Formation of BaSi2 heterojunction solar cells using transparent MoOx hole transport layers

NASA Astrophysics Data System (ADS)

Du, W.; Takabe, R.; Baba, M.; Takeuchi, H.; Hara, K. O.; Toko, K.; Usami, N.; Suemasu, T.

2015-03-01

Heterojunction solar cells that consist of 15 nm thick molybdenum trioxide (MoOx, x < 3) as a hole transport layer and 600 nm thick unpassivated or passivated n-BaSi2 layers were demonstrated. Rectifying current-voltage characteristics were observed when the surface of BaSi2 was exposed to air. When the exposure time was decreased to 1 min, an open circuit voltage of 200 mV and a short circuit current density of 0.5 mA/cm2 were obtained under AM1.5 illumination. The photocurrent density under a reverse bias voltage of -1 V reached 25 mA/cm2, which demonstrates the significant potential of BaSi2 for solar cell applications.

75 FR 6162 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-9-81 (MD-81), DC-9-82 (MD-82...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-08

... Corporation Model DC- 9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), and MD-88 Airplanes... Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), and MD-88 airplanes. This...., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service...

Structure and transport in high pressure oxygen sputter-deposited BaSnO{sub 3−δ}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ganguly, Koustav; Ambwani, Palak; Xu, Peng

BaSnO{sub 3} has recently been identified as a high mobility wide gap semiconductor with significant potential for room temperature oxide electronics. Here, a detailed study of the high pressure oxygen sputter-deposition, microstructure, morphology, and stoichiometry of epitaxial BaSnO{sub 3} on SrTiO{sub 3}(001) and MgO(001) is reported, optimized conditions resulting in single-phase, relaxed, close to stoichiometric films. Most significantly, vacuum annealing is established as a facile route to n-doped BaSnO{sub 3−δ}, leading to electron densities above 10{sup 19} cm{sup −3}, 5 mΩ cm resistivities, and room temperature mobility of 20 cm{sup 2} V{sup −1} s{sup −1} in 300-Å-thick films on MgO(001).more » Mobility limiting factors, and the substantial scope for their improvement, are discussed.« less

Apple (Malus domestica) MdERF2 negatively affects ethylene biosynthesis during fruit ripening by suppressing MdACS1 transcription.

PubMed

Li, Tong; Jiang, Zhongyu; Zhang, Lichao; Tan, Dongmei; Wei, Yun; Yuan, Hui; Li, Tianlai; Wang, Aide

2016-12-01

Ripening in climacteric fruit requires the gaseous phytohormone ethylene. Although ethylene signaling has been well studied, knowledge of the transcriptional regulation of ethylene biosynthesis is still limited. Here we show that an apple (Malus domestica) ethylene response factor, MdERF2, negatively affects ethylene biosynthesis and fruit ripening by suppressing the transcription of MdACS1, a gene that is critical for biosynthesis of ripening-related ethylene. Expression of MdERF2 was suppressed by ethylene during ripening of apple fruit, and we observed that MdERF2 bound to the promoter of MdACS1 and directly suppressed its transcription. Moreover, MdERF2 suppressed the activity of the promoter of MdERF3, a transcription factor that we found to bind to the MdACS1 promoter, thereby increasing MdACS1 transcription. We determined that the MdERF2 and MdERF3 proteins directly interact, and this interaction suppresses the binding of MdERF3 to the MdACS1 promoter. Moreover, apple fruit with transiently downregulated MdERF2 expression showed higher ethylene production and faster ripening. Our results indicate that MdERF2 negatively affects ethylene biosynthesis and fruit ripening in apple by suppressing the transcription of MdACS1 via multiple mechanisms, thereby acting as an antagonist of positive ripening regulators. Our findings offer a deep understanding of the transcriptional regulation of ethylene biosynthesis during climacteric fruit ripening. © 2016 The Authors The Plant Journal © 2016 John Wiley & Sons Ltd.

Effect of BaSi2 template growth duration on the generation of defects and performance of p-BaSi2/n-Si heterojunction solar cells

NASA Astrophysics Data System (ADS)

Yachi, Suguru; Takabe, Ryota; Deng, Tianguo; Toko, Kaoru; Suemasu, Takashi

2018-04-01

We investigated the effect of BaSi2 template growth duration (t RDE = 0-20 min) on the defect generation and performance of p-BaSi2/n-Si heterojunction solar cells. The p-BaSi2 layer grown by molecular beam epitaxy (MBE) was 15 nm thick with a hole concentration of 2 × 1018 cm-3. The conversion efficiency η increased for films grown at long t RDE, owing to improvements of the open-circuit voltage (V OC) and fill factor (FF), reaching a maximum of η = 8.9% at t RDE = 7.5 min. However, η decreased at longer and shorter t RDE owing to lower V OC and FF. Using deep-level transient spectroscopy, we detected a hole trap level 190 meV above the valence band maximum for the sample grown without the template (t RDE = 0 min). An electron trap level 106 meV below the conduction band minimum was detected for a sample grown with t RDE = 20 min. The trap densities for both films were (1-2) × 1013 cm-3. The former originated from the diffusion of Ba into the n-Si region; the latter originated from defects in the template layer. The crystalline qualities of the template and MBE-grown layers were discussed. The root-mean-square surface roughness of the template reached a minimum of 0.51 nm at t RDE = 7.5 min. The a-axis orientation of p-BaSi2 thin films degraded as t RDE exceeded 10 min. In terms of p-BaSi2 crystalline quality and solar cell performance, the optimum t RDE was determined to be 7.5 min, corresponding to approximately 4 nm in thickness.

Melt growth and properties of bulk BaSnO3 single crystals

NASA Astrophysics Data System (ADS)

Galazka, Z.; Uecker, R.; Irmscher, K.; Klimm, D.; Bertram, R.; Kwasniewski, A.; Naumann, M.; Schewski, R.; Pietsch, M.; Juda, U.; Fiedler, A.; Albrecht, M.; Ganschow, S.; Markurt, T.; Guguschev, C.; Bickermann, M.

2017-02-01

We present the first-time growth of bulk BaSnO3 single crystals from the melt by direct solidification, their basic electrical and optical properties as well as their structural quality. Our measurement of the melting point (MP) of BaSnO3 amounts to 1855 °C  ±  25 K. At this temperature an intensive decomposition and non-stoichiometric evaporation takes place as the partial pressure of SnO(g) is about 90 times higher than that of BaO(g). X ray powder diffraction identified only the BaSnO3 perovskite phase, while narrow rocking curves having a full width at half maximum of 26 arcsec and etch pit densities below 106 cm-2 confirm a high degree of structural perfection of the single crystals. In this respect they surpass the structural properties of those single crystals that were reported in the literature. The electrical conductivity of nominally undoped crystals depends on the growth conditions and ranges from insulating to medium n-type conductivity. After post-growth annealing in an oxidizing atmosphere undoped crystals are generally insulating. Doping the crystals with lanthanum during growth results in a high n-type conductivity. For a La doping concentration of 0.123 wt.% we measured an electron concentration of 3.3  ×  1019 cm-3 and an electron mobility of 219 cm2 V-1 s-1. Based on optical absorption measurements we determined an energy of 3.17  ±  0.04 eV at 5 K and of 2.99  ±  0.04 eV at 297 K for the indirect band gap of BaSnO3.

An Apple Protein Kinase MdSnRK1.1 Interacts with MdCAIP1 to Regulate ABA Sensitivity.

PubMed

Liu, Xiao-Juan; Liu, Xin; An, Xiu-Hong; Han, Peng-Liang; You, Chun-Xiang; Hao, Yu-Jin

2017-10-01

ABA is a crucial phytohormone for development and stress responses in plants. Snf1-related protein kinase 1.1 (SnRK1.1) is involved in the ABA response. However, the molecular mechanism underlying the SnRK1.1 response to ABA is largely unknown. Here, it was found that overexpression of the apple MdSnRK1.1 gene enhanced ABA sensitivity in both transgenic apple calli and Arabidopsis seedlings. Subsequently, a yeast two-hybrid screen demonstrated that MdCAIP1 (C2-domain ABA Insensitive Protein1) interacted with MdSnRK1.1. Their interaction was further confirmed by pull-down and co-immunoprecipitation assays. Expression of the MdCAIP1 gene was positively induced by ABA. Its overexpression enhanced ABA sensitivity in transgenic apple calli. Furthermore, it was found that MdSnRK1.1 phosphorylated the MdCAIP1 protein in vivo and promoted its degradation in vitro and in vivo. As a result, MdSnRK1.1 inhibited MdCAIP1-mediated ABA sensitivity, and MdCAIP1 partially reduced MdSnRK1.1-mediated ABA sensitivity. Our findings indicate that MdSnRK1.1 plays an important role in the ABA response, partially by controlling the stability of the MdCAIP1 protein. © The Author 2017. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Apple RING E3 ligase MdMIEL1 inhibits anthocyanin accumulation by ubiquitinating and degrading MdMYB1 protein.

PubMed

An, Jian-Ping; Liu, Xin; Li, Hao-Hao; You, Chun-Xiang; Wang, Xiao-Fei; Hao, Yu-Jin

2017-11-01

MdMYB1 is an important regulator for anthocyanin accumulation in apple (Malus × domestica). Here, an apple RING E3 ligase, MdMIEL1, was screened out as a partner of MdMYB1 with a yeast two-hybrid approach. Pull-down, bimolecular fluorescence complementation and coimmunoprecipitation assays further verified the interaction between MdMIEL1 and MdMYB1 proteins. Subsequently, in vitro and in vivo experiments indicated that MdMIEL1 functioned as a ubiquitin E3 ligase to ubiquitinate MdMYB1 protein, followed by degradation through a 26S proteasome pathway. Furthermore, transgenic studies in apple calli and Arabidopsis demonstrated that MdMIEL1 negatively regulated anthocyanin accumulation by modulating the degradation of MdMYB1 protein. Taken together, our findings provide a new insight into the molecular mechanism by which MdMIEL1 negatively regulates anthocyanin biosynthesis by ubiquitinating and degrading MdMYB1 protein. © The Author 2017. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Size-dependent disproportionation (in 2-20 nm regime) and hybrid Bond Valence derived interatomic potentials for BaTaO2N

NASA Astrophysics Data System (ADS)

Anbalagan, Kousika; Thomas, Tiju

2018-05-01

Interatomic potentials for complex materials (like ceramic systems) are important for realistic molecular dynamics (MD) simulations. Such simulations are relevant for understanding equilibrium, transport and dynamical properties of materials, especially in the nanoregime. Here we derive a hybrid interatomic potential (based on bond valence (BV) derived Morse and Coulomb terms), for modeling a complex ceramic, barium tantalum oxynitride (BaTaO2N). This material has been chosen due to its relevance for capacitive and photoactive applications. However, the material presents processing challenges such as the emergence of non-stoichiometric phases during processing, demonstrating complex processing-property correlations. This makes MD investigations of this material both scientifically and technologically relevant. The BV based hybrid potential presented here has been used for simulating sintering of BaTaO2N nanoparticles ( 2-20 nm) under different conditions (using the relevant canonical ensemble). Notably, we show that sintering of particles of diameter < 10 nm requires no external sintering aids such as the addition of barium sources (since stoichiometry is preserved during heat treatment in this size regime). Also, we observe that sintering of particles > 10 nm in size results in the formation of a cluster of tantalum and oxygen atoms at the interface of the BaTaO2N particles. This is in agreement with the experimental reports. The results presented here suggest that the potential proposed can be used to explore dynamical properties of BaTaO2N and related systems. This work will also open avenues for development of nanoscience-enabled aid-free sintering approaches to this and related materials.

A novel matrix dispersion based on phospholipid complex for improving oral bioavailability of baicalein: preparation, in vitro and in vivo evaluations.

PubMed

Zhou, Yang; Dong, Wujun; Ye, Jun; Hao, Huazhen; Zhou, Junzhuo; Wang, Renyun; Liu, Yuling

2017-11-01

Phospholipid complex is one of the most successful approaches for enhancing oral bioavailability of poorly absorbed plant constituents. But the sticky property of phospholipids results in an unsatisfactory dissolution of drugs. In this study, a matrix dispersion of baicalein based on phospholipid complex (BaPC-MD) was first prepared by a discontinuous solvent evaporation method, in which polyvinylpyrrolidone-K30 (PVP-K30) was employed for improving the dispersibility of baicalein phospholipid complex (BaPC) and increasing dissolution of baicalein. The combination ratio of baicalein and phospholipids in BaPC-MD was 99.39% and baicalein was still in a complete complex state with phospholipid in BaPC-MD. Differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier Transform Infrared (FTIR) analyzes demonstrated that baicalein was fully transformed to an amorphous state in BaPC-MD and phospholipid complex formed. The water-solubility and n-octanol solubility of baicalein in BaPC-MD significantly increased compared with those of pure baicalein. Compared with baicalein and BaPC, the cumulative dissolution of BaPC-MD at 120 min increased 2.77- and 1.23-fold, respectively. In vitro permeability study in Caco-2 cells indicated that the permeability of BaPC-MD was remarkably higher than those of baicalein and BaPC. Pharmacokinetic study showed that the average C max of BaPC-MD was significantly increased compared to baicalein and BaPC. AUC 0-14 h of BaPC-MD was 5.01- and 1.91-fold of baicalein and BaPC, respectively. The novel BaPC-MD significantly enhanced the oral bioavailability of baicalein by improving the dissolution and permeability of baicalein without destroying the complexation state of baicalein and phospholipids. The current drug delivery system provided an optimal strategy to significantly enhance oral bioavailability for poorly water-soluble drugs.

MdSOS2L1 phosphorylates MdVHA-B1 to modulate malate accumulation in response to salinity in apple.

PubMed

Hu, Da-Gang; Sun, Cui-Hui; Sun, Mei-Hong; Hao, Yu-Jin

2016-03-01

Salt-induced phosphorylation of MdVHA-B1 protein was mediated by MdSOS2L1 protein kinase, and thereby increasing malate content in apple. Salinity is an important environmental factor that influences malate accumulation in apple. However, the molecular mechanism by which salinity regulates this process is poorly understood. In this work, we found that MdSOS2L1, a novel AtSOS2-LIKE protein kinase, interacts with V-ATPase subunit MdVHA-B1. Furthermore, MdSOS2L1 directly phosphorylates MdVHA-B1 at Ser(396) site to modulate malate accumulation in response to salt stress. Meanwhile, a series of transgenic analyses in apple calli showed that the MdSOS2L1-MdVHAB1 pathway was involved in the regulation of malate accumulation. Finally, a viral vector-based transformation approach demonstrated that the MdSOS2L1-MdVHAB1 pathway also modulated malate accumulation in apple fruits with or without salt stress. Collectively, our findings provide a new insight into the mechanism by which MdSOS2L1 phosphorylates MdVHA-B1 to modulate malate accumulation in response to salinity in apple.

Md-miR156ab and Md-miR395 Target WRKY Transcription Factors to Influence Apple Resistance to Leaf Spot Disease.

PubMed

Zhang, Qiulei; Li, Yang; Zhang, Yi; Wu, Chuanbao; Wang, Shengnan; Hao, Li; Wang, Shengyuan; Li, Tianzhong

2017-01-01

MicroRNAs (miRNAs) are key regulators of gene expression that post-transcriptionally regulate transcription factors involved in plant physiological activities. Little is known about the effects of miRNAs in disease resistance in apple ( Malus × domestica ). We globally profiled miRNAs in the apple cultivar Golden Delicious (GD) infected or not with the apple leaf spot fungus Alternaria alternaria f. sp. mali (ALT1), and identified 58 miRNAs that exhibited more than a 2-fold upregulation upon ALT1 infection. We identified a pair of miRNAs that target protein-coding genes involved in the defense response against fungal pathogens; Md-miR156ab targets a novel WRKY transcription factor, MdWRKYN1, which harbors a TIR and a WRKY domain. Md-miR395 targets another transcription factor, MdWRKY26, which contains two WRKY domains. Real-time PCR analysis showed that Md-miR156ab and Md-miR395 levels increased, while MdWRKYN1 and MdWRKY26 expression decreased in ALT1-inoculated GD leaves; furthermore, the overexpression of Md-miR156ab and Md-miR395 resulted in a significant reduction in MdWRKYN1 and MdWRKY26 expression. To investigate whether these miRNAs and their targets play a crucial role in plant defense, we overexpressed MdWRKYN1 or knocked down Md-miR156ab activity, which in both cases enhanced the disease resistance of the plants by upregulating the expression of the WRKY-regulated pathogenesis-related (PR) protein-encoding genes MdPR3-1, MdPR3-2, MdPR4, MdPR5, MdPR10-1 , and MdPR10-2 . In a similar analysis, we overexpressed MdWRKY26 or suppressed Md-miR395 activity, and found that many PR protein-encoding genes were also regulated by MdWRKY26 . In GD, ALT-induced Md-miR156ab and Md-miR395 suppress MdWRKYN1 and MdWRKY26 expression, thereby decreasing the expression of some PR genes, and resulting in susceptibility to ALT1.

Over 15 MA/cm2 of critical current density in 4.8 µm thick, Zr-doped (Gd,Y)Ba2Cu3Ox superconductor at 30 K, 3T.

PubMed

Majkic, Goran; Pratap, Rudra; Xu, Aixia; Galstyan, Eduard; Selvamanickam, Venkat

2018-05-03

An Advanced MOCVD (A-MOCVD) reactor was used to deposit 4.8 µm thick (Gd,Y)BaCuO tapes with 15 mol% Zr addition in a single pass. A record-high critical current density (J c ) of 15.11 MA/cm 2 has been measured over a bridge at 30 K, 3T, corresponding to an equivalent (I c ) value of 8705 A/12 mm width. This corresponds to a lift factor in critical current of ~11 which is the highest ever reported to the best of author's knowledge. The measured critical current densities at 3T (B||c) and 30, 40 and 50 K, respectively, are 15.11, 9.70 and 6.26 MA/cm 2 , corresponding to equivalent Ic values of 8705, 5586 and 3606 A/12 mm and engineering current densities (J e ) of 7068, 4535 and 2928 A/mm 2 . The engineering current density (J e ) at 40 K, 3T is 7 times higher than that of the commercial HTS tapes available with 7.5 mol% Zr addition. Such record-high performance in thick films (>1 µm) is a clear demonstration that growing thick REBCO films with high critical current density (J c ) is possible, contrary to the usual findings of strong J c degradation with film thickness. This achievement was possible due to a combination of strong temperature control and uniform laminar flow achieved in the A-MOCVD system, coupled with optimization of BaZrO 3 nanorod growth parameters.

Spin-Coating and Characterization of Multiferroic MFe2O4 (M=Co, Ni) / BaTiO3 Bilayers

NASA Astrophysics Data System (ADS)

Quandt, Norman; Roth, Robert; Syrowatka, Frank; Steimecke, Matthias; Ebbinghaus, Stefan G.

2016-01-01

Bilayer films of MFe2O4 (M=Co, Ni) and BaTiO3 were prepared by spin coating of N,N-dimethylformamide/acetic acid solutions on platinum coated silicon wafers. Five coating steps were applied to get the desired thickness of 150 nm for both the ferrite and perovskite layer. XRD, IR and Raman spectroscopy revealed the formation of phase-pure ferrite spinels and BaTiO3. Smooth surfaces with roughnesses in the order of 3 to 5 nm were found in AFM investigations. Saturation magnetization of 347 emu cm-3 for the CoFe2O4/BaTiO3 and 188 emu cm-3 for the NiFe2O4/BaTiO3 bilayer, respectively were found. For the CoFe2O4/BaTiO3 bilayer a strong magnetic anisotropy was observed with coercivity fields of 5.1 kOe and 3.3 kOe (applied magnetic field perpendicular and parallel to film surface), while for the NiFe2O4/BaTiO3 bilayer this effect is less pronounced. Saturated polarization hysteresis loops prove the presence of ferroelectricity in both systems.

Partially Glycosylated Dendrimers Block MD-2 and Prevent TLR4-MD-2-LPS Complex Mediated Cytokine Responses

PubMed Central

Barata, Teresa S.; Teo, Ian; Brocchini, Steve; Zloh, Mire; Shaunak, Sunil

2011-01-01

The crystal structure of the TLR4-MD-2-LPS complex responsible for triggering powerful pro-inflammatory cytokine responses has recently become available. Central to cell surface complex formation is binding of lipopolysaccharide (LPS) to soluble MD-2. We have previously shown, in biologically based experiments, that a generation 3.5 PAMAM dendrimer with 64 peripheral carboxylic acid groups acts as an antagonist of pro-inflammatory cytokine production after surface modification with 8 glucosamine molecules. We have also shown using molecular modelling approaches that this partially glycosylated dendrimer has the flexibility, cluster density, surface electrostatic charge, and hydrophilicity to make it a therapeutically useful antagonist of complex formation. These studies enabled the computational study of the interactions of the unmodified dendrimer, glucosamine, and of the partially glycosylated dendrimer with TLR4 and MD-2 using molecular docking and molecular dynamics techniques. They demonstrate that dendrimer glucosamine forms co-operative electrostatic interactions with residues lining the entrance to MD-2's hydrophobic pocket. Crucially, dendrimer glucosamine interferes with the electrostatic binding of: (i) the 4′phosphate on the di-glucosamine of LPS to Ser118 on MD-2; (ii) LPS to Lys91 on MD-2; (iii) the subsequent binding of TLR4 to Tyr102 on MD-2. This is followed by additional co-operative interactions between several of the dendrimer glucosamine's carboxylic acid branches and MD-2. Collectively, these interactions block the entry of the lipid chains of LPS into MD-2's hydrophobic pocket, and also prevent TLR4-MD-2-LPS complex formation. Our studies have therefore defined the first nonlipid-based synthetic MD-2 antagonist using both animal model-based studies of pro-inflammatory cytokine responses and molecular modelling studies of a whole dendrimer with its target protein. Using this approach, it should now be possible to computationally design

Semiconducting Ba 3Sn 3Sb 4 and Metallic Ba 7–xSn 11Sb 15–y ( x = 0.4, y = 0.6) Zintl Phases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Haijie; Narayan, Awadhesh; Stoumpos, Constantinos C.

In this paper, we report the discovery of two ternary Zintl phases Ba 3Sn 3Sb 4 and Ba 7-xSn 11Sb 15-y, (x = 0.4, y = 0.6). Ba 3Sn 3Sb 4 adopts the monoclinic space group P2 1/c with a = 14.669(3) Å, b = 6.9649(14) Å, c = 13.629(3) Å, and β = 104.98(3)°. It features a unique corrugated two-dimensional (2D) structure consisting of [Sn 3Sb 4] 6- layers extending along the ab plane with Ba 2+ atoms sandwiched between them. The non-stoichiometric Ba 6.6Sn 11Sb 14.4 has a complex one-dimensional (1D) structure adopting the orthorhombic space group Pnma,more » with unit cell parameters a = 37.964(8) Å, b = 4.4090(9) Å and c = 24.682(5) Å. It consists of large double Sn-Sb ribbons separated by Ba 2+ atoms. Ba3Sn3Sb4 is an n-type semiconductor which has a narrow energy gap of ~0.18 eV and a room temperature carrier concentration of ~4.2 × 10 18 cm -3. Lastly, Ba 6.6Sn 11Sb 14.4 is determined to be a metal with electrons being the dominant carriers.« less

Semiconducting Ba 3Sn 3Sb 4 and Metallic Ba 7–xSn 11Sb 15–y ( x = 0.4, y = 0.6) Zintl Phases

DOE PAGES

Chen, Haijie; Narayan, Awadhesh; Stoumpos, Constantinos C.; ...

2017-11-08

In this paper, we report the discovery of two ternary Zintl phases Ba 3Sn 3Sb 4 and Ba 7-xSn 11Sb 15-y, (x = 0.4, y = 0.6). Ba 3Sn 3Sb 4 adopts the monoclinic space group P2 1/c with a = 14.669(3) Å, b = 6.9649(14) Å, c = 13.629(3) Å, and β = 104.98(3)°. It features a unique corrugated two-dimensional (2D) structure consisting of [Sn 3Sb 4] 6- layers extending along the ab plane with Ba 2+ atoms sandwiched between them. The non-stoichiometric Ba 6.6Sn 11Sb 14.4 has a complex one-dimensional (1D) structure adopting the orthorhombic space group Pnma,more » with unit cell parameters a = 37.964(8) Å, b = 4.4090(9) Å and c = 24.682(5) Å. It consists of large double Sn-Sb ribbons separated by Ba 2+ atoms. Ba3Sn3Sb4 is an n-type semiconductor which has a narrow energy gap of ~0.18 eV and a room temperature carrier concentration of ~4.2 × 10 18 cm -3. Lastly, Ba 6.6Sn 11Sb 14.4 is determined to be a metal with electrons being the dominant carriers.« less

Sub-Terrahertz Spectroscopy of E.COLI Dna: Experiment, Statistical Model, and MD Simulations

NASA Astrophysics Data System (ADS)

Sizov, I.; Dorofeeva, T.; Khromova, T.; Gelmont, B.; Globus, T.

2012-06-01

We will present result of combined experimental and computational study of sub-THz absorption spectra from Escherichia coli (E.coli) DNA. Measurements were conducted using a Bruker FTIR spectrometer with a liquid helium cooled bolometer and a recently developed frequency domain sensor operating at room temperature, with spectral resolution of 0.25 cm-1 and 0.03 cm-1, correspondingly. We have earlier demonstrated that molecular dynamics (MD) simulation can be effectively applied for characterizing relatively small biological molecules, such as transfer RNA or small protein thioredoxin from E. coli , and help to understand and predict their absorption spectra. Large size of DNA macromolecules ( 5 million base pairs for E. coli DNA) prevents, however, direct application of MD simulation at the current level of computational capabilities. Therefore, by applying a second order Markov chain approach and Monte-Carlo technique, we have developed a new statistical model to construct DNA sequences from biological cells. These short representative sequences (20-60 base pairs) are built upon the most frequently repeated fragments (2-10 base pairs) in the original DNA. Using this new approach, we constructed DNA sequences for several non-pathogenic strains of E.coli, including a well-known strain BL21, uro-pathogenic strain, CFT073, and deadly EDL933 strain (O157:H7), and used MD simulations to calculate vibrational absorption spectra of these strains. Significant differences are clearly present in spectra of strains in averaged spectra and in all components for particular orientations. The mechanism of interaction of THz radiation with a biological molecule is studied by analyzing dynamics of atoms and correlation of local vibrations in the modeled molecule. Simulated THz vibrational spectra of DNA are compared with experimental results. With the spectral resolution of 0.1 cm-1 or better, which is now available in experiments, the very easy discrimination between different

Synthesis and Characterization of an Earth-Abundant Cu2BaSn(S,Se)4 Chalcogenide for Photoelectrochemical Cell Application.

PubMed

Shin, Donghyeop; Ngaboyamahina, Edgard; Zhou, Yihao; Glass, Jeffrey T; Mitzi, David B

2016-11-17

Cu 2 BaSnS 4-x Se x films consisting of earth-abundant metals have been examined for photocathode application. Films with different Se contents (i.e., Cu 2 BaSnS 4-x Se x with x ≤ 2.4) were synthesized using a cosputter system with post-deposition sulfurization/selenization annealing treatments. Each film adopts a trigonal P3 1 crystal structure, with progressively larger lattice constants and with band gaps shifting from 2.0 to 1.6 eV, as more Se substitutes for S in the parent compound Cu 2 BaSnS 4 . Given the suitable bandgap and earth-abundant elements, the Cu 2 BaSnS 4-x Se x films were studied as prospective photocathodes for water splitting. Greater than 6 mA/cm 2 was obtained under illumination at -0.4 V versus reversible hydrogen electrode for Pt/Cu 2 BaSnS 4-x Se x films with ∼60% Se content (i.e., x = 2.4), whereas a bare Cu 2 BaSnS 4-x Se x (x = 2.4) film yielded ∼3 mA/cm 2 at -0.4 V/RHE.

Improvement of electron mobility in La:BaSnO{sub 3} thin films by insertion of an atomically flat insulating (Sr,Ba)SnO{sub 3} buffer layer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shiogai, Junichi, E-mail: junichi.shiogai@imr.tohoku.ac.jp; Nishihara, Kazuki; Sato, Kazuhisa

One perovskite oxide, ASnO{sub 3} (A = Sr, Ba), is a candidate for use as a transparent conductive oxide with high electron mobility in single crystalline form. However, the electron mobility of films grown on SrTiO{sub 3} substrates does not reach the bulk value, probably because of dislocation scattering that originates from the large lattice mismatch. This study investigates the effect of insertion of bilayer BaSnO{sub 3} / (Sr,Ba)SnO{sub 3} for buffering this large lattice mismatch between La:BaSnO{sub 3} and SrTiO{sub 3} substrate. The insertion of 200-nm-thick BaSnO{sub 3} on (Sr,Ba)SnO{sub 3} bilayer buffer structures reduces the number of dislocationsmore » and improves surface smoothness of the films after annealing as proved respectively by scanning transmission electron microscopy and atomic force microscopy. A systematic investigation of BaSnO{sub 3} buffer layer thickness dependence on Hall mobility of the electron transport in La:BaSnO{sub 3} shows that the highest obtained value of mobility is 78 cm{sup 2}V{sup −1}s{sup −1} because of its fewer dislocations. High electron mobility films based on perovskite BaSnO{sub 3} can provide a good platform for transparent-conducting-oxide electronic devices and for creation of fascinating perovskite heterostructures.« less

mdFoam+: Advanced molecular dynamics in OpenFOAM

NASA Astrophysics Data System (ADS)

Longshaw, S. M.; Borg, M. K.; Ramisetti, S. B.; Zhang, J.; Lockerby, D. A.; Emerson, D. R.; Reese, J. M.

2018-03-01

This paper introduces mdFoam+, which is an MPI parallelised molecular dynamics (MD) solver implemented entirely within the OpenFOAM software framework. It is open-source and released under the same GNU General Public License (GPL) as OpenFOAM. The source code is released as a publicly open software repository that includes detailed documentation and tutorial cases. Since mdFoam+ is designed entirely within the OpenFOAM C++ object-oriented framework, it inherits a number of key features. The code is designed for extensibility and flexibility, so it is aimed first and foremost as an MD research tool, in which new models and test cases can be developed and tested rapidly. Implementing mdFoam+ in OpenFOAM also enables easier development of hybrid methods that couple MD with continuum-based solvers. Setting up MD cases follows the standard OpenFOAM format, as mdFoam+ also relies upon the OpenFOAM dictionary-based directory structure. This ensures that useful pre- and post-processing capabilities provided by OpenFOAM remain available even though the fully Lagrangian nature of an MD simulation is not typical of most OpenFOAM applications. Results show that mdFoam+ compares well to another well-known MD code (e.g. LAMMPS) in terms of benchmark problems, although it also has additional functionality that does not exist in other open-source MD codes.

The Role of Annealing Process in Ag-Based BaSnO3 Multilayer Thin Films.

PubMed

Wu, Muying; Yu, Shihui; He, Lin; Yang, Lei; Zhang, Weifeng

2016-12-01

The BaSnO3/Ag/BaSnO3 multilayer structure was designed and fabricated on a quartz glass by magnetron sputtering, followed by an annealing process at a temperature from 150 to 750 °C in air. In this paper, we investigated the influence of the annealing temperature on the structural, optical, and electrical properties of the multilayers and proposed the mechanisms of conduction and transmittance. The maximum value of the figure of merit of 31.8 × 10(-3) Ω(-1) was achieved for the BaSnO3/Ag/BaSnO3 multilayer thin films annealed at 150 °C, while the average optical transmittance in the visible ranges was >84 %, the resistivity was 5.71 × 10(-5) Ω cm, and the sheet resistance was 5.57 Ω/sq. When annealed at below 600 °C, the values of resistivity and transmittance of the multilayers were within an acceptable range (resistivity <5.0 × 10(-4) Ω cm, transmittance >80 %). The observed property of the multilayer film is suitable for the application of transparent conductive electrodes.

MdHIR proteins repress anthocyanin accumulation by interacting with the MdJAZ2 protein to inhibit its degradation in apples

PubMed Central

Chen, Ke-Qin; Zhao, Xian-Yan; An, Xiu-Hong; Tian, Yi; Liu, Dan-Dan; You, Chun-Xiang; Hao, Yu-Jin

2017-01-01

In higher plants, jasmonate ZIM-domain (JAZ) proteins negatively regulate the biosynthesis of anthocyanins by interacting with bHLH transcription factors. However, it is largely unknown if and how other regulators are involved in this process. In this study, the apple MdJAZ2 protein was characterized in regards to its function in the negative regulation of anthocyanin accumulation and peel coloration. MdJAZ2 was used as a bait to screen a cDNA library using the yeast two-hybrid method. The hypersensitive induced reaction (HIR) proteins, MdHIR2 and MdHIR4, were obtained from this yeast two-hybrid. The ZIM domain of MdJAZ2 and the PHB domain of the MdHIR proteins are necessary for their interactions. The interactions were further verified using an in vitro pull-down assay. Subsequently, immunoblotting assays demonstrated that MdHIR4 enhanced the stability of the MdJAZ2-GUS protein. Finally, a viral vector-based transformation method showed that MdHIR4 inhibited anthocyanin accumulation and fruit coloration in apple by modulating the expression of genes associated with anthocyanin biosynthesis. PMID:28317851

Preparing MD-PhD students for clinical rotations: navigating the interface between PhD and MD training.

PubMed

Goldberg, Charles; Insel, Paul A

2013-06-01

Many aspects of MD-PhD training are not optimally designed to prepare students for their future roles as translational clinician-scientists. The transition between PhD research efforts and clinical rotations is one hurdle that must be overcome. MD-PhD students have deficits in clinical skills compared with those of their MD-only colleagues at the time of this transition. Reimmersion programs (RPs) targeted to MD-PhD students have the potential to help them navigate this transition.The authors draw on their experience creating and implementing an RP that incorporates multiple types of activities (clinical exam review, objective structured clinical examination, and supervised practice in patient care settings) designed to enhance the participants' skills and readiness for clinical efforts. On the basis of this experience, they note that MD-PhD students' time away from the clinical environment negatively affects their clinical skills, causing them to feel underprepared for clinical rotations. The authors argue that participation in an RP can help students feel more comfortable speaking with and examining patients and decrease their anxiety regarding clinical encounters. The authors propose that RPs can have positive outcomes for improving the transition from PhD to clinical MD training in dual-degree programs. Identifying and addressing this and other transitions need to be considered to improve the educational experience of MD-PhD students.

Registration of cotton germplasm USDA MD 16-1 and USDA MD 16-2 with enhanced lint yield and fiber quality.

USDA-ARS?s Scientific Manuscript database

Upland cotton germplasm USDA MD 16-1 (Reg. No. __ and PI ___ ), and USDA MD 16-2 (Reg. No. ___ and PI___) (Gossypium hirsutum L.), have enhanced yield and good fiber quality. These germplasm lines were developed by the USDA-ARS, Stoneville, MS and released in 2017. Two crosses, MD 25-51 X MD 10-9-1 ...

Magnetodielectric effect in (1 - x)(Ba0.88Ca0.12)(Ti0.88Zr0.12)O3 - xCoFe2O4

NASA Astrophysics Data System (ADS)

Pan, Pengfei; Tao, Jin; Ma, Fusheng; Zhang, Ning

2018-05-01

Magnetodielectric (MD) materials have attracted considerable attention due to their intriguing physics and potential future applications. In this work, polycrystalline (1 - x)(Ba0.88Ca0.12)(Ti0.88Zr0.12)O3 - xCoFe2O4 (x = 0.10, 0.20, 0.30, 0.40) ceramic have been prepared via sol-gel method. The room temperature magnetic and ferroelectric behaviors of the synthesized composites were investigated. For the composite with x = 0.40, a MD ratio of 5.37% was achieved under a magnetic field of 1.5 T at f = 1 kHz. The measured "butterfly hysteresis" MD curves exhibit an obvious dielectric anomaly. Theoretical analysis suggests that the observed magnetodielectric effect is attributed to the magnetoresistance effect and magnetoelectric coupling.

Thermoelectric transport properties of BaBiTe{sub 3}-based materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Yiming; Zhao, Li-Dong, E-mail: zhaolidong@buaa.edu.cn

BaBiTe{sub 3}, a material with low thermal conductivity, is an inferior thermoelectric material due to the poor electrical properties originated from its narrow band gap. We choose two types of dopants, K and La, trying to optimize its electrical transport properties. The minority carriers, which harm the Seebeck coefficient in this system, are suppressed by La doping. With the increase of both electrical conductivity and Seebeck coefficient, the power factor of 3% La doped BaBiTe{sub 3} reaches 3.7 μW cm{sup −1} K{sup −2} which increased by 40% from undoped BaBiTe{sub 3}. Besides high power factor, the thermal conductivity is alsomore » reduced in it. Eventually, a high ZT value, 0.25 at 473 K, for n-type BaBiTe{sub 3} is achieved in 3% La doped BaBiTe{sub 3}. - Graphical abstract: BaBiTe{sub 3} possesses a low thermal conductivity. However, it is an inferior thermoelectric material due to the poor electrical properties originated from its narrow band gap. A high ZT value of 0.25 at 473 K for n-type BaBiTe{sub 3} can be achieved through optimizing electrical transport properties via La doping. - Highlights: • BaBiTe{sub 3} is an analogue of these promising thermoelectric materials: such as CsBi{sub 4}Te{sub 6} and K{sub 2}Bi{sub 8}Se{sub 13}, etc. • BaBiTe{sub 3} possesses a low thermal conductivity. • La is an effective dopant to enhance electrical transport properties. • A high ZT value of 0.25 at 473 K can be achieved in n-type La-doped BaBiTe{sub 3}.« less

Large Energy Density, Excellent Thermal Stability, and High Cycling Endurance of Lead-Free BaZr0.2Ti0.8O3 Film Capacitors.

PubMed

Sun, Zixiong; Ma, Chunrui; Wang, Xi; Liu, Ming; Lu, Lu; Wu, Ming; Lou, Xiaojie; Wang, Hong; Jia, Chun-Lin

2017-05-24

A large energy storage density (ESD) of 30.4 J/cm 3 and high energy efficiency of 81.7% under an electrical field of 3 MV/cm was achieved at room temperature by the fabrication of environmentally friendly lead-free BaZr 0.2 Ti 0.8 O 3 epitaxial thin films on Nb-doped SrTiO 3 (001) substrates by using a radio-frequency magnetron sputtering system. Moreover, the BZT film capacitors exhibit great thermal stability of the ESD from 16.8 J/cm 3 to 14.0 J/cm 3 with efficiency of beyond 67.4% and high fatigue endurance (up to 10 6 cycles) in a wide temperature range from room temperature to 125 °C. Compared to other BaTiO 3 -based energy storage capacitor materials and even Pb-based systems, BaZr 0.2 Ti 0.8 O 3 thin film capacitors show either high ESD or great energy efficiency. All of these excellent results revealed that the BaZr 0.2 Ti 0.8 O 3 film capacitors have huge potential in the application of modern electronics, such as locomotive and pulse power, in harsh working environments.

33 CFR 334.180 - Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Naval Mine Warfare Test Station, or of U.S. Naval Air Station property. A person in the water or a... areas, U.S. Naval Air Test Center, Patuxent River, Md. 334.180 Section 334.180 Navigation and Navigable... REGULATIONS § 334.180 Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md...

33 CFR 334.180 - Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Naval Mine Warfare Test Station, or of U.S. Naval Air Station property. A person in the water or a... areas, U.S. Naval Air Test Center, Patuxent River, Md. 334.180 Section 334.180 Navigation and Navigable... REGULATIONS § 334.180 Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md...

33 CFR 334.180 - Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Naval Mine Warfare Test Station, or of U.S. Naval Air Station property. A person in the water or a... areas, U.S. Naval Air Test Center, Patuxent River, Md. 334.180 Section 334.180 Navigation and Navigable... REGULATIONS § 334.180 Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md...

33 CFR 334.180 - Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Naval Mine Warfare Test Station, or of U.S. Naval Air Station property. A person in the water or a... areas, U.S. Naval Air Test Center, Patuxent River, Md. 334.180 Section 334.180 Navigation and Navigable... REGULATIONS § 334.180 Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md...

33 CFR 334.180 - Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Naval Mine Warfare Test Station, or of U.S. Naval Air Station property. A person in the water or a... areas, U.S. Naval Air Test Center, Patuxent River, Md. 334.180 Section 334.180 Navigation and Navigable... REGULATIONS § 334.180 Patuxent River, Md.; restricted areas, U.S. Naval Air Test Center, Patuxent River, Md...

High mobility La-doped BaSnO3 on non-perovskite MgO substrate

NASA Astrophysics Data System (ADS)

Kim, Youjung; Shin, Juyeon; Kim, Young Mo; Char, Kookrin

(Ba,La)SnO3 is a transparent perovskite oxide with high electron mobility and excellent oxygen stability. Field effect device with (Ba,La)SnO3 channel was reported to show good output characteristics on STO substrate. Here, we fabricated (Ba,La)SnO3\\ films and field effect devices with (Ba,La)SnO3 channel on non-perovskite MgO substrates, which are available in large size wafers. X-ray diffraction and transmission electron microscope (TEM) images of (Ba,La)SnO3\\ films on MgO substrates show that the films are epitaxial with many threading dislocations. (Ba,La)SnO3 exhibits the high mobility with 97.2 cm2/Vs at 2 % La doping on top of 150 nm thick BaSnO3 buffer layer. Excellent carrier modulation was observed in field effect devices. FET performances on MgO substrates are slightly better than those on SrTiO3 substrates in spite of the higher dislocation density on MgO than on SrTiO3 substrates. These high mobility BaSnO3 thin films and transistors on MgO substrates will accelerate development for applications in high temperature and high power electronics. Samsung Science and Technology Foundation.

Registration of cotton germplasm line md 10-5

USDA-ARS?s Scientific Manuscript database

MD 10-5 (Reg. No. ______, PI 675077) is a noncommercial breeding line of cotton (Gossypium hirsutum L.) released by the USDA-ARS at Stoneville, MS in 2015. MD 10-5 was selected in F4 progenies from a cross between MD 15 (PI 642769) and JJ 1145ne. MD 10-5 has a desirable combination between lint yi...

Growth, improved thermal stability and spectral properties of Yb3+-ions doped high temperature phase α-Ba3Gd(BO3)3 crystals co-doped by Sr2+, Ca2+ and La3+ ions

NASA Astrophysics Data System (ADS)

Pan, Shangke; Zhang, Jianyu; Pan, Jianguo

2018-02-01

To investigate the cause of the thermal instability of Yb3+-ions doped Ba3Gd(BO3)3 crystal grown from Czochralski technique, the low temperature phase β-Ba3Gd(BO3)3 powder was synthesized at the temperature of 800 °C. To inhibit the phase transition of high temperature phase Yb:α-Ba3Gd(BO3)3 during the crystal growth process, co-doping ions Sr2+, Ca2+ and La3+ ions were introduced in Yb:α-Ba3Gd(BO3)3 crystal. The melting point increased and the thermal stability of Yb:α-Ba3Gd(BO3)3 crystal was improved by co-doping ions. The absorption peaks of co-doped crystals centered at 976 nm with FWHM of 11, 11 and 12 nm and the absorption cross sections were 3.40 × 10-21 cm2, 4.00 × 10-21 cm2 and 2.66 × 10-21 cm2, respectively. The emission cross sections at 1040 nm were 2.19 × 10-21 cm2, 2.53 × 10-21 cm2 and 1.93 × 10-21 cm2, respectively. The fluorescence times of co-doped by Sr2+, Ca2+ and La3+ ions were shorter than that of Yb:α-Ba3Gd(BO3)3 crystal. So Yb:α-Ba3Gd(BO3)3 crystals co-doped by Sr2+, Ca2+ and La3+ ions will be more suitable for LD-pumping laser.

Loss of BMI-1 dampens migration and EMT of colorectal cancer in inflammatory microenvironment through TLR4/MD-2/MyD88-mediated NF-κB signaling.

PubMed

Ye, Kai; Chen, Qi-Wei; Sun, Ya-Feng; Lin, Jian-An; Xu, Jian-Hua

2018-02-01

Increasing evidence from various clinical and experimental studies has demonstrated that the inflammatory microenvironment created by immune cells facilitates tumor migration. Epithelial-mesenchymal transition (EMT) is involved in the progression of cancer invasion and metastasis in an inflammatory microenvironment. B-lymphoma Moloney murine leukemia virus insertion region 1 (BMI-1) acts as an oncogene in various tumors. Ectopic expression of Bmi-1 have an effect on EMT and invasiveness. The purpose of this study was to investigate the efficacy of BMI-1 on inflammation-induced tumor migration and EMT and the underlying mechanism. We observed that the expression of BMI-1, TNF-α, and IL-1β was significantly increased in HT29 and HCT116 cells after THP-1 Conditioned-Medium (THP-1-CM) stimulation. Additionally, inhibition of BMI-1 impeded cell invasion induced by THP-1-CM-stimulation in both HT29 and HCT116 cells. BMI-1 knockdown remarkably repressed THP-1-CM-induced EMT by regulating the expression of EMT biomarkers with an increase in E-cadherin accompanied by decrease in N-cadherin and vimentin. Furthermore, downregulation of BMI-1 dramatically impeded THP-1-CM-triggered Toll-like receptor 4(TLR4)/myeloid differentiation protein 2(MD-2)/myeloid differentiation factor 88(MyD88) activity by repressing the expression of the TLR4/MD-2 complex and MyD88. Further data demonstrated that knockout of BMI-1 also dampened NF-κB THP-1-CM-triggered activity. Taken all data together, our findings established that BMI-1 modulated TLR4/MD-2/MyD88 complex-mediated NF-κB signaling involved in inflammation-induced cancer cells invasion and EMT, and therefore, could be a potential chemopreventive agent against inflammation-associated colorectal cancer. Establishment of an inflammatory microenvironment. Suppression of BMI-1 reverses THP-1-CM-induced inflammatory cytokine production in CRC. Loss of BMI-1 suppressed TLR4/MD-2/MyD88 complex-mediated NF-κB signaling. © 2017 Wiley

High-mobility BaSnO 3 grown by oxide molecular beam epitaxy

DOE PAGES

Raghavan, Santosh; Schumann, Timo; Kim, Honggyu; ...

2016-01-28

High-mobility perovskite BaSnO 3 films are of significant interest as newwide bandgap semiconductors for power electronics, transparent conductors, and as high mobility channels for epitaxial integration with functional perovskites. Despite promising results for single crystals, high-mobility BaSnO 3 films have been challenging to grow. Here, we demonstrate a modified oxide molecular beam epitaxy (MBE) approach, which supplies pre-oxidized SnO x. This technique addresses issues in the MBE of ternary stannates related to volatile SnO formation and enables growth of epitaxial, stoichiometric BaSnO 3. We demonstrate room temperature electron mobilities of 150 cm 2 V -1 s -1 in films grownmore » on PrScO 3. Lastly, the results open up a wide range of opportunities for future electronic devices.« less

Fe modified BaTiO{sub 3}: Influence of doping on ferroelectric property

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mishra, Ashutosh; Bisen, Supriya, E-mail: sbisen.sop@gmail.com; Jarabana, Kanaka Mahalakshmi

2015-06-24

We have investigate the ferroelectric property of Fe modified Barium Titanate (BaTiO{sub 3}) with possible tetragonal structure via solid state route was prepared. Modified sample of BaTi{sub 1−x}Fe{sub x}O{sub 3} (x=0.01, 0.02) were structural characterized by X-ray Diffraction (XRD) using a Bruker D8 Advance XRD instruments, the value of 2θ is in between 20° to 80°. Fourier transform infrared spectroscopy (FTIR) using a Bruker, vertex instruments has been performs to obtain Ti-O bonding in the modified sample; the region of wavenumber is from 4000 cm{sup −1} to 400 cm{sup −1}. P-E hysteresis loop measurements have been traced for different applied voltage- 100V,more » 300V and 500V.« less

Fe doped BaTiO3 sensitized by Fe3O4 nanoparticles for improved photoelectrochemical response

NASA Astrophysics Data System (ADS)

Upadhyay, Rishibrind Kumar; Sharma, Dipika

2018-01-01

Nanostructured powders of pristine Fe3O4, BaTiO3, and Fe-BaTiO3 were synthesized using hydrothermal method and BaTiO3/Fe3O4 and Fe-BaTiO3/Fe3O4 composite sample were also prepared by mixing the appropriate amount of pristine powders. All samples were characterized using x-ray diffraction, SEM and UV-vis spectrometry. Photoelectrochemical properties were investigated in a three-electrode cell system. Maximum photocurrent density of 2.1 mA cm-2 at 0.95 V/SCE was observed for Fe-BaTiO3/Fe3O4 composite sample. Increased photocurrent density offered by composite may be attributed to improved conductivity and better separation of the photogenerated charge carriers at interface.

Study of optical properties of BaMn1-xCrxO3 (x=0.0, 0.1, 0.2, 0.3, 0.4, 0.5) manganites using microwave synthesis method

NASA Astrophysics Data System (ADS)

Rani, Reena; Yadav, Kamlesh

2015-08-01

Barium manganite (BaMnO3), a perovskite based material, has been studied extensively. BaMnO3 properties can be changed by doping different elements at manganese (Mn) lattice site. We have prepared BaMnO3 and BaMn1-xCrxO3 (x=0.1, 0.2, 0.3, 0.4, 0.5) by Microwave Synthesizer. Data obtained from Fourier Transform Infrared Spectroscopy (FTIR) that the band gap of pure BaMnO3 is less as compare to the Cr doped BaMnO3. It is also clear from the FTIR that the band gap decreased with increasing the concentration of chromium. Broaden peak at 3201 cm-1 correspond to the stretching vibration of hydroxyl group (OH or H2O). The peaks appear on 724, 863 and 974 cm-1 is corresponding to the stretching vibration of metal oxide (M-O) bonds in the BaMnO3. BaMnO3 have applications in memory storage devices.

Observation of superconductivity in BaNb2S5

NASA Astrophysics Data System (ADS)

Smith, M. G.; Neumeier, J. J.

2018-06-01

Bulk superconductivity is reported in BaNb2S5 at the transition temperature Tc = 0.85(1) K. The electrical resistivity ρ versus T is metallic with ρ(2 K) = 42.4 μΩ cm. The magnetic susceptibility is paramagnetic, with temperature-independent contributions due to diamagnetism, Pauli paramagnetism, and Van Vleck paramagnetism; a Curie-Weiss contribution appears to be impurity related. Hall effect measurements show that the majority charge carriers are electrons with charge-carrier concentration n(3 K) = 2.40(2) × 1021 cm-3. Specific heat measurements reveal an electronic specific heat coefficient γ = 11.2(1) mJ/mol K2, a Debye temperature ΘD = 126.4(8) K, and an energy gap associated with the superconducting state of Eg = 0.184(4) meV. Measurements of ρ(T) in magnetic field provide the upper critical magnetic field of about 3055(74) Oe as T → 0 K, which was used to estimate the coherence length ξ = 6.21(15) nm. The results allow classification of BaNb2S5 as a Type II, BCS superconductor in the dirty limit.

Prediction of Osmotic Pressure of Ionic Liquids Inside a Nanoslit by MD Simulation and Continuum Approach

NASA Astrophysics Data System (ADS)

Moon, Gi Jong; Yang, Yu Dong; Oh, Jung Min; Kang, In Seok

2017-11-01

Osmotic pressure plays an important role in the processes of charging and discharging of lithium batteries. In this work, osmotic pressure of the ionic liquids confined inside a nanoslit is calculated by using both MD simulation and continuum approach. In the case of MD simulation, an ionic liquid is modeled as singly charged spheres with a short-ranged repulsive Lennard-Jones potential. The radii of the spheres are 0.5nm, reflecting the symmetry of ion sizes for simplicity. The simulation box size is 11nm×11nm×7.5nm with 1050 ion pairs. The concentration of ionic liquid is about 1.922mol/L, and the total charge on an individual wall varies from +/-60e(7.944 μm/cm2) to +/-600e(79.44 μm/cm2) . In the case of continuum approach, we classify the problems according to the correlation length and steric factor, and considered the four separate cases: 1) zero correlation length and zero steric factor, 2) zero correlation length and non-zero steric factor, 3) non-zero correlation length and zero steric factor, and 4) non-zero correlation and non-zero steric factor. Better understanding of the osmotic pressure of ionic liquids confined inside a nanoslit can be achieved by comparing the results of MD simulation and continuum approach. This research was supported by the National Research Foundation of Korea (NRF) Grant funded by the Korea government (MSIP: Ministry of Science, ICT & Future Planning) (No. 2017R1D1A1B05035211).

Apple fruit copper amine oxidase isoforms: peroxisomal MdAO1 prefers diamines as substrates, whereas extracellular MdAO2 exclusively utilizes monoamines.

PubMed

Zarei, Adel; Trobacher, Christopher P; Cooke, Alison R; Meyers, Ashley J; Hall, J Christopher; Shelp, Barry J

2015-01-01

4-Aminobutyrate (GABA) accumulates in apple fruit during controlled atmosphere storage. A potential source of GABA is the polyamine putrescine, which can be oxidized via copper-containing amine oxidase (CuAO), resulting in the production 4-aminobutanal/Δ(1)-pyrroline, with the consumption of O2 and release of H2O2 and ammonia. Five putative CuAO genes (MdAO genes) were cloned from apple (Malus domestica Borkh. cv. Empire) fruit, and the deduced amino acid sequences found to contain the active sites typically conserved in CuAOs. Genes encoding two of these enzymes, MdAO1 and MdAO2, were highly expressed in apple fruit and selected for further analysis. Amino acid sequence analysis predicted the presence of a C-terminal peroxisomal targeting signal 1 tripeptide in MdAO1 and an N-terminal signal peptide and N-glycosylation site in MdAO2. Transient expression of green fluorescent fusion proteins in Arabidopsis protoplasts or onion epidermal cells revealed a peroxisomal localization for MdAO1 and an extracellular localization for MdAO2. The enzymatic activities of purified recombinant MdAO1 and MdAO2 were measured continuously as H2O2 production using a coupled reaction. MdAO1 did not use monoamines or polyamines and displayed high catalytic efficiency for 1,3-diaminopropane, putrescine and cadaverine, whereas MdAO2 exclusively utilized aliphatic and aromatic monoamines, including 2-phenylethylamine and tyramine. Together, these results indicate that MdAO1 may contribute to GABA production via putrescine oxidation in the peroxisome of apple fruit under controlled atmosphere conditions. MdAO2 seems to be involved in deamination of 2-phenylethylamine, which is a step in the biosynthesis of 2-phenylethanol, a contributor to fruit flavor and flower fragrance. © The Author 2014. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Syntheses, crystal structure, and electronic properties of the five ABaMQ{sub 4} compounds RbBaPS{sub 4}, CsBaPS{sub 4}, CsBaVS{sub 4}, RbBaVSe{sub 4}, and CsBaVSe{sub 4}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mesbah, Adel; ICSM, UMR 5257 CEA / CNRS / UM / ENSCM, Site de Marcoule-Bâtiment 426, BP 17171, 30207 Bagnols-sur-Cèze Cedex; Prakash, Jai

Five new compounds belonging to the ABaMQ{sub 4} family were synthesized by solid-state chemistry at 1123 K. The compounds RbBaPS{sub 4}, CsBaPS{sub 4}, CsBaVS{sub 4}, RbBaVSe{sub 4}, and CsBaVSe{sub 4} are isostructural and have the TlEuPS{sub 4} structure type. They crystallize in space group D{sup 16}{sub 2h} – Pnma of the orthorhombic system. Their structure consists isolated MQ{sub 4} tetrahedra separated by A and Ba atoms to form a salt-like structure. Density Functional Theory (DFT) calculations of the electronic structures with the use of the HSE functional suggest that the compounds are semiconductors with calculated band gaps of 3.3 eVmore » (RbBaPS{sub 4}), 3.4 eV (CsBaPS{sub 4}), 2.3 eV (CsBaVS{sub 4}), and 1.6 eV (RbBaVSe{sub 4}). - Graphical abstract: General view of the ABaMQ{sub 4} structure down the a axis. - Highlights: • Five new ABaMQ{sub 4} compounds were synthesized by solid-state chemistry at 1123 K. • RbBaPS{sub 4}, CsBaPS{sub 4}, CsBaVS{sub 4}, RbBaVSe{sub 4}, and CsBaVSe{sub 4} have the TlEuPS{sub 4} structure type. • The compounds are semiconductors with calculated band gaps ranging from 1.6 to 3.4 eV.« less

Hot seeding for the growth of c-axis-oriented Nd-Ba-Cu-O

NASA Astrophysics Data System (ADS)

Chauhan, H. S.; Murakami, M.

2000-06-01

The fabrication of large single-grain RE-Ba-Cu-O (RE denotes rare earth elements) is essential for bulk applications. In the present study, we report on a hot-seeding method for growing Nd-Ba-Cu-O with Nd123 seed crystals. We made an arrangement, in which the Nd123 seed crystal can be transported to the centre of the furnace with a rod through a hole in a rubber cork and insulating stopper. The seed was placed in a small dip made in the rod, which can be turned to drop the seed on the sample. The advantage of this method is that perturbation in the growth conditions such as temperature and oxygen partial pressure can be minimized. Using this method we could grow large single-domain c-axis-oriented samples with the surface area larger than 3 cm×3 cm.

Investigation of structural, ferroelectric, piezoelectric and dielectric properties of Ba0.92Ca0.08TiO3-BaTi0.96Zr0.04O3 lead-free electroceramics

NASA Astrophysics Data System (ADS)

Keswani, Bhavna C.; Patil, S. I.; Kolekar, Y. D.

2018-04-01

Lead free ferroelectric with composition 0.55Ba0.92Ca0.08TiO3-0.45BaTi0.96Zr0.04O3 (BCT8-BZT4) was synthesized by solid state reaction method and investigated their structural, ferroelectric, piezoelectric and dielectric properties. X-ray diffraction analysis shows that BCT8-BZT4 ceramic possess both tetragonal (space group P4mm) and orthorhombic (space group Amm2) crystal structure which was further confirmed from Raman spectra spectroscopy. The micronized grains were observed from scanning electron micrographs while the presence of polarization-electric field hysteresis loop confirms ferroelectric nature of BCT8-BZT4 ceramic. Higher values of maximum polarization (Pmax = 22.27 μC/cm2), remnant polarization (Pr = 11.61 μC/cm2), coercive electric field (Ec = 4.77 kV/cm) and direct piezoelectric coefficient (d33) approximately 185 pC/N were observed. The real part of dielectric constant with frequency shows the usual dielectric dispersion behaviour at RT. The observed properties show that the lead free BCT8-BZT4 ceramic is suitable for ferroelectric memory device, piezoelectric sensor, capacitor, etc. applications.

ProtoMD: A prototyping toolkit for multiscale molecular dynamics

NASA Astrophysics Data System (ADS)

Somogyi, Endre; Mansour, Andrew Abi; Ortoleva, Peter J.

2016-05-01

ProtoMD is a toolkit that facilitates the development of algorithms for multiscale molecular dynamics (MD) simulations. It is designed for multiscale methods which capture the dynamic transfer of information across multiple spatial scales, such as the atomic to the mesoscopic scale, via coevolving microscopic and coarse-grained (CG) variables. ProtoMD can be also be used to calibrate parameters needed in traditional CG-MD methods. The toolkit integrates 'GROMACS wrapper' to initiate MD simulations, and 'MDAnalysis' to analyze and manipulate trajectory files. It facilitates experimentation with a spectrum of coarse-grained variables, prototyping rare events (such as chemical reactions), or simulating nanocharacterization experiments such as terahertz spectroscopy, AFM, nanopore, and time-of-flight mass spectroscopy. ProtoMD is written in python and is freely available under the GNU General Public License from github.com/CTCNano/proto_md.

Effect of the Cu/Ba ratio for the YBCO deposition onto IBAD template by the MOCVD method

NASA Astrophysics Data System (ADS)

Choi, J. K.; Kim, H. J.; Jun, B. H.; Kim, C. J.

2005-10-01

YBa2Cu3O7-x (YBCO) thin films were fabricated by the metal organic chemical vapor deposition (MOCVD) using a single liquid source. The copper/barium (Cu/Ba) ratio was varied from 1.26 to 1.38 to optimize the deposition condition. The IBAD template (CeO2/YSZ/stainless steel) was used as a substrate. The growth features of the YBCO films were not significantly influenced by the Cu/Ba ratio, while the superconducting transition temperature (Tc) and critical current (Ic) depended on the Cu/Ba ratio. When Cu/Ba ratio was between 1.26 and 1.29, Tc was as low as 80 K, while as Cu/Ba ratio increased to 1.38, it increased to above 85 K. The highest Tc (89.0 K) and Ic (46.3 A/cm-width) were achieved at the Cu/Ba ratio of 1.38 (Y:Ba:Cu = 1:2.1:2.9). It indicates that the optimum Cu/Ba ratio which differs from stoichiometric balance exists for the formation of the superconducting phase with a high Tc and Ic in MOCVD method.

