DEM generation from contours and a low-resolution DEM

NASA Astrophysics Data System (ADS)

Li, Xinghua; Shen, Huanfeng; Feng, Ruitao; Li, Jie; Zhang, Liangpei

2017-12-01

A digital elevation model (DEM) is a virtual representation of topography, where the terrain is established by the three-dimensional co-ordinates. In the framework of sparse representation, this paper investigates DEM generation from contours. Since contours are usually sparsely distributed and closely related in space, sparse spatial regularization (SSR) is enforced on them. In order to make up for the lack of spatial information, another lower spatial resolution DEM from the same geographical area is introduced. In this way, the sparse representation implements the spatial constraints in the contours and extracts the complementary information from the auxiliary DEM. Furthermore, the proposed method integrates the advantage of the unbiased estimation of kriging. For brevity, the proposed method is called the kriging and sparse spatial regularization (KSSR) method. The performance of the proposed KSSR method is demonstrated by experiments in Shuttle Radar Topography Mission (SRTM) 30 m DEM and Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) 30 m global digital elevation model (GDEM) generation from the corresponding contours and a 90 m DEM. The experiments confirm that the proposed KSSR method outperforms the traditional kriging and SSR methods, and it can be successfully used for DEM generation from contours.

Merging of an EET CInSAR DEM with the SRTM DEM

NASA Astrophysics Data System (ADS)

Wegmuller, Urs; Wiesmann, Andreas; Santoro, Maurizio

2010-03-01

Cross-interferometry (CInSAR) using ERS-2 and ENVISAT ASAR SAR data acquired in the ERS like mode IS2 at VV-polarization with perpendicular baselines of approximately 2 kilometers permits generation of digital elevation models (DEMs). Thanks to the long perpendicular baselines CInSAR has a good potential to generate accurate DEMs over relatively flat terrain. Over sloped terrain the topographic phase gradients get very high and the signals decorrelate if the carrier frequency difference and the baseline effects do not compensate any more. As a result phase unwrapping gets very difficult so that often no reliable solution is obtained for hilly terrain, resulting in DEMs with significant spatial gaps.Spatial gaps in ERS-2 ENVISAT Tandem (EET) CInSAR DEMs over hilly terrain are clearly an important limitation to the utility of these DEMs. On the other hand the high quality achieved over relatively flat terrain is of high interest. As an attempt to significantly improve the utility of the "good information" contained in the CInSAR DEM we developed a methodology to merge a CInSAR DEM with another available DEM, e.g. the SRTM DEM.The methodology was applied to an area in California, USA, including relatively flat terrain belonging to the Mohave desert as well as hilly to mountainous terrain of the San Gabriel and Tehachapi Mountains.

b.i.t. Bremerhaven: Thin Clients entlasten Schulen

NASA Astrophysics Data System (ADS)

Das Schulamt Bremerhaven zentralisiert die Verwaltungs-IT und schafft dadurch Freiräume für pädagogische und organisatorische Herausforderungen. Pflege und Support der neuen Infrastruktur übernimmt der Dienstleister b.i.t. Bremerhaven, die Thin Clients kommen vom Bremer Hersteller IGEL Technology. Ganztagsschulen, das 12-jährige Abitur, PISA, der Wegfall der Orientierungsstufe - deutsche Schulen müssen derzeit zahlreiche organisatorische und pädagogische Herausforderungen bewältigen. Um die neuen Strukturen umsetzen zu können, werden zusätzliche Ressourcen benötigt. Das Schulamt Bremerhaven hat gemeinsam mit dem Dienstleister b.i.t. Bremerhaven (Betrieb für Informationstechnologie) eine intelligente Lösung gefunden, wie sich die benötigten finanziellen Freiräume schaffen lassen.

Der Einfluss von Alitretinoin auf die Lebensqualität bei Patienten mit schwerem chronischen Handekzem: FUGETTA - Beobachtungsstudie unter Praxisbedingungen.

PubMed

Augustin, Matthias; Thaçi, Diamant; Kamps, Anja

2016-12-01

Alitretinoin ist die einzige zugelassene Behandlung für schweres chronisches Handekzem (CHE), das refraktär gegenüber potenten topischen Corticosteroiden ist. Bei dieser Studie (FUGETTA) wurde die Wirksamkeit von leitliniengerecht angewendetem oralem Alitretinoin sowie dessen Einfluss auf die Lebensqualität (LQ) bei Patienten mit schwerem refraktärem CHE beurteilt. Multizentrische, offene, nichtinterventionelle Beobachtungsstudie, durchgeführt in Deutschland. Die Patienten wurden nach Ermessen ihres behandelnden Arztes mit Alitretinoin 10 mg oder 30 mg einmal täglich über maximal 24 Wochen behandelt. Die Wirksamkeit wurde anhand des Physician Global Assessment (PGA) und des Dermatology Life Quality Index (DLQI) bewertet. Zudem wurden unerwünschte Ereignisse (UE) erfasst. Die Studienpopulation bestand aus 658 Patienten (30 mg: n = 581; 10 mg: n = 77). Bei Beobachtungsbeginn litten die meisten Patienten (83 %) gemäß PGA an einem schweren CHE. Bei Beobachtungsende war das Handekzem bei 48 % der Patienten gemäß PGA vollständig oder fast vollständig abgeheilt (30 mg: 49 %; 10 mg: 43 %). Die mittlere Verbesserung des DLQI-Scores in Woche 24 betrug 58 % (30 mg: mittlere [SD] Veränderung gegenüber dem Ausgangswert -10,4 [8,04]) und 70 % (10 mg: mittlere [SD] Veränderung gegenüber dem Ausgangswert -10,8 [7,29]). Die Gesamtinzidenz von NW war niedrig und in den beiden Gruppen ähnlich. Alitretinoin führte zu einer schnellen, deutlichen Verbesserung der LQ bei Patienten mit schwerem CHE. © 2016 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

`Dem DEMs: Comparing Methods of Digital Elevation Model Creation

NASA Astrophysics Data System (ADS)

Rezza, C.; Phillips, C. B.; Cable, M. L.

2017-12-01

Topographic details of Europa's surface yield implications for large-scale processes that occur on the moon, including surface strength, modification, composition, and formation mechanisms for geologic features. In addition, small scale details presented from this data are imperative for future exploration of Europa's surface, such as by a potential Europa Lander mission. A comparison of different methods of Digital Elevation Model (DEM) creation and variations between them can help us quantify the relative accuracy of each model and improve our understanding of Europa's surface. In this work, we used data provided by Phillips et al. (2013, AGU Fall meeting, abs. P34A-1846) and Schenk and Nimmo (2017, in prep.) to compare DEMs that were created using Ames Stereo Pipeline (ASP), SOCET SET, and Paul Schenk's own method. We began by locating areas of the surface with multiple overlapping DEMs, and our initial comparisons were performed near the craters Manannan, Pwyll, and Cilix. For each region, we used ArcGIS to draw profile lines across matching features to determine elevation. Some of the DEMs had vertical or skewed offsets, and thus had to be corrected. The vertical corrections were applied by adding or subtracting the global minimum of the data set to create a common zero-point. The skewed data sets were corrected by rotating the plot so that it had a global slope of zero and then subtracting for a zero-point vertical offset. Once corrections were made, we plotted the three methods on one graph for each profile of each region. Upon analysis, we found relatively good feature correlation between the three methods. The smoothness of a DEM depends on both the input set of images and the stereo processing methods used. In our comparison, the DEMs produced by SOCET SET were less smoothed than those from ASP or Schenk. Height comparisons show that ASP and Schenk's model appear similar, alternating in maximum height. SOCET SET has more topographic variability due to its

Quality Test Various Existing dem in Indonesia Toward 10 Meter National dem

NASA Astrophysics Data System (ADS)

Amhar, Fahmi

2016-06-01

Indonesia has various DEM from many sources and various acquisition date spreaded in the past two decades. There are DEM from spaceborne system (Radarsat, TerraSAR-X, ALOS, ASTER-GDEM, SRTM), airborne system (IFSAR, Lidar, aerial photos) and also terrestrial one. The research objective is the quality test and how to extract best DEM in particular area. The method is using differential GPS levelling using geodetic GPS equipment on places which is ensured not changed during past 20 years. The result has shown that DEM from TerraSAR-X and SRTM30 have the best quality (rmse 3.1 m and 3.5 m respectively). Based on this research, it was inferred that these parameters are still positively correlated with the basic concept, namely that the lower and the higher the spatial resolution of a DEM data, the more imprecise the resulting vertical height.

25 Jahre - Institut fuer Geodaesie, Teil 3: Aus dem Leben des Instituts (25 Years - Institute of Geodesy, Part 3: The Life of the Institute)

DTIC Science & Technology

2000-01-01

Kraftwerk Qinshan, VR China 0 1984 bis 1987 Studiumn des Markscheidewesens am Shandong Institute of Mining and Technology, VR China * 1984 bis 1993...die zur Wasserversorgung eines Kraftwerkes der ALCAN dienen sollte. Verbunden mit dem Tunnelprojekt war auch der Bau einer 80 km langen Hoch...spannungsleitung durch unverdorbene Wildnis vom Kraftwerk zur Aluminium-Schmelze in Ki- timat. Zu dieser Zeit war es das gr66Bte hydro-elektrische Projekt, das

Plattenepithelkarzinom in Verbindung mit einer roten Tätowierung.

PubMed

Schmitz, Inge; Prymak, Oleg; Epple, Matthias; Ernert, Carsten; Tannapfel, Andrea

2016-06-01

Obwohl Tätowierungen in den letzten Jahren außerordentlich beliebt geworden sind, wurde in der Literatur bisher nur über wenige Fälle schwerer Reaktionen berichtet, die zu einer malignen Transformation führten. Dies steht im Kontrast zu der praktisch unüberschaubaren Zahl an Tätowierungen weltweit. Die Zusammensetzung der für Tätowierungen verwendeten Farbstoffe variiert stark, und selbst gleiche Farbtöne können unterschiedliche Komponenten enthalten. Das Ziel unserer Studie war es zu untersuchen, auf welche Weise Tätowierungen möglicherweise Hautkrebs auslösen können. Wir berichten über den seltenen Fall einer 24-jährigen Frau, bei der sich sieben Monate nachdem sie eine Tätowierung auf dem Fußrücken erhalten hatte in unmittelbarer Nähe des verwendeten roten Farbstoffs ein Plattenepithelkarzinom entwickelte. Die Komplikationen begannen mit einer unspezifischen Schwellung. Die Läsion wurde histologisch untersucht. Die Zusammensetzung des inkorporierten Farbstoffs wurde mittels Rasterelektronenmikroskopie in Kombination mit energiedispersiver Elementanalyse analysiert. Zur weiteren Charakterisierung wurden Thermogravimetrie und Pulverdiffraktometrie eingesetzt. Der Tätowierungsfarbstoff enthielt hauptsächlich Bariumsulfat; Spuren von Al, S, Ti, P, Mg und Cl ließen sich ebenfalls nachweisen. Bei der Analyse zeigten sich Pigmentgranula unterschiedlicher Größe. In seltenen Fällen kann Tätowierungstinte karzinogene Effekte haben, die multifaktoriell zu sein scheinen. © 2016 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

Kombinierte Hoch-/Niedrig-Dosis-Therapie mit systemischen Glukokor-tikoiden bei schweren Verlaufsformen der Alopecia areata im Kindesalter.

PubMed

Jahn-Bassler, Karin; Bauer, Wolfgang Michael; Karlhofer, Franz; Vossen, Matthias G; Stingl, Georg

2017-01-01

Schwere Verlaufsformen der Alopecia areata (AA) im Kindesalter sind aufgrund limitierter Optionen therapeutisch herausfordernd. Systemische, hochdosierte Glukokortikoide weisen die schnellste Ansprechrate auf, nach dem Absetzen kommt es allerdings zu Rezidiven. Eine längerfristige Hochdosis-Anwendung ist aufgrund der zu erwartenden Nebenwirkungen nicht empfehlenswert. Eine dauerhafte Steroiderhaltungstherapie unterhalb der Cushing-Schwellen-Dosis nach Bolustherapie könnte die Krankheitsaktivität ohne Nebenwirkungen längerfristig unterdrücken. Im Rahmen einer offenen Anwendungsbeobachtung wurden 13 Kinder mit schweren Formen der AA in diese Studie eingeschlossen. Bei sieben Kindern lag eine AA totalis/universalis vor, bei sechs eine multifokale AA mit Befall von mehr als 50 % der Kopfhaut. Das Therapieregime sah eine initiale Prednisolon-Dosierung von 2 mg/kg Körpergeweicht (KG) vor und wurde innerhalb von neun Wochen auf eine Erhaltungsdosierung unter der individuellen Cushing-Schwelle reduziert. Der Nachbeobachtungszeitraum betrug ein bis drei Jahre. Wir beobachteten in 62 % aller Fälle ein komplettes Nachwachsen der Haare. Die mittlere Dauer bis zum Ansprechen lag bei 6,6 Wochen und konnte mit der Erhaltungstherapie über den gesamten Beobachtungszeitraum aufrechterhalten werden. An Nebenwirkungen wurden ausschließlich eine Gewichtszunahme (1-3 kg) bei allen Behandelten sowie eine milde Steroidakne in 23 % der Fälle beobachtet. Die kombinierte Hoch-/Niedrig-Dosis-Therapie mit systemischen Glukokortikoiden mittels Prednisolon zeigte eine hohe, dauerhafte Ansprechrate ohne signifikante Nebenwirkungen. © 2017 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

MIT domain of Vps4 is a Ca2+-dependent phosphoinositide-binding domain.

PubMed

Iwaya, Naoko; Takasu, Hirotoshi; Goda, Natsuko; Shirakawa, Masahiro; Tanaka, Toshiki; Hamada, Daizo; Hiroaki, Hidekazu

2013-05-01

The microtubule interacting and trafficking (MIT) domain is a small protein module that is conserved in proteins of diverged function, such as Vps4, spastin and sorting nexin 15 (SNX15). The molecular function of the MIT domain is protein-protein interaction, in which the domain recognizes peptides containing MIT-interacting motifs. Recently, we identified an evolutionarily related domain, 'variant' MIT domain at the N-terminal region of the microtubule severing enzyme katanin p60. We found that the domain was responsible for binding to microtubules and Ca(2+). Here, we have examined whether the authentic MIT domains also bind Ca(2+). We found that the loop between the first and second α-helices of the MIT domain binds a Ca(2+) ion. Furthermore, the MIT domains derived from Vps4b and SNX15a showed phosphoinositide-binding activities in a Ca(2+)-dependent manner. We propose that the MIT domain is a novel membrane-associating domain involved in endosomal trafficking.

Hydraulic correction method (HCM) to enhance the efficiency of SRTM DEM in flood modeling

NASA Astrophysics Data System (ADS)

Chen, Huili; Liang, Qiuhua; Liu, Yong; Xie, Shuguang

2018-04-01

Digital Elevation Model (DEM) is one of the most important controlling factors determining the simulation accuracy of hydraulic models. However, the currently available global topographic data is confronted with limitations for application in 2-D hydraulic modeling, mainly due to the existence of vegetation bias, random errors and insufficient spatial resolution. A hydraulic correction method (HCM) for the SRTM DEM is proposed in this study to improve modeling accuracy. Firstly, we employ the global vegetation corrected DEM (i.e. Bare-Earth DEM), developed from the SRTM DEM to include both vegetation height and SRTM vegetation signal. Then, a newly released DEM, removing both vegetation bias and random errors (i.e. Multi-Error Removed DEM), is employed to overcome the limitation of height errors. Last, an approach to correct the Multi-Error Removed DEM is presented to account for the insufficiency of spatial resolution, ensuring flow connectivity of the river networks. The approach involves: (a) extracting river networks from the Multi-Error Removed DEM using an automated algorithm in ArcGIS; (b) correcting the location and layout of extracted streams with the aid of Google Earth platform and Remote Sensing imagery; and (c) removing the positive biases of the raised segment in the river networks based on bed slope to generate the hydraulically corrected DEM. The proposed HCM utilizes easily available data and tools to improve the flow connectivity of river networks without manual adjustment. To demonstrate the advantages of HCM, an extreme flood event in Huifa River Basin (China) is simulated on the original DEM, Bare-Earth DEM, Multi-Error removed DEM, and hydraulically corrected DEM using an integrated hydrologic-hydraulic model. A comparative analysis is subsequently performed to assess the simulation accuracy and performance of four different DEMs and favorable results have been obtained on the corrected DEM.

Analyse der pharmazeutischen Versorgungssituation von Patienten mit Psoriasis-Arthritis auf Basis von Routinedaten der Gesetzlichen Krankenversicherung.

PubMed

Sondermann, Wiebke; Ventzke, Julia; Matusiewicz, David; Körber, Andreas

2018-03-01

Die Psoriasis-Arthritis (PsA) gehört zu den chronisch entzündlichen Gelenkerkrankungen. Trotz zahlreicher versorgungswissenschaftlicher Studien in Deutschland liegen zur pharmazeutischen Versorgungssituation von PsA-Patienten bisher kaum aktuelle Ergebnisse vor. Mit Hilfe einer systematischen Literaturrecherche sowie anhand von Routinedaten der Allgemeinen Ortskrankenkasse (AOK) Rheinland/Hamburg wird ein aktueller Überblick über die pharmazeutische Versorgung von PsA-Patienten in Deutschland gegeben. Selektiert wurden Versicherte aus dem ambulanten und stationären Bereich, die im 1. und 2. Quartal des Jahres 2014 die gesicherte Abrechnungsdiagnose Psoriasis-Arthritis L40.5+ aufwiesen. Anschließend wurden auf Basis dieser "vorab definierten" Kohorte die Arzneimitteldaten für 5 Jahre (01.01.2010-31.12.2014) abgerufen. Es konnten insgesamt n  =  3205 Versicherte (45 % männlich, 55 % weiblich) der AOK Rheinland/Hamburg mit einer gesicherten PsA-Diagnose selektiert werden. Das Durchschnittsalter betrug 58,9 Jahre. 53,7 % der PsA-Patienten wurden mit systemischen PsA-relevanten Arzneimitteln versorgt. Nichtsteroidale Antirheumatika (NSAR) wurden am häufigsten verordnet, gefolgt von systemischen Glucocorticoiden. Von den selektierten PsA-Patienten, die eine Systemtherapie erhielten, wurden 72,1 % mittels einer Disease-modifying-antirheumatic-Drug (DMARD)-Monotherapie behandelt, gefolgt von der Kombinationstherapie aus DMARDs und Biologika (20,9 %). Die pharmakologische Therapie der PsA muss eine Gewährleistung zwischen adäquater Versorgung der PsA mit Verhinderung der Krankheitsprogression und ökonomischer Verantwortung darstellen. © 2018 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

PVD-Beschichtungstechnologie

NASA Astrophysics Data System (ADS)

Lake, Markus K.

Die PVD-Technologie umfasst eine Reihe von Beschichtungsverfahren zur Abscheidung von Metallen, Legierungen oder chemischen Verbindungen durch Zufuhr von thermischer Energie oder durch Teilchenbeschuss im Hochvakuum. PVDVerfahren gestatten u. a. die Beschichtung bei niedrigen Prozesstemperaturen, so dass thermisch sensible Substrate, z. B. wärmebehandelte Stähle oder ausgewählte Kunststoffe, beschichtet werden können. Insbesondere mit dem Magnetron Sputter Ion Plating-Verfahren (MSIP-Verfahren) und mit dem Arc Ion Plating-Verfahren (AIP-Verfahren) ist es möglich, thermisch vorbehandelte Werkstoffe zu beschichten, ohne den eingestellten Wärmebehandlungszustand (Härte, Spannungszustand) zu verändern. Ferner können endbearbeitete Bauteile mit der PVD-Technologie beschichtet werden, da die eingesetzten PVD-Verfahren die Ausgangsoberfläche konturgetreu abbilden, ohne dass eine Nachbearbeitung erforderlich wird.

ArcticDEM Validation and Accuracy Assessment

NASA Astrophysics Data System (ADS)

Candela, S. G.; Howat, I.; Noh, M. J.; Porter, C. C.; Morin, P. J.

2017-12-01

ArcticDEM comprises a growing inventory Digital Elevation Models (DEMs) covering all land above 60°N. As of August, 2017, ArcticDEM had openly released 2-m resolution, individual DEM covering over 51 million km2, which includes areas of repeat coverage for change detection, as well as over 15 million km2 of 5-m resolution seamless mosaics. By the end of the project, over 80 million km2 of 2-m DEMs will be produced, averaging four repeats of the 20 million km2 Arctic landmass. ArcticDEM is produced from sub-meter resolution, stereoscopic imagery using open source software (SETSM) on the NCSA Blue Waters supercomputer. These DEMs have known biases of several meters due to errors in the sensor models generated from satellite positioning. These systematic errors are removed through three-dimensional registration to high-precision Lidar or other control datasets. ArcticDEM is registered to seasonally-subsetted ICESat elevations due its global coverage and high report accuracy ( 10 cm). The vertical accuracy of ArcticDEM is then obtained from the statistics of the fit to the ICESat point cloud, which averages -0.01 m ± 0.07 m. ICESat, however, has a relatively coarse measurement footprint ( 70 m) which may impact the precision of the registration. Further, the ICESat data predates the ArcticDEM imagery by a decade, so that temporal changes in the surface may also impact the registration. Finally, biases may exist between different the different sensors in the ArcticDEM constellation. Here we assess the accuracy of ArcticDEM and the ICESat registration through comparison to multiple high-resolution airborne lidar datasets that were acquired within one year of the imagery used in ArcticDEM. We find the ICESat dataset is performing as anticipated, introducing no systematic bias during the coregistration process, and reducing vertical errors to within the uncertainty of the airborne Lidars. Preliminary sensor comparisons show no significant difference post coregistration

[Homöopathisch-phytotherapeutische Behandlung des Reizdarmsyndroms mit Magen-Darm-Entoxin N®: Eine Anwendungsbeobachtung].

PubMed

Märtens, Diane; Range, Natasha; Günnewich, Nils; Gruber, Nicola; Schmidt, Stefan

Hintergrund: In dieser Anwendungsbeobachtung wird zum ersten Mal die Behandlung des Reizdarmsyndroms (RDS) mit einem homöopathisch-phytotherapeutischen Komplexpräparat beschrieben. Methodik: Ziel der 6-wöchigen Therapie mit dem Magen-Darm-Entoxin N® war die Reduzierung der RDS-Symptomatik sowie die Verbesserung der Lebensqualität. Zielkriterien waren die Veränderungen in der Irritable Bowel Syndrome - Severity Scoring System (IBS-SSS) und der Irritable Bowel Syndrome - Quality-of-Life Scale (IBS-QoL). Die Patient/innen (N = 41; Alter 44,0 ± 15,74 Jahre) wurden zu gleichen Teilen in einer Hausarztpraxis (N = 20) und einer Heilpraktikerpraxis (N = 21) rekrutiert. Ergebnisse: Der IBS-QoL-Score verringerte sich signifikant (prä: 35,9 ± 16,3; post: 20,1 ± 13,4; t = 8,504; p < 0,001). Die Effektstärke betrug 1,34 (Cohens d). Der IBS-SSS-Score verringerte sich ebenfalls signifikant (prä: 239,4 ± 83,4; post: 123,7 ± 80,9; t = 7,825; p < 0,001) mit einer Effektstärke von d = 1,24. Die Neben- und Wechselwirkungen waren minimal und signifikante Unterschiede zwischen beiden Praxen wurden nicht gefunden. Schlussfolgerungen: Magen-Darm-Entoxin N® ist eine sichere und sinnvolle Therapieoption bei der Behandlung des RDS. Allerdings sollten randomisierte kontrollierte Studien folgen, um die Spezifizität der Ergebnisse dieser Anwendungsbeobachtung zu stützen. © 2017 S. Karger GmbH, Freiburg.

Hydrologic enforcement of lidar DEMs

USGS Publications Warehouse

Poppenga, Sandra K.; Worstell, Bruce B.; Danielson, Jeffrey J.; Brock, John C.; Evans, Gayla A.; Heidemann, H. Karl

2014-01-01

Hydrologic-enforcement (hydro-enforcement) of light detection and ranging (lidar)-derived digital elevation models (DEMs) modifies the elevations of artificial impediments (such as road fills or railroad grades) to simulate how man-made drainage structures such as culverts or bridges allow continuous downslope flow. Lidar-derived DEMs contain an extremely high level of topographic detail; thus, hydro-enforced lidar-derived DEMs are essential to the U.S. Geological Survey (USGS) for complex modeling of riverine flow. The USGS Coastal and Marine Geology Program (CMGP) is integrating hydro-enforced lidar-derived DEMs (land elevation) and lidar-derived bathymetry (water depth) to enhance storm surge modeling in vulnerable coastal zones.

MIT: Shaping the Future.

ERIC Educational Resources Information Center

Manning, Kenneth R., Ed.

This book provides 16 essays by faculty and staff of the Massachusetts Institute of Technology (MIT) concerning what MIT is like today and offering a guide to its possible future. Emphasis is placed on local, national, and global issues, providing a current sampling of the state of concerns and opinions around MIT. Topics include the question of…

ASTER DEM performance

USGS Publications Warehouse

Fujisada, H.; Bailey, G.B.; Kelly, Glen G.; Hara, S.; Abrams, M.J.

2005-01-01

The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) instrument onboard the National Aeronautics and Space Administration's Terra spacecraft has an along-track stereoscopic capability using its a near-infrared spectral band to acquire the stereo data. ASTER has two telescopes, one for nadir-viewing and another for backward-viewing, with a base-to-height ratio of 0.6. The spatial resolution is 15 m in the horizontal plane. Parameters such as the line-of-sight vectors and the pointing axis were adjusted during the initial operation period to generate Level-1 data products with a high-quality stereo system performance. The evaluation of the digital elevation model (DEM) data was carried out both by Japanese and U.S. science teams separately using different DEM generation software and reference databases. The vertical accuracy of the DEM data generated from the Level-1A data is 20 m with 95% confidence without ground control point (GCP) correction for individual scenes. Geolocation accuracy that is important for the DEM datasets is better than 50 m. This appears to be limited by the spacecraft position accuracy. In addition, a slight increase in accuracy is observed by using GCPs to generate the stereo data.

Feasibility Analysis of DEM Differential Method on Tree Height Assessment wit Terra-SAR/TanDEM-X Data

NASA Astrophysics Data System (ADS)

Zhang, Wangfei; Chen, Erxue; Li, Zengyuan; Feng, Qi; Zhao, Lei

2016-08-01

DEM Differential Method is an effective and efficient way for forest tree height assessment with Polarimetric and interferometric technology, however, the assessment accuracy of it is based on the accuracy of interferometric results and DEM. Terra-SAR/TanDEM-X, which established the first spaceborne bistatic interferometer, can provide highly accurate cross-track interferometric images in the whole global without inherent accuracy limitations like temporal decorrelation and atmospheric disturbance. These characters of Terra-SAR/TandDEM-X give great potential for global or regional tree height assessment, which have been constraint by the temporal decorrelation in traditional repeat-pass interferometry. Currently, in China, it will be costly to collect high accurate DEM with Lidar. At the same time, it is also difficult to get truly representative ground survey samples to test and verify the assessment results. In this paper, we analyzed the feasibility of using TerraSAR/TanDEM-X data to assess forest tree height with current free DEM data like ASTER-GDEM and archived ground in-suit data like forest management inventory data (FMI). At first, the accuracy and of ASTER-GDEM and forest management inventory data had been assessment according to the DEM and canopy height model (CHM) extracted from Lidar data. The results show the average elevation RMSE between ASTER-GEDM and Lidar-DEM is about 13 meters, but they have high correlation with the correlation coefficient of 0.96. With a linear regression model, we can compensate ASTER-GDEM and improve its accuracy nearly to the Lidar-DEM with same scale. The correlation coefficient between FMI and CHM is 0.40. its accuracy is able to be improved by a linear regression model withinconfidence intervals of 95%. After compensation of ASTER-GDEM and FMI, we calculated the tree height in Mengla test site with DEM Differential Method. The results showed that the corrected ASTER-GDEM can effectively improve the assessment accuracy

Computerunterstütztes Modellieren mit Musiknetzen

NASA Astrophysics Data System (ADS)

Levens, Ulla

In der folgenden Ausführung geht es um eine Anwendung von Petri-Netzen im Bereich Musik. Ausgehend von der Implementierung einer speziellen Anwendung, dem Programmsystem ScoreSynth, wird das zugrundeliegende Konzept erläutert und anschließend an einem kleinen Beispiel veranschaulicht. Dieser Beitrag ist ein Auszug aus [Lev95b].

Elektroakustische Wandler

NASA Astrophysics Data System (ADS)

Plaßmann, Wilfried

Um Sprache und Musik über größere Entfernungen zu übertragen, wird der Hörschall mit einem Mikrofon in ein proportionales elektrisches Signal umgewandelt und auf drahtlosem Wege (Beispiel Rundfunkübertragung) oder drahtgebunden (Beispiel Telefon, Kabelrundfunk, oft in Kombination mit dem drahtlosen Weg) zum Empfänger übermittelt. Am Empfangsort setzt z. B. ein Lautsprecher das elektrische Signal wieder in ein akustisches Signal um.

Small catchments DEM creation using Unmanned Aerial Vehicles

NASA Astrophysics Data System (ADS)

Gafurov, A. M.

2018-01-01

Digital elevation models (DEM) are an important source of information on the terrain, allowing researchers to evaluate various exogenous processes. The higher the accuracy of DEM the better the level of the work possible. An important source of data for the construction of DEMs are point clouds obtained with terrestrial laser scanning (TLS) and unmanned aerial vehicles (UAV). In this paper, we present the results of constructing a DEM on small catchments using UAVs. Estimation of the UAV DEM showed comparable accuracy with the TLS if real time kinematic Global Positioning System (RTK-GPS) ground control points (GCPs) and check points (CPs) were used. In this case, the main source of errors in the construction of DEMs are the errors in the referencing of survey results.

Evaluation of TanDEM-X DEMs on selected Brazilian sites: Comparison with SRTM, ASTER GDEM and ALOS AW3D30

NASA Astrophysics Data System (ADS)

Grohmann, Carlos H.

2018-06-01

A first assessment of the TanDEM-X DEMs over Brazilian territory is presented through a comparison with SRTM, ASTER GDEM and ALOS AW3D30 DEMs in seven study areas with distinct geomorphological contexts, vegetation coverage and land use. Visual analysis and elevation histograms point to a finer effective spatial resolution of TanDEM-X compared to SRTM and ASTER GDEM. In areas of open vegetation, TanDEM-X lower elevations indicate a better penetration of the radar signal. DEMs of differences (DoDs) allowed the identification of issues inherent to the production methods of the analyzed DEMs, such as mast oscillations in SRTM data and mismatch between adjacent scenes in ASTER GDEM and ALOS AW3D30. A systematic difference in elevations between TanDEM-X 12m, TanDEM-X 30m and SRTM was observed in the steep slopes of the coastal ranges, related to the moving-window process used to resample the 12m data to a 30m pixel size. Due its simplicity, it is strongly recommended to produce a DoD with SRTM before using ASTER GDEM or ALOS AW3D30 in any analysis, to evaluate if the area of interest is affected by these problems. The DoDs also highlighted changes in land use in the time span between the acquisition of SRTM (2000) and TanDEM-X (2013) data, whether by natural causes or by human interference in the environment.

Biotechnology Process Engineering Center at MIT Home

Science.gov Websites

Research Summary Research Details of Project A (Stem Cell Vehicle Subthrust) and Project B (Targeted ) 253-0805 | Facsimile (617) 253-2400 | e-mail: bpec-www@mit.edu Current NSF ERC-Supported Research Vehicle Subthrust) Other Projects Related to NSF-Funded Research (coming soon) Home | People | Education

Pulse fracture simulation in shale rock reservoirs: DEM and FEM-DEM approaches

NASA Astrophysics Data System (ADS)

González, José Manuel; Zárate, Francisco; Oñate, Eugenio

2018-07-01

In this paper we analyze the capabilities of two numerical techniques based on DEM and FEM-DEM approaches for the simulation of fracture in shale rock caused by a pulse of pressure. We have studied the evolution of fracture in several fracture scenarios related to the initial stress state in the soil or the pressure pulse peak. Fracture length and type of failure have been taken as reference for validating the models. The results obtained show a good approximation to FEM results from the literature.

Bathymetric survey of water reservoirs in north-eastern Brazil based on TanDEM-X satellite data.

PubMed

Zhang, Shuping; Foerster, Saskia; Medeiros, Pedro; de Araújo, José Carlos; Motagh, Mahdi; Waske, Bjoern

2016-11-15

Water scarcity in the dry season is a vital problem in dryland regions such as northeastern Brazil. Water supplies in these areas often come from numerous reservoirs of various sizes. However, inventory data for these reservoirs is often limited due to the expense and time required for their acquisition via field surveys, particularly in remote areas. Remote sensing techniques provide a valuable alternative to conventional reservoir bathymetric surveys for water resource management. In this study single pass TanDEM-X data acquired in bistatic mode were used to generate digital elevation models (DEMs) in the Madalena catchment, northeastern Brazil. Validation with differential global positioning system (DGPS) data from field measurements indicated an absolute elevation accuracy of approximately 1m for the TanDEM-X derived DEMs (TDX DEMs). The DEMs derived from TanDEM-X data acquired at low water levels show significant advantages over bathymetric maps derived from field survey, particularly with regard to coverage, evenly distributed measurements and replication of reservoir shape. Furthermore, by mapping the dry reservoir bottoms with TanDEM-X data, TDX DEMs are free of emergent and submerged macrophytes, independent of water depth (e.g. >10m), water quality and even weather conditions. Thus, the method is superior to other existing bathymetric mapping approaches, particularly for inland water bodies. The proposed approach relies on (nearly) dry reservoir conditions at times of image acquisition and is thus restricted to areas that show considerable water levels variations. However, comparisons between TDX DEM and the bathymetric map derived from field surveys show that the amount of water retained during the dry phase has only marginal impact on the total water volume derivation from TDX DEM. Overall, DEMs generated from bistatic TanDEM-X data acquired in low water periods constitute a useful and efficient data source for deriving reservoir bathymetry and show

Estimating Coastal Digital Elevation Model (DEM) Uncertainty

NASA Astrophysics Data System (ADS)

Amante, C.; Mesick, S.

2017-12-01

Integrated bathymetric-topographic digital elevation models (DEMs) are representations of the Earth's solid surface and are fundamental to the modeling of coastal processes, including tsunami, storm surge, and sea-level rise inundation. Deviations in elevation values from the actual seabed or land surface constitute errors in DEMs, which originate from numerous sources, including: (i) the source elevation measurements (e.g., multibeam sonar, lidar), (ii) the interpolative gridding technique (e.g., spline, kriging) used to estimate elevations in areas unconstrained by source measurements, and (iii) the datum transformation used to convert bathymetric and topographic data to common vertical reference systems. The magnitude and spatial distribution of the errors from these sources are typically unknown, and the lack of knowledge regarding these errors represents the vertical uncertainty in the DEM. The National Oceanic and Atmospheric Administration (NOAA) National Centers for Environmental Information (NCEI) has developed DEMs for more than 200 coastal communities. This study presents a methodology developed at NOAA NCEI to derive accompanying uncertainty surfaces that estimate DEM errors at the individual cell-level. The development of high-resolution (1/9th arc-second), integrated bathymetric-topographic DEMs along the southwest coast of Florida serves as the case study for deriving uncertainty surfaces. The estimated uncertainty can then be propagated into the modeling of coastal processes that utilize DEMs. Incorporating the uncertainty produces more reliable modeling results, and in turn, better-informed coastal management decisions.

Radar and Lidar Radar DEM

NASA Technical Reports Server (NTRS)

Liskovich, Diana; Simard, Marc

2011-01-01

Using radar and lidar data, the aim is to improve 3D rendering of terrain, including digital elevation models (DEM) and estimates of vegetation height and biomass in a variety of forest types and terrains. The 3D mapping of vegetation structure and the analysis are useful to determine the role of forest in climate change (carbon cycle), in providing habitat and as a provider of socio-economic services. This in turn will lead to potential for development of more effective land-use management. The first part of the project was to characterize the Shuttle Radar Topography Mission DEM error with respect to ICESat/GLAS point estimates of elevation. We investigated potential trends with latitude, canopy height, signal to noise ratio (SNR), number of LiDAR waveform peaks, and maximum peak width. Scatter plots were produced for each variable and were fitted with 1st and 2nd degree polynomials. Higher order trends were visually inspected through filtering with a mean and median filter. We also assessed trends in the DEM error variance. Finally, a map showing how DEM error was geographically distributed globally was created.

A combined multi-interferogram algorithm for high resolution DEM reconstruction over deformed regions with TerraSAR-X data

NASA Astrophysics Data System (ADS)

Zhao, Chaoying; Qu, Feifei; Zhang, Qin; Zhu, Wu

2012-10-01

The accuracy of DEM generated with interferometric synthetic aperture radar (InSAR) technique mostly depends on phase unwrapping errors, atmospheric effects, baseline errors and phase noise. The first term is more serious if the high-resolution TerraSAR-X data over urban regions and mountainous regions are applied. In addition, the deformation effect cannot be neglected if the study regions are suffering from surface deformation within the SAR acquisition dates. In this paper, several measures have been taken to generate high resolution DEM over urban regions and mountainous regions with TerraSAR data. The SAR interferometric pairs are divided into two subsets: (a) DEM subsets and (b) deformation subsets. These two interferometric sets serve to generate DEM and deformation, respectively. The external DEM is applied to assist the phase unwrapping with "remove-restore" procedure. The deformation phase is re-scaled and subtracted from each DEM observations. Lastly, the stochastic errors including atmospheric effects and phase noise are suppressed by averaging heights from several interferograms with weights. Six TerraSAR-X data are applied to generate a 6-m-resolution DEM over Xi'an, China using these procedures. Both discrete GPS heights and local high resolution and high precision DEM data are applied to calibrate the DEM generated with our algorithm, and around 4.1 m precision is achieved.

High-resolution DEM Effects on Geophysical Flow Models

NASA Astrophysics Data System (ADS)

Williams, M. R.; Bursik, M. I.; Stefanescu, R. E. R.; Patra, A. K.

2014-12-01

Geophysical mass flow models are numerical models that approximate pyroclastic flow events and can be used to assess the volcanic hazards certain areas may face. One such model, TITAN2D, approximates granular-flow physics based on a depth-averaged analytical model using inputs of basal and internal friction, material volume at a coordinate point, and a GIS in the form of a digital elevation model (DEM). The volume of modeled material propagates over the DEM in a way that is governed by the slope and curvature of the DEM surface and the basal and internal friction angles. Results from TITAN2D are highly dependent upon the inputs to the model. Here we focus on a single input: the DEM, which can vary in resolution. High resolution DEMs are advantageous in that they contain more surface details than lower-resolution models, presumably allowing modeled flows to propagate in a way more true to the real surface. However, very high resolution DEMs can create undesirable artifacts in the slope and curvature that corrupt flow calculations. With high-resolution DEMs becoming more widely available and preferable for use, determining the point at which high resolution data is less advantageous compared to lower resolution data becomes important. We find that in cases of high resolution, integer-valued DEMs, very high-resolution is detrimental to good model outputs when moderate-to-low (<10-15°) slope angles are involved. At these slope angles, multiple adjacent DEM cell elevation values are equal due to the need for the DEM to approximate the low slope with a limited set of integer values for elevation. The first derivative of the elevation surface thus becomes zero. In these cases, flow propagation is inhibited by these spurious zero-slope conditions. Here we present evidence for this "terracing effect" from 1) a mathematically defined simulated elevation model, to demonstrate the terracing effects of integer valued data, and 2) a real-world DEM where terracing must be

Construction of pixel-level resolution DEMs from monocular images by shape and albedo from shading constrained with low-resolution DEM

NASA Astrophysics Data System (ADS)

Wu, Bo; Liu, Wai Chung; Grumpe, Arne; Wöhler, Christian

2018-06-01

Lunar Digital Elevation Model (DEM) is important for lunar successful landing and exploration missions. Lunar DEMs are typically generated by photogrammetry or laser altimetry approaches. Photogrammetric methods require multiple stereo images of the region of interest and it may not be applicable in cases where stereo coverage is not available. In contrast, reflectance based shape reconstruction techniques, such as shape from shading (SfS) and shape and albedo from shading (SAfS), apply monocular images to generate DEMs with pixel-level resolution. We present a novel hierarchical SAfS method that refines a lower-resolution DEM to pixel-level resolution given a monocular image with known light source. We also estimate the corresponding pixel-wise albedo map in the process and based on that to regularize the shape reconstruction with pixel-level resolution based on the low-resolution DEM. In this study, a Lunar-Lambertian reflectance model is applied to estimate the albedo map. Experiments were carried out using monocular images from the Lunar Reconnaissance Orbiter Narrow Angle Camera (LRO NAC), with spatial resolution of 0.5-1.5 m per pixel, constrained by the Selenological and Engineering Explorer and LRO Elevation Model (SLDEM), with spatial resolution of 60 m. The results indicate that local details are well recovered by the proposed algorithm with plausible albedo estimation. The low-frequency topographic consistency depends on the quality of low-resolution DEM and the resolution difference between the image and the low-resolution DEM.

A coupled DEM-CFD method for impulse wave modelling

NASA Astrophysics Data System (ADS)

Zhao, Tao; Utili, Stefano; Crosta, GiovanBattista

2015-04-01

investigated by Crosta et al. (2014) via 2D and 3D FEM ALE modelling without considering the water seepage in the slope mass has been used. Their results can be a good way to estimate the slope and wave motion for fast sliding conditions. The 3D modelling can also clarify the lateral motion of water and estimate the potential risk of water overtopping the dam crest. The DEM and FEM ALE modelling can be used together to analyse fast moving rockslides (i.e. flowslides, rockslides, rock and debris avalanches) both in dry conditions and for their interaction with water basins. References Zhao, T., Utili, S., Crosta, G.B. Rockslide and impulse wave modelling in the Vajont reservoir by DEM-CFD analyses. Rock Mechanics and rock Engineering, under review. Crosta, G.B., Imposimato, S. & Roddeman, D. 2014. Landslide spreading, impulse waves and modelling of the Vajont rockslide. Rock Mechanics and Rock Engineering, under review.

The Importance of Precise Digital Elevation Models (DEM) in Modelling Floods

NASA Astrophysics Data System (ADS)

Demir, Gokben; Akyurek, Zuhal

2016-04-01

Digital elevation Models (DEM) are important inputs for topography for the accurate modelling of floodplain hydrodynamics. Floodplains have a key role as natural retarding pools which attenuate flood waves and suppress flood peaks. GPS, LIDAR and bathymetric surveys are well known surveying methods to acquire topographic data. It is not only time consuming and expensive to obtain topographic data through surveying but also sometimes impossible for remote areas. In this study it is aimed to present the importance of accurate modelling of topography for flood modelling. The flood modelling for Samsun-Terme in Blacksea region of Turkey is done. One of the DEM is obtained from the point observations retrieved from 1/5000 scaled orthophotos and 1/1000 scaled point elevation data from field surveys at x-sections. The river banks are corrected by using the orthophotos and elevation values. This DEM is named as scaled DEM. The other DEM is obtained from bathymetric surveys. 296 538 number of points and the left/right bank slopes were used to construct the DEM having 1 m spatial resolution and this DEM is named as base DEM. Two DEMs were compared by using 27 x-sections. The maximum difference at thalweg of the river bed is 2m and the minimum difference is 20 cm between two DEMs. The channel conveyance capacity in base DEM is larger than the one in scaled DEM and floodplain is modelled in detail in base DEM. MIKE21 with flexible grid is used in 2- dimensional shallow water flow modelling. The model by using two DEMs were calibrated for a flood event (July 9, 2012). The roughness is considered as the calibration parameter. From comparison of input hydrograph at the upstream of the river and output hydrograph at the downstream of the river, the attenuation is obtained as 91% and 84% for the base DEM and scaled DEM, respectively. The time lag in hydrographs does not show any difference for two DEMs and it is obtained as 3 hours. Maximum flood extents differ for the two DEMs

The Coordinate Transformation Method of High Resolution dem Data

NASA Astrophysics Data System (ADS)

Yan, Chaode; Guo, Wang; Li, Aimin

2018-04-01

Coordinate transformation methods of DEM data can be divided into two categories. One reconstruct based on original vector elevation data. The other transforms DEM data blocks by transforming parameters. But the former doesn't work in the absence of original vector data, and the later may cause errors at joint places between adjoining blocks of high resolution DEM data. In view of this problem, a method dealing with high resolution DEM data coordinate transformation is proposed. The method transforms DEM data into discrete vector elevation points, and then adjusts positions of points by bi-linear interpolation respectively. Finally, a TIN is generated by transformed points, and the new DEM data in target coordinate system is reconstructed based on TIN. An algorithm which can find blocks and transform automatically is given in this paper. The method is tested in different terrains and proved to be feasible and valid.

BlazeDEM3D-GPU A Large Scale DEM simulation code for GPUs

NASA Astrophysics Data System (ADS)

Govender, Nicolin; Wilke, Daniel; Pizette, Patrick; Khinast, Johannes

2017-06-01

Accurately predicting the dynamics of particulate materials is of importance to numerous scientific and industrial areas with applications ranging across particle scales from powder flow to ore crushing. Computational discrete element simulations is a viable option to aid in the understanding of particulate dynamics and design of devices such as mixers, silos and ball mills, as laboratory scale tests comes at a significant cost. However, the computational time required to simulate an industrial scale simulation which consists of tens of millions of particles can take months to complete on large CPU clusters, making the Discrete Element Method (DEM) unfeasible for industrial applications. Simulations are therefore typically restricted to tens of thousands of particles with highly detailed particle shapes or a few million of particles with often oversimplified particle shapes. However, a number of applications require accurate representation of the particle shape to capture the macroscopic behaviour of the particulate system. In this paper we give an overview of the recent extensions to the open source GPU based DEM code, BlazeDEM3D-GPU, that can simulate millions of polyhedra and tens of millions of spheres on a desktop computer with a single or multiple GPUs.

Grundlagen der Nachrichtenübertragung

NASA Astrophysics Data System (ADS)

Plaßmann, Wilfried

Die Nachrichtentechnik hat die Aufgabe, Nachrichten auszutauschen. Nachrichten sind z. B. Fragen, Beobachtungen und Befehle. Unter dem Begriff Nachrichtenübertragung wird hier die elektrische Nachrichtenübertragung verstanden, denn zur Übermittlung von Nachrichten werden Spannungen und Ströme sowie elektrische und magnetische Felder eingesetzt. Die Übertragung beginnt mit der Nachrichtenquelle, die die Nachrichten aussendet, und endet mit der Nachrichtensenke, die sie empfängt. Zwischen beiden liegt das elektrische Nachrichtenübertragungssystem, dessen Funktionseinheiten dargestellt sind und erläutert werden.

Assessment of Reference Height Models on Quality of Tandem-X dem

NASA Astrophysics Data System (ADS)

Mirzaee, S.; Motagh, M.; Arefi, H.

2015-12-01

The aim of this study is to investigate the effect of various Global Digital Elevation Models (GDEMs) in producing high-resolution topography model using TanDEM-X (TDX) Coregistered Single Look Slant Range Complex (CoSSC) images. We selected an image acquired on Jun 12th, 2012 over Doroud region in Lorestan, west of Iran and used 4 external digital elevation models in our processing including DLR/ASI X-SAR DEM (SRTM-X, 30m resolution), ASTER GDEM Version 2 (ASTER-GDEMV2, 30m resolution), NASA SRTM Version 4 (SRTM-V4, 90m resolution), and a local photogrammetry-based DEM prepared by National Cartographic Center (NCC DEM, 10m resolution) of Iran. InSAR procedure for DEM generation was repeated four times with each of the four external height references. The quality of each external DEM was initially assessed using ICESat filtered points. Then, the quality of, each TDX-based DEM was assessed using the more precise external DEM selected in the previous step. Results showed that both local (NCC) DEM and SRTM X-band performed the best (RMSE< 9m) for TDX-DEM generation. In contrast, ASTER GDEM v2 and SRTM C-band v4 showed poorer quality.

Estimating River Surface Elevation From ArcticDEM

NASA Astrophysics Data System (ADS)

Dai, Chunli; Durand, Michael; Howat, Ian M.; Altenau, Elizabeth H.; Pavelsky, Tamlin M.

2018-04-01

ArcticDEM is a collection of 2-m resolution, repeat digital surface models created from stereoscopic satellite imagery. To demonstrate the potential of ArcticDEM for measuring river stages and discharges, we estimate river surface heights along a reach of Tanana River near Fairbanks, Alaska, by the precise detection of river shorelines and mapping of shorelines to land surface elevation. The river height profiles over a 15-km reach agree with in situ measurements to a standard deviation less than 30 cm. The time series of ArcticDEM-derived river heights agree with the U.S. Geological Survey gage measurements with a standard deviation of 32 cm. Using the rating curve for that gage, we obtain discharges with a validation accuracy (root-mean-square error) of 234 m3/s (23% of the mean discharge). Our results demonstrate that ArcticDEM can accurately measure spatial and temporal variations of river surfaces, providing a new and powerful data set for hydrologic analysis.

EMDataBank unified data resource for 3DEM.

PubMed

Lawson, Catherine L; Patwardhan, Ardan; Baker, Matthew L; Hryc, Corey; Garcia, Eduardo Sanz; Hudson, Brian P; Lagerstedt, Ingvar; Ludtke, Steven J; Pintilie, Grigore; Sala, Raul; Westbrook, John D; Berman, Helen M; Kleywegt, Gerard J; Chiu, Wah

2016-01-04

Three-dimensional Electron Microscopy (3DEM) has become a key experimental method in structural biology for a broad spectrum of biological specimens from molecules to cells. The EMDataBank project provides a unified portal for deposition, retrieval and analysis of 3DEM density maps, atomic models and associated metadata (emdatabank.org). We provide here an overview of the rapidly growing 3DEM structural data archives, which include maps in EM Data Bank and map-derived models in the Protein Data Bank. In addition, we describe progress and approaches toward development of validation protocols and methods, working with the scientific community, in order to create a validation pipeline for 3DEM data. © The Author(s) 2015. Published by Oxford University Press on behalf of Nucleic Acids Research.

[Kombinierte Anwendung von Strahlentherapie und adjuvanter Therapie mit einem Mistelextrakt (Viscum album L.) zur Behandlung des oralen malignen Melanoms beim Hund: Eine retrospektive Studie].

PubMed

von Bodungen, Uta; Ruess, Katja; Reif, Marcus; Biegel, Ulrike

2017-01-01

Hintergrund: Orale maligne Melanome (OMM) des Hundes zeichnen sich durch schnelles Wachstum, lokale Invasion und hohe Metastasierungsraten aus. Extrakte auf Basis von Viscum album L. (VAE) werden zunehmend in der Krebstherapie sowohl in der Human- als auch in der Veterinärmedizin eingesetzt. Ziel unserer Studie war es zu untersuchen, inwieweit die adjuvante Therapie mit VAE eine therapeutische Option zur Behandlung von OMM ist. Besonderes Augenmerk galt dabei der Überlebenszeit und möglichen Nebenwirkungen. Tiere und Methoden: 26 Hunde mit OMM, die in einem der größten veterinäronkologischen Zentren der Schweiz allesamt eine Strahlentherapie erhielten (teilweise nach operativer Tumorresektion) wurden in die retrospektive Studie eingeschlossen: 18 Hunde wurden mit VAE behandelt (1 ml VAE (Iscador®) in ansteigenden Konzentrationen von 0,1 bis 20 mg/ml subkutan 3-mal pro Woche (VAE-Gruppe), 8 erhielten keine adjuvante Behandlung (Vergleichsgruppe). Wir verglichen die Größenentwicklung der OMM sowie die Überlebenszeit. Ergebnisse: Patienten mit Bestrahlung und adjuvanter VAE-Therapie zeigten mit 236 Tagen eine signifikant längere mediane Überlebenszeit im Vergleich zu Patienten mit Bestrahlung, aber ohne adjuvante VAE-Therapie (49 Tage; Log-Rank-Test: p = 0,0047). Die VAE-Therapie verlängerte die Überlebenszeit um mehr als zwei Drittel (Hazard Ratio (HR) = 0,30, 95%-Konfidenzintervall (KI) 0,11-0,86; p = 0,024), während ein höheres Tumorstadium gemäß UICC (Union internationale contre le cancer) einen statistischen Trend zur Verdopplung des Sterberisikos zeigte (UICC-Stadium III/IV vs. I/II: HR = 2,12, 95%-KI 0,88-5,12; p = 0,095). Zwei Patienten zeigten milde Nebenwirkungen während der VAE-Behandlung. Einer der beiden zeigte 1 Tag lang ein selbstlimitiertes Fieber, bei dem anderen Patienten reduzierten wir die Dosis von einem konzentrierteren zu einem weniger konzentrierten VAE (Serie 0) aufgrund von Müdigkeit, die daraufhin verschwand

Clinical accuracy of inflationary oscillometry in pregnancy and pre-eclampsia: Omron-MIT Elite.

PubMed

Chung, Y; Brochut, M C; de Greeff, A; Shennan, A H

2012-10-01

To evaluate the accuracy of the Omron MIT Elite in pregnancy and pre-eclampsia according to the British Hypertension Society protocol (BHS). Prospective observational study. Antenatal clinics and wards at St. Thomas' Hospital (London, UK). Forty-five pregnant women including 15 with pre-eclampsia. Nine sequential same arm blood pressure (BP) measurements were taken from each woman by trained observers, alternating between mercury sphygmomanometry and the test device. Grading criteria of the BHS protocol (A/B grade=pass; C/D=fail). The Omron MIT Elite achieved a grade A/A in both pregnancy and pre-eclampsia. The mean difference (SD) between the mercury standard and the device in pregnancy was -1.1 (5.2)mmHg and 1.5 (4.8)mmHg for systolic and diastolic BP respectively compared to 0.2 (5.3)mmHg and 2.2 (5.5)mmHg in pre-eclampsia. The Omron MIT Elite can be recommended for use in pregnancy and pre-eclampsia according to the BHS protocol. To date, this is the most accurate automated BP device validated in pre-eclampsia. Copyright © 2012. Published by Elsevier B.V.

Coupling photogrammetric data with DFN-DEM model for rock slope hazard assessment

NASA Astrophysics Data System (ADS)

Donze, Frederic; Scholtes, Luc; Bonilla-Sierra, Viviana; Elmouttie, Marc

2013-04-01

Structural and mechanical analyses of rock mass are key components for rock slope stability assessment. The complementary use of photogrammetric techniques [Poropat, 2001] and coupled DFN-DEM models [Harthong et al., 2012] provides a methodology that can be applied to complex 3D configurations. DFN-DEM formulation [Scholtès & Donzé, 2012a,b] has been chosen for modeling since it can explicitly take into account the fracture sets. Analyses conducted in 3D can produce very complex and unintuitive failure mechanisms. Therefore, a modeling strategy must be established in order to identify the key features which control the stability. For this purpose, a realistic case is presented to show the overall methodology from the photogrammetry acquisition to the mechanical modeling. By combining Sirovision and YADE Open DEM [Kozicki & Donzé, 2008, 2009], it can be shown that even for large camera to rock slope ranges (tested about one kilometer), the accuracy of the data are sufficient to assess the role of the structures on the stability of a jointed rock slope. In this case, on site stereo pairs of 2D images were taken to create 3D surface models. Then, digital identification of structural features on the unstable block zone was processed with Sirojoint software [Sirovision, 2010]. After acquiring the numerical topography, the 3D digitalized and meshed surface was imported into the YADE Open DEM platform to define the studied rock mass as a closed (manifold) volume to define the bounding volume for numerical modeling. The discontinuities were then imported as meshed planar elliptic surfaces into the model. The model was then submitted to gravity loading. During this step, high values of cohesion were assigned to the discontinuities in order to avoid failure or block displacements triggered by inertial effects. To assess the respective role of the pre-existing discontinuities in the block stability, different configurations have been tested as well as different degree of

Stochastic noise characteristics in matrix inversion tomosynthesis (MITS).

PubMed

Godfrey, Devon J; McAdams, H P; Dobbins, James T Third

2009-05-01

Matrix inversion tomosynthesis (MITS) uses known imaging geometry and linear systems theory to deterministically separate in-plane detail from residual tomographic blur in a set of conventional tomosynthesis ("shift-and-add") planes. A previous investigation explored the effect of scan angle (ANG), number of projections (N), and number of reconstructed planes (NP) on the MITS impulse response and modulation transfer function characteristics, and concluded that ANG = 20 degrees, N = 71, and NP = 69 is the optimal MITS imaging technique for chest imaging on our prototype tomosynthesis system. This article examines the effect of ANG, N, and NP on the MITS exposure-normalized noise power spectra (ENNPS) and seeks to confirm that the imaging parameters selected previously by an analysis of the MITS impulse response also yield reasonable stochastic properties in MITS reconstructed planes. ENNPS curves were generated for experimentally acquired mean-subtracted projection images, conventional tomosynthesis planes, and MITS planes with varying combinations of the parameters ANG, N, and NP. Image data were collected using a prototype tomosynthesis system, with 11.4 cm acrylic placed near the image receptor to produce lung-equivalent beam hardening and scattered radiation. Ten identically acquired tomosynthesis data sets (realizations) were collected for each selected technique and used to generate ensemble mean images that were subtracted from individual image realizations prior to noise power spectra (NPS) estimation. NPS curves were normalized to account for differences in entrance exposure (as measured with an ion chamber), yielding estimates of the ENNPS for each technique. Results suggest that mid- and high-frequency noise in MITS planes is fairly equivalent in magnitude to noise in conventional tomosynthesis planes, but low-frequency noise is amplified in the most anterior and posterior reconstruction planes. Selecting the largest available number of projections (N

Wirksamkeit und Sicherheit von Fumarsäureestern in Kombination mit Phototherapie bei Patienten mit moderater bis schwerer Plaque-Psoriasis (FAST).

PubMed

Weisenseel, Peter; Reich, Kristian; Griemberg, Wiebke; Merten, Katharina; Gröschel, Christine; Gomez, Natalie Nunez; Taipale, Kirsi; Bräu, Beate; Zschocke, Ina

2017-02-01

Die Behandlung von Psoriasis-Patienten mit einer Kombination aus Fumarsäureestern (FSE, Fumaderm ® ) und Phototherapie (UV) ist verbreitet, wurde aber im Rahmen von Studien wenig untersucht. Bisher liegen lediglich Daten aus einer kleinen Pilotstudie vor. Intention dieser Studie war, eine FSE/UV-Kombinationsbehandlung an einem größeren Patientenkollektiv mit mittelschwerer bis schwerer Psoriasis zu untersuchen. In dieser prospektiven, multizentrischen, nichtinterventionellen Studie wurden Daten von Patienten mit FSE/UV-Kombinationstherapie hinsichtlich der Wirksamkeit (PGA' PASI, DLQI, EQ-5D), Sicherheit und Dosierung über einen Zeitraum von zwölf Monaten erfasst und mit Daten einer retrospektiven Studie mit FSE-Monotherapie verglichen. Es wurden Daten von 363 Patienten ausgewertet. Unter der Kombinationstherapie verbesserten sich alle Wirksamkeitsparameter deutlich. Im Vergleich zur Monotherapie mit FSE konnte durch die Kombination mit UV ein schnellerer Wirkeintritt erzielt werden, wobei nach zwölf Monaten kein Unterschied in der Wirksamkeit bestand. Die Dauer und Art der Phototherapie zeigte keinen Einfluss auf die Wirksamkeitsparameter. Allgemein wurde die Kombinationstherapie gut vertragen. Unerwünschte Ereignisse wurden bei 7 % der Patienten berichtet. Die FSE/UV Kombinationstherapie zeigt eine gute Wirksamkeit und Verträglichkeit und kann zu einem schnelleren Wirkeintritt führen. Eine Kombinationstherapie erscheint vor allem in den ersten drei Monaten der FSE Behandlung sinnvoll. © 2017 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

Preliminary GAOFEN-3 Insar dem Accuracy Analysis

NASA Astrophysics Data System (ADS)

Chen, Q.; Li, T.; Tang, X.; Gao, X.; Zhang, X.

2018-04-01

GF-3 satellite, the first C band and full-polarization SAR satellite of China with spatial resolution of 1 m, was successfully launched in August 2016. We analyze the error sources of GF-3 satellite in this paper, and provide the interferometric calibration model based on range function, Doppler shift equation and interferometric phase function, and interferometric parameters calibrated using the three-dimensional coordinates of ground control points. Then, we conduct the experimental two pairs of images in fine stripmap I mode covering Songshan of Henan Province and Tangshan of Hebei Province, respectively. The DEM data are assessed using SRTM DEM, ICESat-GLAS points, and ground control points database obtained using ZY-3 satellite to validate the accuracy of DEM elevation. The experimental results show that the accuracy of DEM extracted from GF-3 satellite SAR data can meet the requirements of topographic mapping in mountain and alpine regions at the scale of 1 : 50000 in China. Besides, it proves that GF-3 satellite has the potential of interferometry.

Shuttle radar DEM hydrological correction for erosion modelling in small catchments

NASA Astrophysics Data System (ADS)

Jarihani, Ben; Sidle, Roy; Bartley, Rebecca

2016-04-01

Digital Elevation Models (DEMs) that accurately replicate both landscape form and processes are critical to support modelling of environmental processes. Catchment and hillslope scale runoff and sediment processes (i.e., patterns of overland flow, infiltration, subsurface stormflow and erosion) are all topographically mediated. In remote and data-scarce regions, high resolution DEMs (LiDAR) are often not available, and moderate to course resolution digital elevation models (e.g., SRTM) have difficulty replicating detailed hydrological patterns, especially in relatively flat landscapes. Several surface reconditioning algorithms (e.g., Smoothing) and "Stream burning" techniques (e.g., Agree or ANUDEM), in conjunction with representation of the known stream networks, have been used to improve DEM performance in replicating known hydrology. Detailed stream network data are not available at regional and national scales, but can be derived at local scales from remotely-sensed data. This research explores the implication of high resolution stream network data derived from Google Earth images for DEM hydrological correction, instead of using course resolution stream networks derived from topographic maps. The accuracy of implemented method in producing hydrological-efficient DEMs were assessed by comparing the hydrological parameters derived from modified DEMs and limited high-resolution airborne LiDAR DEMs. The degree of modification is dominated by the method used and availability of the stream network data. Although stream burning techniques improve DEMs hydrologically, these techniques alter DEM characteristics that may affect catchment boundaries, stream position and length, as well as secondary terrain derivatives (e.g., slope, aspect). Modification of a DEM to better reflect known hydrology can be useful, however, knowledge of the magnitude and spatial pattern of the changes are required before using a DEM for subsequent analyses.

Qualität auf dem Prüfstand

NASA Astrophysics Data System (ADS)

Michaelis, Michael

An einem Wochenende im Dezember 2009 beendete der chinesische Eisenbahn-Vizeminister Hu Yadong in Begleitung einer hochrangigen Delegation aus Experten des Department of Safety seines Ministeriums eine mehrtägige Europareise mit einem Besuch in der Konzernzentrale des weltweit führenden Herstellers von Bremssystemen für Schienen- und Nutzfahrzeuge in München. Schon in wenigen Jahren wird China über die weltweit größte Flotte an Hochgeschwindigkeitszügen verfügen und dabei sind Sicherheit und Qualität vorrangige Anforderungen. Knorr-Bremse liefert 100% der Bremsanlagen dieser Züge und hat vor kurzem mit rund 500 Millionen Euro den größten Auftrag in der Firmengeschichte erhalten. Das Unternehmen wird zusammen mit seinen chinesischen Partnern insgesamt 2.720 neue Wagen des chinesischen Hochgeschwindigkeitszuges CRH3 mit Brems- und Türsystemen ausrüsten.

A comparative appraisal of hydrological behavior of SRTM DEM at catchment level

NASA Astrophysics Data System (ADS)

Sharma, Arabinda; Tiwari, K. N.

2014-11-01

The Shuttle Radar Topography Mission (SRTM) data has emerged as a global elevation data in the past one decade because of its free availability, homogeneity and consistent accuracy compared to other global elevation dataset. The present study explores the consistency in hydrological behavior of the SRTM digital elevation model (DEM) with reference to easily available regional 20 m contour interpolated DEM (TOPO DEM). Analysis ranging from simple vertical accuracy assessment to hydrological simulation of the studied Maithon catchment, using empirical USLE model and semidistributed, physical SWAT model, were carried out. Moreover, terrain analysis involving hydrological indices was performed for comparative assessment of the SRTM DEM with respect to TOPO DEM. Results reveal that the vertical accuracy of SRTM DEM (±27.58 m) in the region is less than the specified standard (±16 m). Statistical analysis of hydrological indices such as topographic wetness index (TWI), stream power index (SPI), slope length factor (SLF) and geometry number (GN) shows a significant differences in hydrological properties of the two studied DEMs. Estimation of soil erosion potentials of the catchment and conservation priorities of microwatersheds of the catchment using SRTM DEM and TOPO DEM produce considerably different results. Prediction of soil erosion potential using SRTM DEM is far higher than that obtained using TOPO DEM. Similarly, conservation priorities determined using the two DEMs are found to be agreed for only 34% of microwatersheds of the catchment. ArcSWAT simulation reveals that runoff predictions are less sensitive to selection of the two DEMs as compared to sediment yield prediction. The results obtained in the present study are vital to hydrological analysis as it helps understanding the hydrological behavior of the DEM without being influenced by the model structural as well as parameter uncertainty. It also reemphasized that SRTM DEM can be a valuable dataset for

Effect of DEM mesh size on AnnAGNPS simulation and slope correction.

PubMed

Wang, Xiaoyan; Lin, Q

2011-08-01

The objective of this paper is to study the impact of the mesh size of the digital elevation model (DEM) on terrain attributes within an Annualized AGricultural NonPoint Source pollution (AnnAGNPS) Model simulation at watershed scale and provide a correction of slope gradient for low resolution DEMs. The effect of different grid sizes of DEMs on terrain attributes was examined by comparing eight DEMs (30, 40, 50, 60, 70, 80, 90, and 100 m). The accuracy of the AnnAGNPS stimulation on runoff, sediments, and nutrient loads is evaluated. The results are as follows: (1) Rnoff does not vary much with decrease of DEM resolution whereas soil erosion and total nitrogen (TN) load change prominently. There is little effect on runoff simulation of AnnAGNPS modeling by the amended slope using an adjusted 50 m DEM. (2) A decrease of sediment yield and TN load is observed with an increase of DEM mesh size from 30 to 60 m; a slight decrease of sediment and TN load with the DEM mesh size bigger than 60 m. There is similar trend for total phosphorus (TP) variation, but with less range of variation, the simulation of sediment, TN, and TP increase, in which sediment increase up to 1.75 times compared to the model using unadjusted 50 m DEM. In all, the amended simulation still has a large difference relative to the results using 30 m DEM. AnnAGNPS is less reliable for sediment loading prediction in a small hilly watershed. (3) Resolution of DEM has significant impact on slope gradient. The average, minimum, maximum of slope from the various DEMs reduced obviously with the decrease of DEM precision. For the grade of 0∼15°, the slopes at lower resolution DEM are generally bigger than those at higher resolution DEM. But for the grade bigger than 15°, the slopes at lower resolution DEM are generally smaller than those at higher resolution DEM. So it is necessary to adjust the slope with a fitting equation. A cubic model is used for correction of slope gradient from lower resolution to

In need of combined topography and bathymetry DEM

NASA Astrophysics Data System (ADS)

Kisimoto, K.; Hilde, T.

2003-04-01

. Although the coverage of this database is only a small portion of the Earth, the database has been highly appreciated in the academic community, and accepted in surprise by the general public when the database was displayed in 3D imagery to show its quality. This database could be rather smoothly combined with the finer land DEM of 250m spatial resolution (Japan250m.grd, K. Kisimoto, 2000). One of the most important applications of this combined DEM of topography and bathymetry is tsunami modeling. Understanding of the coastal environment, management and development of the coastal region are other fields in need of these data. There is, however, an important issue to consider when we create a combined DEM of topography and bathymetry in finer resolutions. The problem arises from the discrepancy of the standard datum planes or reference levels used for topographic leveling and bathymetric sounding. Land topography (altitude) is defined by leveling from the single reference point determined by average mean sea level, in other words, land height is measured from the geoid. On the other hand, depth charts are made based on depth measured from locally determined reference sea surface level, and this value of sea surface level is taken from the long term average of the lowest tidal height. So, to create a combined DEM of topography and bathymetry in very fine scale, we need to avoid this inconsistency between height and depth across the coastal region. Height and depth should be physically continuous relative to a single reference datum across the coast within such new high resolution DEMs. (N.B. Coast line is not equal to 'altitude-zero line' nor 'depth-zero line'. It is defined locally as the long term average of the highest tide level.) All of this said, we still need a lot of work on the ocean side. Global coverage with detailed bathymetric mapping is still poor. Seafloor imaging and other geophysical measurements/experiments should be organized and conducted internationally

Exploring Surfaces of Nanomaterials - MIT Spectrum

Science.gov Websites

Topics About Search for: Search Massachusetts Institute of Technology Yang Shao-Horn is tackling the inspired by them to work here." Learn More Yang Shao-Horn Topics battery Energy Materials Science Latest Stories Spectrum Issues Topics About Popular Latest MIT Campaign for a Better World MIT Campaign

Blutpräparate und therapeutische Anwendung (Hämotherapie)

NASA Astrophysics Data System (ADS)

Burkhart, Jürgen; Leimbach, Rainer; Nagl, Detlev; Weinauer, Franz

Die Geschichte der Blutübertragung lässt sich bis in das Altertum verfolgen - wenn auch hier das Blut nicht in die Blutgefäße eingebracht, sondern als Trank verabreicht wurde. Im alten Rom stürmten die Zuschauer in die Kampfarena, um das Blut verletzter Gladiatoren zu trinken, in dem Gedanken, deren Stärke würde in sie überfließen. So wurden auch Greise mit dem Blut von Jünglingen behandelt. Der Glaube, mit dem Blut würden Eigenschaften des Spenders übertragen, muss wohl auch bei dem Versuch mitgewirkt haben, Verbrecher durch Übertragung von Schafsblut "lammfromm“ zu machen. Zu Beginn der Mensch-zu-Mensch-Übertragung wurde Blut mittels eines Röhrchens von Blutgefäß zu Blutgefäß transfundiert. Diese im Mittelalter neu erprobte Form basierte auf der Entdeckung des Blutkreislaufes durch William Harvey (1578-1657). Es überwog allerdings noch die Blutübertragung vom Tier auf den Menschen, die nicht selten mit dem Tod beider Beteiligter endete. In der aufklärerischen Phase der französischen Revolution wurde diese Art der Blutübertragung deshalb verboten.

Research on a dem Coregistration Method Based on the SAR Imaging Geometry

NASA Astrophysics Data System (ADS)

Niu, Y.; Zhao, C.; Zhang, J.; Wang, L.; Li, B.; Fan, L.

2018-04-01

Due to the systematic error, especially the horizontal deviation that exists in the multi-source, multi-temporal DEMs (Digital Elevation Models), a method for high precision coregistration is needed. This paper presents a new fast DEM coregistration method based on a given SAR (Synthetic Aperture Radar) imaging geometry to overcome the divergence and time-consuming problem of the conventional DEM coregistration method. First, intensity images are simulated for two DEMs under the given SAR imaging geometry. 2D (Two-dimensional) offsets are estimated in the frequency domain using the intensity cross-correlation operation in the FFT (Fast Fourier Transform) tool, which can greatly accelerate the calculation process. Next, the transformation function between two DEMs is achieved via the robust least-square fitting of 2D polynomial operation. Accordingly, two DEMs can be precisely coregistered. Last, two DEMs, i.e., one high-resolution LiDAR (Light Detection and Ranging) DEM and one low-resolution SRTM (Shutter Radar Topography Mission) DEM, covering the Yangjiao landslide region of Chongqing are taken as an example to test the new method. The results indicate that, in most cases, this new method can achieve not only a result as much as 80 times faster than the minimum elevation difference (Least Z-difference, LZD) DEM registration method, but also more accurate and more reliable results.

DEMS - a second generation diabetes electronic management system.

PubMed

Gorman, C A; Zimmerman, B R; Smith, S A; Dinneen, S F; Knudsen, J B; Holm, D; Jorgensen, B; Bjornsen, S; Planet, K; Hanson, P; Rizza, R A

2000-06-01

Diabetes electronic management system (DEMS) is a component-based client/server application, written in Visual C++ and Visual Basic, with the database server running Sybase System 11. DEMS is built entirely with a combination of dynamic link libraries (DLLs) and ActiveX components - the only exception is the DEMS.exe. DEMS is a chronic disease management system for patients with diabetes. It is used at the point of care by all members of the diabetes team including physicians, nurses, dieticians, clinical assistants and educators. The system is designed for maximum clinical efficiency and facilitates appropriately supervised delegation of care. Dispersed clinical sites may be supervised from a central location. The system is designed for ease of navigation; immediate provision of many types of automatically generated reports; quality audits; aids to compliance with good care guidelines; and alerts, advisories, prompts, and warnings that guide the care provider. The system now contains data on over 34000 patients and is in daily use at multiple sites.

