in the order of –10 –10 J/m that becomes increasingly dominant with increasing curvature of the contact line. Furthermore, these results enable a consistent theoretical description of heterogeneous nucleation and provide firm insight to the wetting of nanosized objects.« less

Anisotropic forces from spatially constrained focal adhesions mediate contact guidance directed cell migration

PubMed Central

Ray, Arja; Lee, Oscar; Win, Zaw; Edwards, Rachel M.; Alford, Patrick W.; Kim, Deok-Ho; Provenzano, Paolo P.

2017-01-01

Directed migration by contact guidance is a poorly understood yet vital phenomenon, particularly for carcinoma cell invasion on aligned collagen fibres. We demonstrate that for single cells, aligned architectures providing contact guidance cues induce constrained focal adhesion maturation and associated F-actin alignment, consequently orchestrating anisotropic traction stresses that drive cell orientation and directional migration. Consistent with this understanding, relaxing spatial constraints to adhesion maturation either through reduction in substrate alignment density or reduction in adhesion size diminishes the contact guidance response. While such interactions allow single mesenchymal-like cells to spontaneously ‘sense' and follow topographic alignment, intercellular interactions within epithelial clusters temper anisotropic cell–substratum forces, resulting in substantially lower directional response. Overall, these results point to the control of contact guidance by a balance of cell–substratum and cell–cell interactions, modulated by cell phenotype-specific cytoskeletal arrangements. Thus, our findings elucidate how phenotypically diverse cells perceive ECM alignment at the molecular level. PMID:28401884

Contact lens design with slope-constrained Q-type aspheres for myopia correction

NASA Astrophysics Data System (ADS)

Peng, Wei-Jei; Cheng, Yuan-Chieh; Hsu, Wei-Yao; Yu, Zong-Ru; Ho, Cheng-Fang; Abou-El-Hossein, Khaled

2017-08-01

The design of the rigid contact lens (CL) with slope-constrained Q-type aspheres for myopia correction is presented in this paper. The spherical CL is the most common type for myopia correction, however the spherical aberration (SA) caused from the pupil dilation in dark leads to the degradation of visual acuity which cannot be corrected by spherical surface. The spherical and aspheric CLs are designed respectively based on Liou's schematic eye model, and the criterion is the modulation transfer function (MTF) at the frequency of 100 line pair per mm, which corresponds to the normal vision of one arc-minute. After optimization, the MTF of the aspheric design is superior to that of the spherical design, because the aspheric surface corrects the SA for improving the visual acuity in dark. For avoiding the scratch caused from the contact profilometer, the aspheric surface is designed to match the measurability of the interferometer. The Q-type aspheric surface is employed to constrain the root-mean-square (rms) slope of the departure from a best-fit sphere directly, because the fringe density is limited by the interferometer. The maximum sag departure from a best-fit sphere is also controlled according to the measurability of the aspheric stitching interferometer (ASI). The inflection point is removed during optimization for measurability and appearance. In this study, the aspheric CL is successfully designed with Q-type aspheres for the measurability of the interferometer. It not only corrects the myopia but also eliminates the SA for improving the visual acuity in dark based on the schematic eye model.

Process for upgrading arsenic-containing oils

DOEpatents

Sullivan, Richard F.

1979-01-01

A method is provided for avoiding feed-transfer-line plugging by a deposit comprising arsenic in hydroprocessing an oil containing an arsenic contaminant. In the method, a mixture of hydrogen gas and the oil is formed in situ in a bed of porous particulate contact material.

43 CFR 11.21 - Emergency restorations.

Code of Federal Regulations, 2011 CFR

2011-10-01

....21 Public Lands: Interior Office of the Secretary of the Interior NATURAL RESOURCE DAMAGE ASSESSMENTS... of a natural resource emergency, the natural resource trustee shall contact the National Response... requiring immediate action to avoid an irreversible loss of natural resources or to prevent or reduce any...

43 CFR 11.21 - Emergency restorations.

Code of Federal Regulations, 2010 CFR

2010-10-01

....21 Public Lands: Interior Office of the Secretary of the Interior NATURAL RESOURCE DAMAGE ASSESSMENTS... of a natural resource emergency, the natural resource trustee shall contact the National Response... requiring immediate action to avoid an irreversible loss of natural resources or to prevent or reduce any...

Gestalt Approaches to Conjoint Therapy

ERIC Educational Resources Information Center

Kelly, Brian J.; Gill, John D.

1978-01-01

An alternative to individual counseling is marriage and family counseling. It is the preferred mode of treatment for all but the social isolate. The specific methods by which persons avoid healthy contacts are discussed, as are counseling methodologies which are based on Gestalt and family systems theory. (Author)

75 FR 9896 - Maneb; Notice of Receipt of a Request to Voluntarily Cancel a Certain Pesticide Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-04

... website is an ``anonymous access'' system, which means EPA will not know your identity or contact... files should avoid the use of special characters, any form of encryption, and be free of any defects or...

76 FR 34937 - Amitraz, Bentazon, Bifenthrin, Chlorfenapyr, Cyfluthrin, Deltamethrin, et al

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-15

... production (NAICS code 112). Food manufacturing (NAICS code 311). Pesticide manufacturing (NAICS code 32532... food/feed handling establishments (including food service, manufacturing and processing establishments... ingredient; and contamination of food/ feed or food/feed contact surfaces shall be avoided. Compliance with...

Wound-Related Allergic/Irritant Contact Dermatitis.

PubMed

Alavi, Afsaneh; Sibbald, R Gary; Ladizinski, Barry; Saraiya, Ami; Lee, Kachiu C; Skotnicki-Grant, Sandy; Maibach, Howard

2016-06-01

To provide information from a literature review about the prevention, recognition, and treatment for contact dermatitis. This continuing education activity is intended for physicians and nurses with an interest in skin and wound care. After participating in this educational activity, the participant should be better able to:1. Identify signs and symptoms of and diagnostic measures for contact dermatitis.2. Identify causes and risks for contact dermatitis.3. Select appropriate treatment for contact dermatitis and its prevention. Contact dermatitis to wound care products is a common, often neglected problem. A review was conducted to identify articles relevant to contact dermatitis.A PubMed English-language literature review was conducted for appropriate articles published between January 2000 and December 2015.Contact dermatitis is both irritant (80% of cases) or allergic (20% of cases). Frequent use of potential contact allergens and impaired barrier function of the skin can lead to rising sensitization in patients with chronic wounds. Common known allergens to avoid in wound care patients include fragrances, colophony, lanolin, and topical antibiotics.Clinicians should be cognizant of the allergens in wound care products and the potential for sensitization. All medical devices, including wound dressings, adhesives, and bandages, should be labeled with their complete ingredients, and manufacturers should be encouraged to remove common allergens from wound care products, including topical creams, ointments, and dressings.

Metastable nanobubbles at the solid-liquid interface due to contact angle hysteresis.

PubMed

Nishiyama, Takashi; Yamada, Yutaka; Ikuta, Tatsuya; Takahashi, Koji; Takata, Yasuyuki

2015-01-27

Nanobubbles exist at solid-liquid interfaces between pure water and hydrophobic surfaces with very high stability, lasting in certain cases up to several days. Not only semispherical but also other shapes, such as micropancakes, are known to exist at such interfaces. However, doubt has been raised as to whether or not the nanobubbles are gas-phase entities. In this study, surface nanobubbles at a pure water-highly ordered pyrolytic graphite (HOPG) interface were investigated by peak force quantitative nanomechanics (PF-QNM). Multiple isolated nanobubbles generated by the solvent-exchange method were present on the terraced areas, avoiding the steps of the HOPG surface. Adjacent nanobubbles coalesced and formed metastable nanobubbles. Coalescence was enhanced by the PF-QNM measurement. We determined that nanobubbles can exist for a long time because of nanoscale contact angle hysteresis at the water-HOPG interface. Moreover, the hydrophilic steps of HOPG were avoided during coalescence, providing evidence that the nanobubbles are truly gas phase.

The DSM diagnostic criteria for sexual aversion disorder.

PubMed

Brotto, Lori A

2010-04-01

Sexual Aversion Disorder (SAD) is one of two Sexual Desire Disorders in the Diagnostic and Statistical Manual of Mental Disorders (DSM) and is defined as a "persistent or recurrent extreme aversion to, and avoidance of, all or almost all, genital sexual contact with a sexual partner" which causes distress or interpersonal difficulty. This paper reviews the short history of the diagnosis of SAD as well as the existing literature on its prevalence and etiology. Kaplan (1987) emphasized the phobic qualities of individuals with SAD who are highly avoidant of all forms of sexual contact. Much has also been written about the overlap between SAD and panic states, and the more obvious similarities between SAD and anxiety as opposed to sexual desire are described. There has been very little new published data on SAD since the publication of DSM-IV and the precise prevalence remains unknown. This paper critiques the placement of SAD as a Sexual Dysfunction and argues that it might more appropriately be placed within the Specific Phobia grouping as an Anxiety Disorder.

Poison ivy, oak, and sumac dermatitis identification, treatment, and prevention.

PubMed

Garner, L A

1999-05-01

Allergic contact dermatitis from poison ivy, oak, or sumac is common among people who work or exercise outdoors. The plants, classified in the genus Rhus or Toxicodendron, contain allergens that can cause reactions ranging from mild pruritus to severe urticaria or generalized maculopapular eruptions. Initial management includes cleansing, cold compresses, and, possibly, oral antihistamines for symptomatic relief. Topical corticosteroids are given for localized nonfacial eruptions; systemic corticosteroids are used for severe eruptions. Prevention involves avoiding contact with the plants and washing exposed skin within 2 hours.

Poison ivy dermatitis. Nuances in treatment.

PubMed

Williford, P M; Sheretz, E F

1994-02-01

Acute allergic contact dermatitis due to poison ivy or poison oak is a common presenting complaint in the practices of many primary care physicians. While the clinical features are well described, reported treatment regimens vary in both topical and systemic therapies. We review herein the variability of presenting morphologic features of the disease and common treatment regimens, with attention given to complications of therapy. We also comment on the correct botanical designation, incidence, and immune mechanisms of the disease state and review measures to avoid allergic contact dermatitis due to poison ivy and poison oak.

On the stability and instantaneous velocity of grasped frictionless objects

NASA Technical Reports Server (NTRS)

Trinkle, Jeffrey C.

1992-01-01

A quantitative test for form closure valid for any number of contact points is formulated as a linear program, the optimal objective value of which provides a measure of how far a grasp is from losing form closure. Another contribution of the study is the formulation of a linear program whose solution yields the same information as the classical approach. The benefit of the formulation is that explicit testing of all possible combinations of contact interactions can be avoided by the algorithm used to solve the linear program.

Image based weighted center of proximity versus directly measured knee contact location during simulated gait

PubMed Central

Wang, Hongsheng; Chen, Tony; Koff, Matthew F.; Hutchinson, Ian D.; Gilbert, Susannah; Choi, Dan; Warren, Russell F.; Rodeo, Scott A.; Maher, Suzanne A.

2014-01-01

To understand the mechanical consequences of knee injury requires a detailed analysis of the effect of that injury on joint contact mechanics during activities of daily living. Three-dimensional (3D) knee joint geometric models have been combined with knee joint kinematics to dynamically estimate the location of joint contact during physiological activities – using a weighted center of proximity (WCoP) method. However, the relationship between the estimated WCoP and the actual location of contact has not been defined. The objective of this study was to assess the relationship between knee joint contact location as estimated using the image-based WCoP method, and a directly measured weighted center of contact (WCoC) method during simulated walking. To achieve this goal, we created knee specific models of six human cadaveric knees from magnetic resonance imaging. All knees were then subjected to physiological loads on a knee simulator intended to mimic gait. Knee joint motion was captured using a motion capture system. Knee joint contact stresses were synchronously recorded using a thin electronic sensor throughout gait, and used to compute WCoC for the medial and lateral plateaus of each knee. WCoP was calculated by combining knee kinematics with the MRI-based knee specific model. Both metrics were compared throughout gait using linear regression. The anteroposterior (AP) location of WCoP was significantly correlated with that of WCoC on both tibial plateaus in all specimens (P < 0.01, 95% confidence interval of Person’s coefficient r > 0), but the correlation was not significant in the mediolateral (ML) direction for 4/6 knees (P > 0.05). Our study demonstrates that while the location of joint contact obtained from 3D knee joint contact model, using the WCoP method, is significantly correlated with the location of actual contact stresses in the AP direction, that relationship is less certain in the ML direction. PMID:24837219

Citation parameters of contact lens-related articles published in the ophthalmic literature.

PubMed

Cardona, Genís; Sanz, Joan P

2014-09-01

This study aimed at exploring the citation parameters of contact lenses articles published in the Ophthalmology thematic category of the Journal Citation Reports (JCR). The Thompson Reuters Web of Science database was accessed to record bibliometric information and citation parameters of all journals listed under the Ophthalmology area of the 2011 JCR edition, including the journals with main publication interests in the contact lens field. In addition, the same database was used to unveil all contact lens-related articles published in 2011 in the same thematic area, whereupon differences in citation parameters between those articles published in contact lens and non-contact lens-related journals were explored. Significant differences in some bibliometric indicators such as half-life and overall citation count were found between contact lens-related journals (shorter half-life and fewer citations) and the median values for the Ophthalmology thematic area of the JCR. Visual examination of all Ophthalmology journals uncovered a total of 156 contact lens-related articles, published in 28 different journals, with 27 articles each for Contact Lens & Anterior Eye, Eye & Contact Lens, and Optometry and Vision Science. Significant differences in citation parameters were encountered between those articles published in contact lens and non-contact lens source journals. These findings, which disclosed contact lenses to be a fertile area of research, may be of interest to researchers and institutions. Differences in bibliometric indicators are of relevance to avoid unwanted bias when conducting between- and within-discipline comparisons of articles, journals, and researchers.

Physical Therapist, Physical Therapist Assistant, and Student Response to Inappropriate Patient Sexual Behavior: Results of a National Survey.

PubMed

Cambier, Ziádee; Boissonnault, Jill S; Hetzel, Scott J; Plack, Margaret M

2018-06-08

A recent survey found that 84% of physical therapist, physical therapist assistant, and student respondents experienced inappropriate patient sexual behavior (IPSB) over their careers and 47% over the prior 12 months. Prevalence data justify consideration of how to address IPSB. The objective was to determine how physical therapist clinicians (used here to mean physical therapists, physical therapist assistants, and students) address IPSB and examine strategy impact. The design was observational and cross-sectional. Several sections of the American Physical Therapy Association and selected education programs fielded the electronic survey. Respondents reported on IPSB strategy frequency and effect. Response-strategy impact was tested for statistical significance. Open-ended comments were analyzed using qualitative methods. Of 1027 respondents, 396 had experienced IPSB over the prior 12 months; 391 provided data on the frequency and effect of response strategies used. Common informal responses included distraction, ignoring IPSB, and altering treatment to avoid physical contact or being alone. Common formal responses included reporting the behavior within the facility and documenting the behavior. Successful strategies included distraction, avoidance, direct confrontation, behavioral contracts, transfer of care, and chaperone use. Experienced clinicians were more likely to be direct, whereas novice clinicians were more likely to engage in unsuccessful actions of ignoring and joking. Limitations included self-report, clinician memory, and convenience sampling. The first findings in 20 years on physical therapist, physical therapist assistant, and student response to IPSB provide direction for the profession. Results indicate a need for clear workplace policies coupled with training for managers and supervisors to support clinicians in resolving IPSB. Policies on using behavioral contracts, chaperones, and transfer of care could empower staff to consider these successful options. Professional education and training for all physical therapy professionals on assertive communication and redirection strategies with IPSB appears warranted.

Behaviourally-inhibited temperament and female sex, two vulnerability factors for anxiety disorders, facilitate conditioned avoidance (also) in humans

PubMed Central

Sheynin, Jony; Beck, Kevin D.; Pang, Kevin C.H.; Servatius, Richard J.; Shikari, Saima; Ostovich, Jacqueline; Myers, Catherine E.

2014-01-01

Acquisition and maintenance of avoidance behaviour is a key feature of all human anxiety disorders. Animal models have been useful in understanding how anxiety vulnerability could translate into avoidance learning. For example, behaviourally-inhibited temperament and female sex, two vulnerability factors for clinical anxiety, are associated with faster acquisition of avoidance responses in rodents. However, to date, the translation of such empirical data to human populations has been limited since many features of animal avoidance paradigms are not typically captured in human research. Here, using a computer-based task that captures many features of rodent escape-avoidance learning paradigms, we investigated whether avoidance learning would be faster in humans with inhibited temperament and/or female sex and, if so, whether this facilitation would take the same form. Results showed that, as in rats, both vulnerability factors were associated with facilitated acquisition of avoidance behaviour in humans. Specifically, inhibited temperament was specifically associated with higher rate of avoidance responding, while female sex was associated with longer avoidance duration. These findings strengthen the direct link between animal avoidance work and human anxiety vulnerability, further motivating the study of animal models while also providing a simple testbed for a direct human testing. PMID:24412263

Food patch testing for irritable bowel syndrome.

PubMed

Stierstorfer, Michael B; Sha, Christopher T; Sasson, Marvin

2013-03-01

The traditional classification of irritable bowel syndrome (IBS) as a functional disorder has been challenged in recent years by evidence of ongoing low-grade gastrointestinal tract inflammation. Inflammation may alter gastrointestinal motility and thus be central to the pathogenesis of IBS. Many foods and food additives are known to cause allergic contact dermatitis. We hypothesize that allergenic foods and food additives may elicit a similar allergic reaction in the gastrointestinal tract, giving rise to symptoms suggestive of IBS. We sought to determine whether skin patch testing to a panel of foods and food additives may identify food allergens that may be responsible for symptoms of IBS. We performed skin patch testing to common allergenic foods and food additives on individuals with a history of or symptoms suggestive of IBS. We used patch test-guided avoidance diets to determine whether avoidance alleviates IBS symptoms. Thirty of the 51 study participants showed at least 1 doubtful or positive patch test result. Fourteen of the participants reported symptomatic improvement, ranging from slight to great, upon avoidance of the foods/food additives to which they reacted. Double-blind study design, inclusion of only patients with active IBS, larger sample size, more balanced gender distribution, testing of more foods/food additives, and longer duration of and more precise quantification of response to dietary avoidance are suggested for future studies. Allergic contact enteritis to ingested foods, food additives, or both may contribute to IBS symptoms. Patch testing may be useful in identifying the causative foods. Copyright © 2012 American Academy of Dermatology, Inc. Published by Mosby, Inc. All rights reserved.

Occupational contact dermatitis due to essential oils.

PubMed

Trattner, Akiva; David, Michael; Lazarov, Aneta

2008-05-01

Allergic contact dermatitis induced by the occupational use of products containing essential oils has not been studied comprehensively. The aim of the present report was to describe the characteristics, diagnosis, and outcome of 5 patients with occupational contact dermatitis because of essential oils attending our outpatient dermatology clinics over a 2-year period. These patients are added to the 11 cases reported thus far in the literature. The research shows that for proper diagnosis, patch tests with the standard series and the fragrance series should be performed, in addition to tests with the specific oils to which the patients were exposed. Patients should be instructed to avoid the allergens identified. Sensitization to essential oils has important implications for the occupational future of affected individuals.

Mentalizing eye contact with a face on a video: Gaze direction does not influence autonomic arousal.

PubMed

Lyyra, Pessi; Myllyneva, Aki; Hietanen, Jari K

2018-04-26

Recent research has revealed enhanced autonomic and subjective responses to eye contact only when perceiving another live person. However, these enhanced responses to eye contact are abolished if the viewer believes that the other person is not able to look back at the viewer. We purported to investigate whether this "genuine" eye contact effect can be reproduced with pre-recorded videos of stimulus persons. Autonomic responses, gaze behavior, and subjective self-assessments were measured while participants viewed pre-recorded video persons with direct or averted gaze, imagined that the video person was real, and mentalized that the person could see them or not. Pre-recorded videos did not evoke similar physiological or subjective eye contact effect as previously observed with live persons, not even when the participants were mentalizing being seen by the person. Gaze tracking results showed, however, increased attention allocation to faces with direct gaze compared to averted gaze directions. The results suggest that elicitation of the physiological arousal in response to genuine eye contact seems to require spontaneous experience of seeing and of being seen by another individual. © 2018 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

The ROSETTA PHILAE Lander damping mechanism as probe for the Comet soil strength.

NASA Astrophysics Data System (ADS)

Roll, R.

2015-10-01

The ROSETTA Lander is equipped with an one axis damping mechanism to dissipate kinetic energy during the touch down. This damping is necessary to avoid damages to the Lander by a hard landing shock and more important to avoid re-bouncing from ground with high velocity. The damping mechanism works best for perpendicular impact, which means the velocity vector is parallel to the damper axis and all three feet touch the ground at the same time. That is usually not the case. Part of the impact energy can be transferred into rotational energy at ground contact if the impact is not perpendicular. This energy will lift up the Lander from the ground if the harpoons and the hold down thruster fail, as happen in mission. The damping mechanism itself is an electrical generator, driven by a spindle inside a telescopic tube. This tube was extended in mission for landing by 200mm. A maximum damping length of 140mm would be usually required to compensate a landing velocity of 1m/s, if the impact happens perpendicular on hard ground. After landing the potentiometer of the telescopic tube reading shows a total damping length of only 42,5mm. The damping mechanism and the overall mechanical behavior of the Lander at touch down are well tested and characterized and transferred to a multi-body computer model. The incoming and outgoing flightpath of PHILAE allow via computer-simulation the reconstruction of the touch down. It turns out, that the outgoing flight direction is dominated by the local ground slope and that the damping length is strongly dependent on the soil strength. Damping of soft comet ground must be included to fit the damping length measured. Scenario variations of the various feet contact with different local surface features (stone or regolith) and of different soil models finally lead to a restricted range for the soil strength at the touch down area.

Optimized programming algorithm for cylindrical and directional deep brain stimulation electrodes.

PubMed

Anderson, Daria Nesterovich; Osting, Braxton; Vorwerk, Johannes; Dorval, Alan D; Butson, Christopher R

2018-04-01

Deep brain stimulation (DBS) is a growing treatment option for movement and psychiatric disorders. As DBS technology moves toward directional leads with increased numbers of smaller electrode contacts, trial-and-error methods of manual DBS programming are becoming too time-consuming for clinical feasibility. We propose an algorithm to automate DBS programming in near real-time for a wide range of DBS lead designs. Magnetic resonance imaging and diffusion tensor imaging are used to build finite element models that include anisotropic conductivity. The algorithm maximizes activation of target tissue and utilizes the Hessian matrix of the electric potential to approximate activation of neurons in all directions. We demonstrate our algorithm's ability in an example programming case that targets the subthalamic nucleus (STN) for the treatment of Parkinson's disease for three lead designs: the Medtronic 3389 (four cylindrical contacts), the direct STNAcute (two cylindrical contacts, six directional contacts), and the Medtronic-Sapiens lead (40 directional contacts). The optimization algorithm returns patient-specific contact configurations in near real-time-less than 10 s for even the most complex leads. When the lead was placed centrally in the target STN, the directional leads were able to activate over 50% of the region, whereas the Medtronic 3389 could activate only 40%. When the lead was placed 2 mm lateral to the target, the directional leads performed as well as they did in the central position, but the Medtronic 3389 activated only 2.9% of the STN. This DBS programming algorithm can be applied to cylindrical electrodes as well as novel directional leads that are too complex with modern technology to be manually programmed. This algorithm may reduce clinical programming time and encourage the use of directional leads, since they activate a larger volume of the target area than cylindrical electrodes in central and off-target lead placements.

Slip-mediated dewetting of polymer microdroplets

PubMed Central

McGraw, Joshua D.; Chan, Tak Shing; Maurer, Simon; Salez, Thomas; Benzaquen, Michael; Raphaël, Elie; Brinkmann, Martin; Jacobs, Karin

2016-01-01

Classical hydrodynamic models predict that infinite work is required to move a three-phase contact line, defined here as the line where a liquid/vapor interface intersects a solid surface. Assuming a slip boundary condition, in which the liquid slides against the solid, such an unphysical prediction is avoided. In this article, we present the results of experiments in which a contact line moves and where slip is a dominating and controllable factor. Spherical cap-shaped polystyrene microdroplets, with nonequilibrium contact angle, are placed on solid self-assembled monolayer coatings from which they dewet. The relaxation is monitored using in situ atomic force microscopy. We find that slip has a strong influence on the droplet evolutions, both on the transient nonspherical shapes and contact line dynamics. The observations are in agreement with scaling analysis and boundary element numerical integration of the governing Stokes equations, including a Navier slip boundary condition. PMID:26787903

Study of the influence of the cutting temperature on the magnitude of the contact forces in the machining fixtures

NASA Astrophysics Data System (ADS)

Cioată, V. G.; Kiss, I.; Alexa, V.; Raţiu, S. A.; Racov, M.

2018-01-01

In the machining process, the workpieces are installed in machining fixtures in order to establish a strictly determined position with the cutting tool or its trajectory. During the cutting process, the weight of the workpiece, the forces and moments of inertia, cutting forces and moments, clamping forces, the heat released during the cutting process determine the contact forces between the locators and the workpiece. The magnitude of these forces is important because too large value can destroy the surface of the workpiece, and a too small value can cause the workpiece to slip on the locators or even the loss of the contact with the workpiece. Both situations must be avoided. The paper presents a study, realized with CAE software, regarding the influence of the cutting temperature on the magnitude of the contact forces in a machining fixture for the milling a rectangular workpiece.

On multiscale moving contact line theory.

PubMed

Li, Shaofan; Fan, Houfu

2015-07-08

In this paper, a multiscale moving contact line (MMCL) theory is presented and employed to simulate liquid droplet spreading and capillary motion. The proposed MMCL theory combines a coarse-grained adhesive contact model with a fluid interface membrane theory, so that it can couple molecular scale adhesive interaction and surface tension with hydrodynamics of microscale flow. By doing so, the intermolecular force, the van der Waals or double layer force, separates and levitates the liquid droplet from the supporting solid substrate, which avoids the shear stress singularity caused by the no-slip condition in conventional hydrodynamics theory of moving contact line. Thus, the MMCL allows the difference of the surface energies and surface stresses to drive droplet spreading naturally. To validate the proposed MMCL theory, we have employed it to simulate droplet spreading over various elastic substrates. The numerical simulation results obtained by using MMCL are in good agreement with the molecular dynamics results reported in the literature.

The evaluation of shear deformation for contact analysis with large displacement

NASA Astrophysics Data System (ADS)

Nizam, Z. M.; Obiya, H.; Ijima, K.; Azhar, A. T. S.; Hazreek, Z. A. M.; Shaylinda, M. Z. N.