Thermoelectric properties of sintered type-II clathrates (K, Ba)24(Ga, Sn)136 with various carrier concentrations

NASA Astrophysics Data System (ADS)

Kishimoto, Kengo; Koda, Shota; Akai, Koji; Koyanagi, Tsuyoshi

2015-09-01

We reported the thermoelectric properties of the sintered type-II clathrate K8Ba16Ga40Sn96 in a previous paper [S. Koda et al., J. Appl. Phys. 116, 023710 (2014)]. The clathrate had a high dimensionless figure of merit ZT, namely, 0.93. In this study, we optimized the carrier concentration n by modifying the chemical compositions of (K, Ba)24(Ga, Sn)136 samples, and heat treated the sintered samples. The carrier mobilities μ were improved because of the reduction in potential barrier scattering at grain boundaries. The room-temperature (RT) n values varied from 7.7 × 1017 to 3.7 × 1019 cm-3; the maximum RT μ value was 170 cm2V-1s-1. Consequently, we obtained a high ZT value of 1.19 at 630 K for n = 2.5 × 1019 cm-3. This material therefore has good thermoelectric properties.

Heteroepitaxial growth of Ba1 - xSrxTiO3/YBa2Cu3O7 - x by plasma-enhanced metalorganic chemical vapor deposition

NASA Astrophysics Data System (ADS)

Chern, C. S.; Liang, S.; Shi, Z. Q.; Yoon, S.; Safari, A.; Lu, P.; Kear, B. H.; Goodreau, B. H.; Marks, T. J.; Hou, S. Y.

1994-06-01

Epitaxial Ba1-xSrxTiO3(BST)/YBa2Cu3O7-x heterostructures with superior electrical and dielectric properties have been fabricated by plasma-enhanced metalorganic chemical vapor deposition (PE-MOCVD). Data of x-ray diffraction and high resolution transmission electron microscopy showed that <100> oriented Ba1-xSrxTiO3 layers were epitaxially deposited on epitaxial (001) YBa2Cu3O7-x layers. The leakage current density through the Ba1-xSrxTiO3 films was about 10-7 A/cm2 at 2 V (about 2×105 V/cm) operation. Moreover, the results of capacitance-temperature measurements showed that the PE-MOCVD Ba1-xSrxTiO3 films had Curie temperatures of about 30 °C and a peak dielectric constant of 600 at zero bias voltage. The Rutherford backscattering spectrometry and x-ray diffraction results showed that the BST film composition was controlled between Ba0.75Sr0.25TiO3 and Ba0.8Sr0.2TiO3. The structural and electrical properties of the Ba1-xSrxTiO3/YBa2Cu3O7-x heterostructure indicated that conductive oxide materials with close lattice to Ba1-xSrxTiO3 can be good candidates for the bottom electrode.

Annealing induced effect on the physical properties of ion-beam sputtered 0.5 Ba(Zr0.2Ti0.8)O3 - 0.5 (Ba0.7Ca0.3)TiO3-δ ferroelectric thin films

NASA Astrophysics Data System (ADS)

Oliveira, M. J. S.; Silva, J. P. B.; Veltruská, Kateřina; Matolín, V.; Sekhar, K. C.; Moreira, J. Agostinho; Pereira, M.; Gomes, M. J. M.

2018-06-01

This work reports thermal annealing induced effect on the structural, optical, chemical and ferroelectric properties of ion-beam sputtered lead-free ferroelectric 0.5 Ba(Zr0.2Ti0.8)O3 - 0.5 (Ba0.7Ca0.3)TiO3-δ (0.5BZT-0.5BCT) thin films. X-ray diffraction studies reveal that the tetragonality increases with the annealing temperature (Ta), while photoluminescence and X-ray photoelectron spectroscopy studies confirm that this effect is associated with the annihilation of the oxygen vacancies as well as changes in the Ba2+ coordination. The films annealed at 750 °C show a remarkable remnant polarization of Pr = 45.0 μC/cm2, with a coercive field of 32 kV/cm. The temperature dependence of the spontaneous polarization of the 0.5BZT-0.5BCT film reveals a mean field behavior of the polarization and the fatigue study reveals that Pr only decreases 3% after passing 109 cycles. Therefore the high remnant polarization and its high Pr stability make these films as promising candidates for memory applications.

Combining Rosetta with molecular dynamics (MD): A benchmark of the MD-based ensemble protein design.

PubMed

Ludwiczak, Jan; Jarmula, Adam; Dunin-Horkawicz, Stanislaw

2018-07-01

Computational protein design is a set of procedures for computing amino acid sequences that will fold into a specified structure. Rosetta Design, a commonly used software for protein design, allows for the effective identification of sequences compatible with a given backbone structure, while molecular dynamics (MD) simulations can thoroughly sample near-native conformations. We benchmarked a procedure in which Rosetta design is started on MD-derived structural ensembles and showed that such a combined approach generates 20-30% more diverse sequences than currently available methods with only a slight increase in computation time. Importantly, the increase in diversity is achieved without a loss in the quality of the designed sequences assessed by their resemblance to natural sequences. We demonstrate that the MD-based procedure is also applicable to de novo design tasks started from backbone structures without any sequence information. In addition, we implemented a protocol that can be used to assess the stability of designed models and to select the best candidates for experimental validation. In sum our results demonstrate that the MD ensemble-based flexible backbone design can be a viable method for protein design, especially for tasks that require a large pool of diverse sequences. Copyright © 2018 Elsevier Inc. All rights reserved.

UV - GAITHERSBURG MD

EPA Science Inventory

Brewer 105 is located in Gaithersburg MD, measuring ultraviolet solar radiation. Irradiance and column ozone are derived from this data. Ultraviolet solar radiation is measured with a Brewer Mark IV, single-monochrometer, spectrophotometer manufactured by SCI-TEC Instruments, Inc...

Celastrol reverses palmitic acid (PA)-caused TLR4-MD2 activation-dependent insulin resistance via disrupting MD2-related cellular binding to PA.

PubMed

Zhang, Xue; Wang, Ying; Ge, Hui-Ya; Gu, Yi-Jun; Cao, Fan-Fan; Yang, Chun-Xin; Uzan, Georges; Peng, Bin; Zhang, Deng-Hai

2018-04-18

Elevated plasma statured fatty acids (FFAs) cause TLR4/MD2 activation-dependent inflammation and insulin tolerance, which account for the occurrence and development of obesity. It has been confirmed that statured palmitic acid (PA) (the most abundant FFA) could bind MD2 to cause cellular inflammation. The natural compound celastrol could improve obesity, which is suggested via inhibiting inflammation, yet the detailed mechanism for celastrol is still unclear. As celastrol is reported to directly target MD2, we thought disrupting the binding between FFAs and MD2 might be one of the ways for celastrol to inhibit FFAs-caused inflammation and insulin resistance. In this study, we found evidence to support our hypothesis: celastrol could reverse PA-caused TLR4/MD2 activation-dependent insulin resistance, as determined by glucose-lowering ability, cellular glucose uptake, insulin action-related proteins and TLR4/MD2/NF-κB activation. Bioinformatics and cellular experiments showed that both celastrol and PA could bind MD2, and that celastrol could expel PA from cells. Finally, celastrol could reverse high fat diet caused hyperglycemia and obesity, and liver NF-kB activations. Taking together, we proved that celastrol could reverses PA-caused TLR4-MD2 activation-dependent insulin resistance via disrupting PA binding to MD2. © 2018 Wiley Periodicals, Inc.

Hydrothermal growth of highly textured BaTiO₃ films composed of nanowires.

PubMed

Zhou, Zhi; Lin, Yirong; Tang, Haixiong; Sodano, Henry A

2013-03-08

Textured barium titanate (BaTiO(3)) films are attracting immense research interest due to their lead-free composition and excellent piezoelectric and dielectric properties. Most synthesis methods for these films require a high temperature, leading to the formation of a secondary phase and an overall decrease in the electrical properties of the ceramic. In order to alleviate these issues, a novel fabrication method is introduced by transferring oriented rutile TiO(2) nanowires to a textured BaTiO(3) film at temperatures below 160 °C. The microstructure and thickness of the fabricated BaTiO(3) films were characterized by scanning electron microscopy, and the crystal structure and degree of orientation were evaluated by x-ray diffraction patterns using the Lotgering method. It is shown that the thickness of the BaTiO(3) film can be controlled by the length of TiO(2) nanowire array template, and the degree of orientation of the textured BaTiO(3) films is highly dependent on the film thickness; the crystallographic orientation has been measured to reach up to 87%. The relative dielectric constant (ε(r) = 1300) and ferroelectric properties (P(r) = 2.7 μC cm(-2), E(c) = 4.0 kV mm(-1)) of the textured BaTiO(3) films were also characterized to demonstrate their potential application in sensors, random access memory, and micro-electromechanical systems.

Tin doped PrBaFe 2O 5+δ anode material for solid oxide fuel cells

DOE PAGES

Dong, Guohui; Yang, Chunyang; He, Fei; ...

2017-04-25

Ceramic anodes have many advantages over cermet anodes for solid oxide fuel cells. We report the synthesis and characterization of Sn doped double perovskite PrBaFe (2-x)Sn xO 5+δ (x = 0–0.3) anode materials. Different crystal structures were observed depending on the Sn doping level and gas atmosphere. The materials demonstrated excellent stability in both reducing and redox atmospheres at elevated temperatures. The oxygen content in the as-prepared PrBaFe (2-x)Sn xO 5+δ was nonlinearly correlated to the Sn doping level and reached maximum values around x = 0.1. After the reducing treatment, the oxygen content linearly decreased with increasing Sn dopingmore » level. The electrical conductivity of bulk PrBaFe (2-x)Sn xO 5+δ (x = 0.1) reached 63.6 S cm -1 at 800 °C in humidified hydrogen. At 750 °C, the surface exchange coefficient and bulk diffusivity of PrBaFe (2-x)Sn xO 5+δ reached the maximum values of 4.42 × 10 -6 m s -1 and 6.04 × 10 -7 m 2 s -1, respectively, in the reducing process when the Sn doping level was x = 0.1. The activation energies of surface exchange coefficient and bulk diffusivity of PrBaFe (2-x)Sn xO 5+δ (x = 0.1) were 0.22 eV and 0.16 eV, respectively, in the reducing process. The area specific resistance of the PrBaFe (2-x)Sn xO 5+δ (x = 0.1) anode was 0.095–0.285 Ω cm 2 from 850–750 °C in humidified hydrogen, better than or comparable to the best ceramic anodes in the literature.« less

Lateral electric-field control of giant magnetoresistance in Co/Cu/Fe/BaTiO{sub 3} multiferroic heterostructure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Savitha Pillai, S.; Kojima, H.; Itoh, M.

2015-08-17

We report lateral electric-field-driven sizable changes in the magnetoresistance of Co/Cu/Fe tri-layered wires on BaTiO{sub 3} single crystal. While the observed change is marginal in the tetragonal phase of BaTiO{sub 3}, it reaches over 40% in the orthorhombic and rhombohedral phases with an electric field of 66 kV/cm. We attribute it to possible electric-field-induced variations of the spin-dependent electronic structures, i.e., spin polarization, of the Fe via interfacial strain transfer from BaTiO{sub 3}. The contrasting results for the different phases of BaTiO{sub 3} are discussed, associated with the distinct aspects of the ferroelectric polarization switching processes in each phase.

A high power diode-side-pumped Nd:YAG/BaWO4 Raman laser at 1103 nm

NASA Astrophysics Data System (ADS)

Li, Lei; Zhang, Xingyu; Liu, Zhaojun; Wang, Qingpu; Cong, Zhenhua; Zhang, Yuangeng; Wang, Weitao; Wu, Zhenguo; Zhang, Huaijin

2013-04-01

Pulsed operation at 1103 nm of a diode-side-pumped Nd:YAG laser with intracavity Raman shifting in BaWO4 is reported. The first Stokes wavelength at 1103 nm was generated by a Raman shift of 332 cm-1 from the fundamental wave (1064 nm). A maximum power at 1103 nm of 9.4 W was obtained for a diode pump power of 115 W at a pulse repetition rate of 15 kHz. The pump-to-Stokes conversion efficiency was up to 8.2%. When the output power at 1103 nm was over 7 W, a second Stokes line at 1145 nm was also observed in the experiment. Our research indicates that efficient Raman conversion can be realized by a Raman frequency shift at 332 cm-1 in BaWO4 Raman lasers.

Ba2Mg(BO3)2:Bi3+ - A new phosphor with ultraviolet light emission

NASA Astrophysics Data System (ADS)

Lakshminarasimhan, N.; Jayakiruba, S.; Prabhavathi, K.

2017-10-01

Ultraviolet light emission was observed in a new Ba2Mg(BO3)2:Bi3+ phosphor. Bi3+ substitution for Ba2+ in the lattice was supplemented with K+ to maintain the charge neutrality. The samples of the formula Ba2-2xBixKxMg(BO3)2 [x = 0, 0.001, 0.01, 0.02, and 0.05] synthesized by solid state reaction were characterized using powder X-ray diffraction for their phase formation. Raman and diffuse reflectance UV-Vis spectroscopic techniques were used to obtain information on the vibrational modes and optical properties, respectively. The room temperature photoluminescence measurements revealed an ultraviolet emission at 370 nm when excited using 304 nm wavelength and the Stokes shift is 5868 cm-1.

Raman and thermal-stability studies on annealed HgBa 2CuO 4+δ

NASA Astrophysics Data System (ADS)

Ren, Y. T.; Chang, H.; Xiong, Q.; Xue, Y. Y.; Chu, C. W.

1994-06-01

We have studied as-synthesized, vacuum-annealed and high-pressure oxygen annealed HgBa 2CuO 4+δ(Hg-1201) using Raman scattering. The apical-oxygen vibrational frequencies showed a slight but systematic shift (590, 591 and 587 cm -1), in agreement with the slight change in the Hg-O bond length from neutron-diffraction results. This suggested that the valence of Hg did not change significantly with oxygen content. The intensity of the ∼ 570 cm -1 peak decreased significantly after vacuum anneal and increased after high-pressure oxygen anneal, confirming the early assignment of this mode to interstitial oxygen. The thermal stability of these samples was studied by increasing laser power. High power density resulted in the decomposition of Hg-1201, mainly to BaCuO 2-δ, suggesting mercury loss upon local heating. It was found that the annealed samples decomposed more easily. In addition, one kind of crystallites exhibited a 326 cm -1 broad peak, which disappeared after high-power irradiation. We propose that this extra peak may come from HgO and/or the defect oxygen O (4).

Crystal Structure and Thermodynamic Stability of Ba/Ti-Substituted Pollucites for Radioactive Cs/Ba Immobilization

DOE PAGES

Xu, Hongwu; Chavez, Manuel E.; Mitchell, Jeremy N.; ...

2015-04-23

An analogue of the mineral pollucite (CsAlSi 2O 6), CsTiSi 2O 6.5 has a potential host phase for radioactive Cs. However, as 137Cs and 135Cs transmute to 137Ba and 135Ba, respectively, through the beta decay, it is essential to study the structure and stability of this phase upon Cs → Ba substitution. In this work, two series of Ba/Ti-substituted samples, Cs xBa (1-x)/2TiSi 2O 6.5 and Cs xBa 1-xTiSi 2O 7-0.5x, (x = 0.9 and 0.7), were synthesized by high-temperature crystallization from their respective precursors. Synchrotron X-ray diffraction and Rietveld analysis reveal that while Cs xBa (1-x)/2TiSi 2O 6.5 samplesmore » are phase-pure, Cs xBa 1-xTiSi 2O 7-0.5x samples contain Cs3x/(2+x)Ba (1-x)/(2+x)TiSi 2O 6.5 pollucites (i.e., also two-Cs-to-one-Ba substitution) and a secondary phase, fresnoite (Ba2TiSi2O8). Thus, the Cs xBa 1-xTiSi 2O 7-0.5x series is energetically less favorable than Cs xBa (1-x)/2TiSi 2O 6.5. To study the stability systematics of Cs xBa (1-x)/2TiSi 2O 6.5 pollucites, high-temperature calorimetric experiments were performed at 973 K with or without the lead borate solvent. Enthalpies of formation from the constituent oxides (and elements) have thus been derived. Our results show that with increasing Ba/(Cs + Ba) ratio, the thermodynamic stability of these phases decreases with respect to their component oxides. Hence, from the energetic viewpoint, continued Cs → Ba transmutation tends to destabilize the parent silicotitanate pollucite structure. However, the Ba-substituted pollucite co-forms with fresnoite (which incorporates the excess Ba), thereby providing viable ceramic waste forms for all the Ba decay products.« less

Large linear magnetoresistance in a new Dirac material BaMnBi2

NASA Astrophysics Data System (ADS)

Wang, Yi-Yan; Yu, Qiao-He; Xia, Tian-Long

2016-10-01

Dirac semimetal is a class of materials that host Dirac fermions as emergent quasi-particles. Dirac cone-type band structure can bring interesting properties such as quantum linear magnetoresistance and large mobility in the materials. In this paper, we report the synthesis of high quality single crystals of BaMnBi2 and investigate the transport properties of the samples. BaMnBi2 is a metal with an antiferromagnetic transition at T N = 288 K. The temperature dependence of magnetization displays different behavior from CaMnBi2 and SrMnBi2, which suggests the possible different magnetic structure of BaMnBi2. The Hall data reveals electron-type carriers and a mobility μ(5 K) = 1500 cm2/V·s. Angle-dependent magnetoresistance reveals the quasi-two-dimensional (2D) Fermi surface in BaMnBi2. A crossover from semiclassical MR ˜ H 2 dependence in low field to MR ˜ H dependence in high field, which is attributed to the quantum limit of Dirac fermions, has been observed in magnetoresistance. Our results indicate the existence of Dirac fermions in BaMnBi2. Project supported by the National Natural Science Foundation of China (Grant No. 11574391), the Fundamental Research Funds for the Central Universities, and the Research Funds of Renmin University of China (Grant No. 14XNLQ07).

High ferroelectric polarization in c-oriented BaTiO 3 epitaxial thin films on SrTiO 3/Si(001)

DOE PAGES

Scigaj, M.; Chao, C. H.; Gázquez, J.; ...

2016-09-21

The integration of epitaxial BaTiO 3 films on silicon, combining c-orientation, surface flatness, and high ferroelectric polarization is of main interest towards its use in memory devices. This combination of properties has been only achieved so far by using yttria-stabilized zirconia buffer layers. Here, the all-perovskite BaTiO 3/LaNiO 3/SrTiO 3 heterostructure is grown monolithically on Si(001). The BaTiO 3 films are epitaxial and c-oriented and present low surface roughness and high remnant ferroelectric polarization around 6 μC/cm 2. Lastly, this result paves the way towards the fabrication of lead-free BaTiO 3 ferroelectric memories on silicon platforms.

MdCOP1 Ubiquitin E3 Ligases Interact with MdMYB1 to Regulate Light-Induced Anthocyanin Biosynthesis and Red Fruit Coloration in Apple1[W][OA

PubMed Central

Li, Yuan-Yuan; Mao, Ke; Zhao, Cheng; Zhao, Xian-Yan; Zhang, Hua-Lei; Shu, Huai-Rui; Hao, Yu-Jin

2012-01-01

MdMYB1 is a crucial regulator of light-induced anthocyanin biosynthesis and fruit coloration in apple (Malus domestica). In this study, it was found that MdMYB1 protein accumulated in the light but degraded via a ubiquitin-dependent pathway in the dark. Subsequently, the MdCOP1-1 and MdCOP1-2 genes were isolated from apple fruit peel and were functionally characterized in the Arabidopsis (Arabidopsis thaliana) cop1-4 mutant. Yeast (Saccharomyces cerevisiae) two-hybrid, bimolecular fluorescence complementation, and coimmunoprecipitation assays showed that MdMYB1 interacts with the MdCOP1 proteins. Furthermore, in vitro and in vivo experiments indicated that MdCOP1s are necessary for the ubiquitination and degradation of MdMYB1 protein in the dark and are therefore involved in the light-controlled stability of the MdMYB1 protein. Finally, a viral vector-based transformation approach demonstrated that MdCOP1s negatively regulate the peel coloration of apple fruits by modulating the degradation of the MdMYB1 protein. Our findings provide new insight into the mechanism by which light controls anthocyanin accumulation and red fruit coloration in apple and even other plant species. PMID:22855936

Sulforaphane inhibits the engagement of LPS with TLR4/MD2 complex by preferential binding to Cys133 in MD2.

PubMed

Koo, Jung Eun; Park, Zee-Yong; Kim, Nam Doo; Lee, Joo Young

2013-05-10

Toll-like receptors (TLRs) are key pattern-recognition receptors that recognize invading pathogens and non-microbial endogenous molecules to induce innate and adaptive immune responses. Since activation of TLRs is deeply implicated in the pathological progress of autoimmune diseases, sepsis, metabolic diseases, and cancer, modulation of TLR activity is considered one of the most important therapeutic approaches. Lipopolysaccharide (LPS), an endotoxin of gram-negative bacteria, is a well-known agonist for TLR4 triggering inflammation and septic shock. LPS interacts with TLR4 through binding to a hydrophobic pocket in myeloid differentiation 2 (MD2), a co-receptor of TLR4. In this study, we showed that sulforaphane (SFN) interfered with the binding of LPS to MD2 as determined by in vitro binding assay and co-immunoprecipitation of MD2 and LPS in a cell system. The inhibitory effect of SFN on the interaction of LPS and MD2 was reversed by thiol supplementation with N-acetyl-L-cysteine or dithiothreitol showing that the inhibitory effect of SFN is dependent on its thiol-modifying activity. Indeed, micro LC-MS/MS analysis showed that SFN preferentially formed adducts with Cys133 in the hydrophobic pocket of MD2, but not with Cys95 and Cys105. Molecular modeling showed that SFN bound to Cys133 blocks the engagement of LPS and lipid IVa to hydrophobic pocket of MD2. Our results demonstrate that SFN interrupts LPS engagement to TLR4/MD2 complex by direct binding to Cys133 in MD2. Our data suggest a novel mechanism for the anti-inflammatory activity of SFN, and provide a novel target for the regulation of TLR4-mediated inflammatory and immune responses by phytochemicals. Copyright © 2013 Elsevier Inc. All rights reserved.

Optical spectroscopy of low-phonon Ho3+ doped BaY2F8 single crystal

NASA Astrophysics Data System (ADS)

Li, Chun; Zeng, Fanming; Lin, Hai; Zheng, Dongyang; Yang, Xiaodong; Liu, Wang; Liu, Jinghe

2014-12-01

The Ho:BaY2F8 crystal was grown by Czochralski method. The crystal phase structure and absorption spectra were tested, the absorption peak exists near 899 nm, the absorption cross section was 1.27 × 10-21 cm2. The emission spectra of crystals in the vicinity of 2 and 3.9 μm were measured, the 2 μm near infrared light induced by 5I7 → 5I8 transition of Ho3+ ions was observed, as well as the fluorescence output at 3.9 μm (5I5 → 5I6), emission cross section at 3.9 μm was calculated to be 0.86 × 10-21 cm2. We suppose that the Ho:BaY2F8 crystal has a large application prospect for the 2-4 μm wavelength near infrared laser.

Double-perovskites A 2FeMoO 6- δ (A = Ca, Sr, Ba) as anodes for solid oxide fuel cells

NASA Astrophysics Data System (ADS)

Zhang, Leilei; Zhou, Qingjun; He, Qiang; He, Tianmin

Double-perovskites A 2FeMoO 6- δ (A = Ca, Sr, Ba) have been investigated as potential anode materials for solid oxide fuel cells (SOFCs). At room temperature, A 2FeMoO 6- δ compounds crystallize in monoclinic, tetragonal, and cubic structures for A = Ca, Sr, and Ba, respectively. A weak peak observed at around 880 cm -1 in the Raman spectra can be attributed to traces of AMoO 4. XPS has confirmed the coexistence of Fe 2+-Mo 6+ and Fe 3+-Mo 5+ electronic configurations. Moreover, a systematic shift from Fe 2+/3+-Mo 6+/5+ to Fe 2+-Mo 6+ configuration is seen with increasing A-site cation size. A 2FeMoO 6- δ samples display distinct electrical properties in H 2, which can be attributed to different degrees of degeneracy of the Fe 2+-Mo 6+ and Fe 3+-Mo 5+ configurations. Ca 2FeMoO 6- δ is unstable in a nitrogen atmosphere, while Sr 2FeMoO 6- δ and Ba 2FeMoO 6- δ are stable up to 1200 °C. The thermal expansion coefficients of Sr 2FeMoO 6- δ and Ba 2FeMoO 6- δ are very close to that of La 0.9Sr 0.1Ga 0.8Mg 0.2O 3- δ (LSGM). The performances of cells with 300 μm thick LSGM electrolyte, double-perovskite SmBaCo 2O 5+ x cathodes, and A 2FeMoO 6- δ anodes follow the sequence Ca 2FeMoO 6- δ < Ba 2FeMoO 6- δ < Sr 2FeMoO 6- δ. The maximum power densities of a cell with an Sr 2FeMoO 6- δ anode reach 831 mW cm -2 in dry H 2 and 735 mW cm -2 in commercial city gas at 850 °C, respectively.

The Ba 4d-4f giant dipole resonance in complex Ba/Si compounds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sahle, Ch. J.; Sternemann, C.; Sternemann, H.

2014-08-06

The shape of the Ba 4d–4f giant dipole resonance is studied for Ba atoms embedded inside complex Si networks covering structures consisting of Si nanocages and nanotubes, i.e. the clathrate Ba 8Si 46, the complex compound BaSi 6, and the semiconducting BaSi 2. Here, non-resonant x-ray Raman scattering is used to investigate confinement effects on the shape of the giant resonance in the vicinity of the Ba NIV, V-edge. The distinct momentum transfer dependence of the spectra is analyzed and discussed. The measurements are compared to calculations of the giant resonance within time-dependent local density approximation in the dipole limit.more » No modulation of the giant resonance's shape for Ba atoms confined in different local environments was observed, in contrast to the calculations. The absence of such shape modulation for complex Ba/Si compounds is discussed providing important implications for further studies of giant resonance phenomena utilizing both theory and experiment.« less

The Ba 4d-4f giant dipole resonance in complex Ba/Si compounds

NASA Astrophysics Data System (ADS)

Sahle, Ch J.; Sternemann, C.; Sternemann, H.; Tse, J. S.; Gordon, R. A.; Desgreniers, S.; Maekawa, S.; Yamanaka, S.; Lehmkühler, F.; Wieland, D. C. F.; Mende, K.; Huotari, S.; Tolan, M.

2014-02-01

The shape of the Ba 4d-4f giant dipole resonance is studied for Ba atoms embedded inside complex Si networks covering structures consisting of Si nanocages and nanotubes, i.e. the clathrate Ba8Si46, the complex compound BaSi6, and the semiconducting BaSi2. Here, non-resonant x-ray Raman scattering is used to investigate confinement effects on the shape of the giant resonance in the vicinity of the Ba NIV, V-edge. The distinct momentum transfer dependence of the spectra is analyzed and discussed. The measurements are compared to calculations of the giant resonance within time-dependent local density approximation in the dipole limit. No modulation of the giant resonance’s shape for Ba atoms confined in different local environments was observed, in contrast to the calculations. The absence of such shape modulation for complex Ba/Si compounds is discussed providing important implications for further studies of giant resonance phenomena utilizing both theory and experiment.

LifeBridge new publication: Md.MD. Listing of 1,200 physicians a major part of consumer-type magazine.

PubMed

Botvin, Judith D

2004-01-01

LifeBridge Health, Baltimore, created a directory of its physicians, which developed into a 100-page consumer magazine titled Md.MD A Directory of the Region's Finest Physicians. Written and designed in-house, the premier edition paid for itself, thanks to publishing partner, Alter Communications. The premier edition was mailed to 50,000 Baltimore area homes last September.

Preparation of epitaxial TlBa2Ca2Cu3O9 high Tc thin films on LaAlO3 (100) substrates

NASA Astrophysics Data System (ADS)

Piehler, A.; Reschauer, N.; Spreitzer, U.; Ströbel, J. P.; Schönberger, R.; Renk, K. F.; Saemann-Ischenko, G.

1994-09-01

Epitaxial TlBa2Ca2Cu3O9 high Tc thin films were prepared on LaAlO3 (100) substrates by a combination of laser ablation and thermal evaporation of thallium oxide. X-ray diffraction patterns of θ-2θ scans showed that the films consisted of highly c axis oriented TlBa2Ca2Cu3O9. φ scan measurements revealed an epitaxial growth of the TlBa2Ca2Cu3O9 thin films on the LaAlO3 (100) substrates. Ac inductive measurements indicated the onset of superconductivity at 110 K. At 6 K, the critical current density was 4×106 A/cm2 in zero magnetic field and 6×105 A/cm2 at a magnetic field of 3 T parallel to the c axis.

33 CFR 110.72 - Blackhole Creek, Md.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Blackhole Creek, Md. 110.72 Section 110.72 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.72 Blackhole Creek, Md. The waters on the west side of...

33 CFR 110.72 - Blackhole Creek, Md.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Blackhole Creek, Md. 110.72 Section 110.72 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.72 Blackhole Creek, Md. The waters on the west side of...

Expression of MdCAS1 and MdCAS2, encoding apple beta-cyanoalanine synthase homologs, is concomitantly induced during ripening and implicates MdCASs in the possible role of the cyanide detoxification in Fuji apple (Malus domestica Borkh.) fruits.

PubMed

Han, Sang Eun; Seo, Young Sam; Kim, Daeil; Sung, Soon-Kee; Kim, Woo Taek

2007-08-01

Fruit ripening involves complex biochemical and physiological changes. Ethylene is an essential hormone for the ripening of climacteric fruits. In the process of ethylene biosynthesis, cyanide (HCN), an extremely toxic compound, is produced as a co-product. Thus, most cyanide produced during fruit ripening should be detoxified rapidly by fruit cells. In higher plants, the key enzyme involved in the detoxification of HCN is beta-cyanoalanine synthase (beta-CAS). As little is known about the molecular function of beta-CAS genes in climacteric fruits, we identified two homologous genes, MdCAS1 and MdCAS2, encoding Fuji apple beta-CAS homologs. The structural features of the predicted polypeptides as well as an in vitro enzyme activity assay with bacterially expressed recombinant proteins indicated that MdCAS1 and MdCAS2 may indeed function as beta-CAS isozymes in apple fruits. RNA gel-blot studies revealed that both MdCAS1 and MdCAS2 mRNAs were coordinately induced during the ripening process of apple fruits in an expression pattern comparable with that of ACC oxidase and ethylene production. The MdCAS genes were also activated effectively by exogenous ethylene treatment and mechanical wounding. Thus, it seems like that, in ripening apple fruits, expression of MdCAS1 and MdCAS2 genes is intimately correlated with a climacteric ethylene production and ACC oxidase activity. In addition, beta-CAS enzyme activity was also enhanced as the fruit ripened, although this increase was not as dramatic as the mRNA induction pattern. Overall, these results suggest that MdCAS may play a role in cyanide detoxification in ripening apple fruits.

BaZr 0.1Ce 0.7Y 0.1Yb 0.1O 3- δ electrolyte-based solid oxide fuel cells with cobalt-free PrBaFe 2O 5+ δ layered perovskite cathode

NASA Astrophysics Data System (ADS)

Ding, Hanping; Xue, Xingjian

A new anode-supported SOFC material system Ni-BZCYYb|BZCYYb|PBFO is investigated, in which a cobalt-free layered perovskite oxide, PrBaFe 2O 5+ δ (PBFO), is synthesized and employed as a novel cathode while the synthesized BZCYYb is used as an electrolyte. The cell is fabricated by a simple dry-pressing/co-sintering process. The cell is tested and characterized under intermediate temperature range from 600 to 700 °C with humified H 2 (∼3% H 2O) as fuel, ambient air as oxidant. The results show that the open-circuit potential of 1.006 V and maximal power density of 452 mW cm -2 are achieved at 700 °C. The polarization resistance of the electrodes is 0.18 Ω cm 2 at 700 °C. Compared to BaZr 0.1Ce 0.7Y 0.1O 3- δ, the conductivity of co-doped barium zirconate-cerate BZCYYb is significantly improved. The ohmic resistance of single cell is 0.37 Ω cm 2 at 700 °C. The results indicate that the developed Ni-BZCYYb|BZCYYb|PBFO cell is a promising functional material system for SOFCs.

Reconciling elemental Ba and barite as proxies of export production: Multiple Ba reservoirs in biogenic sediment

NASA Astrophysics Data System (ADS)

Murray, R. W.; Kryc, K. A.; Murray, D. W.

2003-12-01

The use of barite has long been recognized as a promising proxy for export production due to the relationship between its formation and settling biogenic matter. Accordingly, excess Ba (total Ba minus Ba associated with terrigenous material) calculations have been applied as a proxy of barite to assess export production, although this approach may be problematic. For example, because there are additional carrying phases of Ba in sediment other than terrigenous Ba and barite (e.g., oxides, organic matter), excess Ba may not be related in a predictable manner to export production. Indeed, previous workers have also identified the importance of non-barite reservoirs of Ba in sediment traps (e.g., Dymond et al., 1992; Francois et al., 1995) and sediment (e.g., Schroeder et al., 1997; Eagle et al., 2003). Despite these multiple reservoirs, the use of elemental Ba in biogenic sediment as a proxy of export production has a proven and resilient track record. To further understand the partitioning of Ba in biogenic sediment, we sequentially extracted seven, operationally-defined fractions (loosely-bound, exchangeable, carbonate, oxide, organic, opal, and residual) of sediment from surface and downcore samples from a cross-equatorial meridional transect in the equatorial Pacific. We find that Ba is evenly distributed between the sedimentary components with approximately 25-40 percent of the total extracted Ba in each of the exchangeable, carbonate, and oxide fractions for both surface and downcore sediment samples. In the surface sediment transect across the equator, there is no Ba in the residual fraction, and between 10 and 50 percent of the total extracted Ba is in the organic fraction. Also, downcore samples that were extracted from sediments with low relative bulk Ba/Ti tend to have Ba in both the residual and organic fractions as opposed to samples with high relative bulk Ba/Ti where there is a lack of Ba in both the residual and organic fractions. These observations

The AINTEGUMENTA genes, MdANT1 and MdANT2, are associated with the regulation of cell production during fruit growth in apple (Malus × domestica Borkh.).

PubMed

Dash, Madhumita; Malladi, Anish

2012-06-25

Fruit growth in apple (Malus × domestica Borkh.) is mediated by cell production and expansion. Genes involved in regulating these processes and thereby fruit growth, are not well characterized. We hypothesized that the apple homolog(s) of AINTEGUMENTA (ANT), an APETALA2-repeat containing transcription factor, regulates cell production during fruit growth in apple. Two ANT genes, MdANT1 and MdANT2, were isolated from apple and their expression was studied during multiple stages of fruit development. MdANT1 and MdANT2 expression was high during early fruit growth coincident with the period of cell production, rapidly declined during exit from cell production, and remained low during the rest of fruit development. The effects of increase in carbohydrate availability during fruit growth were characterized. Increase in carbohydrate availability enhanced fruit growth largely through an increase in cell production. Expression of MdANT1 and MdANT2 increased sharply by up to around 5-fold in response to an increase in carbohydrate availability. Expression of the ANT genes was compared across two apple genotypes, 'Gala' and 'Golden Delicious Smoothee' (GS), which differ in the extent of fruit growth, largely due to differences in cell production. In comparison to 'Gala', the larger fruit-size genotype, GS, displayed higher levels and a longer duration of MdANT1 and MdANT2 expression. Expression of the ANTs and cell cycle genes in the fruit core and cortex tissues isolated using laser capture microdissection was studied. During early fruit growth, expression of the MdANTs was higher within the cortex, the tissue that constitutes the majority of the fruit. Additionally, MdANT1 and MdANT2 expression was positively correlated with that of A- and B-type CYCLINS, B-type CYCLIN-DEPENDENT-KINASES (CDKBs) and MdDEL1. Multiple lines of evidence from this study suggest that MdANT1 and MdANT2 regulate cell production during fruit growth in apple. ANTs may coordinate the expression of

Vortex pinning in artificially layered Ba(Fe,Co)2As2 film

NASA Astrophysics Data System (ADS)

Oh, M. J.; Lee, Jongmin; Seo, Sehun; Yoon, Sejun; Seo, M. S.; Park, S. Y.; Kim, Ho-Sup; Ha, Dong-Woo; Lee, Sanghan; Jo, Youn Jung

2018-06-01

Static high critical current densities (Jc) > 1 MA/cm2 with magnetic field parallel or perpendicular to c-axis were realized in Co-doped/undoped multilayerd BaFe2As2 films. We made a current bridge by FIB to allow precise measurements, and confirmed that the boundary quality using FIB was considerably better than the quality achieved using a laser. The presence of a high in-plane Jc suggested the existence of c-axis correlated vortex pinning centers. To clarify the relationship between the Jc performance and superstructures, we investigated the magnetic flux pinning mechanism using scaling theory of the volume pinning force Fp(H). The Jc(H) curves, Fp/Fp,max vs. h = H/Hirr curves, and parameters p and q depended on the characteristics of the flux pinning mechanism. It was found that the dominant pinning mechanism of Co-doped/undoped multilayerd BaFe2As2 films was Δl-pinning and the inserted undoped BaFe2As2 layers remained non-superconducting. The dominant pin geometry varied when the magnetic field direction changed. It was concluded that the artificially layered BaFe2As2 film is a 3-D superconductor due to its long correlation length compared to the thickness of the non-superconducting layer.

Nonstoichiometric Solution-Processed BaTiO₃ Film for Gate Insulator Applications.

PubMed

Lau, Joyce; Kim, Sangsub; Kim, Hyunki; Koo, Kwangjun; Lee, Jaeseob; Kim, Sangsoo; Choi, Byoungdeog

2018-09-01

Solution processed barium titanate (BTO) was used to fabricate an Al/BaTiO3/p-Si metal-insulator-semiconductor (MIS) structure, which was used as a gate insulator. Changes in the electrical characteristics of the film were investigated as a function of the film thickness and post deposition annealing conditions. Our results showed that a thickness of 5 layers and an annealing temperature of 650 °C produced the highest electrical performance. BaxTi1-xO3 was altered at x = 0.10, 0.30, 0.50, 0.70, 0.90, and 1.0 to investigate changes in the electrical properties as a function of composition. The highest dielectric constant of 87 was obtained for x = 0.10, while the leakage current density was suppressed as Ba content increased. The lowest leakage current density was 1.34×10-10 A/cm2, which was observed at x = 0.90. The leakage current was related to the resistivity of the film, the interface states, and grain densification. Space charge limited current (SCLC) was the dominant leakage mechanism in BTO films based on leakage current analysis. Although a Ba content of x = 0.90 had the highest trap density, the traps were mainly composed of Ti-vacancies, which acted as strong electron traps and affected the film resistivity. A secondary phase, Ba2TiO4, which was observed in cases of excess Ba, acted as a grain refiner and provided faster densification of the film during the thermal process. The absence of a secondary phase in BaO (x = 1.0) led to the formation of many interface states and degradation in the electrical properties. Overall, the insulator properties of BTO were improved when the composition ratio was x = 0.90.

Microstructure and properties of single crystal BaTiO3 thin films synthesized by ion implantation-induced layer transfer

NASA Astrophysics Data System (ADS)

Park, Young-Bae; Ruglovsky, Jennifer L.; Atwater, Harry A.

2004-07-01

Single crystal BaTiO3 thin films have been transferred onto Pt-coated and Si3N4-coated substrates by the ion implantation-induced layer transfer method using H + and He+ ion coimplantation and subsequent annealing. The transferred BaTiO3 films are single crystalline with root mean square roughness of 17nm. Polarized optical and piezoresponse force microscopy (PFM) indicate that the BaTiO3 film domain structure closely resembles that of bulk tetragonal BaTiO3 and atomic force microscopy shows a 90° a -c domain structure with a tetragonal angle of 0.5°-0.6°. Micro-Raman spectroscopy indicates that the local mode intensity is degraded in implanted BaTiO3 but recovers during anneals above the Curie temperature. The piezoelectric coefficient, d33, is estimated from PFM to be 80-100pm/V and the coercive electric field (Ec) is 12-20kV/cm, comparable to those in single crystal BaTiO3.

CARNAÚBA: The Coherent X-Ray Nanoprobe Beamline for the Brazilian Synchrotron SIRIUS/LNLS

NASA Astrophysics Data System (ADS)

Tolentino, Hélio C. N.; Soares, Márcio M.; Perez, Carlos A.; Vicentin, Flávio C.; Abdala, Dalton B.; Galante, Douglas; Teixeira, Verônica de C.; de Araújo, Douglas H. C.; Westfahl, Harry, Jr.

2017-06-01

The CARNAÚBA beamline is the tender-to-hard X-ray (2 - 15 keV) scanning nanoprobe planned for the 4th generation storage ring SIRIUS at the LNLS. CARNAÚBA uses an undulator source with vertical linear polarization in a low-beta straight section and grazing incidence-focusing mirrors to create a nanoprobe at 143 m from the source. The beamline optic is based on KB mirrors and provides high brilliance at an achromatic focal spot down to the diffraction limit diameter of ˜30 nm with a working distance of ˜6 cm. These characteristics are crucial for studying nanometric samples in experiments involving complex stages and environments. The CARNAÚBA beamline aims to perform raster scans using x-ray fluorescence, x-ray absorption spectroscopy, x-ray diffraction and coherent x-ray imaging techniques. Computed tomography will extend these methods to three dimensions.

The AINTEGUMENTA genes, MdANT1 and MdANT2, are associated with the regulation of cell production during fruit growth in apple (Malus × domestica Borkh.)

PubMed Central

2012-01-01

Background Fruit growth in apple (Malus × domestica Borkh.) is mediated by cell production and expansion. Genes involved in regulating these processes and thereby fruit growth, are not well characterized. We hypothesized that the apple homolog(s) of AINTEGUMENTA (ANT), an APETALA2–repeat containing transcription factor, regulates cell production during fruit growth in apple. Results Two ANT genes, MdANT1 and MdANT2, were isolated from apple and their expression was studied during multiple stages of fruit development. MdANT1 and MdANT2 expression was high during early fruit growth coincident with the period of cell production, rapidly declined during exit from cell production, and remained low during the rest of fruit development. The effects of increase in carbohydrate availability during fruit growth were characterized. Increase in carbohydrate availability enhanced fruit growth largely through an increase in cell production. Expression of MdANT1 and MdANT2 increased sharply by up to around 5-fold in response to an increase in carbohydrate availability. Expression of the ANT genes was compared across two apple genotypes, ‘Gala’ and ‘Golden Delicious Smoothee’ (GS), which differ in the extent of fruit growth, largely due to differences in cell production. In comparison to ‘Gala’, the larger fruit-size genotype, GS, displayed higher levels and a longer duration of MdANT1 and MdANT2 expression. Expression of the ANTs and cell cycle genes in the fruit core and cortex tissues isolated using laser capture microdissection was studied. During early fruit growth, expression of the MdANTs was higher within the cortex, the tissue that constitutes the majority of the fruit. Additionally, MdANT1 and MdANT2 expression was positively correlated with that of A- and B-type CYCLINS, B-type CYCLIN-DEPENDENT-KINASES (CDKBs) and MdDEL1. Conclusions Multiple lines of evidence from this study suggest that MdANT1 and MdANT2 regulate cell production during fruit growth in

Remains of abutments for Bridge No. 1575 at MD Rt. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Remains of abutments for Bridge No. 1575 at MD Rt. 51 in Spring Gap, Maryland, looking northeast. (Compare with HAER MD-115 photos taken 1988). - Western Maryland Railway, Cumberland Extension, Pearre to North Branch, from WM milepost 125 to 160, Pearre, Washington County, MD

Apple MdACS6 Regulates Ethylene Biosynthesis During Fruit Development Involving Ethylene-Responsive Factor.

PubMed

Li, Tong; Tan, Dongmei; Liu, Zhi; Jiang, Zhongyu; Wei, Yun; Zhang, Lichao; Li, Xinyue; Yuan, Hui; Wang, Aide

2015-10-01

Ethylene biosynthesis in plants involves different 1-aminocyclopropane-1-carboxylic acid synthase (ACS) genes. The regulation of each ACS gene during fruit development is unclear. Here, we characterized another apple (Malus×domestica) ACS gene, MdACS6. The transcript of MdACS6 was observed not only in fruits but also in other tissues. During fruit development, MdACS6 was initiated at a much earlier stage, whereas MdACS3a and MdACS1 began to be expressed at 35 d before harvest and immediateley after harvest, respectively. Moreover, the enzyme activity of MdACS6 was significantly lower than that of MdACS3a and MdACS1, accounting for the low ethylene biosynthesis in young fruits. Overexpression of MdACS6 (MdACS6-OE) by transient assay in apple showed enhanced ethylene production, and MdACS3a was induced in MdACS6-OE fruits but not in control fruits. In MdACS6 apple fruits silenced by the virus-induced gene silencing (VIGS) system (MdACS6-AN), neither ethylene production nor MdACS3a transcript was detectable. In order to explore the mechanism through which MdACS3a was induced in MdACS6-OE fruits, we investigated the expression of apple ethylene-responsive factor (ERF) genes. The results showed that the expression of MdERF2 was induced in MdACS6-OE fruits and inhibited in MdACS6-AN fruits. Yeast one-hybrid assay showed that MdERF2 protein could bind to the promoter of MdACS3a. Moreover, down-regulation of MdERF2 in apple flesh callus led to a decrease of MdACS3a expression, demonstrating the regulation of MdERF2 on MdACS3a. The mechanism through which MdACS6 regulates the action of MdACS3a was discussed. © The Author 2015. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Study of the structure, dielectric and ferroelectric behavior of BaBi4+δTi4O15 ceramics

NASA Astrophysics Data System (ADS)

Khokhar, Anita; Goyal, Parveen K.; Thakur, O. P.; Sreenivas, K.

2016-05-01

The structure and ferroelectric properties of excess bismuth doped barium bismuth titanate BaBi4+δTi4O15 (δ = 2 - 10 wt.%)) ceramics prepared by solid-state reaction method have been investigated. X-ray diffraction (XRD) confirms the formation of a single phase material with a change in the orthorhombic distortion with varying excess of bismuth content. There is no change in the phase transition temperature (Tm) while the relaxor behaviour has been modified significantly with excess of bismuth doping. Saturated hysteresis loops with high remnant polarization (Pr ~ 12.5 µC/cm2), low coercive fields (Ec ~ 26 kV/cm) are measured and a high piezoelectric coefficient (d33 ~ 29 pC/N) is achieved in poled BaBi4Ti4O15 ceramics prepared with up to 8 wt.% of excess bismuth oxide. The improvement in the ferroelectric properties with increase in the excess bismuth content in BaBi4Ti4O15 ceramics has been explained in terms of changing oxygen vacancy concentration and structural relaxation. Tunable ferroelectric materials can be obtained by manipulating the doping amount of excess bismuth.

Temperature dependences of the electromechanical and electrocaloric properties of Ba(Zr,Ti)O3 and (Ba,Sr)TiO3 ceramics

NASA Astrophysics Data System (ADS)

Maiwa, Hiroshi

2017-10-01

The electrocaloric properties of Ba(Zr,Ti)O3 and (Ba,Sr)TiO3 ceramics (BZT and BST, respectively) were investigated by the indirect estimation and direct measurement of temperature-electric field (T-E) hysteresis loops. The measured T-E loops had shapes similar to those of the strain-electric field (s-E) loops. The measured temperature changes (ΔTs) at around 30 °C of the BZT ceramics sintered at 1450 °C and BST ceramics sintered at 1600 °C upon the release of the electric field from 30 kV/cm to 0 were 0.34 and 0.57 K, respectively. The temperature dependences of the electromechanical and electrocaloric properties were investigated. The BZT ceramics sintered at 1450 °C exhibited the largest electromechanical and electrocaloric properties at around 30 °C, which corresponds to the phase transition temperature. BST is more temperature dependent than BZT. BST ceramics sintered at 1600 °C exhibited the largest electromechanical and electrocaloric properties at around 29 °C, which is about 10 °C higher than the phase transition temperature.

High Performance Proton-Conducting Solid Oxide Fuel Cells with a Layered Perovskite GdBaCuCoO5+ x Cathode

NASA Astrophysics Data System (ADS)

Zhang, Xiaozhen; Jiang, Yuhua; Hu, Xuebing; Sun, Liangliang; Ling, Yihan

2018-03-01

Proton-conducting solid oxide fuel cell (H-SOFC) based on layered perovskite type GdBaCuCoO5+x (GBCC) cathode was fabricated with in situ drop-coating BaZr0.1Ce0.7Y0.2O3-δ (BZCY) electrolyte membrane. The influences of Cu doping into Co sites of GdBaCo2O5+ x on the electrical conductivity and conduction mechanism, thermal expansion property and electrochemical performance of cathode materials and corresponding single cell were investigated. Results show that the electrical conductivity decreased and the conduction mechanism would gradually transform to the semiconductor-like behavior. A high maximum power density of 480 mW cm-2 was obtained for the anode supported NiO-BZCY/NiO-BZCY/BZCY/GBCC single cells with wet H2 fuel at 700 °C. The corresponding polarization resistance was as low as 0.17 Ω cm2. The excellent electrochemical performance of as-prepared single cell indicates that GBCC is a good candidate of cathode materials for H-SOFCs.

76 FR 51424 - Satinder Dang, M.D.; Revocation of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-18

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 10-4] Satinder Dang, M.D... Control, Drug Enforcement Administration, issued an Order to Show Cause to Satinder K. Dang, M.D....'' Id. (citing Harrell E. Robinson, M.D., 74 FR 61370, 61376-77 (2010)). The ALJ also found that...

77 FR 67673 - Fernando Valle, M.D.; Decision and Order

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-13

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 12-56] Fernando Valle, M.D... Certificate of Registration Numbers FV1935595, FV2000711, and FV2000735, issued to Fernando Valle, M.D., be, and they hereby are, revoked. I further order that any pending applications of Fernando Valle, M.D...

78 FR 7813 - Sanjay Trivedi, M.D.; Decision and Order

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-04

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 12-57] Sanjay Trivedi, M.D....100(b), I order that DEA Certificate of Registration FT0896754, issued to Sanjay Trivedi, M.D., be, and it hereby is, revoked. I further order that any pending application of Sanjay Trivedi, M.D., to...

Growth of GaN single crystals by a Ca- and Ba-added Na flux method

NASA Astrophysics Data System (ADS)

Ukegawa, H.; Konishi, Y.; Fujimori, T.; Miyoshi, N.; Imade, M.; Yoshimura, M.; Kitaoka, Y.; Sasaki, T.; Mori, Y.

2011-02-01

GaN substrates are desirable for fabricating ultra-violet LEDs and LDs, and high-power and high-frequency transistors. High-quality GaN single crystals can be obtained by using Na flux method, but the growth habit of bulk crystals must be controlled. In this study, we investigated the effects of additives (Ca, Ba) on the growth habit and impurity concentration in the crystals. The aspect ratio (c/a) of the crystals was increased by increasing the amount of additives, showing that the growth habit could be changed from the pyramidal shape to the prism shape. Ba concentration was below the detection limit (1x1015 atoms/cm3).

Laser cooling of BaF

NASA Astrophysics Data System (ADS)

Bo, Yan; Bu, Wenhao; Chen, Tao; Lv, Guitao

2017-04-01

In this poster, we report our recently experimental progresses in laser cooling of BaF molecule. Our theoretic calculation shows BaF is a good candidate for laser cooling: quasi-cycling transitions, good wavelengths (around 900nm) for the main transitions. We have built a 4K cryogenic machine, laser ablate the target to make BaF molecules. The precise spectroscopy of BaF is measured and the laser cooling related transitions are identified. The collision between BaF and 4K He is carefully characterized. The quasi-cycling transition is demonstrated. And laser cooling experiment is going on.

Unusually high critical current of clean P-doped BaFe2As2 single crystalline thin film

NASA Astrophysics Data System (ADS)

Kurth, F.; Tarantini, C.; Grinenko, V.; Hänisch, J.; Jaroszynski, J.; Reich, E.; Mori, Y.; Sakagami, A.; Kawaguchi, T.; Engelmann, J.; Schultz, L.; Holzapfel, B.; Ikuta, H.; Hühne, R.; Iida, K.

2015-02-01

Microstructurally clean, isovalently P-doped BaFe2As2 (Ba-122) single crystalline thin films have been prepared on MgO (001) substrates by molecular beam epitaxy. These films show a superconducting transition temperature (Tc) of over 30 K although P content is around 0.22, which is lower than the optimal one for single crystals (i.e., 0.33). The enhanced Tc at this doping level is attributed to the in-plane tensile strain. The strained film shows high transport self-field critical current densities (Jc) of over 6 MA/cm2 at 4.2 K, which are among the highest for Fe based superconductors (FeSCs). In-field Jc exceeds 0.1 MA/cm2 at μ 0 H = 35 T for H ‖ a b and μ 0 H = 18 T for H ‖ c at 4.2 K, respectively, in spite of moderate upper critical fields compared to other FeSCs with similar Tc. Structural investigations reveal no defects or misoriented grains pointing to strong pinning centers. We relate this unexpected high Jc to a strong enhancement of the vortex core energy at optimal Tc, driven by in-plane strain and doping. These unusually high Jc make P-doped Ba-122 very favorable for high-field magnet applications.

Ca, Sr and Ba stable isotopes reveal the fate of soil nutrients along a tropical climosequence

USGS Publications Warehouse

Bullen, Thomas D.; Chadwick, Oliver A.

2016-01-01

Nutrient biolifting is an important pedogenic process in which plant roots obtain inorganic nutrients such as phosphorus (P) and calcium (Ca) from minerals at depth and concentrate those nutrients at the surface. Here we use soil chemistry and stable isotopes of the alkaline earth elements Ca, strontium (Sr) and barium (Ba) to test the hypothesis that biolifting of P has been an important pedogenic process across a soil climosequence developed on volcanic deposits at Kohala Mountain, Hawaii. The geochemical linkage between these elements is revealed as generally positive site-specific relationships in soil mass gains and losses, particularly for P, Ba and Ca, using the ratio of immobile elements titanium and niobium (Ti/Nb) to link individual soil samples to a restricted compositional range of the chemically and isotopically diverse volcanic parent materials. At sites where P is enriched in surface soils relative to abundances in deeper soils, the isotope compositions of exchangeable Ca, Sr and Ba in the shallowest soil horizons (< 10 cm depth) are lighter than those of the volcanic parent materials and trend toward those of plants growing on fresh volcanic deposits. In contrast the isotope composition of exchangeable Ba in deeper soil horizons (> 10 cm depth) at those sites is consistently heavier than the volcanic parent materials. The isotope compositions of exchangeable Ca and Sr trend toward heavier compositions with depth more gradually, reflecting increasing leakiness from these soils in the order Ba < Sr < Ca and downward transfer of light biocycled Ca and Sr to deeper exchange sites. Given the long-term stability of ecosystem properties at the sites where P is enriched in surface soils, a simple box model demonstrates that persistence of isotopically light exchangeable Ca, Sr and Ba in the shallowest soil horizons requires that the uptake flux to plants from those near-surface layers is less than the recycling flux returned to the surface as

Ultrasound-assisted synthesis of poly(MMA-co-BA)/ZnO nanocomposites with enhanced physical properties.

PubMed

Poddar, Maneesh Kumar; Sharma, Sachin; Pattipaka, Srinivas; Pamu, D; Moholkar, Vijayanand S

2017-11-01

The present study reports synthesis and characterization of poly(MMA-co-BA)/ZnO nanocomposites using ultrasound-assisted in-situ emulsion polymerization. Methyl methacrylate (MMA) was copolymerized with butyl acrylate (BA), for enhanced ductility of copolymer matrix, in presence of nanoscale ZnO particles. Ultrasound generated strong micro-turbulence in reaction mixture, which resulted in higher encapsulation and uniform dispersion of ZnO (in native form - without surface modification) in polymer matrix, as compared to mechanical stirring. The nanocomposites were characterized for physical properties and structural morphology using standard techniques such as XRD, FTIR, particle size analysis, UV-Visible spectroscopy, electrical conductivity, TGA, DSC, FE-SEM and TEM. Copolymerization of MMA and BA (in presence of ZnO) followed second order kinetics. Thermal stability (T 10% =324.9°C) and glass transition temperature (T g =67.8°C) of poly(MMA-co-BA)/ZnO nanocomposites showed significant enhancement (35.1°C for 1wt% ZnO and 15.7°C for 4wt% ZnO, respectively), as compared to pristine poly(MMA-co-BA). poly(MMA-co-BA)/ZnO (5wt%) nanocomposites possessed the highest electrical conductivity of 0.192μS/cm and peak UV absorptivity of 0.55 at 372nm. Solution rheological study of nanocomposites revealed enhancement in viscosity with increasing ZnO loading. Maximum viscosity of 0.01Pa-s was obtained for 5wt% ZnO loading. Copyright © 2017 Elsevier B.V. All rights reserved.

75 FR 80744 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-9-81 (MD-81), DC-9-82 (MD-82...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-23

...: We propose to adopt a new airworthiness directive (AD) for all Model DC-9-81 (MD-81), DC-9-82 (MD-82... inspections for cracking of the left and right upper center skin panels of the horizontal stabilizer, and..., West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590. Hand...

Assessing the allelotypic effect of two aminocyclopropane carboxylic acid synthase-encoding genes MdACS1 and MdACS3a on fruit ethylene production and softening in Malus

PubMed Central

Dougherty, Laura; Zhu, Yuandi; Xu, Kenong

2016-01-01

Phytohormone ethylene largely determines apple fruit shelf life and storability. Previous studies demonstrated that MdACS1 and MdACS3a, which encode 1-aminocyclopropane-1-carboxylic acid synthases (ACS), are crucial in apple fruit ethylene production. MdACS1 is well-known to be intimately involved in the climacteric ethylene burst in fruit ripening, while MdACS3a has been regarded a main regulator for ethylene production transition from system 1 (during fruit development) to system 2 (during fruit ripening). However, MdACS3a was also shown to have limited roles in initiating the ripening process lately. To better assess their roles, fruit ethylene production and softening were evaluated at five time points during a 20-day post-harvest period in 97 Malus accessions and in 34 progeny from 2 controlled crosses. Allelotyping was accomplished using an existing marker (ACS1) for MdACS1 and two markers (CAPS866 and CAPS870) developed here to specifically detect the two null alleles (ACS3a-G289V and Mdacs3a) of MdACS3a. In total, 952 Malus accessions were allelotyped with the three markers. The major findings included: The effect of MdACS1 was significant on fruit ethylene production and softening while that of MdACS3a was less detectable; allele MdACS1–2 was significantly associated with low ethylene and slow softening; under the same background of the MdACS1 allelotypes, null allele Mdacs3a (not ACS3a-G289V) could confer a significant delay of ethylene peak; alleles MdACS1–2 and Mdacs3a (excluding ACS3a-G289V) were highly enriched in M. domestica and M. hybrid when compared with those in M. sieversii. These findings are of practical implications in developing apples of low and delayed ethylene profiles by utilizing the beneficial alleles MdACS1-2 and Mdacs3a. PMID:27231553

Swiss national MD-PhD-program: an outcome analysis.

PubMed

Kuehnle, Katrin; Winkler, David T; Meier-Abt, Peter J

2009-09-19

This study aims at a first evaluation of the outcome of the Swiss national MD-PhD program during the last 16 years. One hundred and twenty six former and current students in the Swiss national MD-PhD program were surveyed via a Web-based questionnaire in September 2007. Twenty-four questions assessed information regarding participant demographics, information on the PhD thesis and publication activity, current positions and research activity, as well as participant's opinions, attitudes and career goals. Eighty questionnaires were received from 126 MD-PhD students and graduates (63.5% response rate). The responders consisted of present students (36%), former graduates (56%), and dropouts (8%). The percentage of women in the program was 23%, and the average duration of the program was 4.2 +/- 1.4 years. Research interests were predominantly in the fields of neuroscience, immunology, molecular biology and cancer research. A considerable portion of the MD-PhD graduates had an excellent publication record stemming from their PhD research work, and 89% were planning to continue a research-orientated career. Over 50% of those MD-PhD graduates completing their thesis before 2002 had already reached an assistant or full professor position at the time of the survey. Nearly all participants considered the MD-PhD training helpful to their career and high quality standards were assigned to the acquired practical and intellectual skills. However, criticism was expressed concerning the general mentoring and the career related mentoring. Moreover, general mentoring and career related mentoring were significantly less well perceived in research groups employing more than seven PhD students at the same time. The MD-PhD students and graduates surveyed were satisfied with their education and most of them continued a research-orientated career. Regarding the overall positive evaluation, this study supports the view that MD-PhD graduates are well qualified for a successful career in

VizieR Online Data Catalog: Ba V, Ba VI, and Ba VII oscillator strengths (Rauch+, 2014)

NASA Astrophysics Data System (ADS)

Rauch, T.; Werner, K.; Quinet, P.; Kruk, J. W.

2014-04-01

table1.dat contains calculated HFR oscillator strengths (loggf) and transition probabilities (gA, in 1/s) in Ba V. CF is the cancellation factor as defined by Cowan (1981). In columns 3 and 6, e is written for even and o for odd. table2.dat contains calculated HFR oscillator strengths (loggf) and transition probabilities (gA, in 1/s) in Ba VI. CF is the cancellation factor as defined by Cowan (1981). In columns 3 and 6, e is written for even and o for odd. table3.dat contains calculated HFR oscillator strengths (loggf) and transition probabilities (gA, in 1/s) in Ba VII. CF is the cancellation factor as defined by Cowan (1981). In columns 3 and 6, e is written for even and o for odd. (3 data files).