A New DEM Generalization Method Based on Watershed and Tree Structure

PubMed Central

Chen, Yonggang; Ma, Tianwu; Chen, Xiaoyin; Chen, Zhende; Yang, Chunju; Lin, Chenzhi; Shan, Ligang

2016-01-01

The DEM generalization is the basis of multi-dimensional observation, the basis of expressing and analyzing the terrain. DEM is also the core of building the Multi-Scale Geographic Database. Thus, many researchers have studied both the theory and the method of DEM generalization. This paper proposed a new method of generalizing terrain, which extracts feature points based on the tree model construction which considering the nested relationship of watershed characteristics. The paper used the 5 m resolution DEM of the Jiuyuan gully watersheds in the Loess Plateau as the original data and extracted the feature points in every single watershed to reconstruct the DEM. The paper has achieved generalization from 1:10000 DEM to 1:50000 DEM by computing the best threshold. The best threshold is 0.06. In the last part of the paper, the height accuracy of the generalized DEM is analyzed by comparing it with some other classic methods, such as aggregation, resample, and VIP based on the original 1:50000 DEM. The outcome shows that the method performed well. The method can choose the best threshold according to the target generalization scale to decide the density of the feature points in the watershed. Meanwhile, this method can reserve the skeleton of the terrain, which can meet the needs of different levels of generalization. Additionally, through overlapped contour contrast, elevation statistical parameters and slope and aspect analysis, we found out that the W8D algorithm performed well and effectively in terrain representation. PMID:27517296

Shape and Albedo from Shading (SAfS) for Pixel-Level dem Generation from Monocular Images Constrained by Low-Resolution dem

NASA Astrophysics Data System (ADS)

Wu, Bo; Chung Liu, Wai; Grumpe, Arne; Wöhler, Christian

2016-06-01

Lunar topographic information, e.g., lunar DEM (Digital Elevation Model), is very important for lunar exploration missions and scientific research. Lunar DEMs are typically generated from photogrammetric image processing or laser altimetry, of which photogrammetric methods require multiple stereo images of an area. DEMs generated from these methods are usually achieved by various interpolation techniques, leading to interpolation artifacts in the resulting DEM. On the other hand, photometric shape reconstruction, e.g., SfS (Shape from Shading), extensively studied in the field of Computer Vision has been introduced to pixel-level resolution DEM refinement. SfS methods have the ability to reconstruct pixel-wise terrain details that explain a given image of the terrain. If the terrain and its corresponding pixel-wise albedo were to be estimated simultaneously, this is a SAfS (Shape and Albedo from Shading) problem and it will be under-determined without additional information. Previous works show strong statistical regularities in albedo of natural objects, and this is even more logically valid in the case of lunar surface due to its lower surface albedo complexity than the Earth. In this paper we suggest a method that refines a lower-resolution DEM to pixel-level resolution given a monocular image of the coverage with known light source, at the same time we also estimate the corresponding pixel-wise albedo map. We regulate the behaviour of albedo and shape such that the optimized terrain and albedo are the likely solutions that explain the corresponding image. The parameters in the approach are optimized through a kernel-based relaxation framework to gain computational advantages. In this research we experimentally employ the Lunar-Lambertian model for reflectance modelling; the framework of the algorithm is expected to be independent of a specific reflectance model. Experiments are carried out using the monocular images from Lunar Reconnaissance Orbiter (LRO

On the COSMO-SkyMed Exploitation for Interferometric DEM Generation

NASA Astrophysics Data System (ADS)

Teresa, C. M.; Raffaele, N.; Oscar, N. D.; Fabio, B.

2011-12-01

DEM products for Earth observation space-borne applications are being to play a role of increasing importance due to the new generation of high resolution sensors (both optical and SAR). These new sensors demand elevation data for processing and, on the other hand, they provide new possibilities for DEM generation. Till now, for what concerns interferometric DEM, the Shuttle Radar Topography Mission (SRTM) has been the reference product for scientific applications all over the world. SRTM mission [1] had the challenging goal to meet the requirements for a homogeneous and reliable DEM fulfilling the DTED-2 specifications. However, new generation of high resolution sensors (including SAR) pose new requirements for elevation data in terms of vertical precision and spatial resolution. DEM are usually used as ancillary input in different processing steps as for instance geocoding and Differential SAR Interferometry. In this context, the recent SAR missions of DLR (TerraSAR-X and TanDEM-X) and ASI (COSMO-SkyMed) can play a promising role thanks to their high resolution both in space and time. In particular, the present work investigates the potentialities of the COSMO/SkyMed (CSK) constellation for ground elevation measurement with particular attention devoted to the impact of the improved spatial resolution wrt the previous SAR sensors. The recent scientific works, [2] and [3], have shown the advantages of using CSK in the monitoring of terrain deformations caused by landslides, earthquakes, etc. On the other hand, thanks to the high spatial resolution, CSK appears to be very promising in monitoring man-made structures, such as buildings, bridges, railways and highways, thus enabling new potential applications (urban applications, precise DEM, etc.). We present results obtained by processing both SPOTLIGHT and STRIPMAP acquisitions through standard SAR Interferometry as well as multi-pass interferometry [4] with the aim of measuring ground elevation. Acknowledgments

Towards the Optimal Pixel Size of dem for Automatic Mapping of Landslide Areas

NASA Astrophysics Data System (ADS)

Pawłuszek, K.; Borkowski, A.; Tarolli, P.

2017-05-01

Determining appropriate spatial resolution of digital elevation model (DEM) is a key step for effective landslide analysis based on remote sensing data. Several studies demonstrated that choosing the finest DEM resolution is not always the best solution. Various DEM resolutions can be applicable for diverse landslide applications. Thus, this study aims to assess the influence of special resolution on automatic landslide mapping. Pixel-based approach using parametric and non-parametric classification methods, namely feed forward neural network (FFNN) and maximum likelihood classification (ML), were applied in this study. Additionally, this allowed to determine the impact of used classification method for selection of DEM resolution. Landslide affected areas were mapped based on four DEMs generated at 1 m, 2 m, 5 m and 10 m spatial resolution from airborne laser scanning (ALS) data. The performance of the landslide mapping was then evaluated by applying landslide inventory map and computation of confusion matrix. The results of this study suggests that the finest scale of DEM is not always the best fit, however working at 1 m DEM resolution on micro-topography scale, can show different results. The best performance was found at 5 m DEM-resolution for FFNN and 1 m DEM resolution for results. The best performance was found to be using 5 m DEM-resolution for FFNN and 1 m DEM resolution for ML classification.

Kompressionstherapie bei Patienten mit Ulcus cruris venosum.

PubMed

Dissemond, Joachim; Assenheimer, Bernd; Bültemann, Anke; Gerber, Veronika; Gretener, Silvia; Kohler-von Siebenthal, Elisabeth; Koller, Sonja; Kröger, Knut; Kurz, Peter; Läuchli, Severin; Münter, Christian; Panfil, Eva-Maria; Probst, Sebastian; Protz, Kerstin; Riepe, Gunnar; Strohal, Robert; Traber, Jürg; Partsch, Hugo

2016-11-01

Wund-D.A.CH. ist der Dachverband deutschsprachiger Fachgesellschaften, die sich mit den Thematiken der Wundbehandlung beschäftigen. Experten verschiedener Fachgesellschaften aus Deutschland, Österreich und der Schweiz haben nun einen aktuellen Konsens der Kompressionstherapie für Patienten mit Ulcus cruris venosum erstellt. In Europa ist das Ulcus cruris venosum eine der häufigsten Ursachen für chronische Wunden. Neben der konservativen und interventionellen Wund- und Venentherapie, ist die Kompressionstherapie die Basis der Behandlungsstrategien. Die Kompressionstherapie kann heute mit sehr unterschiedlichen Materialien und Systemen durchgeführt werden. Während in der Entstauungsphase insbesondere Verbände mit Kurzzugbinden oder Mehrkomponentensysteme zur Anwendung kommen, sind es anschließend überwiegend Ulkus-Strumpfsysteme. Eine weitere, bislang wenig verbreitete Alternative sind adaptive Kompressionsbandagen. Insbesondere für die Rezidivprophylaxe werden medizinische Kompressionsstrümpfe empfohlen. Durch die Vielzahl der heute zur Verfügung stehenden Behandlungsoptionen, kann für nahezu alle Patienten ein Konzept entwickelt werden, dass sich an den individuellen Bedürfnissen und Fähigkeiten orientiert und daher auch akzeptiert und durchgeführt wird. Die Kompressionstherapie ist für die Behandlung von Patienten mit Ulcus cruris venosum essentiell. In den letzten Jahren sind viele verschiedene Therapieoptionen verfügbar, die in den deutschsprachigen Ländern unterschiedlich angewendet oder durchgeführt werden. Daher soll dieser Expertenkonsens dazu beitragen, konkrete Empfehlungen für die praktische Durchführung der Kompressionstherapie von Patienten mit Ulcus cruris venosum darzustellen. © 2016 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

MPD work at MIT

NASA Technical Reports Server (NTRS)

Martinez-Sanchez, Manuel

1991-01-01

MPD work at MIT is presented in the form of the view-graphs. The following subject areas are covered: the MIT program, its goals, achievements, and roadblocks; quasi one-dimensional modeling; two-dimensional modeling - transport effects and Hall effect; microscopic instabilities in MPD flows and modified two stream instability; electrothermal stability theory; separation of onset and anode depletion; exit plane spectroscopic measurements; phenomena of onset as performance limiter; explanations of onset; geometry effects on onset; onset at full ionization and its consequences; relationship to anode depletion; summary on self-field MPD; applied field MPD - the logical growth path; the case for AF; the challenges of AF MPD; and recommendations.

a Method of Generating dem from Dsm Based on Airborne Insar Data

NASA Astrophysics Data System (ADS)

Lu, W.; Zhang, J.; Xue, G.; Wang, C.

2018-04-01

Traditional methods of terrestrial survey to acquire DEM cannot meet the requirement of acquiring large quantities of data in real time, but the DSM can be quickly obtained by using the dual antenna synthetic aperture radar interferometry and the DEM generated by the DSM is more fast and accurate. Therefore it is most important to acquire DEM from DSM based on airborne InSAR data. This paper aims to the method that generate DEM from DSM accurately. Two steps in this paper are applied to acquire accurate DEM. First of all, when the DSM is generated by interferometry, unavoidable factors such as overlay and shadow will produce gross errors to affect the data accuracy, so the adaptive threshold segmentation method is adopted to remove the gross errors and the threshold is selected according to the coherence of the interferometry. Secondly DEM will be generated by the progressive triangulated irregular network densification filtering algorithm. Finally, experimental results are compared with the existing high-precision DEM results. The results show that this method can effectively filter out buildings, vegetation and other objects to obtain the high-precision DEM.

Wrestling with Pedagogical Change: The TEAL Initiative at MIT

ERIC Educational Resources Information Center

Breslow, Lori

2010-01-01

In the late 1990s, the physics department at the Massachusetts Institute of Technology (MIT) had a problem. The department was responsible for teaching the two required physics courses that are part of the General Institute Requirements (GIRs), MIT's core curriculum--Physics I (mechanics, or in MIT parlance, 8.01) and Physics II (electricity and…

Topographic representation using DEMs and its applications to active tectonics research

NASA Astrophysics Data System (ADS)

Oguchi, T.; Lin, Z.; Hayakawa, Y. S.

2016-12-01

Identifying topographic deformations due to active tectonics has been a principal issue in tectonic geomorphology. It provides useful information such as whether a fault has been active during the recent past. Traditionally, field observations, conventional surveying, and visual interpretation of topographic maps, aerial photos, and satellite images were the main methods for such geomorphological investigations. However, recent studies have been utilizing digital elevation models (DEMs) to visualize and quantitatively analyze landforms. There are many advantages to the use of DEMs for research in active tectonics. For example, unlike aerial photos and satellite images, DEMs show ground conditions without vegetation and man-made objects such as buildings, permitting direct representation of tectonically deformed landforms. Recent developments and advances in airborne LiDAR also allow the fast creation of DEMs even in vegetated areas such as forested lands. In addition, DEMs enable flexible topographic visualization based on various digital cartographic and computer-graphic techniques, facilitating identification of particular landforms such as active faults. Further, recent progress in morphometric analyses using DEMs can be employed to quantitatively represent topographic characteristics, and objectively evaluate tectonic deformation and the properties of related landforms. This paper presents a review of DEM applications in tectonic geomorphology, with attention to historical development, recent advances, and future perspectives. Examples are taken mainly from Japan, a typical tectonically active country. The broader contributions of DEM-based active tectonics research to other fields, such as fluvial geomorphology and geochronology, will also be discussed.

Which DEM is best for analyzing fluvial landscape development in mountainous terrains?

NASA Astrophysics Data System (ADS)

Boulton, Sarah J.; Stokes, Martin

2018-06-01

Regional studies of fluvial landforms and long-term (Quaternary) landscape development in remote mountain landscapes routinely use satellite-derived DEM data sets. The SRTM and ASTER DEMs are the most commonly utilised because of their longer availability, free cost, and ease of access. However, rapid technological developments mean that newer and higher resolution DEM data sets such as ALOS World 3D (AW3D) and TanDEM-X are being released to the scientific community. Geomorphologists are thus faced with an increasingly problematic challenge of selecting an appropriate DEM for their landscape analyses. Here, we test the application of four medium resolution DEM products (30 m = SRTM, ASTER, AW3D; 12 m = TanDEM-X) for qualitative and quantitative analysis of a fluvial mountain landscape using the Dades River catchment (High Atlas Mountains, Morocco). This landscape comprises significant DEM remote sensing challenges, notably a high mountain relief, steep slopes, and a deeply incised high sinuosity drainage network with narrow canyon/gorge reaches. Our goal was to see which DEM produced the most representative best fit drainage network and meaningful quantification. To achieve this, we used ArcGIS and Stream Profiler platforms to generate catchment hillshade and slope rasters and to extract drainage network, channel long profile and channel slope, and area data. TanDEM-X produces the clearest landscape representation but with channel routing errors in localised high relief areas. Thirty-metre DEMs are smoother and less detailed, but the AW3D shows the closest fit to the real drainage network configuration. The TanDEM-X elevation values are the closest to field-derived GPS measurements. Long profiles exhibit similar shapes but with minor differences in length, elevation, and the degree of noise/smoothing, with AW3D producing the best representation. Slope-area plots display similarly positioned slope-break knickpoints with modest differences in steepness and concavity

Evaluation of lidar-derived DEMs through terrain analysis and field comparison

Treesearch

Cody P. Gillin; Scott W. Bailey; Kevin J. McGuire; Stephen P. Prisley

2015-01-01

Topographic analysis of watershed-scale soil and hydrological processes using digital elevation models (DEMs) is commonplace, but most studies have used DEMs of 10 m resolution or coarser. Availability of higher-resolution DEMs created from light detection and ranging (lidar) data is increasing but their suitability for such applications has received little critical...

[Cardiodoron® bei Patienten mit Schlafstörungen - Ergebnisse einer prospektiven Beobachtungsstudie].

PubMed

Rother, Claudia; Schnelle, Martin

Hintergrund: Schlafstörungen gehören zu den häufigsten gesundheitlichen Problemen der heutigen Zeit. Stress und die dadurch bedingte innere Anspannung sowie eine unrhythmische Lebensführung z.B. durch Schichtarbeit sind bekannte auslösende Faktoren. Weniger bekannt ist, dass auch funktionelle Herz-Kreislauf-Beschwerden zu Störungen des Schlafs führen können und dass deren Behandlung zu einer Verbesserung der Schlafqualität beiträgt. Ganzheitlich betrachtet geht es daher um die Wiederherstellung einer gesunden Rhythmik, insbesondere des Herz-/Atem- sowie des Schlaf-Wach-Rhythmus, die Cardiodoron®, eine Heilpflanzenkomposition aus Primula veris, Hyoscyamus niger und Onopordum acanthium, unterstützt. Patienten und Methoden: Mittels einer prospektiven, multizentrischen Beobachtungsstudie sollte ermittelt werden, wie sich funktionelle Herz-Kreislauf-Beschwerden und/oder Schlafstörungen unter der Behandlung mit Cardiodoron® (Dilution) über 3-6 Monate entwickeln. Im Zeitraum von September 2009 bis März 2012 dokumentierten 92 Ärzte 501 Patienten, von denen 380 über Schlafstörungen klagten und deren Daten in dieser Publikation näher betrachtet werden. Nach einer Aufnahmeuntersuchung erfolgte nach 90 Tagen eine Abschlussuntersuchung und bei Fortführung der Therapie nach nochmals 90 Tagen eine Follow-up-Untersuchung. Neben 30 ärztlicherseits bewerteten Symptomen beurteilten die Patienten ihr Befinden mittels Pittsburgh Sleep Quality Index (PSQI) nach Buysse und der Beschwerden-Liste nach von Zerssen (B-L und B-L'). Ergebnisse: Unter der Cardiodoron®-Therapie gingen bei guter Verträglichkeit sowohl die Ausprägung der Schlafstörungen (um 65% von 2,0 auf 0,7 Punkte) als auch die erfassten 30 Symptome (um 59% von 24,3 auf 9,9 Punkte) deutlich zurück (p < 0,01). Weiterhin reduzierten sich der PSQI und der Gesamtwert der Beschwerden-Liste signifikant (p < 0,0001) um 60% bzw. 56% (von 12,2 auf 4,8 bzw. von 25,6 auf 11,4 Punkte). Schlussfolgerungen: Bei

A Comparative Study of Radar Stereo and Interferometry for DEM Generation

NASA Astrophysics Data System (ADS)

Gelautz, M.; Paillou, P.; Chen, C. W.; Zebker, H. A.

2004-06-01

In this experiment, we derive and compare radar stereo and interferometric elevation models (DEMs) of a study site in Djibouti, East Africa. As test data, we use a Radarsat stereo pair and ERS-2 and Radarsat interferometric data. Comparison of the reconstructed DEMs with a SPOT reference DEM shows that in regions of high coherence the DEMs produced by interferometry are of much better quality than the stereo result. However, the interferometric error histograms also show some pronounced outliers due to decorrelation and phase unwrapping problems on forested mountain slopes. The more robust stereo result is able to capture the general terrain shape, but finer surface details are lost. A fusion experiment demonstrates that merging the stereoscopic and interferometric DEMs by utilizing coherence- derived weights can significantly improve the accuracy of the computed elevation maps.

Cross Validation on the Equality of Uav-Based and Contour-Based Dems

NASA Astrophysics Data System (ADS)

Ma, R.; Xu, Z.; Wu, L.; Liu, S.

2018-04-01

Unmanned Aerial Vehicles (UAV) have been widely used for Digital Elevation Model (DEM) generation in geographic applications. This paper proposes a novel framework of generating DEM from UAV images. It starts with the generation of the point clouds by image matching, where the flight control data are used as reference for searching for the corresponding images, leading to a significant time saving. Besides, a set of ground control points (GCP) obtained from field surveying are used to transform the point clouds to the user's coordinate system. Following that, we use a multi-feature based supervised classification method for discriminating non-ground points from ground ones. In the end, we generate DEM by constructing triangular irregular networks and rasterization. The experiments are conducted in the east of Jilin province in China, which has been suffered from soil erosion for several years. The quality of UAV based DEM (UAV-DEM) is compared with that generated from contour interpolation (Contour-DEM). The comparison shows a higher resolution, as well as higher accuracy of UAV-DEMs, which contains more geographic information. In addition, the RMSE errors of the UAV-DEMs generated from point clouds with and without GCPs are ±0.5 m and ±20 m, respectively.

DEM generation in cloudy-rainy mountainous area with multi-baseline SAR interferometry

NASA Astrophysics Data System (ADS)

Wu, Hong'an; Zhang, Yonghong; Jiang, Decai; Kang, Yonghui

2018-03-01

Conventional singe baseline InSAR is easily affected by atmospheric artifacts, making it difficult to generate highprecision DEM. To solve this problem, in this paper, a multi-baseline interferometric phase accumulation method with weights fixed by coherence is proposed to generate higher accuracy DEM. The mountainous area in Kunming, Yunnan Province, China is selected as study area, which is characterized by cloudy weather, rugged terrain and dense vegetation. The multi-baseline InSAR experiments are carried out by use of four ALOS-2 PALSAR-2 images. The generated DEM is evaluated by Chinese Digital Products of Fundamental Geographic Information 1:50000 DEM. The results demonstrate that: 1) the proposed method can reduce atmospheric artifacts significantly; 2) the accuracy of InSAR DEM generated by six interferograms satisfies the standard of 1:50000 DEM Level Three and American DTED-1.

Minimally invasive thyroidectomy (MIT): indications and results.

PubMed

Docimo, Giovanni; Salvatore Tolone, Salvatore; Gili, Simona; d'Alessandro, A; Casalino, G; Brusciano, L; Ruggiero, Roberto; Docimo, Ludovico

2013-01-01

To establish if the indication for different approaches for thyroidectomy and the incision length provided by means of pre-operative assessment of gland volume and size of nodules resulted in safe and effective outcomes and in any notable aesthetic or quality-of-life impact on patients. Ninehundred eightytwo consecutive patients, undergoing total thyroidectomy, were enrolled. The thyroid volume and maximal nodule diameter were measured by means of ultrasounds. Based on ultrasounds findings, patients were divided into three groups: minimally invasive video assisted thyroidectomy (MIVAT), minimally invasive thyroidectomy (MIT) and conventional thyroidectomy (CT) groups. The data concerning the following parameters were collected: operative time, postoperative complications, postoperative pain and cosmetic results. The MIVAT group included 179 patients, MIT group included 592 patients and CT group included 211 patients. Incidence of complications did not differ significantly in each group. In MIVAT and MIT group, the perception of postoperative pain was less intense than CT group. The patients in the MIVAT (7±1.5) and MIT (8±2) groups were more satisfied with the cosmetic results than those in CT group (5±1.3) (p= <0.05). The MIT is a technique totally reproducible, and easily convertible to perform surgical procedures in respect of the patient, without additional complications, increased costs, and with better aesthetic results.

Generating DEM from LIDAR data - comparison of available software tools

NASA Astrophysics Data System (ADS)

Korzeniowska, K.; Lacka, M.

2011-12-01

In recent years many software tools and applications have appeared that offer procedures, scripts and algorithms to process and visualize ALS data. This variety of software tools and of "point cloud" processing methods contributed to the aim of this study: to assess algorithms available in various software tools that are used to classify LIDAR "point cloud" data, through a careful examination of Digital Elevation Models (DEMs) generated from LIDAR data on a base of these algorithms. The works focused on the most important available software tools: both commercial and open source ones. Two sites in a mountain area were selected for the study. The area of each site is 0.645 sq km. DEMs generated with analysed software tools ware compared with a reference dataset, generated using manual methods to eliminate non ground points. Surfaces were analysed using raster analysis. Minimum, maximum and mean differences between reference DEM and DEMs generated with analysed software tools were calculated, together with Root Mean Square Error. Differences between DEMs were also examined visually using transects along the grid axes in the test sites.

MIT-Skywalker: On the use of a markerless system.

PubMed

Goncalves, Rogerio S; Hamilton, Taya; Krebs, Hermano I

2017-07-01

This paper describes our efforts to employ the Microsoft Kinect as a low cost vision control system for the MIT-Skywalker, a robotic gait rehabilitation device. The Kinect enables an alternative markerless solution to control the MIT-Skywalker and allows a more user-friendly set-up. A study involving eight healthy subjects and two stroke survivors using the MIT-Skywalker device demonstrates the advantages and challenges of this new proposed approach.

MIT Space Engineering Research Center

NASA Technical Reports Server (NTRS)

Crawley, Edward F.; Miller, David W.

1990-01-01

The Space Engineering Research Center (SERC) at MIT, started in Jul. 1988, has completed two years of research. The Center is approaching the operational phase of its first testbed, is midway through the construction of a second testbed, and is in the design phase of a third. We presently have seven participating faculty, four participating staff members, ten graduate students, and numerous undergraduates. This report reviews the testbed programs, individual graduate research, other SERC activities not funded by the Center, interaction with non-MIT organizations, and SERC milestones. Published papers made possible by SERC funding are included at the end of the report.

Glacier Volume Change Estimation Using Time Series of Improved Aster Dems

NASA Astrophysics Data System (ADS)

Girod, Luc; Nuth, Christopher; Kääb, Andreas

2016-06-01

Volume change data is critical to the understanding of glacier response to climate change. The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) system embarked on the Terra (EOS AM-1) satellite has been a unique source of systematic stereoscopic images covering the whole globe at 15m resolution and at a consistent quality for over 15 years. While satellite stereo sensors with significantly improved radiometric and spatial resolution are available to date, the potential of ASTER data lies in its long consistent time series that is unrivaled, though not fully exploited for change analysis due to lack of data accuracy and precision. Here, we developed an improved method for ASTER DEM generation and implemented it in the open source photogrammetric library and software suite MicMac. The method relies on the computation of a rational polynomial coefficients (RPC) model and the detection and correction of cross-track sensor jitter in order to compute DEMs. ASTER data are strongly affected by attitude jitter, mainly of approximately 4 km and 30 km wavelength, and improving the generation of ASTER DEMs requires removal of this effect. Our sensor modeling does not require ground control points and allows thus potentially for the automatic processing of large data volumes. As a proof of concept, we chose a set of glaciers with reference DEMs available to assess the quality of our measurements. We use time series of ASTER scenes from which we extracted DEMs with a ground sampling distance of 15m. Our method directly measures and accounts for the cross-track component of jitter so that the resulting DEMs are not contaminated by this process. Since the along-track component of jitter has the same direction as the stereo parallaxes, the two cannot be separated and the elevations extracted are thus contaminated by along-track jitter. Initial tests reveal no clear relation between the cross-track and along-track components so that the latter seems not to be

Novel application of DEM to modelling comminution processes

NASA Astrophysics Data System (ADS)

Delaney, Gary W.; Cleary, Paul W.; Sinnott, Matt D.; Morrison, Rob D.

2010-06-01

Comminution processes in which grains are broken down into smaller and smaller sizes represent a critical component in many industries including mineral processing, cement production, food processing and pharmaceuticals. We present a novel DEM implementation capable of realistically modelling such comminution processes. This extends on a previous implementation of DEM particle breakage that utilized spherical particles. Our new extension uses super-quadric particles, where daughter fragments with realistic size and shape distributions are packed inside a bounding parent super-quadric. We demonstrate the flexibility of our approach in different particle breakage scenarios and examine the effect of the chosen minimum resolved particle size. This incorporation of the effect of particle shape in the breakage process allows for more realistic DEM simulations to be performed, that can provide additional fundamental insights into comminution processes and into the behaviour of individual pieces of industrial machinery.

Generation and performance assessment of the global TanDEM-X digital elevation model

NASA Astrophysics Data System (ADS)

Rizzoli, Paola; Martone, Michele; Gonzalez, Carolina; Wecklich, Christopher; Borla Tridon, Daniela; Bräutigam, Benjamin; Bachmann, Markus; Schulze, Daniel; Fritz, Thomas; Huber, Martin; Wessel, Birgit; Krieger, Gerhard; Zink, Manfred; Moreira, Alberto

2017-10-01

The primary objective of the TanDEM-X mission is the generation of a global, consistent, and high-resolution digital elevation model (DEM) with unprecedented global accuracy. The goal is achieved by exploiting the interferometric capabilities of the two twin SAR satellites TerraSAR-X and TanDEM-X, which fly in a close orbit formation, acting as an X-band single-pass interferometer. Between December 2010 and early 2015 all land surfaces have been acquired at least twice, difficult terrain up to seven or eight times. The acquisition strategy, data processing, and DEM calibration and mosaicking have been systematically monitored and optimized throughout the entire mission duration, in order to fulfill the specification. The processing of all data has finally been completed in September 2016 and this paper reports on the final performance of the TanDEM-X global DEM and presents the acquisition and processing strategy which allowed to obtain the final DEM quality. The results confirm the outstanding global accuracy of the delivered product, which can be now utilized for both scientific and commercial applications.

The development of form two mathematics i-Think module (Mi-T2)

NASA Astrophysics Data System (ADS)

Yao, Foo Jing; Abdullah, Mohd Faizal Nizam Lee; Tien, Lee Tien

2017-05-01

This study aims to develop a training module i-THINK Mathematics Form Two (Mi-T2) to increase the higher-order thinking skills of students. The Mi-T2 training module was built based on the Sidek Module Development Model (2001). Constructivist learning theory, cognitive learning theory, i-THINK map and higher order thinking skills were the building blocks of the module development. In this study, researcher determined the validity and reliability of Mi-T2 module. The design being used in this study was descriptive study. To determine the needs of Mi-T2 module, questionnaires and literature review were used to collect data. When the need of the module was determined, the module was built and a pilot study was conducted to test the reliability of the Mi-T2 module. The pilot study was conducted at a secondary school in North Kinta, Perak. A Form Two class was selected to be the sample study through clustered random sampling. The pilot study was conducted for two months and one topic had been studied. The Mi-T2 module was evaluated by five expert panels to determine the content validity of the module. The instruments being used in the study were questionnaires about the necessity of the Mi-T2 module for guidance, questionnaires about the validity of the module and questionnaires concerning the reliability of the module. Statistical analysis was conducted to determine the validity and reliability coefficients of the Mi-T2 module. The content validity of Mi-T2 module was determined by Cohen's Kappa's (1968) agreement coefficient and the reliability of Mi-T2 module was determined by Cronbach Alpha's value scale. The content validity of Mi-T2 module was 0.89 and the Cronbach Alpha's value of Mi-T2 module was 0.911.

Spaceborne radar interferometry for coastal DEM construction

USGS Publications Warehouse

Hong, S.-H.; Lee, C.-W.; Won, J.-S.; Kwoun, Oh-Ig; Lu, Z.

2005-01-01

Topographic features in coastal regions including tidal flats change more significantly than landmass, and are characterized by extremely low slopes. High precision DEMs are required to monitor dynamic changes in coastal topography. It is difficult to obtain coherent interferometric SAR pairs especially over tidal flats mainly because of variation of tidal conditions. Here we focus on i) coherence of multi-pass ERS SAR interferometric pairs and ii) DEM construction from ERS-ENVISAT pairs. Coherences of multi-pass ERS interferograms were good enough to construct DEM under favorable tidal conditions. Coherence in sand dominant area was generally higher than that in muddy surface. The coarse grained coastal areas are favorable for multi-pass interferometry. Utilization of ERS-ENVISAT interferometric pairs is taken a growing interest. We carried out investigation using a cross-interferometric pair with a normal baseline of about 1.3 km, a 30 minutes temporal separation and the height sensitivity of about 6 meters. Preliminary results of ERS-ENVISAT interferometry were not successful due to baseline and unfavorable scattering conditions. ?? 2005 IEEE.

ArcticDEM Year 3; Improving Coverage, Repetition and Resolution

NASA Astrophysics Data System (ADS)

Morin, P. J.; Porter, C. C.; Cloutier, M.; Howat, I.; Noh, M. J.; Willis, M. J.; Candela, S. G.; Bauer, G.; Kramer, W.; Bates, B.; Williamson, C.

2017-12-01

Surface topography is among the most fundamental data sets for geosciences, essential for disciplines ranging from glaciology to geodynamics. The ArcticDEM project is using sub-meter, commercial imagery licensed by the National Geospatial-Intelligence Agency, petascale computing, and open source photogrammetry software to produce a time-tagged 2m posting elevation model and a 5m posting mosaic of the entire Arctic region. As ArcticDEM enters its third year, the region has gone from having some of the sparsest and poorest elevation data to some of the most precise and complete data of any region on the globe. To date, we have produced and released over 80,000,000 km2 as 57,000 - 2m posting, time-stamped DEMs. The Arctic, on average, is covered four times though there are hotspots with more than 100 DEMs. In addition, the version 1 release includes a 5m posting mosaic covering the entire 20,000,000 km2 region. All products are publically available through arctidem.org, ESRI web services, and a web viewer. The final year of the project will consist of a complete refiltering of clouds/water and re-mosaicing of all elevation data. Since inception of the project, post-processing techniques have improved significantly, resulting in fewer voids, better registration, sharper coastlines, and fewer inaccuracies due to clouds. All ArcticDEM data will be released in 2018. Data, documentation, web services and web viewer are available at arcticdem.org

Scenario-Based Validation of Moderate Resolution DEMs Freely Available for Complex Himalayan Terrain

NASA Astrophysics Data System (ADS)

Singh, Mritunjay Kumar; Gupta, R. D.; Snehmani; Bhardwaj, Anshuman; Ganju, Ashwagosha

2016-02-01

Accuracy of the Digital Elevation Model (DEM) affects the accuracy of various geoscience and environmental modelling results. This study evaluates accuracies of the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) Global DEM Version-2 (GDEM V2), the Shuttle Radar Topography Mission (SRTM) X-band DEM and the NRSC Cartosat-1 DEM V1 (CartoDEM). A high resolution (1 m) photogrammetric DEM (ADS80 DEM), having a high absolute accuracy [1.60 m linear error at 90 % confidence (LE90)], resampled at 30 m cell size was used as reference. The overall root mean square error (RMSE) in vertical accuracy was 23, 73, and 166 m and the LE90 was 36, 75, and 256 m for ASTER GDEM V2, SRTM X-band DEM and CartoDEM, respectively. A detailed error analysis was performed for individual as well as combinations of different classes of aspect, slope, land-cover and elevation zones for the study area. For the ASTER GDEM V2, forest areas with North facing slopes (0°-5°) in the 4th elevation zone (3773-4369 m) showed minimum LE90 of 0.99 m, and barren with East facing slopes (>60°) falling under the 2nd elevation zone (2581-3177 m) showed maximum LE90 of 166 m. For the SRTM DEM, pixels with South-East facing slopes of 0°-5° in the 4th elevation zone covered with forest showed least LE90 of 0.33 m and maximum LE90 of 521 m was observed in the barren area with North-East facing slope (>60°) in the 4th elevation zone. In case of the CartoDEM, the snow pixels in the 2nd elevation zone with South-East facing slopes of 5°-15° showed least LE90 of 0.71 m and maximum LE90 of 1266 m was observed for the snow pixels in the 3rd elevation zone (3177-3773 m) within the South facing slope of 45°-60°. These results can be highly useful for the researchers using DEM products in various modelling exercises.

Physik gestern und heute: Visualisierung mit der Schlierenmethode

NASA Astrophysics Data System (ADS)

Heering, Peter

2006-07-01

Der Name des österreichischen Forschers Ernst Mach ist heute noch mit der Schallgeschwindigkeit verbunden. Diese Auszeichnung resultiert aus Machs Untersuchungen, wie sich Projektile mit Überschallgeschwindigkeit durch die Luft bewegen. Gerade in jüngster Zeit hat die Anwendung derartiger Methoden durch technische Modifikationen wieder einen Aufschwung erfahren.

Open-Source Digital Elevation Model (DEMs) Evaluation with GPS and LiDAR Data

NASA Astrophysics Data System (ADS)

Khalid, N. F.; Din, A. H. M.; Omar, K. M.; Khanan, M. F. A.; Omar, A. H.; Hamid, A. I. A.; Pa'suya, M. F.

2016-09-01

Advanced Spaceborne Thermal Emission and Reflection Radiometer-Global Digital Elevation Model (ASTER GDEM), Shuttle Radar Topography Mission (SRTM), and Global Multi-resolution Terrain Elevation Data 2010 (GMTED2010) are freely available Digital Elevation Model (DEM) datasets for environmental modeling and studies. The quality of spatial resolution and vertical accuracy of the DEM data source has a great influence particularly on the accuracy specifically for inundation mapping. Most of the coastal inundation risk studies used the publicly available DEM to estimated the coastal inundation and associated damaged especially to human population based on the increment of sea level. In this study, the comparison between ground truth data from Global Positioning System (GPS) observation and DEM is done to evaluate the accuracy of each DEM. The vertical accuracy of SRTM shows better result against ASTER and GMTED10 with an RMSE of 6.054 m. On top of the accuracy, the correlation of DEM is identified with the high determination of coefficient of 0.912 for SRTM. For coastal zone area, DEMs based on airborne light detection and ranging (LiDAR) dataset was used as ground truth data relating to terrain height. In this case, the LiDAR DEM is compared against the new SRTM DEM after applying the scale factor. From the findings, the accuracy of the new DEM model from SRTM can be improved by applying scale factor. The result clearly shows that the value of RMSE exhibit slightly different when it reached 0.503 m. Hence, this new model is the most suitable and meets the accuracy requirement for coastal inundation risk assessment using open source data. The suitability of these datasets for further analysis on coastal management studies is vital to assess the potentially vulnerable areas caused by coastal inundation.

MIT-CSR XIS Project

NASA Technical Reports Server (NTRS)

1998-01-01

This report outlines the proposers' progress toward MIT's contribution to the X-Ray Imaging Spectrometer (XIS) experiment on the Japanese ASTRO-E mission. The report discusses electrical system design, mechanical system design, and ground support equipment.

How does modifying a DEM to reflect known hydrology affect subsequent terrain analysis?

NASA Astrophysics Data System (ADS)

Callow, John Nikolaus; Van Niel, Kimberly P.; Boggs, Guy S.

2007-01-01

SummaryMany digital elevation models (DEMs) have difficulty replicating hydrological patterns in flat landscapes. Efforts to improve DEM performance in replicating known hydrology have included a variety of soft (i.e. algorithm-based approaches) and hard techniques, such as " Stream burning" or "surface reconditioning" (e.g. Agree or ANUDEM). Using a representation of the known stream network, these methods trench or mathematically warp the original DEM to improve how accurately stream position, stream length and catchment boundaries replicate known hydrological conditions. However, these techniques permanently alter the DEM and may affect further analyses (e.g. slope). This paper explores the impact that commonly used hydrological correction methods ( Stream burning, Agree.aml and ANUDEM v4.6.3 and ANUDEM v5.1) have on the overall nature of a DEM, finding that different methods produce non-convergent outcomes for catchment parameters (such as catchment boundaries, stream position and length), and differentially compromise secondary terrain analysis. All hydrological correction methods successfully improved calculation of catchment area, stream position and length as compared to using the DEM without any modification, but they all increased catchment slope. No single method performing best across all categories. Different hydrological correction methods changed elevation and slope in different spatial patterns and magnitudes, compromising the ability to derive catchment parameters and conduct secondary terrain analysis from a single DEM. Modification of a DEM to better reflect known hydrology can be useful, however knowledge of the magnitude and spatial pattern of the changes are required before using a DEM for subsequent analyses.

Magnetosphere - Ionosphere - Thermosphere (MIT) Coupling at Jupiter

NASA Astrophysics Data System (ADS)

Yates, J. N.; Ray, L. C.; Achilleos, N.

2017-12-01

Jupiter's upper atmospheric temperature is considerably higher than that predicted by Solar Extreme Ultraviolet (EUV) heating alone. Simulations incorporating magnetosphere-ionosphere coupling effects into general circulation models have, to date, struggled to reproduce the observed atmospheric temperatures under simplifying assumptions such as azimuthal symmetry and a spin-aligned dipole magnetic field. Here we present the development of a full three-dimensional thermosphere model coupled in both hemispheres to an axisymmetric magnetosphere model. This new coupled model is based on the two-dimensional MIT model presented in Yates et al., 2014. This coupled model is a critical step towards to the development of a fully coupled 3D MIT model. We discuss and compare the resulting thermospheric flows, energy balance and MI coupling currents to those presented in previous 2D MIT models.

Historisches Rätsel Physik mit Gewehr und Eiern

NASA Astrophysics Data System (ADS)

Loos, Andreas

2003-11-01

Es fing schon gut an: Mit zehn Jahren saß der begabte Junge bereits in der Universität, wo ihn kein Geringerer als sein Vater persönlich unterrichtete. Damit schlug dieser zwei Fliegen mit einer Klappe: Sein Sohn lernte etwas Gescheites, und er war zugleich in sicherer Obhut.

Smartes System für die Energiewende - der Übertragungsnetzbetreiber in der digitalen Zukunft

NASA Astrophysics Data System (ADS)

Pflaum, Rainer; Egeler, Tobias

Die Übertragungsnetze stellen eine zuverlässige Versorgung von Haushalt, Gewerbe und Industrie mit elektrischer Energie sicher und sind damit Grundlage einer modernen Wirtschaft und Gesellschaft. Die mittlerweile unumkehrbaren Entwicklungen der nationalen und europäischen Energiewende stellen den Übertragungsnetzbetreiber in seinen Kernaufgaben, dem Bau und Betrieb von Netzen, dem Markt- und Netzzugang und der Integration der erneuerbaren Energien vor neue und große Herausforderungen. Verbrauchsnahe dezentrale Erzeugung wie verbrauchsferne zentrale Erzeugung muss im Sinne der Gewährleistung der Systemstabilität gemanagt und in Einklang mit dem Verbrauch gebracht werden. Erneuerbare Energien müssen zudem in einem solchen System ihren Beitrag zur System- und Marktintegration leisten. All das erfordert mehr Daten, um in einem Gesamtsystem dynamische Reaktionsmöglichkeiten gewährleisten zu können. Erst die "Digitalisierung" schafft dabei die notwendigen Voraussetzungen die Komplexität zu stemmen. Die Digitalisierung stellt daher ein Kernelement dieses Wandels des Übertragungsnetzbetreibers dar, die einerseits mit zum Entstehen der neuen Herausforderungen beiträgt, andererseits aber auch hilft Werkzeuge bereitzustellen, diesen Herausforderungen zu begegnen. Im folgenden Beitrag wird aufgezeigt, wie die Digitalisierung die Aufgaben und Instrumente des Übertragungsnetzbetreibers verändern. Ausgehend von den heutigen Aufgaben eines Übertragungsnetzbetreibers und dem gültigen Rechtsrahmen werden unter dem Begriff "Notwendiges Set für morgen" smarte Elemente und Werkzeuge beschrieben, die bereits heute im Einsatz sind oder in den nächsten Jahren notwendig werden. Im Anschluss erfolgt anhand einiger Beispiele aus unterschiedlichen Bereichen eine Konkretisierung der Einsatzzwecke der Digitalisierung beim Übertragungsnetzbetreiber. Ein kurzer Ausblick mit Fokus auf den weiteren Veränderungsprozess rundet den Beitrag ab.

A simplified DEM-CFD approach for pebble bed reactor simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Y.; Ji, W.

In pebble bed reactors (PBR's), the pebble flow and the coolant flow are coupled with each other through coolant-pebble interactions. Approaches with different fidelities have been proposed to simulate similar phenomena. Coupled Discrete Element Method-Computational Fluid Dynamics (DEM-CFD) approaches are widely studied and applied in these problems due to its good balance between efficiency and accuracy. In this work, based on the symmetry of the PBR geometry, a simplified 3D-DEM/2D-CFD approach is proposed to speed up the DEM-CFD simulation without significant loss of accuracy. Pebble flow is simulated by a full 3-D DEM, while the coolant flow field is calculatedmore » with a 2-D CFD simulation by averaging variables along the annular direction in the cylindrical geometry. Results show that this simplification can greatly enhance the efficiency for cylindrical core, which enables further inclusion of other physics such as thermal and neutronic effect in the multi-physics simulations for PBR's. (authors)« less

Enhanced ASTER DEMs for Decadal Measurements of Glacier Elevation Changes

NASA Astrophysics Data System (ADS)

Girod, L.; Nuth, C.; Kääb, A.

2016-12-01

Elevation change data is critical to the understanding of a number of geophysical processes, including glaciers through the measurement their volume change. The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) system on-board the Terra (EOS AM-1) satellite has been a unique source of systematic stereoscopic images covering the whole globe at 15m resolution and at a consistent quality for over 15 years. While satellite stereo sensors with significantly improved radiometric and spatial resolution are available today, the potential of ASTER data lies in its long consistent time series that is unrivaled, though not fully exploited for change analysis due to lack of data accuracy and precision. ASTER data are strongly affected by attitude jitter, mainly of approximately 4 and 30 km wavelength, and improving the generation of ASTER DEMs requires removal of this effect. We developed MMASTER, an improved method for ASTER DEM generation and implemented it in the open source photogrammetric library and software suite MicMac. The method relies on the computation of a rational polynomial coefficients (RPC) model and the detection and correction of cross-track sensor jitter in order to compute DEMs. Our sensor modeling does not require ground control points and thus potentially allows for automatic processing of large data volumes. When compared to ground truth data, we have assessed a ±5m accuracy in DEM differencing when using our processing method, improved from the ±30m when using the AST14DMO DEM product. We demonstrate and discuss this improved ASTER DEM quality for a number of glaciers in Greenland (See figure attached), Alaska, and Svalbard. The quality of our measurements promises to further unlock the underused potential of ASTER DEMs for glacier volume change time series on a global scale. The data produced by our method will thus help to better understand the response of glaciers to climate change and their influence on runoff and sea level.

Analysis of ArcticDEM orthorectification for polar navigational traverses

NASA Astrophysics Data System (ADS)

Menio, E. C.; Deeb, E. J.; Weale, J.; Courville, Z.; Tracy, B.; Cloutier, M. D.; Cothren, J. D.; Liu, J.

2017-12-01

The availability and accessibility of high-resolution satellite imagery allows operational support teams to visually assess physical risks along traverse routes before and during the field season. In support of operations along the Greenland Inland Traverse (GrIT), DigitalGlobe's WorldView 0.5m resolution panchromatic imagery is analyzed to identify and digitize crevasse features along the route from Thule Air Force Base to Summit Station, Greenland. In the spring of 2016, field teams reported up to 150 meters of offset between the location of crevasse features on the ground and the location of the same feature on the imagery provided. Investigation into this issue identified the need to orthorectify imagery—use digital elevation models (DEMs) to correct viewing geometry distortions—to improve navigational accuracy in the field. It was previously thought that orthorectification was not necessary for applications in relatively flat terrain such as ice sheets. However, the surface elevations on the margins of the Greenland Ice Sheet vary enough to cause distortions in imagery, if taken obliquely. As is standard for requests, the Polar Geospatial Center (PGC) provides orthorectified imagery using the MEaSUREs Greenland Ice Mapping Project (GIMP) 30m digital elevation model. Current, higher-resolution elevation datasets, such as the ArcticDEM (2-5m resolution) and WorldView stereopair DEMs (2-3m resolution), are available for use in orthorectification. This study examines three heavily crevassed areas along the GrIT traverse, as identified in 2015 and 2016 imagery. We extracted elevation profiles along the GrIT route from each of the three DEMs: GIMP, ArcticDEM, and WorldView stereopair mosaic. Results show the courser GIMP data deviating significantly from the ArcticDEM and WorldView data, at points by up to 80m, which is seen as offset of features in plan view. In-situ Ground Penetrating Radar (GPR) surveys of crevasse crossings allow for evaluation of

The Oracle of DEM

NASA Astrophysics Data System (ADS)

Gayley, Kenneth

2013-06-01

The predictions of the famous Greek oracle of Delphi were just ambiguous enough to seem to convey information, yet the user was only seeing their own thoughts. Are there ways in which X-ray spectral analysis is like that oracle? It is shown using heuristic, generic response functions to mimic actual spectral inversion that the widely known ill conditioning, which makes formal inversion impossible in the presence of random noise, also makes a wide variety of different source distributions (DEMs) produce quite similar X-ray continua and resonance-line fluxes. Indeed, the sole robustly inferable attribute for a thermal, optically thin resonance-line spectrum with normal abundances in CIE is its average temperature. The shape of the DEM distribution, on the other hand, is not well constrained, and may actually depend more on the analysis method, no matter how sophisticated, than on the source plasma. The case is made that X-ray spectra can tell us average temperature, and metallicity, and absorbing column, but the main thing it cannot tell us is the main thing it is most often used to infer: the differential emission measure distribution.

AMANDA and D0 as a Test Environment for the LHC Computing Grid (in German)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harenberg, Torsten

2005-08-01

Die Suche nach den Grundbausteinen der Materie und nach den Kräften, die zwischen ihnen wirken, ist das Forschungsgebiet der Hochenergiephysik. Mit immer größer werdenden Teilchenbeschleunigern erreicht man immer tiefer gehende Erkenntnisse und dringt dabei in Energiebereiche vor, wie sie kurz nach dem Urknall herrschten. Im Moment ist das Tevatron am Fermilab der energ piereichste Teilchenbeschleuniger der Welt mit einer Schwerpunktsenergie von √s = 1, 96 TeV. Um die bei diesen hohen Energien entstehende Anzahl von Teilchen zu messen, sind auch immer höher auflösende Detektoren nötig. Dem wurde dadurch Rechnung getragen, dass mit der Steigerung der Schwerpunktsenergie am Tevatron auch diemore » Detektoren DØ und CDF1) teilweise erneuert wurden.« less

Monitoring lava dome changes by means of differential DEMs from TanDEM-X interferometry: Examples from Merapi, Indonesia and Volcán de Colima, Mexico

NASA Astrophysics Data System (ADS)

Kubanek, J.; Westerhaus, M.; Heck, B.

2013-12-01

Estimating the amount of erupted material during a volcanic crisis is one of the major challenges in volcano research. One way to do this and to discriminate between juvenile and non-juvenile fraction is to assess topographic changes before and after an eruption while using area-wide 3D data. LiDAR or other airborne systems may be a good source, but the recording fails when clouds due to volcanic activity obstruct the sight. In addition, costs as well as logistics are high for local observatories. When dealing with dome-building volcanoes, acquiring the data gets further complicated. As the volcano dome can change rapidly in active phases, it is nearly impossible to collect data at the right time. However, when dealing with gross volume change estimates, at least two data sets - taken directly before and after the eruption - are essential. The innovative German Earth observation mission TanDEM-X (TerraSAR-X add-on for Digital Elevation Measurement) is of great importance to overcome some of these problems. The two almost identical radar satellites TerraSAR-X and TanDEM-X fly in a close formation, thus recording images of the same place on the Earth surface at the same time (bistatic mode). As the radar signal penetrates clouds, digital elevation models (DEMs) of the area of investigation can be generated without problems even with cloud cover. A time series analysis of the differential DEMs therefore opens the possibility to assess volume changes at active lava domes. We choose Merapi in Indonesia and Volcán de Colima in Mexico as test sites. Both volcanoes reside in a state of long term effusive eruption, interrupted every few years by phases of dome destruction, generation of pyroclastic flows and deposition of volcanic material. The availability of extensive ground truth data for both test sites further enables to validate the spaceborne data and results. Here, we analyze lava dome changes due to the hazardous Merapi 2010 eruption. We show a series of DEMs

Volcanic geomorphology using TanDEM-X

NASA Astrophysics Data System (ADS)

Poland, Michael; Kubanek, Julia

2016-04-01

Topography is perhaps the most fundamental dataset for any volcano, yet is surprisingly difficult to collect, especially during the course of an eruption. For example, photogrammetry and lidar are time-intensive and often expensive, and they cannot be employed when the surface is obscured by clouds. Ground-based surveys can operate in poor weather but have poor spatial resolution and may expose personnel to hazardous conditions. Repeat passes of synthetic aperture radar (SAR) data provide excellent spatial resolution, but topography in areas of surface change (from vegetation swaying in the wind to physical changes in the landscape) between radar passes cannot be imaged. The German Space Agency's TanDEM-X satellite system, however, solves this issue by simultaneously acquiring SAR data of the surface using a pair of orbiting satellites, thereby removing temporal change as a complicating factor in SAR-based topographic mapping. TanDEM-X measurements have demonstrated exceptional value in mapping the topography of volcanic environments in as-yet limited applications. The data provide excellent resolution (down to ~3-m pixel size) and are useful for updating topographic data at volcanoes where surface change has occurred since the most recent topographic dataset was collected. Such data can be used for applications ranging from correcting radar interferograms for topography, to modeling flow pathways in support of hazards mitigation. The most valuable contributions, however, relate to calculating volume changes related to eruptive activity. For example, limited datasets have provided critical measurements of lava dome growth and collapse at volcanoes including Merapi (Indonesia), Colima (Mexico), and Soufriere Hills (Montserrat), and of basaltic lava flow emplacement at Tolbachik (Kamchatka), Etna (Italy), and Kīlauea (Hawai`i). With topographic data spanning an eruption, it is possible to calculate eruption rates - information that might not otherwise be available

Influence of Terraced area DEM Resolution on RUSLE LS Factor

NASA Astrophysics Data System (ADS)

Zhang, Hongming; Baartman, Jantiene E. M.; Yang, Xiaomei; Gai, Lingtong; Geissen, Viollette

2017-04-01

Topography has a large impact on the erosion of soil by water. Slope steepness and slope length are combined (the LS factor) in the universal soil-loss equation (USLE) and its revised version (RUSLE) for predicting soil erosion. The LS factor is usually extracted from a digital elevation model (DEM). The grid size of the DEM will thus influence the LS factor and the subsequent calculation of soil loss. Terracing is considered as a support practice factor (P) in the USLE/RUSLE equations, which is multiplied with the other USLE/RUSLE factors. However, as terraces change the slope length and steepness, they also affect the LS factor. The effect of DEM grid size on the LS factor has not been investigated for a terraced area. We obtained a high-resolution DEM by unmanned aerial vehicles (UAVs) photogrammetry, from which the slope steepness, slope length, and LS factor were extracted. The changes in these parameters at various DEM resolutions were then analysed. The DEM produced detailed LS-factor maps, particularly for low LS factors. High (small valleys, gullies, and terrace ridges) and low (flats and terrace fields) spatial frequencies were both sensitive to changes in resolution, so the areas of higher and lower slope steepness both decreased with increasing grid size. Average slope steepness decreased and average slope length increased with grid size. Slope length, however, had a larger effect than slope steepness on the LS factor as the grid size varied. The LS factor increased when the grid size increased from 0.5 to 30-m and increased significantly at grid sizes >5-m. The LS factor was increasingly overestimated as grid size decreased. The LS factor decreased from grid sizes of 30 to 100-m, because the details of the terraced terrain were gradually lost, but the factor was still overestimated.

Accuracy assessment of the global TanDEM-X Digital Elevation Model with GPS data

NASA Astrophysics Data System (ADS)

Wessel, Birgit; Huber, Martin; Wohlfart, Christian; Marschalk, Ursula; Kosmann, Detlev; Roth, Achim

2018-05-01

The primary goal of the German TanDEM-X mission is the generation of a highly accurate and global Digital Elevation Model (DEM) with global accuracies of at least 10 m absolute height error (linear 90% error). The global TanDEM-X DEM acquired with single-pass SAR interferometry was finished in September 2016. This paper provides a unique accuracy assessment of the final TanDEM-X global DEM using two different GPS point reference data sets, which are distributed across all continents, to fully characterize the absolute height error. Firstly, the absolute vertical accuracy is examined by about three million globally distributed kinematic GPS (KGPS) points derived from 19 KGPS tracks covering a total length of about 66,000 km. Secondly, a comparison is performed with more than 23,000 "GPS on Bench Marks" (GPS-on-BM) points provided by the US National Geodetic Survey (NGS) scattered across 14 different land cover types of the US National Land Cover Data base (NLCD). Both GPS comparisons prove an absolute vertical mean error of TanDEM-X DEM smaller than ±0.20 m, a Root Means Square Error (RMSE) smaller than 1.4 m and an excellent absolute 90% linear height error below 2 m. The RMSE values are sensitive to land cover types. For low vegetation the RMSE is ±1.1 m, whereas it is slightly higher for developed areas (±1.4 m) and for forests (±1.8 m). This validation confirms an outstanding absolute height error at 90% confidence level of the global TanDEM-X DEM outperforming the requirement by a factor of five. Due to its extensive and globally distributed reference data sets, this study is of considerable interests for scientific and commercial applications.

Dem Generation from Close-Range Photogrammetry Using Extended Python Photogrammetry Toolbox

NASA Astrophysics Data System (ADS)

Belmonte, A. A.; Biong, M. M. P.; Macatulad, E. G.

2017-10-01

Digital elevation models (DEMs) are widely used raster data for different applications concerning terrain, such as for flood modelling, viewshed analysis, mining, land development, engineering design projects, to name a few. DEMs can be obtained through various methods, including topographic survey, LiDAR or photogrammetry, and internet sources. Terrestrial close-range photogrammetry is one of the alternative methods to produce DEMs through the processing of images using photogrammetry software. There are already powerful photogrammetry software that are commercially-available and can produce high-accuracy DEMs. However, this entails corresponding cost. Although, some of these software have free or demo trials, these trials have limits in their usable features and usage time. One alternative is the use of free and open-source software (FOSS), such as the Python Photogrammetry Toolbox (PPT), which provides an interface for performing photogrammetric processes implemented through python script. For relatively small areas such as in mining or construction excavation, a relatively inexpensive, fast and accurate method would be advantageous. In this study, PPT was used to generate 3D point cloud data from images of an open pit excavation. The PPT was extended to add an algorithm converting the generated point cloud data into a usable DEM.

Validation of digital elevation models (DEMs) and comparison of geomorphic metrics on the southern Central Andean Plateau

NASA Astrophysics Data System (ADS)

Purinton, Benjamin; Bookhagen, Bodo

2017-04-01

In this study, we validate and compare elevation accuracy and geomorphic metrics of satellite-derived digital elevation models (DEMs) on the southern Central Andean Plateau. The plateau has an average elevation of 3.7 km and is characterized by diverse topography and relief, lack of vegetation, and clear skies that create ideal conditions for remote sensing. At 30 m resolution, SRTM-C, ASTER GDEM2, stacked ASTER L1A stereopair DEM, ALOS World 3D, and TanDEM-X have been analyzed. The higher-resolution datasets include 12 m TanDEM-X, 10 m single-CoSSC TerraSAR-X/TanDEM-X DEMs, and 5 m ALOS World 3D. These DEMs are state of the art for optical (ASTER and ALOS) and radar (SRTM-C and TanDEM-X) spaceborne sensors. We assessed vertical accuracy by comparing standard deviations of the DEM elevation versus 307 509 differential GPS measurements across 4000 m of elevation. For the 30 m DEMs, the ASTER datasets had the highest vertical standard deviation at > 6.5 m, whereas the SRTM-C, ALOS World 3D, and TanDEM-X were all < 3.5 m. Higher-resolution DEMs generally had lower uncertainty, with both the 12 m TanDEM-X and 5 m ALOS World 3D having < 2 m vertical standard deviation. Analysis of vertical uncertainty with respect to terrain elevation, slope, and aspect revealed the low uncertainty across these attributes for SRTM-C (30 m), TanDEM-X (12-30 m), and ALOS World 3D (5-30 m). Single-CoSSC TerraSAR-X/TanDEM-X 10 m DEMs and the 30 m ASTER GDEM2 displayed slight aspect biases, which were removed in their stacked counterparts (TanDEM-X and ASTER Stack). Based on low vertical standard deviations and visual inspection alongside optical satellite data, we selected the 30 m SRTM-C, 12-30 m TanDEM-X, 10 m single-CoSSC TerraSAR-X/TanDEM-X, and 5 m ALOS World 3D for geomorphic metric comparison in a 66 km2 catchment with a distinct river knickpoint. Consistent m/n values were found using chi plot channel profile analysis, regardless of DEM type and spatial resolution. Slope, curvature

An algorithm to extract more accurate stream longitudinal profiles from unfilled DEMs

NASA Astrophysics Data System (ADS)

Byun, Jongmin; Seong, Yeong Bae

2015-08-01

Morphometric features observed from a stream longitudinal profile (SLP) reflect channel responses to lithological variation and changes in uplift or climate; therefore, they constitute essential indicators in the studies for the dynamics between tectonics, climate, and surface processes. The widespread availability of digital elevation models (DEMs) and their processing enable semi-automatic extraction of SLPs as well as additional stream profile parameters, thus reducing the time spent for extracting them and simultaneously allowing regional-scale studies of SLPs. However, careful consideration is required to extract SLPs directly from a DEM, because the DEM must be altered by depression filling process to ensure the continuity of flows across it. Such alteration inevitably introduces distortions to the SLP, such as stair steps, bias of elevation values, and inaccurate stream paths. This paper proposes a new algorithm, called maximum depth tracing algorithm (MDTA), to extract more accurate SLPs using depression-unfilled DEMs. The MDTA supposes that depressions in DEMs are not necessarily artifacts to be removed, and that elevation values within them are useful to represent more accurately the real landscape. To ensure the continuity of flows even across the unfilled DEM, the MDTA first determines the outlet of each depression and then reverses flow directions of the cells on the line of maximum depth within each depression, beginning from the outlet and toward the sink. It also calculates flow accumulation without disruption across the unfilled DEM. Comparative analysis with the profiles extracted by the hydrologic functions implemented in the ArcGIS™ was performed to illustrate the benefits from the MDTA. It shows that the MDTA provides more accurate stream paths on depression areas, and consequently reduces distortions of the SLPs derived from the paths, such as exaggerated elevation values and negatively biased slopes that are commonly observed in the SLPs

Uncertainty Assessment and Weight Map Generation for Efficient Fusion of Tandem-X and CARTOSAT-1 Dems

NASA Astrophysics Data System (ADS)

Bagheri, H.; Schmitt, M.; Zhu, X. X.

2017-05-01

Recently, with InSAR data provided by the German TanDEM-X mission, a new global, high-resolution Digital Elevation Model (DEM) has been produced by the German Aerospace Center (DLR) with unprecedented height accuracy. However, due to SAR-inherent sensor specifics, its quality decreases over urban areas, making additional improvement necessary. On the other hand, DEMs derived from optical remote sensing imagery, such as Cartosat-1 data, have an apparently greater resolution in urban areas, making their fusion with TanDEM-X elevation data a promising perspective. The objective of this paper is two-fold: First, the height accuracies of TanDEM-X and Cartosat-1 elevation data over different land types are empirically evaluated in order to analyze the potential of TanDEM-XCartosat- 1 DEM data fusion. After the quality assessment, urban DEM fusion using weighted averaging is investigated. In this experiment, both weight maps derived from the height error maps delivered with the DEM data, as well as more sophisticated weight maps predicted by a procedure based on artificial neural networks (ANNs) are compared. The ANN framework employs several features that can describe the height residual performance to predict the weights used in the subsequent fusion step. The results demonstrate that especially the ANN-based framework is able to improve the quality of the final DEM through data fusion.

Helicobacter sp. MIT 01-6451 infection during fetal and neonatal life in laboratory mice.

PubMed

Yamanaka, Hitoki; Nakanishi, Tai; Takagi, Toshikazu; Ohsawa, Makiko; Kubo, Noriaki; Yamamoto, Naoto; Takemoto, Takahira; Ohsawa, Kazutaka

2015-01-01

Helicobacter sp. MIT 01-6451 has been detected in SPF mice kept in Japan. To characterize strain MIT 01-6451, its infection route during fetal and neonatal life and effects on pregnancy were investigated using immunocompetent and immunodeficient mouse strains (BALB/c, C57BL/6, and SCID). MIT 01-6451 was detected in the uterus, vagina, and mammary glands of 50% of infected SCID mice, whereas these tissues were all negative in immunocompetent mice. No fetal infections with MIT 01-6451 were detected at 16-18 days after pregnancy in any mouse strain. In newborn mice, MIT 01-6451 was detected in intestinal tissue of C57BL/6 and SCID mice at 9-11 days after birth, but not in BALB/c mice. The IgA and IgG titers to MIT 01-6451 in sera of C57BL/6 female mice were significantly lower than those of BALB/c mice. Although no significant differences in the number of newborns per litter were observed between MIT 01-6451-infected and MIT 01-6451-free dams, the birth rate was lower in infected SCID mice than in control SCID mice. The present results indicated that MIT 01-6451 infects newborn mice after birth rather than by vertical transmission to the fetus via the placenta and that MIT 01-6451 infection shows opportunistically negative effects on the birth rate. In addition, the maternal immune response may affect infection of newborn mice with MIT 01-6451 through breast milk.

Helicobacter sp. MIT 01-6451 infection during fetal and neonatal life in laboratory mice

PubMed Central

Yamanaka, Hitoki; Nakanishi, Tai; Takagi, Toshikazu; Ohsawa, Makiko; Kubo, Noriaki; Yamamoto, Naoto; Takemoto, Takahira; Ohsawa, Kazutaka

2015-01-01

Helicobacter sp. MIT 01-6451 has been detected in SPF mice kept in Japan. To characterize strain MIT 01-6451, its infection route during fetal and neonatal life and effects on pregnancy were investigated using immunocompetent and immunodeficient mouse strains (BALB/c, C57BL/6, and SCID). MIT 01-6451 was detected in the uterus, vagina, and mammary glands of 50% of infected SCID mice, whereas these tissues were all negative in immunocompetent mice. No fetal infections with MIT 01-6451 were detected at 16–18 days after pregnancy in any mouse strain. In newborn mice, MIT 01-6451 was detected in intestinal tissue of C57BL/6 and SCID mice at 9–11 days after birth, but not in BALB/c mice. The IgA and IgG titers to MIT 01-6451 in sera of C57BL/6 female mice were significantly lower than those of BALB/c mice. Although no significant differences in the number of newborns per litter were observed between MIT 01-6451-infected and MIT 01-6451-free dams, the birth rate was lower in infected SCID mice than in control SCID mice. The present results indicated that MIT 01-6451 infects newborn mice after birth rather than by vertical transmission to the fetus via the placenta and that MIT 01-6451 infection shows opportunistically negative effects on the birth rate. In addition, the maternal immune response may affect infection of newborn mice with MIT 01-6451 through breast milk. PMID:26134357

Evaluation of the MIT RMID 1000 system for the identification of Listeria species.

PubMed

Ricardi, John; Haavig, David; Cruz, Lasaunta; Paoli, George; Gehring, Andrew

2010-01-01

The Micro Imaging Technology (MIT) 1000 Rapid Microbial Identification (RMID) System is a device that uses the principles of light scattering coupled with proprietary algorithms to identify bacteria after being cultured and placed in a vial of filtered water. This specific method is for pure culture identification of Listeria spp. A total of 81 microorganisms (55 isolates) were tested by the MIT 1000 System, of which 25 were Listeria spp. and 30 a variety of other bacterial species. In addition, a total of 406 tests over seven different ruggedness parameters were tested by the MIT 1000 System to determine its flexibility to the specifications stated in the MIT 1000 System User Guide in areas where they might be deviated by a user to shorten the test cycle. Overall, MIT concluded that the MIT 1000 System had an accuracy performance that should certify this Performance Test Method for the identification of Listeria spp. This report discusses the tests performed, results achieved, and conclusions, along with several reference documents to enable a higher understanding of the technology used by the MIT 1000 System.

Dem Local Accuracy Patterns in Land-Use/Land-Cover Classification

NASA Astrophysics Data System (ADS)

Katerji, Wassim; Farjas Abadia, Mercedes; Morillo Balsera, Maria del Carmen

2016-01-01

Global and nation-wide DEM do not preserve the same height accuracy throughout the area of study. Instead of assuming a single RMSE value for the whole area, this study proposes a vario-model that divides the area into sub-regions depending on the land-use / landcover (LULC) classification, and assigns a local accuracy per each zone, as these areas share similar terrain formation and roughness, and tend to have similar DEM accuracies. A pilot study over Lebanon using the SRTM and ASTER DEMs, combined with a set of 1,105 randomly distributed ground control points (GCPs) showed that even though the inputDEMs have different spatial and temporal resolution, and were collected using difierent techniques, their accuracy varied similarly when changing over difierent LULC classes. Furthermore, validating the generated vario-models proved that they provide a closer representation of the accuracy to the validating GCPs than the conventional RMSE, by 94% and 86% for the SRTMand ASTER respectively. Geostatistical analysis of the input and output datasets showed that the results have a normal distribution, which support the generalization of the proven hypothesis, making this finding applicable to other input datasets anywhere around the world.

High-Accuracy Tidal Flat Digital Elevation Model Construction Using TanDEM-X Science Phase Data

NASA Technical Reports Server (NTRS)

Lee, Seung-Kuk; Ryu, Joo-Hyung

2017-01-01

This study explored the feasibility of using TanDEM-X (TDX) interferometric observations of tidal flats for digital elevation model (DEM) construction. Our goal was to generate high-precision DEMs in tidal flat areas, because accurate intertidal zone data are essential for monitoring coastal environment sand erosion processes. To monitor dynamic coastal changes caused by waves, currents, and tides, very accurate DEMs with high spatial resolution are required. The bi- and monostatic modes of the TDX interferometer employed during the TDX science phase provided a great opportunity for highly accurate intertidal DEM construction using radar interferometry with no time lag (bistatic mode) or an approximately 10-s temporal baseline (monostatic mode) between the master and slave synthetic aperture radar image acquisitions. In this study, DEM construction in tidal flat areas was first optimized based on the TDX system parameters used in various TDX modes. We successfully generated intertidal zone DEMs with 57-m spatial resolutions and interferometric height accuracies better than 0.15 m for three representative tidal flats on the west coast of the Korean Peninsula. Finally, we validated these TDX DEMs against real-time kinematic-GPS measurements acquired in two tidal flat areas; the correlation coefficient was 0.97 with a root mean square error of 0.20 m.

Analysis the Accuracy of Digital Elevation Model (DEM) for Flood Modelling on Lowland Area

NASA Astrophysics Data System (ADS)

Zainol Abidin, Ku Hasna Zainurin Ku; Razi, Mohd Adib Mohammad; Bukari, Saifullizan Mohd

2018-04-01

Flood is one type of natural disaster that occurs almost every year in Malaysia. Commonly the lowland areas are the worst affected areas. This kind of disaster is controllable by using an accurate data for proposing any kinds of solutions. Elevation data is one of the data used to produce solutions for flooding. Currently, the research about the application of Digital Elevation Model (DEM) in hydrology was increased where this kind of model will identify the elevation for required areas. University of Tun Hussein Onn Malaysia is one of the lowland areas which facing flood problems on 2006. Therefore, this area was chosen in order to produce DEM which focussed on University Health Centre (PKU) and drainage area around Civil and Environment Faculty (FKAAS). Unmanned Aerial Vehicle used to collect aerial photos data then undergoes a process of generating DEM according to three types of accuracy and quality from Agisoft PhotoScan software. The higher the level of accuracy and quality of DEM produced, the longer time taken to generate a DEM. The reading of the errors created while producing the DEM shows almost 0.01 different. Therefore, it has been identified there are some important parameters which influenced the accuracy of DEM.

Relative Error Evaluation to Typical Open Global dem Datasets in Shanxi Plateau of China

NASA Astrophysics Data System (ADS)

Zhao, S.; Zhang, S.; Cheng, W.

2018-04-01

Produced by radar data or stereo remote sensing image pairs, global DEM datasets are one of the most important types for DEM data. Relative error relates to surface quality created by DEM data, so it relates to geomorphology and hydrologic applications using DEM data. Taking Shanxi Plateau of China as the study area, this research evaluated the relative error to typical open global DEM datasets including Shuttle Radar Terrain Mission (SRTM) data with 1 arc second resolution (SRTM1), SRTM data with 3 arc second resolution (SRTM3), ASTER global DEM data in the second version (GDEM-v2) and ALOS world 3D-30m (AW3D) data. Through process and selection, more than 300,000 ICESat/GLA14 points were used as the GCP data, and the vertical error was computed and compared among four typical global DEM datasets. Then, more than 2,600,000 ICESat/GLA14 point pairs were acquired using the distance threshold between 100 m and 500 m. Meanwhile, the horizontal distance between every point pair was computed, so the relative error was achieved using slope values based on vertical error difference and the horizontal distance of the point pairs. Finally, false slope ratio (FSR) index was computed through analyzing the difference between DEM and ICESat/GLA14 values for every point pair. Both relative error and FSR index were categorically compared for the four DEM datasets under different slope classes. Research results show: Overall, AW3D has the lowest relative error values in mean error, mean absolute error, root mean square error and standard deviation error; then the SRTM1 data, its values are a little higher than AW3D data; the SRTM3 and GDEM-v2 data have the highest relative error values, and the values for the two datasets are similar. Considering different slope conditions, all the four DEM data have better performance in flat areas but worse performance in sloping regions; AW3D has the best performance in all the slope classes, a litter better than SRTM1; with slope increasing

a High Precision dem Extraction Method Based on Insar Data

NASA Astrophysics Data System (ADS)

Wang, Xinshuang; Liu, Lingling; Shi, Xiaoliang; Huang, Xitao; Geng, Wei

2018-04-01

In the 13th Five-Year Plan for Geoinformatics Business, it is proposed that the new InSAR technology should be applied to surveying and mapping production, which will become the innovation driving force of geoinformatics industry. This paper will study closely around the new outline of surveying and mapping and then achieve the TerraSAR/TanDEM data of Bin County in Shaanxi Province in X band. The studying steps are as follows; Firstly, the baseline is estimated from the orbital data; Secondly, the interferometric pairs of SAR image are accurately registered; Thirdly, the interferogram is generated; Fourth, the interferometric correlation information is estimated and the flat-earth phase is removed. In order to solve the phase noise and the discontinuity phase existing in the interferometric image of phase, a GAMMA adaptive filtering method is adopted. Aiming at the "hole" problem of missing data in low coherent area, the interpolation method of low coherent area mask is used to assist the phase unwrapping. Then, the accuracy of the interferometric baseline is estimated from the ground control points. Finally, 1 : 50000 DEM is generated, and the existing DEM data is used to verify the accuracy through statistical analysis. The research results show that the improved InSAR data processing method in this paper can obtain the high-precision DEM of the study area, exactly the same with the topography of reference DEM. The R2 can reach to 0.9648, showing a strong positive correlation.

Evaluating DEM conditioning techniques, elevation source data, and grid resolution for field-scale hydrological parameter extraction

NASA Astrophysics Data System (ADS)

Woodrow, Kathryn; Lindsay, John B.; Berg, Aaron A.

2016-09-01

Although digital elevation models (DEMs) prove useful for a number of hydrological applications, they are often the end result of numerous processing steps that each contains uncertainty. These uncertainties have the potential to greatly influence DEM quality and to further propagate to DEM-derived attributes including derived surface and near-surface drainage patterns. This research examines the impacts of DEM grid resolution, elevation source data, and conditioning techniques on the spatial and statistical distribution of field-scale hydrological attributes for a 12,000 ha watershed of an agricultural area within southwestern Ontario, Canada. Three conditioning techniques, including depression filling (DF), depression breaching (DB), and stream burning (SB), were examined. The catchments draining to each boundary of 7933 agricultural fields were delineated using the surface drainage patterns modeled from LiDAR data, interpolated to a 1 m, 5 m, and 10 m resolution DEMs, and from a 10 m resolution photogrammetric DEM. The results showed that variation in DEM grid resolution resulted in significant differences in the spatial and statistical distributions of contributing areas and the distributions of downslope flowpath length. Degrading the grid resolution of the LiDAR data from 1 m to 10 m resulted in a disagreement in mapped contributing areas of between 29.4% and 37.3% of the study area, depending on the DEM conditioning technique. The disagreements among the field-scale contributing areas mapped from the 10 m LiDAR DEM and photogrammetric DEM were large, with nearly half of the study area draining to alternate field boundaries. Differences in derived contributing areas and flowpaths among various conditioning techniques increased substantially at finer grid resolutions, with the largest disagreement among mapped contributing areas occurring between the 1 m resolution DB DEM and the SB DEM (37% disagreement) and the DB-DF comparison (36.5% disagreement in mapped

A seamless, high-resolution digital elevation model (DEM) of the north-central California coast

USGS Publications Warehouse

Foxgrover, Amy C.; Barnard, Patrick L.

2012-01-01

A seamless, 2-meter resolution digital elevation model (DEM) of the north-central California coast has been created from the most recent high-resolution bathymetric and topographic datasets available. The DEM extends approximately 150 kilometers along the California coastline, from Half Moon Bay north to Bodega Head. Coverage extends inland to an elevation of +20 meters and offshore to at least the 3 nautical mile limit of state waters. This report describes the procedures of DEM construction, details the input data sources, and provides the DEM for download in both ESRI Arc ASCII and GeoTIFF file formats with accompanying metadata.

Optimizing digital elevation models (DEMs) accuracy for planning and design of mobile communication networks

NASA Astrophysics Data System (ADS)

Hassan, Mahmoud A.