2018-04-01

A common problem encountered in the study of contact problem is the failure to obtain stable and accurate convergence result when the contact node is close to the element edge, which is referred as “critical area”. In previous studies, the modification of the element force equation to apply it to a node-element contact problem using the Euler-Bernoulli beam theory [1]. A simple single-element consists two edges and a contact point was used to simulate contact phenomenon of a plane frame. The modification was proven to be effective by the converge-ability of the unbalanced force at the tip of element edge, which enabled the contact node to “pass-through”, resulting in precise results. However, in another recent study, we discover that, if shear deformation based on Timoshenko beam theory is taken into consideration, a basic simply supported beam coordinate afforded a much simpler and more efficient technique for avoiding the divergence of the unbalanced force in the “critical area”. Using our unique and robust Tangent Stiffness Method, the improved equation can be used to overcome any geometrically nonlinear analyses, including those involving extremely large displacements.

Fitting an MSD (mini scleral design) rigid contact lens in advanced keratoconus with INTACS.

PubMed

Dalton, Kristine; Sorbara, Luigina

2011-12-01

Keratoconus is a bilateral degenerative disease characterized by a non-inflammatory, progressive central corneal ectasia (typically asymmetric) and decreased vision. In its early stages it may be managed with spectacles and soft contact lenses but more commonly it is managed with rigid contact lenses. In advanced stages, when contact lenses can no longer be fit, have become intolerable, or corneal damage is severe, a penetrating keratoplasty is commonly performed. Alternative surgical techniques, such as the use of intra-stromal corneal ring segments (INTACS) have been developed to try and improve the fit of rigid contact lenses in keratoconic patients and avoid penetrating keratoplasties. This case report follows through the fitting of rigid contact lenses in an advanced keratoconic cornea after an INTACS procedure and discusses clinical findings, treatment options, and the use of mini-scleral and scleral lens designs as they relate to the challenges encountered in managing such a patient. Mini-scleral and scleral lenses are relatively easy to fit, and can be of benefit to many patients, including advanced keratoconic patients, post-INTAC patients and post-penetrating keratoplasty patients. 2011 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.

Field-gradient partitioning for fracture and frictional contact in the material point method: Field-gradient partitioning for fracture and frictional contact in the material point method [Fracture and frictional contact in material point method using damage-field gradients for velocity-field partitioning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Homel, Michael A.; Herbold, Eric B.

Contact and fracture in the material point method require grid-scale enrichment or partitioning of material into distinct velocity fields to allow for displacement or velocity discontinuities at a material interface. We present a new method which a kernel-based damage field is constructed from the particle data. The gradient of this field is used to dynamically repartition the material into contact pairs at each node. Our approach avoids the need to construct and evolve explicit cracks or contact surfaces and is therefore well suited to problems involving complex 3-D fracture with crack branching and coalescence. A straightforward extension of this approachmore » permits frictional ‘self-contact’ between surfaces that are initially part of a single velocity field, enabling more accurate simulation of granular flow, porous compaction, fragmentation, and comminution of brittle materials. Finally, numerical simulations of self contact and dynamic crack propagation are presented to demonstrate the accuracy of the approach.« less

Skin-specific training experience of workers assessed for contact dermatitis.

PubMed

Zack, B; Arrandale, V; Holness, D L

2018-05-17

Contact dermatitis is a common and preventable work-related disease. Skin-specific training may be effective for preventing occupational contact dermatitis, but little information is available regarding actual workplace training and its effectiveness. To describe workplace skin-specific training among workers with suspected contact dermatitis. Patch test patients being assessed for suspected contact dermatitis at an occupational health clinic in Toronto, Canada, completed a questionnaire on training experiences, workplace characteristics, exposures and skin protection practices. Of 175 patients approached, 122 (71%) workers completed questionnaires. Many (80%) had received general occupational health and safety and hazardous materials training (76%). Fewer (39%) received skin-specific training. Of those with work-related contact dermatitis, 52% did not receive skin-specific training. Skin-specific training was commonly provided by health and safety professionals or supervisors using video, classroom and online techniques. Content included glove use, exposure avoidance and hand washing information. Workers that received skin-specific training found it memorable (87%), useful (85%) and common sense in nature (100%). This study indicates gaps in workplace training on skin disease prevention for workers with contact dermatitis. Workers perceived skin-specific training to be useful. Understanding worker training experiences is important to prevention programme development and reducing work-related skin disease.

Field-gradient partitioning for fracture and frictional contact in the material point method: Field-gradient partitioning for fracture and frictional contact in the material point method [Fracture and frictional contact in material point method using damage-field gradients for velocity-field partitioning

DOE PAGES

Homel, Michael A.; Herbold, Eric B.

2016-08-15

Contact and fracture in the material point method require grid-scale enrichment or partitioning of material into distinct velocity fields to allow for displacement or velocity discontinuities at a material interface. We present a new method which a kernel-based damage field is constructed from the particle data. The gradient of this field is used to dynamically repartition the material into contact pairs at each node. Our approach avoids the need to construct and evolve explicit cracks or contact surfaces and is therefore well suited to problems involving complex 3-D fracture with crack branching and coalescence. A straightforward extension of this approachmore » permits frictional ‘self-contact’ between surfaces that are initially part of a single velocity field, enabling more accurate simulation of granular flow, porous compaction, fragmentation, and comminution of brittle materials. Finally, numerical simulations of self contact and dynamic crack propagation are presented to demonstrate the accuracy of the approach.« less

25 CFR 20.200 - What contact will the Bureau maintain with State, tribal, county, local, and other Federal agency...

Code of Federal Regulations, 2010 CFR

2010-04-01

..., DEPARTMENT OF THE INTERIOR HUMAN SERVICES FINANCIAL ASSISTANCE AND SOCIAL SERVICES PROGRAMS Welfare Reform... agency programs? We will coordinate all financial assistance and social services programs with state... social services program avoids duplication of assistance. ...

25 CFR 20.200 - What contact will the Bureau maintain with State, tribal, county, local, and other Federal agency...

Code of Federal Regulations, 2011 CFR

2011-04-01

..., DEPARTMENT OF THE INTERIOR HUMAN SERVICES FINANCIAL ASSISTANCE AND SOCIAL SERVICES PROGRAMS Welfare Reform... agency programs? We will coordinate all financial assistance and social services programs with state... social services program avoids duplication of assistance. ...

25 CFR 20.200 - What contact will the Bureau maintain with State, tribal, county, local, and other Federal agency...

Code of Federal Regulations, 2013 CFR

2013-04-01

..., DEPARTMENT OF THE INTERIOR HUMAN SERVICES FINANCIAL ASSISTANCE AND SOCIAL SERVICES PROGRAMS Welfare Reform... agency programs? We will coordinate all financial assistance and social services programs with state... social services program avoids duplication of assistance. ...

25 CFR 20.200 - What contact will the Bureau maintain with State, tribal, county, local, and other Federal agency...

Code of Federal Regulations, 2012 CFR

2012-04-01

..., DEPARTMENT OF THE INTERIOR HUMAN SERVICES FINANCIAL ASSISTANCE AND SOCIAL SERVICES PROGRAMS Welfare Reform... agency programs? We will coordinate all financial assistance and social services programs with state... social services program avoids duplication of assistance. ...

25 CFR 20.200 - What contact will the Bureau maintain with State, tribal, county, local, and other Federal agency...

Code of Federal Regulations, 2014 CFR

2014-04-01

..., DEPARTMENT OF THE INTERIOR HUMAN SERVICES FINANCIAL ASSISTANCE AND SOCIAL SERVICES PROGRAMS Welfare Reform... agency programs? We will coordinate all financial assistance and social services programs with state... social services program avoids duplication of assistance. ...

21 CFR 333.350 - Labeling of acne drug products.

Code of Federal Regulations, 2011 CFR

2011-04-01

... following: “Clears,” “Clears up,” “Clears up most,” “Dries,” “Dries up,” “Dries and clears,” “Helps clear...] avoid contact with hair and dyed fabrics, which may be bleached by this product [bullet] skin irritation...

Shaping Approach Responses as Intervention for Specific Phobia in a Child with Autism

ERIC Educational Resources Information Center

Ricciardi, Joseph N.; Luiselli, James K.; Camare, Marianne

2006-01-01

We evaluated contact desensitization (reinforcing approach responses) as intervention for specific phobia with a child diagnosed with autism. During hospital-based intervention, the boy was able to encounter previously avoided stimuli. Parental report suggested that results were maintained postdischarge. (Contains 1 figure.)

Chapter 13. Physiology and ecology of host defense against microbial invaders

USDA-ARS?s Scientific Manuscript database

Insects mount a complex hierarchy of defenses that pathogens must overcome before successful infection is achieved. Behavioral avoidance and antiseptic behaviors by host insects reduce the degree of encounters between the insect and pathogens. Any pathogen that contacts or establishes on a potentia...

Non-Dissipative Structural Evolutions in Granular Materials

NASA Astrophysics Data System (ADS)

Pouragha, Mehdi; Wan, Richard

2017-06-01

The structure of the contact network in granular assemblies can evolve due to either dissipative mechanisms such as sliding at contact points, or non-dissipative mechanisms through the phenomenon of contact gain and loss. Being associated with negligible deformations, non-dissipative mechanisms is actually active even in the small strain range of 10-3, especially in the case of densely packed assemblies. Hence, from a constitutive modelling point of view, it is crucial to be able to estimate such non-dissipative evolutions since both elastic and plastic properties of granular assemblies highly depend on contact network characteristics. The current study proposes an analytical scheme that allows us to estimate the non-dissipative contact gain/loss regime in terms of directional changes in the average contact force. The probability distribution of contact forces is used to compute the number of lost contact for each direction. Similarly, the number of newly formed contacts is estimated by considering the probability distribution of the gap between neighbouring particles. Based on the directional contact gain/loss computed, the changes in coordination number and fabric anisotropy can be found which, together with statistical treatments of Love-Weber stress expression, form a complete system of equations describing the evolution of other controlling microvariables. Finally, the results of the calculations have been compared with DEM simulations which verify the accuracy of the proposed scheme.

The combined diagnosis of allergic and irritant contact dermatitis in a retrospective cohort of 1000 consecutive patients with occupational contact dermatitis.

PubMed

Schwensen, Jakob F; Menné, Torkil; Johansen, Jeanne D

2014-12-01

The diagnosis of combined allergic and irritant contact dermatitis is an accepted subdiagnosis for hand dermatitis, and it is often considered in a patient with contact dermatitis, a positive and relevant patch test result, and wet work exposure. We therefore hypothesize that it is arbitrary for wet work exposure to be taken into consideration in a patient with newly diagnosed relevant contact allergy. Furthermore, an overestimation of the diagnosis will probably occur if the criteria for wet work exposure are applied correctly, as many occupations have an element of wet work. To find the statistically expected number of combined allergic and irritant contact dermatitis cases in 1000 patients, and to evaluate the diagnostic criteria for the diagnosis. One thousand consecutive patients with occupational contact dermatitis from a hospital unit in Denmark were assessed. The expected number of cases with the diagnosis of combined allergic and irritant contact dermatitis was 0.33%, as compared with the observed number of 6.4%. Females occupied in wet occupations were often diagnosed with combined allergic and irritant contact dermatitis (p < 0.005). The diagnosis of combined allergic and irritant contact dermatitis should be used critically to avoid misclassification, and possible criteria for the diagnosis are proposed. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

T cell lymphomatoid contact dermatitis: a challenging case and review of the literature.

PubMed

Knackstedt, Thomas J; Zug, Kathryn A

2015-02-01

Lymphomatoid contact dermatitis is a pseudolymphoma with clinical and histological features of allergic contact dermatitis and cutaneous T cell lymphoma. Incorrect diagnosis may lead to unnecessary testing, unnecessary treatment, or patient harm. The objective of this study is to present a case to demonstrate the diagnostic challenge and overlap between allergic contact dermatitis and cutaneous T cell lymphoma in a patient with lymphomatoid contact dermatitis caused by methylchoroisothiazolinone/methylisothiazolinone and paraben mix, and to review the existing literature in order to summarize the demographics, clinical features, allergens and treatments reported for lymphomatoid contact dermatitis. A search of major scientific databases was conducted for English-language articles reporting cases of lymphomatoid contact dermatitis or additional synonymous search headings. Nineteen articles with a total of 23 patients were analysed. Lymphomatoid contact dermatitis was more common in men, with an average age of 58.5 years. Fourteen unique allergens were identified and confirmed by patch testing. However, no single test or study was diagnostic of lymphomatoid contact dermatitis. Allergen avoidance was the most useful management tool, but selected patients required topical or systemic immunosuppression. In conclusion, without specific diagnostic features, evaluation for lymphomatoid contact dermatitis should include a thorough history and examination, patch testing, and biopsy with immunohistochemistry and clonality studies. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

[Chronic fatigue and strategies of coping with occupational stress in police officers].

PubMed

Stepka, Ewa; Basińska, Małgorzata Anna

2014-01-01

Work as one of the most important activities in human life is related to stressful and difficult situations. Police officers make one of the many occupational groups that are particularly threatened by contact with a number of stressors. Therefore, their strategies of coping with stress are particularly important, because they play an important role in their functioning at work. The nature of the service as well as shift work and psychological costs incurred by police officers contribute to the emergence of chronic fatigue. The aim of this study was to evaluate the level of chronic fatigue in police officers and its relationship with the strategies of coping with occupational stress. A group of 61 police officers was examined. The following research methods were used: 1) Latack Coping Scale examining stress coping strategies at work (positive thinking, direct action, avoidance/resignation, seeking help, alcohol or stimulants use); 2) Mood Assessment Questionnaire CIS-20R examining the level of chronic fatigue and its components (subjective feeling of fatigue, impaired attention and concentration, reduced motivation, reduced activity); 3) Personal questionnaire providing socio-demographic data. It was found that the level of chronic fatigue in the group of the examined police officers was high (sten 8th). The most often used strategies of coping with stress were direct action and positive thinking, and the least often used strategy was the use of alcohol and stimulants. A significant negative correlation between the general level of chronic fatigue and the avoidance/resignation strategy was found. The results indicate that chronic fatigue is a problem affecting police officers and it is related to the stress coping strategies used.

[New trends in tonometry].

PubMed

Draeger, J A; Schwenteck, T; Ruokonen, P C

2006-10-01

Though the knowledge about the risk of elevated intraocular pressure for pathogenesis for development and progress of glaucoma is more than 400 years old. It took another 300 years before by means of tonometry this elevation could be quantified. After discussion of the key words it is our aim to demonstrate the latest trends in tonometry, specifically by use of modern electronics for instrument design. Goldmann was the founder of the "applanation tonometry", measuring the corelation of applanated area and applied force. Here, the next step was the development of instruments, measuring independent of position or gravity to allow application also at the lying patient. Electronic area detection was the next step to avoid examinor's error. Also important was the introduction of automatic UV-desinfection to avoid contamination of the other eye or other patients. Other tonometers control the force applied by an inductive method, which also allows application independent of position. Airpuff-tonometry uses completely different measuring principles - the resulting change of corneal curvature indicates the intraocular pressure. The impedance principle is applied even through the closed eye lid. The shock waves resulting shall be measured. Direct application of a surface sensor incorporated into a concave surface contact body shall allow direct measurement of intraocular pressure independent of corneal thickness, curvature, astigmatism. This method has been tried for more than 20 years. Also exposition of the eye to count waves of different frequency was an early attempt. Here also change of reflectivity is used to calculate intraocular pressure. Even after use of modern electronic technology the precision of many of these new devices does not lead to better results. This specifically is shown by modern calibration methods.

In vivo anatomical analysis of arterial contact with trigeminal nerve: detection with three-dimensional spoiled grass imaging.

PubMed

Ueda, F; Suzuki, M; Fujinaga, Y; Kadoya, M; Takashima, T

1999-09-01

The purpose of this study was to review the normal in vivo neurovascular relationship between the trigeminal nerve and surrounding arteries without the use of volunteers. 290 nerves in 145 cases were reviewed during a 1-year period. Axial source images and multiplanar reconstructed (MPR) images were used to determine the neurovascular contact and direction of contact. Multiplanar volume reformation (MPVR) was used to identify the contact vessels and to demonstrate the relationship between the nerve and arteries. Vascular contact was found in 29% of the 290 nerves (83 nerves). The arteries involved were the superior cerebellar artery (SCA) or the anterior inferior cerebellar artery (AICA). Vascular contact with two arteries was found in 3%. Of the 286 asymptomatic nerves, the nerve was located between the two vessels in 3% and compression was seen in 1%. Three points of vascular contact by the two arteries were identified in one asymptomatic nerve. The direction of contact between the SCA and the nerve was superior (38%), superomedial (32%) or medial (15%) in most cases. The direction of contact between the AICA and the nerve was inferior, inferolateral or lateral in all cases. Vascular contact at the root entry zone (REZ) was noted in 90%. Four nerves were affected by trigeminal neuralgia, one of which touched an artery and two were compressed. It was concluded that arterial contact can be assessed without difficulty but evaluation of vascular compression is not easy.

Evolution of precopulatory and post-copulatory strategies of inbreeding avoidance and associated polyandry.

PubMed

Duthie, A B; Bocedi, G; Germain, R R; Reid, J M

2018-01-01

Inbreeding depression is widely hypothesized to drive adaptive evolution of precopulatory and post-copulatory mechanisms of inbreeding avoidance, which in turn are hypothesized to affect evolution of polyandry (i.e. female multiple mating). However, surprisingly little theory or modelling critically examines selection for precopulatory or post-copulatory inbreeding avoidance, or both strategies, given evolutionary constraints and direct costs, or examines how evolution of inbreeding avoidance strategies might feed back to affect evolution of polyandry. Selection for post-copulatory inbreeding avoidance, but not for precopulatory inbreeding avoidance, requires polyandry, whereas interactions between precopulatory and post-copulatory inbreeding avoidance might cause functional redundancy (i.e. 'degeneracy') potentially generating complex evolutionary dynamics among inbreeding strategies and polyandry. We used individual-based modelling to quantify evolution of interacting precopulatory and post-copulatory inbreeding avoidance and associated polyandry given strong inbreeding depression and different evolutionary constraints and direct costs. We found that evolution of post-copulatory inbreeding avoidance increased selection for initially rare polyandry and that evolution of a costly inbreeding avoidance strategy became negligible over time given a lower-cost alternative strategy. Further, fixed precopulatory inbreeding avoidance often completely precluded evolution of polyandry and hence post-copulatory inbreeding avoidance, but fixed post-copulatory inbreeding avoidance did not preclude evolution of precopulatory inbreeding avoidance. Evolution of inbreeding avoidance phenotypes and associated polyandry is therefore affected by evolutionary feedbacks and degeneracy. All else being equal, evolution of precopulatory inbreeding avoidance and resulting low polyandry is more likely when post-copulatory inbreeding avoidance is precluded or costly, and evolution of post-copulatory inbreeding avoidance greatly facilitates evolution of costly polyandry. © The Authors. Journal of Evolutionary Biology published by John Wiley & Sons Ltd on behalf of European Society for Evolutionary Biology.

Lack of behavioural evidence for kin avoidance in mate choice in a hymenopteran parasitoid (Hymenoptera: Braconidae).

PubMed

Bourdais, D; Hance, T

2009-05-01

Mechanisms for inbreeding avoidance should be prevalent in insects that reproduce by arrhenotokous haplodiploidy because of the higher potential production of unviable diploid males in inbred matings. Few studies have focused on mating strategies in insect parasitoids and even less on kinship relationships during mate choice. In this study we tested avoidance of kin as mate in the parasitic wasp Aphidius matricariae (Hymenoptera: Braconidae) using an ethological approach. Key mating parameters, such as male wing fanning, latent period before genitalia contact and duration of copulation were measured. No evidence for kin avoidance in mate choice in both A. matricariae males and females was observed in our behaviour (no choice or choice tests) tests. This lack of ethological sib mating avoidance could be due to different factors such as sex determination rule different than the single locus complementary sex determination, making lower the proportion of diploid males in case of sib matings and thus its negative consequence. The existence of other inbreeding avoidance strategies and mechanisms that reduce the probability of 2 receptive relatives meeting in nature may be common, for example, inbred mating may be rare through differential dispersal, delayed maturation, or protandry.

Indentation Schmid factor and orientation dependence of nanoindentation pop-in behavior of NiAl single crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Tianlei; Gao, Yanfei; Bei, Hongbin

2011-01-01

Instrumented nanoindentation techniques have been widely used to characterize the small-scale mechanical behavior of materials. The elastic-plastic transition during nanoindentation is often indicated by a sudden displacement burst (pop-in) in the measured load-displacement curve. In defect-free single crystals, the pop-in is believed to be the result of homogeneous dislocation nucleation because the maximum shear stress corresponding to the pop-in load approaches the theoretical strength of the materials and because the statistical distribution of pop-in stresses is consistent with what is expected for a thermally activated process of homogeneous dislocation nucleation. This paper investigates whether this process is affected by crystallographymore » and stress components other than the resolved shear stress. A Stroh formalism coupled with the two-dimensional Fourier transformation is used to derive the analytical stress fields in elastically anisotropic solids under Hertzian contact, which allows the determination of an indentation Schmid factor, namely, the ratio of maximum resolved shear stress to the maximum contact pressure. Nanoindentation tests were conducted on B2-structured NiAl single crystals with different surface normal directions. This material was chosen because it deforms at room temperature by {110}<001> slip and thus avoids the complexity of partial dislocation nucleation. Good agreement is obtained between the experimental data and the theoretically predicted orientation dependence of pop-in loads based on the indentation Schmid factor. Pop-in load is lowest for indentation directions close to <111> and highest for those close to <001>. In nanoindentation, since the stress component normal to the slip plane is typically comparable in magnitude to the resolved shear stress, we find that the pressure sensitivity of homogeneous dislocation nucleation cannot be determined from pop-in tests. Our statistical measurements generally confirm the thermal activation model of homogeneous dislocation nucleation. That is, the extracted dependence of activation energy on resolved shear stress is almost the same for all the indentation directions considered in this study, except for those close to <001>. Because very high pop-in loads are measured for orientations close to <001>, which implies a large contact area at pop-in, there is a higher probability of activating pre-existing dislocations in these orientations, which may explain the discrepancy near <001>.« less

Sonographically guided deep plantar fascia injections: where does the injectate go?

PubMed

Maida, Eugene; Presley, James C; Murthy, Naveen; Pawlina, Wojciech; Smith, Jay

2013-08-01

To determine the distribution of sonographically guided deep plantar fascia injections in an unembalmed cadaveric model. A single experienced operator completed 10 sonographically guided deep plantar fascia injections in 10 unembalmed cadaveric specimens (5 right and 5 left) obtained from 6 donors (2 male and 4 female) aged 49 to 95 years (mean, 77.5 years) with a mean body mass index of 23.2 kg/m(2) (range, 18.4-26.3 kg/m(2)). A 12-3-MHz linear array transducer was used to direct a 22-gauge, 38-mm stainless steel needle deep to the plantar fascia at the anterior aspect of the calcaneus using an in-plane, medial-to-lateral approach. In each case, 1.5 mL of 50% diluted colored latex was injected deep to the plantar fascia. After a minimum of 72 hours, study coinvestigators dissected each specimen to assess injectate placement. All 10 injections accurately placed latex adjacent to the deep side of the plantar fascia at the anterior calcaneus. However, the flexor digitorum brevis (FDB) origin from the plantar fascia variably limited direct latex contact with the plantar fascia, and small amounts of latex interdigitated with the FDB origin in 90% (9 of 10). In all 10 specimens, latex also covered the traversing first branch of the lateral plantar nerve (FBLPN, ie, Baxter nerve) between the FDB and quadratus plantae muscles. No latex was found in the plantar fat pad or plantar fascia in any specimen. Sonographically guided deep plantar fascia injections reliably deliver latex deep to the plantar fascia while avoiding intrafascial injection. However, the extent of direct plantar fascia contact is variable due to the intervening FDB. On the contrary, the traversing FBLPN is reliably covered by the injection. Deep plantar fascia injections may have a role in the management of refractory plantar fasciitis, particularly following failed superficial perifascial or intrafascial injections, in cases of preferential deep plantar fascia involvement, or when entrapment/irritation of the distal FBLPN is suspected.

Microbial contamination of syringes during preparation: the direct influence of environmental cleanliness and risk manipulations on end-product quality.

PubMed

Stucki, Cyril; Sautter, Anna-Maria; Favet, Jocelyne; Bonnabry, Pascal

2009-11-15

The direct influence of environmental cleanliness and risk manipulations on prepared syringes was evaluated. Media-fill testing was used to estimate potential microbial contamination. Syringes were prepared in three different environments using four different uncontrolled high-risk manipulations. The three environments included an International Organization for Standardization (ISO) class 5 horizontal laminar-airflow hood in an ISO class 6 cleanroom (in accordance with United States Pharmacopeia [USP] chapter 797), an ISO class 7 drug preparation area of an operating room, and an uncontrolled decentralized pharmacy in a ward. For each combination of environment and manipulation, 100 syringes were filled by a single operator. The four high-risk manipulations used included simple filling of syringes with trypticase soy broth, three-second contact by the ungloved fingers of the operator with the hub of the syringe, three-second contact between an object and the hub of the syringe, and exposure of the filled syringes to ambient air for 10 minutes. Of the 1500 syringes prepared in three different environments, none produced within the cleanroom contained microorganisms, 6% were contaminated in the operating room, and 16% were contaminated in the ward (p < 0.0001). Certain high-risk manipulations were associated with a significant increase in the contamination of the surrogate syringes, including exposure to nonsterile ambient air and nonsterile objects or fingers (p < 0.0001). High contamination rates were measured when the hub of syringes touched nonsterile environmental surfaces and fingers, whereas the drawn-air manipulation was associated with a lower risk of contamination. Working within a properly operating unidirectional airflow primary engineering control in an ISO class 5 cleanroom in accordance with USP chapter 797 requirements was demonstrated to be the best way to avoid bacterial or fungal contamination of injectable drugs directly resulting in patient infections.

Shoe contact dermatitis from dimethyl fumarate: clinical manifestations, patch test results, chemical analysis, and source of exposure.