Critical current density of TlBa 2Ca 2Cu 3O 9 thin films on MgO (100) in magnetic fields

NASA Astrophysics Data System (ADS)

Piehler, A.; Ströbel, J. P.; Reschauer, N.; Löw, R.; Schönberger, R.; Renk, K. F.; Kraus, M.; Daniel, J.; Saemann-Ischenko, G.

1994-04-01

We report on the critical current density of TlBa 2Ca 2Cu 3O 9 thin films on (100) MgO substrates in magnetic fields. Single- phase and highly c-axis oriented thin films were prepared by laser ablation in combination with thermal evaporation of Tl 2O 3. Scanning electron microscope investigations indicated a flat plate-like microstructure and DC magnetization measurements showed the onset of superconductivity at ∼ 115 K. The critical current density jc was determined from magnetization cycles. Typical values of jc were 9 × 10 5 A/cm 2 at 6 K and 2.5 × 10 5 A/cm 2 at 77 K. In a magnetic field to 1 T applied parallel to the c-axis the critical current densities were 3 × 10 5 A/cm 2 at 6 K and 3 × 10 3 A/cm 2 at 77 K. The decrease of jc at higher magnetic fields is discussed and attributed to the microstructure of the TlBa 2Ca 2Cu 3O 9 thin films.

MD-11 PCA - Research flight team photo

NASA Technical Reports Server (NTRS)

1995-01-01

On Aug. 30, 1995, a the McDonnell Douglas MD-11 transport aircraft landed equipped with a computer-assisted engine control system that has the potential to increase flight safety. In landings at NASA Dryden Flight Research Center, Edwards, California, on August 29 and 30, the aircraft demonstrated software used in the aircraft's flight control computer that essentially landed the MD-11 without a need for the pilot to manipulate the flight controls significantly. In partnership with McDonnell Douglas Aerospace (MDA), with Pratt & Whitney and Honeywell helping to design the software, NASA developed this propulsion-controlled aircraft (PCA) system following a series of incidents in which hydraulic failures resulted in the loss of flight controls. This new system enables a pilot to operate and land the aircraft safely when its normal, hydraulically-activated control surfaces are disabled. This August 29, 1995, photo shows the MD-11 team. Back row, left to right: Tim Dingen, MDA pilot; John Miller, MD-11 Chief pilot (MDA); Wayne Anselmo, MD-11 Flight Test Engineer (MDA); Gordon Fullerton, PCA Project pilot; Bill Burcham, PCA Chief Engineer; Rudey Duran, PCA Controls Engineer (MDA); John Feather, PCA Controls Engineer (MDA); Daryl Townsend, Crew Chief; Henry Hernandez, aircraft mechanic; Bob Baron, PCA Project Manager; Don Hermann, aircraft mechanic; Jerry Cousins, aircraft mechanic; Eric Petersen, PCA Manager (Honeywell); Trindel Maine, PCA Data Engineer; Jeff Kahler, PCA Software Engineer (Honeywell); Steve Goldthorpe, PCA Controls Engineer (MDA). Front row, left to right: Teresa Hass, Senior Project Management Analyst; Hollie Allingham (Aguilera), Senior Project Management Analyst; Taher Zeglum, PCA Data Engineer (MDA); Drew Pappas, PCA Project Manager (MDA); John Burken, PCA Control Engineer.

75 FR 31835 - Environmental Impact Statement: Calvert and St. Mary's Counties, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-04

...: Calvert and St. Mary's Counties, MD AGENCY: Federal Highway Administration (FHWA), DOT. ACTION: Notice of... project in Calvert and St. Mary's Counties, Maryland (Federal Register Vol. 72, No. 203; FR Doc. 07-5190... replacement of MD 4 from MD 2 to MD 235 in Calvert and St. Mary's Counties, a distance of approximately 4.1...

A novel gene, MdSSK1, as a component of the SCF complex rather than MdSBP1 can mediate the ubiquitination of S-RNase in apple.

PubMed

Yuan, Hui; Meng, Dong; Gu, Zhaoyu; Li, Wei; Wang, Aide; Yang, Qing; Zhu, Yuandi; Li, Tianzhong

2014-07-01

As a core factor in S-RNase-based gametophytic self-incompatibility (GSI), the SCF (SKP1-Cullin1-F-box-Rbx1) complex (including pollen determinant SLF, S-locus-F-box) functions as an E3 ubiquitin ligase on non-self S-RNase. The SCF complex is formed by SKP1 bridging between SLF, CUL1, and Rbx1; however, it is not known whether an SCF complex lacking SKP1 can mediate the ubiquitination of S-RNase. Three SKP1-like genes from pollen were cloned based on the structural features of the SLF-interacting-SKP1-like (SSK) gene and the 'Golden Delicious' apple genome. These genes have a motif of five amino acids following the standard 'WAFE' at the C terminal and, in addition, contain eight sheets and two helices. All three genes were expressed exclusively in pollen. In the yeast two-hybrid and pull-down assays only one was found to interact with MdSFBB and MdCUL1, suggesting it is the SLF-interacting SKP1-like gene in apple which was named MdSSK1. In vitro experiments using MdSSK1, S2-MdSFBB1 (S2-Malus domestica S-locus-F-box brother) and MdCUL1 proteins incubated with S 2-RNase and ubiquitin revealed that the SCF complex ubiquitinylates S-RNase in vitro, while MdSBP1 (Malus domestica S-RNase binding protein 1) could not functionally replace MdSSK1 in the SCF complex in ubiquitinylating S-RNase. According to the above experiments, MdSBP1 is probably the only factor responsible for recognition with S-RNase, while not a component of the SCF complex, and an SCF complex containing MdSSK1 is required for mediating the ubiquitination of S-RNase. © The Author 2014. Published by Oxford University Press on behalf of the Society for Experimental Biology.

Augmentation de la densité de courant critique par dopage de YBCO texturé au BaSnO3

NASA Astrophysics Data System (ADS)

Lepropre, M.; Monot, I.; Delamare, M. P.; Hervieu, M.; Simon, Ch.; Provost, J.; Desgardin, G.; Raveau, B.

1994-11-01

We have performed critical current density measurements (DC current) on melt textured YBaCuO doped with BaSnO3 which exhibits transport values at 77 K as high as 7.1 × 10^4 A cm^{-2} in zero field and 1.1 × 10^4 A cm^{-2} at 20 T. A systematic study of this ceramic has been carried out using SEM and HREM observations in correlation with J_c measurements. A textured microstructure is observed containing numerous green phase inclusions (size leq 10 μm) as well as a few numbers of BaSnO3 inclusions (size < 1 μm). It has been found that transport J_c data are distributed over a wide range (2.5 × 10^3-7.1 × 10^4 A cm^{-2}). Nevertheless, magnetic J_c measurements suggest that cracks of the order of several microns may appear in some regions of the material leading to a dramatic decrease of transport J_c for the corresponding sample. On the other hand, HREM observations demonstrate that extended defects cannot be considered as the major factor for vortex pinning in textured 123 material. The presence or the absence of inhomogeneity at the nanoscale does not seem to influence the critical current density. Finally, it has been determined that pinning can be ascribed to lamellar microstructure rather than to BaSnO3 inclusions. Nous avons mesuré la densité de courant critique de transport (courant continu) J_c, dans une céramique texturée YBaCuO dopée au BaSnO3. Elle présente des valeurs de J_c (77 K) de 7,1 × 10^4 A cm^{-2} en champ magnétique nul et de 1.1 × 10^4 A cm^{-2} sous 20 T. Une étude systématique de cette céramique a été entreprise. La microstructure et la nanostructure observées respectivement en microscopie électronique à balayage SEM et en microscopie à haute résolution HREM ont été corrélées avec les mesures de J_c. On observe dans cette céramique une microstructure texturée contenant de nombreuses inclusions de phase verte (taille leq 10 μm) et un très faible nombre d'inclusions de BaSnO3 (taille < 1 μm). Les valeurs de J

Nearly massless Dirac fermions hosted by Sb square net in BaMnSb2

PubMed Central

Liu, Jinyu; Hu, Jin; Cao, Huibo; Zhu, Yanglin; Chuang, Alyssa; Graf, D.; Adams, D. J.; Radmanesh, S. M. A.; Spinu, L.; Chiorescu, I.; Mao, Zhiqiang

2016-01-01

Layered compounds AMnBi2 (A = Ca, Sr, Ba, or rare earth element) have been established as Dirac materials. Dirac electrons generated by the two-dimensional (2D) Bi square net in these materials are normally massive due to the presence of a spin-orbital coupling (SOC) induced gap at Dirac nodes. Here we report that the Sb square net in an isostructural compound BaMnSb2 can host nearly massless Dirac fermions. We observed strong Shubnikov-de Haas (SdH) oscillations in this material. From the analyses of the SdH oscillations, we find key signatures of Dirac fermions, including light effective mass (~0.052m0; m0, mass of free electron), high quantum mobility (1280 cm2V−1S−1) and a π Berry phase accumulated along cyclotron orbit. Compared with AMnBi2, BaMnSb2 also exhibits much more significant quasi two-dimensional (2D) electronic structure, with the out-of-plane transport showing nonmetallic conduction below 120 K and the ratio of the out-of-plane and in-plane resistivity reaching ~670. Additionally, BaMnSb2 also exhibits a G-type antiferromagnetic order below 283 K. The combination of nearly massless Dirac fermions on quasi-2D planes with a magnetic order makes BaMnSb2 an intriguing platform for seeking novel exotic phenomena of massless Dirac electrons. PMID:27466151

75 FR 11563 - Jovencio L. Raneses, M.D.; Denial of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-11

... DEPARTMENT OF JUSTICE Drug Enforcement Administration Jovencio L. Raneses, M.D.; Denial of... Enforcement Administration, issued an Order to Show Cause to Jovencio L. Raneses, M.D. (Respondent), of San... issued by the Medical Board of California. See In re Jovencio L. Raneses, M.D., Default Decision and...

76 FR 48898 - Robert Leigh Kale, M.D., Decision and Order

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-09

... DEPARTMENT OF JUSTICE Drug Enforcement Administration Robert Leigh Kale, M.D., Decision and Order... Enforcement Administration, issued an Order to Show Cause to Robert Leigh Kale, M.D. (Registrant), of Fort... Certificate of Registration, BK9514375, issued to Robert Leigh Kale, M.D., be, and it hereby is, revoked. I...

78 FR 52802 - Tin T. Win, M.D., Dismissal of Proceeding

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-26

... DEPARTMENT OF JUSTICE Drug Enforcement Administration Tin T. Win, M.D., Dismissal of Proceeding On... Cause and Immediate Suspension of Registration to Tin T. Win, M.D. (hereinafter, Registrant), of Lake... order that the Order to Show Cause and Immediate Suspension of Registration issued to Tin T. Win, M.D...

76 FR 5686 - Drawbridge Operation Regulation; Pocomoke River, Pocomoke City, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-02

... Operation Regulation; Pocomoke River, Pocomoke City, MD AGENCY: Coast Guard, DHS. ACTION: Notice of... River, mile 15.6, at Pocomoke City, MD. The deviation restricts the operation of the draw span to.... The Route 675 Bridge across Pocomoke River, mile 15.6 at Pocomoke City MD, has a vertical clearance in...

76 FR 81826 - Drawbridge Operation Regulation; Pocomoke River, Pocomoke City, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-29

... Operation Regulation; Pocomoke River, Pocomoke City, MD AGENCY: Coast Guard, DHS. ACTION: Notice of... River, mile 15.6, at Pocomoke City, MD. The deviation restricts the operation of the draw span to... City, MD, has a vertical clearance in the closed position of three feet above mean high water. Under...

Synthesis and Characterization of BaFe12O19/Poly(aniline, pyrrole, ethylene terephthalate) Composites Coatings as Radar Absorbing Material (RAM)

NASA Astrophysics Data System (ADS)

Sasria, Nia; Ardhyananta, H.; Fajarin, R.; Widyastuti

2017-07-01

This research shows the processing and design of radar absorbing material (RAM) based on barium hexaferrite (BaM) and poly(aniline, pyrrole, ethylene terephthalate) (PAni,PPy,PET). BaM was prepared by sol gel method with Ni-Zn doping at mole fraction of 0. 4 to obtain soft magnetic material. BaM/(PAni,PPy) composites were synthesized by in-situ polymerization method at ˜0 °C. (BaM/PET) composite was prepared by melt compounding at 220°C. The composites were coated on A-grade AH36 steel using Dallenbach Layer, Salisbury Screen and Jaumann Layer methods with thickness of 2, 4, and 6 mm. The composites were evaluated using XRD, SEM, FTIR, VSM, LCM-meter and VNA. Results showed that doped BaM showed BaNixZnxFe12-2xO19 structure. BaM/(PAni,PPy,PET) composites possessed globular morphology with M-O and C-H bonds. BaNixZnxFe12-2xO19 exhibited the value of Ms and Hc, 56.6 emu/g and 60 Oe respectively. High electrical conductivity of 1.77744 × 10-5 S/cm was achieved of BaM/PAni composite. The maximum reflection loss (RL) was reached at - 48.720 dB and 8.1 GHz for BaM/PAni composite coating with 6 mm thickness at Jaumann Layer. These results indicated that BaM/PAni composite was a soft magnetic material with a high RL value that is suitable for RAM, which used in stealth technology on naval vessels.

ISYS-MD: A Surgeon's Influence on System Design

PubMed Central

Cavaye, Graham

1982-01-01

ISYS-MD, the Integrated SYStem in MUMPS for MD's, is a new design and a completely re-written system for a computerized medical record. It possesses the functionality of COSTAR combined with a comprehensive accountancy system. In addition, various ideas have been incorporated from the author's extensive experience in medical practice, making the system very practical in a clinical environment.

Spin-Coating and Characterization of Multiferroic MFe{sub 2}O{sub 4} (M=Co, Ni) / BaTiO{sub 3} Bilayers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quandt, Norman; Roth, Robert; Syrowatka, Frank

2016-01-15

Bilayer films of MFe{sub 2}O{sub 4} (M=Co, Ni) and BaTiO{sub 3} were prepared by spin coating of N,N-dimethylformamide/acetic acid solutions on platinum coated silicon wafers. Five coating steps were applied to get the desired thickness of 150 nm for both the ferrite and perovskite layer. XRD, IR and Raman spectroscopy revealed the formation of phase-pure ferrite spinels and BaTiO{sub 3}. Smooth surfaces with roughnesses in the order of 3 to 5 nm were found in AFM investigations. Saturation magnetization of 347 emu cm{sup −3} for the CoFe{sub 2}O{sub 4}/BaTiO{sub 3} and 188 emu cm{sup −3} for the NiFe{sub 2}O{sub 4}/BaTiO{submore » 3} bilayer, respectively were found. For the CoFe{sub 2}O{sub 4}/BaTiO{sub 3} bilayer a strong magnetic anisotropy was observed with coercivity fields of 5.1 kOe and 3.3 kOe (applied magnetic field perpendicular and parallel to film surface), while for the NiFe{sub 2}O{sub 4}/BaTiO{sub 3} bilayer this effect is less pronounced. Saturated polarization hysteresis loops prove the presence of ferroelectricity in both systems. - Graphical abstract: The SEM image of the CoFe{sub 2}O{sub 4}/BaTiO{sub 3} bilayer on Pt–Si-substrate (left), magnetization as a function of the magnetic field perpendicular and parallel to the film plane (right top) and P–E and I–V hysteresis loops of the bilayer at room temperature. - Highlights: • Ferrite and perovskite oxides grown on platinum using spin coating technique. • Columnar growth of cobalt ferrite particle on the substrate. • Surface investigation showed a homogenous and smooth surface. • Perpendicular and parallel applied magnetic field revealed a magnetic anisotropy. • Switching peaks and saturated P–E hysteresis loops show ferroelectricity.« less

76 FR 71369 - Robert G. Crummie, M.D.; Decision and Order

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-17

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 10-60] Robert G. Crummie, M.D... Registration, BC2964965, issued to Robert G. Crummie, M.D., be, and it hereby is, revoked. I further order that any pending application of Robert G. Crummie, M.D., to renew or modify his registration, be, and it...

78 FR 19012 - Pawan Kumar Jain, M.D.; Decision And Order

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-28

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 13-13] Pawan Kumar Jain, M.D...), I order that DEA Certificate of Registration BJ5128067, issued to Pawan Kumar Jain, M.D., be, and it hereby is, revoked. I further order that any pending application of Pawan Kumar Jain, M.D., to renew or...

75 FR 49955 - Hung Thien Ly, M.D.; Revocation of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-16

... DEPARTMENT OF JUSTICE Drug Enforcement Administration Hung Thien Ly, M.D.; Revocation of... Enforcement Administration, issued an Order to Show Cause to Hung Thien Ly, M.D. (Respondent), of McRae..., BL8586147, issued to Hung Thien Ly, M.D., be, and it hereby is, revoked. I further order that any pending...

Preparation of directionally solidified BaTi2O5-Ba6Ti17O40 eutectic by the floating zone method

NASA Astrophysics Data System (ADS)

Shiga, K.; Katsui, H.; Goto, T.

2017-02-01

The BaTi2O5-Ba6Ti17O40 eutectic (BaO-68.7 mol% TiO2) was directionally solidified by the floating zone (FZ) method and crystalline phases, microstructures and orientation were investigated. Ba6Ti17O40 with faceted rod-like shape was dispersed in the BaTi2O5 matrix. The growth directions of BaTi2O5 and Ba6Ti17O40 were parallel to the b and a axis, respectively, and the orientation relations were BaTi2O5 (010)//Ba6Ti17O40(60 2 ̅) and BaTi2O5 (001)//Ba6Ti17O40 (001).

Effect of Heat Treatment on The Crystal Structur, Electrical Conductivity and Surface of Ba1.5Sr0.5Fe2O5 Composite

NASA Astrophysics Data System (ADS)

Purwanto, P.; Adi, WA; Yunasfi

2017-05-01

The Composite of Ba1,5Sr0,5Fe2O5 has been synthesized by using powder metallurgy technique. The Ba1.5Sr0.5Fe2O5 were prepared from BaCO3, SrCO3 and Fe2O3 raw materials with a specific weight ratio. The three materials were synthesized by powder metallurgy under heat treatment at 800 °C, 900 °C, and 1000 °C for 5 hours. All the three samples were characterized by using X-ray Diffraction (XRD) to determine the crystal structure and crystal size, LCR meter to determine the conductivity, and Scanning Electron Microscope (SEM) to observe the morphological of the composites. The phase analysis result showed that the composite consists of several minor phases such as BaO2, SrO2, and Fe2O3. The Crystal size of composite Ba1.5Sr0.5Fe2O5 decreased while increases the strain of crystal with increasing of sintering temperature. The crystal size of the Ba1.5Sr0.5Fe2O5 composite is 3.55 nm to 7.23 nm and value of strain is 8.47% until 3.90%. Based on the conductivity measurement, it was obtained that the conductivity of the Ba1.5Sr0.5Fe2O5 composite decreased with increasing sintering temperature. It was also noticed that the conductivity increased with increasing of frequency. The conductivity ranged from 6.619×10-7 S/cm to 65.659×10-7 S/cm. The energy dispersive spectroscopy (EDS) analysis showed that several dominant elements were a good agreement with the phase analysis.

Reactions of NO2 with BaO/Pt(111) Model Catalysts: The Effects of BaO Film Thickness and NO2 Pressure on the Formation of Ba(NOx)2 Species

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mudiyanselage, Kumudu; Yi, Cheol-Woo; Szanyi, Janos

2011-05-31

The adsorption and reaction of NO2 on BaO (<1, ~3, and >20 monolayer equivalent (MLE))/Pt(111) model systems were studied with temperature programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS), and infrared reflection absorption spectroscopy (IRAS) under ultra-high vacuum (UHV) as well as elevated pressure conditions. NO2 reacts with sub-monolayer BaO (<1 MLE) to form nitrites only, whereas the reaction of NO2 with BaO (~3 MLE)/Pt(111) produces mainly nitrites and a small amount of nitrates under UHV conditions (PNO2 ~ 1.0 × 10-9 Torr) at 300 K. In contrast, a thick BaO(>20 MLE) layer on Pt(111) reacts with NO2 to form nitrite-nitratemore » ion pairs under the same conditions. At elevated NO2 pressures (≥ 1.0 × 10-5 Torr), however, BaO layers at all these three coverages convert to amorphous barium nitrates at 300 K. Upon annealing to 500 K, these amorphous barium nitrate layers transform into crystalline phases. The thermal decomposition of the thus-formed Ba(NOx)2 species is also influenced by the coverage of BaO on the Pt(111) substrate: at low BaO coverages, these species decompose at significantly lower temperatures in comparison with those formed on thick BaO films due to the presence of Ba(NOx)2/Pt interface where the decomposition can proceed at lower temperatures. However, the thermal decomposition of the thick Ba(NO3)2 films follows that of bulk nitrates. Results obtained from these BaO/Pt(111) model systems under UHV and elevated pressure conditions clearly demonstrate that both the BaO film thickness and the applied NO2 pressure are critical in the Ba(NOx)2 formation and subsequent thermal decomposition processes.« less

Room temperature metastable monoclinic phase in BaTiO3 crystals

NASA Astrophysics Data System (ADS)

Lummen, Tom; Wang, Jianjun; Holt, Martin; Kumar, Amit; Vlahos, Eftihia; Denev, Sava; Chen, Long-Qing; Gopalan, Venkatraman

2011-03-01

Low-symmetry monoclinic phases in ferroelectric materials are of considerable interest, due to their associated enhanced electromechanical coupling. Such phases have been found in Pb-based perovskite solid solutions such as lead zirconate titanate (PZT), where they form structural bridges between the rhombohedral and tetragonal ground states in compositional space. In this work, we directly image such a monoclinic phase in BaTi O3 crystals at room-temperature, using optical second harmonic generation, Raman, and X-ray microscopic imaging techniques. Phase-field modeling indicates that ferroelectric domain microstructures in BaTi O3 induce local inhomogeneous stresses in the crystals, which can effectively trap the transient intermediate monoclinic structure that occurs across the thermal orthorhombic-tetragonal phase boundary. The induced metastable monoclinic domains are ferroelectrically soft, being easily moved by electric fields as low as 0.5 kV cm-1 . Stabilizing such intermediate low-symmetry phases could very well lead to Pb-free materials with enhanced piezoelectric properties.

Anisotropic Dirac Fermions in BaMnBi2 and BaZnBi2

NASA Astrophysics Data System (ADS)

Ryu, Hyejin; Park, Se Young; Li, Lijun; Ren, Weijun; Petrovic, Cedomir; Hwang, Choonkyu; Mo, Sung-Kwan

We report electronic structures of BaMnBi2 and BaZnBi2 sharing similar structural properties but having different valence configuration of the Mn/Zn-Bi complex. Our angle-resolved photoemission measurements found a strong anisotropic Dirac dispersion in BaMnBi2 and a complete departure from the Dirac dispersion in BaZnBi2. Our findings, substantiated by the first principle calculations, allow us to understand role of Mn/Zn-Bi tetrahedra in the changes of the electronic structures as well as the effect of varying band filling of Bi-square net. Work at BNL was supported by the U.S. Dept of Energy-BES, Division of Materials Science and Engineering, under Contract No. DE-SC0012704 and Chinese Academy of Sciences under Grant No. KJZD-EW-M05.

Trends in MD/PhD Graduates Entering Psychiatry: Assessing the Physician-Scientist Pipeline.

PubMed

Arbuckle, Melissa R; Luo, Sean X; Pincus, Harold Alan; Gordon, Joshua A; Chung, Joyce Y; Chavez, Mark; Oquendo, Maria A

2018-06-01

The goal of this study was to identify trends in MD/PhD graduates entering psychiatry, to compare these trends with other specialties, and to review strategies for enhancing the physician-scientist pipeline. Data on 226,588 medical students graduating from Liaison Committee on Medical Education accredited programs between 1999 and 2012 (6626 MD/PhDs) were used to evaluate the number, percentage, and proportion of MD/PhDs entering psychiatry in comparison with other specialties (neurology, neurosurgery, internal medicine, family medicine, and radiation oncology). Linear regression and multiple linear regression determined whether these values increased over time and varied by sex. Over 14 years, an average of 18 MD/PhDs (range 13-29) enrolled in psychiatry each year. The number of MD/PhDs going into psychiatry significantly increased, although these gains were modest (less than one additional MD/PhD per year). The proportion of students entering psychiatry who were MD/PhDs varied between 2.9 and 5.9 per 100 residents, with no significant change over time. There was also no change in the percentage of MD/PhDs entering psychiatry from among all MD/PhD graduates. The rate of increase in the number of MD/PhDs going into psychiatry did not differ significantly from other specialties except for family medicine, which is decreasing. The rate of MD/PhDs going into psychiatry was higher for women, suggesting closure of the sex gap in 17 years. Despite the increase in the number of MD/PhDs entering psychiatry, these numbers remain low. Expanding the cohort of physician-scientists dedicated to translational research in psychiatry will require a multipronged approach.

[MD PhD programs: Providing basic science education for ophthalmologists].

PubMed

Spaniol, K; Geerling, G

2015-06-01

Enrollment in MD PhD programs offers the opportunity of a basic science education for medical students and doctors. These programs originated in the USA where structured programs have been offered for many years, but now German universities also run MD PhD programs. The MD PhD programs provided by German universities were investigated regarding entrance requirements, structure and financing modalities. An internet and telephone-based search was carried out. Out of 34 German universities 22 offered MD PhD programs. At 15 of the 22 universities a successfully completed course of studies in medicine was required for enrollment, 7 programs admitted medical students in training and 7 programs required a medical doctoral thesis, which had to be completed with at least a grade of magna cum laude in 3 cases. Financing required scholarships in many cases. Several German universities currently offer MD PhD programs; however, these differ considerably regarding entrance requirements, structure and financing. A detailed analysis investigating the success rates of these programs (e.g. successful completion and career paths of graduates) would be of benefit.

Improvement of the field-trapping capabilities of bulk Nd Ba Cu O superconductors using Ba Cu O substrates

NASA Astrophysics Data System (ADS)

Matsui, Motohide; Nariki, Shinya; Sakai, Naomichi; Iwafuchi, Kengo; Murakami, Masato

2006-07-01

We used Ba-Cu-O substrates to fabricate bulk Nd-Ba-Cu-O superconductors using a top-seeded melt-growth method. There were several advantages for the use of Ba-Cu-O substrate compared to conventional substrate materials such as MgO, ZrO2, Al2O3, RE123 and RE211 (RE = rare earth). The Ba-Cu-O did not react with the precursor and minimized liquid loss. Accordingly, the introduction of large-sized cracks was suppressed. We also found that Tc values were high at the bottom regions, which was ascribed to the beneficial effect of Ba-Cu-O in suppressing Nd/Ba substitution. As a result, we obtained bulk Nd-Ba-Cu-O superconductors that exhibited fairly good field-trapping capabilities, even at the bottom surfaces.

BGK-MD, Version 1.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haack, Jeffrey; Shohet, Gil

2016-12-02

The software implements a heterogeneous multiscale method (HMM), which involves solving a classical molecular dynamics (MD) problem and then computes the entropy production in order to compute the relaxation times towards equilibrium for use in a Bhatnagar-Gross-Krook (BGK) solver.

33 CFR 110.71a - Cabin Creek, Grasonville, Md.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Cabin Creek, Grasonville, Md. 110.71a Section 110.71a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71a Cabin Creek, Grasonville, Md. The waters...

33 CFR 110.71a - Cabin Creek, Grasonville, Md.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Cabin Creek, Grasonville, Md. 110.71a Section 110.71a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71a Cabin Creek, Grasonville, Md. The waters...

33 CFR 110.71a - Cabin Creek, Grasonville, Md.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Cabin Creek, Grasonville, Md. 110.71a Section 110.71a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71a Cabin Creek, Grasonville, Md. The waters...

33 CFR 110.71a - Cabin Creek, Grasonville, Md.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Cabin Creek, Grasonville, Md. 110.71a Section 110.71a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71a Cabin Creek, Grasonville, Md. The waters...

33 CFR 110.71a - Cabin Creek, Grasonville, Md.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Cabin Creek, Grasonville, Md. 110.71a Section 110.71a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71a Cabin Creek, Grasonville, Md. The waters...

Direct evidence of octupole deformation in neutron-rich 144Ba

DOE PAGES

Bucher, B.; Zhu, S.; Wu, C. Y.; ...

2016-03-17

Here, the neutron-rich nucleus 144Ba (t 1/2 = 11.5 s) is expected to exhibit some of the strongest octupole correlations among nuclei with mass numbers A less than 200. Until now, indirect evidence for such strong correlations has been inferred from observations such as enhanced E1 transitions and interleaving positive- and negative-parity levels in the ground-state band. In this experiment, the octupole strength was measured directly by sub-barrier, multistep Coulomb excitation of a post-accelerated 650-MeV 144Ba beam on a 1.0–mg/cm 2 208Pb target. The measured value of the matrix element, < 3 1–∥M(E3)∥0 1 + >= 0.65( +17 –23) ebmore » 3/2, corresponds to a reduced B(E3) transition probability of 48( +25 –34) W.u. This result represents an unambiguous determination of the octupole collectivity, is larger than any available theoretical prediction, and is consistent with octupole deformation.« less

Stellar Laboratories: 3. New Ba 5, Ba 6, and Ba 7 Oscillator Strengths and the Barium Abundance in the Hot White Dwarfs G191-B2B and RE 0503-289

NASA Technical Reports Server (NTRS)

Rauch, T.; Werner, K.; Quinet, P.; Kruk, Jeffrey Walter

2014-01-01

Context. For the spectral analysis of high-resolution and high-signal-to-noise (S/N) spectra of hot stars, state-of-the-art non-local thermodynamic equilibrium (NLTE) model atmospheres are mandatory. These are strongly dependent on the reliability of the atomic data that is used for their calculation. Aims. Reliable Ba 5-7 oscillator strengths are used to identify Ba lines in the spectra of the DA-type white dwarf G191-B2B and the DO-type white dwarf RE 0503-289 and to determine their photospheric Ba abundances. Methods. We newly calculated Ba v-vii oscillator strengths to consider their radiative and collisional bound-bound transitions in detail in our NLTE stellar-atmosphere models for the analysis of Ba lines exhibited in high-resolution and high-S/N UV observations of G191-B2B and RE 0503-289. Results. For the first time, we identified highly ionized Ba in the spectra of hot white dwarfs. We detected Ba vi and Ba vii lines in the Far Ultraviolet Spectroscopic Explorer (FUSE) spectrum of RE 0503-289. The Ba vi/Ba vii ionization equilibrium is well reproduced with the previously determined effective temperature of 70 000 K and surface gravity of log g=7.5. The Ba abundance is 3.5 +/- 0.5 × 10(exp-4) (mass fraction, about 23 000 times the solar value). In the FUSE spectrum of G191-B2B, we identified the strongest Ba vii line (at 993.41 Å) only, and determined a Ba abundance of 4.0 +/- 0.5 × 10(exp-6) (about 265 times solar). Conclusions. Reliable measurements and calculations of atomic data are a pre-requisite for stellar-atmosphere modeling. Observed Ba vi-vii line profiles in two white dwarfs' (G191-B2B and RE 0503-289) far-ultraviolet spectra were well reproduced with our newly calculated oscillator strengths. This allowed to determine the photospheric Ba abundance of these two stars precisely.

CoMD Implementation Suite in Emerging Programming Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haque, Riyaz; Reeve, Sam; Juallmes, Luc

CoMD-Em is a software implementation suite of the CoMD [4] proxy app using different emerging programming models. It is intended to analyze the features and capabilities of novel programming models that could help ensure code and performance portability and scalability across heterogeneous platforms while improving programmer productivity. Another goal is to provide the authors and venders with some meaningful feedback regarding the capabilities and limitations of their models. The actual application is a classical molecular dynamics (MD) simulation using either the Lennard-Jones method (LJ) or the embedded atom method (EAM) for primary particle interaction. The code can be extended tomore » support alternate interaction models. The code is expected ro run on a wide class of heterogeneous hardware configurations like shard/distributed/hybrid memory, GPU's and any other platform supported by the underlying programming model.« less

3MdB: the Mexican Million Models database

NASA Astrophysics Data System (ADS)

Morisset, C.; Delgado-Inglada, G.

2014-10-01

The 3MdB is an original effort to construct a large multipurpose database of photoionization models. This is a more modern version of a previous attempt based on Cloudy3D and IDL tools. It is accessed by MySQL requests. The models are obtained using the well known and widely used Cloudy photoionization code (Ferland et al, 2013). The database is aimed to host grids of models with different references to identify each project and to facilitate the extraction of the desired data. We present here a description of the way the database is managed and some of the projects that use 3MdB. Anybody can ask for a grid to be run and stored in 3MdB, to increase the visibility of the grid and the potential side applications of it.

P-type hole mobility measurement in Na-doped BaSnO3

NASA Astrophysics Data System (ADS)

Hong, Sungyun; Jang, Yeaju; Park, Jisung; Char, Kookrin

P-type doping in oxide materials has been a difficult task because of the oxygen vacancies. Taking advantage of the excellent oxygen stability in BaSnO3 (BSO), we replaced Ba with Na in BSO to achieve p-type doping. Ba1-xNaxSnO3 (BNSO) films with varying dopant ratios were epitaxially grown by the pulsed laser deposition technique. We confirmed that the BNSO films were properly grown and determined their lattice constants with respect to the dopant ratio by x-ray diffraction. Due to the high resistance of the films at room temperature, we measured the transport properties of the BNSO films at temperatures ranging from 200 C to 400 C. Hall resistance measurements in a +/- 5 kG magnetic field were performed to confirm that the films are indeed p-type. As the temperature increased, the hole carrier concentration of the films increased while the film resistance decreased. The hole mobility values, in the tens of cm2/Vsec range, were found to decrease with the temperature. We will present the complete doping rate and temperature dependence of the hole mobility and compare their behavior with those of n-type La-doped BSO. Samsung science and technology foundation.

Fe/starch nanoparticle - Pseudomonas aeruginosa: Bio-physiochemical and MD studies.

PubMed

Mofradnia, Soheil Rezazadeh; Tavakoli, Zahra; Yazdian, Fatemeh; Rashedi, Hamid; Rasekh, Behnam

2018-05-03

In this research, we attempt to study biosurfactant production by Pseudomonas aeruginosa using Fe/starch nanoparticles. Fe/starch showed no bacterial toxicity at 1 mg/ml and increased the growth rate and biosurfactant production up to 23.21 and 20.73%, respectively. Surface tension, dry weight cell, and emulsification indexes (E24) were measured. Biosurfactant production was considered via computational techniques and molecular dynamic (MD) simulation through flexible and periodic conditions (by material studio software) as well. The results of software predictions demonstrate by radial distribution function (RDF), density, energy and temperature graphs. According to the present experimental results, increased 30% growth of the bacterium has been observed and the subsequent production of biosurfactant. The difference between the experimental results and simulation data were achieved up to 0.17 g/cm 3 , which confirms the prediction of data by the software due to a difference of <14.5% (ideal error value is 20%). Copyright © 2017. Published by Elsevier B.V.

Ba3CuOs2O9 and Ba3ZnOs2O9, a comparative study

NASA Astrophysics Data System (ADS)

Feng, Hai L.; Jansen, Martin

2018-02-01

Polycrystalline samples of Ba3CuOs2O9 and Ba3ZnOs2O9 were synthesized by solid-state reactions. Ba3CuOs2O9 crystallizes in Cmcm, while Ba3ZnOs2O9 adopts the hexagonal space group P63/mmc. Both the crystal structures consist of face-sharing Os-centered octahedra forming dimer-like Os2O9 units, which are interconnected by corner-sharing CuO6, or ZnO6 octahedra, respectively. In Ba3CuOs2O9, the CuO6 octahedra show a characteristic Jahn-Teller distortion. Both, Ba3CuOs2O9 and Ba3ZnOs2O9, are electrically insulating. Magnetic and specific heat measurements confirm that Ba3CuOs2O9 is antiferromagnetically ordered below 47 K. Analysis of the magnetic data indicated that its magnetic properties are dominated by Cu2+ ions. The magnetic susceptibility of Ba3ZnOs2O9 is weakly temperature-dependent with a broad maximum ≈ 280 K, indicating the presence of strong exchange interactions within the Os2O9 dimer. The residual magnetic susceptibility at low temperatures also suggests the presence of appreciable exchange coupling between the dimers.

Barium bioaccumulation by bacterial biofilms and implications for Ba cycling and use of Ba proxies.

PubMed

Martinez-Ruiz, Francisca; Jroundi, Fadwa; Paytan, Adina; Guerra-Tschuschke, Isabel; Abad, María Del Mar; González-Muñoz, María Teresa

2018-04-24

Ba proxies have been broadly used to reconstruct past oceanic export production. However, the precise mechanisms underlying barite precipitation in undersaturated seawater are not known. The link between bacterial production and particulate Ba in the ocean suggests that bacteria may play a role. Here we show that under experimental conditions marine bacterial biofilms, particularly extracellular polymeric substances (EPS), are capable of bioaccumulating Ba, providing adequate conditions for barite precipitation. An amorphous P-rich phase is formed at the initial stages of Ba bioaccumulation, which evolves into barite crystals. This supports that in high productivity regions where large amounts of organic matter are subjected to bacterial degradation, the abundant EPS would serve to bind the necessary Ba and form nucleation sites leading to barite precipitation. This also provides new insights into barite precipitation and opens an exciting field to explore the role of EPS in mineral precipitation in the ocean.

33 CFR 110.71b - Wye River, Wye, Md.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Wye River, Wye, Md. 110.71b Section 110.71b Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71b Wye River, Wye, Md. The waters of a cove on the...

33 CFR 110.71b - Wye River, Wye, Md.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Wye River, Wye, Md. 110.71b Section 110.71b Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71b Wye River, Wye, Md. The waters of a cove on the...

33 CFR 110.71b - Wye River, Wye, Md.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Wye River, Wye, Md. 110.71b Section 110.71b Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71b Wye River, Wye, Md. The waters of a cove on the...

33 CFR 110.71b - Wye River, Wye, Md.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Wye River, Wye, Md. 110.71b Section 110.71b Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71b Wye River, Wye, Md. The waters of a cove on the...

33 CFR 110.71b - Wye River, Wye, Md.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Wye River, Wye, Md. 110.71b Section 110.71b Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71b Wye River, Wye, Md. The waters of a cove on the...

Apple F-Box Protein MdMAX2 Regulates Plant Photomorphogenesis and Stress Response.

PubMed

An, Jian-Ping; Li, Rui; Qu, Feng-Jia; You, Chun-Xiang; Wang, Xiao-Fei; Hao, Yu-Jin

2016-01-01

MAX2 (MORE AXILLARY GROWTH2) is involved in diverse physiological processes, including photomorphogenesis, the abiotic stress response, as well as karrikin and strigolactone signaling-mediated shoot branching. In this study, MdMAX2, an F-box protein that is a homolog of Arabidopsis MAX2, was identified and characterized. Overexpression of MdMAX2 in apple calli enhanced the accumulation of anthocyanin. Ectopic expression of MdMAX2 in Arabidopsis exhibited photomorphogenesis phenotypes, including increased anthocyanin content and decreased hypocotyl length. Further study indicated that MdMAX2 might promote plant photomorphogenesis by affecting the auxin signaling as well as other plant hormones. Transcripts of MdMAX2 were noticeably up-regulated in response to NaCl and Mannitol treatments. Moreover, compared with the wild-type, the MdMAX2 -overexpressing apple calli and Arabidopsis exhibited increased tolerance to salt and drought stresses. Taken together, these results suggest that MdMAX2 plays a positive regulatory role in plant photomorphogenesis and stress response.

Pyramidal pits created by single highly charged ions in BaF{sub 2} single crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

El-Said, A. S.; Physics Department, Faculty of Science, Mansoura University, 35516 Mansoura; Heller, R.

2010-07-15

In various insulators, the impact of individual slow highly charged ions (eV-keV) creates surface nanostructures, whose size depends on the deposited potential energy. Here we report on the damage created on a cleaved BaF{sub 2} (111) surface by irradiation with 4.5xq keV highly charged xenon ions from a room-temperature electron-beam ion trap. Up to charge states q=36, no surface topographic changes on the BaF{sub 2} surface are observed by scanning force microscopy. The hidden stored damage, however, can be made visible using the technique of selective chemical etching. Each individual ion impact develops into a pyramidal etch pits, as canmore » be concluded from a comparison of the areal density of observed etch pits with the applied ion fluence (typically 10{sup 8} ions/cm{sup 2}). The dimensional analysis of the measured pits reveals the significance of the deposited potential energy in the creation of lattice distortions/defects in BaF{sub 2}.« less

Coarse-Grained MD Simulations and Protein-Protein Interactions: The Cohesin-Dockerin System.

PubMed

Hall, Benjamin A; Sansom, Mark S P

2009-09-08

Coarse-grained molecular dynamics (CG-MD) may be applied as part of a multiscale modeling approach to protein-protein interactions. The cohesin-dockerin interaction provides a valuable test system for evaluation of the use of CG-MD, as structural (X-ray) data indicate a dual binding mode for the cohesin-dockerin pair. CG-MD simulations (of 5 μs duration) of the association of cohesin and dockerin identify two distinct binding modes, which resemble those observed in X-ray structures. For each binding mode, ca. 80% of interfacial residues are predicted correctly. Furthermore, each of the binding modes identified by CG-MD is conformationally stable when converted to an atomistic model and used as the basis of a conventional atomistic MD simulation of duration 20 ns.

MD Simulations of P-Type ATPases in a Lipid Bilayer System.

PubMed

Autzen, Henriette Elisabeth; Musgaard, Maria

2016-01-01

Molecular dynamics (MD) simulation is a computational method which provides insight on protein dynamics with high resolution in both space and time, in contrast to many experimental techniques. MD simulations can be used as a stand-alone method to study P-type ATPases as well as a complementary method aiding experimental studies. In particular, MD simulations have proved valuable in generating and confirming hypotheses relating to the structure and function of P-type ATPases. In the following, we describe a detailed practical procedure on how to set up and run a MD simulation of a P-type ATPase embedded in a lipid bilayer using software free of use for academics. We emphasize general considerations and problems typically encountered when setting up simulations. While full coverage of all possible procedures is beyond the scope of this chapter, we have chosen to illustrate the MD procedure with the Nanoscale Molecular Dynamics (NAMD) and the Visual Molecular Dynamics (VMD) software suites.

Temperature-dependent electron paramagnetic resonance detect oxygen vacancy defects and Cr valence of tetragonal Ba(Ti1-xCrx)O3 ceramics

NASA Astrophysics Data System (ADS)

Han, Dan-Dan; Lu, Da-Yong; Meng, Fan-Ling; Yu, Xin-Yu

2018-03-01

Temperature-dependent electron paramagnetic resonance (EPR) study was employed to detect oxygen vacancy defects in the tetragonal Ba(Ti1-xCrx)O3 (x = 5%) ceramic for the first time. In the rhombohedral phase below -150 °C, an EPR signal at g = 1.955 appeared in the insulating Ba(Ti1-xCrx)O3 (x = 5%) ceramic with an electrical resistivity of 108 Ω cm and was assigned to ionized oxygen vacancy defects. Ba(Ti1-xCrx)O3 ceramics exhibited a tetragonal structure except Ba(Ti1-xCrx)O3 (x = 10%) with a tetragonal-hexagonal mixed phase and a first-order phase transition dielectric behavior (ε‧m > 11,000). Mixed valence Cr ions could coexist in ceramics, form CrTi‧-VOrad rad or CrTirad-TiTi‧ defect complexes and make no contribution to a dielectric peak shift towards low temperature.

75 FR 8749 - Dwayne LaFrantz Wilson, M.D.; Revocation of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-25

... DEPARTMENT OF JUSTICE Drug Enforcement Administration Dwayne LaFrantz Wilson, M.D.; Revocation of... Enforcement Administration, issued an Order to Show Cause to Dwayne LaFrantz Wilson, M.D. (Respondent), of... Registration, BW6030857, issued to Dwayne LaFrantz Wilson, M.D., be, and it hereby is, revoked. I further order...

Vacuum and low oxygen pressure influence on BaFe12O19 film deposited by pulse laser deposition

NASA Astrophysics Data System (ADS)

Kumar, Pawan; Gaur, Anurag; Choudhary, R. J.

2018-05-01

BaFe12O19 hexaferrite thin films are deposited on Si (111) substrate by the pulse laser deposition (PLD) technique in high vacuum 10-6 Torr and low oxygen pressure (10 mTorr) at 650°C substrate temperature. The effects of high vacuum and low pressure on magnetic and optical properties are studied. These films are characterized by the x-ray diffractometer (XRD), SQUID-VSM magnetometer, and Photo-luminescence spectroscopy. XRD pattern reveals that the BaFe12O19 film well formed in both environments without any impurity pick. High magnetic saturazation 317 emu/cm3 and coercivity 130 Oe are observed for the film deposited in vacuum. Photoluminescence emission spectrum of BaFe12O19 film reveals that the higher intensity emission peak at ˜372 nm under the excitation wavelength of 270 nm is observed for the film grown in vacuum.

Innovative methodology for the synthesis of Ba-M hexaferrite BaFe{sub 12}O{sub 19} nanoparticles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmed, M.A., E-mail: moala@47hotmail.com; Helmy, N.; El-Dek, S.I.

2013-09-01

Graphical abstract: Transmission electron microscope images for the BaFe12O19. - Highlights: • BaFe{sub 12}O{sub 19}nanoparticles were prepared in single-phase from organometallic precursors. • BaFe{sub 12}O{sub 19} possesses small size 65 nm, H{sub C} = 3695 Oe and M{sub s} = 58 emu/g. • This method of preparation could be extended in the synthesis of other metal oxide nanoparticles. - Abstract: In this piece of work, high quality and homogeneity, barium hexaferrite (BaM) BaFe{sub 12}O{sub 19} nanoparticles were prepared from organometallic precursors for the 1st time. This method is based on the formation of supramolecular crystal structure of Ba[Fe(H{sub 3}NCH{sub 2}CH{submore » 2}NH{sub 3})]Cl{sub 7}·8H{sub 2}O. The crystal structure, morphology and magnetic properties of BaFe{sub 12}O{sub 19} at two different annealing temperatures namely 1000 °C and 1200 °C were investigated using X-ray diffraction, transmission electron microscope TEM and vibrating sample magnetometry (VSM). The results show that monophasic nanoparticles of hexaferrites were obtained. Nanoparticles of crystallite size 40–50 nm distinguished by narrow distribution and excellent homogeneity were obtained with superior magnetic properties which suggested single-domain particles of Ba-M hexaferrite.« less

Tetrad effects in REE abundance patterns of chondrules from CM meteorites: Implications for aqueous alteration on the CM parent asteroid

NASA Astrophysics Data System (ADS)

Inoue, Mutsuo; Nakamura, Noboru; Kimura, Makoto

2009-09-01

Lanthanide tetrad effect in bulk chondrules from two moderately altered CM chondrites, Murchison and Yamato-793321 (Y-793321), are reported for the first time. Twenty-three chondrules were petrographically characterized and analyzed for 10 rare earth elements (REE) and other trace and major elements (Ba, Sr, Rb, K, Ca, Mg and Fe) using the precise isotope dilution technique. The results indicate systematic depletion (several times) of alkali and alkaline earths compared to CV and CO chondrules. Most of the porphyritic olivine (8 PO) and olivine-pyroxene (4 POP), porphyritic and radial pyroxene (2 PP, 1 RP), and granular olivine (1 GO) chondrules show a light-REE (L-REE) depleted, heavy-REE (H-REE) smoothly fractionated pattern composed of four (upward convex) segments possessing a relatively large negative Eu anomaly (CI-normalized La/Sm, Lu/Er and Eu/Eu* ratios = 0.3-1: Eu*, normal value). On the other hand, all barred-olivine (5 BO) chondrules, a few PO and POP indicate almost a flat L-REE pattern. In addition, regardless of their textural types, nearly half of the chondrules have a variable degree of Ce and Yb anomalies, and/or L/H-REE discontinuity, which is similar to CV and CO chondrules. The observed L- and H-convex REE patterns accompanied with the negative Eu anomaly is the first known case for chondrules as well as meteoritic materials, but have been previously reported for geological samples such as sedimentary rocks, late stage igneous and metamorphic rocks, and are explained as the lanthanide tetrad effect, which plausibly results from fluid-rock interaction. We suggest that the marked REE fractionations occurred by the selective incorporation of L-, H-REEs and Eu into alteration products in the matrix during alteration processes on the CM parent body, but that the gas/solid REE fractionation characteristics established in the nebula have basically remained unchanged. We suggest that the tetrad effects observed here represent a new index of physico

Significantly Enhanced Energy Storage Density by Modulating the Aspect Ratio of BaTiO3 Nanofibers

PubMed Central

Zhang, Dou; Zhou, Xuefan; Roscow, James; Zhou, Kechao; Wang, Lu; Luo, Hang; Bowen, Chris R.

2017-01-01

There is a growing need for high energy density capacitors in modern electric power supplies. The creation of nanocomposite systems based on one-dimensional nanofibers has shown great potential in achieving a high energy density since they can optimize the energy density by exploiting both the high permittivity of ceramic fillers and the high breakdown strength of the polymer matrix. In this paper, BaTiO3 nanofibers (NFs) with different aspect ratio were synthesized by a two-step hydrothermal method and the permittivity and energy storage of the P(VDF-HFP) nanocomposites were investigated. It is found that as the BaTiO3 NF aspect ratio and volume fraction increased the permittivity and maximum electric displacement of the nanocomposites increased, while the breakdown strength decreased. The nanocomposites with the highest aspect ratio BaTiO3 NFs exhibited the highest energy storage density at the same electric field. However, the nanocomposites with the lowest aspect ratio BaTiO3 NFs achieved the maximal energy storage density of 15.48 J/cm3 due to its higher breakdown strength. This contribution provides a potential route to prepare and tailor the properties of high energy density capacitor nanocomposites. PMID:28332636

Significantly Enhanced Energy Storage Density by Modulating the Aspect Ratio of BaTiO3 Nanofibers

NASA Astrophysics Data System (ADS)

Zhang, Dou; Zhou, Xuefan; Roscow, James; Zhou, Kechao; Wang, Lu; Luo, Hang; Bowen, Chris R.

2017-03-01

There is a growing need for high energy density capacitors in modern electric power supplies. The creation of nanocomposite systems based on one-dimensional nanofibers has shown great potential in achieving a high energy density since they can optimize the energy density by exploiting both the high permittivity of ceramic fillers and the high breakdown strength of the polymer matrix. In this paper, BaTiO3 nanofibers (NFs) with different aspect ratio were synthesized by a two-step hydrothermal method and the permittivity and energy storage of the P(VDF-HFP) nanocomposites were investigated. It is found that as the BaTiO3 NF aspect ratio and volume fraction increased the permittivity and maximum electric displacement of the nanocomposites increased, while the breakdown strength decreased. The nanocomposites with the highest aspect ratio BaTiO3 NFs exhibited the highest energy storage density at the same electric field. However, the nanocomposites with the lowest aspect ratio BaTiO3 NFs achieved the maximal energy storage density of 15.48 J/cm3 due to its higher breakdown strength. This contribution provides a potential route to prepare and tailor the properties of high energy density capacitor nanocomposites.

Significantly Enhanced Energy Storage Density by Modulating the Aspect Ratio of BaTiO3 Nanofibers.

PubMed

Zhang, Dou; Zhou, Xuefan; Roscow, James; Zhou, Kechao; Wang, Lu; Luo, Hang; Bowen, Chris R

2017-03-23

There is a growing need for high energy density capacitors in modern electric power supplies. The creation of nanocomposite systems based on one-dimensional nanofibers has shown great potential in achieving a high energy density since they can optimize the energy density by exploiting both the high permittivity of ceramic fillers and the high breakdown strength of the polymer matrix. In this paper, BaTiO 3 nanofibers (NFs) with different aspect ratio were synthesized by a two-step hydrothermal method and the permittivity and energy storage of the P(VDF-HFP) nanocomposites were investigated. It is found that as the BaTiO 3 NF aspect ratio and volume fraction increased the permittivity and maximum electric displacement of the nanocomposites increased, while the breakdown strength decreased. The nanocomposites with the highest aspect ratio BaTiO 3 NFs exhibited the highest energy storage density at the same electric field. However, the nanocomposites with the lowest aspect ratio BaTiO 3 NFs achieved the maximal energy storage density of 15.48 J/cm 3 due to its higher breakdown strength. This contribution provides a potential route to prepare and tailor the properties of high energy density capacitor nanocomposites.

Correlation of magnetoelectric coupling in multiferroic BaTiO{sub 3}-BiFeO{sub 3} superlattices with oxygen vacancies and antiphase octahedral rotations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lorenz, Michael, E-mail: mlorenz@physik.uni-leipzig.de; Schwinkendorf, Peter; Grundmann, Marius

2015-01-05

Multiferroic (BaTiO{sub 3}-BiFeO{sub 3}) × 15 multilayer heterostructures show high magnetoelectric (ME) coefficients α{sub ME} up to 24 V/cm·Oe at 300 K. This value is much higher than that of a single-phase BiFeO{sub 3} reference film (α{sub ME} = 4.2 V/cm·Oe). We found clear correlation of ME coefficients with increasing oxygen partial pressure during growth. ME coupling is highest for lower density of oxygen vacancy-related defects. Detailed scanning transmission electron microscopy and selected area electron diffraction microstructural investigations at 300 K revealed antiphase rotations of the oxygen octahedra in the BaTiO{sub 3} single layers, which are an additional correlated defect structure of the multilayers.

76 FR 20034 - Calvin Ramsey, M.D.; Revocation of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-11

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 10-25] Calvin Ramsey, M.D... Control, Drug Enforcement Administration, issued an Order to Show Cause to Calvin Ramsey, M.D. (Respondent.... Respondent's Resp., at 1. Therein, Respondent asserted that ``[d]ue process dictates that this Court must...

77 FR 37068 - Muzaffer Aslan, M.D.; Decision and Order

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-20

... DEPARTMENT OF JUSTICE Drug Enforcement Administration Muzaffer Aslan, M.D.; Decision and Order On... Cause and Immediate Suspension of Registration to Muzaffer Aslan, M.D. (hereinafter, Respondent), of Los....C. 824, of the CSA. Calvin Ramsey, 76 FR 20034, 20036 (2011) (other citations omitted); Brenton D...

Developing the MD Explorer

NASA Astrophysics Data System (ADS)

Howie, Philip V.

1993-04-01

The MD Explorer is an eight-seat twin-turbine engine helicopter which is being developed using integrated product definition (IPD) team methodology. New techniques include NOTAR antitorque system for directional control, a composite fuselage, an all-composite bearingless main rotor, and digital cockpit displays. Three-dimensional CAD models are the basis of the entire Explorer design. Solid models provide vendor with design clarification, removing much of the normal drawing interpretation errors.

Study of the structure, dielectric and ferroelectric behavior of BaBi{sub 4+δ}Ti{sub 4}O{sub 15} ceramics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khokhar, Anita, E-mail: mails4anita@gmail.com, E-mail: goyalphy@gmail.com; Goyal, Parveen K., E-mail: mails4anita@gmail.com, E-mail: goyalphy@gmail.com; Sreenivas, K.

2016-05-23

The structure and ferroelectric properties of excess bismuth doped barium bismuth titanate BaBi{sub 4+δ}Ti{sub 4}O{sub 15} (δ = 2 - 10 wt.%)) ceramics prepared by solid-state reaction method have been investigated. X-ray diffraction (XRD) confirms the formation of a single phase material with a change in the orthorhombic distortion with varying excess of bismuth content. There is no change in the phase transition temperature (T{sub m}) while the relaxor behaviour has been modified significantly with excess of bismuth doping. Saturated hysteresis loops with high remnant polarization (P{sub r} ~ 12.5  µC/cm{sup 2}), low coercive fields (E{sub c} ~ 26 kV/cm) aremore » measured and a high piezoelectric coefficient (d{sub 33} ~ 29 pC/N) is achieved in poled BaBi{sub 4}Ti{sub 4}O{sub 15} ceramics prepared with up to 8 wt.% of excess bismuth oxide. The improvement in the ferroelectric properties with increase in the excess bismuth content in BaBi{sub 4}Ti{sub 4}O{sub 15} ceramics has been explained in terms of changing oxygen vacancy concentration and structural relaxation. Tunable ferroelectric materials can be obtained by manipulating the doping amount of excess bismuth.« less

Dielectric and Energy Storage Properties of Ba0.65Sr0.35TiO3 Ceramics Modified by BiNbO4

NASA Astrophysics Data System (ADS)

Zheng, Yi; Zhang, Jihua; Wei, Meng; Dong, Xiangxiang; Huang, Jiapeng; Wu, Kaituo; Chen, Hongwei

2018-02-01

(1 - x) (Ba0.65Sr0.35TiO3)-xBiNbO4 (x = 0.0-0.15) ceramic were prepared by solid-state reaction method. The phase composition, microstructure, dielectric properties, polarization-electric field, breakdown strength and energy storage behaviors for the BiNbO4-modified Ba0.65Sr0.35TiO3 ceramics were investigated. With the addition of BiNbO4, the remnant polarization and saturation polarization decreased and the nonlinearity was suppressed. When x = 0.07, the maximum recoverable energy storage achieved was 0.5 J/cm3, 1.5 times that of un-doped Ba0.65Sr0.35TiO3 ceramics, with an efficiency of 96.89% and a breakdown electric field reaching 15.3 kV/mm. Therefore, BiNbO4 doping could improve the energy storage properties of Ba0.65Sr0.35TiO3 for high-energy pulse capacitor application.

Reduction in interface defect density in p-BaSi2/n-Si heterojunction solar cells by a modified pretreatment of the Si substrate

NASA Astrophysics Data System (ADS)

Yamashita, Yudai; Yachi, Suguru; Takabe, Ryota; Sato, Takuma; Emha Bayu, Miftahullatif; Toko, Kaoru; Suemasu, Takashi

2018-02-01

We have investigated defects that occurred at the interface of p-BaSi2/n-Si heterojunction solar cells that were fabricated by molecular beam epitaxy. X-ray diffraction measurements indicated that BaSi2 (a-axis-oriented) was subjected to in-plane compressive strain, which relaxed when the thickness of the p-BaSi2 layer exceeded 50 nm. Additionally, transmission electron microscopy revealed defects in the Si layer near steps that were present on the Si(111) substrate. Deep level transient spectroscopy revealed two different electron traps in the n-Si layer that were located at 0.33 eV (E1) and 0.19 eV (E2) below the conduction band edge. The densities of E1 and E2 levels in the region close to the heterointerface were approximately 1014 cm-3. The density of these electron traps decreased below the limits of detection following Si pretreatment to remove the oxide layers from the n-Si substrate, which involved heating the substrate to 800 °C for 30 min under ultrahigh vacuum while depositing a layer of Si (1 nm). The remaining traps in the n-Si layer were hole traps located at 0.65 eV (H1) and 0.38 eV (H2) above the valence band edge. Their densities were as low as 1010 cm-3. Following pretreatment, the current versus voltage characteristics of the p-BaSi2/n-Si solar cells under AM1.5 illumination were reproducible with conversion efficiencies beyond 5% when using a p-BaSi2 layer thickness of 100 nm. The origin of the H2 level is discussed.

76 FR 71370 - Silviu Ziscovici, M.D.; Decision and Order

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-17

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 11-3] Silviu Ziscovici, M.D.; Decision and Order On December 10, 2010, Administrative Law Judge (ALJ) Timothy D. Wing, issued the... Certificate of Registration, BZ4692756, issued to Silviu Ziscovici, M.D., be, and it hereby is, revoked. I...

Apoptosis of Corneal Epithelial Cells Caused by Ultraviolet B-induced Loss of K+ is Inhibited by Ba2+

PubMed Central

Glupker, Courtney D.; Boersma, Peter M.; Schotanus, Mark P.; Haarsma, Loren D.; Ubels, John L.

2017-01-01

UVB exposure at ambient outdoor levels triggers rapid K+ loss and apoptosis in human corneal limbal epithelial (HCLE) cells cultured in medium containing 5.5 mM K+, but considerably less apoptosis occurs when the medium contains the high K+ concentration that is present in tears (25 mM). Since Ba2+ blocks several K+ channels, we tested whether Ba2+-sensitive K+ channels are responsible for some or all of the UVB-activated K+ loss and subsequent activation of the caspase cascade and apoptosis. Corneal epithelial cells in culture were exposed to UVB at 80 or 150 mJ/cm2. Patch-clamp recording was used to measure UVB-induced K+ currents. Caspase-activity and TUNEL assays were performed on HCLE cells exposed to UVB followed by incubation in the presence or absence of Ba2+. K+ currents were activated in HCLE cells following UVB-exposure. These currents were reversibly blocked by 5 mM Ba2+. When HCLE cells were incubated with 5 mM Ba2+ after exposure to UVB, activation of caspases-9, -8, and -3 and DNA fragmentation were significantly decreased. The data confirm that UVB-induced K+ current activation and loss of intracellular K+ leads to activation of the caspase cascade and apoptosis. Extracellular Ba2+ inhibits UVB-induced apoptosis by preventing loss of intracellular K+ when K+ channels are activated. Ba2+ therefore has effects similar to elevated extracellular K+ in protecting HCLE cells from UVB-induced apoptosis. This supports our overall hypothesis that elevated K+ in tears contributes to protection of the corneal epithelium from adverse effects of ambient outdoor UVB. PMID:27189864

Critical current density in (YBa2Cu3O7-δ)1-x-(PrBa2Cu3O7-δ)x melt-textured composites

NASA Astrophysics Data System (ADS)

Opata, Yuri Aparecido; Monteiro, João Frederico Haas Leandro; Jurelo, Alcione Roberto; Siqueira, Ezequiel Costa

2018-06-01

Melt textured (YBa2Cu3O7-δ)1-x-(PrBa2Cu3O7-δ)x composites (x = 0.00 and x = 0.05) were grown using the top seeding method. The effect of the PrBa2Cu3O7-δ phase on the growth process and the modification of the microstructure as well as on the physical properties was analyzed. X-ray analyses indicated that both pure and Pr-doped samples present an orthorhombic superconducting phase. From resistivity measurements for YBa2Cu3O7-δ and (YBa2Cu3O7-δ)0.95-(PrBa2Cu3O7-δ)0.05 samples, the Tcab did not change and was around 90.5 K. However, from magnetic measurements, the superconductivity was observed in critical temperatures TC = 92.9 K and 92.4 K for YBa2Cu3O7-δ and (YBa2Cu3O7-δ)0.95-(PrBa2Cu3O7-δ)0.05 samples, respectively. The YBa2Cu3O7-δ sample showed higher critical current densities than those shown by the (YBa2Cu3O7-δ)0.95-(PrBa2Cu3O7-δ)0.05 sample, with values of JC = 5.85 × 105 A/cm2 and 4.72 × 105 A/cm2, respectively. This paper also discusses the importance of Pr substitution on nano- and micro-meter scales to enhance JC(H).