2004-02-01

Digital elevation models (DEMs) are important tools in the planning, design and maintenance of mobile communication networks. This research paper proposes a method for generating high accuracy DEMs based on SPOT satellite 1A stereo pair images, ground control points (GCP) and Erdas OrthoBASE Pro image processing software. DEMs with 0.2911 m mean error were achieved for the hilly and heavily populated city of Amman. The generated DEM was used to design a mobile communication network resulted in a minimum number of radio base transceiver stations, maximum number of covered regions and less than 2% of dead zones.

What is the effect of LiDAR-derived DEM resolution on large-scale watershed model results?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ping Yang; Daniel B. Ames; Andre Fonseca

This paper examines the effect of raster cell size on hydrographic feature extraction and hydrological modeling using LiDAR derived DEMs. LiDAR datasets for three experimental watersheds were converted to DEMs at various cell sizes. Watershed boundaries and stream networks were delineated from each DEM and were compared to reference data. Hydrological simulations were conducted and the outputs were compared. Smaller cell size DEMs consistently resulted in less difference between DEM-delineated features and reference data. However, minor differences been found between streamflow simulations resulted for a lumped watershed model run at daily simulations aggregated at an annual average. These findings indicatemore » that while higher resolution DEM grids may result in more accurate representation of terrain characteristics, such variations do not necessarily improve watershed scale simulation modeling. Hence the additional expense of generating high resolution DEM's for the purpose of watershed modeling at daily or longer time steps may not be warranted.« less

Generation of a high-accuracy regional DEM based on ALOS/PRISM imagery of East Antarctica

NASA Astrophysics Data System (ADS)

Shiramizu, Kaoru; Doi, Koichiro; Aoyama, Yuichi

2017-12-01

A digital elevation model (DEM) is used to estimate ice-flow velocities for an ice sheet and glaciers via Differential Interferometric Synthetic Aperture Radar (DInSAR) processing. The accuracy of DInSAR-derived displacement estimates depends upon the accuracy of the DEM. Therefore, we used stereo optical images, obtained with a panchromatic remote-sensing instrument for stereo mapping (PRISM) sensor mounted onboard the Advanced Land Observing Satellite (ALOS), to produce a new DEM ("PRISM-DEM") of part of the coastal region of Lützow-Holm Bay in Dronning Maud Land, East Antarctica. We verified the accuracy of the PRISM-DEM by comparing ellipsoidal heights with those of existing DEMs and values obtained by satellite laser altimetry (ICESat/GLAS) and Global Navigation Satellite System surveying. The accuracy of the PRISM-DEM is estimated to be 2.80 m over ice sheet, 4.86 m over individual glaciers, and 6.63 m over rock outcrops. By comparison, the estimated accuracy of the ASTER-GDEM, widely used in polar regions, is 33.45 m over ice sheet, 14.61 m over glaciers, and 19.95 m over rock outcrops. For displacement measurements made along the radar line-of-sight by DInSAR, in conjunction with ALOS/PALSAR data, the accuracy of the PRISM-DEM and ASTER-GDEM correspond to estimation errors of <6.3 mm and <31.8 mm, respectively.

MERIT DEM: A new high-accuracy global digital elevation model and its merit to global hydrodynamic modeling

NASA Astrophysics Data System (ADS)

Yamazaki, D.; Ikeshima, D.; Neal, J. C.; O'Loughlin, F.; Sampson, C. C.; Kanae, S.; Bates, P. D.

2017-12-01

Digital Elevation Models (DEM) are fundamental data for flood modelling. While precise airborne DEMs are available in developed regions, most parts of the world rely on spaceborne DEMs which include non-negligible height errors. Here we show the most accurate global DEM to date at 90m resolution by eliminating major error components from the SRTM and AW3D DEMs. Using multiple satellite data and multiple filtering techniques, we addressed absolute bias, stripe noise, speckle noise and tree height bias from spaceborne DEMs. After the error removal, significant improvements were found in flat regions where height errors were larger than topography variability, and landscapes features such as river networks and hill-valley structures became clearly represented. We found the topography slope of the previous DEMs was largely distorted in most of world major floodplains (e.g. Ganges, Nile, Niger, Mekong) and swamp forests (e.g. Amazon, Congo, Vasyugan). The developed DEM will largely reduce the uncertainty in both global and regional flood modelling.

CapDEM - Toward a Capability Engineering Process: A Discussion Paper

DTIC Science & Technology

2005-09-01

Mokhtari DRDC Valcartier S. Lam DRDC Ottawa Defence R&D Canada – Valcartier Technical Report DRDC Valcartier TR 2004-230 September 2005 CapDEM...Toward a capability engineering process A discussion paper F. Bernier M. Couture G. Dussault C. Lalancette F. Lemieux M. Lizotte M. Mokhtari DRDC...Lizotte, M., Mokhtari , M. 2005. CapDEM – Toward capability engineering process definition: A discussion paper: A discussion paper. DRDC Valcartier

TerraSAR-X/TanDEM-X data for natural hazards research in mountainous regions of Uzbekistan

NASA Astrophysics Data System (ADS)

Semakova, Eleonora; Bühler, Yves

2017-07-01

Accurate and up-to-date digital elevation models (DEMs) are important tools for studying mountain hazards. We considered natural hazards related to glacier retreat, debris flows, and snow avalanches in two study areas of the Western Tien-Shan mountains, Uzbekistan. High-resolution DEMs were generated using single TerraSAR-X/TanDEM-X datasets. The high quality and actuality of the DEMs were proved through a comparison with Shuttle Radar Topography Mission, Advanced Spaceborne Emission and Reflection Radiometer, and Topo DEMs, using Ice, Cloud, and Land Elevation Satellite data as the reference dataset. For the first study area, which had high levels of economic activity, we applied the generated TanDEM-X DEM to an avalanche dynamics simulation using RAMMS software. Verification of the output results showed good agreement with field observations. For the second study area, with a wide spatial distribution of glaciers, we applied the TanDEM-X DEM to an assessment of glacier surface elevation changes. The results can be used to calculate the local mass balance in glacier ablation zones in other areas. Models were applied to estimate the probability of moraine-dammed lake formation and the affected area of a possible debris flow resulting from glacial lake outburst. The natural hazard research methods considered here will minimize costly ground observations in poorly accessible mountains and mitigate the impacts of hazards on the environment of Uzbekistan.

Mishap Investigation Team (MIT) - Barksdale AFB, Louisiana

NASA Technical Reports Server (NTRS)

Stepaniak, Philip

2005-01-01

The Shuttle Program is organized to support a Shuttle mishap using the resources of the MIT. The afternoon of Feb. 1, 2003, the MIT deployed to Barksdale AFB. This location became the investigative center and interim storage location for crewmembers received from the Lufkin Disaster Field Office (DFO). Working under the leadership of the MIT Lead, the medical team executed a short-term plan that included search, recovery, and identification including coordination with the Armed Forces Institute of Pathology Temporary operations was set up at Barksdale Air Force Base for two weeks. During this time, coordination with the DFO field recovery teams, AFIP personnel, and the crew surgeons was on going. In addition, the crewmember families and NASA management were updated daily. The medical team also dealt with public reports and questions concerning biological and chemical hazards, which were coordinated with SPACEHAB, Inc., Kennedy Space Center (KSC) Medical Operations and the Johnson Space Center (JSC) Space Medicine office. After operations at Barksdale were concluded the medical team transitioned back to Houston and a long-term search, recovery and identification plan was developed.

Evaluation of Airborne l- Band Multi-Baseline Pol-Insar for dem Extraction Beneath Forest Canopy

NASA Astrophysics Data System (ADS)

Li, W. M.; Chen, E. X.; Li, Z. Y.; Jiang, C.; Jia, Y.

2018-04-01

DEM beneath forest canopy is difficult to extract with optical stereo pairs, InSAR and Pol-InSAR techniques. Tomographic SAR (TomoSAR) based on different penetration and view angles could reflect vertical structure and ground structure. This paper aims at evaluating the possibility of TomoSAR for underlying DEM extraction. Airborne L-band repeat-pass Pol-InSAR collected in BioSAR 2008 campaign was applied to reconstruct the 3D structure of forest. And sum of kronecker product and algebraic synthesis algorithm were used to extract ground structure, and phase linking algorithm was applied to estimate ground phase. Then Goldstein cut-branch approach was used to unwrap the phases and then estimated underlying DEM. The average difference between the extracted underlying DEM and Lidar DEM is about 3.39 m in our test site. And the result indicates that it is possible for underlying DEM estimation with airborne L-band repeat-pass TomoSAR technique.

Phylogenetic relationships of the Gomphales based on nuc-25S-rDNA, mit-12S-rDNA, and mit-atp6-DNA combined sequences

Treesearch

Admir J. Giachini; Kentaro Hosaka; Eduardo Nouhra; Joseph Spatafora; James M. Trappe

2010-01-01

Phylogenetic relationships among Geastrales, Gomphales, Hysterangiales, and Phallales were estimated via combined sequences: nuclear large subunit ribosomal DNA (nuc-25S-rDNA), mitochondrial small subunit ribosomal DNA (mit-12S-rDNA), and mitochondrial atp6 DNA (mit-atp6-DNA). Eighty-one taxa comprising 19 genera and 58 species...

Comparison Between 2D and 3D Simulations of Rate Dependent Friction Using DEM

NASA Astrophysics Data System (ADS)

Wang, C.; Elsworth, D.

2017-12-01

Rate-state dependent constitutive laws of frictional evolution have been successful in representing many of the first- and second- order components of earthquake rupture. Although this constitutive law has been successfully applied in numerical models, difficulty remains in efficient implementation of this constitutive law in computationally-expensive granular mechanics simulations using discrete element methods (DEM). This study introduces a novel approach in implementing a rate-dependent constitutive relation of contact friction into DEM. This is essentially an implementation of a slip-weakening constitutive law onto local particle contacts without sacrificing computational efficiency. This implementation allows the analysis of slip stability of simulated fault gouge materials. Velocity-stepping experiments are reported on both uniform and textured distributions of quartz and talc as 3D analogs of gouge mixtures. Distinct local slip stability parameters (a-b) are assigned to the quartz and talc, respectively. We separately vary talc content from 0 to 100% in the uniform mixtures and talc layer thickness from 1 to 20 particles in the textured mixtures. Applied shear displacements are cycled through velocities of 1μm/s and 10μm/s. Frictional evolution data are collected and compared to 2D simulation results. We show that dimensionality significantly impacts the evolution of friction. 3D simulation results are more representative of laboratory observed behavior and numerical noise is shown at a magnitude of 0.01 in terms of friction coefficient. Stability parameters (a-b) can be straightforwardly obtained from analyzing velocity steps, and are different from locally assigned (a-b) values. Sensitivity studies on normal stress, shear velocity, particle size, local (a-b) values, and characteristic slip distance (Dc) show that the implementation is sensitive to local (a-b) values and relations between (Dc) and particle size.

Retrospektive Analyse von Zufallsbefunden, die bei Patienten mit kutanem malignen Malignom durch (18) F-Fluordeoxyglucose-PET/CT erhoben wurden.

PubMed

Conrad, Franziska; Winkens, Thomas; Kaatz, Martin; Goetze, Steven; Freesmeyer, Martin

2016-08-01

Bei der (18) F-Fluordeoxyglucose-Positronenemissionstomographie/Computertomographie (FDG-PET/CT) ergeben sich häufig Zufallsbefunde. In der vorliegenden Studie konzentrierten wir uns auf mittels FDG-PET/CT erhaltene Zufallsbefunde bei Patienten mit kutanem Melanom und überprüften deren Relevanz hinsichtlich weiterer diagnostischer Maßnahmen und Interventionen. Die Krankenakten von 181 konsekutiven Melanom-Patienten wurden retrospektiv ausgewertet, um das Management von Zufallsbefunden zu dokumentieren. Der Schwerpunkt lag dabei auf den histologischen Befunden. Bei 33 von 181 (18 %) Patienten lagen 39 relevante Zufallsbefunde vor, und zwar im Kolorektalbereich (n = 15 Patienten), in der Schilddrüse (n = 8), der Prostata (n = 2), dem Bewegungsapparat (n = 2), in Lymphknoten (n = 2), der Parotis (n = 1), den Mandeln (n = 1), den Nieren (n = 1) und der Gallenblase (n = 1). Bei 25 Patienten schlossen sich weitere diagnostische Verfahren an, wobei in 21 Fällen ein klinisches Korrelat nachgewiesen wurde. Bei 16 von 21 Patienten ergab sich eine Neoplasie, darunter fünf maligne Läsionen (vier Kolonkarzinome und ein Prostatakarzinom). Die Malignome wurden frühzeitig diagnostiziert und in der Mehrzahl der Fälle erfolgreich entfernt. Der Einsatz der FDG-PET/CT als Routine-Diagnostik wird in den Leitlinien empfohlen und ist indiziert bei malignem Melanom ab Stadium IIC. In dieser Studie wurden auf effektive Weise ansonsten nicht erkannte Krebserkrankungen, insbesondere Kolonkarzinome, detektiert. In den meisten Fällen war eine frühe Intervention möglich. Zufallsbefunde durch FDG-PET/CT sollten, unter Berücksichtigung des Zustands und der Wünsche des Patienten, mit den geeigneten diagnostischen Maßnahmen abgeklärt werden. © 2016 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

Hydrologic validation of a structure-from-motion DEM derived from low-altitude UAV imagery

NASA Astrophysics Data System (ADS)

Steiner, Florian; Marzolff, Irene; d'Oleire-Oltmanns, Sebastian

2015-04-01

The increasing ease of use of current Unmanned Aerial Vehicles (UAVs) and 3D image processing software has spurred the number of applications relying on high-resolution topographic datasets. Of particular significance in this field is "structure from motion" (SfM), a photogrammetric technique used to generate low-cost digital elevation models (DEMs) for erosion budgeting, measuring of glaciers/lava-flows, archaeological applications and others. It was originally designed to generate 3D-models of buildings, based on unordered collections of images and has become increasingly common in geoscience applications during the last few years. Several studies on the accuracy of this technique already exist, in which the SfM data is mostly compared with Lidar-generated terrain data. The results are mainly positive, indicating that the technique is suitable for such applications. This work aims at validating very high resolution SfM DEMs with a different approach: Not the original elevation data is validated, but data on terrain-related hydrological and geomorphometric parameters derived from the DEM. The study site chosen for this analysis is an abandoned agricultural field near the city of Taroudant, in the semi-arid southern part of Morocco. The site is characterized by aggressive rill and gully erosion and is - apart from sparsely scattered shrub cover - mainly featureless. An area of 5.7 ha, equipped with 30 high-precision ground control points (GCPs), was covered with an unmanned aerial vehicle (UAV) in two different heights (85 and 170 m). A selection of 160 images was used to generate several high-resolution DEMs (2 and 5 cm resolution) of the area using the fully automated SfM software AGISOFT Photoscan. For comparison purposes, a conventional photogrammetry-based workflow using the Leica Photogrammetry Suite was used to generate a DEM with a resolution of 5 cm (LPS DEM). The evaluation is done by comparison of the SfM DEM with the derived orthoimages and the LPS DEM

Enhancements to TauDEM to support Rapid Watershed Delineation Services

NASA Astrophysics Data System (ADS)

Sazib, N. S.; Tarboton, D. G.

2015-12-01

Watersheds are widely recognized as the basic functional unit for water resources management studies and are important for a variety of problems in hydrology, ecology, and geomorphology. Nevertheless, delineating a watershed spread across a large region is still cumbersome due to the processing burden of working with large Digital Elevation Model. Terrain Analysis Using Digital Elevation Models (TauDEM) software supports the delineation of watersheds and stream networks from within desktop Geographic Information Systems. A rich set of watershed and stream network attributes are computed. However limitations of the TauDEM desktop tools are (1) it supports only one type of raster (tiff format) data (2) requires installation of software for parallel processing, and (3) data have to be in projected coordinate system. This paper presents enhancements to TauDEM that have been developed to extend its generality and support web based watershed delineation services. The enhancements of TauDEM include (1) reading and writing raster data with the open-source geospatial data abstraction library (GDAL) not limited to the tiff data format and (2) support for both geographic and projected coordinates. To support web services for rapid watershed delineation a procedure has been developed for sub setting the domain based on sub-catchments, with preprocessed data prepared for each catchment stored. This allows the watershed delineation to function locally, while extending to the full extent of watersheds using preprocessed information. Additional capabilities of this program includes computation of average watershed properties and geomorphic and channel network variables such as drainage density, shape factor, relief ratio and stream ordering. The updated version of TauDEM increases the practical applicability of it in terms of raster data type, size and coordinate system. The watershed delineation web service functionality is useful for web based software as service deployments

Autolytic activity of human calpain 7 is enhanced by ESCRT-III-related protein IST1 through MIT-MIM interaction.

PubMed

Osako, Yohei; Maemoto, Yuki; Tanaka, Ryohei; Suzuki, Hironori; Shibata, Hideki; Maki, Masatoshi

2010-11-01

Calpain 7, a mammalian ortholog of yeast Cpl1/Rim13 and fungal PalB, is an atypical calpain that lacks a penta-EF-hand domain. Previously, we reported that a region containing a tandem repeat of microtubule-interacting and transport (MIT) domains in calpain 7 interacts with a subset of endosomal sorting complex required for transport (ESCRT)-III-related proteins, suggesting involvement of calpain 7 in the ESCRT system. Although yeast and fungal calpains are thought to be involved in alkaline adaptation via limited proteolysis of specific transcription factors, proteolytic activity of calpain 7 has not been demonstrated yet. In this study, we investigated the interaction between calpain 7 and a newly reported ESCRT-III family member, increased sodium tolerance-1 (IST1), which possesses two different types of MIT-interacting motifs (MIM1 and MIM2). We found that glutathione-S-transferase (GST)-fused tandem MIT domains of calpain 7 (calpain 7MIT) pulled down FLAG-tagged IST1 expressed in HEK293T cells. Coimmunoprecipitation assays with various deletion or point mutants of epitope-tagged calpain 7 and IST1 revealed that both repetitive MIT domains and MIMs are required for efficient interaction. Direct MIT-MIM binding was confirmed by a pulldown experiment with GST-fused IST1 MIM and purified recombinant calpain 7MIT. Furthermore, we found that the GST-MIM protein enhances the autolysis of purified Strep-tagged monomeric green fluorescent protein (mGFP)-fused calpain 7 (mGFP-calpain 7-Strep). The autolysis was almost completely abolished by 10 mmN-ethylmaleimide but only partially inhibited by 1 mm leupeptin or E-64. The putative catalytic Cys290-substituted mutant (mGFP-calpain 7(C290S)-Strep) showed no autolytic activity. These results demonstrate for the first time that human calpain 7 is proteolytically active, and imply that calpain 7 is activated in the ESCRT system. © 2010 The Authors Journal compilation © 2010 FEBS.

No Substitute for Going to the Field: Correcting Lidar DEMs in Salt Marshes

NASA Astrophysics Data System (ADS)

Renken, K.; Morris, J. T.; Lynch, J.; Bayley, H.; Neil, A.; Rasmussen, S.; Tyrrell, M.; Tanis, M.

2016-12-01

Models that forecast the response of salt marshes to current and future trends in sea level rise increasingly are used to guide management of these vulnerable ecosystems. Lidar-derived DEMs serve as the foundation for modeling landform change. However, caution is advised when using these DEMs as the starting point for models of salt marsh evolution. While broad vegetation class (i.e., young forest, old forest, grasslands, desert, etc.) has proven to be a significant predictor of vertical displacement error in terrestrial environments, differentiating error among different species or community types within the same ecosystem has received less attention. Salt marshes are dominated by monocultures of grass species and thus are an ideal environment to examine the within-species effect on lidar DEM error. We analyzed error of lidar DEMs using elevations from real-time kinematic (RTK) surveys in saltmarshes in multiple national parks and wildlife refuge areas from the mouth of the Chesapeake Bay to Massachusetts. Error of the lidar DEMs was sometimes large, on the order of 0.25 m, and varied significantly between sites because vegetation cover varies seasonally and lidar data was not always collected in the same season for each park. Vegetation cover and composition were used to explain differences between RTK elevations and lidar DEMs. This research underscores the importance of collecting RTK elevation data and vegetation cover data coincident with lidar data to produce correction factors specific to individual salt marsh sites.

Astronomie für Alle. Einführung in die Himmelsbeobachtung

NASA Astrophysics Data System (ADS)

Neckel, Thorsten; Neumann, Martin; Staude, Jakob

2002-12-01

Contents: Abenteuer Astronomie - Aufbruch zu fremden Welten. Orientierung am Himmel. Das Teleskop - Dein Blick ins All. Der Erdmond. Wir beobachten unseren Mond. Planeten - Unsere Nachbarn im All. Himmelsleuchten in dunkler Nacht - Das Zodiakallicht. Vagabunden im Sonnensystem. Meteore und Feuerkugeln. Meteorite - Faszinierende Materie aus dem Weltall. Kometen - Eisige Zeugen der Urzeit. Der hellste Stern an unserem Himmel. Auf der Sonne ist 'was los! Kosmische Schattenspiele - Sonnen- und Mondfinsternisse. Ferne Sonnen. Die Tiefen des Kosmos - Sternhaufen, Gasnebel und Galaxien. Astrophotographie mit stehender Kamera. Astrophotographie mit nachgeführter Kamera. Der Kosmos im Computer - Software für Hobbyastronomen. Signale aus dem Kosmos - Radioastronomie für Einsteiger.

Spirituelles Wohlbefinden und Coping bei Sklerodermie, Lupus erythematodes und malignem Melanom.

PubMed

Pilch, Michaela; Scharf, Sabina Nadine; Lukanz, Martin; Wutte, Nora Johanna; Fink-Puches, Regina; Glawischnig-Goschnik, Monika; Unterrainer, Human-Friedrich; Aberer, Elisabeth

2016-07-01

Religiös-spirituelles Wohlbefinden ist verbunden mit höherer Vitalität und verminderter Depressionsneigung. In unserer Studie untersuchten wir die Strategien zur Krankheitsbewältigung und die Rolle von Religiosität-Spiritualität (R-S) zur Verbesserung des subjektiven Wohlbefindens. 149 Patienten (107 Frauen), 44 mit systemischer Sklerodermie (SKL), 48 mit Lupus erythematodes (LE) und 57 mit malignem Melanom (MM), Stadium I-II, wurden mittels eines selbstentwickelten Fragebogens zum subjektiven Wohlbefinden, zu den mit der Erkrankung einhergehenden Umständen sowie mit dem Multidimensionalen Inventar (MI-RSB) zu R-S befragt. LE-Patienten sind zum Zeitpunkt der Diagnosestellung stärker belastet als SKL- und MM-Patienten. SKL- und LE-Patienten können erst nach Jahren die Erkrankung akzeptieren. Der Gesamtscore des religiös-spirituellen Befindens liegt bei LE-Patienten signifikant unter dem Wert der Normalbevölkerung. Fotosensitivität und Gelenksschmerzen sind bei LE-Patienten negativ assoziiert mit der Fähigkeit Vergeben zu können. SKL-Patienten mit Gesichtsveränderungen und Lungenbeteiligung zeigen höhere allgemeine Religiosität. MM-Patienten haben höhere Werte für transzendente Hoffnung. Vorträge über die Krankheit und psychologische Betreuung sind die wichtigsten Bedürfnisse von Patienten mit SKL, LE und MM an ihre Betreuer. Religiös-spirituelle Angebote zur Krankheitsverarbeitung scheinen derzeit eine untergeordnete Rolle zu spielen, könnten aber eine wichtige Ressource sein, der man in Zukunft mehr Aufmerksamkeit schenken sollte. © 2016 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

Publications - PDF 95-33B | Alaska Division of Geological & Geophysical

Science.gov Websites

D->1, C-1, and part of the B-1 quadrangles, east-central Alaska Authors: Clough, J.G., Mull, C.G , Interpretive bedrock geologic map of the Charley River D->1, C-1, and part of the B-1 quadrangles, east-central 1:63,360. http://doi.org/10.14509/1713 Publication Products Maps & Other Oversized Sheets Maps

Description of the Main Ionospheric Trough by the SM-MIT Model. European Longitudinal Sector

NASA Astrophysics Data System (ADS)

Leshchinskaya, T. Yu.; Pustovalova, L. V.

2018-05-01

Due to the selection of exsisting ionospheric models for incorporation into the created System of Ionospheric Monotoring and Prediction of the Russian Federation, the model of the main ionospheric trough (SM-MIT) is tested with the data from ground-based ionospheric observations in the European longitudinal sector. It is shown that the SM-MIT model does not give an increase in accuracy in comparison to the foF2 monthly median upon a description of the equatorial wall of the MIT. The model describes the foF2 values in the MIT minimum with higher accuracy than the foF2 monthly median or the median IRI model; however, at the same time, the deviations of the model foF2 values from the observed values are high enough: 20-30%. In the MIT minimum, the decrease in the model foF2 values relative to the median values is on average only 10%, which is substantially less than the observed depth of MIT in the evening sector. The verification results have shown that the available SM-MIT model must be completed for practical use.

The effects of wavelet compression on Digital Elevation Models (DEMs)

USGS Publications Warehouse

Oimoen, M.J.

2004-01-01

This paper investigates the effects of lossy compression on floating-point digital elevation models using the discrete wavelet transform. The compression of elevation data poses a different set of problems and concerns than does the compression of images. Most notably, the usefulness of DEMs depends largely in the quality of their derivatives, such as slope and aspect. Three areas extracted from the U.S. Geological Survey's National Elevation Dataset were transformed to the wavelet domain using the third order filters of the Daubechies family (DAUB6), and were made sparse by setting 95 percent of the smallest wavelet coefficients to zero. The resulting raster is compressible to a corresponding degree. The effects of the nulled coefficients on the reconstructed DEM are noted as residuals in elevation, derived slope and aspect, and delineation of drainage basins and streamlines. A simple masking technique also is presented, that maintains the integrity and flatness of water bodies in the reconstructed DEM.

[COPD und Klangtherapie: Pilotstudie zur Wirksamkeit einer Behandlung mit Körpertambura bei COPD-Patienten].

PubMed

Hartwig, Bernhard; Schmidt, Stefan; Hartwig, Isabella

2016-01-01

Hintergrund: Erkrankungen der Atemorgane treten mit steigendem Alter öfter auf, nehmen weltweit zu und sind häufige Ursachen für Morbidität und Mortalität. In dieser Pilotstudie wurde der Frage nachgegangen, ob eine einmalige 10-minütige Behandlung mit einer Körpertambura eine signifikante und effektive Verbesserung der Lungenfunktion von Patienten mit chronisch-obstruktiver Lungenerkrankung (COPD; GOLD-Stadium A oder B) erbringen kann. Patienten und Methoden: 54 Probanden konnten je zur Hälfte in eine Behandlungsgruppe (Körpertambura) und eine aktive Kontrollgruppe (Atemtherapie) randomisiert werden. Eine Bestimmung der Lungenfunktionsmessparameter «Einsekundenkapazität» (FEV1) und «inspiratorische Vitalkapazität» (IVC) zu den Zeitpunkten T1 (Baseline), T2 (direkt nach Behandlung) und als Follow-up etwa 3 Wochen nach T1 (T3). Ergebnisse: Die Behandlungsgruppe zeigte sich der Kontrollgruppe in beiden Werten signifikant überlegen. Die Zeit-×-Gruppe-Interaktion (Varianzanalyse) ergab p = 0,001 (FEV1) bzw. p = 0,04 (IVC). Die Behandlungsgruppe zeigte bei beiden Werten eine Verbesserung von klinischer Relevanz. Schlussfolgerung: Diese Ergebnisse zeigen, dass die Klangbehandlung mittels einer Körpertambura - neben den schulmedizinischen, leitliniengerechten Therapien - eine zusätzliche, nebenwirkungsarme, aber durchaus klinisch wirksame Option für die Behandlung von COPD-Patienten darstellen kann, um deren Lebensqualität zu stabilisieren und zu verbessern. © 2016 S. Karger GmbH, Freiburg.

A NEW INSAR DERIVED DEM OF BLACK RAPIDS GLACIER

NASA Astrophysics Data System (ADS)

Shugar, D. H.; Rabus, B.; Clague, J. J.

2009-12-01

We have constructed a new digital elevation model representing the 1995 surface of surge-type Black Rapids Glacier and the surrounding central Alaska Range, using ERS-1/2 repeat-pass interferometry. First, we isolated the topographic phase from three interferograms with contrasting perpendicular baselines. Next we attempted to automatically unwrap this topographic phase but encountered numerous errors due to the terrain containing areas of poor coherence from fringe aliasing, radar layover or shadow. We then consistently corrected these persistent phase-unwrapping errors in all three interferograms using an iterative semi-automated approach that capitalizes on the multi-baseline nature of the data set. Over the surface of Black Rapids Glacier, the accuracy of the new DEM is estimated at better than +/- 12 m. Ground-surveyed spot elevations from 1995 corroborate this accuracy estimate. Comparison of the new DEM with a 1951 U.S. Geological Survey topographic map, and with ground survey data from other years, shows the gradual return of Black Rapids Glacier to pre-surge conditions. In the 44-year period between 1951 and 1995 the observed average steepening of the longitudinal profile is ~0.6°. The maximum elevation changes in the ablation and accumulation zones are -256 m and +75 m, respectively, suggesting corresponding average rates of elevation change of about -5.8 m/yr and +1.7 m/yr. These rates are 1.5-2 times higher than those indicated by the ground survey spot elevation measurements over the period 1975 to 2005. Considering the significant overlap of the two periods of measurement, the inferred average rates for 1951-1975 would have to be very large (-7.5 m/yr and +2.3 m/yr, respectively) for these two findings to be consistent. A second comparison with the recently released ASTER G-DEM (data from 2001) led to no glaciologically usable results due to major artifacts in the ASTER G-DEM. We therefore conclude that the 1951 U.S. Geological Survey map and the

Supply Chain Management (SCM) mit Kanban

NASA Astrophysics Data System (ADS)

Beer, Anja; Dickmann, Eva; Dickmann, Philipp; Gerth, Wolf-Michael; Graßy, Mario; Herron, Colin; Schmidt, Peter; Seidl, Florian; Wittmann, Claus-Eduard

Nach Schätzungen von Mercer Management Consulting und dem Fraunhofer Institut wird der Wertschöpfungsanteil in der Automobilindustrie von durchschnittlich 35 % im Jahr 2002 auf 23 % im Jahr 2015 sinken [Merc 04]. Der Trend, die Produktionstiefe oder allgemeiner, die Wertschöpfungstiefe, zu reduzieren, hat zur Folge, dass die Kaufteile den größeren Teil der Wertschöpfung einnehmen. Die Optimierungspotentiale und der Einfluss auf die Kosten wandern immer mehr zu den Lieferanten, vor allem bei größeren Unternehmen oder Konzernen. Lieferanten-Philosophien, die auf oberflächlichen Verbindungen zu Lieferanten aufbauen, um immer optimal und schnell den günstigsten Teilepreis zu erhalten, haben sich in vielen Sparten oder Produktbereichen, z. B. im Maschinenbau, im besten Fall als kurzfristig erfolgreich erwiesen. Kooperative und nachhaltige Strategien sind der erfolgversprechendere Weg, zumindest mittelbis langfristig. In der Realität wird sehr wenig in Supply Chain-Konzepte investiert und die Umsetzungen sind daher vielmals oberflächlich.

Announcing the Availability of the MIT SMASS and SMASSIR Data Sets

NASA Technical Reports Server (NTRS)

Binzel, R. P.; Bus, S. J.; Burbine, T. H.; Rivkin, A. S.

2001-01-01

We announce the release of visible and near-infrared reflectance spectroscopy measurements for nearly 2000 asteroids obtained by the MIT Small Main-Belt Asteroid Spectroscopic Survey (SMASS) program. Data are being released via http://smass.mit.edu. Additional information is contained in the original extended abstract.

Identification and delineation of areas flood hazard using high accuracy of DEM data

NASA Astrophysics Data System (ADS)

Riadi, B.; Barus, B.; Widiatmaka; Yanuar, M. J. P.; Pramudya, B.

2018-05-01

Flood incidents that often occur in Karawang regency need to be mitigated. These expectations exist on technologies that can predict, anticipate and reduce disaster risks. Flood modeling techniques using Digital Elevation Model (DEM) data can be applied in mitigation activities. High accuracy DEM data used in modeling, will result in better flooding flood models. The result of high accuracy DEM data processing will yield information about surface morphology which can be used to identify indication of flood hazard area. The purpose of this study was to identify and describe flood hazard areas by identifying wetland areas using DEM data and Landsat-8 images. TerraSAR-X high-resolution data is used to detect wetlands from landscapes, while land cover is identified by Landsat image data. The Topography Wetness Index (TWI) method is used to detect and identify wetland areas with basic DEM data, while for land cover analysis using Tasseled Cap Transformation (TCT) method. The result of TWI modeling yields information about potential land of flood. Overlay TWI map with land cover map that produces information that in Karawang regency the most vulnerable areas occur flooding in rice fields. The spatial accuracy of the flood hazard area in this study was 87%.

How large is the Upper Indus Basin? The pitfalls of auto-delineation using DEMs

NASA Astrophysics Data System (ADS)

Khan, Asif; Richards, Keith S.; Parker, Geoffrey T.; McRobie, Allan; Mukhopadhyay, Biswajit

2014-02-01

Extraction of watershed areas from Digital Elevation Models (DEMs) is increasingly required in a variety of environmental analyses. It is facilitated by the availability of DEMs based on remotely sensed data, and by Geographical Information System (GIS) software. However, accurate delineation depends on the quality of the DEM and the methodology adopted. This paper considers automated and supervised delineation in a case study of the Upper Indus Basin (UIB), Pakistan, for which published estimates of the basin area show significant disagreement, ranging from 166,000 to 266,000 km2. Automated delineation used ArcGIS Archydro and hydrology tools applied to three good quality DEMs (two from SRTM data with 90m resolution, and one from 30m resolution ASTER data). Automatic delineation defined a basin area of c.440,000 km2 for the UIB, but included a large area of internal drainage in the western Tibetan Plateau. It is shown that discrepancies between different estimates reflect differences in the initial extent of the DEM used for watershed delineation, and the unchecked effect of iterative pit-filling of the DEM (going beyond the filling of erroneous pixels to filling entire closed basins). For the UIB we have identified critical points where spurious addition of catchment area has arisen, and use Google Earth to examine the geomorphology adjacent to these points, and also examine the basin boundary data provided by the HydroSHEDS database. We show that the Pangong Tso watershed and some other areas in the western Tibetan plateau are not part of the UIB, but are areas of internal drainage. Our best estimate of the area of the Upper Indus Basin (at Besham Qila) is 164,867 km2 based on the SRTM DEM, and 164,853 km2 using the ASTER DEM). This matches the catchment area measured by WAPDA SWHP. An important lesson from this investigation is that one should not rely on automated delineation, as iterative pit-filling can produce spurious drainage networks and basins, when

MIT - Massachusetts Institute of Technology

Science.gov Websites

energy cancer diversity global industry public service Solve The MIT Campaign for a Better World give to produce electricity Drug-carrying nanoparticles could help fight brain cancer Drug-carrying nanoparticles could help fight brain cancer New dispatching approach optimizes a city's taxi fleet New dispatching

Developmental Eye Movement (DEM) Test Norms for Mandarin Chinese-Speaking Chinese Children.

PubMed

Xie, Yachun; Shi, Chunmei; Tong, Meiling; Zhang, Min; Li, Tingting; Xu, Yaqin; Guo, Xirong; Hong, Qin; Chi, Xia

2016-01-01

The Developmental Eye Movement (DEM) test is commonly used as a clinical visual-verbal ocular motor assessment tool to screen and diagnose reading problems at the onset. No established norm exists for using the DEM test with Mandarin Chinese-speaking Chinese children. This study aims to establish the normative values of the DEM test for the Mandarin Chinese-speaking population in China; it also aims to compare the values with three other published norms for English-, Spanish-, and Cantonese-speaking Chinese children. A random stratified sampling method was used to recruit children from eight kindergartens and eight primary schools in the main urban and suburban areas of Nanjing. A total of 1,425 Mandarin Chinese-speaking children aged 5 to 12 years took the DEM test in Mandarin Chinese. A digital recorder was used to record the process. All of the subjects completed a symptomatology survey, and their DEM scores were determined by a trained tester. The scores were computed using the formula in the DEM manual, except that the "vertical scores" were adjusted by taking the vertical errors into consideration. The results were compared with the three other published norms. In our subjects, a general decrease with age was observed for the four eye movement indexes: vertical score, adjusted horizontal score, ratio, and total error. For both the vertical and adjusted horizontal scores, the Mandarin Chinese-speaking children completed the tests much more quickly than the norms for English- and Spanish-speaking children. However, the same group completed the test slightly more slowly than the norms for Cantonese-speaking children. The differences in the means were significant (P<0.001) in all age groups. For several ages, the scores obtained in this study were significantly different from the reported scores of Cantonese-speaking Chinese children (P<0.005). Compared with English-speaking children, only the vertical score of the 6-year-old group, the vertical-horizontal time

Developmental Eye Movement (DEM) Test Norms for Mandarin Chinese-Speaking Chinese Children

PubMed Central

Tong, Meiling; Zhang, Min; Li, Tingting; Xu, Yaqin; Guo, Xirong; Hong, Qin; Chi, Xia

2016-01-01

The Developmental Eye Movement (DEM) test is commonly used as a clinical visual-verbal ocular motor assessment tool to screen and diagnose reading problems at the onset. No established norm exists for using the DEM test with Mandarin Chinese-speaking Chinese children. This study aims to establish the normative values of the DEM test for the Mandarin Chinese-speaking population in China; it also aims to compare the values with three other published norms for English-, Spanish-, and Cantonese-speaking Chinese children. A random stratified sampling method was used to recruit children from eight kindergartens and eight primary schools in the main urban and suburban areas of Nanjing. A total of 1,425 Mandarin Chinese-speaking children aged 5 to 12 years took the DEM test in Mandarin Chinese. A digital recorder was used to record the process. All of the subjects completed a symptomatology survey, and their DEM scores were determined by a trained tester. The scores were computed using the formula in the DEM manual, except that the “vertical scores” were adjusted by taking the vertical errors into consideration. The results were compared with the three other published norms. In our subjects, a general decrease with age was observed for the four eye movement indexes: vertical score, adjusted horizontal score, ratio, and total error. For both the vertical and adjusted horizontal scores, the Mandarin Chinese-speaking children completed the tests much more quickly than the norms for English- and Spanish-speaking children. However, the same group completed the test slightly more slowly than the norms for Cantonese-speaking children. The differences in the means were significant (P<0.001) in all age groups. For several ages, the scores obtained in this study were significantly different from the reported scores of Cantonese-speaking Chinese children (P<0.005). Compared with English-speaking children, only the vertical score of the 6-year-old group, the vertical

An Interferometric Processing Method to Maintain both Accuracy and Resolution of dem Using GAOFEN-3 SAR Data

NASA Astrophysics Data System (ADS)

Li, T.; Tang, X.; Gao, X.; Chen, Q.; Zhang, X.; Guo, L.

2018-04-01

Gaofen-3 (GF-3) is the only in-orbit SAR satellite of China civilian fields. It is designed especially for ocean observation but not for interferometric applications. However, during the past one and a half years, the orbits of the satellite were adjusted for several times to ensure that the perpendicular baseline is short enough to provide interferograms. In this paper, we used the multi-look iteration algorithm to analyze the DEM obtained from InSAR. We first provide the theory of the method by considering the relationship between multi-look factor and the interferometric phase gradient. Then the GF-3 data as well as TanDEM-X data covering Songshan Mountain are taken for experiments. We use both the GCP data as well as the SRTM DEM for reference. The root-mean-square (RMS) values of TanDEM-X DEM assessed using GCP are 9.4 m, 9.3 m and 8.3 m with reference to ML factors of 8 × 8, 4 × 4 and 2 × 2, respectively. If we assess using SRTM, the corresponding RMS are 1.7 m, 5.4 m and 5.4 m. The result is opposite to that obtained using GCP given that the grid size of SRTM DEM is 90 m. The larger the ML factor, the more similar the calculated DEM to SRTM. RMS of GF-3 DEM compared to GCP is 10.2 m, 13.0 m and 13.8 m with reference to ML factors of 8 × 8, 4 × 4 and 2 × 2, respectively. While that compared to SRTM is 4.6 m, 15.1 m and 23.7 m. The accuracy is low compared to TanDEM-X DEM. Results show that the GF-3 data is potential in providing DEM data. However, the operational applications using GF-3 as interferometric data source would be challenging because of the instability of baseline coherence as well as the temporal coherence.

Trizentrische Analyse von Kofaktoren und Komorbidität des Pyoderma gangraenosum.

PubMed

Jockenhöfer, Finja; Herberger, Katharina; Schaller, Jörg; Hohaus, Katja Christina; Stoffels-Weindorf, Maren; Ghazal, Philipp Al; Augustin, Matthias; Dissemond, Joachim

2016-10-01

Das Pyoderma gangraenosum (PG) ist eine seltene, inflammatorische destruktiv-ulzerierende neutrophile Erkrankung mit weitgehend unklarer Pathophysiologie. In dieser Studie wurden die potenziell relevanten Kofaktoren und Begleiterkrankungen von Patienten mit PG aus drei dermatologischen Wundzentren in Deutschland differenziert ausgewertet. Von den insgesamt 121 analysierten Patienten waren Frauen (66,9 %) häufiger betroffen als Männer. Das Alter der Patienten war 18-96 Jahre (Mittelwert [MW]: 59,8); die Wunden hatten eine Größe von 1-600 cm² (MW: 65,6 cm²) und waren überwiegend sehr schmerzhaft (VAS 1-10, MW: 7). Die Unterschenkel waren am häufigsten (71,9 %) betroffen. Bei 12 (9,9 %) Patienten bestanden chronisch entzündliche Darmerkrankungen (5,8 % Colitis ulcerosa; 4,1 % Morbus Crohn), bei 14,1 % der Patienten wurde eine Begleiterkrankung aus dem rheumatischen Formenkreis beschrieben. Neoplasien bestanden bei 20,6 % der Patienten, von denen 6,6 % als hämatologische und 14,1 % als solide Neoplasien klassifiziert wurden. Aus dem Kreis des metabolischen Syndroms wurde bei 69,4 % Patienten eine Adipositas, bei 57,9 % eine arterielle Hypertonie und bei 33,9 % ein Diabetes mellitus diagnostiziert. Diese Datenanalyse bestätigt Assoziationen des PG mit dem metabolischen Syndrom und mit Neoplasien, die zukünftig frühzeitig bei einer zielgerichteten Diagnostik der Patienten beachtet und behandelt werden sollten. © 2016 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

MIT January Operational Internship Experience

NASA Technical Reports Server (NTRS)

Bosanac, Natasha; DeVivero, Charlie; James, Jillian; Perez-Martinez, Carla; Pino, Wendy; Wang, Andrew; Willett, Ezekiel; Williams, Kwami

2010-01-01

This viewgraph presentation describes the MIT January Operational Internship Experience (JOIE) program. The topics include: 1) Landing and Recovery; 2) Transportation; 3) Shuttle Processing; 4) Constellation Processing; 5) External Tank; 6) Launch Pad; 7) Ground Operations; 8) Hypergolic Propellants; 9) Environmental; 10) Logistics; 11) Six Sigma; 12) Systems Engineering; and 13) Human Factors.

Combined DEM Extration Method from StereoSAR and InSAR

NASA Astrophysics Data System (ADS)

Zhao, Z.; Zhang, J. X.; Duan, M. Y.; Huang, G. M.; Yang, S. C.

2015-06-01

A pair of SAR images acquired from different positions can be used to generate digital elevation model (DEM). Two techniques exploiting this characteristic have been introduced: stereo SAR and interferometric SAR. They permit to recover the third dimension (topography) and, at the same time, to identify the absolute position (geolocation) of pixels included in the imaged area, thus allowing the generation of DEMs. In this paper, StereoSAR and InSAR combined adjustment model are constructed, and unify DEM extraction from InSAR and StereoSAR into the same coordinate system, and then improve three dimensional positioning accuracy of the target. We assume that there are four images 1, 2, 3 and 4. One pair of SAR images 1,2 meet the required conditions for InSAR technology, while the other pair of SAR images 3,4 can form stereo image pairs. The phase model is based on InSAR rigorous imaging geometric model. The master image 1 and the slave image 2 will be used in InSAR processing, but the slave image 2 is only used in the course of establishment, and the pixels of the slave image 2 are relevant to the corresponding pixels of the master image 1 through image coregistration coefficient, and it calculates the corresponding phase. It doesn't require the slave image in the construction of the phase model. In Range-Doppler (RD) model, the range equation and Doppler equation are a function of target geolocation, while in the phase equation, the phase is also a function of target geolocation. We exploit combined adjustment model to deviation of target geolocation, thus the problem of target solution is changed to solve three unkonwns through seven equations. The model was tested for DEM extraction under spaceborne InSAR and StereoSAR data and compared with InSAR and StereoSAR methods respectively. The results showed that the model delivered a better performance on experimental imagery and can be used for DEM extraction applications.

Mobile-IT Education (MIT.EDU): M-Learning Applications for Classroom Settings

ERIC Educational Resources Information Center

Sung, M.; Gips, J.; Eagle, N.; Madan, A.; Caneel, R.; DeVaul, R.; Bonsen, J.; Pentland, A.

2005-01-01

In this paper, we describe the Mobile-IT Education (MIT.EDU) system, which demonstrates the potential of using a distributed mobile device architecture for rapid prototyping of wireless mobile multi-user applications for use in classroom settings. MIT.EDU is a stable, accessible system that combines inexpensive, commodity hardware, a flexible…

The sensitivity of catchment hypsometry and hypsometric properties to DEM resolution and polynomial order

NASA Astrophysics Data System (ADS)

Liffner, Joel W.; Hewa, Guna A.; Peel, Murray C.

2018-05-01

Derivation of the hypsometric curve of a catchment, and properties relating to that curve, requires both use of topographical data (commonly in the form of a Digital Elevation Model - DEM), and the estimation of a functional representation of that curve. An early investigation into catchment hypsometry concluded 3rd order polynomials sufficiently describe the hypsometric curve, without the consideration of higher order polynomials, or the sensitivity of hypsometric properties relating to the curve. Another study concluded the hypsometric integral (HI) is robust against changes in DEM resolution, a conclusion drawn from a very limited sample size. Conclusions from these earlier studies have resulted in the adoption of methods deemed to be "sufficient" in subsequent studies, in addition to assumptions that the robustness of the HI extends to other hypsometric properties. This study investigates and demonstrates the sensitivity of hypsometric properties to DEM resolution, DEM type and polynomial order through assessing differences in hypsometric properties derived from 417 catchments and sub-catchments within South Australia. The sensitivity of hypsometric properties across DEM types and polynomial orders is found to be significant, which suggests careful consideration of the methods chosen to derive catchment hypsometric information is required.

Elevation-Based Sea-Level Rise Vulnerability Assessment of Mindanao, Philippines: are Freely-Available 30-M Dems Good Enough?

NASA Astrophysics Data System (ADS)

Santillan, J. R.; Makinano-Santillan, M.

2017-09-01

We assessed the vertical accuracies and uncertainties of three freely-available global DEMs as inputs to elevation-based sea-level rise vulnerability assessment of Mindanao, Philippines - an area where above average SLR of 14.7 mm/year was recently found. These DEMs are the Shuttle Radar Topography Mission (SRTM) DEM, ASTER Global DEM (GDEM Version 2), and ALOS World 3D-30 (AW3D30). Using 2,076 ground control points, we computed each DEM's vertical accuracies and uncertainties, and from these we determined the smallest increment of sea-level rise (SLRImin) that should be considered when using the DEMs for SLR impact assessment, as well as the Minimum Planning Timeline (TLmin) for an elevation-based SLR assessment. Results of vertical accuracy assessment revealed Root Mean Square Errors of 9.80 m for ASTER GDEM V2, 5.16 m for SRTM DEM, and 4.32 m for AW3D30. Vertical uncertainties in terms of the Linear Error at 95 % Confidence (LE95) were found to be as follows: 19.21 m for ASTER GDEM V2, 10.12 m for SRTM DEM, and 8.47 m for AW3D30. From these, we found that ASTER GDEM2 is suitable to model SLR increments of at least 38.41 m and it will take 2,613 years for the cumulative water level increase of 14.7 mm/year to reach the minimum SLR increment afforded by this DEM. For the SRTM DEM, SLRImin and TLmin were computed as 20.24 m and 1,377 years, respectively. For the AW3D30, SLRImin and TLmin were computed as 16.92 m and 1,151 years, respectively. These results suggest that the readily available global DEMs' suitability for mapping coastal inundations due to SLR in our study area is limited by their low vertical accuracies and high uncertainties. All the three DEMs do not have the necessary accuracy and minimum uncertainties that will make them suitable for mapping inundations of Mindanao at smaller increments of SLR (e.g., SLR ≤ 5 m). Hence, users who apply any of these DEMs

Structural basis for midbody targeting of spastin by the ESCRT-III protein CHMP1B

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Dong; Rimanchi, Neggy; Renvoise, Benoit

2009-01-15

The endosomal sorting complex required for transport (ESCRT) machinery, including ESCRT-III, localizes to the midbody and participates in the membrane-abscission step of cytokinesis. The ESCRT-III protein charged multivesicular body protein 1B (CHMP1B) is required for recruitment of the MIT domain-containing protein spastin, a microtubule-severing enzyme, to the midbody. The 2.5-{angstrom} structure of the C-terminal tail of CHMP1B with the MIT domain of spastin reveals a specific, high-affinity complex involving a noncanonical binding site between the first and third helices of the MIT domain. The structural interface is twice as large as that of the MIT domain of the VPS4-CHMP complex,more » consistent with the high affinity of the interaction. A series of unique hydrogen-bonding interactions and close packing of small side chains discriminate against the other ten human ESCRT-III subunits. Point mutants in the CHMP1B binding site of spastin block recruitment of spastin to the midbody and impair cytokinesis.« less

MIT ASTROMAG 1.7 meter disk magnet design report

NASA Technical Reports Server (NTRS)

Marston, P. G.; Hale, J. R.; Vieira, R.; Zhukovsky, A.; Titus, P. H.; Sullivan, J. D.; Dawson, A. M.

1990-01-01

MIT has proposed a magnet design for ASTROMAG, which has demonstrated substantial improvement in performance as compared with the present HEAO baseline design. Several advantages of the MIT disk design are listed along with design characteristics. Details of field contours and active field regions are shown along with comparisons with other designs. Three alternative design configurations for the ASTROMAG disk coils are summarized. The parameters of the conductors are listed and basic parameters for each of the complete systems are shown.

DemQSAR: predicting human volume of distribution and clearance of drugs

NASA Astrophysics Data System (ADS)

Demir-Kavuk, Ozgur; Bentzien, Jörg; Muegge, Ingo; Knapp, Ernst-Walter

2011-12-01

In silico methods characterizing molecular compounds with respect to pharmacologically relevant properties can accelerate the identification of new drugs and reduce their development costs. Quantitative structure-activity/-property relationship (QSAR/QSPR) correlate structure and physico-chemical properties of molecular compounds with a specific functional activity/property under study. Typically a large number of molecular features are generated for the compounds. In many cases the number of generated features exceeds the number of molecular compounds with known property values that are available for learning. Machine learning methods tend to overfit the training data in such situations, i.e. the method adjusts to very specific features of the training data, which are not characteristic for the considered property. This problem can be alleviated by diminishing the influence of unimportant, redundant or even misleading features. A better strategy is to eliminate such features completely. Ideally, a molecular property can be described by a small number of features that are chemically interpretable. The purpose of the present contribution is to provide a predictive modeling approach, which combines feature generation, feature selection, model building and control of overtraining into a single application called DemQSAR. DemQSAR is used to predict human volume of distribution (VDss) and human clearance (CL). To control overtraining, quadratic and linear regularization terms were employed. A recursive feature selection approach is used to reduce the number of descriptors. The prediction performance is as good as the best predictions reported in the recent literature. The example presented here demonstrates that DemQSAR can generate a model that uses very few features while maintaining high predictive power. A standalone DemQSAR Java application for model building of any user defined property as well as a web interface for the prediction of human VDss and CL is

DemQSAR: predicting human volume of distribution and clearance of drugs.

PubMed

Demir-Kavuk, Ozgur; Bentzien, Jörg; Muegge, Ingo; Knapp, Ernst-Walter

2011-12-01

In silico methods characterizing molecular compounds with respect to pharmacologically relevant properties can accelerate the identification of new drugs and reduce their development costs. Quantitative structure-activity/-property relationship (QSAR/QSPR) correlate structure and physico-chemical properties of molecular compounds with a specific functional activity/property under study. Typically a large number of molecular features are generated for the compounds. In many cases the number of generated features exceeds the number of molecular compounds with known property values that are available for learning. Machine learning methods tend to overfit the training data in such situations, i.e. the method adjusts to very specific features of the training data, which are not characteristic for the considered property. This problem can be alleviated by diminishing the influence of unimportant, redundant or even misleading features. A better strategy is to eliminate such features completely. Ideally, a molecular property can be described by a small number of features that are chemically interpretable. The purpose of the present contribution is to provide a predictive modeling approach, which combines feature generation, feature selection, model building and control of overtraining into a single application called DemQSAR. DemQSAR is used to predict human volume of distribution (VD(ss)) and human clearance (CL). To control overtraining, quadratic and linear regularization terms were employed. A recursive feature selection approach is used to reduce the number of descriptors. The prediction performance is as good as the best predictions reported in the recent literature. The example presented here demonstrates that DemQSAR can generate a model that uses very few features while maintaining high predictive power. A standalone DemQSAR Java application for model building of any user defined property as well as a web interface for the prediction of human VD(ss) and CL is

Biotechnology Process Engineering Center at MIT Home

Science.gov Websites

BPEC Definition 77 Massachusetts Avenue, Building 16 Room 429, Cambridge, MA 02139 Telephone (617 Leadership Council Facilities | Umbrella Programs | Events | News | Links | MIT | National Science Foundation

DEM interpolation weight calculation modulus based on maximum entropy

NASA Astrophysics Data System (ADS)

Chen, Tian-wei; Yang, Xia

2015-12-01

There is negative-weight in traditional interpolation of gridding DEM, in the article, the principle of Maximum Entropy is utilized to analyze the model system which depends on modulus of space weight. Negative-weight problem of the DEM interpolation is researched via building Maximum Entropy model, and adding nonnegative, first and second order's Moment constraints, the negative-weight problem is solved. The correctness and accuracy of the method was validated with genetic algorithm in matlab program. The method is compared with the method of Yang Chizhong interpolation and quadratic program. Comparison shows that the volume and scaling of Maximum Entropy's weight is fit to relations of space and the accuracy is superior to the latter two.

A new morphology algorithm for shoreline extraction from DEM data

NASA Astrophysics Data System (ADS)

Yousef, Amr H.; Iftekharuddin, Khan; Karim, Mohammad

2013-03-01

Digital elevation models (DEMs) are a digital representation of elevations at regularly spaced points. They provide an accurate tool to extract the shoreline profiles. One of the emerging sources of creating them is light detection and ranging (LiDAR) that can capture a highly dense cloud points with high resolution that can reach 15 cm and 100 cm in the vertical and horizontal directions respectively in short periods of time. In this paper we present a multi-step morphological algorithm to extract shorelines locations from the DEM data and a predefined tidal datum. Unlike similar approaches, it utilizes Lowess nonparametric regression to estimate the missing values within the DEM file. Also, it will detect and eliminate the outliers and errors that result from waves, ships, etc by means of anomality test with neighborhood constrains. Because, there might be some significant broken regions such as branches and islands, it utilizes a constrained morphological open and close to reduce these artifacts that can affect the extracted shorelines. In addition, it eliminates docks, bridges and fishing piers along the extracted shorelines by means of Hough transform. Based on a specific tidal datum, the algorithm will segment the DEM data into water and land objects. Without sacrificing the accuracy and the spatial details of the extracted boundaries, the algorithm should smooth and extract the shoreline profiles by tracing the boundary pixels between the land and the water segments. For given tidal values, we qualitatively assess the visual quality of the extracted shorelines by superimposing them on the available aerial photographs.

GPS-Based Precision Baseline Reconstruction for the TanDEM-X SAR-Formation

NASA Technical Reports Server (NTRS)

Montenbruck, O.; vanBarneveld, P. W. L.; Yoon, Y.; Visser, P. N. A. M.

2007-01-01

The TanDEM-X formation employs two separate spacecraft to collect interferometric Synthetic Aperture Radar (SAR) measurements over baselines of about 1 km. These will allow the generation ofa global Digital Elevation Model (DEM) with an relative vertical accuracy of 2-4 m and a 10 m ground resolution. As part of the ground processing, the separation of the SAR antennas at the time of each data take must be reconstructed with a 1 mm accuracy using measurements from two geodetic grade GPS receivers. The paper discusses the TanDEM-X mission as well as the methods employed for determining the interferometric baseline with utmost precision. Measurements collected during the close fly-by of the two GRACE satellites serve as a reference case to illustrate the processing concept, expected accuracy and quality control strategies.

Education Outreach at M.I.T. Plasma Science and Fusion Center

NASA Astrophysics Data System (ADS)

Rivenberg, P.; Censabella, V.

2000-10-01

At the MIT PSFC student and staff volunteers work together to increase the public's knowledge of fusion and plasma-related experiments. Seeking to generate excitement about science, engineering and mathematics, the PSFC holds a number of outreach activities throughout the year, including Middle and High School Outreach Days and the Mr. Magnet program. During the past year, in collaboration with the MIT Museum, the PSFC reprogrammed their C-Mod, Jr Video Game to be operated via the keyboard instead of joysticks. The game will eventually be available on the web and on disc. The PSFC maintains a Home Page on the World Wide Web, which can be reached at http://www.psfc.mit.edu.

DEM analysis of FOXSI-2 microflare using AIA observations

NASA Astrophysics Data System (ADS)

Athiray Panchapakesan, Subramania; Glesener, Lindsay; Vievering, Juliana; Camilo Buitrago-Casas, Juan; Christe, Steven; Inglis, Andrew; Krucker, Sam; Musset, Sophie

2017-08-01

The second flight of Focusing Optics X-ray Solar Imager (FOXSI) sounding rocket experiment was successfully completed on 11 December 2014. FOXSI makes direct imaging and spectral observation of the Sun in hard X-rays using grazing incidence optics modules which focus X-rays onto seven focal plane detectors kept at a 2m distance, in the energy range 4 to 20 keV, to study particle acceleration and coronal heating. Significant HXR emissions were observed by FOXSI during microflare events with A0.5 and A2.5 class, as classified by GOES, that occurred during FOXSI-2 flight.Spectral analysis of FOXSI data for these events indicate presence of plasma at higher temperatures (>10MK). We attempt to study the plasma content in the corona at different temperatures, characterized by the differential emission measure (DEM), over the FOXSI-2 observed flare regions using the Atmospheric Imaging Assembly (SDO/AIA) data. We utilize AIA observations in different EUV filters that are sensitive to ionized iron lines, to determine the DEM by using a regularized inversion method. This poster will show the properties of hot plasma as derived from FOXSI-2 HXR spectra with supporting DEM analysis using AIA observations.

Long-lived mitochondrial (Mit) mutants of Caenorhabditis elegans utilize a novel metabolism.

PubMed

Butler, Jeffrey A; Ventura, Natascia; Johnson, Thomas E; Rea, Shane L

2010-12-01

The Caenorhabditis elegans mitochondrial (Mit) mutants have disrupted mitochondrial electron transport chain (ETC) functionality, yet, surprisingly, they are long lived. We have previously proposed that Mit mutants supplement their energy needs by exploiting alternate energy production pathways normally used by wild-type animals only when exposed to hypoxic conditions. We have also proposed that longevity in the Mit mutants arises as a property of their new metabolic state. If longevity does arise as a function of metabolic state, we would expect to find a common metabolic signature among these animals. To test these predictions, we established a novel approach monitoring the C. elegans exometabolism as a surrogate marker for internal metabolic events. Using HPLC-ultraviolet-based metabolomics and multivariate analyses, we show that long-lived clk-1(qm30) and isp-1(qm150) Mit mutants have a common metabolic profile that is distinct from that of aerobically cultured wild-type animals and, unexpectedly, wild-type animals cultured under severe oxygen deprivation. Moreover, we show that 2 short-lived mitochondrial ETC mutants, mev-1(kn1) and ucr-2.3(pk732), also share a common metabolic signature that is unique. We show that removal of soluble fumarate reductase unexpectedly increases health span in several genetically defined Mit mutants, identifying at least 1 alternate energy production pathway, malate dismutation, that is operative in these animals. Our study suggests long-lived, genetically specified Mit mutants employ a novel metabolism and that life span may well arise as a function of metabolic state.

A framework for global terrain classification using 250-m DEMs to predict geohazards

NASA Astrophysics Data System (ADS)

Iwahashi, J.; Matsuoka, M.; Yong, A.

2016-12-01

Geomorphology is key for identifying factors that control geohazards induced by landslides, liquefaction, and ground shaking. To systematically identify landforms that affect these hazards, Iwahashi and Pike (2007; IP07) introduced an automated terrain classification scheme using 1-km-scale Shuttle Radar Topography Mission (SRTM) digital elevation models (DEMs). The IP07 classes describe 16 categories of terrain types and were used as a proxy for predicting ground motion amplification (Yong et al., 2012; Seyhan et al., 2014; Stewart et al., 2014; Yong, 2016). These classes, however, were not sufficiently resolved because coarse-scaled SRTM DEMs were the basis for the categories (Yong, 2016). Thus, we develop a new framework consisting of more detailed polygonal global terrain classes to improve estimations of soil-type and material stiffness. We first prepare high resolution 250-m DEMs derived from the 2010 Global Multi-resolution Terrain Elevation Data (GMTED2010). As in IP07, we calculate three geometric signatures (slope, local convexity and surface texture) from the DEMs. We create additional polygons by using the same signatures and multi-resolution segmentation techniques on the GMTED2010. We consider two types of surface texture thresholds in different window sizes (3x3 and 13x13 pixels), in addition to slope and local convexity, to classify pixels within the DEM. Finally, we apply the k-means clustering and thresholding methods to the 250-m DEM and produce more detailed polygonal terrain classes. We compare the new terrain classification maps of Japan and California with geologic, aerial photography, and landslide distribution maps, and visually find good correspondence of key features. To predict ground motion amplification, we apply the Yong (2016) method for estimating VS30. The systematic classification of geomorphology has the potential to provide a better understanding of the susceptibility to geohazards, which is especially vital in populated areas.

Generation of a precise DEM by interactive synthesis of multi-temporal elevation datasets: a case study of Schirmacher Oasis, East Antarctica

NASA Astrophysics Data System (ADS)

Jawak, Shridhar D.; Luis, Alvarinho J.

2016-05-01

Digital elevation model (DEM) is indispensable for analysis such as topographic feature extraction, ice sheet melting, slope stability analysis, landscape analysis and so on. Such analysis requires a highly accurate DEM. Available DEMs of Antarctic region compiled by using radar altimetry and the Antarctic digital database indicate elevation variations of up to hundreds of meters, which necessitates the generation of local improved DEM. An improved DEM of the Schirmacher Oasis, East Antarctica has been generated by synergistically fusing satellite-derived laser altimetry data from Geoscience Laser Altimetry System (GLAS), Radarsat Antarctic Mapping Project (RAMP) elevation data and Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) global elevation data (GDEM). This is a characteristic attempt to generate a DEM of any part of Antarctica by fusing multiple elevation datasets, which is essential to model the ice elevation change and address the ice mass balance. We analyzed a suite of interpolation techniques for constructing a DEM from GLAS, RAMP and ASTER DEM-based point elevation datasets, in order to determine the level of confidence with which the interpolation techniques can generate a better interpolated continuous surface, and eventually improve the elevation accuracy of DEM from synergistically fused RAMP, GLAS and ASTER point elevation datasets. The DEM presented in this work has a vertical accuracy (≈ 23 m) better than RAMP DEM (≈ 57 m) and ASTER DEM (≈ 64 m) individually. The RAMP DEM and ASTER DEM elevations were corrected using differential GPS elevations as ground reference data, and the accuracy obtained after fusing multitemporal datasets is found to be improved than that of existing DEMs constructed by using RAMP or ASTER alone. This is our second attempt of fusing multitemporal, multisensory and multisource elevation data to generate a DEM of Antarctica, in order to address the ice elevation change and address the ice mass

The developmental eye movement (DEM) test and Cantonese-speaking children in Hong Kong SAR, China.

PubMed

Pang, Peter C; Lam, Carly S; Woo, George C

2010-07-01

There is no published norm for the Developmental Eye Movement (DEM) Test for Cantonese-speaking Chinese children. This study aimed to determine the normative values of this test for Cantonese-speaking Chinese children in Hong Kong SAR and to compare the results with the published norms of English-speaking and Spanish-speaking children. Cantonese-speaking students aged from 6 to 11 years were tested by the DEM test in Cantonese and a digital recorder was used to record the process. The DEM scores for the 305 students were determined by listening again to the audio records after the test and computed by using the formula from the DEM manual, except that the 'vertical scores' were adjusted by taking the vertical errors into consideration. The results were compared with other norms that have been published. Our subjects made more vertical errors than in other normative studies and adjusted vertical scores were proposed. In both adjusted vertical and horizontal scores, the Cantonese-speaking children completed the tests much faster than the norms for English- and Spanish-speaking children, the differences of the means being significant (p < 0.0001) in all age groups. The DEM norms may be affected by differences in languages, cultures and education systems among different ethnicities. The norms of the DEM test are proposed for Cantonese-speaking children in Hong Kong SAR, China.

Spritzgießen

NASA Astrophysics Data System (ADS)

Bürkle, Erwin; Ammer, Daniel; Würtele, Martin

Kunststoffe zu spritzgießen ist eine der fortschrittlichsten Verarbeitungstechnologien. Durch Spritzgießen, ein Verfahren der Urformtechnik werden Formteile in der Regel mit komplexer Geometrie vollautomatisch hergestellt. Ausgehend vom Verfahrensablauf werden Thermoplaste, Duroplaste oder Kautschuk in einer Spritzgießmaschine aus dem Feststoffzustand heraus aufgeschmolzen, in einen formgebenden Hohlraum (Werkzeug) eingespritzt, dort verdichtet, abgekühlt oder zur Reaktion gebracht und dann als Formteil aus dem Werkzeug ausgeworfen. Etwa 60 % aller Kunststoffverarbeitungsmaschinen sind Spritzgießmaschinen (Abb. 26.1). Auf ihnen werden Formteile mit sehr niedrigen Massen im mg-Bereich bis hin zu großen Massen in zwei - z. T. sogar auch dreistelligen kg-Bereich hergestellt. Der Prozess des Spritzgießens nutzt in idealer Weise das besondere physikalische Verhalten der Kunststoffe. In einem verhältnismäßig einfachen Prozess werden durch Erwärmen des Kunststoffes und der nachfolgenden Formgebung im Schmelzezustand mit abschließender Abkühlung in einem formgebenden Werkzeug direkt gebrauchsfertige Formteile hergestellt [1, 31].

A Novel DEM Approach to Simulate Block Propagation on Forested Slopes

NASA Astrophysics Data System (ADS)

Toe, David; Bourrier, Franck; Dorren, Luuk; Berger, Frédéric

2018-03-01

In order to model rockfall on forested slopes, we developed a trajectory rockfall model based on the discrete element method (DEM). This model is able to take the complex mechanical processes at work during an impact into account (large deformations, complex contact conditions) and can explicitly simulate block/soil, block/tree contacts as well as contacts between neighbouring trees. In this paper, we describe the DEM model developed and we use it to assess the protective effect of different types of forest. In addition, we compared it with a more classical rockfall simulation model. The results highlight that forests can significantly reduce rockfall hazard and that the spatial structure of coppice forests has to be taken into account in rockfall simulations in order to avoid overestimating the protective role of these forest structures against rockfall hazard. In addition, the protective role of the forests is mainly influenced by the basal area. Finally, the advantages and limitations of the DEM model were compared with classical rockfall modelling approaches.

Designs of LiMIT as a Limiter in the EAST Tokamak

NASA Astrophysics Data System (ADS)

Szott, Matthew; Christenson, Michael; Kalathiparambil, Kishor; Ruzic, David

2016-10-01

Liquid metal plasma facing components (PFCs) provide a constantly refreshing, self-healing surface that can reduce erosion and thermal stress damage to prolong device lifetime, and additionally decrease edge recycling, reduce impurities, and enhance plasma performance. The Liquid Metal Infused Trench (LiMIT) system, developed at UIUC, has demonstrated thermoelectric magnetohydrodynamic (TEMHD) driven flow of liquid lithium through series of solid trenches. This TEMHD effect drives liquid lithium in fusion systems using the plasma heat flux and the toroidal magnetic field, and the surface tension of the liquid lithium maintains a fresh surface on top of the solid trenches. LiMIT has been successfully tested at UIUC as well as HT-7 and Magnum PSI at heat fluxes up to 3 MW/m2. The next step is demonstrating system viability in full-scale fusion-relevant conditions. In collaboration with a team in Hefei, design and testing has begun for a large scale LiMIT system that will act as a limiter in EAST. The designs improve upon previous versions of LiMIT tested at Illinois and incorporate lessons learned from earlier tests of liquid metal PFCs at EAST. Existing infrastructure is used to load and supply lithium to the system, and the LiMIT trenches will help maintain a smooth, fresh surface as well as aid in propelling the lithium out of direct plasma flux to improve heat transfer. Supported by DOE/ALPS DE-FG02-99ER54515.

An improved method to represent DEM uncertainty in glacial lake outburst flood propagation using stochastic simulations

NASA Astrophysics Data System (ADS)

Watson, Cameron S.; Carrivick, Jonathan; Quincey, Duncan

2015-10-01

Modelling glacial lake outburst floods (GLOFs) or 'jökulhlaups', necessarily involves the propagation of large and often stochastic uncertainties throughout the source to impact process chain. Since flood routing is primarily a function of underlying topography, communication of digital elevation model (DEM) uncertainty should accompany such modelling efforts. Here, a new stochastic first-pass assessment technique was evaluated against an existing GIS-based model and an existing 1D hydrodynamic model, using three DEMs with different spatial resolution. The analysis revealed the effect of DEM uncertainty and model choice on several flood parameters and on the prediction of socio-economic impacts. Our new model, which we call MC-LCP (Monte Carlo Least Cost Path) and which is distributed in the supplementary information, demonstrated enhanced 'stability' when compared to the two existing methods, and this 'stability' was independent of DEM choice. The MC-LCP model outputs an uncertainty continuum within its extent, from which relative socio-economic risk can be evaluated. In a comparison of all DEM and model combinations, the Shuttle Radar Topography Mission (SRTM) DEM exhibited fewer artefacts compared to those with the Advanced Spaceborne Thermal Emission and Reflection Radiometer Global Digital Elevation Model (ASTER GDEM), and were comparable to those with a finer resolution Advanced Land Observing Satellite Panchromatic Remote-sensing Instrument for Stereo Mapping (ALOS PRISM) derived DEM. Overall, we contend that the variability we find between flood routing model results suggests that consideration of DEM uncertainty and pre-processing methods is important when assessing flow routing and when evaluating potential socio-economic implications of a GLOF event. Incorporation of a stochastic variable provides an illustration of uncertainty that is important when modelling and communicating assessments of an inherently complex process.

Sensitivity of Particle Size in Discrete Element Method to Particle Gas Method (DEM_PGM) Coupling in Underbody Blast Simulations

DTIC Science & Technology

2016-06-12

Particle Size in Discrete Element Method to Particle Gas Method (DEM_PGM) Coupling in Underbody Blast Simulations Venkatesh Babu, Kumar Kulkarni, Sanjay...buried in soil viz., (1) coupled discrete element & particle gas methods (DEM-PGM) and (2) Arbitrary Lagrangian-Eulerian (ALE), are investigated. The...DEM_PGM and identify the limitations/strengths compared to the ALE method. Discrete Element Method (DEM) can model individual particle directly, and

DEM GPU studies of industrial scale particle simulations for granular flow civil engineering applications

NASA Astrophysics Data System (ADS)

Pizette, Patrick; Govender, Nicolin; Wilke, Daniel N.; Abriak, Nor-Edine

2017-06-01

The use of the Discrete Element Method (DEM) for industrial civil engineering industrial applications is currently limited due to the computational demands when large numbers of particles are considered. The graphics processing unit (GPU) with its highly parallelized hardware architecture shows potential to enable solution of civil engineering problems using discrete granular approaches. We demonstrate in this study the pratical utility of a validated GPU-enabled DEM modeling environment to simulate industrial scale granular problems. As illustration, the flow discharge of storage silos using 8 and 17 million particles is considered. DEM simulations have been performed to investigate the influence of particle size (equivalent size for the 20/40-mesh gravel) and induced shear stress for two hopper shapes. The preliminary results indicate that the shape of the hopper significantly influences the discharge rates for the same material. Specifically, this work shows that GPU-enabled DEM modeling environments can model industrial scale problems on a single portable computer within a day for 30 seconds of process time.

An investigation of Digital Elevation Model (DEM) structure influence on flood modelling

NASA Astrophysics Data System (ADS)

Sahid; Nurrohman, A. W.; Hadi, M. P.

2018-04-01

Flood is one of the natural calamities that cause huge losses and damages. Flood hazard zonation has been widely produced to face the impact of the disaster. DEM as the primary data to construct the earth surface has been developed from rough to fine resolution. Aster GDEM v.2 within 1arc spatial resolution has an ability to derived DEM and TIN data as bases river geometrics data. Maximum daily peak discharges used to calculate flood peak discharge. Furthermore, steady flow analysis has been used to produce flood inundation model based on four scenarios with return periods 5yr, 10yr, 50yr, and 100yr. The model results have been validated using UAV flood map in 2016 by means of pixel by pixel operation and the result shows that the vertical variance between grid DEM and TIN data about 0.3 m.