PubMed

Giménez-Arnau, Ana; Silvestre, Juan Francisco; Mercader, Pedro; De la Cuadra, Jesus; Ballester, Isabel; Gallardo, Fernando; Pujol, Ramón M; Zimerson, Erik; Bruze, Magnus

2009-11-01

The methyl ester form of fumaric acid named dimethyl fumarate (DMF) is an effective mould-growth inhibitor. Its irritating and sensitizing properties were demonstrated in animal models. Recently, DMF has been identified as responsible for furniture contact dermatitis in Europe. To describe the clinical manifestations, patch test results, shoe chemical analysis, and source of exposure to DMF-induced shoe contact dermatitis. Patients with suspected shoe contact dermatitis were studied in compliance with the Declaration of Helsinki. Patch test results obtained with their own shoe and the European baseline series, acrylates and fumaric acid esters (FAE), were recorded according to international guidelines. The content of DMF in shoes was analysed with gas chromatography and mass spectrometry. Acute, immediate irritant contact dermatitis and non-immunological contact urticaria were observed in eight adults and two children, respectively. All the adult patients studied developed a delayed sensitization demonstrated by a positive patch testing to DMF < or = 0.1% in pet. Cross-reactivity with other FAEs and acrylates was observed. At least 12 different shoe brands were investigated. The chemical analysis from the available shoes showed the presence of DMF. DMF in shoes was responsible for severe contact dermatitis. Global preventive measures for avoiding contact with DMF are necessary.

Piezoviscosity In Lubrication Of Nonconformal Contacts

NASA Technical Reports Server (NTRS)

Jeng, Yeau-Ren; Hamrock, Bernard J.; Brewe, David E.

1988-01-01

Developments in theory of lubrication. Analysis of piezoviscous-rigid regime of lubrication of two ellipsoidal contacts. Begins with Reynolds equation for point contact. Equation nondimensionalized using Roelands empirical formula and Dowson and Higginson formula. Equation solved numerically. Solutions obtained for full spectrum of conditions to find effects of dimensionless load, speed, parameters of lubricated and lubricating materials, and angle between direction of rolling and direction of entrainment of lubricant.

PDGF-A suppresses contact inhibition during directional collective cell migration.

PubMed

Nagel, Martina; Winklbauer, Rudolf

2018-06-08

The leading edge mesendoderm (LEM) of the Xenopus gastrula moves as an aggregate by collective migration. However, LEM cells on fibronectin in vitro show contact inhibition of locomotion by quickly retracting lamellipodia upon mutual contact. We found that a fibronectin-integrin-syndecan module acts between p21-activated kinase-1 upstream and ephrinB1 downstream to promote the contact-induced collapse of lamellipodia. To function in this module, fibronectin has to be present as puncta on the surface of LEM cells. To overcome contact inhibition in LEM cell aggregates, PDGF-A deposited in the endogenous substratum of LEM migration blocks the fibronectin-integrin-syndecan module at the integrin level. This stabilizes lamellipodia preferentially in the direction of normal LEM movement and supports cell orientation and the directional migration of the coherent LEM cell mass. © 2018. Published by The Company of Biologists Ltd.

A closed system for islet isolation and purification using the COBE2991 cell processor may reduce the need of clean room facilities.

PubMed

Klaffschenkel, R A; Biesemeier, A; Waidmann, M; Northoff, H; Steurer, W; Königsrainer, A; Lembert, N

2007-01-01

During the isolation of human islets of Langerhans the digest has repeated direct contact with the ambient atmosphere. In order to fulfill GMP requirements in clinical applications, the entire cell preparation must be performed in clean room facilities. We hypothesized that the use of a closed system, which avoids the direct exposure of tissue to the atmosphere, would significantly ease the preparation procedure. To avoid the direct atmosphere exposure we tested a modification of the isolation and purification process by performing all islet preparation steps in a closed system. In this study we compared the isolation outcome of the traditional open preparation technique with the new closed system. Pancreata from 6-month-old hybrid pigs were procured in the local slaughterhouse. After digestion/filtration the digest was cooled, collected, and concentrated in centrifugation containers and purified thereafter in the COBE2991 by top loading (control). In the control group 502 +/- 253 IEQ per gram pancreas were purified. The total preparation time amounted to 12 h. In the closed system the digest was cooled and directly pumped into the COBE2991 for centrifugation followed by supernatant expelling. Bag filling, centrifugation, and expelling were repeated several times. Islets in pellet form were then purified by adding a gradient (bottom loading). Using this closed system 1098 +/- 489 IEQ per gram pancreas were purified with a total cell viability of 67 +/- 10% and a beta-cell viability of 41 +/- 13%. The total preparation time reduced to 6 h. After 24 h of cell culture the viability of beta-cells was still 56 +/- 10% and was only reduced after the addition of proapoptotic IL-1 and TNF-alpha to 40 +/- 4%, indicating that freshly isolated islets are not apoptotic. In conclusion, the closed system preparation is much faster, more effective, and less expensive than the traditional islet preparation. The closed system may be applicable for human islets preparations to restrict the need of clean room facilities for islet preparations to a minimum and may open the way for islet preparations without clean room demand.

In vitro effects of two silicate-based materials, Biodentine and BioRoot RCS, on dental pulp stem cells in models of reactionary and reparative dentinogenesis

PubMed Central

Loison-Robert, Ludwig Stanislas; Berbar, Tsouria; Isaac, Juliane; Berdal, Ariane; Simon, Stéphane

2018-01-01

Background Calcium silicate-based cements are biomaterials with calcium oxide and carbonate filler additives. Their properties are close to those of dentin, making them useful in restorative dentistry and endodontics. The aim of this study was to evaluate the in vitro biological effects of two such calcium silicate cements, Biodentine (BD) and Bioroot (BR), on dental stem cells in both direct and indirect contact models. The two models used aimed to mimic reparative dentin formation (direct contact) and reactionary dentin formation (indirect contact). An original aspect of this study is the use of an interposed thin agarose gel layer to assess the effects of diffusible components from the materials. Results The two biomaterials were compared and did not modify dental pulp stem cell (DPSC) proliferation. BD and BR showed no significant cytotoxicity, although some cell death occurred in direct contact. No apoptosis or inflammation induction was detected. A striking increase of mineralization induction was observed in the presence of BD and BR, and this effect was greater in direct contact. Surprisingly, biomineralization occurred even in the absence of mineralization medium. This differentiation was accompanied by expression of odontoblast-associated genes. Exposure by indirect contact did not stimulate the induction to such a level. Conclusion These two biomaterials both seem to be bioactive and biocompatible, preserving DPSC proliferation, migration and adhesion. The observed strong mineralization induction through direct contact highlights the potential of these biomaterials for clinical application in dentin-pulp complex regeneration. PMID:29370163

Ecotoxicity of wastes in avoidance tests with Enchytraeus albidus, Enchytraeus crypticus and Eisenia fetida (Oligochaeta).

PubMed

Kobeticová, Klára; Hofman, Jakub; Holoubek, Ivan

2010-04-01

Contact bioassays are important for testing the ecotoxicity of solid materials. However, survival and reproduction tests are often not practical due to their duration which may last for several weeks. Avoidance tests with soil invertebrates may offer an alternative or extension to the classic test batteries due to their short duration (days rather than weeks) and due to a sensitive sub-acute endpoint (behavior). (a) to evaluate the effects of three solid industrial wastes (incineration ash, contaminated wood chips and contaminated soil) on three Oligochaeta species (enchytraeids Enchytraeusalbidus, Enchytraeus crypticus and earthworm Eisenia fetida) in avoidance tests; (b) to compare the sensitivity among the species and to compare results of avoidance test to reproduction tests; (c) to elucidate if measuring the weight in the earthworm avoidance test could be reasonable additional endpoint. Avoidance mostly increased with the increasing percent of waste in the mixture showing a dose-response curve. E. fetida was the most sensitive species and E. crypticus the least one. An additional endpoint, (changes in weight after two-day exposure) was not found to be more sensitive than avoidance reaction, but it confirmed that earthworms staying in the highest concentrations of the waste mixture were affected showing apparent weight reduction. Our results indicate that avoidance tests with earthworms and enchytraeids are feasible for waste testing. Copyright 2009 Elsevier Ltd. All rights reserved.

Incidence of Leptospirosis infection in the East Zone of Sao Paulo City, Brazil

PubMed Central

2013-01-01

Background Leptospirosis is a zoonosis which is spread through contamined running water. This contaminations is seriously affected by the flooding which occurs in the area surrounding the Aricanduva river. The transmission of the disease results mainly from the contact of water with soil contaminated by the urine of infected animals. We aimed to conduct an epidemiological survey on Leptospirosis cases in Sao Paulo East Zone area. Method The analysis conducted in this study was based on data collected from the health authorities of that region close the Aricanduva river between 2007 and 2008 years, which give the rates of confirmed cases, mortality and death from human Leptospirosis. Other information concerned with the relationships among rainfall index, points of flooding and incidence of Leptospirosis. Results We observed a direct and important water contamination. Records of flooding points and dates of the reported cases in the region showed a direct relationship from which the period of higher rainfall also recorded an increase in cases. The annual record of the city and the region and rainfall regions also presented correlation. Conclusion The association between the indices of flooding and Leptospirosis cases indicates that preventive measures are necessary to avoid exposing the community. PMID:23672682

Cluster of Ebola Virus Disease, Bong and Montserrado Counties, Liberia.

PubMed

Nyenswah, Tolbert G; Fallah, Mosaka; Calvert, Geoffrey M; Duwor, Stanley; Hamilton, E Dutch; Mokashi, Vishwesh; Arzoaquoi, Sampson; Dweh, Emmanuel; Burbach, Ryan; Dlouhy, Diane; Oeltmann, John E; Moonan, Patrick K

2015-07-01

Lack of trust in government-supported services after the death of a health care worker with symptoms of Ebola resulted in ongoing Ebola transmission in 2 Liberia counties. Ebola transmission was facilitated by attempts to avoid cremation of the deceased patient and delays in identifying and monitoring contacts.

40 CFR 1039.625 - What requirements apply under the program for equipment-manufacturer flexibility?

Code of Federal Regulations, 2011 CFR

2011-07-01

... is manufactured. (4) An e-mail address and phone number to contact for further information, or a Web... secondary engine manufacturers. (l) [Reserved] (m) Additional exemptions for technical or engineering... avoided with reasonable discretion have resulted in technical or engineering problems that prevent you...

40 CFR 180.513 - Chlorfenapyr; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

... after each use of the product. (iv) Contamination of food or food contact surfaces shall be avoided...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... residues of chlorfenapyr in or on all food commodities (other than those covered by a higher tolerance as a...

A Coaxial Dual-element Focused Ultrasound Probe for Guidance of Epidural Catheterization: An Experimental Study.

PubMed

Dong, Guo-Chung; Chiu, Li-Chen; Ting, Chien-Kun; Hsu, Jia-Ruei; Huang, Chih-Chung; Chang, Yin; Chen, Gin-Shin

2017-09-01

Ultrasound guidance for epidural block has improved clinical blind-trial problems but the design of present ultrasonic probes poses operating difficulty of ultrasound-guided catheterization, increasing the failure rate. The purpose of this study was to develop a novel ultrasonic probe to avoid needle contact with vertebral bone during epidural catheterization. The probe has a central circular passage for needle insertion. Two focused annular transducers are deployed around the passage for on-axis guidance. A 17-gauge insulated Tuohy needle containing the self-developed fiber-optic-modified stylet was inserted into the back of the anesthetized pig, in the lumbar region under the guidance of our ultrasonic probe. The inner transducer of the probe detected the shallow echo signals of the peak-peak amplitude of 2.8 V over L3 at the depth of 2.4 cm, and the amplitude was decreased to 0.8 V directly over the L3 to L4 interspace. The outer transducer could detect the echoes from the deeper bone at the depth of 4.5 cm, which did not appear for the inner transducer. The operator tilted the probe slightly in left-right and cranial-caudal directions until the echoes at the depth of 4.5 cm disappeared, and the epidural needle was inserted through the central passage of the probe. The needle was advanced and stopped when the epidural space was identified by optical technique. The needle passed without bone contact. Designs of the hollow probe for needle pass and dual transducers with different focal lengths for detection of shallow and deep vertebrae may benefit operation, bone/nonbone identification, and cost.

Colour change in cyanosis and the confusions of congenital colour vision deficient observers.

PubMed

McNamara, Renae; Taylor, Clair M; McKenzie, David K; Coroneo, Minas T; Dain, Stephen J

2010-09-01

Visual recognition of cyanosis is an important clinical activity. While pulse oximetry is almost universal in the hospital environment, there are circumstances where it is not available or may be unreliable. Cyanosis recognition is affected by lighting colour. In addition, there is, mainly anecdotal, evidence that people with greater colour vision deficiencies (CVDs) have particular difficulty and there is no effective lighting strategy to assist in the observation. The change of blood colour with oxygenation has been shown to lie close to the direction of colour confusions made by congenital red-green dichromats. The important sites of observation are lips, nail beds and palm creases. 10 subjects who were known to be chronically hypoxaemic were recruited from the chronic respiratory program. Their blood oxygen saturation (SpO(2)) varied from 84% to 96% pre-exercise, and 61-84% post-exercise. Ten normal subjects were recruited whose SpO(2) was 99% or 100%. The spectral radiances of lips, nail beds and palm creases were measured using a telespectroradiometer and compared with the spectral radiances of a white tile of known spectral reflectances measured in the same location. This is a non-contact method of measurement, avoiding the blanching caused by pressure of contact methods. The spectral reflectances were calculated, and the chromaticities calculated for a Planckian radiator T = 4000K. Measurements on lips yielded the most consistent results. The colour changes pre- and post-exercise and compared with normal colour lie generally along a deutan confusion line. These results show the direction of the colour change and confirm the, previously anecdotal, difficulties in detecting cyanosis by observers with CVDs. © 2010 The Authors, Ophthalmic and Physiological Optics © 2010 The College of Optometrists.

Small but wise: Common marmosets (Callithrix jacchus) use acoustic signals as cues to avoid interactions with blonde capuchin monkeys (Sapajus flavius).

PubMed

Bastos, Monique; Medeiros, Karolina; Jones, Gareth; Bezerra, Bruna

2018-03-01

Vocalizations are often used by animals to communicate and mediate social interactions. Animals may benefit from eavesdropping on calls from other species to avoid predation and thus increase their chances of survival. Here we use both observational and experimental evidence to investigate eavesdropping and how acoustic signals may mediate interactions between two sympatric and endemic primate species (common marmosets and blonde capuchin monkeys) in a fragment of Atlantic Rainforest in Northeastern Brazil. We observed 22 natural vocal encounters between the study species, but no evident visual or physical contact over the study period. These two species seem to use the same area throughout the day, but at different times. We broadcasted alarm and long distance calls to and from both species as well as two control stimuli (i.e., forest background noise and a loud call from an Amazonian primate) in our playback experiments. Common marmosets showed anti-predator behavior (i.e., vigilance and flight) when exposed to blonde capuchin calls both naturally and experimentally. However, blonde capuchin monkeys showed no anti-predator behavior in response to common marmoset calls. Blonde capuchins uttered long distance calls and looked in the direction of the speaker following exposure to their own long distance call, whereas they fled when exposed to their own alarm calls. Both blonde capuchin monkeys and common marmosets showed fear behaviors in response to the loud call from a primate species unknown to them, and showed no apparent response to the forest background noise. Common marmoset responses to blonde capuchin calls suggests that the latter is a potential predator. Furthermore, common marmosets appear to be eavesdropping on calls from blonde capuchin monkeys to avoid potentially costly encounters with them. © 2018 Wiley Periodicals, Inc.

Self-esteem in Early Adolescence as Predictor of Depressive Symptoms in Late Adolescence and Early Adulthood: The Mediating Role of Motivational and Social Factors.

PubMed

Masselink, M; Van Roekel, E; Oldehinkel, A J

2018-05-01

Ample research has shown that low self-esteem increases the risk to develop depressive symptoms during adolescence. However, the mechanism underlying this association remains largely unknown, as well as how long adolescents with low self-esteem remain vulnerable to developing depressive symptoms. Insight into this mechanism may not only result in a better theoretical understanding but also provide directions for possible interventions. To address these gaps in knowledge, we investigated whether self-esteem in early adolescence predicted depressive symptoms in late adolescence and early adulthood. Moreover, we investigated a cascading mediational model, in which we focused on factors that are inherently related to self-esteem and the adolescent developmental period: approach and avoidance motivation and the social factors social contact, social problems, and social support. We used data from four waves of the TRAILS study (N = 2228, 51% girls): early adolescence (mean age 11 years), middle adolescence (mean age 14 years), late adolescence (mean age 16 years), and early adulthood (mean age 22 years). Path-analyses showed that low self-esteem is an enduring vulnerability for developing depressive symptoms. Self-esteem in early adolescence predicted depressive symptoms in late adolescence as well as early adulthood. This association was independently mediated by avoidance motivation and social problems, but not by approach motivation. The effect sizes were relatively small, indicating that having low self-esteem is a vulnerability factor, but does not necessarily predispose adolescents to developing depressive symptoms on their way to adulthood. Our study contributes to the understanding of the mechanisms underlying the association between self-esteem and depressive symptoms, and has identified avoidance motivation and social problems as possible targets for intervention.

Three distinct mechanisms predominate in non-contact anterior cruciate ligament injuries in male professional football players: a systematic video analysis of 39 cases

PubMed Central

Waldén, Markus; Krosshaug, Tron; Bjørneboe, John; Andersen, Thor Einar; Faul, Oliver

2015-01-01

Background Current knowledge on anterior cruciate ligament (ACL) injury mechanisms in male football players is limited. Aim To describe ACL injury mechanisms in male professional football players using systematic video analysis. Methods We assessed videos from 39 complete ACL tears recorded via prospective professional football injury surveillance between 2001 and 2011. Five analysts independently reviewed all videos to estimate the time of initial foot contact with the ground and the time of ACL tear. We then analysed all videos according to a structured format describing the injury circumstances and lower limb joint biomechanics. Results Twenty-five injuries were non-contact, eight indirect contact and six direct contact injuries. We identified three main categories of non-contact and indirect contact injury situations: (1) pressing (n=11), (2) re-gaining balance after kicking (n=5) and (3) landing after heading (n=5). The fourth main injury situation was direct contact with the injured leg or knee (n=6). Knee valgus was frequently seen in the main categories of non-contact and indirect contact playing situations (n=11), but a dynamic valgus collapse was infrequent (n=3). This was in contrast to the tackling-induced direct contact situations where a knee valgus collapse occurred in all cases (n=3). Conclusions Eighty-five per cent of the ACL injuries in male professional football players resulted from non-contact or indirect contact mechanisms. The most common playing situation leading to injury was pressing followed by kicking and heading. Knee valgus was frequently seen regardless of the playing situation, but a dynamic valgus collapse was rare. PMID:25907183

A randomized controlled trial comparing three invitation strategies in a breast cancer screening program.

PubMed

Segura, J M; Castells, X; Casamitjana, M; Macià, F; Porta, M; Katz, S J

2001-10-01

The objective of this study was to compare the response received by a population-based breast cancer screening program, according to three different invitation strategies: letters sent by mail from the program (program group), letters sent by mail from the Primary Health Care Team (PHT group), and direct contact through a trained professional (direct contact group). We used a cluster-randomized controlled trial with assignment to invitation group using home address. Nine hundred eighty-six women of Barcelona (Spain), ages 50 to 64 years, were invited to participate in the program. The main outcome used was the response rate after the first invitation. Five hundred sixty-four women accepted the invitation (57.2%). The highest response rate was achieved in the direct contact group (63.5%), followed by the PHT group (55.6%), the program group being the one that attained the lowest response rate (52.1%). The direct contact group had a higher probability of participating than the PHT group (RR = 1.14, P = 0.037) or the program group (RR = 1.22, P = 0.003). The response rate in the direct contact group was 72.1% when the letter was received by the subject herself. The increase in response occurred particularly among women of lower educational level. Inviting women to participate in a breast cancer screening program through direct contact by trained personnel increased participation rate compared with mailed-letter methods. The positive effect appeared restricted to women with lower educational levels. Copyright 2001 American Health Foundation and Academic Press.

Cross-Cultural Differences in Self-Reported Touch Avoidance.

ERIC Educational Resources Information Center

Jones, Tricia S.; Remland, Martin S.

Two hundred forty-eight male and female subjects from United States, Mediterranean, Near East, and Far East cultures completed a touch avoidance measure in a study examining cultural differences in touching behavior. Factor analysis of the instrument yielded four factors: opposite sex, other-directed same sex, kissing, and self-directed same sex.…

Smoking-specific experiential avoidance cognition: explanatory relevance to pre- and post-cessation nicotine withdrawal, craving, and negative affect.

PubMed

Farris, Samantha G; Zvolensky, Michael J; Schmidt, Norman B

2015-05-01

Negative-reinforcement based cognitive processes have been implicated in the maintenance of cigarette smoking. Given the expectation that smoking will attenuate aversive internal experiences, smokers may be particularly unwilling to experience or remain in contact with smoking-related distress (i.e., experiential avoidance). Yet, there is little known about a cognitive-based process termed smoking-specific experiential avoidance with regard to withdrawal, craving, or negative affect during a quit attempt. Data were collected from adult daily smokers (n = 259) participating in a larger smoking cessation trial. Pre- and post-quit experiences of nicotine withdrawal, craving, and negative affect were examined in terms of cognitive-based smoking-specific experimental avoidance, measured by the Avoidance and Inflexibility Scale (AIS). Results indicated that baseline smoking-specific experiential avoidance was associated with greater overall levels of withdrawal, craving, and negative affect at treatment initiation (pre-cessation). Reductions in smoking-specific experiential avoidance from baseline to quit day were associated with increased likelihood of quit day abstinence. Such reductions were also predictive of lower levels of nicotine withdrawal, craving, and negative affect on quit day. Also, less reduction in experiential avoidance was associated with experiencing greater withdrawal in the early phase of quitting. The impact of cognitive-based experiential avoidance pertaining to smoking impacts both pre- and post-cessation experiences in terms of negative affect, withdrawal, and smoking cravings and may represent an important treatment target. Copyright © 2014 Elsevier Ltd. All rights reserved.

Follow-up after telephone consultations at out-of-hours primary care.

PubMed

Huibers, Linda; Koetsenruijter, Jan; Grol, Richard; Giesen, Paul; Wensing, Michel

2013-01-01

After a contact with a primary care physician (PCP) cooperative for out-of-hours care, many patients have subsequent contact with health care. Little is known about the factors associated with these follow-up contacts. The objective of this study was to examine whether patient experiences with nurse telephone consultations and the cooperative's organizational characteristics were associated with the probability of follow-up contact. We conducted a cross-sectional study of patients attending 16 Dutch PCP cooperatives (2009 to 2011) using a validated questionnaire to measure patient experiences with nurse telephone consultations and patient-reported follow-up. Participating cooperatives provided information on 12 organizational characteristics. Multilevel regression modeling was used to identify associations. A total of 7039 patients returned a questionnaire (50.4%), of which 5678 were complete. About half of patients reported a follow-up contact (47%). Regression analyses showed increasing probability of follow-up contact in patients with higher age (≥65 years; odds ratio [OR], 2.39), patients receiving a home visit (OR, 1.32), and cooperatives with a higher percentage of telephone consultations (OR, 1.02) and a decreased probability among patients with more positive experiences with a nurse via telephone contact (OR, 0.68). Although follow-up contacts can be medically required, a substantial number of contacts seem to be not required and thus are potentially avoidable (eg, by changes in work routine and communication).

Cadherin-11 Mediates Contact Inhibition of Locomotion during Xenopus Neural Crest Cell Migration

PubMed Central

Becker, Sarah F. S.; Mayor, Roberto; Kashef, Jubin

2013-01-01

Collective cell migration is an essential feature both in embryonic development and cancer progression. The molecular mechanisms of these coordinated directional cell movements still need to be elucidated. The migration of cranial neural crest (CNC) cells during embryogenesis is an excellent model for collective cell migration in vivo. These highly motile and multipotent cells migrate directionally on defined routes throughout the embryo. Interestingly, local cell-cell interactions seem to be the key force for directionality. CNC cells can change their migration direction by a repulsive cell response called contact inhibition of locomotion (CIL). Cell protrusions collapse upon homotypic cell-cell contact and internal repolarization leads to formation of new protrusions toward cell-free regions. Wnt/PCP signaling was shown to mediate activation of small RhoGTPase RhoA and inhibition of cell protrusions at the contact side. However, the mechanism how a cell recognizes the contact is poorly understood. Here, we demonstrate that Xenopus cadherin-11 (Xcad-11) mediated cell-cell adhesion is necessary in CIL for directional and collective migration of CNC cells. Reduction of Xcad-11 adhesive function resulted in higher invasiveness of CNC due to loss of CIL. Additionally, transplantation analyses revealed that CNC migratory behaviour in vivo is non-directional and incomplete when Xcad-11 adhesive function is impaired. Blocking Wnt/PCP signaling led to similar results underlining the importance of Xcad-11 in the mechanism of CIL and directional migration of CNC. PMID:24392028

Simulation of between-farm transmission of porcine reproductive and respiratory syndrome virus in Ontario, Canada using the North American Animal Disease Spread Model.

PubMed

Thakur, Krishna K; Revie, Crawford W; Hurnik, Daniel; Poljak, Zvonimir; Sanchez, Javier

2015-03-01

Porcine reproductive and respiratory syndrome (PRRS), a viral disease of swine, has major economic impacts on the swine industry. The North American Animal Disease Spread Model (NAADSM) is a spatial, stochastic, farm level state-transition modeling framework originally developed to simulate highly contagious and foreign livestock diseases. The objectives of this study were to develop a model to simulate between-farm spread of a homologous strain of PRRS virus in Ontario swine farms via direct (animal movement) and indirect (sharing of trucks between farms) contacts using the NAADSM and to compare the patterns and extent of outbreak under different simulated conditions. A total of 2552 swine farms in Ontario province were allocated to each census division of Ontario and geo-locations of the farms were randomly generated within the agriculture land of each Census Division. Contact rates among different production types were obtained using pig movement information from four regions in Canada. A total of 24 scenarios were developed involving various direct (movement of infected animals) and indirect (pig transportation trucks) contact parameters in combination with alternating the production type of the farm in which the infection was seeded. Outbreaks were simulated for one year with 1000 replications. The median number of farms infected, proportion of farms with multiple outbreaks and time to reach the peak epidemic were used to compare the size, progression and extent of outbreaks. Scenarios involving spread only by direct contact between farms resulted in outbreaks where the median percentage of infected farms ranged from 31.5 to 37% of all farms. In scenarios with both direct and indirect contact, the median percentage of infected farms increased to a range from 41.6 to 48.6%. Furthermore, scenarios with both direct and indirect contact resulted in a 44% increase in median epidemic size when compared to the direct contact scenarios. Incorporation of both animal movements and the sharing of trucks within the model indicated that the effect of direct and indirect contact may be nonlinear on outbreak progression. The increase of 44% in epidemic size when indirect contact, via sharing of trucks, was incorporated into the model highlights the importance of proper biosecurity measures in preventing transmission of the PRRS virus. Simulation of between-farm spread of the PRRS virus in swine farms has highlighted the relative importance of direct and indirect contact and provides important insights regarding the possible patterns and extent of spread of the PRRS virus in a completely susceptible population with herd demographics similar to those found in Ontario, Canada. Copyright © 2015 Elsevier B.V. All rights reserved.

