Estimation of vegetation parameters such as Leaf Area Index from polarimetric SAR data

NASA Astrophysics Data System (ADS)

Hetz, Marina; Blumberg, Dan G.; Rotman, Stanley R.

2010-05-01

This work presents the analysis of the capability to use the radar backscatter coefficient in semi-arid zones to estimate the vegetation crown in terms of Leaf Area Index (LAI). The research area is characterized by the presence of a pine forest with shrubs as an underlying vegetation layer (understory), olive trees, natural grove areas and eucalyptus trees. The research area was imaged by an airborne RADAR system in L-band during February 2009. The imagery includes multi-look radar images. All the images were fully polarized i.e., HH, VV, HV polarizations. For this research we used the central azimuth angle (113° ). We measured LAI using the ?T Sun Scan Canopy Analysis System. Verification was done by analytic calculations and digital methods for the leaf's and needle's surface area. In addition, we estimated the radar extinction coefficient of the vegetation volume by comparing point calibration targets (trihedral corner reflectors with 150cm side length) within and without the canopy. The radar extinction in co- polarized images was ~26dB and ~24dB for pines and olives respectively, compared to the same calibration target outside the vegetation. We used smaller trihedral corner reflectors (41cm side length) and covered them with vegetation to measure the correlation between vegetation density, LAI and radar backscatter coefficient for pines and olives under known conditions. An inverse correlation between the radar backscatter coefficient of the trihedral corner reflectors covered by olive branches and the LAI of those branches was observed. The correlation between LAI and the optical transmittance was derived using the Beer-Lambert law. In addition, comparing this law's principle to the principle of the radar backscatter coefficient production, we derived the equation that connects between the radar backscatter coefficient and LAI. After extracting the radar backscatter coefficient of forested areas, all the vegetation parameters were used as inputs for the MIMICS model that simulates the radar backscatter coefficient of pines. The model results show a backscatter of -18dB in HV polarization which is 13dB higher than the mean pines backscatter in the radar images, whereas the co-polarized images revealed a backscatter of -10dB which is 23dB higher than the actual backscatter value deriver from the radar images. Therefore, next step in the research will incorporate other vegetation parameters and attempt to understand the discrepancies between the simulation and the actual data.

Quantitative broadband ultrasonic backscatter - An approach to nondestructive evaluation in acoustically inhomogeneous materials

NASA Technical Reports Server (NTRS)

Odonnell, M.; Miller, J. G.

1981-01-01

The use of a broadband backscatter technique to obtain the frequency dependence of the longitudinal-wave ultrasonic backscatter coefficient from a collection of scatterers in a solid is investigated. Measurements of the backscatter coefficient were obtained over the range of ultrasonic wave vector magnitude-glass sphere radius product between 0.1 and 3.0 from model systems consisting of dilute suspensions of randomly distributed crown glass spheres in hardened polyester resin. The results of these measurements were in good agreement with theoretical prediction. Consequently, broadband measurements of the ultrasonic backscatter coefficient may represent a useful approach toward characterizing the physical properties of scatterers in intrinsically inhomogeneous materials such as composites, metals, and ceramics, and may represent an approach toward nondestructive evaluation of these materials.

[Differences of inherent optical properties of inland lake water body in typical seasons].

PubMed

Sun, De-Yong; Li, Yun-Mei; Wang, Qiao; Le, Cheng-Fen; Huang, Chang-Chun; Wang, Li-Zhen

2008-05-01

Inherent optical property is one of the important properties of water body, which lays the foundation for the establishment of water color analytical models. By using quantity filter technology (QFT) and BB9 backscattering meter, the absorption coefficients of chromophoric dissolved organic matter (CDOM) and total suspended matters (TSM) and the backscattering coefficient of TSM in the water body at Meiliang Bay of Taihu Lake were measured in summer and winter. Based on the spectral comparison of the absorption and backscattering coefficients, their differences between the two seasons were demonstrated, and the reasons that caused these differences were also explored in the context of their relations to the changes in water quality. Consequently, water environment condition could be revealed by using the inherent optical property. The relationship between the backscattering coefficient and the TSM concentration was established, which could provide supporting coefficients to the analytical models to be developed.

Airborne Polarized Lidar Detection of Scattering Layers in the Ocean

NASA Astrophysics Data System (ADS)

Vasilkov, Alexander P.; Goldin, Yury A.; Gureev, Boris A.; Hoge, Frank E.; Swift, Robert N.; Wright, C. Wayne

2001-08-01

A polarized lidar technique based on measurements of waveforms of the two orthogonal-polarized components of the backscattered light pulse is proposed to retrieve vertical profiles of the seawater scattering coefficient. The physical rationale for the polarized technique is that depolarization of backscattered light originating from a linearly polarized laser beam is caused largely by multiple small-angle scattering from particulate matter in seawater. The magnitude of the small-angle scattering is determined by the scattering coefficient. Therefore information on the vertical distribution of the scattering coefficient can be derived potentially from measurements of the timedepth dependence of depolarization in the backscattered laser pulse. The polarized technique was verified by field measurements conducted in the Middle Atlantic Bight of the western North Atlantic Ocean that were supported by in situ measurements of the beam attenuation coefficient. The airborne polarized lidar measured the timedepth dependence of the backscattered laser pulse in two orthogonal-polarized components. Vertical profiles of the scattering coefficient retrieved from the timedepth depolarization of the backscattered laser pulse were compared with measured profiles of the beam attenuation coefficient. The comparison showed that retrieved profiles of the scattering coefficient clearly reproduce the main features of the measured profiles of the beam attenuation coefficient. Underwater scattering layers were detected at depths of 2025 m in turbid coastal waters. The improvement in dynamic range afforded by the polarized lidar technique offers a strong potential benefit for airborne lidar bathymetric applications.

Microultrasound characterisation of ex vivo porcine tissue for ultrasound capsule endoscopy

NASA Astrophysics Data System (ADS)

Lay, H. S.; Cox, B. F.; Sunoqrot, M.; Démoré, C. E. M.; Näthke, I.; Gomez, T.; Cochran, S.

2017-01-01

Gastrointestinal (GI) disease development and progression is often characterised by cellular and tissue architectural changes within the mucosa and sub-mucosa layers. Current clinical capsule endoscopy and other approaches are heavily reliant on optical techniques which cannot detect disease progression below the surface layer of the tissue. To enhance the ability of clinicians to detect cellular changes earlier and more confidently, both quantitative and qualitative microultrasound (μUS) techniques are investigated in healthy ex vivo porcine GI tissue. This work is based on the use of single-element, focussed μUS transducers made with micromoulded piezocomposite operating at around 48 MHz. To explore the possibility that μUS can detect Crohn’s disease and other inflammatory bowel diseases, ex vivo porcine small bowel tissue samples were cannulised and perfused with phosphate-buffered saline followed by various dilutions of polystyrene microspheres. Comparison with fluorescent imaging showed that the microspheres had infiltrated the microvasculature of the samples and that μUS was able to successfully detect this as a mimic of inflammation. Samples without microspheres were analysed using quantitative ultrasound to assess mechanical properties. Attenuation coefficients of 1.78 ± 0.66 dB/mm and 1.92 ± 0.77 dB/mm were obtained from reference samples which were surgically separated from the muscle layer. Six intact samples were segmented using a software algorithm and the acoustic impedance, Z, for varying tissue thicknesses, and backscattering coefficient, BSC, were calculated using the reference attenuation values and tabulated.

Laser remote sensing of tropospheric aerosol over Southern Ireland using a backscatter Raman LIDAR

NASA Astrophysics Data System (ADS)

Ruth, Albert A.; Acheson, Karen; Apituley, Arnoud; Chaikovsky, Anatoli; Nicolae, Doina; Ortiz-Amezcua, Pablo; Stoyanov, Dimitar; Trickl, Thomas

2016-04-01

Raman backscatter coefficients, extinction coefficients and lidar ratios were measured with a ground based Raman lidar system at University College Cork, Ireland, during the periods of July 2012 - August 2012, April 2013 - December 2013 and March 2014 - May 2014. Statistical analysis of these parameters in this time provided information about seasonal effects of Raman backscatter coefficients and the altitude of the top of the planetary boundary layer. The mean of the altitude of the top of the planetary boundary layer over these time periods is 950 ± 302 m. The values are larger in summer, 1206 ± 367 m, than in winter, 735 m. The altitude of the top of the planetary boundary layer measured at Cork is lower than most EARLINET stations. Raman backscatter coefficients above and altitude of 2 km are highest in summer and spring where the values are greater than 0.28 Mm-1 sr-1. Winter values of Raman backscatter coefficient are less than 0.06 Mm-1 sr-1. These seasonal effects are consistent with most EARLINET stations. Large aerosol loads were detected in July 2013 due to a Canadian forest fire event. HYSPLIT air-mass back trajectory models were used to trace the origin of the detected aerosol layers. The aerosol forecast model, MACC, was used to further investigate and verify the propagation of the smoke. The Lidar ratio values and Klett and Raman backscatter coefficients at Cork, for the 4th July, the 7th to 9th of July and the 11th July were compared with observations at Cabauw, Minsk, Granada, Bucharest, Sofia and Garmisch. Lidar ratio values for the smoke detected at Cork were determined to be between 33 sr and 62 sr. The poster will discuss the seasonal changes of Raman backscatter coefficients and the altitude of the top of the planetary boundary layer at Cork. An investigation of a Canadian forest fire event measured at Cork will be compared with other data from the EARLINET database.

Calculations of radar backscattering coefficient of vegetation-covered soils

NASA Technical Reports Server (NTRS)

Mo, T.; Schmugge, T. J.; Jackson, T. J. (Principal Investigator)

1983-01-01

A model for simulating the measured backscattering coefficient of vegetation-covered soil surfaces includes both coherent and incoherent components of the backscattered radar pulses from a rough sil surface. The effect of vegetation canopy scattering is also incorporated into the model by making the radar pulse subject to two-way attenuation and volume scattering when it passes through the vegetation layer. Model results agree well with the measured angular distributions of the radar backscattering coefficient for HH polarization at the 1.6 GHz and 4.75 GHz frequencies over grass-covered fields. It was found that the coherent scattering component is very important at angles near nadir, while the vegetation volume scattering is dominant at incident angles 30 degrees.

Wavelength dependence of aerosol backscatter coefficients obtained by multiple wavelength Lidar measurements

NASA Technical Reports Server (NTRS)

Sasano, Y.; Browell, E. V.

1986-01-01

Aerosols are often classified into several general types according to their origins and composition, such as maritime, continental, and stratospheric aerosols, and these aerosol types generally have different characteristics in chemical and physical properties. The present study aims at demonstrating the potential for distinguishing these aerosol types by the wavelength dependence of their backscatter coefficients obtained from quantitative analyses of multiple wavelength lidar signals. Data from the NASA Airborne Differential Abosrption lidar (DIAL) S ystems, which can measure aerosol backscatter profiles at wavelenghts of 300, 600, and 1064 nm and ozone profiles of backscatter coefficients for these three wavelength were derived from the observations of aerosols of different types. Observations were performed over the Atlantic Ocean, the Southwestern United States, and French Guyana.

Application of neural network to remote sensing of soil moisture using theoretical polarimetric backscattering coefficients

NASA Technical Reports Server (NTRS)

Wang, L.; Shin, R. T.; Kong, J. A.; Yueh, S. H.

1993-01-01

This paper investigates the potential application of neural network to inversion of soil moisture using polarimetric remote sensing data. The neural network used for the inversion of soil parameters is multi-layer perceptron trained with the back-propagation algorithm. The training data include the polarimetric backscattering coefficients obtained from theoretical surface scattering models together with an assumed nominal range of soil parameters which are comprised of the soil permittivity and surface roughness parameters. Soil permittivity is calculated from the soil moisture and the assumed soil texture based on an empirical formula at C-, L-, and P-bands. The rough surface parameters for the soil surface, which is described by the Gaussian random process, are the root-mean-square (rms) height and correlation length. For the rough surface scattering, small perturbation method is used for the L-band frequency, and Kirchhoff approximation is used for the C-band frequency to obtain the corresponding backscattering coefficients. During the training, the backscattering coefficients are the inputs to the neural net and the output from the net are compared with the desired soil parameters to adjust the interconnecting weights. The process is repeated for each input-output data entry and then for the entire training data until convergence is reached. After training, the backscattering coefficients are applied to the trained neural net to retrieve the soil parameters which are compared with the desired soil parameters to verify the effectiveness of this technique. Several cases are examined. First, for simplicity, the correlation length and rms height of the soil surface are fixed while soil moisture is varied. Soil moisture obtained using the neural networks with either L-band or C-band backscattering coefficients for the HH and VV polarizations as inputs is in good agreement with the desired soil moisture. The neural net output matches the desired output for the soil moisture range of 16 to 60 percent for the C-band case. The next case investigated is to vary both soil moisture and rms height while keeping the correlation length fixed. For this case, C-band backscattering coefficients are not sufficient for retrieving two parameters because the Kirchhoff approximation gives the same HH and VV backscattering coefficients. Therefore, the backscattering coefficients at two different frequency bands are necessary to find both the soil moisture and rms height. Finally, the neural nets are also applied to simultaneously invert soil moisture, rms height, and correlation length. Overall, the soil moisture retrieved from the neural network agrees very well with the desired soil moisture. This suggests that the neural network shows potential for retrieval of soil parameters from remote sensing data.

Spectral dependence of backscattering coefficient of mixed phase clouds over West Africa measured with two-wavelength Raman polarization lidar: Features attributed to ice-crystals corner reflection

NASA Astrophysics Data System (ADS)

Veselovskii, I.; Goloub, P.; Podvin, T.; Tanre, D.; Ansmann, A.; Korenskiy, M.; Borovoi, A.; Hu, Q.; Whiteman, D. N.

2017-11-01

The existing models predict that corner reflection (CR) of laser radiation by simple ice crystals of perfect shape, such as hexagonal columns or plates, can provide a significant contribution to the ice cloud backscattering. However in real clouds the CR effect may be suppressed due to crystal deformation and surface roughness. In contrast to the extinction coefficient, which is spectrally independent, consideration of diffraction associated with CR results in a spectral dependence of the backscattering coefficient. Thus measuring the spectral dependence of the cloud backscattering coefficient, the contribution of CR can be identified. The paper presents the results of profiling of backscattering coefficient (β) and particle depolarization ratio (δ) of ice and mixed-phase clouds over West Africa by means of a two-wavelength polarization Mie-Raman lidar operated at 355 nm and 532 nm during the SHADOW field campaign. The lidar observations were performed at a slant angle of 43 degree off zenith, thus CR from both randomly oriented crystals and oriented plates could be analyzed. For the most of the observations the cloud backscatter color ratio β355/β532 was close to 1.0, and no spectral features that might indicate the presence of CR of randomly oriented crystals were revealed. Still, in two measurement sessions we observed an increase of backscatter color ratio to a value of nearly 1.3 simultaneously with a decrease of the spectral depolarization ratio δ355/δ532 ratio from 1.0 to 0.8 inside the layers containing precipitating ice crystals. We attribute these changes in optical properties to corner reflections by horizontally oriented ice plates.

Atmospheric aerosol backscatter measurements using a tunable coherent CO2 lidar

NASA Technical Reports Server (NTRS)

Menzies, R. T.; Kavaya, M. J.; Flamant, P. H.; Haner, D. A.

1984-01-01

Measurements of atmospheric aerosol backscatter coefficients, using a coherent CO2 lidar at 9.25- and 10.6-micron wavelengths, are described. Vertical profiles of the volume backscatter coefficient beta have been measured to a 10-km altitude over the Pasadena, CA, region. These measurements indicate a wide range of variability in beta both in and above the local boundary layer. Certain profiles also indicate a significant enhancement in beta at the 9.25-micron wavelength compared with beta at the 10.6-micron wavelength, which possibly indicates a major contribution to the volume backscatter from ammonium sulfate aerosol particles.

Seasonal variations of the backscattering coefficient measured by radar altimeters over the Antarctic Ice Sheet

NASA Astrophysics Data System (ADS)

Ibrahime Adodo, Fifi; Remy, Frédérique; Picard, Ghislain

2018-05-01

Spaceborne radar altimeters are a valuable tool for observing the Antarctic Ice Sheet. The radar wave interaction with the snow provides information on both the surface and the subsurface of the snowpack due to its dependence on the snow properties. However, the penetration of the radar wave within the snowpack also induces a negative bias on the estimated surface elevation. Empirical corrections of this space- and time-varying bias are usually based on the backscattering coefficient variability. We investigate the spatial and seasonal variations of the backscattering coefficient at the S (3.2 GHz ˜ 9.4 cm), Ku (13.6 GHz ˜ 2.3 cm) and Ka (37 GHz ˜ 0.8 cm) bands. We identified that the backscattering coefficient at Ku band reaches a maximum in winter in part of the continent (Region 1) and in the summer in the remaining (Region 2), while the evolution at other frequencies is relatively uniform over the whole continent. To explain this contrasting behavior between frequencies and between regions, we studied the sensitivity of the backscattering coefficient at three frequencies to several parameters (surface snow density, snow temperature and snow grain size) using an electromagnetic model. The results show that the seasonal cycle of the backscattering coefficient at Ka frequency is dominated by the volume echo and is mainly driven by snow temperature evolution everywhere. In contrast, at S band, the cycle is dominated by the surface echo. At Ku band, the seasonal cycle is dominated by the volume echo in Region 1 and by the surface echo in Region 2. This investigation provides new information on the seasonal dynamics of the Antarctic Ice Sheet surface and provides new clues to build more accurate corrections of the radar altimeter surface elevation signal in the future.

Sci—Fri PM: Dosimetry—05: Megavoltage electron backscatter: EGSnrc results versus 21 experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ali, E. S. M.; The Ottawa Hospital Cancer Centre, Ottawa; Buchenberg, W.

2014-08-15

The accuracy of electron backscatter calculations at megavoltage energies is important for many medical physics applications. In this study, EGSnrc calculations of megavoltage electron backscatter (1–22 MeV) are performed and compared to the data from 21 experiments published between 1954 and 1993 for 25 single elements with atomic numbers from 3 to 92. Typical experimental uncertainties are 15%. For EGSnrc simulations, an ideal detector is assumed, and the most accurate electron physics options are employed, for a combined statistical and systematic uncertainty of 3%. The quantities compared are the backscatter coefficient and the energy spectra (in the backward hemisphere andmore » at specific detector locations). For the backscatter coefficient, the overall agreement is within ±2% in the absolute value of the backscatter coefficient (in per cent), and within 11% of the individual backscatter values. EGSnrc results are systematically on the higher end of the spread of the experimental data, which could be partially from systematic experimental errors discussed in the literature. For the energy spectra, reasonable agreement between simulations and experiments is observed, although there are significant variations in the experimental data. At the lower end of the spectra, simulations are higher than some experimental data, which could be due to reduced experimental sensitivity to lower energy electrons and/or over-estimation by EGSnrc for backscattered secondary electrons. In conclusion, overall good agreement is observed between EGSnrc backscatter calculations and experimental measurements for megavoltage electrons. There is a need for high quality experimental data for the energy spectra of backscattered electrons.« less

High-frequency attenuation and backscatter measurements of rat blood between 30 and 60 MHz.

PubMed

Huang, Chih-Chung

2010-10-07

There has recently been a great deal of interest in noninvasive high-frequency ultrasound imaging of small animals such as rats due to their being the preferred animal model for gene therapy and cancer research. Improving the interpretation of the obtained images and furthering the development of the imaging devices require a detailed knowledge of the ultrasound attenuation and backscattering of biological tissue (e.g. blood) at high frequencies. In the present study, the attenuation and backscattering coefficients of the rat red blood cell (RBC) suspensions and whole blood with hematocrits ranging from 6% to 40% were measured between 30 and 60 MHz using a modified substitution approach. The acoustic parameters of porcine blood under the same conditions were also measured in order to compare differences in the blood properties between these two animals. For porcine blood, both whole blood and RBC suspension were stirred at a rotation speed of 200 rpm. Three different rotation speeds of 100, 200 and 300 rpm were carried out for rat blood experiments. The attenuation coefficients of both rat and porcine blood were found to increase linearly with frequency and hematocrit (the values of coefficients of determination (r(2)) are around 0.82-0.97 for all cases). The average attenuation coefficient of rat whole blood with a hematocrit of 40% increased from 0.26 Nepers mm(-1) at 30 MHz to 0.47 Nepers mm(-1) at 60 MHz. The maximum backscattering coefficients of both rat and porcine RBC suspensions were between 10% and 15% hematocrits at all frequencies. The fourth-power dependence of backscatter on frequency was approximately valid for rat RBC suspensions with hematocrits between 6% and 40%. However, the frequency dependence of the backscatter estimate deviates from a fourth-power law for porcine RBC suspension with hematocrit higher than 20%. The backscattering coefficient plateaued for hematocrits higher than 15% in porcine blood, but for rat blood it was maximal around a hematocrit of 20% at the same rotation speed, and shifted to a hematocrit of 10% at a higher speed. The backscattering properties of rat RBCs in plasma are similar to those of RBCs in saline at a higher rotation speed. The differences in attenuation and backscattering between rat and porcine blood may be attributed to RBCs' being smaller and the RBC aggregation level being lower for rat blood than for porcine blood.

Simulation of L-band and HH microwave backscattering from coniferous forest stands - A comparison with SIR-B data

NASA Technical Reports Server (NTRS)

Sun, Guo-Qing; Simonett, David S.

1988-01-01

SIR-B images of the Mt. Shasta region of northern California are used to evaluate a composite L-band HH backscattering model of coniferous forest stands. It is found that both SIR-B and simulated backscattering coefficients for eight stands studied have similar trends and relations to average tree height and average number of trees per pixel. Also, the dispersion and distribution of simulated backscattering coefficients from each stand broadly match SIR-B data from the same stand. Although the limited quality and quantity of experimental data makes it difficult to draw any strong conclusions, the comparisons indicate that a stand-based L-band HH composite model seems promising for explaining backscattering features.

Replacing backscattering with reduced scattering. A better formulation of reflectance function?

NASA Astrophysics Data System (ADS)

Piskozub, Jacek; McKee, David; Freda, Wlodzimierz

2014-05-01

Modern reflectance formulas all involve backscattering coefficient divided by absorption coefficient (bb/a). The backscattering (or backward scattering) coefficient describes how much of the incident radiation is scattered at angles between 90 and 180 deg. However, water leaving photons are not necessarily backscattered because it is possible for a variable fraction to exit after multiple forward scattering events. Therefore the whole angular function of scattering probability (phase function) influences the reflectance signal. This is the reason why phase functions of identical backscattering ratio may result in different reflectance values, contrary to the universally used formula. This creates the question whether there may exist a better formula using a parameter better describing phase function shape than backscattering ratio. The asymmetry parameter g (the average scattering cosine) is commonly used to parametrize phase functions. A replacement for backscattering should decrease with increasing g. Therefore, the simplest candidate to replace backscattering has the form of b(1-g), where b is the scattering coefficient. Such a parameter is well known in biomedical optics under the name of reduced scattering (sometimes transport scattering). It has even been used in parametrizing reflectance in (highly turbid) human tissues. However no attempt has been made to check its usefulness in marine optics. We perform Monte Carlo radiative transfer calculations of reflectance for multiple combinations of inherent optical properties, including different phase functions. The results are used to create a new reflectance formula as a function of reduced scattering and absorption and test its robustness to changes in phase function shape compared to the traditional bb/a formula. We discuss its usefulness as well as advantages and disadvantages compared to the traditional formulation.

Recovery of singularities from a backscattering Born approximation for a biharmonic operator in 3D

NASA Astrophysics Data System (ADS)

Tyni, Teemu

2018-04-01

We consider a backscattering Born approximation for a perturbed biharmonic operator in three space dimensions. Previous results on this approach for biharmonic operator use the fact that the coefficients are real-valued to obtain the reconstruction of singularities in the coefficients. In this text we drop the assumption about real-valued coefficients and also establish the recovery of singularities for complex coefficients. The proof uses mapping properties of the Radon transform.

Feasibility of inter-comparing airborne and spaceborne obsevations of radar backscattering coefficients

USDA-ARS?s Scientific Manuscript database

The Soil Moisture Active Passive (SMAP) mission will provide global soil moisture products that will facilitate new science and application areas. The SMAP mission, scheduled for launch in November 2014, will offer synthetic aperture radar (SAR) measurements of backscattering coefficients for the re...

Multiwavelength Comparison of Modeled and Measured Remote Tropospheric Aerosol Backscatter Over Pacific Ocean

NASA Technical Reports Server (NTRS)

Cutten, D. R.; Pueschel, R. F.; Srivastava, V.; Clarke, A. D.; Rothermel, J.; Spinhirne, J. D.; Menzies, R. T.

1996-01-01

Aerosol concentrations and size distributions in the middle and upper troposphere over the remote Pacific Ocean were measured with a forward scattering spectrometer probe (FSSP) on the NASA DC-8 aircraft during NASA's Global Backscatter Experiment (GLOBE) in May-June 1990. The FSSP size channels were recalibrated based on refractive index estimates from flight-level aerosol volatility measurements with a collocated laser optical particle counter (LOPC). The recalibrated FSSP size distributions were averaged over 100-s intervals, fitted with lo-normal distributions and used to calculate aerosol backscatter coefficients at selected wavelengths. The FSSP-derived backscatter estimates were averaged over 300-s intervals to reduce large random fluctuations. The smoothed FSSP aerosol backscatter coefficients were then compared with LOPC-derived backscatter values and with backscatter measured at or near flight level from four lidar systems operating at 0.53, 1.06, 9.11, 9.25, and 10.59 micrometers. Agreement between FSSP-derived and lidar-measured backscatter was generally best at flight level in homogeneous aerosol fields and at high backscatter values. FSSP data often underestimated low backscatter values especially at the longer wavelengths due to poor counting statistics for larger particles (greater than 0.8 micrometers diameter) that usually dominate aerosol backscatter at these wavelengths. FSSP data also underestimated backscatter at shorter wavelengths when particles smaller than the FSSP lower cutoff diameter (0.35 micrometers) made significant contributions to the total backscatter.

Multi-temporal RADARSAT-1 and ERS backscattering signatures of coastal wetlands in southeastern Louisiana

USGS Publications Warehouse

Kwoun, Oh-Ig; Lu, Z.

2009-01-01

Using multi-temporal European Remote-sensing Satellites (ERS-1/-2) and Canadian Radar Satellite (RADARSAT-1) synthetic aperture radar (SAR) data over the Louisiana coastal zone, we characterize seasonal variations of radar backscat-tering according to vegetation type. Our main findings are as follows. First, ERS-1/-2 and RADARSAT-1 require careful radiometric calibration to perform multi-temporal backscattering analysis for wetland mapping. We use SAR backscattering signals from cities for the relative calibration. Second, using seasonally averaged backscattering coefficients from ERS-1/-2 and RADARSAT-1, we can differentiate most forests (bottomland and swamp forests) and marshes (freshwater, intermediate, brackish, and saline marshes) in coastal wetlands. The student t-test results support the usefulness of season-averaged backscatter data for classification. Third, combining SAR backscattering coefficients and an optical-sensor-based normalized difference vegetation index can provide further insight into vegetation type and enhance the separation between forests and marshes. Our study demonstrates that SAR can provide necessary information to characterize coastal wetlands and monitor their changes.

Determination of the particulate extinction-coefficient profile and the column-integrated lidar ratios using the backscatter-coefficient and optical-depth profiles

Treesearch

Vladimir A Kovalev; Wei Min Hao; Cyle Wold

2007-01-01

A new method is considered that can be used for inverting data obtained from a combined elastic-inelastic lidar or a high spectral resolution lidar operating in a one-directional mode, or an elastic lidar operating in a multiangle mode. The particulate extinction coefficient is retrieved from the simultaneously measured profiles of the particulate backscatter...

Beta systems error analysis

NASA Technical Reports Server (NTRS)

1984-01-01

The atmospheric backscatter coefficient, beta, measured with an airborne CO Laser Doppler Velocimeter (LDV) system operating in a continuous wave, focussed model is discussed. The Single Particle Mode (SPM) algorithm, was developed from concept through analysis of an extensive amount of data obtained with the system on board a NASA aircraft. The SPM algorithm is intended to be employed in situations where one particle at a time appears in the sensitive volume of the LDV. In addition to giving the backscatter coefficient, the SPM algorithm also produces as intermediate results the aerosol density and the aerosol backscatter cross section distribution. A second method, which measures only the atmospheric backscatter coefficient, is called the Volume Mode (VM) and was simultaneously employed. The results of these two methods differed by slightly less than an order of magnitude. The measurement uncertainties or other errors in the results of the two methods are examined.

Observations of Radar Backscatter at Ku and C Bands in the Presence of Large Waves during the Surface Wave Dynamics Experiment

NASA Technical Reports Server (NTRS)

Nghiem, S. V.; Li, Fuk K.; Lou, Shu-Hsiang; Neumann, Gregory; McIntosh, Robert E.; Carson, Steven C.; Carswell, James R.; Walsh, Edward J.; Donelan, Mark A.; Drennan, William M.

1995-01-01

Ocean radar backscatter in the presence of large waves is investigated using data acquired with the Jet Propulsion Laboratory NUSCAT radar at Ku band for horizontal and vertical polarizations and the University of Massachusetts CSCAT radar at C band for vertical polarization during the Surface Wave Dynamics Experiment. Off-nadir backscatter data of ocean surfaces were obtained in the presence of large waves with significant wave height up to 5.6 m. In moderate-wind cases, effects of large waves are not detectable within the measurement uncertainty and no noticeable correlation between backscatter coefficients and wave height is found. Under high-wave light-wind conditions, backscatter is enhanced significantly at large incidence angles with a weaker effect at small incidence angles. Backscatter coefficients in the wind speed range under consideration are compared with SASS-2 (Ku band), CMOD3-H1 (C band), and Plant's model results which confirm the experimental observations. Variations of the friction velocity, which can give rise to the observed backscatter behaviors in the presence of large waves, are presented.

Relating multifrequency radar backscattering to forest biomass: Modeling and AIRSAR measurement

NASA Technical Reports Server (NTRS)

Sun, Guo-Qing; Ranson, K. Jon

1992-01-01

During the last several years, significant efforts in microwave remote sensing were devoted to relating forest parameters to radar backscattering coefficients. These and other studies showed that in most cases, the longer wavelength (i.e. P band) and cross-polarization (HV) backscattering had higher sensitivity and better correlation to forest biomass. This research examines this relationship in a northern forest area through both backscatter modeling and synthetic aperture radar (SAR) data analysis. The field measurements were used to estimate stand biomass from forest weight tables. The backscatter model described by Sun et al. was modified to simulate the backscattering coefficients with respect to stand biomass. The average number of trees per square meter or radar resolution cell, and the average tree height or diameter breast height (dbh) in the forest stand are the driving parameters of the model. The rest of the soil surface, orientation, and size distributions of leaves and branches, remain unchanged in the simulations.

Quantitative Analysis of Venus Radar Backscatter Data in ArcGIS

NASA Technical Reports Server (NTRS)

Long, S. M.; Grosfils, E. B.

2005-01-01

Ongoing mapping of the Ganiki Planitia (V14) quadrangle of Venus and definition of material units has involved an integrated but qualitative analysis of Magellan radar backscatter images and topography using standard geomorphological mapping techniques. However, such analyses do not take full advantage of the quantitative information contained within the images. Analysis of the backscatter coefficient allows a much more rigorous statistical comparison between mapped units, permitting first order selfsimilarity tests of geographically separated materials assigned identical geomorphological labels. Such analyses cannot be performed directly on pixel (DN) values from Magellan backscatter images, because the pixels are scaled to the Muhleman law for radar echoes on Venus and are not corrected for latitudinal variations in incidence angle. Therefore, DN values must be converted based on pixel latitude back to their backscatter coefficient values before accurate statistical analysis can occur. Here we present a method for performing the conversions and analysis of Magellan backscatter data using commonly available ArcGIS software and illustrate the advantages of the process for geological mapping.

The effect of leaf size on the microwave backscattering by corn

NASA Technical Reports Server (NTRS)

Paris, J. F.

1986-01-01

Attema and Ulaby (1978) proposed the cloud model to predict the microwave backscattering properties of vegetation. This paper describes a modification in which the biophysical properties and microwave properties of vegetation are related at the level of the individual scatterer (e.g., the leaf or the stalk) rather than at the level of the aggregated canopy (e.g., the green leaf area index). Assuming that the extinction cross section of an average leaf was proportional to its water content, that a power law relationship existed between the backscattering cross section of an average green corn leaf and its area, and that the backscattering coefficient of the surface was a linear function of its volumetric soil moisture content, it is found that the explicit inclusion of the effects of corn leaf size in the model led to an excellent fit between the observed and predicted backscattering coefficients. Also, an excellent power law relationship existed between the backscattering cross section of a corn leaf and its area.

In-cell measurements of smoke backscattering coefficients using a CO2 laser system for application to lidar-dial forest fire detection

NASA Astrophysics Data System (ADS)

Bellecci, Carlo; Gaudio, Pasquale; Gelfusa, Michela; Lo Feudo, Teresa; Murari, Andrea; Richetta, Maria; de Leo, Leonerdo

2010-12-01

In the lidar-dial method, the amount of the water vapor present in the smoke of the vegetable fuel is detected to reduce the number of false alarms. We report the measurements of the smoke backscattering coefficients for the CO2 laser lines 10R20 and 10R18 as determined in an absorption cell for two different vegetable fuels (eucalyptus and conifer). These experimental backscattering coefficients enable us to determine the error to be associated to the water vapor measurements when the traditional first-order approximation is assumed. We find that this first-order approximation is valid for combustion rates as low as 100 g/s.

Remotely sensing wheat maturation with radar

NASA Technical Reports Server (NTRS)

Bush, T. F.; Ulaby, F. T.

1975-01-01

The scattering properties of wheat were studied in the 8-18 GHz band as a function of frequency, polarization, incidence angle, and crop maturity. Supporting ground truth was collected at the time of measurement. The data indicate that the radar backscattering coefficient is sensitive to both radar system parameters and crop characteristics particularly at incidence angles near nadir. Linear regression analyses of the radar backscattering coefficient on both time and plant moisture content result in rather good correlation. Furthermore, by calculating the average time rate of change of the radar backscattering coefficient it is found that it undergoes rapid variations shortly before and after the wheat is harvested. Both of these analyses suggest methods for estimating wheat maturity and for monitoring the progress of harvest.

Comparison of radar backscatter from Antarctic and Arctic sea ice

NASA Technical Reports Server (NTRS)

Hosseinmostafa, R.; Lytle, V.

1992-01-01

Two ship-based step-frequency radars, one at C-band (5.3 GHz) and one at Ku-band (13.9 GHz), measured backscatter from ice in the Weddell Sea. Most of the backscatter data were from first-year (FY) and second-year (SY) ice at the ice stations where the ship was stationary and detailed snow and ice characterizations were performed. The presence of a slush layer at the snow-ice interface masks the distinction between FY and SY ice in the Weddell Sea, whereas in the Arctic the separation is quite distinct. The effect of snow-covered ice on backscattering coefficients (sigma0) from the Weddell Sea region indicates that surface scattering is the dominant factor. Measured sigma0 values were compared with Kirchhoff and regression-analysis models. The Weibull power-density function was used to fit the measured backscattering coefficients at 45 deg.

Measuring Ultrasonic Backscatter in the Presence of Nonlinear Propagation

NASA Astrophysics Data System (ADS)

Stiles, Timothy; Guerrero, Quinton

2011-11-01

A goal of medical ultrasound is the formation of quantitative ultrasound images in which contrast is determined by acoustic or physical properties of tissue rather than relative echo amplitude. Such images could greatly enhance early detection of many diseases, including breast cancer and liver cirrhosis. Accurate determination of the ultrasonic backscatter coefficient from patients remains a difficult task. One reason for this difficulty is the inherent nonlinear propagation of ultrasound at high intensities used for medical imaging. The backscatter coefficient from several tissue-mimicking samples were measured using the planar reflector method. In this method, the power spectrum from a sample is compared to the power spectrum of an optically flat sample of quartz. The results should be independent of incident pressure amplitude. Results demonstrate that backscatter coefficients can vary by more than an order of magnitude when ultrasound pressure varies from 0.1 MPa to 1.5 MPa at 5.0 MHz. A new method that incorporates nonlinear propagation is proposed to explain these discrepancies.

International Laser Radar Conference (16th) held at the Massachusetts Institute of Technology, Cambridge, Massachusetts on 20-24 July 1992. Part 1

DTIC Science & Technology

1993-07-24

orders smaller than the Rayleigh cross section. We estimated the extinction coefficients of the Pinatubo volcanic aerosol in the stratosphere using a Raman...to a common aerosol parameter (e.g., backscatter coefficients at selected CO2 wavelengths), have all led to similar estimated values of that...increase only as -r 2 . During this phase, therefore, the backscatter coefficient of a coagulating aerosol population decreases as -r- The maximum

Lidar extinction measurement in the mid infrared

NASA Astrophysics Data System (ADS)

Mitev, Valentin; Babichenko, S.; Borelli, R.; Fiorani, L.; Grigorov, I.; Nuvoli, M.; Palucci, A.; Pistilli, M.; Puiu, Ad.; Rebane, Ott; Santoro, S.

2014-11-01

We present a lidar measurement of atmospheric extinction coefficient. The measurement is performed by inversion of the backscatter lidar signal at wavelengths 3'000nm and 3'500nm. The inversion of the backscatter lidar signal was performed with constant extinction-to-backscatter ration values of 104 and exponential factor 0.1.

Identification of transplanting stage of rice using Sentinel-1 data

NASA Astrophysics Data System (ADS)

Hongo, C.; Tosa, T.; Tamura, E.; Sigit, G.; Barus, B.

2017-12-01

As the adaptation of climate change, the Government of Indonesia has launched agricultural insurance program for damage of rice by drought, flood and pest and disease. For assessment of the damage ratio and calculation of indemnity, extraction of paddy field and identification of transplanting stage are key issues. In this research, we conducted identification of rice transplanting stage in dry season of 2015, using data from Sentinel-1, for paddy in Cianjur, West Java, Indonesia. As the first step, time series order of backscattering coefficient was analyzed about paddy, forest, villages and fish farming ponds with use of Sentinel-1 data acquired on April 1, April 13, April 25, May 7, May 19, June 24, July 18 and August 11. The result shows that the backscattering coefficient of paddy substantially decreased from data on May 7 and reached minimum value and then after increased toward June. A paddy area showing this change was almost the same area where rice was at harvesting stage and we did field investigation work from August 11 to 13. Considering a growth period of rice in our research site was about 110 days, so the result supported the fact that transplantation of rice was done around May 7. On the other hand, backscattering coefficient of forest, villages and fish farming ponds was constant and showed clear difference from the coefficient of paddy. As the next step, minimum and maximum value of backscattering coefficient were extracted from the data of May 7, May 19 and June 24, respectively. Then increase amount was calculated by deducting the minimum value from the maximum. Finally, using the minimum value of backscattering coefficient and the increased amount, a classification of image was made to identify transplanting stage through maximum likelihood method, decision tree method and threshold setting method (regression analysis by 3σ-rule). As the result, the maximum likelihood method made the most accurate distinguishment about transplanting stage while the decision tree method showed tendency to underestimate a paddy area already planted. As to the threshold setting method (regression analysis by 3σ-rule), its distinguishment accuracy was better than those of other methods about a paddy area adjacent to forest and villages of which backscattering coefficient was influenced by other sources' coefficients.

Modeling of microwave scattering from vegetated covered terrain

NASA Technical Reports Server (NTRS)

Lang, R. H.

1982-01-01

General formulation of resonant backscattering from vegetation, mean field and Green's function in three media, and electromagnetic backscattering coefficients from a layer of vegetation are discussed.

Backscattering and vegetation water content response of paddy crop at C-band using RISAT-1 satellite data

NASA Astrophysics Data System (ADS)

Kumar, Pradeep; Prasad, Rajendra; Choudhary, Arti; Gupta, Dileep Kumar; Narayan Mishra, Varun; Srivastava, Prashant K.

2016-04-01

The study about the temporal behaviour of vegetation water content (VWC) is essential for monitoring the growth of a crop to improve agricultural production. In agriculture, VWC could possibly provide information that can be used to infer water stress for irrigation decisions, vegetation health conditions, aid in yield estimation and assessment of drought conditions (Penuelas et al., 1993). The VWC is an important parameter for soil moisture retrieval in microwave remote sensing (Srivastava et al., 2014). In the present study, the backscattering and VWC response of paddy crop has been investigated using medium resolution (MRS) radar imaging satellite-1 (RISAT-1) synthetic aperture radar (SAR) data in Varanasi, India. The VWC of paddy crop was measured at its five different growth stages started from 15 July 2013 to 23 October 2013 from the transplanting to maturity stage during Kharif season. The whole life of paddy crop was divided into three different major growth stages like vegetative stage, reproductive stage and ripening stage. During vegetative stage, the backscattering coefficients were found increasing behaviour until the leaves became large and dense due to major contribution of stems and the interaction between the stems and water underneath the paddy crop. During reproductive stage, the backscattering coefficients were found to increase slowly due to random scattering by vertical leaves. The increase in the size of leaves cause to cover most of the spaces between plants resulted to quench the contributions from the stems and the water underneath. At the maturity stage, the backscattering showed its decreasing behaviour. The VWC of paddy crop was found increasing up to vegetative to reproductive stages (28 September 2013) and then started decreasing during the ripening (maturity) stage. Similar behaviour was obtained between backscattering coefficients and VWC that showed an increasing trend from vegetative to reproductive stage and then lowering down at ripening stage at HH- and HV- polarizations. It is concluded that HH- polarized backscattering coefficients using RISAT-1 data are more sensitive in comparison to HV- polarized backscattering coefficients. The C-band, RISAT-1 backscattering coefficients may be useful for the retrieval of VWC of paddy crop to monitor its growth stages. Keywords: SAR, C-band, dual polarimetric, RISAT-1, VWC, paddy References: Penuelas, J., Filella, I., Biel, C., Serrano, L., & Save, R. (1993). The reflectance at the 950-970 mm region as an indicator of plant water status. International Journal of Remote Sensing, 14:1887-1905. Srivastava , P. K., Han, D., Rico-Ramirez, M. A., O'Neill, P., Islam, T., & Gupta, M. (2014). Assessment of SMOS soil moisture retrieval parameters using tau-omega algorithms for soil moisture deficit estimation. Journal of Hydrology 519:574-587

OPTOELECTRONICS, FIBER OPTICS, AND OTHER ASPECTS OF QUANTUM ELECTRONICS: Influence of the Rayleigh backscattering on the mode composition of radiation in multimode graded-index waveguides with a quadratic refractive-index profile

NASA Astrophysics Data System (ADS)

Esayan, G. L.; Krivoshlykov, S. G.

1989-08-01

A method of coherent states is used to describe the process of Rayleigh scattering in a multimode graded-index waveguide with a quadratic refractive-index profile. Explicit expressions are obtained for the coefficients representing excitation of Gaussian-Hermite backscattering modes in two cases of practical importance: excitation of a waveguide by an extended noncoherent light source and selective excitation of different modes at the entry to a waveguide. An analysis is also made of the coefficients of coupling between forward and backward modes. Explicit expressions for the coefficients representing capture of backscattered radiation by a waveguide are obtained for two special cases of excitation (extended light source and zeroth mode).

Retrieval method of aerosol extinction coefficient profile by an integral lidar system and case study

NASA Astrophysics Data System (ADS)

Shan, Huihui; Zhang, Hui; Liu, Junjian; Wang, Shenhao; Ma, Xiaomin; Zhang, Lianqing; Liu, Dong; Xie, Chenbo; Tao, Zongming

2018-02-01

Aerosol extinction coefficient profile is an essential parameter for atmospheric radiation model. But it is difficult to get the full aerosol extinction profile from the ground to the tropopause especially in near ground precisely using backscattering lidar. A combined measurement of side-scattering, backscattering and Raman-scattering lidar is proposed to retrieve the aerosol extinction coefficient profile from the surface to the tropopause which covered a dynamic range of 5 orders. The side-scattering technique solves the dead zone and the overlap problem caused by the traditional lidar in the near range. Using the Raman-scattering the aerosol lidar ratio (extinction to backscatter ratio) can be obtained. The cases studies in this paper show the proposed method is reasonable and feasible.

Light scattering and backscattering by particles suspended in the Baltic Sea in relation to the mass concentration of particles and the proportions of their organic and inorganic fractions

NASA Astrophysics Data System (ADS)

Woźniak, Sławomir B.; Sagan, Sławomir; Zabłocka, Monika; Stoń-Egiert, Joanna; Borzycka, Karolina

2018-06-01

The empirical relationships were examined of spectral characteristics of light scattering and backscattering by particles suspended in seawater in relation to the dry mass concentration of particles and the bulk proportions of their organic and inorganic fractions. The analyses were based on empirical data collected in the surface waters of the southern and central Baltic Sea at different times of the year. It was found that the average scattering and backscattering coefficients, normalized to the dry mass concentration of particles for all our Baltic Sea data (i.e. mass-specific optical coefficients), were characterized by large coefficients of variation (CV) of the order of 30% at all the visible light wavelengths analysed. At wavelength 555 nm the average mass-specific scattering coefficient was ca 0.75 m2 g- 1 (CV = 31%); the corresponding value for backscattering was 0.0072 m2 g- 1 (CV = 29%). The analyses confirmed that some of the observed variations could be explained by changes in the proportions of organic and inorganic fractions of suspended matter. The average organic fraction in all the samples was as high as 83% of the total dry mass concentration but in individual cases it varied between < 50% and up to 100%. Simple, two-variable parameterizations of scattering and backscattering coefficients were derived as functions of the organic and inorganic fraction concentrations. The statistical relationship between the backscattering ratio and the ratio of the organic fraction to the total dry mass of suspended matter was also found: this can be used in practical interpretations of in situ optical measurements. In addition, the variability in particle size distributions recorded with a Coulter counter indicated its potentially highly significant influence on the light scattering properties of particles suspended in Baltic Sea waters.

Characterizing tissue microstructure using an ultrasound system-independent spatial autocorrelation function

NASA Astrophysics Data System (ADS)

Dong, Fang

1999-09-01

The research described in this dissertation is related to characterization of tissue microstructure using a system- independent spatial autocorrelation function (SAF). The function was determined using a reference phantom method, which employed a well-defined ``point- scatterer'' reference phantom to account for instrumental factors. The SAF's were estimated for several tissue-mimicking (TM) phantoms and fresh dog livers. Both phantom tests and in vitro dog liver measurements showed that the reference phantom method is relatively simple and fairly accurate, providing the bandwidth of the measurement system is sufficient for the size of the scatterer being involved in the scattering process. Implementation of this method in clinical scanner requires that distortions from patient's body wall be properly accounted for. The SAF's were estimated for two phantoms with body-wall-like distortions. The experimental results demonstrated that body wall distortions have little effect if echo data are acquired from a large scattering volume. One interesting application of the SAF is to form a ``scatterer size image''. The scatterer size image may help providing diagnostic tools for those diseases in which the tissue microstructure is different from the normal. Another method, the BSC method, utilizes information contained in the frequency dependence of the backscatter coefficient to estimate the scatterer size. The SAF technique produced accurate scatterer size images of homogeneous TM phantoms and the BSC method was capable of generating accurate size images for heterogeneous phantoms. In the scatterer size image of dog kidneys, the contrast-to-noise-ratio (CNR) between renal cortex and medulla was improved dramatically compared to the gray- scale image. The effect of nonlinear propagation was investigated by using a custom-designed phantom with overlaying TM fat layer. The results showed that the correlation length decreased when the transmitting power increased. The measurement results support the assumption that nonlinear propagation generates harmonic energies and causes underestimation of scatterer diameters. Nonlinear propagation can be further enhanced by those materials with high B/A value-a parameter which characterizes the degree of nonlinearity. Nine versions of TM fat and non-fat materials were measured for their B/A values using a new measurement technique, the ``simplified finite amplitude insertion substitution'' (SFAIS) method.

The SIR-B observations of microwave backscatter dependence on soil moisture, surface roughness, and vegetation covers

NASA Technical Reports Server (NTRS)

Wang, J. R.; Shiue, J. C.; Engman, E. T.; Rusek, M.; Steinmeier, C.

1986-01-01

An experiment was conducted from an L-band SAR aboard Space Shuttle Challenger in October 1984 to study the microwave backscatter dependence on soil moisture, surface roughness, and vegetation cover. The results based on the analyses of an image obtained at 21-deg incidence angle show a positive correlatlion between scattering coefficient and soil moisture content, with a sensitivity comparable to that derived from the ground radar measurements reported by Ulaby et al. (1978). The surface roughness strongly affects the microwave backscatter. A factor of two change in the standard deviation of surface roughness height gives a corresponding change of about 8 dB in the scattering coefficient. The microwave backscatter also depends on the vegetation types. Under the dry soil conditions, the scattering coefficient is observed to change from about -24 dB for an alfalfa or lettuce field to about -17 dB for a mature corn field. These results suggest that observations with a SAR system of multiple frequencies and polarizations are required to unravel the effects of soil moisture, surface roughness, and vegetation cover.

CALIOP near-real-time backscatter products compared to EARLINET data

NASA Astrophysics Data System (ADS)

Grigas, T.; Hervo, M.; Gimmestad, G.; Forrister, H.; Schneider, P.; Preißler, J.; Tarrason, L.; O'Dowd, C.

2015-03-01

The expedited near-real-time Level 1.5 Cloud-Aerosol Lidar (Light Detection and Ranging) with Orthogonal Polarization (CALIOP) products were evaluated against data from the ground-based European Aerosol Research Lidar Network (EARLINET). Over a period of three years, lidar data from 48 CALIOP overpasses with ground tracks within a 100 km distance from an operating EARLINET station were deemed suitable for analysis and they included a valid aerosol classification type (e.g. dust, polluted dust, clean marine, clean continental, polluted continental, mixed and/or smoke/biomass burning). For the complete dataset comprising both PBL and FT data, the correlation coefficient was 0.86, and when separated into separate layers, the PBL and FT correlation coefficients were 0.6 and 0.85 respectively. The presence of FT layers with high attenuated backscatter led to poor agreement in PBL backscatter profiles between the CALIOP and EARLINET measurements and prompted a further analysis filtering out such cases. However, the correlation coefficient value for the complete dataset decreased marginally from 0.86 to 0.84 while the PBL coefficient increased from 0.6 up to 0.65 and the FT coefficient also decreased from 0.85 to 0.79. For specific aerosol types, the correlation coefficient between CALIOP backscatter profiles and ground-based lidar data ranged from 0.37 for polluted continental aerosol in the planetary boundary layer (PBL) to 0.57 for dust in the free troposphere (FT). The results suggest different levels of agreement based on the location of the dominant aerosol layer and the aerosol type.

Remote sensing of PM2.5 from ground-based optical measurements

NASA Astrophysics Data System (ADS)

Li, S.; Joseph, E.; Min, Q.

2014-12-01

Remote sensing of particulate matter concentration with aerodynamic diameter smaller than 2.5 um(PM2.5) by using ground-based optical measurements of aerosols is investigated based on 6 years of hourly average measurements of aerosol optical properties, PM2.5, ceilometer backscatter coefficients and meteorological factors from Howard University Beltsville Campus facility (HUBC). The accuracy of quantitative retrieval of PM2.5 using aerosol optical depth (AOD) is limited due to changes in aerosol size distribution and vertical distribution. In this study, ceilometer backscatter coefficients are used to provide vertical information of aerosol. It is found that the PM2.5-AOD ratio can vary largely for different aerosol vertical distributions. The ratio is also sensitive to mode parameters of bimodal lognormal aerosol size distribution when the geometric mean radius for the fine mode is small. Using two Angstrom exponents calculated at three wavelengths of 415, 500, 860nm are found better representing aerosol size distributions than only using one Angstrom exponent. A regression model is proposed to assess the impacts of different factors on the retrieval of PM2.5. Compared to a simple linear regression model, the new model combining AOD and ceilometer backscatter can prominently improve the fitting of PM2.5. The contribution of further introducing Angstrom coefficients is apparent. Using combined measurements of AOD, ceilometer backscatter, Angstrom coefficients and meteorological parameters in the regression model can get a correlation coefficient of 0.79 between fitted and expected PM2.5.

Effects of vegetation canopy on the radar backscattering coefficient

NASA Technical Reports Server (NTRS)

Mo, T.; Blanchard, B. J.; Schmugge, T. J.

1983-01-01

Airborne L- and C-band scatterometer data, taken over both vegetation-covered and bare fields, were systematically analyzed and theoretically reproduced, using a recently developed model for calculating radar backscattering coefficients of rough soil surfaces. The results show that the model can reproduce the observed angular variations of radar backscattering coefficient quite well via a least-squares fit method. Best fits to the data provide estimates of the statistical properties of the surface roughness, which is characterized by two parameters: the standard deviation of surface height, and the surface correlation length. In addition, the processes of vegetation attenuation and volume scattering require two canopy parameters, the canopy optical thickness and a volume scattering factor. Canopy parameter values for individual vegetation types, including alfalfa, milo and corn, were also determined from the best-fit results. The uncertainties in the scatterometer data were also explored.

Spectra of Particulate Backscattering in Natural Waters

NASA Technical Reports Server (NTRS)

Gordon, Howard, R.; Lewis, Marlon R.; McLean, Scott D.; Twardowski, Michael S.; Freeman, Scott A.; Voss, Kenneth J.; Boynton, Chris G.

2009-01-01

Hyperspectral profiles of downwelling irradiance and upwelling radiance in natural waters (oligotrophic and mesotrophic) are combined with inverse radiative transfer to obtain high resolution spectra of the absorption coefficient (a) and the backscattering coefficient (bb) of the water and its constituents. The absorption coefficient at the mesotrophic station clearly shows spectral absorption features attributable to several phytoplankton pigments (Chlorophyll a, b, c, and Carotenoids). The backscattering shows only weak spectral features and can be well represented by a power-law variation with wavelength (lambda): b(sub b) approx. Lambda(sup -n), where n is a constant between 0.4 and 1.0. However, the weak spectral features in b(sub b), suggest that it is depressed in spectral regions of strong particle absorption. The applicability of the present inverse radiative transfer algorithm, which omits the influence of Raman scattering, is limited to lambda < 490 nm in oligotrophic waters and lambda < 575 nm in mesotrophic waters.

Monitoring Everglades freshwater marsh water level using L-band synthetic aperture radar backscatter

USGS Publications Warehouse

Kim, Jin-Woo; Lu, Zhong; Jones, John W.; Shum, C.K.; Lee, Hyongki; Jia, Yuanyuan

2014-01-01

The Florida Everglades plays a significant role in controlling floods, improving water quality, supporting ecosystems, and maintaining biodiversity in south Florida. Adaptive restoration and management of the Everglades requires the best information possible regarding wetland hydrology. We developed a new and innovative approach to quantify spatial and temporal variations in wetland water levels within the Everglades, Florida. We observed high correlations between water level measured at in situ gages and L-band SAR backscatter coefficients in the freshwater marsh, though C-band SAR backscatter has no close relationship with water level. Here we illustrate the complementarity of SAR backscatter coefficient differencing and interferometry (InSAR) for improved estimation of high spatial resolution water level variations in the Everglades. This technique has a certain limitation in applying to swamp forests with dense vegetation cover, but we conclude that this new method is promising in future applications to wetland hydrology research.

New Examination of the Traditional Raman Lidar Technique II: Evaluating the Ratios for Water Vapor and Aerosols

NASA Technical Reports Server (NTRS)

Whiteman, David N.

2003-01-01

In a companion paper, the temperature dependence of Raman scattering and its influence on the Raman and Rayleigh-Mie lidar equations was examined. New forms of the lidar equation were developed to account for this temperature sensitivity. Here those results are used to derive the temperature dependent forms of the equations for the water vapor mixing ratio, aerosol scattering ratio, aerosol backscatter coefficient, and extinction to backscatter ratio (Sa). The error equations are developed, the influence of differential transmission is studied and different laser sources are considered in the analysis. The results indicate that the temperature functions become significant when using narrowband detection. Errors of 5% and more can be introduced in the water vapor mixing ratio calculation at high altitudes and errors larger than 10% are possible for calculations of aerosol scattering ratio and thus aerosol backscatter coefficient and extinction to backscatter ratio.

Effects of soil and canopy characteristics on microwave backscattering of vegetation

NASA Technical Reports Server (NTRS)

Daughtry, C. S. T.; Ranson, K. J.

1991-01-01

A frequency modulated continuous wave C-band (4.8 GHz) scatterometer was mounted on an aerial lift truck and backscatter coefficients of corn were acquired as functions of polarizations, view angles, and row directions. As phytomass and green leaf area index increased, the backscatter also increased. Near anthesis when the canopies were fully developed, the major scattering elements were located in the upper 1 m of the 2.8 m tall canopy and little backscatter was measured below that level. C-band backscatter data could provide information to monitor vegetation at large view zenith angles.

Backscattering and absorption coefficients for electrons: Solutions of invariant embedding transport equations using a method of convergence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Figueroa, C.; Brizuela, H.; Heluani, S. P.

2014-05-21

The backscattering coefficient is a magnitude whose measurement is fundamental for the characterization of materials with techniques that make use of particle beams and particularly when performing microanalysis. In this work, we report the results of an analytic method to calculate the backscattering and absorption coefficients of electrons in similar conditions to those of electron probe microanalysis. Starting on a five level states ladder model in 3D, we deduced a set of integro-differential coupled equations of the coefficients with a method know as invariant embedding. By means of a procedure proposed by authors, called method of convergence, two types ofmore » approximate solutions for the set of equations, namely complete and simple solutions, can be obtained. Although the simple solutions were initially proposed as auxiliary forms to solve higher rank equations, they turned out to be also useful for the estimation of the aforementioned coefficients. In previous reports, we have presented results obtained with the complete solutions. In this paper, we present results obtained with the simple solutions of the coefficients, which exhibit a good degree of fit with the experimental data. Both the model and the calculation method presented here can be generalized to other techniques that make use of different sorts of particle beams.« less

Effects of changing environmental conditions on synthetic aperture radar backscattering coefficient, scattering mechanisms, and class separability in a forest area

NASA Astrophysics Data System (ADS)

Mahdavi, Sahel; Maghsoudi, Yasser; Amani, Meisam

2017-07-01

Environmental conditions have considerable effects on synthetic aperture radar (SAR) imagery. Therefore, assessing these effects is important for obtaining accurate and reliable results. In this study, three series of RADARSAT-2 SAR images were evaluated. In each of these series, the sensor configuration was fixed, but the environmental conditions differed. The effects of variable environmental conditions were also investigated on co- and cross-polarized backscattering coefficients, Freeman-Durden scattering contributions, and the pedestal height in different classes of a forest area in Ottawa, Ontario. It was observed that the backscattering coefficient of wet snow was up to 2 dB more than that of dry snow. The absence of snow also caused a decrease of up to 3 dB in the surface scattering of ground and up to 5 dB in that of trees. In addition, the backscatter coefficients of ground vegetation, hardwood species, and softwood species were more similar at temperatures below 0°C than those at temperatures above 0°C. Moreover, the pedestal height was generally greater at temperatures above 0°C than at temperatures below 0°C. Finally, the highest class separability was observed when the temperature was at or above 0°C and there was no snow on the ground or trees.

Absolute backscatter coefficient estimates of tissue-mimicking phantoms in the 5–50 MHz frequency range

PubMed Central

McCormick, Matthew M.; Madsen, Ernest L.; Deaner, Meagan E.; Varghese, Tomy

2011-01-01

Absolute backscatter coefficients in tissue-mimicking phantoms were experimentally determined in the 5–50 MHz frequency range using a broadband technique. A focused broadband transducer from a commercial research system, the VisualSonics Vevo 770, was used with two tissue-mimicking phantoms. The phantoms differed regarding the thin layers covering their surfaces to prevent desiccation and regarding glass bead concentrations and diameter distributions. Ultrasound scanning of these phantoms was performed through the thin layer. To avoid signal saturation, the power spectra obtained from the backscattered radio frequency signals were calibrated by using the signal from a liquid planar reflector, a water-brominated hydrocarbon interface with acoustic impedance close to that of water. Experimental values of absolute backscatter coefficients were compared with those predicted by the Faran scattering model over the frequency range 5–50 MHz. The mean percent difference and standard deviation was 54% ± 45% for the phantom with a mean glass bead diameter of 5.40 μm and was 47% ± 28% for the phantom with 5.16 μm mean diameter beads. PMID:21877789

Vertically-resolved profiles of mass concentrations and particle backscatter coefficients of Asian dust plumes derived from lidar observations of silicon dioxide.

PubMed

Noh, Youngmin; Müller, Detlef; Shin, Sung-Kyun; Shin, Dongho; Kim, Young J

2016-01-01

This study presents a method to retrieve vertically-resolved profiles of dust mass concentrations by analyzing Raman lidar signals of silicon dioxide (quartz) at 546nm. The observed particle plumes consisted of mixtures of East Asian dust with anthropogenic pollution. Our method for the first time allows for extracting the contribution of the aerosol component "pure dust" contained in the aerosol type "polluted dust". We also propose a method that uses OPAC (Optical Properties of Aerosols and Clouds) and the mass concentrations profiles of dust in order to derive profiles of backscatter coefficients of pure dust in mixed dust/pollution plumes. The mass concentration of silicon dioxide (quartz) in the atmosphere can be estimated from the backscatter coefficient of quartz. The mass concentration of dust is estimated by the weight percentage (38-77%) of mineral quartz in Asian dust. The retrieved dust mass concentrations are classified into water soluble, nucleation, accumulation, mineral-transported and coarse mode according to OPAC. The mass mixing ratio of 0.018, 0.033, 0.747, 0.130 and 0.072, respectively, is used. Dust extinction coefficients at 550nm were calculated by using OPAC and prescribed number concentrations for each of the 5 components. Dust backscatter coefficients were calculated from the dust extinction coefficients on the basis of a lidar ratio of 45±3sr at 532nm. We present results of quartz-Raman measurements carried out on the campus of the Gwangju Institute of Science and Technology (35.10°N, 126.53°E) on 15, 16, and 21 March 2010. Copyright © 2015 Elsevier Ltd. All rights reserved.

Measurement of tropospheric aerosol in São Paulo area using a new upgraded Raman LIDAR system

NASA Astrophysics Data System (ADS)

Landulfo, Eduardo; Rodrigues, Patrícia F.; da Silva Lopes, Fábio Juliano; Bourayou, Riad

2012-11-01

Elastic backscatter LIDAR systems have been used to determine aerosol profile concentration in several areas such as weather, pollution and air quality monitoring. In order to determine the aerosol extinction and backscattering profiles, the Klett inversion method is largely used, but this method suffers from lack of information since there are two unknown variables to be determined using only one measured LIDAR signal, and assumption of the LIDAR ratio (the relation between the extinction and backscattering coefficients) is needed. When a Raman LIDAR system is used, the inelastic backscattering signal is affected by aerosol extinction but not by aerosol backscatter, which allows this LIDAR to uniquely determine extinction and backscattering coefficients without any assumptions or any collocated instruments. The MSP-LIDAR system, set-up in a highly dense suburban area in the city of São Paulo, has been upgraded to a Raman LIDAR, and in its actual 6-channel configuration allows it to monitor elastic backscatter at 355 and 532 nm together with nitrogen and water vapor Raman backscatters at 387nm and 608 nm and 408nm and 660 nm, respectively. Thus, the measurements of aerosol backscattering, extinction coefficients and water vapor mixing ratio in the Planetary Boundary Layer (PBL) are becoming available. The system will provide the important meteorological parameters such as Aerosol Optical Depth (AOD) and will be used for the study of aerosol variations in lower troposphere over the city of São Paulo, air quality monitoring and for estimation of humidity impact on the aerosol optical properties, without any a priori assumption. This study will present the first results obtained with this upgraded LIDAR system, demonstrating the high quality of obtained aerosol and water vapor data. For that purpose, we compared the data obtained with the new MSP-Raman LIDAR with a mobile Raman LIDAR collocated at the Center for Lasers and Applications, Nuclear and Energy Research Institute in São Paulo and radiosonde data from Campo de Marte Airport, in São Paulo.

Backscattering from a randomly rough dielectric surface

NASA Technical Reports Server (NTRS)

Fung, Adrian K.; Li, Zongqian; Chen, K. S.

1992-01-01

A backscattering model for scattering from a randomly rough dielectric surface is developed based on an approximate solution of a pair of integral equations for the tangential surface fields. Both like and cross-polarized scattering coefficients are obtained. It is found that the like polarized scattering coefficients contain two types of terms: single scattering terms and multiple scattering terms. The single scattering terms in like polarized scattering are shown to reduce the first-order solutions derived from the small perturbation method when the roughness parameters satisfy the slightly rough conditions. When surface roughnesses are large but the surface slope is small, only a single scattering term corresponding to the standard Kirchhoff model is significant. If the surface slope is large, the multiple scattering term will also be significant. The cross-polarized backscattering coefficients satisfy reciprocity and contain only multiple scattering terms. The difference between vertical and horizontal scattering coefficients is found to increase with the dielectric constant and is generally smaller than that predicted by the first-order small perturbation model. Good agreements are obtained between this model and measurements from statistically known surfaces.

Validation Test Report for the BioCast Optical Forecast Model Version 1.0

DTIC Science & Technology

2015-04-09

can generate such as: total absorption (a), backscattering (bb), chlorophyll (chl), sea surface temperature (SST), diver visibility, etc. The...optical backscattering coefficient BSP - Battle Space Profiler CHARTS - Compact Hydrographic Airborne Rapid Total Survey Chl - Chlorophyll EO

Identification of aerosol composition from multi-wavelength lidar measurements

NASA Technical Reports Server (NTRS)

Wood, S. A.

1984-01-01

This paper seeks to develop the potential of lidar for the identification of the chemical composition of atmospheric aerosols. Available numerical computations suggest that aerosols can be identified by the wavelength dependence of aerosol optical properties. Since lidar can derive the volume backscatter coefficient as a function of wavelength, a multi-wavelength lidar system may be able to provide valuable information on the composition of aerosols. This research theoretically investigates the volume backscatter coefficients for the aerosol classes, sea-salts, and sulfates, as a function of wavelength. The results show that these aerosol compositions can be characterized and identified by their backscatter wavelength dependence. A method to utilize multi-wavelength lidar measurements to discriminate between compositionally different thin aerosol layers is discussed.

The aCORN backscatter-suppressed beta spectrometer

DOE PAGES

Hassan, M. T.; Bateman, F.; Collett, B.; ...

2017-06-16

Backscatter of electrons from a beta detector, with incomplete energy deposition, can lead to undesirable effects in many types of experiments. We present and discuss the design and operation of a backscatter-suppressed beta spectrometer that was developed as part of a program to measure the electron–antineutrino correlation coefficient in neutron beta decay (aCORN). An array of backscatter veto detectors surrounds a plastic scintillator beta energy detector. The spectrometer contains an axial magnetic field gradient, so electrons are efficiently admitted but have a low probability for escaping back through the entrance after backscattering. Lastly, the design, construction, calibration, and performance ofmore » the spectrometer are discussed.« less

Aerosol optical properties retrieved from the future space lidar mission ADM-aeolus

NASA Astrophysics Data System (ADS)

Martinet, Pauline; Flament, Thomas; Dabas, Alain

2018-04-01

The ADM-Aeolus mission, to be launched by end of 2017, will enable the retrieval of aerosol optical properties (extinction and backscatter coefficients essentially) for different atmospheric conditions. A newly developed feature finder (FF) algorithm enabling the detection of aerosol and cloud targets in the atmospheric scene has been implemented. Retrievals of aerosol properties at a better horizontal resolution based on the feature finder groups have shown an improvement mainly on the backscatter coefficient compared to the common 90 km product.

Monitoring monthly surface water dynamics of Dongting Lake using Sentinel-1 data at 10 m.

PubMed

Xing, Liwei; Tang, Xinming; Wang, Huabin; Fan, Wenfeng; Wang, Guanghui

2018-01-01

High temporal resolution water distribution maps are essential for surface water monitoring because surface water exhibits significant inner-annual variation. Therefore, high-frequency remote sensing data are needed for surface water mapping. Dongting Lake, the second-largest freshwater lake in China, is famous for the seasonal fluctuations of its inundation extents in the middle reaches of the Yangtze River. It is also greatly affected by the Three Gorges Project. In this study, we used Sentinel-1 data to generate surface water maps of Dongting Lake at 10 m resolution. First, we generated the Sentinel-1 time series backscattering coefficient for VH and VV polarizations at 10 m resolution by using a monthly composition method. Second, we generated the thresholds for mapping surface water at 10 m resolution with monthly frequencies using Sentinel-1 data. Then, we derived the monthly surface water distribution product of Dongting Lake in 2016, and finally, we analyzed the inner-annual surface water dynamics. The results showed that: (1) The thresholds were -21.56 and -15.82 dB for the backscattering coefficients for VH and VV, respectively, and the overall accuracy and Kappa coefficients were above 95.50% and 0.90, respectively, for the VH backscattering coefficient, and above 94.50% and 0.88, respectively, for the VV backscattering coefficient. The VV backscattering coefficient achieved lower accuracy due to the effect of the wind causing roughness on the surface of the water. (2) The maximum and minimum areas of surface water were 2040.33 km 2 in July, and 738.89 km 2 in December. The surface water area of Dongting Lake varied most significantly in April and August. The permanent water acreage in 2016 was 556.35 km 2 , accounting for 19.65% of the total area of Dongting Lake, and the acreage of seasonal water was 1525.21 km 2 . This study proposed a method to automatically generate monthly surface water at 10 m resolution, which may contribute to monitoring surface water in a timely manner.

Subvisual Cirrus cloud properties derived from a FIRE IFO case study

NASA Technical Reports Server (NTRS)

Sassen, Kenneth; Griffin, M. K.; Dodd, G. C.

1990-01-01

From the central Wisconsin IFO field at Wausau, the Mobile Polarization Lidar and a surface radiation station from the Lamont-Doherty Geological Observatory observed two very tenuous cirrus clouds on 21 October 1986. The clouds were present just below the height of the tropopause, between -60 to -70 C. The first cloud was not detected visually, and is classified as subvisual cirrus. The second, a relatively narrow cloud band that was probably the remnants of an aircraft contrail, can be termed zenith-subvisual since, although it was invisible in the zenith direction, it could be discerned when viewed at lower elevation angles and also due to strong solar forward-scattering and corona effects. The observations provide an opportunity to assess the threshold cloud optical thickness associated with cirrus cloud visibility. Ruby lidar backscattered signals were converted to isotropic volume backscatter coefficients by applying the pure-molecular scattering assumption just below the cloud base. The backscattering coefficient due to the cloud is then obtained and expressed in relation to the molecular backscattering coefficient in terms of the scattering ratio R. The linear depolarization ratio for the cloud is computed after removing the essentially parallel-polarized scattering contribution from air molecules. The values are also applied to determine the cloud optical thickness through the use of backscatter-to-extinction ratio, and the concentration of cloud particles using the backscattering gain, and the effective diameter of the particles obtained from the analysis of solar corona photographs. The sizes of the particles generating the corona are related to the angular separations between the centers of the red bands and the sun, yielding diameters of approximately 25 microns. The direct and diffuse components of shortwave radiation fluxes, measured by full hemispheric pyranometers, were used to compute the nadir optical thickness of the total atmosphere.

A model of the 0.4-GHz scatterometer. [used for agriculture soil moisture program

NASA Technical Reports Server (NTRS)

Wu, S. T.

1978-01-01

The 0.4 GHz aircraft scatterometer system used for the agricultural soil moisture estimation program is analyzed for the antenna pattern, the signal flow in the receiver data channels, and the errors in the signal outputs. The operational principal, system sensitivity, data handling, and resolution cell length requirements are also described. The backscattering characteristics of the agriculture scenes are contained in the form of the functional dependence of the backscattering coefficient on the incidence angle. The substantial gains of the cross-polarization term of the horizontal and vertical antennas have profound effects on the cross-polarized backscattered signals. If these signals are not corrected properly, large errors could result in the estimate of the cross-polarized backscattering coefficient. It is also necessary to correct the variations of the aircraft parameters during data processing to minimize the error in the 0 degree estimation. Recommendations are made to improve the overall performance of the scatterometer system.

Measurements of ultrasonic backscattered spectral centroid shift from spine in vivo: methodology and preliminary results.

PubMed

Garra, Brian S; Locher, Melanie; Felker, Steven; Wear, Keith A

2009-01-01

Ultrasonic backscatter measurements from vertebral bodies (L3 and L4) in nine women were performed using a clinical ultrasonic imaging system. Measurements were made through the abdomen. The location of a vertebra was identified from the bright specular reflection from the vertebral anterior surface. Backscattered signals were gated to isolate signal emanating from the cancellous interiors of vertebrae. The spectral centroid shift of the backscattered signal, which has previously been shown to correlate highly with bone mineral density (BMD) in human calcaneus in vitro, was measured. BMD was also measured in the nine subjects' vertebrae using a clinical bone densitometer. The correlation coefficient between centroid shift and BMD was r = -0.61. The slope of the linear fit was -160 kHz / (g/cm(2)). The negative slope was expected because the attenuation coefficient (and therefore magnitude of the centroid downshift) is known from previous studies to increase with BMD. The centroid shift may be a useful parameter for characterizing bone in vivo.

Re-examining the effect of particle phase functions on the remote-sensing reflectance.

PubMed

Xiong, Yuanheng; Zhang, Xiaodong; He, Shuangyan; Gray, Deric J

2017-08-20

Even though it is well known that both the magnitude and detailed angular shape of scattering (phase function, PF), particularly in the backward angles, affect the color of the ocean, the current remote-sensing reflectance (R rs ) models typically account for the effect of its magnitude only through the backscattering coefficient (b b ). Using 116 volume scattering function (VSF) measurements previously collected in three coastal waters around the U.S. and in the water of the North Atlantic Ocean, we re-examined the effect of particle PF on R rs in four scenarios. In each scenario, the magnitude of particle backscattering (i.e., b bp ) is known, but the knowledge on the angular shape of particle backscattering is assumed to increase from knowing nothing about the shape of particle PFs to partially knowing the particle backscattering ratio (B p ), the exact backscattering shape as defined by β˜ p (γ≥90°) (particle VSF normalized by the particle total scattering coefficient), and the exact backscattering shape as defined by the χ p factor (particle VSF normalized by the particle backscattering coefficient). At sun zenith angle=30°, the nadir-viewed R rs would vary up to 65%, 35%, 20%, and 10%, respectively, as the constraints on the shape of particle backscattering become increasingly stringent from scenarios 1 to 4. In all four scenarios, the R rs variations increase with both viewing and sun angles and are most prominent in the direction opposite the sun. Our results show a greater impact of the measured particle PFs on R rs than previously found, mainly because our VSF data show a much greater variability in B p , β˜ p (γ≥90°), and χ p than previously known. Among the uncertainties in R rs due to the particle PFs, about 97% can be explained by χ p , 90% by β˜ p (γ≥90°), and 27% by B p . The results indicate that the uncertainty in ocean color remote sensing can be significantly constrained by accounting for χ p of the VSFs.

C-band backscattering from corn canopies

NASA Technical Reports Server (NTRS)

Daughtry, C. S. T.; Ranson, K. J.; Biehl, L. L.