MIT Lincoln Laboratory 2010 Facts

DTIC Science & Technology

2010-03-01

currently valid OMB control number. 1. REPORT DATE 2010 2. REPORT TYPE 3. DATES COVERED 00-00-2010 to 00-00-2010 4. TITLE AND SUBTITLE MIT Lincoln...space control ; air and missile defense; communications and information technology; intelligence, surveillance, and reconnaissance systems...advanced electronics; tactical systems; homeland protection and biological/chemical defense; and air traffic control . Two of the Laboratory’s principal

Observations of glacier mass changes and their system inherent drivers over Western Himalaya (Himachal Pradesh, India) during 2000-2013 using TanDEM-X and SRTM-C DEMs

NASA Astrophysics Data System (ADS)

Vijay, Saurabh; Braun, Matthias

2016-04-01

The glaciers in Himachal Pradesh (HP), India (Western Himalaya) are a part of widely spread Hindu Kush-Karakoram-Himalaya mountain ranges. The glacier mass changes depend on system inherent (size, topography, aspect etc.) and climatic factors (precipitation, temperature etc.). The glaciers in this region are mostly debris-covered with supraglacial ponds. They are mostly land-terminating but few of them terminate at the lakes. The two different precipitation regimes namely, Indian summer monsoon and mid-latitude winter westerlies, influence the glaciers in the region. The continuous observations of such glacier changes using field experiments are often limited and repeat pass satellite data potentially fills this gap. Previous studies notified that the bench mark glacier, called Chhota Shigri Glacier, experienced a transition from mass gain (or equilibrium) to loss around 1999. This study aims to estimate the mass change of glaciers in HP at two different time scales. During 2000-2012, we subtract TanDEM-X DEMs of Feb, 2012 from the SRTM C/X band DEM of Feb, 2000. The published ice thickness change of Chhota Shigri Glacier from field observations is compared with ice thickness change derived from DEM differencing. This potentially estimates the bias in thickness change due to different radar frequencies (C band for SRTM, X band for TanDEM-X). For 2012-2013, we use repeat pass TanDEM-X DEMs which don't require any further bias correction. We perform hypsometry analysis (25 m elevation bin) of thickness change of ~800 km2 of ice covered area during these times scales. The analysis shows a transition of thickness change -2.0 myr-1 (4000-4200 m elevation) to -2.7 myr-1 at higher elevations (4200-4800) and further transits upstream. This clearly shows that the presence of thick debris at the glacier tongue act as insulator and reduce the downwasting. The downwasting increases as the surface consists of thin debris and exposed more to radiation. The downwasting linearly

Simulation of TanDEM-X interferograms for urban change detection

NASA Astrophysics Data System (ADS)

Welte, Amelie; Hammer, Horst; Thiele, Antje; Hinz, Stefan

2017-10-01

Damage detection after natural disasters is one of the remote sensing tasks in which Synthetic Aperture Radar (SAR) sensors play an important role. Since SAR is an active sensor, it can record images at all times of day and in all weather conditions, making it ideally suited for this task. While with the newer generation of SAR satellites such as TerraSAR-X or COSMOSkyMed amplitude change detection has become possible even for urban areas, interferometric phase change detection has not been published widely. This is mainly because of the long revisit times of common SAR sensors leading to temporal decorrelation. This situation has changed dramatically with the advent of the TanDEM-X constellation, which can create single-pass interferograms from space at very high resolutions, avoiding temporal decorrelation almost completely. In this paper the basic structures that are present for any building in InSAR phases, i.e. layover, shadow, and roof areas, are examined. Approaches for their extraction from TanDEM-X interferograms are developed using simulated SAR interferograms. The extracted features of the building signature will in the future be used for urban change detection in real TanDEM-X High Resolution Spotlight interferograms.

Assembly of the mitochondrial membrane system. XVIII. Genetic loci on mitochondrial DNA involved in cytochrome b biosynthesis.

PubMed

Tzagoloff, A; Foury, F; Akai, A

1976-11-24

1. Fourteen cytoplasmic mutants of Saccharomyces cerevisiae with a specific deficiency of cytochrome b have been studied. The mutations have been shown to occur in two separate genetic loci, COB 1 and COB 2. These loci can be distinguished by mit- X mit- crosses. Pairwise crosses of cytochrome b mutants belonging to different loci yield 4-6% wild type recombinants corresponding to recombinational frequencies of 8-12%. In intra-locus crosses, the recombinational frequencies range from 1% to less than 0.01%. The two loci can also be distinguished by mit- X rho- crosses. Twenty rho- testers have been isolated of which ten preferentially restore mutations in COB 1 and ten others in COB 2. 2. The COB 1 and COB 2 loci have been localized on mitochondrial DNA between the two antibiotic resistance loci OLI 1 and OLI 2 in the order OLI 2-COB 2-COB 1-OLI 1. The results of mit- X mit- and mit- X rho- crosses have also been used to map the cytochrome b mutations relative to each other. The maps obtained by the two independent methods are in good agreement. 3. Mutations in COB 1 have been found to be linked to the OLI1 locus in some but not in other strains of S. cervisiae. This evidence suggests that there may be a spacer region between the two loci whose length varies from strain to strain. 4. Two mutations in COB 2 have been found to cause a loss of a mitochondrial translation product corresponding to the cytochrome b apoprotein. Instead of the wild type protein the mutants have a new low-molecular weight product which is probably a fragment of cytochrome b. The fact that the mutations revert suggests that they are nonsense mutations in the structural gene of cytochrome b.

Elevation validation and geomorphic metric comparison with focus on ASTER GDEM2, SRTM- C, ALOS World 3D, and TanDEM-X

NASA Astrophysics Data System (ADS)

Purinton, Benjamin; Bookhagen, Bodo

2017-04-01

Geomorphologists use digital elevation models (DEMs) to quantify changes in topography - often without rigorous accuracy assessments. In this study we validate and compare elevation accuracy and derived geomorphic metrics from the current generation of satellite-derived DEMs on the southern Central Andean Plateau. The average elevation of 3.7 km, diverse topography and relief, lack of vegetation, and clear skies create ideal conditions for remote sensing in this study area. DEMs at resolutions of 5-30 m are sourced from open-access, research agreement, and commercial outlets, with a focus on the 30 m SRTM-C, 30 m ASTER GDEM2, 12 m TanDEM-X, and 5 m ALOS World 3D data. In addition to these edited products, manually generated DEMs included 10 m single-CoSSC TerraSAR-X / TanDEM-X DEMs and a 30 m stacked ASTER L1A stereopair DEM. We assessed vertical accuracy by comparing standard deviations (SD) of the DEM elevation versus 307,509 differential GPS (dGPS) measurements with < 0.5 m vertical accuracy, acquired across 4,000 m of elevation. Vertical SD was 3.33 m, 9.48 m, 6.93 m, 1.97 m, 2.02-3.83 m, and 1.64 m for the 30 m SRTM-C, 30 m ASTER GDEM2, 30 m stacked ASTER, 12 m TanDEM-X, 10 m single-CoSSC TerraSAR-X / TanDEM-X DEMs, and 5 m ALOS World 3D, respectively. Analysis of vertical uncertainty with respect to terrain elevation, slope, and aspect revealed the high performance across these attributes of the 30 m SRTM-C, 12 m TanDEM-X, and 5 m ALOS World 3D DEMs. The 10 m single-CoSSC TerraSAR-X / TanDEM-X DEMs and the 30 m ASTER GDEM2 displayed slight aspect biases, which were removed in their stacked counterparts (TanDEM-X and the stacked ASTER DEMs). We selected the high quality 30 m SRTM-C, 12 m TanDEM-X, and 5 m ALOS World 3D for geomorphic metric comparison in a 66 sqkm catchment with a clear river knickpoint. For trunk channel profiles analyzed with chi plots, consistent m/n values of 0.49-0.57 were found regardless of DEM resolution or SD. Hillslopes were analyzed

Automatic relative RPC image model bias compensation through hierarchical image matching for improving DEM quality

NASA Astrophysics Data System (ADS)

Noh, Myoung-Jong; Howat, Ian M.

2018-02-01

The quality and efficiency of automated Digital Elevation Model (DEM) extraction from stereoscopic satellite imagery is critically dependent on the accuracy of the sensor model used for co-locating pixels between stereo-pair images. In the absence of ground control or manual tie point selection, errors in the sensor models must be compensated with increased matching search-spaces, increasing both the computation time and the likelihood of spurious matches. Here we present an algorithm for automatically determining and compensating the relative bias in Rational Polynomial Coefficients (RPCs) between stereo-pairs utilizing hierarchical, sub-pixel image matching in object space. We demonstrate the algorithm using a suite of image stereo-pairs from multiple satellites over a range stereo-photogrammetrically challenging polar terrains. Besides providing a validation of the effectiveness of the algorithm for improving DEM quality, experiments with prescribed sensor model errors yield insight into the dependence of DEM characteristics and quality on relative sensor model bias. This algorithm is included in the Surface Extraction through TIN-based Search-space Minimization (SETSM) DEM extraction software package, which is the primary software used for the U.S. National Science Foundation ArcticDEM and Reference Elevation Model of Antarctica (REMA) products.

Discrete Element Modeling (DEM) of Triboelectrically Charged Particles: Revised Experiments

NASA Technical Reports Server (NTRS)

Hogue, Michael D.; Calle, Carlos I.; Curry, D. R.; Weitzman, P. S.

2008-01-01

In a previous work, the addition of basic screened Coulombic electrostatic forces to an existing commercial discrete element modeling (DEM) software was reported. Triboelectric experiments were performed to charge glass spheres rolling on inclined planes of various materials. Charge generation constants and the Q/m ratios for the test materials were calculated from the experimental data and compared to the simulation output of the DEM software. In this paper, we will discuss new values of the charge generation constants calculated from improved experimental procedures and data. Also, planned work to include dielectrophoretic, Van der Waals forces, and advanced mechanical forces into the software will be discussed.

Knocking down mitochondrial iron transporter (MIT) reprograms primary and secondary metabolism in rice plants

PubMed Central

Vigani, Gianpiero; Bashir, Khurram; Ishimaru, Yasuhiro; Lehmann, Martin; Casiraghi, Fabio Marco; Nakanishi, Hiromi; Seki, Motoaki; Geigenberger, Peter; Zocchi, Graziano; Nishizawa, Naoko K.

2016-01-01

Iron (Fe) is an essential micronutrient for plant growth and development, and its reduced bioavailability strongly impairs mitochondrial functionality. In this work, the metabolic adjustment in the rice (Oryza sativa) mitochondrial Fe transporter knockdown mutant (mit-2) was analysed. Biochemical characterization of purified mitochondria from rice roots showed alteration in the respiratory chain of mit-2 compared with wild-type (WT) plants. In particular, proteins belonging to the type II alternative NAD(P)H dehydrogenases accumulated strongly in mit-2 plants, indicating that alternative pathways were activated to keep the respiratory chain working. Additionally, large-scale changes in the transcriptome and metabolome were observed in mit-2 rice plants. In particular, a strong alteration (up-/down-regulation) in the expression of genes encoding enzymes of both primary and secondary metabolism was found in mutant plants. This was reflected by changes in the metabolic profiles in both roots and shoots of mit-2 plants. Significant alterations in the levels of amino acids belonging to the aspartic acid-related pathways (aspartic acid, lysine, and threonine in roots, and aspartic acid and ornithine in shoots) were found that are strictly connected to the Krebs cycle. Furthermore, some metabolites (e.g. pyruvic acid, fumaric acid, ornithine, and oligosaccharides of the raffinose family) accumulated only in the shoot of mit-2 plants, indicating possible hypoxic responses. These findings suggest that the induction of local Fe deficiency in the mitochondrial compartment of mit-2 plants differentially affects the transcript as well as the metabolic profiles in root and shoot tissues. PMID:26685186

Scratch that: MIT's Mitchel Resnick Says Kids Should Do It for Themselves

ERIC Educational Resources Information Center

Traylor, Scott

2008-01-01

Mitchel Resnick is a researcher, inventor, and professor at MIT's Media Laboratory in Cambridge, MA, and the founder of the Lifelong Kindergarten Group at MIT. He is the lead innovator behind many cutting-edge learning technologies and projects for children, including the Computer Clubhouse, PicoCrickets, and the wildly successful consumer…

MIT Lincoln Laboratory Annual Report 2013

DTIC Science & Technology

2013-01-01

A small-scale demonstration FPGA is currently being fabricated in the Microelectronics Laboratory, and a larger array is being designed for fabri ...year, the first Friday of February is a day to call attention to heart disease . Efforts of the six-member team, MIT Lincoln Laboratory for the Heart

Tropical-forest biomass estimation at X-Band from the spaceborne TanDEM-X interferometer

Treesearch

R. Treuhaft; F. Goncalves; J.R. dos Santos; M. Keller; M. Palace; S.N. Madsen; F. Sullivan; P.M.L.A. Graca

2014-01-01

This letter reports the sensitivity of X-band interferometric synthetic aperture radar (InSAR) data from the first dual-spacecraft radar interferometer, TanDEM-X, to variations in tropical-forest aboveground biomass (AGB). It also reports the first tropical-forest AGB estimates fromTanDEM-X data. Tropical forests account for...

MIT-Skywalker: Evaluating comfort of bicycle/saddle seat.

PubMed

Goncalves, Rogerio S; Hamilton, Taya; Daher, Ali R; Hirai, Hiroaki; Krebs, Hermano I

2017-07-01

The MIT-Skywalker is a robotic device developed for the rehabilitation of gait and balance after a neurological injury. This device has been designed based on the concept of a passive walker and provides three distinct training modes: discrete movement, rhythmic movement, and balance training. In this paper, we present our efforts to evaluate the comfort of a bicycle/saddle seat design for the system's novel actuated body weight support device. We employed different bicycle and saddle seats and evaluated comfort using objective and subjective measures. Here we will summarize the results obtained from a study of fifteen healthy subjects and one stroke patient that led to the selection of a saddle seat design for the MIT-Skywalker.

Assessing International Product Design and Development Graduate Courses: The MIT-Portugal Program

ERIC Educational Resources Information Center

Dori, Yehudit Judy; Silva, Arlindo

2010-01-01

The Product Design and Development (PDD) course is part of the graduate curriculum in the Engineering Design and Advanced Manufacturing (EDAM) study in the MIT-Portugal Program. The research participants included about 110 students from MIT, EDAM, and two universities in Portugal, Instituto Superior Técnico-Universidade Técnica de Lisboa (IST) and…

The MIT Program, Competition, and Ethics

NASA Astrophysics Data System (ADS)

Bradt, Hale V.

2013-01-01

The MIT program in x-ray astronomy was, and still is, diverse and productive. Bruno Rossi and later George Clark, as the nominal leaders of the “x-ray astronomy group” created a “hands-off” culture wherein individual researchers could develop their own independent programs. Walter Lewin, Claude Canizares, and I as well as those in the next academic generations, e.g., Saul Rappaport and George Ricker, were able to thrive in this environment. MIT researchers were principal investigators or providers of x-ray instruments on sounding rockets and balloons in the 1960s and then in later years on nine satellite missions, OSO-7, SAS-3, HEAO-1, Einstein, ASCA, RXTE, Chandra, HETE-2, and Suzaku. Such a diverse program involved collaborations with other institutions and of course striving for primacy in discovery and competition for NASA resources. Looking back, I see a high degree of ethical behavior among the observational x-ray community during those years. In competition, we remembered that we might well be collaborating the following year and behaved accordingly. Many of us in the x-ray community had been friends since graduate school days and did not want to lose those relationships. Am I viewing the past through rose colored glasses? I think not. A vignette on this topic: In 1967, I was debating vigorously with Herb Gursky of AS&E about which institution, MIT or AS&E, should be the lead on the fourth paper (Oda et al. 1967, ApJ 148, L5) based on data from the 1966 AS&E rocket flight which had led to Allan Sandage’s (and Japanese) identification of Sco X-1 (Sandage, et al. 1966, ApJ. 146, 316). I and my Italian colleague, Gianfranco Spada, and our Japanese colleague, Minoru Oda, both then visiting MIT, had actively supported that flight. After one rather heated discussion with Herb about this, - I was the heated one; he always remained calm - he left my office saying: “Hale, however this comes out, let’s remain friends.” I treasured that comment and

MIT Lincoln Laboratory 2011 Facts

DTIC Science & Technology

2011-01-01

currently valid OMB control number. 1. REPORT DATE 2011 2. REPORT TYPE 3. DATES COVERED 00-00-2011 to 00-00-2011 4. TITLE AND SUBTITLE MIT Lincoln...primary mission areas—space control ; air and missile defense; communication systems; intelligence, surveillance, and reconnaissance systems; advanced...electronics; tactical systems; homeland protection and chemical and biological defense; cyber security; and air traffic control . Two of the

High-accuracy single-pass InSAR DEM for large-scale flood hazard applications

NASA Astrophysics Data System (ADS)

Schumann, G.; Faherty, D.; Moller, D.

2017-12-01

In this study, we used a unique opportunity of the GLISTIN-A (NASA airborne mission designed to characterizing the cryosphere) track to Greenland to acquire a high-resolution InSAR DEM of a large area in the Red River of the North Basin (north of Grand Forks, ND, USA), which is a very flood-vulnerable valley, particularly in spring time due to increased soil moisture content near state of saturation and/or, typical for this region, snowmelt. Having an InSAR DEM that meets flood inundation modeling and mapping requirements comparable to LiDAR, would demonstrate great application potential of new radar technology for national agencies with an operational flood forecasting mandate and also local state governments active in flood event prediction, disaster response and mitigation. Specifically, we derived a bare-earth DEM in SAR geometry by first removing the inherent far range bias related to airborne operation, which at the more typical large-scale DEM resolution of 30 m has a sensor accuracy of plus or minus 2.5 cm. Subsequently, an intelligent classifier based on informed relationships between InSAR height, intensity and correlation was used to distinguish between bare-earth, roads or embankments, buildings and tall vegetation in order to facilitate the creation of a bare-earth DEM that would meet the requirements for accurate floodplain inundation mapping. Using state-of-the-art LiDAR terrain data, we demonstrate that capability by achieving a root mean squared error of approximately 25 cm and further illustrating its applicability to flood modeling.

Quality assessment of Digital Elevation Model (DEM) in view of the Altiplano hydrological modeling

NASA Astrophysics Data System (ADS)

Satgé, F.; Arsen, A.; Bonnet, M.; Timouk, F.; Calmant, S.; Pilco, R.; Molina, J.; Lavado, W.; Crétaux, J.; HASM

2013-05-01

Topography is crucial data input for hydrological modeling but in many regions of the world, the only way to characterize topography is the use of satellite-based Digital Elevation Models (DEM). In some regions, the quality of these DEMs remains poor and induces modeling errors that may or not be compensated by model parameters tuning. In such regions, the evaluation of these data uncertainties is an important step in the modeling procedure. In this study, which focuses on the Altiplano region, we present the evaluation of the two freely available DEM. The shuttle radar topographic mission (SRTM), a product of the National Aeronautics and Space Administration (NASA) and the Advanced Space Born Thermal Emission and Reflection Global Digital Elevation Map (ASTER GDEM), data provided by the Ministry of Economy, Trade and Industry of Japan (MESI) in collaboration with the NASA, are widely used. While the first represents a resolution of 3 arc seconds (90m) the latter is 1 arc second (30m). In order to select the most reliable DEM, we compared the DEM elevation with high qualities control points elevation. Because of its large spatial coverture (track spaced of 30 km with a measure of each 172 m) and its high vertical accuracy which is less than 15 cm in good weather conditions, the Geoscience Laser Altimeter System (GLAS) on board on the Ice, Cloud and Land elevation Satellite of NASA (ICESat) represent the better solution to establish a high quality elevation database. After a quality check, more than 150 000 ICESat/GLAS measurements are suitable in terms of accuracy for the Altiplano watershed. This data base has been used to evaluate the vertical accuracy for each DEM. Regarding to the full spatial coverture; the comparison has been done for both, all kind of land coverture, range altitude and mean slope.

Knocking down mitochondrial iron transporter (MIT) reprograms primary and secondary metabolism in rice plants.

PubMed

Vigani, Gianpiero; Bashir, Khurram; Ishimaru, Yasuhiro; Lehmann, Martin; Casiraghi, Fabio Marco; Nakanishi, Hiromi; Seki, Motoaki; Geigenberger, Peter; Zocchi, Graziano; Nishizawa, Naoko K

2016-03-01

Iron (Fe) is an essential micronutrient for plant growth and development, and its reduced bioavailability strongly impairs mitochondrial functionality. In this work, the metabolic adjustment in the rice (Oryza sativa) mitochondrial Fe transporter knockdown mutant (mit-2) was analysed. Biochemical characterization of purified mitochondria from rice roots showed alteration in the respiratory chain of mit-2 compared with wild-type (WT) plants. In particular, proteins belonging to the type II alternative NAD(P)H dehydrogenases accumulated strongly in mit-2 plants, indicating that alternative pathways were activated to keep the respiratory chain working. Additionally, large-scale changes in the transcriptome and metabolome were observed in mit-2 rice plants. In particular, a strong alteration (up-/down-regulation) in the expression of genes encoding enzymes of both primary and secondary metabolism was found in mutant plants. This was reflected by changes in the metabolic profiles in both roots and shoots of mit-2 plants. Significant alterations in the levels of amino acids belonging to the aspartic acid-related pathways (aspartic acid, lysine, and threonine in roots, and aspartic acid and ornithine in shoots) were found that are strictly connected to the Krebs cycle. Furthermore, some metabolites (e.g. pyruvic acid, fumaric acid, ornithine, and oligosaccharides of the raffinose family) accumulated only in the shoot of mit-2 plants, indicating possible hypoxic responses. These findings suggest that the induction of local Fe deficiency in the mitochondrial compartment of mit-2 plants differentially affects the transcript as well as the metabolic profiles in root and shoot tissues. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

Arctic Digital Elevation Models (DEMs) generated by Surface Extraction from TIN-Based Searchspace Minimization (SETSM) algorithm from RPCs-based Imagery

NASA Astrophysics Data System (ADS)

Noh, M. J.; Howat, I. M.; Porter, C. C.; Willis, M. J.; Morin, P. J.

2016-12-01

The Arctic is undergoing rapid change associated with climate warming. Digital Elevation Models (DEMs) provide critical information for change measurement and infrastructure planning in this vulnerable region, yet the existing quality and coverage of DEMs in the Arctic is poor. Low contrast and repeatedly-textured surfaces, such as snow and glacial ice and mountain shadows, all common in the Arctic, challenge existing stereo-photogrammetric techniques. Submeter resolution, stereoscopic satellite imagery with high geometric and radiometric quality, and wide spatial coverage are becoming increasingly accessible to the scientific community. To utilize these imagery for extracting DEMs at a large scale over glaciated and high latitude regions we developed the Surface Extraction from TIN-based Searchspace Minimization (SETSM) algorithm. SETSM is fully automatic (i.e. no search parameter settings are needed) and uses only the satellite rational polynomial coefficients (RPCs). Using SETSM, we have generated a large number of DEMs (> 100,000 scene pair) from WorldView, GeoEye and QuickBird stereo images collected by DigitalGlobe Inc. and archived by the Polar Geospatial Center (PGC) at the University of Minnesota through an academic licensing program maintained by the US National Geospatial-Intelligence Agency (NGA). SETSM is the primary DEM generation software for the US National Science Foundation's ArcticDEM program, with the objective of generating high resolution (2-8m) topography for the entire Arctic landmass, including seamless DEM mosaics and repeat DEM strips for change detection. ArcticDEM is collaboration between multiple US universities, governmental agencies and private companies, as well as international partners assisting with quality control and registration. ArcticDEM is being produced using the petascale Blue Waters supercomputer at the National Center for Supercomputer Applications at the University of Illinois. In this paper, we introduce the SETSM

Aster Global dem Version 3, and New Aster Water Body Dataset

NASA Astrophysics Data System (ADS)

Abrams, M.

2016-06-01

In 2016, the US/Japan ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer) project released Version 3 of the Global DEM (GDEM). This 30 m DEM covers the earth's surface from 82N to 82S, and improves on two earlier versions by correcting some artefacts and filling in areas of missing DEMs by the acquisition of additional data. The GDEM was produced by stereocorrelation of 2 million ASTER scenes and operation on a pixel-by-pixel basis: cloud screening; stacking data from overlapping scenes; removing outlier values, and averaging elevation values. As previously, the GDEM is packaged in ~ 23,000 1 x 1 degree tiles. Each tile has a DEM file, and a NUM file reporting the number of scenes used for each pixel, and identifying the source for fill-in data (where persistent clouds prevented computation of an elevation value). An additional data set was concurrently produced and released: the ASTER Water Body Dataset (AWBD). This is a 30 m raster product, which encodes every pixel as either lake, river, or ocean; thus providing a global inland and shore-line water body mask. Water was identified through spectral analysis algorithms and manual editing. This product was evaluated against the Shuttle Water Body Dataset (SWBD), and the Landsat-based Global Inland Water (GIW) product. The SWBD only covers the earth between about 60 degrees north and south, so it is not a global product. The GIW only delineates inland water bodies, and does not deal with ocean coastlines. All products are at 30 m postings.

The Shuttle Radar Topography Mission: A Global DEM

NASA Technical Reports Server (NTRS)

Farr, Tom G.; Kobrick, Mike

2000-01-01

Digital topographic data are critical for a variety of civilian, commercial, and military applications. Scientists use Digital Elevation Models (DEM) to map drainage patterns and ecosystems, and to monitor land surface changes over time. The mountain-building effects of tectonics and the climatic effects of erosion can also be modeled with DEW The data's military applications include mission planning and rehearsal, modeling and simulation. Commercial applications include determining locations for cellular phone towers, enhanced ground proximity warning systems for aircraft, and improved maps for backpackers. The Shuttle Radar Topography Mission (SRTM) (Fig. 1), is a cooperative project between NASA and the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense. The mission is designed to use a single-pass radar interferometer to produce a digital elevation model of the Earth's land surface between about 60 degrees north and south latitude. The DEM will have 30 m pixel spacing and about 15 m vertical errors.

Himmelsfotografie MIT Schmidt-Teleskopen

NASA Astrophysics Data System (ADS)

Marx, Siegfried; Pfau, Werner

Auf dem Höhepunkt der Verbreitung und astronomischen Anwendung von Schmidt-Teleskopen legen S. Marx und W. Pfau einen reich illustrierten Bildband zu diesem Fernrohrtyp vor. Der thematische Bogen reicht von der Teleskoptechnik und ihrer Geschichte über das Leben von Berhard Schmidt bis zu den schönsten, hier in hervorragender Qualität wiedergegebenen Himmelsaufnahmen und ihrer wissenschaftlichen Interpretation. Praktische Hinweise zu eigener fotografischer Tätigkeit und ein Glossar machen das Buch nützlich für jeden Liebhaber der Himmelskunde.

[Postoperative adjuvante Therapie mit einem Mistelextrakt (Viscum album ssp. album) bei Hündinnen mit Mammatumoren].

PubMed

Biegel, Ulrike; Stratmann, Nina; Knauf, Yvonne; Ruess, Katja; Reif, Marcus; Wehrend, Axel

2017-01-01

Hintergrund: Canine Mammatumoren (CMT) sind wegen ihrer Häufigkeit und hohen Malignitätsrate eine Herausforderung für die Veterinärmedizin. Bisher ist noch keine postoperative adjuvante Therapie als wirksamer Standard etabliert und in den nächsten Jahren wohl auch nicht zu erwarten. Zusätzlich ist die Frage nach der Verträglichkeit einer adjuvanten Therapie mit Erhaltung oder Verbesserung der Lebensqualität (LQ) wichtig. Die Therapie mit Mistelextrakten (Viscum album L.; VAE) ist in der Humanonkologie nach adjuvanter Tumorbasistherapie (Chemotherapie und Bestrahlung) eine sehr häufig verwendete, zusätzliche adjuvante Behandlungsmethode. Auch bei verschiedenen Tierarten werden inzwischen Mistelpräparate in der Onkologie erfolgreich angewendet. Methoden: Überprüfung von Wirkung und Nutzen einer postoperativen, adjuvanten Misteltherapie beim CMT sowie Erfassung der LQ unter der VAE-Behandlung. Ausgewertet wurden 56 Hündinnen mit Mammaadenokarzinom, 33 ausschließlich operierte Kontrolltiere und 23 operierte Tiere, die adjuvant VAE erhielten. Ergebnisse: Die mediane Überlebenszeit (MST) aller Tiere (n = 56) betrug 32 Monate (Interquartilbereich 13-51 Monate). Im deskriptiven Vergleich der Überlebenszeiten (ST) nach Kaplan-Meier waren nach 12, 24, 36 bzw. 48 Monaten noch 24, 20, 15 bzw. 5 Hündinnen (entsprechend 72,7%, 60,6%, 45,1%, 12,4%) der Kontrollgruppe sowie 19, 14, 11 und 1 Hündin (82,6%, 60,9%, 47,8%, 4,3%) der VAE-Gruppe am Leben. Die VAE-Therapie führte zu einem geringeren Gesamtversterberisiko, das statistisch nicht signifikant war (Hazard Ratio (HR) 0,530, 95%-Konfidenzintervall (KI) 0,222-1,262; p = 0,15). Tendenziell (p = 0,07) zeigte sich eine Verringerung des tumorbedingten Sterberisikos auf 25% (HR 0,251, 95%-KI 0,056-1,122). Schlussfolgerungen: Es kann eine Tendenz zur Senkung des tumorbedingten Sterberisikos der VAE-Gruppe bei guter Verträglichkeit der Therapie angenommen werden. Die LQ der Tiere blieb über die gesamte

Automated sinkhole detection using a DEM subsetting technique and fill tools at Mammoth Cave National Park

NASA Astrophysics Data System (ADS)

Wall, J.; Bohnenstiehl, D. R.; Levine, N. S.

2013-12-01

An automated workflow for sinkhole detection is developed using Light Detection and Ranging (Lidar) data from Mammoth Cave National Park (MACA). While the park is known to sit within a karst formation, the generally dense canopy cover and the size of the park (~53,000 acres) creates issues for sinkhole inventorying. Lidar provides a useful remote sensing technology for peering beneath the canopy in hard to reach areas of the park. In order to detect sinkholes, a subsetting technique is used to interpolate a Digital Elevation Model (DEM) thereby reducing edge effects. For each subset, standard GIS fill tools are used to fill depressions within the DEM. The initial DEM is then subtracted from the filled DEM resulting in detected depressions or sinkholes. Resulting depressions are then described in terms of size and geospatial trend.

Sedimentary Environments Mapping in the Yellow Sea Using TanDEM-X and Optic Satellites

NASA Astrophysics Data System (ADS)

Ryu, J. H.; Lee, Y. K.; Kim, S. W.

2017-12-01

Due to land reclamation and dredging, 57% of China's coastal wetlands have disappeared since the 1950s, and the total area of tidal flats in South Korea decreased from approximately 2,800km2 in 1990 to 2392km2 in 2005(Qiu, 2011 and MLTM, 2010). Intertidal DEM and sedimentary facies are useful for understanding intertidal functions and monitoring their response to natural and anthropogenic actions. Highly accurate intertidal DEMs with 5-m resolution were generated based on the TanDEM-X interferometric SAR (InSAR) technique because TanDEM-X allows the acquisition of the coherent InSAR pairs with no time lag or approximately 10-second temporal baseline between master and slave SAR image. We successfully generated intertidal zone DEMs with 5-7-m spatial resolutions and interferometric height accuracies better than 0.15 m for three representative tidal flats on the west coast of the Korean Peninsula and one site of chinese coastal region in the Yellow Sea. Surface sediment classification based on remotely sensed data must circumspectly consider an effective critical grain size, water content, local topography, and intertidal structures. The earlier studies have some limitation that the classification map is not considered to analysis various environmental conditions. Therefore, the purpose of this study was minutely to mapping the surface sedimentary facies by analyzing the tidal channel, topography with multi-sensor remotely sensed data and in-situ data.

MIT gets good marks for fighting gender discrimination

NASA Astrophysics Data System (ADS)

Gwynne, Peter

2011-05-01

The Massachusetts Institute of Technology (MIT) has made "significant progress" in increasing the number of female faculty members, with their numbers in science and engineering almost doubling over the last decade.

Binding of Substrates to the Central Pore of the Vps4 ATPase Is Autoinhibited by the Microtubule Interacting and Trafficking (MIT) Domain and Activated by MIT Interacting Motifs (MIMs).

PubMed

Han, Han; Monroe, Nicole; Votteler, Jörg; Shakya, Binita; Sundquist, Wesley I; Hill, Christopher P

2015-05-22

The endosomal sorting complexes required for transport (ESCRT) pathway drives reverse topology membrane fission events within multiple cellular pathways, including cytokinesis, multivesicular body biogenesis, repair of the plasma membrane, nuclear membrane vesicle formation, and HIV budding. The AAA ATPase Vps4 is recruited to membrane necks shortly before fission, where it catalyzes disassembly of the ESCRT-III lattice. The N-terminal Vps4 microtubule-interacting and trafficking (MIT) domains initially bind the C-terminal MIT-interacting motifs (MIMs) of ESCRT-III subunits, but it is unclear how the enzyme then remodels these substrates in response to ATP hydrolysis. Here, we report quantitative binding studies that demonstrate that residues from helix 5 of the Vps2p subunit of ESCRT-III bind to the central pore of an asymmetric Vps4p hexamer in a manner that is dependent upon the presence of flexible nucleotide analogs that can mimic multiple states in the ATP hydrolysis cycle. We also find that substrate engagement is autoinhibited by the Vps4p MIT domain and that this inhibition is relieved by binding of either Type 1 or Type 2 MIM elements, which bind the Vps4p MIT domain through different interfaces. These observations support the model that Vps4 substrates are initially recruited by an MIM-MIT interaction that activates the Vps4 central pore to engage substrates and generate force, thereby triggering ESCRT-III disassembly. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

Binding of Substrates to the Central Pore of the Vps4 ATPase Is Autoinhibited by the Microtubule Interacting and Trafficking (MIT) Domain and Activated by MIT Interacting Motifs (MIMs)*

PubMed Central

Han, Han; Monroe, Nicole; Votteler, Jörg; Shakya, Binita; Sundquist, Wesley I.; Hill, Christopher P.

2015-01-01

The endosomal sorting complexes required for transport (ESCRT) pathway drives reverse topology membrane fission events within multiple cellular pathways, including cytokinesis, multivesicular body biogenesis, repair of the plasma membrane, nuclear membrane vesicle formation, and HIV budding. The AAA ATPase Vps4 is recruited to membrane necks shortly before fission, where it catalyzes disassembly of the ESCRT-III lattice. The N-terminal Vps4 microtubule-interacting and trafficking (MIT) domains initially bind the C-terminal MIT-interacting motifs (MIMs) of ESCRT-III subunits, but it is unclear how the enzyme then remodels these substrates in response to ATP hydrolysis. Here, we report quantitative binding studies that demonstrate that residues from helix 5 of the Vps2p subunit of ESCRT-III bind to the central pore of an asymmetric Vps4p hexamer in a manner that is dependent upon the presence of flexible nucleotide analogs that can mimic multiple states in the ATP hydrolysis cycle. We also find that substrate engagement is autoinhibited by the Vps4p MIT domain and that this inhibition is relieved by binding of either Type 1 or Type 2 MIM elements, which bind the Vps4p MIT domain through different interfaces. These observations support the model that Vps4 substrates are initially recruited by an MIM-MIT interaction that activates the Vps4 central pore to engage substrates and generate force, thereby triggering ESCRT-III disassembly. PMID:25833946

Evaluation of TanDEM-X elevation data for geomorphological mapping and interpretation in high mountain environments - A case study from SE Tibet, China

NASA Astrophysics Data System (ADS)

Pipaud, Isabel; Loibl, David; Lehmkuhl, Frank

2015-10-01

Digital elevation models (DEMs) are a prerequisite for many different applications in the field of geomorphology. In this context, the two near-global medium resolution DEMs originating from the SRTM and ASTER missions are widely used. For detailed geomorphological studies, particularly in high mountain environments, these datasets are, however, known to have substantial disadvantages beyond their posting, i.e., data gaps and miscellaneous artifacts. The upcoming TanDEM-X DEM is a promising candidate to improve this situation by application of state-of-the-art radar technology, exhibiting a posting of 12 m and less proneness to errors. In this study, we present a DEM processed from a single TanDEM-X CoSSC scene, covering a study area in the extreme relief of the eastern Nyainqêntanglha Range, southeastern Tibet. The potential of the resulting experimental TanDEM-X DEM for geomorphological applications was evaluated by geomorphometric analyses and an assessment of landform cognoscibility and artifacts in comparison to the ASTER GDEM and the recently released SRTM 1″ DEM. Detailed geomorphological mapping was conducted for four selected core study areas in a manual approach, based exclusively on the TanDEM-X DEM and its basic derivates. The results show that the self-processed TanDEM-X DEM yields a detailed and widely consistent landscape representation. It thus fosters geomorphological analysis by visual and quantitative means, allowing delineation of landforms down to footprints of 30 m. Even in this premature state, the TanDEM-X elevation data are widely superior to the ASTER and SRTM datasets, primarily owing to its significantly higher resolution and its lower susceptibility to artifacts that hamper landform interpretation. Conversely, challenges toward interferometric DEM generation were identified, including (i) triangulation facets and missing topographic information resulting from radar layover on steep slopes facing toward the radar sensor, (ii) low

FE-DEM Analysis of the Effect of Tread Pattern on the Tractive Performance of Tires Operating on Sand

NASA Astrophysics Data System (ADS)

Nakashima, Hiroshi; Takatsu, Yuzuru; Shinone, Hisanori; Matsukawa, Hisao; Kasetani, Takahiro

Soil-tire system interaction is a fundamental and important research topic in terramechanics. We applied a 2D finite element, discrete element method (FE-DEM), using FEM for the tire and the bottom soil layer and DEM for the surface soil layer. Satisfactory performance analysis was achieved. In this study, to clarify the capabilities and limitations of the method for soil-tire interaction analysis, the tractive performance of real automobile tires with two different tread patterns—smooth and grooved—was analyzed by FE-DEM, and the numerical results compared with the experimental results obtained using an indoor traction measurement system. The analysis of tractive performance could be performed with sufficient accuracy by the proposed 2D dynamic FE-DEM. FE-DEM obtained larger drawbar pull for a tire with a grooved tread pattern, which was verified by the experimental results. Moreover, the result for the grooved tire showed almost the same gross tractive effort and similar running resistance as in experiments. However, for a tire with smooth tread pattern, the analyzed gross tractive effort and running resistance behaved differently than the experimental results, largely due to the difference in tire sinkage in FE-DEM.

Extracting DEM from airborne X-band data based on PolInSAR

NASA Astrophysics Data System (ADS)

Hou, X. X.; Huang, G. M.; Zhao, Z.

2015-06-01

Polarimetric Interferometric Synthetic Aperture Radar (PolInSAR) is a new trend of SAR remote sensing technology which combined polarized multichannel information and Interferometric information. It is of great significance for extracting DEM in some regions with low precision of DEM such as vegetation coverage area and building concentrated area. In this paper we describe our experiments with high-resolution X-band full Polarimetric SAR data acquired by a dual-baseline interferometric airborne SAR system over an area of Danling in southern China. Pauli algorithm is used to generate the double polarimetric interferometry data, Singular Value Decomposition (SVD), Numerical Radius (NR) and Phase diversity (PD) methods are used to generate the full polarimetric interferometry data. Then we can make use of the polarimetric interferometric information to extract DEM with processing of pre filtering , image registration, image resampling, coherence optimization, multilook processing, flat-earth removal, interferogram filtering, phase unwrapping, parameter calibration, height derivation and geo-coding. The processing system named SARPlore has been exploited based on VC++ led by Chinese Academy of Surveying and Mapping. Finally compared optimization results with the single polarimetric interferometry, it has been observed that optimization ways can reduce the interferometric noise and the phase unwrapping residuals, and improve the precision of DEM. The result of full polarimetric interferometry is better than double polarimetric interferometry. Meanwhile, in different terrain, the result of full polarimetric interferometry will have a different degree of increase.

Volcanic activity at Etna volcano, Sicily, Italy between June 2011 and March 2017 studied with TanDEM-X SAR interferometry

NASA Astrophysics Data System (ADS)

Kubanek, J.; Raible, B.; Westerhaus, M.; Heck, B.

2017-12-01

High-resolution and up-to-date topographic data are of high value in volcanology and can be used in a variety of applications such as volcanic flow modeling or hazard assessment. Furthermore, time-series of topographic data can provide valuable insights into the dynamics of an ongoing eruption. Differencing topographic data acquired at different times enables to derive areal coverage of lava, flow volumes, and lava extrusion rates, the most important parameters during ongoing eruptions for estimating hazard potential, yet most difficult to determine. Anyhow, topographic data acquisition and provision is a challenge. Very often, high-resolution data only exists within a small spatial extension, or the available data is already outdated when the final product is provided. This is especially true for very dynamic landscapes, such as volcanoes. The bistatic TanDEM-X radar satellite mission enables for the first time to generate up-to-date and high-resolution digital elevation models (DEMs) repeatedly using the interferometric phase. The repeated acquisition of TanDEM-X data facilitates the generation of a time-series of DEMs. Differencing DEMs generated from bistatic TanDEM-X data over time can contribute to monitor topographic changes at active volcanoes, and can help to estimate magmatic ascent rates. Here, we use the bistatic TanDEM-X data to investigate the activity of Etna volcano in Sicily, Italy. Etna's activity is characterized by lava fountains and lava flows with ash plumes from four major summit crater areas. Especially the newest crater, the New South East Crater (NSEC) that was formed in 2011 has been highly active in recent years. Over one hundred bistatic TanDEM-X data pairs were acquired between January 2011 and March 2017 in StripMap mode, covering episodes of lava fountaining and lava flow emplacement at Etna's NSEC and its surrounding area. Generating DEMs of every bistatic data pair enables us to assess areal extension of the lava flows, to

Discrete Element Method (DEM) Simulations using PFC3D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matt Evans

Contains input scripts, background information, reduced data, and results associated with the discrete element method (DEM) simulations of interface shear tests, plate anchor pullout tests, and torpedo anchor installation and pullout tests, using the software PFC3D (v4.0).

A description of rotations for DEM models of particle systems

NASA Astrophysics Data System (ADS)

Campello, Eduardo M. B.

2015-06-01

In this work, we show how a vector parameterization of rotations can be adopted to describe the rotational motion of particles within the framework of the discrete element method (DEM). It is based on the use of a special rotation vector, called Rodrigues rotation vector, and accounts for finite rotations in a fully exact manner. The use of fictitious entities such as quaternions or complicated structures such as Euler angles is thereby circumvented. As an additional advantage, stick-slip friction models with inter-particle rolling motion are made possible in a consistent and elegant way. A few examples are provided to illustrate the applicability of the scheme. We believe that simple vector descriptions of rotations are very useful for DEM models of particle systems.

Nanomedical strategy to prolong survival period, heighten cure rate, and lower systemic toxicity of S180 mice treated with MTX/MIT.

PubMed

Song, Ning; Zhao, Ming; Wang, Yuji; Hu, Xi; Wu, Jianhui; Jiang, Xueyun; Li, Shan; Cui, Chunying; Peng, Shiqi

2016-01-01

In spite of the usual combination form of methotrexate (MTX)/mitoxantrone (MIT) and various complex combination regimens of MTX/MIT with other anticancer drugs, the survival period, cure rate, and systemic toxicity still need to be improved. For this purpose, a nanostructured amino group-modified mesoporous silica nanoparticles (MSNN)-MTX/MIT was designed. In the preparation, the surface of mesoporous silica nanoparticles (MSNs) was modified with amino groups to form MSNN. The covalent modification of the amino groups on the surface of MSNN with MTX resulted in MSNN-MTX. The loading of MIT into the surface pores of MSNN-MTX produced nanostructured MSNN-MTX/MIT. Compared with the usual combination form (MTX/MIT), nanostructured MSNN-MTX/MIT increased the survival period greatly, heightened the cure rate to a great extent, and lowered the systemic toxicity of the treated S180 mice, significantly. These superior in vivo properties of nanostructured MSNN-MTX/MIT over the usual combination form (MTX/MIT) were correlated with the former selectively releasing MTX and MIT in tumor tissue and inside cancer cells in vitro. The chemical structure and the nanostructure of MSNN-MTX/MIT were characterized using infrared and differential scanning calorimeter spectra as well as transmission electron microscope images, respectively.

Nanomedical strategy to prolong survival period, heighten cure rate, and lower systemic toxicity of S180 mice treated with MTX/MIT

PubMed Central

Song, Ning; Zhao, Ming; Wang, Yuji; Hu, Xi; Wu, Jianhui; Jiang, Xueyun; Li, Shan; Cui, Chunying; Peng, Shiqi

2016-01-01

In spite of the usual combination form of methotrexate (MTX)/mitoxantrone (MIT) and various complex combination regimens of MTX/MIT with other anticancer drugs, the survival period, cure rate, and systemic toxicity still need to be improved. For this purpose, a nanostructured amino group-modified mesoporous silica nanoparticles (MSNN)−MTX/MIT was designed. In the preparation, the surface of mesoporous silica nanoparticles (MSNs) was modified with amino groups to form MSNN. The covalent modification of the amino groups on the surface of MSNN with MTX resulted in MSNN−MTX. The loading of MIT into the surface pores of MSNN−MTX produced nanostructured MSNN−MTX/MIT. Compared with the usual combination form (MTX/MIT), nanostructured MSNN−MTX/MIT increased the survival period greatly, heightened the cure rate to a great extent, and lowered the systemic toxicity of the treated S180 mice, significantly. These superior in vivo properties of nanostructured MSNN−MTX/MIT over the usual combination form (MTX/MIT) were correlated with the former selectively releasing MTX and MIT in tumor tissue and inside cancer cells in vitro. The chemical structure and the nanostructure of MSNN−MTX/MIT were characterized using infrared and differential scanning calorimeter spectra as well as transmission electron microscope images, respectively. PMID:27621591

How Strong and Weak Readers Perform on the Developmental Eye Movement Test (DEM): Norms for Latvian School-Aged Children

ERIC Educational Resources Information Center

Serdjukova, Jelena; Ekimane, Lasma; Valeinis, Janis; Skilters, Jurgis; Krumina, Gunta

2017-01-01

The aim of our study was to determine DEM test performance norms for school-aged children in Latvia, assess how DEM test results correlate with children's reading rates, compare test performance between strong and weak readers. A modified DEM test and a newly developed reading test were administered to 1487 children during a screening survey. Our…

Mit1 Transcription Factor Mediates Methanol Signaling and Regulates the Alcohol Oxidase 1 (AOX1) Promoter in Pichia pastoris.

PubMed

Wang, Xiaolong; Wang, Qi; Wang, Jinjia; Bai, Peng; Shi, Lei; Shen, Wei; Zhou, Mian; Zhou, Xiangshan; Zhang, Yuanxing; Cai, Menghao

2016-03-18

The alcohol oxidase 1 (AOX1) promoter (P AOX1) of Pichia pastoris is the most powerful and commonly used promoter for driving protein expression. However, mechanisms regulating its transcriptional activity are unclear. Here, we identified a Zn(II)2Cys6-type methanol-induced transcription factor 1 (Mit1) and elucidated its roles in regulating PAOX1 activity in response to glycerol and methanol. Mit1 regulated the expression of many genes involved in methanol utilization pathway, including AOX1, but did not participate in peroxisome proliferation and transportation of peroxisomal proteins during methanol metabolism. Structural analysis of Mit1 by performing domain deletions confirmed its specific and critical role in the strict repression of P AOX1 in glycerol medium. Importantly, Mit1, Mxr1, and Prm1, which positively regulated P AOX1 in response to methanol, were bound to P AOX1 at different sites and did not interact with each other. However, these factors cooperatively activated P AOX1 through a cascade. Mxr1 mainly functioned during carbon derepression, whereas Mit1 and Prm1 functioned during methanol induction, with Prm1 transmitting methanol signal to Mit1 by binding to the MIT1 promoter (P MIT1), thus increasingly expressing Mit1 and subsequently activating P AOX1. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

[R]MIT Research Centre at Delft University of Technology: A Bridge between Research, Education, Society and Profession

ERIC Educational Resources Information Center

Zijlstra, Hielkje

2009-01-01

In 2006, we launched the [R]MIT Research Centre (Modification, Intervention Transformation) at the Faculty of Architecture at Delft University of Technology. [R]MIT was founded to respond to the need for an integrated, multi-disciplinary approach to the transformation of the built environment. [R]MIT aims to bring momentum to the renewal of…

An outlet breaching algorithm for the treatment of closed depressions in a raster DEM

NASA Astrophysics Data System (ADS)

Martz, Lawrence W.; Garbrecht, Jurgen

1999-08-01

Automated drainage analysis of raster DEMs typically begins with the simulated filling of all closed depressions and the imposition of a drainage pattern on the resulting flat areas. The elimination of closed depressions by filling implicitly assumes that all depressions are caused by elevation underestimation. This assumption is difficult to support, as depressions can be produced by overestimation as well as by underestimation of DEM values.This paper presents a new algorithm that is applied in conjunction with conventional depression filling to provide a more realistic treatment of those depressions that are likely due to overestimation errors. The algorithm lowers the elevation of selected cells on the edge of closed depressions to simulate breaching of the depression outlets. Application of this breaching algorithm prior to depression filling can substantially reduce the number and size of depressions that need to be filled, especially in low relief terrain.Removing or reducing the size of a depression by breaching implicitly assumes that the depression is due to a spurious flow blockage caused by elevation overestimation. Removing a depression by filling, on the other hand, implicitly assumes that the depression is a direct artifact of elevation underestimation. Although the breaching algorithm cannot distinguish between overestimation and underestimation errors in a DEM, a constraining parameter for breaching length can be used to restrict breaching to closed depressions caused by narrow blockages along well-defined drainage courses. These are considered the depressions most likely to have arisen from overestimation errors. Applying the constrained breaching algorithm prior to a conventional depression-filling algorithm allows both positive and negative elevation adjustments to be used to remove depressions.The breaching algorithm was incorporated into the DEM pre-processing operations of the TOPAZ software system. The effect of the algorithm is illustrated

Uncertainty modelling and analysis of volume calculations based on a regular grid digital elevation model (DEM)

NASA Astrophysics Data System (ADS)

Li, Chang; Wang, Qing; Shi, Wenzhong; Zhao, Sisi

2018-05-01

The accuracy of earthwork calculations that compute terrain volume is critical to digital terrain analysis (DTA). The uncertainties in volume calculations (VCs) based on a DEM are primarily related to three factors: 1) model error (ME), which is caused by an adopted algorithm for a VC model, 2) discrete error (DE), which is usually caused by DEM resolution and terrain complexity, and 3) propagation error (PE), which is caused by the variables' error. Based on these factors, the uncertainty modelling and analysis of VCs based on a regular grid DEM are investigated in this paper. Especially, how to quantify the uncertainty of VCs is proposed by a confidence interval based on truncation error (TE). In the experiments, the trapezoidal double rule (TDR) and Simpson's double rule (SDR) were used to calculate volume, where the TE is the major ME, and six simulated regular grid DEMs with different terrain complexity and resolution (i.e. DE) were generated by a Gauss synthetic surface to easily obtain the theoretical true value and eliminate the interference of data errors. For PE, Monte-Carlo simulation techniques and spatial autocorrelation were used to represent DEM uncertainty. This study can enrich uncertainty modelling and analysis-related theories of geographic information science.

CFD-DEM modeling the effect of column size and bed height on minimum fluidization velocity in micro fluidized beds with Geldart B particles

DOE PAGES

Xu, Yupeng; Li, Tingwen; Musser, Jordan; ...

2017-06-07

The fluidization behavior of Geldart B particles in micro fluidized beds is investigated numerically using Computational Fluid Dynamics coupled with Discrete Element Method (CFD-DEM) available in the open-source Multiphase Flow with Interphase eXchanges (MFIX) code. The effects of different bed inner diameters (D) of 8 mm, 12 mm, 16 mm and various initial static bed heights (H) were examined. It is found that both decreasing the column diameter and increasing the bed height in a micro fluidized bed increases the minimum fluidization velocity (Umf). The observed overshoot in pressure drop that occurs before the onset of fluidization decreases in magnitudemore » with increasing column diameter, however there is less sensitivity to bed height. Overall, the numerical results agree qualitatively with existing theoretical correlations and experimental studies. The simulations show that both column diameter and particle-wall friction contribute to the variation in minimum fluidization velocity. Finally, these two factors are coupled and hard to separate. The detailed influences of wall friction on minimum fluidization velocity are then investigated for a prescribed column diameter of 8 mm by varying the wall friction from 0 to 0.4.« less

CFD-DEM modeling the effect of column size and bed height on minimum fluidization velocity in micro fluidized beds with Geldart B particles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Yupeng; Li, Tingwen; Musser, Jordan

The fluidization behavior of Geldart B particles in micro fluidized beds is investigated numerically using Computational Fluid Dynamics coupled with Discrete Element Method (CFD-DEM) available in the open-source Multiphase Flow with Interphase eXchanges (MFIX) code. The effects of different bed inner diameters (D) of 8 mm, 12 mm, 16 mm and various initial static bed heights (H) were examined. It is found that both decreasing the column diameter and increasing the bed height in a micro fluidized bed increases the minimum fluidization velocity (Umf). The observed overshoot in pressure drop that occurs before the onset of fluidization decreases in magnitudemore » with increasing column diameter, however there is less sensitivity to bed height. Overall, the numerical results agree qualitatively with existing theoretical correlations and experimental studies. The simulations show that both column diameter and particle-wall friction contribute to the variation in minimum fluidization velocity. Finally, these two factors are coupled and hard to separate. The detailed influences of wall friction on minimum fluidization velocity are then investigated for a prescribed column diameter of 8 mm by varying the wall friction from 0 to 0.4.« less

Mit1 Transcription Factor Mediates Methanol Signaling and Regulates the Alcohol Oxidase 1 (AOX1) Promoter in Pichia pastoris*

PubMed Central

Wang, Xiaolong; Wang, Qi; Wang, Jinjia; Bai, Peng; Shi, Lei; Shen, Wei; Zhou, Mian; Zhou, Xiangshan; Zhang, Yuanxing; Cai, Menghao

2016-01-01

The alcohol oxidase 1 (AOX1) promoter (PAOX1) of Pichia pastoris is the most powerful and commonly used promoter for driving protein expression. However, mechanisms regulating its transcriptional activity are unclear. Here, we identified a Zn(II)2Cys6-type methanol-induced transcription factor 1 (Mit1) and elucidated its roles in regulating PAOX1 activity in response to glycerol and methanol. Mit1 regulated the expression of many genes involved in methanol utilization pathway, including AOX1, but did not participate in peroxisome proliferation and transportation of peroxisomal proteins during methanol metabolism. Structural analysis of Mit1 by performing domain deletions confirmed its specific and critical role in the strict repression of PAOX1 in glycerol medium. Importantly, Mit1, Mxr1, and Prm1, which positively regulated PAOX1 in response to methanol, were bound to PAOX1 at different sites and did not interact with each other. However, these factors cooperatively activated PAOX1 through a cascade. Mxr1 mainly functioned during carbon derepression, whereas Mit1 and Prm1 functioned during methanol induction, with Prm1 transmitting methanol signal to Mit1 by binding to the MIT1 promoter (PMIT1), thus increasingly expressing Mit1 and subsequently activating PAOX1. PMID:26828066

Biotechnology Process Engineering Center at MIT - Overview

Science.gov Websites

laboratories. Biotechnology-related research in the labs of over 15 faculty members in the Biological 60,000 square feet for biotechnology-related engineering research. This centralization and consolidation wider array of equipment and facilities available in other MIT labs and Centers. Some examples include

Coastal Digital Elevation Models (DEMs) for tsunami hazard assessment on the French coasts

NASA Astrophysics Data System (ADS)

Maspataud, Aurélie; Biscara, Laurie; Hébert, Hélène; Schmitt, Thierry; Créach, Ronan

2015-04-01

Building precise and up-to-date coastal DEMs is a prerequisite for accurate modeling and forecasting of hydrodynamic processes at local scale. Marine flooding, originating from tsunamis, storm surges or waves, is one of them. Some high resolution DEMs are being generated for multiple coast configurations (gulf, embayment, strait, estuary, harbor approaches, low-lying areas…) along French Atlantic and Channel coasts. This work is undertaken within the framework of the TANDEM project (Tsunamis in the Atlantic and the English ChaNnel: Definition of the Effects through numerical Modeling) (2014-2017). DEMs boundaries were defined considering the vicinity of French civil nuclear facilities, site effects considerations and potential tsunamigenic sources. Those were identified from available historical observations. Seamless integrated topographic and bathymetric coastal DEMs will be used by institutions taking part in the study to simulate expected wave height at regional and local scale on the French coasts, for a set of defined scenarii. The main tasks were (1) the development of a new capacity of production of DEM, (2) aiming at the release of high resolution and precision digital field models referred to vertical reference frameworks, that require (3) horizontal and vertical datum conversions (all source elevation data need to be transformed to a common datum), on the basis of (4) the building of (national and/or local) conversion grids of datum relationships based on known measurements. Challenges in coastal DEMs development deal with good practices throughout model development that can help minimizing uncertainties. This is particularly true as scattered elevation data with variable density, from multiple sources (national hydrographic services, state and local government agencies, research organizations and private engineering companies) and from many different types (paper fieldsheets to be digitized, single beam echo sounder, multibeam sonar, airborne laser

MIT Lincoln Laboratory Annual Report 2010

DTIC Science & Technology

2010-01-01

Research and Development Center (FFRDC) and a DoD Research and Development Laboratory. The Laboratory conducts research and development pertinent to...year, the Laboratory restruc- tured three divisions to focus research and development in areas that are increasingly important to the nation...the Director 3 Collaborations with MIT campus continue to grow, leveraging the strengths of researchers at both the Laboratory and campus. The

Calibration of DEM parameters on shear test experiments using Kriging method

NASA Astrophysics Data System (ADS)

Bednarek, Xavier; Martin, Sylvain; Ndiaye, Abibatou; Peres, Véronique; Bonnefoy, Olivier

2017-06-01

Calibration of powder mixing simulation using Discrete-Element-Method is still an issue. Achieving good agreement with experimental results is difficult because time-efficient use of DEM involves strong assumptions. This work presents a methodology to calibrate DEM parameters using Efficient Global Optimization (EGO) algorithm based on Kriging interpolation method. Classical shear test experiments are used as calibration experiments. The calibration is made on two parameters - Young modulus and friction coefficient. The determination of the minimal number of grains that has to be used is a critical step. Simulations of a too small amount of grains would indeed not represent the realistic behavior of powder when using huge amout of grains will be strongly time consuming. The optimization goal is the minimization of the objective function which is the distance between simulated and measured behaviors. The EGO algorithm uses the maximization of the Expected Improvement criterion to find next point that has to be simulated. This stochastic criterion handles with the two interpolations made by the Kriging method : prediction of the objective function and estimation of the error made. It is thus able to quantify the improvement in the minimization that new simulations at specified DEM parameters would lead to.

DEM modeling of flexible structures against granular material avalanches

NASA Astrophysics Data System (ADS)

Lambert, Stéphane; Albaba, Adel; Nicot, François; Chareyre, Bruno

2016-04-01

This article presents the numerical modeling of flexible structures intended to contain avalanches of granular and coarse material (e.g. rock slide, a debris slide). The numerical model is based on a discrete element method (YADE-Dem). The DEM modeling of both the flowing granular material and the flexible structure are detailed before presenting some results. The flowing material consists of a dry polydisperse granular material accounting for the non-sphericity of real materials. The flexible structure consists in a metallic net hanged on main cables, connected to the ground via anchors, on both sides of the channel, including dissipators. All these components were modeled as flexible beams or wires, with mechanical parameters defined from literature data. The simulation results are presented with the aim of investigating the variability of the structure response depending on different parameters related to the structure (inclination of the fence, with/without brakes, mesh size opening), but also to the channel (inclination). Results are then compared with existing recommendations in similar fields.

DEM Calibration Approach: design of experiment

NASA Astrophysics Data System (ADS)

Boikov, A. V.; Savelev, R. V.; Payor, V. A.

2018-05-01

The problem of DEM models calibration is considered in the article. It is proposed to divide models input parameters into those that require iterative calibration and those that are recommended to measure directly. A new method for model calibration based on the design of the experiment for iteratively calibrated parameters is proposed. The experiment is conducted using a specially designed stand. The results are processed with technical vision algorithms. Approximating functions are obtained and the error of the implemented software and hardware complex is estimated. The prospects of the obtained results are discussed.

Investigations of formation of quasi-static vortex-structures in granular bodies using DEM

NASA Astrophysics Data System (ADS)

Kozicki, Jan; Tejchman, Jacek

2017-06-01

The paper presents some two-dimensional simulation results of vortex-structures in cohesionless initially dense sand during quasi-static passive wall translation. The sand behaviour was simulated using the discrete element method (DEM). Sand grains were modelled by spheres with contact moments to approximately capture the irregular grain shape. In order to detect vortex-structures, the Helmholtz-Hodge decomposition of a flow displacement field from DEM calculations was used. This approach enabled us to distinguish both incompressibility and vorticity in the granular displacement field.

Visualizing impact structures using high-resolution LiDAR-derived DEMs: A case study of two structures in Missouri

USGS Publications Warehouse

Finn, Michael P.; Krizanich, Gary W.; Evans, Kevin R.; Cox, Melissa R.; Yamamoto, Kristina H.

2015-01-01

Evidence suggests that a crypto-explosive hypothesis and a meteorite impact hypothesis may be partly correct in explaining several anomalous geological features in the middle of the United States. We used a primary geographic information science (GIScience) technique of creating a digital elevation model (DEM) of two of these features that occur in Missouri. The DEMs were derived from airborne light detection and ranging, or LiDAR. Using these DEMs, we characterized the Crooked Creek structure in southern Crawford County and the Weaubleau structure in southeastern St. Clair County, Missouri. The mensuration and study of exposed and buried impact craters implies that the craters may have intrinsic dimensions which could only be produced by collision. The results show elevations varying between 276 and 348 m for Crooked Creek and between 220 and 290 m for Weaubleau structure. These new high- resolution DEMs are accurate enough to allow for precise measurements and better interpretations of geological structures, particularly jointing in the carbonate rocks, and they show greater definition of the central uplift area in the Weaubleau structure than publicly available DEMs.

Vertical Accuracy Assessment of 30-M Resolution Alos, Aster, and Srtm Global Dems Over Northeastern Mindanao, Philippines

NASA Astrophysics Data System (ADS)

Santillan, J. R.; Makinano-Santillan, M.

2016-06-01

The ALOS World 3D - 30 m (AW3D30), ASTER Global DEM Version 2 (GDEM2), and SRTM-30 m are Digital Elevation Models (DEMs) that have been made available to the general public free of charge. An important feature of these DEMs is their unprecedented horizontal resolution of 30-m and almost global coverage. The very recent release of these DEMs, particularly AW3D30 and SRTM- 30 m, calls for opportunities for the conduct of localized assessment of the DEM's quality and accuracy to verify their suitability for a wide range of applications in hydrology, geomorphology, archaelogy, and many others. In this study, we conducted a vertical accuracy assessment of these DEMs by comparing the elevation of 274 control points scattered over various sites in northeastern Mindanao, Philippines. The elevations of these control points (referred to the Mean Sea Level, MSL) were obtained through 3rd order differential levelling using a high precision digital level, and their horizontal positions measured using a global positioning system (GPS) receiver. These control points are representative of five (5) land-cover classes namely brushland (45 points), built-up (32), cultivated areas (97), dense vegetation (74), and grassland (26). Results showed that AW3D30 has the lowest Root Mean Square Error (RMSE) of 5.68 m, followed by SRTM-30 m (RMSE = 8.28 m), and ASTER GDEM2 (RMSE = 11.98 m). While all the three DEMs overestimated the true ground elevations, the mean and standard deviations of the differences in elevations were found to be lower in AW3D30 compared to SRTM-30 m and ASTER GDEM2. The superiority of AW3D30 over the other two DEMS was also found to be consistent even under different landcover types, with AW3D30's RMSEs ranging from 4.29 m (built-up) to 6.75 m (dense vegetation). For SRTM-30 m, the RMSE ranges from 5.91 m (built-up) to 10.42 m (brushland); for ASTER

High-resolution digital elevation models from single-pass TanDEM-X interferometry over mountainous regions: A case study of Inylchek Glacier, Central Asia

NASA Astrophysics Data System (ADS)

Neelmeijer, Julia; Motagh, Mahdi; Bookhagen, Bodo

2017-08-01

This study demonstrates the potential of using single-pass TanDEM-X (TDX) radar imagery to analyse inter- and intra-annual glacier changes in mountainous terrain. Based on SAR images acquired in February 2012, March 2013 and November 2013 over the Inylchek Glacier, Kyrgyzstan, we discuss in detail the processing steps required to generate three reliable digital elevation models (DEMs) with a spatial resolution of 10 m that can be used for glacial mass balance studies. We describe the interferometric processing steps and the influence of a priori elevation information that is required to model long-wavelength topographic effects. We also focus on DEM alignment to allow optimal DEM comparisons and on the effects of radar signal penetration on ice and snow surface elevations. We finally compare glacier elevation changes between the three TDX DEMs and the C-band shuttle radar topography mission (SRTM) DEM from February 2000. We introduce a new approach for glacier elevation change calculations that depends on the elevation and slope of the terrain. We highlight the superior quality of the TDX DEMs compared to the SRTM DEM, describe remaining DEM uncertainties and discuss the limitations that arise due to the side-looking nature of the radar sensor.

Netzformen und VDE-Bestimmungen

NASA Astrophysics Data System (ADS)

Bernstein, Herbert

Der Verband Deutscher Elektrotechniker (VDE) hat eine Reihe von Vorschriften ausgearbeitet, die dem Schutz von Leben und Sachen beim Umgang mit elektrischer Energie dienen. Besonders wichtig sind die in den VDE-Bestimmungen 0100 und 0411 festgelegten Vorschriften.

Biotechnology Process Engineering Center at MIT - Overview

Science.gov Websites

ADVISORY BOARD Under an academic paradigm set forth by the National Science Foundation for National Engineering Research Centers, BPEC exists as a partnership with industry. Regular two-way information flow sabbaticals at MIT and student internships at our industrial partners. We have selected an elite group of

Rockslide and Impulse Wave Modelling in the Vajont Reservoir by DEM-CFD Analyses

NASA Astrophysics Data System (ADS)

Zhao, T.; Utili, S.; Crosta, G. B.

2016-06-01

This paper investigates the generation of hydrodynamic water waves due to rockslides plunging into a water reservoir. Quasi-3D DEM analyses in plane strain by a coupled DEM-CFD code are adopted to simulate the rockslide from its onset to the impact with the still water and the subsequent generation of the wave. The employed numerical tools and upscaling of hydraulic properties allow predicting a physical response in broad agreement with the observations notwithstanding the assumptions and characteristics of the adopted methods. The results obtained by the DEM-CFD coupled approach are compared to those published in the literature and those presented by Crosta et al. (Landslide spreading, impulse waves and modelling of the Vajont rockslide. Rock mechanics, 2014) in a companion paper obtained through an ALE-FEM method. Analyses performed along two cross sections are representative of the limit conditions of the eastern and western slope sectors. The max rockslide average velocity and the water wave velocity reach ca. 22 and 20 m/s, respectively. The maximum computed run up amounts to ca. 120 and 170 m for the eastern and western lobe cross sections, respectively. These values are reasonably similar to those recorded during the event (i.e. ca. 130 and 190 m, respectively). Therefore, the overall study lays out a possible DEM-CFD framework for the modelling of the generation of the hydrodynamic wave due to the impact of a rapid moving rockslide or rock-debris avalanche.

Extraction and Validation of Geomorphological Features from EU-DEM in The Vicinity of the Mygdonia Basin, Northern Greece

NASA Astrophysics Data System (ADS)

Mouratidis, Antonios; Karadimou, Georgia; Ampatzidis, Dimitrios

2017-12-01

The European Union Digital Elevation Model (EU-DEM) is a relatively new, hybrid elevation product, principally based on SRTM DEM and ASTER GDEM data, but also on publically available Russian topographic maps for regions north of 60° N. More specifically, EU-DEM is a Digital Surface Model (DSM) over Europe from the Global Monitoring for Environment and Security (GMES) Reference Data Access (RDA) project - a realisation of the Copernicus (former GMES) programme, managed by the European Commission/DG Enterprise and Industry. Even if EU-DEM is indeed more reliable in terms of elevation accuracy than its constituents, it ought to be noted that it is not representative of the original elevation measurements, but is rather a secondary (mathematical) product. Therefore, for specific applications, such as those of geomorphological interest, artefacts may be induced. To this end, the purpose of this paper is to investigate the performance of EU-DEM for geomorphological applications and compare it against other available datasets, i.e. topographic maps and (almost) global DEMs such as SRTM, ASTER-GDEM and WorldDEM™. This initial investigation is carried out in Central Macedonia, Northern Greece, in the vicinity of the Mygdonia basin, which corresponds to an area of particular interest for several geoscience applications. This area has also been serving as a test site for the systematic validation of DEMs for more than a decade. Consequently, extensive elevation datasets and experience have been accumulated over the years, rendering the evaluation of new elevation products a coherent and useful exercise on a local to regional scale. In this context, relief classification, drainage basin delineation, slope and slope aspect, as well as extraction and classification of drainage network are performed and validated among the aforementioned elevation sources. The achieved results focus on qualitative and quantitative aspects of automatic geomorphological feature extraction from

Studies of the hadronic mass spectrum from semileptonic decays of B mesons

NASA Astrophysics Data System (ADS)

Roberts, Scott Eric

1997-09-01

This dissertation describes a study of inclusive semileptonic decays of B mesons: B/to Xc/ell/nu and B/to Xu/ell/nu. Here, Xc is a hadronic system containing a charm quark, and Xu is a hadronic system not containing one. The term 'inclusive' indicates summation over all possible hadronic systems Xc and Xu. The study used B/bar B pairs produced in e+e/sp- annihilations at the Υ(4S) resonance, data collected with the CLEO-II detector at the Cornell Electron Storage Ring. A direct measurement of the momentum of the charged leptons (e and /mu), and an inferred measurement of the neutrino's momentum in events, makes possible an approximate calculation of MX2, the mass- squared of the hadronic system X. From this distribution we find, for b/to c/ell/nu decays with a lepton above 1.5 GeV/c,/eqalign[/langle M/it X2-/bar m/it D2/rangle& = 0.286/pm0.023/pm 0.080/ GeV2/cr <(M/it X2-/bar m/it D2)2/rangle& =0.911/pm0.066/pm0.309/ GeV4./cr]These measurements imply values for the Heavy Quark Effective Theory parameters, ¯Lambda and λ1, of/eqalign[/bar/Lambda& =0.351/pm0.019/pm0.088/pm0.037/ GeV/cr λ1& =[-]0.152/pm0.014/pm0.063/pm0.026/ GeV2./cr] By fitting the approximate MX2 distribution in events with leptons of momenta greater than 2.0 GeV/c, we find [/cal B](b/to u/ell/nu)(2.0[-]2.7/ [ GeV/c]) = (1.12/pm0.20/pm0.34)×10-3,which implies a value of 0.069/pm0.006/pm0.011/pm0.027 for the ratio of CKM matrix elements /vert[Vub/over Vcb]/vert.

Prospective pilot trial of PerMIT versus standard anticoagulation service management of patients initiating oral anticoagulation.

PubMed

Borgman, Mark P; Pendleton, Robert C; McMillin, Gwendolyn A; Reynolds, Kristen K; Vazquez, Sara; Freeman, Andrew; Wilson, Andrew; Valdes, Roland; Linder, Mark W

2012-09-01

We performed a randomised pilot trial of PerMIT, a novel decision support tool for genotype-based warfarin initiation and maintenance dosing, to assess its efficacy for improving warfarin management. We prospectively studied 26 subjects to compare PerMIT-guided management with routine anticoagulation service management. CYP2C9 and VKORC1 genotype results for 13 subjects randomly assigned to the PerMIT arm were recorded within 24 hours of enrolment. To aid in INR interpretation, PerMIT calculates estimated loading and maintenance doses based on a patient's genetic and clinical characteristics and displays calculated S-warfarin plasma concentrations based on planned or administered dosages. In comparison to control subjects, patients in the PerMIT study arm demonstrated a 3.6-day decrease in the time to reach a stabilised INR within the target therapeutic range (4.7 vs. 8.3 days, p = 0.015); a 12.8% increase in time spent within the therapeutic interval over the first 25 days of therapy (64.3% vs. 55.3%, p = 0.180); and a 32.9% decrease in the frequency of warfarin dose adjustments per INR measurement (38.3% vs. 57.1%, p = 0.007). Serial measurements of plasma S-warfarin concentrations were also obtained to prospectively evaluate the accuracy of the pharmacokinetic model during induction therapy. The PerMIT S-warfarin plasma concentration model estimated 62.8% of concentrations within 0.15 mg/l. These pilot data suggest that the PerMIT method and its incorporation of genotype/phenotype information may help practitioners increase the safety, efficacy, and efficiency of warfarin therapeutic management.

a Hadoop-Based Algorithm of Generating dem Grid from Point Cloud Data

NASA Astrophysics Data System (ADS)

Jian, X.; Xiao, X.; Chengfang, H.; Zhizhong, Z.; Zhaohui, W.; Dengzhong, Z.

2015-04-01

Airborne LiDAR technology has proven to be the most powerful tools to obtain high-density, high-accuracy and significantly detailed surface information of terrain and surface objects within a short time, and from which the Digital Elevation Model of high quality can be extracted. Point cloud data generated from the pre-processed data should be classified by segmentation algorithms, so as to differ the terrain points from disorganized points, then followed by a procedure of interpolating the selected points to turn points into DEM data. The whole procedure takes a long time and huge computing resource due to high-density, that is concentrated on by a number of researches. Hadoop is a distributed system infrastructure developed by the Apache Foundation, which contains a highly fault-tolerant distributed file system (HDFS) with high transmission rate and a parallel programming model (Map/Reduce). Such a framework is appropriate for DEM generation algorithms to improve efficiency. Point cloud data of Dongting Lake acquired by Riegl LMS-Q680i laser scanner was utilized as the original data to generate DEM by a Hadoop-based algorithms implemented in Linux, then followed by another traditional procedure programmed by C++ as the comparative experiment. Then the algorithm's efficiency, coding complexity, and performance-cost ratio were discussed for the comparison. The results demonstrate that the algorithm's speed depends on size of point set and density of DEM grid, and the non-Hadoop implementation can achieve a high performance when memory is big enough, but the multiple Hadoop implementation can achieve a higher performance-cost ratio, while point set is of vast quantities on the other hand.