Experimental determination of the partition coefficient for Ba in Neogloboquadrina dutertrei suggests calcification occurs in a Ba-enriched microenvironment

NASA Astrophysics Data System (ADS)

Fehrenbacher, J. S.; Russell, A. D.; Davis, C. V.; Spero, H. J.; Chu, E.

2015-12-01

The Ba/Ca ratio in several spinose planktic foraminifer species varies as a function of the Ba/Ca concentration of seawater and is not affected by other parameters such as the seawater salinity, temperature and pH (Honisch et al., 2011). Since seawater Ba concentration is linearly related to Ba in nearshore environments, Ba/Ca ratios in spinose species shows promise as an indicator of past changes in monsoon strength and river runoff (e. g. Weldeab et al. 2007). In contrast, the non-spinose foraminifers often have intrashell variability in Ba/Ca, with Ba/Ca ratios much higher than expected for the range of Ba concentrations observed in the ocean. Furthermore, the Ba/Ca ratio can vary by over a factor of 10 within a single specimen. This suggests either 1) the partition coefficient for Ba in non-spinose species differs from that determined for spinose species, or 2) non-spinose species calcify in a micro-environment that is enriched in Ba. We conducted experiments on live specimens to determine the partition coefficient for Ba in the non-spinose foraminifer N. dutertrei. Specimens were collected via plankton net from the Southern California Bight and cultured at the Wrigley Marine Science Center, Santa Catalina Island during the summer of 2013-2015. We use isotopically labeled seawater (87Sr) to identify discrete portions of calcite that grew in culture. We use laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) for trace element analyses and to identify ocean grown vs. culture grown calcite. We show that the partition coefficient is similar to the spinose species: N. dutertrei incorporates Ba as a function of seawater chemistry. We conclude from these observations that N. dutertrei forms its calcite from fluids enriched in Ba, and hypothesize that this process occurs via attachment to organic-rich particles such as marine snow.

33 CFR 110.71 - Jacobs Nose Cove, Elk River, Md.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Jacobs Nose Cove, Elk River, Md. 110.71 Section 110.71 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71 Jacobs Nose Cove, Elk River, Md. The water...

33 CFR 110.71 - Jacobs Nose Cove, Elk River, Md.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Jacobs Nose Cove, Elk River, Md. 110.71 Section 110.71 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71 Jacobs Nose Cove, Elk River, Md. The water...

33 CFR 110.71 - Jacobs Nose Cove, Elk River, Md.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Jacobs Nose Cove, Elk River, Md. 110.71 Section 110.71 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71 Jacobs Nose Cove, Elk River, Md. The water...

33 CFR 110.71 - Jacobs Nose Cove, Elk River, Md.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Jacobs Nose Cove, Elk River, Md. 110.71 Section 110.71 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71 Jacobs Nose Cove, Elk River, Md. The water...

33 CFR 110.71 - Jacobs Nose Cove, Elk River, Md.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Jacobs Nose Cove, Elk River, Md. 110.71 Section 110.71 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.71 Jacobs Nose Cove, Elk River, Md. The water...

77 FR 24838 - Safety Zone; Magothy River, Sillery Bay, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-26

...-AA00 Safety Zone; Magothy River, Sillery Bay, MD AGENCY: Coast Guard, DHS. ACTION: Final rule. SUMMARY: The Coast Guard is establishing a safety zone in certain waters of the Magothy River, in Sillery Bay... a notice of proposed rulemaking (NPRM) entitled ``Safety Zone; Magothy River, Sillery Bay, MD'' in...

75 FR 30860 - Shepard Ginandes, M.D.; Revocation of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-02

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 10-14] Shepard Ginandes, M.D... Administration, issued an Order to Show Cause and Immediate Suspension of Registration to Shepard Ginandes, M.D... right to a hearing.'' Id. (citing 21 CFR 1301.43(d) & (e)). On September 30, 2009, the Order was served...

Analysis of MD5 authentication in various routing protocols using simulation tools

NASA Astrophysics Data System (ADS)

Dinakaran, M.; Darshan, K. N.; Patel, Harsh

2017-11-01

Authentication being an important paradigm of security and Computer Networks require secure paths to make the flow of the data even more secure through some security protocols. So MD-5(Message Digest 5) helps in providing data integrity to the data being sent through it and authentication to the network devices. This paper gives a brief introduction to the MD-5, simulation of the networks by including MD-5 authentication using various routing protocols like OSPF, EIGRP and RIPv2. GNS3 is being used to simulate the scenarios. Analysis of the MD-5 authentication is done in the later sections of the paper.

Ho3+/Yb3+ co-doped TeO2-BaF2-Y2O3 glasses for ∼1.2 μm laser applications

NASA Astrophysics Data System (ADS)

Wang, Shunbin; Li, Chengzhi; Yao, Chuanfei; Jia, Shijie; Jia, Zhixu; Qin, Guanshi; Qin, Weiping

2017-02-01

Intense ∼1.2 μm fluorescence is observed in Ho3+/Yb3+ co-doped TeO2-BaF2-Y2O3 glasses under 915 nm laser diode excitation. The 1.2 μm emission can be ascribed to the transition 5I6→5I8 of Ho3+. With the introducing of BaF2, the content of OH in the glasses drops markedly, and the 1.2 μm emission intensity increases gradually as increasing the concentration percentage of BaF2. Furthermore, microstructured fibers based on the TeO2-BaF2-Y2O3 glasses are fabricated by using a rod-in-tube method, and a relative positive gain of ∼9.42 dB at 1175.3 nm is obtained in a 5 cm long fiber.

Cummins MD & HD Accessory Hybridization CRADA -Annual Report FY15

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deter, Dean D.

2015-10-01

There are many areas of MD and HD vehicles that can be improved by new technologies and optimized control strategies. Component optimization and idle reduction need to be addressed, this is best done by a two part approach that includes selecting the best component technology, and/or architecture, and optimized controls that are vehicle focused. While this is a common focus in the light duty industry it has been gaining momentum in the MD and HD market as the market gets more competitive and the regulations become more stringent. When looking into systems optimization and idle reduction technologies, affected vehicle systemsmore » must first be considered, and if possible included in the new architecture to get the most benefit out of these new capabilities. Typically, when looking into idle reduction or component optimization for MD/HD, the vehicle s accessories become a prime candidate for electrification or hybridization. While this has already been studied on light duty vehicles (especially on hybrids and electric vehicles) it has not made any head way or market penetration in most MD and HD applications. If hybrids and electric MD and HD vehicles begin to break into the market this would be a necessary step into the ability to make those vehicles successful by allowing for independent, optimized operation separate from the engine.« less

BaBar Experiment Public Web Site

Science.gov Websites

spotlights BaBar time-reversal measurement. December 14, 2012 PhysicsWorld.com has selected the BaBar time . BaBar Makes First Direct Observation of Time-Reversal Violation August 30, 2012 Fundamental interactions among particles are oblivious to the direction of time (a movie of a rock thrown up and falling back

Stellar laboratories. III. New Ba v, Ba vi, and Ba vii oscillator strengths and the barium abundance in the hot white dwarfs G191-B2B and RE 0503-289

NASA Astrophysics Data System (ADS)

Rauch, T.; Werner, K.; Quinet, P.; Kruk, J. W.

2014-06-01

Context. For the spectral analysis of high-resolution and high-signal-to-noise (S/N) spectra of hot stars, state-of-the-art non-local thermodynamic equilibrium (NLTE) model atmospheres are mandatory. These are strongly dependent on the reliability of the atomic data that is used for their calculation. Aims: Reliable Ba v-vii oscillator strengths are used to identify Ba lines in the spectra of the DA-type white dwarf G191-B2B and the DO-type white dwarf RE 0503-289 and to determine their photospheric Ba abundances. Methods: We newly calculated Ba v-vii oscillator strengths to consider their radiative and collisional bound-bound transitions in detail in our NLTE stellar-atmosphere models for the analysis of Ba lines exhibited in high-resolution and high-S/N UV observations of G191-B2B and RE 0503-289. Results: For the first time, we identified highly ionized Ba in the spectra of hot white dwarfs. We detected Ba vi and Ba vii lines in the Far Ultraviolet Spectroscopic Explorer (FUSE) spectrum of RE 0503-289. The Ba vi/Ba vii ionization equilibrium is well reproduced with the previously determined effective temperature of 70 000 K and surface gravity of log g = 7.5. The Ba abundance is 3.5 ± 0.5 × 10-4 (mass fraction, about 23 000 times the solar value). In the FUSE spectrum of G191-B2B, we identified the strongest Ba vii line (at 993.41 Å) only, and determined a Ba abundance of 4.0 ± 0.5 × 10-6 (about 265 times solar). Conclusions: Reliable measurements and calculations of atomic data are a pre-requisite for stellar-atmosphere modeling. Observed Ba vi-vii line profiles in two white dwarfs' (G191-B2B and RE 0503-289) far-ultraviolet spectra were well reproduced with our newly calculated oscillator strengths. This allowed to determine the photospheric Ba abundance of these two stars precisely. Based on observations with the NASA/ESA Hubble Space Telescope, obtained at the Space Telescope Science Institute, which is operated by the Association of Universities for

33 CFR 110.70a - Northeast River, North East, Md.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Northeast River, North East, Md. 110.70a Section 110.70a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.70a Northeast River, North East, Md. The water...

33 CFR 110.70a - Northeast River, North East, Md.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Northeast River, North East, Md. 110.70a Section 110.70a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.70a Northeast River, North East, Md. The water...

33 CFR 110.70a - Northeast River, North East, Md.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Northeast River, North East, Md. 110.70a Section 110.70a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.70a Northeast River, North East, Md. The water...

33 CFR 110.70a - Northeast River, North East, Md.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Northeast River, North East, Md. 110.70a Section 110.70a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.70a Northeast River, North East, Md. The water...

33 CFR 110.70a - Northeast River, North East, Md.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Northeast River, North East, Md. 110.70a Section 110.70a Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.70a Northeast River, North East, Md. The water...

76 FR 71374 - Joseph Giacchino, M.D.; Decision and Order

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-17

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 10-54] Joseph Giacchino, M.D.; Decision and Order On July 9, 2010, Administrative Law Judge (ALJ) Timothy D. Wing, issued the attached... prevail. See, e.g., Bourne Pharmacy, 72 FR 18,273, 18,274 (2007); Agostino Carlucci, M.D., 49 FR 33,184...

Characterization of Y1-xCaxBa2Cu4O8 (x=0.0˜ 0.1) with Double Cu-O Chains by Raman Spectra

NASA Astrophysics Data System (ADS)

Kodama, Yasuharu; Tanemura, Sakae; Ikeda, Teruki

1991-08-01

Raman spectra of Y1-xCaxBa2Cu4O8 (x=0.0, 0.02, 0.05 and 0.1) ceramic samples synthesized under high oxygen pressure were investigated. Seven clear peaks assigned to Ag modes were observed for the sample with x=0. With increasing x, the peaks at 238 cm-1, 332 cm-1, 430 cm-1 and 590 cm-1 were broadened. The origin of the broadening of the peaks at 238 cm-1 and 590 cm-1 is considered to be the destruction of the double Cu-O chains due to the substitution of Ca for Y.

Swift heavy-ions induced sputtering in BaF2 thin films

NASA Astrophysics Data System (ADS)

Pandey, Ratnesh K.; Kumar, Manvendra; Singh, Udai B.; Khan, Saif A.; Avasthi, D. K.; Pandey, Avinash C.

2013-11-01

In our present experiment a series of barium fluoride thin films of different thicknesses have been deposited by electron beam evaporation technique at room temperature on silicon substrates. The effect of film thickness on the electronic sputter yield of polycrystalline BaF2 thin films has been reported in the present work. Power law for sputtered species collected on catcher grids has also been reported for film of lowest thickness. Sputtering has been performed by 100 MeV Au+28 ions. Atomic force microscopy (AFM) has been done to check the surface morphology of pristine samples. Glancing angle X-ray diffraction (GAXRD) measurements show that the pristine films are polycrystalline in nature and the grain size increases with increase in film thickness. Rutherford backscattering spectrometry (RBS) of pristine as well as irradiated films was done to determine the areal concentration of Ba and F atoms in the films. A reduction in the sputter yield of BaF2 films with the increase in film thickness has been observed from RBS results. The thickness dependence sputtering is explained on the basis of thermal spike and the energy confinement of the ions in the smaller grains. Also transmission electron microscopy (TEM) of the catchers shows a size distribution of sputtered species with values of power law exponent 1/2 and 3/2 for two fluences 5 × 1011 and 1 × 1012 ions/cm2, respectively.

Single-crystal-like, c-axis oriented BaTiO3 thin films with high-performance on flexible metal templates for ferroelectric applications

NASA Astrophysics Data System (ADS)

Shin, Junsoo; Goyal, Amit; Jesse, Stephen; Kim, Dae Ho

2009-06-01

Epitaxial, c-axis oriented BaTiO3 thin films were deposited using pulsed laser ablation on flexible, polycrystalline Ni alloy tape with biaxially textured oxide buffer multilayers. The high quality of epitaxial BaTiO3 thin films with P4mm group symmetry was confirmed by x-ray diffraction. The microscopic ferroelectric domain structure and the piezoelectric domain switching in these films were confirmed via spatially resolved piezoresponse mapping and local hysteresis loops. Macroscopic measurements demonstrate that the films have well-saturated hysteresis loops with a high remanent polarization of ˜11.5 μC/cm2. Such high-quality, single-crystal-like BaTiO3 films on low-cost, polycrystalline, flexible Ni alloy substrates are attractive for applications in flexible lead-free ferroelectric devices.

Tuning the electrocaloric effect by varying Sr concentration in ferroelectric Ba1 -xSrxTiO3

NASA Astrophysics Data System (ADS)

Lisenkov, S.; Ponomareva, I.

2018-05-01

The electrocaloric effect is investigated systematically in Ba1 -xSrxTiO3 ferroelectrics using a semiclassical direct computational approach. The data are reported for the technologically important range of Sr concentrations of 0.0-0.6, electric fields up to 1000 kV/cm, and temperatures ranging from 5 to 600 K. A detailed comparison of computational data with experimental data from the literature reveals semiquantitative agreement and suggests the origin of discrepancies. The electrocaloric change in temperature Δ T shows strong dependence on Sr concentration which offers a way to tune electrocaloric response. In particular, the maximum electrocaloric Δ T is found to decrease with the increase in Sr concentration, whereas the location of the maximum shifts towards lower temperatures following the Curie point of the ferroelectric. Surprisingly, the width of the peak in the dependence of Δ T on the initial temperature is independent of the Sr concentration but shows a strong dependence on the applied electric field. Computational data are used to propose a compositionally graded ferroelectric Ba0.70Sr0.30TiO3/Ba0.55Sr0.45TiO3/Ba0.50Sr0.50TiO3/Ba0.45Sr0.55TiO3 whose Δ T shows almost no temperature dependence in the technologically important range of temperatures and electric fields. Such a desirable feature could potentially lead to the enhancement of relative cooling power.

High transport current superconductivity in powder-in-tube Ba0.6K0.4Fe2As2 tapes at 27 T

NASA Astrophysics Data System (ADS)

Huang, He; Yao, Chao; Dong, Chiheng; Zhang, Xianping; Wang, Dongliang; Cheng, Zhe; Li, Jianqi; Awaji, Satoshi; Wen, Haihu; Ma, Yanwei

2018-01-01

The high upper critical field and low anisotropy of iron-based superconductors (IBS) make them particularly attractive for high-field applications, especially for the construction of next-generation nuclear magnetic resonance spectrometers, particle accelerators and high-field magnets. However, for practical use it is essential to make IBS materials into wire and tape conductors with sufficient current carrying capability, which is limited by misaligned grains inside the conductors. Here, based on a simple and low-cost powder-in-tube (PIT) method, we demonstrate a high transport critical current density (J c) reaching 1.5 × 105 A cm-2 (I c = 437 A) at 4.2 K and 10 T in Ba0.6K0.4Fe2As2 (Ba-122) tapes by texturing the grain orientation with optimized hot-press technique. The transport J c measured at 4.2 K under high magnetic fields of 27 T is still on the level of 5.5 × 104 A cm-2. Moreover, at 20 K and 5 T the transport J c is also as high as 5.4 × 104 A cm-2, showing a promising application potential in moderate temperature range which can be reached by liquid hydrogen or cryogenic cooling. All these J c values are the highest ever reported for IBS wires and tapes. The high-performance PIT Ba-122 tapes in this work suggest IBS to be a strong potential competitor of cuprate superconductors for the race of high-field applications in the future.

Trypsin-sensitive modulation of intestinal epithelial MD-2 as mechanism of lipopolysaccharide tolerance.

PubMed

Cario, Elke; Golenbock, Douglas T; Visintin, Alberto; Rünzi, Michael; Gerken, Guido; Podolsky, Daniel K

2006-04-01

Intestinal epithelial cells (IEC) are constantly exposed to both high concentrations of the bacterial ligand LPS and the serine protease trypsin. MD-2, which contains multiple trypsin cleavage sites, is an essential accessory glycoprotein required for LPS recognition and signaling through TLR4. The aim of this study was to characterize the expression and subcellular distribution of intestinal epithelial MD-2 and to delineate potential functional interactions with trypsin and then alteration in inflammatory bowel disease (IBD). Although MD-2 protein expression was minimal in primary IEC of normal colonic or ileal mucosa, expression was significantly increased in IEC from patients with active IBD colitis, but not in ileal areas from patients with severe Crohn's disease. Endogenous MD-2 was predominantly retained in the calnexin-calreticulin cycle of the endoplasmic reticulum; only a small fraction was exported to the Golgi. MD-2 expression correlated inversely with trypsin activity. Biochemical evidence and in vitro experiments demonstrated that trypsin exposure resulted in extensive proteolysis of endogenous and soluble MD-2 protein, but not of TLR4 in IEC, and was associated with desensitization of IEC to LPS. In conclusion, the present study suggests that endoplasmic reticulum-associated MD-2 expression in IBD may be altered by ileal protease in inflammation, leading to impaired LPS recognition and hyporesponsiveness through MD-2 proteolysis in IEC, thus implying a physiologic mechanism that helps maintain LPS tolerance in the intestine.

A pilot study of MD (psychiatry) theses-based research.

PubMed

Srivastava, Shrikant; Agarwal, Vivek; Subramanyam, Alka; Srivastava, Mona; Sathyanarayana Rao, T S; Rao, G Prasad; Khurana, Hitesh; Singh, Archana

2018-01-01

Undertaking a research project is mandatory for MD Psychiatry trainees. The present study was undertaken to assess the type of research activity being undertaken as part of MD Psychiatry dissertation, and its contribution to national and international literature. Three medical colleges supplied the data about the topic, names of the supervisor and the candidate, collaboration, funding accrued, and publication details of MD-based research carried out between years 2000 and 2010 inclusive; 95 records were collected for the final analysis. The details of the publications provided were cross-checked on the internet, which would have taken care of missed publications as well. Most studies were single-point assessment clinical studies. Only 2 studies had been funded, 11 had collaboration with other departments within the same institute, and 5 had inter-institute collaborations. Majority of the studies were not published. Only 30 were published as full paper and 9 as abstracts. Of these 30 full publications, only 3 were published in journals having JCI impact factor values (1.4, 1.3, and 1.4, respectively). The main finding of this pilot study was that MD-based research has low contribution to the national and international literature, and those articles which are published are in low impact journals. Suggestions for modifying this state of affairs are discussed.

Thermally-Induced Loss of Piezoelectricity in Ferroelectric Na0.5Bi0.5TiO3-BaTiO3

DTIC Science & Technology

2014-01-01

state laser as the excitation source. The laser light was focused on the (mirror-polished) sample surface by means of a long working distance 100...Ba or Na at the perovskite A-site, which is expected to impact the vibrational modes associated with the oxygen octahedron (above 200 cm1) [25

Processing of high performance (LRE)-Ba Cu O large, single-grain bulk superconductors in air

NASA Astrophysics Data System (ADS)

Hari Babu, N.; Iida, K.; Shi, Y.; Cardwell, D. A.

2006-10-01

We report the fabrication of large (LRE)BCO single-grains with improved superconducting properties for LRE = Nd, Sm and Gd using a practical process via both conventional top seeded melt growth (TSMG) and seeded infiltration-growth (SIG). This process uses a new generic seed crystal that promotes heterogeneous grain nucleation in the required orientation and suppresses the formation of solid solution in a controlled manner within individual grains by the addition of excess BaO2 to the precursor powder. The spatial distribution of the superconducting properties of LRE bulk superconductors as a function of BaO2 addition for large (LRE)BCO grains fabricated in air by TSMG and SIG for LRE = Gd, Sm and Nd are compared. The optimum BaO2 content required to fabricate single-grain (LRE)BCO with high and homogeneous Tc is determined from these experiments for each LRE system. The irreversibility fields of (LRE)BCO bulk superconductors processed in air are as high as those processed in reduced PO2. Critical current densities in excess of 105 A/cm2 at 77 K and higher trapped fields have been achieved in optimized (LRE)BCO superconductors fabricated in air for the first time.

Effect of heavy-ion irradiation on London penetration depth in overdoped Ba(Fe1-xCox)2As2

NASA Astrophysics Data System (ADS)

Murphy, J.; Tanatar, M. A.; Kim, Hyunsoo; Kwok, W.; Welp, U.; Graf, D.; Brooks, J. S.; Bud'ko, S. L.; Canfield, P. C.; Prozorov, R.

2013-08-01

Irradiation with 1.4 GeV 208Pb ions was used to induce artificial disorder in single crystals of iron-arsenide superconductor Ba(Fe1-xCox)2As2 and to study its effects on the temperature-dependent London penetration depth and transport properties. A study was undertaken on overdoped single crystals with x=0.108 and x=0.127 characterized by notable modulation of the superconducting gap. Irradiation corresponding to the matching fields of Bϕ=6 T and 6.5 T with doses 2.22×1011 d/cm2 and 2.4×1011 d/cm2, respectively, suppresses the superconducting Tc by approximately 0.3 to 1 K. The variation of the low-temperature penetration depth in both pristine and irradiated samples is well described by the power law Δλ(T)=ATn. Irradiation increases the magnitude of the prefactor A and decreases the exponent n, similar to the effect of irradiation in optimally-doped samples. This finding supports universal s± pairing in Ba(Fe1-xCox)2As2 compounds for the entire Co doping range.

Rhodotorula taiwanensis MD1149 produces hypoacetylated PEFA compounds with increased surface activity compared to Rhodotorula babjevae MD1169

PubMed Central

Rubinfeld, Bonnee; Leif, Roald; Mulcahy, Heather; Dugan, Lawrence; Souza, Brian

2018-01-01

Biosurfactants have several desirable characteristics in the industrial sector: detergency, antimicrobial effects, skin hydration, and emulsibility. Several yeast glycolipids are currently being utilized in these capacities: sophorolipids, ustilagic acid, and mannosylerythritol lipids (MELs). An emerging class of glycolipids, termed polyol esters of fatty acids (PEFA), have recently been reported for Rhodotorula babjevae, a basidiomycetous yeast species that secretes hyperacetylated congeners of PEFA (typically with 3–6 acetylation modifications). While screening Rhodotorula species for surfactant production, we identified a new environmental isolate identified as Rhodotorula taiwanensis MD1149 that dropped the surface tension of the liquid medium, indicating that it produced a potent biosurfactant. Acid depolymerization of the purified biosurfactants, followed by gas chromatography-mass spectrometry (GC-MS) analysis revealed that the biosurfactants were composed of PEFA compounds composed mainly of mannitol and arabitol esters of 3-hydroxy fatty acid, 3-methoxy fatty acid, and fatty acids with a single double bond; chain lengths were mainly C16 and C18. Liquid chromatography-mass spectrometry (LC-MS) confirmed the predicted accurate mass of these compounds. Interestingly, PEFA compounds produced by Rhodotorula taiwanensis MD1149 were more surface active due to their hypoacetylation profile (0–4 acetylation modifications) compared to Rhodotorula babjevae MD1169. These disparate surface active properties, based on acetylation, change the hydrophilic-lipophilic balance (HLB) of these compounds, and their potential utility within industrial applications. PMID:29293588

Rhodotorula taiwanensis MD1149 produces hypoacetylated PEFA compounds with increased surface activity compared to Rhodotorula babjevae MD1169.

PubMed

Lyman, Mathew; Rubinfeld, Bonnee; Leif, Roald; Mulcahy, Heather; Dugan, Lawrence; Souza, Brian

2018-01-01

Biosurfactants have several desirable characteristics in the industrial sector: detergency, antimicrobial effects, skin hydration, and emulsibility. Several yeast glycolipids are currently being utilized in these capacities: sophorolipids, ustilagic acid, and mannosylerythritol lipids (MELs). An emerging class of glycolipids, termed polyol esters of fatty acids (PEFA), have recently been reported for Rhodotorula babjevae, a basidiomycetous yeast species that secretes hyperacetylated congeners of PEFA (typically with 3-6 acetylation modifications). While screening Rhodotorula species for surfactant production, we identified a new environmental isolate identified as Rhodotorula taiwanensis MD1149 that dropped the surface tension of the liquid medium, indicating that it produced a potent biosurfactant. Acid depolymerization of the purified biosurfactants, followed by gas chromatography-mass spectrometry (GC-MS) analysis revealed that the biosurfactants were composed of PEFA compounds composed mainly of mannitol and arabitol esters of 3-hydroxy fatty acid, 3-methoxy fatty acid, and fatty acids with a single double bond; chain lengths were mainly C16 and C18. Liquid chromatography-mass spectrometry (LC-MS) confirmed the predicted accurate mass of these compounds. Interestingly, PEFA compounds produced by Rhodotorula taiwanensis MD1149 were more surface active due to their hypoacetylation profile (0-4 acetylation modifications) compared to Rhodotorula babjevae MD1169. These disparate surface active properties, based on acetylation, change the hydrophilic-lipophilic balance (HLB) of these compounds, and their potential utility within industrial applications.

Identification and expression analysis of the IPT and CKX gene families during axillary bud outgrowth in apple (Malus domestica Borkh.).

PubMed

Tan, Ming; Li, Guofang; Qi, Siyan; Liu, Xiaojie; Chen, Xilong; Ma, Juanjuan; Zhang, Dong; Han, Mingyu

2018-04-20

Cytokinins (CKs) play a crucial role in promoting axillary bud outgrowth and targeting the control of CK metabolism can be used to enhance branching in plants. CK levels are maintained mainly by CK biosynthesis (isopentenyl transferase, IPT) and degradation (dehydrogenase, CKX) genes in plants. A systematic study of the IPT and CKX gene families in apple, however, has not been conducted. In the present study, 12 MdIPTs and 12 MdCKXs were identified in the apple genome. Systematic phylogenetic, structural, and synteny analyses were performed. Expression analysis of these genes in different tissues was also assessed. MdIPT and MdCKX genes exhibit distinct expression patterns in different tissues. The response of MdIPT, MdCKX, and MdPIN1 genes to various treatments (6-BA, decapitation and Lovastatin, an inhibitor of CKs synthesis) that impact branching were also investigated. Results indicated that most of the MdIPT and MdCKX, and MdPIN1 genes were upregulated by 6-BA and decapitation treatment, but inhibited by Lovastatin, a compound that effectively suppresses axillary bud outgrowth induced by decapitation. These findings suggest that cytokinin biosynthesis is required for the activation of bud break and the export of auxin from buds in apple tree with intact primary shoot apex or decapitated apple tree. MdCKX8 and MdCKX10, however, exhibited little response to decapitation, but were significantly up-regulated by 6-BA and Lovastatin, a finding that warrants further investigation in order to understand their function in bud-outgrowth. Copyright © 2018 Elsevier B.V. All rights reserved.

Parallel cascade selection molecular dynamics (PaCS-MD) to generate conformational transition pathway

NASA Astrophysics Data System (ADS)

Harada, Ryuhei; Kitao, Akio

2013-07-01

Parallel Cascade Selection Molecular Dynamics (PaCS-MD) is proposed as a molecular simulation method to generate conformational transition pathway under the condition that a set of "reactant" and "product" structures is known a priori. In PaCS-MD, the cycle of short multiple independent molecular dynamics simulations and selection of the structures close to the product structure for the next cycle are repeated until the simulated structures move sufficiently close to the product. Folding of 10-residue mini-protein chignolin from the extended to native structures and open-close conformational transition of T4 lysozyme were investigated by PaCS-MD. In both cases, tens of cycles of 100-ps MD were sufficient to reach the product structures, indicating the efficient generation of conformational transition pathway in PaCS-MD with a series of conventional MD without additional external biases. Using the snapshots along the pathway as the initial coordinates, free energy landscapes were calculated by the combination with multiple independent umbrella samplings to statistically elucidate the conformational transition pathways.

Detection of Thermal 2 cm and 1 cm Formaldehyde Emission in NGC 7538

NASA Astrophysics Data System (ADS)

Yuan, Liang; Araya, E. D.; Hofner, P.; Kurtz, S.; Pihlstrom, Y.

2011-05-01

Formaldehyde is a tracer of high density gas in massive star forming regions. The K-doublet lines from the three lowest rotational energy levels of ortho-formaldehyde correspond to wavelengths of 6, 2 and 1 cm. Thermal emission of these transitions is rare, and maser emission has only been detected in the 6 cm line. NGC 7538 is an active site of massive star formation in the Galaxy, and one of only a few regions known to harbor 6 cm formaldehyde (H2CO) masers. Using the NRAO 100 m Green Bank Telescope (GBT), we detected 2 cm H2CO emission toward NGC 7538 IRS1. The velocity of the 2 cm H2CO line is very similar to the velocity of one of the 6 cm H2CO masers but the linewidth is greater. To investigate the nature of the 2 cm emission, we conducted observations of the 1 cm H2CO transition, and obtained a cross-scan map of the 2 cm line. We detected 1 cm emission and found that the 2 cm emission is extended (greater than 30"), which implies brightness temperatures of ˜0.2 K. Assuming optically thin emission, LTE, and that the 1 cm and 2 cm lines originate from the same volume of gas, both these detections are consistent with thermal emission of gas at ˜30 K. We conclude that the 1 cm and 2 cm H2CO lines detected with the GBT are thermal, which implies molecular densities above ˜105 cm-3. LY acknowledges support from WIU. PH acknowledges partial support from NSF grant AST-0908901.

Cell lines, Md108 and Md66, from the hemocytes of Malacosoma disstria (Lepidoptera) display aspects of plasma-free innate non-self activities.

PubMed

Lapointe, Jason F; Dunphy, Gary B; Giannoulis, Paschalis; Mandato, Craig A; Nardi, James B; Gharib, Osama H; Niven, Donald F

2011-11-01

The innate non-self response systems of the deciduous tree pest, the forest tent caterpillar, Malacosoma disstria has been documented by us in terms of in vitro and in vivo reactions towards the Gram-positive nonpathogenic bacterium, Bacillus subtilis and Gram-negative pathogenic microbe, Xenorhabdus nematophila and their respective surface antigens, lipopoteichoic acids (LTA) and lipopolysaccharides (LPS). These studies, often conducted in whole and diluted hemolymph, preclude examination of plasma-free cellular (hemocyte) responses. Plasma-free hemocytes as primary cultures are difficult to obtain. The floating cell line Md66 and attached cell line Md108 from M. disstria hemocytes were examined as a model for plasma-free M. disstria hemocyte non-self responses. Herein, it was established that although both lines differed from each other and from the primary hemocyte cultures of M. disstria in growth parameters, cell composition and sizes both cell lines displayed granular cell-like (GL) cells and plasmatocyte-like (PL) cells according to morphological criteria and to some extent antigenic similarities based on labeling with anti-Chrysodeixis includens hemocyte monoclonal antibodies. Hemocyte-specific neuroglian-like protein was detected on cells of both cell lines and in the primary hemocyte cultures albeit with staining patterns differing according to culture and cell types, confluency levels and cell-cell adhesion. Both cell lines bound B. subtilis and X. nematophila, the reaction extent varying with the cell line and its cell types. LPS damaged both cell types in the two cell lines whereas LTA enhanced the adhesion of Md66 GL cells to flask surfaces followed by PL cell adhesion. PL cells of both lines, like the primary cultures, phagocytosed FITC-labeled B. subtilis; only Md108 GL cells phagocytosed B. subtilis. In either case phagocytosis was always less in frequency and intensity than the primary cultures. Proteins released from the cell lines differed in

REPRODUCTION IN VITRO OF ENTAMŒBA TETRAGENA AND ENTAMŒBA COLI FROM THEIR CYSTS

PubMed Central

Yoshida, Kazuyoshi

1920-01-01

1. The vegetative forms of amebæ may be developed in vitro from the cysts. 2. The cysts of Entamœba tetragena and Entamœba coli each produce only a single vegetative individual. It has not been observed in vitro that a number of daughter amebæ, corresponding to the number of nuclei present in the cyst, emerge from the mother cyst, as claimed by Casagrandi and Barbagallo, Schaudinn, and a number of other investigators. 3. The daughter nuclei in the cystic stage correspond to the gamete nuclei of other protozoa. The syngamic nuclear union in the case of these two amebæ does not take place in the tetranuclear stage of the cyst, as claimed by Schaudinn and Wenyon, but during reproduction. 4. The process of autogamy of both amebæ is not restricted to two nuclei; it may involve more than two, which unite to form a syncaryon. In the case of all other protozoa, autogamy is restricted to two nuclei. 5. In order to distinguish the two types of autogamy, one has been termed simple autogamy and the other polynuclear autogamy. The latter may again be classified according to the number of nuclei involved, as trinuclear and tetranuclear autogamy. 6. The majority of cysts treated for 5 minutes in a 2 per cent solution of hydrochloric acid survives. 7. It was possible to demonstrate in vitro the developmental cycle of Entamœba tetragena. 8. No evidence of heterogamy has been observed in vitro in Entamœba tetragena or Entamœba coli. 9. The vegetative form of Entamœba tetragena, at a certain stage of its life cycle in vitro, shortly after its formation, has not only one or two, but may have as many as three or four nuclei. PMID:19868451

Manufacture of barium hexaferrite (BaO3.98Fe2O3) from iron oxide waste of grinding process by using calcination process

NASA Astrophysics Data System (ADS)

Idayanti, N.; Dedi; Kristiantoro, T.; Mulyadi, D.; Sudrajat, N.; Alam, G. F. N.

2018-03-01

The utilization of iron oxide waste of grinding process as raw materials for making barium hexaferrite has been completed by powder metallurgy method. The iron oxide waste was purified by roasting at 800 °C temperature for 3 hours. The method used varying calcination temperature at 1000, 1100, 1200, and 1250 °C for 3 hours. The starting iron oxide waste (Fe2O3) and barium carbonate (BaCO3) were prepared by mol ratio of Fe2O3:BaCO3 from the formula BaO3.98Fe2O3. Some additives such as calcium oxide (CaO), silicon dioxide (SiO2), and polyvinyl alcohol (PVA) were added after calcination process. The samples were formed at the pressure of 2 ton/cm2 and sintered at the temperature of 1250 °C for 1 hour. The formation of barium hexaferrite compounds after calcination is determined by X-Ray diffraction. The magnetic properties were observed by Permagraph-Magnet Physik with the optimum characteristic at calcination temperature of 1250 °C with the induction of remanence (Br) = 1.38 kG, coercivity (HcJ) = 4.533 kOe, product energy maximum (BHmax) = 1.086 MGOe, and density = 4.33 g/cm3.

Center of excellence for mobile sensor data-to-knowledge (MD2K).

PubMed

Kumar, Santosh; Abowd, Gregory D; Abraham, William T; al'Absi, Mustafa; Beck, J Gayle; Chau, Duen Horng; Condie, Tyson; Conroy, David E; Ertin, Emre; Estrin, Deborah; Ganesan, Deepak; Lam, Cho; Marlin, Benjamin; Marsh, Clay B; Murphy, Susan A; Nahum-Shani, Inbal; Patrick, Kevin; Rehg, James M; Sharmin, Moushumi; Shetty, Vivek; Sim, Ida; Spring, Bonnie; Srivastava, Mani; Wetter, David W

2015-11-01

Mobile sensor data-to-knowledge (MD2K) was chosen as one of 11 Big Data Centers of Excellence by the National Institutes of Health, as part of its Big Data-to-Knowledge initiative. MD2K is developing innovative tools to streamline the collection, integration, management, visualization, analysis, and interpretation of health data generated by mobile and wearable sensors. The goal of the big data solutions being developed by MD2K is to reliably quantify physical, biological, behavioral, social, and environmental factors that contribute to health and disease risk. The research conducted by MD2K is targeted at improving health through early detection of adverse health events and by facilitating prevention. MD2K will make its tools, software, and training materials widely available and will also organize workshops and seminars to encourage their use by researchers and clinicians. © The Author 2015. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Molecular Dynamics Simulations and XAFS (MD-XAFS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schenter, Gregory K.; Fulton, John L.

2017-01-20

MD-XAFS (Molecular Dynamics X-ray Adsorption Fine Structure) makes the connection between simulation techniques that generate an ensemble of molecular configurations and the direct signal observed from X-ray measurement.

MdHB1 down-regulation activates anthocyanin biosynthesis in the white-fleshed apple cultivar 'Granny Smith'.

PubMed

Jiang, Yonghua; Liu, Cuihua; Yan, Dan; Wen, Xiaohong; Liu, Yanli; Wang, Haojie; Dai, Jieyu; Zhang, Yujie; Liu, Yanfei; Zhou, Bin; Ren, Xiaolin

2017-02-01

Coloration in apple (Malus×domestica) flesh is mainly caused by the accumulation of anthocyanin. Anthocyanin is biosynthesized through the flavonoid pathway and regulated by MYB, bHLH, and WD40 transcription factors (TFs). Here, we report that the HD-Zip I TF MdHB1 was also involved in the regulation of anthocyanin accumulation. MdHB1 silencing caused the accumulation of anthocyanin in 'Granny Smith' flesh, whereas its overexpression reduced the flesh content of anthocyanin in 'Ballerina' (red-fleshed apple). Moreover, flowers of transgenic tobacco (Nicotiana tabacum 'NC89') overexpressing MdHB1 showed a remarkable reduction in pigmentation. Transient promoter activation assays and yeast one-hybrid results indicated that MdHB1 indirectly inhibited expression of the anthocyanin biosynthetic genes encoding dihydroflavonol-4-reductase (DFR) and UDP-glucose:flavonoid 3-O-glycosyltransferase (UFGT). Yeast two-hybrid and bimolecular fluorescence complementation determined that MdHB1 acted as a homodimer and could interact with MYB, bHLH, and WD40 in the cytoplasm, consistent with its cytoplasmic localization by green fluorescent protein fluorescence observations. Together, these results suggest that MdHB1 constrains MdMYB10, MdbHLH3, and MdTTG1 to the cytoplasm, and then represses the transcription of MdDFR and MdUFGT indirectly. When MdHB1 is silenced, these TFs are released to activate the expression of MdDFR and MdUFGT and also anthocyanin biosynthesis, resulting in red flesh in 'Granny Smith'. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Antinociceptive synergism of MD-354 and clonidine. Part II. The alpha-adrenoceptor component.

PubMed

Young, Shawquia; Vainio, Minna; Scheinin, Mika; Dukat, Małgorzata

2010-08-01

Previously, we reported that antinociceptive synergism of a 5-HT(3)/alpha(2)-adrenoceptor ligand MD-354 (m-chlorophenylguanidine) and clonidine combination occurs, in part, through a 5-HT(3) receptor antagonist mechanism. In the present investigation, a possible role for alpha(2)-adrenoceptors was examined. Mechanistic studies using yohimbine (a subtype non-selective alpha(2)-adrenoceptor antagonist), BRL 44408 (a preferential alpha(2A)-adrenoceptor antagonist) and imiloxan (a preferential alpha(2B/C)-adrenoceptor antagonist) on the antinociceptive actions of a MD-354/clonidine combination were conducted. Subcutaneous pre-treatment with all three antagonists inhibited the antinociceptive synergism of MD-354 and clonidine in the mouse tail-flick assay in a dose-dependent manner (AD(50) = 0.33, 2.1, and 0.17 mg/kg, respectively). Enhancement of clonidine antinociception by MD-354 did not potentiate clonidine's locomotor suppressant activity in a mouse locomotor assay. When [ethyl-3H]RS-79948-197 was used as radioligand, MD-354 displayed almost equal affinity to alpha(2A)- and alpha(2B)-adrenoceptors (K(i) = 110 and 220 nM) and showed lower affinity at alpha(2C)-adrenoceptors (K(i) = 4,700 nM). MD-354 had no subtype-selectivity for the alpha(2)-adrenoceptor subtypes as an antagonist in functional [35S]GTPgammaS binding assays. MD-354 was a weak partial agonist at alpha(2A)-adrenoceptors. Overall, in addition to the 5-HT(3) receptor component, the present investigation found MD-354 to be a weak partial alpha(2A)-adrenoceptor agonist that enhances clonidine's thermal antinociceptive actions through an alpha(2)-adrenoceptor-mediated mechanism without augmenting sedation.

Interior view, general view in covered causeway (MD1109W) near ward ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior view, general view in covered causeway (MD-1109-W) near ward 114, looking from the northwest - National Park Seminary, Music Hall, Linden Lane at western edge of campus, Silver Spring, Montgomery County, MD

A novel cobalt-free layered GdBaFe 2O 5+ δ cathode for proton conducting solid oxide fuel cells

NASA Astrophysics Data System (ADS)

Ding, Hanping; Xue, Xingjian

While cobalt-containing perovskite-type cathode materials facilitate the activation of oxygen reduction, they also suffer from problems like poor chemical stability in CO 2 and high thermal expansion coefficients. In this research, a cobalt-free layered GdBaFe 2O 5+ δ (GBF) perovskite was developed as a cathode material for protonic ceramic membrane fuel cells (PCMFCs) based on proton conducting electrolyte of stable BaZr 0.1Ce 0.7Y 0.2O 3- δ (BZCY7). The button cells of Ni-BZCY7|BZCY7|GBF were fabricated and characterized using complex impedance technique from 600 to 700 °C. An open-circuit potential of 1.007 V, maximum power density of 417 mW cm -2, and a low electrode polarization resistance of 0.18 Ω cm 2 were achieved at 700 °C. The results indicate that layered GBF perovskite is a good candidate for cobalt-free cathode material, while the developed Ni-BZCY7|BZCY7|GBF cell is a promising functional material system for solid oxide fuel cells.

Superconducting properties of Ba(Fe1-xNix)2As2 thin films in high magnetic fields

NASA Astrophysics Data System (ADS)

Richter, Stefan; Kurth, Fritz; Iida, Kazumasa; Pervakov, Kirill; Pukenas, Aurimas; Tarantini, Chiara; Jaroszynski, Jan; Hänisch, Jens; Grinenko, Vadim; Skrotzki, Werner; Nielsch, Kornelius; Hühne, Ruben

2017-01-01

We report on the electrical transport properties of epitaxial Ba(Fe1-xNix)2As2 thin films grown by pulsed laser deposition in static magnetic fields up to 35 T. The thin film shows a critical temperature of 17.2 K and a critical current density of 5.7 × 105 A/cm2 in self field at 4.2 K, while the pinning is dominated by elastic pinning at two-dimensional nonmagnetic defects. Compared to the single-crystal data, we find a higher slope of the upper critical field for the thin film at a similar doping level and a small anisotropy. Also, an unusual small vortex liquid phase was observed at low temperatures, which is a striking difference to Co-doped BaFe2As2 thin films.

Evidence for ProTα-TLR4/MD-2 binding: molecular dynamics and gravimetric assay studies.

PubMed

Omotuyi, Olaposi; Matsunaga, Hayato; Ueda, Hiroshi

2015-01-01

During preconditioning, lipopolysaccharide (LPS) selectively activates TLR4/MD-2/Toll/IL-1 receptor-domain-containing adaptor inducing IFN-β (TRIF) pathway instead of pro-inflammatory myeloid differentiation protein-88 (MyD88)/MyD88-adaptor-like protein (MAL) pathway. Extracellular prothymosin alpha (ProTα) is also known to selectively activate the TLR4/MD2/TRIF-IRF3 pathway in certain diseased conditions. In the current study, biophysical evidence for ProTα/TLR4/MD-2 complex formation and its interaction dynamics have been studied. Gravimetric assay was used to investigate ProTα/TLR4/MD-2 complex formation while molecular dynamics (MD) simulation was used to study its interaction dynamics. Through electrostatic interaction, full-length ProTα (F-ProTα) C-terminal peptide (aa 91 - 111) superficially interacts with similar TLR4/MD-2 (KD = 273.36 nm vs 16.07 μg/ml [LPS]) conformation with LPS at an overlapping three-dimensional space while F-ProTα is hinged to the TLR4 scaffold by one-amino acid shift-Mosoian domain (aa-51 - 90). Comparatively, F-ProTα better stabilizes MD-2 metastable states transition and mediates higher TLR4/MD-2 interaction than LPS. ProTα via its C-terminal peptide (aa 91 - 111) exhibits in vitro biophysical contact with TLR4/MD-2 complex conformation recognized by LPS at overlapping LPS-binding positions.

Studies of the TLR4-associated protein MD-2 using yeast-display and mutational analyses

PubMed Central

Mattis, Daiva M.; Chervin, Adam; Ranoa, Diana; Kelley, Stacy; Tapping, Richard; Kranz, David M.

2015-01-01

Bacterial lipopolysaccharide (LPS) activates the innate immune system by forming a complex with myeloid differentiation factor 2 (MD-2) and Toll-like receptor 4 (TLR4), which is present on antigen presenting cells. MD-2 plays an essential role in this activation of the innate immune system as a member of the ternary complex, TLR4:MD-2:LPS. With the goal of further understanding the molecular details of the interaction of MD-2 with LPS and TLR4, and possibly toward engineering dominant negative regulators of the MD-2 protein, here we subjected MD-2 to a mutational analysis using yeast display. The approach included generation of site-directed alanine mutants, and ligand-driven selections of MD-2 mutant libraries. Our findings showed that: 1) proline mutations in the F119-K132 loop that binds LPS were strongly selected for enhanced yeast surface stability, 2) there was a preference for positive-charged side chains (R/K) at residue 120 for LPS binding, and negative-charged side chains (D/E) for TLR4 binding, 3) aromatic residues were strongly preferred at F119 and F121 for LPS binding, and 4) an MD-2 mutant (T84N/D101A/S118A/S120D/K122P) exhibited increased binding to TLR4 but decreased binding to LPS. These studies revealed the impact of specific residues and regions of MD-2 on the binding of LPS and TLR4, and they provide a framework for further directed evolution of the MD-2 protein. PMID:26320630

Purification of oily wastewater by hybrid UF/MD.

PubMed

Gryta, M; Karakulski, K; Morawski, A W

2001-10-01

Investigations on the treatment of oily wastewater by a combination of ultrafiltration (UF) and membrane distillation (MD) as a final purification method have been performed. A tubular UF module equipped with polyvinylidene fluoride (PVDF) membranes and a capillary MD module with polypropylene membranes were tested using a typical bilge water collected from a harbour without pretreatment. The permeate obtained from the UF process generally contains less than 5 ppm of oil. A further purification of the UF permeate by membrane distillation results in a complete removal of oil from wastewater and a very high reduction of the total organic carbon (99.5%) and total dissolved solids (99.9%).

Direct NOE simulation from long MD trajectories.

PubMed

Chalmers, G; Glushka, J N; Foley, B L; Woods, R J; Prestegard, J H

2016-04-01

A software package, MD2NOE, is presented which calculates Nuclear Overhauser Effect (NOE) build-up curves directly from molecular dynamics (MD) trajectories. It differs from traditional approaches in that it calculates correlation functions directly from the trajectory instead of extracting inverse sixth power distance terms as an intermediate step in calculating NOEs. This is particularly important for molecules that sample conformational states on a timescale similar to molecular reorientation. The package is tested on sucrose and results are shown to differ in small but significant ways from those calculated using an inverse sixth power assumption. Results are also compared to experiment and found to be in reasonable agreement despite an expected underestimation of water viscosity by the water model selected. Copyright © 2016 Elsevier Inc. All rights reserved.

Large critical current densities and pinning forces in CSD-grown superconducting GdBa2Cu3O7-x -BaHfO3 nanocomposite films

NASA Astrophysics Data System (ADS)

Cayado, Pablo; Erbe, Manuela; Kauffmann-Weiss, Sandra; Bühler, Carl; Jung, Alexandra; Hänisch, Jens; Holzapfel, Bernhard

2017-09-01

GdBa2Cu3O7-x -BaHfO3 (GdBCO-BHO) nanocomposite (NC) films containing 12 mol% BHO nanoparticles were prepared by chemical solution deposition (CSD) following the TFA route on SrTiO3 (STO) single crystals and buffered metallic tapes supplied by two different companies: Deutsche Nanoschicht GmbH and SuperOx. We optimized the preparation of our GdBCO-BHO solutions with acetylacetone making the film synthesis very robust and reproducible, and obtained 220 nm films with excellent superconducting properties. We show the structural, morphological and superconducting properties of the films after a careful optimization of the processing parameters (growth temperature, oxygen partial pressure and heating ramp). The films reach critical temperatures (T c) of ˜94 K, self-field critical current densities (J c) of >7 MA cm- 2 and maximum pinning force densities (F p) of ˜16 GN m- 3 at 77 K on STO and T c of ˜94.5 K and J c > 1.5 MA cm- 2 on buffered metallic tapes. The transport properties under applied magnetic fields are significantly improved with respect to the pristine GdBCO films. The GdBCO-BHO NC films on STO present epitaxial c-axis orientation with excellent out-of-plane and in-plane texture. The films are, in general, very dense with a low amount of pores and only superficial indentations. On the other hand, we present, for the first time, a systematic study of CSD-grown GdBCO-BHO NC films on buffered metallic tapes. We have used the optimized growth conditions for STO as a reference and identified some limitations on the film synthesis that should be overcome for further improvement of the films’ superconducting properties.

New insights into the application of the valence rules in Zintl phases—Crystal and electronic structures of Ba{sub 7}Ga{sub 4}P{sub 9}, Ba{sub 7}Ga{sub 4}As{sub 9}, Ba{sub 7}Al{sub 4}Sb{sub 9}, Ba{sub 6}CaAl{sub 4}Sb{sub 9}, and Ba{sub 6}CaGa{sub 4}Sb{sub 9}

DOE Office of Scientific and Technical Information (OSTI.GOV)

He, Hua; Stoyko, Stanislav; Bobev, Svilen, E-mail: bobev@udel.edu

Crystals of three new ternary pnictides—Ba{sub 7}Al{sub 4}Sb{sub 9}, Ba{sub 7}Ga{sub 4}P{sub 9}, and Ba{sub 7}Ga{sub 4}As{sub 9} have been prepared by reactions of the respective elements in molten Al or Pb fluxes. Single-crystal X-ray diffraction studies reveal that the three phases are isotypic, crystallizing in the orthorhombic Ba{sub 7}Ga{sub 4}Sb{sub 9}-type structure (space group Pmmn, Pearson symbol oP40, Z=2), for which only the prototype is known. The structure is based on TrPn{sub 4} tetrahedra (Tr=Al, Ga; Pn=P, As, Sb), connected in an intricate scheme into 1D-ribbons. Long interchain Pn–Pn bonds (d{sub P–P}>3.0 Å; d{sub As–As}>3.1 Å; d{sub Sb–Sb}>3.3 Å)more » account for the realization of 2D-layers, separated by Ba{sup 2+} cations. Applying the classic valance rules to rationalize the bonding apparently fails, and Ba{sub 7}Ga{sub 4}Sb{sub 9} has long been known as a metallic Zintl phase. Earlier theoretical calculations, both empirical and ab-initio, suggest that the possible metallic properties originate from filled anti-bonding Pn–Pn states, and the special roles of the “cations” in this crystal structure. To experimentally probe this hypothesis, we sought to synthesize the ordered quaternary phases Ba{sub 6}CaTr{sub 4}Sb{sub 9} (Tr=Al, Ga). Single-crystal X-ray diffraction work confirms Ba{sub 6.145(3)}Ca{sub 0.855}Al{sub 4}Sb{sub 9} and Ba{sub 6.235(3)}Ca{sub 0.765}Ga{sub 4}Sb{sub 9}, with Ca atoms preferably substituting Ba on one of the three available sites. The nuances of the five crystal structures are discussed, and the chemical bonding in Ba{sub 7}Ga{sub 4}As{sub 9} is interrogated by tight-binding linear muffin-tin orbital calculations. - Graphical abstract: The new Zintl phases—Ba{sub 7}Al{sub 4}Sb{sub 9}, Ba{sub 7}Ga{sub 4}P{sub 9}, and Ba{sub 7}Ga{sub 4}As{sub 9}, and their quaternary variants Ba{sub 6}CaTr{sub 4}Sb{sub 9} (Tr=Al, Ga)—crystallize in the Ba{sub 7}Ga{sub 4}Sb{sub 9} structure type. The structures

77 FR 29692 - Segun M. Rasaki, M.D.; Decision and Order

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-18

... DEPARTMENT OF JUSTICE Drug Enforcement Administration [Docket No. 12-28] Segun M. Rasaki, M.D...'s action at which he may ultimately prevail.'' Kamal Tiwari, M.D., 76 FR 71604, 71606 (2011); see....100(b), I order that DEA Certificate of Registration BR9738595, issued to Segun M. Rasaki, M.D., be...

76 FR 51412 - Joe C. Fermo, M.D.; Revocation of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-18

... DEPARTMENT OF JUSTICE Drug Enforcement Administration Joe C. Fermo, M.D.; Revocation of... Enforcement Administration, issued an Order to Show Cause to Joe C. Fermo, M.D. (Registrant), of Tulsa... Order at 1 (citing 21 U.S.C. 823(f) and 824(a)(4)). The Show Cause Order specifically alleged that on...

Electronic structure of BaO/W cathode surfaces

NASA Technical Reports Server (NTRS)

Muller, Wolfgang

1989-01-01

The local electronic structure of the emissive layer of barium dispenser thermionic cathodes is investigated theoretically using the relativistic scattered-wave approach. The interaction of Ba and O with W, Os, and W-Os alloy surfaces is studied with atomic clusters modeling different absorption environments representative of B- and M-type cathodes. Ba is found to be strongly oxidized, while O and the metal substrate are in a reduced chemical state. The presence of O enhances the surface dipole and Ba binding energy relative to Ba on W. Model results for W-Os alloy substrates show only relatively small changes in Ba and O for identical geometries, but very large charge redistributions inside the substrate, which are attributed to the electronegativity difference between Os and W. If Os is present in the surface layer, the charge transfer from Ba to the substrate and the Ba binding energy increase relative to W. Explanations are offered for the improved electron emission from alloy surfaces and the different emission enhancement for different alloy substrates.

Tailoring Ba3Ca1.18Nb1.82O9-δ with NiO as electrolyte for proton-conducting solid oxide fuel cells

NASA Astrophysics Data System (ADS)

Zhu, Zhiwen; Guo, Enyan; Wei, Zhaoling; Wang, Huiqiang

2018-01-01

A strategy of tailoring Ba3Ca1.18Nb1.82O9-δ (BCN) is proposed, aiming to improve the sinterability and conductivity of BCN material for fuel cell applications. The new Ba3Ca1.18Nb1.77Ni0.05O9-δ (BCNNi) material shows a significant improvement in sinterability compared with BCN, leading to a high densification for BCNNi after sintering at as low as 1400 °C. In addition, the BCNNi exhibits a conductivity of 4.59 × 10-3 S cm-1 at 700 °C that is not only higher than that for BCN which only reaches 3.45 × 10-3 S cm-1 at the same temperature but also shows a significant improvement compared with that for BCN-based materials in literature reports. As a result, the cell with the BCNNi electrolyte shows a peak power density of 84 mW cm-2 at 700 °C which is also one of the largest ever reported for this type of cells. Further electrochemical studies indicate that the high conductivity of BCNNi electrolyte membrane benefits the fuel cell performance.

Transport properties of ultrathin BaFe1.84Co0.16As2 superconducting nanowires

NASA Astrophysics Data System (ADS)

Yuan, Pusheng; Xu, Zhongtang; Li, Chen; Quan, Baogang; Li, Junjie; Gu, Changzhi; Ma, Yanwei

2018-07-01

Superconducting nanowire single-photon detectors (SNSPDs) have an absolute advantage over other types of single-photon detectors, except for the low operating temperature. Therefore, much effort has been devoted to finding high-temperature superconducting materials that are suitable for preparing SNSPDs. Copper-based and MgB2 ultrathin superconducting nanowires have already been reported. However, the transport properties of iron-based ultrathin superconducting nanowires have not been studied. In this work, a 10 nm thick × 200 nm wide × 30 μm long high-quality superconducting nanowire was fabricated from ultrathin BaFe1.84Co0.16As2 films by a lift-off process. The precursor BaFe1.84Co0.16As2 film with a thickness of 10 nm and root-mean-square roughness of 1 nm was grown on CaF2 substrates by pulsed laser deposition. The nanowire shows a high superconducting critical temperature {T}{{c}}{{zero}} = 20 K with a narrow transition width of ΔT = 2.5 K and exhibits a high critical current density J c of 1.8 × 107 A cm-2 at 10 K. These results of ultrathin BaFe1.84Co0.16As2 nanowire will attract interest in electronic applications, including SNSPDs.

The effects of BaSO₄ loading on OPC cementing system for encapsulation of BaSO₄ scale from oil and gas industry.

PubMed

Hussein, O; Utton, C; Ojovan, M; Kinoshita, H

2013-10-15

The BaSO4 scales obtained from piping decontamination from oil and gas industries are most often classified as low level radioactive waste. These wastes could be immobilised by stable cement matrix to provide higher safety of handling, transportation, storage and disposal. However, the information available for the effects of the basic formulation such as waste loading on the fundamental properties is still limited. The present study investigated the effect of BaSO4 loading and water content on the properties of OPC-BaSO4 systems containing fine BaSO4 powder and coarse granules. The BaSO4 with different particle size had a marked effect on the compressive strength due to their different effects on hydration products formed. Introduction of fine BaSO4 powder resulted in an increased formation of CaCO3 in the system, which significantly contributed to the compressive strength of the products. Amount of water was important to control the CaCO3 formation, and water to cement ratio of 0.53 was found to be a good level to maintain a low porosity of the products both for fine BaSO4 powder and coarse BaSO4 granule. BaSO4 loading of up to 60 wt% has been achieved satisfying the minimum compressive strength of 5 MPa required for the radioactive wasteforms. Copyright © 2013 Elsevier B.V. All rights reserved.

133 Ba+: a new ion qubit

NASA Astrophysics Data System (ADS)

Christensen, Justin; Hucul, David; Campbell, Wesley; Hudson, Eric

2017-04-01

133 Ba+ combines many of the advantages of commonly used trapped ion qubits. 133Ba+ has a nuclear spin 1/2, allowing for a robust hyperfine qubit with simple state preparation and readout. The existence of long-lived metastable D-states and a lack of low-lying F-states simplifies shelving, which will allow high fidelity state detection. The visible wavelength optical transitions enable the use of high-power lasers, low-loss fibers, high quantum efficiency detectors, and other optical technologies developed for visible wavelength light. Furthermore, background-free qubit readout, where the readout is insensitive to laser scatter, is possible in 133Ba+, and simplifies its use in small ion traps and the study of ions near surfaces. We report progress on realizing this qubit. We load barium ions into an ion trap using thermal ionization from a platinum ribbon. We experimentally demonstrate the isotopic purification of large numbers of barium ions using laser heating and cooling along with mass filtering to produce isotopically pure chains of any naturally-occurring barium isotope. This purification process has allowed us to laser cool rare, naturally-occurring barium isotopes 132Ba+and130Ba+, and we report the isotope shifts from 138Ba+ of the P1/2 to D3/2 transitions near 650 nm for the first time. In addition, we have developed an ion gun to produce high luminosity ion beams with adjustable mean kinetic energy by combining a surface ionization source and ion optics.