Polymer Hydrogel/Polybutadiene/Iron Oxide Nanoparticle Hybrid Actuators for the Characterization of NiTi Implants

PubMed Central

Jeličić, Aleksandra; Friedrich, Alwin; Jeremić, Katarina; Siekmeyer, Gerd; Taubert, Andreas

2009-01-01

One of the main issues with the use of nickel titanium alloy (NiTi) implants in cardiovascular implants (stents) is that these devices must be of very high quality in order to avoid subsequent operations due to failing stents. For small stents with diameters below ca. 2 mm, however, stent characterization is not straightforward. One of the main problems is that there are virtually no methods to characterize the interior of the NiTi tubes used for fabrication of these tiny stents. The current paper reports on a robust hybrid actuator for the characterization of NiTi tubes prior to stent fabrication. The method is based on a polymer/hydrogel/magnetic nanoparticle hybrid material and allows for the determination of the inner diameter at virtually all places in the raw NiTi tubes. Knowledge of the inner structure of the raw NiTi tubes is crucial to avoid regions that are not hollow or regions that are likely to fail due to defects inside the raw tube. The actuator enables close contact of a magnetic polymer film with the inner NiTi tube surface. The magnetic signal can be detected from outside and be used for a direct mapping of the tube interior. As a result, it is possible to detect critical regions prior to expensive and slow stent fabrication processes.

Agonistic behaviour in juvenile southern rock lobster, Jasusedwardsii (Decapoda, Palinuridae): implications for developing aquaculture.

PubMed

Carter, Chris G; Westbury, Heath; Crear, Bradley; Simon, Cedric; Thomas, Craig

2014-01-01

The Southern rock lobster, Jasusedwardsii, is a temperate species of spiny lobster with established well managed fisheries in Australia and New Zealand. It has also been under consideration as a species with aquaculture potential. Agonistic behaviour has important consequences under aquaculture conditions that encompass direct effects, such as damage or death of protagonists, and indirect effects on growth that relate to resource access, principally food and refuge. This study aimed to identify and characterize behaviours and to make a preliminary investigation of their occurrence under tank culture. Juvenile Jasusedwardsii were examined in a flow-through seawater system using a remote video camera system. Twenty-nine behaviours were divided into three sub-groups: aggressive (11), avoidance (6) and others (12). Aggressive behaviours included attacks, pushing, lifting, clasping and carrying an opponent. Avoidance behaviours included moving away in a backwards-, forwards- or side-stepping motion as well as with more vigorous tail flips. These behaviours were components of twelve behavioural groups that described contact, attack and displacement between individuals. Activity was crepuscular with two clear peaks, one in the morning and the other in the evening. The occurrence of behavioural groups was not different between the morning and evening. The frequency of aggressive behaviours was not affected by changes made to stocking density or access to food. The implications of agonistic behaviours are discussed further in relation to developing aquaculture.

Properties of perpendicular-anisotropy magnetic tunnel junctions fabricated over the bottom electrode contact

NASA Astrophysics Data System (ADS)

Miura, Sadahiko; Honjo, Hiroaki; Kinoshita, Keizo; Tokutome, Keiichi; Koike, Hiroaki; Ikeda, Shoji; Endoh, Tetsuo; Ohno, Hideo

2015-04-01

Perpendicular-anisotropy magnetic tunnel junctions (MTJs) were prepared on four substrate geometries, i.e., directly on the axis of the bottom electrode contact, directly off the axis of the bottom electrode contact, on the axis of the bottom electrode contact with a polished bottom electrode, and off the axis of the bottom electrode contact with a polished bottom electrode. Electrical shorts were observed for direct on-axis geometry at a certain extent, whereas there were no electrical shorts for the other three geometries. The MR ratio/σR, JC0, and thermal stability factor of the devices for polish on-axis geometry were almost the same as those for polish off-axis geometry. From TEM observations of the polish on-axis device, the interface between the bottom contact and the base electrode was determined to be rough, whereas the MgO barrier layer was determined to be smooth, indicating that the polish process was effective for smooth magnetic tunnel junction fabrication over the bottom contact. MTJs for polish on-axis geometry eliminated the base electrode resistance and increased the magnetoresistance ratio. This technology contributes to the higher density of spin transfer torque magnetic random access memory.

The pathogenesis of highly virulent African Swine Fever virus in domestic pigs exposed via intraoropharyngeal, intranasopharyngeal, and intramuscular inoculation, and by direct contact with infected pigs

USDA-ARS?s Scientific Manuscript database

In order to optimize novel systems for African Swine Fever Virus (ASFV) vaccine development, domestic pigs were challenged with the highly virulent ASFV-Malawi strain via intraoropharyngeal (IOP), intranasopharyngeal (INP), intramuscular (IM), and direct contact (DC) routes. Direct challenge doses ...

A systematical analysis of in vivo contact forces on virtual catheter tip/tissue surface contact during cardiac mapping and intervention.

PubMed

Okumura, Yasuo; Johnson, Susan B; Bunch, T Jared; Henz, Benhur D; O'Brien, Christine J; Packer, Douglas L

2008-06-01

While catheter tip/tissue contact has been shown to be an important determinant of ablative lesions in in vitro studies, the impact of contact on the outcomes of mapping and ablation in the intact heart has not been evaluated. Twelve dogs underwent atrial ablation guided by the Senesitrade mark robotic catheter remote control system. After intracardiac ultrasound (ICE) validation of contact force measured by an in-line mechanical sensor, the relationship between contact force and individual lesion formation was established during irrigated-tipped ablation (flow 17 mL/sec) at 15 watts for 30 seconds. Minimal contact by ICE correlated with force of 4.7 +/- 5.8 grams, consistent contact 9.9 +/- 8.6 grams and tissue tenting produced 25.0 +/- 14.0 grams. Conversely, catheter tip/tissue contact by ICE was predicted by contact force. A contact force of 10-20 and > or =20 grams generated full-thickness, larger volume ablative lesions than that created with <10 grams (98 +/- 69 and 89 +/- 70 mm(3) vs 40 +/- 42 mm(3), P < 0.05). Moderate (10 grams) and marked contact (15-20 grams) application produced 1.5 X greater electroanatomic map volumes that were seen with minimal contact (5 grams) (26 +/- 3 cm(3) vs 33 +/- 6, 39 +/- 3 cm(3), P < 0.05). The electroanatomic map/CT merge process was also more distorted when mapping was generated at moderate to marked contact force. This study shows that mapping and ablation using a robotic sheath guidance system are critically dependent on generated force. These findings suggest that ablative lesion size is optimized by the application of 10-20 grams of contact force, although mapping requires lower-force application to avoid image distortions.

Contact frequency and cognitive health among older adults in Israel.

PubMed

Schwartz, Ella; Khalaila, Rabia; Litwin, Howard

2018-05-03

The current study set out to examine the links between contact frequency with one's social network and cognitive health in later life. It assessed both direct and indirect pathways and the possible role of ethnicity in the effect of the social network on cognitive function. We used data from adults aged 50 and above, which was collected in Israel as part of the Survey of Ageing, Retirement and Health (SHARE). A moderated mediation analysis was conducted to test the direct and indirect associations between contact frequency and cognitive function, as well as the moderation of these associations by population group. Three population groups were examined - veteran-Jews, Arabs and immigrants from the former Soviet Union. Contact frequency with the close social milieu was found to be directly positively related to cognitive function. The association was also mediated by depressive symptoms, such that frequent contacts were linked to cognitive health via reduced depressive symptoms. This indirect link differed, however, among the three population groups. Contact frequency is important for cognitive health in the second half of life, and it operates both directly and by decreasing depressive symptoms. However, these links are not found among all ethnic groups and may, therefore, depend on the culture and social norms of each group and the meaning attributed to social ties.

Antibacterial properties of aged dental cements evaluated by direct-contact and agar diffusion tests.

PubMed

Lewinstein, Israel; Matalon, Shlomo; Slutzkey, Shimshon; Weiss, Ervin I

2005-04-01

Since failure of fixed partial dentures is most frequently caused by caries, it would be advantageous if cements possessed antibacterial properties. The purpose of this study was to evaluate the antibacterial properties of 3 dental cements using the direct-contact test and agar diffusion test. For the direct-contact test, wells (n = 4) of microtiter plates were coated with the tested cements (Harvard cement, Duralon, and Ketac-Cem) while Streptococcus mutans suspension was placed directly on the cements. Bacterial growth was evaluated by a temperature-controlled microplate spectrophotometer. Eight wells of bacteria without the tested cements served as the positive control. Six wells of the tested cement without bacteria served as the negative control. For the agar diffusion test, triplicate specimens of freshly mixed cements were poured into uniform wells (5 mm in diameter) punched in the agar plates inoculated with Streptococcus mutans . After incubation at 37 degrees C for 24 hours, the agar plates were examined for bacterial growth and the diameter of the halo formed in the bacterial lawn was measured. In both tests, each cement was mixed in 2 different powder/liquid ratios. For the direct-contact test, data were initially recorded after 1 hour of incubation. Additional experiments were performed on specimens that were aged for 24 hours, 1 week, 1 month, and 3 months before assessment by either direct-contact test or agar diffusion test. The data were subjected to 1-way ANOVA with the Tukey post hoc test (alpha=.05). Compared with the control group, Duralon and Harvard cements demonstrated antibacterial properties even after 3 months with the direct-contact test (P <.002), while Ketac-Cem exhibited no antibacterial properties. In the agar diffusion test, no antibacterial activity was observed for any of the tested cements. The different powder/liquid ratios had a negligible effect on the antibacterial properties of the tested cements. Within the limitations of this study, Duralon and Harvard cements possessed prolonged antibacterial properties, while Ketac-Cem exhibited no antibacterial activity. The direct-contact test may be a more suitable test than the agar diffusion test to evaluate antibacterial properties of definitive cements.

Human-directed social behaviour in dogs shows significant heritability.

PubMed

Persson, M E; Roth, L S V; Johnsson, M; Wright, D; Jensen, P

2015-04-01

Through domestication and co-evolution with humans, dogs have developed abilities to attract human attention, e.g. in a manner of seeking assistance when faced with a problem solving task. The aims of this study were to investigate within breed variation in human-directed contact seeking in dogs and to estimate its genetic basis. To do this, 498 research beagles, bred and kept under standardized conditions, were tested in an unsolvable problem task. Contact seeking behaviours recorded included both eye contact and physical interactions. Behavioural data was summarized through a principal component analysis, resulting in four components: test interactions, social interactions, eye contact and physical contact. Females scored significantly higher on social interactions and physical contact and age had an effect on eye contact scores. Narrow sense heritabilities (h(2) ) of the two largest components were estimated at 0.32 and 0.23 but were not significant for the last two components. These results show that within the studied dog population, behavioural variation in human-directed social behaviours was sex dependent and that the utilization of eye contact seeking increased with age and experience. Hence, heritability estimates indicate a significant genetic contribution to the variation found in human-directed social interactions, suggesting that social skills in dogs have a genetic basis, but can also be shaped and enhanced through individual experiences. This research gives the opportunity to further investigate the genetics behind dogs' social skills, which could also play a significant part into research on human social disorders such as autism. © 2015 John Wiley & Sons Ltd and International Behavioural and Neural Genetics Society.

Effect of direct and indirect contact with mental illness on dangerousness and social distance.

PubMed

Lee, Minhwa; Seo, Mikyung

2018-03-01

This study is based on the contact hypothesis that contact with mental illness is the most effective anti-stigma strategy. This study aims to analyze which form of contact can most effectively decrease the dangerousness and social distance associated with schizophrenia, depression and alcoholism. In total, 573 Korean adults ( M age  = 43.71 years, standard deviation ( SD) = 13.41; 54.1% male, 45.9% female) were surveyed about randomly assigned vignettes of schizophrenia, depression and alcoholism. The participants were questioned on the dangerousness and social distance associated with the assigned vignette, as well as direct and indirect contact experience with the mental illness. Two-way analysis of variance (ANOVA) was used to determine the main effect and interaction effect that the type of mental illness and contact experience have on the two dependent variables (dangerousness and social distance). The findings show that the type of mental illness has a significant main effect on dangerousness and social distance, but contact type only has a significant main effect on social distance. Moreover, the two independent variables (mental illness subtype and contact experience) have an interaction effect on two dependent variables (dangerousness and social distance). Therefore, the anti-stigma effect of contact varies according to the type of mental illness. Our findings suggest that appropriate anti-stigma strategies are required for each type of mental illness. Considering that opportunities for direct contact with persons with mental illness are highly limited, it is necessary to actively utilize indirect contact.

Magneto-inductive skin sensor for robot collision avoidance: A new development

NASA Technical Reports Server (NTRS)

Chauhan, D. S.; Dehoff, Paul H.

1989-01-01

Safety is a primary concern for robots operating in space. The tri-mode sensor addresses that concern by employing a collision avoidance/management skin around the robot arms. This rf-based skin sensor is at present a dual mode (proximity and tactile). The third mode, pyroelectric, will complement the other two. The proximity mode permits the robot to sense an intruding object, to range the object, and to detect the edges of the object. The tactile mode permits the robot to sense when it has contacted an object, where on the arm it has made contact, and provides a three-dimensional image of the shape of the contact impression. The pyroelectric mode will be added to permit the robot arm to detect the proximity of a hot object and to add sensing redundancy to the two other modes. The rf-modes of the sensing skin are presented. These modes employ a highly efficient magnetic material (amorphous metal) in a sensing technique. This results in a flexible sensor array which uses a primarily inductive configuration to permit both capacitive and magnetoinductive sensing of object; thus optimizing performance in both proximity and tactile modes with the same sensing skin. The fundamental operating principles, design particulars, and theoretical models are provided to aid in the description and understanding of this sensor. Test results are also given.

Protecting Yourself From Shingles | NIH MedlinePlus the Magazine

MedlinePlus

... with shingles can spread the disease through direct contact with the rash when the rash is in the blister phase. ... person who has never had chickenpox through direct contact with the rash. The person exposed would develop chickenpox, not shingles. ...

76 FR 62321 - Airworthiness Directives; Aviation Communication & Surveillance Systems (ACSS) Traffic Alert and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

... Communication & Surveillance Systems (ACSS) Traffic Alert and Collision Avoidance System (TCAS) Units AGENCY... certain Aviation Communication & Surveillance Systems (ACSS) traffic alert and collision avoidance system...) traffic alert and collision avoidance system (TCAS) units with part numbers identified in ACSS Technical...

75 FR 81512 - Airworthiness Directives; Various Aviation Communication & Surveillance Systems (ACSS) Traffic...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-28

... Communication & Surveillance Systems (ACSS) Traffic Alert and Collision Avoidance System (TCAS) Units AGENCY... & Surveillance Systems (ACSS) Traffic Alert and Collision Avoidance System (TCAS) units during a flight test over... applies to Aviation Communication & Surveillance Systems (ACSS) Traffic Alert and Collision Avoidance...

Effects of electrocautery on transvenous lead insulation materials.

PubMed

Lim, Kiam-Khiang; Reddy, Shantanu; Desai, Shrojal; Smelley, Matthew; Kim, Susan S; Beshai, John F; Lin, Albert C; Burke, Martin C; Knight, Bradley P

2009-04-01

Insulation defects are a leading cause of transvenous lead failure. The purpose of this study was to determine the effects of electrocautery on transvenous lead insulation materials. A preparation was done to simulate dissection of a transvenous lead from tissues. Radiofrequency energy was delivered using a standard cautery blade at outputs of 10, 20, and 30 W, for 3 and 6 seconds, using parallel and perpendicular blade orientations on leads with outermost insulations of silicone rubber, polyurethane, and silicone-polyurethane copolymer. Damage to each lead segment was classified after visual and microscopic analysis. Significant insulation damage occurred to almost all polyurethane leads. Full insulation breaches were observed with 30 W regardless of application duration with a parallel direction and with all power outputs with a perpendicular direction. Thermal insulation damage to copolymer insulation was similar to that of the polyurethane leads. In contrast, there was no thermal damage to silicone leads, regardless of the power output and duration of power delivery. However, mechanical insulation damage was observed to all silicone leads when at least 20 W was applied in a direction perpendicular to the lead. Polyurethane (PU55D) and copolymer materials have low thermal stability and are highly susceptible to thermal damage during cautery. Implanting physicians should be aware of the lead insulation materials being used during implant procedures and their properties. The use of direct contact cautery on transvenous leads should be minimized to avoid damage to the lead, especially on leads with polyurethane or copolymer outer insulations.

Attention to eye contact in the West and East: autonomic responses and evaluative ratings.

PubMed

Akechi, Hironori; Senju, Atsushi; Uibo, Helen; Kikuchi, Yukiko; Hasegawa, Toshikazu; Hietanen, Jari K

2013-01-01

Eye contact has a fundamental role in human social interaction. The special appearance of the human eye (i.e., white sclera contrasted with a coloured iris) implies the importance of detecting another person's face through eye contact. Empirical studies have demonstrated that faces making eye contact are detected quickly and processed preferentially (i.e., the eye contact effect). Such sensitivity to eye contact seems to be innate and universal among humans; however, several studies suggest that cultural norms affect eye contact behaviours. For example, Japanese individuals exhibit less eye contact than do individuals from Western European or North American cultures. However, how culture modulates eye contact behaviour is unclear. The present study investigated cultural differences in autonomic correlates of attentional orienting (i.e., heart rate) and looking time. Additionally, we examined evaluative ratings of eye contact with another real person, displaying an emotionally neutral expression, between participants from Western European (Finnish) and East Asian (Japanese) cultures. Our results showed that eye contact elicited stronger heart rate deceleration responses (i.e., attentional orienting), shorter looking times, and higher ratings of subjective feelings of arousal as compared to averted gaze in both cultures. Instead, cultural differences in the eye contact effect were observed in various evaluative responses regarding the stimulus faces (e.g., facial emotion, approachability etc.). The rating results suggest that individuals from an East Asian culture perceive another's face as being angrier, unapproachable, and unpleasant when making eye contact as compared to individuals from a Western European culture. The rating results also revealed that gaze direction (direct vs. averted) could influence perceptions about another person's facial affect and disposition. These results suggest that cultural differences in eye contact behaviour emerge from differential display rules and cultural norms, as opposed to culture affecting eye contact behaviour directly at the physiological level.

Attention to Eye Contact in the West and East: Autonomic Responses and Evaluative Ratings

PubMed Central

Akechi, Hironori; Senju, Atsushi; Uibo, Helen; Kikuchi, Yukiko; Hasegawa, Toshikazu; Hietanen, Jari K.

2013-01-01

Eye contact has a fundamental role in human social interaction. The special appearance of the human eye (i.e., white sclera contrasted with a coloured iris) implies the importance of detecting another person's face through eye contact. Empirical studies have demonstrated that faces making eye contact are detected quickly and processed preferentially (i.e., the eye contact effect). Such sensitivity to eye contact seems to be innate and universal among humans; however, several studies suggest that cultural norms affect eye contact behaviours. For example, Japanese individuals exhibit less eye contact than do individuals from Western European or North American cultures. However, how culture modulates eye contact behaviour is unclear. The present study investigated cultural differences in autonomic correlates of attentional orienting (i.e., heart rate) and looking time. Additionally, we examined evaluative ratings of eye contact with another real person, displaying an emotionally neutral expression, between participants from Western European (Finnish) and East Asian (Japanese) cultures. Our results showed that eye contact elicited stronger heart rate deceleration responses (i.e., attentional orienting), shorter looking times, and higher ratings of subjective feelings of arousal as compared to averted gaze in both cultures. Instead, cultural differences in the eye contact effect were observed in various evaluative responses regarding the stimulus faces (e.g., facial emotion, approachability etc.). The rating results suggest that individuals from an East Asian culture perceive another's face as being angrier, unapproachable, and unpleasant when making eye contact as compared to individuals from a Western European culture. The rating results also revealed that gaze direction (direct vs. averted) could influence perceptions about another person's facial affect and disposition. These results suggest that cultural differences in eye contact behaviour emerge from differential display rules and cultural norms, as opposed to culture affecting eye contact behaviour directly at the physiological level. PMID:23516627

Experiences of police contact among young adult recreational drug users: A qualitative study.

PubMed

Leslie, Ellen M; Cherney, Adrian; Smirnov, Andrew; Kemp, Robert; Najman, Jake M

2018-06-01

While young adults who engage in recreational drug use are at increased risk of contact with police, their experiences of police contact have been largely overlooked. In-depth qualitative interviews were conducted with 70 young adult amphetamine-type stimulant (ATS; i.e., ecstasy [MDMA] and methamphetamine) users who had experienced intensive alcohol and other drug-related police contact (e.g., being arrested, charged, or raided by police). These interviews focused on perceptions of personal experiences of alcohol and other drug-related police contact and general perceptions of police and policing and were conducted as part of a larger longitudinal study of drug use among a population-based sample of young adults from South-East Queensland, Australia. ATS users' perceptions of their personal interactions with police and general perceptions of police and policing were influenced by a number of factors, including police behaviour, prior contact with police, friends and family members' contact with police, and perceptions of their own behaviour leading to their contact with police. While a majority of ATS users reported that their contact with police had either a neutral or negative impact on their general perceptions of police and policing, some ATS users reported that police contact had a positive impact. For 70% of ATS users, police contact was reported to have had an impact on their substance use behaviours, resulting in either modification of their substance use behaviours to avoid further police contact or reduction in their substance use. These findings suggest that police contact among young adult ATS users can impact on both perceptions of police and policing and substance use behaviours, emphasising the importance of the quality and nature of police contact and its potential role in harm reduction. Copyright © 2018 Elsevier B.V. All rights reserved.

Articular contact pressures of meniscal repair techniques at various knee flexion angles.

PubMed

Flanigan, David C; Lin, Fang; Koh, Jason L; Zhang, Li-Qun

2010-07-13

Articular cartilage injury can occur after meniscal repair with biodegradable implants. Previous contact pressure analyses of the knee have been based on the tibial side of the meniscus at limited knee flexion angles. We investigated articular contact pressures on the posterior femoral condyle with different knee flexion angles and surgical repair techniques. Medial meniscus tears were repaired in 30 fresh bovine knees. Knees were mounted on a 6-degrees-of-freedom jig and statically loaded to 200 N at 45 degrees, 70 degrees, 90 degrees, and 110 degrees of knee flexion under 3 conditions: intact meniscus, torn meniscus, and meniscus after repair. For each repair, 3 sutures or biodegradable implants were used. A pressure sensor was used to determine the contact area and peak pressure. Peak pressures over each implant position were measured. Peak pressure increased significantly as knee flexion increased in normal, injured, and repaired knees. The change in peak pressure in knees with implant repairs was significantly higher than suture repairs at all knee flexion angles. Articular contact pressure on the posterior femoral condyle increased with knee flexion. Avoidance of deep knee flexion angles postoperatively may limit increases in articular contact pressures and potential chondral injury. Copyright 2010, SLACK Incorporated.

High voltage MOSFET devices and methods of making the devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Banerjee, Sujit; Matocha, Kevin; Chatty, Kiran

A SiC MOSFET device having low specific on resistance is described. The device has N+, P-well and JFET regions extended in one direction (Y-direction) and P+ and source contacts extended in an orthogonal direction (X-direction). The polysilicon gate of the device covers the JFET region and is terminated over the P-well region to minimize electric field at the polysilicon gate edge. In use, current flows vertically from the drain contact at the bottom of the structure into the JFET region and then laterally in the X direction through the accumulation region and through the MOSFET channels into the adjacent N+more » region. The current flowing out of the channel then flows along the N+ region in the Y-direction and is collected by the source contacts and the final metal. Methods of making the device are also described.« less

High voltage MOSFET devices and methods of making the devices

DOEpatents

Banerjee, Sujit; Matocha, Kevin; Chatty, Kiran

2015-12-15

A SiC MOSFET device having low specific on resistance is described. The device has N+, P-well and JFET regions extended in one direction (Y-direction) and P+ and source contacts extended in an orthogonal direction (X-direction). The polysilicon gate of the device covers the JFET region and is terminated over the P-well region to minimize electric field at the polysilicon gate edge. In use, current flows vertically from the drain contact at the bottom of the structure into the JFET region and then laterally in the X direction through the accumulation region and through the MOSFET channels into the adjacent N+ region. The current flowing out of the channel then flows along the N+ region in the Y-direction and is collected by the source contacts and the final metal. Methods of making the device are also described.

[Application of advanced engineering technologies to medical and rehabilitation fields].

PubMed

Fujie, Masakatsu

2012-07-01

The words "Japan syndrome" can now be heard increasingly through the media. Facing the approach of an elderly-dominated society, Robot Technology(RT)is expected to play an important role in Japan's medical, rehabilitation, and daily support fields. The industrial robot, which has already spread through the world with a great success in certain isolated environments by doing the work which is specialized for the thing with the hard known characteristic. By comparison, in the medical and rehabilitation fields, environments always change intricately, and individual characteristics differ from person to person. Furthermore, there are many times when a robot will be asked to directly interact with people. Moreover, the relation between a robot and a person turns into a relation which should involve contact flexibly according to a situation, and also turns into a relation which should avoid contact. In our group, we have so far developed practical rehabilitation and medical robots which can respond to difficulties such as environmental change and individual specificity. In developing rehabilitation robots, it is especially important to consider intuitive operability and individual differences. In addition, in developing medical robots, it is important to replace the experimental knowledge of surgeons to the mechanical quantitative properties. In this article, we introduce some practical examples of rehabilitation and medical robots interweaving several detailed technologies we have so far developed.

In vivo degradation effects of alloy MgNd2 in contact with mucous tissue.

PubMed

Seitz, J-M; Eifler, R; Weber, C; Lenarz, Th; Maier, H J; Durisin, M

2014-12-10

Magnesium alloys are currently being investigated for use as resorbable bio-materials. Various applications for magnesium based implant materials have already been presented. Currently, stents and structures that sustain diseased or narrowed vessels seem to be the most promising areas. This study focuses on the use of a magnesium fluoride (MgF 2 ) coated magnesium neodymium based alloy (MgNd2) and its use as a post-surgery stent material to avoid proliferation in the sinus region. Simple cylindrical shaped specimens were sewn to the sinus' mucosa of pigs and left in place for different periods of time to investigate the long-term corrosion resistance of the alloy and its coating during direct contact with physiological tissue. Investigations made within this study explicitly focused on the corrosive behavior of the alloy in the region of a physiological sinus. Thus, losses in mass and volume, and element analyses were considered to obtain information about the specimens' corrosion performance over time. Furthermore, micrographs support the alloy specific corrosion type analyses which focus on grain boundary effects. This study demonstrates the general in vivo applicability of fluoride coated MgNd2. The progress of corrosion was determined to be adequate and homogeneous over a total period of 180 days. This article is protected by copyright. All rights reserved. Copyright © 2014 Wiley Periodicals, Inc., A Wiley Company.