DEM time series of an agricultural watershed

NASA Astrophysics Data System (ADS)

Pineux, Nathalie; Lisein, Jonathan; Swerts, Gilles; Degré, Aurore

2014-05-01

In agricultural landscape soil surface evolves notably due to erosion and deposition phenomenon. Even if most of the field data come from plot scale studies, the watershed scale seems to be more appropriate to understand them. Currently, small unmanned aircraft systems and images treatments are improving. In this way, 3D models are built from multiple covering shots. When techniques for large areas would be to expensive for a watershed level study or techniques for small areas would be too time consumer, the unmanned aerial system seems to be a promising solution to quantify the erosion and deposition patterns. The increasing technical improvements in this growth field allow us to obtain a really good quality of data and a very high spatial resolution with a high Z accuracy. In the center of Belgium, we equipped an agricultural watershed of 124 ha. For three years (2011-2013), we have been monitoring weather (including rainfall erosivity using a spectropluviograph), discharge at three different locations, sediment in runoff water, and watershed microtopography through unmanned airborne imagery (Gatewing X100). We also collected all available historical data to try to capture the "long-term" changes in watershed morphology during the last decades: old topography maps, soil historical descriptions, etc. An erosion model (LANDSOIL) is also used to assess the evolution of the relief. Short-term evolution of the surface are now observed through flights done at 200m height. The pictures are taken with a side overlap equal to 80%. To precisely georeference the DEM produced, ground control points are placed on the study site and surveyed using a Leica GPS1200 (accuracy of 1cm for x and y coordinates and 1.5cm for the z coordinate). Flights are done each year in December to have an as bare as possible ground surface. Specific treatments are developed to counteract vegetation effect because it is know as key sources of error in the DEM produced by small unmanned aircraft

Biotechnology Process Engineering Center at MIT Home

Science.gov Websites

has provided a focal point for biotechnology research and education at MIT. Prominent examples include to be one of the most crucial interdisciplinary research centers connected to BE; a significant and providing support for research and education at the nexus of biology, engineering, and materials

MFIX-DEM Phi: Performance and Capability Improvements Towards Industrial Grade Open-source DEM Framework with Integrated Uncertainty Quantification

DOE Office of Scientific and Technical Information (OSTI.GOV)

GEL, Aytekin; Jiao, Yang; Emady, Heather

Two major challenges hinder the effective use and adoption of multiphase computational fluid dynamics tools by the industry. The first is the need for significant computational resources, which is inversely proportional to the accuracy of solutions due to computational intensity of the algorithms. The second barrier is assessing the prediction credibility and confidence in the simulation results. In this project, a multi-tiered approach has been proposed under four broad activities to overcome these challenges while addressing all of the objectives outlined in FOA-0001238 through Phases 1 and 2 of the project. The present report consists of the results for onlymore » Phase 1, which was the funded performance period. From the start the project, all of the objectives outlined in FOA were addressed through four major activity tasks in an integrated and balanced fashion to improve adoption of MFIX suite of solvers for industrial use. The first task aimed to improve the performance of MFIX-DEM specifically targeting to acquire the peak performance on Intel Xeon and Xeon Phi based systems, which are expected to be one of the primary high-performance computing platforms both affordable and available for the industrial users in the next two to five years. However, due to a number of changes in course of the project, the scope of the performance improvements related task was significantly reduced to avoid duplicate work. Hence, more emphasis was placed on the other three tasks as discussed below.The second task aimed at physical modeling enhancements through implementation of polydispersity capability and validation of heat transfer models in MFIX. An extended verification and validation (V&V) study was performed for the new polydispersity feature implemented in MFIX-DEM both for granular and coupled gas-solid flows. The features of the polydispersity capability and results for an industrially relevant problem were disseminated through journal papers (one published and

DynaMIT: the dynamic motif integration toolkit

PubMed Central

Dassi, Erik; Quattrone, Alessandro

2016-01-01

De-novo motif search is a frequently applied bioinformatics procedure to identify and prioritize recurrent elements in sequences sets for biological investigation, such as the ones derived from high-throughput differential expression experiments. Several algorithms have been developed to perform motif search, employing widely different approaches and often giving divergent results. In order to maximize the power of these investigations and ultimately be able to draft solid biological hypotheses, there is the need for applying multiple tools on the same sequences and merge the obtained results. However, motif reporting formats and statistical evaluation methods currently make such an integration task difficult to perform and mostly restricted to specific scenarios. We thus introduce here the Dynamic Motif Integration Toolkit (DynaMIT), an extremely flexible platform allowing to identify motifs employing multiple algorithms, integrate them by means of a user-selected strategy and visualize results in several ways; furthermore, the platform is user-extendible in all its aspects. DynaMIT is freely available at http://cibioltg.bitbucket.org. PMID:26253738

MIT Lincoln Laboratory Annual Report 2009

DTIC Science & Technology

2009-01-01

unclassified c. THIS PAGE unclassified Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 MIt lincoln laboratory Massachusetts Institute...Climate-change monitoring that will be conducted by assessing the utility of using very-long-wave infrared radiation for space-based sensing and by... radiation to detect trace explosives on a person’s hair were investigated. An ultrasensitive THz receiver leverages mature technology at the near-infrared

Hydrology, secondary growth, and elevation accuracy in two preliminary Amazon Basin SRTM DEMs

NASA Astrophysics Data System (ADS)

Alsdorf, D.; Hess, L.; Sheng, Y.; Souza, C.; Pavelsky, T.; Melack, J.; Dunne, T.; Hendricks, G.; Ballantine, A.; Holmes, K.

2003-04-01

Two preliminary Shuttle Radar Topography Mission digital elevation models (SRTM DEMs) of Manaus (1S to 5S and 59W to 63W) and Rondonia (9S to 12S and 61W to 64W) were received from the "PI Processor" at NASA JPL. We compared the Manaus DEM (C-band) with a previously constructed Cabaliana floodplain classification based on Global RainForest Mapping (GRFM) JERS-1 SAR data (L-band) and determined that habitats of open water, bare ground, and flooded shrub contained the lowest elevations; macrophyte and non-flooded shrub habitats are marked by intermediate elevations; and the highest elevations are found within flooded and non-flooded forest. Although the water surface typically produces specular reflections, double-bounce travel paths result from dead, leafless trees found across the Balbina reservoir near Manaus. There (i.e., in Balbina) the water surface is marked by pixel-to-pixel height changes of generally 0 to 1 m and changes across a ˜100 km transect rarely exceed 3 m. Reported SRTM errors throughout the transect range from 1 to 2 m with some errors up to 5 m. The smooth Balbina surface contrasts with the wind-roughened Amazon River surface where SRTM height variations easily range from 1 to 10 m (reported errors often exceed 5 m). Deforestation and subsequent regrowth in the Rondonia DEM is remarkably clear. Our colleagues used a 20 year sequence of Landsat TM/MSS classified imagery to delineate areas in various stages of secondary growth and we find a general trend of increasing vegetation height with increasing age. Flow path networks derived from the Cabaliana floodplain DEM are in general agreement with networks previously extracted from the GRFM mosaics; however, watershed boundaries differ. We have also developed an algorithm for extracting channel widths, which is presently being applied to the DEM and classified imagery to determine morphological variations between reaches.

BOREAS HYP-8 DEM Data Over The NSA-MSA and SSA-MSA in The AEAC Projection

NASA Technical Reports Server (NTRS)

Knapp, David E.; Hall, Forrest G. (Editor); Wang, Xue-Wen; Band, L. E.; Smith, David E. (Technical Monitor)

2000-01-01

These data were derived from the original Digital Elevation Models (DEMs) produced by the Boreal Ecosystem-Atmosphere Study (BOREAS) Hydrology (HYD)-8 team. The original DEMs were in the Universal Transverse Mercator (UTM) projection, while this product is projected in the Albers Equal-Area Conic (AEAC) projection. The pixel size of the data is 100 meters, which is appropriate for the 1:50,000-scale contours from which the DEMs were made. The original data were compiled from information available in the 1970s and 1980s. This data set covers the two Modeling Sub-Areas (MSAs) that are contained within the Southern Study Area (SSA) and the Northern Study Area (NSA). The data are stored in binary, image format files. The DEM data over the NSA-MSA and SSA-MSA in the AEAC projection are available from the Earth Observing System Data and Information System (EOSDIS) Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC). The data files are available on a CD-ROM (see document number 20010000884).

Integration of SAR and DEM data: Geometrical considerations

NASA Technical Reports Server (NTRS)

Kropatsch, Walter G.

1991-01-01

General principles for integrating data from different sources are derived from the experience of registration of SAR images with digital elevation models (DEM) data. The integration consists of establishing geometrical relations between the data sets that allow us to accumulate information from both data sets for any given object point (e.g., elevation, slope, backscatter of ground cover, etc.). Since the geometries of the two data are completely different they cannot be compared on a pixel by pixel basis. The presented approach detects instances of higher level features in both data sets independently and performs the matching at the high level. Besides the efficiency of this general strategy it further allows the integration of additional knowledge sources: world knowledge and sensor characteristics are also useful sources of information. The SAR features layover and shadow can be detected easily in SAR images. An analytical method to find such regions also in a DEM needs in addition the parameters of the flight path of the SAR sensor and the range projection model. The generation of the SAR layover and shadow maps is summarized and new extensions to this method are proposed.

Craniota, Wirbel- oder Schädeltiere

NASA Astrophysics Data System (ADS)

Schultze, Hans-Peter

Zu den Craniota zählen alle Chordatiere, die eine dreiteilige Regionalisierung des Körpers in Kopf, Rumpf und Schwanz aufweisen. Der Kopf umfasst (1) das Neurocranium mit Gehirn und komplexen Sinnesorganen zur Wahrnehmung der Umgebung, (2) das Viscerocranium zur Nahrungsaufnahme und zur Ventilation der Kiemen bei den primär wasserlebenden Craniota und (3) das Dermatocranium (S. 38). Letzteres entsteht durch Verknöcherungen im Bindegewebe des Integuments, es dient dem Schutz des Kopfes und trägt im Mundbreich die Zähne. Zusammen bilden die drei Skelettstrukturen die funktionelle Einheit Schädel (Cranium). Außer der (somatischen) Rumpfmuskulatur und dem Axialskelett liegen im Rumpf Kreislauf-, Atmungs-, Verdauungs-, Exkretions- und Fortpflanzungsorgane. Der Schwanz, der Abschnitt hinter der Afteröffnung, die das Ende der Leibeshöhle markiert, dient mit Muskeln und Schwanzflosse der Fortbewegung.

Reanalysis of the DEMS Nested Case-Control Study of Lung Cancer and Diesel Exhaust: Suitability for Quantitative Risk Assessment

PubMed Central

Crump, Kenny S; Van Landingham, Cynthia; Moolgavkar, Suresh H; McClellan, Roger

2015-01-01

The International Agency for Research on Cancer (IARC) in 2012 upgraded its hazard characterization of diesel engine exhaust (DEE) to “carcinogenic to humans.” The Diesel Exhaust in Miners Study (DEMS) cohort and nested case-control studies of lung cancer mortality in eight U.S. nonmetal mines were influential in IARC’s determination. We conducted a reanalysis of the DEMS case-control data to evaluate its suitability for quantitative risk assessment (QRA). Our reanalysis used conditional logistic regression and adjusted for cigarette smoking in a manner similar to the original DEMS analysis. However, we included additional estimates of DEE exposure and adjustment for radon exposure. In addition to applying three DEE exposure estimates developed by DEMS, we applied six alternative estimates. Without adjusting for radon, our results were similar to those in the original DEMS analysis: all but one of the nine DEE exposure estimates showed evidence of an association between DEE exposure and lung cancer mortality, with trend slopes differing only by about a factor of two. When exposure to radon was adjusted, the evidence for a DEE effect was greatly diminished, but was still present in some analyses that utilized the three original DEMS DEE exposure estimates. A DEE effect was not observed when the six alternative DEE exposure estimates were utilized and radon was adjusted. No consistent evidence of a DEE effect was found among miners who worked only underground. This article highlights some issues that should be addressed in any use of the DEMS data in developing a QRA for DEE. PMID:25857246

Fusion of space-borne multi-baseline and multi-frequency interferometric results based on extended Kalman filter to generate high quality DEMs

NASA Astrophysics Data System (ADS)

Zhang, Xiaojie; Zeng, Qiming; Jiao, Jian; Zhang, Jingfa

2016-01-01

Repeat-pass Interferometric Synthetic Aperture Radar (InSAR) is a technique that can be used to generate DEMs. But the accuracy of InSAR is greatly limited by geometrical distortions, atmospheric effect, and decorrelations, particularly in mountainous areas, such as western China where no high quality DEM has so far been accomplished. Since each of InSAR DEMs generated using data of different frequencies and baselines has their own advantages and disadvantages, it is therefore very potential to overcome some of the limitations of InSAR by fusing Multi-baseline and Multi-frequency Interferometric Results (MMIRs). This paper proposed a fusion method based on Extended Kalman Filter (EKF), which takes the InSAR-derived DEMs as states in prediction step and the flattened interferograms as observations in control step to generate the final fused DEM. Before the fusion, detection of layover and shadow regions, low-coherence regions and regions with large height error is carried out because MMIRs in these regions are believed to be unreliable and thereafter are excluded. The whole processing flow is tested with TerraSAR-X and Envisat ASAR datasets. Finally, the fused DEM is validated with ASTER GDEM and national standard DEM of China. The results demonstrate that the proposed method is effective even in low coherence areas.

Identification of potential rockfall source areas at a regional scale using a DEM-based geomorphometric analysis

NASA Astrophysics Data System (ADS)

Loye, A.; Jaboyedoff, M.; Pedrazzini, A.

2009-10-01

The availability of high resolution Digital Elevation Models (DEM) at a regional scale enables the analysis of topography with high levels of detail. Hence, a DEM-based geomorphometric approach becomes more accurate for detecting potential rockfall sources. Potential rockfall source areas are identified according to the slope angle distribution deduced from high resolution DEM crossed with other information extracted from geological and topographic maps in GIS format. The slope angle distribution can be decomposed in several Gaussian distributions that can be considered as characteristic of morphological units: rock cliffs, steep slopes, footslopes and plains. A terrain is considered as potential rockfall sources when their slope angles lie over an angle threshold, which is defined where the Gaussian distribution of the morphological unit "Rock cliffs" become dominant over the one of "Steep slopes". In addition to this analysis, the cliff outcrops indicated by the topographic maps were added. They contain however "flat areas", so that only the slope angles values above the mode of the Gaussian distribution of the morphological unit "Steep slopes" were considered. An application of this method is presented over the entire Canton of Vaud (3200 km2), Switzerland. The results were compared with rockfall sources observed on the field and orthophotos analysis in order to validate the method. Finally, the influence of the cell size of the DEM is inspected by applying the methodology over six different DEM resolutions.

The knockdown of OsVIT2 and MIT affects iron localization in rice seed.

PubMed

Bashir, Khurram; Takahashi, Ryuichi; Akhtar, Shamim; Ishimaru, Yasuhiro; Nakanishi, Hiromi; Nishizawa, Naoko K

2013-11-20

The mechanism of iron (Fe) uptake in plants has been extensively characterized, but little is known about how Fe transport to different subcellular compartments affects Fe localization in rice seed. Here, we discuss the characterization of a rice vacuolar Fe transporter 2 (OsVIT2) T-DNA insertion line (osvit2) and report that the knockdown of OsVIT2 and mitochondrial Fe transporter (MIT) expression affects seed Fe localization. osvit2 plants accumulated less Fe in their shoots when grown under normal or excess Fe conditions, while the accumulation of Fe was comparable to that in wild-type (WT) plants under Fe-deficient conditions. The accumulation of zinc, copper, and manganese also changed significantly in the shoots of osvit2 plants. The growth of osvit2 plants was also slow compared to that of WT plants. The concentration of Fe increased in osvit2 polished seeds. Previously, we reported that the expression of OsVIT2 was higher in MIT knockdown (mit-2) plants, and in this study, the accumulation of Fe in mit-2 seeds decreased significantly. These results suggest that vacuolar Fe trafficking is important for plant Fe homeostasis and distribution, especially in plants grown in the presence of excess Fe. Moreover, changes in the expression of OsVIT2 and MIT affect the concentration and localization of metals in brown rice as well as in polished rice seeds.

MitProNet: A Knowledgebase and Analysis Platform of Proteome, Interactome and Diseases for Mammalian Mitochondria

PubMed Central

Mao, Song; Chai, Xiaoqiang; Hu, Yuling; Hou, Xugang; Tang, Yiheng; Bi, Cheng; Li, Xiao

2014-01-01

Mitochondrion plays a central role in diverse biological processes in most eukaryotes, and its dysfunctions are critically involved in a large number of diseases and the aging process. A systematic identification of mitochondrial proteomes and characterization of functional linkages among mitochondrial proteins are fundamental in understanding the mechanisms underlying biological functions and human diseases associated with mitochondria. Here we present a database MitProNet which provides a comprehensive knowledgebase for mitochondrial proteome, interactome and human diseases. First an inventory of mammalian mitochondrial proteins was compiled by widely collecting proteomic datasets, and the proteins were classified by machine learning to achieve a high-confidence list of mitochondrial proteins. The current version of MitProNet covers 1124 high-confidence proteins, and the remainders were further classified as middle- or low-confidence. An organelle-specific network of functional linkages among mitochondrial proteins was then generated by integrating genomic features encoded by a wide range of datasets including genomic context, gene expression profiles, protein-protein interactions, functional similarity and metabolic pathways. The functional-linkage network should be a valuable resource for the study of biological functions of mitochondrial proteins and human mitochondrial diseases. Furthermore, we utilized the network to predict candidate genes for mitochondrial diseases using prioritization algorithms. All proteins, functional linkages and disease candidate genes in MitProNet were annotated according to the information collected from their original sources including GO, GEO, OMIM, KEGG, MIPS, HPRD and so on. MitProNet features a user-friendly graphic visualization interface to present functional analysis of linkage networks. As an up-to-date database and analysis platform, MitProNet should be particularly helpful in comprehensive studies of complicated

A METABOLIC SIGNATURE FOR LONG-LIFE IN THE C. ELEGANS MIT MUTANTS

PubMed Central

Butler, Jeffrey A.; Mishur, Robert J.; Bhaskaran, Shylesh; Rea, Shane L.

2012-01-01

SUMMARY Mit mutations that disrupt function of the mitochondrial electron transport chain can, inexplicably, prolong Caenorhabditis elegans lifespan. In this study we use a metabolomics approach to identify an ensemble of mitochondrial-derived α-ketoacids and α-hydroxyacids that are produced by long-lived Mit mutants but not by other long-lived mutants or by short-lived mitochondrial mutants. We show that accumulation of these compounds is dependent upon concerted inhibition of three α-ketoacid dehydrogenases that share dihydrolipoamide dehydrogenase (DLD) as a common subunit, a protein previously linked in humans with increased risk of Alzheimer’s disease. When the expression of DLD in wild type animals was reduced using RNA interference we observed an unprecedented effect on lifespan - as RNAi dosage was increased lifespan was significantly shortened but, at higher doses, it was significantly lengthened, suggesting DLD plays a unique role in modulating length of life. Our findings provide novel insight into the origin of the Mit phenotype. PMID:23173729

All you need is shape: Predicting shear banding in sand with LS-DEM

NASA Astrophysics Data System (ADS)

Kawamoto, Reid; Andò, Edward; Viggiani, Gioacchino; Andrade, José E.

2018-02-01

This paper presents discrete element method (DEM) simulations with experimental comparisons at multiple length scales-underscoring the crucial role of particle shape. The simulations build on technological advances in the DEM furnished by level sets (LS-DEM), which enable the mathematical representation of the surface of arbitrarily-shaped particles such as grains of sand. We show that this ability to model shape enables unprecedented capture of the mechanics of granular materials across scales ranging from macroscopic behavior to local behavior to particle behavior. Specifically, the model is able to predict the onset and evolution of shear banding in sands, replicating the most advanced high-fidelity experiments in triaxial compression equipped with sequential X-ray tomography imaging. We present comparisons of the model and experiment at an unprecedented level of quantitative agreement-building a one-to-one model where every particle in the more than 53,000-particle array has its own avatar or numerical twin. Furthermore, the boundary conditions of the experiment are faithfully captured by modeling the membrane effect as well as the platen displacement and tilting. The results show a computational tool that can give insight into the physics and mechanics of granular materials undergoing shear deformation and failure, with computational times comparable to those of the experiment. One quantitative measure that is extracted from the LS-DEM simulations that is currently not available experimentally is the evolution of three dimensional force chains inside and outside of the shear band. We show that the rotations on the force chains are correlated to the rotations in stress principal directions.

Combined SDO/AIA, Hinode/XRT and FOXSI-2 microflare observations - DEM analysis and energetics

NASA Astrophysics Data System (ADS)

Panchapakesan, S. A.; Glesener, L.; Vievering, J. T.; Ryan, D.; Christe, S.; Inglis, A. R.; Buitrago-Casas, J. C.; Musset, S.; Krucker, S.

2017-12-01

The Focusing Optics X-ray Solar Imager (FOXSI) sounding rocket makes directimaging and spectral observation of the Sun in hard X-rays (HXRs) using highlysensitive focusing HXR optics. The second flight of FOXSI was launchedsuccessfully on 11 December 2014 and observed significant HXR emissions duringmicroflares. Some of these flares showed heating up to severalmillion Kelvin and were visible in the Extreme Ultraviolet (EUV) with the AtmosphericImaging Assembly (SDO/AIA). Spectral observations from FOXSI suggest emission upto 10-12 MK. We utilize SDO/AIA EUV, Hinode/XRT soft X-ray, and FOXSI-2 highenergy X-ray observations to derive the differential emission measure (DEM) ofthe microflares. The AIA and XRT observations provide broad temperaturecoverage but are poorly constrained at the hotter end. We therefore use FOXSI-2to better determine the high temperature component, thus producing a moreconstrained DEM than is possible with typically available observations. We usethis more highly constrained DEM to investigate the energetics of the observedmicroflares.

A biopsychosocial vignette for case conceptualization in dementia (VIG-Dem): development and pilot study.

PubMed

Spector, Aimee; Hebditch, Molly; Stoner, Charlotte R; Gibbor, Luke

2016-09-01

The ability to identify biological, social, and psychological issues for people with dementia is an important skill for healthcare professionals. Therefore, valid and reliable measures are needed to assess this ability. This study involves the development of a vignette style measure to capture the extent to which health professionals use "Biopsychosocial" thinking in dementia care (VIG-Dem), based on the framework of the model developed by Spector and Orrell (2010). The development process consisted of Phase 1: Developing and refining the vignettes; Phase 2: Field testing (N = 9), and Phase 3: A pilot study to assess reliability and validity (N = 131). The VIG-Dem, consisting of two vignettes with open-ended questions and a standardized scoring scheme, was developed. Evidence for the good inter-rater reliability, convergent validity, and test-retest reliability were established. The VIG-Dem has good psychometric properties and may provide a useful tool in dementia care research and practice.

Der Einfluss der Digitalisierung auf die Organisation eines Unternehmens

NASA Astrophysics Data System (ADS)

Walter, Wolfram M.

Die Digitalisierung schreitet mit großen Schritten voran. Dies wirkt sich nicht nur auf die Gesellschaft im Grundsatz, sondern auch auf das Verhalten der Kunden aus. Neue Kommunikationswege beschleunigen die Interaktion zwischen Unternehmen und Verbraucher. Im Vergleich mit großen Internetfirmen werden etablierte Dienstleistungsunternehmen - vom Energieversorger bis zu Versicherungen - stark unter Druck gesetzt, sich noch intensiver mit dem Kundenservice auseinanderzusetzen. Dies wird nur möglich sein, wenn sich die Organisationen entsprechend positionieren und sich frühzeitig auf die Veränderungen einstellen. Hieraus ergeben sich mehr Chancen als Risiken, zumal es nicht nur neue Prozesse, sondern auch neue Berufsbilder geben wird.

Detailed geomorphological mapping from high resolution DEM data (LiDAR, TanDEM-X): two case studies from Germany and SE Tibet

NASA Astrophysics Data System (ADS)

Loibl, D.

2012-04-01

Two major obstacles are hampering the production of high resolution geomorphological maps: the complexity of the subject that should be depicted and the enormous efforts necessary to obtain data by field work. The first factor prevented the establishment of a generally accepted map legend; the second hampered efforts to collect comprehensive sets of geomorphological data. This left geomorphologists to produce applied maps, focusing on very few layers of information and often not sticking to any of the numerous standards proposed in the second half of the 20th century. Technological progress of the recent years, especially in the fields of digital elevation models, GIS environments, and computational hardware, today offers promising opportunities to overcome the obstacles and to produce detailed geomorphological maps even for remote or inhospitable regions. The feasibility of detailed geomorphological mapping from two new sets of digital elevation data, the 1 m LiDAR DTM provided by Germany's State Surveying Authority and the upcoming TanDEM-X DEM, has been evaluated in two case studies from a low mountain range in Germany and a high mountain range in SE Tibet. The results indicate that most layers of information of classical geomorphological maps (e.g. the German GMK) can be extracted from this data at appropriate scales but that significant differences occur concerning the quality and the grades of certainty of key contents. Generally, an enhancement of the geomorphographical, especially the geomorphometrical, and a weakening of geomorphogenetical contents was observed. From these findings, theoretical, methodological, and cartographical remarks on detailed geomorphological mapping from DEM data in GIS environments were educed. As GIS environments decouple data and design and enable the geomorphologist to choose information layer combinations freely to fit research topics, a general purpose legend becomes obsolete. Yet, a unified data structure is demanded to

3D DEM analyses of the 1963 Vajont rock slide

NASA Astrophysics Data System (ADS)

Boon, Chia Weng; Houlsby, Guy; Utili, Stefano

2013-04-01

The 1963 Vajont rock slide has been modelled using the distinct element method (DEM). The open-source DEM code, YADE (Kozicki & Donzé, 2008), was used together with the contact detection algorithm proposed by Boon et al. (2012). The critical sliding friction angle at the slide surface was sought using a strength reduction approach. A shear-softening contact model was used to model the shear resistance of the clayey layer at the slide surface. The results suggest that the critical sliding friction angle can be conservative if stability analyses are calculated based on the peak friction angles. The water table was assumed to be horizontal and the pore pressure at the clay layer was assumed to be hydrostatic. The influence of reservoir filling was marginal, increasing the sliding friction angle by only 1.6˚. The results of the DEM calculations were found to be sensitive to the orientations of the bedding planes and cross-joints. Finally, the failure mechanism was investigated and arching was found to be present at the bend of the chair-shaped slope. References Boon C.W., Houlsby G.T., Utili S. (2012). A new algorithm for contact detection between convex polygonal and polyhedral particles in the discrete element method. Computers and Geotechnics, vol 44, 73-82, doi.org/10.1016/j.compgeo.2012.03.012. Kozicki, J., & Donzé, F. V. (2008). A new open-source software developed for numerical simulations using discrete modeling methods. Computer Methods in Applied Mechanics and Engineering, 197(49-50), 4429-4443.

A three-dimensional FEM-DEM technique for predicting the evolution of fracture in geomaterials and concrete

NASA Astrophysics Data System (ADS)

Zárate, Francisco; Cornejo, Alejandro; Oñate, Eugenio

2018-07-01

This paper extends to three dimensions (3D), the computational technique developed by the authors in 2D for predicting the onset and evolution of fracture in a finite element mesh in a simple manner based on combining the finite element method and the discrete element method (DEM) approach (Zárate and Oñate in Comput Part Mech 2(3):301-314, 2015). Once a crack is detected at an element edge, discrete elements are generated at the adjacent element vertexes and a simple DEM mechanism is considered in order to follow the evolution of the crack. The combination of the DEM with simple four-noded linear tetrahedron elements correctly captures the onset of fracture and its evolution, as shown in several 3D examples of application.

Effect of DEM resolution and comparison between different weighting factors for hydrologic connectivity index

NASA Astrophysics Data System (ADS)

Cantreul, Vincent; Cavalli, Marco; Degré, Aurore

2016-04-01

The emerging concept of hydrological connectivity is difficult to quantify. Some indices have been proposed. The most cited is Borselli's one. It mainly uses the DEM as input. The pixel size may strongly impacts the result of the calculation. It has not been studied yet in silty areas. Another important aspect is the choice of the weighting factor which strongly influences the index value. The objective of this poster is so to compare 8 different DEM's resolutions (12, 24, 48, 72, 96, 204, 504 and 996cm) and 3 different weighting factors (factor C of Wischmeier, Manning's factor and rugosity index) in the Borselli's index calculation. The IC was calculated in a 124ha catchment (Hevillers), in the loess belt, in Belgium. The DEM used is coming from a UAV with a maximum resolution of 12 cm. Permanent covered surfaces are not considered in order to avoid artefact due to the vegetation (2% of the surface). Regarding the DEM pixel size, the IC increases for a given pixel when the pixel size decreases. That confirms some results observed in the Alpine region by Cavalli (2014). The mean difference between 12 cm and 10 m resolution is 35% with higher values up to 100% for higher connectivity zones (flow paths). Another result is the lower impact of connections in the watershed (grass strips…) at lower pixel sizes. This is linked to the small width of some connections which are sometimes comparing to cell size. Furthermore, a great loss of precision is observed from the 500 cm pixel size and upper. That remark is quite intuitive. Finally, some very well disconnected zones appear for the highest resolutions. Regarding the weighting factor, IC values calculated using C factor are lower than with the rugosity index which is only a topographic factor. With very high resolution DEM, it permits to represent the fine topography. For the C factor, the zones up to very well disconnected areas (grass strips, wood…) are well represented with lower index values than downstream

Seasonal and interannual evolution of Jakobshavn Isbrae, Greenland from a 2008-2015 high-res DEM and velocity time series

NASA Astrophysics Data System (ADS)

Shean, D. E.; Joughin, I.; Smith, B.; Floricioiu, D.

2015-12-01

Greenland's large marine-terminating outlet glaciers have displayed marked retreat, speedup, and thinning in recent decades. Jakobshavn Isbrae, one of Greenland's largest outlet glaciers, has retreated ~15 km, accelerated ~150%, and thinned ~200 m since the early 1990s. Here, we present a comprehensive analysis of high-resolution elevation (~2-5 m/px) and velocity (~100 m/px) time series with dense temporal coverage (daily-monthly). The Jakobshavn DEM time series consists of >70 WorldView-1/2/3 stereo DEMs and >11 TanDEM-X DEMs spanning 2008-2015. Complementary point elevation data from Operation IceBridge (ATM, LVIS), pre-IceBridge ATM flights, and ICESat-1 GLAS extend the surface elevation record to 1999 and provide essential absolute control data, enabling sub-meter horizontal/vertical accuracy for gridded DEMs. Velocity data are primarily derived from TerraSAR-X/TanDEM-X image pairs with 11-day interval from 2009-2015. These elevation and velocity data capture outlet glacier evolution with unprecedented detail during the post-ICESat era. The lower trunk of Jakobshavn displays significant seasonal velocity variations, with recent rates of ~8 km/yr during winter and >17 km/yr during summer. DEM data show corresponding seasonal elevation changes of -30 to -45 m in summer and +15 to +20 m in winter, with decreasing magnitude upstream. Seasonal discharge varies from ~30-35 Gt/yr in winter to ~45-55 Gt/yr in summer, and we integrate these measurements for improved long-term mass-balance estimates. Recent interannual trends show increased discharge, velocity, and thinning (-15 to -20 m/yr), which is consistent with long-term altimetry records. The DEM time series also reveal new details about calving front and mélange evolution during the seasonal cycle. Similar time series are available for Kangerdlugssuaq and Helheim Glaciers. These observations are improving our understanding of outlet glacier dynamics, while complementing ongoing efforts to constrain estimates

High-resolution DEM generation from multiple remote sensing data sources for improved volcanic hazard assessment - a case study from Nevado del Ruiz, Colombia

NASA Astrophysics Data System (ADS)

Deng, Fanghui; Dixon, Timothy H.; Rodgers, Mel; Charbonnier, Sylvain J.; Gallant, Elisabeth A.; Voss, Nicholas; Xie, Surui; Malservisi, Rocco; Ordoñez, Milton; López, Cristian M.

2017-04-01

Eruptions of active volcanoes in the presence of snow and ice can cause dangerous floods, avalanches and lahars, threatening millions of people living close to such volcanoes. Colombia's deadliest volcanic hazard in recorded history was caused by Nevado del Ruiz Volcano. On November 13, 1985, a relatively small eruption triggered enormous lahars, killing over 23,000 people in the city of Armero and 2,000 people in the town of Chinchina. Meltwater from a glacier capping the summit of the volcano was the main contributor to the lahars. From 2010 to present, increased seismicity, surface deformation, ash plumes and gas emissions have been observed at Nevado del Ruiz. The DEM is a key parameter for accurate prediction of the pathways of lava flows, pyroclastic flows, and lahars. While satellite coverage has greatly improved the quality of DEMs around the world, volcanoes remain a challenging target because of extremely rugged terrain with steep slopes and deeply cut valleys. In this study, three types of remote sensing data sources with different spatial scales (satellite radar interferometry, terrestrial radar interferometry (TRI), and structure from motion (SfM)) were combined to generate a high resolution DEM (10 m) of Nevado del Ruiz. 1) Synthetic aperture radar (SAR) images acquired by TSX/TDX satellites were applied to generate DEM covering most of the study area. To reduce the effect of geometric distortion inherited from SAR images, TSX/TDX DEMs from ascending and descending orbits were merged to generate a 10×10 m DEM. 2) TRI is a technique that uses a scanning radar to measure the amplitude and phase of a backscattered microwave signal. It provides a more flexible and reliable way to generate DEMs in steep-slope terrain compared with TSX/TDX satellites. The TRI was mounted at four different locations to image the upper slopes of the volcano. A DEM with 5×5 m resolution was generated by TRI. 3) SfM provides an alternative for shadow zones in both TSX/TDX and

Die Grundlagen der Fernsehtechnik: Systemtheorie und Technik der Bildübertragung

NASA Astrophysics Data System (ADS)

Mahler, Gerhard

Umfassende Einführung in die Grundlagen der Bewegtbild-Übertragung von den Anfängen bis zum heutigen Stand des digitalen Fernsehens mit einer aus der Praxis entstandenen systemtheoretischen Analyse. Die kompakte und anschaulich bebilderte Darstellung mit elementaren mathematischen Beschreibungen macht es dem Leser leicht, sich in die Bildübertragungstechnik einzuarbeiten. Thematische Einheiten erweitern den Wissensstoff - u.a. zu den Themen visuelle Wahrnehmung, mehrdimensionale Signaldarstellung, Farbmetrik, Digitalisierung, Elektronenoptik - und zeigen deren Anwendung auf die elektronische Bildübertragung.

Kundenfokus: Startpunkt für die digitale Transformation bei Stadtwerken

NASA Astrophysics Data System (ADS)

Fett, Perry; Küller, Philipp

Big Data, Internet der Dinge, Mobile Computing und soziale Medien - die modernen Informationstechnologien durchdringen den Alltag der meisten Menschen und lösen hierdurch eine digitale Transformation aus. Im Unternehmenskontext manifestiert sich die Digitalisierung durch eine neue Qualität der wissensbasierten Entscheidungsunterstützung und der Automatisierung bzw. Autonomisierung der Geschäftsprozesse. Für Stadtwerke gilt es nun, die Chancen der Digitalisierung zu ihren Gunsten zu nutzen. Ein Startpunkt könnte hierbei sein, wie Stadtwerke zukünftig mit ihren Kunden interagieren. Ausgelöst durch die Liberalisierung der Märkte rückt der Kunde heute stärker in den Mittelpunkt - die Energiewirtschaft steht nun vor der Herausforderung, dem Wettbewerb einen Schritt voraus zu sein und dem Kunden ein absolut positives Kundenerlebnis (Customer Experience) sowohl als Maßnahme zur Kundenbindung als auch zum Kundenaufbau zu bieten. Das vorliegende Kapitel zeigt hierfür die Erfolgskriterien für die gelungene Etablierung des Kundenfokus im eigenen Unternehmen auf. Mit dem Customer-Focus-Cycle-Modell von Fujitsu, angelehnt an den Deming-Kreislauf, wird ein allgemeingültiger Ansatz für ein mögliches Vorgehen beim Aufbau des Kundenfokus vorgestellt. Die sechs Phasen werden dabei anhand praktischer Beispiele erläutert und geben zudem Hinweise zu Methoden und Tools. Aus dem vorgestellten "Werkzeugkasten" wird ferner die Customer-Journey-Methode im Detail erläutert. Weiter soll das präsentierte Reifegradmodell Unternehmen dabei unterstützen, den eigenen Status quo festzustellen und die persönlichen Ziele auf dem Weg zur kundenzentrierten Organisation festzulegen.

Verbesserte Visualisierung der Koronararterien in MSCT-Daten mit direkter Vergleichbarkeit zur Angiographie

NASA Astrophysics Data System (ADS)

Lacalli, Christina; Jähne, Marion; Wesarg, Stefan

In diesem Beitrag stellen wir neue, automatisierte Verfahren zur Visualisierung der Koronararterien einerseits und für eine direkte Vergleichbarkeit mit konventionellen Angiogrammen andererseits vor. Unser Ansatz umfasst Methoden für die automatische Extraktion des Herzens aus kontrastverstärkten CT-Daten, sowie für die Maskierung grosser kontrastmittelgefüllter Kavitäten des Herzens, um die Sichtbarkeit der Koronararterien bei der Darstellung mittels Volumenrendering zu verbessern. Zum direkten Vergleich mit konventionellen Angiographien wurde ein Verfahren zur automatischen Generierung von Projektionsansichten aus den CT-Daten entwickelt.

GENETIC MAPPING OF VOCALIZATION TO A SERIES OF INCREASING ACUTE FOOTSHOCKS USING B6.A CONSOMIC AND B6.D2 CONGENIC MOUSE STRAINS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matthews, Douglas B; Chesler, Elissa J; Cook, Melloni N.

2008-01-01

Footshock response is used to study biological functions in mammals. However, the genetics underlying variability in footshock sensitivity are not well understood. In the current studies, a panel of B6.A consomic mouse strains, two B6.D2 congenic mouse strains and the progenitor strains were screened for footshock sensitivity as measured by audible vocalization. It was found that A/J (A) mice and C57BL/6J (B6) mice with an A Chromosome 1 (Chr 1) were less sensitive to footshock compared to B6 animals. Furthermore, the offspring of Chr 1 consomic mice crossed with B6 mice had vocalization levels that were intermediate to A/J andmore » B6 animals. A F2 mapping panel revealed two significant QTLs for footshock vocalization centered around D1Mit490 and D1Mit206 on Chr 1. The role of these Chr 1 loci in footshock sensitivity was confirmed in B6.D2 congenic mice. These data identify genetic regions involved in footshock sensitivity and establish additional mouse resources for use in investigating complex behaviors.« less

MIT Orients Course Materials Online to K-12

ERIC Educational Resources Information Center

Cavanagh, Sean

2008-01-01

Many science and mathematics educators across the country are taking advantage of a Web site created by the Massachusetts Institute of Technology (MIT), the famed research university located in Cambridge, Massachusetts, which offers free video, audio, and print lectures and course material taken straight from the school's classes. Those resources…

Influence of the external DEM on PS-InSAR processing and results on Northern Appennine slopes

NASA Astrophysics Data System (ADS)

Bayer, B.; Schmidt, D. A.; Simoni, A.

2014-12-01

We present an InSAR analysis of slow moving landslide in the Northern Appennines, Italy, and assess the dependencies on the choice of DEM. In recent years, advanced processing techniques for synthetic aperture radar interferometry (InSAR) have been applied to measure slope movements. The persistent scatterers (PS-InSAR) approach is probably the most widely used and some codes are now available in the public domain. The Stanford method of Persistent Scatterers (StamPS) has been successfully used to analyze landslide areas. One problematic step in the processing chain is the choice of an external DEM that is used to model and remove the topographic phase in a series of interferograms in order to obtain the phase contribution caused by surface deformation. The choice is not trivial, because the PS InSAR results differ significantly in terms of PS identification, positioning, and the resulting deformation signal. We use four different DEMs to process a set of 18 ASAR (Envisat) scenes over a mountain area (~350 km2) of the Northern Appennines of Italy, using StamPS. Slow-moving landslides control the evolution of the landscape and cover approximately 30% of the territory. Our focus in this presentation is to evaluate the influence of DEM resolution and accuracy by comparing PS-InSAR results. On an areal basis, we perform a statistical analysis of displacement time-series to make the comparison. We also consider two case studies to illustrate the differences in terms of PS identification, number and estimated displacements. It is clearly shown that DEM accuracy positively influences the number of PS, while line-of-sight rates differ from case to case and can result in deformation signals that are difficult to interpret. We also take advantage of statistical tools to analyze the obtained time-series datasets for the whole study area. Results indicate differences in the style and amount of displacement that can be related to the accuracy of the employed DEM.

GPU based contouring method on grid DEM data

NASA Astrophysics Data System (ADS)

Tan, Liheng; Wan, Gang; Li, Feng; Chen, Xiaohui; Du, Wenlong

2017-08-01

This paper presents a novel method to generate contour lines from grid DEM data based on the programmable GPU pipeline. The previous contouring approaches often use CPU to construct a finite element mesh from the raw DEM data, and then extract contour segments from the elements. They also need a tracing or sorting strategy to generate the final continuous contours. These approaches can be heavily CPU-costing and time-consuming. Meanwhile the generated contours would be unsmooth if the raw data is sparsely distributed. Unlike the CPU approaches, we employ the GPU's vertex shader to generate a triangular mesh with arbitrary user-defined density, in which the height of each vertex is calculated through a third-order Cardinal spline function. Then in the same frame, segments are extracted from the triangles by the geometry shader, and translated to the CPU-side with an internal order in the GPU's transform feedback stage. Finally we propose a "Grid Sorting" algorithm to achieve the continuous contour lines by travelling the segments only once. Our method makes use of multiple stages of GPU pipeline for computation, which can generate smooth contour lines, and is significantly faster than the previous CPU approaches. The algorithm can be easily implemented with OpenGL 3.3 API or higher on consumer-level PCs.

Parallelizing flow-accumulation calculations on graphics processing units—From iterative DEM preprocessing algorithm to recursive multiple-flow-direction algorithm

NASA Astrophysics Data System (ADS)

Qin, Cheng-Zhi; Zhan, Lijun

2012-06-01

As one of the important tasks in digital terrain analysis, the calculation of flow accumulations from gridded digital elevation models (DEMs) usually involves two steps in a real application: (1) using an iterative DEM preprocessing algorithm to remove the depressions and flat areas commonly contained in real DEMs, and (2) using a recursive flow-direction algorithm to calculate the flow accumulation for every cell in the DEM. Because both algorithms are computationally intensive, quick calculation of the flow accumulations from a DEM (especially for a large area) presents a practical challenge to personal computer (PC) users. In recent years, rapid increases in hardware capacity of the graphics processing units (GPUs) provided in modern PCs have made it possible to meet this challenge in a PC environment. Parallel computing on GPUs using a compute-unified-device-architecture (CUDA) programming model has been explored to speed up the execution of the single-flow-direction algorithm (SFD). However, the parallel implementation on a GPU of the multiple-flow-direction (MFD) algorithm, which generally performs better than the SFD algorithm, has not been reported. Moreover, GPU-based parallelization of the DEM preprocessing step in the flow-accumulation calculations has not been addressed. This paper proposes a parallel approach to calculate flow accumulations (including both iterative DEM preprocessing and a recursive MFD algorithm) on a CUDA-compatible GPU. For the parallelization of an MFD algorithm (MFD-md), two different parallelization strategies using a GPU are explored. The first parallelization strategy, which has been used in the existing parallel SFD algorithm on GPU, has the problem of computing redundancy. Therefore, we designed a parallelization strategy based on graph theory. The application results show that the proposed parallel approach to calculate flow accumulations on a GPU performs much faster than either sequential algorithms or other parallel GPU

Large-baseline InSAR for precise topographic mapping: a framework for TanDEM-X large-baseline data

NASA Astrophysics Data System (ADS)

Pinheiro, Muriel; Reigber, Andreas; Moreira, Alberto

2017-09-01

The global Digital Elevation Model (DEM) resulting from the TanDEM-X mission provides information about the world topography with outstanding precision. In fact, performance analysis carried out with the already available data have shown that the global product is well within the requirements of 10 m absolute vertical accuracy and 2 m relative vertical accuracy for flat to moderate terrain. The mission's science phase took place from October 2014 to December 2015. During this phase, bistatic acquisitions with across-track separation between the two satellites up to 3.6 km at the equator were commanded. Since the relative vertical accuracy of InSAR derived elevation models is, in principle, inversely proportional to the system baseline, the TanDEM-X science phase opened the doors for the generation of elevation models with improved quality with respect to the standard product. However, the interferometric processing of the large-baseline data is troublesome due to the increased volume decorrelation and very high frequency of the phase variations. Hence, in order to fully profit from the increased baseline, sophisticated algorithms for the interferometric processing, and, in particular, for the phase unwrapping have to be considered. This paper proposes a novel dual-baseline region-growing framework for the phase unwrapping of the large-baseline interferograms. Results from two experiments with data from the TanDEM-X science phase are discussed, corroborating the expected increased level of detail of the large-baseline DEMs.

MIT's interferometer CST testbed

NASA Technical Reports Server (NTRS)

Hyde, Tupper; Kim, ED; Anderson, Eric; Blackwood, Gary; Lublin, Leonard

1990-01-01

The MIT Space Engineering Research Center (SERC) has developed a controlled structures technology (CST) testbed based on one design for a space-based optical interferometer. The role of the testbed is to provide a versatile platform for experimental investigation and discovery of CST approaches. In particular, it will serve as the focus for experimental verification of CSI methodologies and control strategies at SERC. The testbed program has an emphasis on experimental CST--incorporating a broad suite of actuators and sensors, active struts, system identification, passive damping, active mirror mounts, and precision component characterization. The SERC testbed represents a one-tenth scaled version of an optical interferometer concept based on an inherently rigid tetrahedral configuration with collecting apertures on one face. The testbed consists of six 3.5 meter long truss legs joined at four vertices and is suspended with attachment points at three vertices. Each aluminum leg has a 0.2 m by 0.2 m by 0.25 m triangular cross-section. The structure has a first flexible mode at 31 Hz and has over 50 global modes below 200 Hz. The stiff tetrahedral design differs from similar testbeds (such as the JPL Phase B) in that the structural topology is closed. The tetrahedral design minimizes structural deflections at the vertices (site of optical components for maximum baseline) resulting in reduced stroke requirements for isolation and pointing of optics. Typical total light path length stability goals are on the order of lambda/20, with a wavelength of light, lambda, of roughly 500 nanometers. It is expected that active structural control will be necessary to achieve this goal in the presence of disturbances.

AMES Stereo Pipeline Derived DEM Accuracy Experiment Using LROC-NAC Stereopairs and Weighted Spatial Dependence Simulation for Lunar Site Selection

NASA Astrophysics Data System (ADS)

Laura, J. R.; Miller, D.; Paul, M. V.

2012-03-01

An accuracy assessment of AMES Stereo Pipeline derived DEMs for lunar site selection using weighted spatial dependence simulation and a call for outside AMES derived DEMs to facilitate a statistical precision analysis.

A metabolic signature for long life in the Caenorhabditis elegans Mit mutants.

PubMed

Butler, Jeffrey A; Mishur, Robert J; Bhaskaran, Shylesh; Rea, Shane L

2013-02-01

Mit mutations that disrupt function of the mitochondrial electron transport chain can, inexplicably, prolong Caenorhabditis elegans lifespan. In this study we use a metabolomics approach to identify an ensemble of mitochondrial-derived α-ketoacids and α-hydroxyacids that are produced by long-lived Mit mutants but not by other long-lived mutants or by short-lived mitochondrial mutants. We show that accumulation of these compounds is dependent on concerted inhibition of three α-ketoacid dehydrogenases that share dihydrolipoamide dehydrogenase (DLD) as a common subunit, a protein previously linked in humans with increased risk of Alzheimer's disease. When the expression of DLD in wild-type animals was reduced using RNA interference we observed an unprecedented effect on lifespan - as RNAi dosage was increased lifespan was significantly shortened, but, at higher doses, it was significantly lengthened, suggesting that DLD plays a unique role in modulating length of life. Our findings provide novel insight into the origin of the Mit phenotype. © 2012 The Authors Aging Cell © 2012 Blackwell Publishing Ltd/Anatomical Society of Great Britain and Ireland.

Influence of survey strategy and interpolation model on DEM quality

NASA Astrophysics Data System (ADS)

Heritage, George L.; Milan, David J.; Large, Andrew R. G.; Fuller, Ian C.

2009-11-01

Accurate characterisation of morphology is critical to many studies in the field of geomorphology, particularly those dealing with changes over time. Digital elevation models (DEMs) are commonly used to represent morphology in three dimensions. The quality of the DEM is largely a function of the accuracy of individual survey points, field survey strategy, and the method of interpolation. Recommendations concerning field survey strategy and appropriate methods of interpolation are currently lacking. Furthermore, the majority of studies to date consider error to be uniform across a surface. This study quantifies survey strategy and interpolation error for a gravel bar on the River Nent, Blagill, Cumbria, UK. Five sampling strategies were compared: (i) cross section; (ii) bar outline only; (iii) bar and chute outline; (iv) bar and chute outline with spot heights; and (v) aerial LiDAR equivalent, derived from degraded terrestrial laser scan (TLS) data. Digital Elevation Models were then produced using five different common interpolation algorithms. Each resultant DEM was differentiated from a terrestrial laser scan of the gravel bar surface in order to define the spatial distribution of vertical and volumetric error. Overall triangulation with linear interpolation (TIN) or point kriging appeared to provide the best interpolators for the bar surface. Lowest error on average was found for the simulated aerial LiDAR survey strategy, regardless of interpolation technique. However, comparably low errors were also found for the bar-chute-spot sampling strategy when TINs or point kriging was used as the interpolator. The magnitude of the errors between survey strategy exceeded those found between interpolation technique for a specific survey strategy. Strong relationships between local surface topographic variation (as defined by the standard deviation of vertical elevations in a 0.2-m diameter moving window), and DEM errors were also found, with much greater errors found at

Mass Loss of Larsen B Tributary Glaciers (Antarctic Peninsula) Unabated Since 2002

NASA Technical Reports Server (NTRS)

Berthier, Etienne; Scambos, Ted; Shuman, Christopher A.

2012-01-01

Ice mass loss continues at a high rate among the large glacier tributaries of the Larsen B Ice Shelf following its disintegration in 2002. We evaluate recent mass loss by mapping elevation changes between 2006 and 201011 using differencing of digital elevation models (DEMs). The measurement accuracy of these elevation changes is confirmed by a null test, subtracting DEMs acquired within a few weeks. The overall 2006201011 mass loss rate (9.0 2.1 Gt a-1) is similar to the 2001022006 rate (8.8 1.6 Gt a-1), derived using DEM differencing and laser altimetry. This unchanged overall loss masks a varying pattern of thinning and ice loss for individual glacier basins. On Crane Glacier, the thinning pulse, initially greatest near the calving front, is now broadening and migrating upstream. The largest losses are now observed for the HektoriaGreen glacier basin, having increased by 33 since 2006. Our method has enabled us to resolve large residual uncertainties in the Larsen B sector and confirm its state of ongoing rapid mass loss.

Release of a 10-m-resolution DEM for the whole Italian territory: a new, freely available resource for research purposes

NASA Astrophysics Data System (ADS)

Tarquini, S.; Nannipieri, L.; Favalli, M.; Fornaciai, A.; Vinci, S.; Doumaz, F.

2012-04-01

Digital elevation models (DEMs) are fundamental in any kind of environmental or morphological study. DEMs are obtained from a variety of sources and generated in several ways. Nowadays, a few global-coverage elevation datasets are available for free (e.g., SRTM, http://www.jpl.nasa.gov/srtm; ASTER, http://asterweb.jpl.nasa.gov/). When the matrix of a DEM is used also for computational purposes, the choice of the elevation dataset which better suits the target of the study is crucial. Recently, the increasing use of DEM-based numerical simulation tools (e.g. for gravity driven mass flows), would largely benefit from the use of a higher resolution/higher accuracy topography than those available at planetary scale. Similar elevation datasets are neither easily nor freely available for all countries worldwide. Here we introduce a new web resource which made available for free (for research purposes only) a 10 m-resolution DEM for the whole Italian territory. The creation of this elevation dataset was presented by Tarquini et al. (2007). This DEM was obtained in triangular irregular network (TIN) format starting from heterogeneous vector datasets, mostly consisting in elevation contour lines and elevation points derived from several sources. The input vector database was carefully cleaned up to obtain an improved seamless TIN refined by using the DEST algorithm, thus improving the Delaunay tessellation. The whole TINITALY/01 DEM was converted in grid format (10-m cell size) according to a tiled structure composed of 193, 50-km side square elements. The grid database consists of more than 3 billions of cells and occupies almost 12 GB of disk memory. A web-GIS has been created (http://tinitaly.pi.ingv.it/ ) where a seamless layer of images in full resolution (10 m) obtained from the whole DEM (both in color-shaded and anaglyph mode) is open for browsing. Accredited navigators are allowed to download the elevation dataset.

Development of a LiDAR derived digital elevation model (DEM) as Input to a METRANS geographic information system (GIS).

DOT National Transportation Integrated Search

2011-05-01

This report describes an assessment of digital elevation models (DEMs) derived from : LiDAR data for a subset of the Ports of Los Angeles and Long Beach. A methodology : based on Monte Carlo simulation was applied to investigate the accuracy of DEMs ...

MIT Clean Energy Prize: Final Technical Report May 12, 2010 - May 11, 2011

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snyder, Chris; Campbell, Georgina; Salony, Jason

2011-08-09

The MIT Clean Energy Prize (MIT CEP) is a venture creation and innovation competition to encourage innovation in the energy space, specifically with regard to clean energy. The Competition invited student teams from any US university to submit student-led ventures that demonstrate a high potential of successfully making clean energy more affordable, with a positive impact on the environment. By focusing on student ventures, the MIT CEP aims to educate the next generation of clean energy entrepreneurs. Teams receive valuable mentoring and hard deadlines that complement the cash prize to accelerate development of ventures. The competition is a year-long educationalmore » process that culminates in the selection of five category finalists and a Grand Prize winner and the distribution of cash prizes to each of those teams. Each entry was submitted in one of five clean energy categories: Renewables, Clean Non-Renewables, Energy Efficiency, Transportation, and Deployment.« less

Ice dynamics of Himalayan glaciers (Himachal Pradesh, India) using TerraSAR-X/TanDEM-X data.

NASA Astrophysics Data System (ADS)

Vijay, Saurabh; Braun, Matthias

2015-04-01

Mountain glaciers are the natural indicators of climate change. Himalaya is a part of widely spread mountain range consisting of second largest ice mass after polar region. The glaciers in Himalaya are located in Himachal Pradesh and other territories of India. The precipitation in the region is influenced by both Indian summer monsoon and mid-latitude winter westerlies. The glacier discharge influences the river basins and provides fresh water for various infrastructural necessities of urbanization in the state. The study aims to estimate the ice thickness and volume change during the decade (2011-2000) and annually during 2011-2014. For this, TanDEM-X DEMs are subtracted from the SRTM C/X band DEM of 2000. In addition, ice flow dynamics are quantified by the constellation of TerraSAR-X/TanDEM-X data using SAR offset tracking method. The primary investigations reveal that the terminus velocity of Bada Shigri (G077683E32169N), the biggest glacier of the state, Chhota Shigri( G077513E32227N), a bench-mark glacier, and other glacier (G077547E32162N) in 2011 found out to be < 2cm/day. The upper stream velocities of the glaciers are increased linearly and influenced by glacier tributaries.

A Seamless, High-Resolution, Coastal Digital Elevation Model (DEM) for Southern California

USGS Publications Warehouse

Barnard, Patrick L.; Hoover, Daniel

2010-01-01

A seamless, 3-meter digital elevation model (DEM) was constructed for the entire Southern California coastal zone, extending 473 km from Point Conception to the Mexican border. The goal was to integrate the most recent, high-resolution datasets available (for example, Light Detection and Ranging (Lidar) topography, multibeam and single beam sonar bathymetry, and Interferometric Synthetic Aperture Radar (IfSAR) topography) into a continuous surface from at least the 20-m isobath to the 20-m elevation contour. This dataset was produced to provide critical boundary conditions (bathymetry and topography) for a modeling effort designed to predict the impacts of severe winter storms on the Southern California coast (Barnard and others, 2009). The hazards model, run in real-time or with prescribed scenarios, incorporates atmospheric information (wind and pressure fields) with a suite of state-of-the-art physical process models (tide, surge, and wave) to enable detailed prediction of water levels, run-up, wave heights, and currents. Research-grade predictions of coastal flooding, inundation, erosion, and cliff failure are also included. The DEM was constructed to define the general shape of nearshore, beach and cliff surfaces as accurately as possible, with less emphasis on the detailed variations in elevation inland of the coast and on bathymetry inside harbors. As a result this DEM should not be used for navigation purposes.

Dissipation consistent fabric tensor definition from DEM to continuum for granular media

NASA Astrophysics Data System (ADS)

Li, X. S.; Dafalias, Y. F.

2015-05-01

In elastoplastic soil models aimed at capturing the impact of fabric anisotropy, a necessary ingredient is a measure of anisotropic fabric in the form of an evolving tensor. While it is possible to formulate such a fabric tensor based on indirect phenomenological observations at the continuum level, it is more effective and insightful to have the tensor defined first based on direct particle level microstructural observations and subsequently deduce a corresponding continuum definition. A practical means able to provide such observations, at least in the context of fabric evolution mechanisms, is the discrete element method (DEM). Some DEM defined fabric tensors such as the one based on the statistics of interparticle contact normals have already gained widespread acceptance as a quantitative measure of fabric anisotropy among researchers of granular material behavior. On the other hand, a fabric tensor in continuum elastoplastic modeling has been treated as a tensor-valued internal variable whose evolution must be properly linked to physical dissipation. Accordingly, the adaptation of a DEM fabric tensor definition to a continuum constitutive modeling theory must be thermodynamically consistent in regards to dissipation mechanisms. The present paper addresses this issue in detail, brings up possible pitfalls if such consistency is violated and proposes remedies and guidelines for such adaptation within a recently developed Anisotropic Critical State Theory (ACST) for granular materials.

High-resolution DEMs for High-mountain Asia: A systematic, region-wide assessment of geodetic glacier mass balance and dynamics

NASA Astrophysics Data System (ADS)

Shean, D. E.; Arendt, A. A.; Osmanoglu, B.; Montesano, P.

2017-12-01

High Mountain Asia (HMA) constitutes the largest glacierized region outside of the Earth's polar regions. Although available observations are limited, long-term records indicate sustained regional glacier mass loss since 1850, with increased loss in recent decades. Recent satellite data (e.g., GRACE, ICESat-1) show spatially variable glacier mass balance, with significant mass loss in the Himalaya and Hindu Kush and slight mass gain in the Karakoram. We generated 4000 high-resolution digital elevation models (DEMs) from sub-meter commercial stereo imagery (DigitalGlobe WorldView/GeoEye) acquired over glaciers in High-mountain Asia from 2002-present (mostly 2013-present). We produced a regional 8-m DEM mosaic for 2015 and estimated 15-year geodetic mass balance for 40000 glaciers larger than 0.1 km2. We are combining with other regional DEM sources to systematically document the spatiotemporal evolution of glacier mass balance for the entire HMA region. We also generated monthly to interannual DEM and velocity time series for high-priority sites distributed across the region, with >15-20 DEMs available for some locations from 2010-present. These records document glacier dynamics, seasonal snow accumulation/redistribution, and processes that affect glacier mass balance (e.g., ice-cliff retreat, debris cover evolution). These efforts will provide basin-scale assessments of snow/ice melt runoff contributions for model cal/val and downstream water resources applications. We will continue processing all archived and newly available commercial stereo imagery for HMA, and will release all DEMs through the HiMAT DAAC.

CFD-DEM Onset of Motion Analysis for Application to Bed Scour Risk Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sitek, M. A.; Lottes, S. A.

This CFD study with DEM was done as a part of the Federal Highway Administration’s (FHWA’s) effort to improve scour design procedures. The Computational Fluid Dynamics-Discrete Element Method (CFD-DEM) model, available in CD-Adapco’s StarCCM+ software, was used to simulate multiphase systems, mainly those which combine fluids and solids. In this method the motion of discrete solids is accounted for by DEM, which applies Newton's laws of motion to every particle. The flow of the fluid is determined by the local averaged Navier–Stokes equations that can be solved using the traditional CFD approach. The interactions between the fluid phase and solidsmore » phase are modeled by use of Newton's third law. The inter-particle contact forces are included in the equations of motion. Soft-particle formulation is used, which allows particles to overlap. In this study DEM was used to model separate sediment grains and spherical particles laying on the bed with the aim to analyze their movement due to flow conditions. Critical shear stress causing the incipient movement of the sediment was established and compared to the available experimental data. An example of scour around a cylindrical pier is considered. Various depths of the scoured bed and flow conditions were taken into account to gain a better understanding of the erosion forces existing around bridge foundations. The decay of these forces with increasing scour depth was quantified with a ‘decay function’, which shows that particles become increasingly less likely to be set in motion by flow forces as a scour hole increases in depth. Computational and experimental examples of the scoured bed around a cylindrical pier are presented.« less

Comparison of elevation derived from insar data with dem from topography map in Son Dong, Bac Giang, Viet Nam

NASA Astrophysics Data System (ADS)

Nguyen, Duy

2012-07-01

Digital Elevation Models (DEMs) are used in many applications in the context of earth sciences such as in topographic mapping, environmental modeling, rainfall-runoff studies, landslide hazard zonation, seismic source modeling, etc. During the last years multitude of scientific applications of Synthetic Aperture Radar Interferometry (InSAR) techniques have evolved. It has been shown that InSAR is an established technique of generating high quality DEMs from space borne and airborne data, and that it has advantages over other methods for the generation of large area DEM. However, the processing of InSAR data is still a challenging task. This paper describes InSAR operational steps and processing chain for DEM generation from Single Look Complex (SLC) SAR data and compare a satellite SAR estimate of surface elevation with a digital elevation model (DEM) from Topography map. The operational steps are performed in three major stages: Data Search, Data Processing, and product Validation. The Data processing stage is further divided into five steps of Data Pre-Processing, Co-registration, Interferogram generation, Phase unwrapping, and Geocoding. The Data processing steps have been tested with ERS 1/2 data using Delft Object-oriented Interferometric (DORIS) InSAR processing software. Results of the outcome of the application of the described processing steps to real data set are presented.

SediFoam: A general-purpose, open-source CFD-DEM solver for particle-laden flow with emphasis on sediment transport

NASA Astrophysics Data System (ADS)

Sun, Rui; Xiao, Heng

2016-04-01

With the growth of available computational resource, CFD-DEM (computational fluid dynamics-discrete element method) becomes an increasingly promising and feasible approach for the study of sediment transport. Several existing CFD-DEM solvers are applied in chemical engineering and mining industry. However, a robust CFD-DEM solver for the simulation of sediment transport is still desirable. In this work, the development of a three-dimensional, massively parallel, and open-source CFD-DEM solver SediFoam is detailed. This solver is built based on open-source solvers OpenFOAM and LAMMPS. OpenFOAM is a CFD toolbox that can perform three-dimensional fluid flow simulations on unstructured meshes; LAMMPS is a massively parallel DEM solver for molecular dynamics. Several validation tests of SediFoam are performed using cases of a wide range of complexities. The results obtained in the present simulations are consistent with those in the literature, which demonstrates the capability of SediFoam for sediment transport applications. In addition to the validation test, the parallel efficiency of SediFoam is studied to test the performance of the code for large-scale and complex simulations. The parallel efficiency tests show that the scalability of SediFoam is satisfactory in the simulations using up to O(107) particles.

Numerical modelling of powder caking at REV scale by using DEM

NASA Astrophysics Data System (ADS)

Guessasma, Mohamed; Silva Tavares, Homayra; Afrassiabian, Zahra; Saleh, Khashayar

2017-06-01

This work deals with numerical simulation of powder caking process caused by capillary condensation phenomenon. Caking consists in unwanted agglomeration of powder particles. This process is often irreversible and not easy to predict. To reproduce mechanism involved by caking phenomenon we have used the Discrete Elements Method (DEM). In the present work, we mainly focus on the role of capillary condensation and subsequent liquid bridge formation within a granular medium exposed to fluctuations of ambient relative humidity. Such bridges cause an attractive force between particles, leading to the formation of a cake with intrinsic physicochemical and mechanical properties. By considering a Representative Elementary Volume (REV), the DEM is then performed by means of a MULTICOR-3D software tacking into account the properties of the cake (degree of saturation) in order to establish relationships between the microscopic parameters and the macroscopic behaviour (tensile strength).

Insight into the adsorption profiles of the Saprolegnia monoica chitin synthase MIT domain on POPA and POPC membranes by molecular dynamics simulation studies.

PubMed

Kuang, Guanglin; Liang, Lijun; Brown, Christian; Wang, Qi; Bulone, Vincent; Tu, Yaoquan

2016-02-21

The critical role of chitin synthases in oomycete hyphal tip growth has been established. A microtubule interacting and trafficking (MIT) domain was discovered in the chitin synthases of the oomycete model organism, Saprolegnia monoica. MIT domains have been identified in diverse proteins and may play a role in intracellular trafficking. The structure of the Saprolegnia monoica chitin synthase 1 (SmChs1) MIT domain has been recently determined by our group. However, although our in vitro assay identified increased strength in interactions between the MIT domain and phosphatidic acid (PA) relative to other phospholipids including phosphatidylcholine (PC), the mechanism used by the MIT domain remains unknown. In this work, the adsorption behavior of the SmChs1 MIT domain on POPA and POPC membranes was systematically investigated by molecular dynamics simulations. Our results indicate that the MIT domain can adsorb onto the tested membranes in varying orientations. Interestingly, due to the specific interactions between MIT residues and lipid molecules, the binding affinity to the POPA membrane is much higher than that to the POPC membrane. A binding hotspot, which is critical for the adsorption of the MIT domain onto the POPA membrane, was also identified. The lower binding affinity to the POPC membrane can be attributed to the self-saturated membrane surface, which is unfavorable for hydrogen-bond and electrostatic interactions. The present study provides insight into the adsorption profile of SmChs1 and additionally has the potential to improve our understanding of other proteins containing MIT domains.

The topographic grain concept in DEM-based geomorphometric mapping

NASA Astrophysics Data System (ADS)

Józsa, Edina

2016-04-01

A common drawback of geomorphological analyses based on digital elevation datasets is the definition of search window size for the derivation of morphometric variables. The fixed-size neighbourhood determines the scale of the analysis and mapping, which can lead to the generalization of smaller surface details or the elimination of larger landform elements. The methods of DEM-based geomorphometric mapping are constantly developing into the direction of multi-scale landform delineation, but the optimal threshold for search window size is still a limiting factor. A possible way to determine the suitable value for the parameter is to consider the topographic grain principle (Wood, W. F. - Snell, J. B. 1960, Pike, R. J. et al. 1989). The calculation is implemented as a bash shell script for GRASS GIS to determine the optimal threshold for the r.geomorphon module. The approach relies on the potential of the topographic grain to detect the characteristic local ridgeline-to-channel spacing. By calculating the relative relief values with nested neighbourhood matrices it is possible to define a break-point where the increase rate of local relief encountered by the sample is significantly reducing. The geomorphons approach (Jasiewicz, J. - Stepinski, T. F. 2013) is a cell-based DEM classification method for the identification of landform elements at a broad range of scales by using line-of-sight technique. The landforms larger than the maximum lookup distance are broken down to smaller elements therefore the threshold needs to be set for a relatively large value. On the contrary, the computational requirements and the size of the study sites determine the upper limit for the value. Therefore the aim was to create a tool that would help to determine the optimal parameter for r.geomorphon tool. As a result it would be possible to produce more objective and consistent maps with achieving the full efficiency of this mapping technique. For the thorough analysis on the

Quantifying geological structures of the Nigde province in central Anatolia, Turkey using SRTM DEM data

NASA Astrophysics Data System (ADS)

Demirkesen, A. C.

2009-01-01

A digital terrain model and a 3D fly-through model of the Nigde province in central Anatolia, Turkey were generated and quantitatively analyzed employing the shuttle radar topographic mission (SRTM) digital elevation model (DEM). Besides, stream drainage patterns, lineaments and structural-geological features were extracted and analyzed. In the process of analyzing and interpreting the DEM for landforms, criteria such as color and color tones (attributes of heights), topography (shaded DEM and 3D fly-through model) and stream drainage patterns were employed to acquire geo-information about the land, such as hydrologic, geomorphologic, topographic and tectonic structures. In this study, the SRTM DEM data of the study region were experimentally used for both DEM classification and quantitative analysis of the digital terrain model. The results of the DEM classification are: (1) low plain including the plains of Bor and Altunhisar (20.7%); (2) high plain including the Misli (Konakli) plain (28.8%); (3) plateau plain including the Melendiz (Ciftlik) plateau plain (1.0%); (4) mountain including the Nigde massif (33.3%); and (5) high mountain (16.2%). High mountain areas include a caldera complex of Mt Melendiz, Mt Hasan and Mt Pozanti apart from the Ala mountains called Aladaglar and the Bolkar mountains called Bolkarlar in the study region (7,312 km2). Analysis of both the stream drainage patterns and the lineaments revealed that the Nigde province has a valley zone called Karasu valley zone (KVZ) or Nigde valley zone (NVZ), where settlements and agricultural plains, particularly the Bor plain in addition to settlements of the Bor town and the central city of Nigde have the most flooding risk when a heavy raining occurs. The study revealed that the NVZ diagonally divides the study region roughly into two equal parts, heading from northeast to southwest. According to the map created in this study, the right side of the NVZ has more mountainous area, where the Aladaglar

a Near-Global Bare-Earth dem from Srtm

NASA Astrophysics Data System (ADS)

Gallant, J. C.; Read, A. M.

2016-06-01

The near-global elevation product from NASA's Shuttle Radar Topographic Mission (SRTM) has been widely used since its release in 2005 at 3 arcsecond resolution and the release of the 1 arcsecond version in late 2014 means that the full potential of the SRTM DEM can now be realised. However the routine use of SRTM for analytical purposes such as catchment hydrology, flood inundation, habitat mapping and soil mapping is still seriously impeded by the presence of artefacts in the data, primarily the offsets due to tree cover and the random noise. This paper describes the algorithms being developed to remove those offsets, based on the methods developed to produce the Australian national elevation model from SRTM data. The offsets due to trees are estimated using the GlobeLand30 (National Geomatics Center of China) and Global Forest Change (University of Maryland) products derived from Landsat, along with the ALOS PALSAR radar image data (JAXA) and the global forest canopy height map (NASA). The offsets are estimated using several processes and combined to produce a single continuous tree offset layer that is subtracted from the SRTM data. The DEM products will be made freely available on completion of the first draft product, and the assessment of that product is expected to drive further improvements to the methods.

Frequency downconversion and phase noise in MIT.

PubMed

Watson, S; Williams, R J; Griffiths, H; Gough, W; Morris, A

2002-02-01

High-frequency (3-30 MHz) operation of MIT systems offers advantages in terms of the larger induced signal amplitudes compared to systems operating in the low- or medium-frequency ranges. Signal distribution at HF, however, presents difficulties, in particular with isolation and phase stability. It is therefore valuable to translate received signals to a lower frequency range through heterodyne downconversion, a process in which relative signal amplitude and phase information is in theory retained. Measurement of signal amplitude and phase is also simplified at lower frequencies. The paper presents details of measurements on a direct phase measurement system utilizing heterodyne downconversion and compares the relative performance of three circuit configurations. The 100-sample average precision of a circuit suitable for use as a receiver within an MIT system was 0.008 degrees for input amplitude -21 dBV. As the input amplitude was reduced from -21 to -72 dBV variation in the measured phase offset was observed, with the offset varying by 1.8 degrees. The precision of the circuit deteriorated with decreasing input amplitude, but was found to provide a 100-sample average precision of <0.022 degrees down to an input amplitude of -60 dBV. The characteristics of phase noise within the system are discussed.

BOREAS HYD-8 DEM Data Over the NSA-MSA and SSA-MSA in the UTM Projection

NASA Technical Reports Server (NTRS)

Wang, Xue-Wen; Hall, Forrest G. (Editor); Knapp, David E. (Editor); Band, L. E.; Smith, David E. (Technical Monitor)

2000-01-01

The BOREAS HYD-8 team focused on describing the scaling behavior of water and carbon flux processes at local and regional scales. These DEMs were produced from digitized contours at a cell resolution of 100 meters. Vector contours of the area were used as input to a software package that interpolates between contours to create a DEM representing the terrain surface. The vector contours had a contour interval of 25 feet. The data cover the BOREAS MSAs of the SSA and NSA and are given in a UTM map projection. Most of the elevation data from which the DEM was produced were collected in the 1970s or 1980s. The data are stored in binary, image format files. The data files are available on a CD-ROM (see document number 20010000884) or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Validation of the Omron MIT Elite blood pressure device in a pregnant population with large arm circumference.

PubMed

James, Lauren; Nzelu, Diane; Hay, Anna; Shennan, Andrew; Kametas, Nikos A

2017-04-01

The aim of this study was to evaluate the accuracy of the Omron MIT Elite automated device in pregnant women with an arm circumference of or above 32 cm, using the British Hypertension Society validation protocol. Blood pressure was measured sequentially in 46 women of any gestation requiring the use of a large cuff (arm circumference ≥32 cm) alternating between the mercury sphygmomanometer and the Omron MIT Elite device. The Omron MIT Elite achieved an overall D/D grade with a mean of the device-observer difference being 7.17±6.67 and 9.31±6.59 for systolic and diastolic blood pressure respectively. Interobserver accuracy was 94.6% for systolic and 95% for diastolic readings within 5 mmHg. The Omron MIT Elite overestimates blood pressure and has failed the British Hypertension Society protocol requirements. Therefore, it cannot be recommended for use in pregnant women with an arm circumference of or above 32 cm.

CurrMIT: A Tool for Managing Medical School Curricula.

ERIC Educational Resources Information Center

Salas, Albert A.; Anderson, M. Brownell; LaCourse, Lisa; Allen, Robert; Candler, Chris S.; Cameron, Terri; Lafferty, Debra

2003-01-01

The Association of American Medical Colleges (AAMC) Curriculum Management & Information Tool (CurrMIT) is a relational database containing curriculum information from medical schools throughout the United States and Canada. This article gives an overview of the technology upon which the system is built and the training materials and workshops…

The Effect of DEM Source and Grid Size on the Index of Connectivity in Savanna Catchments

NASA Astrophysics Data System (ADS)

Jarihani, Ben; Sidle, Roy; Bartley, Rebecca; Roth, Christian

2017-04-01

The term "hydrological connectivity" is increasingly used instead of sediment delivery ratio to describe the linkage between the sources of water and sediment within a catchment to the catchment outlet. Sediment delivery ratio is an empirical parameter that is highly site-specific and tends to lump all processes, whilst hydrological connectivity focuses on the spatially-explicit hydrologic drivers of surficial processes. Detailed topographic information plays a fundamental role in geomorphological interpretations as well as quantitative modelling of sediment fluxes and connectivity. Geomorphometric analysis permits a detailed characterization of drainage area and drainage pattern together with the possibility of characterizing surface roughness. High resolution topographic data (i.e., LiDAR) are not available for all areas; however, remotely sensed topographic data from multiple sources with different grid sizes are used to undertake geomorphologic analysis in data-sparse regions. The Index of Connectivity (IC), a geomorphometric model based only on DEM data, is applied in two small savanna catchments in Queensland, Australia. The influence of the scale of the topographic data is explored by using DEMs from LiDAR ( 1 m), WorldDEM ( 10 m), raw SRTM and hydrologically corrected SRTM derived data ( 30 m) to calculate the index of connectivity. The effect of the grid size is also investigated by resampling the high resolution LiDAR DEM to multiple grid sizes (e.g. 5, 10, 20 m) and comparing the extracted IC.