Effect of calcination temperature on microstructure, dielectric, magnetic and optical properties of Ba0.7La0.3Fe11.7Co0.3O19 hexaferrites

NASA Astrophysics Data System (ADS)

Kaur, Talwinder; Kaur, Barjinder; Bhat, Bilal H.; Kumar, Sachin; Srivastava, A. K.

2015-01-01

M-type barium hexaferrite Ba0.7La0.3Fe11.7Co0.3O19 (BaLCM) powder, synthesized using sol gel auto combustion method, heat treated at 700, 900, 1100 and 1200 °C. X ray diffraction (XRD) powder patterns of heat treated samples show the formation of pure phase of M-type hexaferrite after 700 °C. Thermo gravimetric analysis (TGA) reveals that the weight loss of BaLCM becomes constant after 680 °C. The presence of two prominent peaks, at 432 cm-1 and 586 cm-1 in Fourier Transform Infrared Spectroscopy (FT-IR) spectra, gives the idea of formation of M-type hexaferrites. The M-H curve obtained from Vibrating Sample Magnetometer (VSM) were used to calculate saturation magnetization (MS), retentivity (Mr), squareness ration (SR) and coercivity (Hc). The maximum value of coercivity (5602 Oe) is found at 900 °C. The band gap dependency on temperature was studied using UV-vis NIR spectroscopy. The dielectric constant has been found to be high at low frequency but it decreases with increase in frequency. Such kind of dielectric behavior is explained on the basis of Koop's phenomenological theory and Maxwell Wagner theory.

RadNet Air Data From Baltimore, MD

EPA Pesticide Factsheets

This page presents radiation air monitoring and air filter analysis data for Baltimore, MD from EPA's RadNet system. RadNet is a nationwide network of monitoring stations that measure radiation in air, drinking water and precipitation.

Ubiquitination-Related MdBT Scaffold Proteins Target a bHLH Transcription Factor for Iron Homeostasis1[OPEN

PubMed Central

Zhao, Qiang; Wang, Qing-Jie; Wang, Xiao-Fei; You, Chun-Xiang

2016-01-01

Iron (Fe) homeostasis is crucial for plant growth and development. A network of basic helix-loop-helix (bHLH) transcription factors positively regulates Fe uptake during iron deficiency. However, their up-regulation or overexpression leads to Fe overload and reactive oxygen species generation, thereby damaging the plants. Here, we found that two BTB/TAZ proteins, MdBT1 and MdBT2, interact with the MbHLH104 protein in apple. In addition, the function of MdBT2 was characterized as a regulator of MdbHLH104 degradation via ubiquitination and the 26S proteasome pathway, thereby controlling the activity of plasma membrane H+-ATPases and the acquisition of iron. Furthermore, MdBT2 interacted with MdCUL3 proteins, which were required for the MdBT2-mediated ubiquitination modification of MdbHLH104 and its degradation. In sum, our findings demonstrate that MdBT proteins interact with MdCUL3 to bridge the formation of the MdBTsMdCUL3 complex, which negatively modulates the degradation of the MdbHLH104 protein in response to changes in Fe status to maintain iron homeostasis in plants. PMID:27660166

Enhanced electron mobility at the two-dimensional metallic surface of BaSnO3 electric-double-layer transistor at low temperatures

NASA Astrophysics Data System (ADS)

Fujiwara, Kohei; Nishihara, Kazuki; Shiogai, Junichi; Tsukazaki, Atsushi

2017-05-01

Wide-bandgap oxides exhibiting high electron mobility hold promise for the development of useful electronic and optoelectronic devices as well as for basic research on two-dimensional electron transport phenomena. A perovskite-type tin oxide, BaSnO3, is currently one of such targets owing to distinctly high mobility at room temperature. The challenge to overcome towards the use of BaSnO3 thin films in applications is suppression of dislocation scattering, which is one of the dominant scattering origins for electron transport. Here, we show that the mobility of the BaSnO3 electric-double-layer transistor reaches 300 cm2 V-1 s-1 at 50 K. The improved mobility indicates that charged dislocation scattering is effectively screened by electrostatically doped high-density charge carriers. We also observed metallic conduction persisting down to 2 K, which is attributed to the transition to the degenerate semiconductor. The experimental verification of bulk-level mobility at the densely accumulated surface sheds more light on the importance of suppression of dislocation scattering by interface engineering in doped BaSnO3 thin films for transparent electrode applications.

Validity of the Medical College Admission Test for Predicting MD-PhD Student Outcomes

ERIC Educational Resources Information Center

Bills, James L.; VanHouten, Jacob; Grundy, Michelle M.; Chalkley, Roger; Dermody, Terence S.

2016-01-01

The Medical College Admission Test (MCAT) is a quantitative metric used by MD and MD-PhD programs to evaluate applicants for admission. This study assessed the validity of the MCAT in predicting training performance measures and career outcomes for MD-PhD students at a single institution. The study population consisted of 153 graduates of the…

The bZIP transcription factor MdHY5 regulates anthocyanin accumulation and nitrate assimilation in apple.

PubMed

An, Jian-Ping; Qu, Feng-Jia; Yao, Ji-Fang; Wang, Xiao-Na; You, Chun-Xiang; Wang, Xiao-Fei; Hao, Yu-Jin

2017-01-01

The basic leucine zipper (bZIP) transcription factor HY5 plays a multifaceted role in plant growth and development. Here the apple MdHY5 gene was cloned based on its homology with Arabidopsis HY5 . Expression analysis demonstrated that MdHY5 transcription was induced by light and abscisic acid treatments. Electrophoretic mobility shift assays and transient expression assays subsequently showed that MdHY5 positively regulated both its own transcription and that of MdMYB10 by binding to E-box and G-box motifs, respectively. Furthermore, we obtained transgenic apple calli that overexpressed the MdHY5 gene, and apple calli coloration assays showed that MdHY5 promoted anthocyanin accumulation by regulating expression of the MdMYB10 gene and downstream anthocyanin biosynthesis genes. In addition, the transcript levels of a series of nitrate reductase genes and nitrate uptake genes in both wild-type and transgenic apple calli were detected. In association with increased nitrate reductase activities and nitrate contents, the results indicated that MdHY5 might be an important regulator in nutrient assimilation. Taken together, these results indicate that MdHY5 plays a vital role in anthocyanin accumulation and nitrate assimilation in apple.

Substantial enhancement of energy storage capability in polymer nanocomposites by encapsulation of BaTiO3 NWs with variable shell thickness.

PubMed

Wang, Guanyao; Huang, Yanhui; Wang, Yuxin; Jiang, Pingkai; Huang, Xingyi

2017-08-09

Dielectric polymer nanocomposites have received keen interest due to their potential application in energy storage. Nevertheless, the large contrast in dielectric constant between the polymer and nanofillers usually results in a significant decrease of breakdown strength of the nanocomposites, which is unfavorable for enhancing energy storage capability. Herein, BaTiO 3 nanowires (NWs) encapsulated by TiO 2 shells of variable thickness were utilized to fabricate dielectric polymer nanocomposites. Compared with nanocomposites with bare BaTiO 3 NWs, significantly enhanced energy storage capability was achieved for nanocomposites with TiO 2 encapsulated BaTiO 3 NWs. For instance, an ultrahigh energy density of 9.53 J cm -3 at 440 MV m -1 could be obtained for nanocomposites comprising core-shell structured nanowires, much higher than that of nanocomposites with 5 wt% raw ones (5.60 J cm -3 at 360 MV m -1 ). The discharged energy density of the proposed nanocomposites with 5 wt% mTiO 2 @BaTiO 3 -1 NWs at 440 MV m -1 seems to rival or exceed those of some previously reported nanocomposites (mostly comprising core-shell structured nanofillers). More notably, this study revealed that the energy storage capability of the nanocomposites can be tailored by the TiO 2 shell thickness. Finite element simulations were employed to analyze the electric field distribution in the nanocomposites. The enhanced energy storage capability should be mainly attributed to the smoother gradient of dielectric constant between the nanofillers and polymer matrix, which alleviated the electric field concentration and leakage current in the polymer matrix. The methods and results herein offer a feasible approach to construct high-energy-density polymer nanocomposites with core-shell structured nanowires.

77 FR 8877 - ICD-9-CM Coordination and Maintenance (C&M) Committee Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-15

... Coordination and Maintenance (C&M) Committee Meeting National Center for Health Statistics (NCHS... Coordination and Maintenance (C&M) Committee meeting. Time and Date: 9 a.m.-5:30 p.m., March 5, 2012. Place... entering the building. Attendees who wish to attend the ICD- 9-CM C&M meeting on March 5, 2012, must submit...

Formation of metal nanoparticles in MgF2, CaF2 and BaF2 crystals under the electron beam irradiation

NASA Astrophysics Data System (ADS)

Bochkareva, Elizaveta S.; Sidorov, Alexander I.; Yurina, Uliana V.; Podsvirov, Oleg A.

2017-07-01

It is shown experimentally that electron beam action with electrons energies of 50 and 70 keV on MgF2, CaF2 and BaF2 crystals results in local formation in the crystal near-surface layer of Mg, Ca or Ba nanoparticles which possess plasmon resonance. In the case of MgF2 spheroidal nanoparticles are formed, in the cases of CaF2 and BaF2 - spherical. The formation of metal nanoparticles is confirmed by computer simulation in dipole quasistatic approximation. The dependence of absorption via electron irradiation dose is non-linear. It is caused by the increase of nanoparticles concentration and by the increase of nanoparticles sizes during irradiation. In the irradiated zones of MgF2 crystals, for irradiation doses less than 80 mC/cm2, the intense luminescence in a visible range appears. The practical application of fabricated composite materials for multilevel optical information recording is discussed.

PuReMD-GPU: A reactive molecular dynamics simulation package for GPUs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kylasa, S.B., E-mail: skylasa@purdue.edu; Aktulga, H.M., E-mail: hmaktulga@lbl.gov; Grama, A.Y., E-mail: ayg@cs.purdue.edu

2014-09-01

We present an efficient and highly accurate GP-GPU implementation of our community code, PuReMD, for reactive molecular dynamics simulations using the ReaxFF force field. PuReMD and its incorporation into LAMMPS (Reax/C) is used by a large number of research groups worldwide for simulating diverse systems ranging from biomembranes to explosives (RDX) at atomistic level of detail. The sub-femtosecond time-steps associated with ReaxFF strongly motivate significant improvements to per-timestep simulation time through effective use of GPUs. This paper presents, in detail, the design and implementation of PuReMD-GPU, which enables ReaxFF simulations on GPUs, as well as various performance optimization techniques wemore » developed to obtain high performance on state-of-the-art hardware. Comprehensive experiments on model systems (bulk water and amorphous silica) are presented to quantify the performance improvements achieved by PuReMD-GPU and to verify its accuracy. In particular, our experiments show up to 16× improvement in runtime compared to our highly optimized CPU-only single-core ReaxFF implementation. PuReMD-GPU is a unique production code, and is currently available on request from the authors.« less

39. SAME VIEW AS MD6A38, ONLY WITH A HORIZONTAL ORIENTATION. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

39. SAME VIEW AS MD-6A-38, ONLY WITH A HORIZONTAL ORIENTATION. - Baltimore & Ohio Railroad, Mount Clare Shops, South side of Pratt Street between Carey & Poppleton Streets, Baltimore, Independent City, MD

RysannMD: A biomedical semantic annotator balancing speed and accuracy.

PubMed

Cuzzola, John; Jovanović, Jelena; Bagheri, Ebrahim

2017-07-01

Recently, both researchers and practitioners have explored the possibility of semantically annotating large and continuously evolving collections of biomedical texts such as research papers, medical reports, and physician notes in order to enable their efficient and effective management and use in clinical practice or research laboratories. Such annotations can be automatically generated by biomedical semantic annotators - tools that are specifically designed for detecting and disambiguating biomedical concepts mentioned in text. The biomedical community has already presented several solid automated semantic annotators. However, the existing tools are either strong in their disambiguation capacity, i.e., the ability to identify the correct biomedical concept for a given piece of text among several candidate concepts, or they excel in their processing time, i.e., work very efficiently, but none of the semantic annotation tools reported in the literature has both of these qualities. In this paper, we present RysannMD (Ryerson Semantic Annotator for Medical Domain), a biomedical semantic annotation tool that strikes a balance between processing time and performance while disambiguating biomedical terms. In other words, RysannMD provides reasonable disambiguation performance when choosing the right sense for a biomedical term in a given context, and does that in a reasonable time. To examine how RysannMD stands with respect to the state of the art biomedical semantic annotators, we have conducted a series of experiments using standard benchmarking corpora, including both gold and silver standards, and four modern biomedical semantic annotators, namely cTAKES, MetaMap, NOBLE Coder, and Neji. The annotators were compared with respect to the quality of the produced annotations measured against gold and silver standards using precision, recall, and F 1 measure and speed, i.e., processing time. In the experiments, RysannMD achieved the best median F 1 measure across the

MdHY5 positively regulates cold tolerance via CBF-dependent and CBF-independent pathways in apple.

PubMed

An, Jian-Ping; Yao, Ji-Fang; Wang, Xiao-Na; You, Chun-Xiang; Wang, Xiao-Fei; Hao, Yu-Jin

2017-11-01

Cold stress is a major external stimulator that affects crop quality and productivity. The CBF cold regulatory pathway has been regarded as a master regulator in the response to cold stress. In this study, we found that the apple bZIP transcription factor, MdHY5, was responsive to cold treatment both at the transcriptional and at the post-translational levels. Moreover, overexpression of MdHY5 enhanced cold tolerance in apple calli and Arabidopsis. Subsequently, EMSA assay and transient expression assay demonstrated that MdHY5 positively regulated the transcript of MdCBF1 by binding to G-Box motif of its promoter. Furthermore, MdHY5 also regulated the expression of CBF-independent cold-regulated genes. Taken together, our data suggest that MdHY5 positively modulates plant cold tolerance through CBF-dependent and CBF-independent pathways, providing a deeper understanding of MdHY5-regulated cold tolerance in apple. Copyright © 2017 Elsevier GmbH. All rights reserved.

Dielectric maximum temperature non-monotonic behavior in unaxial Sr0.75Ba0.25Nb2O6 relaxor seen via acoustic emission

NASA Astrophysics Data System (ADS)

Dul'kin, E.; Kojima, S.; Roth, M.

2011-08-01

[100] oriented Sr0.75Ba0.25Nb2O6 relaxor crystals have been studied by means of acoustic emission (AE) over a wide 20-400 °C temperature range. Both the Burns temperature, Td = 350 °C, and the intermediate temperature, T* = 183°C, and the susceptibility maximum temperature, Tm (59 °C on heating and 47 °C on cooling), have been successfully detected. Dependent upon the external electric field, the Tm exhibits a local minimum near 0.25 kV/cm accompanied by pronounced AE maximum in a manner which had recently been detected in Pb(Mg1/3Nb2/3)O3-0.33PbTiO3 by Dul'kin et al. [Appl. Phys. Lett. 94, 252904 (2009)] and in Pb(Sc1/2Ta1/2)O3 by Dul'kin et al. [Phys. Rev. B 82, 180101(R) (2010)], whereas the T* increases monotonically, similar to that which had recently been revealed in BaTiO3 by Dul'kin et al. [Appl. Phys. Lett. 97, 032903 (2010)] with a rate of 7.5 K cm/kV. An observed Tm behavior is discussed from the point of view of the existence of the random electric field components along the [100] direction in Sr0.75Ba0.25Nb2O6 crystals.

Dynamics of photoexcited Ba+ cations in 4He nanodroplets

NASA Astrophysics Data System (ADS)

Leal, Antonio; Zhang, Xiaohang; Barranco, Manuel; Cargnoni, Fausto; Hernando, Alberto; Mateo, David; Mella, Massimo; Drabbels, Marcel; Pi, Martí

2016-03-01

We present a joint experimental and theoretical study on the desolvation of Ba+ cations in 4He nanodroplets excited via the 6p ← 6s transition. The experiments reveal an efficient desolvation process yielding mainly bare Ba+ cations and Ba+Hen exciplexes with n = 1 and 2. The speed distributions of the ions are well described by Maxwell-Boltzmann distributions with temperatures ranging from 60 to 178 K depending on the excitation frequency and Ba+ Hen exciplex size. These results have been analyzed by calculations based on a time-dependent density functional description for the helium droplet combined with classical dynamics for the Ba+. In agreement with experiment, the calculations reveal the dynamical formation of exciplexes following excitation of the Ba+ cation. In contrast to experimental observation, the calculations do not reveal desolvation of excited Ba+ cations or exciplexes, even when relaxation pathways to lower lying states are included.

MD-2 is required for disulfide HMGB1–dependent TLR4 signaling

PubMed Central

Wang, Haichao; Ju, Zhongliang; Ragab, Ahmed A.; Lundbäck, Peter; Long, Wei; Valdes-Ferrer, Sergio I.; He, Mingzhu; Pribis, John P.; Li, Jianhua; Lu, Ben; Gero, Domokos; Szabo, Csaba; Antoine, Daniel J.; Harris, Helena E.; Golenbock, Doug T.; Meng, Jianmin; Roth, Jesse; Chavan, Sangeeta S.; Andersson, Ulf; Billiar, Timothy R.; Al-Abed, Yousef

2015-01-01

Innate immune receptors for pathogen- and damage-associated molecular patterns (PAMPs and DAMPs) orchestrate inflammatory responses to infection and injury. Secreted by activated immune cells or passively released by damaged cells, HMGB1 is subjected to redox modification that distinctly influences its extracellular functions. Previously, it was unknown how the TLR4 signalosome distinguished between HMGB1 isoforms. Here we demonstrate that the extracellular TLR4 adaptor, myeloid differentiation factor 2 (MD-2), binds specifically to the cytokine-inducing disulfide isoform of HMGB1, to the exclusion of other isoforms. Using MD-2–deficient mice, as well as MD-2 silencing in macrophages, we show a requirement for HMGB1-dependent TLR4 signaling. By screening HMGB1 peptide libraries, we identified a tetramer (FSSE, designated P5779) as a specific MD-2 antagonist preventing MD-2–HMGB1 interaction and TLR4 signaling. P5779 does not interfere with lipopolysaccharide-induced cytokine/chemokine production, thus preserving PAMP-mediated TLR4–MD-2 responses. Furthermore, P5779 can protect mice against hepatic ischemia/reperfusion injury, chemical toxicity, and sepsis. These findings reveal a novel mechanism by which innate systems selectively recognize specific HMGB1 isoforms. The results may direct toward strategies aimed at attenuating DAMP-mediated inflammation while preserving antimicrobial immune responsiveness. PMID:25559892

Revisiting the BaO2/BaO redox cycle for solar thermochemical energy storage.

PubMed

Carrillo, A J; Sastre, D; Serrano, D P; Pizarro, P; Coronado, J M

2016-03-21

The barium peroxide-based redox cycle was proposed in the late 1970s as a thermochemical energy storage system. Since then, very little attention has been paid to such redox couples. In this paper, we have revisited the use of reduction-oxidation reactions of the BaO2/BaO system for thermochemical heat storage at high temperatures. Using thermogravimetric analysis, reduction and oxidation reactions were studied in order to find the main limitations associated with each process. Furthermore, the system was evaluated through several charge-discharge stages in order to analyse its possible degradation after repeated cycling. Through differential scanning calorimetry the heat stored and released were also determined. Oxidation reaction, which was found to be slower than reduction, was studied in more detail using isothermal tests. It was observed that the rate-controlling step of BaO oxidation follows zero-order kinetics, although at high temperatures a deviation from Arrhenius behaviour was observed probably due to hindrances to anionic oxygen diffusion caused by the formation of an external layer of BaO2. This redox couple was able to withstand several redox cycles without deactivation, showing reaction conversions close to 100% provided that impurities are previously eliminated through thermal pre-treatment, demonstrating the feasibility of this system for solar thermochemical heat storage.

A novel triazine ring compound (MD568) exerts in vivo and in vitro effects on lipid metabolism.

PubMed

Jia, Dan; Li, Ziwen; Gao, Ying; Feng, Yifan; Li, Weimin

2018-07-01

In this study, we investigated the toxicity and biological activity of a novel triazine ring compound named magnolol derivative 568 (MD568). The LD 50 of MD568 was determined in Sprague-Dawley (SD) rats by intraperitoneal injection. Treatment of high fat diet-induced obese rats with MD568 demonstrated that MD568 displayed significant anti-obesity effects. MD568 markedly reduced body weight, blood lipid contents, white adipose tissue (WAT) and liver mass in obese rats. In addition, MD568 modulated lesions in WAT through regulating PPAR-Ɣ, C/EBP-a, SREBP-1c and FABP-4 proteins in the liver through regulating PPAR-α, SREBP-1c and FABP-4. We also evaluated the effects of MD568 on the proliferation and differentiation of 3T3-L1 pre-adipocytes and investigated the underlying mechanism by microarray analysis. Results showed that MD568 has good inhibitory activity on lipogenesis and lipid accumulation in 3T3-L1 pre-adipocytes. The protein expression levels of the adipogenic transcription factors PPAR-Ɣ, C/EBP-a, SREBP-1c and FABP-4 were reduced by MD568. In addition, the gene expression of FAS and LDL was also significantly down-regulated by MD568. Microarray data enrichment analysis demonstrated that the underlying mechanism of action of MD568 may be related to its regulatory effects on genes associated with the biological processes or pathways in lipid metabolism. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

Sustainable water recovery from oily wastewater via forward osmosis-membrane distillation (FO-MD).

PubMed

Zhang, Sui; Wang, Peng; Fu, Xiuzhu; Chung, Tai-Shung

2014-04-01

This study proposed and investigated a hybrid forward osmosis - membrane distillation (FO-MD) system for sustainable water recovery from oily wastewater by employing lab-fabricated FO and MD hollow fiber membranes. Stable oil-in-water emulsions of different concentrations with small droplet sizes (<1 μm) were firstly prepared and applied as the feed solution in the FO process. Fouling was immediately observed in the FO mode and was low on the cellulose triacetate (CTA) - based thin film composite (TFC) membranes. Moreover, slight increment of fouling was observed in the first few hours and the water flux was then stabilized over 24 h. The characterizations of water flux and solute rejection in separate FO and MD processes revealed that a high water flux, good NaCl rejection, impressively high retention of oil droplets and partial permeation of acetic acid could be achieved. Finally, an integrated FO-MD system was developed to treat the oily wastewater containing petroleum, surfactant, NaCl and acetic acid at 60 °C in the batch mode. The water flux in FO undergoes three-stage decline due to fouling and reduction in osmotic driving force, but is quite stable in MD regardless of salt concentration. Oily wastewater with relatively high salinity could be effectively recovered by the FO-MD hybrid system while maintaining large water flux, at least 90% feed water recovery could be readily attained with only trace amounts of oil and salts, and the draw solution was re-generated for the next rounds of FO-MD run. Interestingly, significant amount of acetic acid was also retained in the permeate for further reuse as a chemical additive during the production of crude oil. The work has demonstrated that not only water but also organic additives in the wastewater could be effectively recovered by FO-MD systems for reuse or other utilizations. Copyright © 2014 Elsevier Ltd. All rights reserved.

InforMD: a new initiative to raise public awareness about breast density

PubMed Central

Hugo, Honor J; Zysk, Aneta; Dasari, Pallave; Britt, Kara; Hopper, John L; Stone, Jennifer; Thompson, Erik W; Ingman, Wendy V

2018-01-01

On a mammogram, breast density (also known as mammographic density) is shown as white and bright regions and is associated with reduced sensitivity in cancer detection and increased breast cancer risk. However, many Australian women are unaware of the significance of breast density as it is not routinely reported or discussed. In order to address this lack of knowledge, Australian breast cancer researchers with expertise in mammographic density formed the InforMD alliance (INformation FORum on Mammographic Density) in 2016. The alliance is working to raise awareness of breast density with the goal of improving breast cancer diagnosis and health outcomes for women. The InforMD website (www.InforMD.org.au) was launched in October 2016, coinciding with a major nationwide public awareness campaign by the alliance during breast cancer awareness month. The website contains unbiased, accurate, updated information on breast density. The website also provides summaries of major research articles in layperson language, recent news items related to breast density, links to relevant information for health professionals, events, and feature articles. Members of the public and health professionals can also subscribe for news updates. The interactive online Forum section facilitates discussion between health professionals, scientists and members of the public. To increase online traffic to the website, Facebook (www.facebook.com/BeInforMD) and Twitter (https://twitter.com/BeInforMD_) pages were launched in December 2016. Since its launch, InforMD has generated considerable interest. The public awareness campaign reached over 7 million Australians through a combination of newspaper, TV, radio, and online news. The website has attracted 13,058 unique visitors and 30,353 page views (data as of 19/12/2017). Breast cancer researchers have a significant role to play in disseminating information to the public on breast density. A combination of mainstream and social media, together with

InforMD: a new initiative to raise public awareness about breast density.

PubMed

Hugo, Honor J; Zysk, Aneta; Dasari, Pallave; Britt, Kara; Hopper, John L; Stone, Jennifer; Thompson, Erik W; Ingman, Wendy V

2018-01-01

On a mammogram, breast density (also known as mammographic density) is shown as white and bright regions and is associated with reduced sensitivity in cancer detection and increased breast cancer risk. However, many Australian women are unaware of the significance of breast density as it is not routinely reported or discussed. In order to address this lack of knowledge, Australian breast cancer researchers with expertise in mammographic density formed the InforMD alliance (INformation FORum on Mammographic Density) in 2016. The alliance is working to raise awareness of breast density with the goal of improving breast cancer diagnosis and health outcomes for women. The InforMD website (www.InforMD.org.au) was launched in October 2016, coinciding with a major nationwide public awareness campaign by the alliance during breast cancer awareness month. The website contains unbiased, accurate, updated information on breast density. The website also provides summaries of major research articles in layperson language, recent news items related to breast density, links to relevant information for health professionals, events, and feature articles. Members of the public and health professionals can also subscribe for news updates. The interactive online Forum section facilitates discussion between health professionals, scientists and members of the public. To increase online traffic to the website, Facebook (www.facebook.com/BeInforMD) and Twitter (https://twitter.com/BeInforMD_) pages were launched in December 2016. Since its launch, InforMD has generated considerable interest. The public awareness campaign reached over 7 million Australians through a combination of newspaper, TV, radio, and online news. The website has attracted 13,058 unique visitors and 30,353 page views (data as of 19/12/2017). Breast cancer researchers have a significant role to play in disseminating information to the public on breast density. A combination of mainstream and social media, together with

Structural properties of ultrafine Ba-hexaferrite nanoparticles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Makovec, Darko, E-mail: Darko.Makovec@ijs.si; Primc, Darinka; Sturm, Saso

2012-12-15

Crystal structure of ultrafine Ba-hexaferrite (BaFe{sub 12}O{sub 19}) nanoparticles was studied using X-ray diffractometry (XRD), high-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray spectroscopy (EDXS), X-ray absorption fine structure (XAFS), and Moessbauer spectroscopy (MS), to be compared to the structure of larger nanoparticles and the bulk. The nanoparticles were synthesized with hydrothermal treatment of an appropriate suspension of Ba and Fe hydroxides in the presence of a large excess of OH{sup -}. The ultrafine nanoparticles were formed in a discoid shape, {approx}10 nm wide and only {approx}3 nm thick, comparable to the size of the hexagonal unit cell in the c-direction.more » The HRTEM image analysis confirmed the hexaferrite structure, whereas EDXS showed the composition matching the BaFe{sub 12}O{sub 19} formula. XAFS and MS analyses showed considerable disorder of the structure, most probably responsible for the low magnetization. - Graphical abstract: Left: HREM image of an ultrafine Ba-hexaferrite nanoparticle (inset: TEM image of the nanoparticles); Right: the experimental HRTEM image is compared with calculated image and corresponding atomic model. Highlights: Black-Right-Pointing-Pointer Crystal structure of ultrafine Ba-hexaferrite (BaFe{sub 12}O{sub 19}) nanoparticles was compared to the structure of the bulk. Black-Right-Pointing-Pointer Thickness the discoid nanoparticles was comparable to the size of the hexagonal unit cell in the c-direction. Black-Right-Pointing-Pointer Considerable disorder of the nanoparticles' structure is most probably responsible for their low magnetization.« less

An apple B-box protein, MdCOL11, is involved in UV-B- and temperature-induced anthocyanin biosynthesis.

PubMed

Bai, Songling; Saito, Takanori; Honda, Chikako; Hatsuyama, Yoshimichi; Ito, Akiko; Moriguchi, Takaya

2014-11-01

Our studies showed that an apple B-box protein, MdCOL11, the homolog of AtBBX22, is involved in UV-B- and temperature-induced anthocyanin biosynthesis in apple peel. Anthocyanin is responsible for the red pigmentation in apple peel and a R2R3 MYB gene, MdMYBA/1/10, a homolog of MdMYBA, controls its accumulation. Arabidopsis PAP1 is under the control of a series of upstream factors involved in light signal transduction and photomorphogenesis, such as ELONGATED HYPOCOTYL 5 (HY5) and B-box family (BBX) proteins. In this study, we identified and characterized the homolog of Arabidopsis BBX22 in apple, designated as MdCOL11. Overexpression of MdCOL11 in Arabidopsis enhanced the accumulation of anthocyanin. In apples, MdCOL11 was differentially expressed in all tissues, with the highest expression in petals and the lowest expression in the xylem. Transcripts of MdCOL11 noticeably accumulated at the ripening stage, concomitant with increases in the expressions of anthocyanin biosynthesis-related genes. In an in vitro treatment experiment, MdCOL11 was upregulated in an ultra-violet (UV)-B- and temperature-dependent manner, together with the inductions of anthocyanin biosynthesis-related genes and anthocyanin accumulation in apple peel. Furthermore, a dual-luciferase assay indicated that (1) MdCOL11 regulated the expression of MdMYBA and (2) MdCOL11 was a target of MdHY5. Taken together, our results suggest that MdCOL11 is involved in MdHY5-mediated signal transduction and regulates anthocyanin accumulation in apple peel, which sheds new light on anthocyanin accumulation in apples.

(Ba+Sr)/Ti ratio dependence of the dielectric properties for (Ba0.5Sr0.5)TiO3 thin films prepared by ion beam sputtering

NASA Astrophysics Data System (ADS)

Yamamichi, Shintaro; Yabuta, Hisato; Sakuma, Toshiyuki; Miyasaka, Yoichi

1994-03-01

(Ba0.5Sr0.5)TiO3 thin films were prepared by ion beam sputtering from powder targets with (Ba+Sr)/Ti ratios ranging from 0.80 to 1.50. All of the perovskite (Ba,Sr)TiO3 films were single phase except for the film with a (Ba+Sr)/Ti ratio of 1.41. The dielectric constant values notably depended on the (Ba+Sr)/Ti ratio for films thicker than 70 nm. The highest dielectric constant of 580 was achieved for the 5% (Ba+Sr) rich film. This (Ba+Sr)/Ti ratio dependence was diminished by the thickness dependence for thinner films. The grain sizes for the 9% (Ba+Sr) rich film and for the 6% (Ba+Sr) poor film ranged from 70 to 100 nm and from 30 to 60 nm, respectively. This grain size difference could explain why slightly A-site rich (Ba,Sr)TiO3 films have a larger dielectric constant than A-site poor films.

Thin films sputtered from Ba{sub 2}NdFeNb{sub 4}O{sub 15} multiferroic targets on BaFe{sub 12}O{sub 19} coated substrates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bodeux, Romain; Univ. Bordeaux, ICMCB, UPR 9048, F-33600 Pessac; Michau, Dominique, E-mail: dominique.michau@icmcb.cnrs.fr

2016-09-15

Highlights: • Synthesis of Ba{sub 2}NdFeNb{sub 4}O{sub 15}/BaFe{sub 12}O{sub 19} (BaM) heterostructures by RF magnetron sputtering. • Growth of TTB layer were retained regardless of the underlayer (Pt bottom electrode or BaM). • Dielectric and magnetic properties were obtained from the Pt/TTB/BaM/Pt stacks. - Abstract: Ba{sub 2}NdFeNb{sub 4}O{sub 15} tetragonal tungsten bronze (TTB)/BaFe{sub 12}O{sub 19} (BaM) hexaferrite bilayers have been grown by RF magnetron sputtering on Pt/TiO{sub 2}/SiO{sub 2}/Si (PtS) substrates. The BaM layer is textured along (0 0 1) while the TTB layer is multioriented regardless of the PtS or BaM/PtS substrate. Dielectric properties of TTB films are similarmore » to those of bulk, i.e., ε ∼ 150 and a magnetic hysteresis loop is obtained from TTB/BaM bilayers, thanks to the BaM component. This demonstrates the possibility of transferring to 2 dimensional structures the composite multiferroic system TTB/BaM previously identified in 3 dimensional bulk ceramics.« less

Beta-gamma spectroscopy of the neutron-rich 150Ba

NASA Astrophysics Data System (ADS)

Yokoyama, R.; Ideguchi, E.; Simpson, G. S.; Tanaka, Mn; Nishimura, S.; Doornenbal, P.; Lorusso, G.; Söderström, P.-A.; Sumikama, T.; Wu, J.; Xu, Z. Y.; Aoi, N.; Baba, H.; Bello Garrote, F. L.; Benzoni, G.; Browne, F.; Daido, R.; Fang, Y.; Fukuda, N.; Gottardo, A.; Gey, G.; Go, S.; Inabe, N.; Isobe, T.; Kameda, D.; Kobayashi, K.; Kobayashi, M.; Kojouharov, I.; Komatsubara, T.; Kubo, T.; Kurz, N.; Kuti, I.; Li, Z.; Matsushita, M.; Michimasa, S.; Moon, C. B.; Nishibata, H.; Nishizuka, I.; Odahara, A.; Patel, Z.; Rice, S.; Sahin, E.; Sakurai, H.; Schaffner, H.; Sinclair, L.; Suzuki, H.; Takeda, H.; Taprogge, J.; Vajta, Zs; Watanabe, H.; Yagi, A.; Inakura, T.

2018-04-01

Excited states in the neutron-rich nucleus ^{150}Ba have been observed via β-γ spectroscopy at the Radioactive Isotope Beam Factory, RIKEN Nishina Center. The ^{150}Ba ions were produced by the in-flight fission of a ^{238}U beam with an energy of 345 MeV/nucleon. The E(2+) energy of ^{150}Ba was identified at 100 keV, which is the lowest known in the neutron-rich Ba isotopes. A γ-ray peak was also observed at 597 keV. A mean-field calculation with a fully 3D real space was performed and a static octupole deformation was obtained for the Ba isotopes. K^{π}=0- and 1- excited states with significant octupole collectivity were newly predicted at around or lower than 1 MeV on the ground state of ^{150}Ba by a random-phase approximation calculation. The 597 keV γ ray can be interpreted as a negative-parity state, showing that ^{150}Ba may possess octupole collectivity.

Ba{sub 3}GeS{sub 5} and Ba{sub 3}InS{sub 4}Cl: Interesting size effects originated from the tetrahedral anions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pan, Ming-Yan; Xia, Sheng-Qing, E-mail: shqxia@sdu.edu.cn; Liu, Xiao-Cun

2014-11-15

Two new barium chalcogenides, Ba{sub 3}GeS{sub 5} and Ba{sub 3}InS{sub 4}Cl, were synthesized by using high temperature solid-state reactions and their structures were determined by single-crystal X-ray diffraction technique. Despite the similar chemical formula, the structures of Ba{sub 3}GeS{sub 5} and Ba{sub 3}InS{sub 4}Cl are subtly different due to the size effects originated from the tetrahedral anions. Ba{sub 3}GeS{sub 5} crystallizes in the orthorhombic space group Pnma (no. 62) with cell parameters of a=12.0528(9) Å, b=9.5497(7) Å and c=8.5979(6) Å, while Ba{sub 3}InS{sub 4}Cl adopts a different tetragonal system (space group: I4/mcm, no. 140, a=b=8.3613(6) Å, c=14.3806(18) Å). The measuredmore » optical band gap of Ba{sub 3}GeS{sub 5} is 3.0 eV, a little smaller than the value of 3.42 eV in Ba{sub 3}InS{sub 4}Cl. Theoretical calculations by Wien2k are provided as well in order to better understand these results. - Graphical abstract: The polyhedral structure view for Ba{sub 3}GeS{sub 5} and Ba{sub 3}InS{sub 4}Cl in which Ba, S and Cl atoms are plotted in purple, red and green spheres. - Highlights: • Two new barium chalcogenides, Ba{sub 3}GeS{sub 5} and Ba{sub 3}InS{sub 4}Cl, were synthesized from the BaCl{sub 2}-flux reactions. • Their crystal structures feature discrete [MS{sub 4}] tetrahedra which embody interesting size effects. • Both compounds exhibit a band gap around 3.0 eV. • They are thermally stable up to 1073 K.« less

Critical current densities in superconducting Y-Ba-Cu-O prepared by chelating method

NASA Astrophysics Data System (ADS)

Fujisawa, Tadashi; Okuyama, Katsuro; Ohshima, Shigetoshi; Takagi, Akira

1990-10-01

The IDA, NTA, HEDTA, EDTA, TTHA, and DTPA chelating agents have been used to prepare the Y-Ba-Cu-O compounds whose critical current is presently investigated. It is noted that the precursor YBCO prepared from large stability-constant metal complexes (HEDTA, EDTA, DTPA, and TTHA) exhibited very fine and homogeneous particles. The critical current density of a 1 x 4 x 15 mm block of YBCO sintered at 880-910 C for 24 h and subsequently annealed at 500 C in an O2 flow was approximately 500 A/sq cm at 77 K, in zero magnetic field.

A comparison between elastic network interpolation and MD simulation of 16S ribosomal RNA.

PubMed

Kim, Moon K; Li, Wen; Shapiro, Bruce A; Chirikjian, Gregory S

2003-12-01

In this paper a coarse-grained method called elastic network interpolation (ENI) is used to generate feasible transition pathways between two given conformations of the core central domain of 16S Ribosomal RNA (16S rRNA). The two given conformations are the extremes generated by a molecular dynamics (MD) simulation, which differ from each other by 10A in root-mean-square deviation (RMSD). It takes only several hours to build an ENI pathway on a 1.5GHz Pentium with 512 MB memory, while the MD takes several weeks on high-performance multi-processor servers such as the SGI ORIGIN 2000/2100. It is shown that multiple ENI pathways capture the essential anharmonic motions of millions of timesteps in a particular MD simulation. A coarse-grained normal mode analysis (NMA) is performed on each intermediate ENI conformation, and the lowest 1% of the normal modes (representing about 40 degrees of freedom (DOF)) are used to parameterize fluctuations. This combined ENI/NMA method captures all intermediate conformations in the MD run with 1.5A RMSD on average. In addition, if we restrict attention to the time interval of the MD run between the two extreme conformations, the RMSD between the closest ENI/NMA pathway and the MD results is about 1A. These results may serve as a paradigm for reduced-DOF dynamic simulations of large biological macromolecules as well as a method for the reduced-parameter interpretation of massive amounts of MD data.

High-field transport properties of a P-doped BaFe2As2 film on technical substrate

PubMed Central

Iida, Kazumasa; Sato, Hikaru; Tarantini, Chiara; Hänisch, Jens; Jaroszynski, Jan; Hiramatsu, Hidenori; Holzapfel, Bernhard; Hosono, Hideo

2017-01-01

High temperature (high-Tc) superconductors like cuprates have superior critical current properties in magnetic fields over other superconductors. However, superconducting wires for high-field-magnet applications are still dominated by low-Tc Nb3Sn due probably to cost and processing issues. The recent discovery of a second class of high-Tc materials, Fe-based superconductors, may provide another option for high-field-magnet wires. In particular, AEFe2As2 (AE: Alkali earth elements, AE-122) is one of the best candidates for high-field-magnet applications because of its high upper critical field, Hc2, moderate Hc2 anisotropy, and intermediate Tc. Here we report on in-field transport properties of P-doped BaFe2As2 (Ba-122) thin films grown on technical substrates by pulsed laser deposition. The P-doped Ba-122 coated conductor exceeds a transport Jc of 105 A/cm2 at 15 T for main crystallographic directions of the applied field, which is favourable for practical applications. Our P-doped Ba-122 coated conductors show a superior in-field Jc over MgB2 and NbTi, and a comparable level to Nb3Sn above 20 T. By analysing the E − J curves for determining Jc, a non-Ohmic linear differential signature is observed at low field due to flux flow along the grain boundaries. However, grain boundaries work as flux pinning centres as demonstrated by the pinning force analysis. PMID:28079117

Synthesis, Structural and Morphological Property of BaSnO3 Nanopowder Prepared by Solid State Ceramic Method

NASA Astrophysics Data System (ADS)

John, Jibi; Mahadevan Pillai, V. P.; Thomas, Anitta Rose; Philip, Reji; Joseph, Jaison; Muthunatesan, S.; Ragavendran, V.; Prabhu, Radhakrishna

2017-05-01

BaSnO3 is a cubic perovskite-type oxide that behaves as an n-type semiconductor with a wide band gap of 3.4 eV and remains stable at temperatures up to 1000°C. It has wide applications such as thermally stable capacitors, humidity sensors, gas sensors, etc. Barium stannate has also been used in optical applications, in capacitors and ceramic boundary layers, and as a promising material to produce gas phase sensors for the detection of carbon monoxide and carbon dioxide. BaSnO3 powder was prepared by solid state ceramic method. X-ray diffraction pattern of the prepared sample presents all the characteristic peaks of cubic phase of BaSnO3 (JCPDScard no: 15 -0780). The lattice constant for the compound was calculated and found to be 4.101A0 which is in agreement with the reported value (4.112A0). The average size of the crystallites estimated by Debye Scherrer’s formula was found to be 49 nm shows the nanostructured nature. The Raman bands observed ~ 139, 833 and 1122 cm-1 can be assigned on the basis of the fundamental vibrations of SnO6 octahedron which has Oh symmetry, in the distorted perovskite structure. The SEM image shows a porous surface morphology with grains of cuboidal structure with well-defined grain boundaries. UV-Visible spectra shows BaSnO3powder exhibit high reflectance in the 400-700 nm range.

High-field transport properties of a P-doped BaFe2As2 film on technical substrate

NASA Astrophysics Data System (ADS)

Iida, Kazumasa; Sato, Hikaru; Tarantini, Chiara; Hänisch, Jens; Jaroszynski, Jan; Hiramatsu, Hidenori; Holzapfel, Bernhard; Hosono, Hideo

2017-01-01

High temperature (high-Tc) superconductors like cuprates have superior critical current properties in magnetic fields over other superconductors. However, superconducting wires for high-field-magnet applications are still dominated by low-Tc Nb3Sn due probably to cost and processing issues. The recent discovery of a second class of high-Tc materials, Fe-based superconductors, may provide another option for high-field-magnet wires. In particular, AEFe2As2 (AE: Alkali earth elements, AE-122) is one of the best candidates for high-field-magnet applications because of its high upper critical field, Hc2, moderate Hc2 anisotropy, and intermediate Tc. Here we report on in-field transport properties of P-doped BaFe2As2 (Ba-122) thin films grown on technical substrates by pulsed laser deposition. The P-doped Ba-122 coated conductor exceeds a transport Jc of 105 A/cm2 at 15 T for main crystallographic directions of the applied field, which is favourable for practical applications. Our P-doped Ba-122 coated conductors show a superior in-field Jc over MgB2 and NbTi, and a comparable level to Nb3Sn above 20 T. By analysing the E - J curves for determining Jc, a non-Ohmic linear differential signature is observed at low field due to flux flow along the grain boundaries. However, grain boundaries work as flux pinning centres as demonstrated by the pinning force analysis.

All-solid-state, synchronously pumped, ultrafast BaWO4 Raman laser with long and short Raman shifts generating at 1180, 1225, and 1323 nm

NASA Astrophysics Data System (ADS)

Frank, Milan; Jelínek, Michal; Kubeček, Václav; Ivleva, Lyudmila I.; Zverev, Petr G.; Smetanin, Sergei

2017-12-01

A lot of attention is currently focused on synchronously pumped, extra-cavity crystalline Raman lasers generating one or two Stokes Raman components in KGW or diamond Raman-active crystals, and also generating additional components of stimulated polariton scattering in lithium niobate crystal having both cubic and quadratic nonlinearities. In this contribution we report on generation of more than two Stokes components of stimulated Raman scattering with different Raman shifts in the all-solid-state, synchronously pumped, extra-cavity Raman laser based on the Raman-active a-cut BaWO4 crystal excited by a mode-locked, 220 nJ, 36 ps, 150 MHz diode sidepumped Nd:GdVO4 laser generating at the wavelength of 1063 nm. Excitation by the pumping radiation polarized along the BaWO4 crystal optical axis resulted in the Raman generation with not only usual (925cm - 1), but also additional (332cm - 1) Raman shift. Besides the 1180-nm first and 1323 nm second Stokes components with the Raman shift of 925cm - 1 from the 1063nm fundamental laser wavelength, we have achieved generation of the additional 1227 nm Raman component with different Raman shift of 332cm - 1 from the 1180nm component. At the 1227 nm component the strongest 12-times pulse shortening from 36ps down to 3ps was obtained due to shorter dephasing time of this additional Raman line (3ps for the 332-cm - 1 line instead of 6.5ps for the 925cm - 1 line). It has to be also noted that the 1225 nm generation is intracavity pumped by the 1179 nm first Stokes component resulting in the strongest pulse shortening close to the 332cm -1 line dephasing time (3ps). Slope efficiency of three Stokes components generation exceeded 20%.

Growth of BaSi2 continuous films on Ge(111) by molecular beam epitaxy and fabrication of p-BaSi2/n-Ge heterojunction solar cells

NASA Astrophysics Data System (ADS)

Takabe, Ryota; Yachi, Suguru; Tsukahara, Daichi; Toko, Kaoru; Suemasu, Takashi

2017-05-01

We grew BaSi2 films on Ge(111) substrates by various growth methods based on molecular beam epitaxy (MBE). First, we attempted to form BaSi2 films directly on Ge(111) by MBE without templates. We next formed BaSi2 films using BaGe2 templates as commonly used for MBE growth of BaSi2 on Si substrates. Contrary to our prediction, the lateral growth of BaSi2 was not promoted by these two methods; BaSi2 formed not into a continuous film but into islands. Although streaky patterns of reflection high-energy electron diffraction were observed inside the growth chamber, no X-ray diffraction lines of BaSi2 were observed in samples taken out from the growth chamber. Such BaSi2 islands were easily to get oxidized. We finally attempted to form a continuous BaSi2 template layer on Ge(111) by solid phase epitaxy, that is, the deposition of amorphous Ba-Si layers onto MBE-grown BaSi2 epitaxial islands, followed by post annealing. We achieved the formation of an approximately 5-nm-thick BaSi2 continuous layer by this method. Using this BaSi2 layer as a template, we succeeded in forming a-axis-oriented 520-nm-thick BaSi2 epitaxial films on Ge substrates, although (111)-oriented Si grains were included in the grown layer. We next formed a B-doped p-BaSi2(20 nm)/n-Ge(111) heterojunction solar cell. A wide-spectrum response from 400 to 2000 nm was achieved. At an external bias voltage of 1 V, the external quantum efficiency reached as high as 60%, demonstrating the great potential of BaSi2/Ge combination. However, the efficiency of a solar cell under AM1.5 illumination was quite low (0.1%). The origin of such a low efficiency was examined.

75 FR 79063 - Maryland Disaster #MD-00014

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-17

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12411 and 12412] Maryland Disaster MD-00014 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a notice of an Administrative declaration of a disaster for the State of Maryland dated 12/09/2010. Incident: Severe Storms and...

Pharmacokinetics of [ 14C]-Benzo[a]pyrene (BaP) in humans: Impact of Co-Administration of smoked salmon and BaP dietary restriction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hummel, Jessica M.; Madeen, Erin P.; Siddens, Lisbeth K.

Benzo[a]pyrene (BaP), a polycyclic aromatic hydrocarbon (PAH), is a known human carcinogen. In non-smoking adults greater than 95% of BaP exposure is through diet. The carcinogenicity of BaP is utilized by the U.S. EPA to assess relative potency of complex PAH mixtures. PAH relative potency factors (RPFs, BaP=1) are determined from high dose animal data. Here we employed accelerator mass spectrometry (AMS) to determine pharmacokinetics of [ 14C]-BaP in humans following dosing with 46 ng (an order of magnitude lower than human dietary daily exposure and million-fold lower than animal cancer models). To assess the impact of co-administration of foodmore » with a complex PAH mixture, humans were dosed with 46 ng of [ 14C]-BaP with or without smoked salmon. Subjects were asked to avoid high BaP-containing diets and a 3-day dietary questionnaire given to assess dietary exposure prior to dosing and three days post-dosing with [ 14C]-BaP. Co-administration of smoked salmon, containing a complex mixture of PAHs with an RPF of 460 ng BaP eq, reduced and delayed absorption. Administration of canned commercial salmon, containing very low amounts of PAHs, showed the impacts on pharmacokinetics were not due to high amounts of PAHs but rather a food matrix effect.« less

Pharmacokinetics of [ 14C]-Benzo[a]pyrene (BaP) in humans: Impact of Co-Administration of smoked salmon and BaP dietary restriction

DOE PAGES

Hummel, Jessica M.; Madeen, Erin P.; Siddens, Lisbeth K.; ...

2018-03-01

Benzo[a]pyrene (BaP), a polycyclic aromatic hydrocarbon (PAH), is a known human carcinogen. In non-smoking adults greater than 95% of BaP exposure is through diet. The carcinogenicity of BaP is utilized by the U.S. EPA to assess relative potency of complex PAH mixtures. PAH relative potency factors (RPFs, BaP=1) are determined from high dose animal data. Here we employed accelerator mass spectrometry (AMS) to determine pharmacokinetics of [ 14C]-BaP in humans following dosing with 46 ng (an order of magnitude lower than human dietary daily exposure and million-fold lower than animal cancer models). To assess the impact of co-administration of foodmore » with a complex PAH mixture, humans were dosed with 46 ng of [ 14C]-BaP with or without smoked salmon. Subjects were asked to avoid high BaP-containing diets and a 3-day dietary questionnaire given to assess dietary exposure prior to dosing and three days post-dosing with [ 14C]-BaP. Co-administration of smoked salmon, containing a complex mixture of PAHs with an RPF of 460 ng BaP eq, reduced and delayed absorption. Administration of canned commercial salmon, containing very low amounts of PAHs, showed the impacts on pharmacokinetics were not due to high amounts of PAHs but rather a food matrix effect.« less

Effect of heavy-ion irradiation on London penetration depth in overdoped Ba(Fe 1 - x Co x ) 2 As 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murphy, J.; Tanatar, M. A.; Kim, Hyunsoo

2013-08-01

Irradiation with 1.4 GeV 208 Pb ions was used to induce artificial disorder in single crystals of iron-arsenide superconductor Ba(Fe 1 - x Co x ) 2 As 2 and to study its effects on the temperature-dependent London penetration depth and transport properties. A study was undertaken on overdoped single crystals with x = 0.108 and x = 0.127 characterized by notable modulation of the superconducting gap. Irradiation corresponding to the matching fields of B Φ = 6 T and 6.5 T with doses 2.22 × 10 11 d /cm 2 and 2.4 × 10 11 d /cm 2 ,more » respectively, suppresses the superconducting T c by approximately 0.3 to 1 K. The variation of the low-temperature penetration depth in both pristine and irradiated samples is well described by the power law Δ λ ( T ) = A T n . Irradiation increases the magnitude of the prefactor A and decreases the exponent n , similar to the effect of irradiation in optimally-doped samples. This finding supports universal s ± pairing in Ba(Fe 1 - x Co x ) 2 As 2 compounds for the entire Co doping range.« less

When one becomes two: Ba12In4Se20, not quite isostructural to Ba12In4S19

NASA Astrophysics Data System (ADS)

Yin, Wenlong; Iyer, Abishek K.; Li, Chao; Yao, Jiyong; Mar, Arthur

2017-09-01

The ternary selenide Ba12In4Se20 was synthesized by reaction of BaSe, In2Se3, and Se at 1023 K. Single-crystal X-ray diffraction revealed a trigonal structure (space group R 3 bar, Z = 6, a = 10.0360(6) Å, c = 78.286(4) Å at room temperature) consisting of one-dimensional stacks of InSe4 tetrahedra, In2Se7 double tetrahedra, selenide Se2- anions, and diselenide Se22- anions, with Ba2+ cations in the intervening spaces. The selenide Ba12In4Se20 can be derived from the corresponding sulfide Ba12In4S19 by replacing one monoatomic Ch2- anion with a diatomic Ch22- anion. An optical band gap of 1.70(2) eV, consistent with the dark red colour of the crystals, was deduced from the UV-vis-NIR diffuse reflectance spectrum.

Effect of high-energy electron irradiation in an electron microscope column on fluorides of alkaline earth elements (CaF2, SrF2, and BaF2)

NASA Astrophysics Data System (ADS)

Nikolaichik, V. I.; Sobolev, B. P.; Zaporozhets, M. A.; Avilov, A. S.

2012-03-01

The effect of high-energy (150 eV) electron irradiation in an electron microscope column on crystals of fluorides of alkaline earth elements CaF2, SrF2, and BaF2 is studied. During structural investigations by electron diffraction and electron microscopy, the electron irradiation causes chemical changes in MF2 crystals such as the desorption of fluorine and the accumulation of oxygen in the irradiated area with the formation of oxide MO. The fluorine desorption rate increases significantly when the electron-beam density exceeds the threshold value of ˜2 × 103 pA/cm2). In BaF2 samples, the transformation of BaO into Ba(OH)2 was observed when irradiation stopped. The renewal of irradiation is accompanied by the inverse transformation of Ba(OH)2 into BaO. In the initial stage of irradiation of all MF2 compounds, the oxide phase is in the single-crystal state with a lattice highly matched with the MF2 matrix. When the irradiation dose is increased, the oxide phase passes to the polycrystalline phase. Gaseous products of MF2 destruction (in the form of bubbles several nanometers in diameter) form a rectangular array with a period of ˜20 nm in the sample.

Lactobacillus farciminis MD, a newer strain with potential for bacteriocin and antibiotic assay.

PubMed

Halami, P M; Chandrashekar, A; Nand, K

2000-03-01

A native isolate Lactobacillus farciminis MD isolated from fermenting mushroom exhibited a high degree of sensitivity to the majority of the bacteriocins produced by strains of lactobacilli, leuconostoc and pediococci. Also, the efficacy of Lact. farciminis MD as a sensitive strain for antibiotic assay was established against different antibiotics including ampicillin, cefazoline, chloramphenicol and nitrofurantoin at concentrations of 30 microg each, showing an inhibition zone of 30 mm diameter. The high degree of sensitivity towards bacteriocins and antibiotics provide potential for the exploitation of Lact. farciminis MD in establishing very well-defined bacteriocin producers.

Innovative instrumentation for mineralogical and elemental analyses of solid extraterrestrial surfaces: The Backscatter Moessbauer Spectrometer/X Ray Fluorescence analyzer (BaMS/XRF)

NASA Technical Reports Server (NTRS)

Shelfer, T. D.; Morris, Richard V.; Nguyen, T.; Agresti, D. G.; Wills, E. L.

1994-01-01

We have developed a four-detector research-grade backscatter Moessbauer spectrometer (BaMS) instrument with low resolution x-ray fluorescence analysis (XRF) capability. A flight-qualified instrument based on this design would be suitable for use on missions to the surfaces of solid solar-system objects (Moon, Mars, asteroids, etc.). Target specifications for the flight instrument are as follows: mass less than 500 g; volumes less than 300 cu cm; and power less than 2 W. The BaMS/XRF instrument would provide data on the oxidation state of iron and its distribution among iron-bearing mineralogies and elemental composition information. This data is a primary concern for the characterization of extraterrestrial surface materials.

Monoclinic β-BaY2F8—a novel crystal simultaneously active for SRS and Ln3+-ion lasing

NASA Astrophysics Data System (ADS)

Kaminskii, A. A.; Lux, O.; Hanuza, J.; Rhee, H.; Eichler, H. J.; Zhang, J.; Tang, D.; Shen, D.; Yu, H.; Wang, J.; Yoneda, H.; Shirakawa, A.

2015-01-01

This paper presents the first investigation of stimulated Raman scattering (SRS) in the monoclinic fluoride crystal β-BaY2F8, which is known as a promising host-material for trivalent lanthanide (Ln3+) lasant ions. Picosecond laser excitation in the visible and near-IR spectral range at room temperature revealed the manifestation of nine SRS-promoting phonon modes, which are related to Ag and Bg vibrations of the crystal. Besides multi-phonon Stokes and anti-Stokes generation, we observed cross-cascaded χ(3) ↔ χ(3) processes involving different pairs of SRS-active phonons. A comparative estimation of the first Stokes steady-state Raman gain coefficients, both in the visible and near-IR region related to the most active SRS-phonon mode ωSRS1 ≈ 208 cm-1 of β-BaY2F8, was also performed. Furthermore, a brief review of the pioneering papers on laser action of Ln3+-ions doped in β-BaY2F8 single crystals and other known SRS-active fluoride crystals is given in tabular form.

Cross-scale MD simulations of dynamic strength of tantalum

NASA Astrophysics Data System (ADS)

Bulatov, Vasily

2017-06-01

Dislocations are ubiquitous in metals where their motion presents the dominant and often the only mode of plastic response to straining. Over the last 25 years computational prediction of plastic response in metals has relied on Discrete Dislocation Dynamics (DDD) as the most fundamental method to account for collective dynamics of moving dislocations. Here we present first direct atomistic MD simulations of dislocation-mediated plasticity that are sufficiently large and long to compute plasticity response of single crystal tantalum while tracing the underlying dynamics of dislocations in all atomistic details. Where feasible, direct MD simulations sidestep DDD altogether thus reducing uncertainties of strength predictions to those of the interatomic potential. In the specific context of shock-induced material dynamics, the same MD models predict when, under what conditions and how dislocations interact and compete with other fundamental mechanisms of dynamic response, e.g. twinning, phase-transformations, fracture. In collaboration with: Luis Zepeda-Ruiz, Lawrence Livermore National Laboratory; Alexander Stukowski, Technische Universitat Darmstadt; Tomas Oppelstrup, Lawrence Livermore National Laboratory. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Phase relationships in the BaO-Ga2O3-Ta2O5 system and the structure of Ba6Ga21TaO40.

PubMed

Cao, Jiang; Yu, Xiaodi; Kuang, Xiaojun; Su, Qiang

2012-07-16

Phase relationships in the BaO-Ga(2)O(3)-Ta(2)O(5) ternary system at 1200 °C were determined. The A(6)B(10)O(30) tetragonal tungsten bronze (TTB) related solution in the BaO-Ta(2)O(5) subsystem dissolved up to ~11 mol % Ga(2)O(3), forming a ternary trapezoid-shaped TTB-related solid solution region defined by the BaTa(2)O(6), Ba(1.1)Ta(5)O(13.6), Ba(1.58)Ga(0.92)Ta(4.08)O(13.16), and Ba(6)GaTa(9)O(30) compositions in the BaO-Ga(2)O(3)-Ta(2)O(5) system. Two ternary phases Ba(6)Ga(21)TaO(40) and eight-layer twinned hexagonal perovskite solid solution Ba(8)Ga(4-x)Ta(4+0.6x)O(24) were confirmed in the BaO-Ga(2)O(3)-Ta(2)O(5) system. Ba(6)Ga(21)TaO(40) crystallized in a monoclinic cell of a = 15.9130(2) Å, b = 11.7309(1) Å, c = 5.13593(6) Å, β = 107.7893(9)°, and Z = 1 in space group C2/m. The structure of Ba(6)Ga(21)TaO(40) was solved by the charge flipping method, and it represents a three-dimensional (3D) mixed GaO(4) tetrahedral and GaO(6)/TaO(6) octahedral framework, forming mixed 1D 5/6-fold tunnels that accommodate the Ba cations along the c axis. The electrical property of Ba(6)Ga(21)TaO(40) was characterized by using ac impedance spectroscopy.

Angiotensin II induces kidney inflammatory injury and fibrosis through binding to myeloid differentiation protein-2 (MD2).

PubMed

Xu, Zheng; Li, Weixin; Han, Jibo; Zou, Chunpeng; Huang, Weijian; Yu, Weihui; Shan, Xiaoou; Lum, Hazel; Li, Xiaokun; Liang, Guang

2017-03-21

Growing evidence indicates that angiotensin II (Ang II), a potent biologically active product of RAS, is a key regulator of renal inflammation and fibrosis. In this study, we tested the hypothesis that Ang II induces renal inflammatory injury and fibrosis through interaction with myeloid differentiation protein-2 (MD2), the accessory protein of toll-like receptor 4 (TLR4) of the immune system. Results indicated that in MD2 -/- mice, the Ang II-induced renal fibrosis, inflammation and kidney dysfunction were significantly reduced compared to control Ang II-infused wild-type mice. Similarly, in the presence of small molecule MD2 specific inhibitor L6H21 or siRNA-MD2, the Ang II-induced increases of pro-fibrotic and pro-inflammatory molecules were prevented in tubular NRK-52E cells. MD2 blockade also inhibited activation of NF-κB and ERK. Moreover, MD2 blockade prevented the Ang II-stimulated formation of the MD2/TLR4/MyD88 signaling complex, as well as the increased surface binding of Ang II in NRK-52E cells. In addition, Ang II directly bound recombinant MD2 protein, rather than TLR4 protein. We conclude that MD2 is a significant contributor in the Ang II-induced kidney inflammatory injury in chronic renal diseases. Furthermore, MD2 inhibition could be a new and important therapeutic strategy for preventing progression of chronic renal diseases.