1991-01-01

A frequency-modulatad continuous-wave C-band (4.8 GHz) scatterometer was mounted on an aerial lift truck, and backscatter coefficients of corn (Zea mays L.) were acquired as functions of polarizations, view angles, and row directions. As phytomass and green-leaf area index increased, the backscatter also increased. Near anthesis, when the canopies were fully developed, the major scattering elements were located in the upper 1 m of the 2.8 m tall canopy and little backscatter was measured below that level for view angles of 30 deg or greater. C-band backscatter data could provide information to monitor tillage operations at small view zenith angles and vegetation at large view zenith angles.

Scattering from a random layer of leaves in the physical optics limit

NASA Technical Reports Server (NTRS)

Lang, R. H.; Seker, S. S.; Le Vine, D. M.

1982-01-01

Backscatter of electromagnetic radiation from a layer of vegetation over flat lossy ground has been studied in collaborative research at the George Washingnton University and the Goddard Space Flight Center. In this work the vegetation is composed of leaves which are modeled by a random collection of lossy dielectric disks. Backscattering coefficients for the vegetation layer have been calculated in the case of disks whose diameter is large compared to wavelength. These backscattering coefficients are obtained in terms of the scattering amplitude of an individual disk by employing the distorted Born procedure. The scattering amplitude for a disk which is large compared to wavelength is then found by physical optic techniques. Computed results are interpreted in terms of dominant reflected and transmitted contributions from the disks and ground.

Radar backscattering properties of corn and soybeans at frequencies of 1.6, 4.75, and 13.3. GHz

NASA Technical Reports Server (NTRS)

Paris, J. F.

1983-01-01

The NASA Johnson Space Center made an observational study of the radar-backscattering properties of corn and soybeans in commercial fields in a test site in Webster County, IA. Aircraft-based radar scatterometers measured the backscattering coefficient of the crops at three frequencies, 1.6 GHz (L-band), 4.75 GHz (C-band), and 13.3 GHz (Ku-band), at 10 sensor look-angles (5 to 50 degrees from the nadir in steps of 5 degrees), and with several polarization combinations. Among other findings, it was determined that: (1) row direction differences among fields affected significantly the radar-backscattering coefficient of the fields when the radar system used like-polarization at look-angles from 5 to 25 degrees; (2) row-direction differences had no effect on radar backscattering when the system used either cross-polarization or look-angles greater than 25 degrees regardless of the polarization; (3) wet surface-soil moisture conditions resulted in significantly poorer spectral separability of the two crops as compared to dry-soil conditions; and (4) on the dry-soil date, the best channel for separating corn from soybeans was the C-band cross-polarized measurement at a look-angle of 50 degrees.

An Accuracy Assessment of the CALIOP/CALIPSO Version 2/Version 3 Daytime Aerosol Extinction Product Based on a Detailed Multi-Sensor, Multi-Platform Case Study

NASA Technical Reports Server (NTRS)

Kacenelenbogen, M.; Vaughan, M. A.; Redemann, J.; Hoff, R. M.; Rogers, R. R.; Ferrare, R. A.; Russell, P. B.; Hostetler, C. A.; Hair, J. W.; Holben, B. N.

2011-01-01

The Cloud Aerosol LIdar with Orthogonal Polarization (CALIOP), on board the CALIPSO platform, has measured profiles of total attenuated backscatter coefficient (level 1 products) since June 2006. CALIOP s level 2 products, such as the aerosol backscatter and extinction coefficient profiles, are retrieved using a complex succession of automated algorithms. The goal of this study is to help identify potential shortcomings in the CALIOP version 2 level 2 aerosol extinction product and to illustrate some of the motivation for the changes that have been introduced in the next version of CALIOP data (version 3, released in June 2010). To help illustrate the potential factors contributing to the uncertainty of the CALIOP aerosol extinction retrieval, we focus on a one-day, multi-instrument, multiplatform comparison study during the CALIPSO and Twilight Zone (CATZ) validation campaign on 4 August 2007. On that day, we observe a consistency in the Aerosol Optical Depth (AOD) values recorded by four different instruments (i.e. spaceborne MODerate Imaging Spectroradiometer, MODIS: 0.67 and POLarization and Directionality of Earth s Reflectances, POLDER: 0.58, airborne High Spectral Resolution Lidar, HSRL: 0.52 and ground-based AErosol RObotic NETwork, AERONET: 0.48 to 0.73) while CALIOP AOD is a factor of two lower (0.32 at 532 nm). This case study illustrates the following potential sources of uncertainty in the CALIOP AOD: (i) CALIOP s low signal-to-noise ratio (SNR) leading to the misclassification and/or lack of aerosol layer identification, especially close to the Earth s surface; (ii) the cloud contamination of CALIOP version 2 aerosol backscatter and extinction profiles; (iii) potentially erroneous assumptions of the aerosol extinction-to-backscatter ratio (Sa) used in CALIOP s extinction retrievals; and (iv) calibration coefficient biases in the CALIOP daytime attenuated backscatter coefficient profiles. The use of version 3 CALIOP extinction retrieval for our case study seems to partially fix factor (i) although the aerosol retrieved by CALIOP is still somewhat lower than the profile measured by HSRL; the cloud contamination (ii) appears to be corrected; no particular change is apparent in the observation-based CALIOP Sa value (iii). Our case study also showed very little difference in version 2 and version 3 CALIOP attenuated backscatter coefficient profiles, illustrating a minor change in the calibration scheme (iv).

Seasonal And Regional Differentiation Of Bio-Optical Properties Within The North Polar Atlantic

NASA Technical Reports Server (NTRS)

Stramska, Malgorzata; Stramski, Dariusz; Kaczmarek, Slawomir; Allison, David B.; Schwarz, Jill

2005-01-01

Using data collected during spring and summer seasons in the north polar Atlantic we examined the variability of the spectral absorption, a(lambda), and backscattering, b(sub b)(lambda), coefficients of surface waters and its relation to phytoplankton pigment concentration and composition. For a given chlorophyll a concentration (TChla), the concentrations of photosynthetic carotenoids (PSC), photoprotective carotenoids (PPC), and total accessory pigments (AP) were consistently lower in spring than in summer. The chlorophyll-specific absorption coefficients of phytoplankton and total particulate matter were also lower in spring, which can be partly attributed to lower proportions of PPC, PSC, and AP in spring. The spring values of the green-to-blue band ratio of the absorption coefficient were higher than the summer ratios. The blue-to-green ratios of backscattering coefficient were also higher in spring. The higher b(sub b) values and lower blue-to-green b(sub b) ratios in summer were likely associated with higher concentrations of detrital particles in summer compared to spring. Because the product of the green-to-blue absorption ratio and the blue-to-green backscattering ratio is a proxy for the blue-to-green ratio of remote-sensing reflectance, we conclude that the performance of ocean color band-ratio algorithms for estimating pigments in the north polar Atlantic is significantly affected by seasonal shifts in the relationships between absorption and TChla as well as between backscattering and TChla. Intriguingly, however, fairly good estimate of the particulate beam attenuation coefficient at 660 nm (potential measure of total particulate matter or particulate organic carbon concentration) can be obtained by applying a single blue-to-green band-ratio algorithm for both spring and summer seasons.

Forest above ground biomass estimation and forest/non-forest classification for Odisha, India, using L-band Synthetic Aperture Radar (SAR) data

NASA Astrophysics Data System (ADS)

Suresh, M.; Kiran Chand, T. R.; Fararoda, R.; Jha, C. S.; Dadhwal, V. K.

2014-11-01

Tropical forests contribute to approximately 40 % of the total carbon found in terrestrial biomass. In this context, forest/non-forest classification and estimation of forest above ground biomass over tropical regions are very important and relevant in understanding the contribution of tropical forests in global biogeochemical cycles, especially in terms of carbon pools and fluxes. Information on the spatio-temporal biomass distribution acts as a key input to Reducing Emissions from Deforestation and forest Degradation Plus (REDD+) action plans. This necessitates precise and reliable methods to estimate forest biomass and to reduce uncertainties in existing biomass quantification scenarios. The use of backscatter information from a host of allweather capable Synthetic Aperture Radar (SAR) systems during the recent past has demonstrated the potential of SAR data in forest above ground biomass estimation and forest / nonforest classification. In the present study, Advanced Land Observing Satellite (ALOS) / Phased Array L-band Synthetic Aperture Radar (PALSAR) data along with field inventory data have been used in forest above ground biomass estimation and forest / non-forest classification over Odisha state, India. The ALOSPALSAR 50 m spatial resolution orthorectified and radiometrically corrected HH/HV dual polarization data (digital numbers) for the year 2010 were converted to backscattering coefficient images (Schimada et al., 2009). The tree level measurements collected during field inventory (2009-'10) on Girth at Breast Height (GBH at 1.3 m above ground) and height of all individual trees at plot (plot size 0.1 ha) level were converted to biomass density using species specific allometric equations and wood densities. The field inventory based biomass estimations were empirically integrated with ALOS-PALSAR backscatter coefficients to derive spatial forest above ground biomass estimates for the study area. Further, The Support Vector Machines (SVM) based Radial Basis Function classification technique was employed to carry out binary (forest-non forest) classification using ALOSPALSAR HH and HV backscatter coefficient images and field inventory data. The textural Haralick's Grey Level Cooccurrence Matrix (GLCM) texture measures are determined on HV backscatter image for Odisha, for the year 2010. PALSAR HH, HV backscatter coefficient images, their difference (HHHV) and HV backscatter coefficient based eight textural parameters (Mean, Variance, Dissimilarity, Contrast, Angular second moment, Homogeneity, Correlation and Contrast) are used as input parameters for Support Vector Machines (SVM) tool. Ground based inputs for forest / non-forest were taken from field inventory data and high resolution Google maps. Results suggested significant relationship between HV backscatter coefficient and field based biomass (R2 = 0.508, p = 0.55) compared to HH with biomass values ranging from 5 to 365 t/ha. The spatial variability of biomass with reference to different forest types is in good agreement. The forest / nonforest classified map suggested a total forest cover of 50214 km2 with an overall accuracy of 92.54 %. The forest / non-forest information derived from the present study showed a good spatial agreement with the standard forest cover map of Forest Survey of India (FSI) and corresponding published area of 50575 km2. Results are discussed in the paper.

Active microwave remote sensing of an anisotropic random medium layer

NASA Technical Reports Server (NTRS)

Lee, J. K.; Kong, J. A.

1985-01-01

A two-layer anisotropic random medium model has been developed to study the active remote sensing of the earth. The dyadic Green's function for a two-layer anisotropic medium is developed and used in conjunction with the first-order Born approximation to calculate the backscattering coefficients. It is shown that strong cross-polarization occurs in the single scattering process and is indispensable in the interpretation of radar measurements of sea ice at different frequencies, polarizations, and viewing angles. The effects of anisotropy on the angular responses of backscattering coefficients are also illustrated.

I Vivo Quantitative Ultrasound Imaging and Scatter Assessments.

NASA Astrophysics Data System (ADS)

Lu, Zheng Feng

There is evidence that "instrument independent" measurements of ultrasonic scattering properties would provide useful diagnostic information that is not available with conventional ultrasound imaging. This dissertation is a continuing effort to test the above hypothesis and to incorporate quantitative ultrasound methods into clinical examinations for early detection of diffuse liver disease. A well-established reference phantom method was employed to construct quantitative ultrasound images of tissue in vivo. The method was verified by extensive phantom tests. A new method was developed to measure the effective attenuation coefficient of the body wall. The method relates the slope of the difference between the echo signal power spectrum from a uniform region distal to the body wall and the echo signal power spectrum from a reference phantom to the body wall attenuation. The accuracy obtained from phantom tests suggests further studies with animal experiments. Clinically, thirty-five healthy subjects and sixteen patients with diffuse liver disease were studied by these quantitative ultrasound methods. The average attenuation coefficient in normals agreed with previous investigators' results; in vivo backscatter coefficients agreed with the results from normals measured by O'Donnell. Strong discriminating power (p < 0.001) was found for both attenuation and backscatter coefficients between fatty livers and normals; a significant difference (p < 0.01) was observed in the backscatter coefficient but not in the attenuation coefficient between cirrhotic livers and normals. An in vivo animal model of steroid hepatopathy was used to investigate the system sensitivity in detecting early changes in canine liver resulting from corticosteroid administration. The average attenuation coefficient slope increased from 0.7 dB/cm/MHz in controls to 0.82 dB/cm/MHz (at 6 MHz) in treated animals on day 14 into the treatment, and the backscatter coefficient was 26times 10^{ -4}cm^{-1}sr^{-1} in controls compared with 74times 10^{-4}cm^{-1}sr^ {-1} (at 6 MHz) in treated animals. A simplified quantitative approach using video image signals was developed. Results derived both from the r.f. signal analysis and from the video signal analysis are sensitive to the changes in the liver in this animal model.

Optical properties of Southern Hemisphere aerosols: Report of the joint CSIRO/NASA study

NASA Technical Reports Server (NTRS)

Gras, John L.; Platt, C. Martin; Huffaker, R. Milton; Jones, William D.; Kavaya, Michael J.; Gras, John L.

1988-01-01

This study was made in support of the LAWS and GLOBE programs, which aim to design a suitable Doppler lidar system for measuring global winds from a satellite. Observations were taken from 5 deg S to 45 deg S along and off the E and SE Australian coast, thus obtaining representative samples over a large latitude range. Observations were made between 0 and 6 km altitude of aerosol physical and chemical properties in situ from the CSIRO F-27 aircraft; of lidar backscatter coefficients at 10.6 micron wavelength from the F-27 aircraft; of lidar backscatter profiles at 0.694 microns at Sale, SE Australia; and of lidar backscatter profiles at 0.532 microns at Cowley Beach, NE Australia. Both calculations and observations in the free troposphere gave a backscatter coefficient of 1-2 x 10 to the -11/m/sr at 10.6 microns, although the accuracies of the instruments were marginal at this level. Equivalent figures were 2-8 x 10 to the -9/m/sr (aerosol) and 9 x 10 to the -9 to 2 x 10 to the -8/m/sr (lidar) at 0.694 microns wavelength at Sale; and 3.7 x 10 to the -9/m/sr (aerosol) and 10 to the -8 to 10 to the -7/m/sr (lidar) at 0.532 microns wavelength at Cowley Beach. The measured backscatter coefficients at 0.694 and 0.532 microns were consistently higher than the values calculated from aerosol size distributions by factors of typically 2 to 10.

A framework to quantify uncertainties of seafloor backscatter from swath mapping echosounders

NASA Astrophysics Data System (ADS)

Malik, Mashkoor; Lurton, Xavier; Mayer, Larry

2018-06-01

Multibeam echosounders (MBES) have become a widely used acoustic remote sensing tool to map and study the seafloor, providing co-located bathymetry and seafloor backscatter. Although the uncertainty associated with MBES-derived bathymetric data has been studied extensively, the question of backscatter uncertainty has been addressed only minimally and hinders the quantitative use of MBES seafloor backscatter. This paper explores approaches to identifying uncertainty sources associated with MBES-derived backscatter measurements. The major sources of uncertainty are catalogued and the magnitudes of their relative contributions to the backscatter uncertainty budget are evaluated. These major uncertainty sources include seafloor insonified area (1-3 dB), absorption coefficient (up to > 6 dB), random fluctuations in echo level (5.5 dB for a Rayleigh distribution), and sonar calibration (device dependent). The magnitudes of these uncertainty sources vary based on how these effects are compensated for during data acquisition and processing. Various cases (no compensation, partial compensation and full compensation) for seafloor insonified area, transmission losses and random fluctuations were modeled to estimate their uncertainties in different scenarios. Uncertainty related to the seafloor insonified area can be reduced significantly by accounting for seafloor slope during backscatter processing while transmission losses can be constrained by collecting full water column absorption coefficient profiles (temperature and salinity profiles). To reduce random fluctuations to below 1 dB, at least 20 samples are recommended to be used while computing mean values. The estimation of uncertainty in backscatter measurements is constrained by the fact that not all instrumental components are characterized and documented sufficiently for commercially available MBES. Further involvement from manufacturers in providing this essential information is critically required.

A three-part geometric model to predict the radar backscatter from wheat, corn, and sorghum

NASA Technical Reports Server (NTRS)

Ulaby, F. T. (Principal Investigator); Eger, G. W., III; Kanemasu, E. T.

1982-01-01

A model to predict the radar backscattering coefficient from crops must include the geometry of the canopy. Radar and ground-truth data taken on wheat in 1979 indicate that the model must include contributions from the leaves, from the wheat head, and from the soil moisture. For sorghum and corn, radar and ground-truth data obtained in 1979 and 1980 support the necessity of a soil moisture term and a leaf water term. The Leaf Area Index (LAI) is an appropriate input for the leaf contribution to the radar response for wheat and sorghum, however the LAI generates less accurate values for the backscattering coefficient for corn. Also, the data for corn and sorghum illustrate the importance of the water contained in the stalks in estimating the radar response.

The characteristics simulation of FMCW laser backscattering signals

NASA Astrophysics Data System (ADS)

Liu, Bohu; Song, Chengtian; Duan, Yabo

2018-04-01

A Monte Carlo simulation model of FMCW laser transmission in a smoke interference environment was established in this paper. The aerosol extinction coefficient and scattering coefficient changed dynamically in the simulation according to the smoke concentration variation, aerosol particle distributions and photon spatial positions. The simulation results showed that the smoke backscattering interference produced a number of amplitude peaks in the beat signal spectrum; the SNR of target echo signal to smoke interference was related to the transmitted laser wavelength and the aerosol particle size distribution; a better SNR could be obtained when the laser wavelength was in the range of 560-1660 nm. The characteristics of FMCW laser backscattering signals generated by simulation are consistent with the theoretical analysis. Therefore, this study was greatly helpful for improving the ability of identifying target and anti-interference in the further research.

Spectroradiometric monitoring for open outdoor culturing of algae and cyanobacteria.

PubMed

Reichardt, Thomas A; Collins, Aaron M; McBride, Robert C; Behnke, Craig A; Timlin, Jerilyn A

2014-08-20

We assess the measurement of hyperspectral reflectance for outdoor monitoring of green algae and cyanobacteria cultures with a multichannel, fiber-coupled spectroradiometer. Reflectance data acquired over a 4-week period are interpreted via numerical inversion of a reflectance model, in which the above-water reflectance is expressed as a quadratic function of the single backscattering albedo, which is dependent on the absorption and backscatter coefficients. The absorption coefficient is treated as the sum of component spectra consisting of the cultured species (green algae or cyanobacteria), dissolved organic matter, and water (including the temperature dependence of the water absorption spectrum). The backscatter coefficient is approximated as the scaled Hilbert transform of the culture absorption spectrum with a wavelength-independent vertical offset. Additional terms in the reflectance model account for the pigment fluorescence features and the water-surface reflection of sunlight and skylight. For the green algae and cyanobacteria, the wavelength-independent vertical offset of the backscatter coefficient is found to scale linearly with daily dry weight measurements, providing the capability for a nonsampling measurement of biomass in outdoor ponds. Other fitting parameters in the reflectance model are compared with auxiliary measurements and physics-based calculations. The model-derived magnitudes of sunlight and skylight water-surface reflections compare favorably with Fresnel reflectance calculations, while the model-derived quantum efficiency of Chl-a fluorescence is found to be in agreement with literature values. Finally, the water temperatures derived from the reflectance model exhibit excellent agreement with thermocouple measurements during the morning hours but correspond to significantly elevated temperatures in the afternoon hours.

Remote sensing of particle dynamics: a two-component unmixing model in a western UK shelf sea.

NASA Astrophysics Data System (ADS)

Mitchell, Catherine; Cunningham, Alex

2014-05-01

The relationship between the backscattering and absorption coefficients, in particular the backscattering to absorption ratio, is mediated by the type of particles present in the water column. By considering the optical signals to be driven by phytoplankton and suspended minerals, with a relatively constant influence from CDOM, radiative transfer modelling is used to propose a method for retrieving the optical contribution of phytoplankton and suspended minerals to the total absorption coefficient with mean percentage errors of below 5% for both components. These contributions can be converted to constituent concentrations if the appropriate specific inherent optical properties are known or can be determined from the maximum and minimum backscattering to absorption ratios of the data. Remotely sensed absorption and backscattering coefficients from eight years of MODIS data for the Irish Sea reveal maximum backscattering to absorption coefficient ratios over the winter (with an average for the region of 0.27), which then decrease to a minimum over the summer months (with an average of 0.06) before increasing again through to winter, indicating a change in the particles present in the water column. Application of the two-component unmixing model to this data showed seasonal cycles of both phytoplankton and suspended mineral concentrations which vary in both amplitude and periodicity depending on their location. For example, in the Bristol Channel the amplitude of the suspended mineral concentration throughout one cycle is approximately 75% greater than a yearly cycle in the eastern Irish Sea. These seasonal cycles give an insight into the complex dynamics of particles in the water column, indicating the suspension of sediment throughout the winter months and the loss of sediments from the surface layer over the summer during stratification. The relationship between the timing of the phytoplankton spring bloom and changes in the availability of light in the water column can be studied to gain an understanding into the phytoplankton phenology across the region.

Quantitative Ultrasound: Transition from the Laboratory to the Clinic

NASA Astrophysics Data System (ADS)

Hall, Timothy

2014-03-01

There is a long history of development and testing of quantitative methods in medical ultrasound. From the initial attempts to scan breasts with ultrasound in the early 1950's, there was a simultaneous attempt to classify tissue as benign or malignant based on the appearance of the echo signal on an oscilloscope. Since that time, there has been substantial improvement in the ultrasound systems used, the models to describe wave propagation in random media, the methods of signal detection theory, and the combination of those models and methods into parameter estimation techniques. One particularly useful measure in ultrasonics is the acoustic differential scattering cross section per unit volume in the special case of the 180° (as occurs in pulse-echo ultrasound imaging) which is known as the backscatter coefficient. The backscatter coefficient, and parameters derived from it, can be used to objectively measure quantities that are used clinically to subjectively describe ultrasound images. For example, the ``echogenicity'' (relative ultrasound image brightness) of the renal cortex is commonly compared to that of the liver. Investigating the possibility of liver disease, it is assumed the renal cortex echogenicity is normal. Investigating the kidney, it is assumed the liver echogenicity is normal. Objective measures of backscatter remove these assumptions. There is a 30-year history of accurate estimates of acoustic backscatter coefficients with laboratory systems. Twenty years ago that ability was extended to clinical imaging systems with array transducers. Recent studies involving multiple laboratories and a variety of clinical imaging systems has demonstrated system-independent estimates of acoustic backscatter coefficients in well-characterized media (agreement within about 1.5dB over about a 1-decade frequency range). Advancements that made this possible, transition of this and similar capabilities into medical practice and the prospects for quantitative image-based biomarkers will be discussed. This work was supported, in part, by NIH grants R01CA140271 and R01HD072077.

Multiangle lidar observations of the Atmosphere

NASA Astrophysics Data System (ADS)

Lalitkumar Prakash, Pawar; Choukiker, Yogesh Kumar; Raghunath, K.

2018-04-01

Atmospheric Lidars are used extensively to get aerosol parameters like backscatter coefficient, backscatter ratio etc. National Atmospheric Research Laboratory, Gadanki (13°N, 79°E), India has a powerful lidar which has alt-azimuth capability. Inversion method is applied to data from observations of lidar system at different azimuth and elevation angles. Data Analysis is described and Observations in 2D and 3D format are discussed. Presence of Cloud and the variation of backscatter parameters are seen in an interesting manner.

Monte Carlo simulations of coherent backscatter for identification of the optical coefficients of biological tissues in vivo

NASA Astrophysics Data System (ADS)

Eddowes, M. H.; Mills, T. N.; Delpy, D. T.

1995-05-01

A Monte Carlo model of light backscattered from turbid media has been used to simulate the effects of weak localization in biological tissues. A validation technique is used that implies that for the scattering and absorption coefficients and for refractive index mismatches found in tissues, the Monte Carlo method is likely to provide more accurate results than the methods previously used. The model also has the ability to simulate the effects of various illumination profiles and other laboratory-imposed conditions. A curve-fitting routine has been developed that might be used to extract the optical coefficients from the angular intensity profiles seen in experiments on turbid biological tissues, data that could be obtained in vivo.

Evolution of the Pinatubo volcanic aerosol column above Pasadena, California observed with a mid-infrared backscatter lidar

NASA Technical Reports Server (NTRS)

Tratt, David M.; Menzies, Robert T.

1995-01-01

The evolution of the volcanic debris plume originating from the June 1991 eruption of Mt. Pinatubo has been monitored since its genesis using a ground-based backscatter lidar facility sited at the Jet Propulsion Laboratory (JPL). Both absolute and relative pre- and post-Pinatubo backscatter observations are in accord with Mie scattering projections based on measured aerosol particle size distributions reported in the literature. The post-Pinatubo column-integrated backscatter coefficient peaked approximately 400 days after the eruption, and the observed upper boundary of the aerosol column subsided at a rate of approximately 200 m/mon.

A scattering model for forested area

NASA Technical Reports Server (NTRS)

Karam, M. A.; Fung, A. K.

1988-01-01

A forested area is modeled as a volume of randomly oriented and distributed disc-shaped, or needle-shaped leaves shading a distribution of branches modeled as randomly oriented finite-length, dielectric cylinders above an irregular soil surface. Since the radii of branches have a wide range of sizes, the model only requires the length of a branch to be large compared with its radius which may be any size relative to the incident wavelength. In addition, the model also assumes the thickness of a disc-shaped leaf or the radius of a needle-shaped leaf is much smaller than the electromagnetic wavelength. The scattering phase matrices for disc, needle, and cylinder are developed in terms of the scattering amplitudes of the corresponding fields which are computed by the forward scattering theorem. These quantities along with the Kirchoff scattering model for a randomly rough surface are used in the standard radiative transfer formulation to compute the backscattering coefficient. Numerical illustrations for the backscattering coefficient are given as a function of the shading factor, incidence angle, leaf orientation distribution, branch orientation distribution, and the number density of leaves. Also illustrated are the properties of the extinction coefficient as a function of leaf and branch orientation distributions. Comparisons are made with measured backscattering coefficients from forested areas reported in the literature.

Feasibility of sea ice typing with synthetic aperture radar (SAR): Merging of Landsat thematic mapper and ERS 1 SAR satellite imagery

NASA Technical Reports Server (NTRS)

Steffen, Konrad; Heinrichs, John

1994-01-01

Earth Remote-Sensing Satellite (ERS) 1 synthetic aperture radar (SAR) and Landsat thematic mapper (TM) images were acquired for the same area in the Beaufort Sea, April 16 and 18, 1992. The two image pairs were colocated to the same grid (25-m resolution), and a supervised ice type classification was performed on the TM images in order to classify ice free, nilas, gray ice, gray-white ice, thin first-year ice, medium and thick first-year ice, and old ice. Comparison of the collocated SAR pixels showed that ice-free areas can only be classified under calm wind conditions (less than 3 m/s) and for surface winds greater than 10 m/s based on the backscattering coefficient alone. This is true for pack ice regions during the cold months of the year where ice-free areas are spatially limited and where the capillary waves that cause SAR backscatter are dampened by entrained ice crystals. For nilas, two distinct backscatter classes were found at -17 dB and at -10 dB. The higher backscattering coefficient is attributed to the presence of frost flowers on light nilas. Gray and gray-white ice have a backscatter signature similar to first-year ice and therefore cannot be distinguished by SAR alone. First-year and old ice can be clearly separated based on their backscattering coefficient. The performance of the Geophysical Processor System ice classifier was tested against the Landsat derived ice products. It was found that smooth first-year ice and rough first-year ice were not significantly different in the backscatter domain. Ice concentration estimates based on ERS 1 C band SAR showed an error range of 5 to 8% for high ice concentration regions, mainly due to misclassified ice-free and smooth first-year ice areas. This error is expected to increase for areas of lower ice concentration. The combination of C band SAR and TM channels 2, 4, and 6 resulted in ice typing performance with an estimated accuracy of 90% for all seven ice classes.

Relating the radar backscattering coefficient to leaf-area index

NASA Technical Reports Server (NTRS)

Ulaby, F. T. (Principal Investigator); Allen, C.; Eger, G.; Kanemasu, E.

1983-01-01

The relationship between the radar backscattering coefficient of a vegetation canopy, sigma(0) sub can, and the canopy's leaf area index (LAI) is examined. The relationship is established through the development of a model for corn and sorghum and another for wheat. Both models are extensions of the cloud model of Attema and Ulaby (1978). Analysis of experimental data measured at 8.6, 13.0, 17.0, and 35.6 GHz indicates that most of the temporal variations of sigma(0) sub can can be accounted for through variations in green LAI alone, if the latter is greater than 0.5.

On the non-closure of particle backscattering coefficient in oligotrophic oceans.

PubMed

Lee, ZhongPing; Huot, Yannick

2014-11-17

Many studies have consistently found that the particle backscattering coefficient (bbp) in oligotrophic oceans estimated from remote-sensing reflectance (Rrs) using semi-analytical algorithms is higher than that from in situ measurements. This overestimation can be as high as ~300% for some oligotrophic ocean regions. Various sources potentially responsible for this discrepancy are examined. Further, after applying an empirical algorithm to correct the impact from Raman scattering, it is found that bbp from analytical inversion of Rrs is in good agreement with that from in situ measurements, and that a closure is achieved.

Understanding the context of balanced scorecard implementation: a hospital-based case study in Pakistan.

PubMed

Rabbani, Fauziah; Lalji, Sabrina Nh; Abbas, Farhat; Jafri, Sm Wasim; Razzak, Junaid A; Nabi, Naheed; Jahan, Firdous; Ajmal, Agha; Petzold, Max; Brommels, Mats; Tomson, Goran

2011-03-31

As a response to a changing operating environment, healthcare administrators are implementing modern management tools in their organizations. The balanced scorecard (BSC) is considered a viable tool in high-income countries to improve hospital performance. The BSC has not been applied to hospital settings in low-income countries nor has the context for implementation been examined. This study explored contextual perspectives in relation to BSC implementation in a Pakistani hospital. Four clinical units of this hospital were involved in the BSC implementation based on their willingness to participate. Implementation included sensitization of units towards the BSC, developing specialty specific BSCs and reporting of performance based on the BSC during administrative meetings. Pettigrew and Whipp's context (why), process (how) and content (what) framework of strategic change was used to guide data collection and analysis. Data collection methods included quantitative tools (a validated culture assessment questionnaire) and qualitative approaches including key informant interviews and participant observation. Method triangulation provided common and contrasting results between the four units. A participatory culture, supportive leadership, financial and non-financial incentives, the presentation of clear direction by integrating support for the BSC in policies, resources, and routine activities emerged as desirable attributes for BSC implementation. The two units that lagged behind were more involved in direct inpatient care and carried a considerable clinical workload. Role clarification and consensus about the purpose and benefits of the BSC were noted as key strategies for overcoming implementation challenges in two clinical units that were relatively ahead in BSC implementation. It was noted that, rather than seeking to replace existing information systems, initiatives such as the BSC could be readily adopted if they are built on existing infrastructures and data networks. Variable levels of the BSC implementation were observed in this study. Those intending to apply the BSC in other hospital settings need to ensure a participatory culture, clear institutional mandate, appropriate leadership support, proper reward and recognition system, and sensitization to BSC benefits.

Hyperspectral absorption and backscattering coefficients of bulk water retrieved from a combination of remote-sensing reflectance and attenuation coefficient.

PubMed

Lin, Junfang; Lee, Zhongping; Ondrusek, Michael; Liu, Xiaohan

2018-01-22

Absorption (a) and backscattering (bb) coefficients play a key role in determining the light field; they also serve as the link between remote sensing and concentrations of optically active water constituents. Here we present an updated scheme to derive hyperspectral a and bb with hyperspectral remote-sensing reflectance (Rrs) and diffuse attenuation coefficient (Kd) as the inputs. Results show that the system works very well from clear open oceans to highly turbid inland waters, with an overall difference less than 25% between these retrievals and those from instrument measurements. This updated scheme advocates the measurement and generation of hyperspectral a and bb from hyperspectral Rrs and Kd, as an independent data source for cross-evaluation of in situ measurements of a and bb and for the development and/or evaluation of remote sensing algorithms for such optical properties.

Microwave inversion of leaf area and inclination angle distributions from backscattered data

NASA Technical Reports Server (NTRS)

Lang, R. H.; Saleh, H. A.

1985-01-01

The backscattering coefficient from a slab of thin randomly oriented dielectric disks over a flat lossy ground is used to reconstruct the inclination angle and area distributions of the disks. The disks are employed to model a leafy agricultural crop, such as soybeans, in the L-band microwave region of the spectrum. The distorted Born approximation, along with a thin disk approximation, is used to obtain a relationship between the horizontal-like polarized backscattering coefficient and the joint probability density of disk inclination angle and disk radius. Assuming large skin depth reduces the relationship to a linear Fredholm integral equation of the first kind. Due to the ill-posed nature of this equation, a Phillips-Twomey regularization method with a second difference smoothing condition is used to find the inversion. Results are obtained in the presence of 1 and 10 percent noise for both leaf inclination angle and leaf radius densities.

The impact of absorption coefficient on polarimetric determination of Berry phase based depth resolved characterization of biomedical scattering samples: a polarized Monte Carlo investigation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baba, Justin S; Koju, Vijay; John, Dwayne O

2016-01-01

The modulation of the state of polarization of photons due to scatter generates associated geometric phase that is being investigated as a means for decreasing the degree of uncertainty in back-projecting the paths traversed by photons detected in backscattered geometry. In our previous work, we established that polarimetrically detected Berry phase correlates with the mean photon penetration depth of the backscattered photons collected for image formation. In this work, we report on the impact of state-of-linear-polarization (SOLP) filtering on both the magnitude and population distributions of image forming detected photons as a function of the absorption coefficient of the scatteringmore » sample. The results, based on Berry phase tracking implemented Polarized Monte Carlo Code, indicate that sample absorption plays a significant role in the mean depth attained by the image forming backscattered detected photons.« less

Retrieval of ice thickness from polarimetric SAR data

NASA Technical Reports Server (NTRS)

Kwok, R.; Yueh, S. H.; Nghiem, S. V.; Huynh, D. D.

1993-01-01

We describe a potential procedure for retrieving ice thickness from multi-frequency polarimetric SAR data for thin ice. This procedure includes first masking out the thicker ice types with a simple classifier and then deriving the thickness of the remaining pixels using a model-inversion technique. The technique used to derive ice thickness from polarimetric observations is provided by a numerical estimator or neural network. A three-layer perceptron implemented with the backpropagation algorithm is used in this investigation with several improved aspects for a faster convergence rate and a better accuracy of the neural network. These improvements include weight initialization, normalization of the output range, the selection of offset constant, and a heuristic learning algorithm. The performance of the neural network is demonstrated by using training data generated by a theoretical scattering model for sea ice matched to the database of interest. The training data are comprised of the polarimetric backscattering coefficients of thin ice and the corresponding input ice parameters to the scattering model. The retrieved ice thickness from the theoretical backscattering coefficients is compare with the input ice thickness to the scattering model to illustrate the accuracy of the inversion method. Results indicate that the network convergence rate and accuracy are higher when multi-frequency training sets are presented. In addition, the dominant backscattering coefficients in retrieving ice thickness are found by comparing the behavior of the network trained backscattering data at various incidence angels. After the neural network is trained with the theoretical backscattering data at various incidence anges, the interconnection weights between nodes are saved and applied to the experimental data to be investigated. In this paper, we illustrate the effectiveness of this technique using polarimetric SAR data collected by the JPL DC-8 radar over a sea ice scene.

Modeling L-band synthetic aperture radar observations through dielectric changes in soil moisture and vegetation over shrublands

USDA-ARS?s Scientific Manuscript database

L-band airborne synthetic aperture radar observations were made over California shrublands to better understand the effects by soil and vegetation parameters on backscatter. Temporal changes in radar backscattering coefficient (s0) of up to 3 dB were highly correlated to surface soil moisture but no...

Backscattering of electrons from solid targets

NASA Astrophysics Data System (ADS)

Dapor, Maurizio

1990-11-01

A simple equation is derived which describes the electron backscattering coefficient as a function of the target atomic number in the primary energy range 2-45 KeV. Such an equation, very useful for practical purposes, is in better agreement with the experimental data of Palluel and of Cosslett and Thomas than both the treatments of Everhart and of Archard.

Spectroradiometric monitoring for open outdoor culturing of algae and cyanobacteria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reichardt, Thomas A.; Collins, Aaron M.; McBride, Robert C.

We assess the measurement of hyperspectral reflectance for the outdoor monitoring of green algae and cyanobacteria cultures with a multi-channel, fiber-coupled spectroradiometer. Reflectance data acquired over a four-week period are interpreted via numerical inversion of a reflectance model, in which the above-water reflectance is expressed as a quadratic function of the single backscattering albedo, dependent on the absorption and backscatter coefficients. The absorption coefficient is treated as the sum of component spectra consisting of the cultured species (green algae or cyanobacteria), dissolved organic matter, and water (including the temperature dependence of the water absorption spectrum). The backscatter coefficient is approximatedmore » as the scaled Hilbert transform of the culture absorption spectrum with a wavelength-independent vertical offset. Additional terms in the reflectance model account for the pigment fluorescence features and the water surface reflection of sunlight and skylight. For both the green algae and cyanobacteria, the wavelength-independent vertical offset of the backscatter coefficient is found to scale linearly with daily dry weight measurements, providing the capability for a non-sampling measurement of biomass in outdoor ponds. Other fitting parameters in the reflectance model are compared to auxiliary measurements and physics-based calculations. The magnitudes of the sunlight and skylight water-surface contributions derived from the reflectance model compare favorably with Fresnel reflectance calculations, while the reflectance-derived quantum efficiency of Chl-a fluorescence is found to be in agreement with literature values. To conlclude, the water temperature derived from the reflectance model exhibits excellent agreement with thermocouple measurements during the morning hours and highlights significantly elevated temperatures in the afternoon hours.« less

Spectroradiometric monitoring for open outdoor culturing of algae and cyanobacteria

DOE PAGES

Reichardt, Thomas A.; Collins, Aaron M.; McBride, Robert C.; ...

2014-08-20

We assess the measurement of hyperspectral reflectance for the outdoor monitoring of green algae and cyanobacteria cultures with a multi-channel, fiber-coupled spectroradiometer. Reflectance data acquired over a four-week period are interpreted via numerical inversion of a reflectance model, in which the above-water reflectance is expressed as a quadratic function of the single backscattering albedo, dependent on the absorption and backscatter coefficients. The absorption coefficient is treated as the sum of component spectra consisting of the cultured species (green algae or cyanobacteria), dissolved organic matter, and water (including the temperature dependence of the water absorption spectrum). The backscatter coefficient is approximatedmore » as the scaled Hilbert transform of the culture absorption spectrum with a wavelength-independent vertical offset. Additional terms in the reflectance model account for the pigment fluorescence features and the water surface reflection of sunlight and skylight. For both the green algae and cyanobacteria, the wavelength-independent vertical offset of the backscatter coefficient is found to scale linearly with daily dry weight measurements, providing the capability for a non-sampling measurement of biomass in outdoor ponds. Other fitting parameters in the reflectance model are compared to auxiliary measurements and physics-based calculations. The magnitudes of the sunlight and skylight water-surface contributions derived from the reflectance model compare favorably with Fresnel reflectance calculations, while the reflectance-derived quantum efficiency of Chl-a fluorescence is found to be in agreement with literature values. To conlclude, the water temperature derived from the reflectance model exhibits excellent agreement with thermocouple measurements during the morning hours and highlights significantly elevated temperatures in the afternoon hours.« less

Development and application of a backscatter lidar forward operator for quantitative validation of aerosol dispersion models and future data assimilation

NASA Astrophysics Data System (ADS)

Geisinger, Armin; Behrendt, Andreas; Wulfmeyer, Volker; Strohbach, Jens; Förstner, Jochen; Potthast, Roland

2017-12-01

A new backscatter lidar forward operator was developed which is based on the distinct calculation of the aerosols' backscatter and extinction properties. The forward operator was adapted to the COSMO-ART ash dispersion simulation of the Eyjafjallajökull eruption in 2010. While the particle number concentration was provided as a model output variable, the scattering properties of each individual particle type were determined by dedicated scattering calculations. Sensitivity studies were performed to estimate the uncertainties related to the assumed particle properties. Scattering calculations for several types of non-spherical particles required the usage of T-matrix routines. Due to the distinct calculation of the backscatter and extinction properties of the models' volcanic ash size classes, the sensitivity studies could be made for each size class individually, which is not the case for forward models based on a fixed lidar ratio. Finally, the forward-modeled lidar profiles have been compared to automated ceilometer lidar (ACL) measurements both qualitatively and quantitatively while the attenuated backscatter coefficient was chosen as a suitable physical quantity. As the ACL measurements were not calibrated automatically, their calibration had to be performed using satellite lidar and ground-based Raman lidar measurements. A slight overestimation of the model-predicted volcanic ash number density was observed. Major requirements for future data assimilation of data from ACL have been identified, namely, the availability of calibrated lidar measurement data, a scattering database for atmospheric aerosols, a better representation and coverage of aerosols by the ash dispersion model, and more investigation in backscatter lidar forward operators which calculate the backscatter coefficient directly for each individual aerosol type. The introduced forward operator offers the flexibility to be adapted to a multitude of model systems and measurement setups.

Rice monitoring with multi-temporal and dual-polarimetric TerraSAR-X data

NASA Astrophysics Data System (ADS)

Koppe, Wolfgang; Gnyp, Martin L.; Hütt, Christoph; Yao, Yinkun; Miao, Yuxin; Chen, Xinping; Bareth, Georg

2013-04-01

This study assesses the use of TerraSAR-X data for monitoring rice cultivation in the Sanjiang Plain in Heilongjiang Province, Northeast China. The main objective is the understanding of the coherent co-polarized X-band backscattering signature of rice at different phenological stages in order to retrieve growth status. For this, multi-temporal dual polarimetric TerraSAR-X High Resolution SpotLight data (HH/VV) as well as single polarized StripMap (VV) data were acquired over the test site. In conjunction with the satellite data acquisition, a ground truth field campaign was carried out. The backscattering coefficients at HH and VV of the observed fields were extracted on the different dates and analysed as a function of rice phenology to provide a physical interpretation for the co-polarized backscatter response in a temporal and spatial manner. Then, a correlation analysis was carried out between TerraSAR-X backscattering signal and rice biomass of stem, leaf and head to evaluate the relationship with different vertical layers within the rice vegetation. HH and VV signatures show two phases of backscatter increase, one at the beginning up to 46 days after transplanting and a second one from 80 days after transplanting onwards. The first increase is related to increasing double bounce reflection from the surface-stem interaction. Then, a decreasing trend of both polarizations can be observed due to signal attenuation by increasing leaf density. A second slight increase is observed during senescence. Correlation analysis showed a significant relationship with different vertical layers at different phenological stages which prove the physical interpretation of X-band backscatter of rice. The seasonal backscatter coefficient showed that X-band is highly sensitive to changes in size, orientation and density of the dominant elements in the upper canopy.

Australian aerosol backscatter survey

NASA Technical Reports Server (NTRS)

Gras, John L.; Jones, William D.

1989-01-01

This paper describes measurements of the atmospheric backscatter coefficient in and around Australia during May and June 1986. One set of backscatter measurements was made with a CO2 lidar operating at 10.6 microns; the other set was obtained from calculations using measured aerosol parameters. Despite the two quite different data collection techniques, there is quite good agreement between the two methods. Backscatter values range from near 1 x 10 to the -8th/m per sr near the surface to 4 - 5 x 10 to the -11th/m per sr in the free troposphere at 5-7-km altitude. The values in the free troposphere are somewhat lower than those typically measured at the same height in the Northern Hemisphere.

Breast tumour visualization using 3D quantitative ultrasound methods

NASA Astrophysics Data System (ADS)

Gangeh, Mehrdad J.; Raheem, Abdul; Tadayyon, Hadi; Liu, Simon; Hadizad, Farnoosh; Czarnota, Gregory J.

2016-04-01

Breast cancer is one of the most common cancer types accounting for 29% of all cancer cases. Early detection and treatment has a crucial impact on improving the survival of affected patients. Ultrasound (US) is non-ionizing, portable, inexpensive, and real-time imaging modality for screening and quantifying breast cancer. Due to these attractive attributes, the last decade has witnessed many studies on using quantitative ultrasound (QUS) methods in tissue characterization. However, these studies have mainly been limited to 2-D QUS methods using hand-held US (HHUS) scanners. With the availability of automated breast ultrasound (ABUS) technology, this study is the first to develop 3-D QUS methods for the ABUS visualization of breast tumours. Using an ABUS system, unlike the manual 2-D HHUS device, the whole patient's breast was scanned in an automated manner. The acquired frames were subsequently examined and a region of interest (ROI) was selected in each frame where tumour was identified. Standard 2-D QUS methods were used to compute spectral and backscatter coefficient (BSC) parametric maps on the selected ROIs. Next, the computed 2-D parameters were mapped to a Cartesian 3-D space, interpolated, and rendered to provide a transparent color-coded visualization of the entire breast tumour. Such 3-D visualization can potentially be used for further analysis of the breast tumours in terms of their size and extension. Moreover, the 3-D volumetric scans can be used for tissue characterization and the categorization of breast tumours as benign or malignant by quantifying the computed parametric maps over the whole tumour volume.

Evidence of heterogeneity within bovine satellite cells isolated from young and adult animals.

PubMed

Li, J; Gonzalez, J M; Walker, D K; Hersom, M J; Ealy, A D; Johnson, S E

2011-06-01

Satellite cells are a heterogeneous population of myogenic precursors responsible for muscle growth and repair in mammals. The objectives of the experiment were to examine the growth rates and degree of heterogeneity within bovine satellite cells (BSC) isolated from young and adult animals. The BSC were harvested from the semimembranosus of young (4.3 ± 0.5 d) and adult (estimated 24 to 27 mo) cattle and cultured en masse. Young animal BSC re-enter the cell cycle sooner and reach maximal 5-ethynyl-2'-deoxyuridine (EdU) incorporation earlier (P < 0.05) than adult contemporaries. Adult BSC contain fewer (P < 0.05) MyoD and myogenin immunopositive nuclei than BSC isolated from young animals after 3, 4, and 5 d in culture. These results indicate that BSC from young animals activate, proliferate, and differentiate sooner than isolates from adult animals. Lineage heterogeneity within BSC was examined using antibodies specific for Pax7 and Myf5, lineage markers of satellite cells, and myoblasts. Immunocytochemistry revealed the majority of Pax7-expressing BSC also express Myf5; a minor population (~5%) fails to exhibit Myf5 immunoreactivity. The percentage of Pax7:Myf5 BSC from young animals decreases sooner (P < 0.05) in culture than adult BSC, indicating a more rapid rate of muscle fiber formation. A subpopulation immunopositive for Myf5 only was identified in both ages of BSC isolates. The growth kinetics and heterogeneity of young BSC was further evaluated by clonal analysis. Single cell clones were established and analyzed after 10 d. Colonies segregated into 2 groups based upon population doubling time. Immunostaining of the slow-growing colonies (population doubling time ≥ 3 d) revealed that a portion exhibited asymmetric distribution of the lineage markers Pax7 and Myf5, similar to self-renewable mouse muscle stem cells. In summary, these results offer insight into the heterogeneity of BSC and provide evidence for subtle differences between rodent and bovine myogenic precursors.

Understanding the context of balanced scorecard implementation: a hospital-based case study in pakistan

PubMed Central

2011-01-01

Background As a response to a changing operating environment, healthcare administrators are implementing modern management tools in their organizations. The balanced scorecard (BSC) is considered a viable tool in high-income countries to improve hospital performance. The BSC has not been applied to hospital settings in low-income countries nor has the context for implementation been examined. This study explored contextual perspectives in relation to BSC implementation in a Pakistani hospital. Methods Four clinical units of this hospital were involved in the BSC implementation based on their willingness to participate. Implementation included sensitization of units towards the BSC, developing specialty specific BSCs and reporting of performance based on the BSC during administrative meetings. Pettigrew and Whipp's context (why), process (how) and content (what) framework of strategic change was used to guide data collection and analysis. Data collection methods included quantitative tools (a validated culture assessment questionnaire) and qualitative approaches including key informant interviews and participant observation. Results Method triangulation provided common and contrasting results between the four units. A participatory culture, supportive leadership, financial and non-financial incentives, the presentation of clear direction by integrating support for the BSC in policies, resources, and routine activities emerged as desirable attributes for BSC implementation. The two units that lagged behind were more involved in direct inpatient care and carried a considerable clinical workload. Role clarification and consensus about the purpose and benefits of the BSC were noted as key strategies for overcoming implementation challenges in two clinical units that were relatively ahead in BSC implementation. It was noted that, rather than seeking to replace existing information systems, initiatives such as the BSC could be readily adopted if they are built on existing infrastructures and data networks. Conclusion Variable levels of the BSC implementation were observed in this study. Those intending to apply the BSC in other hospital settings need to ensure a participatory culture, clear institutional mandate, appropriate leadership support, proper reward and recognition system, and sensitization to BSC benefits. PMID:21453449

Assessing backscatter change due to backscatter gradient over the Greenland ice sheet using Envisat and SARAL altimetry

NASA Astrophysics Data System (ADS)

Su, Xiaoli; Luo, Zhicai; Zhou, Zebing

2018-06-01

Knowledge of backscatter change is important to accurately retrieve elevation change time series from satellite radar altimetry over continental ice sheets. Previously, backscatter coefficients generated in two cases, namely with and without accounting for backscatter gradient (BG), are used. However, the difference between backscatter time series obtained separately in these two cases and its impact on retrieving elevation change are not well known. Here we first compare the mean profiles of the Ku and Ka band backscatter over the Greenland ice sheet (GrIS), with results illustrating that the Ku-band backscatter is 3 ∼ 5 dB larger than that of the Ka band. We then conduct statistic analysis about time series of backscatter formed separately in the above two cases for both Ku and Ka bands over two regions in the GrIS. It is found that the standard deviation of backscatter time series becomes slightly smaller after removing the BG effect, which suggests that the method for the BG correction is effective. Furthermore, the impact on elevation change from backscatter change due to the BG effect is separately assessed for both Ku and Ka bands over the GrIS. We conclude that Ka band altimetry would benefit from a BG induced backscatter analysis (∼10% over region 2). This study may provide a reference to form backscatter time series towards refining elevation change time series from satellite radar altimetry over ice sheets using repeat-track analysis.

Structures and processes of biological soil crusts during initial ecosystem genesis of an artificial watershed in Lusatia, NE Germany

NASA Astrophysics Data System (ADS)

Spröte, Roland; Fischer, Thomas; Veste, Maik; Yair, Aaron; Wiehe, Wolfgang; Lange, Philipp; Bens, Oliver; Raab, Thomas; Hüttl, Reinhard F.

2010-05-01

The influence of biological soil crusts (BSC) in natural ecosystems on structures and processes is well investigated. In southern Brandenburg (NE Germany) it was possible to study the development of BSCs during initial ecosystem genesis on the artificial water catchment 'Hühnerwasser'. The experimental site is located in the recultivation area of the lignite open-cast mining district of southern Brandenburg (Germany). The geomorphological differentiation at the site was related to crust development, where substrate-dependent water availability defined the crust types. The mosaic-like pattern of the BSCs was associated with the distribution of fine-grained material. We defined three types if BSC: (a) initial cyanobacterial crusts (BSC-I), (b) cyanobacterial and green algae crusts on the soil surface (BSC-CG) and (c) crusts with mosses (BSC-M) between dense vegetation. The chlorophyll A content as an index for the biomass of the cryptogams increased significantly with crust type from 0.97 mg m-2 (BSC-I), 6.34 mg m-2 (BSC-CG) to 13.32 mg m-2(BSC-M). The sandy substrates with high contents of silt and clay were poorly sorted and spatially re-distributed by fluvial and aeolian processes. The contents of silt and clay were 15.9%-23.8% in the cyanobacterial crusts (BSC-I, BSC-CG) and 30.5% in the moss-crust (BSC-M). The pH values were about 7 (neutral) in all BSCs. The heighest Corg contents were found in BSC-CG (0.51%), but were not significantly lower in BSC-I (0.47%) and BSC-M (0.44%), where Corg concentrations of the original substrate ranged from 0.16 to 0.22% at construction of the catchment. The BSC types were very heterogeneously distributed and developed. Different crust types occurred in small-scale patches. Cyanobacteria which exude mucilaginous material and the rhizoids and protonemata of mosses contributed to aggregating sand grains and enhanced the topsoil stability. Furthermore, filamentous cyanobacteria and algae partially filled in the matrix pores and enmeshed sand grains, and in a wet condition extracellular polymeric substances (EPS) clogged the available pore space. Once settled, the crusts influenced the water regime of the soils. They were not pronounced hydrophobic, yet surface polarity differed between the crust types. Water infiltration was influenced by two factors: (i) the crust type, where infiltration rates were highest on almost bare substrate (BSC-I) and least when cyanobacteria and green algae formed a dense cover on the surface (BSC-CG), and (ii) the texture. Compared to BSC-CG, infiltration rates were elevated in BSC-M, pointing to decline of surface sealing when mosses penetrated the dense microphytic crust. However, the relationships among crust types, water repellency, particle size composition and infiltration are complex and need further investigation on different scales. This project is part of the Transregional Collaborative Research Centre 38 'Structures and processes of the initial ecosystem development phase in an artificial water catchment' and funded by the Deutsche Forschungsgemeinschaft.

In situ phytoplankton absorption, fluorescence emission, and particulate backscattering spectra determined from reflectance

NASA Technical Reports Server (NTRS)

Roesler, Collin S.; Pery, Mary Jane

1995-01-01

An inverse model was developed to extract the absortion and scattering (elastic and inelastic) properties of oceanic constituents from surface spectral reflectance measurements. In particular, phytoplankton spectral absorption coefficients, solar-stimulated chlorophyll a fluorescence spectra, and particle backscattering spectra were modeled. The model was tested on 35 reflectance spectra obtained from irradiance measurements in optically diverse ocean waters (0.07 to 25.35 mg/cu m range in surface chlorophyll a concentrations). The universality of the model was demonstrated by the accurate estimation of the spectral phytoplankton absorption coefficents over a range of 3 orders of magnitude (rho = 0.94 at 500 nm). Under most oceanic conditions (chlorophyll a less than 3 mg/cu m) the percent difference between measured and modeled phytoplankton absorption coefficents was less than 35%. Spectral variations in measured phytoplankton absorption spectra were well predicted by the inverse model. Modeled volume fluorescence was weakly correlated with measured chl a; fluorescence quantum yield varied from 0.008 to 0.09 as a function of environment and incident irradiance. Modeled particle backscattering coefficients were linearly related to total particle cross section over a twentyfold range in backscattering coefficents (rho = 0.996, n = 12).

Polarimetric scattering from layered media with multiple species of scatterers

NASA Technical Reports Server (NTRS)

Nghiem, S. V.; Kwok, R.; Yueh, S. H.; Kong, J. A.; Hsu, C. C.; Tassoudji, M. A.; Shin, R. T.

1995-01-01

Geophysical media are usually heterogeneous and contain multiple species of scatterers. In this paper a model is presented to calculate effective permittivities and polarimetric backscattering coefficients of multispecies-layered media. The same physical description is consistently used in the derivation of both permittivities and scattering coefficients. The strong permittivity fluctuation theory is extended to account for the multiple species of scatterers with a general ellipsoidal shape whose orientations are randomly distributed. Under the distorted Born approximation, polarimetric scattering coefficients are obtained. These calculations are applicable to the special cases of spheroidal and spherical scatterers. The model is used to study effects of scatterer shapes and multispecies mixtures on polarimetric signatures of heterogeneous media. The multispecies model accounts for moisture content in scattering media such as snowpack in an ice sheet. The results indicate a high sensitivity of backscatter to moisture with a stronger dependence for drier snow and ice grain size is important to the backscatter. For frost-covered saline ice, model results for bare ice are compared with measured data at C band and then the frost flower formation is simulated with a layer of fanlike ice crystals including brine infiltration over a rough interface. The results with the frost cover suggest a significant increase in scattering coefficients and a polarimetric signature closer to isotropic characteristics compared to the thin saline ice case.

Reviewing the application of the balanced scorecard with implications for low-income health settings.

PubMed

Rabbani, Fauziah; Jafri, S M Wasin; Abbas, Farhat; Pappas, Gregory; Brommels, Mats; Tomson, Goran

2007-01-01

High-income countries (HICs) are increasingly making use of the balanced scorecard (BSC) in healthcare. Evidence about BSC usage in low-income countries (LICs) is deficient. This study assessed feasibility of BSC use in LICs. Systematic review of electronic databases shows that the BSC improved patient, staff, clinical, and financial outcomes in HICs. To translate the experience of BSC use in HICs to their use in LICs, the applicability parameters of the National Committee for Quality Assurance were applied. Despite contextual challenges, pilot testing of BSC use can be undertaken in selected LICs. Committed leadership, cultural readiness, quality information systems, viable strategic plans, and optimum resources are required.

A comparative study of inelastic scattering models at energy levels ranging from 0.5 keV to 10 keV

NASA Astrophysics Data System (ADS)

Hu, Chia-Yu; Lin, Chun-Hung

2017-03-01

Six models, including a single-scattering model, four hybrid models, and one dielectric function model, were evaluated using Monte Carlo simulations for aluminum and copper at incident beam energies ranging from 0.5 keV to 10 keV. The inelastic mean free path, mean energy loss per unit path length, and backscattering coefficients obtained by these models are compared and discussed to understand the merits of the various models. ANOVA (analysis of variance) statistical models were used to quantify the effects of inelastic cross section and energy loss models on the basis of the simulated results deviation from the experimental data for the inelastic mean free path, the mean energy loss per unit path length, and the backscattering coefficient, as well as their correlations. This work in this study is believed to be the first application of ANOVA models towards evaluating inelastic electron beam scattering models. This approach is an improvement over the traditional approach which involves only visual estimation of the difference between the experimental data and simulated results. The data suggests that the optimization of the effective electron number per atom, binding energy, and cut-off energy of an inelastic model for different materials at different beam energies is more important than the selection of inelastic models for Monte Carlo electron scattering simulation. During the simulations, parameters in the equations should be tuned according to different materials for different beam energies rather than merely employing default parameters for an arbitrary material. Energy loss models and cross-section formulas are not the main factors influencing energy loss. Comparison of the deviation of the simulated results from the experimental data shows a significant correlation (p < 0.05) between the backscattering coefficient and energy loss per unit path length. The inclusion of backscattering electrons generated by both primary and secondary electrons for backscattering coefficient simulation is recommended for elements with high atomic numbers. In hybrid models, introducing the inner shell ionization model improves the accuracy of simulated results.

Clinicopahological features of superficial basaloid squamous cell carcinoma of the esophagus.

PubMed

Oguma, J; Ozawa, S; Kazuno, A; Nitta, M; Ninomiya, Y; Tomita, S

2017-12-01

Basaloid squamous cell carcinoma (BSC) of the esophagus is classified as an epithelial malignant tumor and is a rare variant of squamous cell carcinoma (SCC). Most previous reports have suggested that advanced BSC has a poorer prognosis than typical SCC because of its high biological malignancy, but the biological activity of superficial BSC remains unclear. Twenty cases of superficial BSC, which underwent surgical resection in Tokai University Hospital between January 2004 and December 2013, were analyzed retrospectively. Among these cases, 19 cases with a T1 depth of invasion (BSC group) were compared with 180 cases of SCC that were resected during the same period and were pathologically diagnosed as T1 (SCC group). The frequency of lymph node metastasis in the T1 BSC group was significantly lower (2 patients, 11%) than that in the SCC group (84 patients, 47%) (P = 0.005). The frequency of lymphatic invasion in the BSC group was also lower (9 patients, 47%) than that in the SCC group (131 patients, 73%) (P = 0.021). The pathological type of the metastatic lymph node was BSC in all the superficial BSC cases with lymph node metastasis. This study demonstrated that lymph node metastasis was less likely to occur in cases with superficial BSC than in cases with superficial SCC. © The Authors 2017. Published by Oxford University Press on behalf of International Society for Diseases of the Esophagus. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Phase III trial of vinflunine plus best supportive care compared with best supportive care alone after a platinum-containing regimen in patients with advanced transitional cell carcinoma of the urothelial tract.

PubMed

Bellmunt, Joaquim; Théodore, Christine; Demkov, Tomasz; Komyakov, Boris; Sengelov, Lisa; Daugaard, Gedske; Caty, Armelle; Carles, Joan; Jagiello-Gruszfeld, Agnieszka; Karyakin, Oleg; Delgado, François-Michel; Hurteloup, Patrick; Winquist, Eric; Morsli, Nassim; Salhi, Yacine; Culine, Stéphane; von der Maase, Hans

2009-09-20

Vinflunine (VFL) is a new microtubule inhibitor that has activity against transitional cell carcinoma of urothelial tract (TCCU). We conducted a randomized phase III study of VFL and best supportive care (BSC) versus BSC alone in the treatment of patients with advanced TCCU who had experienced progression after a first-line platinum-containing regimen. The study was designed to compare overall survival (OS) between patients receiving VFL + BSC (performance status [PS] = 0: 320 mg/m(2), every 3 weeks; PS = 0 with previous pelvic radiation and PS = 1: 280 mg/m(2) subsequently escalated to 320 mg/m(2)) or BSC. Three hundred seventy patients were randomly assigned (VFL + BSC, n =253; BSC, n = 117). Both arms were well balanced except there were more patients with PS more than 1 (10% difference) in the BSC arm. Main grade 3 or 4 toxicities for VFL + BSC were neutropenia (50%), febrile neutropenia (6%), anemia (19%), fatigue (19%), and constipation (16%). In the intent-to-treat population, the objective of a median 2-month survival advantage (6.9 months for VFL + BSC v 4.6 months for BSC) was achieved (hazard ratio [HR] = 0.88; 95% CI, 0.69 to 1.12) but was not statistically significant (P = .287). Multivariate Cox analysis adjusting for prognostic factors showed statistically significant effect of VFL on OS (P = .036), reducing the death risk by 23% (HR = 0.77; 95% CI, 0.61 to 0.98). In the eligible population (n = 357), the median OS was significantly longer for VFL + BSC than BSC (6.9 v 4.3 months, respectively), with the difference being statistically significant (P = .040). Overall response rate, disease control, and progression-free survival were all statistically significant favoring VFL + BSC (P = .006, P = .002, and P = .001, respectively). VFL demonstrates a survival advantage in second-line treatment for advanced TCCU. Consistency of results exists with significant and meaningful benefit over all efficacy parameters. Safety profile is acceptable, and therefore, VFL seems to be a reasonable option for TCCU progressing after first-line platinum-based therapy.

Advances in atmospheric temperature profile measurements using high spectral resolution lidar

NASA Astrophysics Data System (ADS)

Razenkov, Ilya I.; Eloranta, Edwin W.

2018-04-01

This paper reports the atmospheric temperature profile measurements using a University of Wisconsin-Madison High Spectral Resolution Lidar (HSRL) and describes improvements in the instrument performance. HSRL discriminates between Mie and Rayleigh backscattering [1]. Thermal motion of molecules broadens the spectrum of the transmitted laser light due to Doppler effect. The HSRL exploits this property to allow the absolute calibration of the lidar and measurements of the aerosol volume backscatter coefficient. Two iodine absorption filters with different line widths are used to resolve temperature sensitive changes in Rayleigh backscattering for atmospheric temperature profile measurements.

LASER APPLICATIONS AND OTHER TOPICS IN QUANTUM ELECTRONICS: On the aerosol backscattering coefficient in atmosphere in the spectral range 9-13.5μm

NASA Astrophysics Data System (ADS)

Vasil'ev, B. I.; Mannoun, Oussama

2007-05-01

The aerosol backscattering coefficient βπ in a surface atmospheric layer is calculated at the emission lines of NH3 and CO2 lasers (9-13.5 μm). It is shown that the coefficients βπ at the emission lines of an NH3 laser (11-13.5 μm) are comparable with the coefficients βπ at the emission lines of a CO2 laser near 10.6 μm. The dependence of βπ on the humidity and type of aerosols is studied. It is also shown that the coefficient βπ in a surface atmospheric layer at the lasing of an NH3 laser varies from 10-10 to 7×10-9 cm-1 sr-1. The lidar aerosol ratio is calculated as a function of the mean aerosol radius. It is found that this ratio is independent of the particle size for aerosol particles of radius exceeding 40 μm for the 11.7-μm aP(4,0) line of the ammonia laser.

Using the balanced scorecard to measure Chinese and Japanese hospital performance.

PubMed

Chen, Xiao-yun; Yamauchi, Kazunobu; Kato, Ken; Nishimura, Akio; Ito, Katuski

2006-01-01

The objective of the paper is to confirm the feasibility and value of using the balanced scorecard (BSC) to measure performance in two hospitals in different countries. One hospital from China and another from Japan were chosen and key indicators were selected according to the BSC framework. A comparative hospital performance measurement model was set up using the BSC framework to comprehensively compare hospital performance in two countries. The BSC was found to be effective for underlining existing problems and identifying opportunities for improvements. The BSC also revealed the hospitals' contribution to performance improvement of each country's total health system. Hospital performance comparisons between countries using the BSC depend on the selection of feasible and appropriate key performance indicators, which is occasionally limited by data collection problems. The first use of the BSC to compare hospital performance between China and Japan shows benefits that not only suggests performance improvements in individual hospitals but also reveals effective health factors allowing implementation of valid national health policies.

Estimation of Physical Parameters of a Multilayered Multi-Scale Vegetated Surface

NASA Astrophysics Data System (ADS)

Hosni, I.; Bennaceur Farah, L.; Naceur, M. S.; Farah, I. R.

2016-06-01

Soil moisture is important to enable the growth of vegetation in the way that it also conditions the development of plant population. Additionally, its assessment is important in hydrology and agronomy, and is a warning parameter for desertification. Furthermore, the soil moisture content affects exchanges with the atmosphere via the energy balance at the soil surface; it is significant due to its impact on soil evaporation and transpiration. Therefore, it conditions the energy transfer between Earth and atmosphere. Many remote sensing methods were tested. For the soil moisture; the first methods relied on the optical domain (short wavelengths). Obviously, due to atmospheric effects and the presence of clouds and vegetation cover, this approach is doomed to fail in most cases. Therefore, the presence of vegetation canopy complicates the retrieval of soil moisture because the canopy contains moisture of its own. This paper presents a synergistic methodology of SAR and optical remote sensing data, and it's for simulation of statistical parameters of soil from C-band radar measurements. Vegetation coverage, which can be easily estimated from optical data, was combined in the backscattering model. The total backscattering was divided into the amount attributed to areas covered with vegetation and that attributed to areas of bare soil. Backscattering coefficients were simulated using the established backscattering model. A two-dimensional multiscale SPM model has been employed to investigate the problem of electromagnetic scattering from an underlying soil. The water cloud model (WCM) is used to account for the effect of vegetation water content on radar backscatter data, whereof to eliminate the impact of vegetation layer and isolate the contributions of vegetation scattering and absorption from the total backscattering coefficient.

Lipschitz stability for an inverse hyperbolic problem of determining two coefficients by a finite number of observations

NASA Astrophysics Data System (ADS)

Beilina, L.; Cristofol, M.; Li, S.; Yamamoto, M.

2018-01-01

We consider an inverse problem of reconstructing two spatially varying coefficients in an acoustic equation of hyperbolic type using interior data of solutions with suitable choices of initial condition. Using a Carleman estimate, we prove Lipschitz stability estimates which ensure unique reconstruction of both coefficients. Our theoretical results are justified by numerical studies on the reconstruction of two unknown coefficients using noisy backscattered data.

Active and passive microwave measurements of soil moisture in FIFE

NASA Technical Reports Server (NTRS)

Wang, J. R.; Gogineni, S. P.; Ampe, J.

1992-01-01

During the intensive field campaigns of the First International Satellite Land Surface Climatology Project (ISLSCP) Field Experiment (FIFE) in May-October of 1987, several nearly simultaneous measurements were made with low-altitude flights of the L-band radiometer and C- and X-band scatterometers over two transects in the Konza Prairie Natural Research Area, some 8 km south of Manhattan, Kansas. These measurements showed that although the scatterometers were sensitive to soil moisture variations in most regions under the flight path, the L-band radiometer lost most of its sensitivity in regions unburned for many years. The correlation coefficient derived from the regression between the radar backscattering coefficient and the soil moisture was found to improve with the increase in antenna incidence angle. This is attributed to a steeper falloff of the backscattering coefficient as a function of local incidence at angles near nadir than at angles greater than 30 deg.

Measured backscatter and attenuation properties, including polarization effects, of various dispersions at 0.9 micron

NASA Technical Reports Server (NTRS)

Kohl, R. H.; Flaherty, M. I.; Partin, R. L.

1977-01-01

The optical properties of a wide variety of atmospheric dispersions were studied using a 0.9-micron lidar system which included a GaAs laser stack transmitter emitting a horizontally polarized beam of 4 milliradians vertical divergence and 1.5 milliradians horizontal divergence. A principal means for assessing optical properties was the polarization ratio, that is, the backscattered radiation power perpendicular to the transmitter beam divided by the backscattered radiation power parallel to the beam polarization. The ratio of the backscattered fraction to the attenuation coefficient was also determined. Data on the dispersion properties of black carbon smoke, road dust, fog, fair-weather cumulus clouds, snow and rain were obtained; the adverse effects of sunlight-induced background noise on the readings is also discussed.

What constitutes best supportive care in the treatment of advanced non-small cell lung cancer patients?--Results from the lung cancer economics and outcomes research (LUCEOR) study.

PubMed

Lester, J F; Agulnik, J; Akerborg, O; Chouaid, C; De Geer, A; Finnern, H W; Herder, G J M; Lungershausen, J; Mitchell, P L R; Vansteenkiste, J; Ziske, C; Goker, E

2013-10-01

A significant proportion of advanced non-small cell lung cancer (NSCLC) patients receive supportive treatments to manage disease-related symptoms either separately or combined with systemic anti-cancer therapy (SACT). This supportive treatment is commonly referred to as best supportive care (BSC). Definition of BSC in clinical trials and its description in published comparative and real-life NSCLC studies is limited. The lack of a consensus BSC definition makes detailed evaluations of clinical trials and comparisons between clinical trials problematic. Data were collected as part of the lung cancer economics and outcomes research (LUCEOR) study. Information on treatment and treatment outcomes from deceased stage IIIb/IV NSCLC patients across ten countries was retrospectively collected from medical records. BSC was defined as the best care available as judged by the attending physicians. A total of 1327 patients' data were analyzed. Of those, 774/1327 (58%), 316/631 (50%), 123/259 (47%), 25/56 (45%) and 15/26 (58%) were administered treatment defined as BSC with first, second, third, fourth and fifth-line SACT respectively. In total, 346/678 (51%), 149/335 (45%), 86/176 (49%), 11/28 (39%) and 13/25 (52%) of patients were administered treatment defined as BSC in the end-of-life setting after finishing first, second, third, fourth and fifth-line SACT respectively. BSC therapies could be grouped into 24 different categories. The most common elements did not vary substantially whether given with SACT (irrespective of treatment line), in the end-of-life setting, or between countries. The commonest categories of BSC were narcotic and non-narcotic analgesics, corticosteroids and gastrointestinal medication. There were no major differences in what constituted BSC. BSC included in all instances narcotic and non-narcotic analgesics, corticosteroids and gastrointestinal medication. To our knowledge this is the first study attempting to describe BSC in routine clinical practice. This study's results could help define a practical, up to date, evidence-based definition of BSC. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Comparison of high intensity focused ultrasound (HIFU) exposures using empirical and backscatter attenuation estimation methods

NASA Astrophysics Data System (ADS)

Civale, John; Ter Haar, Gail; Rivens, Ian; Bamber, Jeff

2005-09-01

Currently, the intensity to be used in our clinical HIFU treatments is calculated from the acoustic path lengths in different tissues measured on diagnostic ultrasound images of the patient in the treatment position, and published values of ultrasound attenuation coefficients. This yields an approximate value for the acoustic power at the transducer required to give a stipulated focal intensity in situ. Estimation methods for the actual acoustic attenuation have been investigated in large parts of the tissue path overlying the target volume from the backscattered ultrasound signal for each patient (backscatter attenuation estimation: BAE). Several methods have been investigated. The backscattered echo information acquired from an Acuson scanner has been used to compute the diffraction-corrected attenuation coefficient at each frequency using two methods: a substitution method and an inverse diffraction filtering process. A homogeneous sponge phantom was used to validate the techniques. The use of BAE to determine the correct HIFU exposure parameters for lesioning has been tested in ex vivo liver. HIFU lesions created with a 1.7-MHz therapy transducer have been studied using a semiautomated image processing technique. The reproducibility of lesion size for given in situ intensities determined using BAE and empirical techniques has been compared.

Analysis of the Spectral Backscattering Coefficient Variability on the Northeastern shelf of the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Gallegos, S. C.; Gould, R. W.; Arnone, R. A.; Teague, W. J.; Mitchell, D. A.; Ko, D.

2005-05-01

The continental shelf of the northeastern Gulf of Mexico between 87.5 W and 88.5 W is an ideal place to study coastal processes. In this region, the shelf slopes gently down to depths of 100 m, and then increases rapidly to depths greater than a mile. The Naval Research Laboratory at Stennis Space Center in Mississippi is currently undertaking an intensive measurement and modeling program to determine the cross-shelf exchange processes and their relation to the optical parameters of this area. In this study, we report our efforts to quantify the variability of the spectral backscattering coefficient derived from SeaWiFS imagery via empirical orthogonal functions. We compare the most relevant modes with the spatial distribution of Eddy Kinetic Energy (EKE) computed by the Inter Americas Seas (IAS) model and in-situ measurements by acoustic Doppler current profilers deployed between May 2004 and May 2005. The results indicate that most of the backscattering variability is contained in areas north of 29.2N which coincides with the edge of the continental shelf (100 m depth). Sporadic increases in backscattering are observed as far south as 29.0 N and to the east of 88.1W. These increases can be explained by fluctuations in surface EKE.

Suspended sediment assessment by combining sound attenuation and backscatter measurements - analytical method and experimental validation

NASA Astrophysics Data System (ADS)

Guerrero, Massimo; Di Federico, Vittorio

2018-03-01

The use of acoustic techniques has become common for estimating suspended sediment in water environments. An emitted beam propagates into water producing backscatter and attenuation, which depend on scattering particles concentration and size distribution. Unfortunately, the actual particles size distribution (PSD) may largely affect the accuracy of concentration quantification through the unknown coefficients of backscattering strength, ks2, and normalized attenuation, ζs. This issue was partially solved by applying the multi-frequency approach. Despite this possibility, a relevant scientific and practical question remains regarding the possibility of using acoustic methods to investigate poorly sorted sediment in the spectrum ranging from clay to fine sand. The aim of this study is to investigate the possibility of combining the measurement of sound attenuation and backscatter to determine ζs for the suspended particles and the corresponding concentration. The proposed method is moderately dependent from actual PSD, thus relaxing the need of frequent calibrations to account for changes in ks2 and ζs coefficients. Laboratory tests were conducted under controlled conditions to validate this measurement technique. With respect to existing approaches, the developed method more accurately estimates the concentration of suspended particles ranging from clay to fine sand and, at the same time, gives an indication on their actual PSD.