Combining remote sensing image with DEM to identify ancient Minqin Oasis, northwest of China

NASA Astrophysics Data System (ADS)

Xie, Yaowen

2008-10-01

The developing and desertification process of Minqin oasis is representative in the whole arid area of northwest China. Combining Remote Sensing image with Digital Elevation Model (DEM) can produce the three-dimensional image of the research area which can give prominence to the spatial background of historical geography phenomenon's distribution, providing the conditions for extracting and analyzing historical geographical information thoroughly. This research rebuilds the ancient artificial Oasis based on the three-dimensional images produced by the TM digital Remote Sensing image and DEM created using 1:100000 topographic maps. The result indicates that the whole area of the ancient artificial oasis in Minqin Basin over the whole historical period reaches 321km2, in the form of discontinuous sheet, separated on the two banks of ancient Shiyang River and its branches, namely, Xishawo area, west to modern Minqin Basin and Zhongshawo area, in the center of the oasis. Except for a little of the ancient oasis unceasingly used by later people, most of it became desert. The combination of digital Remote Sensing image and DEM can integrate the advantages of both in identifying ancient oasis and improve the interpreting accuracy greatly.

Influence of different DEMs on the quality of the InSAR results: case study over Bankya and Mirovo areas

NASA Astrophysics Data System (ADS)

Nikolov, Hristo; Atanasova, Mila

2017-10-01

One of the key input parameters in obtaining end products from SAR data is the DEM used during their processing. This holds true especially when persistent scatterers InSAR method should be applied for example to study slow moving landslides or subsidence. Since nowadays most of the raw SAR data are of space borne origin for their correct processing to high precision products for relatively small areas with centimeter accuracy a DEM taking into account the particularities of the local topography is needed. Most of the DEMs used by the SAR processing software such as SRTM or ASTER are obtained by the same type of instrument and present some disagreements with height information acquired by leveling measurements or other geodetic means. This was the motivation for initiating this research - to prove the need of creating and using local DEM in SAR data processing at small scale and to check what the magnitude of the discrepancy between final InSAR products is in both cases where SRTM/ASTER and local DEM has been used. In addition investigated were two scenarios for SAR data processing - one with small baseline between image pairs and one having large baseline image pairs - in order to find out in which case local DEM has bigger impact. In course of this study two reference areas were considered - Bankya village near Sofia (SW region of Bulgaria) and Mirovo salt extraction site (NE region of Bulgaria). The reason those areas were selected lies in the high number of landslides registered and monitored by the competent authorities in the mentioned locations. The significance of the results obtained is witnessed by the fact that both sites we used have been included as reference sites for Bulgaria in the PanGeo EU funded project dealing with delivering information regarding ground instability geohazard as areas prone to subsidence of natural and manmade origin. In the said project largest part of the information has been extracted from Envisat SAR data, but now this

Mapping debris-flow hazard in Honolulu using a DEM

USGS Publications Warehouse

Ellen, Stephen D.; Mark, Robert K.; ,

1993-01-01

A method for mapping hazard posed by debris flows has been developed and applied to an area near Honolulu, Hawaii. The method uses studies of past debris flows to characterize sites of initiation, volume at initiation, and volume-change behavior during flow. Digital simulations of debris flows based on these characteristics are then routed through a digital elevation model (DEM) to estimate degree of hazard over the area.

Fusion of Laser Altimetry Data with Dems Derived from Stereo Imaging Systems

NASA Astrophysics Data System (ADS)

Schenk, T.; Csatho, B. M.; Duncan, K.

2016-06-01

During the last two decades surface elevation data have been gathered over the Greenland Ice Sheet (GrIS) from a variety of different sensors including spaceborne and airborne laser altimetry, such as NASA's Ice Cloud and land Elevation Satellite (ICESat), Airborne Topographic Mapper (ATM) and Laser Vegetation Imaging Sensor (LVIS), as well as from stereo satellite imaging systems, most notably from Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) and Worldview. The spatio-temporal resolution, the accuracy, and the spatial coverage of all these data differ widely. For example, laser altimetry systems are much more accurate than DEMs derived by correlation from imaging systems. On the other hand, DEMs usually have a superior spatial resolution and extended spatial coverage. We present in this paper an overview of the SERAC (Surface Elevation Reconstruction And Change detection) system, designed to cope with the data complexity and the computation of elevation change histories. SERAC simultaneously determines the ice sheet surface shape and the time-series of elevation changes for surface patches whose size depends on the ruggedness of the surface and the point distribution of the sensors involved. By incorporating different sensors, SERAC is a true fusion system that generates the best plausible result (time series of elevation changes) a result that is better than the sum of its individual parts. We follow this up with an example of the Helmheim gacier, involving ICESat, ATM and LVIS laser altimetry data, together with ASTER DEMs.

Kanban - der Weg ist das Ziel

NASA Astrophysics Data System (ADS)

Aull, Florian; Berlak, Joachim; Dickmann, Eva; Dickmann, Philipp; Fischäder, Holm; Gerlach, Joachim; Henneberg, Jens; Kapalla, Klaus; Kress, Oliver; Kuttler, Robert; Schneider, Herfried M.; Schürle, Philipp; Stellpflug, Franz-Josef; Wannenwetsch, Ralph; Wulz, Johannes; Zäh, Michael F.

Wenn man aktuell Produktionsbereiche in Deutschland und Europa besucht, fallen im Zusammenhang mit modernen Produktionsmethoden immer öfter die Begriffe Kanban (jap. Karte, Signal) und Pull-Produktion, und dies nicht ohne Stolz, da diese mit dem schillernden Vorbild des Toyota Produktionssystems in Zusammenhang stehen. Tatsächlich ist Kanban ein integraler Bestandteil moderner Produktionssysteme. Blickt man aber im Rahmen von Prozessanalysen hinter die Fassaden", d. h. in die tägliche Praxis der Arbeitsprozesse, wird man schnell desillusioniert - die viel gepriesenen klassischen Kanban-Regeln werden im Tagesgeschäft nicht eingehalten.

Accuracy assessment of TanDEM-X IDEM using airborne LiDAR on the area of Poland

NASA Astrophysics Data System (ADS)

Woroszkiewicz, Małgorzata; Ewiak, Ireneusz; Lulkowska, Paulina

2017-06-01

The TerraSAR-X add-on for Digital Elevation Measurement (TanDEM-X) mission launched in 2010 is another programme - after the Shuttle Radar Topography Mission (SRTM) in 2000 - that uses space-borne radar interferometry to build a global digital surface model. This article presents the accuracy assessment of the TanDEM-X intermediate Digital Elevation Model (IDEM) provided by the German Aerospace Center (DLR) under the project "Accuracy assessment of a Digital Elevation Model based on TanDEM-X data" for the southwestern territory of Poland. The study area included: open terrain, urban terrain and forested terrain. Based on a set of 17,498 reference points acquired by airborne laser scanning, the mean errors of average heights and standard deviations were calculated for areas with a terrain slope below 2 degrees, between 2 and 6 degrees and above 6 degrees. The absolute accuracy of the IDEM data for the analysed area, expressed as a root mean square error (Total RMSE), was 0.77 m.

Multi-scale sensitivity analysis of pile installation using DEM

NASA Astrophysics Data System (ADS)

Esposito, Ricardo Gurevitz; Velloso, Raquel Quadros; , Eurípedes do Amaral Vargas, Jr.; Danziger, Bernadete Ragoni

2017-12-01

The disturbances experienced by the soil due to the pile installation and dynamic soil-structure interaction still present major challenges to foundation engineers. These phenomena exhibit complex behaviors, difficult to measure in physical tests and to reproduce in numerical models. Due to the simplified approach used by the discrete element method (DEM) to simulate large deformations and nonlinear stress-dilatancy behavior of granular soils, the DEM consists of an excellent tool to investigate these processes. This study presents a sensitivity analysis of the effects of introducing a single pile using the PFC2D software developed by Itasca Co. The different scales investigated in these simulations include point and shaft resistance, alterations in porosity and stress fields and particles displacement. Several simulations were conducted in order to investigate the effects of different numerical approaches showing indications that the method of installation and particle rotation could influence greatly in the conditions around the numerical pile. Minor effects were also noted due to change in penetration velocity and pile-soil friction. The difference in behavior of a moving and a stationary pile shows good qualitative agreement with previous experimental results indicating the necessity of realizing a force equilibrium process prior to any load-test to be simulated.

Multi-scale sensitivity analysis of pile installation using DEM

NASA Astrophysics Data System (ADS)

Esposito, Ricardo Gurevitz; Velloso, Raquel Quadros; , Eurípedes do Amaral Vargas, Jr.; Danziger, Bernadete Ragoni

2018-07-01

The disturbances experienced by the soil due to the pile installation and dynamic soil-structure interaction still present major challenges to foundation engineers. These phenomena exhibit complex behaviors, difficult to measure in physical tests and to reproduce in numerical models. Due to the simplified approach used by the discrete element method (DEM) to simulate large deformations and nonlinear stress-dilatancy behavior of granular soils, the DEM consists of an excellent tool to investigate these processes. This study presents a sensitivity analysis of the effects of introducing a single pile using the PFC2D software developed by Itasca Co. The different scales investigated in these simulations include point and shaft resistance, alterations in porosity and stress fields and particles displacement. Several simulations were conducted in order to investigate the effects of different numerical approaches showing indications that the method of installation and particle rotation could influence greatly in the conditions around the numerical pile. Minor effects were also noted due to change in penetration velocity and pile-soil friction. The difference in behavior of a moving and a stationary pile shows good qualitative agreement with previous experimental results indicating the necessity of realizing a force equilibrium process prior to any load-test to be simulated.

MIT Mints a Valuable New Form of Academic Currency

ERIC Educational Resources Information Center

Carey, Kevin

2012-01-01

The Massachusetts Institute of Technology (MIT) has invented or improved many world-changing things--radar, information theory, and synthetic self-replicating molecules, to name a few. Last month the university announced, to mild fanfare, an invention that could be similarly transformative, this time for higher education itself. It is called MITx.…

Educational Outreach at the M.I.T. Plasma Fusion Center

NASA Astrophysics Data System (ADS)

Censabella, V.

1996-11-01

Educational outreach at the MIT Plasma Fusion Center consists of volunteers working together to increase the public's knowledge of fusion and plasma-related experiments. Seeking to generate excitement about science, engineering and mathematics, the PFC holds a number of outreach activities throughout the year, such as Middle and High School Outreach Days. Outreach also includes the Mr. Magnet Program, which uses an interactive strategy to engage elementary school children. Included in this year's presentation will be a new and improved C-MOD Jr, a confinement video game which helps students to discover how computers manipulate magnetic pulses to keep a plasma confined for as long as possible. Also on display will be an educational toy created by the Cambridge Physics Outlet, a PFC spin-off company. The PFC maintains a Home Page on the World Wide Web, which can be reached at http://cmod2.pfc.mit.edu/.

Insight From the Statistics of Nothing: Estimating Limits of Change Detection Using Inferred No-Change Areas in DEM Difference Maps and Application to Landslide Hazard Studies

NASA Astrophysics Data System (ADS)

Haneberg, W. C.

2017-12-01

Remote characterization of new landslides or areas of ongoing movement using differences in high resolution digital elevation models (DEMs) created through time, for example before and after major rains or earthquakes, is an attractive proposition. In the case of large catastrophic landslides, changes may be apparent enough that simple subtraction suffices. In other cases, statistical noise can obscure landslide signatures and place practical limits on detection. In ideal cases on land, GPS surveys of representative areas at the time of DEM creation can quantify the inherent errors. In less-than-ideal terrestrial cases and virtually all submarine cases, it may be impractical or impossible to independently estimate the DEM errors. Examining DEM difference statistics for areas reasonably inferred to have no change, however, can provide insight into the limits of detectability. Data from inferred no-change areas of airborne LiDAR DEM difference maps of the 2014 Oso, Washington landslide and landslide-prone colluvium slopes along the Ohio River valley in northern Kentucky, show that DEM difference maps can have non-zero mean and slope dependent error components consistent with published studies of DEM errors. Statistical thresholds derived from DEM difference error and slope data can help to distinguish between DEM differences that are likely real—and which may indicate landsliding—from those that are likely spurious or irrelevant. This presentation describes and compares two different approaches, one based upon a heuristic assumption about the proportion of the study area likely covered by new landslides and another based upon the amount of change necessary to ensure difference at a specified level of probability.

Umgang mit Antithrombotika bei Operationen an der Haut vor und nach Publikation der entsprechenden S3-Leitlinie.

PubMed

Gaskins, Matthew; Dittmann, Martin; Eisert, Lisa; Werner, Ricardo Niklas; Dressler, Corinna; Löser, Christoph; Nast, Alexander

2018-03-01

Laut einer Befragung im Jahre 2012 war der Umgang mit Antithrombotika bei dermatochirurgischen Eingriffen in Deutschland sehr heterogen. 2014 wurde erstmals eine evidenzbasierte Leitlinie zu diesem Thema veröffentlicht. Es wurde eine anonyme Befragung derselben Stichprobe zum Umgang mit Antithrombotika sowie zu Kenntnissen der Leitlinie durchgeführt. Die Ergebnisse wurden als relative Häufigkeiten berichtet und denen aus 2012 gegenübergestellt. 208 Antwortbögen wurden ausgewertet (Rücklaufquote: 36,6 %). Die große Mehrheit der Dermatologen erklärte, kleinere Eingriffe unter Fortführung der Therapie mit Phenprocoumon, niedrig dosierter Acetylsalicylsäure (≤ 100 mg) und Clopidogrel sowie mit direkten oralen Antikoagulanzien durchzuführen. Bei größeren Eingriffen war der Umgang hingegen weiterhin heterogen, insbesondere unter niedergelassenen Dermatologen. Der Anteil der Dermatologen, die Phenprocoumon, Acetylsalicylsäure und Clopidogrel leitlinienkonform verwendeten, hat sich insgesamt vergrößert. Führten 2012 beispielsweise 53,8 % der Klinikärzte bzw. 36,3 % der niedergelassenen Dermatologen eine große Exzision unter Fortführung der Therapie mit niedrig dosierter Acetylsalicylsäure durch, taten dies 2017 90,2 % bzw. 57,8 % (Phenprocoumon: 33,8 % bzw. 11,9 % auf 63,9 % bzw. 29,9 %; Clopidogrel: 36,9 % bzw. 23,2 % auf 63,9 % bzw. 30,6 %). Unter den Klinikärzten war ein hoher Anteil mit der Leitlinie vertraut und fand diese hilfreich. Eine Zunahme des leitlinienkonformen Verhaltens war bei allen Eingriffen zu verzeichnen. Bei größeren Eingriffen zeigte sich trotz deutlicher Verbesserung die Notwendigkeit verstärkter Anstrengungen zur Leitlinienumsetzung bzw. zur Identifizierung von Implementierungsbarrieren. © 2018 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

Center for Multiscale Plasma Dynamics: Report on Activities (UCLA/MIT), 2009-2010

DOE Office of Scientific and Technical Information (OSTI.GOV)

Troy Carter

2011-04-18

The final 'phaseout' year of the CMPD ended July 2010; a no cost extension was requested until May 2011 in order to enable the MIT subcontract funds to be fully utilized. Research progress over this time included verification and validation activities for the BOUT and BOUT++ code, studies of spontaneous reconnection in the VTF facility at MIT, and studies of the interaction between Alfven waves and drift waves in LAPD. The CMPD also hosted the 6th plasma physics winter school in 2010 (jointly with the NSF frontier center the Center for Magnetic Self-Organization, significant funding came from NSF for thismore » most recent iteration of the Winter School).« less

Center for Multiscale Plasma Dynamics: Report on Activities (UCLA/MIT), 2009-2010

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carter, Troy Alan

2014-10-03

The final “phaseout” year of the CMPD ended July 2010; a no cost extension was requested until May 2011 in order to enable the MIT subcontract funds to be fully utilized. Research progress over this time included verification and validation activities for the BOUT and BOUT++ code, studies of spontaneous reconnection in the VTF facility at MIT, and studies of the interaction between Alfv´en waves and drift waves in LAPD. The CMPD also hosted the 6th plasma physics winter school in 2010 (jointly with the NSF frontier center the Center for Magnetic Self-Organization, significant funding came from NSF for thismore » most recent iteration of theWinter School).« less

Mapping hydrological environments in central Amazonia: ground validation and surface model based on SRTM DEM data corrected for deforestation

NASA Astrophysics Data System (ADS)

Moulatlet, G. M.; Rennó, C. D.; Costa, F. R. C.; Emilio, T.; Schietti, J.

2014-07-01

One of the most important freely available digital elevation models (DEMs) for Amazonia is the one obtained by the Shuttle Radar Topography Mission (SRTM). However, since SRTM tends to represent the vegetation surface instead of the ground surface, the broad use of SRTM DEM as a framework for terrain description in Amazonia is hampered by the presence of deforested areas. We present here two datasets: (1) a deforestation-corrected SRTM DEM for the interfluve between the Purus and Madeira rivers, in central Amazonia, which passed through a careful identification of different environments and has deforestation features corrected by a new method of increasing pixel values of the DEM; and (2) a set of eighteen hydrological-topographic descriptors based on the corrected SRTM DEM. The hydrological-topographic description was generated by the Height Above the Nearest Drainage (HAND) algorithm, which normalizes the terrain elevation (a.s.l.) by the elevation of the nearest hydrologically connected drainage. The validation of the HAND dataset was done by in situ hydrological description of 110 km of walking trails also available in this dataset. The new SRTM DEM expands the applicability of SRTM data for landscape modelling; and the datasets of hydrological features based on topographic modelling is undoubtedly appropriate for ecological modelling and an important contribution for environmental mapping of Amazonia. The deforestation-corrected SRTM DEM is available at http://ppbio.inpa.gov.br/knb/metacat/naman.318.3/ppbio; the polygons selected for deforestation correction are available at http://ppbio.inpa.gov.br/knb/metacat/naman.317.3/ppbio; the set of hydrological-topographic descriptors is available at Development and evaluation of form three mathematics i-Think module (Mi-T3) on algebraic formulae topic

NASA Astrophysics Data System (ADS)

Sam, Sazilah; Abdullah, Mohd Faizal Nizam Lee

2017-05-01

This article introduces the Form Three Mathematics i-Think Module (Mi-T3). The main objective of this Mi-T3 is to assist form three students develop their higher order thinking skills (HOTS). The Sidek Module Development Model (SMDM) and eight innovative thinking maps (i-Think) were applied as a guideline in developing Mi-T3. A validation stage was carried out by eight experts, and content validation achievement more than 90% obtained. A group of form three students and teachers was piloted to check the module's reliability through one to one and small group evaluation and Cronbach Alpha more than 0.90 was obtained. Implications of the study are discussed in this article.

Optimizing landslide susceptibility zonation: Effects of DEM spatial resolution and slope unit delineation on logistic regression models

NASA Astrophysics Data System (ADS)

Schlögel, R.; Marchesini, I.; Alvioli, M.; Reichenbach, P.; Rossi, M.; Malet, J.-P.

2018-01-01

We perform landslide susceptibility zonation with slope units using three digital elevation models (DEMs) of varying spatial resolution of the Ubaye Valley (South French Alps). In so doing, we applied a recently developed algorithm automating slope unit delineation, given a number of parameters, in order to optimize simultaneously the partitioning of the terrain and the performance of a logistic regression susceptibility model. The method allowed us to obtain optimal slope units for each available DEM spatial resolution. For each resolution, we studied the susceptibility model performance by analyzing in detail the relevance of the conditioning variables. The analysis is based on landslide morphology data, considering either the whole landslide or only the source area outline as inputs. The procedure allowed us to select the most useful information, in terms of DEM spatial resolution, thematic variables and landslide inventory, in order to obtain the most reliable slope unit-based landslide susceptibility assessment.

Anti-aliasing filters for deriving high-accuracy DEMs from TLS data: A case study from Freeport, Texas

NASA Astrophysics Data System (ADS)

Xiong, L.; Wang, G.; Wessel, P.

2017-12-01

Terrestrial laser scanning (TLS), also known as ground-based Light Detection and Ranging (LiDAR), has been frequently applied to build bare-earth digital elevation models (DEMs) for high-accuracy geomorphology studies. The point clouds acquired from TLS often achieve a spatial resolution at fingerprint (e.g., 3cm×3cm) to handprint (e.g., 10cm×10cm) level. A downsampling process has to be applied to decimate the massive point clouds and obtain portable DEMs. It is well known that downsampling can result in aliasing that causes different signal components to become indistinguishable when the signal is reconstructed from the datasets with a lower sampling rate. Conventional DEMs are mainly the results of upsampling of sparse elevation measurements from land surveying, satellite remote sensing, and aerial photography. As a consequence, the effects of aliasing have not been fully investigated in the open literature of DEMs. This study aims to investigate the spatial aliasing problem and implement an anti-aliasing procedure of regridding dense TLS data. The TLS data collected in the beach and dune area near Freeport, Texas in the summer of 2015 are used for this study. The core idea of the anti-aliasing procedure is to apply a low-pass spatial filter prior to conducting downsampling. This article describes the successful use of a fourth-order Butterworth low-pass spatial filter employed in the Generic Mapping Tools (GMT) software package as anti-aliasing filters. The filter can be applied as an isotropic filter with a single cutoff wavelength or as an anisotropic filter with different cutoff wavelengths in the X and Y directions. The cutoff wavelength for the isotropic filter is recommended to be three times the grid size of the target DEM.

Anti-aliasing filters for deriving high-accuracy DEMs from TLS data: A case study from Freeport, Texas

NASA Astrophysics Data System (ADS)

Xiong, Lin.; Wang, Guoquan; Wessel, Paul

2017-03-01

Terrestrial laser scanning (TLS), also known as ground-based Light Detection and Ranging (LiDAR), has been frequently applied to build bare-earth digital elevation models (DEMs) for high-accuracy geomorphology studies. The point clouds acquired from TLS often achieve a spatial resolution at fingerprint (e.g., 3 cm×3 cm) to handprint (e.g., 10 cm×10 cm) level. A downsampling process has to be applied to decimate the massive point clouds and obtain manageable DEMs. It is well known that downsampling can result in aliasing that causes different signal components to become indistinguishable when the signal is reconstructed from the datasets with a lower sampling rate. Conventional DEMs are mainly the results of upsampling of sparse elevation measurements from land surveying, satellite remote sensing, and aerial photography. As a consequence, the effects of aliasing caused by downsampling have not been fully investigated in the open literature of DEMs. This study aims to investigate the spatial aliasing problem of regridding dense TLS data. The TLS data collected from the beach and dune area near Freeport, Texas in the summer of 2015 are used for this study. The core idea of the anti-aliasing procedure is to apply a low-pass spatial filter prior to conducting downsampling. This article describes the successful use of a fourth-order Butterworth low-pass spatial filter employed in the Generic Mapping Tools (GMT) software package as an anti-aliasing filter. The filter can be applied as an isotropic filter with a single cutoff wavelength or as an anisotropic filter with two different cutoff wavelengths in the X and Y directions. The cutoff wavelength for the isotropic filter is recommended to be three times the grid size of the target DEM.

High Resolution Airborne InSAR DEM of Bagley Ice Valley, South-central Alaska: Geodetic Validation with Airborne Laser Altimeter Data

NASA Astrophysics Data System (ADS)

Muskett, R. R.; Lingle, C. S.; Echelmeyer, K. A.; Valentine, V. B.; Elsberg, D.

2001-12-01

Bagley Ice Valley, in the St. Elias and Chugach Mountains of south-central Alaska, is an integral part of the largest connected glacierized terrain on the North American continent. From the flow divide between Mt. Logan and Mt. St. Elias, Bagley Ice Valley flows west-northwest for some 90 km down a slope of less than 1o, at widths up to 15 km, to a saddle-gap where it turns south-west to become Bering Glacier. During 4-13 September 2000, an airborne survey of Bagley Ice Valley was performed by Intermap Technologies, Inc., using their Star-3i X-band SAR interferometer. The resulting digital elevation model (DEM) covers an area of 3243 km2. The DEM elevations are orthometric heights, in meters above the EGM96 geoid. The horizontal locations of the 10-m postings are with respect to the WGS84 ellipsoid. On 26 August 2000, 9 to 18 days prior to the Intermap Star-3i survey, a small-aircraft laser altimeter profile was acquired along the central flow line for validation. The laser altimeter data consists of elevations above the WGS84 ellipsoid and orthometric heights above GEOID99-Alaska. Assessment of the accuracy of the Intermap Star-3i DEM was made by comparison of both the DEM orthometric heights and elevations above the WGS84 ellipsoid with the laser altimeter data. Comparison of the orthometric heights showed an average difference of 5.4 +/- 1.0 m (DEM surface higher). Comparison of elevations above the WGS84 ellipsoid showed an average difference of -0.77 +/- 0.93 m (DEM surface lower). This indicates that the X-band Star-3i interferometer was penetrating the glacier surface by an expected small amount. The WGS84 comparison is well within the 3 m RMS accuracy quoted for GT-3 DEM products. Snow accumulation may have occurred, however, on Bagley Ice Valley between 26 August and 4-13 September 2000. This will be estimated using a mass balance model and used to correct the altimeter-derived surface heights. The new DEM of Bagley Ice Valley will provide a reference

Tropical forest heterogeneity from TanDEM-X InSAR and lidar observations in Indonesia

NASA Astrophysics Data System (ADS)

De Grandi, Elsa Carla; Mitchard, Edward

2016-10-01

Fires exacerbated during El Niño Southern Oscillation are a serious threat in Indonesia leading to the destruction and degradation of tropical forests and emissions of CO2 in the atmosphere. Forest structural changes which occurred due to the 1997-1998 El Niño Southern Oscillation in the Sungai Wain Protection Forest (East Kalimantan, Indonesia), a previously intact forest reserve have led to the development of a range of landcover from secondary forest to areas dominated by grassland. These structural differences can be appreciated over large areas by remote sensing instruments such as TanDEM-X and LiDAR that provide information that are sensitive to vegetation vertical and horizontal structure. One-point statistics of TanDEM-X coherence (mean and CV) and LiDAR CHM (mean, CV) and derived metrics such as vegetation volume and canopy cover were tested for the discrimination between 4 landcover classes. Jeffries-Matusita (JM) separability was high between forest classes (primary or secondary forest) and non-forest (grassland) while, primary and secondary forest were not separable. The study tests the potential and the importance of potential of TanDEM-X coherence and LiDAR observations to characterize structural heterogeneity based on one-point statistics in tropical forest but requires improved characterization using two-point statistical measures.

Teaching practical leadership in MIT satellite development class: CASTOR and Exoplanet projects

NASA Astrophysics Data System (ADS)

Babuscia, Alessandra; Craig, Jennifer L.; Connor, Jane A.

2012-08-01

For more than a decade, the Aeronautics and Astronautics Department at MIT has offered undergraduate students the opportunity of conceiving, developing, implementing and operating new spacecraft's missions. During a three term class, junior and senior students experience all the challenges of a true engineering team project: design, analysis, testing, technical documentation development, team management, and leadership. Leadership instruction is an important part of the curricula; through the development of leadership skills, students learn to manage themselves and each other in a more effective way, increasing the overall productivity of the team. Also, a strong leadership education is a key factor in improving the abilities of future engineers to be effective team members and leaders in the companies and agencies in which they will work. However, too often leadership instruction is presented in an abstract way, which does not provide students with suggestions for immediate applicability. As a consequence, students underestimate the potential that leadership education can have on the development of their projects. To counteract that effect, a new approach for teaching "practical" leadership has been developed. This approach is composed of a set of activities developed to improve students' leadership skills in the context of a project. Specifically, this approach has been implemented in the MIT satellite development class. In that class, students experienced the challenges of building two satellites: CASTOR and Exoplanet. These two missions are real space projects which will be launched in the next two years, and which involve cooperation with different entities (MIT, NASA, and Draper). Hence, the MIT faculty was interested in developing leadership activities to improve the productivity of the teams in a short time. In fact, one of the key aspects of the approach proposed is that it can be quickly implemented in a single semester, requiring no more than 4 h of

Ökophysik: Plaudereien über das Leben auf dem Land, im Wasser und in der Luft

NASA Astrophysics Data System (ADS)

Nachtigall, W.

Prof. em. Dr. rer. nat. Werner Nachtigall, geb. 1934, war als Zoophysiologe und Biophysiker Leiter des Zoologischen Instituts der Universität des Saarlandes in Saarbrücken. In Forschung und Ausbildung hat er sich insbesondere mit Aspekten der Technischen Biologie und Bionik befasst und mit seinen Forschergruppen viele Basisdaten insbesondere zur Ökologie, Physiologie und Physik des Fliegens und Schwimmens aber auch zur Stabilität beispielsweise der Gräser erarbeitet. Lebewesen überraschen immer wieder durch ihre "Biodiversität", ihre hochspezifischen Ausgestaltungen und Anpassungen.

BOREAS Regional DEM in Raster Format and AEAC Projection

NASA Technical Reports Server (NTRS)

Knapp, David; Verdin, Kristine; Hall, Forrest G. (Editor)

2000-01-01

This data set is based on the GTOPO30 Digital Elevation Model (DEM) produced by the United States Geological Survey EROS Data Center (USGS EDC). The BOReal Ecosystem-Atmosphere Study (BOREAS) region (1,000 km x 1000 km) was extracted from the GTOPO30 data and reprojected by BOREAS staff into the Albers Equal-Area Conic (AEAC) projection. The pixel size of these data is 1 km. The data are stored in binary, image format files.

Distinct mechanisms of recognizing endosomal sorting complex required for transport III (ESCRT-III) protein IST1 by different microtubule interacting and trafficking (MIT) domains.

PubMed

Guo, Emily Z; Xu, Zhaohui

2015-03-27

The endosomal sorting complex required for transport (ESCRT) machinery is responsible for membrane remodeling in a number of biological processes including multivesicular body biogenesis, cytokinesis, and enveloped virus budding. In mammalian cells, efficient abscission during cytokinesis requires proper function of the ESCRT-III protein IST1, which binds to the microtubule interacting and trafficking (MIT) domains of VPS4, LIP5, and Spartin via its C-terminal MIT-interacting motif (MIM). Here, we studied the molecular interactions between IST1 and the three MIT domain-containing proteins to understand the structural basis that governs pairwise MIT-MIM interaction. Crystal structures of the three molecular complexes revealed that IST1 binds to the MIT domains of VPS4, LIP5, and Spartin using two different mechanisms (MIM1 mode versus MIM3 mode). Structural comparison revealed that structural features in both MIT and MIM contribute to determine the specific binding mechanism. Within the IST1 MIM sequence, two phenylalanine residues were shown to be important in discriminating MIM1 versus MIM3 binding. These observations enabled us to deduce a preliminary binding code, which we applied to provide CHMP2A, a protein that normally only binds the MIT domain in the MIM1 mode, the additional ability to bind the MIT domain of Spartin in the MIM3 mode. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

Distinct Mechanisms of Recognizing Endosomal Sorting Complex Required for Transport III (ESCRT-III) Protein IST1 by Different Microtubule Interacting and Trafficking (MIT) Domains

DOE PAGES

Guo, Emily Z.; Xu, Zhaohui

2015-02-05

The endosomal sorting complex required for transport (ESCRT) machinery is responsible for membrane remodeling in a number of biological processes including multivesicular body biogenesis, cytokinesis, and enveloped virus budding. In mammalian cells, efficient abscission during cytokinesis requires proper function of the ESCRT-III protein IST1, which binds to the microtubule interacting and trafficking (MIT) domains of VPS4, LIP5, and Spartin via its C-terminal MIT-interacting motif (MIM). In this paper, we studied the molecular interactions between IST1 and the three MIT domain-containing proteins to understand the structural basis that governs pairwise MIT-MIM interaction. Crystal structures of the three molecular complexes revealed thatmore » IST1 binds to the MIT domains of VPS4, LIP5, and Spartin using two different mechanisms (MIM1 mode versus MIM3 mode). Structural comparison revealed that structural features in both MIT and MIM contribute to determine the specific binding mechanism. Within the IST1 MIM sequence, two phenylalanine residues were shown to be important in discriminating MIM1 versus MIM3 binding. Finally, these observations enabled us to deduce a preliminary binding code, which we applied to provide CHMP2A, a protein that normally only binds the MIT domain in the MIM1 mode, the additional ability to bind the MIT domain of Spartin in the MIM3 mode.« less

Distinct Mechanisms of Recognizing Endosomal Sorting Complex Required for Transport III (ESCRT-III) Protein IST1 by Different Microtubule Interacting and Trafficking (MIT) Domains*

PubMed Central

Guo, Emily Z.; Xu, Zhaohui

2015-01-01

The endosomal sorting complex required for transport (ESCRT) machinery is responsible for membrane remodeling in a number of biological processes including multivesicular body biogenesis, cytokinesis, and enveloped virus budding. In mammalian cells, efficient abscission during cytokinesis requires proper function of the ESCRT-III protein IST1, which binds to the microtubule interacting and trafficking (MIT) domains of VPS4, LIP5, and Spartin via its C-terminal MIT-interacting motif (MIM). Here, we studied the molecular interactions between IST1 and the three MIT domain-containing proteins to understand the structural basis that governs pairwise MIT-MIM interaction. Crystal structures of the three molecular complexes revealed that IST1 binds to the MIT domains of VPS4, LIP5, and Spartin using two different mechanisms (MIM1 mode versus MIM3 mode). Structural comparison revealed that structural features in both MIT and MIM contribute to determine the specific binding mechanism. Within the IST1 MIM sequence, two phenylalanine residues were shown to be important in discriminating MIM1 versus MIM3 binding. These observations enabled us to deduce a preliminary binding code, which we applied to provide CHMP2A, a protein that normally only binds the MIT domain in the MIM1 mode, the additional ability to bind the MIT domain of Spartin in the MIM3 mode. PMID:25657007

Evaluation of Elevation, Slope and Stream Network Quality of SPOT Dems

NASA Astrophysics Data System (ADS)

El Hage, M.; Simonetto, E.; Faour, G.; Polidori, L.

2012-07-01

Digital elevation models are considered the most useful data for dealing with geomorphology. The quality of these models is an important issue for users. This quality concerns position and shape. Vertical accuracy is the most assessed in many studies and shape quality is often neglected. However, both of them have an impact on the quality of the final results for a particular application. For instance, the elevation accuracy is required for orthorectification and the shape quality for geomorphology and hydrology. In this study, we deal with photogrammetric DEMs and show the importance of the quality assessment of both elevation and shape. For this purpose, we produce several SPOT HRV DEMs with the same dataset but with different template size, that is one of the production parameters from optical images. Then, we evaluate both elevation and shape quality. The shape quality is assessed with in situ measurements and analysis of slopes as an elementary shape and stream networks as a complex shape. We use the fractal dimension and sinuosity to evaluate the stream network shape. The results show that the elevation accuracy as well as the slope accuracy are affected by the template size. Indeed, an improvement of 1 m in the elevation accuracy and of 5 degrees in the slope accuracy has been obtained while changing this parameter. The elevation RMSE ranges from 7.6 to 8.6 m, which is smaller than the pixel size (10 m). For slope, the RMSE depends on the sampling distance. With a distance of 10 m, the minimum slope RMSE is 11.4 degrees. The stream networks extracted from these DEMs present a higher fractal dimension than the reference river. Moreover, the fractal dimension of the extracted networks has a negligible change according to the template size. Finally, the sinuosity of the stream networks is slightly affected by the change of the template size.

DEM study of granular flow around blocks attached to inclined walls

NASA Astrophysics Data System (ADS)

Samsu, Joel; Zhou, Zongyan; Pinson, David; Chew, Sheng

2017-06-01

Damage due to intense particle-wall contact in industrial applications can cause severe problems in industries such as mineral processing, mining and metallurgy. Studying the flow dynamics and forces on containing walls can provide valuable feedback for equipment design and optimising operations to prolong the equipment lifetime. Therefore, solids flow-wall interaction phenomena, i.e. induced wall stress and particle flow patterns should be well understood. In this work, discrete element method (DEM) is used to study steady state granular flow in a gravity-fed hopper like geometry with blocks attached to an inclined wall. The effects of different geometries, e.g. different wall angles and spacing between blocks are studied by means of a 3D DEM slot model with periodic boundary conditions. The findings of this work include (i) flow analysis in terms of flow patterns and particle velocities, (ii) force distributions within the model geometry, and (iii) wall stress vs. model height diagrams. The model enables easy transfer of the key findings to other industrial applications handling granular materials.

Recent Elevation Changes on Bagley Ice Valley, Guyot and Yahtse Glaciers, Alaska, from ICESat Altimetry, Star-3i Airborne, and SRTM Spaceborne DEMs

NASA Astrophysics Data System (ADS)

Muskett, R. R.; Sauber, J. M.; Lingle, C. S.; Rabus, B. T.; Tangborn, W. V.; Echelmeyer, K. A.

2005-12-01

.5 m at 1562 m altitude, -2.6 ± 2.8 m at 1378 m altitude, 6.1 ± 3.5 m at 1142 m altitude, 1.4 ± 12.1 m at 1232 m altitude, -4.0 ± 4.2 m at 250 m to 1217 m altitude, -1.8 ± 3.3 m at 1200 m altitude, and 8.0 ± 6.4 m at 940 m altitude. One ICESat-derived track-to-DEM comparison on Guyot Glacier indicates a preliminary mean elevation change in the 478 m to 1150 m altitude range of -2.8 ± 14.1 m. Results, including additional comparisons to small-aircraft laser altimeter data, with more fully-corrected for estimated snow and ice accumulation / ablation between acquisitions times, will be presented. [Muskett, R.R., C.S. Lingle, W.V. Tangborn, and B.T. Rabus, Multi-decadal elevation changes on Bagley Ice Valley and Malaspina Glacier, Alaska, GRL, 30 (16), 1857, doi:10.1029/2003GL017707, 2003.

Modelling, simulation and verification of the screening process of a swing-bar sieve based on the DEM

NASA Astrophysics Data System (ADS)

Wang, Yang; Yu, Jianqun; Yu, Yajun

2018-05-01

To solve the problems in the DEM simulations of the screening process of a swing-bar sieve, in this paper we propose the real-virtual boundary method to build the geometrical model of the screen deck on a swing-bar sieve. The motion of the swing-bar sieve is modelled by the planer multi-body kinematics. A coupled model of the discrete element method (DEM) with multi-body kinematics (MBK) is presented to simulate the flowing and passing processes of soybean particles on the screen deck. By the comparison of the simulated results with the experimental results of the screening process of the LA-LK laboratory scale swing-bar sieve, the feasibility and validity of the real-virtual boundary method and the coupled DEM-MBK model we proposed in this paper can be verified. This work provides the basis for the optimization design of the swing-bar sieve with circular apertures and complex motion.

Coupling of the Magnetosphere-Ionosphere/Thermosphere and Oxygen Outflow-- MIT Mission

NASA Astrophysics Data System (ADS)

Fu, S.

2017-12-01

The goal of the MIT mission is to understand the coupling of the magnetosphere and ionosphere from the prospective of particles. It will focus on the outflow of the ionosphere particles (mainly oxygen ions) from the Earth, including the acceleration mechanisms of oxygen ions and their relative importance in different regions, the importance of these ions while transferred into the magnetosphere and the roles they played in magnetosphere activities. A constellation of four satellites orbiting at three elliptical orbits will provide the unique opportunities to observed there ions at three different altitude with temporal changes of the flux of these particles and the magnetic field environments. The conceptual design of the spacecraft and a summary of the payload will be presented. The MIT mission was selected as one of the five candidates for the upcoming mission plan in China.

High-quality seamless DEM generation blending SRTM-1, ASTER GDEM v2 and ICESat/GLAS observations

NASA Astrophysics Data System (ADS)

Yue, Linwei; Shen, Huanfeng; Zhang, Liangpei; Zheng, Xianwei; Zhang, Fan; Yuan, Qiangqiang

2017-01-01

The absence of a high-quality seamless global digital elevation model (DEM) dataset has been a challenge for the Earth-related research fields. Recently, the 1-arc-second Shuttle Radar Topography Mission (SRTM-1) data have been released globally, covering over 80% of the Earth's land surface (60°N-56°S). However, voids and anomalies still exist in some tiles, which has prevented the SRTM-1 dataset from being directly used without further processing. In this paper, we propose a method to generate a seamless DEM dataset blending SRTM-1, ASTER GDEM v2, and ICESat laser altimetry data. The ASTER GDEM v2 data are used as the elevation source for the SRTM void filling. To get a reliable filling source, ICESat GLAS points are incorporated to enhance the accuracy of the ASTER data within the void regions, using an artificial neural network (ANN) model. After correction, the voids in the SRTM-1 data are filled with the corrected ASTER GDEM values. The triangular irregular network based delta surface fill (DSF) method is then employed to eliminate the vertical bias between them. Finally, an adaptive outlier filter is applied to all the data tiles. The final result is a seamless global DEM dataset. ICESat points collected from 2003 to 2009 were used to validate the effectiveness of the proposed method, and to assess the vertical accuracy of the global DEM products in China. Furthermore, channel networks in the Yangtze River Basin were also extracted for the data assessment.

[Hepatitis E - More than a Rare Travel-Associated Infectious Disease!

PubMed

Wedemeyer, Heiner

2017-06-01

Übertragungswege  In Deutschland infizieren sich jedes Jahr wahrscheinlich mehr als 300 000 Menschen mit dem Hepatitis-E-Virus (HEV). Die Hepatitis E ist in Mitteleuropa in der Regel eine durch den zoonotischen HEV-Genotyp-3-verursachte autochthone, d. h. lokal erworbene Infektionskrankheit. Der Verzehr von nicht ausreichend erhitztem Schweine- oder Wildfleisch ist ein Hauptrisikofaktor für HEV-Infektionen, Übertragungen des Virus durch Bluttransfusionen sind aber auch möglich. Diagnostik  Bei Immunkompetenten kann die Diagnose einer akuten Hepatitis E mit dem Nachweis von anti-HEV-IgM gestellt werden. Serologische Tests können bei Immunsupprimierten aber falsch-negativ sein, weshalb in diesen Fällen eine HEV-Infektion nur durch den direkten Nachweis des Erregers mittels PCR im Blut oder Stuhl erfolgen sollte. Natürlicher Verlauf  Eine akute Hepatitis E kann bei Patienten mit anderen chronischen Lebererkrankungen zu einem Leberversagen führen. Chronische Verläufe, definiert durch eine Virämie von mind. 3 Monaten, sind bei Organtransplantierten mit immunsuppressiver Medikation beschrieben, können aber auch bei anderen Immundefizienzen auftreten. Eine chronische Hepatitis E kann innerhalb von Monaten zu einer fortgeschrittenen Leberfibrose oder zur Zirrhose führen. Extrahepatische Manifestationen  Extrahepatische Manifestationen können während und nach einer HEV-Infektion auftreten. Insbesondere Guillain-Barré-Syndrome und die neuralgische Schulteramyotrophie sind mit einer Hepatitis E assoziiert worden. Therapie  Ribavirin hat eine antivirale Wirksamkeit gegen HEV. Bei chronischer Hepatitis E sollte die Behandlung für 3 – 6 Monate durchgeführt werden. Therapieversagen und Rückfälle nach Beendigung einer Behandlung sind möglich. Ein Impfstoff gegen HEV ist bisher nur in China zugelassen.

Modeling the motion and orientation of various pharmaceutical tablet shapes in a film coating pan using DEM.

PubMed

Ketterhagen, William R

2011-05-16

Film coating uniformity is an important quality attribute of pharmaceutical tablets. Large variability in coating thickness can limit process efficiency or cause significant variation in the amount or delivery rate of the active pharmaceutical ingredient to the patient. In this work, the discrete element method (DEM) is used to computationally model the motion and orientation of several novel pharmaceutical tablet shapes in a film coating pan in order to predict coating uniformity. The model predictions are first confirmed with experimental data obtained from an equivalent film coating pan using a machine vision system. The model is then applied to predict coating uniformity for various tablet shapes, pan speeds, and pan loadings. The relative effects of these parameters on both inter- and intra-tablet film coating uniformity are assessed. The DEM results show intra-tablet coating uniformity is strongly influenced by tablet shape, and the extent of this can be predicted by a measure of the tablet shape. The tablet shape is shown to have little effect on the mixing of tablets, and thus, the inter-tablet coating uniformity. The pan rotation speed and pan loading are shown to have a small effect on intra-tablet coating uniformity but a more significant impact on inter-tablet uniformity. These results demonstrate the usefulness of modeling in guiding drug product development decisions such as selection of tablet shape and process operating conditions. Copyright © 2011 Elsevier B.V. All rights reserved.

The My Meal Intake Tool (M-MIT): Validity of a Patient Self- Assessment for Food and Fluid Intake at a Single Meal.

PubMed

McCullough, J; Keller, H

2018-01-01

Hospital malnutrition is an under-recognized issue that leads to a variety of adverse outcomes, especially for older adults. Food/fluid intake (FFI) monitoring in hospital can be used to identify those who are improving and those who need further treatment. Current monitoring practices such as calorie counts are impractical for all patients and a patient-completed tool, if valid, could support routine FFI monitoring. The aim of this research was to determine whether the patient-completed My Meal Intake Tool (M-MIT) can accurately represent FFI at a single meal. Cross-sectional, multi-site. Four acute care hospitals in Canada. 120 patients (65+ yrs, adequate cognition). Participants completed M-MIT for a single meal. Food and fluid waste was visually estimated by a research dietitian at each hospital. Sensitivity (Se), specificity (Sp) and overall agreement were calculated for both food and fluid intake by comparing M-MIT and dietitian estimations to determine criterion validity of M-MIT. Patient and research dietitian comments were used to make revisions to the M-MIT. Using a cut-point of ≤50% intake, Se was 76.2% and 61.9% and Sp was 74.0% and 80.5% for solid and fluids respectively (p<0.001). M-MIT identified a greater proportion of participants (37.2%) as having low FFI (≤50%) than dietitians (25.0%), as well as a greater proportion identified with low fluid intake (28.3% vs. 24.6%). Modest revisions were made to improve the tool. This study has demonstrated initial validity of M-MIT for use in older patients with adequate cognition. Use of M-MIT could promote FFI monitoring as a routine practice to make clinical decisions about care.

Precise Determination of the Baseline Between the TerraSAR-X and TanDEM-X Satellites

NASA Astrophysics Data System (ADS)

Koenig, Rolf; Rothacher, Markus; Michalak, Grzegorz; Moon, Yongjin

TerraSAR-X, launched on June 15, 2007, and TanDEM-X, to be launched in September 2009, both carry the Tracking, Occultation and Ranging (TOR) category A payload instrument package. The TOR consists of a high-precision dual-frequency GPS receiver, called Integrated GPS Occultation Receiver (IGOR), for precise orbit determination and atmospheric sounding and a Laser retro-reflector (LRR) serving as target for the global Satellite Laser Ranging (SLR) ground station network. The TOR is supplied by the GeoForschungsZentrum Potsdam (GFZ) Germany, and the Center for Space Research (CSR), Austin, Texas. The objective of the German/US collaboration is twofold: provision of atmospheric profiles for use in numerical weather predictions and climate studies from the occultation data and precision SAR data processing based on precise orbits and atmospheric products. For the scientific objectives of the TanDEM- X mission, i.e., bi-static SAR together with TerraSAR-X, the dual-frequency GPS receiver is of vital importance for the millimeter level determination of the baseline or distance between the two spacecrafts. The paper discusses the feasibility of generating millimeter baselines by the example of GRACE, where for validation the distance between the two GRACE satellites is directly available from the micrometer-level intersatellite link measurements. The distance of the GRACE satellites is some 200 km, the distance of the TerraSAR-X/TanDEM-X formation will be some 200 meters. Therefore the proposed approach is then subject to a simulation of the foreseen TerraSAR-X/TanDEM-X formation. The effect of varying space environmental conditions, of possible phase center variations, multi path, and of varying center of mass of the spacecrafts are evaluated and discussed.

Diagnosis of Dementia in the Specialist Setting: A Comparison Between the Swedish Dementia Registry (SveDem) and the Registry of Dementias of Girona (ReDeGi)

PubMed Central

Garre-Olmo, Josep; Garcia-Ptacek, Sara; Calvó-Perxas, Laia; Turró-Garriga, Oriol; López-Pousa, Secundino; Eriksdotter, Maria

2016-01-01

The aim of this study was to compare the frequency of dementia diagnoses from two dementia registries in Europe. Patients registered between 2007 and 2013 in the Swedish Dementia Registry (SveDem; Sweden) and in the Registry of Dementias of Girona (ReDeGi; North-East of Spain) were selected. We compared sociodemographic data, Mini-Mental State Examination (MMSE) scores, dementia subtype, and medication consumption of 22,384 cases from SveDem and 5,032 cases from ReDeGi. The average age (78.1 years SveDem versus 79.7 years ReDeGi) and the gender (female 58.2% SveDem versus 61.5% ReDeGi) did not greatly differ. MMSE score at diagnosis was higher for SveDem cases (22.1 versus 17.8). Alzheimer’s disease (AD) accounted for the main dementia subtype (36.6% SveDem versus 55.6% ReDeGi). The proportion of vascular dementia (VaD) and mixed dementia was higher in SveDem (18.8% versus 6.4% and 24.9 versus 13.4%), with an odds ratio (OR) and 95% confidence interval (CI) for SveDem relative to the ReDeGi of 3.41 (3.03–3.84) for VaD, and 2.15 (1.97–2.35) for mixed dementia. This was at the expense of a lower frequency of AD in SveDem (OR 0.41; 95% CI 0.39–0.44). Other dementia diagnoses such as frontotemporal dementia or dementia with Lewy bodies did not significantly differ between registries (2.3% versus 2.9%; 1.9 versus 3.1%). Large differences in medication consumption at the time of dementia diagnosis were detected (4.7 treatments SveDem versus 6.8 ReDeGi). Northern and southern European dementia cohorts differ in demographic characteristics, MMSE score at diagnosis, and drug treatment profile. PMID:27392854

Gebrauch von Komplementärmedizin bei Patienten mit metastasierendem Melanom unter Therapie mit Ipilimumab innerhalb einer klinischen Studie.

PubMed

Huebner, Jutta; Mohr, Peter; Simon, Jan-Christoph; Fluck, Michael; Berking, Carola; Zimmer, Lisa; Loquai, Carmen

2016-05-01

In Deutschland wenden 40-90 % aller Krebspatienten Methoden der komplementären and alternativen Medizin (KAM) an. Bis dato gibt es kein Datenmaterial zum Einsatz der KAM bei Melanompatienten. Das Ziel unserer Studie war es, Daten über den Gebrauch, die Informationsquellen und Ziele von Patienten mit metastasierendem Melanom zu erfassen. Einhundertsechsundfünfzig Patienten aus 25 Studienzentren nahmen an der DecOG-MM-PAL Multibasket Studie teil. Die beteiligten Personen wurden auch gebeten, an einer Nebenstudie teilzunehmen, die ihren Gebrauch von KAM erfassen sollte. Dazu wurde während der Behandlung ein standardisierter Fragebogen zu genau festgelegten Zeitpunkten ausgeteilt. Insgesamt gingen 55 Fragebögen von 32 (21 %) Melanompatienten ein. Von diesen gaben 17 (53 %) ein Interesse an KAM an, und sieben (22 %) machten von KAM Gebrauch. Die Hauptinformationsquellen (31 %) waren Familienmitglieder und Freunde, gefolgt von Ärzten (19 %). Die Hauptgründe für die Anwendung von KAM waren die Stärkung des Immunsystems (41 %) und des Körpers (34 %). Nahrungsergänzungsmittel (Vitamine und Spurenelemente) wurden am häufigsten angewendet (28 %). Eine relativ hohe Anzahl an Patienten mit metastasierendem Melanom machte trotz Teilnahme an einer klinischen Studie von KAM Gebrauch. Wechselwirkungen könnten durch biologisch basierte KAM auftreten, und hier besonders bei immunmodulierenden KAM- Strategien. Um Risiken zu vermeiden, sollte die Kommunikation zwischen den Ärzten und den Patienten verbessert werden. © 2016 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

Metacognitive Interpersonal Therapy in group (MIT-G) for young adults with personality disorders: A pilot randomized controlled trial.

PubMed

Popolo, Raffaele; MacBeth, Angus; Canfora, Flaviano; Rebecchi, Daniela; Toselli, Cecilia; Salvatore, Giampaolo; Dimaggio, Giancarlo

2018-04-06

Young adults with personality disorders (PD) other than borderline are in urgent need of validated treatments to help them in managing important life transitions. Therapeutic interventions focused upon social and interpersonal difficulties may facilitate these individuals in maximizing opportunities for employment, forming stable romantic relationships, and belong to social groups. It is also important that they are offered evidence-based, first-line time-limited treatments in order to maximize effectiveness and reduce costs. We developed a 16-session programme of group-based Metacognitive Interpersonal Therapy (MIT-G) including psychoeducation on the main interpersonal motives, an experiential component enabling practice of awareness of mental states; and use of mentalistic knowledge for purposeful problem-solving. We report a feasibility, acceptability, and clinical significance randomized clinical trial. Participants meeting inclusion criteria were randomized to receive MIT-G (n = 10) or waiting list+TAU (n = 10). Dropout rate was low and session attendance high (92.19%). Participants in the MIT-G arm had symptomatic and functional improvements consistent with large effect sizes. In the MIT-G arm similarly large effects were noted for increased capacity to understand mental states and regulate social interactions using mentalistic knowledge. Results were sustained at follow-up. Our findings suggest potential for applying MIT-G in larger samples to further test its effectiveness in reducing PD-related symptoms and problematic social functioning. © 2018 The British Psychological Society.

388. D.E.M., Delineator December 1932 STATE OF CALIFORNIA; DEPARTMENT OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

388. D.E.M., Delineator December 1932 STATE OF CALIFORNIA; DEPARTMENT OF PUBLIC WORKS; SAN FRANCISCO - OAKLAND BAY BRIDGE; SUPERSTRUCTURE - WEST BAY CROSSING; SUSPENDED STRUCTURE; SIDE SPAN TRUSSES AT ANCHORAGES; CONTRACT NO. 6; DRAWING NO. 40 - San Francisco Oakland Bay Bridge, Spanning San Francisco Bay, San Francisco, San Francisco County, CA

Deletion of PdMit1, a homolog of yeast Csg1, affects growth and Ca(2+) sensitivity of the fungus Penicillium digitatum, but does not alter virulence.

PubMed

Zhu, Congyi; Wang, Weili; Wang, Mingshuang; Ruan, Ruoxin; Sun, Xuepeng; He, Meixian; Mao, Cungui; Li, Hongye

2015-04-01

GDP-mannose:inositol-phosphorylceramide (MIPC) and its derivatives are important for Ca(2+) sensitization of Saccharomyces cerevisiae and for the virulence of Candida albicans, but its role in the virulence of plant fungal pathogens remains unclear. In this study, we report the identification and functional characterization of PdMit1, the gene encoding MIPC synthase in Penicillium digitatum, one of the most important pathogens of postharvest citrus fruits. To understand the function of PdMit1, a PdMit1 deletion mutant was generated. Compared to its wild-type control, the PdMit1 deletion mutant exhibited slow radial growth, decreased conidia production and delayed conidial germination, suggesting that PdMit1 is important for the growth of mycelium, sporulation and conidial germination. The PdMit1 deletion mutant also showed hypersensitivity to Ca(2+). Treatment with 250 mmol/l Ca(2+) induced vacuole fusion in the wild-type strain, but not in the PdMit1 deletion mutant. Treatment with 250mmol/lCaCl2 upregulated three Ca(2+)-ATPase genes in the wild-type strain, and this was significantly inhibited in the PdMit1 deletion mutant. These results suggest that PdMit1 may have a role in regulating vacuole fusion and expression of Ca(2+)-ATPase genes by controlling biosynthesis of MIPC, and thereby imparts P. digitatum Ca(2+) tolerance. However, we found that PdMit1 is dispensable for virulence of P. digitatum. Copyright © 2015 Institut Pasteur. Published by Elsevier Masson SAS. All rights reserved.

Smart Meter Rollout: Intelligente Messsysteme als Schnittstelle zum Kunden im Smart Grid und Smart Market

NASA Astrophysics Data System (ADS)

Vortanz, Karsten; Zayer, Peter

Das Gesetz zur Digitalisierung der Energiewende ist verabschiedet. Ab 2017 sind moderne Messeinrichtungen (mME) und intelligente Messsysteme (iMSys) zu verbauen und zu betreiben. Der "deutsche Weg" für die Einführung von Smart Metern sieht einen stufenweisen Rollout sowie ein Höchstmaß an Informations- und Datensicherheit vor. Dabei spielen iMSys und mME eine wichtige Rolle bei der Neugestaltung der intelligenten Netze (Smart Grids) und des neuen Marktmodells (Smart Market). Dieser Beitrag beschäftigt sich mit den neuen Gesetzen, den Marktrollen und ihren Aufgaben, Datenschutz und Datensicherheit, dem iMSys als sichere Lösung, dem sicheren Betrieb von Smart Meter Gateways, Smart Grid - Smart Market, dem Zusammenspiel zwischen reguliertem Bereich und Markt, den Einsatzbereichen der iMSys sowie den Auswirkungen auf Prozesse und Systeme und gibt Handlungsempfehlungen.

Intelligente Messsysteme - Mehrwert für unterschiedliche Stufen der Wertschöpfung

NASA Astrophysics Data System (ADS)

Deppe, Benjamin

Die Veränderung der Energiewirtschaft schreitet kontinuierlich voran - und wird mit Gesetz zur Digitalisierung der Energiewende nicht abgeschlossen sein. Vielmehr steigen die Innovationsgeschwindigkeit und die Erwartungshaltung der Kunden. Dieses Kapitel beschreibt, wie intelligente Messsysteme die Basis für neue Möglichkeiten schaffen und wie sich diese Veränderungen auf die Wertschöpfung auswirken. Der Fokus liegt dabei auf dem Wandel der einzelnen Wertschöpfungsstufen im Verlauf der Liberalisierung des Messwesens und dem seit dem 02.09.2016 verbindlichen Messstellenbetriebsgesetzes. Der Beitrag zeigt auf, wie sich bisher getrennte Wertschöpfungsstufen nunmehr direkt berühren und miteinander interagieren. Deutlich wird dadurch, wie Informationen zu Mehrwert führen können - aber auch, welche Fragen noch zu beantworten sind und welche Hürden es zu überwinden gilt.

MIT Lincoln Laboratory Takes the Mystery Out of Supercomupting

DTIC Science & Technology

2017-01-18

analysis, designing sensors, and developing algorithms. In 2008, the Lincoln demonstrated the largest single problem ever run on a computer using ... computation . As we design and prototype these devices, the use of leading–edge engineering practices have become the de facto standard. This includes...MIT Lincoln Laboratory Takes the Mystery Out of Supercomputing By Dr. Jeremy Kepner 1 The introduction of multicore and manycore processors

The Kubo-Greenwood expression and 2d MIT transport

NASA Astrophysics Data System (ADS)

Castner, Theodore

2010-03-01

The 2d MIT in GaAs heterostructures (p- and n-type)features a mobility that drops continuously as the reduced density x= n/nc-1 is decreased. The Kubo-Greenwood result [1] predicts μ = (eɛh/hnc)α^2(x) where α is a normalized DOS. α(x)is obtained from the data [p-type, Gao et al. [2]; n-type Lilly et al. [3

Constructing a sequence of palaeoDEMs to obtain erosion rates in a drainage basin.N

NASA Astrophysics Data System (ADS)

Castelltort, F. Xavier; Carles Balasch, J.; Cirés, Jordi; Colombo, Ferran

2017-04-01

DEMs made in a present-day drainage basin, considering it as a geomorphic unit, represent the end result of a landscape evolution. This process has had to follow a model of erosion. Trying to establish a conceptual erosion model in landscape evolution represents the first difficulty in constructing a sequence of palaeoDEMs. But if one is able to do it, the result will be easier and believable. The next step to do is to make a catalogue of base level types present in the drainage basin. The list has to include elements with determinate position and elevation (x, y, z) from the centre of the basin until hillslopes. A list of base level types may contain fluvial terrace remnants, erosive surfaces, palaeosols, alluvial covers of glacis, alluvial fans, rockfalls, landslides and scree zones. It is very important to know the spatial and temporal relations between the elements of the list, even if they are disconnected by erosion processes. Relative chronologies have to be set for all elements of the catalogue, and as far as possible absolute chronologies. To do it,it is essential to have established first the spatial relations between them, including those elements that are gone. Moreover, it is also essential to have adapted all the elements to the conceptual erosion model proposed. In this step, it has to be kept in mind that erosion rates can be very different in determinate areas within the same geomorphic unit. Erosion processes are focused in specific zones while other areas are maintained in stability. A good technique to construct a palaeoDEM is to start making, by hand, a map of contour lines. At this point, it is valuable to use the elements' catalogue. The use of those elements belonging to the same palaeosurface will result in a map. Several maps can be obtained from a catalogue. Contour maps can be gridded into a 3D surface by means of a specific application and a set of surfaces will be obtained. Algebraic operations can be done with palaeoDEMs obtaining

Comments on the MIT Assessment of the Mars One Plan

NASA Technical Reports Server (NTRS)

Jones, Harry W.

2015-01-01

The MIT assessment of the Mars One mission plan reveals design assumptions that would cause significant difficulties. Growing crops in the crew chamber produces excessive oxygen levels. The assumed in-situ resource utilization (ISRU) equipment has too low a Technology Readiness Level (TRL). The required spare parts cause a large and increasing launch mass logistics burden. The assumed International Space Station (ISS) Environmental Control and Life Support (ECLS) technologies were developed for microgravity and therefore are not suitable for Mars gravity. Growing food requires more mass than sending food from Earth. The large number of spares is due to the relatively low reliability of ECLS and the low TRL of ISRU. The Mars One habitat design is similar to past concepts but does not incorporate current knowledge. The MIT architecture analysis tool for long-term settlements on the Martian surface includes an ECLS system simulation, an ISRU sizing model, and an analysis of required spares. The MIT tool showed the need for separate crop and crew chambers, the large spare parts logistics, that crops require more mass than Earth food, and that more spares are needed if reliability is lower. That ISRU has low TRL and ISS ECLS was designed for microgravity are well known. Interestingly, the results produced by the architecture analysis tool - separate crop chamber, large spares mass, large crop chamber mass, and low reliability requiring more spares - were also well known. A common approach to ECLS architecture analysis is to build a complex model that is intended to be all-inclusive and is hoped will help solve all design problems. Such models can struggle to replicate obvious and well-known results and are often unable to answer unanticipated new questions. A better approach would be to survey the literature for background knowledge and then directly analyze the important problems.

387. D.E.M., Delineator December 1932 STATE OF CALIFORNIA; DEPARTMENT OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

387. D.E.M., Delineator December 1932 STATE OF CALIFORNIA; DEPARTMENT OF PUBLIC WORKS; SAN FRANCISCO - OAKLAND BAY BRIDGE; SUPERSTRUCTURE - WEST BAY CROSSING; TOWERS 2, 3, 5 & 6; BRACING DETAILS - LOWER DECK; CONTRACT NO. 6; DRAWING NO. 27 - San Francisco Oakland Bay Bridge, Spanning San Francisco Bay, San Francisco, San Francisco County, CA

Research on optimal DEM cell size for 3D visualization of loess terraces

NASA Astrophysics Data System (ADS)

Zhao, Weidong; Tang, Guo'an; Ji, Bin; Ma, Lei

2009-10-01

In order to represent the complex artificial terrains like loess terraces in Shanxi Province in northwest China, a new 3D visual method namely Terraces Elevation Incremental Visual Method (TEIVM) is put forth by the authors. 406 elevation points and 14 enclosed constrained lines are sampled according to the TIN-based Sampling Method (TSM) and DEM Elevation Points and Lines Classification (DEPLC). The elevation points and constrained lines are used to construct Constrained Delaunay Triangulated Irregular Networks (CD-TINs) of the loess terraces. In order to visualize the loess terraces well by use of optimal combination of cell size and Elevation Increment Value (EIV), the CD-TINs is converted to Grid-based DEM (G-DEM) by use of different combination of cell size and EIV with linear interpolating method called Bilinear Interpolation Method (BIM). Our case study shows that the new visual method can visualize the loess terraces steps very well when the combination of cell size and EIV is reasonable. The optimal combination is that the cell size is 1 m and the EIV is 6 m. Results of case study also show that the cell size should be at least smaller than half of both the terraces average width and the average vertical offset of terraces steps for representing the planar shapes of the terraces surfaces and steps well, while the EIV also should be larger than 4.6 times of the terraces average height. The TEIVM and results above is of great significance to the highly refined visualization of artificial terrains like loess terraces.

Structural Fine-Tuning of MIT-Interacting Motif 2 (MIM2) and Allosteric Regulation of ESCRT-III by Vps4 in Yeast.

PubMed

Kojima, Rieko; Obita, Takayuki; Onoue, Kousuke; Mizuguchi, Mineyuki

2016-06-05

The endosomal sorting complex required for transport (ESCRT) facilitates roles in membrane remodeling, such as multivesicular body biogenesis, enveloped virus budding and cell division. In yeast, Vps4 plays a crucial role in intraluminal vesicle formation by disassembling ESCRT proteins. Vps4 is recruited by ESCRT-III proteins to the endosomal membrane through the interaction between the microtubule interacting and trafficking (MIT) domain of Vps4 and the C-terminal MIT-interacting motif (MIM) of ESCRT-III proteins. Here, we have determined the crystal structure of Vps4-MIT in a complex with Vps20, a member of ESCRT-III, and revealed that Vps20 adopts a unique MIM2 conformation. Based on structural comparisons with other known MIM2s, we have refined the consensus sequence of MIM2. We have shown that another ESCRT-III protein, Ist1, binds to Vps4-MIT via its C-terminal MIM1 with higher affinity than Vps2, but lacks MIM2 by surface plasmon resonance. Surprisingly, the Ist1 MIM1 competed with the MIM2 of Vfa1, a regulator of Vps4, for binding to Vps4-MIT, even though these MIMs bind in non-overlapping sites on the MIT. These findings provide insight into the allosteric recognition of MIMs of ESCRT-III by Vps4 and also the regulation of ESCRT machinery at the last step of membrane remodeling. Copyright © 2016 Elsevier Ltd. All rights reserved.

ArcticDEM; A Publically Available, High Resolution Elevation Model of the Arctic

NASA Astrophysics Data System (ADS)

Morin, Paul; Porter, Claire; Cloutier, Michael; Howat, Ian; Noh, Myoung-Jong; Willis, Michael; Bates, Brian; Willamson, Cathleen; Peterman, Kennith

2016-04-01

A Digital Elevation Model (DEM) of the Arctic is needed for a large number of reasons, including: measuring and understanding rapid, ongoing changes to the Arctic landscape resulting from climate change and human use and mitigation and adaptation planning for Arctic communities. The topography of the Arctic is more poorly mapped than most other regions of Earth due to logistical costs and the limits of satellite missions with low-latitude inclinations. A convergence of civilian, high-quality sub-meter stereo imagery; petascale computing and open source photogrammetry software has made it possible to produce a complete, very high resolution (2 to 8-meter posting), elevation model of the Arctic. A partnership between the US National Geospatial-intelligence Agency and a team led by the US National Science Foundation funded Polar Geospatial Center is using stereo imagery from DigitalGlobe's Worldview-1, 2 and 3 satellites and the Ohio State University's Surface Extraction with TIN-based Search-space Minimization (SETSM) software running on the University of Illinois's Blue Water supercomputer to address this challenge. The final product will be a seemless, 2-m posting digital surface model mosaic of the entire Arctic above 60 North including all of Alaska, Greenland and Kamchatka. We will also make available the more than 300,000 individual time-stamped DSM strip pairs that were used to assemble the mosaic. The Arctic DEM will have a vertical precision of better than 0.5m and can be used to examine changes in land surfaces such as those caused by permafrost degradation or the evolution of arctic rivers and floodplains. The data set can also be used to highlight changing geomorphology due to Earth surface mass transport processes occurring in active volcanic and glacial environments. When complete the ArcticDEM will catapult the Arctic from the worst to among the best mapped regions on Earth.

Elastolysen und Hauterkrankungen mit Verlust der elastischen Fasern.

PubMed

Tronnier, Michael

2018-02-01

Die elastischen Fasern sind neben den kollagenen Fasern der wichtigste Bestandteil des Bindegewebsgerüstes der Haut. Eine Verminderung oder ein Verlust der elastischen Fasern ist bei einer Vielzahl von klinisch sich unterschiedlich präsentierenden Erkrankungen, hereditär oder erworben, beschrieben. Bei den Erkrankungen, die mit einer Entzündung einhergehen ist die Elastophagozytose ein wichtiges histologisches Merkmal. Die Therapie der Erkrankungen dieser Gruppe ist grundsätzlich schwierig. © 2018 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

Calibration of micromechanical parameters for DEM simulations by using the particle filter

NASA Astrophysics Data System (ADS)

Cheng, Hongyang; Shuku, Takayuki; Thoeni, Klaus; Yamamoto, Haruyuki

2017-06-01

The calibration of DEM models is typically accomplished by trail and error. However, the procedure lacks of objectivity and has several uncertainties. To deal with these issues, the particle filter is employed as a novel approach to calibrate DEM models of granular soils. The posterior probability distribution of the microparameters that give numerical results in good agreement with the experimental response of a Toyoura sand specimen is approximated by independent model trajectories, referred as `particles', based on Monte Carlo sampling. The soil specimen is modeled by polydisperse packings with different numbers of spherical grains. Prepared in `stress-free' states, the packings are subjected to triaxial quasistatic loading. Given the experimental data, the posterior probability distribution is incrementally updated, until convergence is reached. The resulting `particles' with higher weights are identified as the calibration results. The evolutions of the weighted averages and posterior probability distribution of the micro-parameters are plotted to show the advantage of using a particle filter, i.e., multiple solutions are identified for each parameter with known probabilities of reproducing the experimental response.

Constructing Palaeo-DEMs in landscape evolution: example of the Geren catchment, Turkey

NASA Astrophysics Data System (ADS)

van Gorp, Wouter; Schoorl, Jeroen M.; Veldkamp, Tom; Maddy, Darrel; Demir, Tuncer; Aytac, Serdar

2017-04-01

How to reconstruct the past landscape and how does this influence your modelling results? This is an important paradigma in the soilscape and landscape evolution modelling community. Here an example of Turkey will be presented where a 300 ka LEM simulation requested to the thoroughly think about the initial landscape as an important input. What information can be used to know the morphology of a landscape 300 ka ago? The Geren catchment, a tributary of the upstream Gediz river near Kula, Turkey, has been influenced by base level changes during the Late Pleistocene and Holocene. Different lavaflows have blocked the Gediz and Geren river several times over in the timespan of the last 300 ka -200 Ka and in the recent Holocene. The heavily dissected Geren catchment shows a landscape evolution which is more complex than just a reaction on these base level changes. The steps and inputs of the palaeo DEM reconstruction will be presented and the modelling results will be presented. Keywords: Digital Elevation Model, Palaeo DEMs, Numerical modelling

Holocene palaeoDEMs for lowland coastal and delta plain landscape reconstructions

NASA Astrophysics Data System (ADS)

Cohen, Kim M.; Koster, Kay; Pierik, Harm-Jan; Van der Meulen, Bas; Hijma, Marc; Schokker, Jeroen; Stafleu, Jan

2017-04-01

Geological mapping of Holocene deposits of coastal plains, such as that of The Netherlands can reach high resolution (dense population, diverse applied usage) and good time control (14C dating, archaeology). The next step is then to create time sliced reconstructions for stages in the Holocene, peeling of the subrecent and exposing past relief situation. This includes winding back the history of sea-level rise and delta progradation etc. etc. So far, this has mainly be done as 2D series of landscape maps, or as sea-level curve age-depth plots. In the last decade, academic and applied projects at Utrecht University, TNO Geological Survey of The Netherlands and Deltares have developed palaeoDEMs for the Dutch low lands, that are a third main way of showing coastal plain evolution. Importantly, we produce two types of palaeoDEMs: (1) geological surface mapping using deposit contacts from borehole descriptions (and scripted 3D processing techniques - e.g. Van der Meulen et al. 2013) and (2) palaeogroundwater surfaces, using sea-level and inland water-level index-points (and 3D kriging interpolations - e.g. Koster et al. 2016). The applications for the combined palaeoDEMs range from relative sea-level rise mapping and assessment of variation in rate of GIA across the coastal plain, to quantification of soft soil deformation, to analysis of pre-embankment extreme flood levels. Koster, K., Stafleu, J., & Cohen, K.M. (2016). Generic 3D interpolation of Holocene base-level rise and provision of accommodation space, developed for the Netherlands coastal plain and infilled palaeovalleys. Basin Research. DOI 10.1111/bre.12202 Van der Meulen, M.J., Doornenbal, J.C., Gunnink, J.L., Stafleu, J., Schokker, J., Vernes, R.W., Van Geer, F.C., Van Gessel, S.F., Van Heteren, S., Van Leeuwen, R.J.W. & Bakker, M.A.J. (2013). 3D geology in a 2D country: perspectives for geological surveying in the Netherlands. Netherlands Journal of Geosciences, 92, 217-241. DOI 10.1017/S0016774600000184

Creating high-resolution bare-earth digital elevation models (DEMs) from stereo imagery in an area of densely vegetated deciduous forest using combinations of procedures designed for lidar point cloud filtering

USGS Publications Warehouse

DeWitt, Jessica D.; Warner, Timothy A.; Chirico, Peter G.; Bergstresser, Sarah E.

2017-01-01

For areas of the world that do not have access to lidar, fine-scale digital elevation models (DEMs) can be photogrammetrically created using globally available high-spatial resolution stereo satellite imagery. The resultant DEM is best termed a digital surface model (DSM) because it includes heights of surface features. In densely vegetated conditions, this inclusion can limit its usefulness in applications requiring a bare-earth DEM. This study explores the use of techniques designed for filtering lidar point clouds to mitigate the elevation artifacts caused by above ground features, within the context of a case study of Prince William Forest Park, Virginia, USA. The influences of land cover and leaf-on vs. leaf-off conditions are investigated, and the accuracy of the raw photogrammetric DSM extracted from leaf-on imagery was between that of a lidar bare-earth DEM and the Shuttle Radar Topography Mission DEM. Although the filtered leaf-on photogrammetric DEM retains some artifacts of the vegetation canopy and may not be useful for some applications, filtering procedures significantly improved the accuracy of the modeled terrain. The accuracy of the DSM extracted in leaf-off conditions was comparable in most areas to the lidar bare-earth DEM and filtering procedures resulted in accuracy comparable of that to the lidar DEM.