MdMYB1 Regulates Anthocyanin and Malate Accumulation by Directly Facilitating Their Transport into Vacuoles in Apples.

PubMed

Hu, Da-Gang; Sun, Cui-Hui; Ma, Qi-Jun; You, Chun-Xiang; Cheng, Lailiang; Hao, Yu-Jin

2016-03-01

Tonoplast transporters, including proton pumps and secondary transporters, are essential for plant cell function and for quality formation of fleshy fruits and ornamentals. Vacuolar transport of anthocyanins, malate, and other metabolites is directly or indirectly dependent on the H(+)-pumping activities of vacuolar H(+)-ATPase (VHA) and/or vacuolar H(+)-pyrophosphatase, but how these proton pumps are regulated in modulating vacuolar transport is largely unknown. Here, we report a transcription factor, MdMYB1, in apples that binds to the promoters of two genes encoding the B subunits of VHA, MdVHA-B1 and MdVHA-B2, to transcriptionally activate its expression, thereby enhancing VHA activity. A series of transgenic analyses in apples demonstrates that MdMYB1/10 controls cell pH and anthocyanin accumulation partially by regulating MdVHA-B1 and MdVHA-B2. Furthermore, several other direct target genes of MdMYB10 are identified, including MdVHA-E2, MdVHP1, MdMATE-LIKE1, and MdtDT, which are involved in H(+)-pumping or in the transport of anthocyanins and malates into vacuoles. Finally, we show that the mechanism by which MYB controls malate and anthocyanin accumulation in apples also operates in Arabidopsis (Arabidopsis thaliana). These findings provide novel insights into how MYB transcription factors directly modulate the vacuolar transport system in addition to anthocyanin biosynthesis, consequently controlling organ coloration and cell pH in plants. © 2016 American Society of Plant Biologists. All Rights Reserved.

78 FR 32556 - Safety Zone; 2013 Ocean City Air Show, Atlantic Ocean; Ocean City, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-31

...-AA00 Safety Zone; 2013 Ocean City Air Show, Atlantic Ocean; Ocean City, MD AGENCY: Coast Guard, DHS... navigable waters of the Atlantic Ocean in the vicinity of Ocean City, MD to support the Ocean City Air Show... June 9, 2013, Ocean City, MD will host an air show event between Talbot Street and 33rd Street over the...

Image fusion in craniofacial virtual reality modeling based on CT and 3dMD photogrammetry.

PubMed

Xin, Pengfei; Yu, Hongbo; Cheng, Huanchong; Shen, Shunyao; Shen, Steve G F

2013-09-01

The aim of this study was to demonstrate the feasibility of building a craniofacial virtual reality model by image fusion of 3-dimensional (3D) CT models and 3 dMD stereophotogrammetric facial surface. A CT scan and stereophotography were performed. The 3D CT models were reconstructed by Materialise Mimics software, and the stereophotogrammetric facial surface was reconstructed by 3 dMD patient software. All 3D CT models were exported as Stereo Lithography file format, and the 3 dMD model was exported as Virtual Reality Modeling Language file format. Image registration and fusion were performed in Mimics software. Genetic algorithm was used for precise image fusion alignment with minimum error. The 3D CT models and the 3 dMD stereophotogrammetric facial surface were finally merged into a single file and displayed using Deep Exploration software. Errors between the CT soft tissue model and 3 dMD facial surface were also analyzed. Virtual model based on CT-3 dMD image fusion clearly showed the photorealistic face and bone structures. Image registration errors in virtual face are mainly located in bilateral cheeks and eyeballs, and the errors are more than 1.5 mm. However, the image fusion of whole point cloud sets of CT and 3 dMD is acceptable with a minimum error that is less than 1 mm. The ease of use and high reliability of CT-3 dMD image fusion allows the 3D virtual head to be an accurate, realistic, and widespread tool, and has a great benefit to virtual face model.

Complex refractive index measurements for BaF 2 and CaF 2 via single-angle infrared reflectance spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelly-Gorham, Molly Rose K.; DeVetter, Brent M.; Brauer, Carolyn S.

We have re-investigated the optical constants n and k for the homologous series of inorganic salts barium fluoride (BaF2) and calcium fluoride (CaF2) using a single-angle near-normal incidence reflectance device in combination with a calibrated Fourier transform infrared (FTIR) spectrometer. Our results are in good qualitative agreement with most previous works. However, certain features of the previously published data near the reststrahlen band exhibit distinct differences in spectral characteristics. Notably, our measurements of BaF2 do not include a spectral feature in the ~250 cm-1 reststrahlen band that was previously published. Additionally, CaF2 exhibits a distinct wavelength shift relative to themore » model derived from previously published data. We confirmed our results with recently published works that use significantly more modern instrumentation and data reduction techniques« less

Electrical properties of Ba doped LSGM for electrolyte material of solid oxide fuel cells

NASA Astrophysics Data System (ADS)

Raghvendra, Singh, Prabhakar; Singh, Rajesh Kumar

2013-02-01

We report our investigations on Lanthanum Strontium Magnesium Gallate, LSGM, La0.8Sr0.2Ga0.8Mg0.2O3-δ doped with Barium at Strontium site having composition La0.8(Sr0.1Ba0.1)Ga0.8Mg0.2O3-δ (LSBGM). The pure cubic phase along with some additional phase was confirmed by XRD pattern. Electrical properties of the Composition LSBGM [La0.8(Sr0.1Ba0.1)Ga0.8Mg0.2O3-δ] prepared by solid state route, was studied employing impedance spectroscopy in the temperature range 573 K-993 K and frequency range 20 Hz-1MHz. The total ionic conductivity of the composition was found to be 0.072 S.cm-1 at 953 K and the activation energy from Arrhenius plot was found to be 1.16 eV in the measured temperature range. This confirms oxygen ion conductivity in the system. SEM micrograph shows the uniform densed particle morphology with gains of average size 200 nm.

Growth and characterization of BaZnGa

DOE PAGES

Jo, Na Hyun; Lin, Qisheng; Nguyen, Manh Cuong; ...

2017-10-20

In this paper, we report the growth, structure and characterization of BaZnGa, identifying it as the sole known ternary compound in the Ba–Zn–Ga system. Single crystals of BaZnGa can be grown out of excess Ba–Zn and adopt a tI36 structure type. There are three unique Ba sites and three M = Zn/Ga sites. Using DFT calculations we can argue that whereas one of these three M sites is probably solely occupied by Ga, the other two M sites, most likely, have mixed Zn/Ga occupancy. Finally, temperature-dependent resistivity and magnetization measurements suggest that BaZnGa is a poor metal with no electronicmore » or magnetic phase transitions between 1.8 and 300 K.« less

Epigenetic regulation of MdMYB1 is associated with paper bagging-induced red pigmentation of apples.

PubMed

Bai, Songling; Tuan, Pham Anh; Saito, Takanori; Honda, Chikako; Hatsuyama, Yoshimichi; Ito, Akiko; Moriguchi, Takaya

2016-09-01

Paper-bagging treatment can transform non-transcribed MdMYB1 - 2 and MdMYB1 - 3 alleles into transcribed alleles through epigenetic regulations, resulting in the red pigmentation of a normally non-red apple cultivar 'Mutsu.' Anthocyanin biosynthesis in apples is regulated by MdMYB1/A/10, an R2R3-Type MYB gene. 'Mutsu,' a triploid apple cultivar harboring non-transcribed MdMYB1-2 and MdMYB1-3 alleles, retains green skin color under field conditions. However, it can show red/pink pigmentation under natural or artificial ultraviolet-B (UV-B) light exposure after paper-bagging and bag removal treatment. In the present study, we found that in 'Mutsu,' paper bagging-induced red pigmentation was due to the activation of non-transcribed MdMYB1-2/-3 alleles, which triggered the expression of downstream anthocyanin biosynthesis genes in a UV-B-dependent manner. By monitoring the epigenetic changes during UV-B-induced pigmentation, no significant differences in DNA methylation and histone modifications in the 5' upstream region of MdMYB1-2/-3 were recorded between the UV-B-treated fruit skin (red) and the fruit skin treated only by white light (green). In contrast, bag treatment lowered the DNA methylation in this region of MdMYB1-2/-3 alleles. Similarly, higher levels of histone H3 acetylation and trimethylation of H3 tail at lysine 4, and lower level of trimethylation of H3 tail at lysine 27 were observed in the 5' upstream region of MdMYB1-2/-3 in the skin of the fruit immediately after bag removal. These results suggest that bagging treatment can induce epigenetic changes, facilitating the binding of trans factor(s) to MdMYB1-2/-3 alleles, resulting in the activation of these MYBs after bag removal.

Continuous Structural Transition in Glass-Forming Molten Titanate BaTi 2 O 5

DOE PAGES

Alderman, O. L. G.; Benmore, C. J.; Tamalonis, A.; ...

2016-12-01

The structure of the model titanate glass former BaTi2O5 has been studied over a wide temperature (T) range in the molten, supercooled, and glassy states under conditions of aerodynamic levitation. Both high-energy X-ray diffraction and Ti K-edge X-ray absorption spectroscopy reveal a continuous structural transition involving reduction of the cation-oxygen (and oxygen-cation) average coordination numbers and bond lengths with increasing T. Ti-0 coordination in the moderately supercooled and equilibrium melt follows a linear trend n(Tio) = 5.4(1)- [3.5(7) x 10(-4)]T [K] (1300 <= T <= 1830 K, T-g = 960 K, T-m = 1660 K). Comparison to the melt-quenched glassmore » implies an increase in partial derivative n(Tio)/partial derivative T at lower T, as T-g is approached from above. Both Ba-0 coordination and bond length also decrease at higher T, and the role of Ba addition is to reduce n(Tio) below its value in pure molten TiO2, which is related to the presence of density maxima in molten BaO-TiO2. Density measurements made by imaging of the levitated melt yielded rho(T) = 4.82(55)- 0.0004(3)T in units of K and g cm(-3). While BaTi2O5 glass likely consists of a fully connected Ti-0 network, free of nonbridging oxygen (NBO) [OTi1 and with at least 13(4)% [OTi3] triclusters, the 1835(40) K equilibrium melt contains at least 10(4)% NBO along with 90(4)% bridging oxygen [OTi2]. The results highlight the fact that glasses can be considered as structural analogues of melts only for those melts deeply supercooled into the glass transition region. The results imply possible fictive T dependence of titanate glass structure, suggesting applications as, e.g., laser written waveguides with large refractive indices and refractive index contrasts. The temperature-dependent structure further implies a super-Arrhenian melt viscosity with consequences for glass manufacture, titanate-rich slags produced in iron smelting, TiO2-bearing magmas, and by analogy silicate melts at high

Self-assembled Co-BaZrO 3 nanocomposite thin films with ultra-fine vertically aligned Co nanopillars

DOE PAGES

Huang, Jijie; Li, Leigang; Lu, Ping; ...

2017-05-11

A simple one-step pulsed laser deposition (PLD) method has been applied to grow self-assembled metal-oxide nanocomposite thin films. The as-deposited Co-BaZrO 3 films show high epitaxial quality with ultra-fine vertically aligned Co nanopillars (diameter <5 nm) embeded in BZO matrix. The diameter of the nanopillars can be further tuned by varying the deposition frequency. The metal and oxide phases grow separately without inter-diffusion or mixing. Taking advantage of this unique structure, a high saturation magnetization of ~1375 emu/cm 3 in the Co- BaZrO 3 nanocomposites has been achieved and further confirmed by Lorentz microscopy imaging in TEM. Furthermore, the coercivitymore » values of this nanocomposite thin films range from 600 Oe (20 Hz) to 1020 Oe (2 Hz), which makes the nanocomposite an ideal candidate for high-density perpendicular recording media.« less

Potential for high thermoelectric performance in n-type Zintl compounds: A case study of Ba doped KAlSb 4

DOE PAGES

Ortiz, Brenden R.; Gorai, Prashun; Krishna, Lakshmi; ...

2017-01-11

High-throughput calculations (first-principles density functional theory and semi-empirical transport models) have the potential to guide the discovery of new thermoelectric materials. Herein we have computationally assessed the potential for thermoelectric performance of 145 complex Zintl pnictides. Of the 145 Zintl compounds assessed, 17% show promising n-type transport properties, compared with only 6% showing promising p-type transport. We predict that n-type Zintl compounds should exhibit high mobility μ n while maintaining the low thermal conductivity κ L typical of Zintl phases. Thus, not only do candidate n-type Zintls outnumber their p-type counterparts, but they may also exhibit improved thermoelectric performance. Frommore » the computational search, we have selected n-type KAlSb 4 as a promising thermoelectric material. Synthesis and characterization of polycrystalline KAlSb 4 reveals non-degenerate n-type transport. With Ba substitution, the carrier concentration is tuned between 10 18 and 10 19 e – cm –3 with a maximum Ba solubility of 0.7% on the K site. High temperature transport measurements confirm a high μ n (50 cm 2 V –1 s –1) coupled with a near minimum κ L (0.5 W m –1 K –1) at 370 °C. Together, these properties yield a zT of 0.7 at 370 °C for the composition K 0.99Ba 0.01AlSb 4. As a result, based on the theoretical predictions and subsequent experimental validation, we find significant motivation for the exploration of n-type thermoelectric performance in other Zintl pnictides.« less

Potential for high thermoelectric performance in n-type Zintl compounds: A case study of Ba doped KAlSb 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortiz, Brenden R.; Gorai, Prashun; Krishna, Lakshmi

High-throughput calculations (first-principles density functional theory and semi-empirical transport models) have the potential to guide the discovery of new thermoelectric materials. Herein we have computationally assessed the potential for thermoelectric performance of 145 complex Zintl pnictides. Of the 145 Zintl compounds assessed, 17% show promising n-type transport properties, compared with only 6% showing promising p-type transport. We predict that n-type Zintl compounds should exhibit high mobility μ n while maintaining the low thermal conductivity κ L typical of Zintl phases. Thus, not only do candidate n-type Zintls outnumber their p-type counterparts, but they may also exhibit improved thermoelectric performance. Frommore » the computational search, we have selected n-type KAlSb 4 as a promising thermoelectric material. Synthesis and characterization of polycrystalline KAlSb 4 reveals non-degenerate n-type transport. With Ba substitution, the carrier concentration is tuned between 10 18 and 10 19 e – cm –3 with a maximum Ba solubility of 0.7% on the K site. High temperature transport measurements confirm a high μ n (50 cm 2 V –1 s –1) coupled with a near minimum κ L (0.5 W m –1 K –1) at 370 °C. Together, these properties yield a zT of 0.7 at 370 °C for the composition K 0.99Ba 0.01AlSb 4. As a result, based on the theoretical predictions and subsequent experimental validation, we find significant motivation for the exploration of n-type thermoelectric performance in other Zintl pnictides.« less

Ubiquitous CM and DM

NASA Technical Reports Server (NTRS)

Crowley, Sandra L.

2000-01-01

Ubiquitous is a real word. I thank a former Total Quality Coach for my first exposure some years ago to its existence. My version of Webster's dictionary defines ubiquitous as "present, or seeming to be present, everywhere at the same time; omnipresent." While I believe that God is omnipresent, I have come to discover that CM and DM are present everywhere. Oh, yes; I define CM as Configuration Management and DM as either Data or Document Management. Ten years ago, I had my first introduction to the CM world. I had an opportunity to do CM for the Space Station effort at the NASA Lewis Research Center. I learned that CM was a discipline that had four areas of focus: identification, control, status accounting, and verification. I was certified as a CMIl graduate and was indoctrinated about clear, concise, and valid. Off I went into a world of entirely new experiences. I was exposed to change requests and change boards first hand. I also learned about implementation of changes, and then of technical and CM requirements.

Phase-pure eutectic CoFe2O4-Ba1-xSrxTiO3 composites prepared by floating zone melting

NASA Astrophysics Data System (ADS)

Breitenbach, Martin; Ebbinghaus, Stefan G.

2018-02-01

Composites consisting of ferrimagnetic CoFe2O4 and ferroelectric Ba1-xSrxTiO3 were grown by the floating zone technique. The influence of Sr substitution, growth rate and atmosphere during the floating zone process were investigated. The formation of the non-ferroelectric, hexagonal modification of BaTiO3 was avoided by a slight Sr substitution of 3 mol% and the formation of BaFe12O19 was suppressed using pure nitrogen as atmosphere during the floating zone melting. These synthesis parameters led to phase-pure, but electrically conductive CoFe2O4-Ba1-xSrxTiO3 composites. A thermal treatment at 973 K in air resulted in a strong increase of the electric resistivity accompanied by a decrease of the unit-cell parameters of both components indicating the healing of oxygen defects. SEM investigations revealed a variety of different geometric structures and crack-free interfaces between both phases. The low porosities observed in the micrographs correspond with densities above 90%. Magnetoelectric (ME) measurements confirmed a coupling between the ferroic orders of both phases with a hysteresis and maximum αME of 1.3 mV Oe-1 cm-1.

The interaction of NO2 with BaO: from cooperative adsorption to Ba(NO3)2 formation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yi, Cheol-Woo W.; Kwak, Ja Hun; Szanyi, Janos

2007-10-25

The effect of water on the morphology of BaO/Al2O3-based NOx storage materials was investigated using Fourier transform infrared spectroscopy, temperature programmed desorption, and time-resolved synchrotron X-ray diffraction techniques. The results of this multi-spectroscopy study reveal that, in the presence of water, surface Ba-nitrates convert to bulk nitrates, and water facilitates the formation of large Ba(NO3)2 particles. The conversion of surface to bulk Ba-nitrates is completely reversible, i.e. after the removal of water from the storage material a significant fraction of the bulk nitrates re-convert to surface nitrates. NO2 exposure of a H2O-containing (wet) BaO/Al2O3 sample results in the formation ofmore » nitrites and bulk nitrates exclusively, i.e. no surface nitrates form. After further exposure to NO2, the nitrites completely convert to bulk nitrates. The amount of NOx taken up by the storage material is, however, essentially unaffected by the presence of water, regardless of whether the water was dosed prior to or after NO2 exposure. Based on the results of this study we are now able to explain most of the observations reported in the literature on the effect of water on NOx uptake on similar storage materials.« less

The MdTFL1 gene of apple (Malus x domestica Borkh.) reduces vegetative growth and generation time.

PubMed

Flachowsky, Henryk; Szankowski, Iris; Waidmann, Sascha; Peil, Andreas; Tränkner, Conny; Hanke, Magda-Viola

2012-10-01

TFL1 is known as a floral repressor in Arabidopsis thaliana (L.) Heynh. In apple there are two TFL1 homologs, MdTFL1-1 and MdTFL1-2. The MdTFL1-1 gene was silenced in transgenic clones expressing a hairpin gene construct of a 323 bp fragment of MdTFL1-1. The hairpin gene construct was transferred to three different apple genotypes. Of 22 transgenic clones, 21 showed a significant reduction in MdTFL1-1 mRNA expression. Precocious flowering was obtained for 20 clones, which flowered already during in vitro cultivation. Nineteen clones could successfully be transferred to the greenhouse where 18 of them flowered within a few weeks followed by the death or at least a strongly inhibited vegetative growth of the plant. Most of the transgenic flowers developed abnormally. Results obtained on greenhouse-grown plants of the transgenic clones and transgenic seedlings clearly demonstrated the major role of MdTFL1 genes in maintaining the vegetative growth as prerequisite for a perennial lifecycle. It was shown that MdTFL1 dsRNAi promotes a life history similar to annual plants. Preliminary results obtained from grafting experiments with non-transgenic scions grafted onto MdTFL1 dsRNAi transgenic rootstocks indicated that the flower-inducing signal obtained after silencing of MdTFL1 genes seems not to be graft-transmissible.

Spontaneous and training-induced cortical plasticity in MD patients: Hints from lateral masking.

PubMed

Maniglia, Marcello; Soler, Vincent; Cottereau, Benoit; Trotter, Yves

2018-01-08

Macular degeneration (MD) affects central vision and represents the leading cause of visual diseases in elderly population worldwide. As a consequence of central vision loss, MD patients develop a preferred retinal locus (PRL), an eccentric fixation point that replaces the fovea. Here, our aim was to determine whether and to what extent spontaneous plasticity takes place in the cortical regions formerly responding to central vision and whether a visual training based on perceptual learning (PL) can boost this plasticity within the PRL area. Spontaneous and PL-induced cortical plasticity were characterized by using lateral masking, a contrast sensitivity modulation induced by collinear flankers. This configuration is known to be sensitive to neural plasticity and underlies several rehabilitation trainings. Results in a group of 4 MD patients showed that collinear facilitation was similar to what observed in age- and eccentricity-matched controls. However, MD patients exhibited significantly reduced collinear inhibition, a sign of neural plasticity, consistent with the hypothesis of partial cortical reorganization. Three AMD patients from the same group showed a further reduction of inhibition after training, but not controls. This result suggests that PL might further boost neural plasticity, opening promising perspectives for the development of rehabilitation protocols for MD patients.

Simultaneous 13 cm/3 cm Single-pulse Observations of PSR B0329+54

NASA Astrophysics Data System (ADS)

Yan, Zhen; Shen, Zhi-Qiang; Manchester, R. N.; Ng, C.-Y.; Weltevrede, P.; Wang, Hong-Guang; Wu, Xin-Ji; Yuan, Jian-Ping; Wu, Ya-Jun; Zhao, Rong-Bing; Liu, Qing-Hui; Zhao, Ru-Shuang; Liu, Jie

2018-03-01

We have investigated the mode changing properties of PSR B0329+54 using 31 epochs of simultaneous 13 cm/3 cm single-pulse observations obtained with the Shanghai Tian Ma 65 m telescope. The pulsar was found in the abnormal emission mode 17 times, accounting for ∼13% of the 41.6 hr total observation time. Single-pulse analyses indicate that mode changes took place simultaneously at 13 cm/3 cm within a few rotational periods. We detected occasional bright and narrow pulses whose peak flux densities were 10 times higher than that of the integrated profile in both bands. At 3 cm, about 0.66% and 0.27% of single pulses were bright in the normal mode and abnormal mode, respectively, but at 13 cm the occurrence rate was only about 0.007%. We divided the pulsar radiation window into three components (C1, C2, and C3) corresponding to the main peaks of the integrated profile. The bright pulses preferentially occurred at pulse phases corresponding to the peaks of C2 and C3. Fluctuation spectra showed that C2 had excess red noise in the normal mode, but broad quasi-periodic features with central frequencies around 0.12 cycles/period in the abnormal mode. At 3 cm, C3 had a stronger quasi-periodic modulation centered around 0.06 cycles/period in the abnormal mode. Although there were some asymmetries in the two-dimensional fluctuation spectra, we found no clear evidence for systematic subpulse drifting. Consistent with previous low-frequency observations, we found a very low nulling probability for B0329+54, with upper limits of 0.13% and 1.68% at 13 cm/3 cm, respectively.

Tuning the giant magnetoelastic transition in Ba3BiIr2O9 and Ba3BiRu2O9

NASA Astrophysics Data System (ADS)

Huang, Zixin; Avdeev, Maxim; Kennedy, Brendan J.; Knight, Kevin S.; Zhou, Qingdi; Ling, Chris D.

2014-07-01

We have experimentally investigated the effects of pressure on the magnetoelastic transitions associated with the opening of spin-gaps in Ba3BiIr2O9 and Ba3BiRu2O9. For both compounds, reducing the unit cell volume by either external physical and internal chemical pressure was found to reduce the temperature T* of the transition and, to a lesser extent, the magnitude of the associated negative thermal volume expansion. The results yield the latent heat associated with the transitions, -3.34(3) × 102 J mol-1 for Ba3BiIr2O9 and -7.1(5) × 102 J mol-1 for Ba3BiRu2O9. The transition in Ba3BiRu2O9 is significantly more robust than in Ba3BiIr2O9, requiring an order of magnitude higher pressures to achieve the same reduction in T*. The differing responses of the two compounds points to differences between the 4d and 5d metals and hence to the importance of spin-orbit coupling, which is expected to be much stronger in the Ir compound.

Reproducibility of Ba/Ca variations recorded by northeast Pacific bamboo corals

NASA Astrophysics Data System (ADS)

Serrato Marks, G.; LaVigne, M.; Hill, T. M.; Sauthoff, W.; Guilderson, T. P.; Roark, E. B.; Dunbar, R. B.; Horner, T. J.

2017-09-01

Trace elemental ratios preserved in the calcitic skeleton of bamboo corals have been shown to serve as archives of past ocean conditions. The concentration of dissolved barium (BaSW), a bioactive nutrientlike element, is linked to biogeochemical processes such as the cycling and export of nutrients. Recent work has calibrated bamboo coral Ba/Ca, a new BaSW proxy, using corals spanning the oxygen minimum zone beneath the California Current System. However, it was previously unclear whether Ba/Cacoral records were internally reproducible. Here we investigate the accuracy of using laser ablation inductively coupled plasma mass spectrometry for Ba/Cacoral analyses and test the internal reproducibility of Ba/Ca among replicate radial transects in the calcite of nine bamboo corals collected from the Gulf of Alaska (643-720 m) and the California margin (870-2054 m). Data from replicate Ba/Ca transects were aligned using visible growth bands to account for nonconcentric growth; smoothed data were reproducible within 4% for eight corals (n = 3 radii/coral). This intracoral reproducibility further validates using bamboo coral Ba/Ca for BaSW reconstructions. Sections of the Ba/Ca records that were potentially influenced by noncarbonate bound Ba phases occurred in regions where elevated Mg/Ca or Pb/Ca and coincided with anomalous regions on photomicrographs. After removing these regions of the records, increased Ba/Cacoral variability was evident in corals between 800 and 1500 m. These findings support additional proxy validation to understand BaSW variability on interannual timescales, which could lead to new insights into deep sea biogeochemistry over the past several centuries.

Is BaCr 2 As 2 symmetrical to BaFe 2 As 2 with respect to half 3 d shell filling?

DOE PAGES

Richard, P.; van Roekeghem, A.; Lv, B. Q.; ...

2017-05-25

We have performed an angle-resolved photoemission spectroscopy study of BaCr 2As 2, which has the same crystal structure as BaFe2As2, a parent compound BaFe 2As 2 of Fe-based superconductors. We determine the Fermi surface of this material and its band dispersion down to 5 eV below the Fermi level. Very moderate band renormalization (1.35) is observed for only two bands. We attribute this small renormalization to enhanced direct exchange as compared to Fe in BaFe 2As 2, and to a larger contribution of the eg orbitals in the composition of the bands forming the Fermi surface.

An Assessment of the Oral Bioavailability of Three Ca-Channel Blockers Using a Cassette-Microdose Study: A New Strategy for Streamlining Oral Drug Development.

PubMed

Yamashita, Shinji; Kataoka, Makoto; Suzaki, Yuki; Imai, Hiromitsu; Morimoto, Takuya; Ohashi, Kyoichi; Inano, Akihiro; Togashi, Kazutaka; Mutaguchi, Kuninori; Sugiyama, Yuichi

2015-09-01

A cassette-microdose (MD) clinical study was performed to demonstrate its usefulness for identifying the most promising compound for oral use. Three Ca-channel blockers (nifedipine, nicardipine, and diltiazem) were chosen as model drugs. In the MD clinical study, a cassette-dose method was employed in which three model drugs were administered simultaneously. Both intravenous (i.v.) and oral (p.o.) administration studies were conducted to calculate the oral bioavailability (BA). For comparison, p.o. studies with therapeutic dose (ThD) levels were also performed. In all studies, blood concentrations of each drug were successfully determined using liquid chromatography-mass spectrometry with the lower limit of quantification of 0.2-2.0 pg/mL. Oral BA of nifedipine in the MD study was approximately 50% and in the same range with that obtained in the ThD study, whereas other two drugs showed significantly lower BA in the MD study, indicating a dose-dependent absorption. In addition, compared with the ThD study, absorption of nicardipine was delayed in the MD study. As a result, nifedipine was considered to be most promising for oral use. In conclusion, a cassette-MD clinical study is of advantage for oral drug development that enables to identify the candidate having desired properties for oral use. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Preparation of TlBa2Ca2Cu3O9±δ high Tc thin films by laser ablation in combination with thermal evaporation of thallium oxide

NASA Astrophysics Data System (ADS)

Piehler, A.; Löw, R.; Betz, J.; Schönberger, R.; Renk, K. F.

1993-11-01

TlBa2Ca2Cu3O9±δ high Tc thin films were prepared on MgO <100> surfaces by a combination of laser ablation from a stoichiometric Ba2Ca2Cu3Ox target and the thermal evaporation of thallium oxide. X-ray diffraction measurements showed that the films consisted of predominantly c axis oriented TlBa2Ca2Cu3O9±δ, and scanning electron microscopy revealed that the surfaces had a flat, platelike morphology. The ac inductive measurements indicated that the onset of superconductivity occurred at 117 K with a transition width (10%-90%) of ˜3 K. Zero resistivity was reached at 120 K. The critical current density was ˜3×104 A/cm2 at 110 K.

Band-offsets at BaTiO3/Cu2O heterojunction and enhanced photoelectrochemical response: theory and experiment(Conference Presentation)

NASA Astrophysics Data System (ADS)

Sharma, Dipika; Satsangi, Vibha R.; Dass Kaura, Sahab; Shrivastav, Rohit; Waghmare, Umesh V.

2016-10-01

Band-offsets at BaTiO3/Cu2O heterojunction and enhanced photoelectrochemical response: theory and experiment Dipika Sharmaa, Vibha R. Satsangib, Rohit Shrivastava, Umesh V. Waghmarec, Sahab Dassa aDepartment of Chemistry, Dayalbagh Educational Institute, Agra-282 110 (India) bDepartment of Physics and Computer Sciences, Dayalbagh Educational Institute, Agra-282 110 (India) cTheoretical Sciences Unit, Jawaharlal Nehru Centre for Advanced Scientific Research, Jakkur, Bangalore-560 064 (India) * Phone: +91-9219695960. Fax: +91-562-2801226. E-mail: drsahabdas@gmail.com. Study on photoelectrochemical activity of pristine BaTiO3, Cu2O and BaTiO3/Cu2O heterojunction has been carried out using DFT based band offsets and charge carriers effective mass calculations and their experimental verification. The results of DFT calculations show that BaTiO3 and Cu2O have staggered type band alignment after the heterojunction formation and high mobility of electrons in Cu2O as compared to the electrons in BaTiO3. Staggered type band edges alignment and high mobility of electrons and holes improved the separation of photo-generated charge carriers in BaTiO3/Cu2O heterojunction. To validate the theoretical results experiments were carried out on pristine BaTiO3, Cu2O and BaTiO3/Cu2O heterojunction with varying thickness of Cu2O. All samples were characterized by X- Ray Diffractometer, SEM and UV-Vis spectrometry. Nanostructured thin films of pristine BaTiO3, Cu2O and BaTiO3/Cu2O heterojunction were used as photoelectrode in the photoelectrochemical cell for water splitting reaction. Maximum photocurrent density of 1.44 mA/cm2 at 0.90 V/SCE was exhibited by 442 nm thick BaTiO3/Cu2O heterojunction photoelectrode Increased photocurrent density and enhanced photoconversion efficiency, exhibited by the heterojunction may be attributed to improved conductivity and enhanced separation of the photogenerated carriers at the BaTiO3/Cu2O interface. The experimental results and first

Biodistribution and Radiation Dosimetry of the Integrin Marker 64Cu-BaBaSar-RGD2 Determined from Whole-Body PET/CT in a Non-Human Primate

NASA Astrophysics Data System (ADS)

Liu, Shuanglong; Vorobyova, Ivetta; Park, Ryan; Conti, Peter S.

2017-10-01

Introduction: 64Cu-BaBaSar-RGD2 is a positron emission radiotracer taken up by integrin αvβ3, which is overexpressed in many malignancies. The aim of this study was to evaluate the biodistribution of 64Cu-BaBaSar-RGD2 in a non-human primate with positron emission tomography and to estimate the absorbed doses in major organs for human. Materials and methods: Whole-body PET imaging was done in a Siemens Biograph scanner in a male macaque monkey. After an i.v. injection of 13.1–19.7 MBq/kg of 64Cu-BaBaSar-RGD2, whole body scan was collected for a total duration of 180 min. Attenuation and scatter corrections were applied to reconstruction of the whole-body emission scan. After image reconstruction, three-dimensional volumes of interest (VOI) were hand-drawn on the PET transaxial or coronal slices of the frame where the organ was most conspicuous. Time-activity curves for each VOI were obtained, and residence time of each organ was calculated by integration of the time-activity curves. Human absorbed doses were estimated using the standard human model in OLINDA/EXM software. Results: Injection of 64Cu-BaBaSar-RGD2 was well tolerated in the macaque monkey, with no serious tracer-related adverse events observed. 64Cu-BaBaSar-RGD2 was cleared rapidly from the blood pool, with a 12.1-min biological half-time. Increased 64Cu-BaBaSar-RGD2 uptake was observed in the kidneys, and bladder, with mean percentage injected dose (ID%) values at 1 h after injection approximately 35.50 ± 6.47 and 36.89 ± 5.48, respectively. The calculated effective dose was 15.30 ± 2.21 µSv/MBq, and the kidneys had the highest absorbed dose at 108.43 ± 16.41 µGy/MBq using the non-voiding model. For an injected activity of 925 MBq 64Cu for human, the effective dose would be 14.2 ± 2.1 mSv. Discussion: Due to the limitation of the monkey number, we evaluated 64Cu-BaBaSar-RGD2 in the same monkey of three imaging sessions. Measured absorbed doses and effective doses of 64Cu-BaBaSar-RGD2 are

Lead-free 0.5Ba(Zr0.2Ti0.8)O3-0.5(Ba0.7Ca0.3)TiO3 nanowires for energy harvesting.

PubMed

Zhou, Zhi; Bowland, Christopher C; Malakooti, Mohammad H; Tang, Haixiong; Sodano, Henry A

2016-03-07

Lead-free piezoelectric nanowires (NWs) show strong potential in sensing and energy harvesting applications due to their flexibility and ability to convert mechanical energy to electric energy. Currently, most lead-free piezoelectric NWs are produced through low yield synthesis methods and result in low electromechanical coupling, which limit their efficiency as energy harvesters. In order to alleviate these issues, a scalable method is developed to synthesize perovskite type 0.5Ba(Zr0.2Ti0.8)O3-0.5(Ba0.7Ca0.3)TiO3 (BZT-BCT) NWs with high piezoelectric coupling coefficient. The piezoelectric coupling coefficient of the BZT-BCT NWs is measured by a refined piezoresponse force microscopy (PFM) testing method and shows the highest reported coupling coefficient for lead-free piezoelectric nanowires of 90 ± 5 pm V(-1). Flexible nanocomposites utilizing dispersed BZT-BCT NWs are fabricated to demonstrate an energy harvesting application with an open circuit voltage of up to 6.25 V and a power density of up to 2.25 μW cm(-3). The high electromechanical coupling coefficient and high power density demonstrated with these lead-free NWs produced via a scalable synthesis method shows the potential for high performance NW-based devices.

Understanding Ferromagnetic Phase Stability, Electronic and Transport Properties of BaPaO3 and BaNpO3 from Ab-Initio Calculations

NASA Astrophysics Data System (ADS)

Khandy, Shakeel Ahmad; Gupta, Dinesh C.

2017-10-01

An extensive study of rare-earth perovskite BaPaO3 and BaNpO3 has been performed by first-principles tactics based on density functional theory (DFT), because the delocalized f-electrons play an important role in the band structure formation, to reveal their impact on the overall physical and chemical properties; it has turned out to be an interesting theme. Along with critical radii and thermoelectric properties, two different theories are employed to calculate the structural properties. The DFT and empirically calculated lattice constants are in rational accord with the experimental results. The critical radius calculations show that the BaPaO3 lattice has a smaller oxygen migration activation energy than the BaNpO3. In addition, we discuss the band profile and magnetic moments for these materials, which demonstrate the half-metallic ferromagnetism with a direct energy gap of 3.91 eV for BaPaO3 and an indirect gap of 3.79 eV for BaNpO3. More interestingly, the integral magnetic moments are in accordance with the Slater-Pauling rule.

Find an Orthopaedic Foot and Ankle MD/DO

MedlinePlus

... All Site Content AOFAS / FootCareMD / Find a Surgeon Find a Foot & Ankle Orthopaedic Surgeon Page Content Who ... your prescribed treatment (surgical and/or non-surgical) ​ Find a Surgeon ​ Click here to find a foot ...

Molecular cloning and functional analysis of a blue light receptor gene MdCRY2 from apple (Malus domestica).

PubMed

Li, Yuan-Yuan; Mao, Ke; Zhao, Cheng; Zhao, Xian-Yan; Zhang, Rui-Fen; Zhang, Hua-Lei; Shu, Huai-Rui; Hao, Yu-Jin

2013-04-01

MdCRY2 was isolated from apple fruit skin, and its function was analyzed in MdCRY2 transgenic Arabidopsis. The interaction between MdCRY2 and AtCOP1 was found by yeast two-hybrid and BiFC assays. Cryptochromes are blue/ultraviolet-A (UV-A) light receptors involved in regulating various aspects of plant growth and development. Investigations of the structure and functions of cryptochromes in plants have largely focused on Arabidopsis (Arabidopsis thaliana), tomato (Solanum lycopersicum), pea (Pisum sativum), and rice (Oryza sativa). However, no data on the function of CRY2 are available in woody plants. In this study, we isolated a cryptochrome gene, MdCRY2, from apple (Malus domestica). The deduced amino acid sequences of MdCRY2 contain the conserved N-terminal photolyase-related domain and the flavin adenine dinucleotide (FAD) binding domain, as well as the C-terminal DQXVP-acidic-STAES (DAS) domain. Relationship analysis indicates that MdCRY2 shows the highest similarity to the strawberry FvCRY protein. The expression of MdCRY2 is induced by blue/UV-A light, which represents a 48-h circadian rhythm. To investigate the function of MdCRY2, we overexpressed the MdCRY2 gene in a cry2 mutant and wild type (WT) Arabidopsis, assessed the phenotypes of the resulting transgenic plants, and found that MdCRY2 functions to regulate hypocotyl elongation, root growth, flower initiation, and anthocyanin accumulation. Furthermore, we examined the interaction between MdCRY2 and AtCOP1 using a yeast two-hybrid assay and a bimolecular fluorescence complementation assay. These data provide functional evidence for a role of blue/UV-A light-induced MdCRY2 in controlling photomorphogenesis in apple.

High-field transport properties of a P-doped BaFe2As2 film on technical substrate.

PubMed

Iida, Kazumasa; Sato, Hikaru; Tarantini, Chiara; Hänisch, Jens; Jaroszynski, Jan; Hiramatsu, Hidenori; Holzapfel, Bernhard; Hosono, Hideo

2017-01-12

High temperature (high-T c ) superconductors like cuprates have superior critical current properties in magnetic fields over other superconductors. However, superconducting wires for high-field-magnet applications are still dominated by low-T c Nb 3 Sn due probably to cost and processing issues. The recent discovery of a second class of high-T c materials, Fe-based superconductors, may provide another option for high-field-magnet wires. In particular, AEFe 2 As 2 (AE: Alkali earth elements, AE-122) is one of the best candidates for high-field-magnet applications because of its high upper critical field, H c2 , moderate H c2 anisotropy, and intermediate T c . Here we report on in-field transport properties of P-doped BaFe 2 As 2 (Ba-122) thin films grown on technical substrates by pulsed laser deposition. The P-doped Ba-122 coated conductor exceeds a transport J c of 10 5  A/cm 2 at 15 T for main crystallographic directions of the applied field, which is favourable for practical applications. Our P-doped Ba-122 coated conductors show a superior in-field J c over MgB 2 and NbTi, and a comparable level to Nb 3 Sn above 20 T. By analysing the E - J curves for determining J c , a non-Ohmic linear differential signature is observed at low field due to flux flow along the grain boundaries. However, grain boundaries work as flux pinning centres as demonstrated by the pinning force analysis.

Conducting Retrospective Ontological Clinical Trials in ICD-9-CM in the Age of ICD-10-CM.

PubMed

Venepalli, Neeta K; Shergill, Ardaman; Dorestani, Parvaneh; Boyd, Andrew D

2014-01-01

To quantify the impact of International Classification of Disease 10th Revision Clinical Modification (ICD-10-CM) transition in cancer clinical trials by comparing coding accuracy and data discontinuity in backward ICD-10-CM to ICD-9-CM mapping via two tools, and to develop a standard ICD-9-CM and ICD-10-CM bridging methodology for retrospective analyses. While the transition to ICD-10-CM has been delayed until October 2015, its impact on cancer-related studies utilizing ICD-9-CM diagnoses has been inadequately explored. Three high impact journals with broad national and international readerships were reviewed for cancer-related studies utilizing ICD-9-CM diagnoses codes in study design, methods, or results. Forward ICD-9-CM to ICD-10-CM mapping was performing using a translational methodology with the Motif web portal ICD-9-CM conversion tool. Backward mapping from ICD-10-CM to ICD-9-CM was performed using both Centers for Medicare and Medicaid Services (CMS) general equivalence mappings (GEMs) files and the Motif web portal tool. Generated ICD-9-CM codes were compared with the original ICD-9-CM codes to assess data accuracy and discontinuity. While both methods yielded additional ICD-9-CM codes, the CMS GEMs method provided incomplete coverage with 16 of the original ICD-9-CM codes missing, whereas the Motif web portal method provided complete coverage. Of these 16 codes, 12 ICD-9-CM codes were present in 2010 Illinois Medicaid data, and accounted for 0.52% of patient encounters and 0.35% of total Medicaid reimbursements. Extraneous ICD-9-CM codes from both methods (Centers for Medicare and Medicaid Services general equivalent mapping [CMS GEMs, n = 161; Motif web portal, n = 246]) in excess of original ICD-9-CM codes accounted for 2.1% and 2.3% of total patient encounters and 3.4% and 4.1% of total Medicaid reimbursements from the 2010 Illinois Medicare database. Longitudinal data analyses post-ICD-10-CM transition will require backward ICD-10-CM to ICD-9-CM

33 CFR 165.509 - Security Zone; Severn River and College Creek, Annapolis, MD.

Code of Federal Regulations, 2010 CFR

2010-07-01

... College Creek, Annapolis, MD. 165.509 Section 165.509 Navigation and Navigable Waters COAST GUARD... § 165.509 Security Zone; Severn River and College Creek, Annapolis, MD. (a) Definitions. For purposes of... the Naval Academy waterfront. This security zone includes the waters of College Creek eastward of the...

Synthesis, Characterization, and Self-Controlled Orthorhombic to Tetragonal Polymorphic Transformation in BaTiO3 Nanoparticles

NASA Astrophysics Data System (ADS)

Ram, S.; Jana, A.; Kundu, T. K.

The phase formation and thermal-induced phase transformation are studied in BaTiO3 nanoparticles. 2 h of heating a polymer precursor at 550°C in air formed a single phase BaTiO3 of 15 nm average crystallite size D. The X-ray diffraction peaks are analyzed assuming a Pnma orthorhombic (o) crystal structure of lattice parameters a = 0.6435 nm, b = 0.5306 nm, and c = 0.8854 nm. The lattice volume V = 0.3023 nm3, with z = 4 formula units, yields a density ρ = 5.124 g/cm3. This is a new polymorph in comparison to well-known Pm3m tetragonal (t) structure, V = 0.0644 nm3 or ρ = 6.016 g/cm3 (z = 1). An o ↦ t transformation appears on heating at temperature as high as 650°C in air. A proposed model explains the transformation above a certain D value in terms of the Gibbs free energy. Unless heating above 750°C, the two phases coexist in a composite structure (D≤27 nm), with as much residual o-phase trace as ~28 vol%. As a function of temperature both the phases decrease in the V values up to 0.2975 and 0.0643 nm3 at 750°C respectively (0.0650 nm3 at 650°C). This is an important parameter for designing useful ferroelectric and other properties in a hybrid composite structure.

High critical currents in heavily doped (Gd,Y)Ba 2Cu 3O x superconductor tapes

DOE PAGES

Selvamanickam, V.; Gharahcheshmeh, M. Heydari; Xu, A.; ...

2015-01-20

REBa 2Cu 3O x superconductor tapes with moderate levels of dopants have been optimized for high critical current density in low magnetic fields at 77 K, but they do not exhibit exemplary performance in conditions of interest for practical applications, i.e., temperatures less than 50 K and fields of 2–30 T. Heavy doping of REBCO tapes has been avoided by researchers thus far due to deterioration in properties. Here, we report achievement of critical current densities (J c) above 20 MA/cm 2 at 30 K, 3 T in heavily doped (25 mol. % Zr-added) (Gd,Y)Ba 2Cu 3O x superconductor tapes,more » which is more than three times higher than the J c typically obtained in moderately doped tapes. Pinning force levels above 1000 GN/m 3 have also been attained at 20 K. A composition map of lift factor in J c (ratio of J c at 30 K, 3 T to the J c at 77 K, 0 T) has been developed which reveals the optimum film composition to obtain lift factors above six, which is thrice the typical value. A highly c-axis aligned BaZrO 3 (BZO) nanocolumn defect density of nearly 7 × 10 11 cm –2 as well as 2–3nm sized particles rich in Cu and Zr have been found in the high J c films.« less

Études RMN haute résolution et RPE des composés Ba 3C 60 et Ba 6C 60

NASA Astrophysics Data System (ADS)

Rezzouk, Abdellah; Dafir, Driss; Errammach, Youssef; Rachdi, Férid

2003-07-01

We report the results of 13C MAS NMR and EPR measurements on Ba 3C 60 and Ba 6C 60 fullerides. Using high resolution NMR, we were able to identify an isotropic line around 156 ppm for Ba 3C 60 and a broad isotropic one with three components at 132, 134.6, 139.9 ppm for Ba 6C 60 compound. The latter line is consistent with orientationally ordered C 60 molecules leading to three unequivalent carbon sites in agreement with X-ray studies. A strong diamagnetic shift was observed for the NMR line of Ba 6C 60 that is interpreted in terms of transition moment in an indirect gap system. EPR results confirm the insulating nature of both studied compounds. To cite this article: A. Rezzouk et al., C. R. Physique 4 (2003).

Water at silica/liquid water interfaces investigated by DFT-MD simulations

NASA Astrophysics Data System (ADS)

Gaigeot, Marie-Pierre

This talk is dedicated to probing the microscopic structural organization of water at silica/liquid water interfaces including electrolytes by first principles DFT-based molecular dynamics simulations (DFT-MD). We will present our very recent DFT-MD simulations of electrolytic (KCl, NaCl, NaI) silica/liquid water interfaces in order to unravel the intertwined structural properties of water and electrolytes at the crystalline quartz/liquid water and amorphous silica/liquid water interfaces. DFT-MD simulations provide direct knowledge of the structural organization of water and the H-Bond network formed between the water molecules within the different water layers above the silica surface. One can furthermore extract vibrational signatures of the water molecules within the interfacial layers from the DFT-MD simulations, especially non-linear SFG (Sum Frequency generation) signatures that are active at solid/liquid interfaces. The strength of the simulated spectra is that a detailed analysis of the signatures in terms of the water/water H-Bond networks formed within the interfacial water layers and in terms of the water/silica or water/electrolytes H-Bond networks can be given. Comparisons of SFG spectra between quartz/water/electrolytes and amorphous silica/water/electrolytes interfaces allow us to definitely conclude on how the structural arrangements of liquid water at these electrolytic interfaces modulate the final spectroscopic signatures. Invited speaker.

Computation of shear viscosity of colloidal suspensions by SRD-MD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laganapan, A. M. K.; Videcoq, A., E-mail: arnaud.videcoq@unilim.fr; Bienia, M.

2015-04-14

The behaviour of sheared colloidal suspensions with full hydrodynamic interactions (HIs) is numerically studied. To this end, we use the hybrid stochastic rotation dynamics-molecular dynamics (SRD-MD) method. The shear viscosity of colloidal suspensions is computed for different volume fractions, both for dilute and concentrated cases. We verify that HIs help in the collisions and the streaming of colloidal particles, thereby increasing the overall shear viscosity of the suspension. Our results show a good agreement with known experimental, theoretical, and numerical studies. This work demonstrates the ability of SRD-MD to successfully simulate transport coefficients that require correct modelling of HIs.

78 FR 11725 - Maryland Disaster Number MD-00024

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-19

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13425 and 13426] Maryland Disaster Number MD-00024 AGENCY: U.S. Small Business Administration. ACTION: Amendment 1. SUMMARY: This is an amendment of... information in the original declaration remains unchanged. (Catalog of Federal Domestic Assistance Numbers...

76 FR 70527 - Maryland Disaster Number MD-00018

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-14

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12874 and 12875] Maryland Disaster Number MD-00018 AGENCY: U.S. Small Business Administration. ACTION: Amendment 1. SUMMARY: This is an amendment of... the original declaration remains unchanged .(Catalog of Federal Domestic Assistance Numbers 59002 and...

Roles of reaction kinetics of CO 2 on a PrBaCo 2O 5.5+δ surfaces

DOE PAGES

Xu, Xing; Mace, Brennan; Enriquez, Erik; ...

2017-08-18

A symmetric PBCO/YSZ/PBCO cell (where PBCO refers to PrBaCo 2O 5.5+δ, and YSZ to yttria stabilized zirconia) was designed and fabricated for the investigation of the catalytic nature and reaction kinetics of CO 2 on PBCO surfaces. The electrochemical impedance spectroscopy was employed to probe the CO 2 reaction behavior on the PBCO electrode. The symmetric equivalent circuit cell characterization reveals that the surface resistance of CO 2 on PBCO is only 30.2 Ω cm 2 and the maximum surface exchange coefficient k chem is 2.0 × 10 -4 cm s -1 at 1147 K, suggesting that PBCO can bemore » an excellent candidate for CO 2 reduction.« less

Determination of cell cycle phases in live B16 melanoma cells using IRMS.

PubMed

Bedolla, Diana E; Kenig, Saša; Mitri, Elisa; Ferraris, Paolo; Marcello, Alessandro; Grenci, Gianluca; Vaccari, Lisa

2013-07-21

The knowledge of cell cycle phase distribution is of paramount importance for understanding cellular behaviour under normal and stressed growth conditions. This task is usually assessed using Flow Cytometry (FC) or immunohistochemistry. Here we report on the use of FTIR microspectroscopy in Microfluidic Devices (MD-IRMS) as an alternative technique for studying cell cycle distribution in live cells. Asynchronous, S- and G0-synchronized B16 mouse melanoma cells were studied by running parallel experiments based on MD-IRMS and FC using Propidium Iodide (PI) staining. MD-IRMS experiments have been done using silicon-modified BaF2 devices, where the thin silicon layer prevents BaF2 dissolution without affecting the transparency of the material and therefore enabling a better assessment of the Phosphate I (PhI) and II (PhII) bands. Hierarchical Cluster Analysis (HCA) of cellular microspectra in the 1300-1000 cm(-1) region pointed out a distribution of cells among clusters, which is in good agreement with FC results among G0/G1, S and G2/M phases. The differentiation is mostly driven by the intensity of PhI and PhII bands. In particular, PhI almost doubles from the G0/G1 to G2/M phase, in agreement with the trend followed by nucleic acids during cellular progression. MD-IRMS is then proposed as a powerful method for the in situ determination of the cell cycle stage of an individual cell, without any labelling or staining, which gives the advantage of possibly monitoring specific cellular responses to several types of stimuli by clearly separating the spectral signatures related to the cellular response from those of cells that are normally progressing.

Molecular cloning and functional characterization of the apple sucrose transporter gene MdSUT2.

PubMed

Ma, Qi-Jun; Sun, Mei-Hong; Liu, Ya-Jing; Lu, Jing; Hu, Da-Gang; Hao, Yu-Jin

2016-12-01

Sucrose is not only the primary photosynthetic product but also the major component translocated in the phloem of economically important plant species. Sucrose transporters or carriers (SUTs or SUCs), function as sucrose/H + symporters and play a crucial role in determining the cell-to-cell distribution of sucrose throughout the entire plant. However, whether such genes are involved in responses to abiotic stress and other biological processes is largely unknown. Here, we report that MdSUT2 in apple is a homolog of the Arabidopsis vacuolar sucrose transporter AtSUT2. Ectopic expression of MdSUT2 in Arabidopsis decreased sucrose sensitivity in germination and seeding stage and increased sucrose transport activity. In addition, our results showed that MdSUT2 impacted on plant growth by accelerating vegetative growth and promoting early flowering in Arabidopsis. Overexpression of MdSUT2 significantly improved abiotic stress tolerance including NaCl, ABA, and mannitol in apple calli and Arabidopsis. Together, these findings provide evidence that the apple sucrose transporter MdSUT2 is involved in abiotic stress resistance and the regulation of plant growth and development. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Tuning the giant magnetoelastic transition in Ba3BiIr2O9 and Ba3BiRu2O9.

PubMed

Huang, Zixin; Avdeev, Maxim; Kennedy, Brendan J; Knight, Kevin S; Zhou, Qingdi; Ling, Chris D

2014-07-09

We have experimentally investigated the effects of pressure on the magnetoelastic transitions associated with the opening of spin-gaps in Ba3BiIr2O9 and Ba3BiRu2O9. For both compounds, reducing the unit cell volume by either external physical and internal chemical pressure was found to reduce the temperature T(*) of the transition and, to a lesser extent, the magnitude of the associated negative thermal volume expansion. The results yield the latent heat associated with the transitions, -3.34(3) × 10(2) J mol(-1) for Ba3BiIr2O9 and -7.1(5) × 10(2) J mol(-1) for Ba3BiRu2O9. The transition in Ba3BiRu2O9 is significantly more robust than in Ba3BiIr2O9, requiring an order of magnitude higher pressures to achieve the same reduction in T(*). The differing responses of the two compounds points to differences between the 4d and 5d metals and hence to the importance of spin-orbit coupling, which is expected to be much stronger in the Ir compound.

A Mathematic Model That Describes Modes of MdSGHV Transmission within House Fly Populations.

PubMed

Vallejo, Celeste R; Lee, Jo Ann; Keesling, James E; Geden, Christopher J; Lietze, Verena-Ulrike; Boucias, Drion G

2013-11-20

In this paper it is proposed that one potential component by which the Musca domestica salivary gland hypertrophy virus (MdSGHV) infects individual flies is through cuticular damage. Breaks in the cuticle allow entry of the virus into the hemocoel causing the infection. Male flies typically have a higher rate of infection and a higher rate of cuticular damage than females. A model for the transmission of MdSGHV was formulated assuming several potential and recognized means of transmission. The model yields results that are in agreement with field data that measured the infection rate in house flies on dairy farms in Florida. The results from this model indicate that MdSGHV will be maintained at a stable rate within house fly populations and support the future use of MdSGHV as a birth control agent in house fly management.

Cross-sectional-derived determinants of satisfaction with physician-scientist training among Canadian MD/PhD graduates.

PubMed

Twa, David D W; Skinnider, Michael A; Squair, Jordan W; Lukac, Christine D

2017-01-01

Although MD/PhD programs require considerable commitment on behalf of students and learning institutions, they serve as an integral means of training future physician-scientists; individuals who engage in translational medicine. As attrition from these programs has longstanding effects on the community of translational medicine and comes at substantial cost to MD/PhD programs, we aimed to identify determinants that were associated with satisfaction among MD/PhD graduates, a feature that might inform on limiting program attrition. Anonymized data from a national survey of 139 Canadian MD/PhD alumni was analyzed. Factor analysis was conducted to evaluate the reliability of three questions that measured satisfaction and logistic regression was used to assess the association of outcomes with 17 independent determinants. Eighty-one percent of graduates were satisfied with MD/PhD training. Factor analysis confirmed the reliability of the questions measuring satisfaction. Determinants of self-reported satisfaction with physician-scientist training included co-authorship of more than six manuscripts during MD/PhD training. Additionally, protected research time at the place of current appointment was strongly associated with agreement that MD/PhD training had helped career progression. Demographic variables were not associated with any satisfaction indicator. Taken together, the majority of Canadian MD/PhD graduates are satisfied with their physician-scientist training. Project collaboration leading to co-authorships and protected research time were strongly associated with training satisfaction among graduates. If the value of collaboration can be realized among current and future physician-scientist trainees who are dissatisfied with their training, this might ultimately reduce program attrition.

Frequency of a natural truncated allele of MdMLO19 in the germplasm of Malus domestica.

PubMed

Pessina, Stefano; Palmieri, Luisa; Bianco, Luca; Gassmann, Jennifer; van de Weg, Eric; Visser, Richard G F; Magnago, Pierluigi; Schouten, Henk J; Bai, Yuling; Riccardo Velasco, R; Malnoy, Mickael

2017-01-01

Podosphaera leucotricha is the causal agent of powdery mildew (PM) in apple. To reduce the amount of fungicides required to control this pathogen, the development of resistant apple cultivars should become a priority. Resistance to PM was achieved in various crops by knocking out specific members of the MLO gene family that are responsible for PM susceptibility (S-genes). In apple, the knockdown of MdMLO19 resulted in PM resistance. However, since gene silencing technologies such as RNAi are perceived unfavorably in Europe, a different approach that exploits this type of resistance is needed. This work evaluates the presence of non-functional naturally occurring alleles of MdMLO19 in apple germplasm. The screening of the re-sequencing data of 63 apple individuals led to the identification of 627 single nucleotide polymorphisms (SNPs) in five MLO genes ( MdMLO5, MdMLO7, MdMLO11, MdMLO18 , and MdMLO19 ), 127 of which were located in exons. The T-1201 insertion of a single nucleotide in MdMLO19 caused the formation of an early stop codon, resulting in a truncated protein lacking 185 amino acids, including the calmodulin-binding domain. The presence of the insertion was evaluated in 115 individuals. It was heterozygous in 64 and homozygous in 25. Twelve of the 25 individuals carrying the insertion in homozygosity were susceptible to PM. After barley, pea, cucumber, and tomato, apple would be the fifth species for which a natural non-functional mlo allele has been found.

Structure and Electrical-Transport Relations in Ba(Zr,Pr)O3-δ Perovskites.

PubMed

Antunes, Isabel; Amador, Ulises; Alves, Adriana; Correia, Maria Rosário; Ritter, Clemens; Frade, Jorge Ribeiro; Pérez-Coll, Domingo; Mather, Glenn C; Fagg, Duncan Paul

2017-08-07

Members of the perovskite solid solution BaZr 1-x Pr x O 3-δ (0.2 ≤ x ≤ 0.8) with potential high-temperature electrochemical applications were synthesized via mechanical activation and high-temperature annealing at 1250 °C. Structural properties were examined by Rietveld analysis of neutron powder diffraction and Raman spectroscopy at room temperature, indicating rhombohedral symmetry (space group R3̅c) for members x = 0.2 and 0.4 and orthorhombic symmetry (Imma) for x = 0.6 and 0.8. The sequence of phase transitions for the complete solid solution from BaZrO 3 to BaPrO 3 is Pm3̅m → R3̅c → Imma → Pnma. The structural data indicate that Pr principally exists as Pr 4+ on the B site and that oxygen content increases with higher Pr content. Electrical-conductivity measurements in the temperature range of 250-900 °C in dry and humidified (pH 2 O ≈ 0.03 atm) N 2 and O 2 atmospheres revealed an increase of total conductivity by over 2 orders of magnitude in dry conditions from x = 0.2 to x = 0.8 (σ ≈ 0.08 S cm -1 at 920 °C in dry O 2 for x = 0.8). The conductivity for Pr contents x > 0.2 is attributable to positively charged electronic carriers, whereas for x = 0.2 transport in dry conditions is n-type. The change in conduction mechanism with composition is proposed to arise from the compensation regime for minor amounts of BaO loss changing from predominantly partitioning of Pr on the A site to vacancy formation with increasing Pr content. Conductivity is lower in wet conditions for x > 0.2 indicating that the positive defects are, to a large extent, charge compensated by less mobile protonic species. In contrast, the transport mechanism of the Zr-rich composition (x = 0.2), with much lower electronic conductivity, is essentially independent of moisture content.

High resolution Fourier transform spectroscopy and crystal-field analysis in Tm,Ho:BaY2F8

NASA Astrophysics Data System (ADS)

Baraldi, A.; Capelletti, R.; Mazzera, M.; Riolo, P.; Amoretti, G.; Magnani, N.; Sani, E.; Toncelli, A.; Tonelli, M.

2005-01-01

A Tm3+- Ho3+ -codoped single crystal of monoclinic BaY2F8 has been characterized by means of high resolution FTIR spectroscopy in the wave number range 2000-24000 cm-1 and in the temperature range 9-300 K. The energy level schemes of the two lanthanide ions as determined by the optical absorption spectra is presented, analyzed, and fitted within a single ion Hamiltonian model. The very small energy separation (about 0.6-1.6 cm-1) measured between the first and second sublevels of the ground state manifolds for both the ions is in line with the theoretical predictions. The impurity-phonon coupling is put into evidence by the thermally induced line shift and broadening, and by the detection of vibronic replicas of a few lines.

The R2R3-MYB transcription factor MdMYB73 is involved in malate accumulation and vacuolar acidification in apple.