Recovery of biological soil crust richness and cover 12-16 years after wildfires in Idaho, USA

NASA Astrophysics Data System (ADS)

Root, Heather T.; Brinda, John C.; Dodson, E. Kyle

2017-09-01

Changing fire regimes in western North America may impact biological soil crust (BSC) communities that influence many ecosystem functions, such as soil stability and C and N cycling. However, longer-term effects of wildfire on BSC abundance, species richness, functional groups, and ecosystem functions after wildfire (i.e., BSC resilience) are still poorly understood. We sampled BSC lichen and bryophyte communities at four sites in Idaho, USA, within foothill steppe communities that included wildfires from 12 to 16 years old. We established six plots outside each burn perimeter and compared them with six plots of varying severity within each fire perimeter at each site. BSC cover was most strongly negatively impacted by wildfire at sites that had well-developed BSC communities in adjacent unburned plots. BSC species richness was estimated to be 65 % greater in unburned plots compared with burned plots, and fire effects did not vary among sites. In contrast, there was no evidence that vascular plant functional groups or fire severity (as measured by satellite metrics differenced normalized burn ratio (dNBR) or relativized differenced normalized burn ratio (RdNBR)) significantly affected longer-term BSC responses. Three large-statured BSC functional groups that may be important in controlling wind and water erosion (squamulose lichens, vagrant lichens, and tall turf mosses) exhibited a significant decrease in abundance in burned areas relative to adjacent unburned areas. The decreases in BSC cover and richness along with decreased abundance of several functional groups suggest that wildfire can negatively impact ecosystem function in these semiarid ecosystems for at least 1 to 2 decades. This is a concern given that increased fire frequency is predicted for the region due to exotic grass invasion and climate change.

Intercomparison of Pulsed Lidar Data with Flight Level CW Lidar Data and Modeled Backscatter from Measured Aerosol Microphysics Near Japan and Hawaii

NASA Technical Reports Server (NTRS)

Cutten, D. R.; Spinhirne, J. D.; Menzies, R. T.; Bowdle, D. A.; Srivastava, V.; Pueschel, R. F.; Clarke, A. D.; Rothermel, J.

1998-01-01

Aerosol backscatter coefficient data were examined from two nights near Japan and Hawaii undertaken during NASA's Global Backscatter Experiment (GLOBE) in May-June 1990. During each of these two nights the aircraft traversed different altitudes within a region of the atmosphere defined by the same set of latitude and longitude coordinates. This provided an ideal opportunity to allow flight level focused continuous wave (CW) lidar backscatter measured at 9.11-micron wavelength and modeled aerosol backscatter from two aerosol optical counters to be compared with pulsed lidar aerosol backscatter data at 1.06- and 9.25-micron wavelengths. The best agreement between all sensors was found in the altitude region below 7 km, where backscatter values were moderately high at all three wavelengths. Above this altitude the pulsed lidar backscatter data at 1.06- and 9.25-micron wavelengths were higher than the flight level data obtained from the CW lidar or derived from the optical counters, suggesting sample volume effects were responsible for this. Aerosol microphysics analysis of data near Japan revealed a strong sea-salt aerosol plume extending upward from the marine boundary layer. On the basis of sample volume differences, it was found that large particles were of different composition compared with the small particles for low backscatter conditions.

Development of an infrared analyzer following the

NASA Technical Reports Server (NTRS)

1976-01-01

A radar calibration subsystem for measuring the radar backscattering characteristics of an imaged terrain is described. To achieve the required accuracy for the backscattering coefficient measurement (about 2 dB with 80 percent confidence), the space hardware design includes a means of monitoring the state parameters of the radar. For example, the transmitter output power is sampled and a replica of its output waveform is circulated through the receiver. These are recorded digitally and are used on the ground to determine such radar parameters as the transmitter power and the receiver gain. This part of the data is needed by the ground processor to measure the terrain backscattering characteristics.

Estimation of chromophoric dissolved organic matter in the Mississippi and Atchafalaya river plume regions using above-surface hyperspectral remote sensing

NASA Astrophysics Data System (ADS)

Zhu, Weining; Yu, Qian; Tian, Yong Q.; Chen, Robert F.; Gardner, G. Bernard

2011-02-01

A method for the inversion of hyperspectral remote sensing was developed to determine the absorption coefficient for chromophoric dissolved organic matter (CDOM) in the Mississippi and Atchafalaya river plume regions and the northern Gulf of Mexico, where water types vary from Case 1 to turbid Case 2. Above-surface hyperspectral remote sensing data were measured by a ship-mounted spectroradiometer and then used to estimate CDOM. Simultaneously, water absorption and attenuation coefficients, CDOM and chlorophyll fluorescence, turbidities, and other related water properties were also measured at very high resolution (0.5-2 m) using in situ, underwater, and flow-through (shipboard, pumped) optical sensors. We separate ag, the absorption coefficient a of CDOM, from adg (a of CDOM and nonalgal particles) based on two absorption-backscattering relationships. The first is between ad (a of nonalgal particles) and bbp (total particulate backscattering coefficient), and the second is between ap (a of total particles) and bbp. These two relationships are referred as ad-based and ap-based methods, respectively. Consequently, based on Lee's quasi-analytical algorithm (QAA), we developed the so-called Extended Quasi-Analytical Algorithm (QAA-E) to decompose adg, using both ad-based and ap-based methods. The absorption-backscattering relationships and the QAA-E were tested using synthetic and in situ data from the International Ocean-Colour Coordinating Group (IOCCG) as well as our own field data. The results indicate the ad-based method is relatively better than the ap-based method. The accuracy of CDOM estimation is significantly improved by separating ag from adg (R2 = 0.81 and 0.65 for synthetic and in situ data, respectively). The sensitivities of the newly introduced coefficients were also analyzed to ensure QAA-E is robust.

Evaluating the balanced scorecard at the University Health Network: an impact assessment.

PubMed

Young, Justin; Bell, Robert; Khalfan, Adil; Lindquist, Evert

2008-01-01

The balanced scorecard (BSC) has become increasing popular in healthcare organizations. A recent study conducted at the University Health Network in Toronto explored the extent to which the BSC has focused and aligned various organizational units and departments around shared goals and objectives. The evaluation also assessed the BSC's impact on front-line staff and how the development and rollout of the BSC should be modified in the next planning iteration.

Meeting the challenge in performance management: the diffusion and implementation of the balanced scorecard in Chinese hospitals.

PubMed

Gao, Tian; Gurd, Bruce

2015-03-01

The bonus system used in Chinese hospitals has been criticized for eroding doctors' professional ethics and aggravating patient expense. This research article focuses on one system to improve hospital performance, the balanced scorecard (BSC). We use three data sources to examine the diffusion and implementation of the BSC in China: a questionnaire survey in Shandong Province, a print-media indicators and content analysis of the published BSC papers and semi-structured interviews with managers of Chinese hospitals that use the BSC. The research evidence shows that bonus systems are important, partially because of the poor pay of hospital professionals, and the BSC is perceived as providing a fair system to award such bonuses. This helps explain the relative endurance of the BSC in Chinese hospitals. Published by Oxford University Press in association with The London School of Hygiene and Tropical Medicine © The Author 2014; all rights reserved.

Light backscattering efficiency and related properties of some phytoplankters

NASA Astrophysics Data System (ADS)

Ahn, Yu-Hwan; Bricaud, Annick; Morel, André

1992-11-01

By using a set-up that combines an integrating sphere with a spectroradiometer LI-1800 UW, the backscattering properties of nine different phytoplankters grown in culture have been determined experimentally for the wavelengths domain ν = 400 up to 850 nm. Simultaneously, the absorption and attenuation properties, as well as the size distribution function, have been measured. This set of measurements allowed the spectral values of refractive index, and subsequently the volume scattering functions (VSF) of the cells, to be derived, by operating a scattering model previously developed for spherical and homogeneous cells. The backscattering properties, measured within a restricted angular domain (approximately between 132 and 174°), have been compared to theoretical predictions. Although there appear some discrepancies between experimental and predicted values (probably due to experimental errors as well as deviations of actual cells from computational hypotheses), the overall agreement is good; in particular the observed interspecific variations of backscattering values, as well as the backscattering spectral variation typical of each species, are well accounted for by theory. Using the computed VSF, the measured backscattering properties can be converted (assuming spherical and homogeneous cells) into efficiency factors for backscattering ( overlineQbb) . Thhe spectral behavior of overlineQbb appears to be radically different from that for total scattering overlineQb. For small cells, overlineQ (λ) is practically constant over the spectrum, whereas overlineQb(λ) varies approximately according to a power law (λ -2). As the cell size increases, overlineQbb conversely, becomes increasingly featured, whilst overlineQb becomes spectrally flat. The chlorophyll-specific backscattering coefficients ( b b∗ appear highly variable and span nearly two orders of magnitude. The chlorophyll-specific absorption and scattering coefficients, a ∗ and b ∗, are mainly ruled by the interspecific variations in cellssize ( D) and intracellular pigment concentration ( Ci) (actually by the variations of the product DCi). Though b b∗ is involved in the modelling of the diffuse reflectance of waters, the impact of its actual variation is greatly limited because typical b b∗ values, even at their maximum (10 -3 m 2 mg -1), are very low. This result confirms that living algae have a negligible influence on the backscattering process by oceanic waters; other particles (bacteria, detritus, etc.) associated with algae are mainly responsible for this process.

Applications of the balanced scorecard for strategic management and performance measurement in the health sector.

PubMed

Behrouzi, Farshad; Shaharoun, Awaluddin Mohamed; Ma'aram, Azanizawati

2014-05-01

In order to attain a useful balanced scorecard (BSC), appropriate performance perspectives and indicators are crucial to reflect all strategies of the organisation. The objectives of this survey were to give an insight regarding the situation of the BSC in the health sector over the past decade, and to afford a generic approach of the BSC development for health settings with specific focus on performance perspectives, performance indicators and BSC generation. After an extensive search based on publication date and research content, 29 articles published since 2002 were identified, categorised and analysed. Four critical attributes of each article were analysed, including BSC generation, performance perspectives, performance indicators and auxiliary tools. The results showed that 'internal business process' was the most notable BSC perspective as it was included in all reviewed articles. After investigating the literature, it was concluded that its comprehensiveness is the reason for the importance and high usage of this perspective. The findings showed that 12 cases out of 29 reviewed articles (41%) exceeded the maximum number of key performance indicators (KPI) suggested in a previous study. It was found that all 12 cases were large organisations with numerous departments (e.g. national health organisations). Such organisations require numerous KPI to cover all of their strategic objectives. It was recommended to utilise the cascaded BSC within such organisations to avoid complexity and difficulty in gathering, analysing and interpreting performance data. Meanwhile it requires more medical staff to contribute in BSC development, which will result in greater reliability of the BSC.

Development and implementation of a balanced scorecard in an academic hospitalist group.

PubMed

Hwa, Michael; Sharpe, Bradley A; Wachter, Robert M

2013-03-01

Academic hospitalist groups (AHGs) are often expected to excel in multiple domains: quality improvement, patient safety, education, research, administration, and clinical care. To be successful, AHGs must develop strategies to balance their energies, resources, and performance. The balanced scorecard (BSC) is a strategic management system that enables organizations to translate their mission and vision into specific objectives and metrics across multiple domains. To date, no hospitalist group has reported on BSC implementation. We set out to develop a BSC as part of a strategic planning initiative. Based on a needs assessment of the University of California, San Francisco, Division of Hospital Medicine, mission and vision statements were developed. We engaged representative faculty to develop strategic objectives and determine performance metrics across 4 BSC perspectives. There were 41 metrics identified, and 16 were chosen for the initial BSC. It allowed us to achieve several goals: 1) present a broad view of performance, 2) create transparency and accountability, 3) communicate goals and engage faculty, and 4) ensure we use data to guide strategic decisions. Several lessons were learned, including the need to build faculty consensus, establish metrics with reliable measureable data, and the power of the BSC to drive goals across the division. We successfully developed and implemented a BSC in an AHG as part of a strategic planning initiative. The BSC has been instrumental in allowing us to achieve balanced success in multiple domains. Academic groups should consider employing the BSC as it allows for a data-driven strategic planning and assessment process. Copyright © 2013 Society of Hospital Medicine.

Skeletal dosimetry for external exposure to photons based on µCT images of spongiosa from different bone sites

NASA Astrophysics Data System (ADS)

Kramer, R.; Khoury, H. J.; Vieira, J. W.; Kawrakow, I.

2007-11-01

Micro computed tomography (µCT) images of human spongiosa have recently been used for skeletal dosimetry with respect to external exposure to photon radiation. In this previous investigation, the calculation of equivalent dose to the red bone marrow (RBM) and to the bone surface cells (BSC) was based on five different clusters of micro matrices derived from µCT images of vertebrae, and the BSC equivalent dose for 10 µm thickness of the BSC layer was determined using an extrapolation method. The purpose of this study is to extend the earlier investigation by using µCT images from eight different bone sites and by introducing an algorithm for the direct calculation of the BSC equivalent dose with sub-micro voxel resolution. The results show that for given trabecular bone volume fractions (TBVFs) the whole-body RBM equivalent dose does not depend on bone site-specific properties or imaging parameters. However, this study demonstrates that apart from the TBVF and the BSC layer thickness, the BSC equivalent dose additionally depends on a so-called trabecular bone structure (TBS) effect, i.e. that the contribution of photo-electrons released in trabecular bone to the BSC equivalent dose also depends on the bone site-specific structure of the trabeculae. For a given bone site, the TBS effect is also a function of the thickness of the BSC layer, and it could be shown that this effect would disappear almost completely, should the BSC layer thickness be raised from 10 to 50 µm, according to new radiobiological findings.

Verification studies of Seasat-A satellite scatterometer /SASS/ measurements

NASA Technical Reports Server (NTRS)

Halberstam, I.

1981-01-01

Two comparisons between Seasat-A satellite scatterometer (SASS) data and surface truth, obtained from the Gulf of Alaska Seasat Experiment and the Joint Air-Sea Interaction program, have been made to determine the behavior of SASS and its algorithms. The performance of SASS was first evaluated irrespective of the algorithms employed to convert the SASS data to geophysical parameters, which was done by separating the backscatter measurements into small bins of incidence and azimuth angles and polarity and regression against wind speed measurements. The algorithms were then tested by comparing their predicted slopes and y intercepts with those derived from the regressions, and by comparing each SASS backscatter measurement with the backscatter derived from the algorithms, and the given wind velocity from the observations. It was shown that SASS was insensitive to winds at high incidence angles for horizontal polarizations. Fairly high correlations were found between backscatter and wind speeds. The algorithms functioned well at mid-ranges of incidence angle and backscattering coefficient.

Circularly polarized measurements of radar backscatter from terrain

NASA Astrophysics Data System (ADS)

Wilson, E. A.; Brunfeldt, D. R.; Ulaby, F. T.; Holtzman, J. C.

1980-02-01

This report documents the design changes to the University of Kansas MAS 8-18/35 scatterometer system required to incorporate a circular polarization capability and a subsequent backscatter measurement program. The modifications enable the MAS 8-18/35 system to acquire both linear (HH, HV, VV) and circular (RR, RL, LL) radar backscatter data over its entire operating range of 8-18 GHz and 35 GHz. The measurement program described herein consisted of measurements of the backscatter coefficient, as a function of the angle of incidence (0-80) at selected frequencies in the 8-18 GHz range using circular polarization. Targets studied included coniferous and deciduous trees, wet and dry asphalt and concrete and bare and plowed ground at various moisture conditions. Coniferous and deciduous tree measurements were taken in both August and November so that seasonal changes could be observed.

Modeling Surface Roughness to Estimate Surface Moisture Using Radarsat-2 Quad Polarimetric SAR Data

NASA Astrophysics Data System (ADS)

Nurtyawan, R.; Saepuloh, A.; Budiharto, A.; Wikantika, K.

2016-08-01

Microwave backscattering from the earth's surface depends on several parameters such as surface roughness and dielectric constant of surface materials. The two parameters related to water content and porosity are crucial for estimating soil moisture. The soil moisture is an important parameter for ecological study and also a factor to maintain energy balance of land surface and atmosphere. Direct roughness measurements to a large area require extra time and cost. Heterogeneity roughness scale for some applications such as hydrology, climate, and ecology is a problem which could lead to inaccuracies of modeling. In this study, we modeled surface roughness using Radasat-2 quad Polarimetric Synthetic Aperture Radar (PolSAR) data. The statistical approaches to field roughness measurements were used to generate an appropriate roughness model. This modeling uses a physical SAR approach to predicts radar backscattering coefficient in the parameter of radar configuration (wavelength, polarization, and incidence angle) and soil parameters (surface roughness and dielectric constant). Surface roughness value is calculated using a modified Campbell and Shepard model in 1996. The modification was applied by incorporating the backscattering coefficient (σ°) of quad polarization HH, HV and VV. To obtain empirical surface roughness model from SAR backscattering intensity, we used forty-five sample points from field roughness measurements. We selected paddy field in Indramayu district, West Java, Indonesia as the study area. This area was selected due to intensive decreasing of rice productivity in the Northern Coast region of West Java. Third degree polynomial is the most suitable data fitting with coefficient of determination R2 and RMSE are about 0.82 and 1.18 cm, respectively. Therefore, this model is used as basis to generate the map of surface roughness.

Ocean Lidar Measurements of Beam Attenuation and a Roadmap to Accurate Phytoplankton Biomass Estimates

NASA Astrophysics Data System (ADS)

Hu, Yongxiang; Behrenfeld, Mike; Hostetler, Chris; Pelon, Jacques; Trepte, Charles; Hair, John; Slade, Wayne; Cetinic, Ivona; Vaughan, Mark; Lu, Xiaomei; Zhai, Pengwang; Weimer, Carl; Winker, David; Verhappen, Carolus C.; Butler, Carolyn; Liu, Zhaoyan; Hunt, Bill; Omar, Ali; Rodier, Sharon; Lifermann, Anne; Josset, Damien; Hou, Weilin; MacDonnell, David; Rhew, Ray

2016-06-01

Beam attenuation coefficient, c, provides an important optical index of plankton standing stocks, such as phytoplankton biomass and total particulate carbon concentration. Unfortunately, c has proven difficult to quantify through remote sensing. Here, we introduce an innovative approach for estimating c using lidar depolarization measurements and diffuse attenuation coefficients from ocean color products or lidar measurements of Brillouin scattering. The new approach is based on a theoretical formula established from Monte Carlo simulations that links the depolarization ratio of sea water to the ratio of diffuse attenuation Kd and beam attenuation C (i.e., a multiple scattering factor). On July 17, 2014, the CALIPSO satellite was tilted 30° off-nadir for one nighttime orbit in order to minimize ocean surface backscatter and demonstrate the lidar ocean subsurface measurement concept from space. Depolarization ratios of ocean subsurface backscatter are measured accurately. Beam attenuation coefficients computed from the depolarization ratio measurements compare well with empirical estimates from ocean color measurements. We further verify the beam attenuation coefficient retrievals using aircraft-based high spectral resolution lidar (HSRL) data that are collocated with in-water optical measurements.

An Innovative Concept for Spacebased Lidar Measurement of Ocean Carbon Biomass

NASA Technical Reports Server (NTRS)

Hu, Yongxiang; Behrenfeld, Michael; Hostetler, Chris; Pelon, Jacques; Trepte, Charles; Hair, John; Slade, Wayne; Cetinic, Ivona; Vaughan, Mark; Lu, Xiaomei;

Retrieval of atmospheric backscatter and extinction profiles with the aladin airborne demonstrator (A2D)

NASA Astrophysics Data System (ADS)

Geiss, Alexander; Marksteiner, Uwe; Lux, Oliver; Lemmerz, Christian; Reitebuch, Oliver; Kanitz, Thomas; Straume-Lindner, Anne Grete

2018-04-01

By the end of 2017, the European Space Agency (ESA) will launch the Atmospheric laser Doppler instrument (ALADIN), a direct detection Doppler wind lidar operating at 355 nm. An important tool for the validation and optimization of ALADIN's hardware and data processors for wind retrievals with real atmospheric signals is the ALADIN airborne demonstrator A2D. In order to be able to validate and test aerosol retrieval algorithms from ALADIN, an algorithm for the retrieval of atmospheric backscatter and extinction profiles from A2D is necessary. The A2D is utilizing a direct detection scheme by using a dual Fabry-Pérot interferometer to measure molecular Rayleigh signals and a Fizeau interferometer to measure aerosol Mie returns. Signals are captured by accumulation charge coupled devices (ACCD). These specifications make different steps in the signal preprocessing necessary. In this paper, the required steps to retrieve aerosol optical products, i. e. particle backscatter coefficient βp, particle extinction coefficient αp and lidar ratio Sp from A2D raw signals are described.

High Spectral Resolution Lidar and MPLNET Micro Pulse Lidar Aerosol Optical Property Retrieval Intercomparison During the 2012 7-SEAS Field Campaign at Singapore

NASA Technical Reports Server (NTRS)

Lolli, Simone; Welton, Ellsworth J.; Campbell, James R.; Eloranta, Edwin; Holben, Brent N.; Chew, Boon Ning; Salinas, Santo V.

2014-01-01

From August 2012 to February 2013 a High Resolution Spectral Lidar (HSRL; 532 nm) was deployed at that National University of Singapore near a NASA Micro Pulse Lidar NETwork (MPLNET; 527 nm) site. A primary objective of the MPLNET lidar project is the production and dissemination of reliable Level 1 measurements and Level 2 retrieval products. This paper characterizes and quantifies error in Level 2 aerosol optical property retrievals conducted through inversion techniques that derive backscattering and extinction coefficients from MPLNET elastic single-wavelength datasets. MPLNET Level 2 retrievals for aerosol optical depth and extinction/backscatter coefficient profiles are compared with corresponding HSRL datasets, for which the instrument collects direct measurements of each using a unique optical configuration that segregates aerosol and cloud backscattered signal from molecular signal. The intercomparison is performed, and error matrices reported, for lower (0-5km) and the upper (>5km) troposphere, respectively, to distinguish uncertainties observed within and above the MPLNET instrument optical overlap regime.

[Balanced scorecard for performance measurement of a nursing organization in a Korean hospital].

PubMed

Hong, Yoonmi; Hwang, Kyung Ja; Kim, Mi Ja; Park, Chang Gi

2008-02-01

The purpose of this study was to develop a balanced scorecard (BSC) for performance measurement of a Korean hospital nursing organization and to evaluate the validity and reliability of performance measurement indicators. Two hundred fifty-nine nurses in a Korean hospital participated in a survey questionnaire that included 29-item performance evaluation indicators developed by investigators of this study based on the Kaplan and Norton's BSC (1992). Cronbach's alpha was used to test the reliability of the BSC. Exploratory and confirmatory factor analysis with a structure equation model (SEM) was applied to assess the construct validity of the BSC. Cronbach's alpha of 29 items was .948. Factor analysis of the BSC showed 5 principal components (eigen value >1.0) which explained 62.7% of the total variance, and it included a new one, community service. The SEM analysis results showed that 5 components were significant for the hospital BSC tool. High degree of reliability and validity of this BSC suggests that it may be used for performance measurements of a Korean hospital nursing organization. Future studies may consider including a balanced number of nurse managers and staff nurses in the study. Further data analysis on the relationships among factors is recommended.

Gluing for Raman lidar systems using the lamp mapping technique.

PubMed

Walker, Monique; Venable, Demetrius; Whiteman, David N

2014-12-20

In the context of combined analog and photon counting (PC) data acquisition in a Lidar system, glue coefficients are defined as constants used for converting an analog signal into a virtual PC signal. The coefficients are typically calculated using Lidar profile data taken under clear, nighttime conditions since, in the presence of clouds or high solar background, it is difficult to obtain accurate glue coefficients from Lidar backscattered data. Here we introduce a new method in which we use the lamp mapping technique (LMT) to determine glue coefficients in a manner that does not require atmospheric profiles to be acquired and permits accurate glue coefficients to be calculated when adequate Lidar profile data are not available. The LMT involves scanning a halogen lamp over the aperture of a Lidar receiver telescope such that the optical efficiency of the entire detection system is characterized. The studies shown here involve two Raman lidar systems; the first from Howard University and the second from NASA/Goddard Space Flight Center. The glue coefficients determined using the LMT and the Lidar backscattered method agreed within 1.2% for the water vapor channel and within 2.5% for the nitrogen channel for both Lidar systems. We believe this to be the first instance of the use of laboratory techniques for determining the glue coefficients for Lidar data analysis.

A Multi-Band Analytical Algorithm for Deriving Absorption and Backscattering Coefficients from Remote-Sensing Reflectance of Optically Deep Waters

NASA Technical Reports Server (NTRS)

Lee, Zhong-Ping; Carder, Kendall L.

2001-01-01

A multi-band analytical (MBA) algorithm is developed to retrieve absorption and backscattering coefficients for optically deep waters, which can be applied to data from past and current satellite sensors, as well as data from hyperspectral sensors. This MBA algorithm applies a remote-sensing reflectance model derived from the Radiative Transfer Equation, and values of absorption and backscattering coefficients are analytically calculated from values of remote-sensing reflectance. There are only limited empirical relationships involved in the algorithm, which implies that this MBA algorithm could be applied to a wide dynamic range of waters. Applying the algorithm to a simulated non-"Case 1" data set, which has no relation to the development of the algorithm, the percentage error for the total absorption coefficient at 440 nm a (sub 440) is approximately 12% for a range of 0.012 - 2.1 per meter (approximately 6% for a (sub 440) less than approximately 0.3 per meter), while a traditional band-ratio approach returns a percentage error of approximately 30%. Applying it to a field data set ranging from 0.025 to 2.0 per meter, the result for a (sub 440) is very close to that using a full spectrum optimization technique (9.6% difference). Compared to the optimization approach, the MBA algorithm cuts the computation time dramatically with only a small sacrifice in accuracy, making it suitable for processing large data sets such as satellite images. Significant improvements over empirical algorithms have also been achieved in retrieving the optical properties of optically deep waters.

SATCOM antenna siting study on P-3C aircraft, volume 1

NASA Technical Reports Server (NTRS)

Bensman, D. A.; Marhefka, R. J.

1991-01-01

The NEC-BSC (Basic Scattering Code) was used to study the performance of a SATCOM antenna on a P-3C aircraft. After plate cylinder fields are added to version 3.1 of the NEC-BSC, it is shown that the NEC-BSC can be used to accurately predict the performance of a SATCOM antenna system on a P-3C aircraft. The study illustrates that the NEC-BSC gives good results when compared with scale model measurements provided by Boeing and Lockheed.

Variability of physicochemical and mineralogical characteristics of biological soil crusts at local scale in the Sahelian zone of western Niger

NASA Astrophysics Data System (ADS)

Cancès, B.; Gommeaux, G.; Marin, B.; Ponthieu, M.; Ralahimanana, C.; Ayachi, S.; Malam Issa, O.

2012-04-01

Biological soil crusts (BSC) are organo-mineral complexes resulting from the colonisation of soil surface by living microorganisms, mainly cyanobacteria. Their form, structure and composition vary depending on characteristics related to soils, biological composition and external factors (climate conditions and land uses). This study focussed on the influence of soil characteristics and human activities on BSC properties. BSC samples from Banizoumbou (Niger) taken on protected (ungrazed) and opened (grazed) fallow lands were analysed. BSC characteristics were investigated by using chemical and mineralogical techniques, microscopic and image analysis approach as well as measurements of chlorophyll a content. Hydrophobicity measurements were also performed by the water drop penetration time method. On the basis of their colour, two types of crusts have been identified : black BSC, which occur in protected and unprotected fallow, and red BSC, which only occur in depression zones of the protected fallow. The black crusts are dominated by quartz grains trapped in the network of the filaments of Cyanobacteria. A sandy texture and a reverse grading of mineral particles are typical of physical soil crusts called sieving crusts. The dark surface coloration of the BSC is related to the high density of filamentous Cyanobacteria. Black crusts samples from protected fallow exhibit high biomass related to high cover, whereas samples from grazed fallow lands showed low biomass related to low surface cover. In both cases, hydrophobicity measurements revealed that these BSC are wettable to slightlty water repellent. However, higher values of hydrophobicity were observed on ungrazed samples compared to their grazed counterpart. This variability is likely due to the difference of cover between the two types of samples. This type of BSC corresponds to a later successional stage than the red-coloured BSC. The red BSC has a loamy-sandy texture and a normal grading typical of physical soil crusts called depositional crusts. Its mineralogy differs from the black crusts by its higher proportions of clay minerals and iron oxides (higher amounts of Al2O3 and Fe2O3). A vertical succession of BSC leads to higher content of organic carbon. The trace elements contents are also higher in this type of crust. The red colour is related to the low surface cover by Cyanobacteria. High values of hydrophobicity were measured for the red crusts, which are slightly to strongly water repellent. Compared to the underlying soil horizons, the two types of BSC differ granulometrically (higher proportions of clay and loam), mineralogically and chemically (lower SiO2 content and higher Al2O3, Fe2O3, organic carbon and trace elements contents). These results will contribute to the understanding of water dynamics at the surface of soil in the Sahelian region of Niger. They will also contribute in understanding the potential ecological roles and the spatial extent of BSC in Sahelian environment.

Phase function, backscatter, extinction, and absorption for standard radiation atmosphere and El Chichon aerosol models at visible and near-infrared wavelengths

NASA Technical Reports Server (NTRS)

Whitlock, C. H.; Suttles, J. T.; Lecroy, S. R.

1985-01-01

Tabular values of phase function, Legendre polynominal coefficients, 180 deg backscatter, and extinction cross section are given for eight wavelengths in the atmospheric windows between 0.4 and 2.2 microns. Also included are single scattering albedo, asymmetry factor, and refractive indices. These values are based on Mie theory calculations for the standard rediation atmospheres (continental, maritime, urban, unperturbed stratospheric, volcanic, upper atmospheric, soot, oceanic, dust, and water-soluble) assest measured volcanic aerosols at several time intervals following the El Chichon eruption. Comparisons of extinction to 180 deg backscatter for different aerosol models are presented and related to lidar data.

Monostatic lidar/radar invisibility using coated spheres.

PubMed

Zhai, Peng-Wang; You, Yu; Kattawar, George W; Yang, Ping

2008-02-04

The Lorenz-Mie theory is revisited to explicitly include materials whose permeability is different from unity. The expansion coefficients of the scattered field are given for light scattering by both homogeneous and coated spheres. It is shown that the backscatter is exactly zero if the impedance of the spherical particles is equal to the intrinsic impedance of the surrounding medium. If spherical particles are sufficiently large, the zero backscatter can be explained as impedance matching using the asymptotic expression for the radar backscattering cross section. In the case of a coated sphere, the shell can be regarded as a cloak if the product of the thickness and the imaginary part of the refractive index of the outer shell is large.

Backscatter and extinction measurements in cloud and drizzle at CO2 laser wavelengths

NASA Technical Reports Server (NTRS)

Jennings, S. G.

1986-01-01

The backscatter and extinction of laboratory generated cloud and drizzle sized water drops were measured at carbon dioxide laser wavelengths (predominately at lambda = 10.591 micrometers). Two distinctly different drop size regimes were studied: one which covers the range normally encompassed by natural cloud droplets and the other representative of mist or drizzle sized drops. The derivation and verification of the relation between extinction and backscatter at carbon dioxide laser wavelengths should allow the determination of large cloud drop and drizzle extinction coefficient solely from a lidar return signal without requiring knowledge of the drop size distribution. This result will also apply to precipitation sized drops so long as they are spherical.

Retrieval of Aerosol Parameters from Continuous H24 Lidar-Ceilometer Measurements

NASA Astrophysics Data System (ADS)

Dionisi, D.; Barnaba, F.; Costabile, F.; Di Liberto, L.; Gobbi, G. P.; Wille, H.

2016-06-01

Ceilometer technology is increasingly applied to the monitoring and the characterization of tropospheric aerosols. In this work, a method to estimate some key aerosol parameters (extinction coefficient, surface area concentration and volume concentration) from ceilometer measurements is presented. A numerical model has been set up to derive a mean functional relationships between backscatter and the above mentioned parameters based on a large set of simulated aerosol optical properties. A good agreement was found between the modeled backscatter and extinction coefficients and the ones measured by the EARLINET Raman lidars. The developed methodology has then been applied to the measurements acquired by a prototype Polarization Lidar-Ceilometer (PLC). This PLC instrument was developed within the EC- LIFE+ project "DIAPASON" as an upgrade of the commercial, single-channel Jenoptik CHM15k system. The PLC run continuously (h24) close to Rome (Italy) for a whole year (2013-2014). Retrievals of the aerosol backscatter coefficient at 1064 nm and of the relevant aerosol properties were performed using the proposed methodology. This information, coupled to some key aerosol type identification made possible by the depolarization channel, allowed a year-round characterization of the aerosol field at this site. Examples are given to show how this technology coupled to appropriate data inversion methods is potentially useful in the operational monitoring of parameters of air quality and meteorological interest.

Temporal Stability of Soil Moisture and Radar Backscatter Observed by the Advanced Synthetic Aperture Radar (ASAR)

PubMed Central

Wagner, Wolfgang; Pathe, Carsten; Doubkova, Marcela; Sabel, Daniel; Bartsch, Annett; Hasenauer, Stefan; Blöschl, Günter; Scipal, Klaus; Martínez-Fernández, José; Löw, Alexander

2008-01-01

The high spatio-temporal variability of soil moisture is the result of atmospheric forcing and redistribution processes related to terrain, soil, and vegetation characteristics. Despite this high variability, many field studies have shown that in the temporal domain soil moisture measured at specific locations is correlated to the mean soil moisture content over an area. Since the measurements taken by Synthetic Aperture Radar (SAR) instruments are very sensitive to soil moisture it is hypothesized that the temporally stable soil moisture patterns are reflected in the radar backscatter measurements. To verify this hypothesis 73 Wide Swath (WS) images have been acquired by the ENVISAT Advanced Synthetic Aperture Radar (ASAR) over the REMEDHUS soil moisture network located in the Duero basin, Spain. It is found that a time-invariant linear relationship is well suited for relating local scale (pixel) and regional scale (50 km) backscatter. The observed linear model coefficients can be estimated by considering the scattering properties of the terrain and vegetation and the soil moisture scaling properties. For both linear model coefficients, the relative error between observed and modelled values is less than 5 % and the coefficient of determination (R2) is 86 %. The results are of relevance for interpreting and downscaling coarse resolution soil moisture data retrieved from active (METOP ASCAT) and passive (SMOS, AMSR-E) instruments. PMID:27879759

Study of sea-surface slope distribution and its effect on radar backscatter based on Global Precipitation Measurement Ku-band precipitation radar measurements

NASA Astrophysics Data System (ADS)

Yan, Qiushuang; Zhang, Jie; Fan, Chenqing; Wang, Jing; Meng, Junmin

2018-01-01

The collocated normalized radar backscattering cross-section measurements from the Global Precipitation Measurement (GPM) Ku-band precipitation radar (KuPR) and the winds from the moored buoys are used to study the effect of different sea-surface slope probability density functions (PDFs), including the Gaussian PDF, the Gram-Charlier PDF, and the Liu PDF, on the geometrical optics (GO) model predictions of the radar backscatter at low incidence angles (0 deg to 18 deg) at different sea states. First, the peakedness coefficient in the Liu distribution is determined using the collocations at the normal incidence angle, and the results indicate that the peakedness coefficient is a nonlinear function of the wind speed. Then, the performance of the modified Liu distribution, i.e., Liu distribution using the obtained peakedness coefficient estimate; the Gaussian distribution; and the Gram-Charlier distribution is analyzed. The results show that the GO model predictions with the modified Liu distribution agree best with the KuPR measurements, followed by the predictions with the Gaussian distribution, while the predictions with the Gram-Charlier distribution have larger differences as the total or the slick filtered, not the radar filtered, probability density is included in the distribution. The best-performing distribution changes with incidence angle and changes with wind speed.

Measure of Backscatter for small particles of atmosphere by lasers

NASA Astrophysics Data System (ADS)

Abud, Mariam M.

2018-05-01

It developed a program for the atmosphere to study the backscattering for contents gas and molecules, aerosol, fog, clouds and rain droplets. By using Rayleigh, Mie and geometric scattering. The aim of research, using different types of lasers from various optical region, is to calculate differential cross scatter section and backscatter of atmosphere component in one layer from height 10-2000m. 180° is backscattering angle using ISA standard sea level condition P=1013.25 (kpa) at t0=15 ° C.and then calculated the density of molecules and water vapor molecules represented D in kg/m3. Results reflected index consist of the large value of the real part and imaginary m=1.463-0.028i.this research diff. scatter cross section of different component of atmosphere layer decreased vs. wavelengths. The purpose of lider research to find backscatter from UV to IR laser within the optical range in the atmosphere and measurement of excitation and analysis of backscatter signals. Recently, the atmosphere of Iraq has become full of dust and pollution, so by knowing the differential cross scatter section and backscatter of atmosphere. Relation between total Rayleigh scatter coefficient & type of particles include fog and clouds, aerosols and water droplets (-0.01, 0.025,- 0.005) m-1/sr-1.

Continuous atmospheric boundary layer observations in the coastal urban area of Barcelona during SAPUSS

NASA Astrophysics Data System (ADS)

Pandolfi, M.; Martucci, G.; Querol, X.; Alastuey, A.; Wilsenack, F.; Frey, S.; O'Dowd, C. D.; Dall'Osto, M.

2013-05-01

Continuous measurements of surface mixed layer (SML), decoupled residual/convective layer (DRCL) and aerosol backscatter coefficient were performed within the Barcelona (Spain) boundary layer from September to October 2010 (30 days) in the framework of the SAPUSS (Solving Aerosol Problems by Using Synergistic Strategies) field campaign. Two near-infrared ceilometers (Jenoptik CHM15K), vertically and horizontally probing (only vertical profiles are herein discussed), were deployed. Ceilometer-based DRCLs (1761 ± 363 m a.g.l.) averaged over the campaign duration were twice as high as the mean SML (904 ± 273 m a.g.l.). Both DRCL and SML showed a marked SML diurnal cycle. Ceilometer data were compared with potential temperature profiles measured by daily radiosounding (twice a day, midnight and midday) to interpret the boundary layer structure in the coastal urban area of Barcelona. The overall agreement (R2 = 0.80) between the ceilometer-retrieved and radiosounding-based SML heights (h) revealed overestimation of the SML by the ceilometer (Δh=145 ± 145 m). After separating the data in accordance with different atmospheric scenarios, the lowest SML (736 ± 183 m) and DRCL (1573 ± 428 m) were recorded during warm North African (NAF) advected air mass. By contrast, higher SML and DRCL were observed during stagnant Regional (REG) (911 ± 234 m and 1769 ± 314 m, respectively) and cold Atlantic (ATL) (965 ± 222 m and 1878 ± 290 m, respectively) air masses. In addition to being the lowest, the SML during the NAF scenario frequently showed a flat upper boundary throughout the day possibly because of the strong winds from the Mediterranean Sea limiting the midday SML convective growth. The mean backscatter coefficients were calculated at two selected heights representative of middle and top SML portions, i.e. β500 = 0.59 ± 0.45 Mm-1 sr-1 and β800 = 0.87 ± 0.68 Mm-1 sr-1 at 500 m and 800 m a.g.l., respectively. The highest backscatter coefficients were observed during NAF (β500 = 0.77 ± 0.57 Mm-1 sr-1) when compared with ATL (β500 = 0.51 ± 0.44 Mm-1 sr-1) and REG (β500 = 0.64 ± 0.39 Mm-1 sr-1). The relationship between the vertical change in backscatter coefficient and atmospheric stability (∂θ/∂z) was investigated in the first 3000 m a.g.l., aiming to study how the unstable, stable or neutral atmospheric conditions of the atmosphere alter the distribution of aerosol backscatter with height over Barcelona. A positive correlation between unstable conditions and enhanced backscatter and vice versa was found.

An analytical model for light backscattering by coccoliths and coccospheres of Emiliania huxleyi.

PubMed

Fournier, Georges; Neukermans, Griet

2017-06-26

We present an analytical model for light backscattering by coccoliths and coccolithophores of the marine calcifying phytoplankter Emiliania huxleyi. The model is based on the separation of the effects of diffraction, refraction, and reflection on scattering, a valid assumption for particle sizes typical of coccoliths and coccolithophores. Our model results match closely with results from an exact scattering code that uses complex particle geometry and our model also mimics well abrupt transitions in scattering magnitude. Finally, we apply our model to predict changes in the spectral backscattering coefficient during an Emiliania huxleyi bloom with results that closely match in situ measurements. Because our model captures the key features that control the light backscattering process, it can be generalized to coccoliths and coccolithophores of different morphologies which can be obtained from size-calibrated electron microphotographs. Matlab codes of this model are provided as supplementary material.

Effect of species structure and dielectric constant on C-band forest backscatter

NASA Technical Reports Server (NTRS)

Lang, R. H.; Landry, R.; Kilic, O.; Chauhan, N.; Khadr, N.; Leckie, D.

1993-01-01

A joint experiment between Canadian and USA research teams was conducted early in Oct. 1992 to determine the effect of species structure and dielectric variations on forest backscatter. Two stands, one red pine and one jack pine, in the Petawawa National Forestry Institute (PNFI) were utilized for the experiment. Extensive tree architecture measurements had been taken by the Canada Centre for Remote Sensing (CCRS) several months earlier by employing a Total Station surveying instrument which provides detailed information on branch structure. A second part of the experiment consisted of cutting down several trees and using dielectric probes to measure branch and needle permittivity values at both sites. The dielectric and the tree geometry data were used in the George Washington University (GWU) Vegetation Model to determine the C band backscattering coefficients of the individual stands for VV polarization. The model results show that backscatter at C band comes mainly from the needles and small branches and the upper portion of the trunks acts only as an attenuator. A discussion of variation of backscatter with specie structure and how dielectric variations in needles for both species may affect the total backscatter returns is provided.

Sampling of Stochastic Input Parameters for Rockfall Calculations and for Structural Response Calculations Under Vibratory Ground Motion

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. Gross

2004-09-01

The purpose of this scientific analysis is to define the sampled values of stochastic (random) input parameters for (1) rockfall calculations in the lithophysal and nonlithophysal zones under vibratory ground motions, and (2) structural response calculations for the drip shield and waste package under vibratory ground motions. This analysis supplies: (1) Sampled values of ground motion time history and synthetic fracture pattern for analysis of rockfall in emplacement drifts in nonlithophysal rock (Section 6.3 of ''Drift Degradation Analysis'', BSC 2004 [DIRS 166107]); (2) Sampled values of ground motion time history and rock mechanical properties category for analysis of rockfall inmore » emplacement drifts in lithophysal rock (Section 6.4 of ''Drift Degradation Analysis'', BSC 2004 [DIRS 166107]); (3) Sampled values of ground motion time history and metal to metal and metal to rock friction coefficient for analysis of waste package and drip shield damage to vibratory motion in ''Structural Calculations of Waste Package Exposed to Vibratory Ground Motion'' (BSC 2004 [DIRS 167083]) and in ''Structural Calculations of Drip Shield Exposed to Vibratory Ground Motion'' (BSC 2003 [DIRS 163425]). The sampled values are indices representing the number of ground motion time histories, number of fracture patterns and rock mass properties categories. These indices are translated into actual values within the respective analysis and model reports or calculations. This report identifies the uncertain parameters and documents the sampled values for these parameters. The sampled values are determined by GoldSim V6.04.007 [DIRS 151202] calculations using appropriate distribution types and parameter ranges. No software development or model development was required for these calculations. The calculation of the sampled values allows parameter uncertainty to be incorporated into the rockfall and structural response calculations that support development of the seismic scenario for the Total System Performance Assessment for the License Application (TSPA-LA). The results from this scientific analysis also address project requirements related to parameter uncertainty, as specified in the acceptance criteria in ''Yucca Mountain Review Plan, Final Report'' (NRC 2003 [DIRS 163274]). This document was prepared under the direction of ''Technical Work Plan for: Regulatory Integration Modeling of Drift Degradation, Waste Package and Drip Shield Vibratory Motion and Seismic Consequences'' (BSC 2004 [DIRS 170528]) which directed the work identified in work package ARTM05. This document was prepared under procedure AP-SIII.9Q, ''Scientific Analyses''. There are no specific known limitations to this analysis.« less

78 FR 15369 - Board of Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-11

... Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR) In accordance with... Prevention (CDC), and the Director, Office of Public Health Preparedness and Response (OPHPR), concerning... BSC deliberation on the following topics: Public Health Preparedness and Response Policy Updates...

[Application of the balanced scorecard in nursing practice].

PubMed

Huang, Tsai-Yu; Chwo, Miao-Ju

2004-02-01

Kaplan and Norton's balanced scorecard (BSC) was developed in 1992. It was designed to be both a performance framework and a management methodology. The BSC enables an organization to convert its mission and vision into specific strategic objectives across four perspectives: (1) the financial perspective, (2) the customer perspective, (3) the internal business process perspective, and (4) the learning and growth perspective. Emphasis is focused on the balance of internal and external, outcome and future, and subjective and objective measures. Currently, some health care organizations have implemented the concept of the BSC as a performance measurement tool and are convinced that the BSC can be of great value to an organization. This paper provides development of the BSC and its application in the health care system and nursing practice.

Biological soil crusts exhibit a dynamic response to seasonal rain and release from grazing with implications for soil stability

USGS Publications Warehouse

Jimenez, Aguilar A.; Huber-Sannwald, E.; Belnap, J.; Smart, D.R.; Arredondo, Moreno J.T.

2009-01-01

In Northern Mexico, long-term grazing has substantially degraded semiarid landscapes. In semiarid systems, ecological and hydrological processes are strongly coupled by patchy plant distribution and biological soil crust (BSC) cover in plant-free interspaces. In this study, we asked: 1) how responsive are BSC cover/composition to a drying/wetting cycle and two-year grazing removal, and 2) what are the implications for soil erosion? We characterized BSC morphotypes and their influence on soil stability under grazed/non-grazed conditions during a dry and wet season. Light- and dark-colored cyanobacteria were dominant at the plant tussock and community level. Cover changes in these two groups differed after a rainy season and in response to grazing removal. Lichens with continuous thalli were more vulnerable to grazing than those with semi-continuous/discontinuous thalli after the dry season. Microsites around tussocks facilitated BSC colonization compared to interspaces. Lichen and cyanobacteria morphotypes differentially enhanced resistance to soil erosion; consequently, surface soil stability depends on the spatial distribution of BSC morphotypes, suggesting soil stability may be as dynamic as changes in the type of BSC cover. Longer-term spatially detailed studies are necessary to elicit spatiotemporal dynamics of BSC communities and their functional role in biotically and abiotically variable environments. ?? 2009 Elsevier Ltd.

Habitat stress initiates changes in composition, CO2 gas exchange and C-allocation as life traits in biological soil crusts.

PubMed

Colesie, Claudia; Green, T G Allan; Haferkamp, Ilka; Büdel, Burkhard

2014-10-01

Biological soil crusts (BSC) are the dominant functional vegetation unit in some of the harshest habitats in the world. We assessed BSC response to stress through changes in biotic composition, CO2 gas exchange and carbon allocation in three lichen-dominated BSC from habitats with different stress levels, two more extreme sites in Antarctica and one moderate site in Germany. Maximal net photosynthesis (NP) was identical, whereas the water content to achieve maximal NP was substantially lower in the Antarctic sites, this apparently being achieved by changes in biomass allocation. Optimal NP temperatures reflected local climate. The Antarctic BSC allocated fixed carbon (tracked using (14)CO2) mostly to the alcohol soluble pool (low-molecular weight sugars, sugar alcohols), which has an important role in desiccation and freezing resistance and antioxidant protection. In contrast, BSC at the moderate site showed greater carbon allocation into the polysaccharide pool, indicating a tendency towards growth. The results indicate that the BSC of the more stressed Antarctic sites emphasise survival rather than growth. Changes in BSC are adaptive and at multiple levels and we identify benefits and risks attached to changing life traits, as well as describing the ecophysiological mechanisms that underlie them.

Towards Snowpack Characterization using C-band Synthetic Aperture Radar (SAR)

NASA Astrophysics Data System (ADS)

Park, J.; Forman, B. A.

2017-12-01

Sentinel 1A and 1B, operated by the European Space Agency (ESA), carries a C-band synthetic aperture radar (SAR) sensor that can be used to monitor terrestrial snow properties. This study explores the relationship between terrestrial snow-covered area, snow depth, and snow water equivalent with Sentinel 1 backscatter observations in order to better characterize snow mass. Ground-based observations collected by the National Oceanic and Atmospheric Administration - Cooperative Remote Sensing Science and Technology Center (NOAA-CREST) in Caribou, Maine in the United States are also used in the comparative analysis. Sentinel 1 Ground Range Detected (GRD) imagery with Interferometric Wide swath (IW) were preprocessed through a series of steps accounting for thermal noise, sensor orbit, radiometric calibration, speckle filtering, and terrain correction using ESA's Sentinel Application Platform (SNAP) software package, which is an open-source module written in Python. Comparisons of dual-polarized backscatter coefficients (i.e., σVV and σVH) with in-situ measurements of snow depth and SWE suggest that cross-polarized backscatter observations exhibit a modest correlation between both snow depth and SWE. In the case of the snow-covered area, a multi-temporal change detection method was used. Results using Sentinel 1 yield similar spatial patterns as when using hyperspectral observations collected by the MODerate Resolution Imaging Spectroradiometer (MODIS). These preliminary results suggest the potential application of Sentinel 1A/1B backscatter coefficients towards improved discrimination of snow cover, snow depth, and SWE. One goal of this research is to eventually merge C-band SAR backscatter observations with other snow information (e.g., passive microwave brightness temperatures) as part of a multi-sensor snow assimilation framework.

Backscattering Measurement From a Single Microdroplet

PubMed Central

Lee, Jungwoo; Chang, Jin Ho; Jeong, Jong Seob; Lee, Changyang; Teh, Shia-Yen; Lee, Abraham; Shung, K. Kirk

2011-01-01

Backscattering measurements for acoustically trapped lipid droplets were undertaken by employing a P[VDF-TrFE] broadband transducer of f-number = 1, with a bandwidth of 112%. The wide bandwidth allowed the transmission of the 45 MHz trapping signal and the 15 MHz sensing signal using the same transducer. Tone bursts at 45 MHz were first transmitted by the transducer to hold a single droplet at the focus (or the center of the trap) and separate it from its neighboring droplets by translating the transducer perpendicularly to the beam axis. Subsequently, 15 MHz probing pulses were sent to the trapped droplet and the backscattered RF echo signal received by the same transducer. The measured beam width at 15 MHz was measured to be 120 μm. The integrated backscatter (IB) coefficient of an individual droplet was determined within the 6-dB bandwidth of the transmit pulse by normalizing the power spectrum of the RF signal to the reference spectrum obtained from a flat reflector. The mean IB coefficient for droplets with a 64 μm average diameter (denoted as cluster A) was −107 dB, whereas it was −93 dB for 90-μm droplets (cluster B). The standard deviation was 0.9 dB for each cluster. The experimental values were then compared with those computed with the T-matrix method and a good agreement was found: the difference was as small as 1 dB for both clusters. These results suggest that this approach might be useful as a means for measuring ultrasonic backscattering from a single microparticle, and illustrate the potential of acoustic sensing for cell sorting. PMID:21507767

Establishment proper of the balanced scorecard indicators to support decision making in a university: a case study in Institut Teknologi Indonesia

NASA Astrophysics Data System (ADS)

Theresia, L.; Lahuddin, A. H.; Bangun, R.

2017-12-01

Balanced Scorecard (BSC) is a powerful tool in decision making process. Nevertheless, it is not rare that the BSC does not give satisfactory results because the indicators chosen do not reflect the needs of the organization. Therefore, indicator establishment is very crucial in the utilization of BSC. This research aims to determine the indicators BSC for a university and the research is a case study in Institut Teknologi Indonesia (ITI). In this study, BSC structure and indicators, comparison made by 4 previous researchers was used as the initial guide to determine the structure and indicators of ITI. And then, questionnaires were distributed to selected respondents and a focus group discussion (FGD) was conducted in order to produce indicators of BSC based on the mental model of the ITI. It is found 15 indicators based on the mental model of ITI. Furthermore, the relationships between the indicators are seen as dynamic relationships, and by using system dynamics, some feedback loops that are considered critical to organizational success can be identified and isolated.

Success factors for implementation of the balanced scorecard in a NHS multi-agency setting.

PubMed

Radnor, Zoe; Lovell, Bill

2003-01-01

Even though the balanced scorecard (BSC) has become a highly popular performance management tool, usage in local public sector National Health Service (NHS) organisations is still rare. This paper conditionally outlines some grounds in supporting such usage. In particular underlying conceptual concerns with the BSC system and its implementation pitfalls require full consideration. This paper then outlines some factors to be taken into account for "successful" BSC implementation in a NHS multi-agency setting. These findings emerged from a series of focus groups that took place with contributors drawn from all the key organisations within the Bradford Health Action Zone. Finally, this paper argues that if key criteria are met, successful implementation of the BSC may then proceed. However, "blind" BSC implementation without consideration of these factors may result in potential "failure".

Use of acoustic backscatter to estimate continuous suspended sediment and phosphorus concentrations in the Barton River, northern Vermont, 2010-2013

USGS Publications Warehouse

Medalie, Laura; Chalmers, Ann T.; Kiah, Richard G.; Copans, Benjamin

2014-01-01

The U.S. Geological Survey, in cooperation with the Vermont Department of Environmental Conservation, investigated the use of acoustic backscatter to estimate concentrations of suspended sediment and total phosphorus at the Barton River near Coventry, Vermont. The hypothesis was that acoustic backscatter—the reflection of sound waves off objects back to the source from which they came—measured by an acoustic Doppler profiler (ADP) and recorded as ancillary data for the calculation of discharge, also could be used to generate a continuous concentration record of suspended sediment and phosphorus at the streamgage, thereby deriving added value from the instrument. Suspended-sediment and phosphorus concentrations are of particular interest in Vermont, where impairment of surface waters by suspended sediments and phosphorus is a major concern. Regression models for estimating suspended-sediment concentrations (SSCs) and total phosphorus concentrations evaluated several independent variables: measured backscatter (MB), water-corrected backscatter (WCB), sediment-corrected backscatter (SCB), discharge, fluid-absorption coefficient, sediment-driven acoustic attenuation coefficient, and discharge hysteresis. The best regression equations for estimating SSC used backscatter as the predictor, reflecting the direct relation between acoustic backscatter and SSC. Backscatter was a better predictor of SSC than discharge in part because hysteresis between SSC and backscatter was less than for SSC and discharge. All three backscatter variables—MB, WCB, and SCB—performed equally as predictors of SSC and phosphorus concentrations at the Barton River site. The similar abilities to predict SSC among backscatter terms may partially be attributed to the low values and narrow range of the sediment-driven acoustic attenuation in the Barton River. The regression based on SCB was selected for estimating SSC because it removes potential bias caused by attenuation and temperature fluctuations. The best regression model for estimating phosphorus concentrations included terms for discharge and discharge hysteresis. The finding that discharge hysteresis was a significant predictor of phosphorus concentrations might be related to preferential sorption of phosphorus to fine-grained sediments, which have been found to be particularly sensitive to hysteresis. Regression models designed to estimate phosphorus concentrations had less predictive power than the models for SSCs. Data from the Barton River did not fully support one of the study’s hypotheses—that backscatter is mostly caused by sands, and attenuation is mostly caused by fines. Sands, fines, and total SSCs in the Barton River all related better to backscatter than to sediment-driven acoustic attenuation. The weak relation between SSC and sediment-driven acoustic attenuation may be related to the low values and narrow range of SSCs and sediment attenuations observed at Barton River. A weak relation between SSC and sediment-driven acoustic attenuation also suggests that the diameters of the fine-sized suspended sediments in the Barton River may be predominantly greater than 20 micrometers (μm). Long-term changes in the particle-size distribution (PSD) were not observed in Barton River; however, some degree of within-storm changes in sediment source and possibly PSD were inferred from the hysteresis between SSC and SCB.

Effects of an Early Successional Biological Soil Crust from a Temperate Coastal Sand Dune (NE Germany) on Soil Elemental Stoichiometry and Phosphatase Activity.

PubMed

Schaub, Iris; Baum, Christel; Schumann, Rhena; Karsten, Ulf

2018-06-20

Early successional biological soil crusts (BSCs), a consortium of bacteria, cyanobacteria, and other microalgae, are one of the first settlement stages on temperate coastal sand dunes. In this study, we investigated the algal biomass (Chlorophyll a (Chl a)), algal (C algal ) and microbial carbon (C mic ), elemental stoichiometry (C:N:P), and acid and alkaline phosphatase activity (AcidPA and AlkPA) of two algae-dominated BSCs from a coastal white dune (northeast Germany, on the southwestern Baltic Sea) which differed in the exposure to wind forces. The dune sediment (DS) was generally low in total carbon (TC), nitrogen (TN), and phosphorus (TP). These elements, together with the soil organic matter (SOM) accumulated in the BSC layer and in the sediment underneath (crust sediment CS), leading to initial soil development. The more disturbed BSC (BSC1) exhibited lower algal and microbial biomass and lower C algal /C mic ratios than the undisturbed BSC (BSC2). The BSC1 accumulated more organic carbon (OC) than BSC2. However, the OC in the BSC2 was more effectively incorporated into C mic than in the BSC1, as indicated by lower OC:C mic ratios. The AcidPA (1.1-1.3 μmol g -1  DM h -1 or 147-178 μg g -1  DM h -1 ) and AlkPA (2.7-5.5 μmol g -1  DM h -1 or 372-764 μg g -1  DM h -1 ) were low in both BSCs. The PA, together with the elemental stoichiometry, indicated no P limitation of both BSCs but rather water limitation followed by N limitation for the algae community and a carbon limitation for the microbial community. Our results explain the observed distribution of early successional and more developed BSCs on the sand dune.

Evaluation of behaviour of Lachancea thermotolerans biocontrol agents on grape fermentations.

PubMed

Nally, M C; Ponsone, M L; Pesce, V M; Toro, M E; Vazquez, F; Chulze, S

2018-07-01

Previous researches have showed that Lachancea thermotolerans strains RCKT4 and RCKT5 inhibited the growth of Aspergillus. However, currently, there are no data on their nutritional preferences, as a possible substrate competitor against Saccharomyces cerevisiae, and their effects on fermentation. In this work, we observed that the biocontrol yeasts and S. cerevisiae BSc203, based on the utilization of 16 carbonate sources, revealed significant differences in the nutritional profile (biocontrol yeasts NS:0·25, BSc203 NS:0·56). Lachancea thermotolerans strains did not occupy the same niche as that of BSc203 (NOI:0·44). The biocontrol agents and BSc203 presented similar competitive attitude in terms of the sugar, ethanol and sulphite tolerances. During fermentation, the biocontrol yeasts were found to tolerate up to 12% v/v ethanol, 250 mg ml -1 of total SO 2 and 30° Brix sugar. In mixed cultures, L. thermotolerans strains did not negatively affect the growth of BSc203 and the wine quality, except when RCKT4 was initially inoculated at a high proportion in the mixed culture 1MSK4 (1%BSc203/99%RCKT4), resulting in a lower production of CO 2 and ethanol, in comparison with pure BSc203. RCKT5, at a high proportion, in 1MSK5 (1%BSc203/99%RCKT5) presented promising oenological properties. This fermentation showed lower acetic acid contents and higher total acidity than pure BSc203. Generally it is not evaluated if the biofungicide yeasts sprayed on vegetables alter the quality of the fermented products. This work focused on the importance of assessing the possible effects of yeast-based fungicides used in vineyards on grape fermentation, especially on Saccharomyces cerevisiae growth. In this context, the competition between biofungicide yeasts and S. cerevisiae under winemaking conditions is investigated. © 2018 The Society for Applied Microbiology.

Aerosol profiling using the ceilometer network of the German Meteorological Service

NASA Astrophysics Data System (ADS)

Flentje, H.; Heese, B.; Reichardt, J.; Thomas, W.

2010-08-01

The German Meteorological Service (DWD) operates about 52 lidar ceilometers within its synoptic observations network, covering Germany. These affordable low-power lidar systems provide spatially and temporally high resolved aerosol backscatter profiles which can operationally provide quasi 3-D distributions of particle backscatter intensity. Intentionally designed for cloud height detection, recent significant improvements allow following the development of the boundary layer and to detect denser particle plumes in the free tropospere like volcanic ash, Saharan dust or fire smoke. Thus the network builds a powerful aerosol plume alerting and tracking system. If auxiliary aerosol information is available, the particle backscatter coefficient, the extinction coefficient and even particle mass concentrations may be estimated, with however large uncertainties. Therefore, large synergistic benefit is achieved if the ceilometers are linked to existing lidar networks like EARLINET or integrated into WMO's envisioined Global Aerosol Lidar Observation Network GALION. To this end, we demonstrate the potential and limitations of ceilometer networks by means of three representative aerosol episodes over Europe, namely Sahara dust, Mediterranean fire smoke and, more detailed, the Icelandic Eyjafjoll volcano eruption from mid April 2010 onwards. The DWD (Jenoptik CHM15k) lidar ceilometer network tracked the Eyjafjoll ash layers over Germany and roughly estimated peak extinction coefficients and mass concentrations on 17 April of 4-6(± 2) 10-4 m-1 and 500-750(± 300) μg/m-3, respectively, based on co-located aerosol optical depth, nephelometer (scattering coefficient) and particle mass concentration measurements. Though large, the uncertainties are small enough to let the network suit for example as aviation advisory tool, indicating whether the legal flight ban threshold of presently 2 mg/m3 is imminent to be exceeded.

Estimation of black carbon content for biomass burning aerosols from multi-channel Raman lidar data

NASA Astrophysics Data System (ADS)

Talianu, Camelia; Marmureanu, Luminita; Nicolae, Doina

2015-04-01

Biomass burning due to natural processes (forest fires) or anthropical activities (agriculture, thermal power stations, domestic heating) is an important source of aerosols with a high content of carbon components (black carbon and organic carbon). Multi-channel Raman lidars provide information on the spectral dependence of the backscatter and extinction coefficients, embedding information on the black carbon content. Aerosols with a high content of black carbon have large extinction coefficients and small backscatter coefficients (strong absorption), while aerosols with high content of organic carbon have large backscatter coefficients (weak absorption). This paper presents a method based on radiative calculations to estimate the black carbon content of biomass burning aerosols from 3b+2a+1d lidar signals. Data is collected at Magurele, Romania, at the cross-road of air masses coming from Ukraine, Russia and Greece, where burning events are frequent during both cold and hot seasons. Aerosols are transported in the free troposphere, generally in the 2-4 km altitude range, and reaches the lidar location after 2-3 days. Optical data are collected between 2011-2012 by a multi-channel Raman lidar and follows the quality assurance program of EARLINET. Radiative calculations are made with libRadTran, an open source radiative model developed by ESA. Validation of the retrievals is made by comparison to a co-located C-ToF Aerosol Mass Spectrometer. Keywords: Lidar, aerosols, biomass burning, radiative model, black carbon Acknowledgment: This work has been supported by grants of the Romanian National Authority for Scientific Research, Programme for Research- Space Technology and Advanced Research - STAR, project no. 39/2012 - SIAFIM, and by Romanian Partnerships in priority areas PNII implemented with MEN-UEFISCDI support, project no. 309/2014 - MOBBE

Detection and Evaluation of Early Breast Cancer via Magnetic Resonance Imaging: Studies of Mouse Models and Clinical Implementation

DTIC Science & Technology

2007-03-01

Krausz 3 M.D., Marta Zamora1 B.Sc., Erica Markewicz1 B.Sc., Sean Foxley1 M.Sc., Xiaobing Fan1 Ph.D., Dianna Pang2 B.Sc., Brad Williams2 B.Sc., So...of prostate tumors in mice. NMR Biomed 2005; 18:285-292. 28. Szabo BK, Aspelin P, Wiberg MK, Bone B. Dynamic MR imaging of the breast. Analysis of...enhancement (E1, Epeak) and time to peak enhancement (Tpeak) were measured for each curve as performed by Szabo et al (24). The signal enhancement

Continuous atmospheric boundary layer observations in the coastal urban area of Barcelona, Spain

NASA Astrophysics Data System (ADS)

Pandolfi, M.; Martucci, G.; Querol, X.; Alastuey, A.; Wilsenack, F.; Frey, S.; O'Dowd, C. D.; Dall'Osto, M.

2013-01-01

Continuous measurements of Surface Mixed Layer (SML), Decoupled Residual/Convective Layer (DRCL) and aerosol backscatter coefficient were performed within the Barcelona (NE Spain) boundary layer from September to October 2010 (30 days) in the framework of the SAPUSS (Solving Aerosol Problems Using Synergistic Strategies) field campaign. Two near-infrared ceilometers (Jenoptik CHM15K) vertically and horizontally-probing (only vertical profiles are discussed) were deployed during SAPUSS and compared with potential temperature profiles measured by daily radiosounding (midnight and midday) to interpret the boundary layer structure in the urban area of Barcelona. Ceilometer-based DRCL (1761±363 m a.g.l.) averaged over the campaign duration were twice as high as the mean SML (904±273 m a.g.l.) with a marked SML diurnal cycle. The overall agreement between the ceilometer-retrieved and radiosounding-based SML heights (R2=0.8) revealed overestimation of the SML by the ceilometer (Δh=145±145 m). After separating the data in accordance with different atmospheric scenarios, the lowest SML (736±183 m) and DRCL (1573±428 m) were recorded during warm North African (NAF) advected air mass. By contrast, higher SML and DRCL were observed during stagnant regional (REG) (911±234 m and 1769±314 m, respectively) and cold Atlantic (ATL) (965±222 m and 1878±290 m, respectively) air masses. The SML during the NAF scenario frequently showed a flat upper boundary throughout the day because of strong winds from the Mediterranean Sea that limit the midday SML convective growth observed during ATL and REG scenarios. The mean backscatter coefficients were calculated at two selected heights as representative of middle and top SML portions, i.e. β500=0.59±0.45 M m-1 sr-1 and β800=0.87±0.68 M m-1 sr-1 at 500 m and 800 m a.g.l., respectively. The highest backscatter coefficients were observed during NAF (β500=0.77±0.57 M m-1 sr-1) when compared with ATL (β500= 0.51±0.44 M m-1 sr-1) and REG (β500= 0.64±0.39 M m-1 sr-1). The relationship between the vertical change in backscatter coefficient and atmospheric stability (∂θ/∂z) was investigated in the first 3000 m a.g.l., demonstrating a positive correlation between unstable conditions and enhanced backscatter and vice versa.

Germination, survival and growth of three vascular plants on biological soil crusts from a Mexican tropical desert.

PubMed

Godínez-Alvarez, H; Morín, C; Rivera-Aguilar, V

2012-01-01

Information about the effects of biological soil crusts (BSC) on germination, seedling survival and growth of vascular plants is controversial because they can have positive, neutral or negative effects. This controversy may be because most studies conducted until now have just analysed one or two recruitment stages independently. To understand the BSC effects on vascular plants, it is necessary to consider each stage of the recruitment process and synthesise all this information. The goal of this study was twofold. First, we analyse germination, seedling survival and growth of three vascular plants (Agave marmorata, Prosopis laevigata and Neobuxbaumia tetetzo) on BSC (cyanobacteria and mixed crust) from a tropical desert region of south-central México. Second, we synthesise the information to determine the total effect of BSC on plant species performance. We conducted experiments under controlled conditions to evaluate the proportion of germinated seeds, proportion of surviving seedlings and seedling dry weight in BSC and bare soil. Results showed that BSC have different effects on germination, seedling survival and growth of plant species. Plant species performance was qualitatively higher on BSC than bare soil. The highest performance of A. marmorata and P. laevigata was observed on cyanobacteria and mixed crusts, respectively. The highest performance of N. tetetzo was on both crust types. © 2011 German Botanical Society and The Royal Botanical Society of the Netherlands.

Accurate estimation of sigma(exp 0) using AIRSAR data

NASA Technical Reports Server (NTRS)

Holecz, Francesco; Rignot, Eric

1995-01-01

During recent years signature analysis, classification, and modeling of Synthetic Aperture Radar (SAR) data as well as estimation of geophysical parameters from SAR data have received a great deal of interest. An important requirement for the quantitative use of SAR data is the accurate estimation of the backscattering coefficient sigma(exp 0). In terrain with relief variations radar signals are distorted due to the projection of the scene topography into the slant range-Doppler plane. The effect of these variations is to change the physical size of the scattering area, leading to errors in the radar backscatter values and incidence angle. For this reason the local incidence angle, derived from sensor position and Digital Elevation Model (DEM) data must always be considered. Especially in the airborne case, the antenna gain pattern can be an additional source of radiometric error, because the radar look angle is not known precisely as a result of the the aircraft motions and the local surface topography. Consequently, radiometric distortions due to the antenna gain pattern must also be corrected for each resolution cell, by taking into account aircraft displacements (position and attitude) and position of the backscatter element, defined by the DEM data. In this paper, a method to derive an accurate estimation of the backscattering coefficient using NASA/JPL AIRSAR data is presented. The results are evaluated in terms of geometric accuracy, radiometric variations of sigma(exp 0), and precision of the estimated forest biomass.

Airborne Coherent Lidar for Advanced In-Flight Measurements (ACLAIM) Flight Testing of the Lidar Sensor

NASA Technical Reports Server (NTRS)

Soreide, David C.; Bogue, Rodney K.; Ehernberger, L. J.; Hannon, Stephen M.; Bowdle, David A.

2000-01-01

The purpose of the ACLAIM program is ultimately to establish the viability of light detection and ranging (lidar) as a forward-looking sensor for turbulence. The goals of this flight test are to: 1) demonstrate that the ACLAIM lidar system operates reliably in a flight test environment, 2) measure the performance of the lidar as a function of the aerosol backscatter coefficient (beta), 3) use the lidar system to measure atmospheric turbulence and compare these measurements to onboard gust measurements, and 4) make measurements of the aerosol backscatter coefficient, its probability distribution and spatial distribution. The scope of this paper is to briefly describe the ACLAIM system and present examples of ACLAIM operation in flight, including comparisons with independent measurements of wind gusts, gust-induced normal acceleration, and the derived eddy dissipation rate.

Cloning and characterization of a novel sigma-like glutathione S-transferase from the giant panda parasitic nematode, Baylisascaris schroederi.

PubMed

Xie, Yue; Zhou, Xuan; Chen, Lin; Zhang, Zhihe; Wang, Chengdong; Gu, Xiaobin; Wang, Tao; Peng, Xuerong; Yang, Guangyou

2015-01-23

Baylisascaris schroederi, an intestinal nematode of the giant panda, is the cause of the often fatal disease, baylisascariasis. Glutathione S-transferases (GSTs) are versatile enzymes that can affect parasite survival and parasite-host interactions and, are therefore, potential targets for the development of diagnostic tests and vaccines. In this study, we identified a full-length cDNA that encoded a novel, secretory sigma-like GST (Bsc-GSTσ) from a B. schroederi-omic dataset. Following cloning and sequencing, sequence and structural analyses and comparative modeling were performed using online-bioinformatics and proteomics tools. The recombinant Bsc-GSTσ (rBsc-GSTσ) protein was prokaryotically expressed and then used to detect antigenicity and reactivity using immunoblotting assays. In addition, the native protein in female adult B. schroederi was located via immunofluorescence techniques, while the preliminary ELISA-based serodiagnostic potential of rBsc-GSTσ was assessed in native and infected mouse sera. Bsc-GSTσ contained a 621-bp open reading frame that encoded a polypeptide of 206 amino acids with two typical sigma GST domain profiles, including a GST_N_Sigma_like at the N-terminus and a GST_C_Sigma_like at the C-terminus. The presence of an N-terminal signal sequence indicated that Bsc-GSTσ was a secretory protein. Sequence alignment and phylogenetic analyses showed that Bsc-GSTσ was a nematode-specific member of the Sigma class GSTs and shared the closest genetic distance with its homologue in Ascaris suum. Further comparative structure analyses indicated that Bsc-GSTσ possessed the essential structural motifs (e.g., βαβαββα) and the consensus secondary or tertiary structure that is typical for other characterized GSTσs. Immunolocalization revealed strong distributions of native Bsc-GSTσ in the body hypodermis, lateral chords, gut epithelium, gut microvilli, oviduct epithelium, and ovaries of adult female worms, similar to its homologue in A. suum. Building on good immunogenic properties, rBsc-GSTσ-based ELISA exhibited a sensitivity of 79.1% and a specificity of 82.0% to detect anti-B. schroederi IgG antibodies in the sera of experimentally infected mice. This study presents a comprehensive demonstration of sequence and structural-based analysis of a new, secretory sigma-like GST from a nematode, and its good serodiagnostic performance suggests that rBsc-GSTσ has the potential to detect B. schroederi and, therefore, could be used to develop an ELISA-based serological test to diagnose baylisascariasis in giant pandas.

Feasibility and Acceptability of a Best Supportive Care Checklist among Clinicians.

PubMed

Boucher, Nathan A; Nicolla, Jonathan; Ogunseitan, Adeboye; Kessler, Elizabeth R; Ritchie, Christine S; Zafar, Yousuf Y

2018-04-23

Best supportive care (BSC) is often not standardized across sites, consistent with best evidence, or sufficiently described. We developed a consensus-based checklist to document BSC delivery, including symptom management, decision making, and care planning. We hypothesized that BSC can be feasibly documented with this checklist consistent with consolidated standards of reporting trials. To determine feasibility/acceptability of a BSC checklist among clinicians. To test feasibility of a BSC checklist in standard care, we enrolled a sample of clinicians treating patients with advanced cancer at four centers. Clinicians were asked to complete the checklist at eligible patient encounters. We surveyed enrollees regarding checklist use generating descriptive statistics and frequencies. We surveyed 15 clinicians and 9 advanced practice providers. Mean age was 41 (SD = 7.9). Mean years since fellowship for physicians was 7.2 (SD = 4.5). Represented specialties are medical oncology (n = 8), gynecologic oncology (n = 4), palliative care (n = 2), and other (n = 1). For "overall impact on your delivery of supportive/palliative care," 40% noted improved impact with using BSC. For "overall impact on your documentation of supportive/palliative care," 46% noted improvement. Impact on "frequency of comprehensive symptom assessment" was noted to be "increased" by 33% of providers. None noted decreased frequency or worsening impact on any measure with use of BSC. Regarding feasibility of integrating the checklist into workflow, 73% agreed/strongly agreed that checklists could be easily integrated, 73% saw value in integration, and 80% found it easy to use. Clinicians viewed the BSC checklist favorably illustrating proof of concept, minor workflow impact, and potential of benefit to patients.

Costo Efectividad del Tratamiento de Tumores Neuroendócrinos Pancreáticos Avanzados no Operables con Sunitinib en México.

PubMed

Muciño Ortega, Emilio; Chi-Chan, Alfredo; Peniche-Otero, Gustavo; Gutiérrez-Colín, Consuelo I; Herrera-Rojas, Joaquín; Galindo-Suárez, Rosa María

2012-12-01

Sunitinib had showed a substantial clinical benefit in patients with non-resectable pancreatic Neuroendocrine Tumors (NET). The objective of this study was to estimate the cost-effectiveness of sunitinib in the treatment of non-resectable pancreatic NET, from the perspective of the Social Security Mexican Institute (IMSS). A Markov model (2-week cycles) was used to estimate the health and economic consequences of sunitinib 37.5mg/day+best supportive care (BSC) regarding placebo+BSC (ten-years horizon, discount rate: 5%). Effectiveness measures were: overall survival (OS), progression-free survival (PFS) and quality adjusted life years (QALY). Resource utilization (BSC, adverse events management, medical follow-up) was estimated through a survey with Mexican oncologists (n=10). Unit costs of medication and medical resources were obtained from institutional sources. Sensitivity analyses were performed and acceptability curves were constructed. Sunitinib+BSC gained 0.49 years (PFS), 1.18 years (OS) and 0.70 QALY against placebo+BSC. Sunitinib+BSC increased medical direct costs (2011 US$) per patient in $20,854, which was driven by acquisition costs of sunitinib and medical follow up before progression. ICER's were $42,157, $17,662 and $29,808 per progression-free year, life-year and QALY gained, respectively, which remained robust through±25% changes in main parameters. At willingness to pay higher than $40,000, $22,400 and $37,600 sunitinib+BSC becomes the most cost-effective alternative in regards to PFS, OS and QALYs, respectively. At IMSS, sunitinib+BSC would provide substantial clinical benefits to patients suffering unresectable pancreatic NET, although the latter would increase medical costs of treatment and clinical follow up. Copyright © 2012 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Balanced Scorecards As a Tool for Developing Patient-Centered Pharmacy Services

PubMed Central

Enwere, Emmanuel N.; Keating, Ellen A.; Weber, Robert J.

2014-01-01

Having accurate data is essential for the pharmacy director to manage the department and develop patient-centered pharmacy services. A balanced scorecard (BSC) of essential department data, which is a broad view of a department’s function beyond its financial performance, is an important part of any department’s strategic plan. This column describes how the pharmacy director builds and promotes a department’s BSC. Specifically, this article reviews how the BSC supports the department’s mission and vision, describes the metrics of the BSC and how they are collected, and recommends how the pharmacy director can effectively use the scorecard results in promoting the pharmacy. If designed properly and updated consistently, a BSC can present a broad view of the pharmacy’s performance, serve as a guide for strategic decision making, and improve on the quality of its services. PMID:24958976

Constraining the physical properties of Titan's empty lake basins using nadir and off-nadir Cassini RADAR backscatter

NASA Astrophysics Data System (ADS)

Michaelides, R. J.; Hayes, A. G.; Mastrogiuseppe, M.; Zebker, H. A.; Farr, T. G.; Malaska, M. J.; Poggiali, V.; Mullen, J. P.

2016-05-01

We use repeat synthetic aperture radar (SAR) observations and complementary altimetry passes acquired by the Cassini spacecraft to study the scattering properties of Titan's empty lake basins. The best-fit coefficients from fitting SAR data to a quasi-specular plus diffuse backscatter model suggest that the bright basin floors have a higher dielectric constant, but similar facet-scale rms surface facet slopes, to surrounding terrain. Waveform analysis of altimetry returns reveals that nadir backscatter returns from basin floors are greater than nadir backscatter returns from basin surroundings and have narrower pulse widths. This suggests that floor deposits are structurally distinct from their surroundings, consistent with the interpretation that some of these basins may be filled with evaporitic and/or sedimentary deposits. Basin floor deposits also express a larger diffuse component to their backscatter, which is likely due to variations in subsurface structure or an increase in roughness at the wavelength scale (Hayes, A.G. et al. [2008]. Geophys. Res. Lett. 35, 9). We generate a high-resolution altimetry radargram of the T30 altimetry pass over an empty lake basin, with which we place geometric constraints on the basin's slopes, rim heights, and depth. Finally, the importance of these backscatter observations and geometric measurements for basin formation mechanisms is briefly discussed.

COSMO-SkyMed Image Investigation of Snow Features in Alpine Environment

PubMed Central

Paloscia, Simonetta; Pettinato, Simone; Santi, Emanuele; Valt, Mauro

2017-01-01

In this work, X band images acquired by COSMO-SkyMed (CSK) on alpine environment have been analyzed for investigating snow characteristics and their effect on backscattering variations. Preliminary results confirmed the capability of simultaneous optical and Synthetic Aperture Radar (SAR) images (Landsat-8 and CSK) in separating snow/no-snow areas and in detecting wet snow. The sensitivity of backscattering to snow depth has not always been confirmed, depending on snow characteristics related to the season. A model based on Dense Media Radiative Transfer theory (DMRT-QMS) was applied for simulating the backscattering response on the X band from snow cover in different conditions of grain size, snow density and depth. By using DMRT-QMS and snow in-situ data collected on Cordevole basin in Italian Alps, the effect of grain size and snow density, beside snow depth and snow water equivalent, was pointed out, showing that the snow features affect the backscatter in different and sometimes opposite ways. Experimental values of backscattering were correctly simulated by using this model and selected intervals of ground parameters. The relationship between simulated and measured backscattering for the entire dataset shows slope >0.9, determination coefficient, R2 = 0.77, and root mean square error, RMSE = 1.1 dB, with p-value <0.05. PMID:28054962

Tropospheric temperature measurements using a rotational raman lidar

NASA Astrophysics Data System (ADS)

Lee, Robert Benjamin, III

Using the Hampton University (HU) Mie and Raman lidar, tropospheric temperature profiles were inferred from lidar measurements of anti-Stokes rotational Raman (RR) backscattered laser light from atmospheric nitrogen and oxygen molecules. The molecules were excited by 354.7 nanometer (nm) laser light emitted by the HU lidar. Averaged over 60-minute intervals, RR backscattered signals were detected in narrow 353.35 nm and 354.20 nm spectral bands with full-widths-at-half-maxima (FWHM) of 0.3 nm. During the special April 19-30, 2012, Ground-Based Remote Atmospheric Sounding Program (GRASP) campaign, the lidar temperature calibration coefficients were empirically derived using linear least squares and second order polynomial analyses of the lidar backscattered RR signals and of reference temperature profiles, obtained from radiosondes. The GRASP radiosondes were launched within 400 meters of the HU lidar site. Lidar derived temperature profiles were obtained at altitudes from the surface to over 18 kilometers (km) at night, and up to 5 km during the day. Using coefficients generated from least squares analyses, nighttime profiles were found to agree with profiles from reference radiosonde measurements within 3 K, at altitudes between 4 km and 9 km. Coefficients generated from the second order analyses yielded profiles which agreed with the reference profiles within 1 K uncertainty level in the 4 km to 10 km altitude region. Using profiles from GRASP radiosondes, the spatial and temporal homogeneities of the atmosphere, over HU, were estimated at the 1.5 K level within a 10 km radius of HU, and for observational periods approaching 3 hours. Theoretical calibration coefficients were derived from the optical and physical properties of the HU RR lidar and from the spectroscopic properties of atmospheric molecular nitrogen and oxygen. The theoretical coefficients along with lidar measurements of sky background radiances were used to evaluate the temporal stability of the empirically derived temperature profiles from the RR lidar measurements. The evaluations revealed systematic drifts in the coefficients. Frequent reference radiosonde temperature profiles should be used to correct for the drifts in the coefficients. For the first time, the cause of the coefficient drifts has been identified as the differences in the aging of the spectral responses of the HU lidar detector pairs. For the first time, the use of lidar sky background measurements was demonstrated as a useful technique to correct for the coefficient drift. This research should advance the derivations of lidar temperature calibration coefficients which can be used for long observational periods of temperature fields without the need for frequent lidar calibrations using radiosondes.

CALIOP near-real-time backscatter products compared to EARLINET data

NASA Astrophysics Data System (ADS)

Grigas, T.; Hervo, M.; Gimmestad, G.; Forrister, H.; Schneider, P.; Preißler, J.; Tarrason, L.; O'Dowd, C.

2015-11-01

The expedited near-real-time Level 1.5 Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) version 3 products were evaluated against data from the ground-based European Aerosol Research Lidar Network (EARLINET). The statistical framework and results of the three-year evaluation of 48 CALIOP overpasses with ground tracks within a 100 km distance from operating EARLINET stations are presented and include analysis for the following CALIOP classifications of aerosol type: dust, polluted dust, clean marine, clean continental, polluted continental, mixed and/or smoke/biomass burning. For the complete data set comprising both the planetary boundary layer (PBL) and the free troposphere (FT) data, the correlation coefficient (R) was 0.86. When the analysis was conducted separately for the PBL and FT, the correlation coefficients were R = 0.6 and R = 0.85, respectively. From analysis of selected specific cases, it was initially thought that the presence of FT layers, with high attenuated backscatter, led to poor agreement of the PBL backscatter profiles between the CALIOP and EARLINET and prompted a further analysis to filter out such cases; however, removal of these layers did not improve the agreement as R reduced marginally from R = 0.86 to R = 0.84 for the combined PBL and FT analysis, increased marginally from R = 0.6 up to R = 0.65 for the PBL on its own, and decreased marginally from R = 0.85 to R = 0.79 for the FT analysis on its own. This suggests considerable variability, across the data set, in the spatial distribution of the aerosol over spatial scales of 100 km or less around some EARLINET stations rather than influence from elevated FT layers. For specific aerosol types, the correlation coefficient between CALIOP backscatter profiles and the EARLINET data ranged from R = 0.37 for polluted continental aerosol in the PBL to R = 0.57 for dust in the FT.

Aerosol and Cloud Interaction Observed From High Spectral Resolution Lidar Data

NASA Technical Reports Server (NTRS)

Su, Wenying; Schuster, Gregory L.; Loeb, Norman G.; Rogers, Raymond R.; Ferrare, Richard A.; Hostetler, Chris A.; Hair, Johnathan W.; Obland, Michael D.

2008-01-01

Recent studies utilizing satellite retrievals have shown a strong correlation between aerosol optical depth (AOD) and cloud cover. However, these retrievals from passive sensors are subject to many limitations, including cloud adjacency (or 3D) effects, possible cloud contamination, uncertainty in the AOD retrieval. Some of these limitations do not exist in High Spectral Resolution Lidar (HSRL) observations; for instance, HSRL observations are not a ected by cloud adjacency effects, are less prone to cloud contamination, and offer accurate aerosol property measurements (backscatter coefficient, extinction coefficient, lidar ratio, backscatter Angstrom exponent,and aerosol optical depth) at a neospatial resolution (less than 100 m) in the vicinity of clouds. Hence, the HSRL provides an important dataset for studying aerosol and cloud interaction. In this study, we statistically analyze aircraft-based HSRL profiles according to their distance from the nearest cloud, assuring that all profile comparisons are subject to the same large-scale meteorological conditions. Our results indicate that AODs from HSRL are about 17% higher in the proximity of clouds (approximately 100 m) than far away from clouds (4.5 km), which is much smaller than the reported cloud 3D effect on AOD retrievals. The backscatter and extinction coefficients also systematically increase in the vicinity of clouds, which can be explained by aerosol swelling in the high relative humidity (RH) environment and/or aerosol growth through in cloud processing (albeit not conclusively). On the other hand, we do not observe a systematic trend in lidar ratio; we hypothesize that this is caused by the opposite effects of aerosol swelling and aerosol in-cloud processing on the lidar ratio. Finally, the observed backscatter Angstrom exponent (BAE) does not show a consistent trend because of the complicated relationship between BAE and RH. We demonstrate that BAE should not be used as a surrogate for Angstrom exponent, especially at high RH.

78 FR 40744 - Request for Nominations of Candidates To Serve on the Board of Scientific Counselors (BSC...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-08

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Request for Nominations of Candidates To Serve on the Board of Scientific Counselors (BSC), Office of Infectious Diseases (OID) The Centers for Disease Control and Prevention (CDC) is soliciting nominations for possible membership on the BSC, OID. This board...

A management approach that drives actions strategically: balanced scorecard in a mental health trust case study.

PubMed

Schmidt, Stefan; Bateman, Ian; Breinlinger-O'Reilly, Jochen; Smith, Peter

2006-01-01

Achieving excellence is a current preoccupation in U.K. public health organisations. This article aims to use a case study to explain how a mental health trust delivers excellent performance using a balanced scorecard (BSC) management approach. Reports a project to implement a BSC approach in the South West Yorkshire Mental Health NHS Trust to achieve its "excellence" objectives. The authors were participants in the project. The design of the pilot project was informed theoretically by the work of Kaplan and Norton and practically by in-house discussions on a strategy to achieve excellence. Explains the process of building a BSC strategy step-by-step. Discusses how the vision and strategies of a mental health trust can be translated into tangible measures, which are the basis for actions that are driven strategically. There are many possibilities for a BSC management approach and this case study is specific to mental health trusts in the UK, although it is believed that the case has a universally applicable modus operandi. This article will help healthcare managers to evaluate the benefits of a BSC management approach. This article explains how actions can be structured in connection with a BSC management approach.

Polarization lidar for atmospheric monitoring

NASA Astrophysics Data System (ADS)

Liu, Qiaojun; Wu, Chengxuan; Yuk Sun Cheng, Andrew; Wang, Zhangjun; Meng, Xiangqian; Chen, Chao; Li, Xianxin; Liu, Xingtao; Zhang, Hao; Zong, Fangyi

2018-04-01

Aerosol plays an important role in global climate and weather changes. Polarization lidar captures parallel and perpendicular signals from atmosphere to research aerosols. The lidar system we used has three emission wavelengths and could obtain the atmospheric aerosol extinction coefficient, backscattering coefficient and depolarization ratio. In this paper, the design of the lidar is described. The methods of data acquisition and inversion are given. Some recent results are presented.

Long-term variability of aerosol optical properties and radiative effects in Northern Finland

NASA Astrophysics Data System (ADS)

Lihavainen, Heikki; Hyvärinen, Antti; Asmi, Eija; Hatakka, Juha; Viisanen, Yrjö

2017-04-01

We introduce long term dataset of aerosol scattering and absorption properties and combined aerosol optical properties measured in Pallas Atmosphere-Ecosystem Supersite in Norhern Finland. The station is located 170 km north of the Arctic Circle. The station is affected by both pristine Arctic air masses as well as long transported air pollution from northern Europe. We studied the optical properties of aerosols and their radiative effects in continental and marine air masses, including seasonal cycles and long-term trends. The average (median) scattering coefficient, backscattering fraction, absorption coefficient and single scattering albedo at the wavelength of 550 nm were 7.9 (4.4) 1/Mm, 0.13 (0.12), 0.74 (0.35) 1/Mm and 0.92 (0.93), respectively. We observed clear seasonal cycles in these variables, the scattering coefficient having high values during summer and low in fall, and absorption coefficient having high values during winter and low in fall. We found that the high values of the absorption coefficient and low values of the single scattering albedo were related to continental air masses from lower latitudes. These aerosols can induce an additional effect on the surface albedo and melting of snow. We observed the signal of the Arctic haze in marine (northern) air masses during March and April. The haze increased the value of the absorption coefficient by almost 80% and that of the scattering coefficient by about 50% compared with the annual-average values. We did not observe any long-term trend in the scattering coefficient, while our analysis showed a clear decreasing trend in the backscattering fraction and scattering Ångström exponent during winter. We also observed clear relationship with temperature and aerosol scattering coefficient. We will present also how these different features affects to aerosol direct radiative forcing.

The 48-inch lidar aerosol measurements taken at the Langley Research Center

NASA Technical Reports Server (NTRS)

Woods, David C.; Osborn, M. T.; Winker, D. M.; Decoursey, R. J.; Youngbluth, Otto, Jr.

1994-01-01

This report presents lidar data taken between July 1991 and December 1992 using a ground-based 48-inch lidar instrument at the Langley Research Center in Hampton, Virginia. Seventy lidar profiles (approximately one per week) were obtained during this period, which began less than 1 month after the eruption of the Mount Pinatubo volcano in the Philippines. Plots of backscattering ratio as a function of altitude are presented for each data set along with tables containing numerical values of the backscattering ratio and backscattering coefficient versus altitude. The enhanced aerosol backscattering seen in the profiles highlights the influence of the Mount Pinatubo eruption on the stratospheric aerosol loading over Hampton. The long-term record of the profiles gives a picture of the evolution of the aerosol cloud, which reached maximum loading approximately 8 months after the eruption and then started to decrease gradually. NASA RP-1209 discusses 48-inch lidar aerosol measurements taken at the Langley Research Center from May 1974 to December 1987.

Monte Carlo study of backscattering of. beta. rays from various monoatomic slabs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pandey, L. N.; Rustgi, M. L.

1989-07-01

A Monte Carlo study of the backscattering coefficients and backscatteringintensity of ..beta.. rays from /sup 204/ Tl and /sup 90/ Y sources from slabs of Al,Cu, Sn, Tb, and Pb of different thicknesses is carried out. The results forangles of incidence 0/degree/, 30/degree/, 45/degree/, and 60/degree/ and absorber thicknesses of 3,5, 10, 15, 30, and 50 mg/cm/sup 2/ for /sup 204/ Tl ..beta.. rays and thicknesses of3, 5, 10, 20, 50, 100, 150, and 190 mg/cm/sup 2/ for /sup 90/ Y ..beta.. rays aregiven in tabular form. On using normalization factors good agreement with themeasurements of Sharma and Singh ismore » obtained. A phenomenological attempt toinvestigate a relationship between the backscatter intensity and atomic number/ital Z/ of the backscatterer indicates that the backscattered intensity is alinear function of ln /ital Z/(/ital Z/+1). A partial theoretical justification forthis relationship is given.« less

Characterization of trabecular bone using the backscattered spectral centroid shift.

PubMed

Wear, Keith A

2003-04-01

Ultrasonic attenuation in bone in vivo is generally measured using a through-transmission method at the calcaneus. Although attenuation in calcaneus has been demonstrated to be a useful predictor for osteoporotic fracture risk, measurements at other clinically important sites, such as hip and spine, could potentially contain additional useful diagnostic information. Through-transmission measurements may not be feasible at these sites due to complex bone shapes and the increased amount of intervening soft tissue. Centroid shift from the backscattered signal is an index of attenuation slope and has been used previously to characterize soft tissues. In this paper, centroid shift from signals backscattered from 30 trabecular bone samples in vitro were measured. Attenuation slope also was measured using a through-transmission method. The correlation coefficient between centroid shift and attenuation slope was -0.71. The 95% confidence interval was (-0.86, -0.47). These results suggest that the backscattered spectral centroid shift may contain useful diagnostic information potentially applicable to hip and spine.

New Examination of the Traditional Raman Lidar Technique II: Temperature Dependence Aerosol Scattering Ratio and Water Vapor Mixing Ratio Equations

NASA Technical Reports Server (NTRS)

Whiteman, David N.; Abshire, James B. (Technical Monitor)

2002-01-01

In a companion paper, the temperature dependence of Raman scattering and its influence on the Raman water vapor signal and the lidar equations was examined. New forms of the lidar equation were developed to account for this temperature sensitivity. Here we use those results to derive the temperature dependent forms of the equations for the aerosol scattering ratio, aerosol backscatter coefficient, extinction to backscatter ratio and water vapor mixing ratio. Pertinent analysis examples are presented to illustrate each calculation.

A feasibility study for a remote laser water turbidity meter

NASA Technical Reports Server (NTRS)

Hickman, G. D.; Ghovanlou, A. H.; Friedman, E. J.; Gault, C. S.; Hogg, J. E.

1974-01-01

A technique to remotely determine the attenuation coefficient (alpha) of the water was investigated. The backscatter energy (theta = 180 deg) of a pulse laser (lambda = 440 - 660 nm) was found directly related to the water turbidity. The greatest sensitivity was found to exist at 440 nm. For waters whose turbidity was adjusted using Chesapeake Bay sediment, the sensitivity in determining alpha at 440 nm was found to be approximately 5 - 10%. A correlation was also found to exist between the water depth (time) at which the peak backscatter occurs and alpha.

Applications of interferometrically derived terrain slopes: Normalization of SAR backscatter and the interferometric correlation coefficient

NASA Technical Reports Server (NTRS)

Werner, Charles L.; Wegmueller, Urs; Small, David L.; Rosen, Paul A.

1994-01-01

Terrain slopes, which can be measured with Synthetic Aperture Radar (SAR) interferometry either from a height map or from the interferometric phase gradient, were used to calculate the local incidence angle and the correct pixel area. Both are required for correct thematic interpretation of SAR data. The interferometric correlation depends on the pixel area projected on a plane perpendicular to the look vector and requires correction for slope effects. Methods for normalization of the backscatter and interferometric correlation for ERS-1 SAR are presented.

Study of diffusion of indocyanine green as a photodynamic dye into skin using backscattering spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Genina, E A; Bashkatov, A N; Tuchin, V V

One of the lines of development of modern medicine is theranostics consisting in simultaneous diagnosis and laser treatment with the use of multifunctional agents such as fluorescent indocyanine green that has photodynamic and photothermal properties. Diffusion of indocyanine green dissolved in water and aqueous solutions of alcohols (glycerol, propylene glycol and ethanol) into the dermis is studied by using backscattering spectroscopy. The coefficients of the dye diffusion into the dermis are obtained for the first time by using these solvents. (laser biophotonics)

Oil film thickness measurement using airborne laser-induced water Raman backscatter

NASA Technical Reports Server (NTRS)

Hoge, F. E.; Swift, R. N.

1980-01-01

The use of laser-induced water Raman backscatter for remote thin oil film detection and thickness measurement is reported here for the first time. A 337.1-nm nitrogen laser was used to excite the 3400-cm-1 OH stretch band of natural ocean water beneath the oil slick from an altitude of 150 m. The signal strength of the 381-nm water Raman backscatter was always observed to depress when the oil was encountered and then return to its original undepressed value after complete aircraft traversal of the floating slick. After removal of background and oil fluorescence contributions, the ratio of the depressed-to-undepressed airborne water Raman signal intensities, together with laboratory measured oil extinction coefficients, is used to calculate the oil film thickness.

Criteria of backscattering in chiral one-way photonic crystals

NASA Astrophysics Data System (ADS)

Cheng, Pi-Ju; Chang, Shu-Wei

2016-03-01

Optical isolators are important devices in photonic circuits. To reduce the unwanted reflection in a robust manner, several setups have been realized using nonreciprocal schemes. In this study, we show that the propagating modes in a strongly-guided chiral photonic crystal (no breaking of the reciprocity) are not backscattering-immune even though they are indeed insensitive to many types of scatters. Without the protection from the nonreciprocity, the backscattering occurs under certain circumstances. We present a perturbative method to calculate the backscattering of chiral photonic crystals in the presence of chiral/achiral scatters. The model is, essentially, a simplified analogy to the first-order Born approximation. Under reasonable assumptions based on the behaviors of chiral photonic modes, we obtained the expression of reflection coefficients which provides criteria for the prominent backscattering in such chiral structures. Numerical examinations using the finite-element method were also performed and the results agree well with the theoretical prediction. From both our theory and numerical calculations, we find that the amount of backscattering critically depends on the symmetry of scatter cross sections. Strong reflection takes place when the azimuthal Fourier components of scatter cross sections have an order l of 2. Chiral scatters without these Fourier components would not efficiently reflect the chiral photonic modes. In addition, for these chiral propagating modes, disturbances at the most significant parts of field profiles do not necessarily result in the most effective backscattering. The observation also reveals what types of scatters or defects should be avoided in one-way applications of chiral structures in order to minimize the backscattering.

Alignment of University Information Technology Resources with the Malcolm Baldrige Results Criteria for Performance Excellence in Education: A Balanced Scorecard Approach

ERIC Educational Resources Information Center

Beard, Deborah F.; Humphrey, Roberta L.

2014-01-01

The authors suggest using a balanced scorecard (BSC) approach to evaluate information technology (IT) resources in higher education institutions. The BSC approach illustrated is based on the performance criteria of the Malcolm Baldrige National Quality Award in Education. This article suggests areas of potential impact of IT on BSC measures in…

The dose from Compton backscatter screening.

PubMed

Rez, Peter; Metzger, Robert L; Mossman, Kenneth L

2011-04-01

Systems based on the detection of Compton backscattered X rays have been deployed for screening personnel for weapons and explosives. Similar principles are used for screening vehicles at border-crossing points. Based on well-established scattering cross sections and absorption coefficients in conjunction with reasonable estimates of the image contrast and resolution, the entrance skin dose and the dose at a depth of 1 cm can be calculated. The effective dose can be estimated using the same conversion coefficients as used to convert exposure measurements to the effective dose. It is shown that the effective dose is highly dependent on image resolution (i.e. pixel size).The effective doses for personnel screening systems are unlikely to be in compliance with the American National Standards Institute standard NS 43.17 unless the pixel sizes are >4 mm. Nevertheless, calculated effective doses are well below doses associated with health effects.

Properties of the Water Column and Bottom Derived from AVIRIS Data

NASA Technical Reports Server (NTRS)

Lee, Zhong-Ping; Carder, Kendall L.; Chen, F. Robert; Peacock, Thomas G.

2001-01-01

Using AVIRIS data as an example, we show in this study that the optical properties of the water column and bottom of a large, shallow area can be adequately retrieved using a model-driven optimization technique. The simultaneously derived properties include bottom depth, bottom albedo, and water absorption and backscattering coefficients, which in turn could be used to derive concentrations of chlorophyll, dissolved organic matter, and suspended sediments. The derived bottom depths were compared with a bathymetry chart and a boat survey and were found to agree very well. Also, the derived bottom-albedo image shows clear spatial patterns, with end members consistent with sand and seagrass. The image of absorption and backscattering coefficients indicates that the water is quite horizontally mixed. These results suggest that the model and approach used work very well for the retrieval of sub-surface properties of shallow-water environments even for rather turbid environments like Tampa Bay, Florida.

A mixed multiscale model better accounting for the cross term of the subgrid-scale stress and for backscatter

NASA Astrophysics Data System (ADS)

Thiry, Olivier; Winckelmans, Grégoire

2016-02-01

In the large-eddy simulation (LES) of turbulent flows, models are used to account for the subgrid-scale (SGS) stress. We here consider LES with "truncation filtering only" (i.e., that due to the LES grid), thus without regular explicit filtering added. The SGS stress tensor is then composed of two terms: the cross term that accounts for interactions between resolved scales and unresolved scales, and the Reynolds term that accounts for interactions between unresolved scales. Both terms provide forward- (dissipation) and backward (production, also called backscatter) energy transfer. Purely dissipative, eddy-viscosity type, SGS models are widely used: Smagorinsky-type models, or more advanced multiscale-type models. Dynamic versions have also been developed, where the model coefficient is determined using a dynamic procedure. Being dissipative by nature, those models do not provide backscatter. Even when using the dynamic version with local averaging, one typically uses clipping to forbid negative values of the model coefficient and hence ensure the stability of the simulation; hence removing the backscatter produced by the dynamic procedure. More advanced SGS model are thus desirable, and that better conform to the physics of the true SGS stress, while remaining stable. We here investigate, in decaying homogeneous isotropic turbulence, and using a de-aliased pseudo-spectral method, the behavior of the cross term and of the Reynolds term: in terms of dissipation spectra, and in terms of probability density function (pdf) of dissipation in physical space: positive and negative (backscatter). We then develop a new mixed model that better accounts for the physics of the SGS stress and for the backscatter. It has a cross term part which is built using a scale-similarity argument, further combined with a correction for Galilean invariance using a pseudo-Leonard term: this is the term that also does backscatter. It also has an eddy-viscosity multiscale model part that accounts for all the remaining phenomena (also for the incompleteness of the cross term model), that is dynamic and that adjusts the overall dissipation. The model is tested, both a priori and a posteriori, and is compared to the direct numerical simulation and to the exact SGS terms, also in time. The model is seen to provide accurate energy spectra, also in comparison to the dynamic Smagorinsky model. It also provides significant backscatter (although four times less than the real SGS stress), while remaining stable.

Developing and using a balanced scorecard: a case study with SWOT analysis.

PubMed

Gumbus, Andra; Lussier, Robert N

2003-01-01

Have you tried to measure your laboratory's performance lately? Do you measure and assess financial results, customer satisfaction, internal process efficiency, and learning and growth? If any of these metrics are missing from your performance measurement system, you are not using the latest management tool that is sweeping the health-care industry--the balanced scorecard (BSC). This article begins with a discussion of the BSC and why you should use it in your laboratory, followed by SWOT analysis to assess the strengths, weaknesses, opportunities, and threats (SWOT) a BSC offers your laboratory. A laboratory case study is then presented to assist you in developing and using a BSC in your laboratory.

News from the Biological Stain Commission.

PubMed

Lyon, H O; Kiernan, J A

2008-12-01

In the three earlier editions of News from the Biological Stain Commission (BSC), under the heading of "Regulatory affairs," the BSC's International Affairs Committee reported on the work of Technical Committee 212, Clinical Laboratory Testing and in Vitro Diagnostic Test Systems of the International Standards Organization (ISO/TC 212) and its working groups, WG 1, WG 2 and WG 3. In this issue of News from the BSC, H.O. Lyon provides information from the annual meeting of ISO/TC 212 that took place June 2-4, 2008 in Vancouver, British Columbia, Canada. In addition, under the heading of "Certification," J.A. Kiernan examines the certification procedure for thionine used by the BSC laboratory in Rochester, NY.

An Examination of Interprofessional Team Functioning in a BScN Blended Learning Program: Implications for Accessible Distance-Based Nursing Education Programs

ERIC Educational Resources Information Center

Carter, Lorraine Mary; Beattie, Bev; Caswell, Wenda; Fitzgerald, Scott; Nowrouzi, Behdin

2016-01-01

In this study, the perceptions and experiences of an interprofessional team responsible for the development and delivery of the Registered Practical Nurse (RPN) to Bachelor of Science in Nursing (BScN) Blended Learning Program at Nipissing University were examined. In this program, RPNs can acquire a BScN through distance-based part-time study,…

Modification of gray iron produced by induction melting with barium strontium

NASA Astrophysics Data System (ADS)

Modzelevskaya, G.; Feoktistov, A. V.; Selyanin, I. F.; Kutsenko, A. I.; Kutsenko, A. A.

2016-09-01

The article provides analysis of results of gray iron experimental melts in induction furnace and the following melt modification with barium-strontium carbonate (BSC-2). It is shown that modification positively affects mechanical and casting properties and as-cast iron structure. It was established that BSC-2 granulated immediately prior to use has greater impact on melt than BSC-2 of the same faction, supplied by the manufacturer.

A novel binary shape context for 3D local surface description

NASA Astrophysics Data System (ADS)

Dong, Zhen; Yang, Bisheng; Liu, Yuan; Liang, Fuxun; Li, Bijun; Zang, Yufu

2017-08-01

3D local surface description is now at the core of many computer vision technologies, such as 3D object recognition, intelligent driving, and 3D model reconstruction. However, most of the existing 3D feature descriptors still suffer from low descriptiveness, weak robustness, and inefficiency in both time and memory. To overcome these challenges, this paper presents a robust and descriptive 3D Binary Shape Context (BSC) descriptor with high efficiency in both time and memory. First, a novel BSC descriptor is generated for 3D local surface description, and the performance of the BSC descriptor under different settings of its parameters is analyzed. Next, the descriptiveness, robustness, and efficiency in both time and memory of the BSC descriptor are evaluated and compared to those of several state-of-the-art 3D feature descriptors. Finally, the performance of the BSC descriptor for 3D object recognition is also evaluated on a number of popular benchmark datasets, and an urban-scene dataset is collected by a terrestrial laser scanner system. Comprehensive experiments demonstrate that the proposed BSC descriptor obtained high descriptiveness, strong robustness, and high efficiency in both time and memory and achieved high recognition rates of 94.8%, 94.1% and 82.1% on the considered UWA, Queen, and WHU datasets, respectively.

An analytical two-flow model to simulate the distribution of irradiance in coastal waters with a wind-roughed surface and bottom reflectance

NASA Astrophysics Data System (ADS)

Ma, Wei-Ming

1997-06-01

An analytical two-flow model is derived from the radiative transfer equation to simulate the distribution of irradiance in coastal waters with a wind-roughed surface and bottom reflectance. The model utilizes unique boundary conditions, including the surface slope of the downwelling and upwelling irradiance as well as the influence of wind and bottom reflectance on simulated surface reflectance. The developed model provides a simple mathematical concept for understanding the irradiant light flux and associated processes in coastal or fresh water as well as turbid estuarine waters. The model is applied to data from the Banana River and coastal Atlantic Ocean water off the east coast of central Florida, USA. The two-flow irradiance model is capable of simulating realistic above-surface reflectance signatures under wind-roughened air-water surface given realistic input parameters including a specular flux conversion coefficient, absorption coefficient, backscattering coefficient, atmospheric visibility, bottom reflectance, and water depth. The root-mean-squared error of the calculated above-surface reflectances is approximately 3% in the Banana River and is less than 15% in coastal Atlantic Ocean off the east of Florida. Result of the subsurface reflectance sensitivity analysis indicates that the specular conversion coefficient is the most sensitive parameter in the model, followed by the beam attenuation coefficient, absorption coefficient, water depth, backscattering coefficient, specular irradiance, diffuse irradiance, bottom reflectance, and wind speed. On the other hand, result of the above-surface reflectance sensitivity analysis indicates that the wind speed is the most important parameter, followed by bottom reflectance, attenuation coefficient, water depth, conversion coefficient, specular irradiance, downwelling irradiance, absorption coefficient, and backscattering coefficient. Model results depend on the accuracy of these parameters to a large degree and more important the water depth and value of the bottom reflectance. The results of this work indicates little change of subsurface or in-water reflectances, due to variations of wind speed and observation angle. Simulations of the wind effect on the total downwelling irradiance from the two- flow model indicates that the total downwelling irradiance just below a wind-roughened water surface increases to about 1% of the total downwelling irradiance on a calm water surface when the sun is near zenith and increases to about 3% when the sun is near the horizon. This analytically based model, solved or developed utilizing the unique boundary conditions, can be applied to remote sensing of oceanic upper mixed layer dynamics, plant canopies, primary production, and shallow water environments with different bottom type reflectances. Future applications may include determining effects of sediment resuspension of bottom sediments in the bottom boundary layer on remotely sensed data.

Cost-effectiveness of maintenance pemetrexed in patients with advanced nonsquamous-cell lung cancer from the perspective of the Swiss health care system.

PubMed

Matter-Walstra, Klazien; Joerger, Markus; Kühnel, Ursula; Szucs, Thomas; Pestalozzi, Bernhard; Schwenkglenks, Matthias

2012-01-01

A recent randomized study showed switch maintenance with pemetrexed after nonpemetrexed-containing first-line chemotherapy in patients with advanced nonsmall-cell lung cancer to prolong overall survival by 2.8 months. We examined the cost-effectiveness of pemetrexed in this indication, from the perspective of the Swiss health care system, and assessed the influence of the costs of best supportive care (BSC) on overall cost-effectiveness. A Markov model was constructed based on the pemetrexed maintenance study, and the incremental cost-effectiveness ratio (ICER) of adding pemetrexed until disease progression was calculated as cost per quality-adjusted life-year gained. Uncertainties concerning the costs of BSC on the ICER were addressed. The base case ICER for maintenance therapy with pemetrexed plus BSC compared to BSC alone was €106,202 per quality-adjusted life-year gained. Varying the costs for BSC had a marked effect. Assuming a reduction of the costs for BSC by 25% in the pemetrexed arm resulted in an ICER of €47,531 per quality-adjusted life-year, which is below predefined criteria for cost effectiveness in Switzerland. Switch maintenance with pemetrexed in patients with advanced nonsquamous-cell lung cancer after standard first-line chemotherapy is not cost-effective. Uncertainties on the resource use and costs for BSC have a large influence on the cost-effectiveness calculation and should be reported in more detail. Copyright © 2012 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Validation of cross-contamination control in biological safety cabinet for biotech/pharmaceutical manufacturing process.

PubMed

Hu, Shih-Cheng; Shiue, Angus; Tu, Jin-Xin; Liu, Han-Yang; Chiu, Rong-Ben

2015-12-01

For class II, type A2 biological safety cabinets (BSC), NSF/ANSI Standard 49 should be conformed in cabinet airflow velocity derivation, particle contamination, and aerodynamic flow properties. However, there exists a potential problem. It has been built that the cabinet air flow stabilize is influenced by the quantity of downflow of air and the height above the cabinet exhaust opening. Three air downflow quantities were compared as an operating apparatus was placed from 20 to 40 cm above the bench of the cabinet. The results show that the BSC air downflow velocity is a function of increased sampling height, displaying that containment is improvingly permitted over product protection as the sampling height decreases. This study investigated the concentration gradient of particles at various heights and downflow air quantity from the bench of the BSC. Experiment results indicate that performance near the bench was better than in the rest of the BSC. In terms of height, the best cleanliness was measured at a height of 10 cm over the bench; it reduced actually with add in height. The empirical curves accommodate, founded on the concentration gradient of particle created was elaborated for evaluating the particle concentration at different heights and downflow air quantity from the source of the bench of the BSC. The particle image velocimetry system applied for BSC airflow research to fix amount of airflow patterns and air distribution measurement and results of measurements show how obstructions can greatly influence the airflow and contaminant transportation in a BSC.

Robust diffraction correction method for high-frequency ultrasonic tissue characterization

NASA Astrophysics Data System (ADS)

Raju, Balasundar

2004-05-01

The computation of quantitative ultrasonic parameters such as the attenuation or backscatter coefficient requires compensation for diffraction effects. In this work a simple and accurate diffraction correction method for skin characterization requiring only a single focal zone is developed. The advantage of this method is that the transducer need not be mechanically repositioned to collect data from several focal zones, thereby reducing the time of imaging and preventing motion artifacts. Data were first collected under controlled conditions from skin of volunteers using a high-frequency system (center frequency=33 MHz, BW=28 MHz) at 19 focal zones through axial translation. Using these data, mean backscatter power spectra were computed as a function of the distance between the transducer and the tissue, which then served as empirical diffraction correction curves for subsequent data. The method was demonstrated on patients patch-tested for contact dermatitis. The computed attenuation coefficient slope was significantly (p<0.05) lower at the affected site (0.13+/-0.02 dB/mm/MHz) compared to nearby normal skin (0.2+/-0.05 dB/mm/MHz). The mean backscatter level was also significantly lower at the affected site (6.7+/-2.1 in arbitrary units) compared to normal skin (11.3+/-3.2). These results show diffraction corrected ultrasonic parameters can differentiate normal from affected skin tissues.

Influence of microarchitecture alterations on ultrasonic backscattering in an experimental simulation of bovine cancellous bone aging.

PubMed

Apostolopoulos, K N; Deligianni, D D

2008-02-01

An experimental model which can simulate physical changes that occur during aging was developed in order to evaluate the effects of change of mineral content and microstructure on ultrasonic properties of bovine cancellous bone. Timed immersion in hydrochloric acid was used to selectively alter the mineral content. Scanning electron microscopy and histological staining of the acid-treated trabeculae demonstrated a heterogeneous structure consisting of a mineralized core and a demineralized layer. The presence of organic matrix contributed very little to normalized broadband ultrasound attenuation (nBUA) and speed of sound. All three ultrasonic parameters, speed of sound, nBUA and backscatter coefficient, were sensitive to changes in apparent density of bovine cancellous bone. A two-component model utilizing a combination of two autocorrelation functions (a densely populated model and a spherical distribution) was used to approximate the backscatter coefficient. The predicted attenuation due to scattering constituted a significant part of the measured total attenuation (due to both scattering and absorption mechanisms) for bovine cancellous bone. Linear regression, performed between trabecular thickness values and estimated from the model correlation lengths, showed significant linear correlation, with R(2)=0.81 before and R(2)=0.80 after demineralization. The accuracy of estimation was found to increase with trabecular thickness.

LIDAR detection of forest fire smoke above Sofia

NASA Astrophysics Data System (ADS)

Grigorov, Ivan; Deleva, Atanaska; Stoyanov, Dimitar; Kolev, Nikolay; Kolarov, Georgi

2015-01-01

The distribution of aerosol load in the atmosphere due to two forest fires near Sofia (the capital city of Bulgaria) was studied using two aerosol lidars which operated at 510.6 nm and 1064 nm. Experimental data is presented as 2D-heatmaps of the evolution of attenuated backscatter coefficient profiles and mean profile of the aerosol backscatter coefficient, calculated for each lidar observation. Backscatter related Angstrom exponent was used as a criterion in particle size estimation of detected smoke layers. Calculated minimal values at altitudes where the aerosol layer was observed corresponded to predominant fraction of coarse aerosol. Dust-transport forecast maps and calculations of backward trajectories were employed to make conclusions about aerosol's origin. They confirmed the local transport of smoke aerosol over the city and lidar station. DREAM forecast maps predicted neither cloud cover, nor Saharan load in the air above Sofia on the days of measurements. The results of lidar observations are discussed in conjunction with meteorological situation, aiming to better explain the reason for the observed aerosol stratification. The data of regular radio sounding of the atmosphere showed a characteristic behavior with small differences of the values between the air temperature and dew-point temperature profiles at aerosol smoke layer altitude. So the resulting stratification revealed the existence of atmospheric layers with aerosol trapping properties.

Effects of fatty infiltration in human livers on the backscattered statistics of ultrasound imaging.

PubMed

Wan, Yung-Liang; Tai, Dar-In; Ma, Hsiang-Yang; Chiang, Bing-Hao; Chen, Chin-Kuo; Tsui, Po-Hsiang

2015-06-01

Ultrasound imaging has been widely applied to screen fatty liver disease. Fatty liver disease is a condition where large vacuoles of triglyceride fat accumulate in liver cells, thereby altering the arrangement of scatterers and the corresponding backscattered statistics. In this study, we used ultrasound Nakagami imaging to explore the effects of fatty infiltration in human livers on the statistical distribution of backscattered signals. A total of 107 patients volunteered to participate in the experiments. The livers were scanned using a clinical ultrasound scanner to obtain the raw backscattered signals for ultrasound B-mode and Nakagami imaging. Clinical scores of fatty liver disease for each patient were determined according to a well-accepted sonographic scoring system. The results showed that the Nakagami image can visualize the local backscattering properties of liver tissues. The Nakagami parameter increased from 0.62 ± 0.11 to 1.02 ± 0.07 as the fatty liver disease stage increased from normal to severe, indicating that the backscattered statistics vary from pre-Rayleigh to Rayleigh distributions. A significant positive correlation (correlation coefficient ρ = 0.84; probability value (p value) < 0.0001) exists between the degree of fatty infiltration and the Nakagami parameter, suggesting that ultrasound Nakagami imaging has potentials in future applications in fatty liver disease diagnosis. © IMechE 2015.

[Balanced scorecard in health].

PubMed

Leyton-Pavez, Carolina Elena; Huerta-Riveros, Patricia Carolina; Paúl-Espinoza, Iván Renato

2015-01-01

To evaluate the installation of strategies in the higher complexity hospitals (HMC, in Spanish) of public health in Chile starting from the results of the Balanced Scorecard (BSC), during the years 2011-2012. The implementation of the BSC is described, the strategies and indicators identified, and the results of the 57 HMC compared and analyzed. Starting from the comparison of the results it is discovered that the BSC allows to evaluate the installation of the strategies. Differences are identified in the installation of the strategies by geographical area, with North presenting a higher score (20.21), followed by Center (10.41) and South (19.50), which can be explained by the size and complexity of this establishments, variables that should be incorporated in the evaluation of the results of the BSC.

[Definition of the specificity of DNA-methyltransferase M.Bsc4I in cell lysate by blocking of restriction endonucleases and computer modeling].

PubMed

Dedkov, V S

2009-01-01

The specificity of DNA-methyltransferase M.Bsc4I was defined in cellular lysate of Bacillus schlegelii 4. For this purpose, we used methylation sensitivity of restriction endonucleases, and also modeling of methylation. The modeling consisted in editing sequences of DNA using replacements of methylated bases and their complementary bases. The substratum DNA processed by M.Bsc4I also were used for studying sensitivity of some restriction endonucleases to methylation. Thus, it was shown that M.Bsc4I methylated 5'-Cm4CNNNNNNNGG-3' and the overlapped dcm-methylation blocked its activity. The offered approach can appear universal enough and simple for definition of specificity of DNA-methyltransferases.

Microwave dielectric properties of boreal forest trees

NASA Technical Reports Server (NTRS)

Xu, G.; Ahern, F.; Brown, J.

1993-01-01

The knowledge of vegetation dielectric behavior is important in studying the scattering properties of the vegetation canopy and radar backscatter modelling. Until now, a limited number of studies have been published on the dielectric properties in the boreal forest context. This paper presents the results of the dielectric constant as a function of depth in the trunks of two common boreal forest species: black spruce and trembling aspen, obtained from field measurements. The microwave penetration depth for the two species is estimated at C, L, and P bands and used to derive the equivalent dielectric constant for the trunk as a whole. The backscatter modelling is carried out in the case of black spruce and the results are compared with the JPL AIRSAR data. The sensitivity of the backscatter coefficient to the dielectric constant is also examined.

Soil moisture retrieval by active/passive microwave remote sensing data

NASA Astrophysics Data System (ADS)

Wu, Shengli; Yang, Lijuan

2012-09-01

This study develops a new algorithm for estimating bare surface soil moisture using combined active / passive microwave remote sensing on the basis of TRMM (Tropical Rainfall Measuring Mission). Tropical Rainfall Measurement Mission was jointly launched by NASA and NASDA in 1997, whose main task was to observe the precipitation of the area in 40 ° N-40 ° S. It was equipped with active microwave radar sensors (PR) and passive sensor microwave imager (TMI). To accurately estimate bare surface soil moisture, precipitation radar (PR) and microwave imager (TMI) are simultaneously used for observation. According to the frequency and incident angle setting of PR and TMI, we first need to establish a database which includes a large range of surface conditions; and then we use Advanced Integral Equation Model (AIEM) to calculate the backscattering coefficient and emissivity. Meanwhile, under the accuracy of resolution, we use a simplified theoretical model (GO model) and the semi-empirical physical model (Qp Model) to redescribe the process of scattering and radiation. There are quite a lot of parameters effecting backscattering coefficient and emissivity, including soil moisture, surface root mean square height, correlation length, and the correlation function etc. Radar backscattering is strongly affected by the surface roughness, which includes the surface root mean square roughness height, surface correlation length and the correlation function we use. And emissivity is differently affected by the root mean square slope under different polarizations. In general, emissivity decreases with the root mean square slope increases in V polarization, and increases with the root mean square slope increases in H polarization. For the GO model, we found that the backscattering coefficient is only related to the root mean square slope and soil moisture when the incident angle is fixed. And for Qp Model, through the analysis, we found that there is a quite good relationship between Qpparameter and root mean square slope. So here, root mean square slope is a parameter that both models shared. Because of its big influence to backscattering and emissivity, we need to throw it out during the process of the combination of GO model and Qp model. The result we obtain from the combined model is the Fresnel reflection coefficient in the normal direction gama(0). It has a good relationship with the soil dielectric constant. In Dobson Model, there is a detailed description about Fresnel reflection coefficient and soil moisture. With the help of Dobson model and gama(0) that we have obtained, we can get the soil moisture that we want. The backscattering coefficient and emissivity data used in combined model is from TRMM/PR, TMI; with this data, we can obtain gama(0); further, we get the soil moisture by the relationship of the two parameters-- gama(0) and soil moisture. To validate the accuracy of the retrieval soil moisture, there is an experiment conducted in Tibet. The soil moisture data which is used to validate the retrieval algorithm is from GAME-Tibet IOP98 Soil Moisture and Temperature Measuring System (SMTMS). There are 9 observing sites in SMTMS to validate soil moisture. Meanwhile, we use the SMTMS soil moisture data obtained by Time Domain Reflectometer (TDR) to do the validation. And the result shows the comparison of retrieval and measured results is very good. Through the analysis, we can see that the retrieval and measured results in D66 is nearly close; and in MS3608, the measured result is a little higher than retrieval result; in MS3637, the retrieval result is a little higher than measured result. According to the analysis of the simulation results, we found that this combined active and passive approach to retrieve the soil moisture improves the retrieval accuracy.

The SASS scattering coefficient algorithm. [Seasat-A Satellite Scatterometer

NASA Technical Reports Server (NTRS)

Bracalente, E. M.; Grantham, W. L.; Boggs, D. H.; Sweet, J. L.

1980-01-01

This paper describes the algorithms used to convert engineering unit data obtained from the Seasat-A satellite scatterometer (SASS) to radar scattering coefficients and associated supporting parameters. A description is given of the instrument receiver and related processing used by the scatterometer to measure signal power backscattered from the earth's surface. The applicable radar equation used for determining scattering coefficient is derived. Sample results of SASS data processed through current algorithm development facility (ADF) scattering coefficient algorithms are presented which include scattering coefficient values for both water and land surfaces. Scattering coefficient signatures for these two surface types are seen to have distinctly different characteristics. Scattering coefficient measurements of the Amazon rain forest indicate the usefulness of this type of data as a stable calibration reference target.

Time-frequency analysis of backscattered signals from diffuse radar targets

NASA Astrophysics Data System (ADS)

Kenny, O. P.; Boashash, B.

1993-06-01

The need for analysis of time-varying signals has led to the formulation of a class of joint time-frequency distributions (TFDs). One of these TFDs, the Wigner-Ville distribution (WVD), has useful properties which can be applied to radar imaging. The authors discuss time-frequency representation of the backscattered signal from a diffuse radar target. It is then shown that for point scatterers which are statistically dependent or for which the reflectivity coefficient has a nonzero mean value, reconstruction using time of flight positron emission tomography on time-frequency images is effective for estimating the scattering function of the target.

Inclusive blue swimming crab fishery management initiative in Betahwalang Demak, Indonesia

NASA Astrophysics Data System (ADS)

Ghofar, A.; Redjeki, S.; Madduppa, H.; Abbey, M.; Tasunar, N.

2018-02-01

There has been a growing interest in the sustainability of the blue swimming crab (Portunus pelagicus, BSC) fisheries in Indonesia. The fishery is operated on a small-scale basis and yet it significantly contributes to the Indonesia’s fisheries as the third biggest export commodities following tuna and shrimp. The project inclusively (i) brings together coastal and fishing communities, university, the private sector, government at various levels and international agencies, (ii) bottom up approach is integrated with top-down (government policy) approach and (iii) integration o f conservation into fisheries management. This approach resulted in better understanding and participation among the coastal fishing communities on sustainable fisheries and the necessity to perform fisheries management. This led to the establishment of BSC fishery management body (legally support by Village Regulation - No.06/2013 on BSC fishery management in 2013, followed by a District Regulation No.523/0166/2014 on BSC fishery management in 2014. More recently, the Governor of Central Java issued a Governor Regulation No. 33/2017 on Crab and Lobster fisheries management and a Governor Decree No. 523/93/2017 on the establishment of the BSC fisheries management committee in Central Java. Further impacts have been raised awareness in sustainable BSC fishery management in surrounding districts in other provinces, namely East Java and Southeast Sulawesi. There remains, further needs to strengthen fishery governance by means of integrating national and local government effort in sustaining the fisheries, including the Issuance and effective implementation of the provincial decree on BSC fishery management for Central Java, that will enable the use of province’s resource to implement fisheries management and strengthen law enforcement. To help improve the stock, a plan for stock enhancement should also be developed with proper monitoring program and community commitment to avoid “put and take” practices.

Diel hysteresis between soil respiration and soil temperature in a biological soil crust covered desert ecosystem

PubMed Central

Li, Xinrong; Zhang, Peng; Chen, Yongle

2018-01-01

Soil respiration induced by biological soil crusts (BSCs) is an important process in the carbon (C) cycle in arid and semi-arid ecosystems, where vascular plants are restricted by the harsh environment, particularly the limited soil moisture. However, the interaction between temperature and soil respiration remains uncertain because of the number of factors that control soil respiration, including temperature and soil moisture, especially in BSC-dominated areas. In this study, the soil respiration in moss-dominated crusts and lichen-dominated crusts was continuously measured using an automated soil respiration system over a one-year period from November 2015 to October 2016 in the Shapotou region of the Tengger Desert, northern China. The results indicated that over daily cycles, the half-hourly soil respiration rates in both types of BSC-covered areas were commonly related to the soil temperature. The observed diel hysteresis between the half-hourly soil respiration rates and soil temperature in the BSC-covered areas was limited by nonlinearity loops with semielliptical shapes, and soil temperature often peaked later than the half-hourly soil respiration rates in the BSC-covered areas. The average lag times between the half-hourly soil respiration rates and soil temperature for both types of BSC-covered areas were two hours over the diel cycles, and they were negatively and linearly related to the volumetric soil water content. Our results highlight the diel hysteresis phenomenon that occurs between soil respiration rates and soil temperatures in BSC-covered areas and the negative response of this phenomenon to soil moisture, which may influence total C budget evaluations. Therefore, the interactive effects of soil temperature and moisture on soil respiration in BSC-covered areas should be considered in global carbon cycle models of desert ecosystems. PMID:29624606

Microbial Community and Biochemical Dynamics of Biological Soil Crusts across a Gradient of Surface Coverage in the Central Mojave Desert.

PubMed

Mogul, Rakesh; Vaishampayan, Parag; Bashir, Mina; McKay, Chris P; Schubert, Keith; Bornaccorsi, Rosalba; Gomez, Ernesto; Tharayil, Sneha; Payton, Geoffrey; Capra, Juliana; Andaya, Jessica; Bacon, Leonard; Bargoma, Emily; Black, David; Boos, Katie; Brant, Michaela; Chabot, Michael; Chau, Danny; Cisneros, Jessica; Chu, Geoff; Curnutt, Jane; DiMizio, Jessica; Engelbrecht, Christian; Gott, Caroline; Harnoto, Raechel; Hovanesian, Ruben; Johnson, Shane; Lavergne, Britne; Martinez, Gabriel; Mans, Paul; Morales, Ernesto; Oei, Alex; Peplow, Gary; Piaget, Ryan; Ponce, Nicole; Renteria, Eduardo; Rodriguez, Veronica; Rodriguez, Joseph; Santander, Monica; Sarmiento, Khamille; Scheppelmann, Allison; Schroter, Gavin; Sexton, Devan; Stephenson, Jenin; Symer, Kristin; Russo-Tait, Tatiane; Weigel, Bill; Wilhelm, Mary B

2017-01-01

In this study, we expand upon the biogeography of biological soil crusts (BSCs) and provide molecular insights into the microbial community and biochemical dynamics along the vertical BSC column structure, and across a transect of increasing BSC surface coverage in the central Mojave Desert, CA, United States. Next generation sequencing reveals a bacterial community profile that is distinct among BSCs in the southwestern United States. Distribution of major phyla in the BSC topsoils included Cyanobacteria (33 ± 8%), Proteobacteria (26 ± 6%), and Chloroflexi (12 ± 4%), with Phormidium being the numerically dominant genus. Furthermore, BSC subsurfaces contained Proteobacteria (23 ± 5%), Actinobacteria (20 ± 5%), and Chloroflexi (18 ± 3%), with an unidentified genus from Chloroflexi (AKIW781, order) being numerically dominant. Across the transect, changes in distribution at the phylum ( p < 0.0439) and genus ( p < 0.006) levels, including multiple biochemical and geochemical trends ( p < 0.05), positively correlated with increasing BSC surface coverage. This included increases in (a) Chloroflexi abundance, (b) abundance and diversity of Cyanobacteria, (b) OTU-level diversity in the topsoil, (c) OTU-level differentiation between the topsoil and subsurface, (d) intracellular ATP abundances and catalase activities, and (e) enrichments in clay, silt, and varying elements, including S, Mn, Co, As, and Pb, in the BSC topsoils. In sum, these studies suggest that BSCs from regions of differing surface coverage represent early successional stages, which exhibit increasing bacterial diversity, metabolic activities, and capacity to restructure the soil. Further, these trends suggest that BSC successional maturation and colonization across the transect are inhibited by metals/metalloids such as B, Ca, Ti, Mn, Co, Ni, Mo, and Pb.

Microbial Community and Biochemical Dynamics of Biological Soil Crusts across a Gradient of Surface Coverage in the Central Mojave Desert

PubMed Central

Mogul, Rakesh; Vaishampayan, Parag; Bashir, Mina; McKay, Chris P.; Schubert, Keith; Bornaccorsi, Rosalba; Gomez, Ernesto; Tharayil, Sneha; Payton, Geoffrey; Capra, Juliana; Andaya, Jessica; Bacon, Leonard; Bargoma, Emily; Black, David; Boos, Katie; Brant, Michaela; Chabot, Michael; Chau, Danny; Cisneros, Jessica; Chu, Geoff; Curnutt, Jane; DiMizio, Jessica; Engelbrecht, Christian; Gott, Caroline; Harnoto, Raechel; Hovanesian, Ruben; Johnson, Shane; Lavergne, Britne; Martinez, Gabriel; Mans, Paul; Morales, Ernesto; Oei, Alex; Peplow, Gary; Piaget, Ryan; Ponce, Nicole; Renteria, Eduardo; Rodriguez, Veronica; Rodriguez, Joseph; Santander, Monica; Sarmiento, Khamille; Scheppelmann, Allison; Schroter, Gavin; Sexton, Devan; Stephenson, Jenin; Symer, Kristin; Russo-Tait, Tatiane; Weigel, Bill; Wilhelm, Mary B.

2017-01-01

In this study, we expand upon the biogeography of biological soil crusts (BSCs) and provide molecular insights into the microbial community and biochemical dynamics along the vertical BSC column structure, and across a transect of increasing BSC surface coverage in the central Mojave Desert, CA, United States. Next generation sequencing reveals a bacterial community profile that is distinct among BSCs in the southwestern United States. Distribution of major phyla in the BSC topsoils included Cyanobacteria (33 ± 8%), Proteobacteria (26 ± 6%), and Chloroflexi (12 ± 4%), with Phormidium being the numerically dominant genus. Furthermore, BSC subsurfaces contained Proteobacteria (23 ± 5%), Actinobacteria (20 ± 5%), and Chloroflexi (18 ± 3%), with an unidentified genus from Chloroflexi (AKIW781, order) being numerically dominant. Across the transect, changes in distribution at the phylum (p < 0.0439) and genus (p < 0.006) levels, including multiple biochemical and geochemical trends (p < 0.05), positively correlated with increasing BSC surface coverage. This included increases in (a) Chloroflexi abundance, (b) abundance and diversity of Cyanobacteria, (b) OTU-level diversity in the topsoil, (c) OTU-level differentiation between the topsoil and subsurface, (d) intracellular ATP abundances and catalase activities, and (e) enrichments in clay, silt, and varying elements, including S, Mn, Co, As, and Pb, in the BSC topsoils. In sum, these studies suggest that BSCs from regions of differing surface coverage represent early successional stages, which exhibit increasing bacterial diversity, metabolic activities, and capacity to restructure the soil. Further, these trends suggest that BSC successional maturation and colonization across the transect are inhibited by metals/metalloids such as B, Ca, Ti, Mn, Co, Ni, Mo, and Pb. PMID:29109701

Evaluating the Fraser Health Balanced Scorecard--a formative evaluation.

PubMed

Barnardo, Catherine; Jivanni, Amin

2009-01-01

Fraser Health (FH), a large, Canadian, integrated health care network, adopted the Balanced Scorecard (BSC) approach to monitor organizational performance in 2006. This paper reports on the results of a formative evaluation, conducted in April, 2008, to assess the usefulness of the BSC as a performance-reporting system and a performance management tool. Results indicated that the BSC has proven to be useful for reporting performance but is not currently used for performance management in a substantial way.

Isolation and characterization of Klebsiella oxytoca strain degrading crude oil from a Tunisian off-shore oil field.

PubMed

Chamkha, Mohamed; Trabelsi, Yosra; Mnif, Sami; Sayadi, Sami

2011-12-01

A facultatively anaerobic, Gram-negative, mesophilic, moderately halotolerant, non-motile, and non-sporulated bacterium, designated strain BSC5 was isolated from an off-shore "Sercina" oil field, located near the Kerkennah island, Tunisia. Yeast extract was not required for growth. Phenotypic characteristics and phylogenetic analysis of the 16S rRNA gene sequence of strain BSC5 revealed that it was related to members of the genus Klebsiella, being most closely related to the type strain of K. oxytoca (99% sequence similarity). Strain BSC5 was capable of using aerobically the crude oil as substrate growth. The growth of strain BSC5 on crude oil was followed by measuring the OD(600 nm) and by enumeration of viable cells at different culture's time. GC-MS analysis showed that strain BSC5 was capable of degrading a wide range of aliphatic hydrocarbons from C(13) to C(30) . The biodegradation rate for n -alkanes reached 44% and 75%, after 20 and 45 days of incubation, respectively. Addition of the synthetic surfactant, Tween 80, accelerated the crude oil degradation. The biodegradation rate for n -alkanes reached 61% and 98%, after 20 and 45 days of incubation, respectively. Moreover, three aromatic compounds, p -hydroxybenzoate, protocatechuate and gentisate, were metabolized completely by strain BSC5 after 24 h, under aerobic conditions. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Signal Processing and Calibration of Continuous-Wave Focused CO2 Doppler Lidars for Atmospheric Backscatter Measurement

NASA Technical Reports Server (NTRS)

Rothermel, Jeffry; Chambers, Diana M.; Jarzembski, Maurice A.; Srivastava, Vandana; Bowdle, David A.; Jones, William D.

1996-01-01

Two continuous-wave(CW)focused C02 Doppler lidars (9.1 and 10.6 micrometers) were developed for airborne in situ aerosol backscatter measurements. The complex path of reliably calibrating these systems, with different signal processors, for accurate derivation of atmospheric backscatter coefficients is documented. Lidar calibration for absolute backscatter measurement for both lidars is based on range response over the lidar sample volume, not solely at focus. Both lidars were calibrated with a new technique using well-characterized aerosols as radiometric standard targets and related to conventional hard-target calibration. A digital signal processor (DSP), a surface acoustic and spectrum analyzer and manually tuned spectrum analyzer signal analyzers were used. The DSP signals were analyzed with an innovative method of correcting for systematic noise fluctuation; the noise statistics exhibit the chi-square distribution predicted by theory. System parametric studies and detailed calibration improved the accuracy of conversion from the measured signal-to-noise ratio to absolute backscatter. The minimum backscatter sensitivity is approximately 3 x 10(exp -12)/m/sr at 9.1 micrometers and approximately 9 x 10(exp -12)/m/sr at 10.6 micrometers. Sample measurements are shown for a flight over the remote Pacific Ocean in 1990 as part of the NASA Global Backscatter Experiment (GLOBE) survey missions, the first time to our knowledge that 9.1-10.6 micrometer lidar intercomparisons were made. Measurements at 9.1 micrometers, a potential wavelength for space-based lidar remote-sensing applications, are to our knowledge the first based on the rare isotope C-12 O(2)-18 gas.

The use and design of the BSC in the health care sector: A systematic literature review for Italy, Spain, and Portugal.

PubMed

Gonzalez-Sanchez, Maria Beatriz; Broccardo, Laura; Martins Pires, Amélia Maria

2018-01-01

The aim of this paper is to gain a better understanding of how the balanced scorecard (BSC) has evolved in Spain, Italy, and Portugal. It reviews all the articles on the BSC in the health care sector written between 1992 and 2015 by Spanish, Italian, or Portuguese authors and published in Spanish, Italian, or Portuguese as well as in English. Our study first shows the state of knowledge on BSC in health care for a homogeneous group of Southern European countries. Second, it uncovers the perspectives, indicators, and generation used in the countries under observation to reveal the extent to which this management tool has evolved. Third, it analyses international variations in design and use within the health care context, especially in the United States. Moreover, it also highlights a number of important issues. The BSC is in its early stage of development in these 3 countries, which do not use it as a tool to implement strategy and align all of the elements that help integrate the organization. Copyright © 2017 John Wiley & Sons, Ltd.

Small-scale Scheimpflug lidar for aerosol extinction coefficient and vertical atmospheric transmittance detection.

PubMed

Sun, Guodong; Qin, Laian; Hou, Zaihong; Jing, Xu; He, Feng; Tan, Fengfu; Zhang, Silong

2018-03-19

In this paper, a new prototypical Scheimpflug lidar capable of detecting the aerosol extinction coefficient and vertical atmospheric transmittance at 1 km above the ground is described. The lidar system operates at 532 nm and can be used to detect aerosol extinction coefficients throughout an entire day. Then, the vertical atmospheric transmittance can be determined from the extinction coefficients with the equation of numerical integration in this area. CCD flat fielding of the image data is used to mitigate the effects of pixel sensitivity variation. An efficient method of two-dimensional wavelet transform according to a local threshold value has been proposed to reduce the Gaussian white noise in the lidar signal. Furthermore, a new iteration method of backscattering ratio based on genetic algorithm is presented to calculate the aerosol extinction coefficient and vertical atmospheric transmittance. Some simulations are performed to reduce the different levels of noise in the simulated signal in order to test the precision of the de-noising method and inversion algorithm. The simulation result shows that the root-mean-square errors of extinction coefficients are all less than 0.02 km -1 , and that the relative errors of the atmospheric transmittance between the model and inversion data are below 0.56% for all cases. The feasibility of the instrument and the inversion algorithm have also been verified by an optical experiment. The average relative errors of aerosol extinction coefficients between the Scheimpflug lidar and the conventional backscattering elastic lidar are 3.54% and 2.79% in the full overlap heights of two time points, respectively. This work opens up new possibilities of using a small-scale Scheimpflug lidar system for the remote sensing of atmospheric aerosols.

Hydroacoustic estimation of zooplankton biomass at two shoal complexes in the Apostle Islands Region of Lake Superior

USGS Publications Warehouse

Holbrook, B.V.; Hrabik, T.R.; Branstrator, D.K.; Yule, D.L.; Stockwell, J.D.

2006-01-01

Hydroacoustics can be used to assess zooplankton populations, however, backscatter must be scaled to be biologically meaningful. In this study, we used a general model to correlate site-specific hydroacoustic backscatter with zooplankton dry weight biomass estimated from net tows. The relationship between zooplankton dry weight and backscatter was significant (p < 0.001) and explained 76% of the variability in the dry weight data. We applied this regression to hydroacoustic data collected monthly in 2003 and 2004 at two shoals in the Apostle Island Region of Lake Superior. After applying the regression model to convert hydroacoustic backscatter to zooplankton dry weight biomass, we used geostatistics to analyze the mean and variance, and ordinary kriging to create spatial zooplankton distribution maps. The mean zooplankton dry weight biomass estimates from plankton net tows and hydroacoustics were not significantly different (p = 0.19) but the hydroacoustic data had a significantly lower coefficient of variation (p < 0.001). The maps of zooplankton distribution illustrated spatial trends in zooplankton dry weight biomass that were not discernable from the overall means.

Snow Cover Mapping and Ice Avalanche Monitoring from the Satellite Data of the Sentinels

NASA Astrophysics Data System (ADS)

Wang, S.; Yang, B.; Zhou, Y.; Wang, F.; Zhang, R.; Zhao, Q.

2018-04-01

In order to monitor ice avalanches efficiently under disaster emergency conditions, a snow cover mapping method based on the satellite data of the Sentinels is proposed, in which the coherence and backscattering coefficient image of Synthetic Aperture Radar (SAR) data (Sentinel-1) is combined with the atmospheric correction result of multispectral data (Sentinel-2). The coherence image of the Sentinel-1 data could be segmented by a certain threshold to map snow cover, with the water bodies extracted from the backscattering coefficient image and removed from the coherence segment result. A snow confidence map from Sentinel-2 was used to map the snow cover, in which the confidence values of the snow cover were relatively high. The method can make full use of the acquired SAR image and multispectral image under emergency conditions, and the application potential of Sentinel data in the field of snow cover mapping is exploited. The monitoring frequency can be ensured because the areas obscured by thick clouds are remedied in the monitoring results. The Kappa coefficient of the monitoring results is 0.946, and the data processing time is less than 2 h, which meet the requirements of disaster emergency monitoring.

Bayesian assessment of uncertainty in aerosol size distributions and index of refraction retrieved from multiwavelength lidar measurements.

PubMed

Herman, Benjamin R; Gross, Barry; Moshary, Fred; Ahmed, Samir

2008-04-01

We investigate the assessment of uncertainty in the inference of aerosol size distributions from backscatter and extinction measurements that can be obtained from a modern elastic/Raman lidar system with a Nd:YAG laser transmitter. To calculate the uncertainty, an analytic formula for the correlated probability density function (PDF) describing the error for an optical coefficient ratio is derived based on a normally distributed fractional error in the optical coefficients. Assuming a monomodal lognormal particle size distribution of spherical, homogeneous particles with a known index of refraction, we compare the assessment of uncertainty using a more conventional forward Monte Carlo method with that obtained from a Bayesian posterior PDF assuming a uniform prior PDF and show that substantial differences between the two methods exist. In addition, we use the posterior PDF formalism, which was extended to include an unknown refractive index, to find credible sets for a variety of optical measurement scenarios. We find the uncertainty is greatly reduced with the addition of suitable extinction measurements in contrast to the inclusion of extra backscatter coefficients, which we show to have a minimal effect and strengthens similar observations based on numerical regularization methods.

Development and characterization of a tissue-mimicking material for high-intensity focused ultrasound.

PubMed

King, Randy L; Liu, Yunbo; Maruvada, Subha; Herman, Bruce A; Wear, Keith A; Harris, Gerald R

2011-07-01

A tissue-mimicking material (TMM) for the acoustic and thermal characterization of high-intensity focused ultrasound (HIFU) devices has been developed. The material is a high-temperature hydrogel matrix (gellan gum) combined with different sizes of aluminum oxide particles and other chemicals. The ultrasonic properties (attenuation coefficient, speed of sound, acoustical impedance, and the thermal conductivity and diffusivity) were characterized as a function of temperature from 20 to 70°C. The backscatter coefficient and nonlinearity parameter B/A were measured at room temperature. Importantly, the attenuation coefficient has essentially linear frequency dependence, as is the case for most mammalian tissues at 37°C. The mean value is 0.64f(0.95) dB·cm(-1) at 20°C, based on measurements from 2 to 8 MHz. Most of the other relevant physical parameters are also close to the reported values, although backscatter signals are low compared with typical human soft tissues. Repeatable and consistent temperature elevations of 40°C were produced under 20-s HIFU exposures in the TMM. This TMM is appropriate for developing standardized dosimetry techniques, validating numerical models, and determining the safety and efficacy of HIFU devices.

Using Airborne High Spectral Resolution Lidar Data to Evaluate Combined Active Plus Passive Retrievals of Aerosol Extinction Profiles

NASA Technical Reports Server (NTRS)

Burton, S. P.; Ferrare, R. A.; Hostetler, C. A.; Hair, J. W.; Kittaka, C.; Vaughn, M. A.; Remer, L. A.

2010-01-01

We derive aerosol extinction profiles from airborne and space-based lidar backscatter signals by constraining the retrieval with column aerosol optical thickness (AOT), with no need to rely on assumptions about aerosol type or lidar ratio. The backscatter data were acquired by the NASA Langley Research Center airborne High Spectral Resolution Lidar (HSRL) and by the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) instrument on the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) satellite. The HSRL also simultaneously measures aerosol extinction coefficients independently using the high spectral resolution lidar technique, thereby providing an ideal data set for evaluating the retrieval. We retrieve aerosol extinction profiles from both HSRL and CALIOP attenuated backscatter data constrained with HSRL, Moderate-Resolution Imaging Spectroradiometer (MODIS), and Multiangle Imaging Spectroradiometer column AOT. The resulting profiles are compared with the aerosol extinction measured by HSRL. Retrievals are limited to cases where the column aerosol thickness is greater than 0.2 over land and 0.15 over water. In the case of large AOT, the results using the Aqua MODIS constraint over water are poorer than Aqua MODIS over land or Terra MODIS. The poorer results relate to an apparent bias in Aqua MODIS AOT over water observed in August 2007. This apparent bias is still under investigation. Finally, aerosol extinction coefficients are derived from CALIPSO backscatter data using AOT from Aqua MODIS for 28 profiles over land and 9 over water. They agree with coincident measurements by the airborne HSRL to within +/-0.016/km +/- 20% for at least two-thirds of land points and within +/-0.028/km +/- 20% for at least two-thirds of ocean points.

Second Harmonic Generation Confocal Microscopy of Collagen Type I from Rat Tendon Cryosections

PubMed Central

Theodossiou, Theodossis A.; Thrasivoulou, Christopher; Ekwobi, Chidi; Becker, David L.

2006-01-01

We performed second harmonic generation (SHG) imaging of collagen in rat-tendon cryosections, using femtosecond laser scanning confocal microscopy, both in backscattering and transmission geometries. SHG transmission images of collagen fibers were spatially resolved due to a coherent, directional SHG component. This effect was enhanced with the use of an index-matching fluid (ni = 1.52). The average SHG intensity oscillated with wavelength in the backscattered geometry (isotropic SHG component), whereas the spectral profile was consistent with quasi-phase-matching conditions in transmission geometry (forward propagating, coherent SHG component) around 440 nm (λp = 880 nm). Collagen type I from bovine Achilles tendon was imaged for SHG in the backscattered geometry and its first-order effective nonlinear coefficient was determined (\\documentclass[10pt]{article} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\pagestyle{empty} \\oddsidemargin -1.0in \\begin{document} \\begin{equation*}{\\vert}d_{{\\mathrm{eff}}}{\\vert}\\approx 0.085({\\pm}0.025){\\times}10^{-12}{\\mathrm{mV}}^{-1}\\end{equation*}\\end{document}) by comparison to samples of inorganic materials with known effective nonlinear coefficients (LiNbO3 and LiIO3). The SHG spectral response of collagen type I from bovine Achilles tendon matched that of the rat-tendon cryosections in backscattered geometry. Collagen types I, II, and VI powders (nonfibrous) did not show any detectable SHG, indicating a lack of noncentrosymmetric crystalline structure at the molecular level. The various stages of collagen thermal denaturation were investigated in rat-tendon cryosections using SHG and bright-field imaging. Thermal denaturation resulted in the gradual destruction of the SHG signal. PMID:17130233

Modeling and measurement of microwave emission and backscattering from bare soil surfaces

NASA Technical Reports Server (NTRS)

Saatchi, S.; Wegmuller, U.

1992-01-01

A multifrequency ground-based radiometer-scatterometer system working at frequencies between 3.0 GHz and 11.0 GHz has been used to study the effect of soil moisture and roughness on microwave emission and backscattering. The freezing and thawing effect of the soil surface and the changes of the surface roughness due to rain and erosion are reported. To analyze the combined active and passive data, a scattering model based on physical optics approximation for the low frequency and geometrical optics approximation for high frequency has been developed. The model is used to calculate the bistatic scattering coefficients from the surface. By considering the conservation of energy, the result has been integrated over a hemisphere above the surface to calculate the emissivity. The backscattering and emission model has been coupled with the observed data in order to extract soil moisture and surface roughness.

COSMO-SkyMed potentiality to identify crop-specific behavior and monitor phenological parameters

NASA Astrophysics Data System (ADS)

Guarini, Rocchina; Segalini, Federica; Mastronardi, Giovanni; Notarnicola, Claudia; Vuolo, Francesco; Dini, Luigi

2014-10-01

This work aims at investigating the capability of COSMO-SkyMed® (CSK®) constellation of Synthetic Aperture Radar (SAR) system to monitor the Leaf Area Index (LAI) of different crops. The experiment was conducted in the Marchfeld Region, an agricultural Austrian area, and focused on five crop species: sugar beet, soybean, potato, pea and corn. A linear regression analysis was carried out to assess the sensitivity of CSK® backscattering coefficients to crops changes base on LAI values. CSK® backscattering coefficients were averaged at a field scale (<σ°dB>) and were compared to the DEIMOS-1 derived values of estimated LAI. LAI were as well averaged over the corresponding fields (). CSK® data acquired at three polarizations (HH, VV and VH), four incidence angles (23°, 33°, 40° and 57°) and at different pixel spacings (2.5 m and 10 m) were tested to assess whether spatial resolution may influence results at a field scale and to find the best combination of polarizations and CSK® acquisition beams which indicate the highest sensitivity to crop LAI values. The preliminary results show that sugar beet can be well monitored (r = 0.72 - 0.80) by CSK® by using any of the polarization acquisition modes, at moderate to shallow incidence angles (33° - 57°). Slightly weaker correlations were found, at VH polarization only, between CSK® < σ°dB> and for potato (r = 0.65), pea (r = 0.65) and soybean (r = -0.83). Shallower view incidence angles seem to be preferable to steep ones in most cases. CSK® backscattering coefficients were no sensitive at all to LAI changes for already developed corn fields.

Estimation of PM2.5 and PM10 using ground-based AOD measurements during KORUS-AQ campaign

NASA Astrophysics Data System (ADS)

Koo, J. H.; Kim, J.; Kim, S.; Go, S.; Lee, S.; Lee, H.; Mok, J.; Hong, J.; Lee, J.; Eck, T. F.; Holben, B. N.

2017-12-01

During the KORUS-AQ campaign (2 May - 12 June, 2016), aerosol optical depth (AOD) was obtained at multiple channels using various ground-based instruments at Yonsei University, Seoul: AERONET sunphotometer, SKYNET skyradiometer, Brewer spectrophotometer, and multi-filter rotating shadowband radiometer (MFRSR). At the same location, planetary boundary layer (PBL) height and vertical profile of backscattering coefficients also can be obtained based on the celiometer measurements. Using celiometer products and various AODs, we try to estimate the amount of particular matter (PM2.5 and PM10) and validate with in-situ surface PM2.5 and PM10 measurements from AIRKOREA network. Direct comparison between PM2.5 and AOD reveals that the ultraviolet(UV) channel AOD has better correlations, due to the higher sensitivity of short wavelength to the fine-mode particle. In contrast, PM10 shows the highest correlation with the near-infrared(NIR) AOD. Next, we extract the boundary-layer portion of AOD using either PBL height or vertical profile of backscattering coefficients to compare with PM2.5 and PM10. Both results enhance the correlation, but consideration of weighting factor calculated from backscattering coefficients shows larger contribution to the correlation increase. Finally, we performed the multiple linear regression to estimate PM2.5 and PM10 using AODs. Consideration of meteorology (temperature, wind speed, and relative humidity) can enhance the correlation and also O3 and NO2 consideration highly contributes to the high correlation. This finding implies the importance to consider the ambient condition of secondary aerosol formation related to the PM2.5 variation. Multiple regression model finally finds the correlation 0.7-0.8, and diminishes the wavelength-dependent correlation patterns.

Sensitivity of the Lidar ratio to changes in size distribution and index of refraction

NASA Technical Reports Server (NTRS)

Evans, B. T. N.

1986-01-01

In order to invert lidar signals to obtain reliable extinction coefficients, sigma, a relationship between sigma and the backscatter coefficient, beta, must be given. These two coefficients are linearly related if the complex index of refraction, m, particle shape size distribution, N, does not change along the path illuminated by the laser beam. This, however, is generally not the case. An extensive Mie computation of the lidar ratio R = beta/sigma and the sensitivity of R to the changes in a parametric space defined by N and m were examined.

A study of a nursing department performance measurement system: using the Balanced Scorecard and the Analytic Hierarchy Process.

PubMed

Chu, Hsuan-Lien; Wang, Chen-Chin; Dai, Yu-Tzu

2009-01-01

The health care industry is under pressure from government and private entities as well as from market conditions to contain costs. In an effort to respond to these pressures, the case hospital in this study implemented a Balanced Scorecard (BSC) in January 2003 and integrated it with the hospital's formal incentive plan for non-physicians in January 2005. The nursing department's performance improved in the 2 years following the introduction of the plan. This study contributes to the literature by demonstrating the performance improvement that results from integrating the BSC with an incentive plan in the nursing field. The results provide insight into the current BSC performance metrics applied by the case nursing department, and could be used as guidelines by other health care organizations that wish to implement BSC-based incentive plans.

Modifying the Balanced Scorecard for a Network Industry The Case of the Clearing Industry

NASA Astrophysics Data System (ADS)

Chlistalla, Michael; Schaper, Torsten

The Balanced Scorecard (BSC) is a well-established framework for the management of a company as it integrates financial and non-financial perspectives. Little attention has been given to its theoretical and conceptual valuation. We illustrate how the stakeholder value theory corresponds with the concept of the BSC and show the importance of underlying cause-and-effect relationships between its perspectives. For the case of clearing in Europe which is currently facing profound changes, we present our three-phased approach how to adjust and to extend Kaplan and Norton’s original concept. We modify the generic BSC by adding risk management as a separate perspective and by integrating competition and IT. Based on multiple case studies, we then validate whether the modified BSC is suited to meet the specifics of the clearing industry.

A balanced scorecard for health services in Afghanistan.

PubMed

Peters, David H; Noor, Ayan Ahmed; Singh, Lakhwinder P; Kakar, Faizullah K; Hansen, Peter M; Burnham, Gilbert

2007-02-01

The Ministry of Public Health (MOPH) in Afghanistan has developed a balanced scorecard (BSC) to regularly monitor the progress of its strategy to deliver a basic package of health services. Although frequently used in other health-care settings, this represents the first time that the BSC has been employed in a developing country. The BSC was designed via a collaborative process focusing on translating the vision and mission of the MOPH into 29 core indicators and benchmarks representing six different domains of health services, together with two composite measures of performance. In the absence of a routine health information system, the 2004 BSC for Afghanistan was derived from a stratified random sample of 617 health facilities, 5719 observations of patient-provider interactions, and interviews with 5597 patients, 1553 health workers, and 13,843 households. Nationally, health services were found to be reaching more of the poor than the less-poor population, and providing for more women than men, both key concerns of the government. However, serious deficiencies were found in five domains, and particularly in counselling patients, providing delivery care during childbirth, monitoring tuberculosis treatment, placing staff and equipment, and establishing functional village health councils. The BSC also identified wide variations in performance across provinces; no province performed better than the others across all domains. The innovative adaptation of the BSC in Afghanistan has provided a useful tool to summarize the multidimensional nature of health-services performance, and is enabling managers to benchmark performance and identify strengths and weaknesses in the Afghan context.

Estimating wheat growth with radar vegetation indices

USDA-ARS?s Scientific Manuscript database

In this study, we computed the Radar Vegetation Index (RVI) using observations made with a ground based multi-frequency polarimetric scatterometer system over an entire wheat growth period. The temporal variations of the backscattering coefficients for L-, C-, and X-band, RVI, vegetation water conte...

Simultaneous aerosol/ocean products retrieved during the 2014 SABOR campaign using the NASA Research Scanning Polarimeter (RSP)

NASA Astrophysics Data System (ADS)

Stamnes, S.; Hostetler, C. A.; Ferrare, R. A.; Hair, J. W.; Burton, S. P.; Liu, X.; Hu, Y.; Stamnes, K. H.; Chowdhary, J.; Brian, C.

2017-12-01

The SABOR (Ship-Aircraft Bio-Optical Research) campaign was conducted during the summer of 2014, in the Atlantic Ocean, over the Chesapeake Bay and the eastern coastal region of the United States. The NASA GISS Research Scanning Polarimeter, a multi-angle, multi-spectral polarimeter measured the upwelling polarized radiances from a B200 aircraft. We present results from the new "MAPP" algorithm for RSP that is based on optimal estimation and that can retrieve simultaneous aerosol microphysical properties (including effective radius, single-scattering albedo, and real refractive index) and ocean color products using accurate radiative transfer and Mie calculations. The algorithm was applied to data collected during SABOR to retrieve aerosol microphysics and ocean products for all Aerosols-Above-Ocean (AAO) scenes. The RSP MAPP products are compared against collocated aerosol extinction and backscatter profiles collected by the NASA LaRC airborne High Spectral Resolution Lidar (HSRL-1), including lidar depth profiles of the ocean diffuse attenuation coefficient and the hemispherical backscatter coefficient.

Characterization of cesium diffusion behavior into granite matrix using Rutherford backscattering spectrometry

NASA Astrophysics Data System (ADS)

Tsai, Shih-Chin; Lee, Chuan-Pin; Tsai, Tsuey-Lin; Yu, Yueh-Chung

2017-10-01

The characterization of radionuclide diffusion behavior is necessary for performance assessment of granite as a geological barrier for high-level radioactive waste disposal. Rutherford backscattering spectrometry (RBS), a novel nuclear ion-beam technique, was selected in this study because it is suitable for analyzing the concentration gradients of heavy elements in a well-defined matrix and allows measuring diffusion coefficients on a micrometer scale. In this study Cs was selected to represent Cs-135 (a key radionuclide in high-level waste) diffusion in granite. The Cs energy spectrum and concentration deep profile were analyzed and the diffusion coefficient of Cs in granite for three different locations were determined, which were 2.06 × 10-19m2 s-1, 3.58 × 10-19m2 s-1, and 7.19 × 10-19m2 s-1-19m2 s-19m2 s-1, respectively, which were of a similiar order of magnitude. Results from other studies are also compared and discussed in this paper.

Typical tropospheric aerosol backscatter profiles for Southern Ireland: The Cork Raman lidar

NASA Astrophysics Data System (ADS)

McAuliffe, Michael A. P.; Ruth, Albert A.

2013-02-01

A Raman lidar instrument (UCLID) was established at the University College Cork as part of the European lidar network EARLINET. Raman backscatter coefficients, extinction coefficients and lidar ratios were measured within the period 28/08/2010 and 24/04/2011. Typical atmospheric scenarios over Southern Ireland in terms of the aerosol load in the planetary boundary layer are outlined. The lidar ratios found are typical for marine atmospheric condition (lidar ratio ca. 20-25 sr). The height of the planetary boundary layer is below 1000 m and therefore low in comparison to heights found at other lidar sites in Europe. On the 21st of April a large aerosol load was detected, which was assigned to a Saharan dust event based on HYSPLIT trajectories and DREAM forecasts along with the lidar ratio (70 sr) for the period concerned. The dust was found at two heights, pure dust at 2.5 km and dust mixing with pollution from 0.7 to 1.8 km with a lidar ratio of 40-50 sr.

Near-real-time processing of a ceilometer network assisted with sun-photometer data: monitoring a dust outbreak over the Iberian Peninsula

NASA Astrophysics Data System (ADS)

Cazorla, Alberto; Andrés Casquero-Vera, Juan; Román, Roberto; Guerrero-Rascado, Juan Luis; Toledano, Carlos; Cachorro, Victoria E.; Orza, José Antonio G.; Cancillo, María Luisa; Serrano, Antonio; Titos, Gloria; Pandolfi, Marco; Alastuey, Andres; Hanrieder, Natalie; Alados-Arboledas, Lucas

2017-10-01

The interest in the use of ceilometers for optical aerosol characterization has increased in the last few years. They operate continuously almost unattended and are also much less expensive than lidars; hence, they can be distributed in dense networks over large areas. However, due to the low signal-to-noise ratio it is not always possible to obtain particle backscatter coefficient profiles, and the vast number of data generated require an automated and unsupervised method that ensures the quality of the profiles inversions. In this work we describe a method that uses aerosol optical depth (AOD) measurements from the AERONET network that it is applied for the calibration and automated quality assurance of inversion of ceilometer profiles. The method is compared with independent inversions obtained by co-located multiwavelength lidar measurements. A difference smaller than 15 % in backscatter is found between both instruments. This method is continuously and automatically applied to the Iberian Ceilometer Network (ICENET) and a case example during an unusually intense dust outbreak affecting the Iberian Peninsula between 20 and 24 February 2016 is shown. Results reveal that it is possible to obtain quantitative optical aerosol properties (particle backscatter coefficient) and discriminate the quality of these retrievals with ceilometers over large areas. This information has a great potential for alert systems and model assimilation and evaluation.

Monitoring of land degradation from overgrazing using space-borne radar and optical imagery: a case study in Randi Forest, Cyprus

NASA Astrophysics Data System (ADS)

Papoutsa, C.; Kouhartsiouk, D.; Themistocleous, K.; Christoforou, M.; Hadjimitsis, D. G.

2016-10-01

This paper examines how radar and optical imagery combined can be employed for the study of land degradation. A case study was conducted in the Randi Forest, Cyprus, a known overgrazed area for the past 70 years. Satellite optical imagery was used for the calculation of the Normalised Difference Vegetation Index (NDVI) for the time period between December 2015 to July 2016 and C-Band Synthetic Aperture Radar imagery was used to derive correlative changes in backscatter intensity (σ0). The results are indicative of the overgrazing in the area with the temporal and spatial variations of grazing defined. Both the NDVI and the σ0 values demonstrate sudden shifts in vegetation cover following the start of the grazing period with the greatest shifts being evident in close proximity to the location of farms. NDVI and backscatter coefficient correlation was measured at 0.7 and 0.8 for the months of February and April respectively. Shifts in NDVI value by 0.1 correspond to a shift in σ0 by 4 db. VH cross-polarization showed greater sensitivity to changes in vegetation than VV. The paper also examines the capability of C-Band Synthetic Aperture Radar to measure changes in plant structure and vegetation fraction as the result of grazing. Depending on grazing intensity, backscatter coefficient varies according to vegetation density.

CALIPSO Observations of Stratospheric Aerosols: A Preliminary Assessment

NASA Technical Reports Server (NTRS)

Thomason, Larry W.; Pitts, Michael C.; Winker, David M.

2007-01-01

We have examined the 532-nm aerosol backscatter coefficient measurements by the Cloud- Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) for their use in the observation of stratospheric aerosol. CALIPSO makes observations that span from 82 S to 82 N each day and, for each profile, backscatter coefficient values reported up to approx. 40 km. The possibility of using CALIPSO for stratospheric aerosol observations is demonstrated by the clear observation of the 20 May 2006 eruption of Montserrat in the earliest CALIPSO data in early June as well as by observations showing the 7 October 2006 eruption of Tavurvur (Rabaul). However, the very low aerosol loading within the stratosphere makes routine observations of the stratospheric aerosol far more difficult than relatively dense volcanic plumes. Nonetheless, we found that averaging a complete days worth of nighttime only data into 5-deg latitude by 1-km vertical bins reveals a stratospheric aerosol data centered near an altitude of 20 km, the clean wintertime polar vortices, and a small maximum in the lower tropical stratosphere. However, the derived values are clearly too small and often negative in much of the stratosphere. The data can be significantly improved by increasing the measured backscatter (molecular and aerosol) by approximately 5% suggesting that the current method of calibrating to a pure molecular atmosphere at 30 km is most likely the source of the low values.

Raman Lidar Observations of a MCS in the frame of the Convective and Orographically-induced Precipitation Study

NASA Astrophysics Data System (ADS)

Di Girolamo, Paolo; Bhawar, Rohini; Summa, Donato; Di Iorio, Tatiana; Demoz, Belay B.

2009-03-01

The Raman lidar system BASIL was deployed in Achern (Supersite R, Lat: 48.64° N, Long: 8.06° E, Elev.: 140 m) in the frame of the Convective and Orographically-induced Precipitation Study. On 20 July 2007 a frontal zone passed over the COPS region, with a Mesoscale Convective System (MCS) imbedded in it. BASIL was operated continuously during this day, providing measurements of temperature, water vapour, particle backscattering coefficient at 355, 532 and 1064 nm, particle extinction coefficient at 355 and 532 nm and particle depolarization at 355 and 532 nm. The thunderstorm approaching determined the lowering of the anvil clouds, which is clearly visible in the lidar data. A cloud deck is present at 2 km, which represents a mid-level outflow from the thunderstorm/MCS. The mid-level outflow spits out hydrometeor-debris (mostly virga) and it is recycled back into it. The MCS modified the environment at 1.6-2.5 km levels directly (outflow) and the lower levels through the virga/precipitation. Wave structures were observed in the particle backscatter data. The wave activity seems to be a reflection of the shear that is produced by the MCS and the inflow environmental wind. Measurements in terms of particle backscatter and water vapour mixing ratio are discussed to illustrate the above phenomena.

Anisotropy of the apparent frequency dependence of backscatter in formalin fixed human myocardium.

PubMed

Hall, C S; Verdonk, E D; Wickline, S A; Perez, J E; Miller, J G

1997-01-01

Measurements of the frequency dependence of ultrasonic backscatter are presented for specific angles of insonification for regions of infarcted and noninfarcted human myocardium. A 5-MHz transducer was used to insonify cylindrical cores taken from 7 noninfarcted regions and 12 infarcted regions of the left ventricular free wall of 6 formalin-fixed human hearts explanted because of ischemic cardiomyopathy. The dependence of apparent (uncompensated for diffraction effects and attenuation) backscatter on frequency was approximated by a power-law dependence, magnitude of B(f)2 = afn. Under ideal conditions in a lossless medium, the effect of not compensating for the effects of diffraction and attenuation leads to the value of n to be 2.0 for Rayleigh scatterers while the frequency dependence of the fully compensated backscatter coefficient would be f4. The value of n was determined over the frequency range, 3-7 MHz. Both nonifarcted and infarcted myocardium exhibited anisotropy of the frequency dependence of backscatter, with maxima occurring at angles that were perpendicular to the predominant myofiber direction and minima when parallel to the fibers. Perpendicular insonification yielded results for n of 1.8 +/- 0.1 for noninfarcted myocardium and 1.2 +/- 0.1 for infarcted myocardium while parallel insonification yielded results of 0.4 +/- 0.1 for noninfarcted and 0.0 +/- 0.1 for infarcted myocardium. The functional form of the angle-dependent backscatter is similar for both noninfarcted and infarcted myocardium, although the frequency dependence is clearly different for both tissue states for all angles of insonification. The results of this study indicate that the anisotropy of the frequency dependence of backscatter may play a significant role in ultrasonic imaging and is an important consideration for ultrasonic tissue characterization in myocardium.

Study of cerium diffusion in undoped lithium-6 enriched glass with Rutherford backscattering spectrometry

NASA Astrophysics Data System (ADS)

Zhang, Xiaodong; Moore, Michael E.; Lee, Kyung-Min; Lukosi, Eric D.; Hayward, Jason P.

2016-07-01

Undoped lithium-6 enriched glasses coated with pure cerium (99.9%) with a gold protection layer on top were heated at three different temperatures (500, 550, and 600 °C) for varied durations (1, 2, and 4 h). Diffusion profiles of cerium in such glasses were obtained with the conventional Rutherford backscattering technique. Through fitting the diffusion profiles with the thin-film solution of Fick's second law, diffusion coefficients of cerium with different annealing temperatures and durations were solved. Then, the activation energy of cerium for the diffusion process in the studied glasses was found to be 114 kJ/mol with the Arrhenius equation.

A noncoherent model for microwave emissions and backscattering from the sea surface

NASA Technical Reports Server (NTRS)

Wu, S. T.; Fung, A. K.

1973-01-01

The two-scale (small irregularities superimposed upon large undulations) scattering theory proposed by Semyonov was extended and used to compute microwave apparent temperature and the backscattering cross section from ocean surfaces. The effect of the small irregularities upon the scattering characteristics of the large undulations is included by modifying the Fresnel reflection coefficients; whereas the effect of the large undulations upon those of the small irregularities is taken into account by averaging over the surface normals of the large undulations. The same set of surface parameters is employed for a given wind speed to predict both the scattering and the emission characteristics at both polarizations.

SATCOM antenna siting study on a P-3C using the NEC-BSC V3.1

NASA Technical Reports Server (NTRS)

Bensman, D.; Marhefka, R. J.

1990-01-01

The location of a UHF SATCOM antenna on a P-3C aircraft is studied using the NEC-Basic Scattering Code V3.1 (NEC-BSC3). The NEC-BSC3 is a computer code based on the uniform theory of diffraction. The code is first validated for this application using scale model measurements. In general, the comparisons are good except in 10 degree regions near the nose and tail of the aircraft. Patterns for various antenna locations are analyzed to achieve a prescripted performance.

An Evaluation of Treatment Patterns and Outcomes in Elderly Patients Newly Diagnosed With Acute Myeloid Leukemia: A Retrospective Analysis of Electronic Medical Records From US Community Oncology Practices.

PubMed

Ma, Esprit; Bonthapally, Vijayveer; Chawla, Anita; Lefebvre, Patrick; Swords, Ronan; Lafeuille, Marie-Hélène; Fortier, Jonathan; Emond, Bruno; Duh, Mei Sheng; Dezube, Bruce J

2016-11-01

Many elderly patients with acute myeloid leukemia (AML) are considered ineligible for standard intensive induction therapy due to performance status and comorbidities. We analyzed treatment patterns and outcomes among elderly patients newly diagnosed with AML in the US community oncology setting. A retrospective observational study was conducted using patient-level data from a network of US community oncology practices provided by Altos Solutions. Patients aged ≥ 60 years, diagnosed with AML between November 2005 and February 2014, with ≥ 1 recorded visit and ≥ 6 months between diagnosis and data cutoff, were included. Only patients who received active treatment or best supportive care (BSC) per National Comprehensive Cancer Network (NCCN) AML Guidelines were analyzed. Of 1139 patients meeting the inclusion criteria, 922 (median age 76 years) received NCCN-recommended treatments: standard induction (n = 5), low-intensity therapy (n = 425), BSC with hydroxyurea (HU) (n = 36), or BSC without HU (n = 455). For the low-intensity therapy cohort, median time from diagnosis to treatment initiation was 17 days; median duration of therapy was 5.1 months. Median overall survival (OS) from diagnosis in the low-intensity, BSC with HU, and BSC without HU groups was 12.3, 7.0, and 49.4 months, respectively. Median time to next therapy/death was 10.1 months in patients receiving low-intensity therapy. A higher proportion of patients receiving low-intensity therapy required transfusion or other supportive care versus those receiving BSC. As expected, OS in patients receiving low-intensity therapy or BSC with HU is poor for elderly patients with AML. Remarkably, intensive induction strategies are rarely used for older patients in community oncology practice. Copyright © 2016 The Author(s). Published by Elsevier Inc. All rights reserved.

Matched-Pair Comparison of Radioembolization Plus Best Supportive Care Versus Best Supportive Care Alone for Chemotherapy Refractory Liver-Dominant Colorectal Metastases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seidensticker, Ricarda, E-mail: ricarda.seidensticker@med.ovgu.de; Denecke, Timm; Kraus, Patrick

2012-10-15

Purpose: This study was designed to evaluate overall survival after radioembolization or best supportive care (BSC) in patients with chemotherapy-refractory liver-dominant metastatic colorectal cancer (mCRC). Methods: This was a matched-pair comparison of patients who received radioembolization plus BSC or BSC alone for extensive liver disease. Twenty-nine patients who received radioembolization were retrospectively matched with a contemporary cohort of >500 patients who received BSC from 3 centers in Germany. Using clinical databases, patients were initially matched for prior treatments and tumor burden and then 29 patients were consecutively identified with two or more of four matching criteria: synchronous/metachronous metastases, tumor burden,more » increased ALP, and/or CEA >200 U/ml. Survival was calculated from date of progression before radioembolization or BSC by using Kaplan-Meier analysis. Results: Of 29 patients in each study arm, 16 pairs (55.2%) matched for all four criteria, and 11 pairs (37.9%) matched three criteria. Patients in both groups had a similar performance status (Karnofsky index, median 80% [range, 60-100%]). Compared with BSC alone, radioembolization prolonged survival (median, 8.3 vs. 3.5 months; P < 0.001) with a hazard ratio of 0.3 (95% confidence interval, 0.16-0.55; P < 0.001) in a multivariate Cox proportional hazard model. Treatment-related adverse events following radioembolization included: grade 1-2 fatigue (n = 20, 69%), grade 1 abdominal pain/nausea (n = 14, 48.3%), and grade 2 gastrointestinal ulceration (n = 3, 10.3%). Three cases of grade 3 radiation-induced liver disease were symptomatically managed. Conclusions: Radioembolization offers a promising addition to BSC in treatment-refractory patients for whom there are limited options. Survival was prolonged and adverse events were generally mild-to-moderate in nature and manageable.« less

Air flow optimization for energy efficient blower of biosafety cabinet class II A2

NASA Astrophysics Data System (ADS)

Ibrahim, M. D.; Mohtar, M. Z.; Alias, A. A.; Wong, L. K.; Yunos, Y. S.; Rahman, M. R. A.; Zulkharnain, A.; Tan, C. S.; Thayan, R.

2017-04-01

An energy efficient Biosafety Cabinet (BSC) has become a big challenge for manufacturers to develop BSC with the highest level of protection. The objective of research is to increase air flow velocity discharge from centrifugal blower. An aerodynamic duct shape inspired by the shape of Peregrine Falcon’s wing during diving flight is added to the end of the centrifugal blower. Investigation of air movement is determined by computational fluid dynamics (CFD) simulation. The results showed that air velocity can be increased by double compared to typical manufactured BSC and no air recirculation. As conclusion, a novel design of aerodynamic duct shape successfully developed and proved that air velocity can be increase naturally with same impeller speed. It can contribute in increasing energy efficiency of the centrifugal blower. It is vital to BSC manufacturer and can be apply to Heating, Air Ventilation and Air Conditioning (HVAC) industries.

Use of Self-Organizing Maps for Balanced Scorecard analysis to monitor the performance of dialysis clinic chains.

PubMed

Cattinelli, Isabella; Bolzoni, Elena; Barbieri, Carlo; Mari, Flavio; Martin-Guerrero, José David; Soria-Olivas, Emilio; Martinez-Martinez, José Maria; Gomez-Sanchis, Juan; Amato, Claudia; Stopper, Andrea; Gatti, Emanuele

2012-03-01

The Balanced Scorecard (BSC) is a validated tool to monitor enterprise performances against specific objectives. Through the choice and the evaluation of strategic Key Performance Indicators (KPIs), it provides a measure of the past company's outcome and allows planning future managerial strategies. The Fresenius Medical Care (FME) BSC makes use of 30 KPIs for a continuous quality improvement strategy within its dialysis clinics. Each KPI is monthly associated to a score that summarizes the clinic efficiency for that month. Standard statistical methods are currently used to analyze the BSC data and to give a comprehensive view of the corporate improvements to the top management. We herein propose the Self-Organizing Maps (SOMs) as an innovative approach to extrapolate information from the FME BSC data and to present it in an easy-readable informative form. A SOM is a computational technique that allows projecting high-dimensional datasets to a two-dimensional space (map), thus providing a compressed representation. The SOM unsupervised (self-organizing) training procedure results in a map that preserves similarity relations existing in the original dataset; in this way, the information contained in the high-dimensional space can be more easily visualized and understood. The present work demonstrates the effectiveness of the SOM approach in extracting useful information from the 30-dimensional BSC dataset: indeed, SOMs enabled both to highlight expected relationships between the KPIs and to uncover results not predictable with traditional analyses. Hence we suggest SOMs as a reliable complementary approach to the standard methods for BSC interpretation.

Backscattering analysis of high frequency ultrasonic imaging for ultrasound-guided breast biopsy

NASA Astrophysics Data System (ADS)

Cummins, Thomas; Akiyama, Takahiro; Lee, Changyang; Martin, Sue E.; Shung, K. Kirk

2017-03-01

A new ultrasound-guided breast biopsy technique is proposed. The technique utilizes conventional ultrasound guidance coupled with a high frequency embedded ultrasound array located within the biopsy needle to improve the accuracy in breast cancer diagnosis.1 The array within the needle is intended to be used to detect micro- calcifications indicative of early breast cancers such as ductal carcinoma in situ (DCIS). Backscattering analysis has the potential to characterize tissues to improve localization of lesions. This paper describes initial results of the application of backscattering analysis of breast biopsy tissue specimens and shows the usefulness of high frequency ultrasound for the new biopsy related technique. Ultrasound echoes of ex-vivo breast biopsy tissue specimens were acquired by using a single-element transducer with a bandwidth from 41 MHz to 88 MHz utilizing a UBM methodology, and the backscattering coefficients were calculated. These values as well as B-mode image data were mapped in 2D and matched with each pathology image for the identification of tissue type for the comparison to the pathology images corresponding to each plane. Microcalcifications were significantly distinguished from normal tissue. Adenocarcinoma was also successfully differentiated from adipose tissue. These results indicate that backscattering analysis is able to quantitatively distinguish tissues into normal and abnormal, which should help radiologists locate abnormal areas during the proposed ultrasound-guided breast biopsy with high frequency ultrasound.

Study of MPLNET-Derived Aerosol Climatology over Kanpur, India, and Validation of CALIPSO Level 2 Version 3 Backscatter and Extinction Products

NASA Technical Reports Server (NTRS)

Misra, Amit; Tripathi, S. N.; Kaul, D. S.; Welton, Ellsworth J.

2012-01-01

The level 2 aerosol backscatter and extinction profiles from the NASA Micropulse Lidar Network (MPLNET) at Kanpur, India, have been studied from May 2009 to September 2010. Monthly averaged extinction profiles from MPLNET shows high extinction values near the surface during October March. Higher extinction values at altitudes of 24 km are observed from April to June, a period marked by frequent dust episodes. Version 3 level 2 Cloud Aerosol Lidar with Orthogonal Polarization (CALIOP) aerosol profile products have been compared with corresponding data from MPLNET over Kanpur for the above-mentioned period. Out of the available backscatter profiles, the16 profiles used in this study have time differences less than 3 h and distances less than 130 km. Among these profiles, four cases show good comparison above 400 m with R2 greater than 0.7. Comparison with AERONET data shows that the aerosol type is properly identified by the CALIOP algorithm. Cloud contamination is a possible source of error in the remaining cases of poor comparison. Another source of error is the improper backscatter-to-extinction ratio, which further affects the accuracy of extinction coefficient retrieval.

Monte Carlo investigation of backscatter factors for skin dose determination in interventional neuroradiology procedures

NASA Astrophysics Data System (ADS)

Omar, Artur; Benmakhlouf, Hamza; Marteinsdottir, Maria; Bujila, Robert; Nowik, Patrik; Andreo, Pedro

2014-03-01

Complex interventional and diagnostic x-ray angiographic (XA) procedures may yield patient skin doses exceeding the threshold for radiation induced skin injuries. Skin dose is conventionally determined by converting the incident air kerma free-in-air into entrance surface air kerma, a process that requires the use of backscatter factors. Subsequently, the entrance surface air kerma is converted into skin kerma using mass energy-absorption coefficient ratios tissue-to-air, which for the photon energies used in XA is identical to the skin dose. The purpose of this work was to investigate how the cranial bone affects backscatter factors for the dosimetry of interventional neuroradiology procedures. The PENELOPE Monte Carlo system was used to calculate backscatter factors at the entrance surface of a spherical and a cubic water phantom that includes a cranial bone layer. The simulations were performed for different clinical x-ray spectra, field sizes, and thicknesses of the bone layer. The results show a reduction of up to 15% when a cranial bone layer is included in the simulations, compared with conventional backscatter factors calculated for a homogeneous water phantom. The reduction increases for thicker bone layers, softer incident beam qualities, and larger field sizes, indicating that, due to the increased photoelectric crosssection of cranial bone compared to water, the bone layer acts primarily as an absorber of low-energy photons. For neurointerventional radiology procedures, backscatter factors calculated at the entrance surface of a water phantom containing a cranial bone layer increase the accuracy of the skin dose determination.

Feasibility of inter-comparing airborne and spaceborne observations of radar backscattering coefficients

USDA-ARS?s Scientific Manuscript database

This paper investigates the feasibility of using an airborne synthetic aperture radar (SAR) to validate spaceborne SAR data. This is directed at soil moisture sensing and the recently launched Soil Moisture Active Passive (SMAP) satellite. The value of this approach is related to the fact that vicar...

Finnish Meteorological Institute Doppler Lidar

DOE Data Explorer

Ewan OConnor

2015-03-27

This doppler lidar system provides co-polar and cross polar attenuated backscatter coefficients,signal strength, and doppler velocities in the cloud and in the boundary level, including uncertainties for all parameters. Using the doppler beam swinging DBS technique, and Vertical Azimuthal Display (VAD) this system also provides vertical profiles of horizontal winds.

ESTIMATION OF INHERENT OPTICAL PROPERTIES AND WATER CONSTITUENT CONCENTRATIONS FROM THE REMOTE-SENSING REFLECTANCE SPECTRA IN THE ALBEMARLE-PAMLICO ESTUARY, USA

EPA Science Inventory

The decomposition of remote sensing reflectance (RSR) spectra into absorption, scattering and backscattering coefficients, and scattering phase function is an important issue for estimating water quality (WQ) components. For Case 1 waters RSR decomposition can be easily accompli...

Combined active and passive microwave remote sensing of vegetated surfaces at l-band

USDA-ARS?s Scientific Manuscript database

In previous work the distorted Born approximation (DBA) of volume scattering was combined with the numerical solutions of Maxwell equations (NMM3D) for a rough surface to calculate the radar backscattering coefficient for the Soil Moisture Active Passive (SMAP) mission. The model results were valida...

Soil stabilization by biological soil crusts in arid Tunisia

NASA Astrophysics Data System (ADS)

Guidez, Sabine; Couté, Alain; Bardat, Jacques

2015-04-01

As part of the fight against desertification (LCD) in arid Tunisia, we have been able to highlight the important role played by biological soil crusts (BSC) in soil stabilization. The identification of the major species of cyanobacteria, lichens and bryophytes, their adaptation and terrestrial colonization strategies in this high climatic constraints area through their morpho-anatomical criteria have been set. In addition to their biological composition, their internal arrangement (i.e. texture and microstructure) reflects the structural stability of BSC against erosion. Precisely, the aggregative power of cyanobacteria and their ways of moving inside a soil, the capacity of mosses to grow through the sediments and lichens ability to bind at particles on surface, thus stabilizing the substrate have been demonstrated. Then, the three biological components ability to capture soil particles has been widely illustrated, proving the major environmental contribution of BSC in arid areas biological crusts formation, providing that soils will experience an increase of organic matter and fine particles rates subsequently gaining faster and better stability. Although the thickness and the morphology of crusts are related to the cover rates of these different biological components, the water properties of the latter, studied at the environmental SEM, illustrate their important role in altering the water cycle. Thus, the mixed crusts, i.e. with good presence of three biological components, cause the highest runoff rates by their ability to retain the water and spread on the surface. In spite of a swelling coefficient in presence of water higher than cryptogams, the cyanobacterial crusts located in newly stabilized areas of our studied region, remain finally insufficiently dense to impact surface hydrology. But, we showed after all that the cyanobacteria, pioneer species, have a certain environmental role. The lichen crusts cause a increased runoff because the lichens have a ability to extend them horizontally on the soil surface. Despite the water capture for their metabolism, the water flows; it isn't released in the depth. The moss crusts show an opposite process with an increased infiltration thanks to the possibility of a vertical transit of water through their sheets, stem and roots. So, in relation to bare soils, a crust with a good microbial and cryptogamic development causes more runoff. As part of the fight against the desertification in arid Tunisia, hydrological impact of BSC may lead to elaborate some ecosystem strategies in water and soils management. Indeed, climate aridity is not synonymous with edaphic aridity.

A New GaAs Laser Radar for Atmospheric Measurements

NASA Technical Reports Server (NTRS)

Brown, R. T.; Stoliar, A. P.

1973-01-01

A special GaAs lidar using fiber coupled diode lasers was constructed for the purpose of measuring the extinction coefficient distribution within a large atmospheric volume at a rate compatible with atmospheric kinematics. The technique is based on taking backscatter signature ratios over spatial increments after the returns are normalized by pulse integration. Essential aspects of the lidar design are beam pulse power, repetition rate, detection system dynamic range and decay linearity. It was necessary to preclude the possibility of eye hazard under any operating conditions, including directly viewing the emitting aperture at close distance with a night-adapted eye. The electronic signal processing and control circuits were built to allow versatile operations. Extinction coefficient measurements were made in fog and clouds using a low-power laboratory version of the lidar, demonstrating feasibility. Data are presented showing range squared corrected backscatter profiles converted to extinction coefficient profiles, temporal signal fluctuations, and solar induced background noise. These results aided in the design of the lidar which is described. Functional tests of this lidar and the implications relevant to the design of a prototype model are discussed. This work was jointly sponsored by Sperry Rand Corporation under its Independent Research and Development program; the Air Force Avionics Laboratory, Wright Field, Dayton, Ohio; and the Naval Ammunition Depot, Crane, Indiana.

Service quality in contracted facilities.

PubMed

Rabbani, Fauziah; Pradhan, Nousheen Akber; Zaidi, Shehla; Azam, Syed Iqbal; Yousuf, Farheen

2015-01-01

The purpose of this paper is to explore the readiness of contracted and non-contracted first-level healthcare facilities in Pakistan to deliver quality maternal and neonatal health (MNH) care. A balanced scorecard (BSC) was used as the assessment framework. Using a cross-sectional study design, two rural health centers (RHCs) contracted out to Aga Khan Health Service, Pakistan were compared with four government managed RHCs. A BSC was designed to assess RHC readiness to deliver good quality MNH care. In total 20 indicators were developed, representing five BSC domains: health facility functionality, service provision, staff capacity, staff and patient satisfaction. Validated data collection tools were used to collect information. Pearson χ2, Fisher's Exact and the Mann-Whitney tests were applied as appropriate to detect significant service quality differences among the two facilities. Contracted facilities were generally found to be better than non-contracted facilities in all five BSC domains. Patients' inclination for facility-based delivery at contracted facilities was, however, significantly higher than non-contracted facilities (80 percent contracted vs 43 percent non-contracted, p=0.006). The study shows that contracting out initiatives have the potential to improve MNH care. This is the first study to compare MNH service delivery quality across contracted and non-contracted facilities using BSC as the assessment framework.

Monitoring of the Liquid Water Content During Snowmelt Using C-Band SAR Data and the Snow Model CROCUS

NASA Astrophysics Data System (ADS)

Rondeau-Genesse, G.; Trudel, M.; Leconte, R.

2014-12-01

Coupling C-Band synthetic aperture radar (SAR) data to a multilayer snow model is a step in better understanding the temporal evolution of the radar backscattering coefficient during snowmelt. The watershed used for this study is the Nechako River Basin, located in the Rocky Mountains of British-Columbia (Canada). This basin has a snowpack of several meters in depth and part of its water is diverted to the Kemano hydropower system, managed by Rio-Tinto Alcan. Eighteen RADARSAT-2 ScanSAR Wide archive images were acquired in VV/VH polarization for the winter of 2011-2012, under different snow conditions. They are interpreted along with CROCUS, a multilayer physically-based snow model developed by Météo-France. This model discretizes the snowpack into 50 layers, which makes it possible to monitor various characteristics, such as liquid water content (LWC), throughout the season. CROCUS is used to model three specific locations of the Nechako River Basin. Results vary from one site to another, but in general there is a good agreement between the modeled LWC of the first layer of the snowpack and the backscattering coefficient of the RADARSAT-2 images, with a coefficient of determination (R²) of 0.80 and more. The radar images themselves were processed using an updated version of Nagler's methodology, which consists of subtracting an image in wet snow conditions to one in dry snow conditions, as wet snow can then be identified using a soft threshold centered around -3 dB. A second filter was used in order to differentiate dry snow and bare soil. That filter combines a VH/VV ratio threshold and an altitude criterion. The ensuing maps show a good agreement with the MODIS snow-covered area, which is already obtained daily over the Nechako River Basin, but with additional information on the location of wet snow and without sensibility to cloud cover. As a next step, the outputs of CROCUS will be used in Mätzler's Microwave Emission Model of Layered Snowpacks (MEMLS) to simulate the backscattering coefficient at different locations in the basin.

The effects of soil moisture and plant morphology on the radar backscatter from vegetation

NASA Technical Reports Server (NTRS)

Ulaby, F. T.; Bush, T. F.; Batlivala, P. P.; Cihlar, J.

1974-01-01

The results of experimental studies on the backscattering properties of corn, milo, soybeans and alfalfa are presented. The measurements were made during the summer of 1973 over the 8 to 18 GHz frequency band. The data indicate that soil moisture estimation is best accomplished at incidence angles near nadir with lower frequencies, while crop discrimination is best accomplished using two frequencies at incidence angles ranging from 30 deg to 65 deg. It is also shown that temporal plant morphology variations can cause extreme variations in the values of the scattering coefficients. These morphological changes can be caused by growth, heavy rain and in the case of alfalfa, harvesting.

Position-dependent radiative transfer as a tool for studying Anderson localization: Delay time, time-reversal and coherent backscattering

NASA Astrophysics Data System (ADS)

van Tiggelen, B. A.; Skipetrov, S. E.; Page, J. H.

2017-05-01

Previous work has established that the localized regime of wave transport in open media is characterized by a position-dependent diffusion coefficient. In this work we study how the concept of position-dependent diffusion affects the delay time, the transverse confinement, the coherent backscattering, and the time reversal of waves. Definitions of energy transport velocity of localized waves are proposed. We start with a phenomenological model of radiative transfer and then present a novel perturbational approach based on the self-consistent theory of localization. The latter allows us to obtain results relevant for realistic experiments in disordered quasi-1D wave guides and 3D slabs.

The leaf-shape effect on electromagnetic scattering from vegetated media

NASA Technical Reports Server (NTRS)

Karam, M. A.; Fung, A. K.; Blanchard, A. J.; Shen, G. X.

1988-01-01

Using the generalized Rayleigh Gans approximation along with the radiative transfer method, a bistatic backscattering model for a layer of randomly oriented, elliptic-shaped leaves is formulated. Following a similar procedure the bistatic scattering model for a layer of needle-shaped leaves is also developed to simulate coniferous vegetation. The differences between the scattering characteristics of the deciduous and coniferous leaves are illustrated numerically for different orientation and incidence angles. It is found that both like and cross polarizations are needed to differentiate the difference in scattering due to the shapes of the scatterers. The calculated backscattering coefficients are compared with measured values from artificial canopies with circular-shaped leaves.

Identification of factors influencing the restoration of cyanobacteria-dominated biological soil crusts.

PubMed

Bu, Chongfeng; Wu, Shufang; Yang, Yongsheng; Zheng, Mingguo

2014-01-01

Biological soil crusts (BSCs) cover >35% of the Earth's land area and contribute to important ecological functions in arid and semiarid ecosystems, including erosion reduction, hydrological cycling, and nutrient cycling. Artificial rapid cultivation of BSCs can provide a novel alternative to traditional biological methods for controlling soil and water loss such as the planting of trees, shrubs, and grasses. At present, little is known regarding the cultivation of BSCs in the field due to lack of knowledge regarding the influencing factors that control BSCs growth. Thus, we determined the effects of various environmental factors (shade; watering; N, P, K, and Ca concentrations) on the growth of cyanobacteria-dominated BSCs from the Sonoran Desert in the southwestern United States. The soil surface changes and chlorophyll a concentrations were used as proxies of BSC growth and development. After 4 months, five factors were found to impact BSC growth with the following order of importance: NH4NO3 ≈ watering frequency>shading>CaCO3 ≈ KH2PO4. The soil water content was the primary positive factor affecting BSC growth, and BSCs that were watered every 5 days harbored greater biomass than those watered every 10 days. Groups that received NH4NO3 consistently exhibited poor growth, suggesting that fixed N amendment may suppress BSC growth. The effect of shading on the BSC biomass was inconsistent and depended on many factors including the soil water content and availability of nutrients. KH2PO4 and CaCO3 had nonsignificant effects on BSC growth. Collectively, our results indicate that the rapid restoration of BSCs can be controlled and realized by artificial "broadcasting" cultivation through the optimization of environmental factors.

The Effects of Bushen Capsule on Episodic Memory in Amnestic Mild Cognitive Impairment Patients: A Pilot Placebo Controlled fMRI Study.

PubMed

Zhang, Junying; Xu, Kai; Wei, Dongfeng; Guo, Rongjuan; Li, He; Wang, Yongyan; Zhang, Zhanjun

2015-01-01

Observing the effects of a drug on episodic memory and the underlying brain function has extreme significance in evaluating its therapeutic value in treating amnestic mild cognitive impairment (aMCI). To observe the effects of Bushen capsule (BSC), a Chinese herbal medicine, on episodic memory in aMCI and further explore the underlying mechanism. 44 aMCI patients from hospitals and local communities in Beijing were randomly divided into the BSC treatment group (22 patients orally treated with BSC) and the placebo group (22 patients treated with placebo). The duration of intervention lasted for 3 months. Before and after the 3 months treatment, neuropsychological tests and fMRI examinations were carried out to assess cognitive ability and brain activation changes, respectively. Compared to the placebo group, the BSC group presented a significant increase in the AVLT(N5) (p = 0.003) and Stroop (C-B) time (p = 0.002). fMRI results showed a reduction of brain negative activation in the right middle temporal gyrus and a positive activation enhancement in the right putamen among the BSC group after treatment. Meanwhile, the variation in activation values in the right middle temporal gyrus was significantly correlated with the improvement in test values of AVLT(N5), and the variation in deactivation values in the right putamen was significantly correlated with the improvement in test values of Stroop (C-B) time. BSC can improve the behavioral performances of episodic memory in aMCI; this effect may be related to its modulation on the activations of the temporal lobe and the putamen under episodic memory encoding task.

Unconscious integration of multisensory bodily inputs in the peripersonal space shapes bodily self-consciousness.

PubMed

Salomon, Roy; Noel, Jean-Paul; Łukowska, Marta; Faivre, Nathan; Metzinger, Thomas; Serino, Andrea; Blanke, Olaf

2017-09-01

Recent studies have highlighted the role of multisensory integration as a key mechanism of self-consciousness. In particular, integration of bodily signals within the peripersonal space (PPS) underlies the experience of the self in a body we own (self-identification) and that is experienced as occupying a specific location in space (self-location), two main components of bodily self-consciousness (BSC). Experiments investigating the effects of multisensory integration on BSC have typically employed supra-threshold sensory stimuli, neglecting the role of unconscious sensory signals in BSC, as tested in other consciousness research. Here, we used psychophysical techniques to test whether multisensory integration of bodily stimuli underlying BSC also occurs for multisensory inputs presented below the threshold of conscious perception. Our results indicate that visual stimuli rendered invisible through continuous flash suppression boost processing of tactile stimuli on the body (Exp. 1), and enhance the perception of near-threshold tactile stimuli (Exp. 2), only once they entered PPS. We then employed unconscious multisensory stimulation to manipulate BSC. Participants were presented with tactile stimulation on their body and with visual stimuli on a virtual body, seen at a distance, which were either visible or rendered invisible. We found that participants reported higher self-identification with the virtual body in the synchronous visuo-tactile stimulation (as compared to asynchronous stimulation; Exp. 3), and shifted their self-location toward the virtual body (Exp.4), even if stimuli were fully invisible. Our results indicate that multisensory inputs, even outside of awareness, are integrated and affect the phenomenological content of self-consciousness, grounding BSC firmly in the field of psychophysical consciousness studies. Copyright © 2017 Elsevier B.V. All rights reserved.

Multidimensional evaluation of performance with experimental application of balanced scorecard: a two year experience

PubMed Central

2011-01-01

Background In today's dynamic health-care system, organizations such as hospitals are required to improve their performance for multiple stakeholders and deliver an integrated care that means to work effectively, be innovative and organize efficiently. Achieved goals and levels of quality can be successfully measured by a multidimensional approach like Balanced Scorecard (BSC). The aim of the study was to verify the opportunity to introduce BSC framework to measure performance in St. Anna University Hospital of Ferrara, applying it to the Clinical Laboratory Operative Unit in order to compare over time performance results and achievements of assigned targets. Methods In the first experience with BSC we distinguished four perspectives, according to Kaplan and Norton, identified Key Performance Areas and Key Performance Indicators, set standards and weights for each objective, collected data for all indicators, recognized cause-and-effect relationships in a strategic map. One year later we proceeded with the next data collection and analysed the preservation of framework aptitude to measure Operative Unit performance. In addition, we verified the ability to underline links between strategic actions belonging to different perspectives in producing outcomes changes. Results The BSC was found to be effective for underlining existing problems and identifying opportunities for improvements. The BSC also revealed the specific perspective contribution to overall performance enhancement. After time results comparison was possible depending on the selection of feasible and appropriate key performance indicators, which was occasionally limited by data collection problems. Conclusions The first use of BSC to compare performance at Operative Unit level, in course of time, suggested this framework can be successfully adopted for results measuring and revealing effective health factors, allowing health-care quality improvements. PMID:21586111

Multidimensional evaluation of performance with experimental application of balanced scorecard: a two year experience.

PubMed

Lupi, Silvia; Verzola, Adriano; Carandina, Gianni; Salani, Manuela; Antonioli, Paola; Gregorio, Pasquale

2011-05-17

In today's dynamic health-care system, organizations such as hospitals are required to improve their performance for multiple stakeholders and deliver an integrated care that means to work effectively, be innovative and organize efficiently. Achieved goals and levels of quality can be successfully measured by a multidimensional approach like Balanced Scorecard (BSC). The aim of the study was to verify the opportunity to introduce BSC framework to measure performance in St. Anna University Hospital of Ferrara, applying it to the Clinical Laboratory Operative Unit in order to compare over time performance results and achievements of assigned targets. In the first experience with BSC we distinguished four perspectives, according to Kaplan and Norton, identified Key Performance Areas and Key Performance Indicators, set standards and weights for each objective, collected data for all indicators, recognized cause-and-effect relationships in a strategic map. One year later we proceeded with the next data collection and analysed the preservation of framework aptitude to measure Operative Unit performance. In addition, we verified the ability to underline links between strategic actions belonging to different perspectives in producing outcomes changes. The BSC was found to be effective for underlining existing problems and identifying opportunities for improvements. The BSC also revealed the specific perspective contribution to overall performance enhancement. After time results comparison was possible depending on the selection of feasible and appropriate key performance indicators, which was occasionally limited by data collection problems. The first use of BSC to compare performance at Operative Unit level, in course of time, suggested this framework can be successfully adopted for results measuring and revealing effective health factors, allowing health-care quality improvements.

Local knowledge and perception of biological soil crusts by land users in the Sahel (Niger)

NASA Astrophysics Data System (ADS)

J-M Ambouta, K.; Hassan Souley, B.; Malam Issa, O.; Rajot, J. L.; Mohamadou, A.

2012-04-01

Local knowledge, i.e. knowledge based on accumulation of observations is of great interest for many scientific fields as it can help for identification, evaluation and selection of relevant indicators and furthermore for progress through conservation goals. This study aimed at gathering and understanding the local knowledge and perception of biological soil crusts (BSC) by users of land, pastoralists that cross the Sahel and sedentary farmers. The methodological approach is based on a semi-direct surveys conducted on a north-south rainfall gradient (350 to 650 mm/year) including agricultural- and pastoral-dominated areas in western Niger. Denomination, formation processes, occurrence, distribution and role of biological soil crusts are among the major issues of the inquiry. The results of the surveys showed that BSC are mainly identified by the names of "Bankwado" and "Korobanda", respectively in hausa and zarma langages, what means "toad back". Other denominations varying according to region, ethnic groups and users are used. They are all related to the aspects, colors and behaviour of BSC with regard wetting and drying cycle. From the point of view of users depressed areas and land lied fallow are favourable places for the occurrence of BSC, while cultivation and observed changes in rainfall regimes represent negative factors. The formation processes of BSC are mainly related to the occurrence and the impact of rain and wind on soil surface. Their roles in protecting soil against degradation or as an indicator of soil fertility were recognised by at least 83% of farmers and breeders. This study reveals significant aspects of BSC already validated by scientific knowledge. Integrating the two forms of knowledge will help to define relevant indicators of soil surface dynamics and to perform practices to minimize farming and grazing impacts on BSCs.

A New Approach for Checking and Complementing CALIPSO Lidar Calibration

NASA Technical Reports Server (NTRS)

Josset, Damien B.; Vaughan, Mark A.; Hu, Yongxiang; Avery, Melody A.; Powell, Kathleen A.; Hunt, William H.; Winker, David M.; Pelon, Jacques; Trepte, Charles R.; Lucker, Patricia L.;

Assessing The Response Of Alpine Natura 2000 Habitat Changes By Using Dual Polarized (VV/VH) COSMO-SkyMed Imagery

NASA Astrophysics Data System (ADS)

Spindler, N.; Polychronaki, A.; Notarnicola, C.

2013-12-01

Grasslands cover nearly one quarter of the earth's surface. They are not only a habitat for a diversity of species and therefore an important focus in the Natura 2000 framework but also a crucial factor in the scope of food security and the associated crop estimation as a forage base. Since both topics are strongly linked they are addressed in this study with two main objectives using weather independent satellite data. Initially, we aimed to understand the backscatter mechanism of COSMO-SkyMed X-band dual pol using two different incidence angles for selected Natura conservation sites. In a second step, we then related the backscatter coefficients to a MODIS LAI product. Results indicated a separation potential for different Natura 2000 grasslands types with a difference of 2dB. The associated backscatter signal with the LAI data demonstrated a good correlation values for natural grasslands using low incidence angles.

Reflection and backscattering of microwaves under doubling of the plasma density and displacement of the gyroresonance region during electron cyclotron resonance heating of plasma in the l-2M stellarator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Batanov, G. M.; Borzosekov, V. D.; Vasilkov, D. G.

Reflection and backscattering of high-power (400 kW) gyrotron radiation creating and heating plasma at the second harmonic of the electronic cyclotron frequency in the L-2M stellarator have been investigated experimentally. The effect of the displacement of the gyroresonance region from the axis of the plasma column under doubling of the plasma density on the processes of reflection and backscattering of microwave radiation has been examined. A near doubling of short-wavelength (k{sub ⊥} ≈ 30 cm{sup –1}) turbulent density fluctuations squared is observed. The change in the energy confinement time under variations of plasma parameters and characteristics of short-wavelength turbulence ismore » discussed. A discrepancy between the measured values of the reflection coefficient from the electron cyclotron resonance heating region and predictions of the one-dimensional model is revealed.« less

Coherence of particulate beam attenuation and backscattering coefficients in diverse open ocean environments.

PubMed

Westberry, Toby K; Dall'Olmo, Giorgio; Boss, Emmanuel; Behrenfeld, Michael J; Moutin, Thierry

2010-07-19

We present an extensive data set of particle attenuation (c(p)), backscattering (b(bp)), and chlorophyll concentration (Chl) from a diverse set of open ocean environments. A consistent observation in the data set is the strong coherence between c(p) and b(bp) and the resulting constancy of the backscattering ratio (0.010 +/- 0.002). The strong covariability between c(p) and b(bp) must be rooted in one or both of two explanations, 1) the size distribution of particles in the ocean is remarkably conserved and particle types responsible for c(p) and b(bp) covary, 2) the same particle types exert influence on both quantities. Therefore, existing relationships between c(p) or Chl:c(p) and phytoplankton biomass and physiological indices can be conceptually extended to the use of b(bp). This finding lends support to use of satellite-derived Chl and b(bp) for investigation of phytoplankton biomass and physiology and broadens the applications of existing ocean color retrievals.

Performance Management in Healthcare Organizations: Concept and Practicum.

PubMed

Dimitropoulos, Panagiotis E

2017-01-01

Organizational performance can create and sustain competitive advantages for corporations and even improve their sustainability and future prospects. Health care organizations present a sector where performance management is structured by multiple dimensions. The scope of this study is to analyze the issue of performance management in healthcare organizations and specifically the implementation of the Balanced Scorecard (BSC) methodology on organizations providing health services. The study provides a discussion on the BSC development process, the steps that management has to take in order to prepare the implementation of the BSC and finally discusses a practical example of a scorecard with specific strategic goals and performance indicators. Managers of healthcare organizations and specifically those providing services to the elderly and the general population could use the propositions of the study as a roadmap for processing, analyzing, evaluating and implementing the balanced scorecard approach in their organizations' daily operations. BSC methodology can give an advantage in terms of enhanced stakeholder management and preservation within a highly volatile and competitive economic environment.

Simulation of the mineral dust emission over Northern Africa and Middle East using an aerodynamic roughness length map derived from the ASCAT/PARASOL

NASA Astrophysics Data System (ADS)

Basart, Sara; Jorba, Oriol; Pérez García-Pando, Carlos; Prigent, Catherine; Baldasano, Jose M.

2014-05-01

Aeolian aerodynamic roughness length in arid regions is a key parameter to predict the vulnerability of the surface to wind erosion, and, as a consequence, the related production of mineral aerosol (e.g. Laurent et al., 2008). Recently, satellite-derived roughness length at the global scale have emerged and provide the opportunity to use them in advanced emission schemes in global and regional models (i.e. Menut et al., 2013). A global map of the aeolian aerodynamic roughness length at high resolution (6 km) is derived, for arid and semi-arid regions merging PARASOL and ASCAT data to estimate aeolian roughness length. It shows very good consistency with the existing information on the properties of these surfaces. The dataset is available to the community, for use in atmospheric dust transport models. The present contribution analyses the behaviour of the NMMB/BSC-Dust model (Pérez et al., 2011) when the ASCAT/PARASOL satellite-derived global roughness length (Prigent et al, 2012) and the State Soil Geographic database Food and Agriculture Organization of the United Nations (STATSGO-FAO) soil texture data set (based on wet techniques) is used. We explore the sensitivity of the drag partition scheme (a critical component of the dust emission scheme) and the dust vertical fluxes (intensity and spatial patterns) to the roughness length. An annual evaluation of NMMB/BSC-Dust (for the year 2011) over Northern Africa and the Middle East using observed aerosol optical depths (AODs) from Aerosol Robotic Network sites and aerosol satellite products (MODIS and MISR) will be discussed. Laurent, B., Marticorena, B., Bergametti, G., Leon, J. F., and Mahowald, N. M.: Modeling mineral dust emissions from the Sahara desert using new surface properties and soil database, J. Geophys. Res., 113, D14218, doi:10.1029/2007JD009484, 2008. Menut, L., C. Pérez, K. Haustein, B. Bessagnet, C. Prigent, and S. Alfaro, Impact of surface roughness and soil texture on mineral dust emission fluxes modeling, J. Geophys. Res. Atmos., 118, 6505-6520, doi:10.1002/jgrd.50313, 2013. Pérez, C., Haustein, K., Janjic, Z., Jorba, O., Huneeus, N., Baldasano, J. M. and Thomson, M. Atmospheric dust modeling from meso to global scales with the online NMMB/BSC-Dust model-Part 1: Model description, annual simulations and evaluation. Atmospheric Chemistry and Physics, 11(24), 13001-13027, 2011. Prigent, C., Jiménez, C., and Catherinot, J.: Comparison of satellite microwave backscattering (ASCAT) and visible/near-infrared reflectances (PARASOL) for the estimation of aeolian aerodynamic roughness length in arid and semi-arid regions, Atmos. Meas. Tech., 5, 2703-2712, doi:10.5194/amt-5-2703-2012, 2012.

Absolute calibration of the Jenoptik CHM15k-x ceilometer and its applicability for quantitative aerosol monitoring

NASA Astrophysics Data System (ADS)

Geiß, Alexander; Wiegner, Matthias

2014-05-01

The knowledge of the spatiotemporal distribution of atmospheric aerosols and its optical characterization is essential for the understanding of the radiation budget, air quality, and climate. For this purpose, lidar is an excellent system as it is an active remote sensing technique. As multi-wavelength research lidars with depolarization channels are quite complex and cost-expensive, increasing attention is paid to so-called ceilometers. They are simple one-wavelength backscatter lidars with low pulse energy for eye-safe operation. As maintenance costs are low and continuous and unattended measurements can be performed, they are suitable for long-term aerosol monitoring in a network. However, the signal-to-noise ratio is low, and the signals are not calibrated. The only optical property that can be derived from a ceilometer is the particle backscatter coefficient, but even this quantity requires a calibration of the signals. With four years of measurements from a Jenoptik ceilometer CHM15k-x, we developed two methods for an absolute calibration on this system. This advantage of our approach is that only a few days with favorable meteorological conditions are required where Rayleigh-calibration and comparison with our research lidar is possible to estimate the lidar constant. This method enables us to derive the particle backscatter coefficient at 1064 nm, and we retrieved for the first time profiles in near real-time within an accuracy of 10 %. If an appropriate lidar ratio is assumed the aerosol optical depth of e.g. the mixing layer can be determined with an accuracy depending on the accuracy of the lidar ratio estimate. Even for 'simple' applications, e.g. assessment of the mixing layer height, cloud detection, detection of elevated aerosol layers, the particle backscatter coefficient has significant advantages over the measured (uncalibrated) attenuated backscatter. The possibility of continuous operation under nearly any meteorological condition with temporal resolution in the order of 30 seconds makes it also possible to apply time-height-tracking methods for detecting mixing layer heights. The combination of methods for edge detection (e.g. wavelet covariance transform, gradient method, variance method) and edge tracking techniques is used to increase the reliability of the layer detection and attribution. Thus, a feature mask of aerosols and clouds can be derived. Four years of measurements constitute an excellent basis for a climatology including a homogeneous time series of mixing layer heights, aerosol layers and cloud base heights of the troposphere. With a low overlap region of 180 m of the Jenoptik CHM15k-x even very narrow mixing layers, typical for winter conditions, can be considered.

Application of the Kano-Hamilton multiangle inversion method in clear atmospheres

Treesearch

Mariana Adam; Vladimir A. Kovalev; Cyle Wold; Jenny Newton; Markus Pahlow; Wei M. Hao; Marc B. Parlange

2007-01-01

An improved measurement methodology and a data-processing technique for multiangle data obtained with an elastic scanning lidar in clear atmospheres are introduced. Azimuthal and slope scans are combined to reduce the atmospheric heterogeneity. Vertical profiles of optical depth and intercept (proportional to the logarithm of the backscatter coefficient) are determined...

Application of an optimization algorithm to satellite ocean color imagery: A case study in Southwest Florida coastal waters

NASA Astrophysics Data System (ADS)

Hu, Chuanmin; Lee, Zhongping; Muller-Karger, Frank E.; Carder, Kendall L.

2003-05-01

A spectra-matching optimization algorithm, designed for hyperspectral sensors, has been implemented to process SeaWiFS-derived multi-spectral water-leaving radiance data. The algorithm has been tested over Southwest Florida coastal waters. The total spectral absorption and backscattering coefficients can be well partitioned with the inversion algorithm, resulting in RMS errors generally less than 5% in the modeled spectra. For extremely turbid waters that come from either river runoff or sediment resuspension, the RMS error is in the range of 5-15%. The bio-optical parameters derived in this optically complex environment agree well with those obtained in situ. Further, the ability to separate backscattering (a proxy for turbidity) from the satellite signal makes it possible to trace water movement patterns, as indicated by the total absorption imagery. The derived patterns agree with those from concurrent surface drifters. For waters where CDOM overwhelmingly dominates the optical signal, however, the procedure tends to regard CDOM as the sole source of absorption, implying the need for better atmospheric correction and for adjustment of some model coefficients for this particular region.

Teaching the Balanced Scorecard through Simulation

ERIC Educational Resources Information Center

Capelo, Carlos; Lopes, Ana Isabel; Mata, Ana

2012-01-01

Kaplan and Norton introduced the Balanced Scorecard (BSC) which is based on a systems perspective of the business strategy and performance measurement. Many organizations around the world are using the BSC to define, implement and manage strategy. Nevertheless there exist studies that identify problems and limitations associated with the…

Biological soil crust as a bio-mediator alters hydrological processes in stabilized dune system of the Tengger Desert, China

NASA Astrophysics Data System (ADS)

Li, Xinrong

2016-04-01

Biological soil crust (BSC) is a vital component in the stabilized sand dunes with a living cover up to more than 70% of the total, which has been considered as a bio-mediator that directly influences and regulates the sand dune ecosystem processes. However, its influences on soil hydrological processes have been long neglected in Chinese deserts. In this study, BSCs of different successional stages were chose to test their influence on the hydrological processes of stabilized dune, where the groundwater deep exceeds 30m, further to explore why occur the sand-binding vegetation replacement between shrubs and herbs. Our long-term observation (60 years) shows that cyanobacteria crust has been colonized and developed after 3 years since the sand-binding vegetation has been established and dune fixation using planted xerophytic shrubs and made sand barrier (straw-checkerboard) on shifting dune surface, lichen and moss crust occurred after 20 years, and the cover of moss dominated crust could reach 70 % after 50 years. The colonization and development of BSC altered the initial soil water balance of revegetated areas by influencing rainfall infiltration, soil evaporation and dew water entrapment. The results show that BSC obviously reduced the infiltration that occurred during most rainfall events (80%), when rainfall was greater than 5 mm or less than 20 mm. The presence of BSC reduced evaporation of topsoil after small rainfall (<5 mm) because its high proportion of finer particles slowed the evaporation rate, thus keeping the water in the soil surface longer, and crust facilitated topsoil evaporation when rainfall reached 10 mm. The amount of dew entrapment increases with the succession of BSC. Moreover, the effect of the later successional BSC to dew entrapment, rainfall infiltration and evaporation was more obvious than the early successional BSC on stabilized dunes. In general, BSC reduced the amount of rainfall water that reached deeper soil (0.4-3m), which is where the roots of shrubs are primarily distributed. These changes in the soil moisture pattern induced shifting of sand-binding vegetation from initial planted xerophytic shrub communities with higher coverage (35%) to complex communities dominated by shallow-rooted herbaceous species with low shrub coverage (9%). In correspondence with these changes, soil water balance of the initial vegetation systems (mean soil water kept 3.5%) was turned into a new balance of current vegetation (mean soil water maintains 1.5%). Above findings provide an important enlightenment for future desertification control and sand hazards prevention by revegetation.

Islamic value to the modification of BSC model (a case study in evaluating company performance)

NASA Astrophysics Data System (ADS)

Harwati; Permana, Y.

2017-12-01

Halal is the key word for the Muslim community in consuming goods or services. Providing halal products is the main focus for companies with the largest consumers from the Muslim community. Halal is not only from the ingredients but also from the process in its production. The purpose of this study is to design a model of performance measurement for a company in order to provide halal products. Balance Score Card (BSC) is used as a framework. BSC as a performance measurement system has advantages not only focus on financial aspect but also non finance. Islamic values are incorporated into four perspective of BSC. They are: Selection of sharia financial institutions in financial perspective, payment method by consumer in consumer perspective, number of product with halal certificate and menu clarify in internal business process perspective, then accuracy of payroll time in learning and growth perspective. The modified BSC model obtains 17 Key Performance Indicators (KPI). The model is applied in a culinary industry (restaurant). Structured questionnaires and scheduled interviews are used to collect the important data. The result show that these industry fail to meet 8 from total 17 KPI so performance achievement is only 70.81%, and only reach 22.58% in Islamic value aspect. This is recorded by the company as an input to improve their performance in order to compete in halal food business.

The energy-dependent electron loss model: backscattering and application to heterogeneous slab media.

PubMed

Lee, Tae Kyu; Sandison, George A

2003-01-21

Electron backscattering has been incorporated into the energy-dependent electron loss (EL) model and the resulting algorithm is applied to predict dose deposition in slab heterogeneous media. This algorithm utilizes a reflection coefficient from the interface that is computed on the basis of Goudsmit-Saunderson theory and an average energy for the backscattered electrons based on Everhart's theory. Predictions of dose deposition in slab heterogeneous media are compared to the Monte Carlo based dose planning method (DPM) and a numerical discrete ordinates method (DOM). The slab media studied comprised water/Pb, water/Al, water/bone, water/bone/water, and water/lung/water, and incident electron beam energies of 10 MeV and 18 MeV. The predicted dose enhancement due to backscattering is accurate to within 3% of dose maximum even for lead as the backscattering medium. Dose discrepancies at large depths beyond the interface were as high as 5% of dose maximum and we speculate that this error may be attributed to the EL model assuming a Gaussian energy distribution for the electrons at depth. The computational cost is low compared to Monte Carlo simulations making the EL model attractive as a fast dose engine for dose optimization algorithms. The predictive power of the algorithm demonstrates that the small angle scattering restriction on the EL model can be overcome while retaining dose calculation accuracy and requiring only one free variable, chi, in the algorithm to be determined in advance of calculation.

The energy-dependent electron loss model: backscattering and application to heterogeneous slab media

NASA Astrophysics Data System (ADS)

Lee, Tae Kyu; Sandison, George A.

2003-01-01

Electron backscattering has been incorporated into the energy-dependent electron loss (EL) model and the resulting algorithm is applied to predict dose deposition in slab heterogeneous media. This algorithm utilizes a reflection coefficient from the interface that is computed on the basis of Goudsmit-Saunderson theory and an average energy for the backscattered electrons based on Everhart's theory. Predictions of dose deposition in slab heterogeneous media are compared to the Monte Carlo based dose planning method (DPM) and a numerical discrete ordinates method (DOM). The slab media studied comprised water/Pb, water/Al, water/bone, water/bone/water, and water/lung/water, and incident electron beam energies of 10 MeV and 18 MeV. The predicted dose enhancement due to backscattering is accurate to within 3% of dose maximum even for lead as the backscattering medium. Dose discrepancies at large depths beyond the interface were as high as 5% of dose maximum and we speculate that this error may be attributed to the EL model assuming a Gaussian energy distribution for the electrons at depth. The computational cost is low compared to Monte Carlo simulations making the EL model attractive as a fast dose engine for dose optimization algorithms. The predictive power of the algorithm demonstrates that the small angle scattering restriction on the EL model can be overcome while retaining dose calculation accuracy and requiring only one free variable, χ, in the algorithm to be determined in advance of calculation.

Performance evaluation of Al-Zahra academic medical center based on Iran balanced scorecard model.

PubMed

Raeisi, Ahmad Reza; Yarmohammadian, Mohammad Hossein; Bakhsh, Roghayeh Mohammadi; Gangi, Hamid

2012-01-01

Growth and development in any country's national health system, without an efficient evaluation system, lacks the basic concepts and tools necessary for fulfilling the system's goals. The balanced scorecard (BSC) is a technique widely used to measure the performance of an organization. The basic core of the BSC is guided by the organization's vision and strategies, which are the bases for the formation of four perspectives of BSC. The goal of this research is the performance evaluation of Al-Zahra Academic Medical Center in Isfahan University of Medical Sciences, based on Iran BSC model. This is a combination (quantitative-qualitative) research which was done at Al-Zahra Academic Medical Center in Isfahan University of Medical Sciences in 2011. The research populations were hospital managers at different levels. Sampling method was purposive sampling in which the key informed personnel participated in determining the performance indicators of hospital as the BSC team members in focused discussion groups. After determining the conceptual elements in focused discussion groups, the performance objectives (targets) and indicators of hospital were determined and sorted in perspectives by the group discussion participants. Following that, the performance indicators were calculated by the experts according to the predetermined objectives; then, the score of each indicator and the mean score of each perspective were calculated. Research findings included development of the organizational mission, vision, values, objectives, and strategies. The strategies agreed upon by the participants in the focus discussion group included five strategies, which were customer satisfaction, continuous quality improvement, development of human resources, supporting innovation, expansion of services and improving the productivity. Research participants also agreed upon four perspectives for the Al-Zahra hospital BSC. In the patients and community perspective (customer), two objectives and three indicators were agreed upon, with a mean score of 75.9%. In the internal process perspective, 4 objectives and 14 indicators were agreed upon, with a mean score of 79.37%. In the learning and growth perspective, four objectives and eight indicators were agreed upon, with a mean score of 81.11%. Finally, in the financial perspective, two objectives and five indicators were agreed upon, with a mean score of 67.15%. One way to create demand for hospital services is performance evaluation by paying close attention to all BSC perspectives, especially the non-financial perspectives such as customers and internal processes perspectives. In this study, the BSC showed the differences in performance level of the organization in different perspectives, which would assist the hospital managers improve their performance indicators. The learning and growth perspective obtained the highest score, and the financial perspective obtained the least score. Since the learning and growth perspective acts as a base for all other perspectives and they depend on it, hospitals must continuously improve the service processes and the quality of services by educating staff and updating their policies and procedures. This can increase customer satisfaction and productivity and finally improve the BSC in financial perspective.

Aerosol Optical Depth over Europe: Evaluation of the CALIOPE air quality modelling system with direct-sun AERONET observations

NASA Astrophysics Data System (ADS)

Basart, Sara; Pay, María. Teresa; Pérez, Carlos; Cuevas, Emilio; Jorba, Oriol; Piot, Matthias; María Baldasano, Jose

2010-05-01

In the frame of the CALIOPE project (Baldasano et al., 2008), the Barcelona Supercomputing Center (BSC-CNS) currently operates a high-resolution air quality forecasting system based on daily photochemical forecasts in Europe (12km x 12km resolution) with the WRF-ARW/HERMES/CMAQ modelling system (http://www.bsc.es/caliope) and desert dust forecasts over Southern Europe with BSC-DREAM8b (Pérez et al., 2006; http://www.bsc.es/projects/earthscience/DREAM). High resolution simulations and forecasts are possible through their implementation on MareNostrum supercomputer at BSC-CNS. As shown in previous air quality studies (e.g. Rodríguez et al., 2001; Jiménez-Guerrero et al., 2008), the contribution of desert dust on particulate matter levels in Southern Europe is remarkable due to its proximity to African desert dust sources. When considering only anthropogenic emissions (Baldasano et al., 2008) and the current knowledge about aerosol physics and chemistry, chemistry-transport model simulations underestimate the PM10 concentrations by 30-50%. As a first approach, the natural dust contribution from BSC-DREAM8b is on-line added to the anthropogenic aerosol output of CMAQ. The aim of the present work is the quantitative evaluation of the WRF-ARW/HERMES/ CMAQ/BSC-DREAM8b forecast system to simulate the Aerosol Optical Depth (AOD) over Europe. The performance of the modelled AOD has been quantitatively evaluated with discrete and categorical (skill scores) statistics by a comparison to direct-sun AERONET observations for 2004. The contribution of different types of aerosols will be analyzed by means of the O'Neill fine mode AOD products (O'Neill et al., 2001). A previous aerosol characterization of AERONET data was performed (Basart et al., 2009) in order to discriminate the different aerosol source contributions within the study region. The results indicate a remarkable improvement in the discrete and skill-scores evaluation (accuracy, critical success index and probability of detection) of AOD when using CMAQ+DREAM8b compared to CMAQ-alone simulations. An accurate analysis of the relative contributions of anthropogenic aerosols and desert dust to AOD over Europe and their seasonality will be also presented. References: Baldasano J.M, P. Jiménez-Guerrero, O. Jorba, C. Pérez, E. López, P. Güereca, F. Martin, M. García-Vivanco, I. Palomino, X. Querol, M. Pandolfi, M.J. Sanz and J.J. Diéguez: "CALIOPE: An operational air quality forecasting system for the Iberian Peninsula, Balearic Islands and Canary Islands- First annual evaluation and ongoing developments", Adv. Sci. and Res., 2: 89-98, 2008. Baldasano J.M., L. P. Güereca, E. López, S. Gassó, P. Jimenez-Guerrero. "Development of a high resolution (1 km x 1 km, 1 h) emission model for Spain: the High-Elective Resolution Modelling Emission System (HERMES)". Atmospheric Environment, 42: 7215-7233 doi: 10.1016/j.atmosenv.2008.07.026, 2008. Basart, S., Pérez, C., Cuevas, E., Baldasano, J. M. and Gobbi, G. P. "Aerosol characterization in Northern Africa, Northeastern Atlantic, Mediterranean Basin and Middle East from direct-sun AERONET observations", Atmos. Chem. Phys.., 9, 7707-7745, 2009. Jiménez-Guerrero, P., Pérez, C., Jorba, O. and Baldasano, J. M. "Contribution of Saharan dust in an integrated air quality system and its on-line assessment", Geophys. Res. Lett., 35(3), 2008. O'Neill, N. T., Dubovik, O., and Eck, T. F.: A modified Angstrom coefficient for the characterization of sub-micron aerosols, App. Opt., 40(14), 2368-2375, 2001. Pérez, C., Nickovic, S., Pejanovic, G., Baldasano, J. M. and Ozsoy, E. "Interactive dust-radiation modeling: A step to improve weather forecasts", Geophys. Res., 11(D16206),doi:10.1029/2005JD006717, 2006. Rodríguez, S., Querol, X., Alastuey, A., Kallos, G. and Kakaliagou, O. "Saharan dust contributions to PM10 and TSP levels in Southern and Eastern Spain", Atmos. Environ., 35, 2433-2447, 2001.

Implementation and Performance Evaluation Using the Fuzzy Network Balanced Scorecard

ERIC Educational Resources Information Center

Tseng, Ming-Lang

2010-01-01

The balanced scorecard (BSC) is a multi-criteria evaluation concept that highlights the importance of performance measurement. However, although there is an abundance of literature on the BSC framework, there is a scarcity of literature regarding how the framework with dependence and interactive relationships should be properly implemented in…

76 FR 76416 - Board of Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-07

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR) In accordance with..., Office of Public Health Preparedness and Response (OPHPR), concerning strategies and goals for the...

77 FR 20823 - Board of Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-06

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR) In accordance with... Public Health Preparedness and Response (OPHPR), concerning strategies and goals for the programs and...

76 FR 53474 - Board of Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-26

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR) In accordance with... Control and Prevention (CDC), and the Director, Office of Public Health Preparedness and Response (OPHPR...

76 FR 18221 - Board of Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-01

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Public Health Preparedness and Response (BSC, OPHPR) In accordance with... of Public Health Preparedness and Response (OPHPR), concerning strategies and goals for the programs...

78 FR 56235 - Board of Scientific Counselors, Office of Public Health Preparedness and Response, (BSC, OPHPR)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-12

... Scientific Counselors, Office of Public Health Preparedness and Response, (BSC, OPHPR) In accordance with..., Office of Public Health Preparedness and Response (OPHPR), concerning strategies and goals for the... Information: Marquita Black, Office of Science and Public Health Practice, Executive Assistant, Centers for...

78 FR 13678 - Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-28

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID) Notice of Cancellation: A notice was... management activities, for both the Centers for Disease Control and Prevention and the Agency for Toxic...

Identifying Balance in a Balanced Scorecard System

ERIC Educational Resources Information Center

Aravamudhan, Suhanya; Kamalanabhan, T. J.

2007-01-01

In recent years, strategic management concepts seem to be gaining greater attention from the academicians and the practitioner's alike. Balanced Scorecard (BSC) concept is one such management concepts that has spread in worldwide business and consulting communities. The BSC translates mission and vision statements into a comprehensive set of…

Applying the Balanced Scorecard to Education

ERIC Educational Resources Information Center

Karathanos, Demetrius; Karathanos, Patricia

2005-01-01

Although the application of the balanced scorecard (BSC) in the business sector is well documented, very little research has been reported regarding the adaptation or application of the BSC in the education sector. In this article, the authors (a) describe how the Baldrige Education Criteria for Performance Excellence has adapted the concept of…

Recruitment and Retention with a Spin

ERIC Educational Resources Information Center

Lindgren, Rita; Hixson, Carla Braun

2010-01-01

Strategic planning and innovation at Bismarck State College (BSC) found common ground in the college's goal to recruit and retain employees in an environment of low unemployment and strong competition for skilled employees. BSC's strategic plan for 2007-09 included the objective "to increase retention of employees." One of the strategies…

78 FR 11651 - Board of Scientific Counselors, National Institute for Occupational Safety and Health (BSC, NIOSH)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-19

... Scientific Counselors, National Institute for Occupational Safety and Health (BSC, NIOSH) In accordance with..., research, experiments, and demonstrations relating to occupational safety and health and to mine health... Occupational Safety and Health on research and prevention programs. Specifically, the Board shall provide...

77 FR 47850 - Board of Scientific Counselors, National Institute for Occupational Safety and Health (BSC, NIOSH)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-10

... Scientific Counselors, National Institute for Occupational Safety and Health (BSC, NIOSH) In accordance with..., research, experiments, and demonstrations relating to occupational safety and health and to mine health... Occupational Safety and Health on research and prevention programs. Specifically, the Board shall provide...

Characterization of vegetation by microwave and optical remote sensing

NASA Technical Reports Server (NTRS)

Daughtry, C. S. T. (Principal Investigator); Ranson, K. J.; Biehl, L. L.

1986-01-01

Two series of carefully controlled experiments were conducted. First, plots of important crops (corn, soybeans, and sorghum), prairie grasses (big bluestem, switchgrass, tal fescue, orchardgrass, bromegrass), and forage legumes (alfalfa, red clover, and crown vetch) were manipulated to produce wide ranges of phytomass, leaf area index, and canopy architecture. Second, coniferous forest canopies were simulated using small balsam fir trees grown in large pots of soil and arranged systematically on a large (5 m) platform. Rotating the platform produced many new canopies for frequency and spatial averaging of the backscatter signal. In both series of experiments, backscatter of 5.0 GHz (C-Band) was measured as a function of view angle and polarization. Biophysical measurements included leaf area index, fresh and dry phytomass, water content of canopy elements, canopy height, and soil roughness and moisture content. For a subset of the above plots, additional measurements were acquired to exercise microwave backscatter models. These measurements included size and shape of leaves, stems, and fruit and the probability density function of leaf and stem angles. The relationships of the backscattering coefficients and the biophysical properties of the canopies were evaluated using statistical correlations, analysis of variance, and regression analysis. Results from the corn density and balsam fir experiments are discussed and analyses of data from the other experiments are summarized.

A Model for Backscattering from Quasi Periodic Corn Canopies at L-Band

NASA Technical Reports Server (NTRS)

Lang, R.; Utku, C.; Zhao, Q.; O'Neill, P.

2010-01-01

In this study, a model for backscattering at L-band from a corn canopy is proposed. The canopy consists of a quasi-periodic distribution of stalks and a random distribution of leaves. The Distorted Born Approximation (DBA) is employed to calculate the single scattered return from the corn field. The new feature of the method is that the coherence of the stalks in the row direction is incorporated in the model in a systematic fashion. Since the wavelength is on the order of the distance between corn stalks in a row, grating lobe behavior is observed at certain azimuth angles of incidence. The results are compared with experimental values measured in Huntsville, Alabama in 1998. The mean field and the effective dielectric constant of the canopy are obtained by using the Foldy approximation. The stalks are placed in the effective medium in a two dimensional lattice to simulate the row structure of a corn field. In order to mimic a real corn field, a quasi-periodic stalk distribution is assumed where the stalks are given small random perturbations about their lattice locations. Corn leaves are also embedded in the effective medium and the backscattered field from the stalks and the leaves is computed. The backscattering coefficient is calculated and averaged over successive stalk position perturbations. It is assumed that soil erosion has smoothed the soil sufficiently so that it can be assumed flat. Corn field backscatter data was collected from cornfields during the Huntsville 98 experimental campaign held at Alabama A&M University Research Station, Huntsville, Alabama in 1998 using the NASA/GW truck mounted radar. Extensive ground truth data was collected. This included soil moisture measurements and corn plant architectural data to be used in the model. In particular, the distances between the stalks in a single row have been measured. The L-band radar backscatter data was collected for both H and V polarizations and for look angles of 15o and 45o over a two week period under varying soil moisture conditions. These measured backscattering values will be compared with the model backscattering values and a discussion of the results will be presented.

Progress in radar snow research. [Brookings, South Dakota

NASA Technical Reports Server (NTRS)

Stiles, W. H.; Ulaby, F. T.; Fung, A. K.; Aslam, A.

1981-01-01

Multifrequency measurements of the radar backscatter from snow-covered terrain were made at several sites in Brookings, South Dakota, during the month of March of 1979. The data are used to examine the response of the scattering coefficient to the following parameters: (1) snow surface roughness, (2) snow liquid water content, and (3) snow water equivalent. The results indicate that the scattering coefficient is insensitive to snow surface roughness if the snow is drv. For wet snow, however, surface roughness can have a strong influence on the magnitude of the scattering coefficient. These observations confirm the results predicted by a theoretical model that describes the snow as a volume of Rayleig scatterers, bounded by a Gaussian random surface. In addition, empirical models were developed to relate the scattering coefficient to snow liquid water content and the dependence of the scattering coefficient on water equivalent was evaluated for both wet and dry snow conditions.

Enhancement effects in polarimetric radar returns: Phase difference statistics

NASA Technical Reports Server (NTRS)

Lang, R. H.; Khadr, N.

1993-01-01

The probability density functions (pdfs) of the co- and cross-polarized phase differences are derived for backscatter from vegetation using the coherent and incoherent scattering theories. Unlike previous derivations, no assumptions or observations other than the applicability of the Central Limit Theorem (CLT), the low fractional volume of the medium, the reciprocity of the scatterers, and the azimuthal symmetry of the scatterer's orientation statistics are employed. Everything else follows logically via the mathematics. The difference between the coherent theory and the incoherent theory is referred to as the backscatter enhancement effect. The influence of this enhancement effect on the phase difference pdfs is examined and found to be important under combined conditions of scatterer anisotropy and appropriate reflection coefficient values.

Lidar measurements of stratospheric aerosols over Menlo Park, California, October 1972 - March 1974

NASA Technical Reports Server (NTRS)

Russell, P. B.; Viezee, W.; Hake, R. D.

1974-01-01

During an 18-month period, 30 nighttime observations of stratospheric aerosols were made using a ground based ruby lidar located near the Pacific coast of central California (37.5 deg. N, 122.2 deg. W). Vertical profiles of the lidar scattering ratio and the particulate backscattering coefficient were obtained by reference to a layer of assumed negligible particulate content. An aerosol layer centered near 21 km was clearly evident in all observations, but its magnitude and vertical distribution varied considerably throughout the observation period. A reduction of particulate backscattering in the 23- to 30-km layer during late January 1973 appears to have been associated with the sudden stratospheric warming which occurred at that time.

Scattering from randomly oriented circular discs with application to vegetation

NASA Technical Reports Server (NTRS)

Karam, M. A.; Fung, A. K.

1984-01-01

A vegetation layer is modeled by a collection of randomly oriented circular discs over a half space. The backscattering coefficient from such a half space is computed using the radiative transfer theory. It is shown that significantly different results are obtained from this theory as compared with some earlier investigations using the same modeling approach but with restricted disc orientations. In particular, the backscattered cross polarized returns cannot have a fast increasing angular trend which is inconsistent with measurements. By setting the appropriate angle of orientation to zero the theory reduces to previously published results. Comparisons are shown with measurements taken from milo, corn and wheat and good agreements are obtained for both polarized and cross polarized returns.

Scattering from randomly oriented circular discs with application to vegetation

NASA Technical Reports Server (NTRS)

Karam, M. A.; Fung, A. K.

1983-01-01

A vegetation layer is modeled by a collection of randomly oriented circular discs over a half space. The backscattering coefficient from such a half space is computed using the radiative transfer theory. It is shown that significantly different results are obtained from this theory as compared with some earlier investigations using the same modeling approach but with restricted disc orientations. In particular, the backscattered cross-polarized returns cannot have a fast increasing angular trend which is inconsistent with measurements. By setting the appropriate angle of orientation to zero the theory reduces to previously published results. Comparisons are shown with measurements taken from milo, corn and wheat and good agreements are obtained for both polarized and cross-polarized returns.

Ratify, Reject or Revise: Balanced Scorecard and Universities

ERIC Educational Resources Information Center

Sayed, Naqi

2013-01-01

Purpose: The purpose of this paper is to examine the use of the Balanced Scorecard (BSC) in universities. Initially directed toward profit-oriented businesses, the BSC has since been adopted by many non-profit organisations with seemingly diverse objectives. A number of primarily publicly-funded universities and institutions, which are part of…

78 FR 21370 - Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-10

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID) In accordance with section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC...

75 FR 69687 - Board of Scientific Counselors, Office of Infectious Diseases, (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-15

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases, (BSC, OID) In accordance with section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC...

78 FR 11651 - Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-19

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID) In accordance with section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC...

78 FR 69683 - Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-20

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID) In accordance with section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC...

78 FR 17411 - Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-21

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID) In accordance with section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC...

76 FR 24031 - Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-29

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID) In accordance with section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC...

76 FR 63926 - Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-14

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID) In accordance with section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC...

77 FR 21778 - Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-11

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID) In accordance with section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC...

75 FR 66772 - Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID)

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-29

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, Office of Infectious Diseases (BSC, OID) In accordance with section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC...

75 FR 55333 - Board of Scientific Counselors, National Center for Health Statistics, (BSC, NCHS)

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-10

... Scientific Counselors, National Center for Health Statistics, (BSC, NCHS) In accordance with section 10(a)(2... Prevention (CDC), National Center for Health Statistics (NCHS) announces the following meeting of [email protected] or Virginia Cain, [email protected] at least 10 days in advance for requirements). All visitors...

76 FR 36923 - Meeting of the National Toxicology Program (NTP) Board of Scientific Counselors (BSC): Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-23

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Meeting of the National Toxicology Program (NTP) Board of Scientific Counselors (BSC): Notice of Cancellation AGENCY: National Toxicology Program (NTP), National... Toxicology Program. [FR Doc. 2011-15656 Filed 6-22-11; 8:45 am] BILLING CODE 4140-01-P ...

A Simulation-Based Approach for Teaching the Systems Perspective of Strategic Performance Management

ERIC Educational Resources Information Center

Capelo, Carlos; Lopes, Ana; Mata, Ana

2015-01-01

Kaplan and Norton introduced the balanced scorecard (BSC), which is based on a systems perspective of the business strategy and performance measurement. Many organisations around the world use the BSC to define, implement and manage strategy. Nevertheless, there are studies that identify problems and limitations associated with the implementation…

75 FR 42448 - Board of Scientific Counselors (BSC), Coordinating Center for Health Promotion (CCHP): Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-21

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention (CDC) Board of Scientific Counselors (BSC), Coordinating Center for Health Promotion (CCHP): Notice of Charter Amendment... both the CDC and the Agency for Toxic Substances and Disease Registry. Dated: July 13, 2010. Elaine L...

[Management and accounting solution required in clinical laboratory department in the hospital and the balanced scorecard (BSC)].

PubMed

Takahashi, Toshiro

2006-11-01

This is to describe required accounting knowledge and the techniques for the clinical laboratory department management level people to operate their division from the viewpoint of management. Especially, the necessity and the efficacy of the BSC implementation in the clinical laboratory department are being explained.

78 FR 51729 - Board of Scientific Counselors, National Institute for Occupational Safety and Health (BSC, NIOSH)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-21

... Scientific Counselors, National Institute for Occupational Safety and Health (BSC, NIOSH) In accordance with... demonstrations relating to occupational safety and health and to mine health. The Board of Scientific Counselors shall provide guidance to the Director, National Institute for Occupational Safety and Health on...

[Development of nursing key performance indicators for an intensive care unit by using a balanced scorecard].

PubMed

Choi, Yun Jeong; Lim, Ji Young; Lee, Young Whee; Kim, Hwa Soon

2008-10-01

The purpose of this study was to develop visions of nursing service, nursing strategies and key performance indicators (KPIs) for an intensive care unit (ICU) based on a Balanced Scorecard (BSC). This study was undertaken by using methodological research. The development process consisted of four phases; the first phase was to develop the vision of nursing in ICUs. The second phase was to develop strategies according to 4 perspectives of a BSC. The third phase was to develop KPIs according to the 4 perspectives of BSC and the final phase was to combine the nursing visions, strategies and KPIs of ICUs. Two main visions of nursing service for ICUs were established. These were 'realization of harmonized professional nursing with human respect' and 'recovery of health through specialized nursing' respectively. In order to reach the aim of developing nursing visions, thirteen practical strategies and nineteen KPIs were developed by four perspectives of the BSC. The results will be used as objective fundamental data to attain business outcomes for the achievement of nursing visions and strategies of ICUs.

A novel hybrid MCDM model for performance evaluation of research and technology organizations based on BSC approach.

PubMed

Varmazyar, Mohsen; Dehghanbaghi, Maryam; Afkhami, Mehdi

2016-10-01

Balanced Scorecard (BSC) is a strategic evaluation tool using both financial and non-financial indicators to determine the business performance of organizations or companies. In this paper, a new integrated approach based on the Balanced Scorecard (BSC) and multi-criteria decision making (MCDM) methods are proposed to evaluate the performance of research centers of research and technology organization (RTO) in Iran. Decision-Making Trial and Evaluation Laboratory (DEMATEL) are employed to reflect the interdependencies among BSC perspectives. Then, Analytic Network Process (ANP) is utilized to weight the indices influencing the considered problem. In the next step, we apply four MCDM methods including Additive Ratio Assessment (ARAS), Complex Proportional Assessment (COPRAS), Multi-Objective Optimization by Ratio Analysis (MOORA), and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) for ranking of alternatives. Finally, the utility interval technique is applied to combine the ranking results of MCDM methods. Weighted utility intervals are computed by constructing a correlation matrix between the ranking methods. A real case is presented to show the efficacy of the proposed approach. Copyright © 2016 Elsevier Ltd. All rights reserved.

Improved identification of the solution space of aerosol microphysical properties derived from the inversion of profiles of lidar optical data, part 1: theory.

PubMed

Kolgotin, Alexei; Müller, Detlef; Chemyakin, Eduard; Romanov, Anton

2016-12-01

Multiwavelength Raman/high spectral resolution lidars that measure backscatter coefficients at 355, 532, and 1064 nm and extinction coefficients at 355 and 532 nm can be used for the retrieval of particle microphysical parameters, such as effective and mean radius, number, surface-area and volume concentrations, and complex refractive index, from inversion algorithms. In this study, we carry out a correlation analysis in order to investigate the degree of dependence that may exist between the optical data taken with lidar and the underlying microphysical parameters. We also investigate if the correlation properties identified in our study can be used as a priori or a posteriori constraints for our inversion scheme so that the inversion results can be improved. We made the simplifying assumption of error-free optical data in order to find out what correlations exist in the best case situation. Clearly, for practical applications, erroneous data need to be considered too. On the basis of simulations with synthetic optical data, we find the following results, which hold true for arbitrary particle size distributions, i.e., regardless of the modality or the shape of the size distribution function: surface-area concentrations and extinction coefficients are linearly correlated with a correlation coefficient above 0.99. We also find a correlation coefficient above 0.99 for the extinction coefficient versus (1) the ratio of the volume concentration to effective radius and (2) the product of the number concentration times the sum of the squares of the mean radius and standard deviation of the investigated particle size distributions. Besides that, we find that for particles of any mode fraction of the particle size distribution, the complex refractive index is uniquely defined by extinction- and backscatter-related Ångström exponents, lidar ratios at two wavelengths, and an effective radius.

Backscatter factors and mass energy-absorption coefficient ratios for diagnostic radiology dosimetry

NASA Astrophysics Data System (ADS)

Benmakhlouf, Hamza; Bouchard, Hugo; Fransson, Annette; Andreo, Pedro

2011-11-01

Backscatter factors, B, and mass energy-absorption coefficient ratios, (μen/ρ)w, air, for the determination of the surface dose in diagnostic radiology were calculated using Monte Carlo simulations. The main purpose was to extend the range of available data to qualities used in modern x-ray techniques, particularly for interventional radiology. A comprehensive database for mono-energetic photons between 4 and 150 keV and different field sizes was created for a 15 cm thick water phantom. Backscattered spectra were calculated with the PENELOPE Monte Carlo system, scoring track-length fluence differential in energy with negligible statistical uncertainty; using the Monte Carlo computed spectra, B factors and (μen/ρ)w, air were then calculated numerically for each energy. Weighted averaging procedures were subsequently used to convolve incident clinical spectra with mono-energetic data. The method was benchmarked against full Monte Carlo calculations of incident clinical spectra obtaining differences within 0.3-0.6%. The technique used enables the calculation of B and (μen/ρ)w, air for any incident spectrum without further time-consuming Monte Carlo simulations. The adequacy of the extended dosimetry data to a broader range of clinical qualities than those currently available, while keeping consistency with existing data, was confirmed through detailed comparisons. Mono-energetic and spectra-averaged values were compared with published data, including those in ICRU Report 74 and IAEA TRS-457, finding average differences of 0.6%. Results are provided in comprehensive tables appropriated for clinical use. Additional qualities can easily be calculated using a designed GUI interface in conjunction with software to generate incident photon spectra.

Quantitative retrieval of aerosol optical properties by means of ceilometers

NASA Astrophysics Data System (ADS)

Wiegner, Matthias; Gasteiger, Josef; Geiß, Alexander

2016-04-01

In the last few years extended networks of ceilometers have been established by several national weather services. Based on improvements of the hardware performance of these single-wavelength backscatter lidars and their 24/7 availability they are increasingly used to monitor mixing layer heights and to derive profiles of the particle backscatter profile. As a consequence they are used for a wide range of applications including the dispersion of volcanic ash plumes, validation of chemistry transport models and air quality studies. In this context the development of automated schemes to detect aerosol layers and to identify the mixing layer are essential, in particular as the latter is often used as a proxy for air quality. Of equal importance is the calibration of ceilometer signals as a pre-requisite to derive quantitative optical properties. Recently, it has been emphasized that the majority of ceilometers are influenced by water vapor absorption as they operate in the spectral range of 905 - 910 nm. If this effect is ignored, errors of the aerosol backscatter coefficient can be as large as 50%, depending on the atmospheric water vapor content and the emitted wavelength spectrum. As a consequence, any other derived quantity, e.g. the extinction coefficient or mass concentration, would suffer from a significant uncertainty in addition to the inherent errors of the inversion of the lidar equation itself. This can be crucial when ceilometer derived profiles shall be used to validate transport models. In this presentation, the methodology proposed by Wiegner and Gasteiger (2015) to correct for water vapor absorption is introduced and discussed.

Role of G protein-coupled estrogen receptor-1, matrix metalloproteinases 2 and 9, and heparin binding epidermal growth factor-like growth factor in estradiol-17β-stimulated bovine satellite cell proliferation.

PubMed

Kamanga-Sollo, E; Thornton, K J; White, M E; Dayton, W R

2014-10-01

In feedlot steers, estradiol-17β (E2) and combined E2 and trenbolone acetate (a testosterone analog) implants enhance rate and efficiency of muscle growth; and, consequently, these compounds are widely used as growth promoters. Although the positive effects of E2 on rate and efficiency of bovine muscle growth are well established, the mechanisms involved in these effects are not well understood. Combined E2 and trenbolone acetate implants result in significantly increased muscle satellite cell number in feedlot steers. Additionally, E2 treatment stimulates proliferation of cultured bovine satellite cells (BSC). Studies in nonmuscle cells have shown that binding of E2 to G protein-coupled estrogen receptor (GPER)-1 results in activation of matrix metalloproteinases 2 and 9 (MMP2/9) resulting in proteolytic release of heparin binding epidermal growth factor-like growth factor (hbEGF) from the cell surface. Released hbEGF binds to and activates the epidermal growth factor receptor resulting in increased proliferation. To assess if GPER-1, MMP2/9, and/or hbEGF are involved in the mechanism of E2-stimulated BSC proliferation, we have examined the effects of G36 (a specific inhibitor of GPER-1), CRM197 (a specific inhibitor of hbEGF), and MMP-2/MMP-9 Inhibitor II (an inhibitor of MMP2/9 activity) on E2-stimulated BSC proliferation. Inhibition of GPER-1, MMP2/9, or hbEGF suppresses E2-stimulated BSC proliferation (P < 0.001) suggesting that all these are required in order for E2 to stimulate BSC proliferation. These results strongly suggest that E2 may stimulate BSC proliferation by binding to GPER-1 resulting in MMP2/9-catalyzed release of cell membrane-bound hbEGF and subsequent activation of epidermal growth factor receptor by binding of released hbEGF. Copyright © 2014 Elsevier Inc. All rights reserved.

Role of G protein-coupled estrogen receptor-1 in estradiol 17β-induced alterations in protein synthesis and protein degradation rates in fused bovine satellite cell cultures.

PubMed

Kamanga-Sollo, E; Thornton, K J; White, M E; Dayton, W R

2017-01-01

In feedlot steers, estradiol-17β (E2) and combined E2 and trenbolone acetate (a testosterone analog) implants enhance rate and efficiency of muscle growth; and, consequently, these compounds are widely used as growth promoters in several countries. Treatment with E2 stimulates protein synthesis rate and suppresses protein degradation rate in fused bovine satellite cell (BSC) cultures; however, the mechanisms involved in these effects are not known with certainty. Although the genomic effects of E2 mediated through the classical estrogen receptors have been characterized, recent studies indicate that binding of E2 to the G protein-coupled estrogen receptor (GPER)-1 mediates nongenomic effects of E2 on cellular function. Our current data show that inhibition of GPER-1, matrix metalloproteinases 2 and 9 (MMP2/9), or heparin binding epidermal growth factor-like growth factor (hbEGF) suppresses E2 stimulate protein synthesis rate in cultured BSCs (P < 0.001) suggesting that all of these are required in order for E2 to stimulate protein synthesis in these cultures. In contrast, inhibition of GPER-1, MMP2/9, or hbEGF has no effect on the ability of E2 to suppress protein degradation rates in fused BSC cultures indicating that these factors are not required in order for E2 to suppress protein degradation rate in these cells. Furthermore, treatment of fused BSC cultures with E2 increased (P < 0.05) pAKT levels indicating that the pAKT pathway may play a role in E2-stimulated effects on cultured BSC. In summary, our current data show that active GPER-1, MMP2/9, and hbEGF are necessary for E2-stimulated protein synthesis but not for E2-simulated suppression of protein degradation in cultured BSC. In addition, E2 treatment increases pAKT levels in cultured BSC. Copyright © 2016 Elsevier Inc. All rights reserved.

The balanced scorecard framework-a case study of patient and employee satisfaction: what happens when it does not work as planned?

PubMed

Lorden, Andrea; Coustasse, Alberto; Singh, Karan P

2008-01-01

The successful utilization of the balanced scorecard (BSC) framework in health care has been demonstrated in the literature. Given these successes, a financially struggling hospital implemented a BSC framework intervention which attempted a culture change centered upon patient satisfaction which it hoped would translate to improved financial stability. Despite the evidence of BSC successes, the intervention, entitled Route 99, did not succeed in this hospital. This case study was conducted to identify learnable lessons and confounding factors associated with the successes and failures of Route 99. Metrics for patient satisfaction and employee satisfaction were examined as reflections of the intervention, the BSC framework, and the confounding financial condition of the hospital. Through case study methodology, mean quarterly patient satisfaction scores tabulated by an outside vendor for inpatient and outpatient services were divided into four time intervals and compared through analysis of variance. Employee satisfaction was measured through a hospital-provided 12-question employee survey, administered through convenience sampling at the beginning and 7 months into Route 99. Each question utilized a 5-point Likert scale and generated two samples which were verified for sample independence through chi-square analysis. Mann-Whitney U test was used for comparison. Inpatient patient satisfaction scores exhibited a nonsignificant upward trend. However, the analysis of variance demonstrated a significant rise in outpatient patient satisfaction (p < .05). An interesting finding was that employee satisfaction declined (p < .05) significantly for supervisors and directors in three areas. The inverse relationship between patient satisfaction and employee satisfaction is in contrast to that found in the literature by the authors. Examination of the BSC framework, the hospital's financial standing, and the metrics for patient satisfaction and employee satisfaction illuminated the importance of management transparency, leadership support, appropriate metric selection, and the strength of the BSC under turbulent circumstances.

Experimental investigation of the early interaction between cyanobacterial soil crusts and vascular plants

NASA Astrophysics Data System (ADS)

Klemens Zaplata, Markus; Veste, Maik; Pohle, Ina; Schümberg, Sabine; Abreu Schonert, Iballa; Hinz, Christoph

2016-04-01

While there are hints that biological soil crusts (BSCs) can constitute physical barriers for the emergence of vascular plants, a conceptual approach for the quantitative evaluation of these effects is still missing. Here we present an experimental design to test the emergence of seedlings in situ with (i) capping natural intact, (ii) destroyed and (iii) removed BSC. The selected field site is directly adjacent to the constructed Hühnerwasser catchment (Lusatia, Germany). This site exists since the end of 2008 and consists of loamy sand. Serving as proxy for seedling thrust, we inserted pre-germinated seeds of three confamiliar plant species with different seed masses (members of the Fabaceae family: Lotus corniculatus L., Ornithopus sativus Brot., and Glycine max (L.) Merr.). In each treatment as well as in the control group planting depths were 10 mm. We took care that experimental plots had identical crust thickness, slightly less than 4 mm, serving as proxy for mechanical resistance. A plot became established as follows: Firstly, the pristine crusted surface was vertically cut. To the windward side the BSC remained intact (i: "with BSC" stripe). To the downwind side soil material was temporarily excavated for laterally inserting the seeds beneath the surface of the first stripe. Then at the thereby disturbed second stripe pulverised BSC material became filled as a top layer (ii: "BSC mix" stripe). From the next stripe the BSC was removed (iii: "no BSC" stripe). Thus each plot had each experimental group in spatial contiguity (within 50 cm × 50 cm). The overall 50 plots were distributed across an area of 40 m × 12 m. When individuals of a species either emerged at all stripes, "× × ×", or at no stripe of a plot, "- - -", there was no reason to suppose any effect of a crust. The "- × ×" emergence pattern (depicting the appearance of seedlings in both stripes possessing manipulated surfaces) points towards hindrance more clearly than "- × -" or "- - ×". Altogether eight possible combinations exist. Combinatorial analysis turned out that seedling emergence had been notably impeded for light-weighted seeds but little for heavy seeds. Repeated recordings enable to account for adaptable emergence of seedlings according to varying crust conditions - in spatial as well as temporal terms. The proposed experimental procedure hence is highly recommended as a viable instrument to further investigate filter and facilitation processes between BSCs and vascular plants.

Petrology of the Basalt of Summit Creek: A [Slab] Window into Pacific Northwest Tectonics during the Eocene

NASA Astrophysics Data System (ADS)

Kant, L. B.; Tepper, J. H.; Nelson, B. K.

2012-12-01

Variation in composition of basalts within the Cascade arc reflects the regional effects of subducting slab windows. The earliest preserved Tertiary manifestation of this process is the 55-44 Ma Basalt of Summit Creek (BSC), located southeast of Mount Rainier. At the base of this steeply dipping 2000 m section of subaerial lavas are basalts / diabases with arc traits (e.g., HFSE depletions, 1.0-1.2 wt. % K2O) and isotopic compositions (207Pb/204Pb > 15.58; ɛNd = +5.8 to +6.7) that overlap those of modern Cascade arc rocks. Conformably overlying these arc rocks (and separated by ~35m of shale, sandstone and conglomerate) are tholeiitic basalts with OIB affinities (<0.4 wt. % K2O, Y/Nb = 1.1-2.3, concave spidergram profiles) and isotopic signatures of a more depleted mantle source (207Pb/204Pb < 15.56; ɛNd = +7.1 to +7.8). In major element, trace element, and isotopic composition the upper BSC lavas are broadly similar to the voluminous Crescent Formation basalts on the Olympic Peninsula, which are coeval with the BSC but located ~100 km farther west. Compositional diversity within the upper BSC section (Mg# 66-30) appears to reflect both fractional crystallization and source heterogeneity. Modeling with MELTS (Ghiroso and Sack, 1995) indicates that differentiation dominated by removal of clinopyroxene and plagioclase took place at mid crustal depths (P = 5 kbar) and that the parent magma had <0.2 wt. % water. However, this process cannot account for all incompatible element data, which indicate the existence of two distinct magma series that differ most notably in Sr, Zr, and K2O contents. Arc basalts of the lower BSC may represent the southernmost extension of the Cretaceous-Tertiary North Cascades arc (Miller et al., 2009); however, basalts higher in the section have OIB traits and reflect a different tectonic setting. We propose that the transition from arc to OIB magmatism in the BSC records the arrival beneath the arc of a slab window produced by subduction of the Kula-Farallon Ridge (KFR). Previous research on subduction of the KFR has been limited to the coast. Improved dating and petrology of the BSC will help to better constrain the location and behavior of the KFR slab window as it moved further inboard beneath the North American plate.

Performance evaluation of Al-Zahra academic medical center based on Iran balanced scorecard model

PubMed Central

Raeisi, Ahmad Reza; Yarmohammadian, Mohammad Hossein; Bakhsh, Roghayeh Mohammadi; Gangi, Hamid

2012-01-01

Background: Growth and development in any country's national health system, without an efficient evaluation system, lacks the basic concepts and tools necessary for fulfilling the system's goals. The balanced scorecard (BSC) is a technique widely used to measure the performance of an organization. The basic core of the BSC is guided by the organization's vision and strategies, which are the bases for the formation of four perspectives of BSC. The goal of this research is the performance evaluation of Al-Zahra Academic Medical Center in Isfahan University of Medical Sciences, based on Iran BSC model. Materials and Methods: This is a combination (quantitative–qualitative) research which was done at Al-Zahra Academic Medical Center in Isfahan University of Medical Sciences in 2011. The research populations were hospital managers at different levels. Sampling method was purposive sampling in which the key informed personnel participated in determining the performance indicators of hospital as the BSC team members in focused discussion groups. After determining the conceptual elements in focused discussion groups, the performance objectives (targets) and indicators of hospital were determined and sorted in perspectives by the group discussion participants. Following that, the performance indicators were calculated by the experts according to the predetermined objectives; then, the score of each indicator and the mean score of each perspective were calculated. Results: Research findings included development of the organizational mission, vision, values, objectives, and strategies. The strategies agreed upon by the participants in the focus discussion group included five strategies, which were customer satisfaction, continuous quality improvement, development of human resources, supporting innovation, expansion of services and improving the productivity. Research participants also agreed upon four perspectives for the Al-Zahra hospital BSC. In the patients and community perspective (customer), two objectives and three indicators were agreed upon, with a mean score of 75.9%. In the internal process perspective, 4 objectives and 14 indicators were agreed upon, with a mean score of 79.37%. In the learning and growth perspective, four objectives and eight indicators were agreed upon, with a mean score of 81.11%. Finally, in the financial perspective, two objectives and five indicators were agreed upon, with a mean score of 67.15%. Conclusion: One way to create demand for hospital services is performance evaluation by paying close attention to all BSC perspectives, especially the non-financial perspectives such as customers and internal processes perspectives. In this study, the BSC showed the differences in performance level of the organization in different perspectives, which would assist the hospital managers improve their performance indicators. The learning and growth perspective obtained the highest score, and the financial perspective obtained the least score. Since the learning and growth perspective acts as a base for all other perspectives and they depend on it, hospitals must continuously improve the service processes and the quality of services by educating staff and updating their policies and procedures. This can increase customer satisfaction and productivity and finally improve the BSC in financial perspective. PMID:23555104

Cost Effectiveness Analysis of Different Management Strategies between Best Supportive Care and Second-line Chemotherapy for Platinum-resistant or Refractory Ovarian Cancer.

PubMed

Luealon, Phanida; Khempech, Nipon; Vasuratna, Apichai; Hanvoravongchai, Piya; Havanond, Piyalamporn

2016-01-01

There is no standard treatment for patients with platinum-resistant or refractory epithelial ovarian cancer. Single agent chemotherapies have evidence of more efficacy and less toxicity than combination therapy. Most are very expensive, with appreciable toxicity and minimal survival. Since it is difficult to make comparison between outcomes, economic analysis of single-agent chemotherapy regimens and best supportive care may help to make decisions about an appropriate management for the affected patients. To evaluate the cost effectiveness of second-line chemotherapy compared with best supportive care for patients with platinum-resistant or refractory epithelial ovarian cancer. A Markov model was used to estimate the effectiveness and total costs associated with treatments. The hypothetical patient population comprised women aged 55 with platinum-resistant or refractory epithelial ovarian cancer. Four types of alternative treatment options were evaluated: 1) gemcitabine followed by BSC; 2) pegylated liposomal doxorubicin (PLD) followed by BSC; 3) gemcitabine followed by topotecan; and 4) PLD followed by topotecan. Baseline comparator of alternative treatments was BSC. Time horizon of the analysis was 2 years. Health care provider perspective and 3% discount rate were used to determine the costs of medical treatment in this study. Quality-adjusted life-years (QALY) were used to measure the treatment effectiveness. Treatment effectiveness data were derived from the literature. Costs were calculated from unit cost treatment of epithelial ovarian cancer patients at various stages of disease in King Chulalongkorn Memorial Hospital (KCMH) in the year 2011. Parameter uncertainty was tested in probabilistic sensitivity analysis by using Monte Carlo simulation. One-way sensitivity analysis was used to explore each variable's impact on the uncertainty of the results. Approximated life expectancy of best supportive care was 0.182 years and its total cost was 26,862 Baht. All four alternative treatments increased life expectancy. Life expectancy of gemcitabine followed by BSC, PLD followed by BSC, gemcitabine followed by topotecan and PLD followed by topotecan was 0.510, 0.513, 0.566, and 0.570 years, respectively. The total cost of gemcitabine followed by BSC, PLD followed by BSC, gemcitabine followed by topotecan and PLD followed by topotecan was 113,000, 124,302, 139,788 and 151,135 Baht, respectively. PLD followed by topotecan had the highest expected quality-adjusted life-years but was the most expensive of all the above strategies. The incremental cost-effectiveness ratios (ICER) of gemcitabine followed by BSC, PLD followed by BSC, gemcitabine followed by topotecan and PLD followed by topotecan was 344,643, 385,322, 385,856, and 420,299 Baht, respectively. All of the second-line chemotherapy strategies showed certain benefits due to an increased life- year gained compared with best supportive care. Moreover, gemcitabine as second-line chemotherapy followed by best supportive care in progressive disease case was likely to be more effective strategy with less cost from health care provider perspective. Gemcitabine was the most cost-effective treatment among all four alternative treatments. ICER is only an economic factor. Treatment decisions should be based on the patient benefit.

Coherent backscattering of light by complex random media of spherical scatterers: numerical solution

NASA Astrophysics Data System (ADS)

Muinonen, Karri

2004-07-01

Novel Monte Carlo techniques are described for the computation of reflection coefficient matrices for multiple scattering of light in plane-parallel random media of spherical scatterers. The present multiple scattering theory is composed of coherent backscattering and radiative transfer. In the radiative transfer part, the Stokes parameters of light escaping from the medium are updated at each scattering process in predefined angles of emergence. The scattering directions at each process are randomized using probability densities for the polar and azimuthal scattering angles: the former angle is generated using the single-scattering phase function, whereafter the latter follows from Kepler's equation. For spherical scatterers in the Rayleigh regime, randomization proceeds semi-analytically whereas, beyond that regime, cubic spline presentation of the scattering matrix is used for numerical computations. In the coherent backscattering part, the reciprocity of electromagnetic waves in the backscattering direction allows the renormalization of the reversely propagating waves, whereafter the scattering characteristics are computed in other directions. High orders of scattering (~10 000) can be treated because of the peculiar polarization characteristics of the reverse wave: after a number of scatterings, the polarization state of the reverse wave becomes independent of that of the incident wave, that is, it becomes fully dictated by the scatterings at the end of the reverse path. The coherent backscattering part depends on the single-scattering albedo in a non-monotonous way, the most pronounced signatures showing up for absorbing scatterers. The numerical results compare favourably to the literature results for nonabsorbing spherical scatterers both in and beyond the Rayleigh regime.

Irradiance attenuation coefficient in a stratified ocean - A local property of the medium

NASA Technical Reports Server (NTRS)

Gordon, H. R.

1980-01-01

The influence of optically important constituents of water on the absorption (a) and scattering (b) coefficients and the backscattering probability is considered, with emphasis placed on measuring the volume scattering function (B/theta/). Two stratification models are examined; one in which the phase function (B(theta)/b) is depth independent and only b/c is allowed to vary with optical depth, and the other in which both b/c and the phase function depend on depth. The results demonstrate that Gordon's (1977) technique of estimating a and b is applicable without change to a stratified ocean.

A hybrid asymptotic-modal analysis of the EM scattering by an open-ended S-shaped rectangular waveguide cavity

NASA Technical Reports Server (NTRS)

Law, P. H.; Burkholder, R. J.; Pathak, P. H.

1988-01-01

The electromagnetic fields (EM) backscatter from a 3-dimensional perfectly conducting S-shaped open-ended cavity with a planar interior termination is analyzed when it is illuminated by an external plane wave. The analysis is based on a self-consistent multiple scattering method which accounts for the multiple wave interactions between the open end and the interior termination. The scattering matrices which described the reflection and transmission coefficients of the waveguide modes reflected and transmitted at each junction between the different waveguide sections, as well at the scattering from the edges at the open end are found via asymptotic high frequency methods such as the geometrical and physical theories of diffraction used in conjunction with the equivalent current method. The numerical results for an S-shaped inlet cavity are compared with the backscatter from a straight inlet cavity; the backscattered patterns are different because the curvature of an S-shaped inlet cavity redistributes the energy reflected from the interior termination in a way that is different from a straight inlet cavity.

Theory of CW lidar aerosol backscatter measurements and development of a 2.1 microns solid-state pulsed laser radar for aerosol backscatter profiling

NASA Technical Reports Server (NTRS)

Kavaya, Michael J.; Henderson, Sammy W.; Frehlich, R. G.

1991-01-01

The performance and calibration of a focused, continuous wave, coherent detection CO2 lidar operated for the measurement of atmospheric backscatter coefficient, B(m), was examined. This instrument functions by transmitting infrared (10 micron) light into the atmosphere and collecting the light which is scattered in the rearward direction. Two distinct modes of operation were considered. In volume mode, the scattered light energy from many aerosols is detected simultaneously, whereas in the single particle mode (SPM), the scattered light energy from a single aerosol is detected. The analysis considered possible sources of error for each of these two cases, and also considered the conditions where each technique would have superior performance. The analysis showed that, within reasonable assumptions, the value of B(m) could be accurately measured by either the VM or the SPM method. The understanding of the theory developed during the analysis was also applied to a pulsed CO2 lidar. Preliminary results of field testing of a solid state 2 micron lidar using a CW oscillator is included.

Lidar measurements of wildfire smoke aerosols in the atmosphere above Sofia, Bulgaria

NASA Astrophysics Data System (ADS)

Peshev, Zahary Y.; Deleva, Atanaska D.; Dreischuh, Tanja N.; Stoyanov, Dimitar V.

2016-01-01

Presented are results of lidar measurements and characterization of wildfire caused smoke aerosols observed in the atmosphere above the city of Sofia, Bulgaria, related to two local wildfires raging in forest areas near the city. A lidar systems based on a frequency-doubled Nd:YAG laser operated at 532 nm and 1064 nm is used in the smoke aerosol observations. It belongs to the Sofia LIDAR Station (at Laser Radars Laboratory, Institute of Electronics, Bulgarian Academy of Sciences), being a part of the European Aerosol Lidar Network. Optical, dynamical, microphysical, and geometrical properties and parameters of the observed smoke aerosol particles and layers are displayed and analyzed, such as: range/height-resolved profiles of the aerosol backscatter coefficient; integral aerosol backscattering; sets of colormaps displaying time series of the height distribution of the aerosol density; topologic, geometric, and volumetric properties of the smoke aerosol layers; time-averaged height profiles of backscatter-related Ångström exponent (BAE). Obtained results of retrieving and profiling smoke aerosols are commented in their relations to available meteorological and air-mass-transport forecasting and modelling data.

Specific absorption and backscatter coefficient signatures in southeastern Atlantic coastal waters

NASA Astrophysics Data System (ADS)

Bostater, Charles R., Jr.

1998-12-01

Measurements of natural water samples in the field and laboratory of hyperspectral signatures of total absorption and reflectance were obtained using long pathlength absorption systems (50 cm pathlength). Water was sampled in Indian River Lagoon, Banana River and Port Canaveral, Florida. Stations were also occupied in near coastal waters out to the edge of the Gulf Stream in the vicinity of Kennedy Space Center, Florida and estuarine waters along Port Royal Sound and along the Beaufort River tidal area in South Carolina. The measurements were utilized to calculate natural water specific absorption, total backscatter and specific backscatter optical signatures. The resulting optical cross section signatures suggest different models are needed for the different water types and that the common linear model may only appropriate for coastal and oceanic water types. Mean particle size estimates based on the optical cross section, suggest as expected, that particle size of oceanic particles are smaller than more turbid water types. The data discussed and presented are necessary for remote sensing applications of sensors as well as for development and inversion of remote sensing algorithms.

Responsive BScN Programming at Nipissing University: The Continuing Education of Ontario Nurses

ERIC Educational Resources Information Center

Fitzgerald, Scott; Beattie, Beverley; Carter, Lorraine; Caswell, Wenda

2014-01-01

Nipissing University in North Bay, Ontario, is currently the only post-secondary institution in that province to offer a part-time Baccalaureate of Science in Nursing (BScN) program for Registered Practical Nurses (RPNs) through a blended learning model. This program represents a "bridge" from the nurse's college diploma and offers a…

Entrance Qualifications Affect the Performance of Nutrition Students at University: A Pilot Study

ERIC Educational Resources Information Center

Owusu-Apenten, Richard; Xu, Wen Li

2012-01-01

This study assessed the effect of admissions qualifications on the subsequent academic performances of BSc nutrition students at a UK university. Entrance qualifications for three groups (Grp01, Grp02, Grp03) reading for a BSc(Hons) degree in, Dietetics, Food & Nutrition or Human Nutrition (n = 105) were determined from their UCAS…

Balanced Scorecards in Managing Higher Education Institutions: An Indian Perspective

ERIC Educational Resources Information Center

Umashankar, Venkatesh; Dutta, Kirti

2007-01-01

Purpose: The paper aims to look at the balanced scorecard (BSC) concept and discuss in what way it should be applied to higher education programs/institutions in the Indian context. Design/methodology/approach: The paper is based on extant literature on the balanced scorecard concept per se, as well as applications of BSC in higher education as…

Introducing the Balanced Scorecard: Creating Metrics to Measure Performance

ERIC Educational Resources Information Center

Gumbus, Andra

2005-01-01

This experiential exercise presents the concept of the Balanced Scorecard (BSC) and applies it in a university setting. The Balanced Scorecard was developed 12 years ago and has grown in popularity and is used by more than 50% of the Fortune 500 companies as a performance measurement and strategic management tool. The BSC expands the traditional…

Basic Skill Centers Evaluation, September, 1969 - June, 1971.

ERIC Educational Resources Information Center

Clark, Sara Page

The Basic Skill Centers (BSC) program was developed to help students, primarily from the inner-city Target Area schools of Minneapolis, learn to read. The BSC approach was remedial, and each year more than 700 students, the majority in grades four through six, participated in the program. In 1969-70 the Talking Typewriter was one major aspect of…

78 FR 29754 - Board of Scientific Counselors, National Center for Injury Prevention and Control, (BSC, NCIPC)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-21

... mild-Traumatic Injury Workgroup. There will be 15 minutes allotted for public comments at the end of... Scientific Counselors, National Center for Injury Prevention and Control, (BSC, NCIPC) In accordance with...-being; and (3) conduct and assist in research and control activities related to injury. The Board of...

Liquid Aluminum: Atomic diffusion and viscosity from ab initio molecular dynamics

PubMed Central

Jakse, Noel; Pasturel, Alain

2013-01-01

We present a study of dynamic properties of liquid aluminum using density-functional theory within the local-density (LDA) and generalized gradient (GGA) approximations. We determine the temperature dependence of the self-diffusion coefficient as well the viscosity using direct methods. Comparisons with experimental data favor the LDA approximation to compute dynamic properties of liquid aluminum. We show that the GGA approximation induce more important backscattering effects due to an enhancement of the icosahedral short range order (ISRO) that impact directly dynamic properties like the self-diffusion coefficient. All these results are then used to test the Stokes-Einstein relation and the universal scaling law relating the diffusion coefficient and the excess entropy of a liquid. PMID:24190311

Molecular dynamics of lipid bilayers studied by incoherent quasi-elastic neutron scattering

NASA Astrophysics Data System (ADS)

König, S.; Pfeiffer, W.; Bayerl, T.; Richter, D.; Sackmann, E.

1992-08-01

Molecular motions in highly oriented multilayers of dipalmitoylphosphatidylcholine were studied as a function of temperature and hydration using incoherent quasi-elastic neutron scattering (QENS). The short range diffusive motions of the lipid molecules and the chain/headgroup dynamics were evaluated : 1) by measurement of the dependence of the elastic incoherent structure factor (EISF), the line-width Γ and the dynamic structure factors on the scattering vector Q for two orientations of the sample. The orientations were chosen such that the scattering vecto Q was either predominantly perpendicular or parallel to the membrane normal ; 2) by comparing data from protonated and chain deuterated lipids and 3) by the use of instruments of different energy resolution (i.e. time-of-flight and backscattering spectrometers exploring time regimes of 10^{-13} s to 10^{-11} s and 10^{-11} s to 10^{-9} s respectively). In the fluid phase the time-of-flight spectra revealed a restricted isotropic in-plane and out-of-plane diffusion of the hydrocarbon chain and headgroup protons. The mean displacements range from ≈ 0.6 Å for methylene protons near the glycerol backbone to 7 Å for protons near the chain ends. These values are obtained for a water content of 23 wt%. The values are somewhat increased at 30wt% of water. Measurements of the temperature variation of the EISF and the line-width Γ revealed a remarkably high degree of chain dynamics in the gel (L{β '})-phase. The total elastic intensity as observed with the backscattering instrument showed that L{α}-L{β '}-phase transition is only well expressed at Q-values around 1 Å^{-1}, while the number and mobility of the chain defects characterized at Q≈ 2 Å^{-1} (possibly gtg-kinks) increase continuously between 2 °C and 70 °C. In the time regime explored by the backscattering instrument, motions of the whole lipid molecules are also seen. It was interpreted in terms of a superposition of local in-plane and out-of-plane diffusion and lateral diffusional jumps between adjacent sites as predicted by the free volume model. For a sample containing 12 wt% of water at 60 °C the diffusion coefficient for the out-of-plane motion is D^{allel}=6× 10^{-6} cm2/s with an amplitude of 2.25 Å. In-plane the diffusion coefficients range from D_{min}^{perp}=1.5× 10^{-7} cm2/s to D_{max}^{perp}=6× 10^{-6} cm2/s. The lateral diffusion coefficient is D_lat=9.7× 10^{-8} cm2/s in reasonable agreement with FRAP measurements. The strong increase of the lateral mobility with increasing water content yielded an exponential law for the variation of the diffusion coefficient with excess area per lipid (i.e. hydration) in agreement with the free volume model. The out-of-plane motion is characterized by an amplitude of about 0.5 Å in the time-of-flight time regime and of 2-3 Å in the backscattering time regime. The origin of this discrepancy could be the thermally excited membrane undulations since their relaxation times of ≈ 3× 10^{-9} s (obtained in a separate spin-echo study) agree roughly with the reciprocal line-width of 2.5× 10^{-9} s for the backscattering instrument at Qto 0. The time-of-flight result of 0.5 Å can be attributed to a dynamic surface roughness.

Beam shape coefficients calculation for an elliptical Gaussian beam with 1-dimensional quadrature and localized approximation methods

NASA Astrophysics Data System (ADS)

Wang, Wei; Shen, Jianqi

2018-06-01

The use of a shaped beam for applications relying on light scattering depends much on the ability to evaluate the beam shape coefficients (BSC) effectively. Numerical techniques for evaluating the BSCs of a shaped beam, such as the quadrature, the localized approximation (LA), the integral localized approximation (ILA) methods, have been developed within the framework of generalized Lorenz-Mie theory (GLMT). The quadrature methods usually employ the 2-/3-dimensional integrations. In this work, the expressions of the BSCs for an elliptical Gaussian beam (EGB) are simplified into the 1-dimensional integral so as to speed up the numerical computation. Numerical results of BSCs are used to reconstruct the beam field and the fidelity of the reconstructed field to the given beam field is estimated. It is demonstrated that the proposed method is much faster than the 2-dimensional integrations and it can acquire more accurate results than the LA method. Limitations of the quadrature method and also the LA method in the numerical calculation are analyzed in detail.

Microwave remote sensing of snowpacks

NASA Technical Reports Server (NTRS)

Stiles, W. H.; Ulaby, F. T.

1980-01-01

The interaction mechanisms responsible for the microwave backscattering and emission behavior of snow were investigated, and models were developed relating the backscattering coefficient (sigma) and apparent temperature (T) to the physical parameters of the snowpack. The microwave responses to snow wetness, snow water equivalent, snow surface roughness, and to diurnal variations were investigated. Snow wetness was shown to have an increasing effect with increasing frequency and angle of incidence for both active and passive cases. Increasing snow wetness was observed to decrease the magnitude sigma and increase T. Snow water equivalent was also observed to exhibit a significant influence sigma and T. Snow surface configuration (roughness) was observed to be significant only for wet snow surface conditions. Diurnal variations were as large as 15 dB for sigma at 35 GHz and 120 K for T at 37 GHz. Simple models for sigma and T of a snowpack scene were developed in terms of the most significant ground-truth parameters. The coefficients for these models were then evaluated; the fits to the sigma and T measurements were generally good. Finally, areas of needed additional observations were outlined and experiments were specified to further the understanding of the microwave-snowpack interaction mechanisms.

Airborne Multiwavelength High Spectral Resolution Lidar (HSRL-2) observations during TCAP 2012: vertical profiles of optical and microphysical properties of a smoke/urban haze plume over the northeastern coast of the US

DOE PAGES

Muller, Detlef; Hostetler, Chris A.; Ferrare, R. A.; ...

2014-10-10

Here, we present measurements acquired by the world's first airborne 3 backscatter (β) + 2 extinction (α) High Spectral Resolution Lidar (HSRL-2). HSRL-2 measures particle backscatter coefficients at 355, 532, and 1064 nm, and particle extinction coefficients at 355 and 532 nm. The instrument has been developed by the NASA Langley Research Center. The instrument was operated during Phase 1 of the Department of Energy (DOE) Two-Column Aerosol Project (TCAP) in July 2012. We observed pollution outflow from the northeastern coast of the US out over the western Atlantic Ocean. Lidar ratios were 50–60 sr at 355 nm and 60–70more » sr at 532 nm. Extinction-related Ångström exponents were on average 1.2–1.7, indicating comparably small particles. Our novel automated, unsupervised data inversion algorithm retrieved particle effective radii of approximately 0.2 μm, which is in agreement with the large Angstrom exponents. We find good agreement with particle size parameters obtained from coincident in situ measurements carried out with the DOE Gulfstream-1 aircraft.« less

Nonradiative transport of atomic excitation in Na vapor

NASA Astrophysics Data System (ADS)

Zajonc, Arthur G.; Phelps, A. V.

1981-05-01

Measurements are reported which show the effect of nonradiative losses at a gas-window interface on the backscattered fluorescence intensity for Na vapor at frequencies in the vicinity of the resonance lines near 589 nm. The Na 3P12,32 states are excited with a low-intensity single-mode tunable dye laser at high Na densities and the frequency integral of the backscattered fluorescence intensity in the D1 and D2 lines is measured. As the laser is tuned through resonance, the loss of atomic excitation to the window appears as a sharp decrease in the frequency-integrated fluorescence intensity. For example, at 7×1020 atoms m-3 the fluorescence intensity decreases by a factor of 4 in a frequency interval of 4 GHz. Measured absolute fluorescence intensities versus laser frequency are compared with predictions made using the theory of Hummer and Kunasz which includes both radiative and nonradiative transport processes. The agreement between theory and experiment is remarkably good when one considers that the theory contains only one unknown coefficient, i.e., the reflection coefficient for excited atoms at the windows. In our case the excited atoms are assumed to be completely destroyed at the window.

Contribution of multitemporal polarimetric synthetic aperture radar data for monitoring winter wheat and rapeseed crops

NASA Astrophysics Data System (ADS)

Betbeder, Julie; Fieuzal, Remy; Philippets, Yannick; Ferro-Famil, Laurent; Baup, Frederic

2016-04-01

This paper aims to evaluate the contribution of multitemporal polarimetric synthetic aperture radar (SAR) data for winter wheat and rapeseed crops parameters [height, leaf area index, and dry biomass (DB)] estimation, during their whole vegetation cycles in comparison to backscattering coefficients and optical data. Angular sensitivities and dynamics of polarimetric indicators were also analyzed following the growth stages of these two common crop types using, in total, 14 radar images (Radarsat-2), 16 optical images (Formosat-2, Spot-4/5), and numerous ground data. The results of this study show the importance of correcting the angular effect on SAR signals especially for copolarized signals and polarimetric indicators associated to single-bounce scattering mechanisms. The analysis of the temporal dynamic of polarimetric indicators has shown their high potential to detect crop growth changes. Moreover, this study shows the high interest of using SAR parameters (backscattering coefficients and polarimetric indicators) for crop parameters estimation during the whole vegetation cycle instead of optical vegetation index. They particularly revealed their high potential for rapeseed height and DB monitoring [i.e., Shannon entropy polarimetry (r2=0.70) and radar vegetation index (r2=0.80), respectively].

A Parameterized Inversion Model for Soil Moisture and Biomass from Polarimetric Backscattering Coefficients

NASA Technical Reports Server (NTRS)

Truong-Loi, My-Linh; Saatchi, Sassan; Jaruwatanadilok, Sermsak

2012-01-01

A semi-empirical algorithm for the retrieval of soil moisture, root mean square (RMS) height and biomass from polarimetric SAR data is explained and analyzed in this paper. The algorithm is a simplification of the distorted Born model. It takes into account the physical scattering phenomenon and has three major components: volume, double-bounce and surface. This simplified model uses the three backscattering coefficients ( sigma HH, sigma HV and sigma vv) at low-frequency (P-band). The inversion process uses the Levenberg-Marquardt non-linear least-squares method to estimate the structural parameters. The estimation process is entirely explained in this paper, from initialization of the unknowns to retrievals. A sensitivity analysis is also done where the initial values in the inversion process are varying randomly. The results show that the inversion process is not really sensitive to initial values and a major part of the retrievals has a root-mean-square error lower than 5% for soil moisture, 24 Mg/ha for biomass and 0.49 cm for roughness, considering a soil moisture of 40%, roughness equal to 3cm and biomass varying from 0 to 500 Mg/ha with a mean of 161 Mg/ha

Properties of the water column and bottom derived from Airborne Visible Infrared Imaging Spectrometer (AVIRIS) data

NASA Astrophysics Data System (ADS)

Lee, Zhongping; Carder, Kendall L.; Chen, Robert F.; Peacock, Thomas G.

2001-06-01

Using Airborne Visible Infrared Imaging Spectrometer (AVIRIS) data as an example, we show in this study that the properties of the water column and bottom of a large, shallow area can be adequately retrieved using a model-driven optimization technique. The simultaneously derived properties include bottom depth, bottom albedo, and water absorption and backscattering coefficients, which in turn could be used to derive concentrations of chlorophyll, dissolved organic matter, and suspended sediments in the water column. The derived bottom depths were compared with a bathymetry chart and a boat survey and were found to agree very well. Also, the derived bottom albedo image shows clear spatial patterns, with end-members consistent with sand and seagrass. The image of absorption and backscattering coefficients indicates that the water is quite horizontally mixed. Without bottom corrections, chlorophyll a retrievals were ˜50 mg m-3, while the retrievals after bottom corrections were tenfold less, approximating real values. These results suggest that the model and approach used work very well for the retrieval of subsurface properties of shallow-water environments even for rather turbid environments like Tampa Bay, Florida.

A long Saharan dust event over the western Mediterranean: Lidar, Sun photometer observations, and regional dust modeling

NASA Astrophysics Data System (ADS)

PéRez, C.; Nickovic, S.; Baldasano, J. M.; Sicard, M.; Rocadenbosch, F.; Cachorro, V. E.

2006-08-01

A long Saharan dust event affected the western Mediterranean in the period 12-28 June 2002. Dust was present mainly between 1- and 5-km height affecting most parts of the Iberian Peninsula and reaching western/central Europe. Intensive backscatter lidar observations over Barcelona (Spain) and Sun photometer data from two stations (El Arenosillo, Spain, and Avignon, France) are used to evaluate different configurations the Dust Regional Atmospheric Modeling (DREAM) system. DREAM currently operates dust forecasts over the Mediterranean region (http://www.bsc.es/projects/earthscience/DREAM/) considering four particle size bins while only the first two are relevant for long-range transport analysis since their life time is larger than 12 hours. A more detailed bin method is implemented, and two different dust distributions at sources are compared to the operational version. Evaluations are performed at two wavelengths (532 and 1064 nm). The dust horizontal and vertical structure simulated by DREAM shows very good qualitative agreement when compared to SeaWIFS satellite images and lidar height-time displays over Barcelona. When evaluating the modeled aerosol optical depth (AOD) against Sun photometer data, significant improvements are achieved with the use of the new detailed bin method. In general, the model underpredicts the AOD for increasing Ångström exponents because of the influence of anthropogenic pollution in the boundary layer. In fact, the modeled AOD is highly anticorrelated with the observed Ångström exponents. Avignon shows higher influence of small anthropogenic aerosols which explains the better results of the model at the wavelength of 1064 nm over this location. The uncertainties of backscatter lidar inversions (20-30%) are in the same order of magnitude as the differences between the model experiments. Better model results are obtained when comparing to lidar because most of the anthropogenic effect is removed.

Atmospheric Temperature Profile Measurements Using Mobile High Spectral Resolution Lidar

NASA Astrophysics Data System (ADS)

Razenkov, Ilya I.; Eloranta, Edwin W.

2016-06-01

The High Spectral Resolution Lidar (HSRL) designed at the University of Wisconsin-Madison discriminates between Mie and Rayleigh backscattering [1]. It exploits the Doppler effect caused by thermal motion of molecules, which broadens the spectrum of the transmitted laser light. That allows for absolute calibration of the lidar and measurements of the aerosol volume backscatter coefficient. Two iodine absorption filters with different absorption line widths (a regular iodine vapor filter and Argon buffered iodine filter) allow for atmospheric temperature profile measurements. The sensitivity of the measured signal-to-air temperature ratio is around 0.14%/K. The instrument uses a shared telescope transmitter-receiver design and operates in eyesafe mode (the product of laser average power and telescope aperture equals 0.1 Wm2 at 532 nm).

Optical backscattering properties of the "clearest" natural waters

NASA Astrophysics Data System (ADS)

Twardowski, M. S.; Claustre, H.; Freeman, S. A.; Stramski, D.; Huot, Y.

2007-11-01

During the BIOSOPE field campaign October-December 2004, measurements of inherent optical properties from the surface to 500 m depth were made with a ship profiler at stations covering over 8000 km through the Southeast Pacific Ocean. Data from a ~3000 km section containing the very clearest waters in the central gyre are reported here. The total volume scattering function at 117°, βt(117°), was measured with a WET Labs ECO-BB3 sensor at 462, 532, and 650 nm with estimated uncertainties of 2×10-5, 5×10-6, and 2×10-6 m-1 sr-1, respectively. These values were approximately 6%, 3%, and 3% of the volume scattering by pure seawater at their respective wavelengths. From a methodological perspective, there were several results: - distributions were resolvable even though some of the values from the central gyre were an order of magnitude lower than the lowest previous measurements in the literature; - Direct in-situ measurements of instrument dark offsets were necessary to accurately resolve backscattering at these low levels; - accurate pure seawater backscattering values are critical in determining particulate backscattering coefficients in the open ocean (not only in these very clear waters); the pure water scattering values determined by Buiteveld et al. (1994) with a [1+0.3S/37] adjustment for salinity based on Morel (1974) appear to be the most accurate estimates, with aggregate accuracies as low as a few percent; and - closure was demonstrated with subsurface reflectance measurements reported by Morel et al. (2007) within instrument precisions, a useful factor in validating the backscattering measurements. This methodology enabled several observations with respect to the hydrography and the use of backscattering as a biogeochemical proxy: -The clearest waters sampled were found at depths between 300 and 350 m, from 23.5° S, 118° W to 26° S, 114° W, where total backscattering at 650 nm was not distinguishable from pure seawater; -Distributions of particulate backscattering bbp across the central gyre exhibited a broad particle peak centered ~100 m; -The particulate backscattering ratio typically ranged between 0.4% and 0.6% at 650 nm through the majority of the central gyre from the surface to ~210 m, indicative of "soft" water-filled particles with low bulk refractive index; and - bbp showed a distinct secondary deeper layer centered ~230 m that was absent in particulate attenuation cp data. The particulate backscattering ratio was significantly higher in this layer than in the rest of the water column, reaching 1.2% in some locations. This high relative backscattering, along with the pigment composition and ecological niche of this layer, appear to be consistent with the coccolithophorid Florisphaera profunda. Moreover, results were consistent with several expectations extrapolated from theory and previous work in oceanic and coastal regions, supporting the conclusion that particulate and total backscattering could be resolved in these extremely clear natural waters.

Optical backscattering properties of the "clearest" natural waters

NASA Astrophysics Data System (ADS)

Twardowski, M. S.; Claustre, H.; Freeman, S. A.; Stramski, D.; Huot, Y.

2007-07-01

During the BIOSOPE field campaign October-December 2004, measurements of inherent optical properties from the surface to 500 m depth were made with a ship profiler at stations covering over ~8000 km through the Southeast Pacific Ocean. Data from a ~3000 km section containing the very clearest waters in the central gyre are reported here. The total volume scattering function at 117°, βt(117°), was measured with a WET Labs ECO-BB3 sensor at 462, 532, and 650 nm with estimated uncertainties of 2×10-5, 5×10-6, and 2×10-6 m-1 sr-1, respectively. These values were approximately 6%, 3%, and 3% of the scattering by pure seawater at their respective wavelengths. From a methodological perspective, there were several results: - bbp distributions were resolvable even though some of the values from the central gyre were an order of magnitude lower than the lowest previous measurements in the literature; - Direct in-situ measurements of instrument dark offsets were necessary to accurately resolve backscattering at these low levels; - accurate pure seawater backscattering values are critical in determining particulate backscattering coefficients in the open ocean (not only in these very clear waters); the pure water scattering values determined by Buiteveld et al. (1994) with a [1 + 0.3S/37] adjustment for salinity based on Morel (1974) appear to be the most accurate estimates, with aggregate accuracies as low as a few percent; and - closure was demonstrated with subsurface reflectance measurements reported by Morel et al. (2007) within instrument precisions, a useful factor in validating the backscattering measurements. This methodology enabled several observations with respect to the hydrography and the use of backscattering as a biogeochemical proxy: - The clearest waters sampled were found at depths between 300 and 350 m, from 23.5° S, 118° W to 26° S, 114° W, where total backscattering at 650 nm was not distinguishable from pure seawater; - Distributions of particulate backscattering bbp across the central gyre exhibited a broad particle peak centered ~100 m; - The particulate backscattering ratio typically ranged between 0.4% and 0.6% through the majority of the central gyre from the surface to ~210 m, indicative of "soft" water-filled particles with low bulk refractive index; and - bbp at 532 and 650 nm showed a distinct secondary deeper layer centered ~230 m that was absent in particulate attenuation cp data. The particulate backscattering ratio was significantly higher in this layer than in the rest of the water column, reaching 1.2% in some locations. This high relative backscattering, along with the pigment composition and ecological niche of this layer, appear to be consistent with the coccolithophorid F. profunda. Moreover, results were consistent with several expectations extrapolated from theory and previous work in oceanic and coastal regions, supporting the conclusion that particulate and total backscattering could be resolved in these extremely clear natural waters.

75 FR 1062 - Board of Scientific Counselors, National Center for Injury Prevention and Control, (BSC, NCIPC)

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-08

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, National Center for Injury Prevention and Control, (BSC, NCIPC) In accordance with Section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463), the Centers for Disease Control and Prevention (CDC) announces, the followin...

Characterize Eruptive Processes at Yucca Mountain, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. Krier

2004-10-04

The purpose of this scientific analysis report, ''Characterize Eruptive Processes at Yucca Mountain, Nevada'', is to present information about natural volcanic systems and the parameters that can be used to model their behavior. This information is used to develop parameter-value distributions appropriate for analysis of the consequences of volcanic eruptions through a repository at Yucca Mountain. This scientific analysis report provides information to four other reports: ''Number of Waste Packages Hit by Igneous Intrusion'', (BSC 2004 [DIRS 170001]); ''Atmospheric Dispersal and Deposition of Tephra from Potential Volcanic Eruption at Yucca Mountain, Nevada'' (BSC 2004 [DIRS 170026]); ''Dike/Drift Interactions'' (BSC 2004more » [DIRS 170028]); ''Development of Earthquake Ground Motion Input for Preclosure Seismic Design and Postclosure Performance Assessment of a Geologic Repository at Yucca Mountain, NV'' (BSC 2004 [DIRS 170027], Section 6.5). This report is organized into seven major sections. This section addresses the purpose of this document. Section 2 addresses quality assurance, Section 3 the use of software, Section 4 identifies the requirements that constrain this work, and Section 5 lists assumptions and their rationale. Section 6 presents the details of the scientific analysis and Section 7 summarizes the conclusions reached.« less

Balanced scorecard: application in the General Panarcadian Hospital of Tripolis, Greece.

PubMed

Koumpouros, Yiannis

2013-01-01

The purpose of this paper is to discuss the application of the balanced scorecard (BSC) in the Greek public health sector. The basic balanced scorecard theory has been adopted in the characteristics and individualities of the Greek public health system. The theoretical model developed was applied in the General Panarcadian Hospital of Tripolis (GPHT) in Greece. GPHT is a representative paradigm of a big regional Greek public hospital. It has about 300 beds and many clinics and specialties (internal medicine, cardiology, general surgery, intensive care unit, artificial kidney unit, etc.). Strategic management was performed for almost three years. The BSC model was formulated in an appropriate software program. The problems (both technical and managerial) faced during a three-year period along with the results of this management approach are presented in the current paper. The paper highlights some important gaps in the Greek public health system, while proposing actions to be taken. The BSC theory can be very successful under certain conditions. Special attention is given to the peculiarities of the Greek public health situation. The paper presents for the first time a real life example of applying BSC in the Greek public health sector.

DNA methylation analysis from saliva samples for epidemiological studies.

PubMed

Nishitani, Shota; Parets, Sasha E; Haas, Brian W; Smith, Alicia K

2018-06-18

Saliva is a non-invasive, easily accessible tissue, which is regularly collected in large epidemiological studies to examine genetic questions. Recently, it is becoming more common to use saliva to assess DNA methylation. However, DNA extracted from saliva is a mixture of both bacterial and human DNA derived from epithelial and immune cells in the mouth. Thus, there are unique challenges to using salivary DNA in methylation studies that can influence data quality. This study assesses: (1) quantification of human DNA after extraction; (2) delineation of human and bacterial DNA; (3) bisulfite conversion (BSC); (4) quantification of BSC DNA; (5) PCR amplification of BSC DNA from saliva and; (6) quantitation of DNA methylation with a targeted assay. The framework proposed will allow saliva samples to be more widely used in targeted epigenetic studies.

Nondestructive Method For Measuring The Scattering Coefficient Of Bulk Material

NASA Astrophysics Data System (ADS)

Groenhuis, R. A. J.; ten Bosch, J. J.

1981-05-01

During demineralization and remineralization of dental enamel its structure changes resulting in a change of the absorption and scattering coefficients of the enamel. By measuring these coefficients during demineralization and remineralization these processes can be monitored in a non-destructive way. For this purpose an experimental arrangement was made: a fibre illuminates a spot on the sample with monochromatic light with a wave-length between 400 nm and 700 nm; a photomultiplier measures the luminance of the light back-scattered by the sample as a function of the distance from the measuring snot to the spot of illumination. In a Monte Carlo-model this luminance is simulated using the same geometry given the scattering and absorption coefficients in a sample. Then the scattering and absorption coefficients in the sample are determined by selecting the theoretical curve fitting the experimental one. Scattering coefficients below 10 mm-1 and absorption coefficients obtained with this method on calibration samples correspond well with those obtained with another method. Scattering coefficients above 10 mm-1 (paper samples) were measured ton low. This perhaps is caused by the anisotropic structure of paper sheets. The method is very suitable to measure the scattering and absorption coefficients of bulk materials.

Stochastic inversion of ocean color data using the cross-entropy method.

PubMed

Salama, Mhd Suhyb; Shen, Fang

2010-01-18

Improving the inversion of ocean color data is an ever continuing effort to increase the accuracy of derived inherent optical properties. In this paper we present a stochastic inversion algorithm to derive inherent optical properties from ocean color, ship and space borne data. The inversion algorithm is based on the cross-entropy method where sets of inherent optical properties are generated and converged to the optimal set using iterative process. The algorithm is validated against four data sets: simulated, noisy simulated in-situ measured and satellite match-up data sets. Statistical analysis of validation results is based on model-II regression using five goodness-of-fit indicators; only R2 and root mean square of error (RMSE) are mentioned hereafter. Accurate values of total absorption coefficient are derived with R2 > 0.91 and RMSE, of log transformed data, less than 0.55. Reliable values of the total backscattering coefficient are also obtained with R2 > 0.7 (after removing outliers) and RMSE < 0.37. The developed algorithm has the ability to derive reliable results from noisy data with R2 above 0.96 for the total absorption and above 0.84 for the backscattering coefficients. The algorithm is self contained and easy to implement and modify to derive the variability of chlorophyll-a absorption that may correspond to different phytoplankton species. It gives consistently accurate results and is therefore worth considering for ocean color global products.

Coherent scattering of a spherical wave from an irregular surface. [antenna pattern effects

NASA Technical Reports Server (NTRS)

Fung, A. K.

1983-01-01

The scattering of a spherical wave from a rough surface using the Kirchhoff approximation is considered. An expression representing the measured coherent scattering coefficient is derived. It is shown that the sphericity of the wavefront and the antenna pattern can become an important factor in the interpretation of ground-based measurements. The condition under which the coherent scattering-coefficient expression reduces to that corresponding to a plane wave incidence is given. The condition under which the result reduces to the standard image solution is also derived. In general, the consideration of antenna pattern and sphericity is unimportant unless the surface-height standard deviation is small, i.e., unless the coherent scattering component is significant. An application of the derived coherent backscattering coefficient together with the existing incoherent scattering coefficient to interpret measurements from concrete and asphalt surfaces is shown.

Acoustic characterization of Thiel liver for magnetic resonance-guided focused ultrasound treatment.

PubMed

Karakitsios, Ioannis; Joy, Joyce; Mihcin, Senay; Melzer, Andreas

2017-04-01

The purpose of this work was to measure the essential acoustic parameters, i.e., acoustic impedance, reflection coefficient, attenuation coefficient, of Thiel embalmed human and animal liver. The Thiel embalmed tissue can be a promising, pre-clinical model to study liver treatment with Magnetic Resonance-guided Focused Ultrasound (MRgFUS). Using a single-element transducer and the contact pulse-echo method, the acoustic parameters, i.e., acoustic impedance, reflection coefficient and attenuation coefficient of Thiel embalmed human and animal liver were measured. The Thiel embalmed livers had higher impedance, similar reflection and lower attenuation compared to the fresh tissue. Embalming liver with Thiel fluid affects its acoustic properties. During MRgFUS sonication of a Thiel organ, more focused ultrasound (FUS) will be backscattered by the organ, and higher acoustic powers are required to reach coagulation levels (temperatures >56 °C).

Role of G protein-coupled receptors (GPCR), matrix metalloproteinases 2 and 9 (MMP2 and MMP9), heparin-binding epidermal growth factor-like growth factor (hbEGF), epidermal growth factor receptor (EGFR), erbB2, and insulin-like growth factor 1 receptor (IGF-1R) in trenbolone acetate-stimulated bovine satellite cell proliferation.

PubMed

Thornton, K J; Kamange-Sollo, E; White, M E; Dayton, W R

2015-09-01

Implanting cattle with steroids significantly enhances feed efficiency, rate of gain, and muscle growth. However, the mechanisms responsible for these improvements in muscle growth have not been fully elucidated. Trenbolone acetate (TBA), a testosterone analog, has been shown to increase proliferation rate in bovine satellite cell (BSC) cultures. The classical genomic actions of testosterone have been well characterized; however, our results indicate that TBA may also initiate a quicker, nongenomic response that involves activation of G protein-coupled receptors (GPCR) resulting in activation of matrix metalloproteinases 2 and 9 (MMP2 and MMP9) that release membrane-bound heparin-binding epidermal growth factor-like growth factor (hbEGF), which then binds to and activates the epidermal growth factor receptor (EGFR) and/or erbB2. Furthermore, the EGFR has been shown to regulate expression of the IGF-1 receptor (IGF-1R), which is well known for its role in modulating muscle growth. To determine whether this nongenomic pathway is potentially involved in TBA-stimulated BSC proliferation, we analyzed the effects of treating BSC with guanosine 5'-O-2-thiodiphosphate (GDPβS), an inhibitor of all GPCR; a MMP2 and MMP9 inhibitor (MMPI); CRM19, a specific inhibitor of hbEGF; AG1478, a specific EGFR tyrosine kinase inhibitor; AG879, a specific erbB2 kinase inhibitor; and AG1024, an IGF-1R tyrosine kinase inhibitor on TBA-stimulated proliferation rate (H-thymidine incorporation). Assays were replicated at least 9 times for each inhibitor experiment using BSC cultures obtained from at least 3 different animals. Bovine satellite cell cultures were obtained from yearling steers that had no previous exposure to androgenic or estrogenic compounds. As expected, BSC cultures treated with 10 n TBA showed ( < 0.05) increased proliferation rate when compared with control cultures. Additionally, treatment with 5 ng hbEGF/mL stimulated proliferation in BSC cultures ( < 0.05). Treatment with GDPβS, MMPI, CRM197, AG1024, AG1478, and/or AG879 all suppressed ( < 0.05) TBA-induced increases in proliferation. These data indicate that TBA likely initiates a nongenomic response involving GPCR, MMP2 and MMP9, hbEGF, EGFR, erbB2, and IGF-1R, which may play a role in TBA-mediated increases in BSC proliferation.

Quantitative ultrasound imaging for monitoring in situ high-intensity focused ultrasound exposure.

PubMed

Ghoshal, Goutam; Kemmerer, Jeremy P; Karunakaran, Chandra; Abuhabsah, Rami; Miller, Rita J; Sarwate, Sandhya; Oelze, Michael L

2014-10-01

Quantitative ultrasound (QUS) imaging is hypothesized to map temperature elevations induced in tissue with high spatial and temporal resolution. To test this hypothesis, QUS techniques were examined to monitor high-intensity focused ultrasound (HIFU) exposure of tissue. In situ experiments were conducted on mammary adenocarcinoma tumors grown in rats and lesions were formed using a HIFU system. A thermocouple was inserted into the tumor to provide estimates of temperature at one location. Backscattered time-domain waveforms from the tissue during exposure were recorded using a clinical ultrasonic imaging system. Backscatter coefficients were estimated using a reference phantom technique. Two parameters were estimated from the backscatter coefficient (effective scatterer diameter (ESD) and effective acoustic concentration (EAC). The changes in the average parameters in the regions corresponding to the HIFU focus over time were correlated to the temperature readings from the thermocouple. The changes in the EAC parameter were consistently correlated to temperature during both heating and cooling of the tumors. The changes in the ESD did not have a consistent trend with temperature. The mean ESD and EAC before exposure were 120 ± 16 μm and 32 ± 3 dB/cm3, respectively, and changed to 144 ± 9 μm and 51 ± 7 dB/cm3, respectively, just before the last HIFU pulse was delivered to the tissue. After the tissue cooled down to 37 °C, the mean ESD and EAC were 126 ± 8 μm and 35 ± 4 dB/cm3, respectively. Peak temperature in the range of 50-60 °C was recorded by a thermocouple placed just behind the tumor. These results suggest that QUS techniques have the potential to be used for non-invasive monitoring of HIFU exposure. © The Author(s) 2014.

Aerosol Abundances and Optical Characteristics in the Pacific Basin Free Troposphere

NASA Technical Reports Server (NTRS)

Pueschel, R. F.; Livingston, J. M.; Ferry, G. V.; deFelice, T. E.

1994-01-01

During NASA's Global Backscatter Experiment (GLOBE) mission flights in November 1989 and May 1990, a DC-8 research aircraft probed the Pacific Basin free troposphere for about 90 flight hours in each month between +72 and -62 degrees latitude, +130 and -120 degrees longitude, and up to 39,000 feet pressure altitudes. Aerosols were sampled continuously in situ by optical particle counters to measure concentration and particle size, and during 48 10-min intervals during each mission by wire impactors for concentration, size, composition, phase and shape analyses. The optical particle counters cover a particle diameter range between 0.3 and 20 microns; wire impactors extend the range down to 0.03 microns. Results of particle number, size, shape, together with the assumption of a refractive index corresponding to (NH4)2SO4 to account for the prevalence of aerosol sulfur, were utilized in a Mie algorithm to calculate aerosol extinction and backscatter for a range of wavelengths (0.385 less than lambda less than 10.64 microns). Computations for 22 randomly selected size distributions yield coefficients of extinction E(0.525) = (2.03 +/- 1.20) x 10(exp -4) km(exp -1) and backscatter beta(0.525) = (6.45 +/- 3.49) x 10(exp -6) km(exp -1) sr(exp -1) in the visible, and E(10.64) = (8.13 +/- 6.47) x 10(exp -6) km(exp -1) and beta(10.64) = (9.98 +/- 10.69) x 10(exp -8) km(exp -1) sr(exp -1) in the infrared, respectively. Large particles (D greater than 0.3 microns) contribute two-thirds to the total extinction in the visible (lambda = 0.525 microns), and almost 100% in the infrared (lambda = 10.64 microns). These results have been used to define an IR optical aerosol climatology of the Pacific Basin free troposphere, from which it follows that the infrared backscatter coefficient at lambda = 9.25 microns wavelength fluctuates between 5.0 x 10(exp -10) and 2.0 x 10(exp -7) km(exp -1) sr(exp -1) with a modal value 2.0 x 10(exp -8) km(exp -1) sr(exp -1).

Changes in BSc Business Administration and Psychology Students' Learning Styles over One, Two and Three Years of Study

ERIC Educational Resources Information Center

Nielsen, Tine

2013-01-01

Knowledge on general or discipline-specific changes in the learning styles of university students can be utilised in the design and execution of courses, but little is known of such changes. The study examined the changes in the learning styles of three year groups of BSc Business Administration and Psychology students from admittance to one, two…

Establishing Information Security Systems via Optical Imaging

DTIC Science & Technology

2015-08-11

SLM, spatial light modulator; BSC, non - polarizing beam splitter cube; CCD, charge-coupled device. In computational ghost imaging, a series of...Laser Object Computer Fig. 5. A schematic setup for the proposed method using holography: BSC, Beam splitter cube; CCD, Charge-coupled device. The...interference between reference and object beams . (a) (e) (d) (c) (b) Distribution Code A: Approved for public release, distribution is unlimited

Prevalence of obesity in the equine population of Saskatoon and surrounding area.

PubMed

Kosolofski, Hayley R; Gow, Sheryl P; Robinson, Katherine A

2017-09-01

A retrospective study determined the prevalence of obesity and over-conditioning in horses in Saskatoon, Saskatchewan. Body condition score (BSC) was assessed for 290 horses from the Field Service practice at the Western College of Veterinary Medicine. The median BSC of horses was 6; however, 59 (20.3%) horses were classified as over-conditioned, and 24 (8.3%) as obese.

News from the Biological Stain Commission No. 5.

PubMed

Lyon, H O; Dapson, R W

2009-06-01

In this fifth issue of News from the Biological Stain Commission (BSC), under the heading of Regulatory Affairs, the BSC's International Affairs Committee provides more information from the meeting of the International Standards Organization ISO/TC 212 Committee that took place on June 2-4, 2008 at Vancouver, Canada. In addition, we give an update on the current situation regarding the supplies of hematoxylin.

Active Engagement with Assessment and Feedback Can Improve Group-Work Outcomes and Boost Student Confidence

ERIC Educational Resources Information Center

Scott, G. W.

2017-01-01

This study involves evaluation of a novel iterative group-based learning task developed to enable students to actively engage with assessment and feedback in order to improve the quality of their written work. The students were all in the final semester of their final year of study and enrolled on either BSc Zoology or BSc Marine and Freshwater…

[Balanced Scorecard--a business tool for profit calculations--usable in gynecology and obstetrics?].

PubMed

Goerke, K

2001-08-01

The balanced scorecard (BSC) is an instrument of business administration using score numbers, that not only includes financial aspects but also levels of communication, motivation and customer relations. Thus it seems usable in service oriented companies including hospitals. The next years will have to show, whether the results rectify the immense expenses necessary with the implementation of the BSC.

Final Analysis of Outcomes and RAS/BRAF Status in a Randomized Phase 3 Study of Panitumumab and Best Supportive Care in Chemorefractory Wild Type KRAS Metastatic Colorectal Cancer.

PubMed

Kim, Tae Won; Elme, Anneli; Park, Joon Oh; Udrea, Anghel Adrian; Kim, Sun Young; Ahn, Joong Bae; Valencia, Ricardo Villalobos; Krishnan, Srinivasan; Manojlovic, Nebojsa; Guan, Xuesong; Lofton-Day, Catherine; Jung, A Scott; Vrdoljak, Eduard

2018-03-21

Tumor rat sarcoma gene (RAS) status is a negative predictive biomarker for anti-epidermal growth factor receptor (EGFR) therapy in metastatic colorectal cancer (mCRC). We analyzed outcomes according to RAS and v-Raf murine sarcoma viral oncogene homolog B (BRAF) mutational status, and evaluated early tumor shrinkage (ETS) and depth of response (DpR) for patients with wild type RAS. Patients with confirmed metastatic colon or rectum adenocarcinoma, wild type Kristen rat sarcoma gene tumor exon 2 status, clinical/radiologic disease progression or toxicity during irinotecan or oxaliplatin treatment, and no previous anti-EGFR therapy were randomized 1:1 to receive best supportive care (BSC) with or without panitumumab (6.0 mg/kg, intravenously, on day 1 of each 14-day cycle) in this open-label, multicenter, phase III study (20100007). RAS and BRAF mutation status were determined using Sanger sequencing. ETS was evaluated as maximum percentage change from baseline to week 8; DpR was calculated as the percentage change for tumor shrinkage at nadir versus baseline. Overall, 270 patients had RAS wild type mCRC (panitumumab with BSC, n = 142; BSC, n = 128). For patients with wild type RAS tumors, median overall survival (OS; hazard ratio [HR], 0.72; P = .015) and progression-free survival (PFS; HR, 0.45; P < .0001) were improved with panitumumab with BSC versus BSC. Similar improvements were seen for patients with wild type RAS, and wild type BRAF tumors (OS: HR, 0.75; P = .04; PFS: HR, 0.45; P < .0001). Median DpR was 16.9% for the evaluable panitumumab with BSC wild type RAS population. Overall, 69.5% experienced any type of tumor shrinkage at week 8; 38.2% experienced ≥ 20% shrinkage. Similar improvements in OS and PFS were seen with stratification according to ETS. This analysis showed that panitumumab improved outcomes in wild type RAS mCRC and indicated that ETS and DpR could be used as additional efficacy markers. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

Optical-microphysical properties of Saharan dust aerosols and composition relationship using a multi-wavelength Raman lidar, in situ sensors and modelling: a case study analysis

NASA Astrophysics Data System (ADS)

Papayannis, A.; Mamouri, R. E.; Amiridis, V.; Remoundaki, E.; Tsaknakis, G.; Kokkalis, P.; Veselovskii, I.; Kolgotin, A.; Nenes, A.; Fountoukis, C.

2012-05-01

A strong Saharan dust event that occurred over the city of Athens, Greece (37.9° N, 23.6° E) between 27 March and 3 April 2009 was followed by a synergy of three instruments: a 6-wavelength Raman lidar, a CIMEL sun-sky radiometer and the MODIS sensor. The BSC-DREAM model was used to forecast the dust event and to simulate the vertical profiles of the aerosol concentration. Due to mixture of dust particles with low clouds during most of the reported period, the dust event could be followed by the lidar only during the cloud-free day of 2 April 2009. The lidar data obtained were used to retrieve the vertical profile of the optical (extinction and backscatter coefficients) properties of aerosols in the troposphere. The aerosol optical depth (AOD) values derived from the CIMEL ranged from 0.33-0.91 (355 nm) to 0.18-0.60 (532 nm), while the lidar ratio (LR) values retrieved from the Raman lidar ranged within 75-100 sr (355 nm) and 45-75 sr (532 nm). Inside a selected dust layer region, between 1.8 and 3.5 km height, mean LR values were 83 ± 7 and 54 ± 7 sr, at 355 and 532 nm, respectively, while the Ångström-backscatter-related (ABR355/532) and Ångström-extinction-related (AER355/532) were found larger than 1 (1.17 ± 0.08 and 1.11 ± 0.02, respectively), indicating mixing of dust with other particles. Additionally, a retrieval technique representing dust as a mixture of spheres and spheroids was used to derive the mean aerosol microphysical properties (mean and effective radius, number, surface and volume density, and mean refractive index) inside the selected atmospheric layers. Thus, the mean value of the retrieved refractive index was found to be 1.49( ± 0.10) + 0.007( ± 0.007)i, and that of the effective radiuses was 0.30 ± 0.18 μm. The final data set of the aerosol optical and microphysical properties along with the water vapor profiles obtained by Raman lidar were incorporated into the ISORROPIA II model to provide a possible aerosol composition consistent with the retrieved refractive index values. Thus, the inferred chemical properties showed 12-40% of dust content, sulfate composition of 16-60%, and organic carbon content of 15-64%, indicating a possible mixing of dust with haze and smoke. PM10 concentrations levels, PM10 composition results and SEM-EDX (Scanning Electron Microscope-Energy Dispersive X-ray) analysis results on sizes and mineralogy of particles from samples during the Saharan dust transport event were used to evaluate the retrieval.

The role of non-rainfall water on physiological activation in desert biological soil crusts

NASA Astrophysics Data System (ADS)

Zheng, Jiaoli; Peng, Chengrong; Li, Hua; Li, Shuangshuang; Huang, Shun; Hu, Yao; Zhang, Jinli; Li, Dunhai

2018-01-01

Non-rainfall water (NRW, e.g. fog and dew), in addition to rainfall and snowfall, are considered important water inputs to drylands. At the same time, biological soil crusts (BSCs) are important components of drylands. However, little information is available regarding the effect of NRW inputs on BSC activation. In this study, the effects of NRW on physiological activation in three BSC successional stages, including the cyanobacteria crust stage (Crust-C), moss colonization stage (Crust-CM), and moss crust stage (Crust-M), were studied in situ. Results suggest NRW inputs hydrated and activated physiological activity (Fv/Fm, carbon exchange, and nitrogen fixation) in BSCs but led to a negative carbon balance and low rates of nitrogen fixation in BSCs. One effective NRW event could hydrate BSCs for 7 h. Following simulated rainfall, the physiological activities recovered within 3 h, and net carbon gain occurred until 3 h after hydration, whereas NRW-induced physiological recovery processes were slower and exhibited lower activities, leading to a negative carbon balance. There were significant positive correlations between NRW amounts and the recovered values of Fv/Fm in all the three BSC stages (p < .001). The thresholds for Fv/Fm activation decreased with BSC succession, and the annual effective NRW events increased with BSC succession, with values of 29.8, 89.2, and 110.7 in Crust-C, Crust-CM and Crust-M, respectively. The results suggest that moss crust and moss-cyanobacteria crust use NRW to prolong metabolic activity and reduce drought stress more efficiently than cyanobacteria crusts. Therefore, these results suggest that BSCs utilize NRW to sustain life while growth and biomass accumulation require precipitation (rainfall) events over a certain threshold.

Comparison of broad-spectrum cephalosporin-resistant Escherichia coli isolated from dogs and humans in Hokkaido, Japan.

PubMed

Okubo, Torahiko; Sato, Toyotaka; Yokota, Shin-ichi; Usui, Masaru; Tamura, Yutaka

2014-04-01

Resistance to broad-spectrum cephalosporins (BSCs) in Enterobacteriaceae in companion animals has become a great concern for public health. To estimate the dissemination of BSC-resistant bacteria between dog and human, we examined the BSC-resistance determinants of and genetic similarities between 69 BSC-resistant Escherichia coli isolates derived from canine rectal swabs (n = 28) and human clinical samples (n = 41). Some E. coli isolates possessed blaTEM-1b (14 canine and 16 human isolates), blaCTx-M-2 (6 human isolates), blaCTx-M-14 (3 canine and 14 human isolates), blaCTx-M-27 (1 canine and 15 human isolates), and blaCMY-2 (11 canine and 3 human isolates). The possession of CTX-M-type β-lactamases was significantly more frequent in human isolates, whereas CMY-2 was more common in canine isolates. Bacterial typing methods (phylogenetic typing, O-antigen serotyping, and pulsed-field gel electrophoresis) showed little clonal relationship between canine isolates and human isolates. Plasmid analysis and Southern blotting indicated that the plasmids encoding CMY-2 were similar among canine and human isolates. Based on the differences in the major β-lactamase and the divergence of bacterial types between canine and human isolates, it seems that clonal dissemination of BSC-resistant E. coli between canines and humans is limited. The similarity of the CMY-2-encoding plasmid suggests that plasmid-mediated β-lactamase gene transmission plays a role in interspecies diffusion of BSC-resistant E. coli between dog and human. Copyright © 2013 Japanese Society of Chemotherapy and The Japanese Association for Infectious Diseases. Published by Elsevier Ltd. All rights reserved.

Application and verification of the NMMB/BSC-CTM forecast for solar energy

NASA Astrophysics Data System (ADS)

Soret, Albert; Serradell, Kim; Piot, Matthias; Ortega, Daniel; Obiso, Vincenzo; Jorba, Oriol

2016-04-01

In the beginning of April 2014, northern Europe was affected by a mineral dust intrusion. On 4 April 2014, the power prediction for German solar installations was estimated as 21 GW, whereas the measured power production merely reached 11 GW. This strong overestimation significantly affected the hourly price in the wholesale electricity market: prices were firstly assessed at around 27 € /MWh but rapidly reached a level close to 150 € /MWh after recognizing the lack of solar output. It has been found that a large proportion of the uncertainty of existing NWP models can be attributed to the lack of accurate aerosol data used in order to model solar radiation. Despite the advancements in the modelling of aerosol-cloud interactions, current meteorological models use parameterizations made mostly for climate considerations (generally monthly-based). In this contribution, we analyse model results of the direct radiative effect of mineral dust over Germany at the beginning of April 2014. For that, the NMMB/BSC Chemical Transport Model (NMMB/BSC-CTM) is applied on a regional domain at 0.1° horizontal resolution. The NMMB/BSC-CTM is a new on-line chemical weather prediction system coupling atmospheric and chemistry processes. In the radiation module of the model, mineral dust is treated as a radiatively active substance interacting both short and longwave radiation. The impact of the mineral dust outbreaks on meteorology is discussed by comparing model forecasts meteorological observations. The analysis focuses on the performance of the NMMB/BSC-CTM to simulate the radiative effects of a mineral dust intrusion far from source regions. Model results would help to illustrate the added value of on-line models for long term analysis of solar resource. On-going developments: integration of anthropogenic sources and implementation of indirect radiative effects will be also presented.

Concepts and definitions for "supportive care," "best supportive care," "palliative care," and "hospice care" in the published literature, dictionaries, and textbooks.

PubMed

Hui, David; De La Cruz, Maxine; Mori, Masanori; Parsons, Henrique A; Kwon, Jung Hye; Torres-Vigil, Isabel; Kim, Sun Hyun; Dev, Rony; Hutchins, Ronald; Liem, Christiana; Kang, Duck-Hee; Bruera, Eduardo

2013-03-01

Commonly used terms such as "supportive care," "best supportive care," "palliative care," and "hospice care" were rarely and inconsistently defined in the palliative oncology literature. We conducted a systematic review of the literature to further identify concepts and definitions for these terms. We searched MEDLINE, PsycInfo, EMBASE, and CINAHL for published peer-reviewed articles from 1948 to 2011 that conceptualized, defined, or examined these terms. Two researchers independently reviewed each citation for inclusion and then extracted the concepts/definitions when available. Dictionaries/textbooks were also searched. Nine of 32 "SC/BSC," 25 of 182 "PC," and 12 of 42 "HC" articles focused on providing a conceptual framework/definition. Common concepts for all three terms were symptom control and quality-of-life for patients with life-limiting illness. "SC" focused more on patients on active treatment compared to other categories (9/9 vs. 8/37) and less often involved interdisciplinary care (4/9 vs. 31/37). In contrast, "HC" focused more on volunteers (6/12 vs. 6/34), bereavement care (9/12 vs. 7/34), and community care (9/12 vs. 6/34). Both "PC" and "SC/BSC" were applicable earlier in the disease trajectory (16/34 vs. 0/9). We found 13, 24, and 17 different definitions for "SC/BSC," "PC," and "HC," respectively. "SC/BSC" was the most variably defined, ranging from symptom management during cancer therapy to survivorship care. Dictionaries/textbooks showed similar findings. We identified defining concepts for "SC/BSC," "PC," and "HC" and developed a preliminary conceptual framework unifying these terms along the continuum of care to help build consensus toward standardized definitions.

Atmospheric aerosols: Their Optical Properties and Effects (supplement)

NASA Technical Reports Server (NTRS)

1976-01-01

A digest of technical papers is presented. Topics include aerosol size distribution from spectral attenuation with scattering measurements; comparison of extinction and backscattering coefficients for measured and analytic stratospheric aerosol size distributions; using hybrid methods to solve problems in radiative transfer and in multiple scattering; blue moon phenomena; absorption refractive index of aerosols in the Denver pollution cloud; a two dimensional stratospheric model of the dispersion of aerosols from the Fuego volcanic eruption; the variation of the aerosol volume to light scattering coefficient; spectrophone in situ measurements of the absorption of visible light by aerosols; a reassessment of the Krakatoa volcanic turbidity, and multiple scattering in the sky radiance.

Label-free hyperspectral dark-field microscopy for quantitative scatter imaging

NASA Astrophysics Data System (ADS)

Cheney, Philip; McClatchy, David; Kanick, Stephen; Lemaillet, Paul; Allen, David; Samarov, Daniel; Pogue, Brian; Hwang, Jeeseong

2017-03-01

A hyperspectral dark-field microscope has been developed for imaging spatially distributed diffuse reflectance spectra from light-scattering samples. In this report, quantitative scatter spectroscopy is demonstrated with a uniform scattering phantom, namely a solution of polystyrene microspheres. A Monte Carlo-based inverse model was used to calculate the reduced scattering coefficients of samples of different microsphere concentrations from wavelength-dependent backscattered signal measured by the dark-field microscope. The results are compared to the measurement results from a NIST double-integrating sphere system for validation. Ongoing efforts involve quantitative mapping of scattering and absorption coefficients in samples with spatially heterogeneous optical properties.

Determination of particles concentration in Black Sea waters from spectral beam attenuation coefficient

NASA Astrophysics Data System (ADS)

Korchemkina, E. N.; Latushkin, A. A.; Lee, M. E.

2017-11-01

The methods of determination of concentration and scattering by suspended particles in seawater are compared. The methods considered include gravimetric measurements of the mass concentration of suspended matter, empirical and analytical calculations based on measurements of the light beam attenuation coefficient (BAC) in 4 spectral bands, calculation of backscattering by particles using satellite measurements in the visible spectral range. The data were obtained in two cruises of the R/V "Professor Vodyanitsky" in the deep-water part of the Black Sea in July and October 2016., Spatial distribution of scattering by marine particles according to satellite data is in good agreement with the contact measurements.

Adapting the balanced scorecard for mental health and addictions: an inpatient example.

PubMed

Lin, Elizabeth; Durbin, Janet

2008-05-01

The Balanced Scorecard (BSC) is a performance-monitoring framework that originated in the business sector but has more recently been applied to health services. The province of Ontario is using the BSC approach to monitor quality of inpatient care in five service areas. Feasibility of the scorecard framework for each area has been assessed using a standard approach. This paper reports results of the feasibility study for the mental health sector, focusing on three issues: framework relevance, underlying strategic goals and indicator selection. Based on a literature review and extensive stakeholder input, the BSC quadrant structure was recommended with some modifications, and indicators were selected that aligned with provincial mental health reform policy goals. The mental health report has completed two cycles of reporting, and has received good support from the field. Copyright © 2008 Longwoods Publishing.

Using path analysis to examine causal relationships among balanced scorecard performance indicators for general hospitals: the case of a public hospital system in Taiwan.

PubMed

Yang, Ming-Chin; Tung, Yu-Chi

2006-01-01

Examining whether the causal relationships among the performance indicators of the balanced scorecard (BSC) framework exist in hospitals is the aim of this article. Data were collected from all twenty-one general hospitals in a public hospital system and their supervising agency for the 3-year period, 2000-2002. The results of the path analyses identified significant causal relationships among four perspectives in the BSC model. We also verified the relationships among indicators within each perspective, some of which varied as time changed. We conclude that hospital administrators can use path analysis to help them identify and manage leading indicators when adopting the BSC model. However, they should also validate causal relationships between leading and lagging indicators periodically because the management environment changes constantly.

He-Ne and CW CO2 laser long-path systems for gas detection

NASA Technical Reports Server (NTRS)

Grant, W. B.

1986-01-01

This paper describes the design and testing of a laboratory prototype dual He-Ne laser system for the detection of methane leaks from underground pipelines and solid-waste landfill sites using differential absorption of radiation backscattered from topographic targets. A laboratory-prototype dual CW carbon dioxide laser system also using topographic backscatter is discussed, and measurement results for methanol are given. With both systems, it was observed that the time-varying differential absorption signal was useful in indicating the presence of a gas coming from a nearby source. Limitations to measurement sensitivity, especially the role of speckle and atmospheric turbulence, are described. The speckle results for hard targets are contrasted with those from atmospheric aerosols. The appendix gives appropriate laser lines and values of absorption coefficients for the hydrazine fuel gases.

Model of lidar range-Doppler signatures of solid rocket fuel plumes

NASA Astrophysics Data System (ADS)

Bankman, Isaac N.; Giles, John W.; Chan, Stephen C.; Reed, Robert A.

2004-09-01

The analysis of particles produced by solid rocket motor fuels relates to two types of studies: the effect of these particles on the Earth's ozone layer, and the dynamic flight behavior of solid fuel boosters used by the NASA Space Shuttle. Since laser backscatter depends on the particle size and concentration, a lidar system can be used to analyze the particle distributions inside a solid rocket plume in flight. We present an analytical model that simulates the lidar returns from solid rocket plumes including effects of beam profile, spot size, polarization and sensing geometry. The backscatter and extinction coefficients of alumina particles are computed with the T-matrix method that can address non-spherical particles. The outputs of the model include time-resolved return pulses and range-Doppler signatures. Presented examples illustrate the effects of sensing geometry.

Measurement and calibration of differential Mueller matrix of distributed targets

NASA Technical Reports Server (NTRS)

Sarabandi, Kamal; Oh, Yisok; Ulaby, Fawwaz T.

1992-01-01

A rigorous method for calibrating polarimetric backscatter measurements of distributed targets is presented. By characterizing the radar distortions over the entire mainlobe of the antenna, the differential Mueller matrix is derived from the measured scattering matrices with a high degree of accuracy. It is shown that the radar distortions can be determined by measuring the polarimetric response of a metallic sphere over the main lobe of the antenna. Comparison of results obtained with the new algorithm with the results derived from the old calibration method show that the discrepancy between the two methods is less than 1 dB for the backscattering coefficients. The discrepancy is more drastic for the phase-difference statistics, indicating that removal of the radar distortions from the cross products of the scattering matrix elements cannot be accomplished with the traditional calibration methods.

The radar cross section of dielectric disks

NASA Technical Reports Server (NTRS)

Levine, D. M.

1982-01-01

A solution is presented for the backscatter (nonstatic) radar cross section of dielectric disks of arbitrary shape, thickness and dielectric constant. The result is obtained by employing a Kirchhoff type approximation to obtain the fields inside the disk. The internal fields induce polarization and conduction currents from which the scattered fields and the radar cross section can be computed. The solution for the radar cross section obtained in this manner is shown to agree with known results in the special cases of normal incidence, thin disks and perfect conductivity. The solution can also be written as a product of the reflection coefficient of an identically oriented slab times the physical optics solution for the backscatter cross section of a perfectly conducting disk of the same shape. This result follows directly from the Kirchhoff type approximation without additional assumptions.

Laser Induced Patterning of Transparent Ceramics and Metallic Thin Films for Photonic and Sensing Applications

DTIC Science & Technology

2014-01-31

Department Chair Mechanical Engineering UC Riverside gaguilar@engr.ucr.edu Javier Garay Program Chair Materials and Engineering UC Riverside...Students: Miroslava Cano-Lara (PhD CICESE) # Yasmin Esqueda-Barron ( MSc , PhD CICESE)* Gabriel Castillo-Vega ( MSc CICESE, PhD USAL) # Rene Rodriguez...Beltran ( MSc , CICESE) # Lidia Sanchez-Hernandez (BSc UAEM) # Adela Reyes-Contreras (BSc UAEM) # Postdocs: Israel Perez (Postdoc, 4 months) USA

The Sleep of the Saved and Thankful

DTIC Science & Technology

2009-03-16

the media working with the BSC, including Henry Luce, publisher of Time, Life and Fortune magazines; Walter Lippmann, columnist for the Herald Tribune...Walter Winchell, whose syndicated gossip column was read by over 50 million people in more than 2,000 papers worldwide; Arthur H. Sulzberger...York Herald Tribune, the New York Post, and the Baltimore Sun, – the places where the BSC had the most success in finding sympathetic columnists and

Classification of kidney and liver tissue using ultrasound backscatter data

NASA Astrophysics Data System (ADS)

Aalamifar, Fereshteh; Rivaz, Hassan; Cerrolaza, Juan J.; Jago, James; Safdar, Nabile; Boctor, Emad M.; Linguraru, Marius G.

2015-03-01

Ultrasound (US) tissue characterization provides valuable information for the initialization of automatic segmentation algorithms, and can further provide complementary information for diagnosis of pathologies. US tissue characterization is challenging due to the presence of various types of image artifacts and dependence on the sonographer's skills. One way of overcoming this challenge is by characterizing images based on the distribution of the backscatter data derived from the interaction between US waves and tissue. The goal of this work is to classify liver versus kidney tissue in 3D volumetric US data using the distribution of backscatter US data recovered from end-user displayed Bmode image available in clinical systems. To this end, we first propose the computation of a large set of features based on the homodyned-K distribution of the speckle as well as the correlation coefficients between small patches in 3D images. We then utilize the random forests framework to select the most important features for classification. Experiments on in-vivo 3D US data from nine pediatric patients with hydronephrosis showed an average accuracy of 94% for the classification of liver and kidney tissues showing a good potential of this work to assist in the classification and segmentation of abdominal soft tissue.

A Study of Solar Flare Effects on Mid and High Latitude Radio Wave Propagation using SuperDARN.

NASA Astrophysics Data System (ADS)

Ruohoniemi, J. M.; Chakraborty, S.; Baker, J. B.

2017-12-01

Over the Horizon (OTH) communication is strongly dependent on the state of the ionosphere, which is sensitive to solar X-ray flares. The Super Dual Auroral Radar Network (SuperDARN), whose working principle is dependent on trans-ionospheric radio communication, uses HF radio waves to remotely sense the ionosphere. The backscatter returns from the terrestrial surface (also known as ground-scatter) transit the ionosphere four times and simulate the operation of an HF communications link. SuperDARN backscatter signal properties are altered (strongly attenuated and changes apparent phase) during a sudden ionospheric disturbance following a solar flare, commonly known as Short-Wave Fadeout or SWF. During an SWF the number of SuperDARN backscatter echoes drops suddenly (≈1 min) and sharply, often to near zero, and recovers within 30 minutes to an hour. In this study HF propagation data (SuperDARN backscatter) obtained during SWF events are analyzed for the purpose of validating and improving the performance of HF absorption models, such as, Space Weather Prediction Center (SWPC) D-region Absorption model (DRAP) and CCMC physics based AbbyNormal model. We will also present preliminary results from a physics based model for the mid and high latitude ionospheric response to flare-driven space weather anomalies, which can be used to estimate different physical parameters of the ionosphere such as electron density, collision frequency, absorption coefficients, response time of D-region etc.

Radar backscattering measurement of bare soil and vegetation covered soil using X-band and full polarization

NASA Astrophysics Data System (ADS)

Goswami, B.; Kalita, M.

2014-11-01

The objective of the study is to measure backscattered power of bare soil and vegetation covered soil using X-band scatterometer system with full polarization and various angles during monsoon season and relate backscattered power to the density of vegetation over soil. The measurement was conducted at an experimental field located in the campus of Assam Engineering College, Guwahati, India. The soil sample consists of Silt and Clay in higher proportions as compared to Sand. The scatterometer system consists of dual-polarimetric square horn antennas, Power meter, Klystron, coaxial cables, isolator and waveguide detector. The polarization of the horn antennas as well as the look angle can be changed in the set-up. The backscattering coefficients were calculated by applying a radar equation for the measured values at incident angles between 30° and 60° for full polarization (HH, VV, HV, VH), respectively, and compared with vegetation cover over soil for each scatterometer measurement simultaneously. The VH polarization and 60° look angle are found to be the most suitable combination of configuration of an X-band scatterometer for distinguishing the land cover targets such as bare soil and vegetation covered soil. From the analysis of the results, polarimetric scatterometer data appear to be promising to distinguish the land cover types such as bare soil and soil completely covered by vegetation. The results of this study will help the scientists working in the field of active microwave remote sensing.

Seasonal variability of dust in the eastern Mediterranean (Athens, Greece), through lidar measurements in the frame of EARLINET (2002-2012)

NASA Astrophysics Data System (ADS)

Kokkalis, Panos; Papayannis, Alex; Tsaknakis, George; Mamouri, RodElise; Argyrouli, Athina

2013-04-01

Aerosols play an important role in earth's atmospheric radiation balance, which is enhanced in areas where dust is mostly present (e.g. the Mediterranean region), as in the case of the city of Athens. The focus of this paper is to provide a comprehensive analysis of the seasonal variability of optical and geometrical properties, as well as the mass concentration of Saharan dust over the city of Athens, Greece, for a 10-years time period: 2002-2012 based on the laser remote sensing (lidar) technique. More specifically, the aerosol optical properties concern the extinction and the backscatter coefficient, as well as the lidar ratio, while the geometrical properties concern the dust layer thickness and center of mass. The calculations of the aerosol extinction coefficient and of the so-called lidar ratio (defined as the ratio of the aerosol extinction coefficient over the aerosol backscatter coefficient) are made by using the Raman lidar technique, only under cloud-free conditions. The calculation of the dust mass concentration was retrieved by a applying a conversion factor (the so-called dust extinction cross section; mean value of the order of 0.64 m2g-1) and by combining sun photometric measurements and modeled dust loading values. Our data analysis was based on monthly-mean values, and only in time periods under cloud-free conditions and for lidar signals with signal to noise ratios (SNR) greater than 1.5 under dusty conditions. The mean value of the lidar ratio at 355 nm was found to be 62±20sr, while the mean dust mass concentration was of the order of 240 μgm-3. The data analyzed were obtained by systematic aerosol lidar measurements performed by the EOLE Raman lidar system of the National Technical University of Athens (NTUA), in the frame of the European Aerosol Research Lidar network (EARLINET). EOLE is able to provide the vertical profiles of the aerosol backscatter (at 355, 532, 1064 nm) and extinction coefficients (at 355 and 532 nm), as well as the water vapor mixing ratio, from about 700 m up to 10000 m, with high temporal (< 5 min.) and spatial (7.5 m) resolution. Acknowledgements: This research has been co-financed by the European Union (European Social Fund - ESF) and Greek national funds through the Operational Program "Education and Lifelong Learning" of the National Strategic Reference Framework (NSRF) - Research Funding Program: Heracleitus II - Investing in knowledge society through the European Social Fund. This research was also financially supported by ITARS (www.itars.net), European Union Seventh Framework Programme (FP7/2007-2013): People, ITN Marie Curie Actions Programme (2012-2016) under grant agreement no 289923.

Lung cancer mortality and exposure to polycyclic aromatic hydrocarbons in British coke oven workers.

PubMed

Miller, Brian G; Doust, Emma; Cherrie, John W; Hurley, J Fintan

2013-10-16

Workers on coke oven plants may be exposed to potentially carcinogenic polycyclic aromatic hydrocarbons (PAHs), particularly during work on the ovens tops. Two cohorts, employees of National Smokeless Fuels (NSF) and the British Steel Corporation (BSC) totalling more than 6,600 British coke plant workers employed in 1967, had been followed up to mid-1987 for mortality. Previous analyses suggested an excess in lung cancer risk of around 25%, or less when compared with Social Class IV ('partly skilled').Analyses based on internal comparisons within the cohorts identified statistical associations with estimates of individual exposures, up to the start of follow-up, to benzene-soluble materials (BSM), widely used as a metric for mixtures of PAHs. Some associations were also found with times spent in certain coke ovens jobs with specific exposure scenarios, but results were not consistent across the two cohorts and limitations in the exposure estimates were noted. The present study was designed to reanalyse the existing data on lung cancer mortality, incorporating revised and improved exposure estimates to BSM and to benzo[a]pyrene (B[a]P), including increments during the follow-up and a lag for latency. Mean annual average concentrations of both BSM and B[a]P were estimated by analysis of variance (ANOVA) from concentration measurements at all NSF and six BSC plants, and summarised by job and plant, with a temporal trend (for the BSM only). These were combined with subjects' work histories, to produce exposure estimates in each year of follow-up, with a 10-year lag to allow for latency. Exposures to BSM and to B[a]P were sufficiently uncorrelated to permit analysis in relation to each variable separately.Lung cancer death risks during the follow-up were analysed in relation to the estimated time-dependent exposures, both continuous and grouped, using Cox regression models, with adjustment for age. Changing the exposure estimates changed the estimated relative risks compared with earlier results, but the new analyses showed no significant trends with continuous measures of exposure to either BSM or B[a]P, nor with time spent on ovens tops. Analyses with grouped exposures showed mixed results. Across all BSC plants, the relative risk coefficient for working 5 or more years on ovens tops, where the exposures were highest, was 1.81, which was statistically significant. However, results for those with 0-5 years on ovens tops did not suggest a trend; the evidence for an underlying relationship was thus suggestive but not strong. The new results are in line with previous findings; they show some signs consistent with an effect of coke ovens work on lung cancer risk, especially on ovens tops, but the preponderant absence of significant results, and the inconsistencies between results for NSF and BSC, highlight how little evidence there is in these data of any effect.

Lung cancer mortality and exposure to polycyclic aromatic hydrocarbons in British coke oven workers

PubMed Central

2013-01-01

Background Workers on coke oven plants may be exposed to potentially carcinogenic polycyclic aromatic hydrocarbons (PAHs), particularly during work on the ovens tops. Two cohorts, employees of National Smokeless Fuels (NSF) and the British Steel Corporation (BSC) totalling more than 6,600 British coke plant workers employed in 1967, had been followed up to mid-1987 for mortality. Previous analyses suggested an excess in lung cancer risk of around 25%, or less when compared with Social Class IV (‘partly skilled’). Analyses based on internal comparisons within the cohorts identified statistical associations with estimates of individual exposures, up to the start of follow-up, to benzene-soluble materials (BSM), widely used as a metric for mixtures of PAHs. Some associations were also found with times spent in certain coke ovens jobs with specific exposure scenarios, but results were not consistent across the two cohorts and limitations in the exposure estimates were noted. The present study was designed to reanalyse the existing data on lung cancer mortality, incorporating revised and improved exposure estimates to BSM and to benzo[a]pyrene (B[a]P), including increments during the follow-up and a lag for latency. Methods Mean annual average concentrations of both BSM and B[a]P were estimated by analysis of variance (ANOVA) from concentration measurements at all NSF and six BSC plants, and summarised by job and plant, with a temporal trend (for the BSM only). These were combined with subjects’ work histories, to produce exposure estimates in each year of follow-up, with a 10-year lag to allow for latency. Exposures to BSM and to B[a]P were sufficiently uncorrelated to permit analysis in relation to each variable separately. Lung cancer death risks during the follow-up were analysed in relation to the estimated time-dependent exposures, both continuous and grouped, using Cox regression models, with adjustment for age. Results Changing the exposure estimates changed the estimated relative risks compared with earlier results, but the new analyses showed no significant trends with continuous measures of exposure to either BSM or B[a]P, nor with time spent on ovens tops. Analyses with grouped exposures showed mixed results. Across all BSC plants, the relative risk coefficient for working 5 or more years on ovens tops, where the exposures were highest, was 1.81, which was statistically significant. However, results for those with 0–5 years on ovens tops did not suggest a trend; the evidence for an underlying relationship was thus suggestive but not strong. Conclusions The new results are in line with previous findings; they show some signs consistent with an effect of coke ovens work on lung cancer risk, especially on ovens tops, but the preponderant absence of significant results, and the inconsistencies between results for NSF and BSC, highlight how little evidence there is in these data of any effect. PMID:24131617

Earlinet single calculus chain: new products overview

NASA Astrophysics Data System (ADS)

D'Amico, Giuseppe; Mattis, Ina; Binietoglou, Ioannis; Baars, Holger; Mona, Lucia; Amato, Francesco; Kokkalis, Panos; Rodríguez-Gómez, Alejandro; Soupiona, Ourania; Kalliopi-Artemis, Voudouri

2018-04-01

The Single Calculus Chain (SCC) is an automatic and flexible tool to analyze raw lidar data using EARLINET quality assured retrieval algorithms. It has been already demonstrated the SCC can retrieve reliable aerosol backscatter and extinction coefficient profiles for different lidar systems. In this paper we provide an overview of new SCC products like particle linear depolarization ratio, cloud masking, aerosol layering allowing relevant improvements in the atmospheric aerosol characterization.

Earlinet validation of CATS L2 product

NASA Astrophysics Data System (ADS)

Proestakis, Emmanouil; Amiridis, Vassilis; Kottas, Michael; Marinou, Eleni; Binietoglou, Ioannis; Ansmann, Albert; Wandinger, Ulla; Yorks, John; Nowottnick, Edward; Makhmudov, Abduvosit; Papayannis, Alexandros; Pietruczuk, Aleksander; Gialitaki, Anna; Apituley, Arnoud; Muñoz-Porcar, Constantino; Bortoli, Daniele; Dionisi, Davide; Althausen, Dietrich; Mamali, Dimitra; Balis, Dimitris; Nicolae, Doina; Tetoni, Eleni; Luigi Liberti, Gian; Baars, Holger; Stachlewska, Iwona S.; Voudouri, Kalliopi-Artemis; Mona, Lucia; Mylonaki, Maria; Rita Perrone, Maria; João Costa, Maria; Sicard, Michael; Papagiannopoulos, Nikolaos; Siomos, Nikolaos; Burlizzi, Pasquale; Engelmann, Ronny; Abdullaev, Sabur F.; Hofer, Julian; Pappalardo, Gelsomina

2018-04-01

The Cloud-Aerosol Transport System (CATS) onboard the International Space Station (ISS), is a lidar system providing vertically resolved aerosol and cloud profiles since February 2015. In this study, the CATS aerosol product is validated against the aerosol profiles provided by the European Aerosol Research Lidar Network (EARLINET). This validation activity is based on collocated CATS-EARLINET measurements and the comparison of the particle backscatter coefficient at 1064nm.

The Hyperspectral Imager for the Coastal Ocean (HICO): Sensor and Data Processing Overview

DTIC Science & Technology

2010-01-20

backscattering coefficients, and others. Several of these software modules will be developed within the Automated Processing System (APS), a data... Automated Processing System (APS) NRL developed APS, which processes satellite data into ocean color data products. APS is a collection of methods...used for ocean color processing which provide the tools for the automated processing of satellite imagery [1]. These tools are in the process of

Innovative Techniques for High-Resolution Imaging and Precision Tracking

DTIC Science & Technology

1990-04-20

field-of-view ladar. 6 𔄁 The bipath method employs two separate single-ended ladar systems to measure both the backscattering and extinction coefficients... Transmissometer measurements are very important not only for determining the overall accuracy of the proposed system but also for assessing its performance under...the maximum path length difference between the target elements. The necessary laser power can be deduced from the system resolution requirement. The

Demonstration of Aerosol Property Profiling by Multi-wavelength Lidar Under Varying Relative Humidity Conditions

NASA Technical Reports Server (NTRS)

Whiteman, D.N.; Veselovskii, I.; Kolgotin, A.; Korenskii, M.; Andrews, E.

2008-01-01

The feasibility of using a multi-wavelength Mie-Raman lidar based on a tripled Nd:YAG laser for profiling aerosol physical parameters in the planetary boundary layer (PBL) under varying conditions of relative humidity (RH) is studied. The lidar quantifies three aerosol backscattering and two extinction coefficients and from these optical data the particle parameters such as concentration, size and complex refractive index are retrieved through inversion with regularization. The column-integrated, lidar-derived parameters are compared with results from the AERONET sun photometer. The lidar and sun photometer agree well in the characterization of the fine mode parameters, however the lidar shows less sensitivity to coarse mode. The lidar results reveal a strong dependence of particle properties on RH. The height regions with enhanced RH are characterized by an increase of backscattering and extinction coefficient and a decrease in the Angstrom exponent coinciding with an increase in the particle size. We present data selection techniques useful for selecting cases that can support the calculation of hygroscopic growth parameters using lidar. Hygroscopic growth factors calculated using these techniques agree with expectations despite the lack of co-located radiosonde data. Despite this limitation, the results demonstrate the potential of multi-wavelength Raman lidar technique for study of aerosol humidification process.

Inherent optical properties and satellite retrieval of chlorophyll concentration in the lagoon and open ocean waters of New Caledonia.

PubMed

Dupouy, Cécile; Neveux, Jacques; Ouillon, Sylvain; Frouin, Robert; Murakami, Hiroshi; Hochard, Sébastien; Dirberg, Guillaume

2010-01-01

The retrieval of chlorophyll-a concentration from remote sensing reflectance (Rrs) data was tested with the NASA OC4v4 algorithm on the inner New Caledonian lagoon (Case 2) and adjacent open ocean (Case 1) waters. The input to OC4v4 was Rrs measured in situ or modeled from water's inherent optical properties (2001-2007). At open ocean stations, backscattering and absorption coefficients were correlated with chlorophyll (R(2)=0.31-0.51, respectively), in agreement with models for Case 1 waters. Taking spectrofluorometric measurement as reference, the OC4v4 model leads to an average underestimation of 33% of the chlorophyll concentration. For the lagoon waters, OC4v4 performed inadequately because the backscattering coefficient, highly correlated with turbidity and suspended matter (R(2)=0.98), was poorly correlated to chlorophyll (R(2)=0.42). The OC4v4 performance was better in deep lagoon waters for stations with a TDT index (Tchla x depth/turbidity) higher than 19 mg m(-2) NTU(-1) (R(2)=0.974, bias=10.2%). Global Imager Rrs provided a good estimate of Tchla (R(2)=0.79, N=28) in the deeper part of the lagoon. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Designing and Using Projects with Real World Application in a MBA Managerial Accounting Class: The Case of The Balanced Scorecard

ERIC Educational Resources Information Center

Houke, Charlotte

2017-01-01

This paper explores the purpose of designing and using projects with real world application in a M.B.A. managerial accounting class. Included is a discussion of how and why the Balanced Scorecard (BSC) Project has been used in classes to link theory with practice by providing real world application of the BSC framework. M.B.A. students represent a…

Active G protein-coupled receptors (GPCR), matrix metalloproteinases 2/9 (MMP2/9), heparin-binding epidermal growth factor (hbEGF), epidermal growth factor receptor (EGFR), erbB2, and insulin-like growth factor 1 receptor (IGF-1R) are necessary for trenbolone acetate-induced alterations in protein turnover rate of fused bovine satellite cell cultures.

PubMed

Thornton, K J; Kamanga-Sollo, E; White, M E; Dayton, W R

2016-06-01

Trenbolone acetate (TBA), a testosterone analog, increases protein synthesis and decreases protein degradation in fused bovine satellite cell (BSC) cultures. However, the mechanism through which TBA alters these processes remains unknown. Recent studies indicate that androgens improve rate and extent of muscle growth through a nongenomic mechanism involving G protein-coupled receptors (GPCR), matrix metalloproteinases (MMP), heparin-binding epidermal growth factor (hbEGF), the epidermal growth factor receptor (EGFR), erbB2, and the insulin-like growth factor-1 receptor (IGF-1R). We hypothesized that TBA activates GPCR, resulting in activation of MMP2/9 that releases hbEGF, which activates the EGFR and/or erbB2. To determine whether the proposed nongenomic pathway is involved in TBA-mediated alterations in protein turnover, fused BSC cultures were treated with TBA in the presence or absence of inhibitors for GPCR, MMP2/9, hbEGF, EGFR, erbB2, or IGF-1R, and resultant protein synthesis and degradation rates were analyzed. Assays were replicated at least 9 times for each inhibitor experiment utilizing BSC cultures obtained from at least 3 different steers that had no previous exposure to steroid compounds. As expected, fused BSC cultures treated with 10 n TBA exhibited increased ( < 0.05) protein synthesis rates and decreased ( < 0.05) protein degradation rates when compared to control cultures. Treatment of fused BSC cultures with 10 n TBA in the presence of inhibitors for GPCR, MMP2/9, hbEGF, EGFR, erbB2, or IGF-1R suppressed ( < 0.05) TBA-mediated increases in protein synthesis rate. Alternatively, inhibition of GPCR, MMP2/9, hbEGF, EGFR, erbB2, or IGF-1R in the presence of 10 n TBA each had no ( > 0.05) effect on TBA-mediated decreases in protein degradation. However, inhibition of both EGFR and erbB2 in the presence of 10 n TBA resulted in decreased ( < 0.05) ability of TBA to decrease protein degradation rate. Additionally, fused BSC cultures treated with 10 n TBA exhibit increased ( < 0.05) pAKT protein levels. These data indicate the TBA-mediated increases in protein synthesis likely involve GPCR, MMP2/9, hbEGF, EGFR, erbB2, and IGF-1R. However, the mechanism through which TBA mediates changes in protein degradation is different and appears to involve only the EGFR and erbB2. Furthermore, it appears the protein kinase B pathway is involved in TBA's effects on fused BSC cultures.

The Ni-Cu-PGE mineralized Brejo Seco mafic-ultramafic layered intrusion, Riacho do Pontal Orogen: Onset of Tonian (ca. 900 Ma) continental rifting in Northeast Brazil

NASA Astrophysics Data System (ADS)

Salgado, Silas Santos; Ferreira Filho, Cesar Fonseca; Caxito, Fabrício de Andrade; Uhlein, Alexandre; Dantas, Elton Luiz; Stevenson, Ross

2016-10-01

The Brejo Seco mafic-ultramafic Complex (BSC) occurs at the extreme northwest of the Riacho do Pontal Orogen Internal Zone, in the northern margin of the São Francisco Craton in Northeast Brazil. The stratigraphy of this medium size (3.5 km wide and 9 km long) layered intrusion consists of four main zones, from bottom to top: Lower Mafic Zone (LMZ; mainly troctolite), Ultramafic Zone (UZ; mainly dunite and minor troctolite); Transitional Mafic Zone (TMZ; mainly troctolite) and an Upper Mafic Zone (UMZ; gabbro and minor anorthosite, troctolite, and ilmenite magnetitite). Ni-Cu-PGE mineralization occurs at the contact of the UZ with the TMZ, consisting of an up to 50 m thick stratabound zone of disseminated magmatic sulfides. An Mg-tholeiitic affinity to the parental magma is indicated by the geochemical fractionation pattern, by the magmatic crystallization sequence and by the elevated Fo content in olivine. A Smsbnd Nd isochron yielded an age of 903 ± 20 Ma, interpreted as the age of crystallization, with initial εNd = 0.8. Evidence of interaction of the BSC parental magma with sialic crust is given by the Rare Earth and trace element patterns, and by slightly negative and overall low values of εNd(900 Ma) in between -0.2 and +3.3. Contrary to early interpretations that it might constitute an ophiolite complex, based mainly on the geochemistry of the host rocks (Morro Branco metavolcanosedimentary complex), here we interpret the BSC as a typical layered mafic-ultramafic intrusion in continental crust, related to an extensional regime. The BSC is chrono-correlated to mafic dyke swarms, anorogenic granites and thick bimodal volcanics of similar age and tectonic setting in the São Francisco Craton and surrounding areas. Intrusion of the BSC was followed by continued lithospheric thinning, which led to the development of the Paulistana Complex continental rift volcanics around 888 Ma and ultimately to plate separation and the generation of new oceanic crust (Monte Orebe Complex) around 820-650 Ma ago. Thus, the BSC provides a benchmark for the onset of Tonian continental rifting in this area, and is an important marker for the processes of Rodinia breakup and dispersion recorded in South America.

MULTIPLY: Development of a European HSRL Airborne Facility

NASA Astrophysics Data System (ADS)

Binietoglou, Ioannis; Serikov, Ilya; Nicolae, Doina; Amiridis, Vassillis; Belegante, Livio; Boscornea, Andrea; Brugmann, Bjorn; Costa Suros, Montserrat; Hellmann, David; Kokkalis, Panagiotis; Linne, Holger; Stachlewska, Iwona; Vajaiac, Sorin-Nicolae

2016-08-01

MULTIPLY is a novel airborne high spectral resolution lidar (HSRL) currently under development by a consortium of European institutions from Romania, Germany, Greece, and Poland. Its aim is to contribute to calibration and validations activities of the upcoming ESA aerosol sensing missions like ADM-Aeolus, EarthCARE and the Sentinel-3/-4/-5/-5p which include products related to atmospheric aerosols. The effectiveness of these missions depends on independent airborne measurements to develop and test the retrieval methods, and validate mission products following launch. The aim of ESA's MULTIPLY project is to design, develop, and test a multi-wavelength depolarization HSRL for airborne applications. The MULTIPLY lidar will deliver the aerosol extinction and backscatter coefficient profiles at three wavelengths (355nm, 532nm, 1064nm), as well as profiles of aerosol intensive parameters (Ångström exponents, extinction- to-backscatter ratios, and linear particle depolarization ratios).

Results of a study on polarization mix selection for the NSCAT scatterometer

NASA Technical Reports Server (NTRS)

Long, David G.; Dunbar, R. Scott; Shaffer, Scott; Freilich, Michael H.; Hsiao, S. Vincent

1989-01-01

The NASA scatterometer (NSCAT) is an instrument designed to measure the radar backscatter of the ocean's surface for estimating the near-surface wind velocity. A given resolution element is observed from several different azimuth angles. From these measurements the near-surface vector wind over the ocean may be inferred using a geophysical model function relating the normalized radar backscatter coefficient (sigma0) to the near-surface wind. The results of a study to select a polarization mix for NSCAT using an end-to-end simulation of the NSCAT scatterometer and ground processing of the sigma0 measurements into unambiguous wind fields using a median-filter-based ambiguity-removal algorithm are presented. The system simulation was used to compare the wind measurement accuracy and ambiguity removal skill over a set of realistic mesoscale wind fields for various polarization mixes. Considerations in the analysis and simulation are discussed, and a recommended polarization mix is given.

Using the balanced scorecard to mobilize human resources in organizational transformation.

PubMed

Tsasis, Peter; Harber, Bruce

2008-05-01

Traditionally, the balanced scorecard (BSC) has been an effective tool in linking measurement to strategy. However, what is least understood is how the BSC can be used to redefine organizational relationships, re-engineer fundamental processes and transform organizational culture, for superior performance in an organization with the same people, services and technology that previously delivered dismal performance. This paper highlights the process and uses York Central Hospital in Toronto, Ontario, Canada as an illustrative example.

Acoustic Evaluation and Recommended Controls for Runway Supervisory Units, Laughlin AFB, Texas.

DTIC Science & Technology

1980-02-01

NR ), given in Table 2 and shown in Figures 8 through 12 , are the arithmetic differences between exterior and interior noise levels. No difference...ORG. REPORT MUM4MR , ,IT]VPARINACCI, Capt, USAF- BSC Consultant, Acoustics Evaluation Engr CAROLYN M. JONES, 2LT USAF, BSC Consultant, Industria ...Documents.,") Block 12 . Report Date. Enter here the day, month, and year or month and year as shown on the cover, Block 13. Number of Pages. Enter

Economic analysis of blood product transfusions according to the treatment of acute myeloid leukemia in the elderly.

PubMed

Cannas, G; Fattoum, J; Boukhit, M; Thomas, X

2015-01-01

Blood transfusion requirement represents one of the most significant cost driver associated with acute myeloid leukemia (AML). Low-intensity treatments (low-dose cytarabine, hypomethylating agents) have the potential to reduce transfusion dependence, and improve health-related quality of life. We assessed the cost-effectiveness of treatment types regarding blood product transfusions in a cohort of 214 AML patients aged ≥ 70 years. Analyzes did not indicate any significant overall survival (OS) advantage of intensive chemotherapy comparatively to low-intensity treatment. The difference was significant when compared to best supportive care (BSC) (P<0.0001). Blood products transfusion cost per patient was 1.3 times lower with low-intensity therapy and 2.7 times lower with BSC than with intensive chemotherapy. Mean transfusion cost per patient according to OS varied from 2.4 to 1.3 times less with low-intensity treatment comparatively to intensive chemotherapy for patients having OS ≤ 13.3 months. Costs varied from 3.5 to 2.6 times less with BSC comparatively to intensive chemotherapy. In contrast, mean transfusion costs were comparable among treatments for patients with OS>13.3 months. Low-intensity treatments represent a cost-effective alternative to BSC and require a reduced number of transfused blood products comparatively to intensive chemotherapy, while OS was not significantly different. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Application of the balanced scorecard to an academic medical center in Taiwan: the effect of warning systems on improvement of hospital performance.

PubMed

Chen, Hsueh-Fen; Hou, Ying-Hui; Chang, Ray-E

2012-10-01

The balanced scorecard (BSC) is considered to be a useful tool for management in a variety of business environments. The purpose of this article is to utilize the experimental data produced by the incorporation and implementation of the BSC in hospitals and to investigate the effects of the BSC red light tracking warning system on performance improvement. This research was designed to be a retrospective follow-up study. The linear mixed model was applied for correcting the correlated errors. The data used in this study were secondary data collected by repeated measurements taken between 2004 and 2010 by 67 first-line medical departments of a public academic medical center in Taipei, Taiwan. The linear mixed model of analysis was applied for multilevel analysis. Improvements were observed with various time lags, from the subsequent month to three months after red light warning. During follow-up, the red light warning system more effectively improved controllable costs, infection rates, and the medical records completion rate. This further suggests that follow-up management promotes an enhancing and supportive effect to the red light warning. The red light follow-up management of BSC is an effective and efficient tool where improvement depends on ongoing and consistent attention in a continuing effort to better administer medical care and control costs. Copyright © 2012. Published by Elsevier B.V.

Density-dependent regulation of growth of BSC-1 cells in cell culture: control of growth by serum factors.

PubMed Central

Holley, R W; Armour, R; Baldwin, J H; Brown, K D; Yeh, Y C

1977-01-01

BSC-1 cells grow slowly, to high cell density, in medium with 0.1% calf serum. An increase in the serum concentration increases both the growth rate of the cells and the final cell density. The serum can be replaced to some extent by epidermal growth factor (EGF). Initiation of DNA synthesis in BSC-1 cells that have spread into a "wound" in a crowded cell layer requires the addition of a trace of serum or EGF, if the cells have previously been deprived of serum. The binding of 125I-labeled EGF to low-density and high-density BSC-1 cells has been studied. Binding is faster to low-density cells. Cells at low cell density also bind much more EGF per cell than cells at high cell density. The fraction of bound 125I-labeled EGF that is present on the cell surface as intact EGF is larger at low than at high cell density. The results indicate that the number of available EGF receptors per cell decreases drastically as the cell density increases. It is suggested that a decrease in the number of available EGF receptor sites per cell, and the accompanying decrease in sensitivity of the cells to EGF, contributes to density-dependent regulation of growth of these cells. Images PMID:303774

Uncertainties of optical parameters and their propagations in an analytical ocean color inversion algorithm.

PubMed

Lee, ZhongPing; Arnone, Robert; Hu, Chuanmin; Werdell, P Jeremy; Lubac, Bertrand

2010-01-20

Following the theory of error propagation, we developed analytical functions to illustrate and evaluate the uncertainties of inherent optical properties (IOPs) derived by the quasi-analytical algorithm (QAA). In particular, we evaluated the effects of uncertainties of these optical parameters on the inverted IOPs: the absorption coefficient at the reference wavelength, the extrapolation of particle backscattering coefficient, and the spectral ratios of absorption coefficients of phytoplankton and detritus/gelbstoff, respectively. With a systematically simulated data set (46,200 points), we found that the relative uncertainty of QAA-derived total absorption coefficients in the blue-green wavelengths is generally within +/-10% for oceanic waters. The results of this study not only establish theoretical bases to evaluate and understand the effects of the various variables on IOPs derived from remote-sensing reflectance, but also lay the groundwork to analytically estimate uncertainties of these IOPs for each pixel. These are required and important steps for the generation of quality maps of IOP products derived from satellite ocean color remote sensing.

The role of nonmagnetic d{sup 0} vs. d{sup 10}B-type cations on the magnetic exchange interactions in osmium double perovskites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, Hai L., E-mail: Hai.Feng@cpfs.mpg.de; Yamaura, Kazunari; Tjeng, Liu Hao

Polycrystalline samples of double perovskites Ba{sub 2}BOsO{sub 6} (B=Sc, Y, In) were synthesized by solid state reactions. They adopt the cubic double perovskite structures (space group, Fm-3m) with ordered B and Os arrangements. Ba{sub 2}BOsO{sub 6} (B=Sc, Y, In) show antiferromagnetic transitions at 93 K, 69 K, and 28 K, respectively. The Weiss-temperatures are −590 K for Ba{sub 2}ScOsO{sub 6}, −571 K for Ba{sub 2}YOsO{sub 6}, and −155 K for Ba{sub 2}InOsO{sub 6}. Sc{sup 3+} and Y{sup 3+} have the open-shell d{sup 0} electronic configuration, while In{sup 3+} has the closed-shell d{sup 10}. This indicates that a d{sup 0} B-typemore » cation induces stronger overall magnetic exchange interactions in comparison to a d{sup 10}. Comparison of Ba{sub 2}BOsO{sub 6} (B=Sc, Y, In) to their Sr and Ca analogues shows that the structural distortions weaken the overall magnetic exchange interactions. - Graphical abstract: Magnetic properties of osmium double perovskites Ba{sub 2}BOsO{sub 6} (B=Sc, Y, In) were studied. Comparison of Ba{sub 2}BOsO{sub 6}indicates that a d{sup 0} B-type cation induces stronger overall magnetic exchange interactions in comparison to a d{sup 10}. - Highlights: • Magnetic properties of double perovskites Ba{sub 2}BOsO{sub 6} (B=Sc, Y, In) were studied. • A d{sup 0}B-type cation induces stronger magnetic interactions than a d{sup 10}. • Structural distortions weaken the overall Os{sup 5+}-Os{sup 5+} magnetic interactions.« less

Density-dependent regulation of growth of BSC-1 cells in cell culture: Control of growth by low molecular weight nutrients

PubMed Central

Holley, Robert W.; Armour, Rosemary; Baldwin, Julia H.

1978-01-01

BSC-1 cells, epithelial cells of African green monkey kidney origin, show pronounced density-dependent regulation of growth in cell culture. Growth of the cells is rapid to a density of approximately 1.5 × 105 cells/per cm2 in Dulbecco-modified Eagle's medium supplemented with 10% calf serum. Above this “saturation density,” growth is much slower. It has been found that the glucose concentration in the culture medium is important in determining the “saturation density.” If the glucose concentration is increased 4-fold, the “saturation density” increases approximately 50%. Reduction of the “saturation density” of BSC-1 cells is also possible by decreasing the concentrations of low molecular weight nutrients in the culture medium. In medium supplemented with 0.1% calf serum, decreasing the concentrations of all of the organic constituents of the medium, from the high levels present in Dulbecco-modified Eagle's medium to concentrations near physiological levels, decreases the “saturation density” by approximately half. The decreased “saturation density” is not the result of lowering the concentration of any single nutrient but rather results from reduction of the concentrations of several nutrients. When the growth of BSC-1 cells is limited by low concentrations of all of the nutrients, some stimulation of growth results from increasing, separately, the concentrations of individual groups of nutrients, but the best growth stimulation is obtained by increasing the concentrations of all of the nutrients. The “wound healing” phenomenon, one manifestation of density-dependent regulation of growth in cell culture, is abolished by lowering the concentration of glutamine in the medium. Density-dependent regulation of growth of BSC-1 cells in cell culture thus appears to be a complex phenomenon that involves an interaction of nutrient concentrations with other regulatory factors. PMID:272650

Evidence for micronutrient limitation of biological soil crusts: Importance to arid-lands restoration

USGS Publications Warehouse

Bowker, M.A.; Belnap, J.; Davidson, D.W.; Phillips, S.L.

2005-01-01

Desertification is a global problem, costly to national economies and human societies. Restoration of biological soil crusts (BSCs) may have an important role to play in the reversal of desertification due to their ability to decrease erosion and enhance soil fertility. To determine if there is evidence that lower fertility may hinder BSC recolonization, we investigated the hypothesis that BSC abundance is driven by soil nutrient concentrations. At a regional scale (north and central Colorado Plateau, USA), moss and lichen cover and richness are correlated with a complex water-nutrient availability gradient and have approximately six-fold higher cover and approximately two-fold higher species richness on sandy soils than on shale-derived soils. At a microscale, mosses and lichens are overrepresented in microhabitats under the north sides of shrub canopies, where water and nutrients are more available. At two spatial scales, and at the individual species and community levels, our data are consistent with the hypothesis that distributions of BSC organisms are determined largely by soil fertility. The micronutrients Mn and Zn figured prominently and consistently in the various analyses, strongly suggesting that these elements are previously unstudied limiting factors in BSC development. Structural-equation modeling of our data is most consistent with the hypothesis of causal relationships between the availability of micronutrients and the abundance of the two major nitrogen (N) fixers of BSCs. Specifically, higher Mn availability may determine greater Collema tenax abundance, and both Mn and Zn may limit Collema coccophorum; alternative causal hypotheses were less consistent with the data. We propose experimental trials of micronutrient addition to promote the restoration of BSC function on disturbed lands. Arid lands, where BSCs are most prevalent, cover ???40% of the terrestrial surface of the earth; thus the information gathered in this study is potentially useful in many places worldwide. ?? 2005 by the Ecological Society of America.

Measurement of low‐energy backscatter factors using GAFCHROMIC film and OSLDs

PubMed Central

Elson, Howard R.; Lamba, Michael A. S.

2012-01-01

Some of the lowest voltages used in radiotherapy are termed Grenz and superficial X‐rays of ~ 20 and ~ 100 kVp, respectively. Dosimetrically, the surface doses from these beams are calculated with the use of a free in‐air air kerma measurement combined with a backscatter factor and the appropriate ratio of mass energy absorption coefficients from the measurement material to water. Alternative tools to the standard ion chamber for measuring the BSF are GAFCHROMIC EBT2 film and optically stimulated luminescent dosimeter (OSLD) crystals made from Al2O3. The scope of this project included making three different backscatter measurements with an Xstrahl‐D3100 X‐ray unit on the Grenz ray and superficial settings. These measurements were with OSLDs, GAFCHROMIC EBT2 film, and a PTW ionization chamber. The varied measurement methods allowed for intercomparison to determine the accuracy of the results. The ion chamber measurement was the least accurate, as expected from previous experimental findings. GAFCHROMIC EBT2 film proved to be a useful tool which gave reasonable results, and Landauer OSLDs showed good results for smaller field sizes and an increasing overresponse with larger fields. The specific backscatter factors for this machine demonstrated values about 5% higher than the universal values suggested by the AAPM and IPEMB codes of practice for the 100 kVp setting. The 20 kvp measured data from both techniques showed general agreement with those found in the BJR Supplement No. 10, indicating that this unit's Grenz ray spectrum is similar to those used in previous experimental work. PACS number: 87.53.Bn PMID:23149776

Revised ocean backscatter models at C and Ku band under high-wind conditions

NASA Astrophysics Data System (ADS)

Donnelly, William J.; Carswell, James R.; McIntosh, Robert E.; Chang, Paul S.; Wilkerson, John; Marks, Frank; Black, Peter G.

1999-05-01

A series of airborne scatterometer experiments designed to collect C and Ku band ocean backscatter data in regions of high ocean surface winds has recently been completed. More than 100 hours of data were collected using the University of Massachusetts C and Ku band scatterometers, CSCAT and KUSCAT. These instruments measure the full azimuthal normalized radar cross section (NRCS) of a common surface area of the ocean simultaneously at four incidence angles. Our results demonstrate limitations of the current empirical models, C band geophysical model function 4 (CMOD4), SeaSat scatterometer 2 (SASS 2), and NASA scatterometer 1 (NSCAT) 1, that relate ocean backscatter to the near-surface wind at high wind speeds. The discussion focuses on winds in excess of 15 m s-1 in clear atmospheric conditions. The scatterometer data are collocated with measurements from ocean data buoys and Global Positioning System dropsondes, and a Fourier analysis is performed as a function of wind regime. A three-term Fourier series is fit to the backscatter data, and a revised set of coefficients is tabulated. These revised models, CMOD4HW and KUSCAT 1, are the basis for a discussion of the NRCS at high wind speeds. Our scatterometer data show a clear overprediction of the derived NRCS response to high winds based on the CMOD4, SASS 2, and NSCAT 1 models. Furthermore, saturation of the NRCS response begins to occur above 15 m s-1. Sensitivity of the upwind and crosswind response is discussed with implications toward high wind speed retrieval.

The F-16 Onboard Oxygen Generating System: Performance Evaluation and Man Rating

DTIC Science & Technology

1983-08-01

OXYGEN GENERATING , YSTEM: PERFORMANCE EVALUATION AND MAN RATING Thomas C. Horch , Captain, USAF Richard L. Miller, Ph.D. John B. Bomar, Jr...C. Horch , Capt, USAF; R. L. Miller, 8. CONTRACT OR GRANT NUMBER(i) Ph.D.; J. B. Bomar, Jr., Lt Col, IJSAF, BSC; J. B. Tedor, Maj, USAF, BSC; R. D...limitation (as of 1983); however, the information may no longer need protection since it is 14 years. At the time of its publication, Capt Thomas Horch

Monitoring flooding and vegetation on seasonally inundated floodplains with multifrequency polarimetric synthetic aperture radar

NASA Astrophysics Data System (ADS)

Hess, Laura Lorraine

The ability of synthetic aperture radar to detect flooding and vegetation structure was evaluated for three seasonally inundated floodplain sites supporting a broad variety of wetland and upland vegetation types: two reaches of the Solimoes floodplain in the central Amazon, and the Magela Creek floodplain in Northern Territory, Australia. For each site, C- and L-band polarimetric Shuttle Imaging Radar-C (SIR-C) data was obtained at both high- and low-water stages. Inundation status and vegetation structure were documented simultaneous with the SIR-C acquisitions using low-altitude videography and ground measurements. SIR-C images were classified into cover states defined by vegetation physiognomy and presence of standing water, using a decision-tree model with backscattering coefficients at HH, VV, and HV polarizations as input variables. Classification accuracy was assessed using user's accuracy, producer's accuracy, and kappa coefficient for a test population of pixels. At all sites, both C- and L-band were necessary to accurately classify cover types with two dates. HH polarization was most. useful for distinguishing flooded from non-flooded vegetation (C-HH for macrophyte versus pasture, L-HH for flooded versus non-flooded forest), and cross-polarized L-band data provided the best separation between woody and non-woody vegetation. Increases in L-HH backscattering due to flooding were on the order of 3--4 dB for closed-canopy varzea and igapo forest, and 4--7 dB, for open Melaleuca woodland. The broad range of physiognomies and stand structures found in both herbaceous and woody wetland communities, combined with the variation in the amount of emergent canopy caused by water level fluctuations and phenologic changes, resulted in a large range in backscattering characteristics of wetland communities both within and between sites. High accuracies cannot be achieved for these communities using single-date, single-band, single-polarization data, particularly in the case of distinguishing flooded macrophyte from non-flooded forest vegetation. However, the large changes in backscattering caused by flooding make it possible to achieve good accuracies (>85%) using multi-temporal data. Where river stage records are available, SAR-based maps of inundation status on a series of dates can be linked to long-term stage data to define wetland habitat types based on flooding regime and low-water vegetation cover.

Retrievals of Profiles of Fine And Coarse Aerosols Using Lidar And Radiometric Space Measurements

NASA Technical Reports Server (NTRS)

Kaufman, Yoram; Tanre, Didier; Leon, Jean-Francois; Pelon, Jacques; Lau, William K. M. (Technical Monitor)

2002-01-01

In couple of years we expect the launch of the CALIPSO lidar spaceborne mission designed to observe aerosols and clouds. CALIPSO will collect profiles of the lidar attenuated backscattering coefficients in two spectral wavelengths (0.53 and 1.06 microns). Observations are provided along the track of the satellite around the globe from pole to pole. The attenuated backscattering coefficients are sensitive to the vertical distribution of aerosol particles, their shape and size. However the information is insufficient to be mapped into unique aerosol physical properties and vertical distribution. Infinite number of physical solutions can reconstruct the same two wavelength backscattered profile measured from space. CALIPSO will fly in formation with the Aqua satellite and the MODIS spectro-radiometer on board. Spectral radiances measured by MODIS in six channels between 0.55 and 2.13 microns simultaneously with the CALIPSO observations can constrain the solutions and resolve this ambiguity, albeit under some assumptions. In this paper we describe the inversion method and apply it to aircraft lidar and MODIS data collected over a dust storm off the coast of West Africa during the SHADE experiment. It is shown that the product of the single scattering albedo, omega, and the phase function, P, for backscattering can be retrieved from the synergism between measurements avoiding a priori hypotheses required for inverting lidar measurements alone. The resultant value of (omega)P(180 deg.) = 0.016/sr are significantly different from what is expected using Mie theory, but are in good agreement with recent results obtained from lidar observations of dust episodes. The inversion is robust in the presence of noise of 10% and 20% in the lidar signal in the 0.53 and 1.06 pm channels respectively. Calibration errors of the lidar of 5 to 10% can cause an error in optical thickness of 20 to 40% respectively in the tested cases. The lidar calibration errors cause degradation in the ability to fit the MODIS data. Therefore the MODIS measurements can be used to identify the calibration problem and correct for it. The CALIPSO-MODIS measurements of the profiles of fine and coarse aerosols, together with CALIPSO measurements of clouds vertical distribution, is expected to be critically important in understanding aerosol transport across continents and political boundaries, and to study aerosol-cloud interaction and its effect on precipitation and global forcing of climate.

Detection and recognition of targets by using signal polarization properties

NASA Astrophysics Data System (ADS)

Ponomaryov, Volodymyr I.; Peralta-Fabi, Ricardo; Popov, Anatoly V.; Babakov, Mikhail F.

1999-08-01

The quality of radar target recognition can be enhanced by exploiting its polarization signatures. A specialized X-band polarimetric radar was used for target recognition in experimental investigations. The following polarization characteristics connected to the object geometrical properties were investigated: the amplitudes of the polarization matrix elements; an anisotropy coefficient; depolarization coefficient; asymmetry coefficient; the energy of a backscattering signal; object shape factor. A large quantity of polarimetric radar data was measured and processed to form a database of different object and different weather conditions. The histograms of polarization signatures were approximated by a Nakagami distribution, then used for real- time target recognition. The Neyman-Pearson criterion was used for the target detection, and the criterion of the maximum of a posterior probability was used for recognition problem. Some results of experimental verification of pattern recognition and detection of objects with different electrophysical and geometrical characteristics urban in clutter are presented in this paper.

The Estimation of Surface Latent Heat Flux over the Ocean and its Relationship to Marine Atmospheric Boundary Layer (MABL) Structure

NASA Technical Reports Server (NTRS)

Palm, Stephen P.; Schwemmer, Geary K.; Vandemark, Doug; Evans, Keith; Miller, David O.; Demoz, Belay B.; Starr, David OC. (Technical Monitor)

2001-01-01

A new technique combining active and passive remote sensing instruments for the estimation of surface latent heat flux over the ocean is presented. This synergistic method utilizes aerosol lidar backscatter data, multi-channel infrared radiometer data, and microwave scatterometer data acquired onboard the NASA P-313 research aircraft during an extended field campaign over the Atlantic ocean in support of the Lidar In-space Technology Experiment (LITE) in September of 1994. The 10 meter wind speed derived from scatterometers and lidar-radiometer inferred near-surface moisture are used to obtain an estimate of the surface flux of moisture via a bulk aerodynamic formula. The results are compared with the Special Sensor Microwave Imager (SSM/I) daily average latent heat flux and show reasonable agreement. However, the SSM/I values are biased low by about 15 W/sq m. In addition, the Marine Atmospheric Boundary Layer (MABL) height, entrainment zone thickness and integrated lidar backscatter intensity are computed from the lidar data and compared with the magnitude of the surface fluxes. The results show that the surface latent heat flux is most strongly correlated with entrainment zone depth, MABL height and the integrated MABL lidar backscatter, with corresponding correlation coefficients of 0.39, 0.43 and 0.71, respectively.

Axisymmetric scattering of an acoustical Bessel beam by a rigid fixed spheroid.

PubMed

Mitri, Farid G

2015-10-01

Based on the partial-wave series expansion (PWSE) method in spherical coordinates, a formal analytical solution for the acoustic scattering of a zeroth-order Bessel acoustic beam centered on a rigid fixed (oblate or prolate) spheroid is provided. The unknown scattering coefficients of the spheroid are determined by solving a system of linear equations derived for the Neumann boundary condition. Numerical results for the modulus of the backscattered pressure (θ = π) in the near field and the backscattering form function in the far field for both prolate and oblate spheroids are presented and discussed, with particular emphasis on the aspect ratio (i.e., the ratio of the major axis over the minor axis of the spheroid), the half-cone angle of the Bessel beam, and the dimensionless frequency. The plots display periodic oscillations (versus the dimensionless frequency) because of the interference of specularly reflected waves in the backscattering direction with circumferential Franz' waves circumnavigating the surface of the spheroid in the surrounding fluid. Moreover, the 3-D directivity patterns illustrate the near- and far-field axisymmetric scattering. Investigations in underwater acoustics, particle levitation, scattering, and the detection of submerged elongated objects and other related applications utilizing Bessel waves would benefit from the results of the present study.

The Estimation of Surface Latent Heat Flux Over the Ocean and its Relationship to Marine Atmospheric Boundary Layer (MABL) Structure

NASA Technical Reports Server (NTRS)

Palm, Stephen P.; Miller, David O.; Schwemmer, Geary

2000-01-01

A new technique combining active and passive remote sensing instruments for the estimation of surface latent heat flux over the ocean is presented. This synergistic method uses aerosol lidar backscatter data, multi-channel infrared radiometer data and microwave scatterometer data acquired onboard the NASA P-3B research aircraft during an extended field campaign over the Atlantic ocean in support of the Lidar In-space Technology Experiment (LITE) in September of 1994. The 10 meter wind speed derived from the scatterometers and the lidar-radiometer inferred near-surface moisture are used to obtain an estimate of the surface flux of moisture via bulk aerodynamic formulae. The results are compared with the Special Sensor Microwave Imager (SSM/I) daily average latent heat flux and show reasonable agreement with an rms error and bias of about 50 and 25 W per square meters, respectively. In addition, the MABL height, entrainment zone thickness and integrated lidar backscatter intensity are computed from the lidar data and compared with the magnitude of the surface fluxes. The results show that the surface latent heat flux is most strongly correlated with entrainment zone top, bottom and the integrated MABL lidar backscatter, with corresponding correlation coefficients of 0.62, 0.67 and 0.61, respectively.

Analyses of scattering characteristics of chosen anthropogenic aerosols

NASA Astrophysics Data System (ADS)

Kaszczuk, Miroslawa; Mierczyk, Zygmunt; Muzal, Michal

2008-10-01

In the work, analyses of scattering profile of chosen anthropogenic aerosols for two wavelengths (λ1 = 1064 nm and λ2 = 532 nm) were made. As an example of anthropogenic aerosol three different pyrotechnic mixtures (DM11, M2, M16) were taken. Main parameters of smoke particles were firstly analyzed and well described, taking particle shape and size into special consideration. Shape of particles was analyzed on the basis of SEM pictures, and particle size was measured. Participation of particles in each fixed fraction characterized by range of sizes was analyzed and parameters of smoke particles of characteristic sizes and function describing aerosol size distribution (ASD) were determinated. Analyses of scattering profiles were carried out on the basis of both model of scattering on spherical and nonspherical particles. In the case of spherical particles Rayleigh-Mie model was used and for nonspherical particles analyses firstly model of spheroids was used, and then Rayleigh-Mie one. For each characteristic particle one calculated value of four parameters (effective scattering cross section σSCA, effective backscattering cross section σBSCA, scattering efficiency QSCA, backscattering efficiency QBSCA) and value of backscattering coefficient β for whole particles population. Obtained results were compared with the same parameters calculated for natural aerosol (cirrus cloud).

Bio-Optics of the Chesapeake Bay from Measurements and Radiative Transfer Calculations

NASA Technical Reports Server (NTRS)

Tzortziou, Maria; Herman, Jay R.; Gallegos, Charles L.; Neale, Patrick J.; Subramaniam, Ajit; Harding, Lawrence W., Jr.; Ahmad, Ziauddin

2005-01-01

We combined detailed bio-optical measurements and radiative transfer (RT) modeling to perform an optical closure experiment for optically complex and biologically productive Chesapeake Bay waters. We used this experiment to evaluate certain assumptions commonly used when modeling bio-optical processes, and to investigate the relative importance of several optical characteristics needed to accurately model and interpret remote sensing ocean-color observations in these Case 2 waters. Direct measurements were made of the magnitude, variability, and spectral characteristics of backscattering and absorption that are critical for accurate parameterizations in satellite bio-optical algorithms and underwater RT simulations. We found that the ratio of backscattering to total scattering in the mid-mesohaline Chesapeake Bay varied considerably depending on particulate loading, distance from land, and mixing processes, and had an average value of 0.0128 at 530 nm. Incorporating information on the magnitude, variability, and spectral characteristics of particulate backscattering into the RT model, rather than using a volume scattering function commonly assumed for turbid waters, was critical to obtaining agreement between RT calculations and measured radiometric quantities. In situ measurements of absorption coefficients need to be corrected for systematic overestimation due to scattering errors, and this correction commonly employs the assumption that absorption by particulate matter at near infrared wavelengths is zero.

Random fiber laser based on artificially controlled backscattering fibers.

PubMed

Wang, Xiaoliang; Chen, Daru; Li, Haitao; She, Lijuan; Wu, Qiong

2018-01-10

The random fiber laser (RFL), which is a milestone in laser physics and nonlinear optics, has attracted considerable attention recently. Most previously reported RFLs are based on distributed feedback of Rayleigh scattering amplified through the stimulated Raman-Brillouin scattering effect in single-mode fibers, which require long-distance (tens of kilometers) single-mode fibers and high threshold, up to watt level, due to the extremely small Rayleigh scattering coefficient of the fiber. We proposed and demonstrated a half-open-cavity RFL based on a segment of an artificially controlled backscattering single-mode fiber with a length of 210 m, 310 m, or 390 m. A fiber Bragg grating with a central wavelength of 1530 nm and a segment of artificially controlled backscattering single-mode fiber fabricated by using a femtosecond laser form the half-open cavity. The proposed RFL achieves thresholds of 25 mW, 30 mW, and 30 mW, respectively. Random lasing at a wavelength of 1530 nm and extinction ratio of 50 dB is achieved when a segment of 5 m erbium-doped fiber is pumped by a 980 nm laser diode in the RFL. A novel RFL with many short cavities has been achieved with low threshold.

Observations of stratospheric aerosols associated with the El Chichon eruption

NASA Technical Reports Server (NTRS)

Thomas, L.; Vaughan, G.; Jenkins, D. B.; Wareing, D.; Farrington, M.

1986-01-01

Lidar observations of aerosols were carried out at Aberystwyth between Nov. 1982 and Dec. 1985 using a frequency doubled and frequency tripled Nd/Yag laser and a receiver incorporating a 1 m diameter in a Newtonian telescope configuration. In analyses of the experimental data attention is paid to the magnitude of the coefficient relating extinction and backscatter, the choice being related to the possible presence of aerosols in the upper troposphere and the atmospheric densities employed in the normalisation procedure. The aerosol loading showed marked day to day changes in early months and an overall decay was apparent only after April 1983, this decay being consistent with an e sup -1 time of about 7 months. The general decay was accompanied by a lowering of the layer but layers of aerosols were shown intermittently at heights above the main layer in winter months. The height variations of photon counts corrected for range, or of aerosol backscatter ratio, showed clear signatures of the tropopause. A strong correlation was found between the heights of the tropopause identified from the lidar measurements and from radiosonde-borne temperature measurements. A notable feature of the observations is the appearance of very sharp height gradients of backscatter ratio which seem to be produced by differential advection.

A chronicle of BScN honours/ non-honours outcomes and experiences post-graduation.

PubMed

Gillis, Angela

2007-01-01

This paper reports on a graduate follow-up of the outcomes of participation in an honours BScN program, two to seven years post-graduation. It compares two groups of graduates with high GPA scores, both initially eligible to complete the honours program. One group completed the honours program; the other group completed the regular BScN program. In phase 1 of the study, a self-administered mailed questionnaire was sent to participants to assess their involvement in research activities, occupancy of leadership positions, enrollment in graduate studies and demonstration of liberal education competencies in their professional lives after graduation. In phase two, personal interviews were held with a purposive subsample of participants to explore early career workplace experiences with research-based activities and participants' perceptions of factors influencing their decision to complete or not to complete the honours program. Graduates with high GPA scores from both programs demonstrated expected professional outcomes post-graduation. Follow up at 10-12 years post-graduation and replication with larger samples are recommended.

Assessment of Barriers to Essential Surgical Care in Two Communities in the Upper West Region, Ghana.

PubMed

Gyedu, Adam; Boakye, Godfred; Dally, Charles K; Agbeko, Anita Eseenam; Abantanga, Francis A; Kushner, Adam L; Stewart, Barclay T

2017-01-01

Systematic assessments of individual-and community-level barriers to surgical care (BSC) in low-and middle-income countries that might inform potential interventions are lacking. We used a novel tool to assess BSC systematically during a surgical outreach in two communities in Upper West region, Ghana. Results were scored in three dimensions of barriers to care (acceptability, affordability, and accessibility); higher dimension scores signified less salient barriers. A total index out of 10 was derived. In total, 169 individuals participated in Nadowli (68, 40%) and in Nandom (101, 60%). Nadowli had fewer BSC than Nandom (median index 7.8 vs 7.2; p < .001). Dimension scores ranged from 10.8 to 14.5 out of 18 points. Fear or mistrust of surgical care and stigma were reported more frequently in Nandom (p < .001). Reported barriers were not always the same in each community. Systematically defining barriers to essential surgical care provides an opportunity for planning targeted interventions at the community-level.

Foldability of a Natural De Novo Evolved Protein.

PubMed

Bungard, Dixie; Copple, Jacob S; Yan, Jing; Chhun, Jimmy J; Kumirov, Vlad K; Foy, Scott G; Masel, Joanna; Wysocki, Vicki H; Cordes, Matthew H J

2017-11-07

The de novo evolution of protein-coding genes from noncoding DNA is emerging as a source of molecular innovation in biology. Studies of random sequence libraries, however, suggest that young de novo proteins will not fold into compact, specific structures typical of native globular proteins. Here we show that Bsc4, a functional, natural de novo protein encoded by a gene that evolved recently from noncoding DNA in the yeast S. cerevisiae, folds to a partially specific three-dimensional structure. Bsc4 forms soluble, compact oligomers with high β sheet content and a hydrophobic core, and undergoes cooperative, reversible denaturation. Bsc4 lacks a specific quaternary state, however, existing instead as a continuous distribution of oligomer sizes, and binds dyes indicative of amyloid oligomers or molten globules. The combination of native-like and non-native-like properties suggests a rudimentary fold that could potentially act as a functional intermediate in the emergence of new folded proteins de novo. Copyright © 2017 Elsevier Ltd. All rights reserved.

Signature of Arctic first-year ice melt pond fraction in X-band SAR imagery

NASA Astrophysics Data System (ADS)

Fors, Ane S.; Divine, Dmitry V.; Doulgeris, Anthony P.; Renner, Angelika H. H.; Gerland, Sebastian

2017-03-01

In this paper we investigate the potential of melt pond fraction retrieval from X-band polarimetric synthetic aperture radar (SAR) on drifting first-year sea ice. Melt pond fractions retrieved from a helicopter-borne camera system were compared to polarimetric features extracted from four dual-polarimetric X-band SAR scenes, revealing significant relationships. The correlations were strongly dependent on wind speed and SAR incidence angle. Co-polarisation ratio was found to be the most promising SAR feature for melt pond fraction estimation at intermediate wind speeds (6. 2 m s-1), with a Spearman's correlation coefficient of 0. 46. At low wind speeds (0. 6 m s-1), this relation disappeared due to low backscatter from the melt ponds, and backscatter VV-polarisation intensity had the strongest relationship to melt pond fraction with a correlation coefficient of -0. 53. To further investigate these relations, regression fits were made both for the intermediate (R2fit = 0. 21) and low (R2fit = 0. 26) wind case, and the fits were tested on the satellite scenes in the study. The regression fits gave good estimates of mean melt pond fraction for the full satellite scenes, with less than 4 % from a similar statistics derived from analysis of low-altitude imagery captured during helicopter ice-survey flights in the study area. A smoothing window of 51 × 51 pixels gave the best reproduction of the width of the melt pond fraction distribution. A considerable part of the backscatter signal was below the noise floor at SAR incidence angles above ˜ 40°, restricting the information gain from polarimetric features above this threshold. Compared to previous studies in C-band, limitations concerning wind speed and noise floor set stricter constraints on melt pond fraction retrieval in X-band. Despite this, our findings suggest new possibilities in melt pond fraction estimation from X-band SAR, opening for expanded monitoring of melt ponds during melt season in the future.

Towards Linking 3D SAR and Lidar Models with a Spatially Explicit Individual Based Forest Model

NASA Astrophysics Data System (ADS)

Osmanoglu, B.; Ranson, J.; Sun, G.; Armstrong, A. H.; Fischer, R.; Huth, A.

2017-12-01

In this study, we present a parameterization of the FORMIND individual-based gap model (IBGM)for old growth Atlantic lowland rainforest in La Selva, Costa Rica for the purpose of informing multisensor remote sensing techniques for above ground biomass techniques. The model was successfully parameterized and calibrated for the study site; results show that the simulated forest reproduces the structural complexity of Costa Rican rainforest based on comparisons with CARBONO inventory plot data. Though the simulated stem numbers (378) slightly underestimated the plot data (418), particularly for canopy dominant intermediate shade tolerant trees and shade tolerant understory trees, overall there was a 9.7% difference. Aboveground biomass (kg/ha) showed a 0.1% difference between the simulated forest and inventory plot dataset. The Costa Rica FORMIND simulation was then used to parameterize a spatially explicit (3D) SAR and lidar backscatter models. The simulated forest stands were used to generate a Look Up Table as a tractable means to estimate aboveground forest biomass for these complex forests. Various combinations of lidar and radar variables were evaluated in the LUT inversion. To test the capability of future data for estimation of forest height and biomass, we considered data of 1) L- (or P-) band polarimetric data (backscattering coefficients of HH, HV and VV); 2) L-band dual-pol repeat-pass InSAR data (HH/HV backscattering coefficients and coherences, height of scattering phase center at HH and HV using DEM or surface height from lidar data as reference); 3) P-band polarimetric InSAR data (canopy height from inversion of PolInSAR data or use the coherences and height of scattering phase center at HH, HV and VV); 4) various height indices from waveform lidar data); and 5) surface and canopy top height from photon-counting lidar data. The methods for parameterizing the remote sensing models with the IBGM and developing Look Up Tables will be discussed. Results from various remote sensing scenarios will also be presented.

Multi-Feature Classification of Multi-Sensor Satellite Imagery Based on Dual-Polarimetric Sentinel-1A, Landsat-8 OLI, and Hyperion Images for Urban Land-Cover Classification.

PubMed

Zhou, Tao; Li, Zhaofu; Pan, Jianjun

2018-01-27

This paper focuses on evaluating the ability and contribution of using backscatter intensity, texture, coherence, and color features extracted from Sentinel-1A data for urban land cover classification and comparing different multi-sensor land cover mapping methods to improve classification accuracy. Both Landsat-8 OLI and Hyperion images were also acquired, in combination with Sentinel-1A data, to explore the potential of different multi-sensor urban land cover mapping methods to improve classification accuracy. The classification was performed using a random forest (RF) method. The results showed that the optimal window size of the combination of all texture features was 9 × 9, and the optimal window size was different for each individual texture feature. For the four different feature types, the texture features contributed the most to the classification, followed by the coherence and backscatter intensity features; and the color features had the least impact on the urban land cover classification. Satisfactory classification results can be obtained using only the combination of texture and coherence features, with an overall accuracy up to 91.55% and a kappa coefficient up to 0.8935, respectively. Among all combinations of Sentinel-1A-derived features, the combination of the four features had the best classification result. Multi-sensor urban land cover mapping obtained higher classification accuracy. The combination of Sentinel-1A and Hyperion data achieved higher classification accuracy compared to the combination of Sentinel-1A and Landsat-8 OLI images, with an overall accuracy of up to 99.12% and a kappa coefficient up to 0.9889. When Sentinel-1A data was added to Hyperion images, the overall accuracy and kappa coefficient were increased by 4.01% and 0.0519, respectively.

The interplay of species concepts, taxonomy, and conservation: lessons from the Hawaiian avifauna

USGS Publications Warehouse

Pratt, H. Douglas; Pratt, Thane K.

2001-01-01

The Hawaiian Islands, with their unique geological history and geographic position, provide an excellent natural laboratory in which to evaluate currently competing biological (BSC) and phylogenetic (PSC) concepts of the species. Although the BSC as historically applied in archipelagic situations is shown to be flawed in producing overlumped polytypic species, it nevertheless remains the preferable concept for most practical purposes. A review of the taxonomic history and species limits in Hawaiian birds under both concepts reveals that, when properly applied, the BSC yields a species total remarkably close to that produced under the PSC, contrary to what many proponents of the latter have supposed. We propose that the widespread adoption of the PSC for conservation purposes is potentially harmful. The PSC trivializes the species taxon and introduces new problems of deciding when a population becomes diagnosable, the possibility that species could appear and disappear in a reticulate fashion, and the likelihood that genetically diagnosable but phenotypically identical, and therefore not field identifiable, populations could be ranked as species. All of these problems negatively impact such things as constructing credible and politically defensible lists of endangered species, the prioritization of limited conservation resources, and the gathering of field data. We contend the BSC is arguably a more rational concept that better supports the activities of both scientific and nonprofessional observers. Biological species limits in oceanic archipelagoes worldwide need to be reevaluated using modern concepts and technologies before rational conservation decisions can be made.

Coherent optical determination of the leaf angle distribution of corn

NASA Technical Reports Server (NTRS)

Ulaby, F. T. (Principal Investigator); Pihlman, M.

1981-01-01

A coherent optical technique for the diffraction analysis of an image is presented. Developments in radar remote sensing shows a need to understand plant geometry and its relationship to plant moisture, soil moisture, and the radar backscattering coefficient. A corn plant changes its leaf angle distribution, as a function of time, from a uniform distribution to one that is strongly vertical. It is shown that plant and soil moisture may have an effect on plant geometry.

Lidar stand-alone retrieval of atmospheric aerosol microphysical properties during SLOPE

NASA Astrophysics Data System (ADS)

Ortiz-Amezcua, Pablo; Samaras, Stefanos; Böckmann, Christine; Antonio Benavent-Oltra, Jose; Luis Guerrero-Rascado, Juan; Román, Roberto; Alados-Arboledas, Lucas

2018-04-01

Two cases from SLOPE campaign at Granada are analyzed in terms of particle microphysical properties using novel software developed at Potsdam University. Multiwavelength Raman lidar measurements of particle extinction and backscatter coefficients as well as linear particle depolarization ratios are used as input for the software. The result of the retrieval is a 2-dimensional particle volume distribution as a function of radius and aspect ratio, from which the particle microphysical properties are obtained.

Measurement and Study of Lidar Ratio by Using a Raman Lidar in Central China.

PubMed

Wang, Wei; Gong, Wei; Mao, Feiyue; Pan, Zengxin; Liu, Boming

2016-05-18

We comprehensively evaluated particle lidar ratios (i.e., particle extinction to backscatter ratio) at 532 nm over Wuhan in Central China by using a Raman lidar from July 2013 to May 2015. We utilized the Raman lidar data to obtain homogeneous aerosol lidar ratios near the surface through the Raman method during no-rain nights. The lidar ratios were approximately 57 ± 7 sr, 50 ± 5 sr, and 22 ± 4 sr under the three cases with obviously different pollution levels. The haze layer below 1.8 km has a large particle extinction coefficient (from 5.4e-4 m(-1) to 1.6e-4 m(-1)) and particle backscatter coefficient (between 1.1e-05 m(-1)sr(-1) and 1.7e-06 m(-1)sr(-1)) in the heavily polluted case. Furthermore, the particle lidar ratios varied according to season, especially between winter (57 ± 13 sr) and summer (33 ± 10 sr). The seasonal variation in lidar ratios at Wuhan suggests that the East Asian monsoon significantly affects the primary aerosol types and aerosol optical properties in this region. The relationships between particle lidar ratios and wind indicate that large lidar ratio values correspond well with weak winds and strong northerly winds, whereas significantly low lidar ratio values are associated with prevailing southwesterly and southerly wind.

Measurement and Study of Lidar Ratio by Using a Raman Lidar in Central China

PubMed Central

Wang, Wei; Gong, Wei; Mao, Feiyue; Pan, Zengxin; Liu, Boming

2016-01-01

We comprehensively evaluated particle lidar ratios (i.e., particle extinction to backscatter ratio) at 532 nm over Wuhan in Central China by using a Raman lidar from July 2013 to May 2015. We utilized the Raman lidar data to obtain homogeneous aerosol lidar ratios near the surface through the Raman method during no-rain nights. The lidar ratios were approximately 57 ± 7 sr, 50 ± 5 sr, and 22 ± 4 sr under the three cases with obviously different pollution levels. The haze layer below 1.8 km has a large particle extinction coefficient (from 5.4e-4 m−1 to 1.6e-4 m−1) and particle backscatter coefficient (between 1.1e-05 m−1sr−1 and 1.7e-06 m−1sr−1) in the heavily polluted case. Furthermore, the particle lidar ratios varied according to season, especially between winter (57 ± 13 sr) and summer (33 ± 10 sr). The seasonal variation in lidar ratios at Wuhan suggests that the East Asian monsoon significantly affects the primary aerosol types and aerosol optical properties in this region. The relationships between particle lidar ratios and wind indicate that large lidar ratio values correspond well with weak winds and strong northerly winds, whereas significantly low lidar ratio values are associated with prevailing southwesterly and southerly wind. PMID:27213414

A Model with Ellipsoidal Scatterers for Polarimetric Remote Sensing of Anisotropic Layered Media

NASA Technical Reports Server (NTRS)

Nghiem, S. V.; Kwok, R.; Kong, J. A.; Shin, R. T.

1993-01-01

This paper presents a model with ellipsoidal scatterers for applications to polarimetric remote sensing of anisotropic layered media at microwave frequencies. The physical configuration includes an isotropic layer covering an anisotropic layer above a homogeneous half space. The isotropic layer consists of randomly oriented spheroids. The anisotropic layer contains ellipsoidal scatterers with a preferential vertical alignment and random azimuthal orientations. Effective permittivities of the scattering media are calculated with the strong fluctuation theory extended to account for the nonspherical shapes and the scatterer orientation distributions. On the basis of the analytic wave theory, dyadic Green's functions for layered media are used to derive polarimetric backscattering coefficients under the distorted Born approximation. The ellipsoidal shape of the scatterers gives rise to nonzero cross-polarized returns from the untilted anisotropic medium in the first-order approximation. Effects of rough interfaces are estimated by an incoherent addition method. Theoretical results and experimental data are matched at 9 GHz for thick first-year sea ice with a bare surface and with a snow cover at Point Barrow, Alaska. The model is then used to study the sensitivity of polarimetric backscattering coefficients with respect to correlation lengths representing the geometry of brine inclusions. Polarimetric signatures of bare and snow-covered sea ice are also simulated based on the model to investigate effects of different scattering mechanisms.

A comparison of lidar inversion methods for cirrus applications

NASA Technical Reports Server (NTRS)

Elouragini, Salem; Flamant, Pierre H.

1992-01-01

Several methods for inverting the lidar equation are suggested as means to derive the cirrus optical properties (beta backscatter, alpha extinction coefficients, and delta optical depth) at one wavelength. The lidar equation can be inverted in a linear or logarithmic form; either solution assumes a linear relationship: beta = kappa(alpha), where kappa is the lidar ratio. A number of problems prevent us from calculating alpha (or beta) with a good accuracy. Some of these are as follows: (1) the multiple scattering effect (most authors neglect it); (2) an absolute calibration of the lidar system (difficult and sometimes not possible); (3) lack of accuracy on the lidar ratio k (taken as constant, but in fact it varies with range and cloud species); and (4) the determination of boundary condition for logarithmic solution which depends on signal to noise ration (SNR) at cloud top. An inversion in a linear form needs an absolute calibration of the system. In practice one uses molecular backscattering below the cloud to calibrate the system. This method is not permanent because the lower atmosphere turbidity is variable. For a logarithmic solution, a reference extinction coefficient (alpha(sub f)) at cloud top is required. Several methods to determine alpha(sub f) were suggested. We tested these methods at low SNR. This led us to propose two new methods referenced as S1 and S2.

Microwave scattering and emission from a half-space anisotropic random medium

NASA Astrophysics Data System (ADS)

Mudaliar, Saba; Lee, Jay Kyoon

1990-12-01

This paper is a sequel to an earlier paper (Lee and Mudaliar, 1988) where the backscattering coefficients of a half-space anisotropic random medium were obtained. Here the bistatic scattering coefficients are calculated by solving the modified radiative transfer equations under a first-order approximation. The effects of multiple scattering on the results are observed. Emissivities are calculated and compared with those obtained using the Born approximation (single scattering). Several interesting properties of the model are brought to notice using numerical examples. Finally, as an application, the theory is used to interpret the passive remote sensing data of multiyear sea ice in the microwave frequency range. A quite close agreement between theoretical prediction and the measured data is found.

Aerosol characteristics inversion based on the improved lidar ratio profile with the ground-based rotational Raman-Mie lidar

NASA Astrophysics Data System (ADS)

Ji, Hongzhu; Zhang, Yinchao; Chen, Siying; Chen, He; Guo, Pan

2018-06-01

An iterative method, based on a derived inverse relationship between atmospheric backscatter coefficient and aerosol lidar ratio, is proposed to invert the lidar ratio profile and aerosol extinction coefficient. The feasibility of this method is investigated theoretically and experimentally. Simulation results show the inversion accuracy of aerosol optical properties for iterative method can be improved in the near-surface aerosol layer and the optical thick layer. Experimentally, as a result of the reduced insufficiency error and incoherence error, the aerosol optical properties with higher accuracy can be obtained in the near-surface region and the region of numerical derivative distortion. In addition, the particle component can be distinguished roughly based on this improved lidar ratio profile.

Laser-based air data system for aircraft control using Raman and elastic backscatter for the measurement of temperature, density, pressure, moisture, and particle backscatter coefficient.

PubMed

Fraczek, Michael; Behrendt, Andreas; Schmitt, Nikolaus

2012-01-10

Flight safety in all weather conditions demands exact and reliable determination of flight-critical air parameters. Air speed, temperature, density, and pressure are essential for aircraft control. Conventional air data systems can be impacted by probe failure caused by mechanical damage from hail, volcanic ash, and icing. While optical air speed measurement methods have been discussed elsewhere, in this paper, a new concept for optically measuring the air temperature, density, pressure, moisture, and particle backscatter is presented, being independent on assumptions on the atmospheric state and eliminating the drawbacks of conventional aircraft probes by providing a different measurement principle. The concept is based on a laser emitting laser pulses into the atmosphere through a window and detecting the signals backscattered from a fixed region just outside the disturbed area of the fuselage flows. With four receiver channels, different spectral portions of the backscattered light are extracted. The measurement principle of air temperature and density is based on extracting two signals out of the rotational Raman (RR) backscatter signal of air molecules. For measuring the water vapor mixing ratio-and thus the density of the moist air-a water vapor Raman channel is included. The fourth channel serves to detect the elastic backscatter signal, which is essential for extending the measurements into clouds. This channel contributes to the detection of aerosols, which is interesting for developing a future volcanic ash warning system for aircraft. Detailed and realistic optimization and performance calculations have been performed based on the parameters of a first prototype of such a measurement system. The impact and correction of systematic error sources, such as solar background at daytime and elastic signal cross talk appearing in optically dense clouds, have been investigated. The results of the simulations show the high potential of the proposed system for reliable operation in different atmospheric conditions. Based on a laser emitting pulses at a wavelength of 532 nm with 200 mJ pulse energy, the expected measurement precisions (1-σ statistical uncertainty) are <0.6 K for temperature, <0.3% for density, and <0.4% for pressure for the detection of a single laser pulse at a flight altitude of 13,000 m at daytime. The errors will be smaller during nighttime or at lower altitudes. Even in optically very dense clouds with backscatter ratios of 10,000 and RR filters suppressing the elastic backscatter by 6 orders of magnitude, total errors of <1.4 K, <0.4%, and <0.9%, are expected, respectively. The calculations show that aerospace accuracy standards will be met with even lower pulse energies of 75 mJ for pressure and 18 mJ for temperature measurements when the backscatter signals of 10 laser pulses are averaged. Using laser sources at 355 nm will lead to a further reduction of the necessary pulse energies by more than a factor of 3. © 2012 Optical Society of America

A cost-effectiveness analysis of first-line induction and maintenance treatment sequences in patients with advanced nonsquamous non-small-cell lung cancer in France

PubMed Central

Taipale, Kaisa; Winfree, Katherine B; Boye, Mark; Basson, Mickael; Sleilaty, Ghassan; Eaton, James; Evans, Rachel; Chouaid, Christos

2017-01-01

Background Comparative effectiveness and cost-effectiveness data for induction–maintenance (I–M) sequences for the treatment of patients with nonsquamous non-small-cell lung cancer (nsqNSCLC) are limited because of a lack of direct evidence. This analysis aimed to compare the cost-effectiveness of I–M pemetrexed with those of other I–M regimens used for the treatment of patients with advanced nsqNSCLC in the French health-care setting. Materials and methods A previously developed global partitioned survival model was adapted to the France-only setting by restricting treatment sequences to include 12 I–M regimens most relevant to France, and incorporating French costs and resource-use data. Following a systematic literature review, network meta-analyses were performed to obtain hazard ratios for progression-free survival (PFS) and overall survival (OS) relative to gemcitabine + cisplatin (induction sequences) or best supportive care (BSC) (maintenance sequences). Modeled health-care benefits were expressed as life-years (LYs) and quality-adjusted LYs (QALYs) (estimated using French EuroQol five-dimension questionnaire tariffs). The study was conducted from the payer perspective (National Health Insurance). Cost- and benefit-model inputs were discounted at an annual rate of 4%. Results Base-case results showed pemetrexed + cisplatin induction followed by (→) pemetrexed maintenance had the longest mean OS and PFS and highest LYs and QALYs. Costs ranged from €12,762 for paclitaxel + carboplatin → BSC to €35,617 for pemetrexed + cisplatin → pemetrexed (2015 values). Gemcitabine + cisplatin → BSC, pemetrexed + cisplatin → BSC, and pemetrexed + cisplatin → pemetrexed were associated with fully incremental cost-effectiveness ratios (ICERs) of €16,593, €80,656, and €102,179, respectively, per QALY gained versus paclitaxel + carboplatin → BSC. All other treatment sequences were either dominated (ie, another sequence had lower costs and better/equivalent outcomes) or extendedly dominated (ie, the comparator had a higher ICER than a more effective comparator) in the model. Sensitivity analyses showed the model to be relatively insensitive to plausible changes in the main assumptions, with none increasing or decreasing the ICER by more than ~€20,000 per QALY gained. Conclusion In the absence of direct comparative trial evidence, this cost-effectiveness analysis indicated that of a large number of I–M sequences used for the treatment of patients with nsqNSCLC in France, pemetrexed + cisplatin → pemetrexed achieved the best clinical outcomes (0.28 incremental QALYs gained) versus paclitaxel + carboplatin → BSC. PMID:28860832

Using Balanced Scorecard (BSC) approach to improve ergonomics programs.

PubMed

Fernandes, Marcelo Vicente Forestieri

2012-01-01

The purpose of this paper is to propose foundations for a theory of using the Balanced Scorecard (BSC) methodology to improve the strategic view of ergonomics inside the organizations. This approach may help to promote a better understanding of investing on an ergonomic program to obtain good results in quality and production, as well as health maintenance. It is explained the basics of balanced scorecard, and how ergonomists could use this to work with strategic enterprises demand. Implications of this viewpoint for the development of a new methodology for ergonomics strategy views are offered.

Preparation of a Natural Product Extract Library for Investigation Against Disease States Specific to Defence Health: A Mini Long Range Research Project

DTIC Science & Technology

2009-02-01

Sci in 1994 and with a BSc(Hons) in 1995 from The University of Melbourne. In 1999 he completed a PhD in marine natural products chemistry from the...BSc(Hons) in 1994 from the University of Melbourne. In 1998 she completed a PhD in organic chemistry , developing new free-radical syntheses of some...Melissa began work in the area of medicinal chemistry , developing partial agonists of adenosine A1 receptors; firstly at Deakin University and

Monitoring of biophysical parameters of cashew plants in Cambodia using ALOS/PALSAR data.

PubMed

Avtar, Ram; Takeuchi, Wataru; Sawada, Haruo

2013-02-01

An accurate estimation of a plant's age is required for the prediction of yield and management practices. This study demonstrates the relationship between backscattering properties (σ°) of Phased Array type L-band Synthetic Aperture Radar (PALSAR) dual polarimetric data with cashew plants' biophysical parameters (height, age, crown diameter, diameter at breast height, basal area, tree density, and biomass) in Cambodia. PALSAR σ° has shown a positive correlation with the biophysical parameters of cashew plants. The value of σ° increases with the age of cashew plants. At a young stage, the cashew plants show a higher rate of an increase in σ° compared to that at the mature stage. The σ° horizontal polarization transmitted and vertical received (HV) shows higher sensitivity to the plant's growth than σ° horizontal polarization transmitted and received (HH). High backscattering and low variations were observed at mature stage (8-12 years) of cashew plantation. Saturation in backscattering has shown from the age of about 13 years. The validation results indicate strong coefficient of determination (R(2) = 0.86 and 0.88) for PALSAR-predicted age and biomass of cashew plants with root mean square error = 1.8 years and 16.3 t/ha for age and biomass, respectively. The correlations of σ° (HH) with biophysical parameters observed in the dry season were better than those of the rainy season because soil moisture interferes with backscattering in the rainy season. Biomass accumulation rate of cashew plants has been predicted that would be useful for selection of plants species to enhance carbon sequestration. This study provides an insight to use PALSAR for the monitoring of growth stages of plants at the regional level.

Quantitative RNFL attenuation coefficient measurements by RPE-normalized OCT data

NASA Astrophysics Data System (ADS)

Vermeer, K. A.; van der Schoot, J.; Lemij, H. G.; de Boer, J. F.

2012-03-01

We demonstrate significantly different scattering coefficients of the retinal nerve fiber layer (RNFL) between normal and glaucoma subjects. In clinical care, SD-OCT is routinely used to assess the RNFL thickness for glaucoma management. In this way, the full OCT data set is conveniently reduced to an easy to interpret output, matching results from older (non- OCT) instruments. However, OCT provides more data, such as the signal strength itself, which is due to backscattering in the retinal layers. For quantitative analysis, this signal should be normalized to adjust for local differences in the intensity of the beam that reaches the retina. In this paper, we introduce a model that relates the OCT signal to the attenuation coefficient of the tissue. The average RNFL signal (within an A-line) was then normalized based on the observed RPE signal, resulting in normalized RNFL attenuation coefficient maps. These maps showed local defects matching those found in thickness data. The average (normalized) RNFL attenuation coefficient of a fixed band around the optic nerve head was significantly lower in glaucomatous eyes than in normal eyes (3.0mm-1 vs. 4.9mm-1, P<0.01, Mann-Whitney test).

Preliminary analysis of the sensitivity of AIRSAR images to soil moisture variations

NASA Technical Reports Server (NTRS)

Pardipuram, Rajan; Teng, William L.; Wang, James R.; Engman, Edwin T.

1993-01-01

Synthetic Aperture Radar (SAR) images acquired from various sources such as Shuttle Imaging Radar B (SIR-B) and airborne SAR (AIRSAR) have been analyzed for signatures of soil moisture. The SIR-B measurements have shown a strong correlation between measurements of surface soil moisture (0-5 cm) and the radar backscattering coefficient sigma(sup o). The AIRSAR measurements, however, indicated a lower sensitivity. In this study, an attempt has been made to investigate the causes for this reduced sensitivity.

Acoustic Coherent Backscatter Enhancement from Aggregations of Point Scatterers

DTIC Science & Technology

2015-09-30

and far-field acoustic multiple scattering from two- and now three-dimensional aggregations of omnidirectional point scatterers to determine the...an aggregation of omnidirectional point scatterers [1]. If ψ(r) is the harmonic acoustic pressure field at frequency ω at the point r and ψ0(r) is... scattered field and is given by the sum in (1), N is the number of scatterers , gn is the scattering coefficient of the nth scatterer , ψn(rn) is the field

Absence of solute drag in solidification

NASA Astrophysics Data System (ADS)

Kittl, J. A.; Aziz, M. J.; Brunco, D. P.; Thompson, M. O.

1994-05-01

The interface response functions for alloy solidification were measured in the nondegenerate regime of partial solute trapping. We used a new technique to measure temperatures and velocities simultaneously during rapid solidification of Si-As alloys induced by pulsed laser melting. In addition, partition coefficients were determined using Rutherford backscattering. The results are in good agreement with predictions of the Continuous Growth Model without solute drag of M. J. Aziz and T. Kaplan [Acta Metall. 36, 1335 (1988)] and are inconsistent with all solute drag models.

Reliability and failure modes of narrow implant systems.

PubMed

Hirata, Ronaldo; Bonfante, Estevam A; Anchieta, Rodolfo B; Machado, Lucas S; Freitas, Gileade; Fardin, Vinicius P; Tovar, Nick; Coelho, Paulo G

2016-09-01

Narrow implants are indicated in areas of limited bone width or when grafting is nonviable. However, the reduction of implant diameter may compromise their performance. This study evaluated the reliability of several narrow implant systems under fatigue, after restored with single-unit crowns. Narrow implant systems were divided (n = 18 each), as follows: Astra (ASC); BioHorizons (BSC); Straumann Roxolid (SNC), Intra-Lock (IMC), and Intra-Lock one-piece abutment (ILO). Maxillary central incisor crowns were cemented and subjected to step-stress accelerated life testing in water. Use level probability Weibull curves and reliability for a mission of 100,000 cycles at 130- and 180-N loads (90 % two-sided confidence intervals) were calculated. Scanning electron microscopy was used for fractography. Reliability for 100,000 cycles at 130 N was ∼99 % in group ASC, ∼99 % in BSC, ∼96 % in SNC, ∼99 % in IMC, and ∼100 % in ILO. At 180 N, reliability of ∼34 % resulted for the ASC group, ∼91 % for BSC, ∼53 % for SNC, ∼70 % for IMC, and ∼99 % for ILO. Abutment screw fracture was the main failure mode for all groups. Reliability was not different between systems for 100,000 cycles at the 130-N load. A significant decrease was observed at the 180-N load for ASC, SNC, and IMC, whereas it was maintained for BSC and ILO. The investigated narrow implants presented mechanical performance under fatigue that suggests their safe use as single crowns in the anterior region.

In vitro comparison of intra-abdominal hypertension development after different temporary abdominal closure techniques.

PubMed

Benninger, Emanuel; Labler, Ludwig; Seifert, Burkhardt; Trentz, Otmar; Menger, Michael D; Meier, Christoph

2008-01-01

To compare volume reserve capacity (VRC) and development of intra-abdominal hypertension after different in vitro temporary abdominal closure (TAC) techniques. A model of the abdomen was designed. The abdominal wall was simulated with polychloroprene, a synthetic rubber compound. A lentil-shaped defect of 150 cm(2) was cut into the anterior aspect of the abdominal wall. TAC of this defect was performed by a zipper system (ZS), a bag silo closure (BSC), or a vacuum assisted closure (VAC) with subatmospheric pressures ranging from 0- to 200 mmHg. The model with intact abdominal wall served as reference. The model was filled with water to baseline level. The intra-abdominal pressure was increased in 2 mmHg steps from baseline level (6 mmHg) to 40 mmHg by adding volume to the system according to a standardized protocol. VRC with corresponding intra-abdominal pressure were analyzed and compared for the different TAC techniques. VRC was the highest after BSC at all pressure levels studied (P < 0.05). VAC and ZS resulted in significantly lower VRC compared with BSC and reference (P < 0.05). The magnitude of negative pressure on the VAC did not significantly influence the VRC. In the present in vitro model, BSC demonstrated the highest VRC of all evaluated TAC techniques. Different levels of subatmospheric pressures applied to the VAC did not affect VRC. The results for ZS and VAC indicate that these TAC techniques may increase the risk for recurrent intra-abdominal hypertension and should therefore not be used in high-risk patients during the initial phase after abdominal decompression.

Realization of back-side heterogeneous hybrid III-V/Si DBR lasers for silicon photonics

NASA Astrophysics Data System (ADS)

Durel, Jocelyn; Ferrotti, Thomas; Chantre, Alain; Cremer, Sébastien; Harduin, Julie; Bernabé, Stéphane; Kopp, Christophe; Boeuf, Frédéric; Ben Bakir, Badhise; Broquin, Jean-Emmanuel

2016-02-01

In this paper, the simulation, design and fabrication of a back-side coupling (BSC) concept for silicon photonics, which targets heterogeneous hybrid III-V/Si laser integration is presented. Though various demonstrations of a complete SOI integration of passive and active photonic devices have been made, they all feature multi-level planar metal interconnects, and a lack of integrated light sources. This is mainly due to the conflict between the need of planar surfaces for III-V/Si bonding and multiple levels of metallization. The proposed BSC solution to this topographical problem consists in fabricating lasers on the back-side of the Si waveguides using a new process sequence. The devices are based on a hybrid structure composed of an InGaAsP MQW active area and a Si-based DBR cavity. The emitted light wavelength is accordable within a range of 20 nm around 1.31μm thanks to thermal heaters and the laser output is fiber coupled through a Grating Coupler (GC). From a manufacturing point of view, the BSC approach provides not only the advantages of allowing the use of a thin-BOX SOI instead of a thick one; but it also shifts the laser processing steps and their materials unfriendly to CMOS process to the far back-end areas of fabrication lines. Moreover, aside from solving technological integration issues, the BSC concept offers several new design opportunities for active and passive devices (heat sink, Bragg gratings, grating couplers enhanced with integrated metallic mirrors, tapers…). These building boxes are explored here theoretically and experimentally.

Aerosol Profile Retrievals from Integrated Dual Wavelengths Space Lidar ESSP3-CENA and Spectral Radiance MODIS Data

NASA Technical Reports Server (NTRS)

Kaufman, Yoram; Mattoo, Shana; Tanre, Didier; Kleidman, Richard; Lau, William K. M. (Technical Monitor)

2001-01-01

The ESSP3-CENA space mission (formally PICASSO-CENA) will provide continues global observations with a two wavelength lidar. The attenuated backscattering coefficients measured by the lidar, have valuable information about the vertical distribution of aerosol particles and their sizes. However the information cannot be mapped into unique aerosol physical properties. Infinite number of physical solutions with different attenuations through the atmosphere can reconstruct the same two wavelength backscattered profile measured from space. Spectral radiance measured by MODIS simultaneously with the ESSP3 data can constrain the problem and resolve this ambiguity to a large extent. Sensitivity study shows that inversion of the integrated MODIS+ESSP3 data can derive the vertical profiles of the fine and coarse modes mixed in the same atmospheric column in the presence of moderate calibration uncertainties and electronic noise (approx. 10%). We shall present the sensitivity study and results from application of the technique to measurements in the SAFARI-2000 and SHADE experiments.

An ultra-high gain and efficient amplifier based on Raman amplification in plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vieux, G.; Cipiccia, S.; Grant, D. W.

Raman amplification arising from the excitation of a density echelon in plasma could lead to amplifiers that significantly exceed current power limits of conventional laser media. Here we show that 1–100 J pump pulses can amplify picojoule seed pulses to nearly joule level. The extremely high gain also leads to significant amplification of backscattered radiation from “noise”, arising from stochastic plasma fluctuations that competes with externally injected seed pulses, which are amplified to similar levels at the highest pump energies. The pump energy is scattered into the seed at an oblique angle with 14 J sr -1, and net gainsmore » of more than eight orders of magnitude. The maximum gain coefficient, of 180 cm -1, exceeds high-power solid-state amplifying media by orders of magnitude. The observation of a minimum of 640 J sr -1 directly backscattered from noise, corresponding to ≈10% of the pump energy in the observation solid angle, implies potential overall efficiencies greater than 10%.« less

An ultra-high gain and efficient amplifier based on Raman amplification in plasma

DOE PAGES

Vieux, G.; Cipiccia, S.; Grant, D. W.; ...

2017-05-25

Raman amplification arising from the excitation of a density echelon in plasma could lead to amplifiers that significantly exceed current power limits of conventional laser media. Here we show that 1–100 J pump pulses can amplify picojoule seed pulses to nearly joule level. The extremely high gain also leads to significant amplification of backscattered radiation from “noise”, arising from stochastic plasma fluctuations that competes with externally injected seed pulses, which are amplified to similar levels at the highest pump energies. The pump energy is scattered into the seed at an oblique angle with 14 J sr -1, and net gainsmore » of more than eight orders of magnitude. The maximum gain coefficient, of 180 cm -1, exceeds high-power solid-state amplifying media by orders of magnitude. The observation of a minimum of 640 J sr -1 directly backscattered from noise, corresponding to ≈10% of the pump energy in the observation solid angle, implies potential overall efficiencies greater than 10%.« less

Analysis-Software for Hyperspectral Algal Reflectance Probes v. 1.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Timlin, Jerilyn A.; Reichardt, Thomas A.; Jenson, Travis J.

This software provides onsite analysis of the hyperspectral reflectance data acquired on an outdoor algal pond by a multichannel, fiber-coupled spectroradiometer. The analysis algorithm is based on numerical inversion of a reflectance model, in which the above-water reflectance is expressed as a function of the single backscattering albedo, which is dependent on the backscatter and absorption coefficients of the algal culture, which are in turn related to the algal biomass and pigment optical activity, respectively. Prior to the development of this software, while raw multichannel data were displayed in real time, analysis required a post-processing procedure to extract the relevantmore » parameters. This software provides the capability to track the temporal variation of such culture parameters in real time, as raw data are being acquired, or can be run in a post processing mode. The software allows the user to select between different algal species, incorporate the appropriate calibration data, and observe the quality of the resulting model inversions.« less

Efficient Strategies for Estimating the Spatial Coherence of Backscatter

PubMed Central

Hyun, Dongwoon; Crowley, Anna Lisa C.; Dahl, Jeremy J.

2017-01-01

The spatial coherence of ultrasound backscatter has been proposed to reduce clutter in medical imaging, to measure the anisotropy of the scattering source, and to improve the detection of blood flow. These techniques rely on correlation estimates that are obtained using computationally expensive strategies. In this study, we assess existing spatial coherence estimation methods and propose three computationally efficient modifications: a reduced kernel, a downsampled receive aperture, and the use of an ensemble correlation coefficient. The proposed methods are implemented in simulation and in vivo studies. Reducing the kernel to a single sample improved computational throughput and improved axial resolution. Downsampling the receive aperture was found to have negligible effect on estimator variance, and improved computational throughput by an order of magnitude for a downsample factor of 4. The ensemble correlation estimator demonstrated lower variance than the currently used average correlation. Combining the three methods, the throughput was improved 105-fold in simulation with a downsample factor of 4 and 20-fold in vivo with a downsample factor of 2. PMID:27913342

Synthesis, spectroscopic (FT-IR, FT-Raman, NMR, UV-Visible), Fukui function, antimicrobial and molecular docking study of (E)-1-(3-bromobenzylidene)semicarbazide by DFT method

NASA Astrophysics Data System (ADS)

Raja, M.; Raj Muhamed, R.; Muthu, S.; Suresh, M.; Muthu, K.

2017-02-01

The title compound, (E)-1-(3-bromobenzylidene)semicarbazide (3BSC) was synthesized and characterized by FT-IR, FT-Raman, UV, 1HNMR and 13CNMR spectral analysis. The optimized molecular geometry, the vibrational wavenumbers, the infrared intensities and the Raman scattering activities were calculated by using density functional theory (DFT) B3LYP method with 6-311++G(d,p) basis set. The calculated HOMO and LUMO energies show that charge transfer within the molecule. Stability of the molecule arising from hyperconjugative interactions, charge delocalization have been analyzed using natural bond orbital analysis (NBO). The hyperpolarizability calculation reveals the present material has a reasonably good propensity for nonlinear optical activity. Molecular electrostatic potential (MEP) and Fukui functions were also performed. The thermodynamic properties (heat capacity, entropy, and enthalpy) of the 3BSC at different temperatures have been calculated. The biological applications of 3BSC have been screened for its antimicrobial activity and found to exhibit antifungal and antibacterial effects. In addition, the Molecular docking was also performed for the different receptors.

A balanced scorecard approach in assessing IT value in healthcare sector: an empirical examination.

PubMed

Wu, Ing-Long; Kuo, Yi-Zu

2012-12-01

Healthcare sector indicates human-based and knowledge-intensive property. Massive IT investments are necessary to maintain competitiveness in this sector. The justification of IT investments is the major concern of senior management. Empirical studies examining IT value have found inconclusive results with little or no improvement in productivity. Little research has been conducted in healthcare sector. The balanced scorecard (BSC) strikes a balance between financial and non-financial measure and has been applied in evaluating organization-based performance. Moreover, healthcare organizations often consider their performance goal at customer satisfaction in addition to financial performance. This research thus proposed a new hierarchical structure for the BSC with placing both finance and customer at the top, internal process at the next, and learning and growth at the bottom. Empirical examination has found the importance of the new BSC structure in assessing IT investments. Learning and growth plays the initial driver for reaching both customer and financial performance through the mediator of internal process. This can provide deep insight into effectively managing IT resources in the hospitals.

Transformations, Inc. Net Zero Energy Communities, Devens, Easthampton, Townsend, Massachusetts (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2013-11-01

In 2009, Transformations, Inc. partnered with U.S. Department of Energy (DOE) Building America team Building Science Corporation (BSC) to build new net zero energy houses in three developments in Massachusetts. The company has been developing strategies for cost-effective super-insulated homes in the New England market since 2006. After years of using various construction techniques, it has developed a specific set of assemblies and specifications that achieve a 44.9% reduction in energy use compared with a home built to the 2009 International Residential Code, qualifying the houses for the DOE's Challenge Home. The super-insulated houses provide data for several research topicsmore » in a cold climate. BSC studied the moisture risks in double stud walls insulated with open cell spray foam and cellulose. The mini-split air source heat pump (ASHP) research focused on the range of temperatures experienced in bedrooms as well as the homeowners' perceptions of equipment performance. BSC also examined the developer's financing options for the photovoltaic (PV) systems, which take advantage of Solar Renewable Energy Certificates, local incentives, and state and federal tax credits.« less

Density-dependent regulation of growth of BSC-1 cells in cell culture: growth inhibitors formed by the cells.

PubMed Central

Holley, R W; Armour, R; Baldwin, J H

1978-01-01

Inhibitors formed by a monkey epithelial cell line, BSC-1, play an important role in limiting growth at high cell densities. At least three inhibitors are formed: lactic acid, ammonia, and an unidentified inhibitor that may be an unstable protein. The unidentified inhibitor is destroyed by shaking the conditioned medium, by bubbling gas through the medium, or by heating or storing the medium in the absence of cells. The concentrations of lactic acid and ammonia that accumulate in conditioned medium inhibit growth when added to fresh medium. These results, together with earlier studies, indicate that density-dependent regulation of growth of BSC-1 cells results from the combined effects of (a) inhibitors formed by the cells, (b) decreased availability of receptor sites for serum growth factors as the cells become crowded, and (c) limiting concentrations of low molecular weight nutrients in the medium. In contrast, density-dependent regulation of growth in 3T3 mouse embryo fibroblasts results almost entirely from inactivation of serum factors. PMID:273914

Extinction-to-Backscatter Ratios of Saharan Dust Layers Derived from In-Situ Measurements and CALIPSO Overflights During NAMMA

NASA Technical Reports Server (NTRS)

Omar, Ali H.; Liu, Zhaoyan; Vaughan, Mark A.; Hu, Yongxiang; Ismail, Syed; Powell, Kathleen A.; Winker, David M.; Trepte, Charles R.; Anderson, Bruce E.

2010-01-01

We determine the aerosol extinction-to-backscatter (Sa) ratios of dust using airborne in-situ measurements of microphysical properties, and CALIPSO observations during the NASA African Monsoon Multidisciplinary Analyses (NAMMA). The NAMMA field experiment was conducted from Sal, Cape Verde during Aug-Sept 2006. Using CALIPSO measurements of the attenuated backscatter of lofted Saharan dust layers, we apply the transmittance technique to estimate dust Sa ratios at 532 nm and a 2-color method to determine the corresponding 1064 nm Sa. Using this method, we found dust Sa ratios of 39.8 plus or minus 1.4 sr and 51.8 plus or minus 3.6 sr at 532 nm and 1064 nm, respectively. Secondly, Sa ratios at both wavelengths is independently calculated using size distributions measured aboard the NASA DC-8 and estimates of Saharan dust complex refractive indices applied in a T-Matrix scheme. We found Sa ratios of 39.1 plus or minus 3.5 sr and 50.0 plus or minus 4 sr at 532 nm and 1064 nm, respectively, using the T-Matrix calculations applied to measured size spectra. Finally, in situ measurements of the total scattering (550 nm) and absorption coefficients (532 nm) are used to generate an extinction profile that is used to constrain the CALIPSO 532 nm extinction profile.

A fixed full-matrix method for determining ice sheet height change from satellite altimeter: an ENVISAT case study in East Antarctica with backscatter analysis

NASA Astrophysics Data System (ADS)

Yang, Yuande; Hwang, Cheinway; E, Dongchen

2014-09-01

A new method, called the fixed full-matrix method (FFM), is used to compute height changes at crossovers of satellite altimeter ground tracks. Using the ENVISAT data in East Antarctica, FFM results in crossovers of altimeter heights that are 1.9 and 79 times more than those from the fixed half method (FHM) and the one-row method (ORM). The mean standard error of height changes is about 14 cm from ORM, which is reduced to 7 cm by FHM and to 3 cm by FFM. Unlike FHM, FFM leads to uniform errors in the first-half and second-half height-change time series. FFM has the advantage in improving the accuracy of the change of height and backscattered power over ORM and FHM. Assisted by the ICESat-derived height changes, we determine the optimal threshold correlation coefficient (TCC) for a best correction for the backscatter effect on ENVISAT height changes. The TCC value of 0.92 yields an optimal result for FFM. With this value, FFM yields ENVISAT-derived height change rates in East Antarctica mostly falling between and 3 cm/year, and matching the ICESat result to 0.94 cm/year. The ENVISAT result will provide a constraint on the current mass balance result along the Chinese expedition route CHINARE.

Lidars for smoke and dust cloud diagnostics

NASA Astrophysics Data System (ADS)

Fujimura, S. F.; Warren, R. E.; Lutomirski, R. F.

1980-11-01

An algorithm that integrates a time-resolved lidar signature for use in estimating transmittance, extinction coefficient, mass concentration, and CL values generated under battlefield conditions is applied to lidar signatures measured during the DIRT-I tests. Estimates are given for the dependence of the inferred transmittance and extinction coefficient on uncertainties in parameters such as the obscurant backscatter-to-extinction ratio. The enhanced reliability in estimating transmittance through use of a target behind the obscurant cloud is discussed. It is found that the inversion algorithm can produce reliable estimates of smoke or dust transmittance and extinction from all points within the cloud for which a resolvable signal can be detected, and that a single point calibration measurement can convert the extinction values to mass concentration for each resolvable signal point.

A multicentre randomised controlled trial and economic evaluation of continuous positive airway pressure for the treatment of obstructive sleep apnoea syndrome in older people: PREDICT.

PubMed

McMillan, Alison; Bratton, Daniel J; Faria, Rita; Laskawiec-Szkonter, Magda; Griffin, Susan; Davies, Robert J; Nunn, Andrew J; Stradling, John R; Riha, Renata L; Morrell, Mary J

2015-06-01

The therapeutic and economic benefits of continuous positive airway pressure (CPAP) for the treatment of obstructive sleep apnoea syndrome (OSAS) have been established in middle-aged people. In older people there is a lack of evidence. To determine the clinical efficacy of CPAP in older people with OSAS and to establish its cost-effectiveness. A randomised, parallel, investigator-blinded multicentre trial with within-trial and model-based cost-effectiveness analysis. Two hundred and seventy-eight patients, aged ≥ 65 years with newly diagnosed OSAS [defined as oxygen desaturation index at ≥ 4% desaturation threshold level for > 7.5 events/hour and Epworth Sleepiness Scale (ESS) score of ≥ 9] recruited from 14 hospital-based sleep services across the UK. CPAP with best supportive care (BSC) or BSC alone. Autotitrating CPAP was initiated using standard clinical practice. BSC was structured advice on minimising sleepiness. Subjective sleepiness at 3 months, as measured by the ESS (ESS mean score: months 3 and 4) and cost-effectiveness over 12 months, as measured in quality-adjusted life-years (QALYs) calculated using the European Quality of Life-5 Dimensions (EQ-5D) and health-care resource use, information on which was collected monthly from patient diaries. Subjective sleepiness at 12 months (ESS mean score: months 10, 11 and 12) and objective sleepiness, disease-specific and generic quality of life, mood, functionality, nocturia, mobility, accidents, cognitive function, cardiovascular risk factors and events at 3 and 12 months. Two hundred and seventy-eight patients were randomised to CPAP (n = 140) or BSC (n = 138) over 27 months and 231 (83%) patients completed the trial. Baseline ESS score was similar in both groups [mean (standard deviation; SD) CPAP 11.5 (3.3), BSC 11.4 (4.2)]; groups were well balanced for other characteristics. The mean (SD) in ESS score at 3 months was -3.8 (0.4) in the CPAP group and -1.6 (0.3) in the BSC group. The adjusted treatment effect of CPAP compared with BSC was -2.1 points [95% confidence interval (CI) -3.0 to -1.3 points; p < 0.001]. At 12 months the effect was -2.0 points (95% CI -2.8 to -1.2 points; p < 0.001). The effect was greater in patients with increased CPAP use or higher baseline ESS score. The number of QALYs calculated using the EQ-5D was marginally (0.005) higher with CPAP than with BSC (95% CI -0.034 to 0.044). The average cost per patient was £1363 (95% CI £1121 to £1606) for those allocated to CPAP and £1389 (95% CI £1116 to £1662) for those allocated to BSC. On average, costs were lower in the CPAP group (mean -£35; 95% CI -£390 to £321). The probability that CPAP was cost-effective at thresholds conventionally used by the NHS (£20,000 per QALY gained) was 0.61. QALYs calculated using the Short Form questionnaire-6 Dimensions were 0.018 higher in the CPAP group (95% CI 0.003 to 0.034 QALYs) and the probability that CPAP was cost-effective was 0.96. CPAP decreased objective sleepiness (p = 0.02), increased mobility (p = 0.03) and reduced total and low-density lipoprotein cholesterol (p = 0.05, p = 0.04, respectively) at 3 months but not at 12 months. In the BSC group, there was a fall in systolic blood pressure of 3.7 mmHg at 12 months, which was not seen in the CPAP group (p = 0.04). Mood, functionality, nocturia, accidents, cognitive function and cardiovascular events were unchanged. There were no medically significant harms attributable to CPAP. In older people with OSAS, CPAP reduces sleepiness and is marginally more cost-effective than BSC over 12 months. Further work is required in the identification of potential biomarkers of sleepiness and those patients at increased risk of cognitive impairment. Early detection of which could be used to inform the clinician when in the disease cycle treatment is needed to avert central nervous system sequelae and to assist patients decision-making regarding treatment and compliance. Treatment adherence is also a challenge in clinical trials generally, and adherence to CPAP therapy in particular is a recognised concern in both research studies and clinical practice. Suggested research priorities would include a focus on optimisation of CPAP delivery or support and embracing the technological advances currently available. Finally, the improvements in quality of life in trials do not appear to reflect the dramatic changes noted in clinical practice. There should be a greater focus on patient centred outcomes which would better capture the symptomatic improvement with CPAP treatment and translate these improvements into outcomes which could be used in health economic analysis. Current Controlled Trials ISRCTN90464927. This project was funded by the National Institute for Health Research (NIHR) Health Technology Assessment programme and will be published in full in Health Technology Assessment; Vol. 19, No. 40. See the NIHR Journals Library website for further project information.

Soil physical conditions as livestock treading effect in tropical Agroecosystem of dryland and strategies to mitigate desertification risk

NASA Astrophysics Data System (ADS)

Florentino, A.; Torres, D.; Ospina, A.; Contreras, J.; Palma, Z.; Silvera, J.

2012-04-01

Soil degradation in natural ecosystem of arid and semi-arid zones of Venezuela due to livestock treading (goats) it is an important problem that affect their environment functions; increase soil erodibility, bulk density, water losses and reduce porosity, water infiltration rate and soil structural stability. The presence of biological crust (BSC) in this type of soil it is very common. The objective of this study was to evaluate the soil surface physical quality through the use of selected indicators, mainly some of that related to structural stability, infiltrability and the prediction of soil erosion risk in two zones of Lara state: 1) Quíbor (QUI) and 2) Humocaro Bajo (HB). The study was conducted on two selected plots (30 m x 20 m) in each zone, with natural vegetation and BSC cover, with areas affected by different degree of compaction due to treading in the paths where the goats are moving. Five sites per plot (50 cm x 50 cm) under vegetation cover and five sites over the path with bare soil were sampled (0-7,5 and 7,5-15 cm depth). The results showed that soil macroaggregate stability (equivalent diameter of aggregates >0,25 mm) was significantly higher (p<0,05 %) in soil with vegetation cover and BSC compared with bare soil. Sealing index, as a measure of aggregate stability, determined in laboratory under simulated rain and expressed as hydraulic conductivity of soil surface sealing (Kse), decreased with decreasing soil vegetation cover and the presence of BSC. However, Ksei (i: inicial) and Ksef (f: final) were significantly greater in soil with more than 75 % of BSC in comparison to bare soils. The sealing index it is used to for to estimate changes in soil water losses. As the sealing index increases, the susceptibility of the soil to undergo surface sealing or slaking decrease. These results suggested that soil physical properties are potential indicators of soil quality with regard to soil erodibility and showed that soils under vegetation cover had higher quality level than bare soils. Some predictive regression equation had a high R2 value and was a useful tool for to evaluate the risk of extreme climatic changes and to mitigate their detrimental effects. We conclude that the global climatic change (CCG) will have a negative effect on these agroecosystems functions, mainly in soil and water conservation, carbon sequestration, and productivity. Natural recovery of soil physical properties from treading damage of pastoral soils will be possible in the future with the implementation of soil management strategies, mainly through re-vegetation and recuperation of the BSC. Key word: Soil structure; aggregate stability; soil sealing index; hydraulic conductivity of surface sealing.

Active microwave measurement of soil water content

NASA Technical Reports Server (NTRS)

Ulaby, F. T.; Cihlar, J.; Moore, R. K.

1974-01-01

Measurements of radar backscatter from bare soil at 4.7, 5.9, and 7.1 GHz for incident angles of 0-70 deg have been analyzed to determine sensitivity to soil moisture. Because the effective depth of penetration of the radar signal is only about one skin depth, the observed signals were correlated with the moisture in a skin depth as characterized by the attenuation coefficient (reciprocal of skin depth). Since the attenuation coefficient is a monotonically increasing function of moisture density, it may also be used as a measure of moisture content over the distance involved, which varies with frequency and moisture content. The measurements show an approximately linear increase in scattering with attenuation coefficient of the soil at angles within 10 deg of vertical and all frequencies. At 4.7 GHz this increase continues relatively large out to 70 deg incidence, but by 7.1 GHz the sensitivity is much less even at 20 deg and practically gone at 50 deg.

Implementation of an Analytical Raman Scattering Correction for Satellite Ocean-Color Processing

NASA Technical Reports Server (NTRS)

McKinna, Lachlan I. W.; Werdell, P. Jeremy; Proctor, Christopher W.

2016-01-01

Raman scattering of photons by seawater molecules is an inelastic scattering process. This effect can contribute significantly to the water-leaving radiance signal observed by space-borne ocean-color spectroradiometers. If not accounted for during ocean-color processing, Raman scattering can cause biases in derived inherent optical properties (IOPs). Here we describe a Raman scattering correction (RSC) algorithm that has been integrated within NASA's standard ocean-color processing software. We tested the RSC with NASA's Generalized Inherent Optical Properties algorithm (GIOP). A comparison between derived IOPs and in situ data revealed that the magnitude of the derived backscattering coefficient and the phytoplankton absorption coefficient were reduced when the RSC was applied, whilst the absorption coefficient of colored dissolved and detrital matter remained unchanged. Importantly, our results show that the RSC did not degrade the retrieval skill of the GIOP. In addition, a timeseries study of oligotrophic waters near Bermuda showed that the RSC did not introduce unwanted temporal trends or artifacts into derived IOPs.

A Bidirectional Subsurface Remote Sensing Reflectance Model Explicitly Accounting for Particle Backscattering Shapes

NASA Astrophysics Data System (ADS)

He, Shuangyan; Zhang, Xiaodong; Xiong, Yuanheng; Gray, Deric

2017-11-01

The subsurface remote sensing reflectance (rrs, sr-1), particularly its bidirectional reflectance distribution function (BRDF), depends fundamentally on the angular shape of the volume scattering functions (VSFs, m-1 sr-1). Recent technological advancement has greatly expanded the collection, and the knowledge of natural variability, of the VSFs of oceanic particles. This allows us to test the Zaneveld's theoretical rrs model that explicitly accounts for particle VSF shapes. We parameterized the rrs model based on HydroLight simulations using 114 VSFs measured in three coastal waters around the United States and in oceanic waters of North Atlantic Ocean. With the absorption coefficient (a), backscattering coefficient (bb), and VSF shape as inputs, the parameterized model is able to predict rrs with a root mean square relative error of ˜4% for solar zenith angles from 0 to 75°, viewing zenith angles from 0 to 60°, and viewing azimuth angles from 0 to 180°. A test with the field data indicates the performance of our model, when using only a and bb as inputs and selecting the VSF shape using bb, is comparable to or slightly better than the currently used models by Morel et al. and Lee et al. Explicitly expressing VSF shapes in rrs modeling has great potential to further constrain the uncertainty in the ocean color studies as our knowledge on the VSFs of natural particles continues to improve. Our study represents a first effort in this direction.

Temporally Coincident Lidar Measurements from UMBC with CALIPSO during the Initial Validation Period

NASA Astrophysics Data System (ADS)

Hoff, R. M.; Delgado, R.; Rogers, R.; Torres, O.; McCann, K.

2006-12-01

During June-October, 2006, the University of Maryland, Baltimore County Elastic Lidar Facilty (ELF) was operated for over 30 overpasses of the CALIPSO satellite. Like CALIPSO, the ELF operates at 532 nm and 1064 nm and has polarization capability. Many of these overpasses were temporally well aligned but were considerably distant from the UMBC campus. Since the aerosol features in the lowest part of the boundary layer are dynamic, "validation" of the CALIPSO profiles from such a ground-based data set is nearly impossible. This paper will examine the suite of overpass measurements in a statistical sense. Cases where the UMBC lidar and Calipso attenuated backscatter coefficient can be compared by difference as a function of height will be shown. Additionally, probability density functions (PDF) of attenuated backscatter coefficient within the PBL and above for various spatial offsets are examined. Digital data from the CALIOP lidar on CALIPSO is only beginning to be released at the time of writing of this abstract and this paper will present a more thorough comparison of these cases at the AGU meeting. The validation data taken during this period also revealed transport of plumes of smoke from Canada over UMBC. We have used the UMBC lidar data and the CALIPSO data to help constrain retrievals in the Ozone Monitoring Instrument (OMI) aerosol optical depth data. An example of how this synergistic use of instruments on two satellites and from the ground during A-Train overpasses will be discussed.

Application of Vorob'ev's asymptotic solution to retrieval of the structural characteristics Cn2 from BSA-lidar data

NASA Astrophysics Data System (ADS)

Razenkov, I. A.

2017-11-01

Micro pulse lasers have allowed solution of some technical problems and design of a specialized aerosol lidar capable of recording backscattering amplification (BSA) in a turbulent atmosphere (2014) by now. The BSA-lidar has two receiving channels, one of which is affected by a turbulence. The measurement result is the ratio of echo signals, i.e., the coefficient of backscattering amplification. The problem of lidar data inversion and retrieval of "optical" turbulence parameters was recently solved by V.V. Vorob'ev theoretically (2016). A lidar experiment was organized for testing the solution, and the asymptotic solution was applied to echo signals, which allowed estimating the daily behavior of the structural characteristics Cn 2 along a horizontal 2-km path. The experiment was accompanied by parallel independent measurements of Cn 2 by an image jitter sensor along the same path. It was shown experimentally that the Vorob'ev solution is applicable to Cn 2 retrieval from BSA-lidar data if β0 2<=3 for β0 2>3, the saturation of the amplification effect and a decrease in the experimental data with respect to calculation results are observed. The coefficient of correlation between the retrieved structural characteristics Cn 2 of the lidar and jitter sensor is 0.8-0.9. The Cn 2 values retrieved from lidar signals turned out to be 20-40% lower than the Cn 2 values of the image jitter sensor.

Smsynth: AN Imagery Synthesis System for Soil Moisture Retrieval

NASA Astrophysics Data System (ADS)

Cao, Y.; Xu, L.; Peng, J.

2018-04-01

Soil moisture (SM) is a important variable in various research areas, such as weather and climate forecasting, agriculture, drought and flood monitoring and prediction, and human health. An ongoing challenge in estimating SM via synthetic aperture radar (SAR) is the development of the retrieval SM methods, especially the empirical models needs as training samples a lot of measurements of SM and soil roughness parameters which are very difficult to acquire. As such, it is difficult to develop empirical models using realistic SAR imagery and it is necessary to develop methods to synthesis SAR imagery. To tackle this issue, a SAR imagery synthesis system based on the SM named SMSynth is presented, which can simulate radar signals that are realistic as far as possible to the real SAR imagery. In SMSynth, SAR backscatter coefficients for each soil type are simulated via the Oh model under the Bayesian framework, where the spatial correlation is modeled by the Markov random field (MRF) model. The backscattering coefficients simulated based on the designed soil parameters and sensor parameters are added into the Bayesian framework through the data likelihood where the soil parameters and sensor parameters are set as realistic as possible to the circumstances on the ground and in the validity range of the Oh model. In this way, a complete and coherent Bayesian probabilistic framework is established. Experimental results show that SMSynth is capable of generating realistic SAR images that suit the needs of a large amount of training samples of empirical models.

In vitro chronic hepatic disease characterization with a multiparametric ultrasonic approach.

PubMed

Meziri, M; Pereira, W C A; Abdelwahab, A; Degott, C; Laugier, P

2005-03-01

Although, high resolution, real-time ultrasonic (US) imaging is routinely available, image interpretation is based on grey-level and texture and quantitative evaluation is limited. Other potentially useful diagnostic information from US echoes may include modifications in tissue acoustic parameters (speed, attenuation and backscattering) resulting from disease development. Changes in acoustical parameters can be detected using time-of-flight and spectral analysis techniques. The objective of this study is to explore the potential of three parameters together (attenuation coefficient, US speed and integrated backscatter coefficient-IBC) to discriminate healthy and fibrosis subgroups in liver tissue. Echoes from 21 fresh in vitro samples of human liver and from a plane reflector were obtained using a 20-MHz central frequency transducer (6-30 MHz bandpass). The scan plane was parallel to the reflector placed beneath the liver. A 30 x 20 matrix of A-scans was obtained, with a 200-microm step. The samples were classified according to the Metavir scale in five different degrees of fibrosis. US speed, attenuation and IBC were estimated from standard methods described in the literature. Statistical tests were applied to the results of each parameter individually and indicated that it was not possible to identify all the fibrosis groups. Then a discriminant analysis was performed for the three parameters together resulting in a reasonable separation of fibrotic groups. Although the number of tissue samples is limited, this study opens the possibility of enhancing the discriminant capability of ultrasonic parameters of liver tissue disease when they are combined together.