Inferring sediment connectivity from high-resolution DEMs of Difference

NASA Astrophysics Data System (ADS)

Heckmann, Tobias; Vericat, Damià

2017-04-01

Topographic changes due to the erosion and deposition of bedrock, sediments and soil can be measured by differencing Digital Elevation Models (DEM) acquired at different points in time. So-called morphological sediment budgets can be computed from such DEMs of Difference (DoD) on an areal rather than a point basis. The advent of high-resolution and highly accurate surveying techniques (e.g. LiDAR, SfM), together with recent advances of survey platforms (e.g. UaVs) provides opportunities to improve the spatial and temporal scale (in terms of extent and resolution), the availability and quality of such measurements. Many studies have used DoD to investigate and interpret the spatial pattern of positive and negative vertical differences in terms of erosion and deposition, or of horizontal movement. Vertical differences can be converted to volumes, and negative (erosion) and positive (deposition) volumetric changes aggregated for spatial units (e.g., landforms, hillslopes, river channels) have been used to compute net balances. We argue that flow routing algorithms common in digital terrain analysis provide a means to enrich DoD-based investigations with some information about (potential) sediment pathways - something that has been widely neglected in previous studies. Where the DoD indicates a positive surface change, flow routing delineates the upslope area where the deposited sediment has potentially been derived from. In the downslope direction, flow routing indicates probable downslope pathways of material eroded/detached/entrained where the DoD shows negative surface change. This material has either been deposited along these pathways or been flushed out of the area of investigation. This is a question of sediment connectivity, a property of a system (i.e. a hillslope, a sub-/catchment) that describes its potential to move sediment through itself. The sediment pathways derived from the DEM are related to structural connectivity, while the spatial pattern of (net

A Systems Approach to Healthcare Innovation Using the MIT Hacking Medicine Model.

PubMed

Gubin, Tatyana A; Iyer, Hari P; Liew, Shirlene N; Sarma, Aartik; Revelos, Alex; Ribas, João; Movassaghi, Babak; Chu, Zen M; Khalid, Ayesha N; Majmudar, Maulik D; Lee, Christopher Xiang

2017-07-26

MIT Hacking Medicine is a student, academic, and community-led organization that uses systems-oriented "healthcare hacking" to address challenges around innovation in healthcare. The group has organized more than 80 events around the world that attract participants with diverse backgrounds. These participants are trained to address clinical needs from the perspective of multiple stakeholders and emphasize utility and implementation viability of proposed solutions. We describe the MIT Hacking Medicine model as a potential method to integrate collaboration and training in rapid innovation techniques into academic medical centers. Built upon a systems approach to healthcare innovation, the time-compressed but expertly guided nature of the events could enable more widely accessible preliminary training in systems-level innovation methodology, as well as creating a structured opportunity for interdisciplinary congregation and collaboration. Copyright © 2017 Elsevier Inc. All rights reserved.

Pre-2014 mudslides at Oso revealed by InSAR and multi-source DEM analysis

NASA Astrophysics Data System (ADS)

Kim, J. W.; Lu, Z.; QU, F.

2014-12-01

The landslide is a process that results in the downward and outward movement of slope-reshaping materials including rocks and soils and annually causes the loss of approximately $3.5 billion and tens of casualties in the United States. The 2014 Oso mudslide was an extreme event costing nearly 40 deaths and damaging civilian properties. Landslides are often unpredictable, but in many cases, catastrophic events are repetitive. Historic record in the Oso mudslide site indicates that there have been serial events in decades, though the extent of sliding events varied from time to time. In our study, the combination of multi-source DEMs, InSAR, and time-series InSAR analysis has enabled to characterize the Oso mudslide. InSAR results from ALOS PALSAR show that there was no significant deformation between mid-2006 and 2011. The combination of time-series InSAR analysis and old-dated DEM indicated revealed topographic changes associated the 2006 sliding event, which is confirmed by the difference of multiple LiDAR DEMs. Precipitation and discharge measurements before the 2006 and 2014 landslide events did not exhibit extremely anomalous records, suggesting the precipitation is not the controlling factor in determining the sliding events at Oso. The lack of surface deformation during 2006-2011 and weak correlation between the precipitation and the sliding event, suggest other factors (such as porosity) might play a critical role on the run-away events at this Oso and other similar landslides.

Degradable Implantate: Entwicklungsbeispiele

NASA Astrophysics Data System (ADS)

Ruffieux, Kurt; Wintermantel, Erich

Resorbierbare Implantate werden seit mehreren Jahrzehnten in der Implantologie eingesetzt. Bekannt wurden diese Biomaterialien mit dem Aufkommen von sich selbst auflösenden Nahtfäden auf der Basis von synthetisch hergestellten Polylactiden und Polyglycoliden in den 70er Jahren. In einem nächsten Schritt wurden Implantate wie Platten und Schrauben zur Gewebefixation aus den gleichen Biomaterialien hergestellt.

Tokamak und Stellarator - zwei Wege zur Fusionsenergie: Fusionsforschung

NASA Astrophysics Data System (ADS)

Milch, Isabella

2006-07-01

Im Laufe der Fusionsforschung haben sich zwei Bautypen für ein zukünftiges Kraftwerk als besonders aussichtsreich erwiesen: Tokamak und Stellarator. Mit dem geplanten Tokamak-Experimentalreaktor ITER steht die internationale Fusionsforschung vor der Demonstration eines Energie liefernden Plasmas. Parallel soll die in Greifswald entstehende Forschungsanlage Wendelstein 7-X die Kraftwerkstauglichkeit des alternativen Bauprinzips der Stellaratoren zeigen.

DEM, tide and velocity over sulzberger ice shelf, West Antarctica

USGS Publications Warehouse

Baek, S.; Shum, C.K.; Lee, H.; Yi, Y.; Kwoun, Oh-Ig; Lu, Z.; Braun, Andreas

2005-01-01

Arctic and Antarctic ice sheets preserve more than 77% of the global fresh water and could raise global sea level by several meters if completely melted. Ocean tides near and under ice shelves shifts the grounding line position significantly and are one of current limitations to study glacier dynamics and mass balance. The Sulzberger ice shelf is an area of ice mass flux change in West Antarctica and has not yet been well studied. In this study, we use repeat-pass synthetic aperture radar (SAR) interferometry data from the ERS-1 and ERS-2 tandem missions for generation of a high-resolution (60-m) Digital Elevation Model (DEM) including tidal deformation detection and ice stream velocity of the Sulzberger Ice Shelf. Other satellite data such as laser altimeter measurements with fine foot-prints (70-m) from NASA's ICESat are used for validation and analyses. The resulting DEM has an accuracy of-0.57??5.88 m and is demonstrated to be useful for grounding line detection and ice mass balance studies. The deformation observed by InSAR is found to be primarily due to ocean tides and atmospheric pressure. The 2-D ice stream velocities computed agree qualitatively with previous methods on part of the Ice Shelf from passive microwave remote-sensing data (i.e., LANDSAT). ?? 2005 IEEE.

Capturing Micro-topography of an Arctic Tundra Landscape through Digital Elevation Models (DEMs) Acquired from Various Remote Sensing Platforms

NASA Astrophysics Data System (ADS)

Vargas, S. A., Jr.; Tweedie, C. E.; Oberbauer, S. F.

2013-12-01

The need to improve the spatial and temporal scaling and extrapolation of plot level measurements of ecosystem structure and function to the landscape level has been identified as a persistent research challenge in the arctic terrestrial sciences. Although there has been a range of advances in remote sensing capabilities on satellite, fixed wing, helicopter and unmanned aerial vehicle platforms over the past decade, these present costly, logistically challenging (especially in the Arctic), technically demanding solutions for applications in an arctic environment. Here, we present a relatively low cost alternative to these platforms that uses kite aerial photography (KAP). Specifically, we demonstrate how digital elevation models (DEMs) were derived from this system for a coastal arctic landscape near Barrow, Alaska. DEMs of this area acquired from other remote sensing platforms such as Terrestrial Laser Scanning (TLS), Airborne Laser Scanning, and satellite imagery were also used in this study to determine accuracy and validity of results. DEMs interpolated using the KAP system were comparable to DEMs derived from the other platforms. For remotely sensing acre to kilometer square areas of interest, KAP has proven to be a low cost solution from which derived products that interface ground and satellite platforms can be developed by users with access to low-tech solutions and a limited knowledge of remote sensing.

A Review of Discrete Element Method (DEM) Particle Shapes and Size Distributions for Lunar Soil

NASA Technical Reports Server (NTRS)

Lane, John E.; Metzger, Philip T.; Wilkinson, R. Allen

2010-01-01

As part of ongoing efforts to develop models of lunar soil mechanics, this report reviews two topics that are important to discrete element method (DEM) modeling the behavior of soils (such as lunar soils): (1) methods of modeling particle shapes and (2) analytical representations of particle size distribution. The choice of particle shape complexity is driven primarily by opposing tradeoffs with total number of particles, computer memory, and total simulation computer processing time. The choice is also dependent on available DEM software capabilities. For example, PFC2D/PFC3D and EDEM support clustering of spheres; MIMES incorporates superquadric particle shapes; and BLOKS3D provides polyhedra shapes. Most commercial and custom DEM software supports some type of complex particle shape beyond the standard sphere. Convex polyhedra, clusters of spheres and single parametric particle shapes such as the ellipsoid, polyellipsoid, and superquadric, are all motivated by the desire to introduce asymmetry into the particle shape, as well as edges and corners, in order to better simulate actual granular particle shapes and behavior. An empirical particle size distribution (PSD) formula is shown to fit desert sand data from Bagnold. Particle size data of JSC-1a obtained from a fine particle analyzer at the NASA Kennedy Space Center is also fitted to a similar empirical PSD function.

Bank gully extraction from DEMs utilizing the geomorphologic features of a loess hilly area in China

NASA Astrophysics Data System (ADS)

Yang, Xin; Na, Jiaming; Tang, Guoan; Wang, Tingting; Zhu, Axing

2018-04-01

As one of most active gully types in the Chinese Loess Plateau, bank gullies generally indicate soil loss and land degradation. This study addressed the lack of detailed, large scale monitoring of bank gullies and proposed a semi-automatic method for extracting bank gullies, given typical topographic features based on 5 m resolution DEMs. First, channel networks, including bank gullies, are extracted through an iterative channel burn-in algorithm. Second, gully heads are correctly positioned based on the spatial relationship between gully heads and their corresponding gully shoulder lines. Third, bank gullies are distinguished from other gullies using the newly proposed topographic measurement of "relative gully depth (RGD)." The experimental results from the loess hilly area of the Linjiajian watershed in the Chinese Loess Plateau show that the producer accuracy reaches 87.5%. The accuracy is affected by the DEM resolution and RGD parameters, as well as the accuracy of the gully shoulder line. The application in the Madigou watershed with a high DEM resolution validated the duplicability of this method in other areas. The overall performance shows that bank gullies can be extracted with acceptable accuracy over a large area, which provides essential information for research on soil erosion, geomorphology, and environmental ecology.

DEM generation and tidal deformation detection for sulzberger ice shelf, West Antarctica using SAR interferometry

USGS Publications Warehouse

Baek, S.; Kwoun, Oh-Ig; Bassler, M.; Lu, Z.; Shum, C.K.; Dietrich, R.

2004-01-01

In this study we generated a relative Digital Elevation Model (DEM) over the Sulzberger Ice Shelf, West Antarctica using ERS1/2 synthetic aperture radar (SAR) interferometry data. Four repeat pass differential interferograms are used to find the grounding zone and to classify the study area. An interferometrically derived DEM is compared with laser altimetry profile from ICESat. Standard deviation of the relative height difference is 5.12 m and 1.34 m in total length of the profile and at the center of the profile respectively. The magnitude and the direction of tidal changes estimated from interferogram are compared with those predicted tidal differences from four ocean tide models. Tidal deformation measured in InSAR is -16.7 cm and it agrees well within 3 cm with predicted ones from tide models.

TAF-4 is required for the life extension of isp-1, clk-1 and tpk-1 Mit mutants.

PubMed

Khan, Maruf H; Ligon, Melissa; Hussey, Lauren R; Hufnal, Bryce; Farber, Robert; Munkácsy, Erin; Rodriguez, Amanda; Dillow, Andy; Kahlig, Erynn; Rea, Shane L

2013-10-01

While numerous life-extending manipulations have been discovered in the nematode Caenorhabditis elegans, one that remains most enigmatic is disruption of oxidative phosphorylation. In order to unravel how such an ostensibly deleterious manipulation can extend lifespan, we sought to identify the ensemble of nuclear transcription factors that are activated in response to defective mitochondrial electron transport chain (ETC) function. Using a feeding RNAi approach, we targeted over 400 transcription factors and identified 15 that, when reduced in function, reproducibly and differentially altered the development, stress response, and/or fecundity of isp-1(qm150) Mit mutants relative to wild-type animals. Seven of these transcription factors--AHA-1, CEH-18, HIF-1, JUN-1, NHR-27, NHR-49 and the CREB homolog-1 (CRH-1)-interacting protein TAF-4--were also essential for isp-1 life extension. When we tested the involvement of these seven transcription factors in the life extension of two other Mit mutants, namely clk-1(qm30) and tpk-1(qm162), TAF-4 and HIF-1 were consistently required. Our findings suggest that the Mit phenotype is under the control of multiple transcriptional responses, and that TAF-4 and HIF-1 may be part of a general signaling axis that specifies Mit mutant life extension.

TAF-4 is required for the life extension of isp-1, clk-1 and tpk-1 Mit mutants

PubMed Central

Hufnal, Bryce; Farber, Robert; Munkácsy, Erin; Rodriguez, Amanda; Dillow, Andy; Kahlig, Erynn; Rea, Shane L.

2013-01-01

While numerous life-extending manipulations have been discovered in the nematode Caenorhabditis elegans, one that remains most enigmatic is disruption of oxidative phosphorylation. In order to unravel how such an ostensibly deleterious manipulation can extend lifespan, we sought to identify the ensemble of nuclear transcription factors that are activated in response to defective mitochondrial electron transport chain (ETC) function. Using a feeding RNAi approach, we targeted over 400 transcription factors and identified 15 that, when reduced in function, reproducibly and differentially altered the development, stress response, and/or fecundity of isp-1(qm150) Mit mutants relative to wild-type animals. Seven of these transcription factors – AHA-1, CEH-18, HIF-1, JUN-1, NHR-27, NHR-49 and the CREB homolog-1 (CRH-1)-interacting protein TAF-4 – were also essential for isp-1 life extension. When we tested the involvement of these seven transcription factors in the life extension of two other Mit mutants, namely clk-1(qm30) and tpk-1(qm162), TAF-4 and HIF-1 were consistently required. Our findings suggest that the Mit phenotype is under the control of multiple transcriptional responses, and that TAF-4 and HIF-1 may be part of a general signaling axis that specifies Mit mutant life extension. PMID:24107417

MIT research in telerobotics

NASA Technical Reports Server (NTRS)

Sheridan, T. B.

1987-01-01

Ongoing MIT research in telerobotics (vehicles capable of some autonomous sensing and manipulating, having some remote supervisory control by people) and teleoperation (vehicles for sensing and manipulating which are fully controlled remotely by people) is discussed. The current efforts mix human and artificial intelligence/control. The idea of adjustable impedance at either end of pure master-slave teleoperation, and simultaneous coordinated control of teleoperator/telerobotic systems which have more than six degrees of freedom (e.g., a combined vehicle and arm, each with five or six DOF) are discussed. A new cable-controlled parallel link arm which offers many advantages over conventional arms for space is briefly described. Predictor displays to compensate for time delay in teleoperator loops, the use of state estimation to help human control decisions in space, and ongoing research in supervisory command language are covered. Finally, efforts to build a human flyable real-time dynamic computer-graphic telerobot simulator are described. These projects represent most, but not all, of the telerobotics research in our laboratory, supported by JPL, NASA Ames and NOAA.

DEM modeling of failure mechanisms induced by excavations on the Moon

NASA Astrophysics Data System (ADS)

jiang, mingjing; shen, zhifu; Utili, Stefano

2013-04-01

2D Discrete Element Method (DEM) analyses were performed for excavations supported by retaining walls in lunar environment. The lunar terrain is made of a layer of sand (regolith) which differs from terrestrial sands for two main features: the presence of adhesive attractive forces due to van der Waals interactions and grains being very irregular in shape leading to high interlocking. A simplified contact model based on linear elasticity and perfect plasticity was employed. The contact model includes a moment - relative rotation law to account for high interlocking among grains and a normal adhesion law to account for the van der Waals interactions. Analyses of the excavations were run under both lunar and terrestrial environments. Under lunar environment, gravity is approximately one sixth than the value on Earth and adhesion forces between grains of lunar regolith due to van der Waals interactions are not negligible. From the DEM simulations it emerged that van der Waals interactions may significantly increase the bending moment and deflection of the retaining wall, and the ground displacements. Hence this study indicates that an unsafe estimate of the wall response to an excavation on the Moon would be obtained from physical experiments performed in a terrestrial environment, i.e., considering the effect of gravity but neglecting the van der Waals interactions.

Aerial photography flight quality assessment with GPS/INS and DEM data

NASA Astrophysics Data System (ADS)

Zhao, Haitao; Zhang, Bing; Shang, Jiali; Liu, Jiangui; Li, Dong; Chen, Yanyan; Zuo, Zhengli; Chen, Zhengchao

2018-01-01

The flight altitude, ground coverage, photo overlap, and other acquisition specifications of an aerial photography flight mission directly affect the quality and accuracy of the subsequent mapping tasks. To ensure smooth post-flight data processing and fulfill the pre-defined mapping accuracy, flight quality assessments should be carried out in time. This paper presents a novel and rigorous approach for flight quality evaluation of frame cameras with GPS/INS data and DEM, using geometric calculation rather than image analysis as in the conventional methods. This new approach is based mainly on the collinearity equations, in which the accuracy of a set of flight quality indicators is derived through a rigorous error propagation model and validated with scenario data. Theoretical analysis and practical flight test of an aerial photography mission using an UltraCamXp camera showed that the calculated photo overlap is accurate enough for flight quality assessment of 5 cm ground sample distance image, using the SRTMGL3 DEM and the POSAV510 GPS/INS data. An even better overlap accuracy could be achieved for coarser-resolution aerial photography. With this new approach, the flight quality evaluation can be conducted on site right after landing, providing accurate and timely information for decision making.

Geschichtlicher Überblick

NASA Astrophysics Data System (ADS)

Bölke, Klaus-Peter

Die Nachweise einer schadlosen Ableitung von Abwässern lassen sich bis weit in die Vergangenheit zurückverfolgen. Sie waren bereits zur damaligen Zeit eine Forderung zur Pflege der öffentlichen Reinlichkeit. Der Kanalisationsbau ist auch immer ein Ausdruck der Kultur eines Volkes gewesen. So kann festgestellt werden, dass im Zusammenhang mit der Hochkultur eines Volkes auch der Kanalbau ein vorherrschendes Thema war. Der Kanalbau steht auch in einem engen Zusammenhang mit dem Wasserleitungsbau. Es ist nur logisch, dass dort wo Wasser teilweise aus großer Entfernung herangeführt worden ist, dieses dann nach Gebrauch auch wieder schadlos beseitigt werden musste.

[Leben im Eismeer - Tauchuntersuchungen zur Biologie arktischer Meerespflanzen und Meerestiere

PubMed

Lippert; Karsten; Wiencke

2000-01-01

Die Maske wird nochmals auf Dichtigkeit überprüft, der Knoten der Sicherungsleine mit zwei halben Schlägen fixiert, dann rutscht die Taucherin von der Eiskante in das kalte Wasser. Eine halbe Stunde vergeht, bevor ihr Kopf wieder aus dem Eisloch auftaucht und sie ein großes Sammelnetz nach oben reicht, gefüllt mit verschiedenen Arten von Makroalgen. Obwohl noch große Flächen des Kongsfjordes im arktischen Spitzbergen zugefroren sind und das Festland von einer dicken Schneedecke bedeckt ist, hat unter Wasser in den Algenwäldern bereits der Sommer und damit die Saison der Meeresbiologen begonnen.

Sampling Technique for Robust Odorant Detection Based on MIT RealNose Data

NASA Technical Reports Server (NTRS)

Duong, Tuan A.

2012-01-01

This technique enhances the detection capability of the autonomous Real-Nose system from MIT to detect odorants and their concentrations in noisy and transient environments. The lowcost, portable system with low power consumption will operate at high speed and is suited for unmanned and remotely operated long-life applications. A deterministic mathematical model was developed to detect odorants and calculate their concentration in noisy environments. Real data from MIT's NanoNose was examined, from which a signal conditioning technique was proposed to enable robust odorant detection for the RealNose system. Its sensitivity can reach to sub-part-per-billion (sub-ppb). A Space Invariant Independent Component Analysis (SPICA) algorithm was developed to deal with non-linear mixing that is an over-complete case, and it is used as a preprocessing step to recover the original odorant sources for detection. This approach, combined with the Cascade Error Projection (CEP) Neural Network algorithm, was used to perform odorant identification. Signal conditioning is used to identify potential processing windows to enable robust detection for autonomous systems. So far, the software has been developed and evaluated with current data sets provided by the MIT team. However, continuous data streams are made available where even the occurrence of a new odorant is unannounced and needs to be noticed by the system autonomously before its unambiguous detection. The challenge for the software is to be able to separate the potential valid signal from the odorant and from the noisy transition region when the odorant is just introduced.

Teaching ``The Physics of Energy'' at MIT

NASA Astrophysics Data System (ADS)

Jaffe, Robert

2009-05-01

New physics courses on energy are popping up at colleges and universities across the country. Many require little or no previous physics background, aiming to introduce a broad audience to this complex and critical problem, often augmenting the scientific message with economic and policy discussions. Others are advanced courses, focussing on highly specialized subjects like solar voltaics, nuclear physics, or thermal fluids, for example. About two years ago Washington Taylor and I undertook to develop a course on the ``Physics of Energy'' open to all MIT students who had taken MIT's common core of university level calculus, physics, and chemistry. By avoiding higher level prerequisites, we aimed to attract and make the subject relevant to students in the life sciences, economics, etc. --- as well as physical scientists and engineers --- who want to approach energy issues in a sophisticated and analytical fashion, exploiting their background in calculus, mechanics, and E & M, but without having to take advanced courses in thermodynamics, quantum mechanics, or nuclear physics beforehand. Our object was to interweave teaching the fundamental physics principles at the foundations of energy science with the applications of those principles to energy systems. We envisioned a course that would present the basics of statistical, quantum, and fluid mechanics at a fairly sophisticated level and apply those concepts to the study of energy sources, conversion, transport, losses, storage, conservation, and end use. In the end we developed almost all of the material for the course from scratch. The course debuted this past fall. I will describe what we learned and what general lessons our experience might have for others who contemplate teaching energy physics broadly to a technically sophisticated audience.

Mapping hydrological environments in central Amazonia: ground validation and surface model based on SRTM DEM data corrected for deforestation

NASA Astrophysics Data System (ADS)

Moulatlet, G. M.; Rennó, C. D.; Costa, F. R. C.; Emilio, T.; Schietti, J.

2015-03-01

One of the most important freely available digital elevation models (DEMs) for Amazonia is the one obtained by the Shuttle Radar Topography Mission (SRTM). However, since SRTM tends to represent the vegetation surface instead of the ground surface, the broad use of SRTM DEM as a framework for terrain description in Amazonia is hampered by the presence of deforested areas. We present here two data sets: (1) a deforestation-corrected SRTM DEM for the interfluve between the Purus and Madeira rivers, in central Amazonia, which passed through a careful identification of different environments and has deforestation features corrected by a new method of increasing pixel values of the DEM (Rennó, 2009); and (2) a set of 18 hydrological-topographic descriptors based on the corrected SRTM DEM. Deforestation features are related with the opening of an 800 km road in the central part of the interfluve and occupancy of its vicinity. We used topographic profiles from the pristine forest to the deforested feature to evaluate the recovery of the original canopy coverage by minimizing canopy height variation (corrections ranged from 1 to 38 m). The hydrological-topographic description was obtained by the Height Above the Nearest Drainage (HAND) algorithm, which normalizes the terrain elevation (above sea level) by the elevation of the nearest hydrologically connected drainage. The validation of the HAND data set was done by in situ hydrological description of 110 km of walking trails also available in this data set. The new SRTM DEM expands the applicability of SRTM data for landscape modelling; the data sets of hydrological features based on topographic modelling are undoubtedly appropriate for ecological modelling and an important contribution to environmental mapping of Amazonia. The deforestation-corrected SRTM DEM is available at http://ppbio.inpa.gov.br/knb/metacat/naman.318.3/ppbio; the

Educational Outreach at the MIT Plasma Science and Fusion Center

NASA Astrophysics Data System (ADS)

Rivenberg, Paul; Thomas, Paul

2004-11-01

At the MIT PSFC student and staff volunteers work together to increase the public's knowledge of fusion science and plasma technology. Seeking to generate excitement in young people about science and engineering, the PSFC hosts a number of educational outreach activities and tours throughout the year, including Middle and High School Outreach Days. The PSFC also has an in-school science demonstration program on the theme of magnetism. As ''Mr. Magnet'' Technical Supervisor Paul Thomas brings a truck-load of hands-on demonstrations to K-12 schools, challenging students to help him with experiments. While teaching fundamentals of magnetism and electricity he shows that science is fun for all, and that any student can have a career in science. This year he taught at 75 schools and other events, reaching 30,000 teachers and students. He has expanded his teaching to include an interactive demonstration of plasma, encouraging participants to investigate plasma properties with audiovisual, electromagnetic, and spectroscopic techniques. The PSFC's continuing involvement with the MIT Museum and the Boston Museum of Science also helps familiarize the public with the fourth state of matter.

Seasonal variabilty of surface velocities and ice discharge of Columbia Glacier, Alaska using high-resolution TanDEM-X satellite time series and NASA IceBridge data

NASA Astrophysics Data System (ADS)

Vijay, Saurabh; Braun, Matthias

2014-05-01

Columbia Glacier is a grounded tidewater glacier located on the south coast of Alaska. It has lost half of its volume during 1957-2007, more rapidly after 1980. It is now split into two branches, known as Main/East and West branch due to the dramatic retreat of ~ 23 km and calving of iceberg from its terminus in past few decades. In Alaska, a majority of the mass loss from glaciers is due to rapid ice flow and calving icebergs into tidewater and lacustrine environments. In addition, submarine melting and change in the frontal position can accelerate the ice flow and calving rate. We use time series of high-resolution TanDEM-X stripmap satellite imagery during 2011-2013. The active image of the bistatic TanDEM-X acquisitions, acquired over 11 or 22 day repeat intervals, are utilized to derive surface velocity fields using SAR intensity offset tracking. Due to the short temporal baselines, the precise orbit control and the high-resolution of the data, the accuracies of the velocity products are high. We observe a pronounce seasonal signal in flow velocities close to the glacier front of East/Main branch of Columbia Glacier. Maximum values at the glacier front reach up to 14 m/day were recorded in May 2012 and 12 m/day in June 2013. Minimum velocities at the glacier front are generally observed in September and October with lowest values below 2 m/day in October 2012. Months in between those dates show corresponding increase or deceleration resulting a kind of sinusoidal annual course of the surface velocity at the glacier front. The seasonal signal is consistently decreasing with the distance from the glacier front. At a distance of 17.5 km from the ice front, velocities are reduced to 2 m/day and almost no seasonal variability can be observed. We attribute these temporal and spatial variability to changes in the basal hydrology and lubrification of the glacier bed. Closure of the basal drainage system in early winter leads to maximum speeds while during a fully

High mobility of large mass movements: a study by means of FEM/DEM simulations

NASA Astrophysics Data System (ADS)

Manzella, I.; Lisjak, A.; Grasselli, G.

2013-12-01

Large mass movements, such as rock avalanches and large volcanic debris avalanches are characterized by extremely long propagation, which cannot be modelled using normal sliding friction law. For this reason several studies and theories derived from field observation, physical theories and laboratory experiments, exist to try to explain their high mobility. In order to investigate more into deep some of the processes recalled by these theories, simulations have been run with a new numerical tool called Y-GUI based on the Finite Element-Discrete Element Method FEM/DEM. The FEM/DEM method is a numerical technique developed by Munjiza et al. (1995) where Discrete Element Method (DEM) algorithms are used to model the interaction between different solids, while Finite Element Method (FEM) principles are used to analyze their deformability being also able to explicitly simulate material sudden loss of cohesion (i.e. brittle failure). In particular numerical tests have been run, inspired by the small-scale experiments done by Manzella and Labiouse (2013). They consist of rectangular blocks released on a slope; each block is a rectangular discrete element made of a mesh of finite elements enabled to fragment. These simulations have highlighted the influence on the propagation of block packing, i.e. whether the elements are piled into geometrical ordinate structure before failure or they are chaotically disposed as a loose material, and of the topography, i.e. whether the slope break is smooth and regular or not. In addition the effect of fracturing, i.e. fragmentation, on the total runout have been studied and highlighted.

Internationalizing Practical ChE Education: The M.I.T. Practice School in Japan.

ERIC Educational Resources Information Center

O'Connor, Andrea J.; Kandas, Angelo W.; Natori, Yukikazu; Hatton, T. Alan

1999-01-01

Describes the establishment, benefits, and difficulties of an overseas branch of the Massachusetts Institute of Technology's (MIT) chemical engineering Practice School for student internship study at the Mitsubishi Chemical Corporation's Mizushima Plant in Kurashiki, Japan. (WRM)

Report outlines gender equity progress at MIT

NASA Astrophysics Data System (ADS)

Showstack, Randy

In 1994, 3 tenured women faculty at the Massachusetts Institute of Technology's (MIT) School of Sciences who were concerned about unequal treatment and the small percentage of women faculty there convinced the university to establish a committee to examine the issue.Now 5 years later, and after much research and focus on the issue, working conditions have improved and women faculty at the school total more than 10%, still a low number but a significant increase compared to a total that had been fairly fixed at about 8% for at least the last decade, according to a new report by the Committee on Women Faculty.

SPH-DEM approach to numerically simulate the deformation of three-dimensional RBCs in non-uniform capillaries.

PubMed

Polwaththe-Gallage, Hasitha-Nayanajith; Saha, Suvash C; Sauret, Emilie; Flower, Robert; Senadeera, Wijitha; Gu, YuanTong

2016-12-28

Blood continuously flows through the blood vessels in the human body. When blood flows through the smallest blood vessels, red blood cells (RBCs) in the blood exhibit various types of motion and deformed shapes. Computational modelling techniques can be used to successfully predict the behaviour of the RBCs in capillaries. In this study, we report the application of a meshfree particle approach to model and predict the motion and deformation of three-dimensional RBCs in capillaries. An elastic spring network based on the discrete element method (DEM) is employed to model the three-dimensional RBC membrane. The haemoglobin in the RBC and the plasma in the blood are modelled as smoothed particle hydrodynamics (SPH) particles. For validation purposes, the behaviour of a single RBC in a simple shear flow is examined and compared against experimental results. Then simulations are carried out to predict the behaviour of RBCs in a capillary; (i) the motion of five identical RBCs in a uniform capillary, (ii) the motion of five identical RBCs with different bending stiffness (K b ) values in a stenosed capillary, (iii) the motion of three RBCs in a narrow capillary. Finally five identical RBCs are employed to determine the critical diameter of a stenosed capillary. Validation results showed a good agreement with less than 10% difference. From the above simulations, the following results are obtained; (i) RBCs exhibit different deformation behaviours due to the hydrodynamic interaction between them. (ii) Asymmetrical deformation behaviours of the RBCs are clearly observed when the bending stiffness (K b ) of the RBCs is changed. (iii) The model predicts the ability of the RBCs to squeeze through smaller blood vessels. Finally, from the simulations, the critical diameter of the stenosed section to stop the motion of blood flow is predicted. A three-dimensional spring network model based on DEM in combination with the SPH method is successfully used to model the motion and

Jakobshavn Isbrae, Greenland: DEMs, orthophotos, surface velocities, and ice loss derived from photogrammetric re-analysis of July 1985 repeat aerial photography

NASA Astrophysics Data System (ADS)

Motyka, R.; Fahnestock, M.; Howat, I.; Truffer, M.; Brecher, H.; Luethi, M.

2008-12-01

Jakobshavn Isbrae drains about 7 % of the Greenland Ice Sheet and is the ice sheet's largest outlet glacier. Two sets of high elevation (~13,500 m), high resolution (2 m) aerial photographs of Jakobshavn Isbrae were obtained about two weeks apart during July 1985 (Fastook et al, 1995). These historic photo sets have become increasingly important for documenting and understanding the dynamic state of this outlet stream prior to the rapid retreat and massive ice loss that began in 1998 and continues today. The original photogrammetric analysis of this imagery is summarized in Fastook et al. (1995). They derived a coarse DEM (3 km grid spacing) covering an area of approximately 100 km x 100 km by interpolating several hundred positions determined manually from block-aerial triangulation. We have re-analyzed these photos sets using digital photogrammetry (BAE Socet Set©) and significantly improved DEM quality and resolution (20, 50, and 100 m grids). The DEMs were in turn used to produce high quality orthophoto mosaics. Comparing our 1985 DEM to a DEM we derived from May 2006 NASA ATM measurements showed a total ice volume loss of ~ 105 km3 over the lower drainage area; almost all of this loss has occurred since 1997. Ice stream surface velocities derived from the 1985 orthomosaics showed speeds of 20 m/d on the floating tongue, diminishing to 5 m/d at 50 km further upstream. Velocities have since nearly doubled along the ice stream during its current retreat. Fastook, J.L., H.H. Brecher, and T.J. Hughes, 1995. J.of Glaciol. 11 (137), 161-173.

Grundlagen der zeichnerischen Darstellung

NASA Astrophysics Data System (ADS)

Döring, Peter

Eine Technische Zeichnung muss nach DIN 6774 Teil 1 in der Weise angefertigt werden, dass sie übersichtlich, unmissverständlich, auch in verkleinertem Maßstab lesbar bleibt, kostengünstig reproduzierbar und dauerhaft archivierbar ist. Zu dem Zweck benötigt man entsprechendes Papier und angepasstes Zeichengerät. Heute ist die Anfertigung mit entsprechenden Rechnerprogrammen möglich.

Die nuklearen Anlagen von Hanford (1943-1987) Eine Fallstudie über die Schnittstellen von Physik, Biologie und die US-amerikanische Gesellschaft zur Zeit des Kalten Krieges

NASA Astrophysics Data System (ADS)

Macuglia, Daniele

Die Geschichte des Kalten Krieges eröffnet viele Möglichkeiten, sich näher mit den Schnittstellen von Physik und Biologie während des 20. Jahrhunderts zu befassen. Nicht nur das Unglück in Tschernobyl aus dem Jahr 1986, auch das Beispiel der nuklearen Anlagen in Hanford in den Vereinigten Staaten zeigt die biologischen Folgen von nuklearer Physik.

Graduate Training and Potential Employment for Political Scientists: The MIT Perspective.

ERIC Educational Resources Information Center

Altshuler, Alan

This paper presents ideas on ways to help graduate students in political science to become more marketable for nonacademic positions. It also includes background information on the changing employment market for Ph.D.'s. These ideas were discussed at a 1980 meeting of teachers, graduate students, and recent Ph.D.'s at MIT. The purpose of the…

Aus Wirtschaft und Betrieb. Biomasse: Gewinnung und Verarbeitung mit Profilschal-maschinen

Treesearch

P. Koch

1977-01-01

1963 wurden in den Südstaaten der USA nur 30% der oberund unterirdischen Biomasse der geernteten sog. Southern pines für Schnittholz und Zellstoff verwertet bzw. als getrockneies, gehobletes und abgelängtes Schnittholz oder als Kraftpapier verkauft. Keine der zusammen mit den Kiefern vorkommenden Laubholzarten wurde bisher in nennenswertem Umfan verwertet. Auch heute...

Lava emplacements at Shiveluch volcano (Kamchatka) from June 2011 to September 2014 observed by TanDEM-X SAR-Interferometry

NASA Astrophysics Data System (ADS)

Heck, Alexandra; Kubanek, Julia; Westerhaus, Malte; Gottschämmer, Ellen; Heck, Bernhard; Wenzel, Friedemann

2016-04-01

As part of the Ring of Fire, Shiveluch volcano is one of the largest and most active volcanoes on Kamchatka Peninsula. During the Holocene, only the southern part of the Shiveluch massive was active. Since the last Plinian eruption in 1964, the activity of Shiveluch is characterized by periods of dome growth and explosive eruptions. The recent active phase began in 1999 and continues until today. Due to the special conditions at active volcanoes, such as smoke development, danger of explosions or lava flows, as well as poor weather conditions and inaccessible area, it is difficult to observe the interaction between dome growth, dome destruction, and explosive eruptions in regular intervals. Consequently, a reconstruction of the eruption processes is hardly possible, though important for a better understanding of the eruption mechanism as well as for hazard forecast and risk assessment. A new approach is provided by the bistatic radar data acquired by the TanDEM-X satellite mission. This mission is composed of two nearly identical satellites, TerraSAR-X and TanDEM-X, flying in a close helix formation. On one hand, the radar signals penetrate clouds and partially vegetation and snow considering the average wavelength of about 3.1 cm. On the other hand, in comparison with conventional InSAR methods, the bistatic radar mode has the advantage that there are no difficulties due to temporal decorrelation. By interferometric evaluation of the simultaneously recorded SAR images, it is possible to calculate high-resolution digital elevation models (DEMs) of Shiveluch volcano and its surroundings. Furthermore, the short recurrence interval of 11 days allows to generate time series of DEMs, with which finally volumetric changes of the dome and of lava flows can be determined, as well as lava effusion rates. Here, this method is used at Shiveluch volcano based on data acquired between June 2011 and September 2014. Although Shiveluch has a fissured topography with steep slopes

Detecting Blind Fault with Fractal and Roughness Factors from High Resolution LiDAR DEM at Taiwan

NASA Astrophysics Data System (ADS)

Cheng, Y. S.; Yu, T. T.

2014-12-01

There is no obvious fault scarp associated with blind fault. The traditional method of mapping this unrevealed geological structure is the cluster of seismicity. Neither the seismic event nor the completeness of cluster could be captured by network to chart the location of the entire possible active blind fault within short period of time. High resolution DEM gathered by LiDAR could denote actual terrain information despite the existence of plantation. 1-meter interval DEM of mountain region at Taiwan is utilized by fractal, entropy and roughness calculating with MATLAB code. By jointing these handing, the regions of non-sediment deposit are charted automatically. Possible blind fault associated with Chia-Sen earthquake at southern Taiwan is served as testing ground. GIS layer help in removing the difference from various geological formation, then multi-resolution fractal index is computed around the target region. The type of fault movement controls distribution of fractal index number. The scale of blind fault governs degree of change in fractal index. Landslide induced by rainfall and/or earthquake possesses larger degree of geomorphology alteration than blind fault; special treatment in removing these phenomena is required. Highly weathered condition at Taiwan should erase the possible trace remained upon DEM from the ruptured of blind fault while reoccurrence interval is higher than hundreds of years. This is one of the obstacle in finding possible blind fault at Taiwan.

MiT family translocation renal cell carcinoma.

PubMed

Argani, Pedram

2015-03-01

The MiT subfamily of transcription factors includes TFE3, TFEB, TFC, and MiTF. Gene fusions involving two of these transcription factors have been identified in renal cell carcinoma (RCC). The Xp11 translocation RCCs were first officially recognized in the 2004 WHO renal tumor classification, and harbor gene fusions involving TFE3. The t(6;11) RCCs harbor a specific Alpha-TFEB gene fusion and were first officially recognized in the 2013 International Society of Urologic Pathology (ISUP) Vancouver classification of renal neoplasia. These two subtypes of translocation RCC have many similarities. Both were initially described in and disproportionately involve young patients, though adult translocation RCC may overall outnumber pediatric cases. Both often have unusual and distinctive morphologies; the Xp11 translocation RCCs frequently have clear cells with papillary architecture and abundant psammomatous bodies, while the t(6;11) RCCs frequently have a biphasic appearance with both large and small epithelioid cells and nodules of basement membrane material. However, the morphology of these two neoplasms can overlap, with one mimicking the other. Both of these RCCs underexpress epithelial immunohistochemical markers like cytokeratin and epithelial membrane antigen (EMA) relative to most other RCCs. Unlike other RCCs, both frequently express the cysteine protease cathepsin k and often express melanocytic markers like HMB45 and Melan A. Finally, TFE3 and TFEB have overlapping functional activity as these two transcription factors frequently heterodimerize and bind to the same targets. Therefore, on the basis of clinical, morphologic, immunohistochemical, and genetic similarities, the 2013 ISUP Vancouver classification of renal neoplasia grouped these two neoplasms together under the heading of "MiT family translocation RCC." This review summarizes our current knowledge of these recently described RCCs. Copyright © 2015 Elsevier Inc. All rights reserved.

Introducing the MIT Regional Climate Model (MRCM)

NASA Astrophysics Data System (ADS)

Eltahir, Elfatih A. B.; Winter, Jonathn M.; Marcella, Marc P.; Gianotti, Rebecca L.; Im, Eun-Soon

2013-04-01

During the last decade researchers at MIT have worked on improving the skill of Regional Climate Model version 3 (RegCM3) in simulating climate over different regions through the incorporation of new physical schemes or modification of original schemes. The MIT Regional Climate Model (MRCM) features several modifications over RegCM3 including coupling of Integrated Biosphere Simulator (IBIS), a new surface albedo assignment method, a new convective cloud and rainfall auto-conversion scheme, and a modified boundary layer height and cloud scheme. Here, we introduce the MRCM and briefly describe the major model modifications relative to RegCM3 and their impact on the model performance. The most significant difference relative to the RegCM3 original configuration is coupling the Integrated Biosphere Simulator (IBIS) land-surface scheme (Winter et al., 2009). Based on the simulations using IBIS over the North America, the Maritime Continent, Southwest Asia and West Africa, we demonstrate that the use of IBIS as the land surface scheme results in better representation of surface energy and water budgets in comparison to BATS. Furthermore, the addition of a new irrigation scheme to IBIS makes it possible to investigate the effects of irrigation over any region. Also a new surface albedo assignment method used together with IBIS brings further improvement in simulations of surface radiation (Marcella and Eltahir, 2013). Another important feature of the MRCM is the introduction of a new convective cloud and rainfall auto-conversion scheme (Gianotti and Eltahir, 2013). This modification brings more physical realism into an important component of the model, and succeeds in simulating convective-radiative feedback improving model performance across several radiation fields and rainfall characteristics. Other features of MRCM such as the modified boundary layer height and cloud scheme, and the improvements in the dust emission and transport representations will be discussed.

HELI-DEM portal for geo-processing services

NASA Astrophysics Data System (ADS)

Cannata, Massimiliano; Antonovic, Milan; Molinari, Monia

2014-05-01

HELI-DEM (Helvetia-Italy Digital Elevation Model) is a project developed in the framework of Italy/Switzerland Operational Programme for Trans-frontier Cooperation 2007-2013 whose major aim is to create a unified digital terrain model that includes the alpine and sub-alpine areas between Italy and Switzerland. The partners of the project are: Lombardy Region, Piedmont Region, Polytechnic of Milan, Polytechnic of Turin and Fondazione Politecnico from Italy; Institute of Earth Sciences (SUPSI) from Switzerland. The digital terrain model has been produced by integrating and validating the different elevation data available for the areas of interest, characterized by different reference frame, resolutions and accuracies: DHM at 25 m resolution from Swisstopo, DTM at 20 m resolution from Lombardy Region, DTM at 5 m resolution from Piedmont Region and DTM LiDAR PST-A at about 1 m resolution, that covers the main river bed areas and is produced by the Italian Ministry of the Environment. Further results of the project are: the generation of a unique Italian Swiss geoid with an accuracy of few centimeters (Gilardoni et al. 2012); the establishment of a GNSS permanent network, prototype of a transnational positioning service; the development of a geo-portal, entirely based on open source technologies and open standards, which provides the cross-border DTM and offers some capabilities of analysis and processing through the Internet. With this talk, the authors want to present the main steps of the project with a focus on the HELI-DEM geo-portal development carried out by the Institute of Earth Sciences, which is the access point to the DTM outputted from the project. The portal, accessible at http://geoservice.ist.supsi.ch/helidem, is a demonstration of open source technologies combined for providing access to geospatial functionalities to wide non GIS expert public. In fact, the system is entirely developed using only Open Standards and Free and Open Source Software (FOSS

Windkraftanlagen

NASA Astrophysics Data System (ADS)

Surek, Dominik

Windturbinenanlagen nutzen die kinetische Energie des Windes bei Geschwindigkeiten von c=4 m/s bis 25 m/s in Nabenhöhe des Windrades zur Stromerzeugung. Die oben genannten Windgeschwindigkeiten liegen im Grenzschichtbereich der ebenen Strömung (Abb. 67.1), die bei Höhen von h=100 m bis 1000 m liegen und in Großstädten mit Skylines bis 2000 m. Die größten Windturbinentürme erreichen gegenwärtig Nabenhöhen von h=160 m und Windraddurchmesser von d=130 m, d. h. mit Flügellängen von L=65 m. Die Windturbinen werden vorrangig mit 3 Schaufeln ausgeführt. Windturbinen mit einer und zwei Schaufeln waren Versuchsgeräte. Die Drehzahl von Windturbinen für Leistungen von P_{T}=2 MW betragen n=12 bis 20 min{}^{-1}. Das Windrad entzieht dem Wind mit der Anströmgeschwindigkeit c 1 nach Betz die Geschwindigkeitsdifferenz c2=(2/3) c1. Der Rest der Windgeschwindigkeit wird für die Abströmung des Windes im Leebereich c3=c1/3 benötigt. Durch den Entzug der Geschwindigkeit im Laufrad bläht sich der Abströmdurchmesser auf d3> d1 auf, der bei der Installation von Windturbinen zu beachten ist (Abb. 67.2) [Gasch und Twele(2013)]. Um die Windturbinen bei starkem Wind von c {}1> 25 m/s zu schützen, werden die Laufschaufeln durch Pitch- oder Stall-Anlagen aus dem Wind gedreht, so dass die Strömung an den Schaufeln abreißt und das Windrad in die Ruhestellung gelangt. Bei der Windgeschwindigkeit c1=25 m/s bis 34 m/s wird der Windrotor abgeschaltet. Die zulässige Maximalgeschwindigkeit liegt aus Festigkeitsgründen etwa bei . Die aktive Blattverdrehung (Pitchregelung) stellt eine Blattwinkelregelung dar, wobei die Profilnase in die Anströmung gedreht wird. Sie benötigen für die Drehzahlreduzierung keine mechanische Bremse.

Appeals Court Gives MIT Another Chance to Prove Benefits of Overlap Group.

ERIC Educational Resources Information Center

Jaschik, Scott

1993-01-01

A federal appeals court has given the Massachusetts Institute of Technology another chance to prove in court that the Overlap Group, of which MIT was a member, did not violate antitrust laws. The group of 23 colleges set common financial-aid awards for students admitted to more than one institution. (MSE)

[Osteopathie bei gastroösophagealem Reflux mit Hiatushernie: Ein Fallbericht gemäß der CARE-Leitlinie].

PubMed

Rotter, Gabriele; Brinkhaus, Benno

2017-01-01

Hintergrund: Das Vorhandensein einer Hiatushernie kann das Auftreten einer gastroösophagealen Refluxerkrankung (GERD) als Komplikation bedingen. Konventionelle medizinische Therapiemaßnahmen können zu unerwünschten Ereignissen und Rezidiven führen. Bisher sind die Effekte von osteopathischen Behandlungen bei Hiatushernie und GERD nicht bekannt. Fallbericht: Eine 59-jährige Patientin mit endoskopisch diagnostizierter chronischer Gastritis, GERD und Hiatushernie beklagte einen persistierenden gastroösophagealen Reflux trotz konventionell-medizinischer konservativer Therapie. Die osteopathische Diagnostik ergab eine funktionelle Störung im Bereich des Magens und der Kardia mit einer Beteiligung zugehöriger Reflexzonen. Nach einer osteopathischen Behandlung als individuelle, befundorientierte Therapie ließen die Beschwerden erheblich nach. Die Hiatushernie war nach einer dieser Behandlung endoskopisch nicht mehr nachweisbar. Schlussfolgerungen: Dieser Fallbericht schildert die Symptomreduktion einer GERD nach osteopathischer Behandlung. In der endoskopischen Folgeuntersuchung fand sich die initial diagnostizierte Hiatushernie nicht mehr, diese Befund änderung könnte jedoch auf die unterschiedlichen Untersucher zurückgeführt werden. Prospektive kontrollierte klinische Studien sind notwendig, um den Stellenwert von osteopathischen Behandlungen bei GERD mit Hiatushernie zu untersuchen. © 2017 The Author(s). Published by S. Karger GmbH, Freiburg.

Design and Modeling of a Liquid Lithium LiMIT Loop

NASA Astrophysics Data System (ADS)

Szott, Matthew; Christenson, Michael; Stemmley, Steven; Ahn, Chisung; Andruczyk, Daniel; Ruzic, David

2017-10-01

The use of flowing liquid lithium in plasma facing components has been shown to reduce erosion and thermal stress damage, prolong device lifetime, decrease edge recycling, reduce impurities, and increase plasma performance, all while providing a clean and self-healing surface. The Liquid Metal Infused Trench (LiMIT) system has proven the concept of controlled thermoelectric magnetohydrodynamic-driven lithium flow for use in fusion relevant conditions, through tests at UIUC, HT-7, and Magnum PSI. As the use of liquid lithium in fusion devices progresses, emphasis must now be placed on full systems integration of flowing liquid metal concepts. The LiMIT system will be upgraded to include a full liquid lithium loop, which will pump lithium into the fusion device, utilize TEMHD to drive lithium through the vessel, and remove lithium for filtration and degassing. Flow control concepts recently developed at UIUC - including wetting control, dryout control, and flow velocity control - will be tested in conjunction in order to demonstrate a robust system. Lithium loop system requirements, designs, and modeling work will be presented, along with plans for installation and testing on the HIDRA device at UIUC. This work is supported by DOE/ALPS DE-FG02-99ER54515.

Using high resolution DEMs to assess the effects of roads and trails on hydrological pathways that contribute to gully development

NASA Astrophysics Data System (ADS)

Sidle, R. C.; Jarihani, B.

2017-12-01

Dry savannas of northern Queensland, Australia experience severe gully erosion, particularly areas that have been heavily grazed. Field surveys have also noted the influence of unpaved roads and cattle trails on concentrating storm runoff into gully systems. To better quantify the effect of these roads and trails we use high resolution digital elevation models (DEMs) to develop indices of hydrological connectivity (IC) throughout drainage areas above and downstream of gully systems. High resolution (0.5m) DEMs from LiDAR were used to extract road and trail networks and drone-based very high resolution (0.1m) DEMs were used to extract cattle trials. IC is a function of the ratio of upslope to downslope sediment routing functions, which are based on upslope area, mean slope gradient, a weighting factor related to impedance to overland flow, and flow path distance (for the downstream function). Maps of IC within the heavily grazed Weany Creek catchment (13 km2) of northeast Queensland show that existing roads can increase hydrologic connectivity to gully systems. Furthermore, by adding roads and cattle trails into existing DEMs, we show how the extent and location of these curvilinear features affect overland flow concentration. Our findings can inform important hydrogeomorphic issues such as which gullies will likely headcut or expand and where new gullies may arise. Our analysis can also contribute to better management practices for grazing and road location.

Regional climate projection of the Maritime Continent using the MIT Regional Climate Model

NASA Astrophysics Data System (ADS)

IM, E. S.; Eltahir, E. A. B.

2014-12-01

Given that warming of the climate system is unequivocal (IPCC AR5), accurate assessment of future climate is essential to understand the impact of climate change due to global warming. Modelling the climate change of the Maritime Continent is particularly challenge, showing a high degree of uncertainty. Compared to other regions, model agreement of future projections in response to anthropogenic emission forcings is much less. Furthermore, the spatial and temporal behaviors of climate projections seem to vary significantly due to a complex geographical condition and a wide range of scale interactions. For the fine-scale climate information (27 km) suitable for representing the complexity of climate change over the Maritime Continent, dynamical downscaling is performed using the MIT regional climate model (MRCM) during two thirty-year period for reference (1970-1999) and future (2070-2099) climate. Initial and boundary conditions are provided by Community Earth System Model (CESM) simulations under the emission scenarios projected by MIT Integrated Global System Model (IGSM). Changes in mean climate as well as the frequency and intensity of extreme climate events are investigated at various temporal and spatial scales. Our analysis is primarily centered on the different behavior of changes in convective and large-scale precipitation over land vs. ocean during dry vs. wet season. In addition, we attempt to find the added value to downscaled results over the Maritime Continent through the comparison between MRCM and CESM projection. Acknowledgements.This research was supported by the National Research Foundation Singapore through the Singapore MIT Alliance for Research and Technology's Center for Environmental Sensing and Modeling interdisciplinary research program.

An automated, open-source pipeline for mass production of digital elevation models (DEMs) from very-high-resolution commercial stereo satellite imagery

NASA Astrophysics Data System (ADS)

Shean, David E.; Alexandrov, Oleg; Moratto, Zachary M.; Smith, Benjamin E.; Joughin, Ian R.; Porter, Claire; Morin, Paul

2016-06-01

We adapted the automated, open source NASA Ames Stereo Pipeline (ASP) to generate digital elevation models (DEMs) and orthoimages from very-high-resolution (VHR) commercial imagery of the Earth. These modifications include support for rigorous and rational polynomial coefficient (RPC) sensor models, sensor geometry correction, bundle adjustment, point cloud co-registration, and significant improvements to the ASP code base. We outline a processing workflow for ˜0.5 m ground sample distance (GSD) DigitalGlobe WorldView-1 and WorldView-2 along-track stereo image data, with an overview of ASP capabilities, an evaluation of ASP correlator options, benchmark test results, and two case studies of DEM accuracy. Output DEM products are posted at ˜2 m with direct geolocation accuracy of <5.0 m CE90/LE90. An automated iterative closest-point (ICP) co-registration tool reduces absolute vertical and horizontal error to <0.5 m where appropriate ground-control data are available, with observed standard deviation of ˜0.1-0.5 m for overlapping, co-registered DEMs (n = 14, 17). While ASP can be used to process individual stereo pairs on a local workstation, the methods presented here were developed for large-scale batch processing in a high-performance computing environment. We are leveraging these resources to produce dense time series and regional mosaics for the Earth's polar regions.

Two Preliminary SRTM DEMs Within the Amazon Basin

NASA Astrophysics Data System (ADS)

Alsdorf, D.; Hess, L.; Melack, J.; Dunne, T.; Mertes, L.; Ballantine, A.; Biggs, T.; Holmes, K.; Sheng, Y.; Hendricks, G.

2002-12-01

Digital topography provides important measures, such as hillslope lengths and flow path networks, for understanding hydrologic and geomorphic processes (e.g., runoff response to land use change and floodplain inundation volume). Two preliminary Shuttle Radar Topography Mission digital elevation models of Manaus (1S to 5S and 59W to 63W) and Rondonia (9S to 12S and 61W to 64W) were received from NASA JPL in August 2002. The "PI Processor" produced these initial DEM segments and we are using them to assess the initial accuracy of the interferometrically derived heights and for hydrologic research. The preliminary SRTM derived absolute elevations across the Amazon floodplain in the Cabaliana region generally range from 5 to 15 m with reported errors of 1 to 3 m. This region also includes some preliminary elevations that are erroneously negative. However, topographic contours on 1:100,000 scale quadrangles of 1978 to 1980 vintage indicate elevations of 20 to 30 m. Because double-bounce travel paths are possible over the sparsely vegetated and very-flat 2400 sq-km water surface of the Balbina reservoir near Manaus, it serves to identify the relative accuracy of the SRTM heights. Here, cell-to-cell height changes are generally 0 to 1 m and changes across a ~100 km transect rarely exceed 3 m. Reported errors throughout the transect range from 1 to 2 m with some errors up to 5 m. Deforestation in Rondonia is remarkably clear in the C-band DEM where elevations are recorded from the canopy rather than bare earth. Here, elevation changes are ~30 m (with reported 1 to 2 m errors) across clear-cut areas. Field derived canopy heights are in agreement with this change. Presently, we are deriving stream networks in the Amazon floodplain for comparison with our previous network extraction from JERS-1 SAR mosaics and for hydrologic modeling.

Sicherung mathematischer Grundkompetenzen am Beispiel des österreichischen Zentralabiturs

NASA Astrophysics Data System (ADS)

Peschek, Werner

Der österreichische Nationalrat (Parlament) hat im Sommer 2009 eine Neugestaltung der Reifeprüfung (Abitur) beschlossen; die wesentlichste Änderung besteht darin, dass die Aufgabenstellungen der für alle Schülerinnen und Schüler verbindlichen schriftlichen Reifeprüfung (sRP) in den Fächern Deutsch, Mathematik und einer lebenden Fremdsprache zentral und nicht wie bisher durch die jeweilige Klassenlehrerin bzw. den Klassenlehrer erfolgen. Für die Allgemeinbildenden Höheren Schulen ("Gymnasien") soll diese neue Regelung ab dem Schuljahr 2013/14 gelten, für die Berufsbildenden Höheren Schulen (u. a. höhere technische oder kaufmännische Schulen mit Abitur) ab dem Schuljahr 2014/15.

Turbulenzübergang in der Rohrströmung: Die Lösung eines alten Rätsels

NASA Astrophysics Data System (ADS)

Eckhardt, Bruno; Hof, Björn; Faisst, Holger

2006-09-01

Die Strömung von Flüssigkeiten und Gasen durch eine Röhre kann zwei Zustände annehmen. Einer ist laminar, also gleichmäßig geordnet, einer ist zeitlich-räumlich verwirbelt und turbulent. Mit dem Übergang zur Turbulenz nimmt der Strömungswiderstand drastisch zu. Vor etwa 120 Jahren beschrieb Osborne Reynolds bereits das Verhalten der Rohrströmung sehr genau. Er beobachtete, dass der Turbulenzübergang sehr empfindlich von äußeren Störungen abhängt, was bislang rätselhaft blieb. Dieses Rätsel konnte nun mit einer Kombination aus Computerstudien, Konzepten aus der nichtlinearen Dynamik und speziell entwickelten Experimenten gelöst werden.

Digitalisierung des Bösen: Energiewirtschaft als Cyberopfer

NASA Astrophysics Data System (ADS)

Bartsch, Michael; Frey, Stefanie

Die Energieversorgung ist eine kritische Infrastruktur, da alle anderen Sektoren von der Stromversorgung abhängig sind und eine Störung katastrophale Auswirkungen mit unvorhersehbaren Kaskadeneffekten mit sich bringen würde. Das oberste Ziel der Betreiber ist daher sicherzustellen, dass Maßnahmen für eine störungsfreie Stromversorgung ergriffen werden. Cyberangriffe stellen ein hohes Risiko für die Energieversorgung dar. Dabei kann die Energiewirtschaft von Massenphänomenen wie Cybercrime betroffen sein, aber auch Gegenstand von technisch komplexer Cybersabotage werden, wie bei dem Angriff Ende 2015 auf einen ukrainischen Energieversorger. Die Stromversorgung fiel für mehrere Stunden aus und hatte weitreichende Auswirkungen für die Bevölkerung und Unternehmen.

Numerical slope stability simulations of chasma walls in Valles Marineris/Mars using a distinct element method (dem).

NASA Astrophysics Data System (ADS)

Imre, B.

2003-04-01

NUMERICAL SLOPE STABILITY SIMULATIONS OF CHASMA WALLS IN VALLES MARINERIS/MARS USING A DISTINCT ELEMENT METHOD (DEM). B. Imre (1) (1) German Aerospace Center, Berlin Adlershof, bernd.imre@gmx.net The 8- to 10-km depths of Valles Marineris (VM) offer excellent views into the upper Martian crust. Layering, fracturing, lithology, stratigraphy and the content of volatiles have influenced the evolution of the Valles Marineris wallslopes. But these parameters also reflect the development of VM and its wall slopes. The scope of this work is to gain understanding in these parameters by back-simulating the development of wall slopes. For that purpose, the two dimensional Particle Flow Code PFC2D has been chosen (ITASCA, version 2.00-103). PFC2D is a distinct element code for numerical modelling of movements and interactions of assemblies of arbitrarily sized circular particles. Particles may be bonded together to represent a solid material. Movements of particles are unlimited. That is of importance because results of open systems with numerous unknown variables are non-unique and therefore highly path dependent. This DEM allows the simulation of whole development paths of VM walls what makes confirmation of the model more complete (e.g. Oreskes et al., Science 263, 1994). To reduce the number of unknown variables a proper (that means as simple as possible) field-site had to be selected. The northern wall of eastern Candor Chasma has been chosen. This wall is up to 8-km high and represents a significant outcrop of the upper Martian crust. It is quite uncomplex, well-aligned and of simple morphology. Currently the work on the model is at the stage of performing the parameter study. Results will be presented via poster by the EGS-Meeting.

Theoretical and Experimental Evidence for a Nodal Energy Gap in MgB2

DTIC Science & Technology

2017-02-17

1   Theoretical and Experimental Evidence for a Nodal Energy Gap in MgB2 Y. Dan Agassia and Daniel E. Oatesb aConsultant, Jerusalem, Israel bMIT...surface impedance and intermodulation distortion in high-quality thin films. We briefly review experimental evidence in support of our hypothesis and...demonstrates, this experimental evidence agrees with the l = 6 hypothesis, while inconsistent with s-wave symmetry. To give the l = 6 hypothesis a

Evaluation of the MIT-Scan-T2 for non-destructive PCC pavement thickness determination.

DOT National Transportation Integrated Search

2008-07-01

The MIT-Scan-T2 device is marketed as a non-destructive way to determine pavement thickness on both : HMA and PCC pavements. PCC pavement thickness determination is an important incentivedisincentive : measurement for the Iowa DOT and contractors. Th...

Evaluation of microRNAs − 208 and 133a/b as differential biomarkers of acute cardiac and skeletal muscle toxicity in rats

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calvano, Jacqueline, E-mail: Jacqueline.Calvano@bm

Conventional circulating biomarkers of cardiac and skeletal muscle (SKM) toxicity lack specificity and/or have a short half-life. MicroRNAs (miRNAs) are currently being assessed as biomarkers of tissue injury based on their long half-life in blood and selective expression in certain tissues. To assess the utility of miRNAs as biomarkers of cardiac and SKM injury, male Sprague–Dawley rats received a single dose of isoproterenol (ISO); metaproterenol (MET); allylamine (AAM); mitoxantrone (MIT); acetaminophen (APAP) or vehicle. Blood and tissues were collected from rats in each group at 4, 24 and 48 h. ISO, MET, and AAM induced cardiac and SKM lesions andmore » APAP induced liver specific lesions. There was no evidence of tissue injury with MIT by histopathology. Serum levels of candidate miRNAs were compared to conventional serum biomarkers of SKM/cardiac toxicity. Increases in heart specific miR-208 only occurred in rats with cardiac lesions alone and were increased for a longer duration than cardiac troponin and FABP3 (cardiac biomarkers). ISO, MET and AAM induced increases in MyL3 and skeletal muscle troponin (sTnl) (SKM biomarkers). MIT induced large increases in sTnl indicative of SKM toxicity, but sTnl levels were also increased in APAP-treated rats that lacked SKM toxicity. Serum levels of miR-133a/b (enriched in cardiac and SKM) increased following ISO, MET, AAM and MIT treatments but were absent in APAP-treated rats. Our results suggest that miR-133a/b are sensitive and specific markers of SKM and cardiac toxicity and that miR-208 used in combination with miR-133a/b can be used to differentiate cardiac from SKM toxicity. - Highlights: • MiR-208 is specifically expressed in rat hearts. • MiR-133a/b are enriched in rat cardiac/skeletal muscle. • MiR-133a/b are sensitive and specific markers of muscle/cardiac toxicity. • MiR-208 can be used to differentiate cardiac toxicity from skeletal muscle toxicity.« less

The MIT high resolution X-ray spectroscopy instruments on AXAF

NASA Technical Reports Server (NTRS)

Canizares, C. R.; Dewey, D.; Galton, E. B.; Markert, T. H.; Smith, Henry I.; Schattenburg, M. L.; Woodgate, B. E.; Jordan, S.

1992-01-01

The general design and performance characteristics of MIT's two dispersive spectrometers, the Bragg Crystal Spectrometer (BCS) and the High Energy Transmission Grating Spectrometer (HETG), now being developed for the Advanced X-ray Astrophysics Facility (AXAF), are described. Particular attention is given to the development of the critical technologies incorporated into these instruments, including BCS diffractors, imaging gas flow proportional counters, and grating elements for the HETG. The principal stages and the current status of the developments are reviewed.

MIT-KSC space life sciences telescience testbed

NASA Technical Reports Server (NTRS)

1989-01-01

A Telescience Life Sciences Testbed is being developed. The first phase of this effort consisted of defining the experiments to be performed, investigating the various possible means of communication between KSC and MIT, and developing software and hardware support. The experiments chosen were two vestibular sled experiments: a study of ocular torsion produced by Y axis linear acceleration, based on the Spacelab D-1 072 Vestibular Experiment performed pre- and post-flight at KSC; and an optokinetic nystagmus (OKN)/linear acceleration interaction experiment. These two experiments were meant to simulate actual experiments that might be performed on the Space Station and to be representative of space life sciences experiments in general in their use of crew time and communications resources.

Comparative costs of the Mouse Inoculation Test (MIT) and Virus Isolation in Cell Culture (VICC) for use in rabies diagnosis in Brazil.

PubMed

Bones, Vanessa C; Gameiro, Augusto H; Castilho, Juliana G; Molento, Carla F M

2015-05-01

The decision to use laboratory animals rather than in vitro methods is frequently based on the financial costs involved, so the objective of our study was to compare the costs of performing the Mouse Inoculation Test (MIT) and Virus Isolation in Cell Culture (VICC) for use in rabies diagnosis in Brazil. Based on observations of laboratory routines at the Pasteur Institute, São Paulo, we listed the fixed cost (FC) and variable cost (VC) items necessary to perform both tests. Considering that 200 MITs are equivalent to 350 VICC assays, in terms of facilities and staff-hours needed per month, we calculated, for both tests, the average total cost per sample, the costs of the implementation of the laboratory structure, and the costs of routine use. With regard to absolute values, the total cost was mainly influenced by FC items, as they represented 60% of the cost for the MIT and 86% of the cost for VICC. A sample analysed by the MIT costs around 205% more than one analysed by using VICC. The MIT costs 74% and 406% more than VICC, when implementation costs and routine use per month, respectively, are taken into account. Our results can assist in the resolution of costing disputes that could hinder the replacement of animals for rabies diagnosis in Brazil. The method demonstrated here might also be useful for cost comparisons in other situations where animal use still continues when validated alternatives exist. 2015 FRAME.

DEM simulation of granular flows in a centrifugal acceleration field

NASA Astrophysics Data System (ADS)

Cabrera, Miguel Angel; Peng, Chong; Wu, Wei

2017-04-01

The main purpose of mass-flow experimental models is abstracting distinctive features of natural granular flows, and allow its systematic study in the laboratory. In this process, particle size, space, time, and stress scales must be considered for the proper representation of specific phenomena [5]. One of the most challenging tasks in small scale models, is matching the range of stresses and strains among the particle and fluid media observed in a field event. Centrifuge modelling offers an alternative to upscale all gravity-driven processes, and it has been recently employed in the simulation of granular flows [1, 2, 3, 6, 7]. Centrifuge scaling principles are presented in Ref. [4], collecting a wide spectrum of static and dynamic models. However, for the case of kinematic processes, the non-uniformity of the centrifugal acceleration field plays a major role (i.e., Coriolis and inertial effects). In this work, we discuss a general formulation for the centrifugal acceleration field, implemented in a discrete element model framework (DEM), and validated with centrifuge experimental results. Conventional DEM simulations relate the volumetric forces as a function of the gravitational force Gp = mpg. However, in the local coordinate system of a rotating centrifuge model, the cylindrical centrifugal acceleration field needs to be included. In this rotating system, the centrifugal acceleration of a particle depends on the rotating speed of the centrifuge, as well as the position and speed of the particle in the rotating model. Therefore, we obtain the formulation of centrifugal acceleration field by coordinate transformation. The numerical model is validated with a series of centrifuge experiments of monodispersed glass beads, flowing down an inclined plane at different acceleration levels and slope angles. Further discussion leads to the numerical parameterization necessary for simulating equivalent granular flows under an augmented acceleration field. The premise of

Extraction of multi-scale landslide morphological features based on local Gi* using airborne LiDAR-derived DEM

NASA Astrophysics Data System (ADS)

Shi, Wenzhong; Deng, Susu; Xu, Wenbing

2018-02-01

For automatic landslide detection, landslide morphological features should be quantitatively expressed and extracted. High-resolution Digital Elevation Models (DEMs) derived from airborne Light Detection and Ranging (LiDAR) data allow fine-scale morphological features to be extracted, but noise in DEMs influences morphological feature extraction, and the multi-scale nature of landslide features should be considered. This paper proposes a method to extract landslide morphological features characterized by homogeneous spatial patterns. Both profile and tangential curvature are utilized to quantify land surface morphology, and a local Gi* statistic is calculated for each cell to identify significant patterns of clustering of similar morphometric values. The method was tested on both synthetic surfaces simulating natural terrain and airborne LiDAR data acquired over an area dominated by shallow debris slides and flows. The test results of the synthetic data indicate that the concave and convex morphologies of the simulated terrain features at different scales and distinctness could be recognized using the proposed method, even when random noise was added to the synthetic data. In the test area, cells with large local Gi* values were extracted at a specified significance level from the profile and the tangential curvature image generated from the LiDAR-derived 1-m DEM. The morphologies of landslide main scarps, source areas and trails were clearly indicated, and the morphological features were represented by clusters of extracted cells. A comparison with the morphological feature extraction method based on curvature thresholds proved the proposed method's robustness to DEM noise. When verified against a landslide inventory, the morphological features of almost all recent (< 5 years) landslides and approximately 35% of historical (> 10 years) landslides were extracted. This finding indicates that the proposed method can facilitate landslide detection, although the cell

Mapping boreal forest biomass from a SRTM and TanDEM-X based on canopy height model and Landsat spectral indices

NASA Astrophysics Data System (ADS)

Sadeghi, Yaser; St-Onge, Benoît; Leblon, Brigitte; Prieur, Jean-François; Simard, Marc

2018-06-01

We propose a method for mapping above-ground biomass (AGB) (Mg ha-1) in boreal forests based predominantly on Landsat 8 images and on canopy height models (CHM) generated using interferometric synthetic aperture radar (InSAR) from the Shuttle Radar Topographic Mission (SRTM) and the TanDEM-X mission. The original SRTM digital elevation model (DEM) was corrected by modelling the respective effects of landform and land cover on its errors and then subtracted from a TanDEM-X DSM to produce a SAR CHM. Among all the landform factors, the terrain curvature had the largest effect on SRTM elevation errors, with a r2 of 0.29. The NDSI was the best predictor of the residual SRTM land cover error, with a r2 of 0.30. The final SAR CHM had a RMSE of 2.45 m, with a bias of 0.07 m, compared to a lidar-based CHM. An AGB prediction model was developed based on a combination of the SAR CHM, TanDEM-X coherence, Landsat 8 NDVI, and other vegetation indices of RVI, DVI, GRVI, EVI, LAI, GNDVI, SAVI, GVI, Brightness, Greenness, and Wetness. The best results were obtained using a Random forest regression algorithm, at the stand level, yielding a RMSE of 26 Mg ha-1 (34% of average biomass), with a r2 of 0.62. This method has the potential of creating spatially continuous biomass maps over entire biomes using only spaceborne sensors and requiring only low-intensity calibration.

First Observations of a Stellar Occultation by KBO (50000) Quaoar from MIT's George R. Wallace, Jr., Astrophysical Observatory

NASA Astrophysics Data System (ADS)

Sallum, Stephanie; Brothers, T.; Elliot, J. L.; Person, M. J.; Bosh, A. S.; Zangari, A.; Zuluaga, C.; Levine, S.; Bright, L.; Sheppard, S.; Tilleman, T.

2011-05-01

Here we report the first recorded observations of a stellar occultation by Kuiper Belt Object (KBO) (50000) Quaoar. We detected a single-chord stellar occultation by Quaoar of a magnitude 16.2 star designated 26029635 UCAC2 (2MASS ID 1275509401), which occurred on 11 February 2011 UT. The prediction of the occultation was made using long baseline astrometric observations of Quaoar from several sites as part of the MIT Planetary Astronomy Laboratory's continuing effort to improve KBO positions for occultation prediction. The successful observations were made with a Celestron C14 0.36 m telescope and an SBIG STL-1001E CCD camera on a Paramount ME robotic mount. These observations show that a relatively accessible level of astronomical equipment, of the class often used by amateur astronomers, can be used to record KBO occultations. The data were taken at MIT's George R. Wallace, Jr., Astrophysical Observatory in Westford, MA. A light curve was generated from the data using aperture photometry on the individual images and is presented here. This light curve is being analyzed by Person et al. (this meeting) to provide constraints on Quaoar's size. We also discuss various observing strategies that could be used in the future to optimize the data from this type of event. This work was supported in part by grant NNX10AB27G to MIT from NASA's Planetary Astronomy Division. Student participation was supported in part by NSF's REU program, MIT's Undergraduate Research Opportunities Program, NASA's Massachusetts Space Grant, and the George R. Wallace, Jr., Astrophysical Observatory.

Developing sub 5-m LiDAR DEMs for forested sections of the Alpine and Hope faults, South Island, New Zealand: Implications for structural interpretations

NASA Astrophysics Data System (ADS)

Langridge, R. M.; Ries, W. F.; Farrier, T.; Barth, N. C.; Khajavi, N.; De Pascale, G. P.