PubMed

Hu, Da-Gang; Li, Yuan-Yuan; Zhang, Quan-Yan; Li, Ming; Sun, Cui-Hui; Yu, Jian-Qiang; Hao, Yu-Jin

2017-08-01

Malate, the predominant organic acid in many fruits, is a crucial component of the organoleptic quality of fruit, including taste and flavor. The genetic and environmental mechanisms affecting malate metabolism in fruit cells have been studied extensively. However, the transcriptional regulation of malate-metabolizing enzymes and vacuolar transporters remains poorly understood. Our previous studies demonstrated that MdMYB1 modulates anthocyanin accumulation and vacuolar acidification by directly activating vacuolar transporters, including MdVHA-B1, MdVHA-E, MdVHP1 and MdtDT. Interestingly, we isolated and identified a MYB transcription factor, MdMYB73, a distant relative of MdMYB1 in this study. It was subsequently found that MdMYB73 protein bound directly to the promoters of MdALMT9 (aluminum-activated malate transporter 9), MdVHA-A (vacuolar ATPase subunit A) and MdVHP1 (vacuolar pyrophosphatase 1), transcriptionally activating their expression and thereby enhancing their activities. Analyses of transgenic apple calli demonstrated that MdMYB73 influenced malate accumulation and vacuolar pH. Furthermore, MdCIbHLH1 interacted with MdMYB73 and enhanced its activity upon downstream target genes. These findings help to elucidate how MdMYB73 directly modulates the vacuolar transport system to affect malate accumulation and vacuolar pH in apple. © 2017 The Authors The Plant Journal © 2017 John Wiley & Sons Ltd.

First-principles study of (Ba ,Ca ) TiO3 and Ba (Ti ,Zr ) O3 solid solutions

NASA Astrophysics Data System (ADS)

Amoroso, Danila; Cano, Andrés; Ghosez, Philippe

2018-05-01

(Ba ,Ca ) TiO3 and Ba (Ti ,Zr ) O3 solid solutions are the building blocks of lead-free piezoelectric materials that attract a renewed interest. We investigate the properties of these systems by means of first-principles calculations, with a focus on the lattice dynamics and the competition between different ferroelectric phases. We first analyze the four parent compounds in order to compare their properties and their different tendency towards ferroelectricity. The core of our study is systematic characterization of the binary systems (Ba ,Ca ) TiO3 and Ba (Ti ,Zr ) O3 within both the virtual crystal approximation and direct supercell calculations. In the case of Ca doping, we find a gradual transformation from B -site to A -site ferroelectricity due to steric effects that largely determines the behavior of the system. In the case of Zr doping, in contrast, the behavior is eventually dominated by cooperative Zr-Ti motions and the local electrostatics. In addition, our comparative study reveals that the specific microscopic physics of these solids sets severe limits to the applicability of the virtual crystal approximation for these systems.

Multi-wavelength picosecond BaWO4 Raman laser with long and short Raman shifts and 12-fold pulse shortening down to 3 ps at 1227 nm

NASA Astrophysics Data System (ADS)

Frank, M.; Jelínek, M., Jr.; Vyhlídal, D.; Kubeček, V.; Ivleva, L. I.; Zverev, P. G.; Smetanin, S. N.

2018-02-01

In this paper, we demonstrate the generation of three (1179, 1227, and 1323 nm) Stokes components of stimulated Raman scattering with long (925 cm-1 ) and short (332 cm-1 ) Raman shifts in an all-solid-state, synchronously pumped, extra-cavity Raman laser based on a BaWO4 crystal excited by a quasi-continuous, 36 ps, diode side-pumped Nd:GdVO4 laser generating at the wavelength of 1063 nm. We achieved the strongest 12-fold pulse shortening down to 3 ps at the 925 cm-1   +  332 cm-1 shifted 1227 nm wavelength due to a shorter dephasing time (wider linewidth) of the short-shift 332 cm-1 Raman line, resulting in a peak power of 2.5 kW.

78 FR 3496 - Maryland Disaster Number MD-00025

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-16

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13394 and 13395] Maryland Disaster Number MD-00025 AGENCY: U.S. Small Business Administration. ACTION: Amendment 3. SUMMARY: This is an amendment of.... (Catalog of Federal Domestic Assistance Numbers 59002 and 59008) James E. Rivera, Associate Administrator...

76 FR 70528 - Maryland Disaster Number MD-00018

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-14

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 12874 and 12875] Maryland Disaster Number MD-00018 AGENCY: U.S. Small Business Administration. ACTION: Amendment 2. SUMMARY: This is an amendment of... declaration remains unchanged. (Catalog of Federal Domestic Assistance Numbers 59002 and 59008) James E...

77 FR 74908 - Maryland Disaster Number MD-00025

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-18

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13394 and 13395] Maryland Disaster Number MD-00025 AGENCY: U.S. Small Business Administration. ACTION: Amendment 1. SUMMARY: This is an amendment of... declaration remains unchanged. (Catalog of Federal Domestic Assistance Numbers 59002 and 59008) James E...

High-pressure synthesis of the cubic perovskite BaRuO3 and evolution of ferromagnetism in ARuO3 (A = Ca, Sr, Ba) ruthenates.

PubMed

Jin, C-Q; Zhou, J-S; Goodenough, J B; Liu, Q Q; Zhao, J G; Yang, L X; Yu, Y; Yu, R C; Katsura, T; Shatskiy, A; Ito, E

2008-05-20

The cubic perovskite BaRuO(3) has been synthesized under 18 GPa at 1,000 degrees C. Rietveld refinement indicates that the new compound has a stretched Ru-O bond. The cubic perovskite BaRuO(3) remains metallic to 4 K and exhibits a ferromagnetic transition at T(c) = 60 K, which is significantly lower than the T(c) approximately = 160 K for SrRuO(3). The availability of cubic perovskite BaRuO(3) not only makes it possible to map out the evolution of magnetism in the whole series of ARuO(3) (A = Ca, Sr, Ba) as a function of the ionic size of the A-site r(A,) but also completes the polytypes of BaRuO(3). Extension of the plot of T(c) versus r(A) in perovskites ARuO(3) (A = Ca, Sr, Ba) shows that T(c) does not increase as the cubic structure is approached, but has a maximum for orthorhombic SrRuO(3). Suppressing T(c) by Ca and Ba doping in SrRuO(3) is distinguished by sharply different magnetic susceptibilities chi(T) of the paramagnetic phase. This distinction has been interpreted in the context of a Griffiths' phase on the (Ca Sr)RuO(3) side and bandwidth broadening on the (Sr,Ba)RuO(3) side.

High-pressure synthesis of the cubic perovskite BaRuO3 and evolution of ferromagnetism in ARuO3 (A = Ca, Sr, Ba) ruthenates

PubMed Central

Jin, C.-Q.; Zhou, J.-S.; Goodenough, J. B.; Liu, Q. Q.; Zhao, J. G.; Yang, L. X.; Yu, Y.; Yu, R. C.; Katsura, T.; Shatskiy, A.; Ito, E.

2008-01-01

The cubic perovskite BaRuO3 has been synthesized under 18 GPa at 1,000°C. Rietveld refinement indicates that the new compound has a stretched Ru–O bond. The cubic perovskite BaRuO3 remains metallic to 4 K and exhibits a ferromagnetic transition at Tc = 60 K, which is significantly lower than the Tc ≈ 160 K for SrRuO3. The availability of cubic perovskite BaRuO3 not only makes it possible to map out the evolution of magnetism in the whole series of ARuO3 (A = Ca, Sr, Ba) as a function of the ionic size of the A-site rA, but also completes the polytypes of BaRuO3. Extension of the plot of Tc versus rA in perovskites ARuO3 (A = Ca, Sr, Ba) shows that Tc does not increase as the cubic structure is approached, but has a maximum for orthorhombic SrRuO3. Suppressing Tc by Ca and Ba doping in SrRuO3 is distinguished by sharply different magnetic susceptibilities χ(T) of the paramagnetic phase. This distinction has been interpreted in the context of a Griffiths' phase on the (Ca Sr)RuO3 side and bandwidth broadening on the (Sr,Ba)RuO3 side. PMID:18480262

Preparation of LTCC materials with adjustable permittivity based on BaO–B{sub 2}O{sub 3}–SiO{sub 2}/BaTiO{sub 3} system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Kai-tuo; He, Yan; Liang, Zhong-yuan

2015-05-15

Graphical abstract: The dielectric constant (ϵ) of the sintered BaO–B{sub 2}O{sub 3}–SiO{sub 2}/BaTiO{sub 3} glass/ceramics (the sintered samples with line shrinkage of 10%) changed from 5 to 30 and the dielectric losses (tanδ) was lower than 0.05 at 100 MHz with the amount of BaTiO{sub 3} additive increment from 60 wt% to 90 wt% fraction. - Highlights: • The ϵ of BaO–B{sub 2}O{sub 3}–SiO{sub 2} glass can be adjusted from 5 to 30 by adding BaTiO{sub 3}. • The influence factors on dielectric are the secondary phase and microstructure. • BaO–B{sub 2}O{sub 3}–SiO{sub 2}/BaTiO{sub 3} system can fabricate LTCC whenmore » BaTiO{sub 3} located in 60–80 wt%. - Abstract: This paper studied the preparation and characterization of LTCC (low temperature co-fired ceramics) materials based on BaO–B{sub 2}O{sub 3}–SiO{sub 2}/BaTiO{sub 3} glass–ceramics, where the sintering temperature was about 900 °C and dielectric constant was effectively adjustable from 5 to 30 by changing the BaTiO{sub 3} fraction from 60 wt% to 90 wt%. X-ray diffractometer (XRD), scanning electron microscopy (SEM) were used to examine the effect of different amounts additive on the dielectric properties of this LTCC system and the crystal structure change. The results indicated that BaTiO{sub 3} can be used as a dielectric additive aim to adjust the permittivity of BaO–B{sub 2}O{sub 3}–SiO{sub 2} glass, which the main influence factors on dielectric are the contents of the secondary phase, the BaTiO{sub 3} phase fraction and the porous structure of the sintered body. Therefore, the microstructure and dielectric property of BaO–B{sub 2}O{sub 3}–SiO{sub 2}/BaTiO{sub 3} glass–ceramics composites could be controlled by adjusting the content of BaTiO{sub 3} additive.« less

Eva Szabo, MD | Division of Cancer Prevention

Cancer.gov

Dr. Eva Szabo is Chief of the Lung and Upper Aerodigestive Cancer Research Group at the NCI Division of Cancer Prevention. She graduated from Yale University with a BS in Molecular Biophysics and Biochemistry, received her MD from Duke University, and completed her internal medicine residency at Bellevue-NYU Medical Center. After completing her medical oncology fellowship at

Species-Specific Activation of TLR4 by Hypoacylated Endotoxins Governed by Residues 82 and 122 of MD-2

PubMed Central

Oblak, Alja; Jerala, Roman

2014-01-01

The Toll-like receptor 4/MD-2 receptor complex recognizes endotoxin, a Gram-negative bacterial cell envelope component. Recognition of the most potent hexaacylated form of endotoxin is mediated by the sixth acyl chain that protrudes from the MD-2 hydrophobic pocket and bridges TLR4/MD-2 to the neighboring TLR4 ectodomain, driving receptor dimerization via hydrophobic interactions. In hypoacylated endotoxins all acyl chains could be accommodated within the binding pocket of the human hMD-2. Nevertheless, tetra- and pentaacylated endotoxins activate the TLR4/MD-2 receptor of several species. We observed that amino acid residues 82 and 122, located at the entrance to the endotoxin binding site of MD-2, have major influence on the species-specific endotoxin recognition. We show that substitution of hMD-2 residue V82 with an amino acid residue with a bulkier hydrophobic side chain enables activation of TLR4/MD-2 by pentaacylated and tetraacylated endotoxins. Interaction of the lipid A phosphate group with the amino acid residue 122 of MD-2 facilitates the appropriate positioning of the hypoacylated endotoxin. Moreover, mouse TLR4 contributes to the agonistic effect of pentaacylated msbB endotoxin. We propose a molecular model that explains how the molecular differences between the murine or equine MD-2, which both have sufficiently large hydrophobic pockets to accommodate all five or four acyl chains, influence the positioning of endotoxin so that one of the acyl chains remains outside the pocket and enables hydrophobic interactions with TLR4, leading to receptor activation. PMID:25203747

Species-specific activation of TLR4 by hypoacylated endotoxins governed by residues 82 and 122 of MD-2.

PubMed

Oblak, Alja; Jerala, Roman

2014-01-01

The Toll-like receptor 4/MD-2 receptor complex recognizes endotoxin, a Gram-negative bacterial cell envelope component. Recognition of the most potent hexaacylated form of endotoxin is mediated by the sixth acyl chain that protrudes from the MD-2 hydrophobic pocket and bridges TLR4/MD-2 to the neighboring TLR4 ectodomain, driving receptor dimerization via hydrophobic interactions. In hypoacylated endotoxins all acyl chains could be accommodated within the binding pocket of the human hMD-2. Nevertheless, tetra- and pentaacylated endotoxins activate the TLR4/MD-2 receptor of several species. We observed that amino acid residues 82 and 122, located at the entrance to the endotoxin binding site of MD-2, have major influence on the species-specific endotoxin recognition. We show that substitution of hMD-2 residue V82 with an amino acid residue with a bulkier hydrophobic side chain enables activation of TLR4/MD-2 by pentaacylated and tetraacylated endotoxins. Interaction of the lipid A phosphate group with the amino acid residue 122 of MD-2 facilitates the appropriate positioning of the hypoacylated endotoxin. Moreover, mouse TLR4 contributes to the agonistic effect of pentaacylated msbB endotoxin. We propose a molecular model that explains how the molecular differences between the murine or equine MD-2, which both have sufficiently large hydrophobic pockets to accommodate all five or four acyl chains, influence the positioning of endotoxin so that one of the acyl chains remains outside the pocket and enables hydrophobic interactions with TLR4, leading to receptor activation.

Antiferromagnetic structure and electronic properties of BaCr2As2 and BaCrFeAs2

NASA Astrophysics Data System (ADS)

Filsinger, Kai A.; Schnelle, Walter; Adler, Peter; Fecher, Gerhard H.; Reehuis, Manfred; Hoser, Andreas; Hoffmann, Jens-Uwe; Werner, Peter; Greenblatt, Martha; Felser, Claudia

2017-05-01

Recent theoretical studies suggest that superconductivity may be found in doped chromium pnictides with crystal structures similar to their iron counterparts. Here, we report a comprehensive study on the magnetic arsenides BaCr2As2 and BaCrFeAs2 (space group I 4 /m m m ), which are possible mother compounds with d4 and d5 electron configurations, respectively. DFT-based calculations of the electronic structure evidence metallic antiferromagnetic ground states for both compounds. By powder neutron diffraction, we confirm for BaCr2As2 a robust ordering in the antiferromagnetic G -type structure at TN=580 K with μCr=1.9 μB . Anomalies in the lattice parameters point to magnetostructural coupling effects. In BaCrFeAs2, the Cr and Fe atoms randomly occupy the transition-metal site and G -type order is found below 265 K with μCr /Fe=1.1 μB . 57Fe Mössbauer spectroscopy demonstrates that only a small ordered moment is associated with the Fe atoms, in agreement with electronic structure calculations leading to μFe˜0 . The temperature dependence of the hyperfine field does not follow that of the total moments. Both compounds are metallic but show large enhancements of the linear specific heat. Electrical transport in BaCrFeAs2 is dominated by the atomic disorder and the partial magnetic disorder of Fe. Our results indicate that Néel-type order is unfavorable for Fe moments and thus it is destabilized with increasing Fe content.

Ensemble MD simulations restrained via crystallographic data: Accurate structure leads to accurate dynamics

PubMed Central

Xue, Yi; Skrynnikov, Nikolai R

2014-01-01

Currently, the best existing molecular dynamics (MD) force fields cannot accurately reproduce the global free-energy minimum which realizes the experimental protein structure. As a result, long MD trajectories tend to drift away from the starting coordinates (e.g., crystallographic structures). To address this problem, we have devised a new simulation strategy aimed at protein crystals. An MD simulation of protein crystal is essentially an ensemble simulation involving multiple protein molecules in a crystal unit cell (or a block of unit cells). To ensure that average protein coordinates remain correct during the simulation, we introduced crystallography-based restraints into the MD protocol. Because these restraints are aimed at the ensemble-average structure, they have only minimal impact on conformational dynamics of the individual protein molecules. So long as the average structure remains reasonable, the proteins move in a native-like fashion as dictated by the original force field. To validate this approach, we have used the data from solid-state NMR spectroscopy, which is the orthogonal experimental technique uniquely sensitive to protein local dynamics. The new method has been tested on the well-established model protein, ubiquitin. The ensemble-restrained MD simulations produced lower crystallographic R factors than conventional simulations; they also led to more accurate predictions for crystallographic temperature factors, solid-state chemical shifts, and backbone order parameters. The predictions for 15N R1 relaxation rates are at least as accurate as those obtained from conventional simulations. Taken together, these results suggest that the presented trajectories may be among the most realistic protein MD simulations ever reported. In this context, the ensemble restraints based on high-resolution crystallographic data can be viewed as protein-specific empirical corrections to the standard force fields. PMID:24452989

Strain induced optical properties of BaReO3

NASA Astrophysics Data System (ADS)

Kumavat, Sandip R.; Kansara, Shivam; Gupta, Sanjeev K.; Sonvane, Yogesh

2018-05-01

Here, we have performed strain induce optical properties of BaReO3 by using density functional theory (DFT). We noticed that after applying intrinsic and extrinsic strain to the BaReO3, it shows the metallic behavior. We also studied optical properties, which show good activity in the ultraviolet region. The results show that after applying intrinsic and extrinsic strain to BaReO3 the absorption peaks are shifted towards the high UV region of the spectrum. Thus, we concluded that, BaReO3 material with extrinsic strain can be useful for high frequency UV device and optoelectronic devices.

Multiple Simulated Annealing-Molecular Dynamics (MSA-MD) for Conformational Space Search of Peptide and Miniprotein

PubMed Central

Hao, Ge-Fei; Xu, Wei-Fang; Yang, Sheng-Gang; Yang, Guang-Fu

2015-01-01

Protein and peptide structure predictions are of paramount importance for understanding their functions, as well as the interactions with other molecules. However, the use of molecular simulation techniques to directly predict the peptide structure from the primary amino acid sequence is always hindered by the rough topology of the conformational space and the limited simulation time scale. We developed here a new strategy, named Multiple Simulated Annealing-Molecular Dynamics (MSA-MD) to identify the native states of a peptide and miniprotein. A cluster of near native structures could be obtained by using the MSA-MD method, which turned out to be significantly more efficient in reaching the native structure compared to continuous MD and conventional SA-MD simulation. PMID:26492886

Absorption spectroscopy of heavy alkaline earth metals Ba and Sr in rare gas matrices—CCSD(T) calculations and atomic site occupancies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, Barry M.; McCaffrey, John G., E-mail: john.mccaffrey@nuim.ie

2016-01-28

Isolation of the heavier alkaline earth metals Ba and Sr in the solid rare gases (RGs) Ar, Kr, and Xe is analysed with absorption spectroscopy and interpreted partly with the assistance of ab initio calculations of the diatomic M ⋅ RG ground state interaction potentials. The y{sup 1}P←a{sup 1}S resonance transitions in the visible spectral region are used to compare the isolation conditions of these two metal atom systems and calcium. Complex absorption bands were recorded in all three metal atom systems even after extensive sample annealing. Coupled cluster calculations conducted on the ground states of the nine M ⋅more » RG diatomics (M = Ca, Sr, and Ba; RG = Ar, Kr, and Xe) at the coupled cluster single, double, and non-iterative triple level of theory revealed long bond lengths (>5 Å) and shallow bound regions (<130 cm{sup −1}). All of the M ⋅ RG diatomics have bond lengths considerably longer than those of the rare gas dimers, with the consequence that isolation of these metal atoms in a single substitutional site of the solid rare gas is unlikely, with the possible exception of Ca/Xe. The luminescence of metal dimer bands has been recorded for Ba and Sr revealing very different behaviours. Resonance fluorescence with a lifetime of 15 ns is observed for the lowest energy transition of Sr{sub 2} while this transition is quenched in Ba{sub 2}. This behaviour is consistent with the absence of vibrational structure on the dimer absorption band in Ba{sub 2} indicating lifetime broadening arising from efficient relaxation to low-lying molecular states. More extensive 2D excitation-emission data recorded for the complex site structures present on the absorption bands of the atomic Ba and Sr systems will be presented in future publications.« less

Strong anisotropy of electric field effects on uniaxial relaxor ferroelectric Sr0.75Ba0.25Nb2O6 crystals proved by acoustic emission

NASA Astrophysics Data System (ADS)

Dul'kin, E.; Kojima, S.; Roth, M.

2018-01-01

[001] oriented Sr0.75Ba0.25Nb2O6 uniaxial relaxor ferroelectric crystals have been studied by acoustic emission in the temperature range of 20÷200 °C and under an external electric field up to 1 kV/cm. Under the application of an electric field the temperature of a dielectric maximum exhibits a nontrivial behavior: it remains constant at first, secondly steep decreases down to some threshold field, and thirdly starts to increase as a field enhances, whereas the same temperature of a dielectric maximum under a bias electric field to [100] oriented Sr0.75Ba0.25Nb2O6 crystals exhibits a smoothed minimum before the start to increase as a field enhances (E. Dul'kin et al., J. Appl. Phys. 110, 044106 (2011)). Such a difference of electric field effects in c- and a-cut crystals is discussed from the viewpoint of random-bond-random-field model of relaxor ferroelectrics. By the comparison between experimental and theoretical data, a dipole moment of the PNR was estimated to be 0.1 (C cm).

Genome-wide histone modification profile induced by MDV in MD-resistant and -susceptible chickens

USDA-ARS?s Scientific Manuscript database

Marek’s disease (MD) is a lymphoproliferative disease in chicken caused by oncogenic Marek’s disease virus (MDV). MD is characterized by infiltration of proliferating lymphoid cells in organs, such as peripheral nerve, skin, muscle, liver, spleen, heart, kidney, gonads and proventriculus. Epigenetic...

Molecular recognition at methyl methacrylate/n-butyl acrylate (MMA/nBA) monomer unit boundaries of phospholipids at p-MMA/nBA copolymer surfaces.

PubMed

Yu, Min; Urban, Marek W; Sheng, Yinghong; Leszczynski, Jerzy

2008-09-16

Lipid structural features and their interactions with proteins provide a useful vehicle for further advances in membrane proteins research. To mimic one of potential lipid-protein interactions we synthesized poly(methyl methacrylate/ n-butyl acrylate) (p-MMA/nBA) colloidal particles that were stabilized by phospholipid (PLs). Upon the particle coalescence, PL stratification resulted in the formation of surface localized ionic clusters (SLICs). These entities are capable of recognizing MMA/nBA monomer interfaces along the p-MMA/nBA copolymer backbone and form crystalline SLICs at the monomer interface. By utilizing attenuated total reflectance Fourier transform infrared (ATR FT-IR) spectroscopy and selected area electron diffraction (SAD) combined with ab initio calculations, studies were conducted that identified the origin of SLICs as well as their structural features formed on the surface of p-MMA/nBA copolymer films stabilized by 1,2-dilauroyl-sn-glycero-3-phosphocholine (DLPC) PL. Specific entities responsible for SLIC formation are selective noncovalent bonds of anionic phosphate and cationic quaternary ammonium segments of DLPC that interact with two neighboring carbonyl groups of nBA and MMA monomers of the p-MMA/nBA polymer backbone. To the best of our knowledge this is the first example of molecular recognition facilitated by coalescence of copolymer colloidal particles and the ability of PLs to form SLICs at the boundaries of the neighboring MMA and nBA monomer units of the p-MMA/nBA chain. The dominating noncovalent bonds responsible for the molecular recognition is a combination of H-bonding and electrostatic interactions.

Thomas Secker M.D.: Archbishop and man-midwife.

PubMed

Morgan-Guy, John

2018-05-01

This paper provides a biographical outline of the career of Thomas Secker, MD, who from 1758-68 was Archbishop of Canterbury. Although much has been written on Secker, this study seeks to highlight his training in medicine, which has been largely overlooked hitherto by historians.

David Kasner, MD, and the Road to Pars Plana Vitrectomy

PubMed Central

Blodi, Christopher F.

2016-01-01

David Kasner, MD (1927–2001), used his extensive dissections of eye bank eyes and experiences in teaching cataract surgery to resident physicians to realize that excision of vitreous when present in the anterior chamber of eyes undergoing cataract surgery was preferable to prior intraoperative procedures. Noting that eyes tolerated his maneuvers, he then performed planned subtotal open-sky vitrectomies; first on a traumatized eye in 1961, then on two eyes of patients with amyloidosis (1966–1967). The success of these operations was noted by others, most particularly Robert Machemer, MD. Kasner’s work directly led to further surgical developments, including closed pars plana vitrectomy. PMID:27660504

Humanized TLR4/MD-2 mice reveal LPS recognition differentially impacts susceptibility to Yersinia pestis and Salmonella enterica.

PubMed

Hajjar, Adeline M; Ernst, Robert K; Fortuno, Edgardo S; Brasfield, Alicia S; Yam, Cathy S; Newlon, Lindsay A; Kollmann, Tobias R; Miller, Samuel I; Wilson, Christopher B

2012-01-01

Although lipopolysaccharide (LPS) stimulation through the Toll-like receptor (TLR)-4/MD-2 receptor complex activates host defense against Gram-negative bacterial pathogens, how species-specific differences in LPS recognition impact host defense remains undefined. Herein, we establish how temperature dependent shifts in the lipid A of Yersinia pestis LPS that differentially impact recognition by mouse versus human TLR4/MD-2 dictate infection susceptibility. When grown at 37°C, Y. pestis LPS is hypo-acylated and less stimulatory to human compared with murine TLR4/MD-2. By contrast, when grown at reduced temperatures, Y. pestis LPS is more acylated, and stimulates cells equally via human and mouse TLR4/MD-2. To investigate how these temperature dependent shifts in LPS impact infection susceptibility, transgenic mice expressing human rather than mouse TLR4/MD-2 were generated. We found the increased susceptibility to Y. pestis for "humanized" TLR4/MD-2 mice directly paralleled blunted inflammatory cytokine production in response to stimulation with purified LPS. By contrast, for other Gram-negative pathogens with highly acylated lipid A including Salmonella enterica or Escherichia coli, infection susceptibility and the response after stimulation with LPS were indistinguishable between mice expressing human or mouse TLR4/MD-2. Thus, Y. pestis exploits temperature-dependent shifts in LPS acylation to selectively evade recognition by human TLR4/MD-2 uncovered with "humanized" TLR4/MD-2 transgenic mice.

THERMAL AND ELECTRICAL PROPERTIES OF Ba0.5Sr0.5CoxFe1-x-yNiyO3-δ (x = 0.4, 0 ≤ y ≤ 0.25) AS CATHODE MATERIAL FOR IT-SOFCs

NASA Astrophysics Data System (ADS)

Burnwal, Suman Kumar; Kistaiah, P.

2015-03-01

Ba0.5Sr0.5CoxFe1-x-yNiyO3-δ (BSCFNi; x = 0.4, 0 ≤ y ≤ 0.25) were studied in relation to their potential use as intermediate temperature solid oxide fuel cell (IT-SOFC) cathode. An emphasis is made on the effect of Ni-doping on crystal structure, thermal expansion coefficient (TEC) and dc electrical conductivity. A cubic perovskite structure was observed in the X-ray diffraction (XRD) measurement. The TEC of BSCFNi obtained for 0 ≤ y ≤ 0.25, varies in the range of (12.38-18.81) × 10-6 K-1, measured in the temperature range of 30°C to 800°C. The electrical conductivity which is a major defect of Ba0.5Sr0.5CoxFe1-xO3-δ (BSCF) was improved by Ni-doping. The compound with y = 0.20 and 0.25 demonstrated a conductivity of σ = 62.59 S-cm-1 and 72.64 S-cm-1 at 400°C and 77.01 S-cm-1 and 89.68 S-cm-1 at 500°C.

ESR and nonresonant microwave absorption of ErBa2Cu3O(7-delta) and HoBa2Cu3O(7-delta) single crystals

NASA Astrophysics Data System (ADS)

Tagaya, Kimihito; Fukuoka, Nobuo; Nakanishi, Shigemitsu

1990-12-01

ESR measurements were performed for ErBa2Cu3O(7-delta) and HoBa2Cu3O(7-delta) single crystals from 77 K to room temperature. The ESR signals of Er2BaCuO5 and Ho2BaCuO5 were observed, and their temperature variations were investigated. Nonresonant microwave absorption was also observed below the superconducting critical temperature of 93 K. The principal values of lower critical field were determined.

A CIPK protein kinase targets sucrose transporter MdSUT2.2 at Ser254 for phosphorylation to enhance salt tolerance.

PubMed

Ma, Qi-Jun; Sun, Mei-Hong; Kang, Hui; Lu, Jing; You, Chun-Xiang; Hao, Yu-Jin

2018-05-23

Soil salinity is one of the major abiotic stressors that negatively affect crop growth and yield. Salt stress can regulate antioxidants and the accumulation of osmoprotectants. In the study, a sucrose transporter MdSUT2.2 was identified in apple. Overexpression of MdSUT2.2 gene increased salt tolerance in the transgenic apple, compared with the WT control 'Gala'. In addition, it was found that protein MdSUT2.2 was phosphorylated at Ser 254 site in response to salt. A DUAL membrane yeast hybridization system through an apple cDNA library demonstrated that a protein kinase MdCIPK13 interacted with MdSUT2.2. A series of transgenic analysis in apple calli showed that MdCIPK13 was required for the salt-induced phosphorylation of MdSUT2.2 protein and enhanced its stability and transport activity. Finally, it was found that MdCIPK13 improved salt resistance in an MdSUT2.2-dependent manner. These findings had enriched our understanding of the molecular mechanisms underlying abiotic stress. This article is protected by copyright. All rights reserved.

Synthesis and Thermodynamic Stability of Ba2B‧B″O6 and Ba3B*B″2O9 Perovskites Using the Molten Salt Method

NASA Astrophysics Data System (ADS)

Meng, Wei; Virkar, Anil V.

1999-12-01

A number of mixed perovskites of the types Ba2B‧B″O6 (BaB‧1/2B″1/2O3) and Ba3B*B″2O9 (BaB*1/3B″2/3O3) where B‧=Gd, La, Nd, Sm, or Y; B″=Nb and B*=Ca were synthesized by a conventional calcination process, as well as by the molten salt method. The former consists of calcining appropriate mixtures of oxide or carbonate precursors in air at elevated temperatures (∼1250°C). The latter method consists of adding appropriate mixtures of oxide or carbonate precursors to a molten salt bath at relatively low temperatures (on the order of 300 to 500°C) so that the requisite compound is formed by dissolution-reprecipitation. X-ray diffraction confirmed the formation of a single-phase perovskite in each case with calcination at 1250°C. In a molten salt bath, however, all except Ba2LaNbO6 and Ba2NdNbO6 formed the perovskite structure. On the contrary, powders of Ba2LaNbO6 and Ba2NdNbO6 formed by a high-temperature calcination process readily decomposed when introduced into the molten salt bath. The formation of the requisite perovskite at a temperature as low as 350°C in a molten salt suggests that: (a) The perovskite is stable at 350°C. (b) The molten salt exhibits sufficient precursor solubility for the dissolution-reprecipitation process to occur in a reasonable time. Similarly, the decomposition of Ba2LaNbO6 and Ba2NdNbO6 in a molten salt bath shows that these materials are thermodynamically unstable at the temperature of the molten salt bath.

Changing Morphology of BaO/AI₂O₃ during NO₂ Uptake and Release

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szanyi, Janos; Kwak, Ja Hun; Hanson, Jonathan

2005-04-21

The changes in the morphology of Ba-oxide-based NOx storage/reduction catalysts were investigated using time resolved x-ray diffraction, transmission electron microscopy and energy dispersed spectroscopy. Large Ba(NO₃)₂ crystallites form on the alumina support when the catalyst is prepared by the incipient wetness method using an aqueous Ba(NO₃)₂ solution. Heating the sample to 873K in a He flow results in the decomposition of the Ba(NO₃)₂ phase and the formation of both a monolayer BaO film strongly interacting with the alumina support, and nano crystalline BaO particles. Upon NO₂ exposure of these BaO phases at room temperature, small (nano-sized) Ba(NO₃)₂ crystals and amore » monolayer of surface nitrate form. Heating this sample in NO₂ results in the coalescence of the nano crystalline Ba(NO₃)₂ particles into large crystals. The average crystal size in the re-formed Ba(NO₃)₂ layer is significantly smaller than that measured after the catalyst preparation. Evidence is also presented for the existence of a monolayer Ba(NO₃)₂ phase after thermal treatment in NO₂, in addition to these large crystals. These results clearly demonstrate the dynamic nature of the Ba-containing phases that are active in the NOx storage/reduction process. The proposed morphology cycle may contribute to the understanding of the changes observed in the performances of these catalysts during actual operating conditions.« less

MdMYB1 Regulates Anthocyanin and Malate Accumulation by Directly Facilitating Their Transport into Vacuoles in Apples1[OPEN

PubMed Central

Hu, Da-Gang; Sun, Cui-Hui; Ma, Qi-Jun; You, Chun-Xiang; Hao, Yu-Jin

2016-01-01

Tonoplast transporters, including proton pumps and secondary transporters, are essential for plant cell function and for quality formation of fleshy fruits and ornamentals. Vacuolar transport of anthocyanins, malate, and other metabolites is directly or indirectly dependent on the H+-pumping activities of vacuolar H+-ATPase (VHA) and/or vacuolar H+-pyrophosphatase, but how these proton pumps are regulated in modulating vacuolar transport is largely unknown. Here, we report a transcription factor, MdMYB1, in apples that binds to the promoters of two genes encoding the B subunits of VHA, MdVHA-B1 and MdVHA-B2, to transcriptionally activate its expression, thereby enhancing VHA activity. A series of transgenic analyses in apples demonstrates that MdMYB1/10 controls cell pH and anthocyanin accumulation partially by regulating MdVHA-B1 and MdVHA-B2. Furthermore, several other direct target genes of MdMYB10 are identified, including MdVHA-E2, MdVHP1, MdMATE-LIKE1, and MdtDT, which are involved in H+-pumping or in the transport of anthocyanins and malates into vacuoles. Finally, we show that the mechanism by which MYB controls malate and anthocyanin accumulation in apples also operates in Arabidopsis (Arabidopsis thaliana). These findings provide novel insights into how MYB transcription factors directly modulate the vacuolar transport system in addition to anthocyanin biosynthesis, consequently controlling organ coloration and cell pH in plants. PMID:26637549

Characteristics and outcomes of Canadian MD/PhD program graduates: a cross-sectional survey

PubMed Central

Skinnider, Michael A.; Squair, Jordan W.; Twa, David D.W.; Ji, Jennifer X.; Kuzyk, Alexandra; Wang, Xin; Steadman, Patrick E.; Zaslavsky, Kirill; Dey, Ayan K.; Eisenberg, Mark J.; Gagné, Ève-Reine; HayGlass, Kent T.; Lewis, James F.; Margetts, Peter J.; Underhill, D. Alan; Rosenblum, Norman D.; Raymond, Lynn A.

2017-01-01

Background: Combined MD/PhD programs provide a structured path for physician-scientist training, but assessment of their success within Canada is limited by a lack of quantitative data. We collected outcomes data for graduates of Canadian MD/PhD programs. Methods: We developed and implemented a Web-based survey consisting of 41 questions designed to collect outcomes data for Canadian MD/PhD program alumni from 8 Canadian universities who had graduated before September 2015. Respondents were categorized into 2 groups according to whether they had or had not completed all training. Results: Of the 186 eligible alumni of MD/PhD programs, 139 (74.7%) completed the survey. A total of 136/138 respondents (98.6%) had completed or were currently completing residency training, and 66/80 (82%) had completed at least 1 postgraduate fellowship. Most (58 [83%]) of the 70 respondents who had completed all training were appointed as faculty at academic institutions, and 37 (53%) had been principal investigators on at least 1 recent funded project. Among the 58 respondents appointed at academic institutions, 44/57 (77%) dedicated at least 20% of their time to research, and 25/57 (44%) dedicated at least 50% to research. During their combined degree, 102/136 respondents (75.0%) published 3 or more first-author papers, and 133/136 (97.8%) matched with their first choice of specialty. The median length of physician-scientist training was 13.5 years. Most respondents graduated with debt despite having been supported by Canadian Institutes of Health Research MD/PhD studentships. Interpretation: Most Canadian MD/PhD program alumni pursued careers consistent with their physician-scientist training, which indicates that these programs are meeting their primary objective. Nevertheless, our findings highlight that a minority of these positions are research intensive; this finding warrants further study. Our data provide a baseline for future monitoring of the output of Canadian MD

Effectiveness of BaTiO 3 dielectric patches on YBa 2Cu 3O 7 thin films for MEM switches

DOE PAGES

Vargas, J.; Hijazi, Y.; Noel, J.; ...

2014-05-12

A micro-electro-mechanical (MEM) switch built on a superconducting microstrip filter will be utilized to investigate BaTiO 3 dielectric patches for functional switching points of contact. Actuation voltage resulting from the MEM switch provokes static friction between the bridge membrane and BaTiO 3 insulation layer. Furthermore, the dielectric patch crystal structure and roughness affect the ability of repetitively switching cycles and lifetime. We performed a series of experiments using different deposition methods and RF magnetron sputtering was found to be the best deposition process for the BaTiO 3 layer. The effect examination of surface morphology will be presented using characterization techniquesmore » as x-ray diffraction, SEM and AFM for an optimum switching device. The thin film is made of YBa 2Cu 3O 7 deposited on LaAlO 3 substrate by pulsed laser deposition. In our work, the dielectric material sputtering pressure is set at 9.5x10 -6 Torr. The argon gas is released through a mass-flow controller to purge the system prior to deposition. RF power is 85 W at a distance of 9 cm. The behavior of Au membranes built on ultimate BaTiO 3 patches will be shown as part of the results. These novel surface patterns will in turn be used in modelling other RF MEM switch devices such as distributed-satellite communication system operating at cryogenic temperatures.« less

Thermoelectric properties of doped BaHfO{sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dixit, Chandra Kr., E-mail: ckparadise@gmail.com, E-mail: sharmarameshfgiet@gmail.com; Bhamu, K. C.; Sharma, Ramesh, E-mail: ckparadise@gmail.com, E-mail: sharmarameshfgiet@gmail.com

2016-05-06

We have studied the structural stability, electronic structure, optical properties and thermoelectric properties of doped BaHfO{sub 3} by full potential linearized augmented plane wave (FP-LAPW) method. The electronic structure of BaHfO{sub 3} doped with Sr shows enhances the indirect band gaps of 3.53 eV, 3.58 eV. The charge density plots show strong ionic bonding in Ba-Hf, and ionic and covalent bonding between Hf and O. Calculations of the optical spectra, viz., the dielectric function, refractive index and extinction coefficient are performed for the energy range are calculated and analyzed. Thermoelectric properties of semi conducting are also reported first time. Themore » doped BaHfO{sub 3} is approximately wide band gap semiconductor with the large p-type Seebeck coefficient. The power factor of BaHfO{sub 3} is increased with Sr doping, decreases because of low electrical resistivity and thermal conductivity.« less

Hybrid MD-Nernst Planck Model of Alpha-hemolysin Conductance Properties

NASA Technical Reports Server (NTRS)

Cozmuta, Ioana; O'Keefer, James T.; Bose, Deepak; Stolc, Viktor

2006-01-01

Motivated by experiments in which an applied electric field translocates polynucleotides through an alpha-hemolysin protein channel causing ionic current transient blockade, a hybrid simulation model is proposed to predict the conductance properties of the open channel. Time scales corresponding to ion permeation processes are reached using the Poisson-Nemst-Planck (PNP) electro-diffusion model in which both solvent and local ion concentrations are represented as a continuum. The diffusion coefficients of the ions (K(+) and Cl(-)) input in the PNP model are, however, calculated from all-atom molecular dynamics (MD). In the MD simulations, a reduced representation of the channel is used. The channel is solvated in a 1 M KCI solution, and an external electric field is applied. The pore specific diffusion coefficients for both ionic species are reduced 5-7 times in comparison to bulk values. Significant statistical variations (17-45%) of the pore-ions diffusivities are observed. Within the statistics, the ionic diffusivities remain invariable for a range of external applied voltages between 30 and 240mV. In the 2D-PNP calculations, the pore stem is approximated by a smooth cylinder of radius approx. 9A with two constriction blocks where the radius is reduced to approx. 6A. The electrostatic potential includes the contribution from the atomistic charges. The MD-PNP model shows that the atomic charges are responsible for the rectifying behaviour and for the slight anion selectivity of the a-hemolysin pore. Independent of the hierarchy between the anion and cation diffusivities, the anionic contribution to the total ionic current will dominate. The predictions of the MD-PNP model are in good agreement with experimental data and give confidence in the present approach of bridging time scales by combining a microscopic and macroscopic model.

Decorating TiO2 Nanowires with BaTiO3 Nanoparticles: A New Approach Leading to Substantially Enhanced Energy Storage Capability of High-k Polymer Nanocomposites.

PubMed

Kang, Da; Wang, Guanyao; Huang, Yanhui; Jiang, Pingkai; Huang, Xingyi

2018-01-31

The urgent demand of high energy density and high power density devices has triggered significant interest in high dielectric constant (high-k) flexible nanocomposites comprising dielectric polymer and high-k inorganic nanofiller. However, the large electrical mismatch between polymer and nanofiller usually leads to earlier electric failure of the nanocomposites, resulting in an undesirable decrease of electrical energy storage capability. A few studies show that the introduction of moderate-k shell onto a high-k nanofiller surface can decrease the dielectric constant mismatch, and thus, the corresponding nanocomposites can withstand high electric field. Unfortunately, the low apparent dielectric enhancement of the nanocomposites and high electrical conductivity mismatch between matrix and nanofiller still result in low energy density and low efficiency. In this study, it is demonstrated that encapsulating moderate-k nanofiller with high-k but low electrical conductivity shell is effective to significantly enhance the energy storage capability of dielectric polymer nanocomposites. Specifically, using BaTiO 3 nanoparticles encapsulated TiO 2 (BaTiO 3 @TiO 2 ) core-shell nanowires as filler, the corresponding poly(vinylidene fluoride-co-hexafluoropylene) nanocomposites exhibit superior energy storage capability in comparison with the nanocomposites filled by either BaTiO 3 or TiO 2 nanowires. The nanocomposite film with 5 wt % BaTiO 3 @TiO 2 nanowires possesses an ultrahigh discharged energy density of 9.95 J cm -3 at 500 MV m -1 , much higher than that of commercial biaxial-oriented polypropylene (BOPP) (3.56 J cm -3 at 600 MV m -1 ). This new strategy and corresponding results presented here provide new insights into the design of dielectric polymer nanocomposites with high electrical energy storage capability.

Effect of salinity and temperature on treatment of concentrated wastewater from RO by FO-MD

NASA Astrophysics Data System (ADS)

Zhou, Yingru; Huang, Manhong; Deng, Qian

2018-02-01

In this study the appropriate temperature of the membrane distillation (MD) hot side (the permeation flux of MD was controlled by adjusting the hot side temperature) was selected according to the water flux of FO process so that the water transfer rate on both sides of FO and MD was consistent and the FO-MD process could be stable operation. When the salt concentration of feed solution was 30, 55, 80 and 100 g/L, the desalination rates changed little, which were 99.1%, 98.4%, 98.9% and 98.7%, respectively. The removal rate of COD was 93.8%, 94.2%, 91.6% and 92.7% which also changed little like the desalination rates. The removal rate of chromaticity increased with the increase of salinity, which attained 96.6%, 97.0%, 97.2% and 97.9%, respectively. This study proved that salinity of the feed solution affected little on the removal rate of contaminants but great on the water flux, with the increase of salinity from 30 to 100 g/L, the water flux was 6.05, 4.81, 4.33 and 3.87 LMH with the appropriate temperature (67.5±0.5, 64.5±0.5, 62.5±0.5 and 60.5±0.5 °C) of MD hot side. In a word, FO-MD was first used to treat the high salinity RO water with over 30 g/L total dissolved solids (TDS), FO-MD was a promising new process for high salinity wastewater treatment, and the hybrid system can solve the problem of lower draw solution concentration, and the high-quality production water will be obtained directly by this hybrid system with low membrane fouling tendency.

Enhanced critical currents in (Gd,Y)Ba2Cu3Ox superconducting tapes with high levels of Zr addition

NASA Astrophysics Data System (ADS)

Selvamanickam, V.; Chen, Y.; Shi, T.; Liu, Y.; Khatri, N. D.; Liu, J.; Yao, Y.; Xiong, X.; Lei, C.; Soloveichik, S.; Galstyan, E.; Majkic, G.

2013-03-01

The critical current and structural properties of (Gd,Y)BaCuO tapes made by metal organic chemical vapor deposition (MOCVD) with Zr addition levels up to 30 at.% have been investigated. The reduction in critical current beyond the previously optimized Zr addition level of 7.5 at.% was found to be due to structural deterioration of the (Gd,Y)Ba2Cu3Ox film. By a modified MOCVD process, enhanced critical current densities have been achieved with high levels of Zr addition, including 3.83 MA cm-2 in 15 at.% Zr-added 1.1 μm thick film at 77 K in zero magnetic field. Critical currents as high as 1072 A/12 mm have been reached in (Gd,Y)BaCuO tapes with 15 at.% Zr addition at 30 K in a field of 3 T applied perpendicular to the tape, corresponding to a pinning force value of 268 GN m-3. The enhanced critical currents achievable with a high density of nanoscale defects by employing high levels of second-phase additions enable the performance targets needed for the use of HTS tapes in coil applications involving high magnetic fields at temperatures below 50 K to be met.

An adaptive bias - hybrid MD/kMC algorithm for protein folding and aggregation.

PubMed

Peter, Emanuel K; Shea, Joan-Emma

2017-07-05

In this paper, we present a novel hybrid Molecular Dynamics/kinetic Monte Carlo (MD/kMC) algorithm and apply it to protein folding and aggregation in explicit solvent. The new algorithm uses a dynamical definition of biases throughout the MD component of the simulation, normalized in relation to the unbiased forces. The algorithm guarantees sampling of the underlying ensemble in dependency of one average linear coupling factor 〈α〉 τ . We test the validity of the kinetics in simulations of dialanine and compare dihedral transition kinetics with long-time MD-simulations. We find that for low 〈α〉 τ values, kinetics are in good quantitative agreement. In folding simulations of TrpCage and TrpZip4 in explicit solvent, we also find good quantitative agreement with experimental results and prior MD/kMC simulations. Finally, we apply our algorithm to study growth of the Alzheimer Amyloid Aβ 16-22 fibril by monomer addition. We observe two possible binding modes, one at the extremity of the fibril (elongation) and one on the surface of the fibril (lateral growth), on timescales ranging from ns to 8 μs.

77 FR 23599 - Special Local Regulations for Marine Events; Potomac River, Charles County, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-20

...-AA08 Special Local Regulations for Marine Events; Potomac River, Charles County, MD AGENCY: Coast Guard...; telephone 410-576-2674, email Ronald.L[email protected] . If you have questions on viewing the docket, call... ``Special Local Regulations for Marine Events; Potomac River, Charles County, MD'' in the Federal Register...

Inter- and intraconfigurational luminescence of Er3+ ions in BaY2F8 under VUV excitation

NASA Astrophysics Data System (ADS)

Kirm, M.; Lichtenberg, H.; Makhov, V. N.; Negodin, E.; Ouvarova, T. V.; Suljoti, E.; True, M.; Zimmerer, G.

Using energy- and time-resolved spectroscopy the luminescence properties of Er3+ doped BaY2F8 crystals were investigated at 10 K under VUV synchrotron radiation excitation. Radiative intraconfigurational f - f and interconfigurational d - f transitions in Er3+ ions were observed under f - d excitation. Whereas the onset of S-4(3/2) population via f - d excitation starts at 59 900 cm(-1) , efficient excitation of emissions arising from the P-2(3/2) state begins only above 67 000 cm(-1) in VUV region. Such behaviour can be explained by a cross-relaxation process of the type (F-2(2)(5/2) , I-4(15/2))-->(P-2(3/2) , P-2(3/2)) taking place within f -states of Er3+ ions finally populating the emitting P-2(3/2) state.

Genome Sequence of African Swine Fever Virus BA71, the Virulent Parental Strain of the Nonpathogenic and Tissue-Culture Adapted BA71V.

PubMed

Rodríguez, Javier M; Moreno, Leticia Tais; Alejo, Alí; Lacasta, Anna; Rodríguez, Fernando; Salas, María L

2015-01-01

The strain BA71V has played a key role in African swine fever virus (ASFV) research. It was the first genome sequenced, and remains the only genome completely determined. A large part of the studies on the function of ASFV genes, viral transcription, replication, DNA repair and morphogenesis, has been performed using this model. This avirulent strain was obtained by adaptation to grow in Vero cells of the highly virulent BA71 strain. We report here the analysis of the genome sequence of BA71 in comparison with that of BA71V. They possess the smallest genomes for a virulent or an attenuated ASFV, and are essentially identical except for a relatively small number of changes. We discuss the possible contribution of these changes to virulence. Analysis of the BA71 sequence allowed us to identify new similarities among ASFV proteins, and with database proteins including two ASFV proteins that could function as a two-component signaling network.

Genome Sequence of African Swine Fever Virus BA71, the Virulent Parental Strain of the Nonpathogenic and Tissue-Culture Adapted BA71V

PubMed Central

Rodríguez, Javier M.; Moreno, Leticia Tais; Alejo, Alí; Lacasta, Anna; Rodríguez, Fernando; Salas, María L.

2015-01-01

The strain BA71V has played a key role in African swine fever virus (ASFV) research. It was the first genome sequenced, and remains the only genome completely determined. A large part of the studies on the function of ASFV genes, viral transcription, replication, DNA repair and morphogenesis, has been performed using this model. This avirulent strain was obtained by adaptation to grow in Vero cells of the highly virulent BA71 strain. We report here the analysis of the genome sequence of BA71 in comparison with that of BA71V. They possess the smallest genomes for a virulent or an attenuated ASFV, and are essentially identical except for a relatively small number of changes. We discuss the possible contribution of these changes to virulence. Analysis of the BA71 sequence allowed us to identify new similarities among ASFV proteins, and with database proteins including two ASFV proteins that could function as a two-component signaling network. PMID:26618713

Method of forming superconducting Tl-Ba-Ca-Cu-O films

DOEpatents

Wessels, Bruce W.; Marks, Tobin J.; Richeson, Darrin S.; Tonge, Lauren M.; Zhang, Jiming

1993-01-01

A method of forming a superconducting Tl-Ba-Ca-Cu-O film is disclosed, which comprises depositing a Ba-Ca-Cu-O film on a substrate by MOCVD, annealing the deposited film and heat-treating the annealed film in a closed circular vessel with TlBa.sub.2 Ca.sub.2 Cu.sub.3 O.sub.x and cooling to form said superconducting film of TlO.sub.m Ba.sub.2 Ca.sub.n-1 Cu.sub.n O.sub.2n+2, wherein m=1,2 and n=1,2,3.

Opinion of stakeholders on existing curriculum for postgraduate (MD) course in Pharmacology: A survey.

PubMed

Badyal, Dinesh K; Daniel, Sujit R

2016-10-01

To survey the opinion about various curricular components of Doctor of Medicine (MD) pharmacology curriculum in India by stakeholders, including faculty and students. An online survey was done to evaluate the various curricular components of MD pharmacology curriculum being used in India. A total of 393 respondents including faculty, MD students, and other stakeholders completed the survey. The survey was developed using SurveyMonkey platform and link to survey was E-mailed to stakeholders. The results were expressed as percentages. There was a balanced representation of respondents from various designations, teaching experience, regions, and age groups. Most of the respondents (83%) were aware of the MD pharmacology curriculum. However, they reported that it is more inclined to knowledge domain. About half of respondents (53%) said that animal experiments are being used. The most common teaching methods mentioned are seminars (98.5%), journal clubs (95%), and practical exercises by postgraduates (73%), but there is less use of newer methods (25%) in theory and less of clinical pharmacology exercise (39%) in practical classes. The log books are maintained but not assessed regularly. Internal assessment is sparingly used. The MD pharmacology curriculum needs to be made uniform at the national level and updated to include the newer methods in teaching-learning and assessment. There should be sharing of newer methods at a common platform implemented at the national level.

MD-2 residues tyrosine 42, arginine 69, aspartic acid 122, and leucine 125 provide species specificity for lipid IVA.

PubMed

Meng, Jianmin; Drolet, Joshua R; Monks, Brian G; Golenbock, Douglas T

2010-09-03

Lipopolysaccharide (LPS) activates the innate immune response through the Toll-like receptor 4 (TLR4).MD-2 complex. A synthetic lipid A precursor, lipid IV(A), induces an innate immune response in mice but not in humans. Both TLR4 and MD-2 are required for the agonist activity of lipid IV(A) in mice, with TLR4 interacting through specific surface charges at the dimerization interface. In this study, we used site-directed mutagenesis to identify the MD-2 residues that determine lipid IV(A) species specificity. A single mutation of murine MD-2 at the hydrophobic pocket entrance, E122K, substantially reduced the response to lipid IV(A). Combining the murine MD-2 E122K with the murine TLR4 K367E/S386K/R434Q mutations completely abolished the response to lipid IV(A), effectively converting the murine cellular response to a human-like response. In human cells, however, simultaneous mutations of K122E, K125L, Y41F, and R69G on human MD-2 were required to promote a response to lipid IV(A). Combining the human MD-2 quadruple mutations with the human TLR4 E369K/Q436R mutations completely converted the human MD-2/human TLR4 receptor to a murine-like receptor. Because MD-2 residues 122 and 125 reside at the dimerization interface near the pocket entrance, surface charge differences here directly affect receptor dimerization. In comparison, residues 42 and 69 reside at the MD-2/TLR4 interaction surface opposite the dimerization interface. Surface charge differences there likely affect the binding angle and/or rigidity between MD-2 and TLR4, exerting an indirect influence on receptor dimerization and activation. Thus, surface charge differences at the two MD-2/TLR4 interfaces determine the species-specific activation of lipid IV(A).

The Jasmonate-Activated Transcription Factor MdMYC2 Regulates ETHYLENE RESPONSE FACTOR and Ethylene Biosynthetic Genes to Promote Ethylene Biosynthesis during Apple Fruit Ripening.

PubMed

Li, Tong; Xu, Yaxiu; Zhang, Lichao; Ji, Yinglin; Tan, Dongmei; Yuan, Hui; Wang, Aide

2017-06-01

The plant hormone ethylene is critical for ripening in climacteric fruits, including apple ( Malus domestica ). Jasmonate (JA) promotes ethylene biosynthesis in apple fruit, but the underlying molecular mechanism is unclear. Here, we found that JA-induced ethylene production in apple fruit is dependent on the expression of MdACS1 , an ACC synthase gene involved in ethylene biosynthesis. The expression of MdMYC2 , encoding a transcription factor involved in the JA signaling pathway, was enhanced by MeJA treatment in apple fruits, and MdMYC2 directly bound to the promoters of both MdACS1 and the ACC oxidase gene MdACO1 and enhanced their transcription. Furthermore, MdMYC2 bound to the promoter of MdERF3 , encoding a transcription factor involved in the ethylene-signaling pathway, thereby activating MdACS1 transcription. We also found that MdMYC2 interacted with MdERF2, a suppressor of MdERF3 and MdACS1 This protein interaction prevented MdERF2 from interacting with MdERF3 and from binding to the MdACS1 promoter, leading to increased transcription of MdACS1 Collectively, these results indicate that JA promotes ethylene biosynthesis through the regulation of MdERFs and ethylene biosynthetic genes by MdMYC2. © 2017 American Society of Plant Biologists. All rights reserved.

Compositional Homogeneity of CM Parent Bodies

NASA Astrophysics Data System (ADS)

Vernazza, P.; Marsset, M.; Beck, P.; Binzel, R. P.; Birlan, M.; Cloutis, E. A.; DeMeo, F. E.; Dumas, C.; Hiroi, T.

2016-09-01

CM chondrites are the most common type of hydrated meteorites, making up ˜1.5% of all falls. Whereas most CM chondrites experienced only low-temperature (˜0°C-120°C) aqueous alteration, the existence of a small fraction of CM chondrites that suffered both hydration and heating complicates our understanding of the early thermal evolution of the CM parent body(ies). Here, we provide new constraints on the collisional and thermal history of CM-like bodies from a comparison between newly acquired spectral measurements of main-belt Ch/Cgh-type asteroids (70 objects) and existing laboratory spectral measurements of CM chondrites. It first appears that the spectral variation observed among CM-like bodies is essentially due to variations in the average regolith grain size. Second, the spectral properties of the vast majority (unheated) of CM chondrites resemble both the surfaces and the interiors of CM-like bodies, implying a “low” temperature (<300°C) thermal evolution of the CM parent body(ies). It follows that an impact origin is the likely explanation for the existence of heated CM chondrites. Finally, similarly to S-type asteroids and (2) Pallas, the surfaces of large (D > 100 km)—supposedly primordial—Ch/Cgh-type main-belt asteroids likely expose the interiors of the primordial CM parent bodies, a possible consequence of impacts by small asteroids (D < 10 km) in the early solar system.

Gordon Fullerton in PCA (MD-11) Simulator

NASA Technical Reports Server (NTRS)

1998-01-01

NASA research pilot Gordon Fullerton 'flying' in the MD-11 simulator during the Propulsion Controlled Aircraft (PCA) project. This investigation grew out of the crash of a DC-10 airliner on July 19, 1989, following an explosion in the rear engine which caused the loss of all manual flight controls. The flight crew attempted to control the airliner using only the thrust from the two remaining engines. Although the DC-10 crashed during the landing attempt, 184 of the 296 passengers and crew aboard survived. The PCA effort at the Dryden Flight Research Center grew out of the crash, and attempted to develop a means to successfully land an aircraft using only engine thrust. After more than five years of work, on August 29, 1995, Gordon Fullerton made the first PCA touchdown aboard an MD-11 airliner (a later version of the DC-10). The concept was further refined over the years that followed this first landing. Simulators were essential ingredients of the PCA development process. The feasibility of the concept was first tested with an F-15 simulator, then the results of actual flight tests in an F-15 were incorporated back into the simulator. Additional simulations were run on the Boeing 720 airliner simulator used in the Controlled Impact Demonstration project. After the MD-11 test landings, Boeing 747 and 757 simulators tested a wide range of possible situations. Simulations even helped develop a method of landing an airliner if it lost its complete hydraulic system as well as a wing engine, by transferring fuel to shift the center of gravity toward the working engine. The most extreme procedure was undertaken in a 747 simulator. The aircraft simulated the loss of the hydraulic system at 35,000 feet and rolled upside down. Then, the PCA mode was engaged, the airliner righted itself, leveled its wings, and made an approach nearly identical to that of a normal auto landing.

The new barium zinc mercurides Ba3ZnHg10 and BaZn0.6Hg3.4 - Synthesis, crystal and electronic structure

NASA Astrophysics Data System (ADS)

Schwarz, Michael; Wendorff, Marco; Röhr, Caroline

2012-12-01

The title compounds Ba3ZnHg10 and BaZn0.6Hg3.4 were synthesized from stoichiometric ratios of the elements in Ta crucibles. Their crystal structures, which both represent new structure types, have been determined using single crystal X-ray data. The structure of Ba3ZnHg10 (orthorhombic, oP28, space group Pmmn, a=701.2(3), b=1706.9(8), c=627.3(3)pm, Z=2, R1=0.0657) contains folded 44 Hg nets, where the meshes form the bases of flat rectangular pyramids resembling the structure of BaAl4. The flat pyramids are connected via Hg-Zn/Hg bonds, leaving large channels at the folds, in which Ba(1) and Hg(2) atoms alternate. Whereas the remaining Hg/Zn atoms form a covalent 3D network of three- to five-bonded atoms with short M-M distances (273-301 pm; CN 9-11), the Hg(2) atoms in the channels adopt a comparatively large coordination number of 12 and increased distances (317-348 pm) to their Zn/Hg neighbours. In the structure of BaZn0.6Hg3.4 (cubic, cI320, space group I4bar3d, a=2025.50(7) pm, Z=64, R1=0.0440), with a chemical composition not much different from that of Ba3ZnHg10, the Zn/Hg atoms of the mixed positions M(1/2) are arranged in an slightly distorted primitive cubic lattice with a 4×4×4 subcell relation to the unit cell. The 24 of the originating 64 cubes contain planar cis tetramers Hg(5,6)4 with Hg in a nearly trigonal planar or tetrahedral coordination. In another 24 of the small cubes, two opposing faces are decorated by Hg(3,4)2 dumbbells, two by Ba(2) atoms respectively. The third type of small cubes are centered by Ba(1) atoms only. The complex 3D polyanionic Hg/Zn network thus formed is compared with the Hg partial structure in Rb3Hg20 applying a group-subgroup relation. Despite their different overall structures, the connectivity of the negatively charged Hg atoms, the rather metallic Zn bonding characteristic (as obtained from FP-LAPW band structure calculations) and the coordination number of 16 for all Ba cations relate the two title compounds.

Ba 2TeO: A new layered oxytelluride

DOE PAGES

Besara, T.; Ramirez, D.; Sun, J.; ...

2015-02-01

For single crystals of the new semiconducting oxytelluride phase, Ba 2TeO, we synthesized from barium oxide powder and elemental tellurium in a molten barium metal flux. Ba 2TeO crystallizes in tetragonal symmetry with space group P4/nmm (#129), a=5.0337(1) Å, c=9.9437(4) Å, Z=2. The crystals were characterized by single crystal x-ray diffraction, heat capacity and optical measurements. Moreover, the optical measurements along with electronic band structure calculations indicate semiconductor behavior with a band gap of 2.93 eV. Resistivity measurements show that Ba 2TeO is highly insulating.

Analysis of oxygen binding-energy variations for BaO on W

NASA Astrophysics Data System (ADS)

Haas, G. A.; Shih, A.; Mueller, D.; Thomas, R. E.

Interatomic Auger analyses have been made of different forms of BaO layers on W substrates. Variations in Auger spectroscopy energies of the Ba4dBa5pO2p interatomic Auger transition were found to be largely governed by the O2p binding energy of the BaO adsorbate. This was illustrated by comparing results of the Auger data values with values derived from O2p binding energies using ultraviolet photoelectron spectroscopy. Very good agreement was observed not only for the W<100> substrate but also for the W<110> substrate which showed two oxygen-induced electronics state. Variations in binding energy were noted for different states of BaO lattice formation and for different amounts of oxidation, ranging from the transition of Ba to BaO and continuing to the BaO 2 stoichiometry and beyond. Effects were also reported for adsorbate alignment and thermal activation (i.e., reduction) of the oxidized state. An empirical relationship was found suggesting that the more tightly bound the O2p states of the BaO adsorbate were, the lower its work function would be. This link between binding energy and work function was observed to be valid not only for cases of poisoning by oxidation, but held as well during reactivation by the subsequent reduction of the oxide. In addition, this relationship also appeared to predict the low work function obtained through the introduction of substances such as Sc to the BaO-W system. Possible qualitative reasons which might contribute to this are discussed in terms of enhanced dipole effects and shifts in band structure.

Improved ferroelectric, piezoelectric and electrostrictive properties of dense BaTiO{sub 3} ceramic

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baraskar, Bharat G.; Kakade, S. G.; Kambale, R. C., E-mail: rckambale@gmail.com

2016-05-23

The ferroelectric, piezoelectric and electrostrictive properties of BaTiO{sub 3} (BT) dense ceramic synthesized by solid-state reaction were investigated. X-ray diffraction study confirmed tetragonal crystal structure having c/a ~1.0144. The dense microstructure was evidenced from morphological studies with an average grain size ~7.8 µm. Temperature dependent dielectric measurement showed the maximum values of dielectric constant, ε{sub r} = 5617 at Curie temperature, T{sub c} = 125 °C. The saturation and remnant polarization, P{sub sat.} = 24.13 µC/cm{sup 2} and P{sub r} =10.42 µC/cm{sup 2} achieved respectively for the first time with lower coercive field of E{sub c}=2.047 kV/cm. The polarization currentmore » density-electric field measurement exhibits the peaking characteristics, confirms the saturation state of polarization for BT. The strain-electric field measurements revealed the “sprout” shape nature instead of typical “butterfly loop”. This shows the excellent converse piezoelectric response with remnant strain ~ 0.212% and converse piezoelectric constant d*{sub 33} ~376.35 pm/V. The intrinsic electrostrictive coefficient was deduced from the variation of strain with polarization with electrostrictive coefficient Q{sub 33}~ 0.03493m{sup 4}/C{sup 2}.« less

Evaluation of Argonne 9-cm and 10-cm Annular Centrifugal Contactors for SHINE Solution Processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wardle, Kent E.; Pereira, Candido; Vandegrift, George

2015-02-01

Work is in progress to evaluate the SHINE Medical Technologies process for producing Mo-99 for medical use from the fission of dissolved low-enriched uranium (LEU). This report addresses the use of Argonne annular centrifugal contactors for periodic treatment of the process solution. In a letter report from FY 2013, Pereira and Vandegrift compared the throughput and physical footprint for the two contactor options available from CINC Industries: the V-02 and V-05, which have rotor diameters of 5 cm and 12.7 cm, respectively. They suggested that an intermediately sized “Goldilocks” contactor might provide a better balance between throughput and footprint tomore » meet the processing needs for the uranium extraction (UREX) processing of the SHINE solution to remove undesired fission products. Included with the submission of this letter report are the assembly drawings for two Argonne-design contactors that are in this intermediate range—9-cm and 10-cm rotors, respectively. The 9-cm contactor (drawing number CE-D6973A, stamped February 15, 1978) was designed as a single-stage unit and built and tested in the late 1970s along with other size units, both smaller and larger. In subsequent years, a significant effort to developed annular centrifugal contactors was undertaken to support work at Hanford implementing the transuranic extraction (TRUEX) process. These contactors had a 10-cm rotor diameter and were fully designed as multistage units with four stages per assembly (drawing number CMT-E1104, stamped March 14, 1990). From a technology readiness perspective, these 10-cm units are much farther ahead in the design progression and, therefore, would require significantly less re-working to make them ready for UREX deployment. Additionally, the overall maximum throughput of ~12 L/min is similar to that of the 9-cm unit (10 L/min), and the former could be efficiently operated over much of the same range of throughput. As a result, only the 10-cm units are

A Highly Parallelized Special-Purpose Computer for Many-Body Simulations with an Arbitrary Central Force: MD-GRAPE

NASA Astrophysics Data System (ADS)

Fukushige, Toshiyuki; Taiji, Makoto; Makino, Junichiro; Ebisuzaki, Toshikazu; Sugimoto, Daiichiro

1996-09-01

We have developed a parallel, pipelined special-purpose computer for N-body simulations, MD-GRAPE (for "GRAvity PipE"). In gravitational N- body simulations, almost all computing time is spent on the calculation of interactions between particles. GRAPE is specialized hardware to calculate these interactions. It is used with a general-purpose front-end computer that performs all calculations other than the force calculation. MD-GRAPE is the first parallel GRAPE that can calculate an arbitrary central force. A force different from a pure 1/r potential is necessary for N-body simulations with periodic boundary conditions using the Ewald or particle-particle/particle-mesh (P^3^M) method. MD-GRAPE accelerates the calculation of particle-particle force for these algorithms. An MD- GRAPE board has four MD chips and its peak performance is 4.2 GFLOPS. On an MD-GRAPE board, a cosmological N-body simulation takes 6O0(N/10^6^)^3/2^ s per step for the Ewald method, where N is the number of particles, and would take 24O(N/10^6^) s per step for the P^3^M method, in a uniform distribution of particles.

Rietveld refined structural and room temperature vibrational properties of BaTiO3 doped La0.67Ba0.33MnO3 composites

NASA Astrophysics Data System (ADS)

Dar, M. A.; Sheikh, M. W.; Malla, M. S.; Varshney, Dinesh

2016-05-01

The composites of (1-x) La0.67Ba0.33MnO3 (LBMO) + xBaTiO3 (BTO) (x = 0, 0.25 and 1.0) were synthesized by conventional solid-state reaction method. Rietveld refinement was employed to characterize the structural information of the prepared ceramics. The result of the Rietveld refinement of X-ray powder diffraction of La0.67Ba0.33MnO3 and BaTiO3 shows that these compounds crystallize in rhombohedral (R3c) and tetragonal (P4mm), respectively. The structural parameters and the reliability factors for the LBMO-BTO composite ceramics were successfully determined by the Rietveld refinement. At room temperature, Raman active phonon modes predicted by the group theory were observed only in BaTiO3 and composite sample. Pure LBMO does not show any Raman active Phonon mode at room temperature.

75 FR 81125 - Drawbridge Operation Regulation; Sassafras River, Georgetown, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-27

..., in Georgetown, MD. The deviation is necessary to facilitate mechanical repairs and gate replacement... facilitate mechanical repairs and barrier gate replacement. The Sassafras River Bridge (Route 213), at mile...

Effects of electron irradiation and temperature on 1 ohm-cm and 10 ohm-cm silicon solar cells

NASA Technical Reports Server (NTRS)

Nicoletta, C. A.

1973-01-01

One OHM-cm and 10 OHM-cm silicon solar cells were exposed to 1.0 MeV electrons at a fixed flux of 10 to the 11th power e/sq cm/sec and fluences of 10 to the 13th power, 10 to the 14th power and 10 to the 15th power e/sq.cm. 1-V curves of the cells were made at room temperature, - 63 C and + or - 143 C after each irradiation. A value of 139.5 mw/sq cm was used as AMO incident energy rate per unit area. The 10 OHM-cm cells appear more efficient than 1 OHM-cm cells after exposure to a fluence greater than 10 to the 14th power e/sq cm. The 1.0 MeV electron damage coefficients for both 1 OHM-cm and 10 OHM-cm cells are somewhat less than those for previously irradiated cells at room temperature. The values of the damage coefficients increase as the cell temperatures decrease. Efficiencies pertaining to maximum power output are about the same as those of n on p silicon cells evaluated previously.

Functional identification of MdSIZ1 as a SUMO E3 ligase in apple.

PubMed

Zhang, Rui-Fen; Guo, Ying; Li, Yuan-Yuan; Zhou, Li-Jie; Hao, Yu-Jin; You, Chun-Xiang

2016-07-01

SUMOylation, the conjugation of target proteins with SUMO (small ubiquitin-related modifier), is a type of post-translational modification in eukaryotes and involves the sequential action of activation (E1), conjugation (E2) and ligation (E3) enzymes. In Arabidopsis, the AtSIZ1 protein is a SUMO E3 ligase that promotes the conjugation of SUMO proteins to target substrates. Here, we isolated and identified a SUMO E3 ligase, MdSIZ1, in apple, which was similar to AtSIZ1. SUMOylation analysis showed that MdSIZ1 had SUMO E3 ligase activity in vitro and in vivo. SUMO conjugation was increased by high temperatures, low temperatures, and abscisic acid (ABA). The ectopic expression of MdSIZ1 in Arabidopsis siz1-2 mutant plants partially complemented the morphological mutant phenotype and enhanced the levels of SUMO conjugation. Taken together, these results suggest that MdSIZ1-mediated SUMO conjugation of target proteins is an important process that regulates the adaptation of apple plants to various environmental stresses. Copyright © 2016 Elsevier GmbH. All rights reserved.

Stephen Baylin, M.D., Explains Genetics and Epigenetics - TCGA

Cancer.gov

Stephen Baylin, M.D., at the Johns Hopkins Kimmel Cancer Center discusses the how alterations in the DNA code are deciphered in a combined effort with The Cancer Genome Atlas at the National Cancer Institute to decode the brain cancer genome.

Characteristics of B2O3 and Fe added into BaFe12O19 permanent magnets prepared at different milling time and sintering temperature

NASA Astrophysics Data System (ADS)

Sebayang, Perdamean; Sari, Ayu Yuswita; Ginting, Delovita; Allan, Yola; Nasruddin M., N.; Sebayang, Kerista

2016-02-01

The objective of present work is to investigate the characteristic of BaFe12O19, B2O3-BaFe12O19 and Fe-BaFe12O19 magnets fabricated at different milling time and sintering temperature. The characteristic of perrmanen magnet BaFe12O19 with different content of B2O3 and Fe which was fabricated at different milling time and sintering temperature were investigated. The powder mixtures were prepared by dry and wet milling at various milling time. The powder were mixtured and prepared by dry and wet milling at various milling time. The mixture powder was then compacted by anisotropic with compressive pressure of 50 N/cm2. The green bodies were sinter at 1050, 1100, 1150 and 1200°C and hold for 1 h, separately. The density, magnetic flux density and B-H curve were measured by Archimedes principle, Gauss meter and Permagraph, respectively. The microstructure and phase composition characterization were performed by SEM and XRD. The results of this study are presented in this paper. It shows that addition of Fe (in wet milling) and B2O3 (in dry milling) respectively give a potential benefit to reduce the sintering temperature and improve the magnetic flux density of barium hexaferrite.

Modeling Nanocomposites for Molecular Dynamics (MD) Simulations

DTIC Science & Technology

2015-01-01

Parallel Simulator ( LAMMPS ) is used as the MD simulator [9], the coordinates must be formatted for use in LAMMPSs. VMD has a set of tools (TopoTools...that can be used to generate a LAMMPS -readable format [6]. 3 Figure 4. Ethylene Monomer Produced From Coordinates in PDB and Rendered Using...where, i and j are the atom subscripts. Simulations are performed using LAMMPS simulation software. Periodic boundary conditions are

78 FR 17996 - MCM Rail Services LLC-Petition for Retroactive Exemption-In Sparrows Point, Md.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-25

... LLC--Petition for Retroactive Exemption--In Sparrows Point, Md. AGENCY: Surface Transportation Board... of rail line in Sparrows Point, Md. (the Line). DATES: MCM's supplemental information is due by April... Railroad, and currently named the Baltimore Industrial Railway, is located at 1430 Sparrows Point Boulevard...

Optical spectroscopy of Ce3+ ions in BaY2F8 single crystals

NASA Astrophysics Data System (ADS)

Francini, R.; Pinelli, S.; Baraldi, A.; Capelletti, R.; Sani, E.; Toncelli, A.; Tonelli, M.

In the present work we report on the spectroscopic properties of the Ce3+ ion in BaY2F8 single crystals. The absorption and excitation spectra of the emission centered at 340 nm have been measured in the temperature range 15-300 K. The 340 nm emission consists of two broad partially overlapping bands, peaking at 324 and 347 nm (at 15 K), respectively. The full width at half maximum is about 0.5 eV at room temperature. The absorption spectrum of the lowest in energy component of the f --> d transition of Ce3+ reveals at low temperature a marked vibronic structure. High resolution (0.02 cm(-1)) Fourier transform infrared spectroscopy in the wave number range 500-5000 cm(-1) and in the temperature range 9-300 K has been exploited to monitor the f level splitting. The absorption transitions from the three Stark components of the F-2(5/2) manifold to the four of the F-2(7/2) one, have been monitored in the wave number range 2000-3400 cm(-1) . The wave number separation at 9 K between the lowest level of the ground F-2(5/2) manifold and lowest one of the F-2 (7/2) manifold is found to be 2197.47 cm(-1) in good agreement with the splitting detected between the two components of the d --> f emission.

76 FR 31235 - Safety Zone; Ocean City Air Show, Atlantic Ocean, Ocean City, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-31

...-AA00 Safety Zone; Ocean City Air Show, Atlantic Ocean, Ocean City, MD AGENCY: Coast Guard, DHS. ACTION... in the vicinity of Ocean City, MD to support the Ocean City Air Show. This action is necessary to provide for the safety of life on navigable waters during the Ocean City Air Show. This action is intended...

The Jasmonate-Activated Transcription Factor MdMYC2 Regulates ETHYLENE RESPONSE FACTOR and Ethylene Biosynthetic Genes to Promote Ethylene Biosynthesis during Apple Fruit Ripening[OPEN

PubMed Central

Xu, Yaxiu; Zhang, Lichao; Ji, Yinglin; Tan, Dongmei; Yuan, Hui

2017-01-01

The plant hormone ethylene is critical for ripening in climacteric fruits, including apple (Malus domestica). Jasmonate (JA) promotes ethylene biosynthesis in apple fruit, but the underlying molecular mechanism is unclear. Here, we found that JA-induced ethylene production in apple fruit is dependent on the expression of MdACS1, an ACC synthase gene involved in ethylene biosynthesis. The expression of MdMYC2, encoding a transcription factor involved in the JA signaling pathway, was enhanced by MeJA treatment in apple fruits, and MdMYC2 directly bound to the promoters of both MdACS1 and the ACC oxidase gene MdACO1 and enhanced their transcription. Furthermore, MdMYC2 bound to the promoter of MdERF3, encoding a transcription factor involved in the ethylene-signaling pathway, thereby activating MdACS1 transcription. We also found that MdMYC2 interacted with MdERF2, a suppressor of MdERF3 and MdACS1. This protein interaction prevented MdERF2 from interacting with MdERF3 and from binding to the MdACS1 promoter, leading to increased transcription of MdACS1. Collectively, these results indicate that JA promotes ethylene biosynthesis through the regulation of MdERFs and ethylene biosynthetic genes by MdMYC2. PMID:28550149

Phase separation enhanced magneto-electric coupling in La0.7Ca0.3MnO3/BaTiO3 ultra-thin films

PubMed Central

Alberca, A.; Munuera, C.; Azpeitia, J.; Kirby, B.; Nemes, N. M.; Perez-Muñoz, A. M.; Tornos, J.; Mompean, F. J.; Leon, C.; Santamaria, J.; Garcia-Hernandez, M.

2015-01-01

We study the origin of the magnetoelectric coupling in manganite films on ferroelectric substrates. We find large magnetoelectric coupling in La0.7Ca0.3MnO3/BaTiO3 ultra-thin films in experiments based on the converse magnetoelectric effect. The magnetization changes by around 30–40% upon applying electric fields on the order of 1 kV/cm to the BaTiO3 substrate, corresponding to magnetoelectric coupling constants on the order of α = (2–5)·10−7 s/m. Magnetic anisotropy is also affected by the electric field induced strain, resulting in a considerable reduction of coercive fields. We compare the magnetoelectric effect in pre-poled and unpoled BaTiO3 substrates. Polarized neutron reflectometry reveals a two-layer behavior with a depressed magnetic layer of around 30 Å at the interface. Magnetic force microscopy (MFM) shows a granular magnetic structure of the La0.7Ca0.3MnO3. The magnetic granularity of the La0.7Ca0.3MnO3 film and the robust magnetoelastic coupling at the La0.7Ca0.3MnO3/BaTiO3 interface are at the origin of the large magnetoelectric coupling, which is enhanced by phase separation in the manganite. PMID:26648002

The Crystal Structure of Ba 17Sm 10Cl 64

NASA Astrophysics Data System (ADS)

Liu, Guo; Eick, Harry A.

1999-08-01

The structure of Ba17Sm10Cl64, prepared by solvolytic extraction of a program-cooled 1:1 BaCl2:SmCl3 molar mixture sealed in a quartz tube and heated to 750°C, was determined from single-crystal X-ray diffraction data. The compound exhibits cubic symmetry, space group Pa3 (No. 205) with a=21.366(2) Å and Z=4. Refinement effected with I>2σ(I) yielded R1= 0.0926 and wR2=0.216. One Ba atom is 12-coordinated by Cl atoms in a distorted icosahedral arrangement; the three other Ba atoms are 10-coordinated in a distorted bicapped cubic arrangement. There are two Sm atom sites. The coordination around one Sm atom is best described as square antiprismatic, but one Sm-Cl distance is too long for effective bonding. The other Sm atom site, occupied statistically by {1}/{3}Ba and {2}/{3}Sm atoms, is 9-coordinated by Cl atoms in a monocapped square antiprismatic arrangement. The two types of Sm sites combine to form an M6Cl37 cuboctahedral cluster of the composition BaSm5Cl37. It is shown that the cβ phase identified previously in the Yb-F and related fluoride systems is probably isostructural with Ba17Sm10Cl64.

77 FR 18963 - Airworthiness Directives; MD Helicopters, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-29

...) Model MD900 helicopters. The existing AD requires a visual inspection, and if necessary, an eddy current... with an airworthy lower hub. If there is no crack as a result of the visual inspection, eddy current... nondestructive eddy current inspection of the lower hub. That AD was prompted by cracks found on four lower hubs...

Crystal MD: The massively parallel molecular dynamics software for metal with BCC structure

NASA Astrophysics Data System (ADS)

Hu, Changjun; Bai, He; He, Xinfu; Zhang, Boyao; Nie, Ningming; Wang, Xianmeng; Ren, Yingwen

2017-02-01

Material irradiation effect is one of the most important keys to use nuclear power. However, the lack of high-throughput irradiation facility and knowledge of evolution process, lead to little understanding of the addressed issues. With the help of high-performance computing, we could make a further understanding of micro-level-material. In this paper, a new data structure is proposed for the massively parallel simulation of the evolution of metal materials under irradiation environment. Based on the proposed data structure, we developed the new molecular dynamics software named Crystal MD. The simulation with Crystal MD achieved over 90% parallel efficiency in test cases, and it takes more than 25% less memory on multi-core clusters than LAMMPS and IMD, which are two popular molecular dynamics simulation software. Using Crystal MD, a two trillion particles simulation has been performed on Tianhe-2 cluster.

Er3+-doped BaY2F8 crystal waveguides for broadband optical amplification at 1.5 μm

NASA Astrophysics Data System (ADS)

Toccafondo, V.; Cerqueira S., A.; Faralli, S.; Sani, E.; Toncelli, A.; Tonelli, M.; Di Pasquale, F.

2007-01-01

Integrated waveguide amplifiers based on high concentration Er3+ doped BaY2F8 crystals are numerically studied by combining a full-vectorial finite element based modal analysis and propagation-rate equations. Using realistic input data, such as the absorption/emission cross sections and Er level lifetimes measured on grown crystal samples, we investigate the amplifier performance by optimizing the total Er concentration. We predict optimum gain coefficient up to 5dB/cm and broad amplification bandwidth exceeding 80nm with 1480nm pumping.

Bound-bound transitions in the emission spectra of Ba+-He excimer

NASA Astrophysics Data System (ADS)

Moroshkin, P.; Kono, K.

2016-05-01

We present an experimental and theoretical study of the emission and absorption spectra of the Ba+ ions and Ba+*He excimer quasimolecules in the cryogenic Ba-He plasma. We observe several spectral features in the emission spectrum, which we assign to the electronic transitions between bound states of the excimer correlating to the 6 2P3 /2 and 5 2D3 /2 ,5 /2 states of Ba+. The resulting Ba+(5 2DJ) He is a metastable electronically excited complex with orbital angular momentum L =2 , thus expanding the family of known metal-helium quasimolecules. It might be suitable for high-resolution spectroscopic studies and for the search for new polyatomic exciplex structures.

Nuclear spectroscopy of doubly-even130,132Ba

NASA Astrophysics Data System (ADS)

Gupta, Anuradha; Gupta, Surbhi; Singh, Suram; Bharti, Arun

2018-05-01

A comparative study of some high-spin characteristic nuclear structure properties of doubly-even 130,132Ba nuclei has been made using two microscopic frameworks - CHFB and PSM. The yrast spectra, intrinsic quadrupole moment and deformation systematics of these nuclei have been successfully calculated. Further, the calculated data from both the frameworks is also compared with the available experimental data and a good agreement has been obtained. The present CHFB calculations describes very well the low spin structure of even-even 130,132Ba nuclei whereas PSM calculations provide a qualitative description of the high-spin band structure of doubly-even 130,132Ba nuclei.

Review of 40-year MD theses in medical oncology.

PubMed

Zeeneldin, Ahmed; Diyaa, Amira; Moneer, Manar; Elgammal, Mosaad; Buhoush, Wafa

2014-09-01

It is almost 40 years since the foundation of the Medical Oncology (MO) Department. We aimed to appraise the clinical research to fulfill the Medical Doctorate (MD) degree in MO at the National Cancer Institute, Cairo University (NCI, CU). This review included 62 MD theses containing 66 studies. They were reviewed regarding aims, type of study, clinical trial phase, design and methodology, statistical tests, results, limitations, consent and IRB approval. Theses were grouped into 3 periods: 1970-1989, 1990-1999 and 2000-2008. Almost 76% of the studies were interventional and 24% were observational. Informed consent and Institutional Review Board approval were mentioned in 18 and 2 studies, respectively. While all studies mentioned the aims, none, clearly mentioned the research question. Outcomes were mainly efficacy followed by safety. Study design was inadequately considered, especially in 70's-80's period (p=0.038). Median sample size and study duration were almost stable through the three periods (p=0.441, 0.354, respectively). Most of the studies used both descriptive and analytical statistical methods. In a descending order, researched cancers were lymphoma, breast, leukemia, liver, urinary bladder, lung and colorectal. The commonest stages researched were IV and III. The number of studies focused on assessing biomarkers, biomarkers plus drugs/procedures, drugs and procedures are 20, 20, 16 and 6, respectively. With time, research within MD theses in MO increased quantitatively and qualitatively. Improvements were noticeable in documentation of study design. Copyright © 2014. Production and hosting by Elsevier B.V.

Raman spectra of Nd/Sn cosubstituted Ba6-3xSm8+2xTi18O54 microwave dielectric ceramics

NASA Astrophysics Data System (ADS)

Wu, S. Y.; Li, Y.; Chen, X. M.

2004-11-01

The Raman spectra and dielectric properties of Nd /Sn cosubstituted Ba6-3xSm8+2xTi18O54 (x =2/3) microwave dielectric ceramics were discussed as the functions of composition and sintering time. The peaks in 753cm-1 were caused by the second order scatter. The peaks in 425 and 403cm-1 became sharper with prolonging sintering time, and this reflected the increased lattice defects. The shoulder peak near 292cm-1 was caused by the octahedral tilt when A site is Nd3+. The Raman shifts in 590, 520, 280, and 232cm-1 indicated no obvious change in position, but all peaks became sharper with prolonging sintering time. This indicated the increased ordering degree of A-site cations. With prolonging sintering time, the Qf factor (Q is the inverse of dielectric loss, tan δ, and f is the resonant frequency) increased, and the temperature coefficient of resonant frequency significantly decreased or became more negative, while the dielectric constant indicated no significant variation.

Effects of La-doped BaSnO3epitaxial electrode on the ferroelectric properties of BaTiO3

NASA Astrophysics Data System (ADS)

Lee, Hahoon; Kim, Young Mo; Kim, Youjung; Shin, Juyeon; Char, Kookrin

In order to integrate the newly discovered high-mobility perovskite semiconductor BaSnO3 with a ferroelectric perovskite, we have grown epitaxial ferroelectric BaTiO3 (BTO) on top of the 4 % La-doped BaSnO3 (BLSO). X-ray diffraction measurement suggests that the BTO film on top of BLSO electrode is tensilely strained due to the larger lattice constant of BLSO. An all epitaxial sandwich structure of BLSO/BTO/BLSO was fabricated in order to measure the ferroelectric properties of the BTO under tensile strain. The polarization-electric field (P-E) hysteresis curve will be discussed from the viewpoint of the tensile strain. In addition, the breakdown field will be measured to evaluate the potential of BTO for a gate oxide on top of BLSO. Samsung science and technology foundation.

A 10 GHz Y-Ba-Cu-O/GaAs hybrid oscillator proximity coupled to a circular microstrip patch antenna

NASA Technical Reports Server (NTRS)

Rohrer, Norman J.; Richard, M. A.; Valco, George J.; Bhasin, Kul B.

1993-01-01

A 10 GHz hybrid Y-Ba-Cu-O / GaAs microwave oscillator proximity coupled to a circular microstrip antenna was designed, fabricated and characterized. The oscillator was a reflection mode type using a GaAs MESFET as the active element. The feedline, transmission lines, RF chokes, and bias lines were all fabricated from YBa2Cu3O(7-x) superconducting thin films on a 1 cm x 1 cm lanthanum aluminate substrate. The output feedline of the oscillator was wire bonded to a superconducting feedline on a second 1 cm x 1 cm lanthanum aluminate substrate, which was in turn proximity coupled to a circular microstrip patch antenna. Antenna patterns from this active patch antenna and the performance of the oscillator measured at 77 K are reported. The oscillator had a maximum output power of 11.5 dBm at 77 K, which corresponded to an efficiency of 10 percent. In addition, the efficiency of the microstrip patch antenna together with its high temperature superconducting feedline was measured from 85 K to 30 K and was found to be 71 percent at 77 4 increasing to a maximum of 87.4 percent at 30 K.

Pulsed Laser Deposition of BaCe(sub 0.85)Y(sub 0.15)0(sub 3) FILMS

NASA Technical Reports Server (NTRS)

Dynys, F. W.; Sayir, A.

2006-01-01

Pulsed laser deposition has been used to grow nanostructured BaCe(sub 0.85)Y(sub 0.15)0(sub 3) films. The objective is to enhance protonic conduction by reduction of membrane thickness. Sintered samples and laser targets were prepared by sintering BaCe(sub 0.85)Y(sub 0.15)O(sub 3) powders derived by solid state synthesis. Films 2 to 6 m thick were deposited by KrF excimer laser on Si and porous Al2O3 substrates. Nanocrystalline films were fabricated at deposition temperatures of 600-800 C deg at O2 pressure of 30 mTorr and laser fluence of 1.2 J/cm square. Films were characterized by x-ray diffraction, scanning electron microscopy and electrical impedance spectroscopy. Dense single phase BaCe(sub 0.85)Y((sub 0.15) 0(sub 3) films with a columnar growth morphology is observed, preferred crystal growth was found to be dependent upon deposition temperature and substrate type. Electrical conductivity of bulk samples produced by solid state sintering and thin film samples were measured over a temperature range of 100 C deg to 900 C deg in moist argon. Electrical conduction of the fabricated films was 1 to 4 orders of magnitude lower than the sintered bulk samples. With respect to the film growth direction, activation energy for electrical conduction is 3 times higher in the perpendicular direction than the parallel direction.

Synthesis of the complex fluoride LiBaF 3 and optical spectroscopy properties of LiBaF 3: M( M=Eu,Ce) through a solvothermal process

NASA Astrophysics Data System (ADS)

Hua, Ruinian; Lei, Bingfu; Xie, Demin; Shi, Chunshan

2003-11-01

The complex fluoride LiBaF 3 and LiBaF 3: M( M=Eu, Ce) is solvothermally synthesized at 180°C and characterized by means of X-ray powder diffraction, scanning electron microscopy, thermogravimetric analysis and infrared spectroscopy. In the solvothermal process, the solvents, molar ratios of initial mixtures and reaction temperature play important roles in the formation of products. The excitation and emission spectra of the LiBaF 3: M( M=Eu,Ce) have been measured by fluorescence spectrophotometer. In the LiBaF 3:Eu emission spectra, there is one sharp line emission located at 360 nm arising from f→ f transition of Eu 2+ in the host lattice, and typical doublet 5 d-4 f emission of Ce 3+ in LiBaF 3 powder is shown.

Biochemical characterisation of MdCXE1, a carboxylesterase from apple that is expressed during fruit ripening.

PubMed

Souleyre, Edwige J F; Marshall, Sean D G; Oakeshott, John G; Russell, Robyn J; Plummer, Kim M; Newcomb, Richard D

2011-05-01

Esters are an important component of apple (Malus×domestica) flavour. Their biosynthesis increases in response to the ripening hormone ethylene, but their metabolism by carboxylesterases (CXEs) is poorly understood. We have identified 16 members of the CXE multigene family from the commercial apple cultivar, 'Royal Gala', that contain all the conserved features associated with CXE members of the α/β hydrolase fold superfamily. The expression of two genes, MdCXE1 and MdCXE16 was characterised in an apple fruit development series and in a transgenic line of 'Royal Gala' (AO3) that is unable to synthesise ethylene in fruit. In wild-type MdCXE1 is expressed at low levels during early stages of fruit development, rising to a peak of expression in apple fruit at harvest maturity. It is not significantly up-regulated by ethylene in the skin of AO3 fruit. MdCXE16 is expressed constitutively in wild-type throughout fruit development, and is up-regulated by ethylene in skin of AO3 fruit. Semi-purified recombinant MdCXE1 was able to hydrolyse a range of 4-methyl umbelliferyl ester substrates that included those containing acyl moieties that are found in esters produced by apple fruit. Kinetic characterisation of MdCXE1 revealed that the enzyme could be inhibited by organophosphates and that its ability to hydrolyse esters showed increasing affinity (K(m)) but decreasing turnover (k(cat)) as substrate acyl carbon length increases from C2 to C16. Our results suggest that MdCXE1 may have an impact on apple flavour through its ability to hydrolyse relevant flavour esters in ripe apple fruit. Copyright © 2011 Elsevier Ltd. All rights reserved.

Fabrication and electrochemical performance of a stable, anode supported thin BaCe0.4Zr0.4Y0.2O3-δ electrolyte Protonic Ceramic Fuel Cell

NASA Astrophysics Data System (ADS)

Nasani, Narendar; Ramasamy, Devaraj; Mikhalev, Sergey; Kovalevsky, Andrei V.; Fagg, Duncan P.

2015-03-01

The present work deals with the fabrication and electrochemical characterisation of a potential protonic ceramic fuel cell based on a Ni-BaZr0.85Y0.15O3-δ anode supported thin film proton conducting BaCe0.4Zr0.4Y0.2O3-δ electrolyte with a Pr2NiO4+δ cathode. Anode and electrolyte materials were prepared by an acetate-H2O2 combustion method. A thin (∼5 μm), dense and crack free BaCe0.4Zr0.4Y0.2O3-δ electrolyte film was successfully obtained on a porous anode support by spin coating and firing at 1450 °C. Maximum power densities of 234, 158, 102 and 63 mW cm-2 at 700, 650, 600 and 550 °C, respectively were achieved for the Ni-BaZr0.85Y0.15O3-δ/BaCe0.4Zr0.4Y0.2O3-δ/Pr2NiO4+δ single cell under fuel cell testing conditions. Electrode polarisation resistance was assessed at open circuit conditions by use of electrochemical impedance spectroscopy (EIS) and is shown to dominate the area specific resistance at low temperatures. Postmortem analysis by scanning electron microscopy (SEM), reveals that no delamination occurs at anode/electrolyte or electrolyte/cathode interfaces upon cell operation.

High resolution FTIR spectroscopy of BaY2F8 single crystals doped with trivalent Er

NASA Astrophysics Data System (ADS)

Baraldi, A.; Capelletti, R.; Cornelli, M.; Ponzoni, A.; Ruffini, A.; Sperzagni, A.; Tonelli, M.

High resolution (0.04 cm-1) FTIR spectroscopy is applied to monoclinic Er3+-doped BaY2F8 single crystals in the wavenumber range 500-24000 cm-1 and temperature range 9-300 K to study the crystal field splitting of the fundamental 4I15/2 and of the excited 4I13/2, 4I11/2, 4I9/2, 4F9/2, 4S3/2, 2H11/2, 4F7/2, 4F5/2, and 4F3/2 states and the effects caused by increasing Er3+-concentrations (2-20% m.f.), such as inhomogeneous line-broadening and new lines due to Er3+-Er3+ interaction. In the framework of the electron-phonon interaction, the thermally induced line-broadening and -shift are detected and accounted for by the two-phonon Raman model and the vibronic replicas of a few lines are investigated.

Manganese Vanadate Chemistry in Hydrothermal BaF 2 Brines: Ba 3 Mn 2 (V 2 O 7 ) 2 F 2 and Ba 7 Mn 8 O 2 (VO 4 ) 2 F 23

DOE PAGES

Sanjeewa, Liurukara D.; McMillen, Colin D.; McGuire, Michael A.; ...

2016-12-05

We synthesized manganese vanadate fluorides using high-temperature hydrothermal techniques with BaF 2 as a mineralizer. Ba 3Mn 2(V 2O 7) 2F 2 crystallizes in space group C2/c and consists of dimers built from edge-sharing MnO 4F 2 trigonal prisms with linking V 2O 7 groups. Ba 7Mn 8O 2(VO 4) 2F 23 crystallizes in space group Cmmm, with a manganese oxyfluoride network built from edge- and corner-sharing Mn 2+/3+(O,F) 6 octahedra. The resulting octahedra form alternating Mn 2+ and Mn 2+/3+ layers separated by VO 4 tetrahedra. This latter compound exhibits a canted antiferromagnetic order below TN = 25 K.

Fabrication and electrical properties of (111) textured (Ba0.6Sr0.4)TiO3 film on platinized Si substrate

NASA Astrophysics Data System (ADS)

Wang, Yi; Liu, Baoting; Wei, Feng; Yang, Zhimin; Du, Jun

2007-01-01

The authors report the fabrication of (Ba0.6Sr0.4)TiO3 (BST) film on Pt /Si(001) substrate without Ti adhesion layer by magnetron sputtering. X-ray diffraction technique is used to characterize the orientation and phase purity of BST/Pt heterostructure. It is found that both BST and Pt films are (111) textured. The (111) BST films are observed to have high tunability of 49.4%; the dielectric constant and dielectric loss of the BST film are about 682 and 0.015, respectively. The leakage current density of BST film agrees well with the space-charge-limited current theory at room temperature and is only 3.90×10-8A/cm2 at 455kV/cm.

Effects of oxygen vacancy on the photoconductivity in BaSnO3

NASA Astrophysics Data System (ADS)

Park, Jisung; Char, Kookrin; Institute of Applied Physics, Department of Physics; Astronomy, Seoul National University Team

We have found the photoconductive behavior of BaSnO3, especially their magnitude and time dependence, is very sensitive to the oxygen vacancy concentration. We made epitaxial BaSnO3 film with BaHfO3 buffer layer by pulsed laser deposition. As we had reported before, MgO substrate with its large band gap size about 7.8 eV was used to exclude any photoconductance from the substrate. BaHfO3 layer was used to reduce the threading dislocation density in BaSnO3 film. To control the oxygen vacancy concentration in the BaSnO3 film, we annealed the sample in Ar or O2 atmosphere with varying annealing conditions. After each annealing process, photoconductivity of BaSnO3 was measured during illumination of UV light. The result showed that the magnitude of photoconductivity of BaSnO3 increased after annealing at higher temperature in Ar atmosphere, while the changes in the dark current remains minimal. The result can be explained by a hole trap mechanism. Higher Fermi level due to the increased oxygen vacancy concentration can cause occupation of deep acceptor levels in dislocations of the BaSnO3 film. These occupied deep acceptor levels in turn trap photo-generated holes so that the recombination of electron-hole pair is deterred. Samsung Science and Technology Foundation.

75 FR 1705 - Drawbridge Operation Regulations; Curtis Creek, Baltimore, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-13

..., mile 0.9, at Baltimore, MD. The deviation is necessary to facilitate mechanical repairs to the bridge... facilitate mechanical repairs. The I695 Bridge, a double-leaf bascule drawbridge, has a vertical clearance in...

78 FR 38001 - Special Local Regulations; Marine Events, Breton Bay; St. Mary's County, Leonardtown, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-25

...-AA08 Special Local Regulations; Marine Events, Breton Bay; St. Mary's County, Leonardtown, MD AGENCY... marine event to be held on the waters of Breton Bay in St. Mary's County, Maryland on July 13, 2013, and... ``Special Local Regulations; Marine Events, Breton Bay; St. Mary's County, Leonardtown, MD'' in the Federal...

The Structural Basis for Lipid and Endotoxin Binding in RP105-MD-1, and Consequences for Regulation of Host Lipopolysaccharide Sensitivity.

PubMed

Ortiz-Suarez, Maite L; Bond, Peter J

2016-01-05

MD-1 is a member of the MD-2-related lipid-recognition (ML) family, and associates with RP105, a cell-surface protein that resembles Toll-like receptor 4 (TLR4). The RP105⋅MD-1 complex has been proposed to play a role in fine-tuning the innate immune response to endotoxin such as bacterial lipopolysaccharide (LPS) via TLR4⋅MD-2, but controversy surrounds its mechanism. We have used atomically detailed simulations to reveal the structural basis for ligand binding and consequent functional dynamics of MD-1 and the RP105 complex. We rationalize reports of endogenous phospholipid binding, by showing that they prevent collapse of the malleable MD-1 fold, before refining crystallographic models and uncovering likely binding modes for LPS analogs. Subsequent binding affinity calculations reveal that endotoxin specificity arises from the entropic cost of expanding the MD-1 cavity to accommodate bulky lipid tails, and support the role of MD-1 as a "sink" that sequesters endotoxin from TLR4 and stabilizes RP105/TLR4 interactions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Superconductivity in the Sn-Ba-Sr-Y-Cu-O system

NASA Technical Reports Server (NTRS)

Aleksandrov, K. S.; Khrustalev, B. P.; Krivomazov, S. N.; Petrov, M. I.; Vasilyev, A. D.; Zwegintsev, S. A.

1991-01-01

After the discovery of high-T(sub c) superconductivity in the La-Ba-Cu-O compound, several families of superconducting oxides were synthesized. Here, researchers report the results of the search for superconductivity in the compounds based on tin which has a lone electron pair like Bi, Tl, and Pb. The following compounds were synthesized: Sn1Ba1Sr1Cu3O(sub x), Sn1Ba1Ca1Cu3O(sub x), Sn1Ba1Mg1Cu3O(sub x), Sn1Sr1Ca1Cu3O(sub x), Sn1Sr1Mg1Cu3O(sub x), and Sn1Ca1Mg1Cu3O(sub x). The initial components were oxides and carbonates of the appropriate elements. A standard firing-grinding procedure was used. Final heating was carried out at 960 C during 12 hours. Then the samples were cooled inside the furnace. All the synthesis cycles were carried out in air atmosphere. Among the synthesized compounds only Sn1Ba1Sr1Cu3O(sub x) showed remarkable conductivity. Other compounds were practically dielectrics. Presence of a possible superconductivity in Sn1Ba1Sr1Cu3O(sub x) was defined by using the Meissner effect. At low temperature a deviation from paramagnetic behavior is observed. The hysteresis loops obtained at lower temperature undoubtly testify to the presence of a superconductive phase in the sample. However, the part of the superconductive phase in the Sn1Ba1Sr1Cu3O(sub x) ceramic turned out to be small, less than 2 percent, which agrees with the estimation from magnetic data. In order to increase the content of the superconductive phase, two-valent cations Ba and Sr were partially substituted by univalent (K) and three-valent ones (Y).

Validity of the Medical College Admission Test for predicting MD-PhD student outcomes.

PubMed

Bills, James L; VanHouten, Jacob; Grundy, Michelle M; Chalkley, Roger; Dermody, Terence S

2016-03-01

The Medical College Admission Test (MCAT) is a quantitative metric used by MD and MD-PhD programs to evaluate applicants for admission. This study assessed the validity of the MCAT in predicting training performance measures and career outcomes for MD-PhD students at a single institution. The study population consisted of 153 graduates of the Vanderbilt Medical Scientist Training Program (combined MD-PhD program) who matriculated between 1963 and 2003 and completed dual-degree training. This population was divided into three cohorts corresponding to the version of the MCAT taken at the time of application. Multivariable regression (logistic for binary outcomes and linear for continuous outcomes) was used to analyze factors associated with outcome measures. The MCAT score and undergraduate GPA (uGPA) were treated as independent variables; medical and graduate school grades, time-to-PhD defense, USMLE scores, publication number, and career outcome were dependent variables. For cohort 1 (1963-1977), MCAT score was not associated with any assessed outcome, although uGPA was associated with medical school preclinical GPA and graduate school GPA (gsGPA). For cohort 2 (1978-1991), MCAT score was associated with USMLE Step II score and inversely correlated with publication number, and uGPA was associated with preclinical GPA (mspGPA) and clinical GPA (mscGPA). For cohort 3 (1992-2003), the MCAT score was associated with mscGPA, and uGPA was associated with gsGPA. Overall, MCAT score and uGPA were inconsistent or weak predictors of training metrics and career outcomes for this population of MD-PhD students.

MD and BCA simulations of He and H bombardment of fuzz in bcc elements

NASA Astrophysics Data System (ADS)

Klaver, T. P. C.; Zhang, S.; Nordlund, K.

2017-08-01

We present results of MD simulations of low energy He ion bombardment of low density fuzz in bcc elements. He ions can penetrate several micrometers into sparse fuzz, which allows for a sufficient He flux through it to grow the fuzz further. He kinetic energy falls off exponentially with penetration depth. A BCA code was used to carry out the same ion bombardment on the same fuzz structures as in MD simulations, but with simpler, 10 million times faster calculations. Despite the poor theoretical basis of the BCA at low ion energies, and the use of somewhat different potentials in MD and BCA calculations, the ion penetration depths predicted by BCA are only ∼12% less than those predicted by MD. The MD-BCA differences are highly systematic and trends in the results of the two methods are very similar. We have carried out more than 200 BCA calculation runs of ion bombardment of fuzz, in which parameters in the ion bombardment process were varied. For most parameters, the results show that the ion bombardment process is quite generic. The ion species (He or H), ion mass, fuzz element (W, Ta, Mo, Fe) and fuzz element lattice parameter turned out to have a modest influence on ion penetration depths at most. An off-normal angle of incidence strongly reduces the ion penetration depth. Increasing the ion energy increases the ion penetration, but the rate by which ion energy drops off at high ion energies follows the same exponential pattern as at lower energies.

Effect of barium titanate (BaTiO{sub 3}) additive on the short-term DC breakdown strength of polyethylene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khalil, M.S.; Henk, P.O.

1996-12-31

The use of additives to insulating materials is one of the methods to improve certain properties of these materials. Additives can also be used to provide more insight into some processes like conduction, space charge formation and breakdown under certain conditions of field application. In the present paper, the effect of the addition of fine particles 1 wt% BaTiO{sub 3} to plain low density polyethylene (LDPE) on the short-term dc breakdown strength of LDPE at room temperature was investigated. The characteristics of the used polyethylene are as follows: density 0.925 g/cm{sup 3}, melt index 0.25 g/10 min. The BaTiO{sub 3}more » used was laboratory grade with particle size less than 7 {micro}m. Special cylindrical test samples of both undoped and doped materials were used in this investigation. Stainless steel hemispherically tipped electrodes were embedded in the material by molding. The mean value of the gap length between the electrodes was 0.25 mm. The design of the test sample allows for determining the intrinsic breakdown strength of the material. The Weibull plots were used to analyze the breakdown test results. Analysis of the results indicate that the addition of BaTiO{sub 3} to LDPE has reduced the short term dc breakdown strength of the doped material by about 16% if compared with the corresponding value for the plain LDPE. An attempt is made to correlate between the present results, and earlier published results about the effect of BaTiO{sub 3} on dc conductivity and space charge formation in LDPE.« less

Electronic structure of BaNi2As2

NASA Astrophysics Data System (ADS)

Zhou, Bo; Xu, Min; Zhang, Yan; Xu, Gang; He, Cheng; Yang, L. X.; Chen, Fei; Xie, B. P.; Cui, Xiao-Yu; Arita, Masashi; Shimada, Kenya; Namatame, Hirofumi; Taniguchi, Masaki; Dai, X.; Feng, D. L.

2011-01-01

BaNi2As2, with a first-order phase transition around 131 K, is studied by the angle-resolved photoemission spectroscopy. The measured electronic structure is compared to the local-density approximation calculations, revealing similar large electronlike bands around M¯ and differences along Γ¯-X¯. We further show that the electronic structure of BaNi2As2 is distinct from that of the sibling iron pnictides. Particularly, there is no signature of band folding, indicating no collinear spin-density-wave-related magnetic ordering. Moreover, across the strong first-order phase transition, the band shift exhibits a hysteresis, which is directly related to the significant lattice distortion in BaNi2As2.

MD1003 (high-dose biotin) for the treatment of progressive multiple sclerosis: A randomised, double-blind, placebo-controlled study.

PubMed

Tourbah, Ayman; Lebrun-Frenay, Christine; Edan, Gilles; Clanet, Michel; Papeix, Caroline; Vukusic, Sandra; De Sèze, Jerome; Debouverie, Marc; Gout, Olivier; Clavelou, Pierre; Defer, Gilles; Laplaud, David-Axel; Moreau, Thibault; Labauge, Pierre; Brochet, Bruno; Sedel, Frédéric; Pelletier, Jean

2016-11-01

Treatment with MD1003 (high-dose biotin) showed promising results in progressive multiple sclerosis (MS) in a pilot open-label study. To confirm the efficacy and safety of MD1003 in progressive MS in a double-blind, placebo-controlled study. Patients (n = 154) with a baseline Expanded Disability Status Scale (EDSS) score of 4.5-7 and evidence of disease worsening within the previous 2 years were randomised to 12-month MD1003 (100 mg biotin) or placebo thrice daily, followed by 12-month MD1003 for all patients. The primary endpoint was the proportion of patients with disability reversal at month 9, confirmed at month 12, defined as an EDSS decrease of ⩾1 point (⩾0.5 for EDSS 6-7) or a ⩾20% decrease in timed 25-foot walk time compared with the best baseline among screening or randomisation visits. A total of 13 (12.6%) MD1003-treated patients achieved the primary endpoint versus none of the placebo-treated patients (p = 0.005). MD1003 treatment also reduced EDSS progression and improved clinical impression of change compared with placebo. Efficacy was maintained over follow-up, and the safety profile of MD1003 was similar to that of placebo. MD1003 achieves sustained reversal of MS-related disability in a subset of patients with progressive MS and is well tolerated. © The Author(s), 2016.

Transport properties of layered Ba(Pb,Bi)O3 thin films

NASA Astrophysics Data System (ADS)

Hassink, G. W. J.; Munakata, K.; Hammond, R. H.; Beasley, M. R.

2012-02-01

Doped BaBiO3 is a 3D oxide superconductor with a maximum Tc of 30 K for Ba0.6K0.4BiO3. There has been a lot of discussion on whether this high Tc can be explained purely by electron-phonon coupling with a high coupling constant λ. In addition, the presence of real-space paired 6s^2 electrons in the parent compound raise intriguing questions about whether there is an electron-electron coupling interaction as well. This possible negative-U interaction might be used to implement the suggestion by Berg, Orgad and Kivelson [Phys.Rev.B 78, 094509] that for a two-layer system where one layer provides electron pairing interaction and the other layer is conducting, the whole can be superconducting with a high Tc. Here we discuss the transport properties of BaPbO3/BaBiO3 bilayers, where the BaBiO3 layer is thought to act as the pairing layer, while the BaPbO3 acts as the conducting layer. The transport behavior changes to insulating upon decreasing the metallic BaPbO3 layer thickness at values that single films are expected to still be metallic.

Snynthesis and magnetization of BaLn2O4 (Ln = lanthanide)

NASA Astrophysics Data System (ADS)

Lundberg, Matthew

The BaLn2O4 family has been synthesized successfully as single crystals by the flux-growth method. The phases crystallize in the CaV2O4 structure prototype in space group Pnma (# 62). The structure has been studied using single-crystal x-ray diffraction, and stoichiometry confirmed with EDS, and the unit cell parameters and atomic positions have been determined for the whole lanthanide series (with the exception of the Lu compound). The effects of the lanthanide ionic radius on the atomic positions in the unit cell has been studied in terms of fractional atomic coordinates, bond lengths and angles, and bond valence sums. Magnetic measurements have been performed on the series with the exception of the La, Eu, and Lu members in the form of susceptibility versus temperature. The crystals all show signs of geometric antiferromagnetic frustration with the Neel temperatures significantly below the temperature predicted by the Weiss constant. Additionally some members of the family, namely BaCe2O4, BaNd2O4, BaPr 2O4, BaSm2O4, BaTb2O 4, and BaYb2O4 show significant crystal field splitting, that causes deviation from Currie-Weiss behavior.

United Nations’ Operation in Somalia: The Possibility of Success With a Different Approach or Application

DTIC Science & Technology

2002-05-31

by ABUL FAZAL MD SANAULLAH, MAJ, BANGLADESH ARMY B.A., Chittagong University, Bangladesh, 1988 M.D.S., National University, Bangladesh, 2000 Fort...Candidate: Major Abul Fazal Md Sanaullah Thesis Title: United Nations’ Operation in Somalia: Possibility of Success Approved by...APPLICATION, by Major Abul Fazal Md Sanaullah, 136 pages. This study examines whether the UN Operation in Somalia could have succeeded with a different

The cold-induced basic helix-loop-helix transcription factor gene MdCIbHLH1 encodes an ICE-like protein in apple

PubMed Central

2012-01-01

Background Plant growth is greatly affected by low temperatures, and the expression of a number of genes is induced by cold stress. Although many genes in the cold signaling pathway have been identified in Arabidopsis, little is known about the transcription factors involved in the cold stress response in apple. Results Here, we show that the apple bHLH (basic helix-loop-helix) gene MdCIbHLH1 (Cold-Induced bHLH1), which encodes an ICE-like protein, was noticeably induced in response to cold stress. The MdCIbHLH1 protein specifically bound to the MYC recognition sequences in the AtCBF3 promoter, and MdCIbHLH1 overexpression enhanced cold tolerance in transgenic Arabidopsis. In addition, the MdCIbHLH1 protein bound to the promoters of MdCBF2 and favorably contributed to cold tolerance in transgenic apple plants by upregulating the expression of MdCBF2 through the CBF (C-repeat-binding factor) pathway. Our findings indicate that MdCIbHLH1 functions in stress tolerance in different species. For example, ectopic MdCIbHLH1 expression conferred enhanced chilling tolerance in transgenic tobacco. Finally, we observed that cold induces the degradation of the MdCIbHLH1 protein in apple and that this degradation was potentially mediated by ubiquitination and sumoylation. Conclusions Based on these findings, MdCIbHLH1 encodes a transcription factor that is important for the cold tolerance response in apple. PMID:22336381

Re-induced Raman active modes in HgBa2Can-1CunO2n+2+δ compounds

NASA Astrophysics Data System (ADS)

Poulakis, N.; Lampakis, D.; Liarokapis, E.; Yoshikawa, Akira; Shimoyama, Jun-Ich; Kishio, Kohji; Peacock, G. B.; Hodges, J. P.; Gameson, I.; Edwards, P. P.; Panagopoulos, C.

1999-08-01

A comparative Raman study of Re-free and Re-doped HgBa2Can-1CunO2n+2+δ with n=1,3,4,5 is presented in an attempt to further clarify the structural and phononic modifications brought about by Re substitution. A number of extra high-frequency phonon peaks show up in the spectra of the Re-doped samples and are attributed to the oxygen modes of a strongly bound, almost decoupled ReO6 octahedron. As regards the apex oxygen in the Hg site, a clear transfer of spectral weight from the 590 to the 570 cm-1 apex phonon band is observed upon Re substitution. Such a change may well be accounted for assuming increased excess oxygen content for the Re-doped samples. Another interesting result is the enhancement upon Re doping of a narrow peak probably attributed to c-axis vibrations of Ba whose frequency shows a distinctive change with the number n of the CuO2 layers, providing an easy way to identify the various phases in a sample.

Competing exchange interactions in multiferroic and ferrimagnetic CaBaCo 4 O 7

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fishman, Randy Scott; Bordacs, S.; Kocsis, Vilmos

Competing exchange interactions can produce complex magnetic states together with spin-induced electric polarizations. With competing interactions on alternating triangular and kagome layers, the swedenborgite CaBaCo 4O 7 may have one of the largest measured spin-induced polarizations of ~1700 nC/cm 2 below its ferrimagnetic transition temperature at 70 K. Upon rotating our sample about c = [0,0,1] while the magnetic field is fixed along [1,0,0], the threefold splitting of the spin-wave frequencies indicates that our sample is hexagonally twinned. In addition, magnetization measurements then suggest that roughly 20% of the sample is in a domain with the a axis along [1,0,0]more » and that 80% of the sample is in one of two other domains with the a axis along either [-1/2,√3/2, 0] or [-1/2, -√3/2, 0] . Powder neutron-diffraction data, magnetization measurements, and terahertz (THz) absorption spectroscopy reveal that the complex spin order in each domain can be described as a triangular array of bitetrahedral c-axis chains ferrimagnetically coupled to each other in the ab plane. In conclusion, the electric-field dependence of bonds coupling those chains produces the large spin-induced polarization of CaBaCo 4O 7 .« less

Competing exchange interactions in multiferroic and ferrimagnetic CaBaCo 4 O 7

DOE PAGES

Fishman, Randy Scott; Bordacs, S.; Kocsis, Vilmos; ...

2017-01-23

Competing exchange interactions can produce complex magnetic states together with spin-induced electric polarizations. With competing interactions on alternating triangular and kagome layers, the swedenborgite CaBaCo 4O 7 may have one of the largest measured spin-induced polarizations of ~1700 nC/cm 2 below its ferrimagnetic transition temperature at 70 K. Upon rotating our sample about c = [0,0,1] while the magnetic field is fixed along [1,0,0], the threefold splitting of the spin-wave frequencies indicates that our sample is hexagonally twinned. In addition, magnetization measurements then suggest that roughly 20% of the sample is in a domain with the a axis along [1,0,0]more » and that 80% of the sample is in one of two other domains with the a axis along either [-1/2,√3/2, 0] or [-1/2, -√3/2, 0] . Powder neutron-diffraction data, magnetization measurements, and terahertz (THz) absorption spectroscopy reveal that the complex spin order in each domain can be described as a triangular array of bitetrahedral c-axis chains ferrimagnetically coupled to each other in the ab plane. In conclusion, the electric-field dependence of bonds coupling those chains produces the large spin-induced polarization of CaBaCo 4O 7 .« less

Preparation of thin-film (Ba(0.5),Sr(0.5))TiO3 by the laser ablation technique and electrical properties

NASA Astrophysics Data System (ADS)

Yoon, Soon-Gil; Lee, Jai-Chan; Safari, A.

1994-09-01

The chemical composition and electrical properties were investigated for epitaxially crystallized (Ba(0.5),Sr(0.5))TiO3 (BST) films deposited on Pt/MgO and YBa2Cu3O(7-x) (YBCO)/MgO substrates by the laser ablation technique. Rutherford backscattering spectroscopy analysis shows that thin films on Pt/MgO have almost the same stoichiometric composition as the target material. Films deposited at 600 C exhibited an excellent epitaxial growth, a dielectric constant of 430, and a dissipation factor of 0.02 at 10 kHz frequency. They have a charge storage density of 40 fC/sq micron at an applied electric field of 0.15 MV/cm. Leakage current density of BST thin films on Pt/MgO was smaller than on YBCO/MgO. Their leakage current density is about 0.8 microA/sq cm at an applied electric field of 0.15 MV/cm.

The 226Ra-Ba relationship in the North Atlantic during GEOTRACES-GA01

NASA Astrophysics Data System (ADS)

Le Roy, Emilie; Sanial, Virginie; Charette, Matthew A.; van Beek, Pieter; Lacan, François; Jacquet, Stéphanie H. M.; Henderson, Paul B.; Souhaut, Marc; García-Ibáñez, Maribel I.; Jeandel, Catherine; Pérez, Fiz F.; Sarthou, Géraldine

2018-05-01

We report detailed sections of radium-226 (226Ra, T1/2 = 1602 years) activities and barium (Ba) concentrations determined in the North Atlantic (Portugal-Greenland-Canada) in the framework of the international GEOTRACES program (GA01 section - GEOVIDE project, May-July 2014). Dissolved 226Ra and Ba are strongly correlated along the section, a pattern that may reflect their similar chemical behavior. Because 226Ra and Ba have been widely used as tracers of water masses and ocean mixing, we investigated their behavior more thoroughly in this crucial region for thermohaline circulation, taking advantage of the contrasting biogeochemical patterns existing along the GA01 section. We used an optimum multiparameter (OMP) analysis to distinguish the relative importance of physical transport (water mass mixing) from nonconservative processes (sedimentary, river or hydrothermal inputs, uptake by particles and dissolved-particulate dynamics) on the 226Ra and Ba distributions in the North Atlantic. Results show that the measured 226Ra and Ba concentrations can be explained by conservative mixing for 58 and 65 % of the samples, respectively, notably at intermediate depth, away from the ocean interfaces. 226Ra and Ba can thus be considered conservative tracers of water mass transport in the ocean interior on the space scales considered here, namely, on the order of a few thousand kilometers. However, regions in which 226Ra and Ba displayed nonconservative behavior and in some cases decoupled behaviors were also identified, mostly at the ocean boundaries (seafloor, continental margins and surface waters). Elevated 226Ra and Ba concentrations found in deepwater in the West European Basin suggest that lower Northeast Atlantic Deep Water (NEADWl) accumulates 226Ra and Ba from sediment diffusion and/or particle dissolution during transport. In the upper 1500 m of the West European Basin, deficiencies in 226Ra and Ba are likely explained by their incorporation in planktonic calcareous

Neurology Falls. Patient Falls Risk Assessment, Neurology Clinic, Johns Hopkins Hospital, Baltimore, MD

DTIC Science & Technology

2009-07-06

currently valid ()MB control number. PLEASE DO NOT RETURN YOf IR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) 21 JUL 2008 2. REPORT TYPE Final...Hospital, Baltimore, MD 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) LT John M Gardner, MSC, USN 5d. PROJECT...NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) Johns Hopkins Hospital, Baltimore, MD Residency Site

77 FR 22523 - Safety Zone; 2012 Ocean City Air Show; Atlantic Ocean, Ocean City, MD

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-16

...-AA00 Safety Zone; 2012 Ocean City Air Show; Atlantic Ocean, Ocean City, MD AGENCY: Coast Guard, DHS... the navigable waters of the Atlantic Ocean in Ocean City, MD. This action is necessary to provide for the safety of life on navigable waters during the 2012 Ocean City Air Show. This action is intended to...

MD Simulations of tRNA and Aminoacyl-tRNA Synthetases: Dynamics, Folding, Binding, and Allostery

PubMed Central

Li, Rongzhong; Macnamara, Lindsay M.; Leuchter, Jessica D.; Alexander, Rebecca W.; Cho, Samuel S.

2015-01-01

While tRNA and aminoacyl-tRNA synthetases are classes of biomolecules that have been extensively studied for decades, the finer details of how they carry out their fundamental biological functions in protein synthesis remain a challenge. Recent molecular dynamics (MD) simulations are verifying experimental observations and providing new insight that cannot be addressed from experiments alone. Throughout the review, we briefly discuss important historical events to provide a context for how far the field has progressed over the past few decades. We then review the background of tRNA molecules, aminoacyl-tRNA synthetases, and current state of the art MD simulation techniques for those who may be unfamiliar with any of those fields. Recent MD simulations of tRNA dynamics and folding and of aminoacyl-tRNA synthetase dynamics and mechanistic characterizations are discussed. We highlight the recent successes and discuss how important questions can be addressed using current MD simulations techniques. We also outline several natural next steps for computational studies of AARS:tRNA complexes. PMID:26184179