Understandings of reproductive tract infections in a peri-urban pueblo joven in Lima, Peru

PubMed Central

Hernández, Lisa Scipioni; Winch, Peter J; Parker, Kea; Gilman, Robert H

2006-01-01

Background Control programs for Reproductive Tract Infections (RTIs) typically focus on increasing awareness of risks associated with different forms of sexual contact, and pay little attention to how or why people may link RTIs to other features of their physical or social environments. This paper describes how women in a peri-urban pueblo joven located in the coastal desert surrounding Lima, Peru conceptualize the links between RTIs, sexual behaviour, personal hygiene, and the adverse environment in which they live. Methods We combined qualitative interviews and a participatory voting exercise to examine social and physical environmental influences on RTIs and gynaecologic symptom interpretation. Results Knowledge of RTIs in general was limited, although knowledge of AIDS was higher. Perceived causes of RTIs fell into three categories: sexual contact with infected persons, personal hygiene and exposure to the contaminated physical environment, with AIDS clearly related to sexual contact. The adverse environment is thought to be a major contributor to vaginal discharge, "inflamed ovaries" and urinary tract infection. The more remote parts of this periurban squatter settlement, characterized by blowing sand and dust and limited access to clean water, are thought to exhibit higher rates of RTIs as a direct result of the adverse environment found there. Stigma associated with RTIs often keeps women from seeking care or obtaining information about gynaecologic symptoms, and favours explanations that avoid mention of sexual practices. Conclusion The discrepancy between demonstrated disease risk factors and personal explanations influenced by local environmental conditions and RTI-related stigma poses a challenge for prevention programs. Effective interventions need to take local understandings of RTIs into account as they engage in dialogue with communities about prevention and treatment of RTIs. PMID:16670025

Health promotion interventions to prevent early childhood human influenza at the household level: a realist review to identify implications for programmes in Hong Kong.

PubMed

Lam, Winsome; Dawson, Angela; Fowler, Cathrine

2015-04-01

To identify factors affecting the delivery of health promotion interventions to prevent early childhood human influenza at the household level. Yearly, influenza epidemics seriously affect all age groups, particularly those with weakened immune systems, including children. Influenza is transmitted easily from person to person through droplet and direct contact. Maintaining personal hygiene, avoiding close contact with the infected person and proper hand washing are recommended as the most effective means of preventing the transmission of influenza. However, it is not clear what programme-related mechanisms and contexts are crucial to the successful delivery of interventions in the home. This study systematically reviewed published research studies to identify factors influencing the effective delivery of health promotion programmes targeting influenza in a household. Realist review. A realist review methodology was selected to examine what interventions are effective in preventing and managing influenza at the household level and in what circumstances. A structured search of the peer-reviewed primary research literature was undertaken using a defined search protocol. Eight studies were retrieved for the analysis. Mechanisms impacting on intervention delivery were identified, including timing of implementation, programme reach, organisational and healthcare worker involvement, mode and place of delivery, contact with infected person, health practice compliance and sustainability at home. These findings suggest contextual factors that could be identified through ecological approaches to health promotion that are crucial for policymakers to consider when designing interventions. The active involvement of community nurses through an integrated household visiting programme may help to better deliver family-based health promotion interventions to prevent illnesses such as influenza in children. © 2014 John Wiley & Sons Ltd.

Human T-cell lymphotropic virus type 1-infected T lymphocytes impair catabolism and uptake of glutamate by astrocytes via Tax-1 and tumor necrosis factor alpha.

PubMed

Szymocha, R; Akaoka, H; Dutuit, M; Malcus, C; Didier-Bazes, M; Belin, M F; Giraudon, P

2000-07-01

Human T-cell lymphotropic virus type 1 (HTLV-1) is the causative agent of a chronic progressive myelopathy called tropical spastic paraparesis/HTLV-1-associated myelopathy (TSP/HAM). In this disease, lesions of the central nervous system (CNS) are associated with perivascular infiltration by lymphocytes. We and others have hypothesized that these T lymphocytes infiltrating the CNS may play a prominent role in TSP/HAM. Here, we show that transient contact of human or rat astrocytes with T lymphocytes chronically infected by HTLV-1 impairs some of the major functions of brain astrocytes. Uptake of extracellular glutamate by astrocytes was significantly decreased after transient contact with infected T cells, while the expression of the glial transporters GLAST and GLT-1 was decreased. In two-compartment cultures avoiding direct cell-to-cell contact, similar results were obtained, suggesting possible involvement of soluble factors, such as cytokines and the viral protein Tax-1. Recombinant Tax-1 and tumor necrosis factor alpha (TNF-alpha) decreased glutamate uptake by astrocytes. Tax-1 probably acts by inducing TNF-alpha, as the effect of Tax-1 was abolished by anti-TNF-alpha antibody. The expression of glutamate-catabolizing enzymes in astrocytes was increased for glutamine synthetase and decreased for glutamate dehydrogenase, the magnitudes of these effects being correlated with the level of Tax-1 transcripts. In conclusion, Tax-1 and cytokines produced by HTLV-1-infected T cells impair the ability of astrocytes to manage the steady-state level of glutamate, which in turn may affect neuronal and oligodendrocytic functions and survival.

Laser based spot weld characterization

NASA Astrophysics Data System (ADS)

Jonietz, Florian; Myrach, Philipp; Rethmeier, Michael; Suwala, Hubert; Ziegler, Mathias

2016-02-01

Spot welding is one of the most important joining technologies, especially in the automotive industry. Hitherto, the quality of spot welded joints is tested mainly by random destructive tests. A nondestructive testing technique offers the benefit of cost reduction of the testing procedure and optimization of the fabrication process, because every joint could be examined. This would lead to a reduced number of spot welded joints, as redundancies could be avoided. In the procedure described here, the spot welded joint between two zinc-coated steel sheets (HX340LAD+Z100MB or HC340LA+ZE 50/50) is heated optically on one side. Laser radiation and flash light are used as heat sources. The melted zone, the so called "weld nugget" provides the mechanical stability of the connection, but also constitutes a thermal bridge between the sheets. Due to the better thermal contact, the spot welded joint reveals a thermal behavior different from the surrounding material, where the heat transfer between the two sheets is much lower. The difference in the transient thermal behavior is measured with time resolved thermography. Hence, the size of the thermal contact between the two sheets is determined, which is directly correlated to the size of the weld nugget, indicating the quality of the spot weld. The method performs well in transmission with laser radiation and flash light. With laser radiation, it works even in reflection geometry, thus offering the possibility of testing with just one-sided accessibility. By using heating with collimated laser radiation, not only contact-free, but also remote testing is feasible. A further convenience compared to similar thermographic approaches is the applicability on bare steel sheets without any optical coating for emissivity correction. For this purpose, a proper way of emissivity correction was established.

Who is the Usual Suspect? Evidence of a Selection Bias Toward Faces That Make Direct Eye Contact in a Lineup Task

PubMed Central

van Golde, Celine; Verstraten, Frans A. J.

2017-01-01

The speed and ease with which we recognize the faces of our friends and family members belies the difficulty we have recognizing less familiar individuals. Nonetheless, overconfidence in our ability to recognize faces has carried over into various aspects of our legal system; for instance, eyewitness identification serves a critical role in criminal proceedings. For this reason, understanding the perceptual and psychological processes that underlie false identification is of the utmost importance. Gaze direction is a salient social signal and direct eye contact, in particular, is thought to capture attention. Here, we tested the hypothesis that differences in gaze direction may influence difficult decisions in a lineup context. In a series of experiments, we show that when a group of faces differed in their gaze direction, the faces that were making eye contact with the participants were more likely to be misidentified. Interestingly, this bias disappeared when the faces are presented with their eyes closed. These findings open a critical conversation between social neuroscience and forensic psychology, and imply that direct eye contact may (wrongly) increase the perceived familiarity of a face. PMID:28203355

Development of thin wraparound junction silicon solar cells

NASA Technical Reports Server (NTRS)

Ho, F.; Iles, P. A.

1981-01-01

The state of the art technologies was applied to fabricate 50 micro thick 2x4 cm, coplanar back contact (CBC) solar cells with AMO efficiency above 12%. A requirement was that the cells have low solar absorptance. A wraparound junction (WAJ) with wraparound metallization was chosen. This WAJ approach avoided the need for very complex fixturing, especially during rotation of the cells for providing adequate contacts over dielectric edge layers. The contact adhesion to silicon was considered better than to an insulator. It is indicated that shunt resistance caused by poor WAJ diode quality, and series resistance from the WAJ contact, give good cell performance. The cells developed reached 14 percent AMO efficiency (at 25 C), with solar absorptance values of 0.73. Space/cell environmental tests were performed on these cells and the thin CSC cells performed well. The optimized design configuration and process sequence were used to make 50 deliverable CBC cells. These cells were all above 12 percent efficiency and had an average efficiency of -13 percent. Results of environmental tests (humidity-temperature, thermal shock, and contact adherence) are also given.

Tuberculosis and nutrition: disease perceptions and health seeking behavior of household contacts in the Peruvian Amazon

PubMed Central

Baldwin, M. R.; Yori, P. P.; Ford, C.; Moore, D. A. J.; Gilman, R. H.; Vidal, C.; Ticona, E.; Evans, C. A.

2010-01-01

SETTING Households of TB patients in the Peruvian Amazon. OBJECTIVE To investigate how knowledge and beliefs of household contacts about TB affected health seeking behavior. DESIGN Interviews with 73 patients finishing treatment and 79 of their adult household contacts. RESULTS Contacts were knowledgeable about free screening and treatment, but contacts who noted weight loss, not cough, were more likely to be screened for TB (P = 0.03). Forty-two per cent reported that TB was prevented by nutrition, 28% by separating eating utensils, and only 19% by avoiding a coughing patient. Only one household contact reported being stigmatized. Stigma centered upon nutrition, and only 12% knew of the association between TB and HIV. Only 14% had a BMI <20, yet 30% reported regularly going to sleep hungry. Free food packages were reported to be the most important reason for treatment adherence by 33% of patients. CONCLUSION Contacts misperceived TB as a nutritional disease and did not fear airborne transmission, which should be corrected by public health education. Weight loss, and not cough, led to screening. Stigma appeared to be minimized because risk was perceived as personal, through malnutrition, rather than exposure-based. Nutritional incentives that utilize these beliefs may reduce diagnostic delay and enhance treatment adherence. PMID:15636496

Effects of tooth root contact on the stability of orthodontic anchor screws in the maxilla: Comparison between self-drilling and self-tapping methods.

PubMed

Iwai, Hiroaki; Motoyoshi, Mitsuru; Uchida, Yasuki; Matsuoka, Miho; Shimizu, Noriyoshi

2015-04-01

We evaluated the effects of screw placement angle on the frequency of root contact and the effects of root contact on screw stability, comparing self-drilling and self-tapping methods. In total, 80 patients with 142 screws (diameter, 1.6 mm; length, 8.0 mm) were included. Cone-beam computed tomography images were taken. Cortical bone thickness, interroot distance, shortest distance between the screw and adjacent tooth root, and screw placement angle were measured. The success rates of the screws were 91.5% for the self-drilling method and 94.4% for the self-tapping method (P >0.05). The self-drilling screws tended to contact the distal tooth roots in the right maxilla. In the self-drilling method, the failure rate was significantly higher in the root contact group than in the no-contact group (P <0.05). The success rate was not significantly different between the self-drilling and the self-tapping methods in the maxilla. Avoidance of tooth root contact may improve the success rate more in the self-drilling method than in the self-tapping method. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Laser-fired contact formation on metallized and passivated silicon wafers under short pulse durations

NASA Astrophysics Data System (ADS)

Raghavan, Ashwin S.

The objective of this work is to develop a comprehensive understanding of the physical processes governing laser-fired contact (LFC) formation under microsecond pulse durations. Primary emphasis is placed on understanding how processing parameters influence contact morphology, passivation layer quality, alloying of Al and Si, and contact resistance. In addition, the research seeks to develop a quantitative method to accurately predict the contact geometry, thermal cycles, heat and mass transfer phenomena, and the influence of contact pitch distance on substrate temperatures in order to improve the physical understanding of the underlying processes. Finally, the work seeks to predict how geometry for LFCs produced with microsecond pulses will influence fabrication and performance factors, such as the rear side contacting scheme, rear surface series resistance and effective rear surface recombination rates. The characterization of LFC cross-sections reveals that the use of microsecond pulse durations results in the formation of three-dimensional hemispherical or half-ellipsoidal contact geometries. The LFC is heavily alloyed with Al and Si and is composed of a two-phase Al-Si microstructure that grows from the Si wafer during resolidification. As a result of forming a large three-dimensional contact geometry, the total contact resistance is governed by the interfacial contact area between the LFC and the wafer rather than the planar contact area at the original Al-Si interface within an opening in the passivation layer. By forming three-dimensional LFCs, the total contact resistance is significantly reduced in comparison to that predicted for planar contacts. In addition, despite the high energy densities associated with microsecond pulse durations, the passivation layer is well preserved outside of the immediate contact region. Therefore, the use of microsecond pulse durations can be used to improve device performance by leading to lower total contact resistances while preserving the passivation layer. A mathematical model was developed to accurately predict LFC geometry over a wide range of processing parameters by accounting for transient changes in Al and Si alloy composition within the LFC. Since LFC geometry plays a critical role in device performance, an accurate method to predict contact geometry is an important tool that can facilitate further process development. Dimensionless analysis was also conducted to evaluate the relative importance of heat and mass transfer mechanisms. It is shown that convection plays a dominant role in the heat and mass transfer within the molten pool. Due to convective mass transfer, the contacts are heavily doped with Al and Si within 10 is after contact formation, which contributes to the entire resolidified region behaving as the electrically active LFC. The validated model is also used to determine safe operating regimes during laser processing to avoid excessively high operating temperatures. By maintaining processing temperatures below a critical temperature threshold, the onset of liquid metal expulsion and loss of alloying elements can be avoided. The process maps provide a framework that can be used to tailor LFC geometry for device fabrication. Finally, using various geometric relationships for the rear side contacting scheme for photovoltaic devices, it is shown that by employing hemispherical contacts, the number of LFCs required on the rear side can be reduced 75% while doubling the pitch distance and increasing the passivation fraction. Reducing the number of backside contacts required can have a noteworthy impact of manufacturing throughput. In addition, the analytical models suggest that device performance can be maintained at levels comparable to those achieved for planar contacts when producing three-dimensional contacts. The materials and electrical characterization results, device simulations, and design considerations presented in this thesis indicate that by forming three-dimensional LFCs, performance levels of Si-based photovoltaic devices can be maintained while greatly enhancing manufacturing efficiency. The research lays a solid foundation for future development of the LFC process with microsecond pulse durations and indicates that device fabrication employing this method is a critical step moving forward.

Individual Differences in the Relationship Between Attachment and Nomophobia Among College Students: The Mediating Role of Mindfulness

PubMed Central

Arpaci, Ibrahim; Özteke Kozan, Hatice İrem; Kesici, Şahin

2017-01-01

Background There is a growing interest in nomophobia, which is defined as the fear of being out of cellular phone contact, or "feelings of discomfort or anxiety experienced by individuals when they are unable to use their mobile phones or utilize the affordances these devices provide”. However, only limited research can be found in terms of its determinants at present. Contemporary literature suggests that the relationships among attachment styles, mindfulness, and nomophobia have not been investigated. Objective This study aims to investigate the mediating effect of mindfulness on the relationship between attachment and nomophobia. In addition, the study also focuses on gender differences in attachment, mindfulness, and nomophobia. A theory-based structural model was tested to understand the essentials of the associations between the constructs. Methods The Experiences in Close Relationships Scale, Nomophobia Questionnaire, and Mindful Attention Awareness Scale were used to collect data from undergraduate students (N=450; 70.9% women [319/450]; mean age=21.94 years [SD 3.61]). Two measurement models (ie, attachment and mindfulness) and a structural model were specified, estimated, and evaluated. Results The structural equation model shows that the positive direct effects of avoidant (.13, P=.03) and anxious attachment (.48, P<.001) on nomophobia were significant. The negative direct effects of avoidant (−.18, P=.01) and anxious attachment (−.33, P<.001) on mindfulness were also significant. Moreover, mindfulness has a significant negative effect on nomophobia for women only (−.13, P=.03). Finally, the Sobel test showed that the indirect effects of avoidant and anxious attachment on nomophobia via mindfulness were significant (P<.001). The direct and indirect effects of anxious attachment, avoidant attachment, and mindfulness altogether accounted for 33% of the total variance in nomophobia. Gender comparison results show that there is a significant difference in attachment based on gender (F2,447=6.97, P=.01, Wilk λ=.97, partial η2=.03). Women (mean 68.46 [SD 16.96]) scored significantly higher than men (mean 63.59 [SD 15.97]) in anxious attachment (F1=7.93, P=.01, partial η2=.02). Gender differences in mindfulness were not significant (F4,448=3.45, P=.69). On the other hand, results do show significant gender differences in nomophobia (F4,445=2.71, P=.03, Wilk λ=.98, partial η2=.02) where women scored significantly higher than men. Conclusions In general, individuals who are emotionally more dependent and crave more closeness and attention in the relationship tend to display higher levels of fear or discomfort when they have no access to their mobile phones. However, gender has a differential impact on the relationship between avoidant attachment and nomophobia. This study establishes the impact of mindfulness on nomophobia for women; therefore, future studies should test the effectiveness of mindfulness-based therapy approaches and confirm whether they are effective and efficient. On the basis of significant gender difference in nomophobia and attachment, we conclude that gender should be taken into account in mindfulness-based treatments dealing with nomophobia. PMID:29242179

Shy Children Are Less Sensitive to Some Cues to Facial Recognition

ERIC Educational Resources Information Center

Brunet, Paul M.; Mondloch, Catherine J.; Schmidt, Louis A.

2010-01-01

Temperamental shyness in children is characterized by avoidance of faces and eye contact, beginning in infancy. We conducted two studies to determine whether temperamental shyness was associated with deficits in sensitivity to some cues to facial identity. In Study 1, 40 typically developing 10-year-old children made same/different judgments about…

Corrosion avoidance with new wood preservatives

Treesearch

Samuel L. Zelinka; Douglas R. Rammer

2007-01-01

This article focuses on considerations that need to be made when choosing products, other than stainless steel, to minimize corrosion of metals in contact with treated wood. With so many ?corrosion-resistant? alternative products on the market, it is important to know the fundamental principles of corrosion protection to make informed decisions when designing...

Writing for the Ear: Strengthening Oral Style in Manuscript Speeches

ERIC Educational Resources Information Center

Bruss, Kristine

2012-01-01

Public speaking texts typically advise speakers to avoid using a manuscript. Speaking from a manuscript can limit eye contact, reduce expressiveness, and bore listeners. The ideal, rather, is to sound conversational. Conversational style is inclusive, suggesting that a speaker is ""of the people," united in understanding, values and purpose." If a…

Epitaxially grown collagen fibrils reveal diversity in contact guidance behavior among cancer cells.

PubMed

Wang, Juan; Petefish, Joseph W; Hillier, Andrew C; Schneider, Ian C

2015-01-01

Invasion of cancer cells into the surrounding tissue is an important step during cancer progression and is driven by cell migration. Cell migration can be random, but often it is directed by various cues such as aligned fibers composed of extracellular matrix (ECM), a process called contact guidance. During contact guidance, aligned fibers bias migration along the long axis of the fibers. These aligned fibers of ECM are commonly composed of type I collagen, an abundant structural protein around tumors. In this paper, we epitaxially grew several different patterns of organized type I collagen on mica and compared the morphology and contact guidance behavior of two invasive breast cancer cell lines (MDA-MB-231 and MTLn3 cells). Others have shown that these cells randomly migrate in qualitatively different ways. MDA-MB-231 cells exert large traction forces, tightly adhere to the ECM, and migrate with spindle-shaped morphology and thus adopt a mesenchymal mode of migration. MTLn3 cells exert small traction forces, loosely adhere to the ECM, and migrate with a more rounded morphology and thus adopt an amoeboid mode of migration. As the degree of alignment of type I collagen fibrils increases, cells become more elongated and engage in more directed contact guidance. MDA-MB-231 cells perceive the directional signal of highly aligned type I collagen fibrils with high fidelity, elongating to large extents and migrating directionally. Interestingly, behavior in MTLn3 cells differs. While highly aligned type I collagen fibril patterns facilitate spreading and random migration of MTLn3 cells, they do not support elongation or directed migration. Thus, different contact guidance cues bias cell migration differently and the fidelity of contact guidance is cell type dependent, suggesting that ECM alignment is a permissive cue for contact guidance, but requires a cell to have certain properties to interpret that cue.

A Bio-inspired Collision Avoidance Model Based on Spatial Information Derived from Motion Detectors Leads to Common Routes

PubMed Central

Bertrand, Olivier J. N.; Lindemann, Jens P.; Egelhaaf, Martin

2015-01-01

Avoiding collisions is one of the most basic needs of any mobile agent, both biological and technical, when searching around or aiming toward a goal. We propose a model of collision avoidance inspired by behavioral experiments on insects and by properties of optic flow on a spherical eye experienced during translation, and test the interaction of this model with goal-driven behavior. Insects, such as flies and bees, actively separate the rotational and translational optic flow components via behavior, i.e. by employing a saccadic strategy of flight and gaze control. Optic flow experienced during translation, i.e. during intersaccadic phases, contains information on the depth-structure of the environment, but this information is entangled with that on self-motion. Here, we propose a simple model to extract the depth structure from translational optic flow by using local properties of a spherical eye. On this basis, a motion direction of the agent is computed that ensures collision avoidance. Flying insects are thought to measure optic flow by correlation-type elementary motion detectors. Their responses depend, in addition to velocity, on the texture and contrast of objects and, thus, do not measure the velocity of objects veridically. Therefore, we initially used geometrically determined optic flow as input to a collision avoidance algorithm to show that depth information inferred from optic flow is sufficient to account for collision avoidance under closed-loop conditions. Then, the collision avoidance algorithm was tested with bio-inspired correlation-type elementary motion detectors in its input. Even then, the algorithm led successfully to collision avoidance and, in addition, replicated the characteristics of collision avoidance behavior of insects. Finally, the collision avoidance algorithm was combined with a goal direction and tested in cluttered environments. The simulated agent then showed goal-directed behavior reminiscent of components of the navigation behavior of insects. PMID:26583771

Visual feedback training improves postural adjustments associated with moving obstacle avoidance in elderly women.

PubMed

Hatzitaki, V; Voudouris, D; Nikodelis, T; Amiridis, I G

2009-02-01

The study examined the impact of visually guided weight shifting (WS) practice on the postural adjustments evoked by elderly women when avoiding collision with a moving obstacle while standing. Fifty-six healthy elderly women (70.9+/-5.7 years, 87.5+/-9.6 kg) were randomly assigned into one of three groups: a group that completed 12 sessions (25 min, 3s/week) of WS practice in the Anterior/Posterior direction (A/P group, n=20), a group that performed the same practice in the medio/lateral direction (M/L group, n=20) and a control group (n=16). Pre- and post-training, participants were tested in a moving obstacle avoidance task. As a result of practice, postural response onset shifted closer to the time of collision with the obstacle. Side-to-side WS resulted in a reduction of the M/L sway amplitude and an increase of the trunk's velocity during avoidance. It is concluded that visually guided WS practice enhances elderly's ability for on-line visuo-motor processing when avoiding collision eliminating reliance on anticipatory scaling. Specifying the direction of WS seems to be critical for optimizing the transfer of training adaptations.

Clinical measurement of the height of the interproximal contact area in maxillary anterior teeth.

PubMed

Sghaireen, Mohd G; Al-Zarea, Bader K; Al-Shorman, Hisham M; Al-Omiri, Mahmoud K

2013-11-01

To clinically quantify the apicoincisal height of interproximal areas directly in patients' mouths. Thirty participants (11 females and 9 males, mean age=26±1.5 years) were recruited into this study. Measurement of interproximal contact areas was carried out directly in patients' mouths using digital caliper (TERENSA, USA) with measuring accuracy of 0.01 mm. The interproximal contact areas that were measured are: central incisor to central incisor, central incisor to lateral incisor, lateral incisor to canine, and canine to first premolar on both sides of the jaw. Statistical significance was based on probability values less than 0.05 (p<0.05). The largest contact point was the one present between central incisors and it ranged from 2.9 to 6.5 mm. On the other hand, the contact point between canine and first premolar was the smallest on both sides of the arch and ranged from 0.6 to 2.5 mm. The dimensions of the contact points declined as we move from anterior area backwards. Statistical analysis using t-test showed that there were significant differences between the measurements of interproximal points of each tooth (P<0.05). the apicogingival dimension of the contact point decreased as we moved from anterior to posterior teeth. The contact area between the central incisors was largest and the one between canine and premolar was the smallest. This study is the first to report direct intra-oral clinical measurement of contact points. Clinical evaluation of contact point dimensions using digital caliber is a viable, quick and accurate method to use.

Light transfer through windows with external condensation

NASA Astrophysics Data System (ADS)

Zhu, Keyong; Li, Shaoling; Pilon, Laurent

2018-03-01

This study investigates systematically light transfer through windows supporting cap-shaped droplets on their external face. The presence of such droplets may have negative effects on the conversion efficiency of solar cells, distorts image quality of lenses, or hinders visibility through windows and windshields. Here, the directional-hemispherical transmittance was predicted by the Monte Carlo ray-tracing method. The droplets were monodisperse or polydisperse randomly distributed on the outside face of optically smooth windows. For nonabsorbing droplets, the diameter and size distribution did not have a significant effect on the window directional-hemispherical transmittance. The latter was nearly independent of contact angle for incident angle θi ≤ 30°. However, the directional-hemispherical transmittance decreased monotonously with increasing incident angle and droplet contact angle for contact angle θc ≤ 70° to reach a minimum at a contact angle θc,min beyond which it increased with increasing contact angle before reaching a plateau at large contact angles. This was attributed to total internal reflection at the back window/air and droplet/air interfaces. For absorbing droplets, the normal-hemispherical transmittance decreased significantly with increasing droplet contact angle, mean diameter, polydispersity, and projected surface area coverage due to strong absorption within the droplets. Moreover, the normal-hemispherical transmittance decreased with increasing contact angle for θc< 90° and remained constant and independent of the droplets' absorption index, mean diameter, and contact angle for θc ≥ 90°. Finally, Analytical expressions for the upper and lower bounds of the normal-hemispherical transmittance as a function of droplet contact angle, optical properties, and projected surface area coverage were derived.

Formation of retinal direction-selective circuitry initiated by starburst amacrine cell homotypic contact

PubMed Central

Ray, Thomas A; Roy, Suva; Kozlowski, Christopher; Wang, Jingjing; Cafaro, Jon; Hulbert, Samuel W; Wright, Christopher V; Field, Greg D

2018-01-01

A common strategy by which developing neurons locate their synaptic partners is through projections to circuit-specific neuropil sublayers. Once established, sublayers serve as a substrate for selective synapse formation, but how sublayers arise during neurodevelopment remains unknown. Here, we identify the earliest events that initiate formation of the direction-selective circuit in the inner plexiform layer of mouse retina. We demonstrate that radially migrating newborn starburst amacrine cells establish homotypic contacts on arrival at the inner retina. These contacts, mediated by the cell-surface protein MEGF10, trigger neuropil innervation resulting in generation of two sublayers comprising starburst-cell dendrites. This dendritic scaffold then recruits projections from circuit partners. Abolishing MEGF10-mediated contacts profoundly delays and ultimately disrupts sublayer formation, leading to broader direction tuning and weaker direction-selectivity in retinal ganglion cells. Our findings reveal a mechanism by which differentiating neurons transition from migratory to mature morphology, and highlight this mechanism’s importance in forming circuit-specific sublayers. PMID:29611808

Using the Subtle Avoidance Frequency Examination in Adolescent Social Anxiety Assessments

ERIC Educational Resources Information Center

Thomas, Sarah A.; Daruwala, Samantha E.; Goepel, Katherine A.; De Los Reyes, Andres

2012-01-01

Background: Individuals with social anxiety use safety behaviors to directly or indirectly avoid social situations (e.g., remaining quiet in a social setting to avoid saying anything embarrassing). Safety behaviors have been hypothesized to prevent the disconfirmation of feared occurrences while in social situations. Further, research indicates…

Intraoral versus extraoral measurement of the height of the interproximal contact area in maxillary anterior teeth.

PubMed

Sghaireen, Mohd G; Albhiran, Heyam Mobark; Alzoubi, Ibrahim A; Lynch, Edward; Al-Omiri, Mahmoud K

2015-01-01

This study aimed to clinically quantify the apicoincisal height of the upper interproximal areas directly in patients' mouths compared to measurements on stone models. One hundred and fifty participants (75 females and 75 males, age range 20-45 years) were recruited for this study. A digital caliper was used to measure the anterior maxillary interproximal contact areas directly in patients' mouths and on stone models. The digital caliper accuracy was up to 0.01. The Statistical Package for Social Sciences software (SPSS, version 19.0, Chicago, Ill., USA) was used for statistical analysis. Statistical significance was based on probability values <0.05. The intraoral measurement of proximal contacts as well as the measurement on stone models showed that the dimensions of interproximal contacts on both sides of each tooth were significantly different (p < 0.001) and that the dimension of the mesial contact point was larger than that of the distal contact point of each tooth. The largest contact point was the one between the central incisors (direct intraoral measurement = 2.9-6.49 mm; model measurement = 3.31-6.91 mm). On the other hand, the contact point between the canine and first premolar was the smallest on both sides of the arch (0.63-2.52 mm intraorally, 0.98-2.88 mm on models). The intraoral measurement of contact points was more accurate than model measurements, and the differences were statistically significant (p < 0.001). The clinical evaluation of contact point dimensions using a digital caliper was more precise than measuring contact points on stone models; hence, it is a viable, quick and adequate method to be used routinely. © 2015 S. Karger AG, Basel.

Knee medial and lateral contact forces in a musculoskeletal model with subject-specific contact point trajectories.

PubMed

Zeighami, A; Aissaoui, R; Dumas, R

2018-03-01

Contact point (CP) trajectory is a crucial parameter in estimating medial/lateral tibio-femoral contact forces from the musculoskeletal (MSK) models. The objective of the present study was to develop a method to incorporate the subject-specific CP trajectories into the MSK model. Ten healthy subjects performed 45 s treadmill gait trials. The subject-specific CP trajectories were constructed on the tibia and femur as a function of extension-flexion using low-dose bi-plane X-ray images during a quasi-static squat. At each extension-flexion position, the tibia and femur CPs were superimposed in the three directions on the medial side, and in the anterior-posterior and proximal-distal directions on the lateral side to form the five kinematic constraints of the knee joint. The Lagrange multipliers associated to these constraints directly yielded the medial/lateral contact forces. The results from the personalized CP trajectory model were compared against the linear CP trajectory and sphere-on-plane CP trajectory models which were adapted from the commonly used MSK models. Changing the CP trajectory had a remarkable impact on the knee kinematics and changed the medial and lateral contact forces by 1.03 BW and 0.65 BW respectively, in certain subjects. The direction and magnitude of the medial/lateral contact force were highly variable among the subjects and the medial-lateral shift of the CPs alone could not determine the increase/decrease pattern of the contact forces. The suggested kinematic constraints are adaptable to the CP trajectories derived from a variety of joint models and those experimentally measured from the 3D imaging techniques. Copyright © 2018 Elsevier Ltd. All rights reserved.

Length scale selects directionality of droplets on vibrating pillar ratchet

DOE PAGES

Agapov, Rebecca L.; Boreyko, Jonathan B.; Briggs, Dayrl P.; ...

2014-09-22

Directional control of droplet motion at room temperature is of interest for applications such as microfluidic devices, self-cleaning coatings, and directional adhesives. Here, arrays of tilted pillars ranging in height from the nanoscale to the microscale are used as structural ratchets to directionally transport water at room temperature. Water droplets deposited on vibrating chips with a nanostructured ratchet move preferentially in the direction of the feature tilt while the opposite directionality is observed in the case of microstructured ratchets. This remarkable switch in directionality is consistent with changes in the contact angle hysteresis. To glean further insights into the lengthmore » scale dependent asymmetric contact angle hysteresis, the contact lines formed by a nonvolatile room temperature ionic liquid placed onto the tilted pillar arrays were visualized and analyzed in situ in a scanning electron microscope. As a result, the ability to tune droplet directionality by merely changing the length scale of surface features all etched at the same tilt angle would be a versatile tool for manipulating multiphase flows and for selecting droplet directionality in other lap-on-chip applications.« less

An observational study of socioeconomic and clinical gradients among diabetes patients hospitalized for avoidable causes: evidence of underlying health disparities in China?

PubMed

Chen, Brian; Eggleston, Karen; Li, Hong; Shah, Nilay; Wang, Jian

2014-01-30

Diabetes is an ambulatory care sensitive condition that can generally be managed in outpatient settings with little or no need for inpatient care. As a preliminary step to investigate whether health disparities can be detected in the inpatient setting in China, we study how diabetic patients hospitalized without prior primary care contact or with greater severity of illness differ from other diabetic inpatients along socioeconomic and clinical dimensions. We conduct an observational study using three years of clinical data for more than 1,800 adult patients with diabetes at two tertiary hospitals in East China. Univariate analysis and probit regression are used to characterize the differences in socioeconomic and clinical factors between patients hospitalized for diabetes with no prior primary care contact and those hospitalized with previous treatment experience. Secondarily, we use ordinary least squares regression to estimate the socioeconomic and clinical differences associated with poor serum glucose control at admission. We find that compared with patients hospitalized after prior treatment experience, inpatients with no previous primary care contact for diabetes have worse clinical laboratory values, are more likely to be young and male, to have lower education attainment, and to have poorer blood sugar control. Insurance, urban residence, and previous use of diabetic medication are in turn negatively correlated with HbA1c levels upon admission. Among hospitalized diabetic patients, socioeconomic factors such as lower education attainment, rural residence and lack of full insurance are associated with avoidable hospitalizations or worse indicators of health. Although we cannot definitively rule out selection bias, these findings are consistent with health disparities observable even at the inpatient level. Future studies should study the underlying mechanism by which traditionally vulnerable groups are more likely to be hospitalized for avoidable causes and with greater severity of illness.

Stokes flow inside an evaporating liquid line for any contact angle

NASA Astrophysics Data System (ADS)

Petsi, A. J.; Burganos, V. N.

2008-09-01

Evaporation of droplets or liquid films lying on a substrate induces internal viscous flow, which affects the transport of suspended particles and, thus, the final deposit profile in numerous applications. In this work, the problem of Stokes flow inside a two-dimensional droplet, representing the cross section of an evaporating liquid line lying on a flat surface, is considered. The stream function formulation is adopted, leading to the biharmonic equation in bipolar coordinates. A solution in closed form is obtained for any contact angle in (0,π) and is, thus, valid for both hydrophilic and hydrophobic substrates. The solution can be used with any type of evaporation mechanism, including diffusion, convection, or kinetically controlled modes. Both pinned and depinned contact lines are considered. For the boundary conditions to be compatible at the contact lines, the Navier slip boundary condition is applied on the substrate. Numerical results are presented for kinetically and diffusion controlled evaporation. For pinned contact lines, the flow inside the evaporating liquid line is directed towards the edges, thus, promoting the coffee stain phenomenon. In the case of depinned contact lines and contact angle less than π/2 , the flow is directed towards the center of the droplet, whereas, for strongly hydrophobic substrates it is directed outwards.

Automated guidance algorithms for a space station-based crew escape vehicle.

PubMed

Flanary, R; Hammen, D G; Ito, D; Rabalais, B W; Rishikof, B H; Siebold, K H

2003-04-01

An escape vehicle was designed to provide an emergency evacuation for crew members living on a space station. For maximum escape capability, the escape vehicle needs to have the ability to safely evacuate a station in a contingency scenario such as an uncontrolled (e.g., tumbling) station. This emergency escape sequence will typically be divided into three events: The first separation event (SEP1), the navigation reconstruction event, and the second separation event (SEP2). SEP1 is responsible for taking the spacecraft from its docking port to a distance greater than the maximum radius of the rotating station. The navigation reconstruction event takes place prior to the SEP2 event and establishes the orbital state to within the tolerance limits necessary for SEP2. The SEP2 event calculates and performs an avoidance burn to prevent station recontact during the next several orbits. This paper presents the tools and results for the whole separation sequence with an emphasis on the two separation events. The first challenge includes collision avoidance during the escape sequence while the station is in an uncontrolled rotational state, with rotation rates of up to 2 degrees per second. The task of avoiding a collision may require the use of the Vehicle's de-orbit propulsion system for maximum thrust and minimum dwell time within the vicinity of the station vicinity. The thrust of the propulsion system is in a single direction, and can be controlled only by the attitude of the spacecraft. Escape algorithms based on a look-up table or analytical guidance can be implemented since the rotation rate and the angular momentum vector can be sensed onboard and a-priori knowledge of the position and relative orientation are available. In addition, crew intervention has been provided for in the event of unforeseen obstacles in the escape path. The purpose of the SEP2 burn is to avoid re-contact with the station over an extended period of time. Performing this maneuver requires knowledge of the orbital state, which is obtained during the navigation state reconstruction event. Since the direction of the delta-v of the SEP1 maneuver is a random variable with respect to the Local Vertical Local Horizontal (LVLH) coordinate system, calculating the required SEP2 burn is a challenge. This problem was solved using elements of neural network theory for model-free function approximation and decision making. c2003 COSPAR. Published by Elsevier Science Ltd. All rights reserved.

21 CFR 886.5925 - Soft (hydrophilic) contact lens.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Soft (hydrophilic) contact lens. 886.5925 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5925 Soft (hydrophilic) contact lens. (a) Identification. A soft (hydrophilic) contact lens is a device intended to be worn directly...

21 CFR 886.5925 - Soft (hydrophilic) contact lens.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Soft (hydrophilic) contact lens. 886.5925 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5925 Soft (hydrophilic) contact lens. (a) Identification. A soft (hydrophilic) contact lens is a device intended to be worn directly...

Refrigerant directly cooled capacitors

DOEpatents

Hsu, John S [Oak Ridge, TN; Seiber, Larry E [Oak Ridge, TN; Marlino, Laura D [Oak Ridge, TN; Ayers, Curtis W [Kingston, TN

2007-09-11

The invention is a direct contact refrigerant cooling system using a refrigerant floating loop having a refrigerant and refrigeration devices. The cooling system has at least one hermetic container disposed in the refrigerant floating loop. The hermetic container has at least one electronic component selected from the group consisting of capacitors, power electronic switches and gating signal module. The refrigerant is in direct contact with the electronic component.

Automatic Classification of Protein Structure Using the Maximum Contact Map Overlap Metric

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andonov, Rumen; Djidjev, Hristo Nikolov; Klau, Gunnar W.

In this paper, we propose a new distance measure for comparing two protein structures based on their contact map representations. We show that our novel measure, which we refer to as the maximum contact map overlap (max-CMO) metric, satisfies all properties of a metric on the space of protein representations. Having a metric in that space allows one to avoid pairwise comparisons on the entire database and, thus, to significantly accelerate exploring the protein space compared to no-metric spaces. We show on a gold standard superfamily classification benchmark set of 6759 proteins that our exact k-nearest neighbor (k-NN) scheme classifiesmore » up to 224 out of 236 queries correctly and on a larger, extended version of the benchmark with 60; 850 additional structures, up to 1361 out of 1369 queries. Finally, our k-NN classification thus provides a promising approach for the automatic classification of protein structures based on flexible contact map overlap alignments.« less

Automatic Classification of Protein Structure Using the Maximum Contact Map Overlap Metric

DOE PAGES

Andonov, Rumen; Djidjev, Hristo Nikolov; Klau, Gunnar W.; ...

2015-10-09

In this paper, we propose a new distance measure for comparing two protein structures based on their contact map representations. We show that our novel measure, which we refer to as the maximum contact map overlap (max-CMO) metric, satisfies all properties of a metric on the space of protein representations. Having a metric in that space allows one to avoid pairwise comparisons on the entire database and, thus, to significantly accelerate exploring the protein space compared to no-metric spaces. We show on a gold standard superfamily classification benchmark set of 6759 proteins that our exact k-nearest neighbor (k-NN) scheme classifiesmore » up to 224 out of 236 queries correctly and on a larger, extended version of the benchmark with 60; 850 additional structures, up to 1361 out of 1369 queries. Finally, our k-NN classification thus provides a promising approach for the automatic classification of protein structures based on flexible contact map overlap alignments.« less

An Optimized Centrifugal Method for Separation of Semen from Superabsorbent Polymers for Forensic Analysis.

PubMed

Camarena, Lucy R; Glasscock, Bailey K; Daniels, Demi; Ackley, Nicolle; Sciarretta, Marybeth; Seashols-Williams, Sarah J

2017-03-01

Connection of a perpetrator to a sexual assault is best performed through the confirmed presence of semen, thereby proving sexual contact. Evidentiary items can include sanitary napkins or diapers containing superabsorbent polymers (SAPs), complicating spermatozoa visualization and DNA analysis. In this report, we evaluated the impact of SAPS on the current forensic DNA workflow, developing an efficient centrifugal protocol for separating spermatozoa from SAP material. The optimized filtration method was compared to common practices of excising the top layer only, resulting in significantly higher sperm yields when a core sample of the substrate was taken. Direct isolation of the SAP-containing materials without filtering resulted in 20% sample failure; additionally, SAP material was observed in the final eluted DNA samples, causing physical interference. Thus, use of the described centrifugal-filtering method is a simple preliminary step that improves spermatozoa visualization and enables more consistent DNA yields, while also avoiding SAP interference. © 2016 American Academy of Forensic Sciences.

Photonic crystal fiber temperature sensor with high sensitivity based on surface plasmon resonance

NASA Astrophysics Data System (ADS)

Wu, Junjun; Li, Shuguang; shi, Min; Feng, Xinxing

2018-07-01

A high sensitivity photonic crystal fiber (PCF) temperature sensor based on surface plasmon resonance is proposed and evaluated using the finite element method. Besides, the coupling phenomenon is studied. The gold layer deposited on the polishing surface of D-shape PCF is used as the metal to stimulate surface plasma, which can improves the sensitivity. Through exquisite design, the birefringence of the fiber is improved, which makes the loss of y-polarization far greater than the loss of x-polarization. The D-shape fiber avoids filling metal and liquid into the air-holes, which can contact with fluid directly to feel temperature. When the phase matching condition is satisfied, the core mode will couple with the surface plasma mode. The resonance position of y-polarization is very sensitive to the temperature change. The simulation shows that the PCF has high sensitivity of 36.86 nm/°C in y-polarization and wide detection that from 10 °C to 85 °C.

New connectors coming for enteral feeding tubes; marqibo and risk of errors; angeliq is not a birth control pill.

PubMed

Cohen, Michael R; Smetzer, Judy L

2014-07-01

These medication errors have occurred in health care facilities at least once. They will happen again-perhaps where you work. Through education and alertness of personnel and procedural safeguards, they can be avoided. You should consider publishing accounts of errors in your newsletters and/or presenting them at your inservice training programs. Your assistance is required to continue this feature. The reports described here were received through the Institute for Safe Medication Practices (ISMP) Medication Errors Reporting Program. Any reports published by ISMP will be anonymous. Comments are also invited; the writers' names will be published if desired. ISMP may be contacted at the address shown below. Errors, close calls, or hazardous conditions may be reported directly to ISMP through the ISMP Web site (www.ismp.org), by calling 800-FAIL-SAFE, or via e-mail at ismpinfo@ismp.org. ISMP guarantees the confidentiality and security of the information received and respects reporters' wishes as to the level of detail included in publications.

Atomic layer deposited oxide films as protective interface layers for integrated graphene transfer

NASA Astrophysics Data System (ADS)

Cabrero-Vilatela, A.; Alexander-Webber, J. A.; Sagade, A. A.; Aria, A. I.; Braeuninger-Weimer, P.; Martin, M.-B.; Weatherup, R. S.; Hofmann, S.

2017-12-01

The transfer of chemical vapour deposited graphene from its parent growth catalyst has become a bottleneck for many of its emerging applications. The sacrificial polymer layers that are typically deposited onto graphene for mechanical support during transfer are challenging to remove completely and hence leave graphene and subsequent device interfaces contaminated. Here, we report on the use of atomic layer deposited (ALD) oxide films as protective interface and support layers during graphene transfer. The method avoids any direct contact of the graphene with polymers and through the use of thicker ALD layers (≥100 nm), polymers can be eliminated from the transfer-process altogether. The ALD film can be kept as a functional device layer, facilitating integrated device manufacturing. We demonstrate back-gated field effect devices based on single-layer graphene transferred with a protective Al2O3 film onto SiO2 that show significantly reduced charge trap and residual carrier densities. We critically discuss the advantages and challenges of processing graphene/ALD bilayer structures.

ISMP Medication Error Report Analysis

PubMed Central

Cohen, Michael R.; Smetzer, Judy L.

2017-01-01

These medication errors have occurred in health care facilities at least once. They will happen again—perhaps where you work. Through education and alertness of personnel and procedural safeguards, they can be avoided. You should consider publishing accounts of errors in your newsletters and/or presenting them at your inservice training programs. Your assistance is required to continue this feature. The reports described here were received through the Institute for Safe Medication Practices (ISMP) Medication Errors Reporting Program. Any reports published by ISMP will be anonymous. Comments are also invited; the writers' names will be published if desired. ISMP may be contacted at the address shown below. Errors, close calls, or hazardous conditions may be reported directly to ISMP through the ISMP Web site (www.ismp.org), by calling 800-FAIL-SAFE, or via e-mail at ismpinfo@ismp.org. ISMP guarantees the confidentiality and security of the information received and respects reporters' wishes as to the level of detail included in publications. PMID:28179735

ISMP Medication Error Report Analysis

PubMed Central

Cohen, Michael R.; Smetzer, Judy L.

2017-01-01

These medication errors have occurred in health care facilities at least once. They will happen again—perhaps where you work. Through education and alertness of personnel and procedural safeguards, they can be avoided. You should consider publishing accounts of errors in your newsletters and/or presenting them at your in-service training programs. Your assistance is required to continue this feature. The reports described here were received through the Institute for Safe Medication Practices (ISMP) Medication Errors Reporting Program. Any reports published by ISMP will be anonymous. Comments are also invited; the writers’ names will be published if desired. ISMP may be contacted at the address shown below. Errors, close calls, or hazardous conditions may be reported directly to ISMP through the ISMP Web site (www.ismp.org), by calling 800-FAIL-SAFE, or via e-mail at ismpinfo@ismp.org. ISMP guarantees the confidentiality and security of the information received and respects reporters’ wishes as to the level of detail included in publications. PMID:29276260

Record Efficiency on Large Area P-Type Czochralski Silicon Substrates

NASA Astrophysics Data System (ADS)

Hallam, Brett; Wenham, Stuart; Lee, Haeseok; Lee, Eunjoo; Lee, Hyunwoo; Kim, Jisun; Shin, Jeongeun; Cho, Kyeongyeon; Kim, Jisoo

2012-10-01

In this work we report a world record independently confirmed efficiency of 19.4% for a large area p-type Czochralski grown solar cell fabricated with a full area aluminium back surface field. This is achieved using the laser doped selective emitter solar cell technology on an industrial screen print production line with the addition of laser doping and light induced plating equipment. The use of a modified diffusion process is explored in which the emitter is diffused to a sheet resistance of 90 Ω/square and subsequent etch back of the emitter to 120 Ω/square. This results in a lower surface concentration of phosphorus compared to that of emitters diffused directly to 120 Ω/square. This modified diffusion process subsequently reduces the conductivity of the surface in relation to that of the heavily diffused laser doped contacts and avoids parasitic plating, resulting an average absolute increase in efficiency of 0.4% compared to cells fabricated without an emitter etch back process.

Evaluation of the toxic properties of naturally weathered Exxon Valdez crude oil to surrogate wildlife species

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stubblefield, W.A.; Hancock, G.A.; Ford, W.H.

1995-12-31

The toxic properties of naturally weathered Exxon Valdez crude oil (WEVC) to avian and mammalian wildlife species were evaluated using the surrogate species, mallard duck, Anas platyrhynchos, and European ferret, Mustela putorius. This study was conducted to evaluate the potential for toxic (rather than physical) injury to wildlife species that may have been exposed to WEVC, either through external contact or through dietary uptake. Previous studies have assessed the toxicity of unweathered crude oils, including Alaska North Slope Crude, but little information exists regarding the toxicity of a naturally weathered crude oil, typical of that encountered following a spill. Amore » battery of laboratory toxicity tests was conducted, in compliance with standard and published test procedures, to evaluate acute and subchronic toxicity of WEVC. These included tests of food avoidance, reproductive effects, and direct eggshell application toxicity. Naturally weathered EVC, recovered postspill from Prince William Sound, was used as the test material. 36 refs., 7 figs., 4 tabs.« less

Photonic and Plasmonic Nanotweezing of Nano- and Microscale Particles.

PubMed

Conteduca, Donato; Dell'Olio, Francesco; Krauss, Thomas F; Ciminelli, Caterina

2017-03-01

The ability to manipulate and sense biological molecules is important in many life science domains, such as single-molecule biophysics, the development of new drugs and cancer detection. Although the manipulation of biological matter at the nanoscale continues to be a challenge, several types of nanotweezers based on different technologies have recently been demonstrated to address this challenge. In particular, photonic and plasmonic nanotweezers are attracting a strong research effort especially because they are efficient and stable, they offer fast response time, and avoid any direct physical contact with the target object to be trapped, thus preventing its disruption or damage. In this paper, we critically review photonic and plasmonic resonant technologies for biomolecule trapping, manipulation, and sensing at the nanoscale, with a special emphasis on hybrid photonic/plasmonic nanodevices allowing a very strong light-matter interaction. The state-of-the-art of competing technologies, e.g., electronic, magnetic, acoustic and carbon nanotube-based nanotweezers, and a description of their applications are also included.

Glass microfluidic devices with thin membrane voltage junctions for electrospray mass spectrometry.

PubMed

Yue, Guihua Eileen; Roper, Michael G; Jeffery, Erin D; Easley, Christopher J; Balchunas, Catherine; Landers, James P; Ferrance, Jerome P

2005-06-01

In this study a novel glass membrane was prepared for conducting high voltage (HV) to solution in the channel of a microfabricated device for generation of liquid electrospray. Taylor cone formation and mass spectra obtained from this microdevice confirmed the utility of the glass membrane, but voltage conduction through the membrane could not be successfully explained based solely on the conductivity of the glass itself. This novel method for developing a high-voltage interface for microdevices avoids direct metal/liquid contact eliminating bubble formation in the channel due to water hydrolysis on the surface of the metal. Further, this arrangement produces no dead volume as is often found with traditional liquid junctions. At the same time, preliminary investigations into the outlet design of glass microdevices for interfacing with electrospray mass spectrometry, was explored. Both the exit shape and the use of hydrophobic coatings at the channel exit of the microdevice electrospray interface were evaluated using standard proteins with results indicating the utility of this type of design after further optimization.

ISMP Medication Error Report Analysis

PubMed Central

Cohen, Michael R.; Smetzer, Judy L.

2016-01-01

These medication errors have occurred in health care facilities at least once. They will happen again—perhaps where you work. Through education and alertness of personnel and procedural safeguards, they can be avoided. You should consider publishing accounts of errors in your newsletters and/or presenting them at your inservice training programs. Your assistance is required to continue this feature. The reports described here were received through the Institute for Safe Medication Practices (ISMP) Medication Errors Reporting Program. Any reports published by ISMP will be anonymous. Comments are also invited; the writers' names will be published if desired. ISMP may be contacted at the address shown below. Errors, close calls, or hazardous conditions may be reported directly to ISMP through the ISMP Web site (www.ismp.org), by calling 800-FAIL-SAFE, or via e-mail at ismpinfo@ismp.org. ISMP guarantees the confidentiality and security of the information received and respects reporters' wishes as to the level of detail included in publications. PMID:28057945

ISMP Medication Error Report Analysis

PubMed Central

Cohen, Michael R.; Smetzer, Judy L.

2016-01-01

ABSTRACT These medication errors have occurred in health care facilities at least once. They will happen again—perhaps where you work. Through education and alertness of personnel and procedural-safeguards, they can be avoided. You should consider publishing accounts of errors in your newsletters and/or presenting them at your inservice training programs. Your assistance is required to continue this feature. The reports described here were receivedthrough the Institute for Safe Medication Practices (ISMP) Medication Errors Reporting Program. Any reports published by ISMP will be anonymous. Comments are also invited; the writers' names will be published if desired. ISMP may be contacted at the address shown below. Errors, close calls, or hazardous conditions may be reported directly to ISMP through the ISMP Web site (www.ismp.org), by calling 800-FAIL-SAFE, or via e-mail at ismpinfo@ismp.org. ISMP guarantees the confidentiality and security of the information received and respects reporters' wishes as to the level of detail included in publications. PMID:27928183

Frictional Performance Assessment of Cemented Carbide Surfaces Textured by Laser

NASA Astrophysics Data System (ADS)

Fang, S.; Llanes, L.; Klein, S.; Gachot, C.; Rosenkranz, A.; Bähre, D.; Mücklich, F.

2017-10-01

Cemented carbides are advanced engineering materials often used in industry for manufacturing cutting tools or supporting parts in tribological system. In order to improve service life, special attention has been paid to change surface conditions by means of different methods, since surface modification can be beneficial to reduce the friction between the contact surfaces as well as to avoid unintended damage. Laser surface texturing is one of the newly developed surface modification methods. It has been successfully introduced to fabricate some basic patterns on cemented carbide surfaces. In this work, Direct Laser Interference Patterning Technique (DLIP) is implemented to produce special line-like patterns on a cobalt (Co) and nickel (Ni) based cemented tungsten carbide grade. It is proven that the laser-produced patterns have high geometrical precision and quality stability. Furthermore, tribology testing using a nano-tribometer unit shows that friction is reduced by the line-like patterns, as compared to the polished one, under both lubricated and dry testing regimes, and the reduction is more pronounced in the latter case.

37 CFR 10.33 - Direct contact with prospective clients.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Direct contact with prospective clients. 10.33 Section 10.33 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND... clients. A practitioner may not solicit professional employment from a prospective client with whom the...

Empathy and avoidance in treating patients living with HIV/AIDS (PLWHA) among service providers in China

PubMed Central

Lin, Chunqing; Li, Li; Wan, Dai; Wu, Zunyou; Yan, Zhihua

2012-01-01

This study aims to investigate health care providers’ empathy levels and its association with avoidance in providing service to patients living with HIV/AIDS (PLWHA) in China. A total of 1760 health service providers were randomly sampled from 40 county hospitals in two provinces of China. Using a self-administered questionnaire, participants’ demographic characteristics, work history, empathy level, and avoidance attitudes toward PLWHA were collected in a cross-sectional survey. Empathy was higher among participants aged 31–40 years, those who had an associated medical degree, and those who had served in the medical profession for less than 20 years. Nurses, younger providers, and providers with lower education tended to avoid contact with PLWHA. Multiple linear regression model showed that a higher level of empathic attitude toward patients was significantly negatively associated with avoidance attitude toward PLWHA. Service providers’ empathy level plays an important role in providing quality care to HIV-infected patients. Future stigma reduction interventions should cultivate empathy as a platform for understanding, effective communication, and trusting provider–patient relationships. PLWHA could potentially benefit from attitudinal change in medical settings. PMID:22292939

Obstacle detection and avoiding of quadcopter

NASA Astrophysics Data System (ADS)

Wang, Dizhong; Lin, Jiajian

2017-10-01

Recent years, the flight control technology over quadcopter has been boosted vigorously and acquired the comprehensive application in a variety of industries. However, it is prominent for there to be problems existed in the stable and secure flight with the development of its autonomous flight. Through comparing with the characteristics of ultrasonic ranging and laser Time-of-Flight(abbreviated to ToF) distance as well as vision measurement and its related sensors, the obstacle detection and identification sensors need to be installed in order to effectively enhance the safety flying for aircraft, which is essential for avoiding the dangers around the surroundings. That the major sensors applied to objects perception at present are distance measuring instruments which based on the principle and application of non-contact detection technology . Prior to acknowledging the general principles of flight and obstacle avoiding, the aerodynamics modeling of the quadcopter and its object detection means has been initially determined on this paper. Based on such premise, this article emphasized on describing and analyzing the research on obstacle avoiding technology and its application status, and making an expectation for the trend of its development after analyzing the primary existing problems concerning its accuracy object avoidance.

Ultraminiature Broadband Light Source and Method of Manufacturing Same

NASA Technical Reports Server (NTRS)

Tuma, Margaret L. (Inventor); Collura, Joseph S. (Inventor); Helvajian, Henry (Inventor); Pocha, Michael D. (Inventor); Meyer, Glenn A. (Inventor); McConaghy, Charles F. (Inventor); Olsen, Barry L. (Inventor); Hansen, William W. (Inventor)

2010-01-01

An ultraminiature light source using a double-spiral shaped tungsten filament includes end contact portions which are separated to allow for radial and length-wise unwinding of the spiral. The double-spiral filament is spaced relatively far apart at the end portions thereof so that contact between portions of the filament upon expansion is avoided. The light ource is made by fabricating a double-spiral ultraminiature tungsten filament from tungsten foil and housing the filament in a ceramic package having a reflective bottom and a well wherein the filament is suspended. A vacuum furnace brazing process attaches the filament to contacts of the ceramic package. Finally, a cover with a transparent window is attached onto the top of the ceramic package by solder reflow in a second vacuum furnace process to form a complete hermetically sealed package.

Symmetry-preserving contact interaction model for heavy-light mesons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serna, F. E.; Brito, M. A.; Krein, G.

2016-01-22

We use a symmetry-preserving regularization method of ultraviolet divergences in a vector-vector contact interaction model for low-energy QCD. The contact interaction is a representation of nonperturbative kernels used Dyson-Schwinger and Bethe-Salpeter equations. The regularization method is based on a subtraction scheme that avoids standard steps in the evaluation of divergent integrals that invariably lead to symmetry violation. Aiming at the study of heavy-light mesons, we have implemented the method to the pseudoscalar π and K mesons. We have solved the Dyson-Schwinger equation for the u, d and s quark propagators, and obtained the bound-state Bethe-Salpeter amplitudes in a way thatmore » the Ward-Green-Takahashi identities reflecting global symmetries of the model are satisfied for arbitrary routing of the momenta running in loop integrals.« less

Ultraminiature broadband light source with spiral shaped filament

NASA Technical Reports Server (NTRS)

McConaghy, Charles F. (Inventor); Olsen, Barry L. (Inventor); Tuma, Margaret L. (Inventor); Collura, Joseph S. (Inventor); Pocha, Michael D. (Inventor); Helvajian, Henry (Inventor); Meyer, Glenn A. (Inventor); Hansen, William W (Inventor)

2012-01-01

An ultraminiature light source using a double-spiral shaped tungsten filament includes end contact portions which are separated to allow for radial and length-wise unwinding of the spiral. The double-spiral filament is spaced relatively far apart at the end portions thereof so that contact between portions of the filament upon expansion is avoided. The light source is made by fabricating a double-spiral ultraminiature tungsten filament from tungsten foil and housing the filament in a ceramic package having a reflective bottom and a well wherein the filament is suspended. A vacuum furnace brazing process attaches the filament to contacts of the ceramic package. Finally, a cover with a transparent window is attached onto the top of the ceramic package by solder reflow in a second vacuum furnace process to form a complete hermetically sealed package.

Effect of Tibial Posterior Slope on Knee Kinematics, Quadriceps Force, and Patellofemoral Contact Force After Posterior-Stabilized Total Knee Arthroplasty.

PubMed

Okamoto, Shigetoshi; Mizu-uchi, Hideki; Okazaki, Ken; Hamai, Satoshi; Nakahara, Hiroyuki; Iwamoto, Yukihide

2015-08-01

We used a musculoskeletal model validated with in vivo data to evaluate the effect of tibial posterior slope on knee kinematics, quadriceps force, and patellofemoral contact force after posterior-stabilized total knee arthroplasty. The maximum quadriceps force and patellofemoral contact force decreased with increasing posterior slope. Anterior sliding of the tibial component and anterior impingement of the anterior aspect of the tibial post were observed with tibial posterior slopes of at least 5° and 10°, respectively. Increased tibial posterior slope contributes to improved exercise efficiency during knee extension, however excessive tibial posterior slope should be avoided to prevent knee instability. Based on our computer simulation we recommend tibial posterior slopes of less than 5° in posterior-stabilized total knee arthroplasty. Copyright © 2015 Elsevier Inc. All rights reserved.

Silver-free Metallization Technology for Producing High Efficiency, Industrial Silicon Solar Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michaelson, Lynne M.; Munoz, Krystal; Karas, Joseph

The goal of this project is to provide a commercially viable Ag-free metallization technology that will both reduce cost and increase efficiency of standard silicon solar cells. By removing silver from the front grid metallization and replacing it with lower cost nickel, copper, and tin metal, the front grid direct materials costs will decrease. This reduction in material costs should provide a path to meeting the Sunshot 2020 goal of 1 dollar / W DC. As of today, plated contacts are not widely implemented in large scale manufacturing. For organizations that wish to implement pilot scale manufacturing, only two equipmentmore » choices exist. These equipment manufacturers do not supply plating chemistry. The main goal of this project is to provide a chemistry and equipment solution to the industry that enables reliable manufacturing of plated contacts marked by passing reliability results and higher efficiencies than silver paste front grid contacts. To date, there have been several key findings that point to plated contacts performing equal to or better than the current state of the art silver paste contacts. Poor adhesion and reliability concerns are a few of the hurdles for plated contacts, specifically plated nickel directly on silicon. A key finding of the Phase 1 budget period is that the plated contacts have the same adhesion as the silver paste controls. This is a huge win for plated contacts. With very little optimization work, state of the art electrical results for plated contacts on laser ablated lines have been demonstrated with efficiencies up to 19.1% and fill factors ~80% on grid lines 40-50 um wide. The silver paste controls with similar line widths demonstrate similar electrical results. By optimizing the emitter and grid design for the plated contacts, it is expected that the electrical performance will exceed the silver paste controls. In addition, cells plated using Technic chemistry and equipment pass reliability testing; i.e. 1000 hours damp heat and 200 thermal cycles, with results similar to silver paste control cells. 100 cells have been processed through Technic’s novel demo plating tool built and installed during budget period 2. This plating tool performed consistently from cell to cell, providing gentle handling for the solar cells. An agreement has been signed with a cell manufacturer to process their cells through our plating chemistry and equipment. Their main focus for plated contacts is to reduce the direct materials cost by utilizing nickel, copper, and tin in place of silver paste. Based on current market conditions and cost model calculations, the overall savings offered by plated contacts is only 3.5% dollar/W versus silver paste contacts; however, the direct materials savings depend on the silver market. If silver prices increase, plated contacts may find a wider adoption in the solar industry in order to keep the direct materials costs down for front grid contacts.« less

Evaporation-induced flow in an inviscid liquid line at any contact angle

NASA Astrophysics Data System (ADS)

Petsi, A. J.; Burganos, V. N.

2006-04-01

The problem of potential flow inside an evaporating liquid line, shaped as an infinitely long cylindrical segment lying on a flat surface, is considered and an analytical solution is obtained for any contact angle in (0,π) . In this way, microflow details inside linear liquid bodies evaporating on hydrophilic, hydrophobic, and strongly hydrophobic substrates can now be obtained. The mathematical formulation employs the velocity potential and stream function formulations in bipolar coordinates and the solution is obtained using the technique of Fourier transform. Both pinned and depinned contact lines are considered. The solution is applicable to any evaporation mechanism but for illustration purposes numerical results are presented here for the particular case of kinetically controlled evaporation. For hydrophilic substrates, the flow inside the evaporating liquid line is directed towards the edges for pinned contact lines, thus, promoting a coffee stain effect. The opposite flow direction is observed for depinned contact lines. However, for strongly hydrophobic substrates, flow is directed outwards for both pinned and depinned contact lines, but owing to its low magnitude compared to that on hydrophilic substrates, a craterlike colloidal deposit should be expected rather than a ringlike deposit, in agreement with experimental observations.

Determination of contact angle from the maximum height of enlarged drops on solid surfaces

NASA Astrophysics Data System (ADS)

Behroozi, F.

2012-04-01

Measurement of the liquid/solid contact angle provides useful information on the wetting properties of fluids. In 1870, the German physicist Georg Hermann Quincke (1834-1924) published the functional relation between the maximum height of an enlarged drop and its contact angle. Quincke's relation offered an alternative to the direct measurement of contact angle, which in practice suffers from several experimental uncertainties. In this paper, we review Quincke's original derivation and show that it is based on a hidden assumption. We then present a new derivation that exposes this assumption and clarifies the conditions under which Quincke's relation is valid. To explore Quincke's relation experimentally, we measure the maximum height of enlarged water drops on several substrates and calculate the contact angle in each case. Our results are in good agreement with contact angles measured directly from droplet images.

Contact problem for an elastic reinforcement bonded to an elastic plate

NASA Technical Reports Server (NTRS)

Erdogan, F.; Civelek, M. B.

1974-01-01

The contact problem for a thin elastic reinforcement bonded to an elastic plate is considered. The stiffening layer is treated as an elastic membrane and the base plate is assumed to be an elastic continuum. The bonding between the two materials is assumed to be either one of direct adhesion or through a thin adhesive layer which is treated as a shear spring. The solution for the simple case in which both the stiffener and the base plate are treated as membranes is also given. The contact stress is obtained for a series of numerical examples. In the direct adhesion case the contact stress becomes infinite at the stiffener ends with a typical square root singularity for the continuum model and behaving as a delta function for the membrane model. In the case of bonding through an adhesive layer the contact stress becomes finite and continuous along the entire contact area.

Computerized Generation and Simulation of Meshing and Contact of New Type of Novikov-Wildhaber Helical Gears

NASA Technical Reports Server (NTRS)

Litvin, Faydor L.; Feng, Pin-Hao; Lagutin, Sergei A.

2000-01-01

In this report, we propose a new geometry for low-noise, increased-strength helical gears of the Novikov-Wildhaber type. Contact stresses are reduced as a result of their convex-concave gear tooth surfaces. The gear tooth surfaces are crowned in the profile direction to localize bearing contact and in the longitudinal direction to obtain a parabolic function of transmission errors. Such a function results in the reduction of noise and vibrations. Methods for the generation of the proposed gear tooth surfaces by grinding and hobbing are considered, and a tooth contact analysis (TCA) computer program to simulate meshing and contact is applied. The report also investigates the influence of misalignment on transmission errors and shift of bearing contact. Numerical examples to illustrate the developed approaches are proposed. The proposed geometry was patented by Ford/UIC (Serial Number 09-340-824, pending) on June 28, 1999.

Membrane Contact Sites: Complex Zones for Membrane Association and Lipid Exchange

PubMed Central

Quon, Evan; Beh, Christopher T.

2015-01-01

Lipid transport between membranes within cells involves vesicle and protein carriers, but as agents of nonvesicular lipid transfer, the role of membrane contact sites has received increasing attention. As zones for lipid metabolism and exchange, various membrane contact sites mediate direct associations between different organelles. In particular, membrane contact sites linking the plasma membrane (PM) and the endoplasmic reticulum (ER) represent important regulators of lipid and ion transfer. In yeast, cortical ER is stapled to the PM through membrane-tethering proteins, which establish a direct connection between the membranes. In this review, we consider passive and facilitated models for lipid transfer at PM–ER contact sites. Besides the tethering proteins, we examine the roles of an additional repertoire of lipid and protein regulators that prime and propagate PM–ER membrane association. We conclude that instead of being simple mediators of membrane association, regulatory components of membrane contact sites have complex and multilayered functions. PMID:26949334

21 CFR 882.1570 - Powered direct-contact temperature measurement device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Powered direct-contact temperature measurement device. 882.1570 Section 882.1570 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882...

21 CFR 882.1570 - Powered direct-contact temperature measurement device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Powered direct-contact temperature measurement device. 882.1570 Section 882.1570 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882...

Enterobius vermicularis infestation leading to Meckel's diverticulitis in an adolescent boy: An extremely rare presentation.

PubMed

Sharma, Manupriya; Kaul, Rashmi; Chander, Bal

2018-01-01

Enterobius vermicularis is an intestinal nematode commonly affecting children worldwide. Its transmission is by feco-oral route. Meckel's diverticulitis due to E. vermicularis infestation is an extremely rare presentation. An 11-year-old boy presented with acute abdomen. During surgery inflamed Meckel's diverticulum (M.D) was seen. Histopathology examination of specimen revealed E. vermicularis . Till date, only one case of E. vermicularis infestation of M.D is reported around five decades ago. This histopathological confirmation is extremely important as the required treatment (Mebendazole) of the infected case along with household contacts can prevent the spread of infection and may avoid surgery in known contacts.

Insights into semiconductor nanowire conductivity using electrodeposition

NASA Astrophysics Data System (ADS)

Liu, C.; Salehzadeh, O.; Poole, P. J.; Watkins, S. P.; Kavanagh, K. L.

2012-10-01

Copper (Cu) and iron (Fe) electrical contacts to gallium arsenide (GaAs) and indium arsenide (InAs) nanowires (NWs) have been fabricated via electrodeposition. For undoped or low carbon-doped (1017/cm-3), p-type GaAs NWs, Cu or Fe nucleate and grow only on the gold catalyst at the NW tip, avoiding the sidewalls. Metal growth is limited by the Au contact resistance due to thick sidewall depletion layers. For InAs NWs and heavier-doped, core-shell (undoped core-C-doped shell) GaAs NWs, metal nucleation and growth occurs on the sidewalls as well as on the gold catalyst limited now by the ion electrolyte diffusivity.

The friction free osteotome technique: introduction of a modified approach.

PubMed

Thalmair, Tobias; Fickl, Stefan; Bolz, Wolfgang; Wachtel, Hannes

2009-01-01

The current literature suggests that the bone-condensing approach while performing internal sinus floor elevation may not be beneficial for the future implant site. Furthermore, even with refined procedures, a predictable and controlled infraction of the sinus floor prior to graft placement still seems to be technique sensitive. In this context, the present article presents a modified technique along with the use of parallel osteotomes devoid of any contact to the lateral osteotomy wall. Therefore, compression of the adjacent bone will be avoided and the tactility of the site for the surgeon will be preserved as the osteotome is solely in contact with the subsinus cortex.

Population geography of calamity: the sixteenth and seventeenth century Yucatan.

PubMed

Whitmore, T M

1996-12-01

"This historical demography for Yucatan [Mexico] at the time of Spanish contact presents a number of problems. There were multiple Maya-Spaniard contacts before the Spaniards established a continuous presence after the protracted conquest of the Yucatan. The area of Yucatan that was controlled by the Spanish at any one time is not precisely known, and Yucatan offered ¿refuge' areas where the indigenous population could avoid Spanish control and counts. These issues are addressed here by considering different regions of the Yucatan and using a numerical computer simulation to generate new estimates of population that result from migration, warfare, agricultural calamity, and epidemics." excerpt

21 CFR 886.5916 - Rigid gas permeable contact lens.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Rigid gas permeable contact lens. 886.5916 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5916 Rigid gas permeable contact lens. (a) Identification. A rigid gas permeable contact lens is a device intended to be worn directly...

21 CFR 886.5916 - Rigid gas permeable contact lens.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Rigid gas permeable contact lens. 886.5916 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5916 Rigid gas permeable contact lens. (a) Identification. A rigid gas permeable contact lens is a device intended to be worn directly...

77 FR 12903 - 60-Day Notice of Proposed Information Collection: DS-158, Contact Information and Work History...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-02

..., Contact Information and Work History for Nonimmigrant Visa Applicant ACTION: Notice of request for public... with the Paperwork Reduction Act of 1995. Title of Information Collection: Contact Information and Work... FURTHER INFORMATION CONTACT: Direct requests for additional information regarding the collection listed in...

Endoplasmic Reticulum-Plasma Membrane Contact Sites.

PubMed

Saheki, Yasunori; De Camilli, Pietro

2017-06-20

The endoplasmic reticulum (ER) has a broad localization throughout the cell and forms direct physical contacts with all other classes of membranous organelles, including the plasma membrane (PM). A number of protein tethers that mediate these contacts have been identified, and study of these protein tethers has revealed a multiplicity of roles in cell physiology, including regulation of intracellular Ca 2+ dynamics and signaling as well as control of lipid traffic and homeostasis. In this review, we discuss the cross talk between the ER and the PM mediated by direct contacts. We review factors that tether the two membranes, their properties, and their dynamics in response to the functional state of the cell. We focus in particular on the role of ER-PM contacts in nonvesicular lipid transport between the two bilayers mediated by lipid transfer proteins.

16 CFR 1500.43a - Method of test for flashpoint of volatile flammable materials.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) below the target temperature, remove the cooling block and quickly dry the cup with a paper tissue to... (cooling) fluid is solid carbon dioxide (dry ice) and acetone. If the refrigerant charged cooling module is... pouring acetone. Use only in a well-ventilated area. Avoid inhalation and contact with the eyes or skin...

78 FR 53169 - Agency Information Collection Activities: Submission to OMB for Reinstatement, With Change, of a...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-28

... following information collection to the Office of Management and Budget (OMB) for review and clearance under... from the credit union's offices to avoid the simultaneous loss of both sets of records in the event of...-2861, Email: [email protected] . OMB Contact: Office of Management and Budget, ATTN: Desk Officer for...

77 FR 72327 - Takes of Marine Mammals Incidental to Specified Activities; Taking Marine Mammals Incidental to...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-05

... in the study plots or while biologists walk from one location to another. No motorized equipment is... selection of judicious routes of approach to study sites, avoiding close contact with pinnipeds hauled out on shore, and the use of extreme caution upon approach. In no case will marine mammals be...

78 FR 71550 - Approval and Promulgation of Air Quality Implementation Plans; State of Colorado Second Ten-Year...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-29

... INFORMATION CONTACT section to view the hard copy of the docket. You may view the hard copy of the docket... your concerns, and suggest alternatives. g. Explain your views as clearly as possible, avoiding the use..., Contingency Plan, and Transportation Conformity Requirements including the Motor Vehicle Emission Budget for...

Games as an Artistic Medium: Investigating Complexity Thinking in Game-Based Art Pedagogy

ERIC Educational Resources Information Center

Patton, Ryan M.

2013-01-01

This action research study examines the making of video games, using an integrated development environment software program called GameMaker, as art education curriculum for students between the ages of 8-13. Through a method I designed, students created video games using the concepts of move, avoid, release, and contact (MARC) to explore their…

Food allergy: practical approach on education and accidental exposure prevention.

PubMed

Pádua, I; Moreira, A; Moreira, P; Barros, R

2016-09-01

Food allergies are a growing problem and currently the primary treatment of food allergy is avoidance of culprit foods. However, given the lack of information and education and also the ubiquitous nature of allergens, accidental exposures to food allergens are not uncommon. The fear of potential fatal reactions and the need of a proper avoidance leads in most of the cases to the limitation of leisure and social activities. This review aims to be a practical approach on education and accidental exposure prevention regarding activities like shopping, eating out, and travelling. The recommendations are focused especially on proper reading of food labels and the management of the disease, namely in restaurants and airplanes, concerning cross-contact and communication with other stakeholders. The implementation of effective tools is essential to manage food allergy outside home, avoid serious allergic reactions and minimize the disease's impact on individuals' quality of life.

Attentional effects of masked famous faces (but not names) and subjective evaluations of a target person.

PubMed

Stone, Anna

2011-04-01

Two experiments are reported using a 1986 version of the dot-probe paradigm of MacLeod, Mathews, and Tata, in which the masked subliminal faces of famous persons were differentially associated with attention depending on participants' attitudes toward the famous person. There was attentional avoidance of the faces of persons invoking high disgust (Exp. 1, n=20) or dislike (Exp. 2) but attentional orientation toward the faces of persons invoking low disgust or liking. In Exp. 2 (n=28), this effect was apparent for the faces but not the names of famous persons, despite evidence that the famous names were recognised without awareness. The aversion of attention from faces, but not the names of famous persons who are regarded in a negative light but who are not particularly threatening, may suggest an automatic tendency to avoid making eye contact with an undesirable person thereby avoiding unwanted social interaction.

Alterations in knee contact forces and centers in stance phase of gait: A detailed lower extremity musculoskeletal model.

PubMed

Marouane, H; Shirazi-Adl, A; Adouni, M

2016-01-25

Evaluation of contact forces-centers of the tibiofemoral joint in gait has crucial biomechanical and pathological consequences. It involves however difficulties and limitations in in vitro cadaver and in vivo imaging studies. The goal is to estimate total contact forces (CF) and location of contact centers (CC) on the medial and lateral plateaus using results computed by a validated finite element model simulating the stance phase of gait for normal as well as osteoarthritis, varus-valgus and posterior tibial slope altered subjects. Using foregoing contact results, six methods commonly used in the literature are also applied to estimate and compare locations of CC at 6 periods of stance phase (0%, 5%, 25%, 50%, 75% and 100%). TF joint contact forces are greater on the lateral plateau very early in stance and on the medial plateau thereafter during 25-100% stance periods. Large excursions in the location of CC (>17mm), especially on the medial plateau in the mediolateral direction, are computed. Various reported models estimate quite different CCs with much greater variations (~15mm) in the mediolateral direction on both plateaus. Compared to our accurately computed CCs taken as the gold standard, the centroid of contact area algorithm yielded least differences (except in the mediolateral direction on the medial plateau at ~5mm) whereas the contact point and weighted center of proximity algorithms resulted overall in greatest differences. Large movements in the location of CC should be considered when attempting to estimate TF compartmental contact forces in gait. Copyright © 2015 Elsevier Ltd. All rights reserved.

Prospective multi-center study for quantification of chemotherapies and CTX-related direct medication costs avoided by use of biomarkers uPA and PAI-1 in primary breast cancer.

PubMed

Jacobs, Volker R; Augustin, Doris; Wischnik, Arthur; Kiechle, Marion; Höss, Cornelia; Steinkohl, Oliver; Rack, Brigitte; Kapitza, Thomas; Krase, Peter

2013-08-01

Biomarkers uPA/PAI-1 as recommended by ASCO and AGO are used in primary breast cancer to avoid unnecessary CTX in medium risk-recurrence patients. This study verified how many CTX cycles and CTX-related direct medication costs can be avoided by uPA/PAI-1 testing. A prospective, non-interventional, multi-center study was performed among six Certified Breast Centers to analyze application of uPA/PAI-1 and consecutive decision-making. CTX avoided were identified and direct costs for CTX, CTX-related concomitant medication and febrile neutropenia (FN) prophylaxis with G-CSF calculated. In n = 93 breast cancers n = 35 CTX (37.6%) with 210 CTX cycles were avoided according to uPA/PAI-1 test result. uPA/PAI-1 testing saved direct medication costs for CTX of 177,453 €, CTX-related concomitant medication of 27,482 € and FN prophylaxis of 20,599 €, overall 225,534 €. At test costs at 287.50 € uPA/PAI-1 testing resulted in additional costs of 26,737.50 €. uPA/PAI-1 has proven to be cost-effective at a return-on-investment ratio of 8.4:1. Indirect cost savings further increase this ROI. These results support decision-making for cost-effective diagnostics and therapy in breast cancer. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effect of direct eye contact in PTSD related to interpersonal trauma: an fMRI study of activation of an innate alarm system.

PubMed

Steuwe, Carolin; Daniels, Judith K; Frewen, Paul A; Densmore, Maria; Pannasch, Sebastian; Beblo, Thomas; Reiss, Jeffrey; Lanius, Ruth A

2014-01-01

In healthy individuals, direct eye contact initially leads to activation of a fast subcortical pathway, which then modulates a cortical route eliciting social cognitive processes. The aim of this study was to gain insight into the neurobiological effects of direct eye-to-eye contact using a virtual reality paradigm in individuals with posttraumatic stress disorder (PTSD) related to prolonged childhood abuse. We examined 16 healthy comparison subjects and 16 patients with a primary diagnosis of PTSD using a virtual reality functional magnetic resonance imaging paradigm involving direct vs averted gaze (happy, sad, neutral) as developed by Schrammel et al. in 2009. Irrespective of the displayed emotion, controls exhibited an increased blood oxygenation level-dependent response during direct vs averted gaze within the dorsomedial prefrontal cortex, left temporoparietal junction and right temporal pole. Under the same conditions, individuals with PTSD showed increased activation within the superior colliculus (SC)/periaqueductal gray (PAG) and locus coeruleus. Our findings suggest that healthy controls react to the exposure of direct gaze with an activation of a cortical route that enhances evaluative 'top-down' processes underlying social interactions. In individuals with PTSD, however, direct gaze leads to sustained activation of a subcortical route of eye-contact processing, an innate alarm system involving the SC and the underlying circuits of the PAG.

Effect of direct eye contact in PTSD related to interpersonal trauma: an fMRI study of activation of an innate alarm system

PubMed Central

Steuwe, Carolin; Daniels, Judith K.; Frewen, Paul A.; Densmore, Maria; Pannasch, Sebastian; Beblo, Thomas; Reiss, Jeffrey; Lanius, Ruth A.

2014-01-01

In healthy individuals, direct eye contact initially leads to activation of a fast subcortical pathway, which then modulates a cortical route eliciting social cognitive processes. The aim of this study was to gain insight into the neurobiological effects of direct eye-to-eye contact using a virtual reality paradigm in individuals with posttraumatic stress disorder (PTSD) related to prolonged childhood abuse. We examined 16 healthy comparison subjects and 16 patients with a primary diagnosis of PTSD using a virtual reality functional magnetic resonance imaging paradigm involving direct vs averted gaze (happy, sad, neutral) as developed by Schrammel et al. in 2009. Irrespective of the displayed emotion, controls exhibited an increased blood oxygenation level-dependent response during direct vs averted gaze within the dorsomedial prefrontal cortex, left temporoparietal junction and right temporal pole. Under the same conditions, individuals with PTSD showed increased activation within the superior colliculus (SC)/periaqueductal gray (PAG) and locus coeruleus. Our findings suggest that healthy controls react to the exposure of direct gaze with an activation of a cortical route that enhances evaluative ‘top–down’ processes underlying social interactions. In individuals with PTSD, however, direct gaze leads to sustained activation of a subcortical route of eye-contact processing, an innate alarm system involving the SC and the underlying circuits of the PAG. PMID:22977200

The direction of fluid flow during contact metamorphism of siliceous carbonate rocks: new data for the Monzoni and Predazzo aureoles, northern Italy, and a global review

NASA Astrophysics Data System (ADS)

Ferry, John M.; Wing, Boswell A.; Penniston-Dorland, Sarah C.; Rumble, Douglas

2002-03-01

Periclase formed in siliceous dolomitic marbles during contact metamorphism in the Monzoni and Predazzo aureoles, the Dolomites, northern Italy, by infiltration of the carbonate rocks by chemically reactive, H2O-rich fluids at 500 bar and 565-710 °C. The spatial distribution of periclase and oxygen isotope compositions is consistent with reactive fluid flow that was primarily vertical and upward in both aureoles with time-integrated flux ~5,000 and ~300 mol fluid/cm2 rock in the Monzoni and Predazzo aureoles, respectively. The new results for Monzoni and Predazzo are considered along with published studies of 13 other aureoles to draw general conclusions about the direction, amount, and controls on the geometry of reactive fluid flow during contact metamorphism of siliceous carbonate rocks. Flow in 12 aureoles was primarily vertically upward with and without a horizontal component directed away from the pluton. Fluid flow in two of the other three was primarily horizontal, directed from the pluton into the aureole. The direction of flow in the remaining aureole is uncertain. Earlier suggestions that fluid flow is often horizontal, directed toward the pluton, are likely explained by an erroneous assumption that widespread coexisting mineral reactants and products represent arrested prograde decarbonation reactions. With the exception of three samples from one aureole, time-integrated fluid flux was in the range 102-104 mol/cm2. Both the amount and direction of fluid flow are consistent with hydrodynamic models of contact metamorphism. The orientation of bedding and lithologic contacts appears to be the principal control over whether fluid flow was either primarily vertical or horizontal. Other pre-metamorphic structures, including dikes, faults, fold hinges, and fracture zones, served to channel fluid flow as well.

The direction of fluid flow during contact metamorphism of siliceous carbonate rocks: new data for the Monzoni and Predazzo aureoles, northern Italy, and a global review

NASA Astrophysics Data System (ADS)

Ferry, John; Wing, Boswell; Penniston-Dorland, Sarah; Rumble, Douglas

2001-11-01

Periclase formed in siliceous dolomitic marbles during contact metamorphism in the Monzoni and Predazzo aureoles, the Dolomites, northern Italy, by infiltration of the carbonate rocks by chemically reactive, H2O-rich fluids at 500 bar and 565-710 °C. The spatial distribution of periclase and oxygen isotope compositions is consistent with reactive fluid flow that was primarily vertical and upward in both aureoles with time-integrated flux 5,000 and 300 mol fluid/cm2 rock in the Monzoni and Predazzo aureoles, respectively. The new results for Monzoni and Predazzo are considered along with published studies of 13 other aureoles to draw general conclusions about the direction, amount, and controls on the geometry of reactive fluid flow during contact metamorphism of siliceous carbonate rocks. Flow in 12 aureoles was primarily vertically upward with and without a horizontal component directed away from the pluton. Fluid flow in two of the other three was primarily horizontal, directed from the pluton into the aureole. The direction of flow in the remaining aureole is uncertain. Earlier suggestions that fluid flow is often horizontal, directed toward the pluton, are likely explained by an erroneous assumption that widespread coexisting mineral reactants and products represent arrested prograde decarbonation reactions. With the exception of three samples from one aureole, time-integrated fluid flux was in the range 102-104 mol/cm2. Both the amount and direction of fluid flow are consistent with hydrodynamic models of contact metamorphism. The orientation of bedding and lithologic contacts appears to be the principal control over whether fluid flow was either primarily vertical or horizontal. Other pre-metamorphic structures, including dikes, faults, fold hinges, and fracture zones, served to channel fluid flow as well.

Pain during awake craniotomy for brain tumor resection. Incidence, causes, consequences and management.

PubMed

Fontaine, D; Almairac, F

2017-06-01

Awake craniotomy for brain tumor resection is usually well-tolerated and most of the patients are satisfied. However, in studies reporting the patients' postoperative perception of the awake craniotomy procedure, about half of them have experienced some degree of intraoperative pain. Pain was mild (intensity between 1 and 2 on the visual analogical score) short lasting in most cases, and did not challenge the procedure. Pain was reported as moderate in about 25% and exceptionally severe. We conducted a preliminary survey among French centers (n=9) routinely performing awake craniotomy. Neurosurgeons' opinions were concordant with patient's reports. Intraoperative pain exceptionally challenged the awake craniotomy procedure or led to changes in the resection strategy. For neurosurgeons, the most challenging causes of intraoperative pain were the patient's inadequate installation, the contact of surgical tools with pain-sensitive intracranial structures, especially the dura mater of the skull base, falx cerebri, and the leptomeninges of the lateral fissure and neighboring sulci. Strategies to deal with these causes included focusing the patient on the intraoperative functional tests to distract their attention away from the pain, and avoiding contacts with the pain-sensitive intracranial structures during the awake phase. Adequate preoperative patient information and preparation, trained anesthesiologists and application of recommendations for awake craniotomy procedures as well as adaptation of surgical technique to avoid contact with pain-sensitive intracranial structures are key factors to prevent intraoperative pain and ensure patient's postoperative satisfaction. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Passive Fetal Heart Monitoring System

NASA Technical Reports Server (NTRS)

Zuckerwar, Allan J. (Inventor); Mowrey, Dennis L. (Inventor)

2003-01-01

A fetal heart monitoring system and method for detecting and processing acoustic fetal heart signals transmitted by different signal transmission modes. One signal transmission mode, the direct contact mode, occurs in a first frequency band when the fetus is in direct contact with the maternal abdominal wall. Another signal transmission mode, the fluid propagation mode, occurs in a second frequency band when the fetus is in a recessed position with no direct contact with the maternal abdominal wall. The second frequency band is relatively higher than the first frequency band. The fetal heart monitoring system and method detect and process acoustic fetal heart signals that are in the first frequency band and in the second frequency band.

Apraxia

MedlinePlus

... important for people with aprexia. To help with communication, family and friends should: Avoid giving complex directions. Use simple phrases to avoid misunderstandings. Speak in a normal tone of ... communication aids, if possible, depending on the person and ...

Dispositional anger and the resolution of the approach-avoidance conflict.

PubMed

Robinson, Michael D; Boyd, Ryan L; Persich, Michelle R

2016-09-01

The approach-avoidance conflict is one in which approaching reward brings increased threat while avoiding threat means forgoing reward. This conflict can be uniquely informative because it will be resolved in different ways depending on whether approach (toward) or avoidance (away from) is the stronger motive. Two studies (total N = 191) created a computerized version of this conflict and used the test to examine questions of motivational direction in anger. In Study 1, noise blast provocations increased the frequency of approach behaviors at high levels of trait anger, but decreased their frequency at low levels. In Study 2, a simpler version of the conflict test was used to predict anger in daily life. As hypothesized, greater approach frequencies in the test predicted greater anger reactivity to daily provocations and frustrations. The discussion focuses on the utility of the approach-avoidance conflict test and on questions of motivational direction in anger. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Direct physical contact between intercalated cells in the distal convoluted tubule and the afferent arteriole in mouse kidneys.

PubMed

Ren, Hao; Liu, Ning-Yu; Andreasen, Arne; Thomsen, Jesper S; Cao, Liu; Christensen, Erik I; Zhai, Xiao-Yue

2013-01-01

Recent physiological studies in the kidney proposed the existence of a secondary feedback mechanism termed 'crosstalk' localized after the macula densa. This newly discovered crosstalk contact between the nephron tubule and its own afferent arteriole may potentially revolutionize our understanding of renal vascular resistance and electrolyte regulation. However, the nature of such a crosstalk mechanism is still debated due to a lack of direct and comprehensive morphological evidence. Its exact location along the nephron, its prevalence among the different types of nephrons, and the type of cells involved are yet unknown. To address these issues, computer assisted 3-dimensional nephron tracing was applied in combination with direct immunohistochemistry on plastic sections and electron microscopy. 'Random' contacts in the cortex were identified by the tracing and excluded. We investigated a total of 168 nephrons from all cortical regions. The results demonstrated that the crosstalk contact existed, and that it was only present in certain nephrons (90% of the short-looped and 75% of the long-looped nephrons). The crosstalk contacts always occurred at a specific position--the last 10% of the distal convoluted tubule. Importantly, we demonstrated, for the first time, that the cells found in the tubule wall at the contact site were always type nonA-nonB intercalated cells. In conclusion, the present work confirmed the existence of a post macula densa physical crosstalk contact.

Application of lateral photovoltage towards contactless light beam induced current measurements and its dependence on the finite beam size

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abhale, Atul Prakash; Rao, K. S. R. Koteswara, E-mail: ksrkrao@physics.iisc.erent.in

2014-07-15

The nature of the signal due to light beam induced current (LBIC) at the remote contacts is verified as a lateral photovoltage for non-uniformly illuminated planar p-n junction devices; simulation and experimental results are presented. The limitations imposed by the ohmic contacts are successfully overcome by the introduction of capacitively coupled remote contacts, which yield similar results without any significant loss in the estimated material and device parameters. It is observed that the LBIC measurements introduce artefacts such as shift in peak position with increasing laser power. Simulation of LBIC signal as a function of characteristic length L{sub c} ofmore » photo-generated carriers and for different beam diameters has resulted in the observed peak shifts, thus attributed to the finite size of the beam. Further, the idea of capacitively coupled contacts has been extended to contactless measurements using pressure contacts with an oxidized aluminium electrodes. This technique avoids the contagious sample processing steps, which may introduce unintentional defects and contaminants into the material and devices under observation. Thus, we present here, the remote contact LBIC as a practically non-destructive tool in the evaluation of device parameters and welcome its use during fabrication steps.« less

Construction of adhesion maps for contacts between a sphere and a half-space: Considering size effects of the sphere.

PubMed

Zhang, Yuyan; Wang, Xiaoli; Li, Hanqing; Yang, Weixu

2015-11-15

Previous adhesion maps, such as the JG (Johnson-Greenwood) and YCG (Yao-Ciavarella-Gao) maps, are used to guide the selection of Bradley, DMT, M-D, JKR and Hertz models. However, when the size of the contact sphere decreases to the small scale, the applicability of JG and YCG maps is limited because the assumptions regarding the contact region profile, interaction between contact bodies and sphere shape in the classical models constituting these two maps are no longer valid. To avoid this limitation, in this paper, a new numerical model considering size effects of the sphere is established first and then introduced into the new adhesion maps together with the YGG (Yao-Guduru-Gao) model and Hertz model. Regimes of these models in the new map under a certain sphere radius are demarcated by the criteria related to the relative force differences and the ratio of contact radius to sphere radius. In addition, the approaches at pull-off, jump-in and jump-out for different Tabor parameters and sphere radii are provided in the new maps. Finally, to make the new maps more feasible, the numerical results of approaches, force and contact radius involved in the maps are formularized by using the piecewise fitting. Copyright © 2015 Elsevier Inc. All rights reserved.

Advancements in non-contact metrology of asphere and diffractive optics

NASA Astrophysics Data System (ADS)

DeFisher, Scott

2017-11-01

Advancements in optical manufacturing technology allow optical designers to implement steep aspheric or high departure surfaces into their systems. Measuring these surfaces with profilometers or CMMs can be difficult due to large surface slopes or sharp steps in the surface. OptiPro has developed UltraSurf to qualify the form and figure of steep aspheric and diffractive optics. UltraSurf is a computer controlled, non-contact coordinate measuring machine. It incorporates five air-bearing axes, linear motors, high-resolution feedback, and a non-contact probe. The measuring probe is scanned over the optical surface while maintaining perpendicularity and a constant focal offset. Multiple probe technologies are available on UltraSurf. Each probe has strengths and weaknesses relative to the material properties, surface finish, and figure error of an optical component. The measuring probes utilize absolute distance to resolve step heights and diffractive surface patterns. The non-contact scanning method avoids common pitfalls with stylus contact instruments. Advancements in measuring speed and precision has enabled fast and accurate non-contact metrology of diffractive and steep aspheric surfaces. The benefits of data sampling with twodimensional profiles and three-dimensional topography maps will be presented. In addition, accuracy, repeatability, and machine qualification will be discussed with regards to aspheres and diffractive surfaces.

Eczema (For Parents)

MedlinePlus

... the skin to become scaly and inflamed), and contact dermatitis (caused by direct skin contact with an irritating substance, such as a metal, ... How Do I Get Rid of Eczema Scars? Eczema Impetigo View more About Us Contact Us Partners Editorial Policy Permissions Guidelines Privacy Policy & ...

Multi-stage flash degaser

DOEpatents

Rapier, P.M.

1980-06-26

A multi-stage flash degaser is incorporated in an energy conversion system having a direct-contact, binary-fluid heat exchanger to remove essentially all of the noncondensable gases from geothermal brine ahead of the direct-contact binary-fluid heat exchanger in order that the heat exchanger and a turbine and condenser of the system can operate at optimal efficiency.

Industrial applications of the air direct-contact, gravel, ground heat exchanger

NASA Astrophysics Data System (ADS)

Cepiński, Wojciech; Besler, Maciej

2017-11-01

The paper describes the analysis of possibility of using the air direct-contact, gravel, ground heat exchanger (Polish acronym BGWCiM), patented at the Wroclaw University of Science and Technology to prepare air for conditioning rooms in the industry. Indicated the industry sectors where the application may be the most beneficial.

The Relationship between Bullying Victimization and School Avoidance: An Examination of Direct Associations, Protective Influences, and Aggravating Factors

ERIC Educational Resources Information Center

Hutzell, Kirsten L.; Payne, Allison Ann

2018-01-01

This study examines the impact of bullying victimization on school avoidance by proposing the following hypotheses: (1) Net of other factors, students who have experienced bullying victimization are more likely to engage in school avoidance behaviors; (2) There are protective factors that will decrease this relationship between bullying…

Validation of radiocarpal joint contact models based on images from a clinical MRI scanner.

PubMed

Johnson, Joshua E; McIff, Terence E; Lee, Phil; Toby, E Bruce; Fischer, Kenneth J

2014-01-01

This study was undertaken to assess magnetic resonance imaging (MRI)-based radiocarpal surface contact models of functional loading in a clinical MRI scanner for future in vivo studies, by comparison with experimental measures from three cadaver forearm specimens. Experimental data were acquired using a Tekscan sensor during simulated light grasp. Magnetic resonance (MR) images were used to obtain model geometry and kinematics (image registration). Peak contact pressures (PPs) and average contact pressures (APs), contact forces and contact areas were determined in the radiolunate and radioscaphoid joints. Contact area was also measured directly from MR images acquired with load and compared with model data. Based on the validation criteria (within 25% of experimental data), out of the six articulations (three specimens with two articulations each), two met the criterion for AP (0%, 14%); one for peak pressure (20%); one for contact force (5%); four for contact area with respect to experiment (8%, 13%, 19% and 23%), and three contact areas met the criterion with respect to direct measurements (14%, 21% and 21%). Absolute differences between model and experimental PPs were reasonably low (within 2.5 MPa). Overall, the results indicate that MRI-based models generated from 3T clinical MR scanner appear sufficient to obtain clinically relevant data.

Handbook on Coral Reef Impacts: Avoidance, Minimization, Compensatory Mitigation, and Restoration

EPA Pesticide Factsheets

This Handbook provides a general summary of current avoidance, minimization, compensatory mitigation, and restoration strategies that may help address physical damage resulting from direct adverse impacts to coral reefs.

An open design microfabricated nib-like nanoelectrospray emitter tip on a conducting silicon substrate for the application of the ionization voltage.

PubMed

Le Gac, Séverine; Rolando, Christian; Arscott, Steve

2006-01-01

This paper describes a novel emitter tip having the shape of a nib and based on an open structure for nano-electrospray ionization mass spectrometry (nanoESI-MS). The nib structure is fabricated with standard lithography techniques using SU-8, an epoxy-based negative photoresist. The tip is comprised of a reservoir, a capillary slot and a point-like feature, and is fabricated on a silicon wafer. We present here a novel scheme for interfacing such nib tips to MS by applying the ionization voltage directly onto the semi-conductor support. The silicon support is in direct contact with the liquid to be analyzed at the reservoir and microchannel level, thus allowing easy use in ESI-MS. This scheme is especially advantageous for automated analysis as the manual step of positioning a metallic wire into the reservoir is avoided. In addition, the analysis performance was enhanced compared with the former scheme, as demonstrated by the tests of standard peptides (gramicidin S, Glu-fibrinopeptide B). The limit of detection was determined to be lower than 10(-2) microM. Due to their enhanced performance, these microfabricated sources might be of great interest for analysis requiring very high sensitivity, such as proteomics analysis using nanoESI-MS.

Smart Sound Processing for Defect Sizing in Pipelines Using EMAT Actuator Based Multi-Frequency Lamb Waves

PubMed Central

García-Gómez, Joaquín; Rosa-Zurera, Manuel; Romero-Camacho, Antonio; Jiménez-Garrido, Jesús Antonio; García-Benavides, Víctor

2018-01-01

Pipeline inspection is a topic of particular interest to the companies. Especially important is the defect sizing, which allows them to avoid subsequent costly repairs in their equipment. A solution for this issue is using ultrasonic waves sensed through Electro-Magnetic Acoustic Transducer (EMAT) actuators. The main advantage of this technology is the absence of the need to have direct contact with the surface of the material under investigation, which must be a conductive one. Specifically interesting is the meander-line-coil based Lamb wave generation, since the directivity of the waves allows a study based in the circumferential wrap-around received signal. However, the variety of defect sizes changes the behavior of the signal when it passes through the pipeline. Because of that, it is necessary to apply advanced techniques based on Smart Sound Processing (SSP). These methods involve extracting useful information from the signals sensed with EMAT at different frequencies to obtain nonlinear estimations of the depth of the defect, and to select the features that better estimate the profile of the pipeline. The proposed technique has been tested using both simulated and real signals in steel pipelines, obtaining good results in terms of Root Mean Square Error (RMSE). PMID:29518927

One-pot deposition of palladium on hybrid TiO2 nanoparticles and catalytic applications in hydrogenation.

PubMed

Mehri, Afef; Kochkar, Hafedh; Daniele, Stéphane; Mendez, Violaine; Ghorbel, Abdelhamid; Berhault, Gilles

2012-03-01

One-pot deposition of Pd onto TiO(2) has been achieved through directly contacting palladium(II) salt with nanosized functionalized TiO(2) support initially obtained by sol-gel process using titanium isopropoxide and citric acid. Citrate groups act as functional moieties able to directly reduce the Pd salt avoiding any further reducing treatment. Various palladium salts (Na(2)PdCl(4) and Pd(NH(3))(4)Cl(2)·H(2)O) and titanium to citrate (Ti/CA) ratios (20, 50, and 100) were used in order to study the effect of the nature of the precursor and of the citrate content on the final Pd particle size and catalytic properties of the as-obtained Pd/TiO(2) systems. Characterization was performed using N(2) adsorption-desorption isotherms, ICP-AES, FTIR, XRD, XPS, and TEM. The as-obtained hybrid Pd/TiO(2) catalysts were tested in the selective hydrogenation (HYD) of an α,β-unsaturated aldehyde, i.e. cinnamaldehyde. Citrate-free Pd/TiO(2)-based catalysts present lower selectivity into saturated alcohol. However, citrate-functionalized Pd/TiO(2) catalyst seems to control the selectivity, the particle size and dispersion of Pd NPs leading to high intrinsic activity. Copyright © 2011 Elsevier Inc. All rights reserved.

Cellular phone collateral damage: A review of burns associated with lithium battery powered mobile devices.

PubMed

Mankowski, Peter J; Kanevsky, Jonathan; Bakirtzian, Parseh; Cugno, Sabrina

2016-06-01

The spontaneous destruction of lithium battery powered cellphones has raised concern about the safety of these devices. We present a case report and review of the literature of burn injuries sustained in association with cellular phone usage. A Medline search was performed to identify articles describing cellular phone associated thermal injuries using key search words including "burn," "burn injury," "cellular phone," "cellphone," "thermal injury," and "telephone." Articles were reviewed for etiology, location, severity and treatment. We also present a case of a burn to the upper thigh resulting from cellular phone battery malfunction. Six case reports were identified detailing burn injuries obtained from cellphone use. Half of these cases occurred from battery malfunction with second degree being the most common severity. All cases were managed conservatively except one case, which required excision and primary closure. Lithium powered cellular phones are susceptible to overheating and destruction from inadequate heat dissipation during thermal runaway. This process can be initiated by local short-circuiting from direct contact with a low resistance conductor such as keys or coins. We reinforce the importance of safe cell phone battery practices including avoiding overcharging and direct skin exposure to minimize thermal injury risk. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Safe Direct Current Stimulation to Expand Capabilities of Neural Prostheses

PubMed Central

Fridman, Gene Y.; Della Santina, Charles C.

2014-01-01

While effective in treating some neurological disorders, neuroelectric prostheses are fundamentally limited because they must employ charge-balanced stimuli to avoid evolution of irreversible electrochemical reactions and their byproducts at the interface between metal electrodes and body fluids. Charge-balancing is typically achieved by using brief biphasic alternating current (AC) pulses, which typically excite nearby neural tissues but cannot efficiently inhibit them. In contrast, direct current (DC) applied via a metal electrode in contact with body fluids can excite, inhibit and modulate sensitivity of neurons; however, DC stimulation is biologically unsafe because it violates “safe charge injection” limits that have long been considered unavoidable constraints. In this report, we describe the design and fabrication of a safe DC stimulator (SDCS) that overcomes this constraint. The SCDS drives DC ionic current into target tissue via salt-bridge micropipette electrodes by switching valves in phase with AC square waves applied to metal electrodes contained within the device. This approach achieves DC ionic flow through tissue while still adhering to charge-balancing constraints at each electrode-saline interface. We show the SDCS’s ability to both inhibit and excite neural activity to achieve improved dynamic range during prosthetic stimulation of the vestibular part of the inner ear in chinchillas. PMID:23476007

An Aromatic Sensor with Aversion to Damaged Strands Confers Versatility to DNA Repair

PubMed Central

Maillard, Olivier; Solyom, Szilvia; Naegeli, Hanspeter

2007-01-01

It was not known how xeroderma pigmentosum group C (XPC) protein, the primary initiator of global nucleotide excision repair, achieves its outstanding substrate versatility. Here, we analyzed the molecular pathology of a unique Trp690Ser substitution, which is the only reported missense mutation in xeroderma patients mapping to the evolutionary conserved region of XPC protein. The function of this critical residue and neighboring conserved aromatics was tested by site-directed mutagenesis followed by screening for excision activity and DNA binding. This comparison demonstrated that Trp690 and Phe733 drive the preferential recruitment of XPC protein to repair substrates by mediating an exquisite affinity for single-stranded sites. Such a dual deployment of aromatic side chains is the distinctive feature of functional oligonucleotide/oligosaccharide-binding folds and, indeed, sequence homologies with replication protein A and breast cancer susceptibility 2 protein indicate that XPC displays a monomeric variant of this recurrent interaction motif. An aversion to associate with damaged oligonucleotides implies that XPC protein avoids direct contacts with base adducts. These results reveal for the first time, to our knowledge, an entirely inverted mechanism of substrate recognition that relies on the detection of single-stranded configurations in the undamaged complementary sequence of the double helix. PMID:17355181

78 FR 63408 - Petition To Amend Animal Welfare Act Regulations To Prohibit Public Contact With Big Cats, Bears...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-24

... Regulations To Prohibit Public Contact With Big Cats, Bears, and Nonhuman Primates AGENCY: Animal and Plant... into direct or physical contact with big cats, bears, or nonhuman primates of any age, to define the... coming. FOR FURTHER INFORMATION CONTACT: Dr. Barbara Kohn, DVM, Senior Staff Officer, USDA, APHIS, Animal...