2014-07-01

Kilometre-wide airborne light detection and ranging (LiDAR) surveys were collected along portions of the Alpine and Hope faults in New Zealand to assess the potential for generating sub 5-m bare earth digital elevation models (DEMs) from ground return data in areas of dense rainforest (bush) cover as an aid to mapping these faults. The 34-km long Franz-Whataroa LiDAR survey was flown along the densely-vegetated central-most portion of the transpressive Alpine Fault. Six closely spaced flight lines (200 m apart) yielded survey coverage with double overlap of swath collection, which was considered necessary due to the low density of ground returns (0.16 m-2 or a point every 6 m2) under mature West Coast podocarp-broadleaf rainforest. This average point spacing (˜2.5 m) allowed for the generation of a robust, high quality 3-m bare earth DEM. The DEM confirmed the zigzagged form of the surface trace of the Alpine Fault in this area, originally recognised by Norris and Cooper (1995, 1997) and highlights that the surface strike variations are more variant than previously mapped. The 29-km long Hurunui-Hope LiDAR survey was flown east of the Main Divide of the Southern Alps along the dextral-slip Hope Fault, where the terrain is characterised by lower rainfall and more open beech forest. Flight line spacings of ˜275 m were used to generate a DEM from the ground return data. The average ground return values under beech forest were 0.27 m-2 and yielded an estimated cell size suitable for a 2-m DEM. In both cases the LiDAR revealed unprecedented views of the surface geomorphology of these active faults. Lessons learned from our survey methodologies can be employed to plan cost-effective, high-gain airborne surveys to yield bare earth DEMs underneath vegetated terrain and multi-storeyed canopies from densely forested environments across New Zealand and worldwide.

Der deutsche Röntgensatellit ABRIXAS: Mission und wissenschaftliche Zielsetzung.

NASA Astrophysics Data System (ADS)

Predehl, P.

ABRIXAS (A BRoad band Imaging X-ray All-sky Survey) ist ein Röntgensatellit mit sieben 27-fach genesteten Wolterteleskopen, die sich in ihren Brennpunkten eine pn-CCD Kamera teilen. ABRIXAS soll im Frühjahr 1999 auf einer russischen Cosmos-Rakete gestartet werden und die erste abbildende Himmelsdurchmusterung oberhalb von 2.4 keV durchführen. Man erwartet während der dreijährigen Mission wenigstens 10.000 neue Röntgenquellen zu entdecken. Dies sind vor allem solche Quellen, die durch vorgelagerte Staub- und Gasschichten für den ABRIXAS-Vorgänger ROSAT unsichtbar blieben. Darüber hinaus wird ABRIXAS hervorragend geeignet sein, ausgedehnte, diffuse Quellen spektroskopisch zu studieren und Intensitätsvariationen von Röntgenquellen auf sehr unterschiedlichen Zeitskalen zu untersuchen. Das Projekt ist eine wissenschaftliche Zusammenarbeit zwischen dem Astrophysikalischen Institut Potsdam (AIP), dem Institut für Astronomie und Astrophysik der Universität Tübingen (IAAT) und dem Max-Planck-Institut für extraterrestrische Physik (MPE).

DEM simulation of the granular Maxwell's Demon under zero gravity

NASA Astrophysics Data System (ADS)

Wang, Wenguang; Zhou, Zhigang; Zong, Jin; Hou, Meiying

2017-06-01

In this work, granular segregation in a two-compartment cell (Maxwell's Demon) under zero gravity is studied numerically by DEM simulation for comparison with the experimental observation in satellite SJ-10. The effect of three parameters: the total number of particlesN, the excitation strengthΓ, and the position of the window coupling the two compartments, on the segregationɛ and the waiting timeτ are investigated. In the simulation, non-zero segregation under zero gravity is obtained, and the segregation ɛ is found independent of the excitation strengthΓ. The waiting time τ, however, depends strongly onΓ. For higher acceleration Γ, |ɛi| reaches steady state valueɛ faster.

Gully incision rates on the bedrock of a large dip-slope landslide revealed by multi-period LiDAR DEMs

NASA Astrophysics Data System (ADS)

Chan, Y. C.; Hsieh, Y. C.

2017-12-01

Recent advances in airborne laser scanning (ALS) technology have provided a great opportunity for characterizing surface erosion through developing improved methods in multi-period DEM differencing and geomorphometry. This study uses three periods of ALS digital elevation model (DEM) data to analyze the short-term erosional features of the Tsaoling landslide triggered by the 1999 Chi-Chi earthquake in Taiwan. Two methods for calculating the bedrock incision rate, the equal-interval cross section selection method and the continuous swath profiles selection method, were used in the study after nearly ten years of gully incision following the earthquake-triggered dip-slope landslide. Multi-temporal gully incision rates were obtained using the continuous swath profiles selection method, which is considered a practical and convenient approach in terrain change studies. After error estimation and comparison of the multi-period ALS DEMs, the terrain change in different periods can be directly calculated, reducing time-consuming fieldwork such as installation of erosion pins and measurement of topographic cross sections on site. In this study, the gully bedrock incision rates ranged between 0.23 and 3.98 m/year, remarkably higher than the typical results from the previous studies. By comparing the DEM data, aerial photos, and precipitation records of this area, the effects of erosion could be observed from the retreat of the Chunqiu Cliff outline during August 2011 to September 2012. It was inferred that the change in the topographic elevation during 2011-2012 was mainly due to the torrential rain brought by Typhoon Soula, which occurred on 30 July 2012. The local gully incision rate in the lower part of the landslide surface was remarkably faster than that of the other regions, suggesting that the fast incision of the toe area possibly contributes to the occurrence of repeated landslides in the Tsaoling area.

Ein Kredit für Weihnachtsbaumkugeln

NASA Astrophysics Data System (ADS)

Tutsch, Sina

Eine Mathematikerin aus dem DFG-Forschungszentrum Matheon arbeitet an Methoden zur dreidimensionalen Visualisierung. Sie hat die Geschäftsidee, Weihnachtsbaumkugeln mit bewegten Hologrammen herzustellen, die sich individuell gestalten lassen, und plant eine Existenzgründung. Aus einem öffentlichen Förderprogramm erhält sie ein günstiges Darlehen in Höhe von 50 000 Euro. Für die Startphase ihres Unternehmens benötigt sie jedoch den vierfachen Betrag.

DEM study of fabric features governing undrained post-liquefaction shear deformation of sand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Rui; Fu, Pengcheng; Zhang, Jian-Min

In an effort to study undrained post-liquefaction shear deformation of sand, the discrete element method (DEM) is adopted to conduct undrained cyclic biaxial compression simulations on granular assemblies consisting of 2D circular particles. The simulations are able to successfully reproduce the generation and eventual saturation of shear strain through the series of liquefaction states that the material experiences during cyclic loading after the initial liquefaction. Also, DEM simulations with different deviatoric stress amplitudes and initial mean effective stresses on samples with different void ratios and loading histories are carried out to investigate the relationship between various mechanics- or fabric-related variablesmore » and post-liquefaction shear strain development. It is found that well-known metrics such as deviatoric stress amplitude, initial mean effective stress, void ratio, contact normal fabric anisotropy intensity, and coordination number, are not adequately correlated to the observed shear strain development and, therefore, could not possibly be used for its prediction. A new fabric entity, namely the Mean Neighboring Particle Distance (MNPD), is introduced to reflect the space arrangement of particles. It is found that the MNPD has an extremely strong and definitive relationship with the post-liquefaction shear strain development, showing MNPD’s potential role as a parameter governing post-liquefaction behavior of sand.« less

DEM study of fabric features governing undrained post-liquefaction shear deformation of sand

DOE PAGES

Wang, Rui; Fu, Pengcheng; Zhang, Jian-Min; ...

2016-10-05

In an effort to study undrained post-liquefaction shear deformation of sand, the discrete element method (DEM) is adopted to conduct undrained cyclic biaxial compression simulations on granular assemblies consisting of 2D circular particles. The simulations are able to successfully reproduce the generation and eventual saturation of shear strain through the series of liquefaction states that the material experiences during cyclic loading after the initial liquefaction. Also, DEM simulations with different deviatoric stress amplitudes and initial mean effective stresses on samples with different void ratios and loading histories are carried out to investigate the relationship between various mechanics- or fabric-related variablesmore » and post-liquefaction shear strain development. It is found that well-known metrics such as deviatoric stress amplitude, initial mean effective stress, void ratio, contact normal fabric anisotropy intensity, and coordination number, are not adequately correlated to the observed shear strain development and, therefore, could not possibly be used for its prediction. A new fabric entity, namely the Mean Neighboring Particle Distance (MNPD), is introduced to reflect the space arrangement of particles. It is found that the MNPD has an extremely strong and definitive relationship with the post-liquefaction shear strain development, showing MNPD’s potential role as a parameter governing post-liquefaction behavior of sand.« less

Landslide Detection in the Carlyon Beach, WA Peninsula: Analysis Of High Resolution DEMs

NASA Astrophysics Data System (ADS)

Fayne, J.; Tran, C.; Mora, O. E.

2017-12-01

Landslides are geological events caused by slope instability and degradation, leading to the sliding of large masses of rock and soil down a mountain or hillside. These events are influenced by topography, geology, weather and human activity, and can cause extensive damage to the environment and infrastructure, such as the destruction of transportation networks, homes, and businesses. It is therefore imperative to detect early-warning signs of landslide hazards as a means of mitigation and disaster prevention. Traditional landslide surveillance consists of field mapping, but the process is expensive and time consuming. This study uses Light Detection and Ranging (LiDAR) derived Digital Elevation Models (DEMs) and k-means clustering and Gaussian Mixture Model (GMM) to analyze surface roughness and extract spatial features and patterns of landslides and landslide-prone areas. The methodology based on several feature extractors employs an unsupervised classifier on the Carlyon Beach Peninsula in the state of Washington to attempt to identify slide potential terrain. When compared with the independently compiled landslide inventory map, the proposed algorithm correctly classifies up to 87% of the terrain. These results suggest that the proposed methods and LiDAR-derived DEMs can provide important surface information and be used as efficient tools for digital terrain analysis to create accurate landslide maps.

Automated classifications of topography from DEMs by an unsupervised nested-means algorithm and a three-part geometric signature

USGS Publications Warehouse

Iwahashi, J.; Pike, R.J.

2007-01-01

An iterative procedure that implements the classification of continuous topography as a problem in digital image-processing automatically divides an area into categories of surface form; three taxonomic criteria-slope gradient, local convexity, and surface texture-are calculated from a square-grid digital elevation model (DEM). The sequence of programmed operations combines twofold-partitioned maps of the three variables converted to greyscale images, using the mean of each variable as the dividing threshold. To subdivide increasingly subtle topography, grid cells sloping at less than mean gradient of the input DEM are classified by designating mean values of successively lower-sloping subsets of the study area (nested means) as taxonomic thresholds, thereby increasing the number of output categories from the minimum 8 to 12 or 16. Program output is exemplified by 16 topographic types for the world at 1-km spatial resolution (SRTM30 data), the Japanese Islands at 270??m, and part of Hokkaido at 55??m. Because the procedure is unsupervised and reflects frequency distributions of the input variables rather than pre-set criteria, the resulting classes are undefined and must be calibrated empirically by subsequent analysis. Maps of the example classifications reflect physiographic regions, geological structure, and landform as well as slope materials and processes; fine-textured terrain categories tend to correlate with erosional topography or older surfaces, coarse-textured classes with areas of little dissection. In Japan the resulting classes approximate landform types mapped from airphoto analysis, while in the Americas they create map patterns resembling Hammond's terrain types or surface-form classes; SRTM30 output for the United States compares favorably with Fenneman's physical divisions. Experiments are suggested for further developing the method; the Arc/Info AML and the map of terrain classes for the world are available as online downloads. ?? 2006 Elsevier

1963 Vajont rock slide: a comparison between 3D DEM and 3D FEM

NASA Astrophysics Data System (ADS)

Crosta, Giovanni; Utili, Stefano; Castellanza, Riccardo; Agliardi, Federico; Bistacchi, Andrea; Weng Boon, Chia

2013-04-01

Data on the exact location of the failure surface of the landslide have been used as the starting point for the modelling of the landslide. 3 dimensional numerical analyses were run employing both the discrete element method (DEM) and a Finite Element Method (FEM) code. In this work the focus is on the prediction of the movement of the landlside during its initial phase of detachment from Mount Toc. The results obtained by the two methods are compared and conjectures on the observed discrepancies of the predictions between the two methods are formulated. In the DEM simulations the internal interaction of the sliding blocks and the expansion of the debris is obtained as a result of the kinematic interaction among the rock blocks resulting from the jointing of the rock mass involved in the slide. In the FEM analyses, the c-phi reduction technique was employed along the predefine failure surface until the onset of the landslide occurred. In particular, two major blocks of the landslide were identified and the stress, strain and displacement fields at the interface between the two blocks were analysed in detail.

The 10 m-resolution TINITALY DEM as a trans-disciplinary basis for the analysis of the Italian territory: Current trends and new perspectives

NASA Astrophysics Data System (ADS)

Tarquini, Simone; Nannipieri, Luca

2017-03-01

The increasing availability of high resolution digital elevation models (DEMs) is changing our viewpoint towards Earth surface landforms. Nevertheless, large-coverage, intermediate-resolution DEMs are still largely used, and can be the ideal choice in several applications based on the processing of spatially-integrated information. In 2012 the Istituto Nazionale di Geofisica e Vulcanologia opened a website for the free download of the "TINTALY" Digital Elevation Model (DEM), which covers the whole Italian territory. Since then, about 700 users from 28 different countries have been accredited for data download, and a report of 4 years of data dissemination and use is presented. The analysis of the intended use reveals that the 10 m-resolution, seamless TINITALY DEM is of use for an extremely assorted research community. Accredited users are working in virtually any branch of the Earth Sciences (e.g. Volcanology, Seismology, and Geomorphology), in spatially integrated humanities (e.g. History and Archaeology), and in other thematic areas such as in applied Physics and Zoology. Many users are also working in local administrations (e.g. Regions and Municipalities) for civil protection or land use planning purposes. In summary, the documented activity shows that the dissemination of seamless, large coverage elevation datasets can fertilize the technological progress of the whole society providing a significant benefit to stakeholders.

Rethinking the Relationship Between Academia and Industry: Qualitative Case Studies of MIT and Stanford.

PubMed

Zhu, Fengliang; Hawk, Soaring

2016-10-01

As knowledge has become more closely tied to economic development, the interrelationship between academia and industry has become stronger. The result has been the emergence of what Slaughter and Leslie call academic capitalism. Inevitably, tensions between academia and industry arise; however, universities such as MIT and Stanford with long traditions of industry interaction have been able to achieve a balance between academic and market values. This paper describes the strategies adopted by MIT and Stanford to achieve this balance. The results indicate that implicit culture is a stronger determinant of balance than are explicit rules. Finally, the author proposes a concept of balance to reconsider the relationship between academia and industry: today's universities, particularly those with strengths in engineering and management, are both symbiotic and interdependent with industry. A reasonable attitude toward the university-industry relationship is that of balance rather than strict separation. Universities can thus establish effective mechanisms to reach a balance between conflicting values.

DEM simulation of dendritic grain random packing: application to metal alloy solidification

NASA Astrophysics Data System (ADS)

Olmedilla, Antonio; Založnik, Miha; Combeau, Hervé

2017-06-01

The random packing of equiaxed dendritic grains in metal-alloy solidification is numerically simulated and validated via an experimental model. This phenomenon is characterized by a driving force which is induced by the solid-liquid density difference. Thereby, the solid dendritic grains, nucleated in the melt, sediment and pack with a relatively low inertia-to-dissipation ratio, which is the so-called Stokes number. The characteristics of the particle packed porous structure such as solid packing fraction affect the final solidified product. A multi-sphere clumping Discrete Element Method (DEM) approach is employed to predict the solid packing fraction as function of the grain geometry under the solidification conditions. Five different monodisperse noncohesive frictionless particle collections are numerically packed by means of a vertical acceleration: a) three dendritic morphologies; b) spheres and c) one ellipsoidal geometry. In order to validate our numerical results with solidification conditions, the sedimentation and packing of two monodisperse collections (spherical and dendritic) is experimentally carried out in a viscous quiescent medium. The hydrodynamic similarity is respected between the actual phenomenon and the experimental model, that is a low Stokes number, o(10-3). In this way, the experimental average solid packing fraction is employed to validate the numerical model. Eventually, the average packing fraction is found to highly depend on the equiaxed dendritic grain sphericity, with looser packings for lower sphericity.

Quantitative Analyse und Visualisierung der Herzfunktionen

NASA Astrophysics Data System (ADS)

Sauer, Anne; Schwarz, Tobias; Engel, Nicole; Seitel, Mathias; Kenngott, Hannes; Mohrhardt, Carsten; Loßnitzer, Dirk; Giannitsis, Evangelos; Katus, Hugo A.; Meinzer, Hans-Peter

Die computergestützte bildbasierte Analyse der Herzfunktionen ist mittlerweile Standard in der Kardiologie. Die verfügbaren Produkte erfordern meist ein hohes Maß an Benutzerinteraktion und somit einen erhöhten Zeitaufwand. In dieser Arbeit wird ein Ansatz vorgestellt, der dem Kardiologen eine größtenteils automatische Analyse der Herzfunktionen mittels MRT-Bilddaten ermöglicht und damit Zeitersparnis schafft. Hierbei werden alle relevanten herzphysiologsichen Parameter berechnet und mithilfe von Diagrammen und Graphen visualisiert. Diese Berechnungen werden evaluiert, indem die ermittelten Werte mit manuell vermessenen verglichen werden. Der hierbei berechnete mittlere Fehler liegt mit 2,85 mm für die Wanddicke und 1,61 mm für die Wanddickenzunahme immer noch im Bereich einer Pixelgrösse der verwendeten Bilder.

Time-averaged discharge rate of subaerial lava at Kīlauea Volcano, Hawai‘i, measured from TanDEM-X interferometry: Implications for magma supply and storage during 2011-2013

USGS Publications Warehouse

Poland, Michael P.

2014-01-01

Differencing digital elevation models (DEMs) derived from TerraSAR add-on for Digital Elevation Measurements (TanDEM-X) synthetic aperture radar imagery provides a measurement of elevation change over time. On the East Rift Zone (EZR) of Kīlauea Volcano, Hawai‘i, the effusion of lava causes changes in topography. When these elevation changes are summed over the area of an active lava flow, it is possible to quantify the volume of lava emplaced at the surface during the time spanned by the TanDEM-X data—a parameter that can be difficult to measure across the entirety of an ~100 km2 lava flow field using ground-based techniques or optical remote sensing data. Based on the differences between multiple TanDEM-X-derived DEMs collected days to weeks apart, the mean dense-rock equivalent time-averaged discharge rate of lava at Kīlauea between mid-2011 and mid-2013 was approximately 2 m3/s, which is about half the long-term average rate over the course of Kīlauea's 1983–present ERZ eruption. This result implies that there was an increase in the proportion of lava stored versus erupted, a decrease in the rate of magma supply to the volcano, or some combination of both during this time period. In addition to constraining the time-averaged discharge rate of lava and the rates of magma supply and storage, topographic change maps derived from space-based TanDEM-X data provide insights into the four-dimensional evolution of Kīlauea's ERZ lava flow field. TanDEM-X data are a valuable complement to other space-, air-, and ground-based observations of eruptive activity at Kīlauea and offer great promise at locations around the world for aiding with monitoring not just volcanic eruptions but any hazardous activity that results in surface change, including landslides, floods, earthquakes, and other natural and anthropogenic processes.

Can DEM time series produced by UAV be used to quantify diffuse erosion in an agricultural watershed?

NASA Astrophysics Data System (ADS)

Pineux, N.; Lisein, J.; Swerts, G.; Bielders, C. L.; Lejeune, P.; Colinet, G.; Degré, A.

2017-03-01

Erosion and deposition modelling should rely on field data. Currently these data are seldom available at large spatial scales and/or at high spatial resolution. In addition, conventional erosion monitoring approaches are labour intensive and costly. This calls for the development of new approaches for field erosion data acquisition. As a result of rapid technological developments and low cost, unmanned aerial vehicles (UAV) have recently become an attractive means of generating high resolution digital elevation models (DEMs). The use of UAV to observe and quantify gully erosion is now widely established. However, in some agro-pedological contexts, soil erosion results from multiple processes, including sheet and rill erosion, tillage erosion and erosion due to harvest of root crops. These diffuse erosion processes often represent a particular challenge because of the limited elevation changes they induce. In this study, we propose to assess the reliability and development perspectives of UAV to locate and quantify erosion and deposition in a context of an agricultural watershed with silt loam soils and a smooth relief. Erosion and deposition rates derived from high resolution DEM time series are compared to field measurements. The UAV technique demonstrates a high level of flexibility and can be used, for instance, after a major erosive event. It delivers a very high resolution DEM (pixel size: 6 cm) which allows us to compute high resolution runoff pathways. This could enable us to precisely locate runoff management practices such as fascines. Furthermore, the DEMs can be used diachronically to extract elevation differences before and after a strongly erosive rainfall and be validated by field measurements. While the analysis for this study was carried out over 2 years, we observed a tendency along the slope from erosion to deposition. Erosion and deposition patterns detected at the watershed scale are also promising. Nevertheless, further development in the

Quantitative profiling of drug-associated proteomic alterations by combined 2-nitrobenzenesulfenyl chloride (NBS) isotope labeling and 2DE/MS identification.

PubMed

Ou, Keli; Kesuma, Djohan; Ganesan, Kumaresan; Yu, Kun; Soon, Sou Yen; Lee, Suet Ying; Goh, Xin Pei; Hooi, Michelle; Chen, Wei; Jikuya, Hiroyuki; Ichikawa, Tetsuo; Kuyama, Hiroki; Matsuo, Ei-ichi; Nishimura, Osamu; Tan, Patrick

2006-09-01

The identification of drug-responsive biomarkers in complex protein mixtures is an important goal of quantitative proteomics. Here, we describe a novel approach for identifying such drug-induced protein alterations, which combines 2-nitrobenzenesulfenyl chloride (NBS) tryptophan labeling with two-dimensional gel electrophoresis (2DE)/mass spectrometry (MS). Lysates from drug-treated and control samples are labeled with light or heavy NBS moiety and separated on a common 2DE gel, and protein alterations are identified by MS through the differential intensity of paired NBS peptide peaks. Using NBS/2DE/MS, we profiled the proteomic alterations induced by tamoxifen (TAM) in the estrogen receptor (ER) positive MCF-7 breast cancer cell line. Of 88 protein spots that significantly changed upon TAM treatment, 44 spots representing 23 distinct protein species were successfully identified with NBS-paired peptides. Of these 23 TAM-altered proteins, 16 (70%) have not been previously associated with TAM or ER activity. We found the NBS labeling procedure to be both technically and biologically reproducible, and the NBS/2DE/MS alterations exhibited good concordance with conventional 2DE differential protein quantitation, with discrepancies largely due to the comigration of distinct proteins in the regular 2DE gels. To validate the NBS/2DE/MS results, we used immunoblotting to confirm GRP78, CK19, and PA2G4 as bona fide TAM-regulated proteins. Furthermore, we demonstrate that PA2G4 expression can serve as a novel prognostic factor for disease-free survival in two independent breast cancer patient cohorts. To our knowledge, this is the first report describing the proteomic changes in breast cancer cells induced by TAM, the most commonly used selective estrogen receptor modulator (SERM). Our results indicate that NBS/2DE/MS may represent a more reliable approach for cellular protein quantitation than conventional 2DE approaches.

Virtuelle Kraftwerke für Smart Markets

NASA Astrophysics Data System (ADS)

Dürr, Thomas; Heyne, Jean-Christoph

In den zurückliegenden Jahren haben insbesondere zwei Trends die Stromversorgung bestimmt: der starke Anstieg der dezentralen und der Ausbau der regenerativen Stromerzeugung, die vor allem in den Verteilnetzen stattfinden. Angesichts dieser Entwicklung gewinnen virtuelle Kraftwerke (VK) immer mehr an Bedeutung. In der frühen Phase waren VK insbesondere eine Möglichkeit, kleine dezentrale Erzeuger zu einer größeren Einheit zu bündeln und sie so marktfähig zu machen. Heute werden sie - überwacht und gesteuert über ein Dezentrales Energie-Management-System (DEMS) - gemeinsam mit Demand Response betrieben, also dem Reagieren eines Energieabnehmers auf Marktpreise. Das Demand Side Management soll zur Flexibilisierung der Industrie beitragen. Da der Ausbau der Übertragungsnetze nur schleppend vorankommt, kann die Nutzung von lastseitiger Flexibilität einen wichtigen Beitrag zur Versorgungssicherheit leisten. Im zweiten Teil des Beitrags geht es um die Entwicklung der Märkte. Großes Interesse besteht immer noch an der Regelenergie, zumal der Bedarf bis 2050 deutlich steigen wird. Die Spotmärkte Intraday und Day-Ahead wachsen kontinuierlich, deshalb werden sie für VK immer wichtiger. Am Ende gibt der Beitrag einen Ausblick auf die künftige Entwicklung, in der Regelenergie- und Spotmärkte noch eine Rolle spielen, aber andere Geschäftsmodelle wichtiger werden. Darüber hinaus geht es um langfristige Entwicklungen, die z. B. zusätzliche Serviceleistungen durch VK betreffen.

Recent glacier mass balance and area changes in the Kangri Karpo Mountains from DEMs and glacier inventories

NASA Astrophysics Data System (ADS)

Wu, Kunpeng; Liu, Shiyin; Jiang, Zongli; Xu, Junli; Wei, Junfeng; Guo, Wanqin

2018-01-01

Due to the influence of the Indian monsoon, the Kangri Karpo Mountains in the south-east of the Tibetan Plateau is in the most humid and one of the most important and concentrated regions containing maritime (temperate) glaciers. Glacier mass loss in the Kangri Karpo is an important contributor to global mean sea level rise, and changes run-off distribution, increasing the risk of glacial-lake outburst floods (GLOFs). Because of its inaccessibility and high labour costs, information about the Kangri Karpo glaciers is still limited. Using geodetic methods based on digital elevation models (DEMs) derived from 1980 topographic maps from the Shuttle Radar Topography Mission (SRTM) (2000) and from TerraSAR-X/TanDEM-X (2014), this study has determined glacier elevation changes. Glacier area and length changes between 1980 and 2015 were derived from topographical maps and Landsat TM/ETM+/OLI images. Results show that the Kangri Karpo contained 1166 glaciers with an area of 2048.50 ± 48.65 km2 in 2015. Ice cover diminished by 679.51 ± 59.49 km2 (24.9 ± 2.2 %) or 0.71 ± 0.06 % a-1 from 1980 to 2015, although nine glaciers advanced. A glacierized area of 788.28 km2, derived from DEM differencing, experienced a mean mass loss of 0.46 ± 0.08 m w.e. a-1 from 1980 to 2014. Shrinkage and mass loss accelerated significantly from 2000 to 2015 compared to 1980-2000, consistent with a warming climate.

Identifying slow-moving landslides using LiDAR DEM and SAR interferometry: An Example of 2006 Meinong Earthquake

NASA Astrophysics Data System (ADS)

Chen, R. F.; Lin, C. W.; Hsu, Y. J.; Zhang, L.; Liang, H. Y.

2017-12-01

The February 6 Meinong Earthquake of 2016 (ML=6.4; at 23.85ºN, 120.81ºE), with a focal depth of 16.7 km, was triggered by an unknown blind thrust in southern Taiwan. The earthquake not only induced coseismic crustal deformation, but also triggered slow-moving landslides nearby the Longchuan active fault. In this study, high-resolution LiDAR derived DEM of 2010 is used to recognize locations of previous slow-moving landslides according to their topographic signatures, such as main escarpment, trench, double ridge, and crown cracks. Within an area of 4.5 km x 1.8 km along Longchuan fault near the ridge of Longchuan mountain, over 50 sites with landslide signatures are recognized, and three of them are over 10 ha. These earthquake-induced landslide deformations are detected from InSAR (synthetic aperture radar interferometry) images using Advanced Land Observing Satellite ALOS2/Phased-array L band and Sentinel 1 C-band SAR (PALSAR) data taken before and after the earthquake; some significant landslide deformation are even overlapped with areas where previous slow moving landslides were identified on the LiDAR DEM. Additionally, field investigation right after the earthquake in the study area also support that these previously identified landslides reactivated in the earthquake. Although these landslides do not cause serious damage due to their minor displacement in the Meinong Earthquake, the study results prove that LiDAR DEM is a powerful tool to identify and continuously monitor slow-motion landslides for preventing catastrophic failures that may be caused by hazardous earthquake or heavy rainfall.

Shape-from-shading using Landsat 8 and airborne laser altimetry over ice sheets: toward new regional DEMs of Greenland and Antarctica

NASA Astrophysics Data System (ADS)

Moussavi, M. S.; Scambos, T.; Haran, T. M.; Klinger, M. J.; Abdalati, W.

2015-12-01

We investigate the capability of Landsat 8's Operational Land Imager (OLI) instrument to quantify subtle ice sheet topography of Greenland and Antarctica. We use photoclinometry, or 'shape-from-shading', a method of deriving surface topography from local variations in image brightness due to varying surface slope. Photoclinomeetry is applicable over ice sheet areas with highly uniform albedo such as regions covered by recent snowfall. OLI imagery is available from both ascending and descending passes near the summer solstice period for both ice sheets. This provides two views of the surface features from two distinct solar azimuth illumination directions. Airborne laser altimetry data from the Airborne Topographic Mapper (ATM) instrument (flying on the Operation Ice Bridge program) are used to quantitatively convert the image brightness variations of surface undulations to surface slope. To validate the new DEM products, we use additional laser altimetry profiles collected over independent sites from Ice Bridge and ICESat, and high-resolution WorldView-2 DEMs. The photoclinometry-derived DEM products will be useful for studying surface elevation changes, enhancing bedrock elevation maps through inversion of surface topography, and inferring local variations in snow accumulation rates.

Validation Of DEM Data Dvied From World View 3 Stero Imagery For Low Elevation Majuro Atoll, Marchall Islands

EPA Science Inventory

The availability of surface elevation data for the Marshall Islands has been identified as a "massive" data gap for conducting vulnerability assessments and the subsequent development of climate change adaption strategies. Specifically, digital elevation model (DEM) data are nee...

MitBASE : a comprehensive and integrated mitochondrial DNA database. The present status

PubMed Central

Attimonelli, M.; Altamura, N.; Benne, R.; Brennicke, A.; Cooper, J. M.; D’Elia, D.; Montalvo, A. de; Pinto, B. de; De Robertis, M.; Golik, P.; Knoop, V.; Lanave, C.; Lazowska, J.; Licciulli, F.; Malladi, B. S.; Memeo, F.; Monnerot, M.; Pasimeni, R.; Pilbout, S.; Schapira, A. H. V.; Sloof, P.; Saccone, C.

2000-01-01

MitBASE is an integrated and comprehensive database of mitochondrial DNA data which collects, under a single interface, databases for Plant, Vertebrate, Invertebrate, Human, Protist and Fungal mtDNA and a Pilot database on nuclear genes involved in mitochondrial biogenesis in Saccharomyces cerevisiae. MitBASE reports all available information from different organisms and from intraspecies variants and mutants. Data have been drawn from the primary databases and from the literature; value adding information has been structured, e.g., editing information on protist mtDNA genomes, pathological information for human mtDNA variants, etc. The different databases, some of which are structured using commercial packages (Microsoft Access, File Maker Pro) while others use a flat-file format, have been integrated under ORACLE. Ad hoc retrieval systems have been devised for some of the above listed databases keeping into account their peculiarities. The database is resident at the EBI and is available at the following site: http://www3.ebi.ac.uk/Research/Mitbase/mitbase.pl . The impact of this project is intended for both basic and applied research. The study of mitochondrial genetic diseases and mitochondrial DNA intraspecies diversity are key topics in several biotechnological fields. The database has been funded within the EU Biotechnology programme. PMID:10592207

MIT-Skywalker: considerations on the Design of a Body Weight Support System.

PubMed

Gonçalves, Rogério Sales; Krebs, Hermano Igo

2017-09-06

To provide body weight support during walking and balance training, one can employ two distinct embodiments: support through a harness hanging from an overhead system or support through a saddle/seat type. This paper presents a comparison of these two approaches. Ultimately, this comparison determined our selection of the body weight support system employed in the MIT-Skywalker, a robotic device developed for the rehabilitation/habilitation of gait and balance after a neurological injury. Here we will summarize our results with eight healthy subjects walking on the treadmill without any support, with 30% unloading supported by a harness hanging from an overhead system, and with a saddle/seat-like support system. We compared the center of mass as well as vertical and mediolateral trunk displacements across different walking speeds and support. The bicycle/saddle system had the highest values for the mediolateral inclination, while the overhead harness body weight support showed the lowest values at all speeds. The differences were statistically significant. We selected the bicycle/saddle system for the MIT-Skywalker. It allows faster don-and-doff, better centers the patient to the split treadmill, and allows all forms of training. The overhead harness body weight support might be adequate for rhythmic walking training but limits any potential for balance training.

Measuring the quality of life of people with dementia in nursing homes in Germany - the study protocol for the Qol-Dem Project.

PubMed

Dichter, Martin Nikolaus; Halek, Margareta; Dortmann, Olga; Meyer, Gabriele; Bartholomeyczik, Sabine

2013-01-01

QUALIDEM is a standardized dementia-specific quality of life (Qol) measurement, which was developed and validated in the Netherlands. A German version has been available since 2008. This study protocol describes the design and methodology for the quality of life of people with dementia (Qol-Dem) project. This project aims to evaluate the reliability and validity of the German version of the QUALIDEM. Due to the lack of both a universal definition of Qol and of standards to verify the validity of Qol measurements, this study is divided into three phases. The aim of the first theoretical phase is the development of a dementia-specific Qol model as a result of a meta-synthesis of qualitative studies. The second empirical phase consists of the three following steps: (a) an investigation of the scalability and internal consistency of the measure, (b) an evaluation of the interrater and intrarater reliability, and (c) an extensive evaluation of the validity of the QUALIDEM. The resulting Qol model (phase 1) will be used for the selection of appropriate comparators for validity testing. In the third phase, the QUALIDEM will be adapted, if necessary, based on the knowledge generated in the first two phases. The findings of the Qol-Dem project should deliver an accurate assessment of the psychometric properties of the German version of the QUALIDEM. The results will contribute to the further development of the instrument. Furthermore, the results will contribute to the theoretical development of the concept of Qol among people with dementia.

Validation of DEM Data Derived from World View 3 Stereo Imagery for Low Elevation Majuro Atoll, Marshall Islands

EPA Science Inventory

The availability of surface elevation data for the Marshall Islands has been identified as a “massive” data gap for conducting vulnerability assessments and the subsequent development of climate change adaption strategies. Specifically, digital elevation model (DEM) data are need...

Teleoperation experiments with a Utah/MIT hand and a VPL DataGlove

NASA Technical Reports Server (NTRS)

Clark, D.; Demmel, J.; Hong, J.; Lafferriere, Gerardo; Salkind, L.; Tan, X.

1989-01-01

A teleoperation system capable of controlling a Utah/MIT Dextrous Hand using a VPL DataGlove as a master is presented. Additionally the system is capable of running the dextrous hand in robotic (autonomous) mode as new programs are developed. The software and hardware architecture used is presented and the experiments performed are described. The communication and calibration issues involved are analyzed and applications to the analysis and development of automated dextrous manipulations are investigated.

An Investigation of Transgressive Deposits in Late Pleistocene Lake Bonneville using GPR and UAV-produced DEMs.

NASA Astrophysics Data System (ADS)

Schide, K.; Jewell, P. W.; Oviatt, C. G.; Jol, H. M.

2015-12-01

Lake Bonneville was the largest of the Pleistocene pluvial lakes that once filled the Great Basin of the interior western United States. Its two most prominent shorelines, Bonneville and Provo, are well documented but many of the lake's intermediate shoreline features have yet to be studied. These transgressive barriers and embankments mark short-term changes in the regional water budget and thus represent a proxy for local climate change. The internal and external structures of these features are analyzed using the following methods: ground penetrating radar, 5 meter auto-correlated DEMs, 1-meter DEMs generated from LiDAR, high-accuracy handheld GPS, and 3D imagery collected with an unmanned aerial vehicle. These methods in mapping, surveying, and imaging provide a quantitative analysis of regional sediment availability, transportation, and deposition as well as changes in wave and wind energy. These controls help define climate thresholds and rates of landscape evolution in the Great Basin during the Pleistocene that are then evaluated in the context of global climate change.

Improvement of dem Generation from Aster Images Using Satellite Jitter Estimation and Open Source Implementation

NASA Astrophysics Data System (ADS)

Girod, L.; Nuth, C.; Kääb, A.

2015-12-01

The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) system embarked on the Terra (EOS AM-1) satellite has been a source of stereoscopic images covering the whole globe at a 15m resolution at a consistent quality for over 15 years. The potential of this data in terms of geomorphological analysis and change detection in three dimensions is unrivaled and needs to be exploited. However, the quality of the DEMs and ortho-images currently delivered by NASA (ASTER DMO products) is often of insufficient quality for a number of applications such as mountain glacier mass balance. For this study, the use of Ground Control Points (GCPs) or of other ground truth was rejected due to the global "big data" type of processing that we hope to perform on the ASTER archive. We have therefore developed a tool to compute Rational Polynomial Coefficient (RPC) models from the ASTER metadata and a method improving the quality of the matching by identifying and correcting jitter induced cross-track parallax errors. Our method outputs more accurate DEMs with less unmatched areas and reduced overall noise. The algorithms were implemented in the open source photogrammetric library and software suite MicMac.

Application of the PROMETHEE technique to determine depression outlet location and flow direction in DEM

NASA Astrophysics Data System (ADS)

Chou, Tien-Yin; Lin, Wen-Tzu; Lin, Chao-Yuan; Chou, Wen-Chieh; Huang, Pi-Hui

2004-02-01

With the fast growing progress of computer technologies, spatial information on watersheds such as flow direction, watershed boundaries and the drainage network can be automatically calculated or extracted from a digital elevation model (DEM). The stubborn problem that depressions exist in DEMs has been frequently encountered while extracting the spatial information of terrain. Several filling-up methods have been proposed for solving depressions. However, their suitability for large-scale flat areas is inadequate. This study proposes a depression watershed method coupled with the Preference Ranking Organization METHod for Enrichment Evaluations (PROMETHEEs) theory to determine the optimal outlet and calculate the flow direction in depressions. Three processing procedures are used to derive the depressionless flow direction: (1) calculating the incipient flow direction; (2) establishing the depression watershed by tracing the upstream drainage area and determining the depression outlet using PROMETHEE theory; (3) calculating the depressionless flow direction. The developed method was used to delineate the Shihmen Reservoir watershed located in Northern Taiwan. The results show that the depression watershed method can effectively solve the shortcomings such as depression outlet differentiating and looped flow direction between depressions. The suitability of the proposed approach was verified.

Low-altitude remote sensing dataset of DEM and RGB mosaic for AB corridor on July 13 2013 and L2 corridor on July 21 2013

DOE Data Explorer

Baptiste Dafflon

2015-04-07

Low-altitude remote sensing dataset including DEM and RGB mosaic for AB (July 13 2013) and L2 corridor (July 21 2013).Processing flowchart for each corridor:Ground control points (GCP, 20.3 cm square white targets, every 20 m) surveyed with RTK GPS. Acquisition of RGB pictures using a Kite-based platform. Structure from Motion based reconstruction using hundreds of pictures and GCP coordinates. Export of DEM and RGB mosaic in geotiff format (NAD 83, 2012 geoid, UTM zone 4 north) with pixel resolution of about 2 cm, and x,y,z accuracy in centimeter range (less than 10 cm). High-accuracy and high-resolution inside GCPs zone for L2 corridor (500x20m), AB corridor (500x40) DEM will be updated once all GCPs will be measured. Only zones between GCPs are accurate although all the mosaic is provided.

Discrete element method (DEM) simulations of stratified sampling during solid dosage form manufacturing.

PubMed

Hancock, Bruno C; Ketterhagen, William R

2011-10-14

Discrete element model (DEM) simulations of the discharge of powders from hoppers under gravity were analyzed to provide estimates of dosage form content uniformity during the manufacture of solid dosage forms (tablets and capsules). For a system that exhibits moderate segregation the effects of sample size, number, and location within the batch were determined. The various sampling approaches were compared to current best-practices for sampling described in the Product Quality Research Institute (PQRI) Blend Uniformity Working Group (BUWG) guidelines. Sampling uniformly across the discharge process gave the most accurate results with respect to identifying segregation trends. Sigmoidal sampling (as recommended in the PQRI BUWG guidelines) tended to overestimate potential segregation issues, whereas truncated sampling (common in industrial practice) tended to underestimate them. The size of the sample had a major effect on the absolute potency RSD. The number of sampling locations (10 vs. 20) had very little effect on the trends in the data, and the number of samples analyzed at each location (1 vs. 3 vs. 7) had only a small effect for the sampling conditions examined. The results of this work provide greater understanding of the effect of different sampling approaches on the measured content uniformity of real dosage forms, and can help to guide the choice of appropriate sampling protocols. Copyright © 2011 Elsevier B.V. All rights reserved.

Star in Deep Freeze Chills Theory, MIT Researchers Report

NASA Astrophysics Data System (ADS)

2001-09-01

CAMBRIDGE, Mass. -- Like a frozen turkey that just won't thaw, a strange star near the center of the Milky Way is surprising MIT experts and colleagues with its remarkably low temperature. The odd behavior is chilling current theories of stellar physics. A famously battered neutron star named KS 1731-260 appears no hotter than some of its tranquil brethren, despite enduring the heat of constant thermonuclear explosions with the force of billions of hydrogen bombs every second across a region only a few miles wide for the past 12 years. Dr. Rudi Wijnands, an astrophysicist at MIT's Center for Space Research, used the Chandra X-ray Observatory to measure the temperature of the neutron star at a very opportune moment, only months after the nuclear war apparently ended and the smoke cleared. He presented his team's findings September 5 in Washington, D.C. at a scientific conference entitled "Two Years of Science with Chandra." "Twelve years of constant thermonuclear explosions: One would think that would heat things up," said Wijnands. "This leaves us wondering whether some neutron stars are in the freezer for a much longer time than previously thought and consequently take a long time to heat up, or whether they cool down incredibly fast. Either explanation has profound implications for our field." Neutron stars are the dense, core remains of stars once many times more massive than our Sun. They are created in dazzling supernovas, in which the outer shell of the star explodes into space, and the core, containing about as much mass as the Sun, implodes and collapses into a sphere no wider than Cambridge, Massachusetts. Despite their tiny size, neutron stars are visible in several ways. One is through accretion. Neutron stars are a strong source of gravity. When they exist in binary star systems, such as KS 1731-260, they can attract the gas from what is often a "healthy" hydrogen-burning companion star (although the nature of KS 1731-260's companion is not clear.) Gas

Near-real time orbit determination for the GPS, CHAMP, GRACE, TerraSAR-X, and TanDEM-X satellites

NASA Astrophysics Data System (ADS)

Michalak, Grzegorz; Koenig, Rolf

The GFZ German Research Centre for Geosciences developed a near-real time (NRT) orbit gen-eration system for GPS and Low Earth Orbiting (LEO) satellites to support radio occultation data processing for the CHAMP, GRACE, Terra-SAR-X and the upcoming TanDEM-X mis-sions and fast baseline determination for the TanDEM-X mission. Precise NRT orbits are being generated for the CHAMP and GRACE-A satellites since August 2006 and for TerraSAR-X since August 2007. For each LEO, the system consists of three independent chains delivering NRT orbits with different latencies and accuracies. The first chain generates in a preceding step NRT GPS orbits and clock biases and based thereon LEO orbits with delays of 30 minutes counted from the last measurement point to the time the orbit product is available. The orbit accuracies can be assessed via Satellite Laser Ranging (SLR) to 7 cm. The second chain is based on predicted GPS orbits from the International GNSS Service (IGS) but endowed with in-house estimated clock biases. This chain generates orbits with the same latency of 30 minutes but with better accuracies of 5 cm SLR RMS. The third chain, the least accurate but the fastest, is based on predicted IGS GPS orbits and clocks and delivers LEO orbits with latencies of 13 minutes and accuracies of 10 cm SLR RMS. The system design is such that it can easily be extended to cope with new satellites like TanDEM-X requiring precise and fast available orbits.

Zufällige Signale

NASA Astrophysics Data System (ADS)

Plaßmann, Wilfried

Die hier betrachteten Signale werden auch als stochastische Signale bezeichnet. Sie sind zufällig, d. h. ihr Augenblickswert ist nicht vorhersagbar. Abb. 118.1 zeigt eine Unterteilung nach den Signaleigenschaften. Über die nichtstationären Signale lässt sich keinerlei Aussage machen, und sie werden hier deshalb auch nicht weiter betrachtet. Für die stationären Signale gilt, dass ihr Momentanwert zwar auch nicht vorhergesagt werden kann, dass sie aber trotzdem gewisse auswertbare Eigenschaften besitzen, die allerdings statistischer Art sind und deshalb nur mit den Gesetzen der Wahrscheinlichkeitstheorie erfasst werden können. Zwar sind - theoretisch - für die Anwendung der Wahrscheinlichkeitstheorie unendlich viele Probenwerte zu nehmen, in der Praxis hat sich aber gezeigt, dass man auch mit einer endlichen Anzahl dem gesuchten Wert schon ausreichend nahe kommen kann.

Thermal characteristics of a B8.3 flare observed on July 04, 2009

NASA Astrophysics Data System (ADS)

Awasthi, Arun Kumar; Sylwester, Barbara; Sylwester, Janusz; Jain, Rajmal

We explore the temporal evolution of flare plasma parameters including temperature (T) - differential emission measure (DEM) relationship by analyzing high spectral and temporal cadence of X-ray emission in 1.6-8.0 keV energy band, recorded by SphinX (Polish) and Solar X-ray Spectrometer (SOXS; Indian) instruments, during a B8.3 flare which occurred on July 04, 2009. SphinX records X-ray emission in 1.2-15.0 keV energy band with the temporal and spectral cadence as good as 6 μs and 0.4 keV, respectively. On the other hand, SOXS provides X-ray observations in 4-25 keV energy band with the temporal and spectral resolution of 3 s and 0.7 keV, respectively. We derive the thermal plasma parameters during impulsive phase of the flare employing well-established Withbroe-Sylwester DEM inversion algorithm.

Lasers, their development, and applications at M.I.T. Lincoln Laboratory

NASA Technical Reports Server (NTRS)

Rediker, R. H.; Melngailis, I.; Mooradian, A.

1984-01-01

A historical account of the work on lasers at MIT Lincoln Laboratory is presented. Highlighted are the efforts that led to the coinvention of the semiconductor laser and the Laboratory's later role in establishing the feasibility of GaInAsP/InP semiconductor lasers for use in fiber telecommunications at 1.3-1.5 micron wavelengths. Descriptions of other important developments include tunable lead-salt semiconductor and solid-state lasers for spectroscopy and LIDAR applications, respectively, as well as ultrastable CO2 lasers for coherent infrared radar.

Einsatz und Wirksamkeit von Systemtherapien bei Erwachsenen mit schwerer Neurodermitis: Erste Ergebnisse des deutschen Neurodermitis-Registers TREATgermany.

PubMed

Schmitt, Jochen; Abraham, Susanne; Trautmann, Freya; Stephan, Victoria; Fölster-Holst, Regina; Homey, Bernhard; Bieber, Thomas; Novak, Natalija; Sticherling, Michael; Augustin, Matthias; Kleinheinz, Andreas; Elsner, Peter; Weidinger, Stephan; Werfel, Thomas

2017-01-01

Versorgungsregister dienen der Erfassung des Einsatzes und der Wirksamkeit von Therapien unter realen Versorgungsbedingungen und sind als Basis einer evidenzbasierten Gesundheitsversorgung unverzichtbar. Das deutsche Neurodermitis-Register TREATgermany wurde als weltweit erstes Register für Patienten mit schwerer Neurodermitis 2011 initiiert. Erwachsene mit schwerer Neurodermitis (aktuelle/frühere antientzündliche Systemtherapie und/oder objektiver SCORAD ≥ 40) werden über einen Zeitraum von 24 Monaten prospektiv beobachtet. Anhand validierter Erhebungsinstrumente werden die klinische Erkrankungsschwere (EASI, SCORAD), Lebensqualität (DLQI), Symptome, globale Erkrankungsschwere sowie die Patientenzufriedenheit erfasst und die durchgeführten Therapien dokumentiert. Die vorliegende Analyse beschreibt die Charakteristika, Therapiewahl und Wirksamkeit der eingesetzten antiinflammatorischen Systemtherapien der bis Oktober 2014 eingeschlossenen Patienten. An fünf Zentren wurden insgesamt 78 Patienten (Durchschnittsalter 39 Jahre, 61 % männlich) eingeschlossen. Bei den Patienten besteht eine hohe Inanspruchnahme ambulanter und stationärer Leistungen. Ciclosporin war das am häufigsten eingesetzte Systemtherapeutikum und zeigte die höchste klinische Effektivität (EASI-50-Ansprechrate 51 %; EASI-75-Ansprechrate 34 % nach zwölfwöchiger Therapie). Azathioprin, Methotrexat (MTX), Prednisolon oral, Mycophenolat, Alitretinoin und Leflunomid wurden ebenfalls bei einzelnen Patienten eingesetzt. Die vorliegende Registerauswertung gibt wichtige Hinweise zur derzeitigen Versorgung von Erwachsenen mit schwerer Neurodermitis in Deutschland, dokumentiert die hohe Erkrankungslast, den Nutzen vorhandener Therapien und den Bedarf an weiteren, effektiven und in der Langzeitanwendung sicheren Therapieoptionen. © 2017 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

Interactive Web-Based and Hands-On Engineering Education: A Freshman Aerospace Design Course at MIT.

ERIC Educational Resources Information Center

Newman, Dava J.

"Introduction to Aerospace and Design" is a 3-hour per week freshman elective course at Massachusetts Institute of Technology (MIT) that culminates in a Lighter-Than-Air (LTA) vehicle design competition, exposing freshmen to the excitement of aerospace engineering design typically taught in the junior or senior years. In addition to the…

Identifikationsverfahren zur Analyse von EEG-Signalen bei Epilepsie mit Reaktions-Diffusions Netzwerken

NASA Astrophysics Data System (ADS)

Gollas, F.; Tetzlaff, R.

2007-06-01

Partielle Differentialgleichungen des Reaktions-Diffusions-Typs beschreiben Phänomene wie Musterbildung, nichtlineare Wellenausbreitung und deterministisches Chaos und werden oft zur Untersuchung komplexer Vorgänge auf den Gebieten der Biologie, Chemie und Physik herangezogen. Zellulare Nichtlineare Netzwerke (CNN) sind eine räumliche Anordnung vergleichsweise einfacher dynamischer Systeme, die eine lokale Kopplung untereinander aufweisen. Durch eine Diskretisierung der Ortsvariablen können Reaktions-Diffusions-Gleichungen häufig auf CNN mit nichtlinearen Gewichtsfunktionen abgebildet werden. Die resultierenden Reaktions-Diffusions-CNN (RD-CNN) weisen dann in ihrer Dynamik näherungsweise gleiches Verhalten wie die zugrunde gelegten Reaktions-Diffusions-Systeme auf. Werden RD-CNN zur Identifikation neuronaler Strukturen anhand von EEG-Signalen herangezogen, so besteht die Möglichkeit festzustellen, ob das gefundene Netzwerk lokale Aktivität aufweist. Die von Chua eingeführte Theorie der lokalen Aktivität Chua (1998); Dogaru und Chua (1998) liefert eine notwendige Bedingung für das Auftreten von emergentem Verhalten in zellularen Netzwerken. Änderungen in den Parametern bestimmter RD-CNN könnten auf bevorstehende epileptische Anfälle hinweisen. In diesem Beitrag steht die Identifikation neuronaler Strukturen anhand von EEG-Signalen durch Reaktions-Diffusions-Netzwerke im Vordergrund der dargestellten Untersuchungen. In der Ergebnisdiskussion wird insbesondere auch die Frage nach einer geeigneten Netzwerkstruktur mit minimaler Komplexität behandelt.

Generation of large-scale forest height and disturbance maps through the fusion of NISAR and GEDI along with TanDEM-X/L

NASA Astrophysics Data System (ADS)

Lei, Y.; Treuhaft, R. N.; Siqueira, P.; Torbick, N.; Lucas, R.; Keller, M. M.; Schmidt, M.; Ducey, M. J.; Salas, W.

2017-12-01

Large-scale products of forest height and disturbance are essential for understanding the global carbon distribution as well as its changes in response to natural events and human activities. Regarding this scientific need, both NASA's GEDI and NASA-ISRO's NISAR are going to be launched in the 2018-2021 timeframe in parallel with DLR's current TanDEM-X and/or the proposed TanDEM-L, which provides a lot of potential for global ecosystem mapping. A new simple and efficient method of forest height mapping has been developed for combining spaceborne repeat-pass InSAR and lidar missions (e.g. NISAR and GEDI) which estimates temporal decorrelation parameters of repeat-pass InSAR and uses the lidar data as training samples. An open-access Python-based software has been developed for automated processing. As a result, a mosaic of forest height was generated for US states of Maine and New Hampshire (11.6 million ha) using JAXA's ALOS-1 and ALOS-2 HV-pol InSAR data and a small piece of lidar training samples (44,000 ha) with the height estimates validated against airborne lidar and field inventory data over both flat and mountainous areas. In addition, through estimating and correcting for the temporal decorrelation effects in the spaceborne repeat-pass InSAR coherence data and also utilizing the spaceborne single-pass InSAR phase data, forest disturbance such as selective logging is not only detected but also quantified in subtropical forests of Australia using ALOS-1 HH-pol InSAR data (validated against NASA's Landsat), as well as in tropics of Brazil using TanDEM-X and ALOS-2 HH-pol InSAR data (validated against field inventory data). The operational simplicity and efficiency make these methods a potential observing/processing prototype for the fusion of NISAR, GEDI and TanDEM-X/L.

MIT Project Apophis: Surface Evaulation & Tomography (SET) Mission Study for the April 2029 Earth Encounter

NASA Astrophysics Data System (ADS)

Binzel, R. P.; Earle, A. M.; Vanatta, M.; Miller, D. W.

2017-12-01

Nature is providing a once-per-thousand year opportunity to study the geophysical outcome induced on an unprecedentedly large (350 meter) asteroid making an extremely close passage by the Earth (inside the distance of geosynchronous satellites) on Friday April 13, 2029. The aircraft carrier-sized (estimated 20 million metric ton) asteroid is named Apophis. While many previous spacecraft missions have studied asteroids, none has ever had the opportunity to study "live" the outcome of planetary tidal forces on their shapes, spin states, surface geology, and internal structure. Beyond the science interest directly observing this planetary process, the Apophis encounter provides an invaluable opportunity to gain knowledge for any eventuality of a known asteroid found to be on a certain impact trajectory. MIT's Project Apophis [1] is our response to nature's generous opportunity by developing a detailed mission concept for sending a spacecraft to orbit Apophis with the objectives of surveying its surface and interior structure before, during, and after its 2029 near-Earth encounter. The Surface Evaluation & Tomography (SET) mission concept we present is designed toward accomplishing three key science objectives: (1) bulk physical characterization, (2) internal structure, and (3) long-term orbit tracking. For its first mission objective, SET will study Apophis' bulk properties, including: shape, size, mass, volume, bulk density, surface geology, and composition, rotation rate, and spin state. The second mission objective is to characterize Apophis' internal structure before and after the encounter to determine its strength and cohesion - including tidally induced changes. Finally, the third objective studies the process of thermal re-radiation and consequential Yarkovsky drift, whose results will improve orbit predictions for Apophis as well as other potentially hazardous asteroids. [1] https://eapsweb.mit.edu/mit-project-apophis

The geomorphological evidences of subsidence in the Nile Delta: Analysis of high resolution topographic DEM and multi-temporal satellite images

NASA Astrophysics Data System (ADS)

El Bastawesy, M.; Cherif, O. H.; Sultan, M.

2017-12-01

This paper investigates the relevance of landforms to the subsidence of the Nile Delta using a high resolution topographic digital elevation model (DEM) and sets of multi-temporal Landsat satellite images. 195 topographic map sheets produced in 1946 at 1:25,000 scale were digitized, and the DEM was interpolated. The undertaken processing techniques have distinguished all the natural low-lying closed depressions from the artificial errors induced by the interpolation of the DEM. The local subsidence of these depressions from their surroundings reaches a maximum depth of 2.5 m. The regional subsidence of the Nile Delta has developed inverted topography, where the tracts occupied by the contemporary distributary channels are standing at higher elevations than the areas in between. This inversion could be related to the differences in the hydrological and sedimentological properties of underlying sediments, as the channels are underlain by water-saturated sands while the successions of clay and silt on flood plains are prone to compaction. Furthermore, the analysis of remote sensing and topographic data clearly show significant changes in the land cover and land use, particularly in the northern lagoons and adjacent sabkhas, which are dominated by numerous low subsiding depressions. The areas covered by water logging and ponds are increasing on the expense of agricultural areas, and aquaculture have been practiced instead. The precise estimation of subsidence rates and distribution should be worked out to evaluate probable changes in land cover and land use.

VizieR Online Data Catalog: The MIT-Green Bank 5GHz Survey (Bennett+, 1986-91)

NASA Astrophysics Data System (ADS)

Bennett, C. L.; Lawrence, C. R.; Burke, B. F.; Hewitt, J. N.; Mahoney, J.

2003-08-01

The MIT-Green Bank 5GHz survey catalog was produced from four separate surveys with the National Radio Astronomy Observatory (NRAO) 91m transit telescope (Bennett et al., 1986ApJS...61....1B (MG1); Langston et al., 1990ApJS...72..621L (MG2); Griffith et al., 1990ApJS...74..129G (MG3); Griffith et al. 1991ApJS...75..801G (MG4)). The sky coverage of the various surveys is: 00h < RAB < 24h, -00d30'13" < DECB < +19d29'47" for MG1; 04h < RAJ < 21h, +17.0d < DECJ < +39d09' for MG2; 16h30m < RAB < 05h, +17d < DECB < +39d09' for MG3; and 15h30m < RAB < 02h30m, +37.00d < DECB < +50d58'48" for MG4; where RAB and DECB refer to B1950 coordinates, and RAJ and DECJ refer to J2000 coordinates. The catalog contains 20344 sources detected with a signal-to-noise ratio greater than 5 and 3836 possible detections (MG1) with a signal-to-noise ratio less than 5. Spectral indices are computed for MG1 sources also identified in the Texas 365MHz survey (Douglas et al. 1980), and for MG1-MG4 sources also identified in the NRAO 1400MHz Survey (Condon and Broderick 1985). (1 data file).

VizieR Online Data Catalog: The MIT-Green Bank 5GHz Survey (Bennett+, 1986-91)

NASA Astrophysics Data System (ADS)

Bennett, C. L.; Lawrence, C. R.; Burke, B. F.; Hewitt, J. N.; Mahoney, J.

1999-04-01

The MIT-Green Bank 5 GHz survey catalog was produced from four separate surveys with the National Radio Astronomy Observatory (NRAO) 91m transit telescope (Bennett et al., 1986ApJS...61....1B (MG1); Langston et al., 1990ApJS...72..621L (MG2); Griffith et al., 1990ApJS...74..129G (MG3); Griffith et al. 1991ApJS...75..801G (MG4)). The sky coverage of the various surveys is: 00h < RAB < 24h, -00d30'13" < DECB < +19d29'47" for MG1; 04h < RAJ < 21h, +17.0d < DECJ < +39d09' for MG2; 16h30m < RAB < 05h, +17d < DECB < +39d09' for MG3; and 15h30m < RAB < 02h30m, +37.00d < DECB < +50d58'48" for MG4; where RAB and DECB refer to B1950 coordinates, and RAJ and DECJ refer to J2000 coordinates. The catalog contains 20344 sources detected with a signal-to-noise ratio greater than 5 and 3836 possible detections (MG1) with a signal-to-noise ratio less than 5. Spectral indices are computed for MG1 sources also identified in the Texas 365 MHz survey (Douglas et al. 1980), and for MG1-MG4 sources also identified in the NRAO 1400 MHz Survey (Condon and Broderick 1985). (1 data file).

Polymorphous Computing Architecture (PCA) Kernel Benchmark Measurements on the MIT Raw Microprocessor

DTIC Science & Technology

2006-06-14

Robert Graybill . A Raw hoard for the use of this project was provided by the Computer Architecture Croup at the Massachusetts Institute of Technology...simulator is presented by MIT as being an accurate model of the Raw chip, we have found that it does not accurately model the board. Our comparison...G4 processor, model 7410. with a 32 kbyte level-1 cache on-chip and a 2 Mbyte L2 cache connected through a 250 MH/ bus [12]. Each node has 256 Mbyte

Trouble and Triumph: German Life-Turkish Tradition in Renan Demirkan's "Schwarzer Tee mit drei Stuck Zucker"

ERIC Educational Resources Information Center

Ebert, Reika

2004-01-01

This paper explores Demirkan's narrative strategies in "Schwarzer Tee mit drei Stuck Zucker" to negotiate issues of a life between two cultures and traditions. Based on Bhabha's insights that mainstream culture needs intellectual and artistic infusion from the margins of a society in order to remain vital; and that cultural production…

How Much Have They Retained? Making Unseen Concepts Seen in a Freshman Electromagnetism Course at MIT

ERIC Educational Resources Information Center

Dori, Yehudit Judy; Hult, Erin; Breslow, Lori; Belcher, John W.

2007-01-01

The introductory freshmen electromagnetism course at MIT has been taught since 2000 using a studio physics format entitled TEAL--Technology Enabled Active Learning. TEAL has created a collaborative, hands-on environment where students carry out desktop experiments, submit web-based assignments, and have access to a host of visualizations and…

Excellence in Research: Creative Organizational Responses at Berkeley, Harvard, MIT, and Stanford. ASHE 1985 Annual Meeting Paper.

ERIC Educational Resources Information Center

Gardiner, John J.

Research environments of four leading universities were studied: University of California at Berkeley (UC-Berkeley), Harvard University, Massachusetts Institute of Technology (MIT), and Stanford University. Attention was directed to organizational responses for encouraging collaboration in research at these leading universities, as well as to…

MARE2DEM: a 2-D inversion code for controlled-source electromagnetic and magnetotelluric data

NASA Astrophysics Data System (ADS)

Key, Kerry

2016-10-01

This work presents MARE2DEM, a freely available code for 2-D anisotropic inversion of magnetotelluric (MT) data and frequency-domain controlled-source electromagnetic (CSEM) data from onshore and offshore surveys. MARE2DEM parametrizes the inverse model using a grid of arbitrarily shaped polygons, where unstructured triangular or quadrilateral grids are typically used due to their ease of construction. Unstructured grids provide significantly more geometric flexibility and parameter efficiency than the structured rectangular grids commonly used by most other inversion codes. Transmitter and receiver components located on topographic slopes can be tilted parallel to the boundary so that the simulated electromagnetic fields accurately reproduce the real survey geometry. The forward solution is implemented with a goal-oriented adaptive finite-element method that automatically generates and refines unstructured triangular element grids that conform to the inversion parameter grid, ensuring accurate responses as the model conductivity changes. This dual-grid approach is significantly more efficient than the conventional use of a single grid for both the forward and inverse meshes since the more detailed finite-element meshes required for accurate responses do not increase the memory requirements of the inverse problem. Forward solutions are computed in parallel with a highly efficient scaling by partitioning the data into smaller independent modeling tasks consisting of subsets of the input frequencies, transmitters and receivers. Non-linear inversion is carried out with a new Occam inversion approach that requires fewer forward calls. Dense matrix operations are optimized for memory and parallel scalability using the ScaLAPACK parallel library. Free parameters can be bounded using a new non-linear transformation that leaves the transformed parameters nearly the same as the original parameters within the bounds, thereby reducing non-linear smoothing effects. Data

Anbindung des SISIS-SunRise-Bibliothekssystems an das zentrale Identitätsmanagement

NASA Astrophysics Data System (ADS)

Ebner, Ralf; Pretz, Edwin

Wir berichten über Konzepte und Implementierungen zur Datenprovisionierung aus den Personenverwaltungssystemen der Technischen Universität München (TUM) über das zentrale Metadirectory am Leibniz-Rechenzentrum (LRZ) in das SISIS-SunRise-Bibliothekssystem der Universitätsbibliothek der TUM (TUB). Es werden drei Implementierungsvarianten diskutiert, angefangen von der Generierung und Übertragung einfacher CSV-Dateien über ein OpenLDAP-basiertes Konzept als Backend für die SISIS-Datenbank bis zur endgültigen Implementierung mit dem OCLC IDM Connector.

DEM L241, A SUPERNOVA REMNANT CONTAINING A HIGH-MASS X-RAY BINARY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seward, F. D.; Charles, P. A.; Foster, D. L.

2012-11-10

A Chandra observation of the Large Magellanic Cloud supernova remnant DEM L241 reveals an interior unresolved source which is probably an accretion-powered binary. The optical counterpart is an O5III(f) star making this a high-mass X-ray binary with an orbital period likely to be of the order of tens of days. Emission from the remnant interior is thermal and spectral information is used to derive density and mass of the hot material. Elongation of the remnant is unusual and possible causes of this are discussed. The precursor star probably had mass >25 M {sub Sun}.

STF Optimierung von single-bit CT ΣΔ Modulatoren basierend auf skalierten Filterkoeffizienten

NASA Astrophysics Data System (ADS)

Widemann, C.; Zorn, C.; Brückner, T.; Ortmanns, M.; Mathis, W.

2012-09-01

Die vorliegende Arbeit beschäftigt sich mit dem Signalübertragungsverhalten von single-bit continuous-time (CT) ΣΔ Modulatoren. Dabei liegt der Fokus der Untersuchung auf dem Peaking der Signaltransferfunktion (STF). Dieser Effekt kann die Performance und die Stabilität des Gesamtsystems negativ beeinflussen, da bei auftretendem STF-Peaking Signale außerhalb des Signalbands verstärkt werden. In dieser Arbeit wird ein neuer Ansatz zur Reduktion des Peakings vorgestellt, der auf der Optimierung der Systemdynamik basiert. Dabei werden die Filterkoeffizienten des Modulators systematisch angepasst. Anhand eines Beispielsystems wird gezeigt, dass der Ansatz genutzt werden kann, um das Übertragungsverhalten des Modulators abhängig vom Ausgangssystem zu verändern. So kann entweder die Systemsperformance verbessert werden, ohne Peaking in der STF zu erzeugen, oder das STF-Peaking reduziert werden, ohne die Systemperformance stark zu beeinflussen.

Ustekinumab in der Therapie der Pustulosis palmoplantaris - Eine Fallserie mit neun Patienten.

PubMed

Buder, Valeska; Herberger, Katharina; Jacobi, Arnd; Augustin, Matthias; Radtke, Marc Alexander

2016-11-01

Die Pustulosis palmoplantaris ist eine chronisch entzündliche Hauterkrankung, die mit bedeutenden Einschränkungen der Lebensqualität und der Belastbarkeit einhergeht. Aufgrund von Zulassungsbeschränkungen und einem häufig therapierefraktären Verlauf sind die Behandlungsmöglichkeiten limitiert. Nach zuvor frustranen Therapien erhielten 9 Patienten mit Pustulosis palmoplantaris nach Ausschluss einer latenten Tuberkulose Ustekinumab (45 mg Ustekinumab bei < 100 kg Körpergewicht [KG], 90 mg Ustekinumab > 100 kg KG) in Woche 0, 4, 12 und 24. Reguläre Visiten erfolgten nach 4 und 12 Wochen, im weiteren Verlauf alle 12 Wochen. Das Durchschnittsalter bei Therapiebeginn betrug 48 Jahre. Drei Patienten waren männlich. Bei n  =  4 Patienten (44,4 %) wurde eine Verbesserung um 75 % des Palmoplantar-Psoriasis-Area-Severity-Index (PPPASI) erreicht. Insgesamt verbesserte sich der PPPASI nach 24 Wochen durchschnittlich um 71,6 %. Eine komplette Abheilung zeigte sich bei n  =  2 Patienten nach 24 Wochen. Bis auf lokale Injektionsreaktionen und leichte Infekte wurden keine unerwünschten Wirkungen beobachtet. Die Fallserie ist ein weiterer Beleg für die Wirksamkeit und Verträglichkeit von Ustekinumab in der Therapie der Pustulosis palmoplantaris. Zur Beurteilung der Langzeitwirkung und -sicherheit sowie der Wirksamkeit einer intermittierenden Therapie sind kontrollierte Studiendaten sowie Beobachtungen im Rahmen von Patientenregistern notwendig. © 2016 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

Statistik in Naturwissenschaft und Technik

NASA Astrophysics Data System (ADS)

Wilrich, Peter-Theodor

Mit dem Aufschwung von Naturwissenschaft und Technik zu Beginn des 19. Jahrhunderts entstand die mathematische Statistik, angeregt aus der Geodäsie (wie die Methode der kleinsten Quadrate) und der Anthropologie (wie die statistische Analyse mehrdimensionaler Beobachtungen und ihrer stochastischen Abhängigkeiten). Im Gegensatz zu den Wirtschafts- und Sozialwissenschaften, in denen Daten vorwiegend aus Beobachtungsstudien gewonnen werden, stehen in den Naturwissenschaften Experimente im Vordergrund. Daher gehört die statistische Versuchsplanung zu den insbesondere in Naturwissenschaft und Technik angewendeten statistischen Methoden, aber auch die Extremwertstatistik und Lebensdaueranalysen sowie die Methoden der räumlichen Statistik (insbesondere in der Umweltforschung). Im 20. Jahrhundert wurden Stichprobenpläne und Regelkarten (Kontrollkarten) zur Prozessregelung als Hilfsmittel der statistischen Qualitätssicherung entwickelt. Diese Methodenbündel, mit denen sich der Ausschuss Statistik in Naturwissenschaft und Technik immer wieder befasst, werden im Folgenden vorgestellt.

Individuelle Templates für Rekonstruktionen des linken Herzventrikels

NASA Astrophysics Data System (ADS)

Feder, Stefan; Falk, Volkmar; Gutberiet, Matthias; Bartz, Dirk

Bei krankhaften Vergrößerungen des linken Herzventrikels kann eine chirurgische Ventrikelrekonstruktion zur Verbesserung der Herzleistung beitragen. Die dabei erstellte Ventrikelgeometrie ist von entscheidender Bedeutung. Diese Studie befasst sich mit der computerbasierten Planung von individuellen Schablonen (Templates) für Ventrikelrekonstruktionen. Ziel ist es aus Cardio-CT-Daten, präoperativ, patientenindividuelle 3D-Modelle für Ventrikeltemplates zu erstellen. Hierfür wird aus CT-Daten der linksventrikuläre Blutpool segmentiert und daraus das Ventrikeltemplate modelliert. Dies geschieht anhand von zwei Kriterien: dem physiologischen Ventrikelfüllungsvolumen und der hämodynamisch günstigen ellipsoiden Form. Es konnten 20 3D-Templatemodelle mit einem durchschnittlichen Volumen von 144 ml erstellt werden. Die ellipsoide Form konnte durch manuelle Modellierung erreicht werden. Der Nachweis verbesserter Operationsergebnisse muss in nachfolgenden klinischen Studien erbracht werden.

Semi-automated extraction of landslides in Taiwan based on SPOT imagery and DEMs

NASA Astrophysics Data System (ADS)

Eisank, Clemens; Hölbling, Daniel; Friedl, Barbara; Chen, Yi-Chin; Chang, Kang-Tsung

2014-05-01

The vast availability and improved quality of optical satellite data and digital elevation models (DEMs), as well as the need for complete and up-to-date landslide inventories at various spatial scales have fostered the development of semi-automated landslide recognition systems. Among the tested approaches for designing such systems, object-based image analysis (OBIA) stepped out to be a highly promising methodology. OBIA offers a flexible, spatially enabled framework for effective landslide mapping. Most object-based landslide mapping systems, however, have been tailored to specific, mainly small-scale study areas or even to single landslides only. Even though reported mapping accuracies tend to be higher than for pixel-based approaches, accuracy values are still relatively low and depend on the particular study. There is still room to improve the applicability and objectivity of object-based landslide mapping systems. The presented study aims at developing a knowledge-based landslide mapping system implemented in an OBIA environment, i.e. Trimble eCognition. In comparison to previous knowledge-based approaches, the classification of segmentation-derived multi-scale image objects relies on digital landslide signatures. These signatures hold the common operational knowledge on digital landslide mapping, as reported by 25 Taiwanese landslide experts during personal semi-structured interviews. Specifically, the signatures include information on commonly used data layers, spectral and spatial features, and feature thresholds. The signatures guide the selection and implementation of mapping rules that were finally encoded in Cognition Network Language (CNL). Multi-scale image segmentation is optimized by using the improved Estimation of Scale Parameter (ESP) tool. The approach described above is developed and tested for mapping landslides in a sub-region of the Baichi catchment in Northern Taiwan based on SPOT imagery and a high-resolution DEM. An object

Effect of DEM resolution on rainfall-triggered landslide modeling within a triangulated network-based model. A case study in the Luquillo Forest, Puerto Rico

NASA Astrophysics Data System (ADS)

Arnone, E.; Dialynas, Y. G.; Noto, L. V.; Bras, R. L.

2013-12-01

Catchment slope distribution is one of the topographic characteristics that significantly control rainfall-triggered landslide modeling, in both direct and indirect ways. Slope directly determines the soil volume associated with instability. Indirectly slope also affects the subsurface lateral redistribution of soil moisture across the basin, which in turn determines the water pore pressure conditions that impact slope stability. In this study, we investigate the influence of DEM resolution on slope stability and the slope stability analysis by using a distributed eco-hydrological and landslide model, the tRIBS-VEGGIE (Triangulated Irregular Network (TIN)-based Real-time Integrated Basin Simulator - VEGetation Generator for Interactive Evolution). The model implements a triangulated irregular network to describe the topography, and it is capable of evaluating vegetation dynamics and predicting shallow landslides triggered by rainfall. The impact of DEM resolution on the landslide prediction was studied using five TINs derived from five grid DEMs at different resolutions, i.e. 10, 20, 30, 50 and 70 m respectively. The analysis was carried out on the Mameyes Basin, located in the Luquillo Experimental Forest in Puerto Rico, where previous landslide analyses have been carried out. Results showed that the use of the irregular mesh reduced the loss of accuracy in the derived slope distribution when coarser resolutions were used. The impact of the different resolutions on soil moisture patterns was important only when the lateral redistribution was considerable, depending on hydrological properties and rainfall forcing. In some cases, the use of different DEM resolutions did not significantly affect tRIBS-VEGGIE landslide output, in terms of landslide locations, and values of slope and soil moisture at failure.

OOPS, Turning MIT Opencourseware into Chinese: An Analysis of a Community of Practice of Global Translators

ERIC Educational Resources Information Center

Lee, Mimi Miyoung; Lin, Meng-Fen Grace; Bonk, Curtis J.

2007-